Limitations of Community College Benchmarking and Benchmarks

ERIC Educational Resources Information Center

Bers, Trudy H.

2006-01-01

This chapter distinguishes between benchmarks and benchmarking, describes a number of data and cultural limitations to benchmarking projects, and suggests that external demands for accountability are the dominant reason for growing interest in benchmarking among community colleges.

Benchmark test of neutron transport calculations: indium, nickel, gold, europium, and cobalt activation with and without energy moderated fission neutrons by iron simulating the Hiroshima atomic bomb casing.

PubMed

Iwatani, K; Hoshi, M; Shizuma, K; Hiraoka, M; Hayakawa, N; Oka, T; Hasai, H

1994-10-01

A benchmark test of the Monte Carlo neutron and photon transport code system (MCNP) was performed using a bare- and energy-moderated 252Cf fission neutron source which was obtained by transmission through 10-cm-thick iron. An iron plate was used to simulate the effect of the Hiroshima atomic bomb casing. This test includes the activation of indium and nickel for fast neutrons and gold, europium, and cobalt for thermal and epithermal neutrons, which were inserted in the moderators. The latter two activations are also to validate 152Eu and 60Co activity data obtained from the atomic bomb-exposed specimens collected at Hiroshima and Nagasaki, Japan. The neutron moderators used were Lucite and Nylon 6 and the total thickness of each moderator was 60 cm or 65 cm. Measured activity data (reaction yield) of the neutron-irradiated detectors in these moderators decreased to about 1/1,000th or 1/10,000th, which corresponds to about 1,500 m ground distance from the hypocenter in Hiroshima. For all of the indium, nickel, and gold activity data, the measured and calculated values agreed within 25%, and the corresponding values for europium and cobalt were within 40%. From this study, the MCNP code was found to be accurate enough for the bare- and energy-moderated 252Cf neutron activation calculations of these elements using moderators containing hydrogen, carbon, nitrogen, and oxygen.

On the way to unveiling the atomic structure of superheavy elements

NASA Astrophysics Data System (ADS)

Laatiaoui, Mustapha

2016-12-01

Optical spectroscopy of the transfermium elements (atomic number Z > 100) is nowadays one of the most fascinating and simultaneously challenging tasks in atomic physics. On the one hand, key atomic and even nuclear ground-state properties may be obtained by studying the spectral lines of these heaviest elements. On the other hand, these elements have to be produced "online" by heavy-ion induced fusion-evaporation reactions yielding rates on the order of a few atoms per second at most, which renders their optical spectroscopy extremely difficult. Only recently, a first foray of laser spectroscopy into this heaviest element region was reported. Several atomic transitions in the element nobelium (Z = 102) were observed and characterized, using an ultra-sensitive and highly efficient resonance ionization technique. The findings confirm the predictions and additionally provide a benchmark for theoretical modelling. The work represents an important stepping stone towards experimental studies of the atomic structure of superheavy elements.

Solution of the neutronics code dynamic benchmark by finite element method

NASA Astrophysics Data System (ADS)

Avvakumov, A. V.; Vabishchevich, P. N.; Vasilev, A. O.; Strizhov, V. F.

2016-10-01

The objective is to analyze the dynamic benchmark developed by Atomic Energy Research for the verification of best-estimate neutronics codes. The benchmark scenario includes asymmetrical ejection of a control rod in a water-type hexagonal reactor at hot zero power. A simple Doppler feedback mechanism assuming adiabatic fuel temperature heating is proposed. The finite element method on triangular calculation grids is used to solve the three-dimensional neutron kinetics problem. The software has been developed using the engineering and scientific calculation library FEniCS. The matrix spectral problem is solved using the scalable and flexible toolkit SLEPc. The solution accuracy of the dynamic benchmark is analyzed by condensing calculation grid and varying degree of finite elements.

Partition coefficients of methylated DNA bases obtained from free energy calculations with molecular electron density derived atomic charges.

PubMed

Lara, A; Riquelme, M; Vöhringer-Martinez, E

2018-05-11

Partition coefficients serve in various areas as pharmacology and environmental sciences to predict the hydrophobicity of different substances. Recently, they have also been used to address the accuracy of force fields for various organic compounds and specifically the methylated DNA bases. In this study, atomic charges were derived by different partitioning methods (Hirshfeld and Minimal Basis Iterative Stockholder) directly from the electron density obtained by electronic structure calculations in a vacuum, with an implicit solvation model or with explicit solvation taking the dynamics of the solute and the solvent into account. To test the ability of these charges to describe electrostatic interactions in force fields for condensed phases, the original atomic charges of the AMBER99 force field were replaced with the new atomic charges and combined with different solvent models to obtain the hydration and chloroform solvation free energies by molecular dynamics simulations. Chloroform-water partition coefficients derived from the obtained free energies were compared to experimental and previously reported values obtained with the GAFF or the AMBER-99 force field. The results show that good agreement with experimental data is obtained when the polarization of the electron density by the solvent has been taken into account, and when the energy needed to polarize the electron density of the solute has been considered in the transfer free energy. These results were further confirmed by hydration free energies of polar and aromatic amino acid side chain analogs. Comparison of the two partitioning methods, Hirshfeld-I and Minimal Basis Iterative Stockholder (MBIS), revealed some deficiencies in the Hirshfeld-I method related to the unstable isolated anionic nitrogen pro-atom used in the method. Hydration free energies and partitioning coefficients obtained with atomic charges from the MBIS partitioning method accounting for polarization by the implicit solvation model

Thermal Performance Benchmarking: Annual Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moreno, Gilbert

2016-04-08

The goal for this project is to thoroughly characterize the performance of state-of-the-art (SOA) automotive power electronics and electric motor thermal management systems. Information obtained from these studies will be used to: Evaluate advantages and disadvantages of different thermal management strategies; establish baseline metrics for the thermal management systems; identify methods of improvement to advance the SOA; increase the publicly available information related to automotive traction-drive thermal management systems; help guide future electric drive technologies (EDT) research and development (R&D) efforts. The performance results combined with component efficiency and heat generation information obtained by Oak Ridge National Laboratory (ORNL) maymore » then be used to determine the operating temperatures for the EDT components under drive-cycle conditions. In FY15, the 2012 Nissan LEAF power electronics and electric motor thermal management systems were benchmarked. Testing of the 2014 Honda Accord Hybrid power electronics thermal management system started in FY15; however, due to time constraints it was not possible to include results for this system in this report. The focus of this project is to benchmark the thermal aspects of the systems. ORNL's benchmarking of electric and hybrid electric vehicle technology reports provide detailed descriptions of the electrical and packaging aspects of these automotive systems.« less

Atomic structure of a metal-supported two-dimensional germania film

NASA Astrophysics Data System (ADS)

Lewandowski, Adrián Leandro; Schlexer, Philomena; Büchner, Christin; Davis, Earl M.; Burrall, Hannah; Burson, Kristen M.; Schneider, Wolf-Dieter; Heyde, Markus; Pacchioni, Gianfranco; Freund, Hans-Joachim

2018-03-01

The growth and microscopic characterization of two-dimensional germania films is presented. Germanium oxide monolayer films were grown on Ru(0001) by physical vapor deposition and subsequent annealing in oxygen. We obtain a comprehensive image of the germania film structure by combining intensity-voltage low-energy electron diffraction (I/V-LEED) and ab initio density functional theory (DFT) analysis with atomic-resolution scanning tunneling microscopy (STM) imaging. For benchmarking purposes, the bare Ru(0001) substrate and the (2 ×2 )3 O covered Ru(0001) were analyzed with I/V-LEED with respect to previous reports. STM topographic images of the germania film reveal a hexagonal network where the oxygen and germanium atom positions appear in different imaging contrasts. For quantitative LEED, the best agreement has been achieved with DFT structures where the germanium atoms are located preferentially on the top and fcc hollow sites of the Ru(0001) substrate. Moreover, in these atomically flat germania films, local site geometries, i.e., tetrahedral building blocks, ring structures, and domain boundaries, have been identified, indicating possible pathways towards two-dimensional amorphous networks.

Gaia FGK benchmark stars: Metallicity

NASA Astrophysics Data System (ADS)

Jofré, P.; Heiter, U.; Soubiran, C.; Blanco-Cuaresma, S.; Worley, C. C.; Pancino, E.; Cantat-Gaudin, T.; Magrini, L.; Bergemann, M.; González Hernández, J. I.; Hill, V.; Lardo, C.; de Laverny, P.; Lind, K.; Masseron, T.; Montes, D.; Mucciarelli, A.; Nordlander, T.; Recio Blanco, A.; Sobeck, J.; Sordo, R.; Sousa, S. G.; Tabernero, H.; Vallenari, A.; Van Eck, S.

2014-04-01

Context. To calibrate automatic pipelines that determine atmospheric parameters of stars, one needs a sample of stars, or "benchmark stars", with well-defined parameters to be used as a reference. Aims: We provide detailed documentation of the iron abundance determination of the 34 FGK-type benchmark stars that are selected to be the pillars for calibration of the one billion Gaia stars. They cover a wide range of temperatures, surface gravities, and metallicities. Methods: Up to seven different methods were used to analyze an observed spectral library of high resolutions and high signal-to-noise ratios. The metallicity was determined by assuming a value of effective temperature and surface gravity obtained from fundamental relations; that is, these parameters were known a priori and independently from the spectra. Results: We present a set of metallicity values obtained in a homogeneous way for our sample of benchmark stars. In addition to this value, we provide detailed documentation of the associated uncertainties. Finally, we report a value of the metallicity of the cool giant ψ Phe for the first time. Based on NARVAL and HARPS data obtained within the Gaia DPAC (Data Processing and Analysis Consortium) and coordinated by the GBOG (Ground-Based Observations for Gaia) working group and on data retrieved from the ESO-ADP database.Tables 6-76 are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (ftp://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/564/A133

A new numerical benchmark of a freshwater lens

NASA Astrophysics Data System (ADS)

Stoeckl, L.; Walther, M.; Graf, T.

2016-04-01

A numerical benchmark for 2-D variable-density flow and solute transport in a freshwater lens is presented. The benchmark is based on results of laboratory experiments conducted by Stoeckl and Houben (2012) using a sand tank on the meter scale. This benchmark describes the formation and degradation of a freshwater lens over time as it can be found under real-world islands. An error analysis gave the appropriate spatial and temporal discretization of 1 mm and 8.64 s, respectively. The calibrated parameter set was obtained using the parameter estimation tool PEST. Comparing density-coupled and density-uncoupled results showed that the freshwater-saltwater interface position is strongly dependent on density differences. A benchmark that adequately represents saltwater intrusion and that includes realistic features of coastal aquifers or freshwater lenses was lacking. This new benchmark was thus developed and is demonstrated to be suitable to test variable-density groundwater models applied to saltwater intrusion investigations.

Evaluation of control strategies using an oxidation ditch benchmark.

PubMed

Abusam, A; Keesman, K J; Spanjers, H; van, Straten G; Meinema, K

2002-01-01

This paper presents validation and implementation results of a benchmark developed for a specific full-scale oxidation ditch wastewater treatment plant. A benchmark is a standard simulation procedure that can be used as a tool in evaluating various control strategies proposed for wastewater treatment plants. It is based on model and performance criteria development. Testing of this benchmark, by comparing benchmark predictions to real measurements of the electrical energy consumptions and amounts of disposed sludge for a specific oxidation ditch WWTP, has shown that it can (reasonably) be used for evaluating the performance of this WWTP. Subsequently, the validated benchmark was then used in evaluating some basic and advanced control strategies. Some of the interesting results obtained are the following: (i) influent flow splitting ratio, between the first and the fourth aerated compartments of the ditch, has no significant effect on the TN concentrations in the effluent, and (ii) for evaluation of long-term control strategies, future benchmarks need to be able to assess settlers' performance.

A comparison of five benchmarks

NASA Technical Reports Server (NTRS)

Huss, Janice E.; Pennline, James A.

1987-01-01

Five benchmark programs were obtained and run on the NASA Lewis CRAY X-MP/24. A comparison was made between the programs codes and between the methods for calculating performance figures. Several multitasking jobs were run to gain experience in how parallel performance is measured.

An analytical benchmark and a Mathematica program for MD codes: Testing LAMMPS on the 2nd generation Brenner potential

NASA Astrophysics Data System (ADS)

Favata, Antonino; Micheletti, Andrea; Ryu, Seunghwa; Pugno, Nicola M.

2016-10-01

An analytical benchmark and a simple consistent Mathematica program are proposed for graphene and carbon nanotubes, that may serve to test any molecular dynamics code implemented with REBO potentials. By exploiting the benchmark, we checked results produced by LAMMPS (Large-scale Atomic/Molecular Massively Parallel Simulator) when adopting the second generation Brenner potential, we made evident that this code in its current implementation produces results which are offset from those of the benchmark by a significant amount, and provide evidence of the reason.

Precise calibration of few-cycle laser pulses with atomic hydrogen

NASA Astrophysics Data System (ADS)

Wallace, W. C.; Kielpinski, D.; Litvinyuk, I. V.; Sang, R. T.

2017-12-01

Interaction of atoms and molecules with strong electric fields is a fundamental process in many fields of research, particularly in the emerging field of attosecond science. Therefore, understanding the physics underpinning those interactions is of significant interest to the scientific community. One crucial step in this understanding is accurate knowledge of the few-cycle laser field driving the process. Atomic hydrogen (H), the simplest of all atomic species, plays a key role in benchmarking strong-field processes. Its wide-spread use as a testbed for theoretical calculations allows the comparison of approximate theoretical models against nearly-perfect numerical solutions of the three-dimensional time-dependent Schrödinger equation. Until recently, relatively little experimental data in atomic H was available for comparison to these models, and was due mostly due to the difficulty in the construction and use of atomic H sources. Here, we review our most recent experimental results from atomic H interaction with few-cycle laser pulses and how they have been used to calibrate important laser pulse parameters such as peak intensity and the carrier-envelope phase (CEP). Quantitative agreement between experimental data and theoretical predictions for atomic H has been obtained at the 10% uncertainty level, allowing for accurate laser calibration intensity at the 1% level. Using this calibration in atomic H, both accurate CEP data and an intensity calibration standard have been obtained Ar, Kr, and Xe; such gases are in common use for strong-field experiments. This calibration standard can be used by any laboratory using few-cycle pulses in the 1014 W cm-2 intensity regime centered at 800 nm wavelength to accurately calibrate their peak laser intensity to within few-percent precision.

The national hydrologic bench-mark network

USGS Publications Warehouse

Cobb, Ernest D.; Biesecker, J.E.

1971-01-01

The United States is undergoing a dramatic growth of population and demands on its natural resources. The effects are widespread and often produce significant alterations of the environment. The hydrologic bench-mark network was established to provide data on stream basins which are little affected by these changes. The network is made up of selected stream basins which are not expected to be significantly altered by man. Data obtained from these basins can be used to document natural changes in hydrologic characteristics with time, to provide a better understanding of the hydrologic structure of natural basins, and to provide a comparative base for studying the effects of man on the hydrologic environment. There are 57 bench-mark basins in 37 States. These basins are in areas having a wide variety of climate and topography. The bench-mark basins and the types of data collected in the basins are described.

The MCNP6 Analytic Criticality Benchmark Suite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Forrest B.

2016-06-16

Analytical benchmarks provide an invaluable tool for verifying computer codes used to simulate neutron transport. Several collections of analytical benchmark problems [1-4] are used routinely in the verification of production Monte Carlo codes such as MCNP® [5,6]. Verification of a computer code is a necessary prerequisite to the more complex validation process. The verification process confirms that a code performs its intended functions correctly. The validation process involves determining the absolute accuracy of code results vs. nature. In typical validations, results are computed for a set of benchmark experiments using a particular methodology (code, cross-section data with uncertainties, and modeling)more » and compared to the measured results from the set of benchmark experiments. The validation process determines bias, bias uncertainty, and possibly additional margins. Verification is generally performed by the code developers, while validation is generally performed by code users for a particular application space. The VERIFICATION_KEFF suite of criticality problems [1,2] was originally a set of 75 criticality problems found in the literature for which exact analytical solutions are available. Even though the spatial and energy detail is necessarily limited in analytical benchmarks, typically to a few regions or energy groups, the exact solutions obtained can be used to verify that the basic algorithms, mathematics, and methods used in complex production codes perform correctly. The present work has focused on revisiting this benchmark suite. A thorough review of the problems resulted in discarding some of them as not suitable for MCNP benchmarking. For the remaining problems, many of them were reformulated to permit execution in either multigroup mode or in the normal continuous-energy mode for MCNP. Execution of the benchmarks in continuous-energy mode provides a significant advance to MCNP verification methods.« less

Combining Phase Identification and Statistic Modeling for Automated Parallel Benchmark Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jin, Ye; Ma, Xiaosong; Liu, Qing Gary

2015-01-01

Parallel application benchmarks are indispensable for evaluating/optimizing HPC software and hardware. However, it is very challenging and costly to obtain high-fidelity benchmarks reflecting the scale and complexity of state-of-the-art parallel applications. Hand-extracted synthetic benchmarks are time-and labor-intensive to create. Real applications themselves, while offering most accurate performance evaluation, are expensive to compile, port, reconfigure, and often plainly inaccessible due to security or ownership concerns. This work contributes APPRIME, a novel tool for trace-based automatic parallel benchmark generation. Taking as input standard communication-I/O traces of an application's execution, it couples accurate automatic phase identification with statistical regeneration of event parameters tomore » create compact, portable, and to some degree reconfigurable parallel application benchmarks. Experiments with four NAS Parallel Benchmarks (NPB) and three real scientific simulation codes confirm the fidelity of APPRIME benchmarks. They retain the original applications' performance characteristics, in particular the relative performance across platforms.« less

The NAS parallel benchmarks

NASA Technical Reports Server (NTRS)

Bailey, David (Editor); Barton, John (Editor); Lasinski, Thomas (Editor); Simon, Horst (Editor)

1993-01-01

A new set of benchmarks was developed for the performance evaluation of highly parallel supercomputers. These benchmarks consist of a set of kernels, the 'Parallel Kernels,' and a simulated application benchmark. Together they mimic the computation and data movement characteristics of large scale computational fluid dynamics (CFD) applications. The principal distinguishing feature of these benchmarks is their 'pencil and paper' specification - all details of these benchmarks are specified only algorithmically. In this way many of the difficulties associated with conventional benchmarking approaches on highly parallel systems are avoided.

Benchmarking and Performance Measurement.

ERIC Educational Resources Information Center

Town, J. Stephen

This paper defines benchmarking and its relationship to quality management, describes a project which applied the technique in a library context, and explores the relationship between performance measurement and benchmarking. Numerous benchmarking methods contain similar elements: deciding what to benchmark; identifying partners; gathering…

The NAS parallel benchmarks

NASA Technical Reports Server (NTRS)

Bailey, D. H.; Barszcz, E.; Barton, J. T.; Carter, R. L.; Lasinski, T. A.; Browning, D. S.; Dagum, L.; Fatoohi, R. A.; Frederickson, P. O.; Schreiber, R. S.

1991-01-01

A new set of benchmarks has been developed for the performance evaluation of highly parallel supercomputers in the framework of the NASA Ames Numerical Aerodynamic Simulation (NAS) Program. These consist of five 'parallel kernel' benchmarks and three 'simulated application' benchmarks. Together they mimic the computation and data movement characteristics of large-scale computational fluid dynamics applications. The principal distinguishing feature of these benchmarks is their 'pencil and paper' specification-all details of these benchmarks are specified only algorithmically. In this way many of the difficulties associated with conventional benchmarking approaches on highly parallel systems are avoided.

Development of the Science Data System for the International Space Station Cold Atom Lab

NASA Technical Reports Server (NTRS)

van Harmelen, Chris; Soriano, Melissa A.

2015-01-01

Cold Atom Laboratory (CAL) is a facility that will enable scientists to study ultra-cold quantum gases in a microgravity environment on the International Space Station (ISS) beginning in 2016. The primary science data for each experiment consists of two images taken in quick succession. The first image is of the trapped cold atoms and the second image is of the background. The two images are subtracted to obtain optical density. These raw Level 0 atom and background images are processed into the Level 1 optical density data product, and then into the Level 2 data products: atom number, Magneto-Optical Trap (MOT) lifetime, magnetic chip-trap atom lifetime, and condensate fraction. These products can also be used as diagnostics of the instrument health. With experiments being conducted for 8 hours every day, the amount of data being generated poses many technical challenges, such as downlinking and managing the required data volume. A parallel processing design is described, implemented, and benchmarked. In addition to optimizing the data pipeline, accuracy and speed in producing the Level 1 and 2 data products is key. Algorithms for feature recognition are explored, facilitating image cropping and accurate atom number calculations.

Atomic charges of sulfur in ionic liquids: experiments and calculations.

PubMed

Fogarty, Richard M; Rowe, Rebecca; Matthews, Richard P; Clough, Matthew T; Ashworth, Claire R; Brandt, Agnieszka; Corbett, Paul J; Palgrave, Robert G; Smith, Emily F; Bourne, Richard A; Chamberlain, Thomas W; Thompson, Paul B J; Hunt, Patricia A; Lovelock, Kevin R J

2017-12-14

Experimental near edge X-ray absorption fine structure (NEXAFS) spectra, X-ray photoelectron (XP) spectra and Auger electron spectra are reported for sulfur in ionic liquids (ILs) with a range of chemical structures. These values provide experimental measures of the atomic charge in each IL and enable the evaluation of the suitability of NEXAFS spectroscopy and XPS for probing the relative atomic charge of sulfur. In addition, we use Auger electron spectroscopy to show that when XPS binding energies differ by less than 0.5 eV, conclusions on atomic charge should be treated with caution. Our experimental data provides a benchmark for calculations of the atomic charge of sulfur obtained using different methods. Atomic charges were computed for lone ions and ion pairs, both in the gas phase (GP) and in a solvation model (SMD), with a wide range of ion pair conformers considered. Three methods were used to compute the atomic charges: charges from the electrostatic potential using a grid based method (ChelpG), natural bond orbital (NBO) population analysis and Bader's atoms in molecules (AIM) approach. By comparing the experimental and calculated measures of the atomic charge of sulfur, we provide an order for the sulfur atoms, ranging from the most negative to the most positive atomic charge. Furthermore, we show that both ChelpG and NBO are reasonable methods for calculating the atomic charge of sulfur in ILs, based on the agreement with both the XPS and NEXAFS spectroscopy results. However, the atomic charges of sulfur derived from ChelpG are found to display significant, non-physical conformational dependence. Only small differences in individual atomic charge of sulfur were observed between lone ion (GP) and ion pair IL(SMD) model systems, indicating that ion-ion interactions do not strongly influence individual atomic charges.

Electron collisions with atoms, ions, molecules, and surfaces: Fundamental science empowering advances in technology

PubMed Central

Bartschat, Klaus; Kushner, Mark J.

2016-01-01

Electron collisions with atoms, ions, molecules, and surfaces are critically important to the understanding and modeling of low-temperature plasmas (LTPs), and so in the development of technologies based on LTPs. Recent progress in obtaining experimental benchmark data and the development of highly sophisticated computational methods is highlighted. With the cesium-based diode-pumped alkali laser and remote plasma etching of Si3N4 as examples, we demonstrate how accurate and comprehensive datasets for electron collisions enable complex modeling of plasma-using technologies that empower our high-technology–based society. PMID:27317740

Development of Benchmark Examples for Static Delamination Propagation and Fatigue Growth Predictions

NASA Technical Reports Server (NTRS)

Kruger, Ronald

2011-01-01

The development of benchmark examples for static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of an End-Notched Flexure (ENF) specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, static benchmark examples were created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during stable delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall, the results are encouraging but further assessment for mixed-mode delamination is required.

Benchmarking in emergency health systems.

PubMed

Kennedy, Marcus P; Allen, Jacqueline; Allen, Greg

2002-12-01

This paper discusses the role of benchmarking as a component of quality management. It describes the historical background of benchmarking, its competitive origin and the requirement in today's health environment for a more collaborative approach. The classical 'functional and generic' types of benchmarking are discussed with a suggestion to adopt a different terminology that describes the purpose and practicalities of benchmarking. Benchmarking is not without risks. The consequence of inappropriate focus and the need for a balanced overview of process is explored. The competition that is intrinsic to benchmarking is questioned and the negative impact it may have on improvement strategies in poorly performing organizations is recognized. The difficulty in achieving cross-organizational validity in benchmarking is emphasized, as is the need to scrutinize benchmarking measures. The cost effectiveness of benchmarking projects is questioned and the concept of 'best value, best practice' in an environment of fixed resources is examined.

Optical oscillator strengths of the valence-shell excitations of atoms and molecules determined by the dipole ( γ,γ) method

NASA Astrophysics Data System (ADS)

Xu, Long-Quan; Liu, Ya-Wei; Xu, Xin; Ni, Dong-Dong; Yang, Ke; Zhu, Lin-Fan

2017-07-01

The dipole (γ,γ) method, which is the inelastic X-ray scattering operated at a negligibly small momentum transfer, has been developed to determine the absolute optical oscillator strengths of the valence-shell excitations of atoms and molecules. This new method is free from the line saturation effect, and its Bethe-Born conversion factor varies much more slowly with the excitation energy than that of the dipole (e, e) method. Thus the dipole (γ,γ) method provides a reliable approach to obtain the benchmark optical oscillator strengths of the valence-shell excitations for gaseous atoms and molecules. In this paper, we give a review of the dipole (γ,γ) method and some recent measurements of absolute optical oscillator strengths of gaseous atoms and molecules. Contribution to the Topical Issue "Atomic and Molecular Data and their Applications", edited by Gordon W.F. Drake, Jung-Sik Yoon, Daiji Kato, Grzegorz Karwasz.

Development of a Benchmark Example for Delamination Fatigue Growth Prediction

NASA Technical Reports Server (NTRS)

Krueger, Ronald

2010-01-01

The development of a benchmark example for cyclic delamination growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of a Double Cantilever Beam (DCB) specimen, which is independent of the analysis software used and allows the assessment of the delamination growth prediction capabilities in commercial finite element codes. First, the benchmark result was created for the specimen. Second, starting from an initially straight front, the delamination was allowed to grow under cyclic loading in a finite element model of a commercial code. The number of cycles to delamination onset and the number of cycles during stable delamination growth for each growth increment were obtained from the analysis. In general, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. Overall, the results are encouraging but further assessment for mixed-mode delamination is required

Revisiting Yasinsky and Henry`s benchmark using modern nodal codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feltus, M.A.; Becker, M.W.

1995-12-31

The numerical experiments analyzed by Yasinsky and Henry are quite trivial by comparison with today`s standards because they used the finite difference code WIGLE for their benchmark. Also, this problem is a simple slab (one-dimensional) case with no feedback mechanisms. This research attempts to obtain STAR (Ref. 2) and NEM (Ref. 3) code results in order to produce a more modern kinetics benchmark with results comparable WIGLE.

Benchmarking reference services: step by step.

PubMed

Buchanan, H S; Marshall, J G

1996-01-01

This article is a companion to an introductory article on benchmarking published in an earlier issue of Medical Reference Services Quarterly. Librarians interested in benchmarking often ask the following questions: How do I determine what to benchmark; how do I form a benchmarking team; how do I identify benchmarking partners; what's the best way to collect and analyze benchmarking information; and what will I do with the data? Careful planning is a critical success factor of any benchmarking project, and these questions must be answered before embarking on a benchmarking study. This article summarizes the steps necessary to conduct benchmarking research. Relevant examples of each benchmarking step are provided.

Development of Benchmark Examples for Quasi-Static Delamination Propagation and Fatigue Growth Predictions

NASA Technical Reports Server (NTRS)

Krueger, Ronald

2012-01-01

The development of benchmark examples for quasi-static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for Abaqus/Standard. The example is based on a finite element model of a Double-Cantilever Beam specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, a quasi-static benchmark example was created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall the results are encouraging, but further assessment for mixed-mode delamination is required.

Benchmarking Data Sets for the Evaluation of Virtual Ligand Screening Methods: Review and Perspectives.

PubMed

Lagarde, Nathalie; Zagury, Jean-François; Montes, Matthieu

2015-07-27

Virtual screening methods are commonly used nowadays in drug discovery processes. However, to ensure their reliability, they have to be carefully evaluated. The evaluation of these methods is often realized in a retrospective way, notably by studying the enrichment of benchmarking data sets. To this purpose, numerous benchmarking data sets were developed over the years, and the resulting improvements led to the availability of high quality benchmarking data sets. However, some points still have to be considered in the selection of the active compounds, decoys, and protein structures to obtain optimal benchmarking data sets.

The KMAT: Benchmarking Knowledge Management.

ERIC Educational Resources Information Center

de Jager, Martha

Provides an overview of knowledge management and benchmarking, including the benefits and methods of benchmarking (e.g., competitive, cooperative, collaborative, and internal benchmarking). Arthur Andersen's KMAT (Knowledge Management Assessment Tool) is described. The KMAT is a collaborative benchmarking tool, designed to help organizations make…

Benchmarking the x-ray phase contrast imaging for ICF DT ice characterization using roughened surrogates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dewald, E; Kozioziemski, B; Moody, J

2008-06-26

We use x-ray phase contrast imaging to characterize the inner surface roughness of DT ice layers in capsules planned for future ignition experiments. It is therefore important to quantify how well the x-ray data correlates with the actual ice roughness. We benchmarked the accuracy of our system using surrogates with fabricated roughness characterized with high precision standard techniques. Cylindrical artifacts with azimuthally uniform sinusoidal perturbations with 100 um period and 1 um amplitude demonstrated 0.02 um accuracy limited by the resolution of the imager and the source size of our phase contrast system. Spherical surrogates with random roughness close tomore » that required for the DT ice for a successful ignition experiment were used to correlate the actual surface roughness to that obtained from the x-ray measurements. When comparing average power spectra of individual measurements, the accuracy mode number limits of the x-ray phase contrast system benchmarked against surface characterization performed by Atomic Force Microscopy are 60 and 90 for surrogates smoother and rougher than the required roughness for the ice. These agreement mode number limits are >100 when comparing matching individual measurements. We will discuss the implications for interpreting DT ice roughness data derived from phase-contrast x-ray imaging.« less

Benchmarking of HEU Mental Annuli Critical Assemblies with Internally Reflected Graphite Cylinder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiaobo, Liu; Bess, John D.; Marshall, Margaret A.

Three experimental configurations of critical assemblies, performed in 1963 at the Oak Ridge Critical Experiment Facility, which are assembled using three different diameter HEU annuli (15-9 inches, 15-7 inches and 13-7 inches) metal annuli with internally reflected graphite cylinder are evaluated and benchmarked. The experimental uncertainties which are 0.00055, 0.00055 and 0.00055 respectively, and biases to the detailed benchmark models which are -0.00179, -0.00189 and -0.00114 respectively, were determined, and the experimental benchmark keff results were obtained for both detailed and simplified model. The calculation results for both detailed and simplified models using MCNP6-1.0 and ENDF VII.1 agree well tomore » the benchmark experimental results with a difference of less than 0.2%. These are acceptable benchmark experiments for inclusion in the ICSBEP Handbook.« less

Benchmarks for target tracking

NASA Astrophysics Data System (ADS)

Dunham, Darin T.; West, Philip D.

2011-09-01

The term benchmark originates from the chiseled horizontal marks that surveyors made, into which an angle-iron could be placed to bracket ("bench") a leveling rod, thus ensuring that the leveling rod can be repositioned in exactly the same place in the future. A benchmark in computer terms is the result of running a computer program, or a set of programs, in order to assess the relative performance of an object by running a number of standard tests and trials against it. This paper will discuss the history of simulation benchmarks that are being used by multiple branches of the military and agencies of the US government. These benchmarks range from missile defense applications to chemical biological situations. Typically, a benchmark is used with Monte Carlo runs in order to tease out how algorithms deal with variability and the range of possible inputs. We will also describe problems that can be solved by a benchmark.

Subgroup Benchmark Calculations for the Intra-Pellet Nonuniform Temperature Cases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Kang Seog; Jung, Yeon Sang; Liu, Yuxuan

A benchmark suite has been developed by Seoul National University (SNU) for intrapellet nonuniform temperature distribution cases based on the practical temperature profiles according to the thermal power levels. Though a new subgroup capability for nonuniform temperature distribution was implemented in MPACT, no validation calculation has been performed for the new capability. This study focuses on bench-marking the new capability through a code-to-code comparison. Two continuous-energy Monte Carlo codes, McCARD and CE-KENO, are engaged in obtaining reference solutions, and the MPACT results are compared to the SNU nTRACER using a similar cross section library and subgroup method to obtain self-shieldedmore » cross sections.« less

Benchmarking and the laboratory

PubMed Central

Galloway, M; Nadin, L

2001-01-01

This article describes how benchmarking can be used to assess laboratory performance. Two benchmarking schemes are reviewed, the Clinical Benchmarking Company's Pathology Report and the College of American Pathologists' Q-Probes scheme. The Clinical Benchmarking Company's Pathology Report is undertaken by staff based in the clinical management unit, Keele University with appropriate input from the professional organisations within pathology. Five annual reports have now been completed. Each report is a detailed analysis of 10 areas of laboratory performance. In this review, particular attention is focused on the areas of quality, productivity, variation in clinical practice, skill mix, and working hours. The Q-Probes scheme is part of the College of American Pathologists programme in studies of quality assurance. The Q-Probes scheme and its applicability to pathology in the UK is illustrated by reviewing two recent Q-Probe studies: routine outpatient test turnaround time and outpatient test order accuracy. The Q-Probes scheme is somewhat limited by the small number of UK laboratories that have participated. In conclusion, as a result of the government's policy in the UK, benchmarking is here to stay. Benchmarking schemes described in this article are one way in which pathologists can demonstrate that they are providing a cost effective and high quality service. Key Words: benchmarking • pathology PMID:11477112

Benchmarking for Higher Education.

ERIC Educational Resources Information Center

Jackson, Norman, Ed.; Lund, Helen, Ed.

The chapters in this collection explore the concept of benchmarking as it is being used and developed in higher education (HE). Case studies and reviews show how universities in the United Kingdom are using benchmarking to aid in self-regulation and self-improvement. The chapters are: (1) "Introduction to Benchmarking" (Norman Jackson…

Overview of TPC Benchmark E: The Next Generation of OLTP Benchmarks

NASA Astrophysics Data System (ADS)

Hogan, Trish

Set to replace the aging TPC-C, the TPC Benchmark E is the next generation OLTP benchmark, which more accurately models client database usage. TPC-E addresses the shortcomings of TPC-C. It has a much more complex workload, requires the use of RAID-protected storage, generates much less I/O, and is much cheaper and easier to set up, run, and audit. After a period of overlap, it is expected that TPC-E will become the de facto OLTP benchmark.

Implementation of Benchmarking Transportation Logistics Practices and Future Benchmarking Organizations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thrower, A.W.; Patric, J.; Keister, M.

2008-07-01

The purpose of the Office of Civilian Radioactive Waste Management's (OCRWM) Logistics Benchmarking Project is to identify established government and industry practices for the safe transportation of hazardous materials which can serve as a yardstick for design and operation of OCRWM's national transportation system for shipping spent nuclear fuel and high-level radioactive waste to the proposed repository at Yucca Mountain, Nevada. The project will present logistics and transportation practices and develop implementation recommendations for adaptation by the national transportation system. This paper will describe the process used to perform the initial benchmarking study, highlight interim findings, and explain how thesemore » findings are being implemented. It will also provide an overview of the next phase of benchmarking studies. The benchmarking effort will remain a high-priority activity throughout the planning and operational phases of the transportation system. The initial phase of the project focused on government transportation programs to identify those practices which are most clearly applicable to OCRWM. These Federal programs have decades of safe transportation experience, strive for excellence in operations, and implement effective stakeholder involvement, all of which parallel OCRWM's transportation mission and vision. The initial benchmarking project focused on four business processes that are critical to OCRWM's mission success, and can be incorporated into OCRWM planning and preparation in the near term. The processes examined were: transportation business model, contract management/out-sourcing, stakeholder relations, and contingency planning. More recently, OCRWM examined logistics operations of AREVA NC's Business Unit Logistics in France. The next phase of benchmarking will focus on integrated domestic and international commercial radioactive logistic operations. The prospective companies represent large scale shippers and have vast

Benchmarking reference services: an introduction.

PubMed

Marshall, J G; Buchanan, H S

1995-01-01

Benchmarking is based on the common sense idea that someone else, either inside or outside of libraries, has found a better way of doing certain things and that your own library's performance can be improved by finding out how others do things and adopting the best practices you find. Benchmarking is one of the tools used for achieving continuous improvement in Total Quality Management (TQM) programs. Although benchmarking can be done on an informal basis, TQM puts considerable emphasis on formal data collection and performance measurement. Used to its full potential, benchmarking can provide a common measuring stick to evaluate process performance. This article introduces the general concept of benchmarking, linking it whenever possible to reference services in health sciences libraries. Data collection instruments that have potential application in benchmarking studies are discussed and the need to develop common measurement tools to facilitate benchmarking is emphasized.

Benchmarking in Academic Pharmacy Departments

PubMed Central

Chisholm-Burns, Marie; Nappi, Jean; Gubbins, Paul O.; Ross, Leigh Ann

2010-01-01

Benchmarking in academic pharmacy, and recommendations for the potential uses of benchmarking in academic pharmacy departments are discussed in this paper. Benchmarking is the process by which practices, procedures, and performance metrics are compared to an established standard or best practice. Many businesses and industries use benchmarking to compare processes and outcomes, and ultimately plan for improvement. Institutions of higher learning have embraced benchmarking practices to facilitate measuring the quality of their educational and research programs. Benchmarking is used internally as well to justify the allocation of institutional resources or to mediate among competing demands for additional program staff or space. Surveying all chairs of academic pharmacy departments to explore benchmarking issues such as department size and composition, as well as faculty teaching, scholarly, and service productivity, could provide valuable information. To date, attempts to gather this data have had limited success. We believe this information is potentially important, urge that efforts to gather it should be continued, and offer suggestions to achieve full participation. PMID:21179251

Benchmarking in academic pharmacy departments.

PubMed

Bosso, John A; Chisholm-Burns, Marie; Nappi, Jean; Gubbins, Paul O; Ross, Leigh Ann

2010-10-11

Benchmarking in academic pharmacy, and recommendations for the potential uses of benchmarking in academic pharmacy departments are discussed in this paper. Benchmarking is the process by which practices, procedures, and performance metrics are compared to an established standard or best practice. Many businesses and industries use benchmarking to compare processes and outcomes, and ultimately plan for improvement. Institutions of higher learning have embraced benchmarking practices to facilitate measuring the quality of their educational and research programs. Benchmarking is used internally as well to justify the allocation of institutional resources or to mediate among competing demands for additional program staff or space. Surveying all chairs of academic pharmacy departments to explore benchmarking issues such as department size and composition, as well as faculty teaching, scholarly, and service productivity, could provide valuable information. To date, attempts to gather this data have had limited success. We believe this information is potentially important, urge that efforts to gather it should be continued, and offer suggestions to achieve full participation.

Benchmarking: applications to transfusion medicine.

PubMed

Apelseth, Torunn Oveland; Molnar, Laura; Arnold, Emmy; Heddle, Nancy M

2012-10-01

Benchmarking is as a structured continuous collaborative process in which comparisons for selected indicators are used to identify factors that, when implemented, will improve transfusion practices. This study aimed to identify transfusion medicine studies reporting on benchmarking, summarize the benchmarking approaches used, and identify important considerations to move the concept of benchmarking forward in the field of transfusion medicine. A systematic review of published literature was performed to identify transfusion medicine-related studies that compared at least 2 separate institutions or regions with the intention of benchmarking focusing on 4 areas: blood utilization, safety, operational aspects, and blood donation. Forty-five studies were included: blood utilization (n = 35), safety (n = 5), operational aspects of transfusion medicine (n = 5), and blood donation (n = 0). Based on predefined criteria, 7 publications were classified as benchmarking, 2 as trending, and 36 as single-event studies. Three models of benchmarking are described: (1) a regional benchmarking program that collects and links relevant data from existing electronic sources, (2) a sentinel site model where data from a limited number of sites are collected, and (3) an institutional-initiated model where a site identifies indicators of interest and approaches other institutions. Benchmarking approaches are needed in the field of transfusion medicine. Major challenges include defining best practices and developing cost-effective methods of data collection. For those interested in initiating a benchmarking program, the sentinel site model may be most effective and sustainable as a starting point, although the regional model would be the ideal goal. Copyright © 2012 Elsevier Inc. All rights reserved.

Results Oriented Benchmarking: The Evolution of Benchmarking at NASA from Competitive Comparisons to World Class Space Partnerships

NASA Technical Reports Server (NTRS)

Bell, Michael A.

1999-01-01

Informal benchmarking using personal or professional networks has taken place for many years at the Kennedy Space Center (KSC). The National Aeronautics and Space Administration (NASA) recognized early on, the need to formalize the benchmarking process for better utilization of resources and improved benchmarking performance. The need to compete in a faster, better, cheaper environment has been the catalyst for formalizing these efforts. A pioneering benchmarking consortium was chartered at KSC in January 1994. The consortium known as the Kennedy Benchmarking Clearinghouse (KBC), is a collaborative effort of NASA and all major KSC contractors. The charter of this consortium is to facilitate effective benchmarking, and leverage the resulting quality improvements across KSC. The KBC acts as a resource with experienced facilitators and a proven process. One of the initial actions of the KBC was to develop a holistic methodology for Center-wide benchmarking. This approach to Benchmarking integrates the best features of proven benchmarking models (i.e., Camp, Spendolini, Watson, and Balm). This cost-effective alternative to conventional Benchmarking approaches has provided a foundation for consistent benchmarking at KSC through the development of common terminology, tools, and techniques. Through these efforts a foundation and infrastructure has been built which allows short duration benchmarking studies yielding results gleaned from world class partners that can be readily implemented. The KBC has been recognized with the Silver Medal Award (in the applied research category) from the International Benchmarking Clearinghouse.

FireHose Streaming Benchmarks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karl Anderson, Steve Plimpton

2015-01-27

The FireHose Streaming Benchmarks are a suite of stream-processing benchmarks defined to enable comparison of streaming software and hardware, both quantitatively vis-a-vis the rate at which they can process data, and qualitatively by judging the effort involved to implement and run the benchmarks. Each benchmark has two parts. The first is a generator which produces and outputs datums at a high rate in a specific format. The second is an analytic which reads the stream of datums and is required to perform a well-defined calculation on the collection of datums, typically to find anomalous datums that have been created inmore » the stream by the generator. The FireHose suite provides code for the generators, sample code for the analytics (which users are free to re-implement in their own custom frameworks), and a precise definition of each benchmark calculation.« less

Self-consistent assessment of Englert-Schwinger model on atomic properties

NASA Astrophysics Data System (ADS)

Lehtomäki, Jouko; Lopez-Acevedo, Olga

2017-12-01

Our manuscript investigates a self-consistent solution of the statistical atom model proposed by Berthold-Georg Englert and Julian Schwinger (the ES model) and benchmarks it against atomic Kohn-Sham and two orbital-free models of the Thomas-Fermi-Dirac (TFD)-λvW family. Results show that the ES model generally offers the same accuracy as the well-known TFD-1/5 vW model; however, the ES model corrects the failure in the Pauli potential near-nucleus region. We also point to the inability of describing low-Z atoms as the foremost concern in improving the present model.

Self-consistent assessment of Englert-Schwinger model on atomic properties.

PubMed

Lehtomäki, Jouko; Lopez-Acevedo, Olga

2017-12-21

Our manuscript investigates a self-consistent solution of the statistical atom model proposed by Berthold-Georg Englert and Julian Schwinger (the ES model) and benchmarks it against atomic Kohn-Sham and two orbital-free models of the Thomas-Fermi-Dirac (TFD)-λvW family. Results show that the ES model generally offers the same accuracy as the well-known TFD-15vW model; however, the ES model corrects the failure in the Pauli potential near-nucleus region. We also point to the inability of describing low-Z atoms as the foremost concern in improving the present model.

GAPD: a GPU-accelerated atom-based polychromatic diffraction simulation code.

PubMed

E, J C; Wang, L; Chen, S; Zhang, Y Y; Luo, S N

2018-03-01

GAPD, a graphics-processing-unit (GPU)-accelerated atom-based polychromatic diffraction simulation code for direct, kinematics-based, simulations of X-ray/electron diffraction of large-scale atomic systems with mono-/polychromatic beams and arbitrary plane detector geometries, is presented. This code implements GPU parallel computation via both real- and reciprocal-space decompositions. With GAPD, direct simulations are performed of the reciprocal lattice node of ultralarge systems (∼5 billion atoms) and diffraction patterns of single-crystal and polycrystalline configurations with mono- and polychromatic X-ray beams (including synchrotron undulator sources), and validation, benchmark and application cases are presented.

All-Atom Four-Body Knowledge-Based Statistical Potentials to Distinguish Native Protein Structures from Nonnative Folds

PubMed Central

2017-01-01

Recent advances in understanding protein folding have benefitted from coarse-grained representations of protein structures. Empirical energy functions derived from these techniques occasionally succeed in distinguishing native structures from their corresponding ensembles of nonnative folds or decoys which display varying degrees of structural dissimilarity to the native proteins. Here we utilized atomic coordinates of single protein chains, comprising a large diverse training set, to develop and evaluate twelve all-atom four-body statistical potentials obtained by exploring alternative values for a pair of inherent parameters. Delaunay tessellation was performed on the atomic coordinates of each protein to objectively identify all quadruplets of interacting atoms, and atomic potentials were generated via statistical analysis of the data and implementation of the inverted Boltzmann principle. Our potentials were evaluated using benchmarking datasets from Decoys-‘R'-Us, and comparisons were made with twelve other physics- and knowledge-based potentials. Ranking 3rd, our best potential tied CHARMM19 and surpassed AMBER force field potentials. We illustrate how a generalized version of our potential can be used to empirically calculate binding energies for target-ligand complexes, using HIV-1 protease-inhibitor complexes for a practical application. The combined results suggest an accurate and efficient atomic four-body statistical potential for protein structure prediction and assessment. PMID:29119109

Benchmark Evaluation of Dounreay Prototype Fast Reactor Minor Actinide Depletion Measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hess, J. D.; Gauld, I. C.; Gulliford, J.

2017-01-01

Historic measurements of actinide samples in the Dounreay Prototype Fast Reactor (PFR) are of interest for modern nuclear data and simulation validation. Samples of various higher-actinide isotopes were irradiated for 492 effective full-power days and radiochemically assayed at Oak Ridge National Laboratory (ORNL) and Japan Atomic Energy Research Institute (JAERI). Limited data were available regarding the PFR irradiation; a six-group neutron spectra was available with some power history data to support a burnup depletion analysis validation study. Under the guidance of the Organisation for Economic Co-Operation and Development Nuclear Energy Agency (OECD NEA), the International Reactor Physics Experiment Evaluation Projectmore » (IRPhEP) and Spent Fuel Isotopic Composition (SFCOMPO) Project are collaborating to recover all measurement data pertaining to these measurements, including collaboration with the United Kingdom to obtain pertinent reactor physics design and operational history data. These activities will produce internationally peer-reviewed benchmark data to support validation of minor actinide cross section data and modern neutronic simulation of fast reactors with accompanying fuel cycle activities such as transportation, recycling, storage, and criticality safety.« less

Benchmark cool companions: ages and abundances for the PZ Telescopii system

NASA Astrophysics Data System (ADS)

Jenkins, J. S.; Pavlenko, Y. V.; Ivanyuk, O.; Gallardo, J.; Jones, M. I.; Day-Jones, A. C.; Jones, H. R. A.; Ruiz, M. T.; Pinfield, D. J.; Yakovina, L.

2012-03-01

We present new ages and abundance measurements for the pre-main-sequence star PZ Telescopii (more commonly known as PZ Tel). PZ Tel was recently found to host a young and low-mass companion. Such companions, whether they are brown dwarfs or planetary systems, can attain benchmark status by detailed study of the properties of the primary, and then evolutionary and bulk characteristics can be inferred for the companion. Using Fibre-fed Extended Range Optical Spectrograph spectra, we have measured atomic abundances (e.g. Fe and Li) and chromospheric activity for PZ Tel and used these to obtain the metallicity and age estimates for the companion. We have also determined the age independently using the latest evolutionary models. We find PZ Tel A to be a rapidly rotating (v sin i= 73 ± 5 km s-1), approximately solar metallicity star [log N(Fe) =-4.37 ± 0.06 dex or [Fe/H] = 0.05 ± 0.20 dex]. We measure a non-local thermodynamic equilibrium lithium abundance of log N(Li) = 3.1 ± 0.1 dex, which from depletion models gives rise to an age of 7? Myr for the system. Our measured chromospheric activity (? of -4.12) returns an age of 26 ± 2 Myr, as does fitting pre-main-sequence evolutionary tracks (τevol= 22 ± 3 Myr), both of these are in disagreement with the lithium age. We speculate on reasons for this difference and introduce new models for lithium depletion that incorporate both rotation and magnetic field effects. We also synthesize solar, metal-poor and metal-rich substellar evolutionary models to better determine the bulk properties of PZ Tel B, showing that PZ Tel B is probably more massive than previous estimates, meaning the companion is not a giant exoplanet, even though a planetary-like formation origin can go some way to describing the distribution of benchmark binaries currently known. We show how PZ Tel B compares to other currently known age and metallicity benchmark systems and try to empirically test the effects of dust opacity as a function of

Benchmark quality total atomization energies of small polyatomic molecules

NASA Astrophysics Data System (ADS)

Martin, Jan M. L.; Taylor, Peter R.

1997-05-01

Successive coupled-cluster [CCSD(T)] calculations in basis sets of spdf, spdfg, and spdfgh quality, combined with separate Schwartz-type extrapolations A+B/(l+1/2)α of the self-consistent field (SCF) and correlation energies, permit the calculations of molecular total atomization energies (TAEs) with a mean absolute error of as low as 0.12 kcal/mol. For the largest molecule treated, C2H4, we find ∑D0=532.0 kcal/mol, in perfect agreement with experiment. The aug-cc-pV5Z basis set recovers on average about 99% of the valence correlation contribution to the TAE, and essentially the entire SCF contribution.

Using chemical benchmarking to determine the persistence of chemicals in a Swedish lake.

PubMed

Zou, Hongyan; Radke, Michael; Kierkegaard, Amelie; MacLeod, Matthew; McLachlan, Michael S

2015-02-03

It is challenging to measure the persistence of chemicals under field conditions. In this work, two approaches for measuring persistence in the field were compared: the chemical mass balance approach, and a novel chemical benchmarking approach. Ten pharmaceuticals, an X-ray contrast agent, and an artificial sweetener were studied in a Swedish lake. Acesulfame K was selected as a benchmark to quantify persistence using the chemical benchmarking approach. The 95% confidence intervals of the half-life for transformation in the lake system ranged from 780-5700 days for carbamazepine to <1-2 days for ketoprofen. The persistence estimates obtained using the benchmarking approach agreed well with those from the mass balance approach (1-21% difference), indicating that chemical benchmarking can be a valid and useful method to measure the persistence of chemicals under field conditions. Compared to the mass balance approach, the benchmarking approach partially or completely eliminates the need to quantify mass flow of chemicals, so it is particularly advantageous when the quantification of mass flow of chemicals is difficult. Furthermore, the benchmarking approach allows for ready comparison and ranking of the persistence of different chemicals.

Benchmarking, benchmarks, or best practices? Applying quality improvement principles to decrease surgical turnaround time.

PubMed

Mitchell, L

1996-01-01

The processes of benchmarking, benchmark data comparative analysis, and study of best practices are distinctly different. The study of best practices is explained with an example based on the Arthur Andersen & Co. 1992 "Study of Best Practices in Ambulatory Surgery". The results of a national best practices study in ambulatory surgery were used to provide our quality improvement team with the goal of improving the turnaround time between surgical cases. The team used a seven-step quality improvement problem-solving process to improve the surgical turnaround time. The national benchmark for turnaround times between surgical cases in 1992 was 13.5 minutes. The initial turnaround time at St. Joseph's Medical Center was 19.9 minutes. After the team implemented solutions, the time was reduced to an average of 16.3 minutes, an 18% improvement. Cost-benefit analysis showed a potential enhanced revenue of approximately $300,000, or a potential savings of $10,119. Applying quality improvement principles to benchmarking, benchmarks, or best practices can improve process performance. Understanding which form of benchmarking the institution wishes to embark on will help focus a team and use appropriate resources. Communicating with professional organizations that have experience in benchmarking will save time and money and help achieve the desired results.

Benchmarking Diagnostic Algorithms on an Electrical Power System Testbed

NASA Technical Reports Server (NTRS)

Kurtoglu, Tolga; Narasimhan, Sriram; Poll, Scott; Garcia, David; Wright, Stephanie

2009-01-01

Diagnostic algorithms (DAs) are key to enabling automated health management. These algorithms are designed to detect and isolate anomalies of either a component or the whole system based on observations received from sensors. In recent years a wide range of algorithms, both model-based and data-driven, have been developed to increase autonomy and improve system reliability and affordability. However, the lack of support to perform systematic benchmarking of these algorithms continues to create barriers for effective development and deployment of diagnostic technologies. In this paper, we present our efforts to benchmark a set of DAs on a common platform using a framework that was developed to evaluate and compare various performance metrics for diagnostic technologies. The diagnosed system is an electrical power system, namely the Advanced Diagnostics and Prognostics Testbed (ADAPT) developed and located at the NASA Ames Research Center. The paper presents the fundamentals of the benchmarking framework, the ADAPT system, description of faults and data sets, the metrics used for evaluation, and an in-depth analysis of benchmarking results obtained from testing ten diagnostic algorithms on the ADAPT electrical power system testbed.

Comparing the accuracy of high-dimensional neural network potentials and the systematic molecular fragmentation method: A benchmark study for all-trans alkanes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gastegger, Michael; Kauffmann, Clemens; Marquetand, Philipp, E-mail: philipp.marquetand@univie.ac.at

Many approaches, which have been developed to express the potential energy of large systems, exploit the locality of the atomic interactions. A prominent example is the fragmentation methods in which the quantum chemical calculations are carried out for overlapping small fragments of a given molecule that are then combined in a second step to yield the system’s total energy. Here we compare the accuracy of the systematic molecular fragmentation approach with the performance of high-dimensional neural network (HDNN) potentials introduced by Behler and Parrinello. HDNN potentials are similar in spirit to the fragmentation approach in that the total energy ismore » constructed as a sum of environment-dependent atomic energies, which are derived indirectly from electronic structure calculations. As a benchmark set, we use all-trans alkanes containing up to eleven carbon atoms at the coupled cluster level of theory. These molecules have been chosen because they allow to extrapolate reliable reference energies for very long chains, enabling an assessment of the energies obtained by both methods for alkanes including up to 10 000 carbon atoms. We find that both methods predict high-quality energies with the HDNN potentials yielding smaller errors with respect to the coupled cluster reference.« less

78 FR 47671 - Proposed Information Collection; Comment Request; Benchmark Survey of Insurance Transactions by U...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-06

... Request; Benchmark Survey of Insurance Transactions by U.S. Insurance Companies with Foreign Persons...: I. Abstract Form BE-140, Benchmark Survey of Insurance Transactions by U.S. Insurance Companies with Foreign Persons, obtains annual data from all U.S. insurance companies that engage in the following...

Benchmarking Using Basic DBMS Operations

NASA Astrophysics Data System (ADS)

Crolotte, Alain; Ghazal, Ahmad

The TPC-H benchmark proved to be successful in the decision support area. Many commercial database vendors and their related hardware vendors used these benchmarks to show the superiority and competitive edge of their products. However, over time, the TPC-H became less representative of industry trends as vendors keep tuning their database to this benchmark-specific workload. In this paper, we present XMarq, a simple benchmark framework that can be used to compare various software/hardware combinations. Our benchmark model is currently composed of 25 queries that measure the performance of basic operations such as scans, aggregations, joins and index access. This benchmark model is based on the TPC-H data model due to its maturity and well-understood data generation capability. We also propose metrics to evaluate single-system performance and compare two systems. Finally we illustrate the effectiveness of this model by showing experimental results comparing two systems under different conditions.

The theoretical current-voltage dependence of a non-degenerate disordered organic material obtained with conductive atomic force microscopy

NASA Astrophysics Data System (ADS)

Woellner, Cristiano F.; Freire, José A.; Guide, Michele; Nguyen, Thuc-Quyen

2011-08-01

We develop a simple continuum model for the current voltage characteristics of a material as measured by the conducting atomic force microscopy, including space charge effects. We address the effect of the point contact on the magnitude of the current and on the transition voltages between the different current regimes by comparing these with the corresponding expressions obtained with planar electrodes.

Benchmarking Tool Kit.

ERIC Educational Resources Information Center

Canadian Health Libraries Association.

Nine Canadian health libraries participated in a pilot test of the Benchmarking Tool Kit between January and April, 1998. Although the Tool Kit was designed specifically for health libraries, the content and approach are useful to other types of libraries as well. Used to its full potential, benchmarking can provide a common measuring stick to…

Atomic masses 1993. The 1993 atomic mass evaluation

NASA Astrophysics Data System (ADS)

Audi, G.; Wapstra, A. H.

1993-11-01

The 1993 atomic mass evaluation by G. Audi and A.H. Wapstra is documented. The resulting data files containing recommended values of atomic masses, obtained by experiment of systematics, and related data such as reaction and separation energies are described. The data files can be obtained through online services from several nuclear data centers or on magnetic tape, free of charge.

The Isprs Benchmark on Indoor Modelling

NASA Astrophysics Data System (ADS)

Khoshelham, K.; Díaz Vilariño, L.; Peter, M.; Kang, Z.; Acharya, D.

2017-09-01

Automated generation of 3D indoor models from point cloud data has been a topic of intensive research in recent years. While results on various datasets have been reported in literature, a comparison of the performance of different methods has not been possible due to the lack of benchmark datasets and a common evaluation framework. The ISPRS benchmark on indoor modelling aims to address this issue by providing a public benchmark dataset and an evaluation framework for performance comparison of indoor modelling methods. In this paper, we present the benchmark dataset comprising several point clouds of indoor environments captured by different sensors. We also discuss the evaluation and comparison of indoor modelling methods based on manually created reference models and appropriate quality evaluation criteria. The benchmark dataset is available for download at: benchmark-on-indoor-modelling.html"target="_blank">http://www2.isprs.org/commissions/comm4/wg5/benchmark-on-indoor-modelling.html.

Quantified Differentiation of Surface Topography for Nano-materials As-Obtained from Atomic Force Microscopy Images

NASA Astrophysics Data System (ADS)

Gupta, Mousumi; Chatterjee, Somenath

2018-04-01

Surface texture is an important issue to realize the nature (crest and trough) of surfaces. Atomic force microscopy (AFM) image is a key analysis for surface topography. However, in nano-scale, the nature (i.e., deflection or crack) as well as quantification (i.e., height or depth) of deposited layers is essential information for material scientist. In this paper, a gradient-based K-means algorithm is used to differentiate the layered surfaces depending on their color contrast of as-obtained from AFM images. A transformation using wavelet decomposition is initiated to extract the information about deflection or crack on the material surfaces from the same images. Z-axis depth analysis from wavelet coefficients provides information about the crack present in the material. Using the above method corresponding surface information for the material is obtained. In addition, the Gaussian filter is applied to remove the unwanted lines, which occurred during AFM scanning. Few known samples are taken as input, and validity of the above approaches is shown.

Development and Application of Benchmark Examples for Mode II Static Delamination Propagation and Fatigue Growth Predictions

NASA Technical Reports Server (NTRS)

Krueger, Ronald

2011-01-01

The development of benchmark examples for static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of an End-Notched Flexure (ENF) specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, static benchmark examples were created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall the results are encouraging, but further assessment for mixed-mode delamination is required.

Developing Benchmarks for Solar Radio Bursts

NASA Astrophysics Data System (ADS)

Biesecker, D. A.; White, S. M.; Gopalswamy, N.; Black, C.; Domm, P.; Love, J. J.; Pierson, J.

2016-12-01

Solar radio bursts can interfere with radar, communication, and tracking signals. In severe cases, radio bursts can inhibit the successful use of radio communications and disrupt a wide range of systems that are reliant on Position, Navigation, and Timing services on timescales ranging from minutes to hours across wide areas on the dayside of Earth. The White House's Space Weather Action Plan has asked for solar radio burst intensity benchmarks for an event occurrence frequency of 1 in 100 years and also a theoretical maximum intensity benchmark. The solar radio benchmark team was also asked to define the wavelength/frequency bands of interest. The benchmark team developed preliminary (phase 1) benchmarks for the VHF (30-300 MHz), UHF (300-3000 MHz), GPS (1176-1602 MHz), F10.7 (2800 MHz), and Microwave (4000-20000) bands. The preliminary benchmarks were derived based on previously published work. Limitations in the published work will be addressed in phase 2 of the benchmark process. In addition, deriving theoretical maxima requires additional work, where it is even possible to, in order to meet the Action Plan objectives. In this presentation, we will present the phase 1 benchmarks and the basis used to derive them. We will also present the work that needs to be done in order to complete the final, or phase 2 benchmarks.

CompaRNA: a server for continuous benchmarking of automated methods for RNA secondary structure prediction

PubMed Central

Puton, Tomasz; Kozlowski, Lukasz P.; Rother, Kristian M.; Bujnicki, Janusz M.

2013-01-01

We present a continuous benchmarking approach for the assessment of RNA secondary structure prediction methods implemented in the CompaRNA web server. As of 3 October 2012, the performance of 28 single-sequence and 13 comparative methods has been evaluated on RNA sequences/structures released weekly by the Protein Data Bank. We also provide a static benchmark generated on RNA 2D structures derived from the RNAstrand database. Benchmarks on both data sets offer insight into the relative performance of RNA secondary structure prediction methods on RNAs of different size and with respect to different types of structure. According to our tests, on the average, the most accurate predictions obtained by a comparative approach are generated by CentroidAlifold, MXScarna, RNAalifold and TurboFold. On the average, the most accurate predictions obtained by single-sequence analyses are generated by CentroidFold, ContextFold and IPknot. The best comparative methods typically outperform the best single-sequence methods if an alignment of homologous RNA sequences is available. This article presents the results of our benchmarks as of 3 October 2012, whereas the rankings presented online are continuously updated. We will gladly include new prediction methods and new measures of accuracy in the new editions of CompaRNA benchmarks. PMID:23435231

Benchmarking Multilayer-HySEA model for landslide generated tsunami. HTHMP validation process.

NASA Astrophysics Data System (ADS)

Macias, J.; Escalante, C.; Castro, M. J.

2017-12-01

Landslide tsunami hazard may be dominant along significant parts of the coastline around the world, in particular in the USA, as compared to hazards from other tsunamigenic sources. This fact motivated NTHMP about the need of benchmarking models for landslide generated tsunamis, following the same methodology already used for standard tsunami models when the source is seismic. To perform the above-mentioned validation process, a set of candidate benchmarks were proposed. These benchmarks are based on a subset of available laboratory data sets for solid slide experiments and deformable slide experiments, and include both submarine and subaerial slides. A benchmark based on a historic field event (Valdez, AK, 1964) close the list of proposed benchmarks. A total of 7 benchmarks. The Multilayer-HySEA model including non-hydrostatic effects has been used to perform all the benchmarking problems dealing with laboratory experiments proposed in the workshop that was organized at Texas A&M University - Galveston, on January 9-11, 2017 by NTHMP. The aim of this presentation is to show some of the latest numerical results obtained with the Multilayer-HySEA (non-hydrostatic) model in the framework of this validation effort.Acknowledgements. This research has been partially supported by the Spanish Government Research project SIMURISK (MTM2015-70490-C02-01-R) and University of Malaga, Campus de Excelencia Internacional Andalucía Tech. The GPU computations were performed at the Unit of Numerical Methods (University of Malaga).

Generation IV benchmarking of TRISO fuel performance models under accident conditions: Modeling input data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collin, Blaise P.

2014-09-01

This document presents the benchmark plan for the calculation of particle fuel performance on safety testing experiments that are representative of operational accidental transients. The benchmark is dedicated to the modeling of fission product release under accident conditions by fuel performance codes from around the world, and the subsequent comparison to post-irradiation experiment (PIE) data from the modeled heating tests. The accident condition benchmark is divided into three parts: the modeling of a simplified benchmark problem to assess potential numerical calculation issues at low fission product release; the modeling of the AGR-1 and HFR-EU1bis safety testing experiments; and, the comparisonmore » of the AGR-1 and HFR-EU1bis modeling results with PIE data. The simplified benchmark case, thereafter named NCC (Numerical Calculation Case), is derived from ''Case 5'' of the International Atomic Energy Agency (IAEA) Coordinated Research Program (CRP) on coated particle fuel technology [IAEA 2012]. It is included so participants can evaluate their codes at low fission product release. ''Case 5'' of the IAEA CRP-6 showed large code-to-code discrepancies in the release of fission products, which were attributed to ''effects of the numerical calculation method rather than the physical model''[IAEA 2012]. The NCC is therefore intended to check if these numerical effects subsist. The first two steps imply the involvement of the benchmark participants with a modeling effort following the guidelines and recommendations provided by this document. The third step involves the collection of the modeling results by Idaho National Laboratory (INL) and the comparison of these results with the available PIE data. The objective of this document is to provide all necessary input data to model the benchmark cases, and to give some methodology guidelines and recommendations in order to make all results suitable for comparison with each other. The participants should read this

Atomic Data in X-Ray Astrophysics

NASA Technical Reports Server (NTRS)

Brickhouse, N. S.

2000-01-01

With the launches of the Chandra X-ray Observatory (CXO) and the X-ray Multimirror Mission (XMM) and the upcoming launch of the Japanese mission ASTRO-E, high resolution X-ray spectroscopy of cosmic sources has begun. Early, deep observations of three stellar coronal sources will provide not only invaluable calibration data, but will also give us benchmarks for the atomic data under collisional equilibrium conditions. Analysis of the Chandra X-ray Observatory data, and data from other telescopes taken simultaneously, for these stars is ongoing as part of the Emission Line Project. Goals of the Emission Line Project are: (1) to determine and verify accurate and robust diagnostics and (2) to identify and prioritize issues in fundamental spectroscopy which will require further theoretical and/or laboratory work. The Astrophysical Plasma Emission Database will be described in some detail, as it is introducing standardization and flexibility into X-ray spectral modeling. Spectral models of X-ray astrophysical plasmas can be generally classified as dominated by either collisional ionization or by X-ray photoionization. While the atomic data needs for spectral models under these two types of ionization are significantly different, there axe overlapping data needs, as I will describe. Early results from the Emission Line Project benchmarks are providing an invaluable starting place, but continuing work to improve the accuracy and completeness of atomic data is needed. Additionally, we consider the possibility that some sources will require that both collisional ionization and photoionization be taken into account, or that time-dependent ionization be considered. Thus plasma spectral models of general use need to be computed over a wide range of physical conditions.

Benchmarking expert system tools

NASA Technical Reports Server (NTRS)

Riley, Gary

1988-01-01

As part of its evaluation of new technologies, the Artificial Intelligence Section of the Mission Planning and Analysis Div. at NASA-Johnson has made timing tests of several expert system building tools. Among the production systems tested were Automated Reasoning Tool, several versions of OPS5, and CLIPS (C Language Integrated Production System), an expert system builder developed by the AI section. Also included in the test were a Zetalisp version of the benchmark along with four versions of the benchmark written in Knowledge Engineering Environment, an object oriented, frame based expert system tool. The benchmarks used for testing are studied.

Closed-Loop Neuromorphic Benchmarks

PubMed Central

Stewart, Terrence C.; DeWolf, Travis; Kleinhans, Ashley; Eliasmith, Chris

2015-01-01

Evaluating the effectiveness and performance of neuromorphic hardware is difficult. It is even more difficult when the task of interest is a closed-loop task; that is, a task where the output from the neuromorphic hardware affects some environment, which then in turn affects the hardware's future input. However, closed-loop situations are one of the primary potential uses of neuromorphic hardware. To address this, we present a methodology for generating closed-loop benchmarks that makes use of a hybrid of real physical embodiment and a type of “minimal” simulation. Minimal simulation has been shown to lead to robust real-world performance, while still maintaining the practical advantages of simulation, such as making it easy for the same benchmark to be used by many researchers. This method is flexible enough to allow researchers to explicitly modify the benchmarks to identify specific task domains where particular hardware excels. To demonstrate the method, we present a set of novel benchmarks that focus on motor control for an arbitrary system with unknown external forces. Using these benchmarks, we show that an error-driven learning rule can consistently improve motor control performance across a randomly generated family of closed-loop simulations, even when there are up to 15 interacting joints to be controlled. PMID:26696820

Theoretical chemical kinetic study of the H-atom abstraction reactions from aldehydes and acids by Ḣ atoms and ȮH, HȮ2, and ĊH3 radicals.

PubMed

Mendes, Jorge; Zhou, Chong-Wen; Curran, Henry J

2014-12-26

We have performed a systematic, theoretical chemical kinetic investigation of H atom abstraction by Ḣ atoms and ȮH, HȮ2, and ĊH3 radicals from aldehydes (methanal, ethanal, propanal, and isobutanal) and acids (methanoic acid, ethanoic acid, propanoic acid, and isobutanoic acid). The geometry optimizations and frequencies of all of the species in the reaction mechanisms of the title reactions were calculated using the MP2 method and the 6-311G(d,p) basis set. The one-dimensional hindered rotor treatment for reactants and transition states and the intrinsic reaction coordinate calculations were also determined at the MP2/6-311G(d,p) level of theory. For the reactions of methanal and methanoic acid with Ḣ atoms and ȮH, HȮ2, and ĊH3 radicals, the calculated relative electronic energies were obtained with the CCSD(T)/cc-pVXZ (where X = D, T, and Q) method and were extrapolated to the complete basis set limit. The electronic energies obtained with the CCSD(T)/cc-pVTZ method were benchmarked against the CCSD(T)/CBS energies and were found to be within 1 kcal mol(-1) of one another. Thus, the energies calculated using the less expensive CCSD(T)/cc-pVTZ method were used in all of the reaction mechanisms and in calculating our high-pressure limit rate constants for the title reactions. Rate constants were calculated using conventional transition state theory with an asymmetric Eckart tunneling correction, as implemented in Variflex. Herein, we report the individual and average rate constants, on a per H atom basis, and total rate constants in the temperature range 500-2000 K. We have compared some of our rate constant results to available experimental and theoretical data, and our results are generally in good agreement.

Spherical harmonic results for the 3D Kobayashi Benchmark suite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, P N; Chang, B; Hanebutte, U R

1999-03-02

Spherical harmonic solutions are presented for the Kobayashi benchmark suite. The results were obtained with Ardra, a scalable, parallel neutron transport code developed at Lawrence Livermore National Laboratory (LLNL). The calculations were performed on the IBM ASCI Blue-Pacific computer at LLNL.

Understanding the atomic-level Green-Kubo stress correlation function for a liquid through phonons in a model crystal

NASA Astrophysics Data System (ADS)

Levashov, V. A.

2014-11-01

In order to gain insight into the connection between the vibrational dynamics and the atomic-level Green-Kubo stress correlation function in liquids, we consider this connection in a model crystal instead. Of course, vibrational dynamics in liquids and crystals are quite different and it is not expected that the results obtained on a model crystal should be valid for liquids. However, these considerations provide a benchmark to which the results of the previous molecular dynamics simulations can be compared. Thus, assuming that vibrations are plane waves, we derive analytical expressions for the atomic-level stress correlation functions in the classical limit and analyze them. These results provide, in particular, a recipe for analysis of the atomic-level stress correlation functions in Fourier space and extraction of the wave-vector and frequency-dependent information. We also evaluate the energies of the atomic-level stresses. The energies obtained are significantly smaller than the energies previously determined in molecular dynamics simulations of several model liquids. This result suggests that the average energies of the atomic-level stresses in liquids and glasses are largely determined by the structural disorder. We discuss this result in the context of equipartition of the atomic-level stress energies. Analysis of the previously published data suggests that it is possible to speak about configurational and vibrational contributions to the average energies of the atomic-level stresses in a glass state. However, this separation in a liquid state is problematic. We also introduce and briefly consider the atomic-level transverse current correlation function. Finally, we address the broadening of the peaks in the pair distribution function with increase of distance. We find that the peaks' broadening (by ≈40 % ) occurs due to the transverse vibrational modes, while contribution from the longitudinal modes does not change with distance.

Research on computer systems benchmarking

NASA Technical Reports Server (NTRS)

Smith, Alan Jay (Principal Investigator)

1996-01-01

This grant addresses the topic of research on computer systems benchmarking and is more generally concerned with performance issues in computer systems. This report reviews work in those areas during the period of NASA support under this grant. The bulk of the work performed concerned benchmarking and analysis of CPUs, compilers, caches, and benchmark programs. The first part of this work concerned the issue of benchmark performance prediction. A new approach to benchmarking and machine characterization was reported, using a machine characterizer that measures the performance of a given system in terms of a Fortran abstract machine. Another report focused on analyzing compiler performance. The performance impact of optimization in the context of our methodology for CPU performance characterization was based on the abstract machine model. Benchmark programs are analyzed in another paper. A machine-independent model of program execution was developed to characterize both machine performance and program execution. By merging these machine and program characterizations, execution time can be estimated for arbitrary machine/program combinations. The work was continued into the domain of parallel and vector machines, including the issue of caches in vector processors and multiprocessors. All of the afore-mentioned accomplishments are more specifically summarized in this report, as well as those smaller in magnitude supported by this grant.

Simultaneous multielement atomic absorption spectrometry with graphite furnace atomization

NASA Astrophysics Data System (ADS)

Harnly, James M.; Miller-Ihli, Nancy J.; O'Haver, Thomas C.

The extended analytical range capability of a simultaneous multielement atomic absorption continuum source spectrometer (SIMAAC) was tested for furnace atomization with respect to the signal measurement mode (peak height and area), the atomization mode (from the wall or from a platform), and the temperature program mode (stepped or ramped atomization). These parameters were evaluated with respect to the shapes of the analytical curves, the detection limits, carry-over contamination and accuracy. Peak area measurements gave more linear calibration curves. Methods for slowing the atomization step heating rate, the use of a ramped temperature program or a platform, produced similar calibration curves and longer linear ranges than atomization with a stepped temperature program. Peak height detection limits were best using stepped atomization from the wall. Peak area detection limits for all atomization modes were similar. Carry-over contamination was worse for peak area than peak height, worse for ramped atomization than stepped atomization, and worse for atomization from a platform than from the wall. Accurate determinations (100 ± 12% for Ca, Cu, Fe, Mn, and Zn in National Bureau of Standards' Standard Reference Materials Bovine Liver 1577 and Rice Flour 1568 were obtained using peak area measurements with ramped atomization from the wall and stepped atomization from a platform. Only stepped atomization from a platform gave accurate recoveries for K. Accurate recoveries, 100 ± 10%, with precisions ranging from 1 to 36 % (standard deviation), were obtained for the determination of Al, Co, Cr, Fe, Mn, Mo, Ni. Pb, V and Zn in Acidified Waters (NBS SRM 1643 and 1643a) using stepped atomization from a platform.

Making Benchmark Testing Work

ERIC Educational Resources Information Center

Herman, Joan L.; Baker, Eva L.

2005-01-01

Many schools are moving to develop benchmark tests to monitor their students' progress toward state standards throughout the academic year. Benchmark tests can provide the ongoing information that schools need to guide instructional programs and to address student learning problems. The authors discuss six criteria that educators can use to…

Novel Antimicrobial Titanium Dioxide Nanotubes Obtained through a Combination of Atomic Layer Deposition and Electrospinning Technologies.

PubMed

López de Dicastillo, Carol; Patiño, Cristian; Galotto, María Jose; Palma, Juan Luis; Alburquenque, Daniela; Escrig, Juan

2018-02-24

The search for new antimicrobial substances has increased in recent years. Antimicrobial nanostructures are one of the most promising alternatives. In this work, titanium dioxide nanotubes were obtained by an atomic layer deposition (ALD) process over electrospun polyvinyl alcohol nanofibers (PVN) at different temperatures with the purpose of obtaining antimicrobial nanostructures with a high specific area. Electrospinning and ALD parameters were studied in order to obtain PVN with smallest diameter and highest deposition rate, respectively. Chamber temperature was a key factor during ALD process and an appropriate titanium dioxide deposition performance was achieved at 200 °C. Subsequently, thermal and morphological analysis by SEM and TEM microscopies revealed hollow nanotubes were obtained after calcination process at 600 °C. This temperature allowed complete polymer removal and influenced the resulting anatase crystallographic structure of titanium dioxide that positively affected their antimicrobial activities. X-ray analysis confirmed the change of titanium dioxide crystallographic structure from amorphous phase of deposited PVN to anatase crystalline structure of nanotubes. These new nanostructures with very large surface areas resulted in interesting antimicrobial properties against Gram-positive and Gram-negative bacteria. Titanium dioxide nanotubes presented the highest activity against Escherichia coli with 5 log cycles reduction at 200 μg/mL concentration.

Novel Antimicrobial Titanium Dioxide Nanotubes Obtained through a Combination of Atomic Layer Deposition and Electrospinning Technologies

PubMed Central

Patiño, Cristian; Galotto, María Jose; Palma, Juan Luis; Alburquenque, Daniela

2018-01-01

The search for new antimicrobial substances has increased in recent years. Antimicrobial nanostructures are one of the most promising alternatives. In this work, titanium dioxide nanotubes were obtained by an atomic layer deposition (ALD) process over electrospun polyvinyl alcohol nanofibers (PVN) at different temperatures with the purpose of obtaining antimicrobial nanostructures with a high specific area. Electrospinning and ALD parameters were studied in order to obtain PVN with smallest diameter and highest deposition rate, respectively. Chamber temperature was a key factor during ALD process and an appropriate titanium dioxide deposition performance was achieved at 200 °C. Subsequently, thermal and morphological analysis by SEM and TEM microscopies revealed hollow nanotubes were obtained after calcination process at 600 °C. This temperature allowed complete polymer removal and influenced the resulting anatase crystallographic structure of titanium dioxide that positively affected their antimicrobial activities. X-ray analysis confirmed the change of titanium dioxide crystallographic structure from amorphous phase of deposited PVN to anatase crystalline structure of nanotubes. These new nanostructures with very large surface areas resulted in interesting antimicrobial properties against Gram-positive and Gram-negative bacteria. Titanium dioxide nanotubes presented the highest activity against Escherichia coli with 5 log cycles reduction at 200 μg/mL concentration. PMID:29495318

HS06 Benchmark for an ARM Server

NASA Astrophysics Data System (ADS)

Kluth, Stefan

2014-06-01

We benchmarked an ARM cortex-A9 based server system with a four-core CPU running at 1.1 GHz. The system used Ubuntu 12.04 as operating system and the HEPSPEC 2006 (HS06) benchmarking suite was compiled natively with gcc-4.4 on the system. The benchmark was run for various settings of the relevant gcc compiler options. We did not find significant influence from the compiler options on the benchmark result. The final HS06 benchmark result is 10.4.

NAS Grid Benchmarks. 1.0

NASA Technical Reports Server (NTRS)

VanderWijngaart, Rob; Frumkin, Michael; Biegel, Bryan A. (Technical Monitor)

2002-01-01

We provide a paper-and-pencil specification of a benchmark suite for computational grids. It is based on the NAS (NASA Advanced Supercomputing) Parallel Benchmarks (NPB) and is called the NAS Grid Benchmarks (NGB). NGB problems are presented as data flow graphs encapsulating an instance of a slightly modified NPB task in each graph node, which communicates with other nodes by sending/receiving initialization data. Like NPB, NGB specifies several different classes (problem sizes). In this report we describe classes S, W, and A, and provide verification values for each. The implementor has the freedom to choose any language, grid environment, security model, fault tolerance/error correction mechanism, etc., as long as the resulting implementation passes the verification test and reports the turnaround time of the benchmark.

Performance of exchange-correlation functionals in density functional theory calculations for liquid metal: A benchmark test for sodium

NASA Astrophysics Data System (ADS)

Han, Jeong-Hwan; Oda, Takuji

2018-04-01

The performance of exchange-correlation functionals in density-functional theory (DFT) calculations for liquid metal has not been sufficiently examined. In the present study, benchmark tests of Perdew-Burke-Ernzerhof (PBE), Armiento-Mattsson 2005 (AM05), PBE re-parameterized for solids, and local density approximation (LDA) functionals are conducted for liquid sodium. The pair correlation function, equilibrium atomic volume, bulk modulus, and relative enthalpy are evaluated at 600 K and 1000 K. Compared with the available experimental data, the errors range from -11.2% to 0.0% for the atomic volume, from -5.2% to 22.0% for the bulk modulus, and from -3.5% to 2.5% for the relative enthalpy depending on the DFT functional. The generalized gradient approximation functionals are superior to the LDA functional, and the PBE and AM05 functionals exhibit the best performance. In addition, we assess whether the error tendency in liquid simulations is comparable to that in solid simulations, which would suggest that the atomic volume and relative enthalpy performances are comparable between solid and liquid states but that the bulk modulus performance is not. These benchmark test results indicate that the results of liquid simulations are significantly dependent on the exchange-correlation functional and that the DFT functional performance in solid simulations can be used to roughly estimate the performance in liquid simulations.

Performance of exchange-correlation functionals in density functional theory calculations for liquid metal: A benchmark test for sodium.

PubMed

Han, Jeong-Hwan; Oda, Takuji

2018-04-14

The performance of exchange-correlation functionals in density-functional theory (DFT) calculations for liquid metal has not been sufficiently examined. In the present study, benchmark tests of Perdew-Burke-Ernzerhof (PBE), Armiento-Mattsson 2005 (AM05), PBE re-parameterized for solids, and local density approximation (LDA) functionals are conducted for liquid sodium. The pair correlation function, equilibrium atomic volume, bulk modulus, and relative enthalpy are evaluated at 600 K and 1000 K. Compared with the available experimental data, the errors range from -11.2% to 0.0% for the atomic volume, from -5.2% to 22.0% for the bulk modulus, and from -3.5% to 2.5% for the relative enthalpy depending on the DFT functional. The generalized gradient approximation functionals are superior to the LDA functional, and the PBE and AM05 functionals exhibit the best performance. In addition, we assess whether the error tendency in liquid simulations is comparable to that in solid simulations, which would suggest that the atomic volume and relative enthalpy performances are comparable between solid and liquid states but that the bulk modulus performance is not. These benchmark test results indicate that the results of liquid simulations are significantly dependent on the exchange-correlation functional and that the DFT functional performance in solid simulations can be used to roughly estimate the performance in liquid simulations.

The Zoo, Benchmarks & You: How To Reach the Oregon State Benchmarks with Zoo Resources.

ERIC Educational Resources Information Center

2002

This document aligns Oregon state educational benchmarks and standards with Oregon Zoo resources. Benchmark areas examined include English, mathematics, science, social studies, and career and life roles. Brief descriptions of the programs offered by the zoo are presented. (SOE)

A Seafloor Benchmark for 3-dimensional Geodesy

NASA Astrophysics Data System (ADS)

Chadwell, C. D.; Webb, S. C.; Nooner, S. L.

2014-12-01

We have developed an inexpensive, permanent seafloor benchmark to increase the longevity of seafloor geodetic measurements. The benchmark provides a physical tie to the sea floor lasting for decades (perhaps longer) on which geodetic sensors can be repeatedly placed and removed with millimeter resolution. Global coordinates estimated with seafloor geodetic techniques will remain attached to the benchmark allowing for the interchange of sensors as they fail or become obsolete, or for the sensors to be removed and used elsewhere, all the while maintaining a coherent series of positions referenced to the benchmark. The benchmark has been designed to free fall from the sea surface with transponders attached. The transponder can be recalled via an acoustic command sent from the surface to release from the benchmark and freely float to the sea surface for recovery. The duration of the sensor attachment to the benchmark will last from a few days to a few years depending on the specific needs of the experiment. The recovered sensors are then available to be reused at other locations, or again at the same site in the future. Three pins on the sensor frame mate precisely and unambiguously with three grooves on the benchmark. To reoccupy a benchmark a Remotely Operated Vehicle (ROV) uses its manipulator arm to place the sensor pins into the benchmark grooves. In June 2014 we deployed four benchmarks offshore central Oregon. We used the ROV Jason to successfully demonstrate the removal and replacement of packages onto the benchmark. We will show the benchmark design and its operational capabilities. Presently models of megathrust slip within the Cascadia Subduction Zone (CSZ) are mostly constrained by the sub-aerial GPS vectors from the Plate Boundary Observatory, a part of Earthscope. More long-lived seafloor geodetic measures are needed to better understand the earthquake and tsunami risk associated with a large rupture of the thrust fault within the Cascadia subduction zone

The Concepts "Benchmarks and Benchmarking" Used in Education Planning: Teacher Education as Example

ERIC Educational Resources Information Center

Steyn, H. J.

2015-01-01

Planning in education is a structured activity that includes several phases and steps that take into account several kinds of information (Steyn, Steyn, De Waal & Wolhuter, 2002: 146). One of the sets of information that are usually considered is the (so-called) "benchmarks" and "benchmarking" regarding the focus of a…

Translational benchmark risk analysis

PubMed Central

Piegorsch, Walter W.

2010-01-01

Translational development – in the sense of translating a mature methodology from one area of application to another, evolving area – is discussed for the use of benchmark doses in quantitative risk assessment. Illustrations are presented with traditional applications of the benchmark paradigm in biology and toxicology, and also with risk endpoints that differ from traditional toxicological archetypes. It is seen that the benchmark approach can apply to a diverse spectrum of risk management settings. This suggests a promising future for this important risk-analytic tool. Extensions of the method to a wider variety of applications represent a significant opportunity for enhancing environmental, biomedical, industrial, and socio-economic risk assessments. PMID:20953283

ARC: An open-source library for calculating properties of alkali Rydberg atoms

NASA Astrophysics Data System (ADS)

Šibalić, N.; Pritchard, J. D.; Adams, C. S.; Weatherill, K. J.

2017-11-01

We present an object-oriented Python library for the computation of properties of highly-excited Rydberg states of alkali atoms. These include single-body effects such as dipole matrix elements, excited-state lifetimes (radiative and black-body limited) and Stark maps of atoms in external electric fields, as well as two-atom interaction potentials accounting for dipole and quadrupole coupling effects valid at both long and short range for arbitrary placement of the atomic dipoles. The package is cross-referenced to precise measurements of atomic energy levels and features extensive documentation to facilitate rapid upgrade or expansion by users. This library has direct application in the field of quantum information and quantum optics which exploit the strong Rydberg dipolar interactions for two-qubit gates, robust atom-light interfaces and simulating quantum many-body physics, as well as the field of metrology using Rydberg atoms as precise microwave electrometers. Program Files doi:http://dx.doi.org/10.17632/hm5n8w628c.1 Licensing provisions: BSD-3-Clause Programming language: Python 2.7 or 3.5, with C extension External Routines: NumPy [1], SciPy [1], Matplotlib [2] Nature of problem: Calculating atomic properties of alkali atoms including lifetimes, energies, Stark shifts and dipole-dipole interaction strengths using matrix elements evaluated from radial wavefunctions. Solution method: Numerical integration of radial Schrödinger equation to obtain atomic wavefunctions, which are then used to evaluate dipole matrix elements. Properties are calculated using second order perturbation theory or exact diagonalisation of the interaction Hamiltonian, yielding results valid even at large external fields or small interatomic separation. Restrictions: External electric field fixed to be parallel to quantisation axis. Supplementary material: Detailed documentation (.html), and Jupyter notebook with examples and benchmarking runs (.html and .ipynb). [1] T.E. Oliphant

Medical school benchmarking - from tools to programmes.

PubMed

Wilkinson, Tim J; Hudson, Judith N; Mccoll, Geoffrey J; Hu, Wendy C Y; Jolly, Brian C; Schuwirth, Lambert W T

2015-02-01

Benchmarking among medical schools is essential, but may result in unwanted effects. To apply a conceptual framework to selected benchmarking activities of medical schools. We present an analogy between the effects of assessment on student learning and the effects of benchmarking on medical school educational activities. A framework by which benchmarking can be evaluated was developed and applied to key current benchmarking activities in Australia and New Zealand. The analogy generated a conceptual framework that tested five questions to be considered in relation to benchmarking: what is the purpose? what are the attributes of value? what are the best tools to assess the attributes of value? what happens to the results? and, what is the likely "institutional impact" of the results? If the activities were compared against a blueprint of desirable medical graduate outcomes, notable omissions would emerge. Medical schools should benchmark their performance on a range of educational activities to ensure quality improvement and to assure stakeholders that standards are being met. Although benchmarking potentially has positive benefits, it could also result in perverse incentives with unforeseen and detrimental effects on learning if it is undertaken using only a few selected assessment tools.

HPC Analytics Support. Requirements for Uncertainty Quantification Benchmarks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paulson, Patrick R.; Purohit, Sumit; Rodriguez, Luke R.

2015-05-01

This report outlines techniques for extending benchmark generation products so they support uncertainty quantification by benchmarked systems. We describe how uncertainty quantification requirements can be presented to candidate analytical tools supporting SPARQL. We describe benchmark data sets for evaluating uncertainty quantification, as well as an approach for using our benchmark generator to produce data sets for generating benchmark data sets.

BENCHMARK DOSE TECHNICAL GUIDANCE DOCUMENT ...

EPA Pesticide Factsheets

The purpose of this document is to provide guidance for the Agency on the application of the benchmark dose approach in determining the point of departure (POD) for health effects data, whether a linear or nonlinear low dose extrapolation is used. The guidance includes discussion on computation of benchmark doses and benchmark concentrations (BMDs and BMCs) and their lower confidence limits, data requirements, dose-response analysis, and reporting requirements. This guidance is based on today's knowledge and understanding, and on experience gained in using this approach.

Issues in Benchmark Metric Selection

NASA Astrophysics Data System (ADS)

Crolotte, Alain

It is true that a metric can influence a benchmark but will esoteric metrics create more problems than they will solve? We answer this question affirmatively by examining the case of the TPC-D metric which used the much debated geometric mean for the single-stream test. We will show how a simple choice influenced the benchmark and its conduct and, to some extent, DBMS development. After examining other alternatives our conclusion is that the “real” measure for a decision-support benchmark is the arithmetic mean.

Benchmarking clinical photography services in the NHS.

PubMed

Arbon, Giles

2015-01-01

Benchmarking is used in services across the National Health Service (NHS) using various benchmarking programs. Clinical photography services do not have a program in place and services have to rely on ad hoc surveys of other services. A trial benchmarking exercise was undertaken with 13 services in NHS Trusts. This highlights valuable data and comparisons that can be used to benchmark and improve services throughout the profession.

Method and system for benchmarking computers

DOEpatents

Gustafson, John L.

1993-09-14

A testing system and method for benchmarking computer systems. The system includes a store containing a scalable set of tasks to be performed to produce a solution in ever-increasing degrees of resolution as a larger number of the tasks are performed. A timing and control module allots to each computer a fixed benchmarking interval in which to perform the stored tasks. Means are provided for determining, after completion of the benchmarking interval, the degree of progress through the scalable set of tasks and for producing a benchmarking rating relating to the degree of progress for each computer.

[Benchmarking in patient identification: An opportunity to learn].

PubMed

Salazar-de-la-Guerra, R M; Santotomás-Pajarrón, A; González-Prieto, V; Menéndez-Fraga, M D; Rocha Hurtado, C

To perform a benchmarking on the safe identification of hospital patients involved in "Club de las tres C" (Calidez, Calidad y Cuidados) in order to prepare a common procedure for this process. A descriptive study was conducted on the patient identification process in palliative care and stroke units in 5medium-stay hospitals. The following steps were carried out: Data collection from each hospital; organisation and data analysis, and preparation of a common procedure for this process. The data obtained for the safe identification of all stroke patients were: hospital 1 (93%), hospital 2 (93.1%), hospital 3 (100%), and hospital 5 (93.4%), and for the palliative care process: hospital 1 (93%), hospital 2 (92.3%), hospital 3 (92%), hospital 4 (98.3%), and hospital 5 (85.2%). The aim of the study has been accomplished successfully. Benchmarking activities have been developed and knowledge on the patient identification process has been shared. All hospitals had good results. The hospital 3 was best in the ictus identification process. The benchmarking identification is difficult, but, a useful common procedure that collects the best practices has been identified among the 5 hospitals. Copyright © 2017 SECA. Publicado por Elsevier España, S.L.U. All rights reserved.

GEN-IV Benchmarking of Triso Fuel Performance Models under accident conditions modeling input data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collin, Blaise Paul

This document presents the benchmark plan for the calculation of particle fuel performance on safety testing experiments that are representative of operational accidental transients. The benchmark is dedicated to the modeling of fission product release under accident conditions by fuel performance codes from around the world, and the subsequent comparison to post-irradiation experiment (PIE) data from the modeled heating tests. The accident condition benchmark is divided into three parts: • The modeling of a simplified benchmark problem to assess potential numerical calculation issues at low fission product release. • The modeling of the AGR-1 and HFR-EU1bis safety testing experiments. •more » The comparison of the AGR-1 and HFR-EU1bis modeling results with PIE data. The simplified benchmark case, thereafter named NCC (Numerical Calculation Case), is derived from “Case 5” of the International Atomic Energy Agency (IAEA) Coordinated Research Program (CRP) on coated particle fuel technology [IAEA 2012]. It is included so participants can evaluate their codes at low fission product release. “Case 5” of the IAEA CRP-6 showed large code-to-code discrepancies in the release of fission products, which were attributed to “effects of the numerical calculation method rather than the physical model” [IAEA 2012]. The NCC is therefore intended to check if these numerical effects subsist. The first two steps imply the involvement of the benchmark participants with a modeling effort following the guidelines and recommendations provided by this document. The third step involves the collection of the modeling results by Idaho National Laboratory (INL) and the comparison of these results with the available PIE data. The objective of this document is to provide all necessary input data to model the benchmark cases, and to give some methodology guidelines and recommendations in order to make all results suitable for comparison with each other. The participants

All-atom four-body knowledge-based statistical potential to distinguish native tertiary RNA structures from nonnative folds.

PubMed

Masso, Majid

2018-09-14

Scientific breakthroughs in recent decades have uncovered the capability of RNA molecules to fulfill a wide array of structural, functional, and regulatory roles in living cells, leading to a concomitantly significant increase in both the number and diversity of experimentally determined RNA three-dimensional (3D) structures. Atomic coordinates from a representative training set of solved RNA structures, displaying low sequence and structure similarity, facilitate derivation of knowledge-based energy functions. Here we develop an all-atom four-body statistical potential and evaluate its capacity to distinguish native RNA 3D structures from nonnative folds based on calculated free energy scores. Atomic four-body nearest-neighbors are objectively identified by their occurrence as tetrahedral vertices in the Delaunay tessellations of RNA structures, and rates of atomic quadruplet interactions expected by chance are obtained from a multinomial reference distribution. Our four-body energy function, referred to as RAMP (ribonucleic acids multibody potential), is subsequently derived by applying the inverted Boltzmann principle to the frequency data, yielding an energy score for each type of atomic quadruplet interaction. Several well-known benchmark datasets reveal that RAMP is comparable with, and often outperforms, existing knowledge- and physics-based energy functions. To the best of our knowledge, this is the first study detailing an RNA tertiary structure-based multibody statistical potential and its comparative evaluation. Copyright © 2018 Elsevier Ltd. All rights reserved.

Benchmarking initiatives in the water industry.

PubMed

Parena, R; Smeets, E

2001-01-01

Customer satisfaction and service care are every day pushing professionals in the water industry to seek to improve their performance, lowering costs and increasing the provided service level. Process Benchmarking is generally recognised as a systematic mechanism of comparing one's own utility with other utilities or businesses with the intent of self-improvement by adopting structures or methods used elsewhere. The IWA Task Force on Benchmarking, operating inside the Statistics and Economics Committee, has been committed to developing a general accepted concept of Process Benchmarking to support water decision-makers in addressing issues of efficiency. In a first step the Task Force disseminated among the Committee members a questionnaire focused on providing suggestions about the kind, the evolution degree and the main concepts of Benchmarking adopted in the represented Countries. A comparison among the guidelines adopted in The Netherlands and Scandinavia has recently challenged the Task Force in drafting a methodology for a worldwide process benchmarking in water industry. The paper provides a framework of the most interesting benchmarking experiences in the water sector and describes in detail both the final results of the survey and the methodology focused on identification of possible improvement areas.

Benchmarking--Measuring and Comparing for Continuous Improvement.

ERIC Educational Resources Information Center

Henczel, Sue

2002-01-01

Discussion of benchmarking focuses on the use of internal and external benchmarking by special librarians. Highlights include defining types of benchmarking; historical development; benefits, including efficiency, improved performance, increased competitiveness, and better decision making; problems, including inappropriate adaptation; developing a…

EPA's Benchmark Dose Modeling Software

EPA Science Inventory

The EPA developed the Benchmark Dose Software (BMDS) as a tool to help Agency risk assessors facilitate applying benchmark dose (BMD) method’s to EPA’s human health risk assessment (HHRA) documents. The application of BMD methods overcomes many well know limitations ...

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 4 2012-10-01 2012-10-01 false Benchmark health benefits coverage. 440.330 Section 440.330 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...

ICSBEP Benchmarks For Nuclear Data Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Briggs, J. Blair

2005-05-24

The International Criticality Safety Benchmark Evaluation Project (ICSBEP) was initiated in 1992 by the United States Department of Energy. The ICSBEP became an official activity of the Organization for Economic Cooperation and Development (OECD) -- Nuclear Energy Agency (NEA) in 1995. Representatives from the United States, United Kingdom, France, Japan, the Russian Federation, Hungary, Republic of Korea, Slovenia, Serbia and Montenegro (formerly Yugoslavia), Kazakhstan, Spain, Israel, Brazil, Poland, and the Czech Republic are now participating. South Africa, India, China, and Germany are considering participation. The purpose of the ICSBEP is to identify, evaluate, verify, and formally document a comprehensive andmore » internationally peer-reviewed set of criticality safety benchmark data. The work of the ICSBEP is published as an OECD handbook entitled ''International Handbook of Evaluated Criticality Safety Benchmark Experiments.'' The 2004 Edition of the Handbook contains benchmark specifications for 3331 critical or subcritical configurations that are intended for use in validation efforts and for testing basic nuclear data. New to the 2004 Edition of the Handbook is a draft criticality alarm / shielding type benchmark that should be finalized in 2005 along with two other similar benchmarks. The Handbook is being used extensively for nuclear data testing and is expected to be a valuable resource for code and data validation and improvement efforts for decades to come. Specific benchmarks that are useful for testing structural materials such as iron, chromium, nickel, and manganese; beryllium; lead; thorium; and 238U are highlighted.« less

Benchmarking gate-based quantum computers

NASA Astrophysics Data System (ADS)

Michielsen, Kristel; Nocon, Madita; Willsch, Dennis; Jin, Fengping; Lippert, Thomas; De Raedt, Hans

2017-11-01

With the advent of public access to small gate-based quantum processors, it becomes necessary to develop a benchmarking methodology such that independent researchers can validate the operation of these processors. We explore the usefulness of a number of simple quantum circuits as benchmarks for gate-based quantum computing devices and show that circuits performing identity operations are very simple, scalable and sensitive to gate errors and are therefore very well suited for this task. We illustrate the procedure by presenting benchmark results for the IBM Quantum Experience, a cloud-based platform for gate-based quantum computing.

Directory of Useful Decoys, Enhanced (DUD-E): Better Ligands and Decoys for Better Benchmarking

PubMed Central

2012-01-01

A key metric to assess molecular docking remains ligand enrichment against challenging decoys. Whereas the directory of useful decoys (DUD) has been widely used, clear areas for optimization have emerged. Here we describe an improved benchmarking set that includes more diverse targets such as GPCRs and ion channels, totaling 102 proteins with 22886 clustered ligands drawn from ChEMBL, each with 50 property-matched decoys drawn from ZINC. To ensure chemotype diversity, we cluster each target’s ligands by their Bemis–Murcko atomic frameworks. We add net charge to the matched physicochemical properties and include only the most dissimilar decoys, by topology, from the ligands. An online automated tool (http://decoys.docking.org) generates these improved matched decoys for user-supplied ligands. We test this data set by docking all 102 targets, using the results to improve the balance between ligand desolvation and electrostatics in DOCK 3.6. The complete DUD-E benchmarking set is freely available at http://dude.docking.org. PMID:22716043

Performance of Landslide-HySEA tsunami model for NTHMP benchmarking validation process

NASA Astrophysics Data System (ADS)

Macias, Jorge

2017-04-01

In its FY2009 Strategic Plan, the NTHMP required that all numerical tsunami inundation models be verified as accurate and consistent through a model benchmarking process. This was completed in 2011, but only for seismic tsunami sources and in a limited manner for idealized solid underwater landslides. Recent work by various NTHMP states, however, has shown that landslide tsunami hazard may be dominant along significant parts of the US coastline, as compared to hazards from other tsunamigenic sources. To perform the above-mentioned validation process, a set of candidate benchmarks were proposed. These benchmarks are based on a subset of available laboratory date sets for solid slide experiments and deformable slide experiments, and include both submarine and subaerial slides. A benchmark based on a historic field event (Valdez, AK, 1964) close the list of proposed benchmarks. The Landslide-HySEA model has participated in the workshop that was organized at Texas A&M University - Galveston, on January 9-11, 2017. The aim of this presentation is to show some of the numerical results obtained for Landslide-HySEA in the framework of this benchmarking validation/verification effort. Acknowledgements. This research has been partially supported by the Junta de Andalucía research project TESELA (P11-RNM7069), the Spanish Government Research project SIMURISK (MTM2015-70490-C02-01-R) and Universidad de Málaga, Campus de Excelencia Internacional Andalucía Tech. The GPU computations were performed at the Unit of Numerical Methods (University of Malaga).

Conduction of molecular electronic devices: qualitative insights through atom-atom polarizabilities.

PubMed

Stuyver, T; Fias, S; De Proft, F; Fowler, P W; Geerlings, P

2015-03-07

The atom-atom polarizability and the transmission probability at the Fermi level, as obtained through the source-and-sink-potential method for every possible configuration of contacts simultaneously, are compared for polycyclic aromatic compounds. This comparison leads to the conjecture that a positive atom-atom polarizability is a necessary condition for transmission to take place in alternant hydrocarbons without non-bonding orbitals and that the relative transmission probability for different configurations of the contacts can be predicted by analyzing the corresponding atom-atom polarizability. A theoretical link between the two considered properties is derived, leading to a mathematical explanation for the observed trends for transmission based on the atom-atom polarizability.

Development of Benchmark Examples for Delamination Onset and Fatigue Growth Prediction

NASA Technical Reports Server (NTRS)

Krueger, Ronald

2011-01-01

An approach for assessing the delamination propagation and growth capabilities in commercial finite element codes was developed and demonstrated for the Virtual Crack Closure Technique (VCCT) implementations in ABAQUS. The Double Cantilever Beam (DCB) specimen was chosen as an example. First, benchmark results to assess delamination propagation capabilities under static loading were created using models simulating specimens with different delamination lengths. For each delamination length modeled, the load and displacement at the load point were monitored. The mixed-mode strain energy release rate components were calculated along the delamination front across the width of the specimen. A failure index was calculated by correlating the results with the mixed-mode failure criterion of the graphite/epoxy material. The calculated critical loads and critical displacements for delamination onset for each delamination length modeled were used as a benchmark. The load/displacement relationship computed during automatic propagation should closely match the benchmark case. Second, starting from an initially straight front, the delamination was allowed to propagate based on the algorithms implemented in the commercial finite element software. The load-displacement relationship obtained from the propagation analysis results and the benchmark results were compared. Good agreements could be achieved by selecting the appropriate input parameters, which were determined in an iterative procedure.

Machine characterization and benchmark performance prediction

NASA Technical Reports Server (NTRS)

Saavedra-Barrera, Rafael H.

1988-01-01

From runs of standard benchmarks or benchmark suites, it is not possible to characterize the machine nor to predict the run time of other benchmarks which have not been run. A new approach to benchmarking and machine characterization is reported. The creation and use of a machine analyzer is described, which measures the performance of a given machine on FORTRAN source language constructs. The machine analyzer yields a set of parameters which characterize the machine and spotlight its strong and weak points. Also described is a program analyzer, which analyzes FORTRAN programs and determines the frequency of execution of each of the same set of source language operations. It is then shown that by combining a machine characterization and a program characterization, we are able to predict with good accuracy the run time of a given benchmark on a given machine. Characterizations are provided for the Cray-X-MP/48, Cyber 205, IBM 3090/200, Amdahl 5840, Convex C-1, VAX 8600, VAX 11/785, VAX 11/780, SUN 3/50, and IBM RT-PC/125, and for the following benchmark programs or suites: Los Alamos (BMK8A1), Baskett, Linpack, Livermore Loops, Madelbrot Set, NAS Kernels, Shell Sort, Smith, Whetstone and Sieve of Erathostenes.

Computational Chemistry Comparison and Benchmark Database

National Institute of Standards and Technology Data Gateway

SRD 101 NIST Computational Chemistry Comparison and Benchmark Database (Web, free access)   The NIST Computational Chemistry Comparison and Benchmark Database is a collection of experimental and ab initio thermochemical properties for a selected set of molecules. The goals are to provide a benchmark set of molecules for the evaluation of ab initio computational methods and allow the comparison between different ab initio computational methods for the prediction of thermochemical properties.

Internal Benchmarking for Institutional Effectiveness

ERIC Educational Resources Information Center

Ronco, Sharron L.

2012-01-01

Internal benchmarking is an established practice in business and industry for identifying best in-house practices and disseminating the knowledge about those practices to other groups in the organization. Internal benchmarking can be done with structures, processes, outcomes, or even individuals. In colleges or universities with multicampuses or a…

Developing integrated benchmarks for DOE performance measurement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barancik, J.I.; Kramer, C.F.; Thode, Jr. H.C.

1992-09-30

The objectives of this task were to describe and evaluate selected existing sources of information on occupational safety and health with emphasis on hazard and exposure assessment, abatement, training, reporting, and control identifying for exposure and outcome in preparation for developing DOE performance benchmarks. Existing resources and methodologies were assessed for their potential use as practical performance benchmarks. Strengths and limitations of current data resources were identified. Guidelines were outlined for developing new or improved performance factors, which then could become the basis for selecting performance benchmarks. Data bases for non-DOE comparison populations were identified so that DOE performance couldmore » be assessed relative to non-DOE occupational and industrial groups. Systems approaches were described which can be used to link hazards and exposure, event occurrence, and adverse outcome factors, as needed to generate valid, reliable, and predictive performance benchmarks. Data bases were identified which contain information relevant to one or more performance assessment categories . A list of 72 potential performance benchmarks was prepared to illustrate the kinds of information that can be produced through a benchmark development program. Current information resources which may be used to develop potential performance benchmarks are limited. There is need to develop an occupational safety and health information and data system in DOE, which is capable of incorporating demonstrated and documented performance benchmarks prior to, or concurrent with the development of hardware and software. A key to the success of this systems approach is rigorous development and demonstration of performance benchmark equivalents to users of such data before system hardware and software commitments are institutionalized.« less

Accurate Gaussian basis sets for atomic and molecular calculations obtained from the generator coordinate method with polynomial discretization.

PubMed

Celeste, Ricardo; Maringolo, Milena P; Comar, Moacyr; Viana, Rommel B; Guimarães, Amanda R; Haiduke, Roberto L A; da Silva, Albérico B F

2015-10-01

Accurate Gaussian basis sets for atoms from H to Ba were obtained by means of the generator coordinate Hartree-Fock (GCHF) method based on a polynomial expansion to discretize the Griffin-Wheeler-Hartree-Fock equations (GWHF). The discretization of the GWHF equations in this procedure is based on a mesh of points not equally distributed in contrast with the original GCHF method. The results of atomic Hartree-Fock energies demonstrate the capability of these polynomial expansions in designing compact and accurate basis sets to be used in molecular calculations and the maximum error found when compared to numerical values is only 0.788 mHartree for indium. Some test calculations with the B3LYP exchange-correlation functional for N2, F2, CO, NO, HF, and HCN show that total energies within 1.0 to 2.4 mHartree compared to the cc-pV5Z basis sets are attained with our contracted bases with a much smaller number of polarization functions (2p1d and 2d1f for hydrogen and heavier atoms, respectively). Other molecular calculations performed here are also in very good accordance with experimental and cc-pV5Z results. The most important point to be mentioned here is that our generator coordinate basis sets required only a tiny fraction of the computational time when compared to B3LYP/cc-pV5Z calculations.

Benchmark for Strategic Performance Improvement.

ERIC Educational Resources Information Center

Gohlke, Annette

1997-01-01

Explains benchmarking, a total quality management tool used to measure and compare the work processes in a library with those in other libraries to increase library performance. Topics include the main groups of upper management, clients, and staff; critical success factors for each group; and benefits of benchmarking. (Author/LRW)

Beyond Benchmarking: Value-Adding Metrics

ERIC Educational Resources Information Center

Fitz-enz, Jac

2007-01-01

HR metrics has grown up a bit over the past two decades, moving away from simple benchmarking practices and toward a more inclusive approach to measuring institutional performance and progress. In this article, the acknowledged "father" of human capital performance benchmarking provides an overview of several aspects of today's HR metrics…

The NAS kernel benchmark program

NASA Technical Reports Server (NTRS)

Bailey, D. H.; Barton, J. T.

1985-01-01

A collection of benchmark test kernels that measure supercomputer performance has been developed for the use of the NAS (Numerical Aerodynamic Simulation) program at the NASA Ames Research Center. This benchmark program is described in detail and the specific ground rules are given for running the program as a performance test.

How Benchmarking and Higher Education Came Together

ERIC Educational Resources Information Center

Levy, Gary D.; Ronco, Sharron L.

2012-01-01

This chapter introduces the concept of benchmarking and how higher education institutions began to use benchmarking for a variety of purposes. Here, benchmarking is defined as a strategic and structured approach whereby an organization compares aspects of its processes and/or outcomes to those of another organization or set of organizations to…

Benchmarks--Standards Comparisons. Math Competencies: EFF Benchmarks Comparison [and] Reading Competencies: EFF Benchmarks Comparison [and] Writing Competencies: EFF Benchmarks Comparison.

ERIC Educational Resources Information Center

Kent State Univ., OH. Ohio Literacy Resource Center.

This document is intended to show the relationship between Ohio's Standards and Competencies, Equipped for the Future's (EFF's) Standards and Components of Performance, and Ohio's Revised Benchmarks. The document is divided into three parts, with Part 1 covering mathematics instruction, Part 2 covering reading instruction, and Part 3 covering…

Benchmarking infrastructure for mutation text mining

PubMed Central

2014-01-01

Background Experimental research on the automatic extraction of information about mutations from texts is greatly hindered by the lack of consensus evaluation infrastructure for the testing and benchmarking of mutation text mining systems. Results We propose a community-oriented annotation and benchmarking infrastructure to support development, testing, benchmarking, and comparison of mutation text mining systems. The design is based on semantic standards, where RDF is used to represent annotations, an OWL ontology provides an extensible schema for the data and SPARQL is used to compute various performance metrics, so that in many cases no programming is needed to analyze results from a text mining system. While large benchmark corpora for biological entity and relation extraction are focused mostly on genes, proteins, diseases, and species, our benchmarking infrastructure fills the gap for mutation information. The core infrastructure comprises (1) an ontology for modelling annotations, (2) SPARQL queries for computing performance metrics, and (3) a sizeable collection of manually curated documents, that can support mutation grounding and mutation impact extraction experiments. Conclusion We have developed the principal infrastructure for the benchmarking of mutation text mining tasks. The use of RDF and OWL as the representation for corpora ensures extensibility. The infrastructure is suitable for out-of-the-box use in several important scenarios and is ready, in its current state, for initial community adoption. PMID:24568600

Benchmarking infrastructure for mutation text mining.

PubMed

Klein, Artjom; Riazanov, Alexandre; Hindle, Matthew M; Baker, Christopher Jo

2014-02-25

Experimental research on the automatic extraction of information about mutations from texts is greatly hindered by the lack of consensus evaluation infrastructure for the testing and benchmarking of mutation text mining systems. We propose a community-oriented annotation and benchmarking infrastructure to support development, testing, benchmarking, and comparison of mutation text mining systems. The design is based on semantic standards, where RDF is used to represent annotations, an OWL ontology provides an extensible schema for the data and SPARQL is used to compute various performance metrics, so that in many cases no programming is needed to analyze results from a text mining system. While large benchmark corpora for biological entity and relation extraction are focused mostly on genes, proteins, diseases, and species, our benchmarking infrastructure fills the gap for mutation information. The core infrastructure comprises (1) an ontology for modelling annotations, (2) SPARQL queries for computing performance metrics, and (3) a sizeable collection of manually curated documents, that can support mutation grounding and mutation impact extraction experiments. We have developed the principal infrastructure for the benchmarking of mutation text mining tasks. The use of RDF and OWL as the representation for corpora ensures extensibility. The infrastructure is suitable for out-of-the-box use in several important scenarios and is ready, in its current state, for initial community adoption.

Benchmarking: A Process for Improvement.

ERIC Educational Resources Information Center

Peischl, Thomas M.

One problem with the outcome-based measures used in higher education is that they measure quantity but not quality. Benchmarking, or the use of some external standard of quality to measure tasks, processes, and outputs, is partially solving that difficulty. Benchmarking allows for the establishment of a systematic process to indicate if outputs…

Benchmarking in national health service procurement in Scotland.

PubMed

Walker, Scott; Masson, Ron; Telford, Ronnie; White, David

2007-11-01

The paper reports the results of a study on benchmarking activities undertaken by the procurement organization within the National Health Service (NHS) in Scotland, namely National Procurement (previously Scottish Healthcare Supplies Contracts Branch). NHS performance is of course politically important, and benchmarking is increasingly seen as a means to improve performance, so the study was carried out to determine if the current benchmarking approaches could be enhanced. A review of the benchmarking activities used by the private sector, local government and NHS organizations was carried out to establish a framework of the motivations, benefits, problems and costs associated with benchmarking. This framework was used to carry out the research through case studies and a questionnaire survey of NHS procurement organizations both in Scotland and other parts of the UK. Nine of the 16 Scottish Health Boards surveyed reported carrying out benchmarking during the last three years. The findings of the research were that there were similarities in approaches between local government and NHS Scotland Health, but differences between NHS Scotland and other UK NHS procurement organizations. Benefits were seen as significant and it was recommended that National Procurement should pursue the formation of a benchmarking group with members drawn from NHS Scotland and external benchmarking bodies to establish measures to be used in benchmarking across the whole of NHS Scotland.

Hospital benchmarking: are U.S. eye hospitals ready?

PubMed

de Korne, Dirk F; van Wijngaarden, Jeroen D H; Sol, Kees J C A; Betz, Robert; Thomas, Richard C; Schein, Oliver D; Klazinga, Niek S

2012-01-01

Benchmarking is increasingly considered a useful management instrument to improve quality in health care, but little is known about its applicability in hospital settings. The aims of this study were to assess the applicability of a benchmarking project in U.S. eye hospitals and compare the results with an international initiative. We evaluated multiple cases by applying an evaluation frame abstracted from the literature to five U.S. eye hospitals that used a set of 10 indicators for efficiency benchmarking. Qualitative analysis entailed 46 semistructured face-to-face interviews with stakeholders, document analyses, and questionnaires. The case studies only partially met the conditions of the evaluation frame. Although learning and quality improvement were stated as overall purposes, the benchmarking initiative was at first focused on efficiency only. No ophthalmic outcomes were included, and clinicians were skeptical about their reporting relevance and disclosure. However, in contrast with earlier findings in international eye hospitals, all U.S. hospitals worked with internal indicators that were integrated in their performance management systems and supported benchmarking. Benchmarking can support performance management in individual hospitals. Having a certain number of comparable institutes provide similar services in a noncompetitive milieu seems to lay fertile ground for benchmarking. International benchmarking is useful only when these conditions are not met nationally. Although the literature focuses on static conditions for effective benchmarking, our case studies show that it is a highly iterative and learning process. The journey of benchmarking seems to be more important than the destination. Improving patient value (health outcomes per unit of cost) requires, however, an integrative perspective where clinicians and administrators closely cooperate on both quality and efficiency issues. If these worlds do not share such a relationship, the added

INL Results for Phases I and III of the OECD/NEA MHTGR-350 Benchmark

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gerhard Strydom; Javier Ortensi; Sonat Sen

2013-09-01

The Idaho National Laboratory (INL) Very High Temperature Reactor (VHTR) Technology Development Office (TDO) Methods Core Simulation group led the construction of the Organization for Economic Cooperation and Development (OECD) Modular High Temperature Reactor (MHTGR) 350 MW benchmark for comparing and evaluating prismatic VHTR analysis codes. The benchmark is sponsored by the OECD's Nuclear Energy Agency (NEA), and the project will yield a set of reference steady-state, transient, and lattice depletion problems that can be used by the Department of Energy (DOE), the Nuclear Regulatory Commission (NRC), and vendors to assess their code suits. The Methods group is responsible formore » defining the benchmark specifications, leading the data collection and comparison activities, and chairing the annual technical workshops. This report summarizes the latest INL results for Phase I (steady state) and Phase III (lattice depletion) of the benchmark. The INSTANT, Pronghorn and RattleSnake codes were used for the standalone core neutronics modeling of Exercise 1, and the results obtained from these codes are compared in Section 4. Exercise 2 of Phase I requires the standalone steady-state thermal fluids modeling of the MHTGR-350 design, and the results for the systems code RELAP5-3D are discussed in Section 5. The coupled neutronics and thermal fluids steady-state solution for Exercise 3 are reported in Section 6, utilizing the newly developed Parallel and Highly Innovative Simulation for INL Code System (PHISICS)/RELAP5-3D code suit. Finally, the lattice depletion models and results obtained for Phase III are compared in Section 7. The MHTGR-350 benchmark proved to be a challenging simulation set of problems to model accurately, and even with the simplifications introduced in the benchmark specification this activity is an important step in the code-to-code verification of modern prismatic VHTR codes. A final OECD/NEA comparison report will compare the Phase I and III

Benchmark Factors in Student Retention.

ERIC Educational Resources Information Center

Waggener, Anna T.; Smith, Constance K.

The first purpose of this study was to identify significant factors affecting the first benchmark in retaining students in college--the decision to enroll in the first fall semester after orientation. The second purpose was to examine enrollment decisions at the second benchmark--the decision to re-enroll in the second fall semester after freshman…

Aeroelasticity Benchmark Assessment: Subsonic Fixed Wing Program

NASA Technical Reports Server (NTRS)

Florance, Jennifer P.; Chwalowski, Pawel; Wieseman, Carol D.

2010-01-01

The fundamental technical challenge in computational aeroelasticity is the accurate prediction of unsteady aerodynamic phenomena and the effect on the aeroelastic response of a vehicle. Currently, a benchmarking standard for use in validating the accuracy of computational aeroelasticity codes does not exist. Many aeroelastic data sets have been obtained in wind-tunnel and flight testing throughout the world; however, none have been globally presented or accepted as an ideal data set. There are numerous reasons for this. One reason is that often, such aeroelastic data sets focus on the aeroelastic phenomena alone (flutter, for example) and do not contain associated information such as unsteady pressures and time-correlated structural dynamic deflections. Other available data sets focus solely on the unsteady pressures and do not address the aeroelastic phenomena. Other discrepancies can include omission of relevant data, such as flutter frequency and / or the acquisition of only qualitative deflection data. In addition to these content deficiencies, all of the available data sets present both experimental and computational technical challenges. Experimental issues include facility influences, nonlinearities beyond those being modeled, and data processing. From the computational perspective, technical challenges include modeling geometric complexities, coupling between the flow and the structure, grid issues, and boundary conditions. The Aeroelasticity Benchmark Assessment task seeks to examine the existing potential experimental data sets and ultimately choose the one that is viewed as the most suitable for computational benchmarking. An initial computational evaluation of that configuration will then be performed using the Langley-developed computational fluid dynamics (CFD) software FUN3D1 as part of its code validation process. In addition to the benchmarking activity, this task also includes an examination of future research directions. Researchers within the

SP2Bench: A SPARQL Performance Benchmark

NASA Astrophysics Data System (ADS)

Schmidt, Michael; Hornung, Thomas; Meier, Michael; Pinkel, Christoph; Lausen, Georg

A meaningful analysis and comparison of both existing storage schemes for RDF data and evaluation approaches for SPARQL queries necessitates a comprehensive and universal benchmark platform. We present SP2Bench, a publicly available, language-specific performance benchmark for the SPARQL query language. SP2Bench is settled in the DBLP scenario and comprises a data generator for creating arbitrarily large DBLP-like documents and a set of carefully designed benchmark queries. The generated documents mirror vital key characteristics and social-world distributions encountered in the original DBLP data set, while the queries implement meaningful requests on top of this data, covering a variety of SPARQL operator constellations and RDF access patterns. In this chapter, we discuss requirements and desiderata for SPARQL benchmarks and present the SP2Bench framework, including its data generator, benchmark queries and performance metrics.

A New Method for Obtaining Russell-Saunders Terms

ERIC Educational Resources Information Center

Liu, Ying; Liu, Yue; Liu, Bihui

2011-01-01

A new method for obtaining Russell-Saunders terms of atomic configurations is reported. This new method is significantly different from, while at the same time complementary to, previously published methods for obtaining atomic terms. This novel procedure is elicited by the method used to determine the splitting of S, P, D terms in weak ligand…

Benchmark problems and solutions

NASA Technical Reports Server (NTRS)

Tam, Christopher K. W.

1995-01-01

The scientific committee, after careful consideration, adopted six categories of benchmark problems for the workshop. These problems do not cover all the important computational issues relevant to Computational Aeroacoustics (CAA). The deciding factor to limit the number of categories to six was the amount of effort needed to solve these problems. For reference purpose, the benchmark problems are provided here. They are followed by the exact or approximate analytical solutions. At present, an exact solution for the Category 6 problem is not available.

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 4 2013-10-01 2013-10-01 false Benchmark-equivalent health benefits coverage. 440... and Benchmark-Equivalent Coverage § 440.335 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has an aggregate...

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 4 2011-10-01 2011-10-01 false Benchmark-equivalent health benefits coverage. 440... and Benchmark-Equivalent Coverage § 440.335 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has an aggregate...

Benchmarking specialty hospitals, a scoping review on theory and practice.

PubMed

Wind, A; van Harten, W H

2017-04-04

Although benchmarking may improve hospital processes, research on this subject is limited. The aim of this study was to provide an overview of publications on benchmarking in specialty hospitals and a description of study characteristics. We searched PubMed and EMBASE for articles published in English in the last 10 years. Eligible articles described a project stating benchmarking as its objective and involving a specialty hospital or specific patient category; or those dealing with the methodology or evaluation of benchmarking. Of 1,817 articles identified in total, 24 were included in the study. Articles were categorized into: pathway benchmarking, institutional benchmarking, articles on benchmark methodology or -evaluation and benchmarking using a patient registry. There was a large degree of variability:(1) study designs were mostly descriptive and retrospective; (2) not all studies generated and showed data in sufficient detail; and (3) there was variety in whether a benchmarking model was just described or if quality improvement as a consequence of the benchmark was reported upon. Most of the studies that described a benchmark model described the use of benchmarking partners from the same industry category, sometimes from all over the world. Benchmarking seems to be more developed in eye hospitals, emergency departments and oncology specialty hospitals. Some studies showed promising improvement effects. However, the majority of the articles lacked a structured design, and did not report on benchmark outcomes. In order to evaluate the effectiveness of benchmarking to improve quality in specialty hospitals, robust and structured designs are needed including a follow up to check whether the benchmark study has led to improvements.

A benchmark for subduction zone modeling

NASA Astrophysics Data System (ADS)

van Keken, P.; King, S.; Peacock, S.

2003-04-01

Our understanding of subduction zones hinges critically on the ability to discern its thermal structure and dynamics. Computational modeling has become an essential complementary approach to observational and experimental studies. The accurate modeling of subduction zones is challenging due to the unique geometry, complicated rheological description and influence of fluid and melt formation. The complicated physics causes problems for the accurate numerical solution of the governing equations. As a consequence it is essential for the subduction zone community to be able to evaluate the ability and limitations of various modeling approaches. The participants of a workshop on the modeling of subduction zones, held at the University of Michigan at Ann Arbor, MI, USA in 2002, formulated a number of case studies to be developed into a benchmark similar to previous mantle convection benchmarks (Blankenbach et al., 1989; Busse et al., 1991; Van Keken et al., 1997). Our initial benchmark focuses on the dynamics of the mantle wedge and investigates three different rheologies: constant viscosity, diffusion creep, and dislocation creep. In addition we investigate the ability of codes to accurate model dynamic pressure and advection dominated flows. Proceedings of the workshop and the formulation of the benchmark are available at www.geo.lsa.umich.edu/~keken/subduction02.html We strongly encourage interested research groups to participate in this benchmark. At Nice 2003 we will provide an update and first set of benchmark results. Interested researchers are encouraged to contact one of the authors for further details.

XWeB: The XML Warehouse Benchmark

NASA Astrophysics Data System (ADS)

Mahboubi, Hadj; Darmont, Jérôme

With the emergence of XML as a standard for representing business data, new decision support applications are being developed. These XML data warehouses aim at supporting On-Line Analytical Processing (OLAP) operations that manipulate irregular XML data. To ensure feasibility of these new tools, important performance issues must be addressed. Performance is customarily assessed with the help of benchmarks. However, decision support benchmarks do not currently support XML features. In this paper, we introduce the XML Warehouse Benchmark (XWeB), which aims at filling this gap. XWeB derives from the relational decision support benchmark TPC-H. It is mainly composed of a test data warehouse that is based on a unified reference model for XML warehouses and that features XML-specific structures, and its associate XQuery decision support workload. XWeB's usage is illustrated by experiments on several XML database management systems.

Embedded atom method potential for studying mechanical properties of binary Cu–Au alloys

NASA Astrophysics Data System (ADS)

Gola, Adrien; Pastewka, Lars

2018-07-01

We present an embedded atom method (EAM) potential for the binary Cu–Au system. The unary phases are described by two well-tested unary EAM potentials for Cu and Au. We fitted the interaction between Cu and Au to experimental properties of the binary intermetallic phases Cu3Au, CuAu and CuAu3. Particular attention has been paid to reproducing stacking fault energies in order to obtain a potential suitable for studying deformation in this binary system. The resulting energies, lattice constant, elastic properties and melting points are in good agreement with available experimental data. We use nested sampling to show that our potential reproduces the phase boundaries between intermetallic phases and the disordered face-centered cubic solid solution. We benchmark our potential against four popular Cu–Au EAM parameterizations and density-functional theory calculations.

SIGACE Code for Generating High-Temperature ACE Files; Validation and Benchmarking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Amit R.; Ganesan, S.; Trkov, A.

2005-05-24

A code named SIGACE has been developed as a tool for MCNP users within the scope of a research contract awarded by the Nuclear Data Section of the International Atomic Energy Agency (IAEA) (Ref: 302-F4-IND-11566 B5-IND-29641). A new recipe has been evolved for generating high-temperature ACE files for use with the MCNP code. Under this scheme the low-temperature ACE file is first converted to an ENDF formatted file using the ACELST code and then Doppler broadened, essentially limited to the data in the resolved resonance region, to any desired higher temperature using SIGMA1. The SIGACE code then generates a high-temperaturemore » ACE file for use with the MCNP code. A thinning routine has also been introduced in the SIGACE code for reducing the size of the ACE files. The SIGACE code and the recipe for generating ACE files at higher temperatures has been applied to the SEFOR fast reactor benchmark problem (sodium-cooled fast reactor benchmark described in ENDF-202/BNL-19302, 1974 document). The calculated Doppler coefficient is in good agreement with the experimental value. A similar calculation using ACE files generated directly with the NJOY system also agrees with our SIGACE computed results. The SIGACE code and the recipe is further applied to study the numerical benchmark configuration of selected idealized PWR pin cell configurations with five different fuel enrichments as reported by Mosteller and Eisenhart. The SIGACE code that has been tested with several FENDL/MC files will be available, free of cost, upon request, from the Nuclear Data Section of the IAEA.« less

Benchmarking: your performance measurement and improvement tool.

PubMed

Senn, G F

2000-01-01

Many respected professional healthcare organizations and societies today are seeking to establish data-driven performance measurement strategies such as benchmarking. Clinicians are, however, resistant to "benchmarking" that is based on financial data alone, concerned that it may be adverse to the patients' best interests. Benchmarking of clinical procedures that uses physician's codes such as Current Procedural Terminology (CPTs) has greater credibility with practitioners. Better Performers, organizations that can perform procedures successfully at lower cost and in less time, become the "benchmark" against which other organizations can measure themselves. The Better Performers' strategies can be adopted by other facilities to save time or money while maintaining quality patient care.

Benchmark Airport Charges

NASA Technical Reports Server (NTRS)

deWit, A.; Cohn, N.

1999-01-01

The Netherlands Directorate General of Civil Aviation (DGCA) commissioned Hague Consulting Group (HCG) to complete a benchmark study of airport charges at twenty eight airports in Europe and around the world, based on 1996 charges. This study followed previous DGCA research on the topic but included more airports in much more detail. The main purpose of this new benchmark study was to provide insight into the levels and types of airport charges worldwide and into recent changes in airport charge policy and structure, This paper describes the 1996 analysis. It is intended that this work be repeated every year in order to follow developing trends and provide the most up-to-date information possible.

Benchmark Airport Charges

NASA Technical Reports Server (NTRS)

de Wit, A.; Cohn, N.

1999-01-01

The Netherlands Directorate General of Civil Aviation (DGCA) commissioned Hague Consulting Group (HCG) to complete a benchmark study of airport charges at twenty eight airports in Europe and around the world, based on 1996 charges. This study followed previous DGCA research on the topic but included more airports in much more detail. The main purpose of this new benchmark study was to provide insight into the levels and types of airport charges worldwide and into recent changes in airport charge policy and structure. This paper describes the 1996 analysis. It is intended that this work be repeated every year in order to follow developing trends and provide the most up-to-date information possible.

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...) Federal Employees Health Benefit Plan Equivalent Coverage (FEHBP—Equivalent Health Insurance Coverage). A benefit plan equivalent to the standard Blue Cross/Blue Shield preferred provider option service benefit...

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...) Federal Employees Health Benefit Plan Equivalent Coverage (FEHBP—Equivalent Health Insurance Coverage). A benefit plan equivalent to the standard Blue Cross/Blue Shield preferred provider option service benefit...

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...) Federal Employees Health Benefit Plan Equivalent Coverage (FEHBP—Equivalent Health Insurance Coverage). A benefit plan equivalent to the standard Blue Cross/Blue Shield preferred provider option service benefit...

42 CFR 440.330 - Benchmark health benefits coverage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Benchmark-Equivalent Coverage § 440.330 Benchmark health benefits coverage. Benchmark coverage is health...) Federal Employees Health Benefit Plan Equivalent Coverage (FEHBP—Equivalent Health Insurance Coverage). A benefit plan equivalent to the standard Blue Cross/Blue Shield preferred provider option service benefit...

The determination of the excitation tempertaure of the FEI atoms according to the data of the meteor spectra obtained on August 2, 2011

NASA Astrophysics Data System (ADS)

Mozgova, A.; Kleshchonok, V.; Golubaev, A.; Borovička, J.

2017-12-01

This paper presents the results of the determination of the excitation temperature of the FeI atoms according to the data of the meteor spectra obtained on August 2, 2011 in Ondrejov, at the observation station of the Astronomical Institute Observatory of the Academy of Sciences of the Czech Republic.

40 CFR 141.172 - Disinfection profiling and benchmarking.

Code of Federal Regulations, 2011 CFR

2011-07-01

... benchmarking. 141.172 Section 141.172 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Disinfection-Systems Serving 10,000 or More People § 141.172 Disinfection profiling and benchmarking. (a... sanitary surveys conducted by the State. (c) Disinfection benchmarking. (1) Any system required to develop...

Raising Quality and Achievement. A College Guide to Benchmarking.

ERIC Educational Resources Information Center

Owen, Jane

This booklet introduces the principles and practices of benchmarking as a way of raising quality and achievement at further education colleges in Britain. Section 1 defines the concept of benchmarking. Section 2 explains what benchmarking is not and the steps that should be taken before benchmarking is initiated. The following aspects and…

Benchmarking forensic mental health organizations.

PubMed

Coombs, Tim; Taylor, Monica; Pirkis, Jane

2011-04-01

This paper describes the forensic mental health forums that were conducted as part of the National Mental Health Benchmarking Project (NMHBP). These forums encouraged participating organizations to compare their performance on a range of key performance indicators (KPIs) with that of their peers. Four forensic mental health organizations took part in the NMHBP. Representatives from these organizations attended eight benchmarking forums at which they documented their performance against previously agreed KPIs. They also undertook three special projects which explored some of the factors that might explain inter-organizational variation in performance. The inter-organizational range for many of the indicators was substantial. Observing this led participants to conduct the special projects to explore three factors which might help explain the variability - seclusion practices, delivery of community mental health services, and provision of court liaison services. The process of conducting the special projects gave participants insights into the practices and structures employed by their counterparts, and provided them with some important lessons for quality improvement. The forensic mental health benchmarking forums have demonstrated that benchmarking is feasible and likely to be useful in improving service performance and quality.

Adiabatic Quantum Computation with Neutral Atoms

NASA Astrophysics Data System (ADS)

Biedermann, Grant

2013-03-01

We are implementing a new platform for adiabatic quantum computation (AQC)[2] based on trapped neutral atoms whose coupling is mediated by the dipole-dipole interactions of Rydberg states. Ground state cesium atoms are dressed by laser fields in a manner conditional on the Rydberg blockade mechanism,[3,4] thereby providing the requisite entangling interactions. As a benchmark we study a Quadratic Unconstrained Binary Optimization (QUBO) problem whose solution is found in the ground state spin configuration of an Ising-like model. In collaboration with Lambert Parazzoli, Sandia National Laboratories; Aaron Hankin, Center for Quantum Information and Control (CQuIC), University of New Mexico; James Chin-Wen Chou, Yuan-Yu Jau, Peter Schwindt, Cort Johnson, and George Burns, Sandia National Laboratories; Tyler Keating, Krittika Goyal, and Ivan Deutsch, Center for Quantum Information and Control (CQuIC), University of New Mexico; and Andrew Landahl, Sandia National Laboratories. This work was supported by the Laboratory Directed Research and Development program at Sandia National Laboratories

How to Advance TPC Benchmarks with Dependability Aspects

NASA Astrophysics Data System (ADS)

Almeida, Raquel; Poess, Meikel; Nambiar, Raghunath; Patil, Indira; Vieira, Marco

Transactional systems are the core of the information systems of most organizations. Although there is general acknowledgement that failures in these systems often entail significant impact both on the proceeds and reputation of companies, the benchmarks developed and managed by the Transaction Processing Performance Council (TPC) still maintain their focus on reporting bare performance. Each TPC benchmark has to pass a list of dependability-related tests (to verify ACID properties), but not all benchmarks require measuring their performances. While TPC-E measures the recovery time of some system failures, TPC-H and TPC-C only require functional correctness of such recovery. Consequently, systems used in TPC benchmarks are tuned mostly for performance. In this paper we argue that nowadays systems should be tuned for a more comprehensive suite of dependability tests, and that a dependability metric should be part of TPC benchmark publications. The paper discusses WHY and HOW this can be achieved. Two approaches are introduced and discussed: augmenting each TPC benchmark in a customized way, by extending each specification individually; and pursuing a more unified approach, defining a generic specification that could be adjoined to any TPC benchmark.

A Methodology for Benchmarking Relational Database Machines,

DTIC Science & Technology

1984-01-01

user benchmarks is to compare the multiple users to the best-case performance The data for each query classification coll and the performance...called a benchmark. The term benchmark originates from the markers used by sur - veyors in establishing common reference points for their measure...formatted databases. In order to further simplify the problem, we restrict our study to those DBMs which support the relational model. A sur - vey

Protein Models Docking Benchmark 2

PubMed Central

Anishchenko, Ivan; Kundrotas, Petras J.; Tuzikov, Alexander V.; Vakser, Ilya A.

2015-01-01

Structural characterization of protein-protein interactions is essential for our ability to understand life processes. However, only a fraction of known proteins have experimentally determined structures. Such structures provide templates for modeling of a large part of the proteome, where individual proteins can be docked by template-free or template-based techniques. Still, the sensitivity of the docking methods to the inherent inaccuracies of protein models, as opposed to the experimentally determined high-resolution structures, remains largely untested, primarily due to the absence of appropriate benchmark set(s). Structures in such a set should have pre-defined inaccuracy levels and, at the same time, resemble actual protein models in terms of structural motifs/packing. The set should also be large enough to ensure statistical reliability of the benchmarking results. We present a major update of the previously developed benchmark set of protein models. For each interactor, six models were generated with the model-to-native Cα RMSD in the 1 to 6 Å range. The models in the set were generated by a new approach, which corresponds to the actual modeling of new protein structures in the “real case scenario,” as opposed to the previous set, where a significant number of structures were model-like only. In addition, the larger number of complexes (165 vs. 63 in the previous set) increases the statistical reliability of the benchmarking. We estimated the highest accuracy of the predicted complexes (according to CAPRI criteria), which can be attained using the benchmark structures. The set is available at http://dockground.bioinformatics.ku.edu. PMID:25712716

[Do you mean benchmarking?].

PubMed

Bonnet, F; Solignac, S; Marty, J

2008-03-01

The purpose of benchmarking is to settle improvement processes by comparing the activities to quality standards. The proposed methodology is illustrated by benchmark business cases performed inside medical plants on some items like nosocomial diseases or organization of surgery facilities. Moreover, the authors have built a specific graphic tool, enhanced with balance score numbers and mappings, so that the comparison between different anesthesia-reanimation services, which are willing to start an improvement program, is easy and relevant. This ready-made application is even more accurate as far as detailed tariffs of activities are implemented.

Benchmarking, Total Quality Management, and Libraries.

ERIC Educational Resources Information Center

Shaughnessy, Thomas W.

1993-01-01

Discussion of the use of Total Quality Management (TQM) in higher education and academic libraries focuses on the identification, collection, and use of reliable data. Methods for measuring quality, including benchmarking, are described; performance measures are considered; and benchmarking techniques are examined. (11 references) (MES)

Radiation Detection Computational Benchmark Scenarios

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaver, Mark W.; Casella, Andrew M.; Wittman, Richard S.

2013-09-24

Modeling forms an important component of radiation detection development, allowing for testing of new detector designs, evaluation of existing equipment against a wide variety of potential threat sources, and assessing operation performance of radiation detection systems. This can, however, result in large and complex scenarios which are time consuming to model. A variety of approaches to radiation transport modeling exist with complementary strengths and weaknesses for different problems. This variety of approaches, and the development of promising new tools (such as ORNL’s ADVANTG) which combine benefits of multiple approaches, illustrates the need for a means of evaluating or comparing differentmore » techniques for radiation detection problems. This report presents a set of 9 benchmark problems for comparing different types of radiation transport calculations, identifying appropriate tools for classes of problems, and testing and guiding the development of new methods. The benchmarks were drawn primarily from existing or previous calculations with a preference for scenarios which include experimental data, or otherwise have results with a high level of confidence, are non-sensitive, and represent problem sets of interest to NA-22. From a technical perspective, the benchmarks were chosen to span a range of difficulty and to include gamma transport, neutron transport, or both and represent different important physical processes and a range of sensitivity to angular or energy fidelity. Following benchmark identification, existing information about geometry, measurements, and previous calculations were assembled. Monte Carlo results (MCNP decks) were reviewed or created and re-run in order to attain accurate computational times and to verify agreement with experimental data, when present. Benchmark information was then conveyed to ORNL in order to guide testing and development of hybrid calculations. The results of those ADVANTG calculations were then sent to

Benchmarking Helps Measure Union Programs, Operations.

ERIC Educational Resources Information Center

Mann, Jerry

2001-01-01

Explores three examples of benchmarking by college student unions. Focuses on how a union can collect information from other unions for use as benchmarking standards for the purposes of selling a concept or justifying program increases, or for comparing a union's financial performance to other unions. (EV)

Benchmark Study of Global Clean Energy Manufacturing | Advanced

Science.gov Websites

Manufacturing Research | NREL Benchmark Study of Global Clean Energy Manufacturing Benchmark Study of Global Clean Energy Manufacturing Through a first-of-its-kind benchmark study, the Clean Energy Technology End Product.' The study examined four clean energy technologies: wind turbine components

Benchmarking: contexts and details matter.

PubMed

Zheng, Siyuan

2017-07-05

Benchmarking is an essential step in the development of computational tools. We take this opportunity to pitch in our opinions on tool benchmarking, in light of two correspondence articles published in Genome Biology.Please see related Li et al. and Newman et al. correspondence articles: www.dx.doi.org/10.1186/s13059-017-1256-5 and www.dx.doi.org/10.1186/s13059-017-1257-4.

Diagnostic Algorithm Benchmarking

NASA Technical Reports Server (NTRS)

Poll, Scott

2011-01-01

A poster for the NASA Aviation Safety Program Annual Technical Meeting. It describes empirical benchmarking on diagnostic algorithms using data from the ADAPT Electrical Power System testbed and a diagnostic software framework.

MoMaS reactive transport benchmark using PFLOTRAN

NASA Astrophysics Data System (ADS)

Park, H.

2017-12-01

MoMaS benchmark was developed to enhance numerical simulation capability for reactive transport modeling in porous media. The benchmark was published in late September of 2009; it is not taken from a real chemical system, but realistic and numerically challenging tests. PFLOTRAN is a state-of-art massively parallel subsurface flow and reactive transport code that is being used in multiple nuclear waste repository projects at Sandia National Laboratories including Waste Isolation Pilot Plant and Used Fuel Disposition. MoMaS benchmark has three independent tests with easy, medium, and hard chemical complexity. This paper demonstrates how PFLOTRAN is applied to this benchmark exercise and shows results of the easy benchmark test case which includes mixing of aqueous components and surface complexation. Surface complexations consist of monodentate and bidentate reactions which introduces difficulty in defining selectivity coefficient if the reaction applies to a bulk reference volume. The selectivity coefficient becomes porosity dependent for bidentate reaction in heterogeneous porous media. The benchmark is solved by PFLOTRAN with minimal modification to address the issue and unit conversions were made properly to suit PFLOTRAN.

Benchmarking hypercube hardware and software

NASA Technical Reports Server (NTRS)

Grunwald, Dirk C.; Reed, Daniel A.

1986-01-01

It was long a truism in computer systems design that balanced systems achieve the best performance. Message passing parallel processors are no different. To quantify the balance of a hypercube design, an experimental methodology was developed and the associated suite of benchmarks was applied to several existing hypercubes. The benchmark suite includes tests of both processor speed in the absence of internode communication and message transmission speed as a function of communication patterns.

Benchmarking for Excellence and the Nursing Process

NASA Technical Reports Server (NTRS)

Sleboda, Claire

1999-01-01

Nursing is a service profession. The services provided are essential to life and welfare. Therefore, setting the benchmark for high quality care is fundamental. Exploring the definition of a benchmark value will help to determine a best practice approach. A benchmark is the descriptive statement of a desired level of performance against which quality can be judged. It must be sufficiently well understood by managers and personnel in order that it may serve as a standard against which to measure value.

Toward Scalable Benchmarks for Mass Storage Systems

NASA Technical Reports Server (NTRS)

Miller, Ethan L.

1996-01-01

This paper presents guidelines for the design of a mass storage system benchmark suite, along with preliminary suggestions for programs to be included. The benchmarks will measure both peak and sustained performance of the system as well as predicting both short- and long-term behavior. These benchmarks should be both portable and scalable so they may be used on storage systems from tens of gigabytes to petabytes or more. By developing a standard set of benchmarks that reflect real user workload, we hope to encourage system designers and users to publish performance figures that can be compared with those of other systems. This will allow users to choose the system that best meets their needs and give designers a tool with which they can measure the performance effects of improvements to their systems.

Benchmarking and validation activities within JEFF project

NASA Astrophysics Data System (ADS)

Cabellos, O.; Alvarez-Velarde, F.; Angelone, M.; Diez, C. J.; Dyrda, J.; Fiorito, L.; Fischer, U.; Fleming, M.; Haeck, W.; Hill, I.; Ichou, R.; Kim, D. H.; Klix, A.; Kodeli, I.; Leconte, P.; Michel-Sendis, F.; Nunnenmann, E.; Pecchia, M.; Peneliau, Y.; Plompen, A.; Rochman, D.; Romojaro, P.; Stankovskiy, A.; Sublet, J. Ch.; Tamagno, P.; Marck, S. van der

2017-09-01

The challenge for any nuclear data evaluation project is to periodically release a revised, fully consistent and complete library, with all needed data and covariances, and ensure that it is robust and reliable for a variety of applications. Within an evaluation effort, benchmarking activities play an important role in validating proposed libraries. The Joint Evaluated Fission and Fusion (JEFF) Project aims to provide such a nuclear data library, and thus, requires a coherent and efficient benchmarking process. The aim of this paper is to present the activities carried out by the new JEFF Benchmarking and Validation Working Group, and to describe the role of the NEA Data Bank in this context. The paper will also review the status of preliminary benchmarking for the next JEFF-3.3 candidate cross-section files.

Engineering Single-Atom Cobalt Catalysts toward Improved Electrocatalysis.

PubMed

Wan, Gang; Yu, Pengfei; Chen, Hangrong; Wen, Jianguo; Sun, Cheng-Jun; Zhou, Hua; Zhang, Nian; Li, Qianru; Zhao, Wanpeng; Xie, Bing; Li, Tao; Shi, Jianlin

2018-04-01

The development of cost-effective catalysts to replace noble metal is attracting increasing interests in many fields of catalysis and energy, and intensive efforts are focused on the integration of transition-metal sites in carbon as noble-metal-free candidates. Recently, the discovery of single-atom dispersed catalyst (SAC) provides a new frontier in heterogeneous catalysis. However, the electrocatalytic application of SAC is still subject to several theoretical and experimental limitations. Further advances depend on a better design of SAC through optimizing its interaction with adsorbates during catalysis. Here, distinctive from previous studies, favorable 3d electronic occupation and enhanced metal-adsorbates interactions in single-atom centers via the construction of nonplanar coordination is achieved, which is confirmed by advanced X-ray spectroscopic and electrochemical studies. The as-designed atomically dispersed cobalt sites within nonplanar coordination show significantly improved catalytic activity and selectivity toward the oxygen reduction reaction, approaching the benchmark Pt-based catalysts. More importantly, the illustration of the active sites in SAC indicates metal-natured catalytic sites and a media-dependent catalytic pathway. Achieving structural and electronic engineering on SAC that promotes its catalytic performances provides a paradigm to bridge the gap between single-atom catalysts design and electrocatalytic applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Benchmarking short sequence mapping tools

PubMed Central

2013-01-01

Background The development of next-generation sequencing instruments has led to the generation of millions of short sequences in a single run. The process of aligning these reads to a reference genome is time consuming and demands the development of fast and accurate alignment tools. However, the current proposed tools make different compromises between the accuracy and the speed of mapping. Moreover, many important aspects are overlooked while comparing the performance of a newly developed tool to the state of the art. Therefore, there is a need for an objective evaluation method that covers all the aspects. In this work, we introduce a benchmarking suite to extensively analyze sequencing tools with respect to various aspects and provide an objective comparison. Results We applied our benchmarking tests on 9 well known mapping tools, namely, Bowtie, Bowtie2, BWA, SOAP2, MAQ, RMAP, GSNAP, Novoalign, and mrsFAST (mrFAST) using synthetic data and real RNA-Seq data. MAQ and RMAP are based on building hash tables for the reads, whereas the remaining tools are based on indexing the reference genome. The benchmarking tests reveal the strengths and weaknesses of each tool. The results show that no single tool outperforms all others in all metrics. However, Bowtie maintained the best throughput for most of the tests while BWA performed better for longer read lengths. The benchmarking tests are not restricted to the mentioned tools and can be further applied to others. Conclusion The mapping process is still a hard problem that is affected by many factors. In this work, we provided a benchmarking suite that reveals and evaluates the different factors affecting the mapping process. Still, there is no tool that outperforms all of the others in all the tests. Therefore, the end user should clearly specify his needs in order to choose the tool that provides the best results. PMID:23758764

Benchmarking on Tsunami Currents with ComMIT

NASA Astrophysics Data System (ADS)

Sharghi vand, N.; Kanoglu, U.

2015-12-01

There were no standards for the validation and verification of tsunami numerical models before 2004 Indian Ocean tsunami. Even, number of numerical models has been used for inundation mapping effort, evaluation of critical structures, etc. without validation and verification. After 2004, NOAA Center for Tsunami Research (NCTR) established standards for the validation and verification of tsunami numerical models (Synolakis et al. 2008 Pure Appl. Geophys. 165, 2197-2228), which will be used evaluation of critical structures such as nuclear power plants against tsunami attack. NCTR presented analytical, experimental and field benchmark problems aimed to estimate maximum runup and accepted widely by the community. Recently, benchmark problems were suggested by the US National Tsunami Hazard Mitigation Program Mapping & Modeling Benchmarking Workshop: Tsunami Currents on February 9-10, 2015 at Portland, Oregon, USA (http://nws.weather.gov/nthmp/index.html). These benchmark problems concentrated toward validation and verification of tsunami numerical models on tsunami currents. Three of the benchmark problems were: current measurement of the Japan 2011 tsunami in Hilo Harbor, Hawaii, USA and in Tauranga Harbor, New Zealand, and single long-period wave propagating onto a small-scale experimental model of the town of Seaside, Oregon, USA. These benchmark problems were implemented in the Community Modeling Interface for Tsunamis (ComMIT) (Titov et al. 2011 Pure Appl. Geophys. 168, 2121-2131), which is a user-friendly interface to the validated and verified Method of Splitting Tsunami (MOST) (Titov and Synolakis 1995 J. Waterw. Port Coastal Ocean Eng. 121, 308-316) model and is developed by NCTR. The modeling results are compared with the required benchmark data, providing good agreements and results are discussed. Acknowledgment: The research leading to these results has received funding from the European Union's Seventh Framework Programme (FP7/2007-2013) under grant

Benchmarking child and adolescent mental health organizations.

PubMed

Brann, Peter; Walter, Garry; Coombs, Tim

2011-04-01

This paper describes aspects of the child and adolescent benchmarking forums that were part of the National Mental Health Benchmarking Project (NMHBP). These forums enabled participating child and adolescent mental health organizations to benchmark themselves against each other, with a view to understanding variability in performance against a range of key performance indicators (KPIs). Six child and adolescent mental health organizations took part in the NMHBP. Representatives from these organizations attended eight benchmarking forums at which they documented their performance against relevant KPIs. They also undertook two special projects designed to help them understand the variation in performance on given KPIs. There was considerable inter-organization variability on many of the KPIs. Even within organizations, there was often substantial variability over time. The variability in indicator data raised many questions for participants. This challenged participants to better understand and describe their local processes, prompted them to collect additional data, and stimulated them to make organizational comparisons. These activities fed into a process of reflection about their performance. Benchmarking has the potential to illuminate intra- and inter-organizational performance in the child and adolescent context.

Benchmarks: The Development of a New Approach to Student Evaluation.

ERIC Educational Resources Information Center

Larter, Sylvia

The Toronto Board of Education Benchmarks are libraries of reference materials that demonstrate student achievement at various levels. Each library contains video benchmarks, print benchmarks, a staff handbook, and summary and introductory documents. This book is about the development and the history of the benchmark program. It has taken over 3…

42 CFR 457.430 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 4 2011-10-01 2011-10-01 false Benchmark-equivalent health benefits coverage. 457... STATES State Plan Requirements: Coverage and Benefits § 457.430 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has...

42 CFR 457.430 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 4 2013-10-01 2013-10-01 false Benchmark-equivalent health benefits coverage. 457... STATES State Plan Requirements: Coverage and Benefits § 457.430 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has...

42 CFR 457.430 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Benchmark-equivalent health benefits coverage. 457... STATES State Plan Requirements: Coverage and Benefits § 457.430 Benchmark-equivalent health benefits coverage. (a) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has...

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 4 2012-10-01 2012-10-01 false Benchmark-equivalent health benefits coverage. 440.335 Section 440.335 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND... and Benchmark-Equivalent Coverage § 440.335 Benchmark-equivalent health benefits coverage. (a...

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 4 2014-10-01 2014-10-01 false Benchmark-equivalent health benefits coverage. 440.335 Section 440.335 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND... and Benchmark-Equivalent Coverage § 440.335 Benchmark-equivalent health benefits coverage. (a...

Portfolio selection and asset pricing under a benchmark approach

NASA Astrophysics Data System (ADS)

Platen, Eckhard

2006-10-01

The paper presents classical and new results on portfolio optimization, as well as the fair pricing concept for derivative pricing under the benchmark approach. The growth optimal portfolio is shown to be a central object in a market model. It links asset pricing and portfolio optimization. The paper argues that the market portfolio is a proxy of the growth optimal portfolio. By choosing the drift of the discounted growth optimal portfolio as parameter process, one obtains a realistic theoretical market dynamics.

Photochemistry in Terrestrial Exoplanet Atmospheres. I. Photochemistry Model and Benchmark Cases

NASA Astrophysics Data System (ADS)

Hu, Renyu; Seager, Sara; Bains, William

2012-12-01

We present a comprehensive photochemistry model for exploration of the chemical composition of terrestrial exoplanet atmospheres. The photochemistry model is designed from the ground up to have the capacity to treat all types of terrestrial planet atmospheres, ranging from oxidizing through reducing, which makes the code suitable for applications for the wide range of anticipated terrestrial exoplanet compositions. The one-dimensional chemical transport model treats up to 800 chemical reactions, photochemical processes, dry and wet deposition, surface emission, and thermal escape of O, H, C, N, and S bearing species, as well as formation and deposition of elemental sulfur and sulfuric acid aerosols. We validate the model by computing the atmospheric composition of current Earth and Mars and find agreement with observations of major trace gases in Earth's and Mars' atmospheres. We simulate several plausible atmospheric scenarios of terrestrial exoplanets and choose three benchmark cases for atmospheres from reducing to oxidizing. The most interesting finding is that atomic hydrogen is always a more abundant reactive radical than the hydroxyl radical in anoxic atmospheres. Whether atomic hydrogen is the most important removal path for a molecule of interest also depends on the relevant reaction rates. We also find that volcanic carbon compounds (i.e., CH4 and CO2) are chemically long-lived and tend to be well mixed in both reducing and oxidizing atmospheres, and their dry deposition velocities to the surface control the atmospheric oxidation states. Furthermore, we revisit whether photochemically produced oxygen can cause false positives for detecting oxygenic photosynthesis, and find that in 1 bar CO2-rich atmospheres oxygen and ozone may build up to levels that have conventionally been accepted as signatures of life, if there is no surface emission of reducing gases. The atmospheric scenarios presented in this paper can serve as the benchmark atmospheres for

Development and Application of Benchmark Examples for Mixed-Mode I/II Quasi-Static Delamination Propagation Predictions

NASA Technical Reports Server (NTRS)

Krueger, Ronald

2012-01-01

The development of benchmark examples for quasi-static delamination propagation prediction is presented and demonstrated for a commercial code. The examples are based on finite element models of the Mixed-Mode Bending (MMB) specimen. The examples are independent of the analysis software used and allow the assessment of the automated delamination propagation prediction capability in commercial finite element codes based on the virtual crack closure technique (VCCT). First, quasi-static benchmark examples were created for the specimen. Second, starting from an initially straight front, the delamination was allowed to propagate under quasi-static loading. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Good agreement between the results obtained from the automated propagation analysis and the benchmark results could be achieved by selecting input parameters that had previously been determined during analyses of mode I Double Cantilever Beam and mode II End Notched Flexure specimens. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Overall the results are encouraging, but further assessment for mixed-mode delamination fatigue onset and growth is required.

Taking the Battle Upstream: Towards a Benchmarking Role for NATO

DTIC Science & Technology

2012-09-01

Benchmark.........................................................................................14 Figure 8. World Bank Benchmarking Work on Quality...Search of a Benchmarking Theory for the Public Sector.” 16     Figure 8. World Bank Benchmarking Work on Quality of Governance One of the most...the Ministries of Defense in the countries in which it works ). Another interesting innovation is that for comparison purposes, McKinsey categorized

Human Health Benchmarks for Pesticides

EPA Pesticide Factsheets

Advanced testing methods now allow pesticides to be detected in water at very low levels. These small amounts of pesticides detected in drinking water or source water for drinking water do not necessarily indicate a health risk. The EPA has developed human health benchmarks for 363 pesticides to enable our partners to better determine whether the detection of a pesticide in drinking water or source waters for drinking water may indicate a potential health risk and to help them prioritize monitoring efforts.The table below includes benchmarks for acute (one-day) and chronic (lifetime) exposures for the most sensitive populations from exposure to pesticides that may be found in surface or ground water sources of drinking water. The table also includes benchmarks for 40 pesticides in drinking water that have the potential for cancer risk. The HHBP table includes pesticide active ingredients for which Health Advisories or enforceable National Primary Drinking Water Regulations (e.g., maximum contaminant levels) have not been developed.

Benchmarking to improve the quality of cystic fibrosis care.

PubMed

Schechter, Michael S

2012-11-01

Benchmarking involves the ascertainment of healthcare programs with most favorable outcomes as a means to identify and spread effective strategies for delivery of care. The recent interest in the development of patient registries for patients with cystic fibrosis (CF) has been fueled in part by an interest in using them to facilitate benchmarking. This review summarizes reports of how benchmarking has been operationalized in attempts to improve CF care. Although certain goals of benchmarking can be accomplished with an exclusive focus on registry data analysis, benchmarking programs in Germany and the United States have supplemented these data analyses with exploratory interactions and discussions to better understand successful approaches to care and encourage their spread throughout the care network. Benchmarking allows the discovery and facilitates the spread of effective approaches to care. It provides a pragmatic alternative to traditional research methods such as randomized controlled trials, providing insights into methods that optimize delivery of care and allowing judgments about the relative effectiveness of different therapeutic approaches.

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2014 CFR

2014-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2012 CFR

2012-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2011 CFR

2011-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2010 CFR

2010-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

29 CFR 1952.153 - Compliance staffing benchmarks.

Code of Federal Regulations, 2013 CFR

2013-07-01

... further revision of its benchmarks to 64 safety inspectors and 50 industrial hygienists. After opportunity... Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION... benchmarks of 50 safety and 27 health compliance officers. After opportunity for public comment and service...

Python/Lua Benchmarks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Busby, L.

This is an adaptation of the pre-existing Scimark benchmark code to a variety of Python and Lua implementations. It also measures performance of the Fparser expression parser and C and C++ code on a variety of simple scientific expressions.

Benchmarking image fusion system design parameters

NASA Astrophysics Data System (ADS)

Howell, Christopher L.

2013-06-01

A clear and absolute method for discriminating between image fusion algorithm performances is presented. This method can effectively be used to assist in the design and modeling of image fusion systems. Specifically, it is postulated that quantifying human task performance using image fusion should be benchmarked to whether the fusion algorithm, at a minimum, retained the performance benefit achievable by each independent spectral band being fused. The established benchmark would then clearly represent the threshold that a fusion system should surpass to be considered beneficial to a particular task. A genetic algorithm is employed to characterize the fused system parameters using a Matlab® implementation of NVThermIP as the objective function. By setting the problem up as a mixed-integer constraint optimization problem, one can effectively look backwards through the image acquisition process: optimizing fused system parameters by minimizing the difference between modeled task difficulty measure and the benchmark task difficulty measure. The results of an identification perception experiment are presented, where human observers were asked to identify a standard set of military targets, and used to demonstrate the effectiveness of the benchmarking process.

Benchmark Evaluation of HTR-PROTEUS Pebble Bed Experimental Program

DOE PAGES

Bess, John D.; Montierth, Leland; Köberl, Oliver; ...

2014-10-09

Benchmark models were developed to evaluate 11 critical core configurations of the HTR-PROTEUS pebble bed experimental program. Various additional reactor physics measurements were performed as part of this program; currently only a total of 37 absorber rod worth measurements have been evaluated as acceptable benchmark experiments for Cores 4, 9, and 10. Dominant uncertainties in the experimental keff for all core configurations come from uncertainties in the ²³⁵U enrichment of the fuel, impurities in the moderator pebbles, and the density and impurity content of the radial reflector. Calculations of k eff with MCNP5 and ENDF/B-VII.0 neutron nuclear data aremore » greater than the benchmark values but within 1% and also within the 3σ uncertainty, except for Core 4, which is the only randomly packed pebble configuration. Repeated calculations of k eff with MCNP6.1 and ENDF/B-VII.1 are lower than the benchmark values and within 1% (~3σ) except for Cores 5 and 9, which calculate lower than the benchmark eigenvalues within 4σ. The primary difference between the two nuclear data libraries is the adjustment of the absorption cross section of graphite. Simulations of the absorber rod worth measurements are within 3σ of the benchmark experiment values. The complete benchmark evaluation details are available in the 2014 edition of the International Handbook of Evaluated Reactor Physics Benchmark Experiments.« less

Benchmark problems for numerical implementations of phase field models

DOE PAGES

Jokisaari, A. M.; Voorhees, P. W.; Guyer, J. E.; ...

2016-10-01

Here, we present the first set of benchmark problems for phase field models that are being developed by the Center for Hierarchical Materials Design (CHiMaD) and the National Institute of Standards and Technology (NIST). While many scientific research areas use a limited set of well-established software, the growing phase field community continues to develop a wide variety of codes and lacks benchmark problems to consistently evaluate the numerical performance of new implementations. Phase field modeling has become significantly more popular as computational power has increased and is now becoming mainstream, driving the need for benchmark problems to validate and verifymore » new implementations. We follow the example set by the micromagnetics community to develop an evolving set of benchmark problems that test the usability, computational resources, numerical capabilities and physical scope of phase field simulation codes. In this paper, we propose two benchmark problems that cover the physics of solute diffusion and growth and coarsening of a second phase via a simple spinodal decomposition model and a more complex Ostwald ripening model. We demonstrate the utility of benchmark problems by comparing the results of simulations performed with two different adaptive time stepping techniques, and we discuss the needs of future benchmark problems. The development of benchmark problems will enable the results of quantitative phase field models to be confidently incorporated into integrated computational materials science and engineering (ICME), an important goal of the Materials Genome Initiative.« less

Design considerations regarding an atomizer for multi-element electrothermal atomic absorption spectrometry

NASA Astrophysics Data System (ADS)

Katskov, Dmitri A.; Sadagov, Yuri M.

2011-06-01

The methodology of simultaneous multi-element electrothermal atomic absorption spectrometry (ETAAS-Electrothermal Atomic Absorption Spectrometry) stipulates rigid requirements to the design and operation of the atomizer. It must provide high degree of atomization for the group of analytes, invariant respective to the vaporization kinetics and heating ramp residence time of atoms in the absorption volume and absence of memory effects from major sample components. For the low resolution spectrometer with a continuum radiation source the reduced compared to traditional ETAAS (Electrothermal Atomic Absorption Spectrometry) sensitivity should be, at least partially, compensated by creating high density of atomic vapor in the absorption pulse. The sought-for characteristics were obtained for the 18 mm in length and 2.5 mm in internal diameter longitudinally heated graphite tube atomizer furnished with 2-4.5 mg of ring shaped carbon fiber yarn collector. The collector located next to the sampling port provides large substrate area that helps to keep the sample and its residue in the central part of the tube after drying. The collector also provides a "platform" effect that delays the vaporization and stipulates vapor release into absorption volume having already stabilized gas temperature. Due to the shape of external surface of the tube, presence of collector and rapid (about 10 °C/ms) heating, an inverse temperature distribution along the tube is attained at the beginnings of the atomization and cleaning steps. The effect is employed for cleaning of the atomizer using the set of short maximum power heating pulses. Preparation, optimal maintenance of the atomizer and its compliance to the multi-element determination requirements are evaluated and discussed. The experimental setup provides direct simultaneous determination of large group of element within 3-4 order concentration range. Limits of detection are close to those for sequential single element determination in

Using Benchmarking To Influence Tuition and Fee Decisions.

ERIC Educational Resources Information Center

Hubbell, Loren W. Loomis; Massa, Robert J.; Lapovsky, Lucie

2002-01-01

Discusses the use of benchmarking in managing enrollment. Using a case study, illustrates how benchmarking can help administrators develop strategies for planning and implementing admissions and pricing practices. (EV)

An interface capturing scheme for modeling atomization in compressible flows

NASA Astrophysics Data System (ADS)

Garrick, Daniel P.; Hagen, Wyatt A.; Regele, Jonathan D.

2017-09-01

The study of atomization in supersonic flow is critical to ensuring reliable ignition of scramjet combustors under startup conditions. Numerical methods incorporating surface tension effects have largely focused on the incompressible regime as most atomization applications occur at low Mach numbers. Simulating surface tension effects in compressible flow requires robust numerical methods that can handle discontinuities caused by both shocks and material interfaces with high density ratios. In this work, a shock and interface capturing scheme is developed that uses the Harten-Lax-van Leer-Contact (HLLC) Riemann solver while a Tangent of Hyperbola for INterface Capturing (THINC) interface reconstruction scheme retains the fluid immiscibility condition in the volume fraction and phasic densities in the context of the five equation model. The approach includes the effects of compressibility, surface tension, and molecular viscosity. One and two-dimensional benchmark problems demonstrate the desirable interface sharpening and conservation properties of the approach. Simulations of secondary atomization of a cylindrical water column after its interaction with a shockwave show good qualitative agreement with experimentally observed behavior. Three-dimensional examples of primary atomization of a liquid jet in a Mach 2 crossflow demonstrate the robustness of the method.

Hirshfeld atom refinement.

PubMed

Capelli, Silvia C; Bürgi, Hans-Beat; Dittrich, Birger; Grabowsky, Simon; Jayatilaka, Dylan

2014-09-01

Hirshfeld atom refinement (HAR) is a method which determines structural parameters from single-crystal X-ray diffraction data by using an aspherical atom partitioning of tailor-made ab initio quantum mechanical molecular electron densities without any further approximation. Here the original HAR method is extended by implementing an iterative procedure of successive cycles of electron density calculations, Hirshfeld atom scattering factor calculations and structural least-squares refinements, repeated until convergence. The importance of this iterative procedure is illustrated via the example of crystalline ammonia. The new HAR method is then applied to X-ray diffraction data of the dipeptide Gly-l-Ala measured at 12, 50, 100, 150, 220 and 295 K, using Hartree-Fock and BLYP density functional theory electron densities and three different basis sets. All positions and anisotropic displacement parameters (ADPs) are freely refined without constraints or restraints - even those for hydrogen atoms. The results are systematically compared with those from neutron diffraction experiments at the temperatures 12, 50, 150 and 295 K. Although non-hydrogen-atom ADPs differ by up to three combined standard uncertainties (csu's), all other structural parameters agree within less than 2 csu's. Using our best calculations (BLYP/cc-pVTZ, recommended for organic molecules), the accuracy of determining bond lengths involving hydrogen atoms from HAR is better than 0.009 Å for temperatures of 150 K or below; for hydrogen-atom ADPs it is better than 0.006 Å(2) as judged from the mean absolute X-ray minus neutron differences. These results are among the best ever obtained. Remarkably, the precision of determining bond lengths and ADPs for the hydrogen atoms from the HAR procedure is comparable with that from the neutron measurements - an outcome which is obtained with a routinely achievable resolution of the X-ray data of 0.65 Å.

Atomic resolution holography.

PubMed

Hayashi, Kouichi

2014-11-01

Atomic resolution holography, such as X-ray fluorescence holography (XFH)[1] and photoelectron holography (PH), has the attention of researcher as an informative local structure analysis, because it provides three dimensional atomic images around specific elements within a range of a few nanometers. It can determine atomic arrangements around a specific element without any prior knowledge of structures. It is considered that the atomic resolution holographic is a third method of structural analysis at the atomic level after X-ray diffraction (XRD) and X-ray absorption fine structure (XAFS). As known by many researchers, XRD and XAFS are established methods that are widespread use in various fields. XRD and XAFS provide information on long-range translational periodicities and very local environments, respectively, whereas the atomic resolution holography gives 3D information on the local order and can visualize surrounding atoms with a large range of coordination shells. We call this feature "3D medium-range local structure observation".In addition to this feature, the atomic resolution holography is very sensitive to the displacement of atoms from their ideal positions, and one can obtain quantitative information about local lattice distortions by analyzing reconstructed atomic images[2] When dopants with different atomic radii from the matrix elements are present, the lattices around the dopants are distorted. However, using the conventional methods of structural analysis, one cannot determine the extent to which the local lattice distortions are preserved from the dopants. XFH is a good tool for solving this problem.Figure 1 shows a recent achievement on a relaxor ferroelectric of Pb(Mg1/3Nb2/3)O3 (PMN) using XFH. The structural studies of relaxor ferroelectrics have been carried out by X-ray or neutron diffractions, which suggested rhombohedral distortions of their lattices. However, their true pictures have not been obtained, yet. The Nb Kα holograms showed

Kohn-Sham Band Structure Benchmark Including Spin-Orbit Coupling for 2D and 3D Solids

NASA Astrophysics Data System (ADS)

Huhn, William; Blum, Volker

2015-03-01

Accurate electronic band structures serve as a primary indicator of the suitability of a material for a given application, e.g., as electronic or catalytic materials. Computed band structures, however, are subject to a host of approximations, some of which are more obvious (e.g., the treatment of the exchange-correlation of self-energy) and others less obvious (e.g., the treatment of core, semicore, or valence electrons, handling of relativistic effects, or the accuracy of the underlying basis set used). We here provide a set of accurate Kohn-Sham band structure benchmarks, using the numeric atom-centered all-electron electronic structure code FHI-aims combined with the ``traditional'' PBE functional and the hybrid HSE functional, to calculate core, valence, and low-lying conduction bands of a set of 2D and 3D materials. Benchmarks are provided with and without effects of spin-orbit coupling, using quasi-degenerate perturbation theory to predict spin-orbit splittings. This work is funded by Fritz-Haber-Institut der Max-Planck-Gesellschaft.

Atomic Physics Effects on Convergent, Child-Langmuir Ion Flow between Nearly Transparent Electrodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santarius, John F.; Emmert, Gilbert A.

Research during this project at the University of Wisconsin Fusion Technology Institute (UW FTI) on ion and neutral flow through an arbitrary, monotonic potential difference created by nearly transparent electrodes accomplished the following: (1) developed and implemented an integral equation approach for atomic physics effects in helium plasmas; (2) extended the analysis to coupled integral equations that treat atomic and molecular deuterium ions and neutrals; (3) implemented the key deuterium and helium atomic and molecular cross sections; (4) added negative ion production and related cross sections; and (5) benchmarked the code against experimental results. The analysis and codes treat themore » species D0, D20, D+, D2+, D3+, D and, separately at present, He0 and He+. Extensions enhanced the analysis and related computer codes to include He++ ions plus planar and cylindrical geometries.« less

PMLB: a large benchmark suite for machine learning evaluation and comparison.

PubMed

Olson, Randal S; La Cava, William; Orzechowski, Patryk; Urbanowicz, Ryan J; Moore, Jason H

2017-01-01

The selection, development, or comparison of machine learning methods in data mining can be a difficult task based on the target problem and goals of a particular study. Numerous publicly available real-world and simulated benchmark datasets have emerged from different sources, but their organization and adoption as standards have been inconsistent. As such, selecting and curating specific benchmarks remains an unnecessary burden on machine learning practitioners and data scientists. The present study introduces an accessible, curated, and developing public benchmark resource to facilitate identification of the strengths and weaknesses of different machine learning methodologies. We compare meta-features among the current set of benchmark datasets in this resource to characterize the diversity of available data. Finally, we apply a number of established machine learning methods to the entire benchmark suite and analyze how datasets and algorithms cluster in terms of performance. From this study, we find that existing benchmarks lack the diversity to properly benchmark machine learning algorithms, and there are several gaps in benchmarking problems that still need to be considered. This work represents another important step towards understanding the limitations of popular benchmarking suites and developing a resource that connects existing benchmarking standards to more diverse and efficient standards in the future.

47 CFR 69.108 - Transport rate benchmark.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 3 2010-10-01 2010-10-01 false Transport rate benchmark. 69.108 Section 69.108... Computation of Charges § 69.108 Transport rate benchmark. (a) For transport charges computed in accordance... interoffice transmission using the telephone company's DS1 special access rates. (b) Initial transport rates...

47 CFR 69.108 - Transport rate benchmark.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 3 2011-10-01 2011-10-01 false Transport rate benchmark. 69.108 Section 69.108... Computation of Charges § 69.108 Transport rate benchmark. (a) For transport charges computed in accordance... interoffice transmission using the telephone company's DS1 special access rates. (b) Initial transport rates...

Electric-Drive Vehicle Thermal Performance Benchmarking | Transportation

Science.gov Websites

studies are as follows: Characterize the thermal resistance and conductivity of various layers in the Research | NREL Electric-Drive Vehicle Thermal Performance Benchmarking Electric-Drive Vehicle Thermal Performance Benchmarking A photo of the internal components of an automotive inverter. NREL

Unstructured Adaptive (UA) NAS Parallel Benchmark. Version 1.0

NASA Technical Reports Server (NTRS)

Feng, Huiyu; VanderWijngaart, Rob; Biswas, Rupak; Mavriplis, Catherine

2004-01-01

We present a complete specification of a new benchmark for measuring the performance of modern computer systems when solving scientific problems featuring irregular, dynamic memory accesses. It complements the existing NAS Parallel Benchmark suite. The benchmark involves the solution of a stylized heat transfer problem in a cubic domain, discretized on an adaptively refined, unstructured mesh.

BENCHMARKING SUSTAINABILITY ENGINEERING EDUCATION

EPA Science Inventory

The goals of this project are to develop and apply a methodology for benchmarking curricula in sustainability engineering and to identify individuals active in sustainability engineering education.

Refined tip preparation by electrochemical etching and ultrahigh vacuum treatment to obtain atomically sharp tips for scanning tunneling microscope and atomic force microscope.

PubMed

Hagedorn, Till; El Ouali, Mehdi; Paul, William; Oliver, David; Miyahara, Yoichi; Grütter, Peter

2011-11-01

A modification of the common electrochemical etching setup is presented. The described method reproducibly yields sharp tungsten tips for usage in the scanning tunneling microscope and tuning fork atomic force microscope. In situ treatment under ultrahigh vacuum (p ≤10(-10) mbar) conditions for cleaning and fine sharpening with minimal blunting is described. The structure of the microscopic apex of these tips is atomically resolved with field ion microscopy and cross checked with field emission. © 2011 American Institute of Physics

Performance Evaluation of Supercomputers using HPCC and IMB Benchmarks

NASA Technical Reports Server (NTRS)

Saini, Subhash; Ciotti, Robert; Gunney, Brian T. N.; Spelce, Thomas E.; Koniges, Alice; Dossa, Don; Adamidis, Panagiotis; Rabenseifner, Rolf; Tiyyagura, Sunil R.; Mueller, Matthias;

Coaxial airblast atomizers

NASA Technical Reports Server (NTRS)

Hardalupas, Y.; Whitelaw, J. H.

1993-01-01

An experimental investigation was performed to quantify the characteristics of the sprays of coaxial injectors with particular emphasis on those aspects relevant to the performance of rocket engines. Measurements for coaxial air blast atomizers were obtained using air to represent the gaseous stream and water to represent the liquid stream. A wide range of flow conditions were examined for sprays with and without swirl for gaseous streams. The parameters varied include Weber number, gas flow rate, liquid flow rate, swirl, and nozzle geometry. Measurements were made with a phase Doppler velocimeter. Major conclusions of the study focused upon droplet size as a function of Weber number, effect of gas flow rate on atomization and spray spread, effect of nozzle geometry on atomization and spread, effect of swirl on atomization, spread, jet recirculation and breakup, and secondary atomization.

Study of Li atom diffusion in amorphous Li3PO4 with neural network potential

NASA Astrophysics Data System (ADS)

Li, Wenwen; Ando, Yasunobu; Minamitani, Emi; Watanabe, Satoshi

2017-12-01

To clarify atomic diffusion in amorphous materials, which is important in novel information and energy devices, theoretical methods having both reliability and computational speed are eagerly anticipated. In the present study, we applied neural network (NN) potentials, a recently developed machine learning technique, to the study of atom diffusion in amorphous materials, using Li3PO4 as a benchmark material. The NN potential was used together with the nudged elastic band, kinetic Monte Carlo, and molecular dynamics methods to characterize Li vacancy diffusion behavior in the amorphous Li3PO4 model. By comparing these results with corresponding DFT calculations, we found that the average error of the NN potential is 0.048 eV in calculating energy barriers of diffusion paths, and 0.041 eV in diffusion activation energy. Moreover, the diffusion coefficients obtained from molecular dynamics are always consistent with those from ab initio molecular dynamics simulation, while the computation speed of the NN potential is 3-4 orders of magnitude faster than DFT. Lastly, the structure of amorphous Li3PO4 and the ion transport properties in it were studied with the NN potential using a large supercell model containing more than 1000 atoms. The formation of P2O7 units was observed, which is consistent with the experimental characterization. The Li diffusion activation energy was estimated to be 0.55 eV, which agrees well with the experimental measurements.

Sequoia Messaging Rate Benchmark

DOE Office of Scientific and Technical Information (OSTI.GOV)

Friedley, Andrew

2008-01-22

The purpose of this benchmark is to measure the maximal message rate of a single compute node. The first num_cores ranks are expected to reside on the 'core' compute node for which message rate is being tested. After that, the next num_nbors ranks are neighbors for the first core rank, the next set of num_nbors ranks are neighbors for the second core rank, and so on. For example, testing an 8-core node (num_cores = 8) with 4 neighbors (num_nbors = 4) requires 8 + 8 * 4 - 40 ranks. The first 8 of those 40 ranks are expected tomore » be on the 'core' node being benchmarked, while the rest of the ranks are on separate nodes.« less

Using a health promotion model to promote benchmarking.

PubMed

Welby, Jane

2006-07-01

The North East (England) Neonatal Benchmarking Group has been established for almost a decade and has researched and developed a substantial number of evidence-based benchmarks. With no firm evidence that these were being used or that there was any standardisation of neonatal care throughout the region, the group embarked on a programme to review the benchmarks and determine what evidence-based guidelines were needed to support standardisation. A health promotion planning model was used by one subgroup to structure the programme; it enabled all members of the sub group to engage in the review process and provided the motivation and supporting documentation for implementation of changes in practice. The need for a regional guideline development group to complement the activity of the benchmarking group is being addressed.

Experimental Criticality Benchmarks for SNAP 10A/2 Reactor Cores

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krass, A.W.

2005-12-19

This report describes computational benchmark models for nuclear criticality derived from descriptions of the Systems for Nuclear Auxiliary Power (SNAP) Critical Assembly (SCA)-4B experimental criticality program conducted by Atomics International during the early 1960's. The selected experimental configurations consist of fueled SNAP 10A/2-type reactor cores subject to varied conditions of water immersion and reflection under experimental control to measure neutron multiplication. SNAP 10A/2-type reactor cores are compact volumes fueled and moderated with the hydride of highly enriched uranium-zirconium alloy. Specifications for the materials and geometry needed to describe a given experimental configuration for a model using MCNP5 are provided. Themore » material and geometry specifications are adequate to permit user development of input for alternative nuclear safety codes, such as KENO. A total of 73 distinct experimental configurations are described.« less

Efficient atom localization via probe absorption in an inverted-Y atomic system

NASA Astrophysics Data System (ADS)

Wu, Jianchun; Wu, Bo; Mao, Jiejian

2018-06-01

The behaviour of atom localization in an inverted-Y atomic system is theoretically investigated. For the atoms interacting with a weak probe field and several orthogonal standing-wave fields, their position information can be obtained by measuring the probe absorption. Compared with the traditional scheme, we couple the probe field to the transition between the middle and top levels. It is found that the probe absorption sensitively depends on the detuning and strength of the relevant light fields. Remarkably, the atom can be localized at a particular position in the standing-wave fields by coupling a microwave field to the transition between the two ground levels.

Non-adiabatic quantum state preparation and quantum state transport in chains of Rydberg atoms

NASA Astrophysics Data System (ADS)

Ostmann, Maike; Minář, Jiří; Marcuzzi, Matteo; Levi, Emanuele; Lesanovsky, Igor

2017-12-01

Motivated by recent progress in the experimental manipulation of cold atoms in optical lattices, we study three different protocols for non-adiabatic quantum state preparation and state transport in chains of Rydberg atoms. The protocols we discuss are based on the blockade mechanism between atoms which, when excited to a Rydberg state, interact through a van der Waals potential, and rely on single-site addressing. Specifically, we discuss protocols for efficient creation of an antiferromagnetic GHZ state, a class of matrix product states including a so-called Rydberg crystal and for the state transport of a single-qubit quantum state between two ends of a chain of atoms. We identify system parameters allowing for the operation of the protocols on timescales shorter than the lifetime of the Rydberg states while yielding high fidelity output states. We discuss the effect of positional disorder on the resulting states and comment on limitations due to other sources of noise such as radiative decay of the Rydberg states. The proposed protocols provide a testbed for benchmarking the performance of quantum information processing platforms based on Rydberg atoms.

Benchmark notch test for life prediction

NASA Technical Reports Server (NTRS)

Domas, P. A.; Sharpe, W. N.; Ward, M.; Yau, J. F.

1982-01-01

The laser Interferometric Strain Displacement Gage (ISDG) was used to measure local strains in notched Inconel 718 test bars subjected to six different load histories at 649 C (1200 F) and including effects of tensile and compressive hold periods. The measurements were compared to simplified Neuber notch analysis predictions of notch root stress and strain. The actual strains incurred at the root of a discontinuity in cyclically loaded test samples subjected to inelastic deformation at high temperature where creep deformations readily occur were determined. The steady state cyclic, stress-strain response at the root of the discontinuity was analyzed. Flat, double notched uniaxially loaded fatigue specimens manufactured from the nickel base, superalloy Inconel 718 were used. The ISDG was used to obtain cycle by cycle recordings of notch root strain during continuous and hold time cycling at 649 C. Comparisons to Neuber and finite element model analyses were made. The results obtained provide a benchmark data set in high technology design where notch fatigue life is the predominant component service life limitation.

Uav Cameras: Overview and Geometric Calibration Benchmark

NASA Astrophysics Data System (ADS)

Cramer, M.; Przybilla, H.-J.; Zurhorst, A.

2017-08-01

Different UAV platforms and sensors are used in mapping already, many of them equipped with (sometimes) modified cameras as known from the consumer market. Even though these systems normally fulfil their requested mapping accuracy, the question arises, which system performs best? This asks for a benchmark, to check selected UAV based camera systems in well-defined, reproducible environments. Such benchmark is tried within this work here. Nine different cameras used on UAV platforms, representing typical camera classes, are considered. The focus is laid on the geometry here, which is tightly linked to the process of geometrical calibration of the system. In most applications the calibration is performed in-situ, i.e. calibration parameters are obtained as part of the project data itself. This is often motivated because consumer cameras do not keep constant geometry, thus, cannot be seen as metric cameras. Still, some of the commercial systems are quite stable over time, as it was proven from repeated (terrestrial) calibrations runs. Already (pre-)calibrated systems may offer advantages, especially when the block geometry of the project does not allow for a stable and sufficient in-situ calibration. Especially for such scenario close to metric UAV cameras may have advantages. Empirical airborne test flights in a calibration field have shown how block geometry influences the estimated calibration parameters and how consistent the parameters from lab calibration can be reproduced.

A Field-Based Aquatic Life Benchmark for Conductivity in ...

EPA Pesticide Factsheets

EPA announced the availability of the final report, A Field-Based Aquatic Life Benchmark for Conductivity in Central Appalachian Streams. This report describes a method to characterize the relationship between the extirpation (the effective extinction) of invertebrate genera and salinity (measured as conductivity) and from that relationship derives a freshwater aquatic life benchmark. This benchmark of 300 µS/cm may be applied to waters in Appalachian streams that are dominated by calcium and magnesium salts of sulfate and bicarbonate at circum-neutral to mildly alkaline pH. This report provides scientific evidence for a conductivity benchmark in a specific region rather than for the entire United States.

Using benchmarks for radiation testing of microprocessors and FPGAs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quinn, Heather; Robinson, William H.; Rech, Paolo

Performance benchmarks have been used over the years to compare different systems. These benchmarks can be useful for researchers trying to determine how changes to the technology, architecture, or compiler affect the system's performance. No such standard exists for systems deployed into high radiation environments, making it difficult to assess whether changes in the fabrication process, circuitry, architecture, or software affect reliability or radiation sensitivity. In this paper, we propose a benchmark suite for high-reliability systems that is designed for field-programmable gate arrays and microprocessors. As a result, we describe the development process and report neutron test data for themore » hardware and software benchmarks.« less

Using benchmarks for radiation testing of microprocessors and FPGAs

DOE PAGES

Quinn, Heather; Robinson, William H.; Rech, Paolo; ...

2015-12-17

Performance benchmarks have been used over the years to compare different systems. These benchmarks can be useful for researchers trying to determine how changes to the technology, architecture, or compiler affect the system's performance. No such standard exists for systems deployed into high radiation environments, making it difficult to assess whether changes in the fabrication process, circuitry, architecture, or software affect reliability or radiation sensitivity. In this paper, we propose a benchmark suite for high-reliability systems that is designed for field-programmable gate arrays and microprocessors. As a result, we describe the development process and report neutron test data for themore » hardware and software benchmarks.« less

Standardised Benchmarking in the Quest for Orthologs

PubMed Central

Altenhoff, Adrian M.; Boeckmann, Brigitte; Capella-Gutierrez, Salvador; Dalquen, Daniel A.; DeLuca, Todd; Forslund, Kristoffer; Huerta-Cepas, Jaime; Linard, Benjamin; Pereira, Cécile; Pryszcz, Leszek P.; Schreiber, Fabian; Sousa da Silva, Alan; Szklarczyk, Damian; Train, Clément-Marie; Bork, Peer; Lecompte, Odile; von Mering, Christian; Xenarios, Ioannis; Sjölander, Kimmen; Juhl Jensen, Lars; Martin, Maria J.; Muffato, Matthieu; Gabaldón, Toni; Lewis, Suzanna E.; Thomas, Paul D.; Sonnhammer, Erik; Dessimoz, Christophe

2016-01-01

The identification of evolutionarily related genes across different species—orthologs in particular—forms the backbone of many comparative, evolutionary, and functional genomic analyses. Achieving high accuracy in orthology inference is thus essential. Yet the true evolutionary history of genes, required to ascertain orthology, is generally unknown. Furthermore, orthologs are used for very different applications across different phyla, with different requirements in terms of the precision-recall trade-off. As a result, assessing the performance of orthology inference methods remains difficult for both users and method developers. Here, we present a community effort to establish standards in orthology benchmarking and facilitate orthology benchmarking through an automated web-based service (http://orthology.benchmarkservice.org). Using this new service, we characterise the performance of 15 well-established orthology inference methods and resources on a battery of 20 different benchmarks. Standardised benchmarking provides a way for users to identify the most effective methods for the problem at hand, sets a minimal requirement for new tools and resources, and guides the development of more accurate orthology inference methods. PMID:27043882

Benchmarking CRISPR on-target sgRNA design.

PubMed

Yan, Jifang; Chuai, Guohui; Zhou, Chi; Zhu, Chenyu; Yang, Jing; Zhang, Chao; Gu, Feng; Xu, Han; Wei, Jia; Liu, Qi

2017-02-15

CRISPR (Clustered Regularly Interspaced Short Palindromic Repeats)-based gene editing has been widely implemented in various cell types and organisms. A major challenge in the effective application of the CRISPR system is the need to design highly efficient single-guide RNA (sgRNA) with minimal off-target cleavage. Several tools are available for sgRNA design, while limited tools were compared. In our opinion, benchmarking the performance of the available tools and indicating their applicable scenarios are important issues. Moreover, whether the reported sgRNA design rules are reproducible across different sgRNA libraries, cell types and organisms remains unclear. In our study, a systematic and unbiased benchmark of the sgRNA predicting efficacy was performed on nine representative on-target design tools, based on six benchmark data sets covering five different cell types. The benchmark study presented here provides novel quantitative insights into the available CRISPR tools. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Algorithm and Architecture Independent Benchmarking with SEAK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tallent, Nathan R.; Manzano Franco, Joseph B.; Gawande, Nitin A.

2016-05-23

Many applications of high performance embedded computing are limited by performance or power bottlenecks. We have designed the Suite for Embedded Applications & Kernels (SEAK), a new benchmark suite, (a) to capture these bottlenecks in a way that encourages creative solutions; and (b) to facilitate rigorous, objective, end-user evaluation for their solutions. To avoid biasing solutions toward existing algorithms, SEAK benchmarks use a mission-centric (abstracted from a particular algorithm) and goal-oriented (functional) specification. To encourage solutions that are any combination of software or hardware, we use an end-user black-box evaluation that can capture tradeoffs between performance, power, accuracy, size, andmore » weight. The tradeoffs are especially informative for procurement decisions. We call our benchmarks future proof because each mission-centric interface and evaluation remains useful despite shifting algorithmic preferences. It is challenging to create both concise and precise goal-oriented specifications for mission-centric problems. This paper describes the SEAK benchmark suite and presents an evaluation of sample solutions that highlights power and performance tradeoffs.« less

Quality management benchmarking: FDA compliance in pharmaceutical industry.

PubMed

Jochem, Roland; Landgraf, Katja

2010-01-01

By analyzing and comparing industry and business best practice, processes can be optimized and become more successful mainly because efficiency and competitiveness increase. This paper aims to focus on some examples. Case studies are used to show knowledge exchange in the pharmaceutical industry. Best practice solutions were identified in two companies using a benchmarking method and five-stage model. Despite large administrations, there is much potential regarding business process organization. This project makes it possible for participants to fully understand their business processes. The benchmarking method gives an opportunity to critically analyze value chains (a string of companies or players working together to satisfy market demands for a special product). Knowledge exchange is interesting for companies that like to be global players. Benchmarking supports information exchange and improves competitive ability between different enterprises. Findings suggest that the five-stage model improves efficiency and effectiveness. Furthermore, the model increases the chances for reaching targets. The method gives security to partners that did not have benchmarking experience. The study identifies new quality management procedures. Process management and especially benchmarking is shown to support pharmaceutical industry improvements.

Thought Experiment to Examine Benchmark Performance for Fusion Nuclear Data

NASA Astrophysics Data System (ADS)

Murata, Isao; Ohta, Masayuki; Kusaka, Sachie; Sato, Fuminobu; Miyamaru, Hiroyuki

2017-09-01

There are many benchmark experiments carried out so far with DT neutrons especially aiming at fusion reactor development. These integral experiments seemed vaguely to validate the nuclear data below 14 MeV. However, no precise studies exist now. The author's group thus started to examine how well benchmark experiments with DT neutrons can play a benchmarking role for energies below 14 MeV. Recently, as a next phase, to generalize the above discussion, the energy range was expanded to the entire region. In this study, thought experiments with finer energy bins have thus been conducted to discuss how to generally estimate performance of benchmark experiments. As a result of thought experiments with a point detector, the sensitivity for a discrepancy appearing in the benchmark analysis is "equally" due not only to contribution directly conveyed to the deterctor, but also due to indirect contribution of neutrons (named (A)) making neutrons conveying the contribution, indirect controbution of neutrons (B) making the neutrons (A) and so on. From this concept, it would become clear from a sensitivity analysis in advance how well and which energy nuclear data could be benchmarked with a benchmark experiment.

Neutron Reference Benchmark Field Specification: ACRR Free-Field Environment (ACRR-FF-CC-32-CL).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vega, Richard Manuel; Parma, Edward J.; Griffin, Patrick J.

2015-07-01

This report was put together to support the International Atomic Energy Agency (IAEA) REAL- 2016 activity to validate the dosimetry community’s ability to use a consistent set of activation data and to derive consistent spectral characterizations. The report captures details of integral measurements taken in the Annular Core Research Reactor (ACRR) central cavity free-field reference neutron benchmark field. The field is described and an “a priori” calculated neutron spectrum is reported, based on MCNP6 calculations, and a subject matter expert (SME) based covariance matrix is given for this “a priori” spectrum. The results of 31 integral dosimetry measurements in themore » neutron field are reported.« less

Cross-industry benchmarking: is it applicable to the operating room?

PubMed

Marco, A P; Hart, S

2001-01-01

The use of benchmarking has been growing in nonmedical industries. This concept is being increasingly applied to medicine as the industry strives to improve quality and improve financial performance. Benchmarks can be either internal (set by the institution) or external (use other's performance as a goal). In some industries, benchmarking has crossed industry lines to identify breakthroughs in thinking. In this article, we examine whether the airline industry can be used as a source of external process benchmarking for the operating room.

Cloud-Based Evaluation of Anatomical Structure Segmentation and Landmark Detection Algorithms: VISCERAL Anatomy Benchmarks.

PubMed

Jimenez-Del-Toro, Oscar; Muller, Henning; Krenn, Markus; Gruenberg, Katharina; Taha, Abdel Aziz; Winterstein, Marianne; Eggel, Ivan; Foncubierta-Rodriguez, Antonio; Goksel, Orcun; Jakab, Andras; Kontokotsios, Georgios; Langs, Georg; Menze, Bjoern H; Salas Fernandez, Tomas; Schaer, Roger; Walleyo, Anna; Weber, Marc-Andre; Dicente Cid, Yashin; Gass, Tobias; Heinrich, Mattias; Jia, Fucang; Kahl, Fredrik; Kechichian, Razmig; Mai, Dominic; Spanier, Assaf B; Vincent, Graham; Wang, Chunliang; Wyeth, Daniel; Hanbury, Allan

2016-11-01

Variations in the shape and appearance of anatomical structures in medical images are often relevant radiological signs of disease. Automatic tools can help automate parts of this manual process. A cloud-based evaluation framework is presented in this paper including results of benchmarking current state-of-the-art medical imaging algorithms for anatomical structure segmentation and landmark detection: the VISCERAL Anatomy benchmarks. The algorithms are implemented in virtual machines in the cloud where participants can only access the training data and can be run privately by the benchmark administrators to objectively compare their performance in an unseen common test set. Overall, 120 computed tomography and magnetic resonance patient volumes were manually annotated to create a standard Gold Corpus containing a total of 1295 structures and 1760 landmarks. Ten participants contributed with automatic algorithms for the organ segmentation task, and three for the landmark localization task. Different algorithms obtained the best scores in the four available imaging modalities and for subsets of anatomical structures. The annotation framework, resulting data set, evaluation setup, results and performance analysis from the three VISCERAL Anatomy benchmarks are presented in this article. Both the VISCERAL data set and Silver Corpus generated with the fusion of the participant algorithms on a larger set of non-manually-annotated medical images are available to the research community.

Role of the standard deviation in the estimation of benchmark doses with continuous data.

PubMed

Gaylor, David W; Slikker, William

2004-12-01

For continuous data, risk is defined here as the proportion of animals with values above a large percentile, e.g., the 99th percentile or below the 1st percentile, for the distribution of values among control animals. It is known that reducing the standard deviation of measurements through improved experimental techniques will result in less stringent (higher) doses for the lower confidence limit on the benchmark dose that is estimated to produce a specified risk of animals with abnormal levels for a biological effect. Thus, a somewhat larger (less stringent) lower confidence limit is obtained that may be used as a point of departure for low-dose risk assessment. It is shown in this article that it is important for the benchmark dose to be based primarily on the standard deviation among animals, s(a), apart from the standard deviation of measurement errors, s(m), within animals. If the benchmark dose is incorrectly based on the overall standard deviation among average values for animals, which includes measurement error variation, the benchmark dose will be overestimated and the risk will be underestimated. The bias increases as s(m) increases relative to s(a). The bias is relatively small if s(m) is less than one-third of s(a), a condition achieved in most experimental designs.

Benchmarking a Soil Moisture Data Assimilation System for Agricultural Drought Monitoring

NASA Technical Reports Server (NTRS)

Hun, Eunjin; Crow, Wade T.; Holmes, Thomas; Bolten, John

2014-01-01

Despite considerable interest in the application of land surface data assimilation systems (LDAS) for agricultural drought applications, relatively little is known about the large-scale performance of such systems and, thus, the optimal methodological approach for implementing them. To address this need, this paper evaluates an LDAS for agricultural drought monitoring by benchmarking individual components of the system (i.e., a satellite soil moisture retrieval algorithm, a soil water balance model and a sequential data assimilation filter) against a series of linear models which perform the same function (i.e., have the same basic inputoutput structure) as the full system component. Benchmarking is based on the calculation of the lagged rank cross-correlation between the normalized difference vegetation index (NDVI) and soil moisture estimates acquired for various components of the system. Lagged soil moistureNDVI correlations obtained using individual LDAS components versus their linear analogs reveal the degree to which non-linearities andor complexities contained within each component actually contribute to the performance of the LDAS system as a whole. Here, a particular system based on surface soil moisture retrievals from the Land Parameter Retrieval Model (LPRM), a two-layer Palmer soil water balance model and an Ensemble Kalman filter (EnKF) is benchmarked. Results suggest significant room for improvement in each component of the system.

Atomic resolution images of graphite in air

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grigg, D.A.; Shedd, G.M.; Griffis, D.

One sample used for proof of operation for atomic resolution in STM is highly oriented pyrolytic graphite (HOPG). This sample has been imaged with many different STM`s obtaining similar results. Atomic resolution images of HOPG have now been obtained using an STM designed and built at the Precision Engineering Center. This paper discusses the theoretical predictions and experimental results obtained in imaging of HOPG.

Benchmark solutions for the galactic ion transport equations: Energy and spatially dependent problems

NASA Technical Reports Server (NTRS)

Ganapol, Barry D.; Townsend, Lawrence W.; Wilson, John W.

1989-01-01

Nontrivial benchmark solutions are developed for the galactic ion transport (GIT) equations in the straight-ahead approximation. These equations are used to predict potential radiation hazards in the upper atmosphere and in space. Two levels of difficulty are considered: (1) energy independent, and (2) spatially independent. The analysis emphasizes analytical methods never before applied to the GIT equations. Most of the representations derived have been numerically implemented and compared to more approximate calculations. Accurate ion fluxes are obtained (3 to 5 digits) for nontrivial sources. For monoenergetic beams, both accurate doses and fluxes are found. The benchmarks presented are useful in assessing the accuracy of transport algorithms designed to accommodate more complex radiation protection problems. In addition, these solutions can provide fast and accurate assessments of relatively simple shield configurations.

Statistical Analysis of NAS Parallel Benchmarks and LINPACK Results

NASA Technical Reports Server (NTRS)

Meuer, Hans-Werner; Simon, Horst D.; Strohmeier, Erich; Lasinski, T. A. (Technical Monitor)

1994-01-01

In the last three years extensive performance data have been reported for parallel machines both based on the NAS Parallel Benchmarks, and on LINPACK. In this study we have used the reported benchmark results and performed a number of statistical experiments using factor, cluster, and regression analyses. In addition to the performance results of LINPACK and the eight NAS parallel benchmarks, we have also included peak performance of the machine, and the LINPACK n and n(sub 1/2) values. Some of the results and observations can be summarized as follows: 1) All benchmarks are strongly correlated with peak performance. 2) LINPACK and EP have each a unique signature. 3) The remaining NPB can grouped into three groups as follows: (CG and IS), (LU and SP), and (MG, FT, and BT). Hence three (or four with EP) benchmarks are sufficient to characterize the overall NPB performance. Our poster presentation will follow a standard poster format, and will present the data of our statistical analysis in detail.

Performance Characteristics of the Multi-Zone NAS Parallel Benchmarks

NASA Technical Reports Server (NTRS)

Jin, Haoqiang; VanderWijngaart, Rob F.

2003-01-01

We describe a new suite of computational benchmarks that models applications featuring multiple levels of parallelism. Such parallelism is often available in realistic flow computations on systems of grids, but had not previously been captured in bench-marks. The new suite, named NPB Multi-Zone, is extended from the NAS Parallel Benchmarks suite, and involves solving the application benchmarks LU, BT and SP on collections of loosely coupled discretization meshes. The solutions on the meshes are updated independently, but after each time step they exchange boundary value information. This strategy provides relatively easily exploitable coarse-grain parallelism between meshes. Three reference implementations are available: one serial, one hybrid using the Message Passing Interface (MPI) and OpenMP, and another hybrid using a shared memory multi-level programming model (SMP+OpenMP). We examine the effectiveness of hybrid parallelization paradigms in these implementations on three different parallel computers. We also use an empirical formula to investigate the performance characteristics of the multi-zone benchmarks.

NACA0012 benchmark model experimental flutter results with unsteady pressure distributions

NASA Technical Reports Server (NTRS)

Rivera, Jose A., Jr.; Dansberry, Bryan E.; Bennett, Robert M.; Durham, Michael H.; Silva, Walter A.

1992-01-01

The Structural Dynamics Division at NASA Langley Research Center has started a wind tunnel activity referred to as the Benchmark Models Program. The primary objective of this program is to acquire measured dynamic instability and corresponding pressure data that will be useful for developing and evaluating aeroelastic type computational fluid dynamics codes currently in use or under development. The program is a multi-year activity that will involve testing of several different models to investigate various aeroelastic phenomena. This paper describes results obtained from a second wind tunnel test of the first model in the Benchmark Models Program. This first model consisted of a rigid semispan wing having a rectangular planform and a NACA 0012 airfoil shape which was mounted on a flexible two degree of freedom mount system. Experimental flutter boundaries and corresponding unsteady pressure distribution data acquired over two model chords located at the 60 and 95 percent span stations are presented.

Length of stay benchmarks for inpatient rehabilitation after stroke.

PubMed

Meyer, Matthew; Britt, Eileen; McHale, Heather A; Teasell, Robert

2012-01-01

In Canada, no standardized benchmarks for length of stay (LOS) have been established for post-stroke inpatient rehabilitation. This paper describes the development of a severity specific median length of stay benchmarking strategy, assessment of its impact after one year of implementation in a Canadian rehabilitation hospital, and establishment of updated benchmarks that may be useful for comparison with other facilities across Canada. Patient data were retrospectively assessed for all patients admitted to a single post-acute stroke rehabilitation unit in Ontario, Canada between April 2005 and March 2008. Rehabilitation Patient Groups (RPGs) were used to establish stratified median length of stay benchmarks for each group that were incorporated into team rounds beginning in October 2009. Benchmark impact was assessed using mean LOS, FIM(®) gain, and discharge destination for each RPG group, collected prospectively for one year, compared against similar information from the previous calendar year. Benchmarks were then adjusted accordingly for future use. Between October 2009 and September 2010, a significant reduction in average LOS was noted compared to the previous year (35.3 vs. 41.2 days; p < 0.05). Reductions in LOS were noted in each RPG group including statistically significant reductions in 4 of the 7 groups. As intended, reductions in LOS were achieved with no significant reduction in mean FIM(®) gain or proportion of patients discharged home compared to the previous year. Adjusted benchmarks for LOS ranged from 13 to 48 days depending on the RPG group. After a single year of implementation, severity specific benchmarks helped the rehabilitation team reduce LOS while maintaining the same levels of functional gain and achieving the same rate of discharge to the community. © 2012 Informa UK, Ltd.

Recent trends in precision measurements of atomic and nuclear properties with lasers and ion traps

NASA Astrophysics Data System (ADS)

Block, Michael

2017-11-01

The X. international workshop on "Application of Lasers and Storage Devices in Atomic Nuclei Research" took place in Poznan in May 2016. It addressed the latest experimental and theoretical achievements in laser and ion trap-based investigations of radionuclides, highly charged ions and antiprotons. The precise determination of atomic and nuclear properties provides a stringent benchmark for theoretical models and eventually leads to a better understanding of the underlying fundamental interactions and symmetries. This article addresses some general trends in this field and highlights select recent achievements presented at the workshop. Many of these are covered in more detail within the individual contributions to this special issue of Hyperfine Interactions.

Hirshfeld atom refinement

PubMed Central

Capelli, Silvia C.; Bürgi, Hans-Beat; Dittrich, Birger; Grabowsky, Simon; Jayatilaka, Dylan

2014-01-01

Hirshfeld atom refinement (HAR) is a method which determines structural parameters from single-crystal X-ray diffraction data by using an aspherical atom partitioning of tailor-made ab initio quantum mechanical molecular electron densities without any further approximation. Here the original HAR method is extended by implementing an iterative procedure of successive cycles of electron density calculations, Hirshfeld atom scattering factor calculations and structural least-squares refinements, repeated until convergence. The importance of this iterative procedure is illustrated via the example of crystalline ammonia. The new HAR method is then applied to X-ray diffraction data of the dipeptide Gly–l-Ala measured at 12, 50, 100, 150, 220 and 295 K, using Hartree–Fock and BLYP density functional theory electron densities and three different basis sets. All positions and anisotropic displacement parameters (ADPs) are freely refined without constraints or restraints – even those for hydrogen atoms. The results are systematically compared with those from neutron diffraction experiments at the temperatures 12, 50, 150 and 295 K. Although non-hydrogen-atom ADPs differ by up to three combined standard uncertainties (csu’s), all other structural parameters agree within less than 2 csu’s. Using our best calculations (BLYP/cc-pVTZ, recommended for organic molecules), the accuracy of determining bond lengths involving hydrogen atoms from HAR is better than 0.009 Å for temperatures of 150 K or below; for hydrogen-atom ADPs it is better than 0.006 Å2 as judged from the mean absolute X-ray minus neutron differences. These results are among the best ever obtained. Remarkably, the precision of determining bond lengths and ADPs for the hydrogen atoms from the HAR procedure is comparable with that from the neutron measurements – an outcome which is obtained with a routinely achievable resolution of the X-ray data of 0.65 Å. PMID:25295177

Benchmarking biology research organizations using a new, dedicated tool.

PubMed

van Harten, Willem H; van Bokhorst, Leonard; van Luenen, Henri G A M

2010-02-01

International competition forces fundamental research organizations to assess their relative performance. We present a benchmark tool for scientific research organizations where, contrary to existing models, the group leader is placed in a central position within the organization. We used it in a pilot benchmark study involving six research institutions. Our study shows that data collection and data comparison based on this new tool can be achieved. It proved possible to compare relative performance and organizational characteristics and to generate suggestions for improvement for most participants. However, strict definitions of the parameters used for the benchmark and a thorough insight into the organization of each of the benchmark partners is required to produce comparable data and draw firm conclusions.

EPA and EFSA approaches for Benchmark Dose modeling

EPA Science Inventory

Benchmark dose (BMD) modeling has become the preferred approach in the analysis of toxicological dose-response data for the purpose of deriving human health toxicity values. The software packages most often used are Benchmark Dose Software (BMDS, developed by EPA) and PROAST (de...

Discovering and Implementing Best Practices to Strengthen SEAs: Collaborative Benchmarking

ERIC Educational Resources Information Center

Building State Capacity and Productivity Center, 2013

2013-01-01

This paper is written for state educational agency (SEA) leaders who are considering the benefits of collaborative benchmarking, and it addresses the following questions: (1) What does benchmarking of best practices entail?; (2) How does "collaborative benchmarking" enhance the process?; (3) How do SEAs control the process so that "their" needs…

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 24 2012-07-01 2012-07-01 false How is the disinfection benchmark... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection benchmark calculated? If your system is making a significant change to its disinfection practice, it must...

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false How is the disinfection benchmark... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection benchmark calculated? If your system is making a significant change to its disinfection practice, it must...

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 24 2013-07-01 2013-07-01 false How is the disinfection benchmark... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection benchmark calculated? If your system is making a significant change to its disinfection practice, it must...

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 23 2011-07-01 2011-07-01 false How is the disinfection benchmark... Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection benchmark calculated? If your system is making a significant change to its disinfection practice, it must...

Benchmarking can add up for healthcare accounting.

PubMed

Czarnecki, M T

1994-09-01

In 1993, a healthcare accounting and finance benchmarking survey of hospital and nonhospital organizations gathered statistics about key common performance areas. A low response did not allow for statistically significant findings, but the survey identified performance measures that can be used in healthcare financial management settings. This article explains the benchmarking process and examines some of the 1993 study's findings.

Benchmarking in Thoracic Surgery. Third Edition.

PubMed

Freixinet Gilart, Jorge; Varela Simó, Gonzalo; Rodríguez Suárez, Pedro; Embún Flor, Raúl; Rivas de Andrés, Juan José; de la Torre Bravos, Mercedes; Molins López-Rodó, Laureano; Pac Ferrer, Joaquín; Izquierdo Elena, José Miguel; Baschwitz, Benno; López de Castro, Pedro E; Fibla Alfara, Juan José; Hernando Trancho, Florentino; Carvajal Carrasco, Ángel; Canalís Arrayás, Emili; Salvatierra Velázquez, Ángel; Canela Cardona, Mercedes; Torres Lanzas, Juan; Moreno Mata, Nicolás

2016-04-01

Benchmarking entails continuous comparison of efficacy and quality among products and activities, with the primary objective of achieving excellence. To analyze the results of benchmarking performed in 2013 on clinical practices undertaken in 2012 in 17 Spanish thoracic surgery units. Study data were obtained from the basic minimum data set for hospitalization, registered in 2012. Data from hospital discharge reports were submitted by the participating groups, but staff from the corresponding departments did not intervene in data collection. Study cases all involved hospital discharges recorded in the participating sites. Episodes included were respiratory surgery (Major Diagnostic Category 04, Surgery), and those of the thoracic surgery unit. Cases were labelled using codes from the International Classification of Diseases, 9th revision, Clinical Modification. The refined diagnosis-related groups classification was used to evaluate differences in severity and complexity of cases. General parameters (number of cases, mean stay, complications, readmissions, mortality, and activity) varied widely among the participating groups. Specific interventions (lobectomy, pneumonectomy, atypical resections, and treatment of pneumothorax) also varied widely. As in previous editions, practices among participating groups varied considerably. Some areas for improvement emerge: admission processes need to be standardized to avoid urgent admissions and to improve pre-operative care; hospital discharges should be streamlined and discharge reports improved by including all procedures and complications. Some units have parameters which deviate excessively from the norm, and these sites need to review their processes in depth. Coding of diagnoses and comorbidities is another area where improvement is needed. Copyright © 2015 SEPAR. Published by Elsevier Espana. All rights reserved.

Benchmarks for Evaluation of Distributed Denial of Service (DDOS)

DTIC Science & Technology

2008-01-01

publications: [1] E. Arikan , Attack Profiling for DDoS Benchmarks, MS Thesis, University of Delaware, August 2006. [2] J. Mirkovic, A. Hussain, B. Wilson...Sigmetrics 2007, June 2007 [5] J. Mirkovic, E. Arikan , S. Wei, S. Fahmy, R. Thomas, and P. Reiher Benchmarks for DDoS Defense Evaluation, Proceedings of the...Security Experimentation, June 2006. [9] J. Mirkovic, E. Arikan , S. Wei, S. Fahmy, R. Thomas, P. Reiher, Benchmarks for DDoS Defense Evaluation

Benchmark matrix and guide: Part II.

PubMed

1991-01-01

In the last issue of the Journal of Quality Assurance (September/October 1991, Volume 13, Number 5, pp. 14-19), the benchmark matrix developed by Headquarters Air Force Logistics Command was published. Five horizontal levels on the matrix delineate progress in TQM: business as usual, initiation, implementation, expansion, and integration. The six vertical categories that are critical to the success of TQM are leadership, structure, training, recognition, process improvement, and customer focus. In this issue, "Benchmark Matrix and Guide: Part II" will show specifically how to apply the categories of leadership, structure, and training to the benchmark matrix progress levels. At the intersection of each category and level, specific behavior objectives are listed with supporting behaviors and guidelines. Some categories will have objectives that are relatively easy to accomplish, allowing quick progress from one level to the next. Other categories will take considerable time and effort to complete. In the next issue, Part III of this series will focus on recognition, process improvement, and customer focus.

A Competitive Benchmarking Study of Noncredit Program Administration.

ERIC Educational Resources Information Center

Alstete, Jeffrey W.

1996-01-01

A benchmarking project to measure administrative processes and financial ratios received 57 usable replies from 300 noncredit continuing education programs. Programs with strong financial surpluses were identified and their processes benchmarked (including response to inquiries, registrants, registrant/staff ratio, new courses, class size,…

The Learning Organisation: Results of a Benchmarking Study.

ERIC Educational Resources Information Center

Zairi, Mohamed

1999-01-01

Learning in corporations was assessed using these benchmarks: core qualities of creative organizations, characteristic of organizational creativity, attributes of flexible organizations, use of diversity and conflict, creative human resource management systems, and effective and successful teams. These benchmarks are key elements of the learning…

Surveys and Benchmarks

ERIC Educational Resources Information Center

Bers, Trudy

2012-01-01

Surveys and benchmarks continue to grow in importance for community colleges in response to several factors. One is the press for accountability, that is, for colleges to report the outcomes of their programs and services to demonstrate their quality and prudent use of resources, primarily to external constituents and governing boards at the state…

The Model Averaging for Dichotomous Response Benchmark Dose (MADr-BMD) Tool

EPA Pesticide Factsheets

Providing quantal response models, which are also used in the U.S. EPA benchmark dose software suite, and generates a model-averaged dose response model to generate benchmark dose and benchmark dose lower bound estimates.

Developing a benchmark for emotional analysis of music

PubMed Central

Yang, Yi-Hsuan; Soleymani, Mohammad

2017-01-01

Music emotion recognition (MER) field rapidly expanded in the last decade. Many new methods and new audio features are developed to improve the performance of MER algorithms. However, it is very difficult to compare the performance of the new methods because of the data representation diversity and scarcity of publicly available data. In this paper, we address these problems by creating a data set and a benchmark for MER. The data set that we release, a MediaEval Database for Emotional Analysis in Music (DEAM), is the largest available data set of dynamic annotations (valence and arousal annotations for 1,802 songs and song excerpts licensed under Creative Commons with 2Hz time resolution). Using DEAM, we organized the ‘Emotion in Music’ task at MediaEval Multimedia Evaluation Campaign from 2013 to 2015. The benchmark attracted, in total, 21 active teams to participate in the challenge. We analyze the results of the benchmark: the winning algorithms and feature-sets. We also describe the design of the benchmark, the evaluation procedures and the data cleaning and transformations that we suggest. The results from the benchmark suggest that the recurrent neural network based approaches combined with large feature-sets work best for dynamic MER. PMID:28282400

Decoys Selection in Benchmarking Datasets: Overview and Perspectives

PubMed Central

Réau, Manon; Langenfeld, Florent; Zagury, Jean-François; Lagarde, Nathalie; Montes, Matthieu

2018-01-01

Virtual Screening (VS) is designed to prospectively help identifying potential hits, i.e., compounds capable of interacting with a given target and potentially modulate its activity, out of large compound collections. Among the variety of methodologies, it is crucial to select the protocol that is the most adapted to the query/target system under study and that yields the most reliable output. To this aim, the performance of VS methods is commonly evaluated and compared by computing their ability to retrieve active compounds in benchmarking datasets. The benchmarking datasets contain a subset of known active compounds together with a subset of decoys, i.e., assumed non-active molecules. The composition of both the active and the decoy compounds subsets is critical to limit the biases in the evaluation of the VS methods. In this review, we focus on the selection of decoy compounds that has considerably changed over the years, from randomly selected compounds to highly customized or experimentally validated negative compounds. We first outline the evolution of decoys selection in benchmarking databases as well as current benchmarking databases that tend to minimize the introduction of biases, and secondly, we propose recommendations for the selection and the design of benchmarking datasets. PMID:29416509

Developing a benchmark for emotional analysis of music.

PubMed

Aljanaki, Anna; Yang, Yi-Hsuan; Soleymani, Mohammad

2017-01-01

Music emotion recognition (MER) field rapidly expanded in the last decade. Many new methods and new audio features are developed to improve the performance of MER algorithms. However, it is very difficult to compare the performance of the new methods because of the data representation diversity and scarcity of publicly available data. In this paper, we address these problems by creating a data set and a benchmark for MER. The data set that we release, a MediaEval Database for Emotional Analysis in Music (DEAM), is the largest available data set of dynamic annotations (valence and arousal annotations for 1,802 songs and song excerpts licensed under Creative Commons with 2Hz time resolution). Using DEAM, we organized the 'Emotion in Music' task at MediaEval Multimedia Evaluation Campaign from 2013 to 2015. The benchmark attracted, in total, 21 active teams to participate in the challenge. We analyze the results of the benchmark: the winning algorithms and feature-sets. We also describe the design of the benchmark, the evaluation procedures and the data cleaning and transformations that we suggest. The results from the benchmark suggest that the recurrent neural network based approaches combined with large feature-sets work best for dynamic MER.

A large-scale benchmark of gene prioritization methods.

PubMed

Guala, Dimitri; Sonnhammer, Erik L L

2017-04-21

In order to maximize the use of results from high-throughput experimental studies, e.g. GWAS, for identification and diagnostics of new disease-associated genes, it is important to have properly analyzed and benchmarked gene prioritization tools. While prospective benchmarks are underpowered to provide statistically significant results in their attempt to differentiate the performance of gene prioritization tools, a strategy for retrospective benchmarking has been missing, and new tools usually only provide internal validations. The Gene Ontology(GO) contains genes clustered around annotation terms. This intrinsic property of GO can be utilized in construction of robust benchmarks, objective to the problem domain. We demonstrate how this can be achieved for network-based gene prioritization tools, utilizing the FunCoup network. We use cross-validation and a set of appropriate performance measures to compare state-of-the-art gene prioritization algorithms: three based on network diffusion, NetRank and two implementations of Random Walk with Restart, and MaxLink that utilizes network neighborhood. Our benchmark suite provides a systematic and objective way to compare the multitude of available and future gene prioritization tools, enabling researchers to select the best gene prioritization tool for the task at hand, and helping to guide the development of more accurate methods.

NAS Grid Benchmarks: A Tool for Grid Space Exploration

NASA Technical Reports Server (NTRS)

Frumkin, Michael; VanderWijngaart, Rob F.; Biegel, Bryan (Technical Monitor)

2001-01-01

We present an approach for benchmarking services provided by computational Grids. It is based on the NAS Parallel Benchmarks (NPB) and is called NAS Grid Benchmark (NGB) in this paper. We present NGB as a data flow graph encapsulating an instance of an NPB code in each graph node, which communicates with other nodes by sending/receiving initialization data. These nodes may be mapped to the same or different Grid machines. Like NPB, NGB will specify several different classes (problem sizes). NGB also specifies the generic Grid services sufficient for running the bench-mark. The implementor has the freedom to choose any specific Grid environment. However, we describe a reference implementation in Java, and present some scenarios for using NGB.

Seismo-acoustic ray model benchmarking against experimental tank data.

PubMed

Camargo Rodríguez, Orlando; Collis, Jon M; Simpson, Harry J; Ey, Emanuel; Schneiderwind, Joseph; Felisberto, Paulo

2012-08-01

Acoustic predictions of the recently developed traceo ray model, which accounts for bottom shear properties, are benchmarked against tank experimental data from the EPEE-1 and EPEE-2 (Elastic Parabolic Equation Experiment) experiments. Both experiments are representative of signal propagation in a Pekeris-like shallow-water waveguide over a non-flat isotropic elastic bottom, where significant interaction of the signal with the bottom can be expected. The benchmarks show, in particular, that the ray model can be as accurate as a parabolic approximation model benchmarked in similar conditions. The results of benchmarking are important, on one side, as a preliminary experimental validation of the model and, on the other side, demonstrates the reliability of the ray approach for seismo-acoustic applications.

Simple Benchmark Specifications for Space Radiation Protection

NASA Technical Reports Server (NTRS)

Singleterry, Robert C. Jr.; Aghara, Sukesh K.

2013-01-01

This report defines space radiation benchmark specifications. This specification starts with simple, monoenergetic, mono-directional particles on slabs and progresses to human models in spacecraft. This report specifies the models and sources needed to what the team performing the benchmark needs to produce in a report. Also included are brief descriptions of how OLTARIS, the NASA Langley website for space radiation analysis, performs its analysis.

PHISICS/RELAP5-3D RESULTS FOR EXERCISES II-1 AND II-2 OF THE OECD/NEA MHTGR-350 BENCHMARK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strydom, Gerhard

2016-03-01

The Idaho National Laboratory (INL) Advanced Reactor Technologies (ART) High-Temperature Gas-Cooled Reactor (HTGR) Methods group currently leads the Modular High-Temperature Gas-Cooled Reactor (MHTGR) 350 benchmark. The benchmark consists of a set of lattice-depletion, steady-state, and transient problems that can be used by HTGR simulation groups to assess the performance of their code suites. The paper summarizes the results obtained for the first two transient exercises defined for Phase II of the benchmark. The Parallel and Highly Innovative Simulation for INL Code System (PHISICS), coupled with the INL system code RELAP5-3D, was used to generate the results for the Depressurized Conductionmore » Cooldown (DCC) (exercise II-1a) and Pressurized Conduction Cooldown (PCC) (exercise II-2) transients. These exercises require the time-dependent simulation of coupled neutronics and thermal-hydraulics phenomena, and utilize the steady-state solution previously obtained for exercise I-3 of Phase I. This paper also includes a comparison of the benchmark results obtained with a traditional system code “ring” model against a more detailed “block” model that include kinetics feedback on an individual block level and thermal feedbacks on a triangular sub-mesh. The higher spatial fidelity that can be obtained by the block model is illustrated with comparisons of the maximum fuel temperatures, especially in the case of natural convection conditions that dominate the DCC and PCC events. Differences up to 125 K (or 10%) were observed between the ring and block model predictions of the DCC transient, mostly due to the block model’s capability of tracking individual block decay powers and more detailed helium flow distributions. In general, the block model only required DCC and PCC calculation times twice as long as the ring models, and it therefore seems that the additional development and calculation time required for the block model could be worth the gain that can

IT-benchmarking of clinical workflows: concept, implementation, and evaluation.

PubMed

Thye, Johannes; Straede, Matthias-Christopher; Liebe, Jan-David; Hübner, Ursula

2014-01-01

Due to the emerging evidence of health IT as opportunity and risk for clinical workflows, health IT must undergo a continuous measurement of its efficacy and efficiency. IT-benchmarks are a proven means for providing this information. The aim of this study was to enhance the methodology of an existing benchmarking procedure by including, in particular, new indicators of clinical workflows and by proposing new types of visualisation. Drawing on the concept of information logistics, we propose four workflow descriptors that were applied to four clinical processes. General and specific indicators were derived from these descriptors and processes. 199 chief information officers (CIOs) took part in the benchmarking. These hospitals were assigned to reference groups of a similar size and ownership from a total of 259 hospitals. Stepwise and comprehensive feedback was given to the CIOs. Most participants who evaluated the benchmark rated the procedure as very good, good, or rather good (98.4%). Benchmark information was used by CIOs for getting a general overview, advancing IT, preparing negotiations with board members, and arguing for a new IT project.

Benchmarking the cost efficiency of community care in Australian child and adolescent mental health services: implications for future benchmarking.

PubMed

Furber, Gareth; Brann, Peter; Skene, Clive; Allison, Stephen

2011-06-01

The purpose of this study was to benchmark the cost efficiency of community care across six child and adolescent mental health services (CAMHS) drawn from different Australian states. Organizational, contact and outcome data from the National Mental Health Benchmarking Project (NMHBP) data-sets were used to calculate cost per "treatment hour" and cost per episode for the six participating organizations. We also explored the relationship between intake severity as measured by the Health of the Nations Outcome Scales for Children and Adolescents (HoNOSCA) and cost per episode. The average cost per treatment hour was $223, with cost differences across the six services ranging from a mean of $156 to $273 per treatment hour. The average cost per episode was $3349 (median $1577) and there were significant differences in the CAMHS organizational medians ranging from $388 to $7076 per episode. HoNOSCA scores explained at best 6% of the cost variance per episode. These large cost differences indicate that community CAMHS have the potential to make substantial gains in cost efficiency through collaborative benchmarking. Benchmarking forums need considerable financial and business expertise for detailed comparison of business models for service provision.

Atom Interferometry in a Warm Vapor

DOE PAGES

Biedermann, G. W.; McGuinness, H. J.; Rakholia, A. V.; ...

2017-04-17

Here, we demonstrate matter-wave interference in a warm vapor of rubidium atoms. Established approaches to light-pulse atom interferometry rely on laser cooling to concentrate a large ensemble of atoms into a velocity class resonant with the atom optical light pulse. In our experiment, we show that clear interference signals may be obtained without laser cooling. This effect relies on the Doppler selectivity of the atom interferometer resonance. Lastly, this interferometer may be configured to measure accelerations, and we demonstrate that multiple interferometers may be operated simultaneously by addressing multiple velocity classes.

Atom and Bond Fukui Functions and Matrices: A Hirshfeld-I Atoms-in-Molecule Approach.

PubMed

Oña, Ofelia B; De Clercq, Olivier; Alcoba, Diego R; Torre, Alicia; Lain, Luis; Van Neck, Dimitri; Bultinck, Patrick

2016-09-19

The Fukui function is often used in its atom-condensed form by isolating it from the molecular Fukui function using a chosen weight function for the atom in the molecule. Recently, Fukui functions and matrices for both atoms and bonds separately were introduced for semiempirical and ab initio levels of theory using Hückel and Mulliken atoms-in-molecule models. In this work, a double partitioning method of the Fukui matrix is proposed within the Hirshfeld-I atoms-in-molecule framework. Diagonalizing the resulting atomic and bond matrices gives eigenvalues and eigenvectors (Fukui orbitals) describing the reactivity of atoms and bonds. The Fukui function is the diagonal element of the Fukui matrix and may be resolved in atom and bond contributions. The extra information contained in the atom and bond resolution of the Fukui matrices and functions is highlighted. The effect of the choice of weight function arising from the Hirshfeld-I approach to obtain atom- and bond-condensed Fukui functions is studied. A comparison of the results with those generated by using the Mulliken atoms-in-molecule approach shows low correlation between the two partitioning schemes. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A benchmarking method to measure dietary absorption efficiency of chemicals by fish.

PubMed

Xiao, Ruiyang; Adolfsson-Erici, Margaretha; Åkerman, Gun; McLachlan, Michael S; MacLeod, Matthew

2013-12-01

Understanding the dietary absorption efficiency of chemicals in the gastrointestinal tract of fish is important from both a scientific and a regulatory point of view. However, reported fish absorption efficiencies for well-studied chemicals are highly variable. In the present study, the authors developed and exploited an internal chemical benchmarking method that has the potential to reduce uncertainty and variability and, thus, to improve the precision of measurements of fish absorption efficiency. The authors applied the benchmarking method to measure the gross absorption efficiency for 15 chemicals with a wide range of physicochemical properties and structures. They selected 2,2',5,6'-tetrachlorobiphenyl (PCB53) and decabromodiphenyl ethane as absorbable and nonabsorbable benchmarks, respectively. Quantities of chemicals determined in fish were benchmarked to the fraction of PCB53 recovered in fish, and quantities of chemicals determined in feces were benchmarked to the fraction of decabromodiphenyl ethane recovered in feces. The performance of the benchmarking procedure was evaluated based on the recovery of the test chemicals and precision of absorption efficiency from repeated tests. Benchmarking did not improve the precision of the measurements; after benchmarking, however, the median recovery for 15 chemicals was 106%, and variability of recoveries was reduced compared with before benchmarking, suggesting that benchmarking could account for incomplete extraction of chemical in fish and incomplete collection of feces from different tests. © 2013 SETAC.

Benchmarks for Psychotherapy Efficacy in Adult Major Depression

ERIC Educational Resources Information Center

Minami, Takuya; Wampold, Bruce E.; Serlin, Ronald C.; Kircher, John C.; Brown, George S.

2007-01-01

This study estimates pretreatment-posttreatment effect size benchmarks for the treatment of major depression in adults that may be useful in evaluating psychotherapy effectiveness in clinical practice. Treatment efficacy benchmarks for major depression were derived for 3 different types of outcome measures: the Hamilton Rating Scale for Depression…

[Benchmarking and other functions of ROM: back to basics].

PubMed

Barendregt, M

2015-01-01

Since 2011 outcome data in the Dutch mental health care have been collected on a national scale. This has led to confusion about the position of benchmarking in the system known as routine outcome monitoring (rom). To provide insight into the various objectives and uses of aggregated outcome data. A qualitative review was performed and the findings were analysed. Benchmarking is a strategy for finding best practices and for improving efficacy and it belongs to the domain of quality management. Benchmarking involves comparing outcome data by means of instrumentation and is relatively tolerant with regard to the validity of the data. Although benchmarking is a function of rom, it must be differentiated form other functions from rom. Clinical management, public accountability, research, payment for performance and information for patients are all functions of rom which require different ways of data feedback and which make different demands on the validity of the underlying data. Benchmarking is often wrongly regarded as being simply a synonym for 'comparing institutions'. It is, however, a method which includes many more factors; it can be used to improve quality and has a more flexible approach to the validity of outcome data and is less concerned than other rom functions about funding and the amount of information given to patients. Benchmarking can make good use of currently available outcome data.

Benchmarking with the BLASST Sessional Staff Standards Framework

ERIC Educational Resources Information Center

Luzia, Karina; Harvey, Marina; Parker, Nicola; McCormack, Coralie; Brown, Natalie R.

2013-01-01

Benchmarking as a type of knowledge-sharing around good practice within and between institutions is increasingly common in the higher education sector. More recently, benchmarking as a process that can contribute to quality enhancement has been deployed across numerous institutions with a view to systematising frameworks to assure and enhance the…

Evanescent Wave Atomic Mirror

NASA Astrophysics Data System (ADS)

Ghezali, S.; Taleb, A.

2008-09-01

A research project at the "Laboratoire d'électronique quantique" consists in a theoretical study of the reflection and diffraction phenomena via an atomic mirror. This poster presents the principle of an atomic mirror. Many groups in the world have constructed this type of atom optics experiments such as in Paris-Orsay-Villetaneuse (France), Stanford-Gaithersburg (USA), Munich-Heidelberg (Germany), etc. A laser beam goes into a prism with an incidence bigger than the critical incidence. It undergoes a total reflection on the plane face of the prism and then exits. The transmitted resulting wave out of the prism is evanescent and repulsive as the frequency detuning of the laser beam compared to the atomic transition δ = ωL-ω0 is positive. The cold atomic sample interacts with this evanescent wave and undergoes one or more elastic bounces by passing into backward points in its trajectory because the atoms' kinetic energy (of the order of the μeV) is less than the maximum of the dipolar potential barrier ℏΩ2/Δ where Ω is the Rabi frequency [1]. In fact, the atoms are cooled and captured in a magneto-optical trap placed at a distance of the order of the cm above the prism surface. The dipolar potential with which interact the slow atoms is obtained for a two level atom in a case of a dipolar electric transition (D2 Rubidium transition at a wavelength of 780nm delivered by a Titane-Saphir laser between a fundamental state Jf = l/2 and an excited state Je = 3/2). This potential is corrected by an attractive Van der Waals term which varies as 1/z3 in the Lennard-Jones approximation (typical atomic distance of the order of λ0/2π where λ0 is the laser wavelength) and in 1/z4 if the distance between the atom and its image in the dielectric is big in front of λ0/2π. This last case is obtained in a quantum electrodynamic calculation by taking into account an orthornormal base [2]. We'll examine the role of spontaneous emission for which the rate is inversely

Observing heliospheric neutral atoms at 1 AU

NASA Astrophysics Data System (ADS)

Heerikhuisen, Jacob; Pogorelov, Nikolai; Florinski, Vladimir; Zank, Gary

2006-09-01

Although in situ observations of distant heliospheric plasma by the Voyagers has proven to be extremely enlightening, such point observations need to be complemented with global measurements taken remotely to obtain a complete picture of the heliosphere and local interstellar environment. Neutral atoms, with their contempt for magnetic fields, provide useful probes of the plasma that generated them. However, there will be a number of ambiguities in neutral atom readings that require a deeper understanding of the plasma processes generating neutral atoms, as well as the loss mechanisms on their flight to the observation point. We introduce a procedure for generating all-sky maps of energetic H-atoms, calculated directly in our Monte-Carlo neutral atom code. Results obtained for a self-consistent axisymmetric MHD-Boltzmann calculation, as well as several non-selfconsistent 3D sky maps, will be presented.

Comparison of Origin 2000 and Origin 3000 Using NAS Parallel Benchmarks

NASA Technical Reports Server (NTRS)

Turney, Raymond D.

2001-01-01

This report describes results of benchmark tests on the Origin 3000 system currently being installed at the NASA Ames National Advanced Supercomputing facility. This machine will ultimately contain 1024 R14K processors. The first part of the system, installed in November, 2000 and named mendel, is an Origin 3000 with 128 R12K processors. For comparison purposes, the tests were also run on lomax, an Origin 2000 with R12K processors. The BT, LU, and SP application benchmarks in the NAS Parallel Benchmark Suite and the kernel benchmark FT were chosen to determine system performance and measure the impact of changes on the machine as it evolves. Having been written to measure performance on Computational Fluid Dynamics applications, these benchmarks are assumed appropriate to represent the NAS workload. Since the NAS runs both message passing (MPI) and shared-memory, compiler directive type codes, both MPI and OpenMP versions of the benchmarks were used. The MPI versions used were the latest official release of the NAS Parallel Benchmarks, version 2.3. The OpenMP versiqns used were PBN3b2, a beta version that is in the process of being released. NPB 2.3 and PBN 3b2 are technically different benchmarks, and NPB results are not directly comparable to PBN results.

OWL2 benchmarking for the evaluation of knowledge based systems.

PubMed

Khan, Sher Afgun; Qadir, Muhammad Abdul; Abbas, Muhammad Azeem; Afzal, Muhammad Tanvir

2017-01-01

OWL2 semantics are becoming increasingly popular for the real domain applications like Gene engineering and health MIS. The present work identifies the research gap that negligible attention has been paid to the performance evaluation of Knowledge Base Systems (KBS) using OWL2 semantics. To fulfil this identified research gap, an OWL2 benchmark for the evaluation of KBS is proposed. The proposed benchmark addresses the foundational blocks of an ontology benchmark i.e. data schema, workload and performance metrics. The proposed benchmark is tested on memory based, file based, relational database and graph based KBS for performance and scalability measures. The results show that the proposed benchmark is able to evaluate the behaviour of different state of the art KBS on OWL2 semantics. On the basis of the results, the end users (i.e. domain expert) would be able to select a suitable KBS appropriate for his domain.

Benchmarking and beyond. Information trends in home care.

PubMed

Twiss, Amanda; Rooney, Heather; Lang, Christine

2002-11-01

With today's benchmarking concepts and tools, agencies have the unprecedented opportunity to use information as a strategic advantage. Because agencies are demanding more and better information, benchmark functionality has grown increasingly sophisticated. Agencies now require a new type of analysis, focused on high-level executive summaries while reducing the current "data overload."

Atomic characterization of Si nanoclusters embedded in SiO2 by atom probe tomography

PubMed Central

2011-01-01

Silicon nanoclusters are of prime interest for new generation of optoelectronic and microelectronics components. Physical properties (light emission, carrier storage...) of systems using such nanoclusters are strongly dependent on nanostructural characteristics. These characteristics (size, composition, distribution, and interface nature) are until now obtained using conventional high-resolution analytic methods, such as high-resolution transmission electron microscopy, EFTEM, or EELS. In this article, a complementary technique, the atom probe tomography, was used for studying a multilayer (ML) system containing silicon clusters. Such a technique and its analysis give information on the structure at the atomic level and allow obtaining complementary information with respect to other techniques. A description of the different steps for such analysis: sample preparation, atom probe analysis, and data treatment are detailed. An atomic scale description of the Si nanoclusters/SiO2 ML will be fully described. This system is composed of 3.8-nm-thick SiO layers and 4-nm-thick SiO2 layers annealed 1 h at 900°C. PMID:21711666

Magnified pseudo-elemental map of atomic column obtained by Moiré method in scanning transmission electron microscopy.

PubMed

Kondo, Yukihito; Okunishi, Eiji

2014-10-01

Moiré method in scanning transmission electron microscopy allows observing a magnified two-dimensional atomic column elemental map of a higher pixel resolution with a lower electron dose unlike conventional atomic column mapping. The magnification of the map is determined by the ratio between the pixel size and the lattice spacing. With proper ratios for the x and y directions, we could observe magnified elemental maps, homothetic to the atomic arrangement in the sample of SrTiO3 [0 0 1]. The map showed peaks at all expected oxygen sites in SrTiO3 [0 0 1]. © The Author 2014. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Benchmarking strategies for measuring the quality of healthcare: problems and prospects.

PubMed

Lovaglio, Pietro Giorgio

2012-01-01

Over the last few years, increasing attention has been directed toward the problems inherent to measuring the quality of healthcare and implementing benchmarking strategies. Besides offering accreditation and certification processes, recent approaches measure the performance of healthcare institutions in order to evaluate their effectiveness, defined as the capacity to provide treatment that modifies and improves the patient's state of health. This paper, dealing with hospital effectiveness, focuses on research methods for effectiveness analyses within a strategy comparing different healthcare institutions. The paper, after having introduced readers to the principle debates on benchmarking strategies, which depend on the perspective and type of indicators used, focuses on the methodological problems related to performing consistent benchmarking analyses. Particularly, statistical methods suitable for controlling case-mix, analyzing aggregate data, rare events, and continuous outcomes measured with error are examined. Specific challenges of benchmarking strategies, such as the risk of risk adjustment (case-mix fallacy, underreporting, risk of comparing noncomparable hospitals), selection bias, and possible strategies for the development of consistent benchmarking analyses, are discussed. Finally, to demonstrate the feasibility of the illustrated benchmarking strategies, an application focused on determining regional benchmarks for patient satisfaction (using 2009 Lombardy Region Patient Satisfaction Questionnaire) is proposed.

Benchmark Dataset for Whole Genome Sequence Compression.

PubMed

C L, Biji; S Nair, Achuthsankar

2017-01-01

The research in DNA data compression lacks a standard dataset to test out compression tools specific to DNA. This paper argues that the current state of achievement in DNA compression is unable to be benchmarked in the absence of such scientifically compiled whole genome sequence dataset and proposes a benchmark dataset using multistage sampling procedure. Considering the genome sequence of organisms available in the National Centre for Biotechnology and Information (NCBI) as the universe, the proposed dataset selects 1,105 prokaryotes, 200 plasmids, 164 viruses, and 65 eukaryotes. This paper reports the results of using three established tools on the newly compiled dataset and show that their strength and weakness are evident only with a comparison based on the scientifically compiled benchmark dataset. The sample dataset and the respective links are available @ https://sourceforge.net/projects/benchmarkdnacompressiondataset/.

Scalable randomized benchmarking of non-Clifford gates

NASA Astrophysics Data System (ADS)

Cross, Andrew; Magesan, Easwar; Bishop, Lev; Smolin, John; Gambetta, Jay

Randomized benchmarking is a widely used experimental technique to characterize the average error of quantum operations. Benchmarking procedures that scale to enable characterization of n-qubit circuits rely on efficient procedures for manipulating those circuits and, as such, have been limited to subgroups of the Clifford group. However, universal quantum computers require additional, non-Clifford gates to approximate arbitrary unitary transformations. We define a scalable randomized benchmarking procedure over n-qubit unitary matrices that correspond to protected non-Clifford gates for a class of stabilizer codes. We present efficient methods for representing and composing group elements, sampling them uniformly, and synthesizing corresponding poly (n) -sized circuits. The procedure provides experimental access to two independent parameters that together characterize the average gate fidelity of a group element. We acknowledge support from ARO under Contract W911NF-14-1-0124.

Galileo probe forebody thermal protection - Benchmark heating environment calculations

NASA Technical Reports Server (NTRS)

Balakrishnan, A.; Nicolet, W. E.

1981-01-01

Solutions are presented for the aerothermal heating environment for the forebody heatshield of candidate Galileo probe. Entry into both the nominal and cool-heavy model atmospheres were considered. Solutions were obtained for the candidate heavy probe with a weight of 310 kg and a lighter probe with a weight of 290 kg. In the flowfield analysis, a finite difference procedure was employed to obtain benchmark predictions of pressure, radiative and convective heating rates, and the steady-state wall blowing rates. Calculated heating rates for entry into the cool-heavy model atmosphere were about 60 percent higher than those predicted for the entry into the nominal atmosphere. The total mass lost for entry into the cool-heavy model atmosphere was about 146 kg and the mass lost for entry into the nominal model atmosphere was about 101 kg.

Pulsed source of energetic atomic oxygen

NASA Technical Reports Server (NTRS)

Caledonia, George E.; Krech, Robert H.

1987-01-01

A pulsed high flux source of nearly monoenergetic atomic oxygen was designed, built, and successfully demonstrated. Molecular oxygen at several atmospheres pressure is introduced into an evacuated supersonic expansion nozzle through a pulsed molecular beam valve. An 18 J pulsed CO2 TEA laser is focused to intensities greater than 10(9) W/sq cm in the nozzle throat to generate a laser-induced breakdown. The resulting plasma is heated in excess of 20,000 K by a laser supported detonation wave, and then rapidly expands and cools. Nozzle geometry confines the expansion to provide rapid electron-ion recombination into atomic oxygen. Average O atom beam velocities from 5 to 13 km/s were measured at estimated fluxes to 10(18) atoms per pulse. Preliminary materials testing has produced the same surface oxygen enrichment in polyethylene samples as obtained on the STS-8 mission. Scanning electron microscope examinations of irradiated polymer surfaces reveal an erosion morphology similar to that obtained in low Earth orbit, with an estimated mass removal rate of approx. 10(-24) cu cm/atom. The characteristics of the O atom source and the results of some preliminary materials testing studies are reviewed.

Benchmarking: A Method for Continuous Quality Improvement in Health

PubMed Central

Ettorchi-Tardy, Amina; Levif, Marie; Michel, Philippe

2012-01-01

Benchmarking, a management approach for implementing best practices at best cost, is a recent concept in the healthcare system. The objectives of this paper are to better understand the concept and its evolution in the healthcare sector, to propose an operational definition, and to describe some French and international experiences of benchmarking in the healthcare sector. To this end, we reviewed the literature on this approach's emergence in the industrial sector, its evolution, its fields of application and examples of how it has been used in the healthcare sector. Benchmarking is often thought to consist simply of comparing indicators and is not perceived in its entirety, that is, as a tool based on voluntary and active collaboration among several organizations to create a spirit of competition and to apply best practices. The key feature of benchmarking is its integration within a comprehensive and participatory policy of continuous quality improvement (CQI). Conditions for successful benchmarking focus essentially on careful preparation of the process, monitoring of the relevant indicators, staff involvement and inter-organizational visits. Compared to methods previously implemented in France (CQI and collaborative projects), benchmarking has specific features that set it apart as a healthcare innovation. This is especially true for healthcare or medical–social organizations, as the principle of inter-organizational visiting is not part of their culture. Thus, this approach will need to be assessed for feasibility and acceptability before it is more widely promoted. PMID:23634166

Benchmarking: a method for continuous quality improvement in health.

PubMed

Ettorchi-Tardy, Amina; Levif, Marie; Michel, Philippe

2012-05-01

Benchmarking, a management approach for implementing best practices at best cost, is a recent concept in the healthcare system. The objectives of this paper are to better understand the concept and its evolution in the healthcare sector, to propose an operational definition, and to describe some French and international experiences of benchmarking in the healthcare sector. To this end, we reviewed the literature on this approach's emergence in the industrial sector, its evolution, its fields of application and examples of how it has been used in the healthcare sector. Benchmarking is often thought to consist simply of comparing indicators and is not perceived in its entirety, that is, as a tool based on voluntary and active collaboration among several organizations to create a spirit of competition and to apply best practices. The key feature of benchmarking is its integration within a comprehensive and participatory policy of continuous quality improvement (CQI). Conditions for successful benchmarking focus essentially on careful preparation of the process, monitoring of the relevant indicators, staff involvement and inter-organizational visits. Compared to methods previously implemented in France (CQI and collaborative projects), benchmarking has specific features that set it apart as a healthcare innovation. This is especially true for healthcare or medical-social organizations, as the principle of inter-organizational visiting is not part of their culture. Thus, this approach will need to be assessed for feasibility and acceptability before it is more widely promoted.

Implementation of NAS Parallel Benchmarks in Java

NASA Technical Reports Server (NTRS)

Frumkin, Michael; Schultz, Matthew; Jin, Hao-Qiang; Yan, Jerry

2000-01-01

A number of features make Java an attractive but a debatable choice for High Performance Computing (HPC). In order to gauge the applicability of Java to the Computational Fluid Dynamics (CFD) we have implemented NAS Parallel Benchmarks in Java. The performance and scalability of the benchmarks point out the areas where improvement in Java compiler technology and in Java thread implementation would move Java closer to Fortran in the competition for CFD applications.

Data Race Benchmark Collection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liao, Chunhua; Lin, Pei-Hung; Asplund, Joshua

2017-03-21

This project is a benchmark suite of Open-MP parallel codes that have been checked for data races. The programs are marked to show which do and do not have races. This allows them to be leveraged while testing and developing race detection tools.

The Medical Library Association Benchmarking Network: development and implementation.

PubMed

Dudden, Rosalind Farnam; Corcoran, Kate; Kaplan, Janice; Magouirk, Jeff; Rand, Debra C; Smith, Bernie Todd

2006-04-01

This article explores the development and implementation of the Medical Library Association (MLA) Benchmarking Network from the initial idea and test survey, to the implementation of a national survey in 2002, to the establishment of a continuing program in 2004. Started as a program for hospital libraries, it has expanded to include other nonacademic health sciences libraries. The activities and timelines of MLA's Benchmarking Network task forces and editorial board from 1998 to 2004 are described. The Benchmarking Network task forces successfully developed an extensive questionnaire with parameters of size and measures of library activity and published a report of the data collected by September 2002. The data were available to all MLA members in the form of aggregate tables. Utilization of Web-based technologies proved feasible for data intake and interactive display. A companion article analyzes and presents some of the data. MLA has continued to develop the Benchmarking Network with the completion of a second survey in 2004. The Benchmarking Network has provided many small libraries with comparative data to present to their administrators. It is a challenge for the future to convince all MLA members to participate in this valuable program.

Atomic clusters and atomic surfaces in icosahedral quasicrystals.

PubMed

Quiquandon, Marianne; Portier, Richard; Gratias, Denis

2014-05-01

This paper presents the basic tools commonly used to describe the atomic structures of quasicrystals with a specific focus on the icosahedral phases. After a brief recall of the main properties of quasiperiodic objects, two simple physical rules are discussed that lead one to eventually obtain a surprisingly small number of atomic structures as ideal quasiperiodic models for real quasicrystals. This is due to the fact that the atomic surfaces (ASs) used to describe all known icosahedral phases are located on high-symmetry special points in six-dimensional space. The first rule is maximizing the density using simple polyhedral ASs that leads to two possible sets of ASs according to the value of the six-dimensional lattice parameter A between 0.63 and 0.79 nm. The second rule is maximizing the number of complete orbits of high symmetry to construct as large as possible atomic clusters similar to those observed in complex intermetallic structures and approximant phases. The practical use of these two rules together is demonstrated on two typical examples of icosahedral phases, i-AlMnSi and i-CdRE (RE = Gd, Ho, Tm).

Site-selective substitutional doping with atomic precision on stepped Al (111) surface by single-atom manipulation

PubMed Central

2014-01-01

In fabrication of nano- and quantum devices, it is sometimes critical to position individual dopants at certain sites precisely to obtain the specific or enhanced functionalities. With first-principles simulations, we propose a method for substitutional doping of individual atom at a certain position on a stepped metal surface by single-atom manipulation. A selected atom at the step of Al (111) surface could be extracted vertically with an Al trimer-apex tip, and then the dopant atom will be positioned to this site. The details of the entire process including potential energy curves are given, which suggests the reliability of the proposed single-atom doping method. PMID:24899871

Site-selective substitutional doping with atomic precision on stepped Al (111) surface by single-atom manipulation.

PubMed

Chen, Chang; Zhang, Jinhu; Dong, Guofeng; Shao, Hezhu; Ning, Bo-Yuan; Zhao, Li; Ning, Xi-Jing; Zhuang, Jun

2014-01-01

In fabrication of nano- and quantum devices, it is sometimes critical to position individual dopants at certain sites precisely to obtain the specific or enhanced functionalities. With first-principles simulations, we propose a method for substitutional doping of individual atom at a certain position on a stepped metal surface by single-atom manipulation. A selected atom at the step of Al (111) surface could be extracted vertically with an Al trimer-apex tip, and then the dopant atom will be positioned to this site. The details of the entire process including potential energy curves are given, which suggests the reliability of the proposed single-atom doping method.

Implementation and verification of global optimization benchmark problems

NASA Astrophysics Data System (ADS)

Posypkin, Mikhail; Usov, Alexander

2017-12-01

The paper considers the implementation and verification of a test suite containing 150 benchmarks for global deterministic box-constrained optimization. A C++ library for describing standard mathematical expressions was developed for this purpose. The library automate the process of generating the value of a function and its' gradient at a given point and the interval estimates of a function and its' gradient on a given box using a single description. Based on this functionality, we have developed a collection of tests for an automatic verification of the proposed benchmarks. The verification has shown that literary sources contain mistakes in the benchmarks description. The library and the test suite are available for download and can be used freely.

Memory-Intensive Benchmarks: IRAM vs. Cache-Based Machines

NASA Technical Reports Server (NTRS)

Biswas, Rupak; Gaeke, Brian R.; Husbands, Parry; Li, Xiaoye S.; Oliker, Leonid; Yelick, Katherine A.; Biegel, Bryan (Technical Monitor)

2002-01-01

The increasing gap between processor and memory performance has lead to new architectural models for memory-intensive applications. In this paper, we explore the performance of a set of memory-intensive benchmarks and use them to compare the performance of conventional cache-based microprocessors to a mixed logic and DRAM processor called VIRAM. The benchmarks are based on problem statements, rather than specific implementations, and in each case we explore the fundamental hardware requirements of the problem, as well as alternative algorithms and data structures that can help expose fine-grained parallelism or simplify memory access patterns. The benchmarks are characterized by their memory access patterns, their basic control structures, and the ratio of computation to memory operation.

Two-dimensional free-surface flow under gravity: A new benchmark case for SPH method

NASA Astrophysics Data System (ADS)

Wu, J. Z.; Fang, L.

2018-02-01

Currently there are few free-surface benchmark cases with analytical results for the Smoothed Particle Hydrodynamics (SPH) simulation. In the present contribution we introduce a two-dimensional free-surface flow under gravity, and obtain an analytical expression on the surface height difference and a theoretical estimation on the surface fractal dimension. They are preliminarily validated and supported by SPH calculations.

New NAS Parallel Benchmarks Results

NASA Technical Reports Server (NTRS)

Yarrow, Maurice; Saphir, William; VanderWijngaart, Rob; Woo, Alex; Kutler, Paul (Technical Monitor)

1997-01-01

NPB2 (NAS (NASA Advanced Supercomputing) Parallel Benchmarks 2) is an implementation, based on Fortran and the MPI (message passing interface) message passing standard, of the original NAS Parallel Benchmark specifications. NPB2 programs are run with little or no tuning, in contrast to NPB vendor implementations, which are highly optimized for specific architectures. NPB2 results complement, rather than replace, NPB results. Because they have not been optimized by vendors, NPB2 implementations approximate the performance a typical user can expect for a portable parallel program on distributed memory parallel computers. Together these results provide an insightful comparison of the real-world performance of high-performance computers. New NPB2 features: New implementation (CG), new workstation class problem sizes, new serial sample versions, more performance statistics.

C6 Coefficients and Dipole Polarizabilities for All Atoms and Many Ions in Rows 1-6 of the Periodic Table.

PubMed

Gould, Tim; Bučko, Tomáš

2016-08-09

Using time-dependent density functional theory (TDDFT) with exchange kernels, we calculate and test imaginary frequency-dependent dipole polarizabilities for all atoms and many ions in rows 1-6 of the periodic table. These are then integrated over frequency to produce C6 coefficients. Results are presented under different models: straight TDDFT calculations using two different kernels; "benchmark" TDDFT calculations corrected by more accurate quantum chemical and experimental data; and "benchmark" TDDFT with frozen orbital anions. Parametrizations are presented for 411+ atoms and ions, allowing results to be easily used by other researchers. A curious relationship, C6,XY ∝ [αX(0)αY(0)](0.73), is found between C6 coefficients and static polarizabilities α(0). The relationship C6,XY = 2C6,XC6,Y/[(αX/αY)C6,Y + (αY/αX)C6,X] is tested and found to work well (<5% errors) in ∼80% of the cases, but can break down badly (>30% errors) in a small fraction of cases.

Development and application of freshwater sediment-toxicity benchmarks for currently used pesticides

USGS Publications Warehouse

Nowell, Lisa H.; Norman, Julia E.; Ingersoll, Christopher G.; Moran, Patrick W.

2016-01-01

Sediment-toxicity benchmarks are needed to interpret the biological significance of currently used pesticides detected in whole sediments. Two types of freshwater sediment benchmarks for pesticides were developed using spiked-sediment bioassay (SSB) data from the literature. These benchmarks can be used to interpret sediment-toxicity data or to assess the potential toxicity of pesticides in whole sediment. The Likely Effect Benchmark (LEB) defines a pesticide concentration in whole sediment above which there is a high probability of adverse effects on benthic invertebrates, and the Threshold Effect Benchmark (TEB) defines a concentration below which adverse effects are unlikely. For compounds without available SSBs, benchmarks were estimated using equilibrium partitioning (EqP). When a sediment sample contains a pesticide mixture, benchmark quotients can be summed for all detected pesticides to produce an indicator of potential toxicity for that mixture. Benchmarks were developed for 48 pesticide compounds using SSB data and 81 compounds using the EqP approach. In an example application, data for pesticides measured in sediment from 197 streams across the United States were evaluated using these benchmarks, and compared to measured toxicity from whole-sediment toxicity tests conducted with the amphipod Hyalella azteca (28-d exposures) and the midge Chironomus dilutus (10-d exposures). Amphipod survival, weight, and biomass were significantly and inversely related to summed benchmark quotients, whereas midge survival, weight, and biomass showed no relationship to benchmarks. Samples with LEB exceedances were rare (n = 3), but all were toxic to amphipods (i.e., significantly different from control). Significant toxicity to amphipods was observed for 72% of samples exceeding one or more TEBs, compared to 18% of samples below all TEBs. Factors affecting toxicity below TEBs may include the presence of contaminants other than pesticides, physical

On-line atomic data access

NASA Astrophysics Data System (ADS)

Schultz, David R.; Nash, Jeffrey K.

1996-07-01

The need for atomic data is one which continues to expand in a wide variety of applications including fusion energy, astrophysics, laser-produced plasma research, and plasma processing. Modern computer database and communications technology enables this data to be placed on-line and obtained by users over the INTERNET. Presented here is a summary of the observations and conclusions regarding such on-line atomic data access derived from a forum held at the Tenth APS Topical Conference on Atomic Processes in Plasmas.

Multipolar electrostatics for proteins: atom-atom electrostatic energies in crambin.

PubMed

Yuan, Yongna; Mills, Matthew J L; Popelier, Paul L A

2014-02-15

Accurate electrostatics necessitates the use of multipole moments centered on nuclei or extra point charges centered away from the nuclei. Here, we follow the former alternative and investigate the convergence behavior of atom-atom electrostatic interactions in the pilot protein crambin. Amino acids are cut out from a Protein Data Bank structure of crambin, as single amino acids, di, or tripeptides, and are then capped with a peptide bond at each side. The atoms in the amino acids are defined through Quantum Chemical Topology (QCT) as finite volume electron density fragments. Atom-atom electrostatic energies are computed by means of a multipole expansion with regular spherical harmonics, up to a total interaction rank of L = ℓA+ ℓB + 1 = 10. The minimum internuclear distance in the convergent region of all the 15 possible types of atom-atom interactions in crambin that were calculated based on single amino acids are close to the values calculated from di and tripeptides. Values obtained at B3LYP/aug-cc-pVTZ and MP2/aug-cc-pVTZ levels are only slightly larger than those calculated at HF/6-31G(d,p) level. This convergence behavior is transferable to the well-known amyloid beta polypeptide Aβ1-42. Moreover, for a selected central atom, the influence of its neighbors on its multipole moments is investigated, and how far away this influence can be ignored is also determined. Finally, the convergence behavior of AMBER becomes closer to that of QCT with increasing internuclear distance. Copyright © 2013 Wiley Periodicals, Inc.

The performance and limitations of FPGA-based digital servos for atomic, molecular, and optical physics experiments

NASA Astrophysics Data System (ADS)

Yu, Shi Jing; Fajeau, Emma; Liu, Lin Qiao; Jones, David J.; Madison, Kirk W.

2018-02-01

In this work, we address the advantages, limitations, and technical subtleties of employing field programmable gate array (FPGA)-based digital servos for high-bandwidth feedback control of lasers in atomic, molecular, and optical physics experiments. Specifically, we provide the results of benchmark performance tests in experimental setups including noise, bandwidth, and dynamic range for two digital servos built with low and mid-range priced FPGA development platforms. The digital servo results are compared to results obtained from a commercially available state-of-the-art analog servo using the same plant for control (intensity stabilization). The digital servos have feedback bandwidths of 2.5 MHz, limited by the total signal latency, and we demonstrate improvements beyond the transfer function offered by the analog servo including a three-pole filter and a two-pole filter with phase compensation to suppress resonances. We also discuss limitations of our FPGA-servo implementation and general considerations when designing and using digital servos.

The performance and limitations of FPGA-based digital servos for atomic, molecular, and optical physics experiments.

PubMed

Yu, Shi Jing; Fajeau, Emma; Liu, Lin Qiao; Jones, David J; Madison, Kirk W

2018-02-01

In this work, we address the advantages, limitations, and technical subtleties of employing field programmable gate array (FPGA)-based digital servos for high-bandwidth feedback control of lasers in atomic, molecular, and optical physics experiments. Specifically, we provide the results of benchmark performance tests in experimental setups including noise, bandwidth, and dynamic range for two digital servos built with low and mid-range priced FPGA development platforms. The digital servo results are compared to results obtained from a commercially available state-of-the-art analog servo using the same plant for control (intensity stabilization). The digital servos have feedback bandwidths of 2.5 MHz, limited by the total signal latency, and we demonstrate improvements beyond the transfer function offered by the analog servo including a three-pole filter and a two-pole filter with phase compensation to suppress resonances. We also discuss limitations of our FPGA-servo implementation and general considerations when designing and using digital servos.

Benchmarking in Education: Tech Prep, a Case in Point. IEE Brief Number 8.

ERIC Educational Resources Information Center

Inger, Morton

Benchmarking is a process by which organizations compare their practices, processes, and outcomes to standards of excellence in a systematic way. The benchmarking process entails the following essential steps: determining what to benchmark and establishing internal baseline data; identifying the benchmark; determining how that standard has been…

Polymerization of a divalent/tetravalent metal-storing atom-mimicking dendrimer.

PubMed

Albrecht, Ken; Hirabayashi, Yuki; Otake, Masaya; Mendori, Shin; Tobari, Yuta; Azuma, Yasuo; Majima, Yutaka; Yamamoto, Kimihisa

2016-12-01

The phenylazomethine dendrimer (DPA) has a layer-by-layer electron density gradient that is an analog of the Bohr atom (atom mimicry). In combination with electron pair mimicry, the polymerization of this atom-mimicking dendrimer was achieved. The valency of the mimicked atom was controlled by changing the chemical structure of the dendrimer. By mimicking a divalent atom, a one-dimensional (1D) polymer was obtained, and by using a planar tetravalent atom mimic, a 2D polymer was obtained. These poly(dendrimer) polymers could store Lewis acids (SnCl 2 ) in their unoccupied orbitals, thus indicating that these poly(dendrimer) polymers consist of a series of nanocontainers.

Benchmarking Strategies for Measuring the Quality of Healthcare: Problems and Prospects

PubMed Central

Lovaglio, Pietro Giorgio

2012-01-01

Over the last few years, increasing attention has been directed toward the problems inherent to measuring the quality of healthcare and implementing benchmarking strategies. Besides offering accreditation and certification processes, recent approaches measure the performance of healthcare institutions in order to evaluate their effectiveness, defined as the capacity to provide treatment that modifies and improves the patient's state of health. This paper, dealing with hospital effectiveness, focuses on research methods for effectiveness analyses within a strategy comparing different healthcare institutions. The paper, after having introduced readers to the principle debates on benchmarking strategies, which depend on the perspective and type of indicators used, focuses on the methodological problems related to performing consistent benchmarking analyses. Particularly, statistical methods suitable for controlling case-mix, analyzing aggregate data, rare events, and continuous outcomes measured with error are examined. Specific challenges of benchmarking strategies, such as the risk of risk adjustment (case-mix fallacy, underreporting, risk of comparing noncomparable hospitals), selection bias, and possible strategies for the development of consistent benchmarking analyses, are discussed. Finally, to demonstrate the feasibility of the illustrated benchmarking strategies, an application focused on determining regional benchmarks for patient satisfaction (using 2009 Lombardy Region Patient Satisfaction Questionnaire) is proposed. PMID:22666140

MIPS bacterial genomes functional annotation benchmark dataset.

PubMed

Tetko, Igor V; Brauner, Barbara; Dunger-Kaltenbach, Irmtraud; Frishman, Goar; Montrone, Corinna; Fobo, Gisela; Ruepp, Andreas; Antonov, Alexey V; Surmeli, Dimitrij; Mewes, Hans-Wernen

2005-05-15

Any development of new methods for automatic functional annotation of proteins according to their sequences requires high-quality data (as benchmark) as well as tedious preparatory work to generate sequence parameters required as input data for the machine learning methods. Different program settings and incompatible protocols make a comparison of the analyzed methods difficult. The MIPS Bacterial Functional Annotation Benchmark dataset (MIPS-BFAB) is a new, high-quality resource comprising four bacterial genomes manually annotated according to the MIPS functional catalogue (FunCat). These resources include precalculated sequence parameters, such as sequence similarity scores, InterPro domain composition and other parameters that could be used to develop and benchmark methods for functional annotation of bacterial protein sequences. These data are provided in XML format and can be used by scientists who are not necessarily experts in genome annotation. BFAB is available at http://mips.gsf.de/proj/bfab

42 CFR 440.335 - Benchmark-equivalent health benefits coverage.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Aggregate actuarial value. Benchmark-equivalent coverage is health benefits coverage that has an aggregate... planning services and supplies and other appropriate preventive services, as designated by the Secretary... State for purposes of comparison in establishing the aggregate actuarial value of the benchmark...

Benchmarking in pathology: development of a benchmarking complexity unit and associated key performance indicators.

PubMed

Neil, Amanda; Pfeffer, Sally; Burnett, Leslie

2013-01-01

This paper details the development of a new type of pathology laboratory productivity unit, the benchmarking complexity unit (BCU). The BCU provides a comparative index of laboratory efficiency, regardless of test mix. It also enables estimation of a measure of how much complex pathology a laboratory performs, and the identification of peer organisations for the purposes of comparison and benchmarking. The BCU is based on the theory that wage rates reflect productivity at the margin. A weighting factor for the ratio of medical to technical staff time was dynamically calculated based on actual participant site data. Given this weighting, a complexity value for each test, at each site, was calculated. The median complexity value (number of BCUs) for that test across all participating sites was taken as its complexity value for the Benchmarking in Pathology Program. The BCU allowed implementation of an unbiased comparison unit and test listing that was found to be a robust indicator of the relative complexity for each test. Employing the BCU data, a number of Key Performance Indicators (KPIs) were developed, including three that address comparative organisational complexity, analytical depth and performance efficiency, respectively. Peer groups were also established using the BCU combined with simple organisational and environmental metrics. The BCU has enabled productivity statistics to be compared between organisations. The BCU corrects for differences in test mix and workload complexity of different organisations and also allows for objective stratification into peer groups.

Test One to Test Many: A Unified Approach to Quantum Benchmarks

NASA Astrophysics Data System (ADS)

Bai, Ge; Chiribella, Giulio

2018-04-01

Quantum benchmarks are routinely used to validate the experimental demonstration of quantum information protocols. Many relevant protocols, however, involve an infinite set of input states, of which only a finite subset can be used to test the quality of the implementation. This is a problem, because the benchmark for the finitely many states used in the test can be higher than the original benchmark calculated for infinitely many states. This situation arises in the teleportation and storage of coherent states, for which the benchmark of 50% fidelity is commonly used in experiments, although finite sets of coherent states normally lead to higher benchmarks. Here, we show that the average fidelity over all coherent states can be indirectly probed with a single setup, requiring only two-mode squeezing, a 50-50 beam splitter, and homodyne detection. Our setup enables a rigorous experimental validation of quantum teleportation, storage, amplification, attenuation, and purification of noisy coherent states. More generally, we prove that every quantum benchmark can be tested by preparing a single entangled state and measuring a single observable.

Scanning Quantum Cryogenic Atom Microscope

NASA Astrophysics Data System (ADS)

Yang, Fan; Kollár, Alicia J.; Taylor, Stephen F.; Turner, Richard W.; Lev, Benjamin L.

2017-03-01

Microscopic imaging of local magnetic fields provides a window into the organizing principles of complex and technologically relevant condensed-matter materials. However, a wide variety of intriguing strongly correlated and topologically nontrivial materials exhibit poorly understood phenomena outside the detection capability of state-of-the-art high-sensitivity high-resolution scanning probe magnetometers. We introduce a quantum-noise-limited scanning probe magnetometer that can operate from room-to-cryogenic temperatures with unprecedented dc-field sensitivity and micron-scale resolution. The Scanning Quantum Cryogenic Atom Microscope (SQCRAMscope) employs a magnetically levitated atomic Bose-Einstein condensate (BEC), thereby providing immunity to conductive and blackbody radiative heating. The SQCRAMscope has a field sensitivity of 1.4 nT per resolution-limited point (approximately 2 μ m ) or 6 nT /√{Hz } per point at its duty cycle. Compared to point-by-point sensors, the long length of the BEC provides a naturally parallel measurement, allowing one to measure nearly 100 points with an effective field sensitivity of 600 pT /√{Hz } for each point during the same time as a point-by-point scanner measures these points sequentially. Moreover, it has a noise floor of 300 pT and provides nearly 2 orders of magnitude improvement in magnetic flux sensitivity (down to 10-6 Φ0/√{Hz } ) over previous atomic probe magnetometers capable of scanning near samples. These capabilities are carefully benchmarked by imaging magnetic fields arising from microfabricated wire patterns in a system where samples may be scanned, cryogenically cooled, and easily exchanged. We anticipate the SQCRAMscope will provide charge-transport images at temperatures from room temperature to 4 K in unconventional superconductors and topologically nontrivial materials.

Partitioned key-value store with atomic memory operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bent, John M.; Faibish, Sorin; Grider, Gary

A partitioned key-value store is provided that supports atomic memory operations. A server performs a memory operation in a partitioned key-value store by receiving a request from an application for at least one atomic memory operation, the atomic memory operation comprising a memory address identifier; and, in response to the atomic memory operation, performing one or more of (i) reading a client-side memory location identified by the memory address identifier and storing one or more key-value pairs from the client-side memory location in a local key-value store of the server; and (ii) obtaining one or more key-value pairs from themore » local key-value store of the server and writing the obtained one or more key-value pairs into the client-side memory location identified by the memory address identifier. The server can perform functions obtained from a client-side memory location and return a result to the client using one or more of the atomic memory operations.« less

Teaching Benchmark Strategy for Fifth-Graders in Taiwan

ERIC Educational Resources Information Center

Yang, Der-Ching; Lai, M. L.

2013-01-01

The key purpose of this study was how we taught the use of benchmark strategy when comparing fraction for fifth-graders in Taiwan. 26 fifth graders from a public elementary in south Taiwan were selected to join this study. Results of this case study showed that students had a much progress on the use of benchmark strategy when comparing fraction…

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 11 2012-01-01 2012-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 11 2014-01-01 2014-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 11 2011-01-01 2011-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

7 CFR 1709.5 - Determination of energy cost benchmarks.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 11 2013-01-01 2013-01-01 false Determination of energy cost benchmarks. 1709.5... SERVICE, DEPARTMENT OF AGRICULTURE ASSISTANCE TO HIGH ENERGY COST COMMUNITIES General Requirements § 1709.5 Determination of energy cost benchmarks. (a) The Administrator shall establish, using the most...

Nomenclatural Benchmarking: The roles of digital typification and telemicroscopy

USDA-ARS?s Scientific Manuscript database

The process of nomenclatural benchmarking is the examination of type specimens of all available names to ascertain which currently accepted species the specimen bearing the name falls within. We propose a strategy for addressing four challenges for nomenclatural benchmarking. First, there is the mat...

International land Model Benchmarking (ILAMB) Package v002.00

DOE Data Explorer

Collier, Nathaniel [Oak Ridge National Laboratory; Hoffman, Forrest M. [Oak Ridge National Laboratory; Mu, Mingquan [University of California, Irvine; Randerson, James T. [University of California, Irvine; Riley, William J. [Lawrence Berkeley National Laboratory

2016-05-09

As a contribution to International Land Model Benchmarking (ILAMB) Project, we are providing new analysis approaches, benchmarking tools, and science leadership. The goal of ILAMB is to assess and improve the performance of land models through international cooperation and to inform the design of new measurement campaigns and field studies to reduce uncertainties associated with key biogeochemical processes and feedbacks. ILAMB is expected to be a primary analysis tool for CMIP6 and future model-data intercomparison experiments. This team has developed initial prototype benchmarking systems for ILAMB, which will be improved and extended to include ocean model metrics and diagnostics.

International land Model Benchmarking (ILAMB) Package v001.00

DOE Data Explorer

Mu, Mingquan [University of California, Irvine; Randerson, James T. [University of California, Irvine; Riley, William J. [Lawrence Berkeley National Laboratory; Hoffman, Forrest M. [Oak Ridge National Laboratory

2016-05-02

As a contribution to International Land Model Benchmarking (ILAMB) Project, we are providing new analysis approaches, benchmarking tools, and science leadership. The goal of ILAMB is to assess and improve the performance of land models through international cooperation and to inform the design of new measurement campaigns and field studies to reduce uncertainties associated with key biogeochemical processes and feedbacks. ILAMB is expected to be a primary analysis tool for CMIP6 and future model-data intercomparison experiments. This team has developed initial prototype benchmarking systems for ILAMB, which will be improved and extended to include ocean model metrics and diagnostics.

A Machine-to-Machine protocol benchmark for eHealth applications - Use case: Respiratory rehabilitation.

PubMed

Talaminos-Barroso, Alejandro; Estudillo-Valderrama, Miguel A; Roa, Laura M; Reina-Tosina, Javier; Ortega-Ruiz, Francisco

2016-06-01

M2M (Machine-to-Machine) communications represent one of the main pillars of the new paradigm of the Internet of Things (IoT), and is making possible new opportunities for the eHealth business. Nevertheless, the large number of M2M protocols currently available hinders the election of a suitable solution that satisfies the requirements that can demand eHealth applications. In the first place, to develop a tool that provides a benchmarking analysis in order to objectively select among the most relevant M2M protocols for eHealth solutions. In the second place, to validate the tool with a particular use case: the respiratory rehabilitation. A software tool, called Distributed Computing Framework (DFC), has been designed and developed to execute the benchmarking tests and facilitate the deployment in environments with a large number of machines, with independence of the protocol and performance metrics selected. DDS, MQTT, CoAP, JMS, AMQP and XMPP protocols were evaluated considering different specific performance metrics, including CPU usage, memory usage, bandwidth consumption, latency and jitter. The results obtained allowed to validate a case of use: respiratory rehabilitation of chronic obstructive pulmonary disease (COPD) patients in two scenarios with different types of requirement: Home-Based and Ambulatory. The results of the benchmark comparison can guide eHealth developers in the choice of M2M technologies. In this regard, the framework presented is a simple and powerful tool for the deployment of benchmark tests under specific environments and conditions. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

The Medical Library Association Benchmarking Network: development and implementation*

PubMed Central

Dudden, Rosalind Farnam; Corcoran, Kate; Kaplan, Janice; Magouirk, Jeff; Rand, Debra C.; Smith, Bernie Todd

2006-01-01

Objective: This article explores the development and implementation of the Medical Library Association (MLA) Benchmarking Network from the initial idea and test survey, to the implementation of a national survey in 2002, to the establishment of a continuing program in 2004. Started as a program for hospital libraries, it has expanded to include other nonacademic health sciences libraries. Methods: The activities and timelines of MLA's Benchmarking Network task forces and editorial board from 1998 to 2004 are described. Results: The Benchmarking Network task forces successfully developed an extensive questionnaire with parameters of size and measures of library activity and published a report of the data collected by September 2002. The data were available to all MLA members in the form of aggregate tables. Utilization of Web-based technologies proved feasible for data intake and interactive display. A companion article analyzes and presents some of the data. MLA has continued to develop the Benchmarking Network with the completion of a second survey in 2004. Conclusions: The Benchmarking Network has provided many small libraries with comparative data to present to their administrators. It is a challenge for the future to convince all MLA members to participate in this valuable program. PMID:16636702

Modification and benchmarking of MCNP for low-energy tungsten spectra.

PubMed

Mercier, J R; Kopp, D T; McDavid, W D; Dove, S B; Lancaster, J L; Tucker, D M

2000-12-01

The MCNP Monte Carlo radiation transport code was modified for diagnostic medical physics applications. In particular, the modified code was thoroughly benchmarked for the production of polychromatic tungsten x-ray spectra in the 30-150 kV range. Validating the modified code for coupled electron-photon transport with benchmark spectra was supplemented with independent electron-only and photon-only transport benchmarks. Major revisions to the code included the proper treatment of characteristic K x-ray production and scoring, new impact ionization cross sections, and new bremsstrahlung cross sections. Minor revisions included updated photon cross sections, electron-electron bremsstrahlung production, and K x-ray yield. The modified MCNP code is benchmarked to electron backscatter factors, x-ray spectra production, and primary and scatter photon transport.

The General Concept of Benchmarking and Its Application in Higher Education in Europe

ERIC Educational Resources Information Center

Nazarko, Joanicjusz; Kuzmicz, Katarzyna Anna; Szubzda-Prutis, Elzbieta; Urban, Joanna

2009-01-01

The purposes of this paper are twofold: a presentation of the theoretical basis of benchmarking and a discussion on practical benchmarking applications. Benchmarking is also analyzed as a productivity accelerator. The authors study benchmarking usage in the private and public sectors with due consideration of the specificities of the two areas.…

Benchmarking neuromorphic vision: lessons learnt from computer vision

PubMed Central

Tan, Cheston; Lallee, Stephane; Orchard, Garrick

2015-01-01

Neuromorphic Vision sensors have improved greatly since the first silicon retina was presented almost three decades ago. They have recently matured to the point where they are commercially available and can be operated by laymen. However, despite improved availability of sensors, there remains a lack of good datasets, while algorithms for processing spike-based visual data are still in their infancy. On the other hand, frame-based computer vision algorithms are far more mature, thanks in part to widely accepted datasets which allow direct comparison between algorithms and encourage competition. We are presented with a unique opportunity to shape the development of Neuromorphic Vision benchmarks and challenges by leveraging what has been learnt from the use of datasets in frame-based computer vision. Taking advantage of this opportunity, in this paper we review the role that benchmarks and challenges have played in the advancement of frame-based computer vision, and suggest guidelines for the creation of Neuromorphic Vision benchmarks and challenges. We also discuss the unique challenges faced when benchmarking Neuromorphic Vision algorithms, particularly when attempting to provide direct comparison with frame-based computer vision. PMID:26528120

Benchmarking FEniCS for mantle convection simulations

NASA Astrophysics Data System (ADS)

Vynnytska, L.; Rognes, M. E.; Clark, S. R.

2013-01-01

This paper evaluates the usability of the FEniCS Project for mantle convection simulations by numerical comparison to three established benchmarks. The benchmark problems all concern convection processes in an incompressible fluid induced by temperature or composition variations, and cover three cases: (i) steady-state convection with depth- and temperature-dependent viscosity, (ii) time-dependent convection with constant viscosity and internal heating, and (iii) a Rayleigh-Taylor instability. These problems are modeled by the Stokes equations for the fluid and advection-diffusion equations for the temperature and composition. The FEniCS Project provides a novel platform for the automated solution of differential equations by finite element methods. In particular, it offers a significant flexibility with regard to modeling and numerical discretization choices; we have here used a discontinuous Galerkin method for the numerical solution of the advection-diffusion equations. Our numerical results are in agreement with the benchmarks, and demonstrate the applicability of both the discontinuous Galerkin method and FEniCS for such applications.

Allocating scarce financial resources for HIV treatment: benchmarking prices of antiretroviral medicines in Latin America.

PubMed

Wirtz, Veronika J; Santa-Ana-Tellez, Yared; Trout, Clinton H; Kaplan, Warren A

2012-12-01

Public sector price analyses of antiretroviral (ARV) medicines can provide relevant information to detect ARV procurement procedures that do not obtain competitive market prices. Price benchmarks provide a useful tool for programme managers and policy makers to support such planning and policy measures. The aim of the study was to develop regional and global price benchmarks which can be used to analyse public-sector price variability of ARVs in low- and middle-income countries using the procurement prices of Latin America and the Caribbean (LAC) countries in 2008 as an example. We used the Global Price Reporting Mechanism (GPRM) data base, provided by the World Health Organization (WHO), for 13 LAC countries' ARV procurements to analyse the procurement prices of four first-line and three second-line ARV combinations in 2008. First, a cross-sectional analysis was conducted to compare ARV combination prices. Second, four different price 'benchmarks' were created and we estimated the additional number of patients who could have been treated in each country if the ARV combinations studied were purchased at the various reference ('benchmark') prices. Large price variations exist for first- and second-line ARV combinations between countries in the LAC region. Most countries in the LAC region could be treating between 1.17 and 3.8 times more patients if procurement prices were closer to the lowest regional generic price. For all second-line combinations, a price closer to the lowest regional innovator prices or to the global median transaction price for lower-middle-income countries would also result in treating up to nearly five times more patients. Some rational allocation of financial resources due, in part, to price benchmarking and careful planning by policy makers and programme managers can assist a country in negotiating lower ARV procurement prices and should form part of a sustainable procurement policy.

A One-group, One-dimensional Transport Benchmark in Cylindrical Geometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barry Ganapol; Abderrafi M. Ougouag

A 1-D, 1-group computational benchmark in cylndrical geometry is described. This neutron transport benchmark is useful for evaluating reactor concepts that possess azimuthal symmetry such as a pebble-bed reactor.

Key performance indicators to benchmark hospital information systems - a delphi study.

PubMed

Hübner-Bloder, G; Ammenwerth, E

2009-01-01

To identify the key performance indicators for hospital information systems (HIS) that can be used for HIS benchmarking. A Delphi survey with one qualitative and two quantitative rounds. Forty-four HIS experts from health care IT practice and academia participated in all three rounds. Seventy-seven performance indicators were identified and organized into eight categories: technical quality, software quality, architecture and interface quality, IT vendor quality, IT support and IT department quality, workflow support quality, IT outcome quality, and IT costs. The highest ranked indicators are related to clinical workflow support and user satisfaction. Isolated technical indicators or cost indicators were not seen as useful. The experts favored an interdisciplinary group of all the stakeholders, led by hospital management, to conduct the HIS benchmarking. They proposed benchmarking activities both in regular (annual) intervals as well as at defined events (for example after IT introduction). Most of the experts stated that in their institutions no HIS benchmarking activities are being performed at the moment. In the context of IT governance, IT benchmarking is gaining importance in the healthcare area. The found indicators reflect the view of health care IT professionals and researchers. Research is needed to further validate and operationalize key performance indicators, to provide an IT benchmarking framework, and to provide open repositories for a comparison of the HIS benchmarks of different hospitals.

Flameless atomic-absorption determination of gold in geological materials

USGS Publications Warehouse

Meier, A.L.

1980-01-01

Gold in geologic material is dissolved using a solution of hydrobromic acid and bromine, extracted with methyl isobutyl ketone, and determined using an atomic-absorption spectrophotometer equipped with a graphite furnace atomizer. A comparison of results obtained by this flameless atomic-absorption method on U.S. Geological Survey reference rocks and geochemical samples with reported values and with results obtained by flame atomic-absorption shows that reasonable accuracy is achieved with improved precision. The sensitivity, accuracy, and precision of the method allows acquisition of data on the distribution of gold at or below its crustal abundance. ?? 1980.

A proposed benchmark problem for cargo nuclear threat monitoring

NASA Astrophysics Data System (ADS)

Wesley Holmes, Thomas; Calderon, Adan; Peeples, Cody R.; Gardner, Robin P.

2011-10-01

There is currently a great deal of technical and political effort focused on reducing the risk of potential attacks on the United States involving radiological dispersal devices or nuclear weapons. This paper proposes a benchmark problem for gamma-ray and X-ray cargo monitoring with results calculated using MCNP5, v1.51. The primary goal is to provide a benchmark problem that will allow researchers in this area to evaluate Monte Carlo models for both speed and accuracy in both forward and inverse calculational codes and approaches for nuclear security applications. A previous benchmark problem was developed by one of the authors (RPG) for two similar oil well logging problems (Gardner and Verghese, 1991, [1]). One of those benchmarks has recently been used by at least two researchers in the nuclear threat area to evaluate the speed and accuracy of Monte Carlo codes combined with variance reduction techniques. This apparent need has prompted us to design this benchmark problem specifically for the nuclear threat researcher. This benchmark consists of conceptual design and preliminary calculational results using gamma-ray interactions on a system containing three thicknesses of three different shielding materials. A point source is placed inside the three materials lead, aluminum, and plywood. The first two materials are in right circular cylindrical form while the third is a cube. The entire system rests on a sufficiently thick lead base so as to reduce undesired scattering events. The configuration was arranged in such a manner that as gamma-ray moves from the source outward it first passes through the lead circular cylinder, then the aluminum circular cylinder, and finally the wooden cube before reaching the detector. A 2 in.×4 in.×16 in. box style NaI (Tl) detector was placed 1 m from the point source located in the center with the 4 in.×16 in. side facing the system. The two sources used in the benchmark are 137Cs and 235U.

Atomic Force Microscope

DOE Office of Scientific and Technical Information (OSTI.GOV)

Day, R.D.; Russell, P.E.

The Atomic Force Microscope (AFM) is a recently developed instrument that has achieved atomic resolution imaging of both conducting and non- conducting surfaces. Because the AFM is in the early stages of development, and because of the difficulty of building the instrument, it is currently in use in fewer than ten laboratories worldwide. It promises to be a valuable tool for obtaining information about engineering surfaces and aiding the .study of precision fabrication processes. This paper gives an overview of AFM technology and presents plans to build an instrument designed to look at engineering surfaces.

Technical Report: Installed Cost Benchmarks and Deployment Barriers for

Science.gov Websites

Cost Benchmarks and Deployment Barriers for Residential Solar Photovoltaics with Energy Storage Q1 2016 Installed Cost Benchmarks and Deployment Barriers for Residential Solar with Energy Storage Researchers from NREL published a report that provides detailed component and system-level cost breakdowns for

What Are the ACT College Readiness Benchmarks? Information Brief

ERIC Educational Resources Information Center

ACT, Inc., 2013

2013-01-01

The ACT College Readiness Benchmarks are the minimum ACT® college readiness assessment scores required for students to have a high probability of success in credit-bearing college courses--English Composition, social sciences courses, College Algebra, or Biology. This report identifies the College Readiness Benchmarks on the ACT Compass scale…

Apples to Oranges: Benchmarking Vocational Education and Training Programmes

ERIC Educational Resources Information Center

Bogetoft, Peter; Wittrup, Jesper

2017-01-01

This paper discusses methods for benchmarking vocational education and training colleges and presents results from a number of models. It is conceptually difficult to benchmark vocational colleges. The colleges typically offer a wide range of course programmes, and the students come from different socioeconomic backgrounds. We solve the…

Pulse radiolysis studies of the reactions of bromine atoms and dimethyl sulfoxide bromine atom complexes with alcohols

NASA Astrophysics Data System (ADS)

Sumiyoshi, Takashi; Fujiyoshi, Ryoko; Katagiri, Miho; Sawamura, Sadashi

2007-05-01

Dimethylsulfoxide (DMSO)-Br complexes were generated by pulse radiolysis of DMSO/bromomethane mixtures and the formation mechanism and spectral characteristics of the formed complexes were investigated in detail. The rate constant for the reaction of bromine atoms with DMSO and the extinction coefficient of the complex were obtained to be 4.6×10 9 M -1 s -1 and 6300 M -1 cm -1 at the absorption maximum of 430 nm. Rate constants for the reaction of bromine atoms with a series of alcohols were determined in CBrCl 3 solutions applying a competitive kinetic method using the DMSO-Br complex as the reference system. The obtained rate constants were ˜10 8 M -1 s -1, one or two orders larger than those reported for highly polar solvents. Rate constants of DMSO-Br complexes with alcohols were determined to be ˜ 10 7 M -1 s -1. A comparison of the reactivities of Br atoms and DMSO-Br complexes with those of chlorine atoms and chlorine atom complexes which are ascribed to hydrogen abstracting reactants strongly indicates that hydrogen abstraction from alcohols is not the rate determining step in the case of Br atoms and DMSO-Br complexes.

Benchmarking quantum mechanical calculations with experimental NMR chemical shifts of 2-HADNT

NASA Astrophysics Data System (ADS)

Liu, Yuemin; Junk, Thomas; Liu, Yucheng; Tzeng, Nianfeng; Perkins, Richard

2015-04-01

In this study, both GIAO-DFT and GIAO-MP2 calculations of nuclear magnetic resonance (NMR) spectra were benchmarked with experimental chemical shifts. The experimental chemical shifts were determined experimentally for carbon-13 (C-13) of seven carbon atoms for the TNT degradation product 2-hydroxylamino-4,6-dinitrotoluene (2-HADNT). Quantum mechanics GIAO calculations were implemented using Becke-3-Lee-Yang-Parr (B3LYP) and other six hybrid DFT methods (Becke-1-Lee-Yang-Parr (B1LYP), Becke-half-and-half-Lee-Yang-Parr (BH and HLYP), Cohen-Handy-3-Lee-Yang-Parr (O3LYP), Coulomb-attenuating-B3LYP (CAM-B3LYP), modified-Perdew-Wang-91-Lee-Yang-Parr (mPW1LYP), and Xu-3-Lee-Yang-Parr (X3LYP)) which use the same correlation functional LYP. Calculation results showed that the GIAO-MP2 method gives the most accurate chemical shift values, and O3LYP method provides the best prediction of chemical shifts among the B3LYP and other five DFT methods. Three types of atomic partial charges, Mulliken (MK), electrostatic potential (ESP), and natural bond orbital (NBO), were also calculated using MP2/aug-cc-pVDZ method. A reasonable correlation was discovered between NBO partial charges and experimental chemical shifts of carbon-13 (C-13).

Implementation and validation of a conceptual benchmarking framework for patient blood management.

PubMed

Kastner, Peter; Breznik, Nada; Gombotz, Hans; Hofmann, Axel; Schreier, Günter

2015-01-01

Public health authorities and healthcare professionals are obliged to ensure high quality health service. Because of the high variability of the utilisation of blood and blood components, benchmarking is indicated in transfusion medicine. Implementation and validation of a benchmarking framework for Patient Blood Management (PBM) based on the report from the second Austrian Benchmark trial. Core modules for automatic report generation have been implemented with KNIME (Konstanz Information Miner) and validated by comparing the output with the results of the second Austrian benchmark trial. Delta analysis shows a deviation <0.1% for 95% (max. 1.4%). The framework provides a reliable tool for PBM benchmarking. The next step is technical integration with hospital information systems.

Benchmarking multimedia performance

NASA Astrophysics Data System (ADS)

Zandi, Ahmad; Sudharsanan, Subramania I.

1998-03-01

With the introduction of faster processors and special instruction sets tailored to multimedia, a number of exciting applications are now feasible on the desktops. Among these is the DVD playback consisting, among other things, of MPEG-2 video and Dolby digital audio or MPEG-2 audio. Other multimedia applications such as video conferencing and speech recognition are also becoming popular on computer systems. In view of this tremendous interest in multimedia, a group of major computer companies have formed, Multimedia Benchmarks Committee as part of Standard Performance Evaluation Corp. to address the performance issues of multimedia applications. The approach is multi-tiered with three tiers of fidelity from minimal to full compliant. In each case the fidelity of the bitstream reconstruction as well as quality of the video or audio output are measured and the system is classified accordingly. At the next step the performance of the system is measured. In many multimedia applications such as the DVD playback the application needs to be run at a specific rate. In this case the measurement of the excess processing power, makes all the difference. All these make a system level, application based, multimedia benchmark very challenging. Several ideas and methodologies for each aspect of the problems will be presented and analyzed.

Benchmarks Momentum on Increase

ERIC Educational Resources Information Center

McNeil, Michele

2008-01-01

No longer content with the patchwork quilt of assessments used to measure states' K-12 performance, top policy groups are pushing states toward international benchmarking as a way to better prepare students for a competitive global economy. The National Governors Association, the Council of Chief State School Officers, and the standards-advocacy…

Benchmarks: WICHE Region 2012

ERIC Educational Resources Information Center

Western Interstate Commission for Higher Education, 2013

2013-01-01

Benchmarks: WICHE Region 2012 presents information on the West's progress in improving access to, success in, and financing of higher education. The information is updated annually to monitor change over time and encourage its use as a tool for informed discussion in policy and education communities. To establish a general context for the…

Fingerprinting sea-level variations in response to continental ice loss: a benchmark exercise

NASA Astrophysics Data System (ADS)

Barletta, Valentina R.; Spada, Giorgio; Riva, Riccardo E. M.; James, Thomas S.; Simon, Karen M.; van der Wal, Wouter; Martinec, Zdenek; Klemann, Volker; Olsson, Per-Anders; Hagedoorn, Jan; Stocchi, Paolo; Vermeersen, Bert

2013-04-01

Understanding the response of the Earth to the waxing and waning ice sheets is crucial in various contexts, ranging from the interpretation of modern satellite geodetic measurements to the projections of future sea level trends in response to climate change. All the processes accompanying Glacial Isostatic Adjustment (GIA) can be described solving the so-called Sea Level Equation (SLE), an integral equation that accounts for the interactions between the ice sheets, the solid Earth, and the oceans. Modern approaches to the SLE are based on various techniques that range from purely analytical formulations to fully numerical methods. Here we present the results of a benchmark exercise of independently developed codes designed to solve the SLE. The study involves predictions of current sea level changes due to present-day ice mass loss. In spite of the differences in the methods employed, the comparison shows that a significant number of GIA modellers can reproduce their sea-level computations within 2% for well defined, large-scale present-day ice mass changes. Smaller and more detailed loads need further and dedicated benchmarking and high resolution computation. This study shows how the details of the implementation and the inputs specifications are an important, and often underappreciated, aspect. Hence this represents a step toward the assessment of reliability of sea level projections obtained with benchmarked SLE codes.

A review on the benchmarking concept in Malaysian construction safety performance

NASA Astrophysics Data System (ADS)

Ishak, Nurfadzillah; Azizan, Muhammad Azizi

2018-02-01

Construction industry is one of the major industries that propels Malaysia's economy in highly contributes to our nation's GDP growth, yet the high fatality rates on construction sites have caused concern among safety practitioners and the stakeholders. Hence, there is a need of benchmarking in performance of Malaysia's construction industry especially in terms of safety. This concept can create a fertile ground for ideas, but only in a receptive environment, organization that share good practices and compare their safety performance against other benefit most to establish improvement in safety culture. This research was conducted to study the awareness important, evaluate current practice and improvement, and also identify the constraint in implement of benchmarking on safety performance in our industry. Additionally, interviews with construction professionals were come out with different views on this concept. Comparison has been done to show the different understanding of benchmarking approach and how safety performance can be benchmarked. But, it's viewed as one mission, which to evaluate objectives identified through benchmarking that will improve the organization's safety performance. Finally, the expected result from this research is to help Malaysia's construction industry implement best practice in safety performance management through the concept of benchmarking.

Towards routine determination of focal mechanisms obtained from first motion P-wave arrivals

NASA Astrophysics Data System (ADS)

Lentas, K.

2018-03-01

The Bulletin of the International Seismological Centre (ISC) contains information on earthquake mechanisms collected from many different sources including national and global agencies, resulting in a satisfactory coverage over a wide magnitude range (M ˜2-9). Nevertheless, there are still a vast number of earthquakes with no reported source mechanisms especially for magnitudes up to 5. This study investigates the possibility of calculating earthquake focal mechanisms in a routine and systematic way based on P-wave first motion polarities. Any available parametric data in the ISC database is being used, as well as auto-picked polarities from waveform data up to teleseismic epicentral distances (90°) for stations that are not reported to the ISC. The determination of the earthquake mechanisms is carried out with a modified version of the HASH algorithm that is compatible with a wide range of epicentral distances and takes into account the ellipsoids defined by the ISC location errors, and the Earth's structure uncertainties. Initially, benchmark tests for a set of ISC reviewed earthquakes (mb > 4.5) are carried out and the HASH mechanism classification scheme is used to define the mechanism quality. Focal mechanisms of quality A, B and C with an azimuthal gap up to 90° compare well to the benchmark mechanisms. Nevertheless, the majority of the obtained mechanisms fall into class D as a result of limited polarity data from stations in local/regional epicentral distances. Specifically, the computation of the minimum rotation angle between the obtained mechanisms and the benchmarks, reveals that 41 per cent of the examined earthquakes show rotation angles up to 35°. Finally, the current technique is applied to a small set of earthquakes from the reviewed ISC bulletin where 62 earthquakes, with no previously reported source mechanisms, are successfully obtained.

Kinetic energy of shakeoff atomic electrons from 37K β+ decay

NASA Astrophysics Data System (ADS)

Behr, J. A.; Gorelov, A.; Farfan, C.; Smale, S.; Olchanski, K.; Kurchananov, L.; Anholm, M.; Behling, R. S.; Fenker, B.; Shidling, P. D.; Mehlman, M.; Melconian, D.; Ashery, D.; Gwinner, G.; Trinat Collaboration

2013-10-01

We have measured the kinetic energies from 0 to 30 eV of atomic shakeoff electrons from the β+ decay of 37K. Despite much experimental and theoretical work on the distribution of final ion charge states, shakeoff electrons from β- decay have only been measured with energies above 150 eV [Mitrokhovich, Nucl. Phys. Atom. Energy, 11, 125 (2010)]. We use our magneto-optical trap's time-varying magnetic quadrupole field combined with a uniform electric field as a spectrometer. Our result has more 15 eV electrons than a model using the sudden approximation and hydrogenic wavefunctions [Levinger, Phys. Rev. 90, 11 (1958)]. The total energy carried away by electrons is, as expected, a negligible correction to superallowed Ft values. Understanding the energy of these low-energy electrons is important for their use in precision β decay to select events coming from trapped atoms and start time-of-flight for the recoil ions. Our results could provide a benchmark for shakeoff electron calculations used for biological radiation damage [Lee, Comp. Math. Meth in Medicine doi:10.1155/2012/651475]. Support: NSERC, NRC through TRIUMF, DOE ER41747 ER40773, State of Texas, Israel Science Foundation.

Effects of benchmarking on the quality of type 2 diabetes care: results of the OPTIMISE (Optimal Type 2 Diabetes Management Including Benchmarking and Standard Treatment) study in Greece

PubMed Central

Tsimihodimos, Vasilis; Kostapanos, Michael S.; Moulis, Alexandros; Nikas, Nikos; Elisaf, Moses S.

2015-01-01

Objectives: To investigate the effect of benchmarking on the quality of type 2 diabetes (T2DM) care in Greece. Methods: The OPTIMISE (Optimal Type 2 Diabetes Management Including Benchmarking and Standard Treatment) study [ClinicalTrials.gov identifier: NCT00681850] was an international multicenter, prospective cohort study. It included physicians randomized 3:1 to either receive benchmarking for glycated hemoglobin (HbA1c), systolic blood pressure (SBP) and low-density lipoprotein cholesterol (LDL-C) treatment targets (benchmarking group) or not (control group). The proportions of patients achieving the targets of the above-mentioned parameters were compared between groups after 12 months of treatment. Also, the proportions of patients achieving those targets at 12 months were compared with baseline in the benchmarking group. Results: In the Greek region, the OPTIMISE study included 797 adults with T2DM (570 in the benchmarking group). At month 12 the proportion of patients within the predefined targets for SBP and LDL-C was greater in the benchmarking compared with the control group (50.6 versus 35.8%, and 45.3 versus 36.1%, respectively). However, these differences were not statistically significant. No difference between groups was noted in the percentage of patients achieving the predefined target for HbA1c. At month 12 the increase in the percentage of patients achieving all three targets was greater in the benchmarking (5.9–15.0%) than in the control group (2.7–8.1%). In the benchmarking group more patients were on target regarding SBP (50.6% versus 29.8%), LDL-C (45.3% versus 31.3%) and HbA1c (63.8% versus 51.2%) at 12 months compared with baseline (p < 0.001 for all comparisons). Conclusion: Benchmarking may comprise a promising tool for improving the quality of T2DM care. Nevertheless, target achievement rates of each, and of all three, quality indicators were suboptimal, indicating there are still unmet needs in the management of T2DM. PMID:26445642

Benchmarking methods and data sets for ligand enrichment assessment in virtual screening.

PubMed

Xia, Jie; Tilahun, Ermias Lemma; Reid, Terry-Elinor; Zhang, Liangren; Wang, Xiang Simon

2015-01-01

Retrospective small-scale virtual screening (VS) based on benchmarking data sets has been widely used to estimate ligand enrichments of VS approaches in the prospective (i.e. real-world) efforts. However, the intrinsic differences of benchmarking sets to the real screening chemical libraries can cause biased assessment. Herein, we summarize the history of benchmarking methods as well as data sets and highlight three main types of biases found in benchmarking sets, i.e. "analogue bias", "artificial enrichment" and "false negative". In addition, we introduce our recent algorithm to build maximum-unbiased benchmarking sets applicable to both ligand-based and structure-based VS approaches, and its implementations to three important human histone deacetylases (HDACs) isoforms, i.e. HDAC1, HDAC6 and HDAC8. The leave-one-out cross-validation (LOO CV) demonstrates that the benchmarking sets built by our algorithm are maximum-unbiased as measured by property matching, ROC curves and AUCs. Copyright © 2014 Elsevier Inc. All rights reserved.

Benchmarking Methods and Data Sets for Ligand Enrichment Assessment in Virtual Screening

PubMed Central

Xia, Jie; Tilahun, Ermias Lemma; Reid, Terry-Elinor; Zhang, Liangren; Wang, Xiang Simon

2014-01-01

Retrospective small-scale virtual screening (VS) based on benchmarking data sets has been widely used to estimate ligand enrichments of VS approaches in the prospective (i.e. real-world) efforts. However, the intrinsic differences of benchmarking sets to the real screening chemical libraries can cause biased assessment. Herein, we summarize the history of benchmarking methods as well as data sets and highlight three main types of biases found in benchmarking sets, i.e. “analogue bias”, “artificial enrichment” and “false negative”. In addition, we introduced our recent algorithm to build maximum-unbiased benchmarking sets applicable to both ligand-based and structure-based VS approaches, and its implementations to three important human histone deacetylase (HDAC) isoforms, i.e. HDAC1, HDAC6 and HDAC8. The Leave-One-Out Cross-Validation (LOO CV) demonstrates that the benchmarking sets built by our algorithm are maximum-unbiased in terms of property matching, ROC curves and AUCs. PMID:25481478

Requirements for benchmarking personal image retrieval systems

NASA Astrophysics Data System (ADS)

Bouguet, Jean-Yves; Dulong, Carole; Kozintsev, Igor; Wu, Yi

2006-01-01

It is now common to have accumulated tens of thousands of personal ictures. Efficient access to that many pictures can only be done with a robust image retrieval system. This application is of high interest to Intel processor architects. It is highly compute intensive, and could motivate end users to upgrade their personal computers to the next generations of processors. A key question is how to assess the robustness of a personal image retrieval system. Personal image databases are very different from digital libraries that have been used by many Content Based Image Retrieval Systems.1 For example a personal image database has a lot of pictures of people, but a small set of different people typically family, relatives, and friends. Pictures are taken in a limited set of places like home, work, school, and vacation destination. The most frequent queries are searched for people, and for places. These attributes, and many others affect how a personal image retrieval system should be benchmarked, and benchmarks need to be different from existing ones based on art images, or medical images for examples. The attributes of the data set do not change the list of components needed for the benchmarking of such systems as specified in2: - data sets - query tasks - ground truth - evaluation measures - benchmarking events. This paper proposed a way to build these components to be representative of personal image databases, and of the corresponding usage models.

Atom-by-atom assembly

NASA Astrophysics Data System (ADS)

Hla, Saw Wai

2014-05-01

Atomic manipulation using a scanning tunneling microscope (STM) tip enables the construction of quantum structures on an atom-by-atom basis, as well as the investigation of the electronic and dynamical properties of individual atoms on a one-atom-at-a-time basis. An STM is not only an instrument that is used to ‘see’ individual atoms by means of imaging, but is also a tool that is used to ‘touch’ and ‘take’ the atoms, or to ‘hear’ their movements. Therefore, the STM can be considered as the ‘eyes’, ‘hands’ and ‘ears’ of the scientists, connecting our macroscopic world to the exciting atomic world. In this article, various STM atom manipulation schemes and their example applications are described. The future directions of atomic level assembly on surfaces using scanning probe tips are also discussed.

Toxicological benchmarks for screening potential contaminants of concern for effects on aquatic biota: 1996 revision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suter, G.W. II; Tsao, C.L.

1996-06-01

This report presents potential screening benchmarks for protection of aquatic life form contaminants in water. Because there is no guidance for screening for benchmarks, a set of alternative benchmarks is presented herein. This report presents the alternative benchmarks for chemicals that have been detected on the Oak Ridge Reservation. It also presents the data used to calculate the benchmarks and the sources of the data. It compares the benchmarks and discusses their relative conservatism and utility. Also included is the updates of benchmark values where appropriate, new benchmark values, secondary sources are replaced by primary sources, and a more completemore » documentation of the sources and derivation of all values are presented.« less

Implementation of the NAS Parallel Benchmarks in Java

NASA Technical Reports Server (NTRS)

Frumkin, Michael A.; Schultz, Matthew; Jin, Haoqiang; Yan, Jerry; Biegel, Bryan (Technical Monitor)

2002-01-01

Several features make Java an attractive choice for High Performance Computing (HPC). In order to gauge the applicability of Java to Computational Fluid Dynamics (CFD), we have implemented the NAS (NASA Advanced Supercomputing) Parallel Benchmarks in Java. The performance and scalability of the benchmarks point out the areas where improvement in Java compiler technology and in Java thread implementation would position Java closer to Fortran in the competition for CFD applications.

Accurate Mapping of Multilevel Rydberg Atoms on Interacting Spin-1 /2 Particles for the Quantum Simulation of Ising Models

NASA Astrophysics Data System (ADS)

de Léséleuc, Sylvain; Weber, Sebastian; Lienhard, Vincent; Barredo, Daniel; Büchler, Hans Peter; Lahaye, Thierry; Browaeys, Antoine

2018-03-01

We study a system of atoms that are laser driven to n D3 /2 Rydberg states and assess how accurately they can be mapped onto spin-1 /2 particles for the quantum simulation of anisotropic Ising magnets. Using nonperturbative calculations of the pair potentials between two atoms in the presence of electric and magnetic fields, we emphasize the importance of a careful selection of experimental parameters in order to maintain the Rydberg blockade and avoid excitation of unwanted Rydberg states. We benchmark these theoretical observations against experiments using two atoms. Finally, we show that in these conditions, the experimental dynamics observed after a quench is in good agreement with numerical simulations of spin-1 /2 Ising models in systems with up to 49 spins, for which numerical simulations become intractable.

Integral Full Core Multi-Physics PWR Benchmark with Measured Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Forget, Benoit; Smith, Kord; Kumar, Shikhar

In recent years, the importance of modeling and simulation has been highlighted extensively in the DOE research portfolio with concrete examples in nuclear engineering with the CASL and NEAMS programs. These research efforts and similar efforts worldwide aim at the development of high-fidelity multi-physics analysis tools for the simulation of current and next-generation nuclear power reactors. Like all analysis tools, verification and validation is essential to guarantee proper functioning of the software and methods employed. The current approach relies mainly on the validation of single physic phenomena (e.g. critical experiment, flow loops, etc.) and there is a lack of relevantmore » multiphysics benchmark measurements that are necessary to validate high-fidelity methods being developed today. This work introduces a new multi-cycle full-core Pressurized Water Reactor (PWR) depletion benchmark based on two operational cycles of a commercial nuclear power plant that provides a detailed description of fuel assemblies, burnable absorbers, in-core fission detectors, core loading and re-loading patterns. This benchmark enables analysts to develop extremely detailed reactor core models that can be used for testing and validation of coupled neutron transport, thermal-hydraulics, and fuel isotopic depletion. The benchmark also provides measured reactor data for Hot Zero Power (HZP) physics tests, boron letdown curves, and three-dimensional in-core flux maps from 58 instrumented assemblies. The benchmark description is now available online and has been used by many groups. However, much work remains to be done on the quantification of uncertainties and modeling sensitivities. This work aims to address these deficiencies and make this benchmark a true non-proprietary international benchmark for the validation of high-fidelity tools. This report details the BEAVRS uncertainty quantification for the first two cycle of operations and serves as the final report of the

Atomization simulations using an Eulerian-VOF-Lagrangian method

NASA Technical Reports Server (NTRS)

Chen, Yen-Sen; Shang, Huan-Min; Liaw, Paul; Chen, C. P.

1994-01-01

This paper summarizes the technical development and validation of a multiphase computational fluid dynamics (CFD) numerical method using the volume-of-fluid (VOF) model and a Lagrangian tracking model which can be employed to analyze general multiphase flow problems with free surface mechanism. The gas-liquid interface mass, momentum and energy conservations are modeled by continuum surface mechanisms. A new solution method is developed such that the present VOF model can be applied for all-speed flow regimes. The objectives of the present study are to develop and verify the fractional volume-of-fluid cell partitioning approach into a predictor-corrector algorithm and to demonstrate the effectiveness of the present innovative approach by simulating benchmark problems including the coaxial jet atomization.

Benchmarking of venous thromboembolism prophylaxis practice with ENT.UK guidelines.

PubMed

Al-Qahtani, Ali S

2017-05-01

The aim of this study was to benchmark our guidelines of prevention of venous thromboembolism (VTE) in ENT surgical population against ENT.UK guidelines, and also to encourage healthcare providers to utilize benchmarking as an effective method of improving performance. The study design is prospective descriptive analysis. The setting of this study is tertiary referral centre (Assir Central Hospital, Abha, Saudi Arabia). In this study, we are benchmarking our practice guidelines of the prevention of VTE in the ENT surgical population against that of ENT.UK guidelines to mitigate any gaps. ENT guidelines 2010 were downloaded from the ENT.UK Website. Our guidelines were compared with the possibilities that either our performance meets or fall short of ENT.UK guidelines. Immediate corrective actions will take place if there is quality chasm between the two guidelines. ENT.UK guidelines are evidence-based and updated which may serve as role-model for adoption and benchmarking. Our guidelines were accordingly amended to contain all factors required in providing a quality service to ENT surgical patients. While not given appropriate attention, benchmarking is a useful tool in improving quality of health care. It allows learning from others' practices and experiences, and works towards closing any quality gaps. In addition, benchmarking clinical outcomes is critical for quality improvement and informing decisions concerning service provision. It is recommended to be included on the list of quality improvement methods of healthcare services.

Hyperfine state entanglement of spinor BEC and scattering atom

NASA Astrophysics Data System (ADS)

Li, Zhibing; Bao, Chengguang; Zheng, Wei

2018-05-01

Condensate of spin-1 atoms frozen in a unique spatial mode may possess large internal degrees of freedom. The scattering amplitudes of polarized cold atoms scattered by the condensate are obtained with the method of fractional parentage coefficients that treats the spin degrees of freedom rigorously. Channels with scattering cross sections enhanced by the square of the atom number of the condensate are found. Entanglement between the condensate and the propagating atom can be established by scattering. Entanglement entropy is analytically obtained for arbitrary initial states. Our results also give a hint for the establishment of quantum thermal ensembles in the hyperfine space of spin states.

Issues in benchmarking human reliability analysis methods : a literature review.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lois, Erasmia; Forester, John Alan; Tran, Tuan Q.

There is a diversity of human reliability analysis (HRA) methods available for use in assessing human performance within probabilistic risk assessment (PRA). Due to the significant differences in the methods, including the scope, approach, and underlying models, there is a need for an empirical comparison investigating the validity and reliability of the methods. To accomplish this empirical comparison, a benchmarking study is currently underway that compares HRA methods with each other and against operator performance in simulator studies. In order to account for as many effects as possible in the construction of this benchmarking study, a literature review was conducted,more » reviewing past benchmarking studies in the areas of psychology and risk assessment. A number of lessons learned through these studies are presented in order to aid in the design of future HRA benchmarking endeavors.« less

Issues in Benchmarking Human Reliability Analysis Methods: A Literature Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ronald L. Boring; Stacey M. L. Hendrickson; John A. Forester

There is a diversity of human reliability analysis (HRA) methods available for use in assessing human performance within probabilistic risk assessments (PRA). Due to the significant differences in the methods, including the scope, approach, and underlying models, there is a need for an empirical comparison investigating the validity and reliability of the methods. To accomplish this empirical comparison, a benchmarking study comparing and evaluating HRA methods in assessing operator performance in simulator experiments is currently underway. In order to account for as many effects as possible in the construction of this benchmarking study, a literature review was conducted, reviewing pastmore » benchmarking studies in the areas of psychology and risk assessment. A number of lessons learned through these studies are presented in order to aid in the design of future HRA benchmarking endeavors.« less

Benchmarking of Heavy Ion Transport Codes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Remec, Igor; Ronningen, Reginald M.; Heilbronn, Lawrence

Accurate prediction of radiation fields generated by heavy ion interactions is important in medical applications, space missions, and in designing and operation of rare isotope research facilities. In recent years, several well-established computer codes in widespread use for particle and radiation transport calculations have been equipped with the capability to simulate heavy ion transport and interactions. To assess and validate these capabilities, we performed simulations of a series of benchmark-quality heavy ion experiments with the computer codes FLUKA, MARS15, MCNPX, and PHITS. We focus on the comparisons of secondary neutron production. Results are encouraging; however, further improvements in models andmore » codes and additional benchmarking are required.« less

Photoelectron angular distributions for states of any mixed character: An experiment-friendly model for atomic, molecular, and cluster anions

NASA Astrophysics Data System (ADS)

Khuseynov, Dmitry; Blackstone, Christopher C.; Culberson, Lori M.; Sanov, Andrei

2014-09-01

We present a model for laboratory-frame photoelectron angular distributions in direct photodetachment from (in principle) any molecular orbital using linearly polarized light. A transparent mathematical approach is used to generalize the Cooper-Zare central-potential model to anionic states of any mixed character. In the limit of atomic-anion photodetachment, the model reproduces the Cooper-Zare formula. In the case of an initial orbital described as a superposition of s and p-type functions, the model yields the previously obtained s-p mixing formula. The formalism is further advanced using the Hanstorp approximation, whereas the relative scaling of the partial-wave cross-sections is assumed to follow the Wigner threshold law. The resulting model describes the energy dependence of photoelectron anisotropy for any atomic, molecular, or cluster anions, usually without requiring a direct calculation of the transition dipole matrix elements. As a benchmark case, we apply the p-d variant of the model to the experimental results for NO- photodetachment and show that the observed anisotropy trend is described well using physically meaningful values of the model parameters. Overall, the presented formalism delivers insight into the photodetachment process and affords a new quantitative strategy for analyzing the photoelectron angular distributions and characterizing mixed-character molecular orbitals using photoelectron imaging spectroscopy of negative ions.

Photoelectron angular distributions for states of any mixed character: an experiment-friendly model for atomic, molecular, and cluster anions.

PubMed

Khuseynov, Dmitry; Blackstone, Christopher C; Culberson, Lori M; Sanov, Andrei

2014-09-28

We present a model for laboratory-frame photoelectron angular distributions in direct photodetachment from (in principle) any molecular orbital using linearly polarized light. A transparent mathematical approach is used to generalize the Cooper-Zare central-potential model to anionic states of any mixed character. In the limit of atomic-anion photodetachment, the model reproduces the Cooper-Zare formula. In the case of an initial orbital described as a superposition of s and p-type functions, the model yields the previously obtained s-p mixing formula. The formalism is further advanced using the Hanstorp approximation, whereas the relative scaling of the partial-wave cross-sections is assumed to follow the Wigner threshold law. The resulting model describes the energy dependence of photoelectron anisotropy for any atomic, molecular, or cluster anions, usually without requiring a direct calculation of the transition dipole matrix elements. As a benchmark case, we apply the p-d variant of the model to the experimental results for NO(-) photodetachment and show that the observed anisotropy trend is described well using physically meaningful values of the model parameters. Overall, the presented formalism delivers insight into the photodetachment process and affords a new quantitative strategy for analyzing the photoelectron angular distributions and characterizing mixed-character molecular orbitals using photoelectron imaging spectroscopy of negative ions.

Neutron Reference Benchmark Field Specifications: ACRR Polyethylene-Lead-Graphite (PLG) Bucket Environment (ACRR-PLG-CC-32-CL).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vega, Richard Manuel; Parm, Edward J.; Griffin, Patrick J.

2015-07-01

This report was put together to support the International Atomic Energy Agency (IAEA) REAL- 2016 activity to validate the dosimetry community’s ability to use a consistent set of activation data and to derive consistent spectral characterizations. The report captures details of integral measurements taken in the Annular Core Research Reactor (ACRR) central cavity with the Polyethylene-Lead-Graphite (PLG) bucket, reference neutron benchmark field. The field is described and an “a priori” calculated neutron spectrum is reported, based on MCNP6 calculations, and a subject matter expert (SME) based covariance matrix is given for this “a priori” spectrum. The results of 37 integralmore » dosimetry measurements in the neutron field are reported.« less

NAS Parallel Benchmark Results 11-96. 1.0

NASA Technical Reports Server (NTRS)

Bailey, David H.; Bailey, David; Chancellor, Marisa K. (Technical Monitor)

1997-01-01

The NAS Parallel Benchmarks have been developed at NASA Ames Research Center to study the performance of parallel supercomputers. The eight benchmark problems are specified in a "pencil and paper" fashion. In other words, the complete details of the problem to be solved are given in a technical document, and except for a few restrictions, benchmarkers are free to select the language constructs and implementation techniques best suited for a particular system. These results represent the best results that have been reported to us by the vendors for the specific 3 systems listed. In this report, we present new NPB (Version 1.0) performance results for the following systems: DEC Alpha Server 8400 5/440, Fujitsu VPP Series (VX, VPP300, and VPP700), HP/Convex Exemplar SPP2000, IBM RS/6000 SP P2SC node (120 MHz), NEC SX-4/32, SGI/CRAY T3E, SGI Origin200, and SGI Origin2000. We also report High Performance Fortran (HPF) based NPB results for IBM SP2 Wide Nodes, HP/Convex Exemplar SPP2000, and SGI/CRAY T3D. These results have been submitted by Applied Parallel Research (APR) and Portland Group Inc. (PGI). We also present sustained performance per dollar for Class B LU, SP and BT benchmarks.

Engine Benchmarking - Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wallner, Thomas

Detailed benchmarking of the powertrains of three light-duty vehicles was performed. Results were presented and provided to CRADA partners. The vehicles included a MY2011 Audi A4, a MY2012 Mini Cooper and a MY2014 Nissan Versa.

[Benchmarking of university trauma centers in Germany. Research and teaching].

PubMed

Gebhard, F; Raschke, M; Ruchholtz, S; Meffert, R; Marzi, I; Pohlemann, T; Südkamp, N; Josten, C; Zwipp, H

2011-07-01

Benchmarking is a very popular business process and meanwhile is used in research as well. The aim of the present study is to elucidate key numbers of German university trauma departments regarding research and teaching. The data set is based upon the monthly reports given by the administration in each university. As a result the study shows that only well-known parameters such as fund-raising and impact factors can be used to benchmark university-based trauma centers. The German federal system does not allow a nationwide benchmarking.

Benchmarking for maximum value.

PubMed

Baldwin, Ed

2009-03-01

Speaking at the most recent Healthcare Estates conference, Ed Baldwin, of international built asset consultancy EC Harris LLP, examined the role of benchmarking and market-testing--two of the key methods used to evaluate the quality and cost-effectiveness of hard and soft FM services provided under PFI healthcare schemes to ensure they are offering maximum value for money.

MARC calculations for the second WIPP structural benchmark problem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, H.S.

1981-05-01

This report describes calculations made with the MARC structural finite element code for the second WIPP structural benchmark problem. Specific aspects of problem implementation such as element choice, slip line modeling, creep law implementation, and thermal-mechanical coupling are discussed in detail. Also included are the computational results specified in the benchmark problem formulation.

Local implementation of the Essence of Care benchmarks.

PubMed

Jones, Sue

To understand clinical practice benchmarking from the perspective of nurses working in a large acute NHS trust and to determine whether the nurses perceived that their commitment to Essence of Care led to improvements in care, the factors that influenced their role in the process and the organisational factors that influenced benchmarking. An ethnographic case study approach was adopted. Six themes emerged from the data. Two organisational issues emerged: leadership and the values and/or culture of the organisation. The findings suggested that the leadership ability of the Essence of Care link nurses and the value placed on this work by the organisation were key to the success of benchmarking. A model for successful implementation of the Essence of Care is proposed based on the findings of this study, which lends itself to testing by other organisations.

Robust validation of approximate 1-matrix functionals with few-electron harmonium atoms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cioslowski, Jerzy, E-mail: jerzy@wmf.univ.szczecin.pl; Piris, Mario; Matito, Eduard

2015-12-07

A simple comparison between the exact and approximate correlation components U of the electron-electron repulsion energy of several states of few-electron harmonium atoms with varying confinement strengths provides a stringent validation tool for 1-matrix functionals. The robustness of this tool is clearly demonstrated in a survey of 14 known functionals, which reveals their substandard performance within different electron correlation regimes. Unlike spot-testing that employs dissociation curves of diatomic molecules or more extensive benchmarking against experimental atomization energies of molecules comprising some standard set, the present approach not only uncovers the flaws and patent failures of the functionals but, even moremore » importantly, also allows for pinpointing their root causes. Since the approximate values of U are computed at exact 1-densities, the testing requires minimal programming and thus is particularly suitable for rapid screening of new functionals.« less

Benchmarking for On-Scalp MEG Sensors.

PubMed

Xie, Minshu; Schneiderman, Justin F; Chukharkin, Maxim L; Kalabukhov, Alexei; Riaz, Bushra; Lundqvist, Daniel; Whitmarsh, Stephen; Hamalainen, Matti; Jousmaki, Veikko; Oostenveld, Robert; Winkler, Dag

2017-06-01

We present a benchmarking protocol for quantitatively comparing emerging on-scalp magnetoencephalography (MEG) sensor technologies to their counterparts in state-of-the-art MEG systems. As a means of validation, we compare a high-critical-temperature superconducting quantum interference device (high T c SQUID) with the low- T c SQUIDs of an Elekta Neuromag TRIUX system in MEG recordings of auditory and somatosensory evoked fields (SEFs) on one human subject. We measure the expected signal gain for the auditory-evoked fields (deeper sources) and notice some unfamiliar features in the on-scalp sensor-based recordings of SEFs (shallower sources). The experimental results serve as a proof of principle for the benchmarking protocol. This approach is straightforward, general to various on-scalp MEG sensors, and convenient to use on human subjects. The unexpected features in the SEFs suggest on-scalp MEG sensors may reveal information about neuromagnetic sources that is otherwise difficult to extract from state-of-the-art MEG recordings. As the first systematically established on-scalp MEG benchmarking protocol, magnetic sensor developers can employ this method to prove the utility of their technology in MEG recordings. Further exploration of the SEFs with on-scalp MEG sensors may reveal unique information about their sources.

A new numerical benchmark for variably saturated variable-density flow and transport in porous media

NASA Astrophysics Data System (ADS)

Guevara, Carlos; Graf, Thomas

2016-04-01

In subsurface hydrological systems, spatial and temporal variations in solute concentration and/or temperature may affect fluid density and viscosity. These variations could lead to potentially unstable situations, in which a dense fluid overlies a less dense fluid. These situations could produce instabilities that appear as dense plume fingers migrating downwards counteracted by vertical upwards flow of freshwater (Simmons et al., Transp. Porous Medium, 2002). As a result of unstable variable-density flow, solute transport rates are increased over large distances and times as compared to constant-density flow. The numerical simulation of variable-density flow in saturated and unsaturated media requires corresponding benchmark problems against which a computer model is validated (Diersch and Kolditz, Adv. Water Resour, 2002). Recorded data from a laboratory-scale experiment of variable-density flow and solute transport in saturated and unsaturated porous media (Simmons et al., Transp. Porous Medium, 2002) is used to define a new numerical benchmark. The HydroGeoSphere code (Therrien et al., 2004) coupled with PEST (www.pesthomepage.org) are used to obtain an optimized parameter set capable of adequately representing the data set by Simmons et al., (2002). Fingering in the numerical model is triggered using random hydraulic conductivity fields. Due to the inherent randomness, a large number of simulations were conducted in this study. The optimized benchmark model adequately predicts the plume behavior and the fate of solutes. This benchmark is useful for model verification of variable-density flow problems in saturated and/or unsaturated media.

The use of the Hirsch index in benchmarking hepatic surgery research.

PubMed

Cucchetti, Alessandro; Mazzotti, Federico; Pellegrini, Sara; Cescon, Matteo; Maroni, Lorenzo; Ercolani, Giorgio; Pinna, Antonio Daniele

2013-10-01

The Hirsch index (h-index) is recognized as an effective way to summarize an individual's scientific research output. However, a benchmark for evaluating surgeon scientists in the field of hepatic surgery is still not available. A total of 3,251 authors who published between 1949 and 2011 were identified using the Scopus identification number. The h-index, the total number of cited document, the total number of citations, and the scientific age were calculated for each author using both Scopus and Google Scholar. The median h-index was 6 and the median scientific age, assessed with Google Scholar, was 19 years. The numbers of cited documents, numbers of citations, and h-indexes obtained from Scopus and Google Scholar showed good correlation with one another; however, the results from the 2 databases were modified in different ways by scientific age. By plotting scientific age against h-index percentiles an h-index growth chart for both Scopus database and Google Scholar was provided. This analysis provides a first benchmark to assess surgeon scientists' productivity in the field of liver surgery. Copyright © 2013 Elsevier Inc. All rights reserved.

Performance Comparison of HPF and MPI Based NAS Parallel Benchmarks

NASA Technical Reports Server (NTRS)

Saini, Subhash

1997-01-01

Compilers supporting High Performance Form (HPF) features first appeared in late 1994 and early 1995 from Applied Parallel Research (APR), Digital Equipment Corporation, and The Portland Group (PGI). IBM introduced an HPF compiler for the IBM RS/6000 SP2 in April of 1996. Over the past two years, these implementations have shown steady improvement in terms of both features and performance. The performance of various hardware/ programming model (HPF and MPI) combinations will be compared, based on latest NAS Parallel Benchmark results, thus providing a cross-machine and cross-model comparison. Specifically, HPF based NPB results will be compared with MPI based NPB results to provide perspective on performance currently obtainable using HPF versus MPI or versus hand-tuned implementations such as those supplied by the hardware vendors. In addition, we would also present NPB, (Version 1.0) performance results for the following systems: DEC Alpha Server 8400 5/440, Fujitsu CAPP Series (VX, VPP300, and VPP700), HP/Convex Exemplar SPP2000, IBM RS/6000 SP P2SC node (120 MHz), NEC SX-4/32, SGI/CRAY T3E, and SGI Origin2000. We would also present sustained performance per dollar for Class B LU, SP and BT benchmarks.

Estimation of an optimal chemotherapy utilisation rate for cancer: setting an evidence-based benchmark for quality cancer care.

PubMed

Jacob, S A; Ng, W L; Do, V

2015-02-01

There is wide variation in the proportion of newly diagnosed cancer patients who receive chemotherapy, indicating the need for a benchmark rate of chemotherapy utilisation. This study describes an evidence-based model that estimates the proportion of new cancer patients in whom chemotherapy is indicated at least once (defined as the optimal chemotherapy utilisation rate). The optimal chemotherapy utilisation rate can act as a benchmark for measuring and improving the quality of care. Models of optimal chemotherapy utilisation were constructed for each cancer site based on indications for chemotherapy identified from evidence-based treatment guidelines. Data on the proportion of patient- and tumour-related attributes for which chemotherapy was indicated were obtained, using population-based data where possible. Treatment indications and epidemiological data were merged to calculate the optimal chemotherapy utilisation rate. Monte Carlo simulations and sensitivity analyses were used to assess the effect of controversial chemotherapy indications and variations in epidemiological data on our model. Chemotherapy is indicated at least once in 49.1% (95% confidence interval 48.8-49.6%) of all new cancer patients in Australia. The optimal chemotherapy utilisation rates for individual tumour sites ranged from a low of 13% in thyroid cancers to a high of 94% in myeloma. The optimal chemotherapy utilisation rate can serve as a benchmark for planning chemotherapy services on a population basis. The model can be used to evaluate service delivery by comparing the benchmark rate with patterns of care data. The overall estimate for other countries can be obtained by substituting the relevant distribution of cancer types. It can also be used to predict future chemotherapy workload and can be easily modified to take into account future changes in cancer incidence, presentation stage or chemotherapy indications. Copyright © 2014 The Royal College of Radiologists. Published by

HAADF-STEM atom counting in atom probe tomography specimens: Towards quantitative correlative microscopy.

PubMed

Lefebvre, W; Hernandez-Maldonado, D; Moyon, F; Cuvilly, F; Vaudolon, C; Shinde, D; Vurpillot, F

2015-12-01

The geometry of atom probe tomography tips strongly differs from standard scanning transmission electron microscopy foils. Whereas the later are rather flat and thin (<20 nm), tips display a curved surface and a significantly larger thickness. As far as a correlative approach aims at analysing the same specimen by both techniques, it is mandatory to explore the limits and advantages imposed by the particular geometry of atom probe tomography specimens. Based on simulations (electron probe propagation and image simulations), the possibility to apply quantitative high angle annular dark field scanning transmission electron microscopy to of atom probe tomography specimens has been tested. The influence of electron probe convergence and the benefice of deconvolution of electron probe point spread function electron have been established. Atom counting in atom probe tomography specimens is for the first time reported in this present work. It is demonstrated that, based on single projections of high angle annular dark field imaging, significant quantitative information can be used as additional input for refining the data obtained by correlative analysis of the specimen in APT, therefore opening new perspectives in the field of atomic scale tomography. Copyright © 2015 Elsevier B.V. All rights reserved.

Toxicological Benchmarks for Screening Potential Contaminants of Concern for Effects on Terrestrial Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suter, G.W. II

1993-01-01

One of the initial stages in ecological risk assessment for hazardous waste sites is screening contaminants to determine which of them are worthy of further consideration as contaminants of potential concern. This process is termed contaminant screening. It is performed by comparing measured ambient concentrations of chemicals to benchmark concentrations. Currently, no standard benchmark concentrations exist for assessing contaminants in soil with respect to their toxicity to plants. This report presents a standard method for deriving benchmarks for this purpose (phytotoxicity benchmarks), a set of data concerning effects of chemicals in soil or soil solution on plants, and a setmore » of phytotoxicity benchmarks for 38 chemicals potentially associated with United States Department of Energy (DOE) sites. In addition, background information on the phytotoxicity and occurrence of the chemicals in soils is presented, and literature describing the experiments from which data were drawn for benchmark derivation is reviewed. Chemicals that are found in soil at concentrations exceeding both the phytotoxicity benchmark and the background concentration for the soil type should be considered contaminants of potential concern.« less

Parametrization and Benchmark of Long-Range Corrected DFTB2 for Organic Molecules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vuong, Van Quan; Akkarapattiakal Kuriappan, Jissy; Kubillus, Maximilian

In this paper, we present the parametrization and benchmark of long-range corrected second-order density functional tight binding (DFTB), LC-DFTB2, for organic and biological molecules. The LC-DFTB2 model not only improves fundamental orbital energy gaps but also ameliorates the DFT self-interaction error and overpolarization problem, and further improves charge-transfer excited states significantly. Electronic parameters for the construction of the DFTB2 Hamiltonian as well as repulsive potentials were optimized for molecules containing C, H, N, and O chemical elements. We use a semiautomatic parametrization scheme based on a genetic algorithm. With the new parameters, LC-DFTB2 describes geometries and vibrational frequencies of organicmore » molecules similarly well as third-order DFTB3/3OB, the de facto standard parametrization based on a GGA functional. Finally, LC-DFTB2 performs well also for atomization and reaction energies, however, slightly less satisfactorily than DFTB3/3OB.« less

Parametrization and Benchmark of Long-Range Corrected DFTB2 for Organic Molecules

DOE PAGES

Vuong, Van Quan; Akkarapattiakal Kuriappan, Jissy; Kubillus, Maximilian; ...

2017-12-12

In this paper, we present the parametrization and benchmark of long-range corrected second-order density functional tight binding (DFTB), LC-DFTB2, for organic and biological molecules. The LC-DFTB2 model not only improves fundamental orbital energy gaps but also ameliorates the DFT self-interaction error and overpolarization problem, and further improves charge-transfer excited states significantly. Electronic parameters for the construction of the DFTB2 Hamiltonian as well as repulsive potentials were optimized for molecules containing C, H, N, and O chemical elements. We use a semiautomatic parametrization scheme based on a genetic algorithm. With the new parameters, LC-DFTB2 describes geometries and vibrational frequencies of organicmore » molecules similarly well as third-order DFTB3/3OB, the de facto standard parametrization based on a GGA functional. Finally, LC-DFTB2 performs well also for atomization and reaction energies, however, slightly less satisfactorily than DFTB3/3OB.« less

Benchmarking road safety performance: Identifying a meaningful reference (best-in-class).

PubMed

Chen, Faan; Wu, Jiaorong; Chen, Xiaohong; Wang, Jianjun; Wang, Di

2016-01-01

For road safety improvement, comparing and benchmarking performance are widely advocated as the emerging and preferred approaches. However, there is currently no universally agreed upon approach for the process of road safety benchmarking, and performing the practice successfully is by no means easy. This is especially true for the two core activities of which: (1) developing a set of road safety performance indicators (SPIs) and combining them into a composite index; and (2) identifying a meaningful reference (best-in-class), one which has already obtained outstanding road safety practices. To this end, a scientific technique that can combine the multi-dimensional safety performance indicators (SPIs) into an overall index, and subsequently can identify the 'best-in-class' is urgently required. In this paper, the Entropy-embedded RSR (Rank-sum ratio), an innovative, scientific and systematic methodology is investigated with the aim of conducting the above two core tasks in an integrative and concise procedure, more specifically in a 'one-stop' way. Using a combination of results from other methods (e.g. the SUNflower approach) and other measures (e.g. Human Development Index) as a relevant reference, a given set of European countries are robustly ranked and grouped into several classes based on the composite Road Safety Index. Within each class the 'best-in-class' is then identified. By benchmarking road safety performance, the results serve to promote best practice, encourage the adoption of successful road safety strategies and measures and, more importantly, inspire the kind of political leadership needed to create a road transport system that maximizes safety. Copyright © 2015 Elsevier Ltd. All rights reserved.

Toward benchmarking in catalysis science: Best practices, challenges, and opportunities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bligaard, Thomas; Bullock, R. Morris; Campbell, Charles T.

Benchmarking is a community-based and (preferably) community-driven activity involving consensus-based decisions on how to make reproducible, fair, and relevant assessments. In catalysis science, important catalyst performance metrics include activity, selectivity, and the deactivation profile, which enable comparisons between new and standard catalysts. Benchmarking also requires careful documentation, archiving, and sharing of methods and measurements, to ensure that the full value of research data can be realized. Beyond these goals, benchmarking presents unique opportunities to advance and accelerate understanding of complex reaction systems by combining and comparing experimental information from multiple, in situ and operando techniques with theoretical insights derived frommore » calculations characterizing model systems. This Perspective describes the origins and uses of benchmarking and its applications in computational catalysis, heterogeneous catalysis, molecular catalysis, and electrocatalysis. As a result, it also discusses opportunities and challenges for future developments in these fields.« less

Toward benchmarking in catalysis science: Best practices, challenges, and opportunities

DOE PAGES

Bligaard, Thomas; Bullock, R. Morris; Campbell, Charles T.; ...

2016-03-07

Benchmarking is a community-based and (preferably) community-driven activity involving consensus-based decisions on how to make reproducible, fair, and relevant assessments. In catalysis science, important catalyst performance metrics include activity, selectivity, and the deactivation profile, which enable comparisons between new and standard catalysts. Benchmarking also requires careful documentation, archiving, and sharing of methods and measurements, to ensure that the full value of research data can be realized. Beyond these goals, benchmarking presents unique opportunities to advance and accelerate understanding of complex reaction systems by combining and comparing experimental information from multiple, in situ and operando techniques with theoretical insights derived frommore » calculations characterizing model systems. This Perspective describes the origins and uses of benchmarking and its applications in computational catalysis, heterogeneous catalysis, molecular catalysis, and electrocatalysis. As a result, it also discusses opportunities and challenges for future developments in these fields.« less

New Multi-group Transport Neutronics (PHISICS) Capabilities for RELAP5-3D and its Application to Phase I of the OECD/NEA MHTGR-350 MW Benchmark

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gerhard Strydom; Cristian Rabiti; Andrea Alfonsi

2012-10-01

PHISICS is a neutronics code system currently under development at the Idaho National Laboratory (INL). Its goal is to provide state of the art simulation capability to reactor designers. The different modules for PHISICS currently under development are a nodal and semi-structured transport core solver (INSTANT), a depletion module (MRTAU) and a cross section interpolation (MIXER) module. The INSTANT module is the most developed of the mentioned above. Basic functionalities are ready to use, but the code is still in continuous development to extend its capabilities. This paper reports on the effort of coupling the nodal kinetics code package PHISICSmore » (INSTANT/MRTAU/MIXER) to the thermal hydraulics system code RELAP5-3D, to enable full core and system modeling. This will enable the possibility to model coupled (thermal-hydraulics and neutronics) problems with more options for 3D neutron kinetics, compared to the existing diffusion theory neutron kinetics module in RELAP5-3D (NESTLE). In the second part of the paper, an overview of the OECD/NEA MHTGR-350 MW benchmark is given. This benchmark has been approved by the OECD, and is based on the General Atomics 350 MW Modular High Temperature Gas Reactor (MHTGR) design. The benchmark includes coupled neutronics thermal hydraulics exercises that require more capabilities than RELAP5-3D with NESTLE offers. Therefore, the MHTGR benchmark makes extensive use of the new PHISICS/RELAP5-3D coupling capabilities. The paper presents the preliminary results of the three steady state exercises specified in Phase I of the benchmark using PHISICS/RELAP5-3D.« less

Measurements of atomic splittings in atomic hydrogen and the proton charge radius

NASA Astrophysics Data System (ADS)

Hessels, E. A.

2016-09-01

The proton charge radius can be determined from precise measurements of atomic hydrogen spectroscopy. A review of the relevant measurements will be given, including an update on our measurement of the n=2 Lamb shift. The values obtained from hydrogen will be compared to those obtained from muonic hydrogen and from electron-proton elastic scattering measurements. This work is funded by NSERC, CRC and CFI.

Growth mechanism, surface and optical properties of ZnO nanostructures deposited on various Au-seeded thickness obtained by mist-atomization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Afaah, A. N., E-mail: afaahabdullah@yahoo.com; Aadila, A., E-mail: aadilaazizali@gmail.com; Asib, N. A. M., E-mail: amierahasib@yahoo.com

2016-07-06

In this paper, growth mechanisms of ZnO nanostructures on non-seeded glass, 6 nm and 12 nm Au seed layer obtained by mist-atomization was proposed. ZnO films were successfully deposited on glass substrate with different thickness of Au seed layer i.e. 6 nm and 12 nm. The surface and optical properties of the prepared samples were investigated using Field emission scanning electron microscopy (FESEM) and photoluminescence (PL). FESEM micrograph show that ZnO nanostructure deposited on 6 nm Au seed layer has uniform formation and well distributed. From PL spectroscopy, the UV emission shows that ZnO deposited on 6 nm Au seedmore » layer has the more intense UV intensity which proved that high crystal quality of nanostructured ZnO deposited on 6 nm Au seed layer.« less

Benchmarking routine psychological services: a discussion of challenges and methods.

PubMed

Delgadillo, Jaime; McMillan, Dean; Leach, Chris; Lucock, Mike; Gilbody, Simon; Wood, Nick

2014-01-01

Policy developments in recent years have led to important changes in the level of access to evidence-based psychological treatments. Several methods have been used to investigate the effectiveness of these treatments in routine care, with different approaches to outcome definition and data analysis. To present a review of challenges and methods for the evaluation of evidence-based treatments delivered in routine mental healthcare. This is followed by a case example of a benchmarking method applied in primary care. High, average and poor performance benchmarks were calculated through a meta-analysis of published data from services working under the Improving Access to Psychological Therapies (IAPT) Programme in England. Pre-post treatment effect sizes (ES) and confidence intervals were estimated to illustrate a benchmarking method enabling services to evaluate routine clinical outcomes. High, average and poor performance ES for routine IAPT services were estimated to be 0.91, 0.73 and 0.46 for depression (using PHQ-9) and 1.02, 0.78 and 0.52 for anxiety (using GAD-7). Data from one specific IAPT service exemplify how to evaluate and contextualize routine clinical performance against these benchmarks. The main contribution of this report is to summarize key recommendations for the selection of an adequate set of psychometric measures, the operational definition of outcomes, and the statistical evaluation of clinical performance. A benchmarking method is also presented, which may enable a robust evaluation of clinical performance against national benchmarks. Some limitations concerned significant heterogeneity among data sources, and wide variations in ES and data completeness.

Understanding and benchmarking health service achievement of policy goals for chronic disease

PubMed Central

2012-01-01

Background Key challenges in benchmarking health service achievement of policy goals in areas such as chronic disease are: 1) developing indicators and understanding how policy goals might work as indicators of service performance; 2) developing methods for economically collecting and reporting stakeholder perceptions; 3) combining and sharing data about the performance of organizations; 4) interpreting outcome measures; 5) obtaining actionable benchmarking information. This study aimed to explore how a new Boolean-based small-N method from the social sciences—Qualitative Comparative Analysis or QCA—could contribute to meeting these internationally shared challenges. Methods A ‘multi-value QCA’ (MVQCA) analysis was conducted of data from 24 senior staff at 17 randomly selected services for chronic disease, who provided perceptions of 1) whether government health services were improving their achievement of a set of statewide policy goals for chronic disease and 2) the efficacy of state health office actions in influencing this improvement. The analysis produced summaries of configurations of perceived service improvements. Results Most respondents observed improvements in most areas but uniformly good improvements across services were not perceived as happening (regardless of whether respondents identified a state health office contribution to that improvement). The sentinel policy goal of using evidence to develop service practice was not achieved at all in four services and appears to be reliant on other kinds of service improvements happening. Conclusions The QCA method suggested theoretically plausible findings and an approach that with further development could help meet the five benchmarking challenges. In particular, it suggests that achievement of one policy goal may be reliant on achievement of another goal in complex ways that the literature has not yet fully accommodated but which could help prioritize policy goals. The weaknesses of QCA can be

Benchmarking of Neutron Flux Parameters at the USGS TRIGA Reactor in Lakewood, Colorado

NASA Astrophysics Data System (ADS)

Alzaabi, Osama E.

The USGS TRIGA Reactor (GSTR) located at the Denver Federal Center in Lakewood Colorado provides opportunities to Colorado School of Mines students to do experimental research in the field of neutron activation analysis. The scope of this thesis is to obtain precise knowledge of neutron flux parameters at the GSTR. The Colorado School of Mines Nuclear Physics group intends to develop several research projects at the GSTR, which requires the precise knowledge of neutron fluxes and energy distributions in several irradiation locations. The fuel burn-up of the new GSTR fuel configuration and the thermal neutron flux of the core were recalculated since the GSTR core configuration had been changed with the addition of two new fuel elements. Therefore, a MCNP software package was used to incorporate the burn up of reactor fuel and to determine the neutron flux at different irradiation locations and at flux monitoring bores. These simulation results were compared with neutron activation analysis results using activated diluted gold wires. A well calibrated and stable germanium detector setup as well as fourteen samplers were designed and built to achieve accuracy in the measurement of the neutron flux. Furthermore, the flux monitoring bores of the GSTR core were used for the first time to measure neutron flux experimentally and to compare to MCNP simulation. In addition, International Atomic Energy Agency (IAEA) standard materials were used along with USGS national standard materials in a previously well calibrated irradiation location to benchmark simulation, germanium detector calibration and sample measurements to international standards.

Fully methylated, atomically flat (111) silicon surface

NASA Astrophysics Data System (ADS)

Fidélis, A.; Ozanam, F.; Chazalviel, J.-N.

2000-01-01

The atomically flat hydrogenated (111) silicon surface has been methylated by anodization in a Grignard reagent and the surface obtained characterized by infrared spectroscopy. 100% substitution of the hydrogen atoms by methyl groups is observed. The resulting surface exhibits preserved ordering and superior chemical stability.

Benchmarking Ada tasking on tightly coupled multiprocessor architectures

NASA Technical Reports Server (NTRS)

Collard, Philippe; Goforth, Andre; Marquardt, Matthew

1989-01-01

The development of benchmarks and performance measures for parallel Ada tasking is reported with emphasis on the macroscopic behavior of the benchmark across a set of load parameters. The application chosen for the study was the NASREM model for telerobot control, relevant to many NASA missions. The results of the study demonstrate the potential of parallel Ada in accomplishing the task of developing a control system for a system such as the Flight Telerobotic Servicer using the NASREM framework.

Knowledge Extraction from Atomically Resolved Images.

PubMed

Vlcek, Lukas; Maksov, Artem; Pan, Minghu; Vasudevan, Rama K; Kalinin, Sergei V

2017-10-24

Tremendous strides in experimental capabilities of scanning transmission electron microscopy and scanning tunneling microscopy (STM) over the past 30 years made atomically resolved imaging routine. However, consistent integration and use of atomically resolved data with generative models is unavailable, so information on local thermodynamics and other microscopic driving forces encoded in the observed atomic configurations remains hidden. Here, we present a framework based on statistical distance minimization to consistently utilize the information available from atomic configurations obtained from an atomically resolved image and extract meaningful physical interaction parameters. We illustrate the applicability of the framework on an STM image of a FeSe x Te 1-x superconductor, with the segregation of the chalcogen atoms investigated using a nonideal interacting solid solution model. This universal method makes full use of the microscopic degrees of freedom sampled in an atomically resolved image and can be extended via Bayesian inference toward unbiased model selection with uncertainty quantification.

Marking Closely or on the Bench?: An Australian's Benchmark Statement.

ERIC Educational Resources Information Center

Jones, Roy

2000-01-01

Reviews the benchmark statements of the Quality Assurance Agency for Higher Education in the United Kingdom. Examines the various sections within the benchmark. States that in terms of emphasizing the positive attributes of the geography discipline the statements have wide utility and applicability. (CMK)

40 CFR 141.543 - How is the disinfection benchmark calculated?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Disinfection Benchmark § 141.543 How is the disinfection... 40 Protection of Environment 22 2010-07-01 2010-07-01 false How is the disinfection benchmark...

40 CFR 141.709 - Developing the disinfection profile and benchmark.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 23 2011-07-01 2011-07-01 false Developing the disinfection profile... Cryptosporidium Disinfection Profiling and Benchmarking Requirements § 141.709 Developing the disinfection profile and benchmark. (a) Systems required to develop disinfection profiles under § 141.708 must follow the...

40 CFR 141.709 - Developing the disinfection profile and benchmark.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Developing the disinfection profile... Cryptosporidium Disinfection Profiling and Benchmarking Requirements § 141.709 Developing the disinfection profile and benchmark. (a) Systems required to develop disinfection profiles under § 141.708 must follow the...

40 CFR 141.709 - Developing the disinfection profile and benchmark.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Developing the disinfection profile... Cryptosporidium Disinfection Profiling and Benchmarking Requirements § 141.709 Developing the disinfection profile and benchmark. (a) Systems required to develop disinfection profiles under § 141.708 must follow the...

40 CFR 141.709 - Developing the disinfection profile and benchmark.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 24 2013-07-01 2013-07-01 false Developing the disinfection profile... Cryptosporidium Disinfection Profiling and Benchmarking Requirements § 141.709 Developing the disinfection profile and benchmark. (a) Systems required to develop disinfection profiles under § 141.708 must follow the...

Rethinking the reference collection: exploring benchmarks and e-book availability.

PubMed

Husted, Jeffrey T; Czechowski, Leslie J

2012-01-01

Librarians in the Health Sciences Library System at the University of Pittsburgh explored the possibility of developing an electronic reference collection that would replace the print reference collection, thus providing access to these valuable materials to a widely dispersed user population. The librarians evaluated the print reference collection and standard collection development lists as potential benchmarks for the electronic collection, and they determined which books were available in electronic format. They decided that the low availability of electronic versions of titles in each benchmark group rendered the creation of an electronic reference collection using either benchmark impractical.

An automated protocol for performance benchmarking a widefield fluorescence microscope.

PubMed

Halter, Michael; Bier, Elianna; DeRose, Paul C; Cooksey, Gregory A; Choquette, Steven J; Plant, Anne L; Elliott, John T

2014-11-01

Widefield fluorescence microscopy is a highly used tool for visually assessing biological samples and for quantifying cell responses. Despite its widespread use in high content analysis and other imaging applications, few published methods exist for evaluating and benchmarking the analytical performance of a microscope. Easy-to-use benchmarking methods would facilitate the use of fluorescence imaging as a quantitative analytical tool in research applications, and would aid the determination of instrumental method validation for commercial product development applications. We describe and evaluate an automated method to characterize a fluorescence imaging system's performance by benchmarking the detection threshold, saturation, and linear dynamic range to a reference material. The benchmarking procedure is demonstrated using two different materials as the reference material, uranyl-ion-doped glass and Schott 475 GG filter glass. Both are suitable candidate reference materials that are homogeneously fluorescent and highly photostable, and the Schott 475 GG filter glass is currently commercially available. In addition to benchmarking the analytical performance, we also demonstrate that the reference materials provide for accurate day to day intensity calibration. Published 2014 Wiley Periodicals Inc. Published 2014 Wiley Periodicals Inc. This article is a US government work and, as such, is in the public domain in the United States of America.

Magnetism of a relaxed single atom vacancy in graphene

NASA Astrophysics Data System (ADS)

Wu, Yunyi; Hu, Yonghong; Xue, Li; Sun, Tieyu; Wang, Yu

2018-04-01

It has been suggested in literature that defects in graphene (e.g. absorbed atoms and vacancies) may induce magnetizations due to unpaired electrons. The nature of magnetism, i.e. ferromagnetic or anti-ferromagnetic, is dependent on a number of structural factors including locations of magnetic moments and lattice symmetry. In the present work we investigated the influence of a relaxed single atom vacancy in garphnene on magnetization which were obtained under different pinning boundary conditions, aiming to achieve a better understanding of the magnetic behaviors of graphene. Through first principles calculations, we found that major spin polarizations occur on atoms that deviate slightly from their original lattice positions, and pinning boundaries could also affect the relaxed positions of atoms and determine which atom(s) would become the main source(s) of total spin polarizations and magnetic moments. When the pinning boundary condition is free, a special non-magnetic and semi-conductive structure may be obtained, suggesting that magnetization should more readily occur under pinning boundary conditions.

Toxicological benchmarks for screening potential contaminants of concern for effects on aquatic biota: 1994 Revision

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suter, G.W. II; Mabrey, J.B.

1994-07-01

This report presents potential screening benchmarks for protection of aquatic life from contaminants in water. Because there is no guidance for screening benchmarks, a set of alternative benchmarks is presented herein. The alternative benchmarks are based on different conceptual approaches to estimating concentrations causing significant effects. For the upper screening benchmark, there are the acute National Ambient Water Quality Criteria (NAWQC) and the Secondary Acute Values (SAV). The SAV concentrations are values estimated with 80% confidence not to exceed the unknown acute NAWQC for those chemicals with no NAWQC. The alternative chronic benchmarks are the chronic NAWQC, the Secondary Chronicmore » Value (SCV), the lowest chronic values for fish and daphnids from chronic toxicity tests, the estimated EC20 for a sensitive species, and the concentration estimated to cause a 20% reduction in the recruit abundance of largemouth bass. It is recommended that ambient chemical concentrations be compared to all of these benchmarks. If NAWQC are exceeded, the chemicals must be contaminants of concern because the NAWQC are applicable or relevant and appropriate requirements (ARARs). If NAWQC are not exceeded, but other benchmarks are, contaminants should be selected on the basis of the number of benchmarks exceeded and the conservatism of the particular benchmark values, as discussed in the text. To the extent that toxicity data are available, this report presents the alternative benchmarks for chemicals that have been detected on the Oak Ridge Reservation. It also presents the data used to calculate benchmarks and the sources of the data. It compares the benchmarks and discusses their relative conservatism and utility.« less

Finite Element Modeling of the World Federation's Second MFL Benchmark Problem

NASA Astrophysics Data System (ADS)

Zeng, Zhiwei; Tian, Yong; Udpa, Satish; Udpa, Lalita

2004-02-01

This paper presents results obtained by simulating the second magnetic flux leakage benchmark problem proposed by the World Federation of NDE Centers. The geometry consists of notches machined on the internal and external surfaces of a rotating steel pipe that is placed between two yokes that are part of a magnetic circuit energized by an electromagnet. The model calculates the radial component of the leaked field at specific positions. The nonlinear material property of the ferromagnetic pipe is taken into account in simulating the problem. The velocity effect caused by the rotation of the pipe is, however, ignored for reasons of simplicity.

The application of quasi-steady approximation in atomic kinetics in simulation of hohlraum radiation drive

NASA Astrophysics Data System (ADS)

Ren, Guoli; Pei, Wenbing; Lan, Ke; Li, Xin; Hohlraum Physics Team

2014-10-01

In current routine 2D simulation of hohlraum physics, we adopt the principal-quantum-number (n-level) average atom model (AAM) in NLTE plasma description. The more sophisticated atomic kinetics description is better choice, but the in-line calculation consumes much more resource. By distinguishing the much more fast bound-bound atomic processes from the relative slow bound-free atomic processes, we found a method to built up a bound electron distribution (n-level or nl-level) using in-line n-level calculated plasma condition (such as temperature, density, average ionization degree). We name this method ``quasi-steady approximation.'' Using this method and the plasma condition calculated under n-level, we re-build the nl-level bound electron distribution (Pnl), and acquire a new hohlraum radiative drive by post-processing. Comparison with the n-level post-processed hohlraum drive shows that we get an almost identical radiation flux but with more-detailed frequency-dependant structures. Also we use this method in the benchmark gold sphere experiment, the constructed nl-level radiation drive resembles the experimental results and DCA results, while the n-level raditation does not.

Determination of the line shapes of atomic nitrogen resonance lines by magnetic scans

NASA Technical Reports Server (NTRS)

Lawrence, G. M.; Stone, E. J.; Kley, D.

1976-01-01

A technique is given for calibrating an atomic nitrogen resonance lamp for use in determining column densities of atoms in specific states. A discharge lamp emitting the NI multiplets at 1200 A and 1493 A is studied by obtaining absorption by atoms in a magnetic field (0-2.5 T). This magnetic scanning technique enables the determination of the absorbing atom column density, and an empirical curve of growth is obtained because the atomic f-value is known. Thus, the calibrated lamp can be used in the determination of atomic column densities.

How to Use Benchmark and Cross-section Studies to Improve Data Libraries and Models

NASA Astrophysics Data System (ADS)

Wagner, V.; Suchopár, M.; Vrzalová, J.; Chudoba, P.; Svoboda, O.; Tichý, P.; Krása, A.; Majerle, M.; Kugler, A.; Adam, J.; Baldin, A.; Furman, W.; Kadykov, M.; Solnyshkin, A.; Tsoupko-Sitnikov, S.; Tyutyunikov, S.; Vladimirovna, N.; Závorka, L.

2016-06-01

Improvements of the Monte Carlo transport codes and cross-section libraries are very important steps towards usage of the accelerator-driven transmutation systems. We have conducted a lot of benchmark experiments with different set-ups consisting of lead, natural uranium and moderator irradiated by relativistic protons and deuterons within framework of the collaboration “Energy and Transmutation of Radioactive Waste”. Unfortunately, the knowledge of the total or partial cross-sections of important reactions is insufficient. Due to this reason we have started extensive studies of different reaction cross-sections. We measure cross-sections of important neutron reactions by means of the quasi-monoenergetic neutron sources based on the cyclotrons at Nuclear Physics Institute in Řež and at The Svedberg Laboratory in Uppsala. Measurements of partial cross-sections of relativistic deuteron reactions were the second direction of our studies. The new results obtained during last years will be shown. Possible use of these data for improvement of libraries, models and benchmark studies will be discussed.

Testing New Programming Paradigms with NAS Parallel Benchmarks

NASA Technical Reports Server (NTRS)

Jin, H.; Frumkin, M.; Schultz, M.; Yan, J.

2000-01-01

was applied to several benchmarks, noticeably BT and SP, resulting in better sequential performance. In order to overcome the lack of an HPF performance model and guide the development of the HPF codes, we employed an empirical performance model for several primitives found in the benchmarks. We encountered a few limitations of HPF, such as lack of supporting the "REDISTRIBUTION" directive and no easy way to handle irregular computation. The parallelization with OpenMP directives was done at the outer-most loop level to achieve the largest granularity. The performance of six HPF and OpenMP benchmarks is compared with their MPI counterparts for the Class-A problem size in the figure in next page. These results were obtained on an SGI Origin2000 (195MHz) with MIPSpro-f77 compiler 7.2.1 for OpenMP and MPI codes and PGI pghpf-2.4.3 compiler with MPI interface for HPF programs.

The art and science of using routine outcome measurement in mental health benchmarking.

PubMed

McKay, Roderick; Coombs, Tim; Duerden, David

2014-02-01

To report and critique the application of routine outcome measurement data when benchmarking Australian mental health services. The experience of the authors as participants and facilitators of benchmarking activities is augmented by a review of the literature regarding mental health benchmarking in Australia. Although the published literature is limited, in practice, routine outcome measures, in particular the Health of the National Outcomes Scales (HoNOS) family of measures, are used in a variety of benchmarking activities. Use in exploring similarities and differences in consumers between services and the outcomes of care are illustrated. This requires the rigour of science in data management and interpretation, supplemented by the art that comes from clinical experience, a desire to reflect on clinical practice and the flexibility to use incomplete data to explore clinical practice. Routine outcome measurement data can be used in a variety of ways to support mental health benchmarking. With the increasing sophistication of information development in mental health, the opportunity to become involved in benchmarking will continue to increase. The techniques used during benchmarking and the insights gathered may prove useful to support reflection on practice by psychiatrists and other senior mental health clinicians.

Benchmarking facilities providing care: An international overview of initiatives

PubMed Central

Thonon, Frédérique; Watson, Jonathan; Saghatchian, Mahasti

2015-01-01

We performed a literature review of existing benchmarking projects of health facilities to explore (1) the rationales for those projects, (2) the motivation for health facilities to participate, (3) the indicators used and (4) the success and threat factors linked to those projects. We studied both peer-reviewed and grey literature. We examined 23 benchmarking projects of different medical specialities. The majority of projects used a mix of structure, process and outcome indicators. For some projects, participants had a direct or indirect financial incentive to participate (such as reimbursement by Medicaid/Medicare or litigation costs related to quality of care). A positive impact was reported for most projects, mainly in terms of improvement of practice and adoption of guidelines and, to a lesser extent, improvement in communication. Only 1 project reported positive impact in terms of clinical outcomes. Success factors and threats are linked to both the benchmarking process (such as organisation of meetings, link with existing projects) and indicators used (such as adjustment for diagnostic-related groups). The results of this review will help coordinators of a benchmarking project to set it up successfully. PMID:26770800

Measurement, Standards, and Peer Benchmarking: One Hospital's Journey.

PubMed

Martin, Brian S; Arbore, Mark

2016-04-01

Peer-to-peer benchmarking is an important component of rapid-cycle performance improvement in patient safety and quality-improvement efforts. Institutions should carefully examine critical success factors before engagement in peer-to-peer benchmarking in order to maximize growth and change opportunities. Solutions for Patient Safety has proven to be a high-yield engagement for Children's Hospital of Pittsburgh of University of Pittsburgh Medical Center, with measureable improvement in both organizational process and culture. Copyright © 2016 Elsevier Inc. All rights reserved.

Benchmark Problems Used to Assess Computational Aeroacoustics Codes

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Envia, Edmane

2005-01-01

The field of computational aeroacoustics (CAA) encompasses numerical techniques for calculating all aspects of sound generation and propagation in air directly from fundamental governing equations. Aeroacoustic problems typically involve flow-generated noise, with and without the presence of a solid surface, and the propagation of the sound to a receiver far away from the noise source. It is a challenge to obtain accurate numerical solutions to these problems. The NASA Glenn Research Center has been at the forefront in developing and promoting the development of CAA techniques and methodologies for computing the noise generated by aircraft propulsion systems. To assess the technological advancement of CAA, Glenn, in cooperation with the Ohio Aerospace Institute and the AeroAcoustics Research Consortium, organized and hosted the Fourth CAA Workshop on Benchmark Problems. Participants from industry and academia from both the United States and abroad joined to present and discuss solutions to benchmark problems. These demonstrated technical progress ranging from the basic challenges to accurate CAA calculations to the solution of CAA problems of increasing complexity and difficulty. The results are documented in the proceedings of the workshop. Problems were solved in five categories. In three of the five categories, exact solutions were available for comparison with CAA results. A fourth category of problems representing sound generation from either a single airfoil or a blade row interacting with a gust (i.e., problems relevant to fan noise) had approximate analytical or completely numerical solutions. The fifth category of problems involved sound generation in a viscous flow. In this case, the CAA results were compared with experimental data.

COMPETITIVE BIDDING IN MEDICARE ADVANTAGE: EFFECT OF BENCHMARK CHANGES ON PLAN BIDS

PubMed Central

Song, Zirui; Landrum, Mary Beth; Chernew, Michael E.

2013-01-01

Bidding has been proposed to replace or complement the administered prices in Medicare pays to hospitals and health plans. In 2006, the Medicare Advantage program implemented a competitive bidding system to determine plan payments. In perfectly competitive models, plans bid their costs and thus bids are insensitive to the benchmark. Under many other models of competition, bids respond to changes in the benchmark. We conceptualize the bidding system and use an instrumental variable approach to study the effect of benchmark changes on bids. We use 2006–2010 plan payment data from the Centers for Medicare and Medicaid Services, published county benchmarks, actual realized fee-for-service costs, and Medicare Advantage enrollment. We find that a $1 increase in the benchmark leads to about a $0.53 increase in bids, suggesting that plans in the Medicare Advantage market have meaningful market power. PMID:24308881

Competitive bidding in Medicare Advantage: effect of benchmark changes on plan bids.

PubMed

Song, Zirui; Landrum, Mary Beth; Chernew, Michael E

2013-12-01

Bidding has been proposed to replace or complement the administered prices that Medicare pays to hospitals and health plans. In 2006, the Medicare Advantage program implemented a competitive bidding system to determine plan payments. In perfectly competitive models, plans bid their costs and thus bids are insensitive to the benchmark. Under many other models of competition, bids respond to changes in the benchmark. We conceptualize the bidding system and use an instrumental variable approach to study the effect of benchmark changes on bids. We use 2006-2010 plan payment data from the Centers for Medicare and Medicaid Services, published county benchmarks, actual realized fee-for-service costs, and Medicare Advantage enrollment. We find that a $1 increase in the benchmark leads to about a $0.53 increase in bids, suggesting that plans in the Medicare Advantage market have meaningful market power. Copyright © 2013 Elsevier B.V. All rights reserved.

How do I know if my forecasts are better? Using benchmarks in hydrological ensemble prediction

NASA Astrophysics Data System (ADS)

Pappenberger, F.; Ramos, M. H.; Cloke, H. L.; Wetterhall, F.; Alfieri, L.; Bogner, K.; Mueller, A.; Salamon, P.

2015-03-01

The skill of a forecast can be assessed by comparing the relative proximity of both the forecast and a benchmark to the observations. Example benchmarks include climatology or a naïve forecast. Hydrological ensemble prediction systems (HEPS) are currently transforming the hydrological forecasting environment but in this new field there is little information to guide researchers and operational forecasters on how benchmarks can be best used to evaluate their probabilistic forecasts. In this study, it is identified that the forecast skill calculated can vary depending on the benchmark selected and that the selection of a benchmark for determining forecasting system skill is sensitive to a number of hydrological and system factors. A benchmark intercomparison experiment is then undertaken using the continuous ranked probability score (CRPS), a reference forecasting system and a suite of 23 different methods to derive benchmarks. The benchmarks are assessed within the operational set-up of the European Flood Awareness System (EFAS) to determine those that are 'toughest to beat' and so give the most robust discrimination of forecast skill, particularly for the spatial average fields that EFAS relies upon. Evaluating against an observed discharge proxy the benchmark that has most utility for EFAS and avoids the most naïve skill across different hydrological situations is found to be meteorological persistency. This benchmark uses the latest meteorological observations of precipitation and temperature to drive the hydrological model. Hydrological long term average benchmarks, which are currently used in EFAS, are very easily beaten by the forecasting system and the use of these produces much naïve skill. When decomposed into seasons, the advanced meteorological benchmarks, which make use of meteorological observations from the past 20 years at the same calendar date, have the most skill discrimination. They are also good at discriminating skill in low flows and for all

Using Institutional Survey Data to Jump-Start Your Benchmarking Process

ERIC Educational Resources Information Center

Chow, Timothy K. C.

2012-01-01

Guided by the missions and visions, higher education institutions utilize benchmarking processes to identify better and more efficient ways to carry out their operations. Aside from the initial planning and organization steps involved in benchmarking, a matching or selection step is crucial for identifying other institutions that have good…

Practical Considerations when Using Benchmarking for Accountability in Higher Education

ERIC Educational Resources Information Center

Achtemeier, Sue D.; Simpson, Ronald D.

2005-01-01

The qualitative study on which this article is based examined key individuals' perceptions, both within a research university community and beyond in its external governing board, of how to improve benchmarking as an accountability method in higher education. Differing understanding of benchmarking revealed practical implications for using it as…

Benchmarking in pathology: development of an activity-based costing model.

PubMed

Burnett, Leslie; Wilson, Roger; Pfeffer, Sally; Lowry, John

2012-12-01

Benchmarking in Pathology (BiP) allows pathology laboratories to determine the unit cost of all laboratory tests and procedures, and also provides organisational productivity indices allowing comparisons of performance with other BiP participants. We describe 14 years of progressive enhancement to a BiP program, including the implementation of 'avoidable costs' as the accounting basis for allocation of costs rather than previous approaches using 'total costs'. A hierarchical tree-structured activity-based costing model distributes 'avoidable costs' attributable to the pathology activities component of a pathology laboratory operation. The hierarchical tree model permits costs to be allocated across multiple laboratory sites and organisational structures. This has enabled benchmarking on a number of levels, including test profiles and non-testing related workload activities. The development of methods for dealing with variable cost inputs, allocation of indirect costs using imputation techniques, panels of tests, and blood-bank record keeping, have been successfully integrated into the costing model. A variety of laboratory management reports are produced, including the 'cost per test' of each pathology 'test' output. Benchmarking comparisons may be undertaken at any and all of the 'cost per test' and 'cost per Benchmarking Complexity Unit' level, 'discipline/department' (sub-specialty) level, or overall laboratory/site and organisational levels. We have completed development of a national BiP program. An activity-based costing methodology based on avoidable costs overcomes many problems of previous benchmarking studies based on total costs. The use of benchmarking complexity adjustment permits correction for varying test-mix and diagnostic complexity between laboratories. Use of iterative communication strategies with program participants can overcome many obstacles and lead to innovations.

A call for benchmarking transposable element annotation methods.

PubMed

Hoen, Douglas R; Hickey, Glenn; Bourque, Guillaume; Casacuberta, Josep; Cordaux, Richard; Feschotte, Cédric; Fiston-Lavier, Anna-Sophie; Hua-Van, Aurélie; Hubley, Robert; Kapusta, Aurélie; Lerat, Emmanuelle; Maumus, Florian; Pollock, David D; Quesneville, Hadi; Smit, Arian; Wheeler, Travis J; Bureau, Thomas E; Blanchette, Mathieu

2015-01-01

DNA derived from transposable elements (TEs) constitutes large parts of the genomes of complex eukaryotes, with major impacts not only on genomic research but also on how organisms evolve and function. Although a variety of methods and tools have been developed to detect and annotate TEs, there are as yet no standard benchmarks-that is, no standard way to measure or compare their accuracy. This lack of accuracy assessment calls into question conclusions from a wide range of research that depends explicitly or implicitly on TE annotation. In the absence of standard benchmarks, toolmakers are impeded in improving their tools, annotators cannot properly assess which tools might best suit their needs, and downstream researchers cannot judge how accuracy limitations might impact their studies. We therefore propose that the TE research community create and adopt standard TE annotation benchmarks, and we call for other researchers to join the authors in making this long-overdue effort a success.

Interactive visual optimization and analysis for RFID benchmarking.

PubMed

Wu, Yingcai; Chung, Ka-Kei; Qu, Huamin; Yuan, Xiaoru; Cheung, S C

2009-01-01

Radio frequency identification (RFID) is a powerful automatic remote identification technique that has wide applications. To facilitate RFID deployment, an RFID benchmarking instrument called aGate has been invented to identify the strengths and weaknesses of different RFID technologies in various environments. However, the data acquired by aGate are usually complex time varying multidimensional 3D volumetric data, which are extremely challenging for engineers to analyze. In this paper, we introduce a set of visualization techniques, namely, parallel coordinate plots, orientation plots, a visual history mechanism, and a 3D spatial viewer, to help RFID engineers analyze benchmark data visually and intuitively. With the techniques, we further introduce two workflow procedures (a visual optimization procedure for finding the optimum reader antenna configuration and a visual analysis procedure for comparing the performance and identifying the flaws of RFID devices) for the RFID benchmarking, with focus on the performance analysis of the aGate system. The usefulness and usability of the system are demonstrated in the user evaluation.

Observing random walks of atoms in buffer gas through resonant light absorption

NASA Astrophysics Data System (ADS)

Aoki, Kenichiro; Mitsui, Takahisa

2016-07-01

Using resonant light absorption, random-walk motions of rubidium atoms in nitrogen buffer gas are observed directly. The transmitted light intensity through atomic vapor is measured, and its spectrum is obtained, down to orders of magnitude below the shot-noise level to detect fluctuations caused by atomic motions. To understand the measured spectra, the spectrum for atoms performing random walks in a Gaussian light beam is computed, and its analytical form is obtained. The spectrum has 1 /f2 (f is frequency) behavior at higher frequencies, crossing over to a different, but well-defined, behavior at lower frequencies. The properties of this theoretical spectrum agree excellently with the measured spectrum. This understanding also enables us to obtain the diffusion constant, the photon cross section of atoms in buffer gas, and the atomic number density from a single spectral measurement. We further discuss other possible applications of our experimental method and analysis.

Measuring How Benchmark Assessments Affect Student Achievement. Issues & Answers. REL 2007-No. 039

ERIC Educational Resources Information Center

Henderson, Susan; Petrosino, Anthony; Guckenburg, Sarah; Hamilton, Stephen

2007-01-01

This report examines a Massachusetts pilot program for quarterly benchmark exams in middle-school mathematics, finding that program schools do not show greater gains in student achievement after a year. But that finding might reflect limited data rather than ineffective benchmark assessments. Benchmark assessments are used in many districts…

GPI Spectroscopy of the Mass, Age, and Metallicity Benchmark Brown Dwarf HD 4747 B

NASA Astrophysics Data System (ADS)

Crepp, Justin R.; Principe, David A.; Wolff, Schuyler; Giorla Godfrey, Paige A.; Rice, Emily L.; Cieza, Lucas; Pueyo, Laurent; Bechter, Eric B.; Gonzales, Erica J.

2018-02-01

The physical properties of brown dwarf companions found to orbit nearby, solar-type stars can be benchmarked against independent measures of their mass, age, chemical composition, and other parameters, offering insights into the evolution of substellar objects. The TRENDS high-contrast imaging survey has recently discovered a (mass/age/metallicity) benchmark brown dwarf orbiting the nearby (d = 18.69 ± 0.19 pc), G8V/K0V star HD 4747. We have acquired follow-up spectroscopic measurements of HD 4747 B using the Gemini Planet Imager to study its spectral type, effective temperature, surface gravity, and cloud properties. Observations obtained in the H-band and K 1-band recover the companion and reveal that it is near the L/T transition (T1 ± 2). Fitting atmospheric models to the companion spectrum, we find strong evidence for the presence of clouds. However, spectral models cannot satisfactorily fit the complete data set: while the shape of the spectrum can be well-matched in individual filters, a joint fit across the full passband results in discrepancies that are a consequence of the inherent color of the brown dwarf. We also find a 2σ tension in the companion mass, age, and surface gravity when comparing to evolutionary models. These results highlight the importance of using benchmark objects to study “secondary effects” such as metallicity, non-equilibrium chemistry, cloud parameters, electron conduction, non-adiabatic cooling, and other subtleties affecting emergent spectra. As a new L/T transition benchmark, HD 4747 B warrants further investigation into the modeling of cloud physics using higher resolution spectroscopy across a broader range of wavelengths, polarimetric observations, and continued Doppler radial velocity and astrometric monitoring.

Ultracool dwarf benchmarks with Gaia primaries

NASA Astrophysics Data System (ADS)

Marocco, F.; Pinfield, D. J.; Cook, N. J.; Zapatero Osorio, M. R.; Montes, D.; Caballero, J. A.; Gálvez-Ortiz, M. C.; Gromadzki, M.; Jones, H. R. A.; Kurtev, R.; Smart, R. L.; Zhang, Z.; Cabrera Lavers, A. L.; García Álvarez, D.; Qi, Z. X.; Rickard, M. J.; Dover, L.

2017-10-01

We explore the potential of Gaia for the field of benchmark ultracool/brown dwarf companions, and present the results of an initial search for metal-rich/metal-poor systems. A simulated population of resolved ultracool dwarf companions to Gaia primary stars is generated and assessed. Of the order of ˜24 000 companions should be identifiable outside of the Galactic plane (|b| > 10 deg) with large-scale ground- and space-based surveys including late M, L, T and Y types. Our simulated companion parameter space covers 0.02 ≤ M/M⊙ ≤ 0.1, 0.1 ≤ age/Gyr ≤ 14 and -2.5 ≤ [Fe/H] ≤ 0.5, with systems required to have a false alarm probability <10-4, based on projected separation and expected constraints on common distance, common proper motion and/or common radial velocity. Within this bulk population, we identify smaller target subsets of rarer systems whose collective properties still span the full parameter space of the population, as well as systems containing primary stars that are good age calibrators. Our simulation analysis leads to a series of recommendations for candidate selection and observational follow-up that could identify ˜500 diverse Gaia benchmarks. As a test of the veracity of our methodology and simulations, our initial search uses UKIRT Infrared Deep Sky Survey and Sloan Digital Sky Survey to select secondaries, with the parameters of primaries taken from Tycho-2, Radial Velocity Experiment, Large sky Area Multi-Object fibre Spectroscopic Telescope and Tycho-Gaia Astrometric Solution. We identify and follow up 13 new benchmarks. These include M8-L2 companions, with metallicity constraints ranging in quality, but robust in the range -0.39 ≤ [Fe/H] ≤ +0.36, and with projected physical separation in the range 0.6 < s/kau < 76. Going forward, Gaia offers a very high yield of benchmark systems, from which diverse subsamples may be able to calibrate a range of foundational ultracool/sub-stellar theory and observation.

Learning Through Benchmarking: Developing a Relational, Prospective Approach to Benchmarking ICT in Learning and Teaching

ERIC Educational Resources Information Center

Ellis, Robert A.; Moore, Roger R.

2006-01-01

This study discusses benchmarking the use of information and communication technologies (ICT) in teaching and learning between two universities with different missions: one an Australian campus-based metropolitan university and the other a British distance-education provider. It argues that the differences notwithstanding, it is possible to…

Benchmarking high performance computing architectures with CMS’ skeleton framework

NASA Astrophysics Data System (ADS)

Sexton-Kennedy, E.; Gartung, P.; Jones, C. D.

2017-10-01

In 2012 CMS evaluated which underlying concurrency technology would be the best to use for its multi-threaded framework. The available technologies were evaluated on the high throughput computing systems dominating the resources in use at that time. A skeleton framework benchmarking suite that emulates the tasks performed within a CMSSW application was used to select Intel’s Thread Building Block library, based on the measured overheads in both memory and CPU on the different technologies benchmarked. In 2016 CMS will get access to high performance computing resources that use new many core architectures; machines such as Cori Phase 1&2, Theta, Mira. Because of this we have revived the 2012 benchmark to test it’s performance and conclusions on these new architectures. This talk will discuss the results of this exercise.

Atomization and Mixing Study

NASA Technical Reports Server (NTRS)

Ferrenberg, A.; Hunt, K.; Duesberg, J.

1985-01-01

The primary objective was the obtainment of atomization and mixing performance data for a variety of typical liquid oxygen/hydrocarbon injector element designs. Such data are required to establish injector design criteria and to provide critical inputs to liquid rocket engine combustor performance and stability analysis, and computational codes and methods. Deficiencies and problems with the atomization test equipment were identified, and action initiated to resolve them. Test results of the gas/liquid mixing tests indicated that an assessment of test methods was required. A series of 71 liquid/liquid tests were performed.

Benchmarking: measuring the outcomes of evidence-based practice.

PubMed

DeLise, D C; Leasure, A R

2001-01-01

Measurement of the outcomes associated with implementation of evidence-based practice changes is becoming increasingly emphasized by multiple health care disciplines. A final step to the process of implementing and sustaining evidence-supported practice changes is that of outcomes evaluation and monitoring. The comparison of outcomes to internal and external measures is known as benchmarking. This article discusses evidence-based practice, provides an overview of outcomes evaluation, and describes the process of benchmarking to improve practice. A case study is used to illustrate this concept.

Experimental Mapping and Benchmarking of Magnetic Field Codes on the LHD Ion Accelerator

NASA Astrophysics Data System (ADS)

Chitarin, G.; Agostinetti, P.; Gallo, A.; Marconato, N.; Nakano, H.; Serianni, G.; Takeiri, Y.; Tsumori, K.

2011-09-01

For the validation of the numerical models used for the design of the Neutral Beam Test Facility for ITER in Padua [1], an experimental benchmark against a full-size device has been sought. The LHD BL2 injector [2] has been chosen as a first benchmark, because the BL2 Negative Ion Source and Beam Accelerator are geometrically similar to SPIDER, even though BL2 does not include current bars and ferromagnetic materials. A comprehensive 3D magnetic field model of the LHD BL2 device has been developed based on the same assumptions used for SPIDER. In parallel, a detailed experimental magnetic map of the BL2 device has been obtained using a suitably designed 3D adjustable structure for the fine positioning of the magnetic sensors inside 27 of the 770 beamlet apertures. The calculated values have been compared to the experimental data. The work has confirmed the quality of the numerical model, and has also provided useful information on the magnetic non-uniformities due to the edge effects and to the tolerance on permanent magnet remanence.

Population Dynamics of Excited Atoms in Dissipative Cavities

NASA Astrophysics Data System (ADS)

Zou, Hong-Mei; Liu, Yu; Fang, Mao-Fa

2016-10-01

Population dynamics of excited atoms in dissipative cavities is investigated in this work. We present a method of controlling populations of excited atoms in dissipative cavities. For the initial state | e e> A B |00> a b , the repopulation of excited atoms can be obtained by using atom-cavity couplings and non-Markovian effects after the atomic excited energy decays to zero. For the initial state | g g> A B |11> a b , the two atoms can also be populated to the excited states from the initial ground states by using atom-cavity couplings and non-Markovian effects. And the stronger the atom-cavity coupling or the non-Markovian effect is, the larger the number of repopulation of excited atoms is. Particularly, when the atom-cavity coupling or the non-Markovian effect is very strong, the number of repopulation of excited atoms can be close to one in a short time and will tend to a steady value in a long time.

Quantum-mechanical transport equation for atomic systems.

NASA Technical Reports Server (NTRS)

Berman, P. R.

1972-01-01

A quantum-mechanical transport equation (QMTE) is derived which should be applicable to a wide range of problems involving the interaction of radiation with atoms or molecules which are also subject to collisions with perturber atoms. The equation follows the time evolution of the macroscopic atomic density matrix elements of atoms located at classical position R and moving with classical velocity v. It is quantum mechanical in the sense that all collision kernels or rates which appear have been obtained from a quantum-mechanical theory and, as such, properly take into account the energy-level variations and velocity changes of the active (emitting or absorbing) atom produced in collisions with perturber atoms. The present formulation is better suited to problems involving high-intensity external fields, such as those encountered in laser physics.

Predicting Ligand Binding Sites on Protein Surfaces by 3-Dimensional Probability Density Distributions of Interacting Atoms

PubMed Central

Jian, Jhih-Wei; Elumalai, Pavadai; Pitti, Thejkiran; Wu, Chih Yuan; Tsai, Keng-Chang; Chang, Jeng-Yih; Peng, Hung-Pin; Yang, An-Suei

2016-01-01

Predicting ligand binding sites (LBSs) on protein structures, which are obtained either from experimental or computational methods, is a useful first step in functional annotation or structure-based drug design for the protein structures. In this work, the structure-based machine learning algorithm ISMBLab-LIG was developed to predict LBSs on protein surfaces with input attributes derived from the three-dimensional probability density maps of interacting atoms, which were reconstructed on the query protein surfaces and were relatively insensitive to local conformational variations of the tentative ligand binding sites. The prediction accuracy of the ISMBLab-LIG predictors is comparable to that of the best LBS predictors benchmarked on several well-established testing datasets. More importantly, the ISMBLab-LIG algorithm has substantial tolerance to the prediction uncertainties of computationally derived protein structure models. As such, the method is particularly useful for predicting LBSs not only on experimental protein structures without known LBS templates in the database but also on computationally predicted model protein structures with structural uncertainties in the tentative ligand binding sites. PMID:27513851

A benchmark study of the sea-level equation in GIA modelling

NASA Astrophysics Data System (ADS)

Martinec, Zdenek; Klemann, Volker; van der Wal, Wouter; Riva, Riccardo; Spada, Giorgio; Simon, Karen; Blank, Bas; Sun, Yu; Melini, Daniele; James, Tom; Bradley, Sarah

2017-04-01

The sea-level load in glacial isostatic adjustment (GIA) is described by the so called sea-level equation (SLE), which represents the mass redistribution between ice sheets and oceans on a deforming earth. Various levels of complexity of SLE have been proposed in the past, ranging from a simple mean global sea level (the so-called eustatic sea level) to the load with a deforming ocean bottom, migrating coastlines and a changing shape of the geoid. Several approaches to solve the SLE have been derived, from purely analytical formulations to fully numerical methods. Despite various teams independently investigating GIA, there has been no systematic intercomparison amongst the solvers through which the methods may be validated. The goal of this paper is to present a series of benchmark experiments designed for testing and comparing numerical implementations of the SLE. Our approach starts with simple load cases even though the benchmark will not result in GIA predictions for a realistic loading scenario. In the longer term we aim for a benchmark with a realistic loading scenario, and also for benchmark solutions with rotational feedback. The current benchmark uses an earth model for which Love numbers have been computed and benchmarked in Spada et al (2011). In spite of the significant differences in the numerical methods employed, the test computations performed so far show a satisfactory agreement between the results provided by the participants. The differences found can often be attributed to the different approximations inherent to the various algorithms. Literature G. Spada, V. R. Barletta, V. Klemann, R. E. M. Riva, Z. Martinec, P. Gasperini, B. Lund, D. Wolf, L. L. A. Vermeersen, and M. A. King, 2011. A benchmark study for glacial isostatic adjustment codes. Geophys. J. Int. 185: 106-132 doi:10.1111/j.1365-

SeSBench - An initiative to benchmark reactive transport models for environmental subsurface processes

NASA Astrophysics Data System (ADS)

Jacques, Diederik

2017-04-01

As soil functions are governed by a multitude of interacting hydrological, geochemical and biological processes, simulation tools coupling mathematical models for interacting processes are needed. Coupled reactive transport models are a typical example of such coupled tools mainly focusing on hydrological and geochemical coupling (see e.g. Steefel et al., 2015). Mathematical and numerical complexity for both the tool itself or of the specific conceptual model can increase rapidly. Therefore, numerical verification of such type of models is a prerequisite for guaranteeing reliability and confidence and qualifying simulation tools and approaches for any further model application. In 2011, a first SeSBench -Subsurface Environmental Simulation Benchmarking- workshop was held in Berkeley (USA) followed by four other ones. The objective is to benchmark subsurface environmental simulation models and methods with a current focus on reactive transport processes. The final outcome was a special issue in Computational Geosciences (2015, issue 3 - Reactive transport benchmarks for subsurface environmental simulation) with a collection of 11 benchmarks. Benchmarks, proposed by the participants of the workshops, should be relevant for environmental or geo-engineering applications; the latter were mostly related to radioactive waste disposal issues - excluding benchmarks defined for pure mathematical reasons. Another important feature is the tiered approach within a benchmark with the definition of a single principle problem and different sub problems. The latter typically benchmarked individual or simplified processes (e.g. inert solute transport, simplified geochemical conceptual model) or geometries (e.g. batch or one-dimensional, homogeneous). Finally, three codes should be involved into a benchmark. The SeSBench initiative contributes to confidence building for applying reactive transport codes. Furthermore, it illustrates the use of those type of models for different

The Army Pollution Prevention Program: Improving Performance Through Benchmarking.

DTIC Science & Technology

1995-06-01

Washington, DC 20503. 1. AGENCY USE ONLY (Leave Blank) 2. REPORT DATE June 1995 3. REPORT TYPE AND DATES COVERED Final 4. TITLE AND SUBTITLE...unlimited 12b. DISTRIBUTION CODE 13. ABSTRACT (Maximum 200 words) This report investigates the feasibility of using benchmarking as a method for...could use to determine to what degree it should integrate benchmarking with other quality management tools to support the pollution prevention program

NASA Software Engineering Benchmarking Study

NASA Technical Reports Server (NTRS)

Rarick, Heather L.; Godfrey, Sara H.; Kelly, John C.; Crumbley, Robert T.; Wifl, Joel M.

2013-01-01

.onsolidate, collect and, if needed, develop common processes principles and other assets across the Agency in order to provide more consistency in software development and acquisition practices and to reduce the overall cost of maintaining or increasing current NASA CMMI maturity levels. 6. Provide additional support for small projects that includes: (a) guidance for appropriate tailoring of requirements for small projects, (b) availability of suitable tools, including support tool set-up and training, and (c) training for small project personnel, assurance personnel and technical authorities on the acceptable options for tailoring requirements and performing assurance on small projects. 7. Develop software training classes for the more experienced software engineers using on-line training, videos, or small separate modules of training that can be accommodated as needed throughout a project. 8. Create guidelines to structure non-classroom training opportunities such as mentoring, peer reviews, lessons learned sessions, and on-the-job training. 9. Develop a set of predictive software defect data and a process for assessing software testing metric data against it. 10. Assess Agency-wide licenses for commonly used software tools. 11. Fill the knowledge gap in common software engineering practices for new hires and co-ops.12. Work through the Science, Technology, Engineering and Mathematics (STEM) program with universities in strengthening education in the use of common software engineering practices and standards. 13. Follow up this benchmark study with a deeper look into what both internal and external organizations perceive as the scope of software assurance, the value they expect to obtain from it, and the shortcomings they experience in the current practice. 14. Continue interactions with external software engineering environment through collaborations, knowledge sharing, and benchmarking.

Austin Community College Benchmarking Update.

ERIC Educational Resources Information Center

Austin Community Coll., TX. Office of Institutional Effectiveness.

Austin Community College contracted with MGT of America, Inc. in spring 1999 to develop a peer and benchmark (best) practices analysis on key indicators. These indicators were updated in spring 2002 using data from eight Texas community colleges and four non-Texas institutions that represent large, comprehensive, urban community colleges, similar…

Atomic and close-to-atomic scale manufacturing—A trend in manufacturing development

NASA Astrophysics Data System (ADS)

Fang, Fengzhou

2016-12-01

Manufacturing is the foundation of a nation's economy. It is the primary industry to promote economic and social development. To accelerate and upgrade China's manufacturing sector from "precision manufacturing" to "high-performance and high-quality manufacturing", a new breakthrough should be found in terms of achieving a "leap-frog development". Unlike conventional manufacturing, the fundamental theory of "Manufacturing 3.0" is beyond the scope of conventional theory; rather, it is based on new principles and theories at the atomic and/or closeto- atomic scale. Obtaining a dominant role at the international level is a strategic move for China's progress.

How to achieve and prove performance improvement - 15 years of experience in German wastewater benchmarking.

PubMed

Bertzbach, F; Franz, T; Möller, K

2012-01-01

This paper shows the results of performance improvement, which have been achieved in benchmarking projects in the wastewater industry in Germany over the last 15 years. A huge number of changes in operational practice and also in achieved annual savings can be shown, induced in particular by benchmarking at process level. Investigation of this question produces some general findings for the inclusion of performance improvement in a benchmarking project and for the communication of its results. Thus, we elaborate on the concept of benchmarking at both utility and process level, which is still a necessary distinction for the integration of performance improvement into our benchmarking approach. To achieve performance improvement via benchmarking it should be made quite clear that this outcome depends, on one hand, on a well conducted benchmarking programme and, on the other, on the individual situation within each participating utility.

Thermal Performance Benchmarking: Annual Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, Xuhui

In FY16, the thermal performance of the 2014 Honda Accord Hybrid power electronics thermal management systems were benchmarked. Both experiments and numerical simulation were utilized to thoroughly study the thermal resistances and temperature distribution in the power module. Experimental results obtained from the water-ethylene glycol tests provided the junction-to-liquid thermal resistance. The finite element analysis (FEA) and computational fluid dynamics (CFD) models were found to yield a good match with experimental results. Both experimental and modeling results demonstrate that the passive stack is the dominant thermal resistance for both the motor and power electronics systems. The 2014 Accord power electronicsmore » systems yield steady-state thermal resistance values around 42- 50 mm to the 2nd power K/W, depending on the flow rates. At a typical flow rate of 10 liters per minute, the thermal resistance of the Accord system was found to be about 44 percent lower than that of the 2012 Nissan LEAF system that was benchmarked in FY15. The main reason for the difference is that the Accord power module used a metalized-ceramic substrate and eliminated the thermal interface material layers. FEA models were developed to study the transient performance of 2012 Nissan LEAF, 2014 Accord, and two other systems that feature conventional power module designs. The simulation results indicate that the 2012 LEAF power module has lowest thermal impedance at a time scale less than one second. This is probably due to moving low thermally conductive materials further away from the heat source and enhancing the heat spreading effect from the copper-molybdenum plate close to the insulated gate bipolar transistors. When approaching steady state, the Honda system shows lower thermal impedance. Measurement results of the thermal resistance of the 2015 BMW i3 power electronic system indicate that the i3 insulated gate bipolar transistor module has significantly lower junction

7 CFR 1469.7 - Benchmark condition inventory and conservation stewardship plan.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Benchmark condition inventory and conservation...) COMMODITY CREDIT CORPORATION, DEPARTMENT OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS CONSERVATION SECURITY PROGRAM General Provisions § 1469.7 Benchmark condition inventory and conservation stewardship...

Benchmarking variable-density flow in saturated and unsaturated porous media

NASA Astrophysics Data System (ADS)

Guevara Morel, Carlos Roberto; Cremer, Clemens; Graf, Thomas

2015-04-01

In natural environments, fluid density and viscosity can be affected by spatial and temporal variations of solute concentration and/or temperature. These variations can occur, for example, due to salt water intrusion in coastal aquifers, leachate infiltration from waste disposal sites and upconing of saline water from deep aquifers. As a consequence, potentially unstable situations may exist in which a dense fluid overlies a less dense fluid. This situation can produce instabilities that manifest as dense plume fingers that move vertically downwards counterbalanced by vertical upwards flow of the less dense fluid. Resulting free convection increases solute transport rates over large distances and times relative to constant-density flow. Therefore, the understanding of free convection is relevant for the protection of freshwater aquifer systems. The results from a laboratory experiment of saturated and unsaturated variable-density flow and solute transport (Simmons et al., Transp. Porous Medium, 2002) are used as the physical basis to define a mathematical benchmark. The HydroGeoSphere code coupled with PEST are used to estimate the optimal parameter set capable of reproducing the physical model. A grid convergency analysis (in space and time) is also undertaken in order to obtain the adequate spatial and temporal discretizations. The new mathematical benchmark is useful for model comparison and testing of variable-density variably saturated flow in porous media.

Simulation-based comprehensive benchmarking of RNA-seq aligners

PubMed Central

Baruzzo, Giacomo; Hayer, Katharina E; Kim, Eun Ji; Di Camillo, Barbara; FitzGerald, Garret A; Grant, Gregory R

2018-01-01

Alignment is the first step in most RNA-seq analysis pipelines, and the accuracy of downstream analyses depends heavily on it. Unlike most steps in the pipeline, alignment is particularly amenable to benchmarking with simulated data. We performed a comprehensive benchmarking of 14 common splice-aware aligners for base, read, and exon junction-level accuracy and compared default with optimized parameters. We found that performance varied by genome complexity, and accuracy and popularity were poorly correlated. The most widely cited tool underperforms for most metrics, particularly when using default settings. PMID:27941783

Simulation of Rutherford backscattering spectrometry from arbitrary atom structures.

PubMed

Zhang, S; Nordlund, K; Djurabekova, F; Zhang, Y; Velisa, G; Wang, T S

2016-10-01

Rutherford backscattering spectrometry in a channeling direction (RBS/C) is a powerful tool for analysis of the fraction of atoms displaced from their lattice positions. However, it is in many cases not straightforward to analyze what is the actual defect structure underlying the RBS/C signal. To reveal insights of RBS/C signals from arbitrarily complex defective atomic structures, we develop here a method for simulating the RBS/C spectrum from a set of arbitrary read-in atom coordinates (obtained, e.g., from molecular dynamics simulations). We apply the developed method to simulate the RBS/C signals from Ni crystal structures containing randomly displaced atoms, Frenkel point defects, and extended defects, respectively. The RBS/C simulations show that, even for the same number of atoms in defects, the RBS/C signal is much stronger for the extended defects. Comparison with experimental results shows that the disorder profile obtained from RBS/C signals in ion-irradiated Ni is due to a small fraction of extended defects rather than a large number of individual random atoms.

Simulation of Rutherford backscattering spectrometry from arbitrary atom structures

DOE PAGES

Zhang, S.; Univ. of Helsinki; Nordlund, Kai; ...

2016-10-25

Rutherford backscattering spectrometry in a channeling direction (RBS/C) is a powerful tool for analysis of the fraction of atoms displaced from their lattice positions. However, it is in many cases not straightforward to analyze what is the actual defect structure underlying the RBS/C signal. To reveal insights of RBS/C signals from arbitrarily complex defective atomic structures, we develop in this paper a method for simulating the RBS/C spectrum from a set of arbitrary read-in atom coordinates (obtained, e.g., from molecular dynamics simulations). We apply the developed method to simulate the RBS/C signals from Ni crystal structures containing randomly displaced atoms,more » Frenkel point defects, and extended defects, respectively. The RBS/C simulations show that, even for the same number of atoms in defects, the RBS/C signal is much stronger for the extended defects. Finally, comparison with experimental results shows that the disorder profile obtained from RBS/C signals in ion-irradiated Ni is due to a small fraction of extended defects rather than a large number of individual random atoms.« less

Simulation of Rutherford backscattering spectrometry from arbitrary atom structures

NASA Astrophysics Data System (ADS)

Zhang, S.; Nordlund, K.; Djurabekova, F.; Zhang, Y.; Velisa, G.; Wang, T. S.

2016-10-01

Rutherford backscattering spectrometry in a channeling direction (RBS/C) is a powerful tool for analysis of the fraction of atoms displaced from their lattice positions. However, it is in many cases not straightforward to analyze what is the actual defect structure underlying the RBS/C signal. To reveal insights of RBS/C signals from arbitrarily complex defective atomic structures, we develop here a method for simulating the RBS/C spectrum from a set of arbitrary read-in atom coordinates (obtained, e.g., from molecular dynamics simulations). We apply the developed method to simulate the RBS/C signals from Ni crystal structures containing randomly displaced atoms, Frenkel point defects, and extended defects, respectively. The RBS/C simulations show that, even for the same number of atoms in defects, the RBS/C signal is much stronger for the extended defects. Comparison with experimental results shows that the disorder profile obtained from RBS/C signals in ion-irradiated Ni is due to a small fraction of extended defects rather than a large number of individual random atoms.

Generating Shifting Workloads to Benchmark Adaptability in Relational Database Systems

NASA Astrophysics Data System (ADS)

Rabl, Tilmann; Lang, Andreas; Hackl, Thomas; Sick, Bernhard; Kosch, Harald

A large body of research concerns the adaptability of database systems. Many commercial systems already contain autonomic processes that adapt configurations as well as data structures and data organization. Yet there is virtually no possibility for a just measurement of the quality of such optimizations. While standard benchmarks have been developed that simulate real-world database applications very precisely, none of them considers variations in workloads produced by human factors. Today’s benchmarks test the performance of database systems by measuring peak performance on homogeneous request streams. Nevertheless, in systems with user interaction access patterns are constantly shifting. We present a benchmark that simulates a web information system with interaction of large user groups. It is based on the analysis of a real online eLearning management system with 15,000 users. The benchmark considers the temporal dependency of user interaction. Main focus is to measure the adaptability of a database management system according to shifting workloads. We will give details on our design approach that uses sophisticated pattern analysis and data mining techniques.

Investigating the Transonic Flutter Boundary of the Benchmark Supercritical Wing

NASA Technical Reports Server (NTRS)

Heeg, Jennifer; Chwalowski, Pawel

2017-01-01

This paper builds on the computational aeroelastic results published previously and generated in support of the second Aeroelastic Prediction Workshop for the NASA Benchmark Supercritical Wing configuration. The computational results are obtained using FUN3D, an unstructured grid Reynolds-Averaged Navier-Stokes solver developed at the NASA Langley Research Center. The analysis results focus on understanding the dip in the transonic flutter boundary at a single Mach number (0.74), exploring an angle of attack range of ??1 to 8 and dynamic pressures from wind off to beyond flutter onset. The rigid analysis results are examined for insights into the behavior of the aeroelastic system. Both static and dynamic aeroelastic simulation results are also examined.

A Benchmark Problem for Development of Autonomous Structural Modal Identification

NASA Technical Reports Server (NTRS)

Pappa, Richard S.; Woodard, Stanley E.; Juang, Jer-Nan

1996-01-01

This paper summarizes modal identification results obtained using an autonomous version of the Eigensystem Realization Algorithm on a dynamically complex, laboratory structure. The benchmark problem uses 48 of 768 free-decay responses measured in a complete modal survey test. The true modal parameters of the structure are well known from two previous, independent investigations. Without user involvement, the autonomous data analysis identified 24 to 33 structural modes with good to excellent accuracy in 62 seconds of CPU time (on a DEC Alpha 4000 computer). The modal identification technique described in the paper is the baseline algorithm for NASA's Autonomous Dynamics Determination (ADD) experiment scheduled to fly on International Space Station assembly flights in 1997-1999.

Benchmarking and performance analysis of the CM-2. [SIMD computer

NASA Technical Reports Server (NTRS)

Myers, David W.; Adams, George B., II

1988-01-01

A suite of benchmarking routines testing communication, basic arithmetic operations, and selected kernel algorithms written in LISP and PARIS was developed for the CM-2. Experiment runs are automated via a software framework that sequences individual tests, allowing for unattended overnight operation. Multiple measurements are made and treated statistically to generate well-characterized results from the noisy values given by cm:time. The results obtained provide a comparison with similar, but less extensive, testing done on a CM-1. Tests were chosen to aid the algorithmist in constructing fast, efficient, and correct code on the CM-2, as well as gain insight into what performance criteria are needed when evaluating parallel processing machines.

Evaluating the Effect of Labeled Benchmarks on Children's Number Line Estimation Performance and Strategy Use.

PubMed

Peeters, Dominique; Sekeris, Elke; Verschaffel, Lieven; Luwel, Koen

2017-01-01

Some authors argue that age-related improvements in number line estimation (NLE) performance result from changes in strategy use. More specifically, children's strategy use develops from only using the origin of the number line, to using the origin and the endpoint, to eventually also relying on the midpoint of the number line. Recently, Peeters et al. (unpublished) investigated whether the provision of additional unlabeled benchmarks at 25, 50, and 75% of the number line, positively affects third and fifth graders' NLE performance and benchmark-based strategy use. It was found that only the older children benefitted from the presence of these benchmarks at the quartiles of the number line (i.e., 25 and 75%), as they made more use of these benchmarks, leading to more accurate estimates. A possible explanation for this lack of improvement in third graders might be their inability to correctly link the presented benchmarks with their corresponding numerical values. In the present study, we investigated whether labeling these benchmarks with their corresponding numerical values, would have a positive effect on younger children's NLE performance and quartile-based strategy use as well. Third and sixth graders were assigned to one of three conditions: (a) a control condition with an empty number line bounded by 0 at the origin and 1,000 at the endpoint, (b) an unlabeled condition with three additional external benchmarks without numerical labels at 25, 50, and 75% of the number line, and (c) a labeled condition in which these benchmarks were labeled with 250, 500, and 750, respectively. Results indicated that labeling the benchmarks has a positive effect on third graders' NLE performance and quartile-based strategy use, whereas sixth graders already benefited from the mere provision of unlabeled benchmarks. These findings imply that children's benchmark-based strategy use can be stimulated by adding additional externally provided benchmarks on the number line, but that

Encoding color information for visual tracking: Algorithms and benchmark.

PubMed

Liang, Pengpeng; Blasch, Erik; Ling, Haibin

2015-12-01

While color information is known to provide rich discriminative clues for visual inference, most modern visual trackers limit themselves to the grayscale realm. Despite recent efforts to integrate color in tracking, there is a lack of comprehensive understanding of the role color information can play. In this paper, we attack this problem by conducting a systematic study from both the algorithm and benchmark perspectives. On the algorithm side, we comprehensively encode 10 chromatic models into 16 carefully selected state-of-the-art visual trackers. On the benchmark side, we compile a large set of 128 color sequences with ground truth and challenge factor annotations (e.g., occlusion). A thorough evaluation is conducted by running all the color-encoded trackers, together with two recently proposed color trackers. A further validation is conducted on an RGBD tracking benchmark. The results clearly show the benefit of encoding color information for tracking. We also perform detailed analysis on several issues, including the behavior of various combinations between color model and visual tracker, the degree of difficulty of each sequence for tracking, and how different challenge factors affect the tracking performance. We expect the study to provide the guidance, motivation, and benchmark for future work on encoding color in visual tracking.

A new method for mapping the three-dimensional atomic distribution within nanoparticles by atom probe tomography (APT).

PubMed

Kim, Se-Ho; Kang, Phil Woong; Park, O Ok; Seol, Jae-Bok; Ahn, Jae-Pyoung; Lee, Ji Yeong; Choi, Pyuck-Pa

2018-07-01

We present a new method of preparing needle-shaped specimens for atom probe tomography from freestanding Pd and C-supported Pt nanoparticles. The method consists of two steps, namely electrophoresis of nanoparticles on a flat Cu substrate followed by electrodeposition of a Ni film acting as an embedding matrix for the nanoparticles. Atom probe specimen preparation can be subsequently carried out by means of focused-ion-beam milling. Using this approach, we have been able to perform correlative atom probe tomography and transmission electron microscopy analyses on both nanoparticle systems. Reliable mass spectra and three-dimensional atom maps could be obtained for Pd nanoparticle specimens. In contrast, atom probe samples prepared from C-supported Pt nanoparticles showed uneven field evaporation and hence artifacts in the reconstructed atom maps. Our developed method is a viable means of mapping the three-dimensional atomic distribution within nanoparticles and is expected to contribute to an improved understanding of the structure-composition-property relationships of various nanoparticle systems. Copyright © 2018 Elsevier B.V. All rights reserved.

Convergent Close-Coupling Approach to Electron-Atom Collisions

NASA Technical Reports Server (NTRS)

Bray, Igor; Stelbovics, Andris

2007-01-01

It was with great pleasure and honour to accept the invitation to make a presentation at the symposium celebrating the life-long work of Aaron Temkin and Richard Drachman. The work of Aaron Temkin was particularly influential on our own during the development of the CCC method for electron-atom collisions. There are a number of key problems that need to be dealt with when developing a general computational approach to such collisions. Traditionally, the electron energy range was subdivided into the low, intermediate, and high energies. At the low energies only a finite number of channels are open and variational or close-coupling techniques could be used to obtain accurate results. At high energies an infinite number of discrete channels and the target continuum are open, but perturbative techniques are able to yield accurate results. However, at the intermediate energies perturbative techniques fail and computational approaches need to be found for treating the infinite number of open channels. In addition, there are also problems associated with the identical nature of electrons and the difficulty of implementing the boundary conditions for ionization processes. The beauty of the Temkin-Poet model of electron-hydrogen scattering is that it simplifies the full computational problem by neglecting any non-zero orbital angular momenta in the partial-wave expansion, without loosing the complexity associated with the above-mentioned problems. The unique nature of the problem allowed for accurate solution leading to benchmark results which could then be used to test the much more general approaches to electron-atom collision problems. The immense value of the Temkin-Poet model is readily summarised by the fact that the initial papers of Temkin and Poet have been collectively cited around 250 times to date and are still being cited in present times. Many of the citations came from our own work during the course of the development of the CCC method, which we now describe.

Benchmarking high performance computing architectures with CMS’ skeleton framework

DOE PAGES

Sexton-Kennedy, E.; Gartung, P.; Jones, C. D.

2017-11-23

Here, in 2012 CMS evaluated which underlying concurrency technology would be the best to use for its multi-threaded framework. The available technologies were evaluated on the high throughput computing systems dominating the resources in use at that time. A skeleton framework benchmarking suite that emulates the tasks performed within a CMSSW application was used to select Intel’s Thread Building Block library, based on the measured overheads in both memory and CPU on the different technologies benchmarked. In 2016 CMS will get access to high performance computing resources that use new many core architectures; machines such as Cori Phase 1&2, Theta,more » Mira. Because of this we have revived the 2012 benchmark to test it’s performance and conclusions on these new architectures. This talk will discuss the results of this exercise.« less

Nonparametric estimation of benchmark doses in environmental risk assessment

PubMed Central

Piegorsch, Walter W.; Xiong, Hui; Bhattacharya, Rabi N.; Lin, Lizhen

2013-01-01

Summary An important statistical objective in environmental risk analysis is estimation of minimum exposure levels, called benchmark doses (BMDs), that induce a pre-specified benchmark response in a dose-response experiment. In such settings, representations of the risk are traditionally based on a parametric dose-response model. It is a well-known concern, however, that if the chosen parametric form is misspecified, inaccurate and possibly unsafe low-dose inferences can result. We apply a nonparametric approach for calculating benchmark doses, based on an isotonic regression method for dose-response estimation with quantal-response data (Bhattacharya and Kong, 2007). We determine the large-sample properties of the estimator, develop bootstrap-based confidence limits on the BMDs, and explore the confidence limits’ small-sample properties via a short simulation study. An example from cancer risk assessment illustrates the calculations. PMID:23914133

Benchmarking high performance computing architectures with CMS’ skeleton framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sexton-Kennedy, E.; Gartung, P.; Jones, C. D.

Here, in 2012 CMS evaluated which underlying concurrency technology would be the best to use for its multi-threaded framework. The available technologies were evaluated on the high throughput computing systems dominating the resources in use at that time. A skeleton framework benchmarking suite that emulates the tasks performed within a CMSSW application was used to select Intel’s Thread Building Block library, based on the measured overheads in both memory and CPU on the different technologies benchmarked. In 2016 CMS will get access to high performance computing resources that use new many core architectures; machines such as Cori Phase 1&2, Theta,more » Mira. Because of this we have revived the 2012 benchmark to test it’s performance and conclusions on these new architectures. This talk will discuss the results of this exercise.« less

Giant (12 ×12 ) and (4 ×8 ) reconstructions of the 6 H -SiC(0001) surface obtained by progressive enrichment in Si atoms

NASA Astrophysics Data System (ADS)

Martrou, David; Leoni, Thomas; Chaumeton, Florian; Castanié, Fabien; Gauthier, Sébastien; Bouju, Xavier

2018-02-01

Silicon carbide (SiC) is nowadays a major material for applications in high power electronics, quantum optics, or nitride semiconductors growth. Mastering the surface of SiC substrate is crucial to obtain reproducible results. Previous studies on the 6 H -SiC(0001) surface have determined several reconstructions, including the (√{3 }×√{3 }) -R 30∘ and the (3 ×3 ) . Here, we introduce a process of progressive Si enrichment that leads to the formation of two reconstructions, the giant (12 ×12 ) and the (4 ×8 ) . From electron diffraction and tunneling microscopy completed by molecular dynamics simulations, we build models introducing a type of Si adatom bridging two Si surface atoms. Using these Si bridges, we also propose a structure for two other reconstructions, the (2 √{3 }×2 √{3 }) -R 30∘ and the (2 √{3 }×2 √{13 } ). We show that five reconstructions follow each other with Si coverage ranging from 1 and 1.444 monolayer. This result opens the way to greatly improve the control of 6 H -SiC(0001) at the atomic scale.

Higher Education Ranking and Leagues Tables: Lessons Learned from Benchmarking

ERIC Educational Resources Information Center

Proulx, Roland

2007-01-01

The paper intends to contribute to the debate on ranking and league tables by adopting a critical approach to ranking methodologies from the point of view of a university benchmarking exercise. The absence of a strict benchmarking exercise in the ranking process has been, in the opinion of the author, one of the major problems encountered in the…

Analytical solutions for benchmarking cold regions subsurface water flow and energy transport models: one-dimensional soil thaw with conduction and advection

USGS Publications Warehouse

Kurylyk, Barret L.; McKenzie, Jeffrey M; MacQuarrie, Kerry T. B.; Voss, Clifford I.

2014-01-01

Numerous cold regions water flow and energy transport models have emerged in recent years. Dissimilarities often exist in their mathematical formulations and/or numerical solution techniques, but few analytical solutions exist for benchmarking flow and energy transport models that include pore water phase change. This paper presents a detailed derivation of the Lunardini solution, an approximate analytical solution for predicting soil thawing subject to conduction, advection, and phase change. Fifteen thawing scenarios are examined by considering differences in porosity, surface temperature, Darcy velocity, and initial temperature. The accuracy of the Lunardini solution is shown to be proportional to the Stefan number. The analytical solution results obtained for soil thawing scenarios with water flow and advection are compared to those obtained from the finite element model SUTRA. Three problems, two involving the Lunardini solution and one involving the classic Neumann solution, are recommended as standard benchmarks for future model development and testing.

A Scanning Quantum Cryogenic Atom Microscope

NASA Astrophysics Data System (ADS)

Lev, Benjamin

Microscopic imaging of local magnetic fields provides a window into the organizing principles of complex and technologically relevant condensed matter materials. However, a wide variety of intriguing strongly correlated and topologically nontrivial materials exhibit poorly understood phenomena outside the detection capability of state-of-the-art high-sensitivity, high-resolution scanning probe magnetometers. We introduce a quantum-noise-limited scanning probe magnetometer that can operate from room-to-cryogenic temperatures with unprecedented DC-field sensitivity and micron-scale resolution. The Scanning Quantum Cryogenic Atom Microscope (SQCRAMscope) employs a magnetically levitated atomic Bose-Einstein condensate (BEC), thereby providing immunity to conductive and blackbody radiative heating. The SQCRAMscope has a field sensitivity of 1.4 nT per resolution-limited point (2 um), or 6 nT / Hz1 / 2 per point at its duty cycle. Compared to point-by-point sensors, the long length of the BEC provides a naturally parallel measurement, allowing one to measure nearly one-hundred points with an effective field sensitivity of 600 pT / Hz1 / 2 each point during the same time as a point-by-point scanner would measure these points sequentially. Moreover, it has a noise floor of 300 pT and provides nearly two orders of magnitude improvement in magnetic flux sensitivity (down to 10- 6 Phi0 / Hz1 / 2) over previous atomic probe magnetometers capable of scanning near samples. These capabilities are for the first time carefully benchmarked by imaging magnetic fields arising from microfabricated wire patterns and done so using samples that may be scanned, cryogenically cooled, and easily exchanged. We anticipate the SQCRAMscope will provide charge transport images at temperatures from room to \\x9D4K in unconventional superconductors and topologically nontrivial materials.

Alternative industrial carbon emissions benchmark based on input-output analysis

NASA Astrophysics Data System (ADS)

Han, Mengyao; Ji, Xi

2016-12-01

Some problems exist in the current carbon emissions benchmark setting systems. The primary consideration for industrial carbon emissions standards highly relate to direct carbon emissions (power-related emissions) and only a portion of indirect emissions are considered in the current carbon emissions accounting processes. This practice is insufficient and may cause double counting to some extent due to mixed emission sources. To better integrate and quantify direct and indirect carbon emissions, an embodied industrial carbon emissions benchmark setting method is proposed to guide the establishment of carbon emissions benchmarks based on input-output analysis. This method attempts to link direct carbon emissions with inter-industrial economic exchanges and systematically quantifies carbon emissions embodied in total product delivery chains. The purpose of this study is to design a practical new set of embodied intensity-based benchmarks for both direct and indirect carbon emissions. Beijing, at the first level of carbon emissions trading pilot schemes in China, plays a significant role in the establishment of these schemes and is chosen as an example in this study. The newly proposed method tends to relate emissions directly to each responsibility in a practical way through the measurement of complex production and supply chains and reduce carbon emissions from their original sources. This method is expected to be developed under uncertain internal and external contexts and is further expected to be generalized to guide the establishment of industrial benchmarks for carbon emissions trading schemes in China and other countries.

Benchmarking health IT among OECD countries: better data for better policy

PubMed Central

Adler-Milstein, Julia; Ronchi, Elettra; Cohen, Genna R; Winn, Laura A Pannella; Jha, Ashish K

2014-01-01

Objective To develop benchmark measures of health information and communication technology (ICT) use to facilitate cross-country comparisons and learning. Materials and methods The effort is led by the Organisation for Economic Co-operation and Development (OECD). Approaches to definition and measurement within four ICT domains were compared across seven OECD countries in order to identify functionalities in each domain. These informed a set of functionality-based benchmark measures, which were refined in collaboration with representatives from more than 20 OECD and non-OECD countries. We report on progress to date and remaining work to enable countries to begin to collect benchmark data. Results The four benchmarking domains include provider-centric electronic record, patient-centric electronic record, health information exchange, and tele-health. There was broad agreement on functionalities in the provider-centric electronic record domain (eg, entry of core patient data, decision support), and less agreement in the other three domains in which country representatives worked to select benchmark functionalities. Discussion Many countries are working to implement ICTs to improve healthcare system performance. Although many countries are looking to others as potential models, the lack of consistent terminology and approach has made cross-national comparisons and learning difficult. Conclusions As countries develop and implement strategies to increase the use of ICTs to promote health goals, there is a historic opportunity to enable cross-country learning. To facilitate this learning and reduce the chances that individual countries flounder, a common understanding of health ICT adoption and use is needed. The OECD-led benchmarking process is a crucial step towards achieving this. PMID:23721983

Benchmarking health IT among OECD countries: better data for better policy.

PubMed

Adler-Milstein, Julia; Ronchi, Elettra; Cohen, Genna R; Winn, Laura A Pannella; Jha, Ashish K

2014-01-01

To develop benchmark measures of health information and communication technology (ICT) use to facilitate cross-country comparisons and learning. The effort is led by the Organisation for Economic Co-operation and Development (OECD). Approaches to definition and measurement within four ICT domains were compared across seven OECD countries in order to identify functionalities in each domain. These informed a set of functionality-based benchmark measures, which were refined in collaboration with representatives from more than 20 OECD and non-OECD countries. We report on progress to date and remaining work to enable countries to begin to collect benchmark data. The four benchmarking domains include provider-centric electronic record, patient-centric electronic record, health information exchange, and tele-health. There was broad agreement on functionalities in the provider-centric electronic record domain (eg, entry of core patient data, decision support), and less agreement in the other three domains in which country representatives worked to select benchmark functionalities. Many countries are working to implement ICTs to improve healthcare system performance. Although many countries are looking to others as potential models, the lack of consistent terminology and approach has made cross-national comparisons and learning difficult. As countries develop and implement strategies to increase the use of ICTs to promote health goals, there is a historic opportunity to enable cross-country learning. To facilitate this learning and reduce the chances that individual countries flounder, a common understanding of health ICT adoption and use is needed. The OECD-led benchmarking process is a crucial step towards achieving this.

Performance Against WELCOA's Worksite Health Promotion Benchmarks Across Years Among Selected US Organizations.

PubMed

Weaver, GracieLee M; Mendenhall, Brandon N; Hunnicutt, David; Picarella, Ryan; Leffelman, Brittanie; Perko, Michael; Bibeau, Daniel L

2018-05-01

The purpose of this study was to quantify the performance of organizations' worksite health promotion (WHP) activities against the benchmarking criteria included in the Well Workplace Checklist (WWC). The Wellness Council of America (WELCOA) developed a tool to assess WHP with its 100-item WWC, which represents WELCOA's 7 performance benchmarks. Workplaces. This study includes a convenience sample of organizations who completed the checklist from 2008 to 2015. The sample size was 4643 entries from US organizations. The WWC includes demographic questions, general questions about WHP programs, and scales to measure the performance against the WELCOA 7 benchmarks. Descriptive analyses of WWC items were completed separately for each year of the study period. The majority of the organizations represented each year were multisite, multishift, medium- to large-sized companies mostly in the services industry. Despite yearly changes in participating organizations, results across the WELCOA 7 benchmark scores were consistent year to year. Across all years, benchmarks that organizations performed the lowest were senior-level support, data collection, and programming; wellness teams and supportive environments were the highest scoring benchmarks. In an era marked with economic swings and health-care reform, it appears that organizations are staying consistent in their performance across these benchmarks. The WWC could be useful for organizations, practitioners, and researchers in assessing the quality of WHP programs.

The benchmark aeroelastic models program: Description and highlights of initial results

NASA Technical Reports Server (NTRS)

Bennett, Robert M.; Eckstrom, Clinton V.; Rivera, Jose A., Jr.; Dansberry, Bryan E.; Farmer, Moses G.; Durham, Michael H.

1991-01-01

An experimental effort was implemented in aeroelasticity called the Benchmark Models Program. The primary purpose of this program is to provide the necessary data to evaluate computational fluid dynamic codes for aeroelastic analysis. It also focuses on increasing the understanding of the physics of unsteady flows and providing data for empirical design. An overview is given of this program and some results obtained in the initial tests are highlighted. The tests that were completed include measurement of unsteady pressures during flutter of rigid wing with a NACA 0012 airfoil section and dynamic response measurements of a flexible rectangular wing with a thick circular arc airfoil undergoing shock boundary layer oscillations.

Staffing benchmarks for histology laboratories.

PubMed

Buesa, René J

2010-06-01

This article summarizes annual workloads for staff positions and work flow productivity (WFP) values from 247 human pathology, 31 veterinary, and 35 forensic histology laboratories (histolabs). There are single summaries for veterinary and forensic histolabs, but the data from human pathology are divided into 2 groups because of statistically significant differences between those from Spain and 6 Hispano American countries (SpHA) and the rest from the United States and 17 other countries. The differences reflect the way the work is organized, but the histotechnicians and histotechnologists (histotechs) from SpHA have the same task productivity levels as those from any other country (Buesa RJ. Productivity standards for histology laboratories. [YADPA 50,552]). The information is also segregated by groups of histolabs with increasing workloads; this aspect also showed statistical differences. The information from human pathology histolabs other than those from SpHA were used to calculate staffing annual benchmarks for pathologists (from 3700 to 6500 cases depending on the histolab annual workload), pathology assistants (20,000 cases), staff histotechs (9900 blocks), cutting histotechs (15,000 blocks), histotechs doing special procedures (9500 slides if done manually or 15,000 slides with autostainers), dieners (100 autopsies), laboratory aides and transcriptionists (15,000 cases each), and secretaries (20,000 cases). There are also recommendations about workload limits for supervisory staff (lead techs and supervisors) and when neither is required. Each benchmark was related with the productivity of the different tasks they include (Buesa RJ. Productivity standards for histology laboratories. [YADPA 50,552]) to calculate the hours per year required to complete them. The relationship between workload and benchmarks allows the director of pathology to determine the staff needed for the efficient operation of the histolab.

Sensitivity Analysis of OECD Benchmark Tests in BISON

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swiler, Laura Painton; Gamble, Kyle; Schmidt, Rodney C.

2015-09-01

This report summarizes a NEAMS (Nuclear Energy Advanced Modeling and Simulation) project focused on sensitivity analysis of a fuels performance benchmark problem. The benchmark problem was defined by the Uncertainty Analysis in Modeling working group of the Nuclear Science Committee, part of the Nuclear Energy Agency of the Organization for Economic Cooperation and Development (OECD ). The benchmark problem involv ed steady - state behavior of a fuel pin in a Pressurized Water Reactor (PWR). The problem was created in the BISON Fuels Performance code. Dakota was used to generate and analyze 300 samples of 17 input parameters defining coremore » boundary conditions, manuf acturing tolerances , and fuel properties. There were 24 responses of interest, including fuel centerline temperatures at a variety of locations and burnup levels, fission gas released, axial elongation of the fuel pin, etc. Pearson and Spearman correlatio n coefficients and Sobol' variance - based indices were used to perform the sensitivity analysis. This report summarizes the process and presents results from this study.« less

Parallelization of NAS Benchmarks for Shared Memory Multiprocessors

NASA Technical Reports Server (NTRS)

Waheed, Abdul; Yan, Jerry C.; Saini, Subhash (Technical Monitor)

1998-01-01

This paper presents our experiences of parallelizing the sequential implementation of NAS benchmarks using compiler directives on SGI Origin2000 distributed shared memory (DSM) system. Porting existing applications to new high performance parallel and distributed computing platforms is a challenging task. Ideally, a user develops a sequential version of the application, leaving the task of porting to new generations of high performance computing systems to parallelization tools and compilers. Due to the simplicity of programming shared-memory multiprocessors, compiler developers have provided various facilities to allow the users to exploit parallelism. Native compilers on SGI Origin2000 support multiprocessing directives to allow users to exploit loop-level parallelism in their programs. Additionally, supporting tools can accomplish this process automatically and present the results of parallelization to the users. We experimented with these compiler directives and supporting tools by parallelizing sequential implementation of NAS benchmarks. Results reported in this paper indicate that with minimal effort, the performance gain is comparable with the hand-parallelized, carefully optimized, message-passing implementations of the same benchmarks.

Processor Emulator with Benchmark Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lloyd, G. Scott; Pearce, Roger; Gokhale, Maya

2015-11-13

A processor emulator and a suite of benchmark applications have been developed to assist in characterizing the performance of data-centric workloads on current and future computer architectures. Some of the applications have been collected from other open source projects. For more details on the emulator and an example of its usage, see reference [1].

Equilibrium Partitioning Sediment Benchmarks (ESBs) for the ...