Market-Based and System-Wide Fuel Cycle Optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, Paul

The Dynamic Resource Exchange (DRE) gives agency to consumer facilities to determine the preference of any particular trade that is offered by suppliers to satisfy its requests. This provides a natural balance of power in the relationship between consumers and suppliers. However, in situations in which suppliers have flexibility surrounding the way that they respond to individual requests, they have no mechanism to assess how different bids will be received by the consumer. Theoretically, a supplier can offer multiple bids to respond to a given request in an attempt to “cover their bases”, but this introduces more arcs into themore » underlying network flow problem, increasing the cost to solve the problem. In the extreme, when a supplier can continuously vary the characteristics of the bid, this can represent a large number of additional arcs and have real performance consequences. To remedy this inefficiency in the implementation of the market-level optimization, the definition of a request has been extended to include a function that can be used by the supplier to query the preference that would be assigned by a consumer for a potential bid. The supplier is then free to implement arbitrarily complex algorithms to revise/optimize its bid based on responses to this function. A supplier can chose to not invoke the function at all, mimicking the original DRE behavior, can use it to select among a small set of discrete choices, or can implement an internal algorithm to seek an optimum bid on a continuous parameter space. This capability was demonstrated with a storage facility that preferred material with a specific decay heat that was as close as possible to the maximum allowable decay heat, while requiring the specific decay heat to fall between a minimum and maximum level. This archetype was used to fill multiple storage roles in a simulation that also included a standard recipe reactor: wet storage with no maximum allowable specific decay heat, dry storage with a modest maximum allowable specific decay heat, and a geologic repository with a low maximum allowable specific decay heat. In such a simulation, the reactor, wet storage and dry storage always offer their material to be taken by one of the other storage facilities. The preference function of the consumer would always ensure that material only flowed when the decay heat was sufficiently low, but in the absence of objective function callbacks, would allow for many superfluous offers that exceeded those limits. If this archetype also uses a callback function to probe the preference of the receiving facility for each possible offer, it can avoid making offers that are not going to be accepted by the receiving facility.« less

Aerodynamic analysis of seamless horizontal stabilizer

NASA Astrophysics Data System (ADS)

Nithya, S.; Kanimozhi, S.

2017-05-01

This project presents an investigative view into the concept of seamless aeroelastic wing and hingeless flexible trailing edge. Wings are designed to provide maximum lift and minimal drag and weight. But with conventional wings where rivets are used and the control surfaces are separately hinged, parasite drag comes into play. This project is about analysing a smooth seamless wing with hinge-less flexible trailing edge. This type of wing reduces the drag considerably and the hinge-less trailing edge leads to a minimal control demand and reduces the noise produced when the aircraft comes for landing. Seamless aeroelastic wing will function as an integrated one piece lifting and control surface. It has been designed to enhance a desirable wing camber for control by deflecting a hinge-less flexible trailing edge part instead of a traditional hinged control surface. This kind of flexible wing can be achieved either by a curved beam and disc actuation mechanism or by piezo-electric materials, whose shape change can be achieved by electricity. The intent of this project is to analyze the effects of introducing the concept of Seamless Wing to the horizontal stabilizer. While the removal of rivets and serrations that hinge the elevators to the stabilizer reduces the overall drag by a reasonable value, the overall concept of a control surface-less stabilizer where the maneuvers are done by deflecting the trailing edge offers better maneuverability.

eduCRATE--a Virtual Hospital architecture.

PubMed

Stoicu-Tivadar, Lăcrimioara; Stoicu-Tivadar, Vasile; Berian, Dorin; Drăgan, Simona; Serban, Alexandru; Serban, Corina

2014-01-01

eduCRATE is a complex project proposal which aims to develop a virtual learning environment offering interactive digital content through original and integrated solutions using cloud computing, complex multimedia systems in virtual space and personalized design with avatars. Compared to existing similar products the project brings the novelty of using languages for medical guides in order to ensure a maximum of flexibility. The Virtual Hospital simulations will create interactive clinical scenarios for which students will find solutions for positive diagnosis and therapeutic management. The solution based on cloud computing and immersive multimedia is an attractive option in education because is economical and it matches the current working style of the young generation to whom it addresses.

Coaxial CoMoO4 nanowire arrays with chemically integrated conductive coating for high-performance flexible all-solid-state asymmetric supercapacitors.

PubMed

Chen, Yaping; Liu, Borui; Liu, Qi; Wang, Jun; Li, Zhanshuang; Jing, Xiaoyan; Liu, Lianhe

2015-10-07

Flexible all-solid-state supercapacitors have offered promising applications as novel energy storage devices based on their merits, such as small size, low cost, light weight and high wearability for high-performance portable electronics. However, one major challenge to make flexible all-solid-state supercapacitors depends on the improvement of electrode materials with higher electrical conductivity properties and longer cycling stability. In this article, we put forward a simple strategy to in situ synthesize 1D CoMoO4 nanowires (NWs), using highly conductive CC and an electrically conductive PPy wrapping layer on CoMoO4 NW arrays for high performance electrode materials. The results show that the CoMoO4/PPy hybrid NW electrode exhibits a high areal specific capacitance of ca. 1.34 F cm(-2) at a current density of 2 mA cm(-2), which is remarkably better than the corresponding values for a pure CoMoO4 NW electrode of 0.7 F cm(-2). An excellent cycling performance of nanocomposites of up to 95.2% (ca. 1.12 F cm(-2)) is achieved after 2000 cycles compared to pristine CoMoO4 NWs. In addition, we fabricate flexible all-solid-state ASC which can be cycled reversibly in the voltage range of 0-1.7 V, and exhibits a maximum energy density of 104.7 W h kg(-1) (3.522 mW h cm(-3)), demonstrating great potential for practical applications in flexible energy storage electronics.

Airfoil System for Cruising Flight

NASA Technical Reports Server (NTRS)

Shams, Qamar A. (Inventor); Liu, Tianshu (Inventor)

2014-01-01

An airfoil system includes an airfoil body and at least one flexible strip. The airfoil body has a top surface and a bottom surface, a chord length, a span, and a maximum thickness. Each flexible strip is attached along at least one edge thereof to either the top or bottom surface of the airfoil body. The flexible strip has a spanwise length that is a function of the airfoil body's span, a chordwise width that is a function of the airfoil body's chord length, and a thickness that is a function of the airfoil body's maximum thickness.

Flexible Dielectric Nanocomposites with Ultrawide Zero-Temperature Coefficient Windows for Electrical Energy Storage and Conversion under Extreme Conditions.

PubMed

Shehzad, Khurram; Xu, Yang; Gao, Chao; Li, Hanying; Dang, Zhi-Min; Hasan, Tawfique; Luo, Jack; Duan, Xiangfeng

2017-03-01

Polymer dielectrics offer key advantages over their ceramic counterparts such as flexibility, scalability, low cost, and high breakdown voltages. However, a major drawback that limits more widespread application of polymer dielectrics is their temperature-dependent dielectric properties. Achieving dielectric constants with low/zero-temperature coefficient (L/0TC) over a broad temperature range is essential for applications in diverse technologies. Here, we report a hybrid filler strategy to produce polymer composites with an ultrawide L/0TC window of dielectric constant, as well as a significantly enhanced dielectric value, maximum energy storage density, thermal conductivity, and stability. By creating a series of percolative polymer composites, we demonstrated hybrid carbon filler based composites can exhibit a zero-temperature coefficient window of 200 °C (from -50 to 150 °C), the widest 0TC window for all polymer composite dielectrics reported to date. We further show the electric and dielectric temperature coefficient of the composites is highly stable against stretching and bending, even under AC electric field with frequency up to 1 MHz. We envision that our method will push the functional limits of polymer dielectrics for flexible electronics in extreme conditions such as in hybrid vehicles, aerospace, power electronics, and oil/gas exploration.

Self-supporting activated carbon/carbon nanotube/reduced graphene oxide flexible electrode for high performance supercapacitor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xing; Tang, Yao; Song, Junhua

A self-supporting and flexible activated carbon/carbon nanotube/reduced graphene oxide (AC/CNT/RGO) film has been rationally designed for constructing high- performance supercapacitor. The AC/CNT/RGO film is prepared by anchoring the AC particles with a 3D and porous framework built by hierarchically weaving the 1 D CNT and 2D RGO using their intrinsic van der Waals force. The CNT network is beneficial for improving the electronic conductivity of the electrode, while the AC particles could effectively suppress the aggregation of RGO and CNT due to their blocking effect. The synergistic effects among the AC, CNT and RGO validate the AC/CNT/RGO as a promisingmore » electrode for supercapacitor, exhibiting greatly enhanced electrochemical performances in comparison with the pure RGO film, pure CNT film and AC electrode. The AC/CNT/RGO electrode delivers a high specific capacitance of 101 F g-1 at the current density of 0.2 A g-1, offering a maximum energy density of 30.0 W h kg-1 in organic electrolyte at the cut-off voltage range of 0.001~3.0 V. The findings of this work open a new avenue for the design of self-supporting electrodes for the development of flexible and light weight energy storage supercapacitor.« less

Effect of the flexibility training performed immediately before resistance training on muscle hypertrophy, maximum strength and flexibility.

PubMed

Junior, Roberto Moriggi; Berton, Ricardo; de Souza, Thiago Mattos Frota; Chacon-Mikahil, Mara Patrícia Traina; Cavaglieri, Cláudia Regina

2017-04-01

It has been suggested that flexibility training may reduce the total volume of training during resistance trainings. The purpose of this study was to compare the effect of flexibility training immediately before resistance training (FLEX-RT) versus resistance training without flexibility training (RT) on maximum strength and the vastus lateralis muscle cross-sectional area (CSA). Participants had each leg assigned to RT or FLEX-RT. Both groups performed four sets of leg extensions to voluntary failure of 80% of one repetition maximum (1RM); however, FLEX-RT performed two sets of 25 s of static stretching before resistance training. Number of repetitions and total volume were calculated during weeks 1-5 and 6-10. Vastus lateralis muscle CSA, 1RM, and flexibility were assessed at baseline and after 10 weeks. The number of repetitions and total training volume were greater for RT than FLEX-RT for weeks 1-5 and 6-10. Regarding the vastus lateralis muscle CSA, a main time effect was observed, however, greater change was observed for RT than FLEX-RT (12.7 and 7.4%, respectively). A main time effect for 1RM was also observed with similar changes for RT and FLEX-RT (12.7 and 12.9%, respectively). Flexibility was increased pre- to post-training for FLEX-RT with greater change for FLEX-RT (10.1%) than RT (2.1%). These results show that performing flexibility training immediately before resistance training can contribute to a lower number of repetitions, total volume, and muscle hypertrophy.

49 CFR 173.37 - Hazardous Materials in Flexible Bulk Containers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... an external visual inspection by the person filling the Flexible Bulk Container to ensure: (1) The... transported in cargo transport units when offered for transportation by vessel. (7) Flexible Bulk Containers... 49 Transportation 2 2013-10-01 2013-10-01 false Hazardous Materials in Flexible Bulk Containers...

49 CFR 173.37 - Hazardous Materials in Flexible Bulk Containers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... an external visual inspection by the person filling the Flexible Bulk Container to ensure: (1) The... transported in cargo transport units when offered for transportation by vessel. (7) Flexible Bulk Containers... 49 Transportation 2 2014-10-01 2014-10-01 false Hazardous Materials in Flexible Bulk Containers...

An analytical model with flexible accuracy for deep submicron DCVSL cells

NASA Astrophysics Data System (ADS)

Valiollahi, Sepideh; Ardeshir, Gholamreza

2018-07-01

Differential cascoded voltage switch logic (DCVSL) cells are among the best candidates of circuit designers for a wide range of applications due to advantages such as low input capacitance, high switching speed, small area and noise-immunity; nevertheless, a proper model has not yet been developed to analyse them. This paper analyses deep submicron DCVSL cells based on a flexible accuracy-simplicity trade-off including the following key features: (1) the model is capable of producing closed-form expressions with an acceptable accuracy; (2) model equations can be solved numerically to offer higher accuracy; (3) the short-circuit currents occurring in high-low/low-high transitions are accounted in analysis and (4) the changes in the operating modes of transistors during transitions together with an efficient submicron I-V model, which incorporates the most important non-ideal short-channel effects, are considered. The accuracy of the proposed model is validated in IBM 0.13 µm CMOS technology through comparisons with the accurate physically based BSIM3 model. The maximum error caused by analytical solutions is below 10%, while this amount is below 7% for numerical solutions.

Space Launch System (SLS) Safety, Mission Assurance, and Risk Mitigation

NASA Technical Reports Server (NTRS)

May, Todd

2013-01-01

SLS Driving Objectives: I. Safe: a) Human-rated to provide safe and reliable systems for human missions. b) Protecting the public, NASA workforce, high-value equipment and property, and the environment from potential harm. II. Affordable: a) Maximum use of common elements and existing assets, infrastructure, and workforce. b) Constrained budget environment. c) Competitive opportunities for affordability on-ramps. III. Sustainable: a) Initial capability: 70 metric tons (t), 2017-2021. 1) Serves as primary transportation for Orion and exploration missions. 2) Provides back-up capability for crew/cargo to ISS. b) Evolved capability: 105 t and 130 t, post-2021. 1) Offers large volume for science missions and payloads. 2) Modular and flexible, right-sized for mission requirements.

Office-based treatment of vocal fold polyp with flexible laryngosvideostroboscopic surgery.

PubMed

Lan, Ming-Chin; Hsu, Yen-Bin; Chang, Shyue-Yih; Huang, Jui-Lin; Tai, Shyh-Kuan; Chien, Chih-Hung; Chu, Pen-Yuan

2010-02-01

To evaluate the usefulness and safety of flexible laryngovideostroboscopic (FLVS) surgery in patients with vocal fold polyp and to discuss its advantages and limitations in comparison with traditional direct microlaryngoscopic technique under general anesthesia. Retrospective analysis. Twenty patients with vocal fold polyp treated by FLVS surgery under topical anesthesia were reviewed. The results were evaluated by videostroboscopy and grade of the severity of dysphonia, roughness, and breathiness (GRB) scales. Phonatory results, including maximum phonation time, jitter, shimmer, and noise to harmonic ratio, were also reviewed for objective evaluations. All patients completed the surgery smoothly, and seven of them had a higher risk for general anesthesia because of their medical diseases. The procedure was typically accomplished within 20 minutes, and no complications were noted. Videostroboscopy showed improved degree of glottic closure (p < .001), regularity (p = .046), phase symmetry (p = .008), and mucosal wave (p = .008) after FLVS. A significant improvement was noted between preoperative and postoperative results with regard to GRB scale (p < .001, p = .001, and p = .013, respectively). Maximum phonation time also increased significantly after surgery (p = .002). Trivial mucosal residual was noted in one patient. No recurrence was found after a 6-month follow-up period. FLVS surgery is a highly applicable procedure with low invasiveness and minimal morbidity. It offers a simple and cost-effective alternative to the traditional direct microlaryngoscopic procedure, especially for those who are not candidates for general anesthesia or suspension of the larynx.

A star tracker insensitive to stray light generated by radiation sources close to the field of view

NASA Astrophysics Data System (ADS)

Romoli, A.; Gambicorti, L.; Simonetti, F.; Zuccaro Marchi, A.

2017-11-01

Aim of this work is to propose an innovative star tracker, practically insensitive to the radiation coming from the sun or from other strong planetary sources out of (but near) the Field of View. These sources need to be stopped in some way. The classical solution to reject the unwanted radiation is to place a shadow (or baffle) before the star tracker objective. The shadow size depends on the Field of View and on the minimum angle subtended by the source (i.e. the sun) with respect to the optical axis of the star tracker. The lower is this angle the larger is the shadow. Requests for star trackers able to work with the sun as close as possible to the Field of View are increasing, due to the need of maximum mission flexibility. The innovation of this proposed star tracker is conceived by using spatial filtering with a concept complementary to that of coronagraph for sun corona observation, allowing to drastically reduce the size of the shadow. It can also work close to antennas and other part of the platform, which, when illuminated by the sun, become secondary sources capable to blind the star tracker. This kind of accommodation offers three main advantages: no cumbersome shadows (baffle), maximum flexibility in terms of mission profile, less platform location constraints. This new star sensor concept, dated 2007, is now patent pending. Galileo Avionica (now Selex Galileo) is the owner of the patent.

Flexible bottom-gate graphene transistors on Parylene C substrate and the effect of current annealing

PubMed Central

Kim, Hyungsoo; Bong, Jihye; Mikael, Solomon; Kim, Tong June; Williams, Justin C.; Ma, Zhenqiang

2016-01-01

Flexible graphene transistors built on a biocompatible Parylene C substrate would enable active circuitry to be integrated into flexible implantable biomedical devices. An annealing method to improve the performance of a flexible transistor without damaging the flexible substrate is also desirable. Here, we present a fabrication method of a flexible graphene transistor with a bottom-gate coplanar structure on a Parylene C substrate. Also, a current annealing method and its effect on the device performance have been studied. The localized heat generated by the current annealing method improves the drain current, which is attributed to the decreased contact resistance between graphene and S/D electrodes. A maximum current annealing power in the Parylene C-based graphene transistor has been extracted to provide a guideline for an appropriate current annealing. The fabricated flexible graphene transistor shows a field-effect mobility, maximum transconductance, and a Ion/Ioff ratio of 533.5 cm2/V s, 58.1 μS, and 1.76, respectively. The low temperature process and the current annealing method presented here would be useful to fabricate two-dimensional materials-based flexible electronics. PMID:27795570

Simulating Space Capsule Water Landing with Explicit Finite Element Method

NASA Technical Reports Server (NTRS)

Wang, John T.; Lyle, Karen H.

2007-01-01

A study of using an explicit nonlinear dynamic finite element code for simulating the water landing of a space capsule was performed. The finite element model contains Lagrangian shell elements for the space capsule and Eulerian solid elements for the water and air. An Arbitrary Lagrangian Eulerian (ALE) solver and a penalty coupling method were used for predicting the fluid and structure interaction forces. The space capsule was first assumed to be rigid, so the numerical results could be correlated with closed form solutions. The water and air meshes were continuously refined until the solution was converged. The converged maximum deceleration predicted is bounded by the classical von Karman and Wagner solutions and is considered to be an adequate solution. The refined water and air meshes were then used in the models for simulating the water landing of a capsule model that has a flexible bottom. For small pitch angle cases, the maximum deceleration from the flexible capsule model was found to be significantly greater than the maximum deceleration obtained from the corresponding rigid model. For large pitch angle cases, the difference between the maximum deceleration of the flexible model and that of its corresponding rigid model is smaller. Test data of Apollo space capsules with a flexible heat shield qualitatively support the findings presented in this paper.

Rotating flexible drag mill

DOEpatents

Pepper, W.B.

1984-05-09

A rotating parachute for decelerating objects travelling through atmosphere at subsonic or supersonic deployment speeds includes a circular canopy having a plurality of circumferentially arranged flexible panels projecting radially from a solid central disk. A slot extends radially between adjacent panels to the outer periphery of the canopy. Upon deployment, the solid disk diverts air radially to rapidly inflate the panels into a position of maximum diameter. Air impinging on the panels adjacent the panel slots rotates the parachute during its descent. Centrifugal force flattens the canopy into a constant maximum diameter during terminal descent for maximum drag and deceleration.

75 FR 60263 - Federal Acquisition Regulation; Offering a Construction Requirement-8(a) Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-29

... geographical area where the work is to be performed. However, the SBA regulation requires the offering letters... September 30, 1993. This rule is not a major rule under 5 U.S.C. 804. B. Regulatory Flexibility Act The Regulatory Flexibility Act does not apply to this rule. This final rule does not constitute a significant FAR...

A homotopy algorithm for synthesizing robust controllers for flexible structures via the maximum entropy design equations

NASA Technical Reports Server (NTRS)

Collins, Emmanuel G., Jr.; Richter, Stephen

1990-01-01

One well known deficiency of LQG compensators is that they do not guarantee any measure of robustness. This deficiency is especially highlighted when considering control design for complex systems such as flexible structures. There has thus been a need to generalize LQG theory to incorporate robustness constraints. Here we describe the maximum entropy approach to robust control design for flexible structures, a generalization of LQG theory, pioneered by Hyland, which has proved useful in practice. The design equations consist of a set of coupled Riccati and Lyapunov equations. A homotopy algorithm that is used to solve these design equations is presented.

Impact of back squat training intensity on strength and flexibility of hamstring muscle group.

PubMed

Shariat, Ardalan; Lam, Eddie T C; Shaw, Brandon S; Shaw, Ina; Kargarfard, Mehdi; Sangelaji, Bahram

2017-01-01

True experimental design. The back squat is an integral aspect of any resistance training program to improve athletic performance. It is also used for injury prevention of the lower limbs. The purpose of this study was to examine the effect of back squat training at different intensities on strength and flexibility of the hamstring muscle group (HMG). Twenty-two male recreational bodybuilders with at least two years of experience in resistance training were recruited to participate in a nine-week training program. They were randomly assigned to a heavy back squat group (90-95% of one repetition maximum) or a moderate-intensity back squat group (60-65% of one repetition maximum). The heavy back squat group resulted in a significantly (p < 0.001) increased in one repetition maximum strength but a significant (p < 0.001) reduction in HMG flexibility when compared to their counterparts. The results of the study indicate that while a heavy back squat training program is effective in improving strength, it has an adverse effect on the flexibility of the HMG. The implication of this study is that there is a tradeoff between strength and flexibility and trainers should select the appropriate training protocols for their athletes to maximize athletic performance.

Self-supporting activated carbon/carbon nanotube/reduced graphene oxide flexible electrode for high performance supercapacitor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xing; Tang, Yao; Song, Junhua

A self-supporting and flexible activated carbon/carbon nanotube/reduced graphene oxide (AC/CNT/RGO) film has been rationally designed for constructing high-performance supercapacitor. We prepared the AC/CNT/RGO film by anchoring the AC particles with a 3D and porous framework built by hierarchically weaving the 1 D CNT and 2D RGO using their intrinsic van der Waals force. The CNT network is beneficial for improving the electronic conductivity of the electrode, while the AC particles could effectively suppress the aggregation of RGO and CNT due to their blocking effect. The synergistic effects among the AC, CNT and RGO validate the AC/CNT/RGO as a promising electrodemore » for supercapacitor, exhibiting greatly enhanced electrochemical performances in comparison with the pure RGO film, pure CNT film and AC electrode. Furthermore, the AC/CNT/RGO electrode delivers a high specific capacitance of 101 F g -1 at the current density of 0.2 A g -1 offering a maximum energy density of 30.0 W h kg -1 in organic electrolyte at the cut-off voltage range of 0.001–3.0 V. The findings of this work open a new avenue for the design of self-supporting electrodes for the development of flexible and light weight energy storage supercapacitor.« less

Self-supporting activated carbon/carbon nanotube/reduced graphene oxide flexible electrode for high performance supercapacitor

DOE PAGES

Li, Xing; Tang, Yao; Song, Junhua; ...

2017-12-06

A self-supporting and flexible activated carbon/carbon nanotube/reduced graphene oxide (AC/CNT/RGO) film has been rationally designed for constructing high-performance supercapacitor. We prepared the AC/CNT/RGO film by anchoring the AC particles with a 3D and porous framework built by hierarchically weaving the 1 D CNT and 2D RGO using their intrinsic van der Waals force. The CNT network is beneficial for improving the electronic conductivity of the electrode, while the AC particles could effectively suppress the aggregation of RGO and CNT due to their blocking effect. The synergistic effects among the AC, CNT and RGO validate the AC/CNT/RGO as a promising electrodemore » for supercapacitor, exhibiting greatly enhanced electrochemical performances in comparison with the pure RGO film, pure CNT film and AC electrode. Furthermore, the AC/CNT/RGO electrode delivers a high specific capacitance of 101 F g -1 at the current density of 0.2 A g -1 offering a maximum energy density of 30.0 W h kg -1 in organic electrolyte at the cut-off voltage range of 0.001–3.0 V. The findings of this work open a new avenue for the design of self-supporting electrodes for the development of flexible and light weight energy storage supercapacitor.« less

Flexible Applications of the Coping Cat Program for Anxious Youth1

PubMed Central

Beidas, Rinad S.; Benjamin, Courtney L.; Puleo, Connor M.; Edmunds, Julie M.; Kendall, Philip C.

2010-01-01

The current article offers suggestions for ways to adapt empirically supported treatments (ESTs). A specific manualized EST (Coping Cat; Kendall & Hedtke, 2006a) is used to illustrate the concept of “flexibility within fidelity” (Kendall & Beidas, 2007; Kendall, Gosch, Furr, & Sood, 2008). Flexibility within fidelity stresses the importance of using ESTs while considering and taking into account individual client presentations. In this discussion, recommendations are offered for the use of the Coping Cat with younger youth, adolescents, and youth with secondary comorbidities (i.e., social skills deficits, inattentive symptoms, and depressive symptoms). PMID:20936081

Effects of flexibility and aspect ratio on the aerodynamic performance of flapping wings.

PubMed

Fu, Junjiang; Liu, Xiaohui; Shyy, Wei; Qiu, Huihe

2018-03-14

In the current study, we experimentally investigated the flexibility effects on the aerodynamic performance of flapping wings and the correlation with aspect ratio at angle of attack α  =  45°. The Reynolds number based on the chord length and the wing tip velocity is maintained at Re  =  5.3  ×  10 3 . Our result for compliant wings with an aspect ratio of 4 shows that wing flexibility can offer improved aerodynamic performance compared to that of a rigid wing. Flexible wings are found to offer higher lift-to-drag ratios; in particular, there is significant reduction in drag with little compromise in lift. The mechanism of the flexibility effects on the aerodynamic performance is addressed by quantifying the aerodynamic lift and drag forces, the transverse displacement on the wings and the flow field around the wings. The regime of the effective stiffness that offers improved aerodynamic performance is quantified in a range of about 0.5-10 and it matches the stiffness of insect wings with similar aspect ratios. Furthermore, we find that the aspect ratio of the wing is the predominant parameter determining the flexibility effects of compliant wings. Compliant wings with an aspect ratio of two do not demonstrate improved performance compared to their rigid counterparts throughout the entire stiffness regime investigated. The correlation between wing flexibility effects and the aspect ratio is supported by the stiffness of real insect wings.

Path connectivity based spectral defragmentation in flexible bandwidth networks.

PubMed

Wang, Ying; Zhang, Jie; Zhao, Yongli; Zhang, Jiawei; Zhao, Jie; Wang, Xinbo; Gu, Wanyi

2013-01-28

Optical networks with flexible bandwidth provisioning have become a very promising networking architecture. It enables efficient resource utilization and supports heterogeneous bandwidth demands. In this paper, two novel spectrum defragmentation approaches, i.e. Maximum Path Connectivity (MPC) algorithm and Path Connectivity Triggering (PCT) algorithm, are proposed based on the notion of Path Connectivity, which is defined to represent the maximum variation of node switching ability along the path in flexible bandwidth networks. A cost-performance-ratio based profitability model is given to denote the prons and cons of spectrum defragmentation. We compare these two proposed algorithms with non-defragmentation algorithm in terms of blocking probability. Then we analyze the differences of defragmentation profitability between MPC and PCT algorithms.

Multiplexing 200 spatial modes with a single hologram

NASA Astrophysics Data System (ADS)

Rosales-Guzmán, Carmelo; Bhebhe, Nkosiphile; Mahonisi, Nyiku; Forbes, Andrew

2017-11-01

The on-demand tailoring of light's spatial shape is of great relevance in a wide variety of research areas. Computer-controlled devices, such as spatial light modulators (SLMs) or digital micromirror devices, offer a very accurate, flexible and fast holographic means to this end. Remarkably, digital holography affords the simultaneous generation of multiple beams (multiplexing), a tool with numerous applications in many fields. Here, we provide a self-contained tutorial on light beam multiplexing. Through the use of several examples, the readers will be guided step by step in the process of light beam shaping and multiplexing. Additionally, we provide a quantitative analysis on the multiplexing capabilities of SLMs to assess the maximum number of beams that can be multiplexed on a single SLM, showing approximately 200 modes on a single hologram.

Flexible Pedagogies: New Pedagogical Ideas. Flexible Pedagogies: Preparing for the Future Series

ERIC Educational Resources Information Center

Ryan, Alex; Tilbury, Daniella

2014-01-01

This publication is part of our five-strand research project "Flexible Pedagogies: preparing for the future". It identifies six "new pedagogical ideas" offering new pathways for learning. These include: (1) actively involving students in learning development and processes of "co-creation" thereby challenging existing…

Working Hours Flexibility. Background Paper No. 30.

ERIC Educational Resources Information Center

Staines, Graham L.

Flexible work schedules offer the promise of a low-cost option for helping people manage work and family responsibilities. Alternative work schedules include part-time work, job sharing, work sharing, shiftwork, compressed work week, flexitime, and flexiplace. Flexitime is the most prevalent full-time flexible schedule and is second in prevalence…

Analysis to determine the maximum dimensions of flexible apertures in sensored security netting products.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murton, Mark; Bouchier, Francis A.; vanDongen, Dale T.

2013-08-01

Although technological advances provide new capabilities to increase the robustness of security systems, they also potentially introduce new vulnerabilities. New capability sometimes requires new performance requirements. This paper outlines an approach to establishing a key performance requirement for an emerging intrusion detection sensor: the sensored net. Throughout the security industry, the commonly adopted standard for maximum opening size through barriers is a requirement based on square inchestypically 96 square inches. Unlike standard rigid opening, the dimensions of a flexible aperture are not fixed, but variable and conformable. It is demonstrably simple for a human intruder to move through a 96-square-inchmore » opening that is conformable to the human body. The longstanding 96-square-inch requirement itself, though firmly embedded in policy and best practice, lacks a documented empirical basis. This analysis concluded that the traditional 96-square-inch standard for openings is insufficient for flexible openings that are conformable to the human body. Instead, a circumference standard is recommended for these newer types of sensored barriers. The recommended maximum circumference for a flexible opening should be no more than 26 inches, as measured on the inside of the netting material.« less

Freestanding NiFe Oxyfluoride Holey Film with Ultrahigh Volumetric Capacitance for Flexible Asymmetric Supercapacitors.

PubMed

Liang, Kun; Marcus, Kyle; Yang, Zhenzhong; Zhou, Le; Pan, Hao; Bai, Yuanli; Du, Yingge; Engelhard, Mark H; Yang, Yang

2018-01-01

In this work, a freestanding NiFe oxyfluoride (NiFeOF) holey film is prepared by electrochemical deposition and anodic treatments. With the combination of good electrical conductivity and holey structure, the NiFeOF holey film offers superior electrochemical performance with maximum specific capacitance of 670 F cm -3 (134 mF cm -2 ), due to the following reasons: (i) The residual metal alloy framework can be used as the current collector to improve electrode conductivity. Moreover, the as-prepared freestanding NiFeOF holey film can be used as a supercapacitor electrode without reliance on binders and other additives. The residual metal alloy framework and binder-free electrode effectively reduce electrode resistance, thus improving electron transport. (ii) The highly interconnected holey structure and hierarchical pore distribution provide a high specific surface area to improve electron transport, enhancing rapid ion transport, and mitigating diffusion limitations throughout the holey film. (iii) The excellent mechanical characteristics facilitate flexibility and cyclability related performance. Additionally, the NiFeOF holey film presents exceptional electrochemical performance, showing that it is a promising alternative for small/microsize electronic devices. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Contagious flexibility? A study on whether schedule flexibility facilitates work-life enrichment.

PubMed

Pedersen, Vivi Bach; Jeppesen, Hans Jeppe

2012-08-01

Schedule flexibility defines an important generating resource for work-life enrichment; however, our knowledge about how such spillovers take place is limited. This multiple case study examines how workers from different working time contexts with varying levels of schedule flexibility experience work-life interplay. Given the adopted explorative design, it is important to interpret the findings in a tentative light. Nonetheless, the study offers important insight into work-life enrichment that may guide future research in this field. The findings indicate that schedule flexibility may act as a boundary-spanning resource owing to the agency potential it offers workers. Thus, it seemed that flexible schedule opportunities enabled workers to engage more fully in personal life activities, which in turn had a positive influence on their work involvement through positive affect. Such positive role engagements appeared, however, to be greatly determined by workers' boundary management and by time conditions of work and family. In conclusion, the major findings and limitation of the study are discussed against existing research and theory. © 2012 The Authors. Scandinavian Journal of Psychology © 2012 The Scandinavian Psychological Associations.

Stress analysis in a pedicle screw fixation system with flexible rods in the lumbar spine.

PubMed

Kim, Kyungsoo; Park, Won Man; Kim, Yoon Hyuk; Lee, SuKyoung

2010-01-01

Breakage of screws has been one of the most common complications in spinal fixation systems. However, no studies have examined the breakage risk of pedicle screw fixation systems that use flexible rods, even though flexible rods are currently being used for dynamic stabilization. In this study, the risk of breakage of screws for the rods with various flexibilities in pedicle screw fixation systems is investigated by calculating the von Mises stress as a breakage risk factor using finite element analysis. Three-dimensional finite element models of the lumbar spine with posterior one-level spinal fixations at L4-L5 using four types of rod (a straight rod, a 4 mm spring rod, a 3 mm spring rod, and a 2 mm spring rod) were developed. The von Mises stresses in both the pedicle screws and the rods were analysed under flexion, extension, lateral bending, and torsion moments of 10 Nm with a follower load of 400 N. The maximum von Mises stress, which was concentrated on the neck region of the pedicle screw, decreased as the flexibility of the rod increased. However, the ratio of the maximum stress in the rod to the yield stress increased substantially when a highly flexible rod was used. Thus, the level of rod flexibility should be considered carefully when using flexible rods for dynamic stabilization because the intersegmental motion facilitated by the flexible rod results in rod breakage.

9 CFR 318.303 - Critical factors and the application of the process schedule.

Code of Federal Regulations, 2010 CFR

2010-01-01

... container; (3) Container orientation during thermal processing; (4) Product formulation; (5) Particle size; (6) Maximum thickness for flexible, and to some extent semirigid containers during thermal processing; (7) Maximum pH; (8) Percent salt; (9) Ingoing (or formulated) nitrite level (ppm); (10) Maximum water...

Can flexibility help you float?

NASA Astrophysics Data System (ADS)

Burton, L. J.; Bush, J. W. M.

2012-10-01

We consider the role of flexibility in the weight-bearing characteristics of bodies floating at an interface. Specifically, we develop a theoretical model for a two-dimensional thin floating plate that yields the maximum stable plate load and optimal stiffness for weight support. Plates small relative to the capillary length are primarily supported by surface tension, and their weight-bearing potential does not benefit from flexibility. Above a critical size comparable to the capillary length, flexibility assists interfacial flotation. For plates on the order of and larger than the capillary length, deflection from an initially flat shape increases the force resulting from hydrostatic pressure, allowing the plate to support a greater load. In this large plate limit, the shape that bears the most weight is a semicircle, which displaces the most fluid above the plate for a fixed plate length. Exact results for maximum weight-bearing plate shapes are compared to analytic approximations made in the limits of large and small plate sizes. The value of flexibility for floating to a number of biological organisms is discussed in light of our study.

Wired Widgets: Agile Visualization for Space Situational Awareness

NASA Astrophysics Data System (ADS)

Gerschefske, K.; Witmer, J.

2012-09-01

Continued advancement in sensors and analysis techniques have resulted in a wealth of Space Situational Awareness (SSA) data, made available via tools and Service Oriented Architectures (SOA) such as those in the Joint Space Operations Center Mission Systems (JMS) environment. Current visualization software cannot quickly adapt to rapidly changing missions and data, preventing operators and analysts from performing their jobs effectively. The value of this wealth of SSA data is not fully realized, as the operators' existing software is not built with the flexibility to consume new or changing sources of data or to rapidly customize their visualization as the mission evolves. While tools like the JMS user-defined operational picture (UDOP) have begun to fill this gap, this paper presents a further evolution, leveraging Web 2.0 technologies for maximum agility. We demonstrate a flexible Web widget framework with inter-widget data sharing, publish-subscribe eventing, and an API providing the basis for consumption of new data sources and adaptable visualization. Wired Widgets offers cross-portal widgets along with a widget communication framework and development toolkit for rapid new widget development, giving operators the ability to answer relevant questions as the mission evolves. Wired Widgets has been applied in a number of dynamic mission domains including disaster response, combat operations, and noncombatant evacuation scenarios. The variety of applications demonstrate that Wired Widgets provides a flexible, data driven solution for visualization in changing environments. In this paper, we show how, deployed in the Ozone Widget Framework portal environment, Wired Widgets can provide an agile, web-based visualization to support the SSA mission. Furthermore, we discuss how the tenets of agile visualization can generally be applied to the SSA problem space to provide operators flexibility, potentially informing future acquisition and system development.

Note: Design and capability verification of fillet triangle flexible support

NASA Astrophysics Data System (ADS)

Wang, Tao; San, Xiao-Gang; Gao, Shi-Jie; Wang, Jing; Ni, Ying-Xue; Sang, Zhi-Xin

2017-12-01

By increasing the section thickness of a triangular flexible hinge, this study focuses on optimal selection of parameters of fillet triangle flexible hinges and flexible support. Based on Castigliano's second theorem, the flexibility expression of the fillet triangle flexible hinge was derived. Then, the case design is performed, and the comparison of three types of flexible hinges with this type of flexible hinge was carried out. The finite element models of fillet triangle flexible hinges and flexible support were built, and then the simulation results of performance parameters were calculated. Finally, the experiment platform was established to validate analysis results. The maximum error is less than 8%, which verifies the accuracy of the simulation process and equations derived; also the fundamental frequency fits the requirements of the system. The fillet triangle flexible hinge is proved to have the advantages of high precision and low flexibility.

Note: Design and capability verification of fillet triangle flexible support.

PubMed

Wang, Tao; San, Xiao-Gang; Gao, Shi-Jie; Wang, Jing; Ni, Ying-Xue; Sang, Zhi-Xin

2017-12-01

By increasing the section thickness of a triangular flexible hinge, this study focuses on optimal selection of parameters of fillet triangle flexible hinges and flexible support. Based on Castigliano's second theorem, the flexibility expression of the fillet triangle flexible hinge was derived. Then, the case design is performed, and the comparison of three types of flexible hinges with this type of flexible hinge was carried out. The finite element models of fillet triangle flexible hinges and flexible support were built, and then the simulation results of performance parameters were calculated. Finally, the experiment platform was established to validate analysis results. The maximum error is less than 8%, which verifies the accuracy of the simulation process and equations derived; also the fundamental frequency fits the requirements of the system. The fillet triangle flexible hinge is proved to have the advantages of high precision and low flexibility.

Goal driven kinematic simulation of flexible arm robot for space station missions

NASA Technical Reports Server (NTRS)

Janssen, P.; Choudry, A.

1987-01-01

Flexible arms offer a great degree of flexibility in maneuvering in the space environment. The problem of transporting an astronaut for extra-vehicular activity using a space station based flexible arm robot was studied. Inverse kinematic solutions of the multilink structure were developed. The technique is goal driven and can support decision making for configuration selection as required for stability and obstacle avoidance. Details of this technique and results are given.

Tunable inter-qubit coupling as a resource for gate based quantum computing with superconducting circuits

NASA Astrophysics Data System (ADS)

Chiaro, B.; Neill, C.; Chen, Z.; Dunsworth, A.; Foxen, B.; Quintana, C.; Wenner, J.; Martinis, J. M.; Google Quantum Hardware Team

Fast, high fidelity two qubit gates are an essential requirement of a quantum processor. In this talk, we discuss how the tunable coupling of the gmon architecture provides a pathway for an improved two qubit controlled-Z gate. The maximum inter-qubit coupling strength gmax = 60 MHz is sufficient for fast adiabatic two qubit gates to be performed as quickly as single qubit gates, reducing dephasing errors. Additionally, the ability to turn the coupling off allows all qubits to idle at low magnetic flux sensitivity, further reducing susceptibility to noise. However, the flexibility that this platform offers comes at the expense of increased control complexity. We describe our strategy for addressing the control challenges of the gmon architecture and show experimental progress toward fast, high fidelity controlled-Z gates with gmon qubits.

Hyperswitch communication network

NASA Technical Reports Server (NTRS)

Peterson, J.; Pniel, M.; Upchurch, E.

1991-01-01

The Hyperswitch Communication Network (HCN) is a large scale parallel computer prototype being developed at JPL. Commercial versions of the HCN computer are planned. The HCN computer being designed is a message passing multiple instruction multiple data (MIMD) computer, and offers many advantages in price-performance ratio, reliability and availability, and manufacturing over traditional uniprocessors and bus based multiprocessors. The design of the HCN operating system is a uniquely flexible environment that combines both parallel processing and distributed processing. This programming paradigm can achieve a balance among the following competing factors: performance in processing and communications, user friendliness, and fault tolerance. The prototype is being designed to accommodate a maximum of 64 state of the art microprocessors. The HCN is classified as a distributed supercomputer. The HCN system is described, and the performance/cost analysis and other competing factors within the system design are reviewed.

Efficient, adaptive estimation of two-dimensional firing rate surfaces via Gaussian process methods.

PubMed

Rad, Kamiar Rahnama; Paninski, Liam

2010-01-01

Estimating two-dimensional firing rate maps is a common problem, arising in a number of contexts: the estimation of place fields in hippocampus, the analysis of temporally nonstationary tuning curves in sensory and motor areas, the estimation of firing rates following spike-triggered covariance analyses, etc. Here we introduce methods based on Gaussian process nonparametric Bayesian techniques for estimating these two-dimensional rate maps. These techniques offer a number of advantages: the estimates may be computed efficiently, come equipped with natural errorbars, adapt their smoothness automatically to the local density and informativeness of the observed data, and permit direct fitting of the model hyperparameters (e.g., the prior smoothness of the rate map) via maximum marginal likelihood. We illustrate the method's flexibility and performance on a variety of simulated and real data.

Flexible Photodetectors Based on 1D Inorganic Nanostructures

PubMed Central

Lou, Zheng

2015-01-01

Flexible photodetectors with excellent flexibility, high mechanical stability and good detectivity, have attracted great research interest in recent years. 1D inorganic nanostructures provide a number of opportunities and capabilities for use in flexible photodetectors as they have unique geometry, good transparency, outstanding mechanical flexibility, and excellent electronic/optoelectronic properties. This article offers a comprehensive review of several types of flexible photodetectors based on 1D nanostructures from the past ten years, including flexible ultraviolet, visible, and infrared photodetectors. High‐performance organic‐inorganic hybrid photodetectors, as well as devices with 1D nanowire (NW) arrays, are also reviewed. Finally, new concepts of flexible photodetectors including piezophototronic, stretchable and self‐powered photodetectors are examined to showcase the future research in this exciting field. PMID:27774404

Flexible Fe3O4@Carbon Nanofibers Hierarchically Assembled with MnO2 Particles for High-Performance Supercapacitor Electrodes.

PubMed

Iqbal, Nousheen; Wang, Xianfeng; Babar, Aijaz Ahmed; Zainab, Ghazala; Yu, Jianyong; Ding, Bin

2017-11-09

Increasing use of wearable electronic devices have resulted in enhanced demand for highly flexible supercapacitor electrodes with superior electrochemical performance. In this study, flexible composite membranes with electrosprayed MnO 2 particles uniformly anchored on Fe 3 O 4 doped electrospun carbon nanofibers (Fe 3 O 4 @CNF Mn ) have been prepared as flexible electrodes for high-performance supercapacitors. The interconnected porous beaded structure ensures free movement of electrolyte within the composite membranes, therefore, the developed supercapacitor electrodes not only offer high specific capacitance of ~306 F/g, but also exhibit good capacitance retention of ~85% after 2000 cycles, which certify that the synthesized electrodes offer high and stable electrochemical performance. Additionally, the supercapacitors fabricated from our developed electrodes well maintain their performance under flexural stress and exhibit a very minute change in specific capacitance even up to 180° bending angle. The developed electrode fabrication strategy integrating electrospinning and electrospray techniques paves new insights into the development of potential functional nanofibrous materials for light weight and flexible wearable supercapacitors.

Improved design of support for large aperture space lightweight mirror

NASA Astrophysics Data System (ADS)

Wang, Chao; Ruan, Ping; Liu, Qimin

2013-08-01

In order to design a kind of rational large aperture space mirror which can adapt to the space gravity and thermal environment, by taking the choice of material, the lightweight of the mirror and the design of support into account in detail, a double-deck structure with traditional flexible hinge was designed, then the analytical mathematical model of the mirror system was established. The design adopts six supports on back. in order to avoid the constraints, mirror is connected to three middle transition pieces through six flexible hinges, and then the three transition pieces are connected to support plate through another three flexible hinges. However, the initial structure is unable to reach the expected design target and needs to be made further adjustments. By improving and optimizing the original structure, a new type of flexible hinge in the shape of the letter A is designed finally. Compared with the traditional flexible hinge structure, the new structure is simpler and has less influence on the surface figure accuracy of mirror. By using the finite element analysis method, the static and dynamic characteristics as well as the thermal characteristics of the mirror system are analyzed. Analysis results show that the maximum PV value is 37 nm and the maximum RMS value is 10.4 nm when gravity load is applied. Furthermore, the maximum PV value is 46 nm and the maximum RMS value is 10.5 nm under the load case of gravity coupled with 4℃ uniform temperature rise. The results satisfy the index of optical design. The first order natural frequency of the mirror component is 130 Hz according to the conclusion obtained by modal analytical solution, so the mirror structure has high enough fundamental frequency. And, the structural strength can meet the demand under the overload and the random vibration environment respectively. It indicates that the mirror component structure has enough dynamic, static stiffness and thermal stability, meeting the design requirements.

High-performance flexible all-solid-state supercapacitors based on densely-packed graphene/polypyrrole nanoparticle papers

NASA Astrophysics Data System (ADS)

Yang, Chao; Zhang, Liling; Hu, Nantao; Yang, Zhi; Wei, Hao; Wang, Yanyan; Zhang, Yafei

2016-11-01

Graphene-based all-solid-state supercapacitors (ASSSCs) have received increasing attention. It's a great challenge to fabricate high-performance flexible solid-state supercapacitors with high areal and volumetric energy storage capability, superior electron and ion conductivity, robust mechanical flexibility, as well as long term stability. Herein, we report a facile method to fabricate flexible ASSSCs based on densely-packed reduced graphene oxide (rGO)/polypyrrole nanoparticle (PPy NP) hybrid papers with a sandwich framework, which consists of well-separated and continuously-aligned rGO sheets. The incorporation of PPy NPs not only provides pseudocapacitance but also facilitates the infiltration of gel electrolyte. The assembled ASSSCs possess maximum areal and volumetric specific capacitances of 477 mF/cm2 and 94.9 F/cm3 at 0.5 mA/cm2. They also exhibit little capacitance deviation under different bending states, excellent cycling stability, small leakage current and low self-discharge characteristics. Additionally, the maximum areal and volumetric energy densities of 132.5 μWh/cm2 and 26.4 mWh/cm3 are achieved, which indicate that this hybrid paper is a promising candidate for high-performance flexible energy storage devices.

Low-frequency and wideband vibration energy harvester with flexible frame and interdigital structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Pengwei, E-mail: lipengwei@tyut.edu.cn; Wang, Yanfen; Luo, Cuixian

2015-04-15

As an alternative to traditional cantilever beam structures and their evolutions, a flexible beam based, interdigital structure, vibration energy harvester has been presented and investigated. The proposed interdigital-shaped oscillator consists of a rectangular flexible frame and series of cantilever beams interdigitally bonded to it. In order to achieve low frequency and wide-bandwidth harvesting, Young’s modulus of materials, frame size and the amount of the cantilevers have been studied systematically. The measured frequency responses of the designed device (PDMS frame, quintuple piezoelectric cantilever beams) show a 460% increase in bandwidth below 80Hz. When excited at an acceleration of 1.0 g, themore » energy harvester achieves to a maximum open-circuit voltage of 65V, and the maximum output power 4.5 mW.« less

DESIGNS FOR SMALL HIGH SCHOOLS.

ERIC Educational Resources Information Center

NIMNICHT, GLENDON P.; PARTRIDGE, ARTHUR R.

BY MULTIPLE-CLASS TEACHING AND FLEXIBLE SCHEDULING, SMALL HIGH SCHOOLS CAN OFFER EDUCATIONAL PROGRAMS COMPARABLE TO THOSE OFFERED BY LARGE HIGH SCHOOLS. WITH ATTENTION TO FACILITY DESIGN, NOT ONLY CAN SCIENCE, MATHEMATICS, FOREIGN LANGUAGE, ART, BUSINESS, INDUSTRIAL ARTS, HOMEMAKING, ENGLISH, AND SOCIAL STUDIES BE OFFERED TO TWO OR MORE GROUPS OF…

Global identification of stochastic dynamical systems under different pseudo-static operating conditions: The functionally pooled ARMAX case

NASA Astrophysics Data System (ADS)

Sakellariou, J. S.; Fassois, S. D.

2017-01-01

The identification of a single global model for a stochastic dynamical system operating under various conditions is considered. Each operating condition is assumed to have a pseudo-static effect on the dynamics and be characterized by a single measurable scheduling variable. Identification is accomplished within a recently introduced Functionally Pooled (FP) framework, which offers a number of advantages over Linear Parameter Varying (LPV) identification techniques. The focus of the work is on the extension of the framework to include the important FP-ARMAX model case. Compared to their simpler FP-ARX counterparts, FP-ARMAX models are much more general and offer improved flexibility in describing various types of stochastic noise, but at the same time lead to a more complicated, non-quadratic, estimation problem. Prediction Error (PE), Maximum Likelihood (ML), and multi-stage estimation methods are postulated, and the PE estimator optimality, in terms of consistency and asymptotic efficiency, is analytically established. The postulated estimators are numerically assessed via Monte Carlo experiments, while the effectiveness of the approach and its superiority over its FP-ARX counterpart are demonstrated via an application case study pertaining to simulated railway vehicle suspension dynamics under various mass loading conditions.

Graphene Inks with Cellulosic Dispersants: Development and Applications for Printed Electronics

NASA Astrophysics Data System (ADS)

Secor, Ethan Benjamin

Graphene offers promising opportunities for applications in printed and flexible electronic devices due to its high electrical and thermal conductivity, mechanical flexibility and strength, and chemical and environmental stability. However, scalable production and processing of graphene presents a critical technological challenge preventing the application of graphene for flexible electronic interconnects, electrochemical energy storage, and chemically robust electrical contacts. In this thesis, a promising and versatile platform for the production, patterning, and application of graphene inks is presented based on cellulosic dispersants. Graphene is produced from flake graphite using scalable liquid-phase exfoliation methods, using the polymers ethyl cellulose and nitrocellulose as multifunctional dispersing agents. These cellulose derivatives offer high colloidal stability and broadly tunable rheology for graphene dispersions, providing an effective and tunable platform for graphene ink development. Thermal or photonic annealing decomposes the polymer dispersant to yield high conductivity, flexible graphene patterns for various electronics applications. In particular, the chemical stability of graphene enables robust electrical contacts for ceramic, metallic, organic and electrolytic materials, validating the diverse applicability of graphene in printed electronics. Overall, the strategy for graphene ink design presented here offers a simple, efficient, and versatile method for integrating graphene in a wide range of printed devices and systems, providing both fundamental insight for nanomaterial ink development and realistic opportunities for practical applications.

Highly Flexible Hybrid CMOS Inverter Based on Si Nanomembrane and Molybdenum Disulfide.

PubMed

Das, Tanmoy; Chen, Xiang; Jang, Houk; Oh, Il-Kwon; Kim, Hyungjun; Ahn, Jong-Hyun

2016-11-01

2D semiconductor materials are being considered for next generation electronic device application such as thin-film transistors and complementary metal-oxide-semiconductor (CMOS) circuit due to their unique structural and superior electronics properties. Various approaches have already been taken to fabricate 2D complementary logics circuits. However, those CMOS devices mostly demonstrated based on exfoliated 2D materials show the performance of a single device. In this work, the design and fabrication of a complementary inverter is experimentally reported, based on a chemical vapor deposition MoS 2 n-type transistor and a Si nanomembrane p-type transistor on the same substrate. The advantages offered by such CMOS configuration allow to fabricate large area wafer scale integration of high performance Si technology with transition-metal dichalcogenide materials. The fabricated hetero-CMOS inverters which are composed of two isolated transistors exhibit a novel high performance air-stable voltage transfer characteristic with different supply voltages, with a maximum voltage gain of ≈16, and sub-nano watt power consumption. Moreover, the logic gates have been integrated on a plastic substrate and displayed reliable electrical properties paving a realistic path for the fabrication of flexible/transparent CMOS circuits in 2D electronics. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fuel, environmental, and transmission pricing considerations in a deregulated environment

NASA Astrophysics Data System (ADS)

Obessis, Emmanouil Vlassios

The 1992 National Energy Policy Act drastically changed the traditional structure of the vertically integrated utility. To facilitate increased competition in the power utility sector, all markets related to power generation have been opened to free competition and trading. To survive in the new competitive environment, power producers need to reduce costs and increase efficiency. Fuel marketing strategies are thus, getting more aggressive and fuel markets are becoming more competitive, offering more options regarding fuel supplies and contracts. At the same time, the 1990 Clean Air Act Amendments are taking effect. Although tightening the emission standards, this legislation offers utilities a wider flexibility in choosing compliance strategies. It also set maximum annual allowable levels replacing the traditional uniform maximum emission rates. The bill also introduced the concept of marketable emission allowances and provided for the establishment of nationwide markets where allowances may be traded, sold, or purchased. Several fuel- and emission-constrained algorithms have been historically presented, but those two classes of constraints, in general, were handled independently. The multiobjective optimization model developed in this research work, concurrently satisfies sets of detailed fuel and emission limits, modeling in a more accurate way the fuel supply and environmental limitations and their complexities in the new deregulated operational environment. Development of the implementation software is an integral part of this research project. This software may be useful for both daily scheduling activities and short-term operational planning. A Lagrangian multipliers-based variant is used to solve the problem. Single line searches are used to update the multipliers, thus offering attractive execution times. This work also investigates the applicability of cooperative games to the problem of transmission cost allocation. Interest in game theory as a powerful tool to solve common property allocation problems has been renewed. A simple allocation framework is developed using capacity based costing rules. Different solution concepts are applied to solve small scale transmission pricing problems. Game models may render themselves useful in investigating "what if" scenarios.

Maximum likelihood estimation and EM algorithm of Copas-like selection model for publication bias correction.

PubMed

Ning, Jing; Chen, Yong; Piao, Jin

2017-07-01

Publication bias occurs when the published research results are systematically unrepresentative of the population of studies that have been conducted, and is a potential threat to meaningful meta-analysis. The Copas selection model provides a flexible framework for correcting estimates and offers considerable insight into the publication bias. However, maximizing the observed likelihood under the Copas selection model is challenging because the observed data contain very little information on the latent variable. In this article, we study a Copas-like selection model and propose an expectation-maximization (EM) algorithm for estimation based on the full likelihood. Empirical simulation studies show that the EM algorithm and its associated inferential procedure performs well and avoids the non-convergence problem when maximizing the observed likelihood. © The Author 2017. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Design consideration for a nuclear electric propulsion system

NASA Technical Reports Server (NTRS)

Phillips, W. M.; Pawlik, E. V.

1978-01-01

A study is currently underway to design a nuclear electric propulsion vehicle capable of performing detailed exploration of the outer-planets. Primary emphasis is on the power subsystem. Secondary emphasis includes integration into a spacecraft, and integration with the thrust subsystem and science package or payload. The results of several design iterations indicate an all-heat-pipe system offers greater reliability, elimination of many technology development areas and a specific weight of under 20 kg/kWe at the 400 kWe power level. The system is compatible with a single Shuttle launch and provides greater safety than could be obtained with designs using pumped liquid metal cooling. Two configurations, one with the reactor and power conversion forward on the spacecraft with the ion engines aft and the other with reactor, power conversion and ion engines aft were selected as dual baseline designs based on minimum weight, minimum required technology development and maximum growth potential and flexibility.

The Year Ahead: Will Distance Education Enter the Mainstream?

ERIC Educational Resources Information Center

Saba, Farhad, Ed.

1998-01-01

Discusses the following indicators for measuring success in mainstreaming distance education in higher education: integration, resulting in funding and credit for off-campus students; course ownership, providing legal protection for faculty; product differentiation among institutions in course offerings, quality, and flexibility; flexible time…

Study of clathrate hydrates via equilibrium molecular-dynamics simulation employing polarisable and non-polarisable, rigid and flexible water models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burnham, Christian J., E-mail: christian.burnham@ucd.ie, E-mail: niall.english@ucd.ie; English, Niall J., E-mail: christian.burnham@ucd.ie, E-mail: niall.english@ucd.ie

Equilibrium molecular-dynamics (MD) simulations have been performed on metastable sI and sII polymorphs of empty hydrate lattices, in addition to liquid water and ice Ih. The non-polarisable TIP4P-2005, simple point charge model (SPC), and polarisable Thole-type models (TTM): TTM2, TTM3, and TTM4 water models were used in order to survey the differences between models and to see what differences can be expected when polarisability is incorporated. Rigid and flexible variants were used of each model to gauge the effects of flexibility. Power spectra are calculated and compared to density-of-states spectra inferred from inelastic neutron scattering (INS) measurements. Thermodynamic properties weremore » also calculated, as well as molecular-dipole distributions. It was concluded that TTM models offer optimal fidelity vis-à-vis INS spectra, together with thermodynamic properties, with the flexible TTM2 model offering optimal placement of vibrational modes.« less

78 FR 1799 - Next Generation 911; Text-to-911; Next Generation 911 Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-09

... that service providers who offer SMS-based text-to-911 should have the flexibility to migrate their... (a T-Mobile affiliate that offers regional wireless communications service), to provide text-to-911... signatory carrier begins to offer text-to- 911 service, ``valid PSAP requests for Text-to-911 service will...

High-Performance Clock Synchronization Algorithms for Distributed Wireless Airborne Computer Networks with Applications to Localization and Tracking of Targets

DTIC Science & Technology

2010-06-01

GMKPF represents a better and more flexible alternative to the Gaussian Maximum Likelihood (GML), and Exponential Maximum Likelihood ( EML ...accurate results relative to GML and EML when the network delays are modeled in terms of a single non-Gaussian/non-exponential distribution or as a...to the Gaussian Maximum Likelihood (GML), and Exponential Maximum Likelihood ( EML ) estimators for clock offset estimation in non-Gaussian or non

75 FR 59711 - Audit Program for Texas Flexible Permit Holders

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-28

... ENVIRONMENTAL PROTECTION AGENCY [EPA-R06-OAR-2010-0510; FRL-9207-4] Audit Program for Texas... Act (CAA) voluntary audit compliance program for flexible permit holders in the State of Texas (hereinafter ``Audit Program''); response to public comments. SUMMARY: EPA is offering holders of Texas...

Do flexible work policies improve parents' health? A natural experiment based on the UK Millennium Cohort Study.

PubMed

Avendano, Mauricio; Panico, Lidia

2018-03-01

There is limited evidence of the impact of policies to promote work-family balance on family health. Exploiting the introduction of the UK Flexible Working Act (2003), we examined whether a policy that grants parents the right to request flexible work influences their health and well-being. Using the UK Millennium Cohort Study, we focus on 6424 mothers employed in 2001-2002, when the cohort child was 9 months old, until their child's seventh birthday. We used a difference-in-differences (DiD) approach to compare changes in outcomes before and after the policy among mothers most likely to benefit and mothers unlikely to benefit from the policy. Flexible working increased in a small group of mothers (n=548) whose employer did not offer work flexibility before the reform (treatment group). By contrast, among mothers whose employer already offered flexible work before the reform (control group, n=5810), there was little change or a slight decline in flexible working. DiD estimates suggest that the policy was associated with an increase in flexible working (37.5 percentage points, 95% CI 32.9 to 41.6), but it had no impact on self-rated health (-1.6 percentage points, 95% CI -4.4 to 1.1), long-term illness (-1.87 percentage points, 95% CI -4.3 to 0.5) or life satisfaction scores (β=0.04, 95% CI -0.08 to 0.16). The Flexible Working Act increased flexible working only among a small group of mothers who had not yet the right to request work flexibility, but it had no impact on their health and well-being. Policies promoting work flexibility may require stronger incentives for both parents and employers. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Flexible all-solid-state supercapacitors based on polyaniline orderly nanotubes array.

PubMed

Li, Huihua; Song, Juan; Wang, Linlin; Feng, Xiaomiao; Liu, Ruiqing; Zeng, Wenjin; Huang, Zhendong; Ma, Yanwen; Wang, Lianhui

2017-01-07

Flexible all-solid-state supercapacitors are crucial to meet the growing needs for portable electronic devices such as foldable phones and wearable electronics. As promising candidates for pseudocapacitor electrode materials, polyaniline (PANI) orderly nanotube arrays are prepared via a simple template electrodeposition method. The structures of the final product were characterized using various characterization techniques, including scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS). The obtained PANI nanotube film could be directly used as a flexible all-solid-state supercapacitor electrode. Electrochemical results show that the areal capacitance of a PANI nanotube-based supercapacitor with the deposition cycle number of 100 can achieve a maximum areal capacitance of 237.5 mF cm -2 at a scan rate of 10 mV s -1 and maximum energy density of 24.31 mW h cm -2 at a power density of 2.74 mW cm -2 . In addition, the prepared supercapacitor exhibits excellent flexibility under different bending conditions. It retains 95.2% of its initial capacitance value after 2000 cycles at a current density of 1.0 mA cm -1 , which displays its superior cycling stability. Moreover, the prepared flexible all-solid-state supercapacitor can power a light-emitting-diode (LED), which meets the practical applications of micropower supplies.

Flexible, planar-integrated, all-solid-state fiber supercapacitors with an enhanced distributed-capacitance effect.

PubMed

Liu, Bin; Tan, Dongsheng; Wang, Xianfu; Chen, Di; Shen, Guozhen

2013-06-10

Flexible and highly efficient energy storage units act as one of the key components in portable electronics. In this work, by planar-integrated assembly of hierarchical ZnCo₂O₄ nanowire arrays/carbon fibers electrodes, a new class of flexible all-solid-state planar-integrated fiber supercapacitors are designed and produced via a low-cost and facile method. The as-fabricated flexible devices exhibit high-efficiency, enhanced capacity, long cycle life, and excellent electrical stability. An enhanced distributed-capacitance effect is experimentally observed for the device. This strategy enables highly flexible new structured supercapacitors with maximum functionality and minimized size, thus making it possible to be readily applied in flexible/portable photoelectronic devices. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microporous Ni₁₁(HPO₃)₈(OH)₆ nanocrystals for high-performance flexible asymmetric all solid-state supercapacitors.

PubMed

Gao, Yanping; Zhao, Junhong; Run, Zhen; Zhang, Guangqin; Pang, Huan

2014-12-07

Microporous nickel phosphite [Ni11(HPO3)8(OH)6] nanocrystals were prepared using a hydrothermal method, and were successfully applied as a positive electrode in a flexible all solid-state asymmetric supercapacitor. Because of the specific micro/nanostructure, the flexible solid-state asymmetric supercapacitor can achieve a maximum energy density of 0.45 mW h cm(-3), which is higher than most reported supercapacitors. More importantly, the device performance remains efficient for 10,000 cycles.

Response of long, flexible cantilever beams applied root motions. [spacecraft structures

NASA Technical Reports Server (NTRS)

Fralich, R. W.

1976-01-01

Results are presented for an analysis of the response of long, flexible cantilever beams to applied root rotational accelerations. Maximum values of deformation, slope, bending moment, and shear are found as a function of magnitude and duration of acceleration input. Effects of tip mass and its eccentricity and rotatory inertia on the response are also investigated. It is shown that flexible beams can withstand large root accelerations provided the period of applied acceleration can be kept small relative to the beam fundamental period.

SAFE (strategy, assessment, flexibility, and efficiency) for future use? Stages in master planning, programming, and architectural design.

PubMed

Westlake, P

1995-10-01

Health care facility design must incorporate four key elements: Strategy, Assessment, Flexibility, and Efficiency. These SAFE elements will offer the organization the greatest return on investment, because they encompass both present needs and future demand. They respect the integrated nature of functional operations by clustering them in ways that permit growth or consolidation. In the rapidly changing health care environment, flexibility is fundamental to successful design.

Crossing the Chasm--Introducing Flexible Learning into the Botswana Technical Education Programme: From Policy to Action

ERIC Educational Resources Information Center

Richardson, Alison Mead

2009-01-01

This paper reports on a longitudinal, ethnomethodological case study of the development towards flexible delivery of the Botswana Technical Education Programme (BTEP), offered by Francistown College of Technical & Vocational Education (FCTVE). Data collection methods included documentary analysis, naturalistic participant observation, and…

Flexible Reporting Options for Skilled Child Abuse Professionals.

ERIC Educational Resources Information Center

Finkelhor, David; Zellman, Gail L.

1991-01-01

Proposed is a system of flexible options for the mandated reporting of child abuse and neglect, to improve compliance with and reduce burdens on the child protective system. Potential benefits and drawbacks of the plan, which would identify and train "registered reporters" and offer the option of explicit deferred investigation, are…

Wisconsin ESEA Flexibility Request. Amended 2013

ERIC Educational Resources Information Center

US Department of Education, 2013

2013-01-01

The U.S. Department of Education (Department) is offering each State educational agency (SEA) the opportunity to request flexibility on behalf of itself, its local educational agencies (LEAs), and its schools, in order to better focus on improving student learning and increasing the quality of instruction. This voluntary opportunity will provide…

Review of recent progresses on flexible oxide semiconductor thin film transistors based on atomic layer deposition processes

NASA Astrophysics Data System (ADS)

Sheng, Jiazhen; Han, Ki-Lim; Hong, TaeHyun; Choi, Wan-Ho; Park, Jin-Seong

2018-01-01

The current article is a review of recent progress and major trends in the field of flexible oxide thin film transistors (TFTs), fabricating with atomic layer deposition (ALD) processes. The ALD process offers accurate controlling of film thickness and composition as well as ability of achieving excellent uniformity over large areas at relatively low temperatures. First, an introduction is provided on what is the definition of ALD, the difference among other vacuum deposition techniques, and the brief key factors of ALD on flexible devices. Second, considering functional layers in flexible oxide TFT, the ALD process on polymer substrates may improve device performances such as mobility and stability, adopting as buffer layers over the polymer substrate, gate insulators, and active layers. Third, this review consists of the evaluation methods of flexible oxide TFTs under various mechanical stress conditions. The bending radius and repetition cycles are mostly considering for conventional flexible devices. It summarizes how the device has been degraded/changed under various stress types (directions). The last part of this review suggests a potential of each ALD film, including the releasing stress, the optimization of TFT structure, and the enhancement of device performance. Thus, the functional ALD layers in flexible oxide TFTs offer great possibilities regarding anti-mechanical stress films, along with flexible display and information storage application fields. Project supported by the National Research Foundation of Korea (NRF) (No. NRF-2017R1D1A1B03034035), the Ministry of Trade, Industry & Energy (No. #10051403), and the Korea Semiconductor Research Consortium.

Developing Architectures and Technologies for an Evolvable NASA Space Communication Infrastructure

NASA Technical Reports Server (NTRS)

Bhasin, Kul; Hayden, Jeffrey

2004-01-01

Space communications architecture concepts play a key role in the development and deployment of NASA's future exploration and science missions. Once a mission is deployed, the communication link to the user needs to provide maximum information delivery and flexibility to handle the expected large and complex data sets and to enable direct interaction with the spacecraft and experiments. In human and robotic missions, communication systems need to offer maximum reliability with robust two-way links for software uploads and virtual interactions. Identifying the capabilities to cost effectively meet the demanding space communication needs of 21st century missions, proper formulation of the requirements for these missions, and identifying the early technology developments that will be needed can only be resolved with architecture design. This paper will describe the development of evolvable space communication architecture models and the technologies needed to support Earth sensor web and collaborative observation formation missions; robotic scientific missions for detailed investigation of planets, moons, and small bodies in the solar system; human missions for exploration of the Moon, Mars, Ganymede, Callisto, and asteroids; human settlements in space, on the Moon, and on Mars; and great in-space observatories for observing other star systems and the universe. The resulting architectures will enable the reliable, multipoint, high data rate capabilities needed on demand to provide continuous, maximum coverage of areas of concentrated activities, such as in the vicinity of outposts in-space, on the Moon or on Mars.

49 CFR 178.812 - Top lift test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... renders the IBC, including the base pallets when applicable, unsafe for transportation, and no loss of... twice the maximum permissible gross mass with the load being evenly distributed. (2) Flexible IBC design types must be filled to six times the maximum net mass, the load being evenly distributed. (c) Test...

49 CFR 178.812 - Top lift test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... renders the IBC, including the base pallets when applicable, unsafe for transportation, and no loss of... twice the maximum permissible gross mass with the load being evenly distributed. (2) Flexible IBC design types must be filled to six times the maximum net mass, the load being evenly distributed. (c) Test...

49 CFR 178.812 - Top lift test.

Code of Federal Regulations, 2012 CFR

2012-10-01

... renders the IBC, including the base pallets when applicable, unsafe for transportation, and no loss of... twice the maximum permissible gross mass with the load being evenly distributed. (2) Flexible IBC design types must be filled to six times the maximum net mass, the load being evenly distributed. (c) Test...

49 CFR 178.812 - Top lift test.

Code of Federal Regulations, 2011 CFR

2011-10-01

... renders the IBC, including the base pallets when applicable, unsafe for transportation, and no loss of... twice the maximum permissible gross mass with the load being evenly distributed. (2) Flexible IBC design types must be filled to six times the maximum net mass, the load being evenly distributed. (c) Test...

Tunable TiO2 Nanotube Arrays for Flexible Bio-Sensitized Solar Cells

DTIC Science & Technology

2012-08-01

microid extender followed by a colloidal silica /wetted imperial cloth. The foil was then cut into 1- × 2-cm samples. Then, the substrates were...17. Lei, B.; Liao, J.; Wang, R. J.; Su, C.; Kuang, D. Ordered Crystalline Ti02 Nanotube Arrays on Transparent FTO Glass for Efficient Dye...combined with a transparent , Indium Tin Dioxide coated PET film are attractive candidates for efficient, flexible DSSC’s. Flexible solar cells offer

IR Sensor Synchronizing Active Shutter Glasses for 3D HDTV with Flexible Liquid Crystal Lenses

PubMed Central

Han, Jeong In

2013-01-01

IR sensor synchronizing active shutter glasses for three-dimensional high definition television (3D HDTV) were developed using a flexible liquid crystal (FLC) lens. The FLC lens was made on a polycarbonate (PC) substrate using conventional liquid crystal display (LCD) processes. The flexible liquid crystal lens displayed a maximum transmission of 32% and total response time of 2.56 ms. The transmittance, the contrast ratio and the response time of the flexible liquid crystal lens were superior to those of glass liquid crystal lenses. Microcontroller unit and drivers were developed as part of a reception module with power supply for the IR sensor synchronizing active shutter glasses with the flexible liquid crystal lens prototypes. IR sensor synchronizing active shutter glasses for 3D HDTV with flexible liquid crystal lenses produced excellent 3D images viewing characteristics.

Choosing health: qualitative evidence from the experiences of personal health budget holders.

PubMed

Davidson, Jacqueline; Baxter, Kate; Glendinning, Caroline; Irvine, Annie

2013-10-01

Personal health budgets were piloted in the English National Health Service between 2009 and 2012. Semi-structured interviews with a sub-sample of early budget holders aimed to explore their experiences of receiving and using a budget. Over 2000 people from 20 pilot sites were recruited to a multi-method evaluation of the personal health budget pilots. A sub-sample of 58 people was selected for qualitative interviews three months after the offer of a budget; 52 were re-interviewed six months later. The purposively selected sample reflected a range of health conditions, locality, age and gender. Personal health budgets were reported to have positive impacts on health, health care and relatives/family. Benefits often extended beyond the condition for which the budget had been awarded. However, interviewees rarely knew the level of their budget; some reported difficulty in agreeing acceptable uses for their budget; and delays could occur in procuring chosen services or equipment. Patients' experiences offer valuable insights for the roll-out of personal health budgets beyond the pilot phase. Flexibility in how budgets are used may allow maximum benefits to be derived. Clear information about what budgets can and cannot be used for, with suggestions offered, will be useful. People with newly diagnosed or recent sudden onset conditions may need more help to plan their support, but all budget holders are likely to benefit from regular contact with staff for reassurance and continued motivation.

Flexible Grouping for Literacy in the Elementary Grades.

ERIC Educational Resources Information Center

Radencich, Marguerite C.; McKay, Lyn J.

Presenting an in-depth look at alternatives to ability grouping in elementary school reading and language arts programs, this book presents eight essays that offer a variety of practical suggestions and resources for educators interested in moving to or enhancing their use of flexible grouping for reading instruction. The book describes programs…

Flexible Studies as Strategy for Lifelong Learning

ERIC Educational Resources Information Center

Bugge, Liv Susanne; Wikan, Gerd

2016-01-01

Many countries face a challenge in recruiting teachers. At the same time, the labour market is changing and the demand for re-education is increasing. In this situation, lifelong learning is seen as relevant and higher education institutions are asked to offer flexible and decentralised study programmes in order to accommodate the need for formal…

Designing E-Learning Environments for Flexible Activity and Instruction

ERIC Educational Resources Information Center

Wilson, Brent G.

2004-01-01

The contributions to this issue share a focus on design of e-learning environments. Instructional designers stand at very early stages of knowledge in this area, but with great potential for growth and progress. This commentary offers an activity-based perspective on e-learning environments, resulting in a flexible stance toward instructional…

Lecture Recording: Structural and Symbolic Information vs. Flexibility of Presentation

ERIC Educational Resources Information Center

Stolzenberg, Daniel; Pforte, Stefan

2007-01-01

Rapid eLearning is an ongoing trend which enables flexible and cost-effective creation of learning materials. Especially, lecture recording has turned out to be a lightweight method particularly suited for existing lectures and blended learning strategies. In order to not only sequentially play back but offer full fledged navigation, search and…

Cost-Effective, Equitable and Flexible Higher Education through Open and Distance Learning in Bangladesh

ERIC Educational Resources Information Center

Islam, Tofazzal

2011-01-01

This paper examines how this mega-university offers increasing access to cost-effective, equitable and flexible higher education by analyzing data from primary and secondary sources, identifies challenges impacting the continued growth of enrollment in distance education, and outlines opportunities for increasing access to higher education through…

Linguistic Flexibility Modulates Speech Planning for Causative Motion Events: A Cross-Linguistic Study of Mandarin and English

ERIC Educational Resources Information Center

Zheng, Chun

2017-01-01

Producing a sensible utterance requires speakers to select conceptual content, lexical items, and syntactic structures almost instantaneously during speech planning. Each language offers its speakers flexibility in the selection of lexical and syntactic options to talk about the same scenarios involving movement. Languages also vary typologically…

Bento and Buffet: Two Approaches to Flexible Summative Assessment

ERIC Educational Resources Information Center

Didicher, Nicky

2016-01-01

This practice-sharing piece outlines two main approaches to flexible summative assessment schemes, including for each approach one example from my practice and another from a published study. The bento approach offers the same assessments to all students but a variety of grade weighting schemes, allowing students to change weighting during the…

Management Education Benchmarking Designing Customized and Flexible MBA Programs

ERIC Educational Resources Information Center

Hall, Owen P., Jr.; Young, Terry W.

2007-01-01

To meet the challenges of the 21st century B-schools are revising curriculum, delivery and outcome assessment modalities. Today, the proportion of electives and other specialty offerings in many MBA programs now constitutes more than 50% of the total curriculum. However, this focus on customization, integration and flexibility is not without its…

Changing States of Matter: Science, Education, and Giftedness in 21st Century High Schools.

ERIC Educational Resources Information Center

Sytsma, Rachel E.

2001-01-01

This article uses the change of solids to liquids to gases as a metaphor for the need of high school gifted education to change from current rigid forms to the liquidity of increased flexibility, individual opportunity, and freedom and the maximum energy, freedom and flexibility (gaseous state) achieved by gifted education at its best. (Contains…

Ferroelectric hybrid fibers to develop flexible sensors for shape sensing of smart textiles and soft condensed matter bodies

NASA Astrophysics Data System (ADS)

Sebastian, Tutu; Lusiola, Tony; Clemens, Frank

2017-04-01

Piezoelectric fibers are widely used in composites for actuator and sensor applications due to its ability to convert electrical pulses into mechanical vibrations and transform the returned mechanical vibrations back into electrical signal. They are beneficial for the fabrication of composites especially 1-3 composites, active fiber composites (unidirectional axially aligned PZT fibers sandwiched between interdigitated electrodes and embedded in a polymer matrix) etc, with potential applications in medical imaging, structural health monitoring, energy harvesting, vibration and noise control. However, due to the brittle nature of PZT fibers, maximum strain is limited to 0.2% and cannot be integrated into flexible sensor applications. In this contribution, a new approach to develop flexible ferroelectric hybrid fibers for soft body shape sensing is investigated. Piezoelectric particles incorporated in a polymer matrix and extruded as fiber, 0-3 composite in fibrous form is studied. Commercially obtained calcined PZT and calcined BaTiO3 powders were used in the unsintered form to obtain flexible soft condensed matter ferroelectric hybrid fibers. The extruded fibers were subjected to investigation for their electromechanical behavior as a function of electric field. The hybrid fibers reached 10% of the maximum polarization of their sintered counterpart.

Comparison of standard maximum likelihood classification and polytomous logistic regression used in remote sensing

Treesearch

John Hogland; Nedret Billor; Nathaniel Anderson

2013-01-01

Discriminant analysis, referred to as maximum likelihood classification within popular remote sensing software packages, is a common supervised technique used by analysts. Polytomous logistic regression (PLR), also referred to as multinomial logistic regression, is an alternative classification approach that is less restrictive, more flexible, and easy to interpret. To...

High-throughput optical inter-board interconnects for next-generation on-board digital transparent processors

NASA Astrophysics Data System (ADS)

Venet, N.; Sotom, M.; Gachon, H.; Foucal, V.; Pez, M.; Heikkinen, V.; Tuominen, T.; Pantoja, S.

2017-11-01

The satellite telecommunication sector is continuously facing new challenges. Operators turn towards increasing capacity payloads with higher number of beams and broader bandwidth, in order to cope with exhausting orbital positions and to lower the cost of in-orbit delivery of bit. Only satellites able to provide high data rate connections to numerous users are expected to achieve affordable communication prices. On the other hand, as the telecom market grows and the range of offered services (HDTV, Video On Demand, Triple Play), operators call for more versatile solutions to quickly grasp new markets and to adapt to these evolutions over the average 15 years of a satellite lifetime. Flexible payloads have found an increasing interest for a number of years. Flexibility is considered as a means for a better commercial exploitation of a satellite fleet and a better allocation of resource in response to traffic evolution and/or changing business plans, with potential advantages such as a wider range of applications, less customization for specific missions, increased production runs of equipment, enhancement of reliability, reduction of equipment cost, reduction of program schedules [1]. Flexibility is expected to be offered in spectrum management and frequency plan, in coverage, or in the repeater power allocation. The industry is taking up the challenge both by improving current telecom satellites and offering new payload technology, more flexible and able to address the new markets. From a system integrator perspective, flexibility is as an opportunity to design more generic payloads, that can be customized during or after fabrication only, thus shortening the design-to-manufacturing cycle, and improving the industry competitiveness.

Turbulent drag reduction by flexible and rodlike polymers: Crossover effects at small concentrations.

PubMed

Ching, Emily S C; Lo, T S; Procaccia, Itamar

2006-08-01

Drag reduction by polymers is bounded between two universal asymptotes, the von Kármán log law of the law and the maximum drag reduction (MDR) asymptote. It is theoretically understood why the MDR asymptote is universal, independent of whether the polymers are flexible or rodlike. The crossover behavior from the Newtonian von Kármán log law to the MDR is, however, not universal, showing different characteristics for flexible and rodlike polymers. In this paper we provide a theory for this crossover phenomenology.

Managing a work-life balance: the experiences of midwives working in a group practice setting.

PubMed

Fereday, Jennifer; Oster, Candice

2010-06-01

To explore how a group of midwives achieved a work-life balance working within a caseload model of care with flexible work hours and on-call work. in-depth interviews were conducted and the data were analysed using a data-driven thematic analysis technique. Children, Youth and Women's Health Service (CYWHS) (previously Women's and Children's Hospital), Adelaide, where a midwifery service known as Midwifery Group Practice (MGP) offers a caseload model of care to women within a midwife-managed unit. 17 midwives who were currently working, or had previously worked, in MGP. analysis of the midwives' individual experiences provided insight into how midwives managed the flexible hours and on-call work to achieve a sustainable work-life balance within a caseload model of care. it is important for midwives working in MGP to actively manage the flexibility of their role with time on call. Organisational, team and individual structure influenced how flexibility of hours was managed; however, a period of adjustment was required to achieve this balance. the study findings offer a description of effective, sustainable strategies to manage flexible hours and on-call work that may assist other midwives working in a similar role or considering this type of work setting. Copyright 2008 Elsevier Ltd. All rights reserved.

Impedance-matching system for a flexible surface-coil-type resonator

NASA Astrophysics Data System (ADS)

Hirata, Hiroshi; Ono, Mitsuhiro

1997-09-01

This article describes an impedance-matching system for a flexible surface-coil-type resonator (FSCR) used in electron paramagnetic resonance (EPR) experiments. To design the matching system, the input impedance of the FSCR was formulated using transmission line theory, and then the parameters of a matching circuit using varicap diodes were calculated. Experimental measurements of input impedance showed the validity of the formulation and the usefulness of the matching system. The matching circuit made by the varicap diodes 1SV186 offered the tunable bandwidth of 50 MHz for the prototype FSCR. Such a matching system also offers the possibility of remotely tuning EPR resonators electronically.

Families with school-age children.

PubMed

Christensen, Kathleen; Schneider, Barbara; Butler, Donnell

2011-01-01

Most working parents face a common dilemma--how to care for their children when they are not in school but the parents are at work. In this article Kathleen Christensen, Barbara Schneider, and Donnell Butler describe the predictable and unpredictable scheduling demands school-age children place on working couples and single working parents. The authors assess the potential capacity of schools to help meet the needs of working families through changes in school schedules and after-school programs and conclude that the flexibility parents need to balance family-work responsibilities probably cannot be found in the school setting. They argue that workplaces are better able than schools to offer the flexibility that working parents need to attend to basic needs of their children, as well as to engage in activities that enhance their children's academic performance and emotional and social well-being. Two types of flexible work practices seem especially well suited to parents who work: flextime arrangements that allow parents to coordinate their work schedules with their children's school schedules, and policies that allow workers to take short periods of time off--a few hours or a day or two-to attend a parent-teacher conference, for example, or care for a child who has suddenly fallen ill. Many companies that have instituted such policies have benefited through employees' greater job satisfaction and employee retention. Yet despite these measured benefits to employers, workplaces often fall short of being family friendly. Many employers do not offer such policies or offer them only to employees at certain levels or in certain types of jobs. Flexible work practices are almost nonexistent for low-income workers, who are least able to afford alternative child care and may need flexibility the most. Moreover the authors find that even employees in firms with flexible practices such as telecommuting may be reluctant to take advantage of them, because the workplace culture explicitly or implicitly stigmatizes or penalizes employees for choosing these work arrangements. The authors conclude by making a case for creating a workplace culture that supports flexibility. Such a culture, they argue, would enable working parents to better meet the responsibilities of their jobs as they care for and build strong relationships with their children.

Comparison study on flexible pavement design using FAA (Federal Aviation Administration) and LCN (Load Classification Number) code in Ahmad Yani international airport’s runway

NASA Astrophysics Data System (ADS)

Santoso, S. E.; Sulistiono, D.; Mawardi, A. F.

2017-11-01

FAA code for airport design has been broadly used by Indonesian Ministry of Aviation since decades ago. However, there is not much comprehensive study about its relevance and efficiency towards current situation in Indonesia. Therefore, a further comparison study on flexible pavement design for airport runway using comparable method has become essential. The main focus of this study is to compare which method between FAA and LCN that offer the most efficient and effective way in runway pavement planning. The comparative methods in this study mainly use the variety of variable approach. FAA code for instance, will use the approach on the aircraft’s maximum take-off weight and annual departure. Whilst LCN code use the variable of equivalent single wheel load and tire pressure. Based on the variables mentioned above, a further classification and rated method will be used to determine which code is best implemented. According to the analysis, it is clear that FAA method is the most effective way to plan runway design in Indonesia with consecutively total pavement thickness of 127cm and LCN method total pavement thickness of 70cm. Although, FAA total pavement is thicker that LCN its relevance towards sustainable and pristine condition in the future has become an essential aspect to consider in design and planning.

Acute Lower Extremity Running Kinematics After a Hamstring Stretch

PubMed Central

Davis Hammonds, Autumn L.; Laudner, Kevin G.; McCaw, Steve; McLoda, Todd A.

2012-01-01

Context: Limited passive hamstring flexibility might affect kinematics, performance, and injury risk during running. Pre-activity static straight-leg raise stretching often is used to gain passive hamstring flexibility. Objective: To investigate the acute effects of a single session of passive hamstring stretching on pelvic, hip, and knee kinematics during the swing phase of running. Design: Randomized controlled clinical trial. Setting: Biomechanics research laboratory. Patients or Other Participants: Thirty-four male (age = 21.2 ± 1.4 years) and female (age = 21.3±2.0 years) recreational athletes. Intervention(s): Participants performed treadmill running pretests and posttests at 70% of their age-predicted maximum heart rate. Pelvis, hip, and knee joint angles during the swing phase of 5 consecutive gait cycles were collected using a motion analysis system. Right and left hamstrings of the intervention group participants were passively stretched 3 times for 30 seconds in random order immediately after the pretest. Control group participants performed no stretching or movement between running sessions. Main Outcome Measure(s): Six 2-way analyses of variance to determine joint angle differences between groups at maximum hip flexion and maximum knee extension with an α level of .008. Results: Flexibility increased between pretest and post-test in all participants (F1,30 = 80.61, P<.001). Anterior pelvic tilt (F1,30 = 0.73, P=.40), hip flexion (F1,30 = 2.44, P=.13), and knee extension (F1,30 = 0.06, P=.80) at maximum hip flexion were similar between groups throughout testing. Anterior pelvic tilt (F1,30 = 0.69, P=.41), hip flexion (F1,30 = 0.23, P=.64), and knee extension (F1,30 = 3.38, P=.62) at maximum knee extension were similar between groups throughout testing. Men demonstrated greater anterior pelvic tilt than women at maximum knee extension (F1,30 = 13.62, P=.001). Conclusions: A single session of 3 straight-leg raise hamstring stretches did not change pelvis, hip, or knee running kinematics. PMID:22488225

Organizations' Ways of Employing Early Retirees: The Role of Age-Based HR Policies.

PubMed

Oude Mulders, Jaap; Henkens, Kène; Schippers, Joop

2015-06-01

We examine whether from an organizational perspective it is possible to distinguish different ways of employing early retirees and explore how the employment of early retirees is related to the application of 4 age-based human resource (HR) policies, namely demotion, offering training opportunities to older workers, offering early retirement, and allowing flexible working hours. We perform a latent class analysis on a sample of 998 Dutch organizations in order to categorize them based on 3 dimensions of their employment of early retirees. We then run a multinomial logistic regression to relate the employment of early retirees to the 4 age-based HR policies. We distinguish 4 types of organizations based on their way of employing early retirees: nonusers (52.6%), users for mainly standard work (20.8%), users for mainly nonstandard work (9.8%), and users for standard and nonstandard work (16.7%). We find that organizations that apply demotion, offer early retirement, and allow flexible working hours are more likely to be users for mainly standard work. Also, organizations that do not offer early retirement are less likely to employ early retirees. Age-based HR policies, especially demotion, offering early retirement, and allowing flexible working hours, are conducive to the employment of early retirees for mainly standard work. Broader implementation of these policies may provide opportunities for older workers to make a more gradual transition from work to retirement. © The Author 2013. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Static aeroelastic deformation of flexible skin for continuous variable trailing-edge camber wing

NASA Astrophysics Data System (ADS)

Liu, Libo; Yin, Weilong; Dai, Fuhong; Liu, Yanju; Leng, Jinsong

2011-03-01

The method for analyzing the static aeroelastic deformation of flexible skin under the air loads was developed. The effect of static aeroelastic deformation of flexible skin on the aerodynamic characteristics of aerofoil and the design parameters of skin was discussed. Numerical results show that the flexible skin on the upper surface of trailing-edge will bubble under the air loads and the bubble has a powerful effect on the aerodynamic pressure near the surface of local deformation. The static aeroelastic deformation of flexible skin significantly affects the aerodynamic characteristics of aerofoil. At small angle of attack, the drag coefficient increases and the lift coefficient decreases. With the increasing angle of attack, the effect of flexible skin on the aerodynamic characteristics of aerofoil is smaller and smaller. The deformation of flexible skin becomes larger and larger with the free-stream velocity increasing. When the free-stream velocity is greater than a value, both of the deformation of flexible skin and the drag coefficient of aerofoil increase rapidly. The maximum tensile strain of flexible skin is increased with consideration of the static aeroelastic deformation.

Estimating Scale Economies and the Optimal Size of School Districts: A Flexible Form Approach

ERIC Educational Resources Information Center

Schiltz, Fritz; De Witte, Kristof

2017-01-01

This paper investigates estimation methods to model the relationship between school district size, costs per student and the organisation of school districts. We show that the assumptions on the functional form strongly affect the estimated scale economies and offer two possible solutions to allow for more flexibility in the estimation method.…

A Model for Flexibly Editing CSCL Scripts

ERIC Educational Resources Information Center

Sobreira, Pericles; Tchounikine, Pierre

2012-01-01

This article presents a model whose primary concern and design rationale is to offer users (teachers) with basic ICT skills an intuitive, easy, and flexible way of editing scripts. The proposal is based on relating an end-user representation as a table and a machine model as a tree. The table-tree model introduces structural expressiveness and…

Graduate Program Scheduling Gains Flexibility through Container Courses: A Case Study

ERIC Educational Resources Information Center

Rose, Richard

2011-01-01

Online course delivery makes possible one innovation which can provide each student with greater program flexibility as well as some personal ownership of the direction and pace of his degree progress. This concept can be called the "container course." A container course is the offering of more than one course simultaneously under a single course…

The Motherhood Wage Penalty Revisited: Experience, Heterogeneity, Work Effort, and Work-Schedule Flexibility.

ERIC Educational Resources Information Center

Anderson, Deborah J.; Binder, Melissa; Krause, Kate

2003-01-01

Controlling for human capital inputs and unobserved heterogeneity explained 55-57% of the wage gap between mothers and nonmothers. Mothers faced the highest wage penalty at return to work. High school graduates suffered more prolonged, severe losses than women with lower or higher attainment. Their jobs were less likely to offer flexibility needed…

Teaching the Practice of Compassion to Nursing Students within an Online Learning Environment: A Qualitative Study Protocol

ERIC Educational Resources Information Center

Hofmeyer, Anne; Toffoli, Luisa; Vernon, Rachael; Taylor, Ruth; Fontaine, Dorrie; Klopper, Hester C.; Coetzee, Siedine Knobloch

2016-01-01

Background: There is an increasing global demand for higher education to incorporate flexible delivery. Nursing education has been at the forefront of developing flexible online education and offering programs "anywhere and anytime". In response to calls to teach compassion in nursing education, there is an abundance of literature…

Applications technology satellite F&G /ATS F&G/ mobile terminal.

NASA Technical Reports Server (NTRS)

Greenbaum, L. A.; Baker, J. L.

1971-01-01

The mobile terminal is a flexible, easily transportable system. The terminal design incorporates a combination of unique and proven hardware to provide maximum utility consistent with reliability. The flexibility built into the system will make it possible to satisfy the requirements of the applications technology satellite program concerned with the conduction of various spacecraft technology experiments. The terminal includes two parabolic antennas.

49 CFR 178.812 - Top lift test.

Code of Federal Regulations, 2010 CFR

2010-10-01

... no loss of contents. [Amdt. 178-103, 59 FR 38074, July 26, 1994, as amended at 66 FR 33452, June 21... types must be loaded to twice the maximum permissible gross mass with the load being evenly distributed. (2) Flexible IBC design types must be filled to six times the maximum net mass, the load being evenly...

Modeling Academic Education Processes by Dynamic Storyboarding

ERIC Educational Resources Information Center

Sakurai, Yoshitaka; Dohi, Shinichi; Tsuruta, Setsuo; Knauf, Rainer

2009-01-01

In high-level education such as university studies, there is a flexible but complicated system of subject offerings and registration rules such as prerequisite subjects. Those offerings, connected with registration rules, should be matched to the students' learning needs and desires, which change dynamically. Students need assistance in such a…

Introduction to the Unified Agenda of Federal Regulatory and Deregulatory Actions

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-26

... Regulatory Agencies Federal Communications Commission 21903 Federal Reserve System 21949 Federal Trade... Register twice each year since 1983 and has been available online since 1995. To further the objective of...://reginfo.gov . The online Unified Agenda offers flexible search tools and will soon offer access to the...

Tax-exempt private placements: a new opportunity for not-for-profit providers.

PubMed

Ambrose, Jim; Harris, Andrew

2006-08-01

Tax-exempt private placements offer an attractive financing alternative for not-for-profit healthcare providers for which the public debt market is no longer a viable option. They offer the following advantages: Greater flexibility Lower fees. Less paperwork. Fewer players. Shorter time to complete.

Effect of static shape deformation on aerodynamics and aerothermodynamics of hypersonic inflatable aerodynamic decelerator

NASA Astrophysics Data System (ADS)

Guo, Jinghui; Lin, Guiping; Bu, Xueqin; Fu, Shiming; Chao, Yanmeng

2017-07-01

The inflatable aerodynamic decelerator (IAD), which allows heavier and larger payloads and offers flexibility in landing site selection at higher altitudes, possesses potential superiority in next generation space transport system. However, due to the flexibilities of material and structure assembly, IAD inevitably experiences surface deformation during atmospheric entry, which in turn alters the flowfield around the vehicle and leads to the variations of aerodynamics and aerothermodynamics. In the current study, the effect of the static shape deformation on the hypersonic aerodynamics and aerothermodynamics of a stacked tori Hypersonic Inflatable Aerodynamic Decelerator (HIAD) is demonstrated and analyzed in detail by solving compressible Navier-Stokes equations with Menter's shear stress transport (SST) turbulence model. The deformed shape is obtained by structural modeling in the presence of maximum aerodynamic pressure during entry. The numerical results show that the undulating shape deformation makes significant difference to flow structure. In particular, the more curved outboard forebody surface results in local flow separations and reattachments in valleys, which consequently yields remarkable fluctuations of surface conditions with pressure rising in valleys yet dropping on crests while shear stress and heat flux falling in valleys yet rising on crests. Accordingly, compared with the initial (undeformed) shape, the corresponding differences of surface conditions get more striking outboard, with maximum augmentations of 379 pa, 2224 pa, and 19.0 W/cm2, i.e., 9.8%, 305.9%, and 101.6% for the pressure, shear stress and heat flux respectively. Moreover, it is found that, with the increase of angle of attack, the aerodynamic characters and surface heating vary and the aeroheating disparities are evident between the deformed and initial shape. For the deformable HIAD model investigated in this study, the more intense surface conditions and changed flight aerodynamics are revealed, which is critical for the selection of structure material and design of flight control system.

Compact Spreader Schemes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Placidi, M.; Jung, J. -Y.; Ratti, A.

2014-07-25

This paper describes beam distribution schemes adopting a novel implementation based on low amplitude vertical deflections combined with horizontal ones generated by Lambertson-type septum magnets. This scheme offers substantial compactness in the longitudinal layouts of the beam lines and increased flexibility for beam delivery of multiple beam lines on a shot-to-shot basis. Fast kickers (FK) or transverse electric field RF Deflectors (RFD) provide the low amplitude deflections. Initially proposed at the Stanford Linear Accelerator Center (SLAC) as tools for beam diagnostics and more recently adopted for multiline beam pattern schemes, RFDs offer repetition capabilities and a likely better amplitude reproducibilitymore » when compared to FKs, which, in turn, offer more modest financial involvements both in construction and operation. Both solutions represent an ideal approach for the design of compact beam distribution systems resulting in space and cost savings while preserving flexibility and beam quality.« less

A Joint Model for Longitudinal Measurements and Survival Data in the Presence of Multiple Failure Types

PubMed Central

Elashoff, Robert M.; Li, Gang; Li, Ning

2009-01-01

Summary In this article we study a joint model for longitudinal measurements and competing risks survival data. Our joint model provides a flexible approach to handle possible nonignorable missing data in the longitudinal measurements due to dropout. It is also an extension of previous joint models with a single failure type, offering a possible way to model informatively censored events as a competing risk. Our model consists of a linear mixed effects submodel for the longitudinal outcome and a proportional cause-specific hazards frailty submodel (Prentice et al., 1978, Biometrics 34, 541-554) for the competing risks survival data, linked together by some latent random effects. We propose to obtain the maximum likelihood estimates of the parameters by an expectation maximization (EM) algorithm and estimate their standard errors using a profile likelihood method. The developed method works well in our simulation studies and is applied to a clinical trial for the scleroderma lung disease. PMID:18162112

Additive hazards regression and partial likelihood estimation for ecological monitoring data across space.

PubMed

Lin, Feng-Chang; Zhu, Jun

2012-01-01

We develop continuous-time models for the analysis of environmental or ecological monitoring data such that subjects are observed at multiple monitoring time points across space. Of particular interest are additive hazards regression models where the baseline hazard function can take on flexible forms. We consider time-varying covariates and take into account spatial dependence via autoregression in space and time. We develop statistical inference for the regression coefficients via partial likelihood. Asymptotic properties, including consistency and asymptotic normality, are established for parameter estimates under suitable regularity conditions. Feasible algorithms utilizing existing statistical software packages are developed for computation. We also consider a simpler additive hazards model with homogeneous baseline hazard and develop hypothesis testing for homogeneity. A simulation study demonstrates that the statistical inference using partial likelihood has sound finite-sample properties and offers a viable alternative to maximum likelihood estimation. For illustration, we analyze data from an ecological study that monitors bark beetle colonization of red pines in a plantation of Wisconsin.

How to resolve microsecond current fluctuations in single ion channels: The power of beta distributions

PubMed Central

Schroeder, Indra

2015-01-01

Abstract A main ingredient for the understanding of structure/function correlates of ion channels is the quantitative description of single-channel gating and conductance. However, a wealth of information provided from fast current fluctuations beyond the temporal resolution of the recording system is often ignored, even though it is close to the time window accessible to molecular dynamics simulations. This kind of current fluctuations provide a special technical challenge, because individual opening/closing or blocking/unblocking events cannot be resolved, and the resulting averaging over undetected events decreases the single-channel current. Here, I briefly summarize the history of fast-current fluctuation analysis and focus on the so-called “beta distributions.” This tool exploits characteristics of current fluctuation-induced excess noise on the current amplitude histograms to reconstruct the true single-channel current and kinetic parameters. A guideline for the analysis and recent applications demonstrate that a construction of theoretical beta distributions by Markov Model simulations offers maximum flexibility as compared to analytical solutions. PMID:26368656

Flexible black phosphorus ambipolar transistors, circuits and AM demodulator.

PubMed

Zhu, Weinan; Yogeesh, Maruthi N; Yang, Shixuan; Aldave, Sandra H; Kim, Joon-Seok; Sonde, Sushant; Tao, Li; Lu, Nanshu; Akinwande, Deji

2015-03-11

High-mobility two-dimensional (2D) semiconductors are desirable for high-performance mechanically flexible nanoelectronics. In this work, we report the first flexible black phosphorus (BP) field-effect transistors (FETs) with electron and hole mobilities superior to what has been previously achieved with other more studied flexible layered semiconducting transistors such as MoS2 and WSe2. Encapsulated bottom-gated BP ambipolar FETs on flexible polyimide afforded maximum carrier mobility of about 310 cm(2)/V·s with field-effect current modulation exceeding 3 orders of magnitude. The device ambipolar functionality and high-mobility were employed to realize essential circuits of electronic systems for flexible technology including ambipolar digital inverter, frequency doubler, and analog amplifiers featuring voltage gain higher than other reported layered semiconductor flexible amplifiers. In addition, we demonstrate the first flexible BP amplitude-modulated (AM) demodulator, an active stage useful for radio receivers, based on a single ambipolar BP transistor, which results in audible signals when connected to a loudspeaker or earphone. Moreover, the BP transistors feature mechanical robustness up to 2% uniaxial tensile strain and up to 5000 bending cycles.

Ultrathin cerium orthovanadate nanobelts for high-performance flexible all-solid-state asymmetric supercapacitors.

PubMed

He, Junzhi; Zhao, Junhong; Run, Zhen; Sun, Mengjun; Pang, Huan

2015-02-01

Ultrathin CeVO4 nanobelts were successfully synthesized by a hydrothermal method. The thickness of a single nanobelt is about 2.4 nm, which can effectively shorten the ion diffusion and fasten the charge pathway. More importantly, ultrathin CeVO4 nanobelts and graphene are easily assembled as a flexible all-solid-state asymmetric device, which shows a highly flexible property and achieves a maximum energy density of 0.78 mW h cm(-3) and a high life cycle of >6000 cycles. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Continuous, highly flexible, and transparent graphene films by chemical vapor deposition for organic photovoltaics.

PubMed

Gomez De Arco, Lewis; Zhang, Yi; Schlenker, Cody W; Ryu, Koungmin; Thompson, Mark E; Zhou, Chongwu

2010-05-25

We report the implementation of continuous, highly flexible, and transparent graphene films obtained by chemical vapor deposition (CVD) as transparent conductive electrodes (TCE) in organic photovoltaic cells. Graphene films were synthesized by CVD, transferred to transparent substrates, and evaluated in organic solar cell heterojunctions (TCE/poly-3,4-ethylenedioxythiophene:poly styrenesulfonate (PEDOT:PSS)/copper phthalocyanine/fullerene/bathocuproine/aluminum). Key to our success is the continuous nature of the CVD graphene films, which led to minimal surface roughness ( approximately 0.9 nm) and offered sheet resistance down to 230 Omega/sq (at 72% transparency), much lower than stacked graphene flakes at similar transparency. In addition, solar cells with CVD graphene and indium tin oxide (ITO) electrodes were fabricated side-by-side on flexible polyethylene terephthalate (PET) substrates and were confirmed to offer comparable performance, with power conversion efficiencies (eta) of 1.18 and 1.27%, respectively. Furthermore, CVD graphene solar cells demonstrated outstanding capability to operate under bending conditions up to 138 degrees , whereas the ITO-based devices displayed cracks and irreversible failure under bending of 60 degrees . Our work indicates the great potential of CVD graphene films for flexible photovoltaic applications.

Microfluidics on compliant substrates: recent developments in foldable and bendable devices and system packaging

NASA Astrophysics Data System (ADS)

Gray, Bonnie L.

2012-04-01

Microfluidics is revolutionizing laboratory methods and biomedical devices, offering new capabilities and instrumentation in multiple areas such as DNA analysis, proteomics, enzymatic analysis, single cell analysis, immunology, point-of-care medicine, personalized medicine, drug delivery, and environmental toxin and pathogen detection. For many applications (e.g., wearable and implantable health monitors, drug delivery devices, and prosthetics) mechanically flexible polymer devices and systems that can conform to the body offer benefits that cannot be achieved using systems based on conventional rigid substrate materials. However, difficulties in implementing active devices and reliable packaging technologies have limited the success of flexible microfluidics. Employing highly compliant materials such as PDMS that are typically employed for prototyping, we review mechanically flexible polymer microfluidic technologies based on free-standing polymer substrates and novel electronic and microfluidic interconnection schemes. Central to these new technologies are hybrid microfabrication methods employing novel nanocomposite polymer materials and devices. We review microfabrication methods using these materials, along with demonstrations of example devices and packaging schemes that employ them. We review these recent developments and place them in the context of the fields of flexible microfluidics and conformable systems, and discuss cross-over applications to conventional rigid-substrate microfluidics.

Multichannel Interdiffusion Driven FASnI3 Film Formation Using Aqueous Hybrid Salt/Polymer Solutions toward Flexible Lead-Free Perovskite Solar Cells.

PubMed

Xi, Jun; Wu, Zhaoxin; Jiao, Bo; Dong, Hua; Ran, Chenxin; Piao, Chengcheng; Lei, Ting; Song, Tze-Bin; Ke, Weijun; Yokoyama, Takamichi; Hou, Xun; Kanatzidis, Mercouri G

2017-06-01

Tin (Sn)-based perovskites are increasingly attractive because they offer lead-free alternatives in perovskite solar cells. However, depositing high-quality Sn-based perovskite films is still a challenge, particularly for low-temperature planar heterojunction (PHJ) devices. Here, a "multichannel interdiffusion" protocol is demonstrated by annealing stacked layers of aqueous solution deposited formamidinium iodide (FAI)/polymer layer followed with an evaporated SnI 2 layer to create uniform FASnI 3 films. In this protocol, tiny FAI crystals, significantly inhibited by the introduced polymer, can offer multiple interdiffusion pathways for complete reaction with SnI 2 . What is more, water, rather than traditional aprotic organic solvents, is used to dissolve the precursors. The best-performing FASnI 3 PHJ solar cell assembled by this protocol exhibits a power conversion efficiency (PCE) of 3.98%. In addition, a flexible FASnI 3 -based flexible solar cell assembled on a polyethylene naphthalate-indium tin oxide flexible substrate with a PCE of 3.12% is demonstrated. This novel interdiffusion process can help to further boost the performance of lead-free Sn-based perovskites. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

EZID: Long term identifiers made easy (Invited)

NASA Astrophysics Data System (ADS)

Starr, J.

2013-12-01

Scholarly research is producing ever increasing amounts of digital research data, and this data should be managed throughout the research life cycle both as part of good scientific practice, but also to comply with funder mandates, such as the 2013 OSTP Public Access Memo (http://www.whitehouse.gov/sites/default/files/microsites/ostp/ostp_public_access_memo_2013.pdf). By assigning unique and persistent identifiers to data objects, data managers can gain control and flexibility over what can be a daunting task. This is due to the fact that the objects can be moved to new locations without disruption to links, as long as the identifier target is maintained. EZID is a tool that makes assigning and maintaining unique, persistent identifiers easy. It was designed and built by California Digital Library (CDL) and has both a user interface and a RESTful API. EZID currently offers services for two globally unique, persistent identifier schemes: Digital Object Identifiers (DOIs) and Archival Resource Keys (ARKs). DOIs are identifiers originating from the publishing world and are in widespread use for journal articles. CDL is able to offer DOIs because of being a founding member of DataCite (http://www.datacite.org/), an international consortium established to provide easier access to scientific research data on the Internet. ARKs are identifiers originating from the library, archive and museum community. Like DOIs, they become persistent when the objects and identifier forwarding information is maintained. DOIs and ARKs have a key role in data management and, therefore, in data management plans. DOIs are the recommended identifier for use in data citation, and ARKs provide the maximum flexibility needed for data documentation and management throughout the early phases of a project. The two identifier schemes are able to be used together, and EZID is made to work with both. EZID clients, coming from education, research, government, and the private sector, are utilizing the tool for these use cases and more.

Investment Vehicles for School Funds.

ERIC Educational Resources Information Center

Holman, Paul C.

1987-01-01

School administrators are advised to invest school funds for maximum return, coupled with safety and flexibility. The advantages and disadvantages of a variety of investment instruments are explained. (MLF)

Flexible and mechanical strain resistant large area SERS active substrates

NASA Astrophysics Data System (ADS)

Singh, J. P.; Chu, Hsiaoyun; Abell, Justin; Tripp, Ralph A.; Zhao, Yiping

2012-05-01

We report a cost effective and facile way to synthesize flexible, uniform, and large area surface enhanced Raman scattering (SERS) substrates using an oblique angle deposition (OAD) technique. The flexible SERS substrates consist of 1 μm long, tilted silver nanocolumnar films deposited on flexible polydimethylsiloxane (PDMS) and polyethylene terephthalate (PET) sheets using OAD. The SERS enhancement activity of these flexible substrates was determined using 10-5 M trans-1,2-bis(4-pyridyl) ethylene (BPE) Raman probe molecules. The in situ SERS measurements on these flexible substrates under mechanical (tensile/bending) strain conditions were performed. Our results show that flexible SERS substrates can withstand a tensile strain (ε) value as high as 30% without losing SERS performance, whereas the similar bending strain decreases the SERS performance by about 13%. A cyclic tensile loading test on flexible PDMS SERS substrates at a pre-specified tensile strain (ε) value of 10% shows that the SERS intensity remains almost constant for more than 100 cycles. These disposable and flexible SERS substrates can be integrated with biological substances and offer a novel and practical method to facilitate biosensing applications.

Two-Arm Flexible Thermal Strap

NASA Technical Reports Server (NTRS)

Urquiza, Eugenio; Vasquez, Cristal; Rodriquez, Jose I.; Leland, Robert S.; VanGorp, Byron E.

2011-01-01

Airborne and space infrared cameras require highly flexible direct cooling of mechanically-sensitive focal planes. A thermal electric cooler is often used together with a thermal strap as a means to transport the thermal energy removed from the infrared detector. While effective, traditional thermal straps are only truly flexible in one direction. In this scenario, a cooling solution must be highly conductive, lightweight, able to operate within a vacuum, and highly flexible in all axes to accommodate adjustment of the focal plane while transmitting minimal force. A two-armed thermal strap using three end pieces and a twisted section offers enhanced elastic movement, significantly beyond the motion permitted by existing thermal straps. This design innovation allows for large elastic displacements in two planes and moderate elasticity in the third plane. By contrast, a more conventional strap of the same conductance offers less flexibility and asymmetrical elasticity. The two-arm configuration reduces the bending moment of inertia for a given conductance by creating the same cross-sectional area for thermal conduction, but with only half the thickness. This reduction in the thickness has a significant effect on the flexibility since there is a cubic relationship between the thickness and the rigidity or bending moment of inertia. The novelty of the technology lies in the mechanical design and manufacturing of the thermal strap. The enhanced flexibility will facilitate cooling of mechanically sensitive components (example: optical focal planes). This development is a significant contribution to the thermal cooling of optics. It is known to be especially important in the thermal control of optical focal planes due to their highly sensitive alignment requirements and mechanical sensitivity; however, many other applications exist including the cooling of gimbal-mounted components.

Highly Flexible and Planar Supercapacitors Using Graphite Flakes/Polypyrrole in Polymer Lapping Film.

PubMed

Raj, C Justin; Kim, Byung Chul; Cho, Won-Je; Lee, Won-gil; Jung, Sang-Don; Kim, Yong Hee; Park, Sang Yeop; Yu, Kook Hyun

2015-06-24

Flexible supercapacitor electrodes have been fabricated by simple fabrication technique using graphite nanoflakes on polymer lapping films as flexible substrate. An additional thin layer of conducting polymer polypyrrole over the electrode improved the surface conductivity and exhibited excellent electrochemical performances. Such capacitor films showed better energy density and power density with a maximum capacitance value of 37 mF cm(-2) in a half cell configuration using 1 M H2SO4 electrolyte, 23 mF cm(-2) in full cell, and 6 mF cm(-2) as planar cell configuration using poly(vinyl alcohol) (PVA)/phosphoric acid (H3PO4) solid state electrolyte. Moreover, the graphite nanoflakes/polypyrrole over polymer lapping film demonstrated good flexibility and cyclic stability.

The forming simulation of flexible glass with silt down draw method

NASA Astrophysics Data System (ADS)

Yansheng, Hou; Jinshu, Cheng; Junfeng, Kang; Jing, Cui

2018-03-01

The slit down draw method is the main manufacturing process of flexible glass. In this study, Flow3DTM software was used to simulate the process of drawing and thinning glass slits during the slit down draw process. The influence of glass viscosity, initial plate thickness and initial plate speed on the glass spreading process was studied. The maximum pull-down force that the root can bear is linearly proportional to the viscosity, the initial thickness of 1.3837 power and the initial plate speed, respectively. The best way to improve the tensile strength of flexible glass is to increase the viscosity. Flexible glass was more easily to obtain with low viscosity, low thickness and low drawing speed.

Intervertebral disc adaptation to wedging deformation.

PubMed

Stokes, Ian A F; Aronsson, David D; Clark, Katherine C; Roemhildt, Maria L

2006-01-01

Although scoliosis includes wedge deformities of both vertebrae and discs, little is known about the causes of the discal changes, and whether they result from mechanical influences on growth and/or remodelling. An external apparatus attached to transvertebral pins applied compression and 15 degrees of angulation to each of two adjacent young rat caudal intervertebral discs for 5 weeks (four animals), or for 10 weeks (four animals). Each week, micro-CT scanning documented the in vivo discal wedging. After euthanasia, tail segments (three vertebrae and the 2 angulated discs) were excised and their flexibility was measured over a range of lateral bending. The angle of maximum flexibility was recorded. Then discs were fixed in situ (with the external apparatus in place) and sectioned for polarized light microscopy. The disc-wedging deformity averaged 15 degrees initially, it averaged 20 degrees after 5 weeks, and then reduced to 10 degrees (in 10 week animals). The lateral bending flexibility showed a distinct maximum at an average of 1.1 degrees from the in vivo position in the 5-week animals, indicating structural remodeling of the discs almost to the deformed geometry. The 10-week animals had maximum flexibility at 1.4 degrees from the in vivo position (no significant difference between 5 and 10-week animals.) Collagen crimp angles [Cassidy et al., Conn Tiss Res 1989, 23:75-88] were not significantly different between convex and concave sides, again suggesting that remodeling had occurred. In a mechanically induced scoliosis deformity in skeletally immature rats, the intervertebral discs underwent remodeling within 5 weeks. This indicates that this animal model is suitable for studying adaptive wedging changes in human scoliosis.

Printing Highly Controlled Suspended Carbon Nanotube Network on Micro-patterned Superhydrophobic Flexible Surface

PubMed Central

Li, Bo; Wang, Xin; Jung, Hyun Young; Kim, Young Lae; Robinson, Jeremy T.; Zalalutdinov, Maxim; Hong, Sanghyun; Hao, Ji; Ajayan, Pulickel M.; Wan, Kai-Tak; Jung, Yung Joon

2015-01-01

Suspended single-walled carbon nanotubes (SWCNTs) offer unique functionalities for electronic and electromechanical systems. Due to their outstanding flexible nature, suspended SWCNT architectures have great potential for integration into flexible electronic systems. However, current techniques for integrating SWCNT architectures with flexible substrates are largely absent, especially in a manner that is both scalable and well controlled. Here, we present a new nanostructured transfer paradigm to print scalable and well-defined suspended nano/microscale SWCNT networks on 3D patterned flexible substrates with micro- to nanoscale precision. The underlying printing/transfer mechanism, as well as the mechanical, electromechanical, and mechanical resonance properties of the suspended SWCNTs are characterized, including identifying metrics relevant for reliable and sensitive device structures. Our approach represents a fast, scalable and general method for building suspended nano/micro SWCNT architectures suitable for flexible sensing and actuation systems. PMID:26511284

Printing Highly Controlled Suspended Carbon Nanotube Network on Micro-patterned Superhydrophobic Flexible Surface.

PubMed

Li, Bo; Wang, Xin; Jung, Hyun Young; Kim, Young Lae; Robinson, Jeremy T; Zalalutdinov, Maxim; Hong, Sanghyun; Hao, Ji; Ajayan, Pulickel M; Wan, Kai-Tak; Jung, Yung Joon

2015-10-29

Suspended single-walled carbon nanotubes (SWCNTs) offer unique functionalities for electronic and electromechanical systems. Due to their outstanding flexible nature, suspended SWCNT architectures have great potential for integration into flexible electronic systems. However, current techniques for integrating SWCNT architectures with flexible substrates are largely absent, especially in a manner that is both scalable and well controlled. Here, we present a new nanostructured transfer paradigm to print scalable and well-defined suspended nano/microscale SWCNT networks on 3D patterned flexible substrates with micro- to nanoscale precision. The underlying printing/transfer mechanism, as well as the mechanical, electromechanical, and mechanical resonance properties of the suspended SWCNTs are characterized, including identifying metrics relevant for reliable and sensitive device structures. Our approach represents a fast, scalable and general method for building suspended nano/micro SWCNT architectures suitable for flexible sensing and actuation systems.

Numerical Simulation of the Vortex-Induced Vibration of A Curved Flexible Riser in Shear Flow

NASA Astrophysics Data System (ADS)

Zhu, Hong-jun; Lin, Peng-zhi

2018-06-01

A series of fully three-dimensional (3D) numerical simulations of flow past a free-to-oscillate curved flexible riser in shear flow were conducted at Reynolds number of 185-1015. The numerical results obtained by the two-way fluid-structure interaction (FSI) simulations are in good agreement with the experimental results reported in the earlier study. It is further found that the frequency transition is out of phase not only in the inline (IL) and crossflow (CF) directions but also along the span direction. The mode competition leads to the non-zero nodes of the rootmean- square (RMS) amplitude and the relatively chaotic trajectories. The fluid-structure interaction is to some extent reflected by the transverse velocity of the ambient fluid, which reaches the maximum value when the riser reaches the equilibrium position. Moreover, the local maximum transverse velocities occur at the peak CF amplitudes, and the values are relatively large when the vibration is in the resonance regions. The 3D vortex columns are shed nearly parallel to the axis of the curved flexible riser. As the local Reynolds number increases from 0 at the bottom of the riser to the maximum value at the top, the wake undergoes a transition from a two-dimensional structure to a 3D one. More irregular small-scale vortices appeared at the wake region of the riser, undergoing large amplitude responses.

Community College Student Success in Online versus Equivalent Face-to-Face Courses

ERIC Educational Resources Information Center

Gregory, Cheri B.; Lampley, James H.

2016-01-01

As part of a nationwide effort to increase the postsecondary educational attainment levels of citizens, community colleges have expanded offerings of courses and programs to more effectively meet the needs of students. Online courses offer convenience and flexibility that traditional face-to-face classes do not. These features appeal to students…

Self-rolling and light-trapping in flexible quantum well–embedded nanomembranes for wide-angle infrared photodetectors

PubMed Central

Wang, Han; Zhen, Honglou; Li, Shilong; Jing, Youliang; Huang, Gaoshan; Mei, Yongfeng; Lu, Wei

2016-01-01

Three-dimensional (3D) design and manufacturing enable flexible nanomembranes to deliver unique properties and applications in flexible electronics, photovoltaics, and photonics. We demonstrate that a quantum well (QW)–embedded nanomembrane in a rolled-up geometry facilitates a 3D QW infrared photodetector (QWIP) device with enhanced responsivity and detectivity. Circular geometry of nanomembrane rolls provides the light coupling route; thus, there are no external light coupling structures, which are normally necessary for QWIPs. This 3D QWIP device under tube-based light-trapping mode presents broadband enhancement of coupling efficiency and omnidirectional detection under a wide incident angle (±70°), offering a unique solution to high-performance focal plane array. The winding number of these rolled-up QWIPs provides well-tunable blackbody photocurrents and responsivity. 3D self-assembly of functional nanomembranes offers a new path for high conversion efficiency between light and electricity in photodetectors, solar cells, and light-emitting diodes. PMID:27536723

Evolution of flexibility and rigidity in retaliatory punishment

PubMed Central

MacGlashan, James; Littman, Michael L.

2017-01-01

Natural selection designs some social behaviors to depend on flexible learning processes, whereas others are relatively rigid or reflexive. What determines the balance between these two approaches? We offer a detailed case study in the context of a two-player game with antisocial behavior and retaliatory punishment. We show that each player in this game—a “thief” and a “victim”—must balance two competing strategic interests. Flexibility is valuable because it allows adaptive differentiation in the face of diverse opponents. However, it is also risky because, in competitive games, it can produce systematically suboptimal behaviors. Using a combination of evolutionary analysis, reinforcement learning simulations, and behavioral experimentation, we show that the resolution to this tension—and the adaptation of social behavior in this game—hinges on the game’s learning dynamics. Our findings clarify punishment’s adaptive basis, offer a case study of the evolution of social preferences, and highlight an important connection between natural selection and learning in the resolution of social conflicts. PMID:28893996

Evolution of flexibility and rigidity in retaliatory punishment.

PubMed

Morris, Adam; MacGlashan, James; Littman, Michael L; Cushman, Fiery

2017-09-26

Natural selection designs some social behaviors to depend on flexible learning processes, whereas others are relatively rigid or reflexive. What determines the balance between these two approaches? We offer a detailed case study in the context of a two-player game with antisocial behavior and retaliatory punishment. We show that each player in this game-a "thief" and a "victim"-must balance two competing strategic interests. Flexibility is valuable because it allows adaptive differentiation in the face of diverse opponents. However, it is also risky because, in competitive games, it can produce systematically suboptimal behaviors. Using a combination of evolutionary analysis, reinforcement learning simulations, and behavioral experimentation, we show that the resolution to this tension-and the adaptation of social behavior in this game-hinges on the game's learning dynamics. Our findings clarify punishment's adaptive basis, offer a case study of the evolution of social preferences, and highlight an important connection between natural selection and learning in the resolution of social conflicts.

Flexible thin-film battery based on graphene-oxide embedded in solid polymer electrolyte

NASA Astrophysics Data System (ADS)

Kammoun, M.; Berg, S.; Ardebili, H.

2015-10-01

Enhanced safety of flexible batteries is an imperative objective due to the intimate interaction of such devices with human organs such as flexible batteries that are integrated with touch-screens or embedded in clothing or space suits. In this study, the fabrication and testing of a high performance thin-film Li-ion battery (LIB) is reported that is both flexible and relatively safer compared to the conventional electrolyte based batteries. The concept is facilitated by the use of solid polymer nanocomposite electrolyte, specifically, composed of polyethylene oxide (PEO) matrix and 1 wt% graphene oxide (GO) nanosheets. The flexible LIB exhibits a high maximum operating voltage of 4.9 V, high capacity of 0.13 mA h cm-2 and an energy density of 4.8 mW h cm-3. The battery is encapsulated using a simple lamination method that is economical and scalable. The laminated battery shows robust mechanical flexibility over 6000 bending cycles and excellent electrochemical performance in both flat and bent configurations. Finite element analysis (FEA) of the LIB provides critical insights into the evolution of mechanical stresses during lamination and bending.Enhanced safety of flexible batteries is an imperative objective due to the intimate interaction of such devices with human organs such as flexible batteries that are integrated with touch-screens or embedded in clothing or space suits. In this study, the fabrication and testing of a high performance thin-film Li-ion battery (LIB) is reported that is both flexible and relatively safer compared to the conventional electrolyte based batteries. The concept is facilitated by the use of solid polymer nanocomposite electrolyte, specifically, composed of polyethylene oxide (PEO) matrix and 1 wt% graphene oxide (GO) nanosheets. The flexible LIB exhibits a high maximum operating voltage of 4.9 V, high capacity of 0.13 mA h cm-2 and an energy density of 4.8 mW h cm-3. The battery is encapsulated using a simple lamination method that is economical and scalable. The laminated battery shows robust mechanical flexibility over 6000 bending cycles and excellent electrochemical performance in both flat and bent configurations. Finite element analysis (FEA) of the LIB provides critical insights into the evolution of mechanical stresses during lamination and bending. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr04339e

Agriculture

EPA Pesticide Factsheets

The EPA Agriculture Resource Directory offers comprehensive, easy-to-understand information about environmental stewardship on farms and ranches; commonsense, flexible approaches that are both environmentally protective and agriculturally sound.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milligan, Michael; Bloom, Aaron P; Townsend, Aaron

Defining flexibility has been a challenge that a number of industry members and researchers have attempted to address in recent years. With increased variability and uncertainty of variable generation (VG), the resources on the system will have to be more flexible to adjust output, so that power output ranges, power ramp rates, and energy duration sustainability are sufficient to meet the needs of balancing supply with demand at various operational timescales. This chapter discusses whether existing market designs provide adequate incentives for resources to offer their flexibility into the market to meet the increased levels of variability and uncertainty introducedmore » by VG in the short-term operational time frame. It presents a definition of flexibility and discusses how increased levels of VG require increased needs for flexibility on power systems. Following this introductory material, the chapter examines how existing market designs ensure that resources have the right incentives to provide increased flexibility, and then discusses a number of emerging market design elements that impact flexibility incentives.« less

A Model for an Open and Flexible E-Training Platform To Encourage Companies' Learning Culture and Meet Employees' Learning Needs.

ERIC Educational Resources Information Center

Bagnasco, Andrea; Chirico, Marco; Parodi, Giancarlo; Scapolla, A. Marina

2003-01-01

Distance education is an answer to the demand for flexibility in training. The aim is to build a virtual learning community on the basis of a knowledge model that meets different learning needs. This article analyzes possible innovations in corporate training, and proposes a framework that integrates all information sources and offers practice…

Photogrammetric Verification of Fiber Optic Shape Sensors on Flexible Aerospace Structures

NASA Technical Reports Server (NTRS)

Moore, Jason P.; Rogge, Matthew D.; Jones, Thomas W.

2012-01-01

Multi-core fiber (MCF) optic shape sensing offers the possibility of providing in-flight shape measurements of highly flexible aerospace structures and control surfaces for such purposes as gust load alleviation, flutter suppression, general flight control and structural health monitoring. Photogrammetric measurements of surface mounted MCF shape sensing cable can be used to quantify the MCF installation path and verify measurement methods.

Defense Infrastructure: In-Kind Construction and Renovation Projects Initiated by DOD during Fiscal Year 2013

DTIC Science & Technology

2015-09-01

property conveyed by the Navy. Installation officials generally have more flexibility in real-estate transactions. According to officials of the...Air Force Civil Engineer Center, in-kind payment projects offer installation officials greater flexibility in executing real-estate transactions...air conditioning, fire protection, utility connections, pavement , and information systems. Agreement between Army and Air Force Exchange Services

Propulsion via flexible flapping in granular media

NASA Astrophysics Data System (ADS)

Peng, Zhiwei; Ding, Yang; Pietrzyk, Kyle; Elfring, Gwynn J.; Pak, On Shun

2017-07-01

Biological locomotion in nature is often achieved by the interaction between a flexible body and its surrounding medium. The interaction of a flexible body with granular media is less understood compared with viscous fluids partially due to its complex rheological properties. In this work, we explore the effect of flexibility on granular propulsion by considering a simple mechanical model in which a rigid rod is connected to a torsional spring that is under a displacement actuation using a granular resistive force theory. Through a combined numerical and asymptotic investigation, we characterize the propulsive dynamics of such a flexible flapper in relation to the actuation amplitude and spring stiffness, and we compare these dynamics with those observed in a viscous fluid. In addition, we demonstrate that the maximum possible propulsive force can be obtained in the steady propulsion limit with a finite spring stiffness and large actuation amplitude. These results may apply to the development of synthetic locomotive systems that exploit flexibility to move through complex terrestrial media.

Real-time Nyquist signaling with dynamic precision and flexible non-integer oversampling.

PubMed

Schmogrow, R; Meyer, M; Schindler, P C; Nebendahl, B; Dreschmann, M; Meyer, J; Josten, A; Hillerkuss, D; Ben-Ezra, S; Becker, J; Koos, C; Freude, W; Leuthold, J

2014-01-13

We demonstrate two efficient processing techniques for Nyquist signals, namely computation of signals using dynamic precision as well as arbitrary rational oversampling factors. With these techniques along with massively parallel processing it becomes possible to generate and receive high data rate Nyquist signals with flexible symbol rates and bandwidths, a feature which is highly desirable for novel flexgrid networks. We achieved maximum bit rates of 252 Gbit/s in real-time.

Scientific Analysis and Documentation Provided by EPA Regional Labs

EPA Pesticide Factsheets

The 10 EPA Regional laboratories provide maximum flexibility to support Agency response to natural disasters and emergencies by developing effective approaches for a wide range of analytical challenges.

H-TiO(2) @MnO(2) //H-TiO(2) @C core-shell nanowires for high performance and flexible asymmetric supercapacitors.

PubMed

Lu, Xihong; Yu, Minghao; Wang, Gongming; Zhai, Teng; Xie, Shilei; Ling, Yichuan; Tong, Yexiang; Li, Yat

2013-01-11

A flexible solid-state asymmetric supercapacitor device with H-TiO(2) @MnO(2) core-shell NWs as the positive electrode and H-TiO(2) @C core-shell NWs as the negative electrode is developed. This device operates in a 1.8 V voltage window and is able to deliver a high specific capacitance of 139.6 F g(-1) and maximum volumetric energy density of 0.30 mWh cm(-3) with excellent cycling performance and good flexibility. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Towards Collaboration as Learning: Evaluation of an Open CPD Opportunity for HE Teachers

ERIC Educational Resources Information Center

Nerantzi, Chrissi; Gossman, Peter

2015-01-01

Flexible, Distance and Online Learning (FDOL) is an open online course offered as an informal cross-institutional collaboration based on a postgraduate module in the context of teacher education in higher education. The second iteration, FDOL132, was offered in 2013 using a problem-based learning (PBL) design (FISh) to foster collaborative…

Relationship between Course Length and Graduate Student Outcome Measures

ERIC Educational Resources Information Center

Carman, Carol A.; Bartsch, Robert A.

2017-01-01

One method to increase flexibility in class offerings is through the use of compressed courses, classes that have the same number of contact hours but over a shorter time period (e.g., 8 weeks vs. 15 weeks). Before offering these courses, it is important to determine whether they lead to equivalent or better student outcomes. This study examined…

Student Loans Driving You Crazy? A Borrower's Guide to Direct Consolidation Loans.

ERIC Educational Resources Information Center

Office of Federal Student Aid (ED), Washington, DC.

This booklet describes the Direct Consolidation Loan program students can use to combine one or more student loans into a new loan. Things to consider before seeking a consolidation loan are outlined. Direct consolidation loans offer a number of advantages; they are free, result in one lender and one monthly payment, and offer flexible repayment…

Private University and Community College Strategic Alliances: The Case for Cooperation.

ERIC Educational Resources Information Center

Fincher, Mark

2002-01-01

Reviews the literature on community colleges and private universities, applying principles of strategic management to these environments. States that private universities have the flexibility to offer a specialized program of study at a premium price, while community colleges are better able to offer low-cost services to a large group of students.…

Advanced and flexible multi-carrier receiver architecture for high-count multi-core fiber based space division multiplexed applications

PubMed Central

Asif, Rameez

2016-01-01

Space division multiplexing (SDM), incorporating multi-core fibers (MCFs), has been demonstrated for effectively maximizing the data capacity in an impending capacity crunch. To achieve high spectral-density through multi-carrier encoding while simultaneously maintaining transmission reach, benefits from inter-core crosstalk (XT) and non-linear compensation must be utilized. In this report, we propose a proof-of-concept unified receiver architecture that jointly compensates optical Kerr effects, intra- and inter-core XT in MCFs. The architecture is analysed in multi-channel 512 Gbit/s dual-carrier DP-16QAM system over 800 km 19-core MCF to validate the digital compensation of inter-core XT. Through this architecture: (a) we efficiently compensates the inter-core XT improving Q-factor by 4.82 dB and (b) achieve a momentous gain in transmission reach, increasing the maximum achievable distance from 480 km to 1208 km, via analytical analysis. Simulation results confirm that inter-core XT distortions are more relentless for cores fabricated around the central axis of cladding. Predominantly, XT induced Q-penalty can be suppressed to be less than 1 dB up-to −11.56 dB of inter-core XT over 800 km MCF, offering flexibility to fabricate dense core structures with same cladding diameter. Moreover, this report outlines the relationship between core pitch and forward-error correction (FEC). PMID:27270381

Uncharted territories of the patent-restoration due-diligence challenge.

PubMed

Gaudry, Kate S

2011-01-01

The innovation and development incentives offered by the patent system are mitigated if a substantial portion of the patent term is lost while obtaining product approval through the Food and Drug Administration (FDA). The Drug Price Competition and Patent Restoration Act was enacted to return some of the lost patent term to the patentee. However, any person can petition the FDA, contending that the patentee did not act with due diligence in seeking FDA approval of the product during the regulatory review period. A successful challenge will reduce the restored term, such that the patentee is not compensated for time lost due to his own non-diligent actions. While the current due-diligence regulations provide a vague and flexible standard, earlier drafts of the regulations and FDA responses to comments provide insight as to the types of factors the FDA is likely to consider when assessing an applicant's diligence. A due-diligence petition has only been filed three times, and in none of these cases did the FDA issue a decision based on substantive diligence matters. Still, detailed examination of these petitions is also instructive in predicting the success of due-diligence challenges. Statute-imposed maximums and applicants' own incentives to act diligently may minimize the utility of the due-diligence challenges in some contexts. However, in other contexts, I propose that these petitions offer a feasible approach towards limiting pharmaceutical monopolies.

Morphing hybrid honeycomb (MOHYCOMB) with in situ Poisson’s ratio modulation

NASA Astrophysics Data System (ADS)

Heath, Callum J. C.; Neville, Robin M.; Scarpa, Fabrizio; Bond, Ian P.; Potter, Kevin D.

2016-08-01

Electrostatic adhesion can be used as a means of reversible attachment. Through application of high voltage (~2 kV) across closely spaced parallel plate electrodes, significant shear stresses (11 kPa) can be generated. The highest levels of electrostatic holding force can be achieved through close contact of connection surfaces; this is facilitated by flexible electrodes which can conform to reduce air gaps. Cellular structures are comprised of thin walled elements, making them ideal host structures for electrostatic adhesive elements. The reversible adhesion provides control of the internal connectivity of the cellular structure, and determines the effective cell geometry. This would offer variable stiffness and control of the effective Poisson’s ratio of the global cellular array. Using copper-polyimide thin film laminates and PVDF thin film dielectrics, double lap shear electrostatic adhesive elements have been introduced to a cellular geometry. By activating different groups of reversible adhesive interfaces, the cellular array can assume four different cell configurations. A maximum stiffness modulation of 450% between the ‘All off’ and ‘All on’ cell morphologies has been demonstrated. This structure is also capable of in situ effective Poisson’s ratio variations, with the ability to switch between values of -0.45 and 0.54. Such a structure offers the potential for tuneable vibration absorption (due to its variable stiffness properties), or as a smart honeycomb with controllable curvature and is termed morphing hybrid honeycomb.

Piaget and Microcomputer Learning Environments.

ERIC Educational Resources Information Center

Hofmann, Rich

1986-01-01

Four studies are offered from a Piagetian perspective on providing children with an optimal microcomputer environment. Guidelines stress the importance of flexibility, and a hierarchical software environment. (CL)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hurlbut, David; Zhou, Ella; Bird, Lori

A strategically planned transmission network is an important source of flexibility for the integration of large-scale renewable energy (RE). Such a network can offer access to a broad geographic diversity of resources, which can reduce flexibility needs and facilitate sharing between neighboring balancing areas. This report builds on two previous NREL technical reports - Advancing System Flexibility for High Penetration Renewable Integration (Milligan et al. 2015) and 'Renewables-Friendly' Grid Development Strategies (Hurlbut et al. 2015) - which discuss various flexibility options and provide an overview of U.S. market models and grid planning. This report focuses on addressing issues with cross-regional/provincialmore » transmission in China with the aim of integrating renewable resources that are concentrated in remote areas and require inter-regional/provincial power exchange.« less

Cognitive flexibility and religious disbelief.

PubMed

Zmigrod, Leor; Rentfrow, P Jason; Zmigrod, Sharon; Robbins, Trevor W

2018-06-11

Cognitive flexibility is operationalized in the neuropsychological literature as the ability to shift between modes of thinking and adapt to novel or changing environments. Religious belief systems consist of strict rules and rituals that offer adherents certainty, consistency, and stability. Consequently, we hypothesized that religious adherence and practice of repetitive religious rituals may be related to the persistence versus flexibility of one's cognition. The present study investigated the extent to which tendencies towards cognitive flexibility versus persistence are related to three facets of religious life: religious affiliation, religious practice, and religious upbringing. In a large sample (N = 744), we found that religious disbelief was related to cognitive flexibility across three independent behavioural measures: the Wisconsin Card Sorting Test, Remote Associates Test, and Alternative Uses Test. Furthermore, lower frequency of religious service attendance was related to cognitive flexibility. When analysing participants' religious upbringing in relation to their current religious affiliation, it was manifest that current affiliation was more influential than religious upbringing in all the measured facets of cognitive flexibility. The findings indicate that religious affiliation and engagement may shape and be shaped by cognitive control styles towards flexibility versus persistence, highlighting the tight links between flexibility of thought and religious ideologies.

Controlling Flexible Manipulators, an Experimental Investigation. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Hastings, Gordon Greene

1986-01-01

Lightweight, slender manipulators offer faster response and/or greater workspace range for the same size actuators than tradional manipulators. Lightweight construction of manipulator links results in increased structural flexibility. The increase flexibility must be considered in the design of control systems to properly account for the dynamic flexible vibrations and static deflections. Real time control of the flexible manipulator vibrations are experimentally investigated. Models intended for real-time control of distributed parameter system such as flexible manipulators rely on model approximation schemes. An linear model based on the application of Lagrangian dynamics to a rigid body mode and a series of separable flexible modes is examined with respect to model order requirements, and modal candidate selection. Balanced realizations are applied to the linear flexible model to obtain an estimate of appropriate order for a selected model. Describing the flexible deflections as a linear combination of modes results in measurements of beam state, which yield information about several modes. To realize the potential of linear systems theory, knowledge of each state must be available. State estimation is also accomplished by implementation of a Kalman Filter. State feedback control laws are implemented based upon linear quadratic regulator design.

A Modular Approach To Developing A Large Deployable Reflector

NASA Astrophysics Data System (ADS)

Pittman, R.; Leidich, C.; Mascy, F.; Swenson, B.

1984-01-01

NASA is currently studying the feasibility of developing a Large Deployable Reflector (LDR) astronomical facility to perform astrophysical studies of the infrared and submillimeter portion of the spectrum in the mid 1990's. The LDR concept was recommended by the Astronomy Survey Committee of the National Academy of Sciences as one of two space based projects to be started this decade. The current baseline calls for a 20 m (65.6 ft) aperture telescope diffraction limited at 30 μm and automatically deployed from a single Shuttle launch. The volume, performance, and single launch constraints place great demands on the technology and place LDR beyond the state-of-the-art in certain areas such as lightweight reflector segments. The advent of the Shuttle is opening up many new options and capabilities for producing large space systems. Until now, LDR has always been conceived as an integrated system, deployed autonomously in a single launch. This paper will look at a combination of automatic deployment and on-orbit assembly that may reduce the technological complexity and cost of the LDR system. Many technological tools are now in use or under study that will greatly enhance our capabilities to do assembly in space. Two Shuttle volume budget scenarios will be examined to assess the potential of these tools to reduce the LDR system complexity. Further study will be required to reach the full optimal combination of deployment and assembly, since in most cases the capabilities of these new tools have not been demonstrated. In order to take maximum advantage of these concepts, the design of LDR must be flexible and allow one subsystem to be modified without adversely affecting the entire system. One method of achieving this flexibility is to use a modular design approach in which the major subsystems are physically separated during launch and assembled on orbit. A modular design approach facilitates this flexibility but requires that the subsystems be interfaced in a simple, straightforward, and controlled manner. NASA is currently defining a technology development plan for LDR which will identify the technology advances that are required. The modular approach offers the flexibility to easily incorporate these new advances into the design.

Additive equivalence in turbulent drag reduction by flexible and rodlike polymers.

PubMed

Benzi, Roberto; Ching, Emily S C; Lo, T S; L'vov, Victor S; Procaccia, Itamar

2005-07-01

We address the additive equivalence discovered by Virk and co-workers: drag reduction affected by flexible and rigid rodlike polymers added to turbulent wall-bounded flows is limited from above by a very similar maximum drag reduction (MDR) asymptote. Considering the equations of motion of rodlike polymers in wall-bounded turbulent ensembles, we show that although the microscopic mechanism of attaining the MDR is very different, the macroscopic theory is isomorphic, rationalizing the interesting experimental observations.

Operation DOMINIC, SHOT SWORD FISH. Scientific Director’s Summary Report

DTIC Science & Technology

1985-09-01

charges, undoubtedly reflects a design decision that balanced thp tactical need for flexibility in using the weapon against the desire to ensure...further if the commanding officer is to take maximum advantage of his increased weapon delivery flexibility . i.2 SIGNIFICANCE OF SWORD FISH AS AN...turn, is governed by the pulsation and upward z.gration of the steam bubble formed in the water after the burst. The base surge, at ranges of delivery

Flexible and multi-directional piezoelectric energy harvester for self-powered human motion sensor

NASA Astrophysics Data System (ADS)

Kim, Min-Ook; Pyo, Soonjae; Oh, Yongkeun; Kang, Yunsung; Cho, Kyung-Ho; Choi, Jungwook; Kim, Jongbaeg

2018-03-01

A flexible piezoelectric strain energy harvester that is responsive to multi-directional input forces produced by various human motions is proposed. The structure of the harvester, which includes a polydimethylsiloxane (PDMS) bump, facilitates the effective conversion of strain energy, produced by input forces applied in random directions, into electrical energy. The structural design of the PDMS bump and frame as well as the slits in the piezoelectric polyvinylidene fluoride (PVDF) film provide mechanical flexibility and enhance the strain induced in the PVDF film under input forces applied at various angles. The amount and direction of the strain induced in PVDF can be changed by the direction of the applied force; thus, the generated output power can be varied. The measured maximum output peak voltage is 1.75, 1.29, and 0.98 V when an input force of 4 N (2 Hz) is applied at angles of 0°, 45°, and 90°, and the corresponding maximum output power is 0.064, 0.026, and 0.02 μW, respectively. Moreover, the harvester stably generates output voltage over 1.4 × 104 cycles. Thus, the proposed harvester successfully identifies and converts strain energy produced by multi-directional input forces by various human motions into electrical energy. We demonstrate the potential utility of the proposed flexible energy harvester as a self-powered human motion sensor for wireless healthcare systems.

Deformable inorganic semiconductor

NASA Astrophysics Data System (ADS)

Kim, Dae-Hyeong; Cha, Gi Doo

2018-05-01

Unlike conventional inorganic semiconductors, which are typically brittle, α-Ag2S exhibits room-temperature ductility with favourable electrical properties, offering promise for use in high-performance flexible and stretchable devices.

Computing the Envelope for Stepwise-Constant Resource Allocations

NASA Technical Reports Server (NTRS)

Muscettola, Nicola; Clancy, Daniel (Technical Monitor)

2002-01-01

Computing tight resource-level bounds is a fundamental problem in the construction of flexible plans with resource utilization. In this paper we describe an efficient algorithm that builds a resource envelope, the tightest possible such bound. The algorithm is based on transforming the temporal network of resource consuming and producing events into a flow network with nodes equal to the events and edges equal to the necessary predecessor links between events. A staged maximum flow problem on the network is then used to compute the time of occurrence and the height of each step of the resource envelope profile. Each stage has the same computational complexity of solving a maximum flow problem on the entire flow network. This makes this method computationally feasible and promising for use in the inner loop of flexible-time scheduling algorithms.

Evidence for a maximum mass cut-off in the neutron star mass distribution and constraints on the equation of state

NASA Astrophysics Data System (ADS)

Alsing, Justin; Silva, Hector O.; Berti, Emanuele

2018-04-01

We infer the mass distribution of neutron stars in binary systems using a flexible Gaussian mixture model and use Bayesian model selection to explore evidence for multi-modality and a sharp cut-off in the mass distribution. We find overwhelming evidence for a bimodal distribution, in agreement with previous literature, and report for the first time positive evidence for a sharp cut-off at a maximum neutron star mass. We measure the maximum mass to be 2.0M⊙ < mmax < 2.2M⊙ (68%), 2.0M⊙ < mmax < 2.6M⊙ (90%), and evidence for a cut-off is robust against the choice of model for the mass distribution and to removing the most extreme (highest mass) neutron stars from the dataset. If this sharp cut-off is interpreted as the maximum stable neutron star mass allowed by the equation of state of dense matter, our measurement puts constraints on the equation of state. For a set of realistic equations of state that support >2M⊙ neutron stars, our inference of mmax is able to distinguish between models at odds ratios of up to 12: 1, whilst under a flexible piecewise polytropic equation of state model our maximum mass measurement improves constraints on the pressure at 3 - 7 × the nuclear saturation density by ˜30 - 50% compared to simply requiring mmax > 2M⊙. We obtain a lower bound on the maximum sound speed attained inside the neutron star of c_s^max > 0.63c (99.8%), ruling out c_s^max < c/√{3} at high significance. Our constraints on the maximum neutron star mass strengthen the case for neutron star-neutron star mergers as the primary source of short gamma-ray bursts.

High-efficiency robust perovskite solar cells on ultrathin flexible substrates

PubMed Central

Li, Yaowen; Meng, Lei; Yang, Yang (Michael); Xu, Guiying; Hong, Ziruo; Chen, Qi; You, Jingbi; Li, Gang; Yang, Yang; Li, Yongfang

2016-01-01

Wide applications of personal consumer electronics have triggered tremendous need for portable power sources featuring light-weight and mechanical flexibility. Perovskite solar cells offer a compelling combination of low-cost and high device performance. Here we demonstrate high-performance planar heterojunction perovskite solar cells constructed on highly flexible and ultrathin silver-mesh/conducting polymer substrates. The device performance is comparable to that of their counterparts on rigid glass/indium tin oxide substrates, reaching a power conversion efficiency of 14.0%, while the specific power (the ratio of power to device weight) reaches 1.96 kW kg−1, given the fact that the device is constructed on a 57-μm-thick polyethylene terephthalate based substrate. The flexible device also demonstrates excellent robustness against mechanical deformation, retaining >95% of its original efficiency after 5,000 times fully bending. Our results confirmed that perovskite thin films are fully compatible with our flexible substrates, and are thus promising for future applications in flexible and bendable solar cells. PMID:26750664

Printable inorganic nanomaterials for flexible transparent electrodes: from synthesis to application

NASA Astrophysics Data System (ADS)

Wang, Dingrun; Mei, Yongfeng; Huang, Gaoshan

2018-01-01

Printed and flexible electronics are definitely promising cutting-edge electronic technologies of the future. They offer a wide-variety of applications such as flexible circuits, flexible displays, flexible solar cells, skin-like pressure sensors, and radio frequency identification tags in our daily life. As the most-fundamental component of electronics, electrodes are made of conductive materials that play a key role in flexible and printed electronic devices. In this review, various inorganic conductive materials and strategies for obtaining highly conductive and uniform electrodes are demonstrated. Applications of printed electrodes fabricated via these strategies are also described. Nevertheless, there are a number of challenges yet to overcome to optimize the processing and performance of printed electrodes. Project supported by the National Natural Science Foundation of China (Nos. 51475093, U1632115), the Science and Technology Commission of Shanghai Municipality (No. 14JC1400200), the National Key Technologies R&D Program of China (No. 2015ZX02102-003), and the Changjiang Young Scholars Programme of China.

Development of Flexible Multilayer Circuits and Cables

NASA Technical Reports Server (NTRS)

Barnes, Kevin N.; Bryant, Robert; Holloway, Nancy; Draughon, Fred

2005-01-01

A continuing program addresses the development of flexible multilayer electronic circuits and associated flexible cables. This development is undertaken to help satisfy aerospace-system-engineering requirements for efficient, lightweight electrical and electronic subsystems that can fit within confined spaces, adhere to complexly shaped surfaces, and can be embedded within composite materials. Heretofore, substrate layers for commercial flexible circuitry have been made from sheets of Kapton (or equivalent) polyimide and have been bonded to copper conductors and to other substrate layers by means of adhesives. The substrates for the present developmental flexible circuitry are made from thin films of a polyimide known as LaRC(TM)-SI. This polyimide is thermoplastic and, therefore, offers the potential to eliminate delamination and the need for adhesives. The development work undertaken thus far includes experiments in the use of several techniques of design and fabrication (including computer-aided design and fabrication) of representative flexible circuits. Anticipated future efforts would focus on multilayer bonding, fabrication of prototypes, and overcoming limitations.

Development of flexible rotor balancing criteria

NASA Technical Reports Server (NTRS)

Walter, W. W.; Rieger, N. F.

1979-01-01

Several studies in which analytical procedures were used to obtain balancing criteria for flexible rotors are described. General response data for a uniform rotor in damped flexible supports were first obtained for plain cylindrical bearings, tilting pad bearings, axial groove bearings, and partial arc bearings. These data formed the basis for the flexible rotor balance criteria presented. A procedure by which a practical rotor in bearings could be reduced to an equivalent uniform rotor was developed and tested. It was found that the equivalent rotor response always exceeded to practical rotor response by more than sixty percent for the cases tested. The equivalent rotor procedure was then tested against six practical rotor configurations for which data was available. It was found that the equivalent rotor method offered a procedure by which balance criteria could be selected for practical flexible rotors, using the charts given for the uniform rotor.

Flexible single-incision surgery: a fusion technique.

PubMed

Noguera, José F; Dolz, Carlos; Cuadrado, Angel; Olea, José; García, Juan

2013-06-01

The development of natural orifice transluminal endoscopic surgery has led to other techniques, such as single-incision surgery. The use of the flexible endoscope for single-incision surgery paves the way for further refinement of both surgical methods. To describe a new, single-incision surgical technique, namely, flexible single-incision surgery. Assessment of the safety and effectiveness of endoscopic cholecystectomy in a series of 30 patients. This technique consists of a single umbilical incision through which a flexible endoscope is introduced and consists of 2 parallel entry ports that provide access to nonarticulated laparoscopic instruments. The technique was applied in all patients for whom it was prescribed. No general or surgical wound complications were noted. Surgical time was no longer than usual for single-port surgery. Flexible single-incision surgery is a new single-site surgical technique offering the same level of patient safety, with additional advantages for the surgeon at minimal cost.

A Comparison of the Performance of Online versus Traditional On-Campus Earth Science Students on Identical Exams

ERIC Educational Resources Information Center

Werhner, Matthew J.

2010-01-01

In this paper I compare the performance of online versus traditional on-campus students on identical exams in an earth science class. The number of college level distance learning classes offered online continues to increase as they offer greater scheduling flexibility to students, they appeal to students who like to work independently, and allow…

A cloud-based production system for information and service integration: an internet of things case study on waste electronics

NASA Astrophysics Data System (ADS)

Wang, Xi Vincent; Wang, Lihui

2017-08-01

Cloud computing is the new enabling technology that offers centralised computing, flexible data storage and scalable services. In the manufacturing context, it is possible to utilise the Cloud technology to integrate and provide industrial resources and capabilities in terms of Cloud services. In this paper, a function block-based integration mechanism is developed to connect various types of production resources. A Cloud-based architecture is also deployed to offer a service pool which maintains these resources as production services. The proposed system provides a flexible and integrated information environment for the Cloud-based production system. As a specific type of manufacturing, Waste Electrical and Electronic Equipment (WEEE) remanufacturing experiences difficulties in system integration, information exchange and resource management. In this research, WEEE is selected as the example of Internet of Things to demonstrate how the obstacles and bottlenecks are overcome with the help of Cloud-based informatics approach. In the case studies, the WEEE recycle/recovery capabilities are also integrated and deployed as flexible Cloud services. Supporting mechanisms and technologies are presented and evaluated towards the end of the paper.

A universal data access and protocol integration mechanism for smart home

NASA Astrophysics Data System (ADS)

Shao, Pengfei; Yang, Qi; Zhang, Xuan

2013-03-01

With the lack of standardized or completely missing communication interfaces in home electronics, there is no perfect solution to address every aspect in smart homes based on existing protocols and technologies. In addition, the central control unit (CCU) of smart home system working point-to-point between the multiple application interfaces and the underlying hardware interfaces leads to its complicated architecture and unpleasant performance. A flexible data access and protocol integration mechanism is required. The current paper offers a universal, comprehensive data access and protocol integration mechanism for a smart home. The universal mechanism works as a middleware adapter with unified agreements of the communication interfaces and protocols, offers an abstraction of the application level from the hardware specific and decoupling the hardware interface modules from the application level. Further abstraction for the application interfaces and the underlying hardware interfaces are executed based on adaption layer to provide unified interfaces for more flexible user applications and hardware protocol integration. This new universal mechanism fundamentally changes the architecture of the smart home and in some way meets the practical requirement of smart homes more flexible and desirable.

The Effect of Fatigue Cracks on Fastener Flexibility, Load Distribution and Fatigue Crack Growth

DTIC Science & Technology

2012-05-01

fastener will transfer within a given fastener pattern. iv iv However, current methods do not account for the change in flexibility at a fastener...affects the growth of the crack. Thus, as the effect of the crack starts to impact the load transfer of the joint there is a need to account for...not account for spectrum loading but typically were cycled from 1g to limit or maximum flight load and then correlated to measured usage using

High Impulse Gun Airborne Demonstration. GAU-13/A Weapon, Feed System, Gun Drive and Electronic Controls.

DTIC Science & Technology

1981-05-01

made to provide mounting bosses for the closed loop conveyor chute . Ten small round bosses were welded onto the housing to provide this support...became necessary to depart from previous closed loop feeder designs . The original feed system consisted of a series of conveyor elements in a flexible...The flexible chuting has been replaced with rigid chuting forming a loop around the gun housing. This design affords the maximum stiffness and hence

43 CFR 3422.1 - Fair market value and maximum economic recovery.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Fair market value and maximum economic... Lease Sales § 3422.1 Fair market value and maximum economic recovery. (a) Not less than 30 days prior to... (FMV) appraisal and the maximum economic recovery (MER) of the tract or tracts proposed to be offered...

43 CFR 3422.1 - Fair market value and maximum economic recovery.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Fair market value and maximum economic... Lease Sales § 3422.1 Fair market value and maximum economic recovery. (a) Not less than 30 days prior to... (FMV) appraisal and the maximum economic recovery (MER) of the tract or tracts proposed to be offered...

43 CFR 3422.1 - Fair market value and maximum economic recovery.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Fair market value and maximum economic... Lease Sales § 3422.1 Fair market value and maximum economic recovery. (a) Not less than 30 days prior to... (FMV) appraisal and the maximum economic recovery (MER) of the tract or tracts proposed to be offered...

43 CFR 3422.1 - Fair market value and maximum economic recovery.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Fair market value and maximum economic... Lease Sales § 3422.1 Fair market value and maximum economic recovery. (a) Not less than 30 days prior to... (FMV) appraisal and the maximum economic recovery (MER) of the tract or tracts proposed to be offered...

Graphene/Pentacene Barristor with Ion-Gel Gate Dielectric: Flexible Ambipolar Transistor with High Mobility and On/Off Ratio.

PubMed

Oh, Gwangtaek; Kim, Jin-Soo; Jeon, Ji Hoon; Won, EunA; Son, Jong Wan; Lee, Duk Hyun; Kim, Cheol Kyeom; Jang, Jingon; Lee, Takhee; Park, Bae Ho

2015-07-28

High-quality channel layer is required for next-generation flexible electronic devices. Graphene is a good candidate due to its high carrier mobility and unique ambipolar transport characteristics but typically shows a low on/off ratio caused by gapless band structure. Popularly investigated organic semiconductors, such as pentacene, suffer from poor carrier mobility. Here, we propose a graphene/pentacene channel layer with high-k ion-gel gate dielectric. The graphene/pentacene device shows both high on/off ratio and carrier mobility as well as excellent mechanical flexibility. Most importantly, it reveals ambipolar behaviors and related negative differential resistance, which are controlled by external bias. Therefore, our graphene/pentacene barristor with ion-gel gate dielectric can offer various flexible device applications with high performances.

Robust, Flexible and Lightweight Dielectric Barrier Discharge Actuators Using Nanofoams/Aerogels

NASA Technical Reports Server (NTRS)

Siochi, Emilie J. (Inventor); Sauti, Godfrey (Inventor); Wilkinson, Stephen P. (Inventor); Guo, Haiquan N. (Inventor); Xu, Tian-Bing (Inventor); Meador, Mary Ann B. (Inventor)

2015-01-01

Robust, flexible, lightweight, low profile enhanced performance dielectric barrier discharge actuators (plasma actuators) based on aerogels/nanofoams with controlled pore size and size distribution as well as pore shape. The plasma actuators offer high body force as well as high force to weight ratios (thrust density). The flexibility and mechanical robustness of the actuators allows them to be shaped to conform to the surface to which they are applied. Carbon nanotube (CNT) based electrodes serve to further decrease the weight and profile of the actuators while maintaining flexibility while insulating nano-inclusions in the matrix enable tailoring of the mechanical properties. Such actuators are required for flow control in aeronautics and moving machinery such as wind turbines, noise abatement in landing gear and rotary wing aircraft and other applications.

All-solid-state flexible supercapacitors based on papers coated with carbon nanotubes and ionic-liquid-based gel electrolytes.

PubMed

Kang, Yu Jin; Chung, Haegeun; Han, Chi-Hwan; Kim, Woong

2012-02-17

All-solid-state flexible supercapacitors were fabricated using carbon nanotubes (CNTs), regular office papers, and ionic-liquid-based gel electrolytes. Flexible electrodes were made by coating CNTs on office papers by a drop-dry method. The gel electrolyte was prepared by mixing fumed silica nanopowders with ionic liquid, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMIM][NTf(2)]). This supercapacitor showed high power and energy performance as a solid-state flexible supercapacitor. The specific capacitance of the CNT electrodes was 135 F g(-1) at a current density of 2 A g(-1), when considering the mass of active materials only. The maximum power and energy density of the supercapacitors were 164 kW kg(-1) and 41 Wh kg(-1), respectively. Interestingly, the solid-state supercapacitor with the gel electrolyte showed comparable performance to the supercapacitors with ionic-liquid electrolyte. Moreover, the supercapacitor showed excellent stability and flexibility. The CNT/paper- and gel-based supercapacitors may hold great potential for low-cost and high-performance flexible energy storage applications.

All-solid-state flexible supercapacitors based on papers coated with carbon nanotubes and ionic-liquid-based gel electrolytes

NASA Astrophysics Data System (ADS)

Kang, Yu Jin; Chung, Haegeun; Han, Chi-Hwan; Kim, Woong

2012-02-01

All-solid-state flexible supercapacitors were fabricated using carbon nanotubes (CNTs), regular office papers, and ionic-liquid-based gel electrolytes. Flexible electrodes were made by coating CNTs on office papers by a drop-dry method. The gel electrolyte was prepared by mixing fumed silica nanopowders with ionic liquid, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMIM][NTf2]). This supercapacitor showed high power and energy performance as a solid-state flexible supercapacitor. The specific capacitance of the CNT electrodes was 135 F g-1 at a current density of 2 A g-1, when considering the mass of active materials only. The maximum power and energy density of the supercapacitors were 164 kW kg-1 and 41 Wh kg-1, respectively. Interestingly, the solid-state supercapacitor with the gel electrolyte showed comparable performance to the supercapacitors with ionic-liquid electrolyte. Moreover, the supercapacitor showed excellent stability and flexibility. The CNT/paper- and gel-based supercapacitors may hold great potential for low-cost and high-performance flexible energy storage applications.

Propulsion via flexible flapping in granular media

NASA Astrophysics Data System (ADS)

Peng, Zhiwei; Ding, Yang; Pietrzyk, Kyle; Elfring, Gwynn; Pak, On Shun

2017-11-01

Biological locomotion in nature is often achieved by the interaction between a flexible body and its surrounding medium. The interaction of a flexible body with granular media is less understood compared with viscous fluids partially due to its complex rheological properties. In this work, we explore the effect of flexibility on granular propulsion by considering a simple mechanical model in which a rigid rod is connected to a torsional spring that is under a displacement actuation using a granular resistive force theory. Through a combined numerical and asymptotic investigation, we characterize the propulsive dynamics of such a flexible flapper in relation to the actuation amplitude and spring stiffness, and we compare these dynamics with those observed in a viscous fluid. In addition, we demonstrate that the maximum possible propulsive force can be obtained in the steady propulsion limit with a finite spring stiffness and large actuation amplitude. These results may apply to the development of synthetic locomotive systems that exploit flexibility to move through complex terrestrial media. Funding for Z.P. and Y.D. was partially provided by NSFC 394 Grant No. 11672029 and NSAF-NSFC Grant No. U1530401.

High-performance flexible hydrogen sensor made of WS2 nanosheet-Pd nanoparticle composite film

NASA Astrophysics Data System (ADS)

Kuru, Cihan; Choi, Duyoung; Kargar, Alireza; Liu, Chin Hung; Yavuz, Serdar; Choi, Chulmin; Jin, Sungho; Bandaru, Prabhakar R.

2016-05-01

We report a flexible hydrogen sensor, composed of WS2 nanosheet-Pd nanoparticle composite film, fabricated on a flexible polyimide substrate. The sensor offers the advantages of light-weight, mechanical durability, room temperature operation, and high sensitivity. The WS2-Pd composite film exhibits sensitivity (R 1/R 2, the ratio of the initial resistance to final resistance of the sensor) of 7.8 to 50 000 ppm hydrogen. Moreover, the WS2-Pd composite film distinctly outperforms the graphene-Pd composite, whose sensitivity is only 1.14. Furthermore, the ease of fabrication holds great potential for scalable and low-cost manufacturing of hydrogen sensors.

Inter-Vertebral Flexibility of the Ostrich Neck: Implications for Estimating Sauropod Neck Flexibility

PubMed Central

Cobley, Matthew J.; Rayfield, Emily J.; Barrett, Paul M.

2013-01-01

The flexibility and posture of the neck in sauropod dinosaurs has long been contentious. Improved constraints on sauropod neck function will have major implications for what we know of their foraging strategies, ecology and overall biology. Several hypotheses have been proposed, based primarily on osteological data, suggesting different degrees of neck flexibility. This study attempts to assess the effects of reconstructed soft tissues on sauropod neck flexibility through systematic removal of muscle groups and measures of flexibility of the neck in a living analogue, the ostrich (Struthio camelus). The possible effect of cartilage on flexibility is also examined, as this was previously overlooked in osteological estimates of sauropod neck function. These comparisons show that soft tissues are likely to have limited the flexibility of the neck beyond the limits suggested by osteology alone. In addition, the inferred presence of cartilage, and varying the inter-vertebral spacing within the synovial capsule, also affect neck flexibility. One hypothesis proposed that flexibility is constrained by requiring a minimum overlap between successive zygapophyses equivalent to 50% of zygapophyseal articular surface length (ONP50). This assumption is tested by comparing the maximum flexibility of the articulated cervical column in ONP50 and the flexibility of the complete neck with all tissues intact. It is found that this model does not adequately convey the pattern of flexibility in the ostrich neck, suggesting that the ONP50 model may not be useful in determining neck function if considered in isolation from myological and other soft tissue data. PMID:23967284

Vapor-phase polymerization of poly(3, 4-ethylenedioxythiophene) nanofibers on carbon cloth as electrodes for flexible supercapacitors.

PubMed

Zhao, Xin; Dong, Mengyang; Zhang, Junxian; Li, Yingzhi; Zhang, Qinghua

2016-09-23

In this study, an evaporative vapor-phase polymerization approach was employed to fabricate vertically aligned poly(3, 4-ethylenedioxythiophene) (PEDOT) nanofibers on the surface of carbon cloth (CC). Optimized reaction conditions can obtain well distributed and uniform layers of high-aspect-ratio PEDOT nanofibers on CC. The hierarchical PEDOT/CC structure as a freestanding electrode exhibits good electrochemical properties. As a flexible symmetric supercapacitor, the PEDOT/CC hybrid electrode displays a specific areal capacitance of 201.4 mF cm(-2) at 1 mA cm(-2), good flexibility with a higher value (204.6 mF cm(-2)) in the bending state, and a good cycling stability of 92.4% after 1000 cycles. Moreover, the device shows a maximum energy density of 4.0 Wh kg(-1) (with a power density of 3.2 kW kg(-1)) and a maximum power density of 4.2 kW kg(-1) (with an energy density of 3.1 Wh kg(-1)). The results demonstrate that PEDOT may be a promising material for storage devices through a simple and efficient vapor-phase polymerization process with precisely controlled reaction conditions.

Vapor-phase polymerization of poly(3, 4-ethylenedioxythiophene) nanofibers on carbon cloth as electrodes for flexible supercapacitors

NASA Astrophysics Data System (ADS)

Zhao, Xin; Dong, Mengyang; Zhang, Junxian; Li, Yingzhi; Zhang, Qinghua

2016-09-01

In this study, an evaporative vapor-phase polymerization approach was employed to fabricate vertically aligned poly(3, 4-ethylenedioxythiophene) (PEDOT) nanofibers on the surface of carbon cloth (CC). Optimized reaction conditions can obtain well distributed and uniform layers of high-aspect-ratio PEDOT nanofibers on CC. The hierarchical PEDOT/CC structure as a freestanding electrode exhibits good electrochemical properties. As a flexible symmetric supercapacitor, the PEDOT/CC hybrid electrode displays a specific areal capacitance of 201.4 mF cm-2 at 1 mA cm-2, good flexibility with a higher value (204.6 mF cm-2) in the bending state, and a good cycling stability of 92.4% after 1000 cycles. Moreover, the device shows a maximum energy density of 4.0 Wh kg-1 (with a power density of 3.2 kW kg-1) and a maximum power density of 4.2 kW kg-1 (with an energy density of 3.1 Wh kg-1). The results demonstrate that PEDOT may be a promising material for storage devices through a simple and efficient vapor-phase polymerization process with precisely controlled reaction conditions.

Piezoelectric polymer multilayer on flexible substrate for energy harvesting.

PubMed

Zhang, Lei; Oh, Sharon Roslyn; Wong, Ting Chong; Tan, Chin Yaw; Yao, Kui

2013-09-01

A piezoelectric polymer multilayer structure formed on a flexible substrate is investigated for mechanical energy harvesting under bending mode. Analytical and numerical models are developed to clarify the effect of material parameters critical to the energy harvesting performance of the bending multilayer structure. It is shown that the maximum power is proportional to the square of the piezoelectric stress coefficient and the inverse of dielectric permittivity of the piezoelectric polymer. It is further found that a piezoelectric multilayer with thinner electrodes can generate more electric energy in bending mode. The effect of improved impedance matching in the multilayer polymer on energy output is remarkable. Comparisons between piezoelectric ceramic multilayers and polymer multilayers on flexible substrate are discussed. The fabrication of a P(VDF-TrFE) multilayer structure with a thin Al electrode layer is experimentally demonstrated by a scalable dip-coating process on a flexible aluminum substrate. The results indicate that it is feasible to produce a piezoelectric polymer multilayer structure on flexible substrate for harvesting mechanical energy applicable for many low-power electronics.

When Mothers and Fathers Work: How Employers Can Help.

ERIC Educational Resources Information Center

Magid, Renee Y.

1986-01-01

Discusses the plight of working parents. Offers suggestions for parent-tailored benefits such as flexible hours, benefits for permanent part-time employees, and family-oriented sick-leave policies. (JOW)

Financing to meet community needs: a guide for small hospitals.

PubMed

Wilson, Bill

2009-03-01

To succeed in the current financial markets, small hospitals need flexible project and financing plans. Many small local banks today can offer small hospitals financing solutions on par with what was previously offered only by the country's strongest investment-grade rated banks. Federal assistance through programs such as HUD's Section 242 mortgage insurance program is also a viable option for small hospitals.

Designing for flexible interaction between humans and automation: delegation interfaces for supervisory control.

PubMed

Miller, Christopher A; Parasuraman, Raja

2007-02-01

To develop a method enabling human-like, flexible supervisory control via delegation to automation. Real-time supervisory relationships with automation are rarely as flexible as human task delegation to other humans. Flexibility in human-adaptable automation can provide important benefits, including improved situation awareness, more accurate automation usage, more balanced mental workload, increased user acceptance, and improved overall performance. We review problems with static and adaptive (as opposed to "adaptable") automation; contrast these approaches with human-human task delegation, which can mitigate many of the problems; and revise the concept of a "level of automation" as a pattern of task-based roles and authorizations. We argue that delegation requires a shared hierarchical task model between supervisor and subordinates, used to delegate tasks at various levels, and offer instruction on performing them. A prototype implementation called Playbook is described. On the basis of these analyses, we propose methods for supporting human-machine delegation interactions that parallel human-human delegation in important respects. We develop an architecture for machine-based delegation systems based on the metaphor of a sports team's "playbook." Finally, we describe a prototype implementation of this architecture, with an accompanying user interface and usage scenario, for mission planning for uninhabited air vehicles. Delegation offers a viable method for flexible, multilevel human-automation interaction to enhance system performance while maintaining user workload at a manageable level. Most applications of adaptive automation (aviation, air traffic control, robotics, process control, etc.) are potential avenues for the adaptable, delegation approach we advocate. We present an extended example for uninhabited air vehicle mission planning.

A novel large thrust-weight ratio V-shaped linear ultrasonic motor with a flexible joint.

PubMed

Li, Xiaoniu; Yao, Zhiyuan; Yang, Mojian

2017-06-01

A novel large thrust-weight ratio V-shaped linear ultrasonic motor with a flexible joint is proposed in this paper. The motor is comprised of a V-shaped transducer, a slider, a clamp, and a base. The V-shaped transducer consists of two piezoelectric beams connected through a flexible joint to form an appropriate coupling angle. The V-shaped motor is operated in the coupled longitudinal-bending mode. Longitudinal and bending movements are transferred by the flexible joint between the two beams. Compared with the coupled longitudinal-bending mode of the single piezoelectric beam or the symmetrical and asymmetrical modes of the previous V-shaped transducer, the coupled longitudinal-bending mode of the V-shaped transducer with a flexible joint provides higher vibration efficiency and more convenient mode conformance adjustment. A finite element model of the V-shaped transducer is created to numerically study the influence of geometrical parameters and to determine the final geometrical parameters. In this paper, three prototypes were then fabricated and experimentally investigated. The modal test results match well with the finite element analysis. The motor mechanical output characteristics of three different coupling angles θ indicate that V-90 (θ = 90°) is the optimal angle. The mechanical output experiments conducted using the V-90 prototype (Size: 59.4 mm × 30.7 mm × 4 mm) demonstrate that the maximum unloaded speed is 1.2 m/s under a voltage of 350 Vpp, and the maximum output force is 15 N under a voltage of 300 Vpp. The proposed novel V-shaped linear ultrasonic motor has a compact size and a simple structure with a large thrust-weight ratio (0.75 N/g) and high speed.

Improve the material absorption of light and enhance the laser tube bending process utilizing laser softening heat treatment

NASA Astrophysics Data System (ADS)

Imhan, Khalil Ibraheem; Baharudin, B. T. H. T.; Zakaria, Azmi; Ismail, Mohd Idris Shah B.; Alsabti, Naseer Mahdi Hadi; Ahmad, Ahmad Kamal

2018-02-01

Laser forming is a flexible control process that has a wide spectrum of applications; particularly, laser tube bending. It offers the perfect solution for many industrial fields, such as aerospace, engines, heat exchangers, and air conditioners. A high power pulsed Nd-YAG laser with a maximum average power of 300 W emitting at 1064 nm and fiber-coupled is used to irradiate stainless steel 304 (SS304) tubes of 12.7 mm diameter, 0.6 mm thickness and 70 mm length. Moreover, a motorized rotation stage with a computer controller is employed to hold and rotate the tube. In this paper, an experimental investigation is carried out to improve the laser tube bending process by enhancing the absorption coefficient of the material and the mechanical formability using laser softening heat treatment. The material surface is coated with an oxidization layer; hence, the material absorption of laser light is increased and the temperature rapidly rises. The processing speed is enhanced and the output bending angle is increased to 1.9° with an increment of 70% after the laser softening heat treatment.

TRANSPOSABLE REGULARIZED COVARIANCE MODELS WITH AN APPLICATION TO MISSING DATA IMPUTATION

PubMed Central

Allen, Genevera I.; Tibshirani, Robert

2015-01-01

Missing data estimation is an important challenge with high-dimensional data arranged in the form of a matrix. Typically this data matrix is transposable, meaning that either the rows, columns or both can be treated as features. To model transposable data, we present a modification of the matrix-variate normal, the mean-restricted matrix-variate normal, in which the rows and columns each have a separate mean vector and covariance matrix. By placing additive penalties on the inverse covariance matrices of the rows and columns, these so called transposable regularized covariance models allow for maximum likelihood estimation of the mean and non-singular covariance matrices. Using these models, we formulate EM-type algorithms for missing data imputation in both the multivariate and transposable frameworks. We present theoretical results exploiting the structure of our transposable models that allow these models and imputation methods to be applied to high-dimensional data. Simulations and results on microarray data and the Netflix data show that these imputation techniques often outperform existing methods and offer a greater degree of flexibility. PMID:26877823

TRANSPOSABLE REGULARIZED COVARIANCE MODELS WITH AN APPLICATION TO MISSING DATA IMPUTATION.

PubMed

Allen, Genevera I; Tibshirani, Robert

2010-06-01

Missing data estimation is an important challenge with high-dimensional data arranged in the form of a matrix. Typically this data matrix is transposable , meaning that either the rows, columns or both can be treated as features. To model transposable data, we present a modification of the matrix-variate normal, the mean-restricted matrix-variate normal , in which the rows and columns each have a separate mean vector and covariance matrix. By placing additive penalties on the inverse covariance matrices of the rows and columns, these so called transposable regularized covariance models allow for maximum likelihood estimation of the mean and non-singular covariance matrices. Using these models, we formulate EM-type algorithms for missing data imputation in both the multivariate and transposable frameworks. We present theoretical results exploiting the structure of our transposable models that allow these models and imputation methods to be applied to high-dimensional data. Simulations and results on microarray data and the Netflix data show that these imputation techniques often outperform existing methods and offer a greater degree of flexibility.

Active weld control

NASA Technical Reports Server (NTRS)

Powell, Bradley W.; Burroughs, Ivan A.

1994-01-01

Through the two phases of this contract, sensors for welding applications and parameter extraction algorithms have been developed. These sensors form the foundation of a weld control system which can provide action weld control through the monitoring of the weld pool and keyhole in a VPPA welding process. Systems of this type offer the potential of quality enhancement and cost reduction (minimization of rework on faulty welds) for high-integrity welding applications. Sensors for preweld and postweld inspection, weld pool monitoring, keyhole/weld wire entry monitoring, and seam tracking were developed. Algorithms for signal extraction were also developed and analyzed to determine their application to an adaptive weld control system. The following sections discuss findings for each of the three sensors developed under this contract: (1) weld profiling sensor; (2) weld pool sensor; and (3) stereo seam tracker/keyhole imaging sensor. Hardened versions of these sensors were designed and built under this contract. A control system, described later, was developed on a multiprocessing/multitasking operating system for maximum power and flexibility. Documentation for sensor mechanical and electrical design is also included as appendices in this report.

sideSPIM - selective plane illumination based on a conventional inverted microscope.

PubMed

Hedde, Per Niklas; Malacrida, Leonel; Ahrar, Siavash; Siryaporn, Albert; Gratton, Enrico

2017-09-01

Previously described selective plane illumination microscopy techniques typically offset ease of use and sample handling for maximum imaging performance or vice versa . Also, to reduce cost and complexity while maximizing flexibility, it is highly desirable to implement light sheet microscopy such that it can be added to a standard research microscope instead of setting up a dedicated system. We devised a new approach termed sideSPIM that provides uncompromised imaging performance and easy sample handling while, at the same time, offering new applications of plane illumination towards fluidics and high throughput 3D imaging of multiple specimen. Based on an inverted epifluorescence microscope, all of the previous functionality is maintained and modifications to the existing system are kept to a minimum. At the same time, our implementation is able to take full advantage of the speed of the employed sCMOS camera and piezo stage to record data at rates of up to 5 stacks/s. Additionally, sample handling is compatible with established methods and switching magnification to change the field of view from single cells to whole organisms does not require labor intensive adjustments of the system.

The New Interventional Radiology Pathways: Options for Implementation.

PubMed

Recht, Michael; McKinney, J Mark; Alleman, Anthony M; Lowe, Lisa H; Spies, James B

2016-07-01

The new interventional radiology (IR) pathways have generated much discussion with articles and editorials pointing out perceived advantages and disadvantages compared to the current pathways. To briefly review, under the new system, there are three pathways to enter IR: the integrated (INT) IR residency, the independent (IND) IR residency, and the early specialization in interventional radiology (ESIR) program. The pathways have been designed to provide maximum flexibility to programs for implementation and to radiology residents for planning their subspecialty training. As a result, there are many potential permutations for these training programs, and understanding the variety of options can be a challenge at first. We offer three potential solutions, based on the different circumstances or requirements a department might face. The first two solutions involve integrated programs created through newly funded and converted diagnostic radiology slots, respectively. The third involves establishing ESIR and IND programs only. Hopefully, the examples provided will be useful for those currently planning for the future of their IR training programs. Copyright © 2016 The Association of University Radiologists. Published by Elsevier Inc. All rights reserved.

Endoscopes and robots for tight surgical spaces: use of precurved elastic elements to enhance curvature

NASA Astrophysics Data System (ADS)

Remirez, Andria A.; Webster, Robert J.

2016-03-01

Many applications in medicine require flexible surgical manipulators and endoscopes capable of reaching tight curvatures. The maximum curvature these devices can achieve is often restricted either by a strain limit, or by a maximum actuation force that the device's components can tolerate without risking mechanical failure. In this paper we propose the use of precurvature to "bias" the workspace of the device in one direction. Combined with axial shaft rotation, biasing increases the size of the device's workspace, enabling it to reach tighter curvatures than a comparable device without biasing can achieve, while still being able to fully straighten. To illustrate this effect, we describe several example prototype devices which use flexible nitinol strips that can be pushed and pulled to generate bending. We provide a statics model that relates the manipulator curvature to actuation force, and validate it experimentally.

Collaborations | FNLCR Staging

Cancer.gov

The Frederick National Lab has a range of contractual agreement options available which offer flexibility to facilitate the formation of partnerships. The appropriate business mechanism is considered based on the scope and objectives of the partnersh

The Nature and Necessity of Operational Flexibility in the Emergency Department

PubMed Central

Ferrand, Yann B.; Laker, Lauren F.; Froehle, Craig M.; Vogus, Timothy J.; Dittus, Robert S.; Kripalani, Sunil; Pines, Jesse M.

2014-01-01

Hospital-based emergency departments (ED), given their high cost and major role in allocating care resources,are at the center of the debate regarding how to maximize value in delivering healthcare in the United States. In order to operate effectively and create value, EDs must be flexible: the ability to rapidly adapt to the highly variable needs of patients. The concept of flexibility has not been well described in the ED literature. We introduce the concept,outline its potential benefits, and provide some illustrative examples to facilitate incorporating flexibility into ED management. We draw upon operations research and organizational theory to identify and describe five forms of flexibility: physical, human resource, volume, behavioral, and conceptual. Each form of flexibility may be individually or in combination with others useful in improving ED performance and enhancing value. We also offer suggestions for measuring operational flexibility in the ED. A better understanding of operational flexibility and its application to the ED may help us move away from reactive approaches of managing variable demand to a more systematic approach. We also address the tension between cost and flexibility and outline how “partial flexibility” may potentially help resolve some challenges. Applying concepts of flexibility from other disciplines may help clinicians and administrators think differently about their workflow and provide new insights into managing issues of cost, flow, and quality in the ED. PMID:25233811

Soft and wrinkled carbon membranes derived from petals for flexible supercapacitors

PubMed Central

Yu, Xiuxiu; Wang, Ying; Li, Li; Li, Hongbian; Shang, Yuanyuan

2017-01-01

Biomass materials are promising precursors for the production of carbonaceous materials due to their abundance, low cost and renewability. Here, a freestanding wrinkled carbon membrane (WCM) electrode material for flexible supercapacitors (SCs) was obtained from flower petal. The carbon membrane was fabricated by a simple thermal pyrolysis process and further activated by heating the sample in air. As a binder and current collector-free electrode, the activated wrinkled carbon membrane (AWCM) exhibited a high specific capacitance of 332.7 F/g and excellent cycling performance with 92.3% capacitance retention over 10000 cycles. Moreover, a flexible all-solid supercapacitor with AWCM electrode was fabricated and showed a maximum specific capacitance of 154 F/g and great bending stability. The development of this flower petal based carbon membrane provides a promising cost-effective and environmental benign electrode material for flexible energy storage. PMID:28361914

Gigahertz flexible graphene transistors for microwave integrated circuits.

PubMed

Yeh, Chao-Hui; Lain, Yi-Wei; Chiu, Yu-Chiao; Liao, Chen-Hung; Moyano, David Ricardo; Hsu, Shawn S H; Chiu, Po-Wen

2014-08-26

Flexible integrated circuits with complex functionalities are the missing link for the active development of wearable electronic devices. Here, we report a scalable approach to fabricate self-aligned graphene microwave transistors for the implementation of flexible low-noise amplifiers and frequency mixers, two fundamental building blocks of a wireless communication receiver. A devised AlOx T-gate structure is used to achieve an appreciable increase of device transconductance and a commensurate reduction of the associated parasitic resistance, thus yielding a remarkable extrinsic cutoff frequency of 32 GHz and a maximum oscillation frequency of 20 GHz; in both cases the operation frequency is an order of magnitude higher than previously reported. The two frequencies work at 22 and 13 GHz even when subjected to a strain of 2.5%. The gigahertz microwave integrated circuits demonstrated here pave the way for applications which require high flexibility and radio frequency operations.

Women's Career Development Patterns.

ERIC Educational Resources Information Center

Schreiber, Pamela J.

1998-01-01

Women's career development is characterized by balance of work and family, career interruptions, and diverse career paths. Alternative work arrangements such as flexible schedules, telecommuting, and entrepreneurial opportunities may offer women more options for work. (SK)

Pultruded composites using soy-based polyurethane resin.

DOT National Transportation Integrated Search

2008-07-01

Fiber Reinforced Polymer (FRP) composites offer inherent advantages over traditional materials with regard to high strength-to-weight ratio, design flexibility, corrosion resistance, low maintenance, and extended service life. FRP materials can be us...

Career Counseling for the Sandwich Generation.

ERIC Educational Resources Information Center

Byrd, Virginia; Grant-Vallone, Elisa; Hamill, Sharon B.

2001-01-01

Employers and counselors can help workers cope with multiple family caregiving responsibilities by offering flexible work options, reframing the meaning of career progress, addressing life role changes, and assessing and developing caregiver skills. (SK)

[Promising Future in General Internal Medicine for the Next Generation of Physicians].

PubMed

Allenbach, Victoria Perpinias; Rozsnyai, Zsofia; Streit, Sven

2018-06-01

Promising Future in General Internal Medicine for the Next Generation of Physicians Abstract. We are facing a lack of specialists in general internal medicine in general practitioners' practices as well as in hospitals, while at the same time the population ages and usually displays several chronic diseases (multimorbidity). Thanks to more university places, an improved job description for general internal medicine and new further education offers (curricula), interest in general internal medicine increased again, as surveys of students indicate. The young generation of family doctors and generalists in hospitals wishes flexible working conditions in order to reconcile work, family and spare time in the best possible way. Working atmosphere and colleagues have a high priority. These wishes must now be incorporated into attractive further training with flexible curricula and mentoring offers so that young talents can successfully be promoted.

Ureteric bupivicaine infusion for loin pain haematuria syndrome.

PubMed

Ahmed, M; Acher, P; Deane, A M

2010-03-01

Loin pain haematuria syndrome is a common problem with complications including opiate dependence. Morbidity treatments include intra-ureteric capsaicin infusion, nephrectomy, autotransplantation and nephrolysis. We explored the use of flexible cystoscopic infusion of intra-ureteric bupivicaine. Patients presenting with chronic loin pain underwent urological and nephrological evaluation. Bupivicaine (0.5%, 20 ml) was infused via an intra-ureteric catheter under flexible cystoscopic guidance. Repeat infusions were offered if indicated. Sixteen of 17 patients with 1-year follow-up responded and were satisfied. Twelve of these required repeat infusions (mean, 2.9 infusions). The procedures were well tolerated by all patients without adverse effects. Intra-ureteric bupivicaine infusion has a place in the management of patients with chronic renal pain. It offers a minimally invasive alternative to other treatments. This procedure warrants further investigation within a randomised, controlled trial setting.

SCC500: next-generation infrared imaging camera core products with highly flexible architecture for unique camera designs

NASA Astrophysics Data System (ADS)

Rumbaugh, Roy N.; Grealish, Kevin; Kacir, Tom; Arsenault, Barry; Murphy, Robert H.; Miller, Scott

2003-09-01

A new 4th generation MicroIR architecture is introduced as the latest in the highly successful Standard Camera Core (SCC) series by BAE SYSTEMS to offer an infrared imaging engine with greatly reduced size, weight, power, and cost. The advanced SCC500 architecture provides great flexibility in configuration to include multiple resolutions, an industry standard Real Time Operating System (RTOS) for customer specific software application plug-ins, and a highly modular construction for unique physical and interface options. These microbolometer based camera cores offer outstanding and reliable performance over an extended operating temperature range to meet the demanding requirements of real-world environments. A highly integrated lens and shutter is included in the new SCC500 product enabling easy, drop-in camera designs for quick time-to-market product introductions.

Evaluation of different operating strategies to integrate storage in a linear Fresnel ORC power plant

NASA Astrophysics Data System (ADS)

Zoschke, Theda; Seubert, Bernhard; Fluri, Thomas

2017-06-01

An existing linear Fresnel power plant with ORC process located in Ben Guerir, Morocco, is retrofitted with a thermal energy storage system and additional collector loops. Two different plant configurations are investigated in this paper. In the first configuration two separate solar fields are built and only the minor one can charge the storage. In the second configuration, there is only one large solar field which offers more flexibility. Two different control strategies are assessed by comparing simulation results. It shows that the simulations of the systems with two solar fields results in higher energy yields throughout the year, but the power production of the system with one solar field is much more flexible and demand oriented. Also it offers great potential for improvement when it comes to weather forecasting.

Coherent photonic beamformer for a Ka-band phased array antenna receiver implemented in silicon photonic integrated circuit

NASA Astrophysics Data System (ADS)

Duarte, V. C.; Peczek, A.; Drummond, M. V.; Nogueira, R. N.; Winzer, G.; Petousi, D.; Zimmermann, L.

2017-09-01

The generation of satellite communications with flexible and efficient transmission of radio signals requires a large number of low interfering beams and a maximum exploitation of the available frequency spectrum.

Transmission Challenges and Best Practices for Cost-Effective Renewable Energy Delivery across State and Provincial Boundaries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Shengru; Hurlbut, David J.; Bird, Lori A.

A strategically planned transmission network is an important source of flexibility for the integration of large-scale renewable energy (RE). Such a network can offer access to a broad geographic diversity of resources, which can reduce flexibility needs and facilitate sharing between neighboring balancing areas. This report builds on two previous NREL technical reports - Advancing System Flexibility for High Penetration Renewable Integration (Milligan et al. 2015) and 'Renewables-Friendly' Grid Development Strategies (Hurlbut et al. 2015) - which discuss various flexibility options and provide an overview of U.S. market models and grid planning. This report focuses on addressing issues with cross-regional/provincialmore » transmission in China with the aim of integrating renewable resources that are concentrated in remote areas and require inter-regional/provincial power exchange.« less

Living in a Flexible Space

NASA Astrophysics Data System (ADS)

Canepa, Simona

2017-10-01

How long does a space or an object have to last? If in the past an object or a building manufacturing was designed to last as much as possible, nowadays it is designed to have a life related to the time in which it will be used. Flexibility is what characterizes a space, it’s the ability to be variable and adaptable to changes in the lives of users or in relation to the use which these will make over time. The evolution of the labour market, the difficulty of inserting within it and the need to push more and more frequent move today in the trial of living space models increasingly flexible: people, especially young people, are forced to move on territory outlining a new condition to which the flexible nomadic dwellings offer an adequate response, ensuring high functional performance in confined spaces.

Direct and Dry Deposited Single-Walled Carbon Nanotube Films Doped with MoO(x) as Electron-Blocking Transparent Electrodes for Flexible Organic Solar Cells.

PubMed

Jeon, Il; Cui, Kehang; Chiba, Takaaki; Anisimov, Anton; Nasibulin, Albert G; Kauppinen, Esko I; Maruyama, Shigeo; Matsuo, Yutaka

2015-07-01

Organic solar cells have been regarded as a promising electrical energy source. Transparent and conductive carbon nanotube film offers an alternative to commonly used ITO in photovoltaics with superior flexibility. This communication reports carbon nanotube-based indium-free organic solar cells and their flexible application. Direct and dry deposited carbon nanotube film doped with MoO(x) functions as an electron-blocking transparent electrode, and its performance is enhanced further by overcoating with PSS. The single-walled carbon nanotube organic solar cell in this work shows a power conversion efficiency of 6.04%. This value is 83% of the leading ITO-based device performance (7.48%). Flexible application shows 3.91% efficiency and is capable of withstanding a severe cyclic flex test.

Strengthening Building Retrofit Markets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Templeton, Mary; Jackson, Robert

2014-04-15

The Business Energy Financing (BEF) program offered commercial businesses in Michigan affordable financing options and other incentives designed to support energy efficiency improvements. We worked through partnerships with Michigan utilities, lenders, building contractors, trade associations, and other community organizations to offer competitive interest rates and flexible financing terms to support energy efficiency projects that otherwise would not have happened. The BEF program targeted the retail food market, including restaurants, grocery stores, convenience stores, and wholesale food vendors, with the goal of achieving energy efficiency retrofits for 2 percent of the target market. We offered low interest rates, flexible payments, easymore » applications and approval processes, and access to other incentives and rebates. Through these efforts, we sought to help customers strive for energy savings retrofits that would save 20 percent or more on their energy use. This program helped Michigan businesses reduce costs by financing energy efficient lighting, heating and cooling systems, insulation, refrigeration, equipment upgrades, and more. Businesses completed the upgrades with the help of our authorized contractors, and, through our lending partners, we provided affordable financing options.« less

Design and Fabrication of Human Skin by Three-Dimensional Bioprinting

PubMed Central

Lee, Vivian; Singh, Gurtej; Trasatti, John P.; Bjornsson, Chris; Xu, Xiawei; Tran, Thanh Nga; Yoo, Seung-Schik

2014-01-01

Three-dimensional (3D) bioprinting, a flexible automated on-demand platform for the free-form fabrication of complex living architectures, is a novel approach for the design and engineering of human organs and tissues. Here, we demonstrate the potential of 3D bioprinting for tissue engineering using human skin as a prototypical example. Keratinocytes and fibroblasts were used as constituent cells to represent the epidermis and dermis, and collagen was used to represent the dermal matrix of the skin. Preliminary studies were conducted to optimize printing parameters for maximum cell viability as well as for the optimization of cell densities in the epidermis and dermis to mimic physiologically relevant attributes of human skin. Printed 3D constructs were cultured in submerged media conditions followed by exposure of the epidermal layer to the air–liquid interface to promote maturation and stratification. Histology and immunofluorescence characterization demonstrated that 3D printed skin tissue was morphologically and biologically representative of in vivo human skin tissue. In comparison with traditional methods for skin engineering, 3D bioprinting offers several advantages in terms of shape- and form retention, flexibility, reproducibility, and high culture throughput. It has a broad range of applications in transdermal and topical formulation discovery, dermal toxicity studies, and in designing autologous grafts for wound healing. The proof-of-concept studies presented here can be further extended for enhancing the complexity of the skin model via the incorporation of secondary and adnexal structures or the inclusion of diseased cells to serve as a model for studying the pathophysiology of skin diseases. PMID:24188635

Design and fabrication of human skin by three-dimensional bioprinting.

PubMed

Lee, Vivian; Singh, Gurtej; Trasatti, John P; Bjornsson, Chris; Xu, Xiawei; Tran, Thanh Nga; Yoo, Seung-Schik; Dai, Guohao; Karande, Pankaj

2014-06-01

Three-dimensional (3D) bioprinting, a flexible automated on-demand platform for the free-form fabrication of complex living architectures, is a novel approach for the design and engineering of human organs and tissues. Here, we demonstrate the potential of 3D bioprinting for tissue engineering using human skin as a prototypical example. Keratinocytes and fibroblasts were used as constituent cells to represent the epidermis and dermis, and collagen was used to represent the dermal matrix of the skin. Preliminary studies were conducted to optimize printing parameters for maximum cell viability as well as for the optimization of cell densities in the epidermis and dermis to mimic physiologically relevant attributes of human skin. Printed 3D constructs were cultured in submerged media conditions followed by exposure of the epidermal layer to the air-liquid interface to promote maturation and stratification. Histology and immunofluorescence characterization demonstrated that 3D printed skin tissue was morphologically and biologically representative of in vivo human skin tissue. In comparison with traditional methods for skin engineering, 3D bioprinting offers several advantages in terms of shape- and form retention, flexibility, reproducibility, and high culture throughput. It has a broad range of applications in transdermal and topical formulation discovery, dermal toxicity studies, and in designing autologous grafts for wound healing. The proof-of-concept studies presented here can be further extended for enhancing the complexity of the skin model via the incorporation of secondary and adnexal structures or the inclusion of diseased cells to serve as a model for studying the pathophysiology of skin diseases.

The nature and necessity of operational flexibility in the emergency department.

PubMed

Ward, Michael J; Ferrand, Yann B; Laker, Lauren F; Froehle, Craig M; Vogus, Timothy J; Dittus, Robert S; Kripalani, Sunil; Pines, Jesse M

2015-02-01

Hospital-based emergency departments (EDs), given their high cost and major role in allocating care resources, are at the center of the debate about how to maximize value in delivering health care in the United States. To operate effectively and create value, EDs must be flexible, having the ability to rapidly adapt to the highly variable needs of patients. The concept of flexibility has not been well described in the ED literature. We introduce the concept, outline its potential benefits, and provide some illustrative examples to facilitate incorporating flexibility into ED management. We draw on operations research and organizational theory to identify and describe 5 forms of flexibility: physical, human resource, volume, behavioral, and conceptual. Each form of flexibility may be useful individually or in combination with other forms in improving ED performance and enhancing value. We also offer suggestions for measuring operational flexibility in the ED. A better understanding of operational flexibility and its application to the ED may help us move away from reactive approaches of managing variable demand to a more systematic approach. We also address the tension between cost and flexibility and outline how "partial flexibility" may help resolve some challenges. Applying concepts of flexibility from other disciplines may help clinicians and administrators think differently about their workflow and provide new insights into managing issues of cost, flow, and quality in the ED. Copyright © 2014 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

Using high thermal stability flexible thin film thermoelectric generator at moderate temperature

NASA Astrophysics Data System (ADS)

Zheng, Zhuang-Hao; Luo, Jing-Ting; Chen, Tian-Bao; Zhang, Xiang-Hua; Liang, Guang-Xing; Fan, Ping

2018-04-01

Flexible thin film thermoelectric devices are extensively used in the microscale industry for powering wearable electronics. In this study, comprehensive optimization was conducted in materials and connection design for fabricating a high thermal stability flexible thin film thermoelectric generator. First, the thin films in the generator, including the electrodes, were prepared by magnetron sputtering deposition. The "NiCu-Cu-NiCu" multilayer electrode structure was applied to ensure the thermal stability of the device used at moderate temperature in an air atmosphere. A design with metal layer bonding and series accordant connection was then employed. The maximum efficiency of a single PN thermocouple generator is >11%, and the output power loss of the generator is <10% after integration.

12-GHz thin-film transistors on transferrable silicon nanomembranes for high-performance flexible electronics.

PubMed

Sun, Lei; Qin, Guoxuan; Seo, Jung-Hun; Celler, George K; Zhou, Weidong; Ma, Zhenqiang

2010-11-22

Multigigahertz flexible electronics are attractive and have broad applications. A gate-after-source/drain fabrication process using preselectively doped single-crystal silicon nanomembranes (SiNM) is an effective approach to realizing high device speed. However, further downscaling this approach has become difficult in lithography alignment. In this full paper, a local alignment scheme in combination with more accurate SiNM transfer measures for minimizing alignment errors is reported. By realizing 1 μm channel alignment for the SiNMs on a soft plastic substrate, thin-film transistors with a record speed of 12 GHz maximum oscillation frequency are demonstrated. These results indicate the great potential of properly processed SiNMs for high-performance flexible electronics.

Automatic outdoor monitoring system for photovoltaic panels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stefancich, Marco; Simpson, Lin; Chiesa, Matteo

Long-term acquisition of solar panel performance parameters, for panels operated at maximum power point in their real environment, is of critical importance in the photovoltaic research sector. However, few options exist for the characterization of non-standard panels such as concentrated photovoltaic systems, heavily soiled or shaded panels or those operating under non-standard spectral illumination; certainly, it is difficult to find such a measurement system that is flexible and affordable enough to be adopted by the smaller research institutes or universities. We present here an instrument aiming to fill this gap, autonomously tracking and maintaining any solar panel at maximum powermore » point while continuously monitoring its operational parameters and dissipating the produced energy without connection to the power grid. The instrument allows periodic acquisition of current-voltage curves to verify the employed maximum power point tracking approach. At the same time, with hardware schematics and software code being provided, it provides a flexible open development environment for the monitoring of non-standard generators like concentrator photovoltaic systems and to test novel power tracking approaches. The key issues, and the corresponding solutions, encountered in the design are analyzed in detail and the relevant schematics presented.« less

Automatic outdoor monitoring system for photovoltaic panels.

PubMed

Stefancich, Marco; Simpson, Lin; Chiesa, Matteo

2016-05-01

Long-term acquisition of solar panel performance parameters, for panels operated at maximum power point in their real environment, is of critical importance in the photovoltaic research sector. However, few options exist for the characterization of non-standard panels such as concentrated photovoltaic systems, heavily soiled or shaded panels or those operating under non-standard spectral illumination; certainly, it is difficult to find such a measurement system that is flexible and affordable enough to be adopted by the smaller research institutes or universities. We present here an instrument aiming to fill this gap, autonomously tracking and maintaining any solar panel at maximum power point while continuously monitoring its operational parameters and dissipating the produced energy without connection to the power grid. The instrument allows periodic acquisition of current-voltage curves to verify the employed maximum power point tracking approach. At the same time, with hardware schematics and software code being provided, it provides a flexible open development environment for the monitoring of non-standard generators like concentrator photovoltaic systems and to test novel power tracking approaches. The key issues, and the corresponding solutions, encountered in the design are analyzed in detail and the relevant schematics presented.

A low-frequency MEMS piezoelectric energy harvester with a rectangular hole based on bulk PZT film

NASA Astrophysics Data System (ADS)

Tian, Yingwei; Li, Guimiao; Yi, Zhiran; Liu, Jingquan; Yang, Bin

2018-06-01

This paper presents a high performance piezoelectric energy harvester (PEH) with a rectangular hole to work at low-frequency. This PEH used thinned bulk PZT film on flexible phosphor bronze, and its structure included piezoelectric layer, supporting layer and proof mass to reduce the resonant frequency of the device. Here, thinned bulk PZT thick film was used as piezoelectric layer due to its high piezoelectric coefficient. A Phosphor bronze was deployed as supporting layer because it had better flexibility compared to silicon and could work under high acceleration ambient with good durability. The maximum open-circuit voltage of the PEH was 15.7 V at low resonant frequency of 34.3 Hz when the input vibration acceleration was 1.5 g (g = 9.81 m/s2). Moreover, the maximum output power, the output power density and the actually current at the same acceleration were 216.66 μW, 1713.58 μW/cm3 and 170 μA, respectively, when the optimal matched resistance of 60 kΩ was connected. The fabricated PEH scavenged the vibration energy of the vacuum compression pump and generated the maximum output voltage of 1.19 V.

Support for Training Effectiveness Assessment and Data Interoperability (STEADI)

DTIC Science & Technology

2017-05-02

will guide future efforts of the services to broadly incorporate IPA concepts across the continuum of training . Throughout the course of this effort...data access issues for marksmanship training systems. In comparison to updating Pipeline, the registry also offered more flexibility, eased future...development would be required, SP2 offers a good starting point to accelerate development efforts and lower costs to ARL. Acting as the central glue

Robust remote-pumping sodium laser for advanced LIDAR and guide star applications

NASA Astrophysics Data System (ADS)

Ernstberger, Bernhard; Enderlein, Martin; Friedenauer, Axel; Schwerdt, Robin; Wei, Daoping; Karpov, Vladimir; Leisching, Patrick; Clements, Wallace R. L.; Kaenders, Wilhelm G.

2015-10-01

The performance of large ground-based optical telescopes is limited due to wavefront distortions induced by atmospheric turbulence. Adaptive optics systems using natural guide stars with sufficient brightness provide a practical way for correcting the wavefront errors by means of deformable mirrors. Unfortunately, the sky coverage of bright stars is poor and therefore the concept of laser guide stars was invented, creating an artificial star by exciting resonance fluorescence from the mesospheric sodium layer about 90 km above the earth's surface. Until now, mainly dye lasers or sumfrequency mixing of solid state lasers were used to generate laser guide stars. However, these kinds of lasers require a stationary laser clean room for operation and are extremely demanding in maintenance. Under a development contract with the European Southern Observatory (ESO) and W. M. Keck Observatory (WMKO), TOPTICA Photonics AG and its partner MPB Communications have finalized the development of a next-generation sodium guide star laser system which is available now as a commercial off-the-shelf product. The laser is based on a narrow-band diode laser, Raman fiber amplifier (RFA) technology and resonant second-harmonic generation (SHG), thus highly reliable and simple to operate and maintain. It emits > 22 W of narrow-linewidth (≈ 5 MHz) continuous-wave radiation at sodium resonance and includes a re-pumping scheme for boosting sodium return flux. Due to the SHG resonator acting as spatial mode filter and polarizer, the output is diffraction-limited with RMS wavefront error < λ/25. Apart from this unique optical design, a major effort has been dedicated to integrating all optical components into a ruggedized system, providing a maximum of convenience and reliability for telescope operators. The new remote-pumping architecture allows for a large spatial separation between the main part of the laser and the compact laser head. Together with a cooling-water flow of less than 5 l/min and an overall power consumption of < 700 W, the system offers a maximum of flexibility with minimal infrastructure demands on site. Each system is built in a modular way, based on the concept of line-replaceable units (LRU). A comprehensive system software, as well as an intuitive service GUI, allow for remote control and error tracking down to at least the LRU level. In case of a failure, any LRU can be easily replaced. With these fiber-based guide star lasers, TOPTICA for the first time offers a fully engineered, off-the-shelf guide star laser system for groundbased optical telescopes providing convenient, turn-key operation in remote and harsh locations. Reliability and flexibility will be beneficial in particular for advanced satellite and space debris tracking as well as LIDAR applications.

Additive manufactured push-fit implant fixation with screw-strength pull out.

PubMed

van Arkel, Richard J; Ghouse, Shaaz; Milner, Piers E; Jeffers, Jonathan R T

2017-10-11

Additive manufacturing offers exciting new possibilities for improving long-term metallic implant fixation in bone through enabling open porous structures for bony ingrowth. The aim of this research was to investigate how the technology could also improve initial fixation, a precursor to successful long-term fixation. A new barbed fixation mechanism, relying on flexible struts was proposed and manufactured as a push-fit peg. The technology was optimized using a synthetic bone model and compared with conventional press-fit peg controls tested over a range of interference fits. Optimum designs, achieving maximum pull-out force, were subsequently tested in a cadaveric femoral condyle model. The barbed fixation surface provided more than double the pull-out force for less than a third of the insertion force compared to the best performing conventional press-fit peg (p < 0.001). Indeed, it provided screw-strength pull out from a push-fit device (1,124 ± 146 N). This step change in implant fixation potential offers new capabilities for low profile, minimally invasive implant design, while providing new options to simplify surgery, allowing for one-piece push-fit components with high levels of initial stability. © 2017 The Authors. Journal of Orthopaedic Research Published by WileyPeriodicals, Inc. on behalf of the Orthopaedic Research Society. J Orthop Res 9999:1-11, 2017. © 2017 The Authors. Journal of Orthopaedic Research Published by WileyPeriodicals, Inc. on behalf of the Orthopaedic Research Society.

Flexible Blades for Wind Turbines

NASA Astrophysics Data System (ADS)

Collins, Madeline Carlisle; Macphee, David; Harris, Caleb

2016-11-01

Previous research has shown that windmills with flexible blades are more efficient than those with rigid blades. Flexibility offers passive pitch control, preferable to active pitch control which is costly and requires maintenance. Flexible blades morph such that the blade more closely resembles its design point at part load and over load. The lift-to-drag ratios on individual blades was investigated. A mold was designed and machined from an acrylic slab for the casting of blades with a NACA 0012 cross section. A flexible blade was cast from silicone and a rigid blade was cast from polyurethane. Each of these blades was tested in a wind tunnel, cantilever mounted, spanning the whole test section. The angle of attack was varied by rotating the mount. All tests were performed at the same wind speed. A load cell within the mount measured forces on the blade, from which the lift and drag forces were calculated. The stall point for the flexible blade occurred later than for the rigid blade, which agrees with previous research. Lift-to-drag ratios were larger for the flexible blade at all angles of attack tested. Flexible blades seem to be a viable option for passive pitch control. Future research will include different airfoil cross sections, wind speeds, and blade materials. Funding from NSF REU site Grant EEC 1358991 is greatly appreciated.

High-Level Data-Abstraction System

NASA Technical Reports Server (NTRS)

Fishwick, P. A.

1986-01-01

Communication with data-base processor flexible and efficient. High Level Data Abstraction (HILDA) system is three-layer system supporting data-abstraction features of Intel data-base processor (DBP). Purpose of HILDA establishment of flexible method of efficiently communicating with DBP. Power of HILDA lies in its extensibility with regard to syntax and semantic changes. HILDA's high-level query language readily modified. Offers powerful potential to computer sites where DBP attached to DEC VAX-series computer. HILDA system written in Pascal and FORTRAN 77 for interactive execution.

Shared service alternatives offer flexibility and tax benefits.

PubMed

Danehy, L J; Scutt, R C; Stonehill, E

1985-05-01

Because the performance of shared service and tax-exempt status under Section 501(c)(3) of the Internal Revenue Code can be incompatible, hospitals planning to provide services to each other or to other organizations on a fee-for-service basis may wish to do so through a separate corporate entity. Using either a Section 501(e) shared service organization, a Sub-chapter T cooperative, or a taxable business corporation, a compromise can be reached between operational flexibility and tax benefits.

Oxygen-deficient hematite nanorods as high-performance and novel negative electrodes for flexible asymmetric supercapacitors.

PubMed

Lu, Xihong; Zeng, Yinxiang; Yu, Minghao; Zhai, Teng; Liang, Chaolun; Xie, Shilei; Balogun, Muhammad-Sadeeq; Tong, Yexiang

2014-05-21

Oxygen-deficient α-Fe2 O3 nanorods with outstanding capacitive performance are developed and demonstrated as novel negative electrodes for flexible asymmetric supercapacitors. The asymmetric-supercapacitor device based on the oxygen-deficient α-Fe2 O3 nanorod negative electrode and a MnO2 positive electrode achieves a maximum energy density of 0.41 mW·h/cm(3) ; it is also capable of charging a mobile phone and powering a light-emitting diode indicator. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Making Choices: Self-Directed Teams or Total Quality Management?

ERIC Educational Resources Information Center

Holpp, Lawrence

1992-01-01

Describes differences between total quality management and self-directed teams in terms of job design, decision making, flexibility, supervision, labor relations, quality, customers, and training. Offers suggestions for which method to choose when. (SK)

Line pilot perspectives on complexity of terminal instrument flight procedures

DOT National Transportation Integrated Search

2017-07-25

Instrument flight procedures (IFPs) based on RNAV and RNP offer safety enhancements along with new levels of flexibility to negotiate terrain, airspace, and environmental considerations. However, operational implementation of performance-based IFPs d...

Framework for Ecological Risk Assessment

EPA Pesticide Factsheets

This is the first step in a long-term effort to develop risk assessment guidelines for ecological effects. Its primary purpose is to offer a simple, flexible structure for conducting and evaluating ecological risk assessment within EPA.

Collaborations | Frederick National Laboratory for Cancer Research

Cancer.gov

The Frederick National Laboratory has a range of contractual agreement options available which offer flexibility to facilitate the formation of partnerships. The appropriate business mechanism is considered based on the scope and objectives of the pa

Shopping for Knowledge: An Alternative Environment for Learning.

ERIC Educational Resources Information Center

Joseph, Gillian

1996-01-01

Shopping malls are environments in which many adults find community. They are potentially ideal for adult learning, especially via the Internet, because they can offer pacing, flexible hours, and self-direction and interaction. (SK)

Flexible and Robust Thermoelectric Generators Based on All-Carbon Nanotube Yarn without Metal Electrodes.

PubMed

Choi, Jaeyoo; Jung, Yeonsu; Yang, Seung Jae; Oh, Jun Young; Oh, Jinwoo; Jo, Kiyoung; Son, Jeong Gon; Moon, Seung Eon; Park, Chong Rae; Kim, Heesuk

2017-08-22

As practical interest in flexible/or wearable power-conversion devices increases, the demand for high-performance alternatives to thermoelectric (TE) generators based on brittle inorganic materials is growing. Herein, we propose a flexible and ultralight TE generator (TEG) based on carbon nanotube yarn (CNTY) with excellent TE performance. The as-prepared CNTY shows a superior electrical conductivity of 3147 S/cm due to increased longitudinal carrier mobility derived from a highly aligned structure. Our TEG is innovative in that the CNTY acts as multifunctions in the same device. The CNTY is alternatively doped into n- and p-types using polyethylenimine and FeCl 3 , respectively. The highly conductive CNTY between the doped regions is used as electrodes to minimize the circuit resistance, thereby forming an all-carbon TEG without additional metal deposition. A flexible TEG based on 60 pairs of n- and p-doped CNTY shows the maximum power density of 10.85 and 697 μW/g at temperature differences of 5 and 40 K, respectively, which are the highest values among reported TEGs based on flexible materials. We believe that the strategy proposed here to improve the power density of flexible TEG by introducing highly aligned CNTY and designing a device without metal electrodes shows great potential for the flexible/or wearable power-conversion devices.

Dopamine and the Development of Executive Dysfunction in Autism Spectrum Disorders

PubMed Central

Kriete, Trenton; Noelle, David C.

2015-01-01

Persons with autism regularly exhibit executive dysfunction (ED), including problems with deliberate goal-directed behavior, planning, and flexible responding in changing environments. Indeed, this array of deficits is sufficiently prominent to have prompted a theory that executive dysfunction is at the heart of these disorders. A more detailed examination of these behaviors reveals, however, that some aspects of executive function remain developmentaly appropriate. In particular, while people with autism often have difficulty with tasks requiring cognitive flexibility, their fundamental cognitive control capabilities, such as those involved in inhibiting an inappropriate but relatively automatic response, show no significant impairment on many tasks. In this article, an existing computational model of the prefrontal cortex and its role in executive control is shown to explain this dichotomous pattern of behavior by positing abnormalities in the dopamine-based modulation of frontal systems in individuals with autism. This model offers excellent qualitative and quantitative fits to performance on standard tests of cognitive control and cognitive flexibility in this clinical population. By simulating the development of the prefrontal cortex, the computational model also offers a potential explanation for an observed lack of executive dysfunction early in life. PMID:25811610

Dopamine and the development of executive dysfunction in autism spectrum disorders.

PubMed

Kriete, Trenton; Noelle, David C

2015-01-01

Persons with autism regularly exhibit executive dysfunction (ED), including problems with deliberate goal-directed behavior, planning, and flexible responding in changing environments. Indeed, this array of deficits is sufficiently prominent to have prompted a theory that executive dysfunction is at the heart of these disorders. A more detailed examination of these behaviors reveals, however, that some aspects of executive function remain developmentaly appropriate. In particular, while people with autism often have difficulty with tasks requiring cognitive flexibility, their fundamental cognitive control capabilities, such as those involved in inhibiting an inappropriate but relatively automatic response, show no significant impairment on many tasks. In this article, an existing computational model of the prefrontal cortex and its role in executive control is shown to explain this dichotomous pattern of behavior by positing abnormalities in the dopamine-based modulation of frontal systems in individuals with autism. This model offers excellent qualitative and quantitative fits to performance on standard tests of cognitive control and cognitive flexibility in this clinical population. By simulating the development of the prefrontal cortex, the computational model also offers a potential explanation for an observed lack of executive dysfunction early in life.

77 FR 29537 - Community Facility Loans

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-18

... alternate contracting method projects must comply with the requirements for ``maximum open and free... of alternate construction contract methods (such as Design/Build and Construction Management) by the.... Further, these changes will give all applicants greater flexibility in developing projects. Therefore, a...

Agreement Between Face-to-Face and Free Software Video Analysis for Assessing Hamstring Flexibility in Adolescents.

PubMed

Moral-Muñoz, José A; Esteban-Moreno, Bernabé; Arroyo-Morales, Manuel; Cobo, Manuel J; Herrera-Viedma, Enrique

2015-09-01

The objective of this study was to determine the level of agreement between face-to-face hamstring flexibility measurements and free software video analysis in adolescents. Reduced hamstring flexibility is common in adolescents (75% of boys and 35% of girls aged 10). The length of the hamstring muscle has an important role in both the effectiveness and the efficiency of basic human movements, and reduced hamstring flexibility is related to various musculoskeletal conditions. There are various approaches to measuring hamstring flexibility with high reliability; the most commonly used approaches in the scientific literature are the sit-and-reach test, hip joint angle (HJA), and active knee extension. The assessment of hamstring flexibility using video analysis could help with adolescent flexibility follow-up. Fifty-four adolescents from a local school participated in a descriptive study of repeated measures using a crossover design. Active knee extension and HJA were measured with an inclinometer and were simultaneously recorded with a video camera. Each video was downloaded to a computer and subsequently analyzed using Kinovea 0.8.15, a free software application for movement analysis. All outcome measures showed reliability estimates with α > 0.90. The lowest reliability was obtained for HJA (α = 0.91). The preliminary findings support the use of a free software tool for assessing hamstring flexibility, offering health professionals a useful tool for adolescent flexibility follow-up.

Flexible plastic, paper and textile lab-on-a chip platforms for electrochemical biosensing.

PubMed

Economou, Anastasios; Kokkinos, Christos; Prodromidis, Mamas

2018-06-26

Flexible biosensors represent an increasingly important and rapidly developing field of research. Flexible materials offer several advantages as supports of biosensing platforms in terms of flexibility, weight, conformability, portability, cost, disposability and scope for integration. On the other hand, electrochemical detection is perfectly suited to flexible biosensing devices. The present paper reviews the field of integrated electrochemical bionsensors fabricated on flexible materials (plastic, paper and textiles) which are used as functional base substrates. The vast majority of electrochemical flexible lab-on-a-chip (LOC) biosensing devices are based on plastic supports in a single or layered configuration. Among these, wearable devices are perhaps the ones that most vividly demonstrate the utility of the concept of flexible biosensors while diagnostic cards represent the state-of-the art in terms of integration and functionality. Another important type of flexible biosensors utilize paper as a functional support material enabling the fabrication of low-cost and disposable paper-based devices operating on the lateral flow, drop-casting or folding (origami) principles. Finally, textile-based biosensors are beginning to emerge enabling real-time measurements in the working environment or in wound care applications. This review is timely due to the significant advances that have taken place over the last few years in the area of LOC biosensors and aims to direct the readers to emerging trends in this field.

Role of Pectoral Fin Flexibility in Robotic Fish Performance

NASA Astrophysics Data System (ADS)

Bazaz Behbahani, Sanaz; Tan, Xiaobo

2017-08-01

Pectoral fins play a vital role in the maneuvering and locomotion of fish, and they have become an important actuation mechanism for robotic fish. In this paper, we explore the effect of flexibility of robotic fish pectoral fins on the robot locomotion performance and mechanical efficiency. A dynamic model for the robotic fish is presented, where the flexible fin is modeled as multiple rigid elements connected via torsional springs and dampers. Blade element theory is used to capture the hydrodynamic force on the fin. The model is validated with experimental results obtained on a robotic fish prototype, equipped with 3D-printed fins of different flexibility. The model is then used to analyze the impacts of fin flexibility and power/recovery stroke speed ratio on the robot swimming speed and mechanical efficiency. It is found that, in general, flexible fins demonstrate advantages over rigid fins in speed and efficiency at relatively low fin-beat frequencies, while rigid fins outperform flexible fins at higher frequencies. For a given fin flexibility, the optimal frequency for speed performance differs from the optimal frequency for mechanical efficiency. In addition, for any given fin, there is an optimal power/recovery stroke speed ratio, typically in the range of 2-3, that maximizes the speed performance. Overall, the presented model offers a promising tool for fin flexibility and gait design, to achieve speed and efficiency objectives for robotic fish actuated with pectoral fins.

Layered-MnO₂ Nanosheet Grown on Nitrogen-Doped Graphene Template as a Composite Cathode for Flexible Solid-State Asymmetric Supercapacitor.

PubMed

Liu, Yongchuan; Miao, Xiaofei; Fang, Jianhui; Zhang, Xiangxin; Chen, Sujing; Li, Wei; Feng, Wendou; Chen, Yuanqiang; Wang, Wei; Zhang, Yining

2016-03-02

Flexible solid-state supercapacitors provide a promising energy-storage alternative for the rapidly growing flexible and wearable electronic industry. Further improving device energy density and developing a cheap flexible current collector are two major challenges in pushing the technology forward. In this work, we synthesize a nitrogen-doped graphene/MnO2 nanosheet (NGMn) composite by a simple hydrothermal method. Nitrogen-doped graphene acts as a template to induce the growth of layered δ-MnO2 and improves the electronic conductivity of the composite. The NGMn composite exhibits a large specific capacitance of about 305 F g(-1) at a scan rate of 5 mV s(-1). We also create a cheap and highly conductive flexible current collector using Scotch tape. Flexible solid-state asymmetric supercapacitors are fabricated with NGMn cathode, activated carbon anode, and PVA-LiCl gel electrolyte. The device can achieve a high operation voltage of 1.8 V and exhibits a maximum energy density of 3.5 mWh cm(-3) at a power density of 0.019 W cm(-3). Moreover, it retains >90% of its initial capacitance after 1500 cycles. Because of its flexibility, high energy density, and good cycle life, NGMn-based flexible solid state asymmetric supercapacitors have great potential for application in next-generation portable and wearable electronics.

Towards development of nanofibrous large strain flexible strain sensors with programmable shape memory properties

NASA Astrophysics Data System (ADS)

Khalili, N.; Asif, H.; Naguib, H. E.

2018-05-01

Electrospun polymeric fibers can be used as strain sensors due to their large surface to weight/volume ratio, high porosity and pore interconnectivity. Large strain flexible strain sensors are used in numerous applications including rehabilitation, health monitoring, and sports performance monitoring where large strain detection should be accommodated by the sensor. This has boosted the demand for a stretchable, flexible and highly sensitive sensor able to detect a wide range of mechanically induced deformations. Herein, a physically cross-linked polylactic acid (PLA) and thermoplastic polyurethane (TPU) blend is made into nanofiber networks via electrospinning. The PLA/TPU weight ratio is optimized to obtain a maximum attainable strain of 100% while maintaining its mechanical integrity. The TPU/PLA fibers also allowed for their thermally activated recovery due to shape memory properties of the substrate. This novel feature enhances the sensor’s performance as it is no longer limited by its plastic deformation. Using spray coating method, a homogeneous layer of single-walled carbon nanotube is deposited onto the as-spun fiber mat to induce electrical conductivity to the surface of the fibers. It is shown that stretching and bending the sensor result in a highly sensitive and linear response with a maximum gauge factor of 33.

High-Performance Flexible All-Solid-State Asymmetric Supercapacitors Based on Vertically Aligned CuSe@Co(OH) 2 Nanosheet Arrays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gong, Jiangfeng; Tian, Yazhou; Yang, Ziyuan

The developments of electrode active materials provide the opportunities for next-generation energy storage devices. The arrangement of electrode materials on the substrate has recently emerged as a promising strategy for preparing high-performance supercapacitors. In this paper, we demonstrate a novel vertically aligned CuSe@Co(OH) 2 nanosheet arrays electrode for supercapacitor application. The materials are thoroughly characterized by structural and spectroscopic techniques. Electrochemical performance of CuSe@Co(OH) 2 nanosheet arrays are investigated in detail, which exhibit a specific capacitance as much as 1180 F g -1 at a current density of 1 A g -1. A flexible asymmetric all-solid-state supercapacitor is fabricated usingmore » CuSe@Co(OH) 2 nanosheet arrays as the positive electrode and activated carbon as the negative electrode. The device delivers a volumetric capacitance of 441.4 mF cm -3 with maximum energy density and maximum power density is 0.17 and 62.1 mW cm -3, as well as robust cycling stability (~80.4% capacitance retention after 10 000 cycles), excellent flexibility, and mechanical stability. Finally, the excellent electrochemical performance can be attributed to its unique vertically aligned configuration.« less

A systemic approach to explore the flexibility of energy stores at the cellular scale: Examples from muscle cells.

PubMed

Taghipoor, Masoomeh; van Milgen, Jaap; Gondret, Florence

2016-09-07

Variations in energy storage and expenditure are key elements for animals adaptation to rapidly changing environments. Because of the multiplicity of metabolic pathways, metabolic crossroads and interactions between anabolic and catabolic processes within and between different cells, the flexibility of energy stores in animal cells is difficult to describe by simple verbal, textual or graphic terms. We propose a mathematical model to study the influence of internal and external challenges on the dynamic behavior of energy stores and its consequence on cell energy status. The role of the flexibility of energy stores on the energy equilibrium at the cellular level is illustrated through three case studies: variation in eating frequency (i.e., glucose input), level of physical activity (i.e., ATP requirement), and changes in cell characteristics (i.e., maximum capacity of glycogen storage). Sensitivity analysis has been performed to highlight the most relevant parameters of the model; model simulations have then been performed to illustrate how variation in these key parameters affects cellular energy balance. According to this analysis, glycogen maximum accumulation capacity and homeostatic energy demand are among the most important parameters regulating muscle cell metabolism to ensure its energy equilibrium. Copyright © 2016 Elsevier Ltd. All rights reserved.

High-Performance Flexible All-Solid-State Asymmetric Supercapacitors Based on Vertically Aligned CuSe@Co(OH) 2 Nanosheet Arrays

DOE PAGES

Gong, Jiangfeng; Tian, Yazhou; Yang, Ziyuan; ...

2018-01-04

The developments of electrode active materials provide the opportunities for next-generation energy storage devices. The arrangement of electrode materials on the substrate has recently emerged as a promising strategy for preparing high-performance supercapacitors. In this paper, we demonstrate a novel vertically aligned CuSe@Co(OH) 2 nanosheet arrays electrode for supercapacitor application. The materials are thoroughly characterized by structural and spectroscopic techniques. Electrochemical performance of CuSe@Co(OH) 2 nanosheet arrays are investigated in detail, which exhibit a specific capacitance as much as 1180 F g -1 at a current density of 1 A g -1. A flexible asymmetric all-solid-state supercapacitor is fabricated usingmore » CuSe@Co(OH) 2 nanosheet arrays as the positive electrode and activated carbon as the negative electrode. The device delivers a volumetric capacitance of 441.4 mF cm -3 with maximum energy density and maximum power density is 0.17 and 62.1 mW cm -3, as well as robust cycling stability (~80.4% capacitance retention after 10 000 cycles), excellent flexibility, and mechanical stability. Finally, the excellent electrochemical performance can be attributed to its unique vertically aligned configuration.« less

3-V Solid-State Flexible Supercapacitors with Ionic-Liquid-Based Polymer Gel Electrolyte for AC Line Filtering.

PubMed

Kang, Yu Jin; Yoo, Yongju; Kim, Woong

2016-06-08

State-of-the-art solid-state flexible supercapacitors with sufficiently fast response speed for AC line filtering application suffer from limited energy density. One of the main causes of the low energy density is the low cell voltage (1 V), which is limited by aqueous-solution-based gel electrolytes. In this work, we demonstrate for the first time a 3-V flexible supercapacitor for AC line filtering based on an ionic-liquid-based polymer gel electrolyte and carbon nanotube electrode material. The flexible supercapacitor exhibits an areal energy density that is more than 20 times higher than that of the previously demonstrated 1-V flexible supercapacitor (0.66 vs 0.03 μWh/cm(2)) while maintaining excellent capacitive behavior at 120 Hz. The supercapacitor shows a maximum areal power density of 1.5 W/cm(2) and a time constant of 1 ms. The improvement of the cell voltage while maintaining the fast-response capability greatly improves the potential of supercapacitors for high-frequency applications in wearable and/or portable electronics.

Evidence for a maximum mass cut-off in the neutron star mass distribution and constraints on the equation of state

NASA Astrophysics Data System (ADS)

Alsing, Justin; Silva, Hector O.; Berti, Emanuele

2018-07-01

We infer the mass distribution of neutron stars in binary systems using a flexible Gaussian mixture model and use Bayesian model selection to explore evidence for multimodality and a sharp cut-off in the mass distribution. We find overwhelming evidence for a bimodal distribution, in agreement with previous literature, and report for the first time positive evidence for a sharp cut-off at a maximum neutron star mass. We measure the maximum mass to be 2.0 M⊙ < mmax < 2.2 M⊙ (68 per cent), 2.0 M⊙ < mmax < 2.6 M⊙ (90 per cent), and evidence for a cut-off is robust against the choice of model for the mass distribution and to removing the most extreme (highest mass) neutron stars from the data set. If this sharp cut-off is interpreted as the maximum stable neutron star mass allowed by the equation of state of dense matter, our measurement puts constraints on the equation of state. For a set of realistic equations of state that support >2 M⊙ neutron stars, our inference of mmax is able to distinguish between models at odds ratios of up to 12:1, whilst under a flexible piecewise polytropic equation-of-state model our maximum mass measurement improves constraints on the pressure at 3-7× the nuclear saturation density by ˜ 30-50 per cent compared to simply requiring mmax > 2 M⊙. We obtain a lower bound on the maximum sound speed attained inside the neutron star of c_ s^max > 0.63c (99.8 per cent), ruling out c_ s^max < c/√{3} at high significance. Our constraints on the maximum neutron star mass strengthen the case for neutron star-neutron star mergers as the primary source of short gamma-ray bursts.

The Flexible Care Service: a third-sector service for older people with mental health needs.

PubMed

Ryder, Elaine

2015-01-01

Demographic patterns indicate that by 2030, one in five people in England will be over 65. Together with the fact that as people age they are more likely to suffer from comorbidities, it is of paramount importance that local services are designed to meet the needs of individual older people. The Flexible Care Service is a resource for older people with mental health problems. Through the use of client case studies, the Department of Health's 'six Cs' (care, compassion, competence, communication, courage and commitment) are used as a framework to demonstrate how a third-sector service such as Flexible Care can offer a person-centred approach in order to meet the diverse needs of individual clients. The framework is also used to demonstrate the high level of skills needed by flexible carers in order to provide this support.

Highly efficient Cu(In,Ga)Se2 solar cells grown on flexible polymer films.

PubMed

Chirilă, Adrian; Buecheler, Stephan; Pianezzi, Fabian; Bloesch, Patrick; Gretener, Christina; Uhl, Alexander R; Fella, Carolin; Kranz, Lukas; Perrenoud, Julian; Seyrling, Sieghard; Verma, Rajneesh; Nishiwaki, Shiro; Romanyuk, Yaroslav E; Bilger, Gerhard; Tiwari, Ayodhya N

2011-09-18

Solar cells based on polycrystalline Cu(In,Ga)Se(2) absorber layers have yielded the highest conversion efficiency among all thin-film technologies, and the use of flexible polymer films as substrates offers several advantages in lowering manufacturing costs. However, given that conversion efficiency is crucial for cost-competitiveness, it is necessary to develop devices on flexible substrates that perform as well as those obtained on rigid substrates. Such comparable performance has not previously been achieved, primarily because polymer films require much lower substrate temperatures during absorber deposition, generally resulting in much lower efficiencies. Here we identify a strong composition gradient in the absorber layer as the main reason for inferior performance and show that, by adjusting it appropriately, very high efficiencies can be obtained. This implies that future manufacturing of highly efficient flexible solar cells could lower the cost of solar electricity and thus become a significant branch of the photovoltaic industry.

Continuous Passive Motion: The No-Exercise Exercise.

ERIC Educational Resources Information Center

Gauthier, Michele M.

1987-01-01

Continuous passive motion (CPM) tables, originally developed as therapeutic tools, are becoming popular in health salons in spite of the fact that they offer little to healthy people in terms of inch loss, circulaiton, and flexibility. (Author/CB)

76 FR 69311 - Self-Regulatory Organizations; NYSE Arca, Inc.; Notice of Filing and Immediate Effectiveness of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-08

...'') and broker-dealers increased authority and flexibility to offer new and unique market data to..., providing virtually limitless opportunities for entrepreneurs who wish to produce and distribute their own...

Organic materials for printed electronics

NASA Astrophysics Data System (ADS)

Berggren, M.; Nilsson, D.; Robinson, N. D.

2007-01-01

Organic materials can offer a low-cost alternative for printed electronics and flexible displays. However, research in these systems must exploit the differences - via molecular-level control of functionality - compared with inorganic electronics if they are to become commercially viable.

Improving transit equity, streamlining operations : technologies that benefit the transportation disadvantaged

DOT National Transportation Integrated Search

2006-01-01

This illustrates some of the ways in which technology has improved the ability of transportation disadvantaged individuals to use public transit. Some benefits offered include more efficient coordination among service providers, system flexibility, t...

Always on Sundays: School With No Walls, No Doors, No Bureaucracy

ERIC Educational Resources Information Center

Sheats, June Dow

1974-01-01

An experimental open air school for adults and youth which meets weekly in Chapultepec Park offers arts and crafts, vocational studies, languages, literacy, theater, sports, and other courses in a flexible format. (MS)

State Infrastructure Banks: A Mechanism to Expand Federal Transportation Financing

DOT National Transportation Integrated Search

1996-10-01

State Infrastructure Banks (SIBs) are intended to complement traditional transportation grant programs and provide states with increased flexibility to offer many types of financial assistance, such as loans and subsidized interest rates, and provide...

Stretchable spiral thin-film battery capable of out-of-plane deformation

NASA Astrophysics Data System (ADS)

Kammoun, Mejdi; Berg, Sean; Ardebili, Haleh

2016-11-01

There is a compelling need for innovative design concepts in energy storage devices such as flexible and stretchable batteries that can simultaneously provide electrochemical and mechanical functions to accommodate nonconventional applications including wearable and implantable devices. In this study, we report on the design and fabrication of a stretchable spiral thin-film lithium ion battery that is capable of large out-of-plane deformation of 1300% while exhibiting simultaneous electrochemical functionality. The spiral battery is fabricated using a flexible solid polymer nanocomposite electrolyte film that offers enhanced safety and stability compared to the conventional organic liquid-based electrolyte. The spiral lithium ion battery exhibits robust mechanical stretchability over 9000 stretching cycles and an energy density of 4.862 mWh/cm3 at ∼650% out-of-plane deformation. Finite element analysis of the spiral battery offers insights about the nature of stresses and strains during battery stretching.

A colour-tunable, weavable fibre-shaped polymer light-emitting electrochemical cell

NASA Astrophysics Data System (ADS)

Zhang, Zhitao; Guo, Kunping; Li, Yiming; Li, Xueyi; Guan, Guozhen; Li, Houpu; Luo, Yongfeng; Zhao, Fangyuan; Zhang, Qi; Wei, Bin; Pei, Qibing; Peng, Huisheng

2015-04-01

The emergence of wearable electronics and optoelectronics requires the development of devices that are not only highly flexible but can also be woven into textiles to offer a truly integrated solution. Here, we report a colour-tunable, weavable fibre-shaped polymer light-emitting electrochemical cell (PLEC). The fibre-shaped PLEC is fabricated using all-solution-based processes that can be scaled up for practical applications. The design has a coaxial structure comprising a modified metal wire cathode and a conducting aligned carbon nanotube sheet anode, with an electroluminescent polymer layer sandwiched between them. The fibre shape offers unique and promising advantages. For example, the luminance is independent of viewing angle, the fibre-shaped PLEC can provide a variety of different and tunable colours, it is lightweight, flexible and wearable, and it can potentially be woven into light-emitting clothes for the creation of smart fabrics.

Ureteric bupivicaine infusion for loin pain haematuria syndrome

PubMed Central

Ahmed, P; Acher, P; Deane, AM

2010-01-01

INTRODUCTION Loin pain haematuria syndrome is a common problem with complications including opiate dependence. Morbidity treatments include intra-ureteric capsaicin infusion, nephrectomy, autotransplantation and nephrolysis. We explored the use of flexible cystoscopic infusion of intra-ureteric bupivicaine. PATIENTS AND METHODS Patients presenting with chronic loin pain underwent urological and nephrological evaluation. Bupivicaine (0.5%, 20 ml) was infused via an intra-ureteric catheter under flexible cystoscopic guidance. Repeat infusions were offered if indicated. RESULTS Sixteen of 17 patients with 1-year follow-up responded and were satisfied. Twelve of these required repeat infusions (mean, 2.9 infusions). The procedures were well tolerated by all patients without adverse effects. CONCLUSIONS Intra-ureteric bupivicaine infusion has a place in the management of patients with chronic renal pain. It offers a minimally invasive alternative to other treatments. This procedure warrants further investigation within a randomised, controlled trial setting. PMID:20353642

46 CFR 56.30-40 - Flexible pipe couplings of the compression or slip-on type.

Code of Federal Regulations, 2011 CFR

2011-10-01

... or slip-on type must not be used as expansion joints. To ensure that the maximum axial displacement... couplings must not be used in cargo holds or in any other space where leakage, undetected flooding, or...

46 CFR 56.30-40 - Flexible pipe couplings of the compression or slip-on type.

Code of Federal Regulations, 2012 CFR

2012-10-01

... or slip-on type must not be used as expansion joints. To ensure that the maximum axial displacement... couplings must not be used in cargo holds or in any other space where leakage, undetected flooding, or...

46 CFR 56.30-40 - Flexible pipe couplings of the compression or slip-on type.

Code of Federal Regulations, 2014 CFR

2014-10-01

... or slip-on type must not be used as expansion joints. To ensure that the maximum axial displacement... couplings must not be used in cargo holds or in any other space where leakage, undetected flooding, or...

46 CFR 56.30-40 - Flexible pipe couplings of the compression or slip-on type.

Code of Federal Regulations, 2013 CFR

2013-10-01

... or slip-on type must not be used as expansion joints. To ensure that the maximum axial displacement... couplings must not be used in cargo holds or in any other space where leakage, undetected flooding, or...

46 CFR 56.30-40 - Flexible pipe couplings of the compression or slip-on type.

Code of Federal Regulations, 2010 CFR

2010-10-01

... or slip-on type must not be used as expansion joints. To ensure that the maximum axial displacement... couplings must not be used in cargo holds or in any other space where leakage, undetected flooding, or...

29 CFR 1926.407 - Hazardous (classified) locations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... marking requirement for specific equipment: (A) Equipment of the non-heat-producing type (such as junction boxes, conduit, and fitting) and equipment of the heat-producing type having a maximum temperature of... connections, conductor insulation, flexible cords, sealing and drainage, transformers, capacitors, switches...

29 CFR 1926.407 - Hazardous (classified) locations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... marking requirement for specific equipment: (A) Equipment of the non-heat-producing type (such as junction boxes, conduit, and fitting) and equipment of the heat-producing type having a maximum temperature of... connections, conductor insulation, flexible cords, sealing and drainage, transformers, capacitors, switches...

29 CFR 1926.407 - Hazardous (classified) locations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... marking requirement for specific equipment: (A) Equipment of the non-heat-producing type (such as junction boxes, conduit, and fitting) and equipment of the heat-producing type having a maximum temperature of... connections, conductor insulation, flexible cords, sealing and drainage, transformers, capacitors, switches...

Benefits and Limitations of Real Options Analysis for the Practice of River Flood Risk Management

NASA Astrophysics Data System (ADS)

Kind, Jarl M.; Baayen, Jorn H.; Botzen, W. J. Wouter

2018-04-01

Decisions on long-lived flood risk management (FRM) investments are complex because the future is uncertain. Flexibility and robustness can be used to deal with future uncertainty. Real options analysis (ROA) provides a welfare-economics framework to design and evaluate robust and flexible FRM strategies under risk or uncertainty. Although its potential benefits are large, ROA is hardly used in todays' FRM practice. In this paper, we investigate benefits and limitations of a ROA, by applying it to a realistic FRM case study for an entire river branch. We illustrate how ROA identifies optimal short-term investments and values future options. We develop robust dike investment strategies and value the flexibility offered by additional room for the river measures. We benchmark the results of ROA against those of a standard cost-benefit analysis and show ROA's potential policy implications. The ROA for a realistic case requires a high level of geographical detail, a large ensemble of scenarios, and the inclusion of stakeholders' preferences. We found several limitations of applying the ROA. It is complex. In particular, relevant sources of uncertainty need to be recognized, quantified, integrated, and discretized in scenarios, requiring subjective choices and expert judgment. Decision trees have to be generated and stakeholders' preferences have to be translated into decision rules. On basis of this study, we give general recommendations to use high discharge scenarios for the design of measures with high fixed costs and few alternatives. Lower scenarios may be used when alternatives offer future flexibility.

Quantifying intracellular rates of glycolytic and oxidative ATP production and consumption using extracellular flux measurements

PubMed Central

Mookerjee, Shona A.; Gerencser, Akos A.; Nicholls, David G.; Brand, Martin D.

2017-01-01

Partitioning of ATP generation between glycolysis and oxidative phosphorylation is central to cellular bioenergetics but cumbersome to measure. We describe here how rates of ATP generation by each pathway can be calculated from simultaneous measurements of extracellular acidification and oxygen consumption. We update theoretical maximum ATP yields by mitochondria and cells catabolizing different substrates. Mitochondrial P/O ratios (mol of ATP generated per mol of [O] consumed) are 2.73 for oxidation of pyruvate plus malate and 1.64 for oxidation of succinate. Complete oxidation of glucose by cells yields up to 33.45 ATP/glucose with a maximum P/O of 2.79. We introduce novel indices to quantify bioenergetic phenotypes. The glycolytic index reports the proportion of ATP production from glycolysis and identifies cells as primarily glycolytic (glycolytic index > 50%) or primarily oxidative. The Warburg effect is a chronic increase in glycolytic index, quantified by the Warburg index. Additional indices quantify the acute flexibility of ATP supply. The Crabtree index and Pasteur index quantify the responses of oxidative and glycolytic ATP production to alterations in glycolysis and oxidative reactions, respectively; the supply flexibility index quantifies overall flexibility of ATP supply; and the bioenergetic capacity quantifies the maximum rate of total ATP production. We illustrate the determination of these indices using C2C12 myoblasts. Measurement of ATP use revealed no significant preference for glycolytic or oxidative ATP by specific ATP consumers. Overall, we demonstrate how extracellular fluxes quantitatively reflect intracellular ATP turnover and cellular bioenergetics. We provide a simple spreadsheet to calculate glycolytic and oxidative ATP production rates from raw extracellular acidification and respiration data. PMID:28270511

In vivo histology: optical biopsies with chemical contrast using clinical multiphoton/coherent anti-Stokes Raman scattering tomography

NASA Astrophysics Data System (ADS)

Weinigel, M.; Breunig, H. G.; Kellner-Höfer, M.; Bückle, R.; Darvin, M. E.; Klemp, M.; Lademann, J.; König, K.

2014-05-01

The majority of existing coherent anti-Stokes Raman scattering (CARS) imaging systems are still huge and complicated laboratory systems and neither compact nor user-friendly nor mobile medically certified CARS systems. We have developed a new flexible multiphoton/CARS tomograph for imaging in a clinical environment. The system offers exceptional 360° flexibility with a very stable setup and enables label free ‘in vivo histology’ with chemical contrast within seconds. It can be completely operated by briefly trained non-laser experts. The imaging capability and flexibility of the novel in vivo tomograph are shown on optical biopsies with subcellular resolution and chemical contrast of patients suffering from psoriasis and squamous cell carcinoma.

Miniaturized soft bio-hybrid robotics: a step forward into healthcare applications.

PubMed

Patino, T; Mestre, R; Sánchez, S

2016-10-07

Soft robotics is an emerging discipline that employs soft flexible materials such as fluids, gels and elastomers in order to enhance the use of robotics in healthcare applications. Compared to their rigid counterparts, soft robotic systems have flexible and rheological properties that are closely related to biological systems, thus allowing the development of adaptive and flexible interactions with complex dynamic environments. With new technologies arising in bioengineering, the integration of living cells into soft robotic systems offers the possibility of accomplishing multiple complex functions such as sensing and actuating upon external stimuli. These emerging bio-hybrid systems are showing promising outcomes and opening up new avenues in the field of soft robotics for applications in healthcare and other fields.

NASA Workshop on Distributed Parameter Modeling and Control of Flexible Aerospace Systems

NASA Technical Reports Server (NTRS)

Marks, Virginia B. (Compiler); Keckler, Claude R. (Compiler)

1994-01-01

Although significant advances have been made in modeling and controlling flexible systems, there remains a need for improvements in model accuracy and in control performance. The finite element models of flexible systems are unduly complex and are almost intractable to optimum parameter estimation for refinement using experimental data. Distributed parameter or continuum modeling offers some advantages and some challenges in both modeling and control. Continuum models often result in a significantly reduced number of model parameters, thereby enabling optimum parameter estimation. The dynamic equations of motion of continuum models provide the advantage of allowing the embedding of the control system dynamics, thus forming a complete set of system dynamics. There is also increased insight provided by the continuum model approach.

All-Solution-Processed Metal-Oxide-Free Flexible Organic Solar Cells with Over 10% Efficiency.

PubMed

Song, Wei; Fan, Xi; Xu, Bingang; Yan, Feng; Cui, Huiqin; Wei, Qiang; Peng, Ruixiang; Hong, Ling; Huang, Jiaming; Ge, Ziyi

2018-05-16

All-solution-processing at low temperatures is important and desirable for making printed photovoltaic devices and also offers the possibility of a safe and cost-effective fabrication environment for the devices. Herein, an all-solution-processed flexible organic solar cell (OSC) using poly(3,4-ethylenedioxythiophene):poly-(styrenesulfonate) electrodes is reported. The all-solution-processed flexible devices yield the highest power conversion efficiency of 10.12% with high fill factor of over 70%, which is the highest value for metal-oxide-free flexible OSCs reported so far. The enhanced performance is attributed to the newly developed gentle acid treatment at room temperature that enables a high-performance PEDOT:PSS/plastic underlying substrate with a matched work function (≈4.91 eV), and the interface engineering that endows the devices with better interface contacts and improved hole mobility. Furthermore, the flexible devices exhibit an excellent mechanical flexibility, as indicated by a high retention (≈94%) of the initial efficiency after 1000 bending cycles. This work provides a simple route to fabricate high-performance all-solution-processed flexible OSCs, which is important for the development of printing, blading, and roll-to-roll technologies. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The School Store of the New Millennium: The E-School Store.

ERIC Educational Resources Information Center

Yohon, Teresa; Gallegos, Jack L.

2000-01-01

Discusses the advantages of having an online school store including ease of access, longer hours, and reduced and/or flexible staffing. Offers suggestions for starting an online store including selection of an Internet service provider.(JOW)

Should HR Control Training?

ERIC Educational Resources Information Center

Schettler, Joel

2002-01-01

Discusses the debate over whether the training department of a company should be placed within human resources. Offers opinions of training and human resources executives and concludes that a varied structure enables training to remain flexible in response to changing conditions. (JOW)

Ten Tips for Leadership.

ERIC Educational Resources Information Center

Howe, Eleanor B.

2001-01-01

Discusses ten attributes of leadership and offers suggestions for school librarians to implement them. Highlights include communicating vision and ideas; ethical values and integrity; self-awareness and self-knowledge; context; cooperation; diverse skills and flexibility; organizational development; personal growth; and taking action. (LRW)

Texas M-E flexible pavement design system: literature review and proposed framework.

DOT National Transportation Integrated Search

2012-04-01

Recent developments over last several decades have offered an opportunity for more rational and rigorous pavement design procedures. Substantial work has already been completed in Texas, nationally, and internationally, in all aspects of modeling, ma...

3 CFR 9053 - Proclamation 9053 of October 31, 2013. National Family Caregivers Month, 2013

Code of Federal Regulations, 2014 CFR

2014-01-01

... role they play in our healthcare system is one we must recognize and support. During National Family... themselves, we must offer our appreciation and flexibility, in our healthcare system, our workplaces, and our...

45 CFR 98.1 - Goals and purposes.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND... each State maximum flexibility in developing child care programs and policies that best suit the needs of children and parents within the State; (2) Promote parental choice to empower working parents to...

Dynamic Behaviour and Seismic Response of Ground Supported Cylindrical Water Tanks

NASA Astrophysics Data System (ADS)

Asha, Joseph; Glory, Joseph

2018-05-01

Liquid storage tank such as in water distribution systems, petroleum plants etc., constitute a vital component of life line systems. Reducing earthquake effects on liquid storage tanks, to minimize the environmental and economic impact of these effects, have always been an important engineering concern. In this paper, the dynamic behavior of cylindrical ground supported concrete water tanks with different aspect ratios is investigated using finite element software ANSYS. The natural frequencies and modal responses are obtained for impulsive and convective modes of vibration. The natural frequency of vibration of the tank is observed to be the lowest at maximum water depth. The fundamental impulsive frequency increases as water level reduces and for water level less than 1/3 of tank height, there is significantly no change in impulsive frequency. The effect of wall flexibility on dynamic behavior of the tank is investigated by performing the modal analysis of flexible and rigid tanks. For a partially filled tank, the results of the present study are of significant relevance. The response of the tank to the transient loading as horizontal ground motion of El Centro earthquake is studied for various water heights. As the height of water on the tank increases, the ultimate maximum seismic response parameters are also observed to be increased. The location of maximum hoop stress varies in accordance with the variations in input ground motion and water fill condition whereas shear and bending moment are maximum at the base.

A basic introduction to the thermodynamics of the Earth system far from equilibrium and maximum entropy production

PubMed Central

Kleidon, A.

2010-01-01

The Earth system is remarkably different from its planetary neighbours in that it shows pronounced, strong global cycling of matter. These global cycles result in the maintenance of a unique thermodynamic state of the Earth's atmosphere which is far from thermodynamic equilibrium (TE). Here, I provide a simple introduction of the thermodynamic basis to understand why Earth system processes operate so far away from TE. I use a simple toy model to illustrate the application of non-equilibrium thermodynamics and to classify applications of the proposed principle of maximum entropy production (MEP) to such processes into three different cases of contrasting flexibility in the boundary conditions. I then provide a brief overview of the different processes within the Earth system that produce entropy, review actual examples of MEP in environmental and ecological systems, and discuss the role of interactions among dissipative processes in making boundary conditions more flexible. I close with a brief summary and conclusion. PMID:20368248

Horizontal lifelines - review of regulations and simple design method considering anchorage rigidity.

PubMed

Galy, Bertrand; Lan, André

2018-03-01

Among the many occupational risks construction workers encounter every day falling from a height is the most dangerous. The objective of this article is to propose a simple analytical design method for horizontal lifelines (HLLs) that considers anchorage flexibility. The article presents a short review of the standards and regulations/acts/codes concerning HLLs in Canada the USA and Europe. A static analytical approach is proposed considering anchorage flexibility. The analytical results are compared with a series of 42 dynamic fall tests and a SAP2000 numerical model. The experimental results show that the analytical method is a little conservative and overestimates the line tension in most cases with a maximum of 17%. The static SAP2000 results show a maximum 2.1% difference with the analytical method. The analytical method is accurate enough to safely design HLLs and quick design abaci are provided to allow the engineer to make quick on-site verification if needed.

A basic introduction to the thermodynamics of the Earth system far from equilibrium and maximum entropy production.

PubMed

Kleidon, A

2010-05-12

The Earth system is remarkably different from its planetary neighbours in that it shows pronounced, strong global cycling of matter. These global cycles result in the maintenance of a unique thermodynamic state of the Earth's atmosphere which is far from thermodynamic equilibrium (TE). Here, I provide a simple introduction of the thermodynamic basis to understand why Earth system processes operate so far away from TE. I use a simple toy model to illustrate the application of non-equilibrium thermodynamics and to classify applications of the proposed principle of maximum entropy production (MEP) to such processes into three different cases of contrasting flexibility in the boundary conditions. I then provide a brief overview of the different processes within the Earth system that produce entropy, review actual examples of MEP in environmental and ecological systems, and discuss the role of interactions among dissipative processes in making boundary conditions more flexible. I close with a brief summary and conclusion.

Tensile characteristics of metal nanoparticle films on flexible polymer substrates for printed electronics applications.

PubMed

Kim, Sanghyeok; Won, Sejeong; Sim, Gi-Dong; Park, Inkyu; Lee, Soon-Bok

2013-03-01

Metal nanoparticle solutions are widely used for the fabrication of printed electronic devices. The mechanical properties of the solution-processed metal nanoparticle thin films are very important for the robust and reliable operation of printed electronic devices. In this paper, we report the tensile characteristics of silver nanoparticle (Ag NP) thin films on flexible polymer substrates by observing the microstructures and measuring the electrical resistance under tensile strain. The effects of the annealing temperatures and periods of Ag NP thin films on their failure strains are explained with a microstructural investigation. The maximum failure strain for Ag NP thin film was 6.6% after initial sintering at 150 °C for 30 min. Thermal annealing at higher temperatures for longer periods resulted in a reduction of the maximum failure strain, presumably due to higher porosity and larger pore size. We also found that solution-processed Ag NP thin films have lower failure strains than those of electron beam evaporated Ag thin films due to their highly porous film morphologies.

Recent progress in flexible OLED displays

NASA Astrophysics Data System (ADS)

Hack, Michael G.; Weaver, Michael S.; Mahon, Janice K.; Brown, Julie J.

2001-09-01

Organic light emitting device (OLED) technology has recently been shown to demonstrate excellent performance and cost characteristics for use in numerous flat panel display (FPD) applications. OLED displays emit bright, colorful light with excellent power efficiency, wide viewing angle and video response rates. OLEDs are also demonstrating the requisite environmental robustness for a wide variety of applications. OLED technology is also the first FPD technology with the potential to be highly functional and durable in a flexible format. The use of plastic and other flexible substrate materials offers numerous advantages over commonly used glass substrates, including impact resistance, light weight, thinness and conformability. Currently, OLED displays are being fabricated on rigid substrates, such as glass or silicon wafers. At Universal Display Corporation (UDC), we are developing a new class of flexible OLED displays (FOLEDs). These displays also have extremely low power consumption through the use of electrophosphorescent doped OLEDs. To commercialize FOLED technology, a number of technical issues related to packaging and display processing on flexible substrates need to be addressed. In this paper, we report on our recent results to demonstrate the key technologies that enable the manufacture of power efficient, long-life flexible OLED displays for commercial and military applications.

Inflexible daily behaviour is associated with the ability to control an automatic reaction in autism spectrum disorder.

PubMed

Tei, Shisei; Fujino, Junya; Hashimoto, Ryu-Ichiro; Itahashi, Takashi; Ohta, Haruhisa; Kanai, Chieko; Kubota, Manabu; Nakamura, Motoaki; Kato, Nobumasa; Takahashi, Hidehiko

2018-05-24

Inflexible behaviours in people with autism spectrum disorder (ASD) broadly obstruct social communication. Meanwhile, flexibility implicates cognitive control to resolve socially conflicting situations; however, it remains unclear how people with ASD behave in the face of these conflicts in this respect. We used the ultimatum game (UG) and the implicit-association test (IAT) to examine goal-directed/economic flexibility, both of which involve conflict and cognitive control. In addition, we used the Detail and Flexibility Questionnaire (DFlex) to measure inflexible everyday behaviour with diminished cognitive control and attention shifting. We observed the decreased flexibility in participants with ASD (DFlex and IAT); further, their IAT scores positively correlated with DFlex. However, in the UG, contrary to our prediction, participants with ASD accepted unfair offers more frequently than TD. These results suggest that assessing the automatic/attention processing level with the IAT could be a useful approach to study behavioural flexibility among ASD compared with the UG, which might comprise multiple response strategies besides economic rationality. Overall, the severity of inflexible daily behaviours in people with ASD may be associated with a reduced flexible attitude at an automatic level, altered attention processing and decreased cognitive control.

Learning Technology Adoption: Navy Barriers And Resistance

DTIC Science & Technology

2018-03-01

ABSTRACT (maximum 200 words) Technological developments offer opportunities to enhance training effectiveness, in support of achieving high-velocity...developments offer opportunities to enhance training effectiveness, in support of achieving high-velocity learning. However, resistance to change...considering what opportunities for enhanced training might be offered by learning-centered technologies. This is evident in the CNO’s statement, “We must

Characterization of polymer silver pastes for screen printed flexible RFID antennas

NASA Astrophysics Data System (ADS)

Janeczek, Kamil; Jakubowska, Małgorzata; Futera, Konrad; MłoŻniak, Anna; Kozioł, GraŻyna; Araźna, Aneta

Radio Frequency Identification (RFID) systems have become more and more popular in the last few years because of their wide application fields, such as supply chain management and logistics. To continue their development further investigations of new conductive materials for fabrication of RFID transponders' antennas are necessary to be carried out. These materials should provide high flexibility and good radiation performance of printed antennas. In this paper, two polymer silver pastes based on silver flakes were characterized with regard to manufacturing of flexible RFID antennas with screen printing technique. Foil and paper were used as a substrate materials. Surface profile of the printed antennas was measured using an optical profilometer and their resistance was measured with a four-point-probe method. Antenna flexibility was evaluated in cyclic bending tests and its performance with reflection coefficient measurements with the use of differential probe connected to a vector network analyzer. In addition, a maximum read distance of a fabricated RFID transponder was measured.

Flexible polymer transistors with high pressure sensitivity for application in electronic skin and health monitoring

NASA Astrophysics Data System (ADS)

Schwartz, Gregor; Tee, Benjamin C.-K.; Mei, Jianguo; Appleton, Anthony L.; Kim, Do Hwan; Wang, Huiliang; Bao, Zhenan

2013-05-01

Flexible pressure sensors are essential parts of an electronic skin to allow future biomedical prostheses and robots to naturally interact with humans and the environment. Mobile biomonitoring in long-term medical diagnostics is another attractive application for these sensors. Here we report the fabrication of flexible pressure-sensitive organic thin film transistors with a maximum sensitivity of 8.4 kPa-1, a fast response time of <10 ms, high stability over >15,000 cycles and a low power consumption of <1 mW. The combination of a microstructured polydimethylsiloxane dielectric and the high-mobility semiconducting polyisoindigobithiophene-siloxane in a monolithic transistor design enabled us to operate the devices in the subthreshold regime, where the capacitance change upon compression of the dielectric is strongly amplified. We demonstrate that our sensors can be used for non-invasive, high fidelity, continuous radial artery pulse wave monitoring, which may lead to the use of flexible pressure sensors in mobile health monitoring and remote diagnostics in cardiovascular medicine.

Real-Time Remote Monitoring of Temperature and Humidity Within a Proton Exchange Membrane Fuel Cell Using Flexible Sensors

PubMed Central

Kuo, Long-Sheng; Huang, Hao-Hsiu; Yang, Cheng-Hao; Chen, Ping-Hei

2011-01-01

This study developed portable, non-invasive flexible humidity and temperature microsensors and an in situ wireless sensing system for a proton exchange membrane fuel cell (PEMFC). The system integrated three parts: a flexible capacitive humidity microsensor, a flexible resistive temperature microsensor, and a radio frequency (RF) module for signal transmission. The results show that the capacitive humidity microsensor has a high sensitivity of 0.83 pF%RH−1 and the resistive temperature microsensor also exhibits a high sensitivity of 2.94 × 10−3 °C−1. The established RF module transmits the signals from the two microsensors. The transmission distance can reach 4 m and the response time is less than 0.25 s. The performance measurements demonstrate that the maximum power density of the fuel cell with and without these microsensors are 14.76 mW·cm−2 and 15.90 mW·cm−2, with only 7.17% power loss. PMID:22164099

Flexible polymer transistors with high pressure sensitivity for application in electronic skin and health monitoring.

PubMed

Schwartz, Gregor; Tee, Benjamin C-K; Mei, Jianguo; Appleton, Anthony L; Kim, Do Hwan; Wang, Huiliang; Bao, Zhenan

2013-01-01

Flexible pressure sensors are essential parts of an electronic skin to allow future biomedical prostheses and robots to naturally interact with humans and the environment. Mobile biomonitoring in long-term medical diagnostics is another attractive application for these sensors. Here we report the fabrication of flexible pressure-sensitive organic thin film transistors with a maximum sensitivity of 8.4 kPa(-1), a fast response time of <10 ms, high stability over >15,000 cycles and a low power consumption of <1 mW. The combination of a microstructured polydimethylsiloxane dielectric and the high-mobility semiconducting polyisoindigobithiophene-siloxane in a monolithic transistor design enabled us to operate the devices in the subthreshold regime, where the capacitance change upon compression of the dielectric is strongly amplified. We demonstrate that our sensors can be used for non-invasive, high fidelity, continuous radial artery pulse wave monitoring, which may lead to the use of flexible pressure sensors in mobile health monitoring and remote diagnostics in cardiovascular medicine.

Co-Design Method and Wafer-Level Packaging Technique of Thin-Film Flexible Antenna and Silicon CMOS Rectifier Chips for Wireless-Powered Neural Interface Systems.

PubMed

Okabe, Kenji; Jeewan, Horagodage Prabhath; Yamagiwa, Shota; Kawano, Takeshi; Ishida, Makoto; Akita, Ippei

2015-12-16

In this paper, a co-design method and a wafer-level packaging technique of a flexible antenna and a CMOS rectifier chip for use in a small-sized implantable system on the brain surface are proposed. The proposed co-design method optimizes the system architecture, and can help avoid the use of external matching components, resulting in the realization of a small-size system. In addition, the technique employed to assemble a silicon large-scale integration (LSI) chip on the very thin parylene film (5 μm) enables the integration of the rectifier circuits and the flexible antenna (rectenna). In the demonstration of wireless power transmission (WPT), the fabricated flexible rectenna achieved a maximum efficiency of 0.497% with a distance of 3 cm between antennas. In addition, WPT with radio waves allows a misalignment of 185% against antenna size, implying that the misalignment has a less effect on the WPT characteristics compared with electromagnetic induction.

Co-Design Method and Wafer-Level Packaging Technique of Thin-Film Flexible Antenna and Silicon CMOS Rectifier Chips for Wireless-Powered Neural Interface Systems

PubMed Central

Okabe, Kenji; Jeewan, Horagodage Prabhath; Yamagiwa, Shota; Kawano, Takeshi; Ishida, Makoto; Akita, Ippei

2015-01-01

In this paper, a co-design method and a wafer-level packaging technique of a flexible antenna and a CMOS rectifier chip for use in a small-sized implantable system on the brain surface are proposed. The proposed co-design method optimizes the system architecture, and can help avoid the use of external matching components, resulting in the realization of a small-size system. In addition, the technique employed to assemble a silicon large-scale integration (LSI) chip on the very thin parylene film (5 μm) enables the integration of the rectifier circuits and the flexible antenna (rectenna). In the demonstration of wireless power transmission (WPT), the fabricated flexible rectenna achieved a maximum efficiency of 0.497% with a distance of 3 cm between antennas. In addition, WPT with radio waves allows a misalignment of 185% against antenna size, implying that the misalignment has a less effect on the WPT characteristics compared with electromagnetic induction. PMID:26694407

Web Service Execution and Monitoring in Integrated Applications in Support of Business Communities

NASA Astrophysics Data System (ADS)

Chiriacescu, Rares M.; SzóKe, Alexandru; Portase, Sorin; Florea, Monica

Emerging technology is one of the key factors that drive the business world to faster adaptation, reaction and shorter communication path. Building upon such technologies, business communities emerge, geared toward high flexibility in their offerings and collaboration: business-to-customer and business-to-business collaborations. Adapting to the market requirements, companies must address several technical challenges that arise from the main requirements of the system they have to introduce: a high degree of flexibility, heterogeneous system collaboration and security of the transferred data.

Robotic Processing Of Rocket-Engine Nozzles

NASA Technical Reports Server (NTRS)

Gilbert, Jeffrey L.; Maslakowski, John E.; Gutow, David A.; Deily, David C.

1994-01-01

Automated manufacturing cell containing computer-controlled robotic processing system developed to implement some important related steps in fabrication of rocket-engine nozzles. Performs several tedious and repetitive fabrication, measurement, adjustment, and inspection processes and subprocesses now performed manually. Offers advantages of reduced processing time, greater consistency, excellent collection of data, objective inspections, greater productivity, and simplified fixturing. Also affords flexibility: by making suitable changes in hardware and software, possible to modify process and subprocesses. Flexibility makes work cell adaptable to fabrication of heat exchangers and other items structured similarly to rocket nozzles.

Evaluation of Precast Panels for Airfield Pavement Repair. Phase 1: System Optimization and Test Section Construction

DTIC Science & Technology

2013-06-01

boundary was also considered. The panel must be slightly smaller than the repair area to allow the panel to be installed easily with little resistance ...beam between simple supports that offer no resistance and is more flexible. The actual support conditions are somewhere in between since the...slenderness of the keyway components, and thin bolt tab were not sufficient to resist rotation. The keyway was removed since it offered little structural

Chaining for Flexible and High-Performance Key-Value Systems

DTIC Science & Technology

2012-09-01

store that is fault tolerant achieves high performance and availability, and offers strong data consistency? We present a new replication protocol...effective high performance data access and analytics, many sites use simpler data model “ NoSQL ” systems. ese systems store and retrieve data only by...DRAM, Flash, and disk-based storage; can act as an unreliable cache or a durable store ; and can offer strong or weak data consistency. e value of

An Iterative Maximum a Posteriori Estimation of Proficiency Level to Detect Multiple Local Likelihood Maxima

ERIC Educational Resources Information Center

Magis, David; Raiche, Gilles

2010-01-01

In this article the authors focus on the issue of the nonuniqueness of the maximum likelihood (ML) estimator of proficiency level in item response theory (with special attention to logistic models). The usual maximum a posteriori (MAP) method offers a good alternative within that framework; however, this article highlights some drawbacks of its…

Can enzyme engineering benefit from the modulation of protein motions? Lessons learned from NMR relaxation dispersion experiments.

PubMed

Doucet, Nicolas

2011-04-01

Despite impressive progress in protein engineering and design, our ability to create new and efficient enzyme activities remains a laborious and time-consuming endeavor. In the past few years, intricate combinations of rational mutagenesis, directed evolution and computational methods have paved the way to exciting engineering examples and are now offering a new perspective on the structural requirements of enzyme activity. However, these structure-function analyses are usually guided by the time-averaged static models offered by enzyme crystal structures, which often fail to describe the functionally relevant 'invisible states' adopted by proteins in space and time. To alleviate such limitations, NMR relaxation dispersion experiments coupled to mutagenesis studies have recently been applied to the study of enzyme catalysis, effectively complementing 'structure-function' analyses with 'flexibility-function' investigations. In addition to offering quantitative, site-specific information to help characterize residue motion, these NMR methods are now being applied to enzyme engineering purposes, providing a powerful tool to help characterize the effects of controlling long-range networks of flexible residues affecting enzyme function. Recent advancements in this emerging field are presented here, with particular attention to mutagenesis reports highlighting the relevance of NMR relaxation dispersion tools in enzyme engineering.

Thermal Performance of Composite Flexible Blanket Insulations for Hypersonic Aerospace Vehicles

NASA Technical Reports Server (NTRS)

Kourtides, Demetrius A.

1993-01-01

This paper describes the thermal performance of a Composite Flexible Blanket Insulation (C.F.B.I.) considered for potential use as a thermal protection system or thermal insulation for future hypersonic vehicles such as the National Aerospace Plane (N.A.S.P.). Thermophysical properties for these insulations were also measured including the thermal conductivity at various temperatures and pressures and the emissivity of the fabrics used in the flexible insulations. The thermal response of these materials subjected to aeroconvective heating from a plasma arc is also described. Materials tested included two surface variations of the insulations, and similar insulations coated with a Protective Ceramic Coating (P.C.C.). Surface and backface temperatures were measured in the flexible insulations and on Fibrous Refractory Composite Insulation (F.R.C.I.) used as a calibration model. The uncoated flexible insulations exhibited good thermal performance up to 35 W/sq cm. The use of a P.C.C. to protect these insulations at higher heating rates is described. The results from a computerized thermal analysis model describing thermal response of those materials subjected to the plasma arc conditions are included. Thermal and optical properties were determined including thermal conductivity for the rigid and flexible insulations and emissivity for the insulation fabrics. These properties were utilized to calculate the thermal performance of the rigid and flexible insulations at the maximum heating rate.

Electrochemically Synthesis of Nickel Cobalt Sulfide for High‐Performance Flexible Asymmetric Supercapacitors

PubMed Central

Zhang, Chunyan; Cai, Xiaoyi; Qian, Yao; Jiang, Haifeng; Zhou, Lijun; Li, Baosheng; Shen, Zexiang; Huang, Wei

2017-01-01

Abstract A lightweight, flexible, and highly efficient energy management strategy is highly desirable for flexible electronic devices to meet a rapidly growing demand. Herein, Ni–Co–S nanosheet array is successfully deposited on graphene foam (Ni–Co–S/GF) by a one‐step electrochemical method. The Ni–Co–S/GF composed of Ni–Co–S nanosheet array which is vertically aligned to GF and provides a large interfacial area for redox reactions with optimum interstitials facilitates the ions diffusion. The Ni–Co–S/GF electrodes have high specific capacitance values of 2918 and 2364 F g−1 at current densities of 1 and 20 A g−1, respectively. Using such hierarchical Ni–Co–S/GF as the cathode, a flexible asymmetric supercapacitor (ASC) is further fabricated with polypyrrple(PPy)/GF as the anode. The flexible asymmetric supercapacitors have maximum operation potential window of 1.65 V, and energy densities of 79.3 and 37.7 Wh kg−1 when the power densities are 825.0 and 16100 W kg−1, respectively. It's worth nothing that the ASC cells have robust flexibility with performance well maintained when the devices were bent to different angles from 180° to 15° at a duration of 5 min. The efficient electrochemical deposition method of Ni–Co–S with a preferred orientation of nanosheet arrays is applicable for the flexible energy storage devices. PMID:29610721

Electrochemically Synthesis of Nickel Cobalt Sulfide for High-Performance Flexible Asymmetric Supercapacitors.

PubMed

Zhang, Chunyan; Cai, Xiaoyi; Qian, Yao; Jiang, Haifeng; Zhou, Lijun; Li, Baosheng; Lai, Linfei; Shen, Zexiang; Huang, Wei

2018-02-01

A lightweight, flexible, and highly efficient energy management strategy is highly desirable for flexible electronic devices to meet a rapidly growing demand. Herein, Ni-Co-S nanosheet array is successfully deposited on graphene foam (Ni-Co-S/GF) by a one-step electrochemical method. The Ni-Co-S/GF composed of Ni-Co-S nanosheet array which is vertically aligned to GF and provides a large interfacial area for redox reactions with optimum interstitials facilitates the ions diffusion. The Ni-Co-S/GF electrodes have high specific capacitance values of 2918 and 2364 F g -1 at current densities of 1 and 20 A g -1 , respectively. Using such hierarchical Ni-Co-S/GF as the cathode, a flexible asymmetric supercapacitor (ASC) is further fabricated with polypyrrple(PPy)/GF as the anode. The flexible asymmetric supercapacitors have maximum operation potential window of 1.65 V, and energy densities of 79.3 and 37.7 Wh kg -1 when the power densities are 825.0 and 16100 W kg -1 , respectively. It's worth nothing that the ASC cells have robust flexibility with performance well maintained when the devices were bent to different angles from 180° to 15° at a duration of 5 min. The efficient electrochemical deposition method of Ni-Co-S with a preferred orientation of nanosheet arrays is applicable for the flexible energy storage devices.

Nitrogen doped carbon derived from polyimide/multiwall carbon nanotube composites for high performance flexible all-solid-state supercapacitors

NASA Astrophysics Data System (ADS)

Kim, Dae Kyom; Kim, Nam Dong; Park, Seung-Keun; Seong, Kwang-dong; Hwang, Minsik; You, Nam-Ho; Piao, Yuanzhe

2018-03-01

Flexible all-solid-state supercapacitors are desirable as potential energy storage systems for wearable technologies. Herein, we synthesize aminophenyl multiwall carbon nanotube (AP-MWCNT) grafted polyimide precursor by in situ polymerization method as a nitrogen-doped carbon precursor. Flexible supercapacitor electrodes are fabricated via a coating of carbon precursor on carbon cloth surface and carbonization at high temperature directly. The as-obtained electrodes, which can be directly used without any binders or additives, can deliver a high specific capacitance of 333.4 F g-1 at 1 A g-1 (based on active material mass) and excellent cycle stability with 103% capacitance retention after 10,000 cycles in a three-electrode system. The flexible all-solid-state supercapacitor device exhibits a high volumetric capacitance of 3.88 F cm-3 at a current density of 0.02 mA cm-3. And also the device can deliver a maximum volumetric energy density of 0.50 mWh cm-3 and presents good cycling stability with 85.3% capacitance retention after 10,000 cycles. This device cell can not only show extraordinary mechanical flexibilities allowing folding, twisting, and rolling but also demonstrate remarkable stable electrochemical performances under their forms. This work provides a novel approach to obtain carbon textile-based flexible supercapacitors with high electrochemical performance and mechanical flexibility.

Conducting polymer composite film incorporated with aligned carbon nanotubes for transparent, flexible and efficient supercapacitor

PubMed Central

Lin, Huijuan; Li, Li; Ren, Jing; Cai, Zhenbo; Qiu, Longbin; Yang, Zhibin; Peng, Huisheng

2013-01-01

Polyaniline composite films incorporated with aligned multi-walled carbon nanotubes (MWCNTs) are synthesized through an easy electrodeposition process. These robust and electrically conductive films are found to function as effective electrodes to fabricate transparent and flexible supercapacitors with a maximum specific capacitance of 233 F/g at a current density of 1 A/g. It is 36 times of bare MWCNT sheet, 23 times of pure polyaniline and 3 times of randomly dispersed MWCNT/polyaniline film under the same conditions. The novel supercapacitors also show a high cyclic stability. PMID:23443325

Design and Simulation of Scanner Wrapped by Flexible Microcoil Embedded in Polymer Film for Single-Optical Endoscope Application

NASA Astrophysics Data System (ADS)

Zhao, Mengyuan; Yang, Zhuoqing; Xiang, Xiaojian; Sun, Bin; Ding, Guifu; Zhao, Xiaolin

2018-03-01

A single optic fiber scanner with large scanning angle, based on novel electromagnetic driven, is presented. The cylinder magnet and weight are fixed on the fiber, and vibrate under its second-order frequency by driving racetrack coils on the tube. The flexible driving coil is fabricated by uncomplicated planar MEMS technology on polyimide film, and wrapped on the tube. The electromagnetic and mechanical properties of the endoscope system are studied. Experimental results show that the maximum of the second resonant scanning angle is 9.47°.

Karl von Frisch lecture. Signals and flexibility in the dance communication of honeybees.

PubMed

Michelsen, Axel

2003-03-01

Progress in understanding dance communication in honeybees is reviewed. The behaviour of both dancers and follower bees contain flexible and stereotypic elements. The transfer of specific information about direction and distance probably involves more than one sensory modality. The follower bees need to stay behind the dancer (within the angle of wagging) during at least one waggle run in order to perceive the specific information. Within this zone, a small stationary air-flow receiver (like the antenna of a follower bee) experiences a well-defined maximum when the abdomen of the wagging dancer passes by. Within 1 mm from the tip of the abdomen, the maximum may be caused by oscillating flows generated by the wagging motion. At other positions and distances (up to several millimetres from the dancer) the maximum is due to a spatially narrow jet air flow generated by the vibrating wings. The time pattern of these maxima is a function of the angular position of the receiver relative to the axis of the waggle run and thus a potential cue for direction. In addition to the narrow jet air flows, the dancers can generate a broad jet. The jets are not automatic by-products of wing vibration, since they can be switched on and off when the dancer adjusts the position of her wings.

Facilitated charge transport in ternary interconnected electrodes for flexible supercapacitors with excellent power characteristics

NASA Astrophysics Data System (ADS)

Chen, Wanjun; He, Yongmin; Li, Xiaodong; Zhou, Jinyuan; Zhang, Zhenxing; Zhao, Changhui; Gong, Chengshi; Li, Shuankui; Pan, Xiaojun; Xie, Erqing

2013-11-01

Flexible and high performance supercapacitors are very critical in modern society. In order to develop the flexible supercapacitors with high power density, free-standing and flexible three-dimensional graphene/carbon nanotubes/MnO2 (3DG/CNTs/MnO2) composite electrodes with interconnected ternary 3D structures were fabricated, and the fast electron and ion transport channels were effectively constructed in the rationally designed electrodes. Consequently, the obtained 3DG/CNTs/MnO2 composite electrodes exhibit superior specific capacitance and rate capability compared to 3DG/MnO2 electrodes. Furthermore, the 3DG/CNTs/MnO2 based asymmetric supercapacitor demonstrates the maximum energy and power densities of 33.71 W h kg-1 and up to 22 727.3 W kg-1, respectively. Moreover, the asymmetric supercapacitor exhibits excellent cycling stability with 95.3% of the specific capacitance maintained after 1000 cycle tests. Our proposed synthesis strategy to construct the novel ternary 3D structured electrodes can be efficiently applied to other high performance energy storage/conversion systems.Flexible and high performance supercapacitors are very critical in modern society. In order to develop the flexible supercapacitors with high power density, free-standing and flexible three-dimensional graphene/carbon nanotubes/MnO2 (3DG/CNTs/MnO2) composite electrodes with interconnected ternary 3D structures were fabricated, and the fast electron and ion transport channels were effectively constructed in the rationally designed electrodes. Consequently, the obtained 3DG/CNTs/MnO2 composite electrodes exhibit superior specific capacitance and rate capability compared to 3DG/MnO2 electrodes. Furthermore, the 3DG/CNTs/MnO2 based asymmetric supercapacitor demonstrates the maximum energy and power densities of 33.71 W h kg-1 and up to 22 727.3 W kg-1, respectively. Moreover, the asymmetric supercapacitor exhibits excellent cycling stability with 95.3% of the specific capacitance maintained after 1000 cycle tests. Our proposed synthesis strategy to construct the novel ternary 3D structured electrodes can be efficiently applied to other high performance energy storage/conversion systems. Electronic supplementary information (ESI) available: Additional experimental details; calculations of the specific capacitances, and energy and power densities; additional SEM and optical images; XPS results; additional electrochemical results. See DOI: 10.1039/c3nr03923d

Ionic Liquid Activation of Amorphous Metal-Oxide Semiconductors for Flexible Transparent Electronic Devices

DOE PAGES

Pudasaini, Pushpa Raj; Noh, Joo Hyon; Wong, Anthony T.; ...

2016-02-09

To begin this abstract, amorphous metal-oxide semiconductors offer the high carrier mobilities and excellent large-area uniformity required for high performance, transparent, flexible electronic devices; however, a critical bottleneck to their widespread implementation is the need to activate these materials at high temperatures which are not compatible with flexible polymer substrates. The highly controllable activation of amorphous indium gallium zinc oxide semiconductor channels using ionic liquid gating at room temperature is reported. Activation is controlled by electric field-induced oxygen migration across the ionic liquid-semiconductor interface. In addition to activation of unannealed devices, it is shown that threshold voltages of a transistormore » can be linearly tuned between the enhancement and depletion modes. Finally, the first ever example of transparent flexible thin film metal oxide transistor on a polyamide substrate created using this simple technique is demonstrated. Finally, this study demonstrates the potential of field-induced activation as a promising alternative to traditional postdeposition thermal annealing which opens the door to wide scale implementation into flexible electronic applications.« less

The effect of low versus high approach-motivated positive affect on the balance between maintenance and flexibility.

PubMed

Liu, Liting; Xu, Baihua

2016-05-27

Successful goal-directed behavior in a constantly changing environment requires a balance between maintenance and flexibility. Although some studies have found that positive affect influences this balance differently than neutral affect, one recent study found that motivational intensity of positive affective states influences this balance in a cognitive set-shifting paradigm. However, working memory updating and set shifting are interrelated but distinct components of cognitive control. The present study examined the effect of low versus high approach-motivated positive affect on the balance between maintenance and flexibility in working memory. A simple cuing paradigm (the AX Continuous Performance Task) was employed, and neutral affect and high and low approach-motivated positive affect were induced using affective pictures. The results revealed that, relative to neutral affect, low approach-motivated positive affect attenuated maintenance and increased flexibility, whereas high approach-motivated positive affect promoted maintenance and decreased flexibility. These findings offer further evidence that the effects of positive affect on cognitive control are modulated by approach motivational intensity. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Active-matrix OLED using 150°C a-Si TFT backplane built on flexible plastic substrate

NASA Astrophysics Data System (ADS)

Sarma, Kalluri R.; Chanley, Charles; Dodd, Sonia R.; Roush, Jared; Schmidt, John; Srdanov, Gordana; Stevenson, Matthew; Wessel, Ralf; Innocenzo, Jeffrey; Yu, Gang; O'Regan, Marie B.; MacDonald, W. A.; Eveson, R.; Long, Ke; Gleskova, Helena; Wagner, Sigurd; Sturm, James C.

2003-09-01

Flexible displays fabricated using plastic substrates have a potential for being very thin, light weight, highly rugged with greatly minimized propensity for breakage, roll-to-roll manufacturing and lower cost. The emerging OLED display media offers the advantage of being a solid state and rugged structure for flexible displays in addition to the many potential advantages of an AM OLED over the currently dominant AM LCD. The current high level of interest in flexible displays is facilitating the development of the required enabling technologies which include development of plastic substrates, low temperature active matrix device and backplane fabrication, and display packaging. In the following we will first discuss our development efforts in the PEN based plastic substrates, active matrix backplane technology, low temperature (150°C) a-Si TFT devices and an AM OLED test chip used for evaluating various candidate designs. We will then describe the design, fabrication and successful evaluation and demonstration of a 64x64 pixel AM OLED test display using a-Si TFT backplane fabricated at 150°C on the flexible plastic substrate.

A parameterization method and application in breast tomosynthesis dosimetry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xinhua; Zhang, Da; Liu, Bob

2013-09-15

Purpose: To present a parameterization method based on singular value decomposition (SVD), and to provide analytical parameterization of the mean glandular dose (MGD) conversion factors from eight references for evaluating breast tomosynthesis dose in the Mammography Quality Standards Act (MQSA) protocol and in the UK, European, and IAEA dosimetry protocols.Methods: MGD conversion factor is usually listed in lookup tables for the factors such as beam quality, breast thickness, breast glandularity, and projection angle. The authors analyzed multiple sets of MGD conversion factors from the Hologic Selenia Dimensions quality control manual and seven previous papers. Each data set was parameterized usingmore » a one- to three-dimensional polynomial function of 2–16 terms. Variable substitution was used to improve accuracy. A least-squares fit was conducted using the SVD.Results: The differences between the originally tabulated MGD conversion factors and the results computed using the parameterization algorithms were (a) 0.08%–0.18% on average and 1.31% maximum for the Selenia Dimensions quality control manual, (b) 0.09%–0.66% on average and 2.97% maximum for the published data by Dance et al. [Phys. Med. Biol. 35, 1211–1219 (1990); ibid. 45, 3225–3240 (2000); ibid. 54, 4361–4372 (2009); ibid. 56, 453–471 (2011)], (c) 0.74%–0.99% on average and 3.94% maximum for the published data by Sechopoulos et al. [Med. Phys. 34, 221–232 (2007); J. Appl. Clin. Med. Phys. 9, 161–171 (2008)], and (d) 0.66%–1.33% on average and 2.72% maximum for the published data by Feng and Sechopoulos [Radiology 263, 35–42 (2012)], excluding one sample in (d) that does not follow the trends in the published data table.Conclusions: A flexible parameterization method is presented in this paper, and was applied to breast tomosynthesis dosimetry. The resultant data offer easy and accurate computations of MGD conversion factors for evaluating mean glandular breast dose in the MQSA protocol and in the UK, European, and IAEA dosimetry protocols. Microsoft Excel™ spreadsheets are provided for the convenience of readers.« less

NWEA Professional Learning

ERIC Educational Resources Information Center

Northwest Evaluation Association, 2016

2016-01-01

This comprehensive brochure presents how the Northwest Evaluation Association's professional development offerings--plus flexible delivery options designed for busy lives--can make it easier to utilize data. This brochure explores a range of workshops, coaching, online learning, and professional development packages to meet educators' needs and…

Information Technology.

ERIC Educational Resources Information Center

Reynolds, Roger

1983-01-01

Describes important information-handling products, predicting future devices in light of convergence and greater flexibility offered through use of microchip technology. Contends that information technology and its impact of privacy depends on how information systems are used, arguing that the privacy issue deals more with moral/physiological…

What You Should Know about Single-Ply Roofing.

ERIC Educational Resources Information Center

Szcygiel, Tony L.

1998-01-01

Explains why a single-ply roofing system is the best choice for educational facilities. It discusses how single-ply roofing systems offer flexibility with ease of application; cause less disruption during installation; and are clean, safe, and energy efficient. (GR)

14 CFR 25.1127 - Exhaust driven turbo-superchargers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... flexibility between exhaust conduits and the turbine. (b) There must be provisions for lubricating the turbine and for cooling turbine parts where temperatures are critical. (c) If the normal turbo-supercharger control system malfunctions, the turbine speed may not exceed its maximum allowable value. Except for the...

14 CFR 25.1127 - Exhaust driven turbo-superchargers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... flexibility between exhaust conduits and the turbine. (b) There must be provisions for lubricating the turbine and for cooling turbine parts where temperatures are critical. (c) If the normal turbo-supercharger control system malfunctions, the turbine speed may not exceed its maximum allowable value. Except for the...

14 CFR 25.1127 - Exhaust driven turbo-superchargers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... flexibility between exhaust conduits and the turbine. (b) There must be provisions for lubricating the turbine and for cooling turbine parts where temperatures are critical. (c) If the normal turbo-supercharger control system malfunctions, the turbine speed may not exceed its maximum allowable value. Except for the...

45 CFR 98.1 - Goals and purposes.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND... each State maximum flexibility in developing child care programs and policies that best suit the needs... make their own decisions on the child care that best suits their family's needs; (3) Encourage States...

45 CFR 98.1 - Goals and purposes.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CHILD CARE AND DEVELOPMENT FUND... each State maximum flexibility in developing child care programs and policies that best suit the needs... make their own decisions on the child care that best suits their family's needs; (3) Encourage States...

The organization of domains in proteins obeys Menzerath-Altmann's law of language.

PubMed

Shahzad, Khuram; Mittenthal, Jay E; Caetano-Anollés, Gustavo

2015-08-11

The combination of domains in multidomain proteins enhances their function and structure but lengthens the molecules and increases their cost at cellular level. The dependence of domain length on the number of domains a protein holds was surveyed for a set of 60 proteomes representing free-living organisms from all kingdoms of life. Distributions were fitted using non-linear functions and fitted parameters interpreted with a formulation of decreasing returns. We find that domain length decreases with increasing number of domains in proteins, following the Menzerath-Altmann (MA) law of language. Highly significant negative correlations exist for the set of proteomes examined. Mathematically, the MA law expresses as a power law relationship that unfolds when molecular persistence P is a function of domain accretion. P holds two terms, one reflecting the matter-energy cost of adding domains and extending their length, the other reflecting how domain length and number impinges on information and biophysics. The pattern of diminishing returns can therefore be explained as a frustrated interplay between the strategies of economy, flexibility and robustness, matching previously observed trade-offs in the domain makeup of proteomes. Proteomes of Archaea, Fungi and to a lesser degree Plants show the largest push towards molecular economy, each at their own economic stratum. Fungi increase domain size in single domain proteins while reinforcing the pattern of diminishing returns. In contrast, Metazoa, and to lesser degrees Protista and Bacteria, relax economy. Metazoa achieves maximum flexibility and robustness by harboring compact molecules and complex domain organization, offering a new functional vocabulary for molecular biology. The tendency of parts to decrease their size when systems enlarge is universal for language and music, and now for parts of macromolecules, extending the MA law to natural systems.

A MATLAB toolbox for the efficient estimation of the psychometric function using the updated maximum-likelihood adaptive procedure.

PubMed

Shen, Yi; Dai, Wei; Richards, Virginia M

2015-03-01

A MATLAB toolbox for the efficient estimation of the threshold, slope, and lapse rate of the psychometric function is described. The toolbox enables the efficient implementation of the updated maximum-likelihood (UML) procedure. The toolbox uses an object-oriented architecture for organizing the experimental variables and computational algorithms, which provides experimenters with flexibility in experimental design and data management. Descriptions of the UML procedure and the UML Toolbox are provided, followed by toolbox use examples. Finally, guidelines and recommendations of parameter configurations are given.

Computing Bounds on Resource Levels for Flexible Plans

NASA Technical Reports Server (NTRS)

Muscvettola, Nicola; Rijsman, David

2009-01-01

A new algorithm efficiently computes the tightest exact bound on the levels of resources induced by a flexible activity plan (see figure). Tightness of bounds is extremely important for computations involved in planning because tight bounds can save potentially exponential amounts of search (through early backtracking and detection of solutions), relative to looser bounds. The bound computed by the new algorithm, denoted the resource-level envelope, constitutes the measure of maximum and minimum consumption of resources at any time for all fixed-time schedules in the flexible plan. At each time, the envelope guarantees that there are two fixed-time instantiations one that produces the minimum level and one that produces the maximum level. Therefore, the resource-level envelope is the tightest possible resource-level bound for a flexible plan because any tighter bound would exclude the contribution of at least one fixed-time schedule. If the resource- level envelope can be computed efficiently, one could substitute looser bounds that are currently used in the inner cores of constraint-posting scheduling algorithms, with the potential for great improvements in performance. What is needed to reduce the cost of computation is an algorithm, the measure of complexity of which is no greater than a low-degree polynomial in N (where N is the number of activities). The new algorithm satisfies this need. In this algorithm, the computation of resource-level envelopes is based on a novel combination of (1) the theory of shortest paths in the temporal-constraint network for the flexible plan and (2) the theory of maximum flows for a flow network derived from the temporal and resource constraints. The measure of asymptotic complexity of the algorithm is O(N O(maxflow(N)), where O(x) denotes an amount of computing time or a number of arithmetic operations proportional to a number of the order of x and O(maxflow(N)) is the measure of complexity (and thus of cost) of a maximumflow algorithm applied to an auxiliary flow network of 2N nodes. The algorithm is believed to be efficient in practice; experimental analysis shows the practical cost of maxflow to be as low as O(N1.5). The algorithm could be enhanced following at least two approaches. In the first approach, incremental subalgorithms for the computation of the envelope could be developed. By use of temporal scanning of the events in the temporal network, it may be possible to significantly reduce the size of the networks on which it is necessary to run the maximum-flow subalgorithm, thereby significantly reducing the time required for envelope calculation. In the second approach, the practical effectiveness of resource envelopes in the inner loops of search algorithms could be tested for multi-capacity resource scheduling. This testing would include inner-loop backtracking and termination tests and variable and value-ordering heuristics that exploit the properties of resource envelopes more directly.

From Maximization to Optimization: A Paradigm Shift in Rice Production in Thailand to Improve Overall Quality of Life of Stakeholders

PubMed Central

Doi, Ryoichi; Pitiwut, Supachai

2014-01-01

The concept of crop yield maximization has been widely supported. In practice, however, yield maximization does not necessarily lead to maximum socioeconomic welfare. Optimization is therefore necessary to ensure quality of life of farmers and other stakeholders. In Thailand, a rice farmers' network has adopted a promising agricultural system aimed at the optimization of rice farming. Various feasible techniques were flexibly combined. The new system offers technical strengths and minimizes certain difficulties with which the rice farmers once struggled. It has resulted in fairly good yields of up to 8.75 t ha−1 or yield increases of up to 57% (from 4.38 to 6.88 t ha−1). Under the optimization paradigm, the farmers have established diversified sustainable relationships with the paddy fields in terms of ecosystem management through their own self-motivated scientific observations. The system has resulted in good health conditions for the farmers and villagers, financial security, availability of extra time, and additional opportunities and freedom and hence in the improvement of their overall quality of life. The underlying technical and social mechanisms are discussed herein. PMID:25089294

Enhanced Thermoelectric Properties of Polyaniline Nanofilms Induced by Self-Assembled Supramolecules.

PubMed

Wang, Liming; Yao, Qin; Xiao, Juanxiu; Zeng, Kaiyang; Shi, Wei; Qu, Sanyin; Chen, Lidong

2016-07-05

Polyaniline (PANI) is one of the most promising candidates for flexible organic thermoelectric (TE) applications owing to its relatively low cost and high stability. Herein, the self-assembled supramolecule (SAS) (3,6-dioctyldecyloxy-1,4-benzenedicarboxylic acid) was used as an additive and was introduced into PANI films as a template. Raman spectroscopy, X-ray diffraction, and conductive atomic force microscopy analyses demonstrated that the highly ordered chain structure of PANI was achieved by chemical interactions between PANI and the SAS. Moreover, the ordered regions in the PANI-SAS film increased with a decrease in the film thickness. Consequently, the TE properties of PANI-SAS films were not only much higher than those of PANI films, but they also increased with a decrease in film thickness. The maximum TE power factor of the PANI-SAS film reached 31 μW m(-1)  K(-2) , which is approximately six times higher than the power factor of a PANI film with a similar thickness. This work offers a promising way to prepare PANI thin films with enhanced TE properties. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Simple fiber-optic confocal microscopy with nanoscale depth resolution beyond the diffraction barrier.

PubMed

Ilev, Ilko; Waynant, Ronald; Gannot, Israel; Gandjbakhche, Amir

2007-09-01

A novel fiber-optic confocal approach for ultrahigh depth-resolution (

A high-resolution, confocal laser-scanning microscope and flash photolysis system for physiological studies.

PubMed

Parker, I; Callamaras, N; Wier, W G

1997-06-01

We describe the construction of a high-resolution confocal laser-scanning microscope, and illustrate its use for studying elementary Ca2+ signalling events in cells. An avalanche photodiode module and simple optical path provide a high efficiency system for detection of fluorescence signals, allowing use of a small confocal aperture giving near diffraction-limited spatial resolution (< 300 nm lateral and < 400 nm axial). When operated in line-scan mode, the maximum temporal resolution is 1 ms, and the associated computer software allows complete flexibility to record line-scans continuously for long (minutes) periods or to obtain any desired pixel resolution in x-y scans. An independent UV irradiation system permits simultaneous photolysis of caged compounds over either a uniform, wide field (arc lamp source) or at a tightly focussed spot (frequency-tripled Nd:YAG laser). The microscope thus provides a versatile tool for optical studies of dynamic cellular processes, as well as excellent resolution for morphological studies. The confocal scanner can be added to virtually any inverted microscope for a component cost that is only a small fraction of that of comparable commercial instruments, yet offers better performance and greater versatility.

sideSPIM – selective plane illumination based on a conventional inverted microscope

PubMed Central

Hedde, Per Niklas; Malacrida, Leonel; Ahrar, Siavash; Siryaporn, Albert; Gratton, Enrico

2017-01-01

Previously described selective plane illumination microscopy techniques typically offset ease of use and sample handling for maximum imaging performance or vice versa. Also, to reduce cost and complexity while maximizing flexibility, it is highly desirable to implement light sheet microscopy such that it can be added to a standard research microscope instead of setting up a dedicated system. We devised a new approach termed sideSPIM that provides uncompromised imaging performance and easy sample handling while, at the same time, offering new applications of plane illumination towards fluidics and high throughput 3D imaging of multiple specimen. Based on an inverted epifluorescence microscope, all of the previous functionality is maintained and modifications to the existing system are kept to a minimum. At the same time, our implementation is able to take full advantage of the speed of the employed sCMOS camera and piezo stage to record data at rates of up to 5 stacks/s. Additionally, sample handling is compatible with established methods and switching magnification to change the field of view from single cells to whole organisms does not require labor intensive adjustments of the system. PMID:29026679

Laser scoop desobliteration: a method for minimally invasive remote recanalization of chronically occluded superficial femoral arteries

NASA Astrophysics Data System (ADS)

Heneweer, Carola; Siggelkow, Markus; Helle, Michael; Petzina, Rainer; Wulff, Asmus; Schaefer, Joost P.; Berndt, Rouven; Rusch, Rene; Wedel, Thilo; Klaws, Guenther; Müller-Gerbl, Magdalena; Röcken, Christoph; Jansen, Olav; Lutter, Georg; Cremer, Joachim; Groß, Justus

2015-02-01

Stenosis and occlusion of the superficial femoral artery (SFA) are most common in arterial occlusive disease. There are numerous interventional, surgical, and combined approaches to reconstitute maximum blood supply to the lower limb; however, despite intense clinical research, the long-term success rates are still poor. We present the first results with a catheter prototype for laser-based minimal invasive endarterectomy, called laser scoop desobliteration (LSD). The tip of a glass fiber containing a catheter was modified with a spatula head design and connected to an ultraviolet laser. It was tested in cadavers fixed with the Thiel embalming technique preserving tissue consistency, flexibility, and plasticity. After longitudinal arteriotomy of the SFA, a circular dissection between media and adventitia was performed. Then the LSD catheter was inserted and propagated with a progress of 1 mm/s. Afterward, the atheroma core, which showed a plain surface without substantial attaching tissue debris, was removed. Histological examination of the vessel wall showed that the dissection was performed at the media/adventitia interface. In summary, the constructed LSD catheter allowed a rapid and easy way to perform an endarterectomy, thereby offering an innovative approach in the treatment of chronic occluded SFA.

Examining the 10-Year Rebuilding Dilemma for U.S. Fish Stocks

PubMed Central

Patrick, Wesley S.; Cope, Jason

2014-01-01

Worldwide, fishery managers strive to maintain fish stocks at or above levels that produce maximum sustainable yields, and to rebuild overexploited stocks that can no longer support such yields. In the United States, rebuilding overexploited stocks is a contentious issue, where most stocks are mandated to rebuild in as short a time as possible, and in a time period not to exceed 10 years. Opponents of such mandates and related guidance argue that rebuilding requirements are arbitrary, and create discontinuities in the time and fishing effort allowed for stocks to rebuild due to differences in productivity. Proponents, however, highlight how these mandates and guidance were needed to curtail the continued overexploitation of these stocks by setting firm deadlines on rebuilding. Here we evaluate the statements made by opponents and proponents of the 10-year rebuilding mandate and related guidance to determine whether such points are technically accurate using a simple population dynamics model and a database of U.S. fish stocks to parameterize the model. We also offer solutions to many of the issues surrounding this mandate and its implementation by recommending some fishing mortality based frameworks, which meet the intent of the 10-year rebuilding requirement while also providing more flexibility. PMID:25375788

Near-Infrared to Visible Organic Upconversion Devices Based on Organic Light-Emitting Field Effect Transistors.

PubMed

Li, Dongwei; Hu, Yongsheng; Zhang, Nan; Lv, Ying; Lin, Jie; Guo, Xiaoyang; Fan, Yi; Luo, Jinsong; Liu, Xingyuan

2017-10-18

The near-infrared (NIR) to visible upconversion devices have attracted great attention because of their potential applications in the fields of night vision, medical imaging, and military security. Herein, a novel all-organic upconversion device architecture has been first proposed and developed by incorporating a NIR absorption layer between the carrier transport layer and the emission layer in heterostructured organic light-emitting field effect transistors (OLEFETs). The as-prepared devices show a typical photon-to-photon upconversion efficiency as high as 7% (maximum of 28.7% under low incident NIR power intensity) and millisecond-scale response time, which are the highest upconversion efficiency and one of the fastest response time among organic upconversion devices as referred to the previous reports up to now. The high upconversion performance mainly originates from the gain mechanism of field-effect transistor structures and the unique advantage of OLEFETs to balance between the photodetection and light emission. Meanwhile, the strategy of OLEFETs also offers the advantage of high integration so that no extra OLED is needed in the organic upconversion devices. The results would pave way for low-cost, flexible and portable organic upconversion devices with high efficiency and simplified processing.

Spheroidal models of the exterior gravitational field of Asteroids Bennu and Castalia

NASA Astrophysics Data System (ADS)

Sebera, Josef; Bezděk, Aleš; Pešek, Ivan; Henych, Tomáš

2016-07-01

Gravitational field of small bodies can be modeled e.g. with mascons, a polyhedral model or in terms of harmonic functions. If the shape of a body is close to the spheroid, it is advantageous to employ the spheroidal basis functions for expressing the gravitational field. Spheroidal harmonic models, similarly to the spherical ones, may be used in navigation and geophysical tasks. We focus on modeling the exterior gravitational field of oblate-like Asteroid (101955) Bennu and prolate-like Asteroid (4769) Castalia with spheroidal harmonics. Using the Gauss-Legendre quadrature and the spheroidal basis functions, we converted the gravitational potential of a particular polyhedral model of a constant density into the spheroidal harmonics. The results consist of (i) spheroidal harmonic coefficients of the exterior gravitational field for the Asteroids Bennu and Castalia, (ii) spherical harmonic coefficients for Bennu, and (iii) the first and second-order Cartesian derivatives in the local spheroidal South-East-Up frame for both bodies. The spheroidal harmonics offer biaxial flexibility (compared with spherical harmonics) and low computational costs that allow high-degree expansions (compared with ellipsoidal harmonics). The obtained spheroidal models for Bennu and Castalia represent the exterior gravitational field valid on and outside the Brillouin spheroid but they can be used even under this surface. For Bennu, 5 m above the surface the agreement with point-wise integration was 1% or less, while it was about 10% for Castalia due to its more irregular shape. As the shape models may produce very high frequencies, it was crucial to use higher maximum degree to reduce the aliasing. We have used the maximum degree 360 to achieve 9-10 common digits (in RMS) when reconstructing the input (the gravitational potential) from the spheroidal coefficients. The physically meaningful maximum degree may be lower (≪ 360) but its particular value depends on the distance and/or on the application (navigation, exploration, etc.).

DiscML: an R package for estimating evolutionary rates of discrete characters using maximum likelihood.

PubMed

Kim, Tane; Hao, Weilong

2014-09-27

The study of discrete characters is crucial for the understanding of evolutionary processes. Even though great advances have been made in the analysis of nucleotide sequences, computer programs for non-DNA discrete characters are often dedicated to specific analyses and lack flexibility. Discrete characters often have different transition rate matrices, variable rates among sites and sometimes contain unobservable states. To obtain the ability to accurately estimate a variety of discrete characters, programs with sophisticated methodologies and flexible settings are desired. DiscML performs maximum likelihood estimation for evolutionary rates of discrete characters on a provided phylogeny with the options that correct for unobservable data, rate variations, and unknown prior root probabilities from the empirical data. It gives users options to customize the instantaneous transition rate matrices, or to choose pre-determined matrices from models such as birth-and-death (BD), birth-death-and-innovation (BDI), equal rates (ER), symmetric (SYM), general time-reversible (GTR) and all rates different (ARD). Moreover, we show application examples of DiscML on gene family data and on intron presence/absence data. DiscML was developed as a unified R program for estimating evolutionary rates of discrete characters with no restriction on the number of character states, and with flexibility to use different transition models. DiscML is ideal for the analyses of binary (1s/0s) patterns, multi-gene families, and multistate discrete morphological characteristics.

Performing the Parryscope technique gently for office tubal patency assessment.

PubMed

Parry, J Preston; Riche, Daniel; Rushing, John; Linton, Brittany; Butler, Vicki; Lindheim, Steven R

2017-10-01

To demonstrate a novel approach to office tubal patency assessment through infusing air into saline during flexible office hysteroscopy. We also provide data addressing pain and patient experience relative to hysterosalpingography (HSG). Video presentation of clinical technique with supportive crossover data (Canadian Task Force classification II-1). Its University of Mississippi Medical Center Institutional Review Board protocol number is 2013-0230. Academic hospital. Women undergoing office hysteroscopy and ultrasound, with a subset also having HSG. Air infusion into saline during office hysteroscopy. The focus is on demonstrating how the technique appears and is performed, with supplemental Likert data addressing subjective pain and preference relative to HSG. When performed as described, this office technique has 98.3%-100% sensitivity to tubal occlusion and 83.7% specificity. The gentle technique is central to accurate outcomes, which is facilitated through use of a small-caliber (<3 mm), flexible hysteroscope and avoiding uterine overdistention. Patients are far more likely to report maximum discomfort with HSG. Among patients who also had HSG, 92% somewhat or strongly prefer hysteroscopic assessment. Also, 96% of patients reporting maximum discomfort with HSG had mild to no discomfort with the described technique. Air-infused saline at flexible office hysteroscopy can accurately, gently, and rapidly assess tubal patency. Coupled with strong patient preference for this technique over HSG, it is a promising option for evaluating fertility. NCT02005263. Published by Elsevier Inc.

The dynamics and control of large flexible space structures, part 11

NASA Technical Reports Server (NTRS)

Bainum, Peter M.; Reddy, A. S. S. R; Diarra, Cheick M.; Li, Feiyue

1988-01-01

A mathematical model is developed to predict the dynamics of the proposed Spacecraft Control Laboratory Experiment during the stationkeeping phase. The Shuttle and reflector are assumed to be rigid, while the mass connecting the Shuttle to the reflector is assumed to be flexible with elastic deformations small as compared with its length. It is seen that in the presence of gravity-gradient torques, the system assumes a new equilibrium position primarily due to the offset in the mass attachment point to the reflector from the reflector's mass center. Control is assumed to be provided through the Shuttle's three torquers and throught six actuators located by painrs at two points on the mass and at the reflector mass center. Numerical results confirm the robustness of an LQR derived control strategy during stationkeeping with maximum control efforts significantly below saturation levels. The linear regulator theory is also used to derive control laws for the linearized model of the rigidized SCOLE configuration where the mast flexibility is not included. It is seen that this same type of control strategy can be applied for the rapid single axis slewing of the SCOLE through amplitudes as large as 20 degrees. These results provide a definite trade-off between the slightly larger slewing times with the considerable reduction in over-all control effort as compared with the results of the two point boundary value problem application of Pontryagin's Maximum Principle.

A "Tandem" Strategy to Fabricate Flexible Graphene/Polypyrrole Nanofiber Film Using the Surfactant-Exfoliated Graphene for Supercapacitors.

PubMed

Shu, Kewei; Chao, Yunfeng; Chou, Shulei; Wang, Caiyun; Zheng, Tian; Gambhir, Sanjeev; Wallace, Gordon G

2018-06-19

The surfactant-assisted liquid-phase exfoliation of expanded graphite can produce graphene sheets in large quantities with minimal defects. However, it is difficult to completely remove the surfactant from the final product, thus affecting the electrochemical properties of the produced graphene. In this article, a novel approach to fabricate flexible graphene/polypyrrole film was developed: using surfactant cetyltrimethylammonium bromide as a template for growth of polypyrrole nanofibers (PPyNFs) instead of removal after the exfoliation process; followed by a simple filtration method. The introduction of PPyNF not only increases the electrochemical performance, but also ensures flexibility. This composite film electrode offers a capacitance up to 161 F g -1 along with a capacitance retention rate of over 80% after 5000 cycles.

Flexible medical image management using service-oriented architecture.

PubMed

Shaham, Oded; Melament, Alex; Barak-Corren, Yuval; Kostirev, Igor; Shmueli, Noam; Peres, Yardena

2012-01-01

Management of medical images increasingly involves the need for integration with a variety of information systems. To address this need, we developed Content Management Offering (CMO), a platform for medical image management supporting interoperability through compliance with standards. CMO is based on the principles of service-oriented architecture, implemented with emphasis on three areas: clarity of business process definition, consolidation of service configuration management, and system scalability. Owing to the flexibility of this platform, a small team is able to accommodate requirements of customers varying in scale and in business needs. We describe two deployments of CMO, highlighting the platform's value to customers. CMO represents a flexible approach to medical image management, which can be applied to a variety of information technology challenges in healthcare and life sciences organizations.

Making a successful transition to cash balance. Using employee choice and financial education.

PubMed

Scahill, P; Wiley, P

2000-01-01

As employee work patterns change, the need for flexible plan design has increased. Hybrid plans such as cash balance plans offer a plan design variation that incorporates elements of the traditional defined benefit plan as well as those of defined contribution plans. This article examines plan design trends and discusses both negative and positive reactions to those trends. Finally, the solution of offering choice to plan participants is suggested, and the issues that must be considered are discussed.

The benefits of a work-at-home program.

PubMed

Brownson, Kenneth

2004-01-01

Working from home offers the employee and the organization many benefits. The organization can use telework to recruit and retain valuable employees. The organization can also save money on work space and boost morale and loyalty. Employees enjoy the flexibility and convenience that telework offers. Teleworking is popular in the general business world and can be adapted to some jobs in the health care field. Managers must look throughout their organization to see what jobs can be accomplished either partially or completely at home.

Getting the best return on the employee benefit dollar.

PubMed

Carey, R G; Drachman, D A

1988-12-01

The value of employee benefits depends largely on employees' perceptions of those benefits, rather than on any intrinsic value the benefits have. If employees do not value a benefit highly, the hospital is not getting its money's worth. Hospital management now faces the challenge of reallocating benefit dollars to best meet employees' perceived needs and have the maximum positive impact on employee morale, while holding the line on benefit costs. To meet this challenge, administrators must first determine which benefits employees value the most, with which benefits they are most satisfied, and whether an employee's job category makes a difference. Parkside Associates, Inc., the hospital survey corporation of the Lutheran General Health Care System, Park Ridge, IL, has developed a system for gathering hospital-specific benefit data as part of an employee attitude survey. Employees rate each of their benefits according to (1) the benefit's importance to them and (2) their level of satisfaction with the benefit. Based on the assessment of employees' perceptions of the value and quality of benefits they receive, management can plan one or more strategies for response. For example, hospitals can: 1. Reduce benefits a majority of employees identify as having little importance. 2. Restructure benefits identified as being very important, but which produce little satisfaction. 3. Offer flexible, or "cafeteria," benefit plans so individual employees can increase the level of the benefits they value most and decrease the level of other benefits. 4. Offer educational activities, such as an annual benefits statement, to heighten the employees' awareness of the value of the benefits they are receiving.

48 CFR 13.104 - Promoting competition.

Code of Federal Regulations, 2010 CFR

2010-10-01

... cost of the purchase. (a) The contracting officer must not— (1) Solicit quotations based on personal... practicable competition ordinarily can be obtained by soliciting quotations or offers from sources within the... the maximum extent practicable. Whenever practicable, request quotations or offers from two sources...

Enhanced light out-coupling efficiency of organic light-emitting diodes with an extremely low haze by plasma treated nanoscale corrugation

NASA Astrophysics Data System (ADS)

Hwang, Ju Hyun; Lee, Hyun Jun; Shim, Yong Sub; Park, Cheol Hwee; Jung, Sun-Gyu; Kim, Kyu Nyun; Park, Young Wook; Ju, Byeong-Kwon

2015-01-01

Extremely low-haze light extraction from organic light-emitting diodes (OLEDs) was achieved by utilizing nanoscale corrugation, which was simply fabricated with plasma treatment and sonication. The haze of the nanoscale corrugation for light extraction (NCLE) corresponds to 0.21% for visible wavelengths, which is comparable to that of bare glass. The OLEDs with NCLE showed enhancements of 34.19% in current efficiency and 35.75% in power efficiency. Furthermore, the OLEDs with NCLE exhibited angle-stable electroluminescence (EL) spectra for different viewing angles, with no change in the full width at half maximum (FWHM) and peak wavelength. The flexibility of the polymer used for the NCLE and plasma treatment process indicates that the NCLE can be applied to large and flexible OLED displays.Extremely low-haze light extraction from organic light-emitting diodes (OLEDs) was achieved by utilizing nanoscale corrugation, which was simply fabricated with plasma treatment and sonication. The haze of the nanoscale corrugation for light extraction (NCLE) corresponds to 0.21% for visible wavelengths, which is comparable to that of bare glass. The OLEDs with NCLE showed enhancements of 34.19% in current efficiency and 35.75% in power efficiency. Furthermore, the OLEDs with NCLE exhibited angle-stable electroluminescence (EL) spectra for different viewing angles, with no change in the full width at half maximum (FWHM) and peak wavelength. The flexibility of the polymer used for the NCLE and plasma treatment process indicates that the NCLE can be applied to large and flexible OLED displays. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr06547f

48 CFR 218.170 - Additional acquisition flexibilities.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SYSTEM, DEPARTMENT OF DEFENSE CONTRACTING METHODS AND CONTRACT TYPES EMERGENCY ACQUISITIONS Available... vessels. The contracting officer, without soliciting offers, may issue a written job order for emergency..., Restrictions on food, clothing, fabrics, specialty metals, and hand or measuring tools: (1) Acquisitions at or...

Towards a Flexible Language Lab for Community Colleges.

ERIC Educational Resources Information Center

Conway, Diana

1992-01-01

Suggestions are offered for ways to modify a typical community college language laboratory to serve diverse student needs. The discussion is based on experiences of Anchorage Community College, which modeled its lab on a learning resources center rather than a traditional lab. (LB)

Client-Server: What Is It and Are We There Yet?

ERIC Educational Resources Information Center

Gershenfeld, Nancy

1995-01-01

Discusses client-server architecture in dumb terminals, personal computers, local area networks, and graphical user interfaces. Focuses on functions offered by client personal computers: individualized environments; flexibility in running operating systems; advanced operating system features; multiuser environments; and centralized data…

Biochemistry for Medical Students: A Flexible Student-Oriented Approach. AMEE Case Study No. 3

ERIC Educational Resources Information Center

Macqueen, D.; And Others

1976-01-01

A personalized account of some experiences in the Department of Biochemistry at the University of Dundee during a radical revision of the course for medical students is offered. Innovations of the course are described in detail. (LBH)

Students' Experiences of Learning in a Virtual Classroom

ERIC Educational Resources Information Center

Gedera, Dilani S. P.

2014-01-01

Online learning environments can offer learners opportunities for flexibility, interaction and collaboration distinctly different from face-to-face learning environments. However, the integration of educational technologies also presents challenges and concerns in relation to students' learning. This article attempts to develop a better…

Applications of Microcomputers in Patient Care

PubMed Central

Eden, Henry S.

1979-01-01

This paper serves as an introduction to two sessions on microcomputer applications in patient care. It describes several advantages offered by microcomputers in the design of medical devices--flexibility, reliability, smallness, and low power consumption. It concludes by discussing eight categories of microcomputer application.

Food Service Trends--The Next Two Years and Beyond.

ERIC Educational Resources Information Center

Bowers, R. Steve

1987-01-01

Surveyed college food service trends in various geographical locations in the United States. Discusses the trends, addressing eating alternatives, program issues, flexibility in offerings, nutritional emphasis, management and training changes, concern with costs and profits, updating of physical facilities, marketing, technology, matching…

Psychological Flexibility, ACT, and Organizational Behavior

ERIC Educational Resources Information Center

Bond, Frank W.; Hayes, Steven C.; Barnes-Holmes, Dermot

2006-01-01

This paper offers organizational behavior management (OBM) a behavior analytically consistent way to expand its analysis of, and methods for changing, organizational behavior. It shows how Relational Frame Theory (RFT) suggests that common, problematic, psychological processes emerge from language itself, and they produce psychological…

Providing Better University Personnel through Job Sharing.

ERIC Educational Resources Information Center

Hutton, Clifford E.; McFarlin, Joy Simon

1982-01-01

Universities could benefit by offering more flexible part-time job opportunities such as job-sharing, following an apparent national trend in accommodating social and economic needs. Institutions have many options in scheduling and allocating tasks. Possible benefits include improved employee attitude and productivity. (MSE)

Auxetic materials in design and architecture

NASA Astrophysics Data System (ADS)

Papadopoulou, Athina; Laucks, Jared; Tibbits, Skylar

2017-12-01

Auxetic materials deform in an unusual way when stretched or compressed; they are flexible and adaptable, and, if made from responsive materials, can react to their environment. The opportunities they offer for innovative applications in fashion, design and architecture are just starting to be explored.

Model Legislation: Gifted and Talented.

ERIC Educational Resources Information Center

Foster, Andrew H.; And Others

This report presents a model state legislative bill to provide for the special needs of gifted and talented students. The model bill utilizes a "best practices" framework and attempts to be fiscally responsible and provide maximum flexibility while meeting the needs of gifted and talented students. The model legislation itself begins with a…

40 CFR 63.100 - Applicability and designation of source.

Code of Federal Regulations, 2010 CFR

2010-07-01

... manufacturing process unit has two or more products that have the same maximum annual design capacity on a mass... subject to this subpart. (3) For chemical manufacturing process units that are designed and operated as... chemical manufacturing process units that are designed and operated as flexible operation units shall be...

Universal Teller Curriculum Guide.

ERIC Educational Resources Information Center

DuPage Area Vocational Education Authority, Addison, IL.

This curriculum guide has been designed to provide the teacher with a basis for planning a comprehensive program in the career field of universal teller, and to allow the teacher and learner maximum flexibility. The teaching or instruction, in both educational and financial institutions, can be accomplished through large formal groups, small…

49 CFR 178.1055 - Stacking test.

Code of Federal Regulations, 2014 CFR

2014-10-01

... and no loss of contents during the test or after removal of the test load. ... to a uniformly distributed superimposed test load that is four times the design type maximum gross weight for a period of at least twenty-four hours. (2) For all Flexible Bulk Containers, the load must be...

49 CFR 178.980 - Stacking test.

Code of Federal Regulations, 2012 CFR

2012-10-01

... for transportation and no loss of contents. (2) For flexible Large Packagings, there may be no deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (3) For the... of their capacity and to their maximum net mass, with the load being evenly distributed. (c) Test...

49 CFR 178.980 - Stacking test.

Code of Federal Regulations, 2011 CFR

2011-10-01

... for transportation and no loss of contents. (2) For flexible Large Packagings, there may be no deterioration which renders the Large Packaging unsafe for transportation and no loss of contents. (3) For the... of their capacity and to their maximum net mass, with the load being evenly distributed. (c) Test...

49 CFR 178.1055 - Stacking test.

Code of Federal Regulations, 2013 CFR

2013-10-01

... and no loss of contents during the test or after removal of the test load. ... to a uniformly distributed superimposed test load that is four times the design type maximum gross weight for a period of at least twenty-four hours. (2) For all Flexible Bulk Containers, the load must be...

Marketing and Distributive Education Curriculum Guide in Automotive and Petroleum.

ERIC Educational Resources Information Center

Harris, E. Edward; And Others

This curriculum guide is designed to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of marketing. It also provides marketing and distributive education teachers with maximum flexibility in planning an automotive and petroleum curriculum. The essential common and specialized competencies are…

Marketing and Distributive Education. Wholesaling Curriculum Guide.

ERIC Educational Resources Information Center

Northern Illinois Univ., DeKalb. Dept. of Business Education and Administration Services.

This document is one of four curriculum guides designed to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of marketing as well as to provide marketing and distributive education teachers with maximum flexibility. Introductory information provides directions for using the guide and information on…

Marketing and Distributive Education. Food Marketing Curriculum Guide

ERIC Educational Resources Information Center

Northern Illinois Univ., DeKalb. Dept. of Business Education and Administration Services.

This document is one of four curriculum guides designed to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of marketing as well as to provide marketing and distributive education teachers with maximum flexibility. Introductory information provides directions for using the guide and information on…

Industrial Marketing. Marketing and Distributive Education Curriculum Guide.

ERIC Educational Resources Information Center

Moore, James R.; And Others

This guide is designed to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of marketing as well as to provide marketing and distributive education teacher/coordinators with maximum flexibility in planning an industrial marketing curriculum. The guide was constructed by identifying the competencies…

Marketing Services: Insurance. Marketing and Distributive Education Curriculum Guide.

ERIC Educational Resources Information Center

Luft, Roger L.; And Others

This guide is designed to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of marketing as well as to provide marketing and distributive education teacher/coordinators with maximum flexibility in planning an insurance marketing curriculum. The guide was constructed by identifying the competencies…

Did We Say That? Consumerism and Contract Law.

ERIC Educational Resources Information Center

Nordin, Virginia Davis

1982-01-01

The dominant emerging concept in academic contract theory is that the student-college relationship is not a commercially binding contract but a more flexible quasi-contractual relationship. It allows the university maximum control of the relationship on a continuing basis, allows development of some student rights, and combines traditional and…

Internet MEMS design tools based on component technology

NASA Astrophysics Data System (ADS)

Brueck, Rainer; Schumer, Christian

1999-03-01

The micro electromechanical systems (MEMS) industry in Europe is characterized by small and medium sized enterprises specialized on products to solve problems in specific domains like medicine, automotive sensor technology, etc. In this field of business the technology driven design approach known from micro electronics is not appropriate. Instead each design problem aims at its own, specific technology to be used for the solution. The variety of technologies at hand, like Si-surface, Si-bulk, LIGA, laser, precision engineering requires a huge set of different design tools to be available. No single SME can afford to hold licenses for all these tools. This calls for a new and flexible way of designing, implementing and distributing design software. The Internet provides a flexible manner of offering software access along with methodologies of flexible licensing e.g. on a pay-per-use basis. New communication technologies like ADSL, TV cable of satellites as carriers promise to offer a bandwidth sufficient even for interactive tools with graphical interfaces in the near future. INTERLIDO is an experimental tool suite for process specification and layout verification for lithography based MEMS technologies to be accessed via the Internet. The first version provides a Java implementation even including a graphical editor for process specification. Currently, a new version is brought into operation that is based on JavaBeans component technology. JavaBeans offers the possibility to realize independent interactive design assistants, like a design rule checking assistants, a process consistency checking assistants, a technology definition assistants, a graphical editor assistants, etc. that may reside distributed over the Internet, communicating via Internet protocols. Each potential user thus is able to configure his own dedicated version of a design tool set dedicated to the requirements of the current problem to be solved.

Engineering quadratic nonlinear photonic crystals for frequency conversion of lasers

NASA Astrophysics Data System (ADS)

Chen, Baoqin; Hong, Lihong; Hu, Chenyang; Zhang, Chao; Liu, Rongjuan; Li, Zhiyuan

2018-03-01

Nonlinear frequency conversion offers an effective way to extend the laser wavelength range. Quadratic nonlinear photonic crystals (NPCs) are artificial materials composed of domain-inversion structures whose sign of nonlinear coefficients are modulated with desire to implement quasi-phase matching (QPM) required for nonlinear frequency conversion. These structures can offer various reciprocal lattice vectors (RLVs) to compensate the phase-mismatching during the quadratic nonlinear optical processes, including second-harmonic generation (SHG), sum-frequency generation and the cascaded third-harmonic generation (THG). The modulation pattern of the nonlinear coefficients is flexible, which can be one-dimensional or two-dimensional (2D), be periodic, quasi-periodic, aperiodic, chirped, or super-periodic. As a result, these NPCs offer very flexible QPM scheme to satisfy various nonlinear optics and laser frequency conversion problems via design of the modulation patterns and RLV spectra. In particular, we introduce the electric poling technique for fabricating QPM structures, a simple effective nonlinear coefficient model for efficiently and precisely evaluating the performance of QPM structures, the concept of super-QPM and super-periodically poled lithium niobate for finely tuning nonlinear optical interactions, the design of 2D ellipse QPM NPC structures enabling continuous tunability of SHG in a broad bandwidth by simply changing the transport direction of pump light, and chirped QPM structures that exhibit broadband RLVs and allow for simultaneous radiation of broadband SHG, THG, HHG and thus coherent white laser from a single crystal. All these technical, theoretical, and physical studies on QPM NPCs can help to gain a deeper insight on the mechanisms, approaches, and routes for flexibly controlling the interaction of lasers with various QPM NPCs for high-efficiency frequency conversion and creation of novel lasers.

Flexible, highly efficient all-polymer solar cells

PubMed Central

Kim, Taesu; Kim, Jae-Han; Kang, Tae Eui; Lee, Changyeon; Kang, Hyunbum; Shin, Minkwan; Wang, Cheng; Ma, Biwu; Jeong, Unyong; Kim, Taek-Soo; Kim, Bumjoon J.

2015-01-01

All-polymer solar cells have shown great potential as flexible and portable power generators. These devices should offer good mechanical endurance with high power-conversion efficiency for viability in commercial applications. In this work, we develop highly efficient and mechanically robust all-polymer solar cells that are based on the PBDTTTPD polymer donor and the P(NDI2HD-T) polymer acceptor. These systems exhibit high power-conversion efficiency of 6.64%. Also, the proposed all-polymer solar cells have even better performance than the control polymer-fullerene devices with phenyl-C61-butyric acid methyl ester (PCBM) as the electron acceptor (6.12%). More importantly, our all-polymer solar cells exhibit dramatically enhanced strength and flexibility compared with polymer/PCBM devices, with 60- and 470-fold improvements in elongation at break and toughness, respectively. The superior mechanical properties of all-polymer solar cells afford greater tolerance to severe deformations than conventional polymer-fullerene solar cells, making them much better candidates for applications in flexible and portable devices. PMID:26449658

Catheter-based flexible microcoil RF detectors for internal magnetic resonance imaging

NASA Astrophysics Data System (ADS)

Ahmad, M. M.; Syms, R. R. A.; Young, I. R.; Mathew, B.; Casperz, W.; Taylor-Robinson, S. D.; Wadsworth, C. A.; Gedroyc, W. M. W.

2009-07-01

Flexible catheter probes for magnetic resonance imaging (MRI) of the bile duct are demonstrated. The probes consist of a cytology brush modified to accept a resonant RF detector based on a spiral microcoil and hybrid integrated capacitors, and are designed for insertion into the duct via a non-magnetic endoscope during endoscopic retrograde cholangiopancreatography (ERCP). The coil must be narrow enough (<3 mm) to pass through the biopsy channel of the endoscope and sufficiently flexible to turn through 90° to enter the duct. Coils are fabricated as multi-turn electroplated conductors on a flexible base, and two designs formed on SU-8 and polyimide substrates are compared. It is shown that careful control of thermal load is used to obtain useable mechanical properties from SU-8, and that polyimide/SU-8 composites offer improved mechanical reliability. Good electrical performance is demonstrated and sub-millimetre resolution is obtained in 1H MRI experiments at 1.5 T magnetic field strength using test phantoms and in vitro liver tissue.

Light emitting fabric technologies for photodynamic therapy.

PubMed

Mordon, Serge; Cochrane, Cédric; Tylcz, Jean Baptiste; Betrouni, Nacim; Mortier, Laurent; Koncar, Vladan

2015-03-01

Photodynamic therapy (PDT) is considered to be a promising method for treating various types of cancer. A homogeneous and reproducible illumination during clinical PDT plays a determinant role in preventing under- or over-treatment. The development of flexible light sources would considerably improve the homogeneity of light delivery. The integration of optical fiber into flexible structures could offer an interesting alternative. This paper aims to describe different methods proposed to develop Side Emitting Optical Fibers (SEOF), and how these SEOF can be integrated in a flexible structure to improve light illumination of the skin during PDT. Four main techniques can be described: (i) light blanket integrating side-glowing optical fibers, (ii) light emitting panel composed of SEOF obtained by micro-perforations of the cladding, (iii) embroidery-based light emitting fabric, and (iv) woven-based light emitting fabric. Woven-based light emitting fabrics give the best performances: higher fluence rate, best homogeneity of light delivery, good flexibility. Copyright © 2014 Elsevier B.V. All rights reserved.

Immediate prosthesis over implants retained using abutments with flexible screws: A preliminary study.

PubMed

Peñarrocha-Oltra, David; Serra-Pastor, Blanca; Balaguer-Martí, José-Carlos; Peñarrocha-Diago, Miguel; Agustín-Panadero, Rubén

2017-12-01

Immediate loading protocols for the rehabilitation of edentulous or partially edentulous patients have become very popular, due to the conveniences they afford in comparison with conventional loading techniques. A preliminary study was carried out with 8 patients subjected to dental implant treatment with an immediate loading protocol involving a novel system of abutments with flexible screws. Implant survival was analyzed, together with marginal bone loss and patient and dentist satisfaction. A total of 35 implants were subjected to immediate loading using the abutments with flexible screws. The mean patient and dentist satisfaction score was 9.1 and 8.5, respectively. After 12 months the dental implant survival rate was 95.8%, with a mean marginal bone loss of 0.51 ± 0.12 mm. The novel system of abutments with flexible screws offers a good alternative to conventional immediate loading, since it allows rapid and simple manufacture of a reliable passive fit, fixed interim prosthesis after surgery. Key words: Dental implants, Flexafit®, Immediate loading, Immediate prosthesis.

Flexible Ablators: Applications and Arcjet Testing

NASA Technical Reports Server (NTRS)

Arnold, James O.; Venkatapathy, Ethiraj; Beck, Robin A S.; Mcguire, Kathy; Prabhu, Dinesh K.; Gorbunov, Sergey

2011-01-01

Flexible ablators were conceived in 2009 to meet the technology pull for large, human Mars Exploration Class, 23 m diameter hypersonic inflatable aerodynamic decelerators. As described elsewhere, they have been recently undergoing initial technical readiness (TRL) advancement by NASA. The performance limits of flexible ablators in terms of maximum heat rates, pressure and shear remain to be defined. Further, it is hoped that this emerging technology will vastly expand the capability of future NASA missions involving atmospheric entry systems. This paper considers four topics of relevance to flexible ablators: (1) Their potential applications to near/far term human and robotic missions (2) Brief consideration of the balance between heat shield diameter, flexible ablator performance limits, entry vehicle controllability and aft-body shear layer impingement of interest to designers of very large entry vehicles, (3) The approach for developing bonding processes of flexible ablators for use on rigid entry bodies and (4) Design of large arcjet test articles that will enable the testing of flexible ablators in flight-like, combined environments (heat flux, pressure, shear and structural tensile loading). Based on a review of thermal protection system performance requirements for future entry vehicles, it is concluded that flexible ablators have broad applications to conventional, rigid entry body systems and are enabling to large deployable (both inflatable and mechanical) heat shields. Because of the game-changing nature of flexible ablators, it appears that NASA's Office of the Chief Technologist (OCT) will fund a focused, 3-year TRL advancement of the new materials capable of performance in heat fluxes in the range of 200-600 W/sq. cm. This support will enable the manufacture and use of the large-scale arcjet test designs that will be a key element of this OCT funded activity.

Psychological Flexibility as a Fundamental Aspect of Health

PubMed Central

Kashdan, Todd B.

2010-01-01

Traditionally, positive emotions and thoughts, strengths, and the satisfaction of basic psychological needs for belonging, competence, and autonomy have been seen as the cornerstones of psychological health. Without disputing their importance, these foci fail to capture many of the fluctuating, conflicting forces that are readily apparent when people navigate the environment and social world. In this paper, we review literature to offer evidence for the prominence of psychological flexibility in understanding psychological health. Thus far, the importance of psychological flexibility has been obscured by the isolation and disconnection of research conducted on this topic. Psychological flexibility spans a wide range of human abilities to: recognize and adapt to various situational demands; shift mindsets or behavioral repertoires when these strategies compromise personal or social functioning; maintain balance among important life domains; and be aware, open, and committed to behaviors that are congruent with deeply held values. In many forms of psychopathology, these flexibility processes are absent. In hopes of creating a more coherent understanding, we synthesize work in emotion regulation, mindfulness and acceptance, social and personality psychology, and neuropsychology. Basic research findings provide insight into the nature, correlates, and consequences of psychological flexibility and applied research provides details on promising interventions. Throughout, we emphasize dynamic approaches that might capture this fluid construct in the real-world. PMID:21151705

Materials and Techniques for Implantable Nutrient Sensing Using Flexible Sensors Integrated with Metal-Organic Frameworks.

PubMed

Ling, Wei; Liew, Guoguang; Li, Ya; Hao, Yafeng; Pan, Huizhuo; Wang, Hanjie; Ning, Baoan; Xu, Hang; Huang, Xian

2018-06-01

The combination of novel materials with flexible electronic technology may yield new concepts of flexible electronic devices that effectively detect various biological chemicals to facilitate understanding of biological processes and conduct health monitoring. This paper demonstrates single- or multichannel implantable flexible sensors that are surface modified with conductive metal-organic frameworks (MOFs) such as copper-MOF and cobalt-MOF with large surface area, high porosity, and tunable catalysis capability. The sensors can monitor important nutriments such as ascorbicacid, glycine, l-tryptophan (l-Trp), and glucose with detection resolutions of 14.97, 0.71, 4.14, and 54.60 × 10 -6 m, respectively. In addition, they offer sensing capability even under extreme deformation and complex surrounding environment with continuous monitoring capability for 20 d due to minimized use of biological active chemicals. Experiments using live cells and animals indicate that the MOF-modified sensors are biologically safe to cells, and can detect l-Trp in blood and interstitial fluid. This work represents the first effort in integrating MOFs with flexible sensors to achieve highly specific and sensitive implantable electrochemical detection and may inspire appearance of more flexible electronic devices with enhanced capability in sensing, energy storage, and catalysis using various properties of MOFs. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Flexible copper-indium-diselenide films and devices for space applications

NASA Technical Reports Server (NTRS)

Armstrong, J. H.; Pistole, C. O.; Misra, M. S.; Kapur, V. K.; Basol, B. M.

1991-01-01

With the ever increasing demands on space power systems, it is imperative that low cost, lightweight, reliable photovoltaics be developed. One avenue of pursuit for future space power applications is the use of low cost, lightweight flexible PV cells and arrays. Most work in this area assumes the use of flexible amorphous silicon (a-Si), despite its inherent instability and low efficiencies. However, polycrystalline thin film PV such as copper-indium-diselenide (CIS) are inherently more stable and exhibit better performance than a-Si. Furthermore, preliminary data indicate that CIS also offers exciting properties with respect to space applications. However, CIS has only heretofore only produced on rigid substrates. The implications of flexible CIS upon present and future space power platforms was explored. Results indicate that space qualified CIS can dramatically reduce the cost of PV, and in most cases, can be substituted for silicon (Si) based on end-of-life (EOL) estimations. Furthermore, where cost is a prime consideration, CIS can become cost effective than gallium arsenide (GaAs) in some applications. Second, investigations into thin film deposition on flexible substrates were made, and data from these tests indicate that fabrication of flexible CIS devices is feasible. Finally, data is also presented on preliminary TCO/CdS/CuInSe2/Mo devices.

Is behavioural flexibility evidence of cognitive complexity? How evolution can inform comparative cognition

PubMed Central

Mikhalevich, Irina

2017-01-01

Behavioural flexibility is often treated as the gold standard of evidence for more sophisticated or complex forms of animal cognition, such as planning, metacognition and mindreading. However, the evidential link between behavioural flexibility and complex cognition has not been explicitly or systematically defended. Such a defence is particularly pressing because observed flexible behaviours can frequently be explained by putatively simpler cognitive mechanisms. This leaves complex cognition hypotheses open to ‘deflationary’ challenges that are accorded greater evidential weight precisely because they offer putatively simpler explanations of equal explanatory power. This paper challenges the blanket preference for simpler explanations, and shows that once this preference is dispensed with, and the full spectrum of evidence—including evolutionary, ecological and phylogenetic data—is accorded its proper weight, an argument in support of the prevailing assumption that behavioural flexibility can serve as evidence for complex cognitive mechanisms may begin to take shape. An adaptive model of cognitive-behavioural evolution is proposed, according to which the existence of convergent trait–environment clusters in phylogenetically disparate lineages may serve as evidence for the same trait–environment clusters in other lineages. This, in turn, could permit inferences of cognitive complexity in cases of experimental underdetermination, thereby placing the common view that behavioural flexibility can serve as evidence for complex cognition on firmer grounds. PMID:28479981

Teach Your Computer to Read: Scanners and Optical Character Recognition.

ERIC Educational Resources Information Center

Marsden, Jim

1993-01-01

Desktop scanners can be used with a software technology called optical character recognition (OCR) to convert the text on virtually any paper document into an electronic form. OCR offers educators new flexibility in incorporating text into tests, lesson plans, and other materials. (MLF)

A Second Chance School in Hungary

ERIC Educational Resources Information Center

Limbacher, Laszlo

2008-01-01

Hungary's "Belvarosi Tanoda" Secondary School offers an informal, flexible environment and alternative teaching methods for students who have had problems in other schools. The "Belvarosi Tanoda" (which translates as downtown school) is a second chance school for students who have dropped out of upper secondary education. It…

Multifarenes: new modular cavitands.

PubMed

Parvari, Galit; Annamalai, Senthilmurugan; Borovoi, Iris; Chechik, Helena; Botoshansky, Mark; Pappo, Doron; Keinan, Ehud

2014-03-07

Multifarenes, a new class of macrocycles, which are constructed of alternating building blocks, are conveniently accessible by three complementary syntheses that provide modularity and scalability. In addition to metal-ion coordination, these cavitands show increased flexibility with increasing ring size, offering opportunities for induced fit to guest molecules.

Computerized Manufacturing Automation. Employment, Education, and the Workplace. Summary.

ERIC Educational Resources Information Center

Congress of the U.S., Washington, DC. Office of Technology Assessment.

The application of programmable automation (PA) offers new opportunities to enhance and streamline manufacturing processes. Five PA technologies are examined in this report: computer-aided design, robots, numerically controlled machine tools, flexible manufacturing systems, and computer-integrated manufacturing. Each technology is in a relatively…

A robust and scalable neuromorphic communication system by combining synaptic time multiplexing and MIMO-OFDM.

PubMed

Srinivasa, Narayan; Zhang, Deying; Grigorian, Beayna

2014-03-01

This paper describes a novel architecture for enabling robust and efficient neuromorphic communication. The architecture combines two concepts: 1) synaptic time multiplexing (STM) that trades space for speed of processing to create an intragroup communication approach that is firing rate independent and offers more flexibility in connectivity than cross-bar architectures and 2) a wired multiple input multiple output (MIMO) communication with orthogonal frequency division multiplexing (OFDM) techniques to enable a robust and efficient intergroup communication for neuromorphic systems. The MIMO-OFDM concept for the proposed architecture was analyzed by simulating large-scale spiking neural network architecture. Analysis shows that the neuromorphic system with MIMO-OFDM exhibits robust and efficient communication while operating in real time with a high bit rate. Through combining STM with MIMO-OFDM techniques, the resulting system offers a flexible and scalable connectivity as well as a power and area efficient solution for the implementation of very large-scale spiking neural architectures in hardware.

Adjustment of Part Properties for an Elastomeric Laser Sintering Material

NASA Astrophysics Data System (ADS)

Wegner, A.; Ünlü, T.

2018-03-01

Laser sintering of polymers is gaining more and more importance within the field of small series productions. Polyamide 12 is predominantly used, although a variety of other materials are also available for the laser sintering process. For example, elastomeric, rubberlike materials offer very different part property profiles. Those make the production of flexible parts like, e.g., sealings, flexible tubes or shoe soles possible because they offer high part ductility and low hardness. At the chair for manufacturing technology, a new elastomeric laser sintering material has been developed and then commercialized by a spin-off from university. The aim of the presented study was the analysis of the new material's properties. Proof was found that Shore hardness can be modified by varying the parameter settings. Therefore, the correlation between process parameters, energy input, Shore hardness and other part properties like mechanical properties were analyzed. Based on these results, suitable parameter settings were established which lead to the possibility of producing parts with different Shore hardnesses.

Fabrication and Characterization of Flexible Organic Light Emitting Diodes Based on Transparent Flexible Clay Substrates

NASA Astrophysics Data System (ADS)

Venkatachalam, Shanmugam; Hayashi, Hiromichi; Ebina, Takeo; Nakamura, Takashi; Nanjo, Hiroshi

2013-03-01

In the present work, transparent flexible polymer-doped clay (P-clay) substrates were prepared for flexible organic light emitting diode (OLED) applications. Nanocrystalline indium tin oxide (ITO) thin films were prepared on P-clay substrates by ion-beam sputter deposition method. The structural, optical, and electrical properties of as-prepared ITO/P-clay showed that the as-prepared ITO thin film was amorphous, and the average optical transparency and sheet resistance were around 84% and 56 Ω/square, respectively. The as-prepared ITO/P-clay samples were annealed at 200 and 270 °C for 1 h to improve the optical transparency and electrical conductivity. The average optical transparency was found to be maximum at an annealing temperature of 200 °C. Finally, N,N-bis[(1-naphthyl)-N,N '-diphenyl]-1,1'-biphenyl)-4,4'-diamine (NPB), tris(8-hydroxyquinoline) aluminum (Alq3) thin films, and aluminum (Al) electrode were prepared on ITO/P-clay substrates by thermal evaporation method. The current density-voltage (J-V) characteristic of Al/NPB/ITO/P-clay showed linear Ohmic behaviour. In contrast, J-V characteristic of Al/Alq3/NPB/ITO/P-clay showed non-linear Schottky behaviour. Finally, a very flexible OLED was successfully fabricated on newly fabricated transparent flexible P-clay substrates. The electroluminescence study showed that the emission intensity of light from the flexible OLED device gradually increased with increasing applied voltage.

A Programmable System for Motion Control

NASA Technical Reports Server (NTRS)

Nowlin, Brent C.

2003-01-01

The need for improved flow measurements in the flow path of aeronautics testing facilities has led the NASA Glenn Research Center to develop a new motion control system. The new system is programmable, offering a flexibility unheard of in previous systems. The motion control system is PLC-based, which leads to highly accurate positioning ability, as well as reliability. The user interface is a software-based HMI package, which also adds flexibility to the overall system. The system also has the ability to create and execute motion profiles. This paper discusses the system's operation, control implementation, and experiences.

Printable, flexible and stretchable diamond for thermal management

DOEpatents

Rogers, John A; Kim, Tae Ho; Choi, Won Mook; Kim, Dae Hyeong; Meitl, Matthew; Menard, Etienne; Carlisle, John

2013-06-25

Various heat-sinked components and methods of making heat-sinked components are disclosed where diamond in thermal contact with one or more heat-generating components are capable of dissipating heat, thereby providing thermally-regulated components. Thermally conductive diamond is provided in patterns capable of providing efficient and maximum heat transfer away from components that may be susceptible to damage by elevated temperatures. The devices and methods are used to cool flexible electronics, integrated circuits and other complex electronics that tend to generate significant heat. Also provided are methods of making printable diamond patterns that can be used in a range of devices and device components.

Benefits of 20 kHz PMAD in a nuclear space station

NASA Technical Reports Server (NTRS)

Sundberg, Gale R.

1987-01-01

Compared to existing systems, high frequency ac power provides higher efficiency, lower cost, and improved safety benefits. The 20 kHz power system has exceptional flexibility, is inherently user friendly, and is compatible with all types of energy sources; photovoltaic, solar dynamic, rotating machines and nuclear. A 25 kW, 20 kHz ac power distribution system testbed was recently (1986) developed. The testbed possesses maximum flexibility, versatility, and transparency to user technology while maintaining high efficiency, low mass, and reduced volume. Several aspects of the 20 kHz power management and distribution (PMAD) system that have particular benefits for a nuclear power Space Station are discussed.

Computer aided flexible envelope designs

NASA Technical Reports Server (NTRS)

Resch, R. D.

1975-01-01

Computer aided design methods are presented for the design and construction of strong, lightweight structures which require complex and precise geometric definition. The first, flexible structures, is a unique system of modeling folded plate structures and space frames. It is possible to continuously vary the geometry of a space frame to produce large, clear spans with curvature. The second method deals with developable surfaces, where both folding and bending are explored with the observed constraint of available building materials, and what minimal distortion result in maximum design capability. Alternative inexpensive fabrication techniques are being developed to achieve computer defined enclosures which are extremely lightweight and mathematically highly precise.

Miniaturised medium pressure capillary liquid chromatography system with flexible open platform design using off-the-shelf microfluidic components.

PubMed

Li, Yan; Dvořák, Miloš; Nesterenko, Pavel N; Stanley, Roger; Nuchtavorn, Nantana; Krčmová, Lenka Kujovská; Aufartová, Jana; Macka, Mirek

2015-10-08

Trends towards portable analytical instrumentation of the last decades have not been equally reflected in developments of portable liquid chromatography (LC) instrumentation for rapid on-site measurements. A miniaturised medium pressure capillary LC (MPLC) system with gradient elution capability has been designed based on a flexible modular microfluidic system using primarily off-the-shelf low cost components to ensure wide accessibility to other analysts. The microfluidic platform was assembled on a breadboard and contained microsyringe pumps and switch valves, complemented with an injection valve and on-capillary detectors, all controlled by a PC. Four miniaturised microsyringe pumps, with 5, 20 and 100 μL syringe volume options, formed the basis of the pumping system. Two pairs of pumps were used for each mobile phase to create gradient elution capability. The two microsyringe pumps in each pairs were linked by two electrically operated microfluidic switching valves and both pairs of pumps were connected through a zero void volume cross-connector, thus providing a low hold-up volume for gradient formation. Sample was injected by a 20 nL nano-LC sampling valve, directly connected to a 18 cm long 100 μm i.d. Chromolith CapRod RP-18 monolithic capillary column. On-capillary LED-based UV-vis photometric detection was conducted through a piece of equal diameter fused silica capillary connected after the column. The performance of the portable LC system was evaluated theoretically and experimentally, including the maximum operating pressure, gradient mixing performance, and the performance of the detectors. The 5 μL microsyringe pump offered the best performance, with typical maximum operating pressures up to 11.4 ± 0.4 MPa (water) and gradient pumping repeatability of between 4 and 9% for gradients between 0.10% s(-1) and 0.33% s(-1). Test analytes of charged and uncharged dyes and pharmaceuticals of varying hydrophobicity showed typical RSD values of 0.7-1.4% and 3.3-4.8% in isocratic mode and 1.2-4.6% and 3.2-6.4% in gradient mode, respectively for retention time and peak area repeatability. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

24 CFR 965.505 - Standards for allowances for utilities.

Code of Federal Regulations, 2010 CFR

2010-04-01

... PHA installs air conditioning, it shall provide, to the maximum extent economically feasible, systems... systems that offer each resident the option to choose air conditioning shall include retail meters or... allowances. For systems that offer residents the option to choose air conditioning but cannot be checkmetered...

Few-layer molybdenum disulfide transistors and circuits for high-speed flexible electronics.

PubMed

Cheng, Rui; Jiang, Shan; Chen, Yu; Liu, Yuan; Weiss, Nathan; Cheng, Hung-Chieh; Wu, Hao; Huang, Yu; Duan, Xiangfeng

2014-10-08

Two-dimensional layered materials, such as molybdenum disulfide, are emerging as an exciting material system for future electronics due to their unique electronic properties and atomically thin geometry. Here we report a systematic investigation of MoS2 transistors with optimized contact and device geometry, to achieve self-aligned devices with performance including an intrinsic gain over 30, an intrinsic cut-off frequency fT up to 42 GHz and a maximum oscillation frequency fMAX up to 50 GHz, exceeding the reported values for MoS2 transistors to date (fT~0.9 GHz, fMAX~1 GHz). Our results show that logic inverters or radio frequency amplifiers can be formed by integrating multiple MoS2 transistors on quartz or flexible substrates with voltage gain in the gigahertz regime. This study demonstrates the potential of two-dimensional layered semiconductors for high-speed flexible electronics.

Brief report: glycemic control, quality of life, and school experiences among students with diabetes.

PubMed

Wagner, Julie; Heapy, Alicia; James, Amy; Abbott, Gina

2006-09-01

To investigate the relationships among perceived school experiences, diabetes control, and quality of life (QOL) in children with diabetes. Fifty-eight children with type 1 diabetes and their parents participated. The typical child was 12 years old, had diabetes for 5 years, and attended public, suburban, middle/junior high schools with 300-500 students. Children whose parents reported that school personnel received diabetes training showed significantly better diabetes control than those who reported untrained school personnel. Children who reported their classmates received diabetes training had significantly better QOL than those who reported untrained classmates. Children who reported greater flexibility in performing diabetes care tasks at school had significantly better diabetes control than children who reported less flexibility. Students with diabetes continue to face challenges at school. Training staff and classmates and allowing students the maximum appropriate flexibility in diabetes care appears beneficial for disease control and QOL.

Flexible wearable sensor nodes with solar energy harvesting.

PubMed

Taiyang Wu; Arefin, Md Shamsul; Redoute, Jean-Michel; Yuce, Mehmet Rasit

2017-07-01

Wearable sensor nodes have gained a lot of attention during the past few years as they can monitor and record people's physical parameters in real time. Wearable sensor nodes can promote healthy lifestyles and prevent the occurrence of potential illness or injuries. This paper presents a flexible wearable sensor system powered by an efficient solar energy harvesting technique. It can measure the subject's heartbeats using a photoplethysmography (PPG) sensor and perform activity monitoring using an accelerometer. The solar energy harvester adopts an output current based maximum power point tracking (MPPT) algorithm, which controls the solar panel to operate within its high output power range. The power consumption of the flexible sensor nodes has been investigated under different operation conditions. Experimental results demonstrate that wearable sensor nodes can work for more than 12 hours when they are powered by the solar energy harvester for 3 hours in the bright sunlight.

Few-layer molybdenum disulfide transistors and circuits for high-speed flexible electronics

PubMed Central

Cheng, Rui; Jiang, Shan; Chen, Yu; Liu, Yuan; Weiss, Nathan; Cheng, Hung-Chieh; Wu, Hao; Huang, Yu; Duan, Xiangfeng

2014-01-01

Two-dimensional layered materials, such as molybdenum disulfide, are emerging as an exciting material system for future electronics due to their unique electronic properties and atomically thin geometry. Here we report a systematic investigation of MoS2 transistors with optimized contact and device geometry, to achieve self-aligned devices with performance including an intrinsic gain over 30, an intrinsic cut-off frequency fT up to 42 GHz and a maximum oscillation frequency fMAX up to 50 GHz, exceeding the reported values for MoS2 transistors to date (fT ~ 0.9 GHz, fMAX ~ 1 GHz). Our results show that logic inverters or radio frequency amplifiers can be formed by integrating multiple MoS2 transistors on quartz or flexible substrates with voltage gain in the gigahertz regime. This study demonstrates the potential of two-dimensional layered semiconductors for high-speed flexible electronics. PMID:25295573

Experimental demonstration of active vibration control for flexible structures

NASA Technical Reports Server (NTRS)

Phillips, Douglas J.; Hyland, David C.; Collins, Emmanuel G., Jr.

1990-01-01

Active vibration control of flexible structures for future space missions is addressed. Three experiments that successfully demonstrate control of flexible structures are described. The first is the pendulum experiment. The structure is a 5-m compound pendulum and was designed as an end-to-end test bed for a linear proof mass actuator and its supporting electronics. Experimental results are shown for a maximum-entropy/optimal-projection controller designed to achieve 5 percent damping in the first two pendulum modes. The second experiment was based upon the Harris Multi-Hex prototype experiment (MHPE) apparatus. This is a large optical reflector structure comprising a seven-panel array and supporting truss which typifies a number of generic characteristics of large space systems. The third experiment involved control design and implementation for the ACES structure at NASA Marshall Space Flight Center. The authors conclude with some remarks on the lessons learned from conducting these experiments.

Wearable medical devices using textile and flexible technologies for ambulatory monitoring.

PubMed

Dittmar, Andre; Meffre, Richard; De Oliveira, Fabrice; Gehin, Claudine; Delhomme, Georges

2005-01-01

Health smart clothes are in contact with almost all the surface of the skin offer large possibilities for the location of sensors for non invasive measurements. Head band, collar, tee-shirt, socks, shoes, belts for chest, arm, wrist, legs ... provide localization with specific purpose taking into account their proximity of an organ or a source of biosignal, and also its ergonomic possibility (user friendly) to fix a sensor, and the associated instrumentations (batteries, amplifiers, signal processing, telecom, alarm, display ...). Progress in science and technology offers, for the first time, intelligence, speed, miniaturization, sophistication and new materials at low cost. In this new landscape, microtechnologies, information technologies and telecommunications are a key factor. Microsensors : Microtechnologies offer the possibility of small size, but also intelligent, active device, working with low energy, wireless and non invasive or mini invasive. These sensors have to be thin, flexible and compatible with textile, or made using textile technologies, new fibers with specific properties: mechanical, electrical, optical ... The field of applications is very large, e.g. continuous monitoring on elderly population, professional and military activities, athlete's performance and condition, and people with disabilities. The research are oriented toward two complementary directions: Improving the relevancy of each sensor and increasing the number of sensors for having a more global synthetic and robust information.

The effect of dynamic stretching on hamstrings flexibility with respect to the spino-pelvic rhythm.

PubMed

Hasebe, Kiyotaka; Okubo, Yu; Kaneoka, Koji; Takada, Kohei; Suzuki, Daisuke; Sairyo, Koichi

2016-01-01

To ascertain the dynamic stretch effects of flexibility of the hamstrings on lumbar spine and pelvic kinematics. Tight hamstrings are positively correlated with low back pain. However, it is unclear how flexibility of the hamstrings affects spino-pelvic rhythm. Twelve healthy men participated in the study. The straight leg raising (SLR) angle, finger floor distance (FFD), and spino-pelvic rhythm was measured before and after the 6-week stretching protocol. The forward bending task was divided into 4 phases. The paired t-test was used to determine significant differences before and after the FFD, SLR angle, lumbar motion, and pelvic motion, and spino-pelvic rhythm in each phase (p<0.05). After 6 weeks of stretching, significant improvements were seen in the FFD with maximum forward bending and in the SLR angle. Total pelvic rotation was also significantly increased in contrast to total lumbar flexion. A decreased spino-pelvic ratio was seen in the final phase. Dynamic stretching could change the spino-pelvic rhythm to a pelvis-dominant motion, indicating that flexible hamstrings are important for preventing low back pain.

Engineering cofactor flexibility enhanced 2,3-butanediol production in Escherichia coli.

PubMed

Liang, Keming; Shen, Claire R

2017-12-01

Enzymatic reduction of acetoin into 2,3-butanediol (2,3-BD) typically requires the reduced nicotinamide adenine dinucleotide (NADH) or its phosphate form (NADPH) as electron donor. Efficiency of 2,3-BD biosynthesis, therefore, is heavily influenced by the enzyme specificity and the cofactor availability which varies dynamically. This work describes the engineering of cofactor flexibility for 2,3-BD production by simultaneous overexpression of an NADH-dependent 2,3-BD dehydrogenase from Klebsiella pneumoniae (KpBudC) and an NADPH-specific 2,3-BD dehydrogenase from Clostridium beijerinckii (CbAdh). Co-expression of KpBudC and CbAdh not only enabled condition versatility for 2,3-BD synthesis via flexible utilization of cofactors, but also improved production stereo-specificity of 2,3-BD without accumulation of acetoin. With optimization of medium and fermentation condition, the co-expression strain produced 92 g/L of 2,3-BD in 56 h with 90% stereo-purity for (R,R)-isoform and 85% of maximum theoretical yield. Incorporating cofactor flexibility into the design principle should benefit production of bio-based chemical involving redox reactions.

Hydrodynamics of a three-dimensional self-propelled flexible plate

NASA Astrophysics Data System (ADS)

Ryu, Jaeha; Sung, Hyung Jin

2017-11-01

A three-dimensional self-propelled flexible plate in a quiescent flow was simulated using the immersed boundary method. The clamped leading edge of the flexible plate was forced into a vertical oscillation, while free to move horizontally. To reveal the hydrodynamics of the plate, the averaged cruising speed (UC) , the input power (P) , and the swimming efficiency (η) were analyzed as a function of the bending rigidity (γ) and the flapping frequency (f) . The velocity field around the plate and the exerted force on the plate were demonstrated to find out the dynamic interaction between the plate and the surrounding fluid. The kinematics of the plate, the maximum angle of attack (ϕmax) , and the mean effective length (Leff) were examined accounting for the hydrodynamics of the self-propelled flexible plate. The vortical structures around the plate were visualized, and the influence of the tip vortex on the swimming efficiency was explored qualitatively and quantitatively. This work was supported by the Creative Research Initiatives (No. 2017-013369) program of the National Research Foundation of Korea (MSIP).

Sodium-Doped Mesoporous Ni2P2O7 Hexagonal Tablets for High-Performance Flexible All-Solid-State Hybrid Supercapacitors.

PubMed

Wei, Chengzhen; Cheng, Cheng; Wang, Shanshan; Xu, Yazhou; Wang, Jindi; Pang, Huan

2015-08-01

A simple hydrothermal method has been developed to prepare hexagonal tablet precursors, which are then transformed into porous sodium-doped Ni2P2O7 hexagonal tablets by a simple calcination method. The obtained samples were evaluated as electrode materials for supercapacitors. Electrochemical measurements show that the electrode based on the porous sodium-doped Ni2P2O7 hexagonal tablets exhibits a specific capacitance of 557.7 F g(-1) at a current density of 1.2 A g(-1) . Furthermore, the porous sodium-doped Ni2P2O7 hexagonal tablets were successfully used to construct flexible solid-state hybrid supercapacitors. The device is highly flexible and achieves a maximum energy density of 23.4 Wh kg(-1) and a good cycling stability after 5000 cycles, which confirms that the porous sodium-doped Ni2P2 O7 hexagonal tablets are promising active materials for flexible supercapacitors. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Wearable Solid-State Supercapacitors Operating at High Working Voltage with a Flexible Nanocomposite Electrode.

PubMed

Li, Xiaoyan; Wang, Jun; Zhao, Yaping; Ge, Fengyan; Komarneni, Sridhar; Cai, Zaisheng

2016-10-05

The proposed approach for fabricating ultralight self-sustained electrodes facilitates the structural integration of highly flexible carbon nanofibers, amino-modified multiwalled carbon nanotubes (AM-MWNT), and MnO 2 nanoflakes for potential use in wearable supercapacitors. Because of the higher orientation of AM-MWNT and the sublimation of terephthalic acid (PTA) in the carbonization process, freestanding electrodes could be realized with high porosity and flexibility and could possess remarkable electrochemical properties without using polymer substrates. Wearable symmetric solid-state supercapacitors were further assembled using a LiCl/PVA gel electrolyte, which exhibit a maximum energy density of 44.57 Wh/kg (at a power density of 337.1 W/kg) and a power density of 13330 W/kg (at an energy density of 19.64 Wh/kg) with a working voltage as high as 1.8 V. Due to the combination of several favorable traits such as flexibility, high energy density, and excellent electrochemical cyclability, the presently developed wearable supercapacitors with wide potential windows are expected to be useful for new kinds of portable electric devices.

A flexible tactile-feedback touch screen using transparent ferroelectric polymer film vibrators

NASA Astrophysics Data System (ADS)

Ju, Woo-Eon; Moon, Yong-Ju; Park, Cheon-Ho; Choi, Seung Tae

2014-07-01

To provide tactile feedback on flexible touch screens, transparent relaxor ferroelectric polymer film vibrators were designed and fabricated in this study. The film vibrator can be integrated underneath a transparent cover film or glass, and can also produce acoustic waves that cause a tactile sensation on human fingertips. Poly(vinylidene fluoride-trifluoroethylene-chlorotrifluoroethylene) [P(VDF-TrFE-CTFE)] polymer was used as the relaxor ferroelectric polymer because it produces a large strain under applied electric fields, shows a fast response, and has excellent optical transparency. The natural frequency of this tactile-feedback touch screen was designed to be around 200-240 Hz, at which the haptic perception of human fingertips is the most sensitive; therefore, the resonance of the touch screen at its natural frequency provides maximum haptic sensation. A multilayered relaxor ferroelectric polymer film vibrator was also demonstrated to provide the same vibration power at reduced voltage. The flexible P(VDF-TrFE-CTFE) film vibrators developed in this study are expected to provide tactile sensation not only in large-area flat panel displays, but also in flexible displays and touch screens.

Facilitated charge transport in ternary interconnected electrodes for flexible supercapacitors with excellent power characteristics.

PubMed

Chen, Wanjun; He, Yongmin; Li, Xiaodong; Zhou, Jinyuan; Zhang, Zhenxing; Zhao, Changhui; Gong, Chengshi; Li, Shuankui; Pan, Xiaojun; Xie, Erqing

2013-12-07

Flexible and high performance supercapacitors are very critical in modern society. In order to develop the flexible supercapacitors with high power density, free-standing and flexible three-dimensional graphene/carbon nanotubes/MnO2 (3DG/CNTs/MnO2) composite electrodes with interconnected ternary 3D structures were fabricated, and the fast electron and ion transport channels were effectively constructed in the rationally designed electrodes. Consequently, the obtained 3DG/CNTs/MnO2 composite electrodes exhibit superior specific capacitance and rate capability compared to 3DG/MnO2 electrodes. Furthermore, the 3DG/CNTs/MnO2 based asymmetric supercapacitor demonstrates the maximum energy and power densities of 33.71 W h kg(-1) and up to 22,727.3 W kg(-1), respectively. Moreover, the asymmetric supercapacitor exhibits excellent cycling stability with 95.3% of the specific capacitance maintained after 1000 cycle tests. Our proposed synthesis strategy to construct the novel ternary 3D structured electrodes can be efficiently applied to other high performance energy storage/conversion systems.

Sport-specific trunk muscle profiles in soccer players of different skill levels.

PubMed

Krutsch, Werner; Weishaupt, Philipp; Zeman, Florian; Loibl, Markus; Neumann, Carsten; Nerlich, Michael; Angele, Peter

2015-05-01

Physical fitness and trunk stability are essential factors for successful soccer competition. We investigated the impact of soccer exposure on the trunk muscle profile of players of different skill levels. Professional and amateur soccer players were examined for trunk flexibility and maximum isometric muscle strength in the midseason period 2011. 24 professional soccer players who had not participated in any specific trunk muscle training programmes had significantly higher isometric trunk muscle strength in the sagittal plane (Ext: p = 0.003, Flex: p = 0.014), the frontal plane (Lat. right: p = 0.001, left: p = 0.003) and the transverse plane (Rotation right and left: p < 0.001) than 83 amateur soccer players. Professional players also had higher trunk flexibility in the sagittal plane (Flex: p = 0.001) and the transverse plane (Rotation right: p = 0.02, left: p = 0.002) than amateur players. The side of the dominant kicking leg had no influence on muscle strength and flexibility of the trunk. Trunk flexibility and stability as necessary factors for avoiding physical overstress and injuries are differently trained in player of different soccer skill levels.

Comparison of manual steering and steering via joystick of a flexible rhino endoscope.

PubMed

Eckl, R; Gumprecht, J J; Strauss, G; Hofer, M; Dietz, A; Lueth, T C

2010-01-01

Flexible endoscopes are used in ENT surgery for examination tasks in cases wherever rigid endoscopes are unsuitable to reach certain positions in the nasal cavity. Until today they are steered by hand and no robotized system has been put into clinical practice. One qualification a robot manipulator system has to fulfill to be accepted is not to create new disadvantages compared to the conventional method in surgery. An important factor is the time needed to steer the new system compared to the time needed to steer the conventional system. In this article a robot manipulator system and an experiment are presented to compare the particular times test persons need to perform a certain task. This approach offers the possibility to benchmark the developed robot manipulator system and future systems for flexible rhino endoscopes.

Thin film encapsulation for flexible AM-OLED: a review

NASA Astrophysics Data System (ADS)

Park, Jin-Seong; Chae, Heeyeop; Chung, Ho Kyoon; In Lee, Sang

2011-03-01

Flexible organic light emitting diode (OLED) will be the ultimate display technology to customers and industries in the near future but the challenges are still being unveiled one by one. Thin-film encapsulation (TFE) technology is the most demanding requirement to prevent water and oxygen permeation into flexible OLED devices. As a polymer substrate does not offer the same barrier performance as glass, the TFE should be developed on both the bottom and top side of the device layers for sufficient lifetimes. This work provides a review of promising thin-film barrier technologies as well as the basic gas diffusion background. Topics include the significance of the device structure, permeation rate measurement, proposed permeation mechanism, and thin-film deposition technologies (Vitex system and atomic layer deposition (ALD)/molecular layer deposition (MLD)) for effective barrier films.

Flexible-rate optical packet generation/detection and label swapping for optical label switching networks

NASA Astrophysics Data System (ADS)

Wu, Zhongying; Li, Juhao; Tian, Yu; Ge, Dawei; Zhu, Paikun; Chen, Yuanxiang; Chen, Zhangyuan; He, Yongqi

2017-03-01

In recent years, optical label switching (OLS) gains lots of attentions due to its intrinsic advantages to implement protocol, bit-rate, granularity and data format transparency packet switching. In this paper, we propose a novel scheme to realize flexible-rate optical packet switching for OLS networks. At the transmitter node, flexible-rate packet is generated by parallel modulating different combinations of optical carriers generated from the optical multi-carrier generator (OMCG), among which the low-speed optical label occupies one carrier. At the switching node, label is extracted and re-generated in label processing unit (LPU). The payloads are switched based on routing information and new label is added after switching. At the receiver node, another OMCG serves as local oscillators (LOs) for optical payloads coherent detection. The proposed scheme offers good flexibility for dynamic optical packet switching by adjusting the payload bandwidth and could also effectively reduce the number of lasers, modulators and receivers for packet generation/detection. We present proof-of-concept demonstrations of flexible-rate packet generation/detection and label swapping in 12.5 GHz grid. The influence of crosstalk for cascaded label swapping is also investigated.

Work-life policies for Canadian medical faculty.

PubMed

Gropper, Aaron; Gartke, Kathleen; MacLaren, Monika

2010-09-01

This study aims to catalogue and examine the following work-life flexibility policies at all 17 Canadian medical schools: maternity leave, paternity leave, adoption leave, extension of the probationary period for family responsibilities, part-time faculty appointments, job sharing, and child care. The seven work-life policies of Canadian medical schools were researched using a consistent and systematic method. This method involved an initial web search for policy information, followed by e-mail and telephone contact. The flexibility of the policies was scored 0 (least flexible) to 3 (most flexible). The majority of policies were easily accessible online. Work-life policies were scored out of 3, and average policy scores ranged from 0.47 for job sharing to 2.47 for part-time/work reduction. Across schools, total scores ranged from 7 to 16 out of 21. Variation in scores was noted for parenting leave and child care, whereas minimal variation was noted for other policies. Canadian medical schools are committed to helping medical faculty achieve work-life balance, but improvements can be made in the policies offered at all schools. Improving the quality of work flexibility policies will enhance working conditions and job satisfaction for faculty. This could potentially reduce Canada's loss of talented young academicians.

Engaged Learning through Online Collaborative Public Relations Projects across Universities

ERIC Educational Resources Information Center

Smallwood, Amber M. K.; Brunner, Brigitta R.

2017-01-01

Online learning is complementing and even replacing traditional face-to-face educational models at colleges and universities across the world. Distance education offers pedagogical and resource advantages--flexibility, greater access to education, and increased university revenues. Distance education also presents challenges such as learning to…

Fractals in the Classroom

ERIC Educational Resources Information Center

Fraboni, Michael; Moller, Trisha

2008-01-01

Fractal geometry offers teachers great flexibility: It can be adapted to the level of the audience or to time constraints. Although easily explained, fractal geometry leads to rich and interesting mathematical complexities. In this article, the authors describe fractal geometry, explain the process of iteration, and provide a sample exercise.…

Schools That Sustain: Lessening the Environmental Impact of New Construction.

ERIC Educational Resources Information Center

Peele, Katherine N.; Malone, Sara

2002-01-01

Discusses sustainable school design and its benefits to the environment, offering examples of illustrative schools. Provides suggestions on site selection (such as using smaller sites and recycling existing buildings), sharing facilities with the community, and construction elements that improve environmental impact (such as flexibility,…

Innovation in Course Design

ERIC Educational Resources Information Center

Knipe, Sally

2016-01-01

Initial teacher education programs offered at Australian universities tend to qualify graduates to teach in the age-related contexts of early childhood/primary or secondary, a model that has reflected the organisational evolution of schools. Greater flexibility is required in the design of teacher preparation courses in order to produce graduates…

Web-Based Training. ERIC Digest No. 218.

ERIC Educational Resources Information Center

Brown, Bettina Lankard

Reduced training costs, worldwide accessibility, and improved technological capabilities have made Web-based training (WBT) a viable alternative to classroom instruction. WBT enables businesses to cut their training costs. Efficiency of operation is another major advantage of WBT. The flexibility of time, place, and programs offered via WBT…

The Four-Day Week--What Are the Advantages for Schools?

ERIC Educational Resources Information Center

Richburg, Robert W.; Sjogren, Douglas D.

1983-01-01

Experience in 12 Colorado school districts suggests that implementation of a four-day school week can offer several benefits, including savings in fuel costs, decreased absenteeism, improved efficiency in activity-oriented classes, increased staff development time, and a flexible "fifth day" for extracurricular activities. (PGD)

Campaigning in the Secondary Theater: Challenges for the Operational Commander

DTIC Science & Technology

1987-04-30

threat of German and Ital ian forces staged in the Balkans. Greece, already fighting the Italians, initially refused the British offer of assistance...allowed for tremendous flexibility. This was not the case in the Greek campaign. The operational commander General Maitland Wilson, being appointed late

7 CFR 1717.150 - General.

Code of Federal Regulations, 2010 CFR

2010-01-01

... with the flexibility to negotiate and enter into mergers that offer advantages to the borrowers and to... guarantees. (b) Consistent with prudent lending practices, the maintenance of adequate security for RUS loans.... (d) Since RUS must take action in order to advance funds and otherwise conduct business with a...

Gaining Access to Unemployment Insurance

ERIC Educational Resources Information Center

Stewart, Beverly

2008-01-01

Using contingent faculty gives colleges and universities scheduling flexibility, and the lack of obligation to offer benefits to contingents saves them much money. In this article, the author contends that, in return for this shirking of responsibility, institutions of higher education should provide the merest unemployment insurance benefit to…

Introduction to SmartBooks. Report 23-93.

ERIC Educational Resources Information Center

Kopec, Danny; Wood, Carol

Humankind has become accustomed to reading and learning from printed books. The computer offers us the possibility to exploit another medium whose key advantage is flexibility through extensive memory, computational speed, and versatile representational means. Specifically, we have the hypercard application, an integrated piece of software, with…

Portal Pedagogy: From Interdisciplinarity and Internationalization to Transdisciplinarity and Transnationalization

ERIC Educational Resources Information Center

Monk, Nicholas

2015-01-01

Education in the twenty-first century is characterized by narratives of global connectivity. Opportunities offered by digital technologies, connectivity through mobile platforms, and social media, reinforced by changing expectations of students and parents, have put pressure on universities to reimagine global learning and flexible delivery…

Implementation of Peer-Reviewed Homework Assignments

ERIC Educational Resources Information Center

Zare, Richard N.; Cox, Charles T., Jr.; Murphy, Katherine; Bayas, Camille

2017-01-01

In large, introductory courses, instructors and teaching assistants often struggle to provide detailed feedback on student homework in a timely manner. Here we describe a peer-reviewed homework system that provides quick turnaround while offering flexibility in the construction of homework problems. Homework is administered through a cycle, which…

Teaching with Adolescent Learning in Mind.

ERIC Educational Resources Information Center

Beamon, Glenda Ward

This book offers teachers, through discussion and example, a flexible conceptual framework upon which to base daily decisions about content and pedagogy when teaching adolescents. The Adolescent-Centered Teaching (ACT) models in each chapter are designed as illustrations of this framework. Each ACT further features specific concepts developed…

Revamping California's Education Finance System.

ERIC Educational Resources Information Center

McFadden, Brett

2003-01-01

Describes reasons for California's budget deficits and their impact on school finance. Offers five possible solutions to the school funding crises: Restructure the state's tax and revenue system, restore school district revenue-sharing abilities, initiate a top-to-bottom mandate review, provide greater fiscal and program flexibility, and revamp…

The Ultimate in Flexitime: From Sweden, by Way of Volvo.

ERIC Educational Resources Information Center

Bernstein, Paul

1988-01-01

In the Volvo component plant on Koping, Sweden, an innovative system of multiple shifts and flexible working hours is offered to employees. The system meets the needs of those who are available for work at certain times and helps curtail turnover and absenteeism. (JOW)

49 CFR 178.816 - Topple test.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... For all flexible IBCs, there may be no loss of contents. A slight discharge (e.g., from closures or stitch holes) upon impact is not considered to be a failure, provided no further leakage occurs. [Amdt... must be filled to not less than 95 percent of its capacity and to its maximum net mass, with the load...

A Better Lemon Squeezer? Maximum-Likelihood Regression with Beta-Distributed Dependent Variables

ERIC Educational Resources Information Center

Smithson, Michael; Verkuilen, Jay

2006-01-01

Uncorrectable skew and heteroscedasticity are among the "lemons" of psychological data, yet many important variables naturally exhibit these properties. For scales with a lower and upper bound, a suitable candidate for models is the beta distribution, which is very flexible and models skew quite well. The authors present…

Finance and Credit. Curriculum Guide. Marketing and Distributive Education.

ERIC Educational Resources Information Center

Northern Illinois Univ., DeKalb. Dept. of Business Education and Administration Services.

Designed to be used with the General Marketing Curriculum Guide (ED 156 860), this guide is intended to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of marketing and to allow marketing and distributive education teacher-coordinators maximum flexibility. It contains job competency sheets in ten…

Marketing and Distributive Education. General Retail Merchandising Curriculum Guide.

ERIC Educational Resources Information Center

Northern Illinois Univ., DeKalb. Dept. of Business Education and Administration Services.

This document is one of four curriculum guides designed to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of marketing as well as to provide marketing and distributive education teachers with maximum flexibility. Introductory information provides directions for using the guide and information on…

Marketing and Distributive Education. General Marketing Curriculum Guide.

ERIC Educational Resources Information Center

Northern Illinois Univ., DeKalb. Dept. of Business Education and Administration Services.

This general marketing curriculum guide is the master publication in a series of four curriculum guides. The series is designed to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of marketing as well as to provide marketing and distributive education teachers with maximum flexibility. This guide…

Semiparametric Item Response Functions in the Context of Guessing

ERIC Educational Resources Information Center

Falk, Carl F.; Cai, Li

2016-01-01

We present a logistic function of a monotonic polynomial with a lower asymptote, allowing additional flexibility beyond the three-parameter logistic model. We develop a maximum marginal likelihood-based approach to estimate the item parameters. The new item response model is demonstrated on math assessment data from a state, and a computationally…

Benchmarking performance measurement and lean manufacturing in the rough mill

Treesearch

Dan Cumbo; D. Earl Kline; Matthew S. Bumgardner

2006-01-01

Lean manufacturing represents a set of tools and a stepwise strategy for achieving smooth, predictable product flow, maximum product flexibility, and minimum system waste. While lean manufacturing principles have been successfully applied to some components of the secondary wood products value stream (e.g., moulding, turning, assembly, and finishing), the rough mill is...

Maximizing purchase decision factors other than price.

PubMed

Berkowitz, D A; Diamond, J F; Montagnolo, A J

1992-05-01

Assessing and acquiring technology does not have to be chaotic, driven solely by price, clinical preference, and emotion. With the tools available, it can be distilled to a process of organized common sense, which results in maximum flexibility for the user and allows materiel managers to procure the best, most cost-effective equipment for the hospital.

Marketing and Distributive Education Curriculum Guide. Marketing Services: Real Estate.

ERIC Educational Resources Information Center

Cluck, Janice Bona; Melliges, Pam

This curriculum guide has been designed to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of real estate marketing, as well as to provide the marketing and distributive education teacher/coordinator with maximum flexibility. The essential common and specialized competencies have been identified…

Light-weight robot using piezoelectric motor, sensor and actuator

NASA Astrophysics Data System (ADS)

Wu, Zhen; Bao, Xiao-Qi; Varadan, Vijay K.; Varadan, Vasundara V.

1992-12-01

A prototype single-link, single-axis 'piezorobot' assembled in the laboratory is presented. It basically consists of a flexible arm with the piezoelectric sensors and actuators attached and a servo-controlled piezoelectric motor as the driver. The piezomotor has a diameter of 40 mm, a maximum speed of 520 rpm, and a maximum torque of 0.07 nm, and weighs about 0.07 kg. The 254-mm-long steel arm weighs about 0.0212 kg, including 0.0022 kg of piezoceramic pieces. This piezorobot is controlled by an IBM PC and can move to a programmed destination along a programmed path with quick start and stop responses and a very short settling time. The device's design is shown to be feasible; it has conceptually demonstrated its effectiveness for reducing the self-weight, using flexible linkage while controlling the vibration interferences, and reducing the settling time of a robotic arm. uly/August 1994 1994 7 Springer-Verlag 1994 BF02400853 10.1007/BF02400853 1 Sustainable development and deep ecology: An analysis of competing traditions Forum 477 488 2006 4 5 Springer-Verlag New York Inc 1994 267

Flexible Cryogenic Heat Pipe Development Program

NASA Technical Reports Server (NTRS)

1976-01-01

A heat pipe was designed for operation in the 100 - 200 K temperature range with maximum heat transport as a primary design goal; another designed for operation in the 15 - 100 K temperature range with maximum flexibility as a design goal. Optimum geometry and materials for the container and wicking systems were determined. The high power (100 - 200 K) heat pipe was tested with methane at 100 - 140 K, and test data indicated only partial priming with a performance limit of less than 50 percent of theoretical. A series of tests were conducted with ammonia at approximately 280 K to determine the performance under varying fluid charge and test conditions. The low temperature heat pipe was tested with oxygen at 85 - 95 K and with methanol at 295 - 315 K. Performance of the low temperature heat pipe was below theoretical predictions. Results of the completed testing are presented and possible performance limitation mechanisms are discussed. The lower-than-expected performance was felt to be due to small traces of non-condensible gases which prevented the composite wick from priming.

Variability of the Cyclin-Dependent Kinase 2 Flexibility Without Significant Change in the Initial Conformation of the Protein or Its Environment; a Computational Study.

PubMed

Taghizadeh, Mohammad; Goliaei, Bahram; Madadkar-Sobhani, Armin

2016-06-01

Protein flexibility, which has been referred as a dynamic behavior has various roles in proteins' functions. Furthermore, for some developed tools in bioinformatics, such as protein-protein docking software, considering the protein flexibility, causes a higher degree of accuracy. Through undertaking the present work, we have accomplished the quantification plus analysis of the variations in the human Cyclin Dependent Kinase 2 (hCDK2) protein flexibility without affecting a significant change in its initial environment or the protein per se. The main goal of the present research was to calculate variations in the flexibility for each residue of the hCDK2, analysis of their flexibility variations through clustering, and to investigate the functional aspects of the residues with high flexibility variations. Using Gromacs package (version 4.5.4), three independent molecular dynamics (MD) simulations of the hCDK2 protein (PDB ID: 1HCL) was accomplished with no significant changes in their initial environments, structures, or conformations, followed by Root Mean Square Fluctuations (RMSF) calculation of these MD trajectories. The amount of variations in these three curves of RMSF was calculated using two formulas. More than 50% of the variation in the flexibility (the distance between the maximum and the minimum amount of the RMSF) was found at the region of Val-154. As well, there are other major flexibility fluctuations in other residues. These residues were mostly positioned in the vicinity of the functional residues. The subsequent works were done, as followed by clustering all hCDK2 residues into four groups considering the amount of their variability with respect to flexibility and their position in the RMSF curves. This work has introduced a new class of flexibility aspect of the proteins' residues. It could also help designing and engineering proteins, with introducing a new dynamic aspect of hCDK2, and accordingly, for the other similar globular proteins. In addition, it could provide a better computational calculation of the protein flexibility, which is, especially important in the comparative studies of the proteins' flexibility.

Variability of the Cyclin-Dependent Kinase 2 Flexibility Without Significant Change in the Initial Conformation of the Protein or Its Environment; a Computational Study

PubMed Central

Taghizadeh, Mohammad; Goliaei, Bahram; Madadkar-Sobhani, Armin

2016-01-01

Background Protein flexibility, which has been referred as a dynamic behavior has various roles in proteins’ functions. Furthermore, for some developed tools in bioinformatics, such as protein-protein docking software, considering the protein flexibility, causes a higher degree of accuracy. Through undertaking the present work, we have accomplished the quantification plus analysis of the variations in the human Cyclin Dependent Kinase 2 (hCDK2) protein flexibility without affecting a significant change in its initial environment or the protein per se. Objectives The main goal of the present research was to calculate variations in the flexibility for each residue of the hCDK2, analysis of their flexibility variations through clustering, and to investigate the functional aspects of the residues with high flexibility variations. Materials and Methods Using Gromacs package (version 4.5.4), three independent molecular dynamics (MD) simulations of the hCDK2 protein (PDB ID: 1HCL) was accomplished with no significant changes in their initial environments, structures, or conformations, followed by Root Mean Square Fluctuations (RMSF) calculation of these MD trajectories. The amount of variations in these three curves of RMSF was calculated using two formulas. Results More than 50% of the variation in the flexibility (the distance between the maximum and the minimum amount of the RMSF) was found at the region of Val-154. As well, there are other major flexibility fluctuations in other residues. These residues were mostly positioned in the vicinity of the functional residues. The subsequent works were done, as followed by clustering all hCDK2 residues into four groups considering the amount of their variability with respect to flexibility and their position in the RMSF curves. Conclusions This work has introduced a new class of flexibility aspect of the proteins’ residues. It could also help designing and engineering proteins, with introducing a new dynamic aspect of hCDK2, and accordingly, for the other similar globular proteins. In addition, it could provide a better computational calculation of the protein flexibility, which is, especially important in the comparative studies of the proteins’ flexibility. PMID:28959320

A MATLAB toolbox for the efficient estimation of the psychometric function using the updated maximum-likelihood adaptive procedure

PubMed Central

Richards, V. M.; Dai, W.

2014-01-01

A MATLAB toolbox for the efficient estimation of the threshold, slope, and lapse rate of the psychometric function is described. The toolbox enables the efficient implementation of the updated maximum-likelihood (UML) procedure. The toolbox uses an object-oriented architecture for organizing the experimental variables and computational algorithms, which provides experimenters with flexibility in experimental design and data management. Descriptions of the UML procedure and the UML Toolbox are provided, followed by toolbox use examples. Finally, guidelines and recommendations of parameter configurations are given. PMID:24671826

Spatial-spectral flexible optical networking: enabling switching solutions for a simplified and efficient SDM network platform

NASA Astrophysics Data System (ADS)

Tomkos, I.; Zakynthinos, P.; Klonidis, D.; Marom, D.; Sygletos, S.; Ellis, A.; Salvadori, E.; Siracusa, D.; Angelou, M.; Papastergiou, G.; Psaila, N.; Ferran, J. F.; Ben-Ezra, S.; Jimenez, F.; Fernández-Palacios, J. P.

2013-12-01

The traffic carried by core optical networks grows at a steady but remarkable pace of 30-40% year-over-year. Optical transmissions and networking advancements continue to satisfy the traffic requirements by delivering the content over the network infrastructure in a cost and energy efficient manner. Such core optical networks serve the information traffic demands in a dynamic way, in response to requirements for shifting of traffics demands, both temporally (day/night) and spatially (business district/residential). However as we are approaching fundamental spectral efficiency limits of singlemode fibers, the scientific community is pursuing recently the development of an innovative, all-optical network architecture introducing the spatial degree of freedom when designing/operating future transport networks. Spacedivision- multiplexing through the use of bundled single mode fibers, and/or multi-core fibers and/or few-mode fibers can offer up to 100-fold capacity increase in future optical networks. The EU INSPACE project is working on the development of a complete spatial-spectral flexible optical networking solution, offering the network ultra-high capacity, flexibility and energy efficiency required to meet the challenges of delivering exponentially growing traffic demands in the internet over the next twenty years. In this paper we will present the motivation and main research activities of the INSPACE consortium towards the realization of the overall project solution.

FloWave.US: validated, open-source, and flexible software for ultrasound blood flow analysis.

PubMed

Coolbaugh, Crystal L; Bush, Emily C; Caskey, Charles F; Damon, Bruce M; Towse, Theodore F

2016-10-01

Automated software improves the accuracy and reliability of blood velocity, vessel diameter, blood flow, and shear rate ultrasound measurements, but existing software offers limited flexibility to customize and validate analyses. We developed FloWave.US-open-source software to automate ultrasound blood flow analysis-and demonstrated the validity of its blood velocity (aggregate relative error, 4.32%) and vessel diameter (0.31%) measures with a skeletal muscle ultrasound flow phantom. Compared with a commercial, manual analysis software program, FloWave.US produced equivalent in vivo cardiac cycle time-averaged mean (TAMean) velocities at rest and following a 10-s muscle contraction (mean bias <1 pixel for both conditions). Automated analysis of ultrasound blood flow data was 9.8 times faster than the manual method. Finally, a case study of a lower extremity muscle contraction experiment highlighted the ability of FloWave.US to measure small fluctuations in TAMean velocity, vessel diameter, and mean blood flow at specific time points in the cardiac cycle. In summary, the collective features of our newly designed software-accuracy, reliability, reduced processing time, cost-effectiveness, and flexibility-offer advantages over existing proprietary options. Further, public distribution of FloWave.US allows researchers to easily access and customize code to adapt ultrasound blood flow analysis to a variety of vascular physiology applications. Copyright © 2016 the American Physiological Society.

Mediaprocessors in medical imaging for high performance and flexibility

NASA Astrophysics Data System (ADS)

Managuli, Ravi; Kim, Yongmin

2002-05-01

New high performance programmable processors, called mediaprocessors, have been emerging since the early 1990s for various digital media applications, such as digital TV, set-top boxes, desktop video conferencing, and digital camcorders. Modern mediaprocessors, e.g., TI's TMS320C64x and Hitachi/Equator Technologies MAP-CA, can offer high performance utilizing both instruction-level and data-level parallelism. During this decade, with continued performance improvement and cost reduction, we believe that the mediaprocessors will become a preferred choice in designing imaging and video systems due to their flexibility in incorporating new algorithms and applications via programming and faster-time-to-market. In this paper, we will evaluate the suitability of these mediaprocessors in medical imaging. We will review the core routines of several medical imaging modalities, such as ultrasound and DR, and present how these routines can be mapped to mediaprocessors and their resultant performance. We will analyze the architecture of several leading mediaprocessors. By carefully mapping key imaging routines, such as 2D convolution, unsharp masking, and 2D FFT, to the mediaprocessor, we have been able to achieve comparable (if not better) performance to that of traditional hardwired approaches. Thus, we believe that future medical imaging systems will benefit greatly from these advanced mediaprocessors, offering significantly increased flexibility and adaptability, reducing the time-to-market, and improving the cost/performance ratio compared to the existing systems while meeting the high computing requirements.

A Flexible Statechart-to-Model-Checker Translator

NASA Technical Reports Server (NTRS)

Rouquette, Nicolas; Dunphy, Julia; Feather, Martin S.

2000-01-01

Many current-day software design tools offer some variant of statechart notation for system specification. We, like others, have built an automatic translator from (a subset of) statecharts to a model checker, for use to validate behavioral requirements. Our translator is designed to be flexible. This allows us to quickly adjust the translator to variants of statechart semantics, including problem-specific notational conventions that designers employ. Our system demonstration will be of interest to the following two communities: (1) Potential end-users: Our demonstration will show translation from statecharts created in a commercial UML tool (Rational Rose) to Promela, the input language of Holzmann's model checker SPIN. The translation is accomplished automatically. To accommodate the major variants of statechart semantics, our tool offers user-selectable choices among semantic alternatives. Options for customized semantic variants are also made available. The net result is an easy-to-use tool that operates on a wide range of statechart diagrams to automate the pathway to model-checking input. (2) Other researchers: Our translator embodies, in one tool, ideas and approaches drawn from several sources. Solutions to the major challenges of statechart-to-model-checker translation (e.g., determining which transition(s) will fire, handling of concurrent activities) are retired in a uniform, fully mechanized, setting. The way in which the underlying architecture of the translator itself facilitates flexible and customizable translation will also be evident.

Part-time general surgical training in South Australia: its success and future implications (or: pinnacles, pitfalls and lessons for the future).

PubMed

Neuhaus, Susan; Igras, Emma; Fosh, Beverley; Benson, Sarah

2012-12-01

Flexible training options are sought by an increasing number of Australasian surgical trainees. Reasons include increased participation of women in the surgical workforce, postgraduate training and changing attitudes to family responsibilities. Despite endorsement of flexible training by the Royal Australasian College of Surgeons and Board in General Surgery, part-time (PT) training in General Surgery in Australia and New Zealand is not well established. A permanent 'stand-alone' PT training position was established at the Royal Adelaide Hospital in 2007 under the Surgical Education and Training Program. This position offered 12 months of General Surgical training on a 0.5 full-time (FT) equivalent basis with pro rata emergency and on-call commitments and was accredited for 6 months of General Surgical training. This paper reviews the PT training experience in South Australia. De-identified logbook data were obtained from the South Australian Regional Subcommittee of the Board in General Surgery with consent of each of the trainees. Totals of operative cases were compared against matched FT trainees working on the same unit. Overall, PT trainees achieved comparable operative caseloads compared with their FT colleagues. All trainees included in this review have subsequently passed the Royal Australasian College of Surgeons Fellowship Examination in General Surgery and returned to FT workforce positions. This paper presents two validated models of PT training. Training, resource and regulatory requirements and individual and institutional barriers to flexible training are substantial. Successful PT models offer positive and beneficial training alternatives for General Surgical trainees and contribute to workforce flexibility. © 2012 The Authors. ANZ Journal of Surgery © 2012 Royal Australasian College of Surgeons.

Workplace flexibility: from research to action.

PubMed

Galinsky, Ellen; Sakai, Kelly; Wigton, Tyler

2011-01-01

Ellen Galinsky, Kelly Sakai, and Tyler Wigton explore the "time famine" among American workers-the continuing sense among employees of not having enough time to manage the multiple responsibilities of work and personal and family life. Noting that large shares of U.S. employees report feeling the need for greater workplace flexibility to enable them to take better care of family responsibilities, the authors examine a large-scale community-engagement initiative to increase workplace flexibility voluntarily. Using the 2008 National Study of the Changing Workforce as a primary source of data, the authors begin with an overview of the prevalence of flexibility in today's American workplace. They track which categories of employees have access to various flexibility options, as well as the extent to which employees with access to various types of flexibility use those options. Findings from the study indicate that the majority of employees want flexibility but that access to it varies, with more advantaged employees--those who are well educated, have high salaries, and work full time, for example--being doubly advantaged in having greater access to flexibility. A number of employers, say the authors, tend to be skeptical of the value of workplace flexibility and to fear that employees will abuse it if it is offered. But the study data reveal that most employees use flexibility quite conservatively. When the authors use their nationally representative data set to investigate correlations between access to workplace flexibility and a range of workplace outcomes especially valued by employers--employee engagement, job satisfaction, retention, and health--they find that employers as well as employees can benefit from flexibility. Finally, the authors discuss When Work Works, a large, national community-based initiative under way since 2003 to increase voluntary adoption of workplace flexibility. The authors detail the conceptual basis of the project's design, noting its emphasis on flexibility as one component of effective workplaces that can benefit employers, employees, and communities alike. Galinsky, Sakai, and Wigton conclude by drawing lessons learned from the project and briefly discussing the implications of using research to bring about workplace change.

Effect of Tip-Speed Constraints on the Optimized Design of a Wind Turbine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dykes, K.; Resor, B.; Platt, A.

This study investigates the effect of tip-velocity constraints on system levelized cost of energy (LCOE). The results indicate that a change in maximum tip speed from 80 to 100~m/s could produce a 32% decrease in gearbox weight (a 33% reduction in cost) which would result in an overall reduction of 1%-9% in system LCOE depending on the design approach. Three 100~m/s design cases were considered including a low tip-speed ratio/high-solidity rotor design, a high tip-speed ratio/ low-solidity rotor design, and finally a flexible blade design in which a high tip-speed ratio was used along with removing the tip deflection constraintmore » on the rotor design. In all three cases, the significant reduction in gearbox weight caused by the higher tip-speed and lower overall gear ratio was counterbalanced by increased weights for the rotor and/or other drivetrain components and the tower. As a result, the increased costs of either the rotor or drivetrain components offset the overall reduction in turbine costs from down-sizing the gearbox. Other system costs were not significantly affected, whereas energy production was slightly reduced in the 100~m/s case low tip-speed ratio case and increased in the high tip-speed ratio case. This resulted in system cost of energy reductions moving from the 80~m/s design to the 100~m/s designs of 1.2% for the low tip-speed ratio, 4.6% for the high tip-speed ratio, and 9.5% for the final flexible case (the latter result is optimistic because the impact of deflection of the flexible blade on power production was not modeled). Overall, the results demonstrate that there is a trade-off in system design between the maximum tip velocity and the overall wind plant cost of energy, and there are many trade-offs within the overall system in designing a turbine for a high maximum tip velocity.« less

Astrophysics Source Code Library -- Now even better!

NASA Astrophysics Data System (ADS)

Allen, Alice; Schmidt, Judy; Berriman, Bruce; DuPrie, Kimberly; Hanisch, Robert J.; Mink, Jessica D.; Nemiroff, Robert J.; Shamir, Lior; Shortridge, Keith; Taylor, Mark B.; Teuben, Peter J.; Wallin, John F.

2015-01-01

The Astrophysics Source Code Library (ASCL, ascl.net) is a free online registry of codes used in astronomy research. Indexed by ADS, it now contains nearly 1,000 codes and with recent major changes, is better than ever! The resource has a new infrastructure that offers greater flexibility and functionality for users, including an easier submission process, better browsing, one-click author search, and an RSS feeder for news. The new database structure is easier to maintain and offers new possibilities for collaboration. Come see what we've done!

3D flexible alignment using 2D maximum common substructure: dependence of prediction accuracy on target-reference chemical similarity.

PubMed

Kawabata, Takeshi; Nakamura, Haruki

2014-07-28

A protein-bound conformation of a target molecule can be predicted by aligning the target molecule on the reference molecule obtained from the 3D structure of the compound-protein complex. This strategy is called "similarity-based docking". For this purpose, we develop the flexible alignment program fkcombu, which aligns the target molecule based on atomic correspondences with the reference molecule. The correspondences are obtained by the maximum common substructure (MCS) of 2D chemical structures, using our program kcombu. The prediction performance was evaluated using many target-reference pairs of superimposed ligand 3D structures on the same protein in the PDB, with different ranges of chemical similarity. The details of atomic correspondence largely affected the prediction success. We found that topologically constrained disconnected MCS (TD-MCS) with the simple element-based atomic classification provides the best prediction. The crashing potential energy with the receptor protein improved the performance. We also found that the RMSD between the predicted and correct target conformations significantly correlates with the chemical similarities between target-reference molecules. Generally speaking, if the reference and target compounds have more than 70% chemical similarity, then the average RMSD of 3D conformations is <2.0 Å. We compared the performance with a rigid-body molecular alignment program based on volume-overlap scores (ShaEP). Our MCS-based flexible alignment program performed better than the rigid-body alignment program, especially when the target and reference molecules were sufficiently similar.

Manganese dioxide decoration of macroscopic carbon nanotube fibers: From high-performance liquid-based to all-solid-state supercapacitors

NASA Astrophysics Data System (ADS)

Pendashteh, Afshin; Senokos, Evgeny; Palma, Jesus; Anderson, Marc; Vilatela, Juan J.; Marcilla, Rebeca

2017-12-01

Supercapacitors capable of providing high voltage, energy and power density but yet light, low volume occupying, flexible and mechanically robust are highly interesting and demanded for portable applications. Herein, freestanding flexible hybrid electrodes based on MnO2 nanoparticles grown on macroscopic carbon nanotube fibers (CNTf-MnO2) were fabricated, without the need of any metallic current collector. The CNTf, a support with excellent electrical conductivity, mechanical stability, and appropriate pore structure, was homogeneously decorated with porous akhtenskite ɛ-MnO2 nanoparticles produced via electrodeposition in an optimized organic-aqueous mixture. Electrochemical properties of these decorated fibers were evaluated in different electrolytes including a neutral aqueous solution and a pure 1-butyl-3-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ionic liquid (PYR14TFSI). This comparison helps discriminate the various contributions to the total capacitance: (surface) Faradaic and non-Faradaic processes, improved wetting by aqueous electrolytes. Accordingly, symmetric supercapacitors with PYR14TFSI led to a high specific energy of 36 Wh· kgMnO2-1 (16 Wh·kg-1 including the weight of CNTf) and real specific power of 17 kW· kgMnO2-1 (7.5 kW kg-1) at 3.0 V with excellent cycling stability. Moreover, flexible all solid-state supercapacitors were fabricated using PYR14TFSI-based polymer electrolyte, exhibiting maximum energy density of 21 Wh·kg-1 and maximum power density of 8 kW kg-1 normalized by total active material.

Cowboys and Butterflies: Creative Uses of Spontaneous Fantasy in Career Counseling.

ERIC Educational Resources Information Center

Owen, Dean W., Jr.; Wilson, Jean

1980-01-01

The spontaneous fantasy experiences of students represent a rich source of information that can be creatively structured and used to enhance vocational counseling and career education. The structured sharing and discussion of vocational fantasy offers an enjoyable, flexible method for assessing a wide range of vocational ideas. (Author)

Information retrieval and display system

NASA Technical Reports Server (NTRS)

Groover, J. L.; King, W. L.

1977-01-01

Versatile command-driven data management system offers users, through simplified command language, a means of storing and searching data files, sorting data files into specified orders, performing simple or complex computations, effecting file updates, and printing or displaying output data. Commands are simple to use and flexible enough to meet most data management requirements.

The Politics of Elementary and Secondary Education Act Waivers

ERIC Educational Resources Information Center

Wrabel, Stephani L.; Saultz, Andrew; Polikoff, Morgan S.; McEachin, Andrew; Duque, Matthew

2018-01-01

Executive leadership of the U.S. Department of Education (USDOE) initiated a flexibility offering from No Child Left Behind. Our work explores specific design decisions made in these state-specific accountability systems as associated with state political environments, resources, and demographic characteristics. Our analysis, focused on 42 states…

Students' Views about Potentially Offering Physics Courses Online

ERIC Educational Resources Information Center

Ramlo, Susan E.

2016-01-01

Nationally, many public universities have started to move into the online course and program market that is most often associated with for-profit institutions of higher education. Administrators in public universities make statements regarding benefits to students' desire for flexibility and profit margins related to online courses. But do…

Designing Effective Instruction. 4th Edition.

ERIC Educational Resources Information Center

Morrison, Gary R.; Ross, Steven M.; Kemp, Jerrold E.

This book presents practical skills for successful instructional design. Maintaining a balance between theory and application, it offers a flexible model that can be adapted for use in many settings. Examples are presented from business, higher education, and K-12 education. The 15 chapters are: (1) "Introduction to the Instructional Design…

Designing a Social Environment for Human-Robot Cooperation.

ERIC Educational Resources Information Center

Amram, Fred M.

Noting that work is partly a social activity, and that workers' psychological and emotional needs influence their productivity, this paper explores avenues for improving human-robot cooperation and for enhancing worker satisfaction in the environment of flexible automation. The first section of the paper offers a brief overview of the…

Offering a Framework for Value Co-Creation in Virtual Academic Learning Environments

ERIC Educational Resources Information Center

Ranjbarfard, Mina; Heidari Sureshjani, Mahboobeh

2018-01-01

Purpose: This research aims to convert the traditional teacher-student models, in which teachers determine the learning resources, into a flexible structure and an active learning environment so that students can participate in the educational processes and value co-creation in virtual academic learning environments (VALEs).…

Laser frequency stabilization using a transfer interferometer

NASA Astrophysics Data System (ADS)

Jackson, Shira; Sawaoka, Hiromitsu; Bhatt, Nishant; Potnis, Shreyas; Vutha, Amar C.

2018-03-01

We present a laser frequency stabilization system that uses a transfer interferometer to stabilize slave lasers to a reference laser. Our implementation uses off-the-shelf optical components along with microcontroller-based digital feedback, and offers a simple, flexible, and robust way to stabilize multiple laser frequencies to better than 1 MHz.

A Multimodal Analysis of Lexical Explanation Sequences in Webconferencing-Supported Language Teaching

ERIC Educational Resources Information Center

Wigham, Ciara R.

2017-01-01

Higher education institutions are increasingly interested in offering more flexible teaching and learning delivery methods that are often independent of place. Where foreign language learning is concerned, telecollaboration is gaining ground. This paper focuses on synchronous webconferencing-supported teaching and examines how different semiotic…

Active optical cable for intrasatellite communications

NASA Astrophysics Data System (ADS)

Blasco, J.; Cano, D.; Navasquillo, O.; Esteban, M. A.

2017-11-01

DAS Photonics and Airbus Defence and Space (Spain) have been working for more than six years in the concept of an Active Optical Cable (AOC) for copper cable substitution. The main advantages that AOC offers are significant mass and size saving, better flexibility and routing of the cable and immunity to EMI.

Asynchronous Assessment in a Large Lecture Marketing Course

ERIC Educational Resources Information Center

Downey, W. Scott; Schetzsle, Stacey

2012-01-01

Asynchronous assessment, which includes quizzes or exams online or outside class, offers marketing educators an opportunity to make more efficient use of class time and to enhance students' learning experiences by giving them more flexibility and choice in their assessment environment. In this paper, we examine the performance difference between…

Excess Benefit Plans and Other Nonqualified Deferred Compensation Palns Under ERISA

ERIC Educational Resources Information Center

Vogel, Mark A.

1977-01-01

The benefits of and restrictions imposed on qualified pension and profit-sharing plans are discussed in terms of Excess Benefit Plans (EPB), a type of deferred compensation plan. EPBs and unfunded deferred compensation plans offer flexible methods of providing additional benefits for executives and key employees. (LBH)

Acceptance and Commitment Therapy (ACT): An Overview for Practitioners

ERIC Educational Resources Information Center

Bowden, Tim; Bowden, Sandra

2012-01-01

Acceptance and Commitment Therapy (ACT) offers school counsellors a practical and meaningful approach to helping students deal with a range of issues. This is achieved through encouraging psychological flexibility through the application of six key principles. This article describes our introduction to ACT, ACT's application to children and…

Stochastic and Historical Resonances of the Unit in Physics and Psychometrics

ERIC Educational Resources Information Center

Fisher, William P., Jr.

2011-01-01

Humphry's article, "The Role of the Unit in Physics and Psychometrics," offers fundamental clarifications of measurement concepts that Fisher hopes will find a wide audience. In particular, parameterizing discrimination while preserving statistical sufficiency will indeed provide greater flexibility in accounting "for the effects of empirical…

Incorporating Technologies into a Flexible Teaching Space

ERIC Educational Resources Information Center

Joy, Mike; Foss, Jonathan; King, Emma; Sinclair, Jane; Sitthiworachart, Jirarat; Davis, Rachel

2014-01-01

Higher education institutions are increasingly exploring how they can use emerging technologies to develop and enhance the learning experiences offered to students. These activities have mainly focused on developing student-centered facilities. The University of Warwick has taken the next step by developing a space (the Teaching Grid) specifically…

From SCORM to Common Cartridge: A Step Forward

ERIC Educational Resources Information Center

Gonzalez-Barbone, Victor; Anido-Rifon, Luis

2010-01-01

Shareable Content Object Reference Model (SCORM) was proposed as a standard for sharable learning object packaging, delivering and sequencing. Several years later, Common Cartridge (CC) is proposed as an enhancement of SCORM offering more flexibility and addressing needs not originally envisioned, namely assessment and web 2.0 standards, content…

"Special Delivery": Case Studies in Alternative Teacher Licensure Programs for Students of Color.

ERIC Educational Resources Information Center

Hasslen, Robin; Green, Les

St. Cloud State University's Teacher of Color project provides alternate licensure for degreed individuals needing only to complete their teacher education core and subject area coursework. It offers minority students on- and off-campus programs, financial support, flexible hours, and a compressed program. Researchers examined participating…

Accountability Issues to Watch under NCLB Waivers

ERIC Educational Resources Information Center

Kober, Nancy; Riddle, Wayne

2012-01-01

In September 2011, the Obama Administration invited states to apply for waivers of key requirements of the Elementary and Secondary Education Act (ESEA) as amended by the No Child Left Behind Act (NCLB). The Administration's waiver initiative offers states the flexibility to move away from the flawed provisions of NCLB, including several…

Number of Single-Sex Schools Growing

ERIC Educational Resources Information Center

Barak, Tal

2004-01-01

The U.S. Department of Education's office for civil rights has proposed amending the regulations governing Title IX of the Education Amendments of 1972--which prohibits sex discrimination in programs that receive federal money--to allow more flexibility in offering single-sex schools or classes. This article discusses the rapid growth of…

77 FR 38769 - 97th Annual Meeting of the National Conference on Weights and Measures

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-29

... testing equipment that comprise the regulatory control of commercial weighing and measuring devices. The... specifications to recognize current marketing practices of offering pre or post delivery discounts on fuel prices... proposal would allow device manufacturers greater flexibility in the design and operation of customer...

Enhancing Computer-Based Lessons for Effective Speech Education.

ERIC Educational Resources Information Center

Hemphill, Michael R.; Standerfer, Christina C.

1987-01-01

Assesses the advantages of computer-based instruction on speech education. Concludes that, while it offers tremendous flexibility to the instructor--especially in dynamic lesson design, feedback, graphics, and artificial intelligence--there is no inherent advantage to the use of computer technology in the classroom, unless the student interacts…

Resiliency Techniques in School Practice

ERIC Educational Resources Information Center

Molony, Terry; Henwood, Maureen; Gilroy, Shawn

2010-01-01

School psychologists can help build resilience in youth in many ways. This article offers a list of some easy techniques to use when working with individuals or groups, most based on basic cognitive-behavior therapy (CBT) techniques. They include: (1) Emotional awareness; (2) Emotional Regulation; (3) Cognitive Flexibility; (4) Self-efficacy; and…

Advancing Measurement of Work and Family Domain Boundary Characteristics

ERIC Educational Resources Information Center

Matthews, Russell A.; Barnes-Farrell, Janet L.; Bulger, Carrie A.

2010-01-01

Recent research offers promising theoretical frameworks for thinking about the work-family interface in terms of the boundaries individuals develop around work and family. However, measures for important constructs proposed by these theories are needed. Using two independent samples, we report on the refinement of existing "boundary flexibility"…

An Evaluation of Student Outcomes by Course Duration in Online Higher Education

ERIC Educational Resources Information Center

Shaw, Melanie; Chametzky, Barry; Burrus, Scott W.; Walters, Kelley J.

2013-01-01

To facilitate student learning and ensure financial stability, leaders in higher education institutions offering online degrees and programs are adopting flexible course schedules with shorter terms. The literature does not include many evaluations demonstrating how shorter duration terms and courses might affect student achievement. In this…

Post-Implementation Insights about a Hybrid Degree Program

ERIC Educational Resources Information Center

Toth, Meredith; Foulger, Teresa S.; Amrein-Beardsley, Audrey

2008-01-01

Researchers and practitioners in the field of online learning continue to debate how to best leverage the convenience of online delivery while maintaining or increasing the quality and effectiveness of course content and delivery. While students demand the flexibility and convenience that distance education offerings provide, instructors and…

Teacher Perceptions of Learner-Learner Engagement at a Cyber High School

ERIC Educational Resources Information Center

Borup, Jered

2016-01-01

Distance education has historically contained little or no learner-learner interactions. Currently the Internet allows for unprecedented levels of learner-learner interaction and has the potential to transform how students learn online. However, many courses offered online focus more on flexibility and independence than on interaction and…

A Thematic Instruction Approach to Teaching Technology and Engineering

ERIC Educational Resources Information Center

Moyer, Courtney D.

2016-01-01

Thematic instruction offers flexible opportunities to engage students with real-world experiences in the technology and engineering community. Whether used in a broad unifying theme or specific project-based theme, research has proven that thematic instruction has the capacity to link cross-curricular subjects, facilitate active learning, and…

Grow Creativity!

ERIC Educational Resources Information Center

Shively, Candace Hackett

2011-01-01

Creativity matters. A shared vocabulary and lens for creativity helps teachers and students know what it means to "be creative" and where to start. J. P. Guilford's FFOE model of divergent thinking from the 1950s offers four dimensions to describe creativity: (1) Fluency; (2) Flexibility; (3) Originality; and (4) Elaboration. FFOE makes time spent…

The Words in My Pencil: Considering Children's Writing.

ERIC Educational Resources Information Center

Martin, Anne

Methods of eliciting writing from children are explored in this monograph, which includes samples of nine- and ten-year-old students' writing. The monograph offers four recommendations for improving writing skills: make writing a daily activity; take children's writing seriously; maintain flexible standards of form and language; and identify group…

Hybrid Teaching in Extension: Learning at the Crossroads

ERIC Educational Resources Information Center

Hino, Jeff; Kahn, Cub

2016-01-01

Extension clients' learning preferences are changing, with many increasingly going online for educational content. In response, Oregon State University Extension pilot tested a training program for Extension educators to explore hybrid teaching--a methodology that could provide more flexible access to a wider audience. Hybrid teaching offers a…

"A Virtually Limitless Resource"

ERIC Educational Resources Information Center

Stanistreet, Paul

2008-01-01

With skills such as flexibility and originality increasingly required by an economy struggling to adapt to sudden and seismic change, there is renewed interest in what engagement in culture and creativity can offer. This author discovered that the difference such engagement can make to people's lives has long been recognised at Morley College.…

Errors of Inference in Structural Equation Modeling

ERIC Educational Resources Information Center

McCoach, D. Betsy; Black, Anne C.; O'Connell, Ann A.

2007-01-01

Although structural equation modeling (SEM) is one of the most comprehensive and flexible approaches to data analysis currently available, it is nonetheless prone to researcher misuse and misconceptions. This article offers a brief overview of the unique capabilities of SEM and discusses common sources of user error in drawing conclusions from…

Federal Student Loan Programs

ERIC Educational Resources Information Center

Federal Student Aid, US Department of Education, 2014

2014-01-01

For those needing a loan to attend college, think federal aid first. Federal student loans usually offer borrowers lower interest rates and have more flexible repayment terms and options than private student loans. This brief report answers the following questions about federal aid: (1) What is a federal student loan?; (2) What is a private…

Connecting Information Literacy and Social Justice: Why and How

ERIC Educational Resources Information Center

Saunders, Laura

2017-01-01

Libraries have a long, though not uncomplicated, history with social justice and social advocacy. The new ACRL "Framework for Information Literacy," which is more conceptual and flexible than the original Standards, offers an opportunity for librarians to approach teaching and learning from a social justice perspective. Indeed, the…

Learner-Focused Evaluation Cycles: Facilitating Learning Using Feedforward, Concurrent and Feedback Evaluation

ERIC Educational Resources Information Center

Cathcart, Abby; Greer, Dominique; Neale, Larry

2014-01-01

There is a growing trend to offer students learning opportunities that are flexible, innovative and engaging. As educators embrace student-centred agile teaching and learning methodologies, which require continuous reflection and adaptation, the need to evaluate students' learning in a timely manner has become more pressing. Conventional…

"Breaking Ranks" in Action: Flexibility Required

ERIC Educational Resources Information Center

Hartzman, Marlene; Mero, Dianne

2011-01-01

Much like the MetLife Foundation-NASSP Breakthrough Schools that came before them, the honoree schools this year are remarkable. In addition to offering students safe and challenging learning environments, the schools also afford their adult members a respectful, collaborative place to work and grow, and they give their diverse communities an…

Stretching & Flexibility: An Interactive Encyclopedia of Stretching. [CD-ROM].

ERIC Educational Resources Information Center

2002

This CD-ROM offers 140 different stretches in full-motion video sequences. It focuses on the proper techniques for overall physical fitness, injury prevention and rehabilitation, and 23 different sports (e.g., golf, running, soccer, skiing, climbing, football, and baseball). Topics include stretching for sports; stretching awareness and education…

Iowa Department of Education Guidelines for PK-12 Competency-Based Pathways

ERIC Educational Resources Information Center

Iowa Department of Education, 2013

2013-01-01

This document provides guidelines for developing competency-based pathways in Iowa districts and schools and outlines waiver requirements and procedures. Competency-based pathways provide ways to validate learning of standards that occurs outside the structure of the traditional school and offer flexibility for schools to engage students in…

Reframing Language Allocation Policy in Dual Language Bilingual Education

ERIC Educational Resources Information Center

Sánchez, María Teresa; García, Ofelia; Solorza, Cristian

2018-01-01

This article addresses language allocation policies in what is increasingly called "Dual Language Education" (DLE) in the U.S., offering a challenge to the strict language separation policies in those programs and a proposal for flexibility that transforms them into "Dual Language Bilingual Education" (DLBE). The article offers…

Opening a Window into Reading Development: Eye Movements' Role within a Broader Literacy Research Framework

ERIC Educational Resources Information Center

Miller, Brett; O'Donnell, Carol

2013-01-01

insight into how readers process text. The heart of this work spans roughly 40 years reflecting the maturity of both the topics under study and experimental approaches used to investigate reading. Recent technological advancements offer increased flexibility to the field, providing…