Using machine learning to produce near surface soil moisture estimates from deeper in situ records at U.S. Climate Reference Network (USCRN) locations: Analysis and applications to AMSR-E satellite validation

NASA Astrophysics Data System (ADS)

Coopersmith, Evan J.; Cosh, Michael H.; Bell, Jesse E.; Boyles, Ryan

2016-12-01

Surface soil moisture is a critical parameter for understanding the energy flux at the land atmosphere boundary. Weather modeling, climate prediction, and remote sensing validation are some of the applications for surface soil moisture information. The most common in situ measurement for these purposes are sensors that are installed at depths of approximately 5 cm. There are however, sensor technologies and network designs that do not provide an estimate at this depth. If soil moisture estimates at deeper depths could be extrapolated to the near surface, in situ networks providing estimates at other depths would see their values enhanced. Soil moisture sensors from the U.S. Climate Reference Network (USCRN) were used to generate models of 5 cm soil moisture, with 10 cm soil moisture measurements and antecedent precipitation as inputs, via machine learning techniques. Validation was conducted with the available, in situ, 5 cm resources. It was shown that a 5 cm estimate, which was extrapolated from a 10 cm sensor and antecedent local precipitation, produced a root-mean-squared-error (RMSE) of 0.0215 m3/m3. Next, these machine-learning-generated 5 cm estimates were also compared to AMSR-E estimates at these locations. These results were then compared with the performance of the actual in situ readings against the AMSR-E data. The machine learning estimates at 5 cm produced an RMSE of approximately 0.03 m3/m3 when an optimized gain and offset were applied. This is necessary considering the performance of AMSR-E in locations characterized by high vegetation water contents, which are present across North Carolina. Lastly, the application of this extrapolation technique is applied to the ECONet in North Carolina, which provides a 10 cm depth measurement as its shallowest soil moisture estimate. A raw RMSE of 0.028 m3/m3 was achieved, and with a linear gain and offset applied at each ECONet site, an RMSE of 0.013 m3/m3 was possible.

LiDAR and Field Observations of Earthquake Slip Distribution for the central San Jacinto fault

NASA Astrophysics Data System (ADS)

Salisbury, J. B.; Rockwell, T. K.; Middleton, T.; Hudnut, K. W.

2010-12-01

We mapped the tectonic geomorphology of 80 km of the Clark strand of the San Jacinto fault to determine slip per event for the past several surface ruptures. From the southeastern end of Clark Valley (east of Borrego Springs) northwest to the mouth of Blackburn Canyon (near Hemet), we identify 203 offset geomorphic features from which we make over 560 measurements on channel margins, channel thalwegs, ridge noses, and bar crests using filtered B4 LiDAR imagery, aerial photography, and field observations. Displacement estimates show that the most recent large event (MRE) produced an average of 2.5-2.9 m of right-lateral slip, with maximum slip of 3.5 to 4 m at Anza. Double-event offsets for the same 80 km section average ~5.5 m of right-lateral slip. Maximum values near Anza are estimated to be close to 3 m for the penultimate event, suggesting that the penultimate event was similar in size to the MRE. The third event is also similar in size, with cumulative displacement of 9-10 m through Anza for the past three events. Magnitude estimates for the MRE range from Mw 7.2 to Mw 7.5, depending on how far north the rupture continued. Historically, no earthquakes reported along the Clark fault are large enough to have produced the offset geomorphology we observe. However, recent paleoseismic work at Hog Lake dates the most recent surface rupture event at ca. 1790, potentially placing this event in the historic period. A poorly located, large earthquake occurred on November 22, 1800, and is reported to have caused extensive damage (MMI VII) at the San Diego and San Juan Capistrano missions. We infer slightly lower intensity values for the two missions (MMI VI-VII instead of VII) and relocate this event on the Clark fault based on dating of the MRE at Hog Lake. We also recognize the occurrence of a younger offset along ~15-20 km of the fault in Blackburn Canyon, apparently due to lower slip in that area in the November 22, 1800 event. With average displacement of ~1.25 m, we attribute these offsets to the M6.9 April 21, 1918 event. These data argue that much or all of the Clark fault, and possibly also the Casa Loma fault fail together in large earthquakes, but that shorter sections may also fail in smaller events.

Joint channel/frequency offset estimation and correction for coherent optical FBMC/OQAM system

NASA Astrophysics Data System (ADS)

Wang, Daobin; Yuan, Lihua; Lei, Jingli; wu, Gang; Li, Suoping; Ding, Runqi; Wang, Dongye

2017-12-01

In this paper, we focus on analysis of the preamble-based joint estimation for channel and laser-frequency offset (LFO) in coherent optical filter bank multicarrier systems with offset quadrature amplitude modulation (CO-FBMC/OQAM). In order to reduce the noise impact on the estimation accuracy, we proposed an estimation method based on inter-frame averaging. This method averages the cross-correlation function of real-valued pilots within multiple FBMC frames. The laser-frequency offset is estimated according to the phase of this average. After correcting LFO, the final channel response is also acquired by averaging channel estimation results within multiple frames. The principle of the proposed method is analyzed theoretically, and the preamble structure is thoroughly designed and optimized to suppress the impact of inherent imaginary interference (IMI). The effectiveness of our method is demonstrated numerically using different fiber and LFO values. The obtained results show that the proposed method can improve transmission performance significantly.

Surface rupture of the 2002 Denali fault, Alaska, earthquake and comparison with other strike-slip ruptures

USGS Publications Warehouse

Haeussler, Peter J.; Schwartz, D.P.; Dawson, T.E.; Stenner, Heidi D.; Lienkaemper, J.J.; Cinti, F.; Montone, Paola; Sherrod, B.; Craw, P.

2004-01-01

On 3 November 2002, an M7.9 earthquake produced 340 km of surface rupture on the Denali and two related faults in Alaska. The rupture proceeded from west to east and began with a 40-km-long break on a previously unknown thrust fault. Estimates of surface slip on this thrust are 3-6 m. Next came the principal surface break along ???218 km of the Denali fault. Right-lateral offsets averaged around 5 m and increased eastward to a maximum of nearly 9 m. The fault also ruptured beneath the trans-Alaska oil pipeline, which withstood almost 6 m of lateral offset. Finally, slip turned southeastward onto the Totschunda fault. Right-lateral offsets are up to 3 m, and the surface rupture is about 76 km long. This three-part rupture ranks among the longest strike-slip events of the past two centuries. The earthquake is typical when compared to other large earthquakes on major intracontinental strike-slip faults. ?? 2004, Earthquake Engineering Research Institute.

Improved dichotomous search frequency offset estimator for burst-mode continuous phase modulation

NASA Astrophysics Data System (ADS)

Zhai, Wen-Chao; Li, Zan; Si, Jiang-Bo; Bai, Jun

2015-11-01

A data-aided technique for carrier frequency offset estimation with continuous phase modulation (CPM) in burst-mode transmission is presented. The proposed technique first exploits a special pilot sequence, or training sequence, to form a sinusoidal waveform. Then, an improved dichotomous search frequency offset estimator is introduced to determine the frequency offset using the sinusoid. Theoretical analysis and simulation results indicate that our estimator is noteworthy in the following aspects. First, the estimator can operate independently of timing recovery. Second, it has relatively low outlier, i.e., the minimum signal-to-noise ratio (SNR) required to guarantee estimation accuracy. Finally, the most important property is that our estimator is complexity-reduced compared to the existing dichotomous search methods: it eliminates the need for fast Fourier transform (FFT) and modulation removal, and exhibits faster convergence rate without accuracy degradation. Project supported by the National Natural Science Foundation of China (Grant No. 61301179), the Doctorial Programs Foundation of the Ministry of Education, China (Grant No. 20110203110011), and the Programme of Introducing Talents of Discipline to Universities, China (Grant No. B08038).

Accounting for Uncertainty and Time Lags in Equivalency Calculations for Offsetting in Aquatic Resources Management Programs

NASA Astrophysics Data System (ADS)

Bradford, Michael J.

2017-10-01

Biodiversity offset programs attempt to minimize unavoidable environmental impacts of anthropogenic activities by requiring offsetting measures in sufficient quantity to counterbalance losses due to the activity. Multipliers, or offsetting ratios, have been used to increase the amount of offsets to account for uncertainty but those ratios have generally been derived from theoretical or ad-hoc considerations. I analyzed uncertainty in the offsetting process in the context of offsetting for impacts to freshwater fisheries productivity. For aquatic habitats I demonstrate that an empirical risk-based approach for evaluating prediction uncertainty is feasible, and if data are available appropriate adjustments to offset requirements can be estimated. For two data-rich examples I estimate multipliers in the range of 1.5:1 - 2.5:1 are sufficient to account for the uncertainty in the prediction of gains and losses. For aquatic habitats adjustments for time delays in the delivery of offset benefits can also be calculated and are likely smaller than those for prediction uncertainty. However, the success of a biodiversity offsetting program will also depend on the management of the other components of risk not addressed by these adjustments.

Accounting for Uncertainty and Time Lags in Equivalency Calculations for Offsetting in Aquatic Resources Management Programs.

PubMed

Bradford, Michael J

2017-10-01

Biodiversity offset programs attempt to minimize unavoidable environmental impacts of anthropogenic activities by requiring offsetting measures in sufficient quantity to counterbalance losses due to the activity. Multipliers, or offsetting ratios, have been used to increase the amount of offsets to account for uncertainty but those ratios have generally been derived from theoretical or ad-hoc considerations. I analyzed uncertainty in the offsetting process in the context of offsetting for impacts to freshwater fisheries productivity. For aquatic habitats I demonstrate that an empirical risk-based approach for evaluating prediction uncertainty is feasible, and if data are available appropriate adjustments to offset requirements can be estimated. For two data-rich examples I estimate multipliers in the range of 1.5:1 - 2.5:1 are sufficient to account for the uncertainty in the prediction of gains and losses. For aquatic habitats adjustments for time delays in the delivery of offset benefits can also be calculated and are likely smaller than those for prediction uncertainty. However, the success of a biodiversity offsetting program will also depend on the management of the other components of risk not addressed by these adjustments.

Pulsar Pair Cascades in Magnetic Fields with Offset Polar Caps

NASA Technical Reports Server (NTRS)

Harding, Alice K.; Muslimov, Alex G.

2012-01-01

Neutron star magnetic fields may have polar caps (PC) that are offset from the dipole axis, through field-line sweepback near the light cylinder or non-symmetric currents within the star. The effects of such offsets on electron-positron pair cascades are investigated, using simple models of dipole magnetic fields with small distortions that shift the PCs by different amounts or directions. Using a Monte Carlo pair cascade simulation, we explore the changes in the pair spectrum, multiplicity and energy flux across the PC, as well as the trends in pair flux and pair energy flux with spin-down luminosity, L(sub sd). We also give an estimate of the distribution of heating flux from returning positrons on the PC for different offsets. We find that even modest offsets can produce significant increases in pair multiplicity, especially for pulsars that are near or beyond the pair death lines for centered PCs, primarily because of higher accelerating fields. Pair spectra cover several decades in energy, with the spectral range of millisecond pulsars (MSPs) two orders of magnitude higher than for normal pulsars, and PC offsets allow significant extension of all spectra to lower pair energies. We find that the total PC pair luminosity L(sub pair) is proportional to L(sub sd), with L(sub pair) approximates 10(exp -3) L(sub sd) for normal pulsars and L(sub pair) approximates 10(exp -2) L(sub sd) for MSPs. Remarkably, the total PC heating luminosity for even large offsets increases by less than a factor of two, even though the PC area increases by much larger factors, because most of the heating occurs near the magnetic axis.

Autoregressive Processes in Homogenization of GNSS Tropospheric Data

NASA Astrophysics Data System (ADS)

Klos, A.; Bogusz, J.; Teferle, F. N.; Bock, O.; Pottiaux, E.; Van Malderen, R.

2016-12-01

Offsets due to changes in hardware equipment or any other artificial event are all a subject of a task of homogenization of tropospheric data estimated within a processing of Global Navigation Satellite System (GNSS) observables. This task is aimed at identifying exact epochs of offsets and estimate their magnitudes since they may artificially under- or over-estimate trend and its uncertainty delivered from tropospheric data and used in climate studies. In this research, we analysed a common data set of differences of Integrated Water Vapour (IWV) from GPS and ERA-Interim (1995-2010) provided for a homogenization group working within ES1206 COST Action GNSS4SWEC. We analysed daily IWV records of GPS and ERA-Interim in terms of trend, seasonal terms and noise model with Maximum Likelihood Estimation in Hector software. We found that this data has a character of autoregressive process (AR). Basing on this analysis, we performed Monte Carlo simulations of 25 years long data with two different noise types: white as well as combination of white and autoregressive and also added few strictly defined offsets. This synthetic data set of exactly the same character as IWV from GPS and ERA-Interim was then subjected to a task of manual and automatic/statistical homogenization. We made blind tests and detected possible epochs of offsets manually. We found that simulated offsets were easily detected in series with white noise, no influence of seasonal signal was noticed. The autoregressive series were much more problematic when offsets had to be determined. We found few epochs, for which no offset was simulated. This was mainly due to strong autocorrelation of data, which brings an artificial trend within. Due to regime-like behaviour of AR it is difficult for statistical methods to properly detect epochs of offsets, which was previously reported by climatologists.

Offset-Free Model Predictive Control of Open Water Channel Based on Moving Horizon Estimation

NASA Astrophysics Data System (ADS)

Ekin Aydin, Boran; Rutten, Martine

2016-04-01

Model predictive control (MPC) is a powerful control option which is increasingly used by operational water managers for managing water systems. The explicit consideration of constraints and multi-objective management are important features of MPC. However, due to the water loss in open water systems by seepage, leakage and evaporation a mismatch between the model and the real system will be created. These mismatch affects the performance of MPC and creates an offset from the reference set point of the water level. We present model predictive control based on moving horizon estimation (MHE-MPC) to achieve offset free control of water level for open water canals. MHE-MPC uses the past predictions of the model and the past measurements of the system to estimate unknown disturbances and the offset in the controlled water level is systematically removed. We numerically tested MHE-MPC on an accurate hydro-dynamic model of the laboratory canal UPC-PAC located in Barcelona. In addition, we also used well known disturbance modeling offset free control scheme for the same test case. Simulation experiments on a single canal reach show that MHE-MPC outperforms disturbance modeling offset free control scheme.

Differential comparator cirucit

DOEpatents

Hickling, Ronald M.

1996-01-01

A differential comparator circuit for an Analog-to-Digital Converter (ADC) or other application includes a plurality of differential comparators and a plurality of offset voltage generators. Each comparator includes first and second differentially connected transistor pairs having equal and opposite voltage offsets. First and second offset control transistors are connected in series with the transistor pairs respectively. The offset voltage generators generate offset voltages corresponding to reference voltages which are compared with a differential input voltage by the comparators. Each offset voltage is applied to the offset control transistors of at least one comparator to set the overall voltage offset of the comparator to a value corresponding to the respective reference voltage. The number of offset voltage generators required in an ADC application can be reduced by a factor of approximately two by applying the offset voltage from each offset voltage generator to two comparators with opposite logical sense such that positive and negative offset voltages are produced by each offset voltage generator.

Energy Balance Bowen Ratio (EBBR) Handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, D. R.

2016-01-01

The Energy Balance Bowen Ratio (EBBR) system produces 30-minute estimates of the vertical fluxes of sensible and latent heat at the local surface. Flux estimates are calculated from observations of net radiation, soil surface heat flux, and the vertical gradients of temperature and relative humidity (RH). Meteorological data collected by the EBBR are used to calculate bulk aerodynamic fluxes, which are used in the Bulk Aerodynamic Technique (BA) EBBR value-added product (VAP) to replace sunrise and sunset spikes in the flux data. A unique aspect of the system is the automatic exchange mechanism (AEM), which helps to reduce errors frommore » instrument offset drift.« less

Energy Balance Bowen Ratio Station (EBBR) Handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, DR

2011-02-23

The energy balance Bowen ratio (EBBR) system produces 30-minute estimates of the vertical fluxes of sensible and latent heat at the local surface. Flux estimates are calculated from observations of net radiation, soil surface heat flux, and the vertical gradients of temperature and relative humidity (RH). Meteorological data collected by the EBBR are used to calculate bulk aerodynamic fluxes, which are used in the Bulk Aerodynamic Technique (BA) EBBR value-added product (VAP) to replace sunrise and sunset spikes in the flux data. A unique aspect of the system is the automatic exchange mechanism (AEM), which helps to reduce errors frommore » instrument offset drift.« less

Experimental demonstration of a 16.9 Gb/s link for coherent OFDM PON robust to frequency offset and timing error

NASA Astrophysics Data System (ADS)

Ma, Qian; Liu, Yu; Xiang, Yuanjiang

2018-07-01

Due to its merits of flexible bandwidth allocation and robustness towards fiber transmission impairments, coherent optical orthogonal frequency division multiplexing (CO-OFDM) technology draws a lot of attention for passive optical networks (PON). However, a CO-OFDM system is vulnerable to frequency offsets between modulated optical signals and optical local oscillators (OLO). This is particularly serious for low cost PONs where low cost lasers are used. Thus, it is of great interest to develop efficient algorithms for frequency synchronization in CO-OFDM systems. Usually frequency synchronization proposed in CO-OFDM systems are done by detecting the phase shift in time domain. In such a way, there is a trade-off between estimation accuracy and range. Considering that the integer frequency offset (IFO) contributes to the major frequency offset, a more efficient method to estimate IFO is of demand. By detecting IFO induced circular channel rotation (CCR), the frequency offset can be directly estimated after fast Fourier transforming (FFT). In this paper, circular acquisition offset frequency and timing synchronization (CAO-FTS) scheme is proposed. A specially-designed frequency domain pseudo noise (PN) sequence is used for CCR detection and timing synchronization. Full-range frequency offset compensation and non-plateau timing synchronization are experimentally demonstrated in presence of fiber dispersion. Based on CAO-FTS, 16.9 Gb/s CO-OFDM signal is successfully delivered over a span of 80-km single mode fiber.

Current Trend Towards Using Soft Computing Approaches to Phase Synchronization in Communication Systems

NASA Technical Reports Server (NTRS)

Drake, Jeffrey T.; Prasad, Nadipuram R.

1999-01-01

This paper surveys recent advances in communications that utilize soft computing approaches to phase synchronization. Soft computing, as opposed to hard computing, is a collection of complementary methodologies that act in producing the most desirable control, decision, or estimation strategies. Recently, the communications area has explored the use of the principal constituents of soft computing, namely, fuzzy logic, neural networks, and genetic algorithms, for modeling, control, and most recently for the estimation of phase in phase-coherent communications. If the receiver in a digital communications system is phase-coherent, as is often the case, phase synchronization is required. Synchronization thus requires estimation and/or control at the receiver of an unknown or random phase offset.

Discrimination of winter wheat on irrigated land in southern Finney County, Kansas

NASA Technical Reports Server (NTRS)

Morain, S. A. (Principal Investigator); Williams, D. L.; Barker, B.; Coiner, J. C.

1973-01-01

The author has identified the following significant results. Winter wheat in the large field irrigated landscape of southern Finney County, Kansas was successfully discriminated by use of 4 ERTS-1 images. These images were acquired 16 August 1972, 21 September 1972, and 2 December 1972. MSS-5 images from each date and the MSS-7 image from 2 December 1972 were used. Human interpretation of the four images resulted in a classification scheme which produced 98% correct estimation of the number of wheat fields in the training sample and 100% correct estimation in the test sample. Overall correct separation of wheat from non-wheat fields was 93% and 86%, respectively. Offsetting errors resulted in the estimation accuracy for wheat.

Fast Kalman Filtering for Relative Spacecraft Position and Attitude Estimation for the Raven ISS Hosted Payload

NASA Technical Reports Server (NTRS)

Galante, Joseph M.; Van Eepoel, John; D'Souza, Chris; Patrick, Bryan

2016-01-01

The Raven ISS Hosted Payload will feature several pose measurement sensors on a pan/tilt gimbal which will be used to autonomously track resupply vehicles as they approach and depart the International Space Station. This paper discusses the derivation of a Relative Navigation Filter (RNF) to fuse measurements from the different pose measurement sensors to produce relative position and attitude estimates. The RNF relies on relative translation and orientation kinematics and careful pose sensor modeling to eliminate dependence on orbital position information and associated orbital dynamics models. The filter state is augmented with sensor biases to provide a mechanism for the filter to estimate and mitigate the offset between the measurements from different pose sensors

Fast Kalman Filtering for Relative Spacecraft Position and Attitude Estimation for the Raven ISS Hosted Payload

NASA Technical Reports Server (NTRS)

Galante, Joseph M.; Van Eepoel, John; D' Souza, Chris; Patrick, Bryan

2016-01-01

The Raven ISS Hosted Payload will feature several pose measurement sensors on a pan/tilt gimbal which will be used to autonomously track resupply vehicles as they approach and depart the International Space Station. This paper discusses the derivation of a Relative Navigation Filter (RNF) to fuse measurements from the different pose measurement sensors to produce relative position and attitude estimates. The RNF relies on relative translation and orientation kinematics and careful pose sensor modeling to eliminate dependence on orbital position information and associated orbital dynamics models. The filter state is augmented with sensor biases to provide a mechanism for the filter to estimate and mitigate the offset between the measurements from different pose sensors.

Correlation between centre offsets and gas velocity dispersion of galaxy clusters in cosmological simulations

NASA Astrophysics Data System (ADS)

Li, Ming-Hua; Zhu, Weishan; Zhao, Dong

2018-05-01

The gas is the dominant component of baryonic matter in most galaxy groups and clusters. The spatial offsets of gas centre from the halo centre could be an indicator of the dynamical state of cluster. Knowledge of such offsets is important for estimate the uncertainties when using clusters as cosmological probes. In this paper, we study the centre offsets roff between the gas and that of all the matter within halo systems in ΛCDM cosmological hydrodynamic simulations. We focus on two kinds of centre offsets: one is the three-dimensional PB offsets between the gravitational potential minimum of the entire halo and the barycentre of the ICM, and the other is the two-dimensional PX offsets between the potential minimum of the halo and the iterative centroid of the projected synthetic X-ray emission of the halo. Haloes at higher redshifts tend to have larger values of rescaled offsets roff/r200 and larger gas velocity dispersion σ v^gas/σ _{200}. For both types of offsets, we find that the correlation between the rescaled centre offsets roff/r200 and the rescaled 3D gas velocity dispersion, σ _v^gas/σ _{200} can be approximately described by a quadratic function as r_{off}/r_{200} ∝ (σ v^gas/σ _{200} - k_2)2. A Bayesian analysis with MCMC method is employed to estimate the model parameters. Dependence of the correlation relation on redshifts and the gas mass fraction are also investigated.

Redox artifacts in electrophysiological recordings

PubMed Central

Berman, Jonathan M.

2013-01-01

Electrophysiological techniques make use of Ag/AgCl electrodes that are in direct contact with cells or bath. In the bath, electrodes are exposed to numerous experimental conditions and chemical reagents that can modify electrode voltage. We examined voltage offsets created in Ag/AgCl electrodes by exposure to redox reagents used in electrophysiological studies. Voltage offsets were measured in reference to an electrode separated from the solution by an agar bridge. The reducing reagents Tris-2-carboxyethly-phosphine, dithiothreitol (DTT), and glutathione, as well as the oxidizing agent H2O2 used at experimentally relevant concentrations reacted with Ag in the electrodes to produce voltage offsets. Chloride ions and strong acids and bases produced offsets at millimolar concentrations. Electrolytic depletion of the AgCl layer, to replicate voltage clamp and sustained use, resulted in increased sensitivity to flow and DTT. Offsets were sensitive to electrode silver purity and to the amount and method of chloride deposition. For example, exposure to 10 μM DTT produced a voltage offset between 10 and 284 mV depending on the chloride deposition method. Currents generated by these offsets are significant and dependent on membrane conductance and by extension the expression of ion channels and may therefore appear to be biological in origin. These data demonstrate a new source of artifacts in electrophysiological recordings that can affect measurements obtained from a variety of experimental techniques from patch clamp to two-electrode voltage clamp. PMID:23344161

Economic and ecological outcomes of flexible biodiversity offset systems.

PubMed

Habib, Thomas J; Farr, Daniel R; Schneider, Richard R; Boutin, Stan

2013-12-01

The commonly expressed goal of biodiversity offsets is to achieve no net loss of specific biological features affected by development. However, strict equivalency requirements may complicate trading of offset credits, increase costs due to restricted offset placement options, and force offset activities to focus on features that may not represent regional conservation priorities. Using the oil sands industry of Alberta, Canada, as a case study, we evaluated the economic and ecological performance of alternative offset systems targeting either ecologically equivalent areas (vegetation types) or regional conservation priorities (caribou and the Dry Mixedwood natural subregion). Exchanging dissimilar biodiversity elements requires assessment via a generalized metric; we used an empirically derived index of biodiversity intactness to link offsets with losses incurred by development. We considered 2 offset activities: land protection, with costs estimated as the net present value of profits of petroleum and timber resources to be paid as compensation to resource tenure holders, and restoration of anthropogenic footprint, with costs estimated from existing restoration projects. We used the spatial optimization tool MARXAN to develop hypothetical offset networks that met either the equivalent-vegetation or conservation-priority targets. Networks that required offsetting equivalent vegetation cost 2-17 times more than priority-focused networks. This finding calls into question the prudence of equivalency-based systems, particularly in relatively undeveloped jurisdictions, where conservation focuses on limiting and directing future losses. Priority-focused offsets may offer benefits to industry and environmental stakeholders by allowing for lower-cost conservation of valued ecological features and may invite discussion on what land-use trade-offs are acceptable when trading biodiversity via offsets. Resultados Económicos y Ecológicos de Sistemas de Compensación de Biodiversidad Flexible Habib et al. © 2013 Society for Conservation Biology.

Multi-offset GPR methods for hyporheic zone investigations

USGS Publications Warehouse

Brosten, T.R.; Bradford, J.H.; McNamara, J.P.; Gooseff, M.N.; Zarnetske, J.P.; Bowden, W.B.; Johnston, M.E.

2009-01-01

Porosity of stream sediments has a direct effect on hyporheic exchange patterns and rates. Improved estimates of porosity heterogeneity will yield enhanced simulation of hyporheic exchange processes. Ground-penetrating radar (GPR) velocity measurements are strongly controlled by water content thus accurate measures of GPR velocity in saturated sediments provides estimates of porosity beneath stream channels using petrophysical relationships. Imaging the substream system using surface based reflection measurements is particularly challenging due to large velocity gradients that occur at the transition from open water to saturated sediments. The continuous multi-offset method improves the quality of subsurface images through stacking and provides measurements of vertical and lateral velocity distributions. We applied the continuous multi-offset method to stream sites on the North Slope, Alaska and the Sawtooth Mountains near Boise, Idaho, USA. From the continuous multi-offset data, we measure velocity using reflection tomography then estimate water content and porosity using the Topp equation. These values provide detailed measurements for improved stream channel hydraulic and thermal modelling. ?? 2009 European Association of Geoscientists & Engineers.

New insight into the 1556 M8 Huaxian earthquake in China

NASA Astrophysics Data System (ADS)

Ma, J.

2017-12-01

The disastrous 1556 M8 Huaxian earthquake in China took away 0.8Ma lives then as well as attracted scientists' attention. Although the Huashan front fault and Weinan plateform-front fault at the south margin of Weihe basin was responsible for this earthquake, we know less about the fault behaviors. There's evidence that the modern riverbank offset and older geomorphic scarps in Chishui river site on Weinan plateau-front fault from the Pleiades DEM. Here, we did a 3D trench excavation model using SfM work, drilling profiles and geomorphological measurement there to revive the site for multiearthquakes. It turns out two events occurred on the normal fault with pretty high offsets 9.4m and 7.8-8.0m respectively, the later one resulted from Huaxian earthquake. And we estimate that the fault slip rate approximately 1.48-1.75 mm/a. Thus, we find that the older earthquake also produced a similar fault offsets to the 1556 earthquake showing as characteristics earthquake. The paleoseismic study demonstrates that the Weinan pateform-front fault plays a role in boundary faults of Weihe basin, which can contribute to the basin evolution of regions of active faulting.

LCDs are better: psychophysical and photometric estimates of the temporal characteristics of CRT and LCD monitors.

PubMed

Lagroix, Hayley E P; Yanko, Matthew R; Spalek, Thomas M

2012-07-01

Many cognitive and perceptual phenomena, such as iconic memory and temporal integration, require brief displays. A critical requirement is that the image not remain visible after its offset. It is commonly believed that liquid crystal displays (LCD) are unsuitable because of their poor temporal response characteristics relative to cathode-ray-tube (CRT) screens. Remarkably, no psychophysical estimates of visible persistence are available to verify this belief. A series of experiments in which white stimuli on a black background produced discernible persistence on CRT but not on LCD screens, during both dark- and light-adapted viewing, falsified this belief. Similar estimates using black stimuli on a white background produced no visible persistence on either screen. That said, photometric measurements are available that seem to confirm the poor temporal characteristics of LCD screens, but they were obtained before recent advances in LCD technology. Using current LCD screens, we obtained photometric estimates of rise time far shorter (1-6 ms) than earlier estimates (20-150 ms), and approaching those of CRTs (<1 ms). We conclude that LCDs are preferable to CRTs when visible persistence is a concern, except when black-on-white displays are used.

Estimation of scattering object characteristics for image reconstruction using a nonzero background.

PubMed

Jin, Jing; Astheimer, Jeffrey; Waag, Robert

2010-06-01

Two methods are described to estimate the boundary of a 2-D penetrable object and the average sound speed in the object. One method is for circular objects centered in the coordinate system of the scattering observation. This method uses an orthogonal function expansion for the scattering. The other method is for noncircular, essentially convex objects. This method uses cross correlation to obtain time differences that determine a family of parabolas whose envelope is the boundary of the object. A curve-fitting method and a phase-based method are described to estimate and correct the offset of an uncentered radial or elliptical object. A method based on the extinction theorem is described to estimate absorption in the object. The methods are applied to calculated scattering from a circular object with an offset and to measured scattering from an offset noncircular object. The results show that the estimated boundaries, sound speeds, and absorption slopes agree very well with independently measured or true values when the assumptions of the methods are reasonably satisfied.

Modeling the refraction of microbaroms by the winds of a large maritime storm.

PubMed

Blom, Philip; Waxler, Roger

2017-12-01

Continuous infrasonic signals produced by the ocean surface interacting with the atmosphere, termed microbaroms, are known to be generated by a number of phenomena including large maritime storms. Storm generated microbaroms exhibit axial asymmetry when observed at locations far from the storm due to the source location being offset from the storm center. Because of this offset, a portion of the microbarom energy will radiate towards the storm center and interact with the winds in the region. Detailed here are predictions for the propagation of microbaroms through an axisymmetric, three-dimensional model storm. Geometric propagation methods have been utilized and the predicted horizontal refraction is found to produce signals that appear to emanate from a virtual source near the storm center when observed far from the storm. This virtual source near the storm center is expected to be observed only from a limited arc around the storm system with increased extent associated with more intense wind fields. This result implies that identifying the extent of the arc observing signal from the virtual source could provide a means to estimate the wind structure using infrasonic observations far from the storm system.

On Frequency Offset Estimation Using the iNET Preamble in Frequency Selective Fading Channels

DTIC Science & Technology

2014-03-01

ASM fields; (bottom) the relationship between the indexes of the received samples r(n), the signal samples s(n), the preamble samples p (n) and the short...frequency offset estimators for SOQPSK-TG equipped with the iNET preamble and operating in ISI channels. Four of the five estimators exam - ined here are...sync marker ( ASM ), and data bits (an LDPC codeword). The availability of a preamble introduces the possibility of data-aided synchro- nization in

Time maintenance system for the BMDO MSX spacecraft

NASA Technical Reports Server (NTRS)

Hermes, Martin J.

1994-01-01

The Johns Hopkins University Applied Physics Laboratory (APL) is responsible for designing and implementing a clock maintenance system for the Ballistic Missile Defense Organizations (BMDO) Midcourse Space Experiment (MSX) spacecraft. The MSX spacecraft has an on-board clock that will be used to control execution of time-dependent commands and to time tag all science and housekeeping data received from the spacecraft. MSX mission objectives have dictated that this spacecraft time, UTC(MSX), maintain a required accuracy with respect to UTC(USNO) of +/- 10 ms with a +/- 1 ms desired accuracy. APL's atomic time standards and the downlinked spacecraft time were used to develop a time maintenance system that will estimate the current MSX clock time offset during an APL pass and make estimates of the clock's drift and aging using the offset estimates from many passes. Using this information, the clock's accuracy will be maintained by uplinking periodic clock correction commands. The resulting time maintenance system is a combination of offset measurement, command/telemetry, and mission planning hardware and computing assets. All assets provide necessary inputs for deciding when corrections to the MSX spacecraft clock must be made to maintain its required accuracy without inhibiting other mission objectives. The MSX time maintenance system is described as a whole and the clock offset measurement subsystem, a unique combination of precision time maintenance and measurement hardware controlled by a Macintosh computer, is detailed. Simulations show that the system estimates the MSX clock offset to less than+/- 33 microseconds.

Attenuation of multiples in image space

NASA Astrophysics Data System (ADS)

Alvarez, Gabriel F.

In complex subsurface areas, attenuation of 3D specular and diffracted multiples in data space is difficult and inaccurate. In those areas, image space is an attractive alternative. There are several reasons: (1) migration increases the signal-to-noise ratio of the data; (2) primaries are mapped to coherent events in Subsurface Offset Domain Common Image Gathers (SODCIGs) or Angle Domain Common Image Gathers (ADCIGs); (3) image space is regular and smaller; (4) attenuating the multiples in data space leaves holes in the frequency-Wavenumber space that generate artifacts after migration. I develop a new equation for the residual moveout of specular multiples in ADCIGs and use it for the kernel of an apex-shifted Radon transform to focus and separate the primaries from specular and diffracted multiples. Because of small amplitude, phase and kinematic errors in the multiple estimate, we need adaptive matching and subtraction to estimate the primaries. I pose this problem as an iterative least-squares inversion that simultaneously matches the estimates of primaries and multiples to the data. Standard methods match only the estimate of the multiples. I demonstrate with real and synthetic data that the method produces primaries and multiples with little cross-talk. In 3D, the multiples exhibit residual moveout in SODCIGs in in-line and cross-line offsets. They map away from zero subsurface offsets when migrated with the faster velocity of the primaries. In ADCIGs the residual moveout of the primaries as a function of the aperture angle, for a given azimuth, is flat for those angles that illuminate the reflector. The multiples have residual moveout towards increasing depth for increasing aperture angles at all azimuths. As a function of azimuth, the primaries have better azimuth resolution than the multiples at larger aperture angles. I show, with a real 3D dataset, that even below salt, where illumination is poor, the multiples are well attenuated in ADCIGs with the new Radon transform in planes of azimuth-stacked ADCIGs. The angle stacks of the estimated primaries show little residual multiple energy.

Characterization for capillary barriers effects in a sand box test using time-lapsed GPR measurements

NASA Astrophysics Data System (ADS)

Kuroda, S.; Ishii, N.; Morii, T.

2017-12-01

Capillary barriers have been known as the method to protect subsurface regions against infiltration from soil surface. It is caused by essentially heterogeneous structure in permeability or soil physical property and produce non-uniform infiltration process then, in order to estimate the actual situation of the capillary barrier effect, the site-characterization with imaging technique like geophysical prospecting is effective. In this study, we examine the applicability of GPR to characterization for capillary barriers. We built a sand box with 90x340x90cm in which a thin high-permeable gravel layer was embedded as a capillary barrier. We conducted an infiltration test in the sand box using porous tube array for irrigation. It is expected to lead to non-uniform flow of soil water induced by capillary barrier effects. We monitored this process by various types of GPR measurements, including time-lapsed common offset profiling (COP) with multi- frequency antenna and transmission measurements like cross-borehole radar. At first, we conducted GPR common-offset survey. It could show the depth of capillary barrier in sand box. After that we conducted the infiltration test and GPR monitoring for infiltration process. GPR profiles can detect the wetting front and estimate water content change in the soil layer above the capillary barrier. From spatial change in these results we can estimate the effect of capillary barrier and the zone where the break through occur or not. Based on these results, we will discuss the applicability of GPR for monitoring the phenomena around the capillary barrier of soil. At first, we conducted GPR common-offset survey. It could show the depth of capillary barrier in sand box. After that we conducted the infiltration test and GPR monitoring for infiltration process. GPR profiles can detect the wetting front and estimate water content change in the soil layer above the capillary barrier. From spatial change in these results we can estimate the effect of capillary barrier and the zone where the break through occur. Based on these results, we will discuss the applicability of GPR for monitoring the phenomena around the capillary barrier of soil.

LiDAR and field observations of slip distribution for the most recent surface ruptures along the central San Jacinto fault

USGS Publications Warehouse

J.B. Salisbury,; T.K. Rockwell,; T.J. Middleton,; Hudnut, Kenneth W.

2012-01-01

We measured offsets on tectonically displaced geomorphic features along 80 km of the Clark strand of the San Jacinto fault (SJF) to estimate slip‐per‐event for the past several surface ruptures. We identify 168 offset features from which we make over 490 measurements using B4 light detection and ranging (LiDAR) imagery and field observations. Our results suggest that LiDAR technology is an exemplary supplement to traditional field methods in slip‐per‐event studies. Displacement estimates indicate that the most recent surface‐rupturing event (MRE) produced an average of 2.5–2.9 m of right‐lateral slip with maximum slip of nearly 4 m at Anza, a Mw 7.2–7.5 earthquake. Average multiple‐event offsets for the same 80 kms are ∼5.5  m, with maximum values of 3 m at Anza for the penultimate event. Cumulative displacements of 9–10 m through Anza suggest the third event was also similar in size. Paleoseismic work at Hog Lake dates the most recent surface rupture event at ca. 1790. A poorly located, large earthquake occurred in southern California on 22 November 1800; we relocate this event to the Clark fault based on the MRE at Hog Lake. We also recognize the occurrence of a younger rupture along ∼15–20  km of the fault in Blackburn Canyon with ∼1.25  m of average displacement. We attribute these offsets to the 21 April 1918 Mw 6.9 event. These data argue that much or all of the Clark fault, and possibly also the Casa Loma fault, fail together in large earthquakes, but that shorter sections may fail in smaller events.

Preparation-induced errors in EPR dosimetry of enamel: pre- and post-crushing sensitivity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haskell, E.H.; Hayes, R.B.; Kenner, G.H.

1996-01-01

Errors in dose estimation as a function of grain size for tooth enamel has been previously shown for beta irradiation after crushing. We tested the effect of gamma radiation applied to specimens before and after crushing. We extend the previous work in that we found that post-crushing irradiation altered the slope of the dose-response curve of the hydroxyapatite signal and produced a grain-size dependent offset. No changes in the slope of the dose-response curve were seen in enamel caps irradiated before crushing.

Applied automatic offset detection using HECTOR within EPOS-IP

NASA Astrophysics Data System (ADS)

Fernandes, R. M. S.; Bos, M. S.

2016-12-01

It is well known that offsets are present in most GNSS coordinate time series. These offsets need to be taken into account in the analysis to avoid incorrect estimation of the tectonic motions. The time of the offsets are normally determined by visual inspection of the time series but with the ever increasing amount of GNSS stations, this is becoming too time consuming and automatic offset detection algorithms are required. This is particularly true in projects like EPOS (European Plate Observing System), where the routinely analysis of thousands of daily time-series will be required. It is also planned to include stations installed for technical applications which metadata is also not always properly maintained. In this research we present an offset detection scheme that uses the Bayesian Information Criterion (BIC) to determine the most likely time of an offset. The novelty of this scheme is that it takes the temporal correlation of the noise into account. This aspect is normally ignored due to the fact that it significantly increases the computation time. However, it needs to be taken into account to ensure that the estimated BIC value is correct. We were able to create a fast algorithm by adopting the methodology implemented in HECTOR (Bos et al., 2013). We evaluate the feasibility of the approach using the core IGS network, where most of the offsets have been accurately determined, which permit to have an external evaluation of this new outlier detection approach to be included in HECTOR. We also apply the scheme to regional networks in Iberia where such offsets are often not documented properly in order to compare the normal manual approach with the new automatic approach. Finally, we also compare the optimal approach used by HECTOR with other algorithms such as MIDAS and STARS.

Consistency between satellite-derived and modeled estimates of the direct aerosol effect.

PubMed

Myhre, Gunnar

2009-07-10

In the Intergovernmental Panel on Climate Change Fourth Assessment Report, the direct aerosol effect is reported to have a radiative forcing estimate of -0.5 Watt per square meter (W m(-2)), offsetting the warming from CO2 by almost one-third. The uncertainty, however, ranges from -0.9 to -0.1 W m(-2), which is largely due to differences between estimates from global aerosol models and observation-based estimates, with the latter tending to have stronger (more negative) radiative forcing. This study demonstrates consistency between a global aerosol model and adjustment to an observation-based method, producing a global and annual mean radiative forcing that is weaker than -0.5 W m(-2), with a best estimate of -0.3 W m(-2). The physical explanation for the earlier discrepancy is that the relative increase in anthropogenic black carbon (absorbing aerosols) is much larger than the overall increase in the anthropogenic abundance of aerosols.

Real-time and rapid GNSS solutions from the M8.2 September 2017 Tehuantepec Earthquake and implications for Earthquake and Tsunami Early Warning Systems

NASA Astrophysics Data System (ADS)

Mencin, D.; Hodgkinson, K. M.; Mattioli, G. S.

2017-12-01

In support of hazard research and Earthquake Early Warning (EEW) Systems UNAVCO operates approximately 800 RT-GNSS stations throughout western North America and Alaska (EarthScope Plate Boundary Observatory), Mexico (TLALOCNet), and the pan-Caribbean region (COCONet). Our system produces and distributes raw data (BINEX and RTCM3) and real-time Precise Point Positions via the Trimble PIVOT Platform (RTX). The 2017-09-08 earthquake M8.2 located 98 km SSW of Tres Picos, Mexico is the first great earthquake to occur within the UNAVCO RT-GNSS footprint, which allows for a rigorous analysis of our dynamic and static processing methods. The need for rapid geodetic solutions ranges from seconds (EEW systems) to several minutes (Tsunami Warning and NEIC moment tensor and finite fault models). Here, we compare and quantify the relative processing strategies for producing static offsets, moment tensors and geodetically determined finite fault models using data recorded during this event. We also compare the geodetic solutions with the USGS NEIC seismically derived moment tensors and finite fault models, including displacement waveforms generated from these models. We define kinematic post-processed solutions from GIPSY-OASISII (v6.4) with final orbits and clocks as a "best" case reference to evaluate the performance of our different processing strategies. We find that static displacements of a few centimeters or less are difficult to resolve in the real-time GNSS position estimates. The standard daily 24-hour solutions provide the highest-quality data-set to determine coseismic offsets, but these solutions are delayed by at least 48 hours after the event. Dynamic displacements, estimated in real-time, however, show reasonable agreement with final, post-processed position estimates, and while individual position estimates have large errors, the real-time solutions offer an excellent operational option for EEW systems, including the use of estimated peak-ground displacements or directly inverting for finite-fault solutions. In the near-field, we find that the geodetically-derived moment tensors and finite fault models differ significantly with seismically-derived models, highlighting the utility of using geodetic data in hazard applications.

76 FR 31019 - Distribution of Continued Dumping and Subsidy Offset to Affected Domestic Producers

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-27

...Pursuant to the Continued Dumping and Subsidy Offset Act of 2000, this document is U.S. Customs and Border Protection's notice of intent to distribute assessed antidumping or countervailing duties (known as the continued dumping and subsidy offset) for Fiscal Year 2011 in connection with countervailing duty orders, antidumping duty orders, or findings under the Antidumping Act of 1921. This document sets forth the case name and number of each order or finding for which funds may become available for distribution, together with the list of affected domestic producers, based on the list supplied by the United States International Trade Commission (USITC) associated with each order or finding, who are potentially eligible to receive a distribution. This document also provides the instructions for affected domestic producers (and anyone alleging eligibility to receive a distribution) to file certifications to claim a distribution in relation to the listed orders or findings.

75 FR 30529 - Distribution of Continued Dumping and Subsidy Offset to Affected Domestic Producers

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-01

...Pursuant to the Continued Dumping and Subsidy Offset Act of 2000, this document is U.S. Customs and Border Protection's notice of intent to distribute assessed antidumping or countervailing duties (known as the continued dumping and subsidy offset) for Fiscal Year 2010 in connection with countervailing duty orders, antidumping duty orders, or findings under the Antidumping Act of 1921. This document sets forth the case name and number of each order or finding for which funds may become available for distribution, together with the list of affected domestic producers, based on the list supplied by the United States International Trade Commission (USITC) associated with each order or finding, who are potentially eligible to receive a distribution. This document also provides the instructions for affected domestic producers (and anyone alleging eligibility to receive a distribution) to file certifications to claim a distribution in relation to the listed orders or findings.

77 FR 32717 - Distribution of Continued Dumping and Subsidy Offset to Affected Domestic Producers

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

...Pursuant to the Continued Dumping and Subsidy Offset Act of 2000, this document is U.S. Customs and Border Protection's notice of intent to distribute assessed antidumping or countervailing duties (known as the continued dumping and subsidy offset) for Fiscal Year 2012 in connection with countervailing duty orders, antidumping duty orders, or findings under the Antidumping Act of 1921. This document sets forth the case name and number of each order or finding for which funds may become available for distribution, together with the list of affected domestic producers, based on the list supplied by the United States International Trade Commission (USITC) associated with each order or finding, who are potentially eligible to receive a distribution. This document also provides the instructions for affected domestic producers (and anyone alleging eligibility to receive a distribution) to file certifications to claim a distribution in relation to the listed orders or findings.

78 FR 32713 - Distribution of Continued Dumping and Subsidy Offset to Affected Domestic Producers

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-31

...Pursuant to the Continued Dumping and Subsidy Offset Act of 2000, this document is U.S. Customs and Border Protection's notice of intent to distribute assessed antidumping or countervailing duties (known as the continued dumping and subsidy offset) for Fiscal Year 2013 in connection with countervailing duty orders, antidumping duty orders, or findings under the Antidumping Act of 1921. This document sets forth the case name and number of each order or finding for which funds may become available for distribution, together with the list of affected domestic producers, based on the list supplied by the United States International Trade Commission (USITC) associated with each order or finding, who are potentially eligible to receive a distribution. This document also provides the instructions for affected domestic producers (and anyone alleging eligibility to receive a distribution) to file certifications to claim a distribution in relation to the listed orders or findings.

THE NATURE OF ACTIVE GALACTIC NUCLEI WITH VELOCITY OFFSET EMISSION LINES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Müller-Sánchez, F.; Comerford, J.; Stern, D.

We obtained Keck/OSIRIS near-IR adaptive optics-assisted integral-field spectroscopy to probe the morphology and kinematics of the ionized gas in four velocity-offset active galactic nuclei (AGNs) from the Sloan Digital Sky Survey. These objects possess optical emission lines that are offset in velocity from systemic as measured from stellar absorption features. At a resolution of ∼0.″18, OSIRIS allows us to distinguish which velocity offset emission lines are produced by the motion of an AGN in a dual supermassive black hole system, and which are produced by outflows or other kinematic structures. In three galaxies, J1018+2941, J1055+1520, and J1346+5228, the spectral offsetmore » of the emission lines is caused by AGN-driven outflows. In the remaining galaxy, J1117+6140, a counterrotating nuclear disk is observed that contains the peak of Pa α emission 0.″2 from the center of the galaxy. The most plausible explanation for the origin of this spatially and kinematically offset peak is that it is a region of enhanced Pa α emission located at the intersection zone between the nuclear disk and the bar of the galaxy. In all four objects, the peak of ionized gas emission is not spatially coincident with the center of the galaxy as traced by the peak of the near-IR continuum emission. The peaks of ionized gas emission are spatially offset from the galaxy centers by 0.″1–0.″4 (0.1–0.7 kpc). We find that the velocity offset originates at the location of this peak of emission, and the value of the offset can be directly measured in the velocity maps. The emission-line ratios of these four velocity-offset AGNs can be reproduced only with a mixture of shocks and AGN photoionization. Shocks provide a natural explanation for the origin of the spatially and spectrally offset peaks of ionized gas emission in these galaxies.« less

Carrier frequency offset estimation for an acoustic-electric channel using 16 QAM modulation

NASA Astrophysics Data System (ADS)

Cunningham, Michael T.; Anderson, Leonard A.; Wilt, Kyle R.; Chakraborty, Soumya; Saulnier, Gary J.; Scarton, Henry A.

2016-05-01

Acoustic-electric channels can be used to send data through metallic barriers, enabling communications where electromagnetic signals are ineffective. This paper considers an acoustic-electric channel that is formed by mounting piezoelectric transducers on metallic barriers that are separated by a thin water layer. The transducers are coupled to the barriers using epoxy and the barriers are positioned to axially-align the PZTs, maximizing energy transfer efficiency. The electrical signals are converted by the transmitting transducers into acoustic waves, which propagate through the elastic walls and water medium to the receiving transducers. The reverberation of the acoustic signals in these channels can produce multipath distortion with a significant delay spread that introduces inter-symbol interference (ISI) into the received signal. While the multipath effects can be severe, the channel does not change rapidly which makes equalization easier. Here we implement a 16-QAM system on this channel, including a method for obtaining accurate carrier frequency offset (CFO) estimates in the presence of the quasi-static multipath propagation. A raised-power approach is considered but found to suffer from excessive data noise resulting from the ISI. An alternative approach that utilizes a pilot tone burst at the start of a data packet is used for CFO estimation and found to be effective. The autocorrelation method is used to estimate the frequency of the received burst. A real-time prototype of the 16 QAM system that uses a Texas Instruments MSP430 microcontroller-based transmitter and a personal computer-based receiver is presented along with performance results.

Real-time estimation of BDS/GPS high-rate satellite clock offsets using sequential least squares

NASA Astrophysics Data System (ADS)

Fu, Wenju; Yang, Yuanxi; Zhang, Qin; Huang, Guanwen

2018-07-01

The real-time precise satellite clock product is one of key prerequisites for real-time Precise Point Positioning (PPP). The accuracy of the 24-hour predicted satellite clock product with 15 min sampling interval and an update of 6 h provided by the International GNSS Service (IGS) is only 3 ns, which could not meet the needs of all real-time PPP applications. The real-time estimation of high-rate satellite clock offsets is an efficient method for improving the accuracy. In this paper, the sequential least squares method to estimate real-time satellite clock offsets with high sample rate is proposed to improve the computational speed by applying an optimized sparse matrix operation to compute the normal equation and using special measures to take full advantage of modern computer power. The method is first applied to BeiDou Navigation Satellite System (BDS) and provides real-time estimation with a 1 s sample rate. The results show that the amount of time taken to process a single epoch is about 0.12 s using 28 stations. The Standard Deviation (STD) and Root Mean Square (RMS) of the real-time estimated BDS satellite clock offsets are 0.17 ns and 0.44 ns respectively when compared to German Research Center for Geosciences (GFZ) final clock products. The positioning performance of the real-time estimated satellite clock offsets is evaluated. The RMSs of the real-time BDS kinematic PPP in east, north, and vertical components are 7.6 cm, 6.4 cm and 19.6 cm respectively. The method is also applied to Global Positioning System (GPS) with a 10 s sample rate and the computational time of most epochs is less than 1.5 s with 75 stations. The STD and RMS of the real-time estimated GPS satellite clocks are 0.11 ns and 0.27 ns, respectively. The accuracies of 5.6 cm, 2.6 cm and 7.9 cm in east, north, and vertical components are achieved for the real-time GPS kinematic PPP.

Improved argument-FFT frequency offset estimation for QPSK coherent optical Systems

NASA Astrophysics Data System (ADS)

Han, Jilong; Li, Wei; Yuan, Zhilin; Li, Haitao; Huang, Liyan; Hu, Qianggao

2016-02-01

A frequency offset estimation (FOE) algorithm based on fast Fourier transform (FFT) of the signal's argument is investigated, which does not require removing the modulated data phase. In this paper, we analyze the flaw of the argument-FFT algorithm and propose a combined FOE algorithm, in which the absolute of frequency offset (FO) is accurately calculated by argument-FFT algorithm with a relatively large number of samples and the sign of FO is determined by FFT-based interpolation discrete Fourier transformation (DFT) algorithm with a relatively small number of samples. Compared with the previous algorithms based on argument-FFT, the proposed one has low complexity and can still effectively work with a relatively less number of samples.

Precise Receiver Clock Offset Estimations According to Each Global Navigation Satellite Systems (GNSS) Timescales

NASA Astrophysics Data System (ADS)

Thongtan, Thayathip; Tirawanichakul, Pawit; Satirapod, Chalermchon

2017-12-01

Each GNSS constellation operates its own system times; namely, GPS system time (GPST), GLONASS system time (GLONASST), BeiDou system time (BDT) and Galileo system time (GST). They could be traced back to Coordinated Universal Time (UTC) scale and are aligned to GPST. This paper estimates the receiver clock offsets to three timescales: GPST, GLONASST and BDT. The two measurement scenarios use two identical multi-GNSS geodetic receivers connected to the same geodetic antenna through a splitter. One receiver is driven by its internal oscillators and another receiver is connected to the external frequency oscillators, caesium frequency standard, kept as the Thailand standard time scale at the National Institute of Metrology (Thailand) called UTC(NIMT). The three weeks data are observed at 30 seconds sample rate. The receiver clock offsets with respected to the three system time are estimated and analysed through the geodetic technique of static Precise Point Positioning (PPP) using a data processing software developed by Wuhan University - Positioning And Navigation Data Analyst (PANDA) software. The estimated receiver clock offsets are around 32, 33 and 18 nanoseconds from GPST, GLONASST and BDT respectively. This experiment is initially stated that each timescale is inter-operated with GPST and further measurements on receiver internal delay has to be determined for clock comparisons especially the high accuracy clock at timing laboratories.

Glacier surface velocity estimation in the West Kunlun Mountain range from L-band ALOS/PALSAR images using modified synthetic aperture radar offset-tracking procedure

NASA Astrophysics Data System (ADS)

Ruan, Zhixing; Guo, Huadong; Liu, Guang; Yan, Shiyong

2014-01-01

Glacier movement is closely related to changes in climatic, hydrological, and geological factors. However, detecting glacier surface flow velocity with conventional ground surveys is challenging. Remote sensing techniques, especially synthetic aperture radar (SAR), provide regular observations covering larger-scale glacier regions. Glacier surface flow velocity in the West Kunlun Mountains using modified offset-tracking techniques based on ALOS/PALSAR images is estimated. Three maps of glacier flow velocity for the period 2007 to 2010 are derived from procedures of offset detection using cross correlation in the Fourier domain and global offset elimination of thin plate smooth splines. Our results indicate that, on average, winter glacier motion on the North Slope is 1 cm/day faster than on the South Slope-a result which corresponds well with the local topography. The performance of our method as regards the reliability of extracted displacements and the robustness of this algorithm are discussed. The SAR-based offset tracking is proven to be reliable and robust, making it possible to investigate comprehensive glacier movement and its response mechanism to environmental change.

A currency for offsetting energy development impacts: horse-trading sage-grouse on the open market.

PubMed

Doherty, Kevin E; Naugle, David E; Evans, Jeffrey S

2010-04-28

Biodiversity offsets provide a mechanism to compensate for unavoidable damages from new energy development as the U.S. increases its domestic production. Proponents argue that offsets provide a partial solution for funding conservation while opponents contend the practice is flawed because offsets are negotiated without the science necessary to backup resulting decisions. Missing in negotiations is a biologically-based currency for estimating sufficiency of offsets and a framework for applying proceeds to maximize conservation benefits. Here we quantify a common currency for offsets for greater sage-grouse (Centrocercus urophasianus) by estimating number of impacted birds at 4 levels of development commonly permitted. Impacts were indiscernible at 1-12 wells per 32.2 km(2). Above this threshold lek losses were 2-5 times greater inside than outside of development and bird abundance at remaining leks declined by -32 to -77%. Findings reiterated the importance of time-lags as evidenced by greater impacts 4 years after initial development. Clustering well locations enabled a few small leks to remain active inside of developments. Documented impacts relative to development intensity can be used to forecast biological trade-offs of newly proposed or ongoing developments, and when drilling is approved, anticipated bird declines form the biological currency for negotiating offsets. Monetary costs for offsets will be determined by true conservation cost to mitigate risks such as sagebrush tillage to other populations of equal or greater number. If this information is blended with landscape level conservation planning, the mitigation hierarchy can be improved by steering planned developments away from conservation priorities, ensuring compensatory mitigation projects deliver a higher return for conservation that equate to an equal number of birds in the highest priority areas, provide on-site mitigation recommendations, and provide a biologically based cost for mitigating unavoidable impacts.

A Range Correction for Icesat and Its Potential Impact on Ice-sheet Mass Balance Studies

NASA Technical Reports Server (NTRS)

Borsa, A. A.; Moholdt, G.; Fricker, H. A.; Brunt, Kelly M.

2014-01-01

We report on a previously undocumented range error in NASA's Ice, Cloud and land Elevation Satellite (ICESat) that degrades elevation precision and introduces a small but significant elevation trend over the ICESat mission period. This range error (the Gaussian-Centroid or 'G-C'offset) varies on a shot-to-shot basis and exhibits increasing scatter when laser transmit energies fall below 20 mJ. Although the G-C offset is uncorrelated over periods less than1 day, it evolves over the life of each of ICESat's three lasers in a series of ramps and jumps that give rise to spurious elevation trends of -0.92 to -1.90 cm yr(exp -1), depending on the time period considered. Using ICESat data over the Ross and Filchner-Ronne ice shelves we show that (1) the G-C offset introduces significant biases in ice-shelf mass balance estimates, and (2) the mass balance bias can vary between regions because of different temporal samplings of ICESat.We can reproduce the effect of the G-C offset over these two ice shelves by fitting trends to sample-weighted mean G-C offsets for each campaign, suggesting that it may not be necessary to fully repeat earlier ICESat studies to determine the impact of the G-C offset on ice-sheet mass balance estimates.

Image formation in microwave holography

NASA Technical Reports Server (NTRS)

Cribbs, R. W.; Lamb, B. L.

1973-01-01

Microwave holograms are made without offset reference beam, but it has been found that Van der Lugt filter can be used to produce image offset. Also, filter permits "decoding" of holograms in contrast with usual practice of reconstructing visible-light analogs of original micro-wave wave fronts.

Uncertainties in slip-rate estimates for the Mission Creek strand of the southern San Andreas fault at Biskra Palms Oasis, southern California

USGS Publications Warehouse

Behr, W.M.; Rood, D.H.; Fletcher, K.E.; Guzman, N.; Finkel, R.; Hanks, T.C.; Hudnut, K.W.; Kendrick, K.J.; Platt, J.P.; Sharp, W.D.; Weldon, R.J.; Yule, J.D.

2010-01-01

This study focuses on uncertainties in estimates of the geologic slip rate along the Mission Creek strand of the southern San Andreas fault where it offsets an alluvial fan (T2) at Biskra Palms Oasis in southern California. We provide new estimates of the amount of fault offset of the T2 fan based on trench excavations and new cosmogenic 10Be age determinations from the tops of 12 boulders on the fan surface. We present three alternative fan offset models: a minimum, a maximum, and a preferred offset of 660 m, 980 m, and 770 m, respectively. We assign an age of between 45 and 54 ka to the T2 fan from the 10Be data, which is significantly older than previously reported but is consistent with both the degree of soil development associated with this surface, and with ages from U-series geochronology on pedogenic carbonate from T2, described in a companion paper by Fletcher et al. (this volume). These new constraints suggest a range of slip rates between ~12 and 22 mm/yr with a preferred estimate of ~14-17 mm/yr for the Mission Creek strand of the southern San Andreas fault. Previous studies suggested that the geologic and geodetic slip-rate estimates at Biskra Palms differed. We find, however, that considerable uncertainty affects both the geologic and geodetic slip-rate estimates, such that if a real discrepancy between these rates exists for the southern San Andreas fault at Biskra Palms, it cannot be demonstrated with available data. ?? 2010 Geological Society of America.

AN EXPERIMENTAL INVESTIGATION OF MICROPRINGING BY THE OFFSET METHOD, SUPPLEMENT.

DTIC Science & Technology

samples produced clearly indicated that the limitation of the offset method had not been reached for lexical material. However, the halftones printed at...more line art and fewer halftones . This preference and trend will favor microprinting by making greater reduction practical, and is another reason

Flight Test Results for the Motions and Aerodynamics of a Cargo Container and a Cylindrical Slung Load

DTIC Science & Technology

2010-04-01

cylinders is suspected to account for the lateral offset. A simple model of the Magnus effect (ref. 23) indicates that it generates force per...The spin also produced a small but measurable Magnus effect . An extreme cg offset produced stability around small end into the wind. The engine...expected. If we assume the flight data for cable angles are accurate to a fraction of a degree, then a Magnus effect similar to that found for spinning

Application of Kalman filter in frequency offset estimation for coherent optical quadrature phase-shift keying communication system

NASA Astrophysics Data System (ADS)

Jiang, Wen; Yang, Yanfu; Zhang, Qun; Sun, Yunxu; Zhong, Kangping; Zhou, Xian; Yao, Yong

2016-09-01

The frequency offset estimation (FOE) schemes based on Kalman filter are proposed and investigated in detail via numerical simulation and experiment. The schemes consist of a modulation phase removing stage and Kalman filter estimation stage. In the second stage, the Kalman filters are employed for tracking either differential angles or differential data between two successive symbols. Several implementations of the proposed FOE scheme are compared by employing different modulation removing methods and two Kalman algorithms. The optimal FOE implementation is suggested for different operating conditions including optical signal-to-noise ratio and the number of the available data symbols.

An Analysis of Second-Tier Arms Producing Countries’ Offset Policies: Technology Transfer and Defense Industrial Base Establishment

DTIC Science & Technology

2008-03-01

38  39  ......................... 40  ......................... 42  42  Offsets in the Global Arms Market ...The Global Arms Market Structure .................................................. Increasing Globalization of Defense Industry...109  Overcapacity of the Defense Industry in a Declining Market ........................... 109 Economies of Scale

Phonation Offset in Tracheoesophageal Speech

ERIC Educational Resources Information Center

Searl, Jeff; Ousley, Teri

2004-01-01

Tracheoesophageal (TE) speakers often have difficulty producing the voiced-voiceless distinction. Phonation offset (POff) as a TE speaker transitions from a vowel to a stop consonant may be altered, possibly contributing to listener misperceptions. The purposes of this study were to: (1) compare the duration of POff in TE versus laryngeal…

Getting the numbers right: revisiting woodfuel sustainability in the developing world

NASA Astrophysics Data System (ADS)

Bailis, Rob; Wang, Yiting; Drigo, Rudi; Ghilardi, Adrian; Masera, Omar

2017-11-01

The United Nations’ Sustainable Development Goals encourage a transition to ‘affordable, reliable, sustainable and modern energy for all’. To be successful, the transition requires billions of people to adopt cleaner, more efficient cooking technologies that contribute to sustainability through multiple pathways: improved air quality, reduced emissions of short-lived climate pollutants, and reduced deforestation or forest degradation. However, the latter depends entirely on the extent to which people rely on ‘non-renewable biomass’ (NRB). This paper compares NRB estimates from 286 carbon-offset projects in 51 countries to a recently published spatial assessment of pan-tropical woodfuel demand and supply. The existing projects expect to produce offsets equivalent to ~138 MtCO2e. However, when we apply NRB values derived from spatially explicit woodfuel demand and supply imbalances in the region of each offset project, we find that emission reductions are between 57 and 81 MtCO2e: 41%-59% lower than expected. We suggest that project developers and financiers recalibrate their expectations of the mitigation potential of woodfuel projects. Spatial approaches like the one utilized here indicate regions where interventions are more (and less) likely to reduce deforestation or degradation: for example, in woodfuel ‘hotspots’ in East, West, and Southern Africa as well as South Asia, where nearly 300 million people live with acute woodfuel scarcity.

Comments on potential geologic and seismic hazards affecting coastal Ventura County, California

USGS Publications Warehouse

Ross, Stephanie L.; Boore, David M.; Fisher, Michael A.; Frankel, Arthur D.; Geist, Eric L.; Hudnut, Kenneth W.; Kayen, Robert E.; Lee, Homa J.; Normark, William R.; Wong, Florence L.

2004-01-01

This report examines the regional seismic and geologic hazards that could affect proposed liquefied natural gas (LNG) facilities in coastal Ventura County, California. Faults throughout this area are thought to be capable of producing earthquakes of magnitude 6.5 to 7.5, which could produce surface fault offsets of as much as 15 feet. Many of these faults are sufficiently well understood to be included in the current generation of the National Seismic Hazard Maps; others may become candidates for inclusion in future revisions as research proceeds. Strong shaking is the primary hazard that causes damage from earthquakes and this area is zoned with a high level of shaking hazard. The estimated probability of a magnitude 6.5 or larger earthquake (comparable in size to the 2003 San Simeon quake) occurring in the next 30 years within 30 miles of Platform Grace is 50-60%; for Cabrillo Port, the estimate is a 35% likelihood. Combining these probabilities of earthquake occurrence with relationships that give expected ground motions yields the estimated seismic-shaking hazard. In parts of the project area, the estimated shaking hazard is as high as along the San Andreas Fault. The combination of long-period basin waves and LNG installations with large long-period resonances potentially increases this hazard.

A mathematical model of diurnal variations in human plasma melatonin levels

NASA Technical Reports Server (NTRS)

Brown, E. N.; Choe, Y.; Shanahan, T. L.; Czeisler, C. A.

1997-01-01

Studies in animals and humans suggest that the diurnal pattern in plasma melatonin levels is due to the hormone's rates of synthesis, circulatory infusion and clearance, circadian control of synthesis onset and offset, environmental lighting conditions, and error in the melatonin immunoassay. A two-dimensional linear differential equation model of the hormone is formulated and is used to analyze plasma melatonin levels in 18 normal healthy male subjects during a constant routine. Recently developed Bayesian statistical procedures are used to incorporate correctly the magnitude of the immunoassay error into the analysis. The estimated parameters [median (range)] were clearance half-life of 23.67 (14.79-59.93) min, synthesis onset time of 2206 (1940-0029), synthesis offset time of 0621 (0246-0817), and maximum N-acetyltransferase activity of 7.17(2.34-17.93) pmol x l(-1) x min(-1). All were in good agreement with values from previous reports. The difference between synthesis offset time and the phase of the core temperature minimum was 1 h 15 min (-4 h 38 min-2 h 43 min). The correlation between synthesis onset and the dim light melatonin onset was 0.93. Our model provides a more physiologically plausible estimate of the melatonin synthesis onset time than that given by the dim light melatonin onset and the first reliable means of estimating the phase of synthesis offset. Our analysis shows that the circadian and pharmacokinetics parameters of melatonin can be reliably estimated from a single model.

Offsets between the X-ray and the Sunyaev-Zel'Dovich-effect peaks in merging galaxy clusters and their cosmological implications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Congyao; Yu, Qingjuan; Lu, Youjun, E-mail: yuqj@pku.edu.cn

2014-12-01

Observations reveal that the peaks of the X-ray map and the Sunyaev-Zel'dovich (SZ) effect map of some galaxy clusters are offset from each other. In this paper, we perform a set of hydrodynamical simulations of mergers of two galaxy clusters to investigate the spatial offset between the maxima of the X-ray and the SZ surface brightness of the merging clusters. We find that significantly large SZ-X-ray offsets (>100 kpc) can be produced during the major mergers of galaxy clusters (with mass > 1 × 10{sup 14} M {sub ☉}). The significantly large offsets are mainly caused by a 'jump effect'more » that occurs between the primary and secondary pericentric passages of the two merging clusters, during which the X-ray peak may jump to the densest gas region located near the center of the small cluster, but the SZ peak remains near the center of the large one. Our simulations show that merging systems with higher masses and larger initial relative velocities may result in larger offset sizes and longer offset time durations; and only nearly head-on mergers are likely to produce significantly large offsets. We further investigate the statistical distribution of the SZ-X-ray offset sizes and find that (1) the number distribution of the offset sizes is bimodal with one peak located at low offsets ∼0 and the other at large offsets ∼350-450 h {sup –1} kpc, but the objects with intermediate offsets are scarce; and (2) the probabilities of the clusters in the mass range higher than 2 × 10{sup 14} h {sup –1} M {sub ☉} that have offsets larger than 20, 50, 200, 300, and 500 h {sup –1} kpc are 34.0%, 11.1%, 8.0%, 6.5%, and 2.0%, respectively, at z = 0.7. The probability is sensitive to the underlying pairwise velocity distribution and the merger rate of clusters. We suggest that the SZ-X-ray offsets provide a probe to the cosmic velocity fields on the cluster scale and the cluster merger rate, and future observations on the SZ-X-ray offsets for a large number of clusters may put strong constraints on them. Our simulation results suggest that the SZ-X-ray offset in the Bullet Cluster, together with the mass ratio of the two merging clusters, requires a relative velocity larger than 3000 km s{sup –1} at an initial separation 5 Mpc. The cosmic velocity distribution at the high-velocity end is expected to be crucial in determining whether there exists an incompatibility between the existence of the Bullet Cluster and the prediction of a ΛCDM model.« less

Late Holocene activity of the Dead Sea Transform revealed in 3D palaeoseismic trenches on the Jordan Gorge segment [rapid communication

NASA Astrophysics Data System (ADS)

Marco, Shmuel; Rockwell, Thomas K.; Heimann, Ariel; Frieslander, Uri; Agnon, Amotz

2005-05-01

Three-dimensional excavations of buried stream channels that have been displaced by the Jordan Fault, the primary strand of the Dead Sea fault zone in northern Israel, demonstrate that late Holocene slip has been primarily strike-slip at a minimum rate of 3 mm/yr. The palaeoseismic study was carried out in the Bet-Zayda Valley, the delta of the Jordan River at the north shore of the Sea of Galilee. The site was chosen where a north-striking scarp with up to 1-m vertical expression crosses the flat valley. One group of trench excavations was located where a small stream crosses the scarp. The active stream, which is incised into the scarp, is not offset by the fault. However we found two palaeo channels about 2 m below the surface offset sinistrally 2.7±0.2 m by the fault and two younger nested channels offset 0.5±0.05 m. Based on radiocarbon dates we attribute the last 0.5 m rupture to the earthquake of October 30, 1759. The older offset of 2.2 m most probably occurred in the earthquakes of May 20, 1202. These two events correlate with the findings at Ateret, about 12 km north of Bet-Zayda, where the 1202 earthquake produced 1.6 m of lateral displacement in E-W-striking defence walls of a Crusader castle, and an Ottoman mosque was offset 0.5 m in the earthquake of 1759. In the second group of trenches some 60 m farther south we found another offset channel. Its northern margin is displaced 15 m sinistrally whereas the southern margin shows only 9 m of sinistral offset. The dip slip component is 1.2 m, west side down. The different amounts of margin offset can be explained by erosion of the southern margin during the first 6 m of displacement. Additional slip of 9 m accrued after the stream had been abandoned and buried by a 2-m-thick lacustrine clay layers. Radiocarbon dates on organic residue provide the age control which indicates that the 15 m of slip has accrued over the past 5 kyr, yielding a short-term slip rate of 3 mm/yr for the late Holocene. It is possible that our study covers only part of the fault zone, hence we regard this mean slip rate to be a minimum for the DST. Based on other palaeoseismic studies the best estimate for Quaternary slip rate is 4±1 mm/yr.

Methane emissions partially offset “blue carbon” burial in mangroves

PubMed Central

Maher, Damien T.

2018-01-01

Organic matter burial in mangrove forests results in the removal and long-term storage of atmospheric CO2, so-called “blue carbon.” However, some of this organic matter is metabolized and returned to the atmosphere as CH4. Because CH4 has a higher global warming potential than the CO2 fixed in the organic matter, it can offset the CO2 removed via carbon burial. We provide the first estimate of the global magnitude of this offset. Our results show that high CH4 evasion rates have the potential to partially offset blue carbon burial rates in mangrove sediments on average by 20% (sensitivity analysis offset range, 18 to 22%) using the 20-year global warming potential. Hence, mangrove sediment and water CH4 emissions should be accounted for in future blue carbon assessments.

High-resolution 14C dating of a 25,000-year lake-sediment record from equatorial East Africa

NASA Astrophysics Data System (ADS)

Blaauw, Maarten; van Geel, Bas; Kristen, Iris; Plessen, Birgit; Lyaruu, Anna; Engstrom, Daniel R.; van der Plicht, Johannes; Verschuren, Dirk

2011-10-01

We dated a continuous, ˜22-m long sediment sequence from Lake Challa (Mt. Kilimanjaro area, Kenya/Tanzania) to produce a solid chronological framework for multi-proxy reconstructions of climate and environmental change in equatorial East Africa over the past 25,000 years. The age model is based on a total of 168 AMS 14C dates on bulk-organic matter, combined with a 210Pb chronology for recent sediments and corrected for a variable old-carbon age offset. This offset was estimated by i) pairing bulk-organic 14C dates with either 210Pb-derived time markers or 14C dates on grass charcoal, and ii) wiggle-matching high-density series of bulk-organic 14C dates. Variation in the old-carbon age offset through time is relatively modest, ranging from ˜450 yr during glacial and late glacial time to ˜200 yr during the early and mid-Holocene, and increasing again to ˜250 yr today. The screened and corrected 14C dates were calibrated sequentially, statistically constrained by their stratigraphical order. As a result their constrained calendar-age distributions are much narrower, and the calibrated dates more precise, than if each 14C date had been calibrated on its own. The smooth-spline age-depth model has 95% age uncertainty ranges of ˜50-230 yr during the Holocene and ˜250-550 yr in the glacial section of the record. The δ 13C values of paired bulk-organic and grass-charcoal samples, and additional 14C dating on selected turbidite horizons, indicates that the old-carbon age offset in Lake Challa is caused by a variable contribution of old terrestrial organic matter eroded from soils, and controlled mainly by changes in vegetation cover within the crater basin.

Cost analysis of impacts of climate change on regional air quality.

PubMed

Liao, Kuo-Jen; Tagaris, Efthimios; Russell, Armistead G; Amar, Praveen; He, Shan; Manomaiphiboon, Kasemsan; Woo, Jung-Hun

2010-02-01

Climate change has been predicted to adversely impact regional air quality with resulting health effects. Here a regional air quality model and a technology analysis tool are used to assess the additional emission reductions required and associated costs to offset impacts of climate change on air quality. Analysis is done for six regions and five major cities in the continental United States. Future climate is taken from a global climate model simulation for 2049-2051 using the Intergovernmental Panel on Climate Change (IPCC) A1B emission scenario, and emission inventories are the same as current ones to assess impacts of climate change alone on air quality and control expenses. On the basis of the IPCC A1B emission scenario and current control technologies, least-cost sets of emission reductions for simultaneously offsetting impacts of climate change on regionally averaged 4th highest daily maximum 8-hr average ozone and yearly averaged PM2.5 (particulate matter [PM] with an aerodynamic diameter less than 2.5 microm) for the six regions examined are predicted to range from $36 million (1999$) yr(-1) in the Southeast to $5.5 billion yr(-1) in the Northeast. However, control costs to offset climate-related pollutant increases in urban areas can be greater than the regional costs because of the locally exacerbated ozone levels. An annual cost of $4.1 billion is required for offsetting climate-induced air quality impairment in 2049-2051 in the five cities alone. Overall, an annual cost of $9.3 billion is estimated for offsetting climate change impacts on air quality for the six regions and five cities examined. Much of the additional expense is to reduce increased levels of ozone. Additional control costs for offsetting the impacts everywhere in the United States could be larger than the estimates in this study. This study shows that additional emission controls and associated costs for offsetting climate impacts could significantly increase currently estimated control requirements and should be considered in developing control strategies for achieving air quality targets in the future.

Joint Symbol Timing and CFO Estimation for OFDM/OQAM Systems in Multipath Channels

NASA Astrophysics Data System (ADS)

Fusco, Tilde; Petrella, Angelo; Tanda, Mario

2009-12-01

The problem of data-aided synchronization for orthogonal frequency division multiplexing (OFDM) systems based on offset quadrature amplitude modulation (OQAM) in multipath channels is considered. In particular, the joint maximum-likelihood (ML) estimator for carrier-frequency offset (CFO), amplitudes, phases, and delays, exploiting a short known preamble, is derived. The ML estimators for phases and amplitudes are in closed form. Moreover, under the assumption that the CFO is sufficiently small, a closed form approximate ML (AML) CFO estimator is obtained. By exploiting the obtained closed form solutions a cost function whose peaks provide an estimate of the delays is derived. In particular, the symbol timing (i.e., the delay of the first multipath component) is obtained by considering the smallest estimated delay. The performance of the proposed joint AML estimator is assessed via computer simulations and compared with that achieved by the joint AML estimator designed for AWGN channel and that achieved by a previously derived joint estimator for OFDM systems.

The Nature of Active Galactic Nuclei with Velocity Offset Emission Lines

NASA Astrophysics Data System (ADS)

Müller-Sánchez, F.; Comerford, J.; Stern, D.; Harrison, F. A.

2016-10-01

We obtained Keck/OSIRIS near-IR adaptive optics-assisted integral-field spectroscopy to probe the morphology and kinematics of the ionized gas in four velocity-offset active galactic nuclei (AGNs) from the Sloan Digital Sky Survey. These objects possess optical emission lines that are offset in velocity from systemic as measured from stellar absorption features. At a resolution of ˜0.″18, OSIRIS allows us to distinguish which velocity offset emission lines are produced by the motion of an AGN in a dual supermassive black hole system, and which are produced by outflows or other kinematic structures. In three galaxies, J1018+2941, J1055+1520, and J1346+5228, the spectral offset of the emission lines is caused by AGN-driven outflows. In the remaining galaxy, J1117+6140, a counterrotating nuclear disk is observed that contains the peak of Paα emission 0.″2 from the center of the galaxy. The most plausible explanation for the origin of this spatially and kinematically offset peak is that it is a region of enhanced Paα emission located at the intersection zone between the nuclear disk and the bar of the galaxy. In all four objects, the peak of ionized gas emission is not spatially coincident with the center of the galaxy as traced by the peak of the near-IR continuum emission. The peaks of ionized gas emission are spatially offset from the galaxy centers by 0.″1-0.″4 (0.1-0.7 kpc). We find that the velocity offset originates at the location of this peak of emission, and the value of the offset can be directly measured in the velocity maps. The emission-line ratios of these four velocity-offset AGNs can be reproduced only with a mixture of shocks and AGN photoionization. Shocks provide a natural explanation for the origin of the spatially and spectrally offset peaks of ionized gas emission in these galaxies. Based on observations at the W. M. Keck Observatory, which is operated as a scientific partnership among the California Institute of Technology, the University of California and the National Aeronautics and Space Administration. The Observatory was made possible by the generous financial support of the W. M. Keck Foundation.

The Effect of Temporal Perception on Weight Perception

PubMed Central

Kambara, Hiroyuki; Shin, Duk; Kawase, Toshihiro; Yoshimura, Natsue; Akahane, Katsuhito; Sato, Makoto; Koike, Yasuharu

2013-01-01

A successful catch of a falling ball requires an accurate estimation of the timing for when the ball hits the hand. In a previous experiment in which participants performed ball-catching task in virtual reality environment, we accidentally found that the weight of a falling ball was perceived differently when the timing of ball load force to the hand was shifted from the timing expected from visual information. Although it is well known that spatial information of an object, such as size, can easily deceive our perception of its heaviness, the relationship between temporal information and perceived heaviness is still not clear. In this study, we investigated the effect of temporal factors on weight perception. We conducted ball-catching experiments in a virtual environment where the timing of load force exertion was shifted away from the visual contact timing (i.e., time when the ball hit the hand in the display). We found that the ball was perceived heavier when force was applied earlier than visual contact and lighter when force was applied after visual contact. We also conducted additional experiments in which participants were conditioned to one of two constant time offsets prior to testing weight perception. After performing ball-catching trials with 60 ms advanced or delayed load force exertion, participants’ subjective judgment on the simultaneity of visual contact and force exertion changed, reflecting a shift in perception of time offset. In addition, timing of catching motion initiation relative to visual contact changed, reflecting a shift in estimation of force timing. We also found that participants began to perceive the ball as lighter after conditioning to 60 ms advanced offset and heavier after the 60 ms delayed offset. These results suggest that perceived heaviness depends not on the actual time offset between force exertion and visual contact but on the subjectively perceived time offset between them and/or estimation error in force timing. PMID:23450805

A Currency for Offsetting Energy Development Impacts: Horse-Trading Sage-Grouse on the Open Market

PubMed Central

Doherty, Kevin E.; Naugle, David E.; Evans, Jeffrey S.

2010-01-01

Background Biodiversity offsets provide a mechanism to compensate for unavoidable damages from new energy development as the U.S. increases its domestic production. Proponents argue that offsets provide a partial solution for funding conservation while opponents contend the practice is flawed because offsets are negotiated without the science necessary to backup resulting decisions. Missing in negotiations is a biologically-based currency for estimating sufficiency of offsets and a framework for applying proceeds to maximize conservation benefits. Methodology/Principal Findings Here we quantify a common currency for offsets for greater sage-grouse (Centrocercus urophasianus) by estimating number of impacted birds at 4 levels of development commonly permitted. Impacts were indiscernible at 1–12 wells per 32.2 km2. Above this threshold lek losses were 2–5 times greater inside than outside of development and bird abundance at remaining leks declined by −32 to −77%. Findings reiterated the importance of time-lags as evidenced by greater impacts 4 years after initial development. Clustering well locations enabled a few small leks to remain active inside of developments. Conclusions/Significance Documented impacts relative to development intensity can be used to forecast biological trade-offs of newly proposed or ongoing developments, and when drilling is approved, anticipated bird declines form the biological currency for negotiating offsets. Monetary costs for offsets will be determined by true conservation cost to mitigate risks such as sagebrush tillage to other populations of equal or greater number. If this information is blended with landscape level conservation planning, the mitigation hierarchy can be improved by steering planned developments away from conservation priorities, ensuring compensatory mitigation projects deliver a higher return for conservation that equate to an equal number of birds in the highest priority areas, provide on-site mitigation recommendations, and provide a biologically based cost for mitigating unavoidable impacts. PMID:20442770

Estimating the value of electricity storage in PJM: Arbitrage and some welfare effects

DOE PAGES

Sioshansi, Ramteen; Denholm, Paul; Jenkin, Thomas; ...

2008-10-31

Here, significant increases in prices and price volatility of natural gas and electricity have raised interest in the potential economic opportunities for electricity storage. In this paper, we analyze the arbitrage value of a price-taking storage device in PJM during the six-year period from 2002 to 2007, to understand the impact of fuel prices, transmission constraints, efficiency, storage capacity, and fuel mix. The impact of load-shifting for larger amounts of storage, where reductions in arbitrage are offset by shifts in consumer and producer surplus as well as increases in social welfare from a variety of sources, is also considered.

Galileo orbit determination for the Venus and Earth-1 flybys

NASA Astrophysics Data System (ADS)

Kallemeyn, P. H.; Haw, R. J.; Pollmeier, V. M.; Nicholson, F. T.; Murrow, D. W.

1992-08-01

This paper presents the orbit determination strategy and results in navigating the Galileo spacecraft from launch through its Venus and first earth flybys. Many nongravitational effects were estimated, including solar radiation pressure, small velocity impulses from attitude changes and eight trajectory correction maneuvers. Tracking data consisted of S-Band Doppler and range. The fitting of Doppler was difficult since one of the cpacecraft's two antennas was offset from the spin axis, thus producing the sinusoidal velocity fluctuation seen in the data. Finally, Delta Differential One-way Range data was used during the last three months of the earth approach to help deliver the spacecraft to within desired accuracy.

Tunable, Highly Stable Lasers for Coherent Lidar

NASA Technical Reports Server (NTRS)

Henderson, Sammy W.; Hale, Charley P.; EEpagnier, David M.

2006-01-01

Practical space-based coherent laser radar systems envisioned for global winds measurement must be very efficient and must contend with unique problems associated with the large platform velocities that the instruments experience in orbit. To compensate for these large platform-induced Doppler shifts in space-based applications, agile-frequency offset-locking of two single-frequency Doppler reference lasers was thoroughly investigated. Such techniques involve actively locking a frequency-agile master oscillator (MO) source to a comparatively static local oscillator (LO) laser, and effectively producing an offset between MO (the lidar slave oscillator seed source, typically) and heterodyne signal receiver LO that lowers the bandwidth of the receiver data-collection system and permits use of very high-quantum-efficiency, reasonably- low-bandwidth heterodyne photoreceiver detectors and circuits. Recent work on MO/LO offset locking has focused on increasing the offset locking range, improving the graded-InGaAs photoreceiver performance, and advancing the maturity of the offset locking electronics. A figure provides a schematic diagram of the offset-locking system.

Study of weld offset in longitudinally welded SSME HPFTP inlet

NASA Technical Reports Server (NTRS)

Min, J. B.; Spanyer, K. S.; Brunair, R. M.

1992-01-01

Welded joints are an essential part of rocket engine structures such as the Space Shuttle Main Engine (SSME) turbopumps. Defects produced in the welding process can be detrimental to weld performance. Recently, review of the SSME high pressure fuel turbopump (HPFTP) titanium inlet X-rays revealed several weld discrepancies such as penetrameter density issues, film processing discrepancies, weld width discrepancies, porosity, lack of fusion, and weld offsets. Currently, the sensitivity of welded structures to defects is of concern. From a fatigue standpoint, weld offset may have a serious effect since local yielding, in general, aggravates cyclic stress effects. Therefore, the weld offset issue is considered in this report. Using the FEM and beamlike plate approximations, parametric studies were conducted to determine the influence of weld offsets and a variation of weld widths in longitudinally welded cylindrical structures with equal wall thicknesses on both sides of the joint. Following the study, some conclusions are derived for the weld offsets.

The effect of offset on fracture permeability of rocks from the Southern Andes Volcanic Zone, Chile

NASA Astrophysics Data System (ADS)

Pérez-Flores, P.; Wang, G.; Mitchell, T. M.; Meredith, P. G.; Nara, Y.; Sarkar, V.; Cembrano, J.

2017-11-01

The Southern Andes Volcanic Zone (SVZ) represents one of the largest undeveloped geothermal provinces in the world. Development of the geothermal potential requires a detailed understanding of fluid transport properties of its main lithologies. The permeability of SVZ rocks is altered by the presence of fracture damage zones produced by the Liquiñe-Ofqui Fault System (LOFS) and the Andean Transverse Faults (ATF). We have therefore measured the permeability of four representative lithologies from the volcanic basement in this area: crystalline tuff, andesitic dike, altered andesite and granodiorite. For comparative purposes, we have also measured the permeability of samples of Seljadalur basalt, an Icelandic rock with widely studied and reported hydraulic properties. Specifically, we present the results of a systematic study of the effect of fractures and fracture offsets on permeability as a function of increasing effective pressure. Baseline measurements on intact samples of SVZ rocks show that the granodiorite has a permeability (10-18 m2), two orders of magnitude higher than that of the volcanic rocks (10-20 m2). The presence of throughgoing mated macro-fractures increases permeability by between four and six orders of magnitude, with the highest permeability recorded for the crystalline tuff. Increasing fracture offset to produce unmated fractures results in large increases in permeability up to some characteristic value of offset, beyond which permeability changes only marginally. The increase in permeability with offset appears to depend on fracture roughness and aperture, and these are different for each lithology. Overall, fractured SVZ rocks with finite offsets record permeability values consistent with those commonly found in geothermal reservoirs (>10-16 m2), which potentially allow convective/advective flow to develop. Hence, our results demonstrate that the fracture damage zones developed within the SVZ produce permeable regions, especially within the transtensional NE-striking fault zones, that have major importance for geothermal energy resource potential.

Pair Cascades and Deathlines in Magnetic Fields with Offset Polar Caps

NASA Technical Reports Server (NTRS)

Harding, Alice K.; Muslimov, Alex G.

2012-01-01

We present results of electron-positron pair cascade simulations in a dipole magnetic field whose polar cap is offset from the dipole axis. In such a field geometry, the polar cap is displaced a small fraction of the neutron star radius from the star symmetry axis and the field line radius of curvature is modified. Using the modified parallel electric field near the offset polar cap, we simulate pair cascades to determine the pair deathlines and pair multiplicities as a function of the offset. We find that the pair multiplicity can change dr;unatically with a modest offset, with a significant increase on one side of the polar cap. Lower pair deathlines allow a larger fraction of the pulsar population, that include old and millisecond pulsars, to produce cascades with high multiplicity. The results have some important implications for pulsar particle production, high-energy emission and cosmic-ray contribution.

An intercomparison of the thermal offset for different pyranometers

NASA Astrophysics Data System (ADS)

Sanchez, G.; Cancillo, M. L.; Serrano, A.

2016-07-01

An unprecedented intensive intercomparison campaign focused on the experimental measurement of the thermal offset of pyranometers has been conducted at Badajoz (Spain) with the participation of three main manufacturers. The purpose of this study is to compare the thermal offset of six commercially available pyranometers, being some of them widely used and others recently commercialized. In this campaign, the capping methodology has been used to experimentally measure the daytime thermal offset of the pyranometers. Thus, a short but intense campaign has been conducted in two selected summer days under clear-sky conditions, covering a large range of solar zenith angle, irradiance, and temperature. Along the campaign, a total of 305 capping events have been performed, 61 for each pyranometer. The daytime thermal offset obtained for different pyranometers ranges between 0 and -16.8 W/m2 depending on the environmental conditions, being sometimes notably higher than values estimated indoors by manufacturers. The thermal offset absolute value of all instruments shows a diurnal cycle, increasing from sunrise to central hours of the day and decreasing from midafternoon to sunset. The analysis demonstrates that thermal offset is notably higher and more variable during daytime than during nighttime, requiring specific daytime measurements. Main results emphasize the key role played by wind speed in modulating the thermal offset.

Time lapse (4D) and AVO analysis: A case study of Gullfaks field, Northern North Sea

NASA Astrophysics Data System (ADS)

Umoren, Emmanuel Bassey; George, Nyakno Jimmy

2018-06-01

A 4D seismic or time lapse survey has been used to investigate the amplitude versus offset (AVO) effects on seismic data in order to identify anomalies in the Gullfaks field for three different reservoir intervals namely the Tarbert, Cook and Statfjord reservoirs. Repeatability analysis has shown that the earlier seismic vintages are the most unreliable for amplitude anomaly analysis as normalised root-mean square (NRMS) values are greater than 50%. This is above the threshold of good and medium repeatability. Fluid substitution models show increases in both P-wave velocity and density for increasing water saturations with a maximum change of 7.33% in the P-wave velocity, and this is in line with predictions from previous work using the Biot - Gassman equations. AVO modelling for the top Tarbert Formation interface produced scenarios of increasing amplitudes with offset for the presence of hydrocarbons, which dim out with 100% brine saturation. This correlates to class III gas sands for different situations of varying Poisson's ratio across an interface, which has been previously modelled. Two anomalies were identified with one being related to increasing pressure due to water injection correlating to poor permeability around injector well 34/10-B-33. The second anomaly is a case of potential unswept hydrocarbons that displayed a consistent bright spot throughout all of the seismic vintages (in-inlines and crosslines). AVO attribute analysis of this event produced a class II anomaly. However, when comparing near and far offset seismic data, dimming effect was observed producing contrasting evidence. The dimming offset is viewed to have been as a result of poor repeatability values at far offsets. The modelling of the fluid contents in the studied formations to conform to existing literatures justifies the efficacy of the method.

Temperature offset control system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fried, M.

1987-07-28

This patent describes a temperature offset control system for controlling the operation of both heating and air conditioning systems simultaneously contained within the same premises each of which is set by local thermostats to operate at an appropriate temperature, the offset control system comprising: a central control station having means for presetting an offset temperature range, means for sensing the temperature at a central location, means for comparing the sensed temperature with the offset temperature range, means responsive to the comparison for producing a control signal indicative of whether the sensed temperature is within the offset temperature range or beyondmore » the offset temperature range, and means for transmitting the control signal onto the standard energy lines servicing the premises; and a receiving station respectively associated with each heating and air conditioning system, the receiving stations each comprising means for receiving the same transmitted control signal from the energy lines, and switch means for controlling the energization of the respective system in response to the received control signal. The heating systems and associated local thermostat are disabled by the control signal when the control signal originates from a sensed temperature above the lower end of the offset temperature range. The air conditioning systems and associated thermostats are disabled by the same control signal when the control signal originates from a sensed temperature below the upper end of the offset temperature range.« less

The auditory P50 component to onset and offset of sound

PubMed Central

Pratt, Hillel; Starr, Arnold; Michalewski, Henry J.; Bleich, Naomi; Mittelman, Nomi

2008-01-01

Objective: The auditory Event-Related Potentials (ERP) component P50 to sound onset and offset have been reported to be similar, but their magnetic homologue has been reported absent to sound offset. We compared the spatio-temporal distribution of cortical activity during P50 to sound onset and offset, without confounds of spectral change. Methods: ERPs were recorded in response to onsets and offsets of silent intervals of 0.5 s (gaps) appearing randomly in otherwise continuous white noise and compared to ERPs to randomly distributed click pairs with half second separation presented in silence. Subjects were awake and distracted from the stimuli by reading a complicated text. Measures of P50 included peak latency and amplitude, as well as source current density estimates to the clicks and sound onsets and offsets. Results P50 occurred in response to noise onsets and to clicks, while to noise offset it was absent. Latency of P50 was similar to noise onset (56 msec) and to clicks (53 msec). Sources of P50 to noise onsets and clicks included bilateral superior parietal areas. In contrast, noise offsets activated left inferior temporal and occipital areas at the time of P50. Source current density was significantly higher to noise onset than offset in the vicinity of the temporo-parietal junction. Conclusions: P50 to sound offset is absent compared to the distinct P50 to sound onset and to clicks, at different intracranial sources. P50 to stimulus onset and to clicks appears to reflect preattentive arousal by a new sound in the scene. Sound offset does not involve a new sound and hence the absent P50. Significance: Stimulus onset activates distinct early cortical processes that are absent to offset. PMID:18055255

Seismic amplitude anomalies at Mestena Grande field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burnett, R.

1989-09-01

Mestena Grande field is located in northeast Jim Hogg County, Texas. Gas and condensate are produced from the middle lobe of the middle Eocene Queen City Formation. The Queen City is approximately 100 ft thick and the middle lobe, the main reservoir, is only 30 ft thick, which is well below tuning thickness. Porosities in the producing sands are generally 15-25% and permeabilities are usually 15-25 md, the maximum being about 80 md. The most recent seismic data exhibit amplitude anomalies that have some correspondence with the production. The strongest amplitudes are from the vicinity of the better wells andmore » increase with offset. Most of the dry holes are on weak amplitudes that decrease with offset. Modeling the AVO response of a productive well, however, has predicted an amplitude decrease with offset. This disagreement is attributed to the lack of accurate shear wave velocities and the very thinly laminated sands.« less

On determining fluxgate magnetometer spin axis offsets from mirror mode observations

NASA Astrophysics Data System (ADS)

Plaschke, Ferdinand; Narita, Yasuhito

2016-09-01

In-flight calibration of fluxgate magnetometers that are mounted on spacecraft involves finding their outputs in vanishing ambient fields, the so-called magnetometer offsets. If the spacecraft is spin-stabilized, then the spin plane components of these offsets can be relatively easily determined, as they modify the spin tone content in the de-spun magnetic field data. The spin axis offset, however, is more difficult to determine. Therefore, usually Alfvénic fluctuations in the solar wind are used. We propose a novel method to determine the spin axis offset: the mirror mode method. The method is based on the assumption that mirror mode fluctuations are nearly compressible such that the maximum variance direction is aligned to the mean magnetic field. Mirror mode fluctuations are typically found in the Earth's magnetosheath region. We introduce the method and provide a first estimate of its accuracy based on magnetosheath observations by the THEMIS-C spacecraft. We find that 20 h of magnetosheath measurements may already be sufficient to obtain high-accuracy spin axis offsets with uncertainties on the order of a few tenths of a nanotesla, if offset stability can be assumed.

Broach Handle Design Changes Force Distribution in the Femur During Total Hip Arthroplasty.

PubMed

Greenhill, Dustin A; Abbasi, Pooyan; Darvish, Kurosh; Star, Andrew M

2017-06-01

Curved broach handles were developed to overcome limited surgical exposures during total hip arthroplasty. Some authors report increased intraoperative fracture rates during limited exposures. This study evaluates mechanical force ratios transmitted to the bone while broaching with curved vs straight handles. An experimental model utilized a 6-axis load cell to measure force distributions produced by 4 different broach handles, each with increasing offset and curvature. Handles were separately impacted and dynamic variables assessed. Handles were then digitized using a high-resolution optical system and a finite element analysis (FEA) was performed to account for trabecular bone and vary the location of mallet impact. Off-axis forces, broaching construct moments, and stress within surrounding bone were computed. Using the experimental model, high-offset handles lost on average 4% more hammering force to the horizontal axis. When the FEA utilized moduli of elasticity to estimate broaching through osteoporotic trabecular bone, horizontally displaced forces (toward cortical bone) were magnified from 4% to a maximum value of 52%. Both the experimental construct and FEA confirmed that larger offset handles increase moment-to-force ratios up to 163%-235%, thus rotating the proximal and distal ends of the broach toward cortical bone. Broach handle design is an important determinant of resultant forces transmitted to the broach (and ultimately the bone) during total hip arthroplasty. Unwanted off-axis forces and enhanced rotational dynamics may play a role in intraoperative fractures during femoral canal preparation. Copyright © 2016 Elsevier Inc. All rights reserved.

Forest biomass and tree planting for fossil fuel offsets in the Colorado Front Range

Treesearch

Mike A. Battaglia; Kellen Nelson; Dan Kashian; Michael G. Ryan

2010-01-01

This study estimates the amount of carbon available for removal in fuel reduction and reforestation treatments in montane forests of the Colorado Front Range based on site productivity, pre-treatment basal area, and planting density. Thinning dense stands will yield the greatest offsets for biomass fuel. However, this will also yield the greatest carbon losses, if the...

Performance Analysis for Channel Estimation With 1-Bit ADC and Unknown Quantization Threshold

NASA Astrophysics Data System (ADS)

Stein, Manuel S.; Bar, Shahar; Nossek, Josef A.; Tabrikian, Joseph

2018-05-01

In this work, the problem of signal parameter estimation from measurements acquired by a low-complexity analog-to-digital converter (ADC) with $1$-bit output resolution and an unknown quantization threshold is considered. Single-comparator ADCs are energy-efficient and can be operated at ultra-high sampling rates. For analysis of such systems, a fixed and known quantization threshold is usually assumed. In the symmetric case, i.e., zero hard-limiting offset, it is known that in the low signal-to-noise ratio (SNR) regime the signal processing performance degrades moderately by ${2}/{\\pi}$ ($-1.96$ dB) when comparing to an ideal $\\infty$-bit converter. Due to hardware imperfections, low-complexity $1$-bit ADCs will in practice exhibit an unknown threshold different from zero. Therefore, we study the accuracy which can be obtained with receive data processed by a hard-limiter with unknown quantization level by using asymptotically optimal channel estimation algorithms. To characterize the estimation performance of these nonlinear algorithms, we employ analytic error expressions for different setups while modeling the offset as a nuisance parameter. In the low SNR regime, we establish the necessary condition for a vanishing loss due to missing offset knowledge at the receiver. As an application, we consider the estimation of single-input single-output wireless channels with inter-symbol interference and validate our analysis by comparing the analytic and experimental performance of the studied estimation algorithms. Finally, we comment on the extension to multiple-input multiple-output channel models.

Right-lateral shear across Iran and kinematic change in the Arabia-Eurasia collision zone

NASA Astrophysics Data System (ADS)

Allen, M. B.; Kheirkhah, M.; Emami, M.

2009-04-01

New offset determinations for right-lateral strike-slip faults in Iran redefine the kinematics of the Arabia-Eurasia collision. A series of right-lateral strike-slip faults is present across Iran between 48° and 57° E. Fault strikes vary between NW-SE and NNW-SSE. Individual faults west of ~53° E were active in the late Tertiary, but have limited evidence of activity. Faults east of ~53° E are seismically active and/or have geomorphic evidence for Holocene slip. None of the faults affects the GPS-derived regional velocity field, indicating active slip rates are ≤2 mm/yr. We estimate overall slip on these faults from offset geological and geomorphic markers, based on observations from satellite imagery, digital topography, geology maps and our own fieldwork observations, and combine these results with published estimates for fault slip in the east of the study area. Total offset of the Takab, Soltanieh, Indes, Bid Hand, Qom, Kashan, Deh Shir, Anar, Daviran, Kuh Banan and Dehu faults is at least 270 km and possibly higher. Other faults (e.g. Rafsanjan) have unknown amounts of right-lateral slip. Collectively, these faults are inferred to have accommodated part of the Arabia-Eurasia convergence by two mechanisms: (1) anti-clockwise, vertical axis rotations; (2) strain partitioning with coeval NE-SW crustal thickening in the Turkish-Iranian plateau to produce ~350 km of north-south plate convergence. The strike-slip faulting across Iran requires along-strike lengthening of the deformation zone. This was possible until the Pliocene, when the Afghan crust collided with the western margin of the Indian plate, thereby sealing off a free face at the eastern side of the Arabia-Eurasia collision zone. Continuing Arabia-Eurasia plate convergence had to be accommodated in new ways and new areas, leading to the present pattern of faulting from eastern Iran to western Turkey.

Error analysis in inverse scatterometry. I. Modeling.

PubMed

Al-Assaad, Rayan M; Byrne, Dale M

2007-02-01

Scatterometry is an optical technique that has been studied and tested in recent years in semiconductor fabrication metrology for critical dimensions. Previous work presented an iterative linearized method to retrieve surface-relief profile parameters from reflectance measurements upon diffraction. With the iterative linear solution model in this work, rigorous models are developed to represent the random and deterministic or offset errors in scatterometric measurements. The propagation of different types of error from the measurement data to the profile parameter estimates is then presented. The improvement in solution accuracies is then demonstrated with theoretical and experimental data by adjusting for the offset errors. In a companion paper (in process) an improved optimization method is presented to account for unknown offset errors in the measurements based on the offset error model.

Sensitivity analysis of the GNSS derived Victoria plate motion

NASA Astrophysics Data System (ADS)

Apolinário, João; Fernandes, Rui; Bos, Machiel

2014-05-01

Fernandes et al. (2013) estimated the angular velocity of the Victoria tectonic block from geodetic data (GNSS derived velocities) only.. GNSS observations are sparse in this region and it is therefore of the utmost importance to use the available data (5 sites) in the most optimal way. Unfortunately, the existing time-series were/are affected by missing data and offsets. In addition, some time-series were close to the considered minimal threshold value to compute one reliable velocity solution: 2.5-3.0 years. In this research, we focus on the sensitivity of the derived angular velocity to changes in the data (longer data-span for some stations) by extending the used data-span: Fernandes et al. (2013) used data until September 2011. We also investigate the effect of adding other stations to the solution, which is now possible since more stations became available in the region. In addition, we study if the conventional power-law plus white noise model is indeed the best stochastic model. In this respect, we apply different noise models using HECTOR (Bos et al. (2013), which can use different noise models and estimate offsets and seasonal signals simultaneously. The seasonal signal estimation is also other important parameter, since the time-series are rather short or have large data spans at some stations, which implies that the seasonal signals still can have some effect on the estimated trends as shown by Blewitt and Lavellee (2002) and Bos et al. (2010). We also quantify the magnitude of such differences in the estimation of the secular velocity and their effect in the derived angular velocity. Concerning the offsets, we investigate how they can, detected and undetected, influence the estimated plate motion. The time of offsets has been determined by visual inspection of the time-series. The influence of undetected offsets has been done by adding small synthetic random walk signals that are too small to be detected visually but might have an effect on the estimated trend (Williams 2003, Langbein 2012). Finally, our preferable angular velocity estimation is used to evaluate the consequences on the kinematics of the Victoria block, namely the magnitude and azimuth of the relative motions with respect to the Nubia and Somalia plates and their tectonic implications. References Agnew, D. C. (2013). Realistic simulations of geodetic network data: The Fakenet package, Seismol. Res. Lett., 84 , 426-432, doi:10.1785/0220120185. Blewitt, G. & Lavallee, D., (2002). Effect of annual signals on geodetic velocity, J. geophys. Res., 107(B7), doi:10.1029/2001JB000570. Bos, M.S., R.M.S. Fernandes, S. Williams, L. Bastos (2012) Fast Error Analysis of Continuous GNSS Observations with Missing Data, Journal of Geodesy, doi: 10.1007/s00190-012-0605-0. Bos, M.S., L. Bastos, R.M.S. Fernandes, (2009). The influence of seasonal signals on the estimation of the tectonic motion in short continuous GPS time-series, J. of Geodynamics, j.jog.2009.10.005. Fernandes, R.M.S., J. M. Miranda, D. Delvaux, D. S. Stamps and E. Saria (2013). Re-evaluation of the kinematics of Victoria Block using continuous GNSS data, Geophysical Journal International, doi:10.1093/gji/ggs071. Langbein, J. (2012). Estimating rate uncertainty with maximum likelihood: differences between power-law and flicker-random-walk models, Journal of Geodesy, Volume 86, Issue 9, pp 775-783, Williams, S. D. P. (2003). Offsets in Global Positioning System time series, J. Geophys. Res., 108, 2310, doi:10.1029/2002JB002156, B6.

Apparatus and method for producing an artificial gravitational field

NASA Technical Reports Server (NTRS)

Mccanna, Jason (Inventor)

1993-01-01

An apparatus and method is disclosed for producing an artificial gravitational field in a spacecraft by rotating the same around a spin axis. The centrifugal force thereby created acts as an artificial gravitational force. The apparatus includes an engine which produces a drive force offset from the spin axis to drive the spacecraft towards a destination. The engine is also used as a counterbalance for a crew cabin for rotation of the spacecraft. Mass of the spacecraft, which may include either the engine or crew cabin, is shifted such that the centrifugal force acting on that mass is no longer directed through the center of mass of the craft. This off-center centrifugal force creates a moment that counterbalances the moment produced by the off-center drive force to eliminate unwanted rotation which would otherwise be precipitated by the offset drive force.

Characterization of the porosity distribution in the upper part of the karst Biscayne aquifer using common offset ground penetrating radar, Everglades National Park, Florida

NASA Astrophysics Data System (ADS)

Mount, Gregory J.; Comas, Xavier; Cunningham, Kevin J.

2014-07-01

The karst Biscayne aquifer is characterized by a heterogeneous spatial arrangement of porosity and hydraulic conductivity, making conceptualization difficult. The Biscayne aquifer is the primary source of drinking water for millions of people in south Florida; thus, information concerning the distribution of karst features that concentrate the groundwater flow and affect contaminant transport is critical. The principal purpose of the study was to investigate the ability of two-dimensional ground penetrating radar (GPR) to rapidly characterize porosity variability in the karst Biscayne aquifer in south Florida. An 800-m-long GPR transect of a previously investigated area at the Long Pine Key Nature Trail in Everglades National Park, collected in fast acquisition common offset mode, shows hundreds of diffraction hyperbolae. The distribution of diffraction hyperbolae was used to estimate electromagnetic (EM) wave velocity at each diffraction location and to assess both horizontal and vertical changes in velocity within the transect. A petrophysical model (complex refractive index model or CRIM) was used to estimate total bulk porosity. A set of common midpoint surveys at selected locations distributed along the common-offset transect also were collected for comparison with the common offsets and were used to constrain one-dimensional (1-D) distributions of porosity with depth. Porosity values for the saturated Miami Limestone ranged between 25% and 41% for common offset GPR surveys, and between 23% and 39% for common midpoint GPR surveys. Laboratory measurements of porosity in five whole-core samples from the saturated part of the aquifer in the study area ranged between 7.1% and 41.8%. GPR estimates of porosity were found to be valid only under saturated conditions; other limitations are related to the vertical resolution of the GPR signal and the volume of the material considered by the measurement methodology. Overall, good correspondence between GPR estimates and the direct porosity values from the whole-core samples confirms the ability of GPR common offset surveys to provide rapid characterization of porosity variability in the Biscayne aquifer. The common offset survey method has several advantages: (1) improved time efficiency in comparison to other GPR acquisition modes such as common midpoints; and (2) enhanced lateral continuity of porosity estimates, particularly when compared to porosity measurements on 1-D samples such as rock cores. The results also support the presence of areas of low EM wave velocity or high porosity under saturated conditions, causing velocity pull-down areas and apparent sag features in the reflection record. This study shows that GPR can be a useful tool for improving understanding of the petrophysical properties of highly heterogeneous systems such as karst aquifers, and thus may assist with the development of more accurate groundwater flow models, such as those used for restoration efforts in the Everglades.

Characterization of the porosity distribution in the upper part of the karst Biscayne aquifer using common offset ground penetrating radar, Everglades National Park, Florida

USGS Publications Warehouse

Mountain, Gregory S.; Cunningham, Kevin J.; Comas, Xavier

2014-01-01

The karst Biscayne aquifer is characterized by a heterogeneous spatial arrangement of porosity and hydraulic conductivity, making conceptualization difficult. The Biscayne aquifer is the primary source of drinking water for millions of people in south Florida; thus, information concerning the distribution of karst features that concentrate the groundwater flow and affect contaminant transport is critical. The principal purpose of the study was to investigate the ability of two-dimensional ground penetrating radar (GPR) to rapidly characterize porosity variability in the karst Biscayne aquifer in south Florida. An 800-m-long GPR transect of a previously investigated area at the Long Pine Key Nature Trail in Everglades National Park, collected in fast acquisition common offset mode, shows hundreds of diffraction hyperbolae. The distribution of diffraction hyperbolae was used to estimate electromagnetic (EM) wave velocity at each diffraction location and to assess both horizontal and vertical changes in velocity within the transect. A petrophysical model (complex refractive index model or CRIM) was used to estimate total bulk porosity. A set of common midpoint surveys at selected locations distributed along the common-offset transect also were collected for comparison with the common offsets and were used to constrain one-dimensional (1-D) distributions of porosity with depth. Porosity values for the saturated Miami Limestone ranged between 25% and 41% for common offset GPR surveys, and between 23% and 39% for common midpoint GPR surveys. Laboratory measurements of porosity in five whole-core samples from the saturated part of the aquifer in the study area ranged between 7.1% and 41.8%. GPR estimates of porosity were found to be valid only under saturated conditions; other limitations are related to the vertical resolution of the GPR signal and the volume of the material considered by the measurement methodology. Overall, good correspondence between GPR estimates and the direct porosity values from the whole-core samples confirms the ability of GPR common offset surveys to provide rapid characterization of porosity variability in the Biscayne aquifer.The common offset survey method has several advantages: (1) improved time efficiency in comparison to other GPR acquisition modes such as common midpoints; and (2) enhanced lateral continuity of porosity estimates, particularly when compared to porosity measurements on 1-D samples such as rock cores. The results also support the presence of areas of low EM wave velocity or high porosity under saturated conditions, causing velocity pull-down areas and apparent sag features in the reflection record. This study shows that GPR can be a useful tool for improving understanding of the petrophysical properties of highly heterogeneous systems such as karst aquifers, and thus may assist with the development of more accurate groundwater flow models, such as those used for restoration efforts in the Everglades.

A novel joint timing/frequency synchronization scheme based on Radon-Wigner transform of LFM signals in CO-OFDM systems

NASA Astrophysics Data System (ADS)

Liu, Jianfei; Wei, Ying; Zeng, Xiangye; Lu, Jia; Zhang, Shuangxi; Wang, Mengjun

2018-03-01

A joint timing and frequency synchronization method has been proposed for coherent optical orthogonal frequency-division multiplexing (CO-OFDM) system in this paper. The timing offset (TO), integer frequency offset (FO) and the fractional FO can be realized by only one training symbol, which consists of two linear frequency modulation (LFM) signals with opposite chirp rates. By detecting the peak of LFM signals after Radon-Wigner transform (RWT), the TO and the integer FO can be estimated at the same time, moreover, the fractional FO can be acquired correspondingly through the self-correlation characteristic of the same training symbol. Simulation results show that the proposed method can give a more accurate TO estimation than the existing methods, especially at poor OSNR conditions; for the FO estimation, both the fractional and the integer FO can be estimated through the proposed training symbol with no extra overhead, a more accurate estimation and a large FO estimation range of [ - 5 GHz, 5GHz] can be acquired.

Financial Impact of Direct-Acting Oral Anticoagulants in Medicaid: Budgetary Assessment Based on Number Needed to Treat.

PubMed

Fairman, Kathleen A; Davis, Lindsay E; Kruse, Courtney R; Sclar, David A

2017-04-01

Faced with rising healthcare costs, state Medicaid programs need short-term, easily calculated budgetary estimates for new drugs, accounting for medical cost offsets due to clinical advantages. To estimate the budgetary impact of direct-acting oral anticoagulants (DOACs) compared with warfarin, an older, lower-cost vitamin K antagonist, on 12-month Medicaid expenditures for nonvalvular atrial fibrillation (NVAF) using number needed to treat (NNT). Medicaid utilization files, 2009 through second quarter 2015, were used to estimate OAC cost accounting for generic/brand statutory minimum (13/23%) and assumed maximum (13/50%) manufacturer rebates. NNTs were calculated from clinical trial reports to estimate avoided medical events for a hypothetical population of 500,000 enrollees (approximate NVAF prevalence × Medicaid enrollment) under two DOAC market share scenarios: 2015 actual and 50% increase. Medical service costs were based on published sources. Costs were inflation-adjusted (2015 US$). From 2009-2015, OAC reimbursement per claim increased by 173 and 279% under maximum and minimum rebate scenarios, respectively, while DOAC market share increased from 0 to 21%. Compared with a warfarin-only counterfactual, counts of ischemic strokes, intracranial hemorrhages, and systemic embolisms declined by 36, 280, and 111, respectively; counts of gastrointestinal hemorrhages increased by 794. Avoided events and reduced monitoring, respectively, offset 3-5% and 15-24% of increased drug cost. Net of offsets, DOAC-related cost increases were US$258-US$464 per patient per year (PPPY) in 2015 and US$309-US$579 PPPY after market share increase. Avoided medical events offset a small portion of DOAC-related drug cost increase. NNT-based calculations provide a transparent source of budgetary-impact information for new medications.

Scene-based nonuniformity correction algorithm based on interframe registration.

PubMed

Zuo, Chao; Chen, Qian; Gu, Guohua; Sui, Xiubao

2011-06-01

In this paper, we present a simple and effective scene-based nonuniformity correction (NUC) method for infrared focal plane arrays based on interframe registration. This method estimates the global translation between two adjacent frames and minimizes the mean square error between the two properly registered images to make any two detectors with the same scene produce the same output value. In this way, the accumulation of the registration error can be avoided and the NUC can be achieved. The advantages of the proposed algorithm lie in its low computational complexity and storage requirements and ability to capture temporal drifts in the nonuniformity parameters. The performance of the proposed technique is thoroughly studied with infrared image sequences with simulated nonuniformity and infrared imagery with real nonuniformity. It shows a significantly fast and reliable fixed-pattern noise reduction and obtains an effective frame-by-frame adaptive estimation of each detector's gain and offset.

Guiding optimal biofuels :

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paap, Scott M.; West, Todd H.; Manley, Dawn Kataoka

2013-01-01

In the current study, processes to produce either ethanol or a representative fatty acid ethyl ester (FAEE) via the fermentation of sugars liberated from lignocellulosic materials pretreated in acid or alkaline environments are analyzed in terms of economic and environmental metrics. Simplified process models are introduced and employed to estimate process performance, and Monte Carlo analyses were carried out to identify key sources of uncertainty and variability. We find that the near-term performance of processes to produce FAEE is significantly worse than that of ethanol production processes for all metrics considered, primarily due to poor fermentation yields and higher electricitymore » demands for aerobic fermentation. In the longer term, the reduced cost and energy requirements of FAEE separation processes will be at least partially offset by inherent limitations in the relevant metabolic pathways that constrain the maximum yield potential of FAEE from biomass-derived sugars.« less

Offset of pharmacodynamic effects and safety of remifentanil in intensive care unit patients with various degrees of renal impairment

PubMed Central

Breen, Des; Wilmer, Alexander; Bodenham, Andrew; Bach, Vagn; Bonde, Jan; Kessler, Paul; Albrecht, Sven; Shaikh, Soraya

2004-01-01

Introduction This open label, multicentre study was conducted to assess the times to offset of the pharmacodynamic effects and the safety of remifentanil in patients with varying degrees of renal impairment requiring intensive care. Methods A total of 40 patients, who were aged 18 years or older and had normal/mildly impaired renal function (estimated creatinine clearance ≥ 50 ml/min; n = 10) or moderate/severe renal impairment (estimated creatinine clearance <50 ml/min; n = 30), were entered into the study. Remifentanil was infused for up to 72 hours (initial rate 6–9 μg/kg per hour), with propofol administered if required, to achieve a target Sedation–Agitation Scale score of 2–4, with no or mild pain. Results There was no evidence of increased offset time with increased duration of exposure to remifentanil in either group. The time to offset of the effects of remifentanil (at 8, 24, 48 and 72 hours during scheduled down-titrations of the infusion) were more variable and were statistically significantly longer in the moderate/severe group than in the normal/mild group at 24 hours and 72 hours. These observed differences were not clinically significant (the difference in mean offset at 72 hours was only 16.5 min). Propofol consumption was lower with the remifentanil based technique than with hypnotic based sedative techniques. There were no statistically significant differences between the renal function groups in the incidence of adverse events, and no deaths were attributable to remifentanil use. Conclusion Remifentanil was well tolerated, and the offset of pharmacodynamic effects was not prolonged either as a result of renal dysfunction or prolonged infusion up to 72 hours. PMID:14975051

Ground deformation associated with the 2008 Sichuan Earthquake in China, estimated using a SAR offset-tracking method

NASA Astrophysics Data System (ADS)

Kobayashi, T.; Takada, Y.; Furuya, M.; Murakami, M.

2008-12-01

Introduction: A catastrophic earthquake struck China"fs Sichuan area on May 12, 2008, with the moment magnitude of 7.9 (USGS). The hypocenter and their aftershocks are distributed along the western edge of the Sichuan Basin, suggesting that this seismic event occurred at the Longmeng Shan fault zone which is constituted of major three active faults (Wenchuan-Maowen, Beichuan, and Pengguan faults). However, it is unclear whether these faults were directly involved in the mainshock rupture. An interferometry SAR (InSAR) analysis generally has a merit that we can detect ground deformation in a vast region with high precision, however, for the Sichuan event, the surface deformation near the fault zone has not been satisfactorily detected from the InSAR analyses due to a low coherency. An offset-tracking method is less precise but more robust for detecting large ground deformation than the interferometric approach. Our purpose is to detect the detail ground deformation immediately near the faults involved in the Sichuan event with applying the offset-tracking method. Analysis Method: We analyzed ALOS/PALSAR images, which have been taken from Path 471 to 476 of ascending track, acquired before and after the mainshock. We processed SAR data from the level-1.0 product, using a software package from Gamma Remote Sensing. For offset-tracking analysis we adopt intensity tracking method which is performed by cross-correlating samples of backscatter intensity of a master SAR image with samples from the corresponding search area of a slave image in order to estimate range and azimuth offset fields. We reduce stereoscopic effects that produce apparent offsets, using SRTM3 DEM data. Results: We have successfully obtained the surface deformation in range (radar look direction) component, while in azimuth (flight direction) no significant deformation can be detected in some orbits due to "gazimuth streaks"h that are errors caused by ionospheric effects. Some concluding remarks are as follows: On the Beichuan F. and its northeastward extension, a clear boundary of a motion toward and away from the satellite can be recognized just along the fault, which is almost consistent with a right-lateral fault motion. On the other hand, in the southwestern region from the Beichuan city where the three major faults are running almost parallel, two boundaries of motions can be recognized; On the Beichuan F. there are a clear displacement boundary in range component, while on the Pengguan F. a boundary can be identified in azimuth component rather than in range, suggesting that the seismic ruptures proceeded with different fault motions at each fault. For the Wenchuan-Maowen F., no significant displacement boundary can be recognized. Acknowledgments: PALSAR data are provided from Earthquake Working Group and PIXEL (PALSAR Interferometry Consortium to Study our Evolving Land surface) under a cooperative research contract with JAXA. The ownership of PALSAR data belongs to METI (Ministry of Economy, Trade and Industry) and JAXA.

Investigation on synchronization of the offset printing process for fine patterning and precision overlay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kang, Dongwoo; Lee, Eonseok; Kim, Hyunchang

2014-06-21

Offset printing processes are promising candidates for producing printed electronics due to their capacity for fine patterning and suitability for mass production. To print high-resolution patterns with good overlay using offset printing, the velocities of two contact surfaces, which ink is transferred between, should be synchronized perfectly. However, an exact velocity of the contact surfaces is unknown due to several imperfections, including tolerances, blanket swelling, and velocity ripple, which prevents the system from being operated in the synchronized condition. In this paper, a novel method of measurement based on the sticking model of friction force was proposed to determine themore » best synchronized condition, i.e., the condition in which the rate of synchronization error is minimized. It was verified by experiment that the friction force can accurately represent the rate of synchronization error. Based on the measurement results of the synchronization error, the allowable margin of synchronization error when printing high-resolution patterns was investigated experimentally using reverse offset printing. There is a region where the patterning performance is unchanged even though the synchronization error is varied, and this may be viewed as indirect evidence that printability performance is secured when there is no slip at the contact interface. To understand what happens at the contact surfaces during ink transfer, the deformation model of the blanket's surface was developed. The model estimates how much deformation on the blanket's surface can be borne by the synchronization error when there is no slip at the contact interface. In addition, the model shows that the synchronization error results in scale variation in the machine direction (MD), which means that the printing registration in the MD can be adjusted actively by controlling the synchronization if there is a sufficient margin of synchronization error to guarantee printability. The effect of synchronization on the printing registration was verified experimentally using gravure offset printing. The variations in synchronization result in the differences in the MD scale, and the measured MD scale matches exactly with the modeled MD scale.« less

Biomass offsets little or none of permafrost carbon release from soils, streams, and wildfire: an expert assessment

Treesearch

Benjamin W Abbott; Jeremy B Jones; Edward A G Schuur; F Stuart Chapin III; William B Bowden; M Syndonia Bret-Harte; Howard E Epstein; Michael D Flannigan; Tamara K Harms; Teresa N Hollingsworth; Michelle C Mack; A David McGuire; Susan M Natali; Adrian V Rocha; Suzanne E Tank; Merritt R Turetsky; Jorien E Vonk; Kimberly P Wickland; George R Aiken; Heather D Alexander; Rainer M W Amon; Brian W Benscoter; Yves Bergeron; Kevin Bishop; Olivier Blarquez; Amy L Breen; Ishi Buffam; Yihua Cai; Christopher Carcaillet; Sean K Carey; Jing M Chen; Han Y H Chen; Torben R Christensen; Lee W Cooper; J Hans C Cornelissen; William J de Groot; Thomas H DeLuca; Ellen Dorrepaal; Ned Fetcher; Jacques C Finlay; Bruce C Forbes; Nancy H F French; Sylvie Gauthier; Martin P Girardin; Scott J Goetz; Johann G Goldammer; Laura Gough; Paul Grogan; Laodong Guo; Philip E Higuera; Larry Hinzman; Feng Sheng Hu; Gustaf Hugelius; Elchin E Jafarov; Randi Jandt; Jill F Johnstone; Eric S Kasischke; Gerhard Kattner; Ryan Kelly; Frida Keuper; George W Kling; Pirkko Kortelainen; Jari Kouki; Peter Kuhry; Hjalmar Laudon; Isabelle Laurion; Robie W Macdonald; Paul J Mann; Pertti J Martikainen; James W McClelland; Ulf Molau; Steven F Oberbauer; David Olefeldt; David Par??; Marc-Andr?? Parisien; Serge Payette; Changhui Peng; Oleg S Pokrovsky; Edward B Rastetter; Peter A Raymond; Martha K Raynolds; Guillermo Rein; James F Reynolds; Martin Robards; Brendan M Rogers; Christina Sch??del; Kevin Schaefer; Inger K Schmidt; Anatoly Shvidenko; Jasper Sky; Robert G M Spencer; Gregory Starr; Robert G Striegl; Roman Teisserenc; Lars J Tranvik; Tarmo Virtanen; Jeffrey M Welker; Sergei Zimov

2016-01-01

As the permafrost region warms, its large organic carbon pool will be increasingly vulnerable to decomposition, combustion, and hydrologic export. Models predict that some portion of this release will be offset by increased production of Arctic and boreal biomass; however, the lack of robust estimates of net carbon balance increases the risk of further overshooting...

Effect of DC Offset on the T-Wave Residuum Parameter

NASA Technical Reports Server (NTRS)

Scott, N.; Greco, E. C.; Schlegel, Todd T.

2006-01-01

The T-wave residuum (TWR) is a relatively new 12-lead ECG parameter that may reflect cardiac repolarization heterogeneity. TWR shows clinical promise and may become an important diagnostic tool if accurate, consistent, and convenient methods for its calculation can be developed. However, there are discrepancies between the methods that various investigators have used to calculate TWR, as well as some questions about basic methodology and assumptions that require resolution. The presence of a DC offset or very low frequency AC component to the ECG is often observed. Many researchers have attempted to compensate for these by high pass filters and by median beat techniques. These techniques may help minimize the contribution of a low frequency AC component to the TWR, but they will not eliminate a DC offset inherent within the instrumentation. The present study examined the presence of DC offsets in the ECG record, and their effect on TWR. Specifically, in healthy individuals, a DC offset was added to all 8 channels collectively or to each channel selectively. Even with offsets that were relatively small compared to T-wave amplitude, the addition of either collectively or individually applied offsets was observed to produce very significant changes in the TWR, affecting its value by as much as an order of magnitude. These DC offsets may arise from at least two possible sources: a transient artifact from EMG or electrode movement resulting in a transient baseline offset in one or more channels. Since highpass filters have a settling time of several seconds, these artifacts will contribute to a transitory baseline offset lasting 1020 cycles. The machine hardware may also introduce an offset. Regardless of the cause or source of a DC offset, this study demonstrates that offsets have a very significant impact on TWR, and that future studies must not ignore their presence, but rather more appropriately compensate for them.

LATERAL OFFSET OF THE CORONAL MASS EJECTIONS FROM THE X-FLARE OF 2006 DECEMBER 13 AND ITS TWO PRECURSOR ERUPTIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sterling, Alphonse C.; Moore, Ronald L.; Harra, Louise K., E-mail: alphonse.sterling@nasa.gov, E-mail: ron.moore@nasa.gov, E-mail: lkh@mssl.ucl.ac.uk

2011-12-10

Two GOES sub-C-class precursor eruptions occurred within {approx}10 hr prior to and from the same active region as the 2006 December 13 X4.3-class flare. Each eruption generated a coronal mass ejection (CME) with center laterally far offset ({approx}> 45 Degree-Sign ) from the co-produced bright flare. Explaining such CME-to-flare lateral offsets in terms of the standard model for solar eruptions has been controversial. Using Hinode/X-Ray Telescope (XRT) and EUV Imaging Spectrometer (EIS) data, and Solar and Heliospheric Observatory (SOHO)/Large Angle and Spectrometric Coronagraph (LASCO) and Michelson Doppler Imager (MDI) data, we find or infer the following. (1) The first precursormore » was a 'magnetic-arch-blowout' event, where an initial standard-model eruption of the active region's core field blew out a lobe on one side of the active region's field. (2) The second precursor began similarly, but the core-field eruption stalled in the side-lobe field, with the side-lobe field erupting {approx}1 hr later to make the CME either by finally being blown out or by destabilizing and undergoing a standard-model eruption. (3) The third eruption, the X-flare event, blew out side lobes on both sides of the active region and clearly displayed characteristics of the standard model. (4) The two precursors were offset due in part to the CME originating from a side-lobe coronal arcade that was offset from the active region's core. The main eruption (and to some extent probably the precursor eruptions) was offset primarily because it pushed against the field of the large sunspot as it escaped outward. (5) All three CMEs were plausibly produced by a suitable version of the standard model.« less

AN EXPERIMENTAL INVESTIGATION OF MICROPRINTING BY THE OFFSET METHOD.

DTIC Science & Technology

Continuous tone original art was photographed to produce a screened negative which was contact printed. The fullscale positive halftone was...photographically reduced 5.55 X to make a second negative which was contact printed on the offset plate. This reduction was equivalent to printing halftones ...reduced and printed. Macroscopic examination of printed materials mentioned above indicated that the halftones were good enough for identification in P

IMPROVING PROCEDURES FOR PRODUCING OVERHEAD TRANSPARENCIES WITH THE ULTIMATE AIM OF INCORPORATING THESE TECHNIQUES INTO THE DEVELOPMENT OF A REGIONAL CURRICULAR MATERIALS CENTER FOR VOCATIONAL EDUCATION. FINAL REPORT.

ERIC Educational Resources Information Center

JENSEN, ARTHUR K.

THE INVESTIGATION RESULTED IN THE PRODUCTION OF 88 LOW-COST OVERHEAD PROJECTION TRANSPARENCIES ON THE BASIC PRINCIPLES OF POWER TRANSMISSION IN AGRICULTURAL MACHINERY. DEVELOPING TECHNIQUES FOR OFFSET PRINTING ON PLASTIC REQUIRED OVERCOMING PROBLEMS OF STATIC ELECTRICITY, INK ADHESION, OFFSETTING, AND DRYING. MACHINERY, ENVIRONMENT, AND INK WERE…

77 FR 28570 - Pure Magnesium From the People's Republic of China: Notice of Court Decision Not in Harmony With...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-15

... Department granted TMI's request for two by-product offsets, and calculated a dumping margin for TMI of 0.63... review. At verification, TMI's producer revealed that there were no by-product sales prior to April 2007... instructed to: (1) Further explain the valuation of TMI's by-product offsets; and (2) further explain the...

Earthquake geology of the Bulnay Fault (Mongolia)

USGS Publications Warehouse

Rizza, Magali; Ritz, Jean-Franciois; Prentice, Carol S.; Vassallo, Ricardo; Braucher, Regis; Larroque, Christophe; Arzhannikova, A.; Arzhanikov, S.; Mahan, Shannon; Massault, M.; Michelot, J-L.; Todbileg, M.

2015-01-01

The Bulnay earthquake of July 23, 1905 (Mw 8.3-8.5), in north-central Mongolia, is one of the world's largest recorded intracontinental earthquakes and one of four great earthquakes that occurred in the region during the 20th century. The 375-km-long surface rupture of the left-lateral, strike-slip, N095°E trending Bulnay Fault associated with this earthquake is remarkable for its pronounced expression across the landscape and for the size of features produced by previous earthquakes. Our field observations suggest that in many areas the width and geometry of the rupture zone is the result of repeated earthquakes; however, in those areas where it is possible to determine that the geomorphic features are the result of the 1905 surface rupture alone, the size of the features produced by this single earthquake are singular in comparison to most other historical strike-slip surface ruptures worldwide. Along the 80 km stretch, between 97.18°E and 98.33°E, the fault zone is characterized by several meters width and the mean left-lateral 1905 offset is 8.9 ± 0.6 m with two measured cumulative offsets that are twice the 1905 slip. These observations suggest that the displacement produced during the penultimate event was similar to the 1905 slip. Morphotectonic analyses carried out at three sites along the eastern part of the Bulnay fault, allow us to estimate a mean horizontal slip rate of 3.1 ± 1.7 mm/yr over the Late Pleistocene-Holocene period. In parallel, paleoseismological investigations show evidence for two earthquakes prior to the 1905 event with recurrence intervals of ~2700-4000 years.

Offset frequency dynamics and phase noise properties of a self-referenced 10 GHz Ti:sapphire frequency comb.

PubMed

Heinecke, Dirk C; Bartels, Albrecht; Diddams, Scott A

2011-09-12

This paper shows the experimental details of the stabilization scheme that allows full control of the repetition rate and the carrier-envelope offset frequency of a 10 GHz frequency comb based on a femtosecond Ti:sapphire laser. Octave-spanning spectra are produced in nonlinear microstructured optical fiber, in spite of the reduced peak power associated with the 10 GHz repetition rate. Improved stability of the broadened spectrum is obtained by temperature-stabilization of the nonlinear optical fiber. The carrier-envelope offset frequency and the repetition rate are simultaneously frequency stabilized, and their short- and long-term stabilities are characterized. We also measure the transfer of amplitude noise of the pump source to phase noise on the offset frequency and verify an increased sensitivity of the offset frequency to pump power modulation compared to systems with lower repetition rate. Finally, we discuss merits of this 10 GHz system for the generation of low-phase-noise microwaves from the photodetected pulse train.

Software for Quantitative Estimation of Coefficients of Ink Transfer on the Printed Substrate in Offset Printing

NASA Astrophysics Data System (ADS)

Varepo, L. G.; Trapeznikova, O. V.; Panichkin, A. V.; Roev, B. A.; Kulikov, G. B.

2018-04-01

In the framework of standardizing the process of offset printing, one of the most important tasks is the correct selection of the printing system components, taking into account the features of their interaction and behavior in the printing process. The program allows to calculate the transfer of ink on the printed material between the contacting cylindrical surfaces of the sheet-fed offset printing apparatus with the boundaries deformation. A distinctive feature of this software product is the modeling of the liquid flow having free boundaries and causing deformation of solid boundaries when flowing between the walls of two cylinders.

Phonation offset in tracheoesophageal speech.

PubMed

Searl, Jeff; Ousley, Teri

2004-01-01

Tracheoesophageal (TE) speakers often have difficulty producing the voiced-voiceless distinction. Phonation offset (POff) as a TE speaker transitions from a vowel to a stop consonant may be altered, possibly contributing to listener misperceptions. The purposes of this study were to: (1) compare the duration of POff in TE versus laryngeal speakers, and (2) compare POff between TE productions that were accurately versus inaccurately perceived. Phonation offset and offset duration as a proportion of the stop gap (%POff) were greater for the TE versus the laryngeal samples. There was no difference in POff or %POff when comparing accurately to inaccurately perceived TE samples. Tracheoesophageal speakers may have less ability to halt neoglottal vibration compared to laryngeal speakers' ability to stop glottal vibration. Comparable POff for accurately and inaccurately perceived TE samples suggests that POff may not be a particularly salient acoustic feature to the voicing distinction, at least for stop consonants. (1) As a result of this activity, participants will be able to describe what phonation offset is relative to the voicing distinction. (2) As a result of this activity, participants will be able to describe phonation offset in tracheoesophageal speakers relative to laryngeal speakers. (3) As a result of this activity, participants will be able to describe whether phonation offset in tracheoesophageal speech has perceptual saliency for listeners.

Joint carrier phase and frequency-offset estimation with parallel implementation for dual-polarization coherent receiver.

PubMed

Lu, Jianing; Li, Xiang; Fu, Songnian; Luo, Ming; Xiang, Meng; Zhou, Huibin; Tang, Ming; Liu, Deming

2017-03-06

We present dual-polarization complex-weighted, decision-aided, maximum-likelihood algorithm with superscalar parallelization (SSP-DP-CW-DA-ML) for joint carrier phase and frequency-offset estimation (FOE) in coherent optical receivers. By pre-compensation of the phase offset between signals in dual polarizations, the performance can be substantially improved. Meanwhile, with the help of modified SSP-based parallel implementation, the acquisition time of FO and the required number of training symbols are reduced by transferring the complex weights of the filters between adjacent buffers, where differential coding/decoding is not required. Simulation results show that the laser linewidth tolerance of our proposed algorithm is comparable to traditional blind phase search (BPS), while a complete FOE range of ± symbol rate/2 can be achieved. Finally, performance of our proposed algorithm is experimentally verified under the scenario of back-to-back (B2B) transmission using 10 Gbaud DP-16/32-QAM formats.

A seismic refraction and reflection study across the central San Jacinto Basin, Southern California

USGS Publications Warehouse

Lee, T.-C.; Biehler, S.; Park, S.K.; Stephenson, W.J.

1996-01-01

The San Jacinto Basin is a northwest-trending, pullapart basin in the San Jacinto fault zone of the San Andreas fault system in southern California. About 24 km long and 2 to 4 km wide, the basin sits on a graben bounded by two strands of the San Jacinto fault zone: the Claremont Fault on the northeast and the Casa Loma Fault on the southwest. We present a case study of shallow structure (less than 1 km) in the central basin. A 2.75-km refraction line running from the northeast to southwest across the regional structural trend reveals a groundwater barrier (Offset I). Another line, bent southward and continued for 1.65-km, shows a crystalline basement offset (Offset III) near an inferred trace of the Casa Loma Fault. Although a basement refractor was not observed along the 2.75-km line, a mismatch between the estimate of its minimum depth and the basement depth determined for the 1.65-km line suggests that an offset in the basement (greater than 260 m) exists around the junction of the two refraction lines (Offset II). By revealing more faults and subtle sedimentary structures, the reflection stack sections confirm the two refraction offsets as faults. Offsets I and III each separate sediments of contrasting structures and, in addition. Offset III disrupts an unconformity. However, the sense and amount of the offset across Offset III contradict what may be expected across the Casa Loma Fault, which has its basinward basement down-thrown to about 2.5 km in the better defined southeastern part of the graben. The Casa Loma Fault trace has been mislinked in the existing geological maps and the trace should be remapped to Offset II where the reflector disruptions spread over a 400-m wide zone. Our Offset III is an unnamed, concealed fault.

Venus' center of figure-center of mass offset

NASA Technical Reports Server (NTRS)

Bindschadler, Duane L.; Schubert, Gerald; Ford, Peter G.

1994-01-01

Magellan altimetry data reveal that the center of figure (CF) of Venus is displaced approximately 280 m from its center of mass (CM) toward 4.4 deg S, 135.8 deg E, a location in Aphrodite Terra. This offset is smaller than those of other terrestrial planets but larger than the estimated error, which is no more than a few tens of meters. We examine the possibility that the CF-CM offset is related to specific geologic provinces on Venus by deriving three simple models for the offset: a thick-crust model, a hotspot model, and a thick-lithosphere model. The offset caused by a region of thick crust depends upon the region's extent, the crust-mantle density contrast, and the thickness of excess crust. A hotspot-related offset depends on the extent of the thermally anomalous region and the magnitude of the thermal anomaly. Offset due to a region of thick lithosphere depends upon the extent of the region, the average temperature contrast across the lithosphere, and the amount of excess lithosphere. We apply the three models to Venus plateau-shaped highlands, volcanic rises, and lowlands, respectively, in an attempt to match the observed CF-CM offset location and magnitude. The influence of most volcanic rises and of Ishtar Terra on the CF-CM offset must be quite small if we are to explain the direction of the observed offset. The lack of influence of volcanic rises can be explained if the related thermal anomalies are limited to a few hundred degrees or less and are plume-shaped (i.e., characterized by a flattened sublithospheric `head' with a narrow cylindrical feeder `tail'). The unimportance of Ishtar Terra is most easily explained if it lies atop a significant mantle downwelling.

Analog-to-digital conversion as a source of drifts in displacements derived from digital recordings of ground acceleration

USGS Publications Warehouse

Boore, D.M.

2003-01-01

Displacements obtained from double integration of digitally recorded ground accelerations often show drifts much larger than those expected for the true ground displacements. These drifts might be due to many things, including dynamic elastic ground tilt, inelastic ground deformation, hysteresis in the instruments, and cross feed due to misalignment of nominally orthogonal sensors. This article shows that even if those effects were not present, the analog-to-digital conversion (ADC) process can produce apparent "pulses" and offsets in the acceleration baseline if the ground motion is slowly varying compared with the quantization level of the digitization. Such slowly varying signals can be produced by constant offsets that do not coincide with a quantization level and by near- and intermediate-field terms in the wave field radiated from earthquakes. Double integration of these apparent pulses and offsets leads to drifts in the displacements similar to those found in processing real recordings. These effects decrease in importance as the resolution of the ADC process increases.

Could offset cluster reveal strong earthquake pattern?——case study from Haiyuan Fault

NASA Astrophysics Data System (ADS)

Ren, Z.; Zhang, Z.; Chen, T.; Yin, J.; Zhang, P. Z.; Zheng, W.; Zhang, H.; Li, C.

2016-12-01

Since 1990s, researchers tried to use offset clusters to study strong earthquake patterns. However, due to the limitation of quantity of offset data, it was not widely used until recent years with the rapid development of high-resolution topographic data, such as remote sensing images, LiDAR. In this study, we use airborne LiDAR data to re-evaluate the cumulative offsets and co-seismic offset of the 1920 Haiyuan Ms 8.5 earthquake along the western and middle segments of the co-seismic surface rupture zone. Our LiDAR data indicate the offset observations along both the western and middle segments fall into five groups. The group with minimum slip amount is associated with the 1920 Haiyuan Ms 8.5 earthquake, which ruptured both the western and middle segments. Our research highlights two new interpretations: firstly, the previously reported maximum displacement of the 1920 Earthquake is likely to be produced by at least two earthquakes; secondly, Our results reveal that the Cumulative Offset Probability Density (COPD) peaks of same offset amount on western segment and middles segment did not corresponding to each other one by one. The ages of the paleoearthquakes indicate the offsets are not accumulated during same period. We suggest that any discussion of the rupture pattern of a certain fault based on the offset data should also consider fault segmentation and paleoseismological data; Therefore, using the COPD peaks for studying the number of palaeo-events and their rupture patterns, the COPD peaks should be computed and analyzed on fault sub-sections and not entire fault zones. Our results reveal that the rupture pattern on the western and middle segment of the Haiyuan Fault is different from each other, which provide new data for the regional seismic potential analysis.

Coseismic slip distributions of the 26 December 2004 Sumatra-Andaman and 28 March 2005 Nias earthquakes from GPS static offsets

USGS Publications Warehouse

Banerjee, P.; Pollitz, F.; Nagarajan, B.; Burgmann, R.

2007-01-01

Static offsets produced by the 26 December 2004 M ???9 Sumatra-Andaman earthquake as measured by Global Positioning System (GPS) reveal a large amount of slip along the entire ???1300 km-long rupture. Most seismic slip inversions place little slip on the Andaman segment. whereas both near-field and far-field GPS offsets demand large slip on the Andaman segment. We compile available datasets of the static offset to render a more detailed picture of the static-slip distribution. We construct geodetic offsets such that postearthquake positions of continuous GPS sites are reckoned to a time 1 day after the earthquake and campaign GPS sites are similarly corrected for postseismic motions. The newly revised slip distribution (Mw 9.22) reveals substantial segmentation of slip along the Andaman Islands, with the southern quarter slipping ???15 m in unison with the adjacent Nicobar and northern Sumatran segments of length ???700 km. We infer a small excess of geodetic moment relative to the seismic moment. A similar compilation of GPS offsets from the 28 March 2005 Nias earthquake is well explained with dip slip averaging several meters (Mw = 8.66) distributed primarily at depths greater than 20 km.

Cancellation of birefringence in DBR laser through principal axis offset by a rotation of 90°

NASA Astrophysics Data System (ADS)

Zaini, M. K. A.; Lai, M. H.; Islam, M. R.; Lim, K. S.; Ahmad, H.

2018-04-01

The cancellation of birefringence in the distributed Bragg reflector based on 90° rotation offset method is demonstrated. It is found that the birefringence, which causes the peak bifurcation has been eliminated and a single peak is produced at each resonance in the output spectrum. This modification is an economic solution for eliminating the birefringence of the optical fibre devices.

A simulation model to estimate cost-offsets for a disease-management program for chronic kidney disease.

PubMed

Gandjour, Afschin; Tschulena, Ulrich; Steppan, Sonja; Gatti, Emanuele

2015-04-01

The aim of this paper is to develop a simulation model that analyzes cost-offsets of a hypothetical disease management program (DMP) for patients with chronic kidney disease (CKD) in Germany compared to no such program. A lifetime Markov model with simulated 65-year-old patients with CKD was developed using published data on costs and health status and simulating the progression to end-stage renal disease (ESRD), cardiovascular disease and death. A statutory health insurance perspective was adopted. This modeling study shows considerable potential for cost-offsets from a DMP for patients with CKD. The potential for cost-offsets increases with relative risk reduction by the DMP and baseline glomerular filtration rate. Results are most sensitive to the cost of dialysis treatment. This paper presents a general 'prototype' simulation model for the prevention of ESRD. The model allows for further modification and adaptation in future applications.

Measuring earthquakes from optical satellite images.

PubMed

Van Puymbroeck, N; Michel, R; Binet, R; Avouac, J P; Taboury, J

2000-07-10

Système pour l'Observation de la Terre images are used to map ground displacements induced by earthquakes. Deformations (offsets) induced by stereoscopic effect and roll, pitch, and yaw of satellite and detector artifacts are estimated and compensated. Images are then resampled in a cartographic projection with a low-bias interpolator. A subpixel correlator in the Fourier domain provides two-dimensional offset maps with independent measurements approximately every 160 m. Biases on offsets are compensated from calibration. High-frequency noise (0.125 m(-1)) is approximately 0.01 pixels. Low-frequency noise (lower than 0.001 m(-1)) exceeds 0.2 pixels and is partially compensated from modeling. Applied to the Landers earthquake, measurements show the fault with an accuracy of a few tens of meters and yields displacement on the fault with an accuracy of better than 20 cm. Comparison with a model derived from geodetic data shows that offsets bring new insights into the faulting process.

DC coupled Doppler radar physiological monitor.

PubMed

Zhao, Xi; Song, Chenyan; Lubecke, Victor; Boric-Lubecke, Olga

2011-01-01

One of the challenges in Doppler radar systems for physiological monitoring is a large DC offset in baseband outputs. Typically, AC coupling is used to eliminate this DC offset. Since the physiological signals of interest include frequency content near DC, it is not desirable to simply use AC coupling on the radar outputs. While AC coupling effectively removes DC offset, it also introduces a large time delay and distortion. This paper presents the first DC coupled IQ demodulator printed circuit board (PCB) design and measurements. The DC coupling is achieved by using a mixer with high LO to RF port isolation, resulting in a very low radar DC offset on the order of mV. The DC coupled signals from the PCB radar system were successfully detected with significant LNA gain without saturation. Compared to the AC coupled results, the DC coupled results show great advantages of less signal distortion and more accurate rate estimation.

A New Geological Slip Rate Estimate for the Calico Fault, Eastern California: Implications for Geodetic Versus Geologic Rate Estimates in the Eastern California Shear Zone

NASA Astrophysics Data System (ADS)

Wetmore, P. H.; Xie, S.; Gallant, E.; Owen, L. A.; Dixon, T. H.

2017-12-01

Fault slip rate is fundamental to accurate seismic hazard assessment. In the Mojave Desert section of the Eastern California Shear Zone previous studies have suggested a discrepancy between short-term geodetic and long-term geologic slip rate estimates. Understanding the origin of this discrepancy could lead to better understanding of stress evolution, and improve earthquake hazard estimates in general. We measured offsets in alluvial fans along the Calico fault near Newberry Springs, California, and used exposure age dating based on the cosmogenic nuclide 10Be to date the offset landforms. We derive a mean slip rate of 3.6 mm/yr, representing an average over the last few hundred thousand years, significantly faster than previous estimates. Considering numerous faults in the Mojave Desert and limited geologic slip rate estimates, it is premature to claim a geologic versus geodetic "discrepancy" for the ECSZ. More slip rate data, from all faults with the ECSZ, are needed to provide a statistically meaningful assessment of the geologic rates for each of the faults comprising the ECSZ.

Nonuniformity correction algorithm with efficient pixel offset estimation for infrared focal plane arrays.

PubMed

Orżanowski, Tomasz

2016-01-01

This paper presents an infrared focal plane array (IRFPA) response nonuniformity correction (NUC) algorithm which is easy to implement by hardware. The proposed NUC algorithm is based on the linear correction scheme with the useful method of pixel offset correction coefficients update. The new approach to IRFPA response nonuniformity correction consists in the use of pixel response change determined at the actual operating conditions in relation to the reference ones by means of shutter to compensate a pixel offset temporal drift. Moreover, it permits to remove any optics shading effect in the output image as well. To show efficiency of the proposed NUC algorithm some test results for microbolometer IRFPA are presented.

Surface rupture and slip variation induced by the 2010 El Mayor-Cucapah earthquake, Baja California, quantified using COSI-Corr analysis on pre- and post-earthquake LiDAR acquisitions

NASA Astrophysics Data System (ADS)

Leprince, S.; Hudnut, K. W.; Akciz, S. O.; Hinojosa-Corona, A.; Fletcher, J. M.

2011-12-01

One-hundred and three years after the publication of the Lawson report on the Great 1906 earthquake, accurate documentation of surface deformation along the entire length of an earthquake is still challenging. Analysis of pre- and post-earthquake topographic data provides an opportunity to deliver the full 3D displacement field of the ground's surface. However, direct differencing of a pre- and post-earthquake digital topography model (DEM) generally leads to biased estimation of the vertical component of the deformation. Indeed, if the earthquake also produced significant horizontal motion, or if the pre- and post-earthquake DEM acquisitions exhibit non-negligible horizontal mis-registration, then the vertical offset measured by direct differencing will be biased by the local topography gradient. To overcome this limitation, we use the COSI-Corr sub-pixel correlation algorithm to estimate the relative horizontal offset between the pre- and post- 2010 El Mayor - Cucapah earthquake high resolution LiDAR acquisitions. Compensating for the horizontal offset between the two LiDAR acquisitions allows us to estimate unbiased measurements of the vertical component of the surface fault rupture induced by the El Mayor-Cucapah earthquake. We will also show the limitations of the available data set, such as aircraft jitter artifacts, which impaired accurate measurements of the horizontal component of the surface deformation. This analysis shows an unprecedented view of the complete vertical slip component of the rupture induced by the Mw 7.2 2010 El Mayor-Cucapah earthquake, sampled at every 5 m, over a length of about 100 km, and with a vertical accuracy of a few centimeters. Using sampling bins as narrow as 150 m and 1.5 km long, variations in the vertical component of an oblique slip earthquake are presented, with breaks along multiple fault-strands showing opposite dip directions and diffuse boundaries. With the availability of high precision pre- and post-earthquake data, COSI-Corr has the ability to accurately document the variability of 3D surface slip along strike of an earthquake rupture. Such data can be used to investigate the causes of this variability, and improve our understanding of its influence on the pattern of ground shaking.

Parametric study in weld mismatch of longitudinally welded SSME HPFTP inlet

NASA Technical Reports Server (NTRS)

Min, J. B.; Spanyer, K. L.; Brunair, R. M.

1991-01-01

Welded joints are an essential part of pressure vessels such as the Space Shuttle Main Engine (SSME) Turbopumps. Defects produced in the welding process can be detrimental to weld performance. Recently, review of the SSME high pressure fuel turbopump (HPFTP) titanium inlet x rays revealed several weld discrepancies such as penetrameter density issues, film processing discrepancies, weld width discrepancies, porosity, lack of fusion, and weld offsets. Currently, the sensitivity of welded structures to defects is of concern. From a fatigue standpoint, weld offset may have a serious effect since local yielding, in general, aggravates cyclic stress effects. Therefore, the weld offset issue is considered. Using the finite element method and mathematical formulations, parametric studies were conducted to determine the influence of weld offsets and a variation of weld widths in longitudinally welded cylindrical structures with equal wall thickness on both sides of the joint. From the study, the finite element results and theoretical solutions are presented.

Software Modules for the Proximity-1 Space Link Interleaved Time Synchronization (PITS) Protocol

NASA Technical Reports Server (NTRS)

Woo, Simon S.; Veregge, John R.; Gao, Jay L.; Clare, Loren P.; Mills, David

2012-01-01

The Proximity-1 Space Link Interleaved Time Synchronization (PITS) protocol provides time distribution and synchronization services for space systems. A software prototype implementation of the PITS algorithm has been developed that also provides the test harness to evaluate the key functionalities of PITS with simulated data source and sink. PITS integrates time synchronization functionality into the link layer of the CCSDS Proximity-1 Space Link Protocol. The software prototype implements the network packet format, data structures, and transmit- and receive-timestamp function for a time server and a client. The software also simulates the transmit and receive-time stamp exchanges via UDP (User Datagram Protocol) socket between a time server and a time client, and produces relative time offsets and delay estimates.

Measurement of Separate Cosmic-Ray Electron and Positron Spectra with the Fermi Large Area Telescope

NASA Technical Reports Server (NTRS)

Ackermann, M.; Ajello, M.; Allafort, A.; Baldini, L.; Barbiellini, G.; Bastieri, D.; Bechtol, K.; Bellazzini, R.; Berenji, B.; Blandford, R. D.;

Greenhouse gases inventory and carbon balance of two dairy systems obtained from two methane-estimation methods.

PubMed

Cunha, C S; Lopes, N L; Veloso, C M; Jacovine, L A G; Tomich, T R; Pereira, L G R; Marcondes, M I

2016-11-15

The adoption of carbon inventories for dairy farms in tropical countries based on models developed from animals and diets of temperate climates is questionable. Thus, the objectives of this study were to estimate enteric methane (CH4) emissions through the SF6 tracer gas technique and through equations proposed by the Intergovernmental Panel on Climate Change (IPCC) Tier 2 and to calculate the inventory of greenhouse gas (GHG) emissions from two dairy systems. In addition, the carbon balance of these properties was estimated using enteric CH4 emissions obtained using both methodologies. In trial 1, the CH4 emissions were estimated from seven Holstein dairy cattle categories based on the SF6 tracer gas technique and on IPCC equations. The categories used in the study were prepubertal heifers (n=6); pubertal heifers (n=4); pregnant heifers (n=5); high-producing (n=6); medium-producing (n=5); low-producing (n=4) and dry cows (n=5). Enteric methane emission was higher for the category comprising prepubertal heifers when estimated by the equations proposed by the IPCC Tier 2. However, higher CH4 emissions were estimated by the SF6 technique in the categories including medium- and high-producing cows and dry cows. Pubertal heifers, pregnant heifers, and low-producing cows had equal CH4 emissions as estimated by both methods. In trial 2, two dairy farms were monitored for one year to identify all activities that contributed in any way to GHG emissions. The total emission from Farm 1 was 3.21t CO2e/animal/yr, of which 1.63t corresponded to enteric CH4. Farm 2 emitted 3.18t CO2e/animal/yr, with 1.70t of enteric CH4. IPCC estimations can underestimate CH4 emissions from some categories while overestimate others. However, considering the whole property, these discrepancies are offset and we would submit that the equations suggested by the IPCC properly estimate the total CH4 emission and carbon balance of the properties. Thus, the IPCC equations should be utilized with caution, and the herd composition should be analysed at the property level. When the carbon stock in pasture and other crops was considered, the carbon balance suggested that both farms are sustainable for GHG, by both methods. On the other hand, carbon balance without carbon stock, by both methods, suggests that farms emit more carbon than the system is capable of stock. Copyright © 2016 Elsevier B.V. All rights reserved.

SU-G-TeP4-03: A Multileaf Collimator Calibration and Quality Assurance Technique Using An Electronic Portal Imaging Device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lebron, S; Yan, G; Li, J

2016-06-15

Purpose: To develop an accurate and quick multileaf collimator (MLC) calibration and quality assurance technique using an electronic portal imaging device (EPID) Methods: The MLC models used include the MLCi and Agility (Elekta Ltd). This technique consists of two 22(L)x10(W) cm{sup 2} fields with 0{sup 0} and 180{sup 0} collimator angles centered to an offset EPID. The MLC opening is estimated by calculating the profile at the image’s center in the image’s horizontal direction. Scans in the image’s vertical direction were calculated every 20 pixels in the inner 70% of estimated MLC opening. The profiles’ edges were fitted with linearmore » equations to determine the image’s rotation angle. Then, crossline profiles were scanned at the center of each leaf taking into account the leaf’s width at isocenter and the rotation angle. The profiles’ edges determine the location of the leaves’ edges and these were subtracted from the reference leaf’s position in order to determine the relative leaf offsets. The edge location of all profiles was determined by using the parameterized gradient of the penumbra region. The technique was tested against an established diode array-based method, and for different MLC systems, patterns, gantry angles, days, energies, beam modalities and MLC openings. Results: The differences between the proposed and established methods were 0.26±0.19mm. The leaf offsets’ deviation was <0.3mm (5 months period). For pattern fields, the differences between predetermined and calculated offsets were 0.18±0.18mm. The leaf offset deviation of measurements with different energies and MLC openings were <0.1mm and <0.3mm, respectively. The differences between offsets of FF and FFF beams were 0.01±0.02mm (<0.07mm). The differences between the offsets at different gantry angles were 0.08±0.15mm. Conclusion: The proposed method proved to be accurate and efficient in calculating the relative leaf offsets. Parameterized field edge is essential to obtain accurate result by eliminating the noise from EPID.« less

Results of using the global positioning system to maintain the time and frequency synchronization in the Deep Space Network

NASA Technical Reports Server (NTRS)

Clements, P. A.; Kirk, A.; Unglaub, R.

1987-01-01

There are two hydrogen maser clocks located at each signal processing center (SPC) in the DSN. Close coordination of the time and frequency of the SPC clocks is needed to navigate spacecraft to the outer planets. A recent example was the Voyager spacecraft's encounter with Uranus in January 1986. The clocks were adjusted with the goal of minimizing time and frequency offsets between the SPCs at encounter. How time and frequency at each SPC is estimated using data acquired from the Global Positioning System Timing Receivers operating on the NBS-BIH (National Bureau of Standards-Bureau International de l'Heure) tracking schedule is described. These data are combined with other available timing receiver data to calculate the time offset estimates. The adjustment of the clocks is described. It was determined that long range hydrogen maser drift is quite predictable and adjustable within limits. This enables one to minimize time and frequency differences between the three SPCs for many months by matching the drift rates of the three standards. Data acquisition and processing techniques using a Kalman filter to make estimates of time and frequency offsets between the clocks at the SPCs and UTC(NBS) (Coordinated Universal Time realized at NBS) are described.

Greenhouse gas emissions and carbon sequestration by agroforestry systems in southeastern Brazil.

PubMed

Torres, Carlos Moreira Miquelino Eleto; Jacovine, Laércio Antônio Gonçalves; Nolasco de Olivera Neto, Sílvio; Fraisse, Clyde William; Soares, Carlos Pedro Boechat; de Castro Neto, Fernando; Ferreira, Lino Roberto; Zanuncio, José Cola; Lemes, Pedro Guilherme

2017-12-01

Agrosilvopastoral and silvopastoral systems can increase carbon sequestration, offset greenhouse gas (GHG) emissions and reduce the carbon footprint generated by animal production. The objective of this study was to estimate GHG emissions, the tree and grass aboveground biomass production and carbon storage in different agrosilvopastoral and silvopastoral systems in southeastern Brazil. The number of trees required to offset these emissions were also estimated. The GHG emissions were calculated based on pre-farm (e.g. agrochemical production, storage, and transportation), and on-farm activities (e.g. fertilization and machinery operation). Aboveground tree grass biomass and carbon storage in all systems was estimated with allometric equations. GHG emissions from the agroforestry systems ranged from 2.81 to 7.98 t CO 2 e ha -1 . Carbon storage in the aboveground trees and grass biomass were 54.6, 11.4, 25.7 and 5.9 t C ha -1 , and 3.3, 3.6, 3.8 and 3.3 t C ha -1 for systems 1, 2, 3 and 4, respectively. The number of trees necessary to offset the emissions ranged from 17 to 44 trees ha -1 , which was lower than the total planted in the systems. Agroforestry systems sequester CO 2 from the atmosphere and can help the GHG emission-reduction policy of the Brazilian government.

Measuring snow water equivalent from common-offset GPR records through migration velocity analysis

NASA Astrophysics Data System (ADS)

St. Clair, James; Holbrook, W. Steven

2017-12-01

Many mountainous regions depend on seasonal snowfall for their water resources. Current methods of predicting the availability of water resources rely on long-term relationships between stream discharge and snowpack monitoring at isolated locations, which are less reliable during abnormal snow years. Ground-penetrating radar (GPR) has been shown to be an effective tool for measuring snow water equivalent (SWE) because of the close relationship between snow density and radar velocity. However, the standard methods of measuring radar velocity can be time-consuming. Here we apply a migration focusing method originally developed for extracting velocity information from diffracted energy observed in zero-offset seismic sections to the problem of estimating radar velocities in seasonal snow from common-offset GPR data. Diffractions are isolated by plane-wave-destruction (PWD) filtering and the optimal migration velocity is chosen based on the varimax norm of the migrated image. We then use the radar velocity to estimate snow density, depth, and SWE. The GPR-derived SWE estimates are within 6 % of manual SWE measurements when the GPR antenna is coupled to the snow surface and 3-21 % of the manual measurements when the antenna is mounted on the front of a snowmobile ˜ 0.5 m above the snow surface.

A model of distributed phase aberration for deblurring phase estimated from scattering.

PubMed

Tillett, Jason C; Astheimer, Jeffrey P; Waag, Robert C

2010-01-01

Correction of aberration in ultrasound imaging uses the response of a point reflector or its equivalent to characterize the aberration. Because a point reflector is usually unavailable, its equivalent is obtained using statistical methods, such as processing reflections from multiple focal regions in a random medium. However, the validity of methods that use reflections from multiple points is limited to isoplanatic patches for which the aberration is essentially the same. In this study, aberration is modeled by an offset phase screen to relax the isoplanatic restriction. Methods are developed to determine the depth and phase of the screen and to use the model for compensation of aberration as the beam is steered. Use of the model to enhance the performance of the noted statistical estimation procedure is also described. Experimental results obtained with tissue-mimicking phantoms that implement different models and produce different amounts of aberration are presented to show the efficacy of these methods. The improvement in b-scan resolution realized with the model is illustrated. The results show that the isoplanatic patch assumption for estimation of aberration can be relaxed and that propagation-path characteristics and aberration estimation are closely related.

7 CFR 4288.135 - Unauthorized payments and offsets.

Code of Federal Regulations, 2014 CFR

2014-01-01

...-COOPERATIVE SERVICE AND RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE PAYMENT PROGRAMS Advanced Biofuel... unauthorized assistance has been made to an advanced biofuel producer under this Program, the Agency reserves... the producer. Upon determination that unauthorized assistance has been made to an advanced biofuel...

Seismic data enhancement and regularization using finite offset Common Diffraction Surface (CDS) stack

NASA Astrophysics Data System (ADS)

Garabito, German; Cruz, João Carlos Ribeiro; Oliva, Pedro Andrés Chira; Söllner, Walter

2017-01-01

The Common Reflection Surface stack is a robust method for simulating zero-offset and common-offset sections with high accuracy from multi-coverage seismic data. For simulating common-offset sections, the Common-Reflection-Surface stack method uses a hyperbolic traveltime approximation that depends on five kinematic parameters for each selected sample point of the common-offset section to be simulated. The main challenge of this method is to find a computationally efficient data-driven optimization strategy for accurately determining the five kinematic stacking parameters on which each sample of the stacked common-offset section depends. Several authors have applied multi-step strategies to obtain the optimal parameters by combining different pre-stack data configurations. Recently, other authors used one-step data-driven strategies based on a global optimization for estimating simultaneously the five parameters from multi-midpoint and multi-offset gathers. In order to increase the computational efficiency of the global optimization process, we use in this paper a reduced form of the Common-Reflection-Surface traveltime approximation that depends on only four parameters, the so-called Common Diffraction Surface traveltime approximation. By analyzing the convergence of both objective functions and the data enhancement effect after applying the two traveltime approximations to the Marmousi synthetic dataset and a real land dataset, we conclude that the Common-Diffraction-Surface approximation is more efficient within certain aperture limits and preserves at the same time a high image accuracy. The preserved image quality is also observed in a direct comparison after applying both approximations for simulating common-offset sections on noisy pre-stack data.

How to estimate carbon sequestration on small forest tracts estimate carbon sequestration on small forest tracts

Treesearch

Coeli M. Hoover; Richard A. Birdsey; Linda S. Heath; Susan L. Stout

2000-01-01

International climate change agreements may allow carbon stored as a result of afforestation and reforestation to be used to offset CO2 emissions. Monitoring the carbon sequestered or released through forest management activities thus becomes important. Estimating forest carbon storage is feasible even for nonindustrial private forestland (NIPF)...

Some observations on colocated and closely spaced strong ground-motion records of the 1999 Chi-Chi, Taiwan, earthquake

USGS Publications Warehouse

Wang, G.-Q.; Boore, D.M.; Igel, H.; Zhou, X.-Y.

2003-01-01

The digital accelerograph network installed in Taiwan produced a rich set of records from the 20 September 1999 Chi-Chi, Taiwan earthquake (Mw 7.6). Teledyne Geotech model A-800 and A-900A* digital accelerographs were colocated at 22 stations that recorded this event. Comparisons of the amplitudes, frequency content, and baseline offsets show that records from several of the A-800 accelerographs are considerably different than those from the colocated A-900A accelerographs. On this basis, and in view of the more thorough predeployment testing of the newer A-900A instruments, we recommend that the records from the A-800 instruments be used with caution in analyses of the mainshock and aftershocks. At the Hualien seismic station two A-900A and one A-800 instruments were colocated, along with a Global Positioning System instrument. Although the records from the two A-900A instruments are much more similar than those from a colocated A-800 instrument, both three-component records contain unpredictable baseline offsets, which produced completely unrealistic ground displacements derived from the accelerations by double integration, as do many of the strong-motion data from this event; the details of the baseline offsets differ considerably on the two three-component records. There are probably numerous sources of the baseline offsets, including sources external to the instruments, such as tilting or rotation of the ground, and sources internal to the instruments, such as electrical or mechanical hysteresis in the sensors. For the two colocated A-900A records at the Hualien seismic station, however, the differences in the baseline offsets suggest that the principal source is some transient disturbance within the instrument. The baseline offsets generally manifest themselves in the acceleration time series as pulses or steps, either singly or in combination. We find a 0.015-Hz low-cut filter can almost completely eliminate the effects of the baseline offsets, but then information regarding the permanent displacements is lost. The causative mechanisms of the baseline offsets are unknown presently. Hence, it is very difficult to recover the permanent displacements from the modern digital records, although for records close to large earthquakes, the signal-to-noise ratio should theoretically be adequate to obtain ground motions with periods of hundreds of seconds. This study reinforces our conclusion from previous studies that the sources of baseline offsets occurring in digital strong-motion records are very complex and often unpredictable, and that, therefore, it is difficult to remove the baseline effects to maximize the information content of the record. The baseline offsets only affect very long period motions (e.g., >20 sec), however, and therefore are of little or no engineering concern.

Experimental study on thrust and power of flapping-wing system based on rack-pinion mechanism.

PubMed

Nguyen, Tuan Anh; Vu Phan, Hoang; Au, Thi Kim Loan; Park, Hoon Cheol

2016-06-20

This experimental study investigates the effect of three parameters: wing aspect ratio (AR), wing offset, and flapping frequency, on thrust generation and power consumption of a flapping-wing system based on a rack-pinion mechanism. The new flapping-wing system is simple but robust, and is able to create a large flapping amplitude. The thrust measured by a load cell reveals that for a given power, the flapping-wing system using a higher wing AR produces larger thrust and higher flapping frequency at the wing offset of 0.15[Formula: see text] or 0.20[Formula: see text] ([Formula: see text] is the mean chord) than other wing offsets. Of the three parameters, the flapping frequency plays a more significant role on thrust generation than either the wing AR or the wing offset. Based on the measured thrusts, an empirical equation for thrust prediction is suggested, as a function of wing area, flapping frequency, flapping angle, and wing AR. The difference between the predicted and measured thrusts was less than 7%, which proved that the empirical equation for thrust prediction is reasonable. On average, the measured power consumption to flap the wings shows that 46.5% of the input power is spent to produce aerodynamic forces, 14.0% to overcome inertia force, 9.5% to drive the rack-pinion-based flapping mechanism, and 30.0% is wasted as the power loss of the installed motor. From the power analysis, it is found that the wing with an AR of 2.25 using a wing offset of 0.20[Formula: see text] showed the optimal power loading in the flapping-wing system. In addition, the flapping frequency of 25 Hz is recommended as the optimal frequency of the current flapping-wing system for high efficiency, which was 48.3%, using a wing with an AR of 2.25 and a wing offset of 0.20[Formula: see text] in the proposed design.

ENCODING OF TEMPORAL FEATURES OF AUDITORY STIMULI IN THE MEDIAL NUCLEUS OF THE TRAPEZOID BODY AND SUPERIOR PARAOLIVARY NUCLEUS OF THE RAT

PubMed Central

Kadner, Alexander; Berrebi, Albert S.

2008-01-01

Neurons in the superior paraolivary nucleus (SPON) respond to the offset of pure tones with a brief burst of spikes. Medial nucleus of the trapezoid body (MNTB) neurons, which inhibit the SPON, produce a sustained pure tone response followed by an offset response characterized by a period of suppressed spontaneous activity. This MNTB offset response is duration dependent and critical to the formation of SPON offset spikes (Kadner et al., 2006; Kulesza, Jr. et al., 2007). Here we examine the temporal resolution of the MNTB/SPON circuit by assessing its capability to i) detect gaps in tones, and ii) synchronize to sinusoidally amplitude modulated (SAM) tones. Gap detection was tested by presenting two identical pure tone markers interrupted by gaps ranging from 0–25 ms duration. SPON neurons responded to the offset of the leading marker even when the two markers were separated only by their ramps (i.e., a 0 ms gap); longer gap durations elicited progressively larger responses. MNTB neurons produced an offset response at gap durations of 2 ms or longer, with a subset of neurons responding to 0 ms gaps. SAM tone stimuli used the unit’s characteristic frequency as a carrier, and modulation rates ranged from 40–1160 Hz. MNTB neurons synchronized to modulation rates up to ~1 KHz, whereas spiking of SPON neurons decreased sharply at modulation rates ≥ 400 Hz. Modulation transfer functions based on spike count were all-pass for MNTB neurons and low-pass for SPON neurons; the modulation transfer functions based on vector strength were low-pass for both nuclei, with a steeper cut-off for SPON neurons. Thus, the MNTB/SPON circuit encodes episodes of low stimulus energy, such as gaps in pure tones and troughs in amplitude modulated tones. The output of this circuit consists of brief SPON spiking episodes; their potential effects on the auditory midbrain and forebrain are discussed. PMID:18155850

Intercontinental height datum connection with GOCE and GPS-levelling data

NASA Astrophysics Data System (ADS)

Gruber, T.; Gerlach, C.; Haagmans, R.

2012-12-01

In this study an attempt is made to establish height system datum connections based upon a gravity field and steady-state ocean circulation explorer (GOCE) gravity field model and a set of global positioning system (GPS) and levelling data. The procedure applied in principle is straightforward. First local geoid heights are obtained point wise from GPS and levelling data. Then the mean of these geoid heights is computed for regions nominally referring to the same height datum. Subsequently, these local mean geoid heights are compared with a mean global geoid from GOCE for the same region. This way one can identify an offset of the local to the global geoid per region. This procedure is applied to a number of regions distributed worldwide. Results show that the vertical datum offset estimates strongly depend on the nature of the omission error, i.e. the signal not represented in the GOCE model. For a smooth gravity field the commission error of GOCE, the quality of the GPS and levelling data and the averaging control the accuracy of the vertical datum offset estimates. In case the omission error does not cancel out in the mean value computation, because of a sub-optimal point distribution or a characteristic behaviour of the omitted part of the geoid signal, one needs to estimate a correction for the omission error from other sources. For areas with dense and high quality ground observations the EGM2008 global model is a good choice to estimate the omission error correction in theses cases. Relative intercontinental height datum offsets are estimated by applying this procedure between the United State of America (USA), Australia and Germany. These are compared to historical values provided in the literature and computed with the same procedure. The results obtained in this study agree on a level of 10 cm to the historical results. The changes mainly can be attributed to the new global geoid information from GOCE, rather than to the ellipsoidal heights or the levelled heights. These historical levelling data are still in use in many countries. This conclusion is supported by other results on the validation of the GOCE models.

A time and frequency synchronization method for CO-OFDM based on CMA equalizers

NASA Astrophysics Data System (ADS)

Ren, Kaixuan; Li, Xiang; Huang, Tianye; Cheng, Zhuo; Chen, Bingwei; Wu, Xu; Fu, Songnian; Ping, Perry Shum

2018-06-01

In this paper, an efficient time and frequency synchronization method based on a new training symbol structure is proposed for polarization division multiplexing (PDM) coherent optical orthogonal frequency division multiplexing (CO-OFDM) systems. The coarse timing synchronization is achieved by exploiting the correlation property of the first training symbol, and the fine timing synchronization is accomplished by using the time-domain symmetric conjugate of the second training symbol. Furthermore, based on these training symbols, a constant modulus algorithm (CMA) is proposed for carrier frequency offset (CFO) estimation. Theoretical analysis and simulation results indicate that the algorithm has the advantages of robustness to poor optical signal-to-noise ratio (OSNR) and chromatic dispersion (CD). The frequency offset estimation range can achieve [ -Nsc/2 ΔfN , + Nsc/2 ΔfN ] GHz with the mean normalized estimation error below 12 × 10-3 even under the condition of OSNR as low as 10 dB.

Multiple Two-Way Time Message Exchange (TTME) Time Synchronization for Bridge Monitoring Wireless Sensor Networks

PubMed Central

Shi, Fanrong; Tuo, Xianguo; Yang, Simon X.; Li, Huailiang; Shi, Rui

2017-01-01

Wireless sensor networks (WSNs) have been widely used to collect valuable information in Structural Health Monitoring (SHM) of bridges, using various sensors, such as temperature, vibration and strain sensors. Since multiple sensors are distributed on the bridge, accurate time synchronization is very important for multi-sensor data fusion and information processing. Based on shape of the bridge, a spanning tree is employed to build linear topology WSNs and achieve time synchronization in this paper. Two-way time message exchange (TTME) and maximum likelihood estimation (MLE) are employed for clock offset estimation. Multiple TTMEs are proposed to obtain a subset of TTME observations. The time out restriction and retry mechanism are employed to avoid the estimation errors that are caused by continuous clock offset and software latencies. The simulation results show that the proposed algorithm could avoid the estimation errors caused by clock drift and minimize the estimation error due to the large random variable delay jitter. The proposed algorithm is an accurate and low complexity time synchronization algorithm for bridge health monitoring. PMID:28471418

Multiple Two-Way Time Message Exchange (TTME) Time Synchronization for Bridge Monitoring Wireless Sensor Networks.

PubMed

Shi, Fanrong; Tuo, Xianguo; Yang, Simon X; Li, Huailiang; Shi, Rui

2017-05-04

Wireless sensor networks (WSNs) have been widely used to collect valuable information in Structural Health Monitoring (SHM) of bridges, using various sensors, such as temperature, vibration and strain sensors. Since multiple sensors are distributed on the bridge, accurate time synchronization is very important for multi-sensor data fusion and information processing. Based on shape of the bridge, a spanning tree is employed to build linear topology WSNs and achieve time synchronization in this paper. Two-way time message exchange (TTME) and maximum likelihood estimation (MLE) are employed for clock offset estimation. Multiple TTMEs are proposed to obtain a subset of TTME observations. The time out restriction and retry mechanism are employed to avoid the estimation errors that are caused by continuous clock offset and software latencies. The simulation results show that the proposed algorithm could avoid the estimation errors caused by clock drift and minimize the estimation error due to the large random variable delay jitter. The proposed algorithm is an accurate and low complexity time synchronization algorithm for bridge health monitoring.

Theoretical prediction of the band offsets at the ZnO/anatase TiO2 and GaN/ZnO heterojunctions using the self-consistent ab initio DFT/GGA-1/2 method.

PubMed

Fang, D Q; Zhang, S L

2016-01-07

The band offsets of the ZnO/anatase TiO2 and GaN/ZnO heterojunctions are calculated using the density functional theory/generalized gradient approximation (DFT/GGA)-1/2 method, which takes into account the self-energy corrections and can give an approximate description to the quasiparticle characteristics of the electronic structure of semiconductors. We present the results of the ionization potential (IP)-based and interfacial offset-based band alignments. In the interfacial offset-based band alignment, to get the natural band offset, we use the surface calculations to estimate the change of reference level due to the interfacial strain. Based on the interface models and GGA-1/2 calculations, we find that the valence band maximum and conduction band minimum of ZnO, respectively, lie 0.64 eV and 0.57 eV above those of anatase TiO2, while lie 0.84 eV and 1.09 eV below those of GaN, which agree well with the experimental data. However, a large discrepancy exists between the IP-based band offset and the calculated natural band offset, the mechanism of which is discussed. Our results clarify band alignment of the ZnO/anatase TiO2 heterojunction and show good agreement with the GW calculations for the GaN/ZnO heterojunction.

Right-lateral shear across Iran and kinematic change in the Arabia-Eurasia collision zone

NASA Astrophysics Data System (ADS)

Allen, Mark B.; Kheirkhah, Monireh; Emami, Mohammad H.; Jones, Stuart J.

2011-02-01

New offset determinations for right-lateral strike-slip faults in Iran revise the kinematics of the Arabia-Eurasia collision, by indicating along-strike lengthening of the collision zone before a change to the present kinematic regime at ˜5 Ma. A series of right-lateral strike-slip faults is present across the Turkish-Iranian plateau between 48°E and 57°E. Fault strikes vary between NW-SE and NNW-SSE. Several of the faults are seismically active and/or have geomorphic evidence for Holocene slip. None of the faults affects the GPS-derived regional velocity field, indicating active slip rates are ≤2 mm yr-1. We estimate total offsets for these faults from displaced geological and geomorphic markers, based on observations from satellite imagery, digital topography, geology maps and our own fieldwork observations, and combine these results with published estimates for fault displacement. Total right-lateral offset of the Dehu, Anar, Deh Shir, Kashan, Ab-Shirin-Shurab, Kousht Nousrat, Qom, Bid Hand, Indes, Soltanieh and Takab faults is ˜250 km. Other faults (North Zanjan, Saveh, Jorjafk, Rafsanjan, Kuh Banan and Behabad) have unknown or highly uncertain amounts of slip. Collectively, these faults are inferred to have accommodated part of the Arabia-Eurasia convergence. Three roles are possible, which are not mutually exclusive: (1) shortening via anticlockwise, vertical axis rotations; (2) northward movement of Iranian crust with respect to stable Afghanistan to the east; (3) combination with coeval NW-SE thrusts in the Turkish-Iranian plateau, to produce north-south plate convergence (`strain partitioning'). This strike-slip faulting across Iran requires along-strike lengthening of the collision zone. This was possible until the Pliocene (≤ 5 Ma), when the Afghan crust collided with the western margin of the Indian plate, thereby sealing off a free face at the eastern side of the Arabia-Eurasia collision zone. Continuing Arabia-Eurasia plate convergence had to be accommodated in new ways and new areas, leading to the present pattern of faulting from eastern Iran to western Turkey, and involving the westward transport (`escape') of Anatolia and the concentration of thrusting in the Zagros and Alborz mountains.

How do long-offset oceanic transforms adapt to plate motion changes? The example of the Western Pacific-Antarctic plate boundary

NASA Astrophysics Data System (ADS)

Lodolo, Emanuele; Coren, Franco; Ben-Avraham, Zvi

2013-03-01

Oceanic transform faults respond to changes in the direction of relative plate motion. Studies have shown that short-offset transforms generally adjust with slight bends near the ridge axis, while long-offset ones have a remarkably different behavior. The western Pacific-Antarctic plate boundary highlights these differences. A set of previously unpublished seismic profiles, in combination with magnetic anomaly identifications, shows how across a former, ~1250 km long transform (the Emerald Fracture Zone), plate motion changes have produced a complex geometric readjustment. Three distinct sections are recognized along this plate boundary: an eastern section, characterized by parallel, multiple fault strand lineaments; a central section, shallower than the rest of the ridge system, overprinted by a mantle plume track; and a western section, organized in a cascade of short spreading axes/transform lineaments. This configuration was produced by changes that occurred since 30 Ma in the Australia-Pacific relative plate motion, combined with a gradual clockwise change in Pacific-Antarctic plate motion. These events caused extension along the former Emerald Fracture Zone, originally linking the Pacific-Antarctic spreading ridge system with the Southeast Indian ridge. Then an intra-transform propagating ridge started to develop in response to a ~6 Ma change in the Pacific-Antarctic spreading direction. The close proximity of the Euler poles of rotation amplified the effects of the geometric readjustments that occurred along the transform system. This analysis shows that when a long-offset transform older than 20 Ma is pulled apart by changes in spreading velocity vectors, it responds with the development of multiple discrete, parallel fault strands, whereas in younger lithosphere, locally modified by thermal anisotropies, tensional stresses generate an array of spreading axes offset by closely spaced transforms.

Cumulative biological impacts framework for solar energy projects in the California Desert

USGS Publications Warehouse

Davis, Frank W.; Kreitler, Jason R.; Soong, Oliver; Stoms, David M.; Dashiell, Stephanie; Hannah, Lee; Wilkinson, Whitney; Dingman, John

2013-01-01

This project developed analytical approaches, tools and geospatial data to support conservation planning for renewable energy development in the California deserts. Research focused on geographical analysis to avoid, minimize and mitigate the cumulative biological effects of utility-scale solar energy development. A hierarchical logic model was created to map the compatibility of new solar energy projects with current biological conservation values. The research indicated that the extent of compatible areas is much greater than the estimated land area required to achieve 2040 greenhouse gas reduction goals. Species distribution models were produced for 65 animal and plant species that were of potential conservation significance to the Desert Renewable Energy Conservation Plan process. These models mapped historical and projected future habitat suitability using 270 meter resolution climate grids. The results were integrated into analytical frameworks to locate potential sites for offsetting project impacts and evaluating the cumulative effects of multiple solar energy projects. Examples applying these frameworks in the Western Mojave Desert ecoregion show the potential of these publicly-available tools to assist regional planning efforts. Results also highlight the necessity to explicitly consider projected land use change and climate change when prioritizing areas for conservation and mitigation offsets. Project data, software and model results are all available online.

Analysis of HY2A precise orbit determination using DORIS

NASA Astrophysics Data System (ADS)

Gao, Fan; Peng, Bibo; Zhang, Yu; Evariste, Ngatchou Heutchi; Liu, Jihua; Wang, Xiaohui; Zhong, Min; Lin, Mingsen; Wang, Nazi; Chen, Runjing; Xu, Houze

2015-03-01

HY2A is the first Chinese marine dynamic environment satellite. The payloads include a radar altimeter to measure the sea surface height in combination with a high precision orbit to be determined from tracking data. Onboard satellite tracking includes GPS, SLR, and the DORIS DGXX receiver which delivers phase and pseudo-range measurements. CNES releases raw phase and pseudo-range measurements with RINEX DORIS 3.0 format and pre-processed Doppler range-rate with DORIS 2.2 data format. However, the VMSI software package developed by Van Martin Systems, Inc which is used to estimate HY2A DORIS orbits can only process Doppler range-rate but not the DORIS phase data which are available with much shorter latency. We have proposed a method of constructing the phase increment data, which are similar to range-rate data, from RINEX DORIS 3.0 phase data. We compute the HY2A orbits from June, 2013 to August, 2013 using the POD strategy described in this paper based on DORIS 2.2 range-rate data and our reconstructed phase increment data. The estimated orbits are evaluated by comparing with the CNES precise orbits and SLR residuals. Our DORIS-only orbits agree with the precise GPS + SLR + DORIS CNES orbits radially at 1-cm and about 3-cm in the other two directions. SLR test with the 50° cutoff elevation shows that the CNES orbit can achieve about 1.1-cm accuracy in radial direction and our DORIS-only POD solutions are slightly worse. In addition, other HY2A DORIS POD concerns are discussed in this paper. Firstly, we discuss the frequency offset values provided with the RINEX data and find that orbit accuracy for the case when the frequency offset is applied is worse than when it is not applied. Secondly, HY2A DORIS antenna z-offsets are estimated using two kinds of measurements from June, 2013 to August, 2013. The results show that the measurement errors contribute a total of about 2-cm difference of estimated z-offset. Finally, we estimate HY2A orbits selecting 3 days with severe geomagnetic storm activity and SLR residuals suggest that estimating a drag coefficient every 6 h without any constraint is sufficient for maintaining orbit accuracy.

7 CFR 4288.135 - Unauthorized payments and offsets.

Code of Federal Regulations, 2012 CFR

2012-01-01

...-COOPERATIVE SERVICE AND RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE PAYMENT PROGRAMS Advanced Biofuel... assistance has been made to an advanced biofuel producer under this Program, the Agency reserves the right to... determination that unauthorized assistance has been made to an advanced biofuel producer under this Program, the...

7 CFR 4288.135 - Unauthorized payments and offsets.

Code of Federal Regulations, 2013 CFR

2013-01-01

...-COOPERATIVE SERVICE AND RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE PAYMENT PROGRAMS Advanced Biofuel... assistance has been made to an advanced biofuel producer under this Program, the Agency reserves the right to... determination that unauthorized assistance has been made to an advanced biofuel producer under this Program, the...

Roll-Tilt Perception Using a Somatosensory Bar Task

NASA Technical Reports Server (NTRS)

Black, F. O.; Wade, S. W.; Arshi, A.

1999-01-01

Visual estimates of roll-tilt perception during static roll-tilt are confounded by an offset due to the ocular counterroll that simultaneously occurs. An alternative, non-visual ('somatosensory') measure of roll-tilt perception was developed which is not contaminated by this offset. The aims of this study were to determine: 1) inter-subject variability of somatosensory settings across test session in normal subjects and patients with unilateral or bilateral vestibular loss and 2) intra-subject variability of settings across test session in normal subjects.

Consequences of alternative tree-level biomass estimation procedures on U.S. forest carbon stock estimates

Treesearch

Grant M. Domke; Christopher W. Woodall; James E. Smith; James A. Westfall; Ronald E. McRoberts

2012-01-01

Forest ecosystems are the largest terrestrial carbon sink on earth and their management has been recognized as a relatively cost-effective strategy for offsetting greenhouse gas emissions. Forest carbon stocks in the U.S. are estimated using data from the USDA Forest Service, Forest Inventory and Analysis (FIA) program. In an attempt to balance accuracy with...

Interpretation of magnetization transfer from inhomogeneously broadened lines (ihMT) in tissues as a dipolar order effect within motion restricted molecules

NASA Astrophysics Data System (ADS)

Varma, G.; Girard, O. M.; Prevost, V. H.; Grant, A. K.; Duhamel, G.; Alsop, D. C.

2015-11-01

Comparison of off-resonance saturation with single and dual frequency irradiation indicates a contribution of inhomogeneously broadened lines to magnetization transfer in tissues. This inhomogeneous magnetization transfer (ihMT) phenomenon can be exploited to produce images that highlight tissues containing myelin, in vivo. Here, a model for ihMT is described that includes dipolar order effects from magnetization associated with motion-restricted macromolecules. In this model, equal irradiation at positive and negative frequency offsets eliminates dipolar order and achieves greater saturation than irradiation at a single offset frequency using the same power. Fitting of mouse and human volunteer brain data at different irradiation powers and offset frequencies was performed to assess the relevance of the model and approximate tissue parameters. A key parameter in determining ihMT signal was found to be the relaxation time T1D associated with the dipolar order reservoir and the fraction f of the semi-solid, bound magnetization that possessed a nonzero T1D. Indeed, better fits of myelinated tissue were achieved when assuming f ≠ 1. From such fits, estimated T1Ds of mice in the white matter, (34 ± 14)ms, were much longer than in muscle, T1D = (1 ± 1)ms and the average f from white matter volunteer data was 2.2 times greater than that in grey matter. The combination of f and longer T1Ds was primarily responsible for the much higher ihMT in myelinated tissues, and provided explanation for the species variation. This dipolar order ihMT model should help guide future research, pulse sequence optimization, and clinical applications.

Faulting and hydration of the Juan de Fuca plate system

NASA Astrophysics Data System (ADS)

Nedimović, Mladen R.; Bohnenstiehl, DelWayne R.; Carbotte, Suzanne M.; Pablo Canales, J.; Dziak, Robert P.

2009-06-01

Multichannel seismic observations provide the first direct images of crustal scale normal faults within the Juan de Fuca plate system and indicate that brittle deformation extends up to ~ 200 km seaward of the Cascadia trench. Within the sedimentary layering steeply dipping faults are identified by stratigraphic offsets, with maximum throws of 110 ± 10 m found near the trench. Fault throws diminish both upsection and seaward from the trench. Long-term throw rates are estimated to be 13 ± 2 mm/kyr. Faulted offsets within the sedimentary layering are typically linked to larger offset scarps in the basement topography, suggesting reactivation of the normal fault systems formed at the spreading center. Imaged reflections within the gabbroic igneous crust indicate swallowing fault dips at depth. These reflections require local alteration to produce an impedance contrast, indicating that the imaged fault structures provide pathways for fluid transport and hydration. As the depth extent of imaged faulting within this young and sediment insulated oceanic plate is primarily limited to approximately Moho depths, fault-controlled hydration appears to be largely restricted to crustal levels. If dehydration embrittlement is an important mechanism for triggering intermediate-depth earthquakes within the subducting slab, then the limited occurrence rate and magnitude of intraslab seismicity at the Cascadia margin may in part be explained by the limited amount of water imbedded into the uppermost oceanic mantle prior to subduction. The distribution of submarine earthquakes within the Juan de Fuca plate system indicates that propagator wake areas are likely to be more faulted and therefore more hydrated than other parts of this plate system. However, being largely restricted to crustal levels, this localized increase in hydration generally does not appear to have a measurable effect on the intraslab seismicity along most of the subducted propagator wakes at the Cascadia margin.

Neuroendocrine aspects of primary endogenous depression. XV: Mathematical modeling of nocturnal melatonin secretion in major depressives and normal controls.

PubMed

Sekula, L K; Lucke, J F; Heist, E K; Czambel, R K; Rubin, R T

1997-03-24

We previously reported a trend toward a higher mean nocturnal serum melatonin (MEL) concentration, based on 30-min blood sampling over 24 h, in 23 female definite endogenous depressive compared to 23 matched normal female control subjects, and no significant difference in 15 male depressives compared to their controls (Rubin et al., 1992). In both groups of patients vs. their controls, there also were trends toward an earlier MEL rise time, by about 30 min, and a later MEL peak time, by about 90 min. Because the offset of MEL secretion was not estimated in that study, the total duration of MEL secretion could not be determined. To further delineate the nocturnal MEL secretion curve, we modeled the MEL data by a linear-Beta model, a four-parameter adaptation of the Beta function. One parameter accounted-for baseline (diurnal) MEL concentration, two accounted for the shapes of the ascending and descending phases of the nocturnal secretion curve, and the fourth accounted for the area under the curve. The model permitted estimation of the start, peak, and end times of nocturnal MEL secretion. There again was a trend toward a higher mean nocturnal MEL concentration in the female depressives compared to their matched controls. There were no significant patient-control differences in secretion onset or peak times in either the women or the men except for nocturnal MEL offset time: the female patients had a trend toward a later offset time, by about 40 min, than their controls; this difference was not present in the men. With women and men analyzed together, the difference in nocturnal MEL offset time between patients and controls just reached significance (P < 0.05). The linear-Beta model appears to satisfactorily fit the MEL data and provides estimators of the onset, peak, and offset times of the activation phase of MEL secretion. This model may be applicable to more severely skewed 24-h hormone secretion curves, such as ACTH and cortisol.

Advances in 3D soil mapping and water content estimation using multi-channel ground-penetrating radar

NASA Astrophysics Data System (ADS)

Moysey, S. M.

2011-12-01

Multi-channel ground-penetrating radar systems have recently become widely available, thereby opening new possibilities for shallow imaging of the subsurface. One advantage of these systems is that they can significantly reduce survey times by simultaneously collecting multiple lines of GPR reflection data. As a result, it is becoming more practical to complete 3D surveys - particularly in situations where the subsurface undergoes rapid changes, e.g., when monitoring infiltration and redistribution of water in soils. While 3D and 4D surveys can provide a degree of clarity that significantly improves interpretation of the subsurface, an even more powerful feature of the new multi-channel systems for hydrologists is their ability to collect data using multiple antenna offsets. Central mid-point (CMP) surveys have been widely used to estimate radar wave velocities, which can be related to water contents, by sequentially increasing the distance, i.e., offset, between the source and receiver antennas. This process is highly labor intensive using single-channel systems and therefore such surveys are often only performed at a few locations at any given site. In contrast, with multi-channel GPR systems it is possible to physically arrange an array of antennas at different offsets, such that a CMP-style survey is performed at every point along a radar transect. It is then possible to process this data to obtain detailed maps of wave velocity with a horizontal resolution on the order of centimeters. In this talk I review concepts underlying multi-channel GPR imaging with an emphasis on multi-offset profiling for water content estimation. Numerical simulations are used to provide examples that illustrate situations where multi-offset GPR profiling is likely to be successful, with an emphasis on considering how issues like noise, soil heterogeneity, vertical variations in water content and weak reflection returns affect algorithms for automated analysis of the data. Overall, the ideal situation occurs when distinct, strong reflections are obtained from flat lying interfaces. To evaluate this idea in the field, data were collected from an agricultural field in the Clemson Experimental Forest in South Carolina and a restored floodplain at the East Branch Pecatonica River Restoration Observatory in Wisconsin using a pulseEKKO Pro GPR with 12 channels containing 500MHz antennas with offsets between 0.2-1.5m. The GPR data collection was found to be extremely efficient, allowing for an equivalent of over 12km of data to be collected within a day. While the two sites are significantly different, with contrasts ranging from soil structure to attenuation characteristics, the results illustrate that it is possible to obtain meaningful information about soil variability using multi-offset GPR profiling even at sites with non-ideal conditions.

Effects of energy chirp on bunch length measurement in linear accelerator beams

NASA Astrophysics Data System (ADS)

Sabato, L.; Arpaia, P.; Giribono, A.; Liccardo, A.; Mostacci, A.; Palumbo, L.; Vaccarezza, C.; Variola, A.

2017-08-01

The effects of assumptions about bunch properties on the accuracy of the measurement method of the bunch length based on radio frequency deflectors (RFDs) in electron linear accelerators (LINACs) are investigated. In particular, when the electron bunch at the RFD has a non-negligible energy chirp (i.e. a correlation between the longitudinal positions and energies of the particle), the measurement is affected by a deterministic intrinsic error, which is directly related to the RFD phase offset. A case study on this effect in the electron LINAC of a gamma beam source at the Extreme Light Infrastructure-Nuclear Physics (ELI-NP) is reported. The relative error is estimated by using an electron generation and tracking (ELEGANT) code to define the reference measurements of the bunch length. The relative error is proved to increase linearly with the RFD phase offset. In particular, for an offset of {{7}\\circ} , corresponding to a vertical centroid offset at a screen of about 1 mm, the relative error is 4.5%.

Cost-offsets of prescription drug expenditures: data analysis via a copula-based bivariate dynamic hurdle model.

PubMed

Deb, Partha; Trivedi, Pravin K; Zimmer, David M

2014-10-01

In this paper, we estimate a copula-based bivariate dynamic hurdle model of prescription drug and nondrug expenditures to test the cost-offset hypothesis, which posits that increased expenditures on prescription drugs are offset by reductions in other nondrug expenditures. We apply the proposed methodology to data from the Medical Expenditure Panel Survey, which have the following features: (i) the observed bivariate outcomes are a mixture of zeros and continuously measured positives; (ii) both the zero and positive outcomes show state dependence and inter-temporal interdependence; and (iii) the zeros and the positives display contemporaneous association. The point mass at zero is accommodated using a hurdle or a two-part approach. The copula-based approach to generating joint distributions is appealing because the contemporaneous association involves asymmetric dependence. The paper studies samples categorized by four health conditions: arthritis, diabetes, heart disease, and mental illness. There is evidence of greater than dollar-for-dollar cost-offsets of expenditures on prescribed drugs for relatively low levels of spending on drugs and less than dollar-for-dollar cost-offsets at higher levels of drug expenditures. Copyright © 2013 John Wiley & Sons, Ltd.

Potential for ag residue collection, economics and environmental benefits

NASA Astrophysics Data System (ADS)

Hettenhaus, J. R.

2003-12-01

Removing excess corn stover and cereal straws after erosion requirements have been satisfied offers much potential as a renewable feedstock for initial biorefineries, producing fuels, chemicals and materials while reducing crop inputs, increasing farm income and offsetting greenhouse gas emissions. Two biorefinery site studies are presented for the production of fuel ethanol: SW Nebraska and Western Oklahoma. Results include excess available, delivered cost, net income to the farmer, improved SOM from move to no-till and GHG reduction from fossil fuel offset

Quantitative Gait Measurement With Pulse-Doppler Radar for Passive In-Home Gait Assessment

PubMed Central

Skubic, Marjorie; Rantz, Marilyn; Cuddihy, Paul E.

2014-01-01

In this paper, we propose a pulse-Doppler radar system for in-home gait assessment of older adults. A methodology has been developed to extract gait parameters including walking speed and step time using Doppler radar. The gait parameters have been validated with a Vicon motion capture system in the lab with 13 participants and 158 test runs. The study revealed that for an optimal step recognition and walking speed estimation, a dual radar set up with one radar placed at foot level and the other at torso level is necessary. An excellent absolute agreement with intraclass correlation coefficients of 0.97 was found for step time estimation with the foot level radar. For walking speed, although both radars show excellent consistency they all have a system offset compared to the ground truth due to walking direction with respect to the radar beam. The torso level radar has a better performance (9% offset on average) in the speed estimation compared to the foot level radar (13%–18% offset). Quantitative analysis has been performed to compute the angles causing the systematic error. These lab results demonstrate the capability of the system to be used as a daily gait assessment tool in home environments, useful for fall risk assessment and other health care applications. The system is currently being tested in an unstructured home environment. PMID:24771566

Quantitative gait measurement with pulse-Doppler radar for passive in-home gait assessment.

PubMed

Wang, Fang; Skubic, Marjorie; Rantz, Marilyn; Cuddihy, Paul E

2014-09-01

In this paper, we propose a pulse-Doppler radar system for in-home gait assessment of older adults. A methodology has been developed to extract gait parameters including walking speed and step time using Doppler radar. The gait parameters have been validated with a Vicon motion capture system in the lab with 13 participants and 158 test runs. The study revealed that for an optimal step recognition and walking speed estimation, a dual radar set up with one radar placed at foot level and the other at torso level is necessary. An excellent absolute agreement with intraclass correlation coefficients of 0.97 was found for step time estimation with the foot level radar. For walking speed, although both radars show excellent consistency they all have a system offset compared to the ground truth due to walking direction with respect to the radar beam. The torso level radar has a better performance (9% offset on average) in the speed estimation compared to the foot level radar (13%-18% offset). Quantitative analysis has been performed to compute the angles causing the systematic error. These lab results demonstrate the capability of the system to be used as a daily gait assessment tool in home environments, useful for fall risk assessment and other health care applications. The system is currently being tested in an unstructured home environment.

Estimating national landfill methane emissions: an application of the 2006 Intergovernmental Panel on Climate Change Waste Model in Panama.

PubMed

Weitz, Melissa; Coburn, Jeffrey B; Salinas, Edgar

2008-05-01

This paper estimates national methane emissions from solid waste disposal sites in Panama over the time period 1990-2020 using both the 2006 Intergovernmental Panel on Climate Change (IPCC) Waste Model spreadsheet and the default emissions estimate approach presented in the 1996 IPCC Good Practice Guidelines. The IPCC Waste Model has the ability to calculate emissions from a variety of solid waste disposal site types, taking into account country- or region-specific waste composition and climate information, and can be used with a limited amount of data. Countries with detailed data can also run the model with country-specific values. The paper discusses methane emissions from solid waste disposal; explains the differences between the two methodologies in terms of data needs, assumptions, and results; describes solid waste disposal circumstances in Panama; and presents the results of this analysis. It also demonstrates the Waste Model's ability to incorporate landfill gas recovery data and to make projections. The former default method methane emissions estimates are 25 Gg in 1994, and range from 23.1 Gg in 1990 to a projected 37.5 Gg in 2020. The Waste Model estimates are 26.7 Gg in 1994, ranging from 24.6 Gg in 1990 to 41.6 Gg in 2020. Emissions estimates for Panama produced by the new model were, on average, 8% higher than estimates produced by the former default methodology. The increased estimate can be attributed to the inclusion of all solid waste disposal in Panama (as opposed to only disposal in managed landfills), but the increase was offset somewhat by the different default factors and regional waste values between the 1996 and 2006 IPCC guidelines, and the use of the first-order decay model with a time delay for waste degradation in the IPCC Waste Model.

Financial development and oil resource abundance-growth relations: evidence from panel data.

PubMed

Law, Siong Hook; Moradbeigi, Maryam

2017-10-01

This study investigates whether financial development dampens the negative impact of oil resource abundance on economic growth. Because of substantial cross-sectional dependence in our data, which contain a core sample of 63 oil-producing countries from 1980 through 2010, we use the common correlated effect mean group (CCEMG) estimator to account for the high degree of heterogeneity and drop the outlier countries. The empirical results reveal that oil resource abundance affects the growth rate in output contingent on the degree of development in financial markets. More developed financial markets can channel the revenues from oil into more productive activities and thus offset the negative effects of oil resource abundance on economic growth. Thus, better financial development can reverse resource curse or enhance resource blessing in oil-rich economies.

Measurement of separate cosmic-ray electron and positron spectra with the fermi large area telescope.

PubMed

Ackermann, M; Ajello, M; Allafort, A; Atwood, W B; Baldini, L; Barbiellini, G; Bastieri, D; Bechtol, K; Bellazzini, R; Berenji, B; Blandford, R D; Bloom, E D; Bonamente, E; Borgland, A W; Bouvier, A; Bregeon, J; Brigida, M; Bruel, P; Buehler, R; Buson, S; Caliandro, G A; Cameron, R A; Caraveo, P A; Casandjian, J M; Cecchi, C; Charles, E; Chekhtman, A; Cheung, C C; Chiang, J; Ciprini, S; Claus, R; Cohen-Tanugi, J; Conrad, J; Cutini, S; de Angelis, A; de Palma, F; Dermer, C D; Digel, S W; do Couto E Silva, E; Drell, P S; Drlica-Wagner, A; Favuzzi, C; Fegan, S J; Ferrara, E C; Focke, W B; Fortin, P; Fukazawa, Y; Funk, S; Fusco, P; Gargano, F; Gasparrini, D; Germani, S; Giglietto, N; Giommi, P; Giordano, F; Giroletti, M; Glanzman, T; Godfrey, G; Grenier, I A; Grove, J E; Guiriec, S; Gustafsson, M; Hadasch, D; Harding, A K; Hayashida, M; Hughes, R E; Jóhannesson, G; Johnson, A S; Kamae, T; Katagiri, H; Kataoka, J; Knödlseder, J; Kuss, M; Lande, J; Latronico, L; Lemoine-Goumard, M; Llena Garde, M; Longo, F; Loparco, F; Lovellette, M N; Lubrano, P; Madejski, G M; Mazziotta, M N; McEnery, J E; Michelson, P F; Mitthumsiri, W; Mizuno, T; Moiseev, A A; Monte, C; Monzani, M E; Morselli, A; Moskalenko, I V; Murgia, S; Nakamori, T; Nolan, P L; Norris, J P; Nuss, E; Ohno, M; Ohsugi, T; Okumura, A; Omodei, N; Orlando, E; Ormes, J F; Ozaki, M; Paneque, D; Parent, D; Pesce-Rollins, M; Pierbattista, M; Piron, F; Pivato, G; Porter, T A; Rainò, S; Rando, R; Razzano, M; Razzaque, S; Reimer, A; Reimer, O; Reposeur, T; Ritz, S; Romani, R W; Roth, M; Sadrozinski, H F-W; Sbarra, C; Schalk, T L; Sgrò, C; Siskind, E J; Spandre, G; Spinelli, P; Strong, A W; Takahashi, H; Takahashi, T; Tanaka, T; Thayer, J G; Thayer, J B; Tibaldo, L; Tinivella, M; Torres, D F; Tosti, G; Troja, E; Uchiyama, Y; Usher, T L; Vandenbroucke, J; Vasileiou, V; Vianello, G; Vitale, V; Waite, A P; Winer, B L; Wood, K S; Wood, M; Yang, Z; Zimmer, S

2012-01-06

We measured separate cosmic-ray electron and positron spectra with the Fermi Large Area Telescope. Because the instrument does not have an onboard magnet, we distinguish the two species by exploiting Earth's shadow, which is offset in opposite directions for opposite charges due to Earth's magnetic field. We estimate and subtract the cosmic-ray proton background using two different methods that produce consistent results. We report the electron-only spectrum, the positron-only spectrum, and the positron fraction between 20 and 200 GeV. We confirm that the fraction rises with energy in the 20-100 GeV range. The three new spectral points between 100 and 200 GeV are consistent with a fraction that is continuing to rise with energy.

Measurement of Separate Cosmic-Ray Electron and Positron Spectra with the Fermi Large Area Telescope

NASA Technical Reports Server (NTRS)

Ferrara, E. C.; Harding, A. K.; McEnery, J. E.; Moiseev, A. A.; Ackemann, M.

2012-01-01

We measured separate cosmic-ray electron and positron spectra with the Fermi Large Area Telescope. Because the instrument does not have an onboard magnet, we distinguish the two species by exploiting Earth's shadow, which, is offset in opposite directions for opposite charges due to Earth's magnetic field. We estimate and subtract the cosmic-ray proton background using two different methods that produce consistent results. We report the electron-only spectrum, the positron-only spectrum, and the positron fraction between 20 and 200 Ge V. We confirm that the fraction rises with energy in the 20-100 Ge V range. The three new spectral points between 100 and 200 GeV are consistent with a fraction that is continuing to rise with energy.

Baseline requirements can hinder trades in water quality trading programs: Evidence from the Conestoga watershed.

PubMed

Ghosh, Gaurav; Ribaudo, Marc; Shortle, James

2011-08-01

The U.S. Environmental Protection Agency (USEPA) and the U.S. Department of Agriculture (USDA) are promoting point/nonpoint trading as a way of reducing the costs of meeting water quality goals. Farms can create offsets by implementing management practices such as conservation tillage, nutrient management and buffer strips. To be eligible to sell offsets or credits, farmers must first comply with baseline requirements. USEPA guidance recommends that the baseline for nonpoint sources be management practices that are consistent with the water quality goal. A farmer would not be able to create offsets until the minimum practice standards are met. An alternative baseline is those practices being implemented at the time the trading program starts, or when the farmer enters the program. The selection of the baseline affects the efficiency and equity of the trading program. It has major implications for which farmers benefit from trading, the cost of nonpoint source offsets, and ultimately the number of offsets that nonpoint sources can sell to regulated point sources. We use a simple model of the average profit-maximizing dairy farmer operating in the Conestoga watershed in Pennsylvania to evaluate the implications of baseline requirements on the cost and quantity of offsets that can be produced for sale in a water quality trading market, and which farmers benefit most from trading. Published by Elsevier Ltd.

X-Ray Detection and Processing Models for Spacecraft Navigation and Timing

NASA Technical Reports Server (NTRS)

Sheikh, Suneel; Hanson, John

2013-01-01

The current primary method of deepspace navigation is the NASA Deep Space Network (DSN). High-performance navigation is achieved using Delta Differential One-Way Range techniques that utilize simultaneous observations from multiple DSN sites, and incorporate observations of quasars near the line-of-sight to a spacecraft in order to improve the range and angle measurement accuracies. Over the past four decades, x-ray astronomers have identified a number of xray pulsars with pulsed emissions having stabilities comparable to atomic clocks. The x-ray pulsar-based navigation and time determination (XNAV) system uses phase measurements from these sources to establish autonomously the position of the detector, and thus the spacecraft, relative to a known reference frame, much as the Global Positioning System (GPS) uses phase measurements from radio signals from several satellites to establish the position of the user relative to an Earth-centered fixed frame of reference. While a GPS receiver uses an antenna to detect the radio signals, XNAV uses a detector array to capture the individual xray photons from the x-ray pulsars. The navigation solution relies on detailed xray source models, signal processing, navigation and timing algorithms, and analytical tools that form the basis of an autonomous XNAV system. Through previous XNAV development efforts, some techniques have been established to utilize a pulsar pulse time-of-arrival (TOA) measurement to correct a position estimate. One well-studied approach, based upon Kalman filter methods, optimally adjusts a dynamic orbit propagation solution based upon the offset in measured and predicted pulse TOA. In this delta position estimator scheme, previously estimated values of spacecraft position and velocity are utilized from an onboard orbit propagator. Using these estimated values, the detected arrival times at the spacecraft of pulses from a pulsar are compared to the predicted arrival times defined by the pulsar s pulse timing model. A discrepancy provides an estimate of the spacecraft position offset, since an error in position will relate to the measured time offset of a pulse along the line of sight to the pulsar. XNAV researchers have been developing additional enhanced approaches to process the photon TOAs to arrive at an estimate of spacecraft position, including those using maximum-likelihood estimation, digital phase locked loops, and "single photon processing" schemes that utilize all available time data associated with each photon. Using pulsars from separate, non-coplanar locations provides range and range-rate measurements in each pulsar s direction. Combining these different pulsar measurements solves for offsets in position and velocity in three dimensions, and provides accurate overall navigation for deep space vehicles.

Lateral velocity estimation bias due to beamforming delay errors (Conference Presentation)

NASA Astrophysics Data System (ADS)

Rodriguez-Molares, Alfonso; Fadnes, Solveig; Swillens, Abigail; Løvstakken, Lasse

2017-03-01

An artefact has recently been reported [1,2] in the estimation of the lateral blood velocity using speckle tracking. This artefact shows as a net velocity bias in presence of strong spatial velocity gradients such as those that occur at the edges of the filling jets in the heart. Even though this artifact has been found both in vitro and in simulated data, its causes are still undescribed. Here we demonstrate that a potential source of this artefact can be traced to smaller errors in the beamforming setup. By inserting a small offset in the beamforming delay, one can artificially create a net lateral movement in the speckle in areas of high velocity gradient. That offset does not have a strong impact in the image quality and can easily go undetected.

Exploring the Use of Alfven Waves in Magnetometer Calibration at Geosynchronous Orbit

NASA Technical Reports Server (NTRS)

Bentley, John; Sheppard, David; RIch, Frederick; Redmon, Robert; Loto'aniu, Paul; Chu, Donald

2016-01-01

An Alfven wave is a type magnetohydrodynamicwave that travels through a conducting fluid under the influence of a magnetic field. Researchers have successfully calculated offset vectors of magnetometers in interplanetary space by optimizing the offset to maximize certain Alfvenic properties of observed waves (Leinweber, Belcher). If suitable Alfven waves can be found in the magnetosphere at geosynchronous altitude then these techniques could be used to augment the overall calibration plan for magnetometers in this region such as on the GOES spacecraft, possibly increasing the time between regular maneuvers. Calibration maneuvers may be undesirable because they disrupt the activities of other instruments. Various algorithms to calculate an offset using Alfven waves were considered. A new variation of the Davis-Smith method was derived because it can be mathematically shown that the Davis-Smith method tolerates filtered data, which expands potential applications. The variant developed was designed to find only the offset in the plane normal to the main field because the overall direction of Earth's magnetic field rarely changes, and theory suggests the Alfvenic disturbances occur transverse to the main field. Other variations of the Davis-Smith method encounter problems with data containing waves that propagate in mostly the same direction. A searching algorithm was then designed to look for periods of time with potential Alfven waves in GOES 15 data based on parameters requiring that disturbances be normal to the main field and not change field magnitude. Final waves for calculation were hand-selected. These waves produced credible two-dimensional offset vectors when input to the Davis-Smith method. Multiple two-dimensional solutions in different planes can be combined to get a measurement of the complete offset. The resulting three dimensional offset did not show sufficient precision over several years to be used as a primary calibration method, but reflected changes in the offset fairly well, suggesting that the method could be helpful in monitoring trends of the offset vector when maneuvers cannot be used.

High resolution remote sensing for reducing uncertainties in urban forest carbon offset life cycle assessments.

PubMed

Tigges, Jan; Lakes, Tobia

2017-10-04

Urban forests reduce greenhouse gas emissions by storing and sequestering considerable amounts of carbon. However, few studies have considered the local scale of urban forests to effectively evaluate their potential long-term carbon offset. The lack of precise, consistent and up-to-date forest details is challenging for long-term prognoses. Therefore, this review aims to identify uncertainties in urban forest carbon offset assessment and discuss the extent to which such uncertainties can be reduced by recent progress in high resolution remote sensing. We do this by performing an extensive literature review and a case study combining remote sensing and life cycle assessment of urban forest carbon offset in Berlin, Germany. Recent progress in high resolution remote sensing and methods is adequate for delivering more precise details on the urban tree canopy, individual tree metrics, species, and age structures compared to conventional land use/cover class approaches. These area-wide consistent details can update life cycle inventories for more precise future prognoses. Additional improvements in classification accuracy can be achieved by a higher number of features derived from remote sensing data of increasing resolution, but first studies on this subject indicated that a smart selection of features already provides sufficient data that avoids redundancies and enables more efficient data processing. Our case study from Berlin could use remotely sensed individual tree species as consistent inventory of a life cycle assessment. However, a lack of growth, mortality and planting data forced us to make assumptions, therefore creating uncertainty in the long-term prognoses. Regarding temporal changes and reliable long-term estimates, more attention is required to detect changes of gradual growth, pruning and abrupt changes in tree planting and mortality. As such, precise long-term urban ecological monitoring using high resolution remote sensing should be intensified, especially due to increasing climate change effects. This is important for calibrating and validating recent prognoses of urban forest carbon offset, which have so far scarcely addressed longer timeframes. Additionally, higher resolution remote sensing of urban forest carbon estimates can improve upscaling approaches, which should be extended to reach a more precise global estimate for the first time. Urban forest carbon offset can be made more relevant by making more standardized assessments available for science and professional practitioners, and the increasing availability of high resolution remote sensing data and the progress in data processing allows for precisely that.

Baseline map of organic carbon in Australian soil to support national carbon accounting and monitoring under climate change

PubMed Central

Viscarra Rossel, Raphael A; Webster, Richard; Bui, Elisabeth N; Baldock, Jeff A

2014-01-01

We can effectively monitor soil condition—and develop sound policies to offset the emissions of greenhouse gases—only with accurate data from which to define baselines. Currently, estimates of soil organic C for countries or continents are either unavailable or largely uncertain because they are derived from sparse data, with large gaps over many areas of the Earth. Here, we derive spatially explicit estimates, and their uncertainty, of the distribution and stock of organic C in the soil of Australia. We assembled and harmonized data from several sources to produce the most comprehensive set of data on the current stock of organic C in soil of the continent. Using them, we have produced a fine spatial resolution baseline map of organic C at the continental scale. We describe how we made it by combining the bootstrap, a decision tree with piecewise regression on environmental variables and geostatistical modelling of residuals. Values of stock were predicted at the nodes of a 3-arc-sec (approximately 90 m) grid and mapped together with their uncertainties. We then calculated baselines of soil organic C storage over the whole of Australia, its states and territories, and regions that define bioclimatic zones, vegetation classes and land use. The average amount of organic C in Australian topsoil is estimated to be 29.7 t ha−1 with 95% confidence limits of 22.6 and 37.9 t ha−1. The total stock of organic C in the 0–30 cm layer of soil for the continent is 24.97 Gt with 95% confidence limits of 19.04 and 31.83 Gt. This represents approximately 3.5% of the total stock in the upper 30 cm of soil worldwide. Australia occupies 5.2% of the global land area, so the total organic C stock of Australian soil makes an important contribution to the global carbon cycle, and it provides a significant potential for sequestration. As the most reliable approximation of the stock of organic C in Australian soil in 2010, our estimates have important applications. They could support Australia's National Carbon Accounting System, help guide the formulation of policy around carbon offset schemes, improve Australia's carbon balances, serve to direct future sampling for inventory, guide the design of monitoring networks and provide a benchmark against which to assess the impact of changes in land cover, land management and climate on the stock of C in Australia. In this way, these estimates would help us to develop strategies to adapt and mitigate the effects of climate change. PMID:24599716

Baseline map of organic carbon in Australian soil to support national carbon accounting and monitoring under climate change.

PubMed

Viscarra Rossel, Raphael A; Webster, Richard; Bui, Elisabeth N; Baldock, Jeff A

2014-09-01

We can effectively monitor soil condition-and develop sound policies to offset the emissions of greenhouse gases-only with accurate data from which to define baselines. Currently, estimates of soil organic C for countries or continents are either unavailable or largely uncertain because they are derived from sparse data, with large gaps over many areas of the Earth. Here, we derive spatially explicit estimates, and their uncertainty, of the distribution and stock of organic C in the soil of Australia. We assembled and harmonized data from several sources to produce the most comprehensive set of data on the current stock of organic C in soil of the continent. Using them, we have produced a fine spatial resolution baseline map of organic C at the continental scale. We describe how we made it by combining the bootstrap, a decision tree with piecewise regression on environmental variables and geostatistical modelling of residuals. Values of stock were predicted at the nodes of a 3-arc-sec (approximately 90 m) grid and mapped together with their uncertainties. We then calculated baselines of soil organic C storage over the whole of Australia, its states and territories, and regions that define bioclimatic zones, vegetation classes and land use. The average amount of organic C in Australian topsoil is estimated to be 29.7 t ha(-1) with 95% confidence limits of 22.6 and 37.9 t ha(-1) . The total stock of organic C in the 0-30 cm layer of soil for the continent is 24.97 Gt with 95% confidence limits of 19.04 and 31.83 Gt. This represents approximately 3.5% of the total stock in the upper 30 cm of soil worldwide. Australia occupies 5.2% of the global land area, so the total organic C stock of Australian soil makes an important contribution to the global carbon cycle, and it provides a significant potential for sequestration. As the most reliable approximation of the stock of organic C in Australian soil in 2010, our estimates have important applications. They could support Australia's National Carbon Accounting System, help guide the formulation of policy around carbon offset schemes, improve Australia's carbon balances, serve to direct future sampling for inventory, guide the design of monitoring networks and provide a benchmark against which to assess the impact of changes in land cover, land management and climate on the stock of C in Australia. In this way, these estimates would help us to develop strategies to adapt and mitigate the effects of climate change. © 2014 The Authors. Global Change Biology Published by John Wiley & Sons Ltd.

New Data on Quaternary Surface Offset and Slip Rates of the Oquirrh Fault (Utah, USA) from DSMs made with Structure-from-Motion Methods

NASA Astrophysics Data System (ADS)

Bunds, M. P.; Andreini, J.; Larsen, K.; Fletcher, A.; Arnold, M.; Toke, N. A.

2016-12-01

We generated two high-resolution digital surface models (DSMs) using imagery collected with inexpensive quadcopters and processed with structure-from-motion software to measure offsets of pluvial Lake Bonneville shorelines along the Oquirrh Fault in Utah, USA. The Oquirrh Fault is a west-dipping normal fault that bounds the populous Tooele Valley and is likely contiguous with the East Great Salt Lake Fault to the north and Southern Oquirrh and Topliff Hill Faults to the south, forming a fault system >200 km long, the second longest in Utah. However, knowledge of the fault's parameters is based primarily on one trenching study on the northern section of the fault (Olig et al., 1996). The two DSMs were made using a 24 Mpixel Sony A5100 and 12 Mpixel GoPro camera, have 5 and 10 cm pixels, and span 3.9 km of the fault's trace at the boundary between its central and southern sections. Vertical RMS error of the DSMs relative to bare-ground checkpoints is 5.8 and 9.5 cm for the Sony and GoPro-derived DSMs, respectively. Shoreline features interpreted to have formed < 14,000, 18,000-23,000, and > 23,000 ybp (Godsey et al., 2011; Oviatt, 2015) are offset 2.8-3.0, 5.6-6.7, and 8.1-9.3 m, respectively. From these offsets we infer three surface-rupturing earthquakes with displacements of 2.8-3.0, 2.6-3.8, and 1.3-3.8 m, and estimate the slip rate to be 0.24 - 0.37 mm/yr. These results are consistent with those of the prior study to the north, suggesting co-rupturing of the northern, central and northernmost part of the southern section of the fault. In addition, the inferred large single event displacements suggest even longer surface ruptures. We have used the same methods to construct 5 cm pixel DSMs up to 4.4 km2 in area to support several additional paleoseismological, paleotsunami, and neotectonic investigations, which highlights the many benefits to geoscience research of the capacity to quickly produce accurate, high resolution DSMs from inexpensive equipment.

Adaptive offset correction for intracortical brain-computer interfaces.

PubMed

Homer, Mark L; Perge, Janos A; Black, Michael J; Harrison, Matthew T; Cash, Sydney S; Hochberg, Leigh R

2014-03-01

Intracortical brain-computer interfaces (iBCIs) decode intended movement from neural activity for the control of external devices such as a robotic arm. Standard approaches include a calibration phase to estimate decoding parameters. During iBCI operation, the statistical properties of the neural activity can depart from those observed during calibration, sometimes hindering a user's ability to control the iBCI. To address this problem, we adaptively correct the offset terms within a Kalman filter decoder via penalized maximum likelihood estimation. The approach can handle rapid shifts in neural signal behavior (on the order of seconds) and requires no knowledge of the intended movement. The algorithm, called multiple offset correction algorithm (MOCA), was tested using simulated neural activity and evaluated retrospectively using data collected from two people with tetraplegia operating an iBCI. In 19 clinical research test cases, where a nonadaptive Kalman filter yielded relatively high decoding errors, MOCA significantly reduced these errors ( 10.6 ± 10.1% ; p < 0.05, pairwise t-test). MOCA did not significantly change the error in the remaining 23 cases where a nonadaptive Kalman filter already performed well. These results suggest that MOCA provides more robust decoding than the standard Kalman filter for iBCIs.

A comparison of mapped and measured total ionospheric electron content using global positioning system and beacon satellite observations

NASA Technical Reports Server (NTRS)

Lanyi, Gabor E.; Roth, Titus

1988-01-01

Total ionospheric electron contents (TEC) were measured by global positioning system (GPS) dual-frequency receivers developed by the Jet Propulsion Laboratory. The measurements included P-code (precise ranging code) and carrier phase data for six GPS satellites during multiple five-hour observing sessions. A set of these GPS TEC measurements were mapped from the GPS lines of sight to the line of sight of a Faraday beacon satellite by statistically fitting the TEC data to a simple model of the ionosphere. The mapped GPS TEC values were compared with the Faraday rotation measurements. Because GPS transmitter offsets are different for each satellite and because some GPS receiver offsets were uncalibrated, the sums of the satellite and receiver offsets were estimated simultaneously with the TEC in a least squares procedure. The accuracy of this estimation procedure is evaluated indicating that the error of the GPS-determined line of sight TEC can be at or below 1 x 10 to the 16th el/sq cm. Consequently, the current level of accuracy is comparable to the Faraday rotation technique; however, GPS provides superior sky coverage.

Evaluation of machine learning tools for inspection of steam generator tube structures using pulsed eddy current

NASA Astrophysics Data System (ADS)

Buck, J. A.; Underhill, P. R.; Morelli, J.; Krause, T. W.

2017-02-01

Degradation of nuclear steam generator (SG) tubes and support structures can result in a loss of reactor efficiency. Regular in-service inspection, by conventional eddy current testing (ECT), permits detection of cracks, measurement of wall loss, and identification of other SG tube degradation modes. However, ECT is challenged by overlapping degradation modes such as might occur for SG tube fretting accompanied by tube off-set within a corroding ferromagnetic support structure. Pulsed eddy current (PEC) is an emerging technology examined here for inspection of Alloy-800 SG tubes and associated carbon steel drilled support structures. Support structure hole size was varied to simulate uniform corrosion, while SG tube was off-set relative to hole axis. PEC measurements were performed using a single driver with an 8 pick-up coil configuration in the presence of flat-bottom rectangular frets as an overlapping degradation mode. A modified principal component analysis (MPCA) was performed on the time-voltage data in order to reduce data dimensionality. The MPCA scores were then used to train a support vector machine (SVM) that simultaneously targeted four independent parameters associated with; support structure hole size, tube off-centering in two dimensions and fret depth. The support vector machine was trained, tested, and validated on experimental data. Results were compared with a previously developed artificial neural network (ANN) trained on the same data. Estimates of tube position showed comparable results between the two machine learning tools. However, the ANN produced better estimates of hole inner diameter and fret depth. The better results from ANN analysis was attributed to challenges associated with the SVM when non-constant variance is present in the data.

Bowhead whale localization using time-difference-of-arrival data from asynchronous recorders.

PubMed

Warner, Graham A; Dosso, Stan E; Hannay, David E

2017-03-01

This paper estimates bowhead whale locations and uncertainties using nonlinear Bayesian inversion of the time-difference-of-arrival (TDOA) of low-frequency whale calls recorded on onmi-directional asynchronous recorders in the shallow waters of the northeastern Chukchi Sea, Alaska. A Y-shaped cluster of seven autonomous ocean-bottom hydrophones, separated by 0.5-9.2 km, was deployed for several months over which time their clocks drifted out of synchronization. Hundreds of recorded whale calls are manually associated between recorders. The TDOA between hydrophone pairs are calculated from filtered waveform cross correlations and depend on the whale locations, hydrophone locations, relative recorder clock offsets, and effective waveguide sound speed. A nonlinear Bayesian inversion estimates all of these parameters and their uncertainties as well as data error statistics. The problem is highly nonlinear and a linearized inversion did not produce physically realistic results. Whale location uncertainties from nonlinear inversion can be low enough to allow accurate tracking of migrating whales that vocalize repeatedly over several minutes. Estimates of clock drift rates are obtained from inversions of TDOA data over two weeks and agree with corresponding estimates obtained from long-time averaged ambient noise cross correlations. The inversion is suitable for application to large data sets of manually or automatically detected whale calls.

Estimating the Societal Benefits of THA After Accounting for Work Status and Productivity: A Markov Model Approach.

PubMed

Koenig, Lane; Zhang, Qian; Austin, Matthew S; Demiralp, Berna; Fehring, Thomas K; Feng, Chaoling; Mather, Richard C; Nguyen, Jennifer T; Saavoss, Asha; Springer, Bryan D; Yates, Adolph J

2016-12-01

Demand for total hip arthroplasty (THA) is high and expected to continue to grow during the next decade. Although much of this growth includes working-aged patients, cost-effectiveness studies on THA have not fully incorporated the productivity effects from surgery. We asked: (1) What is the expected effect of THA on patients' employment and earnings? (2) How does accounting for these effects influence the cost-effectiveness of THA relative to nonsurgical treatment? Taking a societal perspective, we used a Markov model to assess the overall cost-effectiveness of THA compared with nonsurgical treatment. We estimated direct medical costs using Medicare claims data and indirect costs (employment status and worker earnings) using regression models and nonparametric simulations. For direct costs, we estimated average spending 1 year before and after surgery. Spending estimates included physician and related services, hospital inpatient and outpatient care, and postacute care. For indirect costs, we estimated the relationship between functional status and productivity, using data from the National Health Interview Survey and regression analysis. Using regression coefficients and patient survey data, we ran a nonparametric simulation to estimate productivity (probability of working multiplied by earnings if working minus the value of missed work days) before and after THA. We used the Australian Orthopaedic Association National Joint Replacement Registry to obtain revision rates because it contained osteoarthritis-specific THA revision rates by age and gender, which were unavailable in other registry reports. Other model assumptions were extracted from a previously published cost-effectiveness analysis that included a comprehensive literature review. We incorporated all parameter estimates into Markov models to assess THA effects on quality-adjusted life years and lifetime costs. We conducted threshold and sensitivity analyses on direct costs, indirect costs, and revision rates to assess the robustness of our Markov model results. Compared with nonsurgical treatments, THA increased average annual productivity of patients by USD 9503 (95% CI, USD 1446-USD 17,812). We found that THA increases average lifetime direct costs by USD 30,365, which were offset by USD 63,314 in lifetime savings from increased productivity. With net societal savings of USD 32,948 per patient, total lifetime societal savings were estimated at almost USD 10 billion from more than 300,000 THAs performed in the United States each year. Using a Markov model approach, we show that THA produces societal benefits that can offset the costs of THA. When comparing THA with other nonsurgical treatments, policymakers should consider the long-term benefits associated with increased productivity from surgery. Level III, economic and decision analysis.

Simple Adaptive Single Differential Coherence Detection of BPSK Signals in IEEE 802.15.4 Wireless Sensor Networks

PubMed Central

Wen, Hong; Wang, Longye; Xie, Ping; Song, Liang; Tang, Jie; Liao, Runfa

2017-01-01

In this paper, we propose an adaptive single differential coherent detection (SDCD) scheme for the binary phase shift keying (BPSK) signals in IEEE 802.15.4 Wireless Sensor Networks (WSNs). In particular, the residual carrier frequency offset effect (CFOE) for differential detection is adaptively estimated, with only linear operation, according to the changing channel conditions. It was found that the carrier frequency offset (CFO) and chip signal-to-noise ratio (SNR) conditions do not need a priori knowledge. This partly benefits from that the combination of the trigonometric approximation sin−1(x)≈x and a useful assumption, namely, the asymptotic or high chip SNR, is considered for simplification of the full estimation scheme. Simulation results demonstrate that the proposed algorithm can achieve an accurate estimation and the detection performance can completely meet the requirement of the IEEE 802.15.4 standard, although with a little loss of reliability and robustness as compared with the conventional optimal single-symbol detector. PMID:29278404

Simple Adaptive Single Differential Coherence Detection of BPSK Signals in IEEE 802.15.4 Wireless Sensor Networks.

PubMed

Zhang, Gaoyuan; Wen, Hong; Wang, Longye; Xie, Ping; Song, Liang; Tang, Jie; Liao, Runfa

2017-12-26

In this paper, we propose an adaptive single differential coherent detection (SDCD) scheme for the binary phase shift keying (BPSK) signals in IEEE 802.15.4 Wireless Sensor Networks (WSNs). In particular, the residual carrier frequency offset effect (CFOE) for differential detection is adaptively estimated, with only linear operation, according to the changing channel conditions. It was found that the carrier frequency offset (CFO) and chip signal-to-noise ratio (SNR) conditions do not need a priori knowledge. This partly benefits from that the combination of the trigonometric approximation sin - 1 ( x ) ≈ x and a useful assumption, namely, the asymptotic or high chip SNR, is considered for simplification of the full estimation scheme. Simulation results demonstrate that the proposed algorithm can achieve an accurate estimation and the detection performance can completely meet the requirement of the IEEE 802.15.4 standard, although with a little loss of reliability and robustness as compared with the conventional optimal single-symbol detector.

A new stylolite classification scheme to estimate compaction and local permeability variations

NASA Astrophysics Data System (ADS)

Koehn, D.; Rood, M. P.; Beaudoin, N.; Chung, P.; Bons, P. D.; Gomez-Rivas, E.

2016-12-01

We modeled the geometrical roughening of bedding-parallel, mainly layer-dominated stylolites in order to understand their structural evolution, to present an advanced classification of stylolite shapes and to relate this classification to chemical compaction and permeability variations at stylolites. Stylolites are rough dissolution seams that develop in sedimentary basins during chemical compaction. In the Zechstein 2 carbonate units, an important lean gas reservoir in the southern Permian Zechstein basin in Germany, stylolites influence local fluid flow, mineral replacement reactions and hence the permeability of the reservoir. Our simulations demonstrate that layer-dominated stylolites can grow in three distinct stages: an initial slow nucleation phase, a fast layer-pinning phase and a final freezing phase if the layer is completely dissolved during growth. Dissolution of the pinning layer and thus destruction of the stylolite's compaction tracking capabilities is a function of the background noise in the rock and the dissolution rate of the layer itself. Low background noise needs a slower dissolving layer for pinning to be successful but produces flatter teeth than higher background noise. We present an advanced classification based on our simulations and separate stylolites into four classes: (1) rectangular layer type, (2) seismogram pinning type, (3) suture/sharp peak type and (4) simple wave-like type. Rectangular layer type stylolites are the most appropriate for chemical compaction estimates because they grow linearly and record most of the actual compaction (up to 40 mm in the Zechstein example). Seismogram pinning type stylolites also provide good tracking capabilities, with the largest teeth tracking most of the compaction. Suture/sharp peak type stylolites grow in a non-linear fashion and thus do not record most of the actual compaction. However, when a non-linear growth law is used, the compaction estimates are similar to those making use of the rectangular layer type stylolites. Simple wave-like stylolites are not useful for compaction estimates, since their growth is highly non-linear with a very low growth exponent. In the case where sealing material is collected at the tooth during dissolution, stylolites can act as barriers for local fluid flow as they intensify sealing capabilities of pinning layers. However, the development of teeth and spikes offsets and thus destroys continuous stylolite seams so that the permeability across the stylolite becomes very heterogeneous and they are no continuous barriers. This behavior is best shown in rectangular layer and seismogram pinning type stylolites that develop efficient fluid barriers at teeth tips but destroy sealing capabilities of layers by offsetting them at the flank, leading to a permeability anisotropy along 2-D stylolite planes. Suture/sharp peak stylolites can create fluid barriers if they collect enough sealing material. However, if the collecting material does not seal or if spikes offset the sealing material the stylolite leaks. We propose that our classification can be used to realistically estimate chemical compaction in reservoirs and gives an indication on how heterogeneous the permeability of stylolites can be.

The Coronal-Dimming Footprint of a Streamer-Puff Coronal Mass Ejection: Confirmation of the Magnetic-Arch-Blowout Scenario

NASA Technical Reports Server (NTRS)

Moore, Ronald L.; Sterling, Alphonse C.

2007-01-01

In this paper, for a CME of the particular variety recently identified by Bemporad et al (2005), we present new evidence that strengthens the conclusion of Bemporad et al that for these CMEs the pre-eruption magnetic field that explodes to drive the CME is laterally far offset from the radial path of the full-blown CME in the outer corona. In CMEs of the particular variety of those found by Bemporad et al, the flare-site field that explodes is much more compact than the flare-site fields that explode in most major flares and large CMEs, and is located in a flank of the base of a streamer. After presenting our new evidence for how CMEs of this variety are produced, we cite and discuss examples of larger flare-producing magnetic explosions that are not necessarily in a flank of a streamer but occur together with a large CME that in the outer corona is laterally far offset from the flare. We conclude that there is a broad class of CMEs that come from flare-producing magnetic explosions of various sizes and that are laterally far offset from the flare. We propose that all CMEs of this broad class are produced in basically the same way as those of the particular variety of the one that we present in this paper. In this paper, it is therefore convenient and useful to refer to this broad class of CMEs (regardless of the pre-eruption size of the offset field that explodes and whether or not this field is in the flank of a streamer), as "over-and-out" CMEs. Because the lack of recognition of this class of CMEs has contributed to the confusion and controversy regarding the relation between flares and CMEs (e.g., Kahler 1992; Gosling 1993; Hudson et al 1995), it is important that this class of CME have an explicit name. We adopt the name over-and-out CME because it is a needed descriptive term, especially for the purpose of this paper.

Determination of Flux-Gate Magnetometer Spin Axis Offsets with the Electron Drift Instrument

NASA Astrophysics Data System (ADS)

Plaschke, Ferdinand; Nakamura, Rumi; Giner, Lukas; Teubenbacher, Robert; Chutter, Mark; Leinweber, Hannes K.; Magnes, Werner

2014-05-01

Spin-stabilization of spacecraft enormously supports the in-flight calibration of onboard flux-gate magnetometers (FGMs): eight out of twelve calibration parameters can be determined by minimization of spin tone and harmonics in the calibrated magnetic field measurements. From the remaining four parameters, the spin axis offset is usually obtained by analyzing observations of Alfvénic fluctuations in the solar wind. If solar wind measurements are unavailable, other methods for spin axis offset determination need to be used. We present two alternative methods that are based on the comparison of FGM and electron drift instrument (EDI) data: (1) EDI measures the gyration periods of instrument-emitted electrons in the ambient magnetic field. They are inversely proportional to the magnetic field strength. Differences between FGM and EDI measured field strengths can be attributed to inaccuracies in spin axis offset, if the other calibration parameters are accurately known. (2) For EDI electrons to return to the spacecraft, they have to be sent out in perpendicular direction to the ambient magnetic field. Minimization of the variance of electron beam directions with respect to the FGM-determined magnetic field direction also yields an estimate of the spin axis offset. Prior to spin axis offset determination, systematic inaccuracies in EDI gyration period measurements and in the transformation of EDI beam directions into the FGM spin-aligned reference coordinate system have to be corrected. We show how this can be done by FGM/EDI data comparison, as well.

Inter-instrument calibration using magnetic field data from Flux Gate Magnetometer (FGM) and Electron Drift Instrument (EDI) onboard Cluster

NASA Astrophysics Data System (ADS)

Nakamura, R.; Plaschke, F.; Teubenbacher, R.; Giner, L.; Baumjohann, W.; Magnes, W.; Steller, M.; Torbert, R. B.; Vaith, H.; Chutter, M.; Fornaçon, K.-H.; Glassmeier, K.-H.; Carr, C.

2013-07-01

We compare the magnetic field data obtained from the Flux-Gate Magnetometer (FGM) and the magnetic field data deduced from the gyration time of electrons measured by the Electron Drift Instrument (EDI) onboard Cluster to determine the spin axis offset of the FGM measurements. Data are used from orbits with their apogees in the magnetotail, when the magnetic field magnitude was between about 20 nT and 500 nT. Offset determination with the EDI-FGM comparison method is of particular interest for these orbits, because no data from solar wind are available in such orbits to apply the usual calibration methods using the Alfvén waves. In this paper, we examine the effects of the different measurement conditions, such as direction of the magnetic field relative to the spin plane and field magnitude in determining the FGM spin-axis offset, and also take into account the time-of-flight offset of the EDI measurements. It is shown that the method works best when the magnetic field magnitude is less than about 128 nT and when the magnetic field is aligned near the spin-axis direction. A remaining spin-axis offset of about 0.4 ~ 0.6 nT was observed between July and October 2003. Using multi-point multi-instrument measurements by Cluster we further demonstrate the importance of the accurate determination of the spin-axis offset when estimating the magnetic field gradient.

Interinstrument calibration using magnetic field data from the flux-gate magnetometer (FGM) and electron drift instrument (EDI) onboard Cluster

NASA Astrophysics Data System (ADS)

Nakamura, R.; Plaschke, F.; Teubenbacher, R.; Giner, L.; Baumjohann, W.; Magnes, W.; Steller, M.; Torbert, R. B.; Vaith, H.; Chutter, M.; Fornaçon, K.-H.; Glassmeier, K.-H.; Carr, C.

2014-01-01

We compare the magnetic field data obtained from the flux-gate magnetometer (FGM) and the magnetic field data deduced from the gyration time of electrons measured by the electron drift instrument (EDI) onboard Cluster to determine the spin-axis offset of the FGM measurements. Data are used from orbits with their apogees in the magnetotail, when the magnetic field magnitude was between about 20 and 500 nT. Offset determination with the EDI-FGM comparison method is of particular interest for these orbits, because no data from solar wind are available in such orbits to apply the usual calibration methods using the Alfvén waves. In this paper, we examine the effects of the different measurement conditions, such as direction of the magnetic field relative to the spin plane and field magnitude in determining the FGM spin-axis offset, and also take into account the time-of-flight offset of the EDI measurements. It is shown that the method works best when the magnetic field magnitude is less than about 128 nT and when the magnetic field is aligned near the spin-axis direction. A remaining spin-axis offset of about 0.4 ∼ 0.6 nT was observed for Cluster 1 between July and October 2003. Using multipoint multi-instrument measurements by Cluster we further demonstrate the importance of the accurate determination of the spin-axis offset when estimating the magnetic field gradient.

Gamma-Ray Pulsar Light Curves in Offset Polar Cap Geometry

NASA Technical Reports Server (NTRS)

Harding, Alice K.; DeCesar, Megan; Miller, M. Coleman

2011-01-01

Recent studies have shown that gamma-ray pulsar light curves are very sensitive to the geometry of the pulsar magnetic field. Pulsar magnetic field geometries, such as the retarded vacuum dipole and force-free magnetospheres, used to model high-energy light curves have distorted polar caps that are offset from the magnetic axis in the direction opposite to rotation. Since this effect is due to the sweepback of field lines near the light cylinder, offset polar caps are a generic property of pulsar magnetospheres and their effects should be included in gamma-ray pulsar light curve modeling. In slot gap models (having two-pole caustic geometry), the offset polar caps cause a strong azimuthal asymmetry of the particle acceleration around the magnetic axis. We have studied the effect of the offset polar caps in both retarded vacuum dipole and force-free geometry on the model high-energy pulse profile. We find that. corn pared to the profile:-; derived from :-;ymmetric caps, the flux in the pulse peaks, which are caustics formed along the trailing magnetic field lines. increases significantly relative to the off-peak emission. formed along leading field lines. The enhanced contrast produces greatly improved slot gap model fits to Fermi pulsar light curves like Vela, which show very little off-peak emIssIon.

The effect of offset cues on saccade programming and covert attention.

PubMed

Smith, Daniel T; Casteau, Soazig

2018-02-01

Salient peripheral events trigger fast, "exogenous" covert orienting. The influential premotor theory of attention argues that covert orienting of attention depends upon planned but unexecuted eye-movements. One problem with this theory is that salient peripheral events, such as offsets, appear to summon attention when used to measure covert attention (e.g., the Posner cueing task) but appear not to elicit oculomotor preparation in tasks that require overt orienting (e.g., the remote distractor paradigm). Here, we examined the effects of peripheral offsets on covert attention and saccade preparation. Experiment 1 suggested that transient offsets summoned attention in a manual detection task without triggering motor preparation planning in a saccadic localisation task, although there were a high proportion of saccadic capture errors on "no-target" trials, where a cue was presented but no target appeared. In Experiment 2, "no-target" trials were removed. Here, transient offsets produced both attentional facilitation and faster saccadic responses on valid cue trials. A third experiment showed that the permanent disappearance of an object also elicited attentional facilitation and faster saccadic reaction times. These experiments demonstrate that offsets trigger both saccade programming and covert attentional orienting, consistent with the idea that exogenous, covert orienting is tightly coupled with oculomotor activation. The finding that no-go trials attenuates oculomotor priming effects offers a way to reconcile the current findings with previous claims of a dissociation between covert attention and oculomotor control in paradigms that utilise a high proportion of catch trials.

Galaxy Zoo: finding offset discs and bars in SDSS galaxies★

NASA Astrophysics Data System (ADS)

Kruk, Sandor J.; Lintott, Chris J.; Simmons, Brooke D.; Bamford, Steven P.; Cardamone, Carolin N.; Fortson, Lucy; Hart, Ross E.; Häußler, Boris; Masters, Karen L.; Nichol, Robert C.; Schawinski, Kevin; Smethurst, Rebecca J.

2017-08-01

We use multiwavelength Sloan Digital Sky Survey (SDSS) images and Galaxy Zoo morphologies to identify a sample of ˜270 late-type galaxies with an off-centre bar. We measure offsets in the range 0.2-2.5 kpc between the photometric centres of the stellar disc and stellar bar. The measured offsets correlate with global asymmetries of the galaxies, with those with largest offsets showing higher lopsidedness. These findings are in good agreement with predictions from simulations of dwarf-dwarf tidal interactions producing off-centre bars. We find that the majority of galaxies with off-centre bars are of Magellanic type, with a median mass of 109.6 M⊙, and 91 per cent of them having M⋆ < 3 × 1010 M⊙, the characteristic mass at which galaxies start having higher central concentrations attributed to the presence of bulges. We conduct a search for companions to test the hypothesis of tidal interactions, but find that a similar fraction of galaxies with offset bars have companions within 100 kpc as galaxies with centred bars. Although this may be due to the incompleteness of the SDSS spectroscopic survey at the faint end, alternative scenarios that give rise to offset bars such as interactions with dark companions or the effect of lopsided halo potentials should be considered. Future observations are needed to confirm possible low-mass companion candidates and to determine the shape of the dark matter halo, in order to find the explanation for the off-centre bars in these galaxies.

Methods of Measurement the Quality Metrics in a Printing System

NASA Astrophysics Data System (ADS)

Varepo, L. G.; Brazhnikov, A. Yu; Nagornova, I. V.; Novoselskaya, O. A.

2018-04-01

One of the main criteria for choosing ink as a component of printing system is scumming ability of the ink. The realization of algorithm for estimating the quality metrics in a printing system is shown. The histograms of ink rate of various printing systems are presented. A quantitative estimation of stability of offset inks emulsifiability is given.

Forest disturbance and North American carbon flux

Treesearch

S. N. Goward; J. G. Masek; W. Cohen; G. Moisen; G. J. Collatz; S. Healey; R. A. Houghton; C. Huang; R. Kennedy; B. Law; S. Powell; D. Turner; M. A. Wulder

2008-01-01

North America's forests are thought to be a significant sink for atmospheric carbon. Currently, the rate of sequestration by forests on the continent has been estimated at 0.23 petagrams of carbon per year, though the uncertainty about this estimate is nearly 50%. This offsets about 13% of the fossil fuel emissions from the continent [Pacala et al., 2007]. However...

A strategy to minimize the energy offset in carrier injection from excited dyes to inorganic semiconductors for efficient dye-sensitized solar energy conversion.

PubMed

Fujisawa, Jun-Ichi; Osawa, Ayumi; Hanaya, Minoru

2016-08-10

Photoinduced carrier injection from dyes to inorganic semiconductors is a crucial process in various dye-sensitized solar energy conversions such as photovoltaics and photocatalysis. It has been reported that an energy offset larger than 0.2-0.3 eV (threshold value) is required for efficient electron injection from excited dyes to metal-oxide semiconductors such as titanium dioxide (TiO2). Because the energy offset directly causes loss in the potential of injected electrons, it is a crucial issue to minimize the energy offset for efficient solar energy conversions. However, a fundamental understanding of the energy offset, especially the threshold value, has not been obtained yet. In this paper, we report the origin of the threshold value of the energy offset, solving the long-standing questions of why such a large energy offset is necessary for the electron injection and which factors govern the threshold value, and suggest a strategy to minimize the threshold value. The threshold value is determined by the sum of two reorganization energies in one-electron reduction of semiconductors and typically-used donor-acceptor (D-A) dyes. In fact, the estimated values (0.21-0.31 eV) for several D-A dyes are in good agreement with the threshold value, supporting our conclusion. In addition, our results reveal that the threshold value is possible to be reduced by enlarging the π-conjugated system of the acceptor moiety in dyes and enhancing its structural rigidity. Furthermore, we extend the analysis to hole injection from excited dyes to semiconductors. In this case, the threshold value is given by the sum of two reorganization energies in one-electron oxidation of semiconductors and D-A dyes.

Network global navigation satellite system surveys to harmonize American and Canadian datum for the Lake Champlain Basin

USGS Publications Warehouse

Flynn, Robert H.; Rydlund, Jr., Paul H.; Martin, Daniel J.

2016-03-08

Lake-gage water-surface elevations determined during the 3 days of surveys were converted to water-surface elevations referenced to the North American Vertical Datum of 1988 by using calculated offsets and historical water-surface elevations. In this report, an “offset” refers to the adjustment that needs to be applied to published data from a particular gage to produce elevation data referenced to the North American Vertical Datum of 1988. Offsets presented in this report can be used in the evaluation of water-surface elevations in a common datum for Lake Champlain and the Richelieu River. In addition, the water-level data referenced to the common datum (as determined from the offsets) may be used to calibrate flow models and support future modeling studies developed for Lake Champlain and the Richelieu River.

The Stability Of Disk Barred Galaxies Over the Past 7 Billion Years

NASA Astrophysics Data System (ADS)

Tapia, Amauri; Simmons, Brooke

2017-01-01

A recently released model of interacting disk galaxies provides a hypothesis for the origins of off center bars in disks. No systematic search for offset bars in the early universe has yet been undertaken. The Galaxy Zoo project has produced data regarding the large-scale bars of many galaxies. Using this data alongside images collected by the Hubble Space Telescope and other sources, we have examined 5190 galaxies for signatures of off-centered bars. Less than 5 percent of the sample shows clear signs of an offset bar. We describe their overall properties of this sub-sample and compare the properties of galaxies with offset bars to those with centered bars. We assess the feasibility of the proposed model and place these galaxies in the context of the overall evolution of galaxies.

Coda-wave and ambient noise interferometry using an offset vertical array at Iwanuma site, northeast Japan

NASA Astrophysics Data System (ADS)

Minami, K.; Yamamoto, M.; Nishimura, T.; Nakahara, H.; Shiomi, K.

2013-12-01

Seismic interferometry using vertical borehole arrays is a powerful tool to estimate the shallow subsurface structure and its time lapse changes. However, the wave fields surrounding borehole arrays are non-isotropic due to the existence of ground surface and non-uniform distribution of sources, and do not meet the requirements of the seismic interferometry in a strict sense. In this study, to examine differences between wave fields of coda waves and ambient noise, and to estimate their effects on the results of seismic interferometry, we conducted a temporal seismic experiment using zero-offset and offset vertical arrays. We installed two 3-components seismometers (hereafter called Surface1 and Surface2) at the ground surface in the vicinity of NIED Iwanuma site (Miyagi Pref., Japan). Surface1 is placed just above the Hi-net downhole seismometer whose depth is 101 m, and Surface2 is placed 70 m away from Surface1. To extract the wave propagation between these 3 seismometers, we compute the cross-correlation functions (CCFs) of coda-wave and ambient noise for each pair of the zero-offset vertical (Hi-net-Surface1), finite-offset vertical (Hi-net-Surface2), and horizontal (Surface1-Surface2) arrays. We use the frequency bands of 4-8, 8-16 Hz in the CCF computation. The characteristics of obtained CCFs are summarized as follows; (1) in all frequency bands, the peak lag times of CCFs from coda waves are almost the same between the vertical and offset-vertical arrays irrespective of different inter-station distance, and those for the horizontal array are around 0 s. (2) the peak lag times of CCFs from ambient noise show slight differences, that is, those obtained from the vertical array are earlier than those from the offset-vertical array, and those from the horizontal array are around 0.05 s. (3) the peak lag times of CCFs for the vertical array obtained from ambient noise analyses are earlier than those from the coda-wave analyses. These results indicate that wave fields of coda-wave are mainly composed of vertically propagating waves, while those of ambient noise are composed of both vertically and horizontally propagating waves. To explain these characteristics of the CCFs obtained from different wave fields, we conducted a numerical simulation of interferometry based on the concept of stationary phase. Here, we assume isotropic upward incidence of SV-wave into a homogeneous half-space, and compute CCFs for the zero-offset and finite-offset vertical arrays by taking into account the reflection and conversion of P-SV waves at the free surface. Due to the effectively non-isotropic wave field, the simulated CCF for the zero-offset vertical array shows slight delay in peak lag time and its amplitudes decrease in the acausal part. On the other hand, the simulated CCF for finite-offset vertical array shows amplitude decrease and no peak lag time shift. These results are consistent with the difference in peak lag times obtained from coda-wave and ambient noise analyses. Our observations and theoretical consideration suggest that the careful consideration of wave fields is important in the application of seismic interferometry to borehole array data.

Impacts of GNSS position offsets on global frame stability

NASA Astrophysics Data System (ADS)

Griffiths, Jake; Ray, Jim

2015-04-01

Positional offsets appear in Global Navigation Satellite System (GNSS) time series for a variety of reasons. Antenna or radome changes are the most common cause for these discontinuities. Many others are from earthquakes, receiver changes, and different anthropogenic modifications at or near the stations. Some jumps appear for unknown or undocumented reasons. Accurate determination of station velocities, and therefore geophysical parameters and terrestrial reference frames, requires that positional offsets be correctly found and compensated. Williams (2003) found that undetected offsets introduce a random walk error component in individual station time series. The topic of detecting positional offsets has received considerable attention in recent years (e.g., Detection of Offsets in GPS Experiment; DOGEx), and most research groups using GNSS have adopted a mix of manual and automated methods for finding them. The removal of a positional offset from a time series is usually handled by estimating the average station position on both sides of the discontinuity. Except for large earthquake events, the velocity is usually assumed constant and continuous across the positional jump. This approach is sufficient in the absence of time-correlated errors. However, GNSS time series contain periodic and power-law (flicker) errors. In this paper, we evaluate the impact to individual station results and the overall stability of the global reference frame from adding increasing numbers of positional discontinuities. We use the International GNSS Service (IGS) weekly SINEX files, and iteratively insert positional offset parameters. Each iteration includes a restacking of the modified SINEX files using the CATREF software from Institut National de l'Information Géographique et Forestière (IGN). Comparisons of successive stacked solutions are used to assess the impacts on the time series of x-pole and y-pole offsets, along with changes in regularized position and secular velocity for stations with more than 2.5 years of data. Our preliminary results indicate that the change in polar motion scatter is logarithmic with increasing numbers of discontinuities. The best-fit natural logarithm to the changes in scatter for x-pole has R2 = 0.58; the fit for the y-pole series has R2 = 0.99. From these empirical functions, we find that polar motion scatter increases from zero when the total rate of discontinuities exceeds 0.2 (x-pole) and 1.3 (y-pole) per station, on average (the IGS has 0.65 per station). Thus, the presence of position offsets in GNSS station time series is likely already a contributor to IGS polar motion inaccuracy and global frame instability. Impacts to station position and velocity estimates depend on noise features found in that station's positional time series. For instance, larger changes in velocity occur for stations with shorter and noisier data spans. This is because an added discontinuity parameter for an individual station time series can induce changes in average position on both sides of the break. We will expand on these results, and consider remaining questions about the role of velocity discontinuities and the effects caused by non-core reference frame stations.

Efficient Round-Trip Time Optimization for Replica-Exchange Enveloping Distribution Sampling (RE-EDS).

PubMed

Sidler, Dominik; Cristòfol-Clough, Michael; Riniker, Sereina

2017-06-13

Replica-exchange enveloping distribution sampling (RE-EDS) allows the efficient estimation of free-energy differences between multiple end-states from a single molecular dynamics (MD) simulation. In EDS, a reference state is sampled, which can be tuned by two types of parameters, i.e., smoothness parameters(s) and energy offsets, such that all end-states are sufficiently sampled. However, the choice of these parameters is not trivial. Replica exchange (RE) or parallel tempering is a widely applied technique to enhance sampling. By combining EDS with the RE technique, the parameter choice problem could be simplified and the challenge shifted toward an optimal distribution of the replicas in the smoothness-parameter space. The choice of a certain replica distribution can alter the sampling efficiency significantly. In this work, global round-trip time optimization (GRTO) algorithms are tested for the use in RE-EDS simulations. In addition, a local round-trip time optimization (LRTO) algorithm is proposed for systems with slowly adapting environments, where a reliable estimate for the round-trip time is challenging to obtain. The optimization algorithms were applied to RE-EDS simulations of a system of nine small-molecule inhibitors of phenylethanolamine N-methyltransferase (PNMT). The energy offsets were determined using our recently proposed parallel energy-offset (PEOE) estimation scheme. While the multistate GRTO algorithm yielded the best replica distribution for the ligands in water, the multistate LRTO algorithm was found to be the method of choice for the ligands in complex with PNMT. With this, the 36 alchemical free-energy differences between the nine ligands were calculated successfully from a single RE-EDS simulation 10 ns in length. Thus, RE-EDS presents an efficient method for the estimation of relative binding free energies.

Surface acoustic wave coding for orthogonal frequency coded devices

NASA Technical Reports Server (NTRS)

Malocha, Donald (Inventor); Kozlovski, Nikolai (Inventor)

2011-01-01

Methods and systems for coding SAW OFC devices to mitigate code collisions in a wireless multi-tag system. Each device producing plural stepped frequencies as an OFC signal with a chip offset delay to increase code diversity. A method for assigning a different OCF to each device includes using a matrix based on the number of OFCs needed and the number chips per code, populating each matrix cell with OFC chip, and assigning the codes from the matrix to the devices. The asynchronous passive multi-tag system includes plural surface acoustic wave devices each producing a different OFC signal having the same number of chips and including a chip offset time delay, an algorithm for assigning OFCs to each device, and a transceiver to transmit an interrogation signal and receive OFC signals in response with minimal code collisions during transmission.

Measurement of Separate Cosmic-Ray Electron and Positron Spectra with the Fermi Large Area Telescope

DOE PAGES

Ackermann, M.

2012-01-05

We measured separate cosmic-ray electron and positron spectra with the Fermi Large Area Telescope. Because the instrument does not have an onboard magnet, we distinguish the two species by exploiting the Earth’s shadow, which is offset in opposite directions for opposite charges due to the Earth’s magnetic field. We estimate and subtract the cosmic-ray proton background using two different methods that produce consistent results. We report the electron-only spectrum, the positron-only spectrum, and the positron fraction between 20 GeV and 200 GeV. We confirm that the fraction rises with energy in the 20–100 GeV range. The three new spectral pointsmore » between 100 and 200 GeV are consistent with a fraction that is continuing to rise with energy.« less

Multi-channel Ice Penetrating Radar Traverse for Estimates of Firn Density in the Percolation Zone, Western Greenland Ice Sheet

NASA Astrophysics Data System (ADS)

Meehan, T.; Osterberg, E. C.; Lewis, G.; Overly, T. B.; Hawley, R. L.; Bradford, J.; Marshall, H. P.

2016-12-01

To better predict the response of the Greenland Ice Sheet (GrIS) to future warming, leading edge Regional Climate Models (RCM) must be calibrated with in situ measurements of recent accumulation and melt. Mass balance estimates averaged across the entire Greenland Ice Sheet (GrIS) vary between models by more than 30 percent, and regional comparisons of mass balance reconstructions in Greenland vary by 100 percent or more. Greenland Traverse for Accumulation and Climate Studies (GreenTrACS) is a multi-year and multi-disciplinary 1700 km science traverse from Raven/Dye2 in SW Greenland, to Summit Station. Multi-offset radar measurements can provide high accuracy electromagnetic (EM) velocity estimates of the firn to within (+-) 0.002 to 0.003 m/ns. EM velocity, in turn, can be used to estimate bulk firn density. Using a mixing equation such as the CRIM Equation we use the measured EM velocity, along with the known EM velocity in air and ice, to estimate bulk density. During spring 2016, we used multi-channel 500MHz radar in a multi-offset configuration to survey more than 800 km from Raven towards summit. Preliminary radar-derived snow density estimates agree with density estimates from a firn core measurement ( 50 kg/m3), despite the lateral heterogeneity of the firn across the length of the antenna array (12 m).

On High-Frequency Topography-Implied Gravity Signals for a Height System Unification Using GOCE-Based Global Geopotential Models

NASA Astrophysics Data System (ADS)

Grombein, Thomas; Seitz, Kurt; Heck, Bernhard

2017-03-01

National height reference systems have conventionally been linked to the local mean sea level, observed at individual tide gauges. Due to variations in the sea surface topography, the reference levels of these systems are inconsistent, causing height datum offsets of up to ±1-2 m. For the unification of height systems, a satellite-based method is presented that utilizes global geopotential models (GGMs) derived from ESA's satellite mission Gravity field and steady-state Ocean Circulation Explorer (GOCE). In this context, height datum offsets are estimated within a least squares adjustment by comparing the GGM information with measured GNSS/leveling data. While the GNSS/leveling data comprises the full spectral information, GOCE GGMs are restricted to long wavelengths according to the maximum degree of their spherical harmonic representation. To provide accurate height datum offsets, it is indispensable to account for the remaining signal above this maximum degree, known as the omission error of the GGM. Therefore, a combination of the GOCE information with the high-resolution Earth Gravitational Model 2008 (EGM2008) is performed. The main contribution of this paper is to analyze the benefit, when high-frequency topography-implied gravity signals are additionally used to reduce the remaining omission error of EGM2008. In terms of a spectral extension, a new method is proposed that does not rely on an assumed spectral consistency of topographic heights and implied gravity as is the case for the residual terrain modeling (RTM) technique. In the first step of this new approach, gravity forward modeling based on tesseroid mass bodies is performed according to the Rock-Water-Ice (RWI) approach. In a second step, the resulting full spectral RWI-based topographic potential values are reduced by the effect of the topographic gravity field model RWI_TOPO_2015, thus, removing the long to medium wavelengths. By using the latest GOCE GGMs, the impact of topography-implied gravity signals on the estimation of height datum offsets is analyzed in detail for representative GNSS/leveling data sets in Germany, Austria, and Brazil. Besides considerable changes in the estimated offset of up to 3 cm, the conducted analyses show that significant improvements of 30-40% can be achieved in terms of a reduced standard deviation and range of the least squares adjusted residuals.

Patients' estimates of their sleep times: reliability and impact on diagnosis of obstructive sleep apnoea.

PubMed

Khor, Y H; Tolson, J; Churchward, T; Rochford, P; Worsnop, C

2015-08-01

Home polysomnography (PSG) is an alternative method for diagnosis of obstructive sleep apnoea (OSA). Some types 3 and 4 PSG do not monitor sleep and so rely on patients' estimation of total sleep time (TST). To compare patients' subjective sleep duration estimation with objective measures in patients who underwent type 2 PSG for probable OSA. A prospective clinical audit of 536 consecutive patients of one of the authors between 2006 and 2013. A standard questionnaire was completed by the patients the morning after the home PSG to record the time of lights being turned off and estimated time of sleep onset and offset. PSG was scored based on the guidelines of the American Academy of Sleep Medicine. Median estimated sleep latency (SL) was 20 min compared with 10 min for measured SL (P < 0.0001). There was also a significant difference between the estimated and measured sleep offset time (median difference = -1 min, P = 0.01). Estimated TST was significantly shorter than the measured TST (median difference = -18.5 min, P = 0.002). No factors have been identified to affect patients' accuracy of sleep perception. Only 2% of patients had a change in their diagnosis of OSA based on calculated apnoea-hypopnoea index. Overall estimated TST in the patients with probable OSA was significantly shorter than measured with significant individual variability. Collectively, inaccurate sleep time estimation had not resulted in significant difference in the diagnosis of OSA. © 2015 Royal Australasian College of Physicians.

Estimation of the long-term slip, surface uplift and block rotation along the northern strand of the North Anatolian Fault Zone: Inferences from geomorphology of the Almacık Block

NASA Astrophysics Data System (ADS)

Yıldırım, Cengiz; Tüysüz, Okan

2017-11-01

The Almacık Block is one of the key morphotectonic units in the eastern Marmara Region associated with the long-term slip partitioning within the North Anatolian Fault Zone (NAFZ). In this study, we provide new geomorphic reconstructions of offset drainage basins, morphometric analysis of topography, and longitudinal profiles of the rivers crossing different flanks of the Almacık Block. Our geomorphic reconstructions of offset drainage basins along the Hendek and Karadere faults imply mean offsets of 2.3 ± 0.4 km and 8.4 ± 0.7 km, respectively, during the Quaternary. Our dataset also imply that slip partitioning occurs in a broader zone than previously proposed, and that the total 10.7 ± 0.6 km offset along the Hendek and Karadere faults of the northern strand must be taken into account for long-term slip partitioning in the Eastern Marmara Region. Together with previously suggested 10 km offset along the southern strand (Yaltırak, 2002), 16 ± 1.0 km offset along the middle strand (Özalp et al., 2013) and the 52 ± 1.0 km offset along the Mudurnu Segment of the northern strand (Akbayram et al., 2016) our newly proposed geomorphic markers raise the cumulative offset in the eastern Marmara region associated with the NAF to 89 ± 1.0 km since the Latest Pliocene - Quaternary. In addition to these lateral displacements, our morphometric analysis and longitudinal profiles of the rivers imply up to 1130 ± 130 m surface uplift of the Almacık Block as a combined result of vertical displacement within the deformation zone of the northern strand of the NAFZ. Finally, by assuming that river basins act as passive deformation markers, our basin azimuth analyses imply 20° ± 2° clockwise rotation of the Almacık Block associated with the NAFZ.

Wavelet extractor: A Bayesian well-tie and wavelet extraction program

NASA Astrophysics Data System (ADS)

Gunning, James; Glinsky, Michael E.

2006-06-01

We introduce a new open-source toolkit for the well-tie or wavelet extraction problem of estimating seismic wavelets from seismic data, time-to-depth information, and well-log suites. The wavelet extraction model is formulated as a Bayesian inverse problem, and the software will simultaneously estimate wavelet coefficients, other parameters associated with uncertainty in the time-to-depth mapping, positioning errors in the seismic imaging, and useful amplitude-variation-with-offset (AVO) related parameters in multi-stack extractions. It is capable of multi-well, multi-stack extractions, and uses continuous seismic data-cube interpolation to cope with the problem of arbitrary well paths. Velocity constraints in the form of checkshot data, interpreted markers, and sonic logs are integrated in a natural way. The Bayesian formulation allows computation of full posterior uncertainties of the model parameters, and the important problem of the uncertain wavelet span is addressed uses a multi-model posterior developed from Bayesian model selection theory. The wavelet extraction tool is distributed as part of the Delivery seismic inversion toolkit. A simple log and seismic viewing tool is included in the distribution. The code is written in Java, and thus platform independent, but the Seismic Unix (SU) data model makes the inversion particularly suited to Unix/Linux environments. It is a natural companion piece of software to Delivery, having the capacity to produce maximum likelihood wavelet and noise estimates, but will also be of significant utility to practitioners wanting to produce wavelet estimates for other inversion codes or purposes. The generation of full parameter uncertainties is a crucial function for workers wishing to investigate questions of wavelet stability before proceeding to more advanced inversion studies.

28 CFR 100.19 - Adjustments to agreement estimate.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the FBI when any change affecting the level of reimbursement occurs. (2) Upon such notification, if..., to the best of the carrier's knowledge and belief, the carrier is entitled to the offset in the...

Emissions of CH4 from natural gas production in the United States using aircraft-based observations (Invited)

NASA Astrophysics Data System (ADS)

Sweeney, C.; Ryerson, T. B.; Karion, A.; Peischl, J.; Petron, G.; Schnell, R. C.; Tsai, T.; Crosson, E.; Rella, C.; Trainer, M.; Frost, G. J.; Hardesty, R. M.; Montzka, S. A.; Dlugokencky, E. J.; Tans, P. P.

2013-12-01

New extraction technologies are making natural gas from shale and tight sand gas reservoirs in the United States (US) more accessible. As a result, the US has become the largest producer of natural gas in the world. This growth in natural gas production may result in increased leakage of methane, a potent greenhouse gas, offsetting the climate benefits of natural gas relative to other fossil fuels. Methane emissions from natural gas production are not well quantified because of the large variety of potential sources, the variability in production and operating practices, the uneven distribution of emitters, and a lack of verification of emission inventories with direct atmospheric measurements. Researchers at the NOAA Earth System Research Laboratory (ESRL) have used simple mass balance approaches to estimate emissions of CH4 from several natural gas and oil plays across the US. We will summarize the results of the available aircraft and ground-based atmospheric emissions estimates to better understand the spatial and temporal distribution of these emissions in the US.

Emissions of CH4 from natural gas production in the United States using aircraft-based observations

NASA Astrophysics Data System (ADS)

Sweeney, Colm; Karion, Anna; Petron, Gabrielle; Ryerson, Thomas; Peischl, Jeff; Trainer, Michael; Rella, Chris; Hardesty, Michael; Crosson, Eric; Montzka, Stephen; Tans, Pieter; Shepson, Paul; Kort, Eric

2014-05-01

New extraction technologies are making natural gas from shale and tight sand gas reservoirs in the United States (US) more accessible. As a result, the US has become the largest producer of natural gas in the world. This growth in natural gas production may result in increased leakage of methane, a potent greenhouse gas, offsetting the climate benefits of natural gas relative to other fossil fuels. Methane emissions from natural gas production are not well quantified because of the large variety of potential sources, the variability in production and operating practices, the uneven distribution of emitters, and a lack of verification of emission inventories with direct atmospheric measurements. Researchers at the NOAA Earth System Research Laboratory (ESRL) have used simple mass balance approaches in combination with isotopes and light alkanes to estimate emissions of CH4 from several natural gas and oil plays across the US. We will summarize the results of the available aircraft and ground-based atmospheric emissions estimates to better understand the spatial and temporal distribution of these emissions in the US.

10 CFR 500.2 - General definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... electric powerplant that produces: (1) Electric power; and (2) Any other form of useful energy (such as... of 1981, Public Law 97-35. OFE means the Office of Fossil Energy of OFE. Offset means “emission...

10 CFR 500.2 - General definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... electric powerplant that produces: (1) Electric power; and (2) Any other form of useful energy (such as... of 1981, Public Law 97-35. OFE means the Office of Fossil Energy of OFE. Offset means “emission...

10 CFR 500.2 - General definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... electric powerplant that produces: (1) Electric power; and (2) Any other form of useful energy (such as... of 1981, Public Law 97-35. OFE means the Office of Fossil Energy of OFE. Offset means “emission...

10 CFR 500.2 - General definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... electric powerplant that produces: (1) Electric power; and (2) Any other form of useful energy (such as... of 1981, Public Law 97-35. OFE means the Office of Fossil Energy of OFE. Offset means “emission...

10 CFR 500.2 - General definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... electric powerplant that produces: (1) Electric power; and (2) Any other form of useful energy (such as... of 1981, Public Law 97-35. OFE means the Office of Fossil Energy of OFE. Offset means “emission...

Health and climate benefits of offshore wind facilities in the Mid-Atlantic United States

DOE PAGES

Buonocore, Jonathan J.; Luckow, Patrick; Fisher, Jeremy; ...

2016-07-14

Electricity from fossil fuels contributes substantially to both climate change and the health burden of air pollution. Renewable energy sources are capable of displacing electricity from fossil fuels, but the quantity of health and climate benefits depend on site-specific attributes that are not often included in quantitative models. Here, we link an electrical grid simulation model to an air pollution health impact assessment model and US regulatory estimates of the impacts of carbon to estimate the health and climate benefits of offshore wind facilities of different sizes in two different locations. We find that offshore wind in the Mid-Atlantic ismore » capable of producing health and climate benefits of between $54 and $120 per MWh of generation, with the largest simulated facility (3000 MW off the coast of New Jersey) producing approximately $690 million in benefits in 2017. The variability in benefits per unit generation is a function of differences in locations (Maryland versus New Jersey), simulated years (2012 versus 2017), and facility generation capacity, given complexities of the electrical grid and differences in which power plants are offset. In the end, this work demonstrates health and climate benefits of off shore wind, provides further evidence of the utility of geographically-refined modeling frameworks, and yields quantitative insights that would allow for inclusion of both climate and public health in benefits assessments of renewable energy.« less

Health and climate benefits of offshore wind facilities in the Mid-Atlantic United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buonocore, Jonathan J.; Luckow, Patrick; Fisher, Jeremy

Electricity from fossil fuels contributes substantially to both climate change and the health burden of air pollution. Renewable energy sources are capable of displacing electricity from fossil fuels, but the quantity of health and climate benefits depend on site-specific attributes that are not often included in quantitative models. Here, we link an electrical grid simulation model to an air pollution health impact assessment model and US regulatory estimates of the impacts of carbon to estimate the health and climate benefits of offshore wind facilities of different sizes in two different locations. We find that offshore wind in the Mid-Atlantic ismore » capable of producing health and climate benefits of between $54 and $120 per MWh of generation, with the largest simulated facility (3000 MW off the coast of New Jersey) producing approximately $690 million in benefits in 2017. The variability in benefits per unit generation is a function of differences in locations (Maryland versus New Jersey), simulated years (2012 versus 2017), and facility generation capacity, given complexities of the electrical grid and differences in which power plants are offset. In the end, this work demonstrates health and climate benefits of off shore wind, provides further evidence of the utility of geographically-refined modeling frameworks, and yields quantitative insights that would allow for inclusion of both climate and public health in benefits assessments of renewable energy.« less

Health and climate benefits of offshore wind facilities in the Mid-Atlantic United States

NASA Astrophysics Data System (ADS)

Buonocore, Jonathan J.; Luckow, Patrick; Fisher, Jeremy; Kempton, Willett; Levy, Jonathan I.

2016-07-01

Electricity from fossil fuels contributes substantially to both climate change and the health burden of air pollution. Renewable energy sources are capable of displacing electricity from fossil fuels, but the quantity of health and climate benefits depend on site-specific attributes that are not often included in quantitative models. Here, we link an electrical grid simulation model to an air pollution health impact assessment model and US regulatory estimates of the impacts of carbon to estimate the health and climate benefits of offshore wind facilities of different sizes in two different locations. We find that offshore wind in the Mid-Atlantic is capable of producing health and climate benefits of between 54 and 120 per MWh of generation, with the largest simulated facility (3000 MW off the coast of New Jersey) producing approximately 690 million in benefits in 2017. The variability in benefits per unit generation is a function of differences in locations (Maryland versus New Jersey), simulated years (2012 versus 2017), and facility generation capacity, given complexities of the electrical grid and differences in which power plants are offset. This work demonstrates health and climate benefits of offshore wind, provides further evidence of the utility of geographically-refined modeling frameworks, and yields quantitative insights that would allow for inclusion of both climate and public health in benefits assessments of renewable energy.

World oilseed situation and U. S. export opportunities, March 1984. Foreign agriculture circular

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-03-01

The world oilseed supply situation tightened in this month with estimated world oilseed, meal and oil production all down from the last month. Reduced peanut and sunflower seed output in drought-damaged areas in Africa more than offset an increase in Argentine soybean output. The protein meal sector remained quiet, with an adjustment in peanut meal production and a reduction in Soviet soybean meal imports. The situation for vegetable and marine oils also remained quiet during the month, with offsetting reductions of Singapore's palm oil imports and exports indicating that country's decline as a transshipper of palm oil.

Evaluation of costs associated with tolvaptan-mediated length-of-stay reduction among heart failure patients with hyponatremia in the US, based on the EVEREST trial.

PubMed

Chiong, Jun R; Kim, Sonnie; Lin, Jay; Christian, Rudell; Dasta, Joseph F

2012-01-01

The Efficacy of Vasopressin Antagonism in Heart Failure Outcome Study with Tolvaptan (EVEREST) trial showed that tolvaptan use improved heart failure (HF) signs and symptoms without serious adverse events. To evaluate the potential cost savings associated with tolvaptan usage among hospitalized hyponatremic HF patients. The Healthcare Cost and Utilization Project (HCUP) 2008 Nationwide Inpatient Sample (NIS) database was used to estimate hospital cost and length of stay (LOS), for diagnosis-related group (DRG) hospitalizations of adult (age ≥18 years) HF patients with complications and comorbidities or major complications and comorbidities. EVEREST trial data for patients with hyponatremia were used to estimate tolvaptan-associated LOS reductions. A cost offset model was constructed to evaluate the impact of tolvaptan on hospital cost and LOS, with univariate and multivariate Monte Carlo sensitivity analyses. Tolvaptan use among hyponatremic EVEREST trial HF patients was associated with shorter hospital LOS than placebo patients (9.72 vs 11.44 days, respectively); 688,336 hospitalizations for HF DRGs were identified from the HCUP NIS database, with a mean LOS of 5.4 days and mean total hospital costs of $8415. Using an inpatient tolvaptan treatment duration of 4 days with a wholesale acquisition cost of $250 per day, the cost offset model estimated a LOS reduction among HF hospitalizations of 0.81 days and an estimated total cost saving of $265 per admission. Univariate and multivariate sensitivity analysis demonstrated that cost reduction associated with tolvaptan usage is consistent among variations of model variables. The estimated LOS reduction and cost savings projected by the cost offset model suggest a clinical and economic benefit to tolvaptan use in hyponatremic HF patients. The EVEREST trial data may not generalize well to the US population. Clinical trial patient profiles and relative LOS reductions may not be applicable to real-world patient populations.

Accounting for the Effect of Earth's Rotation in Magnetotelluric Inference

NASA Astrophysics Data System (ADS)

Riegert, D. L.; Thomson, D. J.

2017-12-01

The study of geomagnetism has been documented as far back as 1722 when the watchmaker G. Graham constructed a more sensitive compass and showed that the variations in geomagnetic direction varied with an irregular daily pattern. Increased interest in geomagnetism in geomagnetism began at the end of the 19th century (Lamb, Schuster, Chapman, and Price). The Magnetotelluric Method was first introduced in the 1950's (Cagniard and Tikhonov), and, at its core, is simply a regression problem. The result of this method is a transfer function estimate which describes the earth's response to magnetic field variations. This estimate can then be used to infer the earth's subsurface structure; useful for applications such as natural resource exploration. The statistical problem of estimating a transfer function between geomagnetic and induced current measurements has evolved since the 1950's due to a variety of problems: non-stationarity, outliers, and violation of Gaussian assumptions. To address some of these issues, robust regression methods (Chave and Thomson, 2004) and the remote reference method (Gambel, 1979) have been proposed and used. The current method seems to provide reasonable estimates, but still requires a large amount of data. Using the multitaper method of spectral analysis (Thomson, 1982), taking long (greater than 4 months) blocks of geomagnetic data, and concentrating on frequencies below 1000 microhertz to avoid ultraviolet effects, one finds that:1) the cross-spectra are dominated by many offset frequencies including plus and minus 1 and 2 cycles per day;2) the coherence at these offset frequencies is often stronger than at zero offset;3) there are strong couplings from the "quasi two-day" cycle;4) frequencines are usually not symmetric;5) the spectra are dominated by the normal modes of the Sun. This talk will discuss the method of incorporating these observations into the transfer function estimation model, some of the difficulties that arose, their solutions, and current results.

Impacts of urban forests on offsetting carbon emissions from industrial energy use in Hangzhou, China.

PubMed

Zhao, Min; Kong, Zheng-hong; Escobedo, Francisco J; Gao, Jun

2010-01-01

This study quantified carbon storage and sequestration by urban forests and carbon emissions from energy consumption by several industrial sources in Hangzhou, China. Carbon (C) storage and sequestration were quantified using urban forest inventory data and by applying volume-derived biomass equations and other models relating net primary productivity (NPP) and mean annual biomass increments. Industrial energy use C emissions were estimated by accounting for fossil fuel use and assigning C emission factors. Total C storage by Hangzhou's urban forests was estimated at 11.74 Tg C, and C storage per hectare was 30.25 t C. Carbon sequestration by urban forests was 1,328, 166.55 t C/year, and C sequestration per ha was 1.66 t C/ha/year. Carbon emissions from industrial energy use in Hangzhou were 7 Tg C/year. Urban forests, through sequestration, annually offset 18.57% of the amount of carbon emitted by industrial enterprises, and store an amount of C equivalent to 1.75 times the amount of annual C emitted by industrial energy uses within the city. Management practices for improving Hangzhou's urban forests function of offsetting C emissions from energy consumption are explored. These results can be used to evaluate the urban forests' role in reducing atmospheric carbon dioxide. Copyright 2009 Elsevier Ltd. All rights reserved.

A cost and policy analysis comparing immediate sequential cataract surgery and delayed sequential cataract surgery from the physician perspective in the United States.

PubMed

Neel, Sean T

2014-11-01

A cost analysis was performed to evaluate the effect on physicians in the United States of a transition from delayed sequential cataract surgery to immediate sequential cataract surgery. Financial and efficiency impacts of this change were evaluated to determine whether efficiency gains could offset potential reduced revenue. A cost analysis using Medicare cataract surgery volume estimates, Medicare 2012 physician cataract surgery reimbursement schedules, and estimates of potential additional office visit revenue comparing immediate sequential cataract surgery with delayed sequential cataract surgery for a single specialty ophthalmology practice in West Tennessee. This model should give an indication of the effect on physicians on a national basis. A single specialty ophthalmology practice in West Tennessee was found to have a cataract surgery revenue loss of $126,000, increased revenue from office visits of $34,449 to $106,271 (minimum and maximum offset methods), and a net loss of $19,900 to $91,700 (base case) with the conversion to immediate sequential cataract surgery. Physicians likely stand to lose financially, and this loss cannot be offset by increased patient visits under the current reimbursement system. This may result in physician resistance to converting to immediate sequential cataract surgery, gaming, and supplier-induced demand.

Integration of ERS and ASAR Time Series for Differential Interferometric SAR Analysis

NASA Astrophysics Data System (ADS)

Werner, C. L.; Wegmüller, U.; Strozzi, T.; Wiesmann, A.

2005-12-01

Time series SAR interferometric analysis requires SAR data with good temporal sampling covering the time period of interest. The ERS satellites operated by ESA have acquired a large global archive of C-Band SAR data since 1991. The ASAR C-Band instrument aboard the ENVISAT platform launched in 2002 operates in the same orbit as ERS-1 and ERS-2 and has largely replaced the remaining operational ERS-2 satellite. However, interferometry between data acquired by ERS and ASAR is complicated by a 31 MHz offset in the radar center frequency between the instruments leading to decorrelation over distributed targets. Only in rare instances, when the baseline exceeds 1 km, can the spectral shift compensate for the difference in the frequencies of the SAR instruments to produce visible fringes. Conversely, point targets do not decorrelate due to the frequency offset making it possible to incorporate the ERS-ASAR phase information and obtain improved temporal coverage. We present an algorithm for interferometric point target analysis that integrates ERS-ERS, ASAR-ASAR and ERS-ASAR data. Initial analysis using the ERS-ERS data is used to identify the phase stable point-like scatterers within the scene. Height corrections relative to the initial DEM are derived by regression of the residual interferometric phases with respect to perpendicular baseline for a set of ERS-ERS interferograms. The ASAR images are coregistered with the ERS scenes and the point phase values are extracted. The different system pixel spacing values between ERS and ASAR requires additional refinement in the offset estimation and resampling procedure. Calculation of the ERS-ASAR simulated phase used to derive the differential interferometric phase must take into account the slightly different carrrier frequencies. Differential ERS-ASAR point phases contain an additional phase component related to the scatterer location within the resolution element. This additional phase varies over several cycles making the differential interferogram appear as uniform phase noise. We present how this point phase difference can be determined and used to correct the ERS-ASAR interferograms. Further processing proceeds as with standard ERS-ERS interferogram stacks utilizing the unwrapped point phases to obtain estimates of the deformation history, and path delay due to variations in tropospheric water vapor. We show and discuss examples demonstrating the success of this approach.

Neural Network Technique for Continous Transition from Ocean to Coastal Retrackers

NASA Astrophysics Data System (ADS)

Hazrina Idris, Nurul; Deng, Xiaoli; Hawani Idris, Nurul

2017-04-01

This paper presents the development of neural network for continuous transition of altimeter sea surface heights when switching from ocean to coastal waveform retrackers. In attempting to produce precise coastal sea level anomaly (SLA) via retracking waveforms, issue arose when employing multiple retracking algorithms (i.e. MLE-4, sub-waveform and threshold). The existence of relative offset between those retrackers creates 'jump' in the retracked SLA profiles. In this study, the offset between retrackers is minimized using multi-layer feed forward neural network technique. The technique reduces the offset values by modelling the complicated functions of those retracked SLAs. The technique is tested over the region of the Great Barrier Reef (GBR), Australia. The validation with Townsville and Bundaberg tide gauges shows that the threshold retracker achieves temporal correlations (r) of 0.84 and 0.75, respectively, and root mean square (RMS) error is 16 cm for both stations, indicating that the retracker produces more accurate SLAs than those of two retrackers. Meanwhile, values of r (RMS error) for MLE-4 is only 0.79 (18 cm) and 0.71 (16 cm), respectively, and for sub-waveform is 0.82 (16 cm) and 0.67 (16 cm), respectively. Therefore, with the neural network, retracked SLAs from MLE-4 and sub-waveform are aligned to those of the threshold retracker. The performance of neural network is compared with the normal procedure of offset removal, which is based on the mean of SLA differences (mean method). The performance is assessed by computing the standard deviation of difference (STD) between the SLAs above a referenced ellipsoid and the geoidal height, and the improvement of percentage (IMP). The results indicate that the neural network provides improvement in SLA precision in all 12 cases, while the mean method provides improvement in 10 out of 12 cases and deterioration is seen in two cases. In terms of STD and IMP, neural network reduces the offset better than those of the mean method. The IMPs with neural network reaches up to 67% for Jason-1 and 73% for Jason-2, meanwhile with mean method the IMPs only reaches up to 28% and 46%, respectively. In conclusion, the neural network technique is efficient to reduce the offset among retrackers by handling the linear and nonlinear relationship between retrackers, thus providing seamless transition from the open ocean to the coast, and vice versa. Studies in currently on-going are to consider other geophysical parameters, such as significant wave height that might be related to the variation of the offset, in the neural network.

Evidence of Fluid/Gas Along the Backthrust Offshore Central Sumatra from Seismic Full Waveform Inversion

NASA Astrophysics Data System (ADS)

Singh, S. C.; Huot, G.

2014-12-01

The Sumatra subduction zone is one of the most seismically active zones on the earth and has experienced great earthquakes in the last decade, including one of the largest earthquakes of the 21st century on December 26, 2004 (M 9.3) producing a devastating tsunami. Geodetic and seismological studies suggest that a part of the subduction is still fully locked and may produce a great earthquake up to Mw=9 in the coming future. In order to understand the earthquake and subduction zone processes, we applied elastic full waveform inversion (FWI) on 50km deep seismic reflection data from Benkulu forearc basin. Data were acquired in partnership with CGG in 2009 using a 15 km ultra-long offset streamer, with shots every 50m and receivers every 12.5m. Unlike usual exploration data, the streamer was dived at 22.5m and the source was triggered at 15m. These characteristics provided wide aperture and low frequencies to the data which are required for FWI. To match our modelling with the observed data before applying FWI, we first estimated the source wavelet from simulated far-offset signature. Then, the same pass-band filter was applied to both the source and the observed data from 1 to 15 Hz frequency bandwidth. Additionally, an f-k filter was applied to the real data to remove the remaining swell noise up to 4 Hz, without losing any useful signal. Our starting 2D Vp model was found by applying traveltime tomography to a smooth 1D model. Our Vs model was linked by empirical relationship to our Vp model. By inverting first for far-offset refraction to recover the background velocity model and using a multi-scale strategy by going from 1Hz to 15Hz, we image the forearc basin down to 10km depth. We highlight the presence of a 10km wide low velocity structure at 3km depth. The sharp velocity change from 4km/s to 2km/s indicates the presence of gaz or fluid which could come from the mantle through the backthrust fault. The complexity of the sea floor makes the reflection challenging to invert but could give higher resolution. We are expecting improvement in the next months.

Low-degree Structure in Mercury's Planetary Magnetic Field

NASA Technical Reports Server (NTRS)

Anderson, Brian J.; Johnson, Catherine L.; Korth, Haje; Winslow, Reka M.; Borovsky, Joseph E.; Purucker, Michael E.; Slavin, James A.; Solomon, Sean C.; Zuber, Maria T.; McNutt, Ralph L. Jr.

2012-01-01

The structure of Mercury's internal magnetic field has been determined from analysis of orbital Magnetometer measurements by the MESSENGER spacecraft. We identified the magnetic equator on 531 low-altitude and 120 high-altitude equator crossings from the zero in the radial cylindrical magnetic field component, Beta (sub rho). The low-altitude crossings are offset 479 +/- 6 km northward, indicating an offset of the planetary dipole. The tilt of the magnetic pole relative to the planetary spin axis is less than 0.8 deg.. The high-altitude crossings yield a northward offset of the magnetic equator of 486 +/- 74 km. A field with only nonzero dipole and octupole coefficients also matches the low-altitude observations but cannot yield off-equatorial Beta (sub rho) = 0 at radial distances greater than 3520 km. We compared offset dipole and other descriptions of the field with vector field observations below 600 km for 13 longitudinally distributed, magnetically quiet orbits. An offset dipole with southward directed moment of 190 nT-R-cube (sub M) yields root-mean-square (RMS) residuals below 14 nT, whereas a field with only dipole and octupole terms tuned to match the polar field and the low-altitude magnetic equator crossings yields RMS residuals up to 68 nT. Attributing the residuals from the offset-dipole field to axial degree 3 and 4 contributions we estimate that the Gauss coefficient magnitudes for the additional terms are less than 4% and 7%, respectively, relative to the dipole. The axial alignment and prominent quadrupole are consistent with a non-convecting layer above a deep dynamo in Mercury's fluid outer core.

Calibration Software for Use with Jurassicprok

NASA Technical Reports Server (NTRS)

Chapin, Elaine; Hensley, Scott; Siqueira, Paul

2004-01-01

The Jurassicprok Interferometric Calibration Software (also called "Calibration Processor" or simply "CP") estimates the calibration parameters of an airborne synthetic-aperture-radar (SAR) system, the raw measurement data of which are processed by the Jurassicprok software described in the preceding article. Calibration parameters estimated by CP include time delays, baseline offsets, phase screens, and radiometric offsets. CP examines raw radar-pulse data, single-look complex image data, and digital elevation map data. For each type of data, CP compares the actual values with values expected on the basis of ground-truth data. CP then converts the differences between the actual and expected values into updates for the calibration parameters in an interferometric calibration file (ICF) and a radiometric calibration file (RCF) for the particular SAR system. The updated ICF and RCF are used as inputs to both Jurassicprok and to the companion Motion Measurement Processor software (described in the following article) for use in generating calibrated digital elevation maps.

Feed-forward frequency offset estimation for 32-QAM optical coherent detection.

PubMed

Xiao, Fei; Lu, Jianing; Fu, Songnian; Xie, Chenhui; Tang, Ming; Tian, Jinwen; Liu, Deming

2017-04-17

Due to the non-rectangular distribution of the constellation points, traditional fast Fourier transform based frequency offset estimation (FFT-FOE) is no longer suitable for 32-QAM signal. Here, we report a modified FFT-FOE technique by selecting and digitally amplifying the inner QPSK ring of 32-QAM after the adaptive equalization, which is defined as QPSK-selection assisted FFT-FOE. Simulation results show that no FOE error occurs with a FFT size of only 512 symbols, when the signal-to-noise ratio (SNR) is above 17.5 dB using our proposed FOE technique. However, the error probability of traditional FFT-FOE scheme for 32-QAM is always intolerant. Finally, our proposed FOE scheme functions well for 10 Gbaud dual polarization (DP)-32-QAM signal to reach 20% forward error correction (FEC) threshold of BER=2×10^-2, under the scenario of back-to-back (B2B) transmission.

The Mars Observer differential one-way range demonstration

NASA Technical Reports Server (NTRS)

Kroger, P. M.; Border, J. S.; Nandi, S.

1994-01-01

Current methods of angular spacecraft positioning using station differenced range data require an additional observation of an extragalactic radio source (quasar) to estimate the timing offset between the reference clocks at the two Deep Space Stations. The quasar observation is also used to reduce the effects of instrumental and media delays on the radio metric observable by forming a difference with the spacecraft observation (delta differential one-way range, delta DOR). An experiment has been completed using data from the Global Positioning System satellites to estimate the station clock offset, eliminating the need for the quasar observation. The requirements for direct measurement of the instrumental delays that must be made in the absence of a quasar observation are assessed. Finally, the results of the 'quasar-free' differential one-way range, or DOR, measurements of the Mars Observer spacecraft are compared with those of simultaneous conventional delta DOR measurements.

AVO Analysis of a Shallow Gas Accumulation in the Marmara Sea

NASA Astrophysics Data System (ADS)

Er, M.; Dondurur, D.; Çifçi, G.

2012-04-01

In recent years, Amplitude versus Offset-AVO analysis is widely used in determination and classification of gas anomalies from wide-offset seismic data. Bright spots which are among the significant factors in determining the hydrocarbon accumulations, can also be determined sucessfully using AVO analysis. A bright spot anomaly were identified on the multi-channel seismic data collected by R/V K. Piri Reis research vessel in the Marmara Sea in 2008. On prestack seismic data, the associated AVO anomalies are clearly identified on the supergathers. Near- and far-offset stack sections are plotted to show the amplitudes changes at different offsets and the bright amplitudes were observed on the far-offset stack. AVO analysis was applied to the observed bright spot anomaly following the standart data processing steps. The analysis includes the preparation of Intercept, Gradient and Fluid Factor sections of AVO attribues. Top and base boundaries of gas bearing sediment were shown by intercept - gradient crossplot method. 1D modelling was also performed to show AVO classes and models were compared with the analysis results. It is interpreted that the bright spot anomaly arises from a shallow gas accumulation. In addition, the gas saturation from P-wave velocity was also estimated by the analysis. AVO analysis indicated Class 3 and Class 4 AVO anomalies observed on the bright spot anomaly.

Development of landsat-5 thematic mapper internal calibrator gain and offset table

USGS Publications Warehouse

Barsi, J.A.; Chander, G.; Micijevic, E.; Markham, B.L.; Haque, Md. O.

2008-01-01

The National Landsat Archive Production System (NLAPS) has been the primary processing system for Landsat data since U.S. Geological Survey (USGS) Earth Resources Observation and Science Center (EROS) started archiving Landsat data. NLAPS converts raw satellite data into radiometrically and geometrically calibrated products. NLAPS has historically used the Internal Calibrator (IC) to calibrate the reflective bands of the Landsat-5 Thematic Mapper (TM), even though the lamps in the IC were less stable than the TM detectors, as evidenced by vicarious calibration results. In 2003, a major effort was made to model the actual TM gain change and to update NLAPS to use this model rather than the unstable IC data for radiometric calibration. The model coefficients were revised in 2007 to reflect greater understanding of the changes in the TM responsivity. While the calibration updates are important to users with recently processed data, the processing system no longer calculates the original IC gain or offset. For specific applications, it is useful to have a record of the gain and offset actually applied to the older data. Thus, the NLAPS calibration database was used to generate estimated daily values for the radiometric gain and offset that might have been applied to TM data. This paper discusses the need for and generation of the NLAPSIC gain and offset tables. A companion paper covers the application of and errors associated with using these tables.

Direct benefits of choosing a high-fitness mate can offset the indirect costs associated with intralocus sexual conflict.

PubMed

Pischedda, Alison; Chippindale, Adam K

2017-06-01

Intralocus sexual conflict generates a cost to mate choice: high-fitness partners transmit genetic variation that confers lower fitness to offspring of the opposite sex. Our earlier work in the fruit fly, Drosophila melanogaster, revealed that these indirect genetic costs were sufficient to reverse potential "good genes" benefits of sexual selection. However, mate choice can also confer direct fitness benefits by inducing larger numbers of progeny. Here, we consider whether direct benefits through enhanced fertility could offset the costs associated with intralocus sexual conflict in D. melanogaster. Using hemiclonal analysis, we found that females mated to high-fitness males produced 11% more offspring compared to those mated to low-fitness males, and high-fitness females produced 34% more offspring than low-fitness females. These direct benefits more than offset the reduction in offspring fitness caused by intralocus sexual conflict, creating a net fitness benefit for each sex to pairing with a high-fitness partner. Our findings highlight the need to consider both direct and indirect effects when investigating the fitness impacts of mate choice. Direct fitness benefits may shelter sexually antagonistic alleles from selection, suggesting a novel mechanism for the maintenance of fitness variation. © 2017 The Author(s). Evolution © 2017 The Society for the Study of Evolution.

Evaluation of Rotor Structural and Aerodynamic Loads using Measured Blade Properties

NASA Technical Reports Server (NTRS)

Jung, Sung N.; You, Young-Hyun; Lau, Benton H.; Johnson, Wayne; Lim, Joon W.

2012-01-01

The structural properties of Higher harmonic Aeroacoustic Rotor Test (HART I) blades have been measured using the original set of blades tested in the wind tunnel in 1994. A comprehensive rotor dynamics analysis is performed to address the effect of the measured blade properties on airloads, blade motions, and structural loads of the rotor. The measurements include bending and torsion stiffness, geometric offsets, and mass and inertia properties of the blade. The measured properties are correlated against the estimated values obtained initially by the manufacturer of the blades. The previously estimated blade properties showed consistently higher stiffnesses, up to 30% for the flap bending in the blade inboard root section. The measured offset between the center of gravity and the elastic axis is larger by about 5% chord length, as compared with the estimated value. The comprehensive rotor dynamics analysis was carried out using the measured blade property set for HART I rotor with and without HHC (Higher Harmonic Control) pitch inputs. A significant improvement on blade motions and structural loads is obtained with the measured blade properties.

Social costs of expanding access to evidence-based supported employment: concepts and interpretive review of evidence.

PubMed

Salkever, David

2013-02-01

A recent policy analysis argued that expanding access to evidence-based supported employment can provide savings in major components of social costs. This article extends the scope of this policy analysis by placing the argument within a recently developed economic framework for social cost-effectiveness analysis that defines a program's social cost impact as its effect on net consumption of all goods and services. A total of 27 studies over the past two decades are reviewed to synthesize evidence of the social cost impacts of expanding access to the individual placement and support model of supported employment (IPS-SE). Most studies have focused primarily on agency costs of providing IPS-SE services, cost offsets when clients shift from "traditional" rehabilitation to IPS-SE, and impacts on clients' earnings. Because costs and cost offsets are similar in magnitude, incremental costs of expanding services to persons who would otherwise receive traditional services are probably small or even negative. The population served by an expansion could be sizable, but the feasibility of a policy targeting IPS-SE expansion in this way has yet to be demonstrated. IPS-SE has positive impacts on competitive job earnings, but these may not fully translate into social cost offsets. Additional empirical support is needed for the argument that large-scale expansion would yield substantial mental health treatment cost offsets. Other gaps in evidence of policy impacts include take-up rate estimates, cost impact estimates from longer-term studies (exceeding two years), and longer-term studies of whether IPS-SE prevents younger clients from becoming recipients of Supplemental Security Income or Social Security Disability Insurance

Measurements and Predictions of the Noise from Three-Stream Jets

NASA Technical Reports Server (NTRS)

Henderson, Brenda S.; Leib, Stewart J.; Wernet, Mark P.

2015-01-01

An experimental and numerical investigation of the noise produced by high-subsonic and supersonic three-stream jets was conducted. The exhaust system consisted of externally-mixed-convergent nozzles and an external plug. Bypass- and tertiary-to-core area ratios between 1.0 and 2.5, and 0.4 and 1.0, respectively, were studied. Axisymmetric and offset tertiary nozzles were investigated for heated and unheated conditions. For axisymmetric configurations, the addition of the third stream was found to reduce peak- and high-frequency acoustic levels in the peak-jet-noise direction, with greater reductions at the lower bypass-to-core area ratios. For the offset configurations, an offset duct was found to decrease acoustic levels on the thick side of the tertiary nozzle relative to those produced by the simulated two-stream jet with up to 8 dB mid-frequency noise reduction at large angles to the jet inlet axis. Noise reduction in the peak-jet-noise direction was greater for supersonic core speeds than for subsonic core speeds. The addition of a tertiary nozzle insert used to divert the third-stream jet to one side of the nozzle system provided no noise reduction. Noise predictions are presented for selected cases using a method based on an acoustic analogy with mean flow interaction effects accounted for using a Green's function, computed in terms of its coupled azimuthal modes for the offset cases, and a source model previously used for round and rectangular jets. Comparisons of the prediction results with data show that the noise model predicts the observed increase in low-frequency noise with the introduction of a third, axisymmetric stream, but not the high-frequency reduction. For an offset third stream, the model predicts the observed trend of decreased sound levels on the thick side of the jet compared with the thin side, but the predicted azimuthal variations are much less than those seen in the data. Also, the shift of the spectral peak to lower frequencies with increasing polar angle is over-predicted. For an offset third stream with a heated core, it is shown that including the enthalpy-flux source terms in the acoustic analogy model improves predictions compared with those obtained using only the momentum flux.

Measurements and Predictions of the Noise from Three-Stream Jets

NASA Technical Reports Server (NTRS)

Henderson, Brenda S.; Leib, Stewart J.; Wernet, Mark P.

2015-01-01

An experimental and numerical investigation of the noise produced by high-subsonic and supersonic three-stream jets was conducted. The exhaust system consisted of externally-mixed-convergent nozzles and an external plug. Bypass- and tertiary- to-core area ratios between 1.0 and 2.5, and 0.4 and 1.0, respectively, were studied. Axisymmetric and offset tertiary nozzles were investigated for heated and unheated conditions. For axisymmetric configurations, the addition of the third stream was found to reduce peak- and high-frequency acoustic levels in the peak-jet-noise direction, with greater reductions at the lower bypass-to-core area ratios. For the offset configurations, an offset duct was found to decrease acoustic levels on the thick side of the tertiary nozzle relative to those produced by the simulated two-stream jet with up to 8 dB mid-frequency noise reduction at large angles to the jet inlet axis. Noise reduction in the peak-jet-noise direction was greater for supersonic core speeds than for subsonic core speeds. The addition of a tertiary nozzle insert used to divert the third-stream jet to one side of the nozzle system provided no noise reduction. Noise predictions are presented for selected cases using a method based on an acoustic analogy with mean flow interaction effects accounted for using a Green's function, computed in terms of its coupled azimuthal modes for the offset cases, and a source model previously used for round and rectangular jets. Comparisons of the prediction results with data show that the noise model predicts the observed increase in low-frequency noise with the introduction of a third, axisymmetric stream, but not the high-frequency reduction. For an offset third stream, the model predicts the observed trend of decreased sound levels on the thick side of the jet compared with the thin side, but the predicted azimuthal variations are much less than those seen in the data. Also, the shift of the spectral peak to lower frequencies with increasing polar angle is over-predicted. For an offset third stream with a heated core, it is shown that including the enthalpy-flux source terms in the acoustic analogy model improves predictions compared with those obtained using only the momentum- flux.

Validating and comparing GNSS antenna calibrations

NASA Astrophysics Data System (ADS)

Kallio, Ulla; Koivula, Hannu; Lahtinen, Sonja; Nikkonen, Ville; Poutanen, Markku

2018-03-01

GNSS antennas have no fixed electrical reference point. The variation of the phase centre is modelled and tabulated in antenna calibration tables, which include the offset vector (PCO) and phase centre variation (PCV) for each frequency according to the elevations and azimuths of the incoming signal. Used together, PCV and PCO reduce the phase observations to the antenna reference point. The remaining biases, called the residual offsets, can be revealed by circulating and rotating the antennas on pillars. The residual offsets are estimated as additional parameters when combining the daily GNSS network solutions with full covariance matrix. We present a procedure for validating the antenna calibration tables. The dedicated test field, called Revolver, was constructed at Metsähovi. We used the procedure to validate the calibration tables of 17 antennas. Tables from the IGS and three different calibration institutions were used. The tests show that we were able to separate the residual offsets at the millimetre level. We also investigated the influence of the calibration tables from the different institutions on site coordinates by performing kinematic double-difference baseline processing of the data from one site with different antenna tables. We found small but significant differences between the tables.

Validation of Maturity Offset in the Fels Longitudinal Study.

PubMed

Malina, Robert M; Choh, Audrey C; Czerwinski, Stefan A; Chumlea, Wm Cameron

2016-08-01

Sex-specific equations for predicting maturity offset, time before or after peak height velocity (PHV), were evaluated in 63 girls and 74 boys from the Fels Longitudinal Study. Serially measured heights (0.1 cm), sitting heights (0.1 cm), weights (0.1 kg), and estimated leg lengths (0.1 cm) from 8 to 18 years were used. Predicted age at PHV (years) was calculated as the difference between chronological age (CA) and maturity offset. Actual age at PHV for each child was derived with a triple logistic model (Bock-Thissen-du Toit). Mean predicted maturity offset was negative and lowest at 8 years and increased linearly with increasing CA. Predicted ages at PHV increased linearly with CA from 8 to 18 years in girls and from 8 to 13 years in boys; predictions varied within relatively narrow limits from 12 to 15 years and then increased to 18 years in boys. Differences between predicted and actual ages at PHV among youth of contrasting maturity status were significant across the age range in both sexes. Dependence of predicted age at PHV upon CA at prediction and on actual age at PHV limits its utility as an indicator of maturity timing and in sport talent programs.

Linking Incoming Plate Faulting and Intermediate Depth Seismicity

NASA Astrophysics Data System (ADS)

Kwong, K. B.; van Zelst, I.; Tong, X.; Eimer, M. O.; Naif, S.; Hu, Y.; Zhan, Z.; Boneh, Y.; Schottenfels, E.; Miller, M. S.; Moresi, L. N.; Warren, J. M.; Wiens, D. A.

2017-12-01

Intermediate depth earthquakes, occurring between 70-350 km depth, are often attributed to dehydration reactions within the subducting plate. It is proposed that incoming plate normal faulting associated with plate bending at the trench may control the amount of hydration in the plate by producing large damage zones that create pathways for the infiltration of seawater deep into the subducting mantle. However, a relationship between incoming plate seismicity, faulting, and intermediate depth seismicity has not been established. We compiled a global dataset consisting of incoming plate earthquake moment tensor (CMT) solutions, focal depths, bend fault spacing and offset measurements, along with plate age and convergence rates. In addition, a global intermediate depth seismicity dataset was compiled with parameters such as the maximum seismic moment and seismicity rate, as well as thicknesses of double seismic zones. The maximum fault offset in the bending region has a strong correlation with the intermediate depth seismicity rate, but a more modest correlation with other parameters such as convergence velocity and plate age. We estimated the expected rate of seismic moment release for the incoming plate faults using mapped fault scarps from bathymetry. We compare this with the cumulative moment from normal faulting earthquakes in the incoming plate from the global CMT catalog to determine whether outer rise fault movement has an aseismic component. Preliminary results from Tonga and the Middle America Trench suggest there may be an aseismic component to incoming plate bending faulting. The cumulative seismic moment calculated for the outer rise faults will also be compared to the cumulative moment from intermediate depth earthquakes to assess whether these parameters are related. To support the observational part of this study, we developed a geodynamic numerical modeling study to systematically explore the influence of parameters such as plate age and convergence rate on the offset, depth, and spacing of outer rise faults. We then compare these robust constraints on outer rise faulting to the observed widths of intermediate depth earthquakes globally.

Inspired gas humidity and temperature during mechanical ventilation with the Stephanie ventilator.

PubMed

Preo, Bianca L; Shadbolt, Bruce; Todd, David A

2013-11-01

To measure inspired gas humidity and temperature delivered by a Stephanie neonatal ventilator with variations in (i) circuit length; (ii) circuit insulation; (iii) proximal airway temperature probe (pATP) position; (iv) inspiratory temperature (offset); and (v) incubator temperatures. Using the Stephanie neonatal ventilator, inspired gas humidity and temperature were measured during mechanical ventilation at the distal inspiratory limb and 3 cm down the endotracheal tube. Measurements were made with a long or short circuit; with or without insulation of the inspiratory limb; proximal ATP (pATP) either within or external to the incubator; at two different inspiratory temperature (offset) of 37(-0.5) and 39(-2.0)°C; and at three different incubator temperatures of 32, 34.5, and 37°C. Long circuits produced significantly higher inspired humidity than short circuits at all incubator settings, while only at 32°C was the inspired temperature higher. In the long circuits, insulation further improved the inspired humidity especially at 39(-2.0)°C, while only at incubator temperatures of 32 and 37°C did insulation significantly improve inspired temperature. Positioning the pATP outside the incubator did not result in higher inspired humidity but did significantly improve inspired temperature. An inspiratory temperature (offset) of 39(-2.0)°C delivered significantly higher inspired humidity and temperature than the 37(-0.5)°C especially when insulated. Long insulated Stephanie circuits should be used for neonatal ventilation when the infant is nursed in an incubator. The recommended inspiratory temperature (offset) of 37(-0.5)°C produced inspired humidity and temperature below international standards, and we suggest an increase to 39(-2.0)°C. © 2013 John Wiley & Sons Ltd.

Energy balance and emissions associated with biochar sequestration and pyrolysis bioenergy production.

PubMed

Gaunt, John L; Lehmann, Johannes

2008-06-01

The implications for greenhouse gas emissions of optimizing a slow pyrolysis-based bioenergy system for biochar and energy production rather than solely for energy production were assessed. Scenarios for feedstock production were examined using a life-cycle approach. We considered both purpose grown bioenergy crops (BEC) and the use of crop wastes (CW) as feedstocks. The BEC scenarios involved a change from growing winter wheat to purpose grown miscanthus, switchgrass, and corn as bioenergy crops. The CW scenarios consider both corn stover and winter wheat straw as feedstocks. Our findings show that the avoided emissions are between 2 and 5 times greater when biochar is applied to agricultural land (2--19 Mg CO2 ha(-1) y(-1)) than used solely for fossil energy offsets. 41--64% of these emission reductions are related to the retention of C in biochar, the rest to offsetting fossil fuel use for energy, fertilizer savings, and avoided soil emissions other than CO2. Despite a reduction in energy output of approximately 30% where the slow pyrolysis technology is optimized to produce biochar for land application, the energy produced per unit energy input at 2--7 MJ/MJ is greater than that of comparable technologies such as ethanol from corn. The C emissions per MWh of electricity production range from 91-360 kg CO2 MWh(-1), before accounting for C offset due to the use of biochar are considerably below the lifecycle emissions associated with fossil fuel use for electricity generation (600-900 kg CO2 MWh(-1)). Low-temperature slow pyrolysis offers an energetically efficient strategy for bioenergy production, and the land application of biochar reduces greenhouse emissions to a greater extent than when the biochar is used to offset fossil fuel emissions.

An LMS Programming Scheme and Floating-Gate Technology Enabled Trimmer-Less and Low Voltage Flame Detection Sensor.

PubMed

Iglesias-Rojas, Juan Carlos; Gomez-Castañeda, Felipe; Moreno-Cadenas, Jose Antonio

2017-06-14

In this paper, a Least Mean Square (LMS) programming scheme is used to set the offset voltage of two operational amplifiers that were built using floating-gate transistors, enabling a 0.95 V RMS trimmer-less flame detection sensor. The programming scheme is capable of setting the offset voltage over a wide range of values by means of electron injection. The flame detection sensor consists of two programmable offset operational amplifiers; the first amplifier serves as a 26 μV offset voltage follower, whereas the second amplifier acts as a programmable trimmer-less voltage comparator. Both amplifiers form the proposed sensor, whose principle of functionality is based on the detection of the electrical changes produced by the flame ionization. The experimental results show that it is possible to measure the presence of a flame accurately after programming the amplifiers with a maximum of 35 LMS-algorithm iterations. Current commercial flame detectors are mainly used in absorption refrigerators and large industrial gas heaters, where a high voltage AC source and several mechanical trimmings are used in order to accurately measure the presence of the flame.

Temperature and Voltage Offsets in High- ZT Thermoelectrics

NASA Astrophysics Data System (ADS)

Levy, George S.

2018-06-01

Thermodynamic temperature can take on different meanings. Kinetic temperature is an expectation value and a function of the kinetic energy distribution. Statistical temperature is a parameter of the distribution. Kinetic temperature and statistical temperature, identical in Maxwell-Boltzmann statistics, can differ in other statistics such as those of Fermi-Dirac or Bose-Einstein when a field is present. Thermal equilibrium corresponds to zero statistical temperature gradient, not zero kinetic temperature gradient. Since heat carriers in thermoelectrics are fermions, the difference between these two temperatures may explain voltage and temperature offsets observed during meticulous Seebeck measurements in which the temperature-voltage curve does not go through the origin. In conventional semiconductors, temperature offsets produced by fermionic electrical carriers are not observable because they are shorted by heat phonons in the lattice. In high- ZT materials, however, these offsets have been detected but attributed to faulty laboratory procedures. Additional supporting evidence for spontaneous voltages and temperature gradients includes data collected in epistatic experiments and in the plasma Q-machine. Device fabrication guidelines for testing the hypothesis are suggested including using unipolar junctions stacked in a superlattice, alternating n/ n + and p/ p + junctions, selecting appropriate dimensions, doping, and loading.

Temperature and Voltage Offsets in High-ZT Thermoelectrics

NASA Astrophysics Data System (ADS)

Levy, George S.

2017-10-01

Thermodynamic temperature can take on different meanings. Kinetic temperature is an expectation value and a function of the kinetic energy distribution. Statistical temperature is a parameter of the distribution. Kinetic temperature and statistical temperature, identical in Maxwell-Boltzmann statistics, can differ in other statistics such as those of Fermi-Dirac or Bose-Einstein when a field is present. Thermal equilibrium corresponds to zero statistical temperature gradient, not zero kinetic temperature gradient. Since heat carriers in thermoelectrics are fermions, the difference between these two temperatures may explain voltage and temperature offsets observed during meticulous Seebeck measurements in which the temperature-voltage curve does not go through the origin. In conventional semiconductors, temperature offsets produced by fermionic electrical carriers are not observable because they are shorted by heat phonons in the lattice. In high-ZT materials, however, these offsets have been detected but attributed to faulty laboratory procedures. Additional supporting evidence for spontaneous voltages and temperature gradients includes data collected in epistatic experiments and in the plasma Q-machine. Device fabrication guidelines for testing the hypothesis are suggested including using unipolar junctions stacked in a superlattice, alternating n/n + and p/p + junctions, selecting appropriate dimensions, doping, and loading.

An LMS Programming Scheme and Floating-Gate Technology Enabled Trimmer-Less and Low Voltage Flame Detection Sensor

PubMed Central

Iglesias-Rojas, Juan Carlos; Gomez-Castañeda, Felipe; Moreno-Cadenas, Jose Antonio

2017-01-01

In this paper, a Least Mean Square (LMS) programming scheme is used to set the offset voltage of two operational amplifiers that were built using floating-gate transistors, enabling a 0.95 VRMS trimmer-less flame detection sensor. The programming scheme is capable of setting the offset voltage over a wide range of values by means of electron injection. The flame detection sensor consists of two programmable offset operational amplifiers; the first amplifier serves as a 26 μV offset voltage follower, whereas the second amplifier acts as a programmable trimmer-less voltage comparator. Both amplifiers form the proposed sensor, whose principle of functionality is based on the detection of the electrical changes produced by the flame ionization. The experimental results show that it is possible to measure the presence of a flame accurately after programming the amplifiers with a maximum of 35 LMS-algorithm iterations. Current commercial flame detectors are mainly used in absorption refrigerators and large industrial gas heaters, where a high voltage AC source and several mechanical trimmings are used in order to accurately measure the presence of the flame. PMID:28613250

Vocal release time: a quantification of vocal offset.

PubMed

Watson, Ben C; Roark, Rick M; Baken, R J

2012-11-01

To determine the vocal release time (VRT) for linguistically unconstrained voice offsets in a healthy young adult population. Sound pressure (SP) and electroglottographic (EGG) recordings were obtained for 57 female and 55 male subjects while producing multiple tokens of three tasks (sustained /ɑ:/, "always," and "hallways") at comfortable pitch and loudness. SP and EGG signals were digitally time reversed and generalized sinusoidal models of the SP and EGG signals were obtained to compare rates of amplitude change. VRT was computed from the time lag of the cross-correlation function. Adjusted mean VRT values were significantly greater for females than for males. There was no systematic effect of age on VRT. However, 25-29-year old and >40 year old females showed shorter VRT values than the youngest female age group. Normative data are presented for a new measure of the duration of vocal offset, VRT. Acquisition of this measure requires little user intervention, thereby minimizing effects of subjective decision making. Comparison with previously reported vocal attack time (VAT) values for the same population suggests phenomenological differences between linguistically and physiologically constrained voice onsets and unconstrained voice offsets. Copyright © 2012 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

Gas-fired power in the UK: Bridging supply gaps and implications of domestic shale gas exploitation for UK climate change targets.

PubMed

Turk, Jeremy K; Reay, David S; Haszeldine, R Stuart

2018-03-01

There is a projected shortcoming in the fourth carbon budget of 7.5%. This shortfall may be increased if the UK pursues a domestic shale gas industry to offset projected decreases in traditional gas supply. Here we estimate that, if the project domestic gas supply gap for power generation were to be met by UK shale gas with low fugitive emissions (0.08%), an additional 20.4MtCO 2 e 1 would need to be accommodated during carbon budget periods 3-6. We find that a modest fugitive emissions rate (1%) for UK shale gas would increase global emissions compared to importing an equal quantity of Qatari liquefied natural gas. Additionally, we estimate that natural gas electricity generation would emit 420-466MtCO 2 e (460 central estimate) during the same time period within the traded EU emissions cap. We conclude that domestic shale gas production with even a modest 1% fugitive emissions rate would risk exceedance of UK carbon budgets. We also highlight that, under the current production-based greenhouse gas accounting system, the UK is incentivized to import natural gas rather than produce it domestically. Copyright © 2017 Elsevier B.V. All rights reserved.

Martian Wrinkle Ridge Topography: Evidence for Subsurface Faults from MOLA

NASA Technical Reports Server (NTRS)

Golombek, M. P.; Anderson, F. S.; Zuber, M. T.

2000-01-01

Mars Orbiter Laser Altimeter (MOLA) profiles across wrinkle ridges are characterized by plains surfaces at different elevations on either side that appear best explained by subsurface thrust faults that underlie the ridges and produce the offset.

The carbon footprint of laparoscopic surgery: should we offset?

PubMed

Gilliam, A D; Davidson, B; Guest, J

2008-02-01

The aim of this study was to estimate the effect that the expansion of laparoscopic surgery has had on global warming. Laparoscopic procedures performed in a hospital over a 10-year period were analysed. The number of CO(2) cylinders (size C) used over a 2.5-year period and the "carbon footprint" of each cylinder was calculated. There was a fourfold increase of in the number of laparoscopic procedures performed over the past 10 years (n = 174-688). Median operative time for the laparoscopic procedures performed over the past 2.5-years (n = 1629) was 1.01 h (range 0.3-4.45 h) with 415 cylinders used in this period giving an operative time per cylinder of 3.96 h. Each cylinder produces only 0.0009 of tonnes of CO(2). Despite increasing frequency of the laparoscopic approach in general surgery, its impact on global warming is negligible.

Economical and Environmentally Benign Extraction of Rare Earth Elements (REES) from Coal & Coal Byproducts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlson, Gary

This final report provides a complete summary of the activities, results, analytical discussion, and overall evaluation of the project titled “Economical and Environmentally Benign Extraction of Rare Earth Elements (REES) from Coal & Coal Byproducts” under DOE Award Number DE-FE-0027155 that started in March 2016 and ended December 2017. Fly ash was selected as the coal-byproduct source material due to fact that it is readily available with no need for extensive methods to obtain the material, it is produced in large quantities (>50 million tons per year) and had REE concentrations similar to other coal-byproducts. The selected fly ash usedmore » throughout this project was from the Mill Creek power generating facility operated by Louisville Gas and Electric located in Louisville, KY and was subjected to a variety of physical and chemical characterization tests. Results from fusion extractions showed that the selected fly-ash had a TREE+Y concentration of 480 ppm with critical REEs concentration of 200 ppm. The fly ash had an outlook ratio of 1.25 and an estimated value of $16-$18 worth of salable REEs per 1-tonne of fly ash. Additional characterizations by optical evaluation, QEMSCAN, XRD, size fractionation, and SEM analysis showed the fly ash consisted of small glassy spherules with a size range between 1 to 110 µm (ave. diam. of 13 um), was heterogeneous in chemical composition (main crystalline phases: aluminum oxides and iron oxides) and was primarily an amorphous material (75 to 80%). A simple stepped approach was completed to estimate the total REE resource quantity. The approach included REE characterization of the representative samples, evaluation of fly-ash availability, and final determination estimated resource availability with regards to REE grade on a regional and national scale. This data represents the best available information and is based upon the assumptions that the power generating facility where the fly-ash was obtained will use the same coal sources (actual mines were identified), the coal materials will have relatively consistent REE concentrations, and the REE extraction process developed during this project can achieve 42% REE recovery (validated and confirmed). Calculations indicated that the estimated REE resource is approximately 175,000 tonnes with a current estimated value of $3,330MM. The proposed REE extraction and production process developed during this project used four fundamental steps; 1) fly-ash pretreatment to enhance REE extraction, 2) REE extraction by acid digestion, 3) REE separation/concentration by carbon adsorption and column chromatography, and 4) REE oxide production. Secondary processing steps to manage process residuals and additional processing techniques to produce value-added products were incorporated into the process during the project. These secondary steps were not only necessary to manage residuals, but also provided additional revenue streams that offset operational and capital expenditures. The process produces one value product stream (production of zeolite Na-P1), a solids waste stream, and one liquid stream that met RCRA discharge requirements. Based upon final design criteria and operational parameters, the proposed system could produce approximately 200 grams of REOs from 1-tonne of fly-ash, thereby representing a TREE+Y recovery of 42% (project target of > 25%). A detailed economic model was developed to evaluate both CAPEX and OPEX estimates for systems with varying capacities between 100 kg to 200 tonnes of fly ash processed per day. Using a standard system capacity of 10 tonne/day system, capital costs were estimated at $88/kg fly ash while operating costs were estimated at approximately $450/kg fly ash. This operating cost estimate includes a revenue of $495/tonne of fly ash processed from the value-added product produced from the system (zeolite Na-P1). Although operating cost savings due to zeolite production were significant, the capital + operating cost for a 10 tonne system was more expensive than the total dollar value of REEs present in the fly ash material. Specifically, the estimated cost per 1-tonne of fly ash treated is approximately $540 while the estimated value of REEs in the fly ash is $18-$20/tonne. This is an excessive difference showing that the proposed process is not economically feasible strictly on the basis of REE revenue compared to extraction costs. Although the current proposed system does not produce sufficient quantities of REEs or additional revenue sources to offset operational and capital costs, supplementary factors including US strategic concerns, commercial demands, and defense department requirements must be factored. At this time, the process developed during this project provides foundational information for future development of simple processes that require low capital investment and one that will extract a valuable quality and quantity of REE oxides from industrial waste.« less

Quantitative estimation of minimum offset for multichannel surface-wave survey with actively exciting source

USGS Publications Warehouse

Xu, Y.; Xia, J.; Miller, R.D.

2006-01-01

Multichannel analysis of surface waves is a developing method widely used in shallow subsurface investigations. The field procedures and related parameters are very important for successful applications. Among these parameters, the source-receiver offset range is seldom discussed in theory and normally determined by empirical or semi-quantitative methods in current practice. This paper discusses the problem from a theoretical perspective. A formula for quantitatively evaluating a layered homogenous elastic model was developed. The analytical results based on simple models and experimental data demonstrate that the formula is correct for surface wave surveys for near-surface applications. ?? 2005 Elsevier B.V. All rights reserved.

Basin-fill Aquifer Modeling with Terrestrial Gravity: Assessing Static Offsets in Bulk Datasets using MATLAB; Case Study of Bridgeport, CA

NASA Astrophysics Data System (ADS)

Mlawsky, E. T.; Louie, J. N.; Pohll, G.; Carlson, C. W.; Blakely, R. J.

2015-12-01

Understanding the potential availability of water resources in Eastern California aquifers is of critical importance to making water management policy decisions and determining best-use practices for California, as well as for downstream use in Nevada. Hydrologic well log data can provide valuable information on aquifer capacity, but is often proprietarily inaccessible or economically unfeasible to obtain in sufficient quantity. In the case of basin-fill aquifers, it is possible to make estimates of aquifer geometry and volume using geophysical surveys of gravity, constrained by additional geophysical and geological observations. We use terrestrial gravity data to model depth-to-basement about the Bridgeport, CA basin for application in preserving the Walker Lake biome. In constructing the model, we assess several hundred gravity observations, existing and newly collected. We regard these datasets as "bulk," as the data are compiled from multiple sources. Inconsistencies among datasets can result in "static offsets," or artificial bull's-eye contours, within the gradient. Amending suspect offsets requires the attention of the modeler; picking these offsets by hand can be a time-consuming process when modeling large-scale basin features. We develop a MATLAB script for interpolating the residual Bouguer anomaly about the basin using sparse observation points, and leveling offset points with a user-defined sensitivity. The script is also capable of plotting gravity profiles between any two endpoints within the map extent. The resulting anomaly map provides an efficient means of locating and removing static offsets in the data, while also providing a fast visual representation of a bulk dataset. Additionally, we obtain gridded basin gravity models with an open-source alternative to proprietary modeling tools.

Surface Rupture and Slip Distribution Resulting from the 2013 M7.7 Balochistan, Pakistan Earthquake

NASA Astrophysics Data System (ADS)

Reitman, N. G.; Gold, R. D.; Briggs, R. W.; Barnhart, W. D.; Hayes, G. P.

2014-12-01

The 24 September 2013 M7.7 earthquake in Balochistan, Pakistan, produced a ~200 km long left-lateral strike-slip surface rupture along a portion of the Hoshab fault, a moderately dipping (45-75º) structure in the Makran accretionary prism. The rupture is remarkably continuous and crosses only two (0.7 and 1.5 km wide) step-overs along its arcuate path through southern Pakistan. Displacements are dominantly strike-slip, with a minor component of reverse motion. We remotely mapped the surface rupture at 1:5,000 scale and measured displacements using high resolution (0.5 m) pre- and post-event satellite imagery. We mapped 295 laterally faulted stream channels, terrace margins, and roads to quantify near-field displacement proximal (±10 m) to the rupture trace. The maximum near-field left-lateral offset is 15±2 m (average of ~7 m). Additionally, we used pre-event imagery to digitize 254 unique landforms in the "medium-field" (~100-200 m from the rupture) and then measured their displacements compared to the post-event imagery. At this scale, maximum left-lateral offset approaches 17 m (average of ~8.5 m). The width (extent of observed surface faulting) of the rupture zone varies from ~1 m to 3.7 km. Near- and medium-field offsets show similar slip distributions that are inversely correlated with the width of the fault zone at the surface (larger offsets correspond to narrow fault zones). The medium-field offset is usually greater than the near-field offset. The along-strike surface slip distribution is highly variable, similar to the slip distributions documented for the 2002 Denali M7.9 earthquake and 2001 Kunlun M7.8 earthquake, although the Pakistan offsets are larger in magnitude. The 2013 Pakistan earthquake ranks among the largest documented continental strike-slip displacements, possibly second only to the 18+ m surface displacements attributed to the 1855 Wairarapa M~8.1 earthquake.

North American terrestrial CO 2 uptake largely offset by CH 4 and N 2O emissions: toward a full accounting of the greenhouse gas budget

DOE PAGES

Tian, Hanqin; Chen, Guangsheng; Lu, Chaoqun; ...

2014-03-14

The terrestrial ecosystems of North America have been identified as a sink of atmospheric CO 2 though there is no consensus on the magnitude. However, the emissions of non-CO 2 greenhouse gases (CH 4 and N 2O) may offset or even overturn the climate cooling effect induced by the CO 2 sink. Using a coupled biogeochemical model, in this study, we have estimated the combined global warming potentials (GWP) of CO 2, CH 4 and N 2O fluxes in North American terrestrial ecosystems and quantified the relative contributions of environmental factors to the GWP changes during 1979–2010. The uncertainty rangemore » for contemporary global warming potential has been quantified by synthesizing the existing estimates from inventory, forward modeling, and inverse modeling approaches. Our “best estimate” of net GWP for CO 2, CH 4 and N 2O fluxes was₋0.50 ± 0.27 Pg CO 2 eq/year (1 Pg=1015 g) in North American terrestrial ecosystems during 2001–2010. The emissions of CH 4 and N 2O from terrestrial ecosystems had offset about two thirds (73% ± 14%) of the land CO 2 sink in the North American continent, showing large differences across the three countries, with offset ratios of 57% ± 8% in US, 83% ± 17 % in Canada and 329% ± 119 % in Mexico. Climate change and elevated tropospheric ozone concentration have contributed the most to GWP increase, while elevated atmospheric CO 2 concentration have contributed the most to GWP reduction. Extreme drought events over certain periods could result in a positive GWP. By integrating the existing estimates, we have found a wide range of uncertainty for the combined GWP. In conclusion, from both climate change science and policy perspectives, it is necessary to integrate ground and satellite observations with models for a more accurate accounting of these three greenhouse gases in North America.« less

Ultrasonic Doppler measurement of renal artery blood flow

NASA Technical Reports Server (NTRS)

Freund, W. R.; Beaver, W. L.; Meindl, J. D.

1976-01-01

Studies were made of (1) blood flow redistribution during lower body negative pressure (LBNP), (2) the profile of blood flow across the mitral annulus of the heart (both perpendicular and parallel to the commissures), (3) testing and evaluation of a number of pulsed Doppler systems, (4) acute calibration of perivascular Doppler transducers, (5) redesign of the mitral flow transducers to improve reliability and ease of construction, and (6) a frequency offset generator designed for use in distinguishing forward and reverse components of blood flow by producing frequencies above and below the offset frequency. Finally methodology was developed and initial results were obtained from a computer analysis of time-varying Doppler spectra.

Optimization of spherical facets for parabolic solar concentrators

NASA Technical Reports Server (NTRS)

White, J. E.; Erikson, R. J.; Sturgis, J. D.; Elfe, T. B.

1986-01-01

Solar concentrator designs which employ deployable hexagonal panels are being developed for space power systems. An offset optical configuration has been developed which offers significant system level advantages over previously proposed collector designs for space applications. Optical analyses have been performed which show offset reflector intercept factors to be only slightly lower than those for symmetric reflectors with the same slope error. Fluxes on the receiver walls are asymmetric but manageable by varying the tilt angle of the receiver. Greater producibility is achieved by subdividing the hexagonal panels into triangular mirror facets of spherical contour. Optical analysis has been performed upon these to yield near-optimum sizes and radii.

Investigating Strain Transfer Along the Southern San Andreas Fault: A Geomorphic and Geodetic Study of Block Rotation in the Eastern Transverse Ranges, Joshua Tree National Park, CA

NASA Astrophysics Data System (ADS)

Guns, K. A.; Bennett, R. A.; Blisniuk, K.

2017-12-01

To better evaluate the distribution and transfer of strain and slip along the Southern San Andreas Fault (SSAF) zone in the northern Coachella valley in southern California, we integrate geological and geodetic observations to test whether strain is being transferred away from the SSAF system towards the Eastern California Shear Zone through microblock rotation of the Eastern Transverse Ranges (ETR). The faults of the ETR consist of five east-west trending left lateral strike slip faults that have measured cumulative offsets of up to 20 km and as low as 1 km. Present kinematic and block models present a variety of slip rate estimates, from as low as zero to as high as 7 mm/yr, suggesting a gap in our understanding of what role these faults play in the larger system. To determine whether present-day block rotation along these faults is contributing to strain transfer in the region, we are applying 10Be surface exposure dating methods to observed offset channel and alluvial fan deposits in order to estimate fault slip rates along two faults in the ETR. We present observations of offset geomorphic landforms using field mapping and LiDAR data at three sites along the Blue Cut Fault and one site along the Smoke Tree Wash Fault in Joshua Tree National Park which indicate recent Quaternary fault activity. Initial results of site mapping and clast count analyses reveal at least three stages of offset, including potential Holocene offsets, for one site along the Blue Cut Fault, while preliminary 10Be geochronology is in progress. This geologic slip rate data, combined with our new geodetic surface velocity field derived from updated campaign-based GPS measurements within Joshua Tree National Park will allow us to construct a suite of elastic fault block models to elucidate rates of strain transfer away from the SSAF and how that strain transfer may be affecting the length of the interseismic period along the SSAF.

Boundary Layer Instabilities Generated by Freestream Laser Perturbations

NASA Technical Reports Server (NTRS)

Chou, Amanda; Schneider, Steven P.

2015-01-01

A controlled, laser-generated, freestream perturbation was created in the freestream of the Boeing/AFOSR Mach-6 Quiet Tunnel (BAM6QT). The freestream perturbation convected downstream in the Mach-6 wind tunnel to interact with a flared cone model. The geometry of the flared cone is a body of revolution bounded by a circular arc with a 3-meter radius. Fourteen PCB 132A31 pressure transducers were used to measure a wave packet generated in the cone boundary layer by the freestream perturbation. This wave packet grew large and became nonlinear before experiencing natural transition in quiet flow. Breakdown of this wave packet occurred when the amplitude of the pressure fluctuations was approximately 10% of the surface pressure for a nominally sharp nosetip. The initial amplitude of the second mode instability on the blunt flared cone is estimated to be on the order of 10 -6 times the freestream static pressure. The freestream laser-generated perturbation was positioned upstream of the model in three different configurations: on the centerline, offset from the centerline by 1.5 mm, and offset from the centerline by 3.0 mm. When the perturbation was offset from the centerline of a blunt flared cone, a larger wave packet was generated on the side toward which the perturbation was offset. The offset perturbation did not show as much of an effect on the wave packet on a sharp flared cone as it did on a blunt flared cone.

Identification of Geomorphic Conditions Favoring Preservation of Multiple Individual Displacements Across Transform Faults

NASA Astrophysics Data System (ADS)

Williams, P. L.; Phillips, D. A.; Bowles-Martinez, E.; Masana, E.; Stepancikova, P.

2010-12-01

Terrestrial and airborne LiDAR data, and low altitude aerial photography have been utilized in conjunction with field work to identify and map single and multiple-event stream-offsets along all strands of the San Andreas fault in the Coachella Valley. Goals of the work are characterizing the range of displacements associated with the fault’s prehistoric surface ruptures, evaluating patterns of along-fault displacement, and disclosing processes associated with the prominent Banning-Mission Creek fault junction. Preservation offsets is associated with landscape conditions including: (1) well-confined and widely spaced source streams up-slope of the fault; (2) persistent geomorphic surfaces below the fault; (3) slope directions oriented approximately perpendicular to the fault. Notably, a pair of multiple-event offset sites have been recognized in coarse fan deposits below the Mission Creek fault near 1000 Palms oasis. Each of these sites is associated with a single source drainage oriented approximately perpendicular to the fault, and preserves a record of individual fault displacements affecting the southern portion of the Mission Creek branch of the San Andreas fault. The two sites individually record long (>10 event) slip-per-event histories. Documentation of the sites indicates a prevalence of moderate displacements and a small number of large offsets. This is consistent with evidence developed in systematic mapping of individual and multiple event stream offsets in the area extending 70 km south to Durmid Hill. Challenges to site interpretation include the presence of closely spaced en echelon fault branches and indications of stream avulsion in the area of the modern fault crossing. Conversely, strong bar and swale topography produce high quality offset indicators that can be identified across en echelon branches in most cases. To accomplish the detailed mapping needed to fully recover the complex yet well-preserved geomorphic features under investigation, a program of terrestrial laser scanning (TLS) was conducted at the 1000 Palms oasis stream offset sites. Data products and map interpretations will be presented along with initial applications of the study to characterizing San Andreas fault rupture hazard. Continuing work will seek to more fully populate the dataset of larger offsets, evaluate means to objectively date the larger offsets, and, as completely as possible, to characterize magnitudes of past surface ruptures of the San Andreas fault in the Coachella Valley.

Deviation of Long-Period Tides from Equilibrium: Kinematics and Geostrophy

NASA Technical Reports Server (NTRS)

Egbert, Gary D.; Ray, Richard D.

2003-01-01

New empirical estimates of the long-period fortnightly (Mf) tide obtained from TOPEX/Poseidon (T/P) altimeter data confirm significant basin-scale deviations from equilibrium. Elevations in the low-latitude Pacific have reduced amplitude and lag those in the Atlantic by 30 deg or more. These interbasin amplitude and phase variations are robust features that are reproduced by numerical solutions of the shallow-water equations, even for a constant-depth ocean with schematic interconnected rectangular basins. A simplified analytical model for cooscillating connected basins also reproduces the principal features observed in the empirical solutions. This simple model is largely kinematic. Zonally averaged elevations within a simple closed basin would be nearly in equilibrium with the gravitational potential, except for a constant offset required to conserve mass. With connected basins these offsets are mostly eliminated by interbasin mass flux. Because of rotation, this flux occurs mostly in a narrow boundary layer across the mouth and at the western edge of each basin, and geostrophic balance in this zone supports small residual offsets (and phase shifts) between basins. The simple model predicts that this effect should decrease roughly linearly with frequency, a result that is confirmed by numerical modeling and empirical T/P estimates of the monthly (Mm) tidal constituent. This model also explains some aspects of the anomalous nonisostatic response of the ocean to atmospheric pressure forcing at periods of around 5 days.

The potential carbon benefit of reforesting Hawai‘i Island non-native grasslands with endemic Acacia koa trees

USGS Publications Warehouse

Selmants, Paul; Sleeter, Benjamin M.; Koch, Nicholas; Friday, James B.; Ohara, Rebekah Dickens; Friday, James B.

2016-01-01

Large areas of forest in the tropics have been cleared and converted to pastureland. Hawai‘i Island is no exception, with over 100,000 ha of historically forested land now dominated by non-native grasses. Passive forest restoration has been unsuccessful because these grasslands tend to persist even after grazers have been removed, yet active outplanting of native tree species can be cost-prohibitive at the landscape scale. It is therefore essential to seek co-benefits of forest restoration to defray costs, such as accredited carbon offsets from increased carbon sequestration. We developed a reforestation scenario for non-native grasslands on Hawai‘i Island by outplanting endemic koa (Acacia koa) trees paid for with carbon offsets via the California Cap and Trade Program. This scenario entails reforesting 53,531 ha of non-native grassland at 2500 ha y-1 over 22 years. We estimated planting costs at \\$6,178 ha-1, a total cost of approximately \\$331,000,000. We used the Land Use and Carbon Simulator (LUCAS) model to estimate island-wide ecosystem carbon sequestration with and without koa reforestation using 100 Monte Carlo simulations per year over a 60-year period. Income from carbon offsets was set at \\$13.57 per ton of CO2 equivalent, the current California Cap and Trade Program carbon market price.

Waveform identification and retracking analyses of Jason-2 altimeter satellite data for improving sea surface height estimation in Southern Java Island Waters and Java Sea, Indonesia

NASA Astrophysics Data System (ADS)

Nababan, Bisman; Hakim, Muhammad R.; Panjaitan, James P.

2018-05-01

Indonesian waters containing many small islands and shallow waters leads to a less accurate of sea surface height (SSH) estimation from satellite altimetry. Little efforts are also given for the validation of SSH estimation from the satellite in Indonesian waters. The purpose of this research was to identify and retrack waveforms of Jason-2 altimeter satellite data in southern Java island waters and Java Sea using several retrackers and performed improvement percentage analyses for new SSH estimation. The study used data of the Sensor Geophysical Data Record type D (SGDR-D) of Jason-2 satellite altimeter of the year 2010 in the southern Java island waters and 2012-2014 in Java Sea. Waveform retracking analyses were conducted using several retrackers (Offset Center of Gravity, Ice, Threshold, and Improved Threshold) and examined using a world reference undulation geoid of EGM08 and Oceanic retracker. Result showed that shape and pattern of waveforms were varied in all passes, seasons, and locations specifically along the coastal regions. In general, non-Brownish and complex waveforms were identified along coastal region specifically within the distance of 0-10 km from the shoreline. In contrary, generally Brownish waveforms were found in offshore. However, Brownish waveform can also be found within coastal region and non-Brownish waveforms within offshore region. The results were also showed that the four retrackers produced a better SSH estimation in coastal region. However, there was no dominant retracker to improve the accuracy of the SSH estimate.

Safety evaluation of offset improvements for left-turn lanes

DOT National Transportation Integrated Search

2009-06-01

The Federal Highway Administration (FHWA) organized 26 States to participate in the FHWA Low Cost Safety Improvements Pooled Fund Study as part of its strategic highway safety plan support effort. The purpose of the pooled fund study is to estimate t...

Improved Tracking of an Atomic-Clock Resonance Transition

NASA Technical Reports Server (NTRS)

Prestage, John D.; Chung, Sang K.; Tu, Meirong

2010-01-01

An improved method of making an electronic oscillator track the frequency of an atomic-clock resonance transition is based on fitting a theoretical nonlinear curve to measurements at three oscillator frequencies within the operational frequency band of the transition (in other words, at three points within the resonance peak). In the measurement process, the frequency of a microwave oscillator is repeatedly set at various offsets from the nominal resonance frequency, the oscillator signal is applied in a square pulse of the oscillator signal having a suitable duration (typically, of the order of a second), and, for each pulse at each frequency offset, fluorescence photons of the transition in question are counted. As described below, the counts are used to determine a new nominal resonance frequency. Thereafter, offsets are determined with respect to the new resonance frequency. The process as described thus far is repeated so as to repeatedly adjust the oscillator to track the most recent estimate of the nominal resonance frequency.

Role of electron-phonon coupling and thermal expansion on band gaps, carrier mobility, and interfacial offsets in kesterite thin-film solar cells

NASA Astrophysics Data System (ADS)

Monserrat, Bartomeu; Park, Ji-Sang; Kim, Sunghyun; Walsh, Aron

2018-05-01

The efficiencies of solar cells based on kesterite Cu2ZnSnS4 (CZTS) and Cu2ZnSnSe4 (CZTSe) are limited by a low open-circuit voltage due to high rates of non-radiative electron-hole recombination. To probe the origin of this bottleneck, we calculate the band offset of CZTS(Se) with CdS, confirming a weak spike of 0.1 eV for CZTS/wurtzite-CdS and a strong spike of 0.4 eV for CZTSe/wurtzite-CdS. We also consider the effects of temperature on the band alignment, finding that increasing temperature significantly enhances the spike-type offset. We further resolve an outstanding discrepancy between the measured and calculated phonon frequencies for the kesterites, and use these to estimate the upper limit of electron and hole mobilities based on optic phonon Fröhlich scattering, which uncovers an intrinsic asymmetry with faster (minority carrier) electron mobility.

Beam based alignment and its relevance in Indus-2.

PubMed

Jena, Saroj Kumar; Husain, Riyasat; Gandhi, M L; Agrawal, R K; Yadav, S; Ghodke, A D

2015-09-01

Initially in the Indus-2 storage ring, the closed orbit distortion (COD) could be best corrected to 1.3 mm rms in the horizontal and 0.43 mm rms in the vertical plane. The strength of the corrector magnets required high values for COD correction. This revealed that offsets in COD readout by the beam position monitors (BPMs) played a role in not achieving a rms COD lower than the above value. Thus, the offset between the electrical center of BPMs and the magnetic center of the nearest quadrupole magnet could be estimated using the beam based alignment (BBA) method. It prefers that the quadrupole magnet is able to be controlled individually and active shunt power supply (ASPS) system was designed for this purpose that works efficiently. This paper describes the methodology of BBA, topology of ASPS and its performance, and COD minimization using the measured BPM offsets. After BBA, the COD could be reduced to 0.45 mm rms and 0.2 mm rms in horizontal and vertical planes, respectively.

Beam based alignment and its relevance in Indus-2

NASA Astrophysics Data System (ADS)

Jena, Saroj Kumar; Husain, Riyasat; Gandhi, M. L.; Agrawal, R. K.; Yadav, S.; Ghodke, A. D.

2015-09-01

Initially in the Indus-2 storage ring, the closed orbit distortion (COD) could be best corrected to 1.3 mm rms in the horizontal and 0.43 mm rms in the vertical plane. The strength of the corrector magnets required high values for COD correction. This revealed that offsets in COD readout by the beam position monitors (BPMs) played a role in not achieving a rms COD lower than the above value. Thus, the offset between the electrical center of BPMs and the magnetic center of the nearest quadrupole magnet could be estimated using the beam based alignment (BBA) method. It prefers that the quadrupole magnet is able to be controlled individually and active shunt power supply (ASPS) system was designed for this purpose that works efficiently. This paper describes the methodology of BBA, topology of ASPS and its performance, and COD minimization using the measured BPM offsets. After BBA, the COD could be reduced to 0.45 mm rms and 0.2 mm rms in horizontal and vertical planes, respectively.

Optical Substructure and BCG Offsets of Sunyaev-Zel'dovich and X-ray Selected Galaxy Clusters

NASA Astrophysics Data System (ADS)

Lopes, Paulo AA; Trevisan, M.; Laganá, T. F.; Durret, F.; Ribeiro, A. LB; Rembold, S. B.

2018-05-01

We used optical imaging and spectroscopic data to derive substructure estimates for local Universe (z < 0.11) galaxy clusters from two different samples. The first was selected through the Sunyaev-Zel'dovich (SZ) effect by the Planck satellite and the second is an X-ray selected sample. In agreement to X-ray substructure estimates we found that the SZ systems have a larger fraction of substructure than the X-ray clusters. We have also found evidence that the higher mass regime of the SZ clusters, compared to the X-ray sample, explains the larger fraction of disturbed objects in the Planck data. Although we detect a redshift evolution in the substructure fraction, it is not sufficient to explain the different results between the higher-z SZ sample and the X-ray one. We have also verified a good agreement (˜60%) between the optical and X-ray substructure estimates. However, the best level of agreement is given by the substructure classification given by measures based on the brightest cluster galaxy (BCG), either the BCG-X-ray centroid offset, or the magnitude gap between the first and second BCGs. We advocate the use of those two parameters as the most reliable and cheap way to assess cluster dynamical state. We recommend an offset cut of ˜0.01 ×R500 to separate relaxed and disturbed clusters. Regarding the magnitude gap the separation can be done at Δm12 = 1.0. The central galaxy paradigm (CGP) may not be valid for ˜20% of relaxed massive clusters. This fraction increases to ˜60% for disturbed systems.

Cocaine-like discriminative stimulus effects of phendimetrazine and phenmetrazine in rats.

PubMed

Bauer, Clayton T; Negus, S Stevens; Blough, Bruce E; Banks, Matthew L

2016-04-01

Phendimetrazine is a clinically available anorectic and candidate medication for the treatment of cocaine addiction. Phendimetrazine can be metabolized to the amphetamine-like monoamine releaser phenmetrazine, but it is unclear if phendimetrazine functions as an inactive prodrug or might have activity on its own. As one method to address this issue, the present study compared the potency and time course of phendimetrazine and phenmetrazine to produce cocaine-like discriminative stimulus effects in adult, male rats (N=5) trained to discriminate cocaine (5.6 mg/kg, intraperitoneally) from saline in a two-key food-reinforced discrimination procedure. We hypothesized that, if metabolism to phenmetrazine was required for phendimetrazine effects, then phendimetrazine would be less potent and have a slower onset and offset of effects than phenmetrazine. Both phendimetrazine and phenmetrazine produced dose-dependent cocaine-like discriminative stimulus effects, and phendimetrazine was 7.8-fold less potent than phenmetrazine. However, the time courses of discriminative stimulus effects produced by phendimetrazine and phenmetrazine were similar, with peak effects at 10 min and offset by 100 min. These results show the effectiveness of phendimetrazine to rapidly produce cocaine-like behavioral effects in rats and support other nonhuman primate evidence to suggest that metabolism to phenmetrazine may not be required for phendimetrazine effects.

Estimating rooftop solar technical potential across the US using a combination of GIS-based methods, lidar data, and statistical modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gagnon, Pieter; Margolis, Robert; Melius, Jennifer

We provide a detailed estimate of the technical potential of rooftop solar photovoltaic (PV) electricity generation throughout the contiguous United States. This national estimate is based on an analysis of select US cities that combines light detection and ranging (lidar) data with a validated analytical method for determining rooftop PV suitability employing geographic information systems. We use statistical models to extend this analysis to estimate the quantity and characteristics of roofs in areas not covered by lidar data. Finally, we model PV generation for all rooftops to yield technical potential estimates. At the national level, 8.13 billion m 2 ofmore » suitable roof area could host 1118 GW of PV capacity, generating 1432 TWh of electricity per year. This would equate to 38.6% of the electricity that was sold in the contiguous United States in 2013. This estimate is substantially higher than a previous estimate made by the National Renewable Energy Laboratory. The difference can be attributed to increases in PV module power density, improved estimation of building suitability, higher estimates of total number of buildings, and improvements in PV performance simulation tools that previously tended to underestimate productivity. Also notable, the nationwide percentage of buildings suitable for at least some PV deployment is high—82% for buildings smaller than 5000 ft 2 and over 99% for buildings larger than that. In most states, rooftop PV could enable small, mostly residential buildings to offset the majority of average household electricity consumption. Even in some states with a relatively poor solar resource, such as those in the Northeast, the residential sector has the potential to offset around 100% of its total electricity consumption with rooftop PV.« less

Estimating rooftop solar technical potential across the US using a combination of GIS-based methods, lidar data, and statistical modeling

DOE PAGES

Gagnon, Pieter; Margolis, Robert; Melius, Jennifer; ...

2018-01-05

We provide a detailed estimate of the technical potential of rooftop solar photovoltaic (PV) electricity generation throughout the contiguous United States. This national estimate is based on an analysis of select US cities that combines light detection and ranging (lidar) data with a validated analytical method for determining rooftop PV suitability employing geographic information systems. We use statistical models to extend this analysis to estimate the quantity and characteristics of roofs in areas not covered by lidar data. Finally, we model PV generation for all rooftops to yield technical potential estimates. At the national level, 8.13 billion m 2 ofmore » suitable roof area could host 1118 GW of PV capacity, generating 1432 TWh of electricity per year. This would equate to 38.6% of the electricity that was sold in the contiguous United States in 2013. This estimate is substantially higher than a previous estimate made by the National Renewable Energy Laboratory. The difference can be attributed to increases in PV module power density, improved estimation of building suitability, higher estimates of total number of buildings, and improvements in PV performance simulation tools that previously tended to underestimate productivity. Also notable, the nationwide percentage of buildings suitable for at least some PV deployment is high—82% for buildings smaller than 5000 ft 2 and over 99% for buildings larger than that. In most states, rooftop PV could enable small, mostly residential buildings to offset the majority of average household electricity consumption. Even in some states with a relatively poor solar resource, such as those in the Northeast, the residential sector has the potential to offset around 100% of its total electricity consumption with rooftop PV.« less

Estimating rooftop solar technical potential across the US using a combination of GIS-based methods, lidar data, and statistical modeling

NASA Astrophysics Data System (ADS)

Gagnon, Pieter; Margolis, Robert; Melius, Jennifer; Phillips, Caleb; Elmore, Ryan

2018-02-01

We provide a detailed estimate of the technical potential of rooftop solar photovoltaic (PV) electricity generation throughout the contiguous United States. This national estimate is based on an analysis of select US cities that combines light detection and ranging (lidar) data with a validated analytical method for determining rooftop PV suitability employing geographic information systems. We use statistical models to extend this analysis to estimate the quantity and characteristics of roofs in areas not covered by lidar data. Finally, we model PV generation for all rooftops to yield technical potential estimates. At the national level, 8.13 billion m2 of suitable roof area could host 1118 GW of PV capacity, generating 1432 TWh of electricity per year. This would equate to 38.6% of the electricity that was sold in the contiguous United States in 2013. This estimate is substantially higher than a previous estimate made by the National Renewable Energy Laboratory. The difference can be attributed to increases in PV module power density, improved estimation of building suitability, higher estimates of total number of buildings, and improvements in PV performance simulation tools that previously tended to underestimate productivity. Also notable, the nationwide percentage of buildings suitable for at least some PV deployment is high—82% for buildings smaller than 5000 ft2 and over 99% for buildings larger than that. In most states, rooftop PV could enable small, mostly residential buildings to offset the majority of average household electricity consumption. Even in some states with a relatively poor solar resource, such as those in the Northeast, the residential sector has the potential to offset around 100% of its total electricity consumption with rooftop PV.

Spatial optimization of carbon-stocking projects across Africa integrating stocking potential with co-benefits and feasibility.

PubMed

Greve, Michelle; Reyers, Belinda; Mette Lykke, Anne; Svenning, Jens-Christian

2013-01-01

Carbon offset projects through forestation are employed within the emissions trading framework to store carbon. Yet, information about the potential of landscapes to stock carbon, essential to the design of offset projects, is often lacking. Here, based on data on vegetation carbon, climate and soil, we quantify the potential for carbon storage in woody vegetation across tropical Africa. The ability of offset projects to produce co-benefits for ecosystems and people is then quantified. When co-benefits such as biodiversity conservation are considered, the top-ranked sites are sometimes different to sites selected purely for their carbon-stocking potential, although they still possess up to 92% of the latter carbon-stocking potential. This work provides the first continental-scale assessment of which areas may provide the greatest direct and indirect benefits from carbon storage reforestation projects at the smallest costs and risks, providing crucial information for prioritization of investments in carbon storage projects.

A Novel Application of the Multichannel Analysis of Surface Waves (MASW) Method for Estimating the Critical Zone Thicknes

NASA Astrophysics Data System (ADS)

Nelson, S.; Yaede, J.; McBride, J. H.; Park, C.; Turnbull, S. J.; Tingey, D. G.

2014-12-01

MASW approaches are suitable for the accurate measurement of variably thick weathering profiles by producing shear-wave (Vs) profiles. The critical zone (CZ) base is usually a transitional boundary, which is captured by MASW but not by conventional seismic reflection techniques. Modified MASW methods were used in Hawaii, USA to extend the investigative depth of saprolite (kaolin clays, Fe-oxides) thickness calibrated against wells with geologic logs. Active-source ± passive dispersion curves produced improved low-frequency fundamental modes by combining records with varying source-receiver offsets, enabling the generation of Vs profiles to >50 m depth. The top of unaltered bedrock occurs at a Vs of >~500 m/s. Intra-saprolite high Vs zones probably represent aa flow interiors with fewer primary discontinuities (vesicles and fractures), therefore imparting higher secondary stiffness than altered pahoehoe and pyroclastic material. The MASW approach permits measuring CZ thicknesses at discrete locations rapidly, inexpensively, and without drilling. For example, employed on slopes of the Koolau Volcano (neither aggrading nor degrading), the downward rate of advance of the weathering front of the CZ varies from 0.02 to 0.03 mm/yr in wet and ~0.01 mm/yr in dry areas. This compares well with recent work based on solute mass fluxes averaged over large areas. MASW can be deployed in a variety of settings where rapid estimation of the CZ thickness at particular locations is desired.

The stonehenge technique: a new method of crystal alignment for coherent bremsstrahlung experiments

NASA Astrophysics Data System (ADS)

Livingston, Kenneth

2005-08-01

In the coherent bremsstrahlung technique a thin diamond crystal oriented correctly in an electron beam can produce photons with a high degree of linear polarization.1 The crystal is mounted on a goniometer to control its orientation and it is necessary to measure the angular offsets a) between the crystal axes and the goniometer axes and b) between the goniometer and the electron beam axis. A method for measuring these offsets and aligning the crystal was developed by Lohman et al, and has been used successfully in Mainz.2 However, recent attempts to investigate new crystals have shown that this approach has limitations which become more serious at higher beam energies where more accurate setting of the crystal angles, which scale with l/Ebeam, is required. (Eg. the recent installation of coherent bremsstrahlung facility at Jlab, with Ebeam = 6 GeV ) This paper describes a new, more general alignment technique, which overcomes these limitations. The technique is based on scans where the horizontal and vertical rotation axes of the goniometer are adjusted in a series of steps to make the normal to the crystal describe a cone of a given angle. For each step in the scan, the photon energy spectrum is measured using a tagging spectrometer, and the offsets between the electron beam and the crystal lattice are inferred from the resulting 2D plot. Using this method, it is possible to align the crystal with the beam quickly, and hence to set any desired orientation of the crystal relative to the beam. This is essential for any experiment requiring linearly polarized photons produced via coherent bremsstrahlung, and is also required for a systematic study of the channeling radiation produced by the electron beam incident on the crystal.

Multiple-Bit Differential Detection of OQPSK

NASA Technical Reports Server (NTRS)

Simon, Marvin

2005-01-01

A multiple-bit differential-detection method has been proposed for the reception of radio signals modulated with offset quadrature phase-shift keying (offset QPSK or OQPSK). The method is also applicable to other spectrally efficient offset quadrature modulations. This method is based partly on the same principles as those of a multiple-symbol differential-detection method for M-ary QPSK, which includes QPSK (that is, non-offset QPSK) as a special case. That method was introduced more than a decade ago by the author of the present method as a means of improving performance relative to a traditional (two-symbol observation) differential-detection scheme. Instead of symbol-by-symbol detection, both that method and the present one are based on a concept of maximum-likelihood sequence estimation (MLSE). As applied to the modulations in question, MLSE involves consideration of (1) all possible binary data sequences that could have been received during an observation time of some number, N, of symbol periods and (2) selection of the sequence that yields the best match to the noise-corrupted signal received during that time. The performance of the prior method was shown to range from that of traditional differential detection for short observation times (small N) to that of ideal coherent detection (with differential encoding) for long observation times (large N).

A collinearity diagnosis of the GNSS geocenter determination

NASA Astrophysics Data System (ADS)

Rebischung, Paul; Altamimi, Zuheir; Springer, Tim

2014-01-01

The problem of observing geocenter motion from global navigation satellite system (GNSS) solutions through the network shift approach is addressed from the perspective of collinearity (or multicollinearity) among the parameters of a least-squares regression. A collinearity diagnosis, based on the notion of variance inflation factor, is therefore developed and allows handling several peculiarities of the GNSS geocenter determination problem. Its application reveals that the determination of all three components of geocenter motion with GNSS suffers from serious collinearity issues, with a comparable level as in the problem of determining the terrestrial scale simultaneously with the GNSS satellite phase center offsets. The inability of current GNSS, as opposed to satellite laser ranging, to properly sense geocenter motion is mostly explained by the estimation, in the GNSS case, of epoch-wise station and satellite clock offsets simultaneously with tropospheric parameters. The empirical satellite accelerations, as estimated by most Analysis Centers of the International GNSS Service, slightly amplify the collinearity of the geocenter coordinate, but their role remains secondary.

High-throughput sample adaptive offset hardware architecture for high-efficiency video coding

NASA Astrophysics Data System (ADS)

Zhou, Wei; Yan, Chang; Zhang, Jingzhi; Zhou, Xin

2018-03-01

A high-throughput hardware architecture for a sample adaptive offset (SAO) filter in the high-efficiency video coding video coding standard is presented. First, an implementation-friendly and simplified bitrate estimation method of rate-distortion cost calculation is proposed to reduce the computational complexity in the mode decision of SAO. Then, a high-throughput VLSI architecture for SAO is presented based on the proposed bitrate estimation method. Furthermore, multiparallel VLSI architecture for in-loop filters, which integrates both deblocking filter and SAO filter, is proposed. Six parallel strategies are applied in the proposed in-loop filters architecture to improve the system throughput and filtering speed. Experimental results show that the proposed in-loop filters architecture can achieve up to 48% higher throughput in comparison with prior work. The proposed architecture can reach a high-operating clock frequency of 297 MHz with TSMC 65-nm library and meet the real-time requirement of the in-loop filters for 8 K × 4 K video format at 132 fps.

Dual-band beacon experiment over Southeast Asia for ionospheric irregularity analysis

NASA Astrophysics Data System (ADS)

Watthanasangmechai, K.; Yamamoto, M.; Saito, A.; Saito, S.; Maruyama, T.; Tsugawa, T.; Nishioka, M.

2013-12-01

An experiment of dual-band beacon over Southeast Asia was started in March 2012 in order to capture and analyze ionospheric irregularities in equatorial region. Five GNU Radio Beacon Receivers (GRBRs) were aligned along 100 degree geographic longitude. The distances between the stations reach more than 500 km. The field of view of this observational network covers +/- 20 degree geomagnetic latitude including the geomagnetic equator. To capture ionospheric irregularities, the absolute TEC estimation technique was developed. The two-station method (Leitinger et al., 1975) is generally accepted as a suitable method to estimate TEC offsets of dual-band beacon experiment. However, the distances between the stations directly affect on the robustness of the technique. In Southeast Asia, the observational network is too sparse to attain a benefit of the classic two-station method. Moreover, the least-squares approch used in the two-station method tries too much to adjust the small scales of the TEC distribution which are the local minima. We thus propose a new technique to estimate the TEC offsets with the supporting data from absolute GPS-TEC from local GPS receivers and the ionospheric height from local ionosondes. The key of the proposed technique is to utilize the brute-force technique with weighting function to find the TEC offset set that yields a global minimum of RMSE in whole parameter space. The weight is not necessary when the TEC distribution is smooth, while it significantly improves the TEC estimation during the ESF events. As a result, the latitudinal TEC shows double-hump distribution because of the Equatorial Ionization Anomaly (EIA). In additions, the 100km-scale fluctuations from an Equatorial Spread F (ESF) are captured at night time in equinox seasons. The plausible linkage of the meridional wind with triggering of ESF is under invatigating and will be presented. The proposed method is successful to estimate the latitudinal TEC distribution from dual-band frequency beacon data for the sparse observational network in Southeast Asia which may be useful for other equatorial sectors like Affrican region as well.

THE APPLICATION AND DEVELOPMENT OF APPROPRIATE TOOLS AND TECHNOLOGIES FOR COST-EFFECTIVE CARBON SEQUESTRATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bill Stanley; Sandra Brown; Ellen Hawes

2002-09-01

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research projects is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects,more » providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas impacts. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: advanced videography testing; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.« less

Substantial global carbon uptake by cement carbonation

NASA Astrophysics Data System (ADS)

Xi, Fengming; Davis, Steven J.; Ciais, Philippe; Crawford-Brown, Douglas; Guan, Dabo; Pade, Claus; Shi, Tiemao; Syddall, Mark; Lv, Jie; Ji, Lanzhu; Bing, Longfei; Wang, Jiaoyue; Wei, Wei; Yang, Keun-Hyeok; Lagerblad, Björn; Galan, Isabel; Andrade, Carmen; Zhang, Ying; Liu, Zhu

2016-12-01

Calcination of carbonate rocks during the manufacture of cement produced 5% of global CO2 emissions from all industrial process and fossil-fuel combustion in 2013. Considerable attention has been paid to quantifying these industrial process emissions from cement production, but the natural reversal of the process--carbonation--has received little attention in carbon cycle studies. Here, we use new and existing data on cement materials during cement service life, demolition, and secondary use of concrete waste to estimate regional and global CO2 uptake between 1930 and 2013 using an analytical model describing carbonation chemistry. We find that carbonation of cement materials over their life cycle represents a large and growing net sink of CO2, increasing from 0.10 GtC yr-1 in 1998 to 0.25 GtC yr-1 in 2013. In total, we estimate that a cumulative amount of 4.5 GtC has been sequestered in carbonating cement materials from 1930 to 2013, offsetting 43% of the CO2 emissions from production of cement over the same period, not including emissions associated with fossil use during cement production. We conclude that carbonation of cement products represents a substantial carbon sink that is not currently considered in emissions inventories.

RB Particle Filter Time Synchronization Algorithm Based on the DPM Model.

PubMed

Guo, Chunsheng; Shen, Jia; Sun, Yao; Ying, Na

2015-09-03

Time synchronization is essential for node localization, target tracking, data fusion, and various other Wireless Sensor Network (WSN) applications. To improve the estimation accuracy of continuous clock offset and skew of mobile nodes in WSNs, we propose a novel time synchronization algorithm, the Rao-Blackwellised (RB) particle filter time synchronization algorithm based on the Dirichlet process mixture (DPM) model. In a state-space equation with a linear substructure, state variables are divided into linear and non-linear variables by the RB particle filter algorithm. These two variables can be estimated using Kalman filter and particle filter, respectively, which improves the computational efficiency more so than if only the particle filter was used. In addition, the DPM model is used to describe the distribution of non-deterministic delays and to automatically adjust the number of Gaussian mixture model components based on the observational data. This improves the estimation accuracy of clock offset and skew, which allows achieving the time synchronization. The time synchronization performance of this algorithm is also validated by computer simulations and experimental measurements. The results show that the proposed algorithm has a higher time synchronization precision than traditional time synchronization algorithms.

Gamma-Ray Pulsar Light Curves in Vacuum and Force-Free Geometry

NASA Technical Reports Server (NTRS)

Harding, Alice K.; DeCesar, Megan E.; Miller, M. Coleman; Kalapotharakos, Constantinos; Contopoulos, Ioannis

2011-01-01

Recent studies have shown that gamma-ray pulsar light curves are very sensitive to the geometry of the pulsar magnetic field. Pulsar magnetic field geometries, such as the retarded vacuum dipole and force-free magnetospheres have distorted polar caps that are offset from the magnetic axis in the direction opposite to rotation. Since this effect is due to the sweepback of field lines near the light cylinder, offset polar caps are a generic property of pulsar magnetospheres and their effects should be included in gamma-ray pulsar light curve modeling. In slot gap models (having two-pole caustic geometry), the offset polar caps cause a strong azimuthal asymmetry of the particle acceleration around the magnetic axis. We have studied the effect of the offset polar caps in both retarded vacuum dipole and force-free geometry on the model high-energy pulse profiles. We find that, compared to the profiles derived from symmetric caps, the flux in the pulse peaks, which are caustics formed along the trailing magnetic field lines, increases significantly relative to the off-peak emission, formed along leading field lines. The enhanced contrast produces improved slot gap model fits to Fermi pulsar light curves like Vela, with vacuum dipole fits being more favorable.

Effect of head contact on the rim of the cup on the offset loading and torque in hip joint replacement.

PubMed

Liu, Feng; Williams, Sophie; Jin, Zhongmin; Fisher, John

2013-11-01

Head contact on the rim of the cup causes stress concentration and consequently increased wear. The head contact on the rim of the cup may in addition cause an offset load and torque on the cup. The head-rim contact resulting from microseparation or subluxation has been investigated. An analytical model has been developed to calculate the offset loading and resultant torque on the cup as a function of the translational displacement of the head under simplified loading condition of the hip joint at heel strike during a walking cycle. The magnitude of the torque on the cup was found to increase with the increasing translational displacement, larger diameter heads, eccentric cups, and the coefficient of friction of the contact. The effects of cup inclination, cup rim radius, and cup coverage angle on the magnitude of the torque were found to be relatively small with a maximum variation in the torque magnitude being lower than 20%. This study has shown an increased torque due to the head loading on the rim of the cup, and this may contribute to the incidence of cup loosening. Particularly, metal-on-metal hip joints with larger head diameters may produce the highest offset loading torque.

Theoretical and simulated performance for a novel frequency estimation technique

NASA Technical Reports Server (NTRS)

Crozier, Stewart N.

1993-01-01

A low complexity, open-loop, discrete-time, delay-multiply-average (DMA) technique for estimating the frequency offset for digitally modulated MPSK signals is investigated. A nonlinearity is used to remove the MPSK modulation and generate the carrier component to be extracted. Theoretical and simulated performance results are presented and compared to the Cramer-Rao lower bound (CRLB) for the variance of the frequency estimation error. For all signal-to-noise ratios (SNR's) above threshold, it is shown that the CRLB can essentially be achieved with linear complexity.

Installation and early performance of a field test section of asphalt rubber concrete.

DOT National Transportation Integrated Search

1991-01-01

Asphalt rubber, which is produced by reacting asphalt cement and crumb rubber, is claimed to increase fatigue life and reduce rutting of asphalt concrete; however, the service life must be increased significantly to offset the additional coast of add...

Power Up with Methane Gas: Struthers Water Pollution Control Facility

EPA Pesticide Factsheets

The city of Struthers received $5.4 million in ARRA funding from the Ohio’s CWSRF for a project that uses methane gas produced at the Struthers Water Pollution Control Facility to power unit treatment processes and offset the facility’s energy footprint.

Dynamical Instability Produces Transform Faults at Mid-Ocean Ridges

NASA Astrophysics Data System (ADS)

Gerya, Taras

2010-08-01

Transform faults at mid-ocean ridges—one of the most striking, yet enigmatic features of terrestrial plate tectonics—are considered to be the inherited product of preexisting fault structures. Ridge offsets along these faults therefore should remain constant with time. Here, numerical models suggest that transform faults are actively developing and result from dynamical instability of constructive plate boundaries, irrespective of previous structure. Boundary instability from asymmetric plate growth can spontaneously start in alternate directions along successive ridge sections; the resultant curved ridges become transform faults within a few million years. Fracture-related rheological weakening stabilizes ridge-parallel detachment faults. Offsets along the transform faults change continuously with time by asymmetric plate growth and discontinuously by ridge jumps.

System and method for mass production of graphene platelets in arc plasma

DOEpatents

Keidar, Michael; Shashurin, Alexey

2017-12-12

A system and method for producing graphene includes a discharge assembly and a substrate assembly. The discharge assembly includes a cathode and an anode, which in one embodiment are offset from each other. The anode produces a flux stream that is deposited onto a substrate. A collection device removes the deposited material from the rotating substrate. The flux stream can be a carbon vapor, with the deposited flux being graphene.

Modeling right-lateral offset of a Late Pleistocene terrace riser along the Polaris fault using ground based LiDAR imagery

NASA Astrophysics Data System (ADS)

Howle, J. F.; Bawden, G. W.; Hunter, L. E.; Rose, R. S.

2009-12-01

High resolution (centimeter level) three-dimensional point-cloud imagery of offset glacial outwash deposits were collected by using ground based tripod LiDAR (T-LiDAR) to characterize the cumulative fault slip across the recently identified Polaris fault (Hunter et al., 2009) near Truckee, California. The type-section site for the Polaris fault is located 6.5 km east of Truckee where progressive right-lateral displacement of middle to late Pleistocene deposits is evident. Glacial outwash deposits, aggraded during the Tioga glaciation, form a flat lying ‘fill’ terrace on both the north and south sides of the modern Truckee River. During the Tioga deglaciation melt water incised into the terrace producing fluvial scarps or terrace risers (Birkeland, 1964). Subsequently, the terrace risers on both banks have been right-laterally offset by the Polaris fault. By using T-LiDAR on an elevated tripod (4.25 m high), we collected 3D high-resolution (thousands of points per square meter; ± 4 mm) point-cloud imagery of the offset terrace risers. Vegetation was removed from the data using commercial software, and large protruding boulders were manually deleted to generate a bare-earth point-cloud dataset with an average data density of over 240 points per square meter. From the bare-earth point cloud we mathematically reconstructed a pristine terrace/scarp morphology on both sides of the fault, defined coupled sets of piercing points, and extracted a corresponding displacement vector. First, the Polaris fault was approximated as a vertical plane that bisects the offset terrace risers, as well as bisecting linear swales and tectonic depressions in the outwash terrace. Then, piercing points to the vertical fault plane were constructed from the geometry of the geomorphic elements on either side of the fault. On each side of the fault, the best-fit modeled outwash plane is projected laterally and the best-fit modeled terrace riser projected upward to a virtual intersection in space, creating a vector. These constructed vectors were projected to intersection with the fault plane, defining statistically significant piercing points. The distance between the coupled set of piercing points, within the plane of the fault, is the cumulative displacement vector. To assess the variability of the modeled geomorphic surfaces, including surface roughness and nonlinearity, we generated a suite of displacement models by systematically incorporating larger areas of the model domain symmetrically about the fault. Preliminary results of 10 models yield an average cumulative displacement of 5.6 m (1 Std Dev = 0.31 m). As previously described, Tioga deglaciation melt water incised into the outwash terrace leaving terrace risers that were subsequently offset by the Polaris fault. Therefore, the age of the Tioga outwash terrace represents a maximum limiting age of the tectonic displacement. Using regional age constraints of 15 to 13 kya for the Tioga outwash terrace (Benson et al., 1990; Clark and Gillespie, 1997; James et al., 2002) and the above model results, we estimate a preliminary minimum fault slip rate of 0.40 ± 0.05 mm/yr for the Polaris type-section site.

Estimating under-five mortality in space and time in a developing world context.

PubMed

Wakefield, Jon; Fuglstad, Geir-Arne; Riebler, Andrea; Godwin, Jessica; Wilson, Katie; Clark, Samuel J

2018-01-01

Accurate estimates of the under-five mortality rate in a developing world context are a key barometer of the health of a nation. This paper describes a new model to analyze survey data on mortality in this context. We are interested in both spatial and temporal description, that is wishing to estimate under-five mortality rate across regions and years and to investigate the association between the under-five mortality rate and spatially varying covariate surfaces. We illustrate the methodology by producing yearly estimates for subnational areas in Kenya over the period 1980-2014 using data from the Demographic and Health Surveys, which use stratified cluster sampling. We use a binomial likelihood with fixed effects for the urban/rural strata and random effects for the clustering to account for the complex survey design. Smoothing is carried out using Bayesian hierarchical models with continuous spatial and temporally discrete components. A key component of the model is an offset to adjust for bias due to the effects of HIV epidemics. Substantively, there has been a sharp decline in Kenya in the under-five mortality rate in the period 1980-2014, but large variability in estimated subnational rates remains. A priority for future research is understanding this variability. In exploratory work, we examine whether a variety of spatial covariate surfaces can explain the variability in under-five mortality rate. Temperature, precipitation, a measure of malaria infection prevalence, and a measure of nearness to cities were candidates for inclusion in the covariate model, but the interplay between space, time, and covariates is complex.

Multi-scale characterization of dissolution structures and porosity distribution in the upper part of the Biscayne aquifer using ground penetrating radar (GPR)

NASA Astrophysics Data System (ADS)

Mount, Gregory J.

The karst Biscayne aquifer is characterized by a heterogeneous spatial arrangement of porosity, making hydrogeological characterization difficult. In this dissertation, I investigate the use of ground penetrating radar (GPR), for understanding the spatial distribution of porosity variability in the Miami Limestone presented as a compilation of studies where scale of measurement is progressively increased to account for varying dimensions of dissolution features. In Chapter 2, GPR in zero offset acquisition mode is used to investigate the 2-D distribution of porosity and dielectric permittivity in a block of Miami Limestone at the laboratory scale (< 1.0 m). Petrophysical models based on fully saturated and unsaturated water conditions are used to estimate porosity and solid dielectric permittivity of the limestone. Results show a good correspondence between analytical and GPR-based porosity estimates and show variability between 22.0-66.0 %. In Chapter 3, GPR in common offset and common midpoint acquisition mode are used to estimate bulk porosity of the unsaturated Miami Limestone at the field scale (10.0-100.0 m). Estimates of porosity are based on the assumption that the directly measured water table reflector is flat and that any deviation is attributed to changes in velocity due to porosity variability. Results show sharp changes in porosity ranging between 33.2-60.9 % attributed to dissolution areas. In Chapter 4, GPR in common offset mode is used to characterize porosity variability in the saturated Biscayne aquifer at 100-1000 m field scales. The presence of numerous diffraction hyperbolae are used to estimate electromagnetic wave velocity and asses both horizontal and vertical changes in porosity after application of a petrophysical model. Results show porosity variability between 23.0-41.0 % and confirm the presence of isolated areas that could serve as enhanced infiltration or recharge. This research allows for the identification and delineation areas of macroporosity areas at 0.01 m lateral resolution and shows variability of porosity at different scales, reaching 37.0 % within 1.3 m, associated with areas of enhanced dissolution. Such improved resolution of porosity estimates can benefit water management efforts and transport modelling and help to better understand small scale relationships between ground water and surface water interactions.

The Width of a CME and the Source of the Driving Magnetic Explosion

NASA Technical Reports Server (NTRS)

Moore, R. L.; Sterling, A. C.; Suess, S. T.

2007-01-01

We show that the strength of the magnetic field in the area covered by the flare arcade following a CME-producing ejective solar eruption can be estimated from the final angular width of the CME in the outer corona and the final angular width of the flare arcade. We assume (1) the flux-rope plasmoid ejected from the flare site becomes the interior of the CME plasmoid, (2) in the outer corona the CME is roughly a "spherical plasmoid with legs" shaped like a light bulb, and (3) beyond some height in or below the outer corona the CME plasmoid is in lateral pressure balance with the surrounding magnetic field. The strength of the nearly radial magnetic field in the outer corona is estimated from the radial component of the interplanetary magnetic field measured by Ulysses. We apply this model to three well-observed CMEs that exploded from flare regions of extremely different size and magnetic setting. In each event, the estimated source-region field strength is appropriate for the magnetic setting of the flare. This agreement indicates via the model that CMEs (1) are propelled by the magnetic field of the CME plasmoid pushing against the surrounding magnetic field, and (2) can explode from flare regions that are laterally far offset from the radial path of the CME in the outer corona.

Residential building codes, affordability, and health protection: a risk-tradeoff approach.

PubMed

Hammitt, J K; Belsky, E S; Levy, J I; Graham, J D

1999-12-01

Residential building codes intended to promote health and safety may produce unintended countervailing risks by adding to the cost of construction. Higher construction costs increase the price of new homes and may increase health and safety risks through "income" and "stock" effects. The income effect arises because households that purchase a new home have less income remaining for spending on other goods that contribute to health and safety. The stock effect arises because suppression of new-home construction leads to slower replacement of less safe housing units. These countervailing risks are not presently considered in code debates. We demonstrate the feasibility of estimating the approximate magnitude of countervailing risks by combining the income effect with three relatively well understood and significant home-health risks. We estimate that a code change that increases the nationwide cost of constructing and maintaining homes by $150 (0.1% of the average cost to build a single-family home) would induce offsetting risks yielding between 2 and 60 premature fatalities or, including morbidity effects, between 20 and 800 lost quality-adjusted life years (both discounted at 3%) each year the code provision remains in effect. To provide a net health benefit, the code change would need to reduce risk by at least this amount. Future research should refine these estimates, incorporate quantitative uncertainty analysis, and apply a full risk-tradeoff approach to real-world case studies of proposed code changes.

Time synchronization of new-generation BDS satellites using inter-satellite link measurements

NASA Astrophysics Data System (ADS)

Pan, Junyang; Hu, Xiaogong; Zhou, Shanshi; Tang, Chengpan; Guo, Rui; Zhu, Lingfeng; Tang, Guifeng; Hu, Guangming

2018-01-01

Autonomous satellite navigation is based on the ability of a Global Navigation Satellite System (GNSS), such as Beidou, to estimate orbits and clock parameters onboard satellites using Inter-Satellite Link (ISL) measurements instead of tracking data from a ground monitoring network. This paper focuses on the time synchronization of new-generation Beidou Navigation Satellite System (BDS) satellites equipped with an ISL payload. Two modes of Ka-band ISL measurements, Time Division Multiple Access (TDMA) mode and the continuous link mode, were used onboard these BDS satellites. Using a mathematical formulation for each measurement mode along with a derivation of the satellite clock offsets, geometric ranges from the dual one-way measurements were introduced. Then, pseudoranges and clock offsets were evaluated for the new-generation BDS satellites. The evaluation shows that the ranging accuracies of TDMA ISL and the continuous link are approximately 4 cm and 1 cm (root mean square, RMS), respectively. Both lead to ISL clock offset residuals of less than 0.3 ns (RMS). For further validation, time synchronization between these satellites to a ground control station keeping the systematic time in BDT was conducted using L-band Two-way Satellite Time Frequency Transfer (TWSTFT). System errors in the ISL measurements were calibrated by comparing the derived clock offsets with the TWSTFT. The standard deviations of the estimated ISL system errors are less than 0.3 ns, and the calibrated ISL clock parameters are consistent with that of the L-band TWSTFT. For the regional BDS network, the addition of ISL measurements for medium orbit (MEO) BDS satellites increased the clock tracking coverage by more than 40% for each orbital revolution. As a result, the clock predicting error for the satellite M1S was improved from 3.59 to 0.86 ns (RMS), and the predicting error of the satellite M2S was improved from 1.94 to 0.57 ns (RMS), which is a significant improvement by a factor of 3-4.

Commercial possibilities for stranded conventional gas from Alaska's North Slope

USGS Publications Warehouse

Attanasi, E.D.; Freeman, P.A.

2014-01-01

Stranded gas resources are defined for this study as gas resources in discrete accumulations that are not currently commercially producible, or producible at full potential, for either physical or economic reasons. Approximately 35 trillion cubic feet (TCF) of stranded gas was identified on Alaska’s North Slope. The commercialization of this resource requires facilities to transport gas to markets where sales revenue will be sufficient to offset the cost of constructing and operating a gas delivery system. With the advent of the shale gas revolution, plans for a gas pipeline to the conterminous US have been shelved (at least temporarily) and the State and resource owners are considering a liquefied natural gas (LNG) export project that targets Asian markets. This paper focuses on competitive conditions for Asian gas import markets by estimating delivered costs of competing supplies from central Asia, Russia, Indonesia, Malaysia, and Australia in the context of a range of import gas demand projections for the period from 2020 to 2040. These suppliers’ costs are based on the cost of developing, producing, and delivering to markets tranches of the nearly 600 TCF of recoverable gas from their own conventional stranded gas fields. The results of these analyses imply that Alaska’s gas exports to Asia will likely encounter substantial competitive challenges. The sustainability of Asia’s oil-indexed LNG pricing is also discussed in light of a potentially intense level of competition.

High-Performance Clock Synchronization Algorithms for Distributed Wireless Airborne Computer Networks with Applications to Localization and Tracking of Targets

DTIC Science & Technology

2010-06-01

GMKPF represents a better and more flexible alternative to the Gaussian Maximum Likelihood (GML), and Exponential Maximum Likelihood ( EML ...accurate results relative to GML and EML when the network delays are modeled in terms of a single non-Gaussian/non-exponential distribution or as a...to the Gaussian Maximum Likelihood (GML), and Exponential Maximum Likelihood ( EML ) estimators for clock offset estimation in non-Gaussian or non

Two Propositions on the Application of Point Elasticities to Finite Price Changes.

ERIC Educational Resources Information Center

Daskin, Alan J.

1992-01-01

Considers counterintuitive propositions about using point elasticities to estimate quantity changes in response to price changes. Suggests that elasticity increases with price along a linear demand curve, but falling quantity demand offsets it. Argues that point elasticity with finite percentage change in price only approximates percentage change…

Resolution convergence in cosmological hydrodynamical simulations using adaptive mesh refinement

NASA Astrophysics Data System (ADS)

Snaith, Owain N.; Park, Changbom; Kim, Juhan; Rosdahl, Joakim

2018-06-01

We have explored the evolution of gas distributions from cosmological simulations carried out using the RAMSES adaptive mesh refinement (AMR) code, to explore the effects of resolution on cosmological hydrodynamical simulations. It is vital to understand the effect of both the resolution of initial conditions (ICs) and the final resolution of the simulation. Lower initial resolution simulations tend to produce smaller numbers of low-mass structures. This will strongly affect the assembly history of objects, and has the same effect of simulating different cosmologies. The resolution of ICs is an important factor in simulations, even with a fixed maximum spatial resolution. The power spectrum of gas in simulations using AMR diverges strongly from the fixed grid approach - with more power on small scales in the AMR simulations - even at fixed physical resolution and also produces offsets in the star formation at specific epochs. This is because before certain times the upper grid levels are held back to maintain approximately fixed physical resolution, and to mimic the natural evolution of dark matter only simulations. Although the impact of hold-back falls with increasing spatial and IC resolutions, the offsets in the star formation remain down to a spatial resolution of 1 kpc. These offsets are of the order of 10-20 per cent, which is below the uncertainty in the implemented physics but are expected to affect the detailed properties of galaxies. We have implemented a new grid-hold-back approach to minimize the impact of hold-back on the star formation rate.

THE LOCATIONS OF SHORT GAMMA-RAY BURSTS AS EVIDENCE FOR COMPACT OBJECT BINARY PROGENITORS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fong, W.; Berger, E.

2013-10-10

We present a detailed investigation of Hubble Space Telescope rest-frame UV/optical observations of 22 short gamma-ray burst (GRB) host galaxies and sub-galactic environments. Utilizing the high angular resolution and depth of HST we characterize the host galaxy morphologies, measure precise projected physical and host-normalized offsets between the bursts and host centers, and calculate the locations of the bursts with respect to their host light distributions (rest-frame UV and optical). We calculate a median short GRB projected physical offset of 4.5 kpc, about 3.5 times larger than that for long GRBs, and find that ≈25% of short GRBs have offsets ofmore » ∼> 10 kpc. When compared to their host sizes, the median offset is 1.5 half-light radii (r{sub e} ), about 1.5 times larger than the values for long GRBs, core-collapse supernovae, and Type Ia supernovae. In addition, ≈20% of short GRBs having offsets of ∼> 5r{sub e} , and only ≈25% are located within 1r{sub e} . We further find that short GRBs severely under-represent their hosts' rest-frame optical and UV light, with ≈30%-45% of the bursts located in regions of their host galaxies that have no detectable stellar light, and ≈55% in the regions with no UV light. Therefore, short GRBs do not occur in regions of star formation or even stellar mass. This demonstrates that the progenitor systems of short GRBs must migrate from their birth sites to their eventual explosion sites, a signature of kicks in compact object binary systems. Utilizing the full sample of offsets, we estimate natal kick velocities of ≈20-140 km s{sup –1}. These independent lines of evidence provide the strongest support to date that short GRBs result from the merger of compact object binaries (NS-NS/NS-BH)« less

Investigation of practical initial attenuation image estimates in TOF-MLAA reconstruction for PET/MR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Ju-Chieh, E-mail: chengjuchieh@gmail.com; Y

Purpose: Time-of-flight joint attenuation and activity positron emission tomography reconstruction requires additional calibration (scale factors) or constraints during or post-reconstruction to produce a quantitative μ-map. In this work, the impact of various initializations of the joint reconstruction was investigated, and the initial average mu-value (IAM) method was introduced such that the forward-projection of the initial μ-map is already very close to that of the reference μ-map, thus reducing/minimizing the offset (scale factor) during the early iterations of the joint reconstruction. Consequently, the accuracy and efficiency of unconstrained joint reconstruction such as time-of-flight maximum likelihood estimation of attenuation and activity (TOF-MLAA)more » can be improved by the proposed IAM method. Methods: 2D simulations of brain and chest were used to evaluate TOF-MLAA with various initial estimates which include the object filled with water uniformly (conventional initial estimate), bone uniformly, the average μ-value uniformly (IAM magnitude initialization method), and the perfect spatial μ-distribution but with a wrong magnitude (initialization in terms of distribution). 3D GATE simulation was also performed for the chest phantom under a typical clinical scanning condition, and the simulated data were reconstructed with a fully corrected list-mode TOF-MLAA algorithm with various initial estimates. The accuracy of the average μ-values within the brain, chest, and abdomen regions obtained from the MR derived μ-maps was also evaluated using computed tomography μ-maps as the gold-standard. Results: The estimated μ-map with the initialization in terms of magnitude (i.e., average μ-value) was observed to reach the reference more quickly and naturally as compared to all other cases. Both 2D and 3D GATE simulations produced similar results, and it was observed that the proposed IAM approach can produce quantitative μ-map/emission when the corrections for physical effects such as scatter and randoms were included. The average μ-value obtained from MR derived μ-map was accurate within 5% with corrections for bone, fat, and uniform lungs. Conclusions: The proposed IAM-TOF-MLAA can produce quantitative μ-map without any calibration provided that there are sufficient counts in the measured data. For low count data, noise reduction and additional regularization/rescaling techniques need to be applied and investigated. The average μ-value within the object is prior information which can be extracted from MR and patient database, and it is feasible to obtain accurate average μ-value using MR derived μ-map with corrections as demonstrated in this work.« less

Teaching through Trade Books: Humans and the Earth

ERIC Educational Resources Information Center

Royce, Christine Anne

2016-01-01

This column includes activities inspired by children's literature. Elementary students are beginning to understand the Earth's natural processes and humans' impact on the Earth. Humans need the natural resources that the Earth produces, use these resources to develop civilizations, and make decisions to offset the damage they cause, as well as…

Beam based alignment and its relevance in Indus-2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jena, Saroj Kumar; Husain, Riyasat; Gandhi, M. L.

2015-09-15

Initially in the Indus-2 storage ring, the closed orbit distortion (COD) could be best corrected to 1.3 mm rms in the horizontal and 0.43 mm rms in the vertical plane. The strength of the corrector magnets required high values for COD correction. This revealed that offsets in COD readout by the beam position monitors (BPMs) played a role in not achieving a rms COD lower than the above value. Thus, the offset between the electrical center of BPMs and the magnetic center of the nearest quadrupole magnet could be estimated using the beam based alignment (BBA) method. It prefers thatmore » the quadrupole magnet is able to be controlled individually and active shunt power supply (ASPS) system was designed for this purpose that works efficiently. This paper describes the methodology of BBA, topology of ASPS and its performance, and COD minimization using the measured BPM offsets. After BBA, the COD could be reduced to 0.45 mm rms and 0.2 mm rms in horizontal and vertical planes, respectively.« less

Qualitative analysis of MTEM response using instantaneous attributes

NASA Astrophysics Data System (ADS)

Fayemi, Olalekan; Di, Qingyun

2017-11-01

This paper introduces new technique for qualitative analysis of multi-transient electromagnetic (MTEM) earth impulse response over complex geological structures. Instantaneous phase and frequency attributes were used in place of the conventional common offset section for improved qualitative interpretation of MTEM data by obtaining more detailed information from the earth impulse response. The instantaneous attributes were used to describe the lateral variation in subsurface resistivity and the visible geological structure with respect to given offsets. Instantaneous phase attribute was obtained by converting the impulse response into a complex form using the Hilbert transform. Conversely, the polynomial phase difference (PPD) estimator was favored over the center finite difference (CFD) approximation method in calculating the instantaneous frequency attribute because it is computationally efficient and has the ability to give a smooth variation of the instantaneous frequency over a common offset section. The observed results from the instantaneous attributes were in good agreement with both the subsurface model used and the apparent resistivity section obtained from the MTEM earth impulse response. Hence, this study confirms the capability of both instantaneous phase and frequency attributes as highly effective tools for MTEM qualitative analysis.

FBMC receiver for multi-user asynchronous transmission on fragmented spectrum

NASA Astrophysics Data System (ADS)

Doré, Jean-Baptiste; Berg, Vincent; Cassiau, Nicolas; Kténas, Dimitri

2014-12-01

Relaxed synchronization and access to fragmented spectrum are considered for future generations of wireless networks. Frequency division multiple access for filter bank multicarrier (FBMC) modulation provides promising performance without strict synchronization requirements contrary to conventional orthogonal frequency division multiplexing (OFDM). The architecture of a FBMC receiver suitable for this scenario is considered. Carrier frequency offset (CFO) compensation is combined with intercarrier interference (ICI) cancellation and performs well under very large frequency offsets. Channel estimation and interpolation had to be adapted and proved effective even for heavily fragmented spectrum usage. Channel equalization can sustain large delay spread. Because all the receiver baseband signal processing functionalities are proposed in the frequency domain, the overall architecture is suitable for multiuser asynchronous transmission on fragmented spectrum.

A New Offset Debris Ring around a Nearby Star Observed with the HST/STIS

NASA Technical Reports Server (NTRS)

Krist, John; Stapelfeldt, Karl; Bryden, Geoffrey

2011-01-01

We are conducting an HST/STIS coronagraphic imaging study of nearby stars that have Spitzer-measured infrared excesses indicating that they are surrounded by debris disks. Around one of the stars we have imaged a debris ring with a sharp inner edge and extending from about 165 AU to 250 AU. The ring center is offset from the star by -8 AU with a visually estimated intrinsic ellipticity of e-0.1 , suggestive of gravitational perturbation of the disk by a planet, like the Fomalhaut disk. Assuming a neutral disk color, the mean surface brightness of V=22.3 mag/square arcsec makes this the second faintest disk yet imaged in scattered light, second to HD 207129.

Effects of rolling friction on a spinning coin or disk

NASA Astrophysics Data System (ADS)

Cross, Rod

2018-05-01

Experimental and theoretical results are presented concerning the motion of a spinning disk on a horizontal surface. The disk precesses about a vertical axis while falling either quickly or slowly onto the surface depending on the coefficient of rolling friction. The rate of fall also depends on the offset distance, in the rolling direction, between the centre of mass and the line of action of the normal reaction force. Euler’s angular momentum equations are solved to obtain estimates of both the coefficient of friction and the offset distance for a 50.6 mm diameter brass disk spinning on three different surfaces. The fall times varied from about 3 s on P800 emery paper to about 30 s on glass.

The effect of frictional torque and bending moment on corrosion at the taper interface : an in vitro study.

PubMed

Panagiotidou, A; Meswania, J; Osman, K; Bolland, B; Latham, J; Skinner, J; Haddad, F S; Hart, A; Blunn, G

2015-04-01

The aim of this study was to assess the effect of frictional torque and bending moment on fretting corrosion at the taper interface of a modular femoral component and to investigate whether different combinations of material also had an effect. The combinations we examined were 1) cobalt-chromium (CoCr) heads on CoCr stems 2) CoCr heads on titanium alloy (Ti) stems and 3) ceramic heads on CoCr stems. In test 1 increasing torque was imposed by offsetting the stem in the anteroposterior plane in increments of 0 mm, 4 mm, 6 mm and 8 mm when the torque generated was equivalent to 0 Nm, 9 Nm, 14 Nm and 18 Nm. In test 2 we investigated the effect of increasing the bending moment by offsetting the application of axial load from the midline in the mediolateral plane. Increments of offset equivalent to head + 0 mm, head + 7 mm and head + 14 mm were used. Significantly higher currents and amplitudes were seen with increasing torque for all combinations of material. However, Ti stems showed the highest corrosion currents. Increased bending moments associated with using larger offset heads produced more corrosion: Ti stems generally performed worse than CoCr stems. Using ceramic heads did not prevent corrosion, but reduced it significantly in all loading configurations. ©2015 The British Editorial Society of Bone & Joint Surgery.

Interactions of a co-rotating vortex pair at multiple offsets

NASA Astrophysics Data System (ADS)

Forster, Kyle J.; Barber, Tracie J.; Diasinos, Sammy; Doig, Graham

2017-05-01

Two NACA0012 vanes at various lateral offsets were investigated by wind tunnel testing to observe the interactions between the streamwise vortices. The vanes were separated by nine chord lengths in the streamwise direction to allow the upstream vortex to impact on the downstream geometry. These vanes were evaluated at an angle of incidence of 8° and a Reynolds number of 7 ×104 using particle image velocimetry. A helical motion of the vortices was observed, with rotational rate increasing as the offset was reduced to the point of vortex merging. Downstream meandering of the weaker vortex was found to increase in magnitude near the point of vortex merging. The merging process occurred more rapidly when the upstream vortex was passed on the pressure side of the vane, with the downstream vortex being produced with less circulation and consequently merging into the upstream vortex. The merging distance was found to be statistical rather than deterministic quantity, indicating that the meandering of the vortices affected their separations and energies. This resulted in a fluctuation of the merging location. A loss of circulation associated with the merging process was identified, with the process of achieving vortex circularity causing vorticity diffusion, however all merged cases maintained higher circulation than a single vortex condition. The presence of the upstream vortex was found to reduce the strength of the downstream vortex in all offsets evaluated.

Similar star formation rate and metallicity variability time-scales drive the fundamental metallicity relation

NASA Astrophysics Data System (ADS)

Torrey, Paul; Vogelsberger, Mark; Hernquist, Lars; McKinnon, Ryan; Marinacci, Federico; Simcoe, Robert A.; Springel, Volker; Pillepich, Annalisa; Naiman, Jill; Pakmor, Rüdiger; Weinberger, Rainer; Nelson, Dylan; Genel, Shy

2018-06-01

The fundamental metallicity relation (FMR) is a postulated correlation between galaxy stellar mass, star formation rate (SFR), and gas-phase metallicity. At its core, this relation posits that offsets from the mass-metallicity relation (MZR) at a fixed stellar mass are correlated with galactic SFR. In this Letter, we use hydrodynamical simulations to quantify the time-scales over which populations of galaxies oscillate about the average SFR and metallicity values at fixed stellar mass. We find that Illustris and IllustrisTNG predict that galaxy offsets from the star formation main sequence and MZR oscillate over similar time-scales, are often anticorrelated in their evolution, evolve with the halo dynamical time, and produce a pronounced FMR. Our models indicate that galaxies oscillate about equilibrium SFR and metallicity values - set by the galaxy's stellar mass - and that SFR and metallicity offsets evolve in an anticorrelated fashion. This anticorrelated variability of the metallicity and SFR offsets drives the existence of the FMR in our models. In contrast to Illustris and IllustrisTNG, we speculate that the SFR and metallicity evolution tracks may become decoupled in galaxy formation models dominated by feedback-driven globally bursty SFR histories, which could weaken the FMR residual correlation strength. This opens the possibility of discriminating between bursty and non-bursty feedback models based on the strength and persistence of the FMR - especially at high redshift.

Composition dependent band offsets of ZnO and its ternary alloys

NASA Astrophysics Data System (ADS)

Yin, Haitao; Chen, Junli; Wang, Yin; Wang, Jian; Guo, Hong

2017-01-01

We report the calculated fundamental band gaps of wurtzite ternary alloys Zn1-xMxO (M = Mg, Cd) and the band offsets of the ZnO/Zn1-xMxO heterojunctions, these II-VI materials are important for electronics and optoelectronics. Our calculation is based on density functional theory within the linear muffin-tin orbital (LMTO) approach where the modified Becke-Johnson (MBJ) semi-local exchange is used to accurately produce the band gaps, and the coherent potential approximation (CPA) is applied to deal with configurational average for the ternary alloys. The combined LMTO-MBJ-CPA approach allows one to simultaneously determine both the conduction band and valence band offsets of the heterojunctions. The calculated band gap data of the ZnO alloys scale as Eg = 3.35 + 2.33x and Eg = 3.36 - 2.33x + 1.77x2 for Zn1-xMgxO and Zn1-xCdxO, respectively, where x being the impurity concentration. These scaling as well as the composition dependent band offsets are quantitatively compared to the available experimental data. The capability of predicting the band parameters and band alignments of ZnO and its ternary alloys with the LMTO-CPA-MBJ approach indicate the promising application of this method in the design of emerging electronics and optoelectronics.

FEL system with homogeneous average output

DOEpatents

Douglas, David R.; Legg, Robert; Whitney, R. Roy; Neil, George; Powers, Thomas Joseph

2018-01-16

A method of varying the output of a free electron laser (FEL) on very short time scales to produce a slightly broader, but smooth, time-averaged wavelength spectrum. The method includes injecting into an accelerator a sequence of bunch trains at phase offsets from crest. Accelerating the particles to full energy to result in distinct and independently controlled, by the choice of phase offset, phase-energy correlations or chirps on each bunch train. The earlier trains will be more strongly chirped, the later trains less chirped. For an energy recovered linac (ERL), the beam may be recirculated using a transport system with linear and nonlinear momentum compactions M.sub.56, which are selected to compress all three bunch trains at the FEL with higher order terms managed.

Band alignment at the Cu2ZnSn(SxSe1-x)4/CdS interface

NASA Astrophysics Data System (ADS)

Haight, Richard; Barkhouse, Aaron; Gunawan, Oki; Shin, Byungha; Copel, Matt; Hopstaken, Marinus; Mitzi, David B.

2011-06-01

Energy band alignments between CdS and Cu2ZnSn(SxSe1-x)4 (CZTSSe) grown via solution-based and vacuum-based deposition routes were studied as a function of the [S]/[S+Se] ratio with femtosecond laser ultraviolet photoelectron spectroscopy, photoluminescence, medium energy ion scattering, and secondary ion mass spectrometry. Band bending in the underlying CZTSSe layer was measured via pump/probe photovoltage shifts of the photoelectron spectra and offsets were determined with photoemission under flat band conditions. Increasing the S content of the CZTSSe films produces a valence edge shift to higher binding energy and increases the CZTSSe band gap. In all cases, the CdS conduction band offsets were spikes.

Greater transportation energy and GHG offsets from bioelectricity than ethanol.

PubMed

Campbell, J E; Lobell, D B; Field, C B

2009-05-22

The quantity of land available to grow biofuel crops without affecting food prices or greenhouse gas (GHG) emissions from land conversion is limited. Therefore, bioenergy should maximize land-use efficiency when addressing transportation and climate change goals. Biomass could power either internal combustion or electric vehicles, but the relative land-use efficiency of these two energy pathways is not well quantified. Here, we show that bioelectricity outperforms ethanol across a range of feedstocks, conversion technologies, and vehicle classes. Bioelectricity produces an average of 81% more transportation kilometers and 108% more emissions offsets per unit area of cropland than does cellulosic ethanol. These results suggest that alternative bioenergy pathways have large differences in how efficiently they use the available land to achieve transportation and climate goals.

Digital computer program DF1758 fully coupled natural frequencies and mode shapes of a helicopter rotor blade

NASA Technical Reports Server (NTRS)

Bennett, R. L.

1975-01-01

The analytical techniques and computer program developed in the fully-coupled rotor vibration study are described. The rotor blade natural frequency and mode shape analysis was implemented in a digital computer program designated DF1758. The program computes collective, cyclic, and scissor modes for a single blade within a specified range of frequency for specified values of rotor RPM and collective angle. The analysis includes effects of blade twist, cg offset from reference axis, and shear center offset from reference axis. Coupled inplane, out-of-plane, and torsional vibrations are considered. Normalized displacements, shear forces and moments may be printed out and Calcomp plots of natural frequencies as a function of rotor RPM may be produced.

Stretchable polymer-based electronic device

DOEpatents

Maghribi, Mariam N [Livermore, CA; Krulevitch, Peter A [Pleasanton, CA; Davidson, James Courtney [Livermore, CA; Wilson, Thomas S [Castro Valley, CA; Hamilton, Julie K [Tracy, CA; Benett, William J [Livermore, CA; Tovar, Armando R [San Antonio, TX

2008-02-26

A stretchable electronic circuit or electronic device and a polymer-based process to produce a circuit or electronic device containing a stretchable conducting circuit. The stretchable electronic apparatus has a central longitudinal axis and the apparatus is stretchable in a longitudinal direction generally aligned with the central longitudinal axis. The apparatus comprises a stretchable polymer body and at least one circuit line operatively connected to the stretchable polymer body. The circuit line extends in the longitudinal direction and has a longitudinal component that extends in the longitudinal direction and has an offset component that is at an angle to the longitudinal direction. The longitudinal component and the offset component allow the apparatus to stretch in the longitudinal direction while maintaining the integrity of the circuit line.

Serpentine and corduroy circuits to enhance the stretchability of a stretchable electronic device

DOEpatents

Maghribi, Mariam N [Livermore, CA; Krulevitch, Peter A [Pleasanton, CA; Wilson, Thomas S [Castro Valley, CA; Hamilton, Julie K. , Park; Christina, [Cambridge, MA

2007-09-04

A stretchable electronic apparatus and method of producing the apparatus. The apparatus has a central longitudinal axis and the apparatus is stretchable in a longitudinal direction generally aligned with the central longitudinal axis. The apparatus comprises a stretchable polymer body, and at least one circuit line operatively connected to the stretchable polymer body, the at least one circuit line extending in the longitudinal direction and having a longitudinal component that extends in the longitudinal direction and having an offset component that is at an angle to the longitudinal direction, the longitudinal component and the offset component allowing the apparatus to stretch in the longitudinal direction while maintaining the integrity of the at least one circuit line.

Serpentine and corduroy circuits to enhance the stretchablity of a stretchable electronic device

DOEpatents

Maghribi, Mariam N [Livermore, CA; Krulevitch, Peter A [Pleasanton, CA; Wilson, Thomas S [Castro Valley, CA; Hamilton, Julie K [Tracy, CA; Park, Christina [Cambridge, MA

2011-01-18

A stretchable electronic apparatus and method of producing the apparatus. The apparatus has a central longitudinal axis and the apparatus is stretchable in a longitudinal direction generally aligned with the central longitudinal axis. The apparatus comprises a stretchable polymer body, and at least one circuit line operatively connected to the stretchable polymer body, the at least one circuit line extending in the longitudinal direction and having a longitudinal component that extends in the longitudinal direction and having an offset component that is at an angle to the longitudinal direction, the longitudinal component and the offset component allowing the apparatus to stretch in the longitudinal direction while maintaining the integrity of the at least one circuit line.

Mixing in Gas Phase Turbulent Jets

DTIC Science & Technology

1988-01-01

jet centerline with about 4 ZD per line 81 5-14 Comparison of flame lengths reported by Dahm et al. (1984) with those estimated from the measured PDFs...the flame length studies of Weddell (1952) and Dahm et al. (1984) . Their work points to Re 0 M 3,000 as the threshold where the degree of molecular...increased abundance at high C/C, however, offsets - 84 - part of the 8% loss in mean concentration when a flame length is estimated from the measured PDF

Determination of HART I Blade Structural Properties by Laboratory Testing

NASA Technical Reports Server (NTRS)

Jung, Sung N.; Lau, Benton H.

2012-01-01

The structural properties of higher harmonic Aeroacoustic Rotor Test (HART I) blades were measured using the original set of blades tested in the German-dutch wind tunnel (DNW) in 1994. the measurements include bending and torsion stiffness, geometric offsets, and mass and inertia properties of the blade. the measured properties were compared to the estimated values obtained initially from the blade manufacturer. The previously estimated blade properties showed consistently higher stiffness, up to 30 percent for the flap bending in the blade inboard root section.

Incremental Holocene slip rates from the Hope fault at Hossack Station, Marlborough fault zone, South Island, New Zealand

NASA Astrophysics Data System (ADS)

Hatem, A. E.; Dolan, J. F.; Langridge, R.; Zinke, R. W.; McGuire, C. P.; Rhodes, E. J.; Van Dissen, R. J.

2015-12-01

The Marlborough fault system, which links the Alpine fault with the Hikurangi subduction zone within the complex Australian-Pacific plate boundary zone, partitions strain between the Wairau, Awatere, Clarence and Hope faults. Previous best estimates of dextral strike-slip along the Hope fault are ≤ ~23 mm/yr± 4 mm/year. Those rates, however, are poorly constrained and could be improved using better age determinations in conjunction with measurements of fault offsets using high-resolution imagery. In this study, we use airborne lidar- and field-based mapping together with the subsurface geometry of offset channels at the Hossack site 12 km ESE of Hanmer Springs to more precisely determine stream offsets that were previously identified by McMorran (1991). Specifically, we measured fault offsets of ~10m, ~75 m, and ~195m. Together with 65 radiocarbon ages on charcoal, peat, and wood and 25 pending post-IR50-IRSL225 luminescence ages from the channel deposits, these offsets yield three different fault slip rates for the early Holocene, the late Holocene, and the past ca. 500-1,000 years. Using the large number of age determinations, we document in detail the timing of initiation and abandonment of each channel, enhancing the geomorphic interpretation at the Hossack site as channels deform over many earthquake cycles. Our preliminary incremental slip rate results from the Hossack site may indicate temporally variable strain release along the Hope fault. This study is part of a broader effort aimed at determining incremental slip rates and paleo-earthquake ages and displacements from all four main Marlborough faults. Collectively, these data will allow us to determine how the four main Marlborough faults have work together during Holocene-late Pleistocene to accommodate plate-boundary deformation in time and space.

Basin geometry and cumulative offsets in the Eastern Transverse Ranges, southern California: Implications for transrotational deformation along the San Andreas fault system

USGS Publications Warehouse

Langenheim, V.E.; Powell, R.E.

2009-01-01

The Eastern Transverse Ranges, adjacent to and southeast of the big left bend of the San Andreas fault, southern California, form a crustal block that has rotated clockwise in response to dextral shear within the San Andreas system. Previous studies have indicated a discrepancy between the measured magnitudes of left slip on through-going east-striking fault zones of the Eastern Transverse Ranges and those predicted by simple geometric models using paleomagnetically determined clockwise rotations of basalts distributed along the faults. To assess the magnitude and source of this discrepancy, we apply new gravity and magnetic data in combination with geologic data to better constrain cumulative fault offsets and to define basin structure for the block between the Pinto Mountain and Chiriaco fault zones. Estimates of offset from using the length of pull-apart basins developed within left-stepping strands of the sinistral faults are consistent with those derived by matching offset magnetic anomalies and bedrock patterns, indicating a cumulative offset of at most ???40 km. The upper limit of displacements constrained by the geophysical and geologic data overlaps with the lower limit of those predicted at the 95% confidence level by models of conservative slip located on margins of rigid rotating blocks and the clockwise rotation of the paleomagnetic vectors. Any discrepancy is likely resolved by internal deformation within the blocks, such as intense deformation adjacent to the San Andreas fault (that can account for the absence of basins there as predicted by rigid-block models) and linkage via subsidiary faults between the main faults. ?? 2009 Geological Society of America.

How recalibration method, pricing, and coding affect DRG weights

PubMed Central

Carter, Grace M.; Rogowski, Jeannette A.

1992-01-01

We compared diagnosis-related group (DRG) weights calculated using the hospital-specific relative-value (HSR V) methodology with those calculated using the standard methodology for each year from 1985 through 1989 and analyzed differences between the two methods in detail for 1989. We provide evidence suggesting that classification error and subsidies of higher weighted cases by lower weighted cases caused compression in the weights used for payment as late as the fifth year of the prospective payment system. However, later weights calculated by the standard method are not compressed because a statistical correlation between high markups and high case-mix indexes offsets the cross-subsidization. HSR V weights from the same files are compressed because this methodology is more sensitive to cross-subsidies. However, both sets of weights produce equally good estimates of hospital-level costs net of those expenses that are paid by outlier payments. The greater compression of the HSR V weights is counterbalanced by the fact that more high-weight cases qualify as outliers. PMID:10127456

Bayesian semi-parametric analysis of Poisson change-point regression models: application to policy making in Cali, Colombia.

PubMed

Park, Taeyoung; Krafty, Robert T; Sánchez, Alvaro I

2012-07-27

A Poisson regression model with an offset assumes a constant baseline rate after accounting for measured covariates, which may lead to biased estimates of coefficients in an inhomogeneous Poisson process. To correctly estimate the effect of time-dependent covariates, we propose a Poisson change-point regression model with an offset that allows a time-varying baseline rate. When the nonconstant pattern of a log baseline rate is modeled with a nonparametric step function, the resulting semi-parametric model involves a model component of varying dimension and thus requires a sophisticated varying-dimensional inference to obtain correct estimates of model parameters of fixed dimension. To fit the proposed varying-dimensional model, we devise a state-of-the-art MCMC-type algorithm based on partial collapse. The proposed model and methods are used to investigate an association between daily homicide rates in Cali, Colombia and policies that restrict the hours during which the legal sale of alcoholic beverages is permitted. While simultaneously identifying the latent changes in the baseline homicide rate which correspond to the incidence of sociopolitical events, we explore the effect of policies governing the sale of alcohol on homicide rates and seek a policy that balances the economic and cultural dependencies on alcohol sales to the health of the public.

Estimation of ion competition via correlated responsivity offset in linear ion trap mass spectrometry analysis: theory and practical use in the analysis of cyanobacterial hepatotoxin microcystin-LR in extracts of food additives.

PubMed

Urban, Jan; Hrouzek, Pavel; Stys, Dalibor; Martens, Harald

2013-01-01

Responsivity is a conversion qualification of a measurement device given by the functional dependence between the input and output quantities. A concentration-response-dependent calibration curve represents the most simple experiment for the measurement of responsivity in mass spectrometry. The cyanobacterial hepatotoxin microcystin-LR content in complex biological matrices of food additives was chosen as a model example of a typical problem. The calibration curves for pure microcystin and its mixtures with extracts of green alga and fish meat were reconstructed from the series of measurement. A novel approach for the quantitative estimation of ion competition in ESI is proposed in this paper. We define the correlated responsivity offset in the intensity values using the approximation of minimal correlation given by the matrix to the target mass values of the analyte. The estimation of the matrix influence enables the approximation of the position of a priori unknown responsivity and was easily evaluated using a simple algorithm. The method itself is directly derived from the basic attributes of the theory of measurements. There is sufficient agreement between the theoretical and experimental values. However, some theoretical issues are discussed to avoid misinterpretations and excessive expectations.

Estimation of Ion Competition via Correlated Responsivity Offset in Linear Ion Trap Mass Spectrometry Analysis: Theory and Practical Use in the Analysis of Cyanobacterial Hepatotoxin Microcystin-LR in Extracts of Food Additives

PubMed Central

Hrouzek, Pavel; Štys, Dalibor; Martens, Harald

2013-01-01

Responsivity is a conversion qualification of a measurement device given by the functional dependence between the input and output quantities. A concentration-response-dependent calibration curve represents the most simple experiment for the measurement of responsivity in mass spectrometry. The cyanobacterial hepatotoxin microcystin-LR content in complex biological matrices of food additives was chosen as a model example of a typical problem. The calibration curves for pure microcystin and its mixtures with extracts of green alga and fish meat were reconstructed from the series of measurement. A novel approach for the quantitative estimation of ion competition in ESI is proposed in this paper. We define the correlated responsivity offset in the intensity values using the approximation of minimal correlation given by the matrix to the target mass values of the analyte. The estimation of the matrix influence enables the approximation of the position of a priori unknown responsivity and was easily evaluated using a simple algorithm. The method itself is directly derived from the basic attributes of the theory of measurements. There is sufficient agreement between the theoretical and experimental values. However, some theoretical issues are discussed to avoid misinterpretations and excessive expectations. PMID:23586036

Mapping soil organic carbon content and composition across Australia to assess vulnerability to climate change

NASA Astrophysics Data System (ADS)

Viscarra Rossel, R. A.

2015-12-01

We can effectively monitor soil condition—and develop sound policies to offset the emissions of greenhouse gases—only with accurate data from which to define baselines. Currently, estimates of soil organic C for countries or continents are either unavailable or largely uncertain because they are derived from sparse data, with large gaps over many areas of the Earth. Here, we derive spatially explicit estimates, and their uncertainty, of the distribution and stock of organic C content and composition in the soil of Australia. The composition of soil organic C may be characterized by chemical separation or physical fractionation based on either particle size or particle density (Skjemstad et al., 2004; Gregorich et al., 2006; Kelleher&Simpson, 2006; Zimmermann et al., 2007). In Australia, for example, Skjemstad et al. (2004) used physical separation of soil samples into 50-2000 and <50-μm particle-size fractions followed by the measurement of char-carbon using solid-state 13C nuclear magnetic resonance (NMR) spectroscopy, giving the three OC pools, particulate organic carbon (POC), humic organic carbon (HOC) and resistant organic carbon (ROC; charcoal or char-carbon). We assembled and harmonized data from several sources to produce the most comprehensive set of data on the current stock of organic C in soil of the continent. Using them, we have produced a fine spatial resolution baseline map of organic C, POC, HOC and ROC at the continental scale. In this presentation I will describe how we made the maps and how we use them to assess the vulnerability of soil organic C to for instance climate change.

Comparative assessment of bone pose estimation using Point Cluster Technique and OpenSim.

PubMed

Lathrop, Rebecca L; Chaudhari, Ajit M W; Siston, Robert A

2011-11-01

Estimating the position of the bones from optical motion capture data is a challenge associated with human movement analysis. Bone pose estimation techniques such as the Point Cluster Technique (PCT) and simulations of movement through software packages such as OpenSim are used to minimize soft tissue artifact and estimate skeletal position; however, using different methods for analysis may produce differing kinematic results which could lead to differences in clinical interpretation such as a misclassification of normal or pathological gait. This study evaluated the differences present in knee joint kinematics as a result of calculating joint angles using various techniques. We calculated knee joint kinematics from experimental gait data using the standard PCT, the least squares approach in OpenSim applied to experimental marker data, and the least squares approach in OpenSim applied to the results of the PCT algorithm. Maximum and resultant RMS differences in knee angles were calculated between all techniques. We observed differences in flexion/extension, varus/valgus, and internal/external rotation angles between all approaches. The largest differences were between the PCT results and all results calculated using OpenSim. The RMS differences averaged nearly 5° for flexion/extension angles with maximum differences exceeding 15°. Average RMS differences were relatively small (< 1.08°) between results calculated within OpenSim, suggesting that the choice of marker weighting is not critical to the results of the least squares inverse kinematics calculations. The largest difference between techniques appeared to be a constant offset between the PCT and all OpenSim results, which may be due to differences in the definition of anatomical reference frames, scaling of musculoskeletal models, and/or placement of virtual markers within OpenSim. Different methods for data analysis can produce largely different kinematic results, which could lead to the misclassification of normal or pathological gait. Improved techniques to allow non-uniform scaling of generic models to more accurately reflect subject-specific bone geometries and anatomical reference frames may reduce differences between bone pose estimation techniques and allow for comparison across gait analysis platforms.

Non-linear mixing effects on mass-47 CO2 clumped isotope thermometry: Patterns and implications.

PubMed

Defliese, William F; Lohmann, Kyger C

2015-05-15

Mass-47 CO(2) clumped isotope thermometry requires relatively large (~20 mg) samples of carbonate minerals due to detection limits and shot noise in gas source isotope ratio mass spectrometry (IRMS). However, it is unreasonable to assume that natural geologic materials are homogenous on the scale required for sampling. We show that sample heterogeneities can cause offsets from equilibrium Δ(47) values that are controlled solely by end member mixing and are independent of equilibrium temperatures. A numerical model was built to simulate and quantify the effects of end member mixing on Δ(47). The model was run in multiple possible configurations to produce a dataset of mixing effects. We verified that the model accurately simulated real phenomena by comparing two artificial laboratory mixtures measured using IRMS to model output. Mixing effects were found to be dependent on end member isotopic composition in δ(13)C and δ(18)O values, and independent of end member Δ(47) values. Both positive and negative offsets from equilibrium Δ(47) can occur, and the sign is dependent on the interaction between end member isotopic compositions. The overall magnitude of mixing offsets is controlled by the amount of variability within a sample; the larger the disparity between end member compositions, the larger the mixing offset. Samples varying by less than 2 ‰ in both δ(13)C and δ(18)O values have mixing offsets below current IRMS detection limits. We recommend the use of isotopic subsampling for δ(13)C and δ(18)O values to determine sample heterogeneity, and to evaluate any potential mixing effects in samples suspected of being heterogonous. Copyright © 2015 John Wiley & Sons, Ltd.

The Influence of Conditional Cash Transfers on Eligible Children and Their Siblings

ERIC Educational Resources Information Center

Lincove, Jane Arnold; Parker, Adam

2016-01-01

Conditional cash transfers (CCTs) are used to reduce poverty while incentivizing investments in children. Targeting CCTs to certain groups of children can improve efficiency, but positive effects on eligible children may be offset by reductions in investments for ineligible siblings. Using data from Nicaragua, we estimate program effects on…

Survival of tree seedligns across space and time: estimates from long-term count data

Treesearch

Brian Beckage; Michael Lavina; James S. Clark

2005-01-01

Tree diversity in forests may be maintained by variability in seedling recruitment. Although forest ecologists have emphasized the importance of canopy gaps in generating spatial variability that might promote tree regeneration, the effects of canopy gaps on seedling recruitment may be offset by dense forest understories.Large annual...

From sink to source: Regional variation in U.S. forest carbon futures

Treesearch

Dave Wear; John W. Coulston

2015-01-01

The sequestration of atmospheric carbon (C) in forests has partially offset C emissions in the United States (US) and might reduce overall costs of achieving emission targets, especially while transportation and energy sectors are transitioning to lower-carbon technologies. Using detailed forest inventory data for the conterminous US, we estimate...

A model for estimating windbreak carbon within COMET-Farm™

Treesearch

Justin ​Ziegler; Mark Easter; Amy Swan; James Brandle; William Ballesteros; Grant Domke; Adam Chambers; Marlen Eve; Keith Paustian

2016-01-01

Agroforestry as a land management practice presents a method for partially offsetting greenhouse gas emissions from agricultural land. Of all agroforestry practices in the United States, windbreaks in particular are used throughout the United States providing a useful starting point for deriving a modelling systemwhich could quantify the amount of carbon sequestered on...

An In-Rush Current Suppression Technique for the Solid-State Transfer Switch System

NASA Astrophysics Data System (ADS)

Cheng, Po-Tai; Chen, Yu-Hsing

More and more utility companies provide dual power feeders as a premier service of high power quality and reliability. To take advantage of this, the solid-state transfer switch (STS) is adopted to protect the sensitive load against the voltage sag. However, the fast transfer process may cause in-rush current on the load-side transformer due to the resulting DC-offset in its magnetic flux as the load-transfer is completed. The in-rush current can reach 2∼6 p.u. and it may trigger the over-current protections on the power feeder. This paper develops a flux estimation scheme and a thyristor gating scheme based on the impulse commutation bridge STS (ICBSTS) to minimize the DC-offset on the magnetic flux. By sensing the line voltages of both feeders, the flux estimator can predict the peak transient flux linkage at the moment of load-transfer and evaluate a suitable moment for the transfer to minimize the in-rush current. Laboratory test results are presented to validate the performance of the proposed system.

Multi-technique combination of space geodesy observations

NASA Astrophysics Data System (ADS)

Zoulida, Myriam; Pollet, Arnaud; Coulot, David; Biancale, Richard; Rebischung, Paul; Collilieux, Xavier

2014-05-01

Over the last few years, combination at the observation level (COL) of the different space geodesy techniques has been thoroughly studied. Various studies have shown that this type of combination can take advantage of common parameters. Some of these parameters, such as Zenithal Tropospheric Delays (ZTD), are available on co-location sites, where more than one technique is present. Local ties (LT) are provided for these sites, and act as intra-technique links and allow resulting terrestrial reference frames (TRF) to be homogeneous. However the use of LT can be problematic on weekly calculations, where their geographical distribution can be poor, and there are often differences observed between available LTs and space geodesy results. Similar co-locations can be found on multi-technique satellites, where more than one technique receiver is featured. A great advantage of these space ties (STs) is the densification of co-locations as the orbiting satellite acts as a moving station. The challenge of using space ties relies in the accurate knowledge or estimation of their values, as officially provided values are sometimes not reaching the required level of precision for the solution, due to receivers' or acting forces mismodelings and other factors. Thus, the necessity of an estimation and/or weighting strategy for the STs is introduced. To this day, on subsets of available data, using STs has shown promising results regarding the TRF determination through the stations' positions estimation, on the orbit determination of the GPS constellation and on the GPS antenna Phase Center Offsets and Variations (PCO and PCV) . In this study, results from a multi-technique combination including the Jason-2 satellite and its effect on the GNSS orbit determination during the CONT2011 period are presented, as well as some preliminary results on station positions' determination. Comparing resulting orbits with official solutions provides an assessment of the effect on the orbit calculation by introducing orbiting stations' observations. Moreover, simulated solutions will be presented, showing the effect of adding multi-technique observations on the estimation of STs parameters errors, such as Laser Retroreflector Offsets (LROs) or GNSS antennae Phase Center Offsets (PCOs).

Inversion analysis of slip distribution of the 2008 Iwate-Miyagi Nairiku earthquake: Very high stress-drop or a conjugate fault slip?

NASA Astrophysics Data System (ADS)

Fukahata, Y.; Fukushima, Y.

2009-05-01

On 14 June 2008, the Iwate-Miyagi Nairiku earthquake struck northeast Japan, where active seismicity has been observed under east-west compressional stress fields. The magnitude and hypocenter depth of the earthquake are reported as Mj 7.2 and 8 km, respectively. The earthquake is considered to have occurred on a west-dipping reverse fault with a roughly north-south strike. The earthquake caused significant surface displacements, which were detected by PALSAR, a Synthetic Aperture Radar (SAR) onboard the Japanese ALOS satellite. Several pairs of PALSAR images from six different paths are available to measure the coseismic displacements. Interferometric SAR (InSAR) is useful to obtain crustal displacements in the region where coseismic displacement is not so large (less than 1 m), whereas range and azimuth offsets provide displacement measurements up to a few meters on the whole processed area. We inverted the obtained displacement data to estimate slip distribution on the fault. Since the precise location and direction of the fault are not well known, the inverse problem is nonlinear. Following the method of Fukahata and Wright (2008), we resolved the weak non-linearity based on Akaike's Bayesian Information Criterion. We first estimated slip distribution by assuming a pure dip slip. The optimal fault geometry was estimated at dip 26 and strike 203 degrees. The maximum slip is more than 8 m and most slips concentrate at shallow depths (less than 4 km). The azimuth offset data suggest non-negligible right lateral slip components, so we next estimated slip distribution without fixing the rake angle. Again, a large slip area with the maximum slip of about 8 m in the shallow depth was obtained. Such slip models contradict with our existing common sense; our results indicate that the released strain is more than 10 to the power of -3. Range and azimuth offsets computed from SAR images obtained from both ascending and descending orbits appear to be more consistent with a conjugate fault slip, which contributes to lower the stress drop possibly to a level typical to this kind of earthquakes.

Risk and markets for ecosystem services.

PubMed

Bendor, Todd K; Riggsbee, J Adam; Doyle, Martin

2011-12-15

Market-based environmental regulations (e.g., cap and trade, "payments for ecosystem services") are increasingly common. However, few detailed studies of operating ecosystem markets have lent understanding to how such policies affect incentive structures for improving environmental quality. The largest U.S. market stems from the Clean Water Act provisions requiring ecosystem restoration to offset aquatic ecosystems damaged during development. We describe and test how variations in the rules governing this ecosystem market shift risk between regulators and entrepreneurs to promote ecological restoration. We analyze extensive national scale data to assess how two critical aspects of market structure - (a) the geographic scale of markets and (b) policies dictating the release of credits - affect the willingness of entrepreneurs to enter specific markets and produce credits. We find no discernible relationship between policies attempting to ease market entry and either the number of individual producers or total credits produced. Rather, market entry is primarily related to regional geography (the prevalence of aquatic ecosystems) and regional economic growth. Any improvements to policies governing ecosystem markets require explicit evaluation of the interplay between policy and risk elements affecting both regulators and entrepreneurial credit providers. Our findings extend to emerging, regulated ecosystem markets, including proposed carbon offset mechanisms, biodiversity banking, and water quality trading programs.

25 CFR 213.32 - Wells.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 1 2013-04-01 2013-04-01 false Wells. 213.32 Section 213.32 Indians BUREAU OF INDIAN... CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.32 Wells. The lessee shall agree (a) to drill and produce all wells necessary to offset or protect the leased land from drainage by wells on adjoining lands...

25 CFR 213.32 - Wells.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 1 2012-04-01 2011-04-01 true Wells. 213.32 Section 213.32 Indians BUREAU OF INDIAN... CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.32 Wells. The lessee shall agree (a) to drill and produce all wells necessary to offset or protect the leased land from drainage by wells on adjoining lands...

25 CFR 213.32 - Wells.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Wells. 213.32 Section 213.32 Indians BUREAU OF INDIAN... CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.32 Wells. The lessee shall agree (a) to drill and produce all wells necessary to offset or protect the leased land from drainage by wells on adjoining lands...

25 CFR 213.32 - Wells.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 1 2014-04-01 2014-04-01 false Wells. 213.32 Section 213.32 Indians BUREAU OF INDIAN... CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.32 Wells. The lessee shall agree (a) to drill and produce all wells necessary to offset or protect the leased land from drainage by wells on adjoining lands...

25 CFR 213.32 - Wells.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Wells. 213.32 Section 213.32 Indians BUREAU OF INDIAN... CIVILIZED TRIBES, OKLAHOMA, FOR MINING Operations § 213.32 Wells. The lessee shall agree (a) to drill and produce all wells necessary to offset or protect the leased land from drainage by wells on adjoining lands...

PR for Pennies: Low-Cost Library Public Relations.

ERIC Educational Resources Information Center

Baeckler, Virginia Van Wynen

This manual is designed to demystify a number of public relations techniques for those who wish to start producing their own materials with a minimum of time and money. Chapters focus on public relations; the library stereotype; words, ideas, and pictures; offset printing; creative print distribution; exhibits and posters; public speaking; and the…

Comparing Costs of Traditional and Specialty Probation for People With Serious Mental Illness.

PubMed

Skeem, Jennifer L; Montoya, Lina; Manchak, Sarah M

2018-05-15

Specialty mental health probation reduces the likelihood of rearrest for people with mental illness, who are overrepresented in the justice system. This study tested whether specialty probation was associated with lower costs than traditional probation during the two years after placement in probation. A longitudinal, matched study compared costs of behavioral health care and criminal justice contacts among 359 probationers with mental illness at prototypic specialty or traditional agencies. Compared with traditional officers, specialty officers supervised smaller caseloads, established better relationships with supervisees, and participated more in treatment. Participants and officers were interviewed, and administrative databases were integrated to capture service use and criminal justice contacts. Unit costs were attached to these data to estimate costs incurred by each participant over two years. Cost differences were estimated by using machine-learning algorithms combined with targeted maximum-likelihood estimation (TMLE), a double-robust estimator that accounts for associations between confounders and both treatment assignment and outcomes. Specialty probation cost $11,826 (p<.001) less per participant than traditional probation, with overall savings of about 51%. Specialty and traditional probation did not differ in criminal justice costs because the additional costs for supervision of specialty caseloads were offset by reduced recidivism. However, for behavioral health care, specialty probation cost an estimated $14,049 (p<.001) less per client than traditional probation. Greater outpatient costs were more than offset by reduced emergency, inpatient, and residential costs. Well-implemented specialty probation yielded substantial savings-and should be considered in justice reform efforts for people with mental illness.

GRACE-Based Estimates of GPS Satellite Antenna Phase Variations: Impact on Determining the Scale of the Terrestrial Reference Frame

NASA Astrophysics Data System (ADS)

Haines, B. J.; Bar-Sever, Y. E.; Bertiger, W.; Desai, S.; Owen, S.; Sibois, A.; Webb, F.

2007-12-01

Treating the GRACE tandem mission as an orbiting fiducial laboratory, we have developed new estimates of the phase and group-delay variations of the GPS transmitter antennas. Application of these antenna phase variation (APV) maps have shown great promise in reducing previously unexplained errors in our realization of GPS measurements from the TOPEX/POSEIDON (T/P; 1992--2005) and Jason-1 (2001--) missions. In particular, a 56 mm vertical offset in the solved-for position of the T/P receiver antenna is reduced to insignificance (less than 1 mm). For Jason-1, a spurious long-term (4-yr) drift in the daily antenna offset estimates is reduced from +3.7 to +0.1 mm/yr. Prior ground-based results, based on precise point positioning, also hint at the potential of the GRACE-based APV maps for scale determination, reducing the spurious scale rate by one half. In this paper, we report on the latest APV estimates from GRACE, and provide a further assessment of the impact of the APV maps on realizing the scale of the terrestrial reference frame (TRF) from GPS alone. To address this, we re-analyze over five years of data from a global (40+ station) ground network in a fiducial-free approach, using the new APV maps. A specialized multi-day GPS satellite orbit determination (OD) strategy is employed to better capitalize on dynamical constraints. The resulting estimates of TRF scale are compared to ITRF2005 in order to assess the quality of the solutions.

OFFSET - RAY TRACING OPTICAL ANALYSIS OF OFFSET SOLAR COLLECTOR FOR SPACE STATION SOLAR DYNAMIC POWER SYSTEM

NASA Technical Reports Server (NTRS)

Jefferies, K.

1994-01-01

OFFSET is a ray tracing computer code for optical analysis of a solar collector. The code models the flux distributions within the receiver cavity produced by reflections from the solar collector. It was developed to model the offset solar collector of the solar dynamic electric power system being developed for Space Station Freedom. OFFSET has been used to improve the understanding of the collector-receiver interface and to guide the efforts of NASA contractors also researching the optical components of the power system. The collector for Space Station Freedom consists of 19 hexagonal panels each containing 24 triangular, reflective facets. Current research is geared toward optimizing flux distribution inside the receiver via changes in collector design and receiver orientation. OFFSET offers many options for experimenting with the design of the system. The offset parabolic collector model configuration is determined by an input file of facet corner coordinates. The user may choose other configurations by changing this file, but to simulate collectors that have other than 19 groups of 24 triangular facets would require modification of the FORTRAN code. Each of the roughly 500 facets in the assembled collector may be independently aimed to smooth out, or tailor, the flux distribution on the receiver's wall. OFFSET simulates the effects of design changes such as in receiver aperture location, tilt angle, and collector facet contour. Unique features of OFFSET include: 1) equations developed to pseudo-randomly select ray originating sources on the Sun which appear evenly distributed and include solar limb darkening; 2) Cone-optics technique used to add surface specular error to the ray originating sources to determine the apparent ray sources of the reflected sun; 3) choice of facet reflective surface contour -- spherical, ideal parabolic, or toroidal; 4) Gaussian distributions of radial and tangential components of surface slope error added to the surface normals at the ten nodal points on each facet; and 5) color contour plots of receiver incident flux distribution generated by PATRAN processing of FORTRAN computer code output. OFFSET output includes a file of input data for confirmation, a PATRAN results file containing the values necessary to plot the flux distribution at the receiver surface, a PATRAN results file containing the intensity distribution on a 40 x 40 cm area of the receiver aperture plane, a data file containing calculated information on the system configuration, a file including the X-Y coordinates of the target points of each collector facet on the aperture opening, and twelve P/PLOT input data files to allow X-Y plotting of various results data. OFFSET is written in FORTRAN (70%) for the IBM VM operating system. The code contains PATRAN statements (12%) and P/PLOT statements (18%) for generating plots. Once the program has been run on VM (or an equivalent system), the PATRAN and P/PLOT files may be transferred to a DEC VAX (or equivalent system) with access to PATRAN for PATRAN post processing. OFFSET was written in 1988 and last updated in 1989. PATRAN is a registered trademark of PDA Engineering. IBM is a registered trademark of International Business Machines Corporation. DEC VAX is a registered trademark of Digital Equipment Corporation.

Experimental demonstration of OFDM/OQAM transmission with DFT-based channel estimation for visible laser light communications

NASA Astrophysics Data System (ADS)

He, Jing; Shi, Jin; Deng, Rui; Chen, Lin

2017-08-01

Recently, visible light communication (VLC) based on light-emitting diodes (LEDs) is considered as a candidate technology for fifth-generation (5G) communications, VLC is free of electromagnetic interference and it can simplify the integration of VLC into heterogeneous wireless networks. Due to the data rates of VLC system limited by the low pumping efficiency, small output power and narrow modulation bandwidth, visible laser light communication (VLLC) system with laser diode (LD) has paid more attention. In addition, orthogonal frequency division multiplexing/offset quadrature amplitude modulation (OFDM/OQAM) is currently attracting attention in optical communications. Due to the non-requirement of cyclic prefix (CP) and time-frequency domain well-localized pulse shapes, it can achieve high spectral efficiency. Moreover, OFDM/OQAM has lower out-of-band power leakage so that it increases the system robustness against inter-carrier interference (ICI) and frequency offset. In this paper, a Discrete Fourier Transform (DFT)-based channel estimation scheme combined with the interference approximation method (IAM) is proposed and experimentally demonstrated for VLLC OFDM/OQAM system. The performance of VLLC OFDM/OQAM system with and without DFT-based channel estimation is investigated. Moreover, the proposed DFT-based channel estimation scheme and the intra-symbol frequency-domain averaging (ISFA)-based method are also compared for the VLLC OFDM/OQAM system. The experimental results show that, the performance of EVM using the DFT-based channel estimation scheme is improved about 3dB compared with the conventional IAM method. In addition, the DFT-based channel estimation scheme can resist the channel noise effectively than that of the ISFA-based method.

Height system unification based on the Fixed Geodetic Boundary Value Problem with limited availability of gravity data

NASA Astrophysics Data System (ADS)

Porz, Lucas; Grombein, Thomas; Seitz, Kurt; Heck, Bernhard; Wenzel, Friedemann

2017-04-01

Regional height reference systems are generally related to individual vertical datums defined by specific tide gauges. The discrepancies of these vertical datums with respect to a unified global datum cause height system biases that range in an order of 1-2 m at a global scale. One approach for unification of height systems relates to the solution of a Geodetic Boundary Value Problem (GBVP). In particular, the fixed GBVP, using gravity disturbances as boundary values, is solved at GNSS/leveling benchmarks, whereupon height datum offsets can be estimated by least squares adjustment. In spherical approximation, the solution of the fixed GBVP is obtained by Hotine's spherical integral formula. However, this method relies on the global availability of gravity data. In practice, gravity data of the necessary resolution and accuracy is not accessible globally. Thus, the integration is restricted to an area within the vicinity of the computation points. The resulting truncation error can reach several meters in height, making height system unification without further consideration of this effect unfeasible. This study analyzes methods for reducing the truncation error by combining terrestrial gravity data with satellite-based global geopotential models and by modifying the integral kernel in order to accelerate the convergence of the resulting potential. For this purpose, EGM2008-derived gravity functionals are used as pseudo-observations to be integrated numerically. Geopotential models of different spectral degrees are implemented using a remove-restore-scheme. Three types of modification are applied to the Hotine-kernel and the convergence of the resulting potential is analyzed. In a further step, the impact of these operations on the estimation of height datum offsets is investigated within a closed loop simulation. A minimum integration radius in combination with a specific modification of the Hotine-kernel is suggested in order to achieve sub-cm accuracy for the estimation of height datum offsets.

Impact of Ezetimibe on the Rate of Cardiovascular-Related Hospitalizations and Associated Costs Among Patients With a Recent Acute Coronary Syndrome: Results From the IMPROVE-IT Trial (Improved Reduction of Outcomes: Vytorin Efficacy International Trial).

PubMed

Pokharel, Yashashwi; Chinnakondepalli, Khaja; Vilain, Katherine; Wang, Kaijun; Mark, Daniel B; Davies, Glenn; Blazing, Michael A; Giugliano, Robert P; Braunwald, Eugene; Cannon, Christopher P; Cohen, David J; Magnuson, Elizabeth A

2017-05-01

Ezetimibe, when added to simvastatin therapy, reduces cardiovascular events after recent acute coronary syndrome. However, the impact of ezetimibe on cardiovascular-related hospitalizations and associated costs is unknown. We used patient-level data from the IMPROVE-IT (Improved Reduction of Outcomes: Vytorin Efficacy International Trial) to examine the impact of simvastatin-ezetimibe versus simvastatin-placebo on cardiovascular-related hospitalizations and related costs (excluding drug costs) over 7 years follow-up. Medicare Severity-Diagnosis Related Groups were assigned to all cardiovascular hospitalizations. Hospital costs were estimated using Medicare reimbursement rates for 2013. Associated physician costs were estimated as a percentage of hospital costs. The impact of treatment assignment on hospitalization rates and costs was estimated using Poisson and linear regression, respectively. There was a significantly lower cardiovascular hospitalization rate with ezetimibe compared with placebo (risk ratio, 0.95; 95% confidence interval, 0.90-0.99; P =0.031), mainly attributable to fewer hospitalizations for percutaneous coronary intervention, angina, and stroke. Consequently, cardiovascular-related hospitalization costs over 7 years were $453 per patient lower with ezetimibe (95% confidence interval, -$38 to -$869; P =0.030). Although all prespecified subgroups had lower cost with ezetimibe therapy, patients with diabetes mellitus, patients aged ≥75 years, and patients at higher predicted risk for recurrent ischemic events had even greater cost offsets. Addition of ezetimibe to statin therapy in patients with a recent acute coronary syndrome leads to reductions in cardiovascular-related hospitalizations and associated costs, with the greatest cost offsets in high-risk patients. These cost reductions may completely offset the cost of the drug once ezetimibe becomes generic, and may lead to cost savings from the perspective of the healthcare system, if treatment with ezetimibe is targeted to high-risk patients. URL: https://www.clinicaltrials.gov. Unique Identifier: NCT00202878. © 2017 American Heart Association, Inc.

Partitioning nitrogen losses by natural abundance nitrogen isotope composition in a process-based statistical modelling framework

NASA Astrophysics Data System (ADS)

Dong, Ning; Wright, Ian; Prentice, Iain Colin

2017-04-01

Natural abundance of the stable isotope 15N is an under-utilized resource for research on the global terrestrial nitrogen cycle. Mass balance considerations suggest that if reactive N inputs have a roughly constant isotopic signature, soil δ15N should be mainly determined by the fraction of N losses by leaching - which barely discriminates against 15N - versus gaseous N losses, which discriminate strongly against 15N. We defined simple process-oriented functions of runoff (frunoff) and soil temperature (ftemp) and investigated the dependencies of soil and foliage δ15N (from global compilations of both types of measurement) on their ratio. Both plant and soil δ15N were found to systematically increase with ftemp/frunoff. Consistent with previous analyses, foliage δ15N was offset (more negative) with respect to soil δ15N, with significant differences in this offset between (from largest to smallest offset) ericoid, ectomycorrhizal, arbuscular mycorrhizal and non-mycorrhizal associated plants. δ15N values tend to be large and positive in the driest environments and to decline as frunoff increases, while also being lower in cold environments and increasing as ftemp increases. The fitted statistical model was used to estimate the gaseous fraction of total N losses from ecosystems (fgas) on a global grid basis. In common with earlier results, the largest values of fgas are predicted in the tropics and semi-arid subtropics. This analysis provides an indirectly estimated global mapping of fgas, which could be used as an improved benchmark for terrestrial nitrogen cycle models.

Comment on Geoengineering with seagrasses: is credit due where credit is given?

NASA Astrophysics Data System (ADS)

Oreska, Matthew P. J.; McGlathery, Karen J.; Emmer, Igino M.; Needelman, Brian A.; Emmett-Mattox, Stephen; Crooks, Stephen; Megonigal, J. Patrick; Myers, Doug

2018-03-01

In their recent review, ‘Geoengineering with seagrasses: is credit due where credit is given?,’ Johannessen and Macdonald (2016) invoke the prospect of carbon offset-credit over-allocation by the Verified Carbon Standard as a pretense for their concerns about published seagrass carbon burial rate and global stock estimates. Johannessen and Macdonald (2016) suggest that projects seeking offset-credits under the Verified Carbon Standard methodology VM0033: Methodology for Tidal Wetland and Seagrass Restoration will overestimate long-term (100 yr) sediment organic carbon (SOC) storage because issues affecting carbon burial rates bias storage estimates. These issues warrant serious consideration by the seagrass research community; however, VM0033 does not refer to seagrass SOC ‘burial rates’ or ‘storage.’ Projects seeking credits under VM0033 must document greenhouse gas emission reductions over time, relative to a baseline scenario, in order to receive credits. Projects must also monitor changes in carbon pools, including SOC, to confirm that observed benefits are maintained over time. However, VM0033 allows projects to conservatively underestimate project benefits by citing default values for specific accounting parameters, including CO2 emissions reductions. We therefore acknowledge that carbon crediting methodologies such as VM0033 are sensitive to the quality of the seagrass literature, particularly when permitted default factors are based in part on seagrass burial rates. Literature-derived values should be evaluated based on the concerns raised by Johannessen and Macdonald (2016), but these issues should not lead to credit over-allocation in practice, provided VM0033 is rigorously followed. These issues may, however, affect the feasibility of particular seagrass offset projects.

Late Quaternary alluviation and offset along the eastern Big Pine fault, southern California

USGS Publications Warehouse

DeLong, S.B.; Minor, S.A.; Arnold, L.J.

2007-01-01

Determining late Quaternary offset rates on specific faults within active mountain belts is not only a key component of seismic hazard analysis, but sheds light on regional tectonic development over geologic timescales. Here we report an estimate of dip-slip rate on the eastern Big Pine oblique-reverse fault in the upper Cuyama Valley within the western Transverse Ranges of southern California, and its relation to local landscape development. Optically stimulated luminescence (OSL) dating of sandy beds within coarse-grained alluvial deposits indicates that deposition of alluvium shed from the Pine Mountain massif occurred near the southern margin of the Cuyama structural basin at the elevation of the Cuyama River between 25 and 14??ka. This alluvial deposit has been offset ??? 10??m vertically by the eastern Big Pine fault, providing a latest Quaternary dip-slip rate estimate of ??? 0.9??m/ky based on a 50?? fault dip. Incision of the adjacent Cuyama River has exposed a section of older Cuyama River sediments beneath the Pine Mountain alluvium that accumulated between 45 and 30??ka on the down-thrown footwall block of the eastern Big Pine fault. Corroborative evidence for Holocene reverse-slip on the eastern Big Pine fault is ??? 1??m of incised bedrock that is characteristically exposed beneath 2-3.5??ka fill terraces in tributaries south of the fault. The eastern Big Pine fault in the Cuyama Valley area has no confirmed record of historic rupture; however, based on our results, we suggest the likelihood of multiple reverse-slip rupture events since 14??ka. ?? 2007 Elsevier B.V. All rights reserved.

An atmospheric perspective on North American carbon dioxide exchange: CarbonTracker.

PubMed

Peters, Wouter; Jacobson, Andrew R; Sweeney, Colm; Andrews, Arlyn E; Conway, Thomas J; Masarie, Kenneth; Miller, John B; Bruhwiler, Lori M P; Pétron, Gabrielle; Hirsch, Adam I; Worthy, Douglas E J; van der Werf, Guido R; Randerson, James T; Wennberg, Paul O; Krol, Maarten C; Tans, Pieter P

2007-11-27

We present an estimate of net CO(2) exchange between the terrestrial biosphere and the atmosphere across North America for every week in the period 2000 through 2005. This estimate is derived from a set of 28,000 CO(2) mole fraction observations in the global atmosphere that are fed into a state-of-the-art data assimilation system for CO(2) called CarbonTracker. By design, the surface fluxes produced in CarbonTracker are consistent with the recent history of CO(2) in the atmosphere and provide constraints on the net carbon flux independent from national inventories derived from accounting efforts. We find the North American terrestrial biosphere to have absorbed -0.65 PgC/yr (1 petagram = 10(15) g; negative signs are used for carbon sinks) averaged over the period studied, partly offsetting the estimated 1.85 PgC/yr release by fossil fuel burning and cement manufacturing. Uncertainty on this estimate is derived from a set of sensitivity experiments and places the sink within a range of -0.4 to -1.0 PgC/yr. The estimated sink is located mainly in the deciduous forests along the East Coast (32%) and the boreal coniferous forests (22%). Terrestrial uptake fell to -0.32 PgC/yr during the large-scale drought of 2002, suggesting sensitivity of the contemporary carbon sinks to climate extremes. CarbonTracker results are in excellent agreement with a wide collection of carbon inventories that form the basis of the first North American State of the Carbon Cycle Report (SOCCR), to be released in 2007. All CarbonTracker results are freely available at http://carbontracker.noaa.gov.

An atmospheric perspective on North American carbon dioxide exchange: CarbonTracker

PubMed Central

Peters, Wouter; Jacobson, Andrew R.; Sweeney, Colm; Andrews, Arlyn E.; Conway, Thomas J.; Masarie, Kenneth; Miller, John B.; Bruhwiler, Lori M. P.; Pétron, Gabrielle; Hirsch, Adam I.; Worthy, Douglas E. J.; van der Werf, Guido R.; Randerson, James T.; Wennberg, Paul O.; Krol, Maarten C.; Tans, Pieter P.

2007-01-01

We present an estimate of net CO2 exchange between the terrestrial biosphere and the atmosphere across North America for every week in the period 2000 through 2005. This estimate is derived from a set of 28,000 CO2 mole fraction observations in the global atmosphere that are fed into a state-of-the-art data assimilation system for CO2 called CarbonTracker. By design, the surface fluxes produced in CarbonTracker are consistent with the recent history of CO2 in the atmosphere and provide constraints on the net carbon flux independent from national inventories derived from accounting efforts. We find the North American terrestrial biosphere to have absorbed −0.65 PgC/yr (1 petagram = 1015 g; negative signs are used for carbon sinks) averaged over the period studied, partly offsetting the estimated 1.85 PgC/yr release by fossil fuel burning and cement manufacturing. Uncertainty on this estimate is derived from a set of sensitivity experiments and places the sink within a range of −0.4 to −1.0 PgC/yr. The estimated sink is located mainly in the deciduous forests along the East Coast (32%) and the boreal coniferous forests (22%). Terrestrial uptake fell to −0.32 PgC/yr during the large-scale drought of 2002, suggesting sensitivity of the contemporary carbon sinks to climate extremes. CarbonTracker results are in excellent agreement with a wide collection of carbon inventories that form the basis of the first North American State of the Carbon Cycle Report (SOCCR), to be released in 2007. All CarbonTracker results are freely available at http://carbontracker.noaa.gov. PMID:18045791

Effects of Channel Modification on Detection and Dating of Fault Scarps

NASA Astrophysics Data System (ADS)

Sare, R.; Hilley, G. E.

2016-12-01

Template matching of scarp-like features could potentially generate morphologic age estimates for individual scarps over entire regions, but data noise and scarp modification limits detection of fault scarps by this method. Template functions based on diffusion in the cross-scarp direction may fail to accurately date scarps near channel boundaries. Where channels reduce scarp amplitudes, or where cross-scarp noise is significant, signal-to-noise ratios decrease and the scarp may be poorly resolved. In this contribution, we explore the bias in morphologic age of a complex scarp produced by systematic changes in fault scarp curvature. For example, fault scarps may be modified by encroaching channel banks and mass failure, lateral diffusion of material into a channel, or undercutting parallel to the base of a scarp. We quantify such biases on morphologic age estimates using a block offset model subject to two-dimensional linear diffusion. We carry out a synthetic study of the effects of two-dimensional transport on morphologic age calculated using a profile model, and compare these results to a well- studied and constrained site along the San Andreas Fault at Wallace Creek, CA. This study serves as a first step towards defining regions of high confidence in template matching results based on scarp length, channel geometry, and near-scarp topography.

APPLICATION AND DEVELOPMENT OF APPROPRIATE TOOLS AND TECHNOLOGIES FOR COST-EFFECTIVE CARBON

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bill Stanley; Sandra Brown; Ellen Hawes

2003-09-01

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects,more » providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas impacts. The research described in this report occurred between July 1, 2002 and June 30, 2003. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: advanced videography testing; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.« less

Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bill Stanley; Sandra Brown; Patrick Gonzalez

2004-07-10

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects,more » providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas impacts. The research described in this report occurred between July 1, 2002 and June 30, 2003. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: remote sensing for carbon analysis; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.« less

Drilling of a deviated well: E. C. Newell 10056-D Meigs County, Ohio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodgers, J.A.

1982-09-30

The Department of Energy's (DOE) Eastern Gas Shales Program (EGSP) has focused primarily on the resource characterization of the Devonian shales in the Appalachian, Michigan and Illinois Basins, where the collective volume of gas in place is estimated to be on the order of 280 Tcf. From an early assessment of the petrophysical properties of these shales, attention now has turned to an understanding of the mechanisms controlling production of this unconventional-gas source. However, present knowledge of the production history of the Devonian shales is inadequate for an accurate estimation of the gas reserves, the optimum well spacing for gasmore » extraction, and the preferred stimulation techniques to be used. As part of this program, a Deviated Well Test was designed to evaluate the spacing of natural fractures in the Devonian shale in Meigs County, Ohio as a follow-on test to further define shale production characteristics and to assess the benefit of additional section gained by drilling through the producing interval at the approximate angle for dip of 60/sup 0/ from vertical. The Columbia Gas Transmission Company, E.C. Newell 10056-D well, on the same site as a previous Off-Set Well Test, was selected for this investigation. This report summarizes drilling operations on this Deviated Well Test.« less

Robust Real-Time Wide-Area Differential GPS Navigation

NASA Technical Reports Server (NTRS)

Yunck, Thomas P. (Inventor); Bertiger, William I. (Inventor); Lichten, Stephen M. (Inventor); Mannucci, Anthony J. (Inventor); Muellerschoen, Ronald J. (Inventor); Wu, Sien-Chong (Inventor)

1998-01-01

The present invention provides a method and a device for providing superior differential GPS positioning data. The system includes a group of GPS receiving ground stations covering a wide area of the Earth's surface. Unlike other differential GPS systems wherein the known position of each ground station is used to geometrically compute an ephemeris for each GPS satellite. the present system utilizes real-time computation of satellite orbits based on GPS data received from fixed ground stations through a Kalman-type filter/smoother whose output adjusts a real-time orbital model. ne orbital model produces and outputs orbital corrections allowing satellite ephemerides to be known with considerable greater accuracy than from die GPS system broadcasts. The modeled orbits are propagated ahead in time and differenced with actual pseudorange data to compute clock offsets at rapid intervals to compensate for SA clock dither. The orbital and dock calculations are based on dual frequency GPS data which allow computation of estimated signal delay at each ionospheric point. These delay data are used in real-time to construct and update an ionospheric shell map of total electron content which is output as part of the orbital correction data. thereby allowing single frequency users to estimate ionospheric delay with an accuracy approaching that of dual frequency users.

The role of elasticity in simulating long-term tectonic extension

NASA Astrophysics Data System (ADS)

Olive, Jean-Arthur; Behn, Mark D.; Mittelstaedt, Eric; Ito, Garrett; Klein, Benjamin Z.

2016-05-01

While elasticity is a defining characteristic of the Earth's lithosphere, it is often ignored in numerical models of long-term tectonic processes in favour of a simpler viscoplastic description. Here we assess the consequences of this assumption on a well-studied geodynamic problem: the growth of normal faults at an extensional plate boundary. We conduct 2-D numerical simulations of extension in elastoplastic and viscoplastic layers using a finite difference, particle-in-cell numerical approach. Our models simulate a range of faulted layer thicknesses and extension rates, allowing us to quantify the role of elasticity on three key observables: fault-induced topography, fault rotation, and fault life span. In agreement with earlier studies, simulations carried out in elastoplastic layers produce rate-independent lithospheric flexure accompanied by rapid fault rotation and an inverse relationship between fault life span and faulted layer thickness. By contrast, models carried out with a viscoplastic lithosphere produce results that may qualitatively resemble the elastoplastic case, but depend strongly on the product of extension rate and layer viscosity U × ηL. When this product is high, fault growth initially generates little deformation of the footwall and hanging wall blocks, resulting in unrealistic, rigid block-offset in topography across the fault. This configuration progressively transitions into a regime where topographic decay associated with flexure is fully accommodated within the numerical domain. In addition, high U × ηL favours the sequential growth of multiple short-offset faults as opposed to a large-offset detachment. We interpret these results by comparing them to an analytical model for the fault-induced flexure of a thin viscous plate. The key to understanding the viscoplastic model results lies in the rate-dependence of the flexural wavelength of a viscous plate, and the strain rate dependence of the force increase associated with footwall and hanging wall bending. This behaviour produces unrealistic deformation patterns that can hinder the geological relevance of long-term rifting models that assume a viscoplastic rheology.

ac electroosmotic pumping induced by noncontact external electrodes.

PubMed

Wang, Shau-Chun; Chen, Hsiao-Ping; Chang, Hsueh-Chia

2007-09-21

Electroosmotic (EO) pumps based on dc electroosmosis is plagued by bubble generation and other electrochemical reactions at the electrodes at voltages beyond 1 V for electrolytes. These disadvantages limit their throughput and offset their portability advantage over mechanical syringe or pneumatic pumps. ac electroosmotic pumps at high frequency (>100 kHz) circumvent the bubble problem by inducing polarization and slip velocity on embedded electrodes,1 but they require complex electrode designs to produce a net flow. We report a new high-throughput ac EO pump design based on induced-polarization on the entire channel surface instead of just on the electrodes. Like dc EO pumps, our pump electrodes are outside of the load section and form a cm-long pump unit consisting of three circular reservoirs (3 mm in diameter) connected by a 1x1 mm channel. The field-induced polarization can produce an effective Zeta potential exceeding 1 V and an ac slip velocity estimated as 1 mmsec or higher, both one order of magnitude higher than earlier dc and ac pumps, giving rise to a maximum throughput of 1 mulsec. Polarization over the entire channel surface, quadratic scaling with respect to the field and high voltage at high frequency without electrode bubble generation are the reasons why the current pump is superior to earlier dc and ac EO pumps.

Active Self-Testing Noise Measurement Sensors for Large-Scale Environmental Sensor Networks

PubMed Central

Domínguez, Federico; Cuong, Nguyen The; Reinoso, Felipe; Touhafi, Abdellah; Steenhaut, Kris

2013-01-01

Large-scale noise pollution sensor networks consist of hundreds of spatially distributed microphones that measure environmental noise. These networks provide historical and real-time environmental data to citizens and decision makers and are therefore a key technology to steer environmental policy. However, the high cost of certified environmental microphone sensors render large-scale environmental networks prohibitively expensive. Several environmental network projects have started using off-the-shelf low-cost microphone sensors to reduce their costs, but these sensors have higher failure rates and produce lower quality data. To offset this disadvantage, we developed a low-cost noise sensor that actively checks its condition and indirectly the integrity of the data it produces. The main design concept is to embed a 13 mm speaker in the noise sensor casing and, by regularly scheduling a frequency sweep, estimate the evolution of the microphone's frequency response over time. This paper presents our noise sensor's hardware and software design together with the results of a test deployment in a large-scale environmental network in Belgium. Our middle-range-value sensor (around €50) effectively detected all experienced malfunctions, in laboratory tests and outdoor deployments, with a few false positives. Future improvements could further lower the cost of our sensor below €10. PMID:24351634

Injection locking of violet laser diodes with a 3.2 GHz offset frequency for driving Raman transitions in 43Ca+.

PubMed

Keitch, B C; Thomas, N R; Lucas, D M

2013-03-15

Two cw single-mode violet (397 nm) diode lasers are locked to a single external-cavity master diode laser by optical injection locking. A double-pass 1.6 GHz acousto-optic modulator is used to provide a 3.2 GHz offset frequency between the two slave lasers. We achieve up to 20 mW usable output in each slave beam, with as little as 25 μW of injection power at room temperature. An optical heterodyne measurement of the beat note between the two slave beams gives a linewidth of ≤10 Hz at 3.2 GHz. We also estimate the free-running linewidth of the master laser to be approximately 3 MHz by optical heterodyning with a similar device.

Tangential velocity measurement using interferometric MTI radar

DOEpatents

Doerry, Armin W.; Mileshosky, Brian P.; Bickel, Douglas L.

2006-01-03

Radar systems use time delay measurements between a transmitted signal and its echo to calculate range to a target. Ranges that change with time cause a Doppler offset in phase and frequency of the echo. Consequently, the closing velocity between target and radar can be measured by measuring the Doppler offset of the echo. The closing velocity is also known as radial velocity, or line-of-sight velocity. Doppler frequency is measured in a pulse-Doppler radar as a linear phase shift over a set of radar pulses during some Coherent Processing Interval (CPI). An Interferometric Moving Target Indicator (MTI) radar can be used to measure the tangential velocity component of a moving target. Multiple baselines, along with the conventional radial velocity measurement, allow estimating the true 3-D velocity of a target.

New Constraints on Models for Time-Variable Displacement Rates on the San Jacinto Fault Zone, Southern California

NASA Astrophysics Data System (ADS)

Anderson, M.; Bennett, R.; Matti, J.

2004-12-01

Existing geodetic, geomorphic, and geologic studies yield apparently conflicting estimates of fault displacement rates over the last 1.5 m.y. in the greater San Andreas fault (SAF) system of southern California. Do these differences reflect biases in one or more of the inference methods, or is fault displacement really temporally variable? Arguments have been presented for both cases. We investigate the plausibility of variable-rate fault models by combining basin deposit provenance, fault trenching, seismicity, gravity, and magnetic data sets from the San Bernardino basin. These data allow us to trace the path and broad timing of strike-slip fault displacements in buried basement rocks, which in turn allows us to test weather variable-fault rate models fit the displacement path and rate data through the basin. The San Bernardino basin lies between the San Jacinto fault (SJF) and the SAF. Isostatic gravity signatures show a 2 km deep graben centered directly over the modern strand of the SJF, whereas the basin is shallow and a-symmetric next to the SAF. This observation indicates that stresses necessary to create the basin have been centered on the SJF for most of the basin's history. Linear magnetic anomalies, used as geologic markers, are offset ˜25 km across the northernmost strands of the SJF, which matches offset estimations south of the basin. These offset anomalies indicate that the SJF and SAF are discrete fault systems that do not directly interact south of the San Gabriel Mountains, therefore spatial slip variability combined with sparse sampling cannot explain the conflicting rate data. Furthermore, analyses of basin deposits indicate that movement on the SJF began between 1.3 to1.5 Ma, yielding an over-all average displacement rate in the range of 17 to 19 mm/yr, which is higher than some shorter-term estimates based on geodesy and geomorphology. Average displacement rates over this same time period for the San Bernardino strand of the SAF, on the other hand, are inferred to be low, consistent with some recent short-term estimates based on geodesy, but in contrast with estimates based on geomorphology. We conclude that either published estimates for the short-term SJF displacement rate do not accurately reflect the full SJF rate, or that the SJF rate has decreased over time, with implications for rate changes on other faults in the region. We explore the latter explanation with models for time-variable displacement rate for the greater SAF system that satisfy all existing data.

Dynamics and offset control of tethered space-tug system

NASA Astrophysics Data System (ADS)

Zhang, Jingrui; Yang, Keying; Qi, Rui

2018-01-01

Tethered space-tug system is regarded as one of the most promising active debris removal technologies to effectively decrease the steep increasing population of space debris. In order to suppress the spin of space debris, single-tethered space-tug system is employed by regulating the tether. Unfortunately, this system is underactuated as tether length is the only input, and there are two control objectives: the spinning debris and the vibration of tether. Thus, it may suffer great oscillations and result in failure in space debris removal. This paper presents the study of attitude stabilization of the single-tethered space-tug system using not only tether length but also the offset of tether attachment point to suppress the spin of debris, so as to accomplish the space debris removal mission. Firstly, a precise 3D mathematical model in which the debris and tug are both treated as rigid bodies is developed to study the dynamical evolution of the tethered space-tug system. The relative motion equation of the system is described using Lagrange method. Secondly, the dynamic characteristic of the system is analyzed and an offset control law is designed to stabilize the spin of debris by exploiting the variation of tether offset and the regulation of tether length. Besides, an estimation formula is proposed to evaluate the capability of tether for suppressing spinning debris. Finally, the effectiveness of attitude stabilization by the utilization of the proposed scheme is demonstrated via numerical case studies.

Long-term slip rate of the southern San Andreas Fault, from 10Be-26Al surface exposure dating of an offset alluvial fan

DOE Office of Scientific and Technical Information (OSTI.GOV)

der Woerd, J v; Klinger, Y; Sieh, K

We determine the long-term slip rate of the southern San Andreas Fault in the southeastern Indio Hills using {sup 10}Be and {sup 26}Al isotopes to date an offset alluvial fan surface. Field mapping complemented with topographic data, air photos and satellite images allow to precisely determine piercing points across the fault zone that are used to measure an offset of 565 {+-} 80 m. A total of twenty-six quartz-rich cobbles from three different fan surfaces were collected and dated. The tight cluster of nuclide concentrations from 19 samples out of 20 from the offset fan surface implies a simple exposuremore » history, negligible prior exposure and erosion, and yield an age of 35.5 {+-} 2.5 ka. The long-term slip rate of the San Andreas Fault south of Biskra Palms is thus 15.9 {+-} 3.4 mm/yr. This rate is about 10 mm/yr slower than geological (0-14 ka) and short-term geodetic estimates for this part of the San Andreas Fault implying changes in slip rate or in faulting behavior. This result puts new constraints on the slip rate of the San Jacinto and on the Eastern California Shear Zone for the last 35 ka. Our study shows that more sites along the major faults of southern California need to be targeted to better constrain the slip-rates over different time scales.« less

System and method for non-destructive evaluation of surface characteristics of a magnetic material

DOEpatents

Jiles, David C.; Sipahi, Levent B.

1994-05-17

A system and a related method for non-destructive evaluation of the surface characteristics of a magnetic material. The sample is excited by an alternating magnetic field. The field frequency, amplitude and offset are controlled according to a predetermined protocol. The Barkhausen response of the sample is detected for the various fields and offsets and is analyzed. The system produces information relating to the frequency content, the amplitude content, the average or RMS energy content, as well as count rate information, for each of the Barkhausen responses at each of the excitation levels applied during the protocol. That information provides a contiguous body of data, heretofore unavailable, which can be analyzed to deduce information about the surface characteristics of the material at various depths below the surface.

Phase ambiguity resolution for offset QPSK modulation systems

NASA Technical Reports Server (NTRS)

Nguyen, Tien M. (Inventor)

1991-01-01

A demodulator for Offset Quaternary Phase Shift Keyed (OQPSK) signals modulated with two words resolves eight possible combinations of phase ambiguity which may produce data error by first processing received I(sub R) and Q(sub R) data in an integrated carrier loop/symbol synchronizer using a digital Costas loop with matched filters for correcting four of eight possible phase lock errors, and then the remaining four using a phase ambiguity resolver which detects the words to not only reverse the received I(sub R) and Q(sub R) data channels, but to also invert (complement) the I(sub R) and/or Q(sub R) data, or to at least complement the I(sub R) and Q(sub R) data for systems using nontransparent codes that do not have rotation direction ambiguity.

Comparison of Different Attitude Correction Models for ZY-3 Satellite Imagery

NASA Astrophysics Data System (ADS)

Song, Wenping; Liu, Shijie; Tong, Xiaohua; Niu, Changling; Ye, Zhen; Zhang, Han; Jin, Yanmin

2018-04-01

ZY-3 satellite, launched in 2012, is the first civilian high resolution stereo mapping satellite of China. This paper analyzed the positioning errors of ZY-3 satellite imagery and conducted compensation for geo-position accuracy improvement using different correction models, including attitude quaternion correction, attitude angle offset correction, and attitude angle linear correction. The experimental results revealed that there exist systematic errors with ZY-3 attitude observations and the positioning accuracy can be improved after attitude correction with aid of ground controls. There is no significant difference between the results of attitude quaternion correction method and the attitude angle correction method. However, the attitude angle offset correction model produced steady improvement than the linear correction model when limited ground control points are available for single scene.

Policy Development for Biodiversity Offsets: A Review of Offset Frameworks

NASA Astrophysics Data System (ADS)

McKenney, Bruce A.; Kiesecker, Joseph M.

2010-01-01

Biodiversity offsets seek to compensate for residual environmental impacts of planned developments after appropriate steps have been taken to avoid, minimize or restore impacts on site. Offsets are emerging as an increasingly employed mechanism for achieving net environmental benefits, with offset policies being advanced in a wide range of countries (i.e., United States, Australia, Brazil, Colombia, and South Africa). To support policy development for biodiversity offsets, we review a set of major offset policy frameworks—US wetlands mitigation, US conservation banking, EU Natura 2000, Australian offset policies in New South Wales, Victoria, and Western Australia, and Brazilian industrial and forest offsets. We compare how the frameworks define offset policy goals, approach the mitigation process, and address six key issues for implementing offsets: (1) equivalence of project impacts with offset gains; (2) location of the offset relative to the impact site; (3) “additionality” (a new contribution to conservation) and acceptable types of offsets; (4) timing of project impacts versus offset benefits; (5) offset duration and compliance; and (6) “currency” and mitigation replacement ratios. We find substantial policy commonalities that may serve as a sound basis for future development of biodiversity offsets policy. We also identify issues requiring further policy guidance, including how best to: (1) ensure conformance with the mitigation hierarchy; (2) identify the most environmentally preferable offsets within a landscape context; and (3) determine appropriate mitigation replacement ratios.

Policy development for biodiversity offsets: a review of offset frameworks.

PubMed

McKenney, Bruce A; Kiesecker, Joseph M

2010-01-01

Biodiversity offsets seek to compensate for residual environmental impacts of planned developments after appropriate steps have been taken to avoid, minimize or restore impacts on site. Offsets are emerging as an increasingly employed mechanism for achieving net environmental benefits, with offset policies being advanced in a wide range of countries (i.e., United States, Australia, Brazil, Colombia, and South Africa). To support policy development for biodiversity offsets, we review a set of major offset policy frameworks-US wetlands mitigation, US conservation banking, EU Natura 2000, Australian offset policies in New South Wales, Victoria, and Western Australia, and Brazilian industrial and forest offsets. We compare how the frameworks define offset policy goals, approach the mitigation process, and address six key issues for implementing offsets: (1) equivalence of project impacts with offset gains; (2) location of the offset relative to the impact site; (3) "additionality" (a new contribution to conservation) and acceptable types of offsets; (4) timing of project impacts versus offset benefits; (5) offset duration and compliance; and (6) "currency" and mitigation replacement ratios. We find substantial policy commonalities that may serve as a sound basis for future development of biodiversity offsets policy. We also identify issues requiring further policy guidance, including how best to: (1) ensure conformance with the mitigation hierarchy; (2) identify the most environmentally preferable offsets within a landscape context; and (3) determine appropriate mitigation replacement ratios.

Carbon recovery rates following different wildfire risk mitigation treatments

Treesearch

M. Hurteau; M. North

2010-01-01

Sequestered forest carbon can provide a climate change mitigation benefit, but in dry temperate forests, wildfire poses a reversal risk to carbon offset projects. Reducing wildfire risk requires a reduction in and redistribution of carbon stocks, the benefit of which is only realized when wildfire occurs. To estimate the time needed to recover carbon removed and...

A technology development program for large space antennas

NASA Technical Reports Server (NTRS)

Russell, R. A.; Campbell, T. G.; Freeland, R. E.

1980-01-01

The design and application of the offset wrap rib and the maypole (hoop/column) antenna configurations are described. The NASA mission model that generically categorizes the classes of user requirements, as well as the methods used to determine critical technologies and requirements are discussed. Performance estimates for the mesh deployable antenna selected for development are presented.

Yield and financial performance estimates of four elite loblolly pine seed sources planted in the Western Gulf Region

Treesearch

Michael A. Blazier; A. Gordon Holley

2015-01-01

Eastern seed sources of loblolly pine (Pinus taeda L.) have been planted in the Western Gulf region for nearly three decades because they often have higher growth rates than local seed sources. However, productivity gains for eastern families are sometimes offset by poorer survival rates relative to local families.

Does Testing Cost Too Much?

ERIC Educational Resources Information Center

Test Service Bulletin, 1951

1951-01-01

Before a business adopts tests in personnel selection, it should be decided that the increased cost and bother are likely to be offset by the savings that come from this additional selection procedure. Fairly accurate estimates of the cost of testing can be made, but in educational testing it is harder than in businesses to measure the results in…

MODELING ASSESSMENT OF THE IMPACT OF NITROGEN OXIDES EMISSION REDUCTIONS ON OZONE AIR QUALITY IN THE EASTERN UNITED STATES: OFFSETTING INCREASES IN ENERGY USE

EPA Science Inventory

The objective of this study is to examine changes in ambient ozone concentrations estimated by a photochemical air quality model in response to the NOx emission reductions imposed on the utility sector. To accomplish this task, CMAQ air quality model simulations were performe...

Guiding U.S. Afforestation Policy through Terrestrial Carbon Cycle Modeling

NASA Astrophysics Data System (ADS)

Mykleby, P.; Snyder, P. K.; Twine, T. E.

2015-12-01

Afforestation has been proposed as a practical and viable solution for curtailing the ever-increasing levels of carbon dioxide in Earth's atmosphere. Individual states and multi-region cooperatives have established initiatives to offset carbon emissions using a variety of strategies, afforestation being one of them. While afforestation provides a positive benefit of increased carbon sequestration, this land cover change also produces a lower surface albedo, which can lead to local warming. Given these competing effects, carbon balance and surface energy budget analyses were performed for the northern United States and southern Canada, to determine where and for how long forest plantations should be planted to provide a positive benefit to the climate system. We use a dynamic vegetation model to analyze the competing effects of increased carbon sequestration versus increased net radiation at the surface from afforestation. In addition to determining where carbon sequestration (biogeochemical) would outweigh albedo (biophysical) effects, we calculate the amount of emissions offset for a variety of land use scenarios. As an example, in the state of Minnesota state officials have mandated that carbon emissions be reduced 80% from 2005 to 2050. While only taking into consideration land that is currently forested by mature forests and grasslands, the state would only offset about 11% of 2005 emissions annually by reforesting this land with younger, more productive forests. This example suggests that a significant amount of agricultural land would need to be converted into forest to make any sizeable offset to statewide greenhouse gas emissions.

Aesthetic Alliances in Poetry and Music: T. S. Eliot's Four Quartets and String Quartets by Bela Bartok.

ERIC Educational Resources Information Center

Boaz, Mildred Meyer

1979-01-01

This paper argues that, although T. S. Eliot's "Four Quartets" provoke comparisons with the late quartets of Beethoven, an analysis of Four Quartets and Bela Bartok's Fourth and Fifth String Quartets produces a clearer understanding of the formal structures in the poetry and music. Symmetries offset asymmetries. (Author/KC)

An Integrated Non-Mechanized System for Information Bulletins and a Keyword Index

ERIC Educational Resources Information Center

Whitehall, T.

1972-01-01

Described is an operating system for scanning, bulletin production and indexing which is very economical in the use of time. One typing onto offset masters is used to produce bulletins, slips for customers' personal files and for the library index. Indexing is done during scanning, not as a separate activity. (3 references) (Author/SJ)

The Organization of Catholic Secondary Schools: A Preliminary Statement on Catholic School Governance.

ERIC Educational Resources Information Center

Maltby, Gregory P.

This paper explores whether or not an effort to centralize the administration of several metropolitan Catholic high schools for the purpose of economy of resources would produce an unanticipated consequence that would severely offset any savings. The research suggests that Catholic parents perceive a difference among these schools in terms of…

Synthetic biology for microbial production of lipid-based biofuels.

PubMed

d'Espaux, Leo; Mendez-Perez, Daniel; Li, Rachel; Keasling, Jay D

2015-12-01

The risks of maintaining current CO2 emission trends have led to interest in producing biofuels using engineered microbes. Microbial biofuels reduce emissions because CO2 produced by fuel combustion is offset by CO2 captured by growing biomass, which is later used as feedstock for biofuel fermentation. Hydrocarbons found in petroleum fuels share striking similarity with biological lipids. Here we review synthetic metabolic pathways based on fatty acid and isoprenoid metabolism to produce alkanes and other molecules suitable as biofuels. We further discuss engineering strategies to optimize engineered biosynthetic routes, as well as the potential of synthetic biology for sustainable manufacturing. Published by Elsevier Ltd.

Sensitivity analyses of acoustic impedance inversion with full-waveform inversion

NASA Astrophysics Data System (ADS)

Yao, Gang; da Silva, Nuno V.; Wu, Di

2018-04-01

Acoustic impedance estimation has a significant importance to seismic exploration. In this paper, we use full-waveform inversion to recover the impedance from seismic data, and analyze the sensitivity of the acoustic impedance with respect to the source-receiver offset of seismic data and to the initial velocity model. We parameterize the acoustic wave equation with velocity and impedance, and demonstrate three key aspects of acoustic impedance inversion. First, short-offset data are most suitable for acoustic impedance inversion. Second, acoustic impedance inversion is more compatible with the data generated by density contrasts than velocity contrasts. Finally, acoustic impedance inversion requires the starting velocity model to be very accurate for achieving a high-quality inversion. Based upon these observations, we propose a workflow for acoustic impedance inversion as: (1) building a background velocity model with travel-time tomography or reflection waveform inversion; (2) recovering the intermediate wavelength components of the velocity model with full-waveform inversion constrained by Gardner’s relation; (3) inverting the high-resolution acoustic impedance model with short-offset data through full-waveform inversion. We verify this workflow by the synthetic tests based on the Marmousi model.

Compensation of the Ionospheric Effects on SAR Interferogram Based on Range Split-Spectrum and Azimuth Offset Methods - a Case Study of Yushu Earthquake

NASA Astrophysics Data System (ADS)

He, Y. F.; Zhu, W.; Zhang, Q.; Zhang, W. T.

2018-04-01

InSAR technique can measure the surface deformation with the accuracy of centimeter-level or even millimeter and therefore has been widely used in the deformation monitoring associated with earthquakes, volcanoes, and other geologic process. However, ionospheric irregularities can lead to the wavy fringes in the low frequency SAR interferograms, which disturb the actual information of geophysical processes and thus put severe limitations on ground deformations measurements. In this paper, an application of two common methods, the range split-spectrum and azimuth offset methods are exploited to estimate the contributions of the ionosphere, with the aim to correct ionospheric effects in interferograms. Based on the theoretical analysis and experiment, a performance analysis is conducted to evaluate the efficiency of these two methods. The result indicates that both methods can mitigate the ionospheric effect in SAR interferograms and the range split-spectrum method is more precise than the other one. However, it is also found that the range split-spectrum is easily contaminated by the noise, and the achievable accuracy of the azimuth offset method is limited by the ambiguous integral constant, especially with the strong azimuth variations induced by the ionosphere disturbance.

The dark matter of galaxy voids

NASA Astrophysics Data System (ADS)

Sutter, P. M.; Lavaux, Guilhem; Wandelt, Benjamin D.; Weinberg, David H.; Warren, Michael S.

2014-03-01

How do observed voids relate to the underlying dark matter distribution? To examine the spatial distribution of dark matter contained within voids identified in galaxy surveys, we apply Halo Occupation Distribution models representing sparsely and densely sampled galaxy surveys to a high-resolution N-body simulation. We compare these galaxy voids to voids found in the halo distribution, low-resolution dark matter and high-resolution dark matter. We find that voids at all scales in densely sampled surveys - and medium- to large-scale voids in sparse surveys - trace the same underdensities as dark matter, but they are larger in radius by ˜20 per cent, they have somewhat shallower density profiles and they have centres offset by ˜ 0.4Rv rms. However, in void-to-void comparison we find that shape estimators are less robust to sampling, and the largest voids in sparsely sampled surveys suffer fragmentation at their edges. We find that voids in galaxy surveys always correspond to underdensities in the dark matter, though the centres may be offset. When this offset is taken into account, we recover almost identical radial density profiles between galaxies and dark matter. All mock catalogues used in this work are available at http://www.cosmicvoids.net.

Investigation of TM Band-to-band Registration Using the JSC Registration Processor

NASA Technical Reports Server (NTRS)

Yao, S. S.; Amis, M. L.

1984-01-01

The JSC registration processor performs scene-to-scene (or band-to-band) correlation based on edge images. The edge images are derived from a percentage of the edge pixels calculated from the raw scene data, excluding clouds and other extraneous data in the scene. Correlations are performed on patches (blocks) of the edge images, and the correlation peak location in each patch is estimated iteratively to fractional pixel location accuracy. Peak offset locations from all patches over the scene are then considered together, and a variety of tests are made to weed out outliers and other inconsistencies before a distortion model is assumed. Thus, the correlation peak offset locations in each patch indicate quantitatively how well the two TM bands register to each other over that patch of scene data. The average of these offsets indicate the overall accuracies of the band-to-band registration. The registration processor was also used to register one acquisition to another acquisition of multitemporal TM data acquired over the same ground track. Band 4 images from both acquisitions were correlated and an rms error of a fraction of a pixel was routinely obtained.

Validation of maturity offset in a longitudinal sample of Polish girls.

PubMed

Malina, Robert M; Kozieł, Sławomir M

2014-01-01

This study attempted to validate an anthropometric equation for predicting age at peak height velocity (PHV) in 198 Polish girls followed longitudinally from 8 to 18 years. Maturity offset (years before or after PHV) was predicted from chronological age, mass, stature, sitting height and estimated leg length at each observation; predicted age at PHV was the difference between age and maturity offset. Actual age at PHV for each girl was derived with Preece-Baines Model 1. Predicted ages at PHV increased from 8 to16 years and varied relative to time before and after actual age at PHV. Predicted and actual ages at PHV did not differ at 9 years, but predicted overestimated actual age at PHV from 10 to 16 years. Girls of contrasting maturity status differed in predicted age at PHV from 8 to 14 years. In conclusion, predicted age at PHV is dependent upon age at prediction and individual differences in actual age at PHV, which limits its utility as an indicator of maturity timing in general and in sport talent programmes. It may have limited applicability as a categorical variable (pre-, post-PHV) among average maturing girls during the interval of the growth spurt, ~11.0-13.0 years.

Late Pleistocene-Holocene Activity of the Strike-slip Xianshuihe Fault Zone, Tibetan Plateau, Inferred from Tectonic Landforms

NASA Astrophysics Data System (ADS)

Lin, A.; Yan, B.

2017-12-01

Knowledges on the activity of the strike-slip fault zones on the Tibetan Plateau have been promoted greatly by the interpretation of remote sensing images (Molnar and Tapponnier, 1975; Tapponnier and Molnar, 1977). The active strike-slip Xianshuihe-Xiaojiang Fault System (XXFS), with the geometry of an arc projecting northeastwards, plays an important role in the crustal deformation of the Tibetan Plateau caused by the continental collision between the Indian and Eurasian plates. The Xianshuihe Fault Zone (XFZ) is located in the central segment of the XXFS and extends for 370 km, with a maximum sinistral offset of 60 km since 13‒5 Ma. In this study, we investigated the tectonic landforms and slip rate along the central segment of the left-lateral strike-slip XFZ. Field investigations and analysis of ttectonic landforms show that horizontal offset has been accumulated on the topographical markers of different scales that developed since the Last Glacial Maximum (LGM). The central segment of the XFZ is composed of three major faults: Yalahe, Selaha, and Zheduotang faults showing a right-stepping echelon pattern, that is characterized by systematical offset of drainages, alluvial fans and terrace risers with typical scissoring structures, indicating a structural feature of left-lateral strike-slip fault. Based on the offset glacial morphology and radiocarbon dating ages, we estimate the Late Pleistocene-Holocene slip rate to be 10 mm/yr for the central segment of the XFZ, which is consistent with that estimated from the GPS observations and geological evidence as reported previously. Across the central segment of the XFZ, the major Selaha and Zheduotang faults participate a slip rate of 5.8 mm/yr and 3.4 mm/yr, respectively. Detailed investigations of tectonic landforms are essential for the understanding the activity of active faults. Our findings suggest that the left-lateral slipping of the XFZ partitions the deformation of eastward extrusion and northeastward shortening of the central Tibetan Plateau to accommodate the continuing penetration of the Indian plate into the Eurasian plate.

Crustal dynamics project data analysis, 1987. Volume 2: Mobile VLBI geodetic results, 1982-1986

NASA Technical Reports Server (NTRS)

Ma, C.; Ryan, J. W.

1987-01-01

The Goddard VLBI group reports the results of analyzing 101 Mark III data sets acquired from mobile observing sites through the end of 1986 and available to the Crustal Dynamics Project. The fixed VLBI observations at Hat Creek, Ft. Davis, Mojave, and OVRO are included as they participate heavily in the mobile schedules. One large solution GLB171 was used to obtain baseline length and transverse evolutions. Radio source positions were estimated globally, while nutation offsets were estimated from each data set. The results include 28 mobile sites.

Empirical Relationships Among Magnitude and Surface Rupture Characteristics of Strike-Slip Faults: Effect of Fault (System) Geometry and Observation Location, Dervided From Numerical Modeling

NASA Astrophysics Data System (ADS)

Zielke, O.; Arrowsmith, J.

2007-12-01

In order to determine the magnitude of pre-historic earthquakes, surface rupture length, average and maximum surface displacement are utilized, assuming that an earthquake of a specific size will cause surface features of correlated size. The well known Wells and Coppersmith (1994) paper and other studies defined empirical relationships between these and other parameters, based on historic events with independently known magnitude and rupture characteristics. However, these relationships show relatively large standard deviations and they are based only on a small number of events. To improve these first-order empirical relationships, the observation location relative to the rupture extent within the regional tectonic framework should be accounted for. This however cannot be done based on natural seismicity because of the limited size of datasets on large earthquakes. We have developed the numerical model FIMozFric, based on derivations by Okada (1992) to create synthetic seismic records for a given fault or fault system under the influence of either slip- or stress boundary conditions. Our model features A) the introduction of an upper and lower aseismic zone, B) a simple Coulomb friction law, C) bulk parameters simulating fault heterogeneity, and D) a fault interaction algorithm handling the large number of fault patches (typically 5,000-10,000). The joint implementation of these features produces well behaved synthetic seismic catalogs and realistic relationships among magnitude and surface rupture characteristics which are well within the error of the results by Wells and Coppersmith (1994). Furthermore, we use the synthetic seismic records to show that the relationships between magntiude and rupture characteristics are a function of the observation location within the regional tectonic framework. The model presented here can to provide paleoseismologists with a tool to improve magnitude estimates from surface rupture characteristics, by incorporating the regional and local structural context which can be determined in the field: Assuming a paleoseismologist measures the offset along a fault caused by an earthquake, our model can be used to determine the probability distribution of magnitudes which are capable of producing the observed offset, accounting for regional tectonic setting and observation location.

Age, composition, and areal distribution of the Pliocene Lawlor Tuff, and three younger Pliocene tuffs, California and Nevada

USGS Publications Warehouse

Sarna-Wojcicki, Andrei M.; Deino, Alan L.; Fleck, Robert J.; McLaughlin, Robert J.; Wagner, David; Wan, Elmira; Wahl, David B.; Hillhouse, John W.; Perkins, Michael

2011-01-01

The Lawlor Tuff is a widespread dacitic tephra layer produced by Plinian eruptions and ash flows derived from the Sonoma Volcanics, a volcanic area north of San Francisco Bay in the central Coast Ranges of California, USA. The younger, chemically similar Huichica tuff, the tuff of Napa, and the tuff of Monticello Road sequentially overlie the Lawlor Tuff, and were erupted from the same volcanic field. We obtain new laser-fusion and incremental-heating 40Ar/39Ar isochron and plateau ages of 4.834 ± 0.011, 4.76 ± 0.03, ≤4.70 ± 0.03, and 4.50 ± 0.02 Ma (1 sigma), respectively, for these layers. The ages are concordant with their stratigraphic positions and are significantly older than those determined previously by the K-Ar method on the same tuffs in previous studies.Based on offsets of the ash-flow phase of the Lawlor Tuff by strands of the eastern San Andreas fault system within the northeastern San Francisco Bay area, total offset east of the Rodgers Creek–Healdsburg fault is estimated to be in the range of 36 to 56 km, with corresponding displacement rates between 8.4 and 11.6 mm/yr over the past ∼4.83 Ma.We identify these tuffs by their chemical, petrographic, and magnetic characteristics over a large area in California and western Nevada, and at a number of new localities. They are thus unique chronostratigraphic markers that allow correlation of marine and terrestrial sedimentary and volcanic strata of early Pliocene age for their region of fallout. The tuff of Monticello Road is identified only near its eruptive source.

Pricing the urban cooling benefits of solar panel deployment in Sydney, Australia

PubMed Central

Ma, S.; Goldstein, M.; Pitman, A. J.; Haghdadi, N.; MacGill, I.

2017-01-01

Cities import energy, which in combination with their typically high solar absorption and low moisture availability generates the urban heat island effect (UHI). The UHI, combined with human-induced warming, makes our densely populated cities particularly vulnerable to climate change. We examine the utility of solar photovoltaic (PV) system deployment on urban rooftops to reduce the UHI, and we price one potential value of this impact. The installation of PV systems over Sydney, Australia reduces summer maximum temperatures by up to 1 °C because the need to import energy is offset by local generation. This offset has a direct environmental benefit, cooling local maximum temperatures, but also a direct economic value in the energy generated. The indirect benefit associated with the temperature changes is between net AUD$230,000 and $3,380,000 depending on the intensity of PV systems deployment. Therefore, even very large PV installations will not offset global warming, but could generate enough energy to negate the need to import energy, and thereby reduce air temperatures. The energy produced, and the benefits of cooling beyond local PV installation sites, would reduce the vulnerability of urban populations and infrastructure to temperature extremes. PMID:28262843

Minimizing Environmental Magnetic Field Sources for nEDM

NASA Astrophysics Data System (ADS)

Brinson, Alex; Filippone, Bradley; Slutsky, Simon; Osthelder, Charles

2017-09-01

Measurement of the neutron's Electric Dipole Moment (nEDM) could potentially explain the Baryon Asymmetry Problem, and would suggest plausible extensions to the Standard Model. We will attempt to detect the nEDM by measuring the electric-field-dependent neutron precession frequency, which is highly sensitive to magnetic field gradients. In order to produce fields with sufficiently low gradients for our experiment, we eliminate environmental effects by offsetting the ambient field with a Field Compensation System (FCS), then magnetically shielding the reduced field with a Mu-Metal cylinder. We discovered that the strongest environmental effect in our lab came from iron rebar embedded in the floor beneath the proposed experiment location. The large extent and strength of the floor's magnetization made the effect too large to offset with the FCS, forcing us to relocate our apparatus. The floor's magnetic field was mapped with a Hall probe in order to determine the most viable experiment locations. A 3-axis Fluxgate magnetometer was then used to determine the floor field's drop-off and shape at these locations, and a final apparatus position was determined which minimized the floor's effect such that it could be effectively offset and shielded by our experiment. Caltech SFP Office.

Pricing the urban cooling benefits of solar panel deployment in Sydney, Australia.

PubMed

Ma, S; Goldstein, M; Pitman, A J; Haghdadi, N; MacGill, I

2017-03-06

Cities import energy, which in combination with their typically high solar absorption and low moisture availability generates the urban heat island effect (UHI). The UHI, combined with human-induced warming, makes our densely populated cities particularly vulnerable to climate change. We examine the utility of solar photovoltaic (PV) system deployment on urban rooftops to reduce the UHI, and we price one potential value of this impact. The installation of PV systems over Sydney, Australia reduces summer maximum temperatures by up to 1 °C because the need to import energy is offset by local generation. This offset has a direct environmental benefit, cooling local maximum temperatures, but also a direct economic value in the energy generated. The indirect benefit associated with the temperature changes is between net AUD$230,000 and $3,380,000 depending on the intensity of PV systems deployment. Therefore, even very large PV installations will not offset global warming, but could generate enough energy to negate the need to import energy, and thereby reduce air temperatures. The energy produced, and the benefits of cooling beyond local PV installation sites, would reduce the vulnerability of urban populations and infrastructure to temperature extremes.

The Performance of a Subsonic Diffuser Designed for High Speed Turbojet-Propelled Flight

NASA Technical Reports Server (NTRS)

Biesiadny, Thomas J. (Technical Monitor); Wendt, Bruce J.

2004-01-01

An initial-phase subsonic diffuser has been designed for the turbojet flowpath of the hypersonic x43B flight demonstrator vehicle. The diffuser fit into a proposed mixed-compression supersonic inlet system and featured a cross-sectional shape transitioning flowpath (high aspect ratio rectangular throat-to-circular engine face) and a centerline offset. This subsonic diffuser has been fabricated and tested at the W1B internal flow facility at NASA Glenn Research Center. At an operating throat Mach number of 0.79, baseline Pitot pressure recovery was found to be just under 0.9, and DH distortion intensity was about 0.4 percent. The diffuser internal flow stagnated, but did not separate on the offset surface of this initial-phase subsonic diffuser. Small improvements in recovery (+0.4 percent) and DH distortion (-32 percent) were obtained from using vane vortex generator flow control applied just downstream of the diffuser throat. The optimum vortex generator array patterns produced inflow boundary layer divergence (local downwash) on the offset surface centerline of the diffuser, and an inflow boundary layer convergence (local upwash) on the centerline of the opposite surface.

Estimation and correction of produced light from prompt gamma photons on luminescence imaging of water for proton therapy dosimetry

NASA Astrophysics Data System (ADS)

Yabe, Takuya; Komori, Masataka; Toshito, Toshiyuki; Yamaguchi, Mitsutaka; Kawachi, Naoki; Yamamoto, Seiichi

2018-02-01

Although the luminescence images of water during proton-beam irradiation using a cooled charge-coupled device camera showed almost the same ranges of proton beams as those measured by an ionization chamber, the depth profiles showed lower Bragg peak intensities than those measured by an ionization chamber. In addition, a broad optical baseline signal was observed in depths that exceed the depth of the Bragg peak. We hypothesize that this broad baseline signal originates from the interaction of proton-induced prompt gamma photons with water. These prompt gamma photons interact with water to form high-energy Compton electrons, which may cause luminescence or Cherenkov emission from depths exceeding the location of the Bragg peak. To clarify this idea, we measured the luminescence images of water during the irradiations of protons in water with minimized parallax errors, and also simulated the produced light by the interactions of prompt gamma photons with water. We corrected the measured depth profiles of the luminescence images by subtracting the simulated distributions of the produced light by the interactions of prompt gamma photons in water. Corrections were also conducted using the estimated depth profiles of the light of the prompt gamma photons, as obtained from the off-beam areas of the luminescence images of water. With these corrections, we successfully obtained depth profiles that have almost identical distributions as the simulated dose distributions for protons. The percentage relative height of the Bragg peak with corrections to that of the simulation data increased to 94% from 80% without correction. Also, the percentage relative offset heights of the deeper part of the Bragg peak with corrections decreased to 0.2%-0.4% from 4% without correction. These results indicate that the luminescence imaging of water has potential for the dose distribution measurements for proton therapy dosimetry.

Magnetic field observations in the near-field the 28 June 1992 Mw 7.3 Landers, California, earthquake

USGS Publications Warehouse

Johnston, M.J.; Mueller, R.J.; Sasai, Yoichi

1994-01-01

Recent reports suggest that large magnetic field changes occur prior to, and during, large earthquakes. Two continuously operating proton magnetometers, LSBM and OCHM, at distances of 17.3 and 24.2 km, respectively, from the epicenter of the 28 June 1992 Mw 7.3 Landers earthquake, recorded data through the earthquake and its aftershocks. These two stations are part of a differentially connected array of proton magnetometers that has been operated along the San Andreas fault since 1976. The instruments have a sensitivity of 0.25 nT or better and transmit data every 10 min through the GOES satellite to the USGS headquarters in Menlo Park, California. Seismomagnetic offsets of −1.2 ± 0.6 and −0.7 ± 0.7 nT were observed at these sites. In comparison, offsets of −0.3 ± 0.2 and −1.3 ± 0.2 nT were observed during the 8 July 1986 ML 5.9 North Palm Springs earthquake, which occurred directly beneath the OCHM magnetometer site. The observations are generally consistent with seismomagnetic models of the earthquake, in which fault geometry and slip have the same from as that determined by either inversion of the seismic data or inversion of geodetically determined ground displacements produced by the earthquake. In these models, right-lateral rupture occurs on connected fault segments in a homogeneous medium with average magnetization of 2 A/m. The fault-slip distribution has roughly the same form as the observed surface rupture, and the total moment release is 1.1 × 1020 Nm. There is no indication of diffusion-like character to the magnetic field offsets that might indicate these effects result from fluid flow phenomena. It thus seems unlikely that these earthquake-generated offsets and those produced by the North Palm Springs earthquake were generated by electrokinetic effects. Also, there are no indications of enhanced low-frequency magnetic noise before the earthquake at frequencies below 0.001 Hz.

Population-based cost-offset estimation for the treatment of borderline personality disorder: projected costs in a currently running, ideal health system.

PubMed

Wunsch, Eva-Maria; Kliem, Sören; Kröger, Christoph

2014-09-01

Borderline personality disorder (BPD) is considered one of the most expensive mental disorders in terms of direct and indirect costs. The aim of this study was to carry out a cost-offset estimation of disorder-specific psychotherapy for BPD at the population level. The study investigated whether the possible financial benefits of dialectical behavior therapy outweigh the therapy costs, assuming a currently running, ideal health system, and whether the estimated cost-benefit relationships change depending upon the number of patients willing to be treated. A formula was elaborated that allows the user to calculate cost-benefit relationships for various conservative or progressive scenarios, with different stages of individuals' willingness to be treated (10%-90%). The possible costs and benefits of BPD-related treatment were evaluated using a 12-month, prevalence-based approach. The annual costs for untreated BPD were 8.69 billion EUR annually. The cost-benefit relationship for the treatment remained constant at 1.52 for all scenarios, implying that for each EUR invested, 1.52 EUR can be gained within one year, independent of the willingness to be treated. Additional intangible benefits were calculated with the aid of Quality-Adjusted Life Years. Findings suggest that BPD-related treatment might well be efficient at the population level. Copyright © 2014 Elsevier Ltd. All rights reserved.

An analytical benchmark and a Mathematica program for MD codes: Testing LAMMPS on the 2nd generation Brenner potential

NASA Astrophysics Data System (ADS)

Favata, Antonino; Micheletti, Andrea; Ryu, Seunghwa; Pugno, Nicola M.

2016-10-01

An analytical benchmark and a simple consistent Mathematica program are proposed for graphene and carbon nanotubes, that may serve to test any molecular dynamics code implemented with REBO potentials. By exploiting the benchmark, we checked results produced by LAMMPS (Large-scale Atomic/Molecular Massively Parallel Simulator) when adopting the second generation Brenner potential, we made evident that this code in its current implementation produces results which are offset from those of the benchmark by a significant amount, and provide evidence of the reason.

Repetition of large stress drop earthquakes on Wairarapa fault, New Zealand, revealed by LiDAR data

NASA Astrophysics Data System (ADS)

Delor, E.; Manighetti, I.; Garambois, S.; Beaupretre, S.; Vitard, C.

2013-12-01

We have acquired high-resolution LiDAR topographic data over most of the onland trace of the 120 km-long Wairarapa strike-slip fault, New Zealand. The Wairarapa fault broke in a large earthquake in 1855, and this historical earthquake is suggested to have produced up to 18 m of lateral slip at the ground surface. This would make this earthquake a remarkable event having produced a stress drop much higher than commonly observed on other earthquakes worldwide. The LiDAR data allowed us examining the ground surface morphology along the fault at < 50 cm resolution, including in the many places covered with vegetation. In doing so, we identified more than 900 alluvial features of various natures and sizes that are clearly laterally offset by the fault. We measured the about 670 clearest lateral offsets, along with their uncertainties. Most offsets are lower than 100 m. Each measurement was weighted by a quality factor that quantifies the confidence level in the correlation of the paired markers. Since the slips are expected to vary along the fault, we analyzed the measurements in short, 3-5 km-long fault segments. The PDF statistical analysis of the cumulative offsets per segment reveals that the alluvial morphology has well recorded, at every step along the fault, no more than a few (3-6), well distinct cumulative slips, all lower than 80 m. Plotted along the entire fault, the statistically defined cumulative slip values document four, fairly continuous slip profiles that we attribute to the four most recent large earthquakes on the Wairarapa fault. The four slip profiles have a roughly triangular and asymmetric envelope shape that is similar to the coseismic slip distributions described for most large earthquakes worldwide. The four slip profiles have their maximum slip at the same place, in the northeastern third of the fault trace. The maximum slips vary from one event to another in the range 7-15 m; the most recent 1855 earthquake produced a maximum coseismic slip of 15 × 2 m at the ground surface. Our results thus confirm that the Wairarapa fault breaks in remarkably large stress drop earthquakes. Those repeating large earthquakes share both similar (rupture length, slip-length distribution, location of maximum slip) and distinct (maximum slip amplitudes) characteristics. Furthermore, the seismic behavior of the Wairarapa fault is markedly different from that of nearby large strike-slip faults (Wellington, Hope). The reasons for those differences in rupture behavior might reside in the intrinsic properties of the broken faults, especially in their structural maturity.

Opening of the Gulf of Guayaquil: quantifying the motion from the trench to the Andean Cordillera

NASA Astrophysics Data System (ADS)

Santana, E.; Dumont, J. F.; Vilema, W.; Pedoja, K.

2003-04-01

The Gulf of Guayaquil is a complex pull-apart opened at the south tip of the North Andean Block. The Guayaquil-Caracas Megashear (i.e. Dolores-Guayaquil Megashear) which bounds the North Andean Block to the east crosses the Western Andean Cordillera along the Pallatanga fault, and joins southwestward the Ecuadorian trench. According to paleogeographic data the Gulf of Guayaquil began to open about 9 Ma ago, which is evidenced now by about 100 km offset of the Early Neogene Progresso and Loja basins. A lesser post orogenic offset of about 60 km is observed along the Pallatanga fault, coherent with the offset of the piedmont of the Western Andean Cordillera. The discrepancy suggests a partition of the deformation at the south tip of the North Andean Block, part of the motion being accommodated by other small faults north of the Pallatanga fault zone and resulting in a pull apart motion and subsidence of the Daule-Babahoyo basin. The main curve of the Tallara Arc described by the trend of the trench from north Peru to north Ecuador shows a significant anomaly in front of the Gulf of Guayaquil. A 60 to 70 km minimum right hand deviation of the curve is observed, displayed in three segments delimited by faults. Neotectonic studies in the Santa Clara and Puná Islands located in the Gulf of Guayaquil show a regional E-W shortening during the Pleistocene, characterised by right lateral motion along the Zambapala Cordillera in Puná. Offset of river drainage and morphostructures in South Puná gives evidence of 3 km dextral offset which post-date marine terraces with an estimated age of M.I.S. 9 or 11, giving mean offset rates of 9 mm/y or 6.8 mm/y respectively. The conclusion underlines the following points: (1) These data suggest that the offset rate inside the Gulf of Guayaquil during the Late Quaternary is lower than the mean rate observed since 9 Ma. The apparent slow down may be due to the partition of the deformation of the Gulf of Guayaquil towards the Guayas, Daule and Babahoyo drainage area, evidenced by the seismic activity observed in this area. (2) The effect of the new partition of deformation is also evidenced by the evolution of the morphology on the north margin of the Gulf, resulting in the formation of the Puná Island since the last interglacial period. A NW-SW trending drainage pattern from the Progresso Basin to Puná, evidenced by a paleo estuary pattern in east Puná, was disrupted and overprinted by the new N-S drainage of the Guayas estuary, which shifted from east to west as a result. (3) The opening of the Gulf of Guayaquil has a significant effect on the trench, which is offset is several segments. Most of the motion is registered by the offset of the trench.

Estimating soil water content from ground penetrating radar coarse root reflections

NASA Astrophysics Data System (ADS)

Liu, X.; Cui, X.; Chen, J.; Li, W.; Cao, X.

2016-12-01

Soil water content (SWC) is an indispensable variable for understanding the organization of natural ecosystems and biodiversity. Especially in semiarid and arid regions, soil moisture is the plants primary source of water and largely determine their strategies for growth and survival, such as root depth, distribution and competition between them. Ground penetrating radar (GPR), a kind of noninvasive geophysical technique, has been regarded as an accurate tool for measuring soil water content at intermediate scale in past decades. For soil water content estimation with surface GPR, fixed antenna offset reflection method has been considered to have potential to obtain average soil water content between land surface and reflectors, and provide high resolution and few measurement time. In this study, 900MHz surface GPR antenna was used to estimate SWC with fixed offset reflection method; plant coarse roots (with diameters greater than 5 mm) were regarded as reflectors; a kind of advanced GPR data interpretation method, HADA (hyperbola automatic detection algorithm), was introduced to automatically obtain average velocity by recognizing coarse root hyperbolic reflection signals on GPR radargrams during estimating SWC. In addition, a formula was deduced to determine interval average SWC between two roots at different depths as well. We examined the performance of proposed method on a dataset simulated under different scenarios. Results showed that HADA could provide a reasonable average velocity to estimate SWC without knowledge of root depth and interval average SWC also be determined. When the proposed method was applied to estimation of SWC on a real-field measurement dataset, a very small soil water content vertical variation gradient about 0.006 with depth was captured as well. Therefore, the proposed method could be used to estimate average soil water content from ground penetrating radar coarse root reflections and obtain interval average SWC between two roots at different depths. It is very promising for measuring root-zone-soil-moisture and mapping soil moisture distribution around a shrub or even in field plot scale.

Bias in the Wagner-Nelson estimate of the fraction of drug absorbed.

PubMed

Wang, Yibin; Nedelman, Jerry

2002-04-01

To examine and quantify bias in the Wagner-Nelson estimate of the fraction of drug absorbed resulting from the estimation error of the elimination rate constant (k), measurement error of the drug concentration, and the truncation error in the area under the curve. Bias in the Wagner-Nelson estimate was derived as a function of post-dosing time (t), k, ratio of absorption rate constant to k (r), and the coefficient of variation for estimates of k (CVk), or CV% for the observed concentration, by assuming a one-compartment model and using an independent estimate of k. The derived functions were used for evaluating the bias with r = 0.5, 3, or 6; k = 0.1 or 0.2; CV, = 0.2 or 0.4; and CV, =0.2 or 0.4; for t = 0 to 30 or 60. Estimation error of k resulted in an upward bias in the Wagner-Nelson estimate that could lead to the estimate of the fraction absorbed being greater than unity. The bias resulting from the estimation error of k inflates the fraction of absorption vs. time profiles mainly in the early post-dosing period. The magnitude of the bias in the Wagner-Nelson estimate resulting from estimation error of k was mainly determined by CV,. The bias in the Wagner-Nelson estimate resulting from to estimation error in k can be dramatically reduced by use of the mean of several independent estimates of k, as in studies for development of an in vivo-in vitro correlation. The truncation error in the area under the curve can introduce a negative bias in the Wagner-Nelson estimate. This can partially offset the bias resulting from estimation error of k in the early post-dosing period. Measurement error of concentration does not introduce bias in the Wagner-Nelson estimate. Estimation error of k results in an upward bias in the Wagner-Nelson estimate, mainly in the early drug absorption phase. The truncation error in AUC can result in a downward bias, which may partially offset the upward bias due to estimation error of k in the early absorption phase. Measurement error of concentration does not introduce bias. The joint effect of estimation error of k and truncation error in AUC can result in a non-monotonic fraction-of-drug-absorbed-vs-time profile. However, only estimation error of k can lead to the Wagner-Nelson estimate of fraction of drug absorbed greater than unity.

Inferring the width of the upwelling region at mid-ocean ridges from the throttling effect of small-offset transforms: Implications for the dynamics of `normal' and plume-influenced mid- ocean ridges

NASA Astrophysics Data System (ADS)

Phipps Morgan, J.; Ranero, C. R.

2006-12-01

The fundamental question "How wide is the upwelling and melting region beneath mid-ocean ridges (MORs)?" remains a subject of ongoing debate after 4 decades of intensive study. The basic observational difficulty is that lateral melt migration has the potential to bring melt produced within a wide subaxial region to the ~2km- wide neovolcanic zone that has been observed to be the site of almost all oceanic crustal emplacement. Here we use an indirect approach to infer this width from the minimum length of the ridge-offsets that mark the limits of the `region of influence' of on-ridge plumes on the axial relief, axial morphology, and crustal thickness along the ridge — e.g. as seen along ridge segments influenced by the Galapagos and Iceland plumes, and at the terminations of fossil volcanic rifted margins and the paleo-Azores plume-ridge interaction. We adopt Vogt's [1972] hypothesis for along-ridge asthenospheric flow in a narrow vertical slot beneath the axis of plume- influenced `macro-segments'. We find that: (1) There is a threshold distance to the lateral offsets that bound plume-influenced macrosegments; all such `barrier offsets' are greater than ~30km, while smaller offsets do not appear to be a barrier to along-axis flow. (2) Recent seismic and E-M observations along the southern EPR are consistent with a narrow westward-dipping subaxial slot. (3) A similar pattern is seen in the often abrupt transitions between volcanic and non-volcanic rifted margins, which is discussed in a companion presentation by Ranero and Phipps Morgan (this meeting). (4) A ~30km width for the region of ridge upwelling and melting offers a simple conceptual explanation for the apparent ~30km threshold length for the existence of strike-slip transform faults and the occurrence of non-transform offsets at smaller ridge offset-distances. (5) It also offers a simple conceptual explanation for the largest scale of segmentation of axial relief seen at fast-spreading ridges; these 500-1000km `long wavelength undulations of the axis' (Macdonald et al., 1989) may be macro- segments sharing a single contiguous subaxial slot that is bent but not broken beneath non-transform offsets. (6) If asthenosphere consumption by plate-spreading is less than plume-supply into a macro-segment, then the shallow seafloor and excess gravitational spreading stresses associated with a plume-influenced ridge will lead to growth of the axial slot by ridge propagation, propagation that continues until the offset of the associated migrating shear zone becomes long enough to halt it. We think this is a promising conceptual framework with which to understand the dynamic similarities and differences between plume-influenced and `normal' mid-ocean ridges.

Stabilization of a self-referenced, prism-based, Cr:forsterite laser frequency comb using an intracavity prism

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tillman, Karl A.; Thapa, Rajesh; Knabe, Kevin

2009-12-20

The frequency comb from a prism-based Cr:forsterite laser has been frequency stabilized using intracavity prism insertion and pump power modulation. Absolute frequency measurements of a CW fiber laser stabilized to the P(13) transition of acetylene demonstrate a fractional instability of {approx}2x10{sup -11} at a 1 s gate time, limited by a commercial Global Positioning System (GPS)-disciplined rubidium oscillator. Additionally, absolute frequency measurements made simultaneously using a second frequency comb indicate relative instabilities of 3x10{sup -12} for both combs for a 1 s gate time. Estimations of the carrier-envelope offset frequency linewidth based on relative intensity noise and the response dynamicsmore » of the carrier-envelope offset to pump power changes confirm the observed linewidths.« less

Compilation of Published Estimates of Annual Geocenter Motions Using Space Geodesy

NASA Technical Reports Server (NTRS)

Elosegui, P.

2005-01-01

The definition of the term "geocenter motion" depends on the adopted origin of the reference frame. Common reference frames used in Space Geodesy include: the center of mass of the whole Earth (CM), the center of mass of the Solid Earth without mass load (CE), and the center of figure of the outer surface of the Solid Earth (CF). There are two established definitions of the term geocenter: one, the vector offset of CF relative to CM and, two, the reverse, the vector offset of CM relative to CF. Obviously, their amplitude is the same and their phase differs by 180 deg. Following Dong et al. [2003], we label the first X(sub CF, sup CM) and the second X(sup CF, sup CM) (i.e., the superscript represents the frame, the subscript represents any point in the frame).

Automatic estimation of detector radial position for contoured SPECT acquisition using CT images on a SPECT/CT system.

PubMed

Liu, Ruijie Rachel; Erwin, William D

2006-08-01

An algorithm was developed to estimate noncircular orbit (NCO) single-photon emission computed tomography (SPECT) detector radius on a SPECT/CT imaging system using the CT images, for incorporation into collimator resolution modeling for iterative SPECT reconstruction. Simulated male abdominal (arms up), male head and neck (arms down) and female chest (arms down) anthropomorphic phantom, and ten patient, medium-energy SPECT/CT scans were acquired on a hybrid imaging system. The algorithm simulated inward SPECT detector radial motion and object contour detection at each projection angle, employing the calculated average CT image and a fixed Hounsfield unit (HU) threshold. Calculated radii were compared to the observed true radii, and optimal CT threshold values, corresponding to patient bed and clothing surfaces, were found to be between -970 and -950 HU. The algorithm was constrained by the 45 cm CT field-of-view (FOV), which limited the detected radii to < or = 22.5 cm and led to occasional radius underestimation in the case of object truncation by CT. Two methods incorporating the algorithm were implemented: physical model (PM) and best fit (BF). The PM method computed an offset that produced maximum overlap of calculated and true radii for the phantom scans, and applied that offset as a calculated-to-true radius transformation. For the BF method, the calculated-to-true radius transformation was based upon a linear regression between calculated and true radii. For the PM method, a fixed offset of +2.75 cm provided maximum calculated-to-true radius overlap for the phantom study, which accounted for the camera system's object contour detect sensor surface-to-detector face distance. For the BF method, a linear regression of true versus calculated radius from a reference patient scan was used as a calculated-to-true radius transform. Both methods were applied to ten patient scans. For -970 and -950 HU thresholds, the combined overall average root-mean-square (rms) error in radial position for eight patient scans without truncation were 3.37 cm (12.9%) for PM and 1.99 cm (8.6%) for BF, indicating BF is superior to PM in the absence of truncation. For two patient scans with truncation, the rms error was 3.24 cm (12.2%) for PM and 4.10 cm (18.2%) for BF. The slightly better performance of PM in the case of truncation is anomalous, due to FOV edge truncation artifacts in the CT reconstruction, and thus is suspect. The calculated NCO contour for a patient SPECT/CT scan was used with an iterative reconstruction algorithm that incorporated compensation for system resolution. The resulting image was qualitatively superior to the image obtained by reconstructing the data using the fixed radius stored by the scanner. The result was also superior to the image reconstructed using the iterative algorithm provided with the system, which does not incorporate resolution modeling. These results suggest that, under conditions of no or only mild lateral truncation of the CT scan, the algorithm is capable of providing radius estimates suitable for iterative SPECT reconstruction collimator geometric resolution modeling.

Interindustry Analysis of the Impact of Federal Support for Academic Science on the Economy of New York State.

ERIC Educational Resources Information Center

Muir, Albert E.

1983-01-01

Economic activity generated by federally-supported research and development in New York State is estimated at 3.7 times the level of original federal spending, generating enough national and state tax revenues to offset the original federal outlay of taxpayers' money. Results support continued aid to higher education during fiscal crises. (MSE)

2012-13 Operating Grants: Too Little to Offset District Budget Shortfalls. BCTF Research Report. Section V. 2012-EF-01

ERIC Educational Resources Information Center

White, Margaret

2012-01-01

The BC Ministry of Education announcement about 2012-13 operating grants estimates includes "new" funding to districts of $11.2 million for vulnerable students, $10.7 million for districts to implement elements of the Education Plan, and $21.8 million to address "districts' differing geographic circumstances." This makes for a…

Adaptive Offset Correction for Intracortical Brain Computer Interfaces

PubMed Central

Homer, Mark L.; Perge, János A.; Black, Michael J.; Harrison, Matthew T.; Cash, Sydney S.; Hochberg, Leigh R.

2014-01-01

Intracortical brain computer interfaces (iBCIs) decode intended movement from neural activity for the control of external devices such as a robotic arm. Standard approaches include a calibration phase to estimate decoding parameters. During iBCI operation, the statistical properties of the neural activity can depart from those observed during calibration, sometimes hindering a user’s ability to control the iBCI. To address this problem, we adaptively correct the offset terms within a Kalman filter decoder via penalized maximum likelihood estimation. The approach can handle rapid shifts in neural signal behavior (on the order of seconds) and requires no knowledge of the intended movement. The algorithm, called MOCA, was tested using simulated neural activity and evaluated retrospectively using data collected from two people with tetraplegia operating an iBCI. In 19 clinical research test cases, where a nonadaptive Kalman filter yielded relatively high decoding errors, MOCA significantly reduced these errors (10.6 ±10.1%; p<0.05, pairwise t-test). MOCA did not significantly change the error in the remaining 23 cases where a nonadaptive Kalman filter already performed well. These results suggest that MOCA provides more robust decoding than the standard Kalman filter for iBCIs. PMID:24196868

Processing of a nine-component near-offset VSP for seismic anisotropy

DOE Office of Scientific and Technical Information (OSTI.GOV)

MacBeth, C.; Li, X.Y.; Zeng, X.

1997-03-01

A convolutional sequence of matrix operators is offered as a convenient deterministic scheme for processing a multicomponent vertical seismic profile (VSP). This sequence is applied to a nine-component near-offset VSP recorded at the Conoco borehole test facility, Kay County, Oklahoma. These data are corrected for tool spin and near-surface anisotropy together with source coupling or imbalance. After wave-field separation using a standard f-k filter, each source and receiver pair for the upgoing waves is adjusted to a common reference depth using a matrix operator based on the downgoing wavefield. The up- and downgoing waves are then processed for anisotropy bymore » a similarity transformation, to separate the qS1 and qS2 waves, from which the anisotropic properties are estimated. These estimates reveal a strong (apparent) vertical birefringence in the near-surface, but weak or moderate values for the majority of the subsurface. The target zone consists of a thin sandstone and deeper shale layer, both of which possess a strong vertical birefringence. The sandstone corresponds to a zone of known fluid flow. An observed qS2 attenuation and polarization change in the shale suggest it contains large fractures.« less

Termination Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruce McCarl and Dhazngilly

2004-01-07

The results of this project include: (1) Development of econometrically estimated marginal abatement and associated production curves describing response of agricultural and forestry emissions/sink/offsets enhancements for use in integrated assessments. Curves were developed that reflected agricultural, and forestry production of traditional commodities, carbon and other greenhouse gas offsets and biofuels given signals of general commodity demand, and carbon and energy prices. (2) Integration of the non-dynamic curves from (1) into a version of the PNNL SGM integrated assessment model was done in cooperation with Dr. Ronald Sands at PNNL. The results were reported at the second DOE conference on sequestrationmore » in the paper listed and the abstract is in Annex B of this report. (3) Alternative agricultural sequestration estimates were developed in conjunction with personnel at Colorado State University using CENTURY and analyses can operate under the use of agricultural soil carbon data from either the EPIC or CENTURY models. (4) A major effort was devoted to understanding the possible role and applicable actions from agriculture. (5) Work was done with EPA and EIA to update the biofuel data and assumptions resulting in some now emerging results showing the criticality of biofuel assumptions.« less

Advanced vehicles: Costs, energy use, and macroeconomic impacts

NASA Astrophysics Data System (ADS)

Wang, Guihua

Advanced vehicles and alternative fuels could play an important role in reducing oil use and changing the economy structure. We developed the Costs for Advanced Vehicles and Energy (CAVE) model to investigate a vehicle portfolio scenario in California during 2010-2030. Then we employed a computable general equilibrium model to estimate macroeconomic impacts of the advanced vehicle scenario on the economy of California. Results indicate that, due to slow fleet turnover, conventional vehicles are expected to continue to dominate the on-road fleet and gasoline is the major transportation fuel over the next two decades. However, alternative fuels could play an increasingly important role in gasoline displacement. Advanced vehicle costs are expected to decrease dramatically with production volume and technological progress; e.g., incremental costs for fuel cell vehicles and hydrogen could break even with gasoline savings in 2028. Overall, the vehicle portfolio scenario is estimated to have a slightly negative influence on California's economy, because advanced vehicles are very costly and, therefore, the resulting gasoline savings generally cannot offset the high incremental expenditure on vehicles and alternative fuels. Sensitivity analysis shows that an increase in gasoline price or a drop in alternative fuel prices could offset a portion of the negative impact.

Slowing extrusion tectonics: Lowered estimate of post-Early Miocene slip rate for the Altyn Tagh fault

USGS Publications Warehouse

Yue, Y.; Ritts, B.D.; Graham, S.A.; Wooden, J.L.; Gehrels, G.E.; Zhang, Z.

2004-01-01

Determination of long-term slip rate for the Altyn Tagh fault is essential for testing whether Asian tectonics is dominated by lateral extrusion or distributed crustal shortening. Previous slip-history studies focused on either Quaternary slip-rate measurements or pre-Early Miocene total-offset estimates and do not allow a clear distinction between rates based on the two. The magmatic and metamorphic history revealed by SHRIMP zircon dating of clasts from Miocene conglomerate in the Xorkol basin north of the Altyn Tagh fault strikingly matches that of basement in the southern Qilian Shan and northern Qaidam regions south of the fault. This match requires that the post-Early Miocene long-term slip rate along the Altyn Tagh fault cannot exceed 10 mm/year, supporting the hypothesis of distributed crustal thickening for post-Early Miocene times. This low long-term slip rate and recently documented large pre-Early Miocene cumulative offset across the fault support a two-stage evolution, wherein Asian tectonics was dominated by lateral extrusion before the end of Early Miocene, and since then has been dominated by distributed crustal thickening and rapid plateau uplift. ?? 2003 Elsevier B.V. All rights reserved.

Nitrogen Fertilization Effects on Net Ecosystem and Net Primary Productivities as Determined from Flux Tower, Biometric, and Model Estimates for a Coastal Douglas-fir Forest in British Columbia

NASA Astrophysics Data System (ADS)

Trofymow, J. A.; Metsaranta, J. M.; Black, T. A.; Jassal, R. S.; Filipescu, C.

2013-12-01

In coastal BC, 6,000-10,000 ha of public and significant areas of private forest land are annually fertilized with nitrogen, with or without thinning, to increase merchantable wood and reduce rotation age. Fertilization has also been viewed as a way to increase carbon (C) sequestration in forests and obtain C offsets. Such offset projects must demonstrate additionality with reference to a baseline and include monitoring to verify net C gains over the project period. Models in combination with field-plot measurements are currently the accepted methods for most C offset protocols. On eastern Vancouver Island, measurements of net ecosystem production (NEP), ecosystem respiration (Re) and gross primary productivity (GPP) using the eddy-covariance (EC) technique as well as component C fluxes and stocks have been made since 1998 in an intermediate-aged Douglas-fir dominated forest planted in 1949. In January 2007 an area around the EC flux tower was aerially fertilized with 200 kg urea-N ha-1. Ground plots in the fertilized area and an adjacent unfertilized control area were also monitored for soil (Rs) and heterotrophic (Rh) respiration, litterfall, and tree growth. To determine fertilization effects on whole tree growth, sample trees were felled in both areas for the 4-year (2003-06) pre- and the 4-year (2007-10) post-fertilization periods and were compared with EC NEP estimates and tree-ring based NEP estimates from Carbon Budget Model - Canadian Forest Sector (CBM-CFS3) for the same periods. Empirical equations using climate and C fluxes from 1998-2006 were derived to estimate what the EC fluxes would have been in 2007-10 for the fertilized area had it been unfertilized. Mean EC NEP for 2007-10 was 561 g C m2 y-1 , a 64% increase above pre-fertilization NEP (341 g C m2 y-1) or 28% increase above estimated unfertilized NEP (438 g C m2 y-1). Most of the increase was attributed to increased tree C uptake (i.e., GPP), with little change in Re. In 2007 fertilization caused a small increase in Rs and litter decay, and a small decrease in Rh. Litterfall rates averaged 100 g C m2 y-1 and did not differ between fertilized and control plots. Stem wood increments for 2007-10 indicated aboveground growth in fertilized trees was 35% greater than in control trees. However this was due to fertilized tree growth being 30% greater and control trees 5% less when compared to growth in the pre-fertilization period. Preliminary examination of root wood increments indicated that the post-fertilization growth was less than pre-fertilization growth, suggesting that the post-fertilization NPP was lower than if just estimated from stem wood. Mean CBM-CFS3 NEP for seven groundplots around the tower were 465 g C m2 y-1 for 2007-10, a 34% increase above pre-fertilization model NEP (347 g C m2 y-1). Using post- and pre-fertilization values, fertilization effects on EC NEP (64%) were nearly twice that of CBM-CFS3 model NEP (34%) or biometric tree growth (30%). However, if fertilized and unfertilized control values for 2007-10 were used; fertilization effects on EC NEP (28%) were comparable to those from biometric tree growth (35%). Results suggest choice of an appropriate baseline will be important in determining the C gains of forest C offset projects.

A line-source method for aligning on-board and other pinhole SPECT systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Susu; Bowsher, James; Yin, Fang-Fang

2013-12-15

Purpose: In order to achieve functional and molecular imaging as patients are in position for radiation therapy, a robotic multipinhole SPECT system is being developed. Alignment of the SPECT system—to the linear accelerator (LINAC) coordinate frame and to the coordinate frames of other on-board imaging systems such as cone-beam CT (CBCT)—is essential for target localization and image reconstruction. An alignment method that utilizes line sources and one pinhole projection is proposed and investigated to achieve this goal. Potentially, this method could also be applied to the calibration of the other pinhole SPECT systems.Methods: An alignment model consisting of multiple alignmentmore » parameters was developed which maps line sources in three-dimensional (3D) space to their two-dimensional (2D) projections on the SPECT detector. In a computer-simulation study, 3D coordinates of line-sources were defined in a reference room coordinate frame, such as the LINAC coordinate frame. Corresponding 2D line-source projections were generated by computer simulation that included SPECT blurring and noise effects. The Radon transform was utilized to detect angles (α) and offsets (ρ) of the line-source projections. Alignment parameters were then estimated by a nonlinear least squares method, based on the α and ρ values and the alignment model. Alignment performance was evaluated as a function of number of line sources, Radon transform accuracy, finite line-source width, intrinsic camera resolution, Poisson noise, and acquisition geometry. Experimental evaluations were performed using a physical line-source phantom and a pinhole-collimated gamma camera attached to a robot.Results: In computer-simulation studies, when there was no error in determining angles (α) and offsets (ρ) of the measured projections, six alignment parameters (three translational and three rotational) were estimated perfectly using three line sources. When angles (α) and offsets (ρ) were provided by the Radon transform, estimation accuracy was reduced. The estimation error was associated with rounding errors of Radon transform, finite line-source width, Poisson noise, number of line sources, intrinsic camera resolution, and detector acquisition geometry. Statistically, the estimation accuracy was significantly improved by using four line sources rather than three and by thinner line-source projections (obtained by better intrinsic detector resolution). With five line sources, median errors were 0.2 mm for the detector translations, 0.7 mm for the detector radius of rotation, and less than 0.5° for detector rotation, tilt, and twist. In experimental evaluations, average errors relative to a different, independent registration technique were about 1.8 mm for detector translations, 1.1 mm for the detector radius of rotation (ROR), 0.5° and 0.4° for detector rotation and tilt, respectively, and 1.2° for detector twist.Conclusions: Alignment parameters can be estimated using one pinhole projection of line sources. Alignment errors are largely associated with limited accuracy of the Radon transform in determining angles (α) and offsets (ρ) of the line-source projections. This alignment method may be important for multipinhole SPECT, where relative pinhole alignment may vary during rotation. For pinhole and multipinhole SPECT imaging on-board radiation therapy machines, the method could provide alignment of SPECT coordinates with those of CBCT and the LINAC.« less

A line-source method for aligning on-board and other pinhole SPECT systems

PubMed Central

Yan, Susu; Bowsher, James; Yin, Fang-Fang

2013-01-01

Purpose: In order to achieve functional and molecular imaging as patients are in position for radiation therapy, a robotic multipinhole SPECT system is being developed. Alignment of the SPECT system—to the linear accelerator (LINAC) coordinate frame and to the coordinate frames of other on-board imaging systems such as cone-beam CT (CBCT)—is essential for target localization and image reconstruction. An alignment method that utilizes line sources and one pinhole projection is proposed and investigated to achieve this goal. Potentially, this method could also be applied to the calibration of the other pinhole SPECT systems. Methods: An alignment model consisting of multiple alignment parameters was developed which maps line sources in three-dimensional (3D) space to their two-dimensional (2D) projections on the SPECT detector. In a computer-simulation study, 3D coordinates of line-sources were defined in a reference room coordinate frame, such as the LINAC coordinate frame. Corresponding 2D line-source projections were generated by computer simulation that included SPECT blurring and noise effects. The Radon transform was utilized to detect angles (α) and offsets (ρ) of the line-source projections. Alignment parameters were then estimated by a nonlinear least squares method, based on the α and ρ values and the alignment model. Alignment performance was evaluated as a function of number of line sources, Radon transform accuracy, finite line-source width, intrinsic camera resolution, Poisson noise, and acquisition geometry. Experimental evaluations were performed using a physical line-source phantom and a pinhole-collimated gamma camera attached to a robot. Results: In computer-simulation studies, when there was no error in determining angles (α) and offsets (ρ) of the measured projections, six alignment parameters (three translational and three rotational) were estimated perfectly using three line sources. When angles (α) and offsets (ρ) were provided by the Radon transform, estimation accuracy was reduced. The estimation error was associated with rounding errors of Radon transform, finite line-source width, Poisson noise, number of line sources, intrinsic camera resolution, and detector acquisition geometry. Statistically, the estimation accuracy was significantly improved by using four line sources rather than three and by thinner line-source projections (obtained by better intrinsic detector resolution). With five line sources, median errors were 0.2 mm for the detector translations, 0.7 mm for the detector radius of rotation, and less than 0.5° for detector rotation, tilt, and twist. In experimental evaluations, average errors relative to a different, independent registration technique were about 1.8 mm for detector translations, 1.1 mm for the detector radius of rotation (ROR), 0.5° and 0.4° for detector rotation and tilt, respectively, and 1.2° for detector twist. Conclusions: Alignment parameters can be estimated using one pinhole projection of line sources. Alignment errors are largely associated with limited accuracy of the Radon transform in determining angles (α) and offsets (ρ) of the line-source projections. This alignment method may be important for multipinhole SPECT, where relative pinhole alignment may vary during rotation. For pinhole and multipinhole SPECT imaging on-board radiation therapy machines, the method could provide alignment of SPECT coordinates with those of CBCT and the LINAC. PMID:24320537

A line-source method for aligning on-board and other pinhole SPECT systems.

PubMed

Yan, Susu; Bowsher, James; Yin, Fang-Fang

2013-12-01

In order to achieve functional and molecular imaging as patients are in position for radiation therapy, a robotic multipinhole SPECT system is being developed. Alignment of the SPECT system-to the linear accelerator (LINAC) coordinate frame and to the coordinate frames of other on-board imaging systems such as cone-beam CT (CBCT)-is essential for target localization and image reconstruction. An alignment method that utilizes line sources and one pinhole projection is proposed and investigated to achieve this goal. Potentially, this method could also be applied to the calibration of the other pinhole SPECT systems. An alignment model consisting of multiple alignment parameters was developed which maps line sources in three-dimensional (3D) space to their two-dimensional (2D) projections on the SPECT detector. In a computer-simulation study, 3D coordinates of line-sources were defined in a reference room coordinate frame, such as the LINAC coordinate frame. Corresponding 2D line-source projections were generated by computer simulation that included SPECT blurring and noise effects. The Radon transform was utilized to detect angles (α) and offsets (ρ) of the line-source projections. Alignment parameters were then estimated by a nonlinear least squares method, based on the α and ρ values and the alignment model. Alignment performance was evaluated as a function of number of line sources, Radon transform accuracy, finite line-source width, intrinsic camera resolution, Poisson noise, and acquisition geometry. Experimental evaluations were performed using a physical line-source phantom and a pinhole-collimated gamma camera attached to a robot. In computer-simulation studies, when there was no error in determining angles (α) and offsets (ρ) of the measured projections, six alignment parameters (three translational and three rotational) were estimated perfectly using three line sources. When angles (α) and offsets (ρ) were provided by the Radon transform, estimation accuracy was reduced. The estimation error was associated with rounding errors of Radon transform, finite line-source width, Poisson noise, number of line sources, intrinsic camera resolution, and detector acquisition geometry. Statistically, the estimation accuracy was significantly improved by using four line sources rather than three and by thinner line-source projections (obtained by better intrinsic detector resolution). With five line sources, median errors were 0.2 mm for the detector translations, 0.7 mm for the detector radius of rotation, and less than 0.5° for detector rotation, tilt, and twist. In experimental evaluations, average errors relative to a different, independent registration technique were about 1.8 mm for detector translations, 1.1 mm for the detector radius of rotation (ROR), 0.5° and 0.4° for detector rotation and tilt, respectively, and 1.2° for detector twist. Alignment parameters can be estimated using one pinhole projection of line sources. Alignment errors are largely associated with limited accuracy of the Radon transform in determining angles (α) and offsets (ρ) of the line-source projections. This alignment method may be important for multipinhole SPECT, where relative pinhole alignment may vary during rotation. For pinhole and multipinhole SPECT imaging on-board radiation therapy machines, the method could provide alignment of SPECT coordinates with those of CBCT and the LINAC.

The effect of noise and lipid signals on determination of Gaussian and non-Gaussian diffusion parameters in skeletal muscle.

PubMed

Cameron, Donnie; Bouhrara, Mustapha; Reiter, David A; Fishbein, Kenneth W; Choi, Seongjin; Bergeron, Christopher M; Ferrucci, Luigi; Spencer, Richard G

2017-07-01

This work characterizes the effect of lipid and noise signals on muscle diffusion parameter estimation in several conventional and non-Gaussian models, the ultimate objectives being to characterize popular fat suppression approaches for human muscle diffusion studies, to provide simulations to inform experimental work and to report normative non-Gaussian parameter values. The models investigated in this work were the Gaussian monoexponential and intravoxel incoherent motion (IVIM) models, and the non-Gaussian kurtosis and stretched exponential models. These were evaluated via simulations, and in vitro and in vivo experiments. Simulations were performed using literature input values, modeling fat contamination as an additive baseline to data, whereas phantom studies used a phantom containing aliphatic and olefinic fats and muscle-like gel. Human imaging was performed in the hamstring muscles of 10 volunteers. Diffusion-weighted imaging was applied with spectral attenuated inversion recovery (SPAIR), slice-select gradient reversal and water-specific excitation fat suppression, alone and in combination. Measurement bias (accuracy) and dispersion (precision) were evaluated, together with intra- and inter-scan repeatability. Simulations indicated that noise in magnitude images resulted in <6% bias in diffusion coefficients and non-Gaussian parameters (α, K), whereas baseline fitting minimized fat bias for all models, except IVIM. In vivo, popular SPAIR fat suppression proved inadequate for accurate parameter estimation, producing non-physiological parameter estimates without baseline fitting and large biases when it was used. Combining all three fat suppression techniques and fitting data with a baseline offset gave the best results of all the methods studied for both Gaussian diffusion and, overall, for non-Gaussian diffusion. It produced consistent parameter estimates for all models, except IVIM, and highlighted non-Gaussian behavior perpendicular to muscle fibers (α ~ 0.95, K ~ 3.1). These results show that effective fat suppression is crucial for accurate measurement of non-Gaussian diffusion parameters, and will be an essential component of quantitative studies of human muscle quality. Published 2017. This article is a U.S. Government work and is in the public domain in the USA.

Offsets and conservation of the species of the EU habitats and birds directives.

PubMed

Regnery, Baptiste; Couvet, Denis; Kerbiriou, Christian

2013-12-01

Biodiversity offsets are intended to achieve no net loss of biodiversity due to economic and human development. A variety of biodiversity components are addressed by offset policies. It is required that loss of protected species due to development be offset under the EU Habitats and Birds Directives in Europe. We call this type of offset a species-equality offset because the offset pertains to the same species affected by the development project. Whether species equality can be achieved by offset design is unknown. We addressed this gap by reviewing derogation files (i.e., specific files that describe mitigation measures to ensure no net loss under the EU Habitats and Birds Directives) from 85 development projects in France (2009-2010). We collected information on type of effect (reversible vs. irreversible) and characteristics of affected and offset sites (i.e., types of species, total area). We analyzed how the type of effect and the affected-site characteristics influenced the occurrence of offset measures. The proportion of species targeted by offset measures (i.e., offset species) increased with the irreversibility of the effect of development and the conservation status of the species affected by development (i.e., affected species). Not all effects on endangered species (International Union for Conservation of Nature Red List) were offset; on average, 82% of affected species would be offset. Twenty-six percent of species of least concern were offset species. Thirty-five percent of development projects considered all affected species in their offset measures. Species richness was much lower in offset sites than in developed sites even after offset proposals. For developed areas where species richness was relatively high before development, species richness at offset sites was 5-10 times lower. The species-equality principle appears to have been applied only partially in offset policies, as in the EU directives. We suggest the application of this principle through offsets is highly important for the long-term conservation of biodiversity in Europe. Compensaciones y Conservación de las Especies de las Directivas de Hábitats y Aves de la UE. © 2013 Society for Conservation Biology.

Effectiveness of cable barriers, guardrails, and concrete barrier walls in reducing the risk of injury.

PubMed

Zou, Yaotian; Tarko, Andrew P; Chen, Erdong; Romero, Mario A

2014-11-01

Roadway departure crashes tend to be severe, especially when the roadside exposes the occupants of errant vehicles to excessive injury hazards. As a cost-effective method when the clear zone width is insufficient, road barriers are often installed to prevent errant vehicles from colliding with dangerous obstacles or traversing steep slopes. This paper focuses on the safety performance of road barriers in Indiana in reducing the risk of injury. The objective of the study presented here is to compare the risk of injury among different hazardous events faced by an occupant in a single-vehicle crash. The studied hazardous events include rolling over, striking three types of barriers (guardrails, concrete barrier walls, and cable barriers) with different barrier offsets to the edge of the travelled way, and striking various roadside objects. A total of 2124 single-vehicle crashes (3257 occupants) that occurred between 2008 and 2012 on 517 pair-matched homogeneous barrier and non-barrier segments were analyzed. A binary logistic regression model with mixed effects was estimated for vehicle occupants. The segment pairing process and the use of random effects were able to handle the commonality within the same segment pair as well as the heterogeneity across segment pairs. The modeling results revealed that hitting a barrier is associated with lower risk of injury than a high-hazard event (hitting a pole, rollover, etc.). The odds of injury are reduced by 39% for median concrete barrier walls offset 15-18ft from the travelled way, reduced by 65% for a guardrail face offset 5-55ft, reduced by 85% for near-side median cable barriers (offset between 10ft and 29ft), and reduced by 78% with far-side median cable barriers (offset at least 30ft). Comparing different types of barriers is useful where some types of barriers can be used alternatively. This study found that the odds of injury are 43% lower when striking a guardrail instead of a median concrete barrier offset 15-18ft and 65% lower when striking a median concrete barrier offset 7-14ft. The odds of injury when striking a near-side median cable barrier is 57% lower than the odds for a guardrail face. This reduction for a far side median cable barrier is 37%. Thus, a guardrail should be preferred over a concrete wall and a cable barrier should be preferred over a guardrail where the road and traffic conditions allow. In the light of the results, installing median cable barriers on both sides of the median to reduce their lateral offset is beneficial for safety. The study also found that the unexplained heterogeneity across vehicles is much larger than it was across matched segment pairs. Copyright © 2014 Elsevier Ltd. All rights reserved.

Home visiting programmes for the prevention of child maltreatment: cost-effectiveness of 33 programmes.

PubMed

Dalziel, Kim; Segal, Leonie

2012-09-01

There is a body of published research on the effectiveness of home visiting for the prevention of child maltreatment, but little in the peer reviewed literature on cost-effectiveness or value to society. The authors sought to determine the cost-effectiveness of alternative home visiting programmes to inform policy. All trials reporting child maltreatment outcomes were identified through systematic review. Information on programme effectiveness and components were taken from identified studies, to which 2010 Australian unit costs were applied. Lifetime cost offsets associated with maltreatment were derived from a recent Australian study. Cost-effectiveness results were estimated as programme cost per case of maltreatment prevented and net benefit estimated by incorporating downstream cost savings. Sensitivity analyses were conducted. 33 home visiting programmes were evaluated and cost-effectiveness estimates derived for the 25 programmes not dominated. The incremental cost of home visiting compared to usual care ranged from A$1800 to A$30 000 (US$1800-US$30 000) per family. Cost-effectiveness estimates ranged from A$22 000 per case of maltreatment prevented to several million. Seven of the 22 programmes (32%) of at least adequate quality were cost saving when including lifetime cost offsets. There is great variation in the cost-effectiveness of home visiting programmes for the prevention of maltreatment. The most cost-effective programmes use professional home visitors in a multi-disciplinary team, target high risk populations and include more than just home visiting. Home visiting programmes must be carefully selected and well targeted if net social benefits are to be realised.

A lumped mucosal wave model of the vocal folds revisited: Recent extensions and oscillation hysteresis

PubMed Central

Lucero, Jorge C.; Koenig, Laura L.; Lourenço, Kelem G.; Ruty, Nicolas; Pelorson, Xavier

2011-01-01

This paper examines an updated version of a lumped mucosal wave model of the vocal fold oscillation during phonation. Threshold values of the subglottal pressure and the mean (DC) glottal airflow for the oscillation onset are determined. Depending on the nonlinear characteristics of the model, an oscillation hysteresis phenomenon may occur, with different values for the oscillation onset and offset threshold. The threshold values depend on the oscillation frequency, but the occurrence of the hysteresis is independent of it. The results are tested against pressure data collected from a mechanical replica of the vocal folds, and oral airflow data collected from speakers producing intervocalic ∕h∕. In the human speech data, observed differences between voice onset and offset may be attributed to variations in voice pitch, with a very small or inexistent hysteresis phenomenon. PMID:21428520

Symmetric voltage-controlled variable resistance

NASA Technical Reports Server (NTRS)

Vanelli, J. C.

1978-01-01

Feedback network makes resistance of field-effect transistor (FET) same for current flowing in either direction. It combines control voltage with source and load voltages to give symmetric current/voltage characteristics. Since circuit produces same magnitude output voltage for current flowing in either direction, it introduces no offset in presense of altering polarity signals. It is therefore ideal for sensor and effector circuits in servocontrol systems.

Trends and Challenges in Aerospace Offsets: Proceedings and Papers,

DTIC Science & Technology

1999-01-01

nancing, license production and co-production agreements, subcontractor pro- duction, countertrade , foreign investment, and labor adjustment...34 countertrade ," and they are similarly ineffi- cient and trade distorting from an economic perspective. By substituting various forms of barter for...U.S. or European producers because of severe financial constraints of prospective customers and a consequently high reliance on countertrade . But

A Tale of Two Limpets (Patella vulgata and Patella stellaeformis): Evaluating a New Proxy for Late Holocene Climate Change in Coastal Areas

NASA Astrophysics Data System (ADS)

Fenger, T. L.; Surge, D. M.; Schoene, B. R.; Carter, J. G.; Milner, N.

2006-12-01

Shells of the European limpet, Patella vulgata, from Late Holocene archaeological deposits potentially contain critical information about climate change in coastal areas. Before deciphering climate information preserved in these zooarchaeological records, we studied the controls on oxygen isotope ratios (δ18O) in modern specimens. We tested the hypothesis that P. vulgata precipitates its shell in isotopic equilibrium with ambient water by comparing δ18OSHELL with expected values. Expected δ18OSHELL was constructed using the calcite-water fractionation equation, observed sea surface temperature (SST), and assuming δ18OWATER is +0.10‰ (VSMOW). Comparison between expected and measured δ18OSHELL revealed a +1.51±0.21‰ (VPDB) offset from expected values. Consequently, estimated SST calculated from δ18OSHELL was 6.50±2.45°C lower than observed SST. However, because the offset was relatively uniform, an adjustment can be made to account for this predictable vital effect and past SST can be reliably reconstructed. To further investigate the source of offset in this genus, we analyzed a fully marine tropical species (Patella stellaeformis) to minimize seasonal variation in environmental factors that influence δ18OSHELL. P. stellaeformis was evaluated to determine whether it has a similar offset from equilibrium as P. vulgata. We tested the hypotheses that: (1) δ18OSHELL in tropical species also displays vital effects; and (2) the offset from equilibrium (if any) would be constant and predictable. Our results indicated: (1) aragonite comprises most of P. stellaeformis' shell; and (2) δ18OSHELL is statistically indistinguishable from expected values calculated using the aragonite-water fractionation equation (Kolmogorov-Smirnov test statistic=0.61, D0.05[56, 57]=1.36) in contrast with our observations in P. vulgata. Differences in mineralogy or growth rates at different latitudes may play a role in mechanisms that influence vital effects.

Building a high resolution national elevation model from SRTM: The Australian experience

NASA Astrophysics Data System (ADS)

Gallant, J. C.; Read, A.; Dowling, T. I.

2011-12-01

The global SRTM DEM is a valuable global data set that, for many countries including Australia, provides the best basis for a fine resolution national DEM. But the SRTM data suffers from a variety of artefacts and errors that prevent its routine application with familiar terrain analysis tools. The most important of these are stripes, voids, random noise and offsets due to trees. The tree offsets are particularly disruptive in riparian areas where they make rivers appear as ridge lines. This paper describes how a suite of tools was applied to the 1 second SRTM data for Australia to treat each of these artefacts. An FFT-based tool was developed to detect and remove regular striping. Voids were filled using a modification of the delta surface fill method. Offsets due to trees were modelled and removed using a vegetation mask derived from remotely sensed imagery and a statistical estimate of the offset at vegetation patch boundaries. Random noise was removed using an adaptive smoothing method that responds to variations in both local relief and noise magnitude. Finally, mapped channel networks were imposed using a modified version of the ANUDEM software to enforce hydrological connectivity. The resulting products are being distributed by Geoscience Australia and the smoothed and drainage enforced products in particular are suitable for use in routine terrain analysis tasks. With some adaptation, the same processes could be applied to the global SRTM to derive a product that, in combination with an improved ASTER G-DEM, would provide a high quality comprehensive global elevation model suitable for most purposes.

Control of Ge1-x-ySixSny layer lattice constant for energy band alignment in Ge1-xSnx/Ge1-x-ySixSny heterostructures

NASA Astrophysics Data System (ADS)

Fukuda, Masahiro; Watanabe, Kazuhiro; Sakashita, Mitsuo; Kurosawa, Masashi; Nakatsuka, Osamu; Zaima, Shigeaki

2017-10-01

The energy band alignment of Ge1-xSnx/Ge1-x-ySixSny heterostructures was investigated, and control of the valence band offset at the Ge1-xSnx/Ge1-x-ySixSny heterointerface was achieved by controlling the Si and Sn contents in the Ge1-x-ySixSny layer. The valence band offset in the Ge0.902Sn0.098/Ge0.41Si0.50Sn0.09 heterostructure was evaluated to be as high as 330 meV, and its conduction band offset was estimated to be 150 meV by considering the energy bandgap calculated from the theoretical prediction. In addition, the formation of the strain-relaxed Ge1-x-ySixSny layer was examined and the crystalline structure was characterized. The epitaxial growth of a strain-relaxed Ge0.64Si0.21Sn0.15 layer with the degree of strain relaxation of 55% was examined using a virtual Ge substrate. Moreover, enhancement of the strain relaxation was demonstrated by post-deposition annealing, where a degree of strain relaxation of 70% was achieved after annealing at 400 °C. These results indicate the possibility for enhancing the indirect-direct crossover with a strained and high-Sn-content Ge1-xSnx layer on a strain-relaxed Ge1-x-ySixSny layer, realizing preferable carrier confinement by type-I energy band alignment with high conduction and valence band offsets.

Segmentation Control on Crustal Accretion: Insights From the Chile Ridge

NASA Astrophysics Data System (ADS)

Martinez, F.; Karsten, J. L.; Milman, M. S.; Klein, E. M.

2002-12-01

Controls on crustal accretion at mid-ocean ridges include spreading rate and mantle temperature and composition. Less studied is the effect of the segmentation geometry, although it has been known for some time that large offset transforms have significant effects on the extent of melting and lava compositions produced by ridges in their vicinity. The PANORAMA 4 expedition surveyed the Chile Ridge between 36°-43°S in order to examine the effects of ridge segmentation on crustal accretion. This section of the ridge is spreading uniformly at intermediate rates (~53 mm/yr) and rock sampling and regional data indicate a largely uniform mantle composition with no systematic changes in mantle thermal structure. Thus the segmentation geometry is the primary crustal accretion variable. The survey mapped and sampled 19 first order ridge segments and their transform offsets. The ridges range from 130 to 10 km in length with mapped transform offsets from 168 to 19 km. The segments primarily have axial valley morphology, with segments longer than ~65 km typically displaying central highs deepening toward segment ends. Mantle Bouguer anomalies (MBAs) show that these segments also have bulls eye lows associated with the central highs indicating thicker crust than at segment ends. Overall the mapped segments displays a trend of increasing depth and MBA, implying diminishing crustal production, with decreasing segment length and increasing transform offset. We examine the cause of this trend by modeling the mantle flow pattern generated by finite length ridge segments using the Phipps-Morgan and Forsyth (1988) algorithm. The results indicate that at a constant spreading rate mantle upwelling rates are greatest and extend deeper near the segment center, and that for segments that are significantly offset, upwelling rates decrease overall with decreasing segment length. The modeling implies that segmentation itself, even without cooling and lithospheric relief at transforms has a strong influence on mantle advection and therefore on crustal production.

Effect of tool offsetting on microstructure and mechanical properties dissimilar friction stir welded Mg-Al alloys

NASA Astrophysics Data System (ADS)

Baghdadi, Amir Hossein; Fazilah Mohamad Selamat, Nor; Sajuri, Zainuddin

2017-09-01

Automotive and aerospace industries are attempting to produce lightweight structure by using materials with low density such as aluminum and magnesium alloys to increase the fuel efficiency and consequently reduce the environmental pollution. It can be beneficial to join Mg to Al to acquire ideal performance in special applications. Friction stir welding (FSW) is solid state welding processes and relatively lower temperature of the process compared to fusion welding processes. This makes FSW a potential joining technique for joining of the dissimilar materials. In this study, Mg-Al butt joints were performed by FSW under different tool offset conditions, rotation rates (500-600 rpm) and traverse speeds (20 mm/min) with tool axis offset 1 mm shifted into AZ31B or Al6061 (T6), and without offset. During the welding process AZ31B was positioned at the advancing side (AS) and Al6061 (T6) was located at the retreating side (RS). Defect free AZ31B-Al6061 (T6) dissimilar metal FSW joints with good mechanical properties were obtained with the combination of intermediate rotation rate and low traverse speed pin is in the middle. When tool positioned in -1 mm or +1 mm offsetting, some defects were found in SZ of dissimilar FSWed joints such as cavity, tunnel, and crack. Furthermore, a thin layer of intermetallic compounds was observed in the stir zone at the interface between Mg-Al plates. The strength of the joint was influenced by FSW parameters. Good mechanical properties obtained with the combination of intermediate rotational speed of 600 rpm and low travelling speed of 20 mm/min by locating Mg on advancing side when pin is in the middle. Also, Joint efficiency of the welds prepared in the present study was between 29% and 68% for the different welding parameters.

The Width of a Solar Coronal Mass Ejection and the Source of the Driving Magnetic Explosion

NASA Technical Reports Server (NTRS)

Moore, Ronald L.; Sterling, Alphonse C.; Suess, Steven T.

2007-01-01

We show that the strength of the magnetic field in the area covered by the flare arcade following a CME-producing ejective solar eruption can be estimated from the final angular width of the CME in the outer corona and the final angular width of the flare arcade. We assume (1) the flux-rope plasmoid ejected from the flare site becomes the interior of the CME plasmoid, (2) in the outer corona (R greater than 2R(sub Sun)) the CME is roughly a spherical plasmoid with legs shaped like a light bulb, and (3) beyond some height in or below the outer corona the CME plasmoid is in lateral pressure balance with the surrounding magnetic field. The strength of the nearly radial magnetic field in the outer corona is estimated from the radial component of the interplanetary magnetic field measured by Ulysses. We apply this model to three well-observed CMEs that exploded from flare regions of extremely different size and magnetic setting. One of these CMEs is an over-and-out CME that exploded from a laterally far offset compact ejective flare. In each event, the estimated source-region field strength is appropriate for the magnetic setting of the flare. This agreement (1) indicates that CMEs are propelled by the magnetic field of the CME plasmoid pushing against the surrounding magnetic field, (2) supports the magnetic-arch-blowout scenario for over-and-out CMEs, and (3) shows that a CME s final angular width in the outer corona can be estimated from the amount of magnetic flux covered by the source-region flare arcade.

Slowdown of N2O emissions from China's croplands

NASA Astrophysics Data System (ADS)

Zhou, F.; Shang, Z.; Ciais, P.; Piao, S.; Tian, H.; Saikawa, E.; Zaehle, S.; Del Grosso, S. J.; Galloway, J. N.

2016-12-01

To feed the increasing population, China has experienced a rapid agricultural development over past decades, accompanied by increased fertilizer consumptions in croplands, but the magnitude, trend, and causes of the associated nitrous oxide (N2O) emissions has remain unclear. The primary sources of this uncertainty are conflicting estimates of fertilizer consumption and emission factors, the latter being uncertain because of very few regional representativeness of the Nrate-flux relationships in China. Here we re-estimate China's N2O emissions from croplands using three different methods: flux upscaling technique, process-based models and atmospheric inversion, and also analyze the corresponding drivers using an attribution approach. The three methods produce similar estimates of N2O emissions in the range of 0.67 ± 0.08 to 0.62± 0.11 Tg nitrogen per year, which is 29% larger than the estimates by the Emission Database for Global Atmospheric Research (EDGAR) that is adopted by Intergovernmental Panel on Climate Change (IPCC) as the emission baseline and twofold larger than the latest Chinese national report submitted to the United Nations Framework Convention on Climate Change, but the revised trend slows down after 2005. Fertilizer N application per area is the dominant factor driving the increase in N2O emissions across most cropping regions from 1990 to 2004, but climate-induced change of emission factors has also controlled N2O flux from 2005 onwards. Our findings suggest that, as precipitation would increase in North China but decline in the South in future, EF will increasingly control China's agri. soil emissions of N2O, unless offset by larger reductions of fertilizer consumptions.

Cost effectiveness of converting to alternative motor vehicle fuels. A technical assistance study for the City of Longview

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCoy, G.A.

1983-11-18

The City of Longview can obtain significant fuel savings benefits by converting a portion of their vehicle fleet to operate on either compressed natural gas (CNG) or liquid petroleum gas (LPG) fuels. The conversion of 41 vehicles including police units, sedans, pickups, and light duty trucks to CNG use would offset approximately 47% of the city's 1982 gasoline consumption. The CNG conversion capital outlay of $115,000 would be recovered through fuel cost reductions. The Cascade Natural Gas Corporation sells natural gas under an interruptible tariff for $0.505 per therm, equivalent to slightly less than one gallon of gasoline. The citymore » currently purchases unleaded gasoline at $1.115 per gallon. A payback analysis indicates that 39.6 months are required for the CNG fuel savings benefits to offset the initial or first costs of the conversion. The conversion of fleet vehicles to liquid petroleum gas (LPG) or propane produces comparable savings in vehicle operating costs. The conversion of 59 vehicles including police units, pickup and one ton trucks, street sweepers, and five cubic yard dump trucks would cost approximately $59,900. The annual purchase of 107,000 gallons of propane would offset the consumption of 96,300 gallons of gasoline, or approximately 67% of the city's 1982 usage. Propane is currently retailing for $0.68 to $0.74 per gallon. A payback analysis indicates that 27.7 months are required for the fuel savings benefits to offset the initial LPG conversion costs.« less

Photon caliper to achieve submillimeter positioning accuracy

NASA Astrophysics Data System (ADS)

Gallagher, Kyle J.; Wong, Jennifer; Zhang, Junan

2017-09-01

The purpose of this study was to demonstrate the feasibility of using a commercial two-dimensional (2D) detector array with an inherent detector spacing of 5 mm to achieve submillimeter accuracy in localizing the radiation isocenter. This was accomplished by delivering the Vernier ‘dose’ caliper to a 2D detector array where the nominal scale was the 2D detector array and the non-nominal Vernier scale was the radiation dose strips produced by the high-definition (HD) multileaf collimators (MLCs) of the linear accelerator. Because the HD MLC sequence was similar to the picket fence test, we called this procedure the Vernier picket fence (VPF) test. We confirmed the accuracy of the VPF test by offsetting the HD MLC bank by known increments and comparing the known offset with the VPF test result. The VPF test was able to determine the known offset within 0.02 mm. We also cross-validated the accuracy of the VPF test in an evaluation of couch hysteresis. This was done by using both the VPF test and the ExacTrac optical tracking system to evaluate the couch position. We showed that the VPF test was in agreement with the ExacTrac optical tracking system within a root-mean-square value of 0.07 mm for both the lateral and longitudinal directions. In conclusion, we demonstrated the VPF test can determine the offset between a 2D detector array and the radiation isocenter with submillimeter accuracy. Until now, no method to locate the radiation isocenter using a 2D detector array has been able to achieve such accuracy.

Improving HybrID: How to best combine indirect and direct encoding in evolutionary algorithms.

PubMed

Helms, Lucas; Clune, Jeff

2017-01-01

Many challenging engineering problems are regular, meaning solutions to one part of a problem can be reused to solve other parts. Evolutionary algorithms with indirect encoding perform better on regular problems because they reuse genomic information to create regular phenotypes. However, on problems that are mostly regular, but contain some irregularities, which describes most real-world problems, indirect encodings struggle to handle the irregularities, hurting performance. Direct encodings are better at producing irregular phenotypes, but cannot exploit regularity. An algorithm called HybrID combines the best of both: it first evolves with indirect encoding to exploit problem regularity, then switches to direct encoding to handle problem irregularity. While HybrID has been shown to outperform both indirect and direct encoding, its initial implementation required the manual specification of when to switch from indirect to direct encoding. In this paper, we test two new methods to improve HybrID by eliminating the need to manually specify this parameter. Auto-Switch-HybrID automatically switches from indirect to direct encoding when fitness stagnates. Offset-HybrID simultaneously evolves an indirect encoding with directly encoded offsets, eliminating the need to switch. We compare the original HybrID to these alternatives on three different problems with adjustable regularity. The results show that both Auto-Switch-HybrID and Offset-HybrID outperform the original HybrID on different types of problems, and thus offer more tools for researchers to solve challenging problems. The Offset-HybrID algorithm is particularly interesting because it suggests a path forward for automatically and simultaneously combining the best traits of indirect and direct encoding.

Tsunami Amplitude Estimation from Real-Time GNSS.

NASA Astrophysics Data System (ADS)

Jeffries, C.; MacInnes, B. T.; Melbourne, T. I.

2017-12-01

Tsunami early warning systems currently comprise modeling of observations from the global seismic network, deep-ocean DART buoys, and a global distribution of tide gauges. While these tools work well for tsunamis traveling teleseismic distances, saturation of seismic magnitude estimation in the near field can result in significant underestimation of tsunami excitation for local warning. Moreover, DART buoy and tide gauge observations cannot be used to rectify the underestimation in the available time, typically 10-20 minutes, before local runup occurs. Real-time GNSS measurements of coseismic offsets may be used to estimate finite faulting within 1-2 minutes and, in turn, tsunami excitation for local warning purposes. We describe here a tsunami amplitude estimation algorithm; implemented for the Cascadia subduction zone, that uses continuous GNSS position streams to estimate finite faulting. The system is based on a time-domain convolution of fault slip that uses a pre-computed catalog of hydrodynamic Green's functions generated with the GeoClaw shallow-water wave simulation software and maps seismic slip along each section of the fault to points located off the Cascadia coast in 20m of water depth and relies on the principle of the linearity in tsunami wave propagation. The system draws continuous slip estimates from a message broker, convolves the slip with appropriate Green's functions which are then superimposed to produce wave amplitude at each coastal location. The maximum amplitude and its arrival time are then passed into a database for subsequent monitoring and display. We plan on testing this system using a suite of synthetic earthquakes calculated for Cascadia whose ground motions are simulated at 500 existing Cascadia GPS sites, as well as real earthquakes for which we have continuous GNSS time series and surveyed runup heights, including Maule, Chile 2010 and Tohoku, Japan 2011. This system has been implemented in the CWU Geodesy Lab for the Cascadia subduction zone but will be expanded to the circum-Pacific as real-time processing of international GNSS data streams become available.

Femoral offset: anatomical concept, definition, assessment, implications for preoperative templating and hip arthroplasty.

PubMed

Lecerf, G; Fessy, M H; Philippot, R; Massin, P; Giraud, F; Flecher, X; Girard, J; Mertl, P; Marchetti, E; Stindel, E

2009-05-01

BACKGROUND OBJECTIVE: Femoral offset is supposed to influence the results of hip replacement but little is known about the accurate method of measure and the true effect of offset modifications. This article is a collection of independent anatomic, radiological and clinical works, which purpose is to assess knowledge of the implications of femoral offset for preoperative templating and total hip arthroplasty. There is a strong correlation between femoral offset, abductors lever arm and hip abductor strength. Hip lateralization is independent of the femoral endomedullary characteristics. The abductors lever arm is highly correlated to the gluteus medius activation angle. There were correlations between femoral offset and endomedullary shape. The hip center was high and medial for stovepipe metaphysis while it was lower and lateralized for champagne - flute upper femur. A study was performed to compare the femoral offset measured by X-ray and CT-scan in 50 patients, demonstrated that plain radiography underestimates offset measurement. The 2D templating cannot appreciate the rotation of the lower limb. Taking into account the horizontal plane is essential to obtain proper 3D planning of the femoral offset. A randomized study was designed to compare femoral offset measurements after hip resurfacing and total hip arthroplasty. This study underlined hip resurfacing reduced the femoral offset, while hip replacement increased offset. However, the reduction of femoral offset after hip resurfacing does not affect the function. A pilot study was designed to assess the results of 120 hip arthroplasties with a modular femoral neck. This study showed that the use of a modular collar ensures an easier restoration of the femoral offset. A cohort of high offset stems (Lubinus 117 degrees) was retrospectively assessed. The survival rate was slightly lower that the standard design reported in the Swedish register. Finally, the measurement of offset and leg length was assessed with the help of computer assistance. The software changed the initial schedule (obtained by templating) in 29%. Therefore, femoral offset restoration is essential to improve function and longevity of hip arthroplasty. CT-scan is more accurate than plain radiography to assess femoral offset. Hip resurfacing decreases offset without effect on function. Modular neck and computer assistance may improve intraoperative calculation and reproduction of femoral offset. Increasing offset with a standard cemented design may decrease long-term fixation. Level IV: Retrospective or historical series.

Synthetic biology for microbial production of lipid-based biofuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

d’Espaux, Leo; Mendez-Perez, Daniel; Li, Rachel

The risks of maintaining current CO 2 emission trends have led to interest in producing biofuels using engineered microbes. Microbial biofuels reduce emissions because CO 2 produced by fuel combustion is offset by CO2 captured by growing biomass, which is later used as feedstock for biofuel fermentation. Hydrocarbons found in petroleum fuels share striking similarity with biological lipids. Here in this paper we review synthetic metabolic pathways based on fatty acid and isoprenoid metabolism to produce alkanes and other molecules suitable as biofuels. Lastly, we further discuss engineering strategies to optimize engineered biosynthetic routes, as well as the potential ofmore » synthetic biology for sustainable manufacturing.« less

Assessing Earthquake-Induced Tree Mortality in Temperate Forest Ecosystems: A Case Study from Wenchuan, China

DOE PAGES

Zeng, Hongcheng; Lu, Tao; Jenkins, Hillary; ...

2016-03-17

Earthquakes can produce significant tree mortality, and consequently affect regional carbon dynamics. Unfortunately, detailed studies quantifying the influence of earthquake on forest mortality are currently rare. The committed forest biomass carbon loss associated with the 2008 Wenchuan earthquake in China is assessed by a synthetic approach in this study that integrated field investigation, remote sensing analysis, empirical models and Monte Carlo simulation. The newly developed approach significantly improved the forest disturbance evaluation by quantitatively defining the earthquake impact boundary and detailed field survey to validate the mortality models. Based on our approach, a total biomass carbon of 10.9 Tg·C wasmore » lost in Wenchuan earthquake, which offset 0.23% of the living biomass carbon stock in Chinese forests. Tree mortality was highly clustered at epicenter, and declined rapidly with distance away from the fault zone. It is suggested that earthquakes represent a signif icant driver to forest carbon dynamics, and the earthquake-induced biomass carbon loss should be included in estimating forest carbon budgets.« less

Invited Article: Electric solar wind sail: Toward test missions

NASA Astrophysics Data System (ADS)

Janhunen, P.; Toivanen, P. K.; Polkko, J.; Merikallio, S.; Salminen, P.; Haeggström, E.; Seppänen, H.; Kurppa, R.; Ukkonen, J.; Kiprich, S.; Thornell, G.; Kratz, H.; Richter, L.; Krömer, O.; Rosta, R.; Noorma, M.; Envall, J.; Lätt, S.; Mengali, G.; Quarta, A. A.; Koivisto, H.; Tarvainen, O.; Kalvas, T.; Kauppinen, J.; Nuottajärvi, A.; Obraztsov, A.

2010-11-01

The electric solar wind sail (E-sail) is a space propulsion concept that uses the natural solar wind dynamic pressure for producing spacecraft thrust. In its baseline form, the E-sail consists of a number of long, thin, conducting, and centrifugally stretched tethers, which are kept in a high positive potential by an onboard electron gun. The concept gains its efficiency from the fact that the effective sail area, i.e., the potential structure of the tethers, can be millions of times larger than the physical area of the thin tethers wires, which offsets the fact that the dynamic pressure of the solar wind is very weak. Indeed, according to the most recent published estimates, an E-sail of 1 N thrust and 100 kg mass could be built in the rather near future, providing a revolutionary level of propulsive performance (specific acceleration) for travel in the solar system. Here we give a review of the ongoing technical development work of the E-sail, covering tether construction, overall mechanical design alternatives, guidance and navigation strategies, and dynamical and orbital simulations.

Invited article: Electric solar wind sail: toward test missions.

PubMed

Janhunen, P; Toivanen, P K; Polkko, J; Merikallio, S; Salminen, P; Haeggström, E; Seppänen, H; Kurppa, R; Ukkonen, J; Kiprich, S; Thornell, G; Kratz, H; Richter, L; Krömer, O; Rosta, R; Noorma, M; Envall, J; Lätt, S; Mengali, G; Quarta, A A; Koivisto, H; Tarvainen, O; Kalvas, T; Kauppinen, J; Nuottajärvi, A; Obraztsov, A

2010-11-01

The electric solar wind sail (E-sail) is a space propulsion concept that uses the natural solar wind dynamic pressure for producing spacecraft thrust. In its baseline form, the E-sail consists of a number of long, thin, conducting, and centrifugally stretched tethers, which are kept in a high positive potential by an onboard electron gun. The concept gains its efficiency from the fact that the effective sail area, i.e., the potential structure of the tethers, can be millions of times larger than the physical area of the thin tethers wires, which offsets the fact that the dynamic pressure of the solar wind is very weak. Indeed, according to the most recent published estimates, an E-sail of 1 N thrust and 100 kg mass could be built in the rather near future, providing a revolutionary level of propulsive performance (specific acceleration) for travel in the solar system. Here we give a review of the ongoing technical development work of the E-sail, covering tether construction, overall mechanical design alternatives, guidance and navigation strategies, and dynamical and orbital simulations.

A revised lens time delay for JVAS B0218+357 from a reanalysis of VLA monitoring data

NASA Astrophysics Data System (ADS)

Biggs, A. D.; Browne, I. W. A.

2018-06-01

We have reanalysed the 1996/1997 Very Large Array monitoring data of the gravitational lens system JVAS B0218+357 to produce improved total flux density and polarization variability curves at 15, 8.4, and 5 GHz. This has been done using improved calibration techniques, accurate subtraction of the emission from the Einstein ring, and careful correction of various systematic effects, especially an offset in polarization position angle that is hour-angle dependent. The variations in total and polarized flux density give the best constraints and we determine a combined delay estimate of 11.3 ± 0.2 d (1σ). This is consistent with the γ-ray value recently derived using the Fermi Gamma-ray Space Telescope and thus we find no evidence for a positional shift between the radio and γ-ray emitting regions. Combined with the previously published lens model found using LENSCLEAN, the new delay gives a value for the Hubble constant of H0 = 72.9 ± 2.6 km s-1 Mpc-1 (1σ).

The Devils Mountain Fault zone: An active Cascadia upper plate zone of deformation, Pacific Northwest of North America

NASA Astrophysics Data System (ADS)

Barrie, J. Vaughn; Greene, H. Gary

2018-02-01

The Devils Mountain Fault Zone (DMFZ) extends east to west from Washington State to just south of Victoria, British Columbia, in the northern Strait of Juan de Fuca of Canada and the USA. Recently collected geophysical data were used to map this fault zone in detail, which show the main fault trace, and associated primary and secondary (conjugate) strands, and extensive northeast-southwest oriented folding that occurs within a 6 km wide deformation zone. The fault zone has been active in the Holocene as seen in the offset and disrupted upper Quaternary strata, seafloor displacement, and deformation within sediment cores taken close to the seafloor expression of the faults. Data suggest that the present DMFZ and the re-activated Leech River Fault may be part of the same fault system. Based on the length and previously estimated slip rates of the fault zone in Washington State, the DMFZ appears to have the potential of producing a strong earthquake, perhaps as large as magnitude 7.5 or greater, within 2 km of the city of Victoria.

Evidence synthesis for medical decision making and the appropriate use of quality scores.

PubMed

Doi, Suhail A R

2014-09-01

Meta-analyses today continue to be run using conventional random-effects models that ignore tangible information from studies such as the quality of the studies involved, despite the expectation that results of better quality studies reflect more valid results. Previous research has suggested that quality scores derived from such quality appraisals are unlikely to be useful in meta-analysis, because they would produce biased estimates of effects that are unlikely to be offset by a variance reduction within the studied models. However, previous discussions took place in the context of such scores viewed in terms of their ability to maximize their association with both the magnitude and direction of bias. In this review, another look is taken at this concept, this time asserting that probabilistic bias quantification is not possible or even required of quality scores when used in meta-analysis for redistribution of weights. The use of such a model is contrasted with the conventional random effects model of meta-analysis to demonstrate why the latter is inadequate in the face of a properly specified quality score weighting method. © 2014 Marshfield Clinic.

Assessing Earthquake-Induced Tree Mortality in Temperate Forest Ecosystems: A Case Study from Wenchuan, China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeng, Hongcheng; Lu, Tao; Jenkins, Hillary

Earthquakes can produce significant tree mortality, and consequently affect regional carbon dynamics. Unfortunately, detailed studies quantifying the influence of earthquake on forest mortality are currently rare. The committed forest biomass carbon loss associated with the 2008 Wenchuan earthquake in China is assessed by a synthetic approach in this study that integrated field investigation, remote sensing analysis, empirical models and Monte Carlo simulation. The newly developed approach significantly improved the forest disturbance evaluation by quantitatively defining the earthquake impact boundary and detailed field survey to validate the mortality models. Based on our approach, a total biomass carbon of 10.9 Tg·C wasmore » lost in Wenchuan earthquake, which offset 0.23% of the living biomass carbon stock in Chinese forests. Tree mortality was highly clustered at epicenter, and declined rapidly with distance away from the fault zone. It is suggested that earthquakes represent a signif icant driver to forest carbon dynamics, and the earthquake-induced biomass carbon loss should be included in estimating forest carbon budgets.« less

Magnetic field gradients inferred from multi-point measurements of Cluster FGM and EDI

NASA Astrophysics Data System (ADS)

Teubenbacher, Robert; Nakamura, Rumi; Giner, Lukas; Plaschke, Ferdinand; Baumjohann, Wolfgang; Magnes, Werner; Eichelberger, Hans; Steller, Manfred; Torbert, Roy

2013-04-01

We use Cluster data from fluxgate magnetometer (FGM) and electron drift instrument (EDI) to determine the magnetic field gradients in the near-Earth magnetotail. Here we use the magnetic field data from FGM measurements as well as the gyro-time data of electrons determined from the time of flight measurements of EDI. The results are compared with the values estimated from empirical magnetic field models for different magnetospheric conditions. We also estimated the spin axis offset of FGM based on comparison between EDI and FGM data and discuss the possible effect in determining the current sheet characteristics.

Complex forest dynamics indicate potential for slowing carbon accumulation in the southeastern United States

Treesearch

John W. Coulston; David N. Wear; James M. Vose

2015-01-01

Over the past century forest regrowth in Europe and North America expanded forest carbon (C) sinks and offset C emissions but future C accumulation is uncertain. Policy makers need insights into forest C dynamics as they anticipate emissions futures and goals. We used land use and forest inventory data to estimate how forest C dynamics have changed in the southeastern...

Geometry of Thrust Faults Beneath Amenthes Rupes, Mars

NASA Technical Reports Server (NTRS)

Vidal, A.; Mueller, K. M.; Golombek, M. P.

2005-01-01

Amenthes Rupes is a 380 km-long lobate fault scarp located in the eastern hemisphere of Mars near the dichotomy boundary. The scarp is marked by about 1 km of vertical separation across a northeast dipping thrust fault (top to the SW) and offsets heavily-cratered terrain of Late Noachian age, the visible portion of which was in place by 3.92 Ga and the buried portion in place between 4.08 and 4.27 Ga. The timing of scarp formation is difficult to closely constrain. Previous geologic mapping shows that near the northern end of Amenthes Rupes, Hesperian age basalts terminate at the scarp, suggesting that fault slip predated the emplacement of these flows at 3.69 to 3.9 Ga. Maxwell and McGill also suggest the faulting ceased before the final emplacement of the Late Hesperian lavas on Isidis Planitia. The trend of the faults at Amenthes, like many thrust faults at the dichotomy boundary, parallels the boundary itself. Schultz and Watters used a dislocation modeling program to match surface topography and vertical offset of the scarp at Amenthes Rupes, varying the dip and depth of faulting, assuming a slip of 1.5 km on the fault. They modeled faulting below Amenthes Rupes as having a dip of between 25 and 30 degrees and a depth of 25 to 35 km, based on the best match to topography. Assuming a 25 degree dip and surface measurements of vertical offset of between 0.3 and 1.2 km, Watters later estimated the maximum displacement on the Amenthes Rupes fault to be 2.90 km. However, these studies did not determine the geometry of the thrust using quantitative constraints that included shortening estimates. Amenthes Rupes deforms large preexisting impact craters. We use these craters to constrain shortening across the scarp and combine this with vertical separation to infer fault geometry. Fault dip was also estimated using measurements of scarp morphology. Measurements were based on 460 m (1/128 per pixel) digital elevation data from the Mars Orbiter Laser Altimeter (MOLA), an instrument on the Mars Global Surveyor (MGS) satellite.

Low-carbon agriculture in South America to mitigate global climate change and advance food security.

PubMed

Sá, João Carlos de Moraes; Lal, Rattan; Cerri, Carlos Clemente; Lorenz, Klaus; Hungria, Mariangela; de Faccio Carvalho, Paulo Cesar

2017-01-01

The worldwide historical carbon (C) losses due to Land Use and Land-Use Change between 1870 and 2014 are estimated at 148 Pg C (1 Pg=1billionton). South America is chosen for this study because its soils contain 10.3% (160 Pg C to 1-m depth) of the soil organic carbon stock of the world soils, it is home to 5.7% (0.419 billion people) of the world population, and accounts for 8.6% of the world food (491milliontons) and 21.0% of meat production (355milliontons of cattle and buffalo). The annual C emissions from fossil fuel combustion and cement production in South America represent only 2.5% (0.25 Pg C) of the total global emissions (9.8 Pg C). However, South America contributes 31.3% (0.34 Pg C) of global annual greenhouse gas emissions (1.1 Pg C) through Land Use and Land Use Change. The potential of South America as a terrestrial C sink for mitigating climate change with adoption of Low-Carbon Agriculture (LCA) strategies based on scenario analysis method is 8.24 Pg C between 2016 and 2050. The annual C offset for 2016 to 2020, 2021 to 2035, and 2036 to 2050 is estimated at 0.08, 0.25, and 0.28 Pg C, respectively, equivalent to offsetting 7.5, 22.2 and 25.2% of the global annual greenhouse gas emissions by Land Use and Land Use Change for each period. Emission offset for LCA activities is estimated at 31.0% by restoration of degraded pasturelands, 25.6% by integrated crop-livestock-forestry-systems, 24.3% by no-till cropping systems, 12.8% by planted commercial forest and forestation, 4.2% by biological N fixation and 2.0% by recycling the industrial organic wastes. The ecosystem carbon payback time for historical C losses from South America through LCA strategies may be 56 to 188years, and the adoption of LCA can also increase food and meat production by 615Mton or 17.6Mtonyear -1 and 56Mton or 1.6Mtonyear -1 , respectively, between 2016 and 2050. Copyright © 2016 Elsevier Ltd. All rights reserved.

Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bill Stanley; Patrick Gonzalez; Sandra Brown

2005-10-01

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects,more » providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st , 2005 and June 30th, 2005. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.« less

Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bill Stanley; Patrick Gonzalez; Sandra Brown

2006-01-01

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects,more » providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st , 2005 and June 30th, 2005. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.« less

Carbon Emission from Forest Fires on Scots Pine Logging Sites in the Angara Region of Central Siberia

NASA Astrophysics Data System (ADS)

Ivanova, G. A.; Conard, S. G.; McRae, D. J.; Kukavskaya, E. A.; Bogorodskaya, A. V.; Kovaleva, N. M.

2010-12-01

Wildfire and large-scale forest harvesting are the two major disturbances in the Russian boreal forests. Non-recovered logged sites total about a million hectares in Siberia. Logged sites are characterized by higher fire hazard than forest sites due to the presence of generally untreated logging slash (i.e., available fuel) which dries out much more rapidly compared to understory fuels. Moreover, most logging sites can be easily accessed by local population; this increases the risk for fire ignition. Fire impacts on the overstory trees, subcanopy woody layer, and ground vegetation biomass were estimated on 14 logged and unlogged comparison sites in the Lower Angara Region in 2009-2010 as part of the NASA-funded NEESPI project, The Influence of Changing Forestry Practices on the Effects of Wildfire and on Interactions Between Fire and Changing Climate in Central Siberia. Based on calculated fuel consumption, we estimated carbon emission from fires on both logged and unlogged burned sites. Carbon emission from fires on logged sites appeared to be twice that on unlogged sites. Soil respiration decreased on both site types after fires. This reduction may partially offset fire-produced carbon emissions. Carbon emissions from fire and post-fire ecosystem damage on logged sites are expected to increase under changing climate conditions and as a result of anticipated increases in future forest harvesting in Siberia.

Magnitude and Surface Rupture Length of Prehistoric Upper Crustal Earthquakes in the Puget Lowland, Washington State

NASA Astrophysics Data System (ADS)

Sherrod, B. L.; Styron, R. H.

2016-12-01

Paleoseismic studies documented prehistoric earthquakes after the last glaciation ended 15 ka on 13 upper-crustal fault zones in the Cascadia fore arc. These fault zones are a consequence of north-directed fore arc block migration manifesting as a series of bedrock uplifts and intervening structural basins in the southern Salish Sea lowland between Vancouver, B.C. to the north and Olympia, WA to the south, and bounded on the east and west by the Cascade Mountains and Olympic Mountains, respectively. Our dataset uses published information and includes 27 earthquakes tabulated from observations of postglacial deformation at 63 sites. Stratigraphic offsets along faults consist of two types of measurements: 1) vertical separation of strata along faults observed in fault scarp excavations, and 2) estimates from coastal uplift and subsidence. We used probabilistic methods to estimate past rupture magnitudes and surface rupture length (SRL), applying empirical observations from modern earthquakes and point measurements from paleoseismic sites (Biasi and Weldon, 2006). Estimates of paleoearthquake magnitude ranged between M 6.5 and M 7.5. SRL estimates varied between 20 and 90 km. Paleoearthquakes on the Seattle fault zone and Saddle Mountain West fault about 1100 years ago were outliers in our analysis. Large offsets observed for these two earthquakes implies a M 7.8 and 200 km SRL, given the average observed ratio of slip/SRL in modern earthquakes. The actual mapped traces of these faults are less than 200km, implying these earthquakes had an unusually high static stress drop or, in the case of the Seattle fault, splay faults may have accentuated uplift in the hanging wall. Refined calculations incorporating fault area may change these magnitude and SRL estimates. Biasi, G.P., and Weldon, R.J., 2006, Estimating Surface Rupture Length and Magnitude of Paleoearthquakes from Point Measurements of Rupture Displacement: B. Seismol. Soc. Am., 96, 1612-1623.

ac electroosmotic pumping induced by noncontact external electrodes

PubMed Central

Wang, Shau-Chun; Chen, Hsiao-Ping; Chang, Hsueh-Chia

2007-01-01

Electroosmotic (EO) pumps based on dc electroosmosis is plagued by bubble generation and other electrochemical reactions at the electrodes at voltages beyond 1 V for electrolytes. These disadvantages limit their throughput and offset their portability advantage over mechanical syringe or pneumatic pumps. ac electroosmotic pumps at high frequency (>100 kHz) circumvent the bubble problem by inducing polarization and slip velocity on embedded electrodes,1 but they require complex electrode designs to produce a net flow. We report a new high-throughput ac EO pump design based on induced-polarization on the entire channel surface instead of just on the electrodes. Like dc EO pumps, our pump electrodes are outside of the load section and form a cm-long pump unit consisting of three circular reservoirs (3 mm in diameter) connected by a 1×1 mm channel. The field-induced polarization can produce an effective Zeta potential exceeding 1 V and an ac slip velocity estimated as 1 mm∕sec or higher, both one order of magnitude higher than earlier dc and ac pumps, giving rise to a maximum throughput of 1 μl∕sec. Polarization over the entire channel surface, quadratic scaling with respect to the field and high voltage at high frequency without electrode bubble generation are the reasons why the current pump is superior to earlier dc and ac EO pumps. PMID:19693362

Image Quality Assessment Based on Local Linear Information and Distortion-Specific Compensation.

PubMed

Wang, Hanli; Fu, Jie; Lin, Weisi; Hu, Sudeng; Kuo, C-C Jay; Zuo, Lingxuan

2016-12-14

Image Quality Assessment (IQA) is a fundamental yet constantly developing task for computer vision and image processing. Most IQA evaluation mechanisms are based on the pertinence of subjective and objective estimation. Each image distortion type has its own property correlated with human perception. However, this intrinsic property may not be fully exploited by existing IQA methods. In this paper, we make two main contributions to the IQA field. First, a novel IQA method is developed based on a local linear model that examines the distortion between the reference and the distorted images for better alignment with human visual experience. Second, a distortion-specific compensation strategy is proposed to offset the negative effect on IQA modeling caused by different image distortion types. These score offsets are learned from several known distortion types. Furthermore, for an image with an unknown distortion type, a Convolutional Neural Network (CNN) based method is proposed to compute the score offset automatically. Finally, an integrated IQA metric is proposed by combining the aforementioned two ideas. Extensive experiments are performed to verify the proposed IQA metric, which demonstrate that the local linear model is useful in human perception modeling, especially for individual image distortion, and the overall IQA method outperforms several state-of-the-art IQA approaches.

Measurement of in vivo local shear modulus using MR elastography multiple-phase patchwork offsets.

PubMed

Suga, Mikio; Matsuda, Tetsuya; Minato, Kotaro; Oshiro, Osamu; Chihara, Kunihiro; Okamoto, Jun; Takizawa, Osamu; Komori, Masaru; Takahashi, Takashi

2003-07-01

Magnetic resonance elastography (MRE) is a method that can visualize the propagating and standing shear waves in an object being measured. The quantitative value of a shear modulus can be calculated by estimating the local shear wavelength. Low-frequency mechanical motion must be used for soft, tissue-like objects because a propagating shear wave rapidly attenuates at a higher frequency. Moreover, a propagating shear wave is distorted by reflections from the boundaries of objects. However, the distortions are minimal around the wave front of the propagating shear wave. Therefore, we can avoid the effect of reflection on a region of interest (ROI) by adjusting the duration of mechanical vibrations. Thus, the ROI is often shorter than the propagating shear wavelength. In the MRE sequence, a motion-sensitizing gradient (MSG) is synchronized with mechanical cyclic motion. MRE images with multiple initial phase offsets can be generated with increasing delays between the MSG and mechanical vibrations. This paper proposes a method for measuring the local shear wavelength using MRE multiple initial phase patchwork offsets that can be used when the size of the object being measured is shorter than the local wavelength. To confirm the reliability of the proposed method, computer simulations, a simulated tissue study and in vitro and in vivo studies were performed.

From sink to source: Regional variation in U.S. forest carbon futures

PubMed Central

Wear, David N.; Coulston, John W.

2015-01-01

The sequestration of atmospheric carbon (C) in forests has partially offset C emissions in the United States (US) and might reduce overall costs of achieving emission targets, especially while transportation and energy sectors are transitioning to lower-carbon technologies. Using detailed forest inventory data for the conterminous US, we estimate forests’ current net sequestration of atmospheric C to be 173 Tg yr−1, offsetting 9.7% of C emissions from transportation and energy sources. Accounting for multiple driving variables, we project a gradual decline in the forest C emission sink over the next 25 years (to 112 Tg yr−1) with regional differences. Sequestration in eastern regions declines gradually while sequestration in the Rocky Mountain region declines rapidly and could become a source of atmospheric C due to disturbances such as fire and insect epidemics. C sequestration in the Pacific Coast region stabilizes as forests harvested in previous decades regrow. Scenarios simulating climate-induced productivity enhancement and afforestation policies increase sequestration rates, but would not fully offset declines from aging and forest disturbances. Separating C transfers associated with land use changes from sequestration clarifies forests’ role in reducing net emissions and demonstrates that retention of forest land is crucial for protecting or enhancing sink strength. PMID:26558439

From sink to source: Regional variation in U.S. forest carbon futures.

PubMed

Wear, David N; Coulston, John W

2015-11-12

The sequestration of atmospheric carbon (C) in forests has partially offset C emissions in the United States (US) and might reduce overall costs of achieving emission targets, especially while transportation and energy sectors are transitioning to lower-carbon technologies. Using detailed forest inventory data for the conterminous US, we estimate forests' current net sequestration of atmospheric C to be 173 Tg yr(-1), offsetting 9.7% of C emissions from transportation and energy sources. Accounting for multiple driving variables, we project a gradual decline in the forest C emission sink over the next 25 years (to 112 Tg yr(-1)) with regional differences. Sequestration in eastern regions declines gradually while sequestration in the Rocky Mountain region declines rapidly and could become a source of atmospheric C due to disturbances such as fire and insect epidemics. C sequestration in the Pacific Coast region stabilizes as forests harvested in previous decades regrow. Scenarios simulating climate-induced productivity enhancement and afforestation policies increase sequestration rates, but would not fully offset declines from aging and forest disturbances. Separating C transfers associated with land use changes from sequestration clarifies forests' role in reducing net emissions and demonstrates that retention of forest land is crucial for protecting or enhancing sink strength.

Empirical Corrections to Nutation Amplitudes and Precession Computed from a Global VLBI Solution

NASA Astrophysics Data System (ADS)

Schuh, H.; Ferrandiz, J. M.; Belda-Palazón, S.; Heinkelmann, R.; Karbon, M.; Nilsson, T.

2017-12-01

The IAU2000A nutation and IAU2006 precession models were adopted to provide accurate estimations and predictions of the Celestial Intermediate Pole (CIP). However, they are not fully accurate and VLBI (Very Long Baseline Interferometry) observations show that the CIP deviates from the position resulting from the application of the IAU2006/2000A model. Currently, those deviations or offsets of the CIP (Celestial Pole Offsets - CPO), can only be obtained by the VLBI technique. The accuracy of the order of 0.1 milliseconds of arc (mas) allows to compare the observed nutation with theoretical prediction model for a rigid Earth and constrain geophysical parameters describing the Earth's interior. In this study, we empirically evaluate the consistency, systematics and deviations of the IAU 2006/2000A precession-nutation model using several CPO time series derived from the global analysis of VLBI sessions. The final objective is the reassessment of the precession offset and rate, and the amplitudes of the principal terms of nutation, trying to empirically improve the conventional values derived from the precession/nutation theories. The statistical analysis of the residuals after re-fitting the main nutation terms demonstrates that our empirical corrections attain an error reduction by almost 15 micro arc seconds.

The first geocenter estimation results using GPS measurements

NASA Technical Reports Server (NTRS)

Malla, R. P.; Wu, S. C.

1990-01-01

The center of mass of the Earth is the natural and unambiguous origin of a geocentric satellite dynamical system. A geocentric reference frame assumes that the origin of its coordinate axes is at the geocenter, in which all relevant observations and results can be referred and in which geodynamic theories or models for the dynamic behavior of Earth can be formulated. In practice, however, a kinematically obtained terrestrial reference frame may assume an origin other than the geocenter. A fast and accurate method of determining origin offset from the geocenter is highly desirable. Global Positioning System (GPS) measurements, because of their abundance and broad distribution, provide a powerful tool to obtain this origin offset in a short period of time. Two effective strategies have been devised. Data from the first Central and South America (Casa Uno) global GPS experiment were studied to demonstrate the ability of recovering the geocenter location with present-day GPS satellites and receivers.

Entirely relaxed lattice-mismatched GaSb/GaAs/Si(001) heterostructure grown via metalorganic chemical vapor deposition

NASA Astrophysics Data System (ADS)

Ha, Minh Thien Huu; Hoang Huynh, Sa; Binh Do, Huy; Nguyen, Tuan Anh; Luc, Quang Ho; Lee, Ching Ting; Chang, Edward Yi

2018-05-01

A GaSb epilayer is grown on a GaAs/Si(001) epitaxial substrate via metalorganic chemical vapor deposition. High-resolution transmission electron microscopy micrographs and high-resolution X-ray reciprocal space mapping indicate an entirely relaxed interfacial misfit (IMF) array GaSb epilayer. The valence-band offset and conduction-band offset of the Al2O3/GaSb/GaAs/Si structure are estimated to be 2.39 and 3.65 eV, respectively. The fabricated Al2O3/p-GaSb/GaAs/Si MOS capacitors exhibited good capacitance–voltage characteristics with a small accumulation frequency dispersion of approximately 1.05% per decade. These results imply that the GaSb epilayer grown on the GaAs/Si platform in the IMF mode can be used for future complementary metal–oxide semiconductor applications.

The causal effects of home care use on institutional long-term care utilization and expenditures.

PubMed

Guo, Jing; Konetzka, R Tamara; Manning, Willard G

2015-03-01

Limited evidence exists on whether expanding home care saves money overall or how much institutional long-term care can be reduced. This paper estimates the causal effect of Medicaid-financed home care services on the costs and utilization of institutional long-term care using Medicaid claims data. A unique instrumental variable was applied to address the potential bias caused by omitted variables or reverse effect of institutional care use. We find that the use of Medicaid-financed home care services significantly reduced but only partially offset utilization and Medicaid expenditures on nursing facility services. A $1000 increase in Medicaid home care expenditures avoided 2.75 days in nursing facilities and reduced annual Medicaid nursing facility costs by $351 among people over age 65 when selection bias is addressed. Failure to address selection biases would misestimate the substitution and offset effects. Copyright © 2015 John Wiley & Sons, Ltd.

The Relation Between Black Hole Mass and Velocity Dispersion at z ~ 0.37

DOE Office of Scientific and Technical Information (OSTI.GOV)

Treu, T.

2004-10-25

The velocity dispersion of 7 Seyfert 1 galaxies at z {approx} 0.37 is measured using high signal-to-noise Keck spectra. Black hole (BH) mass estimates are obtained via an empirically calibrated photoionization method. We derive the BH mass velocity dispersion relationship at z {approx} 0.37. We find an offset with respect to the local relationship, in the sense of somewhat lower velocity dispersion at a fixed BH mass at z {approx} 0.37 than today, significant at the 97% level. The offset corresponds to {Delta}log {sigma} = -0.16 with rms scatter of 0.13 dex. If confirmed by larger samples and independent checksmore » on systematic uncertainties and selection effects, this result would be consistent with spheroids evolving faster than BHs in the past 4 Gyrs and inconsistent with pure luminosity evolution.« less

Mobility of large rock avalanches: evidence from Valles Marineris, Mars

USGS Publications Warehouse

McEwen, A.S.

1989-01-01

Measurements of H/L (height of drop/length of runout) vs. volume for landslides in Valles Marineris on Mars show a trend of decreasing H/L with increasing volume. This trend, which is linear on a log-log plot, is parallel to but lies above the trend for terrestrial dry rock avalanches. This result and estimates of 104 to 105 Pa yield strength suggest that the landslides were not water saturated, as suggested by previous workers. The offset between the H/L vs. volume trends shows that a typical Martian avalanche must be nearly two orders of magnitude more voluminous than a typical terrestrial avalance in order to achieve the same mobility. This offset might be explained by the effects of gravity on flows with high yield strengths. These results should prove useful to future efforts to resolve the controversy over the mechanics of long-runout avalanches. -Author

Ground settlement monitoring from temporarily persistent scatterers between two SAR acquisitions

USGS Publications Warehouse

Lei, Z.; Xiaoli, D.; Guangcai, F.; Zhong, L.

2009-01-01

We present an improved differential interferometric synthetic aperture radar (DInSAR) analysis method that measures motions of scatterers whose phases are stable between two SAR acquisitions. Such scatterers are referred to as temporarily persistent scatterers (TPS) for simplicity. Unlike the persistent scatterer InSAR (PS-InSAR) method that relies on a time-series of interferograms, the new algorithm needs only one interferogram. TPS are identified based on pixel offsets between two SAR images, and are specially coregistered based on their estimated offsets instead of a global polynomial for the whole image. Phase unwrapping is carried out based on an algorithm for sparse data points. The method is successfully applied to measure the settlement in the Hong Kong Airport area. The buildings surrounded by vegetation were successfully selected as TPS and the tiny deformation signal over the area was detected. ??2009 IEEE.

Antiretroviral treatment-based cost saving interventions may offset expenses for new patients and earlier treatment start.

PubMed

Angeletti, C; Pezzotti, P; Antinori, A; Mammone, A; Navarra, A; Orchi, N; Lorenzini, P; Mecozzi, A; Ammassari, A; Murachelli, S; Ippolito, G; Girardi, E

2014-03-01

Combination antiretroviral therapy (cART) has become the main driver of total costs of caring for persons living with HIV (PLHIV). The present study estimated the short/medium-term cost trends in response to the recent evolution of national guidelines and regional therapeutic protocols for cART in Italy. We developed a deterministic mathematical model that was calibrated using epidemic data for Lazio, a region located in central Italy with about six million inhabitants. In the Base Case Scenario, the estimated number of PLHIV in the Lazio region increased over the period 2012-2016 from 14 414 to 17 179. Over the same period, the average projected annual cost for treating the HIV-infected population was €147.0 million. An earlier cART initiation resulted in a rise of 2.3% in the average estimated annual cost, whereas an increase from 27% to 50% in the proportion of naïve subjects starting cART with a nonnucleoside reverse transcriptase inhibitor (NNRTI)-based regimen resulted in a reduction of 0.3%. Simplification strategies based on NNRTIs co-formulated in a single tablet regimen and protease inhibitor/ritonavir-boosted monotherapy produced an overall reduction in average annual costs of 1.5%. A further average saving of 3.3% resulted from the introduction of generic antiretroviral drugs. In the medium term, cost saving interventions could finance the increase in costs resulting from the inertial growth in the number of patients requiring treatment and from the earlier treatment initiation recommended in recent guidelines. © 2013 British HIV Association.

Clinical Evaluation of 68Ga-PSMA-II and 68Ga-RM2 PET Images Reconstructed With an Improved Scatter Correction Algorithm.

PubMed

Wangerin, Kristen A; Baratto, Lucia; Khalighi, Mohammad Mehdi; Hope, Thomas A; Gulaka, Praveen K; Deller, Timothy W; Iagaru, Andrei H

2018-06-06

Gallium-68-labeled radiopharmaceuticals pose a challenge for scatter estimation because their targeted nature can produce high contrast in these regions of the kidneys and bladder. Even small errors in the scatter estimate can result in washout artifacts. Administration of diuretics can reduce these artifacts, but they may result in adverse events. Here, we investigated the ability of algorithmic modifications to mitigate washout artifacts and eliminate the need for diuretics or other interventions. The model-based scatter algorithm was modified to account for PET/MRI scanner geometry and challenges of non-FDG tracers. Fifty-three clinical 68 Ga-RM2 and 68 Ga-PSMA-11 whole-body images were reconstructed using the baseline scatter algorithm. For comparison, reconstruction was also processed with modified sampling in the single-scatter estimation and with an offset in the scatter tail-scaling process. None of the patients received furosemide to attempt to decrease the accumulation of radiopharmaceuticals in the bladder. The images were scored independently by three blinded reviewers using the 5-point Likert scale. The scatter algorithm improvements significantly decreased or completely eliminated the washout artifacts. When comparing the baseline and most improved algorithm, the image quality increased and image artifacts were reduced for both 68 Ga-RM2 and for 68 Ga-PSMA-11 in the kidneys and bladder regions. Image reconstruction with the improved scatter correction algorithm mitigated washout artifacts and recovered diagnostic image quality in 68 Ga PET, indicating that the use of diuretics may be avoided.

Disequilibrium δ18O values in microbial carbonates as a tracer of metabolic production of dissolved inorganic carbon

NASA Astrophysics Data System (ADS)

Thaler, Caroline; Millo, Christian; Ader, Magali; Chaduteau, Carine; Guyot, François; Ménez, Bénédicte

2017-02-01

Carbon and oxygen stable isotope compositions of carbonates are widely used to retrieve paleoenvironmental information. However, bias may exist in such reconstructions as carbonate precipitation is often associated with biological activity. Several skeleton-forming eukaryotes have been shown to precipitate carbonates with significant offsets from isotopic equilibrium with water. Although poorly understood, the origin of these biologically-induced isotopic shifts in biogenic carbonates, commonly referred to as "vital effects", could be related to metabolic effects that may not be restricted to mineralizing eukaryotes. The aim of our study was to determine whether microbially-mediated carbonate precipitation can also produce offsets from equilibrium for oxygen isotopes. We present here δ18O values of calcium carbonates formed by the activity of Sporosarcina pasteurii, a carbonatogenic bacterium whose ureolytic activity produces ammonia (thus increasing pH) and dissolved inorganic carbon (DIC) that precipitates as solid carbonates in the presence of Ca2+. We show that the 1000 lnαCaCO3-H2O values for these bacterially-precipitated carbonates are up to 24.7‰ smaller than those expected for precipitation at isotopic equilibrium. A similar experiment run in the presence of carbonic anhydrase (an enzyme able to accelerate oxygen isotope equilibration between DIC and water) resulted in δ18O values of microbial carbonates in line with values expected at isotopic equilibrium with water. These results demonstrate for the first time that bacteria can induce calcium carbonate precipitation in strong oxygen isotope disequilibrium with water, similarly to what is observed for eukaryotes. This disequilibrium effect can be unambiguously ascribed to oxygen isotope disequilibrium between DIC and water inherited from the oxygen isotope composition of the ureolytically produced CO2, probably combined with a kinetic isotope effect during CO2 hydration/hydroxylation. The fact that both disequilibrium effects are triggered by the metabolic production of CO2, which is common in many microbially-mediated carbonation processes, leads us to propose that metabolically-induced offsets from isotopic equilibrium in microbial carbonates may be more common than previously considered. Therefore, precaution should be taken when using the oxygen isotope signature of microbial carbonates for diagenetic and paleoenvironmental reconstructions.

Fault geometry and cumulative offsets in the central Coast Ranges, California: Evidence for northward increasing slip along the San Gregorio-San Simeon-Hosgri fault

USGS Publications Warehouse

Langenheim, V.E.; Jachens, R.C.; Graymer, R.W.; Colgan, J.P.; Wentworth, C.M.; Stanley, R.G.

2012-01-01

Estimates of the dip, depth extent, and amount of cumulative displacement along the major faults in the central California Coast Ranges are controversial. We use detailed aeromagnetic data to estimate these parameters for the San Gregorio–San Simeon–Hosgri and other faults. The recently acquired aeromagnetic data provide an areally consistent data set that crosses the onshore-offshore transition without disruption, which is particularly important for the mostly offshore San Gregorio–San Simeon–Hosgri fault. Our modeling, constrained by exposed geology and in some cases, drill-hole and seismic-reflection data, indicates that the San Gregorio–San Simeon–Hosgri and Reliz-Rinconada faults dip steeply throughout the seismogenic crust. Deviations from steep dips may result from local fault interactions, transfer of slip between faults, or overprinting by transpression since the late Miocene. Given that such faults are consistent with predominantly strike-slip displacement, we correlate geophysical anomalies offset by these faults to estimate cumulative displacements. We find a northward increase in right-lateral displacement along the San Gregorio–San Simeon–Hosgri fault that is mimicked by Quaternary slip rates. Although overall slip rates have decreased over the lifetime of the fault, the pattern of slip has not changed. Northward increase in right-lateral displacement is balanced in part by slip added by faults, such as the Reliz-Rinconada, Oceanic–West Huasna, and (speculatively) Santa Ynez River faults to the east.

Avoiding Stair-Step Artifacts in Image Registration for GOES-R Navigation and Registration Assessment

NASA Technical Reports Server (NTRS)

Grycewicz, Thomas J.; Tan, Bin; Isaacson, Peter J.; De Luccia, Frank J.; Dellomo, John

2016-01-01

In developing software for independent verification and validation (IVV) of the Image Navigation and Registration (INR) capability for the Geostationary Operational Environmental Satellite R Series (GOES-R) Advanced Baseline Imager (ABI), we have encountered an image registration artifact which limits the accuracy of image offset estimation at the subpixel scale using image correlation. Where the two images to be registered have the same pixel size, subpixel image registration preferentially selects registration values where the image pixel boundaries are close to lined up. Because of the shape of a curve plotting input displacement to estimated offset, we call this a stair-step artifact. When one image is at a higher resolution than the other, the stair-step artifact is minimized by correlating at the higher resolution. For validating ABI image navigation, GOES-R images are correlated with Landsat-based ground truth maps. To create the ground truth map, the Landsat image is first transformed to the perspective seen from the GOES-R satellite, and then is scaled to an appropriate pixel size. Minimizing processing time motivates choosing the map pixels to be the same size as the GOES-R pixels. At this pixel size image processing of the shift estimate is efficient, but the stair-step artifact is present. If the map pixel is very small, stair-step is not a problem, but image correlation is computation-intensive. This paper describes simulation-based selection of the scale for truth maps for registering GOES-R ABI images.

Addressing the [O III] / Hβ offset in metal poor star forming galaxies found in the RESOLVE survey and ECO catalog

NASA Astrophysics Data System (ADS)

Richardson, Chris T.; Kannappan, Sheila; Moffett, Amanda J.; RESOLVE survey team

2018-06-01

Metal poor star forming galaxies sit on the far left wing of the BPT diagram just below traditional demarcation lines. The basic approach to reproducing their emission lines by coupling photoionization models to stellar population synthesis models underestimates the observed [O III] / Hβ ratio by a factor 0.3-0.5 dex. We classified galaxies as metal poor in the REsolved Spectroscopy of a Local VolumE (RESOLVE) survey and the Environmental COntext (ECO) catalog by using the IZI code based off of Bayesian inference. We used a variety of stellar population synthesis codes to generate SEDs covering a range of starburst ages and metallicities including both secular and binary stellar evolution. Here, we show that multiple SPS codes can produce SEDs hard enough to reduce the offset assuming that simple, and perhaps unjustified, nebular conditions hold. Adopting more realistic nebular conditions shows that, despite the recent emphasis placed on binary evolution to fit high O III ratios, none of our SEDs can reduce the offset. We propose several new solutions including using ensembles of nebular clouds and improved microphysics to address this issue. This work is supported by National Science Foundation awards OCI-1053575, though XSEDE award TG-AST140040, and NSF awards AST-0955368 and CISE/ACI-1156614.

Green residues from Bangkok green space for renewable energy recovery, phosphorus recycling and greenhouse gases emission reduction.

PubMed

Thitanuwat, Bussarakam; Polprasert, Chongchin; Englande, Andrew J

2017-03-01

Effective ways to integrate human life quality, environmental pollution mitigation and efficient waste management strategies are becoming a crisis challenge for sustainable urban development. The aims of this study are: (1) to evaluate and recommend an optimum Urban Green Space (UGS) area for the Bangkok Metropolitan Administration (BMA); and (2) to quantify potential renewable resources including electricity generation and potential nutrient recovery from generated ash. Green House Gases (GHGs) emissions from the management of Green Residues (GR) produced in a recommended UGS expansion are estimated and compared with those from the existing BMA waste management practice. Results obtained from this study indicate that an increase in UGS from its current 2.02% to 22.4% of the BMA urban area is recommended. This optimum value is primarily due to the area needed as living space for its population. At this scale, GR produced of about 334kt·y -1 may be used to generate electricity at the rate of 206GWh·y -1 by employing incineration technology. Additionally, instead of going to landfill, phosphorus (P) contained in the ash of 1077 t P·y -1 could be recovered to produce P fertilizer to be recycled for agricultural cultivation. Income earned from selling these products is found to offset all of the operational cost of the proposed GR management methodology itself plus 7% of the cost of BMA's Municipal Solid Waste (MSW) operations. About 70% of the current GHGs emission may be reduced based on incineration simulation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Offsetting the impacts of mining to achieve no net loss of native vegetation.

PubMed

Sonter, L J; Barrett, D J; Soares-Filho, B S

2014-08-01

Offsets are a novel conservation tool, yet using them to achieve no net loss of biodiversity is challenging. This is especially true when using conservation offsets (i.e., protected areas) because achieving no net loss requires avoiding equivalent loss. Our objective was to determine if offsetting the impacts of mining achieves no net loss of native vegetation in Brazil's largest iron mining region. We used a land-use change model to simulate deforestation by mining to 2020; developed a model to allocate conservation offsets to the landscape under 3 scenarios (baseline, no new offsets; current practice, like-for-like [by vegetation type] conservation offsetting near the impact site; and threat scenario, like-for-like conservation offsetting of highly threatened vegetation); and simulated nonmining deforestation to 2020 for each scenario to quantify avoided deforestation achieved with offsets. Mines cleared 3570 ha of native vegetation by 2020. Under a 1:4 offset ratio, mining companies would be required to conserve >14,200 ha of native vegetation, doubling the current extent of protected areas in the region. Allocating offsets under current practice avoided deforestation equivalent to 3% of that caused by mining, whereas allocating under the threat scenario avoided 9%. Current practice failed to achieve no net loss because offsets did not conserve threatened vegetation. Explicit allocation of offsets to threatened vegetation also failed because the most threatened vegetation was widely dispersed across the landscape, making conservation logistically difficult. To achieve no net loss with conservation offsets requires information on regional deforestation trajectories and the distribution of threatened vegetation. However, in some regions achieving no net loss through conservation may be impossible. In these cases, other offsetting activities, such as revegetation, will be required. © 2014 Society for Conservation Biology.

VIRIAL BLACK HOLE MASS ESTIMATES FOR 280,000 AGNs FROM THE SDSS BROADBAND PHOTOMETRY AND SINGLE-EPOCH SPECTRA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kozłowski, Szymon, E-mail: simkoz@astrouw.edu.pl

2017-01-01

We use the Sloan Digital Sky Survey (SDSS) Quasar Data Release 12 (DR12Q), containing nearly 300,000 active galactic nuclei (AGNs), to calculate the monochromatic luminosities at 5100, 3000, and 1350 Å, derived from the broadband extinction-corrected SDSS magnitudes. After matching these sources to their counterparts from the SDSS Quasar Data Release 7 (DR7Q), we find very high correlations between our luminosities and DR7Q spectra-based luminosities with minute mean offsets (∼0.01 dex) and dispersions of differences of 0.11, 0.10, and 0.12 dex, respectively, across a luminosity range of 2.5 dex. We then estimate the black hole (BH) masses of the AGNsmore » using the broad line region radius–disk luminosity relations and the FWHM of the Mg ii and C iv emission lines, to provide a catalog of 283,033 virial BH mass estimates (132,451 for Mg ii, 213,071 for C iv, and 62,489 for both) along with the estimates of the bolometric luminosity and Eddington ratio for 0.1 <  z  < 5.5 and for roughly a quarter of the sky covered by SDSS. The BH mass estimates from Mg ii turned out to be closely matched to the ones from DR7Q with a dispersion of differences of 0.34 dex across a BH mass range of ∼2 dex. We uncovered a bias in the derived C iv FWHMs from DR12Q as compared to DR7Q, which we correct empirically. The C iv BH mass estimates should be used with caution because the C iv line is known to cause problems in the estimation of BH mass from single-epoch spectra. Finally, after the FWHM correction, the AGN BH mass estimates from C iv closely match the DR7Q ones (with a dispersion of 0.28 dex), and more importantly the Mg ii and C iv BH masses agree internally with a mean offset of 0.07 dex and a dispersion of 0.39 dex.« less

Cortical dynamics of figure-ground segmentation: shine-through.

PubMed

Francis, Gregory

2009-01-01

The shine-through effect occurs when a brief offset vernier target is followed by a grating of non-offset vernier elements. Rather than mask the target, this stimulus sequence produces a percept of the target vernier occluding the mask elements. We analyzed the dynamics of the 3D LAMINART model of depth perception and found that it explains the appearance of shine-through for these stimuli. The model explanation proposes that shine-through is due to a combination of false binocular disparity matches between the target and the central element of the mask, and a weakening of between disparity competition due to spatial competition and boundary grouping. Simulations of the model demonstrate that its behavior closely matches empirical data on the properties of shine-through. The model is contrasted with an alternative explanation of shine-through, and novel mask conditions are studied that allow for empirical tests of the model hypotheses.

A lumped mucosal wave model of the vocal folds revisited: recent extensions and oscillation hysteresis.

PubMed

Lucero, Jorge C; Koenig, Laura L; Lourenço, Kelem G; Ruty, Nicolas; Pelorson, Xavier

2011-03-01

This paper examines an updated version of a lumped mucosal wave model of the vocal fold oscillation during phonation. Threshold values of the subglottal pressure and the mean (DC) glottal airflow for the oscillation onset are determined. Depending on the nonlinear characteristics of the model, an oscillation hysteresis phenomenon may occur, with different values for the oscillation onset and offset threshold. The threshold values depend on the oscillation frequency, but the occurrence of the hysteresis is independent of it. The results are tested against pressure data collected from a mechanical replica of the vocal folds, and oral airflow data collected from speakers producing intervocalic /h/. In the human speech data, observed differences between voice onset and offset may be attributed to variations in voice pitch, with a very small or inexistent hysteresis phenomenon. © 2011 Acoustical Society of America

Microwave generation with low residual phase noise from a femtosecond fiber laser with an intracavity electro-optic modulator.

PubMed

Swann, William C; Baumann, Esther; Giorgetta, Fabrizio R; Newbury, Nathan R

2011-11-21

Low phase-noise microwave generation has previously been demonstrated using self-referenced frequency combs to divide down a low noise optical reference. We demonstrate an approach based on a fs Er-fiber laser that avoids the complexity of self-referenced stabilization of the offset frequency. Instead, the repetition rate of the femtosecond Er-fiber laser is phase locked to two cavity-stabilized cw fiber lasers that span 3.74 THz by use of an intracavity electro-optic modulator with over 2 MHz feedback bandwidth. The fs fiber laser effectively divides the 3.74 THz difference signal to produce microwave signals at harmonics of the repetition rate. Through comparison of two identical dividers, we measure a residual phase noise on a 1.5 GHz carrier of -120 dBc/Hz at 1 Hz offset. © 2011 Optical Society of America

Air Brayton Solar Receiver, phase 2

NASA Technical Reports Server (NTRS)

Deanda, L. E.

1981-01-01

An air Brayton solar receiver (ABSR) is discussed. The ABSR consists of a cylindrical, insulated, offset plate fin heat exchanger which is mounted at the focal plane of a fully tracking parabolic solar collector. The receiver transfer heat from the concentrated solar radiation (which impinges on the inside walls of the heat exchanger) to the working fluid i.e., air. The hot air would then e used to drive a small Brayton cycle heat engine. The engine in turn drives a generator which produces electrical energy. Symmetrical and asymmetrical solar power input into the ABSR are analyzed. The symmetrical cases involve the baseline incident flux and the axially shifted incident fluxes. The asymmetrical cases correspond to the solar fluxes that are obtained by reduced solar input from one half of the concentrator or by receiver offset of plus or minus 1 inch from the concentrator optical axis.

Polynomial-interpolation algorithm for van der Pauw Hall measurement in a metal hydride film

NASA Astrophysics Data System (ADS)

Koon, D. W.; Ares, J. R.; Leardini, F.; Fernández, J. F.; Ferrer, I. J.

2008-10-01

We apply a four-term polynomial-interpolation extension of the van der Pauw Hall measurement technique to a 330 nm Mg-Pd bilayer during both absorption and desorption of hydrogen at room temperature. We show that standard versions of the van der Pauw DC Hall measurement technique produce an error of over 100% due to a drifting offset signal and can lead to unphysical interpretations of the physical processes occurring in this film. The four-term technique effectively removes this source of error, even when the offset signal is drifting by an amount larger than the Hall signal in the time interval between successive measurements. This technique can be used to increase the resolution of transport studies of any material in which the resistivity is rapidly changing, particularly when the material is changing from metallic to insulating behavior.

Hayward Fault rate constraints at Berkeley: Evaluation of the 335-meter Strawberry Creek offset

NASA Astrophysics Data System (ADS)

Williams, P. L.

2007-12-01

At UC Berkeley the active channel of Strawberry Creek is offset 335 meters by the Hayward fault and two abandoned channels of Strawberry Creek are laterally offset 580 and 730 meters. These relationships record the displacement of the northern Hayward fault at Berkeley over a period of tens of millennia. The Strawberry Creek site has a similar geometry to the central San Andreas fault's Wallace Creek site, which arguably provides the best geological evidence of "millennial" fault kinematics in California (Sieh and Jahns, 1984). Slip rate determinations are an essential component of overall hazard evaluation for the Hayward fault, and this site is ripe to disclose a long-term form of this parameter, to contrast with geodetic and other geological rate evidence. Large offsets at the site may lower uncertainty in the rate equation relative to younger sites, as the affect of stream abandonment age, generally the greatest source of rate uncertainty, is greatly reduced. This is helpful here because it more-than-offsets uncertainties resulting from piercing projections to the fault. Strawberry Creek and its ancestral channels suggest west-side-up vertical deformation across the Hayward fault at this location. The development of the vertical deformation parameter will complement ongoing geodetic measurements, particularly InSAR, and motivate testing of other geological constraints. Up-to-the-west motion across the Hayward fault at Berkeley has important implications for the partitioning of strain and kinematics of the northern Hayward fault, and may explain anomalous up-on-the-west landforms elsewhere along the fault. For example, geological features of the western Berkeley Hills are consistent with rapid and recent uplift to the west of the fault. On the basis of a preliminary analysis of the offset channels of Strawberry Creek, up-to-the-west uplift is about 0.5mm/yr across the Hayward fault at Berkeley. If this is in fact the long-term rate, the 150 m height of the Hills to the northwest of the Strawberry Creek site was produced during the past about 300,000 years by a significant dip- slip (thrust) component of Hayward fault motion. Rapid and recent uplift of some portions of the East Bay Hills has important implications for fault geometries and slope stability, and should strongly influence the investigation fault hazards in areas that are more complexly deformed.

Interior micro-CT with an offset detector

PubMed Central

Sharma, Kriti Sen; Gong, Hao; Ghasemalizadeh, Omid; Yu, Hengyong; Wang, Ge; Cao, Guohua

2014-01-01

Purpose: The size of field-of-view (FOV) of a microcomputed tomography (CT) system can be increased by offsetting the detector. The increased FOV is beneficial in many applications. All prior investigations, however, have been focused to the case in which the increased FOV after offset-detector acquisition can cover the transaxial extent of an object fully. Here, the authors studied a new problem where the FOV of a micro-CT system, although increased after offset-detector acquisition, still covers an interior region-of-interest (ROI) within the object. Methods: An interior-ROI-oriented micro-CT scan with an offset detector poses a difficult reconstruction problem, which is caused by both detector offset and projection truncation. Using the projection completion techniques, the authors first extended three previous reconstruction methods from offset-detector micro-CT to offset-detector interior micro-CT. The authors then proposed a novel method which combines two of the extended methods using a frequency split technique. The authors tested the four methods with phantom simulations at 9.4%, 18.8%, 28.2%, and 37.6% detector offset. The authors also applied these methods to physical phantom datasets acquired at the same amounts of detector offset from a customized micro-CT system. Results: When the detector offset was small, all reconstruction methods showed good image quality. At large detector offset, the three extended methods gave either visible shading artifacts or high deviation of pixel value, while the authors’ proposed method demonstrated no visible artifacts and minimal deviation of pixel value in both the numerical simulations and physical experiments. Conclusions: For an interior micro-CT with an offset detector, the three extended reconstruction methods can perform well at a small detector offset but show strong artifacts at a large detector offset. When the detector offset is large, the authors’ proposed reconstruction method can outperform the three extended reconstruction methods by suppressing artifacts and maintaining pixel values. PMID:24877826

Finding the buried memory of past earthquakes with geophysical, GPR-based paleoseismology

NASA Astrophysics Data System (ADS)

Manighetti, I.; Beaupretre, S.; Garambois, S.; Malavieille, J.; Chatton, M.; Sénéchal, G.

2011-12-01

We hypothesized that, in places where sedimentation and erosion compete at fast rates, part of the memory of past earthquakes on faults may be buried, hence hidden, in the first tens meters of the ground. We test that hypothesis on a fast slipping, large, strike-slip fault (Hope, New Zealand), at a site where marked alluvial conditions prevail (Terako). We first use LiDAR data to analyze the ground surface morphology of the 2 km2 site at the greatest resolution. About twenty clear, distinct, morphological markers are observed -mainly alluvial terrace risers and small stream channels, all are laterally offset by the fault. The measured offsets range between 3 and 200 m, yet are discrete and showing several large slip gaps. The measurements are well-constrained and allow estimating the mean slip per event amplitude to 3.9 ± 1.4 m, and the last earthquake slip to 3 ± 0.5 m. About 10 past earthquakes are well documented in the surface data, while about 50 are requested to account for the 200 m largest cumulative slip. We then investigate the zone (on smaller area, 400 x 600 m2) with dense, pseudo-3D Ground Penetrating Radar (GPR) data. We measured 56, ~400 m-long, 5-10 m spaced GPR profiles (250 MHz), parallel to the fault and evenly distributed on either sides. Their analysis reveals the existence of several tens morphological markers buried in the first 3 m of the ground, most of them do not imprint the ground surface as they are blanketed with a 0.1-3 m-thick poorly reflective layer. A few buried markers exhibit however surface expressions. All buried markers are laterally offset by the fault. Based on a number of evidence, we interpret these buried markers as stream channels, most were decapitated by the repeated fault slips and abandoned. We measured ~50 lateral offsets in the buried channel network, almost three times more than at the surface. These offsets range between 2.5 and 106 m, as observed at the surface, yet provide a more continuous record of the fault slip. The similarity of the successive slip increments suggests a slip per event averaging 3.9 ± 1.9 m, similar to that estimated from surface data. From the total 'surface and buried' offset collection, we infer that a minimum of 30 large earthquakes have broken the Hope fault at the Terako site in the last 5 kyrs, with an average slip per event of 3.8 ± 1.3 m, an average recurrence time of 100-250 yrs, and a likely magnitude of at least Mw 7.2-7.7. The last major earthquake likely occurred at 1875 ± 15 AD, in agreement with previous suggestions. Our study therefore confirms that part of the memory of past earthquakes may indeed reside in the first tens meters of the ground, where it may be explored with a novel type, geophysical and GPR-based, paleoseismology. We emphasize that developing such a new paleoseismology will provide a rich information complementary to surface observation, and help documenting the past earthquakes on faults.

Slip rate and slip magnitudes of past earthquakes along the Bogd left-lateral strike-slip fault (Mongolia)

USGS Publications Warehouse

Rizza, M.; Ritz, J.-F.; Braucher, R.; Vassallo, R.; Prentice, C.; Mahan, S.; McGill, S.; Chauvet, A.; Marco, S.; Todbileg, M.; Demberel, S.; Bourles, D.

2011-01-01

We carried out morphotectonic studies along the left-lateral strike-slip Bogd Fault, the principal structure involved in the Gobi-Altay earthquake of 1957 December 4 (published magnitudes range from 7.8 to 8.3). The Bogd Fault is 260 km long and can be subdivided into five main geometric segments, based on variation in strike direction. West to East these segments are, respectively: the West Ih Bogd (WIB), The North Ih Bogd (NIB), the West Ih Bogd (WIB), the West Baga Bogd (WBB) and the East Baga Bogd (EBB) segments. Morphological analysis of offset streams, ridges and alluvial fans-particularly well preserved in the arid environment of the Gobi region-allows evaluation of late Quaternary slip rates along the different faults segments. In this paper, we measure slip rates over the past 200 ka at four sites distributed across the three western segments of the Bogd Fault. Our results show that the left-lateral slip rate is ~1 mm yr-1 along the WIB and EIB segments and ~0.5 mm yr-1 along the NIB segment. These variations are consistent with the restraining bend geometry of the Bogd Fault. Our study also provides additional estimates of the horizontal offset associated with the 1957 earthquake along the western part of the Bogd rupture, complementing previously published studies. We show that the mean horizontal offset associated with the 1957 earthquake decreases progressively from 5.2 m in the west to 2.0 m in the east, reflecting the progressive change of kinematic style from pure left-lateral strike-slip faulting to left-lateral-reverse faulting. Along the three western segments, we measure cumulative displacements that are multiples of the 1957 coseismic offset, which may be consistent with a characteristic slip. Moreover, using these data, we re-estimate the moment magnitude of the Gobi-Altay earthquake at Mw 7.78-7.95. Combining our slip rate estimates and the slip distribution per event we also determined a mean recurrence interval of ~2500-5200 yr for past earthquakes along the different segments of the western Bogd Fault. This suggests that the three western segments of the Bogd Fault and the Gurvan Bulag thrust fault (a reverse fault bounding the southern side of the Ih Bogd range that ruptured during the 1957 earthquake) have similar average recurrence times, and therefore may have ruptured together in previous earthquakes as they did in 1957. These results suggest that the western part of the Bogd Fault system, including the Gurvan Bulag thrust fault, usually behaves in a 'characteristic earthquake' mode. ?? 2011 The Authors Geophysical Journal International ?? 2011 RAS.

Slip rate and slip magnitudes of past earthquakes along the Bogd left-lateral strike-slip fault (Mongolia)

USGS Publications Warehouse

Prentice, Carol S.; Rizza, M.; Ritz, J.F.; Baucher, R.; Vassallo, R.; Mahan, S.

2011-01-01

We carried out morphotectonic studies along the left-lateral strike-slip Bogd Fault, the principal structure involved in the Gobi-Altay earthquake of 1957 December 4 (published magnitudes range from 7.8 to 8.3). The Bogd Fault is 260 km long and can be subdivided into five main geometric segments, based on variation in strike direction. West to East these segments are, respectively: the West Ih Bogd (WIB), The North Ih Bogd (NIB), the West Ih Bogd (WIB), the West Baga Bogd (WBB) and the East Baga Bogd (EBB) segments. Morphological analysis of offset streams, ridges and alluvial fans—particularly well preserved in the arid environment of the Gobi region—allows evaluation of late Quaternary slip rates along the different faults segments. In this paper, we measure slip rates over the past 200 ka at four sites distributed across the three western segments of the Bogd Fault. Our results show that the left-lateral slip rate is∼1 mm yr–1 along the WIB and EIB segments and∼0.5 mm yr–1 along the NIB segment. These variations are consistent with the restraining bend geometry of the Bogd Fault. Our study also provides additional estimates of the horizontal offset associated with the 1957 earthquake along the western part of the Bogd rupture, complementing previously published studies. We show that the mean horizontal offset associated with the 1957 earthquake decreases progressively from 5.2 m in the west to 2.0 m in the east, reflecting the progressive change of kinematic style from pure left-lateral strike-slip faulting to left-lateral-reverse faulting. Along the three western segments, we measure cumulative displacements that are multiples of the 1957 coseismic offset, which may be consistent with a characteristic slip. Moreover, using these data, we re-estimate the moment magnitude of the Gobi-Altay earthquake at Mw 7.78–7.95. Combining our slip rate estimates and the slip distribution per event we also determined a mean recurrence interval of∼2500–5200 yr for past earthquakes along the different segments of the western Bogd Fault. This suggests that the three western segments of the Bogd Fault and the Gurvan Bulag thrust fault (a reverse fault bounding the southern side of the Ih Bogd range that ruptured during the 1957 earthquake) have similar average recurrence times, and therefore may have ruptured together in previous earthquakes as they did in 1957. These results suggest that the western part of the Bogd Fault system, including the Gurvan Bulag thrust fault, usually behaves in a ‘characteristic earthquake’ mode.

Influence of camera parameters on the quality of mobile 3D capture

NASA Astrophysics Data System (ADS)

Georgiev, Mihail; Boev, Atanas; Gotchev, Atanas; Hannuksela, Miska

2010-01-01

We investigate the effect of camera de-calibration on the quality of depth estimation. Dense depth map is a format particularly suitable for mobile 3D capture (scalable and screen independent). However, in real-world scenario cameras might move (vibrations, temp. bend) form their designated positions. For experiments, we create a test framework, described in the paper. We investigate how mechanical changes will affect different (4) stereo-matching algorithms. We also assess how different geometric corrections (none, motion compensation-like, full rectification) will affect the estimation quality (how much offset can be still compensated with "crop" over a larger CCD). Finally, we show how estimated camera pose change (E) relates with stereo-matching, which can be used for "rectification quality" measure.

5 CFR 837.701 - Offset from supplemental annuity.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Offset from supplemental annuity. 837.701... REGULATIONS (CONTINUED) REEMPLOYMENT OF ANNUITANTS CSRS Offset § 837.701 Offset from supplemental annuity. (a) OPM will reduce the supplemental annuity of an individual who has performed CSRS-Offset service, if...

7 CFR 3.46 - Offset against tax refunds.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 1 2010-01-01 2010-01-01 false Offset against tax refunds. 3.46 Section 3.46 Agriculture Office of the Secretary of Agriculture DEBT MANAGEMENT Administrative Offset § 3.46 Offset against tax refunds. USDA will take action to effect administrative offset against tax refunds due to debtors...

40 CFR 93.163 - Timing of offsets and mitigation measures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Timing of offsets and mitigation... offsets and mitigation measures. (a) The emissions reductions from an offset or mitigation measure used to... offset or mitigation measure with emissions reductions in another year will not: (i) Cause or contribute...

40 CFR 93.163 - Timing of offsets and mitigation measures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Timing of offsets and mitigation... offsets and mitigation measures. (a) The emissions reductions from an offset or mitigation measure used to... offset or mitigation measure with emissions reductions in another year will not: (i) Cause or contribute...

40 CFR 93.163 - Timing of offsets and mitigation measures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Timing of offsets and mitigation... offsets and mitigation measures. (a) The emissions reductions from an offset or mitigation measure used to... offset or mitigation measure with emissions reductions in another year will not: (i) Cause or contribute...