Addressing FinFET metrology challenges in 1X node using tilt-beam CD-SEM

NASA Astrophysics Data System (ADS)

Zhang, Xiaoxiao; Zhou, Hua; Ge, Zhenhua; Vaid, Alok; Konduparthi, Deepasree; Osorio, Carmen; Ventola, Stefano; Meir, Roi; Shoval, Ori; Kris, Roman; Adan, Ofer; Bar-Zvi, Maayan

2014-04-01

At 1X node, 3D FinFETS raise a number of new metrology challenges. Gate height and fin height are two of the most important parameters for process control. At present there is a metrology gap in inline in-die measurement of these parameters. In order to fill this metrology gap, in-column beam tilt has been developed and implemented on Applied Materials V4i+ top-down CD-SEM for height measurement. A low tilt (5°) beam and a high tilt (14°) beam have been calibrated to obtain two sets of images providing measurement of sidewall edge width to calculate height in the host. Evaluations are done with applications in both gate height and fin height. TEM correlation with R2 being 0.89 and precision of 0.81nm have been achieved on various in-die features in gate height application. Fin height measurement shows less accuracy (R2 being 0.77) and precision (1.49 nm) due to challenges brought by fin geometry, yet still promising as first attempt. Sensitivity to DOE offset, die-to-die and in-die variation is demonstrated in both gate height and fin height. Process defect is successfully captured from inline wafers with gate height measurement implemented in production. This is the first successful demonstration of inline in-die gate height measurement for 14nm FinFET process control.

Rolled-out collectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shurcliff, W.A.

1979-04-01

SolaRoll is a solar collector material composed of extruded strips of black ethylene propylene diene monomer (EPDM) that is suitable for water or air type collectors. SolaRoll is provided in rolls and consists of an absorber mat with tubes and fins and a framing strip comprising all the parts of the collector frame. The rolls are bent in a counterflow pattern to cover the entire collector area and the mat is fastened with a thermosetting mastic adhesive. The heat transfer fluid is plain water as freezing does not injure the EPDM. Installation of the glazing in the framing strip ismore » described. EPDM has the disadvantage of low thermal conductivity but its use does not require antifreeze or a heat exchanger. Design options and suitable applications of SolaRoll systems are discussed.« less

Pegasus XL CYGNSS Fin Installation

NASA Image and Video Library

2016-09-21

Technicians prepare to install one of the fins on the Orbital ATK Pegasus XL rocket inside Building 1555 at Vandenberg Air Force Base in California. The fins will provide aerodynamic stability during flight. The rocket is being prepared at Vandenberg, and then will be transported to NASA’s Kennedy Space Center in Florida, attached to the Orbital ATK L-1011 carrier aircraft with NASA’s Cyclone Global Navigation Satellite System (CYGNSS) in its payload fairing. CYGNSS will launch on the Pegasus XL rocket from the Skid Strip at Cape Canaveral Air Force Station. CYGNSS will make frequent and accurate measurements of ocean surface winds throughout the life cycle of tropical storms and hurricanes. The data that CYGNSS provides will enable scientists to probe key air-sea interaction processes that take place near the core of storms, which are rapidly changing and play a critical role in the beginning and intensification of hurricanes.

Pegasus XL CYGNSS Fin Installation

NASA Image and Video Library

2016-09-21

Technicians prepare one of the fins for installation on the Orbital ATK Pegasus XL rocket inside Building 1555 at Vandenberg Air Force Base in California. The fins will provide aerodynamic stability during flight. The rocket is being prepared at Vandenberg, and then will be transported to NASA’s Kennedy Space Center in Florida, attached to the Orbital ATK L-1011 carrier aircraft with NASA’s Cyclone Global Navigation Satellite System (CYGNSS) in its payload fairing. CYGNSS will launch on the Pegasus XL rocket from the Skid Strip at Cape Canaveral Air Force Station. CYGNSS will make frequent and accurate measurements of ocean surface winds throughout the life cycle of tropical storms and hurricanes. The data that CYGNSS provides will enable scientists to probe key air-sea interaction processes that take place near the core of storms, which are rapidly changing and play a critical role in the beginning and intensification of hurricanes.

Pegasus XL CYGNSS Fin Installation

NASA Image and Video Library

2016-09-21

Technicians prepare to install one of the fins on the Orbital ATK Pegasus XL rocket inside Building 1555 at Vandenberg Air Force Base in California. The fins will provide aerodynamic stability during flight. The rocket is being prepared at Vandenberg, and then will be transported to NASA’s Kennedy Space Center in Florida attached to the Orbital ATK L-1011 carrier aircraft with NASA’s Cyclone Global Navigation Satellite System (CYGNSS) in its payload fairing. CYGNSS will launch on the Pegasus XL rocket from the Skid Strip at Cape Canaveral Air Force Station. CYGNSS will make frequent and accurate measurements of ocean surface winds throughout the life cycle of tropical storms and hurricanes. The data that CYGNSS provides will enable scientists to probe key air-sea interaction processes that take place near the core of storms, which are rapidly changing and play a critical role in the beginning and intensification of hurricanes.

Brayton-cycle heat exchanger technology program

NASA Technical Reports Server (NTRS)

Killackey, J. J.; Coombs, M. G.; Graves, R. F.; Morse, C. J.

1976-01-01

The following five tasks designed to advance this development of heat exchanger systems for close loop Brayton cycle power systems are presented: (1) heat transfer and pressure drop data for a finned tubular heat transfer matrix. The tubes are arranged in a triangular array with copper stainless steel laminate strips helically wound on the tubes to form a disk fin geometry; (2) the development of a modularized waste heat exchanger. Means to provide verified double containment are described; (3) the design, fabrication, and test of compact plate fin heat exchangers representative of full scale Brayton cycle recuperators; (4) the analysis and design of bellows suitable for operation at 1600 F and 200 psia for 1,000 cycles and 50,000 hours creep life; and (5) screening tests used to select a low cost braze alloy with the desirable attributes of a gold base alloy. A total of 22 different alloys were investigated; the final selection was Nicrobraz 30.

Parametric study of graphite foam fins and application in heat exchangers

NASA Astrophysics Data System (ADS)

Collins, Michael

This thesis focuses on the simulation and experimental studies of finned graphite foam extended surfaces to test their heat transfer characteristics and potential applications in condensers. Different fin designs were developed to conduct a parametric study on the thermal effectiveness with respect to thickness, spacing and fin offset angle. Each fin design was computationally simulated to estimate the heat transfer under specific conditions. The simulations showed that this optimal fin configuration could conduct more than 297% the amount of thermal energy as compared to straight aluminum fins. Graphite foam fins were then implemented into a simulation of the condenser system. The condenser was simulated with six different orientations of baffles to examine the incoming vapor and resulting two-phase flow patterns. The simulations showed that using both horizontal and vertical baffling provided the configuration with the highest heat transfer and minimized the bypass regions where the vapor would circumvent the graphite foam. This baffle configuration increased the amount of vapor flow through the inner graphite fins and cold water pipes, which gave this configuration the highest heat transfer. The results from experimental tests using the condenser system confirmed that using three baffles will increase performance consistent with the simulation results. The experimental data showed that the condenser using graphite foam had five times the heat transfer compared to the condenser using only aluminum fins. Incorporating baffles into the condenser using graphite foam enabled this system to conduct nearly ten times more heat transfer than the condenser system which only had aluminum fins without baffles. The results from this research indicate that graphite foam is a far superior material heat transfer enhancement material for heat transfer compared to aluminum used as an extended surface. The longitudinal and horizontal baffles incorporated into the condenser system greatly enhanced the heat transfer because of the increased interaction with the porous graphite foam fins.

The Magellanic Inter-Cloud Project (MAGIC) III: first spectroscopic evidence of a dwarf stripping a dwarf

NASA Astrophysics Data System (ADS)

Carrera, Ricardo; Conn, Blair C.; Noël, Noelia E. D.; Read, Justin I.; López Sánchez, Ángel R.

2017-11-01

The Magellanic Bridge (MB) is a gaseous stream that links the Large (LMC) and Small (SMC) Magellanic Clouds. Current simulations suggest that the MB forms from a recent interaction between the Clouds. In this scenario, the MB should also have an associated stellar bridge formed by stars tidally stripped from the SMC by the LMC. There are several observational evidences for these stripped stars, from the presence of intermediate age populations in the MB and carbon stars, to the recent observation of an over-density of RR Lyrae stars offset from the MB. However, spectroscopic confirmation of stripped stars in the MB remains lacking. In this paper, we use medium resolution spectra to derive the radial velocities and metallicities of stars in two fields along the MB. We show from both their chemistry and kinematics that the bulk of these stars must have been tidally stripped from the SMC. This is the first spectroscopic evidence for a dwarf galaxy being tidally stripped by a larger dwarf.

Preliminary Evaluation of the Radiometric Calibration of LANDSAT-4 Thematic Mapper Data by the Canada Centre for Remote Sensing

NASA Technical Reports Server (NTRS)

Murphy, J.; Park, W.; Fitzgerald, A.

1985-01-01

The radiometric characteristics of the LANDSAT-4 TM sensor are being studied with a view to developing absolute and relative radiometric calibration procedures. Preliminary results from several different approaches to the relative correction of all detectors within each band are reported. Topics covered include: the radiometric correction method; absolute calibration; the relative radiometric calibration algorithm; relative gain and offset calibration; relative gain and offset observations; and residual radiometric stripping.

Propulsion of a fin whale (Balaenoptera physalus): why the fin whale is a fast swimmer.

PubMed

Bose, N; Lien, J

1989-07-22

Measurements of an immature fin whale (Balaenoptera physalus), which died as a result of entrapment in fishing gear near Frenchmans Cove, Newfoundland (47 degrees 9' N, 55 degrees 25' W), were made to obtain estimates of volume and surface area of the animal. Detailed measurements of the flukes, both planform and sections, were also obtained. A strip theory was developed to calculate the hydrodynamic performance of the whale's flukes as an oscillating propeller. This method is based on linear, two-dimensional, small-amplitude, unsteady hydrofoil theory with correction factors used to account for the effects of finite span and finite amplitude motion. These correction factors were developed from theoretical results of large-amplitude heaving motion and unsteady lifting-surface theory. A model that makes an estimate of the effects of viscous flow on propeller performance was superimposed on the potential-flow results. This model estimates the drag of the hydrofoil sections by assuming that the drag is similar to that of a hydrofoil section in steady flow. The performance characteristics of the flukes of the fin whale were estimated by using this method. The effects of the different correction factors, and of the frictional drag of the fluke sections, are emphasized. Frictional effects in particular were found to reduce the hydrodynamic efficiency of the flukes significantly. The results are discussed and compared with the known characteristics of fin-whale swimming.

Great hammerhead sharks swim on their side to reduce transport costs

PubMed Central

Payne, Nicholas L.; Iosilevskii, Gil; Barnett, Adam; Fischer, Chris; Graham, Rachel T.; Gleiss, Adrian C.; Watanabe, Yuuki Y.

2016-01-01

Animals exhibit various physiological and behavioural strategies for minimizing travel costs. Fins of aquatic animals play key roles in efficient travel and, for sharks, the functions of dorsal and pectoral fins are considered well divided: the former assists propulsion and generates lateral hydrodynamic forces during turns and the latter generates vertical forces that offset sharks' negative buoyancy. Here we show that great hammerhead sharks drastically reconfigure the function of these structures, using an exaggerated dorsal fin to generate lift by swimming rolled on their side. Tagged wild sharks spend up to 90% of time swimming at roll angles between 50° and 75°, and hydrodynamic modelling shows that doing so reduces drag—and in turn, the cost of transport—by around 10% compared with traditional upright swimming. Employment of such a strongly selected feature for such a unique purpose raises interesting questions about evolutionary pathways to hydrodynamic adaptations, and our perception of form and function. PMID:27457414

An IPMC-enabled bio-inspired bending/twisting fin for underwater applications

NASA Astrophysics Data System (ADS)

Palmre, Viljar; Hubbard, Joel J.; Fleming, Maxwell; Pugal, David; Kim, Sungjun; Kim, Kwang J.; Leang, Kam K.

2013-01-01

This paper discusses the design, fabrication, and characterization of an ionic polymer-metal composite (IPMC) actuator-based bio-inspired active fin capable of bending and twisting motion. It is pointed out that IPMC strip actuators are used in the simple cantilever configuration to create simple bending (flapping-like) motion for propulsion in underwater autonomous systems. However, the resulting motion is a simple 1D bending and performance is rather limited. To enable more complex deformation, such as the flapping (pitch and heaving) motion of real pectoral and caudal fish fins, a new approach which involves molding or integrating IPMC actuators into a soft boot material to create an active control surface (called a ‘fin’) is presented. The fin can be used to realize complex deformation depending on the orientation and placement of the actuators. In contrast to previously created IPMCs with patterned electrodes for the same purpose, the proposed design avoids (1) the more expensive process of electroless plating platinum all throughout the surface of the actuator and (2) the need for specially patterning the electrodes. Therefore, standard shaped IPMC actuators such as those with rectangular dimensions with varying thicknesses can be used. One unique advantage of the proposed structural design is that custom shaped fins and control surfaces can be easily created without special materials processing. The molding process is cost effective and does not require functionalizing or ‘activating’ the boot material similar to creating IPMCs. For a prototype fin (90 mm wide × 60 mm long × 1.5 mm thick), the measured maximum tip displacement was approximately 44 mm and the twist angle of the fin exceeded 10°. Lift and drag measurements in water where the prototype fin with an airfoil profile was dragged through water at a velocity of 21 cm s-1 showed that the lift and drag forces can be affected by controlling the IPMCs embedded into the fin structure. These results suggest that such IPMC-enabled fin designs can be used for developing active propeller blades or control surfaces on underwater vehicles.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ranjan, Devesh

Diffusion bonded heat exchangers are the leading candidates for the sCO 2 Brayton cycles in next generation nuclear power plants. Commercially available diffusion bonded heat exchangers utilize set of continuous semi-circular zigzag micro channels to increase the heat transfer area and enhance heat transfer through increased turbulence production. Such heat exchangers can lead to excessive pressure drop as well as flow maldistribution in the case of poorly designed flow distribution headers. The goal of the current project is to fabricate and test potential discontinuous fin patterns for diffusion bonded heat exchangers; which can achieve desired thermal performance at lower pressuremore » drops. Prototypic discontinuous offset rectangular and Airfoil fin surface geometries were chemically etched on to 316 stainless steel plate and sealed against an un-etched flat pate using O-ring seal emulating diffusion bonded heat exchangers. Thermal-hydraulic performance of these prototypic discontinuous fin geometries was experimentally evaluated and compared to the existing data for the continuous zigzag channels. The data generated from this project will serve as the database for future testing and validation of numerical models.« less

Integrated current collector and catalyst support

DOEpatents

Bregoli, Lawrence J.

1985-10-22

An integrated current collecting electrode for a molten carbonate fuel cell includes a corrugated metal conductive strip positioned in contact with a catalyst layer. The corrugations of the metal strip form a plurality of gas channels immediately adjacent the surface of the catalyst through which a reactant gas flows. Each channel is filled with a particulate material to maintain separation between the metal strip and the catalyst in ensuring gas channel integrity. The catalyst may be in the form of a compacted, particulate material provided the particle size of the material within the gas channels is larger than that of the catalyst particles to prevent catalyst migration to the metal conductor and provide reactant gas access to the catalyst layer. The gas channels formed by the corrugations of the metal strip are arranged in an offset pattern along the direction of gas flow for improved reactant gas distribution to the catalyst layer. The particulate material positioned within the gas flow channels may be a ceramic conductor such as a perovskite or a spinel for enhanced current collection.

Integrated current collector and catalyst support

DOEpatents

Bregoli, L.J.

1984-10-17

An integrated current collecting electrode for a molten carbonate fuel cell includes a corrugated metal conductive strip positioned in contact with a catalyst layer. The corrugations of the metal strip form a plurality of gas channels immediately adjacent the surface of the catalyst through which a reactant gas flows. Each channel is filled with a particulate material to maintain separation between the metal strip and the catalyst in ensuring gas channel integrity. The catalyst may be in the form of a compacted, particulate material provided the particle size of the material within the gas channels is larger than that of the catalyst particles to prevent catalyst migration to the metal conductor and provide reactant gas access to the catalyst layer. The gas channels formed by the corrugations of the metal strip are arranged in an offset pattern along the direction of gas flow for improved reactant gas distribution to the catalyst layer. The particulate material positioned within the gas flow channels may be a ceramic conductor such as a perovskite or a spinel for enhanced current collection.

Numerical comparison of convective heat transfer augmentation devices used in cooling channels of hypersonic vehicles

NASA Astrophysics Data System (ADS)

Maldonado, Jaime J.

1994-04-01

Hypersonic vehicles are exposed to extreme thermal conditions compared to subsonic aircraft; therefore, some level of thermal management is required to protect the materials used. Normally, hypersonic vehicles experience the highest temperatures in the nozzle throat, and aircraft and propulsion system leading edges. Convective heat transfer augmentation techniques can be used in the thermal management system to increase heat transfer of the cooling channels in those areas. The techniques studied in this report are pin-fin, offset-fin, ribbed and straight roughened channel. A smooth straight channel is used as the baseline for comparing the techniques. SINDA '85, a lumped parameter finite difference thermal analyzer, is used to model the channels. Subroutines are added to model the fluid flow assuming steady one dimensional compressible flow with heat addition and friction. Correlations for convective heat transfer and friction are used in conjunction with the fluid flow analysis mentioned. As expected, the pin-fin arrangement has the highest heat transfer coefficient and the largest pressure drop. All the other devices fall in between the pin-fin and smooth straight channel. The selection of the best heat augmentation method depends on the design requirements. A good approach may be a channel using a combination of the techniques. For instance, several rows of pin-fins may be located at the region of highest heat flux, surrounded by some of the other techniques. Thus, the heat transfer coefficient is maximized at the region of highest heat flux while the pressure drop is not excessive.

Numerical comparison of convective heat transfer augmentation devices used in cooling channels of hypersonic vehicles

NASA Technical Reports Server (NTRS)

Maldonado, Jaime J.

1994-01-01

Hypersonic vehicles are exposed to extreme thermal conditions compared to subsonic aircraft; therefore, some level of thermal management is required to protect the materials used. Normally, hypersonic vehicles experience the highest temperatures in the nozzle throat, and aircraft and propulsion system leading edges. Convective heat transfer augmentation techniques can be used in the thermal management system to increase heat transfer of the cooling channels in those areas. The techniques studied in this report are pin-fin, offset-fin, ribbed and straight roughened channel. A smooth straight channel is used as the baseline for comparing the techniques. SINDA '85, a lumped parameter finite difference thermal analyzer, is used to model the channels. Subroutines are added to model the fluid flow assuming steady one dimensional compressible flow with heat addition and friction. Correlations for convective heat transfer and friction are used in conjunction with the fluid flow analysis mentioned. As expected, the pin-fin arrangement has the highest heat transfer coefficient and the largest pressure drop. All the other devices fall in between the pin-fin and smooth straight channel. The selection of the best heat augmentation method depends on the design requirements. A good approach may be a channel using a combination of the techniques. For instance, several rows of pin-fins may be located at the region of highest heat flux, surrounded by some of the other techniques. Thus, the heat transfer coefficient is maximized at the region of highest heat flux while the pressure drop is not excessive.

Erosion rills offset the efficacy of vegetated buffer strips to mitigate pesticide exposure in surface waters.

PubMed

Stehle, Sebastian; Dabrowski, James Michael; Bangert, Uli; Schulz, Ralf

2016-03-01

Regulatory risk assessment considers vegetated buffer strips as effective risk mitigation measures for the reduction of runoff-related pesticide exposure of surface waters. However, apart from buffer strip widths, further characteristics such as vegetation density or the presence of erosion rills are generally neglected in the determination of buffer strip mitigation efficacies. This study conducted a field survey of fruit orchards (average slope 3.1-12.2%) of the Lourens River catchment, South Africa, which specifically focused on the characteristics and attributes of buffer strips separating orchard areas from tributary streams. In addition, in-stream and erosion rill water samples were collected during three runoff events and GIS-based modeling was employed to predict losses of pesticides associated with runoff. The results show that erosion rills are common in buffer strips (on average 13 to 24 m wide) of the tributaries (up to 6.5 erosion rills per km flow length) and that erosion rills represent concentrated entry pathways of pesticide runoff into the tributaries during rainfall events. Exposure modeling shows that measured pesticide surface water concentrations correlated significantly (R(2)=0.626; p<0.001) with runoff losses predicted by the modeling approach in which buffer strip width was set to zero at sites with erosion rills; in contrast, no relationship between predicted runoff losses and in-stream pesticide concentrations were detected in the modeling approach that neglected erosion rills and thus assumed efficient buffer strips. Overall, the results of our study show that erosion rills may substantially reduce buffer strip pesticide retention efficacies during runoff events and suggest that the capability of buffer strips as a risk mitigation tool for runoff is largely overestimated in current regulatory risk assessment procedures conducted for pesticide authorization. Copyright © 2015 Elsevier B.V. All rights reserved.

Limitations on near-surface correction for multicomponent offset VSP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Macbeth, C.; Li, X.Y.; Horne, S.

1994-12-31

Multicomponent data are degraded due to near-surface scattering and non-ideal or unexpected source behavior. These effects cannot be neglected when interpreting relative wavefield attributes derived from compressional and shear waves. They confuse analyses based on standard scalar procedures and a prima facia interpretation of the vector wavefield properties. Here, the authors highlight two unique polar matrix decompositions for near-surface correction in offset VSPs, consider their inherent mathematical constraints and how they impact on subsurface interpretation. The first method is applied to a four component subset of a six component field data from a configuration of three concentric rings and walkawaymore » source positions forming offset VSPs in the Cymric field, California. The correction appears successful in automatically converting the wavefield into its ideal form, and the qSl polarizations scatter around N15{degree}E in agreement with the layer stripping of Winterstein and Meadows (1991).« less

Proceedings of the 35th Annual Symposium on Frequency Control, 27-29 May 1981, Philadelphia, Pennsylvania.

DTIC Science & Technology

1981-01-01

elements are fabricated using thin The OSLO produces a signal offset of +80KHz from film techniques in seven discrete values including ! the synthesizer input...contributing blood to the slurry from his/her fin- produced an estimated 100,000 crystal units during ger tips. Many strange and wonderful devices...disappeared or have changed names and 1o- electronic instruments and machine tools, and cations so many times that to trace their records supplies in an

Baseline requirements can hinder trades in water quality trading programs: Evidence from the Conestoga watershed.

PubMed

Ghosh, Gaurav; Ribaudo, Marc; Shortle, James

2011-08-01

The U.S. Environmental Protection Agency (USEPA) and the U.S. Department of Agriculture (USDA) are promoting point/nonpoint trading as a way of reducing the costs of meeting water quality goals. Farms can create offsets by implementing management practices such as conservation tillage, nutrient management and buffer strips. To be eligible to sell offsets or credits, farmers must first comply with baseline requirements. USEPA guidance recommends that the baseline for nonpoint sources be management practices that are consistent with the water quality goal. A farmer would not be able to create offsets until the minimum practice standards are met. An alternative baseline is those practices being implemented at the time the trading program starts, or when the farmer enters the program. The selection of the baseline affects the efficiency and equity of the trading program. It has major implications for which farmers benefit from trading, the cost of nonpoint source offsets, and ultimately the number of offsets that nonpoint sources can sell to regulated point sources. We use a simple model of the average profit-maximizing dairy farmer operating in the Conestoga watershed in Pennsylvania to evaluate the implications of baseline requirements on the cost and quantity of offsets that can be produced for sale in a water quality trading market, and which farmers benefit most from trading. Published by Elsevier Ltd.

Air Brayton Solar Receiver, phase 2

NASA Technical Reports Server (NTRS)

Deanda, L. E.

1981-01-01

An air Brayton solar receiver (ABSR) is discussed. The ABSR consists of a cylindrical, insulated, offset plate fin heat exchanger which is mounted at the focal plane of a fully tracking parabolic solar collector. The receiver transfer heat from the concentrated solar radiation (which impinges on the inside walls of the heat exchanger) to the working fluid i.e., air. The hot air would then e used to drive a small Brayton cycle heat engine. The engine in turn drives a generator which produces electrical energy. Symmetrical and asymmetrical solar power input into the ABSR are analyzed. The symmetrical cases involve the baseline incident flux and the axially shifted incident fluxes. The asymmetrical cases correspond to the solar fluxes that are obtained by reduced solar input from one half of the concentrator or by receiver offset of plus or minus 1 inch from the concentrator optical axis.

ANSYS Fluent Modelling of an Underexpanded Supersonic Sootblower Jet Impinging into Recovery Boiler Tube Geometries

NASA Astrophysics Data System (ADS)

Doroudi, Shahed

Sootblowers generate high pressure supersonic steam jets to control fireside deposition on heat transfer tubes of a kraft recovery boiler. Sootblowing is energy expensive, using 3-12% of the mill's total steam production. This motivates research on the dynamics of sootblower jet interaction with tubes and deposits, to optimize their use. A CFD investigation was performed using ANSYS Fluent 15.0 to model three-dimensional steady-state impingement of a Mach 2.5 mildly underexpanded (PR 1.2) air jet onto arrays of cylindrical tubes with and without fins, at various nozzle-to-tube centerline offsets. A free jet and four impingement cases for each of the economizer and generating bank geometries are compared to experimental visualizations. Pressure distributions on impinging surfaces suggest that the fins in the economizer produce a reduced but uniform sootblowing force. Pressure contours along the tubes (in the vertical direction) show a sharp decline one tube diameter away from the jet mid-plane.

Nonlinear Equations of Motion for Cantilever Rotor Blades in Hover with Pitch Link Flexibility, Twist, Precone, Droop, Sweep, Torque Offset, and Blade Root Offset

NASA Technical Reports Server (NTRS)

Hodges, D. H.

1976-01-01

Nonlinear equations of motion for a cantilever rotor blade are derived for the hovering flight condition. The blade is assumed to have twist, precone, droop, sweep, torque offset and blade root offset, and the elastic axis and the axes of center of mass, tension, and aerodynamic center coincident at the quarter chord. The blade is cantilevered in bending, but has a torsional root spring to simulate pitch link flexibility. Aerodynamic forces acting on the blade are derived from strip theory based on quasi-steady two-dimensional airfoil theory. The equations are hybrid, consisting of one integro-differential equation for root torsion and three integro-partial differential equations for flatwise and chordwise bending and elastic torsion. The equations are specialized for a uniform blade and reduced to nonlinear ordinary differential equations by Galerkin's method. They are linearized for small perturbation motions about the equilibrium operating condition. Modal analysis leads to formulation of a standard eigenvalue problem where the elements of the stability matrix depend on the solution of the equilibrium equations. Two different forms of the root torsion equation are derived that yield virtually identical numerical results. This provides a reasonable check for the accuracy of the equations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, H; Cho, H; Molloi, S

Purpose: To investigate the feasibility of energy response calibration of a Si strip photon-counting detector by using the x-ray fluorescence technique. Methods: X-ray fluorescence was generated by using a pencil beam from a tungsten anode x-ray tube with 2 mm Al filtration. Spectra were acquired at 90° from the primary beam direction with an energy-resolved photon-counting detector based on Si strips. The distances from the source to target and the target to detector were approximately 19 and 11 cm, respectively. Four different materials, containing Ag, I, Ba, and Gd, were placed in small plastic aliquots with a diameter of approximatelymore » 0.7 cm for x-ray fluorescence measurements. Linear regression analysis was performed to derive the gain and offset values for the correlation between the measured fluorescence peak center and the known energies for materials. The energy resolution was derived from the full width at half maximum (FWHM) of the fluorescence peaks. In addition, the angular dependence of the recorded fluorescence spectra was studied at 30°, 60°, and 120°. Results: Strong fluorescence signals of all four target materials were recorded with the investigated geometry for the Si strip detector. The recorded pulse height was calibrated with respect to photon energy and the gain and offset values were calculated to be 7.0 mV/keV and −69.3 mV, respectively. Negligible variation in energy calibration was observed among the four energy thresholds. The variation among different pixels was estimated to be approximately 1 keV. The energy resolution of the detector was estimated to be 7.9% within the investigated energy range. Conclusion: The performance of a spectral imaging system using energy-resolved photon-counting detectors is very dependent on the energy calibration of the detector. The proposed x-ray fluorescence technique provides an accurate and efficient way to calibrate the energy response of a photon-counting detector.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, Huanjun; Cho, Hyo-Min; Molloi, Sabee, E-mail: symolloi@uci.edu

Purpose: To investigate the feasibility of characterizing a Si strip photon-counting detector using x-ray fluorescence. Methods: X-ray fluorescence was generated by using a pencil beam from a tungsten anode x-ray tube with 2 mm Al filtration. Spectra were acquired at 90° from the primary beam direction with an energy-resolved photon-counting detector based on an edge illuminated Si strip detector. The distances from the source to target and the target to detector were approximately 19 and 11 cm, respectively. Four different materials, containing silver (Ag), iodine (I), barium (Ba), and gadolinium (Gd), were placed in small plastic containers with a diametermore » of approximately 0.7 cm for x-ray fluorescence measurements. Linear regression analysis was performed to derive the gain and offset values for the correlation between the measured fluorescence peak center and the known fluorescence energies. The energy resolutions and charge-sharing fractions were also obtained from analytical fittings of the recorded fluorescence spectra. An analytical model, which employed four parameters that can be determined from the fluorescence calibration, was used to estimate the detector response function. Results: Strong fluorescence signals of all four target materials were recorded with the investigated geometry for the Si strip detector. The average gain and offset of all pixels for detector energy calibration were determined to be 6.95 mV/keV and −66.33 mV, respectively. The detector’s energy resolution remained at approximately 2.7 keV for low energies, and increased slightly at 45 keV. The average charge-sharing fraction was estimated to be 36% within the investigated energy range of 20–45 keV. The simulated detector output based on the proposed response function agreed well with the experimental measurement. Conclusions: The performance of a spectral imaging system using energy-resolved photon-counting detectors is very dependent on the energy calibration of the detector. The proposed x-ray fluorescence technique offers an accurate and efficient way to calibrate the energy response of a photon-counting detector.« less

Heterogeneous Integration of Epitaxial Ge on Si using AlAs/GaAs Buffer Architecture: Suitability for Low-power Fin Field-Effect Transistors

PubMed Central

Hudait, Mantu K.; Clavel, Michael; Goley, Patrick; Jain, Nikhil; Zhu, Yan

2014-01-01

Germanium-based materials and device architectures have recently appeared as exciting material systems for future low-power nanoscale transistors and photonic devices. Heterogeneous integration of germanium (Ge)-based materials on silicon (Si) using large bandgap buffer architectures could enable the monolithic integration of electronics and photonics. In this paper, we report on the heterogeneous integration of device-quality epitaxial Ge on Si using composite AlAs/GaAs large bandgap buffer, grown by molecular beam epitaxy that is suitable for fabricating low-power fin field-effect transistors required for continuing transistor miniaturization. The superior structural quality of the integrated Ge on Si using AlAs/GaAs was demonstrated using high-resolution x-ray diffraction analysis. High-resolution transmission electron microscopy confirmed relaxed Ge with high crystalline quality and a sharp Ge/AlAs heterointerface. X-ray photoelectron spectroscopy demonstrated a large valence band offset at the Ge/AlAs interface, as compared to Ge/GaAs heterostructure, which is a prerequisite for superior carrier confinement. The temperature-dependent electrical transport properties of the n-type Ge layer demonstrated a Hall mobility of 370 cm2/Vs at 290 K and 457 cm2/Vs at 90 K, which suggests epitaxial Ge grown on Si using an AlAs/GaAs buffer architecture would be a promising candidate for next-generation high-performance and energy-efficient fin field-effect transistor applications. PMID:25376723

Two-Phase Flow in Microchannels with Non-Circular Cross Section

NASA Astrophysics Data System (ADS)

Eckett, Chris A.; Strumpf, Hal J.

2002-11-01

Two-phase flow in microchannels is of practical importance in several microgravity space technology applications. These include evaporative and condensing heat exchangers for thermal management systems and vapor cycle systems, phase separators, and bioreactors. The flow passages in these devices typically have a rectangular cross-section or some other non-circular cross-section; may include complex flow paths with branches, merges and bends; and may involve channel walls of different wettability. However, previous experimental and analytical investigations of two-phase flow in reduced gravity have focussed on straight, circular tubes. This study is an effort to determine two-phase flow behavior, both with and without heat transfer, in microchannel configurations other than straight, circular tubes. The goals are to investigate the geometrical effects on flow pattern, pressure drop and liquid holdup, as well as to determine the relative importance of capillary, surface tension, inertial, and gravitational forces in such geometries. An evaporative heat exchanger for microgravity thermal management systems has been selected as the target technology in this investigation. Although such a heat exchanger has never been developed at Honeywell, a preliminary sizing has been performed based on knowledge of such devices in normal gravity environments. Fin shapes considered include plain rectangular, offset rectangular, and wavy fin configurations. Each of these fin passages represents a microchannel of non-circular cross section. The pans at the inlet and outlet of the heat exchanger are flow branches and merges, with up to 90-deg bends. R-134a has been used as the refrigerant fluid, although ammonia may well be used in the eventual application.

NASA Tech Briefs, May 2010

NASA Technical Reports Server (NTRS)

2010-01-01

Topics covered include: Instrument for Analysis of Greenland's Glacier Mills Cryogenic Moisture Apparatus; A Transportable Gravity Gradiometer Based on Atom Interferometry; Three Methods of Detection of Hydrazines; Crossed, Small-Deflection Energy Analyzer for Wind/Temperature Spectrometer; Wavefront Correction for Large, Flexible Antenna Reflector; Novel Micro Strip-to-Waveguide Feed Employing a Double-Y Junction; Thin-Film Ferro Electric-Coupled Microstripline Phase Shifters With Reduced Device Hysteresis; Two-Stage, 90-GHz, Low-Noise Amplifier; A 311-GHz Fundamental Oscillator Using InP HBT Technology; FPGA Coprocessor Design for an Onboard Multi-Angle Spectro-Polarimetric Imager; Serrating Nozzle Surfaces for Complete Transfer of Droplets; Turbomolecular Pumps for Holding Gases in Open Containers; Triaxial Swirl Injector Element for Liquid-Fueled Engines; Integrated Budget Office Toolbox; PLOT3D Export Tool for Tecplot; Math Description Engine Software Development Kit; Astronaut Office Scheduling System Software; ISS Solar Array Management; Probabilistic Structural Analysis Program; SPOT Program; Integrated Hybrid System Architecture for Risk Analysis; System for Packaging Planetary Samples for Return to Earth; Offset Compound Gear Drive; Low-Dead-Volume Inlet for Vacuum Chamber; Simple Check Valves for Microfluidic Devices; A Capillary-Based Static Phase Separator for Highly Variable Wetting Conditions; Gimballing Spacecraft Thruster; Finned Carbon-Carbon Heat Pipe with Potassium Working Fluid; Lightweight Heat Pipes Made from Magnesium; Ceramic Rail-Race Ball Bearings; Improved OTEC System for a Submarine Robot; Reflector Surface Error Compensation in Dual-Reflector Antennas; Enriched Storable Oxidizers for Rocket Engines; Planar Submillimeter-Wave Mixer Technology with Integrated Antenna; Widely Tunable Mode-Hop-Free External-Cavity Quantum Cascade Laser; Non-Geiger-Mode Single-Photon Avalanche Detector with Low Excess Noise; Using Whispering-Gallery-Mode Resonators for Refractometry; RF Device for Acquiring Images of the Human Body; Reactive Collision Avoidance Algorithm; Fast Solution in Sparse LDA for Binary Classification; Modeling Common-Sense Decisions in Artificial Intelligence; Graph-Based Path-Planning for Titan Balloons; Nanolaminate Membranes as Cylindrical Telescope Reflectors; Air-Sea Spray Airborne Radar Profiler Characterizes Energy Fluxes in Hurricanes; Large Telescope Segmented Primary Mirror Alignment; and Simplified Night Sky Display System.

Analytic description of the frictionally engaged in-plane bending process incremental swivel bending (ISB)

NASA Astrophysics Data System (ADS)

Frohn, Peter; Engel, Bernd; Groth, Sebastian

2018-05-01

Kinematic forming processes shape geometries by the process parameters to achieve a more universal process utilizations regarding geometric configurations. The kinematic forming process Incremental Swivel Bending (ISB) bends sheet metal strips or profiles in plane. The sequence for bending an arc increment is composed of the steps clamping, bending, force release and feed. The bending moment is frictionally engaged by two clamping units in a laterally adjustable bending pivot. A minimum clamping force hindering the material from slipping through the clamping units is a crucial criterion to achieve a well-defined incremental arc. Therefore, an analytic description of a singular bent increment is developed in this paper. The bending moment is calculated by the uniaxial stress distribution over the profiles' width depending on the bending pivot's position. By a Coulomb' based friction model, necessary clamping force is described in dependence of friction, offset, dimensions of the clamping tools and strip thickness as well as material parameters. Boundaries for the uniaxial stress calculation are given in dependence of friction, tools' dimensions and strip thickness. The results indicate that changing the bending pivot to an eccentric position significantly affects the process' bending moment and, hence, clamping force, which is given in dependence of yield stress and hardening exponent. FE simulations validate the model with satisfactory accordance.

Characterization of energy response for photon-counting detectors using x-ray fluorescence

PubMed Central

Ding, Huanjun; Cho, Hyo-Min; Barber, William C.; Iwanczyk, Jan S.; Molloi, Sabee

2014-01-01

Purpose: To investigate the feasibility of characterizing a Si strip photon-counting detector using x-ray fluorescence. Methods: X-ray fluorescence was generated by using a pencil beam from a tungsten anode x-ray tube with 2 mm Al filtration. Spectra were acquired at 90° from the primary beam direction with an energy-resolved photon-counting detector based on an edge illuminated Si strip detector. The distances from the source to target and the target to detector were approximately 19 and 11 cm, respectively. Four different materials, containing silver (Ag), iodine (I), barium (Ba), and gadolinium (Gd), were placed in small plastic containers with a diameter of approximately 0.7 cm for x-ray fluorescence measurements. Linear regression analysis was performed to derive the gain and offset values for the correlation between the measured fluorescence peak center and the known fluorescence energies. The energy resolutions and charge-sharing fractions were also obtained from analytical fittings of the recorded fluorescence spectra. An analytical model, which employed four parameters that can be determined from the fluorescence calibration, was used to estimate the detector response function. Results: Strong fluorescence signals of all four target materials were recorded with the investigated geometry for the Si strip detector. The average gain and offset of all pixels for detector energy calibration were determined to be 6.95 mV/keV and −66.33 mV, respectively. The detector’s energy resolution remained at approximately 2.7 keV for low energies, and increased slightly at 45 keV. The average charge-sharing fraction was estimated to be 36% within the investigated energy range of 20–45 keV. The simulated detector output based on the proposed response function agreed well with the experimental measurement. Conclusions: The performance of a spectral imaging system using energy-resolved photon-counting detectors is very dependent on the energy calibration of the detector. The proposed x-ray fluorescence technique offers an accurate and efficient way to calibrate the energy response of a photon-counting detector. PMID:25471962

The Evaporation and Survival of Cluster Galaxy Coronae. I. The Effectiveness of Isotropic Thermal Conduction Including Saturation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vijayaraghavan, Rukmani; Sarazin, Craig, E-mail: rukmani@virginia.edu

We simulate the evolution of cluster galaxy hot interstellar medium (ISM) gas that is a result of the effects of ram pressure and thermal conduction in the intracluster medium (ICM). At the density and temperature of the ICM, the mean free paths of ICM electrons are comparable to the sizes of galaxies, therefore electrons can efficiently transport heat that is due to thermal conduction from the hot ICM to the cooler ISM. Galaxies consisting of dark matter halos and hot gas coronae are embedded in an ICM-like “wind tunnel” in our simulations. In this paper, we assume that thermal conductionmore » is isotropic and include the effects of saturation. We find that as heat is transferred from the ICM to the ISM, the cooler denser ISM expands and evaporates. This process is significantly faster than gas loss due to ram pressure stripping; for our standard model galaxy, the evaporation time is 160 Myr, while the ram pressure stripping timescale is 2.5 Gyr. Thermal conduction also suppresses the formation of shear instabilities, and there are no stripped ISM tails since the ISM evaporates before tails can form. Observations of long-lived X-ray emitting coronae and ram pressure stripped X-ray tails in galaxies in group and cluster environments therefore require that thermal conduction is suppressed or offset by some additional physical process. The most likely process is anisotropic thermal conduction that is due to magnetic fields in the ISM and ICM, which we simulate and study in the next paper in this series.« less

The Evaporation and Survival of Cluster Galaxy Coronae. I. The Effectiveness of Isotropic Thermal Conduction Including Saturation

NASA Astrophysics Data System (ADS)

Vijayaraghavan, Rukmani; Sarazin, Craig

2017-05-01

We simulate the evolution of cluster galaxy hot interstellar medium (ISM) gas that is a result of the effects of ram pressure and thermal conduction in the intracluster medium (ICM). At the density and temperature of the ICM, the mean free paths of ICM electrons are comparable to the sizes of galaxies, therefore electrons can efficiently transport heat that is due to thermal conduction from the hot ICM to the cooler ISM. Galaxies consisting of dark matter halos and hot gas coronae are embedded in an ICM-like “wind tunnel” in our simulations. In this paper, we assume that thermal conduction is isotropic and include the effects of saturation. We find that as heat is transferred from the ICM to the ISM, the cooler denser ISM expands and evaporates. This process is significantly faster than gas loss due to ram pressure stripping; for our standard model galaxy, the evaporation time is 160 Myr, while the ram pressure stripping timescale is 2.5 Gyr. Thermal conduction also suppresses the formation of shear instabilities, and there are no stripped ISM tails since the ISM evaporates before tails can form. Observations of long-lived X-ray emitting coronae and ram pressure stripped X-ray tails in galaxies in group and cluster environments therefore require that thermal conduction is suppressed or offset by some additional physical process. The most likely process is anisotropic thermal conduction that is due to magnetic fields in the ISM and ICM, which we simulate and study in the next paper in this series.

Effect of Ion Flux (Dose Rate) in Source-Drain Extension Ion Implantation for 10-nm Node FinFET and Beyond on 300/450mm Platforms

NASA Astrophysics Data System (ADS)

Shen, Ming-Yi

The improvement of wafer equipment productivity has been a continuous effort of the semiconductor industry. Higher productivity implies lower product price, which economically drives more demand from the market. This is desired by the semiconductor manufacturing industry. By raising the ion beam current of the ion implanter for 300/450mm platforms, it is possible to increase the throughput of the ion implanter. The resulting dose rate can be comparable to the performance of conventional ion implanters or higher, depending on beam current and beam size. Thus, effects caused by higher dose rate must be investigated further. One of the major applications of ion implantation (I/I) is source-drain extension (SDE) I/I for the silicon FinFET device. This study investigated the dose rate effects on the material properties and device performance of the 10-nm node silicon FinFET. In order to gain better understanding of the dose rate effects, the dose rate study is based on Synopsys Technology CAD (TCAD) process and device simulations that are calibrated and validated using available structural silicon fin samples. We have successfully shown that the kinetic monte carlo (KMC) I/I simulation can precisely model both the silicon amorphization and the arsenic distribution in the fin by comparing the KMC simulation results with TEM images. The results of the KMC I/I simulation show that at high dose rate more activated arsenic dopants were in the source-drain extension (SDE) region. This finding matches with the increased silicon amorphization caused by the high dose-rate I/I, given that the arsenic atoms could be more easily activated by the solid phase epitaxial regrowth process. This increased silicon amorphization led to not only higher arsenic activation near the spacer edge, but also less arsenic atoms straggling into the channel. Hence, it is possible to improve the throughput of the ion implanter when the dopants are implanted at high dose rate if the same doping level with a lower wafer dose can be achieved. In addition, the leakage current might also be reduced due to less undesired dopants in the channel. However, the twin defects from the problematic Si{111} recrystallization is well-known to cause excessive leakage current to the FinFET. This drawback can offset the benefits of the high dose rate I/I mentioned above. This work produced the first attempt at simulating the electrical impact of twin defects on advanced-node (10 nm) FinFET device performance. It was found that the high dose-rate I/I causes more twin defects in the silicon fin, and the physical locations of these defects were close to the channel. The defects undesirably induced trap-assisted band-to-band tunneling near the drain, which increased the leakage current. This issue could be mitigated by using asymmetrical gate overlap/underlap design or thicker spacer for SDE I/I so that the twin defects are not located in the depletion region near the drain.

Photon caliper to achieve submillimeter positioning accuracy

NASA Astrophysics Data System (ADS)

Gallagher, Kyle J.; Wong, Jennifer; Zhang, Junan

2017-09-01

The purpose of this study was to demonstrate the feasibility of using a commercial two-dimensional (2D) detector array with an inherent detector spacing of 5 mm to achieve submillimeter accuracy in localizing the radiation isocenter. This was accomplished by delivering the Vernier ‘dose’ caliper to a 2D detector array where the nominal scale was the 2D detector array and the non-nominal Vernier scale was the radiation dose strips produced by the high-definition (HD) multileaf collimators (MLCs) of the linear accelerator. Because the HD MLC sequence was similar to the picket fence test, we called this procedure the Vernier picket fence (VPF) test. We confirmed the accuracy of the VPF test by offsetting the HD MLC bank by known increments and comparing the known offset with the VPF test result. The VPF test was able to determine the known offset within 0.02 mm. We also cross-validated the accuracy of the VPF test in an evaluation of couch hysteresis. This was done by using both the VPF test and the ExacTrac optical tracking system to evaluate the couch position. We showed that the VPF test was in agreement with the ExacTrac optical tracking system within a root-mean-square value of 0.07 mm for both the lateral and longitudinal directions. In conclusion, we demonstrated the VPF test can determine the offset between a 2D detector array and the radiation isocenter with submillimeter accuracy. Until now, no method to locate the radiation isocenter using a 2D detector array has been able to achieve such accuracy.

Energy Calibration of a Silicon-Strip Detector for Photon-Counting Spectral CT by Direct Usage of the X-ray Tube Spectrum

NASA Astrophysics Data System (ADS)

Liu, Xuejin; Chen, Han; Bornefalk, Hans; Danielsson, Mats; Karlsson, Staffan; Persson, Mats; Xu, Cheng; Huber, Ben

2015-02-01

The variation among energy thresholds in a multibin detector for photon-counting spectral CT can lead to ring artefacts in the reconstructed images. Calibration of the energy thresholds can be used to achieve homogeneous threshold settings or to develop compensation methods to reduce the artefacts. We have developed an energy-calibration method for the different comparator thresholds employed in a photon-counting silicon-strip detector. In our case, this corresponds to specifying the linear relation between the threshold positions in units of mV and the actual deposited photon energies in units of keV. This relation is determined by gain and offset values that differ for different detector channels due to variations in the manufacturing process. Typically, the calibration is accomplished by correlating the peak positions of obtained pulse-height spectra to known photon energies, e.g. with the aid of mono-energetic x rays from synchrotron radiation, radioactive isotopes or fluorescence materials. Instead of mono-energetic x rays, the calibration method presented in this paper makes use of a broad x-ray spectrum provided by commercial x-ray tubes. Gain and offset as the calibration parameters are obtained by a regression analysis that adjusts a simulated spectrum of deposited energies to a measured pulse-height spectrum. Besides the basic photon interactions such as Rayleigh scattering, Compton scattering and photo-electric absorption, the simulation takes into account the effect of pulse pileup, charge sharing and the electronic noise of the detector channels. We verify the method for different detector channels with the aid of a table-top setup, where we find the uncertainty of the keV-value of a calibrated threshold to be between 0.1 and 0.2 keV.

Tracing ram-pressure stripping with warm molecular hydrogen emission

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivanandam, Suresh; Rieke, Marcia J.; Rieke, George H., E-mail: sivanandam@dunlap.utoronto.ca

We use the Spitzer Infrared Spectrograph to study four infalling cluster galaxies with signatures of ongoing ram-pressure stripping. H{sub 2} emission is detected in all four, and two show extraplanar H{sub 2} emission. The emission usually has a warm (T ∼ 115-160 K) and a hot (T ∼ 400-600 K) component that is approximately two orders of magnitude less massive than the warm one. The warm component column densities are typically 10{sup 19} to 10{sup 20} cm{sup –2} with masses of 10{sup 6} to 10{sup 8} M {sub ☉}. The warm H{sub 2} is anomalously bright compared with normal star-formingmore » galaxies and therefore may be excited by ram-pressure. In the case of CGCG 97-073, the H{sub 2} is offset from the majority of star formation along the direction of the galaxy's motion in the cluster, suggesting that it is forming in the ram-pressure wake of the galaxy. Another galaxy, NGC 4522, exhibits a warm H{sub 2} tail approximately 4 kpc in length. These results support the hypothesis that H{sub 2} within these galaxies is shock-heated from the interaction with the intracluster medium. Stripping of dust is also a common feature of the galaxies. For NGC 4522, where the distribution of dust at 8 μm is well resolved, knots and ripples demonstrate the turbulent nature of the stripping process. The Hα and 24 μm luminosities show that most of the galaxies have star-formation rates comparable to similar mass counterparts in the field. Finally, we suggest a possible evolutionary sequence primarily related to the strength of ram-pressure that a galaxy experiences to explain the varied results observed in our sample.« less

Effects of static equilibrium and higher-order nonlinearities on rotor blade stability in hover

NASA Technical Reports Server (NTRS)

Crespodasilva, Marcelo R. M.; Hodges, Dewey H.

1988-01-01

The equilibrium and stability of the coupled elastic lead/lag, flap, and torsion motion of a cantilever rotor blade in hover are addressed, and the influence of several higher-order terms in the equations of motion of the blade is determined for a range of values of collective pitch. The blade is assumed to be untwisted and to have uniform properties along its span. In addition, chordwise offsets between its elastic, tension, mass, and aerodynamic centers are assumed to be negligible for simplicity. The aerodynamic forces acting on the blade are modeled using a quasi-steady, strip-theory approximation.

M/L, Hα Rotation Curves, and H I Gas Measurements for 329 Nearby Cluster and Field Spirals. III. Evolution in Fundamental Galaxy Parameters

NASA Astrophysics Data System (ADS)

Vogt, Nicole P.; Haynes, Martha P.; Giovanelli, Riccardo; Herter, Terry

2004-06-01

We have conducted a study of optical and H I properties of spiral galaxies (size, luminosity, Hα flux distribution, circular velocity, H I gas mass) to investigate causes (e.g., nature vs. nurture) for variation within the cluster environment. We find H I-deficient cluster galaxies to be offset in fundamental plane space, with disk scale lengths decreased by a factor of 25%. This may be a relic of early galaxy formation, caused by the disk coalescing out of a smaller, denser halo (e.g., higher concentration index) or by truncation of the hot gas envelope due to the enhanced local density of neighbors, although we cannot completely rule out the effect of the gas stripping process. The spatial extent of Hα flux and the B-band radius also decreases, but only in early-type spirals, suggesting that gas removal is less efficient within steeper potential wells (or that stripped late-type spirals are quickly rendered unrecognizable). We find no significant trend in stellar mass-to-light ratios or circular velocities with H I gas content, morphological type, or clustercentric radius, for star-forming spiral galaxies throughout the clusters. These data support the findings of a companion paper that gas stripping promotes a rapid truncation of star formation across the disk and could be interpreted as weak support for dark matter domination over baryons in the inner regions of spiral galaxies.

Hybrid molecular dynamics simulation for plasma induced damage analysis

NASA Astrophysics Data System (ADS)

Matsukuma, Masaaki

2016-09-01

In order to enable further device size reduction (also known as Moore's law) and improved power performance, the semiconductor industry is introducing new materials and device structures into the semiconductor fabrication process. Materials now include III-V compounds, germanium, cobalt, ruthenium, hafnium, and others. The device structure in both memory and logic has been evolving from planar to three dimensional (3D). One such device is the FinFET, where the transistor gate is a vertical fin made either of silicon, silicon-germanium or germanium. These changes have brought renewed interests in the structural damages caused by energetic ion bombardment of the fin sidewalls which are exposed to the ion flux from the plasma during the fin-strip off step. Better control of the physical damage of the 3D devices requires a better understanding of the damage formation mechanisms on such new materials and structures. In this study, the damage formation processes by ion bombardment have been simulated for Si and Ge substrate by Quantum Mechanics/Molecular Mechanics (QM/MM) hybrid simulations and compared to the results from the classical molecular dynamics (MD) simulations. In our QM/MM simulations, the highly reactive region in which the structural damage is created is simulated with the Density Functional based Tight Binding (DFTB) method and the region remote from the primary region is simulated using classical MD with the Stillinger-Weber and Moliere potentials. The learn on the fly method is also used to reduce the computational load. Hence our QM/MM simulation is much faster than the full QC-MD simulations and the original QM/MM simulations. The amorphous layers profile simulated with QM/MM have obvious differences in their thickness for silicon and germanium substrate. The profile of damaged structure in the germanium substrate is characterized by a deeper tail then in silicon. These traits are also observed in the results from the mass selected ion beam experiments. This observed damage profile dependence on species and substrate cannot be reproduced using classical MD simulations. While the Moliere potential is convenient to describe the interactions between halogens and other atoms, more accurate interatomic modeling such as DFTB method which takes the molecular orbitals into account should be utilized to make the simulations more realistic. Based on the simulations results, the damage formation scenario will be discussed.

A Comprehensive Biophysical Model of Ion and Water Transport in Plant Roots. I. Clarifying the Roles of Endodermal Barriers in the Salt Stress Response

PubMed Central

Foster, Kylie J.; Miklavcic, Stanley J.

2017-01-01

In this paper, we present a detailed and comprehensive mathematical model of active and passive ion and water transport in plant roots. Two key features are the explicit consideration of the separate, but interconnected, apoplastic, and symplastic transport pathways for ions and water, and the inclusion of both active and passive ion transport mechanisms. The model is used to investigate the respective roles of the endodermal Casparian strip and suberin lamellae in the salt stress response of plant roots. While it is thought that these barriers influence different transport pathways, it has proven difficult to distinguish their separate functions experimentally. In particular, the specific role of the suberin lamellae has been unclear. A key finding based on our simulations was that the Casparian strip is essential in preventing excessive uptake of Na+ into the plant via apoplastic bypass, with a barrier efficiency that is reflected by a sharp gradient in the steady-state radial distribution of apoplastic Na+ across the barrier. Even more significantly, this function cannot be replaced by the action of membrane transporters. The simulations also demonstrated that the positive effect of the Casparian strip of controlling Na+ uptake, was somewhat offset by its contribution to the osmotic stress component: a more effective barrier increased the detrimental osmotic stress effect. In contrast, the suberin lamellae were found to play a relatively minor, even non-essential, role in the overall response to salt stress, with the presence of the suberin lamellae resulting in only a slight reduction in Na+ uptake. However, perhaps more significantly, the simulations identified a possible role of suberin lamellae in reducing plant energy requirements by acting as a physical barrier to preventing the passive leakage of Na+ into endodermal cells. The model results suggest that more and particular experimental attention should be paid to the properties of the Casparian strip when assessing the salt tolerance of different plant varieties and species. Indeed, the Casparian strip appears to be a more promising target for plant breeding and plant genetic engineering efforts than the suberin lamellae for the goal of improving salt tolerance. PMID:28804493

Fast bender actuators for fish-like aquatic robots

NASA Astrophysics Data System (ADS)

McGovern, S. T.; Spinks, G. M.; Xi, B.; Alici, G.; Truong, V.; Wallace, G. G.

2008-03-01

Small, highly-mobile "swimming" robots are desired for underwater monitoring operations, including pollution detection, video mapping and other tasks. Actuator materials of all types are of interest for any application where space is limited. This constraint certainly applies to the small-scale swimming robot, where multiple small actuators are needed for forward/backward propulsion, steering and diving/surfacing. A number of previous studies have demonstrated propulsion of floating objects using IPMC type polymer actuators [1-3] or piezoceramic actuators [4, 5]. Here, we show how propulsion is also possible using a multi-layer polypyrrole bimorph actuator. The actuator is based on our previously published work showing very fast resonance actuation in polypyrrole bending-type actuators [6]. The bending actuator is a tri-layer structure, in which the gold-PVDF (porous poly(vinylidene fluoride) membrane) substrate was coated on both sides with polypyrrole layers to form an electrochemical cell. Polypyrrole films on gold coated PVDF were grown galvanostatically at a current density of 0.10 mA/cm2 for 12 hours from propylene carbonate (PC) solution containing 0.1 M Li+TFSI-, 0.1 M pyrrole and 1% (w/w) water. The polypyrrole deposited PVDF was thoroughly rinsed with acetone and stored in 0.1 M Li+TFSI- / PC solution. The edges of the bulk film were trimmed off and the bending actuators were prepared as rectangular strips typically 2mm wide and 25 mm long. These actuators gave fast operation in air (to 90 Hz), and were utilised as active flexural joints on the tail fin of a fishshaped floating "boat". The actuators were attached to a simple truncated shaped fin and the deflection angle was analysed in both air and liquid for excitation with +/- 1V square wave at a range of frequencies. The mechanical resonance of the fin was seen to be 4.5 Hz in air and 0.45 Hz in PC, which gave deflection angles of approximately 60° and 55° respectively. The boat contained a battery, receiver unit and electronic circuit attached to the actuator fin assembly. Thus, the boat could be operated by remote control, and by varying the frequency and duty cycle applied to the actuator, the speed and direction of the boat could be controlled. The boat had a turning circle as small as 15 cm in radius and a maximum speed of 2m/min when operating with a tail frequency of approximately 0.7 Hz. The efficiency of the flapping tail fin was analysed and it was seen that operation at this frequency corresponded with a Strouhal number in the optimal range.

6. Photocopy of photograph, U.S. Army, ca. 1955 (original print ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. Photocopy of photograph, U.S. Army, ca. 1955 (original print located at Rocky Mountain Arsenal, Commerce City, Colorado). AERIAL VIEW OF BUILDING 1611. VIEW TO NORTHEAST. 'THIS IS THE HONEST JOHN WARHEAD DEMILITARIZATION PLANT. THE DEMILITARIZATION PROCESS CONSISTS OF STRIPPING AND OPENING THE WARHEAD MANUALLY AND DOWNLOADING THE M139 BOMBLETS ONTO A CONVEYOR WHICH CARRIES THEM THROUGH A PUNCH, DRAIN AND RINSE MACHINE INTO A ROTARY RETORT DEACTIVATION FURNACE WHERE THE BURSTER IS BURNED. THE BOMBLET SHELLS, WHICH ARE ALUMINUM, ARE THEN CONVEYED TO A DECONTAMINATION FURNACE WHERE THEY ARE MELTED AND CAST INTO INGOTS. THE GB, WHICH IS COLLECTED IN THE PUNCH, DRAIN AND RINSE MACHINE, IS CONDUCTED TO A STORAGE TANK AND, ULTIMATELY, IS NEUTRALIZED ... - Rocky Mountain Arsenal, Ammunition Demolition Building-Tail Fin Storage & Assembly, 2750 feet South of Ninth Avenue; 3480 feet East of D Street, Commerce City, Adams County, CO

The sensitivity of harassment to orbit: mass loss from early-type dwarfs in galaxy clusters

NASA Astrophysics Data System (ADS)

Smith, R.; Sánchez-Janssen, R.; Beasley, M. A.; Candlish, G. N.; Gibson, B. K.; Puzia, T. H.; Janz, J.; Knebe, A.; Aguerri, J. A. L.; Lisker, T.; Hensler, G.; Fellhauer, M.; Ferrarese, L.; Yi, S. K.

2015-12-01

We conduct a comprehensive numerical study of the orbital dependence of harassment on early-type dwarfs consisting of 168 different orbits within a realistic, Virgo-like cluster, varying in eccentricity and pericentre distance. We find harassment is only effective at stripping stars or truncating their stellar discs for orbits that enter deep into the cluster core. Comparing to the orbital distribution in cosmological simulations, we find that the majority of the orbits (more than three quarters) result in no stellar mass loss. We also study the effects on the radial profiles of the globular cluster systems of early-type dwarfs. We find these are significantly altered only if harassment is very strong. This suggests that perhaps most early-type dwarfs in clusters such as Virgo have not suffered any tidal stripping of stars or globular clusters due to harassment, as these components are safely embedded deep within their dark matter halo. We demonstrate that this result is actually consistent with an earlier study of harassment of dwarf galaxies, despite the apparent contradiction. Those few dwarf models that do suffer stellar stripping are found out to the virial radius of the cluster at redshift = 0, which mixes them in with less strongly harassed galaxies. However when placed on phase-space diagrams, strongly harassed galaxies are found offset to lower velocities compared to weakly harassed galaxies. This remains true in a cosmological simulation, even when haloes have a wide range of masses and concentrations. Thus phase-space diagrams may be a useful tool for determining the relative likelihood that galaxies have been strongly or weakly harassed.

Mechanosensation in an adipose fin

PubMed Central

2016-01-01

Adipose fins are found on approximately 20% of ray-finned fish species. The apparently rudimentary anatomy of adipose fins inspired a longstanding hypothesis that these fins are vestigial and lack function. However, adipose fins have evolved repeatedly within Teleostei, suggesting adaptive function. Recently, adipose fins were proposed to function as mechanosensors, detecting fluid flow anterior to the caudal fin. Here we test the hypothesis that adipose fins are mechanosensitive in the catfish Corydoras aeneus. Neural activity, recorded from nerves that innervate the fin, was shown to encode information on both movement and position of the fin membrane, including the magnitude of fin membrane displacement. Thus, the adipose fin of C. aeneus is mechanosensitive and has the capacity to function as a ‘precaudal flow sensor’. These data force re-evaluation of adipose fin clipping, a common strategy for tagging fishes, and inform hypotheses of how function evolves in novel vertebrate appendages. PMID:26984621

Mechanosensation in an adipose fin.

PubMed

Aiello, Brett R; Stewart, Thomas A; Hale, Melina E

2016-03-16

Adipose fins are found on approximately 20% of ray-finned fish species. The apparently rudimentary anatomy of adipose fins inspired a longstanding hypothesis that these fins are vestigial and lack function. However, adipose fins have evolved repeatedly within Teleostei, suggesting adaptive function. Recently, adipose fins were proposed to function as mechanosensors, detecting fluid flow anterior to the caudal fin. Here we test the hypothesis that adipose fins are mechanosensitive in the catfish Corydoras aeneus. Neural activity, recorded from nerves that innervate the fin, was shown to encode information on both movement and position of the fin membrane, including the magnitude of fin membrane displacement. Thus, the adipose fin of C. aeneus is mechanosensitive and has the capacity to function as a 'precaudal flow sensor'. These data force re-evaluation of adipose fin clipping, a common strategy for tagging fishes, and inform hypotheses of how function evolves in novel vertebrate appendages. © 2016 The Author(s).

The origins of adipose fins: an analysis of homoplasy and the serial homology of vertebrate appendages.

PubMed

Stewart, Thomas A; Smith, W Leo; Coates, Michael I

2014-04-22

Adipose fins are appendages found on the dorsal midline between the dorsal and caudal fins in more than 6000 living species of teleost fishes. It has been consistently argued that adipose fins evolved once and have been lost repeatedly across teleosts owing to limited function. Here, we demonstrate that adipose fins originated repeatedly by using phylogenetic and anatomical evidence. This suggests that adipose fins are adaptive, although their function remains undetermined. To test for generalities in the evolution of form in de novo vertebrate fins, we studied the skeletal anatomy of adipose fins across 620 species belonging to 186 genera and 55 families. Adipose fins have repeatedly evolved endoskeletal plates, anterior dermal spines and fin rays. The repeated evolution of fin rays in adipose fins suggests that these fins can evolve new tissue types and increased structural complexity by expressing fin-associated developmental modules in these new territories. Patterns of skeletal elaboration differ between the various occurrences of adipose fins and challenge prevailing hypotheses for vertebrate fin origin. Adipose fins represent a powerful and, thus far, barely studied model for exploring the evolution of vertebrate limbs and the roles of adaptation and generative biases in morphological evolution.

The origins of adipose fins: an analysis of homoplasy and the serial homology of vertebrate appendages

PubMed Central

Stewart, Thomas A.; Smith, W. Leo; Coates, Michael I.

2014-01-01

Adipose fins are appendages found on the dorsal midline between the dorsal and caudal fins in more than 6000 living species of teleost fishes. It has been consistently argued that adipose fins evolved once and have been lost repeatedly across teleosts owing to limited function. Here, we demonstrate that adipose fins originated repeatedly by using phylogenetic and anatomical evidence. This suggests that adipose fins are adaptive, although their function remains undetermined. To test for generalities in the evolution of form in de novo vertebrate fins, we studied the skeletal anatomy of adipose fins across 620 species belonging to 186 genera and 55 families. Adipose fins have repeatedly evolved endoskeletal plates, anterior dermal spines and fin rays. The repeated evolution of fin rays in adipose fins suggests that these fins can evolve new tissue types and increased structural complexity by expressing fin-associated developmental modules in these new territories. Patterns of skeletal elaboration differ between the various occurrences of adipose fins and challenge prevailing hypotheses for vertebrate fin origin. Adipose fins represent a powerful and, thus far, barely studied model for exploring the evolution of vertebrate limbs and the roles of adaptation and generative biases in morphological evolution. PMID:24598422

First description of a musculoskeletal linkage in an adipose fin: innovations for active control in a primitively passive appendage

PubMed Central

Stewart, Thomas A.; Hale, Melina E.

2013-01-01

Adipose fins are enigmatic appendages found between the dorsal and caudal fins of some teleostean fishes. Long thought to be vestigial, degenerate second dorsal fins, remnants of the primitive gnathostome condition, adipose fins have since been recognized as novel morphologies. Unique among the fins of extant fishes, adipose fins have uniformly been described as passive structures, with no associated musculature. Here we provide the first description of a musculoskeletal linkage in an adipose fin, identified in the sun catfish Horabagrus brachysoma. Modified supracarinalis posterior muscles insert from the dorsal midline anterior to the adipose fin by tendons onto the fin base. An additional pair of posterior adipose-fin muscles also inserts upon the fin base and lay posterolateral to the fin, superficial to the axial muscle. This musculoskeletal linkage is an evolutionary innovation, a novel mechanism for controlling adipose-fin movement. These muscles appear to exemplify two approaches by which fins evolve to be actively controlled. We hypothesize that the anterior muscles arose through co-option of an existing fin linkage, while the posterior muscles originated as de novo fin muscles. These findings present adipose fins as a rich system within which to explore the evolution of novel vertebrate appendages. PMID:23135670

Fish locomotion: kinematics and hydrodynamics of flexible foil-like fins

NASA Astrophysics Data System (ADS)

Lauder, George V.; Madden, Peter G. A.

2007-11-01

The fins of fishes are remarkable propulsive devices that appear at the origin of fishes about 500 million years ago and have been a key feature of fish evolutionary diversification. Most fish species possess both median (midline) dorsal, anal, and caudal fins as well as paired pectoral and pelvic fins. Fish fins are supported by jointed skeletal elements, fin rays, that in turn support a thin collagenous membrane. Muscles at the base of the fin attach to and actuate each fin ray, and fish fins thus generate their own hydrodynamic wake during locomotion, in addition to fluid motion induced by undulation of the body. In bony fishes, the jointed fin rays can be actively deformed and the fin surface can thus actively resist hydrodynamic loading. Fish fins are highly flexible, exhibit considerable deformation during locomotion, and can interact hydrodynamically during both propulsion and maneuvering. For example, the dorsal and anal fins shed a vortex wake that greatly modifies the flow environment experienced by the tail fin. New experimental kinematic and hydrodynamic data are presented for pectoral fin function in bluegill sunfish. The highly flexible sunfish pectoral fin moves in a complex manner with two leading edges, a spanwise wave of bending, and substantial changes in area through the fin beat cycle. Data from scanning particle image velocimetry (PIV) and time-resolved stereo PIV show that the pectoral fin generates thrust throughout the fin beat cycle, and that there is no time of net drag. Continuous thrust production is due to fin flexibility which enables some part of the fin to generate thrust at all times and to smooth out oscillations that might arise at the transition from outstroke to instroke during the movement cycle. Computational fluid dynamic analyses of sunfish pectoral fin function corroborate this conclusion. Future research on fish fin function will benefit considerably from close integration with studies of robotic model fins.

Fin development in stream- and hatchery-reared Atlantic salmon

USGS Publications Warehouse

Pelis, Ryan M.; McCormick, S.D.

2003-01-01

To determine the effect of development and environment on fin growth, we measured fin lengths of juvenile Atlantic salmon (Salmo salar) from two hatcheries (August, October and April-May), stream-reared fish (July and October) stocked as fry into two tributaries, and smelts from the main stem of the Connecticut River (May). For stream-reared parr, there was a linear relationship between the dorsal, caudal and anal fins with fork length, while the pectoral, pelvic and adipose fins exhibited a curvilinear relationship with fork length. Parr from a high gradient stream had larger caudal fins than fish from a low gradient stream, but other fins did not differ. Regression lines for the fins of stream-reared smelts were all linear when fin length was regressed against fork length. Stream-reared parr had larger pectoral, pelvic and anal fins than smolts of similar size while dorsal and caudal fin lengths did not differ. Regression equations formulated using the fins of stream-reared parr were used to calculate the percent difference (100 x observed fin length/expected) in fin lengths between stream- and hatchery-reared parr. The pelvic, adipose, caudal and anal fins of hatchery-reared parr showed no signs of degeneration by the first sampling period 7 months after hatching, whereas degeneration in the pectoral (13-20%) and dorsal (15-18%) fins was evident at this time. By the end of the study, degeneration was present in every fin except the adipose, with the pectoral (35-65%) and dorsal (32-58%) fins exhibiting the greatest amount of fin loss. All fins of hatchery-reared parr became shorter with time. There were minor differences in fin degeneration among parr from the two hatcheries, but the overall pattern of decreasing fin size was similar, indicating a common cause of fin degeneration. Comparison of stream- and hatchery-reared fish is a valuable means of determining the impact of captive environments on fin growth.

Fins effectiveness and efficiency with position function of rhombus sectional area in unsteady condition

NASA Astrophysics Data System (ADS)

Nugroho, Tito Dwi; Purwadi, P. K.

2017-01-01

The function of the fin is to extend surfaces so that objects fitted with fin can remove the heat to the surrounding environment so that the cooling process can take place more quickly. The purpose of this study is to calculate and determine the effect of (a) the convective heat transfer coefficient of fluid on the value of the fin on the efficiency and effectiveness of non-steady state, and (b) the fin material to the value of the fins on the efficiency and effectiveness of non-steady state. The studied fins are in the form of straight fins with rhombus sectional area which is a function of position x with the short diagonal length of D1 and D2 as long diagonal length, L as fin's length and α as fin's tilt angle. Research solved numerical computation, using a finite difference method on the explicit way. At first, the fin has the same initial temperature with essentially temperature Ti = Tb, then abruptly fin conditioned on fluid temperature environment T∞. Fin's material is assumed with uniform properties, does not change with changes in temperature, and fin does not change the shape and volume during the process. The temperature of the fluid around the fins and the value of the convective heat transfer coefficient are permanently constant, and there is no energy generation in the fin. Fin's heat transfer conduction only take place in one direction, namely in the direction perpendicular to the fin base (or x-direction). The entire surface of the fin makes the process of heat transfer to a fluid environment around the fins. The results show that (a) the greater the value of heat transfer coefficient of convection h, the smaller the efficiency fin and effectiveness fins (b) In circumstances of unsteady state, the efficiency and effectivity influenced by the value of density, specific heat, heat transfer coefficient of conduction and thermal diffusivity fin material.

The Grism Lens-Amplified Survey from Space (GLASS). VIII. The Influence of the Cluster Properties on Hα Emitter Galaxies at 0.3 < z < 0.7

NASA Astrophysics Data System (ADS)

Vulcani, Benedetta; Treu, Tommaso; Nipoti, Carlo; Schmidt, Kasper B.; Dressler, Alan; Morshita, Takahiro; Poggianti, Bianca M.; Malkan, Matthew; Hoag, Austin; Bradač, Marusa; Abramson, Louis; Trenti, Michele; Pentericci, Laura; von der Linden, Anja; Morris, Glenn; Wang, Xin

2017-03-01

Exploiting the data of the Grism Lens-Amplified Survey from Space (GLASS), we characterize the spatial distribution of star formation in 76 highly active star-forming galaxies in 10 clusters at 0.3< z< 0.7. All of these galaxies are likely restricted to first infall. In a companion paper, we contrast the properties of field and cluster galaxies, whereas here we correlate the properties of Hα emitters to a number of tracers of the cluster environment to investigate its role in driving galaxy transformations. Hα emitters are found in the clusters out to 0.5 virial radii, the maximum radius covered by GLASS. The peak of the Hα emission is offset with respect to the peak of the UV continuum. We decompose these offsets into a radial and a tangential component. The radial component points away from the cluster center in 60% of the cases, with 95% confidence. The decompositions agree with cosmological simulations; that is, the Hα emission offset correlates with galaxy velocity and ram-pressure stripping signatures. Trends between Hα emitter properties and surface mass density distributions and X-ray emissions emerge only for unrelaxed clusters. The lack of strong correlations with the global environment does not allow us to identify a unique environmental effect originating from the cluster center. In contrast, correlations between Hα morphology and local number density emerge. We conclude that local effects, uncorrelated to the cluster-centric radius, play a more important role in shaping galaxy properties.

Rotor blades for turbine engines

DOEpatents

Piersall, Matthew R; Potter, Brian D

2013-02-12

A tip shroud that includes a plurality of damping fins, each damping fin including a substantially non-radially-aligned surface that is configured to make contact with a tip shroud of a neighboring rotor blade. At least one damping fin may include a leading edge damping fin and at least one damping fin may include a trailing edge damping fin. The leading edge damping fin may be configured to correspond to the trailing edge damping fin.

50 CFR 600.1204 - Shark finning; possession at sea and landing of shark fins.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 12 2013-10-01 2013-10-01 false Shark finning; possession at sea and landing of shark fins. 600.1204 Section 600.1204 Wildlife and Fisheries FISHERY CONSERVATION AND... PROVISIONS Shark Finning § 600.1204 Shark finning; possession at sea and landing of shark fins. (a)(1) No...

50 CFR 600.1204 - Shark finning; possession at sea and landing of shark fins.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 10 2011-10-01 2011-10-01 false Shark finning; possession at sea and landing of shark fins. 600.1204 Section 600.1204 Wildlife and Fisheries FISHERY CONSERVATION AND... PROVISIONS Shark Finning § 600.1204 Shark finning; possession at sea and landing of shark fins. (a)(1) No...

50 CFR 600.1204 - Shark finning; possession at sea and landing of shark fins.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 12 2012-10-01 2012-10-01 false Shark finning; possession at sea and landing of shark fins. 600.1204 Section 600.1204 Wildlife and Fisheries FISHERY CONSERVATION AND... PROVISIONS Shark Finning § 600.1204 Shark finning; possession at sea and landing of shark fins. (a)(1) No...

50 CFR 600.1204 - Shark finning; possession at sea and landing of shark fins.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 12 2014-10-01 2014-10-01 false Shark finning; possession at sea and landing of shark fins. 600.1204 Section 600.1204 Wildlife and Fisheries FISHERY CONSERVATION AND... PROVISIONS Shark Finning § 600.1204 Shark finning; possession at sea and landing of shark fins. (a)(1) No...

Kinematics of ribbon-fin locomotion in the bowfin, Amia calva.

PubMed

Jagnandan, Kevin; Sanford, Christopher P

2013-12-01

An elongated dorsal and/or anal ribbon-fin to produce forward and backward propulsion has independently evolved in several groups of fishes. In these fishes, fin ray movements along the fin generate a series of waves that drive propulsion. There are no published data on the use of the dorsal ribbon-fin in the basal freshwater bowfin, Amia calva. In this study, frequency, amplitude, wavelength, and wave speed along the fin were measured in Amia swimming at different speeds (up to 1.0 body length/sec) to understand how the ribbon-fin generates propulsion. These wave properties were analyzed to (1) determine whether regional specialization occurs along the ribbon-fin, and (2) to reveal how the undulatory waves are used to control swimming speed. Wave properties were also compared between swimming with sole use of the ribbon-fin, and swimming with simultaneous use of the ribbon and pectoral fins. Statistical analysis of ribbon-fin kinematics revealed no differences in kinematic patterns along the ribbon-fin, and that forward propulsive speed in Amia is controlled by the frequency of the wave in the ribbon-fin, irrespective of the contribution of the pectoral fin. This study is the first kinematic analysis of the ribbon-fin in a basal fish and the model species for Amiiform locomotion, providing a basis for understanding ribbon-fin locomotion among a broad range of teleosts. © 2013 Wiley Periodicals, Inc.

Role of Pectoral Fin Flexibility in Robotic Fish Performance

NASA Astrophysics Data System (ADS)

Bazaz Behbahani, Sanaz; Tan, Xiaobo

2017-08-01

Pectoral fins play a vital role in the maneuvering and locomotion of fish, and they have become an important actuation mechanism for robotic fish. In this paper, we explore the effect of flexibility of robotic fish pectoral fins on the robot locomotion performance and mechanical efficiency. A dynamic model for the robotic fish is presented, where the flexible fin is modeled as multiple rigid elements connected via torsional springs and dampers. Blade element theory is used to capture the hydrodynamic force on the fin. The model is validated with experimental results obtained on a robotic fish prototype, equipped with 3D-printed fins of different flexibility. The model is then used to analyze the impacts of fin flexibility and power/recovery stroke speed ratio on the robot swimming speed and mechanical efficiency. It is found that, in general, flexible fins demonstrate advantages over rigid fins in speed and efficiency at relatively low fin-beat frequencies, while rigid fins outperform flexible fins at higher frequencies. For a given fin flexibility, the optimal frequency for speed performance differs from the optimal frequency for mechanical efficiency. In addition, for any given fin, there is an optimal power/recovery stroke speed ratio, typically in the range of 2-3, that maximizes the speed performance. Overall, the presented model offers a promising tool for fin flexibility and gait design, to achieve speed and efficiency objectives for robotic fish actuated with pectoral fins.

How fish swim: flexible fin thrusters as an EAP platform

NASA Astrophysics Data System (ADS)

Lauder, George V.

2007-04-01

Fish are capable of remarkable locomotor performance and use their fins extensively for both propulsion and maneuvering. Recent interest in using fishes as inspiration for the design of a new generation of autonomous underwater vehicles has prompted both new experimental studies of fish locomotor function and efforts to use electroactive polymers (EAP) as actuators in fish-inspired propulsive devices. The fins of fishes allow precise control over body position and vectoring of thrust during propulsion and maneuvering. Recent experimental studies of fish locomotion have revealed that fins exhibit much greater flexibility than previously suspected and that there is considerable deformation of the fin surface during locomotion. The fins of the large group known as ray-finned fishes are supported by fin rays, which have a bilaminar structure that allows active curvature control of the ray and fin surface by the fin musculature. Fish have up to seven different fins, and these fins may interact with each other hydrodynamically during locomotion. Fish fins provide an excellent test platform for the use of electroactive polymer actuators as the frequency of movement is typically less than 5 Hz, and fin muscle strains typically range from 2 to 10%. Recent developments of biorobotic fish pectoral fins actuated with EAP are reviewed.

Lessons from the first dorsal fin in atheriniforms—A new mode of dorsal fin development and its phylogenetic implications

PubMed Central

Richter, Philipp

2017-01-01

Abstract The median fins in extant actinopterygians are the product of millions of years of evolution. During this time, different developmental patterns for the dorsal and anal fins emerged leading to a high variation in median fin morphology and ontogeny. In this study, the development of anal and dorsal fins in atheriniforms is described and its consequences for the current phylogenetic hypothesis are discussed. Developmental series of five atheriniform species were investigated using clearing and staining as well as antibody staining. The skeletal elements of the second dorsal fin and the anal fin emerge in a bidirectional pattern. The first dorsal fin, however, arises separately in front of the second dorsal fin after this one is almost completely formed. The pterygiophores of the first dorsal fin, including the interdorsal pterygiophores, develop from caudal to rostral, but the fin‐spines of the first dorsal fin form in the opposite direction. This new mode of fin development has been found in all examined atheriniform species with two dorsal fins. Several morphological characters of atheriniforms, including interdorsal pterygiophores, are also found in one other taxon: the Mugiliformes. Thus, several dorsal fin characteristics may provide evidence for a closer relationship of these two taxa. PMID:28370120

Effect of Fin Passage Length on Optimization of Cylinder Head Cooling Fins

NASA Technical Reports Server (NTRS)

Siegel, R.; Graham, R. W.

1977-01-01

The heat transfer performance of baffled cooling fins on cylinder heads of small, air-cooled, general-aviation aircraft engines was analyzed to determine the potential for improving cooling fin design. Flow baffles were assumed to be installed tightly against the fin end edges, an ideal baffle configuration for guiding all flow between the fins. A rectangular flow passage is thereby formed between each set of two adjacent fins, the fin base surface, and the baffle. These passages extend around each side of the cylinder head, and the cooling air absorbs heat as it flows within them. For each flow passage length, the analysis was concerned with optimizing fin spacing and thickness to achieve the best heat transfer for each fin width. Previous literature has been concerned mainly with maximizing the local fin conductance and has not considered the heating of the gas in the flow direction, which leads to higher wall temperatures at the fin passage exits. If the fins are close together, there is a large surface area, but the airflow is restricted.

The effect of fin ray flexural rigidity on the propulsive forces generated by a biorobotic fish pectoral fin.

PubMed

Tangorra, James L; Lauder, George V; Hunter, Ian W; Mittal, Rajat; Madden, Peter G A; Bozkurttas, Meliha

2010-12-01

A biorobotic pectoral fin was developed and used to study how the flexural rigidities of fin rays within a highly deformable fish fin affect the fin's propulsive forces. The design of the biorobotic fin was based on a detailed analysis of the pectoral fin of the bluegill sunfish (Lepomis macrochirus). The biorobotic fin was made to execute the kinematics used by the biological fin during steady swimming, and to have structural properties that modeled those of the biological fin. This resulted in an engineered fin that had a similar interaction with the water as the biological fin and that created close approximations of the three-dimensional motions, flows, and forces produced by the sunfish during low speed, steady swimming. Experimental trials were conducted during which biorobotic fins of seven different stiffness configurations were flapped at frequencies from 0.5 to 2.0 Hz in flows with velocities that ranged from 0 to 270 mm s(-1). During these trials, thrust and lift forces were measured, kinematics were recorded in three dimensions, and digital particle image velocimetry was used to evaluate flow hydrodynamics. The results of the trials revealed that slight changes to the fin's mechanical properties or to the operating conditions can have significant impact on the direction, magnitude and time course of the propulsive forces. In general, the magnitude of the 2-D (thrust and lift) propulsive force scaled with fin ray stiffness, and increased as the fin's flapping speed increased or as the velocity of the flow decreased.

Mapping interactions between the RNA chaperone FinO and its RNA targets

PubMed Central

Arthur, David C.; Tsutakawa, Susan; Tainer, John A.; Frost, Laura S.; Glover, J. N. Mark

2011-01-01

Bacterial conjugation is regulated by two-component repression comprising the antisense RNA FinP, and its protein co-factor FinO. FinO mediates base-pairing of FinP to the 5′-untranslated region (UTR) of traJ mRNA, which leads to translational inhibition of the transcriptional activator TraJ and subsequent down regulation of conjugation genes. Yet, little is known about how FinO binds to its RNA targets or how this interaction facilitates FinP and traJ mRNA pairing. Here, we use solution methods to determine how FinO binds specifically to its minimal high affinity target, FinP stem–loop II (SLII), and its complement SLIIc from traJ mRNA. Ribonuclease footprinting reveals that FinO contacts the base of the stem and the 3′ single-stranded tails of these RNAs. The phosphorylation or oxidation of the 3′-nucleotide blocks FinO binding, suggesting FinO binds the 3′-hydroxyl of its RNA targets. The collective results allow the generation of an energy-minimized model of the FinO–SLII complex, consistent with small-angle X-ray scattering data. The repression complex model was constrained using previously reported cross-linking data and newly developed footprinting results. Together, these data lead us to propose a model of how FinO mediates FinP/traJ mRNA pairing to down regulate bacterial conjugation. PMID:21278162

A comparison of pectoral fin ray morphology and its impact on fin ray flexural stiffness in labriform swimmers.

PubMed

Aiello, Brett R; Hardy, Adam R; Cherian, Chery; Olsen, Aaron M; Orsbon, Courtney P; Hale, Melina E; Westneat, Mark W

2018-04-25

The organization of tissues in appendages often affects their mechanical properties and function. In the fish family Labridae, swimming behavior is associated with pectoral fin flexural stiffness and morphology, where fins range on a continuum from stiff to relatively flexible fins. Across this diversity, pectoral fin flexural stiffness decreases exponentially along the length of any given fin ray, and ray stiffness decreases along the chord of the fin from the leading to trailing edge. In this study, we examine the morphological properties of fin rays, including the effective modulus in bending (E), second moment of area (I), segmentation, and branching patterns, and their impact on fin ray stiffness. We quantify intrinsic pectoral fin ray stiffness in similarly sized fins of two closely related species that employ fins of divergent mechanics, the flapping Gomphosus varius and the rowing Halichoeres bivittatus. While segmentation patterns and E were similar between species, measurements of I and the number of fin ray branch nodes were greater in G. varius than in H. bivittatus. A multiple regression model found that of these variables, I was always significantly correlated with fin ray flexural stiffness and that variation in I always explained the majority of the variation in flexural stiffness. Thus, while most of the morphological variables quantified in this study correlate with fin ray flexural stiffness, second moment of area is the greatest factor contributing to variation in flexural stiffness. Further, interspecific variation in fin ray branching pattern could be used as a means of tuning the effective stiffness of the fin webbing to differences in swimming behavior and hydrodynamics. The comparison of these results to other systems begins to unveil fundamental morphological features of biological beams and yields insight into the role of mechanical properties in fin deformation for aquatic locomotion. © 2018 Wiley Periodicals, Inc.

Hydrodynamic function of dorsal fins in spiny dogfish and bamboo sharks during steady swimming.

PubMed

Maia, Anabela; Lauder, George V; Wilga, Cheryl D

2017-11-01

A key feature of fish functional design is the presence of multiple fins that allow thrust vectoring and redirection of fluid momentum to contribute to both steady swimming and maneuvering. A number of previous studies have analyzed the function of dorsal fins in teleost fishes in this context, but the hydrodynamic function of dorsal fins in freely swimming sharks has not been analyzed, despite the potential for differential functional roles between the anterior and posterior dorsal fins. Previous anatomical research has suggested a primarily stabilizing role for shark dorsal fins. We evaluated the generality of this hypothesis by using time-resolved particle image velocimetry to record water flow patterns in the wake of both the anterior and posterior dorsal fins in two species of freely swimming sharks: bamboo sharks ( Chiloscyllium plagiosum ) and spiny dogfish ( Squalus acanthias ). Cross-correlation analysis of consecutive images was used to calculate stroke-averaged mean longitudinal and lateral velocity components, and vorticity. In spiny dogfish, we observed a velocity deficit in the wake of the first dorsal fin and flow acceleration behind the second dorsal fin, indicating that the first dorsal fin experiences net drag while the second dorsal fin can aid in propulsion. In contrast, the wake of both dorsal fins in bamboo sharks displayed increased net flow velocity in the majority of trials, reflecting a thrust contribution to steady swimming. In bamboo sharks, fluid flow in the wake of the second dorsal fin had higher absolute average velocity than that for first dorsal fin, and this may result from a positive vortex interaction between the first and second dorsal fins. These data suggest that the first dorsal fin in spiny dogfish has primarily a stabilizing function, while the second dorsal fin has a propulsive function. In bamboo sharks, both dorsal fins can contribute thrust and should be considered as propulsive adjuncts to the body during steady swimming. The function of shark dorsal fins can thus differ considerably among fins and species, and is not limited to a stabilizing role. © 2017. Published by The Company of Biologists Ltd.

Functional morphology and hydrodynamics of backward swimming in bluegill sunfish, Lepomis macrochirus.

PubMed

Flammang, Brooke E; Lauder, George V

2016-10-01

Most teleost fishes, like the bluegill sunfish Lepomis macrochirus, have multiple flexible fins that are used as modifiable control surfaces. This helps to make fish highly maneuverable, permitting behaviors like reversing direction of motion and swimming backwards without having to rotate body position. To answer the question of how fish swim backwards we used high-speed videography and electromyography to determine the kinematics and muscle activity necessary to produce reverse-direction propulsion in four bluegill sunfish. We found that, in contrast to slow forward swimming, low-speed backward swimming is a multi-fin behavior, utilizing the pectoral, dorsal, anal, and caudal fins. The pectoral fins alternate beats, each fin broadly flaring on the outstroke and feathered on the instroke. The dorsal fin and dorsal portion of the caudal fin move out of phase as do the anal fin and ventral portion of the caudal fin. Electromyography of muscles in the pectoral, dorsal, anal, and caudal fins demonstrated bilateral activation when these fins changed direction, suggesting that fins are stiffened at this time. In addition to backward propulsion by the pectoral fins, particle image velocimetry revealed that the dorsal and anal fins are capable of producing reverse momentum jets to propel the fish backward. Because teleost fishes are statically unstable, locomotion at slow speeds requires precise fin control to adequately balance torques produced about the center of mass. Therefore, the kinematics of backward swimming may be the result of compensation for rolling, pitching, and yawning instability. We suggest that asymmetric pectoral fin activity with feathering during adduction balances rolling instability. The ventral to dorsal undulatory wave on the caudal fin controls pitch instability and yaw instability encountered from pectoral-driven backward locomotion. Thrust generation from the dorsal and anal fins decreases the destabilizing effect of the long moment arm of the tail in backward swimming. Thus, backward locomotion at slow speed is not simply the reverse of slow forward swimming. Copyright © 2016 Elsevier GmbH. All rights reserved.

Modeling a Thermoelectric Generator Applied to Diesel Automotive Heat Recovery

NASA Astrophysics Data System (ADS)

Espinosa, N.; Lazard, M.; Aixala, L.; Scherrer, H.

2010-09-01

Thermoelectric generators (TEGs) are outstanding devices for automotive waste heat recovery. Their packaging, lack of moving parts, and direct heat to electrical conversion are the main benefits. Usually, TEGs are modeled with a constant hot-source temperature. However, energy in exhaust gases is limited, thus leading to a temperature decrease as heat is recovered. Therefore thermoelectric properties change along the TEG, affecting performance. A thermoelectric generator composed of Mg2Si/Zn4Sb3 for high temperatures followed by Bi2Te3 for low temperatures has been modeled using engineering equation solver (EES) software. The model uses the finite-difference method with a strip-fins convective heat transfer coefficient. It has been validated on a commercial module with well-known properties. The thermoelectric connection and the number of thermoelements have been addressed as well as the optimum proportion of high-temperature material for a given thermoelectric heat exchanger. TEG output power has been estimated for a typical commercial vehicle at 90°C coolant temperature.

Experimental Investigation on Effect of Fin Shape on the Thermal-Hydraulic Performance of Compact Fin-and-Tube Heat Exchangers

NASA Astrophysics Data System (ADS)

Moorthy, P.; Oumer, A. N.; Ishak, M.

2018-03-01

The aim of this paper is to investigate the effect of fin shapes on the performance of compact finned flat tube heat exchangers. Three types of fin shapes namely plain, wavy, and rectangular grooved fins attached to three by three arrays of flat tube banks were considered. Moreover, the tubes were deployed in in-line and staggered arrangements. In addition to the fin shapes, the air velocity and the tube inclination angles were varied and the thermal-hydraulic performance was analysed. On the other hand, the temperatures at the tube surfaces were kept constant to produce constant heat flux throughout the study. The results showed that as flowrate increases, the heat transfer increases, however, the friction factor decreases. Staggered arrangement produces higher heat transfer and friction factor than inline fin. Moreover, the rectangular fin is the best in terms of high heat transfer however the drawback of high friction factor leads the fin to have the least efficiency of all. On the other hand, plain fin had the least heat transfer performance however the highest efficiency was achieved. Therefore, plain fin should be used when efficiency is prioritized and rectangular fin when high heat transfer is desired.

The Grism Lens-Amplified Survey from Space (GLASS). VIII. The Influence of the Cluster Properties on H α Emitter Galaxies at 0.3 < z < 0.7

DOE PAGES

Vulcani, Benedetta; Treu, Tommaso; Nipoti, Carlo; ...

2017-03-10

In exploiting the data of the Grism Lens-Amplified Survey from Space (GLASS), we characterize the spatial distribution of star formation in 76 highly active star-forming galaxies in 10 clusters atmore » $$0.3\\lt z\\lt 0.7$$. All of these galaxies are likely restricted to first infall. We contrast the properties of field and cluster galaxies, in a companion paper, whereas here we correlate the properties of Hα emitters to a number of tracers of the cluster environment to investigate its role in driving galaxy transformations. Hα emitters are found in the clusters out to 0.5 virial radii, the maximum radius covered by GLASS. The peak of the Hα emission is offset with respect to the peak of the UV continuum. We also decompose these offsets into a radial and a tangential component. The radial component points away from the cluster center in 60% of the cases, with 95% confidence. The decompositions agree with cosmological simulations; that is, the Hα emission offset correlates with galaxy velocity and ram-pressure stripping signatures. Furthermore, trends between Hα emitter properties and surface mass density distributions and X-ray emissions emerge only for unrelaxed clusters. The lack of strong correlations with the global environment does not allow us to identify a unique environmental effect originating from the cluster center. In contrast, correlations between Hα morphology and local number density emerge. We conclude that local effects, uncorrelated to the cluster-centric radius, play a more important role in shaping galaxy properties.« less

The Grism Lens-Amplified Survey from Space (GLASS). VIII. The Influence of the Cluster Properties on H α Emitter Galaxies at 0.3 < z < 0.7

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vulcani, Benedetta; Treu, Tommaso; Nipoti, Carlo

In exploiting the data of the Grism Lens-Amplified Survey from Space (GLASS), we characterize the spatial distribution of star formation in 76 highly active star-forming galaxies in 10 clusters atmore » $$0.3\\lt z\\lt 0.7$$. All of these galaxies are likely restricted to first infall. We contrast the properties of field and cluster galaxies, in a companion paper, whereas here we correlate the properties of Hα emitters to a number of tracers of the cluster environment to investigate its role in driving galaxy transformations. Hα emitters are found in the clusters out to 0.5 virial radii, the maximum radius covered by GLASS. The peak of the Hα emission is offset with respect to the peak of the UV continuum. We also decompose these offsets into a radial and a tangential component. The radial component points away from the cluster center in 60% of the cases, with 95% confidence. The decompositions agree with cosmological simulations; that is, the Hα emission offset correlates with galaxy velocity and ram-pressure stripping signatures. Furthermore, trends between Hα emitter properties and surface mass density distributions and X-ray emissions emerge only for unrelaxed clusters. The lack of strong correlations with the global environment does not allow us to identify a unique environmental effect originating from the cluster center. In contrast, correlations between Hα morphology and local number density emerge. We conclude that local effects, uncorrelated to the cluster-centric radius, play a more important role in shaping galaxy properties.« less

Impact of line edge roughness on the performance of 14-nm FinFET: Device-circuit Co-design

NASA Astrophysics Data System (ADS)

Rathore, Rituraj Singh; Rana, Ashwani K.

2018-01-01

With the evolution of sub-20 nm FinFET technology, line edge roughness (LER) has been identified as a critical problem and may result in critical device parameter variation and performance limitation in the future VLSI circuit application. In the present work, an analytical model of fin-LER has been presented, which shows the impact of correlated and uncorrelated LER on FinFET structure. Further, the influence of correlated and uncorrelated fin- LER on all electrical performance parameters is thoroughly investigated using the three-dimensional (3-D) Technology Computer Aided Design (TCAD) simulations for 14-nm technology node. Moreover, the impact of all possible fin shapes on threshold voltage (VTH), drain induced barrier lowering (DIBL), on-current (ION), and off-current (IOFF) has been compared with the well calibrated rectangular FinFET structure. In addition, the influence of all possible fin geometries on the read stability of six-transistor (6-T) Static-Random-Access-Memory (SRAM) has been investigated. The study reveals that fin-LER plays a vital role as it directly governs the electrostatics of the FinFET structure. This has been found that there is a high degree of fluctuations in all performance parameters for uncorrelated fin-LER type FinFETs as compared to correlated fin-LER with respect to rectangular FinFET structure. This paper gives physical insight of FinFET design, especially in sub-20 nm technology nodes by concluding that the impact of LER on electrical parameters are minimum for correlated LER.

50 CFR 600.1204 - Shark finning; possession at sea and landing of shark fins.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Shark finning; possession at sea and... PROVISIONS Shark Finning § 600.1204 Shark finning; possession at sea and landing of shark fins. (a)(1) No...)(2), except that sharks may be dressed at sea. (c) No person aboard a U.S. or foreign fishing vessel...

Actuation of a robotic fish caudal fin for low reaction torque

NASA Astrophysics Data System (ADS)

Yun, Dongwon; Kim, Kyung-Soo; Kim, Soohyun; Kyung, Jinho; Lee, Sunghee

2011-07-01

In this paper, a novel caudal fin for actuating a robotic fish is presented. The proposed caudal fin waves in a vertical direction with a specific spatial shape, which is determined by a so-called shape factor. For a specific shape factor, a traveling wave with a vertical phase difference is formed on a caudal fin during fin motion. It will be shown by the analysis that the maximum reaction torque at the joint of a caudal fin varies depending on the shape factors. Compared with a conventional plate type caudal fin, the proposed fin with a shape factor of 2π can eliminate the reaction torque perfectly, while keeping the propulsion force unchanged. The benefits of the proposed fin will be demonstrated by experiments.

Quantification of local strain distributions in nanoscale strained SiGe FinFET structures

NASA Astrophysics Data System (ADS)

Mochizuki, Shogo; Murray, Conal E.; Madan, Anita; Pinto, Teresa; Wang, Yun-Yu; Li, Juntao; Weng, Weihao; Jagannathan, Hemanth; Imai, Yasuhiko; Kimura, Shigeru; Takeuchi, Shotaro; Sakai, Akira

2017-10-01

Strain within nanoscale strained SiGe FinFET structures has been investigated using a combination of X-ray diffraction and transmission electron microscopy-based nanobeam diffraction (NBD) techniques to reveal the evolution of the stress state within the FinFETs. Reciprocal space maps collected using high-resolution X-ray diffraction exhibited distinct features corresponding to the SiGe fin width, pitch, and lattice deformation and were analyzed to quantify the state of stress within the fins. Although the majority of the SiGe fin volume exhibited a uniaxial stress state due to elastic relaxation of the transverse in-plane stress, NBD measurements confirmed a small interaction region near the SOI interface that is mechanically constrained by the underlying substrate. We have quantitatively characterized the evolution of the fin stress state from biaxial to uniaxial as a function of fin aspect ratio and Ge fraction and confirmed that the fins obey elastic deformation based on a model that depends on the relative difference between the equilibrium Si and SiGe lattice constants and relative fraction of in-plane stress transverse to the SiGe fins. Spatially resolved, nanobeam X-ray diffraction measurements conducted near the SiGe fin edge indicate the presence of additional elastic relaxation from a uniaxial stress state to a fully relaxed state at the fin edge. Mapping of the lattice deformation within 500 nm of this fin edge by NBD revealed large gradients, particularly at the top corner of the fin. The values of the volume averaged lattice deformation obtained by nanoXRD and NBD are qualitatively consistent. Furthermore, the modulation of strain at the fin edge obtained by quantitative analysis of the nanoXRD results agrees with the lattice deformation profile obtained by NBD.

Differential induction of four msx homeobox genes during fin development and regeneration in zebrafish.

PubMed

Akimenko, M A; Johnson, S L; Westerfield, M; Ekker, M

1995-02-01

To study the genetic regulation of growth control and pattern formation during fin development and regeneration, we have analysed the expression of four homeobox genes, msxA, msxB, msxC and msxD in zebrafish fins. The median fin fold, which gives rise to the unpaired fins, expresses these four msx genes during development. Transcripts of the genes are also present in cells of the presumptive pectoral fin buds. The most distal cells, the apical ectodermal ridge of the paired fins and the cleft and flanking cells of the median fin fold express all these msx genes with the exception of msxC. Mesenchymal cells underlying the most distal cells express all four genes. Expression of the msx genes in the fin fold and fin buds is transient and, by 3 days after fertilization, msx expression in the median fin fold falls below levels detectable by in situ hybridization. Although the fins of adult zebrafish normally have levels of msx transcripts undetectable by in situ hybridization, expression of all four genes is strongly reinduced during regeneration of both paired and unpaired fins. Induction of msx gene expression in regenerating caudal fins occurs as early as 30 hours postamputation. As the blastema forms, the levels of expression increase and reach a maximum between the third and fifth days. Then, msx expression progressively declines and disappears by day 12 when the caudal fin has grown back to its normal size. In the regenerating fin, the blastema cells that develop at the tip of each fin ray express msxB and msxC. Cells of the overlying epithelium express msxA and msxD, but do not express msxB or msxC. Amputations at various levels along the proximodistal axis of the fin suggest that msxB expression depends upon the position of the blastema, with cells of the rapidly proliferating proximal blastema expressing higher levels than the cells of the less rapidly proliferating distal blastema. Expression of msxC and msxD is independent of the position of the blastema cell along this axis. Our results suggest distinct roles for each of the four msx genes during fin development and regeneration and differential regulation of their expression.

Integration of oceanographic data with fin whale calling presence in the Bering Sea

NASA Astrophysics Data System (ADS)

Dasarathy, S.; Berchok, C.; Stabeno, P. J.; Crance, J.

2016-02-01

Through the integration of environmental data with passive acoustic monitoring, it is possible to investigate whether fin whale (Balaenoptera physalus) presence is influenced by environmental factors. Fin whale calling activity and concurrent environmental variables were analyzed from May 2012 to September 2013. These data were collected from passive acoustic and oceanographic moorings located in the Bering Sea. Fin whale calling presence was strongly correlated with three of the eight parameters analyzed: ice concentration, chlorophyll (a proxy for primary production), and temperature. Fin whale calling was negatively correlated with ice concentration; as ice concentration increased, fin whale calling decreased. A strong positive correlation was observed between fin whale calling and chlorophyll. A large spike in chlorophyll concentration in July 2013 preceded fin whale calling at the northern location. Fin whale calling also increased concurrently with a mixing of the water column (evidenced in the temperature data) at a depth of 30 to 50m. Peaks in chlorophyll concentration occurred after the mixing of the water column, and followed an increase in fin whale calling. These data illustrate the relationship between fin whale presence and environmental variables in the Bering Sea. These correlations may be used to predict the impact of climate change on fin whale populations in the rapidly changing environment of the Bering Sea.

Influence of Alumina Addition to Aluminum Fins for Compact Heat Exchangers Produced by Cold Spray Additive Manufacturing

NASA Astrophysics Data System (ADS)

Farjam, Aslan; Cormier, Yannick; Dupuis, Philippe; Jodoin, Bertrand; Corbeil, Antoine

2015-10-01

In this work, aluminum and aluminum-alumina powder mixtures were used to produce pyramidal fin arrays on aluminum substrates using cold spray as an additive manufacturing process. Using aluminum-alumina mixtures instead of pure aluminum powder could be seen as a cost-effective measure, preventing nozzle clogging or the need to use expensive polymer nozzles that wear out rapidly during cold spray. The fin geometries that were produced were observed using a 3D digital microscope to determine the flow passages width and fins' geometric details. Heat transfer and pressure drop tests were carried out using different ranges of appropriate Reynolds numbers for the sought commercial application to compare each fin array and determine the effect of alumina content. It was found that the presence of alumina reduces the fins' performance when compared to pure aluminum fins but that they were still outperforming traditional fins. Numerical simulations were performed to model the fin arrays and were used to predict the pressure loss in the fin array and compare these results with experimental values. The numerical model opens up new avenues in predicting different applicable operating conditions and other possible fin shapes using the same fin composition, instead of performing costly and time-consuming experiments.

An Investigation at Low Speed of the Spin Instability of Mortar-Shell Tails

NASA Technical Reports Server (NTRS)

Bird, John D.; Lichtenstein, Jacob H.

1957-01-01

An investigation was made in the Langley stability tunnel to study the influence of number of fins, fin shrouding, and fin aspect ratio on the spin instability of mortar-shell tail surfaces. It was found that the 12-fin tails tested spun less rapidly throughout the angle-of-yaw range than did the 6-fin tails and that fin shrouding reduced the spin encountered by a large amount.

Fin degeneration of young-of-the-year Alosa pseudoharengus (Clupeidae) in southern Lake Michigan

USGS Publications Warehouse

Brown, Edward H.; Norden, Carroll R.

1970-01-01

Young-of-the-year alewives, Alosa pseudoharengus, with extremely shortened caudal fins were observed at four locations in southern Lake Michigan between 1964 and 1968. Some of the fins appeared stunted or underdeveloped, but microscopic examination revealed a deterioration of the fins and not an ontogenetic abnormality. Deterioration of the caudal fin was frequently accompanied by degeneration of the dorsal and anal fins. Degenerate fins were not found on other species nor on older alewives, with the exception of one known yearling alewife at Waukegan and possibly a few of the larger fish at Milwaukee.

Effect of morphological fin curl on the swimming performance and station-holding ability of juvenile shovelnose sturgeon

USGS Publications Warehouse

Deslauriers, David; Johnston, Ryan; Chipps, Steven R.

2016-01-01

We assessed the effect of fin-curl on the swimming and station-holding ability of juvenile shovelnose sturgeon Scaphirhynchus platorynchus (mean fork length = 17 cm; mean weight = 16 g; n = 21) using a critical swimming speed test performed in a small swim chamber (90 L) at 20°C. We quantified fin-curl severity using the pectoral fin index. Results showed a positive relationship between pectoral fin index and critical swimming speed indicative of reduced swimming performance displayed by fish afflicted with a pectoral fin index < 8%. Fin-curl severity, however, did not affect the station-holding ability of individual fish. Rather, fish affected with severe fin-curl were likely unable to use their pectoral fins to position their body adequately in the water column, which led to the early onset of fatigue. Results generated from this study should serve as an important consideration for future stocking practices.

Highly flexible SRAM cells based on novel tri-independent-gate FinFET

NASA Astrophysics Data System (ADS)

Liu, Chengsheng; Zheng, Fanglin; Sun, Yabin; Li, Xiaojin; Shi, Yanling

2017-10-01

In this paper, a novel tri-independent-gate (TIG) FinFET is proposed for highly flexible SRAM cells design. To mitigate the read-write conflict, two kinds of SRAM cells based on TIG FinFETs are designed, and high tradeoff are obtained between read stability and speed. Both cells can offer multi read operations for frequency requirement with single voltage supply. In the first TIG FinFET SRAM cell, the strength of single-fin access transistor (TIG FinFET) can be flexibly adjusted by selecting five different modes to meet the needs of dynamic frequency design. Compared to the previous double-independent-gate (DIG) FinFET SRAM cell, 12.16% shorter read delay can be achieved with only 1.62% read stability decrement. As for the second TIG FinFET SRAM cell, pass-gate feedback technology is applied and double-fin TIG FinFETs are used as access transistors to solve the severe write-ability degradation. Three modes exist to flexibly adjust read speed and stability, and 68.2% larger write margin and 51.7% shorter write delay are achieved at only the expense of 26.2% increase in leakage power, with the same layout area as conventional FinFET SRAM cell.

Effect of Fin Porosity on Wake Geometry for Flapping Fins at Intermediate Reynolds Number

NASA Astrophysics Data System (ADS)

Chen, J.; Xia, B.; Krueger, P. S.

2017-11-01

Low aspect ratio flapping fins generate interesting 3-dimensional flow structures as has been observed, for example, in studies of fish swimming. As the Reynolds number is reduced, the exact geometry of the fin is less important and even certain amounts of porosity might be allowed without significantly affecting propulsive performance. These effects are investigated experimentally using flapping rectangular fins of aspect ratio 2 at Reynolds numbers in the range 100 - 1000. The experiments were conducted using a water tunnel to supply the free stream flow and the fin flapping parameters were set to provide a Strouhal number (based on amplitude of the fin tip motion) in the range 0.15 - 0.35. Phase-averaged measurements were made of the 3-dimensional, volumetric flow field, allowing visualization of the typical shed vortex structure behind the fin and calculation of time averaged thrust and propulsive efficiency. Results comparing the flow structure in the fin wake and the resulting propulsive performance will be presented for several fins with different planform porosities where the porosities are set using arrays of holes in the fins. This material is based on the work supported by the National Science Foundation under Grant No. 1510707.

Grid Fin Stabilization of the Orion Launch Abort Vehicle

NASA Technical Reports Server (NTRS)

Pruzan, Daniel A.; Mendenhall, Michael R.; Rose, William C.; Schuster, David M.

2011-01-01

Wind tunnel tests were conducted by Nielsen Engineering & Research (NEAR) and Rose Engineering & Research (REAR) in conjunction with the NASA Engineering & Safety Center (NESC) on a 6%-scale model of the Orion launch abort vehicle (LAV) configured with four grid fins mounted near the base of the vehicle. The objectives of these tests were to 1) quantify LAV stability augmentation provided by the grid fins from subsonic through supersonic Mach numbers, 2) assess the benefits of swept grid fins versus unswept grid fins on the LAV, 3) determine the effects of the LAV abort motors on grid fin aerodynamics, and 4) generate an aerodynamic database for use in the future application of grid fins to small length-to-diameter ratio vehicles similar to the LAV. The tests were conducted in NASA Ames Research Center's 11x11-foot transonic wind tunnel from Mach 0.5 through Mach 1.3 and in their 9x7-foot supersonic wind tunnel from Mach 1.6 through Mach 2.5. Force- and moment-coefficient data were collected for the complete vehicle and for each individual grid fin as a function of angle of attack and sideslip angle. Tests were conducted with both swept and unswept grid fins with the simulated abort motors (cold jets) off and on. The swept grid fins were designed with a 22.5deg aft sweep angle for both the frame and the internal lattice so that the frontal projection of the swept fins was the same as for the unswept fins. Data from these tests indicate that both unswept and swept grid fins provide significant improvements in pitch stability as compared to the baseline vehicle over the Mach number range investigated. The swept fins typically provide improved stability as compared to the unswept fins, but the performance gap diminished as Mach number was increased. The aerodynamic performance of the fins was not observed to degrade when the abort motors were turned on. Results from these tests indicate that grid fins can be a robust solution for stabilizing the Orion LAV over a wide range of operating conditions.

Passively cooled direct drive wind turbine

DOEpatents

Costin, Daniel P [Chelsea, VT

2008-03-18

A wind turbine is provided that passively cools an electrical generator. The wind turbine includes a plurality of fins arranged peripherally around a generator house. Each of the fins being oriented at an angle greater than zero degrees to allow parallel flow of air over the fin. The fin is further tapered to allow a constant portion of the fin to extend beyond the air stream boundary layer. Turbulence initiators on the nose cone further enhance heat transfer at the fins.

Parametric Fin-Body and Fin-Plate Database for a Series of 12 Missile Fins

NASA Technical Reports Server (NTRS)

Allen, Jerry M.

2001-01-01

A cooperative experimental investigation has been performed to obtain a systematic fin-body and fin-plate database for a series of 12 missile fins. These data are intended to complement and extend the information contained in the Triservice missile project and to provide a systematic set of experimental data from which fin-body interference factors can be derived. Data were obtained with the fins mounted on both an axisymmetric body and on a flat plate that was used to simulate fin-alone measurements. The experiments were conducted at Mach numbers from 0.60 to 3.95; fin deflection angles of 0 deg, 10 deg, and -10 deg; and angles of attack up to 30 deg on the body and up to 95 deg on the flat plate. The data were obtained from three-component balances attached to the fins and a six-component balance located in the axisymmetric body. The data obtained in this project are documented in tabular form in this report. In addition, selected data are presented in graphical form to illustrate the effects of the test variables. These variables are configuration angle of attack; Mach number; and fin parameters of deflection angle, planform size, taper ratio, and aspect ratio. A very limited comparison with the Triservice missile data is made to illustrate the consistency between the data from these two projects.

Mechanosensation is evolutionarily tuned to locomotor mechanics

PubMed Central

Aiello, Brett R.; Westneat, Mark W.; Hale, Melina E.

2017-01-01

The biomechanics of animal limbs has evolved to meet the functional demands for movement associated with different behaviors and environments. Effective movement relies not only on limb mechanics but also on appropriate mechanosensory feedback. By comparing sensory ability and mechanics within a phylogenetic framework, we show that peripheral mechanosensation has evolved with limb biomechanics, evolutionarily tuning the neuromechanical system to its functional demands. We examined sensory physiology and mechanics of the pectoral fins, forelimb homologs, in the fish family Labridae. Labrid fishes exhibit extraordinary morphological and behavioral diversity and use pectoral fin-based propulsion with fins ranging in shape from high aspect ratio (AR) wing-like fins to low AR paddle-like fins. Phylogenetic character analysis demonstrates that high AR fins evolved independently multiple times in this group. Four pairs of species were examined; each included a plesiomorphic low AR and a high AR species. Within each species pair, the high AR species demonstrated significantly stiffer fin rays in comparison with the low AR species. Afferent sensory nerve activity was recorded during fin ray bending. In all cases, afferents of stiffer fins were more sensitive at lower displacement amplitudes, demonstrating mechanosensory tuning to fin mechanics and a consistent pattern of correlated evolution. We suggest that these data provide a clear example of parallel evolution in a complex neuromechanical system, with a strong link between multiple phenotypic characters: pectoral fin shape, swimming behavior, fin ray stiffness, and mechanosensory sensitivity. PMID:28396411

14 CFR 23.445 - Outboard fins or winglets.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Outboard fins or winglets. 23.445 Section... § 23.445 Outboard fins or winglets. (a) If outboard fins or winglets are included on the horizontal... with loads induced by the fins or winglets and moments or forces exerted on the horizontal surfaces or...

14 CFR 23.445 - Outboard fins or winglets.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Outboard fins or winglets. 23.445 Section... § 23.445 Outboard fins or winglets. (a) If outboard fins or winglets are included on the horizontal... with loads induced by the fins or winglets and moments or forces exerted on the horizontal surfaces or...

14 CFR 23.445 - Outboard fins or winglets.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Outboard fins or winglets. 23.445 Section... § 23.445 Outboard fins or winglets. (a) If outboard fins or winglets are included on the horizontal... with loads induced by the fins or winglets and moments or forces exerted on the horizontal surfaces or...

Numerical analysis on interactions between fluid flow and structure deformation in plate-fin heat exchanger by Galerkin method

NASA Astrophysics Data System (ADS)

Liu, Jing-cheng; Wei, Xiu-ting; Zhou, Zhi-yong; Wei, Zhen-wen

2018-03-01

The fluid-structure interaction performance of plate-fin heat exchanger (PFHE) with serrated fins in large scale air-separation equipment was investigated in this paper. The stress and deformation of fins were analyzed, besides, the interaction equations were deduced by Galerkin method. The governing equations of fluid flow and heat transfer in PFHE were deduced by finite volume method (FVM). The distribution of strain and stress were calculated in large scale air separation equipment and the coupling situation of serrated fins under laminar situation was analyzed. The results indicated that the interactions between fins and fluid flow in the exchanger have significant impacts on heat transfer enhancement, meanwhile, the strain and stress of fins includes dynamic pressure of the sealing head and flow impact with the increase of flow velocity. The impacts are especially significant at the conjunction of two fins because of the non-alignment fins. It can be concluded that the soldering process and channel width led to structure deformation of fins in the exchanger, and degraded heat transfer efficiency.

Investigation of thermal effects on FinFETs in the quasi-ballistic regime

NASA Astrophysics Data System (ADS)

Yin, Longxiang; Shen, Lei; Di, Shaoyan; Du, Gang; Liu, Xiaoyan

2018-04-01

In this work, the thermal effects of FinFETs in the quasi-ballistic regime are investigated using the Monte Carlo method. Bulk Si nFinFETs with the same fin structure and two different gate lengths L g = 20 and 80 nm are investigated and compared to evaluate the thermal effects on the performance of FinFETs in the quasi-ballistic regime. The on current of the 20 nm FinFET with V gs = 0.7 V does not decrease with increasing lattice temperature (T L) at a high V ds. The electrostatic properties in the 20 nm FinFET are more affected by T L than those in the 80 nm FinFET. However, the electron transport in the 20 nm FinFET is less affected by T L than that in the 80 nm FinFET. The electrostatic properties being more sensitive and the electron transport being less sensitive to thermal effects in the quasi-ballistic regime than in the diffusive regime should be considered for effective device modeling and design.

Enhancement of the forced convective heat transfer on mini pin fin heat sinks with micro spiral fins

NASA Astrophysics Data System (ADS)

Khonsue, Osot

2018-02-01

This research is an experimental study on the characteristics of heat transfer and pressure drop in mini heat sinks using air as the working fluid. The experiments were performed under a constant heat flux ranging from 9.132-13.698 kW/m2 and the air Reynolds number range 322-1982. Three different types of mini heat sinks were rectangle pin fins, cylindrical pin fins, and spiral pin fins with 36x28x9 mm and 5 mm fins high. There were 63 fins altogether and all were made of aluminum. The results showed that the characteristics of the temperature of heat sink of spiral pin fins was the least. Meanwhile the average heat transfer coefficient and Nusselt number of spiral pin fins were the most . Regarding the pressure drop, the rectangular pin fins was the least. The results of this study can be used to guide the design and development of electronic devices cooling system with forced convective heat transfer for higher performance in the future.

Forced air heat sink apparatus

NASA Technical Reports Server (NTRS)

Rippel, Wally E. (Inventor)

1989-01-01

A high efficiency forced air heat sink assembly employs a split feed transverse flow configuration to minimize the length of the air flow path through at least two separated fin structures. Different embodiments use different fin structure material configurations including honeycomb, corrugated and serpentine. Each such embodiment uses a thermally conductive plate having opposed exterior surfaces; one for receiving a component to be cooled and one for receiving the fin structures. The serpentine structured fin embodiment employs a plurality of fin supports extending from the plate and forming a plurality of channels for receiving the fin structures. A high thermal conductivity bondant, such as metal-filled epoxy, may be used to bond the fin structures to either the plate or the fin supports. Dip brazing and soldering may also be employed depending upon the materials selected.

FIN219/JAR1 and cryptochrome1 antagonize each other to modulate photomorphogenesis under blue light in Arabidopsis

PubMed Central

2018-01-01

Plant development is affected by the integration of light and phytohormones, including jasmonates (JAs). To address the molecular mechanisms of possible interactions between blue light and JA signaling in Arabidopsis thaliana, we used molecular and transgenic approaches to understand the regulatory relationships between FAR-RED INSENSITIVE 219 (FIN219)/JASMONATE RESISTANT1 (JAR1) and the blue-light photoreceptor cryptochrome1 (CRY1). FIN219 overexpression in the wild type resulted in a short-hypocotyl phenotype under blue light. However, FIN219 overexpression in cry1, cry2 and cry1cry2 double mutant backgrounds resulted in phenotypes similar to their respective mutant backgrounds, which suggests that FIN219 function may require blue light photoreceptors. Intriguingly, FIN219 overexpression in transgenic plants harboring ectopic expression of the C terminus of CRY1 (GUS-CCT1), which exhibits a hypersensitive short-hypocotyl phenotype in all light conditions including darkness, led to a rescued phenotype under all light conditions except red light. Further expression studies showed mutual suppression between FIN219 and CRY1 under blue light. Strikingly, FIN219 overexpression in GUS-CCT1 transgenic lines (FIN219-OE/GUS-CCT1) abolished GUS-CCT1 fusion protein under blue light, whereas GUS-CCT1 fusion protein was stable in the fin219-2 mutant background (fin219-2/GUS-CCT1). Moreover, FIN219 strongly interacted with COP1 under blue light, and methyl JA (MeJA) treatment enhanced the interaction between FIN219 and GUS-CCT1 under blue light. Furthermore, FIN219 level affected GUS-CCT1 seedling responses such as anthocyanin accumulation and bacterial resistance under various light conditions and MeJA treatment. Thus, FIN219/JAR1 and CRY1 antagonize each other to modulate photomorphogenic development of seedlings and stress responses in Arabidopsis. PMID:29561841

FIN219/JAR1 and cryptochrome1 antagonize each other to modulate photomorphogenesis under blue light in Arabidopsis.

PubMed

Chen, Huai-Ju; Fu, Tsu-Yu; Yang, Shao-Li; Hsieh, Hsu-Liang

2018-03-01

Plant development is affected by the integration of light and phytohormones, including jasmonates (JAs). To address the molecular mechanisms of possible interactions between blue light and JA signaling in Arabidopsis thaliana, we used molecular and transgenic approaches to understand the regulatory relationships between FAR-RED INSENSITIVE 219 (FIN219)/JASMONATE RESISTANT1 (JAR1) and the blue-light photoreceptor cryptochrome1 (CRY1). FIN219 overexpression in the wild type resulted in a short-hypocotyl phenotype under blue light. However, FIN219 overexpression in cry1, cry2 and cry1cry2 double mutant backgrounds resulted in phenotypes similar to their respective mutant backgrounds, which suggests that FIN219 function may require blue light photoreceptors. Intriguingly, FIN219 overexpression in transgenic plants harboring ectopic expression of the C terminus of CRY1 (GUS-CCT1), which exhibits a hypersensitive short-hypocotyl phenotype in all light conditions including darkness, led to a rescued phenotype under all light conditions except red light. Further expression studies showed mutual suppression between FIN219 and CRY1 under blue light. Strikingly, FIN219 overexpression in GUS-CCT1 transgenic lines (FIN219-OE/GUS-CCT1) abolished GUS-CCT1 fusion protein under blue light, whereas GUS-CCT1 fusion protein was stable in the fin219-2 mutant background (fin219-2/GUS-CCT1). Moreover, FIN219 strongly interacted with COP1 under blue light, and methyl JA (MeJA) treatment enhanced the interaction between FIN219 and GUS-CCT1 under blue light. Furthermore, FIN219 level affected GUS-CCT1 seedling responses such as anthocyanin accumulation and bacterial resistance under various light conditions and MeJA treatment. Thus, FIN219/JAR1 and CRY1 antagonize each other to modulate photomorphogenic development of seedlings and stress responses in Arabidopsis.

Transonic static and dynamic stability characteristics of a finned projectile configuration

NASA Technical Reports Server (NTRS)

Boyden, R. P.; Brooks, C. W., Jr.; Davenport, E. E.

1978-01-01

Static and dynamic stability tests were made of a finned projectile configuration with the aft-mounted fins arranged in a cruciform pattern. The tests were made at free stream Mach numbers of 0.7, 0.9, 1.1, and 1.2 in the Langley 8-foot transonic pressure tunnel. Some of the parameters measured during the tests were lift, drag, pitching moment, pitch damping, and roll damping. Configurations tested included the body with undeflected fins, the body with various fin deflections for control, and the body with fins removed. Theoretical estimates of the stability derivatives were made for the fins on configuration.

Flow structure of natural dehumidification over a horizontal finned-tube

NASA Astrophysics Data System (ADS)

Hirbodi, Kamran; Yaghoubi, Mahmood

2016-08-01

In the present study, structure of water drops formation, growth, coalescence and departure over a horizontal finned-tube during natural dehumidification is investigated experimentally. Starting time of repelling the drops as well as heat transfer rate and the rate of dripping condensates in quasi-steady-state conditions are presented. Furthermore, cold airflow pattern around the horizontal finned-tube is visualized by using smoke generation scheme during natural dehumidification process. The finned-tube has a length of 300 mm, and inner and outer fin diameters, fin thickness and fin spacing are 25.4, 56, 0.4 and 2 mm, respectively. The tests are conducted in an insulated control room with dimensions of 5.8 m × 3 m × 4 m. Ambient air temperature, relative humidity and fin base temperature are selected from 25 to 35 °C, from 40 to 70 % and from 4 to 8 °C, respectively. Observations show that natural condensation from humid air over the test case is completely dropwise. Droplets only form on the edge of the fin and lateral fin surfaces remain almost dry. Dehumidification process over the tested finned-tube is divided into four stages; nucleation, formation, growth and departure of drops. It is also observed that the condensate inundation leaves the tube bottom in the form of droplets. Smoke visualization depicts that humid airflows downward around the cold finned-tube surface without noticeable turbulence and separation in the initial stages of dehumidification process. But the airflow has some disturbances in the intermediate stage and especially during drop departure on the edge of the fins.

Velocity Deficits in the Wake of Model Lemon Shark Dorsal Fins Measured with Particle Image Velocimetry

NASA Astrophysics Data System (ADS)

Terry, K. N.; Turner, V.; Hackett, E.

2017-12-01

Aquatic animals' morphology provides inspiration for human technological developments, as their bodies have evolved and become adapted for efficient swimming. Lemon sharks exhibit a uniquely large second dorsal fin that is nearly the same size as the first fin, the hydrodynamic role of which is unknown. This experimental study looks at the drag forces on a scale model of the Lemon shark's unique two-fin configuration in comparison to drag forces on a more typical one-fin configuration. The experiments were performed in a recirculating water flume, where the wakes behind the scale models are measured using particle image velocimetry. The experiments are performed at three different flow speeds for both fin configurations. The measured instantaneous 2D distributions of the streamwise and wall-normal velocity components are ensemble averaged to generate streamwise velocity vertical profiles. In addition, velocity deficit profiles are computed from the difference between these mean streamwise velocity profiles and the free stream velocity, which is computed based on measured flow rates during the experiments. Results show that the mean velocities behind the fin and near the fin tip are smallest and increase as the streamwise distance from the fin tip increases. The magnitude of velocity deficits increases with increasing flow speed for both fin configurations, but at all flow speeds, the two-fin configurations generate larger velocity deficits than the one-fin configurations. Because the velocity deficit is directly proportional to the drag force, these results suggest that the two-fin configuration produces more drag.

Heat Transfer Measurements of Internally Finned Rotating Heat Pipes.

DTIC Science & Technology

1983-12-01

42 C. RESULTS OF STRAIGHT 22 FIN CONDENSER o . o . 51 D. RESULTS OF HELICAL 14 AND 16 FIN CONDENSER o 51 E. RESULTS OF HELICAL 36 FIN...88 C.6 RESULTS OF STRAIGHT 22 FIN CONDENSER AT 2800 RPM . . . . . . . . . . . . . . . . . . . . 89 C.7 RESULTS OF HELICAL 16 FIN CONDENSER ...AT 700 RPM . 90 C.8 RESULTS OF HELICAL 16 PIN CONDENSER AT 1600 RPM . 91 C.9 RESULTS OF HELICAL 16 PIN CONDENSER AT 2800 RPM . 92 C. 10 RESULTS OF

Fully-Implicit Navier-Stokes (FIN-S)

NASA Technical Reports Server (NTRS)

Kirk, Benjamin S.

2010-01-01

FIN-S is a SUPG finite element code for flow problems under active development at NASA Lyndon B. Johnson Space Center and within PECOS: a) The code is built on top of the libMesh parallel, adaptive finite element library. b) The initial implementation of the code targeted supersonic/hypersonic laminar calorically perfect gas flows & conjugate heat transfer. c) Initial extension to thermochemical nonequilibrium about 9 months ago. d) The technologies in FIN-S have been enhanced through a strongly collaborative research effort with Sandia National Labs.

Efficient level set methods for constructing wavefronts in three spatial dimensions

NASA Astrophysics Data System (ADS)

Cheng, Li-Tien

2007-10-01

Wavefront construction in geometrical optics has long faced the twin difficulties of dealing with multi-valued forms and resolution of wavefront surfaces. A recent change in viewpoint, however, has demonstrated that working in phase space on bicharacteristic strips using eulerian methods can bypass both difficulties. The level set method for interface dynamics makes a suitable choice for the eulerian method. Unfortunately, in three-dimensional space, the setting of interest for most practical applications, the advantages of this method are largely offset by a new problem: the high dimension of phase space. In this work, we present new types of level set algorithms that remove this obstacle and demonstrate their abilities to accurately construct wavefronts under high resolution. These results propel the level set method forward significantly as a competitive approach in geometrical optics under realistic conditions.

Correlated evolution of body and fin morphology in the cichlid fishes.

PubMed

Feilich, Kara L

2016-10-01

Body and fin shapes are chief determinants of swimming performance in fishes. Different configurations of body and fin shapes can suit different locomotor specializations. The success of any configuration is dependent upon the hydrodynamic interactions between body and fins. Despite the importance of body-fin interactions for swimming, there are few data indicating whether body and fin configurations evolve in concert, or whether these structures vary independently. The cichlid fishes are a diverse family whose well-studied phylogenetic relationships make them ideal for the study of macroevolution of ecomorphology. This study measured body, and caudal and median fin morphology from radiographs of 131 cichlid genera, using morphometrics and phylogenetic comparative methods to determine whether these traits exhibit correlated evolution. Partial least squares canonical analysis revealed that body, caudal fin, dorsal fin, and anal fin shapes all exhibited strong correlated evolution consistent with locomotor ecomorphology. Major patterns included the evolution of deep body profiles with long fins, suggestive of maneuvering specialization; and the evolution of narrow, elongate caudal peduncles with concave tails, a combination that characterizes economical cruisers. These results demonstrate that body shape evolution does not occur independently of other traits, but among a suite of other morphological changes that augment locomotor specialization. © 2016 The Author(s). Evolution © 2016 The Society for the Study of Evolution.

Undulating fins produce off-axis thrust and flow structures.

PubMed

Neveln, Izaak D; Bale, Rahul; Bhalla, Amneet Pal Singh; Curet, Oscar M; Patankar, Neelesh A; MacIver, Malcolm A

2014-01-15

While wake structures of many forms of swimming and flying are well characterized, the wake generated by a freely swimming undulating fin has not yet been analyzed. These elongated fins allow fish to achieve enhanced agility exemplified by the forward, backward and vertical swimming capabilities of knifefish, and also have potential applications in the design of more maneuverable underwater vehicles. We present the flow structure of an undulating robotic fin model using particle image velocimetry to measure fluid velocity fields in the wake. We supplement the experimental robotic work with high-fidelity computational fluid dynamics, simulating the hydrodynamics of both a virtual fish, whose fin kinematics and fin plus body morphology are measured from a freely swimming knifefish, and a virtual rendering of our robot. Our results indicate that a series of linked vortex tubes is shed off the long edge of the fin as the undulatory wave travels lengthwise along the fin. A jet at an oblique angle to the fin is associated with the successive vortex tubes, propelling the fish forward. The vortex structure bears similarity to the linked vortex ring structure trailing the oscillating caudal fin of a carangiform swimmer, though the vortex rings are distorted because of the undulatory kinematics of the elongated fin.

Establishment of a biomimetic device based on tri-layer polymer actuators--propulsion fins.

PubMed

Alici, Gursel; Spinks, Geoffrey; Huynh, Nam N; Sarmadi, Laleh; Minato, Rick

2007-06-01

We propose to use bending type tri-layer polymer actuators as propulsion fins for a biomimetic device consisting of a rigid body, like a box fish having a carapace, and paired fins running through the rigid body, like a fish having pectoral fins. The fins or polymer bending actuators can be considered as individually controlled flexible membranes. Each fin is activated with sinusoidal inputs such that there is a phase lag between the movements of successive fins to create enough thrust force for propulsion. Eight fins with 0.125 aspect ratio have been used along both sides of the rigid body to move the device in the direction perpendicular to the longitudinal axis of the body. The designed device with the paired fins was successfully tested, moving in an organic solution consisting of solvent, propylene carbonate (PC), and electrolyte. The design procedure outlined in this study is offered as a guide to making functional devices based on polymer actuators and sensors.

Ge-cap quantum-well bulk FinFET for 5 nm node CMOS integration

NASA Astrophysics Data System (ADS)

Dwi Kurniawan, Erry; Peng, Kang-Hui; Yang, Shang-Yi; Yang, Yi-Yun; Thirunavukkarasu, Vasanthan; Lin, Yu-Hsien; Wu, Yung-Chun

2018-04-01

We propose the use of Ge-cap quantum-well (QW) bulk FinFET for 5 nm CMOS integration, which is a Si channel wrapped with Ge around three sides of the fin channel. The simulation results show that the Ge-cap FinFET structure demonstrates better performance than pure Si, pure Ge, and Si-cap FinFET structures. By optimizing Si fin width and Ge-cap thickness, the on-state current of nFET and pFET can also be symmetric without changing the total fin width (F Wp = F Wn). The electrons in Ge-cap nFinFET concentrate in the Si channel because of QWs formed in the lowest conduction band of the Ge and Si heterostructure, while the holes in Ge-cap pFinFET prefer to stay in Ge surfaces owing to QWs formed in the Ge valence band. The physics studies of this device have made the design rules relevant for the application of the CMOS inverter and static random access memory (SRAM) application technology.

Effects of ultra-thin Si-fin body widths upon SOI PMOS FinFETs

NASA Astrophysics Data System (ADS)

Liaw, Yue-Gie; Chen, Chii-Wen; Liao, Wen-Shiang; Wang, Mu-Chun; Zou, Xuecheng

2018-05-01

Nano-node tri-gate FinFET devices have been developed after integrating a 14 Å nitrided gate oxide upon the silicon-on-insulator (SOI) wafers established on an advanced CMOS logic platform. These vertical double gate (FinFET) devices with ultra-thin silicon fin (Si-fin) widths ranging from 27 nm to 17 nm and gate length down to 30 nm have been successfully developed with a 193 nm scanner lithography tool. Combining the cobalt fully silicidation and the CESL strain technology beneficial for PMOS FinFETs was incorporated into this work. Detailed analyses of Id-Vg characteristics, threshold voltage (Vt), and drain-induced barrier lowering (DIBL) illustrate that the thinnest 17 nm Si-fin width FinFET exhibits the best gate controllability due to its better suppression of short channel effect (SCE). However, higher source/drain resistance (RSD), channel mobility degradation due to dry etch steps, or “current crowding effect” will slightly limit its transconductance (Gm) and drive current.

Morphogenesis and evolution of vertebrate appendicular muscle

PubMed Central

HAINES, LYNN; CURRIE, PETER D.

2001-01-01

Two different modes are utilised by vertebrate species to generate the appendicular muscle present within fins and limbs. Primitive Chondricthyan or cartilaginous fishes use a primitive mode of muscle formation to generate the muscle of the fins. Direct epithelial myotomal extensions invade the fin and generate the fin muscles while remaining in contact with the myotome. Embryos of amniotes such as chick and mouse use a similar mechanism to that deployed in the bony teleost species, zebrafish. Migratory mesenchymal myoblasts delaminate from fin/limb level somites, migrate to the fin/limb field and differentiate entirely within the context of the fin/limb bud. Migratory fin and limb myoblasts express identical genes suggesting that they possess both morphogenetic and molecular identity. We conclude that the mechanisms controlling tetrapod limb muscle formation arose prior to the Sarcopterygian or tetrapod radiation. PMID:11523824

Mach 6 experimental and theoretical stability and performance of a cruciform missile at angles of attack up to 65 degrees

NASA Technical Reports Server (NTRS)

Hartman, Edward R.; Johnston, Patrick J.

1987-01-01

An experimental and theoretical investigation of the longitudinal and lateral-directional stability and control of an axisymmetric cruciform-finned missile has been conducted at Mach 6. The angle-of-attack range extended from 20 to 65 deg to encompass maximum lift. Longitudinal stability, performance, and trim could be accurately predicted with the fins at a fin roll angle of 0 deg but not when the fins were at a fin roll angle of 45 deg. At this roll angle, windward fin choking occurred at angles of attack above 50 deg and reduced the effectiveness of the fins and caused pitch-up.

Genetically distinct colour morphs of European perch Perca fluviatilis in Lake Constance differ in susceptibility to macroparasites.

PubMed

Roch, S; Behrmann-Godel, J; Brinker, A

2015-01-21

The unusual yellow-finned morph of European perch Perca fluviatilis found in Lake Constance suffers more severely from macroparasite infections, including the tapeworm Triaenophorus nodulosus and the gill worm Ancyrocephalus percae, than conspecifics elsewhere. Microsatellite analysis of yellow-finned P. fluviatilis and red-finned variant recently discovered in Lake Constance revealed significant genetic differentiation. Red-finned P. fluviatilis and fish with mixed fin colour, suggested backcrosses between red and yellow-finned colour morphs, exhibit better resilience to parasite infection, suggesting that the inability of the yellow-finned morph to reject macroparasites may have a genetic basis. © 2015 The Fisheries Society of the British Isles.

Musculoskeletal anatomy of the pelvic fin of Polypterus: implications for phylogenetic distribution and homology of pre- and postaxial pelvic appendicular muscles.

PubMed

Molnar, Julia L; Johnston, Peter S; Esteve-Altava, Borja; Diogo, Rui

2017-04-01

As a member of the most basal clade of extant ray-finned fishes (actinopterygians) and of one of the most basal clades of osteichthyans (bony fishes + tetrapods), Polypterus can provide insights into the ancestral anatomy of both ray-finned and lobe-finned fishes, including those that gave rise to tetrapods. The pectoral fin of Polypterus has been well described but, surprisingly, neither the bones nor the muscles of the pelvic fin are well known. We stained and dissected the pelvic fin of Polypterus senegalus and Polypterus delhezi to offer a detailed description of its musculoskeletal anatomy. In addition to the previously described adductor and abductor muscles, we found preaxial and postaxial muscles similar to those in the pectoral fin of members of this genus. The presence of pre- and postaxial muscles in both the pectoral and pelvic fins of Polypterus, combined with recent descriptions of similar muscles in the lobe-finned fishes Latimeria and Neoceratodus, suggests that they were present in the most recent common ancestor of bony fishes. These results have crucial implications for the evolution of appendicular muscles in both fish and tetrapods. © 2016 Anatomical Society.

Curvature-induced stiffening of a fish fin.

PubMed

Nguyen, Khoi; Yu, Ning; Bandi, Mahesh M; Venkadesan, Madhusudhan; Mandre, Shreyas

2017-05-01

How fish modulate their fin stiffness during locomotive manoeuvres remains unknown. We show that changing the fin's curvature modulates its stiffness. Modelling the fin as bendable bony rays held together by a membrane, we deduce that fin curvature is manifested as a misalignment of the principal bending axes between neighbouring rays. An external force causes neighbouring rays to bend and splay apart, and thus stretches the membrane. This coupling between bending the rays and stretching the membrane underlies the increase in stiffness. Using three-dimensional reconstruction of a mackerel ( Scomber japonicus ) pectoral fin for illustration, we calculate the range of stiffnesses this fin is expected to span by changing curvature. The three-dimensional reconstruction shows that, even in its geometrically flat state, a functional curvature is embedded within the fin microstructure owing to the morphology of individual rays. As the ability of a propulsive surface to transmit force to the surrounding fluid is limited by its stiffness, the fin curvature controls the coupling between the fish and its surrounding fluid. Thereby, our results provide mechanical underpinnings and morphological predictions for the hypothesis that the spanned range of fin stiffnesses correlates with the behaviour and the ecological niche of the fish. © 2017 The Author(s).

Curvature-induced stiffening of a fish fin

PubMed Central

2017-01-01

How fish modulate their fin stiffness during locomotive manoeuvres remains unknown. We show that changing the fin's curvature modulates its stiffness. Modelling the fin as bendable bony rays held together by a membrane, we deduce that fin curvature is manifested as a misalignment of the principal bending axes between neighbouring rays. An external force causes neighbouring rays to bend and splay apart, and thus stretches the membrane. This coupling between bending the rays and stretching the membrane underlies the increase in stiffness. Using three-dimensional reconstruction of a mackerel (Scomber japonicus) pectoral fin for illustration, we calculate the range of stiffnesses this fin is expected to span by changing curvature. The three-dimensional reconstruction shows that, even in its geometrically flat state, a functional curvature is embedded within the fin microstructure owing to the morphology of individual rays. As the ability of a propulsive surface to transmit force to the surrounding fluid is limited by its stiffness, the fin curvature controls the coupling between the fish and its surrounding fluid. Thereby, our results provide mechanical underpinnings and morphological predictions for the hypothesis that the spanned range of fin stiffnesses correlates with the behaviour and the ecological niche of the fish. PMID:28566508

Testing Momentum Enhancement of Ribbon Fin Based Propulsion Using a Robotic Model With an Adjustable Body

NASA Astrophysics Data System (ADS)

English, Ian; Curet, Oscar

2016-11-01

Lighthill and Blake's 1990 momentum enhancement theory suggests there is a multiplicative propulsive effect linked to the ratio of body and fin heights in Gymnotiform and Balistiform swimmers, which propel themselves using multi-rayed undulating fins while keeping their bodies mostly rigid. Proof of such a momentum enhancement could have a profound effect on unmanned underwater vehicle design and shed light on the evolutionary advantage to body-fin ratios found in nature, shown as optimal for momentum enhancement in Lighthill and Blake's theory. A robotic ribbon fin with twelve independent fin rays, elastic fin membrane, and a body of adjustable height was developed specifically to experimentally test momentum enhancement. Thrust tests for various body heights were conducted in a recirculating flow tank at different flow speeds and fin flapping frequencies. When comparing thrust at different body heights, flow speeds, and frequencies to a 'no-body' thrust test case at each frequency and flow speed, data indicate there is no momentum enhancement factor due to the presence of a body on top of an undulating fin. This suggests that if there is a benefit to a specific ratio between body and fin height, it is not due to momentum enhancement.

Aluminum-based one- and two-dimensional micro fin array structures: high-throughput fabrication and heat transfer testing

NASA Astrophysics Data System (ADS)

Primeaux, Philip A.; Zhang, Bin; Zhang, Xiaoman; Miller, Jacob; Meng, W. J.; KC, Pratik; Moore, Arden L.

2017-02-01

Microscale fin array structures were replicated onto surfaces of aluminum 1100 and aluminum 6061 alloy (Al1100/Al6061) sheet metals through room-temperature instrumented roll molding. Aluminum-based micro fin arrays were replicated at room temperature, and the fabrication process is one with high throughput and low cost. One-dimensional (1D) micro fin arrays were made through one-pass rolling, while two-dimensional (2D) micro fin arrays were made by sequential 90° cross rolling with the same roller sleeve. For roll molding of 1D micro fins, fin heights greater than 600 µm were achieved and were shown to be proportional to the normal load force per feature width. At a given normal load force, the fin height was further shown to scale inversely with the hardness of the sheet metal. For sequential 90° cross rolling, morphologies of roll molded 2D micro fin arrays were examined, which provided clues to understand how plastic deformation occurred under cross rolling conditions. A series of pool boiling experiments on low profile Al micro fin array structures were performed within Novec 7100, a widely used commercial dielectric coolant. Results for both horizontal and vertical surface orientations show that roll molded Al micro fin arrays can increase heat flux at fixed surface temperature as compared to un-patterned Al sheet. The present results further suggest that many factors beyond just increased surface area can influence heat transfer performance, including surface finish and the important multiphase transport mechanisms in and around the fin geometry. These factors must also be considered when designing and optimizing micro fin array structures for heat transfer applications.

Effects of fin clipping on survival and position-holding behavior of brown darters, Etheostoma edwini

USGS Publications Warehouse

Champagne, C.E.; Austin, J.D.; Jelks, H.L.; Jordan, F.

2008-01-01

Advent of the polymerase chain reaction (PCR) has allowed conservation biologists to use small portions of tissue to obtain genetic material for population genetic and taxonomic study. Fin clips are used extensively in large-sized fishes, but it is unclear how clipping enough fin tissue for genetic analysis will affect survival of smaller fishes such as minnows and darters, which are among the most threatened organisms in North America. We tested for effects of fin clipping on survival and swimming performance of non-threatened Brown Darters (Etheostoma edwini) in order to justify similar tissue collection in co-occurring endangered Okaloosa Darters (E. okaloosae). We collected 48 E. edwini from a small stream in northwest Florida, transported them to the laboratory, and randomly assigned them to one of three experimental groups: control, entire right pectoral fin removed, or rear half of caudal fin removed. Successful amplification of DNA indicated that our fin clips were large enough for genetic analysis using PCR. No mortality occurred during a two-month observation period. Fin regeneration was almost complete and we could not visually distinguish clipped fins from control fins after two months. We then randomly assigned fish into the same three experimental groups, clipped fins, and evaluated their ability to hold position at 20 cm/sec in an experimental flow chamber. Neither fish size nor treatment type affected position-holding behavior. Fin clipping does not adversely affect survival and swimming performance of E. edwini maintained in the laboratory. Additional research on the effects of fin clipping on small-sized fishes should be conducted in the field to evaluate survival under natural conditions. ?? 2008 by the American Society of Ichthyologists and Herpetologists.

Methylmercury in dried shark fins and shark fin soup from American restaurants.

PubMed

Nalluri, Deepthi; Baumann, Zofia; Abercrombie, Debra L; Chapman, Demian D; Hammerschmidt, Chad R; Fisher, Nicholas S

2014-10-15

Consumption of meat from large predatory sharks exposes human consumers to high levels of toxic monomethylmercury (MMHg). There also have been claims that shark fins, and hence the Asian delicacy shark fin soup, contain harmful levels of neurotoxic chemicals in combination with MMHg, although concentrations of MMHg in shark fins are unknown. We measured MMHg in dried, unprocessed fins (n=50) of 13 shark species that occur in the international trade of dried shark fins as well as 50 samples of shark fin soup prepared by restaurants from around the United States. Concentrations of MMHg in fins ranged from 9 to 1720 ng/g dry wt. MMHg in shark fin soup ranged from <0.01 to 34 ng/mL, with MMHg averaging 62 ± 7% of total Hg. The highest concentrations of MMHg and total Hg were observed in both fins and soup from large, high trophic level sharks such as hammerheads (Sphyrna spp.). Consumption of a 240 mL bowl of shark fin soup containing the average concentration of MMHg (4.6 ng/mL) would result in a dose of 1.1 μg MMHg, which is 16% of the U.S. EPA's reference dose (0.1 μg MMHg per 1 kg per day in adults) of 7.4 μg per day for a 74 kg person. If consumed, the soup containing the highest measured MMHg concentration would exceed the reference dose by 17%. While shark fin soup represents a potentially important source of MMHg to human consumers, other seafood products, particularly the flesh of apex marine predators, contain much higher MMHg concentrations and can result in substantially greater exposures of this contaminant for people. Copyright © 2014 Elsevier B.V. All rights reserved.

X-38 Seal Development

NASA Technical Reports Server (NTRS)

Curry, Donald M.; Lewis, Ronald K.; Hagen, Jeffrey D.

2002-01-01

An X-38 Crew Return Vehicle Seal Development is presented. The contents include: 1) X-38 Crew Return Vehicle; 2) X-38 TPS Configuration; 3) X-38 Seal Locations; 4) X-38 Rudder/Fin Seal Assembly; 5) Baseline X-38 Rudder/Fin Seal Design; 6) Rudder/Fin Seal to Bracket Assembly; 7) X-38 Rudder/Fin Vertical Rub Surface Inconel-0.10 inches; 8) X-38 Rudder/Fin Seal Analysis; 9) Seal Analysis Model; and 10) Governing Differential Equations for Equilibrium Thermal Assumption. The X-38 Rudder/Fin Seal temperature and pressure properties are also given.

A biorobotic pectoral fin for autonomous undersea vehicles.

PubMed

Tangorra, James L; Davidson, S Naomi; Madden, Peter G; Lauder, George V; Hunter, Ian W

2006-01-01

A biorobotic fin for autonomous undersea vehicles (AUVs) was developed based on studies of the anatomy, kinematics, and hydrodynamics of the bluegill sunfish pectoral fin. The biorobotic fin was able to produce many of the complex fin motions used by the sunfish during steady swimming and was used to investigate mechanisms of thrust production and control. This biorobotic fin is an excellent experimental tool and is an important first step towards developing propulsive devices that give AUVs maneuvering characteristics that match and exceed those of highly maneuverable fish.

Anatomy and muscle activity of the dorsal fins in bamboo sharks and spiny dogfish during turning maneuvers.

PubMed

Maia, Anabela; Wilga, Cheryl D

2013-11-01

Stability and procured instability characterize two opposing types of swimming, steady and maneuvering, respectively. Fins can be used to manipulate flow to adjust stability during swimming maneuvers either actively using muscle control or passively by structural control. The function of the dorsal fins during turning maneuvering in two shark species with different swimming modes is investigated here using musculoskeletal anatomy and muscle function. White-spotted bamboo sharks are a benthic species that inhabits complex reef habitats and thus have high requirements for maneuverability. Spiny dogfish occupy a variety of coastal and continental shelf habitats and spend relatively more time cruising in open water. These species differ in dorsal fin morphology and fin position along the body. Bamboo sharks have a larger second dorsal fin area and proportionally more muscle insertion into both dorsal fins. The basal and radial pterygiophores are plate-like structures in spiny dogfish and are nearly indistinguishable from one another. In contrast, bamboo sharks lack basal pterygiophores, while the radial pterygiophores form two rows of elongated rectangular elements that articulate with one another. The dorsal fin muscles are composed of a large muscle mass that extends over the ceratotrichia overlying the radials in spiny dogfish. However, in bamboo sharks, the muscle mass is divided into multiple distinct muscles that insert onto the ceratotrichia. During turning maneuvers, the dorsal fin muscles are active in both species with no differences in onset between fin sides. Spiny dogfish have longer burst durations on the outer fin side, which is consistent with opposing resistance to the medium. In bamboo sharks, bilateral activation of the dorsal in muscles could also be stiffening the fin throughout the turn. Thus, dogfish sharks passively stiffen the dorsal fin structurally and functionally, while bamboo sharks have more flexible dorsal fins, which result from a steady swimming trade off. Copyright © 2013 Wiley Periodicals, Inc.

Experimental investigation of heat transfer and flow pattern from heated horizontal rectangular fin array under natural convection

NASA Astrophysics Data System (ADS)

Taji, S. G.; Parishwad, G. V.; Sane, N. K.

2014-07-01

This paper presents results of the experimental study conducted on heated horizontal rectangular fin array under natural convection. The temperature mapping and the prediction of the flow patterns over the fin array with variable fin spacing is carried out. Dimensionless fin spacing to height (S/H) ratio is varied from 0.05 to 0.3 and length to height ratio (L/H) = 5 is kept constant. The heater input to the fin array assembly is varied from 25 to 100 W. The single chimney flow pattern is observed from 8 to 12 mm fin spacing. The end flow is choked below 6 mm fin spacing. The single chimney flow pattern changes to sliding or end flow choking at 6 mm fin spacing. The average heat transfer coefficient (ha) is very small (2.52-5.78 W/m2 K) at 100 W for S = 5-12 mm. The ha is very small (1.12-1.8 W/m2 K) at 100 W for 2-4 mm fin spacing due to choked fin array end condition. The end flow is not sufficient to reach up to central portion of fin array and in the middle portion there is an unsteady down and up flow pattern resulting in sliding chimney. The central bottom portion of fin array channel does not contribute much in heat dissipation for S = 2-4 mm. The ha has significantly improved at higher spacing as compared to lower spacing region. The single chimney flow pattern is preferred from heat transfer point of view. The optimum spacing is confirmed in the range of 8-10 mm. The average heat transfer results are compared with previous literature and showed similar trend and satisfactory agreement. An empirical equation has been proposed to correlate the average Nusselt number as a function of Grashof number and fin spacing to height ratio. The average error for this equation is -0.32 %.

Molecular mechanisms underlying the exceptional adaptations of batoid fins.

PubMed

Nakamura, Tetsuya; Klomp, Jeff; Pieretti, Joyce; Schneider, Igor; Gehrke, Andrew R; Shubin, Neil H

2015-12-29

Extreme novelties in the shape and size of paired fins are exemplified by extinct and extant cartilaginous and bony fishes. Pectoral fins of skates and rays, such as the little skate (Batoid, Leucoraja erinacea), show a strikingly unique morphology where the pectoral fin extends anteriorly to ultimately fuse with the head. This results in a morphology that essentially surrounds the body and is associated with the evolution of novel swimming mechanisms in the group. In an approach that extends from RNA sequencing to in situ hybridization to functional assays, we show that anterior and posterior portions of the pectoral fin have different genetic underpinnings: canonical genes of appendage development control posterior fin development via an apical ectodermal ridge (AER), whereas an alternative Homeobox (Hox)-Fibroblast growth factor (Fgf)-Wingless type MMTV integration site family (Wnt) genetic module in the anterior region creates an AER-like structure that drives anterior fin expansion. Finally, we show that GLI family zinc finger 3 (Gli3), which is an anterior repressor of tetrapod digits, is expressed in the posterior half of the pectoral fin of skate, shark, and zebrafish but in the anterior side of the pelvic fin. Taken together, these data point to both highly derived and deeply ancestral patterns of gene expression in skate pectoral fins, shedding light on the molecular mechanisms behind the evolution of novel fin morphologies.

Subsonic Aerodynamic Characteristics of a Circular Body Earth-to-Orbit Vehicle

NASA Technical Reports Server (NTRS)

Lepsch, Roger A., Jr.; Ware, George M.; MacConochie, Ian O.

1996-01-01

A test of a generic reusable earth-to-orbit transport was conducted in the 7- by 10-Foot high-speed tunnel at the Langley Research Center at Mach number 0.3. The model had a body with a circular cross section and a thick clipped delta wing as the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center vertical fin, wingtip fins, and a nose-mounted vertical fin. The configuration was longitudinally stable about the estimated center-of-gravity position of 0.72 body length and had sufficient pitch-control authority for stable trim over a wide range of angle of attack, regardless of fin arrangement. The maximum trimmed lift/drag ratio for the aft center-fin configuration was less than 5, whereas the other configurations had values of above 6. The aft center-fin configuration was directionally stable for all angles of attack tested. The wingtip and nose fins were not intended to produce directional stability but to be active controllers for artificial stabilization. Small rolling-moment values resulted from yaw control of the nose fin. Large adverse rolling-moment increments resulted from tip-fin controller deflection above 13 deg angle of attack. Flow visualization indicated that the adverse rolling-moment increments were probably caused by the influence of the deflected tip-fin controller on wing flow separation.

Wind Tunnel Investigation of Fuselage Stability in Yaw with Various Arrangements of Fins

NASA Technical Reports Server (NTRS)

Hoggard, H Page, Jr

1940-01-01

An investigation was made in the 7-by-10 foot wind tunnel to determine the effects of dorsal-type fins and various arrangements of fins on the aerodynamic characteristics of a streamline circular fuselage. Comparative plots of the aerodynamic characteristics of the fuselage alone and the fuselage with various fin arrangements are given to show their effects on coefficients of yawing moment, drag, and lateral force. Results are also given for one case in which a rear fin on a circular fuselage was faired with modeling clay to obtain a fuselage shape with the same side elevation as the fuselage with the unfaired fin but with an elliptical cross section over the rearward portion of the fuselage. The results indicated that fin area to the rear of the center of gravity of the fuselage was beneficial in reducing the magnitude of the unstable yawing moments at large angles of yaw; whereas, fin area forward of the center of gravity was harmful. The dorsal-type fin was more effective for increasing the yawing stability of the fuselage than was a smoothly faired rearward portion with the same side elevation as the fuselage with the unfaired dorsal type fin. The minimum drag coefficient and the slope of the curve of yawing-moment coefficient of the fuselage at zero yaw were unaffected by the addition of the fins, within the experimental accuracy of the tests.

Molecular mechanisms underlying the exceptional adaptations of batoid fins

PubMed Central

Nakamura, Tetsuya; Klomp, Jeff; Pieretti, Joyce; Schneider, Igor; Gehrke, Andrew R.; Shubin, Neil H.

2015-01-01

Extreme novelties in the shape and size of paired fins are exemplified by extinct and extant cartilaginous and bony fishes. Pectoral fins of skates and rays, such as the little skate (Batoid, Leucoraja erinacea), show a strikingly unique morphology where the pectoral fin extends anteriorly to ultimately fuse with the head. This results in a morphology that essentially surrounds the body and is associated with the evolution of novel swimming mechanisms in the group. In an approach that extends from RNA sequencing to in situ hybridization to functional assays, we show that anterior and posterior portions of the pectoral fin have different genetic underpinnings: canonical genes of appendage development control posterior fin development via an apical ectodermal ridge (AER), whereas an alternative Homeobox (Hox)–Fibroblast growth factor (Fgf)–Wingless type MMTV integration site family (Wnt) genetic module in the anterior region creates an AER-like structure that drives anterior fin expansion. Finally, we show that GLI family zinc finger 3 (Gli3), which is an anterior repressor of tetrapod digits, is expressed in the posterior half of the pectoral fin of skate, shark, and zebrafish but in the anterior side of the pelvic fin. Taken together, these data point to both highly derived and deeply ancestral patterns of gene expression in skate pectoral fins, shedding light on the molecular mechanisms behind the evolution of novel fin morphologies. PMID:26644578

Hydrodynamics of a freely movable flexible fin near the ground

NASA Astrophysics Data System (ADS)

Jeong, Young Dal; Lee, Jae Hwa

2017-11-01

In the present study, a freely movable flexible fin is numerically modelled to investigate the flapping dynamics of the fin near the ground in a Poiseuille flow. A leading edge of the fin is fixed in the streamwise direction, whereas the lateral motion is spontaneously determined by hydrodynamic interaction between the fin and surrounding fluid. When the fin is initially positioned at yo, the fin passively migrates toward another wall-normal position for an equilibrium state by the interaction between passively flapping flexible body and ground. At the equilibrium position, the drag coefficient of the fin (CD) significantly decreases due to decaying of the flapping and low flow velocity and the fin can swim consistently without the time-averaged lateral force. Two distinctive behavior at the transient state (flapping and non-flapping migration modes) and three distinctive behaviors at the equilibrium state (deflected-straight, large- and small-amplitude flapping modes) are observed depending on the bending rigidity (γ) and mass ratio (μ) of the fin. The equilibrium position of the fin is investigated as a function of initial position (yo) , bending rigidity (γ) , mass ratio (μ) and the Reynolds number (Re). This research was supported by the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2017R1D1A1A09000537) and the Ministry of Science, ICT & Future Planning (NRF-2017R1A5A1015311).

Fish Pectoral Fin Hydrodynamics; Part III: Low Dimensional Models via POD Analysis

NASA Astrophysics Data System (ADS)

Bozkurttas, M.; Madden, P.

2005-11-01

The highly complex kinematics of the pectoral fin and the resulting hydrodynamics does not lend itself easily to analysis based on simple notions of pitching/heaving/paddling kinematics or lift/drag based propulsive mechanisms. A more inventive approach is needed to dissect the fin gait and gain insight into the hydrodynamic performance of the pectoral fin. The focus of the current work is on the hydrodynamics of the pectoral fin of a bluegill sunfish in steady forward motion. The 3D, time-dependent fin kinematics is obtained via a stereo-videographic technique. We employ proper orthogonal decomposition to extract the essential features of the fin gait and then use CFD to examine the hydrodynamics of simplified gaits synthesized from the POD modes. The POD spectrum shows that the first two, three and five POD modes capture 55%, 67%, and 80% of the motion respectively. The first three modes are in particular highly distinct: Mode-1 is a ``cupping'' motion where the fin cups forward as it is abducted; Mode-2 is an ``expansion'' motion where the fin expands to present a larger area during adduction and finally Mode-3 involves a ``spanwise flick'' of the dorsal edge of the fin. Numerical simulation of flow past fin gaits synthesized from these modes lead to insights into the mechanisms of thrust production; these are discussed in detail.

Flow-structure Interaction Modeling of a Fish Caudal Fin during Steady Swimming

NASA Astrophysics Data System (ADS)

Liu, Geng; Geng, Biao; Zheng, Xudong; Xue, Qian; Dong, Haibo

2017-11-01

It's widely thought that the flexibilities of fish fins play critical roles in propulsive performance enhancement (such as thrust augment and efficiency improvement) in nature. In order to explore the formation mechanisms of the fish fin's flexible morphing and its hydrodynamic benefits as well, a high-fidelity flow-structure/membrane interaction modeling of the fish caudal fin is conducted in this work. Following the realistic configuration of the fish caudal fin, a thin membrane supported by a series of beams is constructed. The material properties of the membrane and the beams are reversely determined by the realistic fin morphing obtained from the high-speed videos and the high fidelity flow-structure interaction simulations. With the accurate material property, we investigate the interplay between structure, kinematics and fluid flow in caudal fin propulsion. Detailed analyses on the relationship between the flexural stiffness, fin morphing patterns, hydrodynamic forces and vortex dynamics are then conducted.

PNS predictions for supersonic/hypersonic flows over finned missile configurations

NASA Technical Reports Server (NTRS)

Bhutta, Bilal A.; Lewis, Clark H.

1992-01-01

Finned missile design entails accurate and computationally fast numerical techniques for predicting viscous flows over complex lifting configurations at small to moderate angles of attack and over Mach 3 to 15; these flows are often characterized by strong embedded shocks, so that numerical algorithms are also required to capture embedded shocks. The recent real-gas Flux Vector Splitting technique is here extended to investigate the Mach 3 flow over a typical finned missile configuration with/without side fin deflections. Elliptic grid-generation techniques for Mach 15 flows are shown to be inadequate for Mach 3 flows over finned configurations and need to be modified. Fin-deflection studies indicate that even small amounts of missile fin deflection can substantially modify vehicle aerodynamics. This 3D parabolized Navier-Stokes scheme is also extended into an efficient embedded algorithm for studying small axially separated flow regions due to strong fin and control surface deflections.

Experimental investigation of vortices shed by various wing fin configurations. M.S. Thesis. Final Report

NASA Technical Reports Server (NTRS)

Iversen, J.; Moghadam, M.

1981-01-01

Forty-six different fins, which were members of twelve plan-form families, were tested. A two dimensional Boeing single element airfoil at an angle of attack of eight degrees and a sweepback angle of thirty-two was used to simulate a portion of the wing of a generator aircraft. Various free stream velocities were used to test any individual fin at its particular angle of attack. While the fin itself was mounted on the upper surface of the generator model, the angle of attack of each fin was varied until stall was reached and/or passed. The relative fin vortex strengths were measured in two ways. First, the maximum angular velocity of a four blade rotor placed in the fin vortex center was measured with the use of a stroboscope. Second, the maximum rolling moment on a following wing model placed in the fin vortex center was measured by a force balance.

The Influence of Culture on the International Management of Shark Finning

NASA Astrophysics Data System (ADS)

Dell'Apa, Andrea; Chad Smith, M.; Kaneshiro-Pineiro, Mahealani Y.

2014-08-01

Shark finning is prohibited in many countries, but high prices for fins from the Asian market help maintain the international black-market and poaching. Traditional shark fin bans fail to recognize that the main driver of fin exploitation is linked to cultural beliefs about sharks in traditional Chinese culture. Therefore, shark finning should be addressed considering the social science approach as part of the fishery management scheme. This paper investigates the cultural significance of sharks in traditional Chinese and Hawaiian cultures, as valuable examples of how specific differences in cultural beliefs can drive individuals' attitudes toward the property of shark finning. We suggest the use of a social science approach that can be useful in the design of successful education campaigns to help change individuals' attitudes toward shark fin consumption. Finally, alternative management strategies for commercial fishers are provided to maintain self-sustainability of local coastal communities.

The influence of culture on the international management of shark finning.

PubMed

Dell'Apa, Andrea; Smith, M Chad; Kaneshiro-Pineiro, Mahealani Y

2014-08-01

Shark finning is prohibited in many countries, but high prices for fins from the Asian market help maintain the international black-market and poaching. Traditional shark fin bans fail to recognize that the main driver of fin exploitation is linked to cultural beliefs about sharks in traditional Chinese culture. Therefore, shark finning should be addressed considering the social science approach as part of the fishery management scheme. This paper investigates the cultural significance of sharks in traditional Chinese and Hawaiian cultures, as valuable examples of how specific differences in cultural beliefs can drive individuals' attitudes toward the property of shark finning. We suggest the use of a social science approach that can be useful in the design of successful education campaigns to help change individuals' attitudes toward shark fin consumption. Finally, alternative management strategies for commercial fishers are provided to maintain self-sustainability of local coastal communities.

A Method for Prevention of Screaming in Rocket Engines

NASA Technical Reports Server (NTRS)

Kerslake, W. R.; Male, T.

1954-01-01

Lateral and longitudinal combustion-pressure oscillations that occurred in screaming combustion of a 1000-pound-thrust rocket engine using white fuming nitric acid and JP-4 fuel as propellants were successfully prevented by means of longitudinal fins in the combustion chamber. Fin position was critical, and complete attenuation was achieved only when the fins were located in a zone approximately 8 to 16 inches from the injector. Fins located in other zones, that is, near the injector or far downstream from the injector, did not stop the oscillations. When oscillations occurred in finned chambers, the longitudinal mode seemed more dominant than the lateral mode; in chambers without fins, the lateral mode tended to be dominant. The lateral oscillation was distorted and its intensity diminished by the fins. Fins, however, did not affect the frequencies; the longitudinal frequency varied inversely with chamber length, and lateral frequencies varied only slightly from an average of 6000 cycles per second.

Underwater fin swimming in women with reference to fin selection.

PubMed

Pendergast, D R; Mollendorf, J; Logue, C; Samimy, S

2003-01-01

Underwater swimmers use fins, which provide thrust to overcome drag and propel the diver. The type of fin used has been shown to affect diver performance, however data are lacking for women. The oxygen consumption (VdotO2) of swimming as a function of speed, velocity as a function of kick frequency, maximal speed (v), maximal VdotO2 and the maximal thrust were determined for 8 female divers swimming at 1.25 m depth in a 60 m annular pool. VdotO2 increased as a function of v as; 0.52 + -0.485 V + 2.85 V2 (r2 = 0.996) and 0.12 + 1.52 V +1.275 V2 (r2 = 0.999) for high (5 fins) and low (3 fins) groupings, respectively. Splits, vents and flanges did not significantly affect VdotO2. Kick frequency increased linearly with v, with unique slopes for each fin. Maximal VdotO2 was not affect by fin type (1.46 +/- 0.05 l/min). Velocities that could be stained aerobically were 0.60 +/- 0.02 m/sec on average, with the most flexible fin higher (0.71 m/sec). Maximal v averaged 0.87 +/- 0.03 m/sec, with the most rigid fin lower (0.77 m/sec). Maximal thrust was not affected by fin and averaged 104 +/- 9 N. It can be concluded that female divers preferred the most flexible fins, which were also the most economical. This is most likely due to low leg power, which could also explain the absence of differences in maximal thrust and velocity.

Heat exchanger with transpired, highly porous fins

DOEpatents

Kutscher, Charles F.; Gawlik, Keith

2002-01-01

The heat exchanger includes a fin and tube assembly with increased heat transfer surface area positioned within a hollow chamber of a housing to provide effective heat transfer between a gas flowing within the hollow chamber and a fluid flowing in the fin and tube assembly. A fan is included to force a gas, such as air, to flow through the hollow chamber and through the fin and tube assembly. The fin and tube assembly comprises fluid conduits to direct the fluid through the heat exchanger, to prevent mixing with the gas, and to provide a heat transfer surface or pathway between the fluid and the gas. A heat transfer element is provided in the fin and tube assembly to provide extended heat transfer surfaces for the fluid conduits. The heat transfer element is corrugated to form fins between alternating ridges and grooves that define flow channels for directing the gas flow. The fins are fabricated from a thin, heat conductive material containing numerous orifices or pores for transpiring the gas out of the flow channel. The grooves are closed or only partially open so that all or substantially all of the gas is transpired through the fins so that heat is exchanged on the front and back surfaces of the fins and also within the interior of the orifices, thereby significantly increasing the available the heat transfer surface of the heat exchanger. The transpired fins also increase heat transfer effectiveness of the heat exchanger by increasing the heat transfer coefficient by disrupting boundary layer development on the fins and by establishing other beneficial gas flow patterns, all at desirable pressure drops.

Fluid dynamics of flapping aquatic flight in the bird wrasse: three-dimensional unsteady computations with fin deformation.

PubMed

Ramamurti, Ravi; Sandberg, William C; Löhner, Rainald; Walker, Jeffrey A; Westneat, Mark W

2002-10-01

Many fishes that swim with the paired pectoral fins use fin-stroke parameters that produce thrust force from lift in a mechanism of underwater flight. These locomotor mechanisms are of interest to behavioral biologists, biomechanics researchers and engineers. In the present study, we performed the first three-dimensional unsteady computations of fish swimming with oscillating and deforming fins. The objective of these computations was to investigate the fluid dynamics of force production associated with the flapping aquatic flight of the bird wrasse Gomphosus varius. For this computational work, we used the geometry of the wrasse and its pectoral fin, and previously measured fin kinematics, as the starting points for computational investigation of three-dimensional (3-D) unsteady fluid dynamics. We performed a 3-D steady computation and a complete set of 3-D quasisteady computations for a range of pectoral fin positions and surface velocities. An unstructured, grid-based, unsteady Navier-Stokes solver with automatic adaptive remeshing was then used to compute the unsteady flow about the wrasse through several complete cycles of pectoral fin oscillation. The shape deformation of the pectoral fin throughout the oscillation was taken from the experimental kinematics. The pressure distribution on the body of the bird wrasse and its pectoral fins was computed and integrated to give body and fin forces which were decomposed into lift and thrust. The velocity field variation on the surface of the wrasse body, on the pectoral fins and in the near-wake was computed throughout the swimming cycle. We compared our computational results for the steady, quasi-steady and unsteady cases with the experimental data on axial and vertical acceleration obtained from the pectoral fin kinematics experiments. These comparisons show that steady state computations are incapable of describing the fluid dynamics of flapping fins. Quasi-steady state computations, with correct incorporation of the experimental kinematics, are useful when determining trends in force production, but do not provide accurate estimates of the magnitudes of the forces produced. By contrast, unsteady computations about the deforming pectoral fins using experimentally measured fin kinematics were found to give excellent agreement, both in the time history of force production throughout the flapping strokes and in the magnitudes of the generated forces.

Natural convection and radiation heat transfer from an array of inclined pin fins

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alessio, M.E.; Kaminski, D.A.

1989-02-01

Natural convection and radiation from an air-cooled, highly populated pin-fin array were studied experimentally. the effects of pin density, pin length, and the angle of the pin to the horizontal were measured. Previous work by Sparrow and Vemuri treated the case of a vertical base plate with horizontal fins. recently, Sparrow and Vemuri (1986) extended their study to include results for vertical fins with a horizontal down-facing base plate, as well as vertical fins with a horizontal up-facing base plate. In this study, the base plate is maintained in a vertical position and the angle of the pins is variedmore » from the horizontal. The main intent of this study was to compare the performance of inclined pin fins with straight pin fins. In all cases studied, the straight, horizontal fins were superior to the inclined fins. It was possible to obtain a single general correlation of the test data. While this correlation is recommended within the range of parameters that were tested here, one significant parameter, the size of the base plate, was not varied.« less

Experimental parametric study of a biomimetic fish robot actuated by piezoelectric actuators

NASA Astrophysics Data System (ADS)

Wiguna, T.; Park, Hoon C.; Heo, S.; Goo, Nam S.

2007-04-01

This paper presents an experiment and parametric study of a biomimetic fish robot actuated by the Lightweight Piezocomposite Actuator (LIPCA). The biomimetic aspects in this work are the oscillating tail beat motion and shape of caudal fin. Caudal fins that resemble fins of BCF (Body and Caudal Fin) mode fish were made in order to perform parametric study concerning the effect of caudal fin characteristics on thrust production at an operating frequency range. The observed caudal fin characteristics are the shape, stiffness, area, and aspect ratio. It is found that a high aspect ratio caudal fin contributes to high swimming speed. The robotic fish propelled by artificial caudal fins shaped after thunniform-fish and mackerel caudal fins, which have relatively high aspect ratio, produced swimming speed as high as 2.364 cm/s and 2.519 cm/s, respectively, for a 300 V p-p input voltage excited at 0.9 Hz. Thrust performance of the biomimetic fish robot is examined by calculating Strouhal number, Froude number, Reynolds number, and power consumption.

Performance enhancement of fin attached ice-on-coil type thermal storage tank for different fin orientations using constrained and unconstrained simulations

NASA Astrophysics Data System (ADS)

Kim, M. H.; Duong, X. Q.; Chung, J. D.

2017-03-01

One of the drawbacks in latent thermal energy storage system is the slow charging and discharging time due to the low thermal conductivity of the phase change materials (PCM). This study numerically investigated the PCM melting process inside a finned tube to determine enhanced heat transfer performance. The influences of fin length and fin numbers were investigated. Also, two different fin orientations, a vertical and horizontal type, were examined, using two different simulation methods, constrained and unconstrained. The unconstrained simulation, which considers the density difference between the solid and liquid PCM showed approximately 40 % faster melting rate than that of constrained simulation. For a precise estimation of discharging performance, unconstrained simulation is essential. Thermal instability was found in the liquid layer below the solid PCM, which is contrary to the linear stability theory, due to the strong convection driven by heat flux from the coil wall. As the fin length increases, the area affected by the fin becomes larger, thus the discharging time becomes shorter. The discharging performance also increased as the fin number increased, but the enhancement of discharging performance by more than two fins was not discernible. The horizontal type shortened the complete melting time by approximately 10 % compared to the vertical type.

A Joined-Wing Flight Experiment

DTIC Science & Technology

2008-02-01

and fuselage, reference geometry and ventral fins, reference geometry and winglets and finally reference geometry and main gear strut-fins. He...the addition of winglets or strut fins, unless the center of mass was shifted forward [30]. Throughout his analysis it became clear that VA-1...With the addition of winglets or fins placed over the main wheel struts, 02.0≈Δ βN C . The addition of the winglets or strut fins introduces a spiral

Design and Analyze a New Measuring Lift Device for Fin Stabilizers Using Stiffness Matrix of Euler-Bernoulli Beam

PubMed Central

Liang, Lihua; Sun, Mingxiao; Shi, Hongyu; Luan, Tiantian

2017-01-01

Fin-angle feedback control is usually used in conventional fin stabilizers, and its actual anti-rolling effect is difficult to reach theoretical design requirements. Primarily, lift of control torque is a theoretical value calculated by static hydrodynamic characteristics of fin. However, hydrodynamic characteristics of fin are dynamic while fin is moving in waves. As a result, there is a large deviation between actual value and theoretical value of lift. Firstly, the reasons of deviation are analyzed theoretically, which could avoid a variety of interference factors and complex theoretical derivations. Secondly, a new device is designed for direct measurement of actual lift, which is composed of fin-shaft combined mechanism and sensors. This new device can make fin-shaft not only be the basic function of rotating fin, but also detect actual lift. Through analysis using stiffness matrix of Euler-Bernoulli beam, displacement of shaft-core end is measured instead of lift which is difficult to measure. Then quantitative relationship between lift and displacement is defined. Three main factors are analyzed with quantitative relationship. What is more, two installation modes of sensors and a removable shaft-end cover are proposed according to hydrodynamic characteristics of fin. Thus the new device contributes to maintenance and measurement. Lastly, the effectiveness and accuracy of device are verified by contrasting calculation and simulation on the basis of actual design parameters. And the new measuring lift method can be proved to be effective through experiments. The new device is achieved from conventional fin stabilizers. Accordingly, the reliability of original equipment is inherited. The alteration of fin stabilizers is minor, which is suitable for engineering application. In addition, the flexural properties of fin-shaft are digitized with analysis of stiffness matrix. This method provides theoretical support for engineering application by carrying out finite element analysis with computers. PMID:28046122

Assessment of Thermal Performance of Functionally Graded Materials in Longitudinal Fins

NASA Astrophysics Data System (ADS)

Hassanzadeh, R.; Bilgili, M.

2018-01-01

Assessment of the thermal characteristics of materials in heat exchangers with longitudinal fins is performed in the case where a conventional homogeneous material of a longitudinal fin is replaced by a functionally graded one, in which the fin material properties, such as the conductivity, are assumed to be graded as linear and power-law functions along the normal axis from the fin base to the fin tip. The resulting equations are calculated under two (Dirichlet and Neumann) boundary conditions. The equations are solved by an approximate analytical method with the use of the mean value theorem. The results show that the inhomogeneity index of a functionally graded material plays an important role for the thermal energy characteristics in such heat exchangers. In addition, it is observed that the use of such a material in longitudinal fins enhances the rate of heat transfer between the fin surface and surrounding fluid. Hopefully, the results obtained in the study will arouse interest of designers in heat exchange industry.

Study of Swept Angle Effects on Grid Fins Aerodynamics Performance

NASA Astrophysics Data System (ADS)

Faza, G. A.; Fadillah, H.; Silitonga, F. Y.; Agoes Moelyadi, Mochamad

2018-04-01

Grid fin is an aerodynamic control surface that usually used on missiles and rockets. In the recent several years many researches have conducted to develop a more efficient grid fins. There are many possibilities of geometric combination could be done to improve aerodynamics characteristic of a grid fin. This paper will only discuss about the aerodynamics characteristics of grid fins compared by another grid fins with different swept angle. The methodology that used to compare the aerodynamics is Computational Fluid Dynamics (CFD). The result of this paper might be used for future studies to answer our former question or as a reference for related studies.

Investigation of internally finned LED heat sinks

NASA Astrophysics Data System (ADS)

Li, Bin; Xiong, Lun; Lai, Chuan; Tang, Yumei

2018-03-01

A novel heat sink is proposed, which is composed of a perforated cylinder and internally arranged fins. Numerical studies are performed on the natural convection heat transfer from internally finned heat sinks; experimental studies are carried out to validate the numerical results. To compare the thermal performances of internally finned heat sinks and externally finned heat sinks, the effects of the overall diameter, overall height, and installation direction on maximum temperature, air flow and heat transfer coefficient are investigated. The results demonstrate that internally finned heat sinks show better thermal performance than externally finned heat sinks; the maximum temperature of internally finned heat sinks decreases by up to 20% compared with the externally finned heat sinks. The existence of a perforated cylinder and the installation direction of the heat sink affect the thermal performance significantly; it is shown that the heat transfer coefficient of the heat sink with the perforated cylinder is improved greater than that with the imperforated cylinder by up to 34%, while reducing the mass of the heat sink by up to 13%. Project supported by the Scientific Research Fund of Sichuan Provincial Education Department (No. 18ZB0516) and the Sichuan University of Arts and Science (No. 2016KZ009Y).

Singing behavior of fin whales in the Davis Strait with implications for mating, migration and foraging.

PubMed

Simon, Malene; Stafford, Kathleen M; Beedholm, Kristian; Lee, Craig M; Madsen, Peter T

2010-11-01

Most baleen whales undertake migrations between low-latitude breeding grounds and high-latitude feeding grounds. Though little is known about the timing of their migration from the Arctic, fin whales are assumed to undertake a similar migratory pattern. To address questions about habitat use and migrations, the acoustic activity of fin whales in Davis Strait, between Greenland and Canada, was monitored continuously for two years using three bottom-moored acoustic recorders. The acoustic power in the fin whale call frequencies peaked in November-December, showing that fin whales are present in Davis Strait much later in the year than previously expected. The closely timed peaks in song activity and conception time imply that not all fin whales migrate south to mate, but rather start mating at high latitudes rather than or before migrating. Singing activity was strongly linked to daylight hours, suggesting that fin whales might feed during the few daylight hours of the late fall and early Arctic winter. A negative correlation between the advancing sea ice front and power in fin whale frequencies indicates that future changes in sea ice conditions from global warming might change the distribution and migratory patterns of fin whales near the poles.

The origin of a new fin skeleton through tinkering

PubMed Central

Stewart, Thomas A.

2015-01-01

Adipose fins are positioned between the dorsal and caudal fins of many teleost fishes and primitively lack skeleton. In at least four lineages, adipose fins have evolved lepidotrichia (bony fin rays), co-opting the developmental programme for the dermal skeleton of other fins into this new territory. Here I provide, to my knowledge, the first description of lepidotrichia development in an adipose fin, characterizing the ontogeny of the redtail catfish, Phractocephalus hemioliopterus. Development of these fin rays differs from canonical lepidotrich development in the following four ways: skeleton begins developing in adults, not in larvae; rays begin developing at the fin's distal tip, not proximally; the order in which rays ossify is variable, not fixed; and lepidotrichia appear to grow both proximally and distally, not exclusively proximodistally. Lepidotrichia are often wavy, of irregular thickness and exhibit no regular pattern of segmentation or branching. This skeleton is among the most variable observed in a vertebrate appendage, offering a unique opportunity to explore the basis of hypervariation, which is generally assumed to reflect an absence of function. I argue that this variation reflects a lack of canalization as compared with other, more ancient lepidotrichs and suggest developmental context can affect the morphology of serial homologues. PMID:26179803

The evolutionary history of the development of the pelvic fin/hindlimb

PubMed Central

Don, Emily K; Currie, Peter D; Cole, Nicholas J

2013-01-01

The arms and legs of man are evolutionarily derived from the paired fins of primitive jawed fish. Few evolutionary changes have attracted as much attention as the origin of tetrapod limbs from the paired fins of ancestral fish. The hindlimbs of tetrapods are derived from the pelvic fins of ancestral fish. These evolutionary origins can be seen in the examination of shared gene and protein expression patterns during the development of pelvic fins and tetrapod hindlimbs. The pelvic fins of fish express key limb positioning, limb bud induction and limb outgrowth genes in a similar manner to that seen in hindlimb development of higher vertebrates. We are now at a point where many of the key players in the development of pelvic fins and vertebrate hindlimbs have been identified and we can now readily examine and compare mechanisms between species. This is yielding fascinating insights into how the developmental programme has altered during evolution and how that relates to anatomical change. The role of pelvic fins has also drastically changed over evolutionary history, from playing a minor role during swimming to developing into robust weight-bearing limbs. In addition, the pelvic fins/hindlimbs have been lost repeatedly in diverse species over evolutionary time. Here we review the evolution of pelvic fins and hindlimbs within the context of the changes in anatomical structure and the molecular mechanisms involved. PMID:22913749

Progress on the Use of Internal Fins as Barriers to Reduce Magnetization on High Current Density Mono Element Internal Tin Conductors (MEIT)

NASA Astrophysics Data System (ADS)

Zeitlin, Bruce A.; Gregory, Eric; Pyon, Taeyoung; Scanlan, R. M.; Polyanskii, Anatolii A.; Lee, Peter J.

2004-06-01

A number of configurations of a mono element internal tin conductor (MEIT) were fabricated to explore the effect of internal fins on the effective filament size (Deff) and its effect on wire processing. A current density of 2.85 × 109 A/m2 (12 T) was achieved in a high tin, high Nb conductor. Wire lengths as long as 15.8 km at 0.254 mm diameter with breaks averaging 3 per unit length were achieved. Magnetization measurements and Magneto-Optical (MO) images were taken of the finned and non-fin conductor which indicated the fins appeared to be effective. The Deff achieved in the fin conductor was 80 μm compared with an equivalent conductor without a fin of 165 μm.

Effects of Tube Diameter and Tubeside Fin Geometry on the Heat Transfer Performance of Air-Cooled Condensers

NASA Astrophysics Data System (ADS)

Wang, H. S.; Honda, Hiroshi

A theoretical study has been made on the effects of tube diameter and tubeside fin geometry on the heat transfer performance of air-cooled condensers. Extensive numerical calculations of overall heat transfer from refrigerant R410A flowing inside a horizontal microfin tube to ambient air were conducted for a typical operating condition of the air-cooled condenser. The tubeside heat transfer coefficient was calculated by applying a modified stratified flow model developed by Wang et al.8). The numerical results show that the effects of tube diameter, fin height, fin number and helix angle of groove are significant, whereas those of the width of flat portion at the fin tip, the radius of round corner at the fin tip and the fin half tip angle are small.

Numerical studies on heat transfer and pressure drop characteristics of flat finned tube bundles with various fin materials

NASA Astrophysics Data System (ADS)

Peng, Y.; Zhang, S. J.; Shen, F.; Wang, X. B.; Yang, X. R.; Yang, L. J.

2017-11-01

The air-cooled heat exchanger plays an important role in the field of industry like for example in thermal power plants. On the other hand, it can be used to remove core decay heat out of containment passively in case of a severe accident circumstance. Thus, research on the performance of fins in air-cooled heat exchangers can benefit the optimal design and operation of cooling systems in nuclear power plants. In this study, a CFD (Computational Fluid Dynamic) method is implemented to investigate the effects of inlet velocity, fin spacing and tube pitch on the flow and the heat transfer characteristics of flat fins constructed of various materials (316L stainless steel, copper-nickel alloy and aluminium). A three dimensional geometric model of flat finned tube bundles with fixed longitudinal tube pitch and transverse tube pitch is established. Results for the variation of the average convective heat transfer coefficient with respect to cooling air inlet velocity, fin spacing, tube pitch and fin material are obtained, as well as for the pressure drop of the cooling air passing through finned tube. It is shown that the increase of cooling air inlet velocity results in enhanced average convective heat transfer coefficient and decreasing pressure drop. Both fin spacing and tube pitch engender positive effects on pressure drop and have negative effects on heat transfer characteristics. Concerning the fin material, the heat transfer performance of copper-nickel alloy is superior to 316L stainless steel and inferior to aluminium.

The sexually dimorphic adipose fin is an androgen target tissue in the brown trout (Salmo trutta fario).

PubMed

Hisar, Olcay; Sönmez, Adem Yavuz; Hisar, Şükriye Aras; Budak, Harun; Gültepe, Nejdet

2013-04-01

An investigation has been described on the relationship of body length, age and sex with adipose fin length and the number of androgen receptor (AR)-containing cells in the adipose fin as a secondary sexual characteristic for brown trout (Salmo trutta fario). Firstly, body and adipose fin lengths of 2- to 5-year-old brown trout were measured. Thereafter, these fish were killed by decapitation, then their sexes were determined, and adipose fins were excised. The cellular bases of AR binding activities in the adipose fins were analyzed with an antibody against human/rat AR peptide. Immunocytochemistry and western blotting techniques were performed with this antibody. Analysis of morphological measurements indicated that body length and age had a linear relationship with adipose fin length. The coefficients of determination for the body length and age were 0.92 and 0.85 in the male fish and 0.76 and 0.73 in the female fish against the adipose fin length, respectively. At 2 years of age, cells in the adipose fin did not exhibit AR immunoreactivity. However, AR-immunopositive cells were abundant in the adipose fin of 3- to 5-year-old fish. Moreover, the number of AR-immunopositive cells was significantly (P < 0.05) high in males and increased with age. These observations indicate that the adipose fin in the brown trout is a probable target for androgen action and that tissue function or development may to some extent be androgen dependent. In addition, it is likely that such an effect will be mediated by specific androgen receptors.

Ionization detection system for aerosols

DOEpatents

Jacobs, Martin E.

1977-01-01

This invention relates to an improved smoke-detection system of the ionization-chamber type. In the preferred embodiment, the system utilizes a conventional detector head comprising a measuring ionization chamber, a reference ionization chamber, and a normally non-conductive gas triode for discharging when a threshold concentration of airborne particulates is present in the measuring chamber. The improved system utilizes a measuring ionization chamber which is modified to minimize false alarms and reductions in sensitivity resulting from changes in ambient temperature. In the preferred form of the modification, an annular radiation shield is mounted about the usual radiation source provided to effect ionization in the measuring chamber. The shield is supported by a bimetallic strip which flexes in response to changes in ambient temperature, moving the shield relative to the source so as to vary the radiative area of the source in a manner offsetting temperature-induced variations in the sensitivity of the chamber.

Measurements of a Newly Designed BPM for the Tevatron Electron Lens 2

NASA Astrophysics Data System (ADS)

Scarpine, V. E.; Kamerdzhiev, V.; Fellenz, B.; Olson, M.; Kuznetsov, G.; Kamerdzhiev, V.; Shiltsev, V. D.; Zhang, X. L.

2006-11-01

Fermilab has developed a second electron lens (TEL-2) for beam-beam compensation in the Tevatron as part of its Run II upgrade program. Operation of the beam position monitors (BPMs) in the first electron lens (TEL-1) showed a systematic transverse position difference between short proton bunches (2 ns sigma) and long electron pulses (˜1 us) of up to ˜1.5 mm. This difference was attributed to frequency dependence in the BPM system. The TEL-2 BPMs utilize a new, compact four-plate design with grounding strips between plates to minimize crosstalk. In-situ measurements of these new BPMs are made using a stretched wire pulsed with both proton and electron beam formats. In addition, longitudinal impedance measurements of the TEL-2 are presented. Signal processing algorithm studies indicate that the frequency-dependent transverse position offset may be reduced to ˜0.1 mm for the beam structures of interest.

50 CFR 600.1200 - Purpose and scope.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ADMINISTRATION, DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1200 Purpose and scope. The regulations in this subpart govern “shark finning” (the removal of shark fins and discarding of the carcass), the possession of shark fins, and the landing into U.S. ports of shark fins without...

50 CFR 600.1202 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1202 Definitions. (a) In addition... at a dock, berth, beach, seawall, or ramp to begin offloading fish. Shark finning means taking a shark, removing a fin or fins (whether or not including the tail), and returning the remainder of the...

50 CFR 600.1200 - Purpose and scope.

Code of Federal Regulations, 2012 CFR

2012-10-01

... ADMINISTRATION, DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1200 Purpose and scope. The regulations in this subpart govern “shark finning” (the removal of shark fins and discarding of the carcass), the possession of shark fins, and the landing into U.S. ports of shark fins without...

50 CFR 600.1200 - Purpose and scope.

Code of Federal Regulations, 2014 CFR

2014-10-01

... ADMINISTRATION, DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1200 Purpose and scope. The regulations in this subpart govern “shark finning” (the removal of shark fins and discarding of the carcass), the possession of shark fins, and the landing into U.S. ports of shark fins without...

50 CFR 600.1202 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1202 Definitions. (a) In addition... at a dock, berth, beach, seawall, or ramp to begin offloading fish. Shark finning means taking a shark, removing a fin or fins (whether or not including the tail), and returning the remainder of the...

50 CFR 600.1200 - Purpose and scope.

Code of Federal Regulations, 2011 CFR

2011-10-01

... ADMINISTRATION, DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1200 Purpose and scope. The regulations in this subpart govern “shark finning” (the removal of shark fins and discarding of the carcass), the possession of shark fins, and the landing into U.S. ports of shark fins without...

50 CFR 600.1200 - Purpose and scope.

Code of Federal Regulations, 2013 CFR

2013-10-01

... ADMINISTRATION, DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1200 Purpose and scope. The regulations in this subpart govern “shark finning” (the removal of shark fins and discarding of the carcass), the possession of shark fins, and the landing into U.S. ports of shark fins without...

50 CFR 600.1202 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1202 Definitions. (a) In addition... at a dock, berth, beach, seawall, or ramp to begin offloading fish. Shark finning means taking a shark, removing a fin or fins (whether or not including the tail), and returning the remainder of the...

Note: Dynamic analysis of a robotic fish motion with a caudal fin with vertical phase differences

NASA Astrophysics Data System (ADS)

Yun, Dongwon; Kim, Kyung-Soo; Kim, Soohyun; Kyung, Jinho; Lee, Sunghwi

2013-03-01

In this paper, a robotic fish with a caudal fin with vertical phase differences is studied, especially focusing on the energy consumption. Energies for thrusting a conventional robotic fish and one with caudal fin with vertical phase differences are obtained and compared each other. It is shown that a robotic fish with a caudal fin with vertical phase differences can save more energy, which implies the efficient thrusting via a vertically waving caudal fin.

Analytical study on the thermal performance of a partially wet constructal T-shaped fin

NASA Astrophysics Data System (ADS)

Hazarika, Saheera Azmi; Zeeshan, Mohd; Bhanja, Dipankar; Nath, Sujit

2017-07-01

The present paper addresses the thermal analysis of a T-shaped fin under partially wet condition by adopting a cubic variation of the humidity ratio of saturated air with the corresponding fin surface temperature. The point separating the dry and wet parts may lie either in the flange or stem part of the fin and so, two different cases having different governing equations and boundary conditions are analyzed in this paper. Since the governing equations are highly non-linear, they are solved by using an analytical technique called the Differential Transform Method and subsequently, the dry fin length, temperature distribution and fin performances are evaluated and analyzed for a wide range of the various psychometric, geometric and thermo-physical parameters. Finally, it can be highlighted that relative humidity has a pronounced effect on the performance parameters when the fin surface is partially wet whereas this effect is marginally small for fully wet surface.

Mechanism of tonal noise generation from circular cylinder with spiral fin

NASA Astrophysics Data System (ADS)

Yamashita, Ryo; Hayashi, Hidechito; Okumura, Tetsuya; Hamakawa, Hiromitsu

2014-12-01

The pitch of the spiral finned tube influences seriously to the acoustic resonance in the heat exchanger. In this research, the flow characteristics in relating to the aeolian tone from the finned cylinder are studied by the numerical simulation. It is observed that the tonal noise generated from the finned tube at two pitch spaces. The ratio of the fin pitch to the cylinder diameter is changed at 0.11 and 0.27. The tone level increases and the frequency decreases with the pitch shorter. The separation flow from the cylinder generates the span-wise vortices, Karman vortices, and the separation flow from the fin generates the stream-wise vortices. When the fin pitch ratio is small, the stream-wise vortices line up to span-wise and become weak rapidly. Only the Karman vortices are remained and integrate in span. So the Karman vortex became large. This causes the low frequency and the large aeolian tone.

A Study on Aspect Ratio of Heat Dissipation Fin for the Heat Dissipation Performance of Ultra Constant Discharge Lamp

NASA Astrophysics Data System (ADS)

Ko, Dong Guk; Cong Ge, Jun; Im, Ik Tae; Choi, Nag Jung; Kim, Min Soo

2018-01-01

In this study, we analyzed the heat dissipation performance of UCD lamp ballast fin with various aspect ratios. The minimum grid size was 0.02 mm and the number of grid was approximately 11,000. In order to determine the influence of the aspect ratio on the heat dissipation performance of UCD lamp ballast fin, the heat transfer area of the fin was kept constant at 4 mm2. The aspect ratios of the fin were 2 mm: 2 mm (basic model), 1.5 mm: 2.7 mm and 2.7 mm: 1.5 mm, respectively. The heat flux and heat flux time at fin were kept constant at 1×105 W/m2 and 10 seconds, respectively. The heat dissipation performance by the fin was the best at an aspect ratio of 1.5 mm: 2.7 mm.

A shift in anterior–posterior positional information underlies the fin-to-limb evolution

PubMed Central

Onimaru, Koh; Kuraku, Shigehiro; Takagi, Wataru; Hyodo, Susumu; Sharpe, James; Tanaka, Mikiko

2015-01-01

The pectoral fins of ancestral fishes had multiple proximal elements connected to their pectoral girdles. During the fin-to-limb transition, anterior proximal elements were lost and only the most posterior one remained as the humerus. Thus, we hypothesised that an evolutionary alteration occurred in the anterior–posterior (AP) patterning system of limb buds. In this study, we examined the pectoral fin development of catshark (Scyliorhinus canicula) and revealed that the AP positional values in fin buds are shifted more posteriorly than mouse limb buds. Furthermore, examination of Gli3 function and regulation shows that catshark fins lack a specific AP patterning mechanism, which restricts its expression to an anterior domain in tetrapods. Finally, experimental perturbation of AP patterning in catshark fin buds results in an expansion of posterior values and loss of anterior skeletal elements. Together, these results suggest that a key genetic event of the fin-to-limb transformation was alteration of the AP patterning network. DOI: http://dx.doi.org/10.7554/eLife.07048.001 PMID:26283004

Static Longitudinal Stability and Control Characteristics At A Mach Number of 1.99 of a Lenticular-Shaped Reentry Vehicle

NASA Technical Reports Server (NTRS)

Jackson, Charles M., Jr.; Harris, Roy V., Jr.

1960-01-01

An investigation has been made in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.99 to determine the longitudinal stability and control characteristics of a reentry model consisting of a lenticular-shaped body with two fin configurations (horizontal fins with end plates). Effects of deflecting the larger size fins as pitch-control surfaces were also investigated. The results indicate that the body alone was unstable from an angle of attack of 0 deg to about 55 deg where it became stable and remained so to 90 deg. The addition of fins provided positive longitudinal stability throughout the angle-of-attack range and increased the lift-drag ratio of the configuration. Reducing the horizontal-fin area at the inboard trailing edge of the fin had only a small effect on the aerodynamic characteristics of the vehicle for the condition of no fin deflection. Deflecting the fins, appeared to be an effective means of pitch control and had only a small effect on lift-drag ratio.

Performance enhancement in uniaxially tensile stressed GeSn n-channel fin tunneling field-effect transistor: Impact of stress direction

NASA Astrophysics Data System (ADS)

Wang, Hongjuan; Han, Genquan; Jiang, Xiangwei; Liu, Yan; Zhang, Chunfu; Zhang, Jincheng; Hao, Yue

2017-04-01

In this work, the boosting effect on the performance of GeSn n-channel fin tunneling FET (nFinTFET) enabled by uniaxial tensile stress is investigated theoretically. As the fin rotates within the (001) plane, the uniaxial tensile stress is always along its direction. The electrical characteristics of tensile-stressed GeSn nFinTFETs with point and line tunneling modes are computed utilizing the technology computer aided design (TCAD) simulator in which the dynamic nonlocal band-to-band tunneling (BTBT) algorithm is employed. In comparison with the relaxed devices, tensile-stressed GeSn nFinTFETs achieve a substantial enhancement in band-to-band tunneling generation rate (G BTBT) and on-state current I ON owing to the reduced bandgap E G induced by the tensile stress. Performance improvement of GeSn nFinTFETs induced by tensile stress demonstrates a strong dependence on channel direction and tunneling modes. Under the same magnitude of stress, line-nFinTFETs obtain a more pronounced I ON enhancement over the transistors with point tunneling mode.

Analog and RF performance of a multigate FinFET at nano scale

NASA Astrophysics Data System (ADS)

Kumar, Abhishek

2016-12-01

In this paper, analog and RF performance of the Fin field effect transistor (FET) at Nano scale is observed through 3D simulation. FinFET devices like rectangular gate all around (RE-GAA) FinFET, cylindrical gate all around (CY-GAA) FinFET and triple gate (TG) FinFET are observed. The figure of merit (FOMs) such as input-output characteristics, trans-conductance (gm), output-conductance (gd), intrinsic gain (gm/gd), gate capacitance (gate to source and total gate capacitance), unity gain cut-off frequency (ft), trans-conductance generation factor (TGF), gain frequency product (GFP), gain bandwidth product (GBP) and gain transconductance frequency product (GTFP) are observed. The analog performance of a FinFETs are observed by realising source follower circuit with NMOS transistor as a current source. The source follower circuit gain is observed. It has been observed that maximum capacitance is observed in case gate all around condition. Rectangular gate all around has the highest transconductance. In the source follower circuit, the gain curve (Vout/Vin) is sharper for TG-FinFET.

Aerothermoelastic Analysis of a NASP-Like Vertical Fin

NASA Technical Reports Server (NTRS)

Rodgers, John P.

1992-01-01

Several aeroelastic stability analyses for a vertical fin similar to that of the National Aero-Space Plane are described. The objectives of the study were to design and obtain an experimental data base for a supersonic wind-tunnel model of the fin in order to examine the effects of thermal loading on the flutter characteristics. This paper describes the preliminary efforts to design the wind-tunnel model, including several of the geometric parameter variations that were analyzed. The dominant flutter mechanism involved a flap vibration mode and a fin bending mode. Variation of the thicknesses of flap and root flexures, used to attach the flap to the fin, and the fin to a support, significantly affected the flutter boundary. Uniform thermal loads, affecting only material properties, had little effect, as did the application of different uniform temperatures to each side of the fin. In contrast, the application of significant chord-wise thermal gradients induced stresses which reduced the flutter dynamic pressure by as much as 37 percent. For less extreme distributed loading, the low-aspect ratio fin was relatively unaffected.

Fins improve the swimming performance of fish sperm: a hydrodynamic analysis of the Siberian sturgeon Acipenser baerii.

PubMed

Gillies, Eric A; Bondarenko, Volodymyr; Cosson, Jacky; Pacey, Allan A

2013-02-01

The flagella of sturgeon sperm have an ultrastructure comprising paddle-like fins extending along most of their length. These fins are seen in several other marine and freshwater fish. The sperm of these fish are fast swimmers and are relatively short lived: it is therefore tempting to think of these fins as having evolved for hydrodynamic advantage, but the actual advantage they impart, at such a small length scale and slow speed, is unclear. The phrase "the fins improve hydrodynamic efficiency" is commonly found in biological literature, yet little hydrodynamic analysis has previously been used to support such conjectures. In this paper, we examine various hydrodynamic models of sturgeon sperm and investigate both swimming velocity and energy expenditure. All of the models indicate a modest hydrodynamic advantage of finned sperm, in both straight line swimming speed and a hydrodynamic efficiency measure. We find a hydrodynamic advantage for a flagellum with fins, over one without fins, of the order of 15-20% in straight line propulsive velocity and 10-15% in a hydrodynamic efficiency measure. Copyright © 2012 Wiley Periodicals, Inc.

Perforated fins effect on the heat transfer rate from a circular tube by using wind tunnel: An experimental view

NASA Astrophysics Data System (ADS)

Ahmadi Nadooshan, Afshin; Kalbasi, Rasool; Afrand, Masoud

2018-04-01

Perforated fins effects on the heat transfer rate of a circular tube are examined experimentally. An experimental system is set up through the wind tunnel and equipped with necessary measurement tools. Hot water passes through the finned tube and heat transfers to the fin-side air created using the wind tunnel with different velocities. Two fin sets of identical weight are installed on a circular tube with different outer diameters of 22 and 26 mm. The experiments are conducted at two different mass flow rates of the hot water and six Reynolds number of external air flow. Considering the four finned tubes and one no finned tube, a total of 60 tests are conducted. Results showed that with increasing the internal or external flow rates, the effect of larger cross-sectional area is greater. By opening holes on the fins, in addition to weight loss, the maximum heat transfer rate for perforated fins increases by 8.78% and 9.23% respectively for mass flow rates of 0.05 and 0.1 kg/s at low external Reynolds number. While, at high external Reynolds number, the holes reduces heat transfer by 8.4% and 10.6% for mass flow rates of 0.05 and 0.1 kg/s, respectively.

Numerical study of the thermo-flow performances of novel finned tubes for air-cooled condensers in power plant

NASA Astrophysics Data System (ADS)

Guo, Yonghong; Du, Xiaoze; Yang, Lijun

2018-02-01

Air-cooled condenser is the main equipment of the direct dry cooling system in a power plant, which rejects heat of the exhaust steam with the finned tube bundles. Therefore, the thermo-flow performances of the finned tubes have an important effect on the optimal operation of the direct dry cooling system. In this paper, the flow and heat transfer characteristics of the single row finned tubes with the conventional flat fins and novel jagged fins are investigated by numerical method. The flow and temperature fields of cooling air for the finned tubes are obtained. Moreover, the variations of the flow resistance and average convection heat transfer coefficient under different frontal velocity of air and jag number are presented. Finally, the correlating equations of the friction factor and Nusselt number versus the Reynolds number are fitted. The results show that with increasing the frontal velocity of air, the heat transfer performances of the finned tubes are enhanced but the pressure drop will increase accordingly, resulting in the average convection heat transfer coefficient and friction factor increasing. Meanwhile, with increasing the number of fin jag, the heat transfer performance is intensified. The present studies provide a reference in optimal designing for the air-cooled condenser of direct air cooling system.

Performance Analysis of a Self-Propelling Flat Plate Fin with Joint Compliance

NASA Astrophysics Data System (ADS)

Reddy, N. Srinivasa; Sen, Soumen; Pal, Sumit; Shome, Sankar Nath

2017-12-01

Fish fin muscles are compliant and they regulate the stiffness to suit different swimming conditions. This article attempts to understand the significance of presence of compliance in fin muscle with help of a flexible joint flat plate fin model. Blade element method is employed to model hydrodynamics and to compute the forces of interaction during motion of the plate within fluid. The dynamic model of self-propelling fin is developed through multi-body dynamics approach considering the hydrodynamic forces as external forces acting on the fin. The derived hydrodynamic model is validated with experiments on rigid flat plate fin. The effect of the joint stiffness and flapping frequency on the propulsion speed and efficiency is investigated through simulations using the derived and validated model. The propulsion efficiency is found to be highly influenced by the joint stiffness at a given flapping frequency. The fin attained maximum propulsion efficiency when the joint stiffness is tuned to a value at which flapping frequency matches near natural frequency of the fin. At this tuned joint stiffness and flapping frequency, the resulted Strouhal numbers are observed to fall within the optimum range (0.2 to 0.4) for maximized propulsion efficiency of flying birds and swimming aquatic animals reported in literature.

Experimental Study on Cooling Heat Transfer of Supercritical Carbon Dioxide Inside Horizontal Micro-Fin Tubes

NASA Astrophysics Data System (ADS)

Kuwahara, Ken; Higashiiu, Shinya; Ito, Daisuke; Koyama, Shigeru

This paper deals with the experimental study on cooling heat transfer of supercritical carbon dioxide inside micro-fin tubes. The geometrical parameters in micro-fin tubes used in the present study are 6.02 mm in outer diameter, 4.76 mm to 5.11 mm in average inner diameter, 0.15 mm to 0.24 mm in fin height, 5 to 25 in helix angle, 46 to 52 in number of fins and 1.4 to 2.3 in area expansion ratio. Heat transfer coefficients were measured at 8-10 MPa in pressure, 360-690 kg/(m2•s) in mass velocity and 20-75 °C in CO2 temperature. The measured heat transfer coefficients of micro-fin tubes were 1.4 to 2 times higher than those of the smooth tube having 4.42 in inner diameter. The predicted heat transfer coefficients using the correlation equation, which was developed for single-phase turbulent fluid flow inside micro-fin-tubes, showed large deviations to the measured values. The new correlation to predict cooling heat transfer coefficient of supercritical carbon dioxide inside micro-fin tubes was developed taking into account the shape of fins based on experimental data empirically. This correlation equation agreed within ±20% of almost all of the experimental data.

Genetic Architecture of the Variation in Male-Specific Ossified Processes on the Anal Fins of Japanese Medaka.

PubMed

Kawajiri, Maiko; Fujimoto, Shingo; Yoshida, Kohta; Yamahira, Kazunori; Kitano, Jun

2015-10-28

Traits involved in reproduction evolve rapidly and show great diversity among closely related species. However, the genetic mechanisms that underlie the diversification of courtship traits are mostly unknown. Japanese medaka fishes (Oryzias latipes) use anal fins to attract females and to grasp females during courtship; the males have longer anal fins with male-specific ossified papillary processes on the fin rays. However, anal fin morphology varies between populations: the southern populations tend to have longer anal fins and more processes than the northern populations. In the present study, we conducted quantitative trait locus (QTL) mapping to investigate the genetic architecture underlying the variation in the number of papillary processes of Japanese medaka fish and compared the QTL with previously identified QTL controlling anal fin length. First, we found that only a few QTL were shared between anal fin length and papillary process number. Second, we found that the numbers of papillary processes on different fin rays often were controlled by different QTL. Finally, we produced another independent cross and found that some QTL were repeatable between the two crosses, whereas others were specific to only one cross. These results suggest that variation in the number of papillary processes is polygenic and controlled by QTL that are distinct from those controlling anal fin length. Thus, different courtship traits in Japanese medaka share a small number of QTL and have the potential for independent evolution. Copyright © 2015 Kawajiri et al.

A light-colored region of caudal fin: a niche of melanocyte progenitors in crucian carp (Cyprinus carpio L.).

PubMed

Huang, Yaping; Luo, Yurong; Liu, Jinhui; Gui, Saiyu; Wang, Mei; Liu, Wenbin; Peng, Liangyue; Xiao, Yamei

2017-01-01

Melanocyte stem cells are a population of immature cells which sustain the self-renewal and replenish the differentiated melanocytes. In this research, a light-colored region (LCR) is observed at the heel of caudal fin in juvenile crucian carp. By cutting off the caudal fin, the operated caudal fin can regenerate in accordance with the original pigment pattern from the retained LCR. As markers of stem cells, Oct4 and Sox2 have been found to be highly expressed in the LCR as well as Mitfa, a label of the melanoblasts. In vitro, Mitfa + melanoblasts are observed in the cells which are derived from the LCR and transfected with Mitfa-EGFP reporter by using Tol2 transposon system. Furthermore, by real-time qPCR, it is shown that the level of sox2 mRNA is gradually decreased from the LCR to proximal and distal caudal fin, and that of mitfa mRNA in the proximal caudal fin (PCF) is higher than that in the LCR, while it is the lowest in the distal caudal fin. Hence, we propose that the LCR is a pigment progenitor niche, sending melanocytes to the distal of caudal fin, which gradually emerges as caudal fin grow. We reveal that the LCR of caudal fin might be a niche of pigment progenitors, and contribute to pigment-producing stem cells in crucian carp. © 2016 International Federation for Cell Biology.

The effect of traveling wave shapes in the maneuver control and efficiency of an underwater robot propelled by an undulating fin

NASA Astrophysics Data System (ADS)

Liu, Hanlin; Curet, Oscar

2016-11-01

Effective control of propulsive undulating fins has the potential to enhance the maneuverability and efficiency of underwater vehicles allowing them to navigate in more complex environments. Aquatic animals using this type of propulsion are able to perform complex maneuvers by sending different traveling waves along one or multiple elongated fins. Recent work has investigated the propulsive forces, the hydrodynamics and the efficiency of an undulating ribbon fin. However, it is still not understood how different traveling wave shapes along the fin can be used to control the hydrodynamic forces and torques to perform different maneuvers. In this work, we study the effect of traveling wave shapes on the hydrodynamic forces and torques, swimming speed, maneuver control and propulsive performance of an underwater vehicle propelled by an undulating fin. The underwater robot propels by actuating a fin that is composed of sixteen independent rays interconnected with a flexible membrane. The hull contains all the electronics, batteries, motors and sensors. The underwater vehicle was tested in a water tank-flume facility. In a series of experiments, we measured the motion of the vessel and the power consumption for different traveling wave patterns. In addition, we measured the flow around the fin using Particle Image Velocimetry. We present the results concerning the power distribution along the fin, propulsive efficiency, free-swimming speed and pitch control based on different fin kinematics. National Science Foundation under Grant No. 1420774.

Oil-flow study of a Space Shuttle orbiter tip-fin controller

NASA Technical Reports Server (NTRS)

Helms, V. T., III

1983-01-01

Possible use of tip-fin controllers instead of a vertical tail on advanced winged entry vehicles was examined. Elimination of the vertical tail and using tip-fins offers the advantages of positive yaw control at high angles of attack and a potential weight savings. Oil-flow technique was used to obtain surface flow patterns on a tip-fin installed on a 0.01-scale Space Shuttle orbiter model for the purpose of assessing the extent of flow interference effects on the wing and tip-fin which might lead to serious heating problems. Tests were conducted in air at Mach 10 for a free-stream Reynolds numbers of .000113 at 20, 30, and 40 degree angle of attack and sideslip angles of 0 and 2 degree. Elevon deflections of -10, 0, and 10 degree and tip-fin control-surface deflections of 0, 20, and 40 degree were employed. Test results were also used to aid in the interpretation of heating data obtained on a Shuttle orbiter tip-fin on another model in a different facility. A limited comparison of oil-flow patterns and heat-transfer data is included. It was determined that elevon deflection angles from -10 to 10 degree and sideslip angles up to 2 degree have very little effect on tip-fin surface flow patterns. Also, there is a minimum of interference between the tip-fin and the wing. The most significant flow interactions occur on the tip-fin onboard surface as a result of its control-surface deflections.

Characteristics and formation mechanism for stainless steel fiber with periodic micro-fins

NASA Astrophysics Data System (ADS)

Tang, Tao; Wan, Zhenping; Lu, Longsheng; Tang, Yong

2016-05-01

Metal fibers have been widely used in many industrial applications due to their unique advantages. In certain applications, such as catalyst supports or orthopedic implants, a rough surface or tiny outshoots on the surface of metal fibers to increase surface area are needed. However, it has not been concerned about the surface morphologies of metal fiber in the current research of metal fiber manufacturing. In this paper, a special multi-tooth tool composed of a row of triangular tiny teeth is designed. The entire cutting layer of multi-tooth tool bifurcates into several thin cutting layers due to tiny teeth involved in cutting. As a result, several stainless steel fibers with periodic micro-fins are produced simultaneously. Morphology of periodic micro-fins is found to be diverse and can be classified into three categories: unilateral plane, unilateral tapering and bilateral. There are two forming mechanisms for the micro-fins. One is that periodic burrs remained on the free side of cutting layer of a tiny tooth create micro-fins of stainless steel fiber produced by the next neighboring tiny tooth; the other is that the connections between two fibers stuck together come to be micro-fins if the two fibers are finally detached. Influence of cutting conditions on formation of micro-fins is investigated. Experimental results show that cutting depth has no significant effect on micro-fin formation, high cutting speed is conducive to micro-fin formation, and feed should be between 0.12 mm/r and 0.2 mm/r to reliably obtain stainless steel fiber with micro-fins. This research presents a new pattern of stainless steel fiber characterized by periodic micro-fins formed on the edge of fiber and its manufacturing method.

Impact of Channel, Stress-Relaxed Buffer, and S/D Si1- x Ge x Stressor on the Performance of 7-nm FinFET CMOS Design with the Implementation of Stress Engineering

NASA Astrophysics Data System (ADS)

Othman, Nurul Aida Farhana; Hatta, Sharifah Fatmadiana Wan Muhamad; Soin, Norhayati

2018-04-01

Stress-engineered fin-shaped field effect transistors (FinFET) using germanium (Ge) is a promising performance booster to replace silicon (Si) due to its high holes mobility. This paper presents a three-dimensional simulation by the Sentaurus technology computer-aided design to study the effects of stressors—channel stress, stress-relaxed buffer (SRB), and source/drain (S/D) epitaxial stress—on different bases of FinFET, specifically silicon germanium (SiGe) and Ge-based, whereby the latter is achieved by manipulating the Ge mole fraction inside the three layers; their effects on the devices' figures-of-merits were recorded. The simulation generates an advanced calibration process, by which the drift diffusion simulation was adopted for ballistic transport effects. The results show that current enhancement in p-type FinFET (p-FinFET) with 110% is almost twice that in n-type FinFET (n-FinFET) with 57%, with increasing strain inside the channel suggesting that the use of strain is more effective for holes. In SiGe-based n-FinFET, the use of a high-strained SRB layer can improve the drive current up to 112%, while the high-strain S/D epitaxial for Ge-based p-FinFET can enhance the on-state current to 262%. Further investigations show that the channel and S/D doping are affecting the performances of SiGe-based FinFET with similar importance. It is observed that doping concentrations play an important role in threshold voltage adjustment as well as in drive current and subthreshold leakage improvements.

Comparison of the precision of age estimates generated from fin rays, scales, and otoliths of Blue Sucker

USGS Publications Warehouse

Acre, Matthew R.; Alejandrez, Celeste; East, Jessica; Massure, Wade A.; Miyazono, S.; Pease, Jessica E.; Roesler, Elizabeth L.; Williams, H.M.; Grabowski, Timothy B.

2017-01-01

Evaluating the precision of age estimates generated by different readers and different calcified structures is an important part of generating reliable estimations of growth, recruitment, and mortality for fish populations. Understanding the potential loss of precision associated with using structures harvested without sacrificing individuals, such as scales or fin rays, is particularly important when working with imperiled species, such as Cycleptus elongatus (Blue Sucker). We collected otoliths (lapilli), scales, and the first fin rays of the dorsal, anal, pelvic, and pectoral fins of 9 Blue Suckers. We generated age estimates from each structure by both experienced (n = 5) and novice (n = 4) readers. We found that, independent of the structure used to generate the age estimates, the mean coefficient of variation (CV) of experienced readers was approximately 29% lower than that of novice readers. Further, the mean CV of age estimates generated from pectoral-fin rays, pelvic-fin rays, and scales were statistically indistinguishable and less than those of dorsal-fin rays, anal-fin rays, and otoliths. Anal-, dorsal-, and pelvic-fin rays and scales underestimated age compared to otoliths, but age estimates from pectoral-fin rays were comparable to those from otoliths. Skill level, structure, and fish total-length influenced reader precision between subsequent reads of the same aging structure from a particular fish. Using structures that can be harvested non-lethally to estimate the age of Blue Sucker can provide reliable and reproducible results, similar to those that would be expected from using otoliths. Therefore, we recommend the use of pectoral-fin rays as a non-lethal method to obtain age estimates for Blue Suckers.

The dlx5a/dlx6a Genes Play Essential Roles in the Early Development of Zebrafish Median Fin and Pectoral Structures

PubMed Central

Heude, Églantine; Shaikho, Sarah; Ekker, Marc

2014-01-01

The Dlx5 and Dlx6 genes encode homeodomain transcription factors essential for the proper development of limbs in mammalian species. However, the role of their teleost counterparts in fin development has received little attention. Here, we show that dlx5a is an early marker of apical ectodermal cells of the pectoral fin buds and of the median fin fold, but also of cleithrum precursor cells during pectoral girdle development. We propose that early median fin fold establishment results from the medial convergence of dlx5a-expressing cells at the lateral edges of the neural keel. Expression analysis also shows involvement of dlx5a during appendage skeletogenesis. Using morpholino-mediated knock down, we demonstrate that disrupted dlx5a/6a function results in pectoral fin agenesis associated with misexpression of bmp4, fgf8a, and1 and msx genes. In contrast, the median fin fold presents defects in mesenchymal cell migration and actinotrichia formation, whereas the initial specification seems to occur normally. Our results demonstrate that the dlx5a/6a genes are essential for the induction of pectoral fin outgrowth, but are not required during median fin fold specification. The dlx5a/6a knock down also causes a failure of cleithrum formation associated with a drastic loss of runx2b and col10a1 expression. The data indicate distinct requirements for dlx5a/6a during median and pectoral fin development suggesting that initiation of unpaired and paired fin formation are not directed through the same molecular mechanisms. Our results refocus arguments on the mechanistic basis of paired appendage genesis during vertebrate evolution. PMID:24858471

Experimental and Numerical Investigation of Forced Convection Heat Transfer in Heat Sink with Rectangular Plates at Varying Inclinations on Vertical Base

NASA Astrophysics Data System (ADS)

Patil, Harshal Bhauso; Dingare, Sunil Vishnu

2018-03-01

Heat exchange upgrade is a vital territory of research area. Utilization of reasonable systems can bring about noteworthy specialized points of interest coming about reserve funds of cost. Rectangular plates are viewed as best balance arrangement utilized for heat exchange improvement. This gives an enlargement strategy to heat exchange with beginning of limit layer and vortex development. To assess and look at the rate of heat exchange enhancement by rectangular plate fins with differing inclinations (0°-30°-60°), shifting Re and heat supply under forced convection are the principle destinations of this study. The study is done by fluctuating introductions of fins with various inclinations, input heat supply and Re under forced convection. The coefficient of heat transfer increments observed with the expansion in air speed for all the examined designs. The coefficient of the heat transfer is discovered higher at the edge of introduction of fins at 30° for inline arrangement and 0° for staggered arrangement. Looking at both the arrangements, it is discovered that the heat transfer coefficient in 0° fin staggered arrangement is about 17% higher than 30° inline arrangement and 76% higher than the vertical plate fin. For plate fin heat sink, boundary layer formation and growth results in decrease of the coefficient of heat transfer in forced convection. This issue is overcome by accommodating some rectangular fins on the plate fin. It brings about increment of heat transfer coefficient of the RPFHS under the states of trial factors. As indicated by past research, it is discovered that examination of the plate fin heat sink with various sorts of fins for horizontal orientation is done yet but this investigation expects to discover the upgrade of transfer coefficient of plate fin heat sink for its vertical position with rectangular plates at different inclinations under the shifting scopes of heat input supply, fin arrangements and Reynolds number (Re).

Relying on fin erosion to identify hatchery-reared brown trout in a Tennessee river

USGS Publications Warehouse

Meerbeek, Jonathan R.; Bettoli, Phillip William

2012-01-01

Hatchery-induced fin erosion can be used to identify recently stocked catchable-size brown trout Salmo trutta during annual surveys to qualitatively estimate contributions to a fishery. However, little is known about the longevity of this mark and its effectiveness as a short-term (≤ 1 year) mass-marking technique. We evaluated hatchery-induced pectoral fin erosion as a mass-marking technique for short-term stocking evaluations by stocking microtagged brown trout in a tailwater and repeatedly sampling those fish to observe and measure their pectoral fins. At Dale Hollow National Fish Hatchery, 99.1% (228 of 230) of microtagged brown trout in outdoor concrete raceways had eroded pectoral fins 1 d prior to stocking. Between 34 and 68 microtagged and 26-35 wild brown trout were collected during eight subsequent electrofishing samples. In a blind test based on visual examination of pectoral fins at up to 322 d poststocking, one observer correctly identified 91.7% to 100.0% (mean of 96.9%) of microtagged brown trout prior to checking for microtags. In the laboratory, pectoral fin length and width measurements were recorded to statistically compare the fin measurements of wild and microtagged hatchery brown trout. With only one exception, all pectoral fin measurements on each date averaged significantly larger for wild trout than for microtagged brown trout. Based on the number of pectoral fin measurements falling below 95% prediction intervals, 93.7% (148 of 158) of microtagged trout were correctly identified as hatchery fish based on regression models up to 160 d poststocking. Only 72.2% (70 of 97) of microtagged trout were identified correctly after 160 d based on pectoral fin measurements and the regression models. We concluded that visual examination of pectoral fin erosion was a very effective way to identify stocked brown trout for up to 322 d poststocking.

Advances in Understanding the Role of Aerosols on Ice Clouds from the Fifth International Ice Nucleation (FIN) Workshops

NASA Astrophysics Data System (ADS)

Cziczo, D. J.; Moehler, O.; DeMott, P. J.

2015-12-01

The relationship of ambient aerosol particles to the formation of ice-containing clouds is one of the largest uncertainties in understanding climate. This is due to several poorly understood processes including the microphysics of how particles nucleate ice, the number of effective heterogeneous ice nuclei and their atmospheric distribution, the role of anthropogenic activities in producing or changing the behavior of ice forming particles and the interplay between effective heterogeneous ice nuclei and homogeneous ice formation. Our team recently completed a three-part international workshop to improve our understanding of atmospheric ice formation. Termed the Fifth International Ice Nucleation (FIN) Workshops, our motivation was the limited number of measurements and a lack of understanding of how to compare data acquired by different groups. The first activity, termed FIN1, addressed the characterization of ice nucleating particle size, number and chemical composition. FIN2 addressed the determination of ice nucleating particle number density. Groups modeling ice nucleation joined FIN2 to provide insight on measurements critically needed to model atmospheric ice nucleation and to understand the performance of ice chambers. FIN1 and FIN2 took place at the Aerosol Interaction and Dynamics in the Atmosphere (AIDA) chamber at the Karlsruhe Institute of Technology. A particular emphasis of FIN1 and FIN2 was the use of 'blind' intercomparisons using a highly characterized, but unknown to the instrument operators, aerosol sample. The third activity, FIN3, took place at the Desert Research Institute's Storm Peak Laboratory (SPL). A high elevation site not subject to local emissions, SPL allowed for a comparison of ice chambers and subsequent analysis of the ice residuals under the challenging conditions of low particle loading, temperature and pressure found in the atmosphere. The presentation focuses on the improvement in understanding how mass spectra from different instruments can be compared from FIN1 and FIN3. The complementary nature of different ice chamber to access the diverse regimes of temperature and relative humidity space will also be discussed. As a result of the FIN Workshops we believe the performance of instruments in the field can now be quantified and compared.

Developmental change in the function of movement systems: transition of the pectoral fins between respiratory and locomotor roles in zebrafish.

PubMed

Hale, Melina E

2014-07-01

An animal may experience strikingly different functional demands on its body's systems through development. One way of meeting those demands is with temporary, stage-specific adaptations. This strategy requires the animal to develop appropriate morphological states or physiological pathways that address transient functional demands as well as processes that transition morphology, physiology, and function to that of the mature form. Recent research on ray-finned (actinopterygian) fishes is a developmental transition in function of the pectoral fin, thereby providing an opportunity to examine how an organism copes with changes in the roles of its morphology between stages of its life history. As larvae, zebrafish alternate their pectoral fins in coordination with the body axis during slow swimming. The movements of their fins do not appear to contribute to the production of thrust or to stability but instead exchange fluid near the body for cutaneous respiration. The morphology of the larval fin includes a simple stage-specific endoskeletal disc overlaid by fan-shaped adductor and abductor muscles. In contrast, the musculoskeletal system of the mature fin consists of a suite of muscles and bones. Fins are extended laterally during slow swimming of the adult, without the distinct, high-amplitude left-right fin alternation of the larval fin. The morphological and functional transition of the pectoral fin occurs through juvenile development. Early in this period, at about 3 weeks post-fertilization, the gills take over respiratory function, presumably freeing the fins for other roles. Kinematic data suggest that the loss of respiratory function does not lead to a rapid switch in patterns of fin movement but rather that both morphology and movement transition gradually through the juvenile stage of development. Studies relating structure to function often focus on stable systems that are arguably well adapted for the roles they play. Examining how animals navigate transitional periods, when the link of structure to function may be less taut, provides insight both into how animals contend with such change and into the developmental pressures that shape mature form and function. © The Author 2014. Published by Oxford University Press on behalf of the Society for Integrative and Comparative Biology.

Skeletal ontogeny of the vertebral column and of the fins in shi drum Umbrina cirrosa (Teleostei: Perciformes: Sciaenidae), a new candidate species for aquaculture.

PubMed

Neofytou, M; Sfakianakis, D G; Koumoundouros, G; Mylonas, C C; Kentouri, M

2017-09-01

The osteological development of the vertebral column and fins in shi drum Umbrina cirrosa was studied in order to improve knowledge for its introduction in Mediterranean aquaculture. The osteological development was studied in 171 individuals, of total length (L T ) from 2·7 to 30·2 mm that were reared under the mesocosm technique. Vertebral ontogeny starts at 3·4 and 4·0 mm L T , with the formation of the first cartilaginous neural and haemal arches, and spines, respectively, and is completed with the full attainment of epicentrals (12·5 mm L T ). The formation of vertebral centra occurs between 4·1 and 7·4 mm L T . Pectoral supports are the first fin elements to develop (3·0 mm L T ), followed by those of the caudal fin (3·8 mm L T ), pelvic fin (3·9 mm L T ) and finally by those of the dorsal and anal fins (4·5 mm L T ). The caudal fin is the first to develop fin rays and attain the full count of principal fin rays (4·5-6·8 mm L T ), but the last to be fully completed with the formation of procurrent fin rays (6·9-17·5 mm L T ). The next fins starting to present rays are the dorsal (5·3 mm L T ) and the pectoral fins (5·6 mm L T ), while the anal and pelvic fins are the last (5·7 mm L T ). Following the caudal principal fin rays (6·8 mm L T ), the dorsal, anal (6·9 mm L T ), pelvic (7·4 mm L T ) and pectoral fins (9·8 mm L T ) are the next with fully completed ray counts. Aggregation of qualitative changes, such as the appearance of cartilages, the beginning and the complement of the ossification process and the full complement of elements in U. cirrosa were measured as cumulative frequency counts. These measurements reveal three ontogenetic intervals: one very developmentally active period during early life stages (from 3 to 5·9 mm L T ), a second slower developmental period (from 6·0 to 8·9 mm L T ) and finally a period of ontogeny more focused on structure refinement up to metamorphosis and settlement (>9·0 mm L T ). © 2017 The Fisheries Society of the British Isles.

Models of Tidally Induced Gas Filaments in the Magellanic Stream

NASA Astrophysics Data System (ADS)

Pardy, Stephen A.; D’Onghia, Elena; Fox, Andrew J.

2018-04-01

The Magellanic Stream and Leading Arm of H I that stretches from the Large and Small Magellanic Clouds (LMC and SMC) and over 200° of the Southern sky is thought to be formed from multiple encounters between the LMC and SMC. In this scenario, most of the gas in the Stream and Leading Arm is stripped from the SMC, yet recent observations have shown a bifurcation of the Trailing Arm that reveals LMC origins for some of the gas. Absorption measurements in the Stream also reveal an order of magnitude more gas than in current tidal models. We present hydrodynamical simulations of the multiple encounters between the LMC and SMC at their first pass around the Milky Way, assuming that the Clouds were more extended and gas-rich in the past. Our models create filamentary structures of gas in the Trailing Stream from both the LMC and SMC. While the SMC trailing filament matches the observed Stream location, the LMC filament is offset. In addition, the total observed mass of the Stream in these models is underestimated by a factor of four when the ionized component is accounted for. Our results suggest that there should also be gas stripped from both the LMC and SMC in the Leading Arm, mirroring the bifurcation in the Trailing Stream. This prediction is consistent with recent measurements of spatial variation in chemical abundances in the Leading Arm, which show that gas from multiple sources is present, although its nature is still uncertain.

Thermal performance of plate fin heat sink cooled by air slot impinging jet with different cross-sectional area

NASA Astrophysics Data System (ADS)

Mesalhy, O. M.; El-Sayed, Mostafa M.

2015-06-01

Flow and heat transfer characteristics of a plate-fin heat sink cooled by a rectangular impinging jet with different cross-sectional area were studied experimentally and numerically. The study concentrated on investigating the effect of jet width, fin numbers, and fin heights on thermal performance. Entropy generation minimization method was used to define the optimum design and operating conditions. It is found that, the jet width that minimizes entropy generation changes with heat sink height and fin numbers.

Large Scale Density Estimation of Blue and Fin Whales: Utilizing Sparse Array Data to Develop and Implement a New Method for Estimating Blue and Fin Whale Density

DTIC Science & Technology

2015-09-30

1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Large Scale Density Estimation of Blue and Fin Whales ...Utilizing Sparse Array Data to Develop and Implement a New Method for Estimating Blue and Fin Whale Density Len Thomas & Danielle Harris Centre...to develop and implement a new method for estimating blue and fin whale density that is effective over large spatial scales and is designed to cope

Remote control missile model test

NASA Technical Reports Server (NTRS)

Allen, Jerry M.; Shaw, David S.; Sawyer, Wallace C.

1989-01-01

An extremely large, systematic, axisymmetric body/tail fin data base was gathered through tests of an innovative missile model design which is described herein. These data were originally obtained for incorporation into a missile aerodynamics code based on engineering methods (Program MISSILE3), but can also be used as diagnostic test cases for developing computational methods because of the individual-fin data included in the data base. Detailed analysis of four sample cases from these data are presented to illustrate interesting individual-fin force and moment trends. These samples quantitatively show how bow shock, fin orientation, fin deflection, and body vortices can produce strong, unusual, and computationally challenging effects on individual fin loads. Comparisons between these data and calculations from the SWINT Euler code are also presented.

The Species and Origin of Shark Fins in Taiwan's Fishing Ports, Markets, and Customs Detention: A DNA Barcoding Analysis.

PubMed

Chuang, Po-Shun; Hung, Tzu-Chiao; Chang, Hung-An; Huang, Chien-Kang; Shiao, Jen-Chieh

2016-01-01

The increasing consumption of shark products, along with the shark's fishing vulnerabilities, has led to the decrease in certain shark populations. In this study we used a DNA barcoding method to identify the species of shark landings at fishing ports, shark fin products in retail stores, and shark fins detained by Taiwan customs. In total we identified 23, 24, and 14 species from 231 fishing landings, 316 fin products, and 113 detained shark fins, respectively. All the three sample sources were dominated by Prionace glauca, which accounted for more than 30% of the collected samples. Over 60% of the species identified in the fin products also appeared in the port landings, suggesting the domestic-dominance of shark fin products in Taiwan. However, international trade also contributes a certain proportion of the fin product markets, as four species identified from the shark fin products are not found in Taiwan's waters, and some domestic-available species were also found in the customs-detained sample. In addition to the species identification, we also found geographical differentiation in the cox1 gene of the common thresher sharks (Alopias vulpinus), the pelagic thresher shark (A. pelagicus), the smooth hammerhead shark (Sphyrna zygaena), and the scalloped hammerhead shark (S. lewini). This result might allow fishing authorities to more effectively trace the origins as well as enforce the management and conservation of these sharks.

Functional properties of protein from frozen mantle and fin of jumbo squid Dosidicus gigas in function of pH and ionic strength.

PubMed

Rocha-Estrada, J G; Córdova-Murueta, J H; García-Carreño, F L

2010-10-01

Functional properties of protein from mantle and fin of the jumbo squid Dosidicus gigas were explained based on microscopic muscle fiber and protein fractions profiles as observed in SDS-PAGE. Fin has higher content of connective tissue and complex fiber arrangement, and we observed higher hardness of fin gels as expected. Myosin heavy chain (MHC) was found in sarcoplasmic, myofibril and soluble-in-alkali fractions of mantle and only in sarcoplasmic and soluble-in-alkali fractions of fin. An additive effect of salt concentration and pH affected the solubility and foaming properties. Fin and mantle proteins yielded similar results in solubility tests, but significant differences occurred for specific pH and concentrations of salt. Foaming capacity was proportional to solubility; foam stability was also affected by pH and salt concentration. Hardness and fracture strength of fin gels were significantly higher than mantle gels; gels from proteins of both tissues reached the highest level in the folding test. Structural and molecular properties, such as MHC and paramyosin solubility, arrangement of muscle fibers and the content of connective tissue were useful to explain the differences observed in these protein properties. High-strength gels can be formed from squid mantle or fin muscle. Fin displayed similar or better properties than mantle in all tests.

Radiation Effects in Advanced Multiple Gate and Silicon-on-Insulator Transistors

NASA Astrophysics Data System (ADS)

Simoen, Eddy; Gaillardin, Marc; Paillet, Philippe; Reed, Robert A.; Schrimpf, Ron D.; Alles, Michael L.; El-Mamouni, Farah; Fleetwood, Daniel M.; Griffoni, Alessio; Claeys, Cor

2013-06-01

The aim of this review paper is to describe in a comprehensive manner the current understanding of the radiation response of state-of-the-art Silicon-on-Insulator (SOI) and FinFET CMOS technologies. Total Ionizing Dose (TID) response, heavy-ion microdose effects and single-event effects (SEEs) will be discussed. It is shown that a very high TID tolerance can be achieved by narrow-fin SOI FinFET architectures, while bulk FinFETs may exhibit similar TID response to the planar devices. Due to the vertical nature of FinFETs, a specific heavy-ion response can be obtained, whereby the angle of incidence becomes highly important with respect to the vertical sidewall gates. With respect to SEE, the buried oxide in the SOI FinFETs suppresses the diffusion tails from the charge collection in the substrate compared to the planar bulk FinFET devices. Channel lengths and fin widths are now comparable to, or smaller than the dimensions of the region affected by the single ionizing ions or lasers used in testing. This gives rise to a high degree of sensitivity to individual device parameters and source-drain shunting during ion-beam or laser-beam SEE testing. Simulations are used to illuminate the mechanisms observed in radiation testing and the progress and needs for the numerical modeling/simulation of the radiation response of advanced SOI and FinFET transistors are highlighted.

78 FR 36149 - Magnuson-Stevens Act Provisions; Implementation of the Shark Conservation Act of 2010; Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-17

..., transferring or receiving fins from one vessel to another at sea unless the fins are naturally attached to the..., to provide additional time for various stakeholders and other members of the public to submit..., transferring or receiving fins from one vessel to another at sea unless the fins are naturally attached to the...

Utilizing chemo-mechanically functionalized oscillating fins to ``catch and release'' nanoparticles in binary flow

NASA Astrophysics Data System (ADS)

Liu, Ya; Ma, Yongting; Bhattacharya, Amitabh; Kuksenok, Olga; He, Ximin; Aizenberg, Joanna; Balazs, Anna

2013-11-01

In biomimetics, designing an effective ``catch and release'' device for the selective removal of target species from the surrounding solution is critical for developing autonomous sensors and sorters. Using computational simulation, we model an array of oscillating fins that are tethered on the floor of a microchannel and immersed in a binary-fluid stream. During the oscillation, the fins with the specific chemical wetting reach the upper fluid when they are upright and are entirely within the lower stream when they are tilted. We introduce specific adhesive interactions between the fins and particulates in the solution and determine conditions where the oscillating fins can selectively bind (``catch'') target nanoparticles within the upper fluid stream and then release these particles into the lower stream. We isolate the effects of chemical wetting on the fins (e.g., wetting contact angle between fins and fluid) and mechanical parameters (e.g., frequency of fins' oscillations) that lead to the efficient extraction of target species from the upper stream and placement into the lower fluid. Our understanding provides fundamental insights into the system's complex dynamics and mechanism for detection, separation, and purification of multi-component mixtures.

Annular convective-radiative fins with a step change in thickness, and temperature-dependent thermal conductivity and heat transfer coefficient

NASA Astrophysics Data System (ADS)

Barforoush, M. S. M.; Saedodin, S.

2018-01-01

This article investigates the thermal performance of convective-radiative annular fins with a step reduction in local cross section (SRC). The thermal conductivity of the fin's material is assumed to be a linear function of temperature, and heat transfer coefficient is assumed to be a power-law function of surface temperature. Moreover, nonzero convection and radiation sink temperatures are included in the mathematical model of the energy equation. The well-known differential transformation method (DTM) is used to derive the analytical solution. An exact analytical solution for a special case is derived to prove the validity of the obtained results from the DTM. The model provided here is a more realistic representation of SRC annular fins in actual engineering practices. Effects of many parameters such as conduction-convection parameters, conduction-radiation parameter and sink temperature, and also some parameters which deal with step fins such as thickness parameter and dimensionless parameter describing the position of junction in the fin on the temperature distribution of both thin and thick sections of the fin are investigated. It is believed that the obtained results will facilitate the design and performance evaluation of SRC annular fins.

An experimental study of PCM based finned and un-finned heat sinks for passive cooling of electronics

NASA Astrophysics Data System (ADS)

Usman, Hazrat; Ali, Hafiz Muhammad; Arshad, Adeel; Ashraf, Muhammad Junaid; Khushnood, Shahab; Janjua, Muhammad Mansoor; Kazi, S. N.

2018-05-01

This experimental study determines and compares the thermal performance of unfinned and finned PCM based heat sinks. For the analysis considering pin-fins as thermal conductivity enhancer (TCE), triangular configuration is considered. It is further classified into inline and staggered pin-fin arrangements. Three popular variants of paraffin namely paraffin wax, RT-44 and RT-35HC are incorporated as phase change materials (PCMs) inside the heat sink. The volume fraction of pin-fins and PCMs are kept constant at 9% and 90% respectively. The heat input at the base of heat sinks ranges from 5 W to 8 W. The results are presented in two different cases, charging and discharging, and the analysis of temperature variation and comparison of fin arrangements in three different heat sinks with and without PCM. Further the enhancement ratios are determined to quantify the thermal performance in operation time of heat sink for passive cooling with the influence of PCMs and TCEs. The results suggest triangular inline pin-fin as the dominant heat sink geometry and RT-44 as the most efficient PCM for passive thermal management of electronic devices.

Pectoral fin contact as a mechanism for social bonding among dolphins

USGS Publications Warehouse

Dudzinski, Kathleen; Ribic, Christine

2017-01-01

Bottlenose dolphins are large-brained social mammals residing in a fission-fusion society with relationships that are established and maintained over decades. We examined a decade-long data set of inter-individual pectoral fin contact exchanges to better understand how dolphins share information via tactile contact. Sex and age are significant factors in pectoral fin contact within non-kin dolphin dyads. Adult females shared more pectoral fin contacts with other adult females, while younger females showed no pattern of contact. Males shared more pectoral fin contacts with other males as juveniles and as adults, but showed no difference in the number of touches versus rubs as pectoral fin contacts with other males. Whether in the role of initiator as rubber or initiator as rubbee, male dolphins again preferred other males. These results support the notion that dolphins, especially male dolphins, might use pectoral fin contact as one tool in their repertoire for social bonding to establish, maintain and manage their inter-individual relationships. Additionally, it is also likely that the exchange of pectoral fin contact is developed and refined as individuals age, mature socially, and establish their place within a fission-fusion society.

Seasonal and geographical patterns of fin whale song in the western North Atlantic Ocean.

PubMed

Morano, Janelle L; Salisbury, Daniel P; Rice, Aaron N; Conklin, Karah L; Falk, Keri L; Clark, Christopher W

2012-08-01

Male fin whales, Balaenoptera physalus, produce a song consisting of 20 Hz notes at regularly spaced time intervals. Previous studies identified regional differences in fin whale internote intervals (INI), but seasonal changes within populations have not been closely examined. To understand the patterns of fin whale song in the western North Atlantic, the seasonal abundance and acoustic features of fin whale song are measured from two years of archival passive acoustic recordings at two representative locations: Massachusetts Bay and New York Bight. Fin whale 20 Hz notes are detected on 99% of recorded days. In both regions, INI varies significantly throughout the year as two distinct periods: a "short-INI" season in September-January (9.6 s) and a "long-INI" season in March-May (15.1 s). February and June-August are transitional-INI months, with higher variability. Note abundance decreases with increasing INI, where note abundance is significantly lower in April-August than in September-January. Short-INI and high note abundance correspond to the fin whale reproductive season. The temporal variability of INI may be a mechanism by which fin whale individuals encode and communicate a variety of behaviorally relevant information.

Age estimation of burbot using pectoral fin rays, brachiostegal rays, and otoliths

USGS Publications Warehouse

Klein, Zachary B.; Terrazas, Marc M.; Quist, Michael C.

2014-01-01

Throughout much of its native distribution, burbot (Lota lota) is a species of conservation concern. Understanding dynamic rate functions is critical for the effective management of sensitive burbot populations, which necessitates accurate and precise age estimates. Managing sensitive burbot populations requires an accurate and precise non-lethal alternative. In an effort to identify a non-lethal ageing structure, we compared the precision of age estimates obtained from otoliths, pectoral fin rays, dorsal fin rays and branchiostegal rays from 208 burbot collected from the Green River drainage, Wyoming. Additionally, we compared the accuracy of age estimates from pectoral fin rays, dorsal fin rays and branchiostegal rays to those of otoliths. Dorsal fin rays were immediately deemed a poor ageing structure and removed from further analysis. Age-bias plots of consensus ages derived from branchiostegal rays and pectoral fin rays were appreciably different from those obtained from otoliths. Exact agreement between readers and reader confidence was highest for otoliths and lowest for branchiostegal rays. Age-bias plots indicated that age estimates obtained from branchiostegal rays and pectoral fin rays were substantially different from age estimates obtained from otoliths. Our results indicate that otoliths provide the most precise age estimates for burbot.

Morphogen-based simulation model of ray growth and joint patterning during fin development and regeneration.

PubMed

Rolland-Lagan, Anne-Gaëlle; Paquette, Mathieu; Tweedle, Valerie; Akimenko, Marie-Andrée

2012-03-01

The fact that some organisms are able to regenerate organs of the correct shape and size following amputation is particularly fascinating, but the mechanism by which this occurs remains poorly understood. The zebrafish (Danio rerio) caudal fin has emerged as a model system for the study of bone development and regeneration. The fin comprises 16 to 18 bony rays, each containing multiple joints along its proximodistal axis that give rise to segments. Experimental observations on fin ray growth, regeneration and joint formation have been described, but no unified theory has yet been put forward to explain how growth and joint patterns are controlled. We present a model for the control of fin ray growth during development and regeneration, integrated with a model for joint pattern formation, which is in agreement with published, as well as new, experimental data. We propose that fin ray growth and joint patterning are coordinated through the interaction of three morphogens. When the model is extended to incorporate multiple rays across the fin, it also accounts for how the caudal fin acquires its shape during development, and regains its correct size and shape following amputation.

Performance analysis and optimization of radiating fins with a step change in thickness and variable thermal conductivity by homotopy perturbation method

NASA Astrophysics Data System (ADS)

Arslanturk, Cihat

2011-02-01

Although tapered fins transfer more rate of heat per unit volume, they are not found in every practical application because of the difficulty in manufacturing and fabrications. Therefore, there is a scope to modify the geometry of a constant thickness fin in view of the less difficulty in manufacturing and fabrication as well as betterment of heat transfer rate per unit volume of the fin material. For the better utilization of fin material, it is proposed a modified geometry of new fin with a step change in thickness (SF) in the literature. In the present paper, the homotopy perturbation method has been used to evaluate the temperature distribution within the straight radiating fins with a step change in thickness and variable thermal conductivity. The temperature profile has an abrupt change in the temperature gradient where the step change in thickness occurs and thermal conductivity parameter describing the variation of thermal conductivity has an important role on the temperature profile and the heat transfer rate. The optimum geometry which maximizes the heat transfer rate for a given fin volume has been found. The derived condition of optimality gives an open choice to the designer.

Evidence for the secondary sexual development of the anal fin in female kokanee salmon Oncorhynchus nerka.

PubMed

Thorn, M W; Morbey, Y E

2016-02-01

This study examines whether the anal fin undergoes secondary sexual development similar to other reproductive traits in salmonids. This hypothesis was tested by comparing the anal-fin size of female kokanee salmon Oncorhynchus nerka that were in the early and late stages of sexual development. Females in an advanced stage of maturation had significantly larger anal fins relative to females in an early state of maturation (+4-7%), indicating that the anal fin undergoes secondary sexual development. The magnitude of this secondary growth was comparable with snout length (+9-10%), which is known to undergo secondary sexual development in female salmonids. When morphological trait dimensions were compared between the sexes, the anal fin was the only morphological trait found to have a female-biased sexual size dimorphism. This is the first study to show that the anal fin of female salmonids undergoes secondary sexual development. © 2015 The Fisheries Society of the British Isles.

Fgf16 is essential for pectoral fin bud formation in zebrafish

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nomura, Ryohei; Kamei, Eriko; Hotta, Yuuhei

2006-08-18

Zebrafish pectoral fin bud formation is an excellent model for studying morphogenesis. Fibroblast growth factors (Fgfs) and sonic hedgehog (shh) are essential for pectoral fin bud formation. We found that Fgf16 was expressed in the apical ectodermal ridge (AER) of fin buds. A knockdown of Fgf16 function resulted in no fin bud outgrowth. Fgf16 is required for cell proliferation and differentiation in the mesenchyme and the AER of the fin buds, respectively. Fgf16 functions downstream of Fgf10, a mesenchymal factor, signaling to induce the expression of Fgf4 and Fgf8 in the AER. Fgf16 in the AER and shh in themore » zone of polarizing activity (ZPA) interact to induce and/or maintain each other's expression. These findings have revealed that Fgf16, a newly identified AER factor, plays a crucial role in pectoral fin bud outgrowth by mediating the interactions of AER-mesenchyme and AER-ZPA.« less

Formation of a Ge-rich Si1-x Ge x (x > 0.9) fin epitaxial layer condensed by dry oxidation

NASA Astrophysics Data System (ADS)

Jang, Hyunchul; Kim, Byongju; Koo, Sangmo; Ko, Dae-Hong

2017-11-01

We have selectively grown an epitaxial Si0.35Ge0.65 fin layer in a 65 nm oxide trench pattern array and formed a Ge-rich Si1-x Ge x (x > 0.9) fin layer with condensed Ge using dry oxidation. During oxidation of the SiGe fin structure, we found that the compressive strain of the condensed SiGe layer was increased by about 1.3% while Ge was efficiently condensed due to a two-dimensional oxidation reaction. In this paper, we discussed in detail the diffusion during the two-dimensional condensation reaction as well as the asymmetric biaxial strain of the SiGe fin before and after oxidation using a reciprocal space mapping measurement. The application of dry oxidation on selectively grown SiGe fin layer can be an effective method for increasing hole mobility of SiGe fin with increased Ge content and self-induced compressive strain.

A Novel Approach to Model the Air-Side Heat Transfer in Microchannel Condensers

NASA Astrophysics Data System (ADS)

Martínez-Ballester, S.; Corberán, José-M.; Gonzálvez-Maciá, J.

2012-11-01

The work presents a model (Fin1D×3) for microchannel condensers and gas coolers. The paper focusses on the description of the novel approach employed to model the air-side heat transfer. The model applies a segment-by-segment discretization to the heat exchanger adding, in each segment, a specific bi-dimensional grid to the air flow and fin wall. Given this discretization, the fin theory is applied by using a continuous piecewise function for the fin wall temperature. It allows taking into account implicitly the heat conduction between tubes along the fin, and the unmixed air influence on the heat capacity. The model has been validated against experimental data resulting in predicted capacity errors within ± 5%. Differences on prediction results and computational cost were studied and compared with the previous authors' model (Fin2D) and with other simplified model. Simulation time of the proposed model was reduced one order of magnitude respect the Fin2D's time retaining its same accuracy.

Analysis of selected data from the triservice missile data base

NASA Technical Reports Server (NTRS)

Allen, Jerry M.; Shaw, David S.; Sawyer, Wallace C.

1989-01-01

An extremely large, systematic, axisymmetric-body/tail-fin data base has been gathered through tests of an innovative missile model design which is described herein. These data were originally obtained for incorporation into a missile aerodynamics code based on engineering methods (Program MISSILE3), but these data are also valuable as diagnostic test cases for developing computational methods because of the individual-fin data included in the data base. Detailed analyses of four sample cases from these data are presented to illustrate interesting individual-fin force and moment trends. These samples quantitatively show how bow shock, fin orientation, fin deflection, and body vortices can produce strong, unusual, and computationally challenging effects on individual fin loads. Flow-visualization photographs are examined to provide physical insight into the cause of these effects.

Labriform propulsion in fishes: kinematics of flapping aquatic flight in the bird wrasse Gomphosus varius (Labridae)

PubMed

Walker; Westneat

1997-01-01

Labriform, or pectoral fin, propulsion is the primary swimming mode for many fishes, even at high relative speeds. Although kinematic data are critical for evaluating hydrodynamic models of propulsion, these data are largely lacking for labriform swimmers, especially for species that employ an exclusively labriform mode across a broad range of speeds. We present data on pectoral fin locomotion in Gomphosus varius (Labridae), a tropical coral reef fish that uses a lift-based mechanism to fly under water at sustained speeds of 1­6 total body lengths s-1 (TL s-1). Lateral- and dorsal-view video images of three fish swimming in a flow tank at 1­4 TL s-1 were recorded at 60 Hz. From the two views, we reconstructed the three-dimensional motion of the center of mass, the fin tip and two fin chords for multiple fin beats of each fish at each of four speeds. In G. varius, the fin oscillates largely up and down: the stroke plane is tilted by approximately 20 ° from the vertical. Both frequency and the area swept by the pectoral fins increase with swimming speed. Interestingly, there are individual differences in how this area increases. Relative to the fish, the fin tip in lateral view moves along the path of a thin, inclined figure-of-eight. Relative to a stationary observer, the fin tip traces a sawtooth pattern, but the teeth are recumbent (indicating net backwards movement) only at the slowest speeds. Distal fin chords pitch nose downward during the downstroke and nose upward during the upstroke. Hydrodynamic angles of attack are largely positive during the downstroke and negative during the upstroke. The geometry of the fin and incident flow suggests that the fin is generating lift with large upward and small forward components during the downstroke. The negative incident angles during the upstroke suggest that the fin is generating largely thrust during the upstroke. In general, the large thrust is combined with a downward force during the upstroke, but the net backwards motion of the fin at slow speeds generates a small upward component during slow swimming. Both the alternating sign of the hydrodynamic angle of attack and the observed reduced frequencies suggest that unsteady effects are important in G. varius aquatic flight, especially at low speeds. This study provides a framework for the comparison of aquatic flight by fishes with aerial flight by birds, bats and insects.

Fin Ray Stiffness and Fin Morphology Control Ribbon-Fin-Based Propulsion.

PubMed

Liu, Hanlin; Taylor, Bevan; Curet, Oscar M

2017-06-01

Ribbon-fin-based propulsion has rich locomotor capabilities that can enhance the mobility and performance of underwater vehicles navigating in complex environments. Bony fishes using this type of propulsion send one or multiple traveling waves along an elongated fin with the actuation of highly flexible rays that are interconnected by an elastic membrane. In this work, we study how the use of flexible rays and different morphology can affect the performance of ribbon-fin propulsion. We developed a physical model composed of 15 rays that are interconnected with an elastic membrane. We tested four different ray flexural stiffness and four aspect ratios. The robotic model was tested in a low-turbulence flume under two flow conditions ([Formula: see text] wavelength/s). In two experimental sets, we measured fin kinematics, net surge forces, and power consumption. Using these data, we perform a thrust and power analysis of the undulating fin. We present the thrust coefficient, power coefficient, and propulsive efficiency. We find that the thrust generation was linear with the enclosed area swept by the fin, and square of the relative velocity between the incoming flow and traveling wave. The thrust coefficient levels off around 0.5. In addition, for our parameter range, we find that the power consumption scales by the cube of the effective tangential velocity of the rays [Formula: see text] (A is the amplitude of the ray oscillating motion, and [Formula: see text] is the angular velocity). We show that a decay in stiffness decreases both thrust production and power consumption. However, for rays with high flexural stiffness, the difference in thrust compared with rigid rays is minimal. Moreover, our results show that flexible rays can improve the propulsive efficiency compared with a rigid counterpart. Finally, we find that the morphology of ribbon fin affects its propulsive efficiency. For the aspect ratio considered in our experiments, [Formula: see text] was the most efficient compared with [Formula: see text]. Our results suggest that there could be an optimal morphology for a given ribbon fin kinematics. Therefore, both natural swimmers and underwater vehicles using ribbon-fin-based propulsion can take advantage of flexible rays and optimal aspect ratio to improve propulsive performance.

Development of a whole-organism model to screen new compounds for sun protection.

PubMed

Wang, Yun-Hsin; Wen, Chi-Chung; Yang, Zhi-Shiang; Cheng, Chien-Chung; Tsai, Jen-Ning; Ku, Chia-Chen; Wu, Hsin-Ju; Chen, Yau-Hung

2009-01-01

We used zebrafish as a whole-organism model to screen new compounds for sun protection activity. First of all, we designed a series of UVB exposure experiments and recorded the phenotypic changes of zebrafish embryos. Results showed that 100 mJ/cm(2) of UVB given six times separated by 30 min intervals is the best condition. Fin malformation (reduced and/or absent fin) phenotypes are the most evident consequences after exposure to UVB. Each fin was affected by UVB, including pelvic, ventral, caudal, and dorsal fin, but pelvic fin seemed to be the most sensitive target after UVB exposure. We furthermore carried out "prevention" and "treatment" experiments using green tea extract and/or (-)-epigallocatechin (EGCG) to test this whole-organism model by observing the morphological changes of all fins (especially pelvic fin) after UVB exposure. Effects of UVB, green tea extract and EGCG on fin development were assessed using the Kaplan-Meier analysis, log-rank test and Cox proportional hazards regression. Results showed that a zebrafish pelvic fin in the UVB + green tea (treatment) group is 5.51 (range from 2.39 to 14.90) times, one in the UVB + green tea (prevention) group is 7.04 (range from 3.11 to 18.92) times, and one in the 25 ppm of EGCG (prevention) group is 22.19 (range from 9.40 to 61.50) times more likely to return to normal fin than one in the UVB only group. On the basis of these observations, we believe this model is effective for screening the higher stability and lower toxicity of new compounds, such as small chemicals which are derivative from EGCG or other dietary agents for sun protection.

Fish fins as non-lethal surrogates for muscle tissues in freshwater food web studies using stable isotopes.

PubMed

Hette Tronquart, Nicolas; Mazeas, Laurent; Reuilly-Manenti, Liana; Zahm, Amandine; Belliard, Jérôme

2012-07-30

Dorsal white muscle is the standard tissue analysed in fish trophic studies using stable isotope analyses. However, sampling white muscle often implies the sacrifice of fish. Thus, we examined whether the non-lethal sampling of fin tissue can substitute muscle sampling in food web studies. Analysing muscle and fin δ(15)N and δ(13)C values of 466 European freshwater fish (14 species) with an elemental analyser coupled with an isotope ratio mass spectrometer, we compared the isotope values of the two tissues. Correlations between fin and muscle isotope ratios were examined for all fish together and specifically for 12 species. We further proposed four methods of assessing muscle from fin isotope ratios and estimated the errors made using these muscle surrogates. Despite significant differences between isotope values of the two tissues, fin and muscle isotopic signals are strongly correlated. Muscle values, estimated with raw fin isotope ratios (1st method), induce an error of ca. 1‰ for both isotopes. In comparison, specific (2nd method) or general (3rd method) correlations provide meaningful corrections of fin isotope ratios (errors <0.6‰). On the other hand, relationships, established for Australian tropical fish, only give poor muscle estimates (errors >0.8‰). There is little chance that a global model can be created. However, the 2nd and 3rd methods of estimating muscle values from fin isotope ratios should provide an acceptable level of error for the studies of European freshwater food web. We thus recommend that future studies use fin tissue as a non-lethal surrogate for muscle. Copyright © 2012 John Wiley & Sons, Ltd.

Effects of anisotropic conduction and heat pipe interaction on minimum mass space radiators

NASA Technical Reports Server (NTRS)

Baker, Karl W.; Lund, Kurt O.

1991-01-01

Equations are formulated for the two dimensional, anisotropic conduction of heat in space radiator fins. The transverse temperature field was obtained by the integral method, and the axial field by numerical integration. A shape factor, defined for the axial boundary condition, simplifies the analysis and renders the results applicable to general heat pipe/conduction fin interface designs. The thermal results are summarized in terms of the fin efficiency, a radiation/axial conductance number, and a transverse conductance surface Biot number. These relations, together with those for mass distribution between fins and heat pipes, were used in predicting the minimum radiator mass for fixed thermal properties and fin efficiency. This mass is found to decrease monotonically with increasing fin conductivity. Sensitivities of the minimum mass designs to the problem parameters are determined.

Performance of a three-dimensional Navier-Stokes code on CYBER 205 for high-speed juncture flows

NASA Technical Reports Server (NTRS)

Lakshmanan, B.; Tiwari, S. N.

1987-01-01

A vectorized 3D Navier-Stokes code has been implemented on CYBER 205 for solving the supersonic laminar flow over a swept fin/flat plate junction. The code extends MacCormack's predictor-corrector finite volume scheme to a generalized coordinate system in a locally one dimensional time split fashion. A systematic parametric study is conducted to examine the effect of fin sweep on the computed flow field. Calculated results for the pressure distribution on the flat plate and fin leading edge are compared with the experimental measurements of a right angle blunt fin/flat plate junction. The decrease in the extent of the separated flow region and peak pressure on the fin leading edge, and weakening of the two reversed supersonic zones with increase in fin sweep have been clearly observed in the numerical simulation.

Investigation of Ejection Releases of an MB-1 Rocket from a 0.04956-Scaled Model of the Convair F-106A Airplane at Several Mach Numbers and Simulated Altitudes

NASA Technical Reports Server (NTRS)

Lee, J. B.; Basford, R. C.

1957-01-01

As a continuation of an investigation of the ejection release characteristics of an internally carried MB-1 rocket in the Convair F-106A airplane, fin modifications at additional Mach numbers and simulated altitudes have been studied in the 27- by 27-inch preflight jet of the Langley Pilotless Aircraft Research Station at Wallops Island, Va. The MB-1 rocket was ejected with fins open, fins closed, fins closed with a shroud around the fins, and fins folded with a "boattail" placed in between the fins. Dynamically scaled models (0.0^956 scale) were tested at simulated altitudes of 12,000, 18,850, and 27,500 feet at subsonic Mach numbers and at 18,850, 27,500, and 40,000 feet for Mach numbers of 1-39, 1-59, and 1.98. Successful ejections can be obtained for over 10 store diameters from release point by the use of a shroud around the folded fins with the proper ejection velocity and nose-down pitching moment at release. In one case investigated it was found desirable to close off the front one-third of the bomb bay. It appeared that the fins should be opened after release and within 5 "to 6 rocket diameters if no modifications are made on the rocket. An increase in fuselage angle of attack caused higher nose-up pitch rates after release.

Large Scale Density Estimation of Blue and Fin Whales (LSD)

DTIC Science & Technology

2015-09-30

1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Large Scale Density Estimation of Blue and Fin Whales ...sensors, or both. The goal of this research is to develop and implement a new method for estimating blue and fin whale density that is effective over...develop and implement a density estimation methodology for quantifying blue and fin whale abundance from passive acoustic data recorded on sparse

Evaluation of fins used in underwater swimming.

PubMed

Pendergast, D R; Mollendorf, J; Logue, C; Samimy, S

2003-01-01

Underwater swimmers use fins which augment thrust to overcome drag and propel the diver. The VdotO2 of swimming as a function of speed, velocity as a function of kick frequency, maximal speed (v), maximal oxygen consumption (VdotO2) and the maximal thrust were determined for eight fins in 10 male divers swimming at 1.25 m depth in a 60 m annular pool. A theoretical analysis of fin cycles was also performed. VdotO2 increased as a second order polynomial as a function of velocity; VdotO2 = 0.045 + 1.65B V + 1.66 (2) V2 (r2 = 0.997), VdotO2 = 0.25 + 1.03 V + 1.83 V2 (r2 = 0.997) and VdotO2 = -0.15 + 2.26 V + 1.49 V2 (r2 = 0.997), for least, average and most economical fins respectively. Kick frequency increased linearly with velocity and had a unique movement path (signature), giving theoretical values that agreed with the measured thrust, drag and efficiency. In conclusion, virtually all thrust comes from the downward power stroke, with rigid fins kicked deep (high drag), while flexible fins are kicked less deep but with higher frequency (low efficiency). Kick depth and frequency explain the performance of the eight tested fins, and should be optimized to enhance diver performance.

Impact of residual defects caused by extension ion implantation in FinFETs on parasitic resistance and its fluctuation

NASA Astrophysics Data System (ADS)

Matsukawa, Takashi; Liu, Yongxun; Mori, Takahiro; Morita, Yukinori; Otsuka, Shintaro; O'uchi, Shin-ichi; Fuketa, Hiroshi; Migita, Shinji; Masahara, Meishoku

2017-06-01

The influence of extension doping on parasitic resistance and its variability has been investigated for FinFETs. Electrical characterization of FinFETs and crystallinity evaluation of the doped fin structure are carried out for different fin thicknesses and different donor species for ion implantation, i.e., As and P. Reducing the fin thickness and the use of donor species with a larger mass cause serious degradation in the variability and median value of the parasitic resistance. Crystallinity evaluation by transmission electron microscope reveals that significant crystal defects remain after dopant activation annealing for the cases of smaller fin thickness and the implanted dopant with a larger mass. The unrecovered defects cause serious degradation in the parasitic resistance and its variability. In 1998, he joined the Electrotechnical Laboratory, which is former organization of National Institute of Advanced Industrial Science and Technology (AIST). He has been working on development of front-end process technology, variability issues of the FinFETs and technologies for suppressing the variability. He is now a group leader of the AIST and leads the research on the silicon-based CMOS devices. He is a member of the IEEE Electron Devices Society, and the Japan Society of Applied Physics.

Static Longitudinal Stability of a Rocket Vehicle Having a Rear-Facing Step Ahead of the Stabilizing Fins

NASA Technical Reports Server (NTRS)

Keynton, Robert J.

1961-01-01

Tests were conducted at Mach numbers of 3.96 and 4.65 in the Langley Unitary Plan wind tunnel to determine the static longitudinal stability characteristics of a fin-stabilized rocket-vehicle configuration which had a rearward facing step located upstream of the fins. Two fin sizes and planforms, a delta and a clipped delta, were tested. The angle of attack was varied from 6 deg to -6 deg and the Reynolds number based on model 6 length was about 10 x 10. The configuration with the larger fins (clipped delta) had a center of pressure slightly rearward of and an initial normal-force-curve slope slightly higher than that of the configuration with the smaller fins (delta) as would be expected. Calculations of the stability parameters gave a slightly lower initial slope of the normal-force curve than measured data, probably because of boundary-layer separation ahead of the step. The calculated center of pressure agreed well with the measured data. Measured and calculated increments in the initial slope of the normal-force curve and in the center of pressure, due to changing fins, were in excellent agreement indicating that separated flow downstream of the step did not influence flow over the fins. This result was consistent with data from schlieren photographs.

Large electron concentration modulation using capacitance enhancement in SrTiO{sub 3}/SmTiO{sub 3} Fin-field effect transistors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verma, Amit, E-mail: averma@cornell.edu; Nomoto, Kazuki; School of Electrical and Computer Engineering, Cornell University, Ithaca, New York 14853

2016-05-02

Solid-state modulation of 2-dimensional electron gases (2DEGs) with extreme (∼3.3 × 10{sup 14 }cm{sup −2}) densities corresponding to 1/2 electron per interface unit cell at complex oxide heterointerfaces (such as SrTiO{sub 3}/GdTiO{sub 3} or SrTiO{sub 3}/SmTiO{sub 3}) is challenging because it requires enormous gate capacitances. One way to achieve large gate capacitances is by geometrical capacitance enhancement in fin structures. In this work, we fabricate both Au-gated planar field effect transistors (FETs) and Fin-FETs with varying fin-widths on 60 nm SrTiO{sub 3}/5 nm SmTiO{sub 3} thin films grown by hybrid molecular beam epitaxy. We find that the FinFETs exhibit higher gate capacitance comparedmore » to planar FETs. By scaling down the SrTiO{sub 3}/SmTiO{sub 3} fin widths, we demonstrate further gate capacitance enhancement, almost twice compared to the planar FETs. In the FinFETs with narrowest fin-widths, we demonstrate a record 2DEG electron concentration modulation of ∼2.4 × 10{sup 14 }cm{sup −2}.« less

Neural network detected in a presumed vestigial trait: ultrastructure of the salmonid adipose fin

PubMed Central

Buckland-Nicks, J. A.; Gillis, M.; Reimchen, T. E.

2012-01-01

A wide variety of rudimentary and apparently non-functional traits have persisted over extended evolutionary time. Recent evidence has shown that some of these traits may be maintained as a result of developmental constraints or neutral energetic cost, but for others their true function was not recognized. The adipose fin is small, fleshy, non-rayed and located between the dorsal and caudal fins on eight orders of basal teleosts and has traditionally been regarded as vestigial without clear function. We describe here the ultrastructure of the adipose fin and for the first time, to our knowledge, present evidence of extensive nervous tissue, as well as an unusual subdermal complex of interconnected astrocyte-like cells equipped with primary cilia. The fin contains neither adipose tissue nor fin rays. Many fusiform actinotrichia, comprising dense striated macrofibrils, support the free edge and connect with collagen cables that link the two sides. These results are consistent with a recent hypothesis that the adipose fin may act as a precaudal flow sensor, where its removal can be detrimental to swimming efficiency in turbulent water. Our findings provide insight to the broader themes of function versus constraints in evolutionary biology and may have significance for fisheries science, as the adipose fin is routinely removed from millions of salmonids each year. PMID:21733904

Control characteristics for wrap-around fins on cruise missiles configurations

NASA Technical Reports Server (NTRS)

Sawyer, W. C.; Monta, W. J.; Carter, W. V.; Alexander, W. K.

1981-01-01

This paper presents selected results of a panel loads study conducted as part of the final phase of an extensive investigation of an air-breathing missile concept employing wrap-around aerodynamic surfaces. Typical results for M = 2.36 are presented for the fin load results, plus a brief review of basic results of the previously reported tests. Vapor screen results are also discussed. The present results indicate that the fin load characteristics are nearly identical for planar and curved fins having the same projected planform and would permit the use of planar-surface predictions for supersonic speeds in the preliminary design stages of missiles employing wrap-around curved fins.

Cooled particle accelerator target

DOEpatents

Degtiarenko, Pavel V.

2005-06-14

A novel particle beam target comprising: a rotating target disc mounted on a retainer and thermally coupled to a first array of spaced-apart parallel plate fins that extend radially inwardly from the retainer and mesh without physical contact with a second array of spaced-apart parallel plate fins that extend radially outwardly from and are thermally coupled to a cooling mechanism capable of removing heat from said second array of spaced-apart fins and located within the first array of spaced-apart parallel fins. Radiant thermal exchange between the two arrays of parallel plate fins provides removal of heat from the rotating disc. A method of cooling the rotating target is also described.

Tunnel FinFET CMOS inverter with very low short-circuit current for ultralow-power Internet of Things application

NASA Astrophysics Data System (ADS)

Morita, Yukinori; Fukuda, Koichi; Liu, Yongxun; Mori, Takahiro; Mizubayashi, Wataru; O'uchi, Shin-ichi; Fuketa, Hiroshi; Otsuka, Shintaro; Migita, Shinji; Masahara, Meishoku; Endo, Kazuhiko; Ota, Hiroyuki; Matsukawa, Takashi

2017-04-01

We have demonstrated the operation of a CMOS inverter consisting of Si tunnel FinFETs. Both p- and n-type tunnel FinFETs are successfully fabricated and operated on the same SOI wafer. The current mismatch between p- and n-type tunnel FETs is compensated by tuning the number of fin channels. Very low short-circuit current and clear voltage input-output characteristics are obtained. The thin epitaxial channel in the tunnel FinFETs effectively increases the drain current and accordingly reduces the drain capacitance, which could help high-performance tunnel FET CMOS inverter operation.

The Effect of Fin Pitch on Fluid Elastic Instability of Tube Arrays Subjected to Cross Flow of Water

NASA Astrophysics Data System (ADS)

Desai, Sandeep Rangrao; Pavitran, Sampat

2018-02-01

Failure of tubes in shell and tube exchangers is attributed to flow induced vibrations of such tubes. There are different excitations mechanisms due to which flow induced vibration occurs and among such mechanisms, fluid elastic instability is the most prominent one as it causes the most violent vibrations and may lead to rapid tube failures within short time. Fluid elastic instability is the fluid-structure interaction phenomenon which occurs when energy input by the fluid force exceeds energy expended in damping. This point is referred as instability threshold and corresponding velocity is referred as critical velocity. Once flow velocity exceeds critical flow velocity, the vibration amplitude increases very rapidly with flow velocity. An experimental program is carried out to determine the critical velocity at instability for plain and finned tube arrays subjected to cross flow of water. The tube array geometry is parallel triangular with cantilever end condition and pitch ratios considered are 2.6 and 2.1. The objective of research is to determine the effect of increase in pitch ratio on instability threshold for plain tube arrays and to assess the effect of addition of fins as well as increase in fin density on instability threshold for finned tube arrays. Plain tube array with two different pitch ratios; 2.1 and 2.6 and finned tube arrays with same pitch ratio; 2.6 but with two different fin pitches; such as fine (10 fpi) and coarse (4 fpi) are considered for the experimentation. Connors' equation that relates critical velocity at instability to different parameters, on which instability depends, has been used as the basis for analysis and the concept of effective diameter is used for the present investigation. The modal parameters are first suitably modified using natural frequency reduction setup that is already designed and developed to reduce natural frequency and hence to achieve experimental simulation of fluid elastic instability within the limited flow capacity of the pump. The tests are carried out first on plain tube arrays to establish the same as the datum case and results are compared to known results of plain tube arrays and hence the quality of the test rig is also assessed. The fluid elastic vibration tests are then carried out on finned tube arrays with coarse and fine fin pitches and effects of fins and fin pitch on instability threshold are shown. The vibration response of the tube is recorded for each gradually increasing flow rates of water till instability point is reached. The parameters at the instability are then presented in terms of dimensionless parameters to compare them with published results. It is concluded that, arrays with higher pitch ratios are unstable at comparatively higher flow velocities and instability threshold for finned tube arrays is delayed due to addition of the fins. Further, it is concluded that, instability threshold for finned tube arrays with fine fin pitch is delayed compared to coarse fin pitch and hence for increased fin density, instability threshold is delayed. The experimental results in terms of critical velocities obtained for different tube arrays subjected to water cross flow will serve as the base flow rates for air-water cross flow experiments to be conducted in the next phase.

Low cost impulse compatible wideband antenna

DOEpatents

Rosenbury, Erwin T.; Burke, Gerald J.; Nelson, Scott D.; Stever, Robert D.; Governo, George K.; Mullenhoff, Donald J.

2002-01-01

An antenna apparatus and method for building the antenna is disclosed. Impulse signals travel through a feed point of the antenna with respect to a ground plane. A geometric fin structure is connected to the feed point, and through a termination resistance to the ground plane. A geometric ridge structure connected to the ground is positioned with respect to the fin in order to receive and radiate electromagnetic energy from the impulse signal at a predetermined impedance and over a predetermined set of frequencies. The fin and ridge can be either a wire or a planar surface. The fin and ridge may be disposed within a radiation cavity such as a horn. The radiation cavity is constructed of stamped and etched metal sheets bent and then soldered together. The fin and ridge are also formed from metal sheets or wires. The fin is attached to the feed point and then to the cavity through a termination resistance. The ridge is attached to the cavity and disposed with respect to the fin in order to achieve a particular set of antenna characteristics.

Measurement of frost characteristics on heat exchanger fins. Part 1: Test facility and instrumentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, L.; Chen, H.; Besant, R.W.

1999-07-01

A special test facility was developed to characterize frost growing on heat exchanger fins where the cold surfaces and the air supply conditions were similar to those experienced in freezers, i.e., cold surface temperatures ranging from {minus}35 C to {minus}40 C, air supply temperatures from {minus}10 C to {minus}20 C, and 80% to 100% relative humidity (RH). This test facility included a test section with removable fins to measure the frost height and mass concentration. Frost height on heat exchanger fins was measured using a new automated laser scanning system to measure the height of frost and its distribution onmore » selected fins. The increase in air pressure loss resulting from frost growth on the fins was measured directly in the test loop. The frost mass accumulation distribution was measured for each test using special pre-etched fins that could be easily subdivided and weighed. The total heat rate was measured using a heat flux meter. These frost-measuring instruments were calibrated and the uncertainty of each is stated.« less

Fish robotics and hydrodynamics

NASA Astrophysics Data System (ADS)

Lauder, George

2010-11-01

Studying the fluid dynamics of locomotion in freely-swimming fishes is challenging due to difficulties in controlling fish behavior. To provide better control over fish-like propulsive systems we have constructed a variety of fish-like robotic test platforms that range from highly biomimetic models of fins, to simple physical models of body movements during aquatic locomotion. First, we have constructed a series of biorobotic models of fish pectoral fins with 5 fin rays that allow detailed study of fin motion, forces, and fluid dynamics associated with fin-based locomotion. We find that by tuning fin ray stiffness and the imposed motion program we can produce thrust both on the fin outstroke and instroke. Second, we are using a robotic flapping foil system to study the self-propulsion of flexible plastic foils of varying stiffness, length, and trailing edge shape as a means of investigating the fluid dynamic effect of simple changes in the properties of undulating bodies moving through water. We find unexpected non-linear stiffness-dependent effects of changing foil length on self-propelled speed, and as well as significant effects of trailing edge shape on foil swimming speed.

Functional morphology of the radialis muscle in shark tails.

PubMed

Flammang, Brooke E

2010-03-01

The functional morphology of intrinsic caudal musculature in sharks has not been studied previously, though the kinematics and function of body musculature have been the focus of a great deal of research. In the tail, ventral to the axial myomeres, there is a thin strip of red muscle with fibers angled dorsoposteriorly, known as the radialis. This research gives the first anatomical description of the radialis muscle in sharks, and addresses the hypothesis that the radialis muscle provides postural stiffening in the tail of live swimming sharks. The radialis muscle fibers insert onto the deepest layers of the stratum compactum, the more superior layers of which are orthogonally arrayed and connect to the epidermis. The two deepest layers of the stratum compactum insert onto the proximal ends of the ceratotrichia of the caudal fin. This anatomical arrangement exists in sharks and is modified in rays, but was not found in skates or chimaeras. Electromyography of the caudal muscles of dogfish swimming steadily at 0.25 and 0.5 body lengths per second (Ls(-1)) exhibited a pattern of anterior to posterior activation of the radialis muscle, followed by activation of red axial muscle in the more anteriorly located ipsilateral myomeres of the caudal peduncle; at 0.75 L s(-1), only the anterior portion of the radialis and white axial muscle of the contralateral peduncular myomeres were active. Activity of the radialis muscle occurred during periods of the greatest drag incurred by the tail during the tail beat and preceded the activity of more anteriorly located axial myomeres. This nonconformity to the typical anterior to posterior wave of muscle activation in fish swimming, in combination with anatomical positioning of the radialis muscles and stratum compactum, suggests that radialis activity may have a postural function to stiffen the fin, and does not function as a typical myotomal muscle.

How does ocean seasonality drive habitat preferences of highly mobile top predators? Part I: The north-western Mediterranean Sea

NASA Astrophysics Data System (ADS)

Lambert, C.; Laran, S.; David, L.; Dorémus, G.; Pettex, E.; Van Canneyt, O.; Ridoux, V.

2017-07-01

Contrasting to the overall oligotrophic Mediterranean Sea, the north-western basin is characterised by high productivity and marked by seasonality, which induces spatiotemporal heterogeneity of habitat. Cetaceans and seabirds are expected to perceive this repetition of the seasonal cycle and to anticipate the recurrent variability of their environment. Because phenology imposes strong constraints over marine predators, especially through reproduction, we expected them to exhibit variations in their habitat preferences over seasons. Indeed, during reproductive period, marine predators have to face their own needs and those of their young, while out of this period, they can focus on maximising their own survival only. We therefore hypothesised that some species would change their habitat preferences to exploit the most favourable habitat during each season, while other species might accommodate the same habitat all year-round, for example thanks to the use of an habitat favourable all the year. To explore these hypotheses, we used aerial surveys data conducted over north-western Mediterranean Sea during winter 2011-2012 and summer 2012. Generalised Additive Models were used to link the species density to a set of 12 physiographic and oceanographic predictors describing their environment. Habitat models resulted in deviances from 12 to 47%. Our results provided the first assessment of habitat preferences for the winter season for most of our studied species. Small-sized delphinids (mostly stripped dolphins), fin whales, Globicephalinae (long-finned pilot whales and Risso's dolphins) and small-sized shearwaters (Yelkouan and Balearic shearwaters) exhibited no habitat variations between seasons, although for the first two, abundances were lower in winter. On the contrary, bottlenose dolphins switched from coastal habitat in summer to pelagic habitat in winter, while Cory's shearwaters and storm petrels exhibited the largest habitat variations between seasons with a complete absence during winter.

Composite stabilizer unit

DOEpatents

Ebaugh, Larry R.; Sadler, Collin P.; Carter, Gary D.

1992-01-01

An improved fin stabilized projectile including multiple stabilizer fins upon a stabilizer unit situated at the aft end of the projectile is provided, the improvement wherein the stabilizer fins are joined into the stabillizer unit by an injection molded engineering grade polymer.

Potassium Rankine cycle vapor chamber (heat pipe) radiator study

NASA Technical Reports Server (NTRS)

Gerrels, E. E.; Killen, R. E.

1971-01-01

A structurally integrated vapor chamber fin (heat pipe) radiator is defined and evaluated as a potential candidate for rejecting waste heat from the potassium Rankine cycle powerplant. Several vapor chamber fin geometries, using stainless steel construction, are evaluated and an optimum is selected. A comparison is made with an operationally equivalent conduction fin radiator. Both radiators employ NaK-78 in the primary coolant loop. In addition, the Vapor Chamber Fin (VCF) radiator utilizes sodium in the vapor chambers. Preliminary designs are developed for the conduction fin and VCF concepts. Performance tests on a single vapor chamber were conducted to verify the VCF design. A comparison shows the conduction fin radiator easier to fabricate, but heavier in weight, particularly as meteoroid protection requirements become more stringent. While the analysis was performed assuming the potassium Rankine cycle powerplant, the results are equally applicable to any system radiating heat to space in the 900 to 1400 F temperature range.

Low-Power and High-Speed Technique for logic Gates in 20nm Double-Gate FinFET Technology

NASA Astrophysics Data System (ADS)

Priydarshi, A.; Chattopadhyay, M. K.

2016-10-01

The FinFET is the leading example of multigate MOSFETS to substitute conventional single gate MOSFETs for ultimate scaling [1], The FinFET structure is a combination of a thin channel region and a double gate to suppress the short channel effects (SCEs) and Vthvariation [2], By using FinFET,figure of merits viz, ION, IOFF, output resistance, propagation delay, noise margin and leakage power, can be improved for ultra low power and high performance applications[3]. In this paper, a new high speed low power dynamic circuit design technique has been proposed using 20nm FinFETs. By applying the appropriate clock and sleep signal to the back gates of the FinFETs, the proposed circuit can efficiently control the dynamic power, During the pre-charging period, Vth of PMOS is controlled low so that a fast precharging can occur;

Flame-spreading phenomena in the fin-slot region of a solid rocket motor

NASA Astrophysics Data System (ADS)

Kuo, K. K.; Kokal, R. A.; Paulauskas, M.; Alaksin, P.; Lee, L. S.

1993-06-01

Flame-spreading processes in the fin-slot regions of solid-propellant motor grains have the potential to influence the behavior of the overall ignition transient. The work being done on this project is aimed at obtaining a better understanding of the flame-spreading processes in rocket motors with aft-end fin slots. Non-intrusive optical diagnostic methods were employed to acquire flame-spreading measurements in the fin-slot region of a subscale rocket motor. Highly non-uniform flame-spreading processes were observed in both the deep and shallow fin regions of the test rig. The average flame-spreading rates in the fin-slot region were found to be two orders of magnitude less than those in the circular port region of a typical rocket motor. The flame-spreading interval was found to correlate well with the local pressurization rates. A higher pressurization rate produces a shorter flame-spreading time interval.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abate, G.L.; Winchenbach, G.L.

Subsonic and transonic aerodynamic data for missiles with solid and slotted wrap around fin configurations are presented. Free-flight aeroballistic tests to obtain this data were conducted at atmospheric pressure over a Mach number range of 0.8 to 1.6. The aerodynamic coefficients and derivatives presented were extracted from the position-attitude-time histories of the experimentally measured trajectories using non-linear numerical integration data reduction routines. Results of this testing and analysis show the static and dynamic stability variations for solid and slotted wrap around fin configurations. The presence of a side moment dependent on pitch angle, inherent to wrap around fin configurations, ismore » measured for both configurations. Results indicate a reduction in the magnitude of this side-moment for missiles with slotted fins. Also, roll dependence with Mach number effects are not present with the slotted fin configurations. Designers should consider these factors whenever wrap around fins are utilized. 14 refs.« less

Experimental studies of Savonius wind turbines with variations sizes and fin numbers towards performance

NASA Astrophysics Data System (ADS)

Utomo, Ilham Satrio; Tjahjana, Dominicus Danardono Dwi Prija; Hadi, Syamsul

2018-02-01

The use of renewable energy in Indonesia is still low. Especially the use of wind energy. Wind turbine Savonius is one turbine that can work with low wind speed. However, Savonius wind turbines still have low efficiency. Therefore it is necessary to modify. Modifications by using the fin are expected to increase the positive drag force by creating a flow that can enter the overlap ratio of the gap. This research was conducted using experimental approach scheme. Parameters generated from the experiment include: power generator, power coefficient, torque coefficient. The experimental data will be collected by variation of fin area, horizontal finning, at wind speed 3 m/s - 4,85 m/s. Experimental results show that with the addition of fin can improve the performance of wind turbine Savonius 11%, and by using the diameter of 115 mm fin is able to provide maximum performance in wind turbine Savonius.

Determination of optimum fin profile for a zero-G capillary drained condenser

NASA Technical Reports Server (NTRS)

Mccormick, John A.; Valenzuela, Javier A.; Choudhury, Dipanker

1990-01-01

This paper presents the analytical formulation and numerical results for heat transfer in a high heat flux condenser that relies on capillary flow along shaped fins (Gregorig surfaces) and a drainage network embedded in the condenser walls. Results are shown for a variety of fin profile shapes in order to show the geometric trade-offs involved in seeking a maximum effective heat transfer coefficient for the fin. Predictions of the model show excellent agreement with previously reported measurements for steam. Based on this work, a profile has been selected for a 2 kW ammonia condenser currently under development for use in space. In that design the fin half width is 0.5 mm and the model predicts a heat transfer coefficient referred to the base of the fin of 9 W/sq cm deg C for a heat flux of 10/W sq cm at the base.

Microgravity condensing heat exchanger

NASA Technical Reports Server (NTRS)

Thomas, Christopher M. (Inventor); Ma, Yonghui (Inventor); North, Andrew (Inventor); Weislogel, Mark M. (Inventor)

2011-01-01

A heat exchanger having a plurality of heat exchanging aluminum fins with hydrophilic condensing surfaces which are stacked and clamped between two cold plates. The cold plates are aligned radially along a plane extending through the axis of a cylindrical duct and hold the stacked and clamped portions of the heat exchanging fins along the axis of the cylindrical duct. The fins extend outwardly from the clamped portions along approximately radial planes. The spacing between fins is symmetric about the cold plates, and are somewhat more closely spaced as the angle they make with the cold plates approaches 90.degree.. Passageways extend through the fins between vertex spaces which provide capillary storage and communicate with passageways formed in the stacked and clamped portions of the fins, which communicate with water drains connected to a pump externally to the duct. Water with no entrained air is drawn from the capillary spaces.

Experimental Study of Heat Transfer Enhancements from Array of Alternate Rectangular Dwarf Fins at Different Inclinations

NASA Astrophysics Data System (ADS)

Awasarmol, Umesh Vandeorao; Pise, Ashok T.

2018-02-01

The main objective of this experimental work is to investigate and compare heat transfer enhancement of alternate dwarf fin array at different angles of inclination. In this study, the steady state heat transfer from the full length fin arrays and alternate dwarf fin arrays are measured in natural convection and radiation environment. Largest increase in the Nusselt number was achieved with alternate dwarf fin at angle of orientation 90°, which shows about 28% enhanced heat transfer coefficient as opposed to the full-length fin array with 25% saving in material. In case of non-black FAB, contribution of radiation heat transfer is found to be very small nearly within 1% of the heater input. After coating lamp black contribution of radiation heat transfer is found to increase to about 3-4% of the heater input in the range of temperatures considered in this study.

Gobiesox lanceolatus, a new species of clingfish (Teleostei:  Gobiesocidae) from Los Frailes submarine canyon, Gulf of California, Mexico.

PubMed

Hastings, Philip A; Conway, Kevin W

2017-01-17

Gobiesox lanceolatus is described from a single specimen collected from 300 meters depth in the Los Frailes submarine canyon in the southwestern Gulf of California. The "Canyon Clingfish" is unique within Gobiesox in having a lanceolate caudal fin, with the central rays longer than those above and below them. It is also distinguished by 14 dorsal-fin rays (first tiny and unsegmented), 11 anal-fin rays, 28 pectoral-fin rays, anus slightly closer to anal-fin origin than to posterior margin of pelvic disc, and dorsal-fin origin in front of vertical from anus. It is most similar to Gobiesox eugrammus, known from Isla Guadelupe, the coast of outer Baja California and southern California. This is the deepest record for a species of Gobiesox and only four other species of clingfishes are known from greater depths.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blankenship, H.Lee; Thompson, Dan; United States. Bonneville Power Administration. Division of Fish and Wildlife

The first year of work with development of lasers as a mass marking technique provided both disappointing and encouraging results. A Coumarin Dye 480 laser was used to mark coho salmon in a variety of body locations and with varying energy levels. A ``bleached`` white mark was made void of any pigment. Areas marked included the nape area behind the head and in front of the dorsal fin, slightly above the anal fin, the upper lobe of the caudal fin, the dorsal fin and on the operculum. The mark appeared immediately after being lasered but started to gradually fade aftermore » one month and was fairly completely re-pigmented after three months. Complete removal and notching of the adipose fin was also attempted with a Carbon Dioxide laser. This surgical method of fin removal appears to have advantages over scissor excision (no bleeding or regeneration), and has possible application as part of a device or system which could be employed for mass marking.« less

Effects of 17β-trenbolone on Eastern and Western mosquitofish (Gambusia holbrooki and G. affinis) anal fin growth and gene expression patterns.

PubMed

Brockmeier, Erica K; Ogino, Yukiko; Iguchi, Taisen; Barber, David S; Denslow, Nancy D

2013-03-15

The Eastern and Western mosquitofish (Gambusia holbrooki and G. affinis) are potential bioindicator organisms for endocrine disruptors. Male mosquitofish have an elongated anal fin (gonopodium) used for internal fertilization whose formation is driven by androgens. Normal female mosquitofish have a normal, rounded anal fin which undergoes elongation into a gonopodium structure when female mosquitofish are exposed to androgenic chemicals. Significant issues with using mosquitofish as a bioindicator include the lack of knowledge on how anal fin growth in females corresponds to endpoints relevant to biological integrity and the lack of information on the molecular pathways that regulate anal fin growth. The objectives of this study were to understand how androgen-induced anal fin elongation relates to changes in endpoints related to the female reproductive system and to understand how anal fin elongation occurs in androgen-exposed female mosquitofish. To achieve these objectives, adult female G. holbrooki were exposed to a vehicle control or one of three doses of the androgen 17β-trenbolone (TB) at nominal concentrations of 0.1, 1 or 10 μg TB/L. Anal fin measurements were taken and livers were used for quantitative polymerase chain reaction analysis of vitellogenin (vtg) mRNA expression at multiple time points. 10 μg TB/L induced anal fin elongation after 7 days of treatment (one-way ANOVA, p<0.05) as did 0.1 and 1 μg TB/L at later time points (one-way ANOVA, p<0.05). 10 μg TB/L significantly reduced hepatic vtg gene expression at all time points assessed (one-way ANOVA, p<0.05). There was no correlation between anal fin elongation levels and vtg gene expression (Spearman's ρ, p>0.05). In a separate experiment, female G. holbrooki and G. affinis were exposed to the vehicle control or 1 μg TB/L. Anal fins were used for qualitative gene expression analysis of the genes sonic hedgehog (shh), muscle segment homeobox C (msxC), and fibroblast growth factor receptor 1 (fgfr1) by in situ hybridization. Shh was expressed in the distal tip of the gonopodium while msxC and fgfr1 were more widely expressed along the same anal fin rays during androgen exposure. These data provide insight into the molecular pathways involved in anal fin elongation and pave the way for future work toward developing the mosquitofish into a bioindicator organism for endocrine disruptors. Copyright © 2012 Elsevier B.V. All rights reserved.

Volumetric PIV of multiple free-swimming maneuvers generated by the KnifeBot: a biomimetic vessel propelled by an undulating fin

NASA Astrophysics Data System (ADS)

Liu, Hanlin; Troolin, Daniel; Hortensius, Ruben; Pothos, Stamatios; Curet, Oscar

2017-11-01

An undulating fin represents a remarkable propulsion model for underwater vehicles due to its high propulsive efficiency and considerable locomotor capabilities. In this work, we used a bio-inspired vessel, the KnifeBot to demonstrate the maneuverability of undulating fin propulsion, including forward-backward swimming, station keeping and vertical swimming. This self-contained robotic system uses an undulating ventral fin as the propulsor and features a slender 3D-printed hull with 16 motors, 2 batteries and electronic boards encapsulated inside. We tested the robot in a water-filled tank and used volumetric particle image velocimetry (V3V PIV) to investigate the three-dimensional flow features and vortex structures generated by the undulating ribbon fin in free-swimming maneuvers. Our results indicate that in the forward swimming, a series of vortex tubes are shed off the fin edge. A streamwise jet at an oblique angle to the fin is generated in association with the vortex tubes propelling the robot forward as well as pitching it up. For the hovering maneuver with inward counter-propagating waves. The streamlines develop vertically downward with the tip vortex shed from the fin edge. This downward jet provides substantial heave force for the robot to swim upward or perform station keeping. Our findings will be useful for understanding the mechanical basis of undulating fin propulsion and facilitate the development of bio-inspired vehicles using undulatory propellers. Office of Naval Research under Award Number N00014-16-1-2505.

Measuring family needs of people living with cancer. Portuguese validation and descriptive studies of the Family Inventory of Needs.

PubMed

Areia, Neide P; Major, Sofia; Relvas, Ana P

2017-10-01

The aim of this study was to validate the Portuguese version of the Family Inventory of Needs (FIN). The FIN aims to measure important family needs and their fulfilment by a healthcare team. This cross-sectional study involved a sample of 364 family members of cancer patients, recruited from three medical institutions and through online recruitment. Three instruments were used: a socio-demographic questionnaire, the FIN and the Brief Symptom Inventory - 18 (BSI-18). Construct validity and reliability were considered regarding the FIN's psychometric properties. The method used to determine construct validity was factor structure analysis (confirmatory factor analysis), inter-factor correlations (Spearman's rank correlation) and convergent validity (Spearman's rank correlation). To assess scale reliability, the FIN's internal consistency was evaluated (Cronbach's alpha coefficient). Descriptive and frequency statistics and tests to compare means were used to assess important needs and to what extent they were met. The four-factor structure of the FIN was confirmed. Thus, the FIN has four domains: Basic Information, Information on treatment and care, Support and Patient Comfort. Convergent validity with the BSI-18 was verified. Both subscales of the FIN and each domain exceeded the minimum reliability standard of 0.70. Family members also reported important needs that were not adequately met by healthcare professionals. The Portuguese version of the FIN seems to be a reliable and valid tool for identifying cancer patients' important family needs and to what extent these are met. Copyright © 2017 Elsevier Ltd. All rights reserved.

F-16 Ventral Fin Buffet Alleviation Using Piezoelectric Actuators

DTIC Science & Technology

2009-09-01

collocated design to alleviate the vibrations of the first two modes of the ventral fin. A switching amplifier was de - signed and custom built to drive the...6M per year [22]. 1 Figure 1.1: LANTIRN Pod and Ventral Fin Locations [cour- tesy USAF] Buffet induced vibrations affect more than just vertical tail...appropriate sensors and actuators for the ventral fin. Several de - viations were necessary, including individual actuator size and orientation and the

Heat-transfer coefficients for air flowing in round tubes, in rectangular ducts, and around finned cylinders

NASA Technical Reports Server (NTRS)

Drexel, Rober E; Mcadams, William H

1945-01-01

Report reviews published data and presents some new data on heat transfer to air flowing in round tubes, in rectangular ducts, and around finned cylinders. The available data for heat transfer to air in straight ducts of rectangular and circular cross section have been correlated in plots of Stanton number versus Reynolds number to provide a background for the study of the data for finned cylinders. Equations are recommended for both the streamlined and turbulent regions, and data are presented for the transition region between turbulent and laminar flow. Use of hexagonal ends on round tubes causes the characteristics of laminar flow to extend to high Reynolds numbers. Average coefficients for the entire finned cylinder have been calculated from the average temperature at the base of the fins and an equation which was derived to allow for the effectiveness of the fins. The available results for each finned cylinder are correlated herein in terms of graphs of Stanton number versus Reynolds number. In general, for a given Reynolds number, the Stanton number increases with increases in both spacing and width of the fins, and is apparently independent of cylinder diameter and temperature difference. For a given coefficient of heat transfer improved baffles and rough or wavy surfaces give a substantial reduction in pumping power per unit of heat transfer surface and a somewhat smaller decrease in pressure drop. (author)

A new basal galeomorph shark (Synechodontiformes, Neoselachii) from the Early Jurassic of Europe

NASA Astrophysics Data System (ADS)

Klug, Stefanie; Kriwet, Jürgen

2008-05-01

Palaeospinacids are a group of basal galeomorph sharks and are placed in the order Synechodontiformes (Chondrichthyes, Neoselachii) ranging from the Permian to the Eocene. Currently, there is a controversy concerning the identity of diagnostic characters for distinguishing palaeospinacid genera because of very similar dental morphologies and the scarcity of articulated skeletal material. The most notable character for distinguishing species within the Palaeospinacidae is, however, the dental morphology. The main dental character uniting all palaeospinacids is the very specialised pseudopolyaulacorhize root vascularisation. A re-examination of articulated neoselachian skeletons from the Lower Jurassic of Lyme Regis (England) and Holzmaden (S Germany), and recently discovered specimens from the Upper Jurassic of the Solnhofen area and Nusplingen (S Germany) has yielded several hitherto unrecognised complete skeletons of the palaeospinacids Synechodus and Paraorthacodus enabling a re-evaluation of characters. These specimens indicate that the number of dorsal fins and the presence or absence of dorsal fin spines represent important features for identifying palaeospinacids. Synechodus bears two dorsal fins without fin spines, whereas Paraorthacodus only has a single dorsal fin lacking a fin spine directly in front of the caudal fin. All palaeospinacids from the Early Jurassic have two spines supporting the dorsal fins and are consequently assigned to a new genus, Palidiplospinax nov. gen. Three species are placed into the new taxon: Synechodus enniskilleni, S. occultidens and S. smithwoodwardi.

Ice nucleating particles measured during the laboratory and field intercomparisons FIN-2 and FIN-3 by the diffusion chamber FRIDGE

NASA Astrophysics Data System (ADS)

Weber, Daniel; Schrod, Jann; Curtius, Joachim; Haunold, Werner; Thomson, Erik; Bingemer, Heinz

2016-04-01

The measurement of atmospheric ice nucleating particles (INP) is still challenging. In the absence of easily applicable INP standards the intercomparison of different methods during collaborative laboratory and field workshops is a valuable tool that can shine light on the performance of individual methods for the measurement of INP [1]. FIN-2 was conducted in March 2015 at the AIDA facility in Karlsruhe as an intercomparison of mobile instruments for measuring INP [2]. FIN-3 was a field campaign at the Desert Research Institutes Storm Peak Laboratory in Colorado in September 2015 [3]. The FRankfurt Ice nucleation Deposition freezinG Experiment (FRIDGE) participated in both experiments. FRIDGE measures ice nucleating particles by electrostatic precipitation of aerosol particles onto Si-wafers in a collection unit, followed by activation, growth, and optical detection of ice crystals on the substrate in an isostatic diffusion chamber [4,5]. We will present and discuss results of our measurements of deposition/condensation INP and of immersion INP with FRIDGE during FIN-2 and FIN-3. Acknowledgements: The valuable contributions of the FIN organizers and their institutions, and of the FIN Workshop Science team are gratefully acknowledged. Our work was supported by Deutsche Forschungsgemeinschaft (DFG) under the Research Unit FOR 1525 (INUIT) and the EU FP7-ENV- 2013 BACCHUS project under Grant Agreement 603445.

Precision and accuracy of age estimates obtained from anal fin spines, dorsal fin spines, and sagittal otoliths for known-age largemouth bass

USGS Publications Warehouse

Klein, Zachary B.; Bonvechio, Timothy F.; Bowen, Bryant R.; Quist, Michael C.

2017-01-01

Sagittal otoliths are the preferred aging structure for Micropterus spp. (black basses) in North America because of the accurate and precise results produced. Typically, fisheries managers are hesitant to use lethal aging techniques (e.g., otoliths) to age rare species, trophy-size fish, or when sampling in small impoundments where populations are small. Therefore, we sought to evaluate the precision and accuracy of 2 non-lethal aging structures (i.e., anal fin spines, dorsal fin spines) in comparison to that of sagittal otoliths from known-age Micropterus salmoides (Largemouth Bass; n = 87) collected from the Ocmulgee Public Fishing Area, GA. Sagittal otoliths exhibited the highest concordance with true ages of all structures evaluated (coefficient of variation = 1.2; percent agreement = 91.9). Similarly, the low coefficient of variation (0.0) and high between-reader agreement (100%) indicate that age estimates obtained from sagittal otoliths were the most precise. Relatively high agreement between readers for anal fin spines (84%) and dorsal fin spines (81%) suggested the structures were relatively precise. However, age estimates from anal fin spines and dorsal fin spines exhibited low concordance with true ages. Although use of sagittal otoliths is a lethal technique, this method will likely remain the standard for aging Largemouth Bass and other similar black bass species.

Embryonic development of fin spines in Callorhinchus milii (Holocephali); implications for chondrichthyan fin spine evolution.

PubMed

Jerve, Anna; Johanson, Zerina; Ahlberg, Per; Boisvert, Catherine

2014-01-01

Fin spines are commonly known from fossil gnathostomes (jawed vertebrates) and are usually associated with paired and unpaired fins. They are less common among extant gnathostomes, being restricted to the median fins of certain chondrichthyans (cartilaginous fish), including chimaerids (elephant sharks) and neoselachians (sharks, skates, and rays). Fin spine growth is of great interest and relevance but few studies have considered their evolution and development. We investigated the development of the fin spine of the chimaerid Callorhinchus milii using stained histological sections from a series of larval, hatchling, and adult individuals. The lamellar trunk dentine of the Callorhinchus spine first condenses within the mesenchyme, rather than at the contact surface between mesenchyme and epithelium, in a manner more comparable to dermal bone formation than to normal odontode development. Trabecular dentine forms a small component of the spine under the keel; it is covered externally with a thin layer of lamellar trunk dentine, which is difficult to distinguish in sectioned adult spines. We suggest that the distinctive characteristics of the trunk dentine may reflect an origin through co-option of developmental processes involved in dermal bone formation. Comparison with extant Squalus and a range of fossil chondrichthyans shows that Callorhinchus is more representative than Squalus of generalized chondrichthyan fin-spine architecture, highlighting its value as a developmental model organism. © 2014 Wiley Periodicals, Inc.

The Oldest Actinopterygian Highlights the Cryptic Early History of the Hyperdiverse Ray-Finned Fishes.

PubMed

Lu, Jing; Giles, Sam; Friedman, Matt; den Blaauwen, Jan L; Zhu, Min

2016-06-20

Osteichthyans comprise two divisions, each containing over 32,000 living species [1]: Sarcopterygii (lobe-finned fishes and tetrapods) and Actinopterygii (ray-finned fishes). Recent discoveries from China highlight the morphological disparity of early sarcopterygians and extend their origin into the late Silurian [2-4]. By contrast, the oldest unambiguous actinopterygians are roughly 30 million years younger, leaving a long temporal gap populated by fragments and rare body fossils of controversial phylogenetic placement [5-10]. Here we reinvestigate the enigmatic osteichthyan Meemannia from the Early Devonian (∼415 million years ago) of China, previously identified as an exceptionally primitive lobe-finned fish [3, 7, 11, 12]. Meemannia combines "cosmine"-like tissues taken as evidence of sarcopterygian affinity with actinopterygian-like skull roof and braincase geometry, including endoskeletal enclosure of the spiracle and a lateral cranial canal. We report comparable histological structures in undoubted ray-finned fishes and conclude that they are general osteichthyan features. Phylogenetic analysis places Meemannia as an early-diverging ray-finned fish, resolving it as the sister lineage of Cheirolepis [13] plus all younger actinopterygians. This brings the first appearance of ray-fins more in line with that of lobe-fins and fills a conspicuous faunal gap in the otherwise diverse late Silurian-earliest Devonian vertebrate faunas of the South China Block [4]. Copyright © 2016 The Author(s). Published by Elsevier Ltd.. All rights reserved.

A novel trapezoid fin pattern applicable for air-cooled heat sink

NASA Astrophysics Data System (ADS)

Chen, Chien-Hung; Wang, Chi-Chuan

2015-11-01

The present study proposed a novel step or trapezoid surface design applicable to air-cooled heat sink under cross flow condition. A total of five heat sinks were made and tested, and the corresponding fin patterns are (a) plate fin; (b) step fin (step 1/3, 3 steps); (c) 2-step fin (step 1/2, 2 steps); (d) trapezoid fin (trap 1/3, cutting 1/3 length from the rear end) and (e) trapezoid fin (trap 1/2, cutting 1/2 length from the rear end). The design is based on the heat transfer augmentation via (1) longer perimeter of entrance region and (2) larger effective temperature difference at the rear part of the heat sink. From the test results, it is found that either step or trapezoid design can provide a higher heat transfer conductance and a lower pressure drop at a specified frontal velocity. The effective conductance of trap 1/3 design exceeds that of plate surface by approximately 38 % at a frontal velocity of 5 m s-1 while retains a lower pressure drop of 20 % with its surface area being reduced by 20.6 %. For comparisons exploiting the overall thermal resistance versus pumping power, the resultant thermal resistance of the proposed trapezoid design 1/3, still reveals a 10 % lower thermal resistance than the plate fin surface at a specified pumping power.

Heat transfer and pressure drop characteristics of the tube bank fin heat exchanger with fin punched with flow redistributors and curved triangular vortex generators

NASA Astrophysics Data System (ADS)

Liu, Song; Jin, Hua; Song, KeWei; Wang, LiangChen; Wu, Xiang; Wang, LiangBi

2017-10-01

The heat transfer performance of the tube bank fin heat exchanger is limited by the air-side thermal resistance. Thus, enhancing the air-side heat transfer is an effective method to improve the performance of the heat exchanger. A new fin pattern with flow redistributors and curved triangular vortex generators is experimentally studied in this paper. The effects of the flow redistributors located in front of the tube stagnation point and the curved vortex generators located around the tube on the characteristics of heat transfer and pressure drop are discussed in detail. A performance comparison is also carried out between the fins with and without flow redistributors. The experimental results show that the flow redistributors stamped out from the fin in front of the tube stagnation points can decrease the friction factor at the cost of decreasing the heat transfer performance. Whether the combination of the flow redistributors and the curved vortex generators will present a better heat transfer performance depends on the size of the curved vortex generators. As for the studied two sizes of vortex generators, the heat transfer performance is promoted by the flow redistributors for the fin with larger size of vortex generators and the performance is suppressed by the flow redistributors for the fin with smaller vortex generators.

The Fifth International Ice Nucleation Workshop Activities FIN-1 and FIN-2: Overview and Selected Results

NASA Astrophysics Data System (ADS)

Moehler, O.; Cziczo, D. J.; DeMott, P. J.; Hiranuma, N.; Petters, M. D.

2015-12-01

The role of aerosol particles for ice formation in clouds is one of the largest uncertainties in understanding the Earth's weather and climate systems, which is related to the poor knowledge of ice nucleation microphysics or of the nature and atmospheric abundance of ice nucleating particles (INPs). During the recent years, new mobile instruments were developed for measuring the concentration, size and chemical composition of INPs, which were tested during the three-part Fifth International Ice Nucleation (FIN) workshop. The FIN activities addressed not only instrument issues, but also important science topics like the nature of atmospheric INP and cloud ice residuals, the ice nucleation activity of relevant atmospheric aerosols, or the parameterization of ice formation in atmospheric weather and climate models. The first activity FIN-1 was conducted during November 2014 at the AIDA cloud chamber. It involved co-locating nine single particle mass spectrometers to evaluate how well they resolve the INP and ice residual composition and how spectra from different instruments compare for relevant atmospheric aerosols. We conducted about 90 experiments with mineral, carbonaceous and biological aerosol types, some also coated with organic and inorganic compounds. The second activity FIN-2 was conducted during March 2015 at the AIDA facility. A total of nine mobile INP instruments directly sampled from the AIDA aerosol chambers. Wet suspension and filter samples were also taken for offline INP processing. A refereed blind intercomparison was conducted during two days of the FIN-2 activity. The third activity FIN-3 will take place at the Desert Research Institute's Storm Peak Laboratory (SPL) in order to test the instruments' performance in the field. This contribution will introduce the FIN activities, summarize first results from the formal part of FIN-2, and discuss selected results, mainly from FIN-1 for the effect of coating on the ice nucleation (IN) by mineral aerosols. The coating with both secondary organic compounds and sulphuric acid was conducted in the AIDA chamber at relevant temperatures and precursor concentrations and was monitored with the particle mass spectrometers. Already very thin, atmospherically relevant coatings reduced deposition IN, but had little effect on immersion freezing.

Water flow and fin shape polymorphism in coral reef fishes.

PubMed

Binning, Sandra A; Roche, Dominique G

2015-03-01

Water flow gradients have been linked to phenotypic differences and swimming performance across a variety of fish assemblages. However, the extent to which water motion shapes patterns of phenotypic divergence within species remains unknown. We tested the generality of the functional relationship between swimming morphology and water flow by exploring the extent of fin and body shape polymorphism in 12 widespread species from three families (Acanthuridae, Labridae, Pomacentridae) of pectoral-fin swimming (labriform) fishes living across localized wave exposure gradients. The pectoral fin shape of Labridae and Acanthuridae species was strongly related to wave exposure: individuals with more tapered, higher aspect ratio (AR) fins were found on windward reef crests, whereas individuals with rounder, lower AR fins were found on leeward, sheltered reefs. Three of seven Pomacentridae species showed similar trends, and pectoral fin shape was also strongly related to wave exposure in pomacentrids when fin aspect ratios of three species were compared across flow habitats at very small spatial scales (<100 m) along a reef profile (reef slope, crest, and back lagoon). Unlike fin shape, there were no intraspecific differences in fish body fineless ratio across habitats or depths. Contrary to our predictions, there was no pattern relating species' abundances to polymorphism across habitats (i.e., abundance was not higher at sites where morphology is better adapted to the environment). This suggests that there are behavioral and/or physiological mechanisms enabling some species to persist across flow habitats in the absence of morphological differences. We suggest that functional relationships between swimming morphology and water flow not only structure species assemblages, but are yet another important variable contributing to phenotypic differences within species. The close links between fin shape polymorphism and local water flow conditions appear to be important for understanding species' distributions as well as patterns of diversification across environmental gradients.

Developmental structure of the vertebral column, fins, scutes and scales in bester sturgeon, a hybrid of beluga Huso huso and sterlet Acipenser ruthenus.

PubMed

Zhang, X; Shimoda, K; Ura, K; Adachi, S; Takagi, Y

2012-11-01

In the larval bester, a hybrid sturgeon of beluga Huso huso and sterlet Acipenser ruthenus, development of cartilage around the notochord began 7 days post hatch (dph) (14.0 mm, total length, L(T)). The vertebral cartilage develops in the following sequence: basidorsals and basiventrals, neural canals, neural spines and ribs. The development of ribs remained incomplete in the largest specimen (181 dph, 179 mm L(T) ) that was examined. Endoskeletal development of the fins began 4 dph for the dorsal and anal fins, 6 dph for the pectoral fin and 10 dph for the caudal and pelvic fins. Complete elements of all fins were observed by 91 dph and complete ossification of fin rays was observed by 122 dph in the double-stained specimens. Observation of the histological sections, however, suggested that ossification occurred soon after the formation of the organic matrix in the fin rays. Dorsal scutes were first visible by 25 dph, followed by the lateral and ventral scutes, which were visible by 37 and 44 dph, respectively. The number of scutes was fixed at 44, 59 and 91 dph and ossification was complete by 59 (dorsal) and 91 dph (lateral and ventral scutes) in the double-stained specimens. Ossification occurred soon after the formation of the scute organic matrix in the histological sections. Four types of scales were observed in the H. huso×A. ruthenus hybrid. Median predorsal, preanal and small scales on the anterior section of the head were visible by 59 dph. Scales on the caudal fin were visible by 91 dph and a variable assemblage of scales anterior to the anal fin was visible by 122 dph. Both the scutes and scales developed in a process that is similar to that of intramembranous ossification. © 2012 The Authors. Journal of Fish Biology © 2012 The Fisheries Society of the British Isles.

Performance ‘S’ Type Savonius Wind Turbine with Variation of Fin Addition on Blade

NASA Astrophysics Data System (ADS)

Pamungkas, S. F.; Wijayanto, D. S.; Saputro, H.; Widiastuti, I.

2018-01-01

Wind power has been receiving attention as the new energy resource in addressing the ecological problems of burning fossil fuels. Savonius wind rotor is a vertical axis wind turbines (VAWT) which has relatively simple structure and low operating speed. These characteristics make it suitable for areas with low average wind speed as in Indonesia. To identify the performance of Savonius rotor in generating electrical energy, this research experimentally studied the effect of fin addition for the ‘S’ shape of Savonius VAWT. The fin is added to fill the space in the blade in directing the wind flow. This rotor has two turbine blades, a rotor diameter of 1.1 m and rotor height of 1.4 m, used pulley transmission system with 1:4.2 multiplication ratio, and used a generator type PMG 200 W. The research was conducted during dry season by measuring the wind speed in the afternoon. The average wind speed in the area is 2.3 m/s with the maximum of 4.5 m/s. It was found that additional fin significantly increase the ability of Savonius rotor VAWT to generate electrical energy shown by increasing of electrical power. The highest power generated is 13.40 Watt at a wind speed of 4.5 m/s by adding 1 (one) fin in the blade. It increased by 22.71% from the rotor blade with no additional fin. However, increasing number of fins in the blade was not linearly increase the electrical power generated. The wind rotor blade with 4 additional fins is indicated has the lowest performance, generating only 10.80 Watt electrical power, accounted lower than the one generated by no fin-rotor blade. By knowing the effect of the rotor shape, the rotor dimension, the addition of fin, transmission, and generator used, it is possible to determine alternative geometry design in increasing the electrical power generated by Savonius wind turbine.

Fish biorobotics: kinematics and hydrodynamics of self-propulsion.

PubMed

Lauder, George V; Anderson, Erik J; Tangorra, James; Madden, Peter G A

2007-08-01

As a result of years of research on the comparative biomechanics and physiology of moving through water, biologists and engineers have made considerable progress in understanding how animals moving underwater use their muscles to power movement, in describing body and appendage motion during propulsion, and in conducting experimental and computational analyses of fluid movement and attendant forces. But it is clear that substantial future progress in understanding aquatic propulsion will require new lines of attack. Recent years have seen the advent of one such new avenue that promises to greatly broaden the scope of intellectual opportunity available to researchers: the use of biorobotic models. In this paper we discuss, using aquatic propulsion in fishes as our focal example, how using robotic models can lead to new insights in the study of aquatic propulsion. We use two examples: (1) pectoral fin function, and (2) hydrodynamic interactions between dorsal and caudal fins. Pectoral fin function is characterized by considerable deformation of individual fin rays, as well as spanwise (along the length) and chordwise (across the fin) deformation and area change. The pectoral fin can generate thrust on both the outstroke and instroke. A robotic model of the pectoral fin replicates this result, and demonstrates the effect of altering stroke kinematics on the pattern of force production. The soft dorsal fin of fishes sheds a distinct vortex wake that dramatically alters incoming flow to the tail: the dorsal fin and caudal fin act as dual flapping foils in series. This design can be replicated with a dual-foil flapping robotic device that demonstrates this phenomenon and allows examination of regions of the flapping performance space not available to fishes. We show how the robotic flapping foil device can also be used to better understand the significance of flexible propulsive surfaces for locomotor performance. Finally we emphasize the utility of self-propelled robotic devices as a means of understanding how locomotor forces are generated, and review different conceptual designs for robotic models of aquatic propulsion.

The fish fauna of Anambra river basin, Nigeria: species abundance and morphometry.

PubMed

Odo, Gregory Ejikeme; Didigwu, Nwani Christopher; Eyo, Joseph Effiong

2009-01-01

The fish yields of most Nigeria inland waters are generally on the decline for causes that may range from inadequate management of the fisheries to degradation of the water bodies. Sustainable exploitation requires knowledge of the ichthyofaunal composition in the water bodies. We did a survey of fish species in Anambra river basin for 22 months. Fish samples were collected using four different gears -hook and line of size 13, caste nets, gill nets, and cages of mesh sizes of 50 mm, 75 mm, and 100 mm each. We recorded 52 fish species belonging to 17 families: 171, 236, and 169 individuals at Ogurugu, Otuocha, and Nsugbe stations respectively. Two families, Characidae, 19.5%, and Mochokidae, 11.8%, constituted the dominant fish families in the river. The dominant fish species were Citherinus citherius, 9.02%, and Alestes nurse, 7.1%. Other fish species with significant abundance were Synodontis clarias 6.9%, Macrolepidotus curvier 5.7%, Labeo coubie 5.4%, Distichodus rostrtus 4.9%, and Schilbe mystus 4.5%. The meristic features of the two most abundant fish species caught are as follows: Citharinus citharius dorsal fins 20, anal fins 30, caudal fins 21, pectoral fins, 9 and 8 ventral fins, and Alestes nurse 10 dorsal fins, 14 anal fins, 31 caudal fins, 7 pectoral fins and 6 ventral fins. The morphometric features of the two most abundant fish species are Citharinus citharius total length 300 mm, standard length 231 mm, head length 69 mm, body length 101 mm, body girth 176 mm, body weight 900 mg. Alestes nurse total length 200, standard length 140 mm, head length 60 mm, body length 80 mm, body girth 120 mm, body weight 400 mg. The most abundant animal utilizing the basin was Ardea cinerea (D3) with 22.2% occurrence (D4) and this was followed by Caprini with 13.51%, and Varanus niloticus, 10.04%. The least abundant animals utilizing basin were Chephalophus rufilatus, and Erythrocebus patas, with 0.58% each of occurrence.

Utilizing Chemo-mechanically Functionalized Oscillating Fins to ``Catch and Release'' Nanoparticles in Binary Flow

NASA Astrophysics Data System (ADS)

Liu, Ya; Kuksenok, Olga; Bhattacharya, Amitabh; Ma, Yongting; He, Ximin; Aizenberg4, Joanna; Balazs, Anna

2014-03-01

In biomimetics, designing an effective ``catch and release'' device for the selective removal of target species from the surrounding solution is critical for developing autonomous sensors and sorters. Using computer simulations, we model an array of oscillating fins that are tethered on the floor of a microchannel and immersed in a mixture of binary fluid stream and binary nanoparticles. During the oscillation, the fins with the specific chemical wetting reach the upper fluid when they are upright and are entirely immersed within the lower stream when they are tilted. We introduce specific interaction between the fins and particulates in the solution and determine conditions where the oscillating fins can selectively ?catch? target nanoparticles within the upper fluid stream and then release these particles into the lower stream. We isolate the effects of wetting contact angle between fins and fluid and the mode of fins' oscillations that lead to the efficient extraction of target species from the upper stream and their placement into the lower fluid. These studies provide fundamental insights into the system's complex dynamics and mechanism for detection, separation, and purification of multi-component mixtures.

Effect of pectoral fin kinematics on manta ray propulsion

NASA Astrophysics Data System (ADS)

Lu, Hao; Yeo, Khoon Seng; Chew, Chee-Meng

2018-05-01

Recent advancement of bio-inspired underwater vehicles has led to a growing interest in understanding the fluid mechanics of fish locomotion, which involves complex interaction between the deforming structure and its surrounding fluid. Unlike most natural swimmers that undulate their body and caudal fin, manta rays employ an oscillatory mode by flapping their large, flattened pectoral fins to swim forward. Such a lift-based mode can achieve a substantially high propulsive efficiency, which is beneficial to long-distance swimming. In this study, numerical simulations are carried out on a realistic manta ray model to investigate the effect of pectoral fin kinematics on the propulsive performance and flow structure. A traveling wave model, which relates a local deflection angle to radial and azimuthal wavelengths, is applied to generate the motion of the pectoral fins. Hydrodynamic forces and propulsive efficiency are reported for systematically varying kinematic parameters such as wave amplitude and wavelengths. Key flow features, including a leading edge vortex (LEV) that forms close to the tip of each pectoral fin, and a wake consisting of interconnected vortex rings, are identified. In addition, how different fin motions alter the LEV behavior and hence affect the thrust and efficiency is illustrated.

Slotting Fins of Heat Exchangers to Provide Thermal Breaks

NASA Technical Reports Server (NTRS)

Scull, Timothy D.

2003-01-01

Heat exchangers that include slotted fins (in contradistinction to continuous fins) have been invented. The slotting of the fins provides thermal breaks that reduce thermal conduction along flow paths (longitudinal thermal conduction), which reduces heat-transfer efficiency. By increasing the ratio between transverse thermal conduction (the desired heat-transfer conduction) and longitudinal thermal conduction, slotting of the fins can be exploited to (1) increase heat-transfer efficiency (thereby reducing operating cost) for a given heat-exchanger length or to (2) reduce the length (thereby reducing the weight and/or cost) of the heat exchanger needed to obtain a given heat transfer efficiency. By reducing the length of a heat exchanger, one can reduce the pressure drop associated with the flow through it. In a case in which slotting enables the use of fins with thermal conductivity greater than could otherwise be tolerated on the basis of longitudinal thermal conduction, one can exploit the conductivity to make the fins longer (in the transverse direction) than they otherwise could be, thereby making it possible to make a heat exchanger that contains fewer channels and therefore, that weighs less, contains fewer potential leak paths, and can be constructed from fewer parts and, hence, reduced cost.

Study of 3D-growth conditions for selective area MOVPE of high aspect ratio GaN fins with non-polar vertical sidewalls

NASA Astrophysics Data System (ADS)

Hartmann, Jana; Steib, Frederik; Zhou, Hao; Ledig, Johannes; Nicolai, Lars; Fündling, Sönke; Schimpke, Tilman; Avramescu, Adrian; Varghese, Tansen; Trampert, Achim; Straßburg, Martin; Lugauer, Hans-Jürgen; Wehmann, Hergo-Heinrich; Waag, Andreas

2017-10-01

GaN fins are 3D architectures elongated in one direction parallel to the substrate surface. They have the geometry of walls with a large height to width ratio as well as small footprints. When appropriate symmetry directions of the GaN buffer are used, the sidewalls are formed by non-polar {1 1 -2 0} planes, making the fins particularly suitable for many device applications like LEDs, FETs, lasers, sensors or waveguides. The influence of growth parameters like temperature, pressure, V/III ratio and total precursor flow on the fin structures is analyzed. Based on these results, a 2-temperature-step-growth was developed, leading to fins with smooth side and top facets, fast vertical growth rates and good homogeneity along their length as well as over different mask patterns. For the core-shell growth of fin LED heterostructures, the 2-temperature-step-growth shows much smoother sidewalls and less crystal defects in the InGaN QW and p-GaN shell compared to structures with cores grown in just one step. Electroluminescence spectra of the 2-temperature-step-grown fin LED are demonstrated.

Effect of Tube Diameter on The Design of Heat Exchanger in Solar Drying system

NASA Astrophysics Data System (ADS)

Husham Abdulmalek, Shaymaa; Khalaji Assadi, Morteza; Al-Kayiem, Hussain H.; Gitan, Ali Ahmed

2018-03-01

The drying of agriculture product consumes a huge fossil fuel rates that demand to find an alternative source of sustainable environmental friendly energy such as solar energy. This work presents the difference between using solar heat source and electrical heater in terms of design aspect. A circular-finned tube bank heat exchanger is considered against an electrical heater used as a heat generator to regenerate silica gel in solar assisted desiccant drying system. The impact of tube diameter on the heat transfer area was investigated for both the heat exchanger and the electrical heater. The fin performance was investigated by determining fin effectiveness and fin efficiency. A mathematical model was developed using MATLAB to describe the forced convection heat transfer between hot water supplied by evacuated solar collector with 70 °C and ambient air flow over heat exchanger finned tubes. The results revealed that the increasing of tube diameter augments the heat transfer area of both heat exchanger and electrical heater. The highest of fin efficiency was around 0.745 and the lowest was around 0.687 while the fin effectiveness was found to be around 0.998.

Electrochemical behavior of tube-fin assembly for an aluminum automotive condenser with improved corrosion resistance

NASA Astrophysics Data System (ADS)

Pech-Canul, M. A.; Guía-Tello, J. C.; Pech-Canul, M. I.; Aguilar, J. C.; Gorocica-Díaz, J. A.; Arana-Guillén, R.; Puch-Bleis, J.

An aluminum automotive condenser was designed to exhibit high corrosion resistance in the seawater acetic acid test (SWAAT) combining zinc coated microchannel tubes and fins made with AA4343/AA3003(Zn)/AA4343 brazing sheet. Electrochemical measurements in SWAAT solution were carried out under laboratory conditions using tube-fin assembly and individual fin and tube samples withdrawn from the condenser core. The aim was to gain information on the protective role of the zinc sacrificial layer and about changes in corrosion behavior as a function of immersion time. External corrosion of the tube-fin system was simulated by immersion of mini-core samples under open circuit conditions. The corrosion rate increased rapidly during the first 6 h and slowly afterwards. The short time behavior was related to the dissolution of the oxide film and fast dissolution of the outermost part of the zinc diffusion layer. With the aid of cross-sectional depth corrosion potential profiles, it was shown that as the sacrificial layer gets dissolved, the surface concentration of zinc decreases and the potential shifts to less negative values. The results of galvanic coupling of tube and fins in a mini-cell showed that the tube became the anode while the fins exhibited cathodic behavior. An evolution in the galvanic interaction was observed, due to the progressive dissolution of the sacrificial zinc layer. The difference of uncoupled potentials between tube and fins decreased from 71 mV to 32 mV after 84 h of galvanic coupling. At the end of such period there was still a part of the zinc sacrificial layer remaining which would serve for protection of the tube material for even longer periods and there were indications of slight corrosion in the fins.

Hydrodynamics of a robotic fish tail: effects of the caudal peduncle, fin ray motions and the flow speed.

PubMed

Ren, Ziyu; Yang, Xingbang; Wang, Tianmiao; Wen, Li

2016-02-08

Recent advances in understanding fish locomotion with robotic devices have included the use of biomimetic flapping based and fin undulatory locomotion based robots, treating two locomotions separately from each other. However, in most fish species, patterns of active movements of fins occur in concert with the body undulatory deformation during swimming. In this paper, we describe a biomimetic robotic caudal fin programmed with individually actuated fin rays to mimic the fin motion of the Bluegill Sunfish (Lepomis macrochirus) and coupled with heave and pitch oscillatory motions adding to the robot to mimic the peduncle motion which is derived from the undulatory fish body. Multiple-axis force and digital particle image velocimetry (DPIV) experiments from both the vertical and horizontal planes behind the robotic model were conducted under different motion programs and flow speeds. We found that both mean thrust and lift could be altered by changing the phase difference (φ) from 0° to 360° between the robotic caudal peduncle and the fin ray motion (spanning from 3 mN to 124 mN). Notably, DPIV results demonstrated that the caudal fin generated multiple wake flow patterns in both the vertical and horizontal planes by varying φ. Vortex jet angle and thrust impulse also varied significantly both in these two planes. In addition, the vortex shedding position along the spanwise tail direction could be shifted around the mid-sagittal position between the upper and lower lobes by changing the phase difference. We hypothesize that the fish caudal fin may serve as a flexible vectoring propeller during swimming and may be critical for the high maneuverability of fish.

Wind Fins: Novel Lower-Cost Wind Power System

DOE Office of Scientific and Technical Information (OSTI.GOV)

David C. Morris; Dr. Will D. Swearingen

This project evaluated the technical feasibility of converting energy from the wind with a novel “wind fin” approach. This patent-pending technology has three major components: (1) a mast, (2) a vertical, hinged wind structure or fin, and (3) a power takeoff system. The wing structure responds to the wind with an oscillating motion, generating power. The overall project goal was to determine the basic technical feasibility of the wind fin technology. Specific objectives were the following: (1) to determine the wind energy-conversion performance of the wind fin and the degree to which its performance could be enhanced through basic designmore » improvements; (2) to determine how best to design the wind fin system to survive extreme winds; (3) to determine the cost-effectiveness of the best wind fin designs compared to state-of-the-art wind turbines; and (4) to develop conclusions about the overall technical feasibility of the wind fin system. Project work involved extensive computer modeling, wind-tunnel testing with small models, and testing of bench-scale models in a wind tunnel and outdoors in the wind. This project determined that the wind fin approach is technically feasible and likely to be commercially viable. Project results suggest that this new technology has the potential to harvest wind energy at approximately half the system cost of wind turbines in the 10kW range. Overall, the project demonstrated that the wind fin technology has the potential to increase the economic viability of small wind-power generation. In addition, it has the potential to eliminate lethality to birds and bats, overcome public objections to the aesthetics of wind-power machines, and significantly expand wind-power’s contribution to the national energy supply.« less

The incidence of bent dorsal fins in free-ranging cetaceans.

PubMed

Alves, F; Towers, J R; Baird, R W; Bearzi, G; Bonizzoni, S; Ferreira, R; Halicka, Z; Alessandrini, A; Kopelman, A H; Yzoard, C; Rasmussen, M H; Bertulli, C G; Jourdain, E; Gullan, A; Rocha, D; Hupman, K; Mrusczok, M-T; Samarra, F I P; Magalhães, S; Weir, C R; Ford, J K B; Dinis, A

2018-02-01

Laterally bent dorsal fins are rarely observed in free-ranging populations of cetaceans, contrary to captivity, where most killer whale Orcinus orca adult males have laterally collapsed fins. This topic has been poorly explored, and data/information on its occurrence and possible causes are limited. The present study: (i) undertakes a review of the available information on bent dorsal fins in free-ranging cetaceans, and updates it with new records, (ii) reports on the proportion of bent fins in different study populations, and (iii) discusses possible causes. An empirical approach based on bibliographic research and compilation of 52 new records collected worldwide resulted in a total of 17 species of cetaceans displaying bent dorsal fins. The species with the highest number of records (64%) and from most locations was O. orca. On average, individuals with bent dorsal fins represent < 1% of their populations, with the exception of false killer whales Pseudorca crassidens and O. orca. While line injuries associated with fisheries interactions may be the main cause for P. crassidens, and the vulnerability to health issues caused by the evolutionary enlargement of the fin may be the cause for O. orca adult males, factors contributing to this abnormality for other species are still unclear. The occurrence of bent dorsals could be influenced by a set of variables rather than by a single factor but, irrespective of the cause, it is suggested that it does not directly affect the animals' survivorship. While still rare in nature, this incident is more common (at least 101 known cases) and widespread (geographically and in species diversity) than hypothesized, and is not confined only to animals in captive environments. Investigation into the occurrence of bent fins may be an interesting avenue of research. © 2017 Anatomical Society.

The heartstrings mutation in zebrafish causes heart/fin Tbx5 deficiency syndrome.

PubMed

Garrity, Deborah M; Childs, Sarah; Fishman, Mark C

2002-10-01

Holt-Oram syndrome is one of the autosomal dominant human "heart-hand" disorders, with a combination of upper limb malformations and cardiac defects. Holt-Oram syndrome is caused by mutations in the TBX5 gene, a member of a large family of T-box transcription factors that play important roles in cell-type specification and morphogenesis. In a screen for mutations affecting zebrafish cardiac function, we isolated the recessive lethal mutant heartstrings, which lacks pectoral fins and exhibits severe cardiac dysfunction, beginning with a slow heart rate and progressing to a stretched, non-functional heart. We mapped and cloned the heartstrings mutation and find it to encode the zebrafish ortholog of the TBX5 gene. The heartstrings mutation causes premature termination at amino acid 316. Homozygous mutant embryos never develop pectoral fin buds and do not express several markers of early fin differentiation. The total absence of any fin bud differentiation distinguishes heartstrings from most other mutations that affect zebrafish fin development, suggesting that Tbx5 functions very early in the pectoral fin induction pathway. Moderate reduction of Tbx5 by morpholino causes fin malformations, revealing an additional early requirement for Tbx5 in coordinating the axes of fin outgrowth. The heart of heartstrings mutant embryos appears to form and function normally through the early heart tube stage, manifesting only a slight bradycardia compared with wild-type siblings. However, the heart fails to loop and then progressively deteriorates, a process affecting the ventricle as well as the atrium. Relative to mammals, fish require lower levels of Tbx5 to produce malformed appendages and display whole-heart rather than atrial-predominant cardiac defects. However, the syndromic deficiencies of tbx5 mutation are remarkably well retained between fish and mammals.

Stability Characteristics of Two Missiles of Fineness Ratios 12 and 18 with Six Rectangular Fins of Very Low Aspect Ratio Over a Mach Number Range of 1.4 to 3.2

NASA Technical Reports Server (NTRS)

Henning, Allen B.

1959-01-01

Two rocket-propelled missiles have been test flown by the Langley Pilotless Aircraft Research Division in order to study the stability characteristics of a body with six rectangular fins of very low aspect ratio. The fins, which had exposed aspect ratios of approximately o.o4 and 0.02 per fin, were mounted on bodies of fineness ratios of 12 and 18, respectively. Each body had a nose with a fineness ratio of 3.5 and a cylindrical afterbody. The body and the fin chord of the model having a fineness ratio of 12 were extended the length of 6 body diameters to produce the model with a fineness ratio of 18. The missiles were disturbed in flight by pulse rockets in order to obtain the stability data. The tests were performed over a Mach number range of 1.4 to 3.2 and a Reynolds number range of 2 x 10(exp 6) to 21 x l0(exp 6). The results of these tests indicate that these configurations with the long rectangular fins of very low aspect ratio showed little induced roll" with the missile of highest fineness ratio and longest fin chord exhibiting the least amount. Extending the body and fin chord of the shorter missile six body diameters and thereby increasing the fin area approximately 115 percent increased the lift-curve slope based on body cross-sectional area approximately 40 to 55 percent, increased the dynamic stability by a substantial amount, and increased the drag from 14 to 33 percent throughout the comparable Mach number range. The center-of-pressure location of both missiles remained constant over the Mach number range.

Sexual Dimorphism and Geographic Variation in Dorsal Fin Features of Australian Humpback Dolphins, Sousa sahulensis.

PubMed

Brown, Alexander M; Bejder, Lars; Parra, Guido J; Cagnazzi, Daniele; Hunt, Tim; Smith, Jennifer L; Allen, Simon J

2016-01-01

Determining the sex of free-ranging cetaceans can be challenging. Sexual dimorphism among external features may allow inferences on sex, but such patterns may be difficult to detect and are often confounded by age and geographic variation. Dorsal fin images of 107 female and 54 male Australian humpback dolphins, Sousa sahulensis, from Western Australia (WA) and Queensland (QLD) were used to investigate sex, age and geographic differences in colouration, height/length quotient and number of notches. Adult males exhibited more dorsal fin notches (p<0.001) and a significantly greater loss of pigmentation on the upper half of their dorsal fins (p<0.001) than did adult females. These differences likely reflect that males experience a higher frequency and/or intensity of intraspecific aggression than females. In QLD, heavily spotted dorsal fins were more frequent among females than males (p<0.001). Logistic regression analyses revealed that dorsal fin spotting and loss of pigmentation on the upper half of the dorsal fin provided the best model parameters for predicting the sex of sampled adults, with 97% accuracy. This technique offers a rapid, non-invasive method for predicting sex in Australian humpback dolphins, which could potentially be applied to populations throughout their range. In contrast to adults, presumed immature animals showed little or no loss of pigmentation or spotting; however, the rate of development of these features remains unknown. There were pronounced differences between QLD and WA in the intensity of spotting on dorsal fins and the extent of pigmentation loss around the posterior insertion and trailing edge of the dorsal fin. While based on a limited sample size, these geographic differences may have conservation implications in terms of population subdivision and should be investigated further. © 2016 Elsevier Ltd. All rights reserved.

Magnetoresistance measurement of permalloy thin film rings with triangular fins

NASA Astrophysics Data System (ADS)

Lai, Mei-Feng; Hsu, Chia-Jung; Liao, Chun-Neng; Chen, Ying-Jiun; Wei, Zung-Hang

2010-01-01

Magnetization reversals in permalloy rings controlled by nucleation sites using triangular fins at the same side and diagonal with respect to the field direction are demonstrated by magnetoresistance measurement and micromagnetic simulation. In the ring with triangular fins at the same side, there exists two-step reversal from onion to flux-closure state (or vortex state) and then from flux-closure (or vortex state) to reverse onion state; in the ring with diagonal triangular fins, one-step reversal occurs directly from onion to reverse onion state. The reversal processes are repeatable and controllable in contrast to an ideal ring without triangular fins where one-step and two-step reversals occur randomly in sweep-up and sweep-down processes.

Development and Application of Collaborative Optimization Software for Plate - fin Heat Exchanger

NASA Astrophysics Data System (ADS)

Chunzhen, Qiao; Ze, Zhang; Jiangfeng, Guo; Jian, Zhang

2017-12-01

This paper introduces the design ideas of the calculation software and application examples for plate - fin heat exchangers. Because of the large calculation quantity in the process of designing and optimizing heat exchangers, we used Visual Basic 6.0 as a software development carrier to design a basic calculation software to reduce the calculation quantity. Its design condition is plate - fin heat exchanger which was designed according to the boiler tail flue gas. The basis of the software is the traditional design method of the plate-fin heat exchanger. Using the software for design and calculation of plate-fin heat exchangers, discovery will effectively reduce the amount of computation, and similar to traditional methods, have a high value.

The X-38 V-201 Fin Fold Actuation Mechanism

NASA Technical Reports Server (NTRS)

Lupo, Christian; Robertson, Brandan; Gafka, George

2004-01-01

The X-38 Vehicle 201 (V-201) is a space flight prototype lifting body vehicle that was designed to launch to orbit in the Space Shuttle orbiter payload bay. Although the project was cancelled in May 2003, many of the systems were nearly complete. This paper will describe the fin folding actuation mechanism flight subsystems and development units as well as lessons learned in the design, assembly, development testing, and qualification testing. The two vertical tail fins must be stowed (folded inboard) to allow the orbiter payload bay doors to close. The fin folding actuation mechanism is a remotely or extravehicular activity (EVA) actuated single fault tolerant system consisting of seven subsystems capable of repeatedly deploying or stowing the fins.

Aerodynamic characteristics of cruciform missiles at high angles of attack

NASA Technical Reports Server (NTRS)

Lesieutre, Daniel J.; Mendenhall, Michael R.; Nazario, Susana M.; Hemsch, Michael J.

1987-01-01

An aerodynamic prediction method for missile aerodynamic performance and preliminary design has been developed to utilize a newly available systematic fin data base and an improved equivalent angle of attack methodology. The method predicts total aerodynamic loads and individual fin forces and moments for body-tail (wing-body) and canard-body-tail configurations with cruciform fin arrangements. The data base and the prediction method are valid for angles of attack up to 45 deg, arbitrary roll angles, fin deflection angles between -40 deg and 40 deg, Mach numbers between 0.6 and 4.5, and fin aspect ratios between 0.25 and 4.0. The equivalent angle of attack concept is employed to include the effects of vorticity and geometric scaling.

Role of fin material and nanofluid in performance enhancement of automobile radiator

NASA Astrophysics Data System (ADS)

Jadar, Raju; Shashishekar, K. S.; Channa Keshava Naik, N.

2018-04-01

An effective cooling system can avoid engine and its components from overheating and helps in achieving optimum engine performance. This work deals with the fabrication and performance evaluation of an automobile radiator with i) Aluminum fins and ii) Al-MWCNT fins using 0.1 w/v% f-MWCNT nanofluid. F-MWCNT nanoparticles in the base fluid improves the rate of heat transfer in an automobile radiator integrated with Al-MWCNT fins. The enhancement of heat transfer mainly depends on the quantity of F-MWCNT nanoparticles added to the host fluid. During the study it was found that at a low weight by volume concentration of nanofluid the heat transfer enhancement of 8% was achieved using Al-MWCNT fins compared to base fluid.

Hydrodynamical analysis of the effect of fish fins morphology

NASA Astrophysics Data System (ADS)

Azwadi Che Sidik, Nor; Yen, Tey Wah

2013-12-01

The previous works on the biomechanics of fishes focuses on the locomotion effect of the fish bodies. However, there is quite a insufficiency in unveiling the respective function of fins when the fishes pose statics and exposed to fluid flow. Accordingly, this paper's focus is to investigate the hydrodynamic effect of the fins configuration to the fluid flow of shark-shaped-inspired structure. The drag and lift coefficient is computed for different cases of fish fins addition and configuration. The k-epsilon turbulence model is deployed using finite volume method with the aid of commercial software ANSYS CFX. The finding will demystify some of the functions of the fish's fins in term of their contribution to the hydrodynamic flow around the fishes.

An experimental study of three-dimensional shock wave/boundary layer interactions generated by sharp fins

NASA Technical Reports Server (NTRS)

Lu, F. K.; Settles, G. S.; Bogdonoff, S. M.

1983-01-01

The interaction between a turbulent boundary layer and a shock wave generated by a sharp fin with leading edge sweepback was investigated. The incoming flow was at Mach 2.96 and at a unit Reynolds number of 63 x 10 to the 6th power 0.1 m. The approximate incoming boundary layer thickness was either 4 mm or 17 mm. The fins used were at 5 deg, 9 deg and 15 deg incidence and had leading edge sweepback from 0 deg to 65 deg. The tests consisted of surface kerosene lampblack streak visualization, surface pressure measurements, shock wave shape determination by shadowgraphs, and localized vapor screen visualization. The upstream influence lengths of the fin interactions were correlated using viscous and inviscid flow parameters. The parameters affecting the surface features close to the fin and way from the fin were also identified. Essentially, the surface features in the farfield were found to be conical.

The fin-to-limb transition as the re-organization of a Turing pattern

PubMed Central

Onimaru, Koh; Marcon, Luciano; Musy, Marco; Tanaka, Mikiko; Sharpe, James

2016-01-01

A Turing mechanism implemented by BMP, SOX9 and WNT has been proposed to control mouse digit patterning. However, its generality and contribution to the morphological diversity of fins and limbs has not been explored. Here we provide evidence that the skeletal patterning of the catshark Scyliorhinus canicula pectoral fin is likely driven by a deeply conserved Bmp–Sox9–Wnt Turing network. In catshark fins, the distal nodular elements arise from a periodic spot pattern of Sox9 expression, in contrast to the stripe pattern in mouse digit patterning. However, our computer model shows that the Bmp–Sox9–Wnt network with altered spatial modulation can explain the Sox9 expression in catshark fins. Finally, experimental perturbation of Bmp or Wnt signalling in catshark embryos produces skeletal alterations which match in silico predictions. Together, our results suggest that the broad morphological diversity of the distal fin and limb elements arose from the spatial re-organization of a deeply conserved Turing mechanism. PMID:27211489

A new Species of Hemibrycon (Characiformes, Characidae, Stevardiinae) from the upper Magdalena River basin in Colombia.

PubMed

García-Melo, J E; Albornoz-Garzón, J G; García-Melo, L J; Villa-Navarro, F A; Maldonado-Ocampo, J A

2018-04-16

Hemibrycon iqueima sp. nov., is described from small streams in the Magdalena drainage at the foothills of the western slope of the Eastern Cordillera of the Colombian Andes, Suarez municipality, Tolima Department, Colombia. The new species is distinguished from its congeners in the Magdalena-Cauca River basin by a combination of characters related to snout-anal-fin origin length, head length, dorsal-pectoral fin distance, dorsal-fin-hypural distance, postorbital distance, orbital diameter, snout length, number of total vertebrae, pre-dorsal scales, scale rows between anal-fin origin and lateral line, number of branched rays of the anal fin, maxillary teeth number and number and arrangement of hooks on the branched rays of the pectoral and dorsal fins. In addition, the validity of this species is supported by previous molecular analyses that included specimens of the new species that had been erroneously identified. Phylogenetic relationships between the new species and congeners from Pacific coast basins are discussed. This article is protected by copyright. All rights reserved.

Bio-inspired flexible joints with passive feathering for robotic fish pectoral fins.

PubMed

Behbahani, Sanaz Bazaz; Tan, Xiaobo

2016-05-04

In this paper a novel flexible joint is proposed for robotic fish pectoral fins, which enables a swimming behavior emulating the fin motions of many aquatic animals. In particular, the pectoral fin operates primarily in the rowing mode, while undergoing passive feathering during the recovery stroke to reduce hydrodynamic drag on the fin. The latter enables effective locomotion even with symmetric base actuation during power and recovery strokes. A dynamic model is developed to facilitate the understanding and design of the joint, where blade element theory is used to calculate the hydrodynamic forces on the pectoral fins, and the joint is modeled as a paired torsion spring and damper. Experimental results on a robotic fish prototype are presented to illustrate the effectiveness of the joint mechanism, validate the proposed model, and indicate the utility of the proposed model for the optimal design of joint depth and stiffness in achieving the trade-off between swimming speed and mechanical efficiency.

Fluid flow and heat transfer characteristics of an enclosure with fin as a top cover of a solar collector

NASA Astrophysics Data System (ADS)

Ambarita, H.; Ronowikarto, A. D.; Siregar, R. E. T.; Setyawan, E. Y.

2018-03-01

To reduce heat loses in a flat plate solar collector, double glasses cover is employed. Several studies show that the heat loss from the glass cover is still very significant in comparison with other losses. Here, double glasses cover with attached fins is proposed. In the present work, the fluid flow and heat transfer characteristics of the enclosure between the double glass cover are investigated numerically. The objective is to examine the effect of the fin to the heat transfer rate of the cover. Two-dimensional governing equations are developed. The governing equations and the boundary conditions are solved using commercial Computational Fluid Dynamics code. The fluid flow and heat transfer characteristics are plotted, and numerical results are compared with empirical correlation. The results show that the presence of the fin strongly affects the fluid flow and heat transfer characteristics. The fin can reduce the heat transfer rate up to 22.42% in comparison with double glasses cover without fins.

Temperature dependency of double material gate oxide (DMGO) symmetric dual-k spacer (SDS) wavy FinFET

NASA Astrophysics Data System (ADS)

Pradhan, K. P.; Priyanka; Sahu, P. K.

2016-01-01

Symmetric Dual-k Spacer (SDS) Trigate Wavy FinFET is a novel hybrid device that combines three significant and advanced technologies i.e., ultra-thin-body (UTB), FinFET, and symmetric spacer engineering on a single silicon on insulator (SOI) platform. This innovative architecture promises to enhance the device performance as compared to conventional FinFET without increasing the chip area. For the first time, we have incorporated two different dielectric materials (SiO2, and HfO2) as gate oxide to analyze the effect on various performance metrics of SDS wavy FinFET. This work evaluates the response of double material gate oxide (DMGO) on parameters like mobility, on current (Ion), transconductance (gm), transconductance generation factor (TGF), total gate capacitance (Cgg), and cutoff frequency (fT) in SDS wavy FinFET. This work also reveals the presence of biasing point i.e., zero temperature coefficient (ZTC) bias point. The ZTC bias point is that point where the device parameters become independent of temperature. The impact of operating temperature (T) on above said various performances are also subjected to extensive analysis. This further validates the reliability of DMGO-SDS FinFET and its application opportunities involved in modeling analog/RF circuits for a broad range of temperature applications. From extensive 3-D device simulation, we have determined that the inclusion of DMGO in SDS wavy FinFET is superior in performance.

Inhibition of caudal fin regeneration in Corydoras aeneus by lithium chloride.

PubMed

Zarnescu, Otilia; Stavri, Simona; Moldovan, Lucia

2013-03-01

In the present study we examined the effects of lithium chloride on the Corydoras aeneus caudal fin regeneration. After caudal fin amputation, the fish were exposed 3h daily to 35 mM lithium chloride for 9 days. The effects of lithium chloride treatment were evaluated by analyzing the caudal fin structure at 3, 6 and 9 days after amputation. Comparison of normal and LiCl treated fish clearly shows that regeneration of amputated caudal fins was inhibited or delayed after lithium treatment. By the third day after amputation (dpa) either no epidermal cap or blastema ever formed or the epidermal cap had an abnormal morphology in lithium treated fish. By the 3 and 6 dpa no lepidotrichial matrix deposition was observed in the lithium treated fish compared to control fish. Unlike the control fish that completely regenerate their caudal fins after 9 dpa and have fully mineralized lepidotrichia, lithium treated fish have small blastema. In some treated fish, small amounts of new lepidotrichial matrix were observed at this time, in some fin rays. Ultrastructural observations have shown differences between control and lithium treated fish. Thus, in the lithium treated fish we observed expanded intercellular spaces between epidermal cells and many apoptotic cells. Results of this study suggest the use of this model in elucidating the molecular mechanisms that are responsible for regeneration of complex structures such as fish fins. Copyright © 2013 Elsevier Ltd. All rights reserved.

Phenotypic variation in dorsal fin morphology of coastal bottlenose dolphins (Tursiops truncatus) off Mexico

PubMed Central

Rocha-Olivares, Axayácatl; Morteo, Rodrigo; Weller, David W.

2017-01-01

Geographic variation in external morphology is thought to reflect an interplay between genotype and the environment. Morphological variation has been well-described for a number of cetacean species, including the bottlenose dolphin (Tursiops truncatus). In this study we analyzed dorsal fin morphometric variation in coastal bottlenose dolphins to search for geographic patterns at different spatial scales. A total of 533 dorsal fin images from 19 available photo-identification catalogs across the three Mexican oceanic regions (Pacific Ocean n = 6, Gulf of California n = 6 and, Gulf of Mexico n = 7) were used in the analysis. Eleven fin shape measurements were analyzed to evaluate fin polymorphism through multivariate tests. Principal Component Analysis on log-transformed standardized ratios explained 94% of the variance. Canonical Discriminant Function Analysis on factor scores showed separation among most study areas (p < 0.05) with exception of the Gulf of Mexico where a strong morphometric cline was found. Possible explanations for the observed differences are related to environmental, biological and evolutionary processes. Shape distinction between dorsal fins from the Pacific and those from the Gulf of California were consistent with previously reported differences in skull morphometrics and genetics. Although the functional advantages of dorsal fin shape remains to be assessed, it is not unlikely that over a wide range of environments, fin shape may represent a trade-off among thermoregulatory capacity, hydrodynamic performance and the swimming/hunting behavior of the species. PMID:28626607

3D modeling of dual-gate FinFET.

PubMed

Mil'shtein, Samson; Devarakonda, Lalitha; Zanchi, Brian; Palma, John

2012-11-13

The tendency to have better control of the flow of electrons in a channel of field-effect transistors (FETs) did lead to the design of two gates in junction field-effect transistors, field plates in a variety of metal semiconductor field-effect transistors and high electron mobility transistors, and finally a gate wrapping around three sides of a narrow fin-shaped channel in a FinFET. With the enhanced control, performance trends of all FETs are still challenged by carrier mobility dependence on the strengths of the electrical field along the channel. However, in cases when the ratio of FinFET volume to its surface dramatically decreases, one should carefully consider the surface boundary conditions of the device. Moreover, the inherent non-planar nature of a FinFET demands 3D modeling for accurate analysis of the device performance. Using the Silvaco modeling tool with quantization effects, we modeled a physical FinFET described in the work of Hisamoto et al. (IEEE Tran. Elec. Devices 47:12, 2000) in 3D. We compared it with a 2D model of the same device. We demonstrated that 3D modeling produces more accurate results. As 3D modeling results came close to experimental measurements, we made the next step of the study by designing a dual-gate FinFET biased at Vg1 >Vg2. It is shown that the dual-gate FinFET carries higher transconductance than the single-gate device.

3D modeling of dual-gate FinFET

NASA Astrophysics Data System (ADS)

Mil'shtein, Samson; Devarakonda, Lalitha; Zanchi, Brian; Palma, John

2012-11-01

The tendency to have better control of the flow of electrons in a channel of field-effect transistors (FETs) did lead to the design of two gates in junction field-effect transistors, field plates in a variety of metal semiconductor field-effect transistors and high electron mobility transistors, and finally a gate wrapping around three sides of a narrow fin-shaped channel in a FinFET. With the enhanced control, performance trends of all FETs are still challenged by carrier mobility dependence on the strengths of the electrical field along the channel. However, in cases when the ratio of FinFET volume to its surface dramatically decreases, one should carefully consider the surface boundary conditions of the device. Moreover, the inherent non-planar nature of a FinFET demands 3D modeling for accurate analysis of the device performance. Using the Silvaco modeling tool with quantization effects, we modeled a physical FinFET described in the work of Hisamoto et al. (IEEE Tran. Elec. Devices 47:12, 2000) in 3D. We compared it with a 2D model of the same device. We demonstrated that 3D modeling produces more accurate results. As 3D modeling results came close to experimental measurements, we made the next step of the study by designing a dual-gate FinFET biased at V g1 > V g2. It is shown that the dual-gate FinFET carries higher transconductance than the single-gate device.

A global review of species-specific shark-fin-to-body-mass ratios and relevant legislation.

PubMed

Biery, L; Pauly, D

2012-04-01

In this review, shark-fin-to-body-mass ratios, which have been legislated by several countries as a means of regulating and monitoring shark fisheries, have been compiled and reviewed. Observed and legislated wet-fin-mass-to-round-mass (M(fw) :M(r) ) ratios have been collected for 50 species and eight countries. Wet to dry-fin mass conversion factors have also been reviewed. Existing shark fishery legislation was compiled by political entity and regional fishery management organizations (RFMO). The mean observed M(fw) :M(r) ratio for all species was 3·0%, but actual fin to body-mass ratios varied considerably by species and location. Species-specific mean ratios ranged from 1·1 to 10·9%, and estimated mean ratios ranged from 1·5 to 6·1% by country, depending on fin-cutting practices and the mix of exploited species. The mean conversion factor for wet to dry-fin mass was 0·43. Shark-related legislation was found to exist in 37 countries and the 22 maritime members of the European Union, and shark-related regulations have been designated by nine RFMOs. Results suggest that currently regulated ratios may not be appropriate for all species and fin-cutting practices, and regulations based on generalized ratios for all sharks may be inadequate. Alternative policies may be necessary for the effective management of global shark fisheries. © 2012 The Authors. Journal of Fish Biology © 2012 The Fisheries Society of the British Isles.

Mechanical design, fabrication, and test of biomimetic fish robot using LIPCA as artificial muscle

NASA Astrophysics Data System (ADS)

Wiguna, T.; Syaifuddin, M.; Park, Hoon C.; Heo, S.

2006-03-01

This paper presents a mechanical design, fabrication and test of biomimetic fish robot using the Lightweight Piezocomposite Curved Actuator (LIPCA). We have designed a mechanism for converting actuation of the LIPCA into caudal fin movement. This linkage mechanism consists of rack-pinion system and four-bar linkage. We also have tested four types of caudal fin in order to examine effect of different shape of caudal fin on thrust generation by tail beat. Subsequently, based on the caudal fin test, four caudal fins which resemble fish caudal fin shapes of ostraciiform, subcarangiform, carangiform and thunniform, respectively, are attached to the posterior part of the robotic fish. The swimming test using 300 V pp input with 1 Hz to 1.5 Hz frequency was conducted to investigate effect of changing tail beat frequency and shape of caudal fin on the swimming speed of the robotic fish. The maximum swimming speed was reached when the device was operated at its natural swimming frequency. At the natural swimming frequency 1 Hz, maximum swimming speeds of 1.632 cm/s, 1.776 cm/s, 1.612 cm/s and 1.51 cm/s were reached for ostraciiform-, subcarangiform-, carangiform- and thunniform-like caudal fins, respectively. Strouhal numbers, which are a measure of thrust efficiency, were calculated in order to examine thrust performance of the present biomimetic fish robot. We also approximated the net forward force of the robotic fish using momentum conservation principle.

Fish's Muscles Distortion and Pectoral Fins Propulsion of Lift-Based Mode

NASA Astrophysics Data System (ADS)

Yang, S. B.; Han, X. Y.; Qiu, J.

As a sort of MPF(median and/or paired fin propulsion), pectoral fins propulsion makes fish easier to maneuver than other propulsion, according to the well-established classification scheme proposed by Webb in 1984. Pectoral fins propulsion is classified into oscillatory propulsion, undulatory propulsion and compound propulsion. Pectoral fins oscillatory propulsion, is further ascribable to two modes: drag-based mode and lift-based mode. And fish exhibits strong cruise ability by using lift-based mode. Therefore to robot fish design using pectoral fins lift-based mode will bring a new revolution to resources exploration in blue sea. On the basis of the wave plate theory, a kinematic model of fish’s pectoral fins lift-based mode is established associated with the behaviors of cownose ray (Rhinoptera bonasus) in the present work. In view of the power of fish’s locomotion from muscle distortion, it would be helpful benefit to reveal the mechanism of fish’s locomotion variation dependent on muscles distortion. So this study puts forward the pattern of muscles distortion of pectoral fins according to the character of skeletons and muscles of cownose ray in morphology and simulates the kinematics of lift-based mode using nonlinear analysis software. In the symmetrical fluid field, the model is simulated left-right symmetrically or asymmetrically. The results qualitatively show how muscles distortion determines the performance of fish locomotion. Finally the efficient muscles distortion associated with the preliminary dynamics is induced.

Flap-lag-torsional dynamic modelling of rotor blades in hover and in forward flight, including the effect of cubic nonlinearities

NASA Technical Reports Server (NTRS)

Crespodasilva, M. R. M.

1981-01-01

The differential equations of motion, and boundary conditions, describing the flap-lead/lag-torsional motion of a flexible rotor blade with a precone angle and a variable pitch angle, which incorporates a pretwist, are derived via Hamilton's principle. The meaning of inextensionality is discussed. The equations are reduced to a set of three integro partial differential equations by elimination of the extension variable. The generalized aerodynamic forces are modelled using Greenberg's extension of Theodorsen's strip theory. The equations of motion are systematically expanded into polynomial nonlinearities with the objective of retaining all terms up to third degree. The blade is modeled as a long, slender, of isotropic Hookean materials. Offsets from the blade's elastic axis through its shear center and the axes for the mass, area and aerodynamic centers, radial nonuniformaties of the blade's stiffnesses and cross section properties are considered and the effect of warp of the cross section is included in the formulation.

Measurements of a Newly Designed BPM for the Tevatron Electron Lens 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scarpine, V. E.; Kamerdzhiev, V.; Fellenz, B.

2006-11-20

Fermilab has developed a second electron lens (TEL-2) for beam-beam compensation in the Tevatron as part of its Run II upgrade program. Operation of the beam position monitors (BPMs) in the first electron lens (TEL-1) showed a systematic transverse position difference between short proton bunches (2 ns sigma) and long electron pulses ({approx}1 us) of up to {approx}1.5 mm. This difference was attributed to frequency dependence in the BPM system. The TEL-2 BPMs utilize a new, compact four-plate design with grounding strips between plates to minimize crosstalk. In-situ measurements of these new BPMs are made using a stretched wire pulsedmore » with both proton and electron beam formats. In addition, longitudinal impedance measurements of the TEL-2 are presented. Signal processing algorithm studies indicate that the frequency-dependent transverse position offset may be reduced to {approx}0.1 mm for the beam structures of interest.« less

14 CFR 23.445 - Outboard fins or winglets.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Outboard fins or winglets. 23.445 Section 23.445 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... with loads induced by the fins or winglets and moments or forces exerted on the horizontal surfaces or...

14 CFR 23.445 - Outboard fins or winglets.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Outboard fins or winglets. 23.445 Section 23.445 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... with loads induced by the fins or winglets and moments or forces exerted on the horizontal surfaces or...

50 CFR 600.1203 - Prohibitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1203 Prohibitions. (a) In addition..., any of the following: (1) Engage in shark finning, as provided in § 600.1204(a) and (i). (2) Possess shark fins without the corresponding carcasses while on board a U.S. fishing vessel, as provided in...

50 CFR 600.1203 - Prohibitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1203 Prohibitions. (a) In addition..., any of the following: (1) Engage in shark finning, as provided in § 600.1204(a) and (i). (2) Possess shark fins without the corresponding carcasses while on board a U.S. fishing vessel, as provided in...

50 CFR 600.1203 - Prohibitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1203 Prohibitions. (a) In addition..., any of the following: (1) Engage in shark finning, as provided in § 600.1204(a) and (i). (2) Possess shark fins without the corresponding carcasses while on board a U.S. fishing vessel, as provided in...

50 CFR 600.1203 - Prohibitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1203 Prohibitions. (a) In addition..., any of the following: (1) Engage in shark finning, as provided in § 600.1204(a) and (i). (2) Possess shark fins without the corresponding carcasses while on board a U.S. fishing vessel, as provided in...

50 CFR 600.1203 - Prohibitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., DEPARTMENT OF COMMERCE MAGNUSON-STEVENS ACT PROVISIONS Shark Finning § 600.1203 Prohibitions. (a) In addition..., any of the following: (1) Engage in shark finning, as provided in § 600.1204(a) and (i). (2) Possess shark fins without the corresponding carcasses while on board a U.S. fishing vessel, as provided in...

Film Condensation of Steam on Externally Finned Horizontal Tubes.

DTIC Science & Technology

1985-03-01

Thermal Conductivity of Tube/Fin Metal i" ir - Condensation Rate Nu - Nusselt Number PA’ PB’ PC - Pressure at Points A, B, and C in Figure 2.1 APAB’ PcB...single finned tubes. To predict the film coefficients, they started with the Nusselt equations for condensation on a horizontal tube and on a vertical... Nusselt equation was obtained. A " condensation efficiency" was then proposed to account for a variable fin temperature, and was defined as: C, F1 (2.18) 3

Fluid-cooled heat sink with improved fin areas and efficiencies for use in cooling various devices

DOEpatents

Bharathan, Desikan; Bennion, Kevin; Kelly, Kenneth; Narumanchi, Sreekant

2015-04-21

The disclosure provides a fluid-cooled heat sink having a heat transfer base and a plurality of heat transfer fins in thermal communication with the heat transfer base, where the heat transfer base and the heat transfer fins form a central fluid channel through which a forced or free cooling fluid may flow. The heat transfer pins are arranged around the central fluid channel with a flow space provided between adjacent pins, allowing for some portion of the central fluid channel flow to divert through the flow space. The arrangement reduces the pressure drop of the flow through the fins, optimizes average heat transfer coefficients, reduces contact and fin-pin resistances, and reduces the physical footprint of the heat sink in an operating environment.

Thermal management optimization of an air-cooled Li-ion battery module using pin-fin heat sinks for hybrid electric vehicles

NASA Astrophysics Data System (ADS)

Mohammadian, Shahabeddin K.; Zhang, Yuwen

2015-01-01

Three dimensional transient thermal analysis of an air-cooled module that contains prismatic Li-ion cells next to a special kind of aluminum pin fin heat sink whose heights of pin fins increase linearly through the width of the channel in air flow direction was studied for thermal management of Lithium-ion battery pack. The effects of pin fins arrangements, discharge rates, inlet air flow velocities, and inlet air temperatures on the battery were investigated. The results showed that despite of heat sinks with uniform pin fin heights that increase the standard deviation of the temperature field, using this kind of pin fin heat sink compare to the heat sink without pin fins not only decreases the bulk temperature inside the battery, but also decreases the standard deviation of the temperature field inside the battery as well. Increasing the inlet air temperature leads to decreasing the standard deviation of the temperature field while increases the maximum temperature of the battery. Furthermore, increasing the inlet air velocity first increases the standard deviation of the temperature field till reaches to the maximum point, and after that decreases. Also, increasing the inlet air velocity leads to decrease in the maximum temperature of the battery.

Amplitude Effects on Thrust Production for Undulatory Swimmers

NASA Astrophysics Data System (ADS)

Gater, Brittany; Bayandor, Javid

2017-11-01

Biological systems offer novel and efficient solutions to many engineering applications, including marine propulsion. It is of interest to determine how fish interact with the water around them, and how best to utilize the potential their methods offer. A stingray-like fin was chosen for analysis due to the maneuverability and versatility of stingrays. The stingray fin was modeled in 2D as a sinusoidal wave with an amplitude increasing from zero at the leading edge to a maximum at the trailing edge. Using this model, a parametric study was performed to examine the effects of the fin on surrounding water in CFD simulations. The results were analyzed both qualitatively, in terms of the pressure contours on the fin and vorticity in the trailing wake, and quantitatively, in terms of the resultant forces on the fin. The amplitude was found to have no effect on the average thrust during steady swimming, when the wave speed on the fin was approximately equal to the swimming speed. However, amplitude was shown to have a significant effect on thrust production when the fin was accelerating. This finding suggests that for undulatory swimmers, amplitude is less useful for controlling swimming speed, but can be used to great effect for augmenting thrust during acceleration.

Pool boiling on surfaces with mini-fins and micro-cavities

NASA Astrophysics Data System (ADS)

Pastuszko, Robert; Piasecka, Magdalena

2012-11-01

The experimental studies presented here focused on pool boiling heat transfer on mini-fin arrays, mini-fins with perforated covering and surfaces with micro-cavities. The experiments were carried out for water and fluorinert FC-72 at atmospheric pressure. Mini-fins of 0.5 and 1 mm in height were uniformly spaced on the base surface. The copper foil with holes of 0.1 mm in diameter (pitch 0.2/0.4 mm), sintered with the fin tips, formed a system of connected perpendicular and horizontal tunnels. The micro-cavities were obtained through spark erosion. The maximal depth of the craters of these cavities was 15 - 30 μm and depended on the parameters of the branding-pen settings. At medium and small heat fluxes, structures with mini-fins showed the best boiling heat transfer performance both for water and FC-72. At medium and high heat fluxes (above 70 kW/m2 for water and 25 kW/m2 for FC-72), surfaces with mini-fins without porous covering and micro-cavities produced the highest heat transfer coefficients. The surfaces obtained with spark erosion require a proper selection of geometrical parameters for particular liquids - smaller diameters of cavities are suitable for liquids with lower surface tension (FC-72).

Supersonic aerodynamic characteristics of a circular body Earth-to-Orbit vehicle

NASA Technical Reports Server (NTRS)

Ware, George M.; Engelund, Walter C.; Macconochie, Ian O.

1994-01-01

The circular body configuration is a generic single- or multi-stage reusable Earth-to-orbit transport. A thick clipped-delta wing is the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center fin, wingtip fins, and a nose-mounted fin. The tests were conducted in the Langley Unitary Plan Wind Tunnel. The configuration is longitudinally stable about the estimated center of gravity of 0.72 body length up to a Mach number of about 3.0. Above Mach 3.0, the model is longitudinally unstable at low angles of attack but has a stable secondary trim point at angles of attack above 30 deg. The model has sufficient pitch control authority with elevator and body flap to produce stable trim over the test range. The model with the center fin is directionally stable at low angles of attack up to a Mach number of 3.90. The rudder-like surfaces on the tip fins and the all-movable nose fin are designed as active controls to produce artificial directional stability and are effective in producing yawing moment. The wing trailing-edge aileron surfaces are effective in producing rolling moment, but they also produce large adverse yawing moment.

Gene expression profiles of fin regeneration in loach (Paramisgurnus dabryanu).

PubMed

Li, Li; He, Jingya; Wang, Linlin; Chen, Weihua; Chang, Zhongjie

2017-11-01

Teleost fins can regenerate accurate position-matched structure and function after amputation. However, we still lack systematic transcriptional profiling and methodologies to understand the molecular basis of fin regeneration. After histological analysis, we established a suppression subtraction hybridization library containing 418 distinct sequences expressed differentially during the process of blastema formation and differentiation in caudal fin regeneration. Genome ontology and comparative analysis of differential distribution of our data and the reference zebrafish genome showed notable subcategories, including multi-organism processes, response to stimuli, extracellular matrix, antioxidant activity, and cell junction function. KEGG pathway analysis allowed the effective identification of relevant genes in those pathways involved in tissue morphogenesis and regeneration, including tight junction, cell adhesion molecules, mTOR and Jak-STAT signaling pathway. From relevant function subcategories and signaling pathways, 78 clones were examined for further Southern-blot hybridization. Then, 17 genes were chosen and characterized using semi-quantitative PCR. Then 4 candidate genes were identified, including F11r, Mmp9, Agr2 and one without a match to any database. After real-time quantitative PCR, the results showed obvious expression changes in different periods of caudal fin regeneration. We can assume that the 4 candidates, likely valuable genes associated with fin regeneration, deserve additional attention. Thus, our study demonstrated how to investigate the transcript profiles with an emphasis on bioinformatics intervention and how to identify potential genes related to fin regeneration processes. The results also provide a foundation or knowledge for further research into genes and molecular mechanisms of fin regeneration. Copyright © 2017 Elsevier B.V. All rights reserved.

A Middle Triassic thoracopterid from China highlights the evolutionary origin of overwater gliding in early ray-finned fishes.

PubMed

Xu, Guang-Hui; Zhao, Li-Jun; Shen, Chen-Chen

2015-01-01

Gliding adaptations in thoracopterid flying fishes represent a remarkable case of convergent evolution of overwater gliding strategy with modern exocoetid flying fishes, but the evolutionary origin of this strategy was poorly known in the thoracopterids because of lack of transitional forms. Until recently, all thoracopterids, from the Late Triassic of Austria and Italy and the Middle Triassic of South China, were highly specialized 'four-winged' gliders in having wing-like paired fins and an asymmetrical caudal fin with the lower caudal lobe notably larger than the upper lobe. Here, we show that the new genus Wushaichthys and the previously alleged 'peltopleurid' Peripeltopleurus, from the Middle Triassic (Ladinian, 235-242 Ma) of South China and near the Ladinian/Anisian boundary of southern Switzerland and northern Italy, respectively, represent the most primitive and oldest known thoracopterids. Wushaichthys, the most basal thoracopterid, shows certain derived features of this group in the skull. Peripeltopleurus shows a condition intermediate between Wushaichthys and Thoracopterus in having a slightly asymmetrical caudal fin but still lacking wing-like paired fins. Phylogenetic studies suggest that the evolution of overwater gliding of thoracopterids was gradual in nature; a four-stage adaption following the 'cranial specialization-asymmetrical caudal fin-enlarged paired fins-scale reduction' sequence has been recognized in thoracopterid evolution. Moreover, Wushaichthys and Peripeltopleurus bear hooklets on the anal fin of supposed males, resembling those of modern viviparious teleosts. Early thoracopterids probably had evolved a live-bearing reproductive strategy. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Early evolution of the lungfish pectoral fin endoskeleton: evidence from the Middle Devonian (Givetian) Pentlandia macroptera

NASA Astrophysics Data System (ADS)

Jude, Emma; Johanson, Zerina; Kearsley, Anton; Friedman, Matt

2014-08-01

As the closest living relatives of tetrapods, lungfishes are frequently used as extant models for exploring the fin-to-limb transition. These studies have generally given little consideration to fossil taxa. This is because although lungfish fins are relatively common in the fossil record, the internal structure of these fins is virtually unknown. Information on pectoral-fin endoskeletons in fossil representatives of Dipnomorpha (the lungfish total group) is limited to poorly preserved remains in the lungfish Dipterus and Conchopoma and more complete material in the porolepiform Glyptolepis. Here we describe a well-preserved pectoral-fin endoskeleton in the Middle Devonian (Givetian) lungfish Pentlandia macroptera from the John O’Groats fish bed, Caithness, northeastern Scotland. The skeleton is in association with a cleithrum and clavicle, and consists of a series of at least eight mesomeres. Extensive series of preaxial and postaxial radials are present. Some of the radials are jointed, but none branch. No mesomere articulates with multiple radials on either its pre- or post-axial face. The first two mesomeres, corresponding to the humerus and ulna, bear well-developed axial processes. Uniquely among dipnomorphs, a distinct ossification centre corresponding to the radius is present in Pentlandia. A review of anatomy and development of the pectoral-fin endoskeleton in the living Neoceratodus is presented based on cleared and stained material representing different size stages. These developmental data, in conjunction with new details of primitive lungfish conditions based on Pentlandia, highlight many of the derived features of the pectoral-fin skeleton of Neoceratodus, and clarify patterns of appendage evolution within the dipnomorphs more generally.

Ontogenetic scaling of caudal fin shape in Squalus acanthias (Chondrichthyes, Elasmobranchii): a geometric morphometric analysis with implications for caudal fin functional morphology.

PubMed

Reiss, Katie L; Bonnan, Matthew F

2010-07-01

The shark heterocercal caudal fin and its contribution to locomotion are of interest to biologists and paleontologists. Current hydrodynamic data show that the stiff dorsal lobe leads the ventral lobe, both lobes of the tail are synchronized during propulsion, and tail shape reflects its overall locomotor function. Given the difficulties surrounding the analysis of shark caudal fins in vivo, little is known about changes in tail shape related to ontogeny and sex in sharks. A quantifiable analysis of caudal fin shape may provide an acceptable proxy for inferring gross functional morphology where direct testing is difficult or impossible. We examined ontogenetic and sex-related shape changes in the caudal fins of 115 Squalus acanthias museum specimens, to test the hypothesis that significant shape changes in the caudal fin shape occur with increasing size and between the sexes. Using linear and geometric morphometrics, we examined caudal shape changes within the context of current hydrodynamic models. We found no statistically significant linear or shape difference between sexes, and near-isometric scaling trends for caudal dimensions. These results suggest that lift and thrust increase linearly with size and caudal span. Thin-plate splines results showed a significant allometric shape change associated with size and caudal span: the dorsal lobe elongates and narrows, whereas the ventral lobe broadens and expands ventrally. Our data suggest a combination of caudal fin morphology with other body morphology aspects, would refine, and better elucidate the hydrodynamic factors (if any) that underlie the significant shape changes we report here for S. acanthias.

Aerodynamic flight control to increase payload capability of future launch vehicles

NASA Technical Reports Server (NTRS)

Cochran, John E., Jr.; Cheng, Y.-M.; Leleux, Todd; Bigelow, Scott; Hasbrook, William

1993-01-01

In this report, we provide some examples of French, Russian, Chinese, and Japanese launch vehicles that have utilized fins in their designs. Next, the aerodynamic design of the fins is considered in Section 3. Some comments on basic static stability and control theory are followed by a brief description of an aerodynamic characteristics prediction code that was used to estimate the characteristics of a modified NLS 1.5 Stage vehicle. Alternative fin designs are proposed and some estimated aerodynamic characteristics presented and discussed. Also included in Section 3 is a discussion of possible methods of enhancement of the aerodynamic efficiency of fins, such as vortex generators and jet flaps. We consider the construction of fins for launch vehicles in Section 4 and offer an assessment of the state-of-the-art in the use of composites for aerodynamic control surfaces on high speed vehicles. We also comment on the use of smart materials for launch vehicle fins. The dynamic stability and control of a launch vehicle that utilizes both thrust vector control (engine nozzle gimballing) and movable fins is the subject addressed in Section 5. We give a short derivation of equations of motion for a launch vehicle moving in a vertical plane above a spherical earth, discuss the use of a gravity-turn nominal trajectory, and give the form of the period equations linearized about such a nominal. We then consider feedback control of vehicle attitude using both engine gimballing and fin deflection. Conclusions are stated and recommendations made in Section 6. An appendix contains aerodynamic data in tabular and graphical formats.

Mediterranean Fin Whales (Balaenoptera physalus) Threatened by Dolphin MorbilliVirus.

PubMed

Mazzariol, Sandro; Centelleghe, Cinzia; Beffagna, Giorgia; Povinelli, Michele; Terracciano, Giuliana; Cocumelli, Cristiano; Pintore, Antonio; Denurra, Daniele; Casalone, Cristina; Pautasso, Alessandra; Di Francesco, Cristina Esmeralda; Di Guardo, Giovanni

2016-02-01

During 2011-2013, dolphin morbillivirus was molecularly identified in 4 stranded fin whales from the Mediterranean Sea. Nucleoprotein, phosphoprotein, and hemagglutinin gene sequences of the identified strain were highly homologous with those of a morbillivirus that caused a 2006-2007 epidemic in the Mediterranean. Dolphin morbillivirus represents a serious threat for fin whales.

Assessment of Caudal Fin Clips as a Non-lethal Technique for Predicting Muscle Tissue Mercury Concentrations in Largeouth Bass

EPA Science Inventory

The statistical relationship between total mercury (Hg) concentration in clips from the caudal fin and muscle tissue of largemouth bass (Micropterus salmoides) from 26 freshwater sites in Rhode Island, USA was developed and evaluated to determine the utility of fin clip analysis ...

76 FR 19473 - Chrysler Financial Services Americas, LLC, a Subsidiary of FinCo Intermediate Holding Co., LLC...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-07

... Services Americas, LLC, a Subsidiary of FinCo Intermediate Holding Co., LLC, Troy Customer Contact Center... Co., LLC, Troy Customer Contact Center, Troy, Michigan (subject firm). The Department's Notice was... Services Americas, LLC, a subsidiary of FinCo Intermediate Holding Co., LLC, Troy Customer Contact Center...

50 CFR 300.181 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... dorsal and anal fins and forward of the tail fin. Fish or fish products regulated under this subpart... these species, except parts other than meat (e.g., heads, eyes, roe, guts, and tails), and shark fins... previous sentence with respect to fish caught in the exclusive economic zone or by a vessel of the United...

50 CFR 300.181 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... dorsal and anal fins and forward of the tail fin. Fish or fish products regulated under this subpart... these species, except parts other than meat (e.g., heads, eyes, roe, guts, and tails), and shark fins... previous sentence with respect to fish caught in the exclusive economic zone or by a vessel of the United...

Demonstration of Corrosion-Resistant Coatings for Air-Conditioning Coils and Fins

DTIC Science & Technology

2015-06-01

of their respective owners. The findings of this report are not to be construed as an official Department of the Army position unless so designated by...13 Figure 9. HVAC condenser fins with Coating E after on-site exposure for 24 months...14 Figure 10. HVAC condenser fins with

Design and control of an embedded vision guided robotic fish with multiple control surfaces.

PubMed

Yu, Junzhi; Wang, Kai; Tan, Min; Zhang, Jianwei

2014-01-01

This paper focuses on the development and control issues of a self-propelled robotic fish with multiple artificial control surfaces and an embedded vision system. By virtue of the hybrid propulsion capability in the body plus the caudal fin and the complementary maneuverability in accessory fins, a synthesized propulsion scheme including a caudal fin, a pair of pectoral fins, and a pelvic fin is proposed. To achieve flexible yet stable motions in aquatic environments, a central pattern generator- (CPG-) based control method is employed. Meanwhile, a monocular underwater vision serves as sensory feedback that modifies the control parameters. The integration of the CPG-based motion control and the visual processing in an embedded microcontroller allows the robotic fish to navigate online. Aquatic tests demonstrate the efficacy of the proposed mechatronic design and swimming control methods. Particularly, a pelvic fin actuated sideward swimming gait was first implemented. It is also found that the speeds and maneuverability of the robotic fish with coordinated control surfaces were largely superior to that of the swimming robot propelled by a single control surface.

Fin Buffeting Features of an Early F-22 Model

NASA Technical Reports Server (NTRS)

Moses, Robert W.; Huttsell, Lawrence

2000-01-01

Fin buffeting is an aeroelastic phenomenon encountered by high performance aircraft, especially those with twin vertical tails that must operate at high angles of attack. This buffeting is a concern from fatigue and inspection points of view. To date, the buffet (unsteady pressures) and buffeting (structural response) characteristics of the F-15 and F/A-18 fins have been studied extensively using flow visualization, flow velocity measurements, pressure transducers, and response gages. By means of windtunnel and flight tests of the F-15 and F/A-18, this phenomenon is well studied to the point that buffet loads can be estimated and fatigue life can he increased by structural enhancements to these airframes. However, prior to the present research, data was not available outside the F-22 program regarding fin buffeting on the F-22 configuration. During a test in the Langley Transonic Dynamics Tunnel, flow visualization and unsteady fin surface pressures were recorded for a 13.3%-scale F-22 model at high angles of attack for the purpose of comparing with results available for similar aircraft configurations. Details of this test and fin buffeting are presented herein.

Optimization of geometric parameters of heat exchange pipes pin finning

NASA Astrophysics Data System (ADS)

Akulov, K. A.; Golik, V. V.; Voronin, K. S.; Zakirzakov, A. G.

2018-05-01

The work is devoted to optimization of geometric parameters of the pin finning of heat-exchanging pipes. Pin fins were considered from the point of view of mechanics of a deformed solid body as overhang beams with a uniformly distributed load. It was found out under what geometric parameters of the nib (diameter and length); the stresses in it from the influence of the washer fluid will not exceed the yield strength of the material (aluminum). Optimal values of the geometric parameters of nibs were obtained for different velocities of the medium washed by them. As a flow medium, water and air were chosen, and the cross section of the nibs was round and square. Pin finning turned out to be more than 3 times more compact than circumferential finning, so its use makes it possible to increase the number of fins per meter of the heat-exchanging pipe. And it is well-known that this is the main method for increasing the heat transfer of a convective surface, giving them an indisputable advantage.

Chromium Is Elevated in Fin Whale (Balaenoptera physalus) Skin Tissue and Is Genotoxic to Fin Whale Skin Cells

PubMed Central

Wise, Catherine F.; Wise, Sandra S.; Thompson, W. Douglas; Perkins, Christopher; Wise, John Pierce

2015-01-01

Hexavalent chromium (Cr(VI)) is present in the marine environment and is a known carcinogen and reproductive toxicant. Cr(VI) is the form of chromium that is well absorbed through the cell membrane. It is also the most prevalent form in seawater. We measured the total Cr levels in skin biopsies obtained from healthy free-ranging fin whales from the Gulf of Maine and found elevated levels relative to marine mammals in other parts of the world. The levels in fin whale biopsies ranged from 1.71 ug/g to 19.6 ug/g with an average level of 10.07 ug/g. We also measured the cytotoxicity and genotoxicity of Cr(VI) in fin whale skin cells. We found that particulate and soluble Cr(VI) are both cytotoxic and genotoxic to fin whale skin cells in a concentration-dependent manner. The concentration range used in our cell culture studies used environmentally relevant concentrations based on the biopsy measurements. These data suggest that Cr(VI) may be a concern for whales in the Gulf of Maine. PMID:25805270

Propulsive Forces of a Biomimetic Undulating Fin

NASA Astrophysics Data System (ADS)

Kalumuck, Kenneth; Brandt, Alan; Armand, Mehran

2007-11-01

Understanding gained from much recent work on force production mechanisms of aquatic organisms holds great promise for improved undersea vehicle propulsion and maneuvering. One class of fish locomotion is that of the median fin utilized by animals such as squid, cuttlefish, knifefish, and seahorse. It is characterized by undulatory motion that creates traveling waves along the fin. Results of experiments conducted on a submerged mechanical underwater undulating fin test bed are presented. The 0.5 m long fin is mounted to a cylindrical body and consists of a flexible skin attached to ribs driven by an adjustable cam mechanism and variable speed motor that enables changing the characteristics of the undulating wave(s). Forces produced were measured in a captive mode under quiescent conditions as well in the presence of an ambient current. Propulsive forces are characterized as a function of the fin width, oscillation frequency, amplitude, and wavelength. Free swimming experiments were also conducted to determine the point of self propulsion. Flow field structure visualization using dye tracers is presented for selected cases. Estimates of performance and applications for use with larger scale vehicles are discussed.

Experimental study on heat transfer performance of fin-tube exchanger and PSHE for waste heat recovery

NASA Astrophysics Data System (ADS)

Chen, Ting; Bae, Kyung Jin; Kwon, Oh Kyung

2018-02-01

In this paper, heat transfer characteristics of fin-tube heat exchanger and primary surface heat exchanger (PSHE) used in waste heat recovery were investigated experimentally. The flow in the fin-tube heat exchanger is cross flow and in PSHE counter flow. The variations of friction factor and Colburn j factor with air mass flow rate, and Nu number with Re number are presented. Various comparison methods are used to evaluate heat transfer performance, and the results show that the heat transfer rate of the PSHE is on average 17.3% larger than that of fin-tube heat exchanger when air mass flow rate is ranging from 1.24 to 3.45 kg/min. However, the PSHE causes higher pressure drop, and the fin-tube heat exchanger has a wider application range which leads to a 31.7% higher value of maximum heat transfer rate compared to that of the PSHE. Besides, under the same fan power per unit frontal surface, a higher heat transfer rate value is given in the fin-tube heat exchanger.

A comparison of pectoral fin contact between two different wild dolphin populations

USGS Publications Warehouse

Dudzinski, K.M.; Gregg, J.D.; Ribic, C.A.; Kuczaj, S.A.

2009-01-01

Contact behaviour involving the pectoral fin has been documented in a number of dolphin species, and various explanations about its function have been offered. Pectoral fin contact can take a variety of forms, and involves a number of body parts and movements, likely differing depending upon social or ecological context. For this study, we compare the pectoral fin contact behaviour of two species of wild dolphins: Indo-Pacific bottlenose dolphins (Tursiops aduncus) from around Mikura Island, Japan, and Atlantic spotted dolphins (Stenella frontalis) from The Bahamas. The two study populations exhibit surprising similarity in the ways in which pectoral fin contacts are used, despite differences in species and environmental conditions at the two sites. Differences in contact rates for calves between the two sites suggest that calf-focused aggression from adult dolphins is more prevalent at Mikura than in The Bahamas. Our results suggest that pectoral fin contact behaviour seems to be driven primarily by social pressures, and may be similar in function to allogrooming described in primates. ?? 2008 Elsevier B.V.

Design and Control of an Embedded Vision Guided Robotic Fish with Multiple Control Surfaces

PubMed Central

Wang, Kai; Tan, Min; Zhang, Jianwei

2014-01-01

This paper focuses on the development and control issues of a self-propelled robotic fish with multiple artificial control surfaces and an embedded vision system. By virtue of the hybrid propulsion capability in the body plus the caudal fin and the complementary maneuverability in accessory fins, a synthesized propulsion scheme including a caudal fin, a pair of pectoral fins, and a pelvic fin is proposed. To achieve flexible yet stable motions in aquatic environments, a central pattern generator- (CPG-) based control method is employed. Meanwhile, a monocular underwater vision serves as sensory feedback that modifies the control parameters. The integration of the CPG-based motion control and the visual processing in an embedded microcontroller allows the robotic fish to navigate online. Aquatic tests demonstrate the efficacy of the proposed mechatronic design and swimming control methods. Particularly, a pelvic fin actuated sideward swimming gait was first implemented. It is also found that the speeds and maneuverability of the robotic fish with coordinated control surfaces were largely superior to that of the swimming robot propelled by a single control surface. PMID:24688413

Protective Role of Comfrey Leave Extracts on UV-induced Zebrafish Fin Damage

PubMed Central

Cheng, Chien-Chung; Chou, Chi-Yuan; Chang, Yao-Chin; Wang, Hsuan-Wen; Wen, Chi-Chung; Chen, Yau-Hung

2014-01-01

In zebrafish, UV exposure leads to fin malformation phenotypes including fin reduction or absence. The present study evaluated UV-protective activities of comfrey leaves extracts in a zebrafish model by recording fin morphological changes. Chemopreventive effects of comfrey leave extracts were evaluated using Kaplan-Meier analysis and Cox proportional hazards regression. The results showed that (1) the mean times of return to normal fin in the UV+comfrey (50 and 100 ppm) groups were 3.43 and 2.86 days and were quicker compared with that in the UV only group (4.21 days); (2) zebrafish fins in the UV+comfrey (50 and 100 ppm) groups were 2.05 and 3.25 times more likely to return to normal than those in the UV only group; and (3) comfrey leave extracts had UV-absorbance abilities and significantly reduced ROS production in UV-exposed zebrafish embryos, which may attenuate UV-mediated apoptosis. In conclusion, comfrey leaves extracts may have the potential to be developed as UV-protective agents to protect zebrafish embryos from UV-induced damage. PMID:25352712

Heterochronic shift in Hox-mediated activation of sonic hedgehog leads to morphological changes during fin development.

PubMed

Sakamoto, Koji; Onimaru, Koh; Munakata, Keijiro; Suda, Natsuno; Tamura, Mika; Ochi, Haruki; Tanaka, Mikiko

2009-01-01

We explored the molecular mechanisms of morphological transformations of vertebrate paired fin/limb evolution by comparative gene expression profiling and functional analyses. In this study, we focused on the temporal differences of the onset of Sonic hedgehog (Shh) expression in paired appendages among different vertebrates. In limb buds of chick and mouse, Shh expression is activated as soon as there is a morphological bud, concomitant with Hoxd10 expression. In dogfish (Scyliorhinus canicula), however, we found that Shh was transcribed late in fin development, concomitant with Hoxd13 expression. We utilized zebrafish as a model to determine whether quantitative changes in hox expression alter the timing of shh expression in pectoral fins of zebrafish embryos. We found that the temporal shift of Shh activity altered the size of endoskeletal elements in paired fins of zebrafish and dogfish. Thus, a threshold level of hox expression determines the onset of shh expression, and the subsequent heterochronic shift of Shh activity can affect the size of the fin endoskeleton. This process may have facilitated major morphological changes in paired appendages during vertebrate limb evolution.

Fin-and-tube heat exchanger material and inlet velocity effect under frosting conditions

NASA Astrophysics Data System (ADS)

Keryakos, Elie; Toubassy, Joseph; Danlos, Amélie; Clodic, Denis; Descombes, Georges

2017-02-01

The frosting fin-and-tube heat exchanger used in this study is implemented in the dehydration process of a biogas upgrading pilot. Water is separated from the biogas by frosting it at very low temperatures on the cold surfaces of the fin-and-tube heat exchanger. Once frosted, a defrosting system is used to remove water from the process. The main interest of this study is the frosting system. The effects of the biogas velocity, fin material, tube material and frost layer thickness on the performance of the fin-and-tube heat exchanger are investigated. Increasing the biogas velocity tends to increase the frosting layer thickness and the external pressure drop. This will lead to decrease the heat exchanger performance and the frosting cycle duration. The thermal conductivity of the fins and tubes has a major effect on the performance of the heat exchanger. Higher thermal conductivity decreases the heat exchanged surface. A numerical model has been developed, then numerical and experimental results extracted from a biogas upgrading pilot are compared.

Functional analysis of limb enhancers in the developing fin

PubMed Central

Booker, Betty M.; Murphy, Karl K.

2013-01-01

Despite diverging ~365 million years ago, tetrapod limbs and pectoral fins express similar genes that could be regulated by shared regulatory elements. In this study, we set out to analyze the ability of enhancers to maintain tissue specificity in these two divergent structures. We tested 22 human sequences that were previously reported as mouse limb enhancers for their enhancer activity in zebrafish (Danio rerio). Using a zebrafish enhancer assay, we found that 10/22 (45 %) were positive for pectoral fin activity. Analysis of the various criteria that correlated with positive fin activity found that both spatial limb activity and evolutionary conservation are not good predictors of fin enhancer activity. These results suggest that zebrafish enhancer assays may be limited in detecting human limb enhancers, and this limitation does not improve by the use of limb spatial expression or evolutionary conservation. PMID:24068387

Species composition of the international shark fin trade assessed through a retail-market survey in Hong Kong.

PubMed

Fields, Andrew T; Fischer, Gunter A; Shea, Stanley K H; Zhang, Huarong; Abercrombie, Debra L; Feldheim, Kevin A; Babcock, Elizabeth A; Chapman, Demian D

2018-04-01

The shark fin trade is a major driver of shark exploitation in fisheries all over the world, most of which are not managed on a species-specific basis. Species-specific trade information highlights taxa of particular concern and can be used to assess the efficacy of management measures and anticipate emerging threats. The species composition of the Hong Kong Special Administrative Region of China, one of the world's largest fin trading hubs, was partially assessed in 1999-2001. We randomly selected and genetically identified fin trimmings (n = 4800), produced during fin processing, from the retail market of Hong Kong in 2014-2015 to assess contemporary species composition of the fin trade. We used nonparametric species estimators to determine that at least 76 species of sharks, batoids, and chimaeras supplied the fin trade and a Bayesian model to determine their relative proportion in the market. The diversity of traded species suggests species substitution could mask depletion of vulnerable species; one-third of identified species are threatened with extinction. The Bayesian model suggested that 8 species each comprised >1% of the fin trimmings (34.1-64.2% for blue [Prionace glauca], 0.2-1.2% for bull [Carcharhinus leucas] and shortfin mako [Isurus oxyrinchus]); thus, trade was skewed to a few globally distributed species. Several other coastal sharks, batoids, and chimaeras are in the trade but poorly managed. Fewer than 10 of the species we modeled have sustainably managed fisheries anywhere in their range, and the most common species in trade, the blue shark, was not among them. Our study and approach serve as a baseline to track changes in composition of species in the fin trade over time to better understand patterns of exploitation and assess the effects of emerging management actions for these animals. © 2017 The Authors. Conservation Biology published by Wiley Periodicals, Inc. on behalf of Society for Conservation Biology.

Swimming performance of a bio-inspired robotic vessel with undulating fin propulsion.

PubMed

Liu, Hanlin; Curet, Oscar M

2018-06-18

Undulatory fin propulsion exhibits high degree of maneuver control -- an ideal for underwater vessels exploring complex environments. In this work, we developed and tested a self-contained, free-swimming robot with a single undulating fin running along the length of the robot, which controls both forward motion and directional maneuvers. We successfully replicated several maneuvers including forward swimming, reversed motion, diving, station-keeping and vertical swimming. For each maneuver, a series of experiments were performed as a function of fin frequency, wavelength and traveling wave direction to measure swimming velocities, orientation angles and mean power consumption. In addition, three-dimensional flow fields were measured during forward swimming and station-keeping using volumetric particle image velocimetry (PIV). The efficiency for forward swimming was compared using three metrics: cost of transport, wave efficiency and Strouhal number. The results indicate that the cost of transport exhibits a V-shape trend with the minimum value at low swimming velocity. The robot can reach optimal wave efficiency and locomotor performance at a range of 0.2 to 0.4 St. Volumetric PIV data reveal the shed of vortex tubes generated by the fin during forward swimming and station keeping. For forward swimming, a series of vortex tubes are shed off the fin edge with a lateral and downward direction with respect to the longitudinal axis of the fin. For station keeping, flow measurements suggest that the vortex tubes are shed at the mid-section of the fin while the posterior and anterior segment of the vortex stay attached to the fin. These results agree with the previous vortex structures based on simulations and 2D PIV. The further development of this vessel with high maneuverability and station keeping performance can be used for oceanography, coastal exploration, defense, oil industry and other marine industries where operations are unsafe or impractical for divers or human-piloted vessels. © 2018 IOP Publishing Ltd.

The evaluation of the rolling moments induced by wraparound fins

NASA Technical Reports Server (NTRS)

Seginer, A.; Bar-Haim, B.

1983-01-01

A possible reason is suggested for the induced rolling moments occurring on wraparound-fin configurations in subsonic flight at zero angle of attack. The subsonic potential flow over the configuration at zero incidence is solved numerically. The body is simulated by a distribution of sources along its axis, and the fins are described by a vortex-lattice method. It is shown that rolling moments can be induced on the antisymmetric fins by the radial flow generated at the base of the configuration, either over the converging separated wake, or over the diverging plume of a rocket motor.

Schistura maculosa, a new species of loach (Teleostei: Nemacheilidae) from Mizoram, northeastern India.

PubMed

Lalronunga, Samuel; Lalnuntluanga; Lalramliana

2013-01-01

Schistura maculosa, a new species of loach, is described from Tuingo and Pharsih Rivers, tributaries of Tuivai River (Barak drainage) in Mizoram, northeastern India. It is distinguished from other closely related Schistura species in having an axillary pelvic lobe; an incomplete lateral line; 20-30 narrow black bars on the body; 3-4 rows of black spots horizontally across the dorsal-fin; a slightly emarginate caudal-fin, with 5-7 rows of black spots more or less regularly arranged vertically on rays across the fin, and 8+8 branched caudal-fin rays.

Analytical study of temperature distribution in a rectangular porous fin considering both insulated and convective tip

NASA Astrophysics Data System (ADS)

Deshamukhya, Tuhin; Bhanja, Dipankar; Nath, Sujit; Maji, Ambarish; Choubey, Gautam

2017-07-01

The following study is concerned with determination of temperature distribution of porous fins under convective and insulated tip conditions. The authors have made an effort to study the effect of various important parameters involved in the transfer of heat through porous fins as well as the temperature distribution along the fin length subjected to both convective as well as insulated ends. The non-linear equation obtained has been solved by Adomian Decomposition method and validated with a numerical scheme called Finite Difference method by using a central difference scheme and Gauss Siedel Iterative method.

Development of the activated diffusion brazing process for fabrication of finned shell to strut turbine blades

NASA Technical Reports Server (NTRS)

Wilbers, L. G.; Berry, T. F.; Kutchera, R. E.; Edmonson, R. E.

1971-01-01

The activated diffusion brazing process was developed for attaching TD-NiCr and U700 finned airfoil shells to matching Rene 80 struts obstructing the finned cooling passageways. Creep forming the finned shells to struts in combination with precise preplacement of brazing alloy resulted in consistently sound joints, free of cooling passageway clogging. Extensive tensile and stress rupture testing of several joint orientation at several temperatures provided a critical assessment of joint integrity of both material combinations. Trial blades of each material combination were fabricated followed by destructive metallographic examination which verified high joint integrity.

Neuroanatomical organization of the cholinergic system in the central nervous system of a basal actinopterygian fish, the senegal bichir Polypterus senegalus.

PubMed

López, Jesús M; Perlado, Jorge; Morona, Ruth; Northcutt, R Glenn; González, Agustín

2013-01-01

Polypterid bony fishes are believed to be basal to other living ray-finned fishes, and their brain organization is therefore critical in providing information as to primitive neural characters that existed in the earliest ray-finned fishes. The cholinergic system has been characterized in more advanced ray-finned fishes, but not in polypterids. In order to establish which cholinergic neural centers characterized the earliest ray-finned fishes, the distribution of choline acetyltransferase (ChAT) is described in Polypterus and compared with the distribution of this molecule in other ray-finned fishes. Cell groups immunoreactive for ChAT were observed in the hypothalamus, the habenula, the optic tectum, the isthmus, the cranial motor nuclei, and the spinal motor column. Cholinergic fibers were observed in both the telencephalic pallium and the subpallium, in the thalamus and pretectum, in the optic tectum and torus semicircularis, in the mesencephalic tegmentum, in the cerebellar crest, in the solitary nucleus, and in the dorsal column nuclei. Comparison of the data within a segmental neuromeric context indicates that the cholinergic system in polypterid fishes is generally similar to that in other ray-finned fishes, but cholinergic-positive neurons in the pallium and subpallium, and in the thalamus and cerebellum, of teleosts appear to have evolved following the separation of polypterids and other ray-finned fishes. Copyright © 2012 Wiley Periodicals, Inc.

Pelvic girdle and fin of Tiktaalik roseae

PubMed Central

Shubin, Neil H.; Daeschler, Edward B.; Jenkins, Farish A.

2014-01-01

A major challenge in understanding the origin of terrestrial vertebrates has been knowledge of the pelvis and hind appendage of their closest fish relatives. The pelvic girdle and appendage of tetrapods is dramatically larger and more robust than that of fish and contains a number of structures that provide greater musculoskeletal support for posture and locomotion. The discovery of pelvic material of the finned elpistostegalian, Tiktaalik roseae, bridges some of these differences. Multiple isolated pelves have been recovered, each of which has been prepared in three dimensions. Likewise, a complete pelvis and partial pelvic fin have been recovered in association with the type specimen. The pelves of Tiktaalik are paired and have broad iliac processes, flat and elongate pubes, and acetabulae that form a deep socket rimmed by a robust lip of bone. The pelvis is greatly enlarged relative to other finned tetrapodomorphs. Despite the enlargement and robusticity of the pelvis of Tiktaalik, it retains primitive features such as the lack of both an attachment for the sacral rib and an ischium. The pelvic fin of Tiktaalik (NUFV 108) is represented by fin rays and three endochondral elements: other elements are not preserved. The mosaic of primitive and derived features in Tiktaalik reveals that the enhancement of the pelvic appendage of tetrapods and, indeed, a trend toward hind limb-based propulsion have antecedents in the fins of their closest relatives. PMID:24449831

Comparison of rainbow smelt age estimates from fin rays and otoliths

USGS Publications Warehouse

Walsh, M.G.; Maloy, A.P.; O'Brien, T. P.

2008-01-01

Rainbow smelt Osmerus mordax, although nonnative, are an important component of the offshore food web in the Laurentian Great Lakes. In Lake Ontario, we estimate ages of rainbow smelt annually to study population dynamics such as year-class strength and age-specific growth and mortality. Since the early 1980s, we have used pectoral fin rays to estimate rainbow smelt ages, but the sectioning and mounting of fin rays are time and labor intensive. Our objective was to assess the feasibility of using otoliths rather than fin rays to estimate rainbow smelt ages. Three readers interpreted the ages of 172 rainbow smelt (60-198 mm total length) based on thin sections of pectoral fin rays, whole otoliths with no preparation, and whole otoliths that had been cleared for 1 month in a 70:30 ethanol : glycerin solution. Bias was lower and precision was greater for fin rays than for otoliths; these results were consistent for comparisons within readers (first and second readings by one individual; three readers were used) and between readers (one reading for each reader within a pair). Both otolith methods appeared to misclassify age-1 rainbow smelt. Fin ray ages had the highest precision and provided the best approximation of age estimates inferred from the Lake Ontario population's length frequency distribution and from our understanding of this population. ?? American Fisheries Society 2008.

A novel mini-DNA barcoding assay to identify processed fins from internationally protected shark species.

PubMed

Fields, Andrew T; Abercrombie, Debra L; Eng, Rowena; Feldheim, Kevin; Chapman, Demian D

2015-01-01

There is a growing need to identify shark products in trade, in part due to the recent listing of five commercially important species on the Appendices of the Convention on International Trade in Endangered Species (CITES; porbeagle, Lamna nasus, oceanic whitetip, Carcharhinus longimanus scalloped hammerhead, Sphyrna lewini, smooth hammerhead, S. zygaena and great hammerhead S. mokarran) in addition to three species listed in the early part of this century (whale, Rhincodon typus, basking, Cetorhinus maximus, and white, Carcharodon carcharias). Shark fins are traded internationally to supply the Asian dried seafood market, in which they are used to make the luxury dish shark fin soup. Shark fins usually enter international trade with their skin still intact and can be identified using morphological characters or standard DNA-barcoding approaches. Once they reach Asia and are traded in this region the skin is removed and they are treated with chemicals that eliminate many key diagnostic characters and degrade their DNA ("processed fins"). Here, we present a validated mini-barcode assay based on partial sequences of the cytochrome oxidase I gene that can reliably identify the processed fins of seven of the eight CITES listed shark species. We also demonstrate that the assay can even frequently identify the species or genus of origin of shark fin soup (31 out of 50 samples).

Hsp47 mediates Cx43-dependent skeletal growth and patterning in the regenerating fin.

PubMed

Bhadra, Joyita; Iovine, M Kathryn

2015-11-01

Skeletal morphogenesis describes how bones achieve their correct shape and size and appropriately position joints. We use the regenerating caudal fin of zebrafish to study this process. Our examination of the fin length mutant short fin (sof (b123)) has revealed that the gap junction protein Cx43 is involved in skeletal morphogenesis by promoting cell proliferation and inhibiting joint formation, thereby coordinating skeletal growth and patterning. Here we demonstrate that serpinh1b is molecularly and functionally downstream of cx43. The gene serpinh1b codes for a protein called Hsp47, a molecular chaperone responsible for proper folding of procollagen molecules. Knockdown of Hsp47 in regenerating fins recapitulates the sof (b123) phenotypes of reduced fin length, reduced segment length and reduced level of cell proliferation. Furthermore, Hsp47 knockdown affects the organization and localization of the collagen-based actinotrichia. Together, our findings reveal that serpinh1b acts in a cx43 dependent manner to regulate cell proliferation and joint formation. We conclude that disruption of the collagen-based extracellular matrix influences signaling events required for cell proliferation, as well as the patterning of skeletal precursor cells that influences segment length. Therefore, we suggest that Hsp47 function is necessary for skeletal growth and patterning during fin regeneration. Copyright © 2015 Elsevier B.V. All rights reserved.

Estimating ages of Utah chubs by use of pectoral fin rays, otoliths, and scales

USGS Publications Warehouse

Griffin, Kayla M; Beard, Zachary S.; Flinders, John M.; Quist, Michael C.

2017-01-01

Utah chub Gila atraria is native to the Upper Snake River system in Wyoming and Idaho and to the Lake Bonneville Basin in Utah and southeastern Idaho. However, the Utah chub has been introduced into many other waterbodies in the western United States, where it competes with ecologically and economically important species. The objectives of this study were to evaluate between-reader precision and reader confidence in age estimates obtained from pectoral fin rays, lapilli (otoliths), asterisci (otoliths), and scales for Utah chubs collected from Henrys Lake, Idaho. Lapilli have been previously shown to provide accurate age estimates for Utah chubs; therefore, we sought to compare age estimates from fin rays, asterisci, and scales to those from lapilli. The between-reader coefficient of variation (CV) in age estimates was lowest and the percent of exact reader agreement (PA-0) was highest for pectoral fin rays (CV = 4.7, PA-0 = 74%), followed by scales (CV = 10.3, PA-0 = 52.3%), lapilli (CV = 11.6, PA-0 = 48.2%), and asterisci (CV = 13.0, PA-0 = 41.7%). Consensus age estimates from pectoral fin rays showed high concordance with consensus age estimates from lapilli. Our results indicate that pectoral fin rays provide the most precise age estimates for Utah chub. Pectoral fin rays are easily collected and processed and also provide age estimates without requiring fish sacrifice.

Control effectiveness and tip-fin dihedral effects for the HL-20 lifting-body configuration at Mach numbers from 1.6 to 4.5

NASA Technical Reports Server (NTRS)

Cruz, Christopher I.; Ware, George M.

1995-01-01

Wind tunnel tests were made with a scale model of the HL-20 in the Langley Unitary Plan Wind Tunnel. Pitch control was investigated by deflecting the elevon surfaces on the outboard fins and body flaps on the fuselage. Yaw control tests were made with the all movable center fin deflected 5 deg. Almost full negative body flap deflection (-30 deg) was required to trim the HL-20 (moment reference center at 0.54-percent body length from nose) to positive values of life in the Mach number range from 1.6 to 2.5. Elevons were twice as effective as body flaps as a longitudinal trim device. The elevons were effective as a roll control, but because of tip-fin dihedral angle, produced about as much adverse yawing moment as rolling moment. The body flaps were less effective in producing rolling moment, but produced little adverse yawing moment. The yaw effectiveness of the all movable center fin was essentially constant over the angle-of-attack range at each Mach number. The value of yawing moment, however, was small. Center-fin deflection produced almost no rolling moments. The model was directionally unstable over most of the Mach number range with tip-fin dihedral angles less than the baseline value of 50 deg.

Fin field effect transistor directionality impacts printing of implantation shapes

NASA Astrophysics Data System (ADS)

Wang, Xiren; Granik, Yuri

2018-01-01

In modern integrated circuit (IC) fabrication processes, the photoresist receives considerable illumination energy that is reflected by underlying topography during optical lithography of implantation layers. Bottom antireflective coating (BARC) is helpful to mitigate the reflection. Often, however, BARC is not used, because its removal is technically challenging, in addition to its relatively high economic cost. Furthermore, the advanced technology nodes, such as 14/10-nm nodes, have introduced fin field effect transistor (FinFET), which makes reflection from nonuniform silicon substrates exceptionally complicated. Therefore, modeling reflection from topography becomes obligatory to accurately predict printing of implantation shapes. Typically, FinFET is always fixed in one direction in realistic designs. However, the same implantation rectangle may be oriented in either horizontal or vertical direction. Then, there are two types of relations between the critical dimension (CD) and FinFET, namely a parallel-to and a perpendicular-to relation. We examine the fin directionality impact on CD. We found that this impact may be considerable in some cases. We use our in-house rigorous optical topography simulator to reveal underlining physical reasons. One of the major causes of the CD differences is that in the parallel orientation, the solid sidewalls of the fins conduct considerable light reflections unlike for the perpendicular orientation. This finding can aid the compact modeling in optical proximity correction of implantation masks.

Mediterranean Fin Whales (Balaenoptera physalus) Threatened by Dolphin MorbilliVirus

PubMed Central

Centelleghe, Cinzia; Beffagna, Giorgia; Povinelli, Michele; Terracciano, Giuliana; Cocumelli, Cristiano; Pintore, Antonio; Denurra, Daniele; Casalone, Cristina; Pautasso, Alessandra; Di Francesco, Cristina Esmeralda; Di Guardo, Giovanni

2016-01-01

During 2011–2013, dolphin morbillivirus was molecularly identified in 4 stranded fin whales from the Mediterranean Sea. Nucleoprotein, phosphoprotein, and hemagglutinin gene sequences of the identified strain were highly homologous with those of a morbillivirus that caused a 2006–2007 epidemic in the Mediterranean. Dolphin morbillivirus represents a serious threat for fin whales. PMID:26812485

A novel field method to distinguish between cryptic carcharhinid sharks, Australian blacktip shark Carcharhinus tilstoni and common blacktip shark C. limbatus, despite the presence of hybrids.

PubMed

Johnson, G J; Buckworth, R C; Lee, H; Morgan, J A T; Ovenden, J R; McMahon, C R

2017-01-01

Multivariate and machine-learning methods were used to develop field identification techniques for two species of cryptic blacktip shark. From 112 specimens, precaudal vertebrae (PCV) counts and molecular analysis identified 95 Australian blacktip sharks Carcharhinus tilstoni and 17 common blacktip sharks Carcharhinus limbatus. Molecular analysis also revealed 27 of the 112 were C. tilstoni × C. limbatus hybrids, of which 23 had C. tilstoni PCV counts and four had C. limbatus PCV counts. In the absence of further information about hybrid phenotypes, hybrids were assigned as either C. limbatus or C. tilstoni based on PCV counts. Discriminant analysis achieved 80% successful identification, but machine-learning models were better, achieving 100% successful identification, using six key measurements (fork length, caudal-fin peduncle height, interdorsal space, second dorsal-fin height, pelvic-fin length and pelvic-fin midpoint to first dorsal-fin insertion). Furthermore, pelvic-fin markings could be used for identification: C. limbatus has a distinct black mark >3% of the total pelvic-fin area, while C. tilstoni has markings with diffuse edges, or has smaller or no markings. Machine learning and pelvic-fin marking identification methods were field tested achieving 87 and 90% successful identification, respectively. With further refinement, the techniques developed here will form an important part of a multi-faceted approach to identification of C. tilstoni and C. limbatus and have a clear management and conservation application to these commercially important sharks. The methods developed here are broadly applicable and can be used to resolve species identities in many fisheries where cryptic species exist. © 2016 The Fisheries Society of the British Isles.

Relationships of mercury concentrations across tissue types, muscle regions and fins for two shark species.

PubMed

O'Bryhim, Jason R; Adams, Douglas H; Spaet, Julia L Y; Mills, Gary; Lance, Stacey L

2017-04-01

Mercury (Hg) exposure poses a threat to both fish and human health. Sharks are known to bioaccumulate Hg, however, little is known regarding how Hg is distributed between different tissue groups (e.g. muscle regions, organs). Here we evaluated total mercury (THg) concentrations from eight muscle regions, four fins (first dorsal, left and right pectorals, caudal-from both the inner core and trailing margin of each fin), and five internal organs (liver, kidney, spleen, heart, epigonal organ) from two different shark species, bonnethead (Sphyrna tiburo) and silky shark (Carcharhinus falciformis) to determine the relationships of THg concentrations between and within tissue groups. Total Hg concentrations were highest in the eight muscle regions with no significant differences in THg concentrations between the different muscle regions and muscle types (red and white). Results from tissue collected from any muscle region would be representative of all muscle sample locations. Total Hg concentrations were lowest in samples taken from the fin inner core of the first dorsal, pectoral, and caudal (lower lobe) fins. Mercury concentrations for samples taken from the trailing margin of the dorsal, pectoral, and caudal fins (upper and lower lobe) were also not significantly different from each other for both species. Significant relationships were found between THg concentrations in dorsal axial muscle tissue and the fin inner core, liver, kidney, spleen and heart for both species as well as the THg concentrations between the dorsal fin trailing margin and the heart for the silky shark and all other sampled tissue types for the bonnethead shark. Our results suggest that biopsy sampling of dorsal muscle can provide data that can effectively estimate THg concentrations in specific organs without using more invasive, or lethal methods. Copyright © 2017 Elsevier Ltd. All rights reserved.

Osteology of the crescent gunnel Pholis laeta and the phylogeny of the family Pholidae (Cottiformes, Zoarcoidei).

PubMed

Sweetser, P W; Hilton, E J

2016-09-01

This study provides a complete description of the osteology of the crescent gunnel Pholis laeta based on cleared-and-stained specimens and X-rays to help provide sufficient morphological data to generate a robust phylogeny for the family Pholidae. Pholis laeta exhibits high variation in the structure of its caudal skeleton. The length of the preural (pu)2 neural spine is variably reduced (most common) or elongated (i.e. of similar length to that of pu3). Additionally, the neural spine of pu3 is either bifurcated or single. These results document and describe characters useful for phylogenetic inference of the family, including the insertion pattern of anal-fin pterygiophores between haemal spines. Pholidae was recovered as monophyletic (synapomorphies: ribs absent, haemonephropophyses present, gill membranes broadly joined, first neural arch fused to centrum, first anal-fin spine very robust, the dorsal fin comprises only spines and the presence of five branchiostegals), with monophyletic genera Pholis and Apodichthys (Rhodymenichthys is monotypic) and Apodichthys and Rhodymenichthys as sister taxa. The elongation of its pu2 neural spine defines Pholis and synapomorphies for Apodichthys include five infraorbital bones, no pelvic fin, a hypertrophied first anal-fin spine, the presence of two or three empty interhaemal spaces after the anteriormost anal-fin spine and having 35-46 abdominal vertebrae. Apodichthys and Rhodymenichthys are sister taxa based on the continuity of the caudal fin with the dorsal and anal fins and uniform colouration. Future study is needed to more fully resolve the interrelationships of species within Pholidae (especially the genus Pholis) and solidify the position of Pholidae within the Zoarcoidei. © 2016 The Fisheries Society of the British Isles.

Tracing the spatio-temporal dynamics of endangered fin whales (Balaenoptera physalus) within baleen whale (Mysticeti) lineages: a mitogenomic perspective.

PubMed

Yu, Jihyun; Nam, Bo-Hye; Yoon, Joon; Kim, Eun Bae; Park, Jung Youn; Kim, Heebal; Yoon, Sook Hee

2017-12-01

To explore the spatio-temporal dynamics of endangered fin whales (Balaenoptera physalus) within the baleen whale (Mysticeti) lineages, we analyzed 148 published mitochondrial genome sequences of baleen whales. We used a Bayesian coalescent approach as well as Bayesian inferences and maximum likelihood methods. The results showed that the fin whales had a single maternal origin, and that there is a significant correlation between geographic location and evolution of global fin whales. The most recent common female ancestor of this species lived approximately 9.88 million years ago (Mya). Here, North Pacific fin whales first appeared about 7.48 Mya, followed by a subsequent divergence in Southern Hemisphere approximately 6.63 Mya and North Atlantic about 4.42 Mya. Relatively recently, approximately 1.76 and 1.42 Mya, there were two additional occurrences of North Pacific populations; one originated from the Southern Hemisphere and the other from an uncertain location. The evolutionary rate of this species was 1.002 × 10 -3 substitutions/site/My. Our Bayesian skyline plot illustrates that the fin whale population has the rapid expansion event since ~ 2.5 Mya, during the Quaternary glaciation stage. Additionally, this study indicates that the fin whale has a sister group relationship with humpback whale (Meganoptera novaeangliae) within the baleen whale lineages. Of the 16 genomic regions, NADH5 showed the most powerful signal for baleen whale phylogenetics. Interestingly, fin whales have 16 species-specific amino acid residues in eight mitochondrial genes: NADH2, COX2, COX3, ATPase6, ATPase8, NADH4, NADH5, and Cytb.

Experimental study of heat transfer and thermal performance with longitudinal fins of solar air heater

PubMed Central

Chabane, Foued; Moummi, Noureddine; Benramache, Said

2013-01-01

The thermal performance of a single pass solar air heater with five fins attached was investigated experimentally. Longitudinal fins were used inferior the absorber plate to increase the heat exchange and render the flow fluid in the channel uniform. The effect of mass flow rate of air on the outlet temperature, the heat transfer in the thickness of the solar collector, and the thermal efficiency were studied. Experiments were performed for two air mass flow rates of 0.012 and 0.016 kg s−1. Moreover, the maximum efficiency values obtained for the 0.012 and 0.016 kg s−1 with and without fins were 40.02%, 51.50% and 34.92%, 43.94%, respectively. A comparison of the results of the mass flow rates by solar collector with and without fins shows a substantial enhancement in the thermal efficiency. PMID:25685486

Experimental study of heat transfer and thermal performance with longitudinal fins of solar air heater.

PubMed

Chabane, Foued; Moummi, Noureddine; Benramache, Said

2014-03-01

The thermal performance of a single pass solar air heater with five fins attached was investigated experimentally. Longitudinal fins were used inferior the absorber plate to increase the heat exchange and render the flow fluid in the channel uniform. The effect of mass flow rate of air on the outlet temperature, the heat transfer in the thickness of the solar collector, and the thermal efficiency were studied. Experiments were performed for two air mass flow rates of 0.012 and 0.016 kg s(-1). Moreover, the maximum efficiency values obtained for the 0.012 and 0.016 kg s(-1) with and without fins were 40.02%, 51.50% and 34.92%, 43.94%, respectively. A comparison of the results of the mass flow rates by solar collector with and without fins shows a substantial enhancement in the thermal efficiency.

Wind-tunnel investigation of effect of interference on lateral-stability characteristics of four NACA 23012 wings, an elliptical and a circular fuselage and vertical fins

NASA Technical Reports Server (NTRS)

House, Rufus O; Wallace, Arthur R

1941-01-01

Report presents the results of a wind-tunnel investigation of the effect of wing-fuselage interference on lateral-stability characteristics made in the NACA 7 by 10-foot wind tunnel on four fuselages and two fins, representing high-wing, low-wing, and midwing monoplanes. The fuselages are of circular and elliptical cross section. The wings have rounded tips and, in plan form, one is rectangular and the three are tapered 3:1 with various amounts of sweep. The rate of change in the coefficients of rolling moment, yawing moment, and lateral force with angle of yaw is given in a form to show the increment caused by wing-fuselage interference for the model with no fin and the effect of wing-fuselage interference on fin effectiveness. Results for the fuselage-fin combination and the wing tested alone are also given.

Total Ionizing Dose Effects on Strained Ge pMOS FinFETs on Bulk Si

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, En Xia; Fleetwood, Daniel M.; Hachtel, Jordan A.

2016-12-02

In this paper, we have characterized the total ionizing dose response of strained Ge p MOS FinFETs built on bulk Si using a fin replacement process. Devices irradiated to 1.0 Mrad(SiO 2) show minimal transconductance degradation (less than 5%), very small V th shifts (less than 40 mV in magnitude) and very little ON/OFF current ratio degradation (<5%), and only modest variation in radiation response with transistor geometry (typically less than normal part-to-part variation). Both before and after irradiation, the performance of these strained Ge p MOS FinFETs is far superior to that of past generations of planar Ge pmore » MOS devices. Finally, these improved properties result from significant improvements in processing technology, as well as the enhanced gate control provided by the strained Ge FinFET technology.« less

Unusual anal fin in a Devonian jawless vertebrate reveals complex origins of paired appendages

PubMed Central

Sansom, Robert S.; Gabbott, Sarah E.; Purnell, M. A.

2013-01-01

Jawed vertebrates (gnathostomes) have undergone radical anatomical and developmental changes in comparison with their jawless cousins (cyclostomes). Key among these is paired appendages (fins, legs and wings), which first evolved at some point on the gnathostome stem. The anatomy of fossil stem gnathostomes is, therefore, fundamental to our understanding of the nature and timing of the origin of this complex innovation. Here, we show that Euphanerops, a fossil jawless fish from the Devonian, possessed paired anal-fin radials, but no pectoral or pelvic fins. This unique condition occurs at an early stage on the stem-gnathostome lineage. This condition, and comparison with the varied condition of paired fins in other ostracoderms, indicates that there was a large amount of developmental plasticity during this episode—rather than a gradual evolution of this complex feature. Apparently, a number of different clades were exploring morphospace or undergoing multiple losses. PMID:23576777

Boiling and condensation in microfin tubes

NASA Astrophysics Data System (ADS)

Schlager, Lynn M.

A general overview of microfin tubes and their applications is presented. Manufacturing processes, commercial availability, experimental heat transfer, and pressure drop data for various refrigerants (including alternative refrigerants and refrigerant-oil mixtures), physical mechanisms of enhancement, and the incorporation of microfin tubes in common heat exchanger configurations are discussed. Microfin tubes, also known by various trade names, are characterized by numerous small fins which typically spiral down the inside wall of tubes at angles ranging from 10 to 30 degrees. The number of fins ranges from 48 to 70 with typical fin heights of 0.12 to 0.30 mm (fin height generally less than 3 percent of the inside diameter of the tube). Fin shapes may vary and the inside surface area of microfin tubes is 10 to 70 percent greater than the area of equivalent smooth tubes. Heat transfer can be enhanced by up to a factor of three with microfin tubes.

Cetacean Social Behavioral Response to Sonar Exposure

DTIC Science & Technology

2015-09-30

Lam FPA, Tyack PLT, Miller PJO (in review). Disturbance-specific social responses in long-finned pilot whales, Globicephala melas .  Fieldwork...the social behavioral response of long-finned pilot whales (Globicephala melas ) revealed that a unifying characteristic of their behavioral response...Globicephala melas . 6 Visser F. et al. (in review). Vocal foragers and silent crowds: the socio-behavioural context of long- finned pilot whale

Fin-line horn antenna

DOEpatents

Reindel, John

1990-01-01

A fin line circuit card containing a fin line slot feeds a dipole antenna ich extends a quarterwave outside the waveguide and provides an energy beam focal point at or near the open end of the waveguide. The dipole antenna thus maintains a wide and nearly constant beamwidth, low VSWR and a circular symmetric radiation pattern for use in electronic warfare direction finding and surveillance applications.

Heat exchange apparatus

DOEpatents

Degtiarenko, Pavel V.

2003-08-12

A heat exchange apparatus comprising a coolant conduit or heat sink having attached to its surface a first radial array of spaced-apart parallel plate fins or needles and a second radial array of spaced-apart parallel plate fins or needles thermally coupled to a body to be cooled and meshed with, but not contacting the first radial array of spaced-apart parallel plate fins or needles.

Investigation of defect-induced abnormal body current in fin field-effect-transistors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Kuan-Ju; Tsai, Jyun-Yu; Lu, Ying-Hsin

2015-08-24

This letter investigates the mechanism of abnormal body current at the linear region in n-channel high-k/metal gate stack fin field effect transistors. Unlike body current, which is generated by impact ionization at high drain voltages, abnormal body current was found to increase with decreasing drain voltages. Notably, the unusual body leakage only occurs in three-dimensional structure devices. Based on measurements under different operation conditions, the abnormal body current can be attributed to fin surface defect-induced leakage current, and the mechanism is electron tunneling to the fin via the defects, resulting in holes left at the body terminal.

Cooling system having reduced mass pin fins for components in a gas turbine engine

DOEpatents

Lee, Ching-Pang; Jiang, Nan; Marra, John J

2014-03-11

A cooling system having one or more pin fins with reduced mass for a gas turbine engine is disclosed. The cooling system may include one or more first surfaces defining at least a portion of the cooling system. The pin fin may extend from the surface defining the cooling system and may have a noncircular cross-section taken generally parallel to the surface and at least part of an outer surface of the cross-section forms at least a quartercircle. A downstream side of the pin fin may have a cavity to reduce mass, thereby creating a more efficient turbine airfoil.

Computational Study of Inbore and Inflight Heating for the 105MM, M774 Projectile Modified Swept Fin.

DTIC Science & Technology

1984-08-01

local 1* H. A. Dwyjer, R. J. K~ee, and B. R., Sanderse, "Adaptive Gr’id Method for’ ProbZe s in Ftuid Mechanie and Heat Transfer," 44.AL...A a.4 VoZ . 18...within the fin, heat conduction at the fin root into the pro- jectile body , and surface heat transfer at the fin tip. Other limitations in the heat...Figures 17a,b and 18a,b. From these figures the effect appears to be localized in the trailing edge region and no influence at the critical area near

A new species of Triplophysa Rendahl (Cypriniformes, Nemacheilidae) from Sichuan Province, China

PubMed Central

YAN, Si-Li; SUN, Zhi-Yu; GUO, Yan-Shu

2015-01-01

Triplophysa yajiangensis sp. nov. is described from the upper and middle reaches of the Yalong River, Yangtze Basin, Ganzi Prefecture, Sichuan Province, China. This new species can be distinguished from other congeneric species by the following characters: body surface smooth and scaleless; lateral line complete; caudal peduncle compressed and tapered slightly; lower jaw shovel-shaped; head shorter than caudal peduncle; dorsal-fin origin anterior to pelvic-fin origin and closer to tip of snout than to caudal-fin base, last unbranched ray hard; pelvic-fin reaches or exceeds anus; posterior chamber of gas bladder absent; intestine spiral type with 3-5 winding coils. PMID:26452694

The effect of diet on dorsal fin erosion in steelhead trout (Oncorhynchus mykiss)

USGS Publications Warehouse

Lellis, W.A.; Barrows, F.T.

1997-01-01

A 2 X 2 factorial experiment of diet type (krill vs. fish meal) and steroid supplementation (0 vs. 30 ??g 17??-methyltestosterone kg-1) was conducted to determine the effects on dorsal fin erosion in steelhead trout. Triplicate tanks of 250 fry were fed one of the four diets at a rate calculated to produce 115 g fish in 34 weeks. Fish were transferred to larger tanks when mean density index reached 0.40. Dorsal fin index (DFI, measured as mean dorsal fin height X 100/total fish length) was greater (P < 0.001) among fish fed krill-based diets than for fish fed fish-based diets at weeks 12, 22, and 34 of the trial. Added testosterone decreased (p = 0.04) DFI among fish fed the krill diet at week 12 but otherwise had no effect on fin condition. Addition of testosterone to either diet type decreased (P = 0.02) critical thermal maximum, which is a measure of fish resistance to thermal stress. The results suggest that diet composition can influence the rate of dorsal fin erosion in steelhead trout through a metabolic, behavioral, or combined change.

Static Noise Margin Enhancement by Flex-Pass-Gate SRAM

NASA Astrophysics Data System (ADS)

O'Uchi, Shin-Ichi; Masahara, Meishoku; Sakamoto, Kunihiro; Endo, Kazuhiko; Liu, Yungxun; Matsukawa, Takashi; Sekigawa, Toshihiro; Koike, Hanpei; Suzuki, Eiichi

A Flex-Pass-Gate SRAM, i.e. a fin-type-field-effect-transistor- (FinFET-) based SRAM, is proposed to enhance noise margin during both read and write operations. In its cell, the flip-flop is composed of usual three-terminal- (3T-) FinFETs while pass gates are composed of four-terminal- (4T-) FinFETs. The 4T-FinFETs enable to adopt a dynamic threshold-voltage control in the pass gates. During a write operation, the threshold voltage of the pass gates is lowered to enhance the writing speed and stability. During the read operation, on the other hand, the threshold voltage is raised to enhance the static noise margin. An asymmetric-oxide 4T-FinFET is helpful to manage the leakage current through the pass gate. In this paper, a design strategy of the pass gate with an asymmetric gate oxide is considered, and a TCAD-based Monte Carlo simulation reveals that the Flex-Pass-Gate SRAM based on that design strategy is expected to be effective in half-pitch 32-nm technology for low-standby-power (LSTP) applications, even taking into account the variability in the device performance.

Experimental study on the flow/ heat transfer performance of micro-scale pin fin coating with super-hydrophobic surface adding Nano particle

NASA Astrophysics Data System (ADS)

Hua, Junye; Duan, Yuanyuan; Li, Gui; Xu, Qiong; Li, Dong; Wu, Wei; Zhao, Xiaobao; Qiu, Delai

2018-02-01

The experimental studies on heat transfer and flow resistance characteristics of ellipse-shape micro pin fin have been conducted which is drafted with hydrophobic material, holding the various contact angles fulfilled by adjusting the amount of Nano particle. The results show that with the increases of contact angle(83°,99.5°, 119.5°and 151.5°), the bottom wall temperature rises under the same flow rate. Under a certain heating condition with heating power as 100 W, the average convective heat transfer coefficient decreases with the increase of contact angle with the same Re. The value of Nu for ellipse-shape micro pin fin increases with a higher Re, with the maximum value under experimental condition of Nu as 25. Besides, the friction coefficient of micro pin fin experimental section drafted hydrophobicity treatment significantly decreases, compared with the smooth micro pin fin experimental section (θ = 83°). While the higher contact angle has obvious positive influences on friction coefficient under the same Re. Generally, the flow resistance performance of ellipse-shape micro pin fin drafted with hydrophobic material is better than that without any treatment.

A 3-D CFD Analysis of the Space Shuttle RSRM With Propellant Fins @ 1 sec. Burn-Back

NASA Technical Reports Server (NTRS)

Morstadt, Robert A.

2003-01-01

In this study 3-D Computational Fluid Dynamic (CFD) runs have been made for the Space Shuttle RSRM using 2 different grids and 4 different turbulent models, which were the Standard KE, the RNG KE, the Realizable KE, and the Reynolds stress model. The RSRM forward segment consists of 11 fins. By taking advantage of the forward fin symmetry only half of one fin along the axis had to be used in making the grid. This meant that the 3-D model consisted of a pie slice that encompassed 1/22nd of the motor circumference and went along the axis of the entire motor. The 3-D flow patterns in the forward fin region are of particular interest. Close inspection of these flow patterns indicate that 2 counter-rotating axial vortices emerge from each submerged solid propellant fin. Thus, the 3-D CFD analysis allows insight into complicated internal motor flow patterns that are not available from the simpler 2-D axi-symmetric studies. In addition, a comparison is made between the 3-D bore pressure drop and the 2-D axi-symmetric pressure drop.

An antiarch placoderm shows that pelvic girdles arose at the root of jawed vertebrates

PubMed Central

Zhu, Min; Yu, Xiaobo; Choo, Brian; Wang, Junqing; Jia, Liantao

2012-01-01

Almost all gnathostomes or jawed vertebrates (including osteichthyans, chondrichthyans, ‘acanthodians’ and most placoderms) possess paired pectoral and pelvic fins. To date, it has generally been believed that antiarch placoderms (extinct armoured jawed fishes from the Silurian–Devonian periods) lacked pelvic fins. The putative absence of pelvic fins is a key character bearing on the monophyly or paraphyly of placoderms. It also has far-reaching implications for studying the sequence of origin of pelvic girdles versus that of movable jaws in the course of vertebrate evolution. Parayunnanolepis xitunensis represents the only example of a primitive antiarch with extensive post-thoracic preservation, and its original description has been cited as confirming the primitive lack of pelvic fins in early antiarchs. Here, we present a revised description of Parayunnanolepis and offer the first unambiguous evidence for the presence of pelvic girdles in antiarchs. As antiarchs are placed at the base of the gnathostome radiation in several recent studies, our finding shows that all jawed vertebrates (including antiarch placoderms) primitively possess both pectoral and pelvic fins and that the pelvic fins did not arise within gnathostomes at a point subsequent to the origin of jaws. PMID:22219394

Aerodynamic characteristics of flying fish in gliding flight.

PubMed

Park, Hyungmin; Choi, Haecheon

2010-10-01

The flying fish (family Exocoetidae) is an exceptional marine flying vertebrate, utilizing the advantages of moving in two different media, i.e. swimming in water and flying in air. Despite some physical limitations by moving in both water and air, the flying fish has evolved to have good aerodynamic designs (such as the hypertrophied fins and cylindrical body with a ventrally flattened surface) for proficient gliding flight. Hence, the morphological and behavioral adaptations of flying fish to aerial locomotion have attracted great interest from various fields including biology and aerodynamics. Several aspects of the flight of flying fish have been determined or conjectured from previous field observations and measurements of morphometric parameters. However, the detailed measurement of wing performance associated with its morphometry for identifying the characteristics of flight in flying fish has not been performed yet. Therefore, in the present study, we directly measure the aerodynamic forces and moment on darkedged-wing flying fish (Cypselurus hiraii) models and correlated them with morphological characteristics of wing (fin). The model configurations considered are: (1) both the pectoral and pelvic fins spread out, (2) only the pectoral fins spread with the pelvic fins folded, and (3) both fins folded. The role of the pelvic fins was found to increase the lift force and lift-to-drag ratio, which is confirmed by the jet-like flow structure existing between the pectoral and pelvic fins. With both the pectoral and pelvic fins spread, the longitudinal static stability is also more enhanced than that with the pelvic fins folded. For cases 1 and 2, the lift-to-drag ratio was maximum at attack angles of around 0 deg, where the attack angle is the angle between the longitudinal body axis and the flying direction. The lift coefficient is largest at attack angles around 30∼35 deg, at which the flying fish is observed to emerge from the sea surface. From glide polar, we find that the gliding performance of flying fish is comparable to those of bird wings such as the hawk, petrel and wood duck. However, the induced drag by strong wing-tip vortices is one of the dominant drag components. Finally, we examine ground effect on the aerodynamic forces of the gliding flying fish and find that the flying fish achieves the reduction of drag and increase of lift-to-drag ratio by flying close to the sea surface.

Stellar Population Properties of Ultracompact Dwarfs in M87: A Mass–Metallicity Correlation Connecting Low-metallicity Globular Clusters and Compact Ellipticals

NASA Astrophysics Data System (ADS)

Zhang, Hong-Xin; Puzia, Thomas H.; Peng, Eric W.; Liu, Chengze; Côté, Patrick; Ferrarese, Laura; Duc, Pierre-Alain; Eigenthaler, Paul; Lim, Sungsoon; Lançon, Ariane; Muñoz, Roberto P.; Roediger, Joel; Sánchez-Janssen, Ruben; Taylor, Matthew A.; Yu, Jincheng

2018-05-01

We derive stellar population parameters for a representative sample of ultracompact dwarfs (UCDs) and a large sample of massive globular clusters (GCs) with stellar masses ≳ 106 M ⊙ in the central galaxy M87 of the Virgo galaxy cluster, based on model fitting to the Lick-index measurements from both the literature and new observations. After necessary spectral stacking of the relatively faint objects in our initial sample of 40 UCDs and 118 GCs, we obtain 30 sets of Lick-index measurements for UCDs and 80 for GCs. The M87 UCDs have ages ≳ 8 Gyr and [α/Fe] ≃ 0.4 dex, in agreement with previous studies based on smaller samples. The literature UCDs, located in lower-density environments than M87, extend to younger ages and smaller [α/Fe] (at given metallicities) than M87 UCDs, resembling the environmental dependence of the stellar nuclei of dwarf elliptical galaxies (dEs) in the Virgo cluster. The UCDs exhibit a positive mass–metallicity relation (MZR), which flattens and connects compact ellipticals at stellar masses ≳ 108 M ⊙. The Virgo dE nuclei largely follow the average MZR of UCDs, whereas most of the M87 GCs are offset toward higher metallicities for given stellar masses. The difference between the mass–metallicity distributions of UCDs and GCs may be qualitatively understood as a result of their different physical sizes at birth in a self-enrichment scenario or of galactic nuclear cluster star formation efficiency being relatively low in a tidal stripping scenario for UCD formation. The existing observations provide the necessary but not sufficient evidence for tidally stripped dE nuclei being the dominant contributors to the M87 UCDs.

Transformation of a Virgo Cluster dwarf irregular galaxy by ram pressure stripping: IC3418 and its fireballs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kenney, Jeffrey D. P.; Geha, Marla; Jáchym, Pavel

We present optical imaging and spectroscopy and H I imaging of the Virgo Cluster galaxy IC 3418, which is likely a 'smoking gun' example of the transformation of a dwarf irregular into a dwarf elliptical galaxy by ram pressure stripping. IC 3418 has a spectacular 17 kpc length UV-bright tail comprised of knots, head-tail, and linear stellar features. The only Hα emission arises from a few H II regions in the tail, the brightest of which are at the heads of head-tail UV sources whose tails point toward the galaxy ('fireballs'). Several of the elongated tail sources have Hα peaksmore » outwardly offset by ∼80-150 pc from the UV peaks, suggesting that gas clumps continue to accelerate through ram pressure, leaving behind streams of newly formed stars which have decoupled from the gas. Absorption line strengths, measured from Keck DEIMOS spectra, together with UV colors, show star formation stopped 300 ± 100 Myr ago in the main body, and a strong starburst occurred prior to quenching. While neither Hα nor H I emission are detected in the main body of the galaxy, we have detected 4 × 10{sup 7} M {sub ☉} of H I from the tail with the Very Large Array. The velocities of tail H II regions, measured from Keck LRIS spectra, extend only a small fraction of the way to the cluster velocity, suggesting that star formation does not happen in more distant parts of the tail. Stars in the outer tail have velocities exceeding the escape speed, but some in the inner tail should fall back into the galaxy, forming halo streams.« less

The Origin of Dwarf Early-Type Galaxies

NASA Astrophysics Data System (ADS)

Toloba, Elisa

2012-10-01

Abridge. We have conducted a spectrophotometric study of dwarf early-type galaxies (dEs) in the Virgo cluster and in regions of lower density. We have found that these galaxies show many properties in common with late-type galaxies but not with more massive early-types (E/S0). The properties of the dEs in Virgo show gradients within the cluster. dEs in the outer parts of the Virgo cluster are kinematically supported by rotation, while those in the center are supported by the random motions of their stars (i.e. pressure supported). The rotationally supported dEs have disky isophotes and faint underlying spiral/irregular substructures, they also show younger ages than those pressure supported, which have boxy isophotes and are smooth and regular, without any substructure. We compare the position of these dEs with massive early-type galaxies in the Faber-Jackson and Fundamental Plane relations, and we find that, although there is no difference between the position of rotationally and pressure supported dEs, both deviate from the relations of massive early-type galaxies in the direction of dwarf spheroidal systems (dSphs). We have used their offset with respect to the Fundamental Plane of E/S0 galaxies to estimate their dark matter fraction. All the properties studied in this work agree with a ram pressure stripping scenario, where late-type galaxies infall into the cluster, their interaction with the intergalactic medium blows away their gas and, as a result, they are quenched in a small amount of time. However, those dEs in the center of the cluster seem to have been fully transformed leaving no trace of their possible spiral origin, thus, if that is the case, they must have experienced a more violent mechanism in combination with ram pressure stripping.

Effects of hierarchical features on longevity of submerged superhydrophobic surfaces with parallel grooves

NASA Astrophysics Data System (ADS)

Hemeda, A. A.; Gad-el-Hak, M.; Tafreshi, H. Vahedi

2014-08-01

While the air-water interface over superhydrophobic surfaces decorated with hierarchical micro- or nanosized geometrical features have shown improved stability under elevated pressures, their underwater longevity—-the time that it takes for the surface to transition to the Wenzel state—-has not been studied. The current work is devised to study the effects of such hierarchical features on the longevity of superhydrophobic surfaces. For the sake of simplicity, our study is limited to superhydrophobic surfaces composed of parallel grooves with side fins. The effects of fins on the critical pressure—-the pressure at which the surface starts transitioning to the Wenzel state—-and longevity are predicted using a mathematical approach based on the balance of forces across the air-water interface. Our results quantitatively demonstrate that the addition of hierarchical fins significantly improves the mechanical stability of the air-water interface, due to the high advancing contact angles that can be achieved when an interface comes in contact with the fins sharp corners. For longevity on the contrary, the hierarchical fins were only effective at hydrostatic pressures below the critical pressure of the original smooth-walled groove. Our results indicate that increasing the length of the fins decreases the critical pressure of a submerged superhydrophobic groove but increases its longevity. Increasing the thickness of the fins can improve both the critical pressure and longevity of a submerged groove. The mathematical framework presented in this paper can be used to custom-design superhydrophobic surfaces for different applications.

Resolution of ray-finned fish phylogeny and timing of diversification.

PubMed

Near, Thomas J; Eytan, Ron I; Dornburg, Alex; Kuhn, Kristen L; Moore, Jon A; Davis, Matthew P; Wainwright, Peter C; Friedman, Matt; Smith, W Leo

2012-08-21

Ray-finned fishes make up half of all living vertebrate species. Nearly all ray-finned fishes are teleosts, which include most commercially important fish species, several model organisms for genomics and developmental biology, and the dominant component of marine and freshwater vertebrate faunas. Despite the economic and scientific importance of ray-finned fishes, the lack of a single comprehensive phylogeny with corresponding divergence-time estimates has limited our understanding of the evolution and diversification of this radiation. Our analyses, which use multiple nuclear gene sequences in conjunction with 36 fossil age constraints, result in a well-supported phylogeny of all major ray-finned fish lineages and molecular age estimates that are generally consistent with the fossil record. This phylogeny informs three long-standing problems: specifically identifying elopomorphs (eels and tarpons) as the sister lineage of all other teleosts, providing a unique hypothesis on the radiation of early euteleosts, and offering a promising strategy for resolution of the "bush at the top of the tree" that includes percomorphs and other spiny-finned teleosts. Contrasting our divergence time estimates with studies using a single nuclear gene or whole mitochondrial genomes, we find that the former underestimates ages of the oldest ray-finned fish divergences, but the latter dramatically overestimates ages for derived teleost lineages. Our time-calibrated phylogeny reveals that much of the diversification leading to extant groups of teleosts occurred between the late Mesozoic and early Cenozoic, identifying this period as the "Second Age of Fishes."

Dynamics of zebrafish fin regeneration using a pulsed SILAC approach.

PubMed

Nolte, Hendrik; Hölper, Soraya; Housley, Michael P; Islam, Shariful; Piller, Tanja; Konzer, Anne; Stainier, Didier Y R; Braun, Thomas; Krüger, Marcus

2015-02-01

The zebrafish owns remarkable regenerative capacities allowing regeneration of several tissues, including the heart, liver, and brain. To identify protein dynamics during fin regeneration we used a pulsed SILAC approach that enabled us to detect the incorporation of (13) C6 -lysine (Lys6) into newly synthesized proteins. Samples were taken at four different time points from noninjured and regrowing fins and incorporation rates were monitored using a combination of single-shot 4-h gradients and high-resolution tandem MS. We identified more than 5000 labeled proteins during the first 3 weeks of fin regeneration and were able to monitor proteins that are responsible for initializing and restoring the shape of these appendages. The comparison of Lys6 incorporation rates between noninjured and regrowing fins enabled us to identify proteins that are directly involved in regeneration. For example, we observed increased incorporation rates of two actinodin family members at the actinotrichia, which is a hairlike fiber structure at the tip of regrowing fins. Moreover, we used quantitative real-time RNA measurements of several candidate genes, including osteoglycin, si:ch211-288h17.3, and prostaglandin reductase 1 to correlate the mRNA expression to Lys6 incorporation data. This novel pulsed SILAC methodology in fish can be used as a versatile tool to monitor newly synthesized proteins and will help to characterize protein dynamics during regenerative processes in zebrafish beyond fin regeneration. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fin propulsion on a human-powered submarine

NASA Astrophysics Data System (ADS)

Anderson, Iain A.; Pocock, Benjamin; Harbuz, Antoni; Algie, Cam; Vochezer, Daniel; Chao, Ryan; Lu, Benjamin

2015-03-01

Nearly all surface and underwater vessels are driven by screw propulsion; ideal for coupling to rotary engines and well understood after over a century of development. But most aquatic creatures use fins for swimming. Although there are sound evolutionary reasons why fish have fins and not propellers, they are nevertheless agile, fast and efficient. Although fish-like robots such as the MIT Robotuna are providing good insight into fin-based swimming there are advantages for using humans in the experimental device. Like an airplane test pilot they can write crash reports. We present preliminary observations for the human powered finned submarine: Taniwha. The sub participated in the 2nd European International Submarine races in Gosport UK where it received a trophy for "Best Non-Propeller Performance". Two sets of Hobie Mirage fin drives fixed to the upper and lower rear surfaces of the sub are pedaled by the pilot. The pilot also has two levers at the front, one to pitch a pair of dive planes and one for yawing a large rudder. Good speed, we estimate to be greater than 6 m/s is possible with these fins although we haven't explored their full potential. Straying too near the surface or bottom can lead to an instability, synonymous to a stall, such that control is lost. The mechanism for this will be discussed and solutions offered. Fish are 400 million years in front of us but one day we'll catch them.

Macropharyngodon pakoko, a new species of wrasse (Teleostei: Labridae) endemic to the Marquesas Islands, French Polynesia.

PubMed

Delrieu-Trottin, Erwan; Williams, Jeffrey T; Planes, Serge

2014-08-29

A new species of wrasse, Macropharyngodon pakoko, is described from the Marquesas Islands, bringing the total number of species of the genus Macropharyngodon to 12. Macropharyngodon pakoko was found at depths from 0-42 m and is endemic to the Marquesas Islands. Macropharyngodon pakoko is similar to M. meleagris, which is widely distributed from the central and western Pacific to Cocos-Keeling in the Indian Ocean, but differs genetically and in several coloration characters: males with irregularly curved black humeral blotch with incomplete iridescent blue border; inverted irregular "U"- shaped band on the cheek; a small black spot at the upper base of the pectoral fin; and background color of the body greenish with faint bluish black spots on each scale. Females lack black pigment on the chest posterior to the ventral attachment of the gill membranes; reddish black blotches on the body are widely spaced, particularly on the head where they are more reddish and half the size of those on body; caudal fin with small, bright yellow spots arranged in narrow vertical bands with pale interspaces; pelvic fins pale with three reddish yellow cross-bands; a small black spot at the upper base of the pectoral fin; and small reddish spots along the base of the anal fin. Juveniles have irregular black blotches on the body, a small black spot instead of an ocellus posteriorly on the dorsal fin and lack large black spots and ocellus on the anal fin. 

Resolution of ray-finned fish phylogeny and timing of diversification

PubMed Central

Near, Thomas J.; Eytan, Ron I.; Dornburg, Alex; Kuhn, Kristen L.; Moore, Jon A.; Davis, Matthew P.; Wainwright, Peter C.; Friedman, Matt; Smith, W. Leo

2012-01-01

Ray-finned fishes make up half of all living vertebrate species. Nearly all ray-finned fishes are teleosts, which include most commercially important fish species, several model organisms for genomics and developmental biology, and the dominant component of marine and freshwater vertebrate faunas. Despite the economic and scientific importance of ray-finned fishes, the lack of a single comprehensive phylogeny with corresponding divergence-time estimates has limited our understanding of the evolution and diversification of this radiation. Our analyses, which use multiple nuclear gene sequences in conjunction with 36 fossil age constraints, result in a well-supported phylogeny of all major ray-finned fish lineages and molecular age estimates that are generally consistent with the fossil record. This phylogeny informs three long-standing problems: specifically identifying elopomorphs (eels and tarpons) as the sister lineage of all other teleosts, providing a unique hypothesis on the radiation of early euteleosts, and offering a promising strategy for resolution of the “bush at the top of the tree” that includes percomorphs and other spiny-finned teleosts. Contrasting our divergence time estimates with studies using a single nuclear gene or whole mitochondrial genomes, we find that the former underestimates ages of the oldest ray-finned fish divergences, but the latter dramatically overestimates ages for derived teleost lineages. Our time-calibrated phylogeny reveals that much of the diversification leading to extant groups of teleosts occurred between the late Mesozoic and early Cenozoic, identifying this period as the “Second Age of Fishes.” PMID:22869754

New record of Japanese snake blenny Xiphasia matsubarai (Perciformes: Blenniidae) from South China Sea

NASA Astrophysics Data System (ADS)

Yi, Murong; Zhao, Chunxu; Su, Xin; Tao, Yajin; Yan, Yunrong

2017-11-01

Specimens belonging to the family Blenniidae were collected in a fishery resource investigation from the coastal waters of Xisha Islands and Hainan Island, South China Sea in 2016. Combining morphological results with sequence analysis, we identified one specimen as Xiphasia matsubarai Okada & Suzuki, 1952. This represents a new record in the South China Sea. In morphology, the specimen has the following traits: body elongated, eel-like or ribbon-like in shape; flanks medium flat; the head small bluntly rounded anteriorly and without a moustache; eyes is slightly smaller, on upper lateral position of head, which is about equal to 1/5 of the length of the head; body without scales, lateral line has been degraded; both sides of the upper and lower jaws with a canine; gill is opening at the top of the pectoral fin base, approximately equal to the length of eye diameter. Dorsal fin XI, 96; pectoral fin 10; anal fin II, 95. Head and body grey-brown, including 26 dark grey-brown bands; abdomen and lower operculum yellowish grey and colour lighter; and dorsal base long with dark grey. Origin of dorsal is located over the anterior margin of pupil; black blotch on dorsal fin between 8th and 10th dorsal spine; anal and caudal fins dark grey, pectoral and ventral fins pale yellow. Sequence analysis of cytochrome oxidase subunit I gene (COI) strongly supports the identity of the specimen as X. matsubarai.

Approximate strip exchanging.

PubMed

Roy, Swapnoneel; Thakur, Ashok Kumar

2008-01-01

Genome rearrangements have been modelled by a variety of primitives such as reversals, transpositions, block moves and block interchanges. We consider such a genome rearrangement primitive Strip Exchanges. Given a permutation, the challenge is to sort it by using minimum number of strip exchanges. A strip exchanging move interchanges the positions of two chosen strips so that they merge with other strips. The strip exchange problem is to sort a permutation using minimum number of strip exchanges. We present here the first non-trivial 2-approximation algorithm to this problem. We also observe that sorting by strip-exchanges is fixed-parameter-tractable. Lastly we discuss the application of strip exchanges in a different area Optical Character Recognition (OCR) with an example.

MOCHA - Multi-Study Ocean Acoustics Human Effects Analysis

DTIC Science & Technology

2014-09-30

and P.J.O. Miller. 2014. High thresholds for avoidance of sonar by free-ranging long-finned pilot whales (Globicephala melas ). Marine Pollution...sonar by free-ranging long-finned pilot whales (Globicephala melas ). Marine Pollution Bulletin, 83(1): 165-180. [published, refereed] DeRuiter, S.L...Press. The social context of individual foraging behaviour in long-finned pilot whales (Globicephala melas ). Behaviour, 2014 [in press, refereed

Structure and mechanical implications of the pectoral fin skeleton in the Longnose Skate (Chondrichthyes, Batoidea).

PubMed

Huang, Wei; Hongjamrassilp, Watcharapong; Jung, Jae-Young; Hastings, Philip A; Lubarda, Vlado A; McKittrick, Joanna

2017-03-15

Animal propulsion systems are believed to show high energy and mechanical efficiency in assisting movement compared to artificial designs. As an example, batoid fishes have very light cartilaginous skeletons that facilitate their elegant swimming via enlarged wing-like pectoral fins. The aim of this work is to illustrate the hierarchical structure of the pectoral fin of a representative batoid, the Longnose Skate (Raja rhina), and explain the mechanical implications of its structural design. At the macro level, the pectoral fins are comprised of radially oriented fin rays, formed by staggered mineralized skeletal elements stacked end-to-end. At the micro level, the midsection of each radial element is composed of three mineralized components, which consist of discrete segments (tesserae) that are mineralized cartilage and embedded in unmineralized cartilage. The radial elements are wrapped with aligned, unmineralized collagen fibers. This is the first report of the detailed structure of the ray elements, including the observation of a 3-chain mineralized tesserae. Structural analyses demonstrate that this configuration enhances stiffness in multiple directions. A two-dimensional numerical model based on the morphological analysis demonstrated that the tessera structure helps distributing shear, tensile and compressive stress more ideally, which can better support both lift and thrust forces when swimming without losing flexibility. Batoid fishes have very light cartilaginous skeletons that facilitate their elegant swimming by applying their enlarged wing-like pectoral fins. Previous studies have shown structural features and mechanical properties of the mineralized cartilage skeleton in various batoid fishes. However, the details of the pectoral fin structure at different length scales, as well as the relationship between the mechanical properties and structural design remains unknown. The present work illustrates the hierarchical structure of the pectoral fin of the Longnose Skate (a representative batoid fish) and verifies the materials configuration and structural design increases the stiffness of fin skeleton without a loss in flexibility. These results have implications for the design of strong but flexible materials and bio-inspired autonomous underwater vehicles (AUVs). Copyright © 2017 Acta Materialia Inc. All rights reserved.

Skeletal development and abnormalities of the vertebral column and of the fins in hatchery-reared turbot Scophthalmus maximus.

PubMed

Tong, X H; Liu, Q H; Xu, S H; Ma, D Y; Xiao, Z Z; Xiao, Y S; Li, J

2012-03-01

To describe the skeletal development and abnormalities in turbot Scophthalmus maximus, samples were collected every day from hatching to 60 days after hatching (DAH). A whole-mount cartilage and bone-staining technique was used. Vertebral ontogeny started with the formation of anterior haemal arches at 5·1 mm standard length (L(S) ) c. 11 DAH, and was completed by the full attainment of parapophyses at 16·9 mm L(S) c. 31 DAH. Vertebral centra started to develop at 6·3 mm L(S) c. 16 DAH and ossification in all centra was visible at 11·0 mm L(S) c. 25 DAH. The caudal fin appeared at 5·1 mm L(S) c. 11 DAH and ossification was visible at 20·6 mm L(S) c. 37 DAH. The onset of dorsal and anal fin elements appeared at 5·8 mm L(S) c. 15 DAH and 6·3 mm L(S) c. 16 DAH, respectively. Ossifications of both dorsal fin and anal fin were visible at 20·6 mm L(S) c. 37 DAH. The pectorals were the only fins present before first feeding, their ossifications were completed at 23·5 mm L(S) c. 48 DAH. Pelvic fins began forming at 7·2 mm L(S) c. 19 DAH and calcification of the whole structure was visible at 19·8 mm L(S) c. 36 DAH. In the present study, 24 types of skeletal abnormalities were observed. About 51% of individuals presented skeletal abnormalities, and the highest occurrence was found in the haemal region of the vertebral column. As for each developmental stage, the most common abnormalities were in the dorsal fin during early metamorphic period (stage 2), vertebral fusion during climax metamorphosis (stage 3) and caudal fin abnormality during both late-metamorphic period (stage 4) and post-metamorphic period (stage 5). Such research will be useful for early detection of skeletal malformations during different growth periods of reared S. maximus. © 2012 The Authors. Journal of Fish Biology © 2012 The Fisheries Society of the British Isles.

Abell 1367: a high fraction of late-type galaxies displaying H I morphological and kinematic perturbations

NASA Astrophysics Data System (ADS)

Scott, T. C.; Brinks, E.; Cortese, L.; Boselli, A.; Bravo-Alfaro, H.

2018-04-01

To investigate the effects the cluster environment has on late-type galaxies (LTGs), we studied H I perturbation signatures for all Abell 1367 LTGs with H I detections. We used new Very Large Array H I observations combined with AGES single-dish blind survey data. Our study indicates that the asymmetry between the high- and low-velocity wings of the characteristic double-horn-integrated H I spectrum as measured by the asymmetry parameter, A_{flux}, can be a useful diagnostic for ongoing and/or recent H I stripping. 26 per cent of A1367 LTGs have an A_{flux} ratio, more asymmetrical than 3 times the 1σ spread in the A_{flux} ratio distribution of an undisturbed sample of isolated galaxies (2 per cent) and samples from other denser environments (10 per cent-20 per cent). Over half of the A1367 LTGs, which are members of groups or pairs, have an A_{flux} ratio larger than twice the 1σ spread found in the isolated sample. This suggests intergroup/pair interactions could be making a significant contribution to the LTGs displaying such A_{flux} ratios. The study also demonstrates that the definition of the H I offset from the optical centre of LTGs is resolution dependent, suggesting that unresolved AGES H I offsets that are significantly larger than the pointing uncertainties (>2σ), reflect interactions which have asymmetrically displaced, significant masses of lower density H I, while having minimal impact on the location of the highest density H I in resolved maps. The distribution of A_{flux} from a comparable sample of Virgo galaxies provides a clear indication that the frequency of H I profile perturbations is lower than in A1367.

Drought offset ecological restoration program-induced increase in vegetation activity in the Beijing-Tianjin Sand Source Region, China.

PubMed

Wu, Zhitao; Wu, Jianjun; He, Bin; Liu, Jinghui; Wang, Qianfeng; Zhang, Hong; Liu, Yong

2014-10-21

To improve the ecological conditions, the Chinese government adopted six large-scale ecological restoration programs including 'Three-North Shelterbelt Project', "Grain for Green Project" and "Beijing-Tianjin Sand Source Control Project". Meanwhile, these ecologically vulnerable areas have experienced frequent droughts. However, little attention has been paid to the impact of drought on the effectiveness of these programs. Taking Beijing-Tianjin Sand Source Region (BTSSR) as study area, we investigated the role of droughts and ecological restoration program on trends of vegetation activities and to address the question of a possible "drought signal" in assessing effectiveness of ecological restoration program. The results demonstrate the following: (1) Vegetation activity increased in the BTSSR during 2000-2010, with 58.44% of the study area showing an increased NDVI, of which 11.80% had a significant increase at 0.95 confidential level. The decreasing NDVI trends were mainly concentrated in a southwest-to-northeast strip in the study area. (2) Drought was the main driving force for a decreasing trend of vegetation activity in the southwest-to-northeast regions of the BTSSR at the regional and spatial scales. Summer droughts in 2007 and 2009 contributed to the decreasing trend in NDVI. The severe and extreme droughts in summer reduced the NDVI by approximately 13.06% and 23.55%, respectively. (3) The residual analysis result showed that human activities, particularly the ecological restoration programs, have a positive impact on vegetation change. Hence, the decreasing trends in the southwest-to-northeast regions of the BTSSR cannot be explained by the improper ecological restoration program and is partly explained by droughts, especially summer droughts. Therefore, drought offset the ecological restoration program-induced increase in vegetation activity in the BTSSR.

Defining the minimal structural requirements for partial agonism at the type I myo-inositol 1,4,5-trisphosphate receptor.

PubMed

Wilcox, R A; Fauq, A; Kozikowski, A P; Nahorski, S R

1997-02-03

The novel synthetic analogues D-3-fluoro-myo-inositol 1,5-bisphosphate-4-phosphorothioate, [3F-Ins(1,5)P2-4PS], D-3-fluoro-myo-inositol 1,4-bisphosphate-5-phosphorothioate [3F-Ins(1,4)P2-5PS], and D-3-fluoro-myo-inositol 1-phosphate-4,5-bisphosphorothioate [3F-Ins(1)P-(4,5)PS2] were utilised to define the structure-activity relationships which could produce partial agonism at the Ca2+ mobilising myo-inositol 1,4,5-trisphosphate [Ins(1,4,5)P3] receptor. Based on prior structure-activity data we hypothesised that the minimal structural requirements for lns(1,4,5)P3 receptor partial agonism, were phosphorothioate substitution of the crucial vicinal 4,5-bisphosphate pair accompanied by another structural perturbation, such fluorination of 3-position of the myo-inositol ring. All the analogues fully displaced [3H]Ins(1,4,5)P3 from a single Ins(1,4,5)P3 binding site in pig cerebellar membranes [3F-Ins(1,5)P2-4PS (1C50 = 26 nM), 3F-Ins(1,4)P2-5PS (IC50 = 80 nM) and 3F-Ins(1)P-(4,5)PS2 (IC50 = 109 nM) cf. Ins(1,4,5)P3 (IC50 = 11 nM)]. In contrast, 3F-Ins(1,5)P2-4PS (IC50 = 424 nM) and 3F-Ins(1,4)P2-5PS (IC50 = 3579 nM) were weak full agonists at the Ca2+ mobilising Ins(1,4,5)P3 receptor of permeabilised SH-SY5Y neuroblastoma cells, being respectively 4- and 36-fold less potent than Ins(1,4,5)P3 (EC50 = 99 nM). While 3F-Ins(1)P-(4,5)PS2 (EC50 = 11345 nM) was a partial agonist releasing only 64.3 +/- 1.9% of the Ins(1,4,5)P3-sensitive intracellular Ca2+ pools. 3F-Ins(1)P-(4,5)PS2 was unique among the Ins(1,4,5)P3 receptor partial agonists so far identified in having a relatively high affinity for the Ins(1,4,5)P3 binding site, accompanied by a significant loss of intrinsic activity for Ca2+ mobilisation. This improved affinity was probably due to the retention of the 1-position phosphate, which enhances interaction with the Ins-(1,4,5)P3 receptor. 3F-Ins(1)P-(4,5)PS2 may be an important lead compound for the development of efficient Ins(1,4,5)P3 receptor antagonists.

Average-passage simulation of counter-rotating propfan propulsion systems as applied to cruise missiles

NASA Technical Reports Server (NTRS)

Mulac, Richard A.; Schneider, Jon C.; Adamczyk, John J.

1989-01-01

Counter-rotating propfan (CRP) propulsion technologies are currently being evaluated as cruise missile propulsion systems. The aerodynamic integration concerns associated with this application are being addressed through the computational modeling of the missile body-propfan flowfield interactions. The work described in this paper consists of a detailed analysis of the aerodynamic interactions between the control surfaces and the propfan blades through the solution of the average-passage equation system. Two baseline configurations were studied, the control fins mounted forward of the counter-rotating propeller and the control fins mounted aft of the counter-rotating propeller. In both cases, control fin-propfan separation distance and control fin deflection angle were varied.

F-100 and F-100A on ramp - comparison showing tail modifications that solved control problems during

NASA Technical Reports Server (NTRS)

1955-01-01

On the left is NACA High-Speed Flight Station's North American F-100A (52-5778) Super Sabre with a modified vertical fin. On the right is an Air Force's North American F-100A (52-5773) with the original vertical fin configuration. 1955. NACA added a larger vertical fin to the airplane in December 1954, adding 10 percent more surface area. Later North American installed an even larger fin, having 27 percent greater area, as well as wingtip extensions. The modifications solved the dangerous directional stability and roll coupling problems that the F-100 was experiencing. The F-100 series went on to a long and distinguished service life.

A new species of the genus Triplophysa (Cypriniformes: Nemacheilidae), Triplophysa daochengensis, from Sichuan Province, China

PubMed Central

WU, Yu-Yi; SUN, Zhi-Yu; GUO, Yan-Shu

2016-01-01

Triplophysa daochengensis sp. nov. is described from the Daocheng River, a northern tributary of the Jinsha River in Sichuan Province, China. The new species can be distinguished from its congeners by the following characters: body smooth and scales absent; lateral line complete; caudal peduncle compressed, depth unchanging; head length equal to caudal-peduncle length; lower jaw shovel-shaped; dorsal-fin origin anterior to pelvic-fin origin and closer to the tip of the snout than to the caudal-fin base, last unbranched ray hard; pelvic-fin tip not reaching anus; posterior chamber of gas bladder absent; intestine of spiral type with three winding coils. PMID:27686788

Thrust Production and Wake Structure of a Batoid-Inspired Oscillating Fin

NASA Astrophysics Data System (ADS)

Clark, Richard

2005-11-01

Experiments are reported on the hydrodynamic performance of a flexible fin. The fin replicates some features of the pectoral fin of a batoid fish (such as a ray or skate) in that it is actuated in a traveling wave motion, with the amplitude of the motion increasing linearly along the span from root to tip. Thrust is found to increase with non-dimensional frequency, and an optimal oscillatory gait is identified. Power consumption measurements lead to the computation of Froude efficiency, and an optimal efficiency condition is evaluated. Wake visualizations are presented, and a vortex model of the wake near zero net thrust is suggested. Strouhal number effects on the wake topology are also illustrated.

Thrust production and wake structure of a batoid-inspired oscillating fin

NASA Astrophysics Data System (ADS)

Clark, R. P.; Smits, A. J.

2006-09-01

Experiments are reported on the hydrodynamic performance of a flexible fin. The fin replicates some features of the pectoral fin of a batoid fish (such as a ray or skate) in that it is actuated in a travelling wave motion, with the amplitude of the motion increasing linearly along the span from root to tip. Thrust is found to increase with non-dimensional frequency, and an optimal oscillatory gait is identified. Power consumption measurements lead to the computation of propulsive efficiency, and an optimal efficiency condition is evaluated. Wake visualizations are presented, and a vortex model of the wake near zero net thrust is suggested. Strouhal number effects on the wake topology are also illustrated.

Wake topology of under-actuated rajiform batoid robots

NASA Astrophysics Data System (ADS)

Valdivia Y Alvarado, Pablo; Weymouth, Gabriel; Thekoodan, Dilip; Patrikalakis, Nicholas

2011-11-01

Under-actuated continuous soft robots are designed to have modes of vibration that match desired body motions using minimal actuation. The desired modes of vibration are enabled by flexible continuous bodies with heterogenous material distributions. Errors or intentional approximations in the manufactured material distributions alter the achieved body motions and influence the resulting locomotion performance. An under-actuated continuous soft robot designed to mimic rajiform batoids such as stingrays is used to investigate the influence that fin kinematics variations have on wake topology, and the trade-offs that simplifying the body material structure has on achievable swimming performance. Pectoral fin kinematics in rajiform batoids are defined by traveling waves along the fin cord with particular amplitude envelopes along both the fin cord and span. Digital particle image velocimetry (DPIV) analysis of a prototype's wake structure and immersed-boundary numerical simulations are used to clarify the role of traveling wave wavelength, fin flapping frequency, and amplitude envelope characteristics on the resulting wake topology and swimming performance.

YF-12 Lockalloy ventral fin program, volume 1. [design analysis, fabrication, and manufacturing of aircraft structures using aluminum and beryllium alloys for the lockheed YF-12 aircraft

NASA Technical Reports Server (NTRS)

Duba, R. J.; Haramis, A. C.; Marks, R. F.; Payne, L.; Sessing, R. C.

1976-01-01

Results are presented of the YF-12 Lockalloy Ventral Fin Program which was carried out by Lockheed Aircraft Corporation - Advanced Development Projects for the joint NASA/USAF YF-12 Project. The primary purpose of the program was to redesign and fabricate the ventral fin of the YF-12 research airplane (to reduce flutter) using Lockalloy, and alloy of beryllium and aluminum, as a major structural material. A secondary purpose, was to make a material characterization study (thermodynamic properties, corrosion; fatigue tests, mechanical properties) of Lockalloy to validate the design of the ventral fin and expand the existing data base on this material. All significant information pertinent to the design and fabrication of the ventral fin is covered. Emphasis throughout is given to Lockalloy fabrication and machining techniques and attendant personnel safety precautions. Costs are also examined. Photographs of tested alloy specimens are shown along with the test equipment used.

The Prx1 limb enhancers: targeted gene expression in developing zebrafish pectoral fins.

PubMed

Hernández-Vega, Amayra; Minguillón, Carolina

2011-08-01

Limbs represent an excellent model to study the induction, growth, and patterning of several organs. A breakthrough to study gene function in various tissues has been the characterization of regulatory elements that allow tissue-specific interference of gene function. The mouse Prx1 promoter has been used to generate limb-specific mutants and overexpress genes in tetrapod limbs. Although zebrafish possess advantages that favor their use to study limb morphogenesis, there is no driver described suitable for specifically interfering with gene function in developing fins. We report the generation of zebrafish lines that express enhanced green fluorescent protein (EGFP) driven by the mouse Prx1 enhancer in developing pectoral fins. We also describe the expression pattern of the zebrafish prrx1 genes and identify three conserved non-coding elements (CNEs) that we use to generate fin-specific EGFP reporter lines. Finally, we show that the mouse and zebrafish regulatory elements may be used to modify gene function in pectoral fins. Copyright © 2011 Wiley-Liss, Inc.

Aerodynamics of an Axisymmetric Missile Concept Having Cruciform Strakes and In-Line Tail Fins From Mach 0.60 to 4.63

NASA Technical Reports Server (NTRS)

Allen, Jerry M.

2005-01-01

An experimental study has been performed to develop a large force and moment aerodynamic data set on a slender axisymmetric missile configuration having cruciform strakes and in-line control tail fins. The data include six-component balance measurements of the configuration aerodynamics and three-component measurements on all four tail fins. The test variables include angle of attack, roll angle, Mach number, model buildup, strake length, nose size, and tail fin deflection angles to provide pitch, yaw, and roll control. Test Mach numbers ranged from 0.60 to 4.63. The entire data set is presented on a CD-ROM that is attached to this paper. The CD-ROM also includes extensive plots of both the six-component configuration data and the three-component tail fin data. Selected samples of these plots are presented in this paper to illustrate the features of the data and to investigate the effects of the test variables.

Aerodynamics of an Axisymmetric Missile Concept Having Cruciform Strakes and In-Line Tail Fins From Mach 0.60 to 4.63, Supplement

NASA Technical Reports Server (NTRS)

Allen, Jerry M.

2005-01-01

An experimental study has been performed to develop a large force and moment aerodynamic data set on a slender axisymmetric missile configuration having cruciform strakes and in-line control tail fins. The data include six-component balance measurements of the configuration aerodynamics and three-component measurements on all four tail fins. The test variables include angle of attack, roll angle, Mach number, model buildup, strake length, nose size, and tail fin deflection angles to provide pitch, yaw, and roll control. Test Mach numbers ranged from 0.60 to 4.63. The entire data set is presented on a CD-ROM that is attached to this paper. The CD-ROM also includes extensive plots of both the six-component configuration data and the three-component tail fin data. Selected samples of these plots are presented in this paper to illustrate the features of the data and to investigate the effects of the test variables.

Temporal separation of two fin whale call types across the eastern North Pacific.

PubMed

Sirović, Ana; Williams, Lauren N; Kerosky, Sara M; Wiggins, Sean M; Hildebrand, John A

2013-01-01

Fin whales ( Balaenoptera physalus ) produce a variety of low-frequency, short-duration, frequency-modulated calls. The differences in temporal patterns between two fin whale call types are described from long-term passive acoustic data collected intermittently between 2005 and 2011 at three locations across the eastern North Pacific: the Bering Sea, off Southern California, and in Canal de Ballenas in the northern Gulf of California. Fin whale calls were detected at all sites year-round, during all periods with recordings. At all three locations, 40-Hz calls peaked in June, preceding a peak in 20-Hz calls by 3-5 months. Monitoring both call types may provide a more accurate insight into the seasonal presence of fin whales across the eastern North Pacific than can be obtained from a single call type. The 40-Hz call may be associated with a foraging function, and temporal separation between 40- and 20-Hz calls may indicate the separation between predominately feeding behavior and other social interactions.

Cyanobacterial Neurotoxin β-N-Methylamino-L-alanine (BMAA) in Shark Fins

PubMed Central

Mondo, Kiyo; Hammerschlag, Neil; Basile, Margaret; Pablo, John; Banack, Sandra A.; Mash, Deborah C.

2012-01-01

Sharks are among the most threatened groups of marine species. Populations are declining globally to support the growing demand for shark fin soup. Sharks are known to bioaccumulate toxins that may pose health risks to consumers of shark products. The feeding habits of sharks are varied, including fish, mammals, crustaceans and plankton. The cyanobacterial neurotoxin β-N-methylamino-L-alanine (BMAA) has been detected in species of free-living marine cyanobacteria and may bioaccumulate in the marine food web. In this study, we sampled fin clips from seven different species of sharks in South Florida to survey the occurrence of BMAA using HPLC-FD and Triple Quadrupole LC/MS/MS methods. BMAA was detected in the fins of all species examined with concentrations ranging from 144 to 1836 ng/mg wet weight. Since BMAA has been linked to neurodegenerative diseases, these results may have important relevance to human health. We suggest that consumption of shark fins may increase the risk for human exposure to the cyanobacterial neurotoxin BMAA. PMID:22412816

Parallel Fin ORU Thermal Interface for space applications. [Orbital Replaceable Unit

NASA Technical Reports Server (NTRS)

Stobb, C. A.; Limardo, Jose G.

1992-01-01

The Parallel Fin Thermal Interface has been developed as an Orbital Replaceable Unit (ORU) interface. The interface transfers heat from an ORU baseplate to a Heat Acquisition Plate (HAP) through pairs of fins sandwiched between insert plates that press against the fins with uniform pressure. The insert plates are spread apart for ORU baseplate separation and replacement. Two prototype interfaces with different fin dimensions were built (Model 140 and 380). Interfacing surface samples were found to have roughnesses of 56 to 89 nm. Conductance values of 267 to 420 W/sq m C were obtained for the 140 model in vacuum with interface pressures of 131 to 262 kPa (19 to 38 psi). Vacuum conductances ranging from 176 to 267 W/sq m F were obtained for the 380 model at interface pressures of 97 to 152 kPa (14 and 22 psi). Correlations from several sources were found to agree with test data within 20 percent using thermal math models of the interfaces.

TNF signaling and macrophages govern fin regeneration in zebrafish larvae.

PubMed

Nguyen-Chi, Mai; Laplace-Builhé, Béryl; Travnickova, Jana; Luz-Crawford, Patricia; Tejedor, Gautier; Lutfalla, Georges; Kissa, Karima; Jorgensen, Christian; Djouad, Farida

2017-08-10

Macrophages are essential for appendage regeneration after amputation in regenerative species. The molecular mechanisms through which macrophages orchestrate blastema formation and regeneration are still unclear. Here, we use the genetically tractable and transparent zebrafish larvae to study the functions of polarized macrophage subsets during caudal fin regeneration. After caudal fin amputation, we show an early and transient accumulation of pro-inflammatory macrophages concomitant with the accumulation of non-inflammatory macrophages which, in contrast to pro-inflammatory macrophages, remain associated to the fin until the end of the regeneration. Chemical and genetic depletion of macrophages suggested that early recruited macrophages that express TNFα are critical for blastema formation. Combining parabiosis and morpholino knockdown strategies, we show that TNFα/TNFR1 signaling pathway is required for the fin regeneration. Our study reveals that TNFR1 has a necessary and direct role in blastema cell activation suggesting that macrophage subset balance provides the accurate TNFα signal to prime regeneration in zebrafish.

Hydrodynamic optimality of balistiform and gymnotiform locomotion

NASA Astrophysics Data System (ADS)

Sprinkle, Brennan; Bale, Rahul; Bhalla, Amneet Pal Singh; MacIver, Malcolm A.; Patankar, Neelesh A.

2017-03-01

Some groups of fish have evolved to generate propulsion using undulatory elongated fins while maintaining a relatively rigid body. The fins run along the body axis and can be dorsal, ventral, dorsoventral pairs or left-right pairs. These fish are termed as median/paired fin (MPF) swimmers. The movement of these groups of fish was studied in an influential series of papers by Lighthill and Blake. In this work, we revisit this problem by performing direct numerical simulations. We interrogate two issues. First, we investigate and explain a key morphological feature, which is the diagonal fin insertion found in many MPF swimmers such as the knifefish. Not only are these results of biological relevance, but these are also useful in engineering to design bioinspired highly maneuverable underwater vehicles. Second, we investigate whether there is a mechanical advantage in the form of reduced cost of transport (COT) (energy spent per unit distance traveled) for not undulating the entire body. We find that a rigid body attached to an undulating fin leads to a reduced COT.

Hydrodynamic aspects of thrust generation in gymnotiform swimming

NASA Astrophysics Data System (ADS)

Shirgaonkar, Anup A.; Curet, Oscar M.; Patankar, Neelesh A.; Maciver, Malcolm A.

2008-11-01

The primary propulsor in gymnotiform swimmers is a fin running along most of the ventral midline of the fish. The fish propagates traveling waves along this ribbon fin to generate thrust. This unique mode of thrust generation gives these weakly electric fish great maneuverability cluttered spaces. To understand the mechanical basis of gymnotiform propulsion, we investigated the hydrodynamics of a model ribbon-fin of an adult black ghost knifefish using high-resolution numerical experiments. We found that the principal mechanism of thrust generation is a central jet imparting momentum to the fluid with associated vortex rings near the free edge of the fin. The high-fidelity simulations also reveal secondary vortex rings potentially useful in rapid sideways maneuvers. We obtained the scaling of thrust with respect to the traveling wave kinematic parameters. Using a fin-plate model for a fish, we also discuss improvements to Lighthill's inviscid theory for gymnotiform and balistiform modes in terms of thrust magnitude, viscous drag on the body, and momentum enhancement.

The Center for Regenerative Biology and Medicine at Mount Desert Island Biological Laboratory

DTIC Science & Technology

2014-06-01

Positional Memory Code Axolotl 15. SUBJECT TERMS microRNAs Zebrafish Polypterus 16...miR-7a, let-7j, miR-130c, miR-338, miR-204 and miR- 2184 that are shared between regenerating axolotl forelimbs, zebrafish caudal fins and...regeneration was defective in both zebrafish and Polypterus fin appendages and axolotl limbs (Fig. 1, 2). Polypterus caudal and pectoral fins

Large Scale Density Estimation of Blue and Fin Whales (LSD)

DTIC Science & Technology

2014-09-30

172. McDonald, MA, Hildebrand, JA, and Mesnick, S (2009). Worldwide decline in tonal frequencies of blue whale songs . Endangered Species Research 9...1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Large Scale Density Estimation of Blue and Fin Whales ...estimating blue and fin whale density that is effective over large spatial scales and is designed to cope with spatial variation in animal density utilizing

Options for Hardening FinFETS with Flowable Oxide Between Fins

DTIC Science & Technology

2017-03-01

thus hardening by process is needed. Using the methodology of CV measurements on inexpensive experimental blanket oxides we have determined options...NY 10598 Abstract: A methodology using radiation-induced charge measurements by CV techniques on blanket oxides is shown to aid in the choice...of process options for hardening FinFETs. Net positive charge in flowable oxides was reduced by 50 % using a simple non -intrusive process change

Finite Element Approach for the Design of Control Algorithms for Vertical Fin Buffeting Using Strain Actuation

DTIC Science & Technology

2001-06-01

Algorithms for Vertical Fin Buffeting Using Strain Actuation DISTRIBUTION: Approved for public release, distribution unlimited This paper is part of the...UNCLASSIFIED 8-1 Finite Element Approach for the Design of Control Algorithms for Vertical Fin Buffeting Using Strain Actuation Fred Nitzsche...groups), the disturbance (buffet load), and the two output variables (a choice among four Introduction accelerometers and five strain - gauge positions

Wind tunnel test results for the direction controlled antitank DCAT missile at Mach numbers from 0.64 to 2.50

NASA Technical Reports Server (NTRS)

Martin, T. A.; Spring, D. J.

1973-01-01

Wind tunnel test results are presented to show aerodynamic characteristics over the Mach number range of 0.64 to 2.50 of the DCAT missile. Data are presented showing the interference created by the rear mounted reaction control system. Two candidate fins were installed on the model during tests: a flat folding fin and a curved wrap around fin.

Anatomy and evolution of heterocercal tail in lamniform sharks.

PubMed

Kim, Sun H; Shimada, Kenshu; Rigsby, Cynthia K

2013-03-01

Lamniformes is a small shark group consisting of 15 extant species with remarkably diverse lifestyles and a wide range in heterocercal tail morphology. The caudal fin morphology must be related to their lifestyle because the tail is a main locomotive structure in sharks, but such relationships have remained largely uninvestigated. Here, the morphology-lifestyle relationship in lamniforms is examined through phylogenetic mapping. This study suggests that, within Lamniformes, caudal fins with a more horizontally directed curvature of the vertebral column are plesiomorphic, whereas those with a large dorsally directed curvature of the vertebral column are apomorphic. It also shows that caudal fins with posteriorly directed hypochordal rays are plesiomorphic, and that those with ventrally directed hypochordal rays are apomorphic within Lamniformes. Four basic caudal fin types are recognized in lamniforms on the basis of these skeletal variables in which one corollary is that the evolution of external morphology of caudal fin does not necessarily correspond to the evolution of its skeletal anatomy. This study also demonstrates that specific lifestyles seen in different lamniforms are indeed correlative with different caudal fin types in which a less asymmetrical heterocercal tail is a derived feature in lamniforms that evolved for fast swimming to capture fast swimming prey. Copyright © 2013 Wiley Periodicals, Inc.

Evolutionary multiobjective design of a flexible caudal fin for robotic fish.

PubMed

Clark, Anthony J; Tan, Xiaobo; McKinley, Philip K

2015-11-25

Robotic fish accomplish swimming by deforming their bodies or other fin-like appendages. As an emerging class of embedded computing system, robotic fish are anticipated to play an important role in environmental monitoring, inspection of underwater structures, tracking of hazardous wastes and oil spills, and the study of live fish behaviors. While integration of flexible materials (into the fins and/or body) holds the promise of improved swimming performance (in terms of both speed and maneuverability) for these robots, such components also introduce significant design challenges due to the complex material mechanics and hydrodynamic interactions. The problem is further exacerbated by the need for the robots to meet multiple objectives (e.g., both speed and energy efficiency). In this paper, we propose an evolutionary multiobjective optimization approach to the design and control of a robotic fish with a flexible caudal fin. Specifically, we use the NSGA-II algorithm to investigate morphological and control parameter values that optimize swimming speed and power usage. Several evolved fin designs are validated experimentally with a small robotic fish, where fins of different stiffness values and sizes are printed with a multi-material 3D printer. Experimental results confirm the effectiveness of the proposed design approach in balancing the two competing objectives.

A flow separation study over a shortfin mako shark pectoral fin

NASA Astrophysics Data System (ADS)

Bradshaw, Michael; Lang, Amy; Wahidi, Redha; Smith, Drew; Motta, Philip

2011-11-01

Many animals possess performance enhancing mechanisms, such as the denticles found on the skin of the shortfin mako shark (Isurus oxyrinchus). The shortfin mako, one of the fastest sharks on the planet, is covered by small, tooth-like scales that vary in bristling capability. Previous biological findings have shown that the scales increase in flexibility from the leading to trailing edge over the pectoral fin. As this fin is a primary control surface, the scale bristling may provide a mechanism for separation control that leads to decreased drag and increased maneuverability. Such findings can potentially lead to the development of similar micro-scale mechanisms to improve the efficiency of aerospace design. A left pectoral fin (71 cm span) was tested in a water tunnel facility under static and dynamic conditions. Digital Particle Image Velocimetry (DPIV) was used to characterize the flow over the fin. Various angles of attack at two speeds were tested (Re of 44,500 and 68,000). Two chord-wise locations, approximately mid-span where three-dimensional effects were minimized, were viewed to analyze the flow. After the initial testing, the fin was painted to eliminate the effect of the scales and retested to observe flow separation. Supported by REU SITE EEC grant number 1062611.

Gauging the threat: the first population estimate for white sharks in South Africa using photo identification and automated software.

PubMed

Towner, Alison V; Wcisel, Michelle A; Reisinger, Ryan R; Edwards, David; Jewell, Oliver J D

2013-01-01

South Africa is reputed to host the world's largest remaining population of white sharks, yet no studies have accurately determined a population estimate based on mark-recapture of live individuals. We used dorsal fin photographs (fin IDs) to identify white sharks in Gansbaai, South Africa, from January 2007-December 2011. We used the computer programme DARWIN to catalogue and match fin IDs of individuals; this is the first study to successfully use the software for white shark identification. The programme performed well despite a number of individual fins showing drastic changes in dorsal fin shape over time. Of 1682 fin IDs used, 532 unique individuals were identified. We estimated population size using the open-population POPAN parameterisation in Program MARK, which estimated the superpopulation size at 908 (95% confidence interval 808-1008). This estimated population size is considerably larger than those described at other aggregation areas of the species and is comparable to a previous South African population estimate conducted 16 years prior. Our assessment suggests the species has not made a marked recovery since being nationally protected in 1991. As such, additional international protection may prove vital for the long-term conservation of this threatened species.

Cryptomyrus: a new genus of Mormyridae (Teleostei, Osteoglossomorpha) with two new species from Gabon, West-Central Africa

PubMed Central

Sullivan, John P.; Lavoué, Sébastien; Hopkins, Carl D.

2016-01-01

Abstract We use mitochondrial and nuclear sequence data to show that three weakly electric mormyrid fish specimens collected at three widely separated localities in Gabon, Africa over a 13-year period represent an unrecognized lineage within the subfamily Mormyrinae and determine its phylogenetic position with respect to other taxa. We describe these three specimens as a new genus containing two new species. Cryptomyrus, new genus, is readily distinguished from all other mormyrid genera by a combination of features of squamation, morphometrics, and dental attributes. Cryptomyrus ogoouensis, new species, is differentiated from its single congener, Cryptomyrus ona, new species, by the possession of an anal-fin origin located well in advance of the dorsal fin, a narrow caudal peduncle and caudal-fin lobes nearly as long as the peduncle. In Cryptomyrus ona, the anal-fin origin is located only slightly in advance of the dorsal fin, the caudal peduncle is deep and the caudal-fin lobes considerably shorter than the peduncle. Continued discovery of new taxa within the “Lower Guinea Clade” of Mormyridae highlights the incompleteness of our knowledge of fish diversity in West-Central Africa. We present a revised key to the mormyrid genera of Lower Guinea. PMID:27006619

Sounds from airguns and fin whales recorded in the mid-Atlantic Ocean, 1999-2009.

PubMed

Nieukirk, Sharon L; Mellinger, David K; Moore, Sue E; Klinck, Karolin; Dziak, Robert P; Goslin, Jean

2012-02-01

Between 1999 and 2009, autonomous hydrophones were deployed to monitor seismic activity from 16° N to 50° N along the Mid-Atlantic Ridge. These data were examined for airgun sounds produced during offshore surveys for oil and gas deposits, as well as the 20 Hz pulse sounds from fin whales, which may be masked by airgun noise. An automatic detection algorithm was used to identify airgun sound patterns, and fin whale calling levels were summarized via long-term spectral analysis. Both airgun and fin whale sounds were recorded at all sites. Fin whale calling rates were higher at sites north of 32° N, increased during the late summer and fall months at all sites, and peaked during the winter months, a time when airgun noise was often prevalent. Seismic survey vessels were acoustically located off the coasts of three major areas: Newfoundland, northeast Brazil, and Senegal and Mauritania in West Africa. In some cases, airgun sounds were recorded almost 4000 km from the survey vessel in areas that are likely occupied by fin whales, and at some locations airgun sounds were recorded more than 80% days/month for more than 12 consecutive months. © 2012 Acoustical Society of America

Live fate-mapping of joint-associated fibroblasts visualizes expansion of cell contributions during zebrafish fin regeneration.

PubMed

Tornini, Valerie A; Thompson, John D; Allen, Raymond L; Poss, Kenneth D

2017-08-15

The blastema is a mass of progenitor cells responsible for regeneration of amputated salamander limbs and fish fins. Previous studies have indicated that resident cell sources producing the blastema contribute lineage-restricted progeny to regenerating tissue. However, these studies have labeled general cell types rather than granular cell subpopulations, and they do not explain the developmental transitions that must occur for distal structures to arise from cells with proximal identities in the appendage stump. Here, we find that regulatory sequences of tph1b , which encodes an enzyme that synthesizes serotonin, mark a subpopulation of fibroblast-like cells restricted to the joints of uninjured adult zebrafish fins. Amputation stimulates serotonin production in regenerating fin fibroblasts, yet targeted tph1b mutations abrogating this response do not disrupt fin regeneration. In uninjured animals, tph1b -expressing cells contribute fibroblast progeny that remain restricted to joints throughout life. By contrast, upon amputation, tph1b + joint cells give rise to fibroblasts that distribute across the entire lengths of regenerating fin rays. Our experiments visualize and quantify how incorporation into an appendage blastema broadens the progeny contributions of a cellular subpopulation that normally has proximodistal restrictions. © 2017. Published by The Company of Biologists Ltd.

Comparison of work function variation between FinFET and 3D stacked nanowire FET devices for 6-T SRAM reliability

NASA Astrophysics Data System (ADS)

Ko, Kyul; Son, Dokyun; Kang, Myounggon; Shin, Hyungcheol

2018-02-01

In this work, work-function variation (WFV) on 5 nm node gate-all-around (GAA) silicon 3D stacked nanowire FET (NWFET) and FinFET devices are studied for 6-T SRAM cells through 3D technology computer-aided design (TCAD) simulation. The NWFET devices have strong immunity for the unprecedented short channel effects (SCEs) compared with the FinFET devices owing to increased gate controllability. However, due to the narrow gate area, the single NWFET is more vulnerable to WFV effects than FinFET devices. Our results show that the WFV effects on single NWFETs are larger than the FinFETs by 45-55%. In the case of standard SRAM bit cells (high density: 111 bit cell), the variation of read stability (read static noise margin) on single NWFETs are larger than the FinFETs by 65-75%. Therefore, to improve the performance and having immunity to WFV effects, it is important to analyze the degree of variability in 3D stacked device architectures without area penalty. Moreover, we investigated the WFV effects for an accurate guideline with regard to grain size (GS) and channel area of 3D stacked NWFET in 6-T SRAM bit cells.

Morphological observation and length-weight relationship of critically endangered riverine catfish Rita rita (Hamilton).

PubMed

Amin, M R; Mollah, M F A; Taslima, K; Muhammadullah

2014-01-15

The experiment was conducted to investigate the morphological status of the critically endangered riverine catfish Rita rita using morphometric and meristic traits. About 158 species of Rita were collected from the old Brahmaputra river in Mymensingh district and were studied in the laboratory of the Fisheries Biology and Genetics Department, Bangladesh Agricultural University. Measurement of length and weight of Rita were recorded by using measuring scale and electric balance respectively. Significant curvilinear relationship existed between total length and other morphometric characters and between head length and other characters of the head. Relationships between total length and various body measurements of the fish were highly significant (p < 0.01) except the relationship between total length and pelvic fin length of male fish (p < 0.05). In case of meristic characters-dorsal fin rays, pelvic fin rays, pectoral fin rays, anal fin rays, caudal fin rays, number of vertebrae and branchiostegal rays were found to be more or less similar except slight differences. The values of condition factors (k) in the total length body-weight relationships for female and male were found to be 0.41 and 0.38, respectively. The mean values of relative condition factors (kn) were 1.0 and 1.005 for female and male, respectively.

Alburnoides manyasensis (Actinopterygii, Cyprinidae), a new species of cyprinid fish from Manyas Lake basin, Turkey

PubMed Central

Turan, Davut; Ekmekçi, F. Güler; Kaya, Cüneyt; Güçlü, S. Serkan

2013-01-01

Abstract Alburnoides manyasensis, sp. n., is described from the Koca Stream (Lake Manyas drainage, Marmara Sea basin) in Anatolia. It is distinguished from all species of Alburnoides in Turkey and adjacent regions, Alburnoides tzanevi (Rezovska [Rezve], Istranca and Terkos streams in the western Black Sea drainage), Alburnoides cf. smyrnae (Banaz Stream, a drainage of Büyük Menderes River, Aegean Sea basin), Alburnoides fasciatus (streams and rivers in the eastern Black Sea drainage) and Alburnoides eichwaldii (Kura and Aras rivers [a drainage of Kura River], Caspian Sea basin) by a combination of the following characters (none unique to the species):marked hump at nape, especially in specimens larger than 60 mm SL; partly developed ventral keel between pelvic fin and anal fin, scaleless 1/2 to 2/3 its length; body depth at dorsal-fin origin 29−32% SL; caudal peduncle depth 11−12% SL; 45–52+ 2–3 lateral-line scales; 9–12 scale rows between lateral line and dorsal-fin origin; 4–5 scale rows between lateral line and anal-fin origin, 10½–12½ branched anal-fin rays; 40–42 total vertebrae. PMID:23794819

Gauging the Threat: The First Population Estimate for White Sharks in South Africa Using Photo Identification and Automated Software

PubMed Central

Towner, Alison V.; Wcisel, Michelle A.; Reisinger, Ryan R.; Edwards, David; Jewell, Oliver J. D.

2013-01-01

South Africa is reputed to host the world’s largest remaining population of white sharks, yet no studies have accurately determined a population estimate based on mark-recapture of live individuals. We used dorsal fin photographs (fin IDs) to identify white sharks in Gansbaai, South Africa, from January 2007 – December 2011. We used the computer programme DARWIN to catalogue and match fin IDs of individuals; this is the first study to successfully use the software for white shark identification. The programme performed well despite a number of individual fins showing drastic changes in dorsal fin shape over time. Of 1682 fin IDs used, 532 unique individuals were identified. We estimated population size using the open-population POPAN parameterisation in Program MARK, which estimated the superpopulation size at 908 (95% confidence interval 808–1008). This estimated population size is considerably larger than those described at other aggregation areas of the species and is comparable to a previous South African population estimate conducted 16 years prior. Our assessment suggests the species has not made a marked recovery since being nationally protected in 1991. As such, additional international protection may prove vital for the long-term conservation of this threatened species. PMID:23776600

How predation shaped fish: the impact of fin spines on body form evolution across teleosts.

PubMed

Price, S A; Friedman, S T; Wainwright, P C

2015-11-22

It is well known that predators can induce morphological changes in some fish: individuals exposed to predation cues increase body depth and the length of spines. We hypothesize that these structures may evolve synergistically, as together, these traits will further enlarge the body dimensions of the fish that gape-limited predators must overcome. We therefore expect that the orientation of the spines will predict which body dimension increases in the presence of predators. Using phylogenetic comparative methods, we tested this prediction on the macroevolutionary scale across 347 teleost families, which display considerable variation in fin spines, body depth and width. Consistent with our predictions, we demonstrate that fin spines on the vertical plane (dorsal and anal fins) are associated with a deeper-bodied optimum. Lineages with spines on the horizontal plane (pectoral fins) are associated with a wider-bodied optimum. Optimal body dimensions across lineages without spines paralleling the body dimension match the allometric expectation. Additionally, lineages with longer spines have deeper and wider body dimensions. This evolutionary relationship between fin spines and body dimensions across teleosts reveals functional synergy between these two traits and a potential macroevolutionary signature of predation on the evolutionary dynamics of body shape. © 2015 The Author(s).

Evaluation of Heating Methods for Thermal Structural Testing of Large Structures

NASA Technical Reports Server (NTRS)

Daryabeigi, Kamran; Sikora, Joseph G.; Caldwell, Darrell L., Jr.

1998-01-01

An experimental study was conducted to evaluate different heating methods for thermal structural testing of large scale structures at temperatures up to 350 F as part of the High Speed Research program. The heating techniques evaluated included: radiative/convective, forced convective, and conductive. The radiative/convective heaters included finned strip heaters, and clear and frosted quartz lamps. The forced convective heating was accomplished by closed loop circulation of heated air. The conductive heater consisted of heating blankets. The tests were conducted on an 1/8 inch thick stainless steel plate in a custom-built oven. The criteria used for comparing the different heating methods included test specimen temperature uniformity, heater response time, and consumed power. The parameters investigated included air circulation in the oven, reflectance of oven walls, and the orientation of the test specimen and heaters (vertical and horizontal). It was found that reflectance of oven walls was not an important parameter. Air circulation was necessary to obtain uniform temperatures only for the vertically oriented specimen. Heating blankets provided unacceptably high temperature non-uniformities. Quartz lamps with internal air circulation had the lowest power consumption levels. Using frosted quartz lamps with closed loop circulation of cool air, and closed loop circulation of heated air provided the fastest response time.

Space shuttle: Directional and lateral stability and interference effects of cruise engine location on a 0.015 scale space shuttle

NASA Technical Reports Server (NTRS)

Buchholz, R. E.

1972-01-01

The results are presented that were obtained from a wind tunnel tests to improve space shuttle booster baseline lateral-directional stability, control characteristics, and cruise engine location optimization. Tests were conducted in a 7 x 10-foot transonic wind tunnel. The model employed was a 0.015-scale replica of a space shuttle booster. The three major objectives of this test were to determine the following: (1) force, static stability, and control effectiveness characteristics for varying angles of positive and negative wing dihedral and various combinations of wing tip and centerline dorsal fins; (2) force and static stability characteristics of cruise engines location on the body below the high aerodynamic canard; and (3) control effectiveness for the low-mounted wing configuration. The wing dihedral study was conducted at a cruise Mach number of 0.40 and simulated altitude of 10,000 feet. Portions of the test were conducted to determine the control surfaces stability and control characteristics over the Mach number range of 0.4 to 1.2. The aerodynamic characteristics determined are based on a unit Reynolds number of approximately 2 million per foot. Boundary layer trip strips were employed to induce boundary layer transition.

Indirect adaptive output feedback control of a biorobotic AUV using pectoral-like mechanical fins.

PubMed

Naik, Mugdha S; Singh, Sahjendra N; Mittal, Rajat

2009-06-01

This paper treats the question of servoregulation of autonomous underwater vehicles (AUVs) in the yaw plane using pectoral-like mechanical fins. The fins attached to the vehicle have oscillatory swaying and yawing motion. The bias angle of the angular motion of the fin is used for the purpose of control. Of course, the design approach considered here is applicable to AUVs for other choices of oscillation patterns of the fins, which produce periodic forces and moments. It is assumed that the vehicle parameters, hydrodynamic coefficients, as well the fin forces and moments are unknown. For the trajectory control of the yaw angle, a sampled-data indirect adaptive control system using output (yaw angle) feedback is derived. The control system has a modular structure, which includes a parameter identifier and a stabilizer. For the control law derivation, an internal model of the exosignals (reference signal (constant or ramp) and constant disturbance) is included. Unlike the direct adaptive control scheme, the derived control law is applicable to minimum as well as nonminimum phase biorobotic AUVs (BAUVs). This is important, because for most of the fin locations on the vehicle, the model is a nonminimum phase. In the closed-loop system, the yaw angle trajectory tracking error converges to zero and the remaining state variables remain bounded. Simulation results are presented which show that the derived modular control system accomplishes precise set point yaw angle control and turning maneuvers in spite of the uncertainties in the system parameters using only yaw angle feedback.

Machine-Thermal Coupling Stresses Analysis of the Fin-Type Structural Thermoelectric Generator

NASA Astrophysics Data System (ADS)

Zhang, Zheng; Yue, Hao; Chen, Dongbo; Qin, Delei; Chen, Zijian

2017-05-01

The design structure and heat-transfer mechanism of a thermoelectric generator (TEG) determine its body temperature state. Thermal stress and thermal deformation generated by the temperature variation directly affect the stress state of thermoelectric modules (TEMs). Therefore, the rated temperature and pressing force of TEMs are important parameters in TEG design. Here, the relationships between structural of a fin-type TEG (FTEG) and these parameters are studied by modeling and "machine-thermal" coupling simulation. An indirect calculation method is adopted in the coupling simulation. First, numerical heat transfer calculations of a three-dimensional FTEG model are conducted according to an orthogonal simulation table. The influences of structural parameters for heat transfer in the channel and outer fin temperature distribution are analyzed. The optimal structural parameters are obtained and used to simulate temperature field of the outer fins. Second, taking the thermal calculation results as the initial condition, the thermal-solid coupling calculation is adopted. The thermal stresses of outer fin, mechanical force of spring-angle pressing mechanism, and clamping force on a TEM are analyzed. The simulation results show that the heat transfer area of the inner fin and the physical parameters of the metal materials are the keys to determining the FTEG temperature field. The pressing mechanism's mechanical force can be reduced by reducing the outer fin angle. In addition, a corrugated cooling water pipe, which has cooling and spring functionality, is conducive to establishing an adaptable clamping force to avoid the TEMs being crushed by the thermal stresses in the body.

Molecular cloning and characterization of V2-type receptor in two ray-finned fish, gray bichir, Polypterus senegalus and medaka, Oryzias latipes.

PubMed

Konno, Norifumi; Kurosawa, Mayumi; Kaiya, Hiroyuki; Miyazato, Mikiya; Matsuda, Kouhei; Uchiyama, Minoru

2010-07-01

In tetrapods, vasopressin (VP) and vasotocin (VT) are involved in various aspects of physiology and behavior including osmoregulation, cardiovascular function, reproduction, stress response and social behavior. Pharmacological and molecular studies have identified three types of VP/VT receptors, V1a-type (V1aR), V1b-type (V1bR) and V2-type (V2R). On the other hand, only V1aR has so far been identified in teleosts. In the present study, we successfully cloned V2Rs from two ray-finned fish, gray bichir and medaka. Phylogenetic analysis showed that the cloned receptors belong to the V2R group of lobe-finned fish and tetrapods. The amino acid sequences of bichir V2R and medaka V2R were high identity (60-65.5% and 53.2-80.9%, respectively) with other known V2R members, respectively. Reverse transcriptase PCR revealed that ray-finned fish V2R transcripts have been detected in various tissues including brain, gill, heart, liver, kidney and reproductive organs, suggesting that ray-finned fish V2R might mediate multiple functions of VT. In functional analysis, the cells transfected with the cloned receptors responded with the accumulation of intracellular cAMP in a concentration-dependent manner following VT stimulation, but not respond with [Ca(2+)]i. Furthermore, pretreatment with mammalian V2R antagonist (OPC-31260) to the cells transfected with medaka V2R significantly inhibited an increase of the VT-induced intracellular cAMP. These results suggest that ray-finned fish possess a functional V2R linked to adenylate cyclase and the cAMP signaling pathway as well as V2Rs of lobe-finned fish and tetrapods. Thus, the present study suggests that functional V2R evolved prior to the divergence of the ray- and lobe-finned fish lineages. Copyright 2010 Elsevier Inc. All rights reserved.

North Atlantic Blue and Fin Whales Suspend Their Spring Migration to Forage in Middle Latitudes: Building up Energy Reserves for the Journey?

PubMed Central

Silva, Mónica A.; Prieto, Rui; Jonsen, Ian; Baumgartner, Mark F.; Santos, Ricardo S.

2013-01-01

The need to balance energy reserves during migration is a critical factor for most long-distance migrants and an important determinant of migratory strategies in birds, insects and land mammals. Large baleen whales migrate annually between foraging and breeding sites, crossing vast ocean areas where food is seldom abundant. How whales respond to the demands and constraints of such long migrations remains unknown. We applied a behaviour discriminating hierarchical state-space model to the satellite tracking data of 12 fin whales and 3 blue whales tagged off the Azores, to investigate their movements, behaviour (transiting and area-restricted search, ARS) and daily activity cycles during the spring migration. Fin and blue whales remained at middle latitudes for prolonged periods, spending most of their time there in ARS behaviour. While near the Azores, fin whale ARS behaviour occurred within a restricted area, with a high degree of overlap among whales. There were noticeable behavioural differences along the migratory pathway of fin whales tracked to higher latitudes: ARS occurred only in the Azores and north of 56°N, whereas in between these areas whales travelled at higher overall speeds while maintaining a nearly direct trajectory. This suggests fin whales may alternate periods of active migration with periods of extended use of specific habitats along the migratory route. ARS behaviour in blue whales occurred over a much wider area as whales slowly progressed northwards. The tracks of these whales terminated still at middle latitudes, before any behavioural switch was detected. Fin whales exhibited behavioural-specific diel rhythms in swimming speed but these varied significantly between geographic areas, possibly due to differences in the day-night cycle across areas. Finally, we show a link between fin whales seen in the Azores and those summering in eastern Greenland-western Iceland along a migratory corridor located in central Atlantic waters. PMID:24116112

Annual Acoustic Presence of Fin Whale (Balaenoptera physalus) Offshore Eastern Sicily, Central Mediterranean Sea

PubMed Central

Sciacca, Virginia; Caruso, Francesco; Beranzoli, Laura; Chierici, Francesco; De Domenico, Emilio; Embriaco, Davide; Favali, Paolo; Giovanetti, Gabriele; Larosa, Giuseppina; Marinaro, Giuditta; Papale, Elena; Pavan, Gianni; Pellegrino, Carmelo; Pulvirenti, Sara; Simeone, Francesco; Viola, Salvatore; Riccobene, Giorgio

2015-01-01

In recent years, an increasing number of surveys have definitively confirmed the seasonal presence of fin whales (Balaenoptera physalus) in highly productive regions of the Mediterranean Sea. Despite this, very little is yet known about the routes that the species seasonally follows within the Mediterranean basin and, particularly, in the Ionian area. The present study assesses for the first time fin whale acoustic presence offshore Eastern Sicily (Ionian Sea), throughout the processing of about 10 months of continuous acoustic monitoring. The recording of fin whale vocalizations was made possible by the cabled deep-sea multidisciplinary observatory, “NEMO-SN1”, deployed 25 km off the Catania harbor at a depth of about 2,100 meters. NEMO-SN1 is an operational node of the European Multidisciplinary Seafloor and water-column Observatory (EMSO) Research Infrastructure. The observatory was equipped with a low-frequency hydrophone (bandwidth: 0.05 Hz–1 kHz, sampling rate: 2 kHz) which continuously acquired data from July 2012 to May 2013. About 7,200 hours of acoustic data were analyzed by means of spectrogram display. Calls with the typical structure and patterns associated to the Mediterranean fin whale population were identified and monitored in the area for the first time. Furthermore, a background noise analysis within the fin whale communication frequency band (17.9–22.5 Hz) was conducted to investigate possible detection-masking effects. The study confirms the hypothesis that fin whales are present in the Ionian Sea throughout all seasons, with peaks in call detection rate during spring and summer months. The analysis also demonstrates that calls were more frequently detected in low background noise conditions. Further analysis will be performed to understand whether observed levels of noise limit the acoustic detection of the fin whales vocalizations, or whether the animals vocalize less in the presence of high background noise. PMID:26581104

Resolving Shifting Patterns of Muscle Energy Use in Swimming Fish

PubMed Central

Gerry, Shannon P.; Ellerby, David J.

2014-01-01

Muscle metabolism dominates the energy costs of locomotion. Although in vivo measures of muscle strain, activity and force can indicate mechanical function, similar muscle-level measures of energy use are challenging to obtain. Without this information locomotor systems are essentially a black box in terms of the distribution of metabolic energy. Although in situ measurements of muscle metabolism are not practical in multiple muscles, the rate of blood flow to skeletal muscle tissue can be used as a proxy for aerobic metabolism, allowing the cost of particular muscle functions to be estimated. Axial, undulatory swimming is one of the most common modes of vertebrate locomotion. In fish, segmented myotomal muscles are the primary power source, driving undulations of the body axis that transfer momentum to the water. Multiple fins and the associated fin muscles also contribute to thrust production, and stabilization and control of the swimming trajectory. We have used blood flow tracers in swimming rainbow trout (Oncorhynchus mykiss) to estimate the regional distribution of energy use across the myotomal and fin muscle groups to reveal the functional distribution of metabolic energy use within a swimming animal for the first time. Energy use by the myotomal muscle increased with speed to meet thrust requirements, particularly in posterior myotomes where muscle power outputs are greatest. At low speeds, there was high fin muscle energy use, consistent with active stability control. As speed increased, and fins were adducted, overall fin muscle energy use declined, except in the caudal fin muscles where active fin stiffening is required to maintain power transfer to the wake. The present data were obtained under steady-state conditions which rarely apply in natural, physical environments. This approach also has potential to reveal the mechanical factors that underlie changes in locomotor cost associated with movement through unsteady flow regimes. PMID:25165858

Joint Seismic-Geodetic Algorithm for Finite-Fault Detection and Slip Inversion in the West Coast ShakeAlert System

NASA Astrophysics Data System (ADS)

Smith, D. E.; Felizardo, C.; Minson, S. E.; Boese, M.; Langbein, J. O.; Murray, J. R.

2016-12-01

Finite-fault source algorithms can greatly benefit earthquake early warning (EEW) systems. Estimates of finite-fault parameters provide spatial information, which can significantly improve real-time shaking calculations and help with disaster response. In this project, we have focused on integrating a finite-fault seismic-geodetic algorithm into the West Coast ShakeAlert framework. The seismic part is FinDer 2, a C++ version of the algorithm developed by Böse et al. (2012). It interpolates peak ground accelerations and calculates the best fault length and strike from template matching. The geodetic part is a C++ version of BEFORES, the algorithm developed by Minson et al. (2014) that uses a Bayesian methodology to search for the most probable slip distribution on a fault of unknown orientation. Ultimately, these two will be used together where FinDer generates a Bayesian prior for BEFORES via the methodology of Minson et al. (2015), and the joint solution will generate estimates of finite-fault extent, strike, dip, best slip distribution, and magnitude. We have created C++ versions of both FinDer and BEFORES using open source libraries and have developed a C++ Application Protocol Interface (API) for them both. Their APIs allow FinDer and BEFORES to contribute to the ShakeAlert system via an open source messaging system, ActiveMQ. FinDer has been receiving real-time data, detecting earthquakes, and reporting messages on the development system for several months. We are also testing FinDer extensively with Earthworm tankplayer files. BEFORES has been tested with ActiveMQ messaging in the ShakeAlert framework, and works off a FinDer trigger. We are finishing the FinDer-BEFORES connections in this framework, and testing this system via seismic-geodetic tankplayer files. This will include actual and simulated data.

Differentiation of chondrocytes and scleroblasts during dorsal fin skeletogenesis in flounder larvae.

PubMed

Suzuki, Tohru; Haga, Yutaka; Takeuchi, Toshio; Uji, Susumu; Hashimoto, Hisashi; Kurokawa, Tadahide

2003-01-01

In teleosts, the embryonic fin fold consists of a peridermis, an underlying epidermis and a small number of mesenchymal cells. Beginning from such a simple structure, the fin skeletons, including the proximal and distal radials and lepidotrichia (finrays), develop in the dorsal fin fold at the larval stage. Their process of skeletogenesis and embryonic origin are unclear. Using flounder larvae, we report the differentiation process for chondrocytes and scleroblasts prior to fin skeletogenesis and the effects of retinoic acid (RA) on it. In early larvae, the mesenchymal cells grow between the epidermis and spinal cord to form a line of periodical condensations, which are proximal radial primordia, to produce chondrocytes. The prescleroblasts, which ossify the proximal radial cartilages, differentiate in the mesenchymal cells remaining between the cartilages. Then, mesenchymal condensations occur between the distal ends of the proximal radials, forming distal radial primordia, to produce chondrocytes. Simultaneously, condensations occur between the distal radial primordia and peridermis, which are lepidotrichia primordia, to produce prescleroblasts. Exogenous RA specifically inhibits the mesenchymal condensation prior to the proximal radial formation together with the down-regulation of sonic hedgehog (shh) and patched (pta) expression, resulting in the loss of proximal radials. Thus, it was indicated that differentiation of the precursor cells of radials and lepidotrichia begins in the proximal part of the fin fold and that the initial mesenchymal condensation prior to the proximal radial formation is highly susceptible to the effects of RA. Lepidotrichia formation does not occur where proximal radials are absent, indicating that lepidotrichia differentiation requires interaction with the radial cartilages. To examine the suggestion that neural crest cells contribute to the medial fin skeletons, we localized the HNK-1 positive cells in flounder embryos and slug and msxb-positive cells in pufferfish, Fugu rubripes, embryos. That the positive cells commonly arrive at the proximal part of the fin fold does not contradict the suggestion, but their final destiny as radial chondrocytes or lepidotrichia scleroblasts, should be further investigated.

Carbon Nanotube Tape Vibrating Gyroscope

NASA Technical Reports Server (NTRS)

Tucker, Dennis Stephen (Inventor)

2016-01-01

A vibrating gyroscope includes a piezoelectric strip having length and width dimensions. The piezoelectric strip includes a piezoelectric material and carbon nanotubes (CNTs) substantially aligned and polled along the strip's length dimension. A spindle having an axis of rotation is coupled to the piezoelectric strip. The axis of rotation is parallel to the strip's width dimension. A first capacitance sensor is mechanically coupled to the spindle for rotation therewith. The first capacitance sensor is positioned at one of the strip's opposing ends and is spaced apart from one of the strip's opposing faces. A second capacitance sensor is mechanically coupled to the spindle for rotation therewith. The second capacitance sensor is positioned at another of the strip's opposing ends and is spaced apart from another of the strip's opposing faces. A voltage source applies an AC voltage to the piezoelectric strip.

Fiber Reinforced Composite Cores and Panels

NASA Technical Reports Server (NTRS)

Day, Stephen W. (Inventor); Campbell, G. Scott (Inventor); Tilton, Danny E. (Inventor); Stoll, Frederick (Inventor); Sheppard, Michael (Inventor); Banerjee, Robin (Inventor)

2013-01-01

A fiber reinforced core panel is formed from strips of plastics foam helically wound with layers of rovings to form webs which may extend in a wave pattern or may intersect transverse webs. Hollow tubes may replace foam strips. Axial rovings cooperate with overlying helically wound rovings to form a beam or a column. Wound roving patterns may vary along strips for structural efficiency. Wound strips may alternate with spaced strips, and spacers between the strips enhance web buckling strength. Continuously wound rovings between spaced strips permit folding to form panels with reinforced edges. Continuously wound strips are helically wrapped to form annular structures, and composite panels may combine both thermoset and thermoplastic resins. Continuously wound strips or strip sections may be continuously fed either longitudinally or laterally into molding apparatus which may receive skin materials to form reinforced composite panels.

Filmwise Condensation on Low Integral-Fin Tubes of Different Diameter

DTIC Science & Technology

1988-12-01

the prime mover of condensate . Therefore, the Nusselt analysis was not valid for finned tubes. They therefore divided the finned tube into two regions...the objectives of this thesis. Prior to these modifications, cooling water to the secondary condenser was con- tained in two helically wound coils made...temperature difference across condensate film (K), il = dynamic viscosity of condensate (N. s/m 2). By substituting the Nusselt - and the Sieder-Tate

3S(expn 2): Behavioral Response Studies of Cetaceans to Navy Sonar Signals in Norwegian Waters

DTIC Science & Technology

2013-09-30

orca), long-finned pilot (Globicephala melas ), and sperm whales (Physeter macrocephalus) to naval sonar. Aquatic Mammals 38: 362-401. 9...of sonar signals by long-finned pilot whales (Globicephala melas ). Marine Mammal sci Aoki K, Sakai M, Miller PJO, Visser F, Sato K (2013) Body...Orcinus orca), long-finned pilot (Globicephala melas ), and sperm whales (Physeter macrocephalus) to naval sonar. Aquatic Mammals 38: 362-401

3S2: Behavioral Response Studies of Cetaceans to Navy Sonar Signals in Norwegian Waters

DTIC Science & Technology

2015-09-30

long-finned pilot (Globicephala melas ), and sperm whales (Physeter macrocephalus) to naval sonar. Aquatic Mammals 38: 362-401. Moretti, D., Thomas, L...2014). The social context of individual foraging behaviour in long-finned pilot whales (Globicephala melas ). Behaviour 151: 1453-1477. DOI: 10.1163...response thresholds for avoidance of sonar by free-ranging long-finned pilot whales (Globicephala melas ). Mar. Poll. Bull.83: 165-180. DOI: 10.1016

3S2: Behavioral Response Studies of Cetaceans to Navy Sonar Signals in Norwegian Waters

DTIC Science & Technology

2015-09-30

experimental exposures of killer (Orcinus orca), long-finned pilot (Globicephala melas ), and sperm whales (Physeter macrocephalus) to naval sonar. Aquatic...Kvadsheim P.H., Huisman J. and Tyack P.L. (2014). The social context of individual foraging behaviour in long-finned pilot whales (Globicephala melas ...Wensveen P.J., Miller P. J. O. (2014). High response thresholds for avoidance of sonar by free-ranging long-finned pilot whales (Globicephala melas

Environmental Influences on Diel Calling Behavior in Baleen Whales

DTIC Science & Technology

2013-09-30

to allow known calls (e.g., right whale upcall and gunshot, fin whale 20- Hz pulses, humpback whale downsweeps, sei whale low-frequency downsweeps...fin, humpback , sei, and North Atlantic right whales . Real-time detections were evaluated after recovery of the gliders by (1) comparing the acoustic...from both an aircraft and ship. The overall false detection rate for individual calls was 14%, and for right, humpback , and fin whales , false

Development of a Four-Fin Bio-Inspired UUV: CFD Studies

DTIC Science & Technology

2012-09-04

6.5ʺ″, V= 1kt, δ = -43.6°. .................................. 17   Fig. 32. Particles traces just near stroke reversal of the front and rear fins...have been studied to understand how certain aquatic animals achieve their high levels of controllability. Blake [1] determined that in low- speed...fin, the amplitude of the flapping and starting location of the down stroke . These simulations were performed in order to evaluate the hydrodynamic

Effects of Base Cavity Depth on a Free Spinning Wrap-Around Fin Missile Configuration

DTIC Science & Technology

1995-12-01

packaging problem. Current missile systems which possess wrap-around fin designs are the Army’s Multiple Launch Rocket System (MLRS) and the Hard Target...aerodynamic irregularities (2). Of particular importance to projectile designers is the side force/moment inherent to wrap-around fin configurations. During...virtual instrument programs integrated to perform all necessary aspects of calibration, data collection, and reduction. The details surrounding the design

Conical similarity of shock/boundary layer interactions generated by swept fins

NASA Technical Reports Server (NTRS)

Lu, F. K.; Settles, G. S.

1983-01-01

A parametric experimental study has been made of the class of 3D shock wave/turbulent boundary layer interactions generated by swept-leading-edge fins. The fin sweepback angles ranged from 0 to 65 deg at angles of attack of 5, 9, and 15 deg. Two equilibrium 2D turbulent boundary layers with a free-stream Mach number of 2.95 and a Reynolds number of 6.3 x 10 to the 7th/m were used as incoming flow conditions. All the resulting interactions were found to possess conical symmetry of surface pressures and skin friction lines beyond an initial inception zone. Further, these interactions revealed a simple similarity based on inviscid shock strength irrespective of fin sweepback or angle of attack.

Hybrid Heat Exchangers

NASA Technical Reports Server (NTRS)

Tu, Jianping Gene; Shih, Wei

2010-01-01

A hybrid light-weight heat exchanger concept has been developed that uses high-conductivity carbon-carbon (C-C) composites as the heat-transfer fins and uses conventional high-temperature metals, such as Inconel, nickel, and titanium as the parting sheets to meet leakage and structural requirements. In order to maximize thermal conductivity, the majority of carbon fiber is aligned in the fin direction resulting in 300 W/m.K or higher conductivity in the fin directions. As a result of this fiber orientation, the coefficient of thermal expansion (CTE) of the C-C composite in both non-fiber directions matches well with the CTE of various high-temperature metal alloys. This allows the joining of fins and parting sheets by using high-temperature braze alloys.

The equivalent angle-of-attack method for estimating the nonlinear aerodynamic characteristics of missile wings and control surfaces

NASA Technical Reports Server (NTRS)

Hemsch, M. J.; Nielsen, J. N.

1982-01-01

A method has been developed for estimating the nonlinear aerodynamic characteristics of missile wing and control surfaces. The method is based on the following assumption: if a fin on a body has the same normal-force coefficient as a wing alone composed of two of the same fins joined together at their root chords, then the other force and moment coefficients of the fin and the wing alone are the same including the nonlinearities. The method can be used for deflected fins at arbitrary bank angles and at high angles of attack. In the paper, a full derivation of the method is given, its accuracy demonstrated and its use in extending missile data bases is shown.

Thrust production and wake structure of a batoid-inspired oscillating fin

PubMed Central

CLARK, R. P.; SMITS, A. J.

2009-01-01

Experiments are reported on the hydrodynamic performance of a flexible fin. The fin replicates some features of the pectoral fin of a batoid fish (such as a ray or skate) in that it is actuated in a travelling wave motion, with the amplitude of the motion increasing linearly along the span from root to tip. Thrust is found to increase with non-dimensional frequency, and an optimal oscillatory gait is identified. Power consumption measurements lead to the computation of propulsive efficiency, and an optimal efficiency condition is evaluated. Wake visualizations are presented, and a vortex model of the wake near zero net thrust is suggested. Strouhal number effects on the wake topology are also illustrated. PMID:19746188

Evolution of motor innervation to vertebrate fins and limbs.

PubMed

Murakami, Yasunori; Tanaka, Mikiko

2011-07-01

The evolution and diversification of vertebrate behaviors associated with locomotion depend highly on the functional transformation of paired appendages. Although the evolution of fins into limbs has long been a focus of interest to scientists, the evolution of neural control during this transition has not received much attention. Recent studies have provided significant progress in the understanding of the genetic and developmental bases of the evolution of fin/limb motor circuitry in vertebrates. Here we compare the organization of the motor neurons in the spinal cord of various vertebrates. We also discuss recent advances in our understanding of these events and how they can provide a mechanistic explanation for the evolution of fin/limb motor circuitry in vertebrates. Copyright © 2011 Elsevier Inc. All rights reserved.

Comparison between different interdental stripping methods and evaluation of abrasive strips: SEM analysis.

PubMed

Grippaudo, Cristina; Cancellieri, Daniela; Grecolini, Maria E; Deli, Roberto

2010-01-01

The aim of this study was to evaluate the morphological effects and the surface irregularities produced by different methods of mechanical stripping (abrasive strips and burs) and chemical stripping (37% orthophosphoric acid) and the surface changes following the finishing procedures (polishing strips) or the subsequent application of sealants, in order to establish the right stripping method that can guarantee the smoothest surface. We have also analysed the level of wear on the different abrasive strips employed, according to their structure. 160 proximal surfaces of 80 sound molar teeth extracted for orthodontic and periodontal reasons, were divided into: 1 control group with non-treated enamel proximal surfaces and 5 different groups according to the stripping method used, were observed with scanning electron microscopy (SEM). Each one of the 5 treated groups was also divided into 3 different subgroups according to the finishing procedures or the subsequent application of sealants. The finishing stage following the manual reduction proves to be fundamental in reducing the number and depth of grooves created by the stripping. After the air rotor stripping method, the use of sealants is advised in order to obtain a smoother surface. The analysis of the combinations of mechanical and chemical stripping showed unsatisfactory results. Concerning the wear of the strips, we have highlighted a different abrasion degree for the different types of strips analysed with SEM. The enamel damages are limited only if the finishing procedure is applied, independently of the type of abrasive strip employed. It would be advisable, though clinically seldom possible, the use of sealants after the air rotor stripping technique. Copyright © 2010 Società Italiana di Ortodonzia SIDO. Published by Elsevier Srl. All rights reserved.

Three new species of Trimma (Pisces; Gobioidei) from Indonesia.

PubMed

Winterbottom, Richard; Erdmann, Mark V; Cahyani, N K Dita

2014-07-18

Three new species of Trimma are described from various localities in Indonesia. All three can be readily identified from their live, freshly collected, or preserved colouration. Trimma meranyx n. sp. is further distinguished from other species by the possession of 8-9 scales in the predorsal midline, up to three rows of (usually) cycloid scales on the opercle, two scales at the posterodorsal border of the cheek, a very slightly elongate second dorsal spine which only just reaches the spine or anterior rays of the second dorsal fin, unbranched pectoral fin rays, a fifth pelvic fin ray that branches once and is 64-85% the length of the fourth ray, and a full basal membrane connecting the inner branches of the two fifth pelvic rays. The dark red (live) or black posterior half of the caudal peduncle with large white spots straddling the dorsal and ventral midlines just anterior to the first procurrent caudal fin rays is the diagnostic colour character. The species is known from North Sulawesi, West Papua (Raja Ampat and Fakfak), and the south-eastern tip of Papua New Guinea, with possible records from the Philippines and Vanuatu. Trimma pajama n. sp. has 6 scales in the predorsal midline, two ctenoid scales along the dorsal margin of the opercle, a slightly elongate second dorsal spine reaching posteriorly to the base of the spine or first ray of the second dorsal fin, unbranched pectoral fin rays, a fifth pelvic ray with a single branch point and which is 58-72% the length of the fourth ray, and a full basal membrane connecting the inner branches of the two fifth pelvic rays. The live, freshly collected and preserved colour pattern of alternating dark and light stripes on the head and most of the body (except the posterior half of the caudal peduncle) is diagnostic. It is currently known from West Papua (Raja Ampat and Fakfak) and the southern tip of Papua New Guinea, with possible records from Kalimantan (Indonesia), Palau, the Hermit Is (Papua New Guinea) and the Solomon Islands. Trimma zurae n. sp. has 8-9 scales in the predorsal midline, usually a single row of cycloid scales along the upper border of the opercle, 11 anterior and 9 posterior transverse scale rows, no elongated spines in the first dorsal fin, 9 dorsal and 8 anal fin rays, the middle rays of the pectoral fin branched, a single branch in the fifth pelvic fin ray which is 65-76% the length of the fourth ray and a reduced basal membrane of < 20% the length of the fifth ray. The eye-diameter sized black ocellated spot between the first to fifth spines of the first dorsal fin is diagnostic, as are the pupil-diameter sized orange spots on the nape, opercle and posterodorsal part of the cheek. It is currently known only from a single locality just west of Manado, Sulawesi. 

Guidelines for the application of removeable rumble strips

DOT National Transportation Integrated Search

2006-08-01

This work was initiated to assess the viability of removable rumble strips as replacements for asphalt rumble strips, particularly in short term highway work zones. The two rumble strips tested were the Orange Rumble Strip from Advanced Traffic Marki...

Microplasma generator and methods therefor

DOEpatents

Hopwood, Jeffrey A

2015-04-14

A low-temperature, atmospheric-pressure microplasma generator comprises at least one strip of metal on a dielectric substrate. A first end of the strip is connected to a ground plane and the second end of the strip is adjacent to a grounded electrode, with a gap being defined between the second end of the strip and the grounded electrode. High frequency power is supplied to the strip. The frequency is selected so that the length of the strip is an odd integer multiple of 1/4 of the wavelength traveling on the strip. A microplasma forms in the gap between the second end of the strip and the grounded electrode due to electric fields in that region. A microplasma generator array comprises a plurality of strongly-coupled resonant strips in close proximity to one another. At least one of the strips has an input for high-frequency electrical power. The remaining strips resonate due to coupling from the at least one powered strip. The array can provide a continuous line or ring of plasma. The microplasma generator can be used to alter the surface of a substrate, such as by adding material (deposition), removal of material (etching), or modifying surface chemistry.

Characteristics of laminates with delamination control strips

NASA Technical Reports Server (NTRS)

Sun, C. T.; Goering, J. C.; Alper, J. M.; Gause, L. W.

1992-01-01

Tough resin is needed to resist delamination crack propagation. However, modulus often has to be compromised because it is difficult to retain both high modulus and toughness in a matrix material. A potential solution is to use a hybrid system in which tough resin strips are included within a conventional matrix composite. By adjusting the spacing of the tough resin strips, maximum delamination size can be controlled. Experimental results for impact damage and subsequent damage propagation in laminates containing tough resin strips are reported. Plain adhesive strips and fiber-reinforced tough resin composite strips were used in constructing the hybrid laminates. Test results indicated that size of delamination inflicted by impact was confined between the tough resin strips. As a result, significantly increased residual compressive strength was obtained. Impacted laminates containing tough resin strips were also fatigue tested. It was found that these strips reduced the growth of the impact damage area relative to the growth seen in coupons with no tough resin strips. Damage growth from an open hole under tension fatigue was evaluated using both tough resin strips and glass fiber reinforced tough resin strips. Unreinforced tough resin strips retarded delamination growth from the open hole, but did not stop matrix cracks growing in the fiber direction. Fiber reinforced tough resin strips did not contain axial delamination growth from the open hole. However, they did act as crack arresters, stopping the through-the-thickness tension crack originating from the hole.

Flow and heat transfer enhancement in tube heat exchangers

NASA Astrophysics Data System (ADS)

Sayed Ahmed, Sayed Ahmed E.; Mesalhy, Osama M.; Abdelatief, Mohamed A.

2015-11-01

The performance of heat exchangers can be improved to perform a certain heat-transfer duty by heat transfer enhancement techniques. Enhancement techniques can be divided into two categories: passive and active. Active methods require external power, such as electric or acoustic field, mechanical devices, or surface vibration, whereas passive methods do not require external power but make use of a special surface geometry or fluid additive which cause heat transfer enhancement. The majority of commercially interesting enhancement techniques are passive ones. This paper presents a review of published works on the characteristics of heat transfer and flow in finned tube heat exchangers of the existing patterns. The review considers plain, louvered, slit, wavy, annular, longitudinal, and serrated fins. This review can be indicated by the status of the research in this area which is important. The comparison of finned tubes heat exchangers shows that those with slit, plain, and wavy finned tubes have the highest values of area goodness factor while the heat exchanger with annular fin shows the lowest. A better heat transfer coefficient ha is found for a heat exchanger with louvered finned and thus should be regarded as the most efficient one, at fixed pumping power per heat transfer area. This study points out that although numerous studies have been conducted on the characteristics of flow and heat transfer in round, elliptical, and flat tubes, studies on some types of streamlined-tubes shapes are limited, especially on wing-shaped tubes (Sayed Ahmed et al. in Heat Mass Transf 50: 1091-1102, 2014; in Heat Mass Transf 51: 1001-1016, 2015). It is recommended that further detailed studies via numerical simulations and/or experimental investigations should be carried out, in the future, to put further insight to these fin designs.

Pethia aurea (Teleostei: Cyprinidae), a new species of barb from West Bengal, India, with redescription of P. gelius and P. canius.

PubMed

Knight, J D Marcus

2013-01-01

Fishes currently assigned to Pethia gelius Hamilton from West Bengal are shown to belong to a closely-related group of three species: P gelius, its erstwhile synonym P canius Hamilton and a new species, P aurea. The three species are distinguished from all other species of Pethia by having the lateral line incomplete, with 3-4 pored scales; 20-26 scales in lateral series on body; ½4-5/l/2-3½ scales in transverse line on body; 8-9 predorsal scales; barbels absent and by a unique colour pattern consisting of two or three black blotches on the body (which, however, fade on preservation), the first behind the opercle, the second beneath the origin of the dorsal fin, extending to the mid-lateral region, and the third above the origin of the anal fin. A black spot is also present at the base of the dorsal and anal fins. Additionally, P gelius is distinguished by having the last unbranched dorsal-fin ray thick, straight, serrated, with 20-25 serrae on its posterior margin; a snout length of 6.1-8.4% standard length (SL); a body depth of 32.6-37.7% SL; and a dorsal-fin height of 19.4-22.8% SL. Pethia canius is additionally distinguished by having a snout length of 8.9-11.8% SL; a body depth of 28.1-32.2% SL; and dorsal-fin height of 26.9-32.8% SL. Pethia aurea, new species, is additionally distinguished from all its congeners by having ½5/1/3-3½ scales in transverse line on body; 9 pre-dorsal scales; and last unbranched dorsal-fin ray slender, serrated, with 19-22 serrae on posterior margin.

The use of the finasteride-adjusted Prostate Cancer Prevention Trial Prostate Cancer Risk Calculator in a Mexican referral population: a validation study.

PubMed

Liang, Yuanyuan; Ketchum, Norma S; Louden, Christopher; Jimenez-Rios, Miguel A; Thompson, Ian M; Camarena-Reynoso, Hector R

2012-01-01

To perform the first validation study of the finasteride-adjusted Prostate Cancer Prevention Trial Prostate Cancer Risk Calculator (finPCPTRC) in a contemporary referral population in Mexico. 837 patients referred to the Instituto Nacional de Cancerología, Mexico City, Mexico, between 2005 and 2009 were used to validate the finPCPTRC by examining various measures of discrimination and calibration. Net benefit curve analysis was used to gain insight into the use of the finPCPTRC for clinical decisions. Prostate cancer (PCa) incidence (72.8%) was high in this Mexican referral cohort and 45.7% of men who were diagnosed with PCa had high-grade lesions (HGPCa, Gleason score >6). 1.3% of the patients were taking finasteride. The finPCPTRC was a superior diagnostic tool compared to prostate-specific antigen alone when discriminating patients with PCa from those without PCa (AUC = 0.784 vs. AUC = 0.687, p < 0.001) and when discriminating patients with HGPCa from those without HGPCa (AUC = 0.768 vs. AUC = 0.739, p < 0.001). The finPCPTRC underestimated the risk of PCa but overestimated the risk of HGPCa (both p < 0.001). Compared with other strategies to opt for biopsy, the net benefit would be larger with utilization of the finPCPTRC for patients accepting higher risks of HGPCa. Rates of biopsy-detectable PCa and HGPCa were high and 1.3% of this referral cohort in Mexico was taking finasteride. The risks of PCa or HGPCa calculated by the finPCPTRC were not well calibrated for this referral Mexican population and new clinical diagnostic tools are needed. Copyright © 2012 S. Karger AG, Basel.

FIN-EPOS - Finnish national initiative of the European Plate Observing System: Bringing Finnish solid Earth infrastructures into EPOS

NASA Astrophysics Data System (ADS)

Vuorinen, Tommi; Korja, Annakaisa

2017-04-01

FIN-EPOS consortium is a joint community of Finnish national research institutes tasked with operating and maintaining solid-earth geophysical and geological observatories and laboratories in Finland. These national research infrastructures (NRIs) seek to join EPOS research infrastructure (EPOS RI) and further pursue Finland's participation as a founding member in EPOS ERIC (European Research Infrastructure Consortium). Current partners of FIN-EPOS are the University of Helsinki (UH), the University of and Oulu (UO), Finnish Geospatial Research Institute (FGI) of the National Land Survey (NLS), Finnish Meteorological Institute (FMI), Geological Survey of Finland (GTK), CSC - IT Center for Science and MIKES Metrology at VTT Technical Research Centre of Finland Ltd. The consortium is hosted by the Institute of Seismology, UH (ISUH). The primary purpose of the consortium is to act as a coordinating body between various NRIs and the EPOS RI. FIN-EPOS engages in planning and development of the national EPOS RI and will provide support in EPOS implementation phase (IP) for the partner NRIs. FIN-EPOS also promotes the awareness of EPOS in Finland and is open to new partner NRIs that would benefit from participating in EPOS. The consortium additionally seeks to advance solid Earth science education, technologies and innovations in Finland and is actively engaging in Nordic co-operation and collaboration of solid Earth RIs. The main short term objective of FIN-EPOS is to make Finnish geoscientific data provided by NRIs interoperable with the Thematic Core Services (TCS) in the EPOS IP. Consortium partners commit into applying and following metadata and data format standards provided by EPOS. FIN-EPOS will also provide a national Finnish language web portal where users are identified and their user rights for EPOS resources are defined.

Recent Improvements to the Finite-Fault Rupture Detector Algorithm: FinDer II

NASA Astrophysics Data System (ADS)

Smith, D.; Boese, M.; Heaton, T. H.

2015-12-01

Constraining the finite-fault rupture extent and azimuth is crucial for accurately estimating ground-motion in large earthquakes. Detecting and modeling finite-fault ruptures in real-time is thus essential to both earthquake early warning (EEW) and rapid emergency response. Following extensive real-time and offline testing, the finite-fault rupture detector algorithm, FinDer (Böse et al., 2012 & 2015), was successfully integrated into the California-wide ShakeAlert EEW demonstration system. Since April 2015, FinDer has been scanning real-time waveform data from approximately 420 strong-motion stations in California for peak ground acceleration (PGA) patterns indicative of earthquakes. FinDer analyzes strong-motion data by comparing spatial images of observed PGA with theoretical templates modeled from empirical ground-motion prediction equations (GMPEs). If the correlation between the observed and theoretical PGA is sufficiently high, a report is sent to ShakeAlert including the estimated centroid position, length, and strike, and their uncertainties, of an ongoing fault rupture. Rupture estimates are continuously updated as new data arrives. As part of a joint effort between USGS Menlo Park, ETH Zurich, and Caltech, we have rewritten FinDer in C++ to obtain a faster and more flexible implementation. One new feature of FinDer II is that multiple contour lines of high-frequency PGA are computed and correlated with templates, allowing the detection of both large earthquakes and much smaller (~ M3.5) events shortly after their nucleation. Unlike previous EEW algorithms, FinDer II thus provides a modeling approach for both small-magnitude point-source and larger-magnitude finite-fault ruptures with consistent error estimates for the entire event magnitude range.

A large new subset of TRIM genes highly diversified by duplication and positive selection in teleost fish

PubMed Central

van der Aa, Lieke M; Levraud, Jean-Pierre; Yahmi, Malika; Lauret, Emilie; Briolat, Valérie; Herbomel, Philippe; Benmansour, Abdenour; Boudinot, Pierre

2009-01-01

Background In mammals, the members of the tripartite motif (TRIM) protein family are involved in various cellular processes including innate immunity against viral infection. Viruses exert strong selective pressures on the defense system. Accordingly, antiviral TRIMs have diversified highly through gene expansion, positive selection and alternative splicing. Characterizing immune TRIMs in other vertebrates may enlighten their complex evolution. Results We describe here a large new subfamily of TRIMs in teleosts, called finTRIMs, identified in rainbow trout as virus-induced transcripts. FinTRIMs are formed of nearly identical RING/B-box regions and C-termini of variable length; the long variants include a B30.2 domain. The zebrafish genome harbors a striking diversity of finTRIMs, with 84 genes distributed in clusters on different chromosomes. A phylogenetic analysis revealed different subsets suggesting lineage-specific diversification events. Accordingly, the number of fintrim genes varies greatly among fish species. Conserved syntenies were observed only for the oldest fintrims. The closest mammalian relatives are trim16 and trim25, but they are not true orthologs. The B30.2 domain of zebrafish finTRIMs evolved under strong positive selection. The positions under positive selection are remarkably congruent in finTRIMs and in mammalian antiviral TRIM5α, concentrated within a viral recognition motif in mammals. The B30.2 domains most closely related to finTRIM are found among NOD-like receptors (NLR), indicating that the evolution of TRIMs and NLRs was intertwined by exon shuffling. Conclusion The diversity, evolution, and features of finTRIMs suggest an important role in fish innate immunity; this would make them the first TRIMs involved in immunity identified outside mammals. PMID:19196451

Differential regulation of msx genes in the development of the gonopodium, an intromittent organ, and of the "sword," a sexually selected trait of swordtail fishes (Xiphophorus).

PubMed

Zauner, Hans; Begemann, Gerrit; Marí-Beffa, Manuel; Meyer, Axel

2003-01-01

The possession of a conspicuous extension of colored ventral rays of the caudal fin in male fish of swordtails (genus Xiphophorus) is a prominent example for a trait that evolved by sexual selection. To understand the evolutionary history of this so-called sword molecularly, it is of interest to unravel the developmental pathways responsible for extended growth of sword rays during development of swordtail males. We isolated two msx genes and showed that they are differentially regulated during sword outgrowth. During sword growth in juvenile males, as well as during testosterone-induced sword development and fin ray regeneration in the sword after amputation, expression of msxC is markedly up-regulated in the sword forming fin rays. In contrast, msxE/1 is not differentially expressed in ventral and dorsal male fin rays, suggesting a link between the development of male secondary sexual characters in fins and up-regulation of msxC expression. In addition, we showed that msx gene expression patterns differ significantly between Xiphophorus and zebrafish. We also included in our study the gonopodium, a testosterone-dependent anal fin modification that serves as a fertilization organ in males of live-bearing fishes. Our finding that increased levels of msxC expression are associated with the testosterone-induced outgrowth of the gonopodium might suggest either that at least parts of the signaling pathways that pattern the evolutionary older gonopodium have been coopted to evolve a sexually selected innovation such as the sword or that increased msxC expression may be inherent to the growth process of long fin rays in general.

Thermal regulation for APDs in a 1 mm(3) resolution clinical PET camera: design, simulation and experimental verification.

PubMed

Zhai, Jinjian; Vandenbroucke, Arne; Levin, Craig S

2014-07-21

We are developing a 1 mm(3) resolution positron emission tomography camera dedicated to breast imaging. The camera collects high energy photons emitted from radioactively labeled agents introduced in the patients in order to detect molecular signatures of breast cancer. The camera comprises many layers of lutetium yttrium oxyorthosilicate (LYSO) scintillation crystals coupled to position sensitive avalanche photodiodes (PSAPDs). The main objectives of the studies presented in this paper are to investigate the temperature profile of the layers of LYSO-PSAPD detectors (a.k.a. 'fins') residing in the camera and to use these results to present the design of the thermal regulation system for the front end of the camera. The study was performed using both experimental methods and simulation. We investigated a design with a heat-dissipating fin. Three fin configurations are tested: fin with Al windows (FwW), fin without Al windows (FwoW) and fin with alumina windows (FwAW). A Fluent® simulation was conducted to study the experimentally inaccessible temperature of the PSAPDs. For the best configuration (FwW), the temperature difference from the center to a point near the edge is 1.0 K when 1.5 A current was applied to the Peltier elements. Those of FwoW and FwAW are 2.6 K and 1.7 K, respectively. We conclude that the design of a heat-dissipating fin configuration with 'aluminum windows' (FwW) that borders the scintillation crystal arrays of 16 adjacent detector modules has better heat dissipation capabilities than the design without 'aluminum windows' (FwoW) and the design with 'alumina windows' (FwAW), respectively.

Evaluation of coded wire tags for marking lake trout

USGS Publications Warehouse

Elrod, Joseph H.; Schneider, Clifford P.

1986-01-01

Among hatchery-reared lake trout (Salvelinus namaycush) of the 1979-1982 year classes stocked in New York waters of Lake Ontario, more than 3 million fish were marked with a coded wire tag (CWT) plus an adipose fin clip, and 1.5 million with only conventional fin clips. Altogether, 7,640 tags were recovered from fish collected with bottom trawls and gill nets or caught by anglers during 1980-1983. One person was able to extract and decipher 200 or more CWTs per day with about a 1% error rate in reading and recording codes. Presence of the CWT did not affect growth. The adipose fin clip did not regenerate. The occurrence of fish with an adipose fin clip but no CWT resulted primarily from the regeneration of paired fins among fish marked with a combination of the adipose fin and a paired fin. Loss of CWTs between marking and stocking (generally 4-5 months for fish stocked in spring and 1-8 d for fish stocked in fall) declined from nearly 11% for the 1979 year class stocked as fall fingerlings to less than 3% for the 1981 and 1982 year classes - a difference that primarily reflected improvements in instrumentation and tagging technique. The rate of CWT loss after the marked fish were stocked was probably less than 1% per year. The CWT is a reliable method for marking hatchery-reared lake trout. A large number of experimental groups can be uniquely marked, and fish from each group can be accurately identified throughout their life. Use of this technique should greatly facilitate evaluations of genetic strain, hatchery experience, condition at time of stocking, season of stocking, size at stocking, method of stocking and other factors that affect poststocking survival and performance of lake trout stocked in the Great Lakes.

Fixture for multiple-FCC chemical stripping and plating

NASA Technical Reports Server (NTRS)

Angele, W.; Norton, W. E.

1971-01-01

For chemical stripping, lead tape applied near ends to be stripped protects insulation. Taped ends are submerged half way in stripping solution. For electroplating, both ends of FCC are stripped - top ends for electric contact, others for submersion in electroplating solution.

Filmwise Condensation of Steam on Externally-Finned Horizontal Tubes.

DTIC Science & Technology

1983-12-01

via gravity to the boiler. The auxiliary condenser was constructed of two 9.5-mm (3/8-in) water- cooled ccpper lines helically coiled to a height of...34. " . .. . ’ . .- .. ’. .. .- . . . i . ’ -, - NPS69-83-003 - m NAVAL POSTGRADUATE SCHOOL Monterey, California THESIS FILMWISE CONDENSATION OF STEAM ON EXTERNALLY-FINNED...and SubEtee) 5. TYPE OF REPORT & PERIOD COVERED Filmwise Condensation of Steam on Master Thesis; Externally-Finned Horizontal Tubes D e r1 6

Blue and Fin Whale Habitat Modeling from Long-Term Year-Round Passive Acoustic Data from the Southern California Bight

DTIC Science & Technology

2014-09-30

be used for habitat modeling include sea surface temperature (SST), sea surface height (SSH), chlorophyll a concentration, and primary production...1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Blue and Fin Whale Habitat Modeling from Long-Term Year...predictive, year-round habitat models of the presence of calling blue and fin whales in the Southern California Bight, to facilitate Navy’s operational

Computational Fluid Dynamics (CFD) Simulations of a Finned Projectile with Microflaps for Flow Control

DTIC Science & Technology

2016-04-01

fields associated with these control mechanisms for US Army weapons are complex, involving 3-dimensional (3-D) shock- boundary layer interactions...distribution over the rear finned section and thus produce control forces and moments. Dykes et al.6 used a flat - plate fin interaction design of...cells—tetrahedrals, triangular prisms, and pyramids—were used in the mesh. Grid points shown in Fig. 3a were clustered in the boundary layer region

A wind-tunnel investigation of parameters affecting helicopter directional control at low speeds in ground effect

NASA Technical Reports Server (NTRS)

Yeager, W. T., Jr.; Young, W. H., Jr.; Mantay, W. R.

1974-01-01

An investigation was conducted in the Langley full-scale tunnel to measure the performance of several helicopter tail-rotor/fin configurations with regard to directional control problems encountered at low speeds in ground effect. Tests were conducted at wind azimuths of 0 deg to 360 deg in increments of 30 deg and 60 deg and at wind speeds from 0 to 35 knots. The results indicate that at certain combinations of wind speed and wind azimuth, large increases in adverse fin force require correspondingly large increases in the tail-rotor thrust, collective pitch, and power required to maintain yaw trim. Changing the tail-rotor direction of rotation to top blade aft for either a pusher tail rotor (tail-rotor wake blowing away from fin) or a tractor tail rotor (tail-rotor wake blowing against fin) will alleviate this problem. For a pusher tail rotor at 180 deg wind azimuth, increases in the fin/tail-rotor gap were not found to have any significant influence on the overall vehicle directional control capability. Changing the tail rotor to a higher position was found to improve tail-rotor performance for a fin-off configuration at a wind azimuth of 180 deg. A V-tail configuration with a pusher tail rotor with top blade aft direction of rotation was found to be the best configuration with regard to overall directional control capability.

Collagen IX is required for the integrity of collagen II fibrils and the regulation of vascular plexus formation in Zebrafish caudal fins

PubMed Central

Huang, Cheng-chen; Wang, Tai-Chuan; Lin, Bo-Hung; Wang, Yi-Wen; Johnson, Stephen L.; Yu, John

2013-01-01

Capillary plexuses form during both vasculogenesis and angiogenesis and are remodeled into mature vessel types and patterns which are delicately orchestrated with the sizes and shapes of other tissues and organs. We isolated a zebrafish mutation named prp (for persistent plexus) that causes persistent formation of vascular plexuses in the caudal fins and consequent mispatterning of bony fin rays and the fin shape. Detailed analyses revealed that the prp mutation causes a significant reduction in the size and dramatic structural defects in collagen II-rich extracellular matrices called actinotrichia of both embryonic finfolds and adult fins. prp was mapped to chromosome 19 and found to encode the zebrafish collagen9α1 (col9α1) gene which is abundantly expressed in developing finfolds. A point mutation resulting in a leucine-to-histidine change was detected in the thrombospondin domain of the col9α1 gene in prp. Morpholino-mediated knockdown of col9α1 phenocopied the prp small-finfold phenotype in wild-type embryos, and an injection of plasmids containing the col9α1 cDNA into prp embryos locally restored the finfold size. Furthermore, we found that osteoblasts in prp mutants were mispatterned apparently following the abnormal vascular plexus pattern, demonstrating that blood vessels play an important role in the patterning of bony rays in zebrafish caudal fins. PMID:19501583

Collagen IX is required for the integrity of collagen II fibrils and the regulation of vascular plexus formation in zebrafish caudal fins.

PubMed

Huang, Cheng-chen; Wang, Tai-Chuan; Lin, Bo-Hung; Wang, Yi-Wen; Johnson, Stephen L; Yu, John

2009-08-15

Capillary plexuses form during both vasculogenesis and angiogenesis and are remodeled into mature vessel types and patterns which are delicately orchestrated with the sizes and shapes of other tissues and organs. We isolated a zebrafish mutation named prp (for persistent plexus) that causes persistent formation of vascular plexuses in the caudal fins and consequent mispatterning of bony fin rays and the fin shape. Detailed analyses revealed that the prp mutation causes a significant reduction in the size and dramatic structural defects in collagen II-rich extracellular matrices called actinotrichia of both embryonic finfolds and adult fins. prp was mapped to chromosome 19 and found to encode the zebrafish collagen9alpha1 (col9alpha1) gene which is abundantly expressed in developing finfolds. A point mutation resulting in a leucine-to-histidine change was detected in the thrombospondin domain of the col9alpha1 gene in prp. Morpholino-mediated knockdown of col9alpha1 phenocopied the prp small-finfold phenotype in wild-type embryos, and an injection of plasmids containing the col9alpha1 cDNA into prp embryos locally restored the finfold size. Furthermore, we found that osteoblasts in prp mutants were mispatterned apparently following the abnormal vascular plexus pattern, demonstrating that blood vessels play an important role in the patterning of bony rays in zebrafish caudal fins.

Habitat of calling blue and fin whales in the Southern California Bight

NASA Astrophysics Data System (ADS)

Sirovic, A.; Chou, E.; Roch, M. A.

2016-02-01

Northeast Pacific blue whale B calls and fin whale 20 Hz calls were detected from passive acoustic data collected over seven years at 16 sites in the Southern California Bight (SCB). Calling blue whales were most common in the coastal areas, during the summer and fall months. Fin whales began calling in fall and continued through winter, in the southcentral SCB. These data were used to develop habitat models of calling blue and fin whales in areas of high and low abundance in the SCB, using remotely sensed variables such as sea surface temperature, sea surface height, chlorophyll a, and primary productivity as model covariates. A random forest framework was used for variable selection and generalized additive models were developed to explain functional relationships, evaluate relative contribution of each significant variable, and investigate predictive abilities of models of calling whales. Seasonal component was an important feature of all models. Additionally, areas of high calling blue and fin whale abundance both had a positive relationship with the sea surface temperature. In areas of lower abundance, chlorophyll a concentration and primary productivity were important variables for blue whale models and sea surface height and primary productivity were significant covariates in fin whale models. Predictive models were generally better for predicting general trends than absolute values, but there was a large degree of variation in year-to-year predictability across different sites.

Saurida lessepsianus a new species of lizardfish (Pisces: Synodontidae) from the Red Sea and Mediterranean Sea, with a key to Saurida species in the Red Sea.

PubMed

Russell, Barry C; Golani, Daniel; Tikochinski, Yaron

2015-05-12

Saurida lessepsianus n. sp., a lizardfish (Aulopiformes: Synodontidae) from the Red Sea and Mediterranean Sea, previously misidentified as S. undosquamis (Richardson) and more recently as S. macrolepis Tanaka, is described as a new species. It is characterised by the following combination of characters: dorsal fin with 11-12 rays; pectoral fins with 13-15 rays; lateral-line scales 47-51; transverse scale rows above lateral line 4½, below lateral line 5½; pectoral fins moderately long (extending to between just before or just beyond a line from origin of pelvic fins to origin of dorsal fin); 2 rows of teeth on outer palatines; 0-2 teeth on vomer; tongue with 3-6 rows of teeth posteriorly; caudal peduncle slightly compressed (depth a little more than width); upper margin of caudal fin with row of 3-8 (usually 6 or 7) small black spots; stomach pale grey to blackish anteriorly; intestine whitish. The species is common in the Red Sea and as a result of Lessepsian migration through the Suez Canal, it is now widely distributed in the eastern Mediterranean. The taxonomic status of two other Red Sea nominal species, Saurus badimottah Rüppell [= Saurida tumbil (Bloch)] and Saurida sinaitica Dollfus in Gruvel (a nomen nudum), is clarified. A key is provided for the species of Saurida in the Red Sea.

Retinoic Acid Is Involved in the Metamorphosis of the Anal Fin into an Intromittent Organ, the Gonopodium, in the Green Swordtail (Xiphophorus hellerii)

PubMed Central

Meyer, Axel; Begemann, Gerrit

2013-01-01

In poeciliid fish the male anal fin has been transformed into a gonopodium, an intromittent organ required for internal fertilization. Elevated testosterone levels induce metamorphosis of a subset of anal fin rays to grow and form the specialized terminal structures of the gonopodium. The molecular mechanisms underlying these processes are largely unknown. Here, we investigated whether retinoic acid (RA) signaling is involved in gonopodium development in the swordtail Xiphophorus hellerii. We showed that aldh1a2, a RA synthesizing enzyme, and the RA receptors, rar-ga and rar-gb, are expressed in anal fins during metamorphosis. aldh1a2 expression is regulated by testosterone in a concentration-dependent manner and is up-regulated in both hormone-induced and naturally developing gonopodia. Androgen receptor (ar), a putative regulator of gonopodial development, is co-expressed with aldh1a2 and the RA receptors in gonopodial rays. Importantly, experimental increase of RA signaling promoted growth of the gonopodium and increased the number of new segments. Based on gene expression analyses and pharmacological manipulation of gonopodium development, we show that the RA signaling pathway is activated in response to androgen signaling and promotes fin ray growth and development during the metamorphosis of the anal fin into the gonopodium. PMID:24204880

Selective epitaxial growth properties and strain characterization of Si1- x Ge x in SiO2 trench arrays

NASA Astrophysics Data System (ADS)

Koo, Sangmo; Jang, Hyunchul; Ko, Dae-Hong

2017-04-01

In this study, we investigated the formation of a Si1- x Ge x fin structure in SiO2 trench arrays via an ultra-high-vacuum chemical-vapor deposition (UHV-CVD) selective epitaxial growth (SEG) process. Defect generation and microstructures of Si1- x Ge x fin structures with different Ge concentrations ( x = 0.2, 0.3 and 0.45) were examined. In addition, the strain evolution of a Si1- x Ge x fin structure was analyzed by using reciprocal space mapping (RSM). An (111) facet was formed from the Si1- x Ge x epi-layer and SiO2 trench wall interface to minimize the interface and the surface energy. The Si1- x Ge x fin structures were fully relaxed along the direction perpendicular to the trenches regardless of the Ge concentration. On the other hand, the fin structures were fully or partially strained along the direction parallel to the trenches depending on the Ge concentration: fully strained Si0.8Ge0.2 and Si0.7Ge0.3, and a Si0.55Ge0.45 strain-relaxed buffer. We further confirmed that the strain on the Si1- x Ge x fin structures remained stable after oxide removal and H2/N2 post-annealing.

Pethia sanjaymoluri, a new species of barb (Teleostei: Cyprinidae) from the northern Western Ghats, India.

PubMed

Katwate, U; Jadhav, S; Kumkar, P; Raghavan, R; Dahanukar, N

2016-05-01

Pethia sanjaymoluri, a new cyprinid, is described from the Pavana and Nira tributaries of Bhima River, Krishna drainage, Maharashtra, India. It can be distinguished from congeners by a combination of characteristics that includes an incomplete lateral line, absence of barbels, upper lip thick and fleshy, 23-25 lateral series scales, 7-12 lateral-line pored scales, 10 predorsal scales, 11-14 prepelvic scales, 17-20 pre-anal scales, 4½ scales between dorsal-fin origin and lateral line, four scales between lateral line and pelvic-fin origin, 8-15 pairs of serrae on distal half of dorsal-fin spine, 12-14 branched pectoral-fin rays, 4 + 26 total vertebrae, 4 + 5 predorsal vertebrae, 4 + 13 abdominal vertebrae, 13 caudal vertebrae and a unique colour pattern comprising a humeral spot positioned below the lateral line and encompassing the third and fourth lateral-line scales and one scale below, one caudal spot on 17th-21st lateral-line scales with a yellow hue on its anterior side and apical half of dorsal fin studded with melanophores making the fin tip appear black. Genetic analysis based on the mitochondrial cytochrome b gene sequence suggests that the species is distinct from other known species of Pethia for which data are available. © 2016 The Fisheries Society of the British Isles.

Expression of Hsp70 reveals significant differences between fin regeneration and inflammation in Paramisgurnus dabryanus.

PubMed

Li, Li; Wang, Linlin; He, Jingya; Chang, Zhongjie

2017-05-01

Hsp70 is the most strongly induced in response to various cellular stresses and a good candidate for investigating its role in tissue injury. We firstly cloned full-length cDNA of hsp70 from Paramisgurnus dabryanus (PdHsp70) by RACE method (GenBank: KP402408.1). Then regeneration and inflammation of fin were established by amputation and scratch respectively. Quantitative RT-PCR detected the PdHsp70 began to increase rapidly its expression at 1 days post amputation (dpa) and reached the peak at 2 dpa during fin regeneration. Its expression was also up-regulated at 2 days post scratch (dps) of inflammation but still significant weaker in comparison with it in regenerated fin at 2 dpa. Next, immunohistochemistry analysis of PdHsp70 showed that PdHsp70 located mainly in the deeper epidermis of regenerated fin and was stronger than its expression in the scratched inflammatory fin which was involved in whole epidermal. SDS-PAGE and Western blotting confirmed that the PdHsp70 protein expressed efficiently in Escherichia coli BL21. These findings have implied that PdHsp70 are implicated in different regulation of regeneration and inflammation in response to injury stimulation. During the regeneration, it is involved in the formation of wound epidermis by mediating cellular protection whereas it can modulate inflammatory by activating the innate immune response. Copyright © 2017. Published by Elsevier Ltd.

A Novel Mini-DNA Barcoding Assay to Identify Processed Fins from Internationally Protected Shark Species

PubMed Central

Fields, Andrew T.; Abercrombie, Debra L.; Eng, Rowena; Feldheim, Kevin; Chapman, Demian D.

2015-01-01

There is a growing need to identify shark products in trade, in part due to the recent listing of five commercially important species on the Appendices of the Convention on International Trade in Endangered Species (CITES; porbeagle, Lamna nasus, oceanic whitetip, Carcharhinus longimanus scalloped hammerhead, Sphyrna lewini, smooth hammerhead, S. zygaena and great hammerhead S. mokarran) in addition to three species listed in the early part of this century (whale, Rhincodon typus, basking, Cetorhinus maximus, and white, Carcharodon carcharias). Shark fins are traded internationally to supply the Asian dried seafood market, in which they are used to make the luxury dish shark fin soup. Shark fins usually enter international trade with their skin still intact and can be identified using morphological characters or standard DNA-barcoding approaches. Once they reach Asia and are traded in this region the skin is removed and they are treated with chemicals that eliminate many key diagnostic characters and degrade their DNA (“processed fins”). Here, we present a validated mini-barcode assay based on partial sequences of the cytochrome oxidase I gene that can reliably identify the processed fins of seven of the eight CITES listed shark species. We also demonstrate that the assay can even frequently identify the species or genus of origin of shark fin soup (31 out of 50 samples). PMID:25646789

The Finnish disease heritage database (FinDis) update-a database for the genes mutated in the Finnish disease heritage brought to the next-generation sequencing era.

PubMed

Polvi, Anne; Linturi, Henna; Varilo, Teppo; Anttonen, Anna-Kaisa; Byrne, Myles; Fokkema, Ivo F A C; Almusa, Henrikki; Metzidis, Anthony; Avela, Kristiina; Aula, Pertti; Kestilä, Marjo; Muilu, Juha

2013-11-01

The Finnish Disease Heritage Database (FinDis) (http://findis.org) was originally published in 2004 as a centralized information resource for rare monogenic diseases enriched in the Finnish population. The FinDis database originally contained 405 causative variants for 30 diseases. At the time, the FinDis database was a comprehensive collection of data, but since 1994, a large amount of new information has emerged, making the necessity to update the database evident. We collected information and updated the database to contain genes and causative variants for 35 diseases, including six more genes and more than 1,400 additional disease-causing variants. Information for causative variants for each gene is collected under the LOVD 3.0 platform, enabling easy updating. The FinDis portal provides a centralized resource and user interface to link information on each disease and gene with variant data in the LOVD 3.0 platform. The software written to achieve this has been open-sourced and made available on GitHub (http://github.com/findis-db), allowing biomedical institutions in other countries to present their national data in a similar way, and to both contribute to, and benefit from, standardized variation data. The updated FinDis portal provides a unique resource to assist patient diagnosis, research, and the development of new cures. © 2013 WILEY PERIODICALS, INC.

Pre-electrospray ionisation manifold methylation and post-electrospray ionisation manifold cleavage/ion cluster formation observed during electrospray ionisation of chloramphenicol in solutions of methanol and acetonitrile for liquid chromatography-mass spectrometry employing a commercial quadrupole ion trap mass analyser.

PubMed

Sichilongo, Kwenga F; Famuyiwa, Samson O; Kibechu, Rose

2011-01-01

We have observed unusual mass spectra of chloramphenicol (CAP) in solutions of methanol or acetonitrile showing intense ions at m/z 297, m/z 311, m/z 325 and m/z 339. The observed ions were different from those which are traditionally observed in the full scan ESI mass spectra of CAP with ions of m/z 321, m/z 323 and m/z 325. We have evidence to show that this process starts with offline methylation of CAP in solutions of methanol or acetonitrile to give m/z 339. Investigations using nuclear magnetic resonance (NMR) spectroscopy showed that there is a methylene group somewhere within the CAP molecule but not attached to any of the carbon atoms when the CAP is dissolved in methanol or acetonitrile before infusion into the mass spectrometer. The possible locations of attachment were speculated to be the electronegative atoms apart from the chlorine atoms due to valence considerations. The methylene group is attached to the nitrogen atom and forms a bond as observed in the MS/MS spectra of m/z 297, m/z 311, m/z 325 and m/z 339 which give m/z 183 as the base peak in all cases. Further experiments showed that there is cleavage of the methylated CAP molecule followed by cluster ion formation involving addition of methylene groups to the CAP fragment with m/z 183 to produce ions of m/z including m/z 297, m/z 311, m/z 325 and m/z 339. This process occurs in the mass spectrometer in the region housing the tube lens and is triggered when the ions are accelerated through this region by application of a negative tube lens offset voltage. This region affords collision of the charged droplets with a collision gas in this case nitrogen to strip the droplets of their solvent molecules. Experiments to follow the intensities of m/z 183, m/z 311, m/z 321, m/z 323, m/z 325 and m/z 339 as the tube lens offset voltage was varied were done in which the intensities of m/z 311, m/z 325 and m/z 339 were observed to be at their peak when the tube lens offset voltage was set at -40 V. When the tube lens offset voltage is swung to +40 V, thus decelerating the ions through the capillary skimmer region via the tube lens, the traditionally observed spectra with m/z 321, m/z 323 and m/z 325 were observed.

Damage tolerance of woven graphite-epoxy buffer strip panels

NASA Technical Reports Server (NTRS)

Kennedy, John M.

1990-01-01

Graphite-epoxy panels with S glass buffer strips were tested in tension and shear to measure their residual strengths with crack-like damage. The buffer strips were regularly spaced narrow strips of continuous S glass. Panels were made with a uniweave graphite cloth where the S glass buffer material was woven directly into the cloth. Panels were made with different width and thickness buffer strips. The panels were loaded to failure while remote strain, strain at the end of the slit, and crack opening displacement were monitoring. The notched region and nearby buffer strips were radiographed periodically to reveal crack growth and damage. Except for panels with short slits, the buffer strips arrested the propagating crack. The strength (or failing strain) of the panels was significantly higher than the strength of all-graphite panels with the same length slit. Panels with wide, thick buffer strips were stronger than panels with thin, narrow buffer strips. A shear-lag model predicted the failing strength of tension panels with wide buffer strips accurately, but over-estimated the strength of the shear panels and the tension panels with narrow buffer strips.

Review on Enhanced Heat Transfer Techniques using Modern Technologies for 4S Air Cooled Engines

NASA Astrophysics Data System (ADS)

Ramasubramanian, S.; Bupesh Raja, V. K.

2017-05-01

Engine performance is a biggest challenge and a vital area of concern when it comes to automobiles. Researchers across the globe have been working decades together meticulously improvising the performance of engine in terms of efficiency. The durability of the engine components mainly depends on the thermal stress it undergoes over the period of operation. Air cooling of engine is the simplest and most desirous technique that has been adopted for ages. In this regard fins or extended surfaces are employed for effective cooling of the cylinder while in operation. The conductive and convective heat transfer rate from the cylinder to the fins and in turn from the fins to surrounding ambience determines the effective performance of the engine. In this paper an attempt is made to review and summarize the various researches that were conducted on the Fins in terms of profile geometry, number of fins, size, thickness factor, material used etc., and to bring about a long term solution with the modern technologies like nano coatings and nano materials.

Design and dynamic modeling of electrorheological fluid-based variable-stiffness fin for robotic fish

NASA Astrophysics Data System (ADS)

Bazaz Behbahani, Sanaz; Tan, Xiaobo

2017-08-01

Fish actively control their stiffness in different swimming conditions. Inspired by such an adaptive behavior, in this paper we study the design, prototyping, and dynamic modeling of compact, tunable-stiffness fins for robotic fish, where electrorheological (ER) fluid serves as the enabling element. A multi-layer composite fin with an ER fluid core is prototyped and utilized to investigate the influence of electrical field on its performance. Hamilton's principle is used to derive the dynamic equations of motion of the flexible fin, and Lighthill's large-amplitude elongated-body theory is adopted to estimate the hydrodynamic force when the fin undergoes base-actuated rotation. The dynamic equations are then discretized using the finite element method, to obtain an approximate numerical solution. Experiments are conducted on the prototyped flexible ER fluid-filled beam for parameter identification and validation of the proposed model, and for examining the effectiveness of electrically controlled stiffness tuning. In particular, it is found that the natural frequency is increased by almost 40% when the applied electric field changes from 0 to 1.5× {10}6 {{V}} {{{m}}}-1.

20-Hz pulses and other vocalizations of fin whales, Balaenoptera physalus, in the Gulf of California, Mexico.

PubMed

Thompson, P O; Findley, L T; Vidal, O

1992-12-01

Low-frequency vocalizations were recorded from fin whales, Balaenoptera physalus, in the Gulf of California, Mexico, during three cruises. In March 1985, recorded 20-Hz pulses were in sequences of regular 9-s interpulse intervals. In August 1987, nearly all were in sequences of doublets with alternating 5- and 18-s interpulse intervals. No 20-Hz pulse sequences of any kind were detected in February 1987. The typical pulse modulated from 42 to 20 Hz and its median duration was 0.7 s (1985 data). Most other fin whale sounds were also short tonal pulses averaging 82, 56, and 68 Hz, respectively, for the three cruises; 89% were modulated in frequency, mostly downward. Compared to Atlantic and Pacific Ocean regions, Gulf of California 20-Hz pulses were unique in terms of frequency modulation, interpulse sound levels, and temporal patterns. Fin whales in the Gulf may represent a regional stock revealed by their sound characteristics, a phenomenon previously shown for humpback whales, birds, and fish. Regional differences in fin whale sounds were found in comparisons of Atlantic and Pacific locations.

Three-dimensional numerical study of heat transfer enhancement in separated flows

NASA Astrophysics Data System (ADS)

Kumar, Saurav; Vengadesan, S.

2017-11-01

The flow separation appears in a wide range of heat transfer applications and causes poor heat transfer performance. It motivates the study of heat transfer enhancement in laminar as well as turbulent flows over a backward facing step by means of an adiabatic fin mounted on the top wall. Recently, we have studied steady, 2-D numerical simulations in laminar flow and investigated the effect of fin length, location, and orientation. It revealed that the addition of fin causes enhancement of heat transfer and it is very effective to control the flow and thermal behavior. The fin is most effective and sensitive when it is placed exactly above the step. A slight displacement of the fin in upstream of the step causes the complete change of flow and thermal behavior. Based on the obtained 2-D results it is interesting to investigate the side wall effect in three-dimensional simulations. The comparison of two-dimensional and three-dimensional numerical simulations with the available experimental results will be presented. Special attention has to be given to capture unsteadiness in the flow and thermal field.

Scatterometry-based metrology for SAQP pitch walking using virtual reference

NASA Astrophysics Data System (ADS)

Kagalwala, Taher; Vaid, Alok; Mahendrakar, Sridhar; Lenahan, Michael; Fang, Fang; Isbester, Paul; Shifrin, Michael; Etzioni, Yoav; Cepler, Aron; Yellai, Naren; Dasari, Prasad; Bozdog, Cornel

2016-03-01

Advanced technology nodes, 10nm and beyond, employing multi-patterning techniques for pitch reduction pose new process and metrology challenges in maintaining consistent positioning of structural features. Self-Aligned Quadruple Patterning (SAQP) process is used to create the Fins in FinFET devices with pitch values well below optical lithography limits. The SAQP process bares compounding effects from successive Reactive Ion Etch (RIE) and spacer depositions. These processes induce a shift in the pitch value from one fin compared to another neighboring fin. This is known as pitch walking. Pitch walking affects device performance as well as later processes which work on an assumption that there is consistent spacing between fins. In SAQP there are 3 pitch walking parameters of interest, each linked to specific process steps in the flow. These pitch walking parameters are difficult to discriminate at a specific process step by singular evaluation technique or even with reference metrology such as Transmission Electron Microscopy (TEM). In this paper we will utilize a virtual reference to generate a scatterometry model to measure pitch walk for SAQP process flow.

Measuring self-aligned quadruple patterning pitch walking with scatterometry-based metrology utilizing virtual reference

NASA Astrophysics Data System (ADS)

Kagalwala, Taher; Vaid, Alok; Mahendrakar, Sridhar; Lenahan, Michael; Fang, Fang; Isbester, Paul; Shifrin, Michael; Etzioni, Yoav; Cepler, Aron; Yellai, Naren; Dasari, Prasad; Bozdog, Cornel

2016-10-01

Advanced technology nodes, 10 nm and beyond, employing multipatterning techniques for pitch reduction pose new process and metrology challenges in maintaining consistent positioning of structural features. A self-aligned quadruple patterning (SAQP) process is used to create the fins in FinFET devices with pitch values well below optical lithography limits. The SAQP process bears the compounding effects from successive reactive ion etch and spacer depositions. These processes induce a shift in the pitch value from one fin compared to another neighboring fin. This is known as pitch walking. Pitch walking affects device performance as well as later processes, which work on an assumption that there is consistent spacing between fins. In SAQP, there are three pitch walking parameters of interest, each linked to specific process steps in the flow. These pitch walking parameters are difficult to discriminate at a specific process step by singular evaluation technique or even with reference metrology, such as transmission electron microscopy. We will utilize a virtual reference to generate a scatterometry model to measure pitch walk for SAQP process flow.

Harnessing Active Fins to Segregate Nanoparticles from Binary Mixtures

NASA Astrophysics Data System (ADS)

Liu, Ya; Kuksenok, Olga; Bhattacharya, Amitabh; Ma, Yongting; He, Ximin; Aizenberg, Joanna; Balazs, Anna

2014-03-01

One of the challenges in creating high-performance polymeric nanocomposites for optoelectronic applications, such as bilayer solar cells, is establishing effective and facile routes for controlling the properties of interface and segregation of binary particles with hole conductor particles and electron conductor particles. We model nanocomposites that encompass binary particles and binary blends in a microchannel. An array of oscillating microfins is immersed in the fluid and tethered to the floor of the microchannel; the fluid containing mixture of nanoparticles is driven along the channel by an imposed pressure gradient. During the oscillations, the fins with the specific chemical wetting reach the upper fluid when they are upright and are entirely within the lower stream when they are tilted. We introduce specific interaction between the fins and particulates in the solution. Fins can selectively ``catch'' target nanoparticles within the upper fluid stream and then release them into the lower stream. We focus on different modes of fins motion to optimize selective segregation of particles within binary mixture. Our approach provides an effective means of tailoring the properties and ultimate performance of the composites.