Damage to offshore infrastructure in the Gulf of Mexico by hurricanes Katrina and Rita

NASA Astrophysics Data System (ADS)

Cruz, A. M.; Krausmann, E.

2009-04-01

The damage inflicted by hurricanes Katrina and Rita to the Gulf-of-Mexico's (GoM) oil and gas production, both onshore and offshore, has shown the proneness of industry to Natech accidents (natural hazard-triggered hazardous-materials releases). In order to contribute towards a better understanding of Natech events, we assessed the damage to and hazardous-materials releases from offshore oil and natural-gas platforms and pipelines induced by hurricanes Katrina and Rita. Data was obtained through a review of published literature and interviews with government officials and industry representatives from the affected region. We also reviewed over 60,000 records of reported hazardous-materials releases from the National Response Center's (NRC) database to identify and analyze the hazardous-materials releases directly attributed to offshore oil and gas platforms and pipelines affected by the two hurricanes. Our results show that hurricanes Katrina and Rita destroyed at least 113 platforms, and severely damaged at least 53 others. Sixty percent of the facilities destroyed were built 30 years ago or more prior to the adoption of the more stringent design standards that went into effect after 1977. The storms also destroyed 5 drilling rigs and severely damaged 19 mobile offshore drilling units (MODUs). Some 19 MODUs lost their moorings and became adrift during the storms which not only posed a danger to existing facilities but the dragging anchors also damaged pipelines and other infrastructure. Structural damage to platforms included toppling of sections, and tilting or leaning of platforms. Possible causes for failure of structural and non-structural components of platforms included loading caused by wave inundation of the deck. Failure of rigs attached to platforms was also observed resulting in significant damage to the platform or adjacent infrastructure, as well as damage to equipment, living quarters and helipads. The failures are attributable to tie-down components and occurred on both fixed and floating platforms. The total number of pipelines damaged by Hurricanes Katrina and Rita as of May 1, 2006, was 457. Pipeline damage was mostly caused by damage or failure of the host platform or its development and production piping, the impact of dragging and displaced objects, and pipeline interaction at a crossing. Damage to pipelines was a major contributing factor in delaying start up of offshore oil and gas production. During our analysis of the NRC database we identified 611 reported hazardous-materials releases directly attributed to offshore platforms and pipelines affected by the two hurricanes. There were twice as many releases during Hurricane Katrina than during Rita; 80% or more of the releases reported in the NRC database occurred from platforms. Our analysis suggests that the majority of releases were petroleum products, such as crude oil and condensate, followed by natural gas. In both Katrina and Rita, releases were more likely in the front, right quadrant of the storm. Storm-surge values were highest closer to the coastline. This may help explain the higher number of releases in shallow waters. The higher number of hazardous-materials releases from platforms during Katrina may partly be attributed to the higher wind speeds for this storm as it approached land.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rashid, A.; Nygaard, C.

The use of concrete in marine environment has gained tremendous popularity in the past decade and is continued to be a very popular material for marine industry in the world today. It has a very diversified use from large offshore platforms and floating structures in the North Sea, Canada and South America to offshore loading terminals and junction platforms in shallow waters in the marshes of southern Louisiana in the Gulf of Mexico. Also, precast concrete sections are extensively used all over the world in the construction of marine structures. Because of their large variety of shapes and sizes, theymore » can be tailored to fit multiple applications in marine environment. The added quality control in the fabrication yard and the ease of installation by lifting makes them a very attractive option. The use of precast concrete sections is gaining a lot of popularity in South America. A lot of fabrication yards are manufacturing these sections locally. There are hundreds of offshore concrete platforms utilizing these sections in Lake Maracaibo, Venezuela. The paper discusses the use of concrete for offshore structures including floaters. It describes some general concepts and advantages to be gained by the use of concrete (precast and cast-in-place) in marine environment. It also discusses some general design considerations required for the use of different types of precast concrete sections that can be utilized for oil and gas platforms and loading terminals. Lastly the paper describes some typical examples of concrete platforms built out of concrete piles, precast concrete girders and beam sections and concrete decking.« less

Floating Offshore Wind in Hawaii: Potential for Jobs and Economic Impacts from Three Future Scenarios

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jimenez, Tony; Keyser, David; Tegen, Suzanne

Construction of the first offshore wind power plant in the United States began in 2015, off the coast of Rhode Island, using fixed platform structures that are appropriate for shallow seafloors, like those located off the East Coast and mid-Atlantic. However, floating platforms, which have yet to be deployed commercially, will likely need to be anchored to the deeper seafloor if deployed in Hawaiian waters. To analyze the employment and economic potential for floating offshore wind off Hawaii's coasts, the Bureau of Ocean Energy Management commissioned the National Renewable Energy Laboratory (NREL) to analyze two hypothetical deployment scenarios for Hawaii:more » 400 MW of offshore wind by 2050 and 800 MW of offshore wind by 2050. The results of this analysis can be used to better understand the general scale of economic opportunities that could result from offshore wind development.« less

Review and Recommendations for the Interagency Ship Structure Committee’s Fiscal 1984 Research Program,

DTIC Science & Technology

1983-01-01

Daily. Proposal Evaluation Procedure Organizations interested in doing the work adverstised submit proposals and cost estimates. The USCG contracting...types of offshore structures. These structures have largely been fixed platforms for petroleum drilling and production, and mobile offshore drilling...structures and of those mobile drilling units that are bottom supported, such as jack-ups and submersibles. Structures which are held in place by anchors

Issues in offshore platform research - Part 1: Semi-submersibles

NASA Astrophysics Data System (ADS)

Sharma, R.; Kim, Tae-Wan; Sha, O. P.; Misra, S. C.

2010-09-01

Availability of economic and efficient energy resources is crucial to a nation's development. Because of their low cost and advancement in drilling and exploration technologies, oil and gas based energy systems are the most widely used energy source throughout the world. The inexpensive oil and gas based energy systems are used for everything, i.e., from transportation of goods and people to the harvesting of crops for food. As the energy demand continues to rise, there is strong need for inexpensive energy solutions. An offshore platform is a large structure that is used to house workers and machinery needed to drill wells in the ocean bed, extract oil and/or natural gas, process the produced fluids, and ship or pipe them to shore. Depending on the circumstances, the offshore platform can be fixed (to the ocean floor) or can consist of an artificial island or can float. Semi-submersibles are used for various purposes in offshore and marine engineering, e.g. crane vessels, drilling vessels, tourist vessels, production platforms and accommodation facilities, etc. The challenges of deepwater drilling have further motivated the researchers to design optimum choices for semi-submersibles for a chosen operating depth. In our series of eight papers, we discuss the design and production aspects of all the types of offshore platforms. In the present part I, we present an introduction and critical analysis of semi-submersibles.

Determination of current loads of floating platform for special purposes

NASA Astrophysics Data System (ADS)

Ma, Guang-ying; Yao, Yun-long; Zhao, Chen-yao

2017-08-01

This article studied a new floating offshore platform for special purposes, which was assembled by standard floating modules. The environmental load calculation of the platform is an important part of the research of the ocean platform, which has always been paid attention to by engineers. In addition to wave loads, the wind loads and current loads are also important environmental factors that affect the dynamic response of the offshore platform. The current loads on the bottom structure should not be ignored. By Fluent software, the hydrostatic conditions and external current loads of the platform were calculated in this paper. The coefficient which is independent of the current velocity, namely, current force coefficient, can be fitted through current loads, which can be used for the consequent hydrodynamic and mooring analyses.

Motion performance and mooring system of a floating offshore wind turbine

NASA Astrophysics Data System (ADS)

Zhao, Jing; Zhang, Liang; Wu, Haitao

2012-09-01

The development of offshore wind farms was originally carried out in shallow water areas with fixed (seabed mounted) structures. However, countries with limited shallow water areas require innovative floating platforms to deploy wind turbines offshore in order to harness wind energy to generate electricity in deep seas. The performances of motion and mooring system dynamics are vital to designing a cost effective and durable floating platform. This paper describes a numerical model to simulate dynamic behavior of a new semi-submersible type floating offshore wind turbine (FOWT) system. The wind turbine was modeled as a wind block with a certain thrust coefficient, and the hydrodynamics and mooring system dynamics of the platform were calculated by SESAM software. The effect of change in environmental conditions on the dynamic response of the system under wave and wind loading was examined. The results indicate that the semi-submersible concept has excellent performance and SESAM could be an effective tool for floating wind turbine design and analysis.

Analysis of offshore platforms lifting with fixed pile structure type (fixed platform) based on ASD89

NASA Astrophysics Data System (ADS)

Sugianto, Agus; Indriani, Andi Marini

2017-11-01

Platform construction GTS (Gathering Testing Sattelite) is offshore construction platform with fix pile structure type/fixed platform functioning to support the mining of petroleum exploitation. After construction fabrication process platform was moved to barges, then shipped to the installation site. Moving process is generally done by pull or push based on construction design determined when planning. But at the time of lifting equipment/cranes available in the work area then the moving process can be done by lifting so that moving activity can be implemented more quickly of work. This analysis moving process of GTS platform in a different way that is generally done to GTS platform types by lifting using problem is construction reinforcement required, so the construction can be moved by lifting with analyzing and checking structure working stress that occurs due to construction moving process by lifting AISC code standard and analysis using the SAP2000 structure analysis program. The analysis result showed that existing condition cannot be moved by lifting because stress ratio is above maximum allowable value that is 0.950 (AISC-ASD89). Overstress occurs on the member 295 and 324 with stress ratio value 0.97 and 0.95 so that it is required structural reinforcement. Box plate aplication at both members so that it produces stress ratio values 0.78 at the member 295 and stress ratio of 0.77 at the member 324. These results indicate that the construction have qualified structural reinforcement for being moved by lifting.

Measurement and Analysis of Extreme Wave and Ice Actions in the Great Lakes for Offshore Wind Platform Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

England, Tony; van Nieuwstadt, Lin; De Roo, Roger

This project, funded by the Department of Energy as DE-EE0005376, successfully measured wind-driven lake ice forces on an offshore structure in Lake Superior through one of the coldest winters in recent history. While offshore regions of the Great Lakes offer promising opportunities for harvesting wind energy, these massive bodies of freshwater also offer extreme and unique challenges. Among these challenges is the need to anticipate forces exerted on offshore structures by lake ice. The parameters of interest include the frequency, extent, and movement of lake ice, parameters that are routinely monitored via satellite, and ice thickness, a parameter that hasmore » been monitored at discrete locations over many years and is routinely modeled. Essential relationships for these data to be of use in the design of offshore structures and the primary objective of this project are measurements of maximum forces that lake ice of known thicknesses might exert on an offshore structure.« less

Historical Population Estimates For Several Fish Species At Offshore Oil and Gas Structures in the US Gulf of Mexico

NASA Astrophysics Data System (ADS)

Gitschlag, G.

2016-02-01

Population estimates were calculated for four fish species occurring at offshore oil and gas structures in water depths of 14-32 m off the Louisiana and upper Texas coasts in the US Gulf of Mexico. From 1993-1999 sampling was conducted at eight offshore platforms in conjunction with explosive salvage of the structures. To estimate fish population size prior to detonation of explosives, a fish mark-recapture study was conducted. Fish were captured on rod and reel using assorted hook sizes. Traps were occasionally used to supplement catches. Fish were tagged below the dorsal fin with plastic t-bar tags using tagging guns. Only fish that were alive and in good condition were released. Recapture sampling was conducted after explosives were detonated during salvage operations. Personnel operating from inflatable boats used dip nets to collect all dead fish that floated to the surface. Divers collected representative samples of dead fish that sank to the sea floor. Data provided estimates for red snapper (Lutjanus campechanus), Atlantic spadefish (Chaetodipterus faber), gray triggerfish (Balistes capriscus), and blue runner (Caranx crysos) at one or more of the eight platforms studied. At seven platforms, population size for red snapper was calculated at 503-1,943 with a 95% CI of 478. Abundance estimates for Atlantic spadefish at three platforms ranged from 1,432-1,782 with a 95% CI of 473. At three platforms, population size of gray triggerfish was 63-129 with a 95% CI of 82. Blue runner abundance at one platform was 558. Unlike the other three species which occur close to the platforms, blue runner range widely and recapture of this species was dependent on fish schools being in close proximity to the platform at the time explosives were detonated. Tag recapture was as high as 73% for red snapper at one structure studied.

Oil rigs and offshore sport fishing in Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dugas, R.; Guillory, V.; Fischer, M.

Forty years ago, offshore sport fishing in Louisiana was almost nonexistent. Offshore oil drilling platforms are the primary cause of the present increase in sport fishing in this area. Algae and other organisms forming the first step in the food chain cluster around the subsurface structures of the rigs, attracting fish that seek food and shelter. Major game species frequenting these rigs are identified. (3 photos, 22 references, 2 tables)

RADIATION DOSE AND RISK TO RECREATIONAL FISHERMEN FROM INGESTION OF FISH CAUGHT NEAR EIGHT OIL PLATFORMS IN THE GULF OF MEXICO

DOE Office of Scientific and Technical Information (OSTI.GOV)

MEINHOLD,A.F.; HOLTZMAN,S.

1998-06-01

Offshore production of oil and gas is accompanied by a saline wastewater, called produced water. Produced water discharges to the Gulf of Mexico often contain elevated concentrations of radionuclides that occur naturally in the geologic reservoir along with the oil and gas. These radionuclides may accumulate in organisms that live near offshore oil and gas structures. Because recreational fishing in the Gulf of Mexico is concentrated near oil and gas platforms, there is the potential for increased risks to recreational fishermen from the ingestion of radionuclides in fish caught near produced water discharges. This analysis investigated the potential risk tomore » recreational fishermen from radium and lead-210 in offshore produced water discharges to the Gulf of Mexico. The assessment used data collected at eight discharging offshore platforms and two reference locations. These data were collected in a USDOE funded project titled ``Environmental and Economic Assessment of Discharges from Gulf of Mexico Region Oil and Gas Operations'', here called the USDOE Field Study. The risk assessments were done to support risk managers in developing regulations and permits for offshore discharges of produced water.« less

30 CFR 250.915 - What are the CVA's primary responsibilities?

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Platforms and Structures... or organizations acting as CVAs must not function in any capacity that would create a conflict of... design, fabrication and installation of the platform. ...

Design of self-contained sensor for monitoring of deep-sea offshore platform

NASA Astrophysics Data System (ADS)

Song, Yang; Yu, Yan; Zhang, Chunwei; Dong, Weijie; Ou, Jinping

2013-04-01

Offshore platform, which is the base of the production and living in the sea, is the most important infrastructure for developing oil and gas resources. At present, there are almost 6500 offshore platforms servicing in the 53 countries' sea areas around the world, creating great wealth for the world. In general, offshore platforms may work for 20 years, however, offshore platforms are expensive, complex, bulky, and so many of them are on extended active duty. Because of offshore platforms servicing in the harsh marine environment for a long time, the marine environment have a great impact on the offshore platforms. Besides, with the impact and erosion of seawater, and material aging, the offshore platform is possible to be in unexpected situations when a badly sudden situation happens. Therefore, it is of great significance to monitor the marine environment and offshore platforms. The self-contained sensor for deep-sea offshore platform with its unique design, can not only effectively extend the working time of the sensor with the capability of converting vibration energy to electrical energy, but also simultaneously collect the data of acceleration, inclination, temperature and humidity of the deep sea, so that we can achieve the purpose of monitoring offshore platforms through analyzing the collected data. The self-contained sensor for monitoring of deep-sea offshore platform includes sensing unit, data collecting and storage unit, the energy supply unit. The sensing unit with multi-variables, consists of an accelerometer LIS344ALH, an inclinometer SCA103T and a temperature and humidity sensor SHT11; the data collecting and storage unit includes the MSP430 low-power MCU, large capacity memory, clock circuit and the communication interface, the communication interface includes USB interface, serial ports and wireless interface; in addition, the energy supply unit, converting vibration to electrical energy to power the overall system, includes the electromagnetic generator, voltage multiplier circuit and a super capacitor which can withstand virtually unlimited number of charge-discharge cycles. When the seawater impacts on offshore platforms to produce vibration, electromagnetic generator converts vibration to electrical energy, its output(~ 1 V 50 Hz AC) is stepped up and rectified by a voltage multiplier circuit, and the energy is stored in a super capacitor. It is controlled by the MSP430 that monitors the voltage level on the super capacitor. The super capacitor charges the Li-ion battery when the voltage on the super capacitor reaches a threshold, then the whole process of energy supply is completed. The self-contained sensor for deep-sea offshore platform has good application prospects and practical value with small size, low power, being easy to install, converting vibration energy to supply power and high detection accuracy.

Study on dynamic characteristics of hydraulic pumping unit on offshore platform

NASA Astrophysics Data System (ADS)

Chang, Zong-yu; Yu, Yan-qun; Qi, Yao-guang

2017-12-01

A new technology of offshore oil rod pumping production is developed for offshore heavy oil recovery. A new type of miniature hydraulic pumping unit with long-stroke, low pumping speed and compact structure is designed based on the spatial characteristics of offshore platforms. By combining the strengths of sinusoidal velocity curve and trapezoidal velocity curve, a kinematical model of the acceleration, the velocity and displacement of the pumping unit's hanging point is established. The results show that the pumping unit has good kinematic characteristics of smooth motion and small dynamic load. The multi-degree-of-freedom dynamic model of the single-well pumping unit is established. The first and second order natural frequencies of the sucker rod string subsystem and the pumping unit subsystem are studied. The results show that the first and the second order natural frequencies among the pumping rod string, pumping unit-platform subsystem and the dynamic excitation have differences over 5 times from each other, indicating that resonance phenomenon will not appear during the operation and the dynamic requirements for field use are met in the system.

Stress state reassessment of Romanian offshore structures taking into account corrosion influence

NASA Astrophysics Data System (ADS)

Joavină, R.; Zăgan, S.; Zăgan, R.; Popa, M.

2017-08-01

Progressive degradation analysis for extraction or exploration offshore structure, with appraisal of failure potential and the causes that can be correlated with the service age, depends on the various sources of uncertainty that require particular attention in design, construction and exploitation phases. Romanian self erecting platforms are spatial lattice structures consist of tubular steel joints, forming a continuous system with an infinite number of dynamic degrees of freedom. Reassessment of a structure at fixed intervals of time, recorrelation of initial design elements with the actual situation encountered in location and with structural behaviour represents a major asset in lowering vulnerabilities of offshore structure. This paper proposes a comparative reassessment of the stress state for an offshore structure Gloria type, when leaving the shipyard and at the end of that interval corresponding to capital revision, taking into account sectional changes due to marine environment corrosion. The calculation was done using Newmark integration method on a 3D model, asses of the dynamic loads was made through probabilistic spectral method.

Radiation dose and risk to recreational fishermen from ingestion of fish caught near eight oil platforms in the Gulf of Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meinhold, A.F.; Holtzman, S.

1998-06-01

Offshore production of oil and gas is accompanied by a saline wastewater, called produced water. Produced water discharges to the Gulf of Mexico often contain elevated concentrations of radionuclides that occur naturally in the geologic reservoir along with the oil and gas. These radionuclides may accumulate in organisms that live near offshore oil and gas structures. Because recreational fishing in the Gulf of Mexico is concentrated near oil and gas platforms, there is the potential for increased risks to recreational fishermen from the ingestion of radionuclides in fish caught near produced water discharges. This analysis investigated the potential risk tomore » recreational fishermen from radium and lead-210 in offshore produced water discharged to the Gulf of Mexico.« less

Remocean : a marine radar as a safety tool for offshore platforms

NASA Astrophysics Data System (ADS)

Serafino, Francesco; Ludeno, Giovanni; Arturi, Daniele; Lugni, Claudio; Natale, Antonio; Soldovieri, Francesco

2013-04-01

In the recent years, there is a growing interest towards offshore platforms for electric power energy with a focus to the ones exploiting wind or sea surface currents force. In this frame, an important role can be played the marine X-band radar systems, which are able to acquire high resolution information (of the order of the meters) on the sea state (direction and height of the waves) and sea surface current in a range of several kilometers from the radar platform. The information gained from the radar is therefore very useful for many issues related to the offshore platforms installation and safety. In fact, the X-band radar system can be deployed to gain a long-term information about the direction and the velocity of sea surface current so to drive in a proper way the installation of the turbines by choosing the right areas; to use the information about the long-term sea state monitoring to evaluate the vulnerability of the platforms not only against the extreme climate events but also against the structural solicitation due to ordinary conditions; to gain indirect information about the wind intensity and direction for the right management of the wind farms. In this work, we will present the marine radar system designed and developed by REMOCEAN (www.remocean.com), a Spin-off of the National Research Council (CNR, Italy). In particular, we will present the application of the REMOCEAN system to the case of the monitoring of the sea state for the offshore platform safety in real conditions.

Ecological and political issues surrounding decommissioning of offshore oil facilities in the Southern California Bight

USGS Publications Warehouse

Schroeder, Donna M.; Love, Milton S.

2004-01-01

To aid legislators, resource managers, and the general public, this paper summarizes and clarifies some of the issues and options that the federal government and the state of California face in decommissioning offshore oil and gas production platforms, particularly as these relate to platform ecology. Both local marine ecology and political climate play a role in decommissioning offshore oil production platforms. Compared to the relatively supportive political climate in the Gulf of Mexico for “rigs-to-reefs” programs, conflicting social values among stakeholders in Southern California increases the need for understanding ecological impacts of various decommissioning alternatives (which range from total removal to allowing some or all of platform structure to remain in the ocean). Additional scientific needs in the decommissioning process include further assessment of platform habitat quality, estimation of regional impacts of decommissioning alternatives to marine populations, and determination of biological effects of any residual contaminants. The principal management need is a ranking of environmental priorities (e.g. species-of-interest and marine habitats). Because considerable numbers of economically important species reside near oil platforms, National Oceanic and Atmospheric Administration Fisheries should consider the consequences of decommissioning alternatives in their overall management plans. Management strategies could include designating reefed platforms as marine protected areas. The overarching conclusion from both ecological and political perspectives is that decommissioning decisions should be made on a case-by-case basis.

The ARGO Project: assessing NA-TECH risks on off-shore oil platforms

NASA Astrophysics Data System (ADS)

Capuano, Paolo; Basco, Anna; Di Ruocco, Angela; Esposito, Simona; Fusco, Giannetta; Garcia-Aristizabal, Alexander; Mercogliano, Paola; Salzano, Ernesto; Solaro, Giuseppe; Teofilo, Gianvito; Scandone, Paolo; Gasparini, Paolo

2017-04-01

ARGO (Analysis of natural and anthropogenic risks on off-shore oil platforms) is a 2 years project, funded by the DGS-UNMIG (Directorate General for Safety of Mining and Energy Activities - National Mining Office for Hydrocarbons and Georesources) of Italian Ministry of Economic Development. The project, coordinated by AMRA (Center for the Analysis and Monitoring of Environmental Risk), aims at providing technical support for the analysis of natural and anthropogenic risks on offshore oil platforms. In order to achieve this challenging objective, ARGO brings together climate experts, risk management experts, seismologists, geologists, chemical engineers, earth and coastal observation experts. ARGO has developed methodologies for the probabilistic analysis of industrial accidents triggered by natural events (NA-TECH) on offshore oil platforms in the Italian seas, including extreme events related to climate changes. Furthermore the environmental effect of offshore activities has been investigated, including: changes on seismicity and on the evolution of coastal areas close to offshore platforms. Then a probabilistic multi-risk framework has been developed for the analysis of NA-TECH events on offshore installations for hydrocarbon extraction.

Floating Offshore Wind in California: Gross Potential for Jobs and Economic Impacts from Two Future Scenarios

DOE Office of Scientific and Technical Information (OSTI.GOV)

Speer, Bethany; Keyser, David; Tegen, Suzanne

Construction of the first offshore wind farm in the United States began in 2015, using fixed platform structures that are appropriate for shallow seafloors, like those located off of the East Coast and mid-Atlantic. However, floating platforms, which have yet to be deployed commercially, will likely need to anchor to the deeper seafloor if deployed off of the West Coast. To analyze the employment and economic potential for floating offshore wind along the West Coast, the Bureau of Ocean Energy Management (BOEM) has commissioned the National Renewable Energy Laboratory (NREL) to analyze two hypothetical, large-scale deployment scenarios for California: 16more » GW of offshore wind by 2050 (Scenario A) and 10 GW of offshore wind by 2050 (Scenario B). The results of this analysis can be used to better understand the general scales of economic opportunities that could result from offshore wind development. Results show total state gross domestic product (GDP) impacts of $16.2 billion in Scenario B or $39.7 billion in Scenario A for construction; and $3.5 billion in Scenario B or $7.9 billion in Scenario A for the operations phases.« less

Evaluating stress analysis and failure criteria for offshore structures for Pechora Sea conditions

NASA Astrophysics Data System (ADS)

Nesic, S.; Donskoy, Y.; Zolotukhin, A.

2017-12-01

Development of Arctic hydrocarbon resources has faced many challenges due to sensitive environmental conditions including low temperatures, ice cover and terrestrial permafrost and extreme seasonal variation in sunlight. Russian offshore field development in Arctic region is usually associated with annual ice cover, which can cause serious damage on the offshore platforms. The Pechora Sea has claimed as one of the most perspective oil and gas region of the Russian Arctic with seven discovered oil and gas fields and several dozens of structures. Our rough assessment, based on in-place hydrocarbon volumes and recovery factor evaluation concept, indicates that Pechora Sea alone has in-place volumes amounting to ca. 20 billion barrel oil equivalent (BOE). This quantity is enough to secure produced volumes by 2040 exceeding 3 billion BOE [1] that indicates huge resource potential of the region. The environmental conditions are primarily function of water dynamics and ice cover. The sea is covered by the ice for greatest part of the year. In this article, the ice load simulations were performed using explicit dynamic analysis system in ANSYS software to determine best shape and size of an offshore platform for the Pechora Sea ice conditions. Different gravity based structures (GBS) were analyzed: artificial island, hollow cylindrical and conical concrete structures and four-leg GBS. Relationships between the stress, deformations and time were analyzed and important observations from the simulation results were a basis for selecting the most preferable structures.

Eighteenth annual offshore technology conference. Volume 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1986-01-01

These sixty papers were given at a conference on offshore technology. Topics covered include friction effects of driving piles into sea beds of various compositions, wave forces on offshore platforms, stability, materials testing of various components such as plates, legs, wellheads, pipe joints, and protection of offshore platforms against ice and collision with icebergs.

Sea loads on ships and offshore structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faltinsen, O.

1990-01-01

The book introduces the theory of the structural loading on ships and offshore structures caused by wind, waves and currents, and goes on to describe the applications of this theory in terms of real structures. The main topics described are linear-wave induced motions, loads on floating structures, numerical methods for ascertaining wave induced motions and loads, viscous wave loads and damping, stationkeeping and water impact and entry. The applications of the theoretical principles are introduced with extensive use of exercises and examples. Applications covered include conventional ships, barges, high speed marine vehicles, semisubmersibles, tension leg platforms, moored or dynamic positionedmore » ships, risers, buoys, fishing nets, jacket structures and gravity platforms. One aim of the book is to provide a physical understanding through simplified mathematical models. In this way one can develop analytical tools to evaluate results from test models, full scale trials or computer simulation, and learns which parameters represent the major contributions and influences on sea loads.« less

The Role of Disturbance, Larval Supply, and Native Community on the Establishment of a Non-Native Species on Oil Platforms in the Santa Barbara Channel

NASA Astrophysics Data System (ADS)

Viola, S.; Page, M.; Miller, R. J.; Zaleski, S.; Doheny, B.; Dugan, J.; Schroeder, D. M.

2016-02-01

Disturbance facilitates the establishment of non-native species in a variety of ecosystems. In marine ecosystems, offshore structures, such as oil and gas platforms, provide hard substrate habitat that can be colonized by non-native species. Periodic platform cleaning and storm events are disturbances that remove the attached epibenthic community and may promote the establishment of non-native species. The non-native crustose bryozoan, Watersipora subtorquata (=W. subatra?), has colonized a number of oil platforms in the Santa Barbara Channel. In this study, we experimentally 1) tested the role of disturbance and water depth on the establishment of Watersipora on an offshore platform, 2) explored how larval supply might influence observed patterns, and 3) evaluated the importance of biotic interactions, specifically predation on Watersipora larvae. To attain these objectives, we 1) quantified Watersipora cover in cleared and undisturbed plots, 2) measured monthly variation in larval supply using settlement plates, and 3) deployed tethered live mussels and sealed mussel shells and compared recruitment to these two surfaces. Our results suggest that disturbance greatly enhances the establishment of Watersipora, but that this effect varies with depth and associated larval availability. Additionally, predation of larvae by native suspension feeders appears to limit the recruitment rate of Watersipora. Our findings on the factors influencing the establishment of Watersipora could inform decisions to manage the spread of non-native species to artificial and natural marine habitats, as well as decisions related to the maintenance of offshore structures as artificial reefs.

Fatigue 󈨛. Volume 3,

DTIC Science & Technology

1987-06-01

Corrosion and Cathodic Protection 1169 on Crack Growth in Offshore Platform Steels in Sea Water - EINAR BARDAL The Influence of Crack Conditions on...PROTECTION ON CRACK GROWTH IN OFFSHORE PLATFORM STEELS IN SEA WATER: EINAR BARDAL* Corrosion fatigue of steel for offshore platforms has been studied at...surfaces (6). When results from experiments with natural sea water are compared with corresponding results obtained in synthetic sea water, no significant

Offshore oil platforms and fouling communities in the southern Arabian Gulf (Abu Dhabi).

PubMed

Stachowitsch, Michael; Kikinger, Reinhard; Herler, Jürgen; Zolda, Pamela; Geutebrück, Ernst

2002-09-01

This study examined the fouling organisms on the legs of offshore oil platforms at two sites in the southern Arabian Gulf (offshore Abu Dhabi, United Arab Emirates). 100% of the metal structures was colonized by encrusting organisms. Both the number of individuals and the total biomass tended to decrease with depth. The total weight of dead shells always exceeded that of living organisms. Sessile filter feeders dominated the biomass, whereas small mobile forms had the largest number of individuals. The biomass at the deeper platform (22 m) was dominated by bivalves, barnacles and bryozoans, while polychaetes and amphipods had the greatest number of individuals. Biomass values here ranged from 1 g/0.1 m2 at 20 m to 147 g/0.1 m2 at 5 m; the corresponding individual numbers were 266 (20 m) and 11,814 indiv./0.1 m2 (5 m). The results at the shallower platform (11 m) differed in several respects: barnacles clearly dominated over bivalves, and sponges exceeded byrozoans, while total individual numbers fell due to a decline in polychaete dominance. Biomass values here ranged from 84 g/0.1 m2 at 10 m to 153 g/0.1 m2 at 0 m; the corresponding individual numbers were 695 (10 m) and 3,125 indiv./0.1 m2 (0 m). The potential role of such fouling communities on artificial structures in the Gulf is discussed.

Floating Offshore Wind in Oregon: Potential for Jobs and Economic Impacts from Two Future Scenarios

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jimenez, Tony; Keyser, David; Tegen, Suzanne

Construction of the first offshore wind power plant in the United States began in 2015, off the coast of Rhode Island, using fixed platform structures that are appropriate for shallow seafloors, like those located off of the East Coast and mid-Atlantic. However, floating platforms, which have yet to be deployed commercially, will likely need to anchor to the deeper seafloor if deployed off of the West Coast. To analyze the employment and economic potential for floating offshore wind along the West Coast, the Bureau of Ocean Energy Management (BOEM) commissioned the National Renewable Energy Laboratory (NREL) to analyze two hypothetical,more » large-scale deployment scenarios for Oregon: 5,500 megawatts (MW) of offshore wind deployment in Oregon by 2050 (Scenario A), and 2,900 MW of offshore wind by 2050 (Scenario B). These levels of deployment could power approximately 1,600,000 homes (Scenario A) or 870,000 homes (Scenario B). Offshore wind would contribute to economic development in Oregon in the near future, and more substantially in the long term, especially if equipment and labor are sourced from within the state. According to the analysis, over the 2020-2050 period, Oregon floating offshore wind facilities could support 65,000-97,000 job-years and add $6.8 billion-$9.9 billion to the state GDP (Scenario A).« less

Regulation and policy working group

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-03-01

The potential environmental impact of offshore platform disposal can be illustrated by both the numbers of platforms and the complexity of their abandonment options. Some 7,000 platforms are in place worldwide. In the US, approximately a quarter of the platforms are more than 25 years old and in sight of their end of service. In addition, 22,000 miles of pipeline are located on the Outer Continental Shelf (OCS) in the United States. There are more offshore platforms in the U.S. Gulf of Mexico than in any other single area in the world. It is estimated that between October 1995 andmore » December 2000, approximately 665 of the nearly 3,800 existing structures will be removed. Couple this with the mammoth size, the vagaries of the ocean, and the levels of sometimes conflicting international and federal laws, and the magnitude of the challenge to protect the environment becomes clear. The Offshore International Newsletter (11/06/95) stated, {open_quotes}In three of the last four years, annual Gulf of Mexico platform removals have exceeded installations, a trend that will likely continue.{close_quotes} Between 100 and 150 platforms have been removed from the OCS each year for the past six or seven years. As increasing numbers of wells, pipelines, and platforms are decommissioned and disposed of, it is important that the relevant techniques, policies, and regulations be discussed and evaluated. The goal of this workshop is to facilitate and document this discussion in an open, objective, and inclusive way. Since U.S. practices and policies provide precedents for other countries, international participation is encouraged and anticipated.« less

Oil rigs and offshore sport fishing in Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dugas, R.; Guillory, V.; Fischer, M.

1979-11-01

The environmental effects of Louisiana's offshore oil platforms are discussed with regard to an increase in sport-fishing. The effects upon fish populations, species diversity, underwater habitats, and food chains from the offshore platforms are obtained from several summaries of studies undertaken between 1970-1979. (DS)

30 CFR 250.903 - What records must I keep?

Code of Federal Regulations, 2013 CFR

2013-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Platforms and Structures General... steel brackets, deck stiffeners and secondary braces or beams would not generally be considered primary...

30 CFR 250.903 - What records must I keep?

Code of Federal Regulations, 2014 CFR

2014-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Platforms and Structures General... steel brackets, deck stiffeners and secondary braces or beams would not generally be considered primary...

30 CFR 250.903 - What records must I keep?

Code of Federal Regulations, 2012 CFR

2012-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Platforms and Structures General... steel brackets, deck stiffeners and secondary braces or beams would not generally be considered primary...

Offshore submarine storage facility for highly chilled liquified gases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, S.F.

1982-12-28

Improvements in an offshore platform and submarine storage facility for highly chilled liquified gas, such as liquified natural gas, are disclosed. The improved facility includes an elongated, vertically oriented submerged anchoring frame to which one or more insulated storage tanks are moveably mounted so they can be positioned at a selected depth in the water. The double piston tank is constructed with improved seals to transfer ambient water pressure of the selected depth to the cryogenic liquified gas without intermixture. This transferred pressure at the depth selected aids in maintaining the liquified state of the stored liquified gas. Structural improvementsmore » to the tank facilitating ballasting, locking the double piston cylinders together and further facilitating surface access to the tank for inspection, repairs and removal, and structural improvements to the platform are disclosed.« less

Efficient preliminary floating offshore wind turbine design and testing methodologies and application to a concrete spar design

PubMed Central

Matha, Denis; Sandner, Frank; Molins, Climent; Campos, Alexis; Cheng, Po Wen

2015-01-01

The current key challenge in the floating offshore wind turbine industry and research is on designing economic floating systems that can compete with fixed-bottom offshore turbines in terms of levelized cost of energy. The preliminary platform design, as well as early experimental design assessments, are critical elements in the overall design process. In this contribution, a brief review of current floating offshore wind turbine platform pre-design and scaled testing methodologies is provided, with a focus on their ability to accommodate the coupled dynamic behaviour of floating offshore wind systems. The exemplary design and testing methodology for a monolithic concrete spar platform as performed within the European KIC AFOSP project is presented. Results from the experimental tests compared to numerical simulations are presented and analysed and show very good agreement for relevant basic dynamic platform properties. Extreme and fatigue loads and cost analysis of the AFOSP system confirm the viability of the presented design process. In summary, the exemplary application of the reduced design and testing methodology for AFOSP confirms that it represents a viable procedure during pre-design of floating offshore wind turbine platforms. PMID:25583870

Marine Fouling Assemblages on Offshore Gas Platforms in the Southern North Sea: Effects of Depth and Distance from Shore on Biodiversity.

PubMed

van der Stap, Tim; Coolen, Joop W P; Lindeboom, Han J

2016-01-01

Offshore platforms are known to act as artificial reefs, though there is on-going debate on whether this effect is beneficial or harmful for the life in the surrounding marine environment. Knowing what species exist on and around the offshore platforms and what environmental variables influence this species assemblage is crucial for a better understanding of the impact of offshore platforms on marine life. Information on this is limited for offshore platforms in the southern North Sea. This study aims to fill this gap in our knowledge and to determine how the composition and the abundance of species assemblages changes with depth and along a distance-from-shore gradient. The species assemblages on five offshore gas platforms in the southern North Sea have been inventoried using Remotely Operated Vehicles inspection footage. A total of 30 taxa were identified. A Generalised Additive Model of the species richness showed a significant non-linear relation with water depth (p = 0.001): from a low richness in shallow waters it increases with depth until 15-20 m, after which richness decreases again. Using PERMANOVA, water depth (p≤0.001), community age (p≤0.001) and the interaction between distance from shore and community age (p≤0.001) showed a significant effect on the species assemblages. Future research should focus on the effect additional environmental variables have on the species assemblages.

Risks to offshore installations in Europe due to natural hazards

NASA Astrophysics Data System (ADS)

Necci, Amos; Krausmann, Elisabeth

2017-04-01

Natural hazards, such as storms, earthquakes, or lightning are a major threat to industry. In particular, chemical plants, storage facilities, pipelines, and offshore oil and gas facilities are vulnerable to natural events which can cause hazardous materials releases and thereby endanger workers, the population and the environment. These technological accidents are commonly referred to as Natech accidents. Recent events have increased concerns about safety in the offshore oil and gas sector, and the need for improving knowledge on the matter has become evident. With those premises, we analyzed accidents, near misses and accident precursors at offshore facilities in Europe caused by natural events using both a statistical and a qualitative approach. For this purpose, we screened the World Offshore Accident Database (WOAD) to identify all incidents that featured natural events as causes or aggravating factors. A dataset of 1,085 global Natech events was built for the statistical analysis. Among those, a subset composed of 303 European records was selected. The results of the analysis showed that offshore Natech events in Europe are frequent; they resulted, however, in low consequences. The main threat to offshore facilities resulted from bad weather, such as strong winds and heavy seas. Storms can put intense loads on the structural parts of offshore installations, eventually exceeding design resistance specifications. Several incidents triggered by lightning strikes and earthquakes were also recorded. Substantial differences in terms of vulnerability, damage modality and consequences emerged between fixed and floating offshore structures. The main damage mode for floating structures was the failure of station keeping systems due to the rupture of mooring or anchors, mainly caused by adverse meteorological conditions. Most of the incidents at fixed offshore structures in Europe involved falling loads for both metal jacket and concrete base platforms due to storms. In contrast, in other parts of the world, and in particular in the Gulf of Mexico, tropical storms are likely to trigger severe direct damage to structures, resulting in platform capsizing, sinking or grounding. The in-depth analysis of the incident records also showed that the natural event was often just the triggering cause of the accident, which was frequently accompanied by contributing factors (e.g. corrosion, fatigue, wrong procedures, etc.). Under these circumstances, not only extreme storms, but also storms with moderate intensity can trigger incidents. Due to the high density of offshore structures and the unique environmental conditions promoting fatigue and corrosion, the North Sea is the area with the highest number of incidents recorded in Europe, as well as the area with the highest number of incidents at semi-submersible units in the world. About 4% of all reported global Natech events at offshore infrastructures involved casualties, and 2.6% for the European incident subset. Hazardous materials releases were documented for 21 events in Europe, resulting in fires and hydrocarbon spills polluting the sea. Furthermore, a surprisingly high number of severe events occurred during towing which highlights the impact of natural hazards on the safety of offshore transfer operations.

Satellite data lift the veil on offshore platforms in the South China Sea

NASA Astrophysics Data System (ADS)

Liu, Yongxue; Sun, Chao; Sun, Jiaqi; Li, Hongyi; Zhan, Wenfeng; Yang, Yuhao; Zhang, Siyu

2016-09-01

Oil and gas exploration in the South China Sea (SCS) has garnered global attention recently; however, uncertainty regarding the accurate number of offshore platforms in the SCS, let alone their detailed spatial distribution and dynamic change, may lead to significant misjudgment of the true status of offshore hydrocarbon production in the region. Using both fresh and archived space-borne images with multiple resolutions, we enumerated the number, distribution, and annual rate of increase of offshore platforms across the SCS. Our results show that: (1) a total of 1082 platforms are present in the SCS, mainly located in shallow-water; and (2) offshore oil/gas exploitation in the SCS is increasing in intensity and advancing from shallow to deep water, and even to ultra-deep-water. Nevertheless, our findings suggest that oil and gas exploration in the SCS may have been over-estimated by one-third in previous reports. However, this overestimation does not imply any amelioration of the potential for future maritime disputes, since the rate of increase of platforms in disputed waters is twice that in undisputed waters.

Satellite data lift the veil on offshore platforms in the South China Sea

PubMed Central

Liu, Yongxue; Sun, Chao; Sun, Jiaqi; Li, Hongyi; Zhan, Wenfeng; Yang, Yuhao; Zhang, Siyu

2016-01-01

Oil and gas exploration in the South China Sea (SCS) has garnered global attention recently; however, uncertainty regarding the accurate number of offshore platforms in the SCS, let alone their detailed spatial distribution and dynamic change, may lead to significant misjudgment of the true status of offshore hydrocarbon production in the region. Using both fresh and archived space-borne images with multiple resolutions, we enumerated the number, distribution, and annual rate of increase of offshore platforms across the SCS. Our results show that: (1) a total of 1082 platforms are present in the SCS, mainly located in shallow-water; and (2) offshore oil/gas exploitation in the SCS is increasing in intensity and advancing from shallow to deep water, and even to ultra-deep-water. Nevertheless, our findings suggest that oil and gas exploration in the SCS may have been over-estimated by one-third in previous reports. However, this overestimation does not imply any amelioration of the potential for future maritime disputes, since the rate of increase of platforms in disputed waters is twice that in undisputed waters. PMID:27641542

Efficient preliminary floating offshore wind turbine design and testing methodologies and application to a concrete spar design.

PubMed

Matha, Denis; Sandner, Frank; Molins, Climent; Campos, Alexis; Cheng, Po Wen

2015-02-28

The current key challenge in the floating offshore wind turbine industry and research is on designing economic floating systems that can compete with fixed-bottom offshore turbines in terms of levelized cost of energy. The preliminary platform design, as well as early experimental design assessments, are critical elements in the overall design process. In this contribution, a brief review of current floating offshore wind turbine platform pre-design and scaled testing methodologies is provided, with a focus on their ability to accommodate the coupled dynamic behaviour of floating offshore wind systems. The exemplary design and testing methodology for a monolithic concrete spar platform as performed within the European KIC AFOSP project is presented. Results from the experimental tests compared to numerical simulations are presented and analysed and show very good agreement for relevant basic dynamic platform properties. Extreme and fatigue loads and cost analysis of the AFOSP system confirm the viability of the presented design process. In summary, the exemplary application of the reduced design and testing methodology for AFOSP confirms that it represents a viable procedure during pre-design of floating offshore wind turbine platforms. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

1:50 Scale Testing of Three Floating Wind Turbines at MARIN and Numerical Model Validation Against Test Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dagher, Habib; Viselli, Anthony; Goupee, Andrew

The primary goal of the basin model test program discussed herein is to properly scale and accurately capture physical data of the rigid body motions, accelerations and loads for different floating wind turbine platform technologies. The intended use for this data is for performing comparisons with predictions from various aero-hydro-servo-elastic floating wind turbine simulators for calibration and validation. Of particular interest is validating the floating offshore wind turbine simulation capabilities of NREL’s FAST open-source simulation tool. Once the validation process is complete, coupled simulators such as FAST can be used with a much greater degree of confidence in design processesmore » for commercial development of floating offshore wind turbines. The test program subsequently described in this report was performed at MARIN (Maritime Research Institute Netherlands) in Wageningen, the Netherlands. The models considered consisted of the horizontal axis, NREL 5 MW Reference Wind Turbine (Jonkman et al., 2009) with a flexible tower affixed atop three distinct platforms: a tension leg platform (TLP), a spar-buoy modeled after the OC3 Hywind (Jonkman, 2010) and a semi-submersible. The three generic platform designs were intended to cover the spectrum of currently investigated concepts, each based on proven floating offshore structure technology. The models were tested under Froude scale wind and wave loads. The high-quality wind environments, unique to these tests, were realized in the offshore basin via a novel wind machine which exhibits negligible swirl and low turbulence intensity in the flow field. Recorded data from the floating wind turbine models included rotor torque and position, tower top and base forces and moments, mooring line tensions, six-axis platform motions and accelerations at key locations on the nacelle, tower, and platform. A large number of tests were performed ranging from simple free-decay tests to complex operating conditions with irregular sea states and dynamic winds.« less

Floating Ocean Platform

DTIC Science & Technology

2003-08-15

floating structures create novel habitats for subtidal epibiota?, MARINE ECOLOGY -PROGRESS SERIES, 43-52 Mar. Ecol.- Prog. Ser., 2002 Vegueria, SFJ Godoy... ECOLOGICAL APPLICATIONS, 350-366 Ecol. Appl., 2000 Niedzwecki, JM van de Lindt, JW Gage, JH Teigen, PS, Design estimates of surface wave interaction with...The ecological effects beyond the offshore platform, Coastal Zone: Proceedings of the Symposium on Coastal and Ocean Management, v 2, n pt2, 1989, p

Response spectrum method for extreme wave loading with higher order components of drag force

NASA Astrophysics Data System (ADS)

Reza, Tabeshpour Mohammad; Mani, Fatemi Dezfouli; Ali, Dastan Diznab Mohammad; Saied, Mohajernasab; Saied, Seif Mohammad

2017-03-01

Response spectra of fixed offshore structures impacted by extreme waves are investigated based on the higher order components of the nonlinear drag force. In this way, steel jacket platforms are simplified as a mass attached to a light cantilever cylinder and their corresponding deformation response spectra are estimated by utilizing a generalized single degree of freedom system. Based on the wave data recorded in the Persian Gulf region, extreme wave loading conditions corresponding to different return periods are exerted on the offshore structures. Accordingly, the effect of the higher order components of the drag force is considered and compared to the linearized state for different sea surface levels. When the fundamental period of the offshore structure is about one third of the main period of wave loading, the results indicate the linearized drag term is not capable of achieving a reliable deformation response spectrum.

Marine Fouling Assemblages on Offshore Gas Platforms in the Southern North Sea: Effects of Depth and Distance from Shore on Biodiversity

PubMed Central

van der Stap, Tim; Coolen, Joop W. P.; Lindeboom, Han J.

2016-01-01

Offshore platforms are known to act as artificial reefs, though there is on-going debate on whether this effect is beneficial or harmful for the life in the surrounding marine environment. Knowing what species exist on and around the offshore platforms and what environmental variables influence this species assemblage is crucial for a better understanding of the impact of offshore platforms on marine life. Information on this is limited for offshore platforms in the southern North Sea. This study aims to fill this gap in our knowledge and to determine how the composition and the abundance of species assemblages changes with depth and along a distance-from-shore gradient. The species assemblages on five offshore gas platforms in the southern North Sea have been inventoried using Remotely Operated Vehicles inspection footage. A total of 30 taxa were identified. A Generalised Additive Model of the species richness showed a significant non-linear relation with water depth (p = 0.001): from a low richness in shallow waters it increases with depth until 15–20 m, after which richness decreases again. Using PERMANOVA, water depth (p≤0.001), community age (p≤0.001) and the interaction between distance from shore and community age (p≤0.001) showed a significant effect on the species assemblages. Future research should focus on the effect additional environmental variables have on the species assemblages. PMID:26745870

An air quality emission inventory of offshore operations for the exploration and production of petroleum by the Mexican oil industry

NASA Astrophysics Data System (ADS)

Villasenor, R.; Magdaleno, M.; Quintanar, A.; Gallardo, J. C.; López, M. T.; Jurado, R.; Miranda, A.; Aguilar, M.; Melgarejo, L. A.; Palmerín, E.; Vallejo, C. J.; Barchet, W. R.

An air quality screening study was performed to assess the impacts of emissions from the offshore operations of the oil and gas exploration and production by Mexican industry in the Campeche Sound, which includes the states of Tabasco and Campeche in southeast Mexico. The major goal of this study was the compilation of an emission inventory (EI) for elevated, boom and ground level flares, processes, internal combustion engines and fugitive emissions. This inventory is so far the most comprehensive emission register that has ever been developed for the Mexican petroleum industry in this area. The EI considered 174 offshore platforms, the compression station at Atasta, and the Maritime Ports at Dos Bocas and Cayo Arcas. The offshore facilities identified as potential emitters in the area were the following: (1) trans-shipment stations, (2) a maritime floating port terminal, (3) drilling platforms, (4) crude oil recovering platforms, (5) crude oil production platforms, (6) linking platforms, (7) water injection platforms, (8) pumping platforms, (9) shelter platforms, (10) telecommunication platforms, (11) crude oil measurement platforms, and (12) flaring platforms. Crude oil storage tanks, helicopters and marine ship tankers were also considered to have an EI accurate enough for air quality regulations and mesoscale modeling of atmospheric pollutants. Historical ambient data measure at two onshore petroleum facilities were analyzed to measure air quality impacts on nearby inhabited coastal areas, and a source-receptor relationship for flares at the Ixtoc marine complex was performed to investigate health-based standards for offshore workers. A preliminary air quality model simulation was performed to observe the transport and dispersion patterns of SO 2, which is the main pollutant emitted from the offshore platforms. The meteorological wind and temperature fields were generated with CALMET, a diagnostic meteorological model that used surface observations and upper air soundings from a 4-day field campaign conducted in February of 1999. The CALMET meteorological output and the generated EI drove the transport and dispersion model, CALPUFF. Model results were compared with SO 2 measurements taken from the monitoring network at Dos Bocas.

[Work-related accidents on oil drilling platforms in the Campos Basin, Rio de Janeiro, Brazil].

PubMed

Freitas, C M; Souza, C A; Machado, J M; Porto, M F

2001-01-01

The offshore oil industry is characterized by complex systems in relation to technology and organization of work. Working conditions are hazardous, resulting in accidents and even occasional full-scale catastrophes. This article is the result of a study on work-related accidents in the offshore platforms in the Campos Basin, Rio de Janeiro State. The primary objective was to provide technical back-up for both workers' representative organizations and public authorities. As a methodology, we attempt to go beyond the immediate causes of accidents and emphasize underlying causes related to organizational and managerial aspects. The sources were used in such a way as to permit classification in relation to the type of incident, technological system, operation, and immediate and underlying causes. The results show the aggravation of safety conditions and the immediate need for public authorities and the offshore oil industry in Brazil to change the methods used to investigate accidents in order to identify the main causes in the organizational and managerial structure of companies.

Proceedings: An international workshop on offshore lease abandonment and platform disposal: Technology, regulation, and environmental effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pulsipher, A.

This Proceedings volume includes papers prepared for an international workshop on lease abandonment and offshore platform disposal. The workshop was held April 15, 16, and 17, 1996, in New Orleans, Louisiana. Included in the volume are several plenary speeches and issue papers. prepared by six working groups, who discussed: Abandoning Wells; Abandoning Pipelines; Removing Facilities; Site Clearance; Habitat Management, Maintenance, and Planning; and Regulation and Policy. Also included are an introduction, an afterword (reprinted with the permission of its author, John Lohrenz), and, as Appendix C, the complete report of the National Research Council Marine Boards An Assessment of Techniquesmore » for Removing Fixed Offshore Structures, around which much of the discussion at the workshop was organized. Short biographies of many speakers, organizers, and chairpersons are included as Appendix A. Appendix B is a list of conference participants. Selected papers have been processes separately for inclusion in the Energy Science and Technology database.« less

30 CFR 250.901 - What industry standards must your platform meet?

Code of Federal Regulations, 2014 CFR

2014-07-01

... Structures for Hurricane Conditions, (as incorporated by reference in § 250.198); (5) API Bulletin 2INT-EX, Interim Guidance for Assessment of Existing Offshore Structures for Hurricane Conditions, (as incorporated by reference in § 250.198); (6) API Bulletin 2INT-MET, Interim Guidance on Hurricane Conditions in...

30 CFR 250.901 - What industry standards must your platform meet?

Code of Federal Regulations, 2013 CFR

2013-07-01

... Structures for Hurricane Conditions, (as incorporated by reference in § 250.198); (5) API Bulletin 2INT-EX, Interim Guidance for Assessment of Existing Offshore Structures for Hurricane Conditions, (as incorporated by reference in § 250.198); (6) API Bulletin 2INT-MET, Interim Guidance on Hurricane Conditions in...

30 CFR 250.901 - What industry standards must your platform meet?

Code of Federal Regulations, 2012 CFR

2012-07-01

... Structures for Hurricane Conditions, (as incorporated by reference in § 250.198); (5) API Bulletin 2INT-EX, Interim Guidance for Assessment of Existing Offshore Structures for Hurricane Conditions, (as incorporated by reference in § 250.198); (6) API Bulletin 2INT-MET, Interim Guidance on Hurricane Conditions in...

Risk-based process safety assessment and control measures design for offshore process facilities.

PubMed

Khan, Faisal I; Sadiq, Rehan; Husain, Tahir

2002-09-02

Process operation is the most hazardous activity next to the transportation and drilling operation on an offshore oil and gas (OOG) platform. Past experiences of onshore and offshore oil and gas activities have revealed that a small mis-happening in the process operation might escalate to a catastrophe. This is of especial concern in the OOG platform due to the limited space and compact geometry of the process area, less ventilation, and difficult escape routes. On an OOG platform, each extra control measure, which is implemented, not only occupies space on the platform and increases congestion but also adds extra load to the platform. Eventualities in the OOG platform process operation can be avoided through incorporating the appropriate control measures at the early design stage. In this paper, the authors describe a methodology for risk-based process safety decision making for OOG activities. The methodology is applied to various offshore process units, that is, the compressor, separators, flash drum and driers of an OOG platform. Based on the risk potential, appropriate safety measures are designed for each unit. This paper also illustrates that implementation of the designed safety measures reduces the high Fatal accident rate (FAR) values to an acceptable level.

Numerical tools to predict the environmental loads for offshore structures under extreme weather conditions

NASA Astrophysics Data System (ADS)

Wu, Yanling

2018-05-01

In this paper, the extreme waves were generated using the open source computational fluid dynamic (CFD) tools — OpenFOAM and Waves2FOAM — using linear and nonlinear NewWave input. They were used to conduct the numerical simulation of the wave impact process. Numerical tools based on first-order (with and without stretching) and second-order NewWave are investigated. The simulation to predict force loading for the offshore platform under the extreme weather condition is implemented and compared.

Offshore Energy Mapping for Northeast Atlantic and Mediterranean: MARINA PLATFORM project

NASA Astrophysics Data System (ADS)

Kallos, G.; Galanis, G.; Spyrou, C.; Kalogeri, C.; Adam, A.; Athanasiadis, P.

2012-04-01

Deep offshore ocean energy mapping requires detailed modeling of the wind, wave, tidal and ocean circulation estimations. It requires also detailed mapping of the associated extremes. An important issue in such work is the co-generation of energy (generation of wind, wave, tides, currents) in order to design platforms on an efficient way. For example wind and wave fields exhibit significant phase differences and therefore the produced energy from both sources together requires special analysis. The other two sources namely tides and currents have different temporal scales from the previous two. Another important issue is related to the estimation of the environmental frequencies in order to avoid structural problems. These are issues studied at the framework of the FP7 project MARINA PLATFORM. The main objective of the project is to develop deep water structures that can exploit the energy from wind, wave, tidal and ocean current energy sources. In particular, a primary goal will be the establishment of a set of equitable and transparent criteria for the evaluation of multi-purpose platforms for marine renewable energy. Using these criteria, a novel system set of design and optimisation tools will be produced addressing new platform design, component engineering, risk assessment, spatial planning, platform-related grid connection concepts, all focussed on system integration and reducing costs. The University of Athens group is in charge for estimation and mapping of wind, wave, tidal and ocean current resources, estimate available energy potential, map extreme event characteristics and provide any additional environmental parameter required.

33 CFR 165.155 - Northville Industries Offshore Platform, Riverhead, Long Island, New York-safety zone.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Platform, Riverhead, Long Island, New York-safety zone. 165.155 Section 165.155 Navigation and Navigable...—safety zone. (a) The following area is established as a safety zone during the specified condition: (1... (LPG) vessel is moored at the Offshore Platform. The safety zone remains in effect until the LPG vessel...

33 CFR 165.155 - Northville Industries Offshore Platform, Riverhead, Long Island, New York-safety zone.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Platform, Riverhead, Long Island, New York-safety zone. 165.155 Section 165.155 Navigation and Navigable...—safety zone. (a) The following area is established as a safety zone during the specified condition: (1... (LPG) vessel is moored at the Offshore Platform. The safety zone remains in effect until the LPG vessel...

Aeroelastic impact of above-rated wave-induced structural motions on the near-wake stability of a floating offshore wind turbine rotor

NASA Astrophysics Data System (ADS)

Rodriguez, Steven; Jaworski, Justin

2017-11-01

The impact of above-rated wave-induced motions on the stability of floating offshore wind turbine near-wakes is studied numerically. The rotor near-wake is generated using a lifting-line free vortex wake method, which is strongly coupled to a finite element solver for kinematically nonlinear blade deformations. A synthetic time series of relatively high-amplitude/high-frequency representative of above-rated conditions of the NREL 5MW referece wind turbine is imposed on the rotor structure. To evaluate the impact of these above-rated conditions, a linear stability analysis is first performed on the near wake generated by a fixed-tower wind turbine configuration at above-rated inflow conditions. The platform motion is then introduced via synthetic time series, and a stability analysis is performed on the wake generated by the floating offshore wind turbine at the same above-rated inflow conditions. The stability trends (disturbance modes versus the divergence rate of vortex structures) of the two analyses are compared to identify the impact that above-rated wave-induced structural motions have on the stability of the floating offshore wind turbine wake.

Application of metal magnetic memory technology on defects detection of jack-up platform

NASA Astrophysics Data System (ADS)

Xu, Changhang; Cheng, Liping; Xie, Jing; Yin, Xiaokang; Chen, Guoming

2016-02-01

Metal magnetic memory test (MMMT), which is an effective way in evaluating early damages of ferrimagnets, can determine the existence of material stresses concentration and premature defects. As one of offshore oil exploration and development equipment, jack-up platform always generate stress concentration during its life-cycle due to complicated loading condition and the hash marine environment, which will decline the bearing capacity and cause serious consequences. The paper conducts in situ experiments of defects detection on some key structural components of jack-up platform using MMMT. The signals acquired by MMM-System are processed for feature extraction to evaluate the severity of structure stress concentration. The results show that the method presented in this paper based on MMMT can provide an effective and convenient way of defect detection and structural health monitoring for Jack-up Platform.

[Reliability and validity of the Occupational Stress Scale for Chinese offshore oil platform workers].

PubMed

Chen, Wei-qing; Huang, Zi-hui; Yu, De-xin; Lin, Yan-zu; Ling, Zhi-ming; Tang, Ji-song

2003-02-01

To evaluate the validity and reliability of the Occupational Stress Scale (OSS) for Chinese offshore oil platform workers. A 51-item self-administered questionnaire developed in the light of Cooper's questionnaire and company's special situation was used to investigate 561 subjects. 51 occupational stress items relating to offshore oil production were subjected to factor analysis, and nine latent factors were identified, which explained 62.5% of the total variance. According to the contents described by the items included in each factor, they were respectively defined as: "the interface between job and family/social life (factor 1)", "career and achievement (factor 2)", "safety (factor 3)", "management problem and relationship with others at work (factor 4)", "physical factors of workplace (factor 5)", "platform living environment (factor 6)", "role in management (factor 7)", "ergonomics (factor 8)" and "organization structure (factor 9)". Significant difference in the score of five factors was observed among 12 different job categories by analysis of variance. After adjusting for potential confounding factors (age, educational level), hierarchical multiple regression analysis indicated that the score of the OSS was significantly and positively correlated with the poor mental health of the workers (P < 0.01). The consistent test between OSS and each factor showed that Cronbach's alpha were 0.72 - 0.91. The OSS is a valid and reliable tool for measuring occupational stress, and can be used to explore occupational stress and its influence on health and safety problems in offshore oil workers.

Oil Industry Aids

NASA Technical Reports Server (NTRS)

1979-01-01

The accompanying photos show two types of offshore oil platforms used by Exxon Corporation. In the upper photo is a leg-supported gravity platform; the other structure is a "jackettype" platform, built in sections, towed to sea and assembled on-site. In construction of platforms like these, Exxon Production Research Company, Houston, Texas, conducts extensive structural investigations of decks, supporting members and other platform components, making use of the NASTRAN @ (NASA Structural Analysis) computer program. NASTRAN is a predictive tool which analyzes a computerized design and reports how the structure will react to a great many conditions it will encounter in its operational environment; in this case, NASTRAN studies the effects of waves, winds, ocean storms and other stress-inducing factors. NASTRAN allows Exxon Production Research to perform more complex and more detailed analysis than was possible with previous programs. The same program has also been used by Exxon Research and Engineering Company, Florham Park, New Jersey, in analysis of pressure vessels, turbine components and composite building boards.

Tectonic framework of Turkish sedimentary basins

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yilmaz, P.O.

1988-08-01

Turkey's exploration potential primarily exists in seven onshore (Southeast Turkey platform, Tauride platform, Pontide platform, East Anatolian platform, Interior, Trace, and Adana) basins and four offshore (Black Sea, Marmara Sea, Aegean Sea, and Mediterranean Sea) regional basins formed during the Mesozoic and Tertiary. The Mesozoic basins are the onshore basins: Southeast Turkey, Tauride, Pontide, East Anatolian, and Interior basins. Due to their common tectonic heritage, the southeast Turkey and Tauride basins have similar source rocks, structural growth, trap size, and structural styles. In the north, another Mesozoic basin, the Pontide platform, has a much more complex history and very littlemore » in common with the southerly basins. The Pontide has two distinct parts; the west has Paleozoic continental basement and the east is underlain by island-arc basement of Jurassic age. The plays are in the upper Mesozoic rocks in the west Pontide. The remaining Mesozoic basins of the onshore Interior and East Anatolian basins are poorly known and very complex. Their source, reservoir, and seal are not clearly defined. The basins formed during several orogenic phases in mesozoic and Tertiary. The Cenozoic basins are the onshore Thrace and Adana basins, and all offshore regional basins formed during Miocene extension. Further complicating the onshore basins evolution is the superposition of Cenozoic basins and Mesozoic basins. The Thrace basin in the northwest and Adana basin in the south both originate from Tertiary extension over Tethyan basement and result in a similar source, reservoir, and seal. Local strike-slip movement along the North Anatolian fault modifies the Thrace basin structures, influencing its hydrocarbon potential.« less

Considerations in evaluating potential socioeconomic impacts of offshore platform decommissioning in California.

PubMed

Kruse, Sarah A; Bernstein, Brock; Scholz, Astrid J

2015-10-01

The 27 oil and gas platforms offshore southern California will eventually reach the end of their useful lifetimes (estimated between 2015 and 2030) and will be decommissioned. Current state and federal laws and regulations allow for alternative uses in lieu of the complete removal required in existing leases. Any decommissioning pathway will create a complex mix of costs, benefits, opportunities, and constraints for multiple user groups. To assist the California Natural Resources Agency in understanding these issues, we evaluated the potential socioeconomic impacts of the 2 most likely options: complete removal and partial removal of the structure to 85 feet below the waterline with the remaining structure left in place as an artificial reef-generally defined as a manmade structure with some properties that mimic a natural reef. We estimated impacts on commercial fishing, commercial shipping, recreational fishing, nonconsumptive boating, and nonconsumptive SCUBA diving. Available data supported quantitative estimates for some impacts, semiquantitative estimates for others, and only qualitative approximations of the direction of impact for still others. Even qualitative estimates of the direction of impacts and of user groups' likely preferred options have been useful to the public and decision makers and provided valuable input to the project's integrative decision model. Uncertainty surrounds even qualitative estimates of the likely direction of impact where interactions between multiple impacts could occur or where user groups include subsets that would experience the same option differently. In addition, we were unable to quantify effects on ecosystem value and on the larger regional ecosystem, because of data gaps on the population sizes and dynamics of key species and the uncertainty surrounding the contribution of platforms to available hard substrate and related natural populations offshore southern California. © 2015 SETAC.

Real-time Monitoring of Subsea Gas Pipelines, Offshore Platforms, and Ship Inspection Scores Using an Automatic Identification System

NASA Astrophysics Data System (ADS)

Artana, K. B.; Pitana, T.; Dinariyana, D. P.; Ariana, M.; Kristianto, D.; Pratiwi, E.

2018-06-01

The aim of this research is to develop an algorithm and application that can perform real-time monitoring of the safety operation of offshore platforms and subsea gas pipelines as well as determine the need for ship inspection using data obtained from automatic identification system (AIS). The research also focuses on the integration of shipping database, AIS data, and others to develop a prototype for designing a real-time monitoring system of offshore platforms and pipelines. A simple concept is used in the development of this prototype, which is achieved by using an overlaying map that outlines the coordinates of the offshore platform and subsea gas pipeline with the ship's coordinates (longitude/latitude) as detected by AIS. Using such information, we can then build an early warning system (EWS) relayed through short message service (SMS), email, or other means when the ship enters the restricted and exclusion zone of platforms and pipelines. The ship inspection system is developed by combining several attributes. Then, decision analysis software is employed to prioritize the vessel's four attributes, including ship age, ship type, classification, and flag state. Results show that the EWS can increase the safety level of offshore platforms and pipelines, as well as the efficient use of patrol boats in monitoring the safety of the facilities. Meanwhile, ship inspection enables the port to prioritize the ship to be inspected in accordance with the priority ranking inspection score.

Review of technology for Arctic offshore oil and gas recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sackinger, W. M.

1980-08-01

The technical background briefing report is the first step in the preparation of a plan for engineering research oriented toward Arctic offshore oil and gas recovery. A five-year leasing schedule for the ice-prone waters of the Arctic offshore is presented, which also shows the projected dates of the lease sale for each area. The estimated peak production rates for these areas are given. There is considerable uncertainty for all these production estimates, since no exploratory drilling has yet taken place. A flow chart is presented which relates the special Arctic factors, such as ice and permafrost, to the normal petroleummore » production sequence. Some highlights from the chart and from the technical review are: (1) in many Arctic offshore locations the movement of sea ice causes major lateral forces on offshore structures, which are much greater than wave forces; (2) spray ice buildup on structures, ships and aircraft will be considerable, and must be prevented or accommodated with special designs; (3) the time available for summer exploratory drilling, and for deployment of permanent production structures, is limited by the return of the pack ice. This time may be extended by ice-breaking vessels in some cases; (4) during production, icebreaking workboats will service the offshore platforms in most areas throughout the year; (5) transportation of petroleum by icebreaking tankers from offshore tanker loading points is a highly probable situation, except in the Alaskan Beaufort; and (6) Arctic pipelines must contend with permafrost, making instrumentation necessary to detect subtle changes of the pipe before rupture occurs.« less

Development of a Semi-submersible Barge for the installation of a TLP floating substructure. TLPWIND® case study

NASA Astrophysics Data System (ADS)

Amate, Juan; Sánchez, Gustavo D.; González, Gonzalo

2016-09-01

One of the biggest challenges to introduce Tension Leg Platform (TLP) technology into the Offshore Wind market are the Transport & Installation (T&I) stages, since most of TLPs are not self-stable as semisubmersible or SPAR platforms, and consequently requires additional means to perform these operations. This paper addresses this problem that has been overcome through the development of a Semi-submersible “Transport & Installation” Barge (SSB) for Iberdrola's TLPWIND® floating support structure. The Semi-submersible Barge has been designed both through the use of numerical models and an extensive basin testing campaign carried out at the University of Strathclyde facilities. This paper also includes an estimation of the duration in time to carry out the installation process of a Floating Offshore Wind Farm, comprising 100x5MW TLPWIND® units in different scenarios.

Sediment porewater toxicity assessment studies in the vicinity of offshore oil and gas production platforms in the Gulf of Mexico

USGS Publications Warehouse

Carr, R.S.; Chapman, D.C.; Presley, B.J.; Biedenbach, J.M.; Robertson, L.; Boothe, P.; Kilada, R.; Wade, T.; Montagna, P.

1996-01-01

As part of a multidisciplinary program to assess the potential long-term impacts of offshore oil and gas exploration and production activities in the Gulf of Mexico, sediment chemical analyses and porewater toxicity tests were conducted in the vicinity of five offshore platforms. Based on data from sea urchin fertilization and embryological development assays, toxicity was observed near four of the five platforms sampled; the majority of the toxic samples were collected within 150 m of a platform. There was excellent agreement among the results of porewater tests with three different species (sea urchin embryological development, polychaete reproduction, and copepod nauplii survival). The sediment concentrations of several metals were well in excess of sediment quality assessment guidelines at a number of stations, and good agreement was observed between predicted and observed toxicity. Porewater metal concentrations compared with EC50, LOEC, and NOEC values generated for water-only exposures indicated that the porewater concentrations for several metals were high enough to account for the observed toxicity. Results of these studies utilizing highly sensitive toxicity tests suggest that the contaminant-induced impacts from offshore platforms are limited to a localized area in the immediate vicinity of the platforms. 

Nighttime approaches to offshore installations in Brazil: Safety shortcomings experienced by helicopter pilots.

PubMed

Nascimento, Felipe A C; Majumdar, Arnab; Jarvis, Steve

2012-07-01

Accident rates for night sorties by helicopters traveling to offshore oil and gas platforms are at least five times higher than those during the daytime. Because pilots need to transition from automated flight to a manually flown night visual segment during arrival, the approach and landing phases cause great concern. Despite this, in Brazil, regulatory changes have been sought to allow for the execution of offshore night flights because of the rapid expansion of the petroleum industry. This study explores the factors that affect safety during night visual segments in Brazil using 28 semi-structured interviews with offshore helicopter pilots, followed by a template analysis of the narratives. The relationships among the factors suggest that flawed safety oversights, caused by a combination of lack of infrastructure for night flights offshore and declining training, currently favor spatial disorientation on the approach and near misses when close to the destination. Safety initiatives can be derived on the basis of these results. Copyright © 2012 Elsevier Ltd. All rights reserved.

Portable life support for instrumentation of an offshore platform

NASA Technical Reports Server (NTRS)

Mull, M. M.; Coffin, C. L.

1972-01-01

A compressor was used to supply air through a nylon hose to the offshore platform field engineer working at the bottom of the piling. Air quality in the pile was sampled periodically for carbon dioxide, carbon monoxide, hydrogen sulfide, and combustible gases by an universal tester and an explosion meter.

Assessing Fatigue and Ultimate Load Uncertainty in Floating Offshore Wind Turbines Due to Varying Simulation Length

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stewart, G.; Lackner, M.; Haid, L.

2013-07-01

With the push towards siting wind turbines farther offshore due to higher wind quality and less visibility, floating offshore wind turbines, which can be located in deep water, are becoming an economically attractive option. The International Electrotechnical Commission's (IEC) 61400-3 design standard covers fixed-bottom offshore wind turbines, but there are a number of new research questions that need to be answered to modify these standards so that they are applicable to floating wind turbines. One issue is the appropriate simulation length needed for floating turbines. This paper will discuss the results from a study assessing the impact of simulation lengthmore » on the ultimate and fatigue loads of the structure, and will address uncertainties associated with changing the simulation length for the analyzed floating platform. Recommendations of required simulation length based on load uncertainty will be made and compared to current simulation length requirements.« less

Made in Norway -- Produsert i Norge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lia, A.

1996-08-01

This paper reviews the technology advances that have occurred as a result of the harsh offshore conditions and rigid environmental conditions that the Norwegian offshore has created. Over 25 years of offshore oil and gas production on the Norwegian continental shelf have given an impressive number of technological innovations. It includes the submerged turret loading system, concrete gravity based platforms, and the use of various platform configurations for protection against icebergs. This paper reviews the history of these and other Norwegian based technologies.

Fire Protection Jacket

NASA Technical Reports Server (NTRS)

1991-01-01

NERAC, Inc., Tolland, CT, aided Paul Monroe Engineering, Orange, CA, in the development of their PC1200 Series Fire Protection Jacket that protects the oil conduit system on an offshore drilling platform from the intense hydrocarbon fires that cause buckling and could cause structural failure of the platform. The flame-proof jacketing, which can withstand temperatures of 2000 degrees Fahrenheit for four hours or more, was developed from a combination of ceramic cloth (similar to the ceramic in Space Shuttle tiles), and laminates used in space suits.

A study of rotor and platform design trade-offs for large-scale floating vertical axis wind turbines

NASA Astrophysics Data System (ADS)

Griffith, D. Todd; Paquette, Joshua; Barone, Matthew; Goupee, Andrew J.; Fowler, Matthew J.; Bull, Diana; Owens, Brian

2016-09-01

Vertical axis wind turbines are receiving significant attention for offshore siting. In general, offshore wind offers proximity to large populations centers, a vast & more consistent wind resource, and a scale-up opportunity, to name a few beneficial characteristics. On the other hand, offshore wind suffers from high levelized cost of energy (LCOE) and in particular high balance of system (BoS) costs owing to accessibility challenges and limited project experience. To address these challenges associated with offshore wind, Sandia National Laboratories is researching large-scale (MW class) offshore floating vertical axis wind turbines (VAWTs). The motivation for this work is that floating VAWTs are a potential transformative technology solution to reduce offshore wind LCOE in deep-water locations. This paper explores performance and cost trade-offs within the design space for floating VAWTs between the configurations for the rotor and platform.

Geological history of the west Libyan offshore and adjoining regions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benniran, M.M.; Taleb, T.M.; McCrossan, R.G.

1988-08-01

The continental margin of the African plate north of Libya is separated from the Saharan platform to the south by a major Variscan fault system running along the coastline. The structural evolution of three sedimentary basins within the margin is discussed. The Jeffara basin, onshore western Libya-southern Tunisia, formed as a right-lateral pull-part late in the Variscan event. When the strike-slip motion ceased in the Late Permian, the basin continued to subside thermally. The Sabratah (Tripolitanian) basin, offshore western Libya-southern Tunisia, and the Benghazi basin in the Sirte rise were both formed as left-lateral pull-aparts in the Late Triassic-Early Jurassic.more » From the Middle Jurassic to the present they have subsided thermally. Onshore the lower Mesozoic is characterized by continental and nearshore clastics, separated by an evaporite sequence of Late Triassic-Early Jurassic age. Offshore this sequence is thought to grade northward into open marine carbonates. Uplift along the edge of the Saharan platform during the Early Cretaceous sourced coarse clastics, which grade northward into a thick sequence of shallow-water carbonates. Throughout the Late Cretaceous and early Tertiary, high-energy carbonates were deposited around the flanks of the Sabratah basin, grading into deeper-water, fine-grained clastics and carbonates toward the center of the basin. The late Tertiary succession is dominated by clastics derived from the growing Tellian Atlas to the northwest. During the Mesozoic and Tertiary a thick sequence of carbonates was deposited on the Pelagian platform to the north of the Sabratah basin. Periodically the platform was exposed subaerially.« less

Re-assessment of offshore structures using the revised HSE fatigue guidance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stacey, A.; Sharp, J.V.

1995-12-31

The re-assessment of existing North Sea structures is an increasingly important issue as the age of platforms increases. Over 50 from a total of approximately 180 fixed installations in the UK sector are now over 15 years old. Fatigue damage has been the main reason for repairs to North Sea structures and the risk of this continues. The fatigue guidance of the Offshore Safety Division of the Health and Safety Executive (HSE) has recently been revised and published. Fundamental changes have been made to this guidance with several new recommendations including joint classification, basic design S-N curves for welded joints,more » the thickness effect, the effects of environment and the treatment of low and high stress ranges. To quantify the effects of the new guidance on the fatigue life assessment of offshore strictures, the HSE commissioned a study which included a deep water and a shallow water fixed steel structure and a twin-pontoon semi-submersible. These structures are typical of those operating in the North Sea. These were re-assessed with respect to fatigue lives and the results compared with predictions based on the 1990 guidance. The results and general conclusions are presented in this paper.« less

Storm wave buoy equipped with micromechanical inertial unit: Results of development and testing

NASA Astrophysics Data System (ADS)

Gryazin, D. G.; Staroselcev, L. P.; Belova, O. O.; Gleb, K. A.

2017-07-01

The article describes the results of developing a wave buoy to measure the statistical characteristics of waves and the characteristics of directional spectra of three-dimensional waves. The device is designed for long-term measurements lasting up to a season, which can help solve problems in forecasting waves and preventing emergencies from wave impact on offshore platforms, hydraulic structures, and other marine facilities. The measuring unit involves triads of micromechanical gyroscopes, accelerometers, and a three-component magnetometer. A description of the device, results of laboratory research of its characteristics, and bench and full-scale tests are offered. It is noted that to assess the performance characteristics, comparative tests of the Storm wave buoy were conducted with a standard string wave probe installed on an offshore platform. It is shown that the characteristics and capabilities of the wave buoy make it possible to oust foreign devices from the domestic market.

Floating Offshore WTG Integrated Load Analysis & Optimization Employing a Tuned Mass Damper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodriguez Tsouroukdissian, Arturo; Lackner, Matt; Cross-Whiter, John

2015-09-25

Floating offshore wind turbines (FOWTs) present complex design challenges due to the coupled dynamics of the platform motion, mooring system, and turbine control systems, in response to wind and wave loading. This can lead to higher extreme and fatigue loads than a comparable fixed bottom or onshore system. Previous research[1] has shown the potential to reduced extreme and fatigue loads on FOWT using tuned mass dampers (TMD) for structural control. This project aims to reduce maximum loads using passive TMDs located at the tower top during extreme storm events, when grid supplied power for other controls systems may not bemore » available. The Alstom Haliade 6MW wind turbine is modelled on the Glosten Pelastar tension-leg platform (TLP). The primary objectives of this project are to provide a preliminary assessment of the load reduction potential of passive TMDs on real wind turbine and TLP designs.« less

On the effects of basic platform design characteristics on floating offshore wind turbine control and their mitigation

NASA Astrophysics Data System (ADS)

Olondriz, Joannes; Elorza, Iker; Trojaola, Ignacio; Pujana, Aron; Landaluze, Joseba

2016-09-01

Semi-submersible floating offshore wind turbines present significant advantages over other designs in terms of cost, deployment, maintenance and site-independence. However, these advantages are achieved by shifting a part of the burden of stabilising the platform pitch and roll motions to the turbine control system. A study is presented here of the effects of basic platform dimensions on the performance of a standard pitch controller and the possible methods for mitigating said effects.

Regional Patterns in Invertebrate Assemblages on Offshore Oil Platforms Along the Pacific Outer Continental Shelf

NASA Astrophysics Data System (ADS)

Zaleski, S.; Page, H. M.; Miller, R. J.; Doheny, B.; Dugan, J. E.; Schroeder, D. M.

2016-02-01

Twenty-seven oil and gas platforms are arrayed offshore California from north of Point Conception south to San Pedro Bay (a coastline distance of >300 km). To test the hypothesis that variability in the structure of sessile invertebrate communities on the platforms is associated with regional differences in sea surface temperature, we sampled space-holding invertebrate taxa photographically on 23 platforms and compared the composition and cover of invertebrates among and within regions using multivariate analyses. To explore temporal variability in invertebrate assemblages, we also compared the cover and composition of invertebrates on a subset of platforms in the Santa Barbara Channel (SBC) where data were collected over ten years previously. The composition of invertebrate assemblages differed significantly among regions, and was driven by variation in the relative abundance of certain anemone, bryozoan, tubiferous annelid, sponge, and bivalve taxa. The presence of non-native bryozoan and anemone taxa on some platforms in the south (San Pedro Bay) and southeast SBC contributed to the distinction of these assemblages from the others. Comparison of survey data on the subset of platforms in the SBC surveyed over ten years apart revealed little change in the cover of major space-holding taxa (e.g., anemones Metridium, Corynactis) across platforms, although there was an increase in cover of the non-native bryozoan Watersipora subtorquata between surveys. The existence of geographical patterns in the composition of platform invertebrate assemblages suggests that these assemblages may be useful as barometers of short and longer-term environmental change. For biogeographic transition zones, such as the SBC, monitoring of platform invertebrate assemblages could permit an evaluation of the concept that these zones are particularly susceptible to shifts in the composition of marine species driven by ocean climate.

[Relationship of job stress with job burnout and quality of work life in workers for offshore oil platforms].

PubMed

Zhang, Y; Liu, X L; Wei, T D; Lan, Y J

2017-03-20

Objective: To evaluate the current status of job burnout and qual ity of work life (QWL) in workers for offshore oil platforms, and to analyze the relationship of job stress with job burnout and QWL and the direct and indirect effects of job stress on QWL. Methods: Cluster random sampling was used to select 382 work-ers for 8 oil platforms of China National Offshore Oil Corporation in October 2015. A self - designed questionnaire was used to collect the individual characteristics of subjects. The Quality of Work Life Scale (QWL7 - 32) , Occupa-tional Stress Inventory - Revised Edition (OSI - R) , and Maslach Burnout Inventory - General Survey (MBI - GS) were used to investigate the QWL, job stress, and job burnout of subjects. Results: Among all the workers for offshore oil platforms, 87.2% had mild job burnout. The total QWL score was 116.01 ± 16.73; 8.3% of the workers had poor QWL, and 68.5% had moderate QWL. QWL was reduced with heavier task, vaguer task, and increasing mental stress and physical stress ( P <0.05) , and increased with more social support ( P <0.05) . Job stress had di-rect and indirect effects on QWL; stress reaction had the most effect on QWL (total effect size - 0.509) , followed by social support (total effect size 0.444) . Conclusion: Most workers for offshore oil platforms have mild job burn-out and moderate QWL. Job stress is associated with job burnout and QWL, and stress reaction and social support have relatively high influence on QWL.

Rarefaction Shock Wave Cutter for Offshore Oil-Gas Platform Removal Final Report CRADA No. TC02009.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glenn, L. A.; Barker, J.

This was a collaborative effort between Lawrence Livermore National Security, LLC/Lawrence Livermore National Laboratory (LLNL) (formerly the University of California) and Jet Research Center, a wholly owned division of Halliburton Energy Services, Inc. to design and prototype an improved explosive cutter for cutting the support legs of offshore oil and gas platforms.

Go to work or report sick? A focus group study on decisions of sickness presence among offshore catering section workers

PubMed Central

2011-01-01

Background To identify and explore the factors promoting sickness presenteeism among offshore catering section workers. Methods Twenty men and women, working in the offshore catering section onboard three offshore oil and gas production platforms on the Norwegian Continental Shelf, participated in three focus groups. Data from the focus groups were analysed according to a phenomenological approach, and supported by theories on presenteeism. Results The results show that the decision to attend work despite illness, first and foremost, was based on the severity of the health complaint. Other factors identified were; the individual's location once the health complaint occurred, job satisfaction, the norms of the team, and experiences of how company policies on sickness absenteeism were implemented by the catering section leaders. Conclusions Offshore working conditions may promote sickness presenteeism. The factors promoting sickness presenteeism onboard the platforms reflected experiences of a healthy work environment. PMID:21418561

Go to work or report sick? A focus group study on decisions of sickness presence among offshore catering section workers.

PubMed

Krohne, Kariann; Magnussen, Liv Heide

2011-03-18

To identify and explore the factors promoting sickness presenteeism among offshore catering section workers. Twenty men and women, working in the offshore catering section onboard three offshore oil and gas production platforms on the Norwegian Continental Shelf, participated in three focus groups. Data from the focus groups were analysed according to a phenomenological approach, and supported by theories on presenteeism. The results show that the decision to attend work despite illness, first and foremost, was based on the severity of the health complaint. Other factors identified were; the individual's location once the health complaint occurred, job satisfaction, the norms of the team, and experiences of how company policies on sickness absenteeism were implemented by the catering section leaders. Offshore working conditions may promote sickness presenteeism. The factors promoting sickness presenteeism onboard the platforms reflected experiences of a healthy work environment.

Assessing the suitability of a remotely operated vehicle (ROV) to study the fish community associated with offshore gas platforms in the Ionian Sea: a comparative analysis with underwater visual censuses (UVCs)

NASA Astrophysics Data System (ADS)

Andaloro, Franco; Ferraro, Maria; Mostarda, Edoardo; Romeo, Teresa; Consoli, Pierpaolo

2013-06-01

The effectiveness of a remotely operated vehicle (ROV) to describe the fish communities of three gas platforms located offshore Crotone (Italy, Ionian Sea) was investigated by comparing its observations with underwater visual censuses (UVCs). The study was carried out at two depth layers (0-6 and 12-18 m). Moreover, the ROV was used to survey three deeper depth layers up to 76 m. Overall, the ROV surveys failed to give a truthful representation of the fish communities underestimating the number of species and their abundances as compared to UVCs. The main discrepancies in data regarded crypto-benthic and nekto-benthic species, whereas the ROV proved to be a suitable method to census low-mobile and abundant planktivorous species. The differences between the fish assemblage described by the ROV, with respect to the one depicted by UVC, should be considered in the light of the technical limits of the recording camera, whose resolution and field of vision is clearly lower than the diver's eye. In addition, video images did not allow for the acquisition of a correct estimate of the distance between the individuals and the platform structures. This led, almost certainly, to an under- or over-estimation of fish abundance as regards to the censused volume. In spite of this, as a result of its capacity to reach depths inaccessible to scuba divers and then to add complementary information, the ROV could be used jointly with UVCs, in studies having as their objective the description of the fish communities associated with offshore platforms.

Mobile Landing Platform with Core Capability Set (MLP w/CCS): Combined Initial Operational Test and Evaluation and Live Fire Test and Evaluation Report

DTIC Science & Technology

2015-07-01

annex.   iii Self-defense testing was limited to structural test firing from each machine gun mount and an ammunition resupply drill. Robust self...provided in the classified annex. Self-   8 defense testing was limited to structural test firing from each machine gun mount and a single...Caliber Machine Gun Mount Structural Test Fire November 2014 San Diego, Offshore Ship Weapons Range Operating Independently       9 Section Three

Holocene evolution of coastal chalk cliffs in Normandy (NW France) as evidenced by onshore-offshore high resolution geomorphology

NASA Astrophysics Data System (ADS)

Duguet, Timothée; Duperret, Anne; Costa, Stéphane; Regard, Vincent; Maillet, Grégoire

2017-04-01

Key words: erosion, rocky coast, cliffs, shore platform, watersheds, cosmogenic dating The chalk cliffs coastline extends to 120 km long in Normandy. It suffers from high erosion rates with a mean of about 0.15 m/y. The shore platforms extending from the cliff base to the sea, keep structural marks of the cliff erosion during long periods, i.e. the Holocene. Therefore it is essential to take an active interest in their morphology and their evolution to better understand cliff erosion timing. A land-sea Digital Elevation Model (DEM) has been produced for Mesnil-Val and Criel-sur-Mer sites (Seine Maritime), with the merge of topographic data (RGE alti, IGN) and shallow bathymetric data from three oceanographic Cruises, CROCOLIT-1 and 3 (Duperret, 2013) and SPLASHALIOT-2 (Maillet, 2014). Valleys that have more or less incised Turonian-Coniacian chalk cliffs occupy the landward part of study sites. The N130E V-shaped incised Mesnil-Val dry valley is elevated at 29 m high above the shore platform level, whereas the N175E Criel-sur-Mer flat valley, extending on 700 m wide and occupied by the Yères river, is directly connected to the shore platform. Offshore, the shore platform morphology varies from Criel-sur-Mer (North) to Mesnil-Val (South). Northern part of the study site is characterized by 1 km wide shore platform made of an overlay of flat steps controlled by normal faults. Southern part highlights a shore platform with a seaward edge located at about 500 m from the cliff face and strictly parallel oriented to the present-day coastline over a minimum distance of 5 km, without fracture control. The shore platform seaward edge is more or less steep and is always localized below the limit of the lowest tide level. Its origin could be related to the in-depth waves influence or to a past sea level stagnation. We aim to identify the origin of this seaward edge, using cosmogenic 10Be dating in order to develop a chalky shore platform evolution model. It is necessary to take into account detailed rock lithology and rock resistance, large and small-scale structural deformation and fractures occurrences versus the sea level variations during the Holocene. A numeric watersheds analysis has been performed inland to highlight the morphometric properties and the maturity status of each quaternary valley. They appear to be immature, even if their downstream areas demonstrate slopes varying between 0.5 and 2°. Paleo-rivers stopped to incise the chalk before reaching their equilibrium level base. We thus consider that the equilibrium point where the paleo-rivers and the past sea level were connected is located on the shore platform i.e. today located offshore. Therefore we project offshore the V-shaped valley base level, using Hack's law to estimate the paleo-coastline location. It will be correlated to the sea level fluctuations from the last interglacial period and to the Holocene shoreline recession rates known from the 10Be cosmogenic dating. References DUPERRET Anne (2013) CROCOLIT_LEG1 cruise, RV Haliotis, http://dx.doi.org/10.17600/13120080 DUPERRET Anne (2013) CROCOLIT_LEG3 cruise, RV Haliotis, http://dx.doi.org/10.17600/13120100 MAILLET Grégoire (2014) SPLASHALIOT-2 cruise, RV Haliotis, http://dx.doi.org/10.17600/14011800

Inadequate environmental monitoring around offshore oil and gas platforms on the Grand Bank of Eastern Canada: are risks to marine birds known?

PubMed

Burke, C M; Montevecchi, W A; Wiese, F K

2012-08-15

Petroleum exploration and production on the Grand Bank of eastern Canada overlaps with productive marine habitat that supports over 40 million marine birds annually. Environmental assessments for oil and gas projects in the region predict insignificant adverse effects on marine birds from oil spills, incineration in platform flares and collisions. Limited baseline data on seasonal occupancies and a failure to quantify the nature and extent of marine bird attraction to platforms and related mortality undermines these assessments. We conducted 22 surveys to offshore platforms on the Grand Bank during 1999-2003 to measure avian associations with platforms and to determine the level of monitoring needed to assess the risks to marine birds. We document seasonal shifts in marine bird occurrences and higher densities of auks (fall) and shearwaters (summer) around platforms relative to surrounding areas. The limited temporal and spatial coverage of our surveys is more robust than existing industry monitoring efforts, yet it is still inadequate to quantify the scale of marine bird associations with platforms or their associated mortality risks. Systematic observations by independent biologists on vessels and platforms are needed to generate reliable assessments of risks to marine birds. Instead, the regulatory body for offshore oil and gas in eastern Canada (Canada - Newfoundland and Labrador Offshore Petroleum Board; C-NLOPB) supports industry self-reporting as the accepted form of environmental monitoring. Conflicting responsibilities of oil and gas regulatory agencies for both energy development and environmental monitoring are major barriers to transparency, unbiased scientific inquiry and adequate environmental protection. Similar conflicts with the oil and gas regulatory body in the United States, the former Minerals and Management Service (MMS) were identified by the U.S. President as a major contributor to the Deepwater Horizon disaster in the Gulf of Mexico. The MMS has since been restructured into the Bureau of Ocean Energy Management, (BOEM) with separate departments responsible for drilling leases and the regulation of drilling activities. Similar restructuring of the oil and gas regulatory bodies in Canada is needed for better public information, scientific investigation and environmental protection in the offshore. Copyright © 2012 Elsevier Ltd. All rights reserved.

The SPOT Project (Potentially Triggerable Offshore Seismicity and Tsunamis): a First Appraisal of the Possible Impact of Oil and Gas Platforms on the Seismic and Tsunami Risks along the Italian Coasts

NASA Astrophysics Data System (ADS)

Basili, R.; Di Bucci, D.; Antoncecchi, I.; Ciccone, F.; Teofilo, G.; Argnani, A.; Rovere, M.; Ligi, M.; Coltelli, M.; Lorito, S.; Borzi, B.; Germagnoli, F.; Di Ludovico, M.; Lignola, G. P.; Prota, A.

2017-12-01

The majority of oil and gas production in Europe takes place offshore and Italy is one of the European countries with the longest coastlines facing these operations. Given the generally growing energy demand, and the increasing concern toward human-driven hazards, scientists are called to provide background information for helping ensure a safe energy supply. We here present the activities of the project SPOT, which is aimed to help Italian authorities comply with the application of the Safety of Offshore Oil and Gas Operations European Directive (2013/30/EU) and the ensuing Italian codes. We carry out a reconstruction of offshore geological structures to assess the existence of potentially seismogenic faults in the surroundings of off-shore platforms. This study is a propaedeutic step for the assessment of potentially triggered seismicity connected with operations on such platforms. The descriptive parameters (3D geometry and behavior) of the identified faults will be used to estimate their natural earthquake rates. The impact of these natural earthquakes along the coasts will then be modeled in terms of expected ground shaking and tsunamis. The tsunamis potentially generated by submarine landslides induced by earthquake shaking will also be analyzed. In turn, these models will be used to estimate potential human and economic losses in a multi-hazard approach to risk assessment. Wherever the combined earthquake and tsunami modeling indicates a relevant impact along the coasts, a more detailed analysis will be carried out, also involving the operators of the related platforms, to perform specific models which also take into account production and/or storage data. Activities with a consolidated background, such as those concerning the impact scenarios of earthquakes, and more innovative activities, such as those dedicated to build up the first vulnerability/fragility curves related to tsunamis for the Italian building stock, will be integrated within the project. The details of the project workflow, along with the preliminary results of the first leg of activities will be presented. The SPOT project has been conceived and funded by the Italian Ministry of Economic Development, with the technical support of the National Department of Civil Protection, following auspices of the Italian Major Risk Commission.

Association of sea turtles with petroleum platforms in the north-central Gulf of Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lohoefener, R.; Hoggard, W.; Mullin, K.

1990-06-01

There are over 4,500 petroleum platforms in the north-central Gulf of Mexico. Explosives are commonly used to remove platforms and have the potential to kill nearby sea turtles. From June 1988-June 1990, the authors used aerial surveys to study turtle density and the spatial relationship between turtles and platforms offshore of Louisiana. They sighted 316 turtles most of which (92%) were loggerheads. Seventy-eight percent were sighted just east of the Mississippi River offshore of the Chandeleur Islands. East of the river, turtle densities ranged from 0.92 (winter) to 4.83 turtles/100 sq km (spring). West of the river, annual densities rangedmore » from 0.11-0.50 turtles/100 sq km. East of the river, three statistical tests indicated that turtles were generally closer to platforms than expected by chance alone. West of the river, turtles were randomly located with respect to platform locations. Before explosives are used, current mitigation measures require that no turtle can be sighted within 1,000 m of the platform. East of the river, the probability of a turtle being within 1,000 m of any platform selected at random was about 60%; west of the river, 2-7%. West of the river to about 92 W, the mitigation measures should protect turtles but offshore of the Chandeleur Islands, special precautions should be taken.« less

Bird interactions with offshore oil and gas platforms: review of impacts and monitoring techniques.

PubMed

Ronconi, Robert A; Allard, Karel A; Taylor, Philip D

2015-01-01

Thousands of oil and gas platforms are currently operating in offshore waters globally, and this industry is expected to expand in coming decades. Although the potential environmental impacts of offshore oil and gas activities are widely recognized, there is limited understanding of their impacts on migratory and resident birds. A literature review identified 24 studies and reports of bird-platform interactions, most being qualitative and half having been peer-reviewed. The most frequently observed effect, for seabirds and landbirds, is attraction and sometimes collisions associated with lights and flares; episodic events have caused the deaths of hundreds or even thousands of birds. Though typically unpredictable, anecdotally, it is known that poor weather, such as fog, precipitation and low cloud cover, can exacerbate the effect of nocturnal attraction to lights, especially when coincidental with bird migrations. Other effects include provision of foraging and roosting opportunities, increased exposure to oil and hazardous environments, increased exposure to predators, or repulsion from feeding sites. Current approaches to monitoring birds at offshore platforms have focused on observer-based methods which can offer species-level bird identification, quantify seasonal patterns of relative abundance and distribution, and document avian mortality events and underlying factors. Observer-based monitoring is time-intensive, limited in spatial and temporal coverage, and suffers without clear protocols and when not conducted by trained, independent observers. These difficulties are exacerbated because deleterious bird-platform interaction is episodic and likely requires the coincidence of multiple factors (e.g., darkness, cloud, fog, rain conditions, occurrence of birds in vicinity). Collectively, these considerations suggest a need to implement supplemental systems for monitoring bird activities around offshore platforms. Instrument-based approaches, such as radar, cameras, acoustic recordings, and telemetry, hold promise for continuous monitoring. Recommendations are provided for a rigorous and comprehensive monitoring approach within an adaptive management framework. Copyright © 2014 Elsevier Ltd. All rights reserved.

A Delay Vector Variance based Marker for an Output-Only Assessment of Structural Changes in Tension Leg Platforms

NASA Astrophysics Data System (ADS)

Jaksic, V.; Wright, C.; Mandic, D. P.; Murphy, J.; Pakrashi, V.

2015-07-01

Although aspects of power generation of many offshore renewable devices are well understood, their dynamic responses under high wind and wave conditions are still to be investigated to a great detail. Output only statistical markers are important for these offshore devices, since access to the device is limited and information about the exposure conditions and the true behaviour of the devices are generally partial, limited, and vague or even absent. The markers can summarise and characterise the behaviour of these devices from their dynamic response available as time series data. The behaviour may be linear or nonlinear and consequently a marker that can track the changes in structural situations can be quite important. These markers can then be helpful in assessing the current condition of the structure and can indicate possible intervention, monitoring or assessment. This paper considers a Delay Vector Variance based marker for changes in a tension leg platform tested in an ocean wave basin for structural changes brought about by single column dampers. The approach is based on dynamic outputs of the device alone and is based on the estimation of the nonlinearity of the output signal. The advantages of the selected marker and its response with changing structural properties are discussed. The marker is observed to be important for monitoring the as- deployed structural condition and is sensitive to changes in such conditions. Influence of exposure conditions of wave loading is also discussed in this study based only on experimental data.

Offshore platform sourced pollution monitoring using space-borne fully polarimetric C and X band synthetic aperture radar.

PubMed

Singha, Suman; Ressel, Rudolf

2016-11-15

Use of polarimetric SAR data for offshore pollution monitoring is relatively new and shows great potential for operational offshore platform monitoring. This paper describes the development of an automated oil spill detection chain for operational purposes based on C-band (RADARSAT-2) and X-band (TerraSAR-X) fully polarimetric images, wherein we use polarimetric features to characterize oil spills and look-alikes. Numbers of near coincident TerraSAR-X and RADARSAT-2 images have been acquired over offshore platforms. Ten polarimetric feature parameters were extracted from different types of oil and 'look-alike' spots and divided into training and validation dataset. Extracted features were then used to develop a pixel based Artificial Neural Network classifier. Mutual information contents among extracted features were assessed and feature parameters were ranked according to their ability to discriminate between oil spill and look-alike spots. Polarimetric features such as Scattering Diversity, Surface Scattering Fraction and Span proved to be most suitable for operational services. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pioneering offshore excellence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kent, R.P.; Grattan, L.

1996-11-01

Hibernia Management and Development Company Ltd. (HMDC) was formed in 1990 by a consortium of oil companies to develop their interests in the Hibernia and Avalon reservoirs offshore Newfoundland in a safe and environmentally responsible manner. The reservoirs are located 315km ESE of St. John`s in the North Atlantic. The water depth is about 80m. The entire Hibernia field is estimated to contain more than three billion barrels of oil in place and the owners development plan area is estimated to contain two billion barrels. Recoverable reserves are estimated to be approximately 615 million barrels. The Hibernia reservoir, the principlemore » reservoir, is located at an average depth of 3,700m. HMDC is building a large concrete gravity based structure (GBS) that which will support the platform drilling and processing facilities and living quarters for 280 personnel. In 1997 the platform will be towed to the production site and production will commence late 1997. Oil will be exported by a 2 km long pipeline to an offshore loading system. Dynamically positioned tankers will then take the oil to market. Average daily production is expected to plateau between 125,000 and 135,000 BOPD. It will be the first major development on the east coast of Canada and is located in an area that is prone to pack ice and icebergs.« less

OTEC Cold Water Pipe-Platform Subsystem Dynamic Interaction Validation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Varley, Robert; Halkyard, John; Johnson, Peter

A commercial floating 100-megawatt (MW) ocean thermal energy conversion (OTEC) power plant will require a cold water pipe (CWP) with a diameter of 10-meter (m) and length of up to 1,000 m. The mass of the cold water pipe, including entrained water, can exceed the mass of the platform supporting it. The offshore industry uses software-modeling tools to develop platform and riser (pipe) designs to survive the offshore environment. These tools are typically validated by scale model tests in facilities able to replicate real at-sea meteorological and ocean (metocean) conditions to provide the understanding and confidence to proceed to finalmore » design and full-scale fabrication. However, today’s offshore platforms (similar to and usually larger than those needed for OTEC applications) incorporate risers (or pipes) with diameters well under one meter. Secondly, the preferred construction method for large diameter OTEC CWPs is the use of composite materials, primarily a form of fiber-reinforced plastic (FRP). The use of these material results in relatively low pipe stiffness and large strains compared to steel construction. These factors suggest the need for further validation of offshore industry software tools. The purpose of this project was to validate the ability to model numerically the dynamic interaction between a large cold water-filled fiberglass pipe and a floating OTEC platform excited by metocean weather conditions using measurements from a scale model tested in an ocean basin test facility.« less

A new submarine oil-water separation system

NASA Astrophysics Data System (ADS)

Cai, Wen-Bin; Liu, Bo-Hong

2017-12-01

In order to solve the oil field losses of environmental problems and economic benefit caused by the separation of lifting production liquid to offshore platforms in the current offshore oil production, from the most basic separation principle, a new oil-water separation system has been processed of adsorption and desorption on related materials, achieving high efficiency and separation of oil and water phases. And the submarine oil-water separation device has been designed. The main structure of the device consists of gas-solid phase separation device, period separating device and adsorption device that completed high efficiency separation of oil, gas and water under the adsorption and desorption principle, and the processing capacity of the device is calculated.

Using coral disease prevalence to assess the effects of concentrating tourism activities on offshore reefs in a tropical marine park.

PubMed

Lamb, Joleah B; Willis, Bette L

2011-10-01

Concentrating tourism activities can be an effective way to closely manage high-use parks and minimize the extent of the effects of visitors on plants and animals, although considerable investment in permanent tourism facilities may be required. On coral reefs, a variety of human-related disturbances have been associated with elevated levels of coral disease, but the effects of reef-based tourist facilities (e.g., permanent offshore visitor platforms) on coral health have not been assessed. In partnership with reef managers and the tourism industry, we tested the effectiveness of concentrating tourism activities as a strategy for managing tourism on coral reefs. We compared prevalence of brown band disease, white syndromes, black band disease, skeletal eroding band, and growth anomalies among reefs with and without permanent tourism platforms within the Great Barrier Reef Marine Park. Coral diseases were 15 times more prevalent at reefs with offshore tourism platforms than at nearby reefs without platforms. The maximum prevalence and maximum number of cases of each disease type were recorded at reefs with permanently moored tourism platforms. Diseases affected 10 coral genera from 7 families at reefs with platforms and 4 coral genera from 3 families at reefs without platforms. The greatest number of disease cases occurred within the spatially dominant acroporid corals, which exhibited 18-fold greater disease prevalence at reefs with platforms than at reefs without platforms. Neither the percent cover of acroporids nor overall coral cover differed significantly between reefs with and without platforms, which suggests that neither factor was responsible for the elevated levels of disease. Identifying how tourism activities and platforms facilitate coral disease in marine parks will help ensure ongoing conservation of coral assemblages and tourism. ©2011 Society for Conservation Biology.

Computationally inexpensive approach for pitch control of offshore wind turbine on barge floating platform.

PubMed

Zuo, Shan; Song, Y D; Wang, Lei; Song, Qing-wang

2013-01-01

Offshore floating wind turbine (OFWT) has gained increasing attention during the past decade because of the offshore high-quality wind power and complex load environment. The control system is a tradeoff between power tracking and fatigue load reduction in the above-rated wind speed area. In allusion to the external disturbances and uncertain system parameters of OFWT due to the proximity to load centers and strong wave coupling, this paper proposes a computationally inexpensive robust adaptive control approach with memory-based compensation for blade pitch control. The method is tested and compared with a baseline controller and a conventional individual blade pitch controller with the "NREL offshore 5 MW baseline wind turbine" being mounted on a barge platform run on FAST and Matlab/Simulink, operating in the above-rated condition. It is shown that the advanced control approach is not only robust to complex wind and wave disturbances but adaptive to varying and uncertain system parameters as well. The simulation results demonstrate that the proposed method performs better in reducing power fluctuations, fatigue loads and platform vibration as compared to the conventional individual blade pitch control.

Computationally Inexpensive Approach for Pitch Control of Offshore Wind Turbine on Barge Floating Platform

PubMed Central

Zuo, Shan; Song, Y. D.; Wang, Lei; Song, Qing-wang

2013-01-01

Offshore floating wind turbine (OFWT) has gained increasing attention during the past decade because of the offshore high-quality wind power and complex load environment. The control system is a tradeoff between power tracking and fatigue load reduction in the above-rated wind speed area. In allusion to the external disturbances and uncertain system parameters of OFWT due to the proximity to load centers and strong wave coupling, this paper proposes a computationally inexpensive robust adaptive control approach with memory-based compensation for blade pitch control. The method is tested and compared with a baseline controller and a conventional individual blade pitch controller with the “NREL offshore 5 MW baseline wind turbine” being mounted on a barge platform run on FAST and Matlab/Simulink, operating in the above-rated condition. It is shown that the advanced control approach is not only robust to complex wind and wave disturbances but adaptive to varying and uncertain system parameters as well. The simulation results demonstrate that the proposed method performs better in reducing power fluctuations, fatigue loads and platform vibration as compared to the conventional individual blade pitch control. PMID:24453834

Development of pile foundation bias factors using observed behavior of platforms during Hurricane Andrew

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aggarwal, R.K.; Litton, R.W.; Cornell, C.A.

1996-12-31

The performance of more than 3,000 offshore platforms in the Gulf of Mexico was observed during the passage of Hurricane Andrew in August 1992. This event provided an opportunity to test the procedures used for platform analysis and design. A global bias was inferred for overall platform capacity and loads in the Andrew Joint Industry Project (JIP) Phase 1. It was predicted that the pile foundations of several platforms should have failed, but did not. These results indicated that the biases specific to foundation failure modes may be higher than those of jacket failure modes. The biases in predictions ofmore » foundation failure modes were therefore investigated further in this study. The work included capacity analysis and calibration of predictions with the observed behavior for 3 jacket platforms and 3 caissons using Bayesian updating. Bias factors for two foundation failure modes, lateral shear and overturning, were determined for each structure. Foundation capacity estimates using conventional methods were found to be conservatively biased overall.« less

Underwater Nondestructive Testing of Ship Hull Welds

DTIC Science & Technology

1979-09-01

Norske Veritas. 5. Alan Taylor , Underwater Testing, Marine rechnology (Germany) Dec 1971, pp. 251-2. 6. Ship Underwater Maintenance, Evaluation and Repair...11. Peters, V. "NDT for Offshore Drilling Platform Structure," Welding end Metal Fabricatior, Jul 1973, V. 41-7. 12. Taylor , A., "Underwater...N. Cordea, Chairman, Senior Staff MetalZlugiet, ARMCO INC., Middletown, OH Mr. W. C. Brayton , Aset. to Gener•l Manager, Bethlehem Steel Corp

Screening of biosurfactant-producing bacteria from offshore oil and gas platforms in North Atlantic Canada.

PubMed

Cai, Qinhong; Zhang, Baiyu; Chen, Bing; Song, Xing; Zhu, Zhiwen; Cao, Tong

2015-05-01

From offshore oil and gas platforms in North Atlantic Canada, crude oil, formation water, drilling mud, treated produced water and seawater samples were collected for screening potential biosurfactant producers. In total, 59 biosurfactant producers belong to 4 genera, namely, Bacillus, Rhodococcus, Halomonas, and Pseudomonas were identified and characterized. Phytogenetic trees based on 16S ribosomal deoxyribonucleic acid (16S rDNA) were constructed with isolated strains plus their closely related strains and isolated strains with biosurfactant producers in the literature, respectively. The distributions of the isolates were site and medium specific. The richness, diversity, and evenness of biosurfactant producer communities in oil and gas platform samples have been analyzed. Diverse isolates were found with featured properties such as effective reduction of surface tension, producing biosurfactants at high rate and stabilization of water-in-oil or oil-in-water emulsion. The producers and their corresponding biosurfactants had promising potential in applications such as offshore oil spill control, enhancing oil recovery and soil washing treatment of petroleum hydrocarbon-contaminated sites.

H∞ memory feedback control with input limitation minimization for offshore jacket platform stabilization

NASA Astrophysics Data System (ADS)

Yang, Jia Sheng

2018-06-01

In this paper, we investigate a H∞ memory controller with input limitation minimization (HMCIM) for offshore jacket platforms stabilization. The main objective of this study is to reduce the control consumption as well as protect the actuator when satisfying the requirement of the system performance. First, we introduce a dynamic model of offshore platform with low order main modes based on mode reduction method in numerical analysis. Then, based on H∞ control theory and matrix inequality techniques, we develop a novel H∞ memory controller with input limitation. Furthermore, a non-convex optimization model to minimize input energy consumption is proposed. Since it is difficult to solve this non-convex optimization model by optimization algorithm, we use a relaxation method with matrix operations to transform this non-convex optimization model to be a convex optimization model. Thus, it could be solved by a standard convex optimization solver in MATLAB or CPLEX. Finally, several numerical examples are given to validate the proposed models and methods.

[Relationship between occupational stress and mental health in offshore oil platform workers].

PubMed

Wu, Hongtao; Xiao, Taiqin; Zou, Jianfang; Shan, Yongle; Li, Zijian

2014-02-01

To investigate the relationship between occupational stress and mental health in offshore oil platform workers and to provide a scientific basis for protection of their mental health. A total of 768 workers on offshore oil platform were surveyed with the Occupational Stress Inventory Revised Edition and Symptom Check List-90 (SCL-90). The total score of Occupational Role Questionnaire (ORQ) for the workers (160.27±24.63) was significantly lower than the national norm (166.52±27.01) (P < 0.01); the total score of Personal Strain Questionnaire (PSQ) (101.96±19.8) was significantly higher than the national norm (92.45±17.33) (P < 0.01). The total score of Personal Resource Questionnaire (PRQ) for the workers was not significantly different from the national norm (P > 0.05), but the items of recreation, social support, and rational/cognitive found significant difference (P < 0.05). The total score of SCL-90 was positively correlated with all items of ORQ and PSQ (P < 0.01) and negatively correlated with all items of PRQ (P < 0.01). The multiple stepwise regression analysis showed that current work seniority, education background, drinking, role overload, role insufficiency, role ambiguity, responsibility, physical environment, and rational/cognitive conduct impacted the score of SCL-90 (P < 0.05). The mental health of workers on offshore oil platform is related to occupational stress, and role overload, role ambiguity, physical environment, and rational/cognitive conduct, etc, are closely associated with the workers' mental health.

Environmental Impact of Offshore Gas Activities on the Benthic Environment: A Case Study

NASA Astrophysics Data System (ADS)

Punzo, E.; Gomiero, A.; Tassetti, A. N.; Strafella, P.; Santelli, A.; Salvalaggio, V.; Spagnolo, A.; Scarcella, G.; De Biasi, A. M.; Kozinkova, L.; Fabi, G.

2017-08-01

Multidisciplinary monitoring of the impact of offshore gas platforms on northern and central Adriatic marine ecosystems has been conducted since 1998. Beginning in 2006, 4-5 year investigations spanning the period before, during, and after rig installation have explored the effects of its construction and presence on macrozoobenthic communities, sediment, water quality, pollutant bioaccumulation, and fish assemblages. In this study, sediment samples collected at increasing distance from an offshore gas platform before, during and after its construction were subjected to chemical analysis and assessment of benthic communities. Ecological indices were calculated to evaluate the ecological status of the area. Ecotoxicological analysis of sediment was performed to establish whether pollutants are transferred to biota. The study applied a before-after control-impact design to assess the effects of rig construction and presence and provide reference data on the possible impacts of any further expansion of the gas extraction industry in the already heavily exploited Adriatic Sea. Only some of the metals investigated (barium, chromium, cadmium, and zinc) showed a different spatial and/or temporal distribution that may be platform-related. In the early phases, the sediment concentrations of polycyclic aromatic hydrocarbons were below the detection limit at all sites; they then became detectable, but without significant spatial differences. The present findings suggest that the environmental effects of offshore gas platforms may be difficult to quantify, interpret, and generalize, because they are influenced by numerous, often local, abiotic, and biotic variables in different and unpredictable ways.

Environmental Impact of Offshore Gas Activities on the Benthic Environment: A Case Study.

PubMed

Punzo, E; Gomiero, A; Tassetti, A N; Strafella, P; Santelli, A; Salvalaggio, V; Spagnolo, A; Scarcella, G; De Biasi, A M; Kozinkova, L; Fabi, G

2017-08-01

Multidisciplinary monitoring of the impact of offshore gas platforms on northern and central Adriatic marine ecosystems has been conducted since 1998. Beginning in 2006, 4-5 year investigations spanning the period before, during, and after rig installation have explored the effects of its construction and presence on macrozoobenthic communities, sediment, water quality, pollutant bioaccumulation, and fish assemblages. In this study, sediment samples collected at increasing distance from an offshore gas platform before, during and after its construction were subjected to chemical analysis and assessment of benthic communities. Ecological indices were calculated to evaluate the ecological status of the area. Ecotoxicological analysis of sediment was performed to establish whether pollutants are transferred to biota. The study applied a before-after control-impact design to assess the effects of rig construction and presence and provide reference data on the possible impacts of any further expansion of the gas extraction industry in the already heavily exploited Adriatic Sea. Only some of the metals investigated (barium, chromium, cadmium, and zinc) showed a different spatial and/or temporal distribution that may be platform-related. In the early phases, the sediment concentrations of polycyclic aromatic hydrocarbons were below the detection limit at all sites; they then became detectable, but without significant spatial differences. The present findings suggest that the environmental effects of offshore gas platforms may be difficult to quantify, interpret, and generalize, because they are influenced by numerous, often local, abiotic, and biotic variables in different and unpredictable ways.

Atmospheric metallic and arsenic pollution at an offshore drilling platform in the Bo Sea: A health risk assessment for the workers.

PubMed

Xu, Hong; Han, Suqin; Bi, Xiaohui; Zhao, Zhijing; Zhang, Lei; Yang, Wenjie; Zhang, Min; Chen, Jing; Wu, Jianhui; Zhang, Yufen; Feng, Yinchang

2016-03-05

To investigate the ambient metal pollution at the offshore drilling platform in the Bo Sea, which few studies have focused on, PM2.5 samples were collected and ten heavy metals, as well as As, were analyzed. High concentration levels of metals were observed, and the heavy metal pollution was quite serious compared to air quality standards and other marine areas. Back trajectories and wind dependent and PCA analyses showed that the marine sources included ship traffic emissions and corrosive stainless steels from the equipment at the platform as well as industrial emissions from stainless steel production and coal combustion sources, which were transported from the surrounding mainland. Both contributed greatly to the ambient metallic particles at the offshore platform. The Hazard Index values of the metals, which were much less than 1, the Carcinogenic Risk data, which were lower than the EPA's acceptable range, and the fact that the metal concentrations did not the exceed the permissible exposure limits of OSHA, indicated that the health risks from the ambient metallic particles for the oil-drilling workers were not significant. Copyright © 2015 Elsevier B.V. All rights reserved.

Development of structural health monitoring techniques using dynamics testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

James, G.H. III

Today`s society depends upon many structures (such as aircraft, bridges, wind turbines, offshore platforms, buildings, and nuclear weapons) which are nearing the end of their design lifetime. Since these structures cannot be economically replaced, techniques for structural health monitoring must be developed and implemented. Modal and structural dynamics measurements hold promise for the global non-destructive inspection of a variety of structures since surface measurements of a vibrating structure can provide information about the health of the internal members without costly (or impossible) dismantling of the structure. In order to develop structural health monitoring for application to operational structures, developments inmore » four areas have been undertaken within this project: operational evaluation, diagnostic measurements, information condensation, and damage identification. The developments in each of these four aspects of structural health monitoring have been exercised on a broad range of experimental data. This experimental data has been extracted from structures from several application areas which include aging aircraft, wind energy, aging bridges, offshore structures, structural supports, and mechanical parts. As a result of these advances, Sandia National Laboratories is in a position to perform further advanced development, operational implementation, and technical consulting for a broad class of the nation`s aging infrastructure problems.« less

Research on the influence of helical strakes on dynamic response of floating wind turbine platform

NASA Astrophysics Data System (ADS)

Ding, Qin-wei; Li, Chun

2017-04-01

The stability of platform structure is the paramount guarantee of the safe operation of the offshore floating wind turbine. The NREL 5MW floating wind turbine is established based on the OC3-Hywind Spar Buoy platform with the supplement of helical strakes for the purpose to analyze the impact of helical strakes on the dynamic response of the floating wind turbine Spar platform. The dynamic response of floating wind turbine Spar platform under wind, wave and current loading from the impact of number, height and pitch ratio of the helical strakes is analysed by the radiation and diffraction theory, the finite element method and orthogonal design method. The result reveals that the helical strakes can effectively inhibit the dynamic response of the platform but enlarge the wave exciting force; the best parameter combination is two pieces of helical strakes with the height of 15% D ( D is the diameter of the platform) and the pitch ratio of 5; the height of the helical strake and its pitch ratio have significant influence on pitch response.

Offshore marine constructions as propagators of moon jellyfish dispersal

NASA Astrophysics Data System (ADS)

Vodopivec, Martin; Peliz, Álvaro J.; Malej, Alenka

2017-08-01

We have studied the influence of offshore marine constructions on the moon jellyfish population in the Adriatic sea, where the newly set up substrates enable the formation of a new population based in the formerly unpopulated open waters. Our five-year long computer simulation uses a high resolution coupled bio-physical individual-based model to track the dispersal of the offspring from subpopulations originating from offshore and shore-based sources. According to our study, the platforms enhance connectivity between subpopulations of jellyfish polyps, help sustain existing shore-based subpopulations, contribute to jellyfish blooms in some areas, and play an important role in establishing connection with the rest of the Mediterranean, in addition to representing substantial amounts of available substrate. This is an aspect that is usually overlooked when evaluating the ecological impact of existing and future wind farms, oil and gas platforms, etc. Our approach could serve as a role model in future studies of ecological impacts of planned offshore constructions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The first controlled-temperature ice plug in the bend of an offshore gas trunkline has been carried out for Phillips Petroleum Co. Norway on its Norpipe A.S. platform in the German sector of the North Sea. The procedure was part of a subsea valve repair operation. The ice plug was successfully formed offshore and tested to a differential pressure of 1,450 psi. Repair of two valves required only 5 days during which time gas production was operating at close to 50--60% via the platform bypass, says the service company. The paper discusses the procedure.

Stabilized floating platforms

DOEpatents

Thomas, David G.

1976-01-01

The subject invention is directed to a floating platform for supporting nuclear reactors and the like at selected offshore sites. The platform is provided with a stabilizer mechanism which significantly reduces the effects of wave action upon the platform and which comprises a pair of relatively small floats attached by rigid booms to the platform at locations spaced therefrom for reducing wave pitch, acceleration, and the resonance period of the wave.

Design features of offshore oil production platforms influence their susceptibility to biocorrosion.

PubMed

Duncan, Kathleen E; Davidova, Irene A; Nunn, Heather S; Stamps, Blake W; Stevenson, Bradley S; Souquet, Pierre J; Suflita, Joseph M

2017-08-01

Offshore oil-producing platforms are designed for efficient and cost-effective separation of oil from water. However, design features and operating practices may create conditions that promote the proliferation and spread of biocorrosive microorganisms. The microbial communities and their potential for metal corrosion were characterized for three oil production platforms that varied in their oil-water separation processes, fluid recycling practices, and history of microbially influenced corrosion (MIC). Microbial diversity was evaluated by 16S rRNA gene sequencing, and numbers of total bacteria, archaea, and sulfate-reducing bacteria (SRB) were estimated by qPCR. The rates of 35 S sulfate reduction assay (SRA) were measured as a proxy for metal biocorrosion potential. A variety of microorganisms common to oil production facilities were found, but distinct communities were associated with the design of the platform and varied with different locations in the processing stream. Stagnant, lower temperature (<37 °C) sites in all platforms had more SRB and higher SRA compared to samples from sites with higher temperatures and flow rates. However, high (5 mmol L -1 ) levels of hydrogen sulfide and high numbers (10 7  mL -1 ) of SRB were found in only one platform. This platform alone contained large separation tanks with long retention times and recycled fluids from stagnant sites to the beginning of the oil separation train, thus promoting distribution of biocorrosive microorganisms. These findings tell us that tracking microbial sulfate-reducing activity and community composition on off-shore oil production platforms can be used to identify operational practices that inadvertently promote the proliferation, distribution, and activity of biocorrosive microorganisms.

Offshore Wind Turbines - Estimated Noise from Offshore Wind Turbine, Monhegan Island, Maine: Environmental Effects of Offshore Wind Energy Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aker, Pamela M.; Jones, Anthony M.; Copping, Andrea E.

2010-11-23

Deep C Wind, a consortium headed by the University of Maine will test the first U.S. offshore wind platforms in 2012. In advance of final siting and permitting of the test turbines off Monhegan Island, residents of the island off Maine require reassurance that the noise levels from the test turbines will not disturb them. Pacific Northwest National Laboratory, at the request of the University of Maine, and with the support of the U.S. Department of Energy Wind Program, modeled the acoustic output of the planned test turbines.

Study and Test of a New Bundle-Structure Riser Stress Monitoring Sensor Based on FBG.

PubMed

Xu, Jian; Yang, Dexing; Qin, Chuan; Jiang, Yajun; Sheng, Leixiang; Jia, Xiangyun; Bai, Yang; Shen, Xiaohong; Wang, Haiyan; Deng, Xin; Xu, Liangbin; Jiang, Shiquan

2015-11-24

To meet the requirements of riser safety monitoring in offshore oil fields, a new Fiber Bragg Grating (FBG)-based bundle-structure riser stress monitoring sensor has been developed. In cooperation with many departments, a 49-day marine test in water depths of 1365 m and 1252 m was completed on the "HYSY-981" ocean oil drilling platform. No welding and pasting were used when the sensor was installed on risers. Therefore, the installation is convenient, reliable and harmless to risers. The continuous, reasonable, time-consistent data obtained indicates that the sensor worked normally under water. In all detailed working conditions, the test results show that the sensor can do well in reflecting stresses and bending moments both in and in magnitude. The measured maximum stress is 132.7 MPa, which is below the allowable stress. In drilling and testing conditions, the average riser stress was 86.6 MPa, which is within the range of the China National Offshore Oil Corporation (CNOOC) mechanical simulation results.

Study and Test of a New Bundle-Structure Riser Stress Monitoring Sensor Based on FBG

PubMed Central

Xu, Jian; Yang, Dexing; Qin, Chuan; Jiang, Yajun; Sheng, Leixiang; Jia, Xiangyun; Bai, Yang; Shen, Xiaohong; Wang, Haiyan; Deng, Xin; Xu, Liangbin; Jiang, Shiquan

2015-01-01

To meet the requirements of riser safety monitoring in offshore oil fields, a new Fiber Bragg Grating (FBG)-based bundle-structure riser stress monitoring sensor has been developed. In cooperation with many departments, a 49-day marine test in water depths of 1365 m and 1252 m was completed on the “HYSY-981” ocean oil drilling platform. No welding and pasting were used when the sensor was installed on risers. Therefore, the installation is convenient, reliable and harmless to risers. The continuous, reasonable, time-consistent data obtained indicates that the sensor worked normally under water. In all detailed working conditions, the test results show that the sensor can do well in reflecting stresses and bending moments both in and in magnitude. The measured maximum stress is 132.7 MPa, which is below the allowable stress. In drilling and testing conditions, the average riser stress was 86.6 MPa, which is within the range of the China National Offshore Oil Corporation (CNOOC) mechanical simulation results. PMID:26610517

30 CFR 250.911 - If my platform is subject to the Platform Verification Program, what must I do?

Code of Federal Regulations, 2011 CFR

2011-07-01

... installation for the Regional Supervisor's approval. You must include a project management timeline, Gantt... MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR...

Turboexpanders with pressurized magnetic bearings for off-shore applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agahi, R.R.; Ershaghi, B.; Baudelocque, L.

1995-12-31

There are two primary parameters that encourage the use of magnetic bearings in turbomachinery: oil-free process and space requirements. For cryogenic processes such as hydrogen purification and ethylene plants, oil free process is the primary objective. In the case of off-shore platforms for oil and gas production, the occupied space and weight are of prime concern. In off-shore operations, the process gas density is usually higher than in normal process plants because the gas is untreated and at high pressure. High density process gas generates more windage loss and may also cause excessive radial load to journal bearings. The bearingmore » assembly design should be suitable for sour gas environments as well. Furthermore, the thrust bearing system should withstand process fluctuations which are more severe due to high pressure. In this paper, the authors explain their experience of designing a turboexpander-compressor with magnetic bearings for an off-shore oil production platform. They will present side load analysis and their solutions for heat dissipation and coping with process fluctuations.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, F.J.

As the petroleum industry has moved into deeper and deeper water for the recovery of oil and gas, weight-sensitive floating platforms have replaced stationary, bottom-founded structures. The cost penalty for weight or vertical tension supported by floaters such as tension leg platforms (TLPs) is in the range of $10--20/kg. Hence, there is considerable incentive to reduce the weight of equipment or structural members on these platforms and downward forces exerted on these platforms by production and export risers, and mooring lines. Thus, there are numerous opportunities for utilizing light-weight, high-strength composites. The offshore petroleum industry has acknowledged the desirable performancemore » characteristics of composites for some time but only recently has there been some optimism that composites could be cost-effective. For most, if not all perceived applications, advanced composites are not considered to be technically enabling for current water depths of interest, i.e., 600--1,200m. However, in a very real sense, they may be economically enabling. In particular, they may allow marginal prospects to be developed or may expedite field development subject to capital constraints. The paper discusses composite production risers, break-even costs and savings, and riser tensioners.« less

Dynamics modeling and loads analysis of an offshore floating wind turbine

NASA Astrophysics Data System (ADS)

Jonkman, Jason Mark

The vast deepwater wind resource represents a potential to use offshore floating wind turbines to power much of the world with renewable energy. Many floating wind turbine concepts have been proposed, but dynamics models, which account for the wind inflow, aerodynamics, elasticity, and controls of the wind turbine, along with the incident waves, sea current, hydrodynamics, and platform and mooring dynamics of the floater, were needed to determine their technical and economic feasibility. This work presents the development of a comprehensive simulation tool for modeling the coupled dynamic response of offshore floating wind turbines, the verification of the simulation tool through model-to-model comparisons, and the application of the simulation tool to an integrated loads analysis for one of the promising system concepts. A fully coupled aero-hydro-servo-elastic simulation tool was developed with enough sophistication to address the limitations of previous frequency- and time-domain studies and to have the features required to perform loads analyses for a variety of wind turbine, support platform, and mooring system configurations. The simulation capability was tested using model-to-model comparisons. The favorable results of all of the verification exercises provided confidence to perform more thorough analyses. The simulation tool was then applied in a preliminary loads analysis of a wind turbine supported by a barge with catenary moorings. A barge platform was chosen because of its simplicity in design, fabrication, and installation. The loads analysis aimed to characterize the dynamic response and to identify potential loads and instabilities resulting from the dynamic couplings between the turbine and the floating barge in the presence of combined wind and wave excitation. The coupling between the wind turbine response and the barge-pitch motion, in particular, produced larger extreme loads in the floating turbine than experienced by an equivalent land-based turbine. Instabilities were also found in the system. The influence of conventional wind turbine blade-pitch control actions on the pitch damping of the floating turbine was also assessed. Design modifications for reducing the platform motions, improving the turbine response, and eliminating the instabilities are suggested. These suggestions are aimed at obtaining cost-effective designs that achieve favorable performance while maintaining structural integrity.

Integration of offshore wind farms through high voltage direct current networks

NASA Astrophysics Data System (ADS)

Livermore, Luke

The integration of offshore wind farms through Multi Terminal DC (MTDC) networks into the GB network was investigated. The ability of Voltage Source Converter (VSC) High Voltage Direct Current (HVDC) to damp Subsynchronous Resonance (SSR) and ride through onshore AC faults was studied. Due to increased levels of wind generation in Scotland, substantial onshore and offshore reinforcements to the GB transmission network are proposed. Possible inland reinforcements include the use of series compensation through fixed capacitors. This potentially can lead to SSR. Offshore reinforcements are proposed by two HVDC links. In addition to its primary functions of bulk power transmission, a HVDC link can be used to provide damping against SSR, and this function has been modelled. Simulation studies have been carried out in PSCAD. In addition, a real-time hardware-in-the-loop HVDC test rig has been used to implement and validate the proposed damping scheme on an experimental platform. When faults occur within AC onshore networks, offshore MTDC networks are vulnerable to DC overvoltages, potentially damaging the DC plant and cables. Power reduction and power dissipation control systems were investigated to ride through onshore AC faults. These methods do not require dedicated fast communication systems. Simulations and laboratory experiments are carried out to evaluate the control systems, with the results from the two platforms compared..

Explosives remain preferred methods for platform abandonment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pulsipher, A.; Daniel, W. IV; Kiesler, J.E.

1996-05-06

Economics and safety concerns indicate that methods involving explosives remain the most practical and cost-effective means for abandoning oil and gas structures in the Gulf of Mexico. A decade has passed since 51 dead sea turtles, many endangered Kemp`s Ridleys, washed ashore on the Texas coast shortly after explosives helped remove several offshore platforms. Although no relationship between the explosions and the dead turtles was ever established, in response to widespread public concern, the US Minerals Management Service (MMS) and National Marine Fisheries Service (NMFS) implemented regulations limiting the size and timing of explosive charges. Also, more importantly, they requiredmore » that operators pay for observers to survey waters surrounding platforms scheduled for removal for 48 hr before any detonations. If observers spot sea turtles or marine mammals within the danger zone, the platform abandonment is delayed until the turtles leave or are removed. However, concern about the effects of explosives on marine life remains.« less

Comparison of Hydrodynamic Load Predictions Between Engineering Models and Computational Fluid Dynamics for the OC4-DeepCwind Semi-Submersible: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benitz, M. A.; Schmidt, D. P.; Lackner, M. A.

Hydrodynamic loads on the platforms of floating offshore wind turbines are often predicted with computer-aided engineering tools that employ Morison's equation and/or potential-flow theory. This work compares results from one such tool, FAST, NREL's wind turbine computer-aided engineering tool, and the computational fluid dynamics package, OpenFOAM, for the OC4-DeepCwind semi-submersible analyzed in the International Energy Agency Wind Task 30 project. Load predictions from HydroDyn, the offshore hydrodynamics module of FAST, are compared with high-fidelity results from OpenFOAM. HydroDyn uses a combination of Morison's equations and potential flow to predict the hydrodynamic forces on the structure. The implications of the assumptionsmore » in HydroDyn are evaluated based on this code-to-code comparison.« less

Characteristics of produced water discharged to the Gulf of Mexico hypoxiczone.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Veil, J. A.; Kimmell, T. A.; Rechner, A. C.

2005-08-24

Each summer, an area of low dissolved oxygen (the hypoxic zone) forms in the shallow nearshore Gulf of Mexico waters from the Mississippi River Delta westward to near the Texas/Louisiana border. Most scientists believe that the leading contributor to the hypoxic zone is input of nutrients (primarily nitrogen and phosphorus compounds) from the Mississippi and Atchafalaya Rivers. The nutrients stimulate growth of phytoplankton. As the phytoplankton subsequently die, they fall to the bottom waters where they are decomposed by microorganisms. The decomposition process consumes oxygen in the bottom waters to create hypoxic conditions. Sources other than the two rivers mentionedmore » above may also contribute significant quantities of oxygen-demanding pollutants. One very visible potential source is the hundreds of offshore oil and gas platforms located within or near the hypoxic zone. Many of these platforms discharge varying volumes of produced water. However, only limited data characterizing oxygen demand and nutrient concentration and loading from offshore produced water discharges have been collected. No comprehensive and coordinated oxygen demand data exist for produced water discharges in the Gulf of Mexico. This report describes the results of a program to sample 50 offshore oil and gas platforms located within the Gulf of Mexico hypoxic zone. The program was conducted in response to a requirement in the U.S. Environmental Protection Agency (EPA) general National Pollutant Discharge Elimination System (NPDES) permit for offshore oil and gas discharges. EPA requested information on the amount of oxygen-demanding substances contained in the produced water discharges. This information is needed as inputs to several water quality models that EPA intends to run to estimate the relative contributions of the produced water discharges to the occurrence of the hypoxic zone. Sixteen platforms were sampled 3 times each at approximately one-month intervals to give an estimate of temporal variability. An additional 34 platforms were sampled one time. The 50 sampled platforms were scattered throughout the hypoxic zone to give an estimate of spatial variability. Each platform was sampled for biochemical oxygen demand (BOD), total organic carbon (TOC), nitrogen (ammonia, nitrate, nitrite, and total Kjeldahl nitrogen [TKN]), and phosphorus (total phosphorus and orthophosphate). In addition to these parameters, each sample was monitored for pH, conductivity, salinity, and temperature. The sampling provided average platform concentrations for each parameter. Table ES-1 shows the mean, median, maximum, and minimum for the sampled parameters. For some of the parameters, the mean is considerably larger than the median, suggesting that one or a few data points are much higher than the rest of the points (outliers). Chapter 4 contains an extensive discussion of outliers and shows how the sample results change if outliers are deleted from consideration. A primary goal of this study is to estimate the mass loading (lb/day) of each of the oxygen-demanding pollutants from the 50 platforms sampled in the study. Loading is calculated by multiplying concentrations by the discharge volume and then by a conversion factor to allow units to match. The loadings calculated in this study of 50 platforms represent a produced water discharge volume of about 176,000 bbl/day. The total amount of produced water generated in the hypoxic zone during the year 2003 was estimated as 508,000 bbl/day. This volume is based on reports by operators to the Minerals Management Service each year. It reflects the volume of produced water that is generated from each lease, not the volume that is discharged from each platform. The mass loadings from offshore oil and gas discharges to the entire hypoxic zone were estimated by multiplying the 50-platform loadings by the ratio of total water generated to 50-platform discharge volume. The loadings estimated for the 50 platforms and for the entire hypoxic zone are shown in Table ES-2. These estimates and the sampling data from 50 platforms represent the most complete and comprehensive effort ever undertaken to characterize the amount and potential sources of the oxygen demand in offshore oil and gas produced water discharges.« less

Weathering the Storm: Developing a Spatial Data Infrastructure and Online Research Platform for Oil Spill Preparedness

NASA Astrophysics Data System (ADS)

Bauer, J. R.; Rose, K.; Romeo, L.; Barkhurst, A.; Nelson, J.; Duran-Sesin, R.; Vielma, J.

2016-12-01

Efforts to prepare for and reduce the risk of hazards, from both natural and anthropogenic sources, which threaten our oceans and coasts requires an understanding of the dynamics and interactions between the physical, ecological, and socio-economic systems. Understanding these coupled dynamics are essential as offshore oil & gas exploration and production continues to push into harsher, more extreme environments where risks and uncertainty increase. However, working with these large, complex data from various sources and scales to assess risks and potential impacts associated with offshore energy exploration and production poses several challenges to research. In order to address these challenges, an integrated assessment model (IAM) was developed at the Department of Energy's (DOE) National Energy Technology Laboratory (NETL) that combines spatial data infrastructure and an online research platform to manage, process, analyze, and share these large, multidimensional datasets, research products, and the tools and models used to evaluate risk and reduce uncertainty for the entire offshore system, from the subsurface, through the water column, to coastal ecosystems and communities. Here, we will discuss the spatial data infrastructure and online research platform, NETL's Energy Data eXchange (EDX), that underpin the offshore IAM, providing information on how the framework combines multidimensional spatial data and spatio-temporal tools to evaluate risks to the complex matrix of potential environmental, social, and economic impacts stemming from modeled offshore hazard scenarios, such as oil spills or hurricanes. In addition, we will discuss the online analytics, tools, and visualization methods integrated into this framework that support availability and access to data, as well as allow for the rapid analysis and effective communication of analytical results to aid a range of decision-making needs.

Petroleum production structures: economic resources for Louisiana sport divers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, K.J.; Thompson, M.E.

1983-08-01

The era of expanding petroleum production from marine waters began 12 miles off the Louisiana coast in 1947 with a joint operation. Since then, the expansion of drilling and production operations has continued until, in 1981, approximately 3,500 structures were located in the Gulf of Mexico. Of the total number of structures, federal and state waters off Louisiana contain 3,100. Scientific articles dealing with the role of structures in marine habitat and their relationship to sport fishing in the Gulf of Mexico increased over the decade. This newly publicized beneficial aspect of structures is particularly important to the marine fisherymore » off Louisiana. The structures (to which Dugas et al. attribute 'nearly all of the offshore sport fishery') are called as platforms in their description: These platforms are supported by a prewelded framework of steel pipe. Structures in other areas of the country also attract marine life and sport fishermen. Catch rates by sport fishermen were two to three times higher near structures off California than near natural reefs. (Turner et al. 1969). This may be the result of the 'fish-concentrating' nature of structures.« less

The Role of Faulting on the Growth of a Carbonate Platform: Evidence from 3D Seismic Analysis and Section Restoration

NASA Astrophysics Data System (ADS)

Nur Fathiyah Jamaludin, Siti; Pubellier, Manuel; Prasad Ghosh, Deva; Menier, David; Pierson, Bernard

2014-05-01

Tectonics in addition to other environmental factors impacts the growth of carbonate platforms and plays an important role in shaping the internal architecture of the platforms. Detailed of faults and fractures development and healing in carbonate environment have not been explored sufficiently. Using 3D seismic and well data, we attempt to reconstruct the structural evolution of a Miocene carbonate platform in Central Luconia Province, offshore Malaysia. Luconia Province is located in the NW coast of Borneo and has become one of the largest carbonate factories in SE Asia. Seismic interpretations including seismic attribute analysis are applied to the carbonate platform to discern its sedimentology and structural details. Detailed seismic interpretations highlight the relationships of carbonate deposition with syn-depositional faulting. Branching conjugate faults are common in this carbonate platform and have become a template for reef growth, attesting lateral facies changes within the carbonate environments. Structural restoration was then appropriately performed on the interpreted seismic sections based on sequential restoration techniques, and provided images different from those of horizon flattening methods. This permits us to compensate faults' displacement, remove recent sediment layers and finally restore the older rock units prior to the fault motions. It allows prediction of platform evolution as a response to faulting before and after carbonate deposition and also enhances the pitfalls of interpretation. Once updated, the reconstructions allow unravelling of the un-seen geological features underneath the carbonate platform, such as paleo-structures and paleo-topography which in turn reflects the paleo-environment before deformations took place. Interestingly, sections balancing and restoration revealed the late-phase (Late Oligocene-Early Miocene) rifting of South China Sea, otherwise difficult to visualize on seismic sections. Later it is shown that this carbonate platform was possibly originated from two or more connected reef build-ups. The platform evolution in terms of tectonic influences on carbonate growth and development may serve as a case example for re-evaluation of pre-Late Miocene structures as a new potential target for hydrocarbon exploration in Central Luconia Province. Eventually, techniques used in this study might be of interest to oil and gas explorers in carbonate system.

Radionuclides, Metals, and Hydrocarbons in Oil and Gas Operational Discharges and Environmental Samples Associated with Offshore Production Facilities on the Texas/Louisiana Continental Shelf with an Environmental Assessment of Metals and Hydrocarbons.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-06-01

This report presents concentrations of radionuclides, metals, and hydrocarbons in samples of produced water and produced sand from oil and gas production platforms located offshore Texas and Louisiana. concentrations in produced water discharge plume / receiving water, ambient seawater, sediment, interstitial water, and marine animal tissue samples collected in the vicinity of discharging platforms and reference sites distant from discharges are also reported and discussed. An environmental risk assessment is made on the basis of the concentration of metals and hydrocarbons determined in the samples.

Radionuclides, Metals, and Hydrocarbons in Oil and Gas Operational Discharges and Environmental Samples Associated with Offshore Production Facilities on the Texas/Louisiana Continental Shelf with an Environmental Assessment of Metals and Hydrocarbons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Continental Shelf Associates, Inc.

1999-08-16

This report presents concentrations of radionuclides, metals, and hydrocarbons in samples of produced water and produced sand from oil and gas production platforms located offshore Texas and Louisiana. Concentrations in produced water discharge plume/receiving water, ambient seawater, sediment, interstitial water, and marine animal tissue samples collected in the vicinity of discharging platforms and reference sites distant from discharges are also reported and discussed. An environmental risk assessment is made on the basis of the concentrations of metals and hydrocarbons determined in the samples.

A simplified method in comparison with comprehensive interaction incremental dynamic analysis to assess seismic performance of jacket-type offshore platforms

NASA Astrophysics Data System (ADS)

Zolfaghari, M. R.; Ajamy, A.; Asgarian, B.

2015-12-01

The primary goal of seismic reassessment procedures in oil platform codes is to determine the reliability of a platform under extreme earthquake loading. Therefore, in this paper, a simplified method is proposed to assess seismic performance of existing jacket-type offshore platforms (JTOP) in regions ranging from near-elastic to global collapse. The simplified method curve exploits well agreement between static pushover (SPO) curve and the entire summarized interaction incremental dynamic analysis (CI-IDA) curve of the platform. Although the CI-IDA method offers better understanding and better modelling of the phenomenon, it is a time-consuming and challenging task. To overcome the challenges, the simplified procedure, a fast and accurate approach, is introduced based on SPO analysis. Then, an existing JTOP in the Persian Gulf is presented to illustrate the procedure, and finally a comparison is made between the simplified method and CI-IDA results. The simplified method is very informative and practical for current engineering purposes. It is able to predict seismic performance elasticity to global dynamic instability with reasonable accuracy and little computational effort.

High-resolution onshore-offshore morpho-bathymetric records of modern chalk and granitic shore platforms in NW France

NASA Astrophysics Data System (ADS)

Duperret, Anne; Raimbault, Céline; Le Gall, Bernard; Authemayou, Christine; van Vliet-Lanoë, Brigitte; Regard, Vincent; Dromelet, Elsa; Vandycke, Sara

2016-07-01

Modern shore platforms developed on rocky coasts are key areas for understanding coastal erosion processes during the Holocene. This contribution offers a detailed picture of two contrasted shore-platform systems, based on new high-resolution shallow-water bathymetry, further coupled with aerial LiDAR topography. Merged land-sea digital elevation models were achieved on two distinct types of rocky coasts along the eastern English Channel in France (Picardy and Upper-Normandy: PUN) and in a NE Atlantic area (SW Brittany: SWB) in NW France. About the PUN case, submarine steps, identified as paleo-shorelines, parallel the actual coastline. Coastal erosive processes appear to be continuous and regular through time, since mid-Holocene at least. In SWB, there is a discrepancy between contemporary coastline orientation and a continuous step extending from inland to offshore, identified as a paleo-shoreline. This illustrates a polyphased and inherited shore platform edification, mainly controlled by tectonic processes.

Review of potential impacts to sea turtles from underwater explosive removal of offshore structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Viada, Stephen T.; Hammer, Richard M.; Racca, Roberto

2008-05-15

The purpose of this study was to collect and synthesize existing information relevant to the explosive removal of offshore structures (EROS) in aquatic environments. Data sources were organized and summarized by topic - explosive removal methods, physics of underwater explosions, sea turtle resources, documented impacts to sea turtles, and mitigation of effects. Information was gathered via electronic database searches and literature source review. Bulk explosive charges are the most commonly used technique in EROS. While the physical principles of underwater detonations and the propagation of pressure and acoustic waves are well understood, there are significant gaps in the application ofmore » this knowledge. Impacts to sea turtles from explosive removal operations may range from non-injurious effects (e.g. acoustic annoyance; mild tactile detection or physical discomfort) to varying levels of injury (i.e. non-lethal and lethal injuries). Very little information exists regarding the impacts of underwater explosions on sea turtles. Effects of explosions on turtles often must be inferred from documented effects to other vertebrates with lungs or other gas-containing organs, such as mammals and most fishes. However, a cautious approach should be used when determining impacts to sea turtles based on extrapolations from other vertebrates. The discovery of beached sea turtles and bottlenose dolphins following an explosive platform removal event in 1986 prompted the initiation of formal consultation between the U.S. Department of the Interior, Minerals Management Service (MMS) and the National Marine Fisheries Service (NMFS), authorized through the Endangered Species Act Section 7, to determine a mechanism to minimize potential impacts to listed species. The initial consultation resulted in a requirement for oil and gas companies to obtain a permit (through separate consultations on a case-by-case basis) prior to using explosives in Federal waters. Because many offshore structure removal operations are similar, a 'generic' Incidental Take Statement was established by the NMFS that describes requirements to protect sea turtles when an operator's individual charge weights did not exceed 50 lb (23 kg). Requirements associated with the Incidental Take Permit were revised in 2003 and 2006 to accommodate advances in explosive charge technologies, removals of structures in deeper waters, and adequate protection of deep water marine mammal species in Gulf of Mexico waters. Generally, these requirements include pre- and post-detonation visual monitoring using standard surface and aerial survey methods for sea turtles and marine mammals, and, in some scenarios, passive acoustic survey methods for marine mammals within a specified radius from an offshore structure. The survey program has been successful in mitigating impacts to sea turtles associated with EROS. However, even with these protective measures in place, there have been observations of sea turtles affected by explosive platform removals.« less

Bacterial diversity in water injection systems of Brazilian offshore oil platforms.

PubMed

Korenblum, Elisa; Valoni, Erika; Penna, Mônica; Seldin, Lucy

2010-01-01

Biogenic souring and microbial-influenced corrosion is a common scenario in water-flooded petroleum reservoirs. Water injection systems are continuously treated to control bacterial contamination, but some bacteria that cause souring and corrosion can persist even after different treatments have been applied. Our aim was to increase our knowledge of the bacterial communities that persist in the water injection systems of three offshore oil platforms in Brazil. To achieve this goal, we used a culture-independent molecular approach (16S ribosomal RNA gene clone libraries) to analyze seawater samples that had been subjected to different treatments. Phylogenetic analyses revealed that the bacterial communities from the different platforms were taxonomically different. A predominance of bacterial clones affiliated with Gammaproteobacteria, mostly belonging to the genus Marinobacter (60.7%), were observed in the platform A samples. Clones from platform B were mainly related to the genera Colwellia (37.9%) and Achromobacter (24.6%), whereas clones obtained from platform C were all related to unclassified bacteria. Canonical correspondence analyses showed that different treatments such as chlorination, deoxygenation, and biocide addition did not significantly influence the bacterial diversity in the platforms studied. Our results demonstrated that the injection water used in secondary oil recovery procedures contained potentially hazardous bacteria, which may ultimately cause souring and corrosion.

Recent Niobium Developments for High Strength Steel Energy Applications

NASA Astrophysics Data System (ADS)

Jansto, Steven G.

Niobium-containing high strength steel materials have been developed for oil and gas pipelines, offshore platforms, nuclear plants, boilers and alternative energy applications. Recent research and the commercialization of alternative energy applications such as windtower structural supports and power transmission gear components provide enhanced performance. Through the application of these Nb-bearing steels in demanding energy-related applications, the designer and end user experience improved toughness at low temperature, excellent fatigue resistance and fracture toughness and excellent weldability. These enhancements provide structural engineers the opportunity to further improve the structural design and performance. For example, through the adoption of these Nb-containing structural materials, several design-manufacturing companies are initiating new windtower designs operating at higher energy efficiency, lower cost, and improved overall material design performance.

Data Modeling, Development, Installation and Operation of the ACEX Offshore Drilling Information System for the Mission Specific Platform Expedition to the Lomonosov Ridge, Arctic Ocean.

NASA Astrophysics Data System (ADS)

Conze, R.; Krysiak, F.; Wallrabe-Adams, H.; Graham, C. C.

2004-12-01

During August/September 2004, the Arctic Coring Expedition (ACEX) was used to trial a new Offshore Drilling Information System (OffshoreDIS). ACEX was the first Mission Specific Platform (MSP) expedition of the Integrated Ocean Drilling Programme (IODP), funded by the European Consortium for Ocean Research Drilling (ECORD). The British Geological Survey in conjunction with the University of Bremen and the European Petrophysics Consortium were the ECORD Science Operator (ESO) for ACEX. IODP MSP expeditions have very similar data management requirements and operate in similar working environments to the lake drilling projects conducted by the International Continental Scientific Drilling Program (ICDP), for example, the GLAD800, which has very restricted space on board and operates in difficult conditions. Both organizations require data capture and management systems that are mobile, flexible and that can be deployed quickly on small- to medium-sized drilling platforms for the initial gathering of data, and that can also be deployed onshore in laboratories where the bulk of the scientific work is conducted. ESO, therefore, decided that an adapted version of the existing Drilling Information System (DIS) used by ICDP projects would satisfy its requirements. Based on the existing DIS, an OffshoreDIS has been developed for MSP expeditions. The underlying data model is compatible with IODP(JANUS), the Bremen Core Repository, WDC-MARE/PANGAEA and the LacCore in Minneapolis. According to the specific expedition platform configuration and on-board workflow requirements for the Arctic, this data model, data pumps and user interfaces were adapted for the ACEX-OffshoreDIS. On the drill ship Vidar Viking the cores were catalogued and petrophysically logged using a GeoTek Multi-Sensor Core Logger System, while further initial measurements, lithological descriptions and biostratigraphic investigations were undertaken on the Oden, which provided laboratory facilities for the expedition. Onboard samples were registered in a corresponding sample archive on both vessels. The ACEX-OffshoreDIS used a local area network covering the two ships of the three icebreaker fleet by wireless LAN between the ships and partly wired LAN on the ships. A DIS-server was installed on each ship. These were synchronized by database replication and linked to a total of 10 client systems and label printers across both ships. The ACEX-OffshoreDIS will also be used for the scientific measurement and analysis phase of the expedition during the post-field operations `shore-party' in November 2004 at the Bremen Core Repository (BCR). The data management system employed in the Arctic will be reconfigured and deployed at the BCR. In addition, an eXtended DIS (XDIS) Web interface will be available. This will allow controlled sample distribution (core curation, sub-sampling) as well as sharing of data (registration, upload and download) with other laboratories which will be undertaking additional sampling and analyses. The OffshoreDIS data management system will be of long-term benefit to both IODP and ICDP, being deployed in forthcoming MSP offshore projects, ICDP lake projects and joint IODP-ICDP projects such as the New Jersey Coastal Plain Drilling Project.

26 CFR 1.638-1 - Continental Shelf areas.

Code of Federal Regulations, 2013 CFR

2013-04-01

... exploitation of oil and is physically present on an offshore oil drilling platform operated by employees of L... a foreign country, designs equipment for use on oil drilling platforms affixed to the continental... corporation, to engage in exploratory oil drilling activities on a leasehold held by Y Corporation. Such...

26 CFR 1.638-1 - Continental Shelf areas.

Code of Federal Regulations, 2014 CFR

2014-04-01

... exploitation of oil and is physically present on an offshore oil drilling platform operated by employees of L... a foreign country, designs equipment for use on oil drilling platforms affixed to the continental... corporation, to engage in exploratory oil drilling activities on a leasehold held by Y Corporation. Such...

26 CFR 1.638-1 - Continental Shelf areas.

Code of Federal Regulations, 2012 CFR

2012-04-01

... exploitation of oil and is physically present on an offshore oil drilling platform operated by employees of L... a foreign country, designs equipment for use on oil drilling platforms affixed to the continental... corporation, to engage in exploratory oil drilling activities on a leasehold held by Y Corporation. Such...

26 CFR 1.638-1 - Continental Shelf areas.

Code of Federal Regulations, 2011 CFR

2011-04-01

... exploitation of oil and is physically present on an offshore oil drilling platform operated by employees of L... a foreign country, designs equipment for use on oil drilling platforms affixed to the continental... corporation, to engage in exploratory oil drilling activities on a leasehold held by Y Corporation. Such...

Drill cuttings mount formation study

NASA Astrophysics Data System (ADS)

Teh, Su Yean; Koh, Hock Lye

2014-07-01

Oil, Gas and Energy sector has been identified as an essential driving force in the Malaysian Economic Transformation Programs (ETP). Recently confirmed discovery of many offshore oil and gas deposits in Malaysian waters has ignited new confidence in this sector. However, this has also spurred intense interest on safeguarding the health and environment of coastal waters in Malaysia from adverse impact resulting from offshore oil and gas production operation. Offshore discharge of spent drilling mud and rock cuttings is the least expensive and simplest option to dispose of large volumes of drilling wastes. But this onsite offshore disposal may have adverse environmental impacts on the water column and the seabed. It may also pose occupational health hazards to the workers living in the offshore platforms. It is therefore important to model the transport and deposition of drilling mud and rock cuttings in the sea to enable proper assessment of their adverse impacts on the environment and the workers. Further, accumulation of drill particles on the seabed may impede proper operation of pipelines on the seabed. In this paper, we present an in-house application model TUNA-PT developed to cater to local oil and gas industry needs to simulate the dispersion and mount formation of drill cuttings by offshore oil and gas exploration and production platforms. Using available data on Malaysian coastal waters, simulation analyses project a pile formation on the seabed with a maximum height of about 1 m and pile radius of around 30 to 50 m. Simulated pile heights are not sensitive to the heights of release of the cuttings as the sensitivity has been mitigated by the depth of water.

First evaluation of foraminiferal metabarcoding for monitoring environmental impact from an offshore oil drilling site.

PubMed

Laroche, Olivier; Wood, Susanna A; Tremblay, Louis A; Ellis, Joanne I; Lejzerowicz, Franck; Pawlowski, Jan; Lear, Gavin; Atalah, Javier; Pochon, Xavier

2016-09-01

At present, environmental impacts from offshore oil and gas activities are partly determined by measuring changes in macrofauna diversity. Morphological identification of macrofauna is time-consuming, expensive and dependent on taxonomic expertise. In this study, we evaluated the applicability of using foraminiferal-specific metabarcoding for routine monitoring. Sediment samples were collected along distance gradients from two oil platforms off Taranaki (New Zealand) and their physico-chemical properties, foraminiferal environmental DNA/RNA, and macrofaunal composition analyzed. Macrofaunal and foraminiferal assemblages showed similar shifts along impact gradients, but responded differently to environmental perturbations. Macrofauna were affected by hypoxia, whereas sediment grain size appeared to drive shifts in foraminifera. We identified eight foraminiferal molecular operational taxonomic units that have potential to be used as bioindicator taxa. Our results show that metabarcoding represents an effective tool for assessing foraminiferal communities near offshore oil and gas platforms, and that it can be used to complement current monitoring techniques. Copyright © 2016 Elsevier Ltd. All rights reserved.

Offshore Hydrokinetic Energy Conversion for Onshore Power Generation

NASA Technical Reports Server (NTRS)

Jones, Jack A.; Chao, Yi

2009-01-01

Design comparisons have been performed for a number of different tidal energy systems, including a fully submerged, horizontal-axis electro-turbine system, similar to Verdant Tidal Turbines in New York's East River, a platform-based Marine Current Turbine, now operating in Northern Ireland's Strangford Narrows, and the Rotech Lunar Energy system, to be installed off the South Korean Coast. A fourth type of tidal energy system studied is a novel JPL/Caltech hydraulic energy transfer system that uses submerged turbine blades which are mechanically attached to adjacent high-pressure pumps, instead of to adjacent electrical turbines. The generated highpressure water streams are combined and transferred to an onshore hydroelectric plant by means of a closed-cycle pipeline. The hydraulic energy transfer system was found to be cost competitive, and it allows all electronics to be placed onshore, thus greatly reducing maintenance costs and corrosion problems. It also eliminates the expenses of conditioning and transferring multiple offshore power lines and of building offshore platforms embedded in the sea floor.

Biological effects of diethylene glycol (DEG) and produced waters (PWs) released from offshore activities: a multi-biomarker approach with the sea bass Dicentrarchus labrax.

PubMed

Stefania, Gorbi; Maura, Benedetti; Claudia, Virno Lamberti; Barbara, Pisanelli; Ginevra, Moltedo; Francesco, Regoli

2009-11-01

Diethylene glycol (DEG) is largely used during oil and gas exploitation by offshore platforms. The aim of this work was to investigate if this compound induces direct molecular/cellular effects in marine organisms, or indirectly modulate those of produced waters (PWs). Sea bass (Dicentrarchus labrax) were exposed to DEG dosed alone or in combination with PWs from an Adriatic platform. A wide array of analysed biomarkers included cytochrome P450-dependent enzymatic activity, bile metabolites, glutathione S-transferases, acetylcholinesterase, peroxisomal proliferation, antioxidant defences (catalase, glutathione reductase, glutathione peroxidases, glutathione), total oxyradical scavenging capacity, malondialdehyde and DNA integrity (single strand breaks and frequency of micronuclei). Results did not reveal marked effects of DEG, while PWs influenced the biotransformation system, the oxidative status and the onset of genotoxic damages. Co-exposures caused only limited differences of biomarker responses at some experimental conditions, overall suggesting a limited biological impact of DEG at levels normally deriving from offshore activities.

Tectonic structure and petroleum potential of TayabasBay southeast Luzon, Philippines

NASA Astrophysics Data System (ADS)

Bacud, Jaime; Moore, Aidan; Lee, Chao-Skiing

Tayabas Bay is one of four offshore Philippine areas where the Australian GeologicalSurvey Organization and the Philippine Department of Energy conducted a cooperative marine seismic, gravity, magnetic, bathymetry and geochemical survey. The project acquired new seismic data and reprocessed the 1983 World Bank seismic sections which were all integrated with previous oil company data. the absence of wells drilled offshore, interpretation of offshore seismic data was complemented by onshore well log information and stratigraphy of the Bondoc Peninsula. Geochemistry data, both offshore and onshore, were analyzed to confirm the presence of mature source rocks and hydrocarbon migration. A new seismic interpretation has revealed the structure of this tectonically active geologically complex area. A major structural feature interpreted in offshore Tayabas Bay was a N-NW-trending strike-slip fault which is believed to be a northern splay of the Sibuyan Sea Fault. The authors named this fault the Tayabas Bay Fault and due to its association with the Philippine Fault System the movement is assumed to be left-lateral. The present study suggested the presence of a prolific source rock in the Middle Miocene Vigo Formation and/or the Late Oligocene to Early Miocene Panaon Limestone. Oil and gas generation have been and are occurring in the Bondoc Sub-basin. Two groups of reservoirs were identified, the shelf carbonates beneath the Middle Miocene shales on the Marinduque Platform and the early Middle Miocene carbonates and basin-floor clastics near the base of the Vigo Formation. Carbonate reservoirs are believed to be present in traps formed when the Late Oligocene to Early Miocene carbonate reefs and shelf deposits of the Panaon Limestone were buried by the Middle Miocene shales. A later set of traps was formed and possibly superimposed by the intense deformation associated with the Philippine Fault System which has continued from the Late Pliocene up to the present. Evaluation for hydrocarbon reserves of several possible traps identified three significant leads, namely the Yuni Lead in the south, the Mulanay in the central area and the Mabio in the North.

Operational experience in underwater photogrammetry

NASA Astrophysics Data System (ADS)

Leatherdale, John D.; John Turner, D.

Underwater photogrammetry has become established as a cost-effective technique for inspection and maintenance of platforms and pipelines for the offshore oil industry. A commercial service based in Scotland operates in the North Sea, USA, Brazil, West Africa and Australia. 70 mm cameras and flash units are built for the purpose and analytical plotters and computer graphics systems are used for photogrammetric measurement and analysis of damage, corrosion, weld failures and redesign of underwater structures. Users are seeking simple, low-cost systems for photogrammetric analysis which their engineers can use themselves.

Health monitoring of offshore structures using wireless sensor network: experimental investigations

NASA Astrophysics Data System (ADS)

Chandrasekaran, Srinivasan; Chitambaram, Thailammai

2016-04-01

This paper presents a detailed methodology of deploying wireless sensor network in offshore structures for structural health monitoring (SHM). Traditional SHM is carried out by visual inspections and wired systems, which are complicated and requires larger installation space to deploy while decommissioning is a tedious process. Wireless sensor networks can enhance the art of health monitoring with deployment of scalable and dense sensor network, which consumes lesser space and lower power consumption. Proposed methodology is mainly focused to determine the status of serviceability of large floating platforms under environmental loads using wireless sensors. Data acquired by the servers will analyze the data for their exceedance with respect to the threshold values. On failure, SHM architecture will trigger an alarm or an early warning in the form of alert messages to alert the engineer-in-charge on board; emergency response plans can then be subsequently activated, which shall minimize the risk involved apart from mitigating economic losses occurring from the accidents. In the present study, wired and wireless sensors are installed in the experimental model and the structural response, acquired is compared. The wireless system comprises of Raspberry pi board, which is programmed to transmit the acquired data to the server using Wi-Fi adapter. Data is then hosted in the webpage for further post-processing, as desired.

Effects of Second-Order Hydrodynamics on a Semisubmersible Floating Offshore Wind Turbine: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bayati, I.; Jonkman, J.; Robertson, A.

2014-07-01

The objective of this paper is to assess the second-order hydrodynamic effects on a semisubmersible floating offshore wind turbine. Second-order hydrodynamics induce loads and motions at the sum- and difference-frequencies of the incident waves. These effects have often been ignored in offshore wind analysis, under the assumption that they are significantly smaller than first-order effects. The sum- and difference-frequency loads can, however, excite eigenfrequencies of the system, leading to large oscillations that strain the mooring system or vibrations that cause fatigue damage to the structure. Observations of supposed second-order responses in wave-tank tests performed by the DeepCwind consortium at themore » MARIN offshore basin suggest that these effects might be more important than originally expected. These observations inspired interest in investigating how second-order excitation affects floating offshore wind turbines and whether second-order hydrodynamics should be included in offshore wind simulation tools like FAST in the future. In this work, the effects of second-order hydrodynamics on a floating semisubmersible offshore wind turbine are investigated. Because FAST is currently unable to account for second-order effects, a method to assess these effects was applied in which linearized properties of the floating wind system derived from FAST (including the 6x6 mass and stiffness matrices) are used by WAMIT to solve the first- and second-order hydrodynamics problems in the frequency domain. The method has been applied to the OC4-DeepCwind semisubmersible platform, supporting the NREL 5-MW baseline wind turbine. The loads and response of the system due to the second-order hydrodynamics are analysed and compared to first-order hydrodynamic loads and induced motions in the frequency domain. Further, the second-order loads and induced response data are compared to the loads and motions induced by aerodynamic loading as solved by FAST.« less

Psychosocial burden among offshore drilling platform employees.

PubMed

Leszczyńska, Irena; Jeżewska, Maria

2010-01-01

Conditions of work on offshore drilling platforms are particularly hard due to extreme environmental situations created both by nature and technological processes. Oil drilling workers employed on the open sea are potentially exposed to permanently high stress. Apart from the obvious objective factors affecting drilling platform employees, a great role in the general work-related stress level is played by the working conditions and work-related psychosocial factors, defined according to Karask's concept as demands, control, and social support. A total of 184 drill platform workers were examined using objective and subjective research methods. The level of subjective stress among drilling platform workers is lower than the level of objective stress and the stress resulting from prognoses related with specificity of work in extremely hard conditions (audit). The examinations of drilling platform workers reveal a positive role of stress in psychological adaptation, being a special case of the "work ethos" and attachment to the firm. In such investigations of work-related stress on drilling platforms, which are very specific workplaces, a multi-aspect character, sociological and economic aspects, organizational culture conditions in the firm, and a tendency to conceal ailments and the stress experienced should be taken into account. It is important to apply measures referring to at least three different types of evidence (objective demands, subjective stress, health problems reported). Otherwise, the result reflecting work-related stress may not be objective and far from the truth.

Application of a newly built semi-submersible vessel for transportation of a tension leg platform

NASA Astrophysics Data System (ADS)

Zhang, Dagang; Sun, Weiying; Fan, Zhixia

2012-09-01

Transportation of tension leg platform (TLP) structures for a long distance has always been associated with the use of a heavy semi-transport vessel. The requirements of this type of vessel are always special, and their availability is limited. To prepare for the future development of South China Sea deepwater projects, the China Offshore Oil Engineering Corporation has recently built a heavy lift transport vessel-Hai Yang Shi You 278. This semi-submersible vessel has a displacement capacity of 50k DWT, and a breath of 42 meters. Understanding the vessel's applicability and preparing it for use in future deepwater projects are becoming imminent needs. This paper reviews the current critical issues associated with TLP transportation and performs detailed analysis of the designed TLP during load-out and transportation. The newly built COOEC transportation vessel HYSY 278 was applied to dry transport of the TLP structure from the COOEC fabrication yard in Qingdao to an oil field in South China Sea. The entire process included the load-out of the TLP structure from the landsite of the fabrication yard, the offloading and float-on of the platform from the vessel, the dry transport of the TLP over a long distance, and the final offloading of the platform. Both hydrodynamic and structure analysis were performed to evaluate the behavior of the transport vessel and TLP structure. Special attention was paid to critical areas associated with the use of this new vessel, along with any potential limitations. The results demonstrate that HYSY 278 can effectively be used for transporting the structure with proper arrangement and well-prepared operation. The procedure and details were presented on the basis of the study results. Special attention was also given to discussion on future use based on the results from the analysis.

30 CFR 250.905 - How do I get approval for the installation, modification, or repair of my platform?

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF...., cathodic protection systems; jacket design; pile foundations; drilling, production, and pipeline risers and... design or analysis of the platform. Examples of relevant data include information on waves, wind, current...

Structural Health Monitoring of Large Structures

NASA Technical Reports Server (NTRS)

Kim, Hyoung M.; Bartkowicz, Theodore J.; Smith, Suzanne Weaver; Zimmerman, David C.

1994-01-01

This paper describes a damage detection and health monitoring method that was developed for large space structures using on-orbit modal identification. After evaluating several existing model refinement and model reduction/expansion techniques, a new approach was developed to identify the location and extent of structural damage with a limited number of measurements. A general area of structural damage is first identified and, subsequently, a specific damaged structural component is located. This approach takes advantage of two different model refinement methods (optimal-update and design sensitivity) and two different model size matching methods (model reduction and eigenvector expansion). Performance of the proposed damage detection approach was demonstrated with test data from two different laboratory truss structures. This space technology can also be applied to structural inspection of aircraft, offshore platforms, oil tankers, ridges, and buildings. In addition, its applications to model refinement will improve the design of structural systems such as automobiles and electronic packaging.

Development of Decision Analysis Specifically for Arctic Offshore Drilling Islands.

DTIC Science & Technology

1985-12-01

the decision analysis method will - give tradeoffs between costs and design wave height, production and depth • :of water for an oil platform , etc...optimizing the type of platform that is best suited for a particular site has become an extremely difficult decision. Over fifty- one different types of...drilling and production platforms have been identified for the Arctic environment, with new concepts being developed - every year, Boslov et al (198j

Analysis of Earthquake Recordings Obtained from the Seafloor Earthquake Measurement System (SEMS) Instruments Deployed off the Coast of Southern California

USGS Publications Warehouse

Boore, D.M.; Smith, C.E.

1999-01-01

For more than 20 years, a program has been underway to obtain records of earthquake shaking on the seafloor at sites offshore of southern California, near oil platforms. The primary goal of the program is to obtain data that can help determine if ground motions at offshore sites are significantly different than those at onshore sites; if so, caution may be necessary in using onshore motions as the basis for the seismic design of oil platforms. We analyze data from eight earthquakes recorded at six offshore sites; these are the most important data recorded on these stations to date. Seven of the earthquakes were recorded at only one offshore station; the eighth event was recorded at two sites. The earthquakes range in magnitude from 4.7 to 6.1. Because of the scarcity of multiple recordings from any one event, most of the analysis is based on the ratio of spectra from vertical and horizontal components of motion. The results clearly show that the offshore motions have very low vertical motions compared to those from an average onshore site, particularly at short periods. Theoretical calculations find that the water layer has little effect on the horizontal components of motion but that it produces a strong spectral null on the vertical component at the resonant frequency of P waves in the water layer. The vertical-to-horizontal ratios for a few selected onshore sites underlain by relatively low shear-wave velocities are similar to the ratios from offshore sites for frequencies less than about one-half the water layer P-wave resonant frequency, suggesting that the shear-wave velocities beneath a site are more important than the water layer in determining the character of the ground motions at lower frequencies.

Venezuela offshore oil and gas production development: Past, present and future

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perez La Salvia, H.; Schwartz, E.; Contreras, M.

1995-12-01

This paper presents a short history of offshore oil and gas production in Venezuela starting in Lake Maracaibo in 1923. The main emphasis has been the results of the recent R and D and the exploratory offshore programs in areas like Orinoco Delta located in the Atlantic Ocean, Northeast and Northwest Venezuela in the Caribbean sea. In the R and D offshore program the main objectives were: (1) To establish the local environmental, oceanographical, geotechnical and seismicity conditions for the Venezuelan Continental Platform. (2) To give a technical support to the PDVSA Operating Affiliates during the exploratory programs including: (a)more » to develop accurate drilling vessel positioning systems; (b) evaluation of sea bottom geotechnical conditions for safely operating the jack-ups and drilling vessels involved in the exploratory wells and (c) to identify those areas which because of their special nature require further investigation to establish preliminary type of platforms required for the areas to be developed or to evaluate other solutions proposed by Foreign Consultant Engineering Companies to the PDVSA Operating Affiliated Companies. The main objective of PDVSA for the coming future will be to develop the North of Paria Gas Field through the initially named Christopher Columbus Project now Sucre Gas, S.A., a consortium conformed by LaGoven, S.A. Shell, Exxon and Mitsubishi. objective of this paper is to give an idea of the history of the Venezuelan Oil and Gas Offshore development giving emphasis to the results of the INTEVEP S.A. Red offshore program and to show some results of the particular characteristics of oceanographical, environmental, geotechnical and seismic conditions in the main areas evaluated during the exploratory program: Orinoco Delta, Gulf of Paria and North of Paria.« less

Impact of the slab dip change onto the deformation partitioning in the northern Lesser Antilles oblique subduction zone (Antigua-Virgin Islands)

NASA Astrophysics Data System (ADS)

Laurencin, Muriel; Marcaillou, Boris; Klingelhoefer, Frauke; Graindorge, David; Lebrun, Jean-Frédéric; Laigle, Mireille; Lallemand, Serge

2017-04-01

Marine geophysical cruises Antithesis (2013-2016) investigate the impact of the variations in interplate geometry onto margin tectonic deformation along the strongly oblique Lesser Antilles subduction zone. A striking features of this margin is the drastic increase in earthquake number from the quiet Barbuda-St Martin segment to the Virgin Islands platform. Wide-angle seismic data highlight a northward shallowing of the downgoing plate: in a 150 km distance from the deformation front, the slab dipping angle in the convergence direction decreases from 12° offshore of Antigua Island to 7° offshore of Virgin Islands. North-South wide-angle seismic line substantiates a drastic slab-dip change that likely causes this northward shallowing. This dip change is located beneath the southern tip of the Virgin Islands platform where the Anegada Passage entails the upper plate. Based on deep seismic lines and bathymetric data, the Anegada Passage is a 450 km long W-E trending set of pull-apart basins and strike-slip faults that extends from the Lesser Antilles accretionary prism to Puerto Rico. The newly observed sedimentary architecture within pull-apart Sombrero and Malliwana basins indicates a polyphased tectonic history. A past prominent NW-SE extensive to transtensive phase, possibly related to the Bahamas Bank collision, opened the Anegada Passage as previously published. Transpressive tectonic evidences indicate that these structures have been recently reactivated in an en-echelon sinistral strike-slip system. The interpreted strain ellipsoid is consistent with deformation partitioning. We propose that the slab northward shallowing increases the interplate coupling and the seismic activity beneath the Virgin Islands platform comparatively to the quiet Barbuda-St Martin segment. It is noteworthy that the major tectonic partitioning structure in the Lesser Antilles forearc is located above the slab dip change where the interplate seismic coupling increases.

The U.S. Department of Energy's Reference Facility for Offshore Renewable Energy (RFORE): A New Platform for Research and Development (Invited)

NASA Astrophysics Data System (ADS)

Shaw, W. J.

2013-12-01

Offshore renewable energy represents a significant but essentially untapped electricity resource for the U.S. Offshore wind energy is attractive for a number of reasons, including the feasibility of using much larger and more efficient wind turbines than is possible on land. In many offshore regions near large population centers, the diurnal maximum in wind energy production is also closely matched to the diurnal maximum in electricity demand, easing the balancing of generation and load. Currently, however, the cost of offshore wind energy is not competitive with other energy sources, including terrestrial wind. Two significant contributing reasons for this are the cost of offshore wind resource assessment and fundamental gaps in knowledge of the behavior of winds and turbulence in the layer of the atmosphere spanned by the sweep of the turbine rotor. Resource assessment, a necessary step in securing financing for a wind project, is conventionally carried out on land using meteorological towers erected for a year or more. Comparable towers offshore are an order of magnitude more expensive to install. New technologies that promise to reduce these costs, such as Doppler lidars mounted on buoys, are being developed, but these need to be validated in the environment in which they will be used. There is currently no facility in the U.S. that can carry out such validations offshore. Research needs include evaluation and improvement of hub-height wind forecasts from regional forecast models in the marine boundary layer, understanding of turbulence characteristics that affect turbine loads and wind plant efficiency, and development of accurate representations of sea surface roughness and atmospheric thermodynamic stability on hub height winds. In response to these needs for validation and research, the U.S. Department of Energy is developing the Reference Facility for Offshore Renewable Energy (RFORE). The RFORE will feature a meteorological tower with wind, temperature, humidity, and turbulence sensors at nominally eight levels to a maximum measurement height of at least 100 m. In addition, remote sensing systems for atmospheric dynamic and thermodynamic profiles, sea state measurements including wave spectra, and subsurface measurements of current, temperature, and salinity profiles will be measured. Eventually, measurements from the platform are anticipated to include monitoring of marine and avian life as well as bats. All data collected at the RFORE will be archived and made available to all interested users. The RFORE is currently planned to be built on the structure of the Chesapeake Light Tower, approximately 25 km east of Virginia Beach, Virginia. This development is an active collaboration among U.S. DOE headquarters staff, the National Renewable Energy Laboratory (NREL), and Pacific Northwest National Laboratory (PNNL). NREL will design, construct, and operate the facility. PNNL will develop the research agenda, including the data archive. This presentation emphasizes the measurement capabilities of the facility in the context of research applications, user access to the data through the archive, and plans for user engagement and research management of the facility.

Assessment of multi-phase movements in a gas-gathering pipeline and the relevance to on-line, real-time corrosion monitoring and inhibitor injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, M.A.; Asperger, R.G.

1988-01-01

A study was conducted to determine the time required for aqueous fluid to travel 100 miles (160 km) from an offshore platform in the Gulf of Mexico to landfill. If this time is short, the corrosivity of the water at landfall may be used as the basis for setting the offshore corrosion inhibitor injection rates. But, for this particular system, the traveling time was found to be long, greater than 65 days. Therefore, the corrosivity as measured on-shore can not be used for online, real-time adjustments of the offshore, corrosion inhibitor chemical pumps.

The Feasibility of Wind and Solar Energy Application for Oil and Gas Offshore Platform

NASA Astrophysics Data System (ADS)

Tiong, Y. K.; Zahari, M. A.; Wong, S. F.; Dol, S. S.

2015-04-01

Renewable energy is an energy which is freely available in nature such as winds and solar energy. It plays a critical role in greening the energy sector as these sources of energy produce little or no pollution to environment. This paper will focus on capability of renewable energy (wind and solar) in generating power for offshore application. Data of wind speeds and solar irradiation that are available around SHELL Sabah Water Platform for every 10 minutes, 24 hours a day, for a period of one year are provided by SHELL Sarawak Sdn. Bhd. The suitable wind turbine and photovoltaic panel that are able to give a high output and higher reliability during operation period are selected by using the tabulated data. The highest power output generated using single wind energy application is equal to 492 kW while for solar energy application is equal to 20 kW. Using the calculated data, the feasibility of renewable energy is then determined based on the platform energy demand.

Use of high-resolution geophysical and geotechnical techniques for artificial reef site selection, west Cameron planning area, offshore Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pope, D.L.; Wagner, J.B.

1988-09-01

Before siting oil and gas platforms on the sea floor as artificial reefs offshore Louisiana, potentially hazardous and unstable geologic conditions must be identified and evaluated to assess their possible impacts on platform stability. Geologic and man-made features can be identified and assessed from high-resolution geophysical techniques (3.5-7.0 kHz echograms, single-channel seismic, and side-scan sonar). Such features include faults, diapirs, scarps, channels, gas seeps, irregular sea floor topography, mass wasting deposits (slumps, slides, and debris flows), pipelines, and other subsea marine equipment. Geotechnical techniques are utilized to determine lithologic and physical properties of the sediments for correlation with the geophysicalmore » data. These techniques are used to develop a series of geologic maps, cross sections, and pipeline and platform-location maps. Construction of echo-character maps from 3.5-kHz data provides an analysis of near-bottom sedimentation processes (turbidity currents and debris flows).« less

Monitoring compaction and compressibility changes in offshore chalk reservoirs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dean, G.; Hardy, R.; Eltvik, P.

1994-03-01

Some of the North Sea's largest and most important oil fields are in chalk reservoirs. In these fields, it is important to measure reservoir compaction and compressibility because compaction can result in platform subsidence. Also, compaction drive is a main drive mechanism in these fields, so an accurate reserves estimate cannot be made without first measuring compressibility. Estimating compaction and reserves is difficult because compressibility changes throughout field life. Installing of accurate, permanent downhole pressure gauges on offshore chalk fields makes it possible to use a new method to monitor compressibility -- measurement of reservoir pressure changes caused by themore » tide. This tidal-monitoring technique is an in-situ method that can greatly increase compressibility information. It can be used to estimate compressibility and to measure compressibility variation over time. This paper concentrates on application of the tidal-monitoring technique to North Sea chalk reservoirs. However, the method is applicable for any tidal offshore area and can be applied whenever necessary to monitor in-situ rock compressibility. One such application would be if platform subsidence was expected.« less

Fire Protection Materials

NASA Technical Reports Server (NTRS)

1980-01-01

Avco has drawn upon its heat shield experience to develop a number of widely-accepted commercial fire protection materials. Originating from NASA's space shuttle thermal protection system, one such material is Chartek 59 fireproofing, an intumescent epoxy coating specifically designed for outdoor use by industrial facilities dealing with highly flammable products such as oil refineries and chemical plants. The coating is applied usually by spray gun to exterior structural steel conduits, pipes and valves, offshore platforms and liquefied petroleum gas tanks. Fireproofing provides two types of protection: ablation or dissipation of heat by burn-off and "intumescence" or swelling; the coating swells to about five times its original size, forming a protective blanket of char which retards transfer of heat to the metal structure preventing loss of structural strength and possible collapse which would compound the fire fighting problem.

Positive organizational behavior and safety in the offshore oil industry: Exploring the determinants of positive safety climate.

PubMed

Hystad, Sigurd W; Bartone, Paul T; Eid, Jarle

2014-01-01

Much research has now documented the substantial influence of safety climate on a range of important outcomes in safety critical organizations, but there has been scant attention to the question of what factors might be responsible for positive or negative safety climate. The present paper draws from positive organizational behavior theory to test workplace and individual factors that may affect safety climate. Specifically, we explore the potential influence of authentic leadership style and psychological capital on safety climate and risk outcomes. Across two samples of offshore oil-workers and seafarers working on oil platform supply ships, structural equation modeling yielded results that support a model in which authentic leadership exerts a direct effect on safety climate, as well as an indirect effect via psychological capital. This study shows the importance of leadership qualities as well as psychological factors in shaping a positive work safety climate and lowering the risk of accidents.

Positive organizational behavior and safety in the offshore oil industry: Exploring the determinants of positive safety climate

PubMed Central

Hystad, Sigurd W.; Bartone, Paul T.; Eid, Jarle

2013-01-01

Much research has now documented the substantial influence of safety climate on a range of important outcomes in safety critical organizations, but there has been scant attention to the question of what factors might be responsible for positive or negative safety climate. The present paper draws from positive organizational behavior theory to test workplace and individual factors that may affect safety climate. Specifically, we explore the potential influence of authentic leadership style and psychological capital on safety climate and risk outcomes. Across two samples of offshore oil-workers and seafarers working on oil platform supply ships, structural equation modeling yielded results that support a model in which authentic leadership exerts a direct effect on safety climate, as well as an indirect effect via psychological capital. This study shows the importance of leadership qualities as well as psychological factors in shaping a positive work safety climate and lowering the risk of accidents. PMID:24454524

Growth and demise of a Paleogene isolated carbonate platform of the Offshore Indus Basin, Pakistan: effects of regional and local controlling factors

NASA Astrophysics Data System (ADS)

Shahzad, Khurram; Betzler, Christian; Ahmed, Nadeem; Qayyum, Farrukh; Spezzaferri, Silvia; Qadir, Anwar

2018-03-01

Based on high-resolution seismic and well datasets, this paper examines the evolution and drowning history of a Paleocene-Eocene carbonate platform in the Offshore Indus Basin of Pakistan. This study uses the internal seismic architecture, well log data as well as the microfauna to reconstruct factors that governed the carbonate platform growth and demise. Carbonates dominated by larger benthic foraminifera assemblages permit constraining the ages of the major evolutionary steps and show that the depositional environment was tropical within oligotrophic conditions. With the aid of seismic stratigraphy, the carbonate platform edifice is resolved into seven seismic units which in turn are grouped into three packages that reflect its evolution from platform initiation, aggradation with escarpment formation and platform drowning. The carbonate factory initiated as mounds and patches on a Cretaceous-Paleocene volcanic complex. Further, the growth history of the platform includes distinct phases of intraplatform progradation, aggradation, backstepping and partial drownings. The youngest succession as late-stage buildup records a shift from benthic to pelagic deposition and marks the final drowning in the Early Eocene. The depositional trend of the platform, controlled by the continuing thermal subsidence associated with the cooling of volcanic margin lithosphere, was the major contributor of the accommodation space which supported the vertical accumulation of shallow water carbonate succession. Other factors such as eustatic changes and changes in the carbonate producers as a response to the Paleogene climatic perturbations played secondary roles in the development and drowning of these buildups.

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures must I take when I conduct drilling... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow...

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2014 CFR

2014-07-01

... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures must I take...

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow...

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2013 CFR

2013-07-01

... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures must I take...

30 CFR 250.406 - What additional safety measures must I take when I conduct drilling operations on a platform that...

Code of Federal Regulations, 2012 CFR

2012-07-01

... when I conduct drilling operations on a platform that has producing wells or has other hydrocarbon flow... OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations General Requirements § 250.406 What additional safety measures must I take...

Joint Offshore Wind Field Monitoring with Spaceborne SAR and Platform-Based Doppler LIDAR Measurements

NASA Astrophysics Data System (ADS)

Jacobsen, S.; Lehner, S.; Hieronimus, J.; Schneemann, J.; Kuhn, M.

2015-04-01

The increasing demand for renewable energy resources has promoted the construction of offshore wind farms e.g. in the North Sea. While the wind farm layout consists of an array of large turbines, the interrelation of wind turbine wakes with the remaining array is of substantial interest. The downstream spatial evolution of turbulent wind turbine wakes is very complex and depends on manifold parameters such as wind speed, wind direction and ambient atmospheric stability conditions. To complement and validate existing numerical models, corresponding observations are needed. While in-situ measurements with e.g. anemometers provide a time-series at the given location, the merits of ground-based and space- or airborne remote sensing techniques are indisputable in terms of spatial coverage. Active microwave devices, such as Scatterometer and Synthetic Aperture Radar (SAR), have proven their capabilities of providing sea surface wind measurements and particularly SAR images reveal wind variations at a high spatial resolution while retaining the large coverage area. Platform-based Doppler LiDAR can resolve wind fields with a high spatial coverage and repetition rates of seconds to minutes. In order to study the capabilities of both methods for the investigation of small scale wind field structures, we present a direct comparison of observations obtained by high resolution TerraSAR-X (TS-X) X-band SAR data and platform-based LiDAR devices at the North Sea wind farm alpha ventus. We furthermore compare the results with meteorological data from the COSMO-DE model run by the German Weather Service DWD. Our study indicates that the overall agreement between SAR and LiDAR wind fields is good and that under appropriate conditions small scale wind field variations compare significantly well.

Hydrodynamic analysis of floating platform for special purposes under complex water environment

NASA Astrophysics Data System (ADS)

Ma, Guang-ying; Yao, Yun-long

2018-03-01

This article studied a new floating offshore platform for special purposes, which was assembled by standard floating modules. By using ANSYS AQWA software, the hydrodynamic model of the platform was established. The time history responses of the platform motions and the cable tension forces were calculate under complex water environments, such as wind, wave, current and mooring. The results showed that the tension of the four cables are far less than the breaking tension of the cable, so that the cable will not break. This study can be referenced by the relevant researchers and engineers.

Development of a computer model to predict platform station keeping requirements in the Gulf of Mexico using remote sensing data

NASA Technical Reports Server (NTRS)

Barber, Bryan; Kahn, Laura; Wong, David

1990-01-01

Offshore operations such as oil drilling and radar monitoring require semisubmersible platforms to remain stationary at specific locations in the Gulf of Mexico. Ocean currents, wind, and waves in the Gulf of Mexico tend to move platforms away from their desired locations. A computer model was created to predict the station keeping requirements of a platform. The computer simulation uses remote sensing data from satellites and buoys as input. A background of the project, alternate approaches to the project, and the details of the simulation are presented.

A novel ultrasonic phased array inspection system to NDT for offshore platform structures

NASA Astrophysics Data System (ADS)

Wang, Hua; Shan, Baohua; Wang, Xin; Ou, Jinping

2007-01-01

A novel ultrasonic phased array detection system is developed for nondestructive testing (NDT). The purpose of the system is to make acquisition of data in real-time from 64-element ultrasonic phased array transducer, and to enable real- time processing of the acquired data. The system is composed of five main parts: master unit, main board, eight transmit/receive units, a 64-element transducer and an external PC. The system can be used with 64 element transducers, excite 32 elements, receive and sample echo signals form 32 elements simultaneously at 62.5MHz with 8 bit precision. The external PC is used as the user interface showing the real time images and controls overall operation of the system through USB serial link. The use of Universal Serial Bus (USB) improves the transform speed and reduces hardware interface complexity. The program of the system is written in Visual C++.NET and is platform independent.

Study on Vortex-Induced Motions of A New Type of Deep Draft Multi-Columns FDPSO

NASA Astrophysics Data System (ADS)

Gu, Jia-yang; Xie, Yu-lin; Zhao, Yuan; Li, Wen-juan; Tao, Yan-wu; Huang, Xiang-hong

2018-03-01

A numerical simulation and an experimental study on vortex-induced motion (VIM) of a new type of deep draft multi-columns floating drilling production, storage and offloading (FDPSO) are presented in this paper. The main dimension, the special variable cross-section column and the cabin arrangement of the octagonal pontoon are introduced based on the result. The numerical simulation is adapted to study the effects of current incidence angles and reduced velocities on this platform's sway motion response. The 300 m water depth equivalent truncated mooring system is adopted for the model tests. The model tests are carried out to check the reliability of numerical simulation. The results consist of surge, sway and yaw motions, as well as motion trajectories. The maximum sway amplitudes for different types of offshore platform is also studied. The main results show that the peak frequencies of sway motion under different current incidence angles and reduced velocities vary around the natural frequency. The analysis result of flow field indicates that the change of distribution of vortex in vertical presents significant influences on the VIM of platform. The trend of sway amplitude ratio curve of this new type FDPSO differs from the other types of platform. Under 45° current incidence angle, the sway amplitude of this new type of FDPSO is much smaller than those of other types of offshore platform at 4.4 ≤ V r ≤ 8.9. The typical `8' shape trajectory does not appear in the platform's motion trajectories.

Deadlines set for new U. K. offshore safety rules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-12-14

This paper reports on new U.K. offshore safety regulations-inspired by Lord Cullen's 1990 report spawned by the 1987 Piper Alpha platform accident which will take effect May 31, 1993, for new installations. The U.K. Health and Safety Executive (HSE) said its proposed regulations, required for operators or owners to gain HSE approval for each fixed or mobile installation, was put before Parliament Nov. 27. That gives opposition parties 40 days to call for debate and possible amendment before the proposals become law.

An Adaptive Coordinated Control for an Offshore Wind Farm Connected VSC Based Multi-Terminal DC Transmission System

NASA Astrophysics Data System (ADS)

Kumar, M. Ajay; Srikanth, N. V.

2015-01-01

The voltage source converter (VSC) based multiterminal high voltage direct current (MTDC) transmission system is an interesting technical option to integrate offshore wind farms with the onshore grid due to its unique performance characteristics and reduced power loss via extruded DC cables. In order to enhance the reliability and stability of the MTDC system, an adaptive neuro fuzzy inference system (ANFIS) based coordinated control design has been addressed in this paper. A four terminal VSC-MTDC system which consists of an offshore wind farm and oil platform is implemented in MATLAB/ SimPowerSystems software. The proposed model is tested under different fault scenarios along with the converter outage and simulation results show that the novel coordinated control design has great dynamic stabilities and also the VSC-MTDC system can supply AC voltage of good quality to offshore loads during the disturbances.

Spinoff from a Mooncraft Technology

NASA Technical Reports Server (NTRS)

1988-01-01

Avco Specialty Materials' Chartek III fireproofing provides longterm fire protection for structural steel in high risk industrial applications such as structural conduits, pipes and valves of offshore platforms, and storage tanks used in hydrocarbon processing industry. In the presence of fire, Chartek III fire-proofing provides two kinds of protection. One of them is ablation, technique used on Apollo involving dissipation of heat by burnoff. The other is called intumescence or swelling. Heat causes the Chartek coating to swell to a thickness six times greater than when it was applied forming a protective blanket of char that retards transfer of heat to the steel structure. Mesh reinforcement keeps the char intact and reduces metal fatigue. Chartek provides fire protection for as much as two or three hours depending on the type of fire and the thickness of the coating applied.

Chicxulub impact basin: Gravity characteristics and implications for basin morphology and deep structure

NASA Technical Reports Server (NTRS)

Sharpton, Virgil L.; Burke, Kevin; Hall, Stuart A.; Lee, Scott; Marin, Luis E.; Suarez, Gerardo; Quezada-Muneton, Juan Manuel; Urrutia-Fucugauchi, Jaime

1993-01-01

The K-T-aged Chicxulub Impact Structure is buried beneath the Tertiary carbonate rocks of the Northern Yucatan Platform. Consequently its morphology and structure are poorly understood. Reprocessed Bouguer (onshore) and Free Air (offshore) gravity data over Northern Yucatan reveal that Chicxulub may be a 200-km-diameter multi-ring impact basin with at least three concentric basin rings. The positions of these rings follow the square root of 2 spacing rule derived empirically from analysis of multi-ring basins on other planets indicating that these rings probably correspond to now-buried topographic basin rings. A forward model of the gravity data along a radial transect from the southwest margin of the structure indicates that the Chicxulub gravity signature is compatible with this interpretation. We estimate the basin rim diameter to be 204 +/- 16 km and the central peak ring diameter (D) is 104 +/- 6 km.

Providing emergency medical care to offshore oil and gas platforms in the Gulf of Mexico using telemedicine

NASA Astrophysics Data System (ADS)

Bouabene, Anis

2002-08-01

UTMB is developing with industrial partners the "24/7 telemedicine triage project" to provide emergency medical care to offshore oil and gas rigs and platforms in the Gulf of Mexico. The oil and gas industry is second only to the US department of defense in the number of employees stationed in remote areas. Providing medical care to such populations is logistically complex and expensive. In addition, emergency evacuation is often time-consuming and poses risks for both patients and medical crews. By utilizing high-resolution videoconferencing technology, through a satellite communication, patient visits will be conducted in real time and will provide more informed decisions about the need for more extensive treatment, thereby reducing unnecessary evacuations. In addition, patients who require evacuation will receive a higher standard of care while waiting for transport to a medical facility. UTMB physicians report that 39% of all patients from offshore facilities treated in the emergency department, could have been successfully treated through telemedicine without being evacuated to a hospital. The telemedicine project will employ standard procedures for medical triage, in which patients are directed to appropriate medical experts based on their symptoms or type of injury.

Paleohighs and Paleolows in the Basement Rocks of the Eastern Gulf of Mexico

NASA Astrophysics Data System (ADS)

Robinson, D.; Weislogel, A. L.

2017-12-01

The Eastern Gulf of Mexico has topography on the basement rocks composed of igneous and metamorphic rocks as well as some sedimentary rocks underneath a relatively thin salt layer with 3-6 km of topography relief. Paleohighs from south to north include Sarasota Arch, Middle Ground Arch/Southern Platform, Pensacola Arch, Conecuh Ridge Complex, Baldwin High, Wiggins Arch and Choctaw Ridge Complex. Paleolows from south to north include South Florida Basin, Tampa Embayment, Apalachicola Basin/Desoto Canyon Salt Basin, Conecuh Embayment, Manila Embayment and the Mississippi Interior Salt Basin. The topography on the basement is a result of several collisions between Laurentian and Gondwana to produce Pangea with final suturing during Pennsylvanian time and also from extension in Late Triassic to Early Cretaceous time as a result of the opening of the Gulf and rotation of Yucatan. Heterogeneities related to previous collisions may have also factored into producing these paleohighs and paleolows. A series of grabens and half-grabens, trending northeast-southwest from northwest-southeast directed extension and with the sedimentary rocks, exist on the continents and appear to be present in the offshore under the salt. We know the paleolows were depositional pathways to funnel sediments from onshore to offshore via water and wind in Jurassic and maybe Cretaceous times. Many tectonic models call for the paleohighs and paleolows to be structurally controlled; however, finding the faults called upon to control the "horst and graben" structures is challenging. We present data from several seismic studies that questions the idea that these paleohighs and paleolows are the result of horst and graben extension. Half grabens exist in the offshore with graben bounding faults northeast-southwest; however, down is to the north instead of the anticipated down to the south. Instead, the basement paleohighs and paleolows in the offshore Eastern Gulf of Mexico may be the result of preexisting lithologic and structural weaknesses in conjunction with lithospheric thinning. Some of the basement paleohighs and paleolows in the onshore are related to the buried Appalachian fold-thrust belt.

Onshore and offshore basins of northeast Libya: Their origin and hydrocarbon potential

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shegewi, O.M.

1992-01-01

A comprehensive data base of more than 3000 km of seismic lines, gravity and magnetic data, more than 30 subsurface well logs, and surface geology data were utilized to examine and interpret the sedimentary and tectonic history of the onshore and offshore parts of Northeast Libya and their hydrocarbon potential. The Dernah-Tobruk and Benghazi offshore basins form the northern parts of the study area. The Cyrenaica Stable Platform represents the southern parts. The Sirual Trough stretches E-W and opens into the Antelat Trough in the west. Between these elements is the uplifted areas of the Al Jabal Al Akhdar. Sixmore » principal tectonic phases were responsible for the formation and development of these structural elements: the pre-Mesozoic phase, the Triassic-Jurassic rifting phase, the Neocomian and the Aptian-Albian renewed rifting phases, the Late Cretaceous-Paleocene uplifting phase; and the Eocene-Middle Oligocene rifting phase. Oceanic crust of probable Aptian-Albian age is evident on the seismic lines north of the master fault marking the southern boundary of the rift separating the north African plate and Apulia. The western boundary of the Dernah High displayed clearly NE-SW strike-slip movement of these trajectories. Oceanic crust is also present west of the Dernah High. Positive gravity and magnetic anomalies traverse parallel to the boundary of this oceanic plate Mesogea. The prerequisites for commercial hydrocarbon production are present in abundance. Reservoirs ranging in age from Paleozoic clastics in the Cyrenaica Stable Platform to Mesozoic and Tertiary carbonates throughout the rest of the region. Several deep sites for the generation of hydrocarbons were also present, including the rifted northern parts of the Dernah-Tobruk basin, the Antelat Trough and the Cyrenaica Passive Margin. The Cretaceous and Tertiary section in the study area contain several potential seal rocks. Several potential trap types are also present.« less

A system identification technique based on the random decrement signatures. Part 2: Experimental results

NASA Technical Reports Server (NTRS)

Bedewi, Nabih E.; Yang, Jackson C. S.

1987-01-01

Identification of the system parameters of a randomly excited structure may be treated using a variety of statistical techniques. Of all these techniques, the Random Decrement is unique in that it provides the homogeneous component of the system response. Using this quality, a system identification technique was developed based on a least-squares fit of the signatures to estimate the mass, damping, and stiffness matrices of a linear randomly excited system. The results of an experiment conducted on an offshore platform scale model to verify the validity of the technique and to demonstrate its application in damage detection are presented.

SEASAT demonstration experiments with the offshore oil, gas and mining industries

NASA Technical Reports Server (NTRS)

Mourad, A. G.; Robinson, A. C.; Balon, J. E.

1979-01-01

Despite its failure, SEASAT-1 acquired a reasonable volume of data that can be used by industrial participants on a non-real-time basis to prove the concept of microwave sensing of the world's oceans from a satellite platform. The amended version of 8 experimental plans are presented, along with a description of the satellite, its instruments, and the data available. Case studies are summarized for the following experiments: (1) Beaufort Sea oil, gas, and Arctic operations; (2) Labrador Sea oil, gas, and sea ice; (3) Gulf of Mexico pipelines; (4) U.S. East Coast offshore oil and gas; (5) worldwide offshore drilling and production operations; (6) Equatorial East Pacific Ocean mining; (7) Bering Sea ice project; and (8) North Sea oil and gas.

Task 1: Whole-body concentrations of elements in kelp bass (Paralabrax clathratus), kelp rockfish (Sebastes atrovirens), and Pacific sanddab (Citharichthys sordidus) from offshore oil platforms and natural areas in the Southern California Bight

USGS Publications Warehouse

Love, Milton S.

2009-01-01

Resource managers are concerned that offshore oil platforms in the Southern California Bight may be contributing to environmental contaminants accumulated by marine fishes. To examine this possibility, 18 kelp bass (Paralabrax clathratus), 80 kelp rockfish (Sebastes atrovirens), and 98 Pacific sanddab (Citharichthys sordidus) were collected from five offshore oil platforms and 10 natural areas during 2005-2006 for whole-body analysis of 63 elements. The natural areas, which served as reference sites, were assumed to be relatively uninfluenced by contaminants originating from platforms. Forty-two elements were excluded from statistical comparisons for one of three reasons: they consisted of major cations that were unlikely to accumulate to potentially toxic concentrations under ambient exposure conditions; they were not detected by the analytical procedures; or they were detected at concentrations too low to yield reliable quantitative measurements. The remaining 21 elements consisted of aluminum, arsenic, barium, cadmium, chromium, cobalt, copper, gallium, iron, lead, lithium, manganese, mercury, nickel, rubidium, selenium, strontium, tin, titanium, vanadium, and zinc. Statistical comparisons of these 21 elements indicated that none consistently exhibited higher concentrations at oil platforms than at natural areas. Eight comparisons yielded significant interaction effects between total length (TL) of the fish and the two habitat types (oil platforms and natural areas). This indicated that relations between certain elemental concentrations (i.e., copper, rubidium, selenium, tin, titanium, and vanadium) and habitat type varied by TL of affected fish species. To better understand these interactions, we examined elemental concentrations in very small and very large individuals of affected species. Although significant interactions were detected for rubidium, tin, and selenium in kelp rockfish, the concentrations of these elements did not differ significantly between oil platforms and natural areas over the TL range of sampled fish. However, for selenium, titanium, and vanadium in Pacific sanddab, small individuals (average TL, 13.0 cm) exhibited significantly lower concentrations at oil platforms than at natural areas, whereas large individuals (average TL, 27.5 cm) exhibited higher concentrations at oil platforms than at natural areas. For copper in Pacific sanddab, small individuals did not exhibit differences between oil platforms and natural areas, whereas large individuals exhibited significantly higher concentrations at oil platforms than at natural areas. On the other hand, for tin in Pacific sanddab, small individuals did not exhibit differences between oil platforms and natural areas, whereas large individuals exhibited significantly lower concentrations at oil platforms than at natural areas. Although concentrations of arsenic, cadmium, chromium, lead, mercury, and selenium in fishes from some platforms and natural areas equaled or exceeded literature-based toxicity thresholds for fish and fish-eating wildlife, studies are still needed to document evidence of toxicity from these elements. When estimates of elemental concentrations in skinless fillets were compared to risk-based consumption limits for humans, the concentrations of arsenic, cadmium, mercury, and tin in fish from a mix of oil platforms and natural areas were sufficiently elevated to suggest a need for further study of inorganic arsenic, cadmium, mercury, and tributyltin.

Study on the influence of attitude angle on lidar wind measurement results

NASA Astrophysics Data System (ADS)

Han, Xiaochen; Dou, Peilin; Xue, Yangyang

2017-11-01

When carrying on wind profile measurement of offshore wind farm by shipborne Doppler lidar technique, the ship platform often produces motion response under the action of ocean environment load. In order to measure the performance of shipborne lidar, this paper takes two lidar wind measurement results as the research object, simulating the attitude of the ship in the ocean through the three degree of freedom platform, carrying on the synchronous observation test of the wind profile, giving an example of comparing the wind measurement data of two lidars, and carrying out the linear regression statistical analysis for all the experimental correlation data. The results show that the attitude angle will affect the precision of the lidar, The influence of attitude angle on the accuracy of lidar is uncertain. It is of great significance to the application of shipborne Doppler lidar wind measurement technology in the application of wind resources assessment in offshore wind power projects.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wayman, E. N.; Sclavounos, P. D.; Butterfield, S.

This article presents a collaborative research program that the Massachusetts Institute of Technology (MIT) and the National Renewable Energy Laboratory (NREL) have undertaken to develop innovative and cost-effective floating and mooring systems for offshore wind turbines in water depths of 10-200 m. Methods for the coupled structural, hydrodynamic, and aerodynamic analysis of floating wind turbine systems are presented in the frequency domain. This analysis was conducted by coupling the aerodynamics and structural dynamics code FAST [4] developed at NREL with the wave load and response simulation code WAMIT (Wave Analysis at MIT) [15] developed at MIT. Analysis tools were developedmore » to consider coupled interactions between the wind turbine and the floating system. These include the gyroscopic loads of the wind turbine rotor on the tower and floater, the aerodynamic damping introduced by the wind turbine rotor, the hydrodynamic damping introduced by wave-body interactions, and the hydrodynamic forces caused by wave excitation. Analyses were conducted for two floater concepts coupled with the NREL 5-MW Offshore Baseline wind turbine in water depths of 10-200 m: the MIT/NREL Shallow Drafted Barge (SDB) and the MIT/NREL Tension Leg Platform (TLP). These concepts were chosen to represent two different methods of achieving stability to identify differences in performance and cost of the different stability methods. The static and dynamic analyses of these structures evaluate the systems' responses to wave excitation at a range of frequencies, the systems' natural frequencies, and the standard deviations of the systems' motions in each degree of freedom in various wind and wave environments. This article in various wind and wave environments. This article explores the effects of coupling the wind turbine with the floating platform, the effects of water depth, and the effects of wind speed on the systems' performance. An economic feasibility analysis of the two concepts was also performed. Key cost components included the material and construction costs of the buoy; material and installation costs of the tethers, mooring lines, and anchor technologies; costs of transporting and installing the system at the chosen site; and the cost of mounting the wind turbine to the platform. The two systems were evaluated based on their static and dynamic performance and the total system installed cost. Both systems demonstrated acceptable motions, and have estimated costs of $1.4-$1.8 million, not including the cost of the wind turbine, the power electronics, or the electrical transmission.« less

Does EMF Emitted from In Situ Subsea Power Cables Affect the Composition of Deep Benthic Fish and Invertebrate Communities?

NASA Astrophysics Data System (ADS)

Bull, A. S.; Nishimoto, M.; Love, M.; Schroeder, D. M.

2016-02-01

A network of power cables is an important component of any offshore renewable energy generation facilities (e.g., wind and wave). The cables laid on the seafloor carry current that produces both electric and magnetic fields; the magnetic field, here called an electromagnetic field (EMF), is what is emitted from shielded cables. The cables, themselves, add hard, low-relief structure to what is typically soft-bottom habitat (mud or sand). Given that laboratory experiments show EMF can affect the behavior of some marine vertebrates and invertebrates, concern is raised over the potential ecological impacts of in situ power cables. Here we report an unusual comparative study of the effect of EMF emitted from in situ power cables on the fish and invertebrate communities of the deep coastal shelf environment. In the Santa Barbara Channel of southern California, subsea power cables, similar to those used in the offshore renewable energy industry, transmit electricity from shore to offshore oil and gas production platforms. A non-energized cable in the vicinity of energized cables afforded us the unusual opportunity to control for the effect of cable as hard, low relief habitat. We conducted three annual submersible surveys in October, 2012- 2014, at depths from 75 m to 210 m. We present results comparing observations along the energized and nonenergized cables and on the adjacent natural substrate.

Validation of a FAST model of the Statoil-Hywind Demo floating wind turbine

DOE PAGES

Driscoll, Frederick; Jonkman, Jason; Robertson, Amy; ...

2016-10-13

To assess the accuracy of the National Renewable Energy Laboratory's (NREL's) FAST simulation tool for modeling the coupled response of floating offshore wind turbines under realistic open-ocean conditions, NREL developed a FAST model of the Statoil Hywind Demo floating offshore wind turbine, and validated simulation results against field measurements. Field data were provided by Statoil, which conducted a comprehensive test measurement campaign of its demonstration system, a 2.3-MW Siemens turbine mounted on a spar substructure deployed about 10 km off the island of Karmoy in Norway. A top-down approach was used to develop the FAST model, starting with modeling themore » blades and working down to the mooring system. Design data provided by Siemens and Statoil were used to specify the structural, aerodynamic, and dynamic properties. Measured wind speeds and wave spectra were used to develop the wind and wave conditions used in the model. The overall system performance and behavior were validated for eight sets of field measurements that span a wide range of operating conditions. The simulated controller response accurately reproduced the measured blade pitch and power. In conclusion, the structural and blade loads and spectra of platform motion agree well with the measured data.« less

Recent developments in understanding the tectonic evolution of the Southern California offshore area: Implications for earthquake-hazard analysis

USGS Publications Warehouse

Fisher, M.A.; Langenheim, V.E.; Nicholson, C.; Ryan, H.F.; Sliter, R.W.

2009-01-01

During late Mesozoic and Cenozoic time, three main tectonic episodes affected the Southern California offshore area. Each episode imposed its unique structural imprint such that early-formed structures controlled or at least influenced the location and development of later ones. This cascaded structural inheritance greatly complicates analysis of the extent, orientation, and activity of modern faults. These fault attributes play key roles in estimates of earthquake magnitude and recurrence interval. Hence, understanding the earthquake hazard posed by offshore and coastal faults requires an understanding of the history of structural inheritance and modifi-cation. In this report we review recent (mainly since 1987) findings about the tectonic development of the Southern California offshore area and use analog models of fault deformation as guides to comprehend the bewildering variety of offshore structures that developed over time. This report also provides a background in regional tectonics for other chapters in this section that deal with the threat from offshore geologic hazards in Southern California. ?? 2009 The Geological Society of America.

Gulf of Mexico and Caribbean Sea Data and Model Base Report

DTIC Science & Technology

1979-07-01

The source levels and spectral characteristics of merchant ships, drill rigs, and seismic profiling sources are reason- ably well known. Lacking...better data, fishing vessels are assumed to be 10 dB quieter than merchar• ships; production platforms are assumed to be similar to drill rigs, corrected...scope of the problem presented by production platforms, mobile drill rigs, and seismic profilers. 5. Impact on Exercise Planning Offshore oil industry

Genetic connectivity in scleractinian corals across the Northern Gulf of Mexico: oil/gas platforms, and relationship to the Flower Garden Banks.

PubMed

Sammarco, Paul W; Brazeau, Daniel A; Sinclair, James

2012-01-01

The 3,000 oil/gas structures currently deployed in the northern Gulf of Mexico (GOM) provide hard substratum for marine organisms in a region where such has been rare since the Holocene. The major exception to this are the Flower Garden Banks (FGB). Corals are known to have colonized oil/gas platforms around the FGB, facilitating biogeographic expansion. We ask the question, what are the patterns of genetic affinity in these coral populations. We sampled coral tissue from populations of two species occurring on oil and gas platforms: Madracis decactis (hermatype) and Tubastraea coccinea (invasive ahermatype). We sampled 28 platforms along four transects from 20 km offshore to the continental shelf edge off 1) Matagorda Island, TX; 2) Lake Sabine, TX; 3) Terrebonne Bay, LA; and 4) Mobile, AL. The entire population of M. decactis was sampled between depths of 5 m and 37 m. T. coccinea populations were sub-sampled. Genetic variation was assessed using the PCR-based Amplified Fragment Length Polymorphisms (AFLPs). Data were analyzed via AFLPOP and STRUCTURE. Genetic connectivity among M. decactis platform populations was highest near the FGB and decreased to the east. Connectivity increased again in the eastern sector, indicating isolation between the populations from different sides of the Mississippi River (Transects 3 and 4). A point-drop in genetic affinity (relatedness) at the shelf edge south of Terrebonne Bay, LA indicated a population differing from all others in the northern GOM. Genetic affinities among T. coccinea were highest in the west and decreased to the east. Very low genetic affinities off Mobile, AL indicated a dramatic difference between those populations and those west of the Mississippi River, apparently a formidable barrier to larval dispersal.

Genetic Connectivity in Scleractinian Corals across the Northern Gulf of Mexico: Oil/Gas Platforms, and Relationship to the Flower Garden Banks

PubMed Central

Sammarco, Paul W.; Brazeau, Daniel A.; Sinclair, James

2012-01-01

The 3,000 oil/gas structures currently deployed in the northern Gulf of Mexico (GOM) provide hard substratum for marine organisms in a region where such has been rare since the Holocene. The major exception to this are the Flower Garden Banks (FGB). Corals are known to have colonized oil/gas platforms around the FGB, facilitating biogeographic expansion. We ask the question, what are the patterns of genetic affinity in these coral populations. We sampled coral tissue from populations of two species occurring on oil and gas platforms: Madracis decactis (hermatype) and Tubastraea coccinea (invasive ahermatype). We sampled 28 platforms along four transects from 20 km offshore to the continental shelf edge off 1) Matagorda Island, TX; 2) Lake Sabine, TX; 3) Terrebonne Bay, LA; and 4) Mobile, AL. The entire population of M. decactis was sampled between depths of 5 m and 37 m. T. coccinea populations were sub-sampled. Genetic variation was assessed using the PCR-based Amplified Fragment Length Polymorphisms (AFLPs). Data were analyzed via AFLPOP and STRUCTURE. Genetic connectivity among M. decactis platform populations was highest near the FGB and decreased to the east. Connectivity increased again in the eastern sector, indicating isolation between the populations from different sides of the Mississippi River (Transects 3 and 4). A point-drop in genetic affinity (relatedness) at the shelf edge south of Terrebonne Bay, LA indicated a population differing from all others in the northern GOM. Genetic affinities among T. coccinea were highest in the west and decreased to the east. Very low genetic affinities off Mobile, AL indicated a dramatic difference between those populations and those west of the Mississippi River, apparently a formidable barrier to larval dispersal. PMID:22558066

76 FR 7189 - Trunkline Gas Company, LLC; Notice of Request Under Blanket Authorization

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-09

... Ship Shoal T-27 Platform and appurtenant facilities located in Ship Shoal 274, Offshore Louisiana... as more fully set forth in the application, which is open to the public for inspection. The filing...

Job stress, mental health, and accidents among offshore workers in the oil and gas extraction industries.

PubMed

Cooper, C L; Sutherland, V J

1987-02-01

Psychosocial and occupational stressors among 194 male employees on drilling rig and production platform installations in the United Kingdom and Dutch sectors of the North Sea were studied. Mental well-being and job satisfaction were also assessed, with attention to the incidence of accidents offshore. This occupational group were found to be much less satisfied with their jobs than their onshore counterparts. Although overall mental well-being compared favorably with that of the general population, levels of anxiety were significantly higher. Multivariate analysis showed "relationships at work and at home" to be a strong predictor of both job dissatisfaction and mental ill-health. Type A coronary-prone behavior was also found to be a significant predictor of reduced mental well-being and increased accident rates offshore.

Satellite data relay and platform locating in oceanography. Report of the In Situ Ocean Science Working Group

NASA Technical Reports Server (NTRS)

Chase, R.; Cote, C.; Davis, R. E.; Dugan, J.; Frame, D. D.; Halpern, D.; Kerut, E.; Kirk, R.; Mcgoldrick, L.; Mcwilliams, J. C.

1983-01-01

The present and future use of satellites to locate offshore platforms and relay data from in situ sensors to shore was examined. A system of the ARGOS type will satisfy the increasing demand for oceanographic information through data relay and platform location. The improved ship navigation provided by the Global Positioning System (GPS) will allow direct observation of currents from underway ships. Ocean systems are described and demand estimates on satellite systems are determined. The capabilities of the ARGOS system is assessed, including anticipated demand in the next decade.

Gravity study of Libya;Evaluation and Integration with Geological Data

NASA Astrophysics Data System (ADS)

Ben Suleman, abdunnur; Saheel, Ahmed

2016-04-01

Libya is located on the Mediterranean foreland of the African Shield and covers an area of approximately 1.8 million square kilometers. Since Early Paleozoic time, Libya has been a site of deposition of large sheets of continental clastics and several transgressions and regressions by the seas with consequent accumulations of a wide variety of sedimentary rocks. Several tectonic cycles affected the area and shaped the geological setting of the country. However, the regional geology and the structural framework have been highly influenced by the Caledonian, Hercynian, and Alpine tectonic events. As a result, a total of seven sedimentary basins, namely Ghadames, Murzuq, Al Kufra, Al Butnan, Sirt, and the Offshore Pelagian Basin, were developed and were separated by intervening uplifts and platforms ( Gargaf, Tibesti, Nafusah and Cyrenaica platform). Apart from Sirt and the offshore basins, all the above mentioned basins are active since Early Paleozoic time and received several thousand feet of sediments. The capability of providing regional information on the structure of sedimentary basins makes gravity mapping, in conjunction with geological information, potentially powerful tools. In this study we used gravity mapping as our primary tool of investigation however, we also used all available geological information to better understand the regional tectonics. The gravity dataset that were used in the Gravity compilation project of Libya is not homogenous. As a result, some irregularities, apparent spikes or misties, and large shifts were obtained and were taken into consideration. Evaluation of gravity Maps of Libya and their integration with geological data provide a better understanding of the role that gravity mapping plays in the geological exploration of sedimentary basins. Results confirm the known Sirt Basin regional tectonic elements and the possible presence of NW-SE lateral wrench tectonics, crossing Ajdabiya Trough at the center of Sirt Basin. The residual gravity map supports new interpretation of the Sirwal Trough in Northern Cyrenaica. Results also indicate shallow crust along the present day coast line of Al Jabal Al Akhdar, steeply dipping toward the offshore. The depo-center of Ghadames Basin cannot be precisely defined due to the lack of gravity coverage. However, Murzuq Basin is well defined regionally, in spite of gravity gaps which make the overall coverage in the southern basins inadequate for precise interpretation.

The Development of a Finite Volume Method for Modeling Sound in Coastal Ocean Environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, Wen; Yang, Zhaoqing; Copping, Andrea E.

: As the rapid growth of marine renewable energy and off-shore wind energy, there have been concerns that the noises generated from construction and operation of the devices may interfere marine animals’ communication. In this research, a underwater sound model is developed to simulate sound prorogation generated by marine-hydrokinetic energy (MHK) devices or offshore wind (OSW) energy platforms. Finite volume and finite difference methods are developed to solve the 3D Helmholtz equation of sound propagation in the coastal environment. For finite volume method, the grid system consists of triangular grids in horizontal plane and sigma-layers in vertical dimension. A 3Dmore » sparse matrix solver with complex coefficients is formed for solving the resulting acoustic pressure field. The Complex Shifted Laplacian Preconditioner (CSLP) method is applied to efficiently solve the matrix system iteratively with MPI parallelization using a high performance cluster. The sound model is then coupled with the Finite Volume Community Ocean Model (FVCOM) for simulating sound propagation generated by human activities in a range-dependent setting, such as offshore wind energy platform constructions and tidal stream turbines. As a proof of concept, initial validation of the finite difference solver is presented for two coastal wedge problems. Validation of finite volume method will be reported separately.« less

Height system connection between island and mainland using a hydrodynamic model: a case study connecting the Dutch Wadden islands to the Amsterdam ordnance datum (NAP)

NASA Astrophysics Data System (ADS)

Slobbe, D. C.; Klees, R.; Verlaan, M.; Zijl, F.; Alberts, B.; Farahani, H. H.

2018-03-01

We present an efficient and flexible alternative method to connect islands and offshore tide gauges with the height system on land. The method uses a regional, high-resolution hydrodynamic model that provides total water levels. From the model, we obtain the differences in mean water level (MWL) between tide gauges at the mainland and at the islands or offshore platforms. Adding them to the MWL relative to the national height system at the mainland's tide gauges realizes a connection of the island and offshore platforms with the height system on the mainland. Numerical results are presented for the connection of the Dutch Wadden islands with the national height system (Normaal Amsterdams Peil, NAP). Several choices of the period over which the MWLs are computed are tested and validated. The best results were obtained when we computed the MWL only over the summer months of our 19-year simulation period. Based on this strategy, the percentage of connections for which the absolute differences between the observation- and model-derived MWL differences are ≤ 1 cm is about 34% (46 out of 135 possible leveling connections). In this case, for each Wadden island we can find several connections that allow the transfer of NAP with (sub-)centimeter accuracy.

Western Continental Margin of India - Re-look using potential field data

NASA Astrophysics Data System (ADS)

Rajaram, M.; S P, A.

2008-05-01

The Western Continental Margin of India (WCMI) evolved as a result of rifting between India and Madagascar that took place during mid Cretaceous (~88Ma).The WCMI is equally important in terms of natural resources as well as research point of view. The major tectonic elements in the western offshore includes the Laxmi and Chagos- Laccadive ridge dividing the WCMI and the adjoining Arabian sea into two basins, Pratap Ridge, Alleppey platform etc. Different theories have been proposed for the evolution of each of these tectonic elements. In the current paper we look at geopotential data on the west coast of India and the western off-shore. The data sets utilized include Satellite derived High Resolution Free Air Gravity data over the off-shore, Bouguer data onland, Champ Satellite Magnetic data, published Marine Magnetic data collected by ONGC, NIO, ground magnetic data over west cost collected by IIG and available aeromagnetic data. From the free air gravity anomaly the structural details of the western offshore can be delineated. The Euler depths of FAG depict deep solutions associated with Pratap Ridge, Comorin Ridge, the west coast fault and the Laxmi Ridge. These may be associated with continental margin and continental fragments. From the aeromagnetic and marine magnetic data it is evident that the West Coast Fault is dissected at several places. The shallow circular feature associated with Bombay High is evident both on the FAG and the analytic signal derived from satellite Magnetic data. The crustal magnetic thickness from MF5 lithospheric model of the Champ appears to suggest that the continental crust extends up to the Chagos- Laccadive ridge. Based on the analysis of these geopotential data sets the various theories for the evolution of the WCMI will be evaluated and these results will be presented.

Natural frequency and vibration analysis of jacket type foundation for offshore wind power

NASA Astrophysics Data System (ADS)

Hung, Y.-C.; Chang, Y.-Y.; Chen, S.-Y.

2017-12-01

There are various types of foundation structure for offshore wind power, engineers may assess the condition of ocean at wind farm, and arrange the transportation, installation of each structure members, furthermore, considering the ability of manufacture steel structure as well, then make an optimum design. To design jacket offshore structure, unlike onshore cases, offshore structure also need to estimate the wave excitation effect. The aim of this paper is to study the difference of natural frequency between different kinds of structural stiffness and discuss the effect of different setting of boundary condition during analysis, besides, compare this value with the natural frequency of sea wave, in order to avoid the resonance effect. In this paper, the finite element analysis software ABAQUS is used to model and analyze the natural vibration behavior of the jacket structure.

Space Radar Image of Oil Slicks

NASA Image and Video Library

1999-04-15

This is a radar image of an offshore drilling field about 150 km 93 miles west of Bombay, India, in the Arabian Sea. The dark streaks are extensive oil slicks surrounding many of the drilling platforms, which appear as bright white spots.

Towards a mature offshore wind energy technology - guidelines from the opti-OWECS project

NASA Astrophysics Data System (ADS)

Kühn, M.; Bierbooms, W. A. A. M.; van Bussel, G. J. W.; Cockerill, T. T.; Harrison, R.; Ferguson, M. C.; Göransson, B.; Harland, L. A.; Vugts, J. H.; Wiecherink, R.

1999-01-01

The article reviews the main results of the recent European research project Opti-OWECS (Structural and Economic Optimisation of Bottom-Mounted Offshore Wind Energy Converters'), which has significantly improved the understanding of the requirements for a large-scale utilization of offshore wind energy. An integrated design approach was demonstrated for a 300 MW offshore wind farm at a demanding North Sea site. Several viable solutions were obtained and one was elaborated to include the design of all major components. Simultaneous structural and economic optimization took place during the different design stages. An offshore wind energy converter founded on a soft-soft monopile was tailored with respect to the distinct characteristics of dynamic wind and wave loading. The operation and maintenance behaviour of the wind farm was analysed by Monte Carlo simulations. With an optimized maintenance strategy and suitable hardware a high availability was achieved. Based upon the experience from the structural design, cost models for offshore wind farms were developed and linked to a European database of the offshore wind energy potential. This enabled the first consistent estimate of cost of offshore wind energy for entire European regions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hurst, J.M.; Lapointe, P.A.; Nyein, U.K.

Three Oligocene-Miocene carbonate depositional morphologies commonly occur: shoals, reefs, and isolated platforms. Lenticular shoals (0-25 m thick, 1 km long) are stacked and intercalated with siliciclastic mudstones. Facies include trough/festoon cross-bedded benthic foram grainstones passing laterally and vertically into red-algal dominated graded-laminated beds, bioturbated silty calcareous mudstone, and siliciclastic sandy foram wackestone and packstone. The morphology and facies are hydrodynamically controlled. Pinnacle reefs (1-2 km[sup 2]) dominated by red-algae, branching corals, and large mollusks occur on structure or aligned within shelf mudstones. The latter location reflects low sedimentation rates and hydrodynamic control. Isolated platforms (up to 150 km[sup 2]) aremore » environmental mosaics of marginal path reefs and shoals, interior lagoons, and islands plus marginal slopes. Facies are similar to shoals and reefs except there are more muddy fabrics and less high-energy facies. They develop on tilted fault blocks or eroded submerged arcs in the offshore Gulf of Martaban, distal to the ancestral Irrawaddy delta.« less

Airfoil family design for large offshore wind turbine blades

NASA Astrophysics Data System (ADS)

Méndez, B.; Munduate, X.; San Miguel, U.

2014-06-01

Wind turbine blades size has scaled-up during last years due to wind turbine platform increase especially for offshore applications. The EOLIA project 2007-2010 (Spanish Goverment funded project) was focused on the design of large offshore wind turbines for deep waters. The project was managed by ACCIONA Energia and the wind turbine technology was designed by ACCIONA Windpower. The project included the design of a wind turbine airfoil family especially conceived for large offshore wind turbine blades, in the order of 5MW machine. Large offshore wind turbines suffer high extreme loads due to their size, in addition the lack of noise restrictions allow higher tip speeds. Consequently, the airfoils presented in this work are designed for high Reynolds numbers with the main goal of reducing blade loads and mantainig power production. The new airfoil family was designed in collaboration with CENER (Spanish National Renewable Energy Centre). The airfoil family was designed using a evolutionary algorithm based optimization tool with different objectives, both aerodynamic and structural, coupled with an airfoil geometry generation tool. Force coefficients of the designed airfoil were obtained using the panel code XFOIL in which the boundary layer/inviscid flow coupling is ineracted via surface transpiration model. The desing methodology includes a novel technique to define the objective functions based on normalizing the functions using weight parameters created from data of airfoils used as reference. Four airfoils have been designed, here three of them will be presented, with relative thickness of 18%, 21%, 25%, which have been verified with the in-house CFD code, Wind Multi Block WMB, and later validated with wind tunnel experiments. Some of the objectives for the designed airfoils concern the aerodynamic behavior (high efficiency and lift, high tangential coefficient, insensitivity to rough conditions, etc.), others concern the geometry (good for structural design, compatibility for the different airfoil family members, etc.) and with the ultimate objective that the airfoils will reduce the blade loads. In this paper the whole airfoil design process and the main characteristics of the airfoil family are described. Some force coefficients for the design Reynolds number are also presented. The new designed airfoils have been studied with computational calculations (panel method code and CFD) and also in a wind tunnel experimental campaign. Some of these results will be also presented in this paper.

Biomass-Derived Porous Carbonaceous Aerogel as Sorbent for Oil-Spill Remediation.

PubMed

Wang, Zhuqing; Jin, Pengxiang; Wang, Min; Wu, Genhua; Dong, Chen; Wu, Aiguo

2016-12-07

We prepared a cost-effective, environmentally friendly carbonaceuous oil sorbent with a lotus effect structure using a simple one-pot hydrothermal reaction and a mild modification process. The carbonaceous oil sorbent can rapidly, efficiently, and continuously collect oil in situ from a water surface. This sorbent was unlike traditional sorbents because it was not dependent on the weight and volume of the sorption material. The sorbent was also successfully used to separate and collect crude oil from the water surface and can collect organic solvents underwater. This novel oil sorbent and oil-collection device can be used in case of emergency for organic solvent leakages, as well as leakages in tankers and offshore drilling platforms.

ASTER Views the Gulf of Mexico Oil Spill in Infrared May 1

NASA Image and Video Library

2010-05-04

NASA Terra spacecraft captured this image of the growing oil spill in the Gulf of Mexico on May 1, 2010. On April 20, 2010, an explosion destroyed the Deepwater Horizon oil platform operating offshore in the Gulf of Mexico.

Dynamic analysis of a 5-MW tripod offshore wind turbine by considering fluid-structure interaction

NASA Astrophysics Data System (ADS)

Zhang, Li-wei; Li, Xin

2017-10-01

Fixed offshore wind turbines usually have large underwater supporting structures. The fluid influences the dynamic characteristics of the structure system. The dynamic model of a 5-MW tripod offshore wind turbine considering the pile-soil system and fluid structure interaction (FSI) is established, and the structural modes in air and in water are obtained by use of ANSYS. By comparing low-order natural frequencies and mode shapes, the influence of sea water on the free vibration characteristics of offshore wind turbine is analyzed. On basis of the above work, seismic responses under excitation by El-Centro waves are calculated by the time-history analysis method. The results reveal that the dynamic responses such as the lateral displacement of the foundation and the section bending moment of the tubular piles increase substantially under the influence of the added-mass and hydrodynamic pressure of sea water. The method and conclusions presented in this paper can provide a theoretical reference for structure design and analysis of offshore wind turbines fixed in deep seawater.

Operational management of offshore energy assets

NASA Astrophysics Data System (ADS)

Kolios, A. J.; Martinez Luengo, M.

2016-02-01

Energy assets and especially those deployed offshore are subject to a variety of harsh operational and environmental conditions which lead to deterioration of their performance and structural capacity over time. The aim of reduction of CAPEX in new installations shifts focus to operational management to monitor and assess performance of critical assets ensuring their fitness for service throughout their service life and also to provide appropriate and effective information towards requalification or other end of life scenarios, optimizing the OPEX. Over the last decades, the offshore oil & gas industry has developed and applied various approaches in operational management of assets through Structural Health and Condition Monitoring (SHM/CM) systems which can be, at a certain level, transferable to offshore renewable installations. This paper aims to highlight the key differences between offshore oil & gas and renewable energy assets from a structural integrity and reliability perspective, provide a comprehensive overview of different approaches that are available and applicable, and distinguish the benefits of such systems in the efficient operation of offshore energy assets.

Performance of a Single Liquid Column Damper for the Control of Dynamic Responses of a Tension Leg Platform

NASA Astrophysics Data System (ADS)

Jaksic, V.; Wright, C.; Chanayil, Afeef; Faruque Ali, Shaikh; Murphy, Jimmy; Pakrashi, Vikram

2015-07-01

Tuned liquid column dampers have been proved to be successful in mitigating the dynamic responses of civil infrastructure. There have been some recent applications of this concept on wind turbines and this passive control system can help to mitigate responses of offshore floating platforms and wave devices. The control of dynamic responses of these devices is important for reducing loads on structural elements and facilitating operations and maintenance (O&M) activities. This paper outlines the use of a tuned single liquid column damper for the control of a tension leg platform supported wind turbine. Theoretical studies were carried out and a scaled model was tested in a wave basin to assess the performance of the damper. The tests on the model presented in this paper correspond to a platform with a very low natural frequency for surge, sway and yaw motions. For practical purposes, it was not possible to tune the liquid damper exactly to this frequency. The consequent approach taken and the efficiency of such approach are presented in this paper. Responses to waves of a single frequency are investigated along with responses obtained from wave spectra characterising typical sea states. The extent of control is quantified using peak and root mean squared dynamic responses respectively. The tests present some guidelines and challenges for testing scaled devices in relation to including response control mechanisms. Additionally, the results provide a basis for dictating future research on tuned liquid column damper based control on floating platforms.

Corrosion monitoring using high-frequency guided waves

NASA Astrophysics Data System (ADS)

Fromme, P.

2016-04-01

Corrosion can develop due to adverse environmental conditions during the life cycle of a range of industrial structures, e.g., offshore oil platforms, ships, and desalination plants. Generalized corrosion leading to wall thickness loss can cause the reduction of the strength and thus degradation of the structural integrity. The monitoring of corrosion damage in difficult to access areas can be achieved using high frequency guided waves propagating along the structure from accessible areas. Using standard ultrasonic wedge transducers with single sided access to the structure, guided wave modes were selectively generated that penetrate through the complete thickness of the structure. The wave propagation and interference of the different guided wave modes depends on the thickness of the structure. Laboratory experiments were conducted for wall thickness reduction due to milling of the steel structure. From the measured signal changes due to the wave mode interference the reduced wall thickness was monitored. Good agreement with theoretical predictions was achieved. The high frequency guided waves have the potential for corrosion damage monitoring at critical and difficult to access locations from a stand-off distance.

Corrosion monitoring using high-frequency guided ultrasonic waves

NASA Astrophysics Data System (ADS)

Fromme, Paul

2014-02-01

Corrosion develops due to adverse environmental conditions during the life cycle of a range of industrial structures, e.g., offshore oil platforms, ships, and desalination plants. Both pitting corrosion and generalized corrosion leading to wall thickness loss can cause the degradation of the structural integrity. The nondestructive detection and monitoring of corrosion damage in difficult to access areas can be achieved using high frequency guided waves propagating along the structure from accessible areas. Using standard ultrasonic transducers with single sided access to the structure, guided wave modes were generated that penetrate through the complete thickness of the structure. The wave propagation and interference of the different guided wave modes depends on the thickness of the structure. Laboratory experiments were conducted and the wall thickness reduced by consecutive milling of the steel structure. Further measurements were conducted using accelerated corrosion in a salt water bath and the damage severity monitored. From the measured signal change due to the wave mode interference the wall thickness reduction was monitored. The high frequency guided waves have the potential for corrosion damage monitoring at critical and difficult to access locations from a stand-off distance.

Montubi completes mile-long liquid ethylene pipeline project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-12-01

Montubi has completed the mile-long liquid ethylene pipeline project for Solvay S.p.A. at Vada, Italy, a line that extends 3.4 mi from an offshore unloading dock to an onshore gasification facility for Solvay's chemical plant at Rosignano. The 18 mo project included a mile-long 1750 ton jetty; one eight-leg main unloading platform; eight mooring dolphins plus four breasting dolphins; one small platform for firefighting pump units; and a concrete service road along the jetty.

30 CFR 250.901 - What industry standards must your platform meet?

Code of Federal Regulations, 2011 CFR

2011-07-01

...? 250.901 Section 250.901 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND... Constructing Fixed Offshore Platforms—Working Stress Design (incorporated by reference as specified in § 250... Stress Cracking Resistant Metallic Materials for Oilfield Equipment, (incorporated by reference as...

30 CFR 250.1628 - Design, installation, and operation of production systems.

Code of Federal Regulations, 2010 CFR

2010-07-01

... mechanical and electrical systems to be installed was approved by registered professional engineers. After... Installation of Offshore Production Platform Piping Systems; (3) Electrical system information including a plan... Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as...

Offshore Extension of Deccan Traps in Kachchh, Central Western India: Implications for Geological Sequestration Studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pandey, D. K., E-mail: pandey@ncaor.org; Pandey, A.; Rajan, S.

2011-03-15

The Deccan basalts in central western India are believed to occupy large onshore-offshore area. Using geophysical and geological observations, onshore sub-surface structural information has been widely reported. On the contrary, information about offshore structural variations has been inadequate due to scarcity of marine geophysical data and lack of onshore-offshore lithological correlations. Till date, merely a few geophysical studies are reported that gauge about the offshore extent of Deccan Traps and the Mesozoic sediments (pre-Deccan). To fill this gap in knowledge, in this article, we present new geophysical evidences to demonstrate offshore continuation of the Deccan volcanics and the Mesozoic sediments.more » The offshore multi-channel seismic and onshore-offshore lithological correlations presented here confirm that the Mesozoic sedimentary column in this region is overlain by 0.2-1.2-km-thick basaltic cover. Two separate phases of Mesozoic sedimentation, having very distinctive physical and lithological characteristics, are observed between overlying basaltic rocks and underlying Precambrian basement. Using onshore-offshore seismic and borehole data this study provides new insight into the extent of the Deccan basalts and the sub-basalt structures. This study brings out a much clearer picture than that was hitherto available about the offshore continuation of the Deccan Traps and the Mesozoic sediments of Kachchh. Further, its implications in identifying long-term storage of anthropogenic CO{sub 2} within sub-basalt targets are discussed. The carbon sequestration potential has been explored through the geological assessment in terms of the thickness of the strata as well as lithology.« less

Analysis of damaging process and crack propagation

NASA Astrophysics Data System (ADS)

Semenski, D.; Wolf, H.; Božić, Ž.

2010-06-01

Supervising and health monitoring of structures can assess the actual state of existing structures after initial loading or in the state of operation. Structural life management requires the integration of design and analysis, materials behavior and structural testing, as given for several examples. Procedure of survey of structural elements and criteria for their selection must be strongly defined as it is for the offshore gas platforms. Numerical analysis of dynamic loading is shown for the Aeolian vibrations of overhead transmission line conductors. Since the damper’s efficiency strongly depends on its position, the procedure of determining the optimum position of the damper is described. The optical method of caustics is established in isotropic materials for determination of the stress intensity factors (SIFs) of the cracks in deformed structures and is advantageously improved for the application to fiberreinforced composites. A procedure for simulation of crack propagation for multiple cracks was introduced and SIFs have been calculated by using finite element method. Crack growth of a single crack or a periodical array of cracks initiated at the stiffeners in a stiffened panel has been investigated.

30 CFR 250.918 - What are the CVA's primary duties during the installation phase?

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Platforms and..., and review the towing records; (iii) Launching and uprighting operations; (iv) Submergence operations..., and when the independent monitoring activities were conducted; (2) Describe the CVA's activities...

Welder

ERIC Educational Resources Information Center

Tech Directions, 2013

2013-01-01

Welding is used to create many things, from cars, trucks, and motorcycles to rail cars, ships, aircraft, rockets, and space stations. Welding is huge in the construction industry, too. Skyscrapers, bridges, and highways would be impossible to build without welding, as would oil and natural-gas pipelines, offshore oil platforms, wind turbines, and…

30 CFR 250.1727 - What information must I include in my final application to remove a platform or other facility?

Code of Federal Regulations, 2010 CFR

2010-07-01

... MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER... are placing the explosives inside or outside of the pilings; (3) If you will use divers or acoustic...

Summer and winter plankton fish assemblages around offshore oil and gas platforms in south-eastern Australia

NASA Astrophysics Data System (ADS)

Neira, Francisco J.

2005-06-01

Opportunistic plankton surveys were conducted within a 5-nmi radius of nine offshore oil and gas platforms in Bass Strait, south-eastern Australia, in February 1998 and 1999 (summer) and August 1998 (winter). The 108 day-night samples collected alongside (vertical tows) and nearby (surface and oblique tows) platforms yielded 1526 larval and early juvenile fishes representing 55 taxa from 45 families. Epipelagic/mesopelagic taxa dominated the catches, whereas hard/soft habitat-associated taxa were uncommon. Carangidae (36.2%) and Myctophidae (31.5%) dominated in summer and winter, respectively. The most abundant taxon was Trachurus declivis (Carangidae, 35.1%), followed by Bovichtus angustifrons (Bovichtidae, 8.7%), Scomberesox saurus (Scomberesocidae, 3.7%), Centroberyx affinis (Berycidae, 3.0%) and Arripis trutta (Arripidae, 1.7%). Fish concentrations (nos. per 100 m 3) alongside platforms did not differ significantly between day and night across all surveys. Likewise, concentrations nearby platforms in February 1999, including those of T. declivis, did not vary significantly by tow type (surface vs. oblique) or day vs. night. The far greater diversity and abundance recorded in February 1999 are likely the result of upwelling conditions over the eastern Bass Strait shelf during the sampling period, and which were not detected in February 1998. In the absence of data on adult fishes associated with the Bass Strait platforms, and given the limited availability of reefs directly around the area, it could be argued that some of the taxa caught may originate from spawning around neighboring natural reefs, particularly those off the Gippsland coastline and the south-east corner of mainland Australia. However, the prime position of the platforms almost right in the center of a productivity "hotspot" would have a confounding effect on the potential source(s) of larval fishes in that region of south-eastern Australia. The role of platforms as potential de-facto reefs for juvenile fishes in Bass Strait, as well as spawning areas, is discussed based on the findings of this study, the first on early stages of fishes around oil and gas platforms in Australia.

Deployment and Evaluation of the Helicopter In-Flight Tracking System (HITS)

NASA Technical Reports Server (NTRS)

Daskalakis, Anastasios; Martone, Patrick

2004-01-01

The Gulf of Mexico airspace has two major operating regions: low altitude offshore (below 7,000 ft) and high altitude oceanic (above 18,000 ft). Both regions suffer significant inefficiencies due to the lack of continuous surveillance during Instrument Flight Rules operations. Provision of surveillance in the offshore region is hindered by its low-altitude nature, which makes coverage by conventional radars economically infeasible. Significant portions of the oceanic sectors are inaccessible to shore-based sensors, as they are beyond line-of-sight. Two emerging surveillance technologies were assessed that are relatively low cost and can be deployed on offshore platforms Wide Area Multilateration and Automatic Dependent Surveillance Broadcast. Performance criteria were formulated using existing FAA specifications. Three configurations were developed and deployed representative of systems serving full-size and reduced-sized domestic terminal areas and an en-route/oceanic region. These configurations were evaluated during nine flight test periods using fixed- and rotary-wing aircraft.

Reduction of vortex induced forces and motion through surface roughness control

DOEpatents

Bernitsas, Michael M; Raghavan, Kamaldev

2014-04-01

Roughness is added to the surface of a bluff body in a relative motion with respect to a fluid. The amount, size, and distribution of roughness on the body surface is controlled passively or actively to modify the flow around the body and subsequently the Vortex Induced Forces and Motion (VIFM). The added roughness, when designed and implemented appropriately, affects in a predetermined way the boundary layer, the separation of the boundary layer, the level of turbulence, the wake, the drag and lift forces, and consequently the Vortex Induced Motion (VIM), and the fluid-structure interaction. The goal of surface roughness control is to decrease/suppress Vortex Induced Forces and Motion. Suppression is required when fluid-structure interaction becomes destructive as in VIM of flexible cylinders or rigid cylinders on elastic support, such as underwater pipelines, marine risers, tubes in heat exchangers, nuclear fuel rods, cooling towers, SPAR offshore platforms.

Low Head, Vortex Induced Vibrations River Energy Converter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernitsas, Michael B.; Dritz, Tad

2006-06-30

Vortex Induced Vibrations Aquatic Clean Energy (VIVACE) is a novel, demonstrated approach to extracting energy from water currents. This invention is based on a phenomenon called Vortex Induced Vibrations (VIV), which was first observed by Leonardo da Vinci in 1504AD. He called it ‘Aeolian Tones.’ For decades, engineers have attempted to prevent this type of vibration from damaging structures, such as offshore platforms, nuclear fuel rods, cables, buildings, and bridges. The underlying concept of the VIVACE Converter is the following: Strengthen rather than spoil vortex shedding; enhance rather than suppress VIV; harness rather than mitigate VIV energy. By maximizing andmore » utilizing this unique phenomenon, VIVACE takes this “problem” and successfully transforms it into a valuable resource for mankind.« less

Qatar: World Oil Report 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This paper reports on oil and gas operations that have taken a marked upturn in Qatar highlighted by production expansion projects. The long-delayed beginning of production from offshore supergiant North gas field was scheduled to begin at press time at a rate of 600 to 750 MMcfd and 50,000 bcpd. Delays in production startup were caused by gas leaks around casing strings in 14 of the 16 producing wells and by the Gulf war. The $1.3 billion Phase I of development included two 8-well platforms and three support structures, plus gas and condensate lines to an onshore NGL facility. Initially,more » gas will be utilized domestically. Eventually, 300 MMcfd will be re-injected into the old Dukhan oil field.« less

Low-smoke, halogenfree ship-offshore/onshore cables with improved flame retardance and fire resistance

NASA Astrophysics Data System (ADS)

Pedersen, J. R.; Holte, T. A.; Johansen, E.

Cables with improved fire resistance and flame retardance have been developed. They will continue to function at least 3 hours even at temperatures up to 1000 C and do not propagate fire when tested according to IEC 332 part 3 1982, category A. Made with halogenfree materials they give off no corrosive gases and very little visible smoke in cases of fire. Cables are made for power, signal and instrument installations in hospitals, high rise buildings, railroad cars, subways, on board ship, oil rigs and oil production platforms. The offshore cables are specially constructed to withstand the rugged climatic conditions in the North Sea area.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reggio, R.; Haun, R.

This paper reviews the engineering and design work along with the installation procedures for a Persian Gulf natural gas pipeline. OPMI Ltd., a joint venture of Offshore Pipelines, Inc., Houston, and Maritime Industrial Services Co., Ltd., United Arab Emirates (UAE), successfully completed this 57.4 mile, 16-inch gas export pipeline for Consolidated Transmissions Inc. The pipeline begins at a platform in the Mubarek field offshore Sharjah, UAE, and runs to a beach termination at the Dugas treatment plant, Jebel Ali, Dubai. The paper describes the site preparation required for installation of the pipeline along with the specific design of the pipelinemore » itself to deal with corrosion, welding processes, condensate dropout, and temperature gradients.« less

30 CFR 250.916 - What are the CVA's primary duties during the design phase?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Stress analyses; (vi) Material designations; (vii) Soil and foundation conditions; (viii) Safety factors... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Platforms and... pipeline risers, and riser tensioning systems; (ii) Turrets and turret-and-hull interfaces; (iii...

30 CFR 250.1004 - Safety equipment requirements for DOI pipelines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Pipelines and Pipeline Rights-of... a flow safety valve (FSV). (ii) For sulphur operations, incoming pipelines delivering gas to the power plant platform may be equipped with high- and low-pressure sensors (PSHL), which activate audible...

30 CFR 250.1004 - Safety equipment requirements for DOI pipelines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL... operations, incoming pipelines delivering gas to the power plant platform may be equipped with high- and low-pressure sensors (PSHL), which activate audible and visual alarms in lieu of requirements in paragraph (b...

A Crew Exposure Study. Volume I. Offshore.

DTIC Science & Technology

1982-03-15

in Percutaneous Penetra- tion in Man - Pesticides ," Archives of Environmental Health, Vol. 23, pp 208-211, 1971. 20. Bartek, M. J., et al., "Skin...OTO FI RCABNEISOS UT iA- 0 - . . -- • G. DISCHARGING OF HAZARDOUS WASTES FROM PLATFORMS 1. Middleditch, Brian S., Basile , Brenda, and Chang, Evelyn S

DISTINGUISHING CONTAMINANT FROM REEF EFFECTS ON MEIOFAUNA NEAR OFFSHORE HYDROCARBON PLATFORMS IN THE GULF OF MEXICO. (R825355)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

49 CFR 192.163 - Compressor stations: Design and construction.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Design of... building. Except for a compressor building on a platform located offshore or in inland navigable waters, each main compressor building of a compressor station must be located on property under the control of...

30 CFR 250.203 - Where can wells be located under an EP, DPP, or DOCD?

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Plans and Information General... reservoir management; (e) Location of drilling units and platforms; (f) Extent and thickness of the reservoir; (g) Geologic and other reservoir characteristics; (h) Minimizing environmental risk; (i...

Dynamic response signatures of a scaled model platform for floating wind turbines in an ocean wave basin

PubMed Central

Jaksic, V.; O'Shea, R.; Cahill, P.; Murphy, J.; Mandic, D. P.; Pakrashi, V.

2015-01-01

Understanding of dynamic behaviour of offshore wind floating substructures is extremely important in relation to design, operation, maintenance and management of floating wind farms. This paper presents assessment of nonlinear signatures of dynamic responses of a scaled tension-leg platform (TLP) in a wave tank exposed to different regular wave conditions and sea states characterized by the Bretschneider, the Pierson–Moskowitz and the JONSWAP spectra. Dynamic responses of the TLP were monitored at different locations using load cells, a camera-based motion recognition system and a laser Doppler vibrometer. The analysis of variability of the TLP responses and statistical quantification of their linearity or nonlinearity, as non-destructive means of structural monitoring from the output-only condition, remains a challenging problem. In this study, the delay vector variance (DVV) method is used to statistically study the degree of nonlinearity of measured response signals from a TLP. DVV is observed to create a marker estimating the degree to which a change in signal nonlinearity reflects real-time behaviour of the structure and also to establish the sensitivity of the instruments employed to these changes. The findings can be helpful in establishing monitoring strategies and control strategies for undesirable levels or types of dynamic response and can help to better estimate changes in system characteristics over the life cycle of the structure. PMID:25583866

NREL Software Aids Offshore Wind Turbine Designs (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2013-10-01

NREL researchers are supporting offshore wind power development with computer models that allow detailed analyses of both fixed and floating offshore wind turbines. While existing computer-aided engineering (CAE) models can simulate the conditions and stresses that a land-based wind turbine experiences over its lifetime, offshore turbines require the additional considerations of variations in water depth, soil type, and wind and wave severity, which also necessitate the use of a variety of support-structure types. NREL's core wind CAE tool, FAST, models the additional effects of incident waves, sea currents, and the foundation dynamics of the support structures.

On the Use of Coupled Wind, Wave, and Current Fields in the Simulation of Loads on Bottom-Supported Offshore Wind Turbines during Hurricanes: March 2012 - September 2015

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Eungsoo; Manuel, Lance; Curcic, Milan

In the United States, potential offshore wind plant sites have been identified along the Atlantic seaboard and in the Gulf of Mexico. It is imperative that we define external conditions associated with hurricanes and severe winter storms and consider load cases for which wind turbines may need to be designed. We selected two hurricanes, Ike (2008) and Sandy (2012), and investigated the effect these tropical storms would have on bottom-supported offshore wind turbines that were hypothetically in or close to their path as they made landfall. For realistic turbine loads assessment, it is important that the coupled influences of themore » changing wind, wave, and current fields are simulated throughout the evolution of the hurricanes. We employed a coupled model--specifically, the University of Miami Coupled Model (UMCM)--that integrates atmospheric, wave, and ocean components to produce needed wind, wave, and current data. The wind data are used to generate appropriate vertical wind profiles and full wind velocity fields including turbulence; the current field over the water column is obtained by interpolated discrete output current data; and short-crested irregular second-order waves are simulated using output directional wave spectra from the coupled model. We studied two monopile-supported offshore wind turbines sited in 20 meters of water in the Gulf of Mexico to estimate loads during Hurricane Ike, and a jacket space-frame platform-supported offshore wind turbine sited in 50 meters of water in the mid-Atlantic region to estimate loads during Hurricane Sandy. In this report we discuss in detail how the simulated hurricane wind, wave, and current output data are used in turbine loads studies. In addition, important characteristics of the external conditions are studied, including the relative importance of swell versus wind seas, aerodynamic versus hydrodynamic forces, current velocity effects, yaw control options for the turbine, hydrodynamic drag versus inertia forces, and soil-structure interaction effects. A detailed framework is presented that explains how coupled inputs can be included in turbine loads studies during a hurricane. This framework can aid in future efforts aimed at developing offshore wind turbine design criteria and load cases related to hurricanes.« less

An Indo-Pacific damselfish (Neopomacentrus cyanomos) in the Gulf of Mexico: origin and mode of introduction.

PubMed

Robertson, D Ross; Dominguez-Dominguez, Omar; Victor, Benjamin; Simoes, Nuno

2018-01-01

The Indo-West Pacific (IWP) coral-reef damselfish Neopomacentrus cyanomos is well established across the south-west Gulf of Mexico (SwGoMx). Comparisons of mtDNA sequences of the SwGoMx population with those from conspecifics from 16 sites scattered across its native geographic range show that the SwGoMx population is derived from two of four native lineages: one from the north-west Pacific Ocean, the other from the northern Indian Ocean. Three hypotheses address how this species was introduced to the SwGoMX: (1) aquarium release; (2) borne by cargo-ship; and (3) carried by offshore petroleum platform (petro-platform). The first is unlikely because this species rarely features in the aquarium trade, and " N. cyanomos " traded to the USA from the sole IWP source we are aware of are a misidentified congener, N. taeniurus . The second hypothesis is unlikely because shipping has not been associated with the introduction of alien damselfishes, there is little international shipping between the IWP and the SwGoMx, and voyages between those areas would be lengthy and along environmentally unfavorable routes. Various lines of evidence support the third hypothesis: (i) bio-fouled petro-platforms represent artificial reefs that can sustain large and diverse populations of tropical reef-fishes, including N. cyanomos in the SwGoMx; (ii) relocation of such platforms has been implicated in trans-oceanic introductions leading to establishment of non-native populations of such fishes; and (iii) genetic characteristics of the SwGoMx population indicate that it was established by a large and diverse group of founders drawn from the IWP regions where many petro-platforms currently in the SwGoMx and other Atlantic offshore oilfields originated.

An Indo-Pacific damselfish (Neopomacentrus cyanomos) in the Gulf of Mexico: origin and mode of introduction

PubMed Central

Dominguez-Dominguez, Omar; Victor, Benjamin; Simoes, Nuno

2018-01-01

The Indo-West Pacific (IWP) coral-reef damselfish Neopomacentrus cyanomos is well established across the south-west Gulf of Mexico (SwGoMx). Comparisons of mtDNA sequences of the SwGoMx population with those from conspecifics from 16 sites scattered across its native geographic range show that the SwGoMx population is derived from two of four native lineages: one from the north-west Pacific Ocean, the other from the northern Indian Ocean. Three hypotheses address how this species was introduced to the SwGoMX: (1) aquarium release; (2) borne by cargo-ship; and (3) carried by offshore petroleum platform (petro-platform). The first is unlikely because this species rarely features in the aquarium trade, and “N. cyanomos” traded to the USA from the sole IWP source we are aware of are a misidentified congener, N. taeniurus. The second hypothesis is unlikely because shipping has not been associated with the introduction of alien damselfishes, there is little international shipping between the IWP and the SwGoMx, and voyages between those areas would be lengthy and along environmentally unfavorable routes. Various lines of evidence support the third hypothesis: (i) bio-fouled petro-platforms represent artificial reefs that can sustain large and diverse populations of tropical reef-fishes, including N. cyanomos in the SwGoMx; (ii) relocation of such platforms has been implicated in trans-oceanic introductions leading to establishment of non-native populations of such fishes; and (iii) genetic characteristics of the SwGoMx population indicate that it was established by a large and diverse group of founders drawn from the IWP regions where many petro-platforms currently in the SwGoMx and other Atlantic offshore oilfields originated. PMID:29441235

Offshore Deterioration in the Mekong Delta, Vietnam

NASA Astrophysics Data System (ADS)

Stattegger, K.; Unverricht, D.; Heinrich, C.

2016-02-01

The interplay of river, tide and wave forcing controls shape and sedimentation at the front of the Mekong Delta. Specific hydro- and morphodynamic conditions in the western subaqueous part of the asymmetric Mekong Delta generate a sand ridge - channel system (SRCS) which is unique in subaqueous delta formation. This large-scale morphological element extends 130 km along the delta front consisting of two sand ridges and two erosional channels. Three different zones within SRCS can be distinguished. The eastern initial zone stretches along delta slope and inner shelf platform southwest of the Bassac river mouth, the largest and westernmost distributary of the Mekong Delta. In the central zone SRCS covers the outer part of the subaqueous delta platform with a pronounced sand-ridge and erosional channel morphology. Cross-sections of the SRCS reveal an asymmetric shape including steeper ridge flanks facing into offshore direction. Channels incise down to 18.2 m water depth (wd) and 10.5 down the ridge top at the outer subaqueous delta platform, respectively. Towards the west the sand ridges pinch out while the two channels merge into one and form a giant erosional scour of up to 33 m wd within the subaqueous delta platform. In the western zone, the channel gets shallower and vanishes along the south-western edge of the subaqueous delta platform around Ca Mau Cape. Sediment transport from the Mekong River nourishes the sand ridges. In contrast, tide and wind-driven currents cut the erosional channels, which act also as fine-sediment conveyor from eroding headlands to the distal part of the delta front that is 200 km apart of the Bassac river mouth. SRCS in the subaqueous Mekong Delta is a relevant indicator of delta-front instability and erosion.

Window into the Caledonian orogen: Structure of the crust beneath the East Shetland platform, United Kingdom

USGS Publications Warehouse

McBride, J.H.; England, R.W.

1999-01-01

Reprocessing and interpretation of commercial and deep seismic reflection data across the East Shetland platform and its North Sea margin provide a new view of crustal subbasement structure beneath a poorly known region of the British Caledonian orogen. The East Shetland platform, east of the Great Glen strike-slip fault system, is one of the few areas of the offshore British Caledonides that remained relatively insulated from the Mesozoic and later rifting that involved much of the area around the British Isles, thus providing an "acoustic window" into the deep structure of the orogen. Interpretation of the reflection data suggests that the crust beneath the platform retains a significant amount of its original Caledonian and older architecture. The upper to middle crust is typically poorly reflective except for individual prominent dipping reflectors with complex orientations that decrease in dip with depth and merge with a lower crustal layer of high reflectivity. The three-dimensional structural orientation of the reflectors beneath the East Shetland platform is at variance with Caledonian reflector trends observed elsewhere in the Caledonian orogen (e.g., north of the Scottish mainland), emphasizing the unique tectonic character of this part of the orogen. Upper to middle crustal reflectors are interpreted as Caledonian or older thrust surfaces that were possibly reactivated by Devonian extension associated with post-Caledonian orogenic collapse. The appearance of two levels of uneven and diffractive (i.e., corrugated) reflectivity in the lower crust, best developed on east-west-oriented profiles, is characteristic of the East Shetland platform. However, a north-south-oriented profile reveals an interpreted south-vergent folded and imbricated thrust structure in the lower crust that appears to be tied to the two levels of corrugated reflectivity on the east-west profiles. A thrust-belt origin for lower crustal reflectivity would explain its corrugated appearance. Regional seismic velocity models derived from refraction data suggest that this reflectivity correlates with a continuous lower crustal layer that has an intermediate seismic velocity. The lower crustal reflectivity is determined to be older than Mesozoic age by the bending down and truncation of the two reflectivity levels at the western margin of the North Sea Viking graben by a major mantle reflector inferred to be associated with Mesozoic rifting. The results of this study are thus in contrast with orthodox interpretations of the reflective layered lower crust as being caused by mantle-derived igneous intrusion or by deformation fabrics associated with stretching in response to continental rifting.

Review of technology for Arctic offshore oil and gas recovery. Appendices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sackinger, W. M.

1980-06-06

This volume contains appendices of the following: US Geological Survey Arctic operating orders, 1979; Det Noske Vertas', rules for the design, construction and inspection of offshore technology, 1977; Alaska Oil and Gas Association, industry research projects, March 1980; Arctic Petroleum Operator's Association, industry research projects, January 1980; selected additional Arctic offshore bibliography on sea ice, icebreakers, Arctic seafloor conditions, ice-structures, frost heave and structure icing.

Some recent advances of intelligent health monitoring systems for civil infrastructures in HIT

NASA Astrophysics Data System (ADS)

Ou, Jinping

2005-06-01

The intelligent health monitoring systems more and more become a technique for ensuring the health and safety of civil infrastructures and also an important approach for research of the damage accumulation or even disaster evolving characteristics of civil infrastructures, and attracts prodigious research interests and active development interests of scientists and engineers since a great number of civil infrastructures are planning and building each year in mainland China. In this paper, some recent advances on research, development nad implementation of intelligent health monitoring systems for civil infrastructuresin mainland China, especially in Harbin Institute of Technology (HIT), P.R.China. The main contents include smart sensors such as optical fiber Bragg grating (OFBG) and polivinyllidene fluoride (PVDF) sensors, fatigue life gauges, self-sensing mortar and carbon fiber reinforced polymer (CFRP), wireless sensor networks and their implementation in practical infrastructures such as offshore platform structures, hydraulic engineering structures, large span bridges and large space structures. Finally, the relative research projects supported by the national foundation agencies of China are briefly introduced.

Damage identification of a TLP floating wind turbine by meta-heuristic algorithms

NASA Astrophysics Data System (ADS)

Ettefagh, M. M.

2015-12-01

Damage identification of the offshore floating wind turbine by vibration/dynamic signals is one of the important and new research fields in the Structural Health Monitoring (SHM). In this paper a new damage identification method is proposed based on meta-heuristic algorithms using the dynamic response of the TLP (Tension-Leg Platform) floating wind turbine structure. The Genetic Algorithms (GA), Artificial Immune System (AIS), Particle Swarm Optimization (PSO), and Artificial Bee Colony (ABC) are chosen for minimizing the object function, defined properly for damage identification purpose. In addition to studying the capability of mentioned algorithms in correctly identifying the damage, the effect of the response type on the results of identification is studied. Also, the results of proposed damage identification are investigated with considering possible uncertainties of the structure. Finally, for evaluating the proposed method in real condition, a 1/100 scaled experimental setup of TLP Floating Wind Turbine (TLPFWT) is provided in a laboratory scale and the proposed damage identification method is applied to the scaled turbine.

Whole-body concentrations of elements in three fish species from offshore oil platforms and natural areas in the Southern California Bight, USA

USGS Publications Warehouse

Love, Milton S.; Saiki, Michael K.; May, Thomas W.; Yee, Julie L.

2013-01-01

elements. Forty-two elements were excluded from statistical comparisons as they (1) consisted of major cations that were unlikely to accumulate to potentially toxic concentrations; (2) were not detected by the analytical procedures; or (3) were detected at concentrations too low to yield reliable quantitative measurements. The remaining 21 elements consisted of aluminum, arsenic, barium, cadmium, chromium, cobalt, copper, gallium, iron, lead, lithium, manganese, mercury, nickel, rubidium, selenium, strontium, tin, titanium, vanadium, and zinc. Statistical comparisons of these elements indicated that none consistently exhibited higher concentrations at oil platforms than at natural areas. However, the concentrations of copper, selenium, titanium, and vanadium in Pacific sanddab were unusual because small individuals exhibited either no differences between oil platforms and natural areas or significantly lower concentrations at oil platforms than at natural areas, whereas large individuals exhibited significantly higher concentrations at oil platforms than at natural areas.

Comparison of concentrations and profiles of polycyclic aromatic hydrocarbon metabolites in bile of fishes from offshore oil platforms and natural reefs along the California coast

USGS Publications Warehouse

Gale, Robert W.; Tanner, Michael J.; Love, Milton S.; Nishimoto, Mary M.; Schroeder, Donna M.

2012-01-01

To determine the environmental consequences of decommissioning offshore oil platforms on local and regional fish populations, contaminant loads in reproducing adults were investigated at seven platform sites and adjacent, natural sites. Specimens of three species (Pacific sanddab, Citharichthys sordidus; kelp rockfish, Sebastes atrovirens; and kelp bass, Paralabrax clathratus) residing at platforms and representing the regional background within the Santa Barbara Channel and within the San Pedro Basin were collected. Some of the most important contaminant classes related to oil operations are polycyclic aromatic hydrocarbons (PAHs) because of their potential toxicity and carcinogenicity. However, acute exposure cannot be related directly to PAH tissue concentrations because of rapid metabolism of the parent chemicals in fish; therefore, PAH metabolites in bile were measured, targeting free hydroxylated PAHs (OH-PAHs) liberated by enzymatic hydrolysis of the bound PAH glucuronides and sulfates. An ion-pairing method was developed for confirmatory analysis that targeted PAH glucuronides and sulfates. Concentrations of hydroxylated PAHs in all samples (76 fish from platforms and 64 fish from natural sites) were low, ranging from less than the limits of detection (5 to 120 nanograms per milliliter bile; 0.03 to 42 nanograms per milligram protein) to a maximum of 320 nanograms per milliliter bile (32 nanograms per milligram protein). A previously proposed dosimeter of PAH exposure in fish, 1-hydroxypyrene, was not detected at any platform site. Low concentrations of 1-hydroxypyrene were detected in 3 of 12 kelp rockfish collected from a natural reef site off Santa Barbara. The most prevalent OH-PAH, 2-hydroxyfluorene, was detected at low concentrations in seven fish of various species; of these, four were from two of the seven platform sites. The greatest concentrations of 2-hydroxyfluorene were found in three fish of various species from Platform Holly and were only about threefold above low, yet quantifiable, concentrations found in three fish from Horseshoe Reef, East Anacapa Island, and Coche Point natural sites; the mean concentrations among all sampling sites were not measurably different.

New strategies for SHM based on a multichannel wireless AE node

NASA Astrophysics Data System (ADS)

Godinez-Azcuaga, Valery; Ley, Obdulia

2014-03-01

This paper discusses the development of an Acoustic Emission (AE) wireless node and its application for SHM (Structural Health Monitoring). The instrument development was planned for applications monitoring steel and concrete bridges components. The final product, now commercially available, is a sensor node which includes multiple sensing elements, on board signal processing and analysis capabilities, signal conditioning electronics, power management circuits, wireless data transmission element and energy harvesting unit. The sensing elements are capable of functioning in both passive and active modes, while the multiple parametric inputs are available for connecting various sensor types to measure external characteristics affecting the performance of the structure under monitoring. The output of all these sensors are combined and analyzed at the node in order to minimize the data transmission rate, which consumes significant amount of power. Power management circuits are used to reduce the data collection intervals through selective data acquisition strategies and minimize the sensor node power consumption. This instrument, known as the 1284, is an excellent platform to deploy SHM in the original bridge applications, but initial prototypes has shown significant potential in monitoring composite wind turbine blades and composites mockups of Unmanned Autonomous Vehicles (UAV) components; currently we are working to extend the use of this system to fields such as coal flow, power transformer, and off-shore platform monitoring.

European developments in the application of structural austenitic and duplex stainless steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cochrane, D.J.

1995-12-31

Stainless steel is increasingly being specified for structural applications. Principally, this is due to the aesthetic appeal of the material, no need for surface protection, durability, and the growing awareness, and use, of Life Cycle Cost analysis for assessing costs over the longer term, However, use of stainless steel in the U.K. offshore oil and gas platforms for fire and blast walls, has highlighted valuable properties of stainless steel that may be unfamiliar to structural designers. It is the purpose of this paper to demonstrate these properties. Additionally, new design guidance has become available in Europe as a result ofmore » a 4 year research program into the structural use of stainless steel. The ``Design Manual for Structural Stainless Steel`` was issued by Euro Inox and the Nickel Development Institute in 1994. This new manual will be outlined in this paper together with its influence on new European Building Standards and new European material standards for structural stainless steel. Currently in preparation, these include high strength grades with significantly higher strength than structural carbon steels. Finally, this paper will address the use of stainless steel for the reinforcement of concrete structures.« less

Experimental Comparison of Dynamic Responses of a Tension Moored Floating Wind Turbine Platform with and without Spring Dampers

NASA Astrophysics Data System (ADS)

Wright, C.; O'Sullivan, K.; Murphy, J.; Pakrashi, V.

2015-07-01

The offshore wind industry is rapidly maturing and is now expanding to more extreme environments in deeper water and farther from shore. To date fixed foundation types (i.e. monopoles, jackets) have been primarily used but become uneconomical in water depths greater than 50m. Floating foundations have more complex dynamics but at the moment no design has reached commercialization, although a number of devices are being tested at prototype stage. The development of concepts is carried out through physical model testing of scaled devices such that to better understand the dynamics of the system and validate numerical models. This paper investigates the testing of a scale model of a tension moored wind turbine at two different scales and in the presence and absence of a spring damper controlling its dynamic response. The models were tested under combined wave and wind thrust loading conditions. The analysis compares the motions of the platform at different scales and structural conditions through RAO, testing a mooring spring damper for load reductions.

Multi-event behavior of El Golfo landslide (El Hierro Island, Canary Archipelago)

NASA Astrophysics Data System (ADS)

León, Ricardo; Biain, Ander; Urgeles, Roger; Somoza, Luis; Ferrer, Mercedes; García-Crespo, Jesús; Francisco Mediato, José; Galindo, Inés; Yepes, Jorge; Gimenez-Moreno, Julia

2017-04-01

Based on the re-interpretation of a vast onshore-offshore data set, a new morpho-structural characterization of the El Golfo giant landslide in the island of El Hierro (Canary Archipelago, Spain) is presented. Offshore multibeam echosounder data, chirp sub-bottom profiles, multichannel seismic reflection data and onshore information from water wells and galleries have been analyzed to determine the nature of the event. The subaerial headscarp shows a non-continuous arcuate profile formed by two nested semi-circular amphitheaters that extend offshore along a smooth chute, suggesting the occurrence of at least two large retrogressive events. Channels/gullies and escarpments developed along the submarine sector of the scar also indicate smaller-scale events and predominance of sediment bypass. At the base of submerged island, two subunits within the related submarine mass transport deposit (MTD) are identified on multichannel seismic reflection profiles confirming the multi-event nature of the landslide. The MTD, identified as a debris avalanche, has a total estimated volume of 318 km3: 84 km3 and 234 km3, for the lower and upper subunits respectively. Data from wells and galleries show abrasion platforms with beach deposits at sea-level (0 masl) formed after the landslide scar and buried by the El Golfo post-collapse infill lavas, suggesting an age at least older than 23.5-82.5 ka for the landslide. This work has been supported by the projects IGCP-640 S4SLIDE, High resolution seabed mapping EASME/EMFF/2016/005 and CTM2010-09496-E. Keywords: Submarine landslides, volcanic islands, debris avalanche, Canary Islands

Ocean Observing Public-Private Collaboration to Improve Tropical Storm and Hurricane Predictions in the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Perry, R.; Leung, P.; McCall, W.; Martin, K. M.; Howden, S. D.; Vandermeulen, R. A.; Kim, H. S. S.; Kirkpatrick, B. A.; Watson, S.; Smith, W.

2016-02-01

In 2008, Shell partnered with NOAA to explore opportunities for improving storm predictions in the Gulf of Mexico. Since, the collaboration has grown to include partners from Shell, NOAA National Data Buoy Center and National Center for Environmental Information, National Center for Environmental Prediction, University of Southern Mississippi, and the Gulf of Mexico Coastal Ocean Observing System. The partnership leverages complementary strengths of each collaborator to build a comprehensive and sustainable monitoring and data program to expand observing capacity and protect offshore assets and Gulf communities from storms and hurricanes. The program combines in situ and autonomous platforms with remote sensing and numerical modeling. Here we focus on profiling gliders and the benefits of a public-private partnership model for expanding regional ocean observing capacity. Shallow and deep gliders measure ocean temperature to derive ocean heat content (OHC), along with salinity, dissolved oxygen, fluorescence, and CDOM, in the central and eastern Gulf shelf and offshore. Since 2012, gliders have collected 4500+ vertical profiles and surveyed 5000+ nautical miles. Adaptive sampling and mission coordination with NCEP modelers provides specific datasets to assimilate into EMC's coupled HYCOM-HWRF model and 'connect-the-dots' between well-established Eulerian metocean measurements by obtaining (and validating) data between fixed stations (e.g. platform and buoy ADCPs) . Adaptive sampling combined with remote sensing provides satellite-derived OHC validation and the ability to sample productive coastal waters advected offshore by the Loop Current. Tracking coastal waters with remote sensing provides another verification of estimate Loop Current and eddy boundaries, as well as quantifying productivity and analyzing water quality on the Gulf coast, shelf break and offshore. Incorporating gliders demonstrates their value as tools to better protect offshore oil and gas assets and the greater Gulf coast communities from storms and hurricanes. Data collected under the collaboration, along with deployment of gliders, will have long-term benefits in helping to understand the ecological and environmental health of the Gulf by monitoring real-time annual and seasonal physical variability.

Advances in ice mechanics - 1987

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, J.S.; Hallam, S.D.; Maatanen, M.

1987-01-01

This book presents the papers given at a symposium on the interaction of icebergs with offshore platforms. Topics considered at the symposium included advances in ice mechanics in the United Kingdom, ice mechanics in Finland, recent advances in ice mechanics in Canada, advances in sea ice mechanics in the USA, foundations, monitoring, hazards, risk assessment, and deformation.

30 CFR 250.203 - Where can wells be located under an EP, DPP, or DOCD?

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL... that can be economically drilled for proper reservoir management; (e) Location of drilling units and platforms; (f) Extent and thickness of the reservoir; (g) Geologic and other reservoir characteristics; (h...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This paper reports on Amoco's Yombo offshore oil field development on Marine I permit which is well under way with installation of decks on two wellhead platforms. Initial production from the field has begun at about 6,000 bopd. With production estimated to be 40,000 bopd by early 1992, it will bring Congo's total production to more than 200,000 bopd.

Developing AN Emergency Response Model for Offshore Oil Spill Disaster Management Using Spatial Decision Support System (sdss)

NASA Astrophysics Data System (ADS)

Balogun, Abdul-Lateef; Matori, Abdul-Nasir; Wong Toh Kiak, Kelvin

2018-04-01

Environmental resources face severe risks during offshore oil spill disasters and Geographic Information System (GIS) Environmental Sensitivity Index (ESI) maps are increasingly being used as response tools to minimize the huge impacts of these spills. However, ESI maps are generally unable to independently harmonize the diverse preferences of the multiple stakeholders' involved in the response process, causing rancour and delay in response time. This paper's Spatial Decision Support System (SDSS) utilizes the Analytic Hierarchy Process (AHP) model to perform tradeoffs in determining the most significant resources to be secured considering the limited resources and time available to perform the response operation. The AHP approach is used to aggregate the diverse preferences of the stakeholders and reach a consensus. These preferences, represented as priority weights, are incorporated in a GIS platform to generate Environmental sensitivity risk (ESR) maps. The ESR maps provide a common operational platform and consistent situational awareness for the multiple parties involved in the emergency response operation thereby minimizing discord among the response teams and saving the most valuable resources.

An evaluation of oil spill responses for offshore oil production projects in Newfoundland and Labrador, Canada: Implications for seabird conservation.

PubMed

Fraser, Gail S; Racine, Vincent

2016-06-15

Seabirds are vulnerable to oil pollution, particularly in cold-water regions. We investigated the response of small spills (<7.95m(3)) at offshore production platforms in Newfoundland, a region recognized for seabird diversity and abundance. In three environmental assessments for oil production operations Environment Canada requested monitoring and mitigation of small spills potentially impacting seabird populations; suggestions supported by two independent reviews. An industry spill response plan states that operators would collect systematic observations on spills and deploy countermeasures where possible. Operators' spill reports were obtained under an Access to Information request. There were 220 daytime spills with sheens (out of 381 spills; 1997-2010). Of these, six reported time to oil dispersion and eleven the presence or absence of seabirds. Industry self-reporting has not permitted an evaluation of the impact of chronic oil spills on seabirds. We recommend that independent observers be placed on platforms to systematically collect data on spills and seabirds. Copyright © 2016 Elsevier Ltd. All rights reserved.

Coastal Erosion in a Coral Reef Island, Taiping Island, South China Sea

NASA Astrophysics Data System (ADS)

Su, S.; Ma, G.; Liang, M.; Chu, J.

2011-12-01

Reef flats surrounding islands are known to dissipate much offshore wave energy, and thereby protect beaches from erosion. Taiping Island, the largest coral reef islands of the Spratly Islands in the South China Sea, has been observed the shorelines erosion on the southwest coast over past decades. It is recognized that wave and current processes across coral reefs affect reef-island development and morphology. A number of studies suggest effects of climate changes, sea-level rise and storm-intensity increase, determine the magnitude of wave energy on the reef platform and will likely intensify the erosion. The topographical change in the local region, the southwest reef flat was dredged a channel for navigation, may be a significant factor in influencing current characteristics. Numerical modeling is used to describe both hydrodynamics and sediment dynamics because there are no field measurements available around the reef flat. Field observations off the island conducted in August 2004 and November 2005 provides offshore wave characteristics of the predominant wind seasons. Numerical simulations perform the spatial and temporal variation of waves and current patterns and coastal erosion potential on the reef platform.

An Aeroelastic Perspective of Floating Offshore Wind Turbine Wake Formation and Instability

NASA Astrophysics Data System (ADS)

Rodriguez, Steven N.; Jaworski, Justin W.

2015-11-01

The wake formation and wake stability of floating offshore wind turbines are investigated from an aeroelastic perspective. The aeroelastic model is composed of the Sebastian-Lackner free-vortex wake aerodynamic model coupled to the nonlinear Hodges-Dowell beam equations, which are extended to include the effects of blade profile asymmetry, higher-order torsional effects, and kinetic energy components associated with periodic rigid-body motions of floating platforms. Rigid-body platform motions are also assigned to the aerodynamic model as varying inflow conditions to emulate operational rotor-wake interactions. Careful attention is given to the wake formation within operational states where the ratio of inflow velocity to induced velocity is over 50%. These states are most susceptible to aerodynamic instabilities, and provide a range of states about which a wake stability analysis can be performed. In addition, the stability analysis used for the numerical framework is implemented into a standalone free-vortex wake aerodynamic model. Both aeroelastic and standalone aerodynamic results are compared to evaluate the level of impact that flexible blades have on the wake formation and wake stability.

Geologic evolution and sequence stratigraphy of the offshore Pelotas Basin, southeast Brazil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abreu, V.S.

1996-01-01

The Brazilian marginal basins have been studied since the beginning of the 70s. At least nine large basins are distributed along the entire Eastern continental margin. The sedimentary infill of these basins consists of lower Cretaceous (continental/lacustrine) rift section underlying marine upper Cretaceous (carbonate platforms) and marine upper Cretaceous/Tertiary sections, corresponding to the drift phase. The sedimentary deposits are a direct result of the Jurassic to lower Cretaceous break-up of the Pangea. This study will focus on the geologic evolution and sequence stratigraphic analysis of the Pelotas basin (offshore), located in the Southeast portion of the Brazilian continental margin betweenmore » 28[degrees] and 34[degrees] S, covering approximately 50,000 Km[sup 2]. During the early Cretaceous, when the break-up of the continent began in the south, thick basaltic layers were deposited in the Pelotas basin. These basalts form a thick and broad wedge of dipping seaward reflections interpreted as a transitional crust. During Albian to Turonian times, due to thermal subsidence, an extensive clastic/carbonate platform was developed, in an early drift stage. The sedimentation from the upper Cretaceous to Tertiary was characterized by a predominance of siliciclastics in the southeast margin, marking an accentuate deepening of the basin, showing several cycles related to eustatic fluctuations. Studies have addressed the problems of hydrocarbon exploration in deep water setting within a sequence stratigraphic framework. Thus Pelotas basin can provide a useful analogue for exploration efforts worldwide in offshore passive margins.« less

Geologic evolution and sequence stratigraphy of the offshore Pelotas Basin, southeast Brazil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abreu, V.S.

1996-12-31

The Brazilian marginal basins have been studied since the beginning of the 70s. At least nine large basins are distributed along the entire Eastern continental margin. The sedimentary infill of these basins consists of lower Cretaceous (continental/lacustrine) rift section underlying marine upper Cretaceous (carbonate platforms) and marine upper Cretaceous/Tertiary sections, corresponding to the drift phase. The sedimentary deposits are a direct result of the Jurassic to lower Cretaceous break-up of the Pangea. This study will focus on the geologic evolution and sequence stratigraphic analysis of the Pelotas basin (offshore), located in the Southeast portion of the Brazilian continental margin betweenmore » 28{degrees} and 34{degrees} S, covering approximately 50,000 Km{sup 2}. During the early Cretaceous, when the break-up of the continent began in the south, thick basaltic layers were deposited in the Pelotas basin. These basalts form a thick and broad wedge of dipping seaward reflections interpreted as a transitional crust. During Albian to Turonian times, due to thermal subsidence, an extensive clastic/carbonate platform was developed, in an early drift stage. The sedimentation from the upper Cretaceous to Tertiary was characterized by a predominance of siliciclastics in the southeast margin, marking an accentuate deepening of the basin, showing several cycles related to eustatic fluctuations. Studies have addressed the problems of hydrocarbon exploration in deep water setting within a sequence stratigraphic framework. Thus Pelotas basin can provide a useful analogue for exploration efforts worldwide in offshore passive margins.« less

Unsteady aerodynamic analysis for offshore floating wind turbines under different wind conditions.

PubMed

Xu, B F; Wang, T G; Yuan, Y; Cao, J F

2015-02-28

A free-vortex wake (FVW) model is developed in this paper to analyse the unsteady aerodynamic performance of offshore floating wind turbines. A time-marching algorithm of third-order accuracy is applied in the FVW model. Owing to the complex floating platform motions, the blade inflow conditions and the positions of initial points of vortex filaments, which are different from the fixed wind turbine, are modified in the implemented model. A three-dimensional rotational effect model and a dynamic stall model are coupled into the FVW model to improve the aerodynamic performance prediction in the unsteady conditions. The effects of floating platform motions in the simulation model are validated by comparison between calculation and experiment for a small-scale rigid test wind turbine coupled with a floating tension leg platform (TLP). The dynamic inflow effect carried by the FVW method itself is confirmed and the results agree well with the experimental data of a pitching transient on another test turbine. Also, the flapping moment at the blade root in yaw on the same test turbine is calculated and compares well with the experimental data. Then, the aerodynamic performance is simulated in a yawed condition of steady wind and in an unyawed condition of turbulent wind, respectively, for a large-scale wind turbine coupled with the floating TLP motions, demonstrating obvious differences in rotor performance and blade loading from the fixed wind turbine. The non-dimensional magnitudes of loading changes due to the floating platform motions decrease from the blade root to the blade tip. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Unsteady aerodynamic analysis for offshore floating wind turbines under different wind conditions

PubMed Central

Xu, B. F.; Wang, T. G.; Yuan, Y.; Cao, J. F.

2015-01-01

A free-vortex wake (FVW) model is developed in this paper to analyse the unsteady aerodynamic performance of offshore floating wind turbines. A time-marching algorithm of third-order accuracy is applied in the FVW model. Owing to the complex floating platform motions, the blade inflow conditions and the positions of initial points of vortex filaments, which are different from the fixed wind turbine, are modified in the implemented model. A three-dimensional rotational effect model and a dynamic stall model are coupled into the FVW model to improve the aerodynamic performance prediction in the unsteady conditions. The effects of floating platform motions in the simulation model are validated by comparison between calculation and experiment for a small-scale rigid test wind turbine coupled with a floating tension leg platform (TLP). The dynamic inflow effect carried by the FVW method itself is confirmed and the results agree well with the experimental data of a pitching transient on another test turbine. Also, the flapping moment at the blade root in yaw on the same test turbine is calculated and compares well with the experimental data. Then, the aerodynamic performance is simulated in a yawed condition of steady wind and in an unyawed condition of turbulent wind, respectively, for a large-scale wind turbine coupled with the floating TLP motions, demonstrating obvious differences in rotor performance and blade loading from the fixed wind turbine. The non-dimensional magnitudes of loading changes due to the floating platform motions decrease from the blade root to the blade tip. PMID:25583859

Investigation of the Hosgri Fault, offshore Southern California, Point Sal to Point Conception

USGS Publications Warehouse

Payne, C.M.; Swanson, O.E.; Schell, B.A.

1979-01-01

A high-resolution seismic reflection survey of the inner continental shelf between Point Sal and Point Conception has revealed faults that displace post-Wisconsin strata (less than 17,000-20,000 years). These faults are the Hosgri fault, the Offshore Lompoc fault, and smaller unnamed faults. Faults trending offshore from the adjacent shoreline such as the Pezzoni, Lions Head, Honda, and Pacifico faults, do not show post-Wisconsin activity. The Hosgri fault trends directly toward the coastline between Purisima Point and Point Arguello where it appears to merge with folds and smaller faults in the western Transverse Ranges. This trend of offshore structures toward the Point Arguello-Point Conception area is consistent with a hypothesis that the regional structural fabric of the southern California Coast Ranges and its adjacent offshore area merge with the Transverse Ranges.

Towers for Offshore Wind Turbines

NASA Astrophysics Data System (ADS)

Kurian, V. J.; Narayanan, S. P.; Ganapathy, C.

2010-06-01

Increasing energy demand coupled with pollution free production of energy has found a viable solution in wind energy. Land based windmills have been utilized for power generation for more than two thousand years. In modern times wind generated power has become popular in many countries. Offshore wind turbines are being used in a number of countries to tap the energy from wind over the oceans and convert to electric energy. The advantages of offshore wind turbines as compared to land are that offshore winds flow at higher speed than onshore winds and the more available space. In some land based settings, for better efficiency, turbines are separated as much as 10 rotor diameters from each other. In offshore applications where only two wind directions are likely to predominate, the distances between the turbines arranged in a line can be shortened to as little as two or four rotor diameters. Today, more than a dozen offshore European wind facilities with turbine ratings of 450 kw to 3.6 MW exist offshore in very shallow waters of 5 to 12 m. Compared to onshore wind turbines, offshore wind turbines are bigger and the tower height in offshore are in the range of 60 to 80 m. The water depths in oceans where offshore turbines can be located are within 30 m. However as the distance from land increases, the costs of building and maintaining the turbines and transmitting the power back to shore also increase sharply. The objective of this paper is to review the parameters of design for the maximum efficiency of offshore wind turbines and to develop types offshore towers to support the wind turbines. The methodology of design of offshore towers to support the wind turbine would be given and the environmental loads for the design of the towers would be calculated for specific cases. The marine corrosion on the towers and the methods to control the corrosion also would be briefly presented. As the wind speeds tend to increase with distance from the shore, turbines build father offshore will be able to capture more wind energy. Currently two types of towers are considered. Cylindrical tubular structures and truss type structures. But truss type structures have less weight and flexibility in design. The construction of the offshore towers to harness the wind energy is also presented. The results will include the calculation of wind and wave forces on the tower and the design details for the tower.

40 CFR 125.138 - As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

Code of Federal Regulations, 2013 CFR

2013-07-01

... offshore oil and gas extraction facility, must I keep records and report? 125.138 Section 125.138... Intake Structures for New Offshore Oil and Gas Extraction Facilities Under Section 316(b) of the Act § 125.138 As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

40 CFR 125.138 - As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

Code of Federal Regulations, 2014 CFR

2014-07-01

... offshore oil and gas extraction facility, must I keep records and report? 125.138 Section 125.138... Intake Structures for New Offshore Oil and Gas Extraction Facilities Under Section 316(b) of the Act § 125.138 As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

40 CFR 125.138 - As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

Code of Federal Regulations, 2010 CFR

2010-07-01

... offshore oil and gas extraction facility, must I keep records and report? 125.138 Section 125.138... Intake Structures for New Offshore Oil and Gas Extraction Facilities Under Section 316(b) of the Act § 125.138 As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

40 CFR 125.138 - As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

Code of Federal Regulations, 2012 CFR

2012-07-01

... offshore oil and gas extraction facility, must I keep records and report? 125.138 Section 125.138... Intake Structures for New Offshore Oil and Gas Extraction Facilities Under Section 316(b) of the Act § 125.138 As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

40 CFR 125.138 - As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

Code of Federal Regulations, 2011 CFR

2011-07-01

... offshore oil and gas extraction facility, must I keep records and report? 125.138 Section 125.138... Intake Structures for New Offshore Oil and Gas Extraction Facilities Under Section 316(b) of the Act § 125.138 As an owner or operator of a new offshore oil and gas extraction facility, must I keep records...

Proceedings of the Conference Arctic '85; Civil Engineering in the Artic offshore

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bennett, F.L.; Machemehl, J.L.

1985-01-01

Topics of the 1985 Conference included: Arctic construction, Arctic foundation, Arctic structures, and ocean effects. Arctic terminals and coastal offshore bases, protecting the Arctic environment, and probabilistic methods in Arctic offshore engineering were also discussed. Ice mechanics, marine pipelines in the Arctic, and the role of universities in training civil engineers for Arctic offshore development were highlighted. Sessions on remote sensing, surveying, and mapping were included, and offshore installations in the Bering Sea were discussed. Another topic of discussion was research in Civil Engineering for development of the Arctic offshore. The overall thrust of the conference was the application ofmore » Arctic offshore engineering principles and research in the field of oil and gas exploration and exploitation activity.« less

Monitoring of corrosion damage using high-frequency guided ultrasonic waves

NASA Astrophysics Data System (ADS)

Chew, D.; Fromme, P.

2014-03-01

Due to adverse environmental conditions corrosion can develop during the life cycle of industrial structures, e.g., offshore oil platforms, ships, and desalination plants. Both pitting corrosion and generalized corrosion leading to wall thickness loss can cause the degradation of the integrity and load bearing capacity of the structure. Structural health monitoring of corrosion damage in difficult to access areas can in principle be achieved using high frequency guided waves propagating along the structure from accessible areas. Using standard ultrasonic transducers with single sided access to the structure, high frequency guided wave modes were generated that penetrate through the complete thickness of the structure. Wall thickness reduction was induced using accelerated corrosion in a salt water bath. The corrosion damage was monitored based on the effect on the wave propagation and interference of the different modes. The change in the wave interference was quantified based on an analysis in the frequency domain (Fourier transform) and was found to match well with theoretical predictions for the wall thickness loss. High frequency guided waves have the potential for corrosion damage monitoring at critical and difficult to access locations from a stand-off distance.

Monitoring of corrosion damage using high-frequency guided ultrasonic waves

NASA Astrophysics Data System (ADS)

Chew, D.; Fromme, P.

2015-03-01

Due to adverse environmental conditions corrosion can develop during the life cycle of industrial structures, e.g., offshore oil platforms, ships, and desalination plants. Both pitting corrosion and generalized corrosion leading to wall thickness loss can cause the degradation of the integrity and load bearing capacity of the structure. Structural health monitoring of corrosion damage in difficult to access areas can in principle be achieved using high frequency guided waves propagating along the structure from accessible areas. Using standard ultrasonic transducers with single sided access to the structure, high frequency guided wave modes were generated that penetrate through the complete thickness of the structure. Wall thickness reduction was induced using accelerated corrosion in a salt water bath. The corrosion damage was monitored based on the effect on the wave propagation and interference of the different modes. The change in the wave interference was quantified based on an analysis in the frequency domain (Fourier transform) and was found to match well with theoretical predictions for the wall thickness loss. High frequency guided waves have the potential for corrosion damage monitoring at critical and difficult to access locations from a stand-off distance.

On the predominance of unstable atmospheric conditions in the marine boundary layer offshore of the U.S. northeastern coast

DOE PAGES

Archer, Cristina L.; Colle, Brian A.; Veron, Dana L.; ...

2016-07-18

The marine boundary layer of the northeastern U.S. is studied with focus on wind speed, atmospheric stability, and turbulent kinetic energy (TKE), the three most relevant properties in the context of offshore wind power development. Two long-term observational data sets are analyzed. The first one consists of multilevel meteorological variables measured up to 60 m during 2003–2011 at the offshore Cape Wind tower, located near the center of the Nantucket Sound. The second data set comes from the 2013–2014 IMPOWR campaign (Improving the Modeling and Prediction of Offshore Wind Resources), in which wind and wave data were collected with newmore » instruments on the Cape Wind platform, in addition to meteorological data measured during 19 flight missions offshore of New York, Connecticut, Rhode Island, and Massachusetts. It is found that, in this region: (1) the offshore wind resource is remarkable, with monthly average wind speeds at 60 m exceeding 7 m s -1 all year round, highest winds in winter (10.1 m s -1) and lowest in summer (7.1 m s -1), and a distinct diurnal modulation, especially in summer; (2) the marine boundary layer is predominantly unstable (61% unstable vs. 21% neutral vs. 18% stable), meaning that mixing is strong, heat fluxes are positive, and the wind speed profile is often nonlogarithmic (~40% of the time); and (3) the shape of the wind speed profile (log versus nonlog) is an effective qualitative proxy for atmospheric stability, whereas TKE alone is not.« less

On the predominance of unstable atmospheric conditions in the marine boundary layer offshore of the U.S. northeastern coast

DOE Office of Scientific and Technical Information (OSTI.GOV)

Archer, Cristina L.; Colle, Brian A.; Veron, Dana L.

The marine boundary layer of the northeastern U.S. is studied with focus on wind speed, atmospheric stability, and turbulent kinetic energy (TKE), the three most relevant properties in the context of offshore wind power development. Two long-term observational data sets are analyzed. The first one consists of multilevel meteorological variables measured up to 60 m during 2003–2011 at the offshore Cape Wind tower, located near the center of the Nantucket Sound. The second data set comes from the 2013–2014 IMPOWR campaign (Improving the Modeling and Prediction of Offshore Wind Resources), in which wind and wave data were collected with newmore » instruments on the Cape Wind platform, in addition to meteorological data measured during 19 flight missions offshore of New York, Connecticut, Rhode Island, and Massachusetts. It is found that, in this region: (1) the offshore wind resource is remarkable, with monthly average wind speeds at 60 m exceeding 7 m s -1 all year round, highest winds in winter (10.1 m s -1) and lowest in summer (7.1 m s -1), and a distinct diurnal modulation, especially in summer; (2) the marine boundary layer is predominantly unstable (61% unstable vs. 21% neutral vs. 18% stable), meaning that mixing is strong, heat fluxes are positive, and the wind speed profile is often nonlogarithmic (~40% of the time); and (3) the shape of the wind speed profile (log versus nonlog) is an effective qualitative proxy for atmospheric stability, whereas TKE alone is not.« less

Hurricane shuts down gulf activity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koen, A.D.

1992-08-31

This paper reports that producers in the Gulf of Mexico and plant operators in South Louisiana last week were checking for damage wrought by Hurricane Andrew. In its wake Andrew left evacuated rigs and platforms in the gulf and shuttered plants across a wide swath of the Gulf Coast. Operations were beginning to return to normal late last week. Not all gulf operators, especially in the central gulf, expected to return to offshore facilities. And even producers able to book helicopters did not expect to be able to fully assess damage to all offshore installations before the weekend. MMS officialsmore » in Washington estimated that 37,500 offshore workers were evacuated from 700 oil and gas installations on the gulf's Outer Continental Shelf. Gulf oil and gas wells account for about 800,000 b/d of oil and one fourth of total U.S. gas production. MMS was awaiting an assessment of hurricane damage before estimating how soon and how much gulf oil and gas production would be restored.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knott, D.

Northwest Europe`s offshore operators have boosted their oil and gas production dramatically in recent years, and while the area is now mature, a steady stream of developments continues. In the boom days of the late 1970s and 1980s, a typical North Sea installation was a large platform, which occasionally a new pipeline or, more commonly, a tie-in to the area`s massive export grids. These days, now that technical developments have enabled operators to justify developments of smaller, once uneconomic, discoveries, it is pointless to talk of a typical offshore development. Northwest Europe`s offshore operators have learned that it is worthwhilemore » to rack their brains for the most economic development concepts. This creativity is reflected in recent development plans. While operators are now snatching up the small accumulations in and around the mature North Sea producing fields, they are also seeking develop frontier regions. The paper discusses development activities in UK, Ireland, Denmark and Greenland, and Norway in gas, oil, and gas condensate deposits.« less

From Apollo to Cognac

NASA Technical Reports Server (NTRS)

1980-01-01

Shell Oil Company started oil and gas production from a new offshore platform called Cognac located in the Gulf of Mexico. It is the world's tallest oil platform, slightly taller than the Empire State Building. The highly complex job of installing Cognac's support "jacket" under water more than a thousand feet deep was directed from a barge-based control center. To enable crews to practice in advance difficult tasks never before accomplished, Honeywell, adapting NASA's Apollo technology, developed a system for simulating the various underwater operations. In training sessions, displays and controls reacted exactly as they would in real operation.

Aeroelastic Stability Investigations for Large-scale Vertical Axis Wind Turbines

NASA Astrophysics Data System (ADS)

Owens, B. C.; Griffith, D. T.

2014-06-01

The availability of offshore wind resources in coastal regions, along with a high concentration of load centers in these areas, makes offshore wind energy an attractive opportunity for clean renewable electricity production. High infrastructure costs such as the offshore support structure and operation and maintenance costs for offshore wind technology, however, are significant obstacles that need to be overcome to make offshore wind a more cost-effective option. A vertical-axis wind turbine (VAWT) rotor configuration offers a potential transformative technology solution that significantly lowers cost of energy for offshore wind due to its inherent advantages for the offshore market. However, several potential challenges exist for VAWTs and this paper addresses one of them with an initial investigation of dynamic aeroelastic stability for large-scale, multi-megawatt VAWTs. The aeroelastic formulation and solution method from the BLade Aeroelastic STability Tool (BLAST) for HAWT blades was employed to extend the analysis capability of a newly developed structural dynamics design tool for VAWTs. This investigation considers the effect of configuration geometry, material system choice, and number of blades on the aeroelastic stability of a VAWT, and provides an initial scoping for potential aeroelastic instabilities in large-scale VAWT designs.

Dynamic modal estimation using instrumental variables

NASA Technical Reports Server (NTRS)

Salzwedel, H.

1980-01-01

A method to determine the modes of dynamical systems is described. The inputs and outputs of a system are Fourier transformed and averaged to reduce the error level. An instrumental variable method that estimates modal parameters from multiple correlations between responses of single input, multiple output systems is applied to estimate aircraft, spacecraft, and off-shore platform modal parameters.

Direct-current converter for gas-discharge lamps

NASA Technical Reports Server (NTRS)

Lutus, P.

1980-01-01

Metal/halide and similar gas-discharge lamps are powered from low-voltage dc source using small efficient converter. Converter is useful whenever 60-cycle ac power is not available or where space and weight allocations are limited. Possible applications are offshore platforms, mobile homes, and emergency lighting. Design innovations give supply high reliability and efficiency up to 75 percent.

Dynamic response signatures of a scaled model platform for floating wind turbines in an ocean wave basin.

PubMed

Jaksic, V; O'Shea, R; Cahill, P; Murphy, J; Mandic, D P; Pakrashi, V

2015-02-28

Understanding of dynamic behaviour of offshore wind floating substructures is extremely important in relation to design, operation, maintenance and management of floating wind farms. This paper presents assessment of nonlinear signatures of dynamic responses of a scaled tension-leg platform (TLP) in a wave tank exposed to different regular wave conditions and sea states characterized by the Bretschneider, the Pierson-Moskowitz and the JONSWAP spectra. Dynamic responses of the TLP were monitored at different locations using load cells, a camera-based motion recognition system and a laser Doppler vibrometer. The analysis of variability of the TLP responses and statistical quantification of their linearity or nonlinearity, as non-destructive means of structural monitoring from the output-only condition, remains a challenging problem. In this study, the delay vector variance (DVV) method is used to statistically study the degree of nonlinearity of measured response signals from a TLP. DVV is observed to create a marker estimating the degree to which a change in signal nonlinearity reflects real-time behaviour of the structure and also to establish the sensitivity of the instruments employed to these changes. The findings can be helpful in establishing monitoring strategies and control strategies for undesirable levels or types of dynamic response and can help to better estimate changes in system characteristics over the life cycle of the structure. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Assessing storm events for energy meteorology: using media and scientific reports to track a North Sea autumn storm.

NASA Astrophysics Data System (ADS)

Kettle, Anthony

2016-04-01

Important issues for energy meteorology are to assess meteorological conditions for normal operating conditions and extreme events for the ultimate limit state of engineering structures. For the offshore environment in northwest Europe, energy meteorology encompasses weather conditions relevant for petroleum production infrastructure and also the new field of offshore wind energy production. Autumn and winter storms are an important issue for offshore operations in the North Sea. The weather in this region is considered as challenging for extreme meteorological events as the Gulf of Mexico with its attendant hurricane risk. The rise of the Internet and proliferation of digital recording devices has placed a much greater amount of information in the public domain than was available to national meteorological agencies even 20 years ago. This contribution looks at reports of meteorology and infrastructure damage from a storm in the autumn of 2006 to trace the spatial and temporal record of meteorological events. Media reports give key information to assess the events of the storm. The storm passed over northern Europe between Oct.31-Nov. 2, 2006, and press reports from the time indicate that its most important feature was a high surge that inundated coastal areas. Sections of the Dutch and German North Sea coast were affected, and there was record flooding in Denmark and East Germany in the southern Baltic Sea. Extreme wind gusts were also reported that were strong enough to damage roofs and trees, and there was even tornado recorded near the Dutch-German border. Offshore, there were a series of damage reports from ship and platforms that were linked with sea state, and reports of rogue waves were explicitly mentioned. Many regional government authorities published summaries of geophysical information related to the storm, and these form part of a regular series of online winter storm reports that started as a public service about 15 years ago. Depending on the issuing authority, these reports include wind speed and atmospheric pressure for a number of stations. However, there is also important ancillary information that includes satellite images, weather radar pictures, sea state recordings, tide gauge records, and coastal surveys. When collated together, the literature survey gives good view of events related to the autumn storm. The key information from media reports is backed up by quantitative numbers from the scientific literature. For energy meteorology in the offshore environment, there is an outline of extreme wave events that may be important to help define the ultimate limit state of engineering structures and the return periods of extreme waves. While this contribution focusses on events from an old storm in the autumn of 2006, more severe regional storms have occurred since then, and the scientific literature indicates that these may be linked with climate warming. Literature surveys may help to fully define extreme meteorological conditions offshore and benefit different branches of the energy industry in Europe.

Getting offshoring right.

PubMed

Aron, Ravi; Singh, Jitendra V

2005-12-01

The prospect of offshoring and outsourcing business processes has captured the imagination of CEOs everywhere. In the past five years, a rising number of companies in North America and Europe have experimented with this strategy, hoping to reduce costs and gain strategic advantage. But many businesses have had mixed results. According to several studies, half the organizations that have shifted processes offshore have failed to generate the expected financial benefits. What's more, many of them have faced employee resistance and consumer dissatisfaction. Clearly, companies have to rethink how they formulate their offshoring strategies. A three-part methodology can help. First, companies need to prioritize their processes, ranking each based on two criteria: the value it creates for customers and the degree to which the company can capture some of that value. Companies will want to keep their core (highest-priority) processes in-house and consider outsourcing their commodity (low-priority) processes; critical (moderate-priority) processes are up for debate and must be considered carefully. Second, businesses should analyze all the risks that accompany offshoring and look systematically at their critical and commodity processes in terms of operational risk (the risk that processes won't operate smoothly after being offshored) and structural risk (the risk that relationships with service providers may not work as expected). Finally, companies should determine possible locations for their offshore efforts, as well as the organizational forms--such as captive centers and joint ventures--that those efforts might take. They can do so by examining each process's operational and structural risks side by side. This article outlines the tools that will help companies choose the right processes to offshore. It also describes a new organizational structure called the extended organization, in which companies specify the quality of services they want and work alongside providers to get that quality.

Feasibility of Floating Platform Systems for Wind Turbines: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Musial, W.; Butterfield, S.; Boone, A.

This paper provides a general technical description of several types of floating platforms for wind turbines. Platform topologies are classified into multiple- or single-turbine floaters and by mooring method. Platforms using catenary mooring systems are contrasted to vertical mooring systems and the advantages and disadvantages are discussed. Specific anchor types are described in detail. A rough cost comparison is performed for two different platform architectures using a generic 5-MW wind turbine. One platform is a Dutch study of a tri-floater platform using a catenary mooring system, and the other is a mono-column tension-leg platform developed at the National Renewable Energymore » Laboratory. Cost estimates showed that single unit production cost is $7.1 M for the Dutch tri-floater, and $6.5 M for the NREL TLP concept. However, value engineering, multiple unit series production, and platform/turbine system optimization can lower the unit platform costs to $4.26 M and $2.88 M, respectively, with significant potential to reduce cost further with system optimization. These foundation costs are within the range necessary to bring the cost of energy down to the DOE target range of $0.05/kWh for large-scale deployment of offshore floating wind turbines.« less

[Offshore work and the work of nurses on board: an integrative review].

PubMed

Antoniolli, Silvana Aline Cordeiro; Emmel, Suzel Vaz; Ferreira, Gímerson Erick; Paz, Potiguara de Oliveira; Kaiser, Dagmar Elaine

2015-08-01

To know the production of theoretical approaches on issues related to offshore work and the work of offshore nurses. Integrative literature review conducted in the databases of LILACS, BDENF, MEDLINE, SciELO and Index PSI. We selected 33 studies published in national and international journals between 1997 and 2014. The thematic analysis corpus resulted in four central themes: offshore work environment; amid work adversities, an escape; structuring of offshore health and safety services; in search of safe practices. This study contributes to the offshore work of nurses in relation to the nature of work, acting amid adversities and the restless search for safe practices in the open sea.

Application of two passive strategies on the load mitigation of large offshore wind turbines

NASA Astrophysics Data System (ADS)

Shirzadeh, Rasoul; Kühn, Martin

2016-09-01

This study presents the numerical results of two passive strategies to reduce the support structure loads of a large offshore wind turbine. In the first approach, an omnidirectional tuned mass damper is designed and implemented in the tower top to alleviate the structural vibrations. In the second approach, a viscous fluid damper model which is diagonally attached to the tower at two points is developed. Aeroelastic simulations are performed for the offshore 10MW INNWIND.EU reference wind turbine mounted on a jacket structure. Lifetime damage equivalent loads are evaluated at the tower base and compared with those for the reference wind turbine. The results show that the integrated design can extend the lifetime of the support structure.

Long-term Bat Monitoring on Islands, Offshore Structures, and Coastal Sites in the Gulf of Maine, mid-Atlantic, and Great Lakes—Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peterson, Trevor; Pelletier, Steve; Giovanni, Matt

This report summarizes results of a long-term regional acoustic survey of bat activity at remote islands, offshore structures, and coastal sites in the Gulf of Maine, Great Lakes, and mid-Atlantic coast.

Waste management practices in the Gulf of Suez - Egypt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghzaly, S.M.; Binegar, J.S.

1996-12-31

The Gulf of Suez Petroleum Company (GUPCO) is the largest offshore oil producing company in Egypt. GUPCO currently produces 400,000 BOPD from over 350 wells supported by 87 offshore producing platforms. As a leader of the Egyptian petroleum industry, GUPCO established within its strategies and goals a separate category covering safety, health and Protection of the environment. This step was recognized and emphasized the importance of GUPCO`s role in protecting the Egyptian environment while producing oil and natural gas. This paper discusses the existing waste management practices of the Gulf of Suez Petroleum Company which were put into place tomore » protect the Egyptian environment in the Gulf of Suez-Egypt and GUPCO`s associated operations.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Childers, M.; Barnes, J.

The phased field development of the Lion and Panthere fields, offshore the Ivory Coast, includes a small floating production, storage, and offloading (FPSO) tanker with minimal processing capability as an early oil production system (EPS). For the long-term production scheme, the FPSO will be replaced by a converted jack up mobile offshore production system (MOPS) with full process equipment. The development also includes guyed-caisson well platforms, pipeline export for natural gas to fuel an onshore power plant, and a floating storage and offloading (FSO) tanker for oil export. Pipeline export for oil is a future possibility. This array of innovativemore » strategies and techniques seldom has been brought together in a single project. The paper describes the development plan, early oil, jack up MOPS, and transport and installation.« less

Smart Novel Semi-Active Tuned Mass Damper for Fixed-Bottom and Floating Offshore Wind (Paper)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodriguez Tsouroukdissian, Arturo; Lackner, Mathew; Cross-Whiter, John

The intention of this paper is to present the results of a novel smart semi-active tuned mass damper (SA-TMD), which mitigates unwanted loads for both fixed-bottom and floating offshore wind systems. The paper will focus on the most challenging water depths for both fixed-bottom and floating systems. A close to 38m Monopile and 55m Tension Leg Platform (TLP) will be considered. A technical development and trade-off analysis will be presented comparing the new system with existing passive non-linear TMD (N-TMD) technology and semi-active. TheSATMD works passively and activates itself with low power source under unwanted dynamic loading in less thanmore » 60msec. It is composed of both variable stiffness and damping elements coupled to a central pendulum mass. The analysis has been done numerically in both FAST(NREL) and Orcaflex (Orcina), and integrated in the Wind Turbine system employing CAD/CAE. The results of this work will pave the way for experimental testing to complete the technology qualification process. The load reductions under extreme and fatigue cases reach up significant levels at tower base, consequently reducing LCOE for fixed-bottom to floating wind solutions. The nacelle acceleration is reduced substantially under severe random wind and sea states, reducing the risks of failure of electromechanical components and blades at the rotor nacelle assembly. The SA-TMD system isa new technology that has not been applied previously in wind solutions. Structural damping devices aim to increase offshore wind turbine system robustness and reliability, which eases multiple substructures installations and global stability.« less

Collating science-based evidence to inform public opinion on the environmental effects of marine drilling platforms in the Mediterranean Sea.

PubMed

Mangano, M C; Sarà, G

2017-03-01

The use of rigorous methodologies to assess environmental, social and health impacts of specific interventions is crucial to disentangle the various components of environmental questions and to inform public opinion. The power of systematic maps relies on the capacity to summarise and organise the areas or relationships most studied, and to highlight key gaps in the evidence base. The recent Italian technical referendum (2016) - a public consultation inviting people to express their opinion by voting to change the rules on the length of licence duration and the decommissioning of offshore oil and gas platform drilling licences - inspired the creation of a systematic map of evidence to scope and quantify the effects of off-shore extraction platforms on Mediterranean marine ecosystems. The map was aimed as a useful model to standardise a "minimal informational threshold", which can inform public opinion at the beginning of any public consultation. Produced by synthesising scientific information, the map represents a reliable layer for any future sustainable strategy in the Mediterranean basin by: (i) providing a summary of the effects of marine gas and oil platforms on the Mediterranean marine ecosystem, (ii) describing the best known affected components on which the biggest monitoring efforts have been focused, and (iii) strengthening the science-policy nexus by offering a credible, salient and legitimate knowledge baseline to both public opinion and decision-makers. The map exercise highlights the knowledge gaps that need filling and taking into due consideration before future transnational and cross-border monitoring and management plans and activities can be addressed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Structural Geology and Microstructures of Wrangel Island, Arctic Russia

NASA Astrophysics Data System (ADS)

Miller, E. L.; Dumitru, T. A.; Seward, G.

2010-12-01

Wrangel Island is a unique exposure of Neoproterozoic basement and upper Paleozoic and Mesozoic cover. Its geology is critical for testing the continuity of stratigraphic units and structures across the Chukchi Sea from Alaska to Russia, for constraining paleogeography and plate reconstructions of the Arctic and for evaluating the hydrocarbon potential of this offshore region. The Paleozoic stratigraphy of Wrangel correlates to the offshore Hannah Trough, Alaska, but its thick section of Triassic turbidites has no counterpart in Alaska (Miller et al., 2010, AAPG; Sherwood et al., 2002, GSA Spec. Paper 360). Wrangel Island lies on a regional structural high along strike of the offshore Herald Arch and Chukchi Platform, Alaska. To the north, the deep North Chukchi Basin, bound by ~E-NE trending, north-dipping normal faults, is inferred to contain up to 12 km of Beaufortian and Brookian (Late Jurassic to Tertiary) sediments in addition to Paleozoic strata (Dinkelman et al., 2008). To the south, ~E-W trending faults bound the Longa Basin that separates Wrangel from Chukotka and lies along strike of the early Tertiary Hope Basin. Wrangel Island was interpreted to represent a north-vergent Mesozoic to Tertiary fold and thrust belt traced offshore by seismic reflection to the Herald Arch and then to the Lisburne Hills and the Brooks Range foreland fold and thrust belt, (e.g. Kos’ko et al., 1993). However, deformation of Wrangel Island rocks differs significantly from typical foreland fold-thrust structures. Both cover and basement rocks have strong penetrative metamorphic fabrics. Foliation strikes E-W and dips ~40° S, with a pronounced N-S trending elongation or stretching lineation. Aspect ratios of stretched pebbles are ~ 5:1:.2 to 10:1:.1. The foliation is axial planar to tight/isoclinal folds at all scales and these also involve the basement-sediment contact. 25 oriented thin-sections of feldspathic sandstones and grits were examined for sense of shear and the fabrics in quartz-rich domains studied by electron back-scatter diffraction (EBSD). These studies indicate that systematic sense of shear indicators/asymmetric fabrics (top to the N versus top to the S) are uncommon and if present, not pervasive or consistent. EBSD studies of quartz fabrics together with growth of metamorphic biotite at deepest structural levels suggest temperatures as high as 450°C for deformation, with subsequent cooling at shallower levels of the crust to preserve the observed quartz microstructures. Cooling of rocks through 100°C based on apatite fission track ages occurred by ~ 95 Ma, providing a minimum age for deformation. The penetrative fabrics and large strains are more similar to high strain fabrics developed during extension such as those developed along the south flank of the Brooks Range, on the Seward Peninsula, and mainland Chukotka. It is inferred that structures on Wrangel Island formed during an episode of high heat flow and N-S ductile stretching of the crust, an interpretation compatible with the age constraints on the fabrics and the structural position of Wrangel between two large normal-fault bound basins.

Potential use of offshore marine structures in rebuilding an overfished rockfish species, bocaccio (Sebastes paucispinis)

USGS Publications Warehouse

Love, M.S.; Schroeder, D.M.; Lenarz, W.; MacCall, A.; Bull, A.S.; Thorsteinson, L.

2006-01-01

Although bocaccio (Sebastes paucispinis) was an economically important rockfish species along the west coast of North America, overfishing has reduced the stock to about 7.4% of its former unfished population. In 2003, using a manned research submersible, we conducted fish surveys around eight oil and gas platforms off southern California as part of an assessment of the potential value of these structures as fish habitat. From these surveys, we estimated that there was a minimum of 430,000 juvenile bocaccio at these eight structures. We determined this number to be about 20% of the average number of juvenile bocaccio that survive annually for the geographic range of the species. When these juveniles become adults, they will contribute about one percent (0.8%) of the additional amount of fish needed to rebuild the Pacific Coast population. By comparison, juvenile bocaccio recruitment to nearshore natural nursery grounds, as determined through regional scuba surveys, was low in the same year. This research demonstrates that a relatively small amount of artificial nursery habitat may be quite valuable in rebuilding an overfished species.

Geology of the Attaka oil field, East Kalimantan, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schwartz, C.M.; Laughbaum, G.H. Jr.; Samsu, B.S.

1973-11-01

The Attaka field is the first commercial offshore oil field to be discovered in Kalimantan, Indonesia. After its discovery in 1970 and the drilling of confirmation wells during 1970 and 1971, a development program involving 50 wells from 6 platforms was begun. The field is 12 miles off shore from the E. Kalimantan coast in 200 ft of water. Areal and vertical closures of the Attaka structure are 26 sq miles and 600 ft, respectively, and the areal extent of oil accumulation is some 9.8 sq miles. The Attaka structure is located in the Tertiary Kutei Basin which contains earlymore » Tertiary to Quaternary sediments, and the oil in the Attaka field is in numerous deltaic sands deposited during a late Miocene advance of the ancestral Mahakam River delta. Seismic velocity and well velocity survey data indicate the presence of a low velocity region more or less coincident with the limits of oil and gas accumulation on the crest of the Attaka structure. Gravity of the Attaka oil ranges from 35' to 43' API and its sulfur content is 0.1% by wt.« less

40 CFR 125.139 - As the Director, what must I do to comply with the requirements of this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... DISCHARGE ELIMINATION SYSTEM Requirements Applicable to Cooling Water Intake Structures for New Offshore Oil... the initial permit application from the owner or operator of a new offshore oil and gas extraction... offshore oil and gas extraction facility. In addition, the Director must review materials to determine...

40 CFR 125.139 - As the Director, what must I do to comply with the requirements of this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... DISCHARGE ELIMINATION SYSTEM Requirements Applicable to Cooling Water Intake Structures for New Offshore Oil... the initial permit application from the owner or operator of a new offshore oil and gas extraction... offshore oil and gas extraction facility. In addition, the Director must review materials to determine...

40 CFR 125.139 - As the Director, what must I do to comply with the requirements of this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... DISCHARGE ELIMINATION SYSTEM Requirements Applicable to Cooling Water Intake Structures for New Offshore Oil... the initial permit application from the owner or operator of a new offshore oil and gas extraction... offshore oil and gas extraction facility. In addition, the Director must review materials to determine...

40 CFR 125.139 - As the Director, what must I do to comply with the requirements of this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... DISCHARGE ELIMINATION SYSTEM Requirements Applicable to Cooling Water Intake Structures for New Offshore Oil... the initial permit application from the owner or operator of a new offshore oil and gas extraction... offshore oil and gas extraction facility. In addition, the Director must review materials to determine...

40 CFR 125.139 - As the Director, what must I do to comply with the requirements of this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... DISCHARGE ELIMINATION SYSTEM Requirements Applicable to Cooling Water Intake Structures for New Offshore Oil... the initial permit application from the owner or operator of a new offshore oil and gas extraction... offshore oil and gas extraction facility. In addition, the Director must review materials to determine...

A Network for Standardized Ocean Color Validation Measurements

NASA Technical Reports Server (NTRS)

Zibordi, Giuseppe; Holben, Brent; Hooker, Stanford; Melin, Frederic; Berthon, Jean-Francois; Slutsker, Ilya; Giles, David; Vandemark, Doug; Feng, Hui; Rutledge, Ken;

Performance of hydraulic fracturing and matrix acidizing in horizontal wellbores -- Offshore Qatar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, M.G.R.; Pongratz, R.

Considerable debate in the Middle East has centered upon what was previously felt to be two separate methods of enhancing revenues and daily production; hydraulic fracturing and horizontal drilling. In an effort to maximize return on investment, these two issues have been successfully combined in other areas of the world. In order to establish the suitability of this technology in this area, two horizontal wells with over 3,050m (10,000ft) of lateral section were drilled into the Cretaceous Kharaib formation, overlying the North Field, Offshore Qatar. A massive stimulation program was performed in order to evaluate the most feasible stimulation methodmore » from both a technical and economical perspective for further field development considerations.Three propped hydraulic fracturing treatments were performed using 183, 500kg (403, 700lb) of 20/40 mesh sand, and seventeen acid matrix treatments placing over 3,217,250l (850,000gals) of HCL into the lateral sections of both wells. This paper describes the performance, operation and logistical support required to complete this offshore operation with join a minimal time frame. The use of a mobile offshore jack-up platform, whereby a land based fracturing spread was placed onto the deck of a converted drilling rig is described.« less

Update on GPS-Acoustics Measurements on the Continental Slope of the Cascadia Subduction Zone

NASA Astrophysics Data System (ADS)

Chadwell, C. D.

2017-12-01

Land-based GPS measurements suggest the megathrust is locked offshore along the Cascadia Subduction Zone. However, land-based data alone lack geometric resolution to constrain the how the slip is distributed. GPS-Acoustic measurements can provide these constraints, but using traditional GPS-Acoustic approaches employing a ship is costly. Wave Gliders, a wave- and solar-powered, remotely-piloted sea surface platform, provide a low cost method for collecting GPS-A data. We have adapted GPS-Acoustic technology to the Wave Glider and in 2016 began annual measurements at three sites in the Cascadia Subduction Zone (CSZ). Here, we review positioning results collected during summer 2017 at two sites on the continental slope of the Cascadia Subduction Zone: One site is approximately 45 NM offshore central Oregon and the other approximately 50 NM offshore central Washington State. A third site is approximately 90 NM offshore central Oregon on the incoming Juan de Fuca plate. We will report on initial results of the GPS-A data collection and operational experiences of the missions in 2016 and 2017. Wave Glider based GPS-A measurement have the potential to significantly increase the number and frequency of measurements of strain accumulation in Cascadia Subduction Zone and elsewhere.

Light, Compact Pumper for Harbor Fires

NASA Technical Reports Server (NTRS)

Burns, R. A.

1983-01-01

Report describes development of new transportable water-pumping unit for fire-fighting. Compact, self-contained unit provides fire protection at coastal and inland ports and is lighter than standard firetruck pumper of same capacity. Used to fight fires in harbors, cities, forests, refineries, chemical plants, and offshore drilling platforms. Other possible applications include cleaning up oilspills, pumping out ships, and flood control pumping.

30 CFR 250.108 - What requirements must I follow for cranes and other material-handling equipment?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What requirements must I follow for cranes and... follow for cranes and other material-handling equipment? (a) All cranes installed on fixed platforms must... Maintenance of Offshore Cranes (API RP 2D), incorporated by reference as specified in 30 CFR 250.198. (b) All...

Interference evaluation between manifold and wet Christmas tree CP systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brasil, S.L.D.C.; Baptista, W.

2000-05-01

Offshore production wells are controlled by valves installed in the marine soil, called wet Christmas trees (WCTs). A manifold receives the production of several wells and transports it to the platform. The manifold is cathodically protected by Al anodes and the WCT by Zn anodes. A computer simulation was carried out to evaluate the interference between the equipment cathodic protection systems.

An Assessment of Wave and Wind Data for Use in Design of Tension Leg Platforms - U.S. Offshore Areas.

DTIC Science & Technology

1984-07-01

level crossing rate equations first developed by Rice are commonly employed, reference 4. If one assumes that the wave height variance spectrum is...wave photo was kindly furnished by Mr. Dillard Hammett of SEDCO, Inc. : "The photo was taken in November, 1982. The location was the Ekofisk Field

NREL/University of Delaware Offshore Wind R&D Collaboration: Cooperative Research and Development Final Report, CRADA Number CRD-10-393

DOE Office of Scientific and Technical Information (OSTI.GOV)

Musial, Walt

2015-11-12

Specifically, the work under this CRADA includes, but is not limited to, the development of test procedures for an offshore test site in Delaware waters; testing of installed offshore wind turbines; performance monitoring of those turbines; and a program of research and development on offshore wind turbine blades, components, coatings, foundations, installation and construction of bottom-fixed structures, environmental impacts, policies, and more generally on means to enhance the reliability, facilitate permitting, and reduce costs for offshore wind turbines. This work will be conducted both at NREL's National Wind Technology Center and participant facilities, as well as the established offshore windmore » test sites.« less

Novel Atmospheric and Sea State Modeling in Ocean Energy Applications

NASA Astrophysics Data System (ADS)

Kallos, George; Galanis, George; Kalogeri, Christina; Larsen, Xiaoli Guo

2013-04-01

The rapidly increasing use of renewable energy sources poses new challenges for the research and technological community today. The integration of the, usually, highly variable wind and wave energy amounts into the general grid, the optimization of energy transition and the forecast of extreme values that could lead to instabilities and failures of the system can be listed among them. In the present work, novel methodologies based on state of the art numerical wind/wave simulation systems and advanced statistical techniques addressing such type of problems are discussed. In particular, extremely high resolution modeling systems simulating the atmospheric and sea state conditions with spatial resolution of 100 meters or less and temporal discretization of a few seconds are utilized in order to simulate in the most detailed way the combined wind-wave energy potential at offshore sites. In addition, a statistical analysis based on a variety of mean and variation measures as well as univariate and bivariate probability distributions is used for the estimation of the variability of the power potential revealing the advantages of the use of combined forms of energy by offshore platforms able to produce wind and wave power simultaneously. The estimation and prediction of extreme wind/wave conditions - a critical issue both for site assessment and infrastructure maintenance - is also studied by means of the 50-year return period over areas with increased power potential. This work has been carried out within the framework of the FP7 project MARINA Platform (http://www.marina-platform.info/index.aspx).

Conceptual design study: Cold water pipe systems for self-mounted OTEC powerplants

NASA Astrophysics Data System (ADS)

1981-02-01

The conceptual design and installation aspects of cold water pipes (CWP) systems for shelf mounted OTEC power plants in Puerto Rico and Hawaii are considered. The CWP systems using Fiberglass Reinforced Plastic (FRP) and steel were designed; the FRP, can be controlled by varying the core thickness; and steel is used as a structural material in offshore applications. A marine railway approach was chosen for installation of the CWP. Two methods for pulling the track for the railway down the pipe fairway to its final location are presented. The track is permanently fastened to the sloping seabed with piles installed by a remotely controlled cart that rides on the track itself. Both the marine railway and the shelf mounted platform that houses the OTEC power plant require an anodic or equivalent corrosion protection system.

Petroleum geology of the major producing basins of Algeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Attar, A.; Chaouch, A.

1988-08-01

The South Atlas flexure divides Algeria into two contrasting geologic provinces: (1) the Saharan Atlas and offshore region in the north, both of which are part of the Mediterranean basin, and (2) the Saharan platform on the south, part of the North African craton. The limits of the various sedimentary basins on the Saharan platform are tied to late Paleozoic (Hercynian) crustal reactivation. Comparable structurally controlled basins in northern Algeria are the products of Mesozoic-Recent tectonism. The spatial and temporal distribution of hydrocarbons in the Algerian Sahara can be understood in terms of the geologic evolution of the region. Analysismore » of areas of proven hydrocarbon reserves permits the following generalizations. (1) There is a concentration of oil and gas fields northeast of a northwest-southeast-trending line connecting Hassi R'Mel with In Amenas. Production is also established in the Sbaa basin and in northern Algeria, where recent discoveries have been made in, respectively, upper Paleozoic and Mesozoic reservoirs. (2) Hydrocarbon are present throughout the entire sedimentary column, but major production currently is restricted to the lower Paleozoic (Cambrian-Ordovician and Lower Devonian) and Triassic reservoirs.« less

High-throughput metabarcoding of eukaryotic diversity for environmental monitoring of offshore oil-drilling activities.

PubMed

Lanzén, Anders; Lekang, Katrine; Jonassen, Inge; Thompson, Eric M; Troedsson, Christofer

2016-09-01

As global exploitation of available resources increases, operations extend towards sensitive and previously protected ecosystems. It is important to monitor such areas in order to detect, understand and remediate environmental responses to stressors. The natural heterogeneity and complexity of communities means that accurate monitoring requires high resolution, both temporally and spatially, as well as more complete assessments of taxa. Increased resolution and taxonomic coverage is economically challenging using current microscopy-based monitoring practices. Alternatively, DNA sequencing-based methods have been suggested for cost-efficient monitoring, offering additional insights into ecosystem function and disturbance. Here, we applied DNA metabarcoding of eukaryotic communities in marine sediments, in areas of offshore drilling on the Norwegian continental shelf. Forty-five samples, collected from seven drilling sites in the Troll/Oseberg region, were assessed, using the small subunit ribosomal RNA gene as a taxonomic marker. In agreement with results based on classical morphology-based monitoring, we were able to identify changes in sediment communities surrounding oil platforms. In addition to overall changes in community structure, we identified several potential indicator taxa, responding to pollutants associated with drilling fluids. These included the metazoan orders Macrodasyida, Macrostomida and Ceriantharia, as well as several ciliates and other protist taxa, typically not targeted by environmental monitoring programmes. Analysis of a co-occurrence network to study the distribution of taxa across samples provided a framework for better understanding the impact of anthropogenic activities on the benthic food web, generating novel, testable hypotheses of trophic interactions structuring benthic communities. © 2016 The Authors. Molecular Ecology Published by John Wiley & Sons Ltd.

Borehole Breakout Derived Constraints on Stress Regimes in the Santa Barbara Channel, Offshore Southern California

NASA Astrophysics Data System (ADS)

Pritchard, E. H.; Persaud, P.; Stock, J. M.

2017-12-01

The Santa Barbara Channel is an E-W trending marine basin that serves as the southern extension of the Western Transverse Ranges block. Several active, E-W trending en echelon fault systems exist beneath the Channel with both N and S dips. These control a series of tight, asymmetric anticlinal folds along the North Channel and Mid-Channel regions. Although controversial, recent models have suggested that these systems are capable of producing large magnitude, tsunamigenic earthquakes. Not controversial, however, is the fact that further knowledge of the stress regime related to these systems would greatly contribute to our understanding of a potential rupture along them. In this study, oriented 4-arm caliper well log data obtained from industry are used to determine the orientations of stress induced shear failures along well bore walls, called borehole breakouts, beneath two offshore drill platforms in the Santa Barbara Channel. Analysis of breakout orientations along 18 differently oriented, highly deviated wells allows for constraint of the current in situ stress regime beneath each of the platforms. The best-fit stress regime can then be used to inform the nature of slip along nearby faults, many of which are blind and display no surface indications of slip. At the Holly platform, located roughly 19 km west of Santa Barbara, and proximate to the Pitas Point, North Channel, and Red Mountain fault systems, lower hemisphere polar projections of breakout orientations in deviated well sections indicate a mainly thrust faulting stress regime, although a strike-slip component is not currently excluded. At the Gail platform, located midway between Ventura and Santa Cruz Island, and proximate to the Western Deep Fault, polar projections of breakouts indicate that a predominantly thrust faulting stress regime also exists beneath this platform. However, a few inconsistencies in the breakout orientations at each platform suggest variability in the stress regime, leading to the hypothesis that the stress field beneath these regions may change with depth, from a shallow degenerate-like thrust faulting stress state, with the horizontal principal stresses roughly equal in magnitude yet greater than the vertical principal stress (SH = Sh > Sv), to a deeper, less degenerate regime.

Sea Spray and Icing in the Emerging Open Water of the Arctic Ocean

DTIC Science & Technology

2015-06-12

concentrations of wind-generated sea spray and the resulting spray icing on offshore structures, such as wind turbines and exploration, drilling , and...We anticipate that structures placed in shallow water—wind turbines, drilling rigs, or man-made production islands, for instance—will, therefore...and the severity of sea spray icing on fixed offshore structures. We will use existing information on the relationship of the spray concentration

Design for perception management system on offshore reef based on integrated management

NASA Astrophysics Data System (ADS)

Peng, Li; Qiankun, Wang

2017-06-01

According to an analysis of actual monitoring demands using integrated management and information technology, a quad monitoring system is proposed to provide intelligent perception of offshore reefs, including indoor building environments, architectural structures, and facilities and perimeter integrity. This will strengthen the ability to analyse and evaluate offshore reef operation and health, promoting efficiency in decision making.

Geologic assessment of undiscovered oil and gas resources—Lower Cretaceous Albian to Upper Cretaceous Cenomanian carbonate rocks of the Fredericksburg and Washita Groups, United States Gulf of Mexico Coastal Plain and State Waters

USGS Publications Warehouse

Swanson, Sharon M.; Enomoto, Catherine B.; Dennen, Kristin O.; Valentine, Brett J.; Cahan, Steven M.

2017-02-10

In 2010, the U.S. Geological Survey (USGS) assessed Lower Cretaceous Albian to Upper Cretaceous Cenomanian carbonate rocks of the Fredericksburg and Washita Groups and their equivalent units for technically recoverable, undiscovered hydrocarbon resources underlying onshore lands and State Waters of the Gulf Coast region of the United States. This assessment was based on a geologic model that incorporates the Upper Jurassic-Cretaceous-Tertiary Composite Total Petroleum System (TPS) of the Gulf of Mexico basin; the TPS was defined previously by the USGS assessment team in the assessment of undiscovered hydrocarbon resources in Tertiary strata of the Gulf Coast region in 2007. One conventional assessment unit (AU), which extends from south Texas to the Florida panhandle, was defined: the Fredericksburg-Buda Carbonate Platform-Reef Gas and Oil AU. The assessed stratigraphic interval includes the Edwards Limestone of the Fredericksburg Group and the Georgetown and Buda Limestones of the Washita Group. The following factors were evaluated to define the AU and estimate oil and gas resources: potential source rocks, hydrocarbon migration, reservoir porosity and permeability, traps and seals, structural features, paleoenvironments (back-reef lagoon, reef, and fore-reef environments), and the potential for water washing of hydrocarbons near outcrop areas.In Texas and Louisiana, the downdip boundary of the AU was defined as a line that extends 10 miles downdip of the Lower Cretaceous shelf margin to include potential reef-talus hydrocarbon reservoirs. In Mississippi, Alabama, and the panhandle area of Florida, where the Lower Cretaceous shelf margin extends offshore, the downdip boundary was defined by the offshore boundary of State Waters. Updip boundaries of the AU were drawn based on the updip extent of carbonate rocks within the assessed interval, the presence of basin-margin fault zones, and the presence of producing wells. Other factors evaluated were the middle Cenomanian sea-level fall and erosion that removed large portions of platform and platform-margin carbonate sediments in the Washita Group of central Louisiana. The production history of discovered reservoirs and well data within the AU were examined to estimate the number and size of undiscovered oil and gas reservoirs within the AU. Using the USGS National Oil and Gas Assessment resource assessment methodology, mean volumes of 40 million barrels of oil, 622 billion cubic feet of gas, and 14 million barrels of natural gas liquids are the estimated technically recoverable undiscovered resources for the Fredericksburg-Buda Carbonate Platform-Reef Gas and Oil AU.

Investigation on the Effect of Initial Welding Imperfection on Fatigue strength of Tubular Member by FEM

NASA Astrophysics Data System (ADS)

Chang, Kyong-Ho; Shin, Wang Sub; Nguyen Van Vuong, Do; Lee, Chin Hyeong

2018-04-01

Steel tube structure is used for steel structure such as offshore platform, bridges and so on. Also, all circular members of tubular structures are mainly connected by welding. When the steel tubular structures are subjected to repeated loading, not only the load carrying capacity is reduced but also fatigue cracks may develop at the joint part of steel tubular members which are connected by welding. Carrying out welding, welding initial imperfection such as welding deformation and residual stress are inevitably generated at weld part. It was well known that the effect of welding residual and welding deformation on fatigue strength. However, It’s not clear which affects fatigue strength more. However, it’s difficult to clear the effect on fatigue strength by experiment. To clarify these effect, fatigue analysis was carried out by FEM which is based on continuum damage mechanics. On the other hand, coupled three-dimensional non-steady heat conduction analysis, and the thermal elastic-plastic analysis was carried out to reproduce the initial weld state of tubular member. From the result, not only the fatigue strength of welded tubular member but also the fatigue life could be found by FEM fatigue analysis.

Study on optimized decision-making model of offshore wind power projects investment

NASA Astrophysics Data System (ADS)

Zhao, Tian; Yang, Shangdong; Gao, Guowei; Ma, Li

2018-02-01

China’s offshore wind energy is of great potential and plays an important role in promoting China’s energy structure adjustment. However, the current development of offshore wind power in China is inadequate, and is much less developed than that of onshore wind power. On the basis of considering all kinds of risks faced by offshore wind power development, an optimized model of offshore wind power investment decision is established in this paper by proposing the risk-benefit assessment method. To prove the practicability of this method in improving the selection of wind power projects, python programming is used to simulate the investment analysis of a large number of projects. Therefore, the paper is dedicated to provide decision-making support for the sound development of offshore wind power industry.

40 CFR 125.136 - As an owner or operator of a new offshore oil and gas extraction facility, what must I collect...

Code of Federal Regulations, 2011 CFR

2011-07-01

... stresses on the source waterbody. (B) Evaluation of potential cooling water intake structure effects. This... (CONTINUED) WATER PROGRAMS CRITERIA AND STANDARDS FOR THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Requirements Applicable to Cooling Water Intake Structures for New Offshore Oil and Gas Extraction Facilities...

40 CFR 125.136 - As an owner or operator of a new offshore oil and gas extraction facility, what must I collect...

Code of Federal Regulations, 2010 CFR

2010-07-01

... stresses on the source waterbody. (B) Evaluation of potential cooling water intake structure effects. This... (CONTINUED) WATER PROGRAMS CRITERIA AND STANDARDS FOR THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM Requirements Applicable to Cooling Water Intake Structures for New Offshore Oil and Gas Extraction Facilities...

Subsea pipeline isolation systems: Reliability and costs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Masheder, R.R.

1995-12-31

On the night of 6/7 July 1988 a major oil production platform known as Piper Alpha in the UK sector of the North Sea was destroyed by explosion and fire, with the loss of 167 lives. This led to the appointment of Lord Cullen, a senior Scottish Judge, to hold a Public Inquiry into the Piper Alpha Disaster. The Cullen Enquiry Report consisting of 23 chapters set out in 2 volumes, was published on 12 November 1990. One of the important conclusions drawn by Lord Cullen resulted in a recommendation for studies to be conducted to consider ways of improvingmore » the reliability and reducing the costs of SSIVs (Subsea Isolation Valves) so that it is more often reasonably practicable to install them. To address the Cullen recommendations, a joint industry study was conducted by UKOOA (United Kingdom Offshore Operators Association) and the HSE/OSD (Health and Safety Executive Offshore Safety Division) in conjunction with independent consultants. The results of the studies and the conclusions drawn by UKOOA Pipeline Valve Group and the HSE Offshore Safety Division are presented in this paper.« less

Simulation of a weather radar display for over-water airborne radar approaches

NASA Technical Reports Server (NTRS)

Clary, G. R.

1983-01-01

Airborne radar approach (ARA) concepts are being investigated as a part of NASA's Rotorcraft All-Weather Operations Research Program on advanced guidance and navigation methods. This research is being conducted using both piloted simulations and flight test evaluations. For the piloted simulations, a mathematical model of the airborne radar was developed for over-water ARAs to offshore platforms. This simulated flight scenario requires radar simulation of point targets, such as oil rigs and ships, distributed sea clutter, and transponder beacon replies. Radar theory, weather radar characteristics, and empirical data derived from in-flight radar photographs are combined to model a civil weather/mapping radar typical of those used in offshore rotorcraft operations. The resulting radar simulation is realistic and provides the needed simulation capability for ongoing ARA research.

Offshore finfish aquaculture in the United States: An examination of federal laws that could be used to address environmental and occupational public health risks.

PubMed

Fry, Jillian P; Love, David C; Shukla, Arunima; Lee, Ryan M

2014-11-19

Half of the world's edible seafood comes from aquaculture, and the United States (US) government is working to develop an offshore finfish aquaculture industry in federal waters. To date, US aquaculture has largely been regulated at the state level, and creating an offshore aquaculture industry will require the development of a new regulatory structure. Some aquaculture practices involve hazardous working conditions and the use of veterinary drugs, agrochemicals, and questionable farming methods, which could raise environmental and occupational public health concerns if these methods are employed in the offshore finfish industry in the US. This policy analysis aims to inform public health professionals and other stakeholders in the policy debate regarding how offshore finfish aquaculture should be regulated in the US to protect human health; previous policy analyses on this topic have focused on environmental impacts. We identified 20 federal laws related to offshore finfish aquaculture, including 11 that are relevant to preventing, controlling, or monitoring potential public health risks. Given the novelty of the industry in the US, myriad relevant laws, and jurisdictional issues in an offshore setting, federal agencies need to work collaboratively and transparently to ensure that a comprehensive and functional regulatory structure is established that addresses the potential public health risks associated with this type of food production.

Offshore Finfish Aquaculture in the United States: An Examination of Federal Laws That Could be Used to Address Environmental and Occupational Public Health Risks

PubMed Central

Fry, Jillian P.; Love, David C.; Shukla, Arunima; Lee, Ryan M.

2014-01-01

Half of the world’s edible seafood comes from aquaculture, and the United States (US) government is working to develop an offshore finfish aquaculture industry in federal waters. To date, US aquaculture has largely been regulated at the state level, and creating an offshore aquaculture industry will require the development of a new regulatory structure. Some aquaculture practices involve hazardous working conditions and the use of veterinary drugs, agrochemicals, and questionable farming methods, which could raise environmental and occupational public health concerns if these methods are employed in the offshore finfish industry in the US. This policy analysis aims to inform public health professionals and other stakeholders in the policy debate regarding how offshore finfish aquaculture should be regulated in the US to protect human health; previous policy analyses on this topic have focused on environmental impacts. We identified 20 federal laws related to offshore finfish aquaculture, including 11 that are relevant to preventing, controlling, or monitoring potential public health risks. Given the novelty of the industry in the US, myriad relevant laws, and jurisdictional issues in an offshore setting, federal agencies need to work collaboratively and transparently to ensure that a comprehensive and functional regulatory structure is established that addresses the potential public health risks associated with this type of food production. PMID:25415208

3-D Simulation of Earthquakes on the Cascadia Megathrust: Key Parameters and Constraints from Offshore Structure and Seismicity

NASA Astrophysics Data System (ADS)

Wirth, E. A.; Frankel, A. D.; Vidale, J. E.; Stone, I.; Nasser, M.; Stephenson, W. J.

2017-12-01

The Cascadia subduction zone has a long history of M8 to M9 earthquakes, inferred from coastal subsidence, tsunami records, and submarine landslides. These megathrust earthquakes occur mostly offshore, and an improved characterization of the megathrust is critical for accurate seismic hazard assessment in the Pacific Northwest. We run numerical simulations of 50 magnitude 9 earthquake rupture scenarios on the Cascadia megathrust, using a 3-D velocity model based on geologic constraints and regional seismicity, as well as active and passive source seismic studies. We identify key parameters that control the intensity of ground shaking and resulting seismic hazard. Variations in the down-dip limit of rupture (e.g., extending rupture to the top of the non-volcanic tremor zone, compared to a completely offshore rupture) result in a 2-3x difference in peak ground acceleration (PGA) for the inland city of Seattle, Washington. Comparisons of our simulations to paleoseismic data suggest that rupture extending to the 1 cm/yr locking contour (i.e., mostly offshore) provides the best fit to estimates of coastal subsidence during previous Cascadia earthquakes, but further constraints on the down-dip limit from microseismicity, offshore geodetics, and paleoseismic evidence are needed. Similarly, our simulations demonstrate that coastal communities experience a four-fold increase in PGA depending upon their proximity to strong-motion-generating areas (i.e., high strength asperities) on the deeper portions of the megathrust. An improved understanding of the structure and rheology of the plate interface and accretionary wedge, and better detection of offshore seismicity, may allow us to forecast locations of these asperities during a future Cascadia earthquake. In addition to these parameters, the seismic velocity and attenuation structure offshore also strongly affects the resulting ground shaking. This work outlines the range of plausible ground motions from an M9 Cascadia earthquake, and highlights the importance of offshore studies for constraining critical parameters and seismic hazard in the Pacific Northwest.

What can wave energy learn from offshore oil and gas?

PubMed

Jefferys, E R

2012-01-28

This title may appear rather presumptuous in the light of the progress made by the leading wave energy devices. However, there may still be some useful lessons to be learnt from current 'offshore' practice, and there are certainly some awful warnings from the past. Wave energy devices and the marine structures used in oil and gas exploration as well as production share a common environment and both are subject to wave, wind and current loads, which may be evaluated with well-validated, albeit imperfect, tools. Both types of structure can be designed, analysed and fabricated using similar tools and technologies. They fulfil very different missions and are subject to different economic and performance requirements; hence 'offshore' design tools must be used appropriately in wave energy project and system design, and 'offshore' cost data should be adapted for 'wave' applications. This article reviews the similarities and differences between the fields and highlights the differing economic environments; offshore structures are typically a small to moderate component of field development cost, while wave power devices will dominate overall system cost. The typical 'offshore' design process is summarized and issues such as reliability-based design and design of not normally manned structures are addressed. Lessons learned from poor design in the past are discussed to highlight areas where care is needed, and wave energy-specific design areas are reviewed. Opportunities for innovation and optimization in wave energy project and device design are discussed; wave energy projects must ultimately compete on a level playing field with other routes to low CO₂ energy and/or energy efficiency. This article is a personal viewpoint and not an expression of a ConocoPhillips position.

Oil and Water Don't Mix: The Gulf Coast Oil Disaster as a Preschool Social Studies Lesson

ERIC Educational Resources Information Center

Kruse, Tricia

2010-01-01

On April 20, 2010, an offshore oil-drilling platform exploded, spilling millions of gallons of oil into the gulf. From Louisiana to the Gulf Coast of Florida the effects are being felt by fisherman, shrimpers, dive charters, and other hardworking folks who depend on the water for their livelihood. But there is another population in these coastal…

Real-time simulation of an airborne radar for overwater approaches

NASA Technical Reports Server (NTRS)

Karmarkar, J.; Clark, D.

1982-01-01

Software developed to provide a real time simulation of an airborne radar for overwater approaches to oil rig platforms is documented. The simulation is used to study advanced concepts for enhancement of airborne radar approaches (ARA) in order to reduce crew workload, improve approach tracking precision, and reduce weather minimums. ARA's are currently used for offshore helicopter operations to and from oil rigs.

78 FR 38031 - Application for Final Commitment for a Long-Term Loan or Financial Guarantee in Excess of $100...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-25

... Petroquimica Basica. Description of Items Being Exported: Drilling rigs, platform rentals, compressors, oil... U.S. goods and services from U.S. small businesses to be used in its oil and gas projects. Brief non...'s on- and off-shore oil and gas exploration and production areas. To the extent that Ex-Im Bank is...

Meals on Wheels? A Decade of Megafaunal Visual and Acoustic Observations from Offshore Oil & Gas Rigs and Platforms in the North and Irish Seas.

PubMed

Todd, Victoria Louise Georgia; Warley, Jane Clare; Todd, Ian Boyer

2016-01-01

A decade of visual and acoustic detections of marine megafauna around offshore Oil & Gas (O&G) installations in the North and Irish Seas are presented. Marine megafauna activity was monitored visually and acoustically by Joint Nature Conservation Committee (JNCC) qualified and experienced Marine Mammal Observers (MMO) and Passive Acoustic Monitoring (PAM) Operators respectively, with real-time towed PAM in combination with industry standard software, PAMGuard. Monitoring was performed during routine O&G industrial operations for underwater noise mitigation purposes, and to ensure adherence to regulatory guidelines. Incidental sightings by off-effort MMOs and installation crew were also reported. Visual and acoustic monitoring spanned 55 non-consecutive days between 2004 and 2014. A total of 47 marine mammal sightings were recorded by MMOs on dedicated watch, and 10 incidental sightings of marine megafauna were reported over 10 years. Species included: harbour porpoise (Phocoena phocoena), Atlantic white-sided dolphin (Lagenorhynchus acutus), white beaked dolphin (Lagenorhynchus albirostris), common dolphin (Delphinus delphis), minke whale (Balaenoptera acutorostrata), common seal (Phoca vitulina), grey seal (Halichoerus grypus) and, basking shark (Cetorhinus maximus). Passive Acoustic Monitoring was conducted on two occasions in 2014; 160 PAM hours over 12 days recorded a total of 308 individual clicks identified as harbour porpoises. These appear to be the first such acoustic detections obtained from a North Sea drilling rig whilst using a typically configured hydrophone array designed for towing in combination with real-time PAMGuard software. This study provides evidence that marine megafauna are present around mobile and stationary offshore O&G installations during routine operational activities. On this basis, Environmental Impact Assessments (EIAs) for decommissioning O&G platforms should be carried-out on a case-by-case basis, and must include provisions for hitherto overlooked marine megafauna.

Oblique Collision of the Leeward Antilles, Offshore Venezuela: Linking Onshore and Offshore Data from BOLIVAR

NASA Astrophysics Data System (ADS)

Beardsley, A. G.; Avé Lallemant, H. G.; Levander, A.; Clark, S. A.

2006-12-01

The kinematic history of the Leeward Antilles (offshore Venezuela) can be characterized with the integration of onshore outcrop data and offshore seismic reflection data. Deformation structures and seismic interpretation show that oblique convergence and wrench tectonics have controlled the diachronous deformation identified along the Caribbean - South America plate boundary. Field studies of structural features in outcrop indicate one generation of ductile deformation (D1) structures and three generations of brittle deformation (F1 - F3) structures. The earliest deformation (D1/F1) began ~ 110 Ma with oblique convergence between the Caribbean plate and South American plate. The second generation of deformation (F2) structures initiated in the Eocene with the extensive development of strike-slip fault systems along the diffuse plate boundary and the onset of wrench tectonics within a large-scale releasing bend. The most recent deformation (F3) has been observed in the west since the Miocene where continued dextral strike-slip motion has led to the development of a major restraining bend between the Caribbean plate transform fault and the Oca - San Sebastian - El Pilar fault system. Deformation since the late Cretaceous has been accompanied by a total of 135° clockwise rotation. Interpretation of 2D marine reflection data indicates similar onshore and offshore deformation trends. Seismic lines that approximately parallel the coastline (NW-SE striking) show syndepositional normal faulting during F1/F2 and thrust faulting associated with F3. On seismic lines striking NNE-SSW, we interpret inversion of F2 normal faults with recent F3 deformation. We also observe both normal and thrust faults related to F3. The thick sequence of recent basin sedimentation (Miocene - Recent), interpreted from the seismic data, supports the ongoing uplift and erosion of the islands; as suggested by fluid inclusion analysis. Overall, there appears to be a strong correlation between onshore micro- and mesoscopic deformational structures and offshore macro-scale structural features seen in the reflection data. The agreement of features supports our regional deformation and rotation model along the Caribbean - South America obliquely convergent plate boundary.

A database of archived drilling records of the drill cuttings piles at the North West Hutton oil platform.

PubMed

Marsh, Roy

2003-05-01

Drill cuttings piles are found underneath several hundred oil platforms in the North Sea, and are contaminated with hydrocarbons and chemical products. This study characterised the environmental risk posed by the cuttings pile at the North West Hutton (NWH) oil platform. Data on the drilling fluids and chemical products used over the platform's drilling history were transferred from archived well reports into a custom database, to which were added toxicological and safety data. Although the database contained many gaps, it established that only seven chemical products used at NWH were not in the lowest category of the Offshore Chemicals Notification Scheme, and were used in only small quantities. The study therefore supports the view that the main environmental risk posed by cuttings piles comes from hydrocarbon contamination. The (dated) well records could help future core sampling to be targeted at specific locations in the cuttings piles. Data from many platforms could also be pooled to determine generic 'discharge profiles.' Future study would benefit from the existence, in the public domain, of a standardised, 'legacy' database of chemical products.

How a good understanding of the physical oceanography of your offshore renewables site can drive down project costs.

NASA Astrophysics Data System (ADS)

Royle, J.

2016-02-01

For an offshore renewables plant to be viable it must be safe and cost effective to build and maintain (i.e. the conditions mustn't be too harsh to excessively impede operations at the site), it must also have an energetic enough resource to make the project attractive to investors. In order to strike the correct balance between cost and resource reliable datasets describing the meteorological and oceanographic (metocean) environment needs to be collected, analysed and its findings correctly applied . This presentation will use three real world examples from Iberdrola`s portfolio of offshore windfarms in Europe to demonstrate the economic benefits of good quality metocean data and robust analysis. The three examples are: 1) Moving from traditional frequency domain persistence statistics to time domain installation schedules driven by reliable metocean data reduces uncertainty and allows the developer to have better handle on weather risk during contract negotiations. 2) By comparing the planned installation schedules from a well validated metocean dataset with a coarser low cost unvalidated metocean dataset we can show that each Euro invested in the quality of metocean data can reduce the uncertainty in installation schedules by four Euros. 3) Careful consideration of co-varying wave and tidal parameters can justify lower cost designs, such as lower platform levels leading to shorter and cheaper offshore wind turbine foundations. By considering the above examples we will prove the case for investing in analysis of well validated metocean models as a basis for sound financial planning of offshore renewables installations.

Observations and a model of undertow over the inner continental shelf

USGS Publications Warehouse

Lentz, Steven J.; Fewings, Melanie; Howd, Peter; Fredericks, Janet; Hathaway, Kent

2008-01-01

Onshore volume transport (Stokes drift) due to surface gravity waves propagating toward the beach can result in a compensating Eulerian offshore flow in the surf zone referred to as undertow. Observed offshore flows indicate that wave-driven undertow extends well offshore of the surf zone, over the inner shelves of Martha’s Vineyard, Massachusetts, and North Carolina. Theoretical estimates of the wave-driven offshore transport from linear wave theory and observed wave characteristics account for 50% or more of the observed offshore transport variance in water depths between 5 and 12 m, and reproduce the observed dependence on wave height and water depth.During weak winds, wave-driven cross-shelf velocity profiles over the inner shelf have maximum offshore flow (1–6 cm s−1) and vertical shear near the surface and weak flow and shear in the lower half of the water column. The observed offshore flow profiles do not resemble the parabolic profiles with maximum flow at middepth observed within the surf zone. Instead, the vertical structure is similar to the Stokes drift velocity profile but with the opposite direction. This vertical structure is consistent with a dynamical balance between the Coriolis force associated with the offshore flow and an along-shelf “Hasselmann wave stress” due to the influence of the earth’s rotation on surface gravity waves. The close agreement between the observed and modeled profiles provides compelling evidence for the importance of the Hasselmann wave stress in forcing oceanic flows. Summer profiles are more vertically sheared than either winter profiles or model profiles, for reasons that remain unclear.

Preliminary interpretation of high resolution 3D seismic data from offshore Mt. Etna, Italy

NASA Astrophysics Data System (ADS)

Gross, F.; Krastel, S.; Chiocci, F. L.; Ridente, D.; Cukur, D.; Bialas, J.; Papenberg, C. A.; Crutchley, G.; Koch, S.

2013-12-01

In order to gain knowledge about subsurface structures and its correlation to seafloor expressions, a hydro-acoustic dataset was collected during RV Meteor Cruise M86/2 (December 2011/January 2012) in Messina Straits and offshore Mt. Etna. Especially offshore Mt. Etna, the data reveals an obvious connection between subsurface structures and previously known morphological features at the sea floor. Therefore a high resolution 3D seismic dataset was acquired between Riposto Ridge and Catania Canyon close to the shore of eastern Sicily. The study area is characterized by a major structural high, which hosts several ridge-like features at the seafloor. These features are connected to a SW-NE trending fault system. The ridges are bended in their NE-SW direction and host major escarpments at the seafloor. Furthermore they are located directly next to a massive amphitheater structure offshore Mt. Etna with slope gradients of up to 35°, which is interpreted as remnants of a massive submarine mass wasting event off Sicily. The new 3D seismic dataset allows an in depth analysis of the ongoing deformation of the east flank of Mt. Etna.

Calcareous nannofossil evidence for the existence of the Gulf Stream during the late Maastrichtian

USGS Publications Warehouse

Watkins, D.K.; ,

2005-01-01

Upper Maastrichtian calcareous nannofossil assemblages, from eight cores on the South Carolina Coastal Plain (onshore set) and three deep sea drilling sites from the continental slope and abyssal hills (offshore set), were analyzed by correlation and principal component analysis to examine the ancient surface water thermal structure. In addition, a temperature index derived from independently published paleobiogeographic information was applied to the sample data. All three methods indicate a strong separation of the samples into onshore and offshore sets, with the offshore data set exhibiting significantly warmer paleotemperatures. The great disparity between these two sample sets indicates that there was a strong thermal contrast between the onshore and offshore surface water masses that persisted throughout the late Maastrichtian despite evident shortterm changes in fertility, productivity, and community structure. This suggests the Gulf Stream was present as a major oceanographic feature during the late Maastrichtian. Copyright 2005 by the American Geophysical Union.

Nuclear and Mitochondrial Patterns of Population Structure in North Pacific False Killer Whales (Pseudorca crassidens)

DTIC Science & Technology

2014-05-14

microsatellite loci from 206 individuals to examine levels of differentiation among the 2 island-associated populations and offshore animals from the...they are from offshore animals . The patterns of differentiation revealed by the 2 marker types suggest that the island-associated false killer whale...False killer whales (Pseudorca crassidens) are large delphinids typically found in deep water far offshore . However, in the Hawaiian Archipelago

Gis-Based Wind Farm Site Selection Model Offshore Abu Dhabi Emirate, Uae

NASA Astrophysics Data System (ADS)

Saleous, N.; Issa, S.; Mazrouei, J. Al

2016-06-01

The United Arab Emirates (UAE) government has declared the increased use of alternative energy a strategic goal and has invested in identifying and developing various sources of such energy. This study aimed at assessing the viability of establishing wind farms offshore the Emirate of Abu Dhabi, UAE and to identify favourable sites for such farms using Geographic Information Systems (GIS) procedures and algorithms. Based on previous studies and on local requirements, a set of suitability criteria was developed including ocean currents, reserved areas, seabed topography, and wind speed. GIS layers were created and a weighted overlay GIS model based on the above mentioned criteria was built to identify suitable sites for hosting a new offshore wind energy farm. Results showed that most of Abu Dhabi offshore areas were unsuitable, largely due to the presence of restricted zones (marine protected areas, oil extraction platforms and oil pipelines in particular). However, some suitable sites could be identified, especially around Delma Island and North of Jabal Barakah in the Western Region. The environmental impact of potential wind farm locations and associated cables on the marine ecology was examined to ensure minimal disturbance to marine life. Further research is needed to specify wind mills characteristics that suit the study area especially with the presence of heavy traffic due to many oil production and shipping activities in the Arabian Gulf most of the year.

Geriatric infrastructure, BRAC, and ecosystem service markets? End-of-life decisions for dams, roads, and offshore platforms (Invited)

NASA Astrophysics Data System (ADS)

Doyle, M. W.

2010-12-01

US infrastructure expanded dramatically in the mid-20th century, and now includes more than 79,000 dams, 15,000 miles of levees, 3.7 million miles of roads, 600,000 miles of sewer pipe, 500,000 onshore oil wells, and over 4,000 offshore oil platforms. Many structures have been in place for 50 years or more, and an increasing portion of national infrastructure is approaching or exceeding its originally intended design life. Bringing national infrastructure to acceptable levels would cost nearly 10% of the US annual GDP. Decommissioning infrastructure can decrease public spending and increase public safety while facilitating economic expansion and ecological restoration. While most infrastructure remains critical to the national economy, a substantial amount is obsolete or declining in importance. Over 11,000 dams are abandoned, and of nearly 400,000 miles of road on its lands, the U.S. Forest Service considers one-fourth non-essential and often non-functional. Removing obsolete infrastructure allows greater focus and funding on maintaining or improving infrastructure most critical to society. Moreover, a concerted program of infrastructure decommissioning promises significant long-term cost savings, and is a necessary step before more substantial, systematic changes are possible, like those needed to address the new energy sources and shifting climate. One key challenge for infrastructure reform is how to prioritize and implement such a widespread and politically-charged series of decisions. Two approaches are proposed for different scales. For small, private infrastructure, emerging state and federal ecosystem service markets can provide an economic impetus to push infrastructure removal. Ecosystem market mechanisms may also be most effective at identifying those projects with the greatest ecological bang for the buck. Examples where this approach has proved successful include dam removal for stream mitigation under the Clean Water Act, and levee decommissioning on the Missouri and Iowa Rivers for wildlife conservation areas. Programs that link offshore oil platform decommissioning to marine conservation areas are also notable examples of creative linkages between infrastructure and conservation efforts. For federal infrastructure, the forthcoming Water Resources Development Act (WRDA) should include a BRAC-like program. Faced with a number of aging military bases, the Department of Defense (DOD) began identifying installations it would rather close than maintain or modernize. Overcoming political hurdles was accomplished via the Base Realignment and Closure Commission (BRAC), a bi-partisan commission that buffered politicians by creating a slate of closures for Congress and the President to approve or scuttle in toto. From 1988-2005, BRACs closed > 125 military installations, saving > $50 billion. DOD advocated BRAC because it increased efficiency by focusing funding on those bases central to DODs mission, and removed base funding decisions from political influence. Regardless of the approach, society must develop approaches from which to base difficult end-of-life decisions for infrastructure. In most cases, removing obsolete infrastructure can allow focus on infrastructure that remains critical to society.

The northern Lesser Antilles oblique subduction zone: new insight about the upper plate deformation, 3D slab geometry and interplate coupling.

NASA Astrophysics Data System (ADS)

Marcaillou, B.; Laurencin, M.; Graindorge, D.; Klingelhoefer, F.

2017-12-01

In subduction zones, the 3D geometry of the plate interface is thought to be a key parameter for the control of margin tectonic deformation, interplate coupling and seismogenic behavior. In the northern Caribbean subduction, precisely between the Virgin Islands and northern Lesser Antilles, these subjects remain controversial or unresolved. During the ANTITHESIS cruises (2013-2016), we recorded wide-angle seismic, multichannel reflection seismic and bathymetric data along this zone in order to constrain the nature and the geometry of the subducting and upper plate. This experiment results in the following conclusions: 1) The Anegada Passage is a 450-km long structure accross the forearc related to the extension due to the collision with the Bahamas platform. 2) More recently, the tectonic partitioning due to the plate convergence obliquity re-activated the Anegada Passage in the left-lateral strike-slip system. The partitioning also generated the left-lateral strike-slip Bunce Fault, separating the accretionary prism from the forearc. 3) Offshore of the Virgin Islands margin, the subducting plate shows normal faults parallel to the ancient spreading center that correspond to the primary fabric of the oceanic crust. In contrast, offshore of Barbuda Island, the oceanic crust fabric is unresolved (fracture zone?, exhumed mantle? ). 4) In the direction of the plate convergence vector, the slab deepening angle decreases northward. It results in a shallower slab beneath the Virgin Islands Platform compared to the St Martin-Barbuda forearc. In the past, the collision of the Bahamas platform likely changed the geodynamic settings of the northeastern corner of the Caribbean subduction zone and we present a revised geodynamic history of the region. Currently, various features are likely to control the 3D geometry of the slab: the margin convexity, the convergence obliquity, the heterogeneity of the primary fabric of the oceanic crust and the Bahamas docking. We suggest that the slab deepening angle lower beneath the Virgin Islands segment than beneath the St Martin-Barbuda segment possibly generates a northward increasing interplate coupling. As a result, it possibly favors an increase in the seismic activity and the tectonic partitioning beneath the Virgin Islands margin contrary to the St Martin-Barbuda segment.

Seismicity and gravimetric studies of Cyrenaica platform and adjacent regions, northeastern Libya

NASA Astrophysics Data System (ADS)

Ben Suleman, abdunnur

2013-04-01

Cyrenaica, located in northeastern Libya, consists of two distinct tectonic provinces; the tectonically unstable northern Cyrenaica and the more stable Cyernaican platform to the south. This study represents detailed investigations that aim to focus on the structure and tectonic setting through a detailed Seismicity and gravity analysis. Seismicity of northeastern Libya is documented back to 262 A.D. when an earthquake destroyed the city of Ceryne. The same area was destroyed by an earthquake in 365 A.D, The city of Al-Maraj was heavily damaged in 1963 by an earthquake measuring 5,3 in the Richter scale. Data collected by the recently established Libyan National Seismograph Network confirms that northeastern Libya is seismically active with most of the activity concentrates on the northern part particularly in the city of Al-Maraj area. Seismic activity is also noticeable in the offshore area. Focal mechanism studies for a number of earthquakes recorded by the Libyan National Seismograph Network suggest that normal faulting is predominant. A gravity data base collected from a variety of sources was compiled to generate a Bouguer gravity anomaly map that represents the basic map used in the overall interpretations, as well as in generating more specialized gravity maps used in the detailed investigations. The Bouguer gravity map demonstrates that the northern inverted basins of Cyrenaica and the coastal plain of Al-Jabal Al-Akhdar show a raped northward increase in gravity values to up to 130 Mgal. In addition a series of steep faults that separates the unstable Al-Jabal Al-Akhdar from the more stable Cyrenaica platform as well as other faults within the platform were well delineated.

Offshore oil in the Alaskan Arctic

NASA Technical Reports Server (NTRS)

Weeks, W. F.; Weller, G.

1984-01-01

Oil and gas deposits in the Alaskan Arctic are estimated to contain up to 40 percent of the remaining undiscovered crude oil and oil-equivalent natural gas within U.S. jurisdiction. Most (65 to 70 percent) of these estimated reserves are believed to occuur offshore beneath the shallow, ice-covered seas of the Alaskan continental shelf. Offshore recovery operations for such areas are far from routine, with the primary problems associated with the presence of ice. Some problems that must be resolved if efficient, cost-effective, environmentally safe, year-round offshore production is to be achieved include the accurate estimation of ice forces on offshore structures, the proper placement of pipelines beneath ice-produced gouges in the sea floor, and the cleanup of oil spills in pack ice areas.

Direct growth of cerium oxide nanorods on diverse substrates for superhydrophobicity and corrosion resistance

NASA Astrophysics Data System (ADS)

Cho, Young Jun; Jang, Hanmin; Lee, Kwan-Soo; Kim, Dong Rip

2015-06-01

Superhydrophobic surfaces with anti-corrosion properties have attracted great interest in many industrial fields, particularly to enhance the thermal performance of offshore applications such as heat exchangers, pipelines, power plants, and platform structures. Nanostructures with hydrophobic materials have been widely utilized to realize superhydrophobicity of surfaces, and cerium oxide has been highlighted due to its good corrosion resistive and intrinsically hydrophobic properties. However, few studies of direct growth of cerium oxide nanostructures on diverse substrates have been reported. Herein we report a facile hydrothermal method to directly grow cerium oxide nanorods on diverse substrates, such as aluminum alloy, stainless steel, titanium, and silicon. Diverse substrates with cerium oxide nanorods exhibited superhydrophobicity with no hydrophobic modifiers on their surfaces, and showed good corrosion resistive properties in corrosive medium. We believe our method could pave the way for realization of scalable and sustainable corrosion resistive superhydrophobic surfaces in many industrial fields.

Mobile Launch Platform (MLP) Environmental Assessment

DTIC Science & Technology

2004-06-28

Sometimes these winds are interrupted by cool seasonal storms with southerly winds; dry offshore storms with southeasterly winds, called Santa Ana...winds; coastal eddies during the warm season with southeasterly winds over the inner waters; and alternating land and sea breezes that occur closer to...mean temperature of 14 oC (58 oF). Total annual precipitation averages 21.3 centimeters (8.4 inches). The dry season ranges from May to September and

Full load shop testing of 18,000-hp gas turbine driven centrifugal compressor for offshore platform service: Evaluation of rotor dynamics performance

NASA Technical Reports Server (NTRS)

Kirk, R. G.; Simpson, M.

1985-01-01

The results for in-plant full load testing of a 13.4 MW (18000 HP) gas turbine driven centrifugal compressor are presented and compared to analytical predictions of compressor rotor stability. Unique problems from both oil seals and labyrinth gas seals were encountered during the testing. The successful resolution of these problems are summarized.

Mapping the extent of thinned continental crust across the Orphan Basin, offshore Newfoundland, Canada, using a combination of vintage and new seismic refraction/wide-angle reflection data

NASA Astrophysics Data System (ADS)

Welford, J. Kim; Dehler, Sonya; Funck, Thomas

2017-04-01

The SIGNAL (Seismic Investigations off Greenland, Newfoundland and Labrador) 2009 cruise was undertaken by the Geological Survey of Canada (GSC) and the Geological Survey of Denmark and Greenland (GEUS), with scientific contributions from Dalhousie University, to collect refraction/wide-angle reflection (RWAR) profiles as part of each country's continental shelf program under UNCLOS (United Nations Convention on the Law of the Sea) Article 76. Line 1 extended from the Bonavista Platform off Newfoundland, across the Orphan Basin, to Orphan Knoll and beyond into oceanic crust. The line followed the same track as an earlier seismic refraction line and ocean-bottom seismometer (OBS) locations were chosen to complement and to extend the original station coverage. The final crustal velocity model across Orphan Basin shows thinned continental crust (15 to 20 km thick) beneath most of the basin with thinner crust (10 km thick) immediately outboard of the Bonavista Platform, interpreted as a failed rift zone. Seaward of the failed rift, the velocity structure of the thinned continental crust is generally uniform over 250 km toward Orphan Knoll. Immediately outboard of Orphan Knoll, the crust thins to 8 km and exhibits a velocity structure consistent with oceanic crust. The results from modelling of the combined refraction/wide-angle reflection dataset support an extension of Canada's continental shelf beyond the seaward limits of the Orphan Basin.

Environmental impacts of produced water and drilling waste discharges from the Norwegian offshore petroleum industry.

PubMed

Bakke, Torgeir; Klungsøyr, Jarle; Sanni, Steinar

2013-12-01

Operational discharges of produced water and drill cuttings from offshore oil and gas platforms are a continuous source of contaminants to continental shelf ecosystems. This paper reviews recent research on the biological effects of such discharges with focus on the Norwegian Continental Shelf. The greatest concern is linked to effects of produced water. Alkylphenols (AP) and polyaromatic hydrocarbons (PAH) from produced water accumulate in cod and blue mussel caged near outlets, but are rapidly metabolized in cod. APs, naphtenic acids, and PAHs may disturb reproductive functions, and affect several chemical, biochemical and genetic biomarkers. Toxic concentrations seem restricted to <2 km distance. At the peak of discharge of oil-contaminated cuttings fauna disturbance was found at more than 5 km from some platforms, but is now seldom detected beyond 500 m. Water-based cuttings may seriously affect biomarkers in filter feeding bivalves, and cause elevated sediment oxygen consumption and mortality in benthic fauna. Effects levels occur within 0.5-1 km distance. The stress is mainly physical. The risk of widespread, long term impact from the operational discharges on populations and the ecosystem is presently considered low, but this cannot be verified from the published literature. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Ocean products delivered by the Mercator Ocean Service Department

NASA Astrophysics Data System (ADS)

Crosnier, L.; Durand, E.; Soulat, F.; Messal, F.; Buarque, S.; Toumazou, V.; Landes, V.; Drevillon, M.; Lellouche, J.

2008-12-01

The newly created Service Department at Mercator Ocean is now offering various services for academic and private ocean applications. Mercator Ocean runs operationally ocean forecast systems for the Global and North Atlantic Ocean. These systems are based on an ocean general circulation model NEMO as well as on data assimilation of sea level anomalies, sea surface temperature and temperature and salinity vertical profiles. Three dimensional ocean fields of temperature, salinity and currents are updated and available weekly, including analysis and 2 weeks forecast fields. The Mercator Ocean service department is now offering a wide range of ocean derived products. This presentation will display some of the various products delivered in the framework of academic and private ocean applications: " Monitoring of the ocean current at the surface and at depth in several geographical areas for offshore oil platform, for offshore satellite launch platform, for transatlantic sailing or rowing boat races. " Monitoring of ocean climate indicators (Coral bleaching...) for marine reserve survey; " Monitoring of upwelling systems for fisheries; " Monitoring of the ocean heat content for tropical cyclone monitoring. " Monitoring of the ocean temperature/salinity and currents to guide research vessels during scientific cruises. The Mercator Ocean products catalogue will grow wider in the coming years, especially in the framework of the European GMES MyOcean project (FP7).

Concept design and coupled dynamic response analysis on 6-MW spar-type floating offshore wind turbine

NASA Astrophysics Data System (ADS)

Meng, Long; Zhou, Tao; He, Yan-ping; Zhao, Yong-sheng; Liu, Ya-dong

2017-10-01

Tower, Spar platform and mooring system are designed in the project based on a given 6-MW wind turbine. Under wind-induced only, wave-induced only and combined wind and wave induced loads, dynamic response is analyzed for a 6-MW Spar-type floating offshore wind turbine (FOWT) under operating conditions and parked conditions respectively. Comparison with a platform-fixed system (land-based system) of a 6-MW wind turbine is carried out as well. Results demonstrate that the maximal out-of-plane deflection of the blade of a Spar-type system is 3.1% larger than that of a land-based system; the maximum response value of the nacelle acceleration is 215% larger for all the designed load cases being considered; the ultimate tower base fore-aft bending moment of the Spar-type system is 92% larger than that of the land-based system in all of the Design Load Cases (DLCs) being considered; the fluctuations of the mooring tension is mainly wave-induced, and the safety factor of the mooring tension is adequate for the 6-MW FOWT. The results can provide relevant modifications to the initial design for the Spar-type system, the detailed design and model basin test of the 6-MW Spar-type system.

Late Quaternary uplift rate across the Shimokita peninsula, northeastern Japan forearc

NASA Astrophysics Data System (ADS)

Matsu'Ura, T.

2009-12-01

I estimated the late Quaternary uplift rate across the northeastern Japan forearc (Shimokita peninsula) by using the height distribution of MIS 5.5 marine terraces as determined from tephra and cryptotephra stratigraphy. The heights of inner-margins (shoreline angles) of the MIS 5.5 marine terrace surface were previously reported to be 43-45 m and 30 m around Shiriyazaki and Gamanosawa, respectively. These heights decrease westward and are possibly due to a west-dipping offshore fault. But in some places, the heights of terrace inner-margins are probably overestimated by thick sediments. I found the MIS 5.5 wave-cut platform which is overlain by gravels and loess deposits containing a basal Toya tephra horizon (MIS 5.4) at Shiriyazaki by boring. The MIS 5.5 wave-cut platform (paleo sea level) is about 25 m above sea level, nearly half of the reported height of the terrace inner-margin. My result shows that the late Quaternary uplift rate across the Shimokita peninsula should be reconsidered. Further studies are also required whether or not the intra-plate (offshore) fault is a factor of the forearc uplifting at the peninsula. This research project has been conducted under the research contract with Nuclear and Industrial Safety Agency (NISA).

Nonconsensual clinical trials: a foreseeable risk of offshoring under global corporatism.

PubMed

Spielman, Bethany

2015-03-01

This paper explores the connection of offshoring and outsourcing to nonconsensual global pharmaceutical trials in low-income countries. After discussing reasons why the topic of nonconsensual offshored clinical trials may be overlooked in bioethics literature, I suggest that when pharmaceutical corporations offshore clinical trials today, nonconsensual experiments are often foreseeable and not simply the result of aberrant ethical conduct by a few individuals. Offshoring of clinical trials is structured so that experiments can be presented as health care in a unique form of outsourcing from the host country to pharmaceutical corporations. Bioethicists' assessments of the risks and potential benefits of offshore corporate pharmaceutical trials should therefore systematically include not only the hoped for benefits and the risks of the experimental drug but also the risk that subjects will not have consented, as well as the broader international consequences of nonconsensual experimentation.

Petroleum geology and resources of southeastern Mexico, northern Guatemala, and Belize

USGS Publications Warehouse

Peterson, James A.

1983-01-01

Petroleum deposits in southeastern Mexico and Guatemala occur in two main basinal provinces, the Gulf Coast Tertiary basin area, which includes the Reforma and offshore Campeche Mesozoic fields, and the Peten basin of eastern Chiapas State (Mexico) and Guatemala. Gas production is mainly from Tertiary sandstone reservoirs of Miocene age. Major oil production, in order of importance, is from Cretaceous, Paleocene, and Jurassic carbonate reservoirs in the Reforma and offshore Campeche areas. Several small oil fields have been discovered in Cretaceous carbonate reservoirs in west-central Guatemala, and one major discovery has been reported in northwestern Guatemala. Small- to medium-sized oil accumulations also occur in Miocene sandstone reservoirs on salt structures in the Isthmus Saline basin of western Tabasco State, Mexico. Almost all important production is in salt structure traps or on domes and anticlines that may be related to deep-seated salt structures. Some minor oil production has occurred in Cretaceous carbonate reservoirs in a buried overthrust belt along the west flank of the Veracruz basin. The sedimentary cover of Paleozoic through Tertiary rocks ranges in thickness from about 6,000 m (20,000 ft) to as much as 12,000 m (40,000 ft) or more in most of the region. Paleozoic marine carbonate and clastic rocks 1,000 to 2,000 m (3,300 to 6,500 ft) thick overlie the metamorphic and igneous basement in part of the region; Triassic through Middle Jurassic red beds and evaporite deposits, including halite, apparently are present throughout the region, deposited in part in a Triassic graben system. Upper Jurassic (Oxfordian) through Cretaceous rocks make up the bulk of the Mesozoic regional carbonate bank complex, which dominates most of the area. Tertiary marine and continental clastic rocks, some of deep water origin, 3,000 to 10,000 m (10,000 to 35,000 ft) thick, are present in the coastal plain Tertiary basins. These beds grade eastward into a carbonate sequence that overlies the Mesozoic carbonate complex on the Yucatan platform. During the past 10 years, about 50 large oil fields were discovered in the Reforma and offshore Campeche areas. Oil is produced from intensely microfractured Cretaceous, Paleocene, and Upper Jurassic dolomite reservoirs on blockfaulted salt swells or domes. Most fields are located in the Mesozoic carbonate-bank margin and forebank talus (Tamabra) facies, which passes through the offshore Campeche and onshore Reforma areas. Oil source rocks are believed to be organic-rich shales and shaly carbonate rocks of latest Jurassic and possibly Early Cretaceous age. At least six of the Mesozoic discoveries are giant or supergiant fields. The largest is the Cantarell complex (about 8 billion to 10 billion barrels (BB)) in the offshore Campeche area and the Bermudez complex (about 8 BB) in the Reforma onshore area. Oil columns are unusually large (from 50 m to as much as 1,000 m, or 160 ft to 3,300 ft). Production rates are extremely high, averaging at least 3,000 to 5,000 barrels of oil per day (bo/d); some wells produce more than 20,000 bo/d, particularly in the offshore Campeche area, where 30,000- to 60,000-bo/d wells are reported. Tertiary basin fields produce primarily from Miocene sandstone reservoirs. About 50 of these are oil fields ranging from 1 million barrels (MMB) to 200 MMB in size, located on faulted salt structures in the Isthmus Saline basin. Another 30 are gas or gas-condensate fields of a few billion cubic feet to 3 trillion to 4 trillion cubic feet (Tcf) located on salt structures or probable salt structures in the Macuspana, Comalcalco, Isthmus Saline, and Veracruz basins. Source rocks for the gas are believed to be carbonaceous shales interbedded with the sandstone reservoir bodies. Identified reserves in the southeastern Mexico-Guatemala area, almost all in the Mesozoic fields, are about 53 BB of oil, 3 BB of natural gas liquids, and 65 Tcf of gas. The estimat

How to install platforms in tidal deltaic areas: The 25-year experience of Total in Kalimantan (Indonesia)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quenelle, A.; Metz, R.; Poirier, D.

1994-12-31

Due to the extended work by TOTAL, since 1971, offshore and within the Mahakam delta (East Kalimantan), several installation and platform concepts have been used. The present paper only concerns the installations at Handil and Tambora sites located in the Mahakam delta (in-shore) where water depths are between 2 and 4 meters, water current is 2 knots max. and tide is 2 meters as an average. The experience gained by the company in this kind of job made it possible to recently install in a single piece large and heavy integrated decks (up to 2,600 t) with the optimum usemore » of local skills, non-sophisticated technology and at low costs. The following shows the historical and evolutive experience of TOTAL up to now in platform concepts in this area of the world and gives, by the way, some useful information for future work.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lepage, A.

Despite scheduling complications caused by annual monsoons, the Yadana project to bring offshore Myanmar gas ashore and into neighboring Thailand has met it first-gas target of July 1, 1998. The Yadana field is a dry-gas reservoir in the reef upper Birman limestone formation t 1,260 m and a pressure of 174 bara (approximately 2,500 psi). It extends nearly 7 km (west to east) and 10 km (south to north). The water-saturated reservoir gas contains mostly methane mixed with CO{sub 2} and N{sub 2}. No production of condensate is anticipated. The Yadana field contains certified gas reserves of 5.7 tcf, calculatedmore » on the basis of 2D and 3D seismic data-acquisition campaigns and of seven appraisal wells. The paper discusses early interest, development sequences, offshore platforms, the gas-export pipeline, safety, environmental steps, and schedule constraints.« less

East Kalimantan project recovers 200 MMscfd of associated gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nacouz, E.

1984-02-06

Bekapai and Handil fields were discovered in 1972 and 1974 and in the Mahakam offshore Permit, East Kalimantan (Fig. 1). They are operated by Total Indonesie in association with Inpex under a production sharing contract with Pertamina. Oil production of the fields is about 200,000 b/d. Associated gas, until the construction of the facilities described here, were flared. Associated gas production is about 200 MMscfd. The Bekapai field is 40 km offshore in 35 m of water. The Handil field, located in the delta of the Mahakam, has a gathering system and platformmounted central process area. After a first stagemore » of separation at the Bekapai production platform and the central process area of Handil, the production of both fields is sent through pipelines to Senipah terminal onshore for final separation, processing, and storage before shipment.« less

A Comprehensive Structural Study of Offshore Wind Turbine Foundation and Non-Model Based Damage Detection using Effective Mass with Application to Small Components/ Cables and a Truss Wind Turbine Tower

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Scott A.

This research has two areas of focus. The first area is to investigate offshore wind turbine (OWT) designs, for use in the Maryland offshore wind area (MOWA), using intensive modeling techniques. The second focus area is to investigate a way to detect damage in wind turbine towers and small electrical components.

Foundations for offshore wind turbines.

PubMed

Byrne, B W; Houlsby, G T

2003-12-15

An important engineering challenge of today, and a vital one for the future, is to develop and harvest alternative sources of energy. This is a firm priority in the UK, with the government setting a target of 10% of electricity from renewable sources by 2010. A component central to this commitment will be to harvest electrical power from the vast energy reserves offshore, through wind turbines or current or wave power generators. The most mature of these technologies is that of wind, as much technology transfer can be gained from onshore experience. Onshore wind farms, although supplying 'green energy', tend to provoke some objections on aesthetic grounds. These objections can be countered by locating the turbines offshore, where it will also be possible to install larger capacity turbines, thus maximizing the potential of each wind farm location. This paper explores some civil-engineering problems encountered for offshore wind turbines. A critical component is the connection of the structure to the ground, and in particular how the load applied to the structure is transferred safely to the surrounding soil. We review previous work on the design of offshore foundations, and then present some simple design calculations for sizing foundations and structures appropriate to the wind-turbine problem. We examine the deficiencies in the current design approaches, and the research currently under way to overcome these deficiencies. Designs must be improved so that these alternative energy sources can compete economically with traditional energy suppliers.

VECTORS of change in the marine environment: Ecosystem and economic impacts and management implications

NASA Astrophysics Data System (ADS)

Austen, M. C.; Crowe, T. P.; Elliott, M.; Paterson, D. M.; Peck, M. A.; Piraino, S.

2018-02-01

Human use of the European marine environment is increasing and diversifying. This is creating new mechanisms for human induced-changes in marine life which need to be understood and quantified as well as the impact of these changes on ecosystems, their structures (e.g. biodiversity) and functioning (e.g. productivity), and the social and economic consequences that arise. The current and emerging pressures are multiple and interacting, arising, for example, from transport, platforms for renewable and non-renewable energy, exploitation of living and non-living resources, agricultural and industrial discharges, together with wider environmental changes (including climate change). Anticipating the future consequences of these pressures and vectors of change for marine life and of adaptation and mitigation measures (such as the introduction of new technologies and structures, new ballast water practices, ocean and offshore wind energy devices and new fishing strategies) is a prerequisite to the development and implementation of strategies, policies and regulations to manage the marine environment, such as the IMO Convention on ballast water management and the EU Maritime Policy and Marine Strategy Framework Directive.

Offshore sand resources for coastal erosion control in Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramsey, K.E.; Penland, S.; McBride, R.A.

1990-09-01

An inventory of existing geophysical data supplemented by more than 15,000 km of high-resolution seismic profiles and 400 vibracores collected cooperatively by the Louisiana Geological Survey and US Geological Survey since 1981 indicates that a wide range of aggregate minerals occurs on the continental shelf in a variety of depositional settings. The distribution of these deposits is controlled by the geometry of the preexisting fluvial and deltaic channel systems and the stratigraphic signature of the Holocene Transgression across these features. The geology of coastal and offshore Louisiana is tied to the depositional history of the Mississippi River. Offshore of themore » delta plain, five types of aggregate sources can be identified: inner shelf shoals, submerged barrier islands, tidal inlets, distributary channels, and barrier platforms. This paper describes the geology of offshore Louisiana, the available geophysical data sets, and the distribution of aggregate mineral resources. On the continental shelf of the Mississippi River delta plain, two extensive seismic survey grids have been developed by the Louisiana Geological Survey and US Geological Survey. The most prospective resources found are the huge sand bodies of Ship Shoal and associated distributaries, Cat Island Pass tidal channels and associated tidal deltas, and Barataria Pass/Grand Terre tidal channels and associated tidal deltas. East of the mouth of the Mississippi River are the Chandeleur Islands, where LGS identified seven major sand resource targets, truncated barrier-spit and tidal inlet deposits, submerged beach ridges, and distributaries associated with abandoned St. Bernard delta complexes. Abundant sand resources can be found in offshore Louisiana. Many of the sand bodies contain heavy minerals, but their concentration and distribution is unknown. Other potential sand resources not yet adequately explored include Sabine Bank, the Outer Shoal, and the St. Bernard shoal.« less

Tidally driven pore water exchange in offshore intertidal sandbanks: Part I. Field measurements

NASA Astrophysics Data System (ADS)

Gibbes, B.; Robinson, C.; Carey, H.; Li, L.; Lockington, D.

2008-08-01

In recent years blooms of the toxic marine cyanobacteria Lyngbya majuscula have been frequently observed in a system of offshore intertidal sandbanks in Moreton Bay, Australia. Past research suggests that these blooms are linked to the presence of bio-available forms of iron. Using hydraulic and pore water chemistry data collected from a shore normal transect at an offshore bloom site, the role of tidally driven exchange as a potential mechanism for delivery of bio-available iron across the sediment-water interface was examined. Field data revealed a residual pore water flow system in the sandbank, with seawater entering the upper sandbank platform and discharging through the bank edge. Upward flow and elevated near-surface dissolved Fe(II) concentrations (>20 μM Fe(II) at -0.05 m depth) were measured simultaneously in the discharge zones at the sandbank edge. The measured concentrations were more than four times greater than concentrations previously shown to stimulate L. majuscula growth. These results suggest that the tidally driven exchange mechanism might be capable of delivering dissolved Fe(II) to sites within offshore intertidal sandbanks where blooms of L. majuscula have been observed. While the source of the iron was not identified, potential candidates are discussed. These findings have implications for the current conceptual model for L. majuscula blooms in offshore intertidal sandbanks within Moreton Bay. Further investigations are required to fully understand the role of tidally driven exchange in controlling the export of bio-available iron to coastal waters at the field site. In particular there is a need to better assess the link between the pore water flows and the geochemical reactions that might occur along the flow path.

Optimisation and evaluation of pre-design models for offshore wind turbines with jacket support structures and their influence on integrated load simulations

NASA Astrophysics Data System (ADS)

Schafhirt, S.; Kaufer, D.; Cheng, P. W.

2014-12-01

In recent years many advanced load simulation tools, allowing an aero-servo-hydroelastic analyses of an entire offshore wind turbine, have been developed and verified. Nowadays, even an offshore wind turbine with a complex support structure such as a jacket can be analysed. However, the computational effort rises significantly with an increasing level of details. This counts especially for offshore wind turbines with lattice support structures, since those models do naturally have a higher number of nodes and elements than simpler monopile structures. During the design process multiple load simulations are demanded to obtain an optimal solution. In the view of pre-design tasks it is crucial to apply load simulations which keep the simulation quality and the computational effort in balance. The paper will introduce a reference wind turbine model consisting of the REpower5M wind turbine and a jacket support structure with a high level of detail. In total twelve variations of this reference model are derived and presented. Main focus is to simplify the models of the support structure and the foundation. The reference model and the simplified models are simulated with the coupled simulation tool Flex5-Poseidon and analysed regarding frequencies, fatigue loads, and ultimate loads. A model has been found which reaches an adequate increase of simulation speed while holding the results in an acceptable range compared to the reference results.

46 CFR 107.211 - Original Certificate of Inspection.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Original Certificate of Inspection. 107.211 Section 107.211 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS... Offshore Drilling Units” (Appendix A). Existing structure, arrangements, materials, equipment, and...

46 CFR 107.211 - Original Certificate of Inspection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Original Certificate of Inspection. 107.211 Section 107.211 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS... Offshore Drilling Units” (Appendix A). Existing structure, arrangements, materials, equipment, and...

46 CFR 107.211 - Original Certificate of Inspection.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Original Certificate of Inspection. 107.211 Section 107.211 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS... Offshore Drilling Units” (Appendix A). Existing structure, arrangements, materials, equipment, and...

46 CFR 107.211 - Original Certificate of Inspection.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Original Certificate of Inspection. 107.211 Section 107.211 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS... Offshore Drilling Units” (Appendix A). Existing structure, arrangements, materials, equipment, and...

46 CFR 107.211 - Original Certificate of Inspection.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Original Certificate of Inspection. 107.211 Section 107.211 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS... Offshore Drilling Units” (Appendix A). Existing structure, arrangements, materials, equipment, and...

High-resolution computational algorithms for simulating offshore wind turbines and farms: Model development and validation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calderer, Antoni; Yang, Xiaolei; Angelidis, Dionysios

2015-10-30

The present project involves the development of modeling and analysis design tools for assessing offshore wind turbine technologies. The computational tools developed herein are able to resolve the effects of the coupled interaction of atmospheric turbulence and ocean waves on aerodynamic performance and structural stability and reliability of offshore wind turbines and farms. Laboratory scale experiments have been carried out to derive data sets for validating the computational models.

Arctic ice islands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sackinger, W.M.; Jeffries, M.O.; Lu, M.C.

1988-01-01

The development of offshore oil and gas resources in the Arctic waters of Alaska requires offshore structures which successfully resist the lateral forces due to moving, drifting ice. Ice islands are floating, a tabular icebergs, up to 60 meters thick, of solid ice throughout their thickness. The ice islands are thus regarded as the strongest ice features in the Arctic; fixed offshore structures which can directly withstand the impact of ice islands are possible but in some locations may be so expensive as to make oilfield development uneconomic. The resolution of the ice island problem requires two research steps: (1)more » calculation of the probability of interaction between an ice island and an offshore structure in a given region; and (2) if the probability if sufficiently large, then the study of possible interactions between ice island and structure, to discover mitigative measures to deal with the moving ice island. The ice island research conducted during the 1983-1988 interval, which is summarized in this report, was concerned with the first step. Monte Carlo simulations of ice island generation and movement suggest that ice island lifetimes range from 0 to 70 years, and that 85% of the lifetimes are less then 35 years. The simulation shows a mean value of 18 ice islands present at any time in the Arctic Ocean, with a 90% probability of less than 30 ice islands. At this time, approximately 34 ice islands are known, from observations, to exist in the Arctic Ocean, not including the 10-meter thick class of ice islands. Return interval plots from the simulation show that coastal zones of the Beaufort and Chukchi Seas, already leased for oil development, have ice island recurrences of 10 to 100 years. This implies that the ice island hazard must be considered thoroughly, and appropriate safety measures adopted, when offshore oil production plans are formulated for the Alaskan Arctic offshore. 132 refs., 161 figs., 17 tabs.« less

[Medical Emergency Preparedness in offshore wind farms : New challenges in the german north and baltic seas].

PubMed

Stuhr, M; Dethleff, D; Weinrich, N; Nielsen, M; Hory, D; Kowald, B; Seide, K; Kerner, T; Nau, C; Jürgens, C

2016-05-01

Offshore windfarms are constructed in the German North and Baltic Seas. The off-coast remoteness of the windfarms, particular environmental conditions, limitations in offshore structure access, working in heights and depths, and the vast extent of the offshore windfarms cause significant challenges for offshore rescue. Emergency response systems comparable to onshore procedures are not fully established yet. Further, rescue from offshore windfarms is not part of the duty of the German Maritime Search and Rescue Organization or SAR-Services due to statute and mandate reasons. Scientific recommendations or guidelines for rescue from offshore windfarms are not available yet. The present article reflects the current state of medical care and rescue from German offshore windfarms and related questions. The extended therapy-free interval until arrival of the rescue helicopter requires advanced first-aid measures as well as improved first-aider qualification. Rescue helicopters need to be equipped with a winch system in order to dispose rescue personnel on the wind turbines, and to hoist-up patients. For redundancy reasons and for conducting rendezvous procedures, adequate sea-bound rescue units need to be provided. In the light of experiences from the offshore oil and gas industry and first offshore wind analyses, the availability of professional medical personnel in offshore windfarms seems advisible. Operational air medical rescue services and specific offshore emergency reaction teams have established a powerful rescue chain. Besides the present development of medical standards, more studies are necessary in order to place the rescue chain on a long-term, evidence-based groundwork. A central medical offshore registry may help to make a significant contribution at this point.

New Insights on the Structure of the Cascadia Subduction Zone from Amphibious Seismic Data

NASA Astrophysics Data System (ADS)

Janiszewski, Helen Anne

A new onshore-offshore seismic dataset from the Cascadia subduction zone was used to characterize mantle lithosphere structure from the ridge to the volcanic arc, and plate interface structure offshore within the seismogenic zone. The Cascadia Initiative (CI) covered the Juan de Fuca plate offshore the northwest coast of the United States with an ocean bottom seismometer (OBS) array for four years; this was complemented by a simultaneous onshore seismic array. Teleseismic data recorded by this array allows the unprecedented imaging of an entire tectonic plate from its creation at the ridge through subduction initiation and back beyond the volcanic arc along the entire strike of the Cascadia subduction zone. Higher frequency active source seismic data also provides constraints on the crustal structure along the plate interface offshore. Two seismic datasets were used to image the plate interface structure along a line extending 100 km offshore central Washington. These are wide-angle reflections from ship-to-shore seismic data from the Ridge-To-Trench seismic cruise and receiver functions calculated from a densely spaced CI OBS focus array in a similar region. Active source seismic observations are consistent with reflections from the plate interface offshore indicating the presence of a P-wave velocity discontinuity. Until recently, there has been limited success in using the receiver function technique on OBS data. I avoid these traditional challenges by using OBS constructed with shielding deployed in shallow water on the continental shelf. These data have quieter horizontals and avoid water- and sediment-multiple contamination at the examined frequencies. The receiver functions are consistently modeled with a velocity structure that has a low velocity zone (LVZ) with elevated P to S-wave velocity ratios at the plate interface. A similar LVZ structure has been observed onshore and interpreted as a combination of elevated pore-fluid pressures or metasediments. This new offshore result indicates that the structure may persist updip indicating the plate interface may be weak. To focus more broadly on the entire subduction system, I calculate phase velocities from teleseismic Rayleigh waves from 20-100 s period across the entire onshore-offshore array. The shear-wave velocity model calculated from these data can provide constrains on the thermal structure of the lithosphere both prior to and during subduction of the Juan de Fuca plate. Using OBS data in this period band requires removal of tilt and compliance noise, two types of water-induced noise that affect long period data. To facilitate these corrections on large seismic arrays such as the CI, an automated quality control routine was developed for selecting noise windows for the calculation of the required transfer functions. These corrections typically involve either averaging out transient signals, which requires the assumption of stationarity of the noise over the long periods of time, or laborious hand selection of noise segments. This new method calculates transfer functions based on daily time series that exclude transient signals, but allows for the investigation of long-term variation over the course of an instrument's deployment. I interpret these new shoreline-crossing phase velocity maps in terms of the tectonics associated with the Cascadia subduction system. Major findings include that oceanic plate cooling models do not explain the velocities observed beneath the Juan de Fuca plate, that slow velocities in the forearc appear to be more prevalent in areas modeled to have experienced high slip in past Cascadia megathrust earthquakes, and along strike variations in phase velocity reflect variations in arc structure and backarc tectonics.

Moment tensor inversion of the 2016 southeast offshore Mie earthquake in the Tonankai region using a three-dimensional velocity structure model: effects of the accretionary prism and subducting oceanic plate

NASA Astrophysics Data System (ADS)

Takemura, Shunsuke; Kimura, Takeshi; Saito, Tatsuhiko; Kubo, Hisahiko; Shiomi, Katsuhiko

2018-03-01

The southeast offshore Mie earthquake occurred on April 1, 2016 near the rupture area of the 1944 Tonankai earthquake, where seismicity around the interface of the Philippine Sea plate had been very low until this earthquake. Since this earthquake occurred outside of seismic arrays, the focal mechanism and depth were not precisely constrained using a one-dimensional velocity model, as in a conventional approach. We conducted a moment tensor inversion of this earthquake by using a three-dimensional velocity structure model. Before the analysis of observed data, we investigated the effects of offshore heterogeneous structures such as the seawater, accretionary prism, and subducting oceanic plate by using synthetic seismograms in a full three-dimensional model and simpler models. The accretionary prism and subducting oceanic plate play important roles in the moment tensor inversion for offshore earthquakes in the subduction zone. Particularly, the accretionary prism, which controls the excitation and propagation of long-period surface waves around the offshore region, provides better estimations of the centroid depths and focal mechanisms of earthquakes around the Nankai subduction zone. The result of moment tensor inversion for the 2016 southeast offshore Mie earthquake revealed low-angle thrust faulting with a moment magnitude of 5.6. According to geophysical surveys in the Nankai Trough, our results suggest that the rupture of this earthquake occurred on the interface of the Philippine Sea plate, rather than on a mega-splay fault. Detailed comparisons of first-motion polarizations provided additional constraints of the rupture that occurred on the interface of the Philippine Sea plate.

Analysis of Tide and Offshore Storm-Induced Water Table Fluctuations for Structural Characterization of a Coastal Island Aquifer

NASA Astrophysics Data System (ADS)

Trglavcnik, Victoria; Morrow, Dean; Weber, Kela P.; Li, Ling; Robinson, Clare E.

2018-04-01

Analysis of water table fluctuations can provide important insight into the hydraulic properties and structure of a coastal aquifer system including the connectivity between the aquifer and ocean. This study presents an improved approach for characterizing a permeable heterogeneous coastal aquifer system through analysis of the propagation of the tidal signal, as well as offshore storm pulse signals through a coastal aquifer. Offshore storms produce high wave activity, but are not necessarily linked to significant onshore precipitation. In this study, we focused on offshore storm events during which no onshore precipitation occurred. Extensive groundwater level data collected on a sand barrier island (Sable Island, NS, Canada) show nonuniform discontinuous propagation of the tide and offshore storm pulse signals through the aquifer with isolated inland areas showing enhanced response to both oceanic forcing signals. Propagation analysis suggests that isolated inland water table fluctuations may be caused by localized leakage from a confined aquifer that is connected to the ocean offshore but within the wave setup zone. Two-dimensional groundwater flow simulations were conducted to test the leaky confined-unconfined aquifer conceptualization and to identify the effect of key parameters on tidal signal propagation in leaky confined-unconfined coastal aquifers. This study illustrates that analysis of offshore storm signal propagation, in addition to tidal signal propagation, provides a valuable and low resource approach for large-scale characterization of permeable heterogeneous coastal aquifers. Such an approach is needed for the effective management of coastal environments where water resources are threatened by human activities and the changing climate.

Geologic Assessment of Undiscovered Oil and Gas Resources of the North Cuba Basin, Cuba

USGS Publications Warehouse

Schenk, Christopher J.

2010-01-01

Petroleum generation in the North Cuba Basin is primarily the result of thrust loading of Jurassic and Cretaceous source rocks during formation of the North Cuba fold and thrust belt in the Late Cretaceous to Paleogene. The fold and thrust belt formed as Cuban arc-forearc rocks along the leading edge of the Caribbean plate translated northward during the opening of the Yucatan Basin and collided with the passive margin of southern North America in the Paleogene. Petroleum fluids generated during thrust loading migrated vertically into complex structures in the fold and thrust belt, into structures in the foreland basin, and possibly into carbonate reservoirs along the margins of the Yucatan and Bahama carbonate platforms. The U.S. Geological Survey (USGS) defined a Jurassic-Cretaceous Composite Total Petroleum System (TPS) and three assessment units (AU)-North Cuba Fold and Thrust Belt AU, North Cuba Foreland Basin AU, and the North Cuba Platform Margin Carbonate AU-within this TPS based mainly on structure and reservoir type (fig. 1). There is considerable geologic uncertainty as to the extent of petroleum migration that might have occurred within this TPS to form potential petroleum accumulations. Taking this geologic uncertainty into account, especially in the offshore area, the mean volumes of undiscovered resources in the composite TPS of the North Cuba Basin are estimated at (1) 4.6 billion barrels of oil (BBO), with means ranging from an F95 probability of 1 BBO to an F5 probability of 9 BBO; and (2) 8.6 trillion cubic feet of of gas (TCFG), of which 8.6 TCFG is associated with oil fields, and about 1.2 TCFG is in nonassociated gas fields in the North Cuba Foreland Basin AU.

Geological and technological assessment of artificial reef sites, Louisiana outer continental shelf

USGS Publications Warehouse

Pope, D.L.; Moslow, T.F.; Wagner, J.B.

1993-01-01

This paper describes the general procedures used to select sites for obsolete oil and gas platforms as artificial reefs on the Louisiana outer continental shelf (OCS). The methods employed incorporate six basic steps designed to resolve multiple-use conflicts that might otherwise arise with daily industry and commercial fishery operations, and to identify and assess both geological and technological constraints that could affect placement of the structures. These steps include: (1) exclusion mapping; (2) establishment of artificial reef planning areas; (3) database compilation; (4) assessment and interpretation of database; (5) mapping of geological and man-made features within each proposed reef site; and (6) site selection. Nautical charts, bathymetric maps, and offshore oil and gas maps were used for exclusion mapping, and to select nine regional planning areas. Pipeline maps were acquired from federal agencies and private industry to determine their general locations within each planning area, and to establish exclusion fairways along each pipeline route. Approximately 1600 line kilometers of high-resolution geophysical data collected by federal agencies and private industry was acquired for the nine planning areas. These data were interpreted to determine the nature and extent of near-surface geologic features that could affect placement of the structures. Seismic reflection patterns were also characterized to evaluate near-bottom sedimentation processes in the vicinity of each reef site. Geotechnical borings were used to determine the lithological and physical properties of the sediment, and for correlation with the geophysical data. Since 1987, five sites containing 10 obsolete production platforms have been selected on the Louisiana OCS using these procedures. Industry participants have realized a total savings of approximately US $1 500 000 in salvaging costs by converting these structures into artificial reefs. ?? 1993.

Horizontal variability of the marine boundary layer structure upwind of San Nicolas Island during FIRE, 1987

NASA Technical Reports Server (NTRS)

Jensen, Douglas R.

1990-01-01

During the months of June and July 1987, the Marine Stratocumulus Intensive Field Observation Experiment of First ISCCP Regional Experiment (FIRE) was conducted in the Southern California offshore area in the vicinity of San Nicolas Island (SNI). The Naval Ocean Systems Center (NOSC) airborne platform was utilized during FIRE to investigate the upwind low level horizontal variability of the marine boundary layer structure to determine the representativeness of SNI-based measurements to upwind open ocean conditions. The NOSC airborne meteorological platform made three flights during FIRE, two during clear sky conditions (19 and 23 July), and one during two stratus conditions (15 July). The boundary layer structure variations associated with the stratus clouds of 15 July 1987 are discussed. Profiles of air temperature (AT) and relative humidity (RH) taken 'at' and 'upwind' of SNI do show differences between the so-called open ocean conditions and those taken near the island. However, the observed difference cannot be uniquely identified to island effects, especially since the upwind fluctuations of AT and RH bound the SNI measurements. Total optical depths measures at SNI do not appear to be greatly affected by any surface based aerosol effects created by the island and could therefore realistically represent open ocean conditions. However, if one were to use the SNI aerosol measurements to predict ship to ship EO propagation conditions, significant errors could be introduced due to the increased number of surface aerosols observed near SNI which may not be, and were not, characteristic of open ocean conditions. Sea surface temperature measurements taken at the island will not, in general, represent those upwind open ocean conditions. Also, since CTT's varied appreciably along the upwind radials, measurements of CTT over the island may not be representative of actual open ocean CTT's.

Automatic control and monitoring equipment for cathodic protection of offshore structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, J.H.

1979-10-01

The preferred cathodic-protection systems for offshore structures are (1) the sacrificial-anode form for areas where the anode's weight or wave resistance is not a serious handicap and (2) a combined anode/impressed-current system that reduces the anode mass. Problems associated with controlling and monitoring the equipment are related to the anode locations, suitability of the reference electrodes, instrumentation requirements, interpretation of the measured potentials, and influence of water depth.

Development and Verification of the Soil-Pile Interaction Extension for SubDyn

DOE Office of Scientific and Technical Information (OSTI.GOV)

Damiani, Rick R; Wendt, Fabian F

SubDyn is the substructure structural-dynamics module for the aero-hydro-servo-elastic tool FAST v8. SubDyn uses a finite-element model (FEM) to simulate complex multimember lattice structures connected to conventional turbines and towers, and it can make use of the Craig-Bampton model reduction. Here we describe the newly added capability to handle soil-pile stiffness and compare results for monopile and jacket-based offshore wind turbines as obtained with FAST v8, SACS, and EDP (the latter two are modeling software packages commonly used in the offshore oil and gas industry). The level of agreement in terms of modal properties and loads for the entire offshoremore » wind turbine components is excellent, thus allowing SubDyn and FAST v8 to accurately simulate offshore wind turbines on fixed-bottom structures and accounting for the effect of soil dynamics, thus reducing risk to the project.« less

Metocean Data Needs Assessment for U.S. Offshore Wind Energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bailey, Bruce H.; Filippelli, Matthew; Baker, Matthew

2015-01-01

A potential barrier to developing offshore wind energy in the United States is the general lack of accurate information in most offshore areas about the wind resource characteristics and external metocean design conditions at the heights and depths relevant to wind turbines and their associated structures and components. Knowledge of these conditions enables specification of the appropriate design basis for wind turbine structures and components so they can withstand the loads expected over a project’s lifetime. Human safety, vessel navigation, and project construction and maintenance activities are equally tied to the metocean environment. Currently, metocean data is sparse in potentialmore » development areas and even when available, does not include the detail or quality required to make informed decisions.« less

Long-term changes in sediment barium inventories associated with drilling-related discharges in the Santa Maria Basin, California, USA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phillips, C.; Evans, J.; Hom, W.

1998-09-01

Nine-year (1986--1995) records of barium (Ba) concentrations in surficial, subsurface, and suspended sediments near offshore oil and gas platforms in the Santa Maria Basin, California, USA, were analyzed to evaluate temporal trends related to drilling activities. These trends provide important information on the long-term effects of drilling discharges on geochemical conditions. Drilling during the 1986 through 1989 (phase II) monitoring period resulted in significant changes in Ba concentrations in suspended particles and surficial sediments, whereas the relatively shorter 1993 through 1994 (phase III) drilling operations resulted in only minor increases in Ba concentrations in suspended sediments. Residual excess Ba wasmore » present in some sediments within 500 m of the platforms at concentrations up to an order of magnitude above background. These elevated levels probably were associated with cuttings particles deposited near the base of the platforms. Calculated excess Ba in sediments within 500 m of the platforms represented 6 to 11% of the total Ba discharged during the two drilling periods.« less

Characterization of the Hosgri Fault Zone and adjacent structures in the offshore Santa Maria Basin, south-central California: Chapter CC of Evolution of sedimentary basins/onshore oil and gas investigations - Santa Maria province

USGS Publications Warehouse

Willingham, C. Richard; Rietman, Jan D.; Heck, Ronald G.; Lettis, William R.

2013-01-01

The Hosgri Fault Zone trends subparallel to the south-central California coast for 110 km from north of Point Estero to south of Purisima Point and forms the eastern margin of the present offshore Santa Maria Basin. Knowledge of the attributes of the Hosgri Fault Zone is important for petroleum development, seismic engineering, and environmental planning in the region. Because it lies offshore along its entire reach, our characterizations of the Hosgri Fault Zone and adjacent structures are primarily based on the analysis of over 10,000 km of common-depth-point marine seismic reflection data collected from a 5,000-km2 area of the central and eastern parts of the offshore Santa Maria Basin. We describe and illustrate the along-strike and downdip geometry of the Hosgri Fault Zone over its entire length and provide examples of interpreted seismic reflection records and a map of the structural trends of the fault zone and adjacent structures in the eastern offshore Santa Maria Basin. The seismic data are integrated with offshore well and seafloor geologic data to describe the age and seismic appearance of offshore geologic units and marker horizons. We develop a basin-wide seismic velocity model for depth conversions and map three major unconformities along the eastern offshore Santa Maria Basin. Accompanying plates include maps that are also presented as figures in the report. Appendix A provides microfossil data from selected wells and appendix B includes uninterpreted copies of the annotated seismic record sections illustrated in the chapter. Features of the Hosgri Fault Zone documented in this investigation are suggestive of both lateral and reverse slip. Characteristics indicative of lateral slip include (1) the linear to curvilinear character of the mapped trace of the fault zone, (2) changes in structural trend along and across the fault zone that diminish in magnitude toward the ends of the fault zone, (3) localized compressional and extensional structures characteristic of constraining and releasing bends and stepovers, (4) changes in the sense and magnitude of vertical separation along strike within the fault zone, and (5) changes in downdip geometry between the major traces and segments of the fault zone. Characteristics indicative of reverse slip include (1) reverse fault geometries that occur across major strands of the fault zone and (2) fault-bend folds and localized thrust faults that occur along the northern and southern reaches of the fault. Analyses of high-resolution, subbottom profiler and side-scan sonar records indicate localized Holocene activity along most of the extent of the fault zone. Collectively, these features are the basis of our characterization of the Hosgri Fault Zone as an active, 110-km-long, convergent right-oblique slip (transpressional) fault with identified northern and southern terminations. This interpretation is consistent with recently published analyses of onshore geologic data, regional tectonic kinematic models, and instrumental seismicity.

Air emissions assessment from offshore oil activities in Sonda de Campeche, Mexico.

PubMed

Schifter, I; González-Macías, C; Miranda, A; López-Salinas, E

2005-10-01

Air emission data from offshore oil platforms, gas and oil processing installations and contribution of marine activities at the Sonda de Campeche, located at the Gulf of Mexico, were compiled and integrated to facilitate the study of long range transport of pollutants into the region. From this important region, roughly 76% of the total Mexican oil and gas production is obtained. It was estimated that the total air emissions of all contaminants are approximately 821,000 tons per year. Hydrocarbons are the largest pollutant emissions with 277,590 tons per year, generated during flaring activities, and SOx in second place with 185,907 tons per year. Marine and aviation activities contribute with less than 2% of total emissions. Mass of pollutants emitted per barrel of petroleum produced calculated in this work, are in the range reported by similar oil companies.

Comparison of numerical hindcasted severe waves with Doppler radar measurements in the North Sea

NASA Astrophysics Data System (ADS)

Ponce de León, Sonia; Bettencourt, João H.; Dias, Frederic

2017-01-01

Severe sea states in the North Sea present a challenge to wave forecasting systems and a threat to offshore installations such as oil and gas platforms and offshore wind farms. Here, we study the ability of a third-generation spectral wave model to reproduce winter sea states in the North Sea. Measured and modeled time series of integral wave parameters and directional wave spectra are compared for a 12-day period in the winter of 2013-2014 when successive severe storms moved across the North Atlantic and the North Sea. Records were obtained from a Doppler radar and wave buoys. The hindcast was performed with the WAVEWATCH III model (Tolman 2014) with high spectral resolution both in frequency and direction. A good general agreement was obtained for integrated parameters, but discrepancies were found to occur in spectral shapes.

Natural Offshore Oil Seepage and Related Tarball Accumulation on the California Coastline - Santa Barbara Channel and the Southern Santa Maria Basin: Source Identification and Inventory

USGS Publications Warehouse

Lorenson, T.D.; Hostettler, Frances D.; Rosenbauer, Robert J.; Peters, Kenneth E.; Dougherty, Jennifer A.; Kvenvolden, Keith A.; Gutmacher, Christina E.; Wong, Florence L.; Normark, William R.

2009-01-01

Oil spillage from natural sources is very common in the waters of southern California. Active oil extraction and shipping is occurring concurrently within the region and it is of great interest to resource managers to be able to distinguish between natural seepage and anthropogenic oil spillage. The major goal of this study was to establish the geologic setting, sources, and ultimate dispersal of natural oil seeps in the offshore southern Santa Maria Basin and Santa Barbara Basins. Our surveys focused on likely areas of hydrocarbon seepage that are known to occur between Point Arguello and Ventura, California. Our approach was to 1) document the locations and geochemically fingerprint natural seep oils or tar; 2) geochemically fingerprint coastal tar residues and potential tar sources in this region, both onshore and offshore; 3) establish chemical correlations between offshore active seeps and coastal residues thus linking seep sources to oil residues; 4) measure the rate of natural seepage of individual seeps and attempt to assess regional natural oil and gas seepage rates; and 5) interpret the petroleum system history for the natural seeps. To document the location of sub-sea oil seeps, we first looked into previous studies within and near our survey area. We measured the concentration of methane gas in the water column in areas of reported seepage and found numerous gas plumes and measured high concentrations of methane in the water column. The result of this work showed that the seeps were widely distributed between Point Conception east to the vicinity of Coal Oil Point, and that they by in large occur within the 3-mile limit of California State waters. Subsequent cruises used sidescan and high resolution seismic to map the seafloor, from just south of Point Arguello, east to near Gaviota, California. The results of the methane survey guided the exploration of the area west of Point Conception east to Gaviota using a combination of seismic instruments. The seafloor was mapped by sidescan sonar, and numerous lines of high -resolution seismic surveys were conducted over areas of interest. Biomarker and stable carbon isotope ratios were used to infer the age, lithology, organic matter input, and depositional environment of the source rocks for 388 samples of produced crude oil, seep oil, and tarballs mainly from coastal California. These samples were used to construct a chemometric fingerprint (multivariate statistics) decision tree to classify 288 additional samples, including tarballs of unknown origin collected from Monterey and San Mateo County beaches after a storm in early 2007. A subset of 9 of 23 active offshore platform oils and one inactive platform oil representing a few oil reservoirs from the western Santa Barbara Channel were used in this analysis, and thus this model is not comprehensive and the findings are not conclusive. The platform oils included in this study are from west to east: Irene, Hildago, Harvest, Hermosa, Heritage, Harmony, Hondo, Holly, Platform A, and Hilda (now removed). The results identify three 'tribes' of 13C-rich oil samples inferred to originate from thermally mature equivalents of the clayey-siliceous, carbonaceous marl, and lower calcareous-siliceous members of the Monterey Formation. Tribe 1 contains four oil families having geochemical traits of clay-rich marine shale source rock deposited under suboxic conditions with substantial higher-plant input. Tribe 2 contains four oil families with intermediate traits, except for abundant 28,30-bisnorhopane, indicating suboxic to anoxic marine marl source rock with hemipelagic input. Tribe 3 contains five oil families with traits of distal marine carbonate source rock deposited under anoxic conditions with pelagic but little or no higher-plant input. Tribes 1 and 2 occur mainly south of Point Conception in paleogeographic settings where deep burial of the Monterey Formation source rock favored generation from all thre

Healthy offshore workforce? A qualitative study on offshore wind employees' occupational strain, health, and coping.

PubMed

Mette, Janika; Velasco Garrido, Marcial; Harth, Volker; Preisser, Alexandra M; Mache, Stefanie

2018-01-23

Offshore work has been described as demanding and stressful. Despite this, evidence regarding the occupational strain, health, and coping behaviors of workers in the growing offshore wind industry in Germany is still limited. The purpose of our study was to explore offshore wind employees' perceptions of occupational strain and health, and to investigate their strategies for dealing with the demands of offshore work. We conducted 21 semi-structured telephone interviews with employees in the German offshore wind industry. The interviews were transcribed and analyzed in a deductive-inductive approach following Mayring's qualitative content analysis. Workers generally reported good mental and physical health. However, they also stated perceptions of stress at work, fatigue, difficulties detaching from work, and sleeping problems, all to varying extents. In addition, physical health impairment in relation to offshore work, e.g. musculoskeletal and gastrointestinal complaints, was documented. Employees described different strategies for coping with their job demands. The strategies comprised of both problem and emotion-focused approaches, and were classified as either work-related, health-related, or related to seeking social support. Our study is the first to investigate the occupational strain, health, and coping of workers in the expanding German offshore wind industry. The results offer new insights that can be utilized for future research in this field. In terms of practical implications, the findings suggest that measures should be carried out aimed at reducing occupational strain and health impairment among offshore wind workers. In addition, interventions should be initiated that foster offshore wind workers' health and empower them to further expand on effective coping strategies at their workplace.

"It's still a great adventure" - exploring offshore employees' working conditions in a qualitative study.

PubMed

Mette, Janika; Velasco Garrido, Marcial; Harth, Volker; Preisser, Alexandra M; Mache, Stefanie

2017-01-01

Despite the particular demands inherent to offshore work, little is known about the working conditions of employees in the German offshore wind industry. To date, neither offshore employees' job demands and resources, nor their needs for improving the working conditions have been explored. Therefore, the aim of this study was to conduct a qualitative analysis to gain further insight into these topics. Forty-two semi-structured telephone interviews with German offshore employees ( n  = 21) and offshore experts ( n  = 21) were conducted. Employees and experts were interviewed with regard to their perceptions of their working conditions offshore. In addition, employees were asked to identify areas with potential need for improvement. The interviews were analysed in a deductive-inductive process according to Mayring's qualitative content analysis. Employees and experts reported various demands of offshore work, including challenging physical labour, long shifts, inactive waiting times, and recurrent absences from home. In contrast, the high personal meaning of the work, regular work schedule (14 days offshore, 14 days onshore), and strong comradeship were highlighted as job resources. Interviewees' working conditions varied considerably, e.g. regarding their work tasks and accommodations. Most of the job demands were perceived in terms of the work organization and living conditions offshore. Likewise, employees expressed the majority of needs for improvement in these areas. Our study offers important insight into the working conditions of employees in the German offshore wind industry. The results can provide a basis for further quantitative research in order to generalize the findings. Moreover, they can be utilized to develop needs-based interventions to improve the working conditions offshore.

Extensional Tectonics and Sedimentary Architecture Using 3-D Seismic Data: An Example from Hydrocarbon-Bearing Mumbai Offshore Basin, West Coast of India

NASA Astrophysics Data System (ADS)

Mukhopadhyay, D. K.; Bhowmick, P. K.; Mishra, P.

2016-12-01

In offshore sedimentary basins, analysis of 3-D seismic data tied with well log data can be used to deduce robust isopach and structure contour maps of different stratigraphic formations. The isopach maps give depocenters whereas structure contour maps give structural relief at a specific time. Combination of these two types of data helps us decipher horst-graben structures, sedimentary basin architecture and tectono-stratigraphic relations through Tertiary time. Restoration of structural cross sections with back-stripping of successively older stratigraphic layers leads to better understand tectono-sedimentary evolution of a basin. The Mumbai (or Bombay) Offshore Basin is the largest basin off the west coast of India and includes Bombay High giant oil/gas field. Although this field was discovered in 1974 and still producing, the basin architecture vis-à-vis structural evolution are not well documented. We take the approach briefly outlined above to study in detail three large hydrocarbon-bearing structures located within the offshore basin. The Cretaceous Deccan basalt forms the basement and hosts prodigal thickness (> 8 km at some localities) of Tertiary sedimentary formations.A two stage deformation is envisaged. At the first stage horst and graben structures formed due to approximately E-W extensional tectonics. This is most spectacularly seen at the basement top level. The faults associated with this extension strike NNW. At the second stage of deformation a set of ENE-striking cross faults have developed leading to the formation of transpressional structures at places. High rate of early sedimentation obliterated horst-graben architecture to large extent. An interesting aspect emerges is that the all the large-scale structures have rather low structural relief. However, the areal extent of such structures are very large. Consequently, these structures hold commercial quantities of oil/gas.

Deposition model of a Miocene barred wave- and storm-dominated shoreface and shelf, southeastern Malay basin, offshore west Malaysia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramli, N.

1986-01-01

The J sandstone is an important hydrocarbon-bearing reservoir in the southeastern part of the Malay basin. The lower and upper members of the J sandstone are composed of shoreface and offshore sediments. The shoreface sequence contains depositional structures characteristic of a barred wave- and storm-dominated shoreface. Each shoreface sequence is laterally associated with a series of stacked offshore bars. Offshore bars can be subdivided into proximal and distal types. Two types of proximal offshore bars have been identified: (1) proximal bars formed largely above fair-weather wave base (inner proximal bars), and (2) proximal bars formed below fair-weather wave base (outermore » proximal bars). The inner proximal bars are closely associated with the shoreface sequence and are similar to the middle and lower shoreface. The presence of poorly sorted, polymodal, very fine to very coarse-grained sandstone beneath well-sorted crestal sandstones of inner proximal bars suggests that these offshore bars may have been deposited rapidly by storms. The crests of the inner proximal offshore bars were subsequently reworked by fair-weather processes, and the crests of the outer proximal and distal offshore bars were reworked by waning storm currents and oscillatory waves. Thick marine shales overlying offshore bars contain isolated sheet sandstones. Each sheet sandstone exhibits features that may be characteristic of distal storm shelf deposits. 15 figures, 2 tables.« less

Microbes and mass extinctions: paleoenvironmental distribution of microbialites during times of biotic crisis.

PubMed

Mata, S A; Bottjer, D J

2012-01-01

Widespread development of microbialites characterizes the substrate and ecological response during the aftermath of two of the 'big five' mass extinctions of the Phanerozoic. This study reviews the microbial response recorded by macroscopic microbial structures to these events to examine how extinction mechanism may be linked to the style of microbialite development. Two main styles of response are recognized: (i) the expansion of microbialites into environments not previously occupied during the pre-extinction interval and (ii) increases in microbialite abundance and attainment of ecological dominance within environments occupied prior to the extinction. The Late Devonian biotic crisis contributed toward the decimation of platform margin reef taxa and was followed by increases in microbialite abundance in Famennian and earliest Carboniferous platform interior, margin, and slope settings. The end-Permian event records the suppression of infaunal activity and an elimination of metazoan-dominated reefs. The aftermath of this mass extinction is characterized by the expansion of microbialites into new environments including offshore and nearshore ramp, platform interior, and slope settings. The mass extinctions at the end of the Triassic and Cretaceous have not yet been associated with a macroscopic microbial response, although one has been suggested for the end-Ordovician event. The case for microbialites behaving as 'disaster forms' in the aftermath of mass extinctions accurately describes the response following the Late Devonian and end-Permian events, and this may be because each is marked by the reduction of reef communities in addition to a suppression of bioturbation related to the development of shallow-water anoxia. © 2011 Blackwell Publishing Ltd.

Simplified Technique for Predicting Offshore Pipeline Expansion

NASA Astrophysics Data System (ADS)

Seo, J. H.; Kim, D. K.; Choi, H. S.; Yu, S. Y.; Park, K. S.

2018-06-01

In this study, we propose a method for estimating the amount of expansion that occurs in subsea pipelines, which could be applied in the design of robust structures that transport oil and gas from offshore wells. We begin with a literature review and general discussion of existing estimation methods and terminologies with respect to subsea pipelines. Due to the effects of high pressure and high temperature, the production of fluid from offshore wells is typically caused by physical deformation of subsea structures, e.g., expansion and contraction during the transportation process. In severe cases, vertical and lateral buckling occurs, which causes a significant negative impact on structural safety, and which is related to on-bottom stability, free-span, structural collapse, and many other factors. In addition, these factors may affect the production rate with respect to flow assurance, wax, and hydration, to name a few. In this study, we developed a simple and efficient method for generating a reliable pipe expansion design in the early stage, which can lead to savings in both cost and computation time. As such, in this paper, we propose an applicable diagram, which we call the standard dimensionless ratio (SDR) versus virtual anchor length (L A ) diagram, that utilizes an efficient procedure for estimating subsea pipeline expansion based on applied reliable scenarios. With this user guideline, offshore pipeline structural designers can reliably determine the amount of subsea pipeline expansion and the obtained results will also be useful for the installation, design, and maintenance of the subsea pipeline.

Characterizing Methane Emissions at Local Scales with a 20 Year Total Hydrocarbon Time Series, Imaging Spectrometry, and Web Facilitated Analysis

NASA Astrophysics Data System (ADS)

Bradley, Eliza Swan

Methane is an important greenhouse gas for which uncertainty in local emission strengths necessitates improved source characterizations. Although CH4 plume mapping did not motivate the NASA Airborne Visible InfraRed Imaging Spectrometer (AVIRIS) design and municipal air quality monitoring stations were not intended for studying marine geological seepage, these assets have capabilities that can make them viable for studying concentrated (high flux, highly heterogeneous) CH4 sources, such as the Coal Oil Point (COP) seep field (˜0.015 Tg CH4 yr-1) offshore Santa Barbara, California. Hourly total hydrocarbon (THC) data, spanning 1990 to 2008 from an air pollution station located near COP, were analyzed and showed geologic CH4 emissions as the dominant local source. A band ratio approach was developed and applied to high glint AVIRIS data over COP, resulting in local-scale mapping of natural atmospheric CH4 plumes. A Cluster-Tuned Matched Filter (CTMF) technique was applied to Gulf of Mexico AVIRIS data to detect CH4 venting from offshore platforms. Review of 744 platform-centered CTMF subsets was facilitated through a flexible PHP-based web portal. This dissertation demonstrates the value of investigating municipal air quality data and imaging spectrometry for gathering insight into concentrated methane source emissions and highlights how flexible web-based solutions can help facilitate remote sensing research.

Vertical Deformation of Late Quaternary Features Across Port-au-Prince Bay, Haiti

NASA Astrophysics Data System (ADS)

Cormier, M.; McHugh, C. M.; Gulick, S. P.; Braudy, N.; Davis, M. B.; Diebold, J. B.; Dieudonne, N.; Douilly, R.; Hornbach, M. J.; Johnson, H. E.; Mishkin, K.; Seeber, L.; Sorlien, C. C.; Steckler, M. S.; Symithe, S. J.; Templeton, J.

2010-12-01

As part of a project that investigated the underwater impacts of the January 12, 2010 earthquake in Haiti, we surveyed offshore structures that may have been activated during that earthquake or that might become activated in future earthquakes. Part of that survey focused on the shallow shelf area that extends north of the segment of the Enriquillo-Plantain Garden fault that just ruptured. This area is occupied by an elongated depression, 25 km long, 10 km wide, and 140 m deep. The NW-SE axis of that shallow basin is sub-parallel to that of the NW-SE anticlines that bounds Port-au-Prince Bay. The shallow basin is also rimmed by a carbonate platform that is 5-10 km-wide and ~30m deep. New multibeam bathymetric and sidescan sonar data collected across that platform highlight a series of circular dissolution structures 1-2 km across and ~80 m deep. We interpret that morphology to indicate antecedent karst topography that developed during previous glacial maxima. According to that scenario, the shallow basin off Port-au-Prince would have been isolated from the Caribbean Sea by the continuous platform, and would probably have been occupied by a lagoon. Indeed, a few high-resolution chirp profiles image what may be a paleoshoreline at about 80m depth, buried beneath a 5-8 m thick, acoustically transparent, presumably Holocene layer. Preliminary analysis indicates that the basin floor and the base of the presumably Holocene layer are perfectly horizontal in the center of the basin, but tilted down to the south at its northern edge. The presumed paleoshoreline is also shallower to the north of the basin. We propose that this tilt is driven by contraction across the NW-SE fold-and-thrust belt that runs across Hispaniola. This hypothesis remains to be tested with a more thorough geophysical and coring survey in Port-au-Prince Bay.

Characterization of H/V Spectral Ratios for the Assessment of Slope Stability in the Gas Hydrate-rich Area: an Example from Offshore SW Taiwan

NASA Astrophysics Data System (ADS)

Lin, J. Y.; Tsia, C. H.; Cheng, W. B.; Chin, S. J.; Lin, S. S.; Liang, C. W.

2015-12-01

The Nakamura's method, which calculates the ratios between horizontal and vertical component spectra of seismic signals (H/V), is widely used in the inland area. However, few related estimations were performed for the offshore area and little knowledge for the marine sediments were obtained. From 2013 to 2015, three passive ocean bottom seismometer (OBS) experiments were conducted in gas hydrate-rich area offshore SW Taiwan in the aim of acquiring information related to the physical properties of seafloor sediments. The H/V of the seafloor sediments in the three areas were estimated by using the ambient noise and seismic signal recorded by OBSs. The resonance frequency of each site was estimated from the main peak of H/V distribution and a range between 5 and 10 Hz were obtained. Based on the empirical law, this resonance frequency range should correspond to a sediment thickness of approximately several to ten of meters. This estimation is consistent with the thickness of the sedimentary cover imaged by chirp sonar survey, suggesting that the site response of seafloor is dominantly controlled by the unconsolidated sedimentary layer on the top of the sea bed. Remarkably, the H/V ratios obtained in our study area are much larger than that calculated for the inland areas. The magnification can reach as high as 50 to more than 100. This observation infers that the sea water movement might emphasize the horizontal motion of the marine sediments, which is crucial for the slope stability assessment. Moreover, for most stations located in the active margin, no distinct peak is observed for the H/V pattern calculated during earthquakes. However, in the passive margin, the H/V peak calculated from ambient noise and earthquakes is mostly identical. This phenomenon may suggest that relatively unclear sedimentary boundary exist in the active margin environment. Estimating H/V spectral ratios of data recorded by the OBSs deployed in the southwest Taiwan offshore area offers a general understanding of the preferential vibration modes of seafloor sediment systems. By comparing the resonance characteristics of each site and the chirp sonar profiles, we hope to provide precious information for the designing of marine structures such as oil drilling and production platforms.

Seismic and Gravity Data Help Constrain the Stratigraphic and Tectonic History of Offshore New Harbor, Ross Sea, Antarctica

NASA Astrophysics Data System (ADS)

Speece, M. A.; Pekar, S. F.; Wilson, G. S.; Sunwall, D. A.; Tinto, K. J.

2010-12-01

The ANDRILL (ANtarctic geological DRILLing) Program’s Offshore New Harbor (ONH) Project successfully conducted multi-channel seismic and gravity surveys in 2008 to investigate the stratigraphic and tectonic history of westernmost Southern McMurdo Sound, Ross Sea, Antarctica, during the Greenhouse World (Eocene) into the start of the Icehouse World (Oligocene). Approximately 48 km of multi-channel seismic reflection data were collected on a sea-ice platform east of New Harbor. The seismic survey used and improved upon methods employed successfully by ANDRILL’s surveys in Southern McMurdo Sound (2005) and in Mackay Sea Valley (2007). These methods include using an air gun and snow streamer of gimbaled geophones. Upgrades in the ONH project’s field equipment substantially increased the rate at which seismic data could be acquired in a sea-ice environment compared to all previous surveys. In addition to the seismic survey, gravity data were collected from the sea ice in New Harbor with the aim of defining basin structural controls. Both the seismic and gravity data indicate thick sediment accumulation above the hanging wall of a major range front fault. This clearly identified fault could be the postulated master fault of the Transantarctic Mountains. An approximately 5 km thick sequence of sediments is present east of the CIROS-1 drill hole. CIROS-1 was drilled adjacent to the range front fault and recovered 702 m of sediments that cross the Eocene/Oligocene boundary. The new geophysical data indicate that substantial sediment core below the Eocene/Oligocene boundary could be recovered to the east of CIROS-1 during future drilling. Inshore of the range front fault, the data show fault bounded half grabens with sediment fill thickening eastward against localized normal faults. Modeling of the gravity data, that extends farther inland than the seismic profiles, suggests that over 1 km of sediments could be present locally offshore Taylor Valley. Future drilling of offshore Taylor Valley could help to constrain the East Antarctic Ice Sheet’s contributions to glacial-interglacial cyclicity in southern McMurdo Sound as far back as the middle Miocene. Unfortunately, the 2008 ONH seismic profiles do not extend far enough up Taylor Valley or Ferrar Fjord to fully define drilling targets. As a result, valley parallel seismic profiles are proposed to extend our seismic interpretations inland and substantiate the gravity models.

Offshore Wind Energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Strach-Sonsalla, Mareike; Stammler, Matthias; Wenske, Jan

In 1991, the Vindeby Offshore Wind Farm, the first offshore wind farm in the world, started feeding electricity to the grid off the coast of Lolland, Denmark. Since then, offshore wind energy has developed from this early experiment to a multibillion dollar market and an important pillar of worldwide renewable energy production. Unit sizes grew from 450 kW at Vindeby to the 7.5 MW-class offshore wind turbines (OWT ) that are currently (by October 2014) in the prototyping phase. This chapter gives an overview of the state of the art in offshore wind turbine (OWT) technology and introduces the principlesmore » of modeling and simulating an OWT. The OWT components -- including the rotor, nacelle, support structure, control system, and power electronics -- are introduced, and current technological challenges are presented. The OWT system dynamics and the environment (wind and ocean waves) are described from the perspective of OWT modelers and designers. Finally, an outlook on future technology is provided. The descriptions in this chapter are focused on a single OWT -- more precisely, a horizontal-axis wind turbine -- as a dynamic system. Offshore wind farms and wind farm effects are not described in detail in this chapter, but an introduction and further references are given.« less

OC5 Project Phase Ib: Validation of hydrodynamic loading on a fixed, flexible cylinder for offshore wind applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robertson, Amy N.; Wendt, Fabian; Jonkman, Jason M.

This paper summarizes the findings from Phase Ib of the Offshore Code Comparison, Collaboration, Continued with Correlation (OC5) project. OC5 is a project run under the International Energy Agency (IEA) Wind Research Task 30, and is focused on validating the tools used for modelling offshore wind systems through the comparison of simulated responses of select offshore wind systems (and components) to physical test data. For Phase Ib of the project, simulated hydrodynamic loads on a flexible cylinder fixed to a sloped bed were validated against test measurements made in the shallow water basin at the Danish Hydraulic Institute (DHI) withmore » support from the Technical University of Denmark (DTU). The first phase of OC5 examined two simple cylinder structures (Phase Ia and Ib) to focus on validation of hydrodynamic models used in the various tools before moving on to more complex offshore wind systems and the associated coupled physics. As a result, verification and validation activities such as these lead to improvement of offshore wind modelling tools, which will enable the development of more innovative and cost-effective offshore wind designs.« less

OC5 Project Phase Ib: Validation of hydrodynamic loading on a fixed, flexible cylinder for offshore wind applications

DOE PAGES

Robertson, Amy N.; Wendt, Fabian; Jonkman, Jason M.; ...

2016-10-13

This paper summarizes the findings from Phase Ib of the Offshore Code Comparison, Collaboration, Continued with Correlation (OC5) project. OC5 is a project run under the International Energy Agency (IEA) Wind Research Task 30, and is focused on validating the tools used for modelling offshore wind systems through the comparison of simulated responses of select offshore wind systems (and components) to physical test data. For Phase Ib of the project, simulated hydrodynamic loads on a flexible cylinder fixed to a sloped bed were validated against test measurements made in the shallow water basin at the Danish Hydraulic Institute (DHI) withmore » support from the Technical University of Denmark (DTU). The first phase of OC5 examined two simple cylinder structures (Phase Ia and Ib) to focus on validation of hydrodynamic models used in the various tools before moving on to more complex offshore wind systems and the associated coupled physics. As a result, verification and validation activities such as these lead to improvement of offshore wind modelling tools, which will enable the development of more innovative and cost-effective offshore wind designs.« less

Offshore remote sensing of the ocean by stereo vision systems

NASA Astrophysics Data System (ADS)

Gallego, Guillermo; Shih, Ping-Chang; Benetazzo, Alvise; Yezzi, Anthony; Fedele, Francesco

2014-05-01

In recent years, remote sensing imaging systems for the measurement of oceanic sea states have attracted renovated attention. Imaging technology is economical, non-invasive and enables a better understanding of the space-time dynamics of ocean waves over an area rather than at selected point locations of previous monitoring methods (buoys, wave gauges, etc.). We present recent progress in space-time measurement of ocean waves using stereo vision systems on offshore platforms, which focus on sea states with wavelengths in the range of 0.01 m to 1 m. Both traditional disparity-based systems and modern elevation-based ones are presented in a variational optimization framework: the main idea is to pose the stereoscopic reconstruction problem of the surface of the ocean in a variational setting and design an energy functional whose minimizer is the desired temporal sequence of wave heights. The functional combines photometric observations as well as spatial and temporal smoothness priors. Disparity methods estimate the disparity between images as an intermediate step toward retrieving the depth of the waves with respect to the cameras, whereas elevation methods estimate the ocean surface displacements directly in 3-D space. Both techniques are used to measure ocean waves from real data collected at offshore platforms in the Black Sea (Crimean Peninsula, Ukraine) and the Northern Adriatic Sea (Venice coast, Italy). Then, the statistical and spectral properties of the resulting oberved waves are analyzed. We show the advantages and disadvantages of the presented stereo vision systems and discuss furure lines of research to improve their performance in critical issues such as the robustness of the camera calibration in spite of undesired variations of the camera parameters or the processing time that it takes to retrieve ocean wave measurements from the stereo videos, which are very large datasets that need to be processed efficiently to be of practical usage. Multiresolution and short-time approaches would improve efficiency and scalability of the techniques so that wave displacements are obtained in feasible times.

Meals on Wheels? A Decade of Megafaunal Visual and Acoustic Observations from Offshore Oil & Gas Rigs and Platforms in the North and Irish Seas

PubMed Central

Todd, Victoria Louise Georgia; Todd, Ian Boyer

2016-01-01

A decade of visual and acoustic detections of marine megafauna around offshore Oil & Gas (O&G) installations in the North and Irish Seas are presented. Marine megafauna activity was monitored visually and acoustically by Joint Nature Conservation Committee (JNCC) qualified and experienced Marine Mammal Observers (MMO) and Passive Acoustic Monitoring (PAM) Operators respectively, with real-time towed PAM in combination with industry standard software, PAMGuard. Monitoring was performed during routine O&G industrial operations for underwater noise mitigation purposes, and to ensure adherence to regulatory guidelines. Incidental sightings by off-effort MMOs and installation crew were also reported. Visual and acoustic monitoring spanned 55 non-consecutive days between 2004 and 2014. A total of 47 marine mammal sightings were recorded by MMOs on dedicated watch, and 10 incidental sightings of marine megafauna were reported over 10 years. Species included: harbour porpoise (Phocoena phocoena), Atlantic white-sided dolphin (Lagenorhynchus acutus), white beaked dolphin (Lagenorhynchus albirostris), common dolphin (Delphinus delphis), minke whale (Balaenoptera acutorostrata), common seal (Phoca vitulina), grey seal (Halichoerus grypus) and, basking shark (Cetorhinus maximus). Passive Acoustic Monitoring was conducted on two occasions in 2014; 160 PAM hours over 12 days recorded a total of 308 individual clicks identified as harbour porpoises. These appear to be the first such acoustic detections obtained from a North Sea drilling rig whilst using a typically configured hydrophone array designed for towing in combination with real-time PAMGuard software. This study provides evidence that marine megafauna are present around mobile and stationary offshore O&G installations during routine operational activities. On this basis, Environmental Impact Assessments (EIAs) for decommissioning O&G platforms should be carried-out on a case-by-case basis, and must include provisions for hitherto overlooked marine megafauna. PMID:27078153

Gulf of Mexico Air/Sea Interaction: Measurements and Initial Data Characterization

NASA Astrophysics Data System (ADS)

MacDonald, C.; Huang, C. H.; Roberts, P. T.; Bariteau, L.; Fairall, C. W.; Gibson, W.; Ray, A.

2011-12-01

Corporate, government, and university researchers collaborated to develop an atmospheric boundary layer environmental observations program on an offshore platform in the Gulf of Mexico. The primary goals of this project were to provide data to (1) improve our understanding of boundary layer processes and air-sea interaction over the Gulf of Mexico; (2) improve regional-scale meteorological and air quality modeling; and (3) provide a framework for advanced offshore measurements to support future needs such as emergency response, exploration and lease decisions, wind energy research and development, and meteorological and air quality forecasting. In October 2010, meteorological and oceanographic sensors were deployed for an extended period (approximately 12 months) on a Chevron service platform (ST 52B, 90.5W, 29N) to collect boundary layer and sea surface data sufficient to support these objectives. This project has significant importance given the large industrial presence in the Gulf, sizeable regional population nearby, and the recognized need for precise and timely pollutant forecasts. Observations from this project include surface meteorology; sodar marine boundary layer winds; microwave radiometer profiles of temperature, relative humidity, and liquid water; ceilometer cloud base heights; water temperature and current profiles; sea surface temperature; wave height statistics; downwelling solar and infrared radiation; and air-sea turbulent momentum and heat fluxes. This project resulted in the collection of an unprecedented set of boundary layer measurements over the Gulf of Mexico that capture the range of meteorological and oceanographic interactions and processes that occur over an entire year. This presentation will provide insight into the logistical and scientific issues associated with the deployment and operations of unique measurements in offshore areas and provide results from an initial data analysis of boundary layer processes over the Gulf of Mexico, with a special focus on the relationship among measured and modeled energy fluxes and other oceanographic and atmospheric conditions.

U.S. Geological Survey program of offshore resource and geoenvironmental studies, Atlantic-Gulf of Mexico region, from September 1, 1976, to December 31, 1978

USGS Publications Warehouse

Folger, David W.; Needell, Sally W.

1983-01-01

Mineral and energy resources of the continental margins of the United States arc important to the Nation's commodity independence and to its balance of payments. These resources are being studied along the continental margins of the Atlantic Ocean and the Gulf of Mexico in keeping with the mission of the U.S. Geological Survey to survey the geologic structures, mineral resources, and products of the national domain.'(Organic Act of 1879). An essential corollary to these resource studies is the study of potential geologic hazards that may be associated with offshore resource exploration and exploitation. In cooperation with the U.S. Bureau of Land Management, the Geological Survey, through its Atlantic-Gulf of Mexico Marine Geology Program, carries out extensive research to evaluate hazards from sediment mobility, shallow gas, and slumping and to acquire information on the distribution and concentration of trace metals and biogenic and petroleum-derived hydrocarbons in sea-floor sediments. All these studies arc providing needed background information, including information on pollutant dispersal, on the nearshore, estuarine, and lacustrine areas that may be near pipeline and nuclear powerplant sites. Users of these data include the Congress, many Federal agencies, the coastal States, private industry, academia, and the concerned public. The results of the regional structural, stratigraphic, and resource studies carried out under the Atlantic-Gulf of Mexico Marine Geology Program have been used by the Geological Survey and the Bureau of Land Management to select areas for future leasing and to aid in the evaluation of tracts nominated for leasing. Resource studies have concentrated mostly on the Atlantic Outer Continental Shelf frontier areas. Geologic detailing of five major basins along the U.S. Atlantic margin, where sediments are as much as 14 km thick, have been revealed by 25,000 km of 24-and 48-channel common-depth-point seismic data, 187,000 km of acromagnetic data, and 39,000 km of gravity data, plus 10,000 samples and logs obtained from U.S. Geological Survey and industry drilling (for example, coreholes of the Atlantic Slope Program, Joint Oceanographic Institutions Deep Earth Sampling, Continental Offshore Stratigraphic Tests, and the Atlantic Margin Coring Program). A sedimentary section of Jurassic and Cretaceous age grades from terrigenous clastic rocks nearshore to carbonate rocks offshore; this section is part of an extensive buried bank-platform complex that could contain large reserves of natural gas and oil. The volume of sediment deposited offshore far exceeds the volume deposited onshore where extensive accumulations of oil, gas, and minerals have been found. Commercial exploratory drilling offshore thus far has been limited to the Baltimore Canyon Trough area off New Jersey, where at least two holes have found gas; leasing has taken place in the Southeast Georgia Embayment, where drilling was scheduled to begin in 1979, and is imminent in the Georges Bank area off New England. In addition, hydrogeologic and hydrochemical data obtained from the drilling studies have delineated freshwater-bearing submarine extensions of land aquifers that are important coastal ground-water resources. Hazards in the Georges Bank area include sand mobility associated with strong currents and storm-driven waves; high concentrations of suspended sediment in the water column that, when mixed with spilled oil, may sink to the bottom; and slumping along the upper slope. In the Baltimore Canyon, high sediment mobility accompanies major winter storms, and slumped material may cover as much as 20 percent of the upper slope. Potentially unstable slope areas are being studied in great detail to provide data on timing, triggering mechanisms, and rates of sediment movement. In the Southeast Georgia Embayment and Blake Plateau Basin, strong Gulf Stream flow poses a major problem to all offshore operations. In the Gulf o

Offshore rectenna feasbility

NASA Technical Reports Server (NTRS)

Freeman, J. W.; Hervey, D.; Glaser, P.

1980-01-01

A preliminary study of the feasibility and cost of an offshore rectenna to serve the upper metropolitan east coast was performed. A candidate site at which to build a 5 GW rectenna was selected on the basis of proximity to load centers, avoidance of shipping lanes, sea floor terrain, and relocated conditions. Several types of support structures were selected for study based initially on the reference system rectenna concept of a wire mesh ground screen and dipoles each with its own rectifier and filter circuits. Possible secondary uses of an offshore rectenna were examined and are evaluated.

Development of High Heat Input Welding Offshore Steel as Normalized Condition

NASA Astrophysics Data System (ADS)

Deng, Wei; Qin, Xiaomei

The heavy plate used for offshore structure is one of the important strategic products. In recent years, there is an increasing demand for heavy shipbuilding steel plate with excellent weldability in high heat input welding. During the thermal cycle, the microstructure of the heat affected zone (HAZ) of plates was damaged, and this markedly reduced toughness of HAZ. So, how to improve the toughness of HAZ has been a key subject in the fields of steel research. Oxide metallurgy is considered as an effective way to improve toughness of HAZ, because it could be used to retard grain growth by fine particles, which are stable at the high temperature.The high strength steel plate, which satisfies the low temperature specification, has been applied to offshore structure. Excellent properties of the plates and welded joints were obtained by oxide metallurgy technology, latest controlled rolling and accelerated cooling technology using Ultra-Fast Cooling (an on-line accelerated cooling system). The 355MPa-grade high strength steel plates with normalizing condition were obtained, and the steels have excellent weldability with heat input energy of 79 287kJ/cm, and the nil ductility transition (NDT) temperature was -70°C, which can satisfy the construction of offshore structure in cold regions.

Spatial distribution and historical trends of heavy metals in the sediments of petroleum producing regions of the Beibu Gulf, China.

PubMed

Yang, Jichao; Wang, Weiguo; Zhao, Mengwei; Chen, Bin; Dada, Olusegun A; Chu, Zhihui

2015-02-15

The concentrations of As, Sb, Hg, Pb, Cd, and Ba in the surface and core sediments of the oil and gas producing region of the Beibu Gulf were measured by Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES), Inductively Coupled Plasma Mass Spectrometry (ICP-MS) and Atomic Fluorescence Spectrometry (AFS), and the spatial distribution and historical trends of these elements are discussed. The results show that the concentrations of these elements are highest near the platforms. The results of Enrichment Factor (EF) and Potential Ecological Risk Index (PERI) also reveal significantly higher enrichment around the platforms, which imply that the offshore petroleum production was the cause of the unusual distribution and severe enrichment of these elements in the study area. The environment around the platforms was highly laden with toxic elements, thereby representing a very high ecological risk to the environment of the study area. Copyright © 2014 Elsevier Ltd. All rights reserved.

Drivers of coastal bacterioplankton community diversity and structure along a nutrient gradient in the East China Sea

NASA Astrophysics Data System (ADS)

He, Jiaying; Wang, Kai; Xiong, Jinbo; Guo, Annan; Zhang, Demin; Fei, Yuejun; Ye, Xiansen

2017-04-01

Anthropogenic nutrient discharge poses widespread threats to coastal ecosystems and has increased environmental gradients from coast to sea. Bacterioplankton play crucial roles in coastal biogeochemical cycling, and a variety of factors affect bacterial community diversity and structure. We used 16S rRNA gene pyrosequencing to investigate the spatial variation in bacterial community composition (BCC) across five sites on a coast-offshore gradient in the East China Sea. Overall, bacterial alpha-diversity did not differ across sites, except that richness and phylogenetic diversity were lower in the offshore sites, and the highest alpha-diversity was found in the most landward site, with Chl-a being the main factor. BCCs generally clustered into coastal and offshore groups. Chl-a explained 12.3% of the variation in BCCs, more than that explained by either the physicochemical (5.7%) or spatial (8.5%) variables. Nutrients (particularly nitrate and phosphate), along with phytoplankton abundance, were more important than other physicochemical factors, co-explaining 20.0% of the variation in BCCs. Additionally, a series of discriminant families (primarily affiliated with Gammaproteobacteria and Alphaproteobacteria), whose relative abundances correlated with Chl-a, DIN, and phosphate concentrations, were identified, implying their potential to indicate phytoplankton blooms and nutrient enrichment in this marine ecosystem. This study provides insight into bacterioplankton response patterns along a coast-offshore gradient, with phytoplankton abundance increasing in the offshore sites. Time-series sampling across multiple transects should be performed to determine the seasonal and spatial patterns in bacterial diversity and community structure along this gradient.

Drivers of coastal bacterioplankton community diversity and structure along a nutrient gradient in the East China Sea

NASA Astrophysics Data System (ADS)

He, Jiaying; Wang, Kai; Xiong, Jinbo; Guo, Annan; Zhang, Demin; Fei, Yuejun; Ye, Xiansen

2018-03-01

Anthropogenic nutrient discharge poses widespread threats to coastal ecosystems and has increased environmental gradients from coast to sea. Bacterioplankton play crucial roles in coastal biogeochemical cycling, and a variety of factors affect bacterial community diversity and structure. We used 16S rRNA gene pyrosequencing to investigate the spatial variation in bacterial community composition (BCC) across five sites on a coast-offshore gradient in the East China Sea. Overall, bacterial alpha-diversity did not differ across sites, except that richness and phylogenetic diversity were lower in the offshore sites, and the highest alpha-diversity was found in the most landward site, with Chl-a being the main factor. BCCs generally clustered into coastal and offshore groups. Chl-a explained 12.3% of the variation in BCCs, more than that explained by either the physicochemical (5.7%) or spatial (8.5%) variables. Nutrients (particularly nitrate and phosphate), along with phytoplankton abundance, were more important than other physicochemical factors, co-explaining 20.0% of the variation in BCCs. Additionally, a series of discriminant families (primarily affiliated with Gammaproteobacteria and Alphaproteobacteria), whose relative abundances correlated with Chl-a, DIN, and phosphate concentrations, were identified, implying their potential to indicate phytoplankton blooms and nutrient enrichment in this marine ecosystem. This study provides insight into bacterioplankton response patterns along a coast-offshore gradient, with phytoplankton abundance increasing in the offshore sites. Time-series sampling across multiple transects should be performed to determine the seasonal and spatial patterns in bacterial diversity and community structure along this gradient.

Resolving plate structure across the seismogenic zone in Cascadia from onshore-offshore receiver function imaging

NASA Astrophysics Data System (ADS)

Audet, P.; Schaeffer, A. J.

2017-12-01

Studies of the forearc structure in the Cascadia subduction zone using teleseismic P-wave receiver function have resolved structures associated with deep fluid cycling, such as the basalt-to-eclogite reaction and fluid overpressure within the subducting oceanic crust, as well as the serpentinization of the forearc mantle wedge. Unfortunately, the updip extent of the over-pressured zone, and therefore the possible control on the transition from episodic slow slip to seismic slip, occurs offshore and is not resolved in those studies. The Cascadia Initiative (CI) has provided an opportunity to extend this work to the locked zone using teleseismic receiver functions from the deployment of a dense line of ocean-bottom seismograph stations offshore of Washington State, from the trench to the coastline. Here we calculate P-wave receiver functions using data from offshore (CI) and onshore (CAFE) broadband seismic stations. These data clearly show the various scattered phases associated with a dipping low-velocity layer that was identified in previous studies as the downgoing oceanic crust. These signals are difficult to untangle offshore because they arrive at similar times. We process receiver functions using a modified common-conversion point (CCP) stacking technique that uses a coherency filter to optimally stack images obtained from the three main scattered phases. The resulting image shows along-dip variations in the character of the seismic discontinuities associated with the top and bottom of the low-velocity layer. Combined with focal depth information of regular and low-frequency earthquakes, these variations may reflect changes in the material properties of the megathrust across the seismogenic zone in Cascadia.

Amy Robertson | NREL

Science.gov Websites

validation, and data analysis. At NREL, Amy specializes in the modeling of offshore wind system dynamics. She Amy.Robertson@nrel.gov | 303-384-7157 Amy's expertise is in structural dynamics modeling, verification and of offshore wind modeling tools. Prior to joining NREL, Amy worked as an independent consultant for

Prediction of dynamic strains on a monopile offshore wind turbine using virtual sensors

NASA Astrophysics Data System (ADS)

Iliopoulos, A. N.; Weijtjens, W.; Van Hemelrijck, D.; Devriendt, C.

2015-07-01

The monitoring of the condition of the offshore wind turbine during its operational states offers the possibility of performing accurate assessments of the remaining life-time as well as supporting maintenance decisions during its entire life. The efficacy of structural monitoring in the case of the offshore wind turbine, though, is undermined by the practical limitations connected to the measurement system in terms of cost, weight and feasibility of sensor mounting (e.g. at muddline level 30m below the water level). This limitation is overcome by reconstructing the full-field response of the structure based on the limited number of measured accelerations and a calibrated Finite Element Model of the system. A modal decomposition and expansion approach is used for reconstructing the responses at all degrees of freedom of the finite element model. The paper will demonstrate the possibility to predict dynamic strains from acceleration measurements based on the aforementioned methodology. These virtual dynamic strains will then be evaluated and validated based on actual strain measurements obtained from a monitoring campaign on an offshore Vestas V90 3 MW wind turbine on a monopile foundation.

High-frequency guided ultrasonic waves to monitor corrosion thickness loss

NASA Astrophysics Data System (ADS)

Fromme, Paul; Bernhard, Fabian; Masserey, Bernard

2017-02-01

Corrosion due to adverse environmental conditions can occur for a range of industrial structures, e.g., ships and offshore oil platforms. Pitting corrosion and generalized corrosion can lead to the reduction of the strength and thus degradation of the structural integrity. The nondestructive detection and monitoring of corrosion damage in difficult to access areas can be achieved using high frequency guided ultrasonic waves propagating along the structure. Using standard ultrasonic transducers with single sided access to the structure, the two fundamental Lamb wave modes were selectively generated simultaneously, penetrating through the complete thickness of the structure. The wave propagation and interference of the guided wave modes depends on the thickness of the structure. Numerical simulations were performed using a 2D Finite Difference Method (FDM) algorithm in order to visualize the guided wave propagation and energy transfer across the plate thickness. Laboratory experiments were conducted and the wall thickness reduced initially uniformly by milling of the steel structure. Further measurements were conducted using accelerated corrosion in salt water. From the measured signal change due to the wave mode interference, the wall thickness reduction was monitored and good agreement with theoretical predictions was achieved. Corrosion can lead to non-uniform thickness reduction and the influence of this on the propagation of the high frequency guided ultrasonic waves was investigated. The wave propagation in a steel specimen with varying thickness was measured experimentally and the influence on the wave propagation characteristics quantified.

The Seismicity of Two Hyperextended Margins

NASA Astrophysics Data System (ADS)

Redfield, Tim; Terje Osmundsen, Per

2013-04-01

A seismic belt marks the outermost edge of Scandinavia's proximal margin, inboard of and roughly parallel to the Taper Break. A similar near- to onshore seismic belt runs along its inner edge, roughly parallel to and outboard of the asymmetric, seaward-facing escarpment. The belts converge at both the northern and southern ends of Scandinavia, where crustal taper is sharp and the proximal margin is narrow. Very few seismic events have been recorded on the intervening, gently-tapering Trøndelag Platform. Norway's distribution of seismicity is systematically ordered with respect to 1) the structural templates of high-beta extension that shaped the thinning gradient during Late Jurassic or Early Cretaceous time, and 2) the topographically resurgent Cretaceous-Cenozoic "accommodation phase" family of escarpments that approximate the innermost limit of crustal thinning [See Redfield and Osmundsen (2012) for diagrams, definitions, discussion, and supporting citations.] Landwards from the belt of earthquake epicenters that mark the Taper Break the crust consistently thickens, and large fault arrays tend to sole out at mid crustal levels. Towards the sea the crystalline continental crust is hyperextended, pervasively faulted, and generally very thin. Also, faulting and serpentinization may have affected the uppermost parts of the distal margin's lithospheric mantle. Such contrasting structural conditions may generate a contrasting stiffness: for a given stress, more strain can be accommodated in the distal margin than in the less faulted proximal margin. By way of comparison, inboard of the Taper Break on the gently-tapered Trøndelag Platform, faulting was not penetrative. There, similar structural conditions prevail and proximal margin seismicity is negligible. Because stress concentration can occur where material properties undergo significant contrast, the necking zone may constitute a natural localization point for post-thinning phase earthquakes. In Scandinavia, loads generated by escarpment erosion, offshore sedimentary deposition, and post-glacial rebound have been periodically superimposed throughout the Neogene. Their vertical stress patterns are mutually-reinforcing during deglaciation. However, compared to the post-glacial dome the pattern of maximum uplift/unloading generated by escarpment erosion will be longer, more linear, and located atop the emergent proximal margin. The pattern of offshore maximum deposition/loading will be similar. This may help explain the asymmetric expenditure of Fennoscandia's annual seismic energy budget. It may also help explain the obvious Conundrum: if stress generated by erosion and deposition is sufficiently great, fault reactivation and consequent seismicity can occur at any hyperextended passive margin sector regardless of its glacial history. Onshore Scandinavia, episodic footwall uplift and escarpment rejuvenation may have been driven by just such a mechanism throughout much of the later Cretaceous and Cenozoic. SE Brasil offers a glimpse of how Norway's hyperextended margin might manifest itself seismically in the absence of post-glacial rebound. Compilations suggest two seismic belts may exist. One, offshore, follows the thinned crust of the ultra-deep, hyperextended Campos and Santos basins. Onshore, earthquakes occur more commonly in the elevated highlands of the escarpments, and track especially the long, linear ranges such as the Serra de Mantiquiera and Serra do Espinhaço. Seismicity is more rare in the coastal lowlands, and largely absent in the Brasilian hinterland. Although never glaciated since the time of hyperextension and characterized by significantly fewer earthquakes in toto, SE Brasil's pattern of seismicity closely mimics Scandinavia. Commencing after perhaps just a few tens of millions of years of 'sag' basin infill, accommodation phase fault reactivation and footwall uplift at passive margins is the inexorable product of hyperextension. CITATIONS Redfield, T.F. and P.T. Osmundsen, 2012, GSA Bulletin, doi: 10.1130/B30691.1

Architecture and evolution of an Early Permian carbonate complex on a tectonically active island in east-central California

USGS Publications Warehouse

Stevens, Calvin H.; Magginetti, Robert T.; Stone, Paul

2015-01-01

The newly named Upland Valley Limestone represents a carbonate complex that developed on and adjacent to a tectonically active island in east-central California during a brief interval of Early Permian (late Artinskian) time. This lithologically unique, relatively thin limestone unit lies within a thick sequence of predominantly siliciclastic rocks and is characterized by its high concentration of crinoidal debris, pronounced lateral changes in thickness and lithofacies, and a largely endemic fusulinid fauna. Most outcrops represent a carbonate platform and debris derived from it and shed downslope, but another group of outcrops represents one or possibly more isolated carbonate buildups that developed offshore from the platform. Tectonic activity in the area occurred before, probably during, and after deposition of this short-lived carbonate complex.

Sleipner mishap jolts booming Norway

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-09-02

This paper reports on Norway's buoyant offshore industry that was stunned when the concrete substructure for Sleipner natural gas field's main production platform sank in the Grandsfjord off Stavanger late last month. The accident, a blow to Norway's gas sales program in Europe, came with offshore activity in the Norwegian North Sea moving into a new boom period. Currently, 10 oil and gas fields are under development, and several projects are on the drawing board. Aker Oil and Gas, a leading offshore firm, says the country's construction industry will be working at capacity for the next 4 years. Norwegian oilmore » production has been hovering just below 2 million b/d since the beginning of this year, making Norway the North Sea's largest producer, a position formerly held by the U.K. Gas production averages about 3 bcfd. With European gas demand sharply increasing, Norway is under pressure to increase output from new fields in the mid to late 1990s. The Sleipner setback forces state owned Den norske stats oljeselskap AS (Statoil) to cast around for supplies. Sleipner was to have begun deliveries to a consortium of continental gas companies in October 1993. Statoil believes it can fill the gap from existing fields in Norwegian waters.« less

U. K. pressing campaign to improve offshore safety

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knott, D.

1994-02-14

The U.K. government is making progress in its campaign to improve the safety of personnel working offshore. The government's Health and Safety Executive (HSE) plans to assess and pass judgment on at lease one safety plan, called a safety case, from each U.K. North Sea operator as soon as possible. HSE has agreed with the industry on a list of 61 priority safety cases, known as exemplars. Feedback from exemplar assessment will help operators review safety management and assist in preparation or revision of future safety cases. It also will give HSE practice in assessing a range of case types.more » The requirement for a safety program is part of new U.K. offshore legislation designed to prevent another accident similar to the Piper Alpha platform fire and explosion of 1988. After the transition period it will be against the law to operate an oil and gas installation in British waters without an accepted safety case. Besides existing installations, safety cases are also required for new installations reaching design stage by May 31, 1993, the date safety case regulations went into force. The paper describes the Cullen report, companies' experiences with the new law, and the safety assessment progress so far.« less

Epifauna dynamics at an offshore foundation--implications of future wind power farming in the North Sea.

PubMed

Krone, Roland; Gutow, Lars; Joschko, Tanja J; Schröder, Alexander

2013-04-01

In the light of the introduction of thousands of large offshore wind power foundations into the North Sea within the next decades, this manuscript focuses on the biofouling processes and likely reef effects. The study explores the macrozoobenthos (biofouling) colonization at an offshore platform which is comparable to offshore wind turbine foundations. A total of 183 single samples were taken and the parameters water depth and time were considered comparing biofouling masses and communities. The blue mussel Mytilus edulis, Anthozoa and the Amphipoda Jassa spp. were the dominant species. The community from the 1 m zone and those from the 5 and 20-28 m zones can clearly be differentiated. The 10 m zone community represents the transition between the M. edulis dominated 1 m and 5 m zones and the Anthozoa dominated 20-28 m zone. In the future offshore wind farms, thousands of wind turbine foundations will provide habitat for a hard bottom fauna which is otherwise restricted to the sparse rocky habitats scattered within extensive sedimentary soft bottoms of the German Bight. However, offshore wind power foundations cannot be considered natural rock equivalents as they selectively increase certain natural hard bottom species. The surface of the construction (1280 m²) was covered by an average of 4300 kg biomass. This foundation concentrates on its footprint area (1024 m²) 35 times more macrozoobenthos biomass than the same area of soft bottom in the German exclusive economic zone (0.12 kg m(-2)), functioning as a biomass hotspot. Concerning the temporal biomass variation, we assume that at least 2700 kg biomass was exported on a yearly basis. 345 × 10(4) single mussel shells of different sizes were produced during the study period. It is anticipated that the M. edulis abundance will increase in the North Sea due to the expansion of the offshore wind farm development. This will result in the enhanced production of secondary hard substrate (mussel shells) and its associated fauna and will intensify filtration rates of the seawater. This predicted ecological system change is coined the 'Mytilusation' of the German Bight. Copyright © 2012 Elsevier Ltd. All rights reserved.

International trends and issues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curtis, C

The nineteen (19) position statements in this paper represent Mr. Curtis` best efforts to capture Greenpeace`s views on ocean disposal or dumping of wastes and other harmful substances, including offshore oil and gas platforms. These statements, though, have not been formally approved as Greenpeace policies, although a number of them have appeared in Greenpeace documents or public statements. For this document, {open_quotes}dumping{close_quotes} refers to any deliberate disposal at sea of wastes or other matter, consistent with the London Convention.

Status in the development of self-powered wireless sensor node for structural health monitoring and prognosis

NASA Astrophysics Data System (ADS)

Godinez-Azcuaga, Valery F.; Farmer, Justin; Ziehl, Paul H.; Giurgiutiu, Victor; Nanni, Antonio; Inman, Daniel J.

2012-04-01

This paper discusses the development status of a self-powered wireless sensor node for steel and concrete bridges monitoring and prognosis. By the end of the third year in this four-year cross-disciplinary project, the 4-channel acoustic emission wireless node, developed by Mistras Group Inc, has already been deployed in concrete structures by the University of Miami. Also, extensive testing is underway with the node powered by structural vibration and wind energy harvesting modules developed by Virginia Tech. The development of diagnosis tools and models for bridge prognosis, which will be discussed in the paper, continues and the diagnosis tools are expected to be programmed in the node's AVR during the 4th year of the project. The impact of this development extends beyond the area of bridge health monitoring into several fields, such as offshore oil platforms, composite components on military ships and race boats, combat deployable bridges and wind turbine blades. Some of these applications will also be discussed. This project was awarded to a joint venture formed by Mistras Group Inc, Virginia Tech, University of South Carolina and University of Miami by the National Institute of Standards and Technology through its Technology Innovation Program Grant #70NANB9H007.

Tomographic Imaging of the Cascadia Subduction Zone and Juan de Fuca Plate System: Improved Methods Eliminate Artifacts and Reveal New Structures

NASA Astrophysics Data System (ADS)

Bodmer, M.; Toomey, D. R.; Hooft, E. E. E.; Bezada, M.; Schmandt, B.; Byrnes, J. S.

2017-12-01

Amphibious studies of subduction zones promise advances in understanding links between incoming plate structure, the subducting slab, and the upper mantle beneath the slab. However, joint onshore/offshore imaging is challenging due to contrasts between continental and oceanic structure. We present P-wave teleseismic tomography results for the Cascadia subduction zone (CSZ) that utilize existing western US datasets, amphibious seismic data from the Cascadia Initiative, and tomographic algorithms that permit 3D starting models, nonlinear ray tracing, and finite frequency kernels. Relative delay times show systematic onshore/offshore trends, which we attribute to structure in the upper 50 km. Shore-crossing CSZ seismic refraction models predict relative delays >1s, with equal contributions from elevation and crustal thickness. We use synthetic data to test methods of accounting for such shallow structure. Synthetic tests using only station static terms produce margin-wide, sub-slab low-velocity artifacts. Using a more realistic a priori 3D model for the upper 50 km better reproduces known input structures. To invert the observed delays, we use data-constrained starting models of the CSZ. Our preferred models utilize regional surface wave studies to construct a starting model, directly account for elevation, and use 3D nonlinear ray tracing. We image well-documented CSZ features, including the subducted slab down to 350 km, along strike slab variations below 150 km, and deep slab fragmentation. Inclusion of offshore data improves resolution of the sub-slab mantle, where we resolve localized low-velocity anomalies near the edges of the CSZ (beneath the Klamath and Olympic mountains). Our new imaging and resolution tests indicate that previously reported margin-wide, sub-slab low-velocity asthenospheric anomalies are an imaging artifact. Offshore, we observe low-velocity anomalies beneath the Gorda plate consistent with regional deformation and broad upwelling resulting from plate stagnation. At the Juan de Fuca Ridge we observe asymmetric low-velocity anomalies consistent with dynamic upwelling. Our results agree with recent offshore tomography studies using S wave data; however, differences in the recovered relative amplitudes are likely due to anisotropy, which we are exploring.

Guided waves in a monopile of an offshore wind turbine.

PubMed

Zernov, V; Fradkin, L; Mudge, P

2011-01-01

We study the guided waves in a structure which consists of two overlapping steel plates, with the overlapping section grouted. This geometry is often encountered in support structures of large industrial offshore constructions, such as wind turbine monopiles. It has been recognized for some time that the guided wave technology offers distinctive advantages for the ultrasonic inspections and health monitoring of structures of this extent. It is demonstrated that there exist advantageous operational regimes of ultrasonic transducers guaranteeing a good inspection range, even when the structures are totally submerged in water, which is a consideration when the wind turbines are deployed off shore. Copyright © 2010 Elsevier B.V. All rights reserved.

Implications of horsts and grabens on the development of canyons and seismicity on the west africa coast

NASA Astrophysics Data System (ADS)

Ola, Peter S.; Olabode, Solomon O.

2018-04-01

Subsurface basement topography in the Nigerian portion of the Benin Basin has been studied using borehole data of wells drilled to the basement and one strike line of seismic section. Two areas of a sharp drop in topography with a horst in between were observed in the study area. These features were projected to a seismic section in the offshore area of the Benin basin. The result depicts the structural features as horst and grabens coinciding with the Avon platform bounded on the right side by Ise graben, and the Orimedu graben to the left. The observed relationship of the grabens with the present day location of Avon Canyon on the seismic section also suggests an active subsidence along fractured zones. The subsidence, which probably is occurring along similar fracture zones in the Gulf of Guinea, could be responsible for the occasionally reported seismicity on the margin of West Africa. A detailed seismographic study of the fracture zones is recommended.

Effect of fast freeze-thaw cycles on mechanical properties of ordinary-air-entrained concrete.

PubMed

Shang, Huai-shuai; Cao, Wei-qun; Wang, Bin

2014-01-01

Freezing-thawing resistance is a very significant characteristic for concrete in severe environment (such as cold region with the lowest temperature below 0°C). In this study, ordinary-air-entrained (O-A-E) concrete was produced in a laboratory environment; the compressive strength, cubic compressive strength of C50, C40, C30, C25, and C20 ordinary-air-entrained concrete, tensile strength, and cleavage strength of C30 ordinary-air-entrained concrete were measured after fast freeze-thaw cycles. The effects of fast freeze-thaw cycles on the mechanical properties (compressive strength and cleavage strength) of ordinary-air-entrained concrete materials are investigated on the basis of the experimental results. And the concise mathematical formula between mechanical behavior and number of fast freeze-thaw cycles was established. The experiment results can be used as a reference in design, maintenance, and life prediction of ordinary-air-entrained concrete structure (such as dam, offshore platform, etc.) in cold regions.

Postmortem analysis of sand grain crushing from pile interface using X-ray tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silva, I. Matias; Combe, Gaeel; Foray, Pierre

2013-06-18

Pile foundations of offshore platforms, wind and water turbines are typically subjected to a variety of cyclic loading paths due to their complex environment. While many studies focus on global pile behaviour, the soil-pile interface is explored here by a micromechanical study of the soil layer in contact with the pile surface. This work is devoted to the analysis of frozen post-mortem silica sand samples recovered at the pile interface following installation and cyclic loading tests in a calibration chamber using x-ray tomography. An experimental procedure developed for three dimensional (3D) snow imaging was adapted for the recovery of themore » in-situ sand samples to preserve their structure during tomography scans. 3D images at a pixel size of 7 {mu}m were then obtained using a cryogenic cell. Results confirm the presence of a shear band at the pile surface as well as void ratios changes in the direction of the pile's radius.« less

Tower-Perturbation Measurements in Above-Water Radiometry

NASA Technical Reports Server (NTRS)

Hooker, Stanford B. (Editor); Firestone, Elaine R. (Editor); Zibordi, Giuseppe; Berthon, Jean-Francois; DAlimonte, Davide; vanderLinde, Dirk; Brown, James W.

2003-01-01

This report documents the scientific activities which took place during June 2001 and June 2002 on the Acqua Alta Oceanographic Tower (AAOT) in the northern Adriatic Sea. The primary objective of these field campaigns was to quantify the effect of platform perturbations (principally reflections of sunlight onto the sea surface) on above-water measurements of water-leaving radiances. The deployment goals documented in this report were to: a) collect an extensive and simultaneous set of above- and in-water optical measurements under predominantly clear-sky conditions; b) establish the vertical properties of the water column using a variety of ancillary measurements, many of which were taken coincidently with the optical measurements; and c) determine the bulk properties of the environment using a diversity of atmospheric, biogeochemical, and meteorological techniques. A preliminary assessment of the data collected during the two field campaigns shows the perturbation in above-water radiometry caused by a large offshore structure is very similar to that caused by a large research vessel.

Tower-Perturbation Measurements in Above-Water Radiometry. Volume 23

NASA Technical Reports Server (NTRS)

Hooker, Stanford B. (Editor); Firestone, Elaine R. (Editor); Zibordi, Giuseppe; Berthon, Jean-Francois; D'Alimonte, Davide; vanderLinde, Dirk; Brown, James W.

2003-01-01

This report documents the scientific activities which took place during June 2001 and June 2002 on the Acqua Alta Oceanographic Tower (AAOT) in the northern Adriatic Sea. The primary objective of these field campaigns was to quantify the effect of platform perturbations (principally reflections of sunlight onto the sea surface) on above-water measurements of water-leaving radiances. The deployment goals documented in this report were to: a) collect an extensive and simultaneous set of above- and in-water optical measurements under predominantly clear-sky conditions; b) establish the vertical properties of the water column using a variety of ancillary measurements, many of which were taken coincidently with the optical measurements; and c) determine the bulk properties of the environment using a diversity of atmospheric, biogeochemical, and meteorological techniques. A preliminary assessment of the data collected during the two field campaigns shows the perturbation in above-water radiometry caused by a large offshore structure is very similar to that caused by a large research vessel.

Effect of Fast Freeze-Thaw Cycles on Mechanical Properties of Ordinary-Air-Entrained Concrete

PubMed Central

Shang, Huai-shuai; Cao, Wei-qun; Wang, Bin

2014-01-01

Freezing-thawing resistance is a very significant characteristic for concrete in severe environment (such as cold region with the lowest temperature below 0°C). In this study, ordinary-air-entrained (O-A-E) concrete was produced in a laboratory environment; the compressive strength, cubic compressive strength of C50, C40, C30, C25, and C20 ordinary-air-entrained concrete, tensile strength, and cleavage strength of C30 ordinary-air-entrained concrete were measured after fast freeze-thaw cycles. The effects of fast freeze-thaw cycles on the mechanical properties (compressive strength and cleavage strength) of ordinary-air-entrained concrete materials are investigated on the basis of the experimental results. And the concise mathematical formula between mechanical behavior and number of fast freeze-thaw cycles was established. The experiment results can be used as a reference in design, maintenance, and life prediction of ordinary-air-entrained concrete structure (such as dam, offshore platform, etc.) in cold regions. PMID:24895671

Current and turbulence measurements at the FINO1 offshore wind energy site: analysis using 5-beam ADCPs

NASA Astrophysics Data System (ADS)

Bakhoday-Paskyabi, Mostafa; Fer, Ilker; Reuder, Joachim

2018-01-01

We report concurrent measurements of ocean currents and turbulence at two sites in the North Sea, one site at upwind of the FINO1 platform and the other 200-m downwind of the Alpha Ventus wind farm. At each site, mean currents, Reynolds stresses, turbulence intensity and production of turbulent kinetic energy are obtained from two bottom-mounted 5-beam Nortek Signature1000s, high-frequency Doppler current profiler, at a water depth of approximately 30 m. Measurements from the two sites are compared to statistically identify the effects of wind farm and waves on ocean current variability and the turbulent structure in the water column. Profiles of Reynolds stresses are found to be sensible to both environmental forcing and the wind farm wake-induced distortions in both boundary layers near the surface and the seabed. Production of turbulent kinetic energy and turbulence intensity exhibit approximately similar, but less pronounced, patterns in the presence of farm wake effects.

Final Technical Report. DeepCwind Consortium Research Program. January 15, 2010 - March 31, 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dagher, Habib; Viselli, Anthony; Goupee, Andrew

This is the final technical report for the U.S. Department of Energy-funded program, DE-0002981: DeepCwind Consortium Research Program. The project objective was the partial validation of coupled models and optimization of materials for offshore wind structures. The United States has a great opportunity to harness an indigenous abundant renewable energy resource: offshore wind. In 2010, the National Renewable Energy Laboratory (NREL) estimated there to be over 4,000 GW of potential offshore wind energy found within 50 nautical miles of the US coastlines (Musial and Ram, 2010). The US Energy Information Administration reported the total annual US electric energy generation inmore » 2010 was 4,120 billion kilowatt-hours (equivalent to 470 GW) (US EIA, 2011), slightly more than 10% of the potential offshore wind resource. In addition, deep water offshore wind is the dominant US ocean energy resource available comprising 75% of the total assessed ocean energy resource as compared to wave and tidal resources (Musial, 2008). Through these assessments it is clear offshore wind can be a major contributor to US energy supplies. The caveat to capturing offshore wind along many parts of the US coast is deep water. Nearly 60%, or 2,450 GW, of the estimated US offshore wind resource is located in water depths of 60 m or more (Musial and Ram, 2010). At water depths over 60 m building fixed offshore wind turbine foundations, such as those found in Europe, is likely economically infeasible (Musial et al., 2006). Therefore floating wind turbine technology is seen as the best option for extracting a majority of the US offshore wind energy resource. Volume 1 - Test Site; Volume 2 - Coupled Models; and Volume 3 - Composite Materials« less

Comparative analysis of a jack-up drilling unit with different leg systems

NASA Astrophysics Data System (ADS)

Ren, Xiangang; Bai, Yong; Jia, Lusheng

2012-09-01

The jack-up unit is one of the best drilling platforms in offshore oil fields with water depth shallower than 150 meters. As the most pivotal component of the jack-up unit, the leg system can directly affect the global performance of a jack-up unit. Investigation shows that there are three kinds of leg structure forms in the world now: the reverse K, X, and mixing types. In order to clarify the advantage and defects of each one, as well as their effect on the global performance of the jack-up unit, this paper commenced to study performance targets of a deepwater jack-up unit with different leg systems (X type, reverse K type, and mixing type). In this paper a typical leg scantling dimension and identical external loads were selected, detailed finite element snalysis (FEA) models were built to simulate the jack-up unit's structural behavior, and the multi-point constraint (MPC) element together with the spring element was used to deal with the boundary condition. Finally, the above problems were solved by comparative analysis of their main performance targets (including ultimate static strength, dynamic response, and weight).

Geologic implications and potential hazards of scour depressions on bering shelf, Alaska

USGS Publications Warehouse

Larsen, M.C.; Nelson, H.; Thor, D.R.

1979-01-01

Flat-bottomed depression 50-150 m in diameter and 60-80 cm deep occur in the floor of Norton Sound, Bering Sea. These large erosional bedforms and associated current ripples are found in areas where sediment grain size is 0.063-0.044 mm (4-4.5 ??), speeds of bottom currents are greatest (20-30 cm/s mean speeds under nonstorm conditions, 70 cm/s during typical storms), circulation of water is constricted by major topographic shoals (kilometers in scale), and small-scale topographic disruptions, such as ice gouges, occur locally on slopes of shoals. These local obstructions on shoals appear to disrupt currents, causing separation of flow and generating eddies that produce large-scale scour. Offshore artificial structures also may disrupt bottom currents in these same areas and have the potential to generate turbulence and induce extensive scour in the area of disrupted flow. The size and character of natural scour depressions in areas of ice gouging suggest that large-scale regions of scour may develop from enlargement of local scour sites around pilings, platforms, or pipelines. Consequently, loss of substrate support for pipelines and gravity structures is possible during frequent autumn storms. ?? 1979 Springer-Verlag New York Inc.

Feasibility study of tuned liquid column damper for ocean wave energy extraction

NASA Astrophysics Data System (ADS)

Wong, Yihong; King, Yeong-Jin; Lai, An-Chow; Chong, Kok-Keong; Lim, Boon-Han

2017-04-01

Intermittent nature and low efficiency are the major issues in renewable energy supply. To overcome these issues, one of the possible methods is through a hybrid system where multiple sources of renewable energy are combined to compensate each other's weaknesses. The hybrid of solar energy and wave energy becomes possible through the introduction of a stable floating platform which enables solar energy generation above it and wave energy harvesting underneath it. This paper is intended to study the feasibility of harnessing ocean wave energy using a tuned liquid column damper (TLCD), a type of passive damping device that is designed to suppress externally induced vibration force at a specific frequency range. The proposed TLCD is to be implemented within a floating offshore structure to serve as a vibration mitigating mechanism by reducing the dynamic response of the structure and simultaneously utilize the flowing motion of liquid within the TLCD for generating electricity. The constructed TLCD prototype is tuned according to theoretical study and tested using a shaking table with a predetermined frequency range. The oscillating motion of water within the TLCD and the potential of installation of hydro turbine generator in term of recoverable amount of energy are studied.

English-Spanish glossary: offshore exploration and production, gas processing, and valves (in Spanish)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-12-01

This series of articles contains 3 different English-Spanish glossaries of related terms used in the oil industry. The glossary of the offshore exploration and production involves a summary of terms used in the offshore oil activity. It also includes names of singular equipment used in offshore drilling, as well as several navigation terms in relation to the floating oil structures. With the help of the Gas Processors Association it was possible to compile a glossary of gas processing with a concise selection of common terms of the industry of gas processing. The glossary of valves includes more than 200 termsmore » of the industry of valves in a specialized glossary, and several explanations about the application and operation of valves.« less

Anti-icing property of bio-inspired micro-structure superhydrophobic surfaces and heat transfer model

NASA Astrophysics Data System (ADS)

Liu, Yan; Li, Xinlin; Jin, Jingfu; Liu, Jiaan; Yan, Yuying; Han, Zhiwu; Ren, Luquan

2017-04-01

Ice accumulation is a thorny problem which may inflict serious damage even disasters in many areas, such as aircraft, power line maintenance, offshore oil platform and locators of ships. Recent researches have shed light on some promising bio-inspired anti-icing strategies to solve this problem. Inspired by typical plant surfaces with super-hydrophobic character such as lotus leaves and rose petals, structured superhydrophobic surface are prepared to discuss the anti-icing property. 7075 Al alloy, an extensively used materials in aircrafts and marine vessels, is employed as the substrates. As-prepared surfaces are acquired by laser processing after being modified by stearic acid for 1 h at room temperature. The surface morphology, chemical composition and wettability are characterized by means of SEM, XPS, Fourier transform infrared (FTIR) spectroscopy and contact angle measurements. The morphologies of structured as-prepared samples include round hump, square protuberance and mountain-range-like structure, and that the as-prepared structured surfaces shows an excellent superhydrophobic property with a WCA as high as 166 ± 2°. Furthermore, the anti-icing property of as-prepared surfaces was tested by a self-established apparatus, and the crystallization process of a cooling water on the sample was recorded. More importantly, we introduced a model to analyze heat transfer process between the droplet and the structured surfaces. This study offers an insight into understanding the heat transfer process of the superhydrophobic surface, so as to further research about its unique property against ice accumulation.

Genetic divergence between two phenotypically distinct bottlenose dolphin ecotypes suggests separate evolutionary trajectories.

PubMed

Fruet, Pedro F; Secchi, Eduardo R; Di Tullio, Juliana C; Simões-Lopes, Paulo César; Daura-Jorge, Fábio; Costa, Ana P B; Vermeulen, Els; Flores, Paulo A C; Genoves, Rodrigo Cezar; Laporta, Paula; Beheregaray, Luciano B; Möller, Luciana M

2017-11-01

Due to their worldwide distribution and occupancy of different types of environments, bottlenose dolphins display considerable morphological variation. Despite limited understanding about the taxonomic identity of such forms and connectivity among them at global scale, coastal (or inshore) and offshore (or oceanic) ecotypes have been widely recognized in several ocean regions. In the Southwest Atlantic Ocean (SWA), however, there are scarce records of bottlenose dolphins differing in external morphology according to habitat preferences that resemble the coastal-offshore pattern observed elsewhere. The main aim of this study was to analyze the genetic variability, and test for population structure between coastal ( n  = 127) and offshore ( n  = 45) bottlenose dolphins sampled in the SWA to assess whether their external morphological distinction is consistent with genetic differentiation. We used a combination of mtDNA control region sequences and microsatellite genotypes to infer population structure and levels of genetic diversity. Our results from both molecular marker types were congruent and revealed strong levels of structuring (microsatellites F ST  = 0.385, p  < .001; mtDNA F ST  =  0.183, p  < .001; Φ ST  = 0.385, p  < .001) and much lower genetic diversity in the coastal than the offshore ecotype, supporting patterns found in previous studies elsewhere. Despite the opportunity for gene flow in potential "contact zones", we found minimal current and historical connectivity between ecotypes, suggesting they are following discrete evolutionary trajectories. Based on our molecular findings, which seem to be consistent with morphological differentiations recently described for bottlenose dolphins in our study area, we recommend recognizing the offshore bottlenose dolphin ecotype as an additional Evolutionarily Significant Unit (ESU) in the SWA. Implications of these results for the conservation of bottlenose dolphins in SWA are also discussed.

Atlantic continental margin of the United States

USGS Publications Warehouse

Grow, John A.; Sheridan, Robert E.; Palmer, A.R.

1982-01-01

The objective of this Decade of North American Geology (D-NAG) volume will be to focus on the Mesozoic and Cenozoic evolution of the U.S. Atlantic continental margin, including the onshore coastal plain, related onshore Triassic-Jurassic rift grabens, and the offshore basins and platforms. Following multiple compressional tectonic episodes between Africa and North America during the Paleozoic Era that formed the Appalachian Mountains, the Mesozoic and Cenozoic Eras were dominated by tensional tectonic processes that separated Africa and North America. Extensional rifting during Triassic and Early Jurassic times resulted in numerous tensional grabens both onshore and offshore, which filled with nonmarine continental red beds, lacustrine deposits, and volcanic flows and debris. The final stage of this breakup between Africa and North America occurred beneath the present outer continental shelf and continental slope during Early or Middle Jurassic time when sea-floor spreading began to form new oceanic crust and lithosophere between the two continents as they drifted apart. Postrift subsidence of the marginal basins continued in response to cooling of the lithosphere and sedimentary loading.Geophysical surveys and oil-exploration drilling along the U.S. Atlantic continental margin during the past 5 years are beginning to answer many questions concerning its deep structure and stratigraphy and how it evolved during the rifting and early sea-floor-spreading stages of the separation of this region from Africa. Earlier geophysical studies of the U.S. continental margin used marine refraction and submarine gravity measurements. Single-channel seismic-reflection, marine magnetic, aeromagnetic, and continuous gravity measurements became available during the 1960s.

Aerodynamic Simulation of the MARINTEK Braceless Semisubmersible Wave Tank Tests

NASA Astrophysics Data System (ADS)

Stewart, Gordon; Muskulus, Michael

2016-09-01

Model scale experiments of floating offshore wind turbines are important for both platform design for the industry as well as numerical model validation for the research community. An important consideration in the wave tank testing of offshore wind turbines are scaling effects, especially the tension between accurate scaling of both hydrodynamic and aerodynamic forces. The recent MARINTEK braceless semisubmersible wave tank experiment utilizes a novel aerodynamic force actuator to decouple the scaling of the aerodynamic forces. This actuator consists of an array of motors that pull on cables to provide aerodynamic forces that are calculated by a blade-element momentum code in real time as the experiment is conducted. This type of system has the advantage of supplying realistically scaled aerodynamic forces that include dynamic forces from platform motion, but does not provide the insights into the accuracy of the aerodynamic models that an actual model-scale rotor could provide. The modeling of this system presents an interesting challenge, as there are two ways to simulate the aerodynamics; either by using the turbulent wind fields as inputs to the aerodynamic model of the design code, or by surpassing the aerodynamic model and using the forces applied to the experimental turbine as direct inputs to the simulation. This paper investigates the best practices of modeling this type of novel aerodynamic actuator using a modified wind turbine simulation tool, and demonstrates that bypassing the dynamic aerodynamics solver of design codes can lead to erroneous results.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Bingbin; Karr, Dale G.; Song, Huimin

It is a fact that developing offshore wind energy has become more and more serious worldwide in recent years. Many of the promising offshore wind farm locations are in cold regions that may have ice cover during wintertime. The challenge of possible ice loads on offshore wind turbines raises the demand of modeling capacity of dynamic wind turbine response under the joint action of ice, wind, wave, and current. The simulation software FAST is an open source computer-aided engineering (CAE) package maintained by the National Renewable Energy Laboratory. In this paper, a new module of FAST for assessing the dynamicmore » response of offshore wind turbines subjected to ice forcing is presented. In the ice module, several models are presented which involve both prescribed forcing and coupled response. For conditions in which the ice forcing is essentially decoupled from the structural response, ice forces are established from existing models for brittle and ductile ice failure. For conditions in which the ice failure and the structural response are coupled, such as lock-in conditions, a rate-dependent ice model is described, which is developed in conjunction with a new modularization framework for FAST. In this paper, analytical ice mechanics models are presented that incorporate ice floe forcing, deformation, and failure. For lower speeds, forces slowly build until the ice strength is reached and ice fails resulting in a quasi-static condition. For intermediate speeds, the ice failure can be coupled with the structural response and resulting in coinciding periods of the ice failure and the structural response. A third regime occurs at high speeds of encounter in which brittle fracturing of the ice feature occurs in a random pattern, which results in a random vibration excitation of the structure. An example wind turbine response is simulated under ice loading of each of the presented models. This module adds to FAST the capabilities for analyzing the response of wind turbines subjected to forces resulting from ice impact on the turbine support structure. The conditions considered in this module are specifically addressed in the International Organization for Standardization (ISO) standard 19906:2010 for arctic offshore structures design consideration. Special consideration of lock-in vibrations is required due to the detrimental effects of such response with regard to fatigue and foundation/soil response. Finally, the use of FAST for transient, time domain simulation with the new ice module is well suited for such analyses.« less

Taking ownership of safety. What are the active ingredients of safety coaching and how do they impact safety outcomes in critical offshore working environments?

PubMed

Krauesslar, Victoria; Avery, Rachel E; Passmore, Jonathan

2015-01-01

Safety coaching interventions have become a common feature in the safety critical offshore working environments of the North Sea. Whilst the beneficial impact of coaching as an organizational tool has been evidenced, there remains a question specifically over the use of safety coaching and its impact on behavioural change and producing safe working practices. A series of 24 semi-structured interviews were conducted with three groups of experts in the offshore industry: safety coaches, offshore managers and HSE directors. Using a thematic analysis approach, several significant themes were identified across the three expert groups including connecting with and creating safety ownership in the individual, personal significance and humanisation, ingraining safety and assessing and measuring a safety coach's competence. Results suggest clear utility of safety coaching when applied by safety coaches with appropriate coach training and understanding of safety issues in an offshore environment. The current work has found that the use of safety coaching in the safety critical offshore oil and gas industry is a powerful tool in managing and promoting a culture of safety and care.

Scenario analysis for techno-economic model development of U.S. offshore wind support structures

DOE PAGES

Damiani, Rick; Ning, Andrew; Maples, Ben; ...

2016-09-22

Challenging bathymetry and soil conditions of future US offshore wind power plants might promote the use of multimember, fixed-bottom structures (or 'jackets') in place of monopiles. Support structures affect costs associated with the balance of system and operation and maintenance. Understanding the link between these costs and the main environmental design drivers is crucial in the quest for a lower levelized cost of energy, and it is the main rationale for this work. Actual cost and engineering data are still scarce; hence, we evaluated a simplified engineering approach to tie key site and turbine parameters (e.g. water depth, wave height,more » tower-head mass, hub height and generator rating) to the overall support weight. A jacket-and-tower sizing tool, part of the National Renewable Energy Laboratory's system engineering software suite, was utilized to achieve mass-optimized support structures for 81 different configurations. This tool set provides preliminary sizing of all jacket components. Results showed reasonable agreement with the available industry data, and that the jacket mass is mainly driven by water depth, but hub height and tower-head mass become more influential at greater turbine ratings. A larger sensitivity of the structural mass to wave height and target eigenfrequency was observed for the deepest water conditions (>40 m). Thus, techno-economic analyses using this model should be based on accurate estimates of actual metocean conditions and turbine parameters especially for deep waters. Finally, the relationships derived from this study will inform National Renewable Energy Laboratory's offshore balance of system cost model, and they will be used to evaluate the impact of changes in technology on offshore wind lower levelized cost of energy.« less

Self-represented witnessing: the use of social media by asylum seekers in Australia’s offshore immigration detention centres

PubMed Central

Rae, Maria; Holman, Rosa; Nethery, Amy

2017-01-01

The act of witnessing connects audiences with distant suffering. But what happens when bearing witness becomes severely restricted? External parties, including the mainstream news media, are constrained from accessing Australia’s offshore immigration detention centres. The effect is that people seeking asylum are hidden from the public and excluded from national debates. Some detainees have adopted social media as a platform to communicate their stories of flight, and their experiences of immigration detention, to a wider audience. This article examines the ways in which social media, and particularly Facebook, has facilitated what we call self-represented witnessing. We analyse two public Facebook pages to assess how detainees use such social media networks to document their experiences, and we observe the interaction between detainees, other social media users and mainstream media. Significantly, these social media networks enable detained asylum seekers to conduct an unmediated form of self-represented witnessing that exposes human rights abuses and documents justice claims. PMID:29782576

Digital depth horizon compilations of the Alaskan North Slope and adjacent Arctic regions

USGS Publications Warehouse

Saltus, Richard W.; Bird, Kenneth J.

2003-01-01

Data have been digitized and combined to create four detailed depth horizon grids spanning the Alaskan North Slope and adjacent offshore areas. These map horizon compilations were created to aid in petroleum system modeling and related studies. Topography/bathymetry is extracted from a recent Arctic compilation of global onshore DEM and satellite altimetry and ship soundings offshore. The Lower Cretaceous Unconformity (LCU), the top of the Triassic Shublik Formation, and the pre-Carboniferous acoustic basement horizon grids are created from numerous seismic studies, drill hole information, and interpolation. These horizons were selected because they mark critical times in the geologic evolution of the region as it relates to petroleum. The various horizons clearly show the major tectonic elements of this region including the Brooks Range, Colville Trough, Barrow Arch, Hanna Trough, Chukchi Platform, Nuwuk Basin, Kaktovik Basin, and Canada Basin. The gridded data are available in a variety of data formats for use in regional studies.

The effect of an oil drilling operation on the trace metal concentrations in offshore bottom sediments of the Campos Basin oil field, SE Brazil.

PubMed

Rezende, C E; Lacerda, L D; Ovalle, A R C; Souza, C M M; Gobo, A A R; Santos, D O

2002-07-01

The concentrations of Al, Fe, Mn, Zn, Cu, Pb, Ni, Cr, Ba, V, Sn and As in offshore bottom sediments from the Bacia de Campos oil field, SE Brazil, were measured at the beginning and at 7 months after completion of the drilling operation. Concentrations of Al, Fe, Ba, Cr, Ni and Zn were significantly higher closer to the drilling site compared to stations far from the site. Average concentrations of Al, Cu, and in particular of Ni, were significantly higher at the end of the drilling operation than at the beginning. Comparison between drilling area sediments with control sediments of the continental platform, however, showed no significant difference in trace metal concentrations. Under the operation conditions of this drilling event, the results show that while changes in some trace metal concentrations do occur during drilling operations, they are not significantly large to be distinguished from natural variability of the local background concentrations.

Offshore killer whale tracking using multiple hydrophone arrays.

PubMed

Gassmann, Martin; Henderson, E Elizabeth; Wiggins, Sean M; Roch, Marie A; Hildebrand, John A

2013-11-01

To study delphinid near surface movements and behavior, two L-shaped hydrophone arrays and one vertical hydrophone line array were deployed at shallow depths (<125 m) from the floating instrument platform R/P FLIP, moored northwest of San Clemente Island in the Southern California Bight. A three-dimensional propagation-model based passive acoustic tracking method was developed and used to track a group of five offshore killer whales (Orcinus orca) using their emitted clicks. In addition, killer whale pulsed calls and high-frequency modulated (HFM) signals were localized using other standard techniques. Based on these tracks sound source levels for the killer whales were estimated. The peak to peak source levels for echolocation clicks vary between 170-205 dB re 1 μPa @ 1 m, for HFM calls between 185-193 dB re 1 μPa @ 1 m, and for pulsed calls between 146-158 dB re 1 μPa @ 1 m.

Self-represented witnessing: the use of social media by asylum seekers in Australia's offshore immigration detention centres.

PubMed

Rae, Maria; Holman, Rosa; Nethery, Amy

2018-05-01

The act of witnessing connects audiences with distant suffering. But what happens when bearing witness becomes severely restricted? External parties, including the mainstream news media, are constrained from accessing Australia's offshore immigration detention centres. The effect is that people seeking asylum are hidden from the public and excluded from national debates. Some detainees have adopted social media as a platform to communicate their stories of flight, and their experiences of immigration detention, to a wider audience. This article examines the ways in which social media, and particularly Facebook, has facilitated what we call self-represented witnessing. We analyse two public Facebook pages to assess how detainees use such social media networks to document their experiences, and we observe the interaction between detainees, other social media users and mainstream media. Significantly, these social media networks enable detained asylum seekers to conduct an unmediated form of self-represented witnessing that exposes human rights abuses and documents justice claims.

Vega is first offshore development for Montedison

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1985-10-01

Montedison's Vega field, 15 miles off the southern tip of Sicily, has recoverable oil reserves of 400 million bbl. This is Montedison's first offshore development venture, although the operator has considerable onshore experience. It will be followed by a second field, the smaller Mila floating production system, also off Sicily. One platform will be placed on a template installed in 1983 with up to 18 pre-drilled wells in water depths of 480 ft. The field may hold up to 1 billion bbl of 16/sup 0/ crude, but geology is complex and heavily fractured. The template has 30 available drilling slots,more » and water injection is being considered. The Vega discovery well was drilled in 1980, with 5000 b/d tested from 1000-ft oil column in Strep-penosa shales. Subsequently five wells were drilled by the Glomar Biscay I semi. These wells were drilled to a depth of just over 8000 ft with a total deviation of 60/sup 0/. The template is the first in the Mediterranean.« less

Gulf of Mexico Helicopter Offshore System Technologies Engineering Needs Assessment

NASA Technical Reports Server (NTRS)

Koenke, Edmund J.; Carpenter, Elisabeth J.; Williams, Larry; Caiafa, Caesar

1999-01-01

The National Aeronautics and Space Administration (NASA), in partnership with the Federal Aviation Administration (FAA), is conducting a research and development program to modernize the National Airspace System (NAS). The mission of NASA's Advanced Air Transportation Technologies (AATT) project is to develop advanced Air Traffic Management (ATM) concepts and decision support tools for eventual deployment and implementation by the FAA and the private sector. One major objective of the NASA AATT project is to understand and promote the needs of all user classes. The Gulf of Mexico (GoMex) airspace has unique needs. A large number of helicopters operate in this area with only limited surveillance and sometimes-severe environmental conditions. Thunderstorms are the most frequent weather hazard during the spring, summer, and fall. In winter, reduced hours of daylight, low ceilings, strong winds, and icing conditions may restrict operations. Hurricanes impose the most severe weather hazard. The hurricane season, from June through October, normally requires at least one mass evacuation of all offshore platforms.

Undersea fiber optic technology for the offshore community

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mariano, J.J.

The explosive growth in demand for global communications has been met by a rapid evolution in the undersea fiber-optic technology, which in just a few years has become the predominant method of communication across the world`s oceans and seas. As the scope of applications has become broader, the technology has become more diverse, and now comprises a range of products capable of providing economical, reliable service in any subsea environment, from ocean depths to coastal lagoons. In this paper, the authors discuss how undersea lightwave technology is being applied to meet the communication and production control needs of the offshoremore » oil and gas industry. They discuss the trends and technology developments that are changing the economics of undersea fiber-optic communication networks, as well as synergies in the offshore industry. They consider various applications for the industry and means of enhancing the profitability of platform operations through reduced downtime, reduced operating cost, and enhanced safety. Finally, they discuss extensions to exploratory drilling and land-based operations.« less

Statistical analysis on the signals monitoring multiphase flow patterns in pipeline-riser system

NASA Astrophysics Data System (ADS)

Ye, Jing; Guo, Liejin

2013-07-01

The signals monitoring petroleum transmission pipeline in offshore oil industry usually contain abundant information about the multiphase flow on flow assurance which includes the avoidance of most undesirable flow pattern. Therefore, extracting reliable features form these signals to analyze is an alternative way to examine the potential risks to oil platform. This paper is focused on characterizing multiphase flow patterns in pipeline-riser system that is often appeared in offshore oil industry and finding an objective criterion to describe the transition of flow patterns. Statistical analysis on pressure signal at the riser top is proposed, instead of normal prediction method based on inlet and outlet flow conditions which could not be easily determined during most situations. Besides, machine learning method (least square supported vector machine) is also performed to classify automatically the different flow patterns. The experiment results from a small-scale loop show that the proposed method is effective for analyzing the multiphase flow pattern.

Anomalous Near-Surface Low-Salinity Pulses off the Central Oregon Coast

PubMed Central

Mazzini, Piero L. F.; Risien, Craig M.; Barth, John A.; Pierce, Stephen D.; Erofeev, Anatoli; Dever, Edward P.; Kosro, P. Michael; Levine, Murray D.; Shearman, R. Kipp; Vardaro, Michael F.

2015-01-01

From mid-May to August 2011, extreme runoff in the Columbia River ranged from 14,000 to over 17,000 m3/s, more than two standard deviations above the mean for this period. The extreme runoff was the direct result of both melting of anomalously high snowpack and rainfall associated with the 2010–2011 La Niña. The effects of this increased freshwater discharge were observed off Newport, Oregon, 180 km south of the Columbia River mouth. Salinity values as low as 22, nine standard deviations below the climatological value for this period, were registered at the mid-shelf. Using a network of ocean observing sensors and platforms, it was possible to capture the onshore advection of the Columbia River plume from the mid-shelf, 20 km offshore, to the coast and eventually into Yaquina Bay (Newport) during a sustained wind reversal event. Increased freshwater delivery can influence coastal ocean ecosystems and delivery of offshore, river-influenced water may influence estuarine biogeochemistry. PMID:26607750

DOE Office of Scientific and Technical Information (OSTI.GOV)

Corbett, R.A

Another quality crude oil is available from the North Sea. Norway's Oseberg crude oil entered the export market on Dec. 1, 1988. This premium, low-sulfur crude oil is currently being produced at approximately 240,000 b/d from the Norwegian sector of the North Sea. Two platforms, operated by Den Norske Stats Oijeselskap A.S. (Statoil), are currently in production, with a third scheduled to go into production in 1991. Oseberg is a typical, low-sulfur North Sea crude oil that will provide a full range of high-quality, low-sulfur products. The naphtha cuts are of intermediate to paraffinic quality, making them suitable for gasolinemore » production. The Oseberg crude is stabilized at the offshore platform and then transported to the Sture terminal, north of Bergen, Norway. The terminal can handle crude oil tankers up to 300,000 DWT.« less

Fine-scale spatial patterns in the demersal fish and invertebrate community in a northwest Atlantic ecosystem

NASA Astrophysics Data System (ADS)

Malek, Anna J.; Collie, Jeremy S.; Gartland, James

2014-06-01

The abundance, biomass, diversity, and species composition of the demersal fish and invertebrate community in Rhode Island Sound and Block Island Sound, an area identified for offshore renewable energy development, were evaluated for spatial and seasonal structure. We conducted 58 otter trawls and 51 beam trawls in the spring, summer and fall of 2009-2012, and incorporated additional data from 88 otter trawls conducted by the Northeast Area Monitoring and Assessment Program. We used regionally-grouped abundance, biomass, diversity, and size spectra to assess spatial patterns in the aggregate fish community, and hierarchical cluster analysis to evaluate trends in species assemblages. Our analyses revealed coherent gradients in fish community biomass, diversity and species composition extending from inshore to offshore waters, as well as patterns related to the differing bathymetry of Rhode Island and Block Island Sounds. The fish communities around Block Island and Cox's Ledge are particularly diverse, suggesting that the proximity of hard bottom habitat may be important in structuring fish communities in this area. Species assemblages in Rhode Island and Block Island Sounds are characterized by a combination of piscivores (silver hake, summer flounder, spiny dogfish), benthivores (American lobster, black sea bass, Leucoraja spp. skates, scup) and planktivores (sea scallop), and exhibit geographic patterns that are persistent from year to year, yet variable by season. Such distributions reflect the cross-shelf migration of fish and invertebrate species in the spring and fall, highlighting the importance of considering seasonal fish behavior when planning construction schedules for offshore development projects. The fine spatial scale (10 s of kms) of this research makes it especially valuable for local marine spatial planning efforts by identifying local-scale patterns in fish community structure that will enable future assessment of the ecological impacts of offshore development. As such, this knowledge of the spatial and temporal structure of the demersal fish community in Rhode Island and Block Island Sounds will help to guide the placement of offshore structures so as to preserve the ecological and economic value of the area.

Optimization of monopiles for offshore wind turbines.

PubMed

Kallehave, Dan; Byrne, Byron W; LeBlanc Thilsted, Christian; Mikkelsen, Kristian Kousgaard

2015-02-28

The offshore wind industry currently relies on subsidy schemes to be competitive with fossil-fuel-based energy sources. For the wind industry to survive, it is vital that costs are significantly reduced for future projects. This can be partly achieved by introducing new technologies and partly through optimization of existing technologies and design methods. One of the areas where costs can be reduced is in the support structure, where better designs, cheaper fabrication and quicker installation might all be possible. The prevailing support structure design is the monopile structure, where the simple design is well suited to mass-fabrication, and the installation approach, based on conventional impact driving, is relatively low-risk and robust for most soil conditions. The range of application of the monopile for future wind farms can be extended by using more accurate engineering design methods, specifically tailored to offshore wind industry design. This paper describes how state-of-the-art optimization approaches are applied to the design of current wind farms and monopile support structures and identifies the main drivers where more accurate engineering methods could impact on a next generation of highly optimized monopiles. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Offshore Windfarm Impact on Pelagic Primary Production in the Southern North Sea

NASA Astrophysics Data System (ADS)

Slavik, Kaela; Zhang, Wenyan; Lemmen, Carsten; Wirtz, Kai

2016-04-01

As society struggles to find solutions to mitigate global warming, the demand for renewable energy technology has increased. Especially investment in offshore wind energy has proliferated in the European Union, with projections over the next 15 years estimating an over 40 fold increase in total offshore wind electricity. Though built with the goal of reducing the environmental impacts associated with traditional energy production, the long-term ecological impacts of offshore windfarm structures is not yet well understood. The consequences are of particular importance in the southern North Sea, where the expansion of offshore windfarms is focused. Our study investigates how the gradual accumulation of epifaunal biomass on submerged substrate at offshore windfarms impacts ecosystem services in the southern North Sea. Biofouling is governed predominately by the filter feeder Mytilus edulis, which, as an ecological engineer, will further alter the surrounding benthic and pelagic environment. We reconstruct the distribution of benthic filter feeders in the SNS and generate scenarios of increased potential distribution based on available information of Mytilus edulis settlement at turbines and of turbine locations. These maps are coupled through the MOSSCO (Modular Coupling System for Shelves and Coasts) to state-of-the-art and high resolution hydrodynamic and ecosystem models. We find a substantial change in pelagic primary production as a result of additional Mytilus edulis growth at offshore windfarms.

The limits of seaward spreading and slope instability at the continental margin offshore Mt Etna, imaged by high-resolution 2D seismic data

NASA Astrophysics Data System (ADS)

Gross, Felix; Krastel, Sebastian; Geersen, Jacob; Behrmann, Jan Hinrich; Ridente, Domenico; Chiocci, Francesco Latino; Bialas, Jörg; Papenberg, Cord; Cukur, Deniz; Urlaub, Morelia; Micallef, Aaron

2016-01-01

Mount Etna is the largest active volcano in Europe. Instability of its eastern flank is well documented onshore, and continuously monitored by geodetic and InSAR measurements. Little is known, however, about the offshore extension of the eastern volcano flank, defining a serious shortcoming in stability models. In order to better constrain the active tectonics of the continental margin offshore the eastern flank of the volcano, we acquired a new high-resolution 2D reflection seismic dataset. The data provide new insights into the heterogeneous geology and tectonics at the continental margin offshore Mt Etna. The submarine realm is characterized by different blocks, which are controlled by local- and regional tectonics. A compressional regime is found at the toe of the continental margin, which is bound to a complex basin system. Both, the clear link between on- and offshore tectonic structures as well as the compressional regime at the easternmost flank edge, indicate a continental margin gravitational collapse as well as spreading to be present at Mt Etna. Moreover, we find evidence for the offshore southern boundary of the moving flank, which is identified as a right lateral oblique fault north of Catania Canyon. Our findings suggest a coupled volcano edifice/continental margin instability at Mt Etna, demonstrating first order linkage between on- and offshore tectonic processes.

Calibration and validation of a spar-type floating offshore wind turbine model using the FAST dynamic simulation tool

DOE PAGES

Browning, J. R.; Jonkman, J.; Robertson, A.; ...

2014-12-16

In this study, high-quality computer simulations are required when designing floating wind turbines because of the complex dynamic responses that are inherent with a high number of degrees of freedom and variable metocean conditions. In 2007, the FAST wind turbine simulation tool, developed and maintained by the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory (NREL), was expanded to include capabilities that are suitable for modeling floating offshore wind turbines. In an effort to validate FAST and other offshore wind energy modeling tools, DOE funded the DeepCwind project that tested three prototype floating wind turbines at 1/50 th scalemore » in a wave basin, including a semisubmersible, a tension-leg platform, and a spar buoy. This paper describes the use of the results of the spar wave basin tests to calibrate and validate the FAST offshore floating simulation tool, and presents some initial results of simulated dynamic responses of the spar to several combinations of wind and sea states. Wave basin tests with the spar attached to a scale model of the NREL 5-megawatt reference wind turbine were performed at the Maritime Research Institute Netherlands under the DeepCwind project. This project included free-decay tests, tests with steady or turbulent wind and still water (both periodic and irregular waves with no wind), and combined wind/wave tests. The resulting data from the 1/50th model was scaled using Froude scaling to full size and used to calibrate and validate a full-size simulated model in FAST. Results of the model calibration and validation include successes, subtleties, and limitations of both wave basin testing and FAST modeling capabilities.« less

Friction Stir Welding of Line-Pipe Steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanderson, Samuel; Mahoney, Murray; Feng, Zhili

Friction stir welding (FSW) offers both economic and technical advantages over conventional fusion welding practices for welding line-pipe. For offshore line-pipe construction, the economic savings has been shown to be considerable, approaching a calculated 25%. Offshore pipe is relatively small diameter but heavy wall compared to onshore pipe. One concern is the ability to achieve consistent full weld penetration in an on-site offshore FSW operation, e.g., on a lay-barge. In addition, depending on the size and morphology of the unwelded zone, lack of penetration at the weld root can be difficult if not impossible to detect by conventional NDE methods.more » Thus, an approach to assure consistent full penetration via process control is required for offshore line-pipe construction using FSW. For offshore construction, an internal structural mandrel can be used offering the opportunity to use a sacrificial anvil FSW approach. With this approach, a small volume of sacrificial material can be inserted into the structural anvil. The FSW tool penetrates into the sacrificial anvil, beyond the inner diameter of the pipe wall, thus assuring full penetration. The sacrificial material is subsequently removed from the pipe inner wall. In the work presented herein, FSW studies were completed on both 6 mm and 12 mm wall thickness line-pipe. Lastly, post-FSW evaluations including radiography, root-bend tests, and metallography demonstrated the merits of the sacrificial anvil approach to achieve consistent full penetration.« less

Geodynamics and synchronous filling of rift-type basin evolved through compression tectonics

NASA Astrophysics Data System (ADS)

Papdimitriou, Nikolas; Nader, Fadi; Gorini, Christian; Deschamps, Remy

2016-04-01

The Levant Basin falls in the category of frontier basins, and is bounded by the Eratosthenes seamount to the West, the Nile cone delta to the south, Cyprus to the north and Lebanon to the east. The Levant Basin was initially a rift type basin, which is located at a major plate boundary since the Late Triassic. It evolved later on through compression tectonics. The post-rift phase prevailed since the Late Jurassic and is expressed by the gradual initiation of a passive margin. A thick infill, mostly of deep water sediments (about 12 km thick) is accounted for the Levant Basin. The post-rift sediments are pinching-out along the slope of the well preserved (and imaged) eastern margin of the Eratosthenes seamount, which is essentially made up of Mesozoic platform carbonates (about 5 km). Thus, the Eratosthenes carbonate platform was adjacent to the deep marine facies of the Levant Basin until the late Cretaceous/Cenozoic. At that time, both the Eratosthenes seamount and the Levant Basin became part of a foreland basin along the Cyprus Arc zone as a result of the collision of the African and Eurasian plates. The objective of this contribution is to investigate the timing and the mechanisms of flexural subsidence as well as the sedimentary filling of Levant Basin (through a source-to-sink approach) in a well-deformed tectonic region. The interpretation of twenty-four 2D seismic profiles coupled with the available ODP wells, offshore Cyprus, aims to define the primary reflectors and seismic packages. Then, concepts of seismic stratigraphy and sequence stratigraphy are applied to achieve a better understanding of the tectonostratigraphy and sedimentary architecture of the Eratosthenes seamount (as an isolated carbonate platform) and its surroundings. Recent offshore discoveries south of the Eratosthenes seamount (e.g., Zhor) have confirmed the presence of gas accumulations exceeding 30Tcf in subsalt Lower Miocene carbonate buildups, making out the understanding of the evolution of this new frontier hydrocarbon province of great importance.

Can reef islands keep up with sea level? Exploring the interplay between sea-level rise, sediment supply, and overwash processes

NASA Astrophysics Data System (ADS)

Lorenzo-Trueba, J.

2016-02-01

Coral reef islands are accumulations of carbonate sediment deposited subaerially atop coral reef platforms. We hypothesize that the long-term evolution of reef islands is primarily controlled by the interplay between sea-level rise, sediment supply, and sediment overwash. Reef islands are supplied with sediment from offshore, in the form of reworked coral skeletons that originate at the reef edge and are carried onto the reef platform by waves, as well as in situ production on the reef flat itself. However, the primary mechanism that allows reef islands to keep pace with sea level is storm overwash, which enables the vertical transport of sediment from the periphery to the top of the island. Given the current lack of understanding on how production and overwash processes interact, we have constructed a morphodynamic model to elucidate and quantify how reef islands may respond to sea-level rise and changes in sediment production. Model results demonstrate that even if reef islands can remain subaerial over the coming century, this will require significant deposition of sediment atop the island and, in many cases, the island is expected to roll considerably over itself; both of these morphologic changes will negatively affect homes and infrastructure atop these islands. The model also suggests that as reef islands approach the lagoon edge of the reef platform, shoreline erosion and island drowning can be enhanced as sediment overwashes into the lagoon. Interestingly, this situation can only be avoided if either a high offshore sediment supply bulwarks the island in place or the system undergoes similar rates of overwash sedimentation from both the ocean and the lagoon sides. The model also allows us to explore the potential for increased overwash with increased storminess, increases in sediment supply due to bleaching or disturbance, or reduction of sediment supply as a result of reduced calcification rates due to ocean acidification.

Investigating the use of oil platform marine fouling invertebrates as monitors of oil exposure in the Northern Gulf of Mexico.

PubMed

Pie, Hannah V; Heyes, Andrew; Mitchelmore, Carys L

2015-03-01

The concentration of 51 parent and alkylated PAHs was examined in oysters, Ostrea equestris, and corals, Tubastrea coccinea, collected from oil-rig structures off the coast of Louisiana during April and May 2011 to investigate their potential use as monitors for offshore contamination events. Corals and oysters collected from both sampling trips had lower PAH accumulation than most bivalves collected in previous studies near the shoreline of Louisiana and elsewhere in the Gulf of Mexico. In April, total PAH (TPAH) concentrations ranged from 8.73 to 15.17 ng g(-1) in corals and 2.52 to 22.04 ng g(-1) in oysters. In May, corals and oysters had elevated concentrations of TPAH ranging from 24.28 to 79.23 ng g(-1) and 7.18 to 95.55 ng g(-1), respectively. This increase could be a result of Mississippi River flooding that occurred during that time, as evidenced by the high perylene concentrations (3.92-41.49 ng g(-1)) measured in May oysters. Oysters and corals collected in May from MC21B, the closest rig to the Mississippi River Delta, had the highest TPAH concentrations observed among all locations and the only rig to have predominantly petrogenic source inputs. Overall, given the low baseline of PAHs demonstrated in this study and the rapid accumulation of diagnostic chemicals in response to a possible contamination event (i.e. sediment plume from May flooding), oil-rig invertebrates could make excellent monitoring tools to examine the exposure to and recovery from oil (and oil-spill response options) in the offshore Northern Gulf of Mexico. Pre-spill baseline data of chemical and biological biomarkers of contamination is key to better estimating the impacts and recovery of oil exposure. Therefore, this screen of PAH accumulation represents a crucial first step in determining baseline contaminant levels in order to utilize these unique resources as monitors for offshore oil exposure in the Northern Gulf of Mexico. Copyright © 2014 Elsevier B.V. All rights reserved.

Observation of high-resolution wind fields and offshore wind turbine wakes using TerraSAR-X imagery

NASA Astrophysics Data System (ADS)

Gies, Tobias; Jacobsen, Sven; Lehner, Susanne; Pleskachevsky, Andrey

2014-05-01

1. Introduction Numerous large-scale offshore wind farms have been built in European waters and play an important role in providing renewable energy. Therefore, knowledge of behavior of wakes, induced by large wind turbines and their impact on wind power output is important. The spatial variation of offshore wind turbine wake is very complex, depending on wind speed, wind direction, ambient atmospheric turbulence and atmospheric stability. In this study we demonstrate the application of X-band TerraSAR-X (TS-X) data with high spatial resolution for studies on wind turbine wakes in the near and far field of the offshore wind farm Alpha Ventus, located in the North Sea. Two cases which different weather conditions and different wake pattern as observed in the TS-X image are presented. 2. Methods The space-borne synthetic aperture radar (SAR) is a unique sensor that provides two-dimensional information on the ocean surface. Due to their high resolution, daylight and weather independency and global coverage, SARs are particularly suitable for many ocean and coastal applications. SAR images reveal wind variations on small scales and thus represent a valuable means in detailed wind-field analysis. The general principle of imaging turbine wakes is that the reduced wind speed downstream of offshore wind farms modulates the sea surface roughness, which in turn changes the Normalized Radar Cross Section (NRCS, denoted by σ0) in the SAR image and makes the wake visible. In this study we present two cases at the offshore wind farm Alpha Ventus to investigate turbine-induced wakes and the retrieved sea surface wind field. Using the wind streaks, visible in the TS-X image and the shadow behind the offshore wind farm, induced by turbine wake, the sea surface wind direction is derived and subsequently the sea surface wind speed is calculated using the latest generation of wind field algorithm XMOD2. 3. Case study alpha ventus Alpha Ventus is located approximately 45 km from the coast of Borkum, Germany, and consists of twelve 5-Megawatt wind power turbines. The retrieved results are validated by comparing with QuikSCAT measurements, the results of the German Weather Service (DWD) atmospheric model and in-situ measurements of wind speed and wind direction, obtained from the research platform FiNO1, installed 400 m west of Alpha Ventus. 4. Conclusion In the presented case study we quantify the wake characteristics of wake length, wake width, maximum velocity de?cit, wake merging and wake meandering. We show that SAR has the capability to map the sea surface two-dimensionally in high spatial resolution which provides a unique opportunity to observe spatial characteristics of offshore wind turbine wakes. The SAR derived information can support offshore wind farming with respect to optimal siting and design and help to estimate their effects on the environment.

Intelligent Fasteners

NASA Technical Reports Server (NTRS)

1997-01-01

Under a Small Business Innovation Research contract from Marshall Space Flight Center, Ultrafast, Inc. developed the world's first, high-temperature resistant, "intelligent" fastener. NASA needed a critical-fastening appraisal and validation of spacecraft segments that are coupled together in space. The intelligent-bolt technology deletes the self-defeating procedure of having to untighten the fastener, and thus upset the joint, during inspection and maintenance. The Ultrafast solution yielded an innovation that is likely to revolutionize manufacturing assembly, particularly the automobile industry. Other areas of application range from aircraft, computers and fork-lifts to offshore platforms, buildings, and bridges.

Military Use of Offshore Platforms

DTIC Science & Technology

1979-04-09

a 31 foot cabin area. The S-61N is signifi-- cantly longer than the Navy’s SH-3. The S-61N can also carry external loads of more than 7,000 pounds. At...using two external fuel tanks . In order to accomplish an ocean surveillance or radar flood/hold down mission with the helicopter’s LN-66 radar, radar...slashed from the FY-78 DOD budget. The vans which have dUi’eady been completed together with some that are partially completed, are presently in storage at

Magnetic mapping for structural geology and geothermal exploration in Guadeloupe, Lesser Antilles

NASA Astrophysics Data System (ADS)

Mercier de Lépinay, jeanne; munschy, marc; geraud, yves; diraison, marc; navelot, vivien; verati, christelle; corsini, michel; lardeaux, jean marc; favier, alexiane

2017-04-01

This work is implemented through the GEOTREF program which benefits from the support of both the ADEME and the French public funds "Investments for the future". The program focuses on the exploration for geothermal resources in Guadeloupe, Lesser Antilles, where a geothermal power plant is in production since 1986 (Bouillante, Basse Terre). In Les Saintes archipelago, in the south of Guadeloupe, the outcrop analysis of Terre-de-Haut Island allows to point out an exhumed geothermal paleo-system that is thought to be an analogue of the Bouillante active geothermal system. We show that a detailed marine magnetic survey with a quantitative interpretation can bring information about the offshore structures around Les Saintes archipelago in order to extend the geological limits and structural elements. A similar survey and workflow is also conducted offshore Basse-Terre where more geophysical data is already available. In order to correctly link the offshore and onshore structures, the magnetic survey must be close enough to the shoreline and sufficiently detailed to correctly outline the tectonic structures. An appropriate solution for such a survey is to use a three component magnetometer aboard a speedboat. Such a boat allows more navigation flexibility than a classic oceanic vessel towing a magnetometer; it can sail at higher speed on calm seas and closer to the shoreline. This kind of magnetic acquisition is only viable because the magnetic effect of the ship can be compensated using the same algorithms than those used for airborne magnetometry. The use of potential field transforms allows a large variety of structures to be highlighted, providing insights to build a general understanding of the nature and distribution of the magnetic sources. In particular, we use the tilt angle operator to better identify the magnetic lineaments offshore in order to compare them to the faults identified onshore during the outcrop analysis. All the major faults and fractures directions observed onshore are well represented through the magnetic lineaments except the main N90-110 system which is almost inexistent. We also invert the magnetic data to obtain a magnetization intensity map. This inversion assumes a constant depth magnetized layer and a constant magnetization's direction. The calculated variations on the map are consistent with on-field measurements showing that hydrothermalized rocks have a lower magnetic susceptibility (2 orders of magnitude) than fresh ones. Our interpretation and the onshore structural and petrographic analysis allow us to recognize the offshore extension of the hydrothermalized area, as well as different structural orientations.

Coastal Ohio Wind Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorsevski, Peter; Afjeh, Abdollah; Jamali, Mohsin

The Coastal Ohio Wind Project intends to address problems that impede deployment of wind turbines in the coastal and offshore regions of Northern Ohio. The project evaluates different wind turbine designs and the potential impact of offshore turbines on migratory and resident birds by developing multidisciplinary research, which involves wildlife biology, electrical and mechanical engineering, and geospatial science. Firstly, the project conducts cost and performance studies of two- and three-blade wind turbines using a turbine design suited for the Great Lakes. The numerical studies comprised an analysis and evaluation of the annual energy production of two- and three-blade wind turbinesmore » to determine the levelized cost of energy. This task also involved wind tunnel studies of model wind turbines to quantify the wake flow field of upwind and downwind wind turbine-tower arrangements. The experimental work included a study of a scaled model of an offshore wind turbine platform in a water tunnel. The levelized cost of energy work consisted of the development and application of a cost model to predict the cost of energy produced by a wind turbine system placed offshore. The analysis found that a floating two-blade wind turbine presents the most cost effective alternative for the Great Lakes. The load effects studies showed that the two-blade wind turbine model experiences less torque under all IEC Standard design load cases considered. Other load effects did not show this trend and depending on the design load cases, the two-bladed wind turbine showed higher or lower load effects. The experimental studies of the wake were conducted using smoke flow visualization and hot wire anemometry. Flow visualization studies showed that in the downwind turbine configuration the wake flow was insensitive to the presence of the blade and was very similar to that of the tower alone. On the other hand, in the upwind turbine configuration, increasing the rotor blade angle of attack reduced the wake size and enhanced the vortices in the flow downstream of the turbine-tower compared with the tower alone case. Mean and rms velocity distributions from hot wire anemometer data confirmed that in a downwind configuration, the wake of the tower dominates the flow, thus the flow fields of a tower alone and tower-turbine combinations are nearly the same. For the upwind configuration, the mean velocity shows a narrowing of the wake compared with the tower alone case. The downwind configuration wake persisted longer than that of an upwind configuration; however, it was not possible to quantify this difference because of the size limitation of the wind tunnel downstream of the test section. The water tunnel studies demonstrated that the scale model studies could be used to adequately produce accurate motions to model the motions of a wind turbine platform subject to large waves. It was found that the important factors that affect the platform is whether the platform is submerged or surface piercing. In the former, the loads on the platform will be relatively reduced whereas in the latter case, the structure pierces the wave free surface and gains stiffness and stability. The other important element that affects the movement of the platform is depth of the sea in which the wind turbine will be installed. Furthermore, the wildlife biology component evaluated migratory patterns by different monitoring systems consisting of marine radar, thermal IR camera and acoustic recorders. The types of radar used in the project are weather surveillance radar and marine radar. The weather surveillance radar (1988 Doppler), also known as Next Generation Radar (NEXRAD), provides a network of weather stations in the US. Data generated from this network were used to understand general migratory patterns, migratory stopover habitats, and other patterns caused by the effects of weather conditions. At a local scale our marine radar was used to complement the datasets from NEXRAD and to collect additional monitoring parameters such as passage rates, flight paths, flight directions, and flight altitudes of nocturnal migrating species. Our work focused on the design and development of custom built marine radar that used t-bar and parabolic dish antennas. The marine radar used in the project was Furuno (XANK250) which was coupled with a XIR3000B digitizing card from Russell Technologies for collection of the radar data. The radar data was processed by open source radR processing software using different computational techniques and methods. Additional data from thermal IR imaging cameras were collected to detect heat emitted from objects and provide information on movements of birds and bats, data which we used for different animal flight behavior analysis. Lastly, the data from the acoustic recorders were used to provide the number of bird calls for assessing patterns and peak passage rates during migration. The development of the geospatial database included collection of different data sources that are used to support offshore wind turbine development. Many different data sets were collected and organized using initial version of web-based repository software tools that can accommodate distribution of rectified pertinent data sets such as the lake depth, lake bottom engineering parameters, extent of ice, navigation pathways, wind speed, important bird habitats, fish efforts and other layers that are relevant for supporting robust offshore wind turbine developments. Additional geospatial products developed during the project included few different prototypes for offshore wind farm suitability which can involve different stakeholders and participants for solving complex planning problems and building consensus. Some of the prototypes include spatial decision support system (SDSS) for collaborative decision making, a web-based Participatory Geographic Information System (PGIS) framework for evaluating importance of different decision alternatives using different evaluation criteria, and an Android application for collection of field data using mobile and tablet devices . In summary, the simulations of two- and three-blade wind turbines suggested that two-bladed machines could produce comparable annual energy as the three-blade wind turbines but have a lighter tower top weight, which leads to lower cost of energy. In addition, the two-blade rotor configuration potentially costs 20% less than a three blade configuration that produces the same power at the same site. The cost model analysis predicted a potential cost savings of approximately 15% for offshore two-blade wind turbines. The foundation design for a wind turbine in Lake Erie is likely to be driven by ice loads based on the currently available ice data and ice mechanics models. Hence, for Lake Eire, the cost savings will be somewhat smaller than the other lakes in the Great Lakes. Considering the size of cranes and vessels currently available in the Great Lakes, the cost optimal wind turbine size should be 3 MW, not larger. The surveillance data from different monitoring systems suggested that bird and bat passage rates per hour were comparable during heavy migrations in both spring and fall seasons while passage rates were significantly correlated to wind directions and wind speeds. The altitude of migration was higher during heavy migrations and higher over water relative to over land. Notable portions of migration on some spring nights occurred parallel the shoreline, often moving perpendicular to southern winds. The birds approaching the Western basin have a higher propensity to cross than birds approaching the Central basin of Lake Erie and as such offshore turbine development might be a better option further east towards Cleveland than in the Western basin. The high stopover density was more strongly associated with migration volume the following night rather than the preceding night. The processed mean scalar wind speeds with temporal resolutions as fine as 10-minute intervals near turbine height showed that August is the month with the weakest winds while December is the month, which typically has the strongest winds. The ice data suggests that shallow western basin of Lake Erie has higher ice cover duration many times exceeding 90 days during some winters.« less

Work, eat and sleep: towards a healthy ageing at work program offshore.

PubMed

Riethmeister, Vanessa; Brouwer, Sandra; van der Klink, Jac; Bültmann, Ute

2016-02-09

Health management tools need to be developed to foster healthy ageing at work and sustain employability of ageing work-forces. The objectives of this study were to 1) perform a needs assessment to identify the needs of offshore workers in the Dutch Continental Shelf with regard to healthy ageing at work and 2) to define suitable program objectives for a future healthy ageing at work program in the offshore working population. A mixed methods design was used applying an intervention mapping procedure. Qualitative data were gathered in N = 19 semi-structured interviews and six focus-group sessions (N = 49). Qualitative data were used to develop a questionnaire, which was administered among N = 450 offshore workers. Subgroup analyses were performed to investigate age-related differences relating to health status and work-related factors. The importance of good working environments, food, as well as sleep/fatigue management was identified by the qualitative data analysis. A total of 260 offshore workers completed the questionnaire. Significant differences in work ability were found between offshore workers aged <45 and 45-54 years (mean 8.63 vs. 8.19; p = 0.005) and offshore workers aged <45 and >55 years (mean 8.63 vs. 8.22; p = 0.028). Offshore workers had a high BMI (M = 27.06, SD = 3.67), with 46 % classified as overweight (BMI 25-30) and 21 % classified as obese (BMI >30). A significant difference in BMI was found between offshore workers aged <45 and ≥55 years (mean 26.3 vs. 28.6; p <0.001). In total, 73 % of offshore workers reported prolonged fatigue. A significant difference in fatigue scores was found between offshore workers aged <45 and ≥55 years (mean 36.0 vs. 37.6; p = 0.024). Further, a "dip" was reported by 41 % of offshore workers. Dips were mainly experienced at day 10 or 11 (60 %), with 45 % experiencing the dip both as physical and mental fatigue, whereas 39 % experienced the dip as only mental fatigue. Both qualitative and quantitative analyses identified work, food and sleep/fatigue management as most important program objectives for a healthy ageing at work and sustainable employability program offshore. Future studies should investigate possible causes of dip occurrences and high fatigue scores to identify suitable interventions.

Yucatan Subsurface Stratigraphy from Geophysical Data, Well Logs and Core Analyses in the Chicxulub Impact Crater and Implications for Target Heterogeneities

NASA Astrophysics Data System (ADS)

Canales, I.; Fucugauchi, J. U.; Perez-Cruz, L. L.; Camargo, A. Z.; Perez-Cruz, G.

2011-12-01

Asymmetries in the geophysical signature of Chicxulub crater are being evaluated to investigate on effects of impact angle and trajectory and pre-existing target structural controls for final crater form. Early studies interpreted asymmetries in the gravity anomaly in the offshore sector to propose oblique either northwest- and northeast-directed trajectories. An oblique impact was correlated to the global ejecta distribution and enhanced environmental disturbance. In contrast, recent studies using marine seismic data and computer modeling have shown that crater asymmetries correlate with pre-existing undulations of the Cretaceous continental shelf, suggesting a structural control of target heterogeneities. Documentation of Yucatan subsurface stratigraphy has been limited by lack of outcrops of pre-Paleogene rocks. The extensive cover of platform carbonate rocks has not been affected by faulting or deformation and with no rivers cutting the carbonates, information comes mainly from the drilling programs and geophysical surveys. Here we revisit the subsurface stratigraphy in the crater area from the well log data and cores retrieved in the drilling projects and marine seismic reflection profiles. Other source of information being exploited comes from the impact breccias, which contain a sampling of disrupted target sequences, including crystalline basement and Mesozoic sediments. We analyze gravity and seismic data from the various exploration surveys, including multiple Pemex profiles in the platform and the Chicxulub experiments. Analyses of well log data and seismic profiles identify contacts for Lower Cretaceous, Cretaceous/Jurassic and K/Pg boundaries. Results show that the Cretaceous continental shelf was shallower on the south and southwest than on the east, with emerged areas in Quintana Roo and Belize. Mesozoic and upper Paleozoic sediments show variable thickness, possibly reflecting the crystalline basement regional structure. Paleozoic and Precambrian basement outcrops are located farther to the southeast in Belize and northern Guatemala. Inferred shelf paleo-bathymetry supports existence of a sedimentary basin extending to the northeast, where crater rim and terrace zones are subdued in the seismic images.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cornaggia, F.; Congo, S.A.; Agostino, M.

Kitina field is located in Marine VII permit, offshore Congo. The field was discovered in 1991 by a joint venture composed of Agip Recherches Congo (operator), Hydrocongo and Chevron International Limited. The field is a structural four-way dip closure trap shaped as turtle-back. Halokinetic movements are responsible for the structuring. The seismic imaging of the reservoir is affected by strong lateral velocity variations caused by different sedimentation across the paleo-shelf edge in the post-Albian sequence. One pass 3D poststack depth migration, performed with a velocity field obtained by means of geostatistical integration of 2D seismic and wellbore velocities, achieved amore » good compromise between high dip reflector imaging and depths at well location. Three main reservoirs of lower Albian age exist between -2100 and -3100m. They are separated by tight mudstones which act as intraformational seal. Seismic trace inversion improved the resolution of petrophysical variations in some of the field reservoirs, which have the following characteristics (from top to bottom): reservoir 2A is composed of bioclastic and oolitic packstone-grainstone laid down during regional regressive phase in insulated offshore bars on the crest of structural high. Early diagenetic phenomena lead to the development of world class permeability framework. Reservoir 1A-1B are composed of sandstone bodies which were deposited as shoreface to offshore bars during short-term regressive pulse. The 1A-1B reservoir, are embedded in mudstones deposited during long lasting phases of relative high stand in relatively deep offshore setting characterised by high, halokinetic driven subsidence.« less

Lower plate deformation structures along the Costa Rica erosive plate boundary - results from IODP Expedition 344 (CRISP 2)

NASA Astrophysics Data System (ADS)

Brandstätter, Jennifer; Kurz, Walter; Micheuz, Peter; Krenn, Kurt

2015-04-01

The primary objective of Integrated Ocean Drilling Program (IODP) Expedition 344 offshore the Osa Peninsula in Costa Rica was to sample and quantify the material entering the seismogenic zone of the Costa Rican erosive subduction margin. Fundamental to this objective is an understanding of the nature of both the subducting Cocos plate crust and of the overriding Caribbean plate. The subducting Cocos plate is investigated trying to define its hydrologic system and thermal state. The forearc structures recorded by the sediment deposited on the forearc, instead, document periods of uplift and subsidence and provide important information about the process of tectonic erosion that characterizes the Costa Rica margin. Offshore the western margin of Costa Rica, the oceanic Cocos plate subducts under the Caribbean plate, forming the southern end of the Middle America Trench. Subduction parameters including the age, convergence rate, azimuth, obliquity, morphology, and slab dip all vary along strike. The age of the Cocos plate at the Middle America Trench decreases from 24 Ma offshore the Nicoya Peninsula to 15 Ma offshore the Osa Peninsula. Subduction rates vary from 70 mm/y offshore Guatemala to 90 mm/y offshore southern Costa Rica. Convergence obliquity across the trench varies from offshore Nicaragua, where it is as much as 25° oblique, to nearly orthogonal southeast of the Nicoya Peninsula. Passage of the Cocos plate over the Galapagos hotspot created the aseismic Cocos Ridge, an overthickened welt of oceanic crust. This ridge is ~25 km thick, greater than three times normal oceanic crustal thickness. During IODP Expedition 344, the incoming Cocos plate was drilled at sites U1381 and U1414. Site U1381 is located ~4.5 km seaward of the deformation front offshore the Osa Peninsula and Caño Island. It is located on a local basement high. Basement relief often focuses fluid flow, so data from this site are likely to document the vigor of fluid flow in this area. Site U1414 is located ~1 km seaward of the deformation front offshore the Osa Peninsula and Caño Island. Primary science goals at Site U1414 included characterization of the alteration state of the magmatic basement. Brittle structures within the incoming plate (sites U1380, U1414) are mineralized extensional fractures and shear fractures. The shear fractures mainly show a normal component of shear. Within the sedimentary sequence both types of fractures dip steeply (vertical to subvertical) and strike NNE-SSW. Deformation bands trend roughly ENE-WSW, sub-parallel to the trend of the Cocos ridge. Structures in the Cocos Ridge basalt mainly comprise mineralized veins at various orientations. A preferred orientation of strike directions was not observed. Some veins show straight boundaries, others are characterized by an irregular geometry characterized by brecciated wall rock clasts embedded within vein precipitates. The vein mineralization was analysed in detail by RAMAN spectroscopy. Precipitation conditions and fluid chemistry were analysed by fluid inclusions entrapped within vein minerals. Vein mineralizations mainly consist of carbonate (fibrous aragonite, calcite), chalcedony, and quartz. Vein mineralization is mainly characterized by zoned antitaxial growth of carbonate fibres including a suture along the central vein domains. Quartz is often characterized by fibre growth of crystals perpendicular to the vein boundaries, too. These zoned veins additinally have wall rock alteration seams consisting of clay minerals. The precipitation sequence basically indicates that fluid chemistry evolved from an CO2-rich towards a SiO2- rich fluid.

Geomorphological and sedimentary processes of the glacially influenced northwestern Iberian continental margin and abyssal plains

NASA Astrophysics Data System (ADS)

Llave, Estefanía; Jané, Gloria; Maestro, Adolfo; López-Martínez, Jerónimo; Hernández-Molina, F. Javier; Mink, Sandra

2018-07-01

The offshore region of northwestern Iberia offers an opportunity to study the impacts of along-slope processes on the morphology of a glacially influenced continental margin, which has traditionally been conceptually characterised by predominant down-slope sedimentary processes. High-resolution multibeam bathymetry, acoustic backscatter and ultrahigh-resolution seismic reflection profile data are integrated and analysed to describe the present-day and recent geomorphological features and to interpret their associated sedimentary processes. Seventeen large-scale seafloor morphologies and sixteen individual echo types, interpreted as structural features (escarpments, marginal platforms and related fluid escape structures) and depositional and erosional bedforms developed either by the influence of bottom currents (moats, abraded surfaces, sediment waves, contourite drifts and ridges) or by gravitational features (gullies, canyons, slides, channel-levee complexes and submarine fans), are identified for the first time in the study area (spanning 90,000 km2 and water depths of 300 m to 5 km). Different types of slope failures and turbidity currents are mainly observed on the upper and lower slopes and along submarine canyons and deep-sea channels. The middle slope morphologies are mostly determined by the actions of bottom currents (North Atlantic Central Water, Mediterranean Outflow Water, Labrador Sea Water and North Atlantic Deep Water), which thereby define the margin morphologies and favour the reworking and deposition of sediments. The abyssal plains (Biscay and Iberian) are characterised by pelagic deposits and channel-lobe systems (the Cantabrian and Charcot), although several contourite features are also observed at the foot of the slope due to the influence of the deepest water masses (i.e., the North Atlantic Deep Water and Lower Deep Water). This work shows that the study area is the result of Mesozoic to present-day tectonics (e.g. the marginal platforms and structural highs). Therefore, tectonism constitutes a long-term controlling factor, whereas the climate, sediment supply and bottom currents play key roles in the recent short-term architecture and dynamics. Moreover, the recent predominant along-slope sedimentary processes observed in the studied northwestern Iberian Margin represent snapshots of the progressive stages and mixed deep-water system developments of the marginal platforms on passive margins and may provide information for a predictive model of the evolution of other similar margins.

Discussion of the paper 'Hydrates offshore Brazil'

USGS Publications Warehouse

Dillon, William P.

1994-01-01

The paper “Hydrates Offshore Brazil” by Rogerio L. Fontana and Alexandre Mussumeci presents some important information that strongly indicates the presence of gas hydrates on the southern Brazilian continental margin. However, the acoustic compressional wave velocity structure reported for the Brazilian margin sediments is highly unusual and quite puzzling. We will discuss a possible explanation related to the presence of gas hydrate and free gas in the sediments.

A surface ice module for wind turbine dynamic response simulation using FAST

DOE PAGES

Yu, Bingbin; Karr, Dale G.; Song, Huimin; ...

2016-06-03

It is a fact that developing offshore wind energy has become more and more serious worldwide in recent years. Many of the promising offshore wind farm locations are in cold regions that may have ice cover during wintertime. The challenge of possible ice loads on offshore wind turbines raises the demand of modeling capacity of dynamic wind turbine response under the joint action of ice, wind, wave, and current. The simulation software FAST is an open source computer-aided engineering (CAE) package maintained by the National Renewable Energy Laboratory. In this paper, a new module of FAST for assessing the dynamicmore » response of offshore wind turbines subjected to ice forcing is presented. In the ice module, several models are presented which involve both prescribed forcing and coupled response. For conditions in which the ice forcing is essentially decoupled from the structural response, ice forces are established from existing models for brittle and ductile ice failure. For conditions in which the ice failure and the structural response are coupled, such as lock-in conditions, a rate-dependent ice model is described, which is developed in conjunction with a new modularization framework for FAST. In this paper, analytical ice mechanics models are presented that incorporate ice floe forcing, deformation, and failure. For lower speeds, forces slowly build until the ice strength is reached and ice fails resulting in a quasi-static condition. For intermediate speeds, the ice failure can be coupled with the structural response and resulting in coinciding periods of the ice failure and the structural response. A third regime occurs at high speeds of encounter in which brittle fracturing of the ice feature occurs in a random pattern, which results in a random vibration excitation of the structure. An example wind turbine response is simulated under ice loading of each of the presented models. This module adds to FAST the capabilities for analyzing the response of wind turbines subjected to forces resulting from ice impact on the turbine support structure. The conditions considered in this module are specifically addressed in the International Organization for Standardization (ISO) standard 19906:2010 for arctic offshore structures design consideration. Special consideration of lock-in vibrations is required due to the detrimental effects of such response with regard to fatigue and foundation/soil response. Finally, the use of FAST for transient, time domain simulation with the new ice module is well suited for such analyses.« less

Fatigue reassessment for lifetime extension of offshore wind monopile substructures

NASA Astrophysics Data System (ADS)

Ziegler, Lisa; Muskulus, Michael

2016-09-01

Fatigue reassessment is required to decide about lifetime extension of aging offshore wind farms. This paper presents a methodology to identify important parameters to monitor during the operational phase of offshore wind turbines. An elementary effects method is applied to analyze the global sensitivity of residual fatigue lifetimes to environmental, structural and operational parameters. Therefore, renewed lifetime simulations are performed for a case study which consists of a 5 MW turbine with monopile substructure in 20 m water depth. Results show that corrosion, turbine availability, and turbulence intensity are the most influential parameters. This can vary strongly for other settings (water depth, turbine size, etc.) making case-specific assessments necessary.

Indus basin off Pakistan contains few wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quadri, V.N.; Quadri, S.M.G.J.

1997-06-16

The U.N. Conference on the Law of the Sea reaffirmed sovereignty of nations over 22 km of territorial sea, a 370 km Exclusive Economic Zone (EEZ), and rights over the continental shelf to at least 370 km and out to 648 km or beyond under specified conditions. With a coast line of about 990 km, the EEZ for Pakistan extends over an area almost 240,000 sq km, or 40% of the land sedimentary area, in which two distinct geological provinces, and the Indus Offshore and the Makran offshore, have been defined. The paper discusses the tectonics, structure, exploration history, andmore » play types offshore Pakistan. Data show a potential for both oil and gas.« less

Structural Considerations of a 20MW Multi-Rotor Wind Energy System

NASA Astrophysics Data System (ADS)

Jamieson, P.; Branney, M.

2014-12-01

The drive to upscale offshore wind turbines relates especially to possiblereductions in O&M and electrical interconnection costs per MW of installed capacity.Even with best current technologies, designs with rated capacity above about 3 MW are less cost effective exfactory per rated MW(turbine system costs) than smaller machines.Very large offshore wind turbines are thereforejustifiedprimarily by overall offshore project economics. Furthermore, continuing progress in materials and structures has been essential to avoid severe penalties in the power/mass ratio of large multi-MW machines.The multi-rotor concept employs many small rotors to maximise energy capture area withminimum systemvolume. Previous work has indicated that this can enablea very large reduction in the total weight and cost of rotors and drive trains compared to an equivalent large single rotor system.Thus the multi rotor concept may enable rated capacities of 20 MW or more at a single maintenancesite. Establishing the cost benefit of a multi rotor system requires examination of solutions for the support structure and yawing, ensuring aerodynamic losses from rotor interaction are not significant and that overall logistics, with much increased part count (more reliable components) and less consequence of single failuresare favourable. This paper addresses the viability of a support structure in respect of structural concept and likely weight as one necessary step in exploring the potential of the multi rotor concept.

Structural health and prognostics management for the enhancement of offshore wind turbine operations and maintenance strategies

DOE PAGES

Griffith, D. Todd; Yoder, Nathanael C.; Resor, Brian; ...

2013-09-19

Offshore wind turbines are an attractive source for clean and renewable energy for reasons including their proximity to population centers and higher capacity factors. One obstacle to the more widespread installation of offshore wind turbines in the USA, however, is that recent projections of offshore operations and maintenance costs vary from two to five times the land-based costs. One way in which these costs could be reduced is through use of a structural health and prognostics management (SHPM) system as part of a condition-based maintenance paradigm with smart loads management. Our paper contributes to the development of such strategies bymore » developing an initial roadmap for SHPM, with application to the blades. One of the key elements of the approach is a multiscale simulation approach developed to identify how the underlying physics of the system are affected by the presence of damage and how these changes manifest themselves in the operational response of a full turbine. A case study of a trailing edge disbond is analysed to demonstrate the multiscale sensitivity of damage approach and to show the potential life extension and increased energy capture that can be achieved using simple changes in the overall turbine control and loads management strategy. Finally, the integration of health monitoring information, economic considerations such as repair costs versus state of health, and a smart loads management methodology provides an initial roadmap for reducing operations and maintenance costs for offshore wind farms while increasing turbine availability and overall profit.« less

Integrity management of offshore structures and its implication on computation of structural action effects and resistance

NASA Astrophysics Data System (ADS)

Moan, T.

2017-12-01

An overview of integrity management of offshore structures, with emphasis on the oil and gas energy sector, is given. Based on relevant accident experiences and means to control the associated risks, accidents are categorized from a technical-physical as well as human and organizational point of view. Structural risk relates to extreme actions as well as structural degradation. Risk mitigation measures, including adequate design criteria, inspection, repair and maintenance as well as quality assurance and control of engineering processes, are briefly outlined. The current status of risk and reliability methodology to aid decisions in the integrity management is briefly reviewed. Finally, the need to balance the uncertainties in data, methods and computational efforts and the cautious use and quality assurance and control in applying high fidelity methods to avoid human errors, is emphasized, and with a plea to develop both high fidelity as well as efficient, simplified methods for design.

New Insights Into Valley Formation and Preservation: Geophysical Imaging of the Offshore Trinity River Paleovalley

NASA Astrophysics Data System (ADS)

Speed, C. M.; Swartz, J. M.; Gulick, S. P. S.; Goff, J.

2017-12-01

The Trinity River paleovalley is an offshore stratigraphic structure located on the inner continental shelf of the Gulf of Mexico offshore Galveston, Texas. Its formation is linked to the paleo-Trinity system as it existed across the continental shelf during the last glacial period. Newly acquired high-resolution geophysical data have imaged more complexity to the valley morphology and shelf stratigraphy than was previously captured. Significantly, the paleo-Trinity River valley appears to change in the degree of confinement and relief relative to the surrounding strata. Proximal to the modern shoreline, the interpreted time-transgressive erosive surface formed by the paleo-river system is broad and rugose with no single valley, but just 5 km farther offshore the system appears to become confined to a 10 km wide valley structure before again becoming unconfined once again 30 km offshore. Fluvial stratigraphy in this region has a similar degree of complexity in morphology and preservation. A dense geophysical survey of several hundred km is planned for Fall 2017, which will provide unprecedented imaging of the paleovalley morphology and associated stratigraphy. Our analysis leverages robust chirp processing techniques that allow for imaging of strata on the decimeter scale. We will integrate our geophysical results with a wide array of both newly collected and previously published sediment cores. This approach will allow us to address several key questions regarding incised valley formation and preservation on glacial-interglacial timescales including: to what extent do paleo-rivers remain confined within a single broad valley structure, what is the fluvial systems response to transgression, and what stratigraphy is created and preserved at the transition from fluvial to estuarine environments? Our work illustrates that traditional models of incised valley formation and subsequent infilling potentially fail to capture the full breadth of dynamics of past river systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The original concept envisioned for the use of Fischer-Tropsch processing (FTP) of United States associated natural gas in this study was to provide a way of utilizing gas which could not be brought to market because a pipeline was not available or for which there was no local use. Conversion of gas by FTP could provide a means of utilizing offshore associated gas which would not require installation of a pipeline or re-injection. The premium quality F-T hydrocarbons produced by conversion of the gas can be transported in the same way as the crude oil or in combination (blended) withmore » it, eliminating the need for a separate gas transport system. FTP will produce a synthetic crude oil, thus increasing the effective size of the resource. The two conventional approaches currently used in US territory for handling of natural gas associated with crude petroleum production are re-injection and pipelining. Conversion of natural gas to a liquid product which can be transported to shore by tanker can be accomplished by FTP to produce hydrocarbons, or by conversion to chemical products such as methanol or ammonia, or by cryogenic liquefaction (LNG). This study considers FTP and briefly compares it to methanol and LNG. The Energy International Corporation cobalt catalyst, ratio adjusted, slurry bubble column F-T process was used as the basis for the study and the comparisons. An offshore F-T plant can best be accommodated by an FPSO (Floating Production, Storage, Offloading vessel) based on a converted surplus tanker, such as have been frequently used around the world recently. Other structure types used in deep water (platforms) are more expensive and cannot handle the required load.« less

Reassessment of the Seismicity and seismic hazards of Libya

NASA Astrophysics Data System (ADS)

Ben Suleman, A.; Elmeladi, A.

2009-04-01

The tectonic evolution of Libya, located at the northern extreme of the African continent, has yielded a complex crustal structure that is composed of a series of basins and uplifts. The present day deformation of Libya is the result of the Eurasia-Africa continental collision. At the end of the year 2005, The Libyan National Seismological Network was established to monitor local, regional and teleseismic activities, as well as to provide high quality data for research projects both locally and on the regional and global scale. This study aims to discuss the seismicity of Libya by using the new data from the Libyan national seismological network and to focus on the seismic hazards. At first glance the seismic activity map shows dominant trends of seismicity with most of the seismic activity concentrated along the northern coastal areas. Four major seismic trends were quite noticeable. A first trend is a NW-SE direction coinciding with the eastern boarder of the Hun Graben. A second trend is also a NW-SE direction in the offshore area and might be a continuation of this trend. The other two trends were located in the western Gulf of Sirt and Cyrenaica platform. The rest of seismicity is diffuse either offshore or in land, with no good correlation with well-mapped faults. Detailed investigations of the Libyan seismicity indicates that the Libya has experienced earthquakes of varying magnitudes and that there is definitely a certain amount of seismic risk involved in engineering projects, particularly in the northern regions. Detailed investigation of the distribution of the Libyan earthquakes in space and time along with all other geological considerations suggested the classification of the country into four seismic zones with the Hun graben zone being the most seismically active zone.

Potential Impact of Submarine Power Cables on Crab Harvest

NASA Astrophysics Data System (ADS)

Bull, A. S.; Nishimoto, M.

2016-02-01

Offshore renewable energy installations convert wave or wind energy to electricity and transfer the power to shore through transmission cables laid on or buried beneath the seafloor. West coast commercial fishermen, who harvest the highly prized Dungeness crab (Metacarcinus magister) and the rock crab (Cancer spp.), are concerned that the interface of crabs and electromagnetic fields (EMF) from these cables will present an electrified fence on the seafloor that their target resource will not cross. Combined with the assistance of professional fishermen, submarine transmission cables that electrify island communities and offshore oil platforms in the eastern Pacific provide an opportunity to test the harvest of crab species across power transmission cables. In situ field techniques give commercial crab species a choice to decide if they will cross fully energized, EMF emitting, power transmission cables, in response to baited traps. Each independent trial is either one of two possible responses: the crab crosses the cable to enter a trap (1) or the crab does not cross the cable to enter a trap (0). Conditions vary among sample units by the following categorical, fixed factors (i.e., covariates) of cable structure (buried or unburied); direction of cable from crab position (west or east, north or south); time and season. A generalized linear model is fit to the data to determine whether any of these factors affect the probability of crabs crossing an energized cable to enter baited traps. Additionally, the experimental design, aside from the number of runs (set of sample trials) and the dates of the runs, is the same in the Santa Barbara Channel for rock crab and Puget Sound for Dungeness crab, and allows us to compare the capture rates of the two species in the two areas. We present preliminary results from field testing in 2015.

33 CFR 148.400 - What does this subpart do?

Code of Federal Regulations, 2012 CFR

2012-07-01

... topographic and geologic structure of the ocean bottom to determine its ability to support offshore structures and other equipment; and (3) Studies done for the preparation of the environmental analysis required...

Critical Factors Analysis for Offshore Software Development Success by Structural Equation Modeling

NASA Astrophysics Data System (ADS)

Wada, Yoshihisa; Tsuji, Hiroshi

In order to analyze the success/failure factors in offshore software development service by the structural equation modeling, this paper proposes to follow two approaches together; domain knowledge based heuristic analysis and factor analysis based rational analysis. The former works for generating and verifying of hypothesis to find factors and causalities. The latter works for verifying factors introduced by theory to build the model without heuristics. Following the proposed combined approaches for the responses from skilled project managers of the questionnaire, this paper found that the vendor property has high causality for the success compared to software property and project property.

Aspects of structural health and condition monitoring of offshore wind turbines

PubMed Central

Antoniadou, I.; Dervilis, N.; Papatheou, E.; Maguire, A. E.; Worden, K.

2015-01-01

Wind power has expanded significantly over the past years, although reliability of wind turbine systems, especially of offshore wind turbines, has been many times unsatisfactory in the past. Wind turbine failures are equivalent to crucial financial losses. Therefore, creating and applying strategies that improve the reliability of their components is important for a successful implementation of such systems. Structural health monitoring (SHM) addresses these problems through the monitoring of parameters indicative of the state of the structure examined. Condition monitoring (CM), on the other hand, can be seen as a specialized area of the SHM community that aims at damage detection of, particularly, rotating machinery. The paper is divided into two parts: in the first part, advanced signal processing and machine learning methods are discussed for SHM and CM on wind turbine gearbox and blade damage detection examples. In the second part, an initial exploration of supervisor control and data acquisition systems data of an offshore wind farm is presented, and data-driven approaches are proposed for detecting abnormal behaviour of wind turbines. It is shown that the advanced signal processing methods discussed are effective and that it is important to adopt these SHM strategies in the wind energy sector. PMID:25583864

Aspects of structural health and condition monitoring of offshore wind turbines.

PubMed

Antoniadou, I; Dervilis, N; Papatheou, E; Maguire, A E; Worden, K

2015-02-28

Wind power has expanded significantly over the past years, although reliability of wind turbine systems, especially of offshore wind turbines, has been many times unsatisfactory in the past. Wind turbine failures are equivalent to crucial financial losses. Therefore, creating and applying strategies that improve the reliability of their components is important for a successful implementation of such systems. Structural health monitoring (SHM) addresses these problems through the monitoring of parameters indicative of the state of the structure examined. Condition monitoring (CM), on the other hand, can be seen as a specialized area of the SHM community that aims at damage detection of, particularly, rotating machinery. The paper is divided into two parts: in the first part, advanced signal processing and machine learning methods are discussed for SHM and CM on wind turbine gearbox and blade damage detection examples. In the second part, an initial exploration of supervisor control and data acquisition systems data of an offshore wind farm is presented, and data-driven approaches are proposed for detecting abnormal behaviour of wind turbines. It is shown that the advanced signal processing methods discussed are effective and that it is important to adopt these SHM strategies in the wind energy sector.

Recent advances in the development of a self-powered wireless sensor network for structural health prognosis

NASA Astrophysics Data System (ADS)

Godinez-Azcuaga, Valery F.; Inman, Daniel J.; Ziehl, Paul H.; Giurgiutiu, Victor; Nanni, Antonio

2011-04-01

This paper presents the most recent advances in the development of a self powered wireless sensor network for steel and concrete bridges monitoring and prognosis. This five-year cross-disciplinary project includes development and deployment of a 4-channel acoustic emission wireless node powered by structural vibration and wind energy harvesting modules. In order to accomplish this ambitious goal, the project includes a series of tasks that encompassed a variety of developments such as ultra low power AE systems, energy harvester hardware and especial sensors for passive and active acoustic wave detection. Key studies on acoustic emission produced by corrosion on reinforced concrete and by crack propagation on steel components to develop diagnosis tools and models for bridge prognosis are also a part of the project activities. It is important to mention that the impact of this project extends beyond the area of bridge health monitoring. Several wireless prototype nodes have been already requested for applications on offshore oil platforms, composite ships, combat deployable bridges and wind turbines. This project was awarded to a joint venture formed by Mistras Group Inc, Virginia Tech, University of South Carolina and University of Miami and is sponsored through the NIST-TIP Grant #70NANB9H007.

Earth Observations in Support of Offshore Wind Energy Management in the Euro-Atlantic Region

NASA Astrophysics Data System (ADS)

Liberato, M. L. R.

2017-12-01

Climate change is one of the most important challenges in the 21st century and the energy sector is a major contributor to GHG emissions. Therefore greater attention has been given to the evaluation of offshore wind energy potentials along coastal areas, as it is expected offshore wind energy to be more efficient and cost-effective in the near future. Europe is developing offshore sites for over two decades and has been growing at gigawatt levels in annual capacity. Portugal is among these countries, with the development of a 25MW WindFloat Atlantic wind farm project. The international scientific community has developed robust ability on the research of the climate system components and their interactions. Climate scientists have gained expertise in the observation and analysis of the climate system as well as on the improvement of model and predictive capabilities. Developments on climate science allow advancing our understanding and prediction of the variability and change of Earth's climate on all space and time scales, while improving skilful climate assessments and tools for dealing with future challenges of a warming planet. However the availability of greater datasets amplifies the complexity on manipulation, representation and consequent analysis and interpretation of such datasets. Today the challenge is to translate scientific understanding of the climate system into climate information for society and decision makers. Here we discuss the development of an integration tool for multidisciplinary research, which allows access, management, tailored pre-processing and visualization of datasets, crucial to foster research as a service to society. One application is the assessment and monitoring of renewable energy variability, such as wind or solar energy, at several time and space scales. We demonstrate the ability of the e-science platform for planning, monitoring and management of renewable energy, particularly offshore wind energy in the Euro-Atlantic region. Further we explore the automatization of processes using different domains and datasets, which facilitate further research in evaluating and understanding renewable energy variability. AcknowledgementsThis work is supported by Foundation for Science and Technology (FCT), Portugal, project UID/GEO/50019/2013 - Instituto Dom Luiz.

Continental Shelf Morphology and Stratigraphy Offshore San Onofre, CA: The Interplay Between Rates of Eustatic Change and Sediment Supply

USGS Publications Warehouse

Klotsko, Shannon; Driscoll, Neal W.; Kent, Graham; Brothers, Daniel

2016-01-01

New high-resolution CHIRP seismic data acquired offshore San Onofre, southern California reveal that shelf sediment distribution and thickness are primarily controlled by eustatic sea level rise and sediment supply. Throughout the majority of the study region, a prominent abrasion platform and associated shoreline cutoff are observed in the subsurface from ~ 72 to 53 m below present sea level. These erosional features appear to have formed between Melt Water Pulse 1A and Melt Water Pulse 1B, when the rate of sea-level rise was lower. There are three distinct sedimentary units mapped above a regional angular unconformity interpreted to be the Holocene transgressive surface in the seismic data. Unit I, the deepest unit, is interpreted as a lag deposit that infills a topographic low associated with an abrasion platform. Unit I thins seaward by downlap and pinches out landward against the shoreline cutoff. Unit II is a mid-shelf lag deposit formed from shallower eroded material and thins seaward by downlap and landward by onlap. The youngest, Unit III, is interpreted to represent modern sediment deposition. Faults in the study area do not appear to offset the transgressive surface. The Newport Inglewood/Rose Canyon fault system is active in other regions to the south (e.g., La Jolla) where it offsets the transgressive surface and creates seafloor relief. Several shoals observed along the transgressive surface could record minor deformation due to fault activity in the study area. Nevertheless, our preferred interpretation is that the shoals are regions more resistant to erosion during marine transgression. The Cristianitos fault zone also causes a shoaling of the transgressive surface. This may be from resistant antecedent topography due to an early phase of compression on the fault. The Cristianitos fault zone was previously defined as a down-to-the-north normal fault, but the folding and faulting architecture imaged in the CHIRP data are more consistent with a strike-slip fault with a down-to-the-northwest dip-slip component. A third area of shoaling is observed off of San Mateo and San Onofre creeks. This shoaling has a constructional component and could be a relict delta or beach structure. (C) 2015 Elsevier B.V. All rights reserved.