Austin chalk yields oil near basaltic cone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-09-03

This paper reports on the completion of a Cretaceous Austin chalk horizontal oil well near a basaltic cone in the Uvalde volcanic field area of Dimmit County, Tex. The well is the HDP Inc. 1 autumn Unit, about 9 miles northeast to Carrizo Springs HDP, which stands for horizontal development and production, of Palo Alto, Calif., drilled the well on a farmout from American Exploration Co., Houston. It initially pumped and flowed 1,600 b/d of oil without stimulation from openhole. HDP drilled about 1,500 ft of horizontal and deviated hole in Austin chalk B-1, the producing horizon. Production in latemore » August was about 500 b/d of oil, pending determination of proration unit size and allowable. The well, in the greater Pearsall field Austin chalk play along the Dimmit-Savala county line, is the first horizontal chalk producer in Elaine field. The field has produced mainly from Escondido sand, Olmos sand and Anacacho limestone, all in the Upper Cretaceous.« less

Recovery of Fresh Water Resources from Desalination of Brine Produced During Oil and Gas Production Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

David B. Burnett; Mustafa Siddiqui

2006-12-29

Management and disposal of produced water is one of the most important problems associated with oil and gas (O&G) production. O&G production operations generate large volumes of brine water along with the petroleum resource. Currently, produced water is treated as a waste and is not available for any beneficial purposes for the communities where oil and gas is produced. Produced water contains different contaminants that must be removed before it can be used for any beneficial surface applications. Arid areas like west Texas produce large amount of oil, but, at the same time, have a shortage of potable water. Amore » multidisciplinary team headed by researchers from Texas A&M University has spent more than six years is developing advanced membrane filtration processes for treating oil field produced brines The government-industry cooperative joint venture has been managed by the Global Petroleum Research Institute (GPRI). The goal of the project has been to demonstrate that treatment of oil field waste water for re-use will reduce water handling costs by 50% or greater. Our work has included (1) integrating advanced materials into existing prototype units and (2) operating short and long-term field testing with full size process trains. Testing at A&M has allowed us to upgrade our existing units with improved pre-treatment oil removal techniques and new oil tolerant RO membranes. We have also been able to perform extended testing in 'field laboratories' to gather much needed extended run time data on filter salt rejection efficiency and plugging characteristics of the process train. The Program Report describes work to evaluate the technical and economical feasibility of treating produced water with a combination of different separation processes to obtain water of agricultural water quality standards. Experiments were done for the pretreatment of produced water using a new liquid-liquid centrifuge, organoclay and microfiltration and ultrafiltration membranes for the removal of hydrocarbons from produced water. The results of these experiments show that hydrocarbons from produced water can be reduced from 200 ppm to below 29 ppm level. Experiments were also done to remove the dissolved solids (salts) from the pretreated produced water using desalination membranes. Produced water with up to 45,000 ppm total dissolved solids (TDS) can be treated to agricultural water quality water standards having less than 500 ppm TDS. The Report also discusses the results of field testing of various process trains to measure performance of the desalination process. Economic analysis based on field testing, including capital and operational costs, was done to predict the water treatment costs. Cost of treating produced water containing 15,000 ppm total dissolved solids and 200 ppm hydrocarbons to obtain agricultural water quality with less than 200 ppm TDS and 2 ppm hydrocarbons range between $0.5-1.5 /bbl. The contribution of fresh water resource from produced water will contribute enormously to the sustainable development of the communities where oil and gas is produced and fresh water is a scarce resource. This water can be used for many beneficial purposes such as agriculture, horticulture, rangeland and ecological restorations, and other environmental and industrial application.« less

Assessing Produced Water Management Issues with Increasing U.S. Tight Oil Production

NASA Astrophysics Data System (ADS)

Scanlon, B. R.; Reedy, R. C.; Murray, K. E.; Weingarten, M.

2017-12-01

U.S. oil fields have been producing about 10 times more water than oil for decades; however, problems with managing this produced water, including over-pressuring and induced seismicity, have only become apparent with the recent increases in oil production from unconventional reservoirs. This study involved quantifying spatial and temporal variability in produced water volumes and evaluating issues with managing this produced water using data from the major U.S. unconventional/conventional oil plays (Bakken, Permian, and Eagle Ford plays, and Oklahoma). The primary difference between recent and historical produced water management is the inability to inject the produced water back into the unconventional low permeability or dewatered oil reservoirs. Disposing of this produced water into non-oil producing horizons using salt water disposal wells has been linked to over-pressuring in shallow geologic units in the Bakken and Permian basins and to induced seismicity in Oklahoma. These issues with produced water management can be partially alleviated by reusing/recycling produced water for hydraulic fracturing, which seems particularly promising in the Permian Basin.

Characterizing tight-gas systems with production data: Wyoming, Utah, and Colorado

USGS Publications Warehouse

Nelson, Philip H.; Santus, Stephen L.; Baez, Luis; Beeney, Ken; Sonnenberg, Steve

2013-01-01

The study of produced fluids allows comparisons among tight-gas systems. This paper examines gas, oil, and water production data from vertical wells in 23 fields in five Rocky Mountain basins of the United States, mostly from wells completed before the year 2000. Average daily rates of gas, oil, and water production are determined two years and seven years after production begins in order to represent the interval in which gas production declines exponentially. In addition to the daily rates, results are also presented in terms of oil-to-gas and water-to-gas ratios, and in terms of the five-year decline in gas production rates and water-to-gas ratios. No attempt has been made to estimate the ultimate productivity of wells or fields. The ratio of gas production rates after seven years to gas production rates at two years is about one-half, with median ratios falling within a range of 0.4 to 0.6 in 16 fields. Oil-gas ratios show substantial variation among fields, ranging from dry gas (no oil) to wet gas to retrograde conditions. Among wells within fields, the oil-gas ratios vary by a factor of three to thirty, with the exception of the Lance Formation in Jonah and Pinedale fields, where the oil-gas ratios vary by less than a factor of two. One field produces water-free gas and a large fraction of wells in two other fields produce water-free gas, but most fields have water-gas ratios greater than 1 bbl/mmcf—greater than can be attributed to water dissolved in gas in the reservoir— and as high as 100 bbl/mmcf. The median water-gas ratio for fields increases moderately with time, but in individual wells water influx relative to gas is erratic, increasing greatly with time in many wells while remaining constant or decreasing in others.

Congo (Brazzaville) Country Analysis Brief

EIA Publications

2014-01-01

Congo (Brazzaville) is among the top five oil producers in Sub-Saharan Africa. Oil production comes almost entirely from offshore oil fields. Congo exports almost all of its oil production, and the largest recipients are China and the European Union.

Occidental conserves Libyan gas by reinjection into oil reservoir

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cozens, E.T.

1972-04-24

As a leading producer in the Libyan Arab Republic, Occidental Petroleum Corp. is vitally concerned with conservation of gas produced along with the oil. Important among the manifestations of this concern is the use of residue gas from a processing plant for injection into an oil-producing reservoir. The miscible drive created by the gas will increase ultimate recovery, and the processing plant recovers LP gas and condensate for sale. Following discovery of the 103-A in 1967, Occidental moved quickly to install production equipment and a 40-in. pipeline to Zueitina, 135 miles distant on the Mediterranean. By Feb. 1968, the firstmore » oil was loaded into tankers. Discovery of C and D fields in the 103 concession followed shortly. The three 103 fields plus an original discovery in the 102 concession increased Occidental's oil rate to more than 700,000 bpd by 1970. Facilities in the Intisar A and D fields each consist of a centralized separator system containing 3 stages of separation, plus degassing boots and surge tanks. The terminal at Zueitina includes 8,000,000 bbl of oil storage. The gas processing, the products pipeline, and other aspects of the industrial plant are discussed in detail.« less

Dineh Bi Keyah. may be major Arizona strike

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The new Dineh Bi Keyah oil field lying in the Chuska Mts. of Apache County, in the NE. corner of Arizona, looms as a major Arizona field development following testing during April of its fourth producer from the Hermosa-Molas series of the Pennsylvanian System. The field is producing more than 4,000 bbl of high-gravity oil per day ranging between 42-44$API gravity. Kerr-McGee Oil Corp., operators of the field, has filed a motion with the Arizona Oil and Gas Conservation Commission requesting 160-acre well spacing for the Lower Hermosa (Pennsylvanian) oil reservoir and a hearing has been scheduled for April 19,more » 1967. The drilling practice employed by Kerr-McGee is to set the 10-3/4-in. surface casing at 400 ft and cement with 500 sacks. Completion practices followed during field development have been to selectively perforate, using 1 shot per ft of pay zone in the Lower Hermosa section. Wells are swabbed natural, then cleaned up with MCA borehole acid treatment prior to sand oil fracturing. After load is swabbed back, the well is tubed and placed on the pump. The oil is trucked to the nearest pipeline loading point in the Shiprock area of northwestern New Mexico.« less

POISON SPIDER FIELD CHEMICAL FLOOD PROJECT, WYOMING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Douglas Arnell; Malcolm Pitts; Jie Qi

2004-11-01

A reservoir engineering and geologic study concluded that approximate 7,852,000 bbls of target oil exits in Poison Spider. Field pore volume, OOIP, and initial oil saturation are defined. Potential injection water has a total dissolved solids content of 1,275 mg/L with no measurable divalent cations. If the Lakota water consistently has no measurable cations, the injection water does not require softening to dissolve alkali. Produced water total dissolved solids were 2,835 mg/L and less than 20 mg/L hardness as the sum of divalent cations. Produced water requires softening to dissolve chemicals. Softened produced water was used to dissolve chemicals inmore » these evaluations. Crude oil API gravity varies across the field from 19.7 to 22.2 degrees with a dead oil viscosity of 95 to 280 cp at 75 F. Interfacial tension reductions of up to 21,025 fold (0.001 dyne/cm) were developed with fifteen alkaline-surfactant combinations at some alkali concentration. An additional three alkaline-surfactant combinations reduced the interfacial tension greater than 5,000 fold. NaOH generally produced the lowest interfacial tension values. Interfacial tension values of less than 0.021 dyne/cm were maintained when the solutions were diluted with produced water to about 60%. Na{sub 2}CO{sub 3} when mixed with surfactants did not reduce interfacial tension values to levels at which incremental oil can be expected. NaOH without surfactant interfacial tension reduction is at a level where some additional oil might be recovered. Most of the alkaline-surfactant-polymer solutions producing ultra low interfacial tension gave type II- phase behavior. Only two solutions produced type III phase behavior. Produced water dilution resulted in maintenance of phase type for a number of solutions at produced water dilutions exceeding 80% dilution. The average loss of phase type occurred at 80% dilution. Linear corefloods were performed to determine relative permeability end points, chemical-rock compatibility, polymer injectivity, dynamic chemical retention by rock, and recommended injected polymer concentration. Average initial oil saturation was 0.796 Vp. Produced water injection recovered 53% OOIP leaving an average residual oil saturation of 0.375 Vp. Poison Spider rock was strongly water-wet with a mobility ratio for produced water displacing the 280 cp crude oil of 8.6. Core was not sensitive to either alkali or surfactant injection. Injectivity increased 60 to 80% with alkali plus surfactant injection. Low and medium molecular weight polyacrylamide polymers (Flopaam 3330S and Flopaam 3430S) dissolved in either an alkaline-surfactant solution or softened produced water injected and flowed through Poison Spider rock. Recommended injected polyacrylamide concentration is 2,100 mg/L for both polymers for a unit mobility ratio. Radial corefloods were performed to evaluate oil recovery efficiency of different chemical solutions. Waterflood oil recovery averaged 46.4 OOIP and alkaline-surfactant-polymer flood oil recovery averaged an additional 18.1% OIP for a total of 64.6% OOIP. Oil cut change due to injection of a 1.5 wt% Na{sub 2}CO{sub 3} plus 0.05 wt% Petrostep B-100 plus 0.05 wt% Stepantan AS1216 plus 2100 mg/L Flopaam 3430S was from 2% to a peak of 23.5%. Additional study might determine the impact on oil recovery of a lower polymer concentration. An alkaline-surfactant-polymer flood field implementation outline report was written.« less

Is the Bakken Formation the Answer to our Energy Independence?

NASA Astrophysics Data System (ADS)

Waggoner, E. G.; Hall, C.

2012-12-01

The Bakken Formation has garnered substantial attention due to an unprecedented surge in US domestic oil production, much of it from shale oil from the Bakken. The sheer size of the formation coupled with technological advances in horizontal drilling and hydraulic fracking have led many, including the former head of BP, to speculate that domestic shale oil will free the US from its dependence upon foreign oil entirely. Shale oil is indeed likely to provide a significant contribution to our domestic energy portfolio, but real problems exist in the form of physical limitations. Our preliminary analysis indicates that the most important fields in the Bakken Formation are depleting rapidly. Mckenzie and Mountrail Counties, the two largest oil producing counties in North Dakota, account for over 50% of North Dakota's total oil production. However, Mountrail County appears to have hit peak production between the months of March and April 2012. The decline is especially apparent in the Mountrail County's two largest producing fields, suggesting that much of production occurs in concentrated areas and many of these fields with high profitability are undergoing rapid production declines. In order to maintain a consistent level of production and offset these growing declines, an increasing number of wells must be drilled throughout the lifetime of a field. Energy Return on Investment (EROI), the ratio of energy outputs over energy inputs, can be utilized to determine the profitability of resource base. Preliminary EROI analysis indicates that newly developed fields in the Bakken are less profitable and yield far less energy than the larger producing predecessors such as those in Mountrail County. Will the smaller fields ultimately compensate for the steep declines witnessed in the larger fields? If current trends continue, ultimate production from the Bakken will be far less than predicted. This poses significant financial implications for the future of shale oil and US energy independence.

Kern River steam expansion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rintoul, B.

1970-09-15

The newest addition to Getty Oil Co.'s imposing array of steam equipment at Kern River is a 240-million-btu-per-hr boiler. This boiler is almost 5 times more powerful than the previous largest piece of steam-generating hardware in use in the field. The huge boiler went into operation in Aug. on the Canfield Fee property on Sec. 29, 28S-28E. It is being used to furnish steam for 60 wells in a displacement project. The components that have made Getty Oil Co. the leading steamer at Kern River and the field, in turn, the world capital for oil-field steam operations include shallow wells,more » steam generators, and--since last year--a computer. There are more than 4,500 oil wells in the Kern River field, including more than 2,600 on Getty Oil properties. Getty Oil's steam operations involve 2,469 producing wells and 151 injection wells, including 2,167 producing wells in stimulation projects and 302 producing wells in displacement projects. The Kern River drilling program for 1970 consists of 313 wells of which 179 are steam-injection wells for the expansion of displacement projects. Wells are shallow, drilled mainly to the Kern River Series sands at an average depth of 900 ft, with a few drilled to the China Grade zone at an average depth of 1,300 ft. To furnish steam for the massive Kern River program, Getty Oil has assembled a force of 96 steam generators.« less

43 CFR 2621.0-3 - Authority.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., potash, oil, gas, asphaltic minerals, oil shale, sodium, and sulphur and lands withdrawn by Executive... geologic structure of a producing oil or gas field may be selected except to the extent that the selection...

43 CFR 2621.0-3 - Authority.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., potash, oil, gas, asphaltic minerals, oil shale, sodium, and sulphur and lands withdrawn by Executive... geologic structure of a producing oil or gas field may be selected except to the extent that the selection...

43 CFR 2621.0-3 - Authority.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., potash, oil, gas, asphaltic minerals, oil shale, sodium, and sulphur and lands withdrawn by Executive... geologic structure of a producing oil or gas field may be selected except to the extent that the selection...

Chemical and Microbial Characterization of North Slope Viscous Oils to Assess Viscosity Reduction and Enhanced Recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shirish Patil; Abhijit Dandekar; Mary Beth Leigh

2008-12-31

A large proportion of Alaska North Slope (ANS) oil exists in the form of viscous deposits, which cannot be produced entirely using conventional methods. Microbially enhanced oil recovery (MEOR) is a promising approach for improving oil recovery for viscous deposits. MEOR can be achieved using either ex situ approaches such as flooding with microbial biosurfactants or injection of exogenous surfactant-producing microbes into the reservoir, or by in situ approaches such as biostimulation of indigenous surfactant-producing microbes in the oil. Experimental work was performed to analyze the potential application of MEOR to the ANS oil fields through both ex situ andmore » in situ approaches. A microbial formulation containing a known biosurfactant-producing strain of Bacillus licheniformis was developed in order to simulate MEOR. Coreflooding experiments were performed to simulate MEOR and quantify the incremental oil recovery. Properties like viscosity, density, and chemical composition of oil were monitored to propose a mechanism for oil recovery. The microbial formulation significantly increased incremental oil recovery, and molecular biological analyses indicated that the strain survived during the shut-in period. The indigenous microflora of ANS heavy oils was investigated to characterize the microbial communities and test for surfactant producers that are potentially useful for biostimulation. Bacteria that reduce the surface tension of aqueous media were isolated from one of the five ANS oils (Milne Point) and from rock oiled by the Exxon Valdez oil spill (EVOS), and may prove valuable for ex situ MEOR strategies. The total bacterial community composition of the six different oils was evaluated using molecular genetic tools, which revealed that each oil tested possessed a unique fingerprint indicating a diverse bacterial community and varied assemblages. Collectively we have demonstrated that there is potential for in situ and ex situ MEOR of ANS oils. Future work should focus on lab and field-scale testing of ex situ MEOR using Bacillus licheniformis as well as the biosurfactant-producing strains we have newly isolated from the Milne Point reservoir and the EVOS environment.« less

Rehabilitation and development Tarakan Island

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rowley, K.G.

1973-11-01

Tarakan is situated off the NE. coast of Kalimantan, approx. 75 miles south of Tawau, just across the border in Sabah, and about 400 miles north of Balikpapan. A closer view of the Island shows it to be somewhat pork-chop shaped. One major oil field has been discovered to date on Tarakan and 6 other minor areas of oil production have been located. The Pamusian field is discussed from which approx. 181,000,000 bbl of oil has been produced from about 1,100 total wells. Pamusian produces or has produced from formations as shallow as 180 ft to as deep as 7,000more » ft. However, almost all of the cumulative production has come from zones above 1,800 ft. It is only since early 1972 that commercial oil production has been established below 3,000 ft.« less

Reservoir characterization and preliminary modeling of deltaic facies, lower Wilcox, Concordia Parish, Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schenewerk, P.; Goddard, D.; Echols, J.

The decline in production in several fields in Concordia Parish, Louisiana, has created interest in the economic feasibility of producing the remaining bypassed oil in the lower Wilcox Group. One of these fields, Bee Brake, has been one of the more prolific oil-producing fields in east-central Louisiana. The producing interval, the Minter sandstones, at a depth of about 6,775 ft typically consists of an upper Bee Brake sandstone and a lower Angelina sandstone. A detailed study of a conventional core in the center of the field reveals a 15-ft-thick Minter interval bounded above and below by sealing shales and lignitesmore » of lower delta plain marsh facies. The upper 4-ft-thick Bee Brake is a very fine silty sandstone with characteristics of a small overbank or crevasse splay deposit. The lower 3-ft-thick oil-producing Angelina sandstone consists of very fine and fine sandstone of probable overbank or crevasse facies. Cumulative production from the Angelina is about 1.8 million stock-tank barrels of oil. Special core analysis data (capillary pressure, relative permeability, and waterflood recovery) have been used to develop a simulation model of the two reservoirs in the Minter. This model incorporates the geologic and engineering complexities noted during evaluation of the field area. Operators can use the model results in this field to design an optimal development plan for enhanced recovery.« less

Hydrocarbon-water interactions during brine migration: Evidence from hydrocarbon inclusions in calcite cements from Danish North Sea oil fields

USGS Publications Warehouse

Jensenius, J.; Burruss, R.C.

1990-01-01

Crude oils in primary and secondary fluid inclusions in calcite from fractures in seven offshore oil fields associated with diapiric salt structures in the Danish sector of the North Sea were analyzed by capillary column gas chromatography and compared with crude oils produced from the same reservoirs. Oils from fluid inclusions in all fields show evidence of biodegradation (decreased n-C17/pristane and n-C18/phytane ratios and loss of n-C7, 2-methyl hexane, and 3-methyl hexane relative to methyl cyclohexane) and water washing (absence of benzene and depletion of toluene). Some oils in inclusions are extremely enriched in C6 and C7 cyclic alkanes suggesting that these samples contain hydrocarbons exsolved from ascending, hotter formation waters. Compared to inclusion oils the produced oils are less biodegraded, but are water washed, indicating that both types of oil interacted with large volumes of formation water. The carbon isotopic composition of the calcite host of the fluid inclusions in the Dagmar and Skjold fields is as light as -16.5%. PDB and the sulfur isotopic composition of pyrite in and adjacent to the calcite veins in the Skjold field is as light as -39.6%. CDT, indicating that biodegradation of the oils was a source of some of the carbon in the calcite and sulfate reduction was the source of sulfur for the pyrite. The evidence for microbial degradation of petroleum is consistent with present-day reservoir temperatures (65??-96??C) but is not consistent with previous estimates of the temperatures of calcite vein filling (95??-130??C) which are much higher than the temperatures of known occurrences of biodegraded oil. ?? 1990.

Hydrocarbon-water interactions during brine migration: Evidence from hydrocarbon inclusions in calcite cements from Danish North Sea oil fields

NASA Astrophysics Data System (ADS)

Jensenius, Jørgen; Burruss, Robert C.

1990-03-01

Crude oils in primary and secondary fluid inclusions in calcite from fractures in seven offshore oil fields associated with diapiric salt structures in the Danish sector of the North Sea were analyzed by capillary column gas chromatography and compared with crude oils produced from the same reservoirs. Oils from fluid inclusions in all fields show evidence of biodegradation (decreased n- C17/pristane and n- C18/phytane ratios and loss of n-C 7, 2-methyl hexane, and 3-methyl hexane relative to methyl cyclohexane) and water washing (absence of benzene and depletion of toluene). Some oils in inclusions are extremely enriched in C 6 and C 7 cyclic alkanes suggesting that these samples contain hydrocarbons exsolved from ascending, hotter formation waters. Compared to inclusion oils the produced oils are less biodegraded, but are water washed, indicating that both types of oil interacted with large volumes of formation water. The carbon isotopic composition of the calcite host of the fluid inclusions in the Dagmar and Skjold fields is as light as -16.5%. PDB and the sulfur isotopic composition of pyrite in and adjacent to the calcite veins in the Skjold field is as light as -39.6%. CDT, indicating that biodegradation of the oils was a source of some of the carbon in the calcite and sulfate reduction was the source of sulfur for the pyrite. The evidence for microbial degradation of petroleum is consistent with present-day reservoir temperatures (65°-96°C) but is not consistent with previous estimates of the temperatures of calcite vein filling (95°-130°C) which are much higher than the temperatures of known occurrences of biodegraded oil.

The geochemistry of oils and gases from the Cumberland overthrust sheet in Virginia and Tennessee: Chapter G.12 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Dennen, Kristen O.; Deering, Mark; Burruss, Robert A.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

This study presents high-resolution gas chromatograms of oils and molecular and isotopic analyses of oil-associated gases from 17 wells producing in the Upper Cambrian to Lower Ordovician Knox Group, the Middle and Upper Ordovician Stones River Group, and the Upper Ordovician Trenton Limestone in the Cumberland overthrust sheet. The wells are located in the Ben Hur and Rose Hill fields in Lee County, Va., and in the Swan Creek field in Hancock and Claiborne Counties, Tenn. They produce oils typical of those from source rocks that are rich in Gloeocapsomorpha prisca (G. prisca) (Assemblage A-type kerogen). The Rose Hill oils appear to come from a source that contains a higher proportion of Assemblage A-type kerogen than the Ben Hur and Swan Creek oils. Extrapolation of the δ13C compositions of oil-associated gases to possible kerogen compositions gives estimates of -23 to -24 per mil within the range of isotopic compositions of known G. prisca source material. Gases produced from the Knox Group wells in the Swan Creek field are different from those in the Middle and Upper Ordovician reservoirs and come from a source with a broader range of isotopic values. Trends in isotopic and gasoline-range compositional parameters of the oils and associated gas isotopic and molecular compositions are most likely influenced by changes in local source depositional facies.

Hydrocarbonaceous material processing methods and apparatus

DOEpatents

Brecher, Lee E [Laramie, WY

2011-07-12

Methods and apparatus are disclosed for possibly producing pipeline-ready heavy oil from substantially non-pumpable oil feeds. The methods and apparatus may be designed to produce such pipeline-ready heavy oils in the production field. Such methods and apparatus may involve thermal soaking of liquid hydrocarbonaceous inputs in thermal environments (2) to generate, though chemical reaction, an increased distillate amount as compared with conventional boiling technologies.

Cyclic steaming in heavy oil diatomite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, M.; Beatty, F.D.

1995-12-31

Chevron currently uses cyclic steaming as a recovery method to produce economically its heavy oil diatomite resource in the Cymric field, San Joaquin Valley, California. A highly instrumented, cyclically steaming well from this field was simulated in this study to delineate important production mechanisms, to optimize operations, and to improve reservoir management. The model was constrained, as much as possible, by the available measured data. Results show that fluid flow from the well to the reservoir is primarily through the hydraulic fracture induced by the injected steam. Parameters with unique importance to modeling cyclic steaming in diatomites are: (1) inducedmore » fracture dimension (length and height), (2) matrix permeability, (3) oil/water capillary pressure, (4) grid size perpendicular to fracture face, and (5) producing bottomhole pressures. Additionally, parameters important for conventional steam injection processes, such as relative permeabilities and injected steam volume, quality, and rate, are important for diatomites also. Oil production rates and steam/oil ratios calculated by this model compare reasonably with field data.« less

Reservoir characterization and modeling of deltaic facies, Lower Wilcox, Concordia Parish, Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schenewerk, P.; Goddard, D.; Echols, J.

Production decline in several fields in Concordia Parish, Louisiana, has sparked interest in the economic feasibility of producing the remaining bypassed oil in the lower Wilcox. One of these fields, the Bee Brake field, located in townships 4N, 6E and 4N, 7E, has been one of the more prolific oil-producing areas in east central Louisiana. The producing interval in the field, the Minter, typically consists of an upper Bee Brake sand and a lower Angelina sand. Cumulative production from the Angelina has been 2.1 mm STB of oil. A detailed study of a conventional core in the center of themore » field presented a 15-ft-thick Minter interval bounded above and below by sealing shales and lignites of lower delta plain marsh facies. The lower oil producing 3-ft thick Angelina consists of fine to medium sandstone of overbank bay fill facies. The upper 4-ft thick Bee Brake is a very fine silty sandstone with characteristics of a crevasse splay deposit. Special core analysis data (capillary pressure, relative permeability, and waterflood recovery) were obtained and have been used to develop a simulation model of the two reservoirs in the Minter. This model incorporates the geologic and engineering complexities noted during the first comprehensive evaluation of the field area. The model results will be used by the operators in the field to plan the optimal development for enhanced recovery. In addition, the production potential of the Bee Brake sand has been defined.« less

Simulating surface oil transport during the Deepwater Horizon oil spill: Experiments with the BioCast system

NASA Astrophysics Data System (ADS)

Jolliff, Jason Keith; Smith, Travis A.; Ladner, Sherwin; Arnone, Robert A.

2014-03-01

The U.S. Naval Research Laboratory (NRL) is developing nowcast/forecast software systems designed to combine satellite ocean color data streams with physical circulation models in order to produce prognostic fields of ocean surface materials. The Deepwater Horizon oil spill in the Gulf of Mexico provided a test case for the Bio-Optical Forecasting (BioCast) system to rapidly combine the latest satellite imagery of the oil slick distribution with surface circulation fields in order to produce oil slick transport scenarios and forecasts. In one such sequence of experiments, MODIS satellite true color images were combined with high-resolution ocean circulation forecasts from the Coupled Ocean-Atmosphere Mesoscale Prediction System (COAMPS®) to produce 96-h oil transport simulations. These oil forecasts predicted a major oil slick landfall at Grand Isle, Louisiana, USA that was subsequently observed. A key driver of the landfall scenario was the development of a coastal buoyancy current associated with Mississippi River Delta freshwater outflow. In another series of experiments, longer-term regional circulation model results were combined with oil slick source/sink scenarios to simulate the observed containment of surface oil within the Gulf of Mexico. Both sets of experiments underscore the importance of identifying and simulating potential hydrodynamic conduits of surface oil transport. The addition of explicit sources and sinks of surface oil concentrations provides a framework for increasingly complex oil spill modeling efforts that extend beyond horizontal trajectory analysis.

Mississippian Lodgepole Play, Williston Basin: A review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Montgomery, S.L.

1996-06-01

Waulsortian-type carbonate mud mounds in the lower Mississippian Lodgepole formation (Bottineau interval, Madison Group) comprise an important new oil play in the Williston basin with strong regional potential. The play is typified by wells capable of producing 1000-2500 bbl of oil per day and by reserves that have as much as 0.5-3.0 million bbl of oil per well. Currently centered in Stark County, North Dakota, along the southern flank of the basin, the play includes 38 wells, with 21 producers and 6 new fields. Initial discovery was made at a Silurian test in Dickinson field, traditionally productive from Pennsylvanian sands.more » The largest pool discovered to date is Eland field, which has 15 producers and estimated total reserves of 12-15 million bbl. This report summarizes geologic, well-log, seismic, and production data for this play, which promises to expand considerably in the years to come.« less

Biological treatment process for removing petroleum hydrocarbons from oil field produced waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tellez, G.; Khandan, N.

1995-12-31

The feasibility of removing petroleum hydrocarbons from oil fields produced waters using biological treatment was evaluated under laboratory and field conditions. Based on previous laboratory studies, a field-scale prototype system was designed and operated over a period of four months. Two different sources of produced waters were tested in this field study under various continuous flow rates ranging from 375 1/D to 1,800 1/D. One source of produced water was an open storage pit; the other, a closed storage tank. The TDS concentrations of these sources exceeded 50,000 mg/l; total n-alkanes exceeded 100 mg/l; total petroleum hydrocarbons exceeded 125 mg/l;more » and total BTEX exceeded 3 mg/l. Removals of total n-alkanes, total petroleum hydrocarbons, and BTEX remained consistently high over 99%. During these tests, the energy costs averaged $0.20/bbl at 12 bbl/D.« less

Development of a thin oil rim with horizontal wells in a low relief chalk gas field, Tyra field, Danish North Sea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nykjaer, O.

1994-12-31

This paper presents the history of the development of an oil rim in a chalk gas field. In a low relief gas field, oil rim development is problematic because the proximity to fluid contacts leads to gas and water coning and a significantly decreased oil production. This problem has been reduced in Tyra by developing the oil rim with horizontal wells. The best oil wells are in areas where gas production is impaired by tight chalk immediately above the gas-oil contact, and where the oil rim is thickest. The field was initially developed as a gas field due to poormore » production tests of the oil rim during the appraisal of the field. An understanding of the distribution of oil led to the drilling of a successful oil rim well. The advent of horizontal drilling increased the scope for oil rim development and accelerated the drilling of oil rim wells. Extensive reservoir simulation work provided the reservoir management tool for the planning of an oil rim development under the constraint of a gas sales agreement. It has resulted in a plan for further development of the Tyra gas field. According to the plan additional gas injection will in a period of seven years result in low net annual gas off-take from the Tyra gas production wells and the main production will instead come from horizontal wells in the oil-rim. During this time the majority of the oil reserves will be produced.« less

Major Oil Plays In Utah And Vicinity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas Chidsey

2007-12-31

Utah oil fields have produced over 1.33 billion barrels (211 million m{sup 3}) of oil and hold 256 million barrels (40.7 million m{sup 3}) of proved reserves. The 13.7 million barrels (2.2 million m3) of production in 2002 was the lowest level in over 40 years and continued the steady decline that began in the mid-1980s. However, in late 2005 oil production increased, due, in part, to the discovery of Covenant field in the central Utah Navajo Sandstone thrust belt ('Hingeline') play, and to increased development drilling in the central Uinta Basin, reversing the decline that began in the mid-1980s.more » The Utah Geological Survey believes providing play portfolios for the major oil-producing provinces (Paradox Basin, Uinta Basin, and thrust belt) in Utah and adjacent areas in Colorado and Wyoming can continue this new upward production trend. Oil plays are geographic areas with petroleum potential caused by favorable combinations of source rock, migration paths, reservoir rock characteristics, and other factors. The play portfolios include descriptions and maps of the major oil plays by reservoir; production and reservoir data; case-study field evaluations; locations of major oil pipelines; identification and discussion of land-use constraints; descriptions of reservoir outcrop analogs; and summaries of the state-of-the-art drilling, completion, and secondary/tertiary recovery techniques for each play. The most prolific oil reservoir in the Utah/Wyoming thrust belt province is the eolian, Jurassic Nugget Sandstone, having produced over 288 million barrels (46 million m{sup 3}) of oil and 5.1 trillion cubic feet (145 billion m{sup 3}) of gas. Traps form on discrete subsidiary closures along major ramp anticlines where the depositionally heterogeneous Nugget is also extensively fractured. Hydrocarbons in Nugget reservoirs were generated from subthrust Cretaceous source rocks. The seals for the producing horizons are overlying argillaceous and gypsiferous beds in the Jurassic Twin Creek Limestone, or a low-permeability zone at the top of the Nugget. The Nugget Sandstone thrust belt play is divided into three subplays: (1) Absaroka thrust - Mesozoic-cored shallow structures, (2) Absaroka thrust - Mesozoic-cored deep structures, and (3) Absaroka thrust - Paleozoic-cored shallow structures. Both of the Mesozoic-cored structures subplays represent a linear, hanging wall, ramp anticline parallel to the leading edge of the Absaroka thrust. Fields in the shallow Mesozoic subplay produce crude oil and associated gas; fields in the deep subplay produce retrograde condensate. The Paleozoic-cored structures subplay is located immediately west of the Mesozoic-cored structures subplays. It represents a very continuous and linear, hanging wall, ramp anticline where the Nugget is truncated against a thrust splay. Fields in this subplay produce nonassociated gas and condensate. Traps in these subplays consist of long, narrow, doubly plunging anticlines. Prospective drilling targets are delineated using high-quality, two-dimensional and three-dimensional seismic data, forward modeling/visualization tools, and other state-of-the-art techniques. Future Nugget Sandstone exploration could focus on more structurally complex and subtle, thrust-related traps. Nugget structures may be present beneath the leading edge of the Hogsback thrust and North Flank fault of the Uinta uplift. The Jurassic Twin Creek Limestone play in the Utah/Wyoming thrust belt province has produced over 15 million barrels (2.4 million m{sup 3}) of oil and 93 billion cubic feet (2.6 billion m{sup 3}) of gas. Traps form on discrete subsidiary closures along major ramp anticlines where the low-porosity Twin Creek is extensively fractured. Hydrocarbons in Twin Creek reservoirs were generated from subthrust Cretaceous source rocks. The seals for the producing horizons are overlying argillaceous and clastic beds, and non-fractured units within the Twin Creek. The Twin Creek Limestone thrust belt play is divided into two subplays: (1) Absaroka thrust-Mesozoic-cored structures and (2) Absaroka thrust - Paleozoic-cored structures. The Mesozoic-cored structures subplay represents a linear, hanging wall, ramp anticline parallel to the leading edge of the Absaroka thrust. Fields in this subplay produce crude oil and associated gas. The Paleozoic-cored structures subplay is located immediately west of the Mesozoic-cored structures subplay. It represents a very continuous and linear, hanging wall, ramp anticline where the Twin Creek is truncated against a thrust splay. Fields in this subplay produce nonassociated gas and condensate. Traps in both subplays consist of long, narrow, doubly plunging anticlines.« less

Alcorn wells bolster Philippines oil production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-09-21

This paper reports that Alcorn International Inc., Houston, is producing about 16,500 b/d of oil from West Linapacan A field in the South China Sea off the Philippines. The field's current production alone is more than fivefold the Philippines' total average oil flow of 3,000 b/d in 1991. It's part of a string of oil and gas strikes off Palawan Island that has made the region one of the hottest exploration/development plays in the Asia-Pacific theater.

The Effectiveness of Nitrate-Mediated Control of the Oil Field Sulfur Cycle Depends on the Toluene Content of the Oil

PubMed Central

Suri, Navreet; Voordouw, Johanna; Voordouw, Gerrit

2017-01-01

The injection of nitrate is one of the most commonly used technologies to impact the sulfur cycle in subsurface oil fields. Nitrate injection enhances the activity of nitrate-reducing bacteria, which produce nitrite inhibiting sulfate-reducing bacteria (SRB). Subsequent reduction of nitrate to di-nitrogen (N2) alleviates the inhibition of SRB by nitrite. It has been shown for the Medicine Hat Glauconitic C (MHGC) field, that alkylbenzenes especially toluene are important electron donors for the reduction of nitrate to nitrite and N2. However, the rate and extent of reduction of nitrate to nitrite and of nitrite to nitrogen have not been studied for multiple oil fields. Samples of light oil (PNG, CPM, and Tundra), light/heavy oil (Gryphon and Obigbo), and of heavy oil (MHGC) were collected from locations around the world. The maximum concentration of nitrate in the aqueous phase, which could be reduced in microcosms inoculated with MHGC produced water, increased with the toluene concentration in the oil phase. PNG, Gryphon, CPM, Obigbo, MHGC, and Tundra oils had 77, 17, 5.9, 4.0, 2.6, and 0.8 mM toluene, respectively. In incubations with 49 ml of aqueous phase and 1 ml of oil these were able to reduce 22.2, 12.3, 7.9, 4.6, 4.0, and 1.4 mM of nitrate, respectively. Nitrate reduced increased to 35 ± 4 mM upon amendment of all these oils with 570 mM toluene prior to incubation. Souring control by nitrate injection requires that the nitrate is directed toward oxidation of sulfide, not toluene. Hence, the success of nitrate injections will be inversely proportional to the toluene content of the oil. Oil composition is therefore an important determinant of the success of nitrate injection to control souring in a particular field. PMID:28620357

Geochemical analysis of reservoir continuity and connectivity, Arab-D and Hanifa Reservoirs, Abqaiq Field, Saudia Arabia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mahdi, A.A.; Grover, G.; Hwang, R.

1995-08-01

Organic geochemistry and its integration with geologic and reservoir engineering data is becoming increasingly utilized to assist geologists and petroleum engineers in solving production related problems. In Abqaiq Field of eastern Saudi Arabia, gas chromatographic analysis (FSCOT) of produced oils from the Arab-D and Hanifa reservoirs was used to evaluate vertical and lateral continuity within and between these reservoirs. Bulk and molecular properties of produced Arab-D oils do not vary significantly over the 70 km length and 10 km width of the reservoir. Hanifa oils, however, do reflect two compositionally distinct populations that are hot in lateral communication, compatible withmore » the occurrence of a large oil pool in the southern part of the field, and a separate, and smaller northern accumulation. The Arab-D and underlying Hanifa oil pools are separated by over 450 feet of impermeable carbonates of the Jubaila Formation, yet the Southern Hanifa pool and the Arab-D have been in pressure communication since onset of Hanifa production in 1954. Recent borehole imaging and core data from horizontal Hanifa wells confirmed the long suspected occurrence of fractures responsible for fluid transmissibility within the porous (up to 35%) but tight (<10md matrix K) Hanifa reservoir, and between the Hanifa and Arab-D. The nearly identical hydrocarbon composition of oils from the Arab-D and southern Hanifa pool provided the final confirmation of fluid communication between the two reservoirs, and extension of a Hanifa fracture-fault network via the Jubaila Formation. This work lead to acquisition of 3-D seismic to image and map the fracture-fault system. The molecular fingerprinting approach demonstrated that produced oils can be used to evaluate vertical and lateral reservoir continuity, and at Abqaiq Field confirmed, in part, the need to produce the Hanifa reservoir via horizontal wells to arrest the reservoir communication that occurs with existing vertical wells.« less

30 CFR 1206.53 - How do I determine value for oil that I or my affiliate do(es) not sell under an arm's-length...

Code of Federal Regulations, 2011 CFR

2011-07-01

... sales to the same gravity as that of the oil produced from the lease. Use applicable gravity adjustment tables for the field (or the same general area for like-quality oil if you do not have gravity adjustment tables for the specific field) to normalize for gravity. Example to paragraph (b): 1. Assume that a...

30 CFR 1206.53 - How do I determine value for oil that I or my affiliate do(es) not sell under an arm's-length...

Code of Federal Regulations, 2012 CFR

2012-07-01

... sales to the same gravity as that of the oil produced from the lease. Use applicable gravity adjustment tables for the field (or the same general area for like-quality oil if you do not have gravity adjustment tables for the specific field) to normalize for gravity. Example to paragraph (b): 1. Assume that a...

30 CFR 1206.53 - How do I determine value for oil that I or my affiliate do(es) not sell under an arm's-length...

Code of Federal Regulations, 2013 CFR

2013-07-01

... sales to the same gravity as that of the oil produced from the lease. Use applicable gravity adjustment tables for the field (or the same general area for like-quality oil if you do not have gravity adjustment tables for the specific field) to normalize for gravity. Example to paragraph (b): 1. Assume that a...

30 CFR 1206.53 - How do I determine value for oil that I or my affiliate do(es) not sell under an arm's-length...

Code of Federal Regulations, 2014 CFR

2014-07-01

... sales to the same gravity as that of the oil produced from the lease. Use applicable gravity adjustment tables for the field (or the same general area for like-quality oil if you do not have gravity adjustment tables for the specific field) to normalize for gravity. Example to paragraph (b): 1. Assume that a...

Angola Country Analysis Brief

EIA Publications

2016-01-01

Angola is the second-largest oil producer in sub-Saharan Africa, behind Nigeria. The country experienced an oil production boom between 2002 and 2008 when production started at several deepwater fields.

Enhanced oil recovery utilizing high-angle wells in the Frontier Formation, Badger Basin Field, Park County, Wyoming. Final technical progress report, October 21, 1992--December 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, J.P.; Fortmann, R.G.

1995-03-21

Badger Basin Field was discovered in 1931. Production is principally from low-permeability fractured sandstones of the Upper Cretaceous Frontier Formation. Though many wells initially produced at about 100 barrels of oil per day or more, they now produce at stripper rates. Only about 12% of the estimated 25 million barrels of oil originally in-place will be produced from the twenty-two attempted vertical completions. The goal of this joint project between Sierra Energy Company (Sierra) and the US Department of Energy (DOE) was to recover addition reserves at economic rates through the use of 3D seismic and horizontal drilling and completingmore » techniques.« less

Secondary oil recovery from selected Carter sandstone oilfields--Black Warrior Basin, Alabama. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, J.C.

1995-02-01

Producibility problems, such as low reservoir pressure and reservoir heterogeneity, have severely limited oil production from the Central Bluff and North Fairview fields. Specific objectives for this project were: To successfully apply detailed geologic and engineering studies with conventional waterflood technologies to these fields in an effort to increase the ultimate economic recovery of oil from Carter sandstone fields; To extensively model, test and evaluate these technologies; thereby, developing a sound methodology for their use and optimization; and To team with Advanced Resources International and the US DOE to assimilate and transfer the information and results gathered from this studymore » to other oil companies to encourage the widespread use of these technologies. At Central Bluff, water injection facilities were constructed and water injection into one well began in January 1993. Oil response from the waterflood has been observed at both producing wells. One of the producing wells has experienced early water breakthrough and a concomitant drop in secondary oil rate. A reservoir modeling study was initiated to help develop an appropriate operating strategy for Central Bluff. For the North Fairview unit waterflood, a previously abandoned well was converted for water injection which began in late June 1993. The reservoir is being re-pressurized, and unit water production has remained nil since flood start indicating the possible formation of an oil bank. A reservoir simulation to characterize the Carter sand at North Fairview was undertaken and the modeling results were used to forecast field performance. The project was terminated due to unfavorable economics. The factors contributing to this decision were premature water breakthrough at Central Bluff, delayed flood response at North Fairview and stalled negotiations at the South Bluff site.« less

Azerbaijan Country Analysis Brief

EIA Publications

2016-01-01

Azerbaijan, one of the oldest oil-producing countries in the world, is an important oil and natural gas supplier in the Caspian Sea region, particularly for European markets. Although traditionally it has been a prolific oil producer, Azerbaijan's importance as a natural gas supplier will grow in the future as field development and export infrastructure expand. Conflicting claims over the maritime and seabed boundaries of the Caspian Sea between Azerbaijan and Iran continue to cause uncertainty.

The space-time structure of oil and gas field growth in a complex depositional system

USGS Publications Warehouse

Drew, L.J.; Mast, R.F.; Schuenemeyer, J.H.

1994-01-01

Shortly after the discovery of an oil and gas field, an initial estimate is usually made of the ultimate recovery of the field. With the passage of time, this initial estimate is almost always revised upward. The phenomenon of the growth of the expected ultimate recovery of a field, which is known as "field growth," is important to resource assessment analysts for several reasons. First, field growth is the source of a large part of future additions to the inventory of proved reserves of crude oil and natural gas in most petroliferous areas of the world. Second, field growth introduces a large negative bias in the forecast of the future rates of discovery of oil and gas fields made by discovery process models. In this study, the growth in estimated ultimate recovery of oil and gas in fields made up of sandstone reservoirs formed in a complex depositional environment (Frio strand plain exploration play) is examined. The results presented here show how the growth of oil and gas fields is tied directly to the architectural element of the shoreline processes and tectonics that caused the deposition of the individual sand bodies hosting the producible hydrocarbon. ?? 1994 Oxford University Press.

Horizontal drilling potential of the Cane Creek Shale, Paradox Formation, Utah

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, C.D.; Chidsey, T.C.

1991-06-01

The Cane Creek shale of the Pennsylvanian Paradox Formation is a well-defined target for horizontal drilling. This unit is naturally fractures and consists of organic-rich marine shale with interbedded dolomitic siltstone and anhydrite. Six fields have produced oil from the Cane Creek shale in the Paradox basin fold-and-fault belt. The regional structural trend is north-northwest with productive fractures occurring along the crest and flanks of both the larger and more subtle smaller anticlines. The Long Canyon, Cane Creek, Bartlett Flat, and Shafer Canyon fields are located on large anticlines, while Lion Mesa and Wilson Canyon fields produce from subtle structuralmore » noses. The Cane Creek shale is similar to the highly productive Bakken Shale in the Williston basin. Both are (1) proven producers of high-gravity oil, (2) highly fractured organic-rich source rocks, (3) overpressured, (4) regionally extensive, and (5) solution-gas driven with little or no associated water. Even though all production from the Cane Creek shale has been from conventional vertical wells, the Long Canyon 1 well has produced nearly 1 million bbl of high-gravity, low-sulfur oil. Horizontal drilling may result in the development of new fields, enhance recovery in producing fields, and revive production in abandoned fields. In addition, several other regionally extensive organic-rich shale beds occur in the Paradox Formation. The Gothic and Chimney Rock shales for example, offer additional potential lying above the Cane Creek shale.« less

Sulfate-reducing bacteria release barium and radium from naturally occurring radioactive material in oil-field barite

USGS Publications Warehouse

Phillips, E.J.P.; Landa, E.R.; Kraemer, T.; Zielinski, R.

2001-01-01

Scale and sludge deposits formed during oil production can contain elevated levels of Ra, often coprecipitated with barium sulfate (barite). The potential for sulfate-reducing bacteria to release 226 Ra and Ba (a Ra analog) from oil-field barite was evaluated. The concentration of dissolved Ba increased when samples containing pipe scale, tank sludge, or oil-field brine pond sediment were incubated with sulfate-reducing bacteria Desulfovibrio sp., Str LZKI, isolated from an oil-field brine pond. However, Ba release was not stoichiometric with sulfide production in oil-field samples, and <0.1% of the Ba was released. Potential for the release of 226Ra was demonstrated, and the 226 Ra release associated with sulfate-reducing activity was predictable from the amount of Ba released. As with Ba, only a fraction of the 226Ra expected from the amount of sulfide produced was released, and most of the Ra remained associated with the solid material.

Oil field experiments of microbial improved oil recovery in Vyngapour, West Siberia, Russia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murygina, V.P.; Mats, A.A.; Arinbasarov, M.U.

1995-12-31

Experiments on microbial improved oil recovery (MIOR) have been performed in the Vyngapour oil field in West Siberia for two years. Now, the product of some producing wells of the Vyngapour oil field is 98-99% water cut. The operation of such wells approaches an economic limit. The nutritious composition containing local industry wastes and sources of nitrogen, phosphorus and potassium was pumped into an injection well on the pilot area. This method is called {open_quotes}nutritional flooding.{close_quotes} The mechanism of nutritional flooding is based on intensification of biosynthesis of oil-displacing metabolites by indigenous bacteria and bacteria from food industry wastes inmore » the stratum. 272.5 m{sup 3} of nutritious composition was introduced into the reservoir during the summer of 1993, and 450 m3 of nutritious composition-in 1994. The positive effect of the injections in 1993 showed up in 2-2.5 months and reached its maximum in 7 months after the injections were stopped. By July 1, 1994, 2,268.6 tons of oil was produced over the base variant, and the simultaneous water extraction reduced by 33,902 m{sup 3} as compared with the base variant. The injections in 1994 were carried out on the same pilot area.« less

Economics and the 1995 National Assessment of United States Oil and Gas Resources

USGS Publications Warehouse

Attanasi, E.D.

1998-01-01

This report summarizes the economic component of the 1995 National Assessment of Oil and Gas Resources prepared by the U.S. Geological Survey for onshore and State offshore areas of the United States. Province and regional incremental cost functions for conventional undiscovered oil and gas fields, and selected unconventional oil and gas accumulations, allowing the ranking of areas by the incremental costs finding, developing, and producing these resources. Regional projections of additions to reserves from previously discovered fields to 2015 are also presented.

Pennsylvanian carbonate buildups, Paradox basin: Increasing reserves in heterogeneous, shallow-shelf reservoirs

USGS Publications Warehouse

Montgomery, S.L.; Chidsey, T.C.; Eby, D.E.; Lorenz, D.M.; Culham, W.E.

1999-01-01

Productive carbonate buildups of Pennsylvanian age in the southern Paradox basin, Utah, contain up to 200 million bbl remaining oil potentially recoverable by enhanced recovery methods. These buildups comprise over 100 satellite fields to the giant Greater Aneth field, where secondary recovery operations thus far have been concentrated. Several types of satellite buildups exist and produce oil from the Desert Creek zone of the Paradox Formation. Many of the relevant fields have undergone early abandonment; wells in Desert Creek carbonate mounds commonly produce at very high initial rates (>1000 bbl/day) and then suffer precipitous declines. An important new study focused on the detailed characterization of five separate reservoirs has resulted in significant information relevant to their future redevelopment. Completed assessment of Anasazi field suggests that phylloid algal mounds, the major productive buildup type in this area, consist of ten separate lithotypes and can be described in terms of a two-level reservoir system with an underlying high-permeability mound-core interval overlain by a lower permeability but volumetrically larger supramound (mound capping) interval. Reservoir simulations and related performance predictions indicate that CO2 flooding of these reservoirs should have considerable success in recovering remaining oil reserves.Productive carbonate buildups of Pennsylvanian age in the southern Paradox basin, Utah, contain up to 200 million bbl remaining oil potentially recoverable by enhanced recovery methods. These buildups comprise over 100 satellite fields to the giant Greater Aneth field, where secondary recovery operations thus far have been concentrated. Several types of satellite buildups exist and produce oil from the Desert Creek zone of the Paradox Formation. Many of the relevant fields have undergone early abandonment; wells in Desert Creek carbonate mounds commonly produce at very high initial rates (>1000 bbl/day) and then suffer precipitous declines. An important new study focused on the detailed characterization of five separate reservoirs has resulted in significant information relevant to their future redevelopment. Completed assessment of Anasazi field suggests that phylloid algal mounds, the major productive buildup type in this area, consist of ten separate lithotypes and can be described in terms of a two-level reservoir system with an underlying high-permeability mound-core interval overlain by a lower permeability but volumetrically larger supramound (mound capping) interval. Reservoir simulations and related performance predictions indicate that CO2 flooding of these reservoirs should have considerable success in recovering remaining oil reserves.

Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama. Final report, March 1996--September 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.

1998-12-01

This project was designed to analyze the structure of Mesozoic and Tertiary strata in Gilbertown Field and adjacent areas to suggest ways in which oil recovery can be improved. The Eutaw Formation comprises 7 major flow units and is dominated by low-resistivity, low-contrast play that is difficult to characterize quantitatively. Selma chalk produces strictly from fault-related fractures that were mineralized as warm fluid migrated from deep sources. Resistivity, dipmeter, and fracture identification logs corroborate that deformation is concentrated in the hanging-wall drag zones. New area balancing techniques were developed to characterize growth strata and confirm that strain is concentrated inmore » hanging-wall drag zones. Curvature analysis indicates that the faults contain numerous fault bends that influence fracture distribution. Eutaw oil is produced strictly from footwall uplifts, whereas Selma oil is produced from fault-related fractures. Clay smear and mineralization may be significant trapping mechanisms in the Eutaw Formation. The critical seal for Selma reservoirs, by contrast, is where Tertiary clay in the hanging wall is juxtaposed with poorly fractured Selma chalk in the footwall. Gilbertown Field can be revitalized by infill drilling and recompletion of existing wells. Directional drilling may be a viable technique for recovering untapped oil from Selma chalk. Revitalization is now underway, and the first new production wells since 1985 are being drilled in the western part of the field.« less

Drilling Productivity Report

EIA Publications

2017-01-01

Energy Information Administration’s (EIA) new Drilling Productivity Report (DPR) takes a fresh look at oil and natural gas production, starting with an assessment of how and where drilling for hydrocarbons is taking place. The DPR uses recent data on the total number of drilling rigs in operation along with estimates of drilling productivity and estimated changes in production from existing oil and natural gas wells to provide estimated changes in oil and natural gas production for six key fields. EIA's approach does not distinguish between oil-directed rigs and gas-directed rigs because once a well is completed it may produce both oil and gas; more than half of the wells produce both.

Electrodeless direct current dielectrophoresis using reconfigurable field-shaping oil barriers.

PubMed

Thwar, Prasanna K; Linderman, Jennifer J; Burns, Mark A

2007-12-01

We demonstrate dielectrophoretic (DEP) potential wells using pairs of insulating oil menisci to shape the DC electric field. These oil menisci are arranged in a configuration similar to the quadrupolar electrodes, typically used in DEP, and are shown to produce similar field gradients. While the one-pair well produces a focusing effect on particles in flow, the two-pair well results in creating spatial traps against crossflows. Uncharged polystyrene particles were used to map the DEP force fields and the experimental observations were compared against the field profiles obtained by numerically solving Maxwell's equations. We demonstrate trapping of a single particle due to negative DEP against a pressure-driven crossflow. This can be easily extended to trap and hold cells and other objects against flow for a longer time. We also show the results of particle trapping experiments performed to observe the effect of adjusting the oil menisci and the gap between two pairs of menisci in a four-menisci configuration on the nature of the DEP well formed at the center. A design parameter, Theta, capturing the dimensions of the DEP energy well, is defined and simulations exploring the effects of different geometric features on Theta are presented.

Can Producing Oil Store Carbon? Greenhouse Gas Footprint of CO2EOR, Offshore North Sea.

PubMed

Stewart, R Jamie; Haszeldine, R Stuart

2015-05-05

Carbon dioxide enhanced oil recovery (CO2EOR) is a proven and available technology used to produce incremental oil from depleted fields while permanently storing large tonnages of injected CO2. Although this technology has been used successfully onshore in North America and Europe, there are currently no CO2EOR projects in the United Kingdom. Here, we examine whether offshore CO2EOR can store more CO2 than onshore projects traditionally have and whether CO2 storage can offset additional emissions produced through offshore operations and incremental oil production. Using a high-level Life Cycle system approach, we find that the largest contribution to offshore emissions is from flaring or venting of reproduced CH4 and CO2. These can already be greatly reduced by regulation. If CO2 injection is continued after oil production has been optimized, then offshore CO2EOR has the potential to be carbon negative--even when emissions from refining, transport, and combustion of produced crude oil are included. The carbon intensity of oil produced can be just 0.056-0.062 tCO2e/bbl if flaring/venting is reduced by regulation. This compares against conventional Saudi oil 0.040 tCO2e/bbl or mined shale oil >0.300 tCO2e/bbl.

Effects of No. 2 fuel oil on hatchability of marine and estuarine bird eggs

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, D.H.; King, K.A.; Coon, N.C.

1979-01-01

Eggs of Louisiana herons, sandwich terns, and laughing gulls were oiled with either 0, 5, or 20 ..mu..1 of No. 2 fuel oil in the field and in the laboratory. After 5 days of natural incubation, field-oiled and control eggs were opened and embryonic mortality was determined. No. 2 fuel oil produced 61% mortality in Louisiana heron eggs, 56% in sandwich tern eggs, and 83% in laughing gull eggs. Hatching success of artificially incubated, oiled eggs appeared to be lower than in control eggs. However, stress during shipment to the laboratory and problems within the incubator probably contributed to reducedmore » hatchability in both groups.« less

40 CFR 147.1952 - Aquifer exemptions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... II enhanced recovery injection activities only. (1) The Sugar Run and Bradford series of oil...) Those portions of the following oil bearing aquifers, which would otherwise meet the definition of a... Watsonville) Pools. (2) The Bradford Third oil producing sand of the Guffey Field in McKean County. (3) The...

INNOVATIVE MIOR PROCESS UTILIZING INDIGENOUS RESERVOIR CONSTITUENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

D.O. Hitzman; S.A. Bailey

This research program is directed at improving the knowledge of reservoir ecology and developing practical microbial solutions for improving oil production. The goal is to identify indigenous microbial populations which can produce beneficial metabolic products and develop a methodology to stimulate those select microbes with inorganic nutrient amendments to increase oil recovery.This microbial technology has the capability of producing multiple oil releasing agents. The potential of the system will be illustrated and demonstrated by the example of biopolymer production on oil recovery. Research has begun on the program and experimental laboratory work is underway. Polymer-producing cultures have been isolated frommore » produced water samples and initially characterized. Concurrently, a microcosm scale sand-packed column has been designed and developed for testing cultures of interest, including polymer-producing strains. In research that is planned to begin in future work, comparative laboratory studies demonstrating in situ production of microbial products as oil recovery agents will be conducted in sand pack and cores with synthetic and natural field waters at concentrations, flooding rates, and with cultures and conditions representative of oil reservoirs.« less

Large axial actuation of pre-stretched tubular dielectric elastomer and use of oil encapsulation to enhance dielectric breakdown strength

NASA Astrophysics Data System (ADS)

Lau, Gih-Keong; Di-Teng Tan, Desmond; La, Thanh-Giang

2015-04-01

Rolled dielectric elastomer actuators (DEAs) are subjected to necking and non-uniform deformation upon pre-stress relaxation. Though rolled up from flat DEAs, they performed much poorer than the flat ones. Their electrically induced axial strains were previously reported as not more than 37.3%, while the flat ones produced greater than 100% strain. Often, the rolled DEAs succumb to premature breakdown before they can realize the full actuation potential like the flat ones do. This study shows that oil encapsulation, together with large hoop pre-stretch, helps single-wound rolled DEAs, which are also known as tubular DEAs, suppress premature breakdown. Consequently, the oil-encapsulated tubular DEAs can sustain higher electric fields, and thus produce larger isotonic strain and higher isometric stress change. Under isotonic testing, they sustained very high electric fields of up to 712.7 MV m-1, which is approximately 50% higher than those of the dry tubular DEAs. They produced up to 55.4% axial isotonic strain despite axially stiffening by the passive oil capsules. In addition, due to the use of large hoop pre-stretch, even the dry tubular DEAs without oil encapsulation achieved a very large axial strain of up to 84.2% compared to previous works. Under isometric testing, the oil-encapsulated tubular DEA with enhanced breakdown strength produced an axial stress change of up to nearly 0.6 MPa, which is 114% higher than that produced by the dry ones. In conclusion, the oil encapsulation and large pre-stretch help realize fuller actuation potential of tubular dielectric elastomer, which is subjected to initially non-uniform deformation.

Development of an In Situ Biosurfactant Production Technology for Enhanced Oil Recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

M.J. McInerney; R.M. Knapp; Kathleen Duncan

The long-term economic potential for enhanced oil recovery (EOR) is large with more than 300 billion barrels of oil remaining in domestic reservoirs after conventional technologies reach their economic limit. Actual EOR production in the United States has never been very large, less than 10% of the total U. S. production even though a number of economic incentives have been used to stimulate the development and application of EOR processes. The U.S. DOE Reservoir Data Base contains more than 600 reservoirs with over 12 billion barrels of unrecoverable oil that are potential targets for microbially enhanced oil recovery (MEOR). Ifmore » MEOR could be successfully applied to reduce the residual oil saturation by 10% in a quarter of these reservoirs, more than 300 million barrels of oil could be added to the U.S. oil reserve. This would stimulate oil production from domestic reservoirs and reduce our nation's dependence on foreign imports. Laboratory studies have shown that detergent-like molecules called biosurfactants, which are produced by microorganisms, are very effective in mobilizing entrapped oil from model test systems. The biosurfactants are effective at very low concentrations. Given the promising laboratory results, it is important to determine the efficacy of using biosurfactants in actual field applications. The goal of this project is to move biosurfactant-mediated oil recovery from laboratory investigations to actual field applications. In order to meet this goal, several important questions must be answered. First, it is critical to know whether biosurfactant-producing microbes are present in oil formations. If they are present, then it will be important to know whether a nutrient regime can be devised to stimulate their growth and activity in the reservoir. If biosurfactant producers are not present, then a suitable strain must be obtained that can be injected into oil reservoirs. We were successful in answering all three questions. The specific objectives of the project were (1) to determine the prevalence of biosurfactant producers in oil reservoirs, and (2) to develop a nutrient regime that would stimulate biosurfactant production in the oil reservoir.« less

The Big Mountain oil field, Ventura, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hall, E.A.

1967-06-02

The Big Mt. oil field is believed to be primarily a fault trap accumulation. All faults are hidden beneath the unconformity at the base of the Vaqueros Formation, or die out before reaching the surface. The Sespe Formation is divided into an upper sandy unit, a middle alternating sand and shale unit, and a lower sandy unit in the Big Mt. area. The producing zone is in the upper portion of the lower sandy unit. The sands are soft and friable, medium to coarse, and the reservoir characteristics are relatively good. The geology is similar to that observed in manymore » Sespe fields, such as the Oxnard and Montalvo oil fields, and the SE. portion of the South Mt. oil field. These fields are broken into many fault blocks and different production characteristics in each block. Good wells and poor ones are interspersed, with good wells downdip from poor ones and visa versa. The Big Mt. field is shallow, drilling and production costs are relatively inexpensive, and there is no royalty burden on the oil.« less

Geology and ground-water resources of Winkler County, Texas

USGS Publications Warehouse

Garza, Sergio; Wesselman, John B.

1963-01-01

The chemical quality of the water in the principal aquifers is generally acceptable for industry and for public supply. About two-thirds of the samples collected from fresh-water wells had a dissolved-solids content of less than 1,000 ppm (parts per million) ; however, some samples in a few areas were hard and were high in fluoride and silica. Samples from wells in polluted areas contained dissolved solids ranging from about 1,400 to 71,100 ppm. Two comprehensive analyses of water samples from the Rustler formation showed a dissolved-solids content of 18,400 ppm. and 157,000 ppm. In most of the water produced with the oil in the Hendrick oil field, the content of dissolved solids ranged from about 4,000 to about 10,000 ppm. The water produced with the oil in the rest of the oil fields in Winkler County was mainly brine.

The Utilization of the Microflora Indigenous to and Present in Oil-Bearing Formations to Selectively Plug the More Porous Zones Thereby Increasing Oil Recovery During Waterflooding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vadie, Alex A; Stephens, James O; Brown, Lewis R

1998-01-01

This project is a field demonstration of the ability of in-situ indigenous microorganisms in the North Blowhorn Creek Oil Field to reduce the flow of injection water in the more permeable zones of the reservoir, thereby diverting flow to other areas thus increasing the efficiency of the waterflood. The project is divided into three phases-Planning and Analysis (9 months), Implementation (45 months), and Technology Transfer (12 months). This report covers the fourth year of work on the project. During Phase I, cores were obtained from a newly drilled well and employed in laboratory core flood experiments to formulate the schedulemore » and amounts of nutrients to be used in the field demonstration. The field demonstration involves injecting potassium nitrate, sodium dihydrogen phosphate, and in some cases molasses, into four injector wells (Test) and monitoring the performance of surrounding producer wells. For comparative purposes, the producer wells surrounding four untreated injector wells (Control) also were monitored. Twenty-two months after the injection of nutrients into the reservoir began, three wells were drilled and cores taken therefrom were analyzed. Nitrate ions were found in cores from all three wells and cores from two of these wells also contained phosphate ions- thus demonstrating that the injected nutrients were being distributed widely in the reservoir. Microorganisms were shown to be present in cores from all three wells by cultural methods and by electron microscopy. In some sections of the cores, the number of microbes was large. Oil production volumes and water:oil ratios (WOR) of produced fluids have shown clearly that the MEOR treatment being demonstrated in this project is improving oil recovery. Of the 15 producer wells in the test patterns, seven have responded positively to the injection of microbial nutrients into the reservoir, while all eight of the producer wells only in control patterns have continued their natural decline in oil production, although one well did have some improvement in oil production due to increased water injection into a nearby injector well. Two of the wells have been abandoned because of uneconomical production. In light of these positive findings and with DOE's approval, the scope of the field demonstration was expanded in July 1997 to include six new injector wells. Two of these wells were previously control injectors while the other four injectors were not included in the original program. Of interest has been the performance of two wells in what was formerly a control pattern. Since the injector in this pattern (formerly Control Pattern 2) began receiving nutrients, two of the wells in the pattern have shown improved oil production for the last three months. While it would be premature to definitely characterize these two wells as yielding a positive response, these early results are certainly encouraging. Of special significance is the fact that over 7953 m 3 (50,022 barrels) of incremental oil have been recovered as a result of the MEOR treatment. Further, calculations show that the economic life of the field will be extended until July 2004 instead of a previously anticipated closure in Dec. 2002. This finding is particularly impressive in view of the fact that only four of the twenty injector wells in the field were treated during the first 30 months of the project. Preliminary indications are that byincreasing the number of injector wells pumping microbial nutrients into the reservoir from four to ten, more oil will be recovered and the economic life of the field will be extended even further. It should be emphasized that the above calculations do not take into account the oil being recovered from the five new wells that were drilled during the course of this project.« less

Electrostatic coalescence system with independent AC and DC hydrophilic electrodes

DOEpatents

Hovarongkura, A. David; Henry, Jr., Joseph D.

1981-01-01

An improved electrostatic coalescence system is provided in which independent AC and DC hydrophilic electrodes are employed to provide more complete dehydration of an oil emulsion. The AC field is produced between an AC electrode array and the water-oil interface wherein the AC electrode array is positioned parallel to the interface which acts as a grounded electrode. The emulsion is introduced into the AC field in an evenly distributed manner at the interface. The AC field promotes drop-drop and drop-interface coalescence of the water phase in the entering emulsion. The continuous oil phase passes upward through the perforated AC electrode array and enters a strong DC field produced between closely spaced DC electrodes in which small dispersed droplets of water entrained in the continuous phase are removed primarily by collection at hydrophilic DC electrodes. Large droplets of water collected by the electrodes migrate downward through the AC electrode array to the interface. All phase separation mechanisms are utilized to accomplish more complete phase separation.

17 CFR 210.4-10 - Financial accounting and reporting for oil and gas producing activities pursuant to the Federal...

Code of Federal Regulations, 2011 CFR

2011-04-01

... search for crude oil, including condensate and natural gas liquids, or natural gas (“oil and gas”) in...) Gathering, treating, and field processing (as in the case of processing gas to extract liquid hydrocarbons... first point at which oil, gas, or gas liquids, natural or synthetic, are delivered to a main pipeline, a...

Estimating decades-long trends in petroleum field energy return on investment (EROI) with an engineering-based model.

PubMed

Tripathi, Vinay S; Brandt, Adam R

2017-01-01

This paper estimates changes in the energy return on investment (EROI) for five large petroleum fields over time using the Oil Production Greenhouse Gas Emissions Estimator (OPGEE). The modeled fields include Cantarell (Mexico), Forties (U.K.), Midway-Sunset (U.S.), Prudhoe Bay (U.S.), and Wilmington (U.S.). Data on field properties and production/processing parameters were obtained from a combination of government and technical literature sources. Key areas of uncertainty include details of the oil and gas surface processing schemes. We aim to explore how long-term trends in depletion at major petroleum fields change the effective energetic productivity of petroleum extraction. Four EROI ratios are estimated for each field as follows: The net energy ratio (NER) and external energy ratio (EER) are calculated, each using two measures of energy outputs, (1) oil-only and (2) all energy outputs. In all cases, engineering estimates of inputs are used rather than expenditure-based estimates (including off-site indirect energy use and embodied energy). All fields display significant declines in NER over the modeling period driven by a combination of (1) reduced petroleum production and (2) increased energy expenditures on recovery methods such as the injection of water, steam, or gas. The fields studied had NER reductions ranging from 46% to 88% over the modeling periods (accounting for all energy outputs). The reasons for declines in EROI differ by field. Midway-Sunset experienced a 5-fold increase in steam injected per barrel of oil produced. In contrast, Prudhoe Bay has experienced nearly a 30-fold increase in amount of gas processed and reinjected per unit of oil produced. In contrast, EER estimates are subject to greater variability and uncertainty due to the relatively small magnitude of external energy investments in most cases.

Estimating decades-long trends in petroleum field energy return on investment (EROI) with an engineering-based model

PubMed Central

Tripathi, Vinay S.

2017-01-01

This paper estimates changes in the energy return on investment (EROI) for five large petroleum fields over time using the Oil Production Greenhouse Gas Emissions Estimator (OPGEE). The modeled fields include Cantarell (Mexico), Forties (U.K.), Midway-Sunset (U.S.), Prudhoe Bay (U.S.), and Wilmington (U.S.). Data on field properties and production/processing parameters were obtained from a combination of government and technical literature sources. Key areas of uncertainty include details of the oil and gas surface processing schemes. We aim to explore how long-term trends in depletion at major petroleum fields change the effective energetic productivity of petroleum extraction. Four EROI ratios are estimated for each field as follows: The net energy ratio (NER) and external energy ratio (EER) are calculated, each using two measures of energy outputs, (1) oil-only and (2) all energy outputs. In all cases, engineering estimates of inputs are used rather than expenditure-based estimates (including off-site indirect energy use and embodied energy). All fields display significant declines in NER over the modeling period driven by a combination of (1) reduced petroleum production and (2) increased energy expenditures on recovery methods such as the injection of water, steam, or gas. The fields studied had NER reductions ranging from 46% to 88% over the modeling periods (accounting for all energy outputs). The reasons for declines in EROI differ by field. Midway-Sunset experienced a 5-fold increase in steam injected per barrel of oil produced. In contrast, Prudhoe Bay has experienced nearly a 30-fold increase in amount of gas processed and reinjected per unit of oil produced. In contrast, EER estimates are subject to greater variability and uncertainty due to the relatively small magnitude of external energy investments in most cases. PMID:28178318

Production optimization of sucker rod pumping wells producing viscous oil in Boscan field, Venezuela

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guirados, C.; Sandoval, J.; Rivas, O.

1995-12-31

Boscan field is located in the western coast of Maracaibo lake and is operated by Maraven S.A., affiliate of Petroleos de Venezuela S.A. It has 315 active wells, 252 of which are produced with sucker rod pumping. Other artificial lift methods currently applied in this field are hydraulic (piston) pumping (39 wells) and ESP (24 wells). This paper presents the results of the production optimization of two sucker rod pumping wells of Boscan field producing viscous oil. This optimization has been possible due to the development of a new production scheme and the application of system analysis in completion design.more » The new production scheme involves the utilization of a subsurface stuffing box assembly and a slotted housing, both designed and patented by Intevep S.A., affiliate of Petroleos de Venezuela S.A. The completion design method and software used in the optimization study were also developed by Intevep S.A. The new production scheme and design method proved to be effective in preventing the causes of the above mentioned problems, allowing the increase of oil production under better operating conditions.« less

Preliminary Prioritization of California Oil and Gas Fields for Regional Groundwater Monitoring Based on Intensity of Petroleum Resource Development and Proximity to Groundwater Resources

NASA Astrophysics Data System (ADS)

Davis, T. A.; Landon, M. K.; Bennett, G.

2016-12-01

The California State Water Resources Control Board is collaborating with the U.S. Geological Survey to implement a Regional Monitoring Program (RMP) to assess where and to what degree groundwater resources may be at risk of contamination from oil and gas development activities including stimulation, well integrity issues, produced water ponds, and underground injection. A key issue in the implementation of the RMP is that the state has 487 onshore oil fields covering 8,785 square kilometers but detailed characterization work can only be done in a few oil fields annually. The first step in the RMP is to prioritize fields using available data that indicate potential risk to groundwater from oil and gas development, including vertical proximity of groundwater and oil/gas resources, density of petroleum and water wells, and volume of water injected in oil fields. This study compiled data for these factors, computed summary metrics for each oil field, analyzed statewide distributions of summary metrics, used those distributions to define relative categories of potential risk for each factor, and combined these into an overall priority ranking. Aggregated results categorized 22% (107 fields) of the total number of onshore oil and gas fields in California as high priority, 23% as moderate priority, and 55% as low priority. On an area-weighted basis, 41% of the fields ranked high, 30% moderate, and 29% low, highlighting that larger fields tend to have higher potential risk because of greater intensity of development, sometimes coupled with closer proximity to groundwater. More than half of the fields ranked as high priority were located in the southern Central Valley or the Los Angeles Basin. The prioritization does not represent an assessment of groundwater risk from oil and gas development; rather, such assessments are planned to follow based on detailed analysis of data from the RMP near the oil fields selected for study in the future.

The utilization of the microflora indigenous to and present in oil-bearing formations to selectively plug the more porous zones thereby increasing oil recovery during waterflooding. Technical progress report, January 1, 1997--December 31, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stephens, J.O.

This project is a field demonstration of the ability of in-situ indigenous microorganisms in the North Blowhorn Creek Oil Field to reduce the flow of injection water in the more permeable zones of the reservoir, thereby diverting flow to other areas thus increasing the efficiency of the waterflood. The project is divided into three phases: Planning and Analysis (9 months), Implementation (45 months), and Technology Transfer (12 months). This report covers the fourth year of work on the project. Twenty-two months after the injection of nutrients into the reservoir began, three wells were drilled and cores taken therefrom were analyzed.more » Oil production volumes and water:oil ratios (WOR) of produced fluids have shown clearly that the MEOR treatment being demonstrated in this project is improving oil recovery. Of the 15 producer wells in the test patterns, seven have responded positively to the injection of microbial nutrients into the reservoir, while all eight of the producer wells only in control patterns have continued their natural decline in oil production, although one well did have some improvement in oil production due to increased water injection into a nearby injector well. In light of these positive findings and with DOE`s approval, the scope of the field demonstration was expanded in July 1997 to include six new injector wells. Of interest has been the performance of two wells in what was formerly a control pattern. Since the injector in this pattern (formerly Control Pattern 2) began receiving nutrients, two of the wells in the pattern have shown improved oil production for the last three months. While it would be premature to definitely characterize these two wells as yielding a positive response, these early results are certainly encouraging.« less

Subsurface geology and oil and gas resources of Osage County, Oklahoma. Part 2, Townships 22 and 23 north, ranges 8 and 9 east

USGS Publications Warehouse

Kirk, C.T.; Jenkins, H.D.; Leatherock, Otto; Dillard, W.R.; Kennedy, L.E.; Bass, N.W.

1939-01-01

This report on the subsurface geology of Osage County, Okla., describes the structural features, the character of the oil- and gas-producing beds, and the localities where additional oil and gas may be found. It embodies a part of the results of a subsurface geologic investigation of the Osage Indian Reservation, which coincides in area with Osage County. The investigation was conducted by a field party of the Geological Survey of the United States Department of the Interior from 1934 to 1937 and involved the study of the records of about 17,000 wells that have been drilled in Osage County. Funds for the investigation were allotted to the Geological Survey by the Public Works Administration. The primary purpose of the examination was to obtain geologic data for use in the administration of the Indian lands. The results of the inquiry have shown that many localities in Osage County outside the present producing oil fields are worthy of prospecting for oil and gas and that additional oil and gas can be found also by exploring deeply buried beds in old producing fields.All townships in Osage County that contain many wells are described; the information furnished by such townships is ample for drawing detailed subsurface structure-contour maps. The descriptions of several contiguous townships are combined in separate reports, which are issued as parts of a single bulletin. No edition of the consolidated volume will be published, but the several parts can be bound together if desired.

Distribution and origin of groundwater methane in the Wattenberg oil and gas field of northern Colorado.

PubMed

Li, Huishu; Carlson, Kenneth H

2014-01-01

Public concerns over potential environmental contamination associated with oil and gas well drilling and fracturing in the Wattenberg field in northeast Colorado are increasing. One of the issues of concern is the migration of oil, gas, or produced water to a groundwater aquifer resulting in contamination of drinking water. Since methane is the major component of natural gas and it can be dissolved and transported with groundwater, stray gas in aquifers has elicited attention. The initial step toward understanding the environmental impacts of oil and gas activities, such as well drilling and fracturing, is to determine the occurrence, where it is and where it came from. In this study, groundwater methane data that has been collected in response to a relatively new regulation in Colorado is analyzed. Dissolved methane was detected in 78% of groundwater wells with an average concentration of 4.0 mg/L and a range of 0-37.1 mg/L. Greater than 95% of the methane found in groundwater wells was classified as having a microbial origin, and there was minimal overlap between the C and H isotopic characterization of the produced gas and dissolved methane measured in the aquifer. Neither density of oil/gas wells nor distance to oil/gas wells had a significant impact on methane concentration suggesting other important factors were influencing methane generation and distribution. Thermogenic methane was detected in two aquifer wells indicating a potential contamination pathway from the producing formation, but microbial-origin gas was by far the predominant source of dissolved methane in the Wattenberg field.

DOE Office of Scientific and Technical Information (OSTI.GOV)

French, Troy

Le Norman Energy Company conducted research on field application of alkaline-surfactant-polymer (ASP) flooding as a part of the U.S. Department of Energy's plan to maximize the production of our domestic oil resources. In addition to having substantial technical merit, the process uses chemicals that are environmentally acceptable. Le Norman's field project is located in the Sho-Vel-Tum (OK) oil field, which was a major producer of crude oil in past years, but has since been extensively waterflooded. This reservoir in this portion of the field is typical of many shallow reservoirs in the Oklahoma-Kansas area and is a good demonstration sitemore » for that area. The pay zones are located approximately 700 ft. deep, and this project is the shallowest field test for ASP flooding.« less

Aqueous Rare Earth Element Patterns and Concentration in Thermal Brines Associated With Oil and Gas Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nye, Charles; Quillinan, Scott Austin; Neupane, Ghanashyam

This study is part of a joint effort by the University of Wyoming (UW) School of Energy Resources (SER), the UW Engineering Department, Idaho National Laboratories (INL), and the United States Geological Survey (USGS) to describe rare earth element concentrations in oil and gas produced waters and in coal-fired power station ash ponds. In this work we present rare earth element (REE) and trace metal behavior in produced water from four Wyoming oil and gas fields and surface ash pond water from two coal-fired power stations. The concentration of REEs in oil and gas produced waters is largely unknown. Formore » example, of the 150,000 entries in the USGS National Produced Waters Geochemical Database less than 5 include data for REEs. Part of the reason for this scarcity is the analytical challenge of measuring REEs in high salinity, hydrocarbon-bearing waters. The industry standard for water analysis struggles to detect REEs in natural waters under ideal conditions. The detection of REEs in oil and gas field samples becomes all but impossible with the background noise and interferences caused by high concentrations of non-REE ions and residual hydrocarbons. The INL team members have overcome many of these challenges (e.g. McLing, 2014), and continue to develop their methods. Using the methods of the INL team members we measured REEs in high salinity oil and gas produced waters. Our results show that REEs exist as a dissolved species in all waters measured for this project, typically within the parts per trillion range. The samples may be grouped into two broad categories analytically, and these categories match their genesis: Wyoming oil and gas brines contain elevated levels of Europium, and Wyoming industrial pond waters show elevation in heavy REEs (HREEs). While broadly true, important variations exist within both groups. In the same field Europium can vary by more than an order of magnitude, and likewise HREEs in industrial ponds at the same site can vary by more than an order of magnitude. Future work will investigate the reasons for these variations.« less

Gas, water, and oil production from Wattenberg field in the Denver Basin, Colorado

USGS Publications Warehouse

Nelson, Philip H.; Santus, Stephen L.

2011-01-01

Gas, oil, and water production data were compiled from selected wells in two tight gas reservoirs-the Codell-Niobrara interval, comprised of the Codell Sandstone Member of the Carlile Shale and the Niobrara Formation; and the Dakota J interval, comprised mostly of the Muddy (J) Sandstone of the Dakota Group; both intervals are of Cretaceous age-in the Wattenberg field in the Denver Basin of Colorado. Production from each well is represented by two samples spaced five years apart, the first sample typically taken two years after production commenced, which generally was in the 1990s. For each producing interval, summary diagrams and tables of oil-versus-gas production and water-versus-gas production are shown with fluid-production rates, the change in production over five years, the water-gas and oil-gas ratios, and the fluid type. These diagrams and tables permit well-to-well and field-to-field comparisons. Fields producing water at low rates (water dissolved in gas in the reservoir) can be distinguished from fields producing water at moderate or high rates, and the water-gas ratios are quantified. The Dakota J interval produces gas on a per-well basis at roughly three times the rate of the Codell-Niobrara interval. After five years of production, gas data from the second samples show that both intervals produce gas, on average, at about one-half the rate as the first sample. Oil-gas ratios in the Codell-Niobrara interval are characteristic of a retrograde gas and are considerably higher than oil-gas ratios in the Dakota J interval, which are characteristic of a wet gas. Water production from both intervals is low, and records in many wells are discontinuous, particularly in the Codell-Niobrara interval. Water-gas ratios are broadly variable, with some of the variability possibly due to the difficulty of measuring small production rates. Most wells for which water is reported have water-gas ratios exceeding the amount that could exist dissolved in gas at reservoir pressure and temperature. The Codell-Niobrara interval is reported to be overpressured (that is, pressure greater than hydrostatic) whereas the underlying Dakota J interval is underpressured (less than hydrostatic), demonstrating a lack of hydraulic communication between the two intervals despite their proximity over a broad geographical area. The underpressuring in the Dakota J interval has been attributed by others to outcropping strata east of the basin. We agree with this interpretation and postulate that the gas accumulation also may contribute to hydraulic isolation from outcrops immediately west of the basin.

An overview of field-specific designs of microbial EOR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robertson, E.P.; Bala, G.A.; Fox, S.L.

1995-12-31

The selection and design of an MEOR process for application in a specific field involves geological, reservoir, and biological characterization. Microbially mediated oil recovery mechanisms (bigenic gas, biopolymers, and biosurfactants) are defined by the types of microorganisms used. The engineering and biological character of a given reservoir must be understood to correctly select a microbial system to enhance oil recovery. This paper discusses the methods used to evaluate three fields with distinct characteristics and production problems for the applicability of MEOR would not be applicable in two of the three fields considered. The development of a microbial oil recovery processmore » for the third field appeared promising. Development of a bacterial consortium capable of producing the desired metabolites was initiated, and field isolates were characterized.« less

RADIATION DOSE AND RISK TO RECREATIONAL FISHERMEN FROM INGESTION OF FISH CAUGHT NEAR EIGHT OIL PLATFORMS IN THE GULF OF MEXICO

DOE Office of Scientific and Technical Information (OSTI.GOV)

MEINHOLD,A.F.; HOLTZMAN,S.

1998-06-01

Offshore production of oil and gas is accompanied by a saline wastewater, called produced water. Produced water discharges to the Gulf of Mexico often contain elevated concentrations of radionuclides that occur naturally in the geologic reservoir along with the oil and gas. These radionuclides may accumulate in organisms that live near offshore oil and gas structures. Because recreational fishing in the Gulf of Mexico is concentrated near oil and gas platforms, there is the potential for increased risks to recreational fishermen from the ingestion of radionuclides in fish caught near produced water discharges. This analysis investigated the potential risk tomore » recreational fishermen from radium and lead-210 in offshore produced water discharges to the Gulf of Mexico. The assessment used data collected at eight discharging offshore platforms and two reference locations. These data were collected in a USDOE funded project titled ``Environmental and Economic Assessment of Discharges from Gulf of Mexico Region Oil and Gas Operations'', here called the USDOE Field Study. The risk assessments were done to support risk managers in developing regulations and permits for offshore discharges of produced water.« less

From ACTS (Air Corps Tactical School) to COBRA: Evolution of Close Air Support Doctrine in World War Two.

DTIC Science & Technology

1988-04-01

cooperated and coordinated their activities in absolute precision cieated by total nental telepathy . Although XIX Tactice.1 Air Coeeand and Third Aray did...capture of the Romanian oil fields and increased production of synthetic oil, Germany produced enough oil to meet her military needs. By 1944, the

Subsurface brine injection: Proactive approach to close the produced water loop in the western desert of Egypt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farid, E.E.; Nour, M.H.

1996-11-01

In 1988 a major onshore production facility was producing oil from eight formations in six oil fields located in the western desert of Egypt. Two of these formations include active water drive reservoirs, in addition; three reservoirs at that date were receiving water injection to enhance oil recovery. To handle the increasing volumes of the produced water (which is contaminated with oil, production chemicals and other pollutants), three alternatives were investigated: (1) Injection into disposal wells. (2) Dumping in surface disposal pits. (3) Re-injection to waterflood some oil reservoirs. The investigation revealed that the first two options are technically unfavorable,more » also they are conventional Waste Management Technologies (WMT) which provide short-term remedial solution. In contrast, Produced Water Re-Injection (PWRI) is an Environmental Control Technology (ECT) which minimize the environmental impact through process improvements. A state -of-the-art re-injection process was utilized using chemical treatment, gas liberation, settling, filtration and injection. This process represents a combination of two (ECT) methods: Reuse (for water flooding) and Recycling (when brine is redisposed underground). This process reduce the overall volumes of produced water to be disposed, increase the oil reserves, reservoir pressure and oil production and converse the underground water reserve.« less

Oil and Gas field code master list 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This is the fourteenth annual edition of the Energy Information Administration`s (EIA) Oil and Gas Field Code Master List. It reflects data collected through October 1995 and provides standardized field name spellings and codes for all identified oil and/or gas fields in the US. The Field Code Index, a listing of all field names and the States in which they occur, ordered by field code, has been removed from this year`s publications to reduce printing and postage costs. Complete copies (including the Field Code Index) will be available on the EIA CD-ROM and the EIA World-Wide Web Site. Future editionsmore » of the complete Master List will be available on CD-ROM and other electronic media. There are 57,400 field records in this year`s Oil and Gas Field Code Master List. As it is maintained by EIA, the Master List includes the following: field records for each State and county in which a field resides; field records for each offshore area block in the Gulf of Mexico in which a field resides; field records for each alias field name (see definition of alias below); and fields crossing State boundaries that may be assigned different names by the respective State naming authorities. Taking into consideration the double-counting of fields under such circumstances, EIA identifies 46,312 distinct fields in the US as of October 1995. This count includes fields that no longer produce oil or gas, and 383 fields used in whole or in part for oil or gas Storage. 11 figs., 6 tabs.« less

Hydraulic Fracturing of 403 Shallow Diatomite Wells in South Belridge Oil Field, Kern County, California, in 2014

NASA Astrophysics Data System (ADS)

Wynne, D. B.; Agusiegbe, V.

2015-12-01

We examine all 403 Hydraulic Fracture (HF) jobs performed by Aera Energy, LLC, in the South Belridge oil field, Kern County, CA in 2014. HFs in the South Belridge oil field are atypical amongst North American plays because the reservoir is shallow and produced via vertical wells. Our data set constitutes 88% of all HF jobs performed in CA oil fields in calendar-2014. The South Belridge field produces 11% of California's oil and the shallow HFs performed here differ from most HFs performed elsewhere. We discuss fracture modeling and methods and summary statistics, and modelled dimensions of fractures and their relationships to depth and reservoir properties. The 403 HFs were made in the diatomite-dominated Reef Ridge member of the Monterey Formation. The HFs began at an average depth of 1047 feet below ground (ft TVD) and extended an average of 626 ft vertically downward. The deepest initiation of HF was at 2380 ft and the shallowest cessation was at 639 ft TVD. The average HF was performed using 1488 BBL (62,496 gallons) of water. The HFs were performed in no more than 6 stages and nearly all were completed within one day. We (1) compare metrics of the South Belridge sample group with recent, larger "all-CA" and nationwide samples; and (2) conclude that if relationships of reservoir properties, well completion and HF are well understood, shallow diatomite HF may be optimized to enhance production while minimizing environmental impact.

Kitty field, Campbell County, Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, C.R.

1970-09-01

Statistical data, a table of cumulative production, a production graph, and several maps and cross sections make up this report. This is a stratigraphic trap oil field with facies and permeability barriers within the Cretaceous Muddy Sandstone reservoir. The field produces from 2 sandstones with an average pay thickness of 28 ft. Cumulative production through the first 3 mo. of 1970 is 6,757,207 bbl of oil and 11,684,884 Mcf of gas from 127 wells and from proved productive area of 13,600 acres. Ultimate primary recovery reserves are estimated to be 23,000,000 bbl of oil and 50,000,000 Mcf gas.

RELATIONSHIP OF URANIUM ORE DEPOSITS TO PETROLEUM AND GAS-BEARING STRUCTURES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, R.T.

eposits are located on producing or breached oil and gas structures, or in the immediate vicinity of such structures. Individual deposits associated with these structures contain ore reserves which may exceed one million tons. Data derived from a study of the known deposits should be useful in evaluating the potentiality of other areas where similar structural relations and abnormal radioactivity are known to exist. Uranium deposits located in producing oil or gas fields include a deposit of more than one million tons of uranium ore on a single salt dome in Texas, and uranium deposits in the Poison Basin, Wyoming,more » which are situated over a producing naturalgas structure, having a potential of 100,000 to 200,000 tons. Important uranium mining districts are also located near producing oil fields or near structures which may have contained oil at some time in the past. The Gas Hills district to Wyoming is on the flanks of a breached anticline and within one mile of natural-gas seeps. Deposits in the Brown's Park formation near Maybell, Colorado, are witin 10 miles of producing oil wells and natural-gas seeps are known within one mile of some of the uranium mines; and at Morrison, Colorado, uranium ore is associated with tar seeps. On th Colorado Plateau, large ore bodies with total reserves of at least 30 million tons of 0.3% U/sub 3/O/sub 8/ ore in the Ambrosia Lake district near Grants, New Mexico, and produce ore associated with asphaltite.'' The uraniferous asphaltite'' ore at Temple Mountain, Utah has been known for nearly 50 years. At both Circle Cliffs and the Inter- River area in Utah, uranium ore is associated with asphaltic material on anticlinal structures. Many other deposits are on breached strucIn Wyoming, uranium deposits in Tertiary sandstone and arkose generally lack carbon trash, but are located near oil or gas structures that contain hydrocarbons and natural gases capable of precititating uranium. Also, many uranium deposits on the Colorado Plateau have insufficient plant remains present to be the fixing agent for uranium, but petroleum and/or natural gas are proposed as possible extractants. The hydrogen sulfide contaned in natural gas or dissolved in oil-field water has been a factor in the formation of some uranium deposits. Oil-type structural traps must have been effective in localizing both petroleum and uranium ore in some districts. Although petroleum may contain small amounts of uranium, it is doubtful if either oil or natural gas are important transporting agents for uranium. Careful consideration of these various factors will provide a basis upon which to evaluate more effectively many ore producing areas. (auth)« less

Newburg-South Westhope oil fields, North Dakota

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marafi, H.

1972-01-01

The Newburg and South Westhope oil fields, located in Bottineau County, North Dak., in the NE. part of the Williston Basin, are excellent examples of stratigraphic traps, although structural elements are involved in trapping of the accumulations. The oil is produced from 2 adjacent zones separated by a major unconformity, and they are considered to be a common reservoir. The productive units are the ''Ratcliffe'' interval of the Mississippian Charles Formation and the Saude Member of the Triassic Spearfish Formation. Post-Paleozoic migration of the oil is indicated because, even though the Ratcliffe was exposed to considerable erosion, it is productivemore » at the unconformity.« less

Anaerobic thermophilic bacteria isolated from a Venezuelan oil field and its potential use in microbial improved oil recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trebbau, G.; Fernandez, B.; Marin, A.

1995-12-31

The objective of this work is to determine the ability of indigenous bacteria from a Venezuelan oil field to grow under reservoir conditions inside a porous media, and to produce metabolites capable of recovering residual crude oil. For this purpose, samples of formation waters from a central-eastern Venezuelan oil reservoir were enriched with different carbon sources and a mineral basal media. Formation water was used as a source of trace metals. The enrichments obtained were incubated at reservoir temperature (71{degrees}C), reservoir pressure (1,200 psi), and under anaerobic conditions for both outside and inside porous media (Berea core). Growth and metabolicmore » activity was followed outside porous media by measuring absorbance at 660 nm, increases in pressure, and decreases in pH. Inside porous media bacterial activity was determined by visual examination of the produced waters (gas bubbles and bacterial cells). All the carbohydrates tested outside porous media showed good growth at reservoir conditions. The pH was lowered, gases such as CO{sub 2} and CH{sub 4} were identified by GC. Surface tension was lowered in some enrichments by 30% when compared to controls. Growth was decreased inside porous media, but gases were produced and helped displace oil. In addition, 10% residual oil was recovered from the Berea core. Mathematical modeling was applied to the laboratory coreflood experiment to evaluate the reproducibility of the results obtained.« less

Exploration and development offshore southern Vietnam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferguson, A.M.

1996-01-01

In Vietnam, the major focus of the oil and gas industry is on the Nam Con Son and Cuu Long Basins in the southern offshore area. Major licensing first occurred here in the early 1970s. Some exploration was also undertaken by foreign companies in the early 1980s. In 1981, the Soviet Union undertook to assist Vietnam with the development of oil and gas. Vietsovpetro, a joint venture between the then Soviet Oil and Gas Ministry and the Vietnam Oil and Gas Corporation was formed. Most of Vietsovpetro's efforts have been to develop the Bach Ho field in the Cuu Longmore » Basin. This now produces [approximately]130000 bopd. The most recent large scale licensing round occurred in 1992, and, at present, there are over thirty foreign companies active in these Basins' blocks . The first phase of exploration is ending and successes in the Nam Con Son Basin include the BP-led Lan Tay/Lan Do gas discoveries and Pedco's gas discoveries. Mitsubishi's and Petronas' oil discoveries in the Cuu Long Basin have attracted much attention also. The Dai Hung oil field (BHP-operated) has been producing since late 1994. Certain blocks are being appraised, and exploration work is also continuing. Areas of the Cuu Long Basin that were part of Vietsovpetro's acreage, but which may soon be re-licensed, have generated keen interest. The presence of an active upstream industry - exploring, appraising, developing and producing - indicates the emergence of Vietnam as an important East Asian oil and gas player.« less

Petroleum geology of Cook Inlet basin - an exploration model

USGS Publications Warehouse

Magoon, L.B.; Claypool, G.E.

1981-01-01

Oil exploration commenced onshore adjacent to lower Cook Inlet on the Iniskin Peninsula in 1900, shifted with considerable success to upper Cook Inlet from 1957 through 1965, then returned to lower Cook Inlet in 1977 with the COST well and Federal OCS sale. Lower Cook Inlet COST No. 1 well, drilled to a total depth of 3,775.6 m, penetrated basinwide unconformities at the tops of Upper Cretaceous, Lower Cretaceous, and Upper Jurassic strata at 797.1, 1,540.8, and 2,112.3 m, respectively. Sandstone of potential reservoir quality is present in the Cretaceous and lower Tertiary rocks. All siltstones and shales analyzed are low (0 to 0.5 wt. %) in oil-prone organic matter, and only coals are high in humic organic matter. At total depth, vitrinite readings reached a maximum ave age reflectance of 0.65. Several indications of hydrocarbons were present. Oil analyses suggest that oils from the major fields of the Cook Inlet region, most of which produce from the Tertiary Hemlock Conglomerate, have a common source. More detailed work on stable carbon isotope ratios and the distribution of gasoline-range and heavy (C12+) hydrocarbons confirms this genetic relation among the major fields. In addition, oils from Jurassic rocks under the Iniskin Peninsula and from the Hemlock Conglomerate at the southwestern tip of the Kenai lowland are members of the same or a very similar oil family. The Middle Jurassic strata of the Iniskin Peninsula are moderately rich in organic carbon (0.5 to 1.5 wt. %) and yield shows of oil and of gas in wells and in surface seeps. Extractable hydrocarbons from this strata are similar in chemi al and isotopic composition to the Cook Inlet oils. Organic matter in Cretaceous and Tertiary rocks is thermally immature in all wells analyzed. Oil reservoirs in the major producing fields are of Tertiary age and unconformably overlie Jurassic rocks; the pre-Tertiary unconformity may be significant in exploration for new oil reserves. The unconformable relation between reservoir rocks and likely Middle Jurassic source rocks also implies a delay in the generation and expulsion of oil from Jurassic until late Tertiary when localized basin subsidence and thick sedimentary fill brought older, deeper rocks to the temperature required for petroleum generation. Reservoir porosities, crude oil properties, the type of oil field traps, and the tectonic framework of the oil fields on the west flank of the basin provide evidence used to reconstruct an oil migration route. The route is inferred to commence deep in the truncated Middle Jur ssic rocks and pass through the porous West Foreland Formation in the McArthur River field area to a stratigraphic trap in the Oligocene Hemlock Conglomerate and the Oligocene part of the Tyonek Formation at the end of Miocene time. Pliocene deformation shut off this route and created localized structural traps, into which the oil moved by secondary migration to form the Middle Ground Shoal, McArthur River, and Trading Bay oil fields. Oil generation continued into the Pliocene, but this higher API gravity oil migrated along a different route to the Granite Point field.

Oil and gas field code master list 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This is the thirteenth annual edition of the Energy Information Administration`s (EIA) Oil and Gas Field Code Master List. It reflects data collected through October 1994 and provides standardized field name spellings and codes for all identified oil and/or gas fields in the United States. The master field name spellings and codes are to be used by respondents when filing the following Department of Energy (DOE) forms: Form EIA-23, {open_quotes}Annual Survey of Domestic Oil and Gas Reserves,{close_quotes} filed by oil and gas well operators (field codes are required from larger operators only); Forms FERC 8 and EIA-191, {open_quotes}Underground Gas Storagemore » Report,{close_quotes} filed by natural gas producers and distributors who operate underground natural gas storage facilities. Other Federal and State government agencies, as well as industry, use the EIA Oil and Gas Field Code Master List as the standard for field identification. A machine-readable version of the Oil and Gas Field Code Master List is available from the National Technical Information Service, 5285 Port Royal Road, Springfield, Virginia 22161, (703) 487-4650. In order for the Master List to be useful, it must be accurate and remain current. To accomplish this, EIA constantly reviews and revises this list. The EIA welcomes all comments, corrections, and additions to the Master List. All such information should be given to the EIA Field Code Coordinator at (214) 953-1858. EIA gratefully acknowledges the assistance provides by numerous State organizations and trade associations in verifying the existence of fields and their official nomenclature.« less

The Talara Basin province of northwestern Peru: cretaceous-tertiary total petroleum system

USGS Publications Warehouse

Higley, Debra K.

2004-01-01

More than 1.68 billion barrels of oil (BBO) and 340 billion cubic feet of gas (BCFG) have been produced from the Cretaceous-Tertiary Total Petroleum System in the Talara Basin province, northwestern Peru. Oil and minor gas fields are concentrated in the onshore northern third of the province. Current production is primarily oil, but there is excellent potential for offshore gas resources, which is a mostly untapped resource because of the limited local market for gas and because there are few pipelines. Estimated mean recoverable resources from undiscovered fields in the basin are 1.71 billion barrels of oil (BBO), 4.79 trillion cubic feet of gas (TCFG), and 255 million barrels of natural gas liquids (NGL). Of this total resource, 15 percent has been allocated to onshore and 85 percent to offshore; volumes are 0.26 BBO and 0.72 TCFG onshore, and 1.45 BBO and 4.08 TCFG offshore. The mean estimate of numbers of undiscovered oil and gas fields is 83 and 27, respectively. Minimum size of fields that were used in this analysis is 1 million barrels of oil equivalent and (or) 6 BCFG. The Paleocene Talara forearc basin is superimposed on a larger, Mesozoic and pre-Mesozoic basin. Producing formations, ranging in age from Pennsylvanian to Oligocene, are mainly Upper Cretaceous through Oligocene sandstones of fluvial, deltaic, and nearshore to deep-marine depositional origins. The primary reservoirs and greatest potential for future development are Eocene sandstones that include turbidites of the Talara and Salinas Groups. Additional production and undiscovered resources exist within Upper Cretaceous, Paleocene, and Oligocene formations. Pennsylvanian Amotape quartzites may be productive where fractured. Trap types in this block-faulted basin are mainly structural or a combination of structure and stratigraphy. Primary reservoir seals are interbedded and overlying marine shales. Most fields produce from multiple reservoirs, and production is reported commingled. For this reason, and also because geochemical data on oils and source rocks is very limited, Tertiary and Cretaceous production is grouped into one total petroleum system. The most likely source rocks are Tertiary marine shales, but some of the Cretaceous marine shales are also probable source rocks, and these would represent separate total petroleum systems. Geochemical data on one oil sample from Pennsylvanian rock indicates that it was probably also sourced from Tertiary shales.

DOE tallies Class III oil recovery field projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-07-25

Here are details from midterm proposals submitted as part of the US Department of Energy's Class 3 oil recovery field demonstration candidate projects. All of the proposals emphasize dissemination of project details so that the results, if successful, can be applied widely in similar reservoirs. Project results will also be fed into a national petroleum technology transfer network. The proposals include: Gulf of Mexico, Gulf coast, offshore California, a California thermal, immiscible CO[sub 2], produced/potable water, microbial EOR, California diatomite, West Texas Spraberry field, and other Permian Basin fields.

Impact of formation water geochemistry and crude oil biodegradation on microbial methanogenesis

USGS Publications Warehouse

Shelton, Jenna L.; McIntosh, Jennifer C.; Warwick, Peter D.; McCray, John E.

2016-01-01

Shallow wells (393–442 m depth) contained highly biodegraded oils associated with low extent of methanogenesis, while the deepest (> 1208 m) wells contained minimally degraded oils and produced fluids suggesting a low extent of methanogenesis. Mid-depth wells (666–857 m) in the central field had the highest indicators of methanogenesis and contained moderately biodegraded oils. Little correlation existed between extents of crude oil biodegradation and methanogenesis across the whole transect (avg.R2 = 0.13). However, when wells with the greatest extent of crude oil biodegradation were eliminated (3 of 6 oilfields), better correlation between extent of methanogenesis and biodegradation (avg. R2 = 0.53) was observed. The results suggest that oil quality and salinity impact methanogenic crude oil biodegradation. Reservoirs indicating moderate extent of crude oil biodegradation and high extent of methanogenesis, such as the central field, would be good candidates for attempting to enhance methanogenic crude oil biodegradation as a result of the observations from the study.

Reservoir characteristics of two minter oil sands based on continuous core, E-logs, and geochemical data: Bee Brake field, East-Central Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Echols, J.B.; Goddard, D.A.; Bouma, A.

The Bee Brake field area, located in township 4N/6E and 4N/7E in Concordia Parish, has been one of the more prolific oil-producing areas in east-central Louisiana. Production decline in various fields, however, has sparked interest in the economic feasibility of locating and producing the remaining bypassed oil in the lower Wilcox. For this purpose, the Angelina BBF No. 1 well was drilled, and a 500-ft conventional core and a complete suite of state-of-the-are wireline logs were recovered. Production tests were run on the Minter interval of interest. The 16-ft Minter interval (6742-6758 ft depth), bounded at its top and basemore » by lignite seams, consists of an upper 4-ft oil sand (Bee Brake) and a lower 3-ft oil sand (Angelina). The oil sands are separated by approximately 5 ft of thinly laminated silty shale and 4 ft of very fine-grained silty sandstone. Detailed sedimentologic and petrographic descriptions of the Minter interval provide accurate facies determinations of this lower delta-plain sequence. Petrophysical evaluation, combining core plug and modern electric-log data show differences between reservoir quality of the Bee Brake and Angelina sands. This data will also be useful for correlating and interpolating old electric logs. Organic geochemistry of the oil, lignites, and shales provides insight as to the source of the Minter oils and the sourcing potential of the lignites.« less

Geology and habitat of oil in Ras Budran field, Gulf of Suez, Egypt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chowdhary, L.R.; Taha, S.

1987-05-01

Deminex discovered the Ras Budran oil field in 1978. Discovery well EE 85-1 was drilled in about 140 ft of water, 4 km off the Sinai coast of the Gulf of Suez. Appraisal drilling (EE 85-2, 3, and 4 wells) confirmed the presence of a major field with an estimated 700 million bbl oil in place. The field, developed from three wellhead platforms, went on production in April 1983. To date, 20 development wells have been drilled. The Ras Budran structure at the deepest mappable seismic reflector, top Kareem (middle Miocene), is a broad northeast-southwest-trending anticlinal feature striking nearly atmore » right angles to the main Gulf of Suez trend. At pre-Miocene producing horizons, the structure is complex and consists of a northeast-dipping flank (14-15) broken into several blocks by faults and limited to the south and west by major bounding faults. Oil is produced from three units of Nubian sandstone at a depth of 11,000 to 12,000 ft. The lower unit of Paleozoic age averages 10% porosity and up to 200 md in -situ permeability. The wells completed in this unit produce up to 2000 BOPD. In contrast, the sands of the upper two units of Lower Cretaceous age have a 15-20% porosity and up to 700 md permeability. The wells completed in these units produce 6000-8000 BOPD. The Ras Budran structure was primarily formed during the intra-Rudeis tectonic phase (lower Miocene). Migration of oil for accumulation in Ras Budran started late in the upper Miocene or Pliocene when the Santonian Brown Limestone and the Eocene Thebes Formation, the main source beds in the Gulf, reached the threshold of oil generation at a burial depth of about 10,000 ft (3000 m). At these depths, the organic matter in the source beds have a transformation ratio (0.10 to 0.15), increased yields of C15 + soluble organic matter and C15 + saturated hydrocarbons, a vitrinite reflectance of 0.62%, and a TTI value of 15.« less

Reservoir heterogeneity in Carboniferous sandstone of the Black Warrior basin. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kugler, R.L.; Pashin, J.C.; Carroll, R.E.

1994-04-01

Although oil production in the Black Warrior basin of Alabama is declining, additional oil may be produced through improved recovery strategies, such as waterflooding, chemical injection, strategic well placement, and infill drilling. High-quality characterization of reservoirs in the Black Warrior basin is necessary to utilize advanced technology to recover additional oil and to avoid premature abandonment of fields. This report documents controls on the distribution and producibility of oil from heterogeneous Carboniferous reservoirs in the Black Warrior basin of Alabama. The first part of the report summarizes the structural and depositional evolution of the Black Warrior basin and establishes themore » geochemical characteristics of hydrocarbon source rocks and oil in the basin. This second part characterizes facies heterogeneity and petrologic and petrophysical properties of Carter and Millerella sandstone reservoirs. This is followed by a summary of oil production in the Black Warrior basin and an evaluation of seven improved-recovery projects in Alabama. In the final part, controls on the producibility of oil from sandstone reservoirs are discussed in terms of a scale-dependent heterogeneity classification.« less

Calleguas Creek Simi Valley to Moorpark Ventura County, California.

DTIC Science & Technology

1976-06-01

Valley and Moorpark; (2) the elimination of flood hazard to health and safety; (3) availability of 185 acres of flood plain for urban growths ; (4...again. The outlook is high for continued production. 22. In the study area, most of the oil and gas fields are along the Oak Ridge-Santa Susana fault and...the Simi field. The Simi oil fields are relatively large. 23. Most of the commercial sand and gravel produced in Ventura County in 1972 was from the

Uzbek licensing round brings geology, potential into focus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heafford, A.P.; Lichtman, G.S.

1993-08-09

Uzbekistan is a Central Asian Republic that declared independence from the former Soviet Union in 1991. Uzbekistan produces about 18 million bbl/year of oil and 40 bcf/year of gas. It is the third largest gas producer in the Commonwealth of Independent States and imports oil. The Uzbek government and oil and gas industry are offering exploration acreage for foreign participation via competitive bid. Acreage on offer includes fields for development and unproven-underexplored areas. Terms awaiting approval by the Cabinet of Ministers provide financial incentives for rapid development of existing reserves, creation of required infrastructure, and long term investment growth. Licensemore » areas concentrate on acreage where western equipment and technology can bring new reserves economically on line in the near future. National oil company Uzbekneftegaz was created in 1992 to oversee the extraction, transport, and refining of hydrocarbons in Uzbekistan. The paper describes some of the fields and infrastructure in place, the structural geology, stratigraphy, petroleum distribution, source rocks, reservoir rocks, cap rocks, traps, and hydrocarbon composition, which includes oil, gases, and gas condensates.« less

Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama -- Year 2. Annual report, March 1997--March 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.

1998-09-01

Gilbertown Field is the oldest oil field in Alabama and has produced oil from fractured chalk of the Cretaceous Selma Group and glauconitic sandstone of the Eutaw Formation. Nearly all of Gilbertown Field is still in primary recovery, although waterflooding has been attempted locally. The objective of this project is to analyze the geologic structure and burial history of Mesozoic and Tertiary strata in Gilbertown Field and adjacent areas in order to suggest ways in which oil recovery can be improved. Indeed, the decline of oil production to marginally economic levels in recent years has made this type of analysismore » timely and practical. Key technical advancements being sought include understanding the relationship of requisite strain to production in Gilbertown reservoirs, incorporation of synsedimentary growth factors into models of area balance, quantification of the relationship between requisite strain and bed curvature, determination of the timing of hydrocarbon generation, and identification of the avenues and mechanisms of fluid transport.« less

Review of Vedder pool development, Kern River field, Kern County, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Condon, M.W.

1986-07-01

The Kern River field is located on the east side of the San Joaquin Valley, just north of Bakersfield, California. Since its discovery in 1899, the field has produced over 1 billion bbl of heavy oil from the Kern River Formation. It was not until 1981 that light oil was discovered from a deeper zone, the Vedder formation. The discovery well, Getty Oil Company WD-1 Apollo, encountered 40 ft of net oil sand within the third Vedder sand and was completed on pump for an initial production of 100 bbl of 40.5/sup 0/ API oil and 200 MCDGD. As suggestedmore » by its name, WD-1 Apollo was drilled as a water-water injection wells. However, a detailed subsurface study of the field suggested the possibility of a trap within the Vedder formation. The originally proposed location of WD-1 Apollo was then moved to test the proposal. The trap is a series of intersecting, up-to-the-basin normal faults trending west and northwest. These faults have dropped impermeable silty zones within the Vedder formation against the productive Vedder sands. Since the completion of WD-1 Apollo, nine other wells have been drilled within this pool, extending production over 1 mi to the southeast. One of the first of the extension wells, Getty Oil Company 73X Central Point, located approximately 600 ft southeast of WD-1 Apollo, established production from the second Vedder sand. This well was completed flowing 300 b/d of 32/sup 0/ API oil and 1000 MCFGD through a 16/64-in. choke. Through December 1985, Texaco (Getty Oil) produced more than 250,000 bbl of oil and 350,000 mcf of gas combined from the second and third Vedder sands from 2.5 net wells. Although attempts to find other such Vedder pools have met with limited success, there is still the potential for many to exist, given proper structural closure, as seen in the Apollo pool.« less

California producers take new steps in old fields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rintoul, B.

One of the busiest fields in California from the standpoint of well servicing work is the South Belridge field 40 miles west of Bakersfield in the San Joaquin Valley, where Shell California Production Co.'s Kernridge Division is pursuing an active program. There are 2 principal producing horizons in the South Belridge field, and the work handled by the workover and well-pulling rigs reflects the type of activity required to produce the zones. One pay consists of the Tulare sand, which produces 13- gravity oil from depths ranging from 400 to 1,200 ft. The other is the Diatomite Zone, which producesmore » a light oil averaging 28 gravity from depths ranging from 600 to 3,000 ft. Of the 29 rigs, 23 are assigned to Tulare work, 6 to Diatomite jobs. Due to the aggressive development program, Kernridge has increased production to 77,500 bpd from the 42,000 bpd. The biggest factor in the production increase from the Tulare sands is an increase in steam injection. Another factor in the production gain is increased use of hydraulic fracturing in the Diatomite zone.« less

Microbial consortia in Oman oil fields: a possible use in enhanced oil recovery.

PubMed

Al-Bahry, Saif N; Elshafie, Abdulkader E; Al-Wahaibi, Yahya M; Al-Bemani, Ali S; Joshi, Sanket J; Al-Maaini, Ratiba A; Al-Alawi, Wafa J; Sugai, Yuichi; Al-Mandhari, Mussalam

2013-01-01

Microbial enhanced oil recovery (MEOR) is one of the most economical and efficient methods for extending the life of production wells in a declining reservoir. Microbial consortia from Wafra oil wells and Suwaihat production water, Al-Wusta region, Oman were screened. Microbial consortia in brine samples were identified using denaturing gradient gel electrophoresis and 16S rRNA gene sequences. The detected microbial consortia of Wafra oil wells were completely different from microbial consortia of Suwaihat formation water. A total of 33 genera and 58 species were identified in Wafra oil wells and Suwaihat production water. All of the identified microbial genera were first reported in Oman, with Caminicella sporogenes for the first time reported from oil fields. Most of the identified microorganisms were found to be anaerobic, thermophilic, and halophilic, and produced biogases, biosolvants, and biosurfactants as by-products, which may be good candidates for MEOR.

Chemistry and origin of Miocene and Eocene oils and tars in the onshore and offshore Santa Cruz Basins, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kornacki, A.S.; McNeil, R.I.

1996-12-31

The Santa Cruz (La Honda) Basin is a small {open_quote}slice{close_quote} of the San Joaquin Basin that has been displaced c. 300 km to the northwest by the San Andreas Fault. The poorly-explored offshore area that now lies within the Monterey Bay NMS includes portions of the Outer Santa Cruz and Bodega basins. A modest amount (c. 1.3 MM bbl) of variable-quality oil has been produced from Eocene and Pliocene pay zones in the La Honda Field. Much smaller amounts of light oil ({ge}40{degrees} API) have been produced from three other fields (Oil Creek; Moody Gulch; Half Moon Bay). Large tarmore » deposits also outcrop near the city of Santa Cruz. Proven source rocks in this basin include the Eocene Twobar Shale and three Miocene units: the Lambert Shale, Monterey Formation, and the Santa Cruz Mudstone. A high-gravity oil sample from the Oil Creek Field contains isotopically-light carbon ({delta}{sup 13}C = - 28.2 per mil) and has a relatively high pristane/phytane ratio. This oil was generated at high temperature (c. 140{degrees}C) by pre-Miocene source rocks (probably the Twobar Shale). The presence of isotopically-heavy carbon in all other oil and tar samples demonstrates they were generated by Miocene source rocks. But the C{sub 7} oil-generation temperatures, sulfur content, vanadium/nickel ratios, and biomarker chemistry of these Miocene oils are significantly different than in Monterey oils from the prolific Santa Maria Basin (SMB). The sulfur content (8.0 wt%) and V-Ni chemistry of tarry petroleum recovered in the P-036-1 well (Outer Santa Cruz Basin) resembles the chemistry of very heavy (<15{degrees}API) oils generated by phosphatic Monterey shales in the SMB.« less

Chemistry and origin of Miocene and Eocene oils and tars in the onshore and offshore Santa Cruz Basins, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kornacki, A.S.; McNeil, R.I.

1996-01-01

The Santa Cruz (La Honda) Basin is a small [open quote]slice[close quote] of the San Joaquin Basin that has been displaced c. 300 km to the northwest by the San Andreas Fault. The poorly-explored offshore area that now lies within the Monterey Bay NMS includes portions of the Outer Santa Cruz and Bodega basins. A modest amount (c. 1.3 MM bbl) of variable-quality oil has been produced from Eocene and Pliocene pay zones in the La Honda Field. Much smaller amounts of light oil ([ge]40[degrees] API) have been produced from three other fields (Oil Creek; Moody Gulch; Half Moon Bay).more » Large tar deposits also outcrop near the city of Santa Cruz. Proven source rocks in this basin include the Eocene Twobar Shale and three Miocene units: the Lambert Shale, Monterey Formation, and the Santa Cruz Mudstone. A high-gravity oil sample from the Oil Creek Field contains isotopically-light carbon ([delta][sup 13]C = - 28.2 per mil) and has a relatively high pristane/phytane ratio. This oil was generated at high temperature (c. 140[degrees]C) by pre-Miocene source rocks (probably the Twobar Shale). The presence of isotopically-heavy carbon in all other oil and tar samples demonstrates they were generated by Miocene source rocks. But the C[sub 7] oil-generation temperatures, sulfur content, vanadium/nickel ratios, and biomarker chemistry of these Miocene oils are significantly different than in Monterey oils from the prolific Santa Maria Basin (SMB). The sulfur content (8.0 wt%) and V-Ni chemistry of tarry petroleum recovered in the P-036-1 well (Outer Santa Cruz Basin) resembles the chemistry of very heavy (<15[degrees]API) oils generated by phosphatic Monterey shales in the SMB.« less

A petroleum discovery-rate forecast revisited-The problem of field growth

USGS Publications Warehouse

Drew, L.J.; Schuenemeyer, J.H.

1992-01-01

A forecast of the future rates of discovery of crude oil and natural gas for the 123,027-km2 Miocene/Pliocene trend in the Gulf of Mexico was made in 1980. This forecast was evaluated in 1988 by comparing two sets of data: (1) the actual versus the forecasted number of fields discovered, and (2) the actual versus the forecasted volumes of crude oil and natural gas discovered with the drilling of 1,820 wildcat wells along the trend between January 1, 1977, and December 31, 1985. The forecast specified that this level of drilling would result in the discovery of 217 fields containing 1.78 billion barrels of oil equivalent; however, 238 fields containing 3.57 billion barrels of oil equivalent were actually discovered. This underestimation is attributed to biases introduced by field growth and, to a lesser degree, the artificially low, pre-1970's price of natural gas that prevented many smaller gas fields from being brought into production at the time of their discovery; most of these fields contained less than 50 billion cubic feet of producible natural gas. ?? 1992 Oxford University Press.

30 CFR 206.53 - How do I determine value for oil that I or my affiliate do(es) not sell under an arm's-length...

Code of Federal Regulations, 2010 CFR

2010-07-01

..., from the property where it is produced to the point where you or your affiliate purchase(s) it. You may..., for purchases or sales under arm's-length contracts. (1) When calculating that unit value, use only purchases or sales of other like-quality oil produced from the field (or the same area if you do not have...

Exploration and development offshore southern Vietnam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferguson, A.M.

1996-12-31

In Vietnam, the major focus of the oil and gas industry is on the Nam Con Son and Cuu Long Basins in the southern offshore area. Major licensing first occurred here in the early 1970s. Some exploration was also undertaken by foreign companies in the early 1980s. In 1981, the Soviet Union undertook to assist Vietnam with the development of oil and gas. Vietsovpetro, a joint venture between the then Soviet Oil and Gas Ministry and the Vietnam Oil and Gas Corporation was formed. Most of Vietsovpetro`s efforts have been to develop the Bach Ho field in the Cuu Longmore » Basin. This now produces {approximately}130000 bopd. The most recent large scale licensing round occurred in 1992, and, at present, there are over thirty foreign companies active in these Basins` blocks . The first phase of exploration is ending and successes in the Nam Con Son Basin include the BP-led Lan Tay/Lan Do gas discoveries and Pedco`s gas discoveries. Mitsubishi`s and Petronas` oil discoveries in the Cuu Long Basin have attracted much attention also. The Dai Hung oil field (BHP-operated) has been producing since late 1994. Certain blocks are being appraised, and exploration work is also continuing. Areas of the Cuu Long Basin that were part of Vietsovpetro`s acreage, but which may soon be re-licensed, have generated keen interest. The presence of an active upstream industry - exploring, appraising, developing and producing - indicates the emergence of Vietnam as an important East Asian oil and gas player.« less

Application of bio-huff-`n`-puff technology at Jilin oil field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiu-Yuan Wang; Yan-Fed Xue; Gang Dai

1995-12-31

An enriched culture 48, capable of adapting to the reservoir conditions and fermenting molasses to produce gas and acid, was used as an inoculum for bio- huff-`n`-puff tests at Fuyu oil area of Jilin oil field. The production well was injected with water containing 4-6% (v/v) molasses and inoculum, and then shut in. After 15-21 days, the well was placed back in operation. A total of 44 wells were treated, of which only two wells showed no effects. The daily oil production of treated wells increased by 33.3-733.3%. Up to the end of 1994, the oil production was increased bymore » 204 tons per well on average. Results obtained from various types of production wells were discussed.« less

Petroleum geology of Choctaw County, Alabama

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myers, J.D.

The first commercial oil production in the State of Alabama was established in Choctaw County in 1944 when H.L. Hunt discovered Gilbertown field. Gilbertown produces oil from the Selma and Eutaw formations of Upper Cretaceous Age. During 1967, Toxey field was discovered by E.L. Erickson and Choctaw Ridge was discovered by C. Pruet and D. Hughes. These 2 discoveries initiated the successful Smackover oil exploration in Choctaw County which is continuing today. This study deals primarily with the petroleum geology of the Smackover Formation of Jurassic Age. The detailed stratigraphic and structural geology of several Smackover oil fields in Choctawmore » County is examined to illustrate geological concepts developed while exploring the Smackover. Factors influencing porosity development are emphasized and suggestions are made for future exploration in the Choctaw trend of Alabama.« less

Characteristics of enriched cultures for bio-huff-`n`-puff tests at Jilin oil field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiu-Yuan Wang; Gang Dai; Yan-Fen Xue

1995-12-31

Three enriched cultures (48, 15a, and 26a), selected from more than 80 soil and water samples, could grow anaerobically in the presence of crude oil at 30{degrees}C and could ferment molasses to gases and organic acids. Oil recovery by culture 48 in the laboratory model experiment was enhanced by 25.2% over the original reserves and by 53.7% over the residual reserves. Enriched culture 48 was composed of at least 4 species belonging to the genera Eubacterium, Fusobacterium, and Bacteroides. This enriched culture was used as inoculum for MEOR field trials at Jilin oil field with satisfactory results. The importance ofmore » the role of these isolates in EOR was confirmed by their presence and behavior in the fluids produced from the microbiologically treated reservoir.« less

Gas, Oil, and Water Production from Grand Valley, Parachute, Rulison, and Mamm Creek Fields in the Piceance Basin, Colorado

USGS Publications Warehouse

Nelson, Philip H.; Santus, Stephen L.

2010-01-01

Gas, oil, and water production data for tight gas reservoirs were compiled from selected wells in western Colorado. These reservoir rocks-the relatively shallow Paleogene Wasatch G sandstone interval in the Parachute and Rulison fields and fluvial sandstones in the deeper Upper Cretaceous Mesaverde Group in the Grand Valley, Parachute, Rulison, and Mamm Creek fields-are characterized by low permeability, low porosity, and the presence of clay minerals in pore space. Production from each well is represented by two samples spaced five years apart, the first sample typically taken two years after production commenced, which was generally in the 1990s. For each producing interval, summary diagrams of oil-versus-gas and water-versus-gas production show fluid production rates, the change in rates during five years, the water-gas and oil-gas ratios, and the fluid type. These diagrams permit well-to-well and field-to-field comparisons. Fields producing water at low rates (water dissolved in gas in the reservoir) can be distinguished from fields producing water at moderate or high rates, and the water-gas ratios are quantified. Dry gas is produced from the Wasatch G interval and wet gas is produced from the Mesaverde Group. Production from the Wasatch G interval is also almost completely free of water, but water production commences with gas production in wells producing from the Mesaverde Group-all of these wells have water-gas ratios exceeding the amount that could exist dissolved in gas at reservoir temperature and pressure. The lack of produced water from the Wasatch G interval is attributed to expansion of the gas accumulation with uplift and erosion. The reported underpressure of the Wasatch G interval is here attributed to hydraulic connection to the atmosphere by outcrops in the Colorado River valley at an elevation lower than that of the gas fields. The amount of reduction of gas production over the five-year time span between the first and second samples is roughly one-half, with median values of second-sample to first-sample gas-production ratios ranging from 0.40 for Rulison-Mesaverde to 0.63 for Rulison-Wasatch G. Commencing with the first sample, the logarithm-of-production rate appears to decline linearly with time in many wells. However, water production is much more erratic as a function of time from an individual well and also from one well to the next within a field. Water production can either decrease or increase with time (from the first to the second sample). In this study, slightly more than half the wells producing from the Mesaverde Group show decreases in water production with time. Plots of water decline versus gas decline show little relation between the two, with only the wells in Rulison field displaying some tendency for water and gas to decline proportionately

Biological souring and mitigation in oil reservoirs.

PubMed

Gieg, Lisa M; Jack, Tom R; Foght, Julia M

2011-10-01

Souring in oil field systems is most commonly due to the action of sulfate-reducing prokaryotes, a diverse group of anaerobic microorganisms that respire sulfate and produce sulfide (the key souring agent) while oxidizing diverse electron donors. Such biological sulfide production is a detrimental, widespread phenomenon in the petroleum industry, occurring within oil reservoirs or in topside processing facilities, under low- and high-temperature conditions, and in onshore or offshore operations. Sulfate reducers can exist either indigenously in deep subsurface reservoirs or can be "inoculated" into a reservoir system during oil field development (e.g., via drilling operations) or during the oil production phase. In the latter, souring most commonly occurs during water flooding, a secondary recovery strategy wherein water is injected to re-pressurize the reservoir and sweep the oil towards production wells to extend the production life of an oil field. The water source and type of production operation can provide multiple components such as sulfate, labile carbon sources, and sulfate-reducing communities that influence whether oil field souring occurs. Souring can be controlled by biocides, which can non-specifically suppress microbial populations, and by the addition of nitrate (and/or nitrite) that directly impacts the sulfate-reducing population by numerous competitive or inhibitory mechanisms. In this review, we report on the diversity of sulfate reducers associated with oil reservoirs, approaches for determining their presence and effects, the factors that control souring, and the approaches (along with the current understanding of their underlying mechanisms) that may be used to successfully mitigate souring in low-temperature and high-temperature oil field operations.

Petroleum geology of Campos Basin, Brazil: A successful case history of deep water exploration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Franke, M.R.; Lugon, H.A.F.; Beraldo, W.L.

1990-05-01

Campos Basin, the most prolific Brazilian basin, produces almost 400,000 bbl of oil per day and contains 70% of the national reserves. The basin is located on the southeastern coast of Brazil, covering a prospectable area of 100,000 km{sup 2} Campos is a passive continental margin basin originated by the breakup of Pangea and the rifting of the South American and African plates in the Early Cretaceous. The basin's sedimentary section encompasses three megasequences: nonmarine, transitional, and marine, ranging in age from Neocomian to Holocene. Hydrocarbon generation is related to nonmarine organic-rich shales and marls, and hydrocarbon entrapment assumes ascendentmore » migration along fault planes and through salt gaps toward reservoirs ranging in age from Neocomian to Tertiary (mainly turbiditic sandstones). The first onshore stratigraphic well was drilled based on gravity surveys in 1958. The acquisition of new geophysical data, mainly seismic reflection data, followed after 1968. The first offshore well was drilled in 1971, and in 1974, the first oil field, Garopua, was discovered. Giant hydrocarbon accumulations have been discovered in water depths ranging from 400 to 1,800 m since 1984. As of mid-1989, 35 offshore oil fields have been discovered, 760 million bbl of oil, and 490 bcf of gas have been produced. The basin oil and equivalent gas reserves are estimated in 6.0 billion bbl, 60% of which is located in the deep-water giant oil fields.« less

Ouachitas need more exploratory drilling

USGS Publications Warehouse

Suneson, Neil H.; Campbell, Jock A.

1990-01-01

The Ouachita Mountains in southeastern Oklahoma and western Arkansas are part of a mostly buried late Paleozoic fold and thrust belt that extends from Alabama to northern Mexico. The principal hydrocarbon reservoirs in the Ouachita tectonic province can be subdivided into those that produce natural gas from shallow-water units and those that produce oil and/or natural gas from deep-water units. They can also be divided into those that are fractured and those that produce from primary pore spaces or vugs. The first successful oil well in the Ouachita Mountains was drilled in 1913 or 1914. Since the discovery of the Redden field, over 800 oil and gas wells have been drilled in the Ouachita tectonic province in Oklahoma. Yet, most of the region remains little explored.

Core Flood study for enhanced oil recovery through ex-situ bioaugmentation with thermo- and halo-tolerant rhamnolipid produced by Pseudomonas aeruginosa NCIM 5514.

PubMed

Varjani, Sunita J; Upasani, Vivek N

2016-11-01

The aim of this work was to study the Microbial Enhanced Oil Recovery (MEOR) employing core field model ex-situ bioaugmenting a thermo- and halo-tolerant rhamnolipid produced by Pseudomonas aeruginosa. Thin Layer Chromatography (TLC) revealed that the biosurfactant produced was rhamnolipid type. Nuclear Magnetic Resonance analysis showed that the purified rhamnolipids comprised two principal rhamnolipid homologues, i.e., Rha-Rha-C10-C14:1 and Rha-C8-C10. The rhamnolipid was stable under wide range of temperature (4°C, 30-100°C), pH (2.0-10.0) and NaCl concentration (0-18%, w/v). Core Flood model was designed for oil recovery operations using rhamnolipid. The oil recovery enhancement over Residual Oil Saturation was 8.82% through ex-situ bioaugmentation with rhamnolipid. The thermal stability of rhamnolipid shows promising scope for its application at conditions where high temperatures prevail in oil recovery processes, whereas its halo-tolerant nature increases its application in marine environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Wesco Operating Inc., Lander Field NPDES Proposed Permit

EPA Pesticide Factsheets

Indian Country, Minor, indust., non-discharge, proposed permit WY-0000221 establishes monitoring and reporting provisions should an unauthorized release of produced water occur from the Wesco Operating, Inc., Lander Field NW Discharge oil production site.

Nanofiltration/reverse osmosis for treatment of coproduced waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mondal, S.; Hsiao, C.L.; Wickramasinghe, S.R.

2008-07-15

Current high oil and gas prices have lead to renewed interest in exploration of nonconventional energy sources such as coal bed methane, tar sand, and oil shale. However oil and gas production from these nonconventional sources has lead to the coproduction of large quantities of produced water. While produced water is a waste product from oil and gas exploration it is a very valuable natural resource in the arid Western United States. Thus treated produced water could be a valuable new source of water. Commercially available nanofiltration and low pressure reverse osmosis membranes have been used to treat three producedmore » waters. The results obtained here indicate that the permeate could be put to beneficial uses such as crop and livestock watering. However minimizing membrane fouling will be essential for the development of a practical process. Field Emission Scanning Electron Microscopy imaging may be used to observe membrane fouling.« less

Microbial diversity in methanogenic hydrocarbon-degrading enrichment cultures isolated from a water-flooded oil reservoir (Dagang oil field, China)

NASA Astrophysics Data System (ADS)

Jiménez, Núria; Cai, Minmin; Straaten, Nontje; Yao, Jun; Richnow, Hans H.; Krüger, Martin

2015-04-01

Microbial transformation of oil to methane is one of the main degradation processes taking place in oil reservoirs, and it has important consequences as it negatively affects the quality and economic value of the oil. Nevertheless, methane could constitute a recovery method of carbon from exhausted reservoirs. Previous studies combining geochemical and isotopic analysis with molecular methods showed evidence for in situ methanogenic oil degradation in the Dagang oil field, China (Jiménez et al., 2012). However, the main key microbial players and the underlying mechanisms are still relatively unknown. In order to better characterize these processes and identify the main microorganisms involved, laboratory biodegradation experiments under methanogenic conditions were performed. Microcosms were inoculated with production and injection waters from the reservoir, and oil or 13C-labelled single hydrocarbons (e.g. n-hexadecane or 2-methylnaphthalene) were added as sole substrates. Indigenous microbiota were able to extensively degrade oil within months, depleting most of the n-alkanes in 200 days, and producing methane at a rate of 76 ± 6 µmol day-1 g-1 oil added. They could also produce heavy methane from 13C-labeled 2-methylnaphthalene, suggesting that further methanogenesis may occur from the aromatic and polyaromatic fractions of Dagang reservoir fluids. Microbial communities from oil and 2-methyl-naphthalene enrichment cultures were slightly different. Although, in both cases Deltaproteobacteria, mainly belonging to Syntrophobacterales (e.g. Syntrophobacter, Smithella or Syntrophus) and Clostridia, mostly Clostridiales, were among the most represented taxa, Gammaproteobacteria could be only identified in oil-degrading cultures. The proportion of Chloroflexi, exclusively belonging to Anaerolineales (e.g. Leptolinea, Bellilinea) was considerably higher in 2-methyl-naphthalene degrading cultures. Archaeal communities consisted almost exclusively of representatives of Methanomicrobia (mainly belonging to genera Methanosaeta and Methanoculleus). As both syntrophic Bacteria and methanogenic Archaea are abundant in Dagang, the studied areas of this oil field may have a significant potential to test the in situ conversion of oil into methane as a possible way to increase total hydrocarbon recovery.

A Case Study Examining Egypt, Nigeria, and Venezuela and their Flaring Behavior Utilizing VIIRS Satellite Data

NASA Astrophysics Data System (ADS)

Englander, J. G.; Austin, A. T.; Brandt, A. R.

2016-12-01

The need to quantify flaring by oil and gas fields is receiving more scrutiny, as there has been scientific and regulatory interest in quantifying the greenhouse gas (GHG) impact of oil and gas production. The National Oceanic and Atmospheric Administration (NOAA) has developed a method to track flaring activity using a Visible Infrared Imaging Radiometer Suite (VIIRS) satellite.[1] This reports data on the average size, power, and light intensity of each flare. However, outside of some small studies, the flaring intensity has generally been estimated at the country level.[2]While informative, country-level assessments cannot provide guidance about the sustainability of particular crude streams or products produced. In this work we generate detailed oil-field-level flaring intensities for a number of global oilfield operations. We do this by merging the VIIRS dataset with global oilfield atlases and other spatial data sources. Joining these datasets together with production data allows us to provide better estimates for the GHG intensity of flaring at the field level for these countries.[3]First, we compute flaring intensities at the field level for 75 global oil fields representing approximately 25% of global production. In addition, we examine in detail three oil producing countries known to have high rates of flaring: Egypt, Nigeria, and Venezuela. For these countries we compute the flaring rate for all fields in the country and explore within-and between-country variation. The countries' fields will be analyzed to determine the correlation of flare activity to a certain field type, crude type, region, or production method. [1] Cao, C. "Visible Infrared Imaging Radiometer Suite (VIIRS)." NOAA NPP VIIRS. NOAA, 2013. Web. 30 July 2016. [2] Elvidge, C. D. et al., "A Fifteen Year Record of Global Natural Gas Flaring Derived from Satellite Data," Energies, vol. 2, no. 3, pp. 595-622, Aug. 2009. [3] World Energy Atlas. 6th ed. London: Petroleum Economist, 2011. Print.

Ettlia oleoabundans growth and oil production on agricultural anaerobic waste effluents.

PubMed

Yang, Ying; Xu, Jianfeng; Vail, Daniel; Weathers, Pamela

2011-04-01

The feasibility of growth and oil production by Ettlia oleoabundans fed with anaerobic digester effluents of three agriculture wastes from the Arkansas Delta, catfish processing waste, soybean field waste, and rice hulls, was studied. Compared to standard BBM medium, all three effluents were deficient in phosphate and nitrate, but rich in ammonia and urea. Best growth was on 2% (v/v) soy effluent, but scant oil was produced on any of the effluents. When the three effluents were mixed, growth did not substantially increase, but oil content increased up to sixfold, depending on age of the effluent. Similar to growth in BBM, the main fatty acids produced were palmitic, oleic, and linoleic. These results show that anaerobically digested agricultural wastes can potentially support both growth and high oil productivity in E. oleoabundans. Copyright © 2011 Elsevier Ltd. All rights reserved.

Depositional environments, sequence stratigraphy, and trapping mechanisms of Fall River Formation in Donkey Creek and Coyote Creek oil fields, Powder River basin, Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knox, P.R.

1989-09-01

Donkey Creek and Coyote Creek fields contain combined reserves of approximately 35 million bbl of oil and are within a trend of fields on the eastern flank of the Powder River basin that totals over 100 million bbl of reserves. The principal producing formation is the Lower Cretaceous Fall River Sandstone. A study of 45 cores and 248 logs from the three pools in the Donkey Creek and Coyote fields has shown that the Fall River is composed of three progradational deltaic units deposited during a period of rising relative sea level. These are locally eroded and are filled bymore » a fluvial point-bar complex deposited following a lowering of relative sea level. Four important depositional facies have been recognized: the delta-front and distributary-channel sandstone of the highstand deltaic sequence and the point-bar sandstone and channel-abandonment of the lowstand fluvial sequence. Stratigraphic traps in Coyote Creek and south Donkey Creek pools are the result of permeable (250 md) point-bar sandstone (250 bbl oil/day ip) bounded updip by impermeable (0.1 md) channel abandonment mudstone. Most of the oil in the central Donkey Creek pool is produced from permeable (76 md) distributary-channel sandstone (150 bbl oil/day ip), which is restricted to the western flank of a structural nose. Lesser production, on the crest and upper western flank of the structure, is obtained from the less permeable (2.8 md) delta-front sandstone (50 bbl oil/day ip). Production is possibly limited to the crest and western flank by hydrodynamic processes.« less

OFC: People, and a drum of know-how. [Oil Field Chemicals division of Exxon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1978-01-01

The Oil Field Chemicals (OFC) division of Exxon Chemical USA story is one more of people than products, more one of selling through experience than selling through persuasion. OFC sales representatives direct teams dedicated to solving problems in the oil field, pipelines, refineries, and petrochemical plants. The major enemy in oil production is water. When a reservoir is first produced the oil is fairly dry. In time, water comes and with it a host of problems: stable emulsions, corrosion that eats at pipes and equipment, scaling, and bacterial growth. This brings into play the know-how of OFC people and theirmore » ability to diagnose the problem and make the right recommendation. If their field evaluations are inconclusive they will call for help from technical specialists in the Chemical Specialties Technology division for specific situations. These specialists travel to the site, run tests, then quickly develop alternatives. Depending on the solution, the Houston Chemical Plant may be called on to manufacture blends in commercial quantities in a remarkably short period of time. How some of these field problems were solved are described.« less

Future oil and gas: Can Iran deliver?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takin, M.

1996-11-01

Iran`s oil and gas production and exports constitute the country`s main source of foreign exchange earnings. The future level of these earnings will depend on oil prices, global demand for Iranian exports, the country`s productive capability and domestic consumption. The size of Iranian oil reserves suggests that, in principle, present productive capacity could be maintained and expanded. However, the greatest share of production in coming years still will come from fields that already have produced for several decades. In spite of significant remaining reserves, these fields are not nearly as prolific as they were in their early years. The operationsmore » required for further development are now more complicated and, in particular, more costly. These fields` size also implies that improving production, and instituting secondary and tertiary recovery methods (such as gas injection), will require mega-scale operations. This article discusses future oil and gas export revenues from the Islamic Republic of Iran, emphasizing the country`s future production and commenting on the effects of proposed US sanctions.« less

On the modeling of the 2010 Gulf of Mexico Oil Spill

NASA Astrophysics Data System (ADS)

Mariano, A. J.; Kourafalou, V. H.; Srinivasan, A.; Kang, H.; Halliwell, G. R.; Ryan, E. H.; Roffer, M.

2011-09-01

Two oil particle trajectory forecasting systems were developed and applied to the 2010 Deepwater Horizon Oil Spill in the Gulf of Mexico. Both systems use ocean current fields from high-resolution numerical ocean circulation model simulations, Lagrangian stochastic models to represent unresolved sub-grid scale variability to advect oil particles, and Monte Carlo-based schemes for representing uncertain biochemical and physical processes. The first system assumes two-dimensional particle motion at the ocean surface, the oil is in one state, and the particle removal is modeled as a Monte Carlo process parameterized by a one number removal rate. Oil particles are seeded using both initial conditions based on observations and particles released at the location of the Maconda well. The initial conditions (ICs) of oil particle location for the two-dimensional surface oil trajectory forecasts are based on a fusing of all available information including satellite-based analyses. The resulting oil map is digitized into a shape file within which a polygon filling software generates longitude and latitude with variable particle density depending on the amount of oil present in the observations for the IC. The more complex system assumes three (light, medium, heavy) states for the oil, each state has a different removal rate in the Monte Carlo process, three-dimensional particle motion, and a particle size-dependent oil mixing model. Simulations from the two-dimensional forecast system produced results that qualitatively agreed with the uncertain "truth" fields. These simulations validated the use of our Monte Carlo scheme for representing oil removal by evaporation and other weathering processes. Eulerian velocity fields for predicting particle motion from data-assimilative models produced better particle trajectory distributions than a free running model with no data assimilation. Monte Carlo simulations of the three-dimensional oil particle trajectory, whose ensembles were generated by perturbing the size of the oil particles and the fraction in a given size range that are released at depth, the two largest unknowns in this problem. 36 realizations of the model were run with only subsurface oil releases. An average of these results yields that after three months, about 25% of the oil remains in the water column and that most of the oil is below 800 m.

Hydrocarbon emissions in the Bakken oil field in North Dakota

NASA Astrophysics Data System (ADS)

Mielke-Maday, I.; Petron, G.; Miller, B.; Frost, G. J.; Peischl, J.; Kort, E. A.; Smith, M. L.; Karion, A.; Dlugokencky, E. J.; Montzka, S. A.; Sweeney, C.; Ryerson, T. B.; Tans, P. P.; Schnell, R. C.

2014-12-01

Within the past five years, the production of oil and natural gas in the United States from tight formations has increased rapidly due to advances in technology, such as horizontal drilling and hydraulic fracturing. With the expansion of oil and natural gas extraction operations comes the need to better quantify their emissions and potential impacts on climate forcing and air quality. The Bakken formation within the Williston Basin in North Dakota has emerged as a large contributor to the recent growth in oil production and accounts for over 10% of domestic production. Close to 30% of associated gas co-produced with the oil is flared. Very little independent information is currently available to assess the oil and gas industry emissions and their impacts on regional air quality. In May 2014, an airborne field campaign was conducted by the National Oceanic and Atmospheric Administration's (NOAA) Earth System Research Laboratory and the University of Michigan to investigate hydrocarbon emissions from operations in the oil field. Here, we present results from the analysis for methane, several non-methane hydrocarbons and combustion tracers in 72 discrete air samples collected by the aircraft on nine different flights. Samples were obtained in the boundary layer upwind and downwind of the operations and in the free troposphere. We will show results of a multiple species analysis and compare them with field campaign data from other U.S. oil and gas fields, measurements from NOAA's Global Monitoring Division long-term observing network, and available bottom-up information on emissions from oil and gas operations.

Geospatial Analysis of Oil and Gas Wells in California

NASA Astrophysics Data System (ADS)

Riqueros, N. S.; Kang, M.; Jackson, R. B.

2015-12-01

California currently ranks third in oil production by U.S. state and more than 200,000 wells have been drilled in the state. Oil and gas wells provide a potential pathway for subsurface migration, leading to groundwater contamination and emissions of methane and other fluids to the atmosphere. Here we compile available public databases on oil and gas wells from the California Department of Conservation's Division of Oil, Gas, and Geothermal Resources, the U.S. Geological Survey, and other state and federal sources. We perform geospatial analysis at the county and field levels to characterize depths, producing formations, spud/completion/abandonment dates, land cover, population, and land ownership of active, idle, buried, abandoned, and plugged wells in California. The compiled database is designed to serve as a quantitative platform for developing field-based groundwater and air emission monitoring plans.

Bridging the Gap between Chemical Flooding and Independent Oil Producers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stan McCool; Tony Walton; Paul Whillhite

2012-03-31

Ten Kanas oil reservoirs/leases were studied through geological and engineering analysis to assess the potential performance of chemical flooding to recover oil. Reservoirs/leases that have been efficiently waterflooded have the highest performance potential for chemical flooding. Laboratory work to identify efficient chemical systems and to test the oil recovery performance of the systems was the major effort of the project. Efficient chemical systems were identified for crude oils from nine of the reservoirs/leases. Oil recovery performance of the identified chemical systems in Berea sandstone rocks showed 90+ % recoveries of waterflood residual oil for seven crude oils. Oil recoveries increasedmore » with the amount of chemical injected. Recoveries were less in Indiana limestone cores. One formulation recovered 80% of the tertiary oil in the limestone rock. Geological studies for nine of the oil reservoirs are presented. Pleasant Prairie, Trembley, Vinland and Stewart Oilfields in Kansas were the most favorable of the studied reservoirs for a pilot chemical flood from geological considerations. Computer simulations of the performance of a laboratory coreflood were used to predict a field application of chemical flooding for the Trembley Oilfield. Estimates of field applications indicated chemical flooding is an economically viable technology for oil recovery.« less

Fate of injected CO2 in the Wilcox Group, Louisiana, Gulf Coast Basin: Chemical and isotopic tracers of microbial–brine–rock–CO2 interactions

USGS Publications Warehouse

Shelton, Jenna L.; McIntosh, Jennifer C.; Warwick, Peter D.; Lee Zhi Yi, Amelia

2014-01-01

The “2800’ sandstone” of the Olla oil field is an oil and gas-producing reservoir in a coal-bearing interval of the Paleocene–Eocene Wilcox Group in north-central Louisiana, USA. In the 1980s, this producing unit was flooded with CO2 in an enhanced oil recovery (EOR) project, leaving ∼30% of the injected CO2 in the 2800’ sandstone post-injection. This study utilizes isotopic and geochemical tracers from co-produced natural gas, oil and brine to determine the fate of the injected CO2, including the possibility of enhanced microbial conversion of CO2 to CH4 via methanogenesis. Stable carbon isotopes of CO2, CH4 and DIC, together with mol% CO2 show that 4 out of 17 wells sampled in the 2800’ sandstone are still producing injected CO2. The dominant fate of the injected CO2appears to be dissolution in formation fluids and gas-phase trapping. There is some isotopic and geochemical evidence for enhanced microbial methanogenesis in 2 samples; however, the CO2 spread unevenly throughout the reservoir, and thus cannot explain the elevated indicators for methanogenesis observed across the entire field. Vertical migration out of the target 2800’ sandstone reservoir is also apparent in 3 samples located stratigraphically above the target sand. Reservoirs comparable to the 2800’ sandstone, located along a 90-km transect, were also sampled to investigate regional trends in gas composition, brine chemistry and microbial activity. Microbial methane, likely sourced from biodegradation of organic substrates within the formation, was found in all oil fields sampled, while indicators of methanogenesis (e.g. high alkalinity, δ13C-CO2 and δ13C-DIC values) and oxidation of propane were greatest in the Olla Field, likely due to its more ideal environmental conditions (i.e. suitable range of pH, temperature, salinity, sulfate and iron concentrations).

Molecular imprinted hydrogel polymer (MIHP) as microbial immobilization media in artificial produced water treatment

NASA Astrophysics Data System (ADS)

Kardena, E.; Ridhati, S. L.; Helmy, Q.

2018-01-01

Produced water generated during oil and gas exploration and drilling, consists of many chemicals which used in drilling process. The production of produced water is over three fold of the oil production. The water-cut has increased over time and continues to do so because the fraction of oil in the reservoir decreases and it is more difficult to get the oil out from an old oil-field. It therefore requires more sea water to be injected in order to force the oil out; hence more produced water is generated. Produced water can pollute the environment if it is not treated properly. In this research, produced water will be treated biologically using bacterial consortium which is isolated from petroleum processing facility with Molecular Imprinted Hydrogel Polymer (MIHP) for microbial immobilization media. Microbial growth rate is determined by measuring the MLVSS and hydrogel mass, also by SEM-EDS analysis. SEM-EDS analysis is an analysis to evidence the presence of microbe trapped in hydrogel, and also to determine the types and weight of the molecules of hydrogel. From this research, suspended microbial growth rate was found at 0.1532/days and attached microbial growth rate was 0.3322/days. Furthermore, based on SEM analysis, microbe is entrapped inside the hydrogel. Effectiveness of microbial degradation activity was determined by measuring organic materials as COD. Based on COD measurement, degradation rate of organic materials in wastewater is 0.3089/days, with maximum COD removal efficiency of 76.67%.

Oil-in-water monitoring using membrane inlet mass spectrometry.

PubMed

Brkić, Boris; France, Neil; Taylor, Stephen

2011-08-15

A membrane inlet mass spectrometry (MIMS) system has been used for detection and analysis of two types of North Sea crude oil. The system was installed on-field on the Flotta Oil Terminal (Orkney, UK). It consisted of a quadrupole mass spectrometer (QMS) connected to the capillary probe with a silicone-based membrane. The produced mass spectra and calibration plots from the MIMS instrument showed the capability to measure levels of individual hydrocarbons within crude oil in seawater. The generated mass spectra from the field tests also showed the ability to distinguish between different types of oil and to determine concentrations of toxic hydrocarbons in oil (e.g., benzene, toluene, and xylene (BTX)). The performance of the instrument at different temperatures of seawater and oil droplet sizes was also investigated. The results showed that the QMS-based MIMS system has a potential to complement existing oil-in-water (OiW) monitors by being able to detect different oil types and specific hydrocarbon concentrations with high accuracy, which are currently not supported in commercially available OiW monitors.

Fate(s) of injected CO2 in a coal-bearing formation, Louisiana, Gulf Coast Basin: Chemical and isotopic tracers of microbial-brine-rock-CO2 interactions

USGS Publications Warehouse

Shelton, Jenna L.

2013-01-01

Coal beds are one of the most promising reservoirs for geologic carbon dioxide (CO₂) sequestration, as CO₂ can strongly adsorb onto organic matter and displace methane; however, little is known about the long-term fate of CO₂ sequestered in coal beds. The "2800' sand" of the Olla oil field is a coal-bearing, oil and gas-producing reservoir of the Paleocene–Eocene Wilcox Group in north-central Louisiana. In the 1980s, this field, specifically the 2800' sand, was flooded with CO₂ in an enhanced oil recovery (EOR) project, with 9.0×10⁷m³ of CO₂ remaining in the 2800' sand after injection ceased. This study utilized isotopic and geochemical tracers from co-produced natural gas, oil and brine from reservoirs located stratigraphically above, below and within the 2800' sand to determine the fate of the remaining EOR-CO₂, examining the possibilities of CO₂ migration, dissolution, mineral trapping, gas-phase trapping, and sorption to coal beds, while also testing a previous hypothesis that EOR-CO₂ may have been converted by microbes (CO₂-reducing methanogens) into methane, creating a microbial "hotspot". Reservoirs stratigraphically-comparable to the 2800' sand, but located in adjacent oil fields across a 90-km transect were sampled to investigate regional trends in gas composition, brine chemistry and microbial activity. The source field for the EOR-CO₂, the Black Lake Field, was also sampled to establish the δ¹³C-CO₂ value of the injected gas (0.9‰ +/- 0.9‰). Four samples collected from the Olla 2800' sand produced CO₂-rich gas with δ¹³C-CO₂ values (average 9.9‰) much lower than average (pre-injection) conditions (+15.9‰, average of sands located stratigraphically below the 2800' sand in the Olla Field) and at much higher CO₂ concentrations (24.9 mole %) than average (7.6 mole %, average of sands located stratigraphically below the 2800' sand in the Olla Field), suggesting the presence of EOR-CO₂ and gas-phase trapping as a major storage mechanism. Using δ¹³C values of CO₂ and dissolved organic carbon (DIC), CO₂ dissolution was also shown to be a major storage mechanism for 3 of the 4 samples from the Olla 2800' sand. Minor storage mechanisms were shown to be migration, which only affected 2 samples (from 1 well), and some EOR-CO₂ conversion to microbial methane for 3 of the 4 Olla 2800' sand samples. Since methanogenesis was not shown to be a major storage mechanism for the EOR-CO₂ in the Olla Field (CO₂ injection did not stimulate methanogenesis), samples were examined from adjacent oil fields to determine the cause of the Olla microbial "hot-spot". Microbial methane was found in all oil fields sampled, but indicators of methanogenesis (e.g. alkalinity, high δ¹³C-DIC values) were the greatest in the Olla Field, and the environmental conditions (salinity, pH, temperature) were most ideal for microbial CO₂ reduction in the Olla field, compared to adjacent fields.

Olive oil pilot-production assisted by pulsed electric field: impact on extraction yield, chemical parameters and sensory properties.

PubMed

Puértolas, Eduardo; Martínez de Marañón, Iñigo

2015-01-15

The impact of the use of pulsed electric field (PEF) technology on Arroniz olive oil production in terms of extraction yield and chemical and sensory quality has been studied at pilot scale in an industrial oil mill. The application of a PEF treatment (2 kV/cm; 11.25 kJ/kg) to the olive paste significantly increased the extraction yield by 13.3%, with respect to a control. Furthermore, olive oil obtained by PEF showed total phenolic content, total phytosterols and total tocopherols significantly higher than control (11.5%, 9.9% and 15.0%, respectively). The use of PEF had no negative effects on general chemical and sensory characteristics of the olive oil, maintaining the highest quality according to EU legal standards (EVOO; extra virgin olive oil). Therefore, PEF could be an appropriate technology to improve olive oil yield and produce EVOO enriched in human-health-related compounds, such as polyphenols, phytosterols and tocopherols. Copyright © 2014 Elsevier Ltd. All rights reserved.

Laboratory and field evaluation of neem (Azadirachta indica A. Juss) and Chinaberry (Melia azedarach L.) oils as repellents against Phlebotomus orientalis and P. bergeroti (Diptera: Psychodidae) in Ethiopia.

PubMed

Kebede, Yosef; Gebre-Michael, Teshome; Balkew, Meshesha

2010-02-01

The study evaluated the efficacy of neem (Azadirachta indica A. Juss.) and Chinaberry (Melia azedarach L.) seed oils as repellents against laboratory and field populations of some sandflies in Ethiopia. In the laboratory, concentrations of 2% and 5% neem oil in coconut oil tested against Phlebotomus orientalis (vector of visceral leishmaniasis) provided 96.28% (95% CI=95.60-96.97) protection up to a mean time of 7h and 20 min and 98.26% (95% CI=93.46-104. 07) protection up to 9h, respectively. Similarly, M. azedarach oil at 2% concentration produced 95.13% (95% CI=90.74-99.52) protection for the same duration (7h and 20 min), while the 5% oil gave 96.20 (95% CI=86.98-105.41) protection for 8h and 20 min against the same species with no significant difference in percentage protection between the two oils at 2% and 5% concentrations. In the field tests with only neem oil (A. indica) against field populations of P. orientalis and P. bergeroti, similar high level of repellencies were recorded with about the same duration of protection. Application of both neem and Chinaberry oils can be safe and low-cost means of personal protection against sandfly bites in endemic areas of Ethiopia, if the community is advised and encouraged to grow the plants abundantly. Copyright 2009 Elsevier B.V. All rights reserved.

Records of wells drilled for oil and gas in Montana, June 1, 1951 through December 31, 1953

USGS Publications Warehouse

Smith, Howard R.

1955-01-01

Data concerning about 1, 800 dry holes and selected producing wells drilled in Montana from June 1, 1951, through December 31, 1953, are contained in this circular, which supplements Circular 172 published in 1952. Also included is a table listing the oil and gas fields of Montana. WELLS DRILLED FOR OIL AND GAS IN MONTANA FROM JUNE 1, 1951, THOROUGH DECEMBER 31, 1953 This circular contains data on dry holes and selected producing wells drilled in Montana from June 1, 1951, through December 31, 1953, and supplements Circular 172 published in 1952 showing records of wells drilled prior to June 1, 1951. Table 1 lists the oil and gas fields of Montana (see map OM 130). The list of wells in table 2 has been compiled from information in Geological Survey files and includes most if not all the unsuccessful wildcat test wells and unsuccessful field extension wells drilled from June 1, 1951 to December 31, 1953. It also includes some older but successful field extension wells that had not been listed in Circular 172. Data are tabulated under location, county, field or geologic structure, operator, lease, and well number, elevation, geologic formation (at the surface and lowest formation reached), production or shows of oil or gas, total depth, and status and date. The wells are tabulated by township, range, quarter, and section in the order of townships north-ranges west, townships north-ranges east, townships south-ranges east, and townships south-ranges west. The names entered under 'Field or geologic structure' are those of the productive area or the geologic structure on or near which the wells have been drilled. Ground elevations have been given for wells for which the records indicated the reference point of the elevation. The surface formation and lowest formation reached in the wells are indicated by symbols which are identified on the accompanying explanation of formation symbols (fig. 1). Not all of the nomenclature is in accord with current Geological Survey usage. In the column 'Production or shows of oil and gas' the symbol GS is used for gas shows, OS for oil shows, GOS for shows of both gas and oil, GP for gas production, and OP for oil production. A number following the symbol for a show or production indicates the depth to the top of the zone in which the gas or oil was found. The letter symbol following the number or the hyphen indicates the geologic formation in which the gas or oil occurs. The status and depth of each well is indicated. The letters A, C, and D preceding the date indicate abandoned, completed, or drilling, respectively, in the specified year. Most if not all producing wells that have been abandoned are shown as completed wells. The date of abandonment is the year in which drilling ceased, except for a few wells in which the abandonment was preceded by one or more years of suspended operations. The diagrammatic representation of the succession of geologic formations in Montana (fig. 1) provides identification of the letter symbols used in the tabulation to indicate geologic formations.

Classification of crude oils produced by in situ combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ryabov, V.D.; Dauda, S.; Tabasaranskaya, T.Z.

1995-05-01

It was shown in that oil from the Karazhanbas field undergoes thermal and thermooxidative conversions in the course of production by in situ combustion (ISC). It has been proposed that crudes produced by this method should be assigned to three classes - those that have been subjected to thermal action only, those that have been subjected to thermooxidative action, and unconverted (native) crudes. This sort of classification is necessary in resolving questions of logical mixing of crudes, transportation, storage, and subsequent processing.

Libya, Algeria and Egypt: crude oil potential from known deposits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dietzman, W.D.; Rafidi, N.R.; Ross, T.A.

1982-04-01

An analysis is presented of the discovered crude oil resources, reserves, and estimated annual production from known fields of the Republics of Libya, Algeria, and Egypt. Proved reserves are defined as the remaining producible oil as of a specified date under operating practice in effect at that time and include estimated recoverable oil in undrilled portions of a given structure or structures. Also included in the proved reserve category are the estimated indicated additional volumes of recoverable oil from the entire oil reservoir where fluid injection programs have been started in a portion, or portions, of the reservoir. The indicatedmore » additional reserves (probable reserves) reported herein are the volumes of crude oil that might be obtained with the installation of secondary recovery or pressure maintenance operations in reservoirs where none have been previously installed. The sum of cumulative production, proved reserves, and probable reserves is defined as the ultimate oil recovery from known deposits; and resources are defined as the original oil in place (OOIP). An assessment was made of the availability of crude oil under three assumed sustained production rates for each country; an assessment was also made of each country's capability of sustaining production at, or near, the 1980 rates assuming different limiting reserve to production ratios. Also included is an estimate of the potential maximum producing capability from known deposits that might be obtained from known accumulations under certain assumptions, using a simple time series approach. The theoretical maximum oil production capability from known fields at any time is the maximum deliverability rate assuming there are no equipment, investment, market, or political constraints.« less

Constructive Activation of Reservoir-Resident Microbes for Enhanced Oil Recovery

NASA Astrophysics Data System (ADS)

DeBruyn, R. P.

2017-12-01

Microbial communities living in subsurface oil reservoirs biodegrade oil, producing methane. If this process could create methane within the waterflooded pore spaces of an oilfield, the methane would be expected to remain and occupy pore space, decreasing water relative permeability, diverting water flow, and increasing oil recovery by expanding the swept zone of the waterflood. This approach was tested in an oilfield in northern Montana. Preliminary assessments were made of geochemical conditions and microbiological habitations. Then, a formulation of microbial activators, with composition tailored for the reservoir's conditions, was metered at low rates into the existing injection water system for one year. In the field, the responses observed included improved oil production performance; a slight increase in injection pressure; and increased time needed for tracers to move between injection and producing wells. We interpret these results to confirm that successful stimulation of the microbial community caused more methane to be created within the swept zone of the waterflooded reservoir. When the methane exsolved as water flowed between high-pressure injection and low-pressure production wells, the bubbles occupied pore space, reducing water saturation and relative permeability, and re-directing some water flow to "slower" unswept rock with lower permeability and higher oil saturation. In total, the waterflood's swept zone had been expanded to include previously-unflooded rock. This technology was applied in this field after screening based on careful anaerobic sampling, advanced microbiological analysis, and the ongoing success of its waterflood. No reservoir or geological or geophysical simulation models were employed, and physical modifications to field facilities were minor. This technology of utilizing existing microbial populations for enhanced oil recovery can therefore be considered for deployment into waterfloods where small scale, advanced maturity, or insufficiency of data make other technologies too expensive.

Patrick Draw field, Wyoming - 1 seismic expression of subtle strat trap in Upper Cretaceous Almond

USGS Publications Warehouse

Ryder, Robert T.; Lee, Myung W.; Agena, Warren F.; Anderson, Robert C.

1990-01-01

The east flank of the Rock Springs uplift and the adjacent Wamsutter arch contain several large hydrocarbon accumulations. Among these accumulations are Patrick Draw field, which produces oil and gas from a stratigraphic trap in the Upper Cretaceous Almond formation, and Table Rock field, a faulted anticlinal trap that produces gas from multiple Tertiary, Mesozoic, and Paleozoic reservoirs. The principal petroleum reservoir in Patrick Draw field is a sandstone at the top of the Almond formation. This sandstone attains a maximum thickness of 35ft and piches out westward into relatively impervious silt-stone and shale that constitute the trapping facies. The objective of this investigation is to determine whether or not the stratigraphic trap at Patrick Draw can be detected on a 12 fold, common depth point seismic profile acquired by Forest Oil Corp. and its partners. The seismic line is 18.5 miles long and crosses Patrick Draw and Table Rock fields.

PAH body burden and biomarker responses in mussels (Mytilus edulis) exposed to produced water from a North Sea oil field: laboratory and field assessments.

PubMed

Sundt, Rolf C; Pampanin, Daniela M; Grung, Merete; Baršienė, Janina; Ruus, Anders

2011-07-01

In order to study the impact of produced water (PW) from a North Sea oil field on blue mussels (Mytilus edulis), chemical and biological markers were selected. A laboratory exposure (0.125%, 0.25% and 0.5% of PW) and a field study (6 stations 0.2-2 km from a PW discharge point) were conducted. In the laboratory study, PAH bioaccumulation increased in mussel soft tissue even at the lowest exposure dose. Micronuclei frequency demonstrated a dose-response pattern, whereas lysosomal membrane stability showed tendency towards a dose-response pattern. The same markers were assessed in the field study, biomarker analyses were consistent with the contamination level, as evaluated by mussel polycyclic aromatic hydrocarbons body burden. Overall, obtained results confirmed the value of an ecotoxicological approach for a scientifically sound characterisation of biological effects induced by offshore oilfield operational discharges. Copyright © 2011 Elsevier Ltd. All rights reserved.

The influence on response of axial rotation of a six-group local-conductance probe in horizontal oil-water two-phase flow

NASA Astrophysics Data System (ADS)

Weihang, Kong; Lingfu, Kong; Lei, Li; Xingbin, Liu; Tao, Cui

2017-06-01

Water volume fraction is an important parameter of two-phase flow measurement, and it is an urgent task for accurate measurement in horizontal oil field development and optimization of oil production. The previous ring-shaped conductance water-cut meter cannot obtain the response values corresponding to the oil field water conductivity for oil-water two-phase flow in horizontal oil-producing wells characterized by low yield liquid, low velocity and high water cut. Hence, an inserted axisymmetric array structure sensor, i.e. a six-group local-conductance probe (SGLCP), is proposed in this paper. Firstly, the electric field distributions generated by the exciting electrodes of SGLCP are investigated by the finite element method (FEM), and the spatial sensitivity distributions of SGLCP are analyzed from the aspect of different separations between two electrodes and different axial rotation angles respectively. Secondly, the numerical simulation responses of SGLCP in horizontal segregated flow are calculated from the aspect of different water cut and heights of the water layer, respectively. Lastly, an SGLCP-based well logging instrument was developed, and experiments were carried out in a horizontal pipe with an inner diameter of 125 mm on the industrial-scale experimental multiphase flow setup in the Daqing Oilfield, China. In the experiments, the different oil-water two-phase flow, mineralization degree, temperature and pressure were tested. The results obtained from the simulation experiments and simulation well experiments demonstrate that the designed and developed SGLCP-based instrument still has a good response characteristic for measuring water conductivity under the different conditions mentioned above. The validity and reliability of obtaining the response values corresponding to the water conductivity through the designed and developed SGLCP-based instrument are verified by the experimental results. The significance of this work can provide an effective technology for measuring the water volume fraction of oil-water two-phase flow in horizontal oil-producing wells.

New exploration targets in Malaysia: Deep sandstone reservoirs in Malay basin and turbidites in Sabah basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ngah, K.B.

1996-12-31

Much of the production in Malaysia is from middle to upper Miocene sandstones and carbonates in three main basins: Malay, Sarawak (Its three subbasins-Central Luconia, Balingian and Baram), and Sabah. Fifteen fields produce an average of 630,000 bopd and 3.0 bcfgpd. More than 4.0 billion barrels of oil and 20 tcf of gas have been produced, and reserves are 4.2 billion barrels of oil and 90 tcf. Oil production will decline within the next 1 0 years unless new discoveries are made and/or improved oil recovery methods introduced, but gas production of 5 tcf, expected after the turn of themore » century, can be sustained for several decades. Successful exploratory wells continue to be drilled in the Malaysian Tertiary basins, and others are anticipated with application of new ideas and technology. In the Malay basin, Miocene sandstone reservoirs in Groups L and M have been considered as very {open_quote}high risk{close_quotes} targets, the quality of the reservoirs has generally been thought to be poor, especially toward the basinal center, where they occur at greater depth. The cause of porosity loss is primarily burial-related. Because of this factor and overpressuring, drilling of many exploration wells has been suspended at or near the top of Group L. In a recent prospect drilled near the basinal axis on the basis of advanced seismic technology, Groups L and M sandstones show fair porosity (8-15%) and contain gas. In the Sabah basin, turbidite play has received little attention, partly because of generally poor seismic resolution in a very complex structural setting. Only one field is known to produce oil from middle Miocene turbidities. However, using recently acquired 3-D seismic data over this field, new oil pools have been discovered, and they are currently being developed. These finds have created new interest, as has Shell`s recent major gas discovery from a turbidite play in this basin.« less

New exploration targets in Malaysia: Deep sandstone reservoirs in Malay basin and turbidites in Sabah basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ngah, K.B.

1996-01-01

Much of the production in Malaysia is from middle to upper Miocene sandstones and carbonates in three main basins: Malay, Sarawak (Its three subbasins-Central Luconia, Balingian and Baram), and Sabah. Fifteen fields produce an average of 630,000 bopd and 3.0 bcfgpd. More than 4.0 billion barrels of oil and 20 tcf of gas have been produced, and reserves are 4.2 billion barrels of oil and 90 tcf. Oil production will decline within the next 1 0 years unless new discoveries are made and/or improved oil recovery methods introduced, but gas production of 5 tcf, expected after the turn of themore » century, can be sustained for several decades. Successful exploratory wells continue to be drilled in the Malaysian Tertiary basins, and others are anticipated with application of new ideas and technology. In the Malay basin, Miocene sandstone reservoirs in Groups L and M have been considered as very [open quote]high risk[close quotes] targets, the quality of the reservoirs has generally been thought to be poor, especially toward the basinal center, where they occur at greater depth. The cause of porosity loss is primarily burial-related. Because of this factor and overpressuring, drilling of many exploration wells has been suspended at or near the top of Group L. In a recent prospect drilled near the basinal axis on the basis of advanced seismic technology, Groups L and M sandstones show fair porosity (8-15%) and contain gas. In the Sabah basin, turbidite play has received little attention, partly because of generally poor seismic resolution in a very complex structural setting. Only one field is known to produce oil from middle Miocene turbidities. However, using recently acquired 3-D seismic data over this field, new oil pools have been discovered, and they are currently being developed. These finds have created new interest, as has Shell's recent major gas discovery from a turbidite play in this basin.« less

Coreflood assay using extremophile microorganisms for recovery of heavy oil in Mexican oil fields.

PubMed

Castorena-Cortés, Gladys; Roldán-Carrillo, Teresa; Reyes-Avila, Jesús; Zapata-Peñasco, Icoquih; Mayol-Castillo, Martha; Olguín-Lora, Patricia

2012-10-01

A considerable portion of oil reserves in Mexico corresponds to heavy oils. This feature makes it more difficult to recover the remaining oil in the reservoir after extraction with conventional techniques. Microbial enhanced oil recovery (MEOR) has been considered as a promising technique to further increase oil recovery, but its application has been developed mainly with light oils; therefore, more research is required for heavy oil. In this study, the recovery of Mexican heavy oil (11.1°API and viscosity 32,906 mPa s) in a coreflood experiment was evaluated using the extremophile mixed culture A7, which was isolated from a Mexican oil field. Culture A7 includes fermentative, thermophilic, and anaerobic microorganisms. The experiments included waterflooding and MEOR stages, and were carried out under reservoir conditions (70°C and 9.65 MPa). MEOR consisted of injections of nutrients and microorganisms followed by confinement periods. In the MEOR stages, the mixed culture A7 produced surface-active agents (surface tension reduction 27 mN m⁻¹), solvents (ethanol, 1738 mg L⁻¹), acids (693 mg L⁻¹), and gases, and also degraded heavy hydrocarbon fractions in an extreme environment. The interactions of these metabolites with the oil, as well as the bioconversion of heavy oil fractions to lighter fractions (increased alkanes in the C₈-C₃₀ range), were the mechanisms responsible for the mobility and recovery of heavy oil from the porous media. Oil recovery by MEOR was 19.48% of the residual oil in the core after waterflooding. These results show that MEOR is a potential alternative to heavy oil recovery in Mexican oil fields. Copyright © 2012 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

INCREASING HEAVY OIL RESERVES IN THE WILMINGTON OIL FIELD THROUGH ADVANCED RESERVOIR CHARACTERIZATION AND THERMAL PRODUCTION TECHNOLOGIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott Hara

2001-06-27

The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California through the testing and application of advanced reservoir characterization and thermal production technologies. The successful application of these technologies will result in expanding their implementation throughout the Wilmington Field and, through technology transfer, to other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block II-A (Tar II-A) has been relatively inefficient because of several producibility problems which are common in SBC reservoirs: inadequate characterization of the heterogeneous turbidite sands,more » high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. A suite of advanced reservoir characterization and thermal production technologies are being applied during the project to improve oil recovery and reduce operating costs.« less

Black shale source rocks and oil generation in the Cambrian and Ordovician of the central Appalachian Basin, USA

USGS Publications Warehouse

Ryder, R.T.; Burruss, R.C.; Hatch, J.R.

1998-01-01

Nearly 600 million bbl of oil (MMBO) and 1 to 1.5 trillion ft3 (tcf) of gas have been produced from Cambrian and Ordovician reservoirs (carbonate and sandstone) in the Ohio part of the Appalachian basin and on adjoining arches in Ohio, Indiana, and Ontario, Canada. Most of the oil and gas is concentrated in the giant Lima-Indiana field on the Findlay and Kankakee arches and in small fields distributed along the Knox unconformity. Based on new geochemical analyses of oils, potential source rocks, bitumen extracts, and previously published geochemical data, we conclude that the oils in both groups of fields originated from Middle and Upper Ordovician blcak shale (Utica and Antes shales) in the Appalachian basin. Moroever, we suggest that approximately 300 MMBO and many trillions of cubic feet of gas in the Lower Silurian Clinton sands of eastern Ohio originated in the same source rocks. Oils from the Cambrian and Ordovician reservoirs have similar saturated hydrocarbon compositions, biomarker distributions, and carbon isotope signatures. Regional variations in the oils are attributed to differences in thermal maturation rather than to differences in source. Total organic carbon content, genetic potential, regional extent, and bitument extract geochemistry identify the balck shale of the Utica and Antes shales as the most plausible source of the oils. Other Cambrian and Ordovician shale and carbonate units, such as the Wells Creek formation, which rests on the Knox unconformity, and the Rome Formation and Conasauga Group in the Rome trough, are considered to be only local petroleum sources. Tmax, CAI, and pyrolysis yields from drill-hole cuttings and core indicate that the Utica Shale in eastern and central Ohio is mature with respect to oil generation. Burial, thermal, and hydrocarbon-generation history models suggest that much of the oil was generated from the Utica-Antes source in the late Paleozoic during the Alleghanian orogeny. A pervasive fracture network controlled by basement tectonics aided in the distribution of oil from the source to the trap. This fracture network permitted oil to move laterally and stratigraphically downsection through eastward-dipping, impermeable carbonate sequences to carrier zones such as the Middle Ordovician Knox unconformity, and to reservoirs such as porous dolomite in the Middle Ordovician Trenton Limestone in the Lima-Indiana field. Some of the oil and gas from the Utica-Antes source escaped vertically through a partially fractured, leaky Upper Ordovician shale seal into widespread Lower Silurian sandstone reservoirs.Nearly 600 million bbl of oil (MMBO) and 1 to 1.5 trillion ft3 (tcf) of gas have been produced from Cambrian and Ordovician reservoirs (carbonate and sandstone) in the Ohio part of the Appalachian basin and on adjoining arches in Ohio, Indiana, and Ontario, Canada. Most of the oil and gas is concentrated in the giant Lima-Indiana field on the Findlay and Kankakee arches and in small fields distributed along the Knox unconformity. Based on new geochemical analyses of oils, potential source rocks, bitumen extracts, and previously published geochemical data, we conclude that the oils in both groups of fields originated from Middle and Upper Ordovician black shale (Utica and Antes shales) in the Appalachian basin. Moreover, we suggest that approximately 300 MMBO and many trillions of cubic feet of gas in the Lower Silurian Clinton sands of eastern Ohio originated in these same source rocks.

China Report Economic Affairs Energy: Status and Development 38.

DTIC Science & Technology

1985-04-29

Measures To Convert From Oil to Coal Showing Results (Li Renjun; NENG YUAN [JOURNAL OF ENERGY] No 6, 25 Dec 84).... • ••• 61 Briefs 67 New Hebei...Coal Mine ’" Liaoning Local Colliery Growth ’ OIL AND GAS More Onshore Oil and Gas Reserves Verified CXINHUA, 12 Apr 85)......... •. • • bb New...Well Gushes Oil in South China Sea CXINHUA, 12 Apr 85) • • • ■ * • • by Daqing Fields Produce 52.3 Million Tons in 1984 _ CMa Zhiping; CHINA

Field experiences with rotordynamic instability in high-performance turbomachinery. [oil and natural gas recovery

NASA Technical Reports Server (NTRS)

Doyle, H. E.

1980-01-01

Two field situations illustrate the consequences of rotordynamic instability in centrifugal compressors. One involves the reinjection of produced gas into a North Sea oil formation for the temporary extraction of crude. The other describes on-shore compressors used to deliver natural gas from off-shore wells. The problems which developed and the remedies attempted in each case are discussed. Instability problems resulted in lost production, extended construction periods and costs, and heavy maintenance expenditures. The need for effective methods to properly identify the problem in the field and in the compressor design stage is emphasized.

Emerald oil field on production in North Sea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-08-31

This paper reports that Midland and Scottish Energy Ltd. (MSE) has placed Emerald oil field on stream in the U.K. North Sea with a floating production unit. Initial production, from two satellite wells, will be used to commission facilities. Three water injection wells have been unplugged and are ready for start-up. MSE will place a central cluster of wells-five producers and one water injector-on stream during the next few weeks. Production will build to an expected 25,000 b/d from 35 million bbl of reserves. Field development has undergone an unusually large number of setbacks and changes.

Earth Observations taken by the Expedition 13 crew

NASA Image and Video Library

2006-05-25

ISS013-E-26488 (25 May 2006) --- Yates Oilfield, west Texas is featured in this image photographed by an Expedition 13 crewmember on the International Space Station. The Permian Basin of west Texas and southeastern New Mexico is one of the most productive petroleum provinces of North America. The Basin is a large depression in the Precambrian bedrock surface along the southern edge of the North American craton, or oldest bedrock core of the continent. The Yates Oil Field is marked in this image by numerous white well locations and petroleum infrastructure dotting the layered sedimentary rocks of the Permian Basin. The Pecos River bed borders the oil field to the east-northeast. The Yates Field started petroleum production in 1926, and by 1995 had produced over 2 billion barrels of oil.

Carbon balance of CO2-EOR for NCNO classification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nunez-Lopez, Vanessa; Gil-Egui, Ramon; Gonzalez-Nicolas, Ana

The question of whether carbon dioxide enhanced oil recovery (CO2-EOR) constitutes a valid alternative for greenhouse gas emission reduction has been frequently asked by the general public and environmental sectors. Through this technology, operational since 1972, oil production is enhanced by injecting CO2 into depleted oil reservoirs in order displace the residual oil toward production wells in a solvent/miscible process. For decades, the CO2 utilized for EOR has been most commonly sourced from natural CO2 accumulations. More recently, a few projects have emerged where anthropogenic CO2 (A-CO2) is captured at an industrial facility, transported to a depleted oil field, andmore » utilized for EOR. If carbon geologic storage is one of the project objectives, all the CO2 injected into the oil field for EOR could technically be stored in the formation. Even though the CO2 is being prevented from entering the atmosphere, and permanently stored away in a secured geologic formation, a question arises as to whether the total CO2 volumes stored in order to produce the incremental oil through EOR are larger than the CO2 emitted throughout the entire CO2-EOR process, including the capture facility, the EOR site, and the refining and burning of the end product. We intend to answer some of these questions through a DOE-NETL funded study titled “Carbon Life Cycle Analysis of CO2-EOR for Net Carbon Negative Oil (NCNO) Classification”. NCNO is defined as oil whose carbon emissions to the atmosphere, when burned or otherwise used, are less than the amount of carbon permanently stored in the reservoir in order to produce the oil. In this paper, we focus on the EOR site in what is referred to as a gate-to-gate system, but are inclusive of the burning of the refined product, as this end member is explicitly stated in the definition of NCNO. Finally, we use Cranfield, Mississippi, as a case study and come to the conclusion that the incremental oil produced is net carbon negative.« less

Mathematical Modeling of Multiphase Filtration in Porous Media with a Chemically Active Skeleton

NASA Astrophysics Data System (ADS)

Khramchenkov, M. G.; Khramchenkov, É. M.

2018-01-01

The authors propose a mathematical model of two-phase filtration that occurs under the conditions of dissolution of a porous medium. The model can be used for joint description of complex chemical-hydrogeomechanical processes that are of frequent occurrence in the oil-and-gas producing and nature conservation practice. As an example, consideration is given to the acidizing of the bottom zone of the injection well of an oil reservoir. Enclosing rocks are represented by carbonates. The phases of the process are an aqueous solution of hydrochloric acid and oil. A software product for computational experiments is developed. For the numerical experiments, use is made of the data on the wells of an actual oil field. Good agreement is obtained between the field data and the calculated data. Numerical experiments with different configurations of the permeability of an oil stratum are conducted.

Letter from Europe: oil business expands; drills go deeper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jenkins, N.

A view of the energy picture as seen from England indicates a great deal of drilling activity is taking place in the North Sea, where 65 platform rigs are producing enough oil to have reduced England's costs for imported oil. Promising new fields southeast and west of the Shetland Islands have not slowed British efforts to keep reserve levels ahead of depletion rates. The Italians are working at depths of up to 1100 meters to extend their gas fields in the Adriatic and Ionian waters. Australia is undertaking a major oil exploration effort in the west and northwest, with competingmore » efforts of several oil companies. The uranium market is complicated by environmental problems, although Canada may export some to Germany and England on a trial basis. Delegates to the London Local Energy Center Conference felt that the United Kingdom needs a total energy policy. The electricity industry opposes this view. (DCK)« less

Report of the Task Group on Independent Research and Development

DTIC Science & Technology

1967-02-01

in 1959 when the technology used in prospecting for oil by seismic means was employed to detect and sug- gest the source of earth shocks generated by...result of TI’ s work in seismology for oil exploration. The use of seismometers for intrusion detection stemmed from the large, unde- sirable signals...produced by any human movement during oil -field seismic tests. The first military contract for six test models of these devices was received in 1963

78 FR 31635 - Oil and Gas; Hydraulic Fracturing on Federal and Indian Lands

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-24

... part of a field development proposal, and whenever there is evidence of a problem with the cement job... of the country that previously did not produce significant amounts of oil or gas. The resulting... received as a result of this revised proposed rule. The BLM's revised proposed rule is generally consistent...

40 CFR 147.1952 - Aquifer exemptions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... accordance with §§ 144.7(b) and 146.4 of this chapter at the time of program promulgation. EPA may in the... II enhanced recovery injection activities only. (1) The Sugar Run and Bradford series of oil... Bradford series of oil producing sands of the Lewis Run Field in McKean County. (4) The Bradford series of...

A resource evaluation of the Bakken Formation (Upper Devonian and Lower Mississippian) continuous oil accumulation, Williston Basin, North Dakota and Montana

USGS Publications Warehouse

Schmoker, J.W.

1996-01-01

The Upper Devonian and Lower Mississippian Bakken Formation in the United States portion of the Williston Basin is both the source and the reservoir for a continuous oil accumulation - in effect a single very large field - underlying approximately 17,800 mi2 (46,100 km2) of North Dakota and Montana. Within this area, the Bakken Formation continuous oil accumulation is not significantly influenced by the water column and cannot be analyzed in terms of conventional, discrete fields. Rather, the continuous accumulation can be envisioned as a collection of oil-charged cells, virtually all of which are capable of producing some oil, but which vary significantly in their production characteristics. Better wellperformance statistics are linked regionally to higher levels of thermal maturity and to lower levels of reservoir heterogeneity. Although portions of the Bakken Formation continuous oil accumulation have reached a mature stage of development, the accumulation as a whole is far from depleted.

Maximize Liquid Oil Production from Shale Oil and Gas Condensate Reservoirs by Cyclic Gas Injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheng, James; Li, Lei; Yu, Yang

The current technology to produce shale oil reservoirs is the primary depletion using fractured wells (generally horizontal wells). The oil recovery is less than 10%. The prize to enhance oil recovery (EOR) is big. Based on our earlier simulation study, huff-n-puff gas injection has the highest EOR potential. This project was to explore the potential extensively and from broader aspects. The huff-n-puff gas injection was compared with gas flooding, water huff-n-puff and waterflooding. The potential to mitigate liquid blockage was also studied and the gas huff-n-puff method was compared with other solvent methods. Field pilot tests were initiated but terminatedmore » owing to the low oil price and the operator’s budget cut. To meet the original project objectives, efforts were made to review existing and relevant field projects in shale and tight reservoirs. The fundamental flow in nanopores was also studied.« less

Petroleum geochemistry of oil and gas from Barbados: Implications for distribution of Cretaceous source rocks and regional petroleum prospectivity

USGS Publications Warehouse

Hill, R.J.; Schenk, C.J.

2005-01-01

Petroleum produced from the Barbados accretionary prism (at Woodbourne Field on Barbados) is interpreted as generated from Cretaceous marine shale deposited under normal salinity and dysoxic conditions rather than from a Tertiary source rock as previously proposed. Barbados oils correlate with some oils from eastern Venezuela and Trinidad that are positively correlated to extracts from Upper Cretaceous La Luna-like source rocks. Three distinct groups of Barbados oils are recognized based on thermal maturity, suggesting petroleum generation occurred at multiple levels within the Barbados accretionary prism. Biodegradation is the most significant process affecting Barbados oils resulting in increased sulfur content and decreased API gravity. Barbados gases are interpreted as thermogenic, having been co-generated with oil, and show mixing with biogenic gas is limited. Gas biodegradation occurred in two samples collected from shallow reservoirs at the Woodbourne Field. The presence of Cretaceous source rocks within the Barbados accretionary prism suggests that greater petroleum potential exists regionally, and perhaps further southeast along the passive margin of South America. Likewise, confirmation of a Cretaceous source rock indicates petroleum potential exists within the Barbados accretionary prism in reservoirs that are deeper than those from Woodbourne Field.

Development of a Geologic Exploration Model foe the Permo-Pennsylvanian Petroleum System in South-Central Montana

DOE Office of Scientific and Technical Information (OSTI.GOV)

David A. Lopez

2007-06-30

Eolian sands are the main Pennsylvanian Tensleep Sandstone reservoir rocks, and were deposited in a near-shore environment interbedded with near-shore marine and sabkha calcareous and dolomitic rocks. Within the Tensleep, numerous cycles are characterized by basal marine or sabkha calcareous sandstone or dolomitic sandstone overlain by porous and permeable eolian sandstone, which in turn is capped by marine sandstone. The cycles represent the interplay of near-shore marine, sabkha, and eolian environments. On the west side of the project area, both the lower and upper Tensleep are present and the total thickness reaches a maximum of about 240 ft. The lowermore » Tensleep is 100 to 120 ft thick and consists of a sequence of repeating cycles of limey shallow marine sandstone, sandy limestone, and sandy dolomite. The upper Tensleep is generally characterized by cycles of sandy limestone or dolomite, overlain by light-colored, eolian dune sandstone capped by marine limey sandstone. In the central and eastern parts of the project area, only the lower Tensleep is present, but here eolian sandstones are in cycles much like those in the west in the upper Tensleep. The lower Tensleep is quite variable in thickness, ranging from about 25 ft to over 200 ft. Oil accumulations in the Tensleep are best described as structurally modified paleostratigraphic accumulations. At Frannie Field, the irregular oil column can be explained by a post-Tensleep channel scour on the west flank of the anticline. On the Powder River Basin side of the project area, the Soap Creek and Lodge Grass Fields produce from the Permo-Pennsylvanian system. In these two fields, erosional remnants of eolian sandstone control the production, similar to the situation at Frannie Field. At Soap Creek the trap is enhanced by structural closure. In the Lodge Grass area, Tensleep oil is trapped in preserved dunes in the footwall of a Laramide reverse fault. Oil generation and migration was early. Two hypotheses have been presented: migration occurred (1) before mid-Jurassic erosion produced a major regional unconformity or (2) about 82 million years ago. Migration pre-Laramide occurred because oil in both the Bighorn Basin and the Powder River Basin are part of the same petroleum system. Geochemical analyses of oils from producing fields across the region show the oils are all similar and have the same source and generation history. No Phosphoria source rocks exist in the project area of south-central Montana, requiring that oil migrated from distant source areas, probably in central and southwestern Wyoming. Oil shows and production in the Tensleep are absent in the northern part of the project area. This appears to be controlled by the merging of the top of the Tensleep Sandstone and the Jurassic unconformity (top of the Triassic Chugwater Formation). There should be potential for the discovery of oil in Tensleep stratigraphic traps or combination traps everywhere south of the Jurassic-Pennsylvanian Isopach zero contour except where the Tensleep has been exposed by uplift and erosion. Known Tensleep fields in south-central Montana are generally small in area, which agrees with outcrop studies that show eolian dune sequences are generally quite small in lateral extent, on the order of 10 to 40 acres. Although existing fields are small in area, they are very productive; individual wells will probably make 300,000 to 500,000 barrels of oil. In the project area, hydrodynamic considerations are important. All the existing Tensleep fields have active water drives. In many cases, the reservoir pressure today is as it was when initially discovered. In areas of high structural complexity, such as the Lodge Grass-Crow Agency fault and the Lake Basin fault zone, significant structural closure may be necessary to trap oil because of the strong hydrodynamic influence exerted by the underlying Madison Formation aquifer.« less

New boundary conditions for oil reservoirs with fracture

NASA Astrophysics Data System (ADS)

Andriyanova, Elena; Astafev, Vladimir

2017-06-01

Based on the fact that most of oil fields are on the late stage of field development, it becomes necessary to produce hard-to-extract oil, which can be obtained only by use of enhance oil recovery methods. For example many low permeable or shale formations can be developed only with application of massive hydraulic fracturing technique. In addition, modern geophysical researches show that mostly oil bearing formations are complicated with tectonic faults of different shape and permeability. These discontinuities exert essential influence on the field development process and on the well performance. For the modeling of fluid flow in the reservoir with some area of different permeability, we should determine the boundary conditions. In this article for the first time the boundary conditions for the problem of fluid filtration in the reservoir with some discontinuity are considered. This discontinuity represents thin but long area, which can be hydraulic fracturing of tectonic fault. The obtained boundary condition equations allow us to take into account pressure difference above and below the section and different values of permeability.

Critical Elements in Reservoir Rocks of Produced Fluids Nevada and Utah August 2017

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simmons, Stuart

Critical and trace element data for drill cuttings from Beowawe, Dixie Valley, and Roosevelt Hot Springs-Blundell geothermal production fields, for drill cuttings from Uinta basin producing oil-gas wells, and from outcrops in the Sevier Thermal Anomaly-Utah.

Sbaa basin: A new oil-producing regino in Algeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baghdadli, S.M.

1988-08-01

Discovery of a paraffinic oil in 1980 in the Adrar area, the west part of the Algerian Sahara within the Sbaa half-graben depression, opens a new oil- and gas-bearing region in Algeria. The oil and gas fields are located on highly faulted structures generated by differential movements of basement blocks. Oil deposits are connected with tidal sandy sediments of Strunian and Tournaisian age and occur at depths of 500 to 1,000 m (1,640 to 3,280 ft). Gas and wet gas deposits are related to sandstone reservoirs of Cambrian-Ordovician age at depths of 1,500 to 2,000 m (4,920 to 6,562 ft).

Life cycle water demand coefficients for crude oil production from five North American locations.

PubMed

Ali, Babkir; Kumar, Amit

2017-10-15

The production of liquid fuels from crude oil requires water. There has been limited focus on the assessment of life cycle water demand footprints for crude oil production and refining. The overall aim of this paper is address this gap. The objective of this research is to develop water demand coefficients over the life cycle of fuels produced from crude oil pathways. Five crude oil fields were selected in the three North American countries to reflect the impact of different spatial locations and technologies on water demand. These include the Alaska North Slope, California's Kern County heavy oil, and Mars in the U.S.; Maya in Mexico; and Bow River heavy oil in Alberta, Canada. A boundary for an assessment of the life cycle water footprint was set to cover the unit operations related to exploration, drilling, extraction, and refining. The recovery technology used to extract crude oil is one of the key determining factors for water demand. The amount of produced water that is re-injected to recover the oil is essential in determining the amount of fresh water that will be required. During the complete life cycle of one barrel of conventional crude oil, 1.71-8.25 barrels of fresh water are consumed and 2.4-9.51 barrels of fresh water are withdrawn. The lowest coefficients are for Bow River heavy oil and the highest coefficients are for Maya crude oil. Of all the unit operations, exploration and drilling require the least fresh water (less than 0.015 barrel of water per barrel of oil produced). A sensitivity analysis was conducted and uncertainty in the estimates was determined. Copyright © 2017 Elsevier Ltd. All rights reserved.

Reserve Growth in Oil Fields of West Siberian Basin, Russia

USGS Publications Warehouse

Verma, Mahendra K.; Ulmishek, Gregory F.

2006-01-01

Although reserve (or field) growth has proven to be an important factor contributing to new reserves in mature petroleum basins, it is still a poorly understood phenomenon. Limited studies show that the magnitude of reserve growth is controlled by several major factors, including (1) the reserve booking and reporting requirements in each country, (2) improvements in reservoir characterization and simulation, (3) application of enhanced oil recovery techniques, and (4) the discovery of new and extensions of known pools in discovered fields. Various combinations of these factors can affect the estimates of proven reserves in particular fields and may dictate repeated estimations of reserves during a field's life. This study explores the reserve growth in the 42 largest oil fields in the West Siberian Basin, which contain about 55 percent of the basin's total oil reserves. The West Siberian Basin occupies a vast swampy plain between the Ural Mountains and the Yenisey River, and extends offshore into the Kara Sea; it is the richest petroleum province in Russia. About 600 oil and gas fields with original reserves of 144 billion barrels of oil (BBO) and more than 1,200 trillion cubic feet of gas (TCFG) have been discovered. The principal oil reserves and most of the oil fields are in the southern half of the basin, whereas the northern half contains mainly gas reserves. Sedimentary strata in the basin consist of Upper Triassic through Tertiary clastic rocks. Most oil is produced from Neocomian (Lower Cretaceous) marine to deltaic sandstone reservoirs, although substantial oil reserves are also in the marine Upper Jurassic and continental to paralic Lower to Middle Jurassic sequences. The majority of oil fields are in structural traps, which are gentle, platform-type anticlines with closures ranging from several tens of meters to as much as 150 meters (490 feet). Fields producing from stratigraphic traps are generally smaller except for the giant Talin field which contains oil in Jurassic river-valley sandstones. Principal source rocks are organic-rich marine shales of the Volgian (uppermost Jurassic) Bazhenov Formation, which is 30-50 m (98- 164 feet) thick. Bazhenov-derived oils are mostly of medium gravity, and contain 0.8-1.3 percent sulfur and 2-5 percent paraffin. Oils in the Lower to Middle Jurassic clastics were sourced from lacustrine and estuarine shales of the Toarcian Togur Bed. These oils are medium to low gravity, with low sulfur (less than 0.25 percent) and high paraffin (commonly to 10 percent) contents. Among the 42 fields analyzed for reserve growth, 30 fields are located in the Middle Ob region, which includes the Samotlor field with reserves of more than 25 BBO and the Fedorov field with reserves of about 5 BBO. Data used in the study include year of discovery, year of first production, annual and cumulative production, and remaining reserves reported by Russian reserve categories (A+B+C1 and C2) in January of each year. Correlation of these Russian resource categories to U.S. categories of the Society of Petroleum Engineers classification is complex and somewhat uncertain. Reserve growth in oil fields of West Siberia was calculated using a newly developed Group Growth method, which requires that the total reserve (proven reserve plus cumulative production) of individual fields with an equal length of reserve record be added together starting with discovery year or the first production year. Then the annual growth factor (AGF), which is the ratio of total reserves of two consecutive years, is calculated for all years. Once AGFs have been calculated, the cumulative growth factor (CGF) is calculated by multiplying the AGFs of all the previous years. The CGF data are used to develop reserve growth models. The West Siberian oil fields show a 13-fold reserve growth 20 years after the discovery year and only about a 2-fold growth after the first production year. This difference is attributed to extensive exploration and field delineation activities between the discovery and the first production years. Because of uncertainty in the length of evaluation time and in reported reserves during this initial period, reserve growth based on the first production year is more reliable for model development. However, reserve growth models based both on discovery year and first production year show rapid growth in the first few years and slower growth in the following years. In contrast, the reserve growth patterns for the conterminous United States and offshore Gulf of Mexico show a steady reserve increase throughout the productive lives of the fields. The different reserve booking requirements and the lack of capital investment for improved reservoir management and production technologies in West Siberian fields relative to U.S. fields are the probable causes for the difference in growth patterns. Reserve growth models based on the first production year predict that the reserve growth potential in the 42 largest oil fields of West Siberia over a five-year period (1998-2003) ranges from 270-330 million barrels or 0.34-0.42 percent per year. For a similar five-year period (1996-2001), models for the conterminous United States predict a growth of 0.54-0.75 percent per year. This abstract presents the contents of a poster prepared for the AAPG Hedberg Research Conference on Understanding World Oil Resources, November 12-17, 2006 - Colorado Springs, Colorado. A paper 'Reserve Growth in Oil Fields of West Siberian Basin, Russia' was published in Natural Resources Research, v. 12, no. 2, June, 2003.

Tracing enhanced oil recovery signatures in casing gases from the Lost Hills oil field using noble gases

USGS Publications Warehouse

Barry, Peter H.; Kulongoski, Justin; Landon, Matthew K.; Tyne, R.L.; Gillespie, Janice; Stephens, Michael; Hillegonds, D.J.; Byrne, D.J.; Ballentine, C.J.

2018-01-01

Enhanced oil recovery (EOR) and hydraulic fracturing practices are commonly used methods to improve hydrocarbon extraction efficiency; however the environmental impacts of such practices remain poorly understood. EOR is particularly prevalent in oil fields throughout California where water resources are in high demand and disposal of high volumes of produced water may affect groundwater quality. Consequently, it is essential to better understand the fate of injected (EOR) fluids in California and other subsurface petroleum systems, as well as any potential effect on nearby aquifer systems. Noble gases can be used as tracers to understand hydrocarbon generation, migration, and storage conditions, as well as the relative proportions of oil and water present in the subsurface. In addition, a noble gas signature diagnostic of injected (EOR) fluids can be readily identified. We report noble gas isotope and concentration data in casing gases from oil production wells in the Lost Hills oil field, northwest of Bakersfield, California, and injectate gas data from the Fruitvale oil field, located within the city of Bakersfield. Casing and injectate gas data are used to: 1) establish pristine hydrocarbon noble-gas signatures and the processes controlling noble gas distributions, 2) characterize the noble gas signature of injectate fluids, 3) trace injectate fluids in the subsurface, and 4) construct a model to estimate EOR efficiency. Noble gas results range from pristine to significantly modified by EOR, and can be best explained using a solubility exchange model between oil and connate/formation fluids, followed by gas exsolution upon production. This model is sensitive to oil-water interaction during hydrocarbon expulsion, migration, and storage at reservoir conditions, as well as any subsequent modification by EOR.

Geologic constraints to fluid flow in the Jurassic Arab D reservoir, eastern Saudi Arabia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laing, J.E.

1991-08-01

A giant oil field located in eastern Saudi Arabia has produced several billion barrels of 37{degree} API oil from fewer than 100 wells. The Upper Jurassic Arab Formation is the main producing unit, and is made up of a series of upward-shoaling carbonate and anhydrite members. Porous carbonates of the Arab D member make up the principle oil reservoir, and overlying Arab D anhydrite provides the seal. Principal reservoir facies are stromatoporoid-coral and skeletal grainstones. Reservoir drive is currently provided by flank water injection. Despite more than 30 years of flank water injection (1.5 billion bbl) into the northern areamore » of the field, a thick oil column remains in the Arab D reservoir. Geological factors which affect fluid flow in this area are (1) a downdip facies change from permeable skeletal-stromatoporoid limestone to less permeable micritic limestone, (2) vertical permeability barriers resulting from shoaling-upward cycles, (3) a downdip tar mat, (4) dolomite along the flanks in the upper portion of the reservoir, (5) highly permeable intervals within the skeletal-stromatoporoid limestone, and (6) an updip, north to south facies change from predominantly stromatoporoid-coral grainstone to skeletal grainstone. These factors are considered in reservoir modeling, simulation studies, and planning locations for both water injection and producer wells.« less

Emerald Field, Natrona County, Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swirczynski, R.P.

1978-01-01

The Emerald Field is located on the W.-central Casper Arch in Sect. Nos. 7, 8, 9, and 18, T37N, R84W, Natrona County, Wyo. The Notches Field located in Sect. Nos. 3 and 10, T37N, R85W is 5 miles west of the Emerald Field. Both the Emerald and Notches Field produce oil from structural traps in the Tensleep formation (Pennsylvanian).

The prepared mind. [Serendipitous discovery of demulsifier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, N.E.S.

Products derived from the work of scientists with serendipity, or an imagined faculty for making fluke discoveries by looking for one thing and finding another, include the well-known examples of Teflon, penicillin, X-rays, Velcro, nylon, saccharin, and Nutrasweet. This dream of every scientist came true for the author in the discovery of a dithiocarbamate compound that could be used as a water-clarifying agent for oil fields that produce water. The new agent enables oil companies to discharge water produced in offshore drilling facilities without upsetting the clarity of the aquatic environment. The EPA limit for oil in discharged water ismore » 48 ppm. Failure to maintain this limit will result in shutdown of the platform. The alternative is to pipe the produced water to onshore facilities for treatment before discharge, which costs a good bit more. The serendipitous discovery of the dithiocarbamate compound discussed here as a unique water-clarifying agent has also led to important fundamental advances. The new agent allows producers to use existing water treatment equipment and remain in compliance with the latest limits on oil content. This compound has made it more economical to operate offshore oil and gas production facilities in the Gulf of Mexico and the North Sea.« less

Mechanisms of sulfate removal from subsurface calcium chloride brines: Heletz-Kokhav oilfields, Israel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gavrieli, I.; Starinsky, A.; Spiro, B.

1995-09-01

The evolution of the Ca-chloride brines in the Heletz Formation, Lower Cretaceous, in the southern coastal plain of Israel was reconstructed through the study of its sulfate concentration and isotopic composition. Particular emphasis was given to the brine-oil interaction in the oilfields and to the sulfate depletion and lower SO{sub 4}/Cl ratio in brines in contact with hydrocarbons (oil brines) relative to {open_quotes}oil-free{close_quotes} from dry wells in the same oilfields. A method is presented for a calculation of the amount of sulfate removed from the original seawater in the various stages of its evolution to Ca-chloride brine. Eastward migration ofmore » the Messinian Ca-Chloride brine into the Heletz Formation was accompanied by dolomitization of the country rock. Final depletion of sulfate from the brines took place, and possibly still occurs, in the presence of crude oil in the oilfields. The two oil-producing fields, Heletz and Kokhav, occupy different areas on a Rayleigh distillation diagram. Sulfate depletion in both fields is accompanied by an increase in {delta}{sup 34}S{sub SO}{sub 4}, which reaches a maximum values of 59{per_thousand}. The above correlation is explained by bacterial sulfate reduction facilitated by the contact with the crude. Samples collected from the same boreholes at time intervals of several months show two opposing trends: sulfate concentration decrease accompanied by increase in {delta}{sup 34}S{sub SO}{sub 4}, and vice versa. While the first can be explained as in situ bacterial sulfate reduction, the latter attest to subsurface brine migration, as would be expected in oil-producing fields.« less

The Specter of an Oily Bear or Geopolitical Challenges of the Modern Russian Petro-State

DTIC Science & Technology

2009-02-15

and state-owned industries in order to create oil companies and acquire the rights to oil fields at bargain- basement prices. While some of these...power structure , a few did not. The end result was the arrest or exile of several oligarchs and the re-centralization of their oil companies under...article21712.shtml 29 purchase its LNG from Russia, Qatar , or other LNG-producing countries. Because Russia still needs Euros and Dollars in order

Corrosion Challenges for the Oil and Gas Industry in the State of Qatar

NASA Astrophysics Data System (ADS)

Johnsen, Roy

In Qatar oil and gas has been produced from onshore fields in more than 70 years, while the first offshore field delivered its first crude oil in 1965. Due to the atmospheric conditions in Qatar with periodically high humidity, high chloride content, dust/sand combined with the temperature variations, external corrosion is a big treat to the installations and connecting infrastructure. Internal corrosion in tubing, piping and process systems is also a challenge due to high H2S content in the hydrocarbon mixture and exposure to corrosive aquifer water. To avoid corrosion different type of mitigations like application of coating, chemical treatment and material selection are important elements. This presentation will review the experiences with corrosion challenges for oil & gas installations in Qatar including some examples of corrosion failures that have been seen.

CROSS SECTIONS AND FIELD MAPS: CHEROKEE AND BUG FIELDS, SAN JUAN COUNTY, UTAH, AND LITTLE UTE AND SLEEPING UTE FIELDS, MONTEZUMA COUNTY, COLORADO

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas C. Chidsey Jr; Craig D. Morgan; Kevin McClure

2003-12-01

Over 400 million barrels (64 million m{sup 3}) of oil have been produced from the shallow-shelf carbonate reservoirs in the Pennsylvanian (Desmoinesian) Paradox Formation in the Paradox Basin, Utah and Colorado. With the exception of the giant Greater Aneth field, the other 100 plus oil fields in the basin typically contain 2 to 10 million barrels (0.3-1.6 million m{sup 3}) of original oil in place. Most of these fields are characterized by high initial production rates followed by a very short productive life (primary), and hence premature abandonment. Only 15 to 25 percent of the original oil in place ismore » recoverable during primary production from conventional vertical wells. An extensive and successful horizontal drilling program has been conducted in the giant Greater Aneth field. However, to date, only two horizontal wells have been drilled in small Ismay and Desert Creek fields. The results from these wells were disappointing due to poor understanding of the carbonate facies and diagenetic fabrics that create reservoir heterogeneity. These small fields, and similar fields in the basin, are at high risk of premature abandonment. At least 200 million barrels (31.8 million m{sup 3}) of oil will be left behind in these small fields because current development practices leave compartments of the heterogeneous reservoirs undrained. Through proper geological evaluation of the reservoirs, production may be increased by 20 to 50 percent through the drilling of low-cost single or multilateral horizontal legs from existing vertical development wells. In addition, horizontal drilling from existing wells minimizes surface disturbances and costs for field development, particularly in the environmentally sensitive areas of southeastern Utah and southwestern Colorado.« less

Use of microbes for paraffin cleanup at Naval Petroleum Reserve No. 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giangiacomo, L.; Khatib, A.

1995-12-31

Naval Petroleum Reserve No. 3 (NPR-3), also known as Teapot Dome, is a government-owned oil field in Natrona County, Wyoming. It is an asymmetrical anticline located on the western edge of the Powder River Basin, just south of the Salt Creek Anticline. Production started in 1922, and today the field is a marginally economic stripper field with average production of less than 3 BOPD (0.5 m{sup 3}/D) per well. Total field production is about 1,800 BOPD (286 m{sup 3}/D). The Second Wall Creek Formation was waterflooded from 1979 until June 1992 with poor results due to the extensive natural fracturemore » system in this sandstone unit. Since water injection ceased, reservoir pressure has declined to very low levels. Liquids extraction and reinjection of the gas produced from high-GOR wells along the gas-oil contact continues, but the average gas cap pressure has fallen to approximately 150 psi (1.03 MPa) from an original pressure of 1,120 psi (7.72 MPa). Since the oil is highly paraffinic, wax deposition in the hydraulic fractures and the perforations has become a serious production problem. Microbial treatment was considered as a possible low-cost solution. Four wells were selected in the Second Wall Creek Reservoir with severe paraffin problems and production rates high enough to economically justify the treatment. Problems were experienced with the production of thick oil after approximately three months. This was interpreted to be a result of previously immobile paraffin being cleaned up. A slight decrease in the decline rate was seen in the wells, although some external factors cloud the interpretation. Microbial treatments were discontinued because of marginal economics. Three of the four wells produced additional oil and had a positive incremental cash flow. Oil viscosity tests did indicate that some positive microbial thinning was occurring, and changes to the treatment procedure may potentially yield more economic results in the future.« less

Thermotropic nanostructured gels with complex hierarchical structure and two gelling components for water shut-off and enhance of oil recovery

NASA Astrophysics Data System (ADS)

Altunina, L. K.; Kuvshinov, I. V.; Kuvshinov, V. A.; Kozlov, V. V.; Stasyeva, L. A.

2017-12-01

This work presents the results of laboratory and field tests of thermotropic composition MEGA with two simultaneously acting gelling components, polymer and inorganic. The composition is intended for improving oil recovery and water shut-off at oilfields developed by thermal flooding, and cyclic-steam stimulated oil production wells. The composition forms an in-situ "gel-in-gel" system with improved structural-mechanical properties, using reservoir or carrier fluid heat for gelling. The gel blocks water breakthrough into producing wells and redistribute fluid flows, thus increasing the oil recovery factor.

Altering Reservoir Wettability to Improve Production from Single Wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

W. W. Weiss

2006-09-30

Many carbonate reservoirs are naturally fractured and typically produce less than 10% original oil in place during primary recovery. Spontaneous imbibition has proven an important mechanism for oil recovery from fractured reservoirs, which are usually weak waterflood candidates. In some situations, chemical stimulation can promote imbibition of water to alter the reservoir wettability toward water-wetness such that oil is produced at an economic rate from the rock matrix into fractures. In this project, cores and fluids from five reservoirs were used in laboratory tests: the San Andres formation (Fuhrman Masho and Eagle Creek fields) in the Permian Basin of Texasmore » and New Mexico; and the Interlake, Stony Mountain, and Red River formations from the Cedar Creek Anticline in Montana and South Dakota. Solutions of nonionic, anionic, and amphoteric surfactants with formation water were used to promote waterwetness. Some Fuhrman Masho cores soaked in surfactant solution had improved oil recovery up to 38%. Most Eagle Creek cores did not respond to any of the tested surfactants. Some Cedar Creek anticline cores had good response to two anionic surfactants (CD 128 and A246L). The results indicate that cores with higher permeability responded better to the surfactants. The increased recovery is mainly ascribed to increased water-wetness. It is suspected that rock mineralogy is also an important factor. The laboratory work generated three field tests of the surfactant soak process in the West Fuhrman Masho San Andres Unit. The flawlessly designed tests included mechanical well clean out, installation of new pumps, and daily well tests before and after the treatments. Treatments were designed using artificial intelligence (AI) correlations developed from 23 previous surfactant soak treatments. The treatments were conducted during the last quarter of 2006. One of the wells produced a marginal volume of incremental oil through October. It is interesting to note that the field tests were conducted in an area of the field that has not met production expectations. The dataset on the 23 Phosphoria well surfactant soaks was updated. An analysis of the oil decline curves indicted that 4.5 lb of chemical produced a barrel of incremental oil. The AI analysis supports the adage 'good wells are the best candidates.' The generally better performance of surfactant in the high permeability core laboratory tests supports this observation. AI correlations were developed to predict the response to water-frac stimulations in a tight San Andres reservoir. The correlations maybe useful in the design of Cedar Creek Anticline surfactant soak treatments planned for next year. Nuclear Magnetic Resonance scans of dolomite cores to measure porosity and saturation during the high temperature laboratory work were acquired. The scans could not be correlated with physical measurement using either conventional or AI methods.« less

Wrenching and oil migration, Mervine field, Kay County, Oklahoma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, H.G.

1985-02-01

Since 1913, Mervine field (T27N, R3E) has produced oil from 11 Mississippian and Pennsylvanian zones, and gas from 2 Permian zones. The field exhibits an impressive asymmetric surface anticline, with the steeper flank dipping 30/sup 0/E maximum. A nearly vertical, basement-involved fault develops immediately beneath the steeper flank of the surface anticline. Three periods of left-lateral wrench faulting account for 93% of all structural growth: 24% in post-Mississippian-pre-Desmoinesian time, 21% in Virgilian time, and 48% in post-Wolfcampian time. In Mesozoic through early Cenozoic times, the Devonian Woodford Shale (and possibly the Desmoinesian Cherokee shales) locally generated oil, which should havemore » been structurally trapped in the Ordovician Bromide sandstone. This oil may have joined oil already trapped in the Bromide, which had migrated to the Mervine area in the Early Pennsylvanian from a distant source. Intense post-Wolfcampian movement(s) fractured the competent pre-Pennsylvanian rocks, allowing Bromide brine and entrained oil to migrate vertically up the master fault, finally accumulating in younger reservoirs. Pressure, temperature, and salinity anomalies attest to vertical fluid migration continuing at the present time at Mervine field. Consequently, pressure, temperature, and salinity mapping should be considered as valuable supplements to structural and lithologic mapping when prospecting for structural hydrocarbon accumulations in epicratonic provinces.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartshorn, K.G.

The Castilla and Chichimene NE fields, operated by Chevron, are located in the southern Llanos basin of Colombia. The Castilla field, with an estimated 2.3 billion BBLS OOIP, produces heavy 14{prime} API oil, while the Chichimene NE field with an estimated 480 MMBBLS OOIP, produces a lighter 20{prime} API oil. Production is from multiple sandstone reservoirs of the Tertiary San Fernando and the Cretaceous Guadalupe Formations, and from massive non-marine sands of the Cretaceous Une Formation. Early problems with water coning and high water cuts led to detailed geologic study and engineering simulation to determine the most effective methods ofmore » reservoir management. The fresh nature of the connate water made evaluation more complicated, but results of RST (Reservoir Saturation Tool) logging runs on producing wells support the conclusions of the simulation studies regarding the potential for vertical drainage of the reservoir. As a result, the massive sands of the Une Formation can be perforated in the upper portion of the reservoir only, still enabling effective drainage of the lower reservoir while reducing water production and coning problems.« less

Graphic comparison of reserve-growth models for conventional oil and accumulation

USGS Publications Warehouse

Klett, T.R.

2003-01-01

The U.S. Geological Survey (USGS) periodically assesses crude oil, natural gas, and natural gas liquids resources of the world. The assessment procedure requires estimated recover-able oil and natural gas volumes (field size, cumulative production plus remaining reserves) in discovered fields. Because initial reserves are typically conservative, subsequent estimates increase through time as these fields are developed and produced. The USGS assessment of petroleum resources makes estimates, or forecasts, of the potential additions to reserves in discovered oil and gas fields resulting from field development, and it also estimates the potential fully developed sizes of undiscovered fields. The term ?reserve growth? refers to the commonly observed upward adjustment of reserve estimates. Because such additions are related to increases in the total size of a field, the USGS uses field sizes to model reserve growth. Future reserve growth in existing fields is a major component of remaining U.S. oil and natural gas resources and has therefore become a necessary element of U.S. petroleum resource assessments. Past and currently proposed reserve-growth models compared herein aid in the selection of a suitable set of forecast functions to provide an estimate of potential additions to reserves from reserve growth in the ongoing National Oil and Gas Assessment Project (NOGA). Reserve growth is modeled by construction of a curve that represents annual fractional changes of recoverable oil and natural gas volumes (for fields and reservoirs), which provides growth factors. Growth factors are used to calculate forecast functions, which are sets of field- or reservoir-size multipliers. Comparisons of forecast functions were made based on datasets used to construct the models, field type, modeling method, and length of forecast span. Comparisons were also made between forecast functions based on field-level and reservoir- level growth, and between forecast functions based on older and newer data. The reserve-growth model used in the 1995 USGS National Assessment and the model currently used in the NOGA project provide forecast functions that yield similar estimates of potential additions to reserves. Both models are based on the Oil and Gas Integrated Field File from the Energy Information Administration (EIA), but different vintages of data (from 1977 through 1991 and 1977 through 1996, respectively). The model based on newer data can be used in place of the previous model, providing similar estimates of potential additions to reserves. Fore-cast functions for oil fields vary little from those for gas fields in these models; therefore, a single function may be used for both oil and gas fields, like that used in the USGS World Petroleum Assessment 2000. Forecast functions based on the field-level reserve growth model derived from the NRG Associates databases (from 1982 through 1998) differ from those derived from EIA databases (from 1977 through 1996). However, the difference may not be enough to preclude the use of the forecast functions derived from NRG data in place of the forecast functions derived from EIA data. Should the model derived from NRG data be used, separate forecast functions for oil fields and gas fields must be employed. The forecast function for oil fields from the model derived from NRG data varies significantly from that for gas fields, and a single function for both oil and gas fields may not be appropriate.

GEOPHYSICAL WELL LOG/CORE DESCRIPTIONS, CHEROKEE AND BUG FIELDS, SAN JUAN COUNTY, UTAH, AND LITTLE UTE AND SLEEPING UTE FIELDS, MONTEZUMA COUNTY, COLORADO

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas C. Chidsey Jr; David E. Eby; Laura L. Wray

2003-12-01

Over 400 million barrels (64 million m{sup 3}) of oil have been produced from the shallow-shelf carbonate reservoirs in the Pennsylvanian (Desmoinesian) Paradox Formation in the Paradox Basin, Utah and Colorado. With the exception of the giant Greater Aneth field, the other 100 plus oil fields in the basin typically contain 2 to 10 million barrels (0.3-1.6 million m{sup 3}) of original oil in place. Most of these fields are characterized by high initial production rates followed by a very short productive life (primary), and hence premature abandonment. Only 15 to 25 percent of the original oil in place ismore » recoverable during primary production from conventional vertical wells. An extensive and successful horizontal drilling program has been conducted in the giant Greater Aneth field. However, to date, only two horizontal wells have been drilled in small Ismay and Desert Creek fields. The results from these wells were disappointing due to poor understanding of the carbonate facies and diagenetic fabrics that create reservoir heterogeneity. These small fields, and similar fields in the basin, are at high risk of premature abandonment. At least 200 million barrels (31.8 million m{sup 3}) of oil will be left behind in these small fields because current development practices leave compartments of the heterogeneous reservoirs undrained. Through proper geological evaluation of the reservoirs, production may be increased by 20 to 50 percent through the drilling of low-cost single or multilateral horizontal legs from existing vertical development wells. In addition, horizontal drilling from existing wells minimizes surface disturbances and costs for field development, particularly in the environmentally sensitive areas of southeastern Utah and southwestern Colorado.« less

POROSITY/PERMEABILITY CROSS-PLOTS: CHEROKEE AND BUG FIELDS, SAN JUAN COUNTY, UTAH, AND LITTLE UTE AND SLEEPING UTE FIELDS, MONTEZUMA COUNTY, COLORADO

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas C. Chidsey Jr; David E. Eby; Laura L. Wray

2003-12-01

Over 400 million barrels (64 million m{sup 3}) of oil have been produced from the shallow-shelf carbonate reservoirs in the Pennsylvanian (Desmoinesian) Paradox Formation in the Paradox Basin, Utah and Colorado. With the exception of the giant Greater Aneth field, the other 100 plus oil fields in the basin typically contain 2 to 10 million barrels (0.3-1.6 million m{sup 3}) of original oil in place. Most of these fields are characterized by high initial production rates followed by a very short productive life (primary), and hence premature abandonment. Only 15 to 25 percent of the original oil in place ismore » recoverable during primary production from conventional vertical wells. An extensive and successful horizontal drilling program has been conducted in the giant Greater Aneth field. However, to date, only two horizontal wells have been drilled in small Ismay and Desert Creek fields. The results from these wells were disappointing due to poor understanding of the carbonate facies and diagenetic fabrics that create reservoir heterogeneity. These small fields, and similar fields in the basin, are at high risk of premature abandonment. At least 200 million barrels (31.8 million m{sup 3}) of oil will be left behind in these small fields because current development practices leave compartments of the heterogeneous reservoirs undrained. Through proper geological evaluation of the reservoirs, production may be increased by 20 to 50 percent through the drilling of low-cost single or multilateral horizontal legs from existing vertical development wells. In addition, horizontal drilling from existing wells minimizes surface disturbances and costs for field development, particularly in the environmentally sensitive areas of southeastern Utah and southwestern Colorado.« less

Unique, icy gathering system will serve Norman Wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hale, D.

One of the more unique communities on the Mackenzie River is Norman Wells, ca 90 miles south of the Arctic Circle and 450 air miles south of the Beaufort Sea. For over 50 yr, Norman Wells has been a major supplier of petroleum products to the Mackenzie Valley. The most unique aspect of Norman Wells is that it is underlain by a large reservoir of oil. Fifty wells in the area produce over 3000 bbl of light crude daily, which is refined locally. Esso Resources Canada Ltd. now is developing the field and expanding production. New facilities will include 151more » new wells for producing oil and injecting water, 6 artificial islands in the 3-mile wide river to accommodate gathering points, and a new central processing facility. The crude oil to be produced will be transported by Interprovincial Pipeline (NW) Ltd. from Norman Wells to Zama, Alta.« less

Dedicated Industrial Oilseed Crops as Metabolic Engineering Platforms for Sustainable Industrial Feedstock Production

PubMed Central

Zhu, Li-Hua; Krens, Frans; Smith, Mark A.; Li, Xueyuan; Qi, Weicong; van Loo, Eibertus N.; Iven, Tim; Feussner, Ivo; Nazarenus, Tara J.; Huai, Dongxin; Taylor, David C.; Zhou, Xue-Rong; Green, Allan G.; Shockey, Jay; Klasson, K. Thomas; Mullen, Robert T.; Huang, Bangquan; Dyer, John M.; Cahoon, Edgar B.

2016-01-01

Feedstocks for industrial applications ranging from polymers to lubricants are largely derived from petroleum, a non-renewable resource. Vegetable oils with fatty acid structures and storage forms tailored for specific industrial uses offer renewable and potentially sustainable sources of petrochemical-type functionalities. A wide array of industrial vegetable oils can be generated through biotechnology, but will likely require non-commodity oilseed platforms dedicated to specialty oil production for commercial acceptance. Here we show the feasibility of three Brassicaceae oilseeds crambe, camelina, and carinata, none of which are widely cultivated for food use, as hosts for complex metabolic engineering of wax esters for lubricant applications. Lines producing wax esters >20% of total seed oil were generated for each crop and further improved for high temperature oxidative stability by down-regulation of fatty acid polyunsaturation. Field cultivation of optimized wax ester-producing crambe demonstrated commercial utility of these engineered crops and a path for sustainable production of other industrial oils in dedicated specialty oilseeds. PMID:26916792

Dedicated Industrial Oilseed Crops as Metabolic Engineering Platforms for Sustainable Industrial Feedstock Production.

PubMed

Zhu, Li-Hua; Krens, Frans; Smith, Mark A; Li, Xueyuan; Qi, Weicong; van Loo, Eibertus N; Iven, Tim; Feussner, Ivo; Nazarenus, Tara J; Huai, Dongxin; Taylor, David C; Zhou, Xue-Rong; Green, Allan G; Shockey, Jay; Klasson, K Thomas; Mullen, Robert T; Huang, Bangquan; Dyer, John M; Cahoon, Edgar B

2016-02-26

Feedstocks for industrial applications ranging from polymers to lubricants are largely derived from petroleum, a non-renewable resource. Vegetable oils with fatty acid structures and storage forms tailored for specific industrial uses offer renewable and potentially sustainable sources of petrochemical-type functionalities. A wide array of industrial vegetable oils can be generated through biotechnology, but will likely require non-commodity oilseed platforms dedicated to specialty oil production for commercial acceptance. Here we show the feasibility of three Brassicaceae oilseeds crambe, camelina, and carinata, none of which are widely cultivated for food use, as hosts for complex metabolic engineering of wax esters for lubricant applications. Lines producing wax esters >20% of total seed oil were generated for each crop and further improved for high temperature oxidative stability by down-regulation of fatty acid polyunsaturation. Field cultivation of optimized wax ester-producing crambe demonstrated commercial utility of these engineered crops and a path for sustainable production of other industrial oils in dedicated specialty oilseeds.

Novel Downhole Electromagnetic Flowmeter for Oil-Water Two-Phase Flow in High-Water-Cut Oil-Producing Wells.

PubMed

Wang, Yanjun; Li, Haoyu; Liu, Xingbin; Zhang, Yuhui; Xie, Ronghua; Huang, Chunhui; Hu, Jinhai; Deng, Gang

2016-10-14

First, the measuring principle, the weight function, and the magnetic field of the novel downhole inserted electromagnetic flowmeter (EMF) are described. Second, the basic design of the EMF is described. Third, the dynamic experiments of two EMFs in oil-water two-phase flow are carried out. The experimental errors are analyzed in detail. The experimental results show that the maximum absolute value of the full-scale errors is better than 5%, the total flowrate is 5-60 m³/d, and the water-cut is higher than 60%. The maximum absolute value of the full-scale errors is better than 7%, the total flowrate is 2-60 m³/d, and the water-cut is higher than 70%. Finally, onsite experiments in high-water-cut oil-producing wells are conducted, and the possible reasons for the errors in the onsite experiments are analyzed. It is found that the EMF can provide an effective technology for measuring downhole oil-water two-phase flow.

Novel Downhole Electromagnetic Flowmeter for Oil-Water Two-Phase Flow in High-Water-Cut Oil-Producing Wells

PubMed Central

Wang, Yanjun; Li, Haoyu; Liu, Xingbin; Zhang, Yuhui; Xie, Ronghua; Huang, Chunhui; Hu, Jinhai; Deng, Gang

2016-01-01

First, the measuring principle, the weight function, and the magnetic field of the novel downhole inserted electromagnetic flowmeter (EMF) are described. Second, the basic design of the EMF is described. Third, the dynamic experiments of two EMFs in oil-water two-phase flow are carried out. The experimental errors are analyzed in detail. The experimental results show that the maximum absolute value of the full-scale errors is better than 5%, the total flowrate is 5–60 m3/d, and the water-cut is higher than 60%. The maximum absolute value of the full-scale errors is better than 7%, the total flowrate is 2–60 m3/d, and the water-cut is higher than 70%. Finally, onsite experiments in high-water-cut oil-producing wells are conducted, and the possible reasons for the errors in the onsite experiments are analyzed. It is found that the EMF can provide an effective technology for measuring downhole oil-water two-phase flow. PMID:27754412

Electric Power Generation from Low to Intermediate Temperature Resources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gosnold, William D.

This project was designed to test the concept on the Eland-Lodgepole Field near Dickinson, North Dakota in the Williston Basin. The field is in secondary-recovery water-flood and consists of 12 producing oil wells, 5 water injection wells and one disposal well. Water production at the site averages approximately 320 gallons per minute (20.2 l s-1) and the temperature is 100 ⁰C. Engineers at Ormat estimated power production potential with the existing resource to be approximately 350 kWh. Unfortunately, ownership of the field was transferred from Encore, Inc., to Denbury, Inc., within the first week of the project. After two yearsmore » of discussion and planning, Denbury decided not to pursue this project due to complications with the site location and its proximity to Patterson Lake. Attempts to find other partners operating in the Williston Basin were unsuccessful. Consequently, we were unable to pursue the primary objective of the project. However, during negations with Denbury and subsequent time spent contacting other potential partners, we focused on objectives 2 and 3 and developed a clear understanding of the potential for co-produced production in the Williston Basin and the best practices for developing similar projects. At least nine water bearing formations with temperatures greater than 90 ⁰C extend over areas of several 10s of km2. The total energy contained in the rock volume of those geothermal aquifers is 283.6 EJ (1 EJ = 1018 J). The total energy contained in the water volume, determined from porosities which range from 2 percent to 8 percent, is 6.8 EJ. The aquifers grouped by 10 ⁰C temperature bins (Table 1) include one or more formations due to the bowl-shape structure of the basin. Table 1. Summary of energy available in geothermal aquifers in the Williston Basin Analysis of overall fluid production from active wells, units, fields and formations in North Dakota showed that few sites co-produce sufficient fluid for significant power production with ORC technology. Average co-produced water for 10,480 wells is 3.2 gallons per minute (gpm). Even excluding the tight formations, Bakken and Three Forks, average co-produced water for the remaining 3,337 is only 5 gpm. The output of the highest producing well is 184 gpm and the average of the top 100 wells is 52 gpm. Due to the depth of the oil producing formations in the Williston Basin, typically 3 km or greater, pumps are operated slowly to prevent watering out thus total fluid production is purposefully maintained at low volumes. There remain potential possibilities for development of geothermal fluids in the Williston Basin. Unitized fields in which water production from several tens of wells is collected at a single site are good possibilities for development. Water production in the unitized fields is greater than 1000 gpm is several areas. A similar possibility occurs where infill-drilling between Bakken and Three Forks horizontal wells has created areas where large volumes of geothermal fluids are available on multi-well pads and in unitized fields. Although the Bakken produces small amounts of water, the water/oil ration is typically less than 1, the oil and water mix produced at the well head can be sent through the heat exchanger on an ORC. It is estimated that several tens of MWh of power could be generated by a distributed system of ORC engines in the areas of high-density drilling in the Bakken Formation. Finally, horizontal drilling in water bearing formations is the other possibility. Several secondary recovery water-flood projects in the basin are producing water above 100 ⁰C at rates of 300 gpm to 850 gpm. Those systems also could produce several tens of MWh of power with ORC technology. Objective 3 of the project was highly successful. The program has produced 5 PhDs, 7 MS, and 3 BS students with theses in geothermal energy. The team has involved 7 faculty in 4 different engineering and science disciplines, ChE, EE, GE, and Geol. The team has produced 26 peer-reviewed papers and 62 presentations at professional meetings. Faculty involved in the program developed five graduate level courses covering different elements in heat flow and geothermal energy that are now offered in the Harold Hamm School of Geology and Geological Engineering. Lessons learned – Keys to developing a successful project;1. Determine target formations; a. Data from oil and gas operators, state oil and gas regulatory agencies, and state geological surveys help to identify producing formations and their properties; 2. Determine the quantity of energy available in the target formations; a. A complete thermal analysis of the basin or region yields the most useful information; b. Critical data include: BHT, heat flow, stratigraphy, lithology, lithological properties, and thermal conductivity, subsurface structure; 3. Determine fluid production potential; a. State oil and gas regulatory agencies, and state geological surveys have data on oil, gas and water production. State Water Commission/Agencies have data on water quality, aquifers, and regulations; b. Consider single horizontal wells, multiple conventional wells, and unitized fields; 4. Calculate energy production capacity of each formation based on different well combination and power plant scenarios. This is a broad overview rather than a site specific analysis; 5. Research and understand the local electrical power industry. Obtain the PPA before committing to the project; 6. Work with the high-level personnel in the oil company partner. Obtain an MOU that addresses all issues in the project including what to expect if the company goes out of business, is bought out, changes management, etc; and 7. Be prepared for project delays.« less

Red Fork and lower Skinner sandstones in northwest Tecumseh field, Pottawatomie County, Oklahoma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dale, T.B.

1987-08-01

The Northwest Tecumseh field, discovered in 1978, produces from the Pennsylvanian Skinner and Red Fork sandstones at 4800 ft. The 50 wells had produced 6.4 million bbl of oil and 20.8 bcf of gas through 1986. The field is 4.5 mi long, 3/4 mi wide, and the vertical section contains up to 132 ft of sandstone with greater than 10% porosity. These stacked, interconnected north-northeast-trending, channel-fill sandstones are part of a much larger fluvial/distributary system. These channels flowed to the north and cut down into underlying, fossiliferous, carbonate-bearing marine shale. A pre-Pennsylvanian structural low, trending north-northeast, existed in the southernmore » half of the field and created a predisposition for the channel trend which continued through Red Fork and Skinner deposition. The north-northeast-trending sandstone complex, parallel with present-day regional structural strike, provides the excellent configuration for this efficient stratigraphic trap. The northern end of the field is marked by bifurcation of the channel complex and by the crosscutting of a younger clay-filled channel. Despite the lenticularity of the sandstone sequence, there appears to be a uniform gas-oil contact and minor southwestward tilt of the oil-water contact in the south part of the pool. The primary reservoir energy is provided by a dissolved gas drive, with some assistance from the 60-ft gas cap. The vertical oil column is 80 ft. These reservoir sandstones are fine-grained quartzarenites, and the dissolution of ferrodolomite has increased porosities up to 21%. Kaolinite is the predominant clay mineral and has a tendency to migrate and reduce permeability during production.« less

Sequence stratigraphy of the Aux Vases Sandstone: A major oil producer in the Illinois basin

USGS Publications Warehouse

Leetaru, H.E.

2000-01-01

The Aux Vases Sandstone (Mississippian) has contributed between 10 and 25% of all the oil produced in Illinois. The Aux Vases is not only an important oil reservoir but is also an important source of groundwater, quarrying stone, and fluorspar. Using sequence stratigraphy, a more accurate stratigraphic interpretation of this economically important formation can be discerned and thereby enable more effective exploration for the resources contained therein. Previous studies have assumed that the underlying Spar Mountain, Karnak, and Joppa formations interfingered with the Aux Vases, as did the overlying Renault Limestone. This study demonstrates that these formations instead are separated by sequence boundaries; therefore, they are not genetically related to each other. A result of this sequence stratigraphic approach is the identification of incised valleys, paleotopography, and potential new hydrocarbon reservoirs in the Spar Mountain and Aux Vases. In eastern Illinois, the Aux Vases is bounded by sequence boundaries with 20 ft (6 m) of relief. The Aux Vases oil reservoir facies was deposited as a tidally influenced siliciclastic wedge that prograded over underlying carbonate-rich sediments. The Aux Vases sedimentary succession consists of offshore sediment overlain by intertidal and supratidal sediments. Low-permeability shales and carbonates typically surround the Aux Vases reservoir sandstone and thereby form numerous bypassed compartments from which additional oil can be recovered. The potential for new significant oil fields within the Aux Vases is great, as is the potential for undrained reservoir compartments within existing Aux Vases fields.

Qatar: World Oil Report 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This paper reports on oil and gas operations that have taken a marked upturn in Qatar highlighted by production expansion projects. The long-delayed beginning of production from offshore supergiant North gas field was scheduled to begin at press time at a rate of 600 to 750 MMcfd and 50,000 bcpd. Delays in production startup were caused by gas leaks around casing strings in 14 of the 16 producing wells and by the Gulf war. The $1.3 billion Phase I of development included two 8-well platforms and three support structures, plus gas and condensate lines to an onshore NGL facility. Initially,more » gas will be utilized domestically. Eventually, 300 MMcfd will be re-injected into the old Dukhan oil field.« less

The effects of fractional wettability on microbial enhanced oil recovery

NASA Astrophysics Data System (ADS)

Wildenschild, D.; Armstrong, R. T.

2011-12-01

Microbial enhanced oil recovery (MEOR) is a tertiary oil recovery technology that has had inconsistent success at the field-scale, while lab-scale experiments are mostly successful. One potential reason for these inconsistencies is that the efficacy of MEOR in fractional-wet systems is unknown. Our MEOR strategy consists of the injection of ex situ produced metabolic byproducts produced by Bacillus mojavensis JF-2 (that lower interfacial tension via biosurfactant production) into fractional-wet cores containing residual oil. Fractional-wet cores tested were 50%, 25%, and 0% oil-wet and two different MEOR flooding solutions were tested; one solution contained both microbes and metabolic byproducts while the other contained only the metabolic byproducts. The columns were imaged with x-ray computed microtomography (CMT) after water flooding, and after MEOR, which allowed for the evaluation of the pore-scale processes taking place during MEOR and wettability effects. Results indicate that during MEOR the larger residual oil blobs in mostly fractional-wet pores and residual oil held under relatively low capillary pressures were the main fractions recovered, while residual oil blobs in purely oil-wet pores remained in place. Residual oil saturation, interfacial curvatures, and oil blob sizes were measured from the CMT images and used to develop a conceptual model for MEOR in fractional-wet systems. Overall, results indicate that MEOR was effective at recovering oil from fractional-wet systems with reported additional oil recovered (AOR) values between 44% and 80%; the highest AOR values were observed in the most oil-wet system.

Embedded digital oilfield model

NASA Astrophysics Data System (ADS)

Korovin, Iakov S.; Boldyreff, Anton S.

2017-10-01

In modern hard conditions for the whole worldwide oil production industry the problem of increasing volumes of produced oil has recently become vital. This problem concerns the existing oilfields cause due to low crude oil prices the possibilities to drill new ones has almost disappeared. In this paper, we describe a novel approach of oil production enhancement, based on online procedures of all oil field data processing. The essence is that we have developed a dynamic oilfield model that allows to simultaneously handle the information, stored in tNavigator, Schlumberger ECLIPSE 100/300 and other `popular' formats in parallel. The model is developed on the basis of convolutional neural networks. An example of successful industrial experiment is depicted.

Analysis of the heavy oil production technology effectiveness using natural thermal convection with heat agent recirculation method in reservoirs with varying initial water saturation

NASA Astrophysics Data System (ADS)

Osnos, V. B.; Kuneevsky, V. V.; Larionov, V. M.; Saifullin, E. R.; Gainetdinov, A. V.; Vankov, Yu V.; Larionova, I. V.

2017-01-01

The method of natural thermal convection with heat agent recirculation (NTC HAR) in oil reservoirs is described. The analysis of the effectiveness of this method for oil reservoir heating with the values of water saturation from 0 to 0.5 units is conducted. As the test element Ashalchinskoye oil field is taken. CMG STARS software was used for calculations. Dynamics of cumulative production, recovery factor and specific energy consumption per 1 m3 of crude oil produced in the application of the heat exchanger with heat agent in cases of different initial water saturation are defined and presented as graphs.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meeks, H.

The purpose of this article is to provide information on the reality and procedure of the Bureau of Land Management's Simultaneous Oil and Gas Leasing System, commonly called the Government Oil and Gas Lottery. The article is about noncompetitive leases. This kind of leasing is done through the Simultaneous Oil and Gas Leasing System. Lands that are not within any known geologic structure of a producing oil and gas field, commonly known as wildcat lands, are subject to leasing to the first qualified person making application for a lease. Such a lease is termed noncompetitive since the applicant is entitledmore » to the lease without competitive bidding. Most Federal oil and gas leases are obtained through noncompetitive leasing procedures.« less

Improved oil recovery using bacteria isolated from North Sea petroleum reservoirs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davey, R.A.; Lappin-Scott, H.

1995-12-31

During secondary oil recovery, water is injected into the formation to sweep out the residual oil. The injected water, however, follows the path of least resistance through the high-permeability zones, leaving oil in the low-permeability zones. Selective plugging of these their zones would divert the waterflood to the residual oil and thus increase the life of the well. Bacteria have been suggested as an alternative plugging agent to the current method of polymer injection. Starved bacteria can penetrate deeply into rock formations where they attach to the rock surfaces, and given the right nutrients can grow and produce exo-polymer, reducingmore » the permeability of these zones. The application of microbial enhanced oil recovery has only been applied to shallow, cool, onshore fields to date. This study has focused on the ability of bacteria to enhance oil recovery offshore in the North Sea, where the environment can be considered extreme. A screen of produced water from oil reservoirs (and other extreme subterranean environments) was undertaken, and two bacteria were chosen for further work. These two isolates were able to grow and survive in the presence of saline formation waters at a range of temperatures above 50{degrees}C as facultative anaerobes. When a solution of isolates was passed through sandpacks and nutrients were added, significant reductions in permeabilities were achieved. This was confirmed in Clashach sandstone at 255 bar, when a reduction of 88% in permeability was obtained. Both isolates can survive nutrient starvation, which may improve penetration through the reservoir. Thus, the isolates show potential for field trials in the North Sea as plugging agents.« less

Regional Analysis of the Effects of Oil and Gas Development on Groundwater Resources in California

NASA Astrophysics Data System (ADS)

Landon, M. K.; McMahon, P. B.; Kulongoski, J. T.; Ball, L. B.; Gillespie, J. M.; Shimabukuro, D.; Taylor, K. A.

2016-12-01

The California State Water Resources Control Board is collaborating with the U.S. Geological Survey to implement a Regional Monitoring Program (RMP) to assess potential interactions between oil/gas stimulation treatment and groundwater resources. The effects of stimulation on groundwater resources will be difficult to distinguish from the effects of other past or present components of oil and gas development. As a result, the RMP is designed to provide an overall assessment of the effects of oil and gas development on groundwater quality. During 2016-17, the study is focused on selected priority oilfields in the eastern and western portions of the San Joaquin Valley in Kern County to: (1) produce three-dimensional (3D) salinity maps, (2) characterize the chemical composition of groundwater and produced water, and (3) identify the extent to which fluids from oil and gas development may be moving into protected (total dissolved solids less than 10,000 milligrams per liter) groundwater at regional scales. Analysis of available salinity data near oil/gas fields indicates there are regional patterns to salinity depth profiles; however, data gaps between the depths of water and oil/gas wells are common. These results provide a foundation for more detailed oilfield-scale salinity mapping, which includes geophysical methods (borehole, surface, and airborne) to fill data gaps. The RMP sampling-well networks are designed to evaluate groundwater quality along transects from oil/gas fields into adjacent aquifers and consist of existing wells supplemented by monitoring-well installation in priority locations identified by using 3D visualization of hydrogeologic data. The analytes include constituents with different transport characteristics such as dissolved gases, inorganic components (brines), and petroleum compounds. Analytes were selected because of their potential usefulness for understanding processes and pathways by which fluids from oilfield sources reach groundwater.

THIN SECTION DESCRIPTIONS: LITTLE UTE AND SLEEPING UTE FIELDS, MONTEZUMA COUNTY, COLORADO

DOE Office of Scientific and Technical Information (OSTI.GOV)

David E. Eby; Laura L. Wray

2003-12-01

Over 400 million barrels (64 million m{sup 3}) of oil have been produced from the shallow-shelf carbonate reservoirs in the Pennsylvanian (Desmoinesian) Paradox Formation in the Paradox Basin, Utah and Colorado. With the exception of the giant Greater Aneth field, the other 100 plus oil fields in the basin typically contain 2 to 10 million barrels (0.3-1.6 million m{sup 3}) of original oil in place. Most of these fields are characterized by high initial production rates followed by a very short productive life (primary), and hence premature abandonment. Only 15 to 25 percent of the original oil in place ismore » recoverable during primary production from conventional vertical wells. An extensive and successful horizontal drilling program has been conducted in the giant Greater Aneth field in Utah (figure 1). However, to date, only two horizontal wells have been drilled in small Ismay and Desert Creek fields. The results from these wells were disappointing due to poor understanding of the carbonate facies and diagenetic fabrics that create reservoir heterogeneity. These small fields, and similar fields in the basin, are at high risk of premature abandonment. At least 200 million barrels (31.8 million m{sup 3}) of oil will be left behind in these small fields because current development practices leave compartments of the heterogeneous reservoirs undrained. Through proper geological evaluation of the reservoirs, production may be increased by 20 to 50 percent through the drilling of low-cost single or multilateral horizontal legs from existing vertical development wells. In addition, horizontal drilling from existing wells minimizes surface disturbances and costs for field development, particularly in the environmentally sensitive areas of southeastern Utah and southwestern Colorado.« less

Subsurface stratigraphy and oil fields in the Salem Limestone and associated rocks in Indiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keller, S.J.; Becker, L.E.

An area of 11 counties in southwestern Indiana was studied because (1) the subsurface geology of the Salem Limestone and associated rocks in the area contained numerous correlation discrepancies; (2) it was the locus of recent oil exploration and oil discoveries in these rocks; (3) the last subsurface study of this rock section was made in 1957; and (4) since that time, subsurface data from newly drilled petroleum-test wells have increased a hundredfold. Because of their abundance, geophysical logs were used extensively for correlation. Drill cuttings, where available, were also used in studying the rock units. The upper boundary ofmore » the Salem was based on geophysical-log correlations as supported by available drill cuttings. The lower boundary of the Salem was based on drill cuttings. Commercial oil is produced from porous calcarenite zones in the St. Louis and Salem Limestones and from coarsely crystalline limestone in the Harrodsburg Limestone. The lower part of the St. Louis Limestone yields oil from a porous carbonate rock that resembles Salem calcarenite and that we have formally named the Sission Member in the St. Louis. The Salem calcarenite facies ranges in thickness from a low of 10 percent of the total Salem in the southern part of the study area to a high of 80 percent in the northern part. Oil is produced from porous zones in the calcarenite. Oil production from the St. Louis, Salem, and Harrodsburg Limestones in Indiana amounted to 8,880,078 barrels as of December 31, 1978. Production in 1977 was 1,534,320 barrels, and production in 1978 was 1,157,450 barrels. About 80 percent of the 1977 and 1978 production came from Union-Bowman Consolidated and Sisson Fields in Gibson, Knox, and Pike counties and the Owensville North Consolidated and Mt. Carmel Consolidated Fields in Gibson County. 15 figures, 3 tables.« less

Open-source LCA tool for estimating greenhouse gas emissions from crude oil production using field characteristics.

PubMed

El-Houjeiri, Hassan M; Brandt, Adam R; Duffy, James E

2013-06-04

Existing transportation fuel cycle emissions models are either general and calculate nonspecific values of greenhouse gas (GHG) emissions from crude oil production, or are not available for public review and auditing. We have developed the Oil Production Greenhouse Gas Emissions Estimator (OPGEE) to provide open-source, transparent, rigorous GHG assessments for use in scientific assessment, regulatory processes, and analysis of GHG mitigation options by producers. OPGEE uses petroleum engineering fundamentals to model emissions from oil and gas production operations. We introduce OPGEE and explain the methods and assumptions used in its construction. We run OPGEE on a small set of fictional oil fields and explore model sensitivity to selected input parameters. Results show that upstream emissions from petroleum production operations can vary from 3 gCO2/MJ to over 30 gCO2/MJ using realistic ranges of input parameters. Significant drivers of emissions variation are steam injection rates, water handling requirements, and rates of flaring of associated gas.

Unitization of oil and gas fields in Texas. A study of legislative, administrative, and judicial policies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weaver, J.L.

1986-01-01

In the 1970s, the long lines of cars at gasoline stations, the blackouts, and the school and factory closings announced to the public that the United States had an ''energy crisis.'' In response, an outpouring of state and federal legislation sought to lessen the effects of the oil and gas shortages and to prevent their recurrence. By 1985, every oil- and gas-producing state but Texas has passed a compulsory unitization statute. ''Unitization'' is the joint, coordinated operation of all, or at least a large part, of an oil or gas reservoir by the owners of the separate tracts overlying themore » reservoir; only by such joint endeavors can the many owners of interests in oil and gas fields operate efficiently to recover as much as possible at the lowest cost. In this book, Jacqueline Lang Weaver explains why Texas failed to enact such a statute--and how Texas has achieved a substantial degree of unitization nonetheless.« less

Schaben field, Kansas: Improving performance in a Mississippian shallow-shelf carbonate

USGS Publications Warehouse

Montgomery, S.L.; Franseen, E.K.; Bhattacharya, S.; Gerlach, P.; Byrnes, A.; Guy, W.; Carr, T.R.

2000-01-01

Schaben field (Kansas), located along the northeastern shelf of the Hugoton embayment, produces from Mississippian carbonates in erosional highs immediately beneath a regional unconformity. Production comes from depths of around 4400 ft (1342 m) in partially dolomitized shelf deposits. A detailed reservoir characterization/simulation study, recently performed as part of a Department of Energy Reservoir Class Oil Field Demonstration Project, has led to important revision in explanations for observed patterns of production. Cores recovered from three new data wells identify three main facies: Spicule-rich wackestone-packstone, echinoderm wackestone/packstone/grainstone, and dolomitic mudstone-wackestone. Reservoir quality is highest in spicule-rich wackestone/packstones but is subject to a very high degree of vertical heterogeneity due to facies interbedding, silification, and variable natural fracturing. The oil reservoir is underlain by an active aquifer, which helps maintain reservoir pressure but supports significant water production. Reservoir simulation, using public-domain, PC-based software, suggests that infill drilling is an efficient approach to enhanced recovery. Recent drilling directed by simulation results has shown considerable success in improving field production rates. Results from the Schaben field demonstration project are likely to have wide application for independent oil and exploration companies in western Kansas.Schaben field (Kansas), located along the northeastern shelf of the Hugoton embayment, produces from Mississippian carbonates in erosional highs immediately beneath a regional unconformity. Production comes from depths of around 4400 ft (1342 m) in partially dolomitized shelf deposits. A detailed reservoir characterization/simulation study, recently performed as part of a Department of Energy Reservoir Class Oil Field Demonstration Project, has led to important revision in explanations for observed patterns of production. Cores recovered from three new data wells identify three main facies: spicule-rich wackestone-packstone, echinoderm wackestone/packstone/grainstone, and dolomitic mudstone-wackestone. Reservoir quality is highest in spicule-rich wackestone/packstones but is subject to a very high degree of vertical heterogeneity due to facies interbedding, silification, and variable natural fracturing. The oil reservoir is underlain by an active aquifer, which helps maintain reservoir pressure but supports significant water production. Reservoir simulation, using public-domain, PC-based software, suggests that infill drilling is an efficient approach to enhanced recovery. Recent drilling directed by simulation results has shown considerable success in improving field production rates. Results from the Schaben field demonstration project are likely to have wide application for independent oil and exploration companies in western Kansas.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The paper discusses the outlook for the gas and oil industries of the Far East. Large crude producing countries are upgrading their mature oil properties. Offshore gas fields are being found and developed as new pipeline infrastructures open several remote areas. Separate evaluations are given for China, Indonesia, India, Malaysia, Thailand, Viet Nam, Pakistan, Myanmar, Brunei, Philippines, and briefly for Cambodia, Bangladesh, Japan, Mongolia, Taiwan, Afghanistan, and the Malaysia-Thailand Joint Development Area.

Bioprocess for treating coproduced oily sands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Munnecke, D.M.; Ireland, J.

1996-12-31

The production of oil from certain oil fields creates significant amounts of oily sand which in many regulatory jurisdictions is regulated as a hazardous material, thus disposal costs can be significant. Environmental BioTechnologies, Inc. (San Carlos, CA) has developed a physical/biological treatment process that is able to economically treat these coproduced sands and produce a product that contains less than 2,000 ppm total petroleum hydrocarbons.

Particle bounce in a personal cascade impactor: a field evaluation.

PubMed

Hinds, W C; Liu, W C; Froines, J R

1985-09-01

The collection characteristics of five types of substrates (collection surfaces) used in personal cascade impactors were evaluated for particle bounce in the laboratory with lead dioxide dust, and in the field with brass pouring fume and brass grinding dust. The substrates tested were uncoated stainless steel, silicon grease-coated stainless steel, oil-saturated Millipore membrane filter, oil-saturated Teflon membrane filter and oil-saturated sintered stainless steel. The use of coated and uncoated stainless steel plates to collect lead dioxide dust produced no difference in measured mass median diameter (MMD); however, with brass grinding dust, there was a 50% decrease in measured MMD when uncoated stainless steel substrates were used, as compared with coated stainless steel substrates. Oil-saturated Millipore membrane surfaces gave consistently lower MMDs than coated stainless steel surfaces. Coated and uncoated stainless steel gave similar MMDs when used to sample brass pouring fume. Oil-saturated Teflon membrane and oil-saturated sintered metal, surfaces for which the collection efficiency is presumed to be independent of the particle loading, gave MMDs similar to those measured for grease-coated stainless steel. The implications of these comparisons are discussed. It is concluded that bounce characteristics are strongly dependent on aerosol material and the suitability of collection surfaces needs to be determined by field evaluation.

Stratigraphic comparison of six oil fields (WV) producing from Big Injun sandstones

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zou, X.; Donaldson, A.C.

1993-08-01

Clustered within western West Virginia, six oil fields produce from the lower Mississippian Big Injun sandstones, and three more oil fields also supplement this production either from underlying Squaw or Weir sandstones. Shales separate these sandstones that occur stratigraphically between the Sunbury Shale (maximum flooding surface) and pre-Greenbrier unconformity (maximum regressive erosional surface), and represent highstand regressive deposits associated with the postorogenic phase of foreland basin accumulation. Stratigraphic studies show two Big Injun sandstones. The upper sandstone, called the Maccrady Big Injun, is separated from the lower Price/Pocono Big Injun sandstone by red shales. Both Big Injun sandstones consist ofmore » fine-grained river-mouth bars capped by coarse-grained river-channel deposits. Although the six fields are within three adjacent counties, Maccrady Big Injun sandstones of Blue Creek (Kanawha) and Rock Creek (Roane) fields are younger and were deposited by a different fluvial-deltaic system than the Price/Pocono Big Injun sandstones of Granny Creek (Clay), Tariff (Roane) Clendenin (Clay), and Pond Fork (Kanawha) fields. Upper Weir sandstones are thick, narrow north-trending belts underlying Pond Fork and Blue Creek fields, with properties suggesting wave-dominated shoreline deposits. Allocycles spanning separate drainage systems indicate eustasy. Postorogenic flexural adjustments probably explain stacked sandstone belts with superposed paleovalleys of overlying unconformities (pre-Greenbrier, Pottsville), particularly where aligned along or parallel basement structures of Rome trough or West Virginia dome. Initially, differential subsidence or uplift during sedimentation influenced the position, geometry, trend, and distribution patterns of these reservoir sandstone, then influenced their preserved condition during erosion of pre-Greenbrier unconformity.« less

North Sea Emerald crude oil assayed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rhodes, A.K.

1991-09-16

This book reports on an analysis of crude from Emerald field, 70 miles east of the Shetland Islands in the British North Sea, which shows that the crude is much heavier than typical North Sea crude. Elements of the long- delayed project appear to be in place, but production has not yet begun. Plans calls for producing the field at a rate of 30,000-40,000 b/d from a floating storage unit. Sovereign Oil and Gas plc has completed and fully tested seven production wells and four injectors in the marginal Emerald oil field. All flow lines are in place and themore » floating storage unit is ready to be installed. Production from Emerald will be sold to Neste Oy of Finland, at a minimum price of $17.90/bbl for Sullom Voe. Increases in spot prices above that level will be shared equally by the owners and purchaser.« less

Petrobras will increase its water injection in Bahia state (in Spanish)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1967-08-01

A plan for modernizing and expanding existing water- injection facilities for the Bahia fields is planned by Petrobras, the Brazilian oil monoply. The plan contemplates continued use of most of the original equipment. The plan will be expanded wih a pilot plant treatment of the Don Juan field brine, and the injection plant. The following engineering works will be started: (1) a pumping station which takes 110,000 bpd of water from the sea, (2) a water pipe line 80 k long; (3) a system for the collection of oil field brine; (4) 3 combination water treating plants; (5) 3 highmore » pressure injection pump stations; (6) a system for the distribution of the injection water; and (7) a pilot plant for treating well water. For water injection, it will be possible to use individually, seawater, well water, and brine produced with the oil.« less

Secondary recovery from the Dune Field, Crane County, Texas, is viable through mine workings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayler, M.F.

1991-03-01

Data in Report of Investigations No. 168, published by the Bureau of Economic Geology, University of Texas, indicate the Dune field is a good candidate for secondary recovery of mobile residual oil through an oil mine as described in US Patent {number sign}4,458,945. If trends identified in RI No. 168 can be extended into adjacent sections, oil recovery in the range of $10.00 per barrel or less should be possible. Mine workings will permit a more detailed mapping field jointing and fracturing, in turn permitting better placement of wells on 1 acre or closer spacing. Shafts to the surface wouldmore » be a mile or more apart greatly decreasing environmental impact. Wastewater generated could be re-introduced to assist in retaining reservoir pressures. If mine workings are driven in hard limestones, as would be possible in the Dune field, produced mine spoil would be marketable as gravel for the concrete industry.« less

Downhole Measurements of Electrokinetic Potential to Monitor Flow in Oilfields

NASA Astrophysics Data System (ADS)

Saunders, J.; Jackson, M.; Pain, C.; Addiego-Guevara, E.

2005-12-01

Oil companies currently produce an average of three barrels of water for each barrel of oil, which is expensive and environmentally unfriendly: the produced water is contaminated and must be treated and disposed of carefully. Ideally, water production would be prevented or minimised by monitoring its movement within the reservoir and responding appropriately. We suggest that measurements of electrokinetic (or ' streaming') potential during oil production, using permanently installed downhole electrodes, could be used to monitor water encroachment towards a well before water breakthrough occurs. Electrokinetic potentials are generated when fluids flow through rock, and although they are increasingly being used in other areas of earth science to monitor subsurface flows, there has been little investigation of their utility in hydrocarbon reservoirs. We have used a new numerical model to simulate the electrokinetic potential measured at a well during oil production, with reservoir pressure maintained by water injection or aquifer influx. Our results suggest that encroaching water causes changes in the electrokinetic potential at the well which could be resolved above background electrical noise; indeed, water approaching the well could be monitored several 10s to 100s of metres away. Our results differ from those obtained previously, because we include the results of recent laboratory experiments which provide new insight into the nature of the coupling between fluid and electrokinetic potentials as the oil saturation changes. Moreover, we investigate a range of production rates which are more appropriate for modern offshore developments, and simulate the potential measured at electrodes installed at the producing well rather than at a nearby monitoring well or at the surface. Electrodes mounted downhole on insulated casing have been successfully applied in subsurface resistivity surveys during oil production, and similar technology could be used to measure electrokinetic potential. If the producing well is equipped with downhole inflow control valves (so called ' intelligent' well technology), then oil production can be significantly enhanced if encroaching water is detected before it arrives and flow into the wellbore properly controlled. These findings raise the prospect of an oil field in which the wells can monitor the approach of water and respond appropriately. Such wells offer enormous potential economic and environmental benefits, particularly in fields which are difficult to access or dangerous to operate.

Geologic evolution of the Kastel trough and its implications on the Adiyaman oil fields, SE Turkey

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coskun, Bu.

1990-05-01

Oil field developments of the Adiyaman area one of the main oil producing zones in southeast Turkey, have been highly influenced by geologic evolution of the Kastel trough which is situated in front of the suture zone between the Arabian and Anatolian plates. The Upper Cretaceous movements created many paleostructural trends in the Kastel trough where important dolomitic and porous reservoirs exist. The most important tectonic event, which appeared during the Upper Cretaceous movements, is the accumulation of the Kocali-Karadut ophiolitic complex, advancing from the north to the south in the Kastel trough, where heavy materials caused formation of amore » structural model favoring generation and migration and entrapment of oil in the reservoir rocks. Due to the presence of the Kocali-Karadut complex in the Kastel trough the following zones have been distinguished. (1) North Uplift Area. Situated under the allochthonous units, many thrust and reverse faults characterize this zone. The presence of paleohighs, where primary dolomites develop, allows the appearance of some oil fields in the region. This is the main future exploration zone in southeast Turkey. (2) Accumulation Area. Advancing from the north to the south, the allochthonous Kocali-Karadut complex filled the Kastel trough creating a deep graben whose flanks present generally normal faults. (3) Structural Belt. Important paleohighs constitute an exploration trend in this zone where dolomitic and porous carbonates contain actual oil fields. (4) South Accumulation Area. Distant from the Arabian-Anatolian suture zone, regional tectonics and sedimentology show this zone remained deeply buried during geologic time; good source rocks were deposited during the Cretaceous. (5) South Uplift Area. This area corresponds to the northern flank of the huge regional Mardin high in southeast Turkey where new oil fields have been discovered.« less

Gas, Oil, and Water Production from Jonah, Pinedale, Greater Wamsutter, and Stagecoach Draw Fields in the Greater Green River Basin, Wyoming

USGS Publications Warehouse

Nelson, Philip H.; Ewald, Shauna M.; Santus, Stephen L.; Trainor, Patrick K.

2010-01-01

Gas, oil, and water production data were compiled from selected wells in four gas fields in rocks of Late Cretaceous age in southwestern Wyoming. This study is one of a series of reports examining fluid production from tight-gas reservoirs, which are characterized by low permeability, low porosity, and the presence of clay minerals in pore space. Production from each well is represented by two samples spaced five years apart, the first sample typically taken two years after commencement of production. For each producing interval, summary diagrams of oil versus gas and water versus gas production show fluid production rates, the change in rates during five years, the water-gas and oil-gas ratios, and the fluid type. These diagrams permit well-to-well and field-to-field comparisons. Fields producing water at low rates (water dissolved in gas in the reservoir) can be distinguished from fields producing water at moderate or high rates, and the water-gas ratios are quantified. The ranges of first-sample gas rates in Pinedale field and Jonah field are quite similar, and the average gas production rate for the second sample, taken five years later, is about one-half that of the first sample for both fields. Water rates are generally substantially higher in Pinedale than in Jonah, and water-gas ratios in Pinedale are roughly a factor of ten greater in Pinedale than in Jonah. Gas and water production rates from each field are fairly well grouped, indicating that Pinedale and Jonah fields are fairly cohesive gas-water systems. Pinedale field appears to be remarkably uniform in its flow behavior with time. Jonah field, which is internally faulted, exhibits a small spread in first-sample production rates. In the Greater Wamsutter field, gas production from the upper part of the Almond Formation is greater than from the main part of the Almond. Some wells in the main and the combined (upper and main parts) Almond show increases in water production with time, whereas increases in water production are rare in the upper part of the Almond, and a higher percentage of wells in the upper part of the Almond show water decreasing at the same rate as gas than in the main or combined parts of the Almond. In Stagecoach Draw field, the gas production rate after five years is about one-fourth that of the first sample, whereas in Pinedale, Jonah, and Greater Wamsutter fields, the production rate after five years is about one-half that of the first sample. The more rapid gas decline rate seems to be the outstanding feature distinguishing Stagecoach Draw field, which is characterized as a conventional field, from Pinedale, Jonah, and Greater Wamsutter fields, which are generally characterized as tight-gas accumulations. Oil-gas ratios are fairly consistent within Jonah, Pinedale, and Stagecoach Draw fields, suggesting similar chemical composition and pressure-temperature conditions within each field, and are less than the 20 bbl/mmcf upper limit for wet gas. However, oil-gas ratios vary considerably from one area to another in the Greater Wamsutter field, demonstrating a lack of commonality in either chemistry or pressure-temperature conditions among the six areas. In all wells in all four fields examined here, water production commences with gas production-there are no examples of wells with water-free production and no examples where water production commences after first-sample gas production. The fraction of records with water production higher in the second sample than in the first sample varies from field to field, with Pinedale field showing the lowest percentage of such cases and Jonah field showing the most. Most wells have water-gas ratios exceeding the amount that could exist dissolved in gas at reservoir pressure and temperature.

Stratigraphy of Citronelle Oil Field, AL: Perspectives from Enhanced Oil Recovery and Potential CO2 Sequestration

NASA Astrophysics Data System (ADS)

Hills, D. J.; Pashin, J. C.; Kopaska-Merkel, D. C.; Esposito, R. A.

2008-12-01

The Citronelle Dome is a giant salt-cored anticline in the eastern Mississippi Interior Salt Basin of south Alabama. The dome forms an elliptical structural closure containing multiple opportunities for enhanced oil recovery (EOR) and large-capacity saline reservoir CO2 sequestration. The Citronelle Oil Field, which is on the crest of the dome, has produced more than 168 MMbbl of 42° gravity oil from marginal marine sandstone in the Lower Cretaceous Donovan Sand. Recently, EOR field tests have begun in the northeastern part of the oil field. Citronelle Unit B-19-10 #2 well (Alabama State Oil and Gas Board Permit No. 3232) will serve as the CO2 injector for the first field test. CO2 will be injected into the Upper Donovan 14-1 and 16-2 sandstone units. All well logs in the 4-square-mile area surrounding the test site have been digitized and used to construct a network of nineteen stratigraphic cross sections correlating Sands 12 through 20A in the Upper Donovan. Detailed study of Citronelle cores has shown that depositional environments in the Donovan Sand differed significantly from the earlier model that has guided past development of the Citronelle Field. The cross sections demonstrate the extreme facies heterogeneity of the Upper Donovan, and this heterogeneity is well expressed within the five-spot well pattern where the field test will be conducted. Many other features bearing on the performance of the CO2 injection test have been discovered. Of particular interest is the 16-2 sand, which is interpreted as a composite of two tiers of channel fills. Pay strata are typically developed in the lower tier, and this is where CO2 will be injected. The upper tier is highly heterogeneous and is interpreted to contain sandstone fills of variable reservoir quality, as well as mudstone plugs.

Silurian "Clinton" Sandstone Reservoir Characterization for Evaluation of CO2-EOR Potential in the East Canton Oil Field, Ohio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riley, Ronald; Wicks, John; Perry, Christopher

The purpose of this study was to evaluate the efficacy of using CO2-enhanced oil recovery (EOR) in the East Canton oil field (ECOF). Discovered in 1947, the ECOF in northeastern Ohio has produced approximately 95 million barrels (MMbbl) of oil from the Silurian “Clinton” sandstone. The original oil-in-place (OOIP) for this field was approximately 1.5 billion bbl and this study estimates by modeling known reservoir parameters, that between 76 and 279 MMbbl of additional oil could be produced through secondary recovery in this field, depending on the fluid and formation response to CO2 injection. A CO2 cyclic test (“Huff-n-Puff”) wasmore » conducted on a well in Stark County to test the injectivity in a “Clinton”-producing oil well in the ECOF and estimate the dispersion or potential breakthrough of the CO2 to surrounding wells. Eighty-one tons of CO2 (1.39 MMCF) were injected over a 20-hour period, after which the well was shut in for a 32-day “soak” period before production was resumed. Results demonstrated injection rates of 1.67 MMCF of gas per day, which was much higher than anticipated and no CO2 was detected in gas samples taken from eight immediately offsetting observation wells. All data collected during this test was analyzed, interpreted, and incorporated into the reservoir characterization study and used to develop the geologic model. The geologic model was used as input into a reservoir simulation performed by Fekete Associates, Inc., to estimate the behavior of reservoir fluids when large quantities of CO2 are injected into the “Clinton” sandstone. Results strongly suggest that the majority of the injected CO2 entered the matrix porosity of the reservoir pay zones, where it diffused into the oil. Evidence includes: (A) the volume of injected CO2 greatly exceeded the estimated capacity of the hydraulic fracture and natural fractures; (B) there was a gradual injection and pressure rate build-up during the test; (C) there was a subsequent, gradual flashout of the CO2 within the reservoir during the ensuing monitored production period; and (D) a large amount of CO2 continually off-gassed from wellhead oil samples collected as late as 3½ months after injection. After the test well was returned to production, it produced 174 bbl of oil during a 60-day period (September 22 to November 21, 2008), which represents an estimated 58 percent increase in incremental oil production over preinjection estimates of production under normal, conditions. The geologic model was used in a reservoir simulation model for a 700-acre model area and to design a pilot to test the model. The model was designed to achieve a 1-year response time and a five-year simulation period. The reservoir simulation modeling indicated that the injection wells could enhance oil production and lead to an additional 20 percent recovery in the pilot area over a five-year period. The base case estimated that by injecting 500 MCF per day of CO2 into each of the four corner wells, 26,000 STBO would be produced by the central producer over the five-year period. This would compare to 3,000 STBO if a new well were drilled without the benefit of CO2 injection. This study has added significant knowledge to the reservoir characterization of the “Clinton” in the ECOF and succeeded in identifying a range on CO2-EOR potential. However, additional data on fluid properties (PVT and swelling test), fractures (oriented core and microseis), and reservoir characteristics (relative permeability, capillary pressure, and wet ability) are needed to further narrow the uncertainties and refine the reservoir model and simulation. After collection of this data and refinement of the model and simulation, it is recommended that a larger scale cyclic- CO2 injection test be conducted to better determine the efficacy of CO2-EOR in the “Clinton” reservoir in the ECOF.« less

Silurian "Clinton" Sandstone Reservoir Characterization for Evaluation of CO2-EOR Potential in the East Canton Oil Field, Ohio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ronald Riley; John Wicks; Christopher Perry

The purpose of this study was to evaluate the efficacy of using CO2-enhanced oil recovery (EOR) in the East Canton oil field (ECOF). Discovered in 1947, the ECOF in northeastern Ohio has produced approximately 95 million barrels (MMbbl) of oil from the Silurian 'Clinton' sandstone. The original oil-in-place (OOIP) for this field was approximately 1.5 billion bbl and this study estimates by modeling known reservoir parameters, that between 76 and 279 MMbbl of additional oil could be produced through secondary recovery in this field, depending on the fluid and formation response to CO2 injection. A CO2 cyclic test ('Huff-n-Puff') wasmore » conducted on a well in Stark County to test the injectivity in a 'Clinton'-producing oil well in the ECOF and estimate the dispersion or potential breakthrough of the CO2 to surrounding wells. Eighty-one tons of CO2 (1.39 MMCF) were injected over a 20-hour period, after which the well was shut in for a 32-day 'soak' period before production was resumed. Results demonstrated injection rates of 1.67 MMCF of gas per day, which was much higher than anticipated and no CO2 was detected in gas samples taken from eight immediately offsetting observation wells. All data collected during this test was analyzed, interpreted, and incorporated into the reservoir characterization study and used to develop the geologic model. The geologic model was used as input into a reservoir simulation performed by Fekete Associates, Inc., to estimate the behavior of reservoir fluids when large quantities of CO2 are injected into the 'Clinton' sandstone. Results strongly suggest that the majority of the injected CO2 entered the matrix porosity of the reservoir pay zones, where it diffused into the oil. Evidence includes: (A) the volume of injected CO2 greatly exceeded the estimated capacity of the hydraulic fracture and natural fractures; (B) there was a gradual injection and pressure rate build-up during the test; (C) there was a subsequent, gradual flashout of the CO2 within the reservoir during the ensuing monitored production period; and (D) a large amount of CO2 continually off-gassed from wellhead oil samples collected as late as 3 1/2 months after injection. After the test well was returned to production, it produced 174 bbl of oil during a 60-day period (September 22 to November 21, 2008), which represents an estimated 58 percent increase in incremental oil production over preinjection estimates of production under normal, conditions. The geologic model was used in a reservoir simulation model for a 700-acre model area and to design a pilot to test the model. The model was designed to achieve a 1-year response time and a five-year simulation period. The reservoir simulation modeling indicated that the injection wells could enhance oil production and lead to an additional 20 percent recovery in the pilot area over a five-year period. The base case estimated that by injecting 500 MCF per day of CO2 into each of the four corner wells, 26,000 STBO would be produced by the central producer over the five-year period. This would compare to 3,000 STBO if a new well were drilled without the benefit of CO2 injection. This study has added significant knowledge to the reservoir characterization of the 'Clinton' in the ECOF and succeeded in identifying a range on CO2-EOR potential. However, additional data on fluid properties (PVT and swelling test), fractures (oriented core and microseis), and reservoir characteristics (relative permeability, capillary pressure, and wet ability) are needed to further narrow the uncertainties and refine the reservoir model and simulation. After collection of this data and refinement of the model and simulation, it is recommended that a larger scale cyclic-CO2 injection test be conducted to better determine the efficacy of CO2-EOR in the 'Clinton' reservoir in the ECOF.« less

An interdisciplinary approach to reservoir management: The Malu Field, West Niger Delta, Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patterson, B.A.; Bluhm, C.T.; Adokpaye, E.U.

The Malu Field is 175 kilometers southeast of Lagos, offshore Nigeria. The field was discovered in 1967 and brought on stream in 1971. Peak production reached 31,300 barrels per day in 1972. Twenty-six wells have been drilled in the thirty-six square kilometer size field. In 1990 original-oil-in-place was estimated at 345 million barrels with cumulative production of 109 million barrels and an estimated 40 million barrels of remaining reserves. The Main Field review was initiated in 1994 to resolve structural and production inconsistencies and therefore improve reservoir performance. The tools used include reprocessed three-dimensional seismic, oil chemistry (primarily gas chromatography),more » and production data. The complexly faulted field is subdivided into seven different fault blocks. Growth faults generally trend northwest to southeast and are downthrown to the west. Twenty-five different hydrocarbon-bearing sands have been identified within the field. These sands are separated into sixty-three different reservoirs by the series of southeast trending growth faults. Most sands are laterally continuous within mapped fault blocks except in east Malu. Cross-fault communication of oils occurs among several of the shallow reservoirs in west Malu allowing wells to deplete unintended horizons. In addition, three of the dual string completions are producing oil only from only the upper sands. The integration of seismic, oil chemistry, and production data allows more efficient management of production by providing accurate structure maps, reserve estimates, drainage pathways, and justification for workovers and future development drilling.« less

M-X Environmental Technical Report. Environmental Characteristics of Alternative Designated Deployment Areas, Mining and Geology.

DTIC Science & Technology

1980-12-22

Nevada and Utah Great Basin area, can be quickly drawn because of the paucity of known sites. The sole commercially producing area of oil and gas in...good production (in addition to oil shale, tar, sand and Gilsonite) is to be found in the Uinta Basin . Major production in Utah comes from the four...Utah crude came from these four fields. About 3,000 ni 2 (7,800 km 2 ) in the Uinta Basin in northeastern Utah is underlain by oil shale 15 ft (4.5 m

Avian diversity and feeding guilds in a secondary forest, an oil palm plantation and a paddy field in riparian areas of the kerian river basin, perak, malaysia.

PubMed

Azman, Nur Munira; Latip, Nurul Salmi Abdul; Sah, Shahrul Anuar Mohd; Akil, Mohd Abdul Muin Md; Shafie, Nur Juliani; Khairuddin, Nurul Liyana

2011-12-01

The diversity and the feeding guilds of birds in three different habitats (secondary forest, oil palm plantation and paddy field) were investigated in riparian areas of the Kerian River Basin (KRB), Perak, Malaysia. Point-count observation and mist-netting methods were used to determine bird diversity and abundance. A total of 132 species of birds from 46 families were recorded in the 3 habitats. Species diversity, measured by Shannon's diversity index, was 3.561, 3.183 and 1.042 in the secondary forest, the paddy field and the oil palm plantation, respectively. The vegetation diversity and the habitat structure were important determinants of the number of bird species occurring in an area. The relative abundance of the insectivore, insectivore-frugivore and frugivore guilds was greater in the forest than in the monoculture plantation. In contrast, the relative abundance of the carnivore, granivore and omnivore guilds was higher in the plantation. The results of the study show that the conversion of forest to either oil palm plantation or paddy fields produced a decline in bird diversity and changes in the distribution of bird feeding guilds.

Avian Diversity and Feeding Guilds in a Secondary Forest, an Oil Palm Plantation and a Paddy Field in Riparian Areas of the Kerian River Basin, Perak, Malaysia

PubMed Central

Azman, Nur Munira; Latip, Nurul Salmi Abdul; Sah, Shahrul Anuar Mohd; Akil, Mohd Abdul Muin Md; Shafie, Nur Juliani; Khairuddin, Nurul Liyana

2011-01-01

The diversity and the feeding guilds of birds in three different habitats (secondary forest, oil palm plantation and paddy field) were investigated in riparian areas of the Kerian River Basin (KRB), Perak, Malaysia. Point-count observation and mist-netting methods were used to determine bird diversity and abundance. A total of 132 species of birds from 46 families were recorded in the 3 habitats. Species diversity, measured by Shannon’s diversity index, was 3.561, 3.183 and 1.042 in the secondary forest, the paddy field and the oil palm plantation, respectively. The vegetation diversity and the habitat structure were important determinants of the number of bird species occurring in an area. The relative abundance of the insectivore, insectivore-frugivore and frugivore guilds was greater in the forest than in the monoculture plantation. In contrast, the relative abundance of the carnivore, granivore and omnivore guilds was higher in the plantation. The results of the study show that the conversion of forest to either oil palm plantation or paddy fields produced a decline in bird diversity and changes in the distribution of bird feeding guilds. PMID:24575217

Oil migration in a major growth fault: Structural analysis of the Pathfinder core, South Eugene Island Block 330, offshore Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Losh, S.

1998-09-01

The Pathfinder core, collected in the South Eugene Island Block 330 field, offshore Louisiana, provides an outstanding sample of structures associated with a major growth fault that abuts a giant oil field and that is thought to have acted as a conduit for hydrocarbon migration into the producing reservoirs. The fault zone in the core consists of three structural domains, each characterized by a distinct rock type, distribution of fault dips and dip azimuths, and distribution of spacing between adjacent faults and fractures. Although all of the domains contain oil-bearing sands, only faults and fractures in the deepest domain containmore » oil, even though the oil-barren fault domains contain numerous faults and fractures that are parallel to those containing oil in the deepest domain. The deepest domain is also distinguished from the other two domains by a greater degree of structural complexity and by a well-defined power-law distribution of fault and fracture spacings. Even though oil is present in sands throughout the core, its restriction to faults and fractures in the youngest sampled portion of the fault zone implies that oil migrated only through that part of the fault that was active during the time when oil had access to it. The absence of oil in fractures or faults in the other, probably older, fault domains indicates that the oil was never sufficiently pressured to flow up the fault zone on its own, either by hydraulic fracture or by increased permeability as a result of decreased effective stress. Instead, fluid migration along faults and fractures in the Pathfinder core was enhanced by permeability created in response to relatively far-field stresses related to minibasin subsidence.« less

Exploration limited since '70s in Libya's Sirte basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, D.

1995-03-13

Esso Standard made the first Libyan oil discovery in the western Ghadames basin in 1957. The Atshan-2 well tested oil from Devonian sandstones, and the play was a continuation of the Paleozoic trend found productive in the neighboring Edjeleh region of eastern Algeria. Exploration in the Sirte basin began in earnest in 1958. Within the next 10 years, 16 major oil fields had been discovered, each with recoverable reserves greater than 500 million bbl of oil. Libya currently produces under OPEC quota approximately 1.4 million b/d of oil, with discovered in-place reserves of 130 billion bbl of oil. The papermore » describes the structural framework, sedimentary basins of Libya, the Sirte basin, petroleum geology, play types, source rocks, generation and migration of hydrocarbons, oil reserves, potential, and acreage availability.« less

Biosurfactant production by Mucor circinelloides on waste frying oil and possible uses in crude oil remediation.

PubMed

Hasanizadeh, Parvin; Moghimi, Hamid; Hamedi, Javad

2017-10-01

Biosurfactants are biocompatible surface active agents which many microorganisms produce. This study investigated the production of biosurfactants by Mucor circinelloides. The effects of different factors on biosurfactant production, including carbon sources and concentrations, nitrogen sources, and iron (II) concentration, were studied and the optimum condition determined. Finally, the strain's ability to remove the crude oil and its relationship with biosurfactant production was evaluated. The results showed that M. circinelloides could reduce the surface tension of the culture medium to 26.6 mN/m and create a clear zone of 12.9 cm diameter in an oil-spreading test. The maximum surface tension reduction was recorded 3 days after incubation. The optimum condition for biosurfactant production was achieved in the presence of 8% waste frying oil as a carbon source, 2 g/L yeast extract as a nitrogen source, and 0.01 mM FeSO 4 . M. circinelloides could consume 8% waste frying oil in 5 days of incubation, and 87.6% crude oil in 12 days of incubation. A direct correlation was observed between oil degradation and surface tension reduction in the first 3 days of fungal growth. The results showed that the waste frying oil could be recommended as an inexpensive oily waste substance for biosurfactant production, and M. circinelloides could have the potential to treat waste frying oil. According to the results, the produced crude biosurfactant or fungal strain could be directly used for the mycoremediation of crude oil contamination in oil fields.

Using IR spectroscopy to determine biodiesel conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tirla, Cornelia; Dooling, Thomas; Smith, Rachel B.

This project’s aim was to develop a way to use Infrared (IR) Spectroscopy to determine the extent of the conversion of oil to biodiesel produced during a typical transesterification process. The most reliable method of biodiesel analysis is gas chromatography with flame ionization detector (GC-FID) analysis. This analysis is not ideal for the educational or field applications since it is time intensive and requires expensive, specialized equipment. The use of the FT-IR is faster and more affordable. A calibration curve was created by comparing data on the purity of biodiesel samples obtained from the GC-FID analysis to the ratio ofmore » the absorbances at 1197 cm -1 to 1166 cm -1 from the FT-IR spectrum. For field application, a similar method was developed using a portable IR spectrometer, the InfraSpecTM VFA-IR spectrometer. As a result, the data collected gave a good linear fit for % purity of the samples and can be used as a method for monitoring the conversion of different types of oils to biodiesel and determining the purity of biodiesel produced from oil.« less

Using IR spectroscopy to determine biodiesel conversion

DOE PAGES

Tirla, Cornelia; Dooling, Thomas; Smith, Rachel B.; ...

2013-01-01

This project’s aim was to develop a way to use Infrared (IR) Spectroscopy to determine the extent of the conversion of oil to biodiesel produced during a typical transesterification process. The most reliable method of biodiesel analysis is gas chromatography with flame ionization detector (GC-FID) analysis. This analysis is not ideal for the educational or field applications since it is time intensive and requires expensive, specialized equipment. The use of the FT-IR is faster and more affordable. A calibration curve was created by comparing data on the purity of biodiesel samples obtained from the GC-FID analysis to the ratio ofmore » the absorbances at 1197 cm -1 to 1166 cm -1 from the FT-IR spectrum. For field application, a similar method was developed using a portable IR spectrometer, the InfraSpecTM VFA-IR spectrometer. As a result, the data collected gave a good linear fit for % purity of the samples and can be used as a method for monitoring the conversion of different types of oils to biodiesel and determining the purity of biodiesel produced from oil.« less

Improved reservoir characterization of the Rose Run sandstone on the East Randolph Field, Portage County, Ohio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Safley, I.E.; Thomas, J.B.

1996-09-01

The East Randolph Field, located in Randolph Township, Portage County, Ohio, produces oil and gas from the Cambrian Rose Run sandstone unit, a member of the Knox Supergroup. Field development and infill drilling opportunities illustrate the need for improved reservoir characterization of the hydrocarbon productive intervals. This reservoir study is conducted under the Department of Energy`s Reservoir Management Program with professionals from BDM-Oklahoma and Belden & Blake Corporation. Well log and core analyses were conducted to determine the reservoir distribution, the heterogeneity of the hydrocarbon producing intervals, and the effects of faulting and fracturing on well productivity. The Rose Runmore » sandstones and interbedded dolomites were subdivided into three productive intervals. Cross sections were constructed for correlation of individual layers and identification of localized faulting. The geologic data was input into GeoGraphix software for construction of structure, net pay, production, and gas- and water-oil ratio maps.« less

Petroleum reserves and undiscovered resources in the total petroleum systems of Iraq: Reserve growth and production implications

USGS Publications Warehouse

Verma, M.K.; Ahlbrandt, T.S.; Al-Gailani, M.

2004-01-01

Iraq is one of the world's most petroleum-rich countries and, in the future, it could become one of the main producers. Iraq's petroleum resources are estimated to be 184 billion barrels, which include oil and natural gas reserves, and undiscovered resources. With its proved (or remaining) reserves of 113 billion barrels of oil (BBO) as of January 2003, Iraq ranks second to Saudi Arabia with 259 BBO in the Middle East. Iraq's proved reserves of 110 trillion cubic feet of gas (TCFG) rank tenth in the world. In addition to known reserves, the combined undiscovered hydrocarbon potential for the three Total Petroleum Systems (Paleozoic, Jurassic, and Cretaceous/Tertiary) in Iraq is estimated to range from 14 to 84 BBO (45 BBO at the mean), and 37 to 227 TCFG (120 TCFG at the mean). Additionally, of the 526 known prospective structures, some 370 remain undrilled. Petroleum migration models and associated geological and geochemical studies were used to constrain the undiscovered resource estimates of Iraq. Based on a criterion of recoverable reserves of between 1 and 5 BBO for a giant field, and more than 5 BBO for a super-giant, Iraq has 6 super-giant and 11 giant fields, accounting for 88% of its recoverable reserves, which include proved reserves and cumulative production. Of the 28 producing fields, 22 have recovery factors that range from 15 to 42% with an overall average of less than 30%. The recovery factor can be increased with water injection, improved and enhanced oil recovery methods (IOR and EOR) in various reservoirs, thus potentially increasing Iraq's reserves by an additional 50 to 70 BBO. Reserve growth is a significant factor that has been observed, to some extent, in nearly all Iraqi oil fields. Historically, producing fields have shown an average growth of 1.6 fold (or 60%) in their recoverable reserves over a 20-year period (1981-2001). With periodic assessments of reservoirs, application of available technology, and an upgrading of facilities, increases in reserves are expected in the future.

South Belridge fields, Borderland basin, U. S. , San Joaquin Valley

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D.D.; McPherson, J.G.

1991-03-01

South Belridge is a giant field in the west San Joaquin Valley, Kern County. Cumulative field production is approximately 700 MMBO and 220 BCFG, with remaining recoverable reserves of approximately 500 MMBO. The daily production is nearly 180 MBO from over 6100 active wells. The focus of current field development and production is the shallow Tulare reservoir. Additional probable diatomite reserves have been conservatively estimated at 550 MMBO and 550 BCFG. South Belridge field has two principal reservoir horizons; the Mio-Pliocene Belridge diatomite of the upper Monterey Formation, and the overlying Plio-Pleistocene Tulare Formation. The field lies on the crestmore » of a large southeast-plunging anticline, sub-parallel to the nearby San Andreas fault system. The reservoir trap in both the Tulare and diatomite reservoir horizons is a combination of structure, stratigraphic factors, and tar seals; the presumed source for the oil is the deeper Monterey Formation. The diatomite reservoir produces light oil (20-32{degree} API gravity) form deep-marine diatomite and diatomaceous shales with extremely high porosity (average 60%) and low permeability (average 1 md). In contrast, the shallow ({lt}1000 ft (305 m) deep) overlying Tulare reservoir produces heavy oil (13-14{degree} API gravity) from unconsolidated, arkosic, fluviodeltaic sands of high porosity (average 35%) and permeability (average 3000 md). The depositional model is that of a generally prograding fluviodeltaic system sourced in the nearby basin-margin highlands. More than 6000 closely spaced, shallow wells are the key to steamflood production from hundreds of layered and laterally discontinuous reservoir sands which create laterally and vertically discontinuous reservoir flow units.« less

Enhancement of the sweep efficiency of waterflooding operations by the in-situ microbial population of petroleum reservoirs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, L.R.; Vadie, A.A.; Stephens, J.O.

1995-12-31

Live cores were obtained from five reservoirs using special precautions to prevent contamination by exogenous microorganisms and minimize exposure to oxygen. The depths from which the cores were obtained ranged from 2,705 ft to 6,568 ft. Core plugs were cut radially from live cores, encased in heat-shrink plastic tubes, placed in core holders, and fitted with inlets and outlets. Nutrient additions stimulated the in-situ microbial population to increase, dissolve stratal material, produce gases, and release oil. Reduction in flow through the core plugs was observed in some cases, while in other cases flow was increased, probably due to the dissolutionmore » of carbonates in the formation. A field demonstration of the ability of the in-situ microbial population to increase oil recovery by blocking the more permeable zones of the reservoir is currently underway. This demonstration is being conducted in the North Blowhorn Creek Unit situated in Lamar County, Alabama. Live cores were obtained from a newly drilled well in the field and tested as described above. The field project involves four test patterns each including one injector, four to five producers, and a comparable control injector with its four to five producers. Nutrient injection in the field began November 1994.« less

Reserve growth in oil pools of Alberta: Model and forecast

USGS Publications Warehouse

Verma, M.; Cook, T.

2010-01-01

Reserve growth is recognized as a major component of additions to reserves in most oil provinces around the world, particularly in mature provinces. It takes place as a result of the discovery of new pools/reservoirs and extensions of known pools within existing fields, improved knowledge of reservoirs over time leading to a change in estimates of original oil-in-place, and improvement in recovery factor through the application of new technology, such as enhanced oil recovery methods, horizontal/multilateral drilling, and 4D seismic. A reserve growth study was conducted on oil pools in Alberta, Canada, with the following objectives: 1) evaluate historical oil reserve data in order to assess the potential for future reserve growth; 2) develop reserve growth models/ functions to help forecast hydrocarbon volumes; 3) study reserve growth sensitivity to various parameters (for example, pool size, porosity, and oil gravity); and 4) compare reserve growth in oil pools and fields in Alberta with those from other large petroleum provinces around the world. The reported known recoverable oil exclusive of Athabasca oil sands in Alberta increased from 4.5 billion barrels of oil (BBO) in 1960 to 17 BBO in 2005. Some of the pools that were included in the existing database were excluded from the present study for lack of adequate data. Therefore, the known recoverable oil increased from 4.2 to 13.9 BBO over the period from 1960 through 2005, with new discoveries contributing 3.7 BBO and reserve growth adding 6 BBO. This reserve growth took place mostly in pools with more than 125,000 barrels of known recoverable oil. Pools with light oil accounted for most of the total known oil volume, therefore reflecting the overall pool growth. Smaller pools, in contrast, shrank in their total recoverable volumes over the years. Pools with heavy oil (gravity less than 20o API) make up only a small share (3.8 percent) of the total recoverable oil; they showed a 23-fold growth compared to about 3.5-fold growth in pools with medium oil and 2.2-fold growth in pools with light oil over a fifty-year period. The analysis indicates that pools with high porosity reservoirs (greater than 30 percent porosity) grew more than pools with lower porosity reservoirs which could possibly be attributed to permeability differences between the two types. Reserve growth models for Alberta, Canada, show the growth at field level is almost twice as much as at pool level, possibly because the analysis has evaluated fields with two or more pools with different discovery years. Based on the models, the growth in oil volumes in Alberta pools over the next five-year period (2006-2010) is expected to be about 454 million barrels of oil. Over a twenty-five year period, the cumulative reserve growth in Alberta oil pools has been only 2-fold compared to a 4- to- 5-fold increase in other petroleum producing areas such as Saskatchewan, Volga-Ural, U.S. onshore fields, and U.S. Gulf of Mexico. However, the growth at the field level compares well with that of U.S. onshore fields. In other petroleum provinces, the reserves are reported at field levels rather than at pool levels, the latter basically being the equivalent of individual reservoirs. ?? 2010 by the Canadian Society of Petroleum Geologists.

Total petroleum systems of the Paleozoic and Jurassic, Greater Ghawar Uplift and adjoining provinces of central Saudi Arabia and northern Arabian-Persian Gulf

USGS Publications Warehouse

Pollastro, Richard M.

2003-01-01

Oil of the Arabian Sub-Basin Tuwaiq/Hanifa-Arab TPS is sourced by organic-rich, marine carbonates of the Jurassic Tuwaiq Mountain and Hanifa Formations. These source rocks were deposited in two of three intraplatform basins during the Jurassic and, where thermally mature, have generated a superfamily of oils with distinctive geochemical characteristics. Oils were generated and expelled from these source rocks beginning in the Cretaceous at about 75 Ma. Hydrocarbon production is from 3 cyclic carbonate-rock reservoirs of the Arab Formation that are sealed by overlying anhydrite. Several giant and supergiant fields, including the world's largest oil field at Ghawar, Saudi Arabia, produce mostly from the Arab carbonate-rock reservoirs. Two assessment units are also recognized in the Arabian Sub-Basin Tuwaiq/Hanifa-Arab TPS that are similarly related to structural trap style and presence of underlying Infracambrian salt: (1) an onshore Horst-Block Anticlinal Oil AU, and (2) a mostly offshore Salt-Involved Structural Oil AU. The mean total volume of undiscovered resource for the Arabian Sub-Basin Tuwaiq/Hanifa-Arab TPS is estimated at about 49 billion barrels of oil equivalent (42 billion barrels of oil, 34 trillion feet of gas, and 1.4 billion barrels of natural gas liquids).

Petroleum geology and resources of southeastern Mexico, northern Guatemala, and Belize

USGS Publications Warehouse

Peterson, James A.

1983-01-01

Petroleum deposits in southeastern Mexico and Guatemala occur in two main basinal provinces, the Gulf Coast Tertiary basin area, which includes the Reforma and offshore Campeche Mesozoic fields, and the Peten basin of eastern Chiapas State (Mexico) and Guatemala. Gas production is mainly from Tertiary sandstone reservoirs of Miocene age. Major oil production, in order of importance, is from Cretaceous, Paleocene, and Jurassic carbonate reservoirs in the Reforma and offshore Campeche areas. Several small oil fields have been discovered in Cretaceous carbonate reservoirs in west-central Guatemala, and one major discovery has been reported in northwestern Guatemala. Small- to medium-sized oil accumulations also occur in Miocene sandstone reservoirs on salt structures in the Isthmus Saline basin of western Tabasco State, Mexico. Almost all important production is in salt structure traps or on domes and anticlines that may be related to deep-seated salt structures. Some minor oil production has occurred in Cretaceous carbonate reservoirs in a buried overthrust belt along the west flank of the Veracruz basin. The sedimentary cover of Paleozoic through Tertiary rocks ranges in thickness from about 6,000 m (20,000 ft) to as much as 12,000 m (40,000 ft) or more in most of the region. Paleozoic marine carbonate and clastic rocks 1,000 to 2,000 m (3,300 to 6,500 ft) thick overlie the metamorphic and igneous basement in part of the region; Triassic through Middle Jurassic red beds and evaporite deposits, including halite, apparently are present throughout the region, deposited in part in a Triassic graben system. Upper Jurassic (Oxfordian) through Cretaceous rocks make up the bulk of the Mesozoic regional carbonate bank complex, which dominates most of the area. Tertiary marine and continental clastic rocks, some of deep water origin, 3,000 to 10,000 m (10,000 to 35,000 ft) thick, are present in the coastal plain Tertiary basins. These beds grade eastward into a carbonate sequence that overlies the Mesozoic carbonate complex on the Yucatan platform. During the past 10 years, about 50 large oil fields were discovered in the Reforma and offshore Campeche areas. Oil is produced from intensely microfractured Cretaceous, Paleocene, and Upper Jurassic dolomite reservoirs on blockfaulted salt swells or domes. Most fields are located in the Mesozoic carbonate-bank margin and forebank talus (Tamabra) facies, which passes through the offshore Campeche and onshore Reforma areas. Oil source rocks are believed to be organic-rich shales and shaly carbonate rocks of latest Jurassic and possibly Early Cretaceous age. At least six of the Mesozoic discoveries are giant or supergiant fields. The largest is the Cantarell complex (about 8 billion to 10 billion barrels (BB)) in the offshore Campeche area and the Bermudez complex (about 8 BB) in the Reforma onshore area. Oil columns are unusually large (from 50 m to as much as 1,000 m, or 160 ft to 3,300 ft). Production rates are extremely high, averaging at least 3,000 to 5,000 barrels of oil per day (bo/d); some wells produce more than 20,000 bo/d, particularly in the offshore Campeche area, where 30,000- to 60,000-bo/d wells are reported. Tertiary basin fields produce primarily from Miocene sandstone reservoirs. About 50 of these are oil fields ranging from 1 million barrels (MMB) to 200 MMB in size, located on faulted salt structures in the Isthmus Saline basin. Another 30 are gas or gas-condensate fields of a few billion cubic feet to 3 trillion to 4 trillion cubic feet (Tcf) located on salt structures or probable salt structures in the Macuspana, Comalcalco, Isthmus Saline, and Veracruz basins. Source rocks for the gas are believed to be carbonaceous shales interbedded with the sandstone reservoir bodies. Identified reserves in the southeastern Mexico-Guatemala area, almost all in the Mesozoic fields, are about 53 BB of oil, 3 BB of natural gas liquids, and 65 Tcf of gas. The estimat

Real Time Oil Reservoir Evaluation Using Nanotechnology

NASA Technical Reports Server (NTRS)

Li, Jing (Inventor); Meyyappan, Meyya (Inventor)

2011-01-01

A method and system for evaluating status and response of a mineral-producing field (e.g., oil and/or gas) by monitoring selected chemical and physical properties in or adjacent to a wellsite headspace. Nanotechnology sensors and other sensors are provided for one or more underground (fluid) mineral-producing wellsites to determine presence/absence of each of two or more target molecules in the fluid, relative humidity, temperature and/or fluid pressure adjacent to the wellsite and flow direction and flow velocity for the fluid. A nanosensor measures an electrical parameter value and estimates a corresponding environmental parameter value, such as water content or hydrocarbon content. The system is small enough to be located down-hole in each mineral-producing horizon for the wellsite.

Development of airborne oil thickness measurements.

PubMed

Brown, Carl E; Fingas, Mervin F

2003-01-01

A laboratory sensor has now been developed to measure the absolute thickness of oil on water slicks. This prototype oil slick thickness measurement system is known as the laser-ultrasonic remote sensing of oil thickness (LURSOT) sensor. This laser opto-acoustic sensor is the initial step in the ultimate goal of providing an airborne sensor with the ability to remotely measure oil-on-water slick thickness. The LURSOT sensor employs three lasers to produce and measure the time-of-flight of ultrasonic waves in oil and hence provide a direct measurement of oil slick thickness. The successful application of this technology to the measurement of oil slick thickness will benefit the scientific community as a whole by providing information about the dynamics of oil slick spreading and the spill responder by providing a measurement of the effectiveness of spill countermeasures such as dispersant application and in situ burning. This paper will provide a review of early developments and discuss the current state-of-the-art in the field of oil slick thickness measurement.

Use of Acetate, Propionate, and Butyrate for Reduction of Nitrate and Sulfate and Methanogenesis in Microcosms and Bioreactors Simulating an Oil Reservoir

PubMed Central

Shen, Yin; An, Dongshan; Voordouw, Gerrit

2017-01-01

ABSTRACT Acetate, propionate, and butyrate (volatile fatty acids [VFA]) occur in oil field waters and are frequently used for microbial growth of oil field consortia. We determined the kinetics of use of these VFA components (3 mM each) by an anaerobic oil field consortium in microcosms containing 2 mM sulfate and 0, 4, 6, 8, or 13 mM nitrate. Nitrate was reduced first, with a preference for acetate and propionate. Sulfate reduction then proceeded with propionate (but not butyrate) as the electron donor, whereas the fermentation of butyrate (but not propionate) was associated with methanogenesis. Microbial community analyses indicated that Paracoccus and Thauera (Paracoccus-Thauera), Desulfobulbus, and Syntrophomonas-Methanobacterium were the dominant taxa whose members catalyzed these three processes. Most-probable-number assays showed the presence of up to 107/ml of propionate-oxidizing sulfate-reducing bacteria (SRB) in waters from the Medicine Hat Glauconitic C field. Bioreactors with the same concentrations of sulfate and VFA responded similarly to increasing concentrations of injected nitrate as observed in the microcosms: sulfide formation was prevented by adding approximately 80% of the nitrate dose needed to completely oxidize VFA to CO2 in both. Thus, this work has demonstrated that simple time-dependent observations of the use of acetate, propionate, and butyrate for nitrate reduction, sulfate reduction, and methanogenesis in microcosms are a good proxy for these processes in bioreactors, monitoring of which is more complex. IMPORTANCE Oil field volatile fatty acids acetate, propionate, and butyrate were specifically used for nitrate reduction, sulfate reduction, and methanogenic fermentation. Time-dependent analyses of microcosms served as a good proxy for these processes in a bioreactor, mimicking a sulfide-producing (souring) oil reservoir: 80% of the nitrate dose required to oxidize volatile fatty acids to CO2 was needed to prevent souring in both. Our data also suggest that propionate is a good substrate to enumerate oil field SRB. PMID:28130297

Dynamics of two methanogenic microbiomes incubated in polycyclic aromatic hydrocarbons, naphthenic acids, and oil field produced water.

PubMed

Oko, Bonahis J; Tao, Yu; Stuckey, David C

2017-01-01

Oil field produced water (OFPW) is widely produced in large volumes around the world. Transforming the organic matter in OFPW into bioenergy, such as biomethane, is one promising way to sustainability. However, OFPW is difficult to biologically degrade because it contains complex compounds such as naphthenic acids (NAs), or polycyclic aromatic hydrocarbons (PAHs). Although active microbial communities have been found in many oil reservoirs, little is known about how an exotic microbiome, e.g. the one which originates from municipal wastewater treatment plants, would evolve when incubated with OFPW. In this study, we harvested methanogenic biomass from two sources: a full-scale anaerobic digester (AD) treating oil and gas processing wastewater (named O&G sludge), and from a full-scale AD reactor treating multiple fractions of municipal solid wastes (named MS, short for mixed sludge). Both were incubated in replicate microcosms fed with PAHs, NAs, or OFPW. The results showed that the PAHs, NAs, and OFPW feeds could rapidly alter the methanogenic microbiomes, even after 14 days, while the O&G sludge adapted faster than the mixed sludge in all the incubations. Two rarely reported microorganisms, a hydrogenotrophic methanogen Candidatus methanoregula and a saccharolytic fermenter Kosmotoga , were found to be prevalent in the PAHs and OFPW microcosms, and are likely to play an important role in the syntrophic degradation of PAHs and OFPW, cooperating with methanogens such as Methanoregula, Methanosarcina, or Methanobacterium . The dominant phyla varied in certain patterns during the incubations, depending on the biomass source, feed type, and variation in nutrients. The sludge that originated from the oil and gas processing wastewater treatment (O&G) reactor adapted faster than the one from municipal solid waste reactors, almost certainly because the O&G biomass had been "pre-selected" by the environment. This study reveals the importance of biomass selection for other crude oil-waste-related bioengineering studies, such as bioaugmentation and bioremediation.

76 FR 47009 - Marine Mammals; Incidental Take During Specified Activities

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-03

..., some of these fields include associated satellite oilfields: Sag Delta North, Eider, North Prudhoe Bay... exploration) and CD- 4 (CD South) are in the Colville Delta. The CD-3 drill site is located north of CD-1... oil from the Ivishak formation: Eider produces about 110 barrels per day, and Sag Delta North produces...

Field project to obtain pressure core, wireline log, and production test data for evaluation of CO/sub 2/ flooding potential, Conoco MCA unit well No. 358, Maljamar Field, Lea County, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swift, T.E.; Marlow, R.E.; Wilhelm, M.H.

1981-11-01

This report describes part of the work done to fulfill a contract awarded to Gruy Federal, Inc., by the Department of Energy (DOE) on Feburary 12, 1979. The work includes pressure-coring and associated logging and testing programs to provide data on in-situ oil saturation, porosity and permeability distribution, and other data needed for resource characterization of fields and reservoirs in which CO/sub 2/ injection might have a high probability of success. This report details the second such project. Core porosities agreed well with computed log porosities. Core water saturation and computed log porosities agree fairly well from 3692 to 3712more » feet, poorly from 3712 to 3820 feet and in a general way from 4035 to 4107 feet. Computer log analysis techniques incorporating the a, m, and n values obtained from Core Laboratories analysis did not improve the agreement of log versus core derived water saturations. However, both core and log analysis indicated the ninth zone had the highest residual hydrocarbon saturations and production data confirmed the validity of oil saturation determinations. Residual oil saturation, for the perforated and tested intervals were 259 STB/acre-ft for the interval from 4035 to 4055 feet, and 150 STB/acre-ft for the interval from 3692 to 3718 feet. Nine BOPD was produced from the interval 4035 to 4055 feet and no oil was produced from interval 3692 to 3718 feet, qualitatively confirming the relative oil saturations as calculated. The low oil production in the zone from 4022 to 4055 and the lack of production from 3692 to 3718 feet indicated the zone to be at or near residual waterflood conditions as determined by log analysis. This project demonstrates the usefulness of integrating pressure core, log, and production data to realistically evaluate a reservoir for carbon dioxide flood.« less

Emissions of organic compounds from produced water ponds II: Evaluation of flux chamber measurements with inverse-modeling techniques.

PubMed

Tran, Huy N Q; Lyman, Seth N; Mansfield, Marc L; O'Neil, Trevor; Bowers, Richard L; Smith, Ann P; Keslar, Cara

2018-07-01

In this study, the authors apply two different dispersion models to evaluate flux chamber measurements of emissions of 58 organic compounds, including C2-C11 hydrocarbons and methanol, ethanol, and isopropanol from oil- and gas-produced water ponds in the Uintah Basin. Field measurement campaigns using the flux chamber technique were performed at a limited number of produced water ponds in the basin throughout 2013-2016. Inverse-modeling results showed significantly higher emissions than were measured by the flux chamber. Discrepancies between the two methods vary across hydrocarbon compounds and are largest in alcohols due to their physical chemistries. This finding, in combination with findings in a related study using the WATER9 wastewater emission model, suggests that the flux chamber technique may underestimate organic compound emissions, especially alcohols, due to its limited coverage of the pond area and alteration of environmental conditions, especially wind speed. Comparisons of inverse-model estimations with flux chamber measurements varied significantly with the complexity of pond facilities and geometries. Both model results and flux chamber measurements suggest significant contributions from produced water ponds to total organic compound emission from oil and gas productions in the basin. This research is a component of an extensive study that showed significant amount of hydrocarbon emissions from produced water ponds in the Uintah Basin, Utah. Such findings have important meanings to air quality management agencies in developing control strategies for air pollution in oil and gas fields, especially for the Uintah Basin in which ozone pollutions frequently occurred in winter seasons.

Study of jojoba oil aging by FTIR.

PubMed

Le Dréau, Y; Dupuy, N; Gaydou, V; Joachim, J; Kister, J

2009-05-29

As the jojoba oil was used in cosmetic, pharmaceutical, dietetic food, animal feeding, lubrication, polishing and bio-diesel fields, it was important to study its aging at high temperature by oxidative process. In this work a FT-MIR methodology was developed for monitoring accelerate oxidative degradation of jojoba oils. Principal component analysis (PCA) was used to differentiate various samples according to their origin and obtaining process, and to differentiate oxidative conditions applied on oils. Two spectroscopic indices were calculated to report simply the oxidation phenomenon. Results were confirmed and deepened by multivariate curve resolution-alternative least square method (MCR-ALS). It allowed identifying chemical species produced or degraded during the thermal treatment according to a SIMPLISMA pretreatment.

Adobe unlocks Cherry Canyon, other zones in prolific Barstow unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brewster, J.

1979-08-01

Recent discoveries by Adobe Oil and Gas Corp. in the Barstow unit skirting the Pecos River near Pecos, Texas have extended the Cherry Canyon play approx. 10 miles west in Ward County. In February, Adobe reported an oil discovery, 10 Barstow, drilled between No. 9 and No. 11 (gas wells) in section 34. The well reestablished Cherry Canyon oil production in the Scott field with a potential of 149 bpd of oil and a gor of 1540:1 or gas flow of 230 mcfd. Perforations were from 5827 to 6092 ft. The explanation of the anomaly of an oil well sandwichedmore » between 2 gas wells all producing from the same formation, is that Cherry Canyon consists of lensitic sands, not necessarily connected, that can yield gas and oil in substantially different proportions.« less

Steam-soak performance in south Oman

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rice, S.A.

1991-11-01

With about 2 {times} 10{sup 9} stock-tank m{sup 3} (12.6 {times} 10{sup 9} STB) of medium/heavy oil originally in place (OOIP) in south Oman, considerable scope exists for increasing oil recovery by thermal methods. The viability of thermal recovery in south Oman was tested with a steamflood pilot in the Al Khlata sands of the Marmul field and a 2-year steam-soak project to test the applicability of steam soak in five south Oman oil fields producing heavy oil. This paper describes the performance of the latter project. The wells selected for the test program included a wide range of southmore » Oman reservoir and oil characteristics i.e., the main reservoir drive mechanisms of depletion, solution-gas, and edge- and bottomwater drive, the reservoir sandbody types, and oil viscosities from 80 to 4000 mPa {center dot} s (80 to 4,000 cp). Steam-soak operations were successful, and oil production accelerated significantly, with an average stimulate production rate twice that before stimulation. Acceleration was less marked in wells where reservoir energy is limited or where the primary (cold) water cut is more than 30%. At primary (cold) water cuts {gt}50%, no increase in oil production rate was observed. The process was simulated numerically for several wells, with the results in close agreement with performance. Improved understanding of the process resulting from the simulation allowed the most important factors influencing performance to be identified and aided process optimization in the field test. Two small-scale steam-soak projects currently are being assessed for implementatioimplementation in the early 1990's.« less

EXTENDING THE UNITED STATES NUCLEAR DETERRENCE UMBRELLA TO THE MIDDLE EAST

DTIC Science & Technology

2016-05-01

the oil fields of the Persian Gulf.”27 This policy supported a larger US strategic objective to contain Soviet expansion, and was applied to Saudi... uranium ore concentrate produced by Iran… containment and surveillance of centrifuge rotors and bellows… use of IAEA-approved and certified modern...Caravelli, Jack. Beyond Sand & Oil : The Nuclear Middle East. Santa Barbara, CA: Praeger, 2011. Central Intelligence Agency website. “The World Factbook

Environmental assessment of Buccaneer gas and oil field in the northwestern Gulf of Mexico, 1975-1980. Volume II. Fishes and macro-crustaceans/biofouling communities. Technical memo

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gallaway, B.J.

1980-11-01

Environmental and ecosystem alterations associated with the development and release of contaminants from an active gas and oil field were found to have been primarily related to the presence of the structures and the discharge of produced water. The presence of the structures contributed to turbulent mixing, and allowed for the development of a rich and diverse biofouling community. The resulting artificial reefs were found to serve as points of aggregation for reef fishes as well as species which prey upon them. The produced waters contained low levels of contaminants and were toxic at varying degrees to all organisms tested.more » The effects of the recreational fisheries associated with petroleum platforms in the Gulf on the stocks of red snapper appear to represent a major area of concern.« less

Literature Survey of Crude Oil Properties Relevant to Handling and Fire Safety in Transport.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lord, David; Luketa, Anay; Wocken, Chad

2015-03-01

Several fiery rail accidents in 2013-2015 in the U.S. and Canada carrying crude oil produced from the Bakken region of North Dakota have raised questions at many levels on the safety of transporting this, and other types of crude oil, by rail. Sandia National Laboratories was commissioned by the U.S. Department of Energy to investigate the material properties of crude oils, and in particular the so-called "tight oils" like Bakken that comprise the majority of crude oil rail shipments in the U.S. at the current time. The current report is a literature survey of public sources of information on crudemore » oil properties that have some bearing on the likelihood or severity of combustion events that may occur around spills associated with rail transport. The report also contains background information including a review of the notional "tight oil" field operating environment, as well a basic description of crude oils and potential combustion events in rail transport. This page intentionally blank« less

Verification of the use of completion-location analysis for initial assessment of reservoir heterogeneity

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDowell, R.R.; Avary, K.L.; Hohn, M.E.

1996-12-31

In 1991, a technique (completion-location analysis) was developed for a U.S. DOE-funded study to give a preliminary assessment of field-scale reservoir heterogeneity in two West Virginia oil fields (Granny Creek and Rock Creek). The study`s conclusions regarding heterogeneity agreed with initial predictions. However, as these fields were investigated specifically because they were thought to be heterogeneous, this test of the analysis was biased. In 1995, as part of a proposal to study siliciclastic strandplain reservoirs, the Jacksonburg- Stringtown field in West Virginia, was selected because it met the depositional criterion and was still being actively produced. Completion-location analysis was undertakenmore » on 214 producing oil wells from the field. Analysis indicated that drilling in the fields is clustered into eight time periods (1890-1903, 1904-1911, 1912-1916, 1917-1934, 1935-1953, 1954-1975, 1975-1985, and 1986-1995). Mapping of the locations of wells for each time period indicated that from 1890-1903 approximately 50% of the current geographic extent of the field was defined. Drilling in the periods 1935-1953, 1954-1975, 1975-1985, and 1985-1995 added significantly to the extent of the field - these episodes, especially 1986-1995, represent the discovery of new production. On this basis, a preliminary prediction was made that Jacksonburg-Stringtown field should exhibit a relatively high degree of reservoir heterogeneity. Subsequent discussions with the producer revealed that the reservoir varies considerably in pay thickness and quality across the field, has localized areas with high water injection rates and early water breakthrough, and has areas of anomalously high production. This suggests significant reservoir heterogeneity and appears to verify the utility of completion-location analysis.« less

Verification of the use of completion-location analysis for initial assessment of reservoir heterogeneity

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDowell, R.R.; Avary, K.L.; Hohn, M.E.

1996-01-01

In 1991, a technique (completion-location analysis) was developed for a U.S. DOE-funded study to give a preliminary assessment of field-scale reservoir heterogeneity in two West Virginia oil fields (Granny Creek and Rock Creek). The study's conclusions regarding heterogeneity agreed with initial predictions. However, as these fields were investigated specifically because they were thought to be heterogeneous, this test of the analysis was biased. In 1995, as part of a proposal to study siliciclastic strandplain reservoirs, the Jacksonburg- Stringtown field in West Virginia, was selected because it met the depositional criterion and was still being actively produced. Completion-location analysis was undertakenmore » on 214 producing oil wells from the field. Analysis indicated that drilling in the fields is clustered into eight time periods (1890-1903, 1904-1911, 1912-1916, 1917-1934, 1935-1953, 1954-1975, 1975-1985, and 1986-1995). Mapping of the locations of wells for each time period indicated that from 1890-1903 approximately 50% of the current geographic extent of the field was defined. Drilling in the periods 1935-1953, 1954-1975, 1975-1985, and 1985-1995 added significantly to the extent of the field - these episodes, especially 1986-1995, represent the discovery of new production. On this basis, a preliminary prediction was made that Jacksonburg-Stringtown field should exhibit a relatively high degree of reservoir heterogeneity. Subsequent discussions with the producer revealed that the reservoir varies considerably in pay thickness and quality across the field, has localized areas with high water injection rates and early water breakthrough, and has areas of anomalously high production. This suggests significant reservoir heterogeneity and appears to verify the utility of completion-location analysis.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas C. Chidsey, Jr.

The Paradox Basin of Utah, Colorado, and Arizona contains nearly 100 small oil fields producing from shallow-shelf carbonate buildups or mounds within the Desert Creek zone of the Pennsylvanian (Desmoinesian) Paradox Formation. These fields typically have one to four wells with primary production ranging from 700,000 to 2,000,000 barrels (111,300-318,000 m{sup 3}) of oil per field at a 15 to 20 percent recovery rate. Five fields in southeastern Utah were evaluated for waterflood or carbon-dioxide (CO{sub 2})-miscible flood projects based upon geological characterization and reservoir modeling. Geological characterization on a local scale focused on reservoir heterogeneity, quality, and lateral continuitymore » as well as possible compartmentalization within each of the five project fields. The Desert Creek zone includes three generalized facies belts: (1) open-marine, (2) shallow-shelf and shelf-margin, and (3) intra-shelf, salinity-restricted facies. These deposits have modern analogs near the coasts of the Bahamas, Florida, and Australia, respectively, and outcrop analogs along the San Juan River of southeastern Utah. The analogs display reservoir heterogeneity, flow barriers and baffles, and lithofacies geometry observed in the fields; thus, these properties were incorporated in the reservoir simulation models. Productive carbonate buildups consist of three types: (1) phylloid algal, (2) coralline algal, and (3) bryozoan. Phylloid-algal buildups have a mound-core interval and a supra-mound interval. Hydrocarbons are stratigraphically trapped in porous and permeable lithotypes within the mound-core intervals of the lower part of the buildups and the more heterogeneous supramound intervals. To adequately represent the observed spatial heterogeneities in reservoir properties, the phylloid-algal bafflestones of the mound-core interval and the dolomites of the overlying supra-mound interval were subdivided into ten architecturally distinct lithotypes, each of which exhibits a characteristic set of reservoir properties obtained from outcrop analogs, cores, and geophysical logs. The Anasazi and Runway fields were selected for geostatistical modeling and reservoir compositional simulations. Models and simulations incorporated variations in carbonate lithotypes, porosity, and permeability to accurately predict reservoir responses. History matches tied previous production and reservoir pressure histories so that future reservoir performances could be confidently predicted. The simulation studies showed that despite most of the production being from the mound-core intervals, there were no corresponding decreases in the oil in place in these intervals. This behavior indicates gravity drainage of oil from the supra-mound intervals into the lower mound-core intervals from which the producing wells' major share of production arises. The key to increasing ultimate recovery from these fields (and similar fields in the basin) is to design either waterflood or CO{sub 2}-miscible flood projects capable of forcing oil from high-storage-capacity but low-recovery supra-mound units into the high-recovery mound-core units. Simulation of Anasazi field shows that a CO{sub 2} flood is technically superior to a waterflood and economically feasible. For Anasazi field, an optimized CO{sub 2} flood is predicted to recover a total 4.21 million barrels (0.67 million m3) of oil representing in excess of 89 percent of the original oil in place. For Runway field, the best CO{sub 2} flood is predicted to recover a total of 2.4 million barrels (0.38 million m3) of oil representing 71 percent of the original oil in place. If the CO{sub 2} flood performed as predicted, it is a financially robust process for increasing the reserves in the many small fields in the Paradox Basin. The results can be applied to other fields in the Rocky Mountain region, the Michigan and Illinois Basins, and the Midcontinent.« less

Conversion of crude oil to methane by a microbial consortium enriched from oil reservoir production waters

PubMed Central

Berdugo-Clavijo, Carolina; Gieg, Lisa M.

2014-01-01

The methanogenic biodegradation of crude oil is an important process occurring in petroleum reservoirs and other oil-containing environments such as contaminated aquifers. In this process, syntrophic bacteria degrade hydrocarbon substrates to products such as acetate, and/or H2 and CO2 that are then used by methanogens to produce methane in a thermodynamically dependent manner. We enriched a methanogenic crude oil-degrading consortium from production waters sampled from a low temperature heavy oil reservoir. Alkylsuccinates indicative of fumarate addition to C5 and C6 n-alkanes were identified in the culture (above levels found in controls), corresponding to the detection of an alkyl succinate synthase encoding gene (assA/masA) in the culture. In addition, the enrichment culture was tested for its ability to produce methane from residual oil in a sandstone-packed column system simulating a mature field. Methane production rates of up to 5.8 μmol CH4/g of oil/day were measured in the column system. Amounts of produced methane were in relatively good agreement with hydrocarbon loss showing depletion of more than 50% of saturate and aromatic hydrocarbons. Microbial community analysis revealed that the enrichment culture was dominated by members of the genus Smithella, Methanosaeta, and Methanoculleus. However, a shift in microbial community occurred following incubation of the enrichment in the sandstone columns. Here, Methanobacterium sp. were most abundant, as were bacterial members of the genus Pseudomonas and other known biofilm forming organisms. Our findings show that microorganisms enriched from petroleum reservoir waters can bioconvert crude oil components to methane both planktonically and in sandstone-packed columns as test systems. Further, the results suggest that different organisms may contribute to oil biodegradation within different phases (e.g., planktonic vs. sessile) within a subsurface crude oil reservoir. PMID:24829563

A total petroleum system of the Browse Basin, Australia; Late Jurassic, Early Cretaceous-Mesozoic

USGS Publications Warehouse

Bishop, M.G.

1999-01-01

The Browse Basin Province 3913, offshore northern Australia, contains one important petroleum system, Late Jurassic, Early Cretaceous-Mesozoic. It is comprised of Late Jurassic through Early Cretaceous source rocks deposited in restricted marine environments and various Mesozoic reservoir rocks deposited in deep-water fan to fluvial settings. Jurassic age intraformational shales and claystones and Cretaceous regional claystones seal the reservoirs. Since 1967, when exploration began in this 105,000 km2 area, fewer than 40 wells have been drilled and only one recent oil discovery is considered potentially commercial. Prior to the most recent oil discovery, on the eastern side of the basin, a giant gas field was discovered in 1971, under a modern reef on the west side of the basin. Several additional oil and gas discoveries and shows were made elsewhere. A portion of the Vulcan sub-basin lies within Province 3913 where a small field, confirmed in 1987, produced 18.8 million barrels of oil (MMBO) up to 1995 and has since been shut in.

Russian joint ventures, upstream deals hit fast clip

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-06-29

This paper reports that Russia is stepping up the pace of joint ventures and imports of petroleum technology and hardware. Among the latest action: Polar Lights, a 50-50 venture of Conoco Timan-Pechora Ltd. and Arkhangelskgeologia (AAG), started drilling in the first new-field oil-development project in Russia to include a US partner; The governments of Oman and the Kazakhstan republic signed an agreement covering oil and gas exploration, field development, and production in Kazakhstan; Phibro Energy Inc., Greenwich, Conn., last week reported the sale and delivery of the first full cargo of Russian crude oil produced and exported by a Russian-Americanmore » joint venture; Era Aviation Inc., Anchorage, Alas., is sending two helicopters with crewmen to Russia to help assess the feasibility of oil and gas development off Sakhalin Island; In deals involving Canadian companies, SNC-Lavalin Inc., Montreal, received a contract for initial work on a $350 million (US) modernization of the Volvograd refinery in southern Russia.« less

Streamlining your demulsification program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Svetgoff, J.

1989-09-01

According to this article, demulsification should be viewed as a wide reaching concept that takes into consideration many factors. These include: oil quality, water quality, effect of solids on the demulsification process, consideration of the completeness of the dehydration process, consideration of the most effective use of surface equipment, the use of heat, and cost of the demulsification program. The author discusses how the best demulsification program results in the synergistic use of heat, demulsifier chemicals, electricity, and retention time to provide clean oil and clean water with minimum treating system problems. In addition, these goals should be accomplished atmore » a reasonable cost. However, the amount of heat, chemicals, electricity, or retention time used in a program should not be reduced to the bare minimum. A slight excess of each is necessary to ensure a trouble-free program in most oil field systems. If a producer tries to operate on the ragged edge as far as system resources are concerned, upsets will occur because of the ever-changing nature of oil field systems.« less

Current Soviet exploration plays: Success and potential

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grace, J.D.

1991-03-01

Soviet hydrocarbon exploration in the 1980s took four distinct directions. First was extension exploration and the search for smaller new fields in discrete traps in traditional producing regions, such as the Apsheron Peninsula, North Caucasus, and Volga-Urals. This strategy produced a large number of small discoveries close to established infrastructure. Second was new field exploration in West Siberia in the stratigraphically complex Jurassic and the lower Neocomian sections. Third was expansion of the prolific gas plays in northern West Siberia. Exploratory success in West Siberia has created a backlog of several hundred discoveries awaiting full delineation and development. Most ofmore » these fields are distant from the established oil production center in the Middle Ob region and, therefore, may remain in inventory. Fourth was initial tests of new exploration frontiers, most important, the Paleozoic and Mesozoic plays of the Barents and Kara seas and the subsalt plays of the North Caspian basin. While these plays have yielded very important discoveries, significant technological barriers impede their development. The outlook for Soviet oil exploration in the 1990s is for significant opportunities for discovery of large volumes of oil, but at radically increasing exploration and production costs. In established regions, these costs arise from small field sizes and low well productivities. In frontier regions, exploitation of new fields will require technology not currently available in the USSR. The outlook for gas exploration continues to be very bright, as the onshore northern West Siberia is not fully explored and initial results from the Barents and Kara seas promise more very large gas discoveries.« less

Historical surface deformation near Oildale, California

USGS Publications Warehouse

Castle, Robert O.; Church, Jack P.; Yerkes, Robert F.; Manning, John C.

1983-01-01

Historical surface deformation recognized in the southern San Joaquin Valley and adjacent Sierra Nevada foothills near Oildale, Calif., includes: normal and apparently aseismic dip slip along four faults; subsidence within or adjacent to the Kern Front, Poso Creek, Mount Poso, and Fruitvale oil fields; and uplift of much of the area within and north of the Kern River oil field. As much as 0.34 m of vertical separation has been observed along a 5.2-km segment of the Kern Front fault, the structural barrier separating the Kern Front oil field on the west from the Kern River field to the east. Similar separations of as much as 0.15 m and 0.32 m, respectively, have also been identified along the surface traces of two en echelon faults between the Premier and Enas areas of the Poso Creek oil field and the fault that defines the southeast flank of the Premier area. The measured height changes are based on both unadjusted observed elevations and minimally constrained adjusted elevations developed from repeated control levelings referred to a relatively stable local bench mark; measurement error in the reported vertical movements probably is less than 0.05 m. Differential subsidence of at least 0.31 m (1903-68) and 0.05 m (1926/27/30/31-59) has occurred within the Kern Front and Fruitvale oil fields, respectively; subsidence of as much as 0.33 m (1903-53) and 0.19 m (1931-63) has also been measured along the north edge of the Premier area of the Poso Creek oil field and the south edge of the Main area of the Mount Poso field, respectively. Differential uplift of as much as 0.11 m and 0.13 m occurred within and immediately north of the Kern River oil field between 1903 and 1968, and similar uplift of as much as 0.19 m was measured along the north edge of the Dominion area of the Mount Poso field between 1931 and 1963. Differential subsidence within the Kern Front and Fruitvale oil fields and along the edges of the Poso Creek and Mount Poso fields is attributable to subsurface compaction owing to fluid withdrawal; absence of subsidence within the much larger Kern River field probably is the result of either production from compaction-resistant materials or natural water flooding that has acted to preserve reservoir fluid pressures in the generally shallow producing beds. Contemporary displacements on the Kern Front fault and those along the faults within and adjacent to the Poso Creek oil field are attributable largely or entirely to changes in the subsurface stress regime associated with reservoir compaction; accumulated elastic strain of tectonic derivation conceivably contributed to the development of these displacements. The apparent uplift within and north of the Kern River oil field and along the north edge of the Mount Poso field probably is due in part to compaction of as much as 0.055 m beneath the reference bench mark; most of this apparent uplift, however, is interpreted as an effect of tectonic tilting.

Microbial diversity of an oil-water processing site and its associated oil field: the possible role of microorganisms as information carriers from oil-associated environments.

PubMed

van der Kraan, Geert M; Bruining, Johannes; Lomans, Bart P; van Loosdrecht, Mark C M; Muyzer, Gerard

2010-03-01

The phylogenetic diversity of Bacteria and Archaea in water retrieved from a Dutch oil field and units of the associated oil-water separation site were determined using two culture-independent methods. Denaturing gradient gel electrophoresis of PCR-amplified 16S rRNA gene fragments was used to scan the microbial diversity in (1) the oil-water emulsion produced, (2) two different oil-water separator tanks, (3) a wash tank and (4) a water injector. Longer 16S rRNA gene fragments were amplified, cloned and sequenced to determine the diversity in more detail. One of the questions addressed was whether the detected microorganisms could serve as indicators for the environments from which they were retrieved. It was observed that the community found in the production water resembled those reported previously in oil reservoirs, indicating that these ecosystems harbor specific microbial communities. It was shown that changes, like a decrease in temperature, cause a distinctive shift in these communities. The addition of SO(3)(2-) to the wash tank as ammonium bisulphite, used in the oil industry to scavenge oxygen, resulted in a complete community change, giving rise to an unwanted sulphate-reducing community. The fact that these changes in the community can be linked to changes in their environment might indicate that these tools can be used for the monitoring of changing conditions in oil reservoirs upon, for example, water flooding.

USGS Research on Saline Waters Co-Produced with Energy Resources

USGS Publications Warehouse

,

1997-01-01

The United States energy industry faces the challenge of satisfying our expanding thirst for energy while protecting the environment. This challenge is magnified by the increasing volumes of saline water produced with oil and gas in the Nation's aging petroleum fields. Ultimately, energy-producing companies are responsible for disposing of these waters. USGS research provides basic information, for use by regulators, industry, and the public, about the chemistry of co-produced waters and environmentally acceptable ways of handling them.

77 FR 36519 - Amended Notice of Intent Modifying the Scope of the Environmental Impact Statement for the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-19

... gasify the coal and petcoke to produce synthesis gas (syngas), which would then be purified to produce a... pipeline to the adjacent Elk Hills Oil Field (owned and operated by Occidental of Elk Hills, Inc. (OEHI..., Gas and Geothermal Resources (DOGGR). Pursuant to California law and a grant of primacy from the...

Monitoring of Land Deformation Due to Oil Production by InSAR Time Series Analysis Using PALSAR Data in Bolivarian Republic of Venezuela

NASA Astrophysics Data System (ADS)

Deguchi, Tomonori; Narita, Tatsuhiko

2015-05-01

The target area of this study is the Maracaibo sedimentary basin located in the western part of Bolivarian Republic of Venezuela. The full-scale exploration and development for oil resources in Venezuela which was the greatest oil-producing country in South America had begun at the Maracaibo sedimentary basin in the 1910s, and it was a center of the oil product in Venezuela until the 1980s. But, in most of oil fields in the Maracaibo sedimentary basin, there is concern over the drain on recoverable reserves due to deterioration, and the production amount of petroleum in Venezuela has been diminishing these days. Leveling and GPS surveying were carried out in the past, and they revealed that the large-scale subsidence phenomenon of which cumulative subsidence amount was approximately 5 meter had occurred. The authors applied the vertical displacement measurement by InSAR time series analysis using PALSAR data obtained in the Fine-beam and ScanSAR observation mode. As a result, it could be confirmed clear ground deformation in the surrounding of three oil fields (Tia Juana, Lagunillas and Bachaquero) and easily recognized that the areas of phase anomalies detected by this analysis had expanded and the number of interference fringes had increased over time. The annual velocity of vertical ground surface displacement measured by InSAR time series analysis was -51 mm per year, -103 mm per year and -58 mm per year in Tia Juana, Lagunillas and Bachaquero oil field respectively. The tendency that an earth surface shifted towards the center of phase anomalies was detected from the result of the horizontal ground change measurement. It was interpreted from Google Earth and Landsat images that oil-related facilities (mainly bowling stations) were built intensively over the areas where phase anomalies were detected. Therefore, it was inferred that there was a high association between the operation activity of the oil field and ground deformation. In addition, the deterioration is remarkable in the oil fields of the Maracaibo basin and oil production volume has been declining, on the other hand the spatial volume of the ground surface deformation also showed a clear decreasing trend.

Cleanup/stimulation of a horizontal wellbore using propellants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rougeot, J.E.; Lauterbach, K.A.

1993-01-01

This report documents the stimulation/cleanup of a horizontal well bore (Wilson 25) using propellants. The Wilson 25 is a Bartlesville Sand well located in the Flatrock Field, Osage County, Oklahoma. The Wilson 25 was drilled to determine if horizontal drilling could be used as a means to economically recover primary oil that had been left in place in a mostly abandoned oil field because of the adverse effects of water coning. Pump testing of the Wilson 25 horizontal well bore before cleanup or stimulation produced 6 barrels of oil and .84 barrels of water per day. The high percentage ofmore » daily oil production to total daily fluid production indicated that the horizontal well bore had accessed potentially economical oil reserves if the fluid production rate could be increased by performing a cleanup/stimulation treatment. Propellants were selected as an inexpensive means to stimulate and cleanup the near well bore area in a uniform manner. The ignition of a propellant creates a large volume of gas which penetrates the formation, creating numerous short cracks through which hydrocarbons can travel into the well bore. More conventional stimulation/cleanup techniques were either significantly more expensive, less likely to treat uniformly, or could not be confined to the near well bore area. Three different propellant torpedo designs were tested with a total of 304' of horizontal well bore being shot and producible. The initial test shot caused 400' of the horizontal well bore to become plugged off, and subsequently it could not be production tested. The second and third test shots were production tested, with the oil production being increased 458% and 349%, respectively, on a per foot basis. The Wilson 25 results indicate that a propellant shot treatment is an economically viable means to cleanup/stimulate a horizontal well bore.« less

Revitalizing a mature oil play: Strategies for finding and producing oil in Frio Fluvial-Deltaic Sandstone reservoirs of South Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knox, P.R.; Holtz, M.H.; McRae, L.E.

Domestic fluvial-dominated deltaic (FDD) reservoirs contain more than 30 Billion barrels (Bbbl) of remaining oil, more than any other type of reservoir, approximately one-third of which is in danger of permanent loss through premature field abandonments. The U.S. Department of Energy has placed its highest priority on increasing near-term recovery from FDD reservoirs in order to prevent abandonment of this important strategic resource. To aid in this effort, the Bureau of Economic Geology, The University of Texas at Austin, began a 46-month project in October, 1992, to develop and demonstrate advanced methods of reservoir characterization that would more accurately locatemore » remaining volumes of mobile oil that could then be recovered by recompleting existing wells or drilling geologically targeted infill. wells. Reservoirs in two fields within the Frio Fluvial-Deltaic Sandstone (Vicksburg Fault Zone) oil play of South Texas, a mature play which still contains 1.6 Bbbl of mobile oil after producing 1 Bbbl over four decades, were selected as laboratories for developing and testing reservoir characterization techniques. Advanced methods in geology, geophysics, petrophysics, and engineering were integrated to (1) identify probable reservoir architecture and heterogeneity, (2) determine past fluid-flow history, (3) integrate fluid-flow history with reservoir architecture to identify untapped, incompletely drained, and new pool compartments, and (4) identify specific opportunities for near-term reserve growth. To facilitate the success of operators in applying these methods in the Frio play, geologic and reservoir engineering characteristics of all major reservoirs in the play were documented and statistically analyzed. A quantitative quick-look methodology was developed to prioritize reservoirs in terms of reserve-growth potential.« less

Major Oil Plays in Utah and Vicinity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas C. Chidsey; Craig D. Morgan; Kevin McClure

2003-12-31

Utah oil fields have produced over 1.2 billion barrels (191 million m{sup 3}). However, the 13.7 million barrels (2.2 million m{sup 3}) of production in 2002 was the lowest level in over 40 years and continued the steady decline that began in the mid-1980s. The Utah Geological Survey believes this trend can be reversed by providing play portfolios for the major oil-producing provinces (Paradox Basin, Uinta Basin, and thrust belt) in Utah and adjacent areas in Colorado and Wyoming. Oil plays are geographic areas with petroleum potential caused by favorable combinations of source rock, migration paths, reservoir rock characteristics, andmore » other factors. The play portfolios will include: descriptions and maps of the major oil plays by reservoir; production and reservoir data; case-study field evaluations; locations of major oil pipelines; identification and discussion of land-use constraints; descriptions of reservoir outcrop analogs; and summaries of the state-of-the-art drilling, completion, and secondary/tertiary techniques for each play. This report covers research activities for the sixth quarter of the project (October 1 through December 31, 2003). This work included describing outcrop analogs for the Jurassic Twin Creek Limestone and Mississippian Leadville Limestone, major oil producers in the thrust belt and Paradox Basin, respectively, and analyzing best practices used in the southern Green River Formation play of the Uinta Basin. Production-scale outcrop analogs provide an excellent view of reservoir petrophysics, facies characteristics, and boundaries contributing to the overall heterogeneity of reservoir rocks. They can be used as a ''template'' for evaluation of data from conventional core, geophysical and petrophysical logs, and seismic surveys. In the Utah/Wyoming thrust belt province, the Jurassic Twin Creek Limestone produces from subsidiary closures along major ramp anticlines where the low-porosity limestone beds are extensively fractured and sealed by overlying argillaceous and non-fractured units. The best outcrop analogs for Twin Creek reservoirs are found at Devils Slide and near the town of Peoa, Utah, where fractures in dense, homogeneous non-porous limestone beds are in contact with the basal siltstone units (containing sealed fractures) of the overlying units. The shallow marine, Mississippian Leadville Limestone is a major oil and gas reservoir in the Paradox Basin of Utah and Colorado. Hydrocarbons are produced from basement-involved, northwest-trending structural traps with closure on both anticlines and faults. Excellent outcrops of Leadville-equivalent rocks are found along the south flank of the Uinta Mountains, Utah. For example, like the Leadville, the Mississippian Madison Limestone contains zones of solution breccia, fractures, and facies variations. When combined with subsurface geological and production data, these outcrop analogs can improve (1) development drilling and production strategies such as horizontal drilling, (2) reservoir-simulation models, (3) reserve calculations, and (4) design and implementation of secondary/tertiary oil recovery programs and other best practices used in the oil fields of Utah and vicinity. In the southern Green River Formation play of the Uinta Basin, optimal drilling, development, and production practices consist of: (1) owning drilling rigs and frac holding tanks; (2) perforating sandstone beds with more than 8 percent neutron porosity and stimulate with separate fracture treatments; (3) placing completed wells on primary production using artificial lift; (4) converting wells relatively soon to secondary waterflooding maintaining reservoir pressure above the bubble point to maximize oil recovery; (5) developing waterflood units using an alternating injector--producer pattern on 40-acre (16-ha) spacing; and (6) recompleting producing wells by perforating all beds that are productive in the waterflood unit. As part of technology transfer activities during this quarter, an abstract describing outcrop reservoir analogs was accepted by the American Association of Petroleum Geologists, for presentation at the 2004 annual meeting in Dallas, Texas. Another abstract was submitted for consideration on basin-wide correlation of Green River Formation plays and subplays in the Uinta Basin in Utah. The project home page was updated on the Utah Geological Survey Internet web site.« less

Simulations of the origin of fluid pressure, fracture gen­ eration, and the movement of fluids in the Uinta Basin, Utah

USGS Publications Warehouse

Bredehoeft, J.D.; Wesley, J.B.; Fouch, T.D.

1994-01-01

The Altamont oil field in the deep Uinta basin is known to have reservoir fluid pressures that approach lithostatic. One explanation for this high pore-fluid pressure is the generation of oil from kerogen in the Green River oil shale at depth. A three-dimensional simulation of flow in the basin was done to test this hypothesis.In the flow simulation, oil generation is included as a fluid source. The kinetics of oil generation from oil shale is a function of temperature. The temperature is controlled by (1) the depth of sediment burial and (2) the geothermal gradient.Using this conceptual model, the pressure buildup results from the trade-off between the rate of oil generation and the flow away from the source volume. The pressure increase depends primarily on (1) the rate of the oil-generation reaction and (2) the permeability of the reservoir rocks. A sensitivity analysis was performed in which both of these parameters were systematically varied. The reservoir permeability must be lower than most of the observed data for the pressure to build up to near lithostatic.The results of the simulations indicated that once oil generation was initiated, the pore pressure built up rapidly to near lithostatic. We simulated hydrofractures in that part of the system in which the pressures approach lithostatic by increasing both the horizontal and the vertical permeability by an order of magnitude. Because the simulated hydrofractures were produced by the high pore pressure, they were restricted to the Altamont field. A new flow system was established in the vicinity of the reservoir; the maximum pore pressure was limited by the least principal stress. Fluids moved vertically up and down and laterally outward away from the source of oil generation. The analysis indicated that, assuming that one is willing to accept the low values of permeability, oil generati n can account for the observed high pressures at Altamont field.

Microbial enhanced oil recovery: Entering the log phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bryant, R.S.

1995-12-31

Microbial enhanced oil recovery (MEOR) technology has advanced internationally since 1980 from a laboratory-based evaluation of microbial processes to field applications. In order to adequately support the decline in oil production in certain areas, research on cost-effective technologies such as microbial enhanced oil recovery processes must focus on both near-term and long-term applications. Many marginal wells are desperately in need of an inexpensive improved oil recovery technology today that can assist producers in order to prevent their abandonment. Microbial enhanced waterflooding technology has also been shown to be an economically feasible technology in the United States. Complementary environmental research andmore » development will also be required to address any potential environmental impacts of microbial processes. In 1995 at this conference, the goal is to further document and promote microbial processes for improved oil recovery and related technology for solving environmental problems.« less

Emulsifying conditions and processing parameters optimisation of kenaf seed oil-in-water nanoemulsions stabilised by ternary emulsifier mixtures.

PubMed

Cheong, Ai M; Tan, Chin P; Nyam, Kar L

2018-01-01

Kenaf ( Hibiscus cannabinus L.) seed oil has been proven for its multi-pharmacological benefits; however, its poor water solubility and stability have limited its industrial applications. This study was aimed to further improve the stability of pre-developed kenaf seed oil-in-water nanoemulsions by using food-grade ternary emulsifiers. The effects of emulsifier concentration (1, 5, 10, 15% w/w), homogenisation pressure (16,000, 22,000, 28,000 psi), and homogenisation cycles (three, four, five cycles) were studied to produce high stability of kenaf seed oil-in-water nanoemulsions using high pressure homogeniser. Generally, results showed that the emulsifier concentration and homogenisation conditions had great effect ( p < 0.05) on the particle sizes, polydispersity index and hence the physical stability of nanoemulsions. Homogenisation parameters at 28,000 psi for three cycles produced the most stable homogeneous nanoemulsions that were below 130 nm, below 0.16, and above -40 mV of particle size, polydispersity index, and zeta potential, respectively. Field emission scanning electron microscopy micrograph showed that the optimised nanoemulsions had a good distribution within nano-range. The optimised nanoemulsions were proved to be physically stable for up to six weeks of storage at room temperature. The results from this study also provided valuable information in producing stable kenaf seed oil nanoemulsions for the future application in food and nutraceutical industries.

Demulsification key to production efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Svetgoff, J.A.

1988-08-01

Concern over the declining profitability in the petroleum industry has generated renewed interest in reducing costs and enhancing profits. This article discusses one are often overlooked when trying to optimize profits, the process of demulsification. Resolving crude oil emulsions is a costly operational problem in most producing fields. Because it is one of the least understood facets of the petroleum industry, the costs associated with demulsification are often excessive. Although there are many similarities, desalting is a separate subject from demulsification. The removal of produced water from crude oil is the primary goal of demulsification, while minimizing the salt contentmore » in crude oil is the object of a desalting program. Understanding demulsification and desalting concepts is important to design engineers. The author discusses how this knowledge enables them to design systems that minimize operating costs while meeting present, as well as future, needs.« less

Alkylphenol metabolites in fish bile as biomarkers of exposure to offshore oil industry produced water in feral fish.

PubMed

Beyer, Jonny; Sundt, Rolf C; Sanni, Steinar; Sydnes, Magne O; Jonsson, Grete

2011-01-01

The measurement of low-concentration alkylphenol (AP) exposure in fish is relevant in connection with monitoring and risk assessment of offshore oil industry produced water (PW) discharges. Detection of AP markers in fish bile offers significantly greater sensitivity than detection of AP in tissues such as liver. Recent studies revealed that gas chromatography-mass spectrometry in electron ionization mode (GC-EI-MS) enabled a selective and sensitive analytical detection of PW AP in mixtures with unknown composition. A procedure consisting of enzymatic deconjugation of metabolites in fish bile followed by derivatization with bis(trimethylsilyl)trifluoroacetamide and then separation and quantification of derivatized AP using GC-EI-MS is presented. The use of this procedure as a possible recommended approach for assessment and biomonitoring of AP contamination in fish populations living down-current from offshore oil production fields is presented.

Development of fuel oil management system software: Phase 1, Tank management module. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lange, H.B.; Baker, J.P.; Allen, D.

1992-01-01

The Fuel Oil Management System (FOMS) is a micro-computer based software system being developed to assist electric utilities that use residual fuel oils with oil purchase and end-use decisions. The Tank Management Module (TMM) is the first FOMS module to be produced. TMM enables the user to follow the mixing status of oils contained in a number of oil storage tanks. The software contains a computational model of residual fuel oil mixing which addresses mixing that occurs as one oil is added to another in a storage tank and also purposeful mixing of the tank by propellers, recirculation or convection.Themore » model also addresses the potential for sludge formation due to incompatibility of oils being mixed. Part 1 of the report presents a technical description of the mixing model and a description of its development. Steps followed in developing the mixing model included: (1) definition of ranges of oil properties and tank design factors used by utilities; (2) review and adaption of prior applicable work; (3) laboratory development; and (4) field verification. Also, a brief laboratory program was devoted to exploring the suitability of suggested methods for predicting viscosities, flash points and pour points of oil mixtures. Part 2 of the report presents a functional description of the TMM software and a description of its development. The software development program consisted of the following steps: (1) on-site interviews at utilities to prioritize needs and characterize user environments; (2) construction of the user interface; and (3) field testing the software.« less

Development of fuel oil management system software: Phase 1, Tank management module

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lange, H.B.; Baker, J.P.; Allen, D.

1992-01-01

The Fuel Oil Management System (FOMS) is a micro-computer based software system being developed to assist electric utilities that use residual fuel oils with oil purchase and end-use decisions. The Tank Management Module (TMM) is the first FOMS module to be produced. TMM enables the user to follow the mixing status of oils contained in a number of oil storage tanks. The software contains a computational model of residual fuel oil mixing which addresses mixing that occurs as one oil is added to another in a storage tank and also purposeful mixing of the tank by propellers, recirculation or convection.Themore » model also addresses the potential for sludge formation due to incompatibility of oils being mixed. Part 1 of the report presents a technical description of the mixing model and a description of its development. Steps followed in developing the mixing model included: (1) definition of ranges of oil properties and tank design factors used by utilities; (2) review and adaption of prior applicable work; (3) laboratory development; and (4) field verification. Also, a brief laboratory program was devoted to exploring the suitability of suggested methods for predicting viscosities, flash points and pour points of oil mixtures. Part 2 of the report presents a functional description of the TMM software and a description of its development. The software development program consisted of the following steps: (1) on-site interviews at utilities to prioritize needs and characterize user environments; (2) construction of the user interface; and (3) field testing the software.« less

Effects of saline-wastewater injection on water quality in the Altamont-Bluebell oil and gas field, Duchesne County, Utah, 1990-2005

USGS Publications Warehouse

Steiger, Judy I.

2007-01-01

The Altamont-Bluebell oil and gas field in the Uinta Basin in northeastern Utah has been an important oil and natural gas production area since the 1950s. Saline water is produced along with oil during the oil-well drilling and pumping process. The saline wastewater is disposed of by injection into wells completed in the Duchesne River Formation, Uinta Formation, and other underlying formations. There are concerns that the injected saline wastewater could migrate into the upper part of the Duchesne River and Uinta Formations and surficial deposits that are used for drinking-water supply and degrade the quality of the drinking water. The U.S. Geological Survey, in cooperation with the Utah Department of Natural Resources, Division of Oil, Gas, and Mining, began a program in 1990 to monitor water quality in five wells in the Altamont-Bluebell oil and gas field. By 1996, water-quality samples had been collected from 20 wells. Ten of the 20 wells were sampled yearly during 1996-2005 and analyzed for bromide, chloride, and stable isotopes. Comparison of major chemical constituents, bromide-to-chloride ratios, trend analysis, and isotope ratios were used to assess if saline wastewater is migrating into parts of the formation that are developed for drinking-water supplies. Results of four different analyses all indicate that saline wastewater injected into the lower part of the Duchesne River and Uinta Formations and underlying formations is not migrating upward into the upper parts of the formations that are used for drinking-water supplies.

INCREASING HEAVY OIL RESERVES IN THE WILMINGTON OIL FIELD THROUGH ADVANCED RESERVOIR CHARACTERIZATION AND THERMAL PRODUCTION TECHNOLOGIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unknown

2001-08-08

The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California, through the testing and application of advanced reservoir characterization and thermal production technologies. The hope is that successful application of these technologies will result in their implementation throughout the Wilmington Field and, through technology transfer, will be extended to increase the recoverable oil reserves in other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block II-A (Tar II-A) has been relatively inefficient because of several producibility problems which aremore » common in SBC reservoirs: inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. A suite of advanced reservoir characterization and thermal production technologies are being applied during the project to improve oil recovery and reduce operating costs, including: (1) Development of three-dimensional (3-D) deterministic and stochastic reservoir simulation models--thermal or otherwise--to aid in reservoir management of the steamflood and post-steamflood phases and subsequent development work. (2) Development of computerized 3-D visualizations of the geologic and reservoir simulation models to aid reservoir surveillance and operations. (3) Perform detailed studies of the geochemical interactions between the steam and the formation rock and fluids. (4) Testing and proposed application of a novel alkaline-steam well completion technique for the containment of the unconsolidated formation sands and control of fluid entry and injection profiles. (5) Installation of a 2100 ft, 14 inch insulated, steam line beneath a harbor channel to supply steam to an island location. (6) Testing and proposed application of thermal recovery technologies to increase oil production and reserves: (a) Performing pilot tests of cyclic steam injection and production on new horizontal wells. (b) Performing pilot tests of hot water-alternating-steam (WAS) drive in the existing steam drive area to improve thermal efficiency. (7) Perform a pilot steamflood with the four horizontal injectors and producers using a pseudo steam-assisted gravity-drainage (SAGD) process. (8) Advanced reservoir management, through computer-aided access to production and geologic data to integrate reservoir characterization, engineering, monitoring and evaluation.« less

Climate impacts of oil extraction increase significantly with oilfield age

NASA Astrophysics Data System (ADS)

Masnadi, Mohammad S.; Brandt, Adam R.

2017-08-01

Record-breaking temperatures have induced governments to implement targets for reducing future greenhouse gas (GHG) emissions. Use of oil products contributes ~35% of global GHG emissions, and the oil industry itself consumes 3-4% of global primary energy. Because oil resources are becoming increasingly heterogeneous, requiring different extraction and processing methods, GHG studies should evaluate oil sources using detailed project-specific data. Unfortunately, prior oil-sector GHG analysis has largely neglected the fact that the energy intensity of producing oil can change significantly over the life of a particular oil project. Here we use decades-long time-series data from twenty-five globally significant oil fields (>1 billion barrels ultimate recovery) to model GHG emissions from oil production as a function of time. We find that volumetric oil production declines with depletion, but this depletion is accompanied by significant growth--in some cases over tenfold--in per-MJ GHG emissions. Depletion requires increased energy expenditures in drilling, oil recovery, and oil processing. Using probabilistic simulation, we derive a relationship for estimating GHG increases over time, showing an expected doubling in average emissions over 25 years. These trends have implications for long-term emissions and climate modelling, as well as for climate policy.

Reserve growth of the world's giant oil fields

USGS Publications Warehouse

Klett, T.R.; Schmoker, J.W.

2005-01-01

Analysis of estimated total recoverable oil volume (field size) of 186 well-known giant oil fields of the world (>0.5 billion bbl of oil, discovered prior to 1981), exclusive of the United States and Canada, demonstrates general increases in field sizes through time. Field sizes were analyzed as a group and within subgroups of the Organization of Petroleum Exporting Countries (OPEC) and non-OPEC countries. From 1981 through 1996, the estimated volume of oil in the 186 fields for which adequate data were available increased from 617 billion to 777 billion bbl of oil (26%). Processes other than new field discoveries added an estimated 160 billion bbl of oil to known reserves in this subset of the world's oil fields. Although methods for estimating field sizes vary among countries, estimated sizes of the giant oil fields of the world increased, probably for many of the same reasons that estimated sizes of oil fields in the United States increased over the same time period. Estimated volumes in OPEC fields increased from a total of 550 billion to 668 billion bbl of oil and volumes in non-OPEC fields increased from 67 billion to 109 billion bbl of oil. In terms of percent change, non-OPEC field sizes increased more than OPEC field sizes (63% versus 22%). The changes in estimated total recoverable oil volumes that occurred within three 5-year increments between 1981 and 1996 were all positive. Between 1981 and 1986, the increase in estimated total recoverable oil volume within the 186 giant oil fields was 11 billion bbl of oil; between 1986 and 1991, the increase was 120 billion bbl of oil; and between 1991 and 1996, the increase was 29 billion bbl of oil. Fields in both OPEC and non-OPEC countries followed trends of substantial reserve growth.

Heavy oil recovery process: Conceptual engineering of a downhole methanator and preliminary estimate of facilities cost for application to North Slope Alaska

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gondouin, M.

1991-10-31

The West Sak (Upper Cretaceous) sands, overlaying the Kuparuk field, would rank among the largest known oil fields in the US, but technical difficulties have so far prevented its commercial exploitation. Steam injection is the most successful and the most commonly-used method of heavy oil recovery, but its application to the West Sak presents major problems. Such difficulties may be overcome by using a novel approach, in which steam is generated downhole in a catalytic Methanator, from Syngas made at the surface from endothermic reactions (Table 1). The Methanator effluent, containing steam and soluble gases resulting from exothermic reactions (Tablemore » 1), is cyclically injected into the reservoir by means of a horizontal drainhole while hot produced fluids flow form a second drainhole into a central production tubing. The downhole reactor feed and BFW flow downward to two concentric tubings. The large-diameter casing required to house the downhole reactor assembly is filled above it with Arctic Pack mud, or crude oil, to further reduce heat leaks. A quantitative analysis of this production scheme for the West Sak required a preliminary engineering of the downhole and surface facilities and a tentative forecast of well production rates. The results, based on published information on the West Sak, have been used to estimate the cost of these facilities, per daily barrel of oil produced. A preliminary economic analysis and conclusions are presented together with an outline of future work. Economic and regulatory conditions which would make this approach viable are discussed. 28 figs.« less

Application of thematic mapper imagery to oil exploration in Austin Chalk, central Gulf Coast basin, Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reid, W.M.

1988-02-01

One of the newest major oil plays in the Gulf Coast basin, the Austin Chalk reportedly produces in three belts: an updip belt, where production is from fractured chalk in structurally high positions along faults above 7000 ft; a shallow downdip belt, where the chalk is uniformly saturated with oil from 7000 to 9000 ft; and a deeper downdip belt saturated with gas and condensate below 9000 ft. The updip fields usually occur on the southeastern, upthrown side of the Luling, Mexia, and Charlotte fault zones. Production is from fractures that connect the relatively sparse matrix pores with more permeablemore » fracture systems. The fractures resulted from regional extensional stress during the opening of the Gulf Coast basin on the divergent margin of the North American plate during the Laramide orogeny. The fractures are more common in the more brittle chalk than in the overlying Navarro and underlying Eagle Ford shales, which are less brittle. The oil in the updip traps in the chalk may have been generated in place downdip, and migrated updip along the extension fractures into the updip traps during or after the Laramide orogeny. A fairway of previously unmapped updip faults and drag folds has been mapped using Thematic Mapper imagery and seismic, structural, and resistivity maps near the Nixon field, Burleson County, Texas. This fairway, prospective for oil from the Austin Chalk, contains wells reported to produce from the Austin Chalk which lie along lineaments and linear features on the Thematic Mapper imagery and faults in the seismic and structure maps.« less

Morphological Variation and Recovery Mechanism of Residual Crude Oil by Biosurfactant from Indigenous Bacteria: Macro- and Pore-Scale Experimental Investigations.

PubMed

Song, Zhi-Yong; Han, Hong-Yan; Zhu, Wei-Yao

2015-06-01

Microbial enhanced oil recovery (MEOR) is being used more widely, and the biological contributions involved in MEOR need to be identified and quantified for the improvement of field applications. Owing to the excellent interfacial activity and the wide distribution of producing strains in oil reservoirs, lipopeptides have proved to be an essential part of the complex mechanisms in MEOR. In this study, crude lipopeptides were produced by a strain isolated from an indigenous community in an oil reservoir. It was found that crude lipopeptides can effectively reduce the IFT (interfacial tension) to 10(-1)~10(-2) mN/m under high salinity without forming stable emulsions, and the wettability of natural sandstone can be enhanced (Amott index, from 0.36 to 0.48). The results of core flooding experiments indicate that an additional 5.2% of original oil in place can be recovered with a 9.5% reduction of injection pressure. After the shut-in period, the wettability of the core, the reduction of injection pressure, and the oil recovery can be improved to 0.63, 16.2% and 9.6%, respectively. In the microscopic flooding experiments, the crude oil in membrane, cluster, and throat states contribute nearly 90% in total of the additional oil recovery, and the recovery of membranestate oil was significantly enhanced by 93.3% after shut in. Based on the results in macro and pore scale, the IFT reduction and the wettability alteration are considered primary contributors to oil recovery, while the latter was more dominant after one shut-in period.

More steam for Kern River

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rintoul, B.

1973-02-01

While production generally is declining elsewhere in California, the Kern River field continues to post gains. The field last year produced at an all-time high for the second year in a row, putting out at least 1.5 million bbl more than in its previous peak year. There is every reason to believe that gains will continue through this year. Steam is in the factor that underlies Kern River's resurgence, and Getty Oil Co., the field's premier steamer, recently added to its already imposing array of steam-generating equipment a pair of large boilers, each capable of generating 240 million btus permore » hr. Along with expansion of the steaming effort the company also expanded its water-treating facilities, making sure there will be plenty of feed water to fuel the steam generators at work in the field. The new boilers are being used to furnish steam to 136 wells in a steam displacement project. The purpose of going to a larger generator has been to gain higher efficiency. The components that have made Getty Oil the leading steamer at Kern River and the field, in turn, the world capital for oil-field steam operations include shallow wells, steam generators and--since 1969--a computer. The entire project is described in detail.« less

The New Albany shale in Illinois: Emerging play or prolific source

USGS Publications Warehouse

Crockett, Joan; Morse, David E.

2010-01-01

The New Albany shale (Upper Devonian) in the Illinois basin is the primary hydrocarbon source rock for the basins nearly 4 billion bbl of oil production to date. The gas play is well-established in Indiana and Western Kentucky. One in-situ oil producing well was reported in a multiply competed well in the New Albany at Johnsonville field in Wayne County, Illinois. The Illinois gas and oil wells at Russellville, in Lawrence County are closely associated with the 0.6% reflectance contour, which suggests a higher level of thermal maturity in this area. Today, only one field, Russellville in eastern Lawrence County has established commercial production in the Ness Albany in Illinois. Two wildcat wells with gas shows were drilled in recent years in southern Saline County, where the New Albany is relatively deeply buried and close to faults associated with the Fluorspar District.

Growth in conventional fields in high-cost areas: a case study

USGS Publications Warehouse

Attanasi, E.D.

2000-01-01

Exploration managers commonly base future drilling decisions on past experience in an area. To do this well, they should consider both discovered and undiscovered resources to characterize total future potential. Discovery-size estimates should be adjusted to account for future field growth; otherwise, the relative efficiency of recent exploration will be undervalued. This study models and projects field growth for pre-1997 discoveries in the U.S. Federal Gulf of Mexico (GOM) Outer Continental Shelf (OCS). Projected additions to reserves for these fields from field growth through 2020 are 5.2 billion bbl of oil and 46 Tcfg. Projections include growth associated with sizable new oil discoveries in deepwater areas and initial reserve additions from new subsalt plays discovered through 1996. This article focuses on the U.S. GOM because it has produced longer than other worldwide offshore areas. Its field-growth profile may be prototypical of other offshore provinces such as the North Sea, Scotian Shelf and deepwater Angola, as well as high-cost onshore areas.

The Kuwait oil fires as seen by Landsat

NASA Astrophysics Data System (ADS)

Cahalan, Robert F.

1992-09-01

A mosaic of two Landsat thematic mapper images acquired May 30, 1991, reveals a dark smoke plume 30-60 km wide extending hundreds of kilometers south of Kuwait City along the Persian Gulf. Smoke coming from the Raudhatain and Sabriyah oil fields blew across the Gulf of Kuwait and over Kuwait City, joined with smoke from the Greater Burgan and Minagish fields, and continued southward over smaller villages and regions of desert agriculture consisting of hundreds of axially irrigated fields in both Kuwait and Saudi Arabia. One agricultural region in Kuwait was completely obscured by the smoke. The light colored limestone gravel and sand surface was darkened by oil lakes near the wells, and by oil drizzling out of the plume downwind of the wells. Most fires produced either a light or dark plume, and the separate plumes mixed to form a combined plume much darker than the land surface, but slightly more reflective than the Gulf waters. A few of the hottest fires had no visible plume, and are presumably associated with methane combustion. The last of the Kuwait fires was reportedly extinguished in November of 1991. Continued monitoring is needed to assess the impact of emissions from both burning and nonburning oil wells on the region's climate, as well as on the agriculture, fishing, and other activities essential to life in the region.

The Kuwait oil fires as seen by Landsat

NASA Technical Reports Server (NTRS)

Cahalan, Robert F.

1992-01-01

A mosaic of two Landsat thematic mapper images acquired May 30, 1991, reveals a dark smoke plume 30-60 km wide extending hundreds of kilometers south of Kuwait City along the Persian Gulf. Smoke coming from the Raudhatain and Sabriyah oil fields blew across the Gulf of Kuwait and over Kuwait City, joined with smoke from the Greater Burgan and Minagish fields, and continued southward over smaller villages and regions of desert agriculture consisting of hundreds of axially irrigated fields in both Kuwait and Saudi Arabia. One agricultural region in Kuwait was completely obscured by the smoke. The light colored limestone gravel and sand surface was darkened by oil lakes near the wells, and by oil drizzling out of the plume downwind of the wells. Most fires produced either a light or dark plume, and the separate plumes mixed to form a combined plume much darker than the land surface, but slightly more reflective than the Gulf waters. A few of the hottest fires had no visible plume, and are presumably associated with methane combustion. The last of the Kuwait fires was reportedly extinguished in November of 1991. Continued monitoring is needed to assess the impact of emissions from both burning and nonburning oil wells on the region's climate, as well as on the agriculture, fishing, and other activities essential to life in the region.

Cost effective modular unit for cleaning oil and gas field waste water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zinberg, M.B.; Nenasheva, M.N.; Gafarov, N.A.

1996-12-31

Problems of environmental control involving conservation of water resources are vital for the development of giant oil and gas condensate fields near Caspian Sea (Russia) characterized by water shortages. One of the urgent tasks of oil production industry is to use all field waste water consisting of underground, processing and rain water. It was necessary to construct a new highly effective equipment which could be used in local waste water treatment. Now we have at our disposal a technology and equipment to meet the requirements to the treated water quality. Thus we have installed a modular unit of 100 m{supmore » 3}/a day capacity to clean waste water from oil products, suspended matter and other organic pollutants at Orenburg oil and gas condensate field, Russia. The unit provides with a full treatment of produced water and comprises a settling tank with adhesive facility, the number of sorption filters, Trofactor bioreactors and a disinfecting facility. The equipment is fitted into three boxes measuring 9 x 3.2 x 2.7 in each. The equipment is simple in design that enables to save money, time and space. Sorption filters, bioreactors as well as the Trofactor process are a part of know-how. While working on the unit construction we applied well known methods of settling and sorption. The process of mechanic cleaning is undergoing in the following succession: (1) the gravitational separation in a settling tank where the floated film oil products are constantly gathered and the sediment is periodically taken away, (2) the settled water treatment in sorption Filters of a special kind.« less

A road damage and life-cycle greenhouse gas comparison of trucking and pipeline water delivery systems for hydraulically fractured oil and gas field development in Colorado

PubMed Central

Duthu, Ray C.

2017-01-01

The process of hydraulic fracturing for recovery of oil and natural gas uses large amounts of fresh water and produces a comparable amount of wastewater, much of which is typically transported by truck. Truck transport of water is an expensive and energy-intensive process with significant external costs including roads damages, and pollution. The integrated development plan (IDP) is the industry nomenclature for an integrated oil and gas infrastructure system incorporating pipeline-based transport of water and wastewater, centralized water treatment, and high rates of wastewater recycling. These IDP have been proposed as an alternative to truck transport systems so as to mitigate many of the economic and environmental problems associated with natural gas production, but the economic and environmental performance of these systems have not been analyzed to date. This study presents a quantification of lifecycle greenhouse gas (GHG) emissions and road damages of a generic oil and gas field, and of an oil and gas development sited in the Denver-Julesburg basin in the northern Colorado region of the US. Results demonstrate that a reduction in economic and environmental externalities can be derived from the development of these IDP-based pipeline water transportation systems. IDPs have marginal utility in reducing GHG emissions and road damage when they are used to replace in-field water transport, but can reduce GHG emissions and road damage by factors of as much as 6 and 7 respectively, when used to replace fresh water transport and waste-disposal routes for exemplar Northern Colorado oil and gas fields. PMID:28686682

A road damage and life-cycle greenhouse gas comparison of trucking and pipeline water delivery systems for hydraulically fractured oil and gas field development in Colorado.

PubMed

Duthu, Ray C; Bradley, Thomas H

2017-01-01

The process of hydraulic fracturing for recovery of oil and natural gas uses large amounts of fresh water and produces a comparable amount of wastewater, much of which is typically transported by truck. Truck transport of water is an expensive and energy-intensive process with significant external costs including roads damages, and pollution. The integrated development plan (IDP) is the industry nomenclature for an integrated oil and gas infrastructure system incorporating pipeline-based transport of water and wastewater, centralized water treatment, and high rates of wastewater recycling. These IDP have been proposed as an alternative to truck transport systems so as to mitigate many of the economic and environmental problems associated with natural gas production, but the economic and environmental performance of these systems have not been analyzed to date. This study presents a quantification of lifecycle greenhouse gas (GHG) emissions and road damages of a generic oil and gas field, and of an oil and gas development sited in the Denver-Julesburg basin in the northern Colorado region of the US. Results demonstrate that a reduction in economic and environmental externalities can be derived from the development of these IDP-based pipeline water transportation systems. IDPs have marginal utility in reducing GHG emissions and road damage when they are used to replace in-field water transport, but can reduce GHG emissions and road damage by factors of as much as 6 and 7 respectively, when used to replace fresh water transport and waste-disposal routes for exemplar Northern Colorado oil and gas fields.

Use of Acetate, Propionate, and Butyrate for Reduction of Nitrate and Sulfate and Methanogenesis in Microcosms and Bioreactors Simulating an Oil Reservoir.

PubMed

Chen, Chuan; Shen, Yin; An, Dongshan; Voordouw, Gerrit

2017-04-01

Acetate, propionate, and butyrate (volatile fatty acids [VFA]) occur in oil field waters and are frequently used for microbial growth of oil field consortia. We determined the kinetics of use of these VFA components (3 mM each) by an anaerobic oil field consortium in microcosms containing 2 mM sulfate and 0, 4, 6, 8, or 13 mM nitrate. Nitrate was reduced first, with a preference for acetate and propionate. Sulfate reduction then proceeded with propionate (but not butyrate) as the electron donor, whereas the fermentation of butyrate (but not propionate) was associated with methanogenesis. Microbial community analyses indicated that Paracoccus and Thauera ( Paracoccus - Thauera ), Desulfobulbus , and Syntrophomonas - Methanobacterium were the dominant taxa whose members catalyzed these three processes. Most-probable-number assays showed the presence of up to 10 7 /ml of propionate-oxidizing sulfate-reducing bacteria (SRB) in waters from the Medicine Hat Glauconitic C field. Bioreactors with the same concentrations of sulfate and VFA responded similarly to increasing concentrations of injected nitrate as observed in the microcosms: sulfide formation was prevented by adding approximately 80% of the nitrate dose needed to completely oxidize VFA to CO 2 in both. Thus, this work has demonstrated that simple time-dependent observations of the use of acetate, propionate, and butyrate for nitrate reduction, sulfate reduction, and methanogenesis in microcosms are a good proxy for these processes in bioreactors, monitoring of which is more complex. IMPORTANCE Oil field volatile fatty acids acetate, propionate, and butyrate were specifically used for nitrate reduction, sulfate reduction, and methanogenic fermentation. Time-dependent analyses of microcosms served as a good proxy for these processes in a bioreactor, mimicking a sulfide-producing (souring) oil reservoir: 80% of the nitrate dose required to oxidize volatile fatty acids to CO 2 was needed to prevent souring in both. Our data also suggest that propionate is a good substrate to enumerate oil field SRB. Copyright © 2017 American Society for Microbiology.

Targeting new wells in a mature field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Javed, M.S.

It has been estimated through a simulation study that about 20 million STB of oil can be recovered through infill drilling in the flank areas of one of the prolific, but depleting reservoirs (Arab C) in a Qatar offshore field. The area where this appreciable amount of oil (known as ``Cellar Oil``) exists, has been left unswept by the non-ideal location of the ``Dumpflooders`` -- injection wells, for pressure maintenance, which gravitate water from a source formation directly into the producing reservoir. This paper highlights the results of the simulation study of this mature reservoir, studied together with the underlyingmore » Arab D, where high oil concentrations are shown i the flank areas, between the OWC and the dumpflooders. Although, the existing flank production wells have been performing satisfactorily, it was found, from the study, that even prolonged production through these would not drain this trapped Cellar Oil; new wells must be drilled to recover it. The infill wells, proposed for this purpose, happen to be located in areas such that they can be completed dually in a horizontal mode with another underlying reservoir (Uwainat) having an oil rim, thus, further increasing the attractiveness of the project. The study also indicates the necessity of infill drilling in other parts of the Arab C and Arab D.« less

Bird Mortality in Oil Field Wastewater Disposal Facilities

NASA Astrophysics Data System (ADS)

Ramirez, Pedro

2010-11-01

Commercial and centralized oilfield wastewater disposal facilities (COWDFs) are used in the Western United States for the disposal of formation water produced from oil and natural gas wells. In Colorado, New Mexico, Utah, and Wyoming, COWDFs use large evaporation ponds to dispose of the wastewater. Birds are attracted to these large evaporation ponds which, if not managed properly, can cause wildlife mortality. The U.S. Fish and Wildlife Service (USFWS) and the U.S. Environmental Protection Agency (EPA) conducted 154 field inspections of 28 COWDFs in Wyoming from March 1998 through September 2008 and documented mortality of birds and other wildlife in 9 COWDFs. Of 269 bird carcasses recovered from COWDFs, grebes (Family Podicipedidae) and waterfowl (Anatidae) were the most frequent casualties. Most mortalities were attributed to oil on evaporation ponds, but sodium toxicity and surfactants were the suspected causes of mortality at three COWDFs. Although the oil industry and state and federal regulators have made much progress in reducing bird mortality in oil and gas production facilities, significant mortality incidents continue in COWDFs, particularly older facilities permitted in the early 1980’s. Inadequate operation and management of these COWDFs generally results in the discharge of oil into the large evaporation ponds which poses a risk for birds and other wildlife.

Bird mortality in oil field wastewater disposal facilities.

PubMed

Ramirez, Pedro

2010-11-01

Commercial and centralized oilfield wastewater disposal facilities (COWDFs) are used in the Western United States for the disposal of formation water produced from oil and natural gas wells. In Colorado, New Mexico, Utah, and Wyoming, COWDFs use large evaporation ponds to dispose of the wastewater. Birds are attracted to these large evaporation ponds which, if not managed properly, can cause wildlife mortality. The U.S. Fish and Wildlife Service (USFWS) and the U.S. Environmental Protection Agency (EPA) conducted 154 field inspections of 28 COWDFs in Wyoming from March 1998 through September 2008 and documented mortality of birds and other wildlife in 9 COWDFs. Of 269 bird carcasses recovered from COWDFs, grebes (Family Podicipedidae) and waterfowl (Anatidae) were the most frequent casualties. Most mortalities were attributed to oil on evaporation ponds, but sodium toxicity and surfactants were the suspected causes of mortality at three COWDFs. Although the oil industry and state and federal regulators have made much progress in reducing bird mortality in oil and gas production facilities, significant mortality incidents continue in COWDFs, particularly older facilities permitted in the early 1980's. Inadequate operation and management of these COWDFs generally results in the discharge of oil into the large evaporation ponds which poses a risk for birds and other wildlife.

Comparison of Atmospheric Pressure Chemical Ionization and Field Ionization Mass Spectrometry for the Analysis of Large Saturated Hydrocarbons.

PubMed

Jin, Chunfen; Viidanoja, Jyrki; Li, Mingzhe; Zhang, Yuyang; Ikonen, Elias; Root, Andrew; Romanczyk, Mark; Manheim, Jeremy; Dziekonski, Eric; Kenttämaa, Hilkka I

2016-11-01

Direct infusion atmospheric pressure chemical ionization mass spectrometry (APCI-MS) was compared to field ionization mass spectrometry (FI-MS) for the determination of hydrocarbon class distributions in lubricant base oils. When positive ion mode APCI with oxygen as the ion source gas was employed to ionize saturated hydrocarbon model compounds (M) in hexane, only stable [M - H] + ions were produced. Ion-molecule reaction studies performed in a linear quadrupole ion trap suggested that fragment ions of ionized hexane can ionize saturated hydrocarbons via hydride abstraction with minimal fragmentation. Hence, APCI-MS shows potential as an alternative of FI-MS in lubricant base oil analysis. Indeed, the APCI-MS method gave similar average molecular weights and hydrocarbon class distributions as FI-MS for three lubricant base oils. However, the reproducibility of APCI-MS method was found to be substantially better than for FI-MS. The paraffinic content determined using the APCI-MS and FI-MS methods for the base oils was similar. The average number of carbons in paraffinic chains followed the same increasing trend from low viscosity to high viscosity base oils for the two methods.

Concurrence of aqueous and gas phase contamination of groundwater in the Wattenberg oil and gas field of northern Colorado.

PubMed

Li, Huishu; Son, Ji-Hee; Carlson, Kenneth H

2016-01-01

The potential impact of rapid development of unconventional oil and natural gas resources using hydraulic fracturing and horizontal drilling on regional groundwater quality has received significant attention. Major concerns are methane or oil/gas related hydrocarbon (such as TPHs, BTEX including benzene, toluene, ethybenzene and xylene) leaks into the aquifer due to the failure of casing and/or stray gas migration. Previously, we investigated the relationship between oil and gas activity and dissolved methane concentration in a drinking water aquifer with the major finding being the presence of thermogenic methane contamination, but did not find detectable concentrations of TPHs or BTEX. To understand if aqueous and gas phases from the producing formation were transported concurrently to drinking water aquifers without the presence of oil/gas related hydrocarbons, the ionic composition of three water groups was studied: (1) uncontaminated deep confined aquifer, (2) suspected contaminated groundwater - deep confined aquifer containing thermogenic methane, and (3) produced water from nearby oil and gas wells that would represent aqueous phase contaminants. On the basis of quantitative and spatial analysis, we identified that the "thermogenic methane contaminated" groundwater did not have similarities to produced water in terms of ionic character (e.g. Cl/TDS ratio), but rather to the "uncontaminated" groundwater. The analysis indicates that aquifer wells with demonstrated gas phase contamination have not been contacted by an aqueous phase from oil and gas operations according to the methodology we use in this study and the current groundwater quality data from COGCC. However, the research does not prove conclusively that this the case. The results may provide insight on contamination mechanisms since improperly sealed well casing may result in stray gas but not aqueous phase transport. Copyright © 2015 Elsevier Ltd. All rights reserved.

POLICY ANALYSIS OF PRODUCED WATER ISSUES ASSOCIATED WITH IN-SITU THERMAL TECHNOLOGIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert Keiter; John Ruple; Heather Tanana

2011-02-01

Commercial scale oil shale and oil sands development will require water, the amount of which will depend on the technologies adopted and the scale of development that occurs. Water in oil shale and oil sands country is already in scarce supply, and because of the arid nature of the region and limitations on water consumption imposed by interstate compacts and the Endangered Species Act, the State of Utah normally does not issue new water rights in oil shale or oil sands rich areas. Prospective oil shale and oil sands developers that do not already hold adequate water rights can acquiremore » water rights from willing sellers, but large and secure water supplies may be difficult and expensive to acquire, driving oil shale and oil sands developers to seek alternative sources of supply. Produced water is one such potential source of supply. When oil and gas are developed, operators often encounter ground water that must be removed and disposed of to facilitate hydrocarbon extraction. Water produced through mineral extraction was traditionally poor in quality and treated as a waste product rather than a valuable resource. However, the increase in produced water volume and the often-higher quality water associated with coalbed methane development have drawn attention to potential uses of produced water and its treatment under appropriations law. This growing interest in produced water has led to litigation and statutory changes that must be understood and evaluated if produced water is to be harnessed in the oil shale and oil sands development process. Conversely, if water is generated as a byproduct of oil shale and oil sands production, consideration must be given to how this water will be disposed of or utilized in the shale oil production process. This report explores the role produced water could play in commercial oil shale and oil sands production, explaining the evolving regulatory framework associated with produced water, Utah water law and produced water regulation, and the obstacles that must be overcome in order for produced water to support the nascent oil shale and oil sands industries.« less

New Drop Fluidics Enabled by Magnetic-Field-Mediated Elastocapillary Transduction.

PubMed

Biswas, Saheli; Pomeau, Yves; Chaudhury, Manoj K

2016-07-12

This research introduces a new drop fluidics that uses a deformable and stretchable elastomeric film as the platform instead of the commonly used rigid supports. Such a soft film impregnated with magnetic particles can be modulated with an external electromagnetic field that produces a vast array of topographical landscapes with varying surface curvature, which, in conjunction with capillarity, can direct and control the motion of water droplets efficiently and accurately. When a thin layer of oil is present on this film that is deformed locally, a centrosymmetric wedge is formed. A water droplet placed on this oil-laden film becomes asymmetrically deformed, thus producing a gradient of Laplace pressure within the droplet and setting it in motion. A simple theory is presented that accounts for the droplet speed in terms of such geometric variables as the volume of the droplet and the thickness of the oil film covering the soft elastomeric film as well as material variables such as the viscosity of the oil and the interfacial tension of the oil-water interfaces. Following the verification of the theoretical result using well-controlled model systems, we demonstrate how the electromagnetically controlled elastocapillary force can be used to manipulate the motion of single and/or multiple droplets on the surface of the elastomeric film and how elementary operations such as drop fusion and thermally addressed chemical transformation can be carried out in aqueous droplets. It is expected that the resulting drop fluidics would be suitable for the digital control of drop motion by simply switching on and off the electromagnetic fields applied at different positions underneath the elastomeric film in a Boolean sequence. We anticipate that this method of directing and manipulating water droplets is poised for application in various biochemical reaction engineering situations, an example of which is the polymerase chain reaction (PCR).

Occurrence of oil in the Austin Chalk at Van field, Van Zandt County, Texas: A unique geologic setting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowe, J.T.; Carrington, D.B.

1990-09-01

The Austin Chalk is buried to a depth of only 2,100-2,500 ft and has retained primary microporosity unlike the typical deep fractured chalk reservoirs. The Van structure is a complexly faulted domal anticline created by salt intrusion and is approximately 2,000 ft higher than surrounding structures in the area. A major northwest-dipping fault acts as the primary trapping mechanism. The field has produced 0.5 billion BO from thick Woodbine sands since its discovery in 1929. Occurrence of oil in the Austin Chalk has been known since the field discovery, but prior completions were low rate oil producers. Recent development ofmore » a large fracture stimulation technique has resulted in increased production rates of up to 300 BOPD. The Austin Chalk reservoir limits were determined by isopaching feet of minimum productive resistivity having porosity above a cutoff value. The resistivity/porosity isopach showed a direct correlation between Austin Chalk productivity and the Austin Chalk structure and faulting pattern. Structural evidence along with oil typing indicate that the oil in the Austin Chalk has migrated upward along fault planes and through fault juxtaposition from the Woodbine sands 200 ft below the Austin Chalk. Thin-section and scanning electron microscopy work performed on conventional cores showed that the Van Austin Chalk formation is a very fine grained limestone composed primarily of coccoliths. Various amounts of detrital illite clay are present in the coccolith matrix. All effective porosity is micro-intergranular and ranges from 15 to 35%. Based on the core analyses, the main porosity reducing agent and therefore control on reservoir quality is the amount of detrital clay present filling the micropores. Permeability is very low with values ranging from 0.01 to 1.5 md. There is no evidence of significant natural fractures in the core. Artificial fractures are therefore required to create the permeability needed to sustain commercial production rates.« less

Effect of subsurface heterogeneity on free-product recovery from unconfined aquifers

NASA Astrophysics Data System (ADS)

Kaluarachchi, Jagath J.

1996-03-01

Free-product record system designs for light-hydrocarbon-contaminated sites were investigated to evaluate the effects of subsurface heterogeneity using a vertically integrated three-phase flow model. The input stochastic variable of the areal flow analysis was the log-intrinsic permeability and it was generated using the Turning Band method. The results of a series of hypothetical field-scale simulations showed that subsurface heterogeneity has a substantial effect on free-product recovery predictions. As the heterogeneity increased, the recoverable oil volume decreased and the residual trapped oil volume increased. As the subsurface anisotropy increased, these effects together with free- and total-oil contaminated areas were further enhanced. The use of multiple-stage water pumping was found to be insignificant compared to steady uniform pumping due to reduced recovery efficiency and increased residual oil volume. This observation was opposite to that produced under homogeneous scenarios. The effect of subsurface heterogeneity was enhanced at relatively low water pumping rates. The difference in results produced by homogeneous and heterogeneous simulations was substantial, indicating greater attention should be paid in modeling free-product recovery systems with appropriate subsurface heterogeneity.

Development of the Write Process for Pipeline-Ready Heavy Oil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee Brecher; Charles Mones; Frank Guffey

Work completed under this program advances the goal of demonstrating Western Research Institute's (WRI's) WRITE{trademark} process for upgrading heavy oil at field scale. MEG Energy Corporation (MEG) located in Calgary, Alberta, Canada supported efforts at WRI to develop the WRITE{trademark} process as an oil sands, field-upgrading technology through this Task 51 Jointly Sponsored Research project. The project consisted of 6 tasks: (1) optimization of the distillate recovery unit (DRU), (2) demonstration and design of a continuous coker, (3) conceptual design and cost estimate for a commercial facility, (4) design of a WRITE{trademark} pilot plant, (5) hydrotreating studies, and (6) establishmore » a petroleum analysis laboratory. WRITE{trademark} is a heavy oil and bitumen upgrading process that produces residuum-free, pipeline ready oil from heavy material with undiluted density and viscosity that exceed prevailing pipeline specifications. WRITE{trademark} uses two processing stages to achieve low and high temperature conversion of heavy oil or bitumen. The first stage DRU operates at mild thermal cracking conditions, yielding a light overhead product and a heavy residuum or bottoms material. These bottoms flow to the second stage continuous coker that operates at severe pyrolysis conditions, yielding light pyrolyzate and coke. The combined pyrolyzate and mildly cracked overhead streams form WRITE{trademark}'s synthetic crude oil (SCO) production. The main objectives of this project were to (1) complete testing and analysis at bench scale with the DRU and continuous coker reactors and provide results to MEG for process evaluation and scale-up determinations and (2) complete a technical and economic assessment of WRITE{trademark} technology to determine its viability. The DRU test program was completed and a processing envelope developed. These results were used for process assessment and for scaleup. Tests in the continuous coker were intended to determine the throughput capability of the coker so a scaled design could be developed that maximized feed rate for a given size of reactor. These tests were only partially successful because of equipment problems. A redesigned coker, which addressed the problems, has been build but not operated. A preliminary economic analysis conducted by MEG and an their engineering consultant concluded that the WRITE{trademark} process is a technically feasible method for upgrading bitumen and that it produces SCO that meets pipeline specifications for density. When compared to delayed coking, the industry benchmark for thermal upgrading of bitumen, WRITE{trademark} produced more SCO, less coke, less CO{sub 2} per barrel of bitumen fed, and had lower capital and operating costs. On the other hand, WRITE{trademark}'s lower processing severity yielded crude with higher density and a different product distribution for naphtha, light gas oil and vacuum oil that, taken together, might reduce the value of the SCO. These issues plus the completion of more detailed process evaluation and economics need to be resolved before WRITE{trademark} is deployed as a field-scale pilot.« less

Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama. Annual report, March 1996--March 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.

1997-08-01

Gilbertown Field is the oldest oil field in Alabama and produces oil from chalk of the Upper Cretaceous Selma Group and from sandstone of the Eutaw Formation along the southern margin of the Gilbertown fault system. Most of the field has been in primary recovery since establishment, but production has declined to marginally economic levels. This investigation applies advanced geologic concepts designed to aid implementation of improved recovery programs. The Gilbertown fault system is detached at the base of Jurassic salt. The fault system began forming as a half graben and evolved in to a full graben by the Latemore » Cretaceous. Conventional trapping mechanisms are effective in Eutaw sandstone, whereas oil in Selma chalk is trapped in faults and fault-related fractures. Burial modeling establishes that the subsidence history of the Gilbertown area is typical of extensional basins and includes a major component of sediment loading and compaction. Surface mapping and fracture analysis indicate that faults offset strata as young as Miocene and that joints may be related to regional uplift postdating fault movement. Preliminary balanced structural models of the Gilbertown fault system indicate that synsedimentary growth factors need to be incorporated into the basic equations of area balance to model strain and predict fractures in Selma and Eutaw reservoirs.« less

Mineral nutrient recovery from pyrolysis systems

USDA-ARS?s Scientific Manuscript database

Bioenergy crops such as high-energy sorghum (HES), bioenergy rice, corn stover, and switchgrass can be thermo-chemically converted by pyrolysis to produce bio-oil, synthesis gas from non-condensable gases, and biochar. The biochar fraction can be recycled back to the production field to improve soil...

Application of phase correction to improve the interpretation of crude oil spectra obtained using 7 T Fourier transform ion cyclotron resonance mass spectrometry.

PubMed

Cho, Yunju; Qi, Yulin; O'Connor, Peter B; Barrow, Mark P; Kim, Sunghwan

2014-01-01

In this study, a phase-correction technique was applied to the study of crude oil spectra obtained using a 7 T Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). 7 T FT-ICR MS had not been widely used for oil analysis due to the lower resolving power compared with high field FT-ICR MS. For low field instruments, usage of data that has not been phase-corrected results in an inability to resolve critical mass splits of C3 and SH4 (3.4 mDa), and (13)C and CH (4.5 mDa). This results in incorrect assignments of molecular formulae, and discontinuous double bond equivalents (DBE) and carbon number distributions of S1, S2, and hydrocarbon classes are obtained. Application of phase correction to the same data, however, improves the reliability of assignments and produces continuous DBE and carbon number distributions. Therefore, this study clearly demonstrates that phase correction improves data analysis and the reliability of assignments of molecular formulae in crude oil anlayses.

Property description and fact-finding report for NPR-3 Natrona County, Wyoming. Addendum to 22 August 1996 study of alternatives for future operations of the naval petroleum and oil shale reserves NPR-3

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The U.S. Department of Energy has asked Gustavson Associates, Inc. to serve as an Independent Petroleum Consultant under contract DE-AC01-96FE64202. This authorizes a study and recommendations regarding future development of Naval Petroleum Reserve No. 3 (NPR-3) in Natrona County, Wyoming. The report that follows is the Phase I fact-finding and property description for that study. The United States of America owns 100 percent of the mineral rights and surface rights in 9,321-acre NPR-3. This property comprises the Teapot Dome oil field and related production, processing and other facilities. Discovered in 1914, this field has 632 wells producing 1,807 barrels ofmore » oil per day. Production revenues are about $9.5 million per year. Remaining recoverable reserves are approximately 1.3 million barrels of oil. Significant plugging and abandonment (P&A) and environmental liabilities are present.« less

The Barrow Island oilfield development plan, Western Australia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartlett, R.M.

1996-12-31

Barrow Island lies 55 kms off the coast of Western Australia, 90 kms north-northeast of Onslow and 1300 kms north of Perth. Oil production began on Barrow Island in 1967 with the 250 millionth barrel being produced in 1992. By 1991, the island had reached the point where: The field, as currently defined, would reach its economic limit early in the next century if operating expenses remained constant and Operating expense was most likely to rise, as aging facilities and infrastructure required increasing maintenance and/or environmental enhancements. In 1991, studies were triggered to develop an integrated plan for Barrow Islandmore » to maximize Net Present Value, targeting both increasing reserves and decreasing operating costs. The studies focused on developing answers to the following four questions: Where is the remaining oil? How can oil recovery be improved? How can current operations be improved? What is the optimal plan for the field? The outcome of the 3 year study has provided answers to these four questions, combining to maximize NPV and possibly result in another 15-25 years of field life.« less

The Barrow Island oilfield development plan, Western Australia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartlett, R.M.

1996-01-01

Barrow Island lies 55 kms off the coast of Western Australia, 90 kms north-northeast of Onslow and 1300 kms north of Perth. Oil production began on Barrow Island in 1967 with the 250 millionth barrel being produced in 1992. By 1991, the island had reached the point where: The field, as currently defined, would reach its economic limit early in the next century if operating expenses remained constant and Operating expense was most likely to rise, as aging facilities and infrastructure required increasing maintenance and/or environmental enhancements. In 1991, studies were triggered to develop an integrated plan for Barrow Islandmore » to maximize Net Present Value, targeting both increasing reserves and decreasing operating costs. The studies focused on developing answers to the following four questions: Where is the remaining oil How can oil recovery be improved How can current operations be improved What is the optimal plan for the field The outcome of the 3 year study has provided answers to these four questions, combining to maximize NPV and possibly result in another 15-25 years of field life.« less

Evaporite geometries and diagenetic traps, lower San Andres, Northwest shelf, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keller, D.R.

An east-west-trending belt of lower San Andres oil fields extends 80 mi across southeastern New Mexico from the Pecos River near Roswell to the Texas-New Mexico border. These fields are along a porosity pinch-out zone where porous carbonates grade laterally into bedded anhydrite and halite. The lower San Andres traps are associated with pre-Tertiary structural or stratigraphic traps. Oil and water production relationships from these fields are not consistent with present-day structure. These fields have been commonly interpreted to be hydrodynamic traps created by the eastern flow of fresh surface water that enters the lower San Andres outcrops west ofmore » Pecos River. There is no evidence, however, that surface water has moved through the lower San Andres in this area. This conclusion is supported by the fact that formation-water resistivities are uniform throughout the producing trend, no significant dissolution of carbonates or evaporites has occurred, and there has been no increase in biogradation of oils adjacent to the lower San Andres outcrops. These fields actually are diagenetic traps created by porosity occlusion in the water column beneath the oil accumulations. Hydrocarbons originally were trapped in pre-Tertiary structural and structural-stratigraphic traps. Bedded evaporites were effective barriers to vertical and lateral hydrocarbon migration. Eastward tilting of the Northwest shelf during the Tertiary opened these traps, but the oil remained in these structurally unfavorable positions because of the diagenetic sealing. The gas-solution drive in these reservoirs is a result of this sealing. The sequence of events leading to diagenetic entrapment include (1) Triassic and Jurassic migration of hydrocarbons into broad, low-relief post-San Andres structural and structural-stratigraphic traps; (2) rapid occlusion of porosity in the water column beneath oil reservoirs, and (3) Tertiary tilt-out traps.« less

A review of the evaluation of TENORM levels at the produced water lagoon of the Minagish oil field using high-resolution gamma-ray spectrometry

NASA Astrophysics Data System (ADS)

Shams, H. M.; Bradley, D. A.; Alshammari, H.; Regan, P. H.

2017-11-01

An evaluation of the specific activity concentrations associated with technologically enhanced naturally occurring radioactive materials (TENORM) and anthropogenic radionuclides has been undertaken as part of a systematic study to provide a radiological map of the outer boundary of the produced water lagoon located in the Minagish oil field in the south west of the State of Kuwait. The lagoon contains material from the discharge of produced water which is a by-product of oil production in the region. The lagoon samples were prepared and placed into sealed, marinelli beakers for a full gamma-ray spectrometric analysis using a high-resolution, low-background, high-purity germanium detection systems at the University of Surrey Environmental Radioactivity Laboratory. Of particular interest are the calculation of the activity concentrations associated with members of the decay chains following decays of the primordial radionuclides of the 238U chain (226Ra, 214Pb, 214Bi) and the 232Th chain (228Ra, 228Ac, 212Pb, 212Bi, 208Tl), and the enhanced concentrations of radium isotopes. This conference paper presents an overview summary of the experimental samples which have been measured and the analysis techniques applied, including isotopic correlation plots across the sample region. The result shows the expected significant increase in 226Ra (and progeny) concentrations compared to the NORM values previously reported by our group for the overall terrain in Kuwait.

Cash value of 3-D seismic to a producing field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bligh, R.; Thompson, S.

1996-05-01

Recent years have produced many reservoir management examples guided by seismic where clear value in excess of cost can be demonstrated. One of these examples was a 3-D survey recorded in the winter of 1994 over the Wytch Farm oil field in southern England, operated by BP on behalf of a consortium, including Arco, Clyda, Premier, Goal and Purbeck. A joint BP-CGG case history of this survey was presented at the 1995 SEG Convention in Houston and will be repeated at the 1996 AAPG Convention in San Diego. A brief summary is provided in this paper.

Essential oil obtained from micropropagated lavender, its effect on HSF cells and application in cosmetic emulsion as a natural protective substance.

PubMed

Andrys, D; Adaszyńska-Skwirzyńska, M; Kulpa, D

2018-04-01

The aim of the study was to determine the influence of the essential oils isolated from the field - grown and micropropagated in vitro narrow - leaved lavender of the 'Munstead' cultivar, on human skin cells, and their capability to synthesise procollagen. The amount of procollagen type I produced by fibroblast cells was determined using ELISA kit. Essential oil isolated from micropropagated lavender was further used as a protective ingredient against the development of microorganisms in O/W cosmetic emulsion. The presented results demonstrate that the use of 0.01, 0.001 and 0.0001% essential oils isolated from in vitro plants stimulate HSF cells to the production of procollagen. It was further performed that the tested essential oil used in the concentration of 0.1% in a cosmetic emulsion is characterised by preservative effect for cosmetic preparations for the period of 3 months.

Use of water-external micellar dispersions in oil recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, S.C.

1970-04-14

A water-external micellar dispersion followed by a mobility buffer and a water drive were used for enhanced oil recovery. Field Berea sandstone cores (19.6 percent porosity, 387 md permeability) were saturated with brine (16,500 ppM sodium chloride), flooded with crude oil from the Henry lease in Illinois (viscosity of 5.9 cp at 72/sup 0/F, specific gravity of 0.833), and waterflooded with water from Henry lease (17,210 ppM TDS). The micellar dispersion followed by the mobility buffer produced 99.6 percent of the oil in the core. The micellar slug contained ammonium petroleum sulfonate (MW 450), Henry crude oil, isopropanol, nonyl phenol,more » sodium hydroxide, and water from the Palestine water reservoir in Palestine, Illinois (412 ppM TDS). No. 530 Pusher, ammonium thiocyanate, isopropanol, and Palestine water were in the mobility buffer.« less

Beneficial Reuse of Produced and Flowback Water

EPA Pesticide Factsheets

Water reuse and recycling is a significant issue in the development of oil and gas shale plays in the United StatesDrilling operations – 60,000 to 650,000 gallons per wellHydraulic fracturing operations – 3 million to 5 million gallons per wellDefinition of produced water and flowback waterInteractions of water quality constituents as they relate to water reuse and recyclingTesting criteria in the laboratory and field operations

Chemical and biological monitoring of MIOR on the pilot area of Vyngapour oil field, West Sibera, Russia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arinbasarov, M.U.; Murygina, V.P.; Mats, A.A.

1995-12-31

The pilot area of the Vyngapour oil field allotted for MIOR tests contains three injection and three producing wells. These wells were treated in summer 1993 and 1994. Before, during, and after MIOR treatments on the pilot area the chemical compounds of injected and formation waters were studied, as well as the amount and species of microorganisms entering the stratum with the injected water and indigenous bacteria presented in bottomhole zones of the wells. The results of monitoring showed that the bottomhole zone of the injection well already had biocenosis of heterotrophic, hydrocarbon-oxidizing, methanogenic, and sulfate-reducing bacteria, which were besidesmore » permanently introduced into the reservoir during the usual waterflooding. The nutritious composition activated vital functions of all bacterial species presented in the bottomhole zone of the injection well. The formation waters from producing wells showed the increase of the content of nitrate, sulfate, phosphate, and bicarbonate ions by the end of MIOR. The amount of hydrocarbon-oxidizing bacteria in formation waters of producing wells increased by one order. The chemical and biological monitoring revealed the activation of the formation microorganisms, but no transport of food industry waste bacteria through the formation from injection to producing wells was found.« less

Assessment of the petroleum, coal, and geothermal resources of the Economic Community of West African States (ECOWAS) region

USGS Publications Warehouse

Mattick, R. E.

1982-01-01

Approximately 85 percent of the land area of the ECOWAS (Economic Community of West African States) region is covered by basement rocks (igneous and highly metamorphosed rocks) or relatively thin layers of Paleozoic, Upper Precambrian, and 'Continental Intercalaire? sedimentary rocks. These areas have little or no petroleum potential. Areas of the ECOWAS region that have potential for petroleum production or potential for increased petroleum production include the narrow belt of sedimentary rocks that stretches along the continental margin from Mauritania to Nigeria and the Niger Delta and the Benue depression. The Senegal Basin, located on the continental margin of Mauritania, Senegal, Gambia, Guinea Bissau, and Guinea, has been intensely explored by the oil industry and most of the larger structures onshore and on the shelf probably have been tested by drilling with little or no resulting commercial production. Unless basic ideas pertaining to the petroleum geology of the Senegal Basin are revised, future discoveries are expected to be limited to small fields overlooked by industry at a time when petroleum prices were low. On the continental shelf of Sierra Leone and the continental shelf of northeast and central Liberia, the sedimentary rocks are relatively thin, and industry has shown little interest in the area. On the continental rise of these countries, however, the sedimentary section, deposited in a complex fault-block system, increases in thickness. A renewal of industry interest in this deep-water area will probably follow further development of deep-water production technology. A recent oil discovery on the continental slope off the Ivory Coast is expected to spur further exploration offshore of southeastern Liberia, Ivory Coast, Ghana, Togo, and Benin. This relatively unexplored area in the Gulf of Guinea has good possibilities .for the discovery of giant oil fields. Nigeria's oil development from the Niger Delta may have peaked, as 13 of 14 giant oil fields were discovered prior to 1969 and the greatest number of fields were discovered in the period 1965 through 1967. Like delta regions in other parts of the world, individual oil fields of the Niger Delta are small to medium by world standards and future discoveries, therefore, are likely to reflect this reality. The natural gas resources of the Niger Delta, unlike its oil resources, are comparatively underdeveloped. Parts of the Benue depression in Nigeria and Niger could contain significant deposits of petroleum. The lower Benue depression, immediately north of the Niger Delta, has been extensively explored by drilling. Except for noncommercial discoveries of oil and gas and traces of oil and gas on the ground surface, the results of exploration in the lower Benue depression were negative. However, in the Lake Chad area of Chad and in southern Chad near the Central African Republic boundary, oil and gas discoveries were made just prior to the cessation of all drilling and exploration activity in early 1979. It is rumored that these discoveries may be large although little information is available. The relation between the two areas in Chad and their overall relation to the Benue depression is poorly understood; however, the possibility of thick sedimentary sections containing Cretaceous marine source rock and Tertiary reservoir beds-all contained within grabens in a highly faulted failed-arm system subjected to high heat flow--is attractive. Of the ECOWAS countries, only Nigeria and Niger produce coal commercially. Nigeria produces subbituminous coal from Paleocene-Maestrichtian and Maestrichtian (Late Cretaceous) age rocks of the Niger Delta region; reserves are estimated, on the basis of extensive drilling, to be 350 million tons (standard coal equivalent). In addition, lignite deposits of the Niger Delta appear to be large but have not been developed. Niger produces small amounts of coal used locally by uranium mine and mill operations from C

Microfluidic diffusivity meter: a tool to optimize CO2 driven enhanced oil recovery

NASA Astrophysics Data System (ADS)

Puneeth, S. B.; Kim, Young Ho; Goel, Sanket

2017-02-01

As the energy demands continue to swell with growing population and there persists a lack of unexploited oilfields, the prime focus of any nation would be to maximize the oil recovery factor from existing oil fields. CO2-Enhanced oil recovery is a process to improve the recovery of crude oil from an oil field and works at high pressure and in very deep conditions. CO2 and oil are miscible at high pressure, resulting in low viscosity and oil swells. This swelling can be measured based on mathematical calculations in real time and correlated with the CO2 concentration. This process has myriad advantages over its counterparts which include being able to harness oil trapped in reservoirs besides being cheaper and more efficient. A Diffusivity meter is inevitable in the measurement of the diffusion co-efficient of two samples. Diffusivity meters currently available in the market are weighed down by disadvantages like the requirement of large samples for testing, high cost and complexity. This elicits the need for a Microfluidic based diffusivity meter capable of analyzing Nano-liter sample volumes besides being more precise and affordable. The scope of this work involves the design and development of a Microfluidic robust and inexpensive prototype diffusivity meter using a capillary tube and endorsing its performance by comparison of results with known diffusivity range and supervision of the results with an electronic microscope coupled to PC and Data Acquisition System. The prototype produced at the end of the work is expected to outweigh disadvantages in existing products in terms of sample size, efficiency and time saving.

Washing ashore: The politics of offshore oil in northern Angola

NASA Astrophysics Data System (ADS)

Reed, Kristin Michelle

This dissertation examines the political ecology of Angolan oil, by exploring state and corporate political economies; historical convergences of violence and capital; and struggles over the costs and benefits of oil production from the perspective of artisanal fishing and farming communities in the extractive zones. Angola is sub-Saharan Africa's second-largest oil producer but revenues from the enclave sector in oil rarely trickle down to the impoverished populace. The Angolan government strategically invests petrodollars in patronage networks to bolster their power; and watchdog agencies claim top officials divert the balance to offshore accounts. While the enclaved nature of production facilitates the restricted distribution of oil monies by concentrating services and revenue streams, the distortions and externalities that bleed out from these enclaves increase the misery of Angolans---especially those living in the extractive zones. By focusing on the lived experience of extraction, I explore the politics of oil through the forms of violence and degradation threatening the lives and livelihoods of local people. Most of Angola's oil is produced from offshore fields, so oil spills present a considerable risk to the health of local communities and ecosystems. The fishers and fish traders suffering from oil spills demand compensation from the liable oil corporations, yet the skewed system of disbursements only reaches the most powerful claimants. Moreover, faced with a repressive and unresponsive government, communities in extractive zones have come to rely on the same corporations for schools and health posts in a system I refer to as oil-backed development. I demonstrate that local histories of violence, national political exigencies, and transnational corporate interests govern the distribution of oil-backed development projects. Furthermore, I argue that the Angolan government leverages corporate donations for development to suit its own exclusionary interests and to gain control over dissidents and resources. In this way, oil-backed development complements more militant forms of territorialization while maintaining the exclusionary institutions and corrupt leadership that deprive Angolans of a fair share of the country's resource wealth.

Petroleum geology and resource assessment of the Timan-Pechora Basin, USSR, and the adjacent Barents-northern Kara shelf

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ulmishek, G.

1982-06-01

The regions discussed contain thick sequences of sedimentary rocks ranging in age from early Paleozoic to Late Cretaceous and, occasionally, Cenozoic. Over 50 oil and gas fields, including two giants, are found in the Timan-Pechora Basin. The Barents-northern Kara shelf is still in the earliest stage of exploration. This report considers (1) tectonic regionalization of the Timan-Pechora Basin and major structures in each region; (2) facies characteristics of the sedimentary cover and the history of geological development; (3) the main hydrogeological features; (4) producing regions of each basin and the major oil and gas fields; (5) specificity of oil-gas generationmore » and formation of fields; and (6) geology and conditions for expected productivity of the Barents-northern Kara shelf. Initial recoverable petroleum resources of the Timan-Pechora basin are estimated at 0.86 x 10/sup 9/ t (6.4 x 10/sup 9/ bbl) of oil and 1.7 x 10/sup 12/ m/sup 3/ (60 TCF) of gas, of which 0.41 x 10/sup 9/ t (3.0 x 10/sup 9/ bbl) of oil and 1.2 x 10/sup 12/ m/sup 3/ (42 TCF) of gas are yet to be discovered. Potential recoverable resources of the Barents-northern Kara shelf are estimated at 3.2 x 10/sup 9/ t (23.7 x 10/sup 9/ bbl) of oil and 10.2 x 10/sup 12/ m/sup 3/ (360 TCF) of gas.« less

Organic and inorganic species in produced water: Implications for water reuse

USGS Publications Warehouse

Kharaka, Yousif K.; Rice, Cynthia A.

2004-01-01

Currently 20-30 billion barrels of formation water are co-produced annually in the USA with conventional oil and natural gas. The large database on the geochemistry of this produced water shows salinities that vary widely from ~5,000 to >350,000 mg/L TDS. Chloride, Na and Ca are generally the dominant ions, and concentrations of Fe, Mn, B, NH3 and dissolved organics, including, BTEX, phenols and poly aromatic hydrocarbons (PAHs) may be relatively high. Hazardous concentrations of NORMs, including Ra-226 and Rn-222 have been reported in produced water from several states.Coal-bed methane (CBM) wells currently produce close to a billion barrels of water and deliver ~8% of total natural gas. The salinity of this produced water generally is lower than that of water from petroleum wells; salinity commonly is 1,000-20,000 mg/L, but ranges to150,000 mg/L TDS. Most CBM wells produce Na-HCO3-Cl type water that is low in trace metals and has no reported NORMs. This water commonly has no oil and grease and has relatively low DOC, but its organic composition has not been characterized in detail. The water is disposed of by injection into saline aquifers, through evaporation and/or percolation in disposal pits, road spreading, and surface discharge. Water that has an acceptable salinity and sodium absorption ratio (SAR) is considered acceptable for surface discharge and for injection into freshwater aquifers.As an alternative to costly disposal, low salinity produced water is being considered for reclamation, especially in the arid western USA. The cost of reclaiming this water to meet irrigation, industrial and drinking water standards was evaluated in a 10 gpm pilot field study at Placerita oil field, California. This produced water had a low salinity of ~8,000 mg/L, but high concentration of Si and organics. Removal of B, Si, NH3 and especially organics from this water proved difficult, and the estimated treatment cost was high at $0.08-$0.39/bbl for water treated for industrial and municipal uses.

Flow Analysis of a Rising Crude Oil Micro-Droplet Affected by Attached Microbial Streamers

NASA Astrophysics Data System (ADS)

Amaro, Matthew; White, Andrew; Jalali, Maryam; Sheng, Jian

2017-11-01

Microfluidic experiments show bacteria flowing past a pinned crude oil droplet produce microbial aggregates and streamers on the oil-water interface. High speed DIC microscopy at 1000 fps for 1 sec with a sampling interval of 10 min captures the evolving flow and bacterial motility as well as adhesion, aggregation and streamer events. With bacteria as tracers, velocity measurements are acquired with in-house PIV-assisted PTV software. Flow fields with spatial resolution 2.5 μm are measured around an O(100) μm drop in a 700 ×700 μm window. Full budgets of the 2D Navier-Stokes equation are faithfully resolved to determine pressure gradients by performing the balance over a control volume enclosing the droplet. Pressure gradients are integrated over the border of the control region to obtain pressure profiles at the leading and trailing edges. A momentum balance can be used to determine the drag induced by the drop and any attached streamers. Cases with and without streamers and their differing flow features are presented. Additionally streamers produce nonzero curl in the pressure gradient field providing a tool for identifying the position of otherwise invisible streamers. Ongoing experiments and future applications of the tools presented here will be discussed. Funded by GoMRI, NSF, ARO.

Environmental Impacts of Petroleum Production: Initial Results from the Osage-Skiatook Petroleum Environmental Research Sites, Osage County, Oklahoma

USGS Publications Warehouse

Kharaka, Yousif K.; Otton, James K.

2003-01-01

Exploration for and production of petroleum have caused major detrimental impacts to soils, surface and ground waters, and the local ecosystems in the United States. These impacts arise primarily from the improper disposal of large volumes of saline water produced with oil and gas, from accidental hydrocarbon and produced water releases, and from abandoned oil wells that were not correctly sealed. It is important to understand the long-term and short-term effects of produced water and hydrocarbon releases from these sites in order to develop risk-based remediation plans. Remediation is particularly needed in aging and depleted fields where land use is changing from petroleum production to residential, agricultural or recreational uses. About 20 scientists from the USGS and other governmental agencies and academia are involved in a multidisciplinary investigation to study the transport, fate, and natural attenuation of inorganic salts, trace metals, organic compounds and radionuclides present in produced water, and their impacts at the Osage-Skiatook Petroleum Environmental Research (OSPER) 'A' and 'B' sites, located on the Osage Reservation in Osage County, Oklahoma. Stakeholders in the project include the Osage Nation, which holds the mineral rights, the Bureau of Indian Affairs with trust responsibility, and the Army Corps of Engineers, which owns the surface rights at these sites and manages adjacent Skiatook Lake. The 4250-hectare Skiatook Lake provides drinking water to local Tulsa suburban communities and a rural water district, and offers recreational fishing and boating opportunities to tens of thousands of visitors each year. Approximately 1.5 and 1.0 hectare of land at the OSPER 'A' (depleted Lester lease) and 'B' (active Branstetter lease) sites, respectively, are affected by salt scarring, tree kills, soil salinization and brine and petroleum contamination due to the leakage of produced water and associated hydrocarbons from brine pits and accidental releases from active and inactive pipes and tank batteries. The leases are typical of many depleted and aging petroleum fields in Osage County, which ranks among the top oil and gas producing counties in Oklahoma with about 39,000 wells. Oil and gas production has occurred in Osage county for over one hundred years, but current production is mainly from stripper wells (averaging ~2.8 bbl/d oil and >30 bbl/d brine) that are shallow, mostly 300-700 m in depth, and produce from several sandstones of Pennsylvanian age. Results to date show that the produced water source is a Na-Ca-Cl brine (~150,000 mg/L total dissolved solids), with relatively high concentrations of Mg, Sr, and NH4, but low SO4 and H2S. With the exception of Fe and Mn, the concentrations of trace metals are low. Results also show that some and, eventually, the bulk, of inorganic salts and some dissolved organic species in the released brine from both sites will reach Skiatook Lake. Results at the 'A' site show that the salts have essentially been removed from the sandy soil which formed in a surficial layer of eolian sand, but degraded and weathered oil persists on the surface of old oil and brine pits, close to sites of old tanks, on old channels that carried oil from tanks to the oil pits and other impacted areas. Results also show a plume of high salinity water (5,000-30,600 mg/L TDS) is present at intermediate depths that extend from below the old oil and brine pits to Skiatook Lake. No liquid petroleum was found in the contaminated groundwater, but soluble petroleum byproducts, including organic acid anions and other volatile organic compounds (VOCs) are present. Results to date clearly show that significant amounts of salts from produced-water releases and petroleum hydrocarbons still remain in the soils and rocks of the impacted area after more than 60 years of natural attenuation. At the 'B' site significant amounts of produced water from the two active brine pits percolate into th

Screening of biosurfactant-producing bacteria from offshore oil and gas platforms in North Atlantic Canada.

PubMed

Cai, Qinhong; Zhang, Baiyu; Chen, Bing; Song, Xing; Zhu, Zhiwen; Cao, Tong

2015-05-01

From offshore oil and gas platforms in North Atlantic Canada, crude oil, formation water, drilling mud, treated produced water and seawater samples were collected for screening potential biosurfactant producers. In total, 59 biosurfactant producers belong to 4 genera, namely, Bacillus, Rhodococcus, Halomonas, and Pseudomonas were identified and characterized. Phytogenetic trees based on 16S ribosomal deoxyribonucleic acid (16S rDNA) were constructed with isolated strains plus their closely related strains and isolated strains with biosurfactant producers in the literature, respectively. The distributions of the isolates were site and medium specific. The richness, diversity, and evenness of biosurfactant producer communities in oil and gas platform samples have been analyzed. Diverse isolates were found with featured properties such as effective reduction of surface tension, producing biosurfactants at high rate and stabilization of water-in-oil or oil-in-water emulsion. The producers and their corresponding biosurfactants had promising potential in applications such as offshore oil spill control, enhancing oil recovery and soil washing treatment of petroleum hydrocarbon-contaminated sites.

Development and application of a new biotechnology of the molasses in-situ method; detailed evaluation for selected wells in the Romashkino carbonate reservoir

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagner, M.; Lungerhausen, D.; Murtada, H.

1995-12-31

On the basis of different laboratory studies, by which special strains of the type Clostridium tyrobutyricum were found, the application of molasses in-situ method for the enhanced recovery of oil in Romashkino oil field was executed. In an anaerobic, 6%-molasses medium the strains produce about 11,400 mg/l of organic acids (especially butyric acid), 3,200 mg/l ethanol, butanol, etc., and more than 350 ml/g of molasses biogas with a content of 80% C0{sub 2} and 20% H{sub 2}. The metabolics of Clostridium tyrobutyricum depress the growth of SRB, whereas methanogenic bacteria grow in an undiluted fermented molasses medium very well. Inmore » this way the dominant final fermentation process is methanogenesis. By laboratory studies with original cores under the conditions of the carbonate reservoir in Bashkir, the recovery of oil increased from 15% after waterflooding to 29% OOIP during the treatment with molasses and bacteria. We developed a new biotechnological method for a self-regulated, automatic continuous culture and constructed a special pilot plant with a high technical standard. The plant produced during the pilot on Romashkino field (September 1992 to August 1994) about 1,000 m{sup 3} of clean inoculum with a content of 3-4 billion cells per ml. This inoculum was injected in slugs together with 15,000 m{sup 3} of molasses medium, first in one, later in five wells. We will demonstrate for two example wells the complex microbiological and chemical changes in the oil, gas, and water phases, and their influences on the recover of oil.« less

Novel chemicals from plants via bioengineering. An overview.

PubMed

Kolodziejczyk, P P; Shahidi, F

1999-01-01

Novel chemicals were traditionally extracted from medicinal plants or produced synthetically. However, new development in the field of bioengineering has allowed production of novel products from plants such as edible and industrial oils as well as specific chemicals which could be used as foods with remedial effects.

Assessment of the physicochemical and microbiological status of western Niger Delta soil for crude oil pollution bioremediation potential.

PubMed

Ejechi, Bernard O; Ozochi, Chizoba A

2015-06-01

The physical, chemical and microbiological characteristics of the soil across the western Niger Delta area of Nigeria were determined to assess its potential for natural remediation of crude oil pollution. The pH (oil-producing area, 6.1 ± 1.1; non-oil producing, 5.9 ± 0.9) and temperature (28-35 °C in both areas) were favourable to natural remediation, while the fluctuating moisture (7.7-45.6 %) and the dominant sandy soil textural classes (70 %) were limitations. The carbon nitrogen phosphorus (CNP) ratio markedly exceeded recommended 100:10:1, while the cation exchange capacity was below acceptable range. Counts of heterotrophic bacteria, fungi and hydrocarbon-utilising and nitrogen-fixing bacteria (mean range log10 3.8 ± 1.5-6.52 ± 0.9 cfu/g) were favourable having markedly exceeded the minimum counts required. Crude oil loss was highest in loam soil, but significantly (P = 0.00) increased in all soil textural classes including sandy soils after amendment with cow dung/poultry dropping and manual aeration in laboratory and 8-month field tests as indicated by two-way ANOVA. Thus, the overall assessment is that while CNP can be viewed as the major limiting factor to natural oil pollution remediation in the western Niger Delta soil, its influence can be minimised by the amendment indicated in the study.

Water Issues Associated with Increasing Unconventional Oil Production in the Permian Basin

NASA Astrophysics Data System (ADS)

Reedy, R. C.; Scanlon, B. R.; Male, F.; Walsh, M.

2017-12-01

The Permian Basin is being transformed from a major conventional oil play to the world's largest unconventional play; however, managing water for this transition is critical in this semiarid region. The study included quantifying produced water volumes with oil and gas production along with water demands for hydraulic fracturing using a detailed well-by-well analysis. Our results show that oil wells in conventional reservoirs generate large volumes of produced water relative to oil production with produced water to oil ratios of 13 (i.e. 13 barrels [bbl] of water relative to a bbl of oil). However, produced water from conventional reservoirs has been mostly injected back into the pressure-depleted oil-producing reservoirs for enhanced oil recovery using water flooding. Unconventional horizontal wells use large volumes of water for hydraulic fracturing that has been markedly increasing by factors of 10 - 16 per well and by factors of 7-10 after dividing by lateral well length (2008-2015). Although unconventional wells generate less produced water relative to oil ( 3 bbl of water relative to oil) than conventional wells, the main difference is that this produced water cannot be reinjected into the low permeability shale reservoirs. Instead, the produced water is disposed into non-producing geologic zones that could result in overpressuring and induced seismicity. There is a high potential for reusing produced water from unconventional wells in the Permian Basin because the produced water volumes can support the hydraulic fracturing water demand based on 2014 data. Reusing produced water with minimal water treatment (clean brine) could partially mitigate produced water injection concerns while reducing water demand for hydraulic fracturing.

Well-to-refinery emissions and net-energy analysis of China's crude-oil supply

NASA Astrophysics Data System (ADS)

Masnadi, Mohammad S.; El-Houjeiri, Hassan M.; Schunack, Dominik; Li, Yunpo; Roberts, Samori O.; Przesmitzki, Steven; Brandt, Adam R.; Wang, Michael

2018-03-01

Oil is China's second-largest energy source, so it is essential to understand the country's greenhouse gas emissions from crude-oil production. Chinese crude supply is sourced from numerous major global petroleum producers. Here, we use a per-barrel well-to-refinery life-cycle analysis model with data derived from hundreds of public and commercial sources to model the Chinese crude mix and the upstream carbon intensities and energetic productivity of China's crude supply. We generate a carbon-denominated supply curve representing Chinese crude-oil supply from 146 oilfields in 20 countries. The selected fields are estimated to emit between 1.5 and 46.9 g CO2eq MJ-1 of oil, with volume-weighted average emissions of 8.4 g CO2eq MJ-1. These estimates are higher than some existing databases, illustrating the importance of bottom-up models to support life-cycle analysis databases. This study provides quantitative insight into China's energy policy and the economic and environmental implications of China's oil consumption.

Libya: a dynamic Arab oil power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hobbs, M.

1965-06-01

Libya has become the most dynamic oil-producing nation in the world. Less than 4 yr ago, Libya exported only peanuts, olive oil, and hides. Today, in crude-oil production Libya ranks eighth in the world, with daily production of 1.2 million bbl. Twenty-five oil companies hold concessions and have spent $1.3 billion developing reserves. Petroleum has brought new wealth to the country- an estimated $272 million in 1965. Some 2.75 million ft of hole was drilled in 1964, resulting in 97 oil fields and 4 major basins. Lost circulation has been a problem Transportation and communication are difficult in the vastmore » Libyan desert. Water-contaminated crude and high salt content have plagued production. These problems are being solved. With 45 drillings rigs active, crude production is expected to reach 2 million bpd by 1966. Most of the rigs used are trailer-mounted, unitized 8,000-12,000 ft capacity, that have been specially adapted to work in the Sahara. The drilling-completion programs are briefly described.« less

Technical difficulties and solutions of direct transesterification process of microbial oil for biodiesel synthesis.

PubMed

Yousuf, Abu; Khan, Maksudur Rahman; Islam, M Amirul; Wahid, Zularisam Ab; Pirozzi, Domenico

2017-01-01

Microbial oils are considered as alternative to vegetable oils or animal fats as biodiesel feedstock. Microalgae and oleaginous yeast are the main candidates of microbial oil producers' community. However, biodiesel synthesis from these sources is associated with high cost and process complexity. The traditional transesterification method includes several steps such as biomass drying, cell disruption, oil extraction and solvent recovery. Therefore, direct transesterification or in situ transesterification, which combines all the steps in a single reactor, has been suggested to make the process cost effective. Nevertheless, the process is not applicable for large-scale biodiesel production having some difficulties such as high water content of biomass that makes the reaction rate slower and hurdles of cell disruption makes the efficiency of oil extraction lower. Additionally, it requires high heating energy in the solvent extraction and recovery stage. To resolve these difficulties, this review suggests the application of antimicrobial peptides and high electric fields to foster the microbial cell wall disruption.

Chemical enhanced oil recovery (EOR) activities in Indonesia: How it's future

NASA Astrophysics Data System (ADS)

Abdurrahman, Muslim

2017-05-01

Enhanced oil recovery (EOR) is a proven method for increasing oil production in many oil fields in the world. Huge oil remaining in the reservoir after primary and secondary recovery stage are the main reason for developing EOR methods. Approximately of 49.50 billion barrels oil as a candidate for EOR activities in Indonesia. This present study focuses on the chemical EOR activities involved surfactant and polymer. This research based on pertinent information from various resources such as journal papers, conference papers, and report from the government. Based on this information, this paper explain in detail the progress of each project and it shows the potential oil field employ chemical EOR in the near future. Generally, the EOR activities can be categorized into two phases such as preliminary study phase and field implementation phase. In the preliminary study, the activities simply involve experimental and/or simulation works. Following the preliminary is the field implementation phase which can be categorized into three phases such as field trial, pilot project, and full-scale. In fact, several activities have been conducted by Lemigas (government oil and gas research center), Institut Teknologi Bandung, Institut Pertanian Bogor. These activities focused on laboratory and simulation work. Those institutions have been developing the chemical formula collaborating with oil companies for applying the EOR method in their oil fields. Currently, status of chemical EOR activities include 5 oil fields under pilot project and 12 oil fields under field trial. There are 7 oil fields applying surfactant, 4 oil fields by alkaline-surfactant-polymer (ASP), 2 oil fields by polymer, 1 oil field by surfactant polymer (SP), and 1 oil field by caustic. According to this information, we will have insight knowledge about the EOR current activities, the main issues, future activities on chemical EOR in Indonesia. Moreover, this study can became the preliminary information for researchers who interested conducting further research and development on the chemical EOR activities in the near future.

Secondary ferroan dolomite rhombs in oil reservoirs, Chadra Sands, Gialo field, Libya

DOE Office of Scientific and Technical Information (OSTI.GOV)

Al-Shaieb, Z.; Shelton, J.W.

1978-03-01

Oil-productive, Oligocene Chadra sands in Gialo field, Libya, at depths of 600 to 750 m contain small dolomite rhombs. The rhombs are present as single crystals on detrital grains and as nonmosaic aggregates in pore space. The dolomite is calcium-rich and contains up to 10% iron but not measurable sodium or strontium. Total dissolved solids of produced interstitial water from the Chadra sand range from about 4,500 to 10,000 ppM. Introduction of fresh (meteoric) water into the Chadra sands, which were deposited in shallow-marine (shelf) environment, was responsible for formation of the dolomite rhombs. Iron in the dolomite rhombs wasmore » derived from alteration of galuconite.« less

Geochemical Data from Produced Water Contamination Investigations: Osage-Skiatook Petroleum Environmental Research (OSPER) Sites, Osage County, Oklahoma

USGS Publications Warehouse

Thordsen, James J.; Kharaka, Yousif K.; Ambats, Gil; Kakouros, Evangelos; Abbott, Marvin M.

2007-01-01

We report chemical and isotopic analyses of 345 water samples collected from the Osage-Skiatook Petroleum Environmental Research (OSPER) project. Water samples were collected as part of an ongoing multi-year USGS investigation to study the transport, fate, natural attenuation, and ecosystem impacts of inorganic salts and organic compounds present in produced water releases at two oil and gas production sites from an aging petroleum field located in Osage County, in northeast Oklahoma. The water samples were collected primarily from monitoring wells and surface waters at the two research sites, OSPER A (legacy site) and OSPER B (active site), during the period March, 2001 to February, 2005. The data include produced water samples taken from seven active oil wells, one coal-bed methane well and two domestic groundwater wells in the vicinity of the OSPER sites.

Effects of Wastewater from Oil Exploration on Soil Mesofauna.

PubMed

Ferreira, Raimundo N C; Weber, Olmar B; Correia, Maria E F; Benazzi-Ikeda, Eloísa S; Scoriza, Rafael N; Mesquita, Antonio L M

2015-12-01

Wastewater from oil exploration may contain substances that can alter the diversity of soil organisms. This study evaluated whether produced water treated by filtration or reverse osmosis and glutaraldehyde from reverse osmosis treatments negatively affected the mesofauna in an irrigated area. In the field, irrigation with produced water treated by reverse osmosis and filtration influenced Hymenoptera and Cosmochthonius sp., while Entomobryomorpha springtails were affected only by the reverse osmosis water. In the ecotoxicological tests, reproduction in the springtail Folsomia candida was inhibited by the reverse osmosis treatment, while reproduction in the earthworm Enchytraeus crypticus was affected by both water treatments. Although glutaraldehyde did not affect the survival of F. candida, the reproduction was inhibited (EC50 = 44.4 mg/L). No adverse effect of glutaraldehyde was observed on reproduction or survival of E. crypticus. These results indicate that produced water, when used in irrigated agriculture, may affect soil functional mesofauna.

Effects of oil on avian reproduction: A review and discussion

USGS Publications Warehouse

Albers, P.H.; Rosie, Don; Barnes, Stephen N.

1983-01-01

Oil pollution is a highly visible form of environmental contamination that affects avian reproduction in a variety of ways. Plumage oiling causes widespread and locally severe mortality of adult birds. Egg oiling can be a serious hazard for bird embryos but only a few field observationons of this have been reported. Oil ingestion seldom kills birds directly but it causes sublethal change~ in the bodily functions and behavior of adults and nestlings. Studies of the effects of oil on avian reproduction have produced varied and, in ingestion studies, sometimes conflicting results because of inconsistent experimental design and the use of different test species and types of oil. Field experimentation with the sublethal effects of ingested oil on avian reproduction has been limited. Simulation modelling of seabird populations has shown that (l) an occasional decrease in survival of breeding adults will have a greater impact on seabird populations than an occasional decrease in reproductive success, and (2) populations of long-lived seabirds with low reproductive potential have great difficulty recovering from high one-time mortality when experiencing even small sustained annual decreases in either natality or breeding adult survival. The impact of oil-related decreases in survival or reproduction will be more noticeable at the local or colony level than at the regional or species level. Immigration, surplus breeders, and possible compensatory changes in natality and mortality resulting from population reductions usually prevent local population reductions from lasting very long (unless the species is rare or at the edge of its range). A study of west European seabird populations indicates that the natural annual mortality of the region greatly exceeds the annual mortality due to plumage oiling; effects of oil ingestion and egg oiling were not measured but were thought to be less than the mortality from plu~age oiling. Oil-related mortality, even if in addition to expected mortality, would not have a detectable impact on regional populations if environmental conditions were favorable (increased natality, decreased mortality) for the birds.

Influence of fertilizer levels on phytoremediation of crude oil-contaminated soils with the tropical pasture grass Brachiaria brizantha (hochst. ex a. rich.) stapf.

PubMed

Merkl, Nicole; Schultze-Kraft, Rainer; Arias, Marianela

2005-01-01

Determination of fertilizer levels in phytoremediation of petroleum hydrocarbons is a complex issue, since nutrient demands of the plant and of degrading microorganisms in the rhizosphere have to be considered In the present work, three fertilizer levels were tested in a greenhouse experiment with the aim of optimizing growth of the tropical pasture grass Brachiaria brizantha and enhance microbial degradation of heavy crude oil in soil Fertilizer was applied twice in a concentration of 200, 300, and 400 mg each of N, P, and K per kg soil before and after the first sampling (14 wk). The medium fertilizer concentration resulted in best root growth and highest absolute oil dissipation (18.4%) after 22 wk The highest concentration produced best shoot growth and highest relative oil dissipation after 14 wk (10.5% less than unplanted control). In general, degradation of total oil and grease was higher in planted than in unplanted soil, but differences diminished toward the end of the experiment. Next to fertiizer quantity, its composition is an important factor to be further studied, including the form of available nitrogen (N-NO3- vs. N-NH4+). Field trials are considered indispensable for further phytoremediation studies, since greenhouse experiments produce particular water and nutrient conditions.

Excito-repellency of essential oils against an Aedes aegypti (L.) field population in Thailand.

PubMed

Boonyuan, Wasana; Grieco, John P; Bangs, Michael J; Prabaripai, Atchariya; Tantakom, Siripun; Chareonviriyaphap, Theeraphap

2014-06-01

An investigation of the behavioral responses of Aedes aegypti (= Stegomyia aegypti) to various concentrations of essential oils (2.5, 5, and 10%) extracted from hairy basil (Ocimum americanum Linn), ginger (Zingiber officinale Roscoe), lemongrass (Cymbopogon citratus Stapf), citronella grass (Cymbopogon nardus Rendle), and plai (Zingiber cassumunar Roxb) were performed using an excito-repellency test chamber. Results showed that Ae. aegypti exhibited varying levels of escape response in both the contact and noncontact chambers in response to different essential oils. The magnitude of the behaviors changed in a dose-response fashion depending on the percent volume to volume concentration of oil used. A 2.5% concentration of hairy basil oil produced a significantly greater escape response compared to the other extracts at the same concentration (P< 0.05). Oils of ginger, lemongrass, and citronella produced stronger irritant and repellent responses at the median 5% concentration compared to the lowest and highest concentrations. There was marked suppression of escape for both contact and noncontact tests using 10% concentrations of hairy basil, lemongrass, and citronella, with high knockdown for all three oils after 30 min. Hairy basil and lemongrass had the highest insecticidal activity to Ae. aegypti, with LC50 values of 6.3 and 6.7 percent, respectively. We conclude that the essential oils from native plants tested, and likely many other extracts found in plants, have inherent repellent and irritant qualities that should to be screened and optimized for their behavior-modifying properties against Ae. aegypti and other biting arthropods of public health and pest importance. © 2014 The Society for Vector Ecology.

Identification and Evaluation of Fluvial-Dominated Deltaic (Class 1 Oil) Reservoirs in Oklahoma: Yearly technical progress report for January 1-December 31, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Banken, M.K.; Andrews, R.

The Oklahoma Geological Survey (OGS), the Geo Information Systems department, and the School of Petroleum and Geological Engineering at the University of Oklahoma are engaged in a five-year program to identify and address Oklahoma`s oil recovery opportunities in fluvial-dominated deltaic (FDD) reservoirs. This program includes a systematic and comprehensive collection and evaluation of information on all FDD oil reservoirs in Oklahoma and the recovery technologies that have been (or could be) applied to those reservoirs with commercial success. During 1996, three highly successful FDD workshops involving 6 producing formations (4 plays) were completed: (1) Layton and Osage-Layton April 17 (2)more » Prue and Skinner June 19 and 26 (3) Cleveland October 17 (4) Peru October 17 (combined with Cleveland play). Each play was presented individually using the adopted protocol of stratigraphic interpretations, a regional overview, and two or more detailed field studies. The project goal was to have one field study from each play selected for waterflood simulation in order to demonstrate enhanced recovery technologies that can be used to recovery secondary oil. In this effort, software utilized for reservoir simulation included Eclipse and Boast 111. In some cases, because of poor production records and inadequate geologic data, field studies completed in some plays were not suitable for modeling. All of the workshops included regional sandstone trend analysis, updated field boundary identification, a detailed bibliography and author reference map, and detailed field studies. Discussion of general FDD depositional concepts was also given. In addition to the main workshop agenda, the workshops provided computer mapping demonstrations and rock cores with lithologic and facies interpretations. In addition to the workshops, other elements of FDD program were improved during 1996. Most significant was the refinement of NRIS MAPS - a user-friendly computer program designed to access NRIS data and interface with mapping software such as Arc View in order to produce various types of information maps. Most commonly used are well base maps for field studies, lease production maps, and regional maps showing well production codes, formation show codes, well spud dates, and well status codes. These regional maps are valuable in identifying areas of by-passed oil production, field trends, and time periods of development for the various FDD plays in Oklahoma. Besides maps, NRIS MAPS provides data in table format which can be used to generate production decline curves and estimates of cumulative hydrocarbon production for leases and fields. Additionally, many computer-related services were provided by support staff concerning technical training, private consultation, computer mapping, and data acquisition.« less

Microfluidic preparation and self diffusion PFG-NMR analysis of monodisperse water-in-oil-in-water double emulsions.

PubMed

Hughes, Eric; Maan, Abid Aslam; Acquistapace, Simone; Burbidge, Adam; Johns, Michael L; Gunes, Deniz Z; Clausen, Pascal; Syrbe, Axel; Hugo, Julien; Schroen, Karin; Miralles, Vincent; Atkins, Tim; Gray, Richard; Homewood, Philip; Zick, Klaus

2013-01-01

Monodisperse water-in-oil-in-water (WOW) double emulsions have been prepared using microfluidic glass devices designed and built primarily from off the shelf components. The systems were easy to assemble and use. They were capable of producing double emulsions with an outer droplet size from 100 to 40 μm. Depending on how the devices were operated, double emulsions containing either single or multiple water droplets could be produced. Pulsed-field gradient self-diffusion NMR experiments have been performed on the monodisperse water-in-oil-in-water double emulsions to obtain information on the inner water droplet diameter and the distribution of the water in the different phases of the double emulsion. This has been achieved by applying regularization methods to the self-diffusion data. Using these methods the stability of the double emulsions to osmotic pressure imbalance has been followed by observing the change in the size of the inner water droplets over time. Copyright © 2012 Elsevier Inc. All rights reserved.

Characterisation of culture-independent and -dependent microbial communities in a high-temperature offshore chalk petroleum reservoir.

PubMed

Kaster, Krista M; Bonaunet, Kristin; Berland, Harald; Kjeilen-Eilertsen, Grethe; Brakstad, Odd Gunnar

2009-11-01

Recent studies have indicated that oil reservoirs harbour diverse microbial communities. Culture-dependent and culture-independent methods were used to evaluate the microbial diversity in produced water samples of the Ekofisk oil field, a high temperature, and fractured chalk reservoir in the North Sea. DGGE analyses of 16S rRNA gene fragments were used to assess the microbial diversity of both archaeal and bacterial communities in produced water samples and enrichment cultures from 4 different wells (B-08, X-08, X-18 and X-25). Low diversity communities were found when 16S rDNA libraries of bacterial and archaeal assemblages were generated from total community DNA obtained from produced water samples and enrichment cultures. Sequence analysis of the clones indicated close matches to microbes associated with high-temperature oil reservoirs or other similar environments. Sequences were found to be similar to members of the genera Thermotoga, Caminicella, Thermoanaerobacter, Archaeoglobus, Thermococcus, and Methanobulbus. Enrichment cultures obtained from the produced water samples were dominated by sheathed rods. Sequence analyses of the cultures indicated predominance of the genera Petrotoga, Arcobacter, Archaeoglobus and Thermococcus. The communities of both produced water and enrichment cultures appeared to be dominated by thermophilic fermenters capable of reducing sulphur compounds. These results suggest that the biochemical processes in the Ekofisk chalk reservoir are similar to those observed in high-temperature sandstone reservoirs.

7 CFR 985.155 - Identification of oil by producer.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Regulations § 985.155 Identification of oil by producer. Following the distillation of oil and prior to... completion of its distillation. (a) Producer's name and address; (b) Date the oil was put into the drum; (c...

7 CFR 985.155 - Identification of oil by producer.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Regulations § 985.155 Identification of oil by producer. Following the distillation of oil and prior to... completion of its distillation. (a) Producer's name and address; (b) Date the oil was put into the drum; (c...

7 CFR 985.155 - Identification of oil by producer.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Regulations § 985.155 Identification of oil by producer. Following the distillation of oil and prior to... completion of its distillation. (a) Producer's name and address; (b) Date the oil was put into the drum; (c...

7 CFR 985.155 - Identification of oil by producer.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Regulations § 985.155 Identification of oil by producer. Following the distillation of oil and prior to... completion of its distillation. (a) Producer's name and address; (b) Date the oil was put into the drum; (c...

Multivariate analysis relating oil shale geochemical properties to NMR relaxometry

USGS Publications Warehouse

Birdwell, Justin E.; Washburn, Kathryn E.

2015-01-01

Low-field nuclear magnetic resonance (NMR) relaxometry has been used to provide insight into shale composition by separating relaxation responses from the various hydrogen-bearing phases present in shales in a noninvasive way. Previous low-field NMR work using solid-echo methods provided qualitative information on organic constituents associated with raw and pyrolyzed oil shale samples, but uncertainty in the interpretation of longitudinal-transverse (T1–T2) relaxometry correlation results indicated further study was required. Qualitative confirmation of peaks attributed to kerogen in oil shale was achieved by comparing T1–T2 correlation measurements made on oil shale samples to measurements made on kerogen isolated from those shales. Quantitative relationships between T1–T2 correlation data and organic geochemical properties of raw and pyrolyzed oil shales were determined using partial least-squares regression (PLSR). Relaxometry results were also compared to infrared spectra, and the results not only provided further confidence in the organic matter peak interpretations but also confirmed attribution of T1–T2 peaks to clay hydroxyls. In addition, PLSR analysis was applied to correlate relaxometry data to trace element concentrations with good success. The results of this work show that NMR relaxometry measurements using the solid-echo approach produce T1–T2 peak distributions that correlate well with geochemical properties of raw and pyrolyzed oil shales.

Geology and habitat of oil in Ras Budran field, Gulf of Suez, Egypt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chowdhary, L.R.; Taha, S.

1987-10-01

The Ras Budran structure at the deepest mappable seismic reflector, the top of the Kareem Formation (middle Miocene), is a broad northeast-southwest-trending anticlinal feature with an anomalous strike nearly at right angles to the main Gulf of Suez trend. Oil is produced from three units of Nubian Formation sandstone from a depth of 11,000-12,000 ft (3352-3657 m). The lower unit of Paleozoic age averages 10% porosity and has up to 200 md in-situ permeability. Wells completed in this unit produce up to 2000 BOPD. In contrast, the sands to the upper two units of the Early Cretaceous have 15-20% porositymore » and up to 700 md permeability. Wells completed in this unit produce 6000-8000 BOPD. The Ras Budran structure was formed primarily during an intra-Rudeis tectonic phase (lower Miocene). Oil migration for accumulation in the structure started in the late Miocene or Pliocene when the Santonian Brown Limestone and the Eocene Thebes Formation, the main source beds in the Gulf of Suez, reached the threshold of oil generation at a burial depth of approximately 10,000 ft (3048 m). At this depth, the organic matter in the source beds had a high transformation ratio (0.10 to 0.15), high yields of C/sub 15+/ soluble organic matter and C/sub 15+/ saturated hydrocarbons, vitrinite reflectance (R/sub 0/) of 0.62%, and a time-temperature index (TTI) value of 15. Oil migration from mature source beds in adjoining lows into low-potential Nubian reservoirs is easily explained by fault planes that acted as conduits for oil migration. 16 figures, 3 tables.« less

Future for oil and gas in the EEC. I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1974-03-01

This study by UNICE (Union of Industries of the EEC), prepared prior to the October 1973 Mideast conflict, shows remarkable foresight in the light of subsequent events. Of the 3 major industrial units (the U.S., Europe, and Japan), Europe would be in the weakest position in the event of an energy shortage. During the 1973-85 period, the techncal risks threatening the security of Europe's oil supplies are subordinate to the political and economic risks: (1) Certain producing countries may be tempted to use their oil potential as a means of influencing foreign policy by limiting production, (2) international monetary problemsmore » and worldwide inflation may give rise to producer-country reactions which are not confined to the technical field, and (3) the utilization of the vast financial resources of some producer countries may prove a serious problem. UNICE considers it imperative for the EEC, in collaboration with industry and with due regard for the fundamental importance of competition, to arrive at a common energy policy as soon as possible and to take the decisions necessary to ensure the long-term security of energy supplies on satisfactory economic terms. The EEC and the national governments must seek to promote the security of energy supplies in all forms, ensure an adequate profitability level to finance investment, deal more flexibly with environmental problems, adopt a more homogenous attitude, and encourage the development of alternative energy sources. For oil specifically, there are 4 ways of reducing the political and economic risks threatening exploration and production: limiting demand for oil products, increasing energy supplies, facilitating the oil industry's activities, and encouraging action by governments.« less

Reservoir compaction of the Belridge Diatomite and surface subsidence, south Belridge field, Kern County, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowersox, J.R.; Shore, R.A.

1990-05-01

Surface subsidence due to reservoir compaction during production has been observed in many large oil fields. Subsidence is most obvious in coastal and offshore fields where inundation by the sea occurs. Well-known examples are Wilmington field in California and Ekofisk field in the North Sea. In South Belridge field, the Belridge Diatomite member of the late Miocene Reef Ridge Shale has proven prone to compaction during production. The reservoir, a high-porosity, low-permeability, highly compressive rock composed largely of diatomite and mudstone, is about 1,000 ft thick and lies at an average depth of 1,600 ft. Within the Belridge Diatomite, reservoirmore » compaction due to withdrawal of oil and water in Sec. 12, T28S, R20E, MDB and M, was noticed after casing failures in producing wells began occurring and tension cracks, enlarged by hydrocompaction after a heavy rainstorm were observed. Surface subsidence in Sec. 12 has been monitored since April 1987, through the surveying of benchmark monuments. The average annualized subsidence rate during 1987 was {minus}1.86 ft/yr, {minus}0.92 ft/yr during 1988, and {minus}0.65 ft/yr during 1989; the estimated peak subsidence rate reached {minus}7.50 ft/yr in July 1985, after 1.5 yrs of production from the Belridge Diatomite reservoir. Since production from the Belridge Diatomite reservoir commenced in February 1984, the surface of the 160-ac producing area has subsided about 12.5 ft. This equates to an estimated reservoir compaction of 30 ft in the Belridge Diatomite and an average loss of reservoir porosity of 2.4% from 55.2 to 52.8%. Injection of water for reservoir pressure maintenance in the Belridge diatomite began in June 1987, and has been effective in mitigating subsidence to current rates and repressurizing the reservoir to near-initial pressure. An added benefit of water injection has been improved recovery of oil from the Belridge Diatomite by waterflood.« less

Giddings Austin chalk enters deep lean-gas phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moritis, G.

1995-12-25

Deep lean gas is the latest phase in the growth of the Giddings field Austin chalk play. The first phase involved drilling vertical oil and gas wells. Next came the horizontal well boom in the shallower Austin chalk area, which is still continuing. And now this third phase places horizontal laterals in the Austen chalk at about 14,000--15,000 ft to produce lean gas. The article describes the producing wells and gas gathering.

Oil sorbents from plastic wastes and polymers: A review.

PubMed

Saleem, Junaid; Adil Riaz, Muhammad; Gordon, McKay

2018-01-05

A large volume of the waste produced across the world is composed of polymers from plastic wastes such as polyethylene (HDPE or LDPE), polypropylene (PP), and polyethylene terephthalate (PET) amongst others. For years, environmentalists have been looking for various ways to overcome the problems of such large quantities of plastic wastes being disposed of into landfill sites. On the other hand, the usage of synthetic polymers as oil sorbents in particular, polyolefins, including polypropylene (PP) and polyethylene (PE) have been reported. In recent years, the idea of using plastic wastes as the feed for the production of oil sorbents has gained momentum. However, the studies undertaking such feasibility are rather scattered. This review paper is the first of its kind reporting, compiling and reviewing these various processes. The production of an oil sorbent from plastic wastes is being seen to be satisfactorily achievable through a variety of methods Nevertheless, much work needs to be done regarding further investigation of the numerous parameters influencing production yields and sorbent qualities. For example, differences in results are seen due to varying operating conditions, experimental setups, and virgin or waste plastics being used as feeds. The field of producing oil sorbents from plastic wastes is still very open for further research, and seems to be a promising route for both waste reduction, and the synthesis of value-added products such as oil sorbents. In this review, the research related to the production of various oil sorbents based on plastics (plastic waste and virgin polymer) has been discussed. Further oil sorbent efficiency in terms of oil sorption capacity has been described. Copyright © 2017 Elsevier B.V. All rights reserved.

Putting 'international' back in IPEC.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Veil, J. A.

During the previous six annual sessions of the International Petroleum Environmental Conference (IPEC), little attention has been given to international issues. Although the US is clearly a leader in oil field research and regulatory development information is available on interesting projects throughout the world Many participants in IPEC have little exposure to international oil and gas environmental problems and solutions. Beginning with the 7th IPEC, a stronger effort is being made to include international issues in the confidence. This paper describes some of the author's experiences in working with international oil and gas environmental issues in North America, Latin America,more » Europe, and Asia. Among the topics to be discussed are the issues that developing oil and gas-producing nations face and the need for sensitivity to other nation's cultures and legal systems.« less

Cleanup/stimulation of a horizontal wellbore using propellants. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rougeot, J.E.; Lauterbach, K.A.

1993-01-01

This report documents the stimulation/cleanup of a horizontal well bore (Wilson 25) using propellants. The Wilson 25 is a Bartlesville Sand well located in the Flatrock Field, Osage County, Oklahoma. The Wilson 25 was drilled to determine if horizontal drilling could be used as a means to economically recover primary oil that had been left in place in a mostly abandoned oil field because of the adverse effects of water coning. Pump testing of the Wilson 25 horizontal well bore before cleanup or stimulation produced 6 barrels of oil and .84 barrels of water per day. The high percentage ofmore » daily oil production to total daily fluid production indicated that the horizontal well bore had accessed potentially economical oil reserves if the fluid production rate could be increased by performing a cleanup/stimulation treatment. Propellants were selected as an inexpensive means to stimulate and cleanup the near well bore area in a uniform manner. The ignition of a propellant creates a large volume of gas which penetrates the formation, creating numerous short cracks through which hydrocarbons can travel into the well bore. More conventional stimulation/cleanup techniques were either significantly more expensive, less likely to treat uniformly, or could not be confined to the near well bore area. Three different propellant torpedo designs were tested with a total of 304` of horizontal well bore being shot and producible. The initial test shot caused 400` of the horizontal well bore to become plugged off, and subsequently it could not be production tested. The second and third test shots were production tested, with the oil production being increased 458% and 349%, respectively, on a per foot basis. The Wilson 25 results indicate that a propellant shot treatment is an economically viable means to cleanup/stimulate a horizontal well bore.« less

Short-term effects of subchronic low-level hydrogen sulfide exposure on oil field workers.

PubMed

Mousa, Haider Abdul-Lateef

2015-01-01

To investigate the short-term effects of low-level hydrogen sulfide (H2S) exposure on oil field workers. Observational study included 34 patients who work at an oil field. All patients were males with age range of 22-60 years (mean 37 years). The data were collected by systematic questionnaire about symptoms. The inclusion criteria of patients were symptoms related to inhalation of H2S gas in the oil field. The complaints should be frequent and relapsed after each gas exposure and disappeared when there was no gas exposure. Exclusion criteria were the symptoms which experienced with or without H2S exposure. The presence of H2S gas was confirmed by valid gas detector devices. The most frequent presenting symptom was nasal bleeding. It was revealed in 18 patients (52.9%). This followed by pharyngeal bleeding, gum bleeding, and bloody saliva (mouth bleeding) which were encountered in five cases for each complaint (14.7%). Other less frequent presenting symptoms were tongue bleeding, bloody sputum, headache, abdominal colic, pharyngeal soreness, fatigue, and sleepiness. Nasal mucosa was the most vulnerable part to H2S effect. Inhalation of H2S produced upper respiratory tract epithelial damage that led to bleeding from nose, pharynx, gum, tongue, trachea, and bronchi. There were no complaints of asthmatic attack upon exposure to low level of H2S. Sunlight had a significant role in reduction of ambient air H2S level.

Off-shore enhanced oil recovery in the north sea: matching CO_2 demand and supply given uncertain market conditions

NASA Astrophysics Data System (ADS)

Compernolle, Tine; Welkenhuysen, Kris; Huisman, Kuno; Piessens, Kris; Kort, Peter

2015-04-01

Introduction CO2 enhanced oil recovery (CO2-EOR) entails the injection of CO2 in mature oil fields in order to mobilize the oil. In particular, the injected CO2 reduces the oil's viscosity and acts as a propellant, resulting in an increased oil extraction rate (Leach et al., 2011). Given uncertainty in both oil price and CO2 price under the EU ETS system, aim of this study is to analyze under which economic conditions a CO2 exchange can be established between a CO2 supplier (an electricity producer for whom CO2 is a by-product) and a CO2 user (an offshore oil company that exploits oil fields in the North Sea and needs CO2 for enhanced oil recovery). Methodology A techno-economic simulation tool, PSS IV, was developed to provide investment decision support on integrated CO2-EOR projects (Welkenhuysen et al., 2014). Until now, a fixed onshore supply of CO2 was presumed. An economic optimization model is now developed for both the CO2 producer and the CO2 user. Because net present value and discounted cash flow methods are inadequate to deal with issues like uncertainty and the irreversibility of an investment decision, the real options theory is applied (Dixit and Pindyck, 1994). The way in which cooperation between the companies can take place, will be studied using game theoretical concepts (Lukas and Welling, 2014). Economic and technical data on CO2 capture are available from the PSS database (Piessens et al., 2012). Data on EOR performance, CO2 requirements and various costs are taken from literature (BERR, 2007; Klokk et al., 2010; Pershad et al., 2012). Results/Findings It will be shown what the impact of price uncertainty is on the investment decision of the electricity producer to capture and sell CO2, and on the decision of the oil producer to make the necessary investments to inject CO2 for enhanced oil recovery. Based on these results, it will be determined under which economic conditions a CO2 exchange and transport can take place. Furthermore, also the role of the ETS system will be discussed. In an initial stage, only the CO2-price and oil price market uncertainties are considered. In a further stage, uncertainties from the supply side (technology) and EOR (geological) will be added. References BERR. 2007. Development of a CO2 transport and storage network in the North Sea: report to the North Sea Basin Task Force. Dixit A, Pindyck R (1994). Investment under Uncertainty. In, Princeton University Press. Klokk Ø, Schreiner PF, Pagès-Bernaus A, Tomasgard A (2010). Optimizing a CO2 value chain for the Norwegian Continental Shelf. Energy Policy 38(11): 6604-6614 Leach A, Mason CF, Veld Kvt (2011). Co-optimization of enhanced oil recovery and carbon sequestration. Resource Energy Econ 33(4): 893-912 Lukas E, Welling A (2014). Timing and eco(nomic) efficiency of climate-friendly investments in supply chains. Eur J Oper Res 233(2): 448-457 Pershad, H., Durusut, E., Crerar, A., Black, D., Mackay, E. & Oldern, P., 2012. Economic Impacts of CO2-enhanced oil recovery for Scotland, Final report for Scottish Enterprise. Element energy, London. Piessens, K., Welkenhuysen K., Laenen, B., Ferket, H., Nijs, W., Duerinck, J., Cochez, E., Mathieu, Ph., Valentiny, D., Baele, J.-M., Dupont, N. & Hendriks, Ch., 2012. Policy Support System for Carbon Capture and Storage and Collaboration between Belgium-the Netherlands "PSS-CCS", Final report. Belgian Science Policy Office, Research Programme Science for a Sustainable Development contracts SD/CP/04a,b & SD/CP/803, 335p. Welkenhuysen, K., Compernolle, T., Piessens, K., Ramírez, A., Rupert, J. & Swennen, R., 2014. Geological uncertainty and investment risk in CO2-enhanced oil recovery. 12th International Conference on Greenhouse Gas Control Technologies (GHGT-12), Austin, Texas, 05-09/10/2014.

Methods for Assessing the Impact of Fog Oil Smoke on Availability, Palatability, & Food Quality of Relevant Life Stages of Insects for Threatened and Endangered Species

DOE Office of Scientific and Technical Information (OSTI.GOV)

Driver, Crystal J.; Strenge, Dennis L.; Su, Yin-Fong

2007-04-01

A methodology for quantifying population dynamics and food source value of insect fauna in areas subjected to fog oil smoke was developed. Our approach employed an environmentally controlled re-circulating wind tunnel outfitted with a high-heat vaporization and re-condensation fog oil generator that has been shown to produce aerosols of comparable chemistry and droplet-size distribution as those of field releases of the smoke. This method provides reproducible exposures of insects under realistic climatic and environmental conditions to fog oil aerosols that duplicate chemical and droplet-size characteristics of field releases of the smoke. The responses measured take into account reduction in foodmore » sources due to death and to changes in availability of relevant life stages of insects that form the prey base for the listed Threatened and Endangered Species. The influence of key environmental factors, wind speed and canopy structure on these responses were characterized. Data generated using this method was used to develop response functions related to particle size, concentration, wind speed, and canopy structure that will allow military personnel to assess and manage impacts to endangered species from fog oil smoke used in military training.« less

Membrane Lipids as Indicators for Viable Bacterial Communities Inhabiting Petroleum Systems.

PubMed

Gruner, Andrea; Mangelsdorf, Kai; Vieth-Hillebrand, Andrea; Horsfield, Brian; van der Kraan, Geert M; Köhler, Thomas; Janka, Christoph; Morris, Brandon E L; Wilkes, Heinz

2017-08-01

Microbial activity in petroleum reservoirs has been implicated in a suite of detrimental effects including deterioration of petroleum quality, increases in oil sulfur content, biofouling of steel pipelines and other infrastructures, and well plugging. Here, we present a biogeochemical approach, using phospholipid fatty acids (PLFAs), for detecting viable bacteria in petroleum systems. Variations within the bacterial community along water flow paths (producing well, topside facilities, and injection well) can be elucidated in the field using the same technique, as shown here within oil production plants in the Molasse Basin of Upper Austria. The abundance of PLFAs is compared to total cellular numbers, as detected by qPCR of the 16S rDNA gene, to give an overall comparison between the resolutions of both methods in a true field setting. Additionally, the influence of biocide applications on lipid- and DNA-based quantification was investigated. The first oil field, Trattnach, showed significant PLFA abundances and cell numbers within the reservoir and topside facilities. In contrast, the second field (Engenfeld) showed very low PLFA levels overall, likely due to continuous treatment of the topside facilities with a glutaraldehyde-based antimicrobial. In comparison, Trattnach is dosed once per week in a batch fashion. Changes within PLFA compositions across the flow path, throughout the petroleum production plants, point to cellular adaptation within the system and may be linked to shifts in the dominance of certain bacterial types in oil reservoirs versus topside facilities. Overall, PLFA-based monitoring provides a useful tool to assess the abundance and high-level taxonomic diversity of viable microbial populations in oil production wells, topside infrastructure, pipelines, and other related facilities.

Hydrocarbons and heavy metals in fine particulates in oil field air: possible impacts on production of natural silk.

PubMed

Devi, Gitumani; Devi, Arundhuti; Bhattacharyya, Krishna Gopal

2016-02-01

Analyses of fine particulates (PM2.5) from the upper Assam oil fields of India indicated considerable presence of higher hydrocarbons (C22-C35) and heavy metals, Cd, Co, Cr, Cu, Ni, Pb, and Zn. This has raised serious concern for the sustainability of the exotic Muga (Antheraea assama) silk production, which has been a prime activity of a large number of people living in the area. The Muga worm feeds on the leaves of Machilus bombycina plant, and the impacts of air quality on its survival were further investigated by analyzing the leaves of the plant, the plantation soil, and the Muga cocoons. PM2.5 content in the air was much more during the winter due to near calm conditions and high humidity. Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), and gas chromatography-mass spectrometer (GC-MS) analysis of PM2.5 showed the presence of higher alkanes (C22-C35) that could be traced to crude oil. Cr, Ni, and Zn were found in higher concentrations in PM2.5, M. bombycina leaves, and the plantation soil indicating a common origin. The winter has been the best period for production of the silk cocoons, and the unhealthy air during this period is likely to affect the production, which is already reflected in the declining yield of Muga cocoons from the area. SEM and protein analyses of the Muga silk fiber produced in the oil field area have exhibited the deteriorating quality of the silk. This is the first report from India on hydrocarbons and associated metals in PM2.5 collected from an oil field and on their possible effects on production of silk by A. assama.

Environmental impact assessment of oilfield upgrades in Bohai Sea

NASA Astrophysics Data System (ADS)

Chen, Ruihui; Xiong, Yanna; Li, Jiao; Li, Xianbo

2018-02-01

This paper designed 65 environmental monitoring sites to collect samples and analyze for better evaluating the environmental impact generated by cuttings, mud, produced water with oil and oil pollutions that produced during the upgrading in the Bohai Sea where the oil field 34-1 upgraded. Collecting samples include ocean water, marine life and sediments and test items involve PH, dissolved oxygen (DO), salinity, chemical oxygen demand (COD), phosphate, organic carbon, sulfide, inorganic nitrogen, petroleum, copper (Cu), lead (Pb), zinc (Zn), cadmium (Cd), total chromium (Cr), total mercury (Hg) and arsenic (As). Meanwhile sample sites collect and analyze the abundance and diversity of marine plants and elaborated the environmental impact caused by upgrading renovation project from the aspects of sea water, marine life and marine sediments. Through analysis and comparison we found that seawater quality conform the Ш seawater quality standards, the excessive rate of Cu is 10%, the average diversity index of marine life is 2.34 and evenness is 0.68. Influence range of marine sediments and pollutants of production is within 2.68km and basically has no serious impact in the surrounding sea area. It’s worth nothing that reconstruction project has the risk of oil spilling and protective measures must be prepared.

Qaharir Field, Oman: A textbook case

DOE Office of Scientific and Technical Information (OSTI.GOV)

O`Dell, P.M.

1995-12-31

Qaharir Field is located in the southern part of the Sultanate of Oman. Like several fields in South Oman, it produces a light oil with very little solution gas. Qaharir Field contains a large depletion reservoir and several natural water drive reservoirs. There is, therefore, a large variation in the primary recovery efficiencies. A recent petroleum engineering review of this field determined the reservoir drive mechanisms and provided a basis for further development plans. This review of Qaharir Field demonstrates the application of conventional reservoir engineering tools to gain an understanding of the reservoir in sufficient detail to select andmore » plan the next development objectives.« less

Developing a cost effective environmental solution for produced water and creating a ''new'' water resource

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doran, Glenn; Leong, Lawrence Y.C.

2000-05-01

The project goal is to convert a currently usable by-product of oil production, produced water, into a valuable drinking water resource. The project was located at the Placate Oil Field in Santa Clarita, California, approximately 25 miles north of Los Angeles. The project included a literature review of treatment technologies; preliminary bench-scale studies to refine a planning level cost estimate; and a 10-100 gpm pilot study to develop the conceptual design and cost estimate for a 44,000 bpd treatment facility. A reverse osmosis system was constructed, pilot tested, and the data used to develop a conceptual design and operation ofmore » four operational scenarios, two industrial waters levels and two irrigation/potable water.« less

Case history of the Seven Rivers Sand Waterflood, Crockett County, Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riley, E.A.; Bates, T.P.

1965-04-22

The Noelke Field is located approximately 6 1/2 miles SE of Iraan in Crockett County, Texas. The field covers some 2760 proven productive acres with an estimated 1300 acres being oil-productive and the remainder being high enough structurally to carry gas saturation. This report covers only the southern segment. The Noelke field produces from the Seven Rivers sand of the Permian System. The sand is found at depths ranging from 1006 to 1756 ft from the surface. Illustrations show field location, gas cap and oil segments, structure of the southern segment, isopachs, production history of the southern segment, and themore » injection pattern. Initial water injection was realized on Nov. 17, 1957, with all wells taking water readily at zero pressure. Initial flood response was detected in the first well in July 1958, or 8 months after initial injection. The response was positive and significant, reaching 75 bbl oil per day and no water in a month. Production rapidly increased during all of 1959 and reached a peak rate of 2580 bbl in Jan. 1960. Production declined mildly thereafter, and reached a level of 401 bbl during Dec. 1962, then gradually declined thereafter through 1964 to the economic limit. This shallow waterflood project proved highly successful.« less

Faulted shoreline and tidal deposits in the Moenkopi Formation of the Grassy Trail Creek field, Utah

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allison, M.L.; Lutz, S.J.

1991-06-01

The Grassy Trail Creek field produces 40{degrees} API oil and minor gas from shallow marine sandstones of the Triassic Moenkopi Formation on the north-plunging nose of the San Rafael swell in central Utah. Production is controlled by a combination of stratigraphic variations and minor north-south-trending faults. Although fracture permeability enhances production of the reservoir, some faults act as barriers to fluid migration, segmenting the area into productive and dry fault blocks. Horizontal drilling techniques developed in this field in the early 1980s resulted in significantly better production. Log analyses indicate the main reservoir is a complex stack of this thinmore » tidal channel sandstones. Isochore maps of the A and B zones indicate thickened meanders that form localized reservoir pods that are vertically offset. The distribution of isochore thicks appears to represent deposition along a northwest-southeast-trending shoreline fed by sediments from the northeast. There is potential for field extensions in similar deposits along this paleoshoreline. The Moenkopi Formation, long thought to be self-sourcing, may contain oil generated in Precambrian sediments equivalent to the Late Proterozoic Chuar Group. Presence of this older oil would have required migration from Precambrian sedimentary rocks surrounding the San Rafael swell.« less

Petroleum systems of the San Joaquin Basin Province -- geochemical characteristics of gas types: Chapter 10 in Petroleum systems and geologic assessment of oil and gas in the San Joaquin Basin Province, California

USGS Publications Warehouse

Lillis, Paul G.; Warden, Augusta; Claypool, George E.; Magoon, Leslie B.

2008-01-01

The San Joaquin Basin Province is a petroliferous basin filled with predominantly Late Cretaceous to Pliocene-aged sediments, with organic-rich marine rocks of Late Cretaceous, Eocene, and Miocene age providing the source of most of the oil and gas. Previous geochemical studies have focused on the origin of the oil in the province, but the origin of the natural gas has received little attention. To identify and characterize natural gas types in the San Joaquin Basin, 66 gas samples were analyzed and combined with analyses of 15 gas samples from previous studies. For the purpose of this resource assessment, each gas type was assigned to the most likely petroleum system. Three general gas types are identified on the basis of bulk and stable carbon isotopic composition—thermogenic dry (TD), thermogenic wet (TW) and biogenic (B). The thermogenic gas types are further subdivided on the basis of the δ13C values of methane and ethane and nitrogen content into TD-1, TD-2, TD-Mixed, TW-1, TW-2, and TW-Mixed. Gas types TD-1 and TD-Mixed, a mixture of biogenic and TD-1 gases, are produced from gas fields in the northern San Joaquin Basin. Type TD-1 gas most likely originated from the Late Cretaceous to Paleocene Moreno Formation, a gas-prone source rock. The biogenic component of the TD-Mixed gas existed in the trap prior to the influx of thermogenic gas. For the assessment, these gas types were assigned to the Winters- Domengine Total Petroleum System, but subsequent to the assessment were reclassified as part of the Moreno-Nortonville gas system. Dry thermogenic gas produced from oil fields in the southern San Joaquin Basin (TD-2 gas) most likely originated from the oil-prone source rock of Miocene age. These samples have low wetness values due to migration fractionation or biodegradation. The thermogenic wet gas types (TW-1, TW-2, TW-Mixed) are predominantly associated gas produced from oil fields in the southern and central San Joaquin Basin. Type TW-1 gas most likely originates from source rocks within the Eocene Kreyenhagen Formation or the Eocene Tumey formation of Atwill (1935). Type TW-2 gas most likely originates from the Miocene Monterey Formation and equivalents. TW-Mixed gas is likely a mixture of biogenic and wet thermogenic gas (TW-1 or TW-2) derived from source rocks mentioned above. The thermogenic wet gas types are included in the corresponding Eocene or Miocene total petroleum systems. Type B gas is a dry, nonassociated gas produced from the Pliocene San Joaquin Formation in the central and southern San Joaquin Basin. This gas type most likely originated from Pliocene marine source rocks as a product of methanogenesis, and defines the Neogene Nonassociated Gas Total Petroleum System.

Oil palm and the emission of greenhouse gasses- from field measurements in Indonesia

NASA Astrophysics Data System (ADS)

Rahman, Niharika; Bruun, Thilde Bech; Giller, Ken E.; Magid, Jakob; van de Ven, Gerrie; de Neergaard, Andreas

2017-04-01

Palm oil from the oil palm (Elaeis guianensis) has in recent years become the world's most important vegetable oil. The increasing demand for palm oil has led to expansion of oil palm plantations, which has caused environmental controversies associated with carbon losses and the use of large amounts of mineral fertilizers. Efforts to increase sustainability of oil palm cultivation, include recycling of oil-mill residues and pruning's, but with this comes increased potential for methane emission from the plantations. Until now no field-based data on greenhouse gas emissions from oil palm plantations have been reported. Here for the first time we present data from a long term (360 days) field trial in Bah Lias Research Station, North Sumatra, Indonesia on greenhouse gas emissions from an oil palm plantation with various treatments of recycled oil palm waste products, fertilizers and simulated rainfall. The first experiment was conducted over a full year (dry + wet season) with mineral fertilizer treatments including urea and ammonium sulphate, and organic fertilizer treatments constituting: empty fruit bunches (EFB), enriched mulch (EFB + palm oil mill effluent (POME) ) and pruned oil palm fronds (OPF). Treatment doses represent the current management in Indonesian plantations and the higher doses that are expected in the imminent future. For the organic treatments several methods of application (applied in inter-rows, piles, patches or bands) were evaluated. The second experiment investigated effects of soil water saturation on GHG emissions through adding 25 mm simulated rainfall per day for 21 days. Each palm tree received 1 kg of N fertilizer as urea or ammonium sulphate and enriched mulch. The gas fluxes in the fields was measured by a large static-chamber (1.8 m x 1.2 m) method and CH4 and N2O concentrations were determined using gas chromatographs. We found that emissions were significantly affected by the type and dose of mineral fertilizers. Application of urea leads to significantly higher N2O emission than application of ammonium sulphate. Organic fertilizers resulted in significantly higher CH4 emissions than N2O. The combination of enriched mulch and urea produced the highest N2O emission. When applied in piles, organic fertilizers emitted significantly more N2O and CH4 than when spread out. 25 mm simulated rainfall daily resulted in 76% higher N2O emissions than in the control (no water addition) with highest rates day seven after fertilization. This study will contribute to the development of more accountable and sustainable oil palm production systems and help to guide nutrient management practices to slow down or counteract climate change.

Succession in the petroleum reservoir microbiome through an oil field production lifecycle.

PubMed

Vigneron, Adrien; Alsop, Eric B; Lomans, Bartholomeus P; Kyrpides, Nikos C; Head, Ian M; Tsesmetzis, Nicolas

2017-09-01

Subsurface petroleum reservoirs are an important component of the deep biosphere where indigenous microorganisms live under extreme conditions and in isolation from the Earth's surface for millions of years. However, unlike the bulk of the deep biosphere, the petroleum reservoir deep biosphere is subject to extreme anthropogenic perturbation, with the introduction of new electron acceptors, donors and exogenous microbes during oil exploration and production. Despite the fundamental and practical significance of this perturbation, there has never been a systematic evaluation of the ecological changes that occur over the production lifetime of an active offshore petroleum production system. Analysis of the entire Halfdan oil field in the North Sea (32 producing wells in production for 1-15 years) using quantitative PCR, multigenic sequencing, comparative metagenomic and genomic bins reconstruction revealed systematic shifts in microbial community composition and metabolic potential, as well as changing ecological strategies in response to anthropogenic perturbation of the oil field ecosystem, related to length of time in production. The microbial communities were initially dominated by slow growing anaerobes such as members of the Thermotogales and Clostridiales adapted to living on hydrocarbons and complex refractory organic matter. However, as seawater and nitrate injection (used for secondary oil production) delivered oxidants, the microbial community composition progressively changed to fast growing opportunists such as members of the Deferribacteres, Delta-, Epsilon- and Gammaproteobacteria, with energetically more favorable metabolism (for example, nitrate reduction, H 2 S, sulfide and sulfur oxidation). This perturbation has profound consequences for understanding the microbial ecology of the system and is of considerable practical importance as it promotes detrimental processes such as reservoir souring and metal corrosion. These findings provide a new conceptual framework for understanding the petroleum reservoir biosphere and have consequences for developing strategies to manage microbiological problems in the oil industry.

Geology and oil and gas assessment of the Mancos-Menefee Composite Total Petroleum System: Chapter 4 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

USGS Publications Warehouse

Ridgley, J.L.; Condon, S.M.; Hatch, J.R.

2013-01-01

Eight assessment units were defined in the Mancos-Menefee Composite TPS. Of the eight assessment units, four were assessed as conventional oil or gas accumulations and four as continuous-type accumulations. The conventional assessment units are Dakota-Greenhorn Conventional Oil and Gas Assessment Unit (AU), Gallup Sandstone Conventional Oil and Gas AU, Mancos Sandstones Conventional Oil AU, and the Mesaverde Updip Conventional Oil AU. Continuous-type assessments are Dakota-Greenhorn Continuous Gas AU, Mancos Sandstones Continuous Gas AU, Mesaverde Central-Basin Continuous Gas AU, and Menefee Coalbed Gas AU. The Mesaverde Updip Conventional AU was not quantitatively assessed for undiscovered oil and gas resources, because the producing oil fields were smaller than the 0.5 million barrel cutoff, and the potential of finding fields above this cutoff was considered to be low. Total oil resources that have the potential for additions to reserves in the next 30 years are estimated at a mean of 16.78 million barrels. Most of this resource will come from reservoirs in the Mancos Sandstones Oil AU. Gas resources that have the potential for additions to reserves in the next 30 years are estimated at a mean of 11.11 trillion cubic feet of gas (TCFG). Of this amount, 11.03 TCFG will come from continuous gas accumulations; the remainder will be gas associated with oil in conventional accumulations.Total natural gas liquids (NGL) that have the potential for additions to reserves in the next 30 years are estimated at a mean of 99.86 million barrels. Of this amount, 96.95 million barrels will come from the continuous gas assessment units, and 78.3 percent of this potential resource will come from the Mancos Sandstones Continuous Gas AU.

Upper cretaceous (Austin Group) volcanic deposits as a hydrocarbon trap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hutchinson, P.J.

1994-12-31

An Upper Cretaceous submarine igneous extrusion occurs in the subsurface of southwestern Wilson County, Texas. The Coniacian-Santonian-aged (Austin Group) volcanic eruption discharged large volumes of magnetite-rich olivine nephelinite that upon quenching formed an extensive nontronitic clay layer. This clay deposit formed a trapping mechanism for hydrocarbon beneath the volcano. Production from volcanic plugs is normally attributed to the shoal-water carbonate facies developed on top of the volcanic, the palagonite tuff ({open_quotes}serpentine{close_quotes}), and overlying sandstones. The heat energy of the volcano may have thermally matured the calcarous sediments of adjacent parts of the Austin Chalk. The normally grayish-colored suggesting thermal alteration.more » The overlying nontronite trapped mobile hydrocarbons, and this early emplacement of oil may have preserved some of the original porosity and permeability of the Austin Chalk. Austin Chalk-aged volcanic deposits produce hydrocarbons from stratigraphic traps within the volcanic material, within the porous beachrock, and structurally within overlying sandstones. The intruded Austin Chalk also behaves as a reservoir because the original porosity and permeability are maintained by early emplacement of oil and the overlying volcanic clay acts as a seal by preventing vertical migration. Marcelina Creek field, discovered in 1980 from an {open_quotes}augen{close_quotes}-shaped seismic signature and an aerial magnetic survey, produces from the fractured chalk beneath the nontronitic clay layer. This field has produced more than 15 million barrels of oil from more than 60 wells in fractured and porous rock beneath the volcano.« less

The potential of indigenous Paenibacillus ehimensis BS1 for recovering heavy crude oil by biotransformation to light fractions

PubMed Central

Shibulal, Biji; Al-Bahry, Saif N.; Al-Wahaibi, Yahya M.; Elshafie, Abdulkadir E.; Al-Bemani, Ali S.; Joshi, Sanket J.

2017-01-01

Microbial Enhanced Oil Recovery (MEOR) is a potential technology for residual heavy oil recovery. Many heavy oil fields in Oman and elsewhere have difficulty in crude oil recovery because it is expensive due to its high viscosity. Indigenous microbes are capable of improving the fluidity of heavy oil, by changing its high viscosity and producing lighter oil fractions. Many spore-forming bacteria were isolated from soil samples collected from oil fields in Oman. Among the isolates, an autochthonous spore-forming bacterium was found to enhance heavy oil recovery, which was identified by 16S rDNA sequencing as Paenibacillus ehimensis BS1. The isolate showed maximum growth at high heavy oil concentrations within four days of incubation. Biotransformation of heavy crude oil to light aliphatic and aromatic compounds and its potential in EOR was analyzed under aerobic and anaerobic reservoir conditions. The isolates were grown aerobically in Bushnell-Haas medium with 1% (w/v) heavy crude oil. The crude oil analyzed by GC-MS showed a significant biotransformation from the ninth day of incubation under aerobic conditions. The total biotransformation of heavy crude oil was 67.1% with 45.9% in aliphatic and 85.3% in aromatic fractions. Core flooding experiments were carried out by injecting the isolates in brine supplemented with Bushnell-Haas medium into Berea sandstone cores and were incubated for twelve days under oil reservoir conditions (50°C). The extra recovered oil was analyzed by GC-MS. The residual oil recovered from core flood experiments ranged between 10–13% compared to the control experiment. The GC-MS analyses of the extra recovered oil showed 38.99% biotransformation of heavy to light oil. The results also indicated the presence of 22.9% extra aliphatic compounds in the residual crude oil recovered compared to that of a control. The most abundant compound in the extra recovered crude oil was identified as 1-bromoeicosane. The investigations showed the potential of P. ehimensis BS1 in MEOR technology by the biotransformation of heavy to lighter crude oil under aerobic and reservoir conditions. Heavy oil recovery and biotransformation to lighter components are of great economic value and a few studies have been done. PMID:28196087

The oil fields of Allen County, Kentucky, with notes on the oil geology of adjoining counties

USGS Publications Warehouse

Shaw, Eugene Wesley; Mather, Kirtley F.

1919-01-01

This report is based on a reconnaissance investigation of the oil field of Allen County, Ky., which was part of a broader study of the oil and gas fields of Kentucky, Tennessee, and Alabama, on which a general report is planned. Most of the field work was done by Mr. Mather, who spent three and a half weeks in and around the county. Mr. Shaw visited Scottsville, the county seat of Allen County, a few years ago and spent a few days in that vicinity at the beginning of the recent field work, which extended from the middle of April to the middle of May, 1917 He prepared also the first draft of the report and reviewed the literature, including reports in oil and gas journals.The purpose of the field work was to investigate the geology of the county, particularly the structure or lay of the oil-bearing strata and the results of drilling to date. Structural conditions in the producing fields were determined by running level lines to the wells and correlating the data recorded in the well logs generously furnished by the operators. Traverses were made of outcrops, and observations of the dip and strike were made in different parts of the county. Lack of a topographic base map and of time and funds for making an accurate topographic survey render the results of the work somewhat incomplete, but it is hoped they will form a valuable contribution to the knowledge of the geology of this relatively little known region, for little detailed geologic work has been done heretofore within 50 miles of Scottsville.The dips are generally too low to be read by the clinometer, but in some localities unmistakable dips can be observed in extensive outcrops along creek banks and can be measured with a level or hand transit. Few of the beds of this region can be followed any considerable distance, though by means of fossils the stratigraphic position of beds outcropping many miles apart can be determined within a few feet. The black shale is the best horizon marker, but it outcrops in only a few places and is reached in only a few wells outside the oil fields.The field work thus consisted largely in observations on out-, cropping beds in different localities and in estimating the altitude of those identified, in collecting fossils for use in future detailed work, and in obtaining from oil operators data concerning the wells and their output. It included the determination of the general lay of the rocks in the county and surrounding territory and details of structure in certain areas. The rocks lie so nearly flat that without topographic data only the general dip could be made out for a large part of the area examined. A complete set of logs of wildcat wells in the region would have thrown much light on the structure and oil possibilities, but little is known of many of the earlier wells drilled in the region, especially of those altogether unsuccessful. An unsuccessful test is soon forgotten, though the data thus obtained concerning the depth at which different beds were found and the yield of porous strata, whether water, oil, or gas, is of great value to the geologist and oil prospector.

Recycling used palm oil and used engine oil to produce white bio oil, bio petroleum diesel and heavy fuel

NASA Astrophysics Data System (ADS)

Al-abbas, Mustafa Hamid; Ibrahim, Wan Aini Wan; Sanagi, Mohd. Marsin

2012-09-01

Recycling waste materials produced in our daily life is considered as an additional resource of a wide range of materials and it conserves the environment. Used engine oil and used cooking oil are two oils disposed off in large quantities as a by-product of our daily life. This study aims at providing white bio oil, bio petroleum diesel and heavy fuel from the disposed oils. Toxic organic materials suspected to be present in the used engine oil were separated using vacuum column chromatography to reduce the time needed for the separation process and to avoid solvent usage. The compounds separated were detected by gas chromatography-mass spectrometry (GC-MS) and found to contain toxic aromatic carboxylic acids. Used cooking oils (thermally cracked from usage) were collected and separated by vacuum column chromatography. White bio oil produced was examined by GC-MS. The white bio oil consists of non-toxic hydrocarbons and is found to be a good alternative to white mineral oil which is significantly used in food industry, cosmetics and drugs with the risk of containing polycyclic aromatic compounds which are carcinogenic and toxic. Different portions of the used cooking oil and used engine were mixed to produce several blends for use as heavy oil fuels. White bio oil was used to produce bio petroleum diesel by blending it with petroleum diesel and kerosene. The bio petroleum diesel produced passed the PETRONAS flash point and viscosity specification test. The heat of combustion of the two blends of heavy fuel produced was measured and one of the blends was burned to demonstrate its burning ability. Higher heat of combustion was obtained from the blend containing greater proportion of used engine oil. This study has provided a successful recycled alternative for white bio oil, bio petroleum fuel and diesel which can be an energy source.

TREATMENT OF PRODUCED OIL AND GAS WATERS WITH SURFACTANT-MODIFIED ZEOLITE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lynn E. Katz; R.S. Bowman; E.J. Sullivan

2003-11-01

Co-produced water from the oil and gas industry accounts for a significant waste stream in the United States. It is by some estimates the largest single waste stream in the country, aside from nonhazardous industrial wastes. Characteristics of produced water include high total dissolved solids content, dissolved organic constituents such as benzene and toluene, an oil and grease component, and chemicals added during the oil-production process. While most of the produced water is disposed via reinjection, some must be treated to remove organic constituents before the water is discharged. Current treatment options are successful in reducing the organic content; however,more » they cannot always meet the levels of current or proposed regulations for discharged water. Therefore, an efficient, cost-effective treatment technology is needed. Surfactant-modified zeolite (SMZ) has been used successfully to treat contaminated ground water for organic and inorganic constituents. In addition, the low cost of natural zeolites makes their use attractive in water-treatment applications. This report summarizes the work and results of this four-year project. We tested the effectiveness of surfactant-modified zeolite (SMZ) for removal of BTEX with batch and column experiments using waters with BTEX concentrations that are comparable to those of produced waters. The data from our experimental investigations showed that BTEX sorption to SMZ can be described by a linear isotherm model, and competitive effects between compounds were not significant. The SMZ can be readily regenerated using air stripping. We field-tested a prototype SMZ-based water treatment system at produced water treatment facilities and found that the SMZ successfully removes BTEX from produced waters as predicted by laboratory studies. When compared to other existing treatment technologies, the cost of the SMZ system is very competitive. Furthermore, the SMZ system is relatively compact, does not require the storage of potentially hazardous chemicals, and could be readily adapted to an automated system.« less

Laboratory batch experiments and geochemical modelling of water-rock-supercritical CO2 reactions in Southern San Joaquin Valley, California oil field sediments: Implications for future carbon capture and sequestration projects.

NASA Astrophysics Data System (ADS)

Mickler, P. J.; Rivas, C.; Freeman, S.; Tan, T. W.; Baron, D.; Horton, R. A.

2015-12-01

Storage of CO2 as supercritical liquid in oil reservoirs has been proposed for enhanced oil recovery and a way to lower atmospheric CO2 levels. The fate of CO2 after injection requires an understanding of mineral dissolution/precipitation reactions occurring between the formation minerals and the existing formation brines at formation temperatures and pressures in the presence of supercritical CO2. In this study, core samples from three potential storage formations, the Vedder Fm. (Rio Bravo oil field), Stevens Fm. (Elk Hills oil field) and Temblor Fm. (McKittrick oil field) were reacted with a synthetic brine and CO2(sc) at reservoir temperature (110°C) and pressure (245-250 bar). A combination of petrographic, SEM-EDS and XRD analyses, brine chemistry, and PHREEQ-C modelling were used to identify geochemical reactions altering aquifer mineralogy. XRD and petrographic analyses identified potentially reactive minerals including calcite and dolomite (~2%), pyrite (~1%), and feldspars (~25-60%). Despite the low abundance, calcite dissolution and pyrite oxidation were dominant geochemical reactions. Feldspar weathering produced release rates ~1-2 orders of magnitude slower than calcite dissolution. Calcite dissolution increased the aqueous concentrations of Ca, HCO3, Mg, Mn and Sr. Silicate weathering increased the aqueous concentrations of Si and K. Plagioclase weathering likely increased aqueous Ca concentrations. Pyrite oxidation, despite attempts to remove O2 from the experiment, increased the aqueous concentration of Fe and SO4. SEM-EDS analysis of post-reaction samples identified mixed-layered illite-smectites associated with feldspar grains suggesting clay mineral precipitation in addition to calcite, pyrite and feldspar dissolution. The Vedder Fm. sample underwent complete disaggregation during the reaction due to cement dissolution. This may adversely affect Vedder Formation CCS projects by impacting injection well integrity.

Numerical simulation on ferrofluid flow in fractured porous media based on discrete-fracture model

NASA Astrophysics Data System (ADS)

Huang, Tao; Yao, Jun; Huang, Zhaoqin; Yin, Xiaolong; Xie, Haojun; Zhang, Jianguang

2017-06-01

Water flooding is an efficient approach to maintain reservoir pressure and has been widely used to enhance oil recovery. However, preferential water pathways such as fractures can significantly decrease the sweep efficiency. Therefore, the utilization ratio of injected water is seriously affected. How to develop new flooding technology to further improve the oil recovery in this situation is a pressing problem. For the past few years, controllable ferrofluid has caused the extensive concern in oil industry as a new functional material. In the presence of a gradient in the magnetic field strength, a magnetic body force is produced on the ferrofluid so that the attractive magnetic forces allow the ferrofluid to be manipulated to flow in any desired direction through the control of the external magnetic field. In view of these properties, the potential application of using the ferrofluid as a new kind of displacing fluid for flooding in fractured porous media is been studied in this paper for the first time. Considering the physical process of the mobilization of ferrofluid through porous media by arrangement of strong external magnetic fields, the magnetic body force was introduced into the Darcy equation and deals with fractures based on the discrete-fracture model. The fully implicit finite volume method is used to solve mathematical model and the validity and accuracy of numerical simulation, which is demonstrated through an experiment with ferrofluid flowing in a single fractured oil-saturated sand in a 2-D horizontal cell. At last, the water flooding and ferrofluid flooding in a complex fractured porous media have been studied. The results showed that the ferrofluid can be manipulated to flow in desired direction through control of the external magnetic field, so that using ferrofluid for flooding can raise the scope of the whole displacement. As a consequence, the oil recovery has been greatly improved in comparison to water flooding. Thus, the ferrofluid flooding is a large potential method for enhanced oil recovery in the future.

Improvement of Carbon Dioxide Sweep Efficiency by Utilization of Microbial Permeability Profile Modification to Reduce the Amount of Oil Bypassed During Carbon Dioxide Flood

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmitz, Darrel; Brown, Lewis; Lynch, F. Leo

2010-12-31

The objective of this project was to couple microbial permeability profile modification (MPPM), with carbon dioxide flooding to improve oil recovery from the Upper Cretaceous Little Creek Oil Field situated in Lincoln and Pike counties, MS. This study determined that MPPM technology, which improves production by utilizing environmentally friendly nutrient solutions to simulate the growth of the indigenous microflora in the most permeable zones of the reservoir thus diverting production to less permeable, previously unswept zones, increased oil production without interfering with the carbon dioxide flooding operation. Laboratory tests determined that no microorganisms were produced in formation waters, but weremore » present in cores. Perhaps the single most significant contribution of this study is the demonstration that microorganisms are active at a formation temperature of 115°C (239°F) by using a specially designed culturing device. Laboratory tests were employed to simulate the MPPM process by demonstrating that microorganisms could be activated with the resulting production of oil in coreflood tests performed in the presence of carbon dioxide at 66°C (the highest temperature that could be employed in the coreflood facility). Geological assessment determined significant heterogeneity in the Eutaw Formation, and documented relatively thin, variably-lithified, well-laminated sandstone interbedded with heavily-bioturbated, clay-rich sandstone and shale. Live core samples of the Upper Cretaceous Eutaw Formation from the Heidelberg Field, MS were quantitatively assessed using SEM, and showed that during MPPM permeability modification occurs ubiquitously within pore and throat spaces of 10-20 μm diameter. Testing of the MPPM procedure in the Little Creek Field showed a significant increase in production occurred in two of the five production test wells; furthermore, the decline curve in each of the production wells became noticeably less steep. This project greatly extends the number of oil fields in which MPPM can be implemented.« less

Regional resource depletion and industry activity: The case of oil and gas in the Gulf of Mexico

USGS Publications Warehouse

Attanasi, E.D.

1986-01-01

Stable and declining oil and gas prices have changed the industry's price expectations and, along with depletion of promising exploration prospects, has resulted in reduced exploration. Even with intensive additional exploration, production in most U.S. areas is expected to decline. What does this imply for the drilling and petroleum industry suppliers in particular regions? How should planners in government and the private sector project and incorporate the consequences of these changes in their strategies? This paper answers these questions for the industry operating in the offshore Gulf of Mexico. Future oil and gas production, as well as demand for offshore drilling and production facilities, are shown to depend on the size distribution of undiscovered fields, their associated production costs, and oil and gas prices. Declining well productivity is a consequence of development of progressively smaller fields so that long-run drilling demand should not decline in proportion to the expected production decline. Calculations show a substantial payoff to the drilling industry, in terms of potential demand increases, if it can develop and implement cost reducing technologies. Implications of these results for other offshore producing areas such as the North Sea are also discussed. ?? 1986.

Oil field management system

DOEpatents

Fincke, James R.

2003-09-23

Oil field management systems and methods for managing operation of one or more wells producing a high void fraction multiphase flow. The system includes a differential pressure flow meter which samples pressure readings at various points of interest throughout the system and uses pressure differentials derived from the pressure readings to determine gas and liquid phase mass flow rates of the high void fraction multiphase flow. One or both of the gas and liquid phase mass flow rates are then compared with predetermined criteria. In the event such mass flow rates satisfy the predetermined criteria, a well control system implements a correlating adjustment action respecting the multiphase flow. In this way, various parameters regarding the high void fraction multiphase flow are used as control inputs to the well control system and thus facilitate management of well operations.

Isolation and Characterization of Strains CVO and FWKO B, Two Novel Nitrate-Reducing, Sulfide-Oxidizing Bacteria Isolated from Oil Field Brine

PubMed Central

Gevertz, Diane; Telang, Anita J.; Voordouw, Gerrit; Jenneman, Gary E.

2000-01-01

Bacterial strains CVO and FWKO B were isolated from produced brine at the Coleville oil field in Saskatchewan, Canada. Both strains are obligate chemolithotrophs, with hydrogen, formate, and sulfide serving as the only known energy sources for FWKO B, whereas sulfide and elemental sulfur are the only known electron donors for CVO. Neither strain uses thiosulfate as an energy source. Both strains are microaerophiles (1% O2). In addition, CVO grows by denitrification of nitrate or nitrite whereas FWKO B reduces nitrate only to nitrite. Elemental sulfur is the sole product of sulfide oxidation by FWKO B, while CVO produces either elemental sulfur or sulfate, depending on the initial concentration of sulfide. Both strains are capable of growth under strictly autotrophic conditions, but CVO uses acetate as well as CO2 as its sole carbon source. Neither strain reduces sulfate; however, FWKO B reduces sulfur and displays chemolithoautotrophic growth in the presence of elemental sulfur, hydrogen, and CO2. Both strains grow at temperatures between 5 and 40°C. CVO is capable of growth at NaCl concentrations as high as 7%. The present 16s rRNA analysis suggests that both strains are members of the epsilon subdivision of the division Proteobacteria, with CVO most closely related to Thiomicrospira denitrifcans and FWKO B most closely related to members of the genus Arcobacter. The isolation of these two novel chemolithotrophic sulfur bacteria from oil field brine suggests the presence of a subterranean sulfur cycle driven entirely by hydrogen, carbon dioxide, and nitrate. PMID:10831429

Chapter 3: Geologic Assessment of Undiscovered Oil and Gas Resources in the Phosphoria Total Petroleum System of the Wind River Basin Province, Wyoming

USGS Publications Warehouse

Kirschbaum, M.A.; Lillis, P.G.; Roberts, L.N.R.

2007-01-01

The Phosphoria Total Petroleum System (TPS) encompasses the entire Wind River Basin Province, an area of 4.7 million acres in central Wyoming. The source rocks most likely are black, organic-rich shales of the Meade Peak and Retort Phosphatic Shale Members of the Permian Phosphoria Formation located in the Wyoming and Idaho thrust belt to the west and southwest of the province. Petroleum was generated and expelled during Jurassic and Cretaceous time in westernmost Wyoming and is interpreted to have migrated into the province through carrier beds of the Pennsylvanian Tensleep Sandstone where it was preserved in hypothesized regional stratigraphic traps in the Tensleep and Permian Park City Formation. Secondary migration occurred during the development of structural traps associated with the Laramide orogeny. The main reservoirs are in the Tensleep Sandstone and Park City Formation and minor reservoirs are in the Mississippian Madison Limestone, Mississippian-Pennsylvanian Amsden Formation, Triassic Chugwater Group, and Jurassic Nugget Sandstone and Sundance Formation. The traps are sealed by shale or evaporite beds of the Park City, Amsden, and Triassic Dinwoody Formations, Triassic Chugwater Group, and Jurassic Gypsum Spring Formation. A single conventional oil and gas assessment unit (AU), the Tensleep-Park City AU, was defined for the Phosphoria TPS. Both the AU and TPS cover the entire Wind River Basin Province. Oil is produced from 18 anticlinal fields, the last of which was discovered in 1957, and the possibility of discovering new structural oil accumulations is considered to be relatively low. Nonassociated gas is produced from only two fields, but may be underexplored in the province. The discovery of new gas is more promising, but will be from deep structures. The bulk of new oil and gas accumulations is dependent on the discovery of hypothesized stratigraphic traps in isolated carbonate reservoirs of the Park City Formation. Mean resource estimates for the Tensleep-Park City Conventional Oil and Gas AU total 18 million barrels of oil, 294 billion cubic feet of gas, and 5.9 million barrels of natural gas liquids.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas Chidsey

The Mississippian (late Kinderhookian to early Meramecian) Leadville Limestone is a shallow, open-marine, carbonate-shelf deposit. The Leadville has produced over 53 million barrels (8.4 million m{sup 3}) of oil/condensate from seven fields in the Paradox fold and fault belt of the Paradox Basin, Utah and Colorado. The environmentally sensitive, 7500-square-mile (19,400 km{sup 2}) area that makes up the fold and fault belt is relatively unexplored. Only independent producers operate and continue to hunt for Leadville oil targets in the region. The overall goal of this study is to assist these independents by (1) developing and demonstrating techniques and exploration methodsmore » never tried on the Leadville Limestone, (2) targeting areas for exploration, (3) increasing deliverability from new and old Leadville fields through detailed reservoir characterization, (4) reducing exploration costs and risk especially in environmentally sensitive areas, and (5) adding new oil discoveries and reserves. The final results will hopefully reduce exploration costs and risks, especially in environmentally sensitive areas, and add new oil discoveries and reserves. The study consists of three sections: (1) description of lithofacies and diagenetic history of the Leadville at Lisbon field, San Juan County, Utah, (2) methodology and results of a surface geochemical survey conducted over the Lisbon and Lightning Draw Southeast fields (and areas in between) and identification of oil-prone areas using epifluorescence in well cuttings from regional wells, and (3) determination of regional lithofacies, description of modern and outcrop depositional analogs, and estimation of potential oil migration directions (evaluating the middle Paleozoic hydrodynamic pressure regime and water chemistry). Leadville lithofacies at Libon field include open marine (crinoidal banks or shoals and Waulsortian-type buildups), oolitic and peloid shoals, and middle shelf. Rock units with open-marine and restricted-marine facies constitute a significant reservoir potential, having both effective porosity and permeability when dissolution of skeletal grains, followed by dolomitization, has occurred. Two major types of diagenetic dolomite are observed in the Leadville Limestone at Lisbon field: (1) tight 'early' dolomite consisting of very fine grained (<5 {micro}m), interlocking crystals that faithfully preserve depositional fabrics; and (2) porous, coarser (>100-250 {micro}m), rhombic and saddle crystals that discordantly replace limestone and earlier very fine grained dolomite. Predating or concomitant with late dolomite formation are pervasive leaching episodes that produced vugs and extensive microporosity. Most reservoir rocks within Lisbon field appear to be associated with the second, late type of dolomitization and associated leaching events. Other diagenetic products include pyrobitumen, syntaxial cement, sulfide minerals, anhydrite cement and replacement, and late macrocalcite. Fracturing (solution enlarged) and brecciation (autobrecciation) caused by hydrofracturing are widespread within Lisbon field. Sediment-filled cavities, related to karstification of the exposed Leadville, are present in the upper third of the formation. Pyrobitumen and sulfide minerals appear to coat most crystal faces of the rhombic and saddle dolomites. The fluid inclusion and mineral relationships suggest the following sequence of events: (1) dolomite precipitation, (2) anhydrite deposition, (3) anhydrite dissolution and quartz precipitation, (4) dolomite dissolution and late calcite precipitation, (5) trapping of a mobile oil phase, and (6) formation of bitumen. Fluid inclusions in calcite and dolomite display variable liquid to vapor ratios suggesting reequilibration at elevated temperatures (50 C). Fluid salinities exceed 10 weight percent NaCl equivalent. Low ice melting temperatures of quartz- and calcite-hosted inclusions suggest chemically complex Ca-Mg-bearing brines associated with evaporite deposits were responsible for mineral deposition. The overall conclusion from these analyses indicates late dolomitization, saddle dolomite, and dolomite cement precipitation, as well as sulfides and brecciation, may have developed from hydrothermal events that can greatly improve reservoir quality. The result can be the formation of large, diagenetic-type, hydrocarbon traps. The reservoir characteristics, particularly diagenetic overprinting and history, can be applied regionally to other fields and exploration trends in the Paradox Basin. Stable carbon and oxygen isotope data indicate that all Lisbon field Leadville dolomites were likely associated with brines whose composition was enriched in {sup 18}O compared with Late Mississippian seawater. The Leadville replacement dolomite's temperatures of precipitation ranged from about 140 to 194 F ({approx} 60 to 90 C). Saddle dolomite cements were precipitated at temperatures greater than 194 F (>90 C).« less

Application of bioflocculating property of Pseudomonas aeruginosa strain IASST201 in treatment of oil-field formation water.

PubMed

Pathak, Mihirjyoti; Devi, Arundhuti; Sarma, Hridip Kumar; Lal, Banwari

2014-07-01

A bioflocculating activity of 89.8% was depicted by an activated sludge-borne bacteria Pseudomonas aeruginosa strain IASST201 with a yield of bioflocculant of 2.68 g L(-1) obtained from production media broth after optimization of different parameters. The highest bioflocculation efficiency was found at the pre-stationary phase of the bacterial growth period in the production media broth at 96th hour examined from a growth-flocculation kinetics study. 85.67% of bioflocculation was observed in oil-field formation water, with a separation of 68.7% of aliphatic hydrocarbon contents of the formation water after the application of the bacterial bioflocculant by entrapment mechanism with formation of flocs which was analyzed and examined comparatively through gas-chromatography. Extensive removal of heavy metal contents of the oil-field formation water due to bioflocculation was estimated by Atomic Absorption Spectrophotometer (AAS). The SEM and AFM studies declare the extracellular polymeric nature of the bioflocculant produced by this bacterium clumped within bacterial biofilm supported with FTIR study of the extracted bioflocculant. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

13 CFR 315.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... drilling for oil or natural gas, or otherwise produces oil or natural gas, shall be considered to be producing articles directly competitive with imports of oil and with imports of natural gas. Firm means an... fishing, agricultural or service sector entities and those which explore, drill or otherwise produce oil...

Palm oil mill effluent treatment and utilization to ensure the sustainability of palm oil industries.

PubMed

Hasanudin, U; Sugiharto, R; Haryanto, A; Setiadi, T; Fujie, K

2015-01-01

The purpose of this study was to evaluate the current condition of palm oil mill effluent (POME) treatment and utilization and to propose alternative scenarios to improve the sustainability of palm oil industries. The research was conducted through field survey at some palm oil mills in Indonesia, in which different waste management systems were used. Laboratory experiment was also carried out using a 5 m(3) pilot-scale wet anaerobic digester. Currently, POME is treated through anaerobic digestion without or with methane capture followed by utilization of treated POME as liquid fertilizer or further treatment (aerobic process) to fulfill the wastewater quality standard. A methane capturing system was estimated to successfully produce renewable energy of about 25.4-40.7 kWh/ton of fresh fruit bunches (FFBs) and reduce greenhouse gas (GHG) emissions by about 109.41-175.35 kgCO2e/tonFFB (CO2e: carbon dioxide equivalent). Utilization of treated POME as liquid fertilizer increased FFB production by about 13%. A palm oil mill with 45 ton FFB/hour capacity has potential to generate about 0.95-1.52 MW of electricity. Coupling the POME-based biogas digester and anaerobic co-composting of empty fruit bunches (EFBs) is capable of adding another 0.93 MW. The utilization of POME and EFB not only increases the added value of POME and EFB by producing renewable energy, compost, and liquid fertilizer, but also lowers environmental burden.

40 CFR 147.102 - Aquifer exemptions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... than the indicated depths below the ground surface, and described by a 1/4 mile area beyond and lying directly below the following oil and gas producing fields: (i) Swanson River Field—1700 feet. (ii) Beaver Creek Field—1650 feet. (iii) Kenai Gas Field—1300 feet. (2) The portion of aquifers beneath Cook Inlet...

40 CFR 147.102 - Aquifer exemptions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... than the indicated depths below the ground surface, and described by a 1/4 mile area beyond and lying directly below the following oil and gas producing fields: (i) Swanson River Field—1700 feet. (ii) Beaver Creek Field—1650 feet. (iii) Kenai Gas Field—1300 feet. (2) The portion of aquifers beneath Cook Inlet...

40 CFR 147.102 - Aquifer exemptions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... than the indicated depths below the ground surface, and described by a 1/4 mile area beyond and lying directly below the following oil and gas producing fields: (i) Swanson River Field—1700 feet. (ii) Beaver Creek Field—1650 feet. (iii) Kenai Gas Field—1300 feet. (2) The portion of aquifers beneath Cook Inlet...

40 CFR 147.102 - Aquifer exemptions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... than the indicated depths below the ground surface, and described by a 1/4 mile area beyond and lying directly below the following oil and gas producing fields: (i) Swanson River Field—1700 feet. (ii) Beaver Creek Field—1650 feet. (iii) Kenai Gas Field—1300 feet. (2) The portion of aquifers beneath Cook Inlet...

Vast geologic basins attract Indonesian oil exploration. Pt. 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soeparjadi, R.A.; Slocum, R.C.

1973-10-01

This concluding article of a 3-part series describes key geologic features that make Indonesia's S. and E. Kalimantan, Irian Jaya, and S. China Sea areas prime targets for continuing oil and gas exploration. Thick sedimentary basins in E. Kalimantan contain Indonesia'a largest offshore oilfield and other important developments. New reef discoveries in Irian Jaya highlight an extensive exploration effort. Continued drilling in the huge S. China Sea is assured by near commercial shows in recent wildcats. While many thousands of square miles still do not claim a significant discovery, proven successes such as Kalimantan's Attaka field (Indonesia's largest offshore producer)more » and Irian Jaya's new 23,600 bopd Kasim 3 well provide ample incentive for intensive oil searches. Near commercial recoveries of both gas and oil in Indonesia's huge S. China Sea and the recent testing of a 6,000 bopd oil well in nearby Malaysian waters spur interest in the area's W. Natuna and Miri-Seria sedimentary basins.« less

Perspective for using Nd-Fe-B magnets as a tool for the improvement of the production and transportation of Vietnamese crude oil with high paraffin content

NASA Astrophysics Data System (ADS)

Tung, N. P.; Vinh, N. Q.; Phong, N. T. P.; Long, B. Q. K.; Hung, P. V.

2003-04-01

Controlling the paraffin deposition is one of the most serious and costly problems for high-paraffin crude-oil production and transportation. This holds especially for offshore, deep-water wells and pipelines, like in Vietnam. For finding solutions for these problems, a series of experiments has been performed in order to study the effects of a magnetic field on the rheology of two often produced crude oil samples, using the high and variable magnetic-flux density of a Nd-Fe-B magnet. The resulting changes in the essential characteristics of the magnetically treated (MT) crude oils, like form and size of the paraffin clusters as well as the rheology parameters, have definitely proved the possibility to use a Nd-Fe-B magnetic tool as an environmentally friendly and effective method to control the paraffin deposition in crude oils of Vietnam that have a high paraffin content.

7 CFR 985.152 - Handling report.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) date of acquisition; (e) date when oil was produced; (f) net weight of oil in the lot; (g) quantity of that class of oil in the producer's annual allotment available for handler before this acquisition; and... Allotment Certificate, showing that the acquired oil was within the unused portion of the producer's annual...

7 CFR 985.152 - Handling report.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) date of acquisition; (e) date when oil was produced; (f) net weight of oil in the lot; (g) quantity of that class of oil in the producer's annual allotment available for handler before this acquisition; and... Allotment Certificate, showing that the acquired oil was within the unused portion of the producer's annual...

7 CFR 985.152 - Handling report.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) date of acquisition; (e) date when oil was produced; (f) net weight of oil in the lot; (g) quantity of that class of oil in the producer's annual allotment available for handler before this acquisition; and... Allotment Certificate, showing that the acquired oil was within the unused portion of the producer's annual...

7 CFR 985.152 - Handling report.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) date of acquisition; (e) date when oil was produced; (f) net weight of oil in the lot; (g) quantity of that class of oil in the producer's annual allotment available for handler before this acquisition; and... Allotment Certificate, showing that the acquired oil was within the unused portion of the producer's annual...

Steam flooding from mine workings, a viable alternative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayler, M.F.; Brechtel, C.

1987-05-01

The advent of steam flooding has given new life to several fields in California, substantially increasing the recoverable reserve. This process can be combined with a newly developed concept combining petroleum and mining technology. By placing mine workings 100 ft, more or less, below the bottom of the reservoir, it is possible to safely drill wells upward through the reservoir and complete them in such a way that all produced cuttings and fluids are contained within closed pipelines. Each completed well could serve as a steam injection well with continuous gravity-produced oil from the same well. As all fluids wouldmore » flow by gravity to a collection pipeline, the only needed pumps would be at the discharge within the mine shaft. Mine shafts serving the oil field could be placed in environmentally optimum sites roughly one mile apart, eliminating many of the visually objectionable disturbances. Production wells could be placed on one acre or even closer spacing, whatever good engineering dictates. Automatic controls can continuously monitor and control production from each well. Assuming one-acre well spacing, continuous steam flooding, and production from each well, a detailed analysis of anticipated mining costs indicate oil production costs under $5/bbl are possible. Even at $10/BO, a positive cash flow within two years after the start of shaft sinking is expected.« less

Effect of Emulsification Method and Particle Size on the Rate of in vivo Oral Bioavailability of Kenaf (Hibiscus cannabinus L.) Seed Oil.

PubMed

Cheong, Ai Mun; Tan, Chin Ping; Nyam, Kar Lin

2018-05-26

Kenaf (Hibiscus cannabinus L.) seed oil-in-water nanoemulsions stabilized by complexation of beta-cyclodextrin with sodium caseinate and Tween 20 have been shown to have higher bioaccessibility of vitamin E and total phenolic content than nonemulsified kenaf seed oil in the previous in vitro gastrointestinal digestion study. However, its oral bioavailability was unknown. Therefore, the aim of this study was to evaluate the rate of in vivo oral bioavailability of kenaf seed oil-in-water nanoemulsions in comparison with nonemulsified kenaf seed oil and kenaf seed oil macroemulsions during the 180 min of gastrointestinal digestion. Kenaf seed oil macroemulsions were produced by using conventional method. Kenaf seed oil-in-water nanoemulsions had shown improvement in the rate of absorption. At 180 min of digestion time, the total α-tocopherol bioavailability of kenaf seed oil nanoemulsions was increased by 1.7- and 1.4-fold, compared to kenaf seed oil and macroemulsion, respectively. Kenaf seed oil-in-water nanoemulsions were stable in considerably wide range of pH (>5 and <3), suggesting that it can be fortified into beverages within this pH range PRACTICAL APPLICATION: The production of kenaf seed oil-in-water nanoemulsions had provided a delivery system to encapsulate the kenaf seed oil, as well as enhanced the bioaccessibility and bioavailability of kenaf seed oil. Therefore, kenaf seed oil-in-water nanoemulsions exhibit a great potential application in nutraceutical fields. © 2018 Institute of Food Technologists®.

Oil spill dispersants induce formation of marine snow by phytoplankton-associated bacteria.

PubMed

van Eenennaam, Justine S; Wei, Yuzhu; Grolle, Katja C F; Foekema, Edwin M; Murk, AlberTinka J

2016-03-15

Unusually large amounts of marine snow, including Extracellular Polymeric Substances (EPS), were formed during the 2010 Deepwater Horizon oil spill. The marine snow settled with oil and clay minerals as an oily sludge layer on the deep sea floor. This study tested the hypothesis that the unprecedented amount of chemical dispersants applied during high phytoplankton densities in the Gulf of Mexico induced high EPS formation. Two marine phytoplankton species (Dunaliella tertiolecta and Phaeodactylum tricornutum) produced EPS within days when exposed to the dispersant Corexit 9500. Phytoplankton-associated bacteria were shown to be responsible for the formation. The EPS consisted of proteins and to lesser extent polysaccharides. This study reveals an unexpected consequence of the presence of phytoplankton. This emphasizes the need to test the action of dispersants under realistic field conditions, which may seriously alter the fate of oil in the environment via increased marine snow formation. Copyright © 2016 Elsevier Ltd. All rights reserved.

The USSR sets another record

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fueg, J.C.

1988-08-01

The author discusses the oil market in Eastern Europe. Some of the highlights are: '87 Soviet production of 12.478 million bpd was a new world high; Gas output was up 5.79% last year to 70.4 Bcfd, reserves reached 1,488 Tcf; Drilling activity was down in almost all of the satellite states last year; Romania's first offshore Black Sea field is producing 4,300 bpd; and Yugoslavia plans to bring its offshore Adriatic Ivana gas field onstream in 1991.

Delineation of brine contamination in and near the East Poplar oil field, Fort Peck Indian Reservation, northeastern Montana, 2004-09

USGS Publications Warehouse

Thamke, Joanna N.; Smith, Bruce D.

2014-01-01

The extent of brine contamination in the shallow aquifers in and near the East Poplar oil field is as much as 17.9 square miles and appears to be present throughout the entire saturated zone in contaminated areas. The brine contamination affects 15–37 billion gallons of groundwater. Brine contamination in the shallow aquifers east of the Poplar River generally moves to the southwest toward the river and then southward in the Poplar River valley. The likely source of brine contamination in the shallow aquifers is brine that is produced with crude oil in the East Poplar oil field study area. Brine contamination has not only affected the water quality from privately owned wells in and near the East Poplar oil field, but also the city of Poplar’s public water-supply wells. Three water-quality types characterize water in the shallow aquifers; a fourth water-quality type in the study area characterizes the brine. Type 1 is uncontaminated water that is suitable for most domestic purposes and typically contains sodium bicarbonate and sodium/magnesium sulfate as the dominant ions. Type 2 is moderately contaminated water that is suitable for some domestic purposes, but not used for drinking water, and typically contains sodium and chloride as the dominant ions. Type 3 is considerably contaminated water that is unsuitable for any domestic purpose and always contains sodium and chloride as the dominant ions. Type 3 quality of water in the shallow aquifers is similar to Type 4, which is the brine that is produced with crude oil. Electromagnetic apparent conductivity data were collected in the 106 square-mile area and used to determine extent of brine contamination. These data were collected and interpreted in conjunction with water-quality data collected through 2009 to delineate brine plumes in the shallow aquifers. Monitoring wells subsequently were drilled in some areas without existing water wells to confirm most of the delineated brine plumes; however, several possible plumes do not contain either existing water wells or monitoring wells. Analysis of groundwater samples from wells confirms the presence of 12.1 square miles of contamination, as much as 1.7 square miles of which is considerably contaminated (Type 3). Electromagnetic apparent conductivity data in areas with no wells delineate an additional 5.8 square miles of possible contamination, 2.1 square miles of which might be considerably contaminated (Type 3). Storage-tank facilities, oil wells, brine-injection wells, pipelines, and pits are likely sources of brine in the study area. It is not possible to identify discrete oil-related features as likely sources of brine plumes because several features commonly are co-located. During the latter half of the twentieth century, many brine plumes migrated beyond the immediate source area and likely mix together in modern and ancestral Poplar River valley subareas.

Source mechanism inversion and ground motion modeling of induced earthquakes in Kuwait - A Bayesian approach

NASA Astrophysics Data System (ADS)

Gu, C.; Toksoz, M. N.; Marzouk, Y.; Al-Enezi, A.; Al-Jeri, F.; Buyukozturk, O.

2016-12-01

The increasing seismic activity in the regions of oil/gas fields due to fluid injection/extraction and hydraulic fracturing has drawn new attention in both academia and industry. Source mechanism and triggering stress of these induced earthquakes are of great importance for understanding the physics of the seismic processes in reservoirs, and predicting ground motion in the vicinity of oil/gas fields. The induced seismicity data in our study are from Kuwait National Seismic Network (KNSN). Historically, Kuwait has low local seismicity; however, in recent years the KNSN has monitored more and more local earthquakes. Since 1997, the KNSN has recorded more than 1000 earthquakes (Mw < 5). In 2015, two local earthquakes - Mw4.5 in 03/21/2015 and Mw4.1 in 08/18/2015 - have been recorded by both the Incorporated Research Institutions for Seismology (IRIS) and KNSN, and widely felt by people in Kuwait. These earthquakes happen repeatedly in the same locations close to the oil/gas fields in Kuwait (see the uploaded image). The earthquakes are generally small (Mw < 5) and are shallow with focal depths of about 2 to 4 km. Such events are very common in oil/gas reservoirs all over the world, including North America, Europe, and the Middle East. We determined the location and source mechanism of these local earthquakes, with the uncertainties, using a Bayesian inversion method. The triggering stress of these earthquakes was calculated based on the source mechanisms results. In addition, we modeled the ground motion in Kuwait due to these local earthquakes. Our results show that most likely these local earthquakes occurred on pre-existing faults and were triggered by oil field activities. These events are generally smaller than Mw 5; however, these events, occurring in the reservoirs, are very shallow with focal depths less than about 4 km. As a result, in Kuwait, where oil fields are close to populated areas, these induced earthquakes could produce ground accelerations high enough to cause damage to local structures without using seismic design criteria.

The Methods for Connectivity Judgment on Reservoir Layers

NASA Astrophysics Data System (ADS)

Liang, Xiuguang; Dong, Qiang; Liu, Yunyang

2017-12-01

Determining reservoir layer connectivity is the base for an oil field development. The work should be done in the first time. It affects the effects of the following works. However, for some oil field with complex reservoir layers, the study hasn’t fully been done, that causes the oil production rate decreases rapidly and bad oil field development. On the other hand, the simpler the oil field is, the earlier the development should be, thus increasing oil production becomes more and more difficult today, lots of detail works should be done for a complex oil field, the study of reservoir layer connectivity is very important in it.

EOR by stimulated microflora

DOE Office of Scientific and Technical Information (OSTI.GOV)

Svarovskaya, L.I.; Altunina, L.K.; Rozhenkova, Z.A.

1995-12-31

A combined microbiological and physico-chemical method for EOR has been developed for flooded West Siberia oil fields with formation temperature of 45{degrees}-95{degrees}C (318-365K). Formation water includes rich and various biocenoses numbering up to 2 x 10{sup 7} cells per ml. Representatives of genera, i.e, Pseudomonas, Bacillus, Actinomyces, Micrococcus, Mycobacterium, Sarcina, etc. were found to be the most widely distributed microorganisms. The method is based on injection of systems exhibiting high oil displacing capacity and at the same time being an additional nitrous nutrient for endemic populations of microorganisms. Their injection into formation water favors biomass growth by 4-6 orders andmore » promotes syntheses of biosurfactants, biopolymers, acids, etc., and gaseous products. The features of residual oil displacement have been studied on laboratory models using a combined microbiological and physico-chemical method. A curve for the yield of residual oil is presented by two peaks. The first peak is stipulated by the washing action of oil displacement system, and the second one by the effect of metabolites produced at stimulation of biogenic processes. Oil displacement index increases by 15%-30%.« less

Multisensor surveillance data augmentation and prediction with optical multipath signal processing

NASA Astrophysics Data System (ADS)

Bush, G. T., III

1980-12-01

The spatial characteristics of an oil spill on the high seas are examined in the interest of determining whether linear-shift-invariant data processing implemented on an optical computer would be a useful tool in analyzing spill behavior. Simulations were performed on a digital computer using data obtained from a 25,000 gallon spill of soy bean oil in the open ocean. Marked changes occurred in the observed spatial frequencies when the oil spill was encountered. An optical detector may readily be developed to sound an alarm automatically when this happens. The average extent of oil spread between sequential observations was quantified by a simulation of non-holographic optical computation. Because a zero crossover was available in this computation, it may be possible to construct a system to measure automatically the amount of spread. Oil images were subjected to deconvolutional filtering to reveal the force field which acted upon the oil to cause spreading. Some features of spill-size prediction were observed. Calculations based on two sequential photos produced an image which exhibited characteristics of the third photo in that sequence.

Middle Micoene sandstone reservoirs of the Penal/Barrackpore field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyer, B.L.

1991-03-01

The Penal/Barrackpore field was discovered in 1938 and is located in the southern subbasin of onshore Trinidad. The accumulation is one of a series of northeast-southwest trending en echelon middle Miocene anticlinal structures that was later accentuated by late Pliocene transpressional folding. Relative movement of the South American and Caribbean plates climaxed in the middle Miocene compressive tectonic event and produced an imbricate pattern of southward-facing basement-involved thrusts. Further compressive interaction between the plates in the late Pliocene produced a transpressive tectonic episode forming northwest-southeast oriented transcurrent faults, tear faults, basement thrust faults, lystric normal faults, and detached simple foldsmore » with infrequent diapiric cores. The middle Miocene Herrera and Karamat turbiditic sandstones are the primary reservoir rock in the subsurface anticline of the Penal/Barrackpore field. These turbidites were sourced from the north and deposited within the marls and clays of the Cipero Formation. Miocene and Pliocene deltaics and turbidites succeed the Cipero Formation vertically, lapping into preexisting Miocene highs. The late Pliocene transpression also coincides with the onset of oil migration along faults, diapirs, and unconformities from the Cretaceous Naparima Hill source. The Lengua Formation and the upper Forest clays are considered effective seals. Hydrocarbon trapping is structurally and stratigraphically controlled, with structure being the dominant trapping mechanism. Ultimate recoverable reserves for the field are estimated at 127.9 MMBo and 628.8 bcf. The field is presently owned and operated by the Trinidad and Tobago Oil Company Limited (TRINTOC).« less

Thermal maturation and petroleum source rocks in Forest City and Salina basins, mid-continent, U. S. A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newell, K.D.; Watney, W.L.; Hatch, J.R.

1986-05-01

Shales in the Middle Ordovician Simpson Group are probably the source rocks for a geochemically distinct group of lower pristane and low phytane oils produced along the axis of the Forest City basin, a shallow cratonic Paleozoic basin. These oils, termed Ordovician-type oils, occur in some fields in the southern portion of the adjacent Salina basin. Maturation modeling by time-temperature index (TTI) calculations indicate that maturation of both basins was minimal during the early Paleozoic. The rate of maturation significantly increased during the Pennsylvanian because of rapid regional subsidence in response to the downwarping of the nearby Anadarko basin. Whenmore » estimated thicknesses of eroded Pennsylvanian, Permian, and Cretaceous strata are considered, both basins remain relatively shallow, with maximum basement burial probably not exceeding 2 km. According to maturation modeling and regional structure mapping, the axes of both basins should contain Simpson rocks in the early stages of oil generation. The probability of finding commercial accumulations of Ordovician-type oil along the northwest-southeast trending axis of the Salina basin will decrease in a northwestward direction because of (1) westward thinning of the Simpson Group, and (2) lesser maturation due to lower geothermal gradients and shallower paleoburial depths. The optimum localities for finding fields of Ordovician-type oil in the southern Salina basin will be in down-plunge closures on anticlines that have drainage areas near the basin axis.« less

Texas Automated Buoy System 1995-2005 and Beyond

NASA Astrophysics Data System (ADS)

Guinasso, N. L.; Bender, L. C.; Walpert, J. N.; Lee, L. L.; Campbell, L.; Hetland, R. D.; Howard, M. K.; Martin, R. D.

2005-05-01

TABS was established in l995 to provide data to assess oil spill movement along Texas coast for the Texas General Land Office Oil Spill Prevention and Response Program. A system of nine automated buoys provide wind and current data in near real time. Two of these buoys are supported by the Flower Garden Banks Joint Industry Program. A TABS web site provides a public interface to view and download the data. A real time data analysis web page presents a wide variety of useful data products derived from the field measurements. Integration efforts now underway include transfer of buoy data to the National Data Buoy Center for quality control and incorporation into the Global Telecommunications Stream. The TGLO ocean circulation nowcast/forecast modeling system has been in continuous operation since 1998. Two models, POM and ROMS, are used to produce forecasts of near-surface wind driven currents up to 48 hours into the future. Both models are driven using wind fields obtained from the NAM (formerly Eta) forecast models operated by NOAA NCEP. Wind and current fields are displayed on websites in both static and animated forms and are updated four times per day. Under funding from the SURA/SCOOP program we are; 1) revamping the system to conform with the evolving Data Management and Communications (DMAC) framework adopted by the NSF Orion and OCEAN.US IOOS programs, 2) producing model-data comparisons, and 3) integrating the wind and current fields into the GNOME oil trajectory model used by NOAA/Hazmat. Academic research is planned to assimilate near real-time observations from TABS buoys and some 30-40 ADCP instruments scheduled to be mounted on offshore oil platforms in early 2005. Texas Automated Buoy System (TABS) and its associated modeling efforts provide a reliable source of accurate, up-to-date information on currents along the Texas coast. As the nation embarks on the development of an Integrated Ocean Observing System (IOOS), TABS will be an active participant as a foundational regional component to the national backbone of ocean observations.

Detailed north-south cross section showing environments of deposition, organic richness, and thermal maturities of lower Tertiary rocks in the Uinta Basin, Utah

USGS Publications Warehouse

Johnson, Ronald C.

2014-01-01

The Uinta Basin of northeast Utah has produced large amounts of hydrocarbons from lower Tertiary strata since the 1960s. Recent advances in drilling technologies, in particular the development of efficient methods to drill and hydraulically fracture horizontal wells, has spurred renewed interest in producing hydrocarbons from unconventional low-permeability dolomite and shale reservoirs in the lacustrine, Eocene Green River Formation. The Eocene Green River Formation was deposited in Lake Uinta, a long-lived saline lake that occupied the Uinta Basin, the Piceance Basin to the east, and the intervening Douglas Creek arch. The focus of recent drilling activity has been the informal Uteland Butte member of the Green River Formation and to a much lesser extent the overlying R-0 oil shale zone of the Green River Formation. Initial production rates ranging from 500 to 1,500 barrels of oil equivalent per day have been reported from the Uteland Butte member from horizontal well logs that are as long as 4,000 feet (ft);. The cross section presented here extends northward from outcrop on the southern margin of the basin into the basin’s deep trough, located just south of the Uinta Mountains, and transects the area where this unconventional oil play is developing. The Monument Butte field, which is one of the fields located along this line of section, has produced hydrocarbons from conventional sandstone reservoirs in the lower part of the Green River Formation and underlying Wasatch Formation since 1981. A major fluvial-deltaic system entered Lake Uinta from the south, and this new line of section is ideal for studying the effect of the sediments delivered by this drainage on hydrocarbon reservoirs in the Green River Formation. The cross section also transects the Greater Altamont-Bluebell field in the deepest part of the basin, where hydrocarbons have been produced from fractured, highly overpressured marginal lacustrine and fluvial reservoirs in the Green River, Wasatch, and North Horn Formations since 1970. Datum for the cross section is sea level so that hydrocarbon source rocks and reservoir rocks could be integrated into the structural framework of the basin.

Application of petroleum demulsification technology to shale oil emulsions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robertson, R.E.

1983-01-01

Demulsification, the process of emulsion separation, of water-in-oil shale oil emulsions produced by several methods was accomplished using commercial chemical demulsifiers which are used typically for petroleum demulsification. The shale oil emulsions were produced from Green River shale by one in situ and three different above-ground retorts, an in situ high pressure/high temperature steam process, and by washing both retort-produced and hydrotreated shale oils.

Geology and log responses of the Rose Run sandstone in Randolph Township, Portage County, Ohio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moyer, C.C.

1996-09-01

Approximately 75 wells have penetrated the Cambrian Rose Run sandstone in Randolph Township, Portage County, Ohio, about half of which should produce well beyond economic payout. Only one deep test (to the Rose Run or deeper) was drilled in this Township prior to 1990. Two separate and distinct Rose Run producing fields exist in the Township; the western field is predominately gas-productive and the east is predominantly oil-productive. Both fields are on the north side of the Akron-Suffield Fault Zone, which is part of a regional cross-strike structural discontinuity extending from the Pittsburgh, Pennsylvania area northwestward to Lake Erie. Thismore » feature exhibits control over Berea, Oriskany, Newburg, Clinton, and Rose Run production.« less

An Analysis of the Distribution and Economics of Oil Fields for Enhanced Oil Recovery-Carbon Capture and Storage

NASA Astrophysics Data System (ADS)

Hall, Kristyn Ann

The rising carbon dioxide emissions contributing to climate change has lead to the examination of potential ways to mitigate the environmental impact. One such method is through the geological sequestration of carbon (CCS). Although there are several different forms of geological sequestration (i.e. Saline Aquifers, Oil and Gas Reservoirs, Unminable Coal Seams) the current projects are just initiating the large scale-testing phase. The lead entry point into CCS projects is to combine the sequestration with enhanced oil recovery (EOR) due to the improved economic model as a result of the oil recovery and the pre-existing knowledge of the geological structures. The potential scope of CCS-EOR projects throughout the continental United States in terms of a systematic examination of individual reservoir storage potential has not been examined. Instead the majority of the research completed has centered on either estimating the total United States storage potential or the potential of a single specific reservoir. The purpose of this paper is to examine the relationship between oil recovery, carbon dioxide storage and cost during CCS-EOR. The characteristics of the oil and gas reservoirs examined in this study from the Nehring Oil and Gas Database were used in the CCS-EOR model developed by Sean McCoy to estimate the lifting and storage costs of the different reservoirs throughout the continental United States. This allows for an examination of both technical and financial viability of CCS-EOR as an intermediate step for future CCS projects in other geological formations. One option for mitigating climate change is to store industrial CO2 emissions in geologic reservoirs as part of a process known as carbon capture and storage (CCS). There is general consensus that large-scale deployment of CCS would best be initiated by combining geologic sequestration with enhanced oil recovery (EOR), which can use CO2 to improve production from declining oil fields. Revenues from the produced oil could help offset the current high costs of CCS. The cumulative potential of CCS-EOR in the continental U.S. has been evaluated in terms of both CO2 storage capacity and additional oil production. This thesis examines the same potential, but on a reservoir-by-reservoir basis. Reservoir properties from the Nehring Oil and Gas Database are used as inputs to a CCS-EOR model developed by McCoy (YR) to estimate the storage capacity, oil production and CCS-EOR costs for over 10,000 oil reservoirs located throughout the continental United States. We find that 86% of the reservoirs could store ≤1 y or CO2 emissions from a single 500 MW coal-fired power plant (i.e., 3 Mtons CO2). Less than 1% of the reservoirs, on the other hand, appear capable of storing ≥30 y of CO2 emissions from a 500 MW plan. But these larger reservoirs are also estimated to contain 48% of the predicted additional oil that could be produced through CCS-EOR. The McCoy model also predicts that the reservoirs will on average produce 4.5 bbl of oil for each ton of sequestered CO2, a ratio known as the utilization factor. This utilization factor is 1.5 times higher that arrived at by the U.S. Department of Energy, and leads to a cumulative production of oil for all the reservoirs examined of ˜183 billion barrels along with a cumulative storage capacity of 41 Mtons CO2. This is equivalent to 26.5 y of current oil consumption by the nation, and 8.5 y of current coal plant emissions.

The Progreso Basin Province of Northwestern Peru and Southwestern Ecuador: Neogene and Cretaceous-Paleogene Total Petroleum Systems

USGS Publications Warehouse

Higley, Debra K.

2004-01-01

The Progreso Basin province (6083) in northwestern Peru and southwestern Ecuador consists of the Paleogene Santa Elena block and Peru Bank, and the Neogene Tumbes-Progreso subbasin. The Santa Elena block and Peru Bank are part of the Cretaceous-Paleogene Total Petroleum System (TPS)(608302), which contains the Cretaceous-Paleogene Santa Elena Block Assessment Unit (60830201). The Tumbes- Progreso subbasin includes the Neogene TPS (608301) and associated Neogene Pull-Apart Basin Assessment Unit (60830101). The complex tectonic history of the Progreso Basin province influenced depositional and erosional patterns across the region, and also the location, timing, and types of seals, traps, possible source and reservoir rocks, and hydrocarbon generation and migration. Marine shales that are interbedded with and overlie reservoir intervals are the probable hydrocarbon source rocks. Timing of hydrocarbon generation and migration was probably Miocene and younger, following creation of the Tumbes-Progreso subbasin by movement along the Dolores-Guayaquil megashear. More than 220 million barrels of oil (MMBO) and 255 billion cubic feet of gas (BCFG) have been produced from the Progreso Basin province. The means of estimated recoverable oil, gas, and natural gas liquids (NGL) resources from undiscovered fields in the province are 237 MMBO, 695 BCFG, and 32 MMB NGL, respectively. The means of estimated recoverable oil, gas, and NGL resources from undiscovered onshore fields are 45 MMBO, 113 BCFG, and 5 MMBNGL, and from undiscovered offshore fields are 192 BBO, 582 BCFG, and 27 MMBNGL. These are USGS grown undiscovered resources that were determined by using a minimum field size of 1 million barrels of oil equivalent.

Identification of molecular species of polyol oils produced from soybean oil by Pseudomonas aeruginosa e03-12 nrrl b-59991

USDA-ARS?s Scientific Manuscript database

The objective of this study is to develop a bioprocess for the production of polyol oils directly from soybean oil. We reported earlier methods for microbial screening and production of polyol oils from soybean oil (Hou and Lin, 2013). The polyol oil produced by Acinetobacter haemolyticus A01-35 (NR...

Repellent efficacy of DEET, MyggA, neem (Azedirachta indica) oil and chinaberry (Melia azedarach) oil against Anopheles arabiensis, the principal malaria vector in Ethiopia.

PubMed

Abiy, Ephrem; Gebre-Michael, Teshome; Balkew, Meshesha; Medhin, Girmay

2015-05-03

In Ethiopia, Anopheles arabiensis is the main vector responsible for the transmission of malaria in the country and its control mainly involves application of indoor residual spraying (IRS) and use of insecticide-treated bed nets (ITNs). Although the role of repellents for reducing man-vector contact is documented in the literature, the response of An. arabiensis to repellents was not previously evaluated under field conditions in Ethiopia. The trial was conducted in Sodere village assessing the repellent activities of four repellents, of which, two of them were commercially available DEET (N, N-diethyl-1,3-methylbenzamide) and MyggA (p-methane diol) and the other two were laboratory- produced, 20% neem oil and 20% chinaberry oil. A 6 by 6 Latin square design was employed by involving six volunteers who received rotated treatments of repellents and the Ethiopian Niger seed, noog abyssinia (Guizotia abyssinia), and locally called as noog oil (diluents to the two plant oils). Each volunteer also served as control. Volunteers were positioned at a distance of 20-40 m from each other and each was treated with one of the repellents, Niger seed/noog/ oil or untreated. Landing mosquitoes were collected from dusk to down using tests tubes. The tests were done in three replicates. Both DEET and MyggA provided more than 96% protection. The mean protection time for DEET was 8 hrs while the time for MyggA was 6 hrs. Protection obtained from neem oil and chinaberry oil was almost similar (more than 70%), however, the complete protection time for neem was 3 hrs, while that of chinaberry oil was one hour. The commercial products and laboratory-produced repellents can be utilized by individuals to avoid contact with An. arabiensis in Ethiopia.

Study on the interaction mechanism between the special geological environment and their extreme geo-microbes in Dagang Oilfield by combined methods

NASA Astrophysics Data System (ADS)

Yao, Jun

2010-05-01

Geo-microbes and their function were widespread ever since life appeared on the earth. Geo-microbiological process has left a rich and colorful material record in the geological body of earth, the most critical record of which is all sorts of organic hieroglyph and various forms of organic matter derived from bio-organisms, and oil field is the most ideal geological location to preserve these organic matters. It have already produced or might produce petroleum and natural gas sedimentary rocks under natural conditions, also known as olefiant (gas) rock or the parent rock, which is the product of the interaction between the life-system and earth environmental system in the specific geological conditions and integrate the whole microbial ecosystem in the geological time. The microbial community under extreme geological environment of Dagang Oilfield is relatively simple, therefore it is quite easy to investigate the special relationship between geo-microbes and biogeochemistry. We have mastered a large number of information related with the geological condition and biological species of Dagang Oilfield; what's more we also have isolated a number of archimycetes strains with different extremophiles capacity from the core samples collected in the Dagang oil field. At present, we are to proceed with the cooperative research at Environment School of Yale University and Institute of the Earth's biosphere using these strains. In the future, we will work together to carry out geological surveys in the field using international first-class equipment and methods and study the geological environment of Dagang Oilfield utilizing isotope techniques and mineral phase analysis method. Meanwhile we are going to undertake the on-line monitoring of the overall microbial activity of these collected geological samples, the specific metabolic activity of these extreme strains of microorganisms and the biomarkers produced during their metabolic processes under laboratory conditions. According to these research work listed above, we can reveal the mechanism of interaction between the special geological environment of Dagang Oilfield and the extreme geo-microbes, so as to clarify the effects of oil field environment on the extreme geo-microbes and especially the adverse effect of these geo-microbes to the geological environment, which may provide a practical foundation of theoretical basis for the reasons why the Dagang Oilfield can produce oil. Acknowledgement This work was supported in part by grants from National Outstanding Youth Research Foundation of China (40925010), International Joint Key Project from National Natural Science Foundation of China (40920134003), National Natural Science Foundation of China (40873060), and International Joint Key Project from Chinese Ministry of Science and Technology (2009DFA92830), and the 111 Project (08030).

Life Cycle Assessment for the Production of Oil Palm Seeds

PubMed Central

Muhamad, Halimah; Ai, Tan Yew; Khairuddin, Nik Sasha Khatrina; Amiruddin, Mohd Din; May, Choo Yuen

2014-01-01

The oil palm seed production unit that generates germinated oil palm seeds is the first link in the palm oil supply chain, followed by the nursery to produce seedling, the plantation to produce fresh fruit bunches (FFB), the mill to produce crude palm oil (CPO) and palm kernel, the kernel crushers to produce crude palm kernel oil (CPKO), the refinery to produce refined palm oil (RPO) and finally the palm biodiesel plant to produce palm biodiesel. This assessment aims to investigate the life cycle assessment (LCA) of germinated oil palm seeds and the use of LCA to identify the stage/s in the production of germinated oil palm seeds that could contribute to the environmental load. The method for the life cycle impact assessment (LCIA) is modelled using SimaPro version 7, (System for Integrated environMental Assessment of PROducts), an internationally established tool used by LCA practitioners. This software contains European and US databases on a number of materials in addition to a variety of European- and US-developed impact assessment methodologies. LCA was successfully conducted for five seed production units and it was found that the environmental impact for the production of germinated oil palm was not significant. The characterised results of the LCIA for the production of 1000 germinated oil palm seeds showed that fossil fuel was the major impact category followed by respiratory inorganics and climate change. PMID:27073598

Life Cycle Assessment for the Production of Oil Palm Seeds.

PubMed

Muhamad, Halimah; Ai, Tan Yew; Khairuddin, Nik Sasha Khatrina; Amiruddin, Mohd Din; May, Choo Yuen

2014-12-01

The oil palm seed production unit that generates germinated oil palm seeds is the first link in the palm oil supply chain, followed by the nursery to produce seedling, the plantation to produce fresh fruit bunches (FFB), the mill to produce crude palm oil (CPO) and palm kernel, the kernel crushers to produce crude palm kernel oil (CPKO), the refinery to produce refined palm oil (RPO) and finally the palm biodiesel plant to produce palm biodiesel. This assessment aims to investigate the life cycle assessment (LCA) of germinated oil palm seeds and the use of LCA to identify the stage/s in the production of germinated oil palm seeds that could contribute to the environmental load. The method for the life cycle impact assessment (LCIA) is modelled using SimaPro version 7, (System for Integrated environMental Assessment of PROducts), an internationally established tool used by LCA practitioners. This software contains European and US databases on a number of materials in addition to a variety of European- and US-developed impact assessment methodologies. LCA was successfully conducted for five seed production units and it was found that the environmental impact for the production of germinated oil palm was not significant. The characterised results of the LCIA for the production of 1000 germinated oil palm seeds showed that fossil fuel was the major impact category followed by respiratory inorganics and climate change.

Mississippian Barnett Shale, Fort Worth basin, north-central Texas: Gas-shale play with multi-trillion cubic foot potential

USGS Publications Warehouse

Montgomery, S.L.; Jarvie, D.M.; Bowker, K.A.; Pollastro, R.M.

2005-01-01

The Mississippian Barnett Shale serves as source, seal, and reservoir to a world-class unconventional natural-gas accumulation in the Fort Worth basin of north-central Texas. The formation is a lithologically complex interval of low permeability that requires artificial stimulation to produce. At present, production is mainly confined to a limited portion of the northern basin where the Barnett Shale is relatively thick (>300 ft; >92 m), organic rich (present-day total organic carbon > 3.0%), thermally mature (vitrinite reflectance > 1.1%), and enclosed by dense limestone units able to contain induced fractures. The most actively drilled area is Newark East field, currently the largest gas field in Texas. Newark East is 400 mi2 (1036 km2) in extent, with more than 2340 producing wells and about 2.7 tcf of booked gas reserves. Cumulative gas production from Barnett Shale wells through 2003 was about 0.8 tcf. Wells in Newark East field typically produce from depths of 7500 ft (2285 m) at rates ranging from 0.5 to more than 4 mmcf/day. Estimated ultimate recoveries per well range from 0.75 to as high as 7.0 bcf. Efforts to extend the current Barnett play beyond the field limits have encountered several challenges, including westward and northward increases in oil saturation and the absence of lithologic barriers to induced fracture growth. Patterns of oil and gas occurrence in the Barnett, in conjunction with maturation and burial-history data, indicate a complex, multiphased thermal evolution, with episodic expulsion of hydrocarbons and secondary cracking of primary oils to gas in portions of the basin where paleotemperatures were especially elevated. These and other data imply a large-potential Barnett resource for the basin as a whole (possibly > 200 tcf gas in place). Recent assessment by the U.S. Geological Survey suggests a mean volume of 26.2 tcf of undiscovered, technically recoverable gas in the central Fort Worth basin. Recovery of a significant portion of this undiscovered resource will require continued improvements in geoscientific characterization and approaches to stimulation of the Barnett reservoirs. Copyright ?? 2005. The American Association of Petroleum Geologists. All rights reserved.

Geochemical effects of CO2 injection on produced water chemistry at an enhanced oil recovery site in the Permian Basin of northwest Texas, USA: Preliminary geochemical and Li isotope results

NASA Astrophysics Data System (ADS)

Pfister, S.; Gardiner, J.; Phan, T. T.; Macpherson, G. L.; Diehl, J. R.; Lopano, C. L.; Stewart, B. W.; Capo, R. C.

2014-12-01

Injection of supercritical CO2 for enhanced oil recovery (EOR) presents an opportunity to evaluate the effects of CO2 on reservoir properties and formation waters during geologic carbon sequestration. Produced water from oil wells tapping a carbonate-hosted reservoir at an active EOR site in the Permian Basin of Texas both before and after injection were sampled to evaluate geochemical and isotopic changes associated with water-rock-CO2 interaction. Produced waters from the carbonate reservoir rock are Na-Cl brines with TDS levels of 16.5-34 g/L and detectable H2S. These brines are potentially diluted with shallow groundwater from earlier EOR water flooding. Initial lithium isotope data (δ7Li) from pre-injection produced water in the EOR field fall within the range of Gulf of Mexico Coastal sedimentary basin and Appalachian basin values (Macpherson et al., 2014, Geofluids, doi: 10.1111/gfl.12084). Pre-injection produced water 87Sr/86Sr ratios (0.70788-0.70795) are consistent with mid-late Permian seawater/carbonate. CO2 injection took place in October 2013, and four of the wells sampled in May 2014 showed CO2 breakthrough. Preliminary comparison of pre- and post-injection produced waters indicates no significant changes in the major inorganic constituents following breakthrough, other than a possible drop in K concentration. Trace element and isotope data from pre- and post-breakthrough wells are currently being evaluated and will be presented.

Critical Elements in Produced Fluids from Nevada and Utah

DOE Data Explorer

Simmons, Stuart

2017-07-27

Critical elements and related analytical data for produced fluids from geothermal fields in Nevada and Utah, Sevier thermal belt hot springs, Utah, and Uinta basin oil-gas wells, Utah are reported. Analytical results include pH, major species, trace elements, transition metals, other metals, metalloids and REEs. Gas samples were collected and analyzed from Beowawe, Dixie Valley, Roosevelt Hot Springs, and Thermo. Helium gases and helium isotopes were analyzed on samples collected at Patua, San Emido and two wells in the Uinta basin.

Consolidation of geologic studies of geopressured-geothermal resources in Texas: Barrier-bar tidal-channel reservoir facies architecture, Jackson Group, Prado field, South Texas; Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seni, S.J.; Choh, S.J.

1994-01-01

Sandstone reservoirs in the Jackson barrier/strandplain play are characterized by low recovery efficiencies and thus contain a large hydrocarbon resource target potentially amenable to advanced recovery techniques. Prado field, Jim Hogg County, South Texas, has produced over 23 million bbl of oil and over 32 million mcf gas from combination structural-stratigraphic traps in the Eocene lower Jackson Group. Hydrocarbon entrapment at Prado field is a result of anticlinal nosing by differential compaction and updip pinch-out of barrier bar sandstone. Relative base-level lowering resulted in forced regression that established lower Jackson shoreline sandstones in a relatively distal location in central Jimmore » Hogg County. Reservoir sand bodies at Prado field comprise complex assemblages of barrier-bar, tidal-inlet fill, back-barrier bar, and shoreface environments. Subsequent progradation built the barrier-bar system seaward 1 to 2 mi. Within the barrier-bar system, favorable targets for hydrocarbon reexploration are concentrated in tidal-inlet facies because they possess the greatest degree of depositional heterogeneity. The purpose of this report is (1) to describe and analyze the sand-body architecture, depositional facies variations, and structure of Prado field, (2) to determine controls on distribution of hydrocarbons pertinent to reexploration for bypassed hydrocarbons, (3) to describe reservoir models at Prado field, and (4) to develop new data affecting the suitability of Jackson oil fields as possible candidates for thermally enhanced recovery of medium to heavy oil.« less

3-D seismic data for field development: Landslide field case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raeuchle, S.K.; Carr, T.R.; Tucker, R.D.

1990-05-01

The Landslide field is located on the extreme southern flank of the San Joaquin basin, approximately 25 mi south of Bakersfield, California. The field, discovered in 1985, has produced in excess 9 million bbl of oil with an estimated ultimate recovery of more than 13 MMBO. The Miocene Stevens sands, which form the reservoir units at Landslide field, are interpreted as a series of constructional submarine fan deposits. Deposition of the fans was controlled by paleotopography with an abrupt updip pinch-out of the sands to the southwest. The three-dimensional seismic data over the field was used to locate the bottommore » hole of the landslide 22X-30 development well as close to this abrupt updip pinchout as possible in order to maximize oil recovery. A location was selected two traces (330 ft) from the updip pinch-out as mapped on the seismic data. The well was successfully drilled during 1989, encountering 150 ft of net sand with initial production in excess of 1,500 bbl of oil/day. A pressure buildup test indicates the presence of a boundary approximately 200 ft from the well bore. This boundary is interpreted as the updip pinchout of the Stevens sands against the paleohigh. Based on examination of changes in amplitude, the absence or presence of reservoir-quality sand can be mapped across the paleohighs. Application of three-dimensional seismic data, integration with well data, and in particular reconstruction cuts tied closely to existing wells can be used to map the ultimate extent of the field and contribute to efficient development.« less

Integrated exploration method used in search for stratigraphic traps in Illinois basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caserotti, P.M.

1989-08-01

A new oil pool was discovered in Marion County, Illinois, during 1988, using this integrated approach. The discovery is within 2.5 mi of the Salem field, which was discovered in 1938 and has produced more than 387 million bbl of oil. Numerous seismic surveys have been conducted in the area since the Salem field discovery over 50 years ago. Using structure maps developed from the available seismic data, well control, and depositional models, a Ste. Genevieve (middle Mississippian Valmeyeran) prospect was developed on the northeast flank of the Salem anticline. The initial well encountered 8 ft of oil-saturated oolitic limestonemore » in the McClosky zone of the Ste. Genevieve Limestone. Subsequent drilling resulted in four additional oil wells. The size of the reservoir is approximately 120 ac with primary recovery estimated at 200,000 bbl of oil. The depth of the reservoir is 2,250 ft, with an average porosity of 14% and permeability of 300 md. The trapping mechanism is stratigraphic - an oolite bar draped across a gentle nose, which was originally interpreted from the seismic information. Numerous analogous situations exist in the Salem anticline area as well as near other large structures in the basin. An integrated exploration approach can help define these areas and lead to commercial discoveries in mature areas.« less

Well blowout rates and consequences in California Oil and Gas District 4 from 1991 to 2005: Implications for geological storage of carbon dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jordan, Preston; Jordan, Preston D.; Benson, Sally M.

2008-05-15

Well blowout rates in oil fields undergoing thermally enhanced recovery (via steam injection) in California Oil and Gas District 4 from 1991 to 2005 were on the order of 1 per 1,000 well construction operations, 1 per 10,000 active wells per year, and 1 per 100,000 shut-in/idle and plugged/abandoned wells per year. This allows some initial inferences about leakage of CO2 via wells, which is considered perhaps the greatest leakage risk for geological storage of CO2. During the study period, 9% of the oil produced in the United States was from District 4, and 59% of this production was viamore » thermally enhanced recovery. There was only one possible blowout from an unknown or poorly located well, despite over a century of well drilling and production activities in the district. The blowout rate declined dramatically during the study period, most likely as a result of increasing experience, improved technology, and/or changes in safety culture. If so, this decline indicates the blowout rate in CO2-storage fields can be significantly minimized both initially and with increasing experience over time. Comparable studies should be conducted in other areas. These studies would be particularly valuable in regions with CO2-enhanced oil recovery (EOR) and natural gas storage.« less

The Calvin impact crater and its associated oil production, Cass County, Michigan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milstein, R.L.

1996-01-01

The Calvin impact crater is an isolated, nearly circular subsurface structure of Late Ordovician age in southwestern Michigan. The crater is defined by 110 oil and gas test wells, has a diameter of 6.2 km, and consists of a central dome exhibiting 415 m of structural uplift, an annular depression, and an encircling anticlinal rim. Exploration and development of three Devonian oil fields associated wit this structure provide all available subsurface data. All oil production is from the Middle Devonian Traverse Limestone, with the exception of one well producing from the Middle Devonian Sylvania Sandstone. This study models the grossmore » morphology of the Calvin structure using multiple tools and compares the results to known impact craters. Combined results of reflection seismic, gravity, magnetic, and resistivity data, as well as organized relationships between stratigraphic displacement and structural diameters observed in complex impact craters, suggest the Calvin structure is morphologically similar to recognized complex impact craters in sedimentary targets. In addition, individual quartz grains recovered from the Calvin structure exhibit decorated shock lamellae, Boehm lamellae, rhombohederal cleavage, and radiating concussion fractures. Based on the available data, I conclude the Calvin structure is a buried complex impact crater and that the trapping and reservoir characteristics of the associated Calvin 20, Juno Lake, and Calvin 28 oil fields are resultant of the craters morphology.« less

The Calvin impact crater and its associated oil production, Cass County, Michigan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milstein, R.L.

1996-12-31

The Calvin impact crater is an isolated, nearly circular subsurface structure of Late Ordovician age in southwestern Michigan. The crater is defined by 110 oil and gas test wells, has a diameter of 6.2 km, and consists of a central dome exhibiting 415 m of structural uplift, an annular depression, and an encircling anticlinal rim. Exploration and development of three Devonian oil fields associated wit this structure provide all available subsurface data. All oil production is from the Middle Devonian Traverse Limestone, with the exception of one well producing from the Middle Devonian Sylvania Sandstone. This study models the grossmore » morphology of the Calvin structure using multiple tools and compares the results to known impact craters. Combined results of reflection seismic, gravity, magnetic, and resistivity data, as well as organized relationships between stratigraphic displacement and structural diameters observed in complex impact craters, suggest the Calvin structure is morphologically similar to recognized complex impact craters in sedimentary targets. In addition, individual quartz grains recovered from the Calvin structure exhibit decorated shock lamellae, Boehm lamellae, rhombohederal cleavage, and radiating concussion fractures. Based on the available data, I conclude the Calvin structure is a buried complex impact crater and that the trapping and reservoir characteristics of the associated Calvin 20, Juno Lake, and Calvin 28 oil fields are resultant of the craters morphology.« less

40 CFR 49.146 - Recordkeeping requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Federal Implementation Plan for Oil and Natural Gas Production Facilities, Fort Berthold Indian...) Each owner or operator must maintain the following records: (1) The measured barrels of oil produced at the oil and natural gas production facility each time the oil is unloaded from the produced oil...

Catalytic hydrothermal upgrading of crude bio-oils produced from different thermo-chemical conversion routes of microalgae.

PubMed

Duan, Peigao; Wang, Bing; Xu, Yuping

2015-06-01

This study presents experimental results that compare the use of hydrothermal liquefaction (HTL), alcoholysis (Al), pyrolysis (Py) and hydropyrolysis (HPy) for the production of bio-oil from a microalga (Chlorella pyrenoidosa) and the catalytic hydrothermal upgrading of crude bio-oils produced by these four conversion routes. The yields and compositions of bio-oil, solid residue, and gases were evaluated and compared. HTL resulted in a bio-oil that has a higher energy density and superior fuel properties, such as thermal and storage stabilities, compared with the other three conversion routes. The N in crude bio-oils produced from Py and HPy is more easily removed than that in the bio-oils produced from HTL and Al. The upgraded bio-oils contain reduced amounts of certain O-containing and N-containing compounds and significantly increased saturated hydrocarbon contents. All of the upgraded bio-oils have a larger fraction boiling below 350°C than their corresponding crude bio-oils. Copyright © 2015 Elsevier Ltd. All rights reserved.

Oil industry in Uganda: The socio-economic effects on the people of Kabaale Village, Hoima, and Bunyoro region in Uganda

NASA Astrophysics Data System (ADS)

Kyomugasho, Miriam

This thesis examines the socio-economic effects of oil industry on the people of Kabaale Village, Hoima, and Bunyoro region in Uganda. The thesis analyses the current political economy of Uganda and how Uganda is prepared to utilize the proceeds from the oil industry for the development of the country and its people. In addition, the research examines the effects of industry on the people of Uganda by analyzing how the people of Kabaale in Bunyoro region were affected by the plans to construct oil refinery in their region. This field research was done using qualitative methods and the Historical Materialism theoretical framework guided the study. The major findings include; displacement of people from land especially women, lack of accountability from the leadership, and less citizen participation in the policy formulation and oil industry. Ugandans, East Africans and the wider Pan-African world need to re-organize their socio-economic structure to enable people own means of production; participate and form labor organizations. Additionally, there is a need for oil producing African countries to unite and setup and oil fund for resources and investment instead of relying on foreign multinationals or become rentier states.

The future of oil supply

PubMed Central

Miller, Richard G.; Sorrell, Steven R.

2014-01-01

Abundant supplies of oil form the foundation of modern industrial economies, but the capacity to maintain and grow global supply is attracting increasing concern. Some commentators forecast a peak in the near future and a subsequent terminal decline in global oil production, while others highlight the recent growth in ‘tight oil’ production and the scope for developing unconventional resources. There are disagreements over the size, cost and recoverability of different resources, the technical and economic potential of different technologies, the contribution of different factors to market trends and the economic implications of reduced supply. Few debates are more important, more contentious, more wide-ranging or more confused. This paper summarizes the main concepts, terms, issues and evidence that are necessary to understand the ‘peak oil’ debate. These include: the origin, nature and classification of oil resources; the trends in oil production and discoveries; the typical production profiles of oil fields, basins and producing regions; the mechanisms underlying those profiles; the extent of depletion of conventional oil; the risk of an approaching peak in global production; and the potential of various mitigation options. The aim is to introduce the subject to non-specialist readers and provide a basis for the subsequent papers in this Theme Issue. PMID:24298085

Effect of electrolyte concentration on performance of supercapacitor carbon electrode from fibers of oil palm empty fruit bunches

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farma, R.; Awitdrus,; Taer, E.

Fibers of oil palm empty fruit bunches were used to produce self-adhesive carbon grains (SACG). The SACG green monoliths were carbonized in N{sub 2} environment at 800°C to produce carbon monoliths (CM) and the CM was CO{sub 2} activated at 800°C for 4 hour to produce activated carbon monolith electrodes (ACM). The physical properties of the CMs and ACMs were investigated using X-ray diffraction, field emission scanning electron microscopy and nitrogen adsorption-desorption. ACMs were used as electrode to fabricate symmetry supercapacitor cells and the cells which used H{sub 2}SO{sub 4} electrolyte at 0.5, 1.0 and 1.5 M were investigated usingmore » electrochemical impedance spectroscopy, cyclic voltammetry and galvanostatic charge-discharge standard techniques. In this paper we report the physical properties of the ACM electrodes and the effect of electrolyte concentration on the electrochemical properties the ACM electrodes.« less

Management of Reclaimed Produced Water in the Rocky Mountain States Enhanced with the Expanded U.S. Geological Survey Produced Waters Geochemical Database

NASA Astrophysics Data System (ADS)

Gans, K. D.; Blondes, M. S.; Reidy, M. E.; Conaway, C. H.; Thordsen, J. J.; Rowan, E. L.; Kharaka, Y. K.; Engle, M.

2016-12-01

The Rocky Mountain states; Wyoming, Colorado, Montana, New Mexico and Utah produce annually approximately 470,000 acre-feet (3.66 billion barrels) of produced water - water that coexists with oil and gas and is brought to the surface with the pumping of oil and gas wells. Concerns about severe drought, groundwater depletion, and contamination have prompted petroleum operators and water districts to examine the recycling of produced water. Knowledge of the geochemistry of produced waters is valuable in determining the feasibility of produced water reuse. Water with low salinity can be reclaimed for use inside and outside of the petroleum industry. Since a great proportion of petroleum wells in the Rocky Mountain states, especially coal-bed methane wells, have produced water with relatively low salinity (generally <10,000-40,000 mg/L TDS), reclaiming produced water could be important as a drought mitigation strategy, through the irrigation of farmland, blending of low salinity waters with existing drainage basins, re-use in the petroleum industry for hydraulic fracturing or enhanced oil recovery, and even for municipal uses, such as drinking water. The USGS Produced Waters Geochemical Database, available at http://eerscmap.usgs.gov/pwapp, has 60,000 data points in this region (this includes 35,000 new data points added to the 2002 database) and will facilitate studies on the management of produced water for reclamation in the Rocky Mountain region. Expanding on the USGS 2002 database, which contains geochemical analyses of major ions and total dissolved solids, the new data also include geochemical analyses of minor ions and stable isotopes. We have added an interactive web map application which allows the user to filter data on chosen fields (e.g. TDS < 35,000 mg/L). Using the web map application as well as more in-depth investigation on the full data set can provide critical insight for better management of produced waters in water-constrained regions of the Rocky Mountains.

COUPLING THE ALKALINE-SURFACTANT-POLYMER TECHNOLOGY AND THE GELATION TECHNOLOGY TO MAXIMIZE OIL PRODUCTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malcolm Pitts; Jie Qi; Dan Wilson

2005-04-01

Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or more efficient areal sweep efficiency for those with high permeability contrast ''thief zones''. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more oil than waterflooding from swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or those with thief zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. A priormore » fluid-fluid report discussed interaction of different gel chemical compositions and alkaline-surfactant-polymer solutions. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses. Aluminum-polyacrylamide, flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9. Chromium acetate-polyacrylamide flowing and rigid flowing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid flowing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Chromium acetate-xanthan gum rigid gels are not stable to subsequent alkaline-surfactant-polymer solution injection. Resorcinol-formaldehyde gels were stable to subsequent alkaline-surfactant-polymer solution injection. When evaluated in a dual core configuration, injected fluid flows into the core with the greatest effective permeability to the injected fluid. The same gel stability trends to subsequent alkaline-surfactant-polymer injected solution were observed. Aluminum citrate-polyacrylamide, resorcinol-formaldehyde, and the silicate-polyacrylamide gel systems did not produce significant incremental oil in linear corefloods. Both flowing and rigid flowing chromium acetate-polyacrylamide gels and the xanthan gum-chromium acetate gel system produced incremental oil with the rigid flowing gel producing the greatest amount. Higher oil recovery could have been due to higher differential pressures across cores. None of the gels tested appeared to alter alkaline-surfactant-polymer solution oil recovery. Total waterflood plus chemical flood oil recovery sequence recoveries were all similar.« less

Produced water disposal in the southern San Joaquin Basin: a direct analog for brine leakage in response to carbon storage

NASA Astrophysics Data System (ADS)

Jordan, P. D.; Gillespie, J.

2013-12-01

Injection of CO2 during geologic carbon storage pressurizes reservoir fluid, which can cause its migration. Migration of saline water from the reservoir into underground sources of drinking water (USDW) via pathways such as permeable wells and faults is one concern. As of 2010, 2 billion cubic meters (MMMm3) of oil, 10 MMMm3 of water, and 400 MMMm3 of gas had been produced in the southern San Joaquin Valley. A considerable portion of the gas and a majority of the water were injected into production zones for pressure support, water flooding, or as steam for thermal recovery. However a portion of the produced water was disposed of by injection into zones without economic quantities of hydrocarbons, termed saline aquifers in the geologic carbon storage community. These zones often had the shallowest activity in a field, and so had no overlying pressure sink due to production and all oil and gas-related wells in the field encountered or passed through them. The subset of such zones at CO2 storage depths received disposed water volumes equivalent to tens of megatons (MT) of CO2 injected at overpressures of many MPa. For instance a water volume equivalent to over 20 MT of CO2 was injected at a depth of 900 m and an average wellhead pressure of 6 MPa in the Fruitvale oil field, which had almost a thousand wells. Use of USDW for irrigation and consumption is widespread in the area. An increase in total dissolved solids (TDS) in well water is acutely detectable either by taste or effect on crops. Consequently the produced water disposal injection in the southern San Joaquin Valley provides an analog for assessing the occurrence of water leakage impacts due to reservoir pressurization. Almost 230 articles regarding groundwater contamination published from 2000 to 2013 by The Bakersfield Californian, the main newspaper in the area, were assessed. These were written by 71 authors including 38 staff writers, covered 53 different types of facilities or activities that either contaminated groundwater or for which there was such a concern, and discussed 85 different geographic locations. They described groundwater contamination at hundreds of wells during and previous to the publication period. Contamination due to upward leakage caused by produced water disposal injection was not mentioned. Previous research found The Bakersfield Californian covered more well blowouts with the highest public consequence (evacuation) than did reports from the relevant state agency, but had virtually no coverage of the least consequential blow outs. This suggests the lack of reporting of groundwater impacts from leakage due to produced water disposal injection indicates no significant public impact, such as closure of numerous public supply wells, occurred during the article time period or for some years previous. This research continues with analysis of historic groundwater constituent data available from the California State Water Resources Control Board's Geotracker Groundwater Ambient Monitoring & Assessment database. For instance this database contains TDS and other constituent results for 149 wells within or in the immediate vicinity of the Fruitvale oil field.

77 FR 19663 - Notice of Data Availability Concerning Renewable Fuels Produced from Palm Oil Under the RFS...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-02

... Concerning Renewable Fuels Produced from Palm Oil Under the RFS Program; Extension of Comment Period AGENCY... of Data Availability Concerning Renewable Fuels Produced from Palm Oil under the RFS Program'' (the notice is herein referred to as the ``palm oil NODA''). EPA published a NODA, which included a request...

77 FR 8254 - Notice of Data Availability Concerning Renewable Fuels Produced From Palm Oil Under the RFS...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-14

... Concerning Renewable Fuels Produced From Palm Oil Under the RFS Program; Extension of Comment Period AGENCY... of Data Availability Concerning Renewable Fuels Produced From Palm Oil Under the RFS Program'' (the notice is herein referred to as the ``palm oil NODA''). EPA published a NODA, which included a request...

CFD analysis of onshore oil pipelines in permafrost

NASA Astrophysics Data System (ADS)

Nardecchia, Fabio; Gugliermetti, Luca; Gugliermetti, Franco

2017-07-01

Underground pipelines are built all over the world and the knowledge of their thermal interaction with the soil is crucial for their design. This paper studies the "thermal influenced zone" produced by a buried pipeline and the parameters that can influence its extension by 2D-steady state CFD simulations with the aim to improve the design of new pipelines in permafrost. In order to represent a real case, the study is referred to the Eastern Siberia-Pacific Ocean Oil Pipeline at the three stations of Mo'he, Jiagedaqi and Qiqi'har. Different burial depth sand diameters of the pipe are analyzed; the simulation results show that the effect of the oil pipeline diameter on the thermal field increases with the increase of the distance from the starting station.

An ECT/ERT dual-modality sensor for oil-water two-phase flow measurement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Pitao; Wang, Huaxiang; Sun, Benyuan

2014-04-11

This paper presents a new sensor for ECT/ERT dual-modality system which can simultaneously obtain the permittivity and conductivity of the materials in the pipeline. Quasi-static electromagnetic fields are produced by the inner electrodes array sensor of electrical capacitance tomography (ECT) system. The results of simulation show that the data of permittivity and conductivity can be simultaneously obtained from the same measurement electrode and the fusion of two kinds of data may improve the quality of the reconstructed images. For uniform oil-water mixtures, the performance of designed dual-modality sensor for measuring the various oil fractions has been tested on representative datamore » and the results of experiments show that the designed sensor broadens the measurement range compared to single modality.« less

Nuclear winter from gulf war discounted

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marshall, E.

Would a major conflagration in Kuwait's oil fields trigger a climate catastrophe akin to the 'nuclear winter' that got so much attention in the 1980s This question prompted a variety of opinions. The British Meteorological Office and researchers at Lawrence Livermore National Laboratory concluded that the effect of smoke from major oil fires in Kuwait on global temperatures is likely to be small; however, the obscuration of sunlight might significantly reduce surface temperatures locally. Michael MacCracken, leader of the researchers at Livermore, predicts that the worst plausible oil fires in the Gulf would produce a cloud of pollution about asmore » severe as that found on a bad day at the Los Angeles airport. The results of some mathematical modeling by the Livermore research group are reported.« less

Effects of rainfall on oil droplet size and the dispersion of spilled oil with application to Douglas Channel, British Columbia, Canada.

PubMed

Wu, Yongsheng; Hannah, Charles G; Thupaki, Pramod; Mo, Ruping; Law, Brent

2017-01-15

Raindrops falling on the sea surface produce turbulence. The present study examined the influence of rain-induced turbulence on oil droplet size and dispersion of oil spills in Douglas Channel in British Columbia, Canada using hourly atmospheric data in 2011-2013. We examined three types of oils: a light oil (Cold Lake Diluent - CLD), and two heavy oils (Cold Lake Blend - CLB and Access Western Blend - AWB). We found that the turbulent energy dissipation rate produced by rainfalls is comparable to what is produced by wind-induced wave breaking in our study area. With the use of chemical dispersants, our results indicate that a heavy rainfall (rain rate>20mmh -1 ) can produce the maximum droplet size of 300μm for light oil and 1000μm for heavy oils, and it can disperse the light oil with fraction of 22-45% and the heavy oils of 8-13%, respectively. Heavy rainfalls could be a factor for the fate of oil spills in Douglas Channel, especially for a spill of light oil and the use of chemical dispersants. Crown Copyright © 2016. Published by Elsevier Ltd. All rights reserved.

A seismic reflection velocity study of a Mississippian mud-mound in the Illinois basin

NASA Astrophysics Data System (ADS)

Ranaweera, Chamila Kumari

Two mud-mounds have been reported in the Ullin limestone near, but not in, the Aden oil field in Hamilton County, Illinois. One mud-mound is in the Broughton oil field of Hamilton County 25 miles to the south of Aden. The second mud-mound is in the Johnsonville oil field in Wayne County 20 miles to the north of Aden. Seismic reflection profiles were shot in 2012 adjacent to the Aden oil field to evaluate the oil prospects and to investigate the possibility of detecting Mississippian mud-mounds near the Aden field. A feature on one of the seismic profiles was interpreted to be a mud-mound or carbonate buildup. A well drilled at the location of this interpreted structure provided digital geophysical logs and geological logs used to refine the interpretation of the seismic profiles. Geological data from the new well at Aden, in the form of drill cuttings, have been used to essentially confirm the existence of a mud-mound in the Ullin limestone at a depth of 4300 feet. Geophysical well logs from the new well near Aden were used to create 1-D computer models and synthetic seismograms for comparison to the seismic data. The reflection seismic method is widely used to aid interpreting subsurface geology. Processing seismic data is an important step in the method as a properly processed seismic section can give a better image of the subsurface geology whereas a poorly processed section could mislead the interpretation. Seismic reflections will be more accurately depicted with careful determination of seismic velocities and by carefully choosing the processing steps and parameters. Various data processing steps have been applied and parameters refined to produce improved stacked seismic records. The resulting seismic records from the Aden field area indicate a seismic response similar to what is expected from a carbonate mud-mound. One-dimensional synthetic seismograms were created using the available sonic and density logs from the well drilled near the Aden seismic lines. The 1-D synthetics were used by Cory Cantrell of Royal Drilling and Producing Company to identify various reflections on the seismic records. Seismic data was compared with the modeled synthetic seismograms to identify what appears to be a carbonate mud-mound within the Aden study area. No mud-mounds have been previously found in the Aden oil field. Average and interval velocities obtained from the geophysical logs from the wells drilled in the Aden area was compared with the same type of well velocities from the Broughton known mud-mound area to observe the significance of velocity variation related to the un-known mud-mound in the Aden study area. The results of the velocity study shows a similar trends in the wells from both areas and are higher at the bottom of the wells. Another approach was used to observe the variation of root mean square velocities calculated from the sonic log from the well velocity from the Aden area and the stacking velocities obtained from the seismic data adjacent to the well.

Repellent effect of microencapsulated essential oil in lotion formulation against mosquito bites.

PubMed

Misni, Norashiqin; Nor, Zurainee Mohamed; Ahmad, Rohani

2017-01-01

Many essential oils have been reported as natural sources of insect repellents; however, due to high volatility, they present low repellent effect. Formulation technique by using microencapsulation enables to control the volatility of essential oil and thereby extends the duration of repellency. In this study, the effectiveness of microencapsulated essential oils of Alpinia galanga, Citrus grandis and C. aurantifolia in the lotion formulations were evaluated against mosquito bites. Essential oils and N,N-Diethyl-3-methylbenzamide (DEET) were encapsulated by using interfacial pre- cipitation techniques before incorporation into lotion base to form microencapsulated (ME) formulation. The pure essential oil and DEET were also prepared into lotion base to produce non-encapsulated (NE) formulation. All the prepared formulations were assessed for their repellent activity against Culex quinquefasciatus under laboratory condition. Field evaluations also were conducted in three different study sites in Peninsular Malaysia. In addi- tion, Citriodiol® (Mosiquard®) and citronella-based repellents (KAPS®, MozAway® and BioZ Natural®) were also included for comparison. In laboratory conditions, the ME formulations of the essential oils showed no significant difference with regard to the duration of repellent effect compared to the microencapsulated DEET used at the highest con- centration (20%). It exhibited >98% repellent effect for duration of 4 h (p = 0.06). In the field conditions, these formulations demonstrated comparable repellent effect (100% for a duration of 3 h) to Citriodiol® based repellent (Mosiguard®) (p = 0.07). In both test conditions, the ME formulations of the essential oils presented longer duration of 100% repellent effect (between 1 and 2 h) compared to NE formulations. The findings of the study demonstrate that the application of the microencapsulation technique during the preparation of the formulations significantly increases the duration of the repellent effect of the essential oils, suggesting that the ME formulation of essential oils have potential to be commercialized as an alternative plant-based repellent in the market against the mosquitoes.

Class III Mid-Term Project, "Increasing Heavy Oil Reserves in the Wilmington Oil Field Through Advanced Reservoir Characterization and Thermal Production Technologies"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott Hara

2007-03-31

The overall objective of this project was to increase heavy oil reserves in slope and basin clastic (SBC) reservoirs through the application of advanced reservoir characterization and thermal production technologies. The project involved improving thermal recovery techniques in the Tar Zone of Fault Blocks II-A and V (Tar II-A and Tar V) of the Wilmington Field in Los Angeles County, near Long Beach, California. A primary objective has been to transfer technology that can be applied in other heavy oil formations of the Wilmington Field and other SBC reservoirs, including those under waterflood. The first budget period addressed several producibilitymore » problems in the Tar II-A and Tar V thermal recovery operations that are common in SBC reservoirs. A few of the advanced technologies developed include a three-dimensional (3-D) deterministic geologic model, a 3-D deterministic thermal reservoir simulation model to aid in reservoir management and subsequent post-steamflood development work, and a detailed study on the geochemical interactions between the steam and the formation rocks and fluids. State of the art operational work included drilling and performing a pilot steam injection and production project via four new horizontal wells (2 producers and 2 injectors), implementing a hot water alternating steam (WAS) drive pilot in the existing steamflood area to improve thermal efficiency, installing a 2400-foot insulated, subsurface harbor channel crossing to supply steam to an island location, testing a novel alkaline steam completion technique to control well sanding problems, and starting on an advanced reservoir management system through computer-aided access to production and geologic data to integrate reservoir characterization, engineering, monitoring, and evaluation. The second budget period phase (BP2) continued to implement state-of-the-art operational work to optimize thermal recovery processes, improve well drilling and completion practices, and evaluate the geomechanical characteristics of the producing formations. The objectives were to further improve reservoir characterization of the heterogeneous turbidite sands, test the proficiency of the three-dimensional geologic and thermal reservoir simulation models, identify the high permeability thief zones to reduce water breakthrough and cycling, and analyze the nonuniform distribution of the remaining oil in place. This work resulted in the redevelopment of the Tar II-A and Tar V post-steamflood projects by drilling several new wells and converting idle wells to improve injection sweep efficiency and more effectively drain the remaining oil reserves. Reservoir management work included reducing water cuts, maintaining or increasing oil production, and evaluating and minimizing further thermal-related formation compaction. The BP2 project utilized all the tools and knowledge gained throughout the DOE project to maximize recovery of the oil in place.« less

Mechanisms of sulfate removal from subsurface calcium chloride brines: Heletz-Kokhav oilfields, Israel

NASA Astrophysics Data System (ADS)

Gavrieli, Ittai; Starinsky, Avraham; Spiro, Baruch; Aizenshtat, Zeev; Nielsen, Heimo

1995-09-01

The evolution of the Ca-chloride brines in the Heletz Formation, Lower Cretaceous, in the southern coastal plain of Israel was reconstructed through the study of its sulfate concentration and isotopic composition. Particular emphasis was given to the brine-oil interaction in the oilfields and to the sulfate depletion and lower SO 4/Cl ratio in brines in contact with hydrocarbons (oil brines) relative to "oil-free" from dry wells in the same oilfields. A method is presented for a calculation of the amount of sulfate removed from the original seawater in the various stages of its evolution to Ca-chloride brine. These stages include evaporation, dolomitization, and sulfate reduction in different stages of its evolution, from early diagenetic processes to the contact with crude oil. In the present study, based on the δ34S SO 4 and SO 4/Cl ratio, it was found that in the Heletz brines most of the sulfate (80-94%) was removed from the original seawater prior to their interaction with the hydrocarbons and only a negligible fraction of few percent of the sulfate was removed during the crude oil-water contact. The Ca-chloride brines evolved from Messinian (Upper Miocene) seawater that underwent evaporation during the desiccation of the Mediterranean. Sulfate was removed from Messinian lagoon (s) during gypsum precipitation due to evaporation and dolomitization. Bacterial sulfate reduction further depleted the brine in sulfate and changed its isotopic composition, from its original Miocene seawater composition of δ34S SO 4 ˜ 20%o, 26%o. Overall, some 50% of the original sulfate, as normalized to chloride, was removed from the original lagoon through the above processes, mostly by gypsum precipitation. Eastward migration of the Messinian Ca-Chloride brine into the Heletz Formation was accompanied by dolomitization of the country rock. Final depletion of sulfate from the brines took place, and possibly still occurs, in the presence of crude oil in the oilfields. The two oil-producing fields, Heletz and Kokhav, occupy different areas on a Rayleigh distillation diagram. Sulfate depletion in both fields is accompanied by an increase in δ34S SO 4, which reaches a maximum value of 59%o. The above correlation is explained by bacterial sulfate reduction facilitated by the contact with the crude. Samples collected from the same boreholes at time intervals of several months show two opposing trends: sulfate concentration decrease accompanied by increase in δ34S SO 4, and vice versa. While the first can be explained as in situ bacterial sulfate reduction, the latter attest to subsurface brine migration, as would be expected in oil-producing fields.

Determining CO2 storage potential during miscible CO2 enhanced oil recovery: Noble gas and stable isotope tracers

USGS Publications Warehouse

Shelton, Jenna L.; McIntosh, Jennifer C.; Hunt, Andrew; Beebe, Thomas L; Parker, Andrew D; Warwick, Peter D.; Drake, Ronald; McCray, John E.

2016-01-01

Rising atmospheric carbon dioxide (CO2) concentrations are fueling anthropogenic climate change. Geologic sequestration of anthropogenic CO2 in depleted oil reservoirs is one option for reducing CO2 emissions to the atmosphere while enhancing oil recovery. In order to evaluate the feasibility of using enhanced oil recovery (EOR) sites in the United States for permanent CO2 storage, an active multi-stage miscible CO2flooding project in the Permian Basin (North Ward Estes Field, near Wickett, Texas) was investigated. In addition, two major natural CO2 reservoirs in the southeastern Paradox Basin (McElmo Dome and Doe Canyon) were also investigated as they provide CO2 for EOR operations in the Permian Basin. Produced gas and water were collected from three different CO2 flooding phases (with different start dates) within the North Ward Estes Field to evaluate possible CO2 storage mechanisms and amounts of total CO2retention. McElmo Dome and Doe Canyon were sampled for produced gas to determine the noble gas and stable isotope signature of the original injected EOR gas and to confirm the source of this naturally-occurring CO2. As expected, the natural CO2produced from McElmo Dome and Doe Canyon is a mix of mantle and crustal sources. When comparing CO2 injection and production rates for the CO2 floods in the North Ward Estes Field, it appears that CO2 retention in the reservoir decreased over the course of the three injections, retaining 39%, 49% and 61% of the injected CO2 for the 2008, 2010, and 2013 projects, respectively, characteristic of maturing CO2 miscible flood projects. Noble gas isotopic composition of the injected and produced gas for the flood projects suggest no active fractionation, while δ13CCO2 values suggest no active CO2dissolution into formation water, or mineralization. CO2 volumes capable of dissolving in residual formation fluids were also estimated along with the potential to store pure-phase supercritical CO2. Using a combination of dissolution trapping and residual trapping, both volumes of CO2 currently retained in the 2008 and 2013 projects could be justified, suggesting no major leakage is occurring. These subsurface reservoirs, jointly considered, have the capacity to store up to 9 years of CO2 emissions from an average US powerplant.

Biofilter application for control of BTEX compounds from glycol dehydrator condenser vent gases at oil and natural gas producing facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stewart, W.C.; Kamarthi, R.S.

1997-12-31

Compliance with 1990 Clean Air Act Amendments will require cost-effective control technologies to reduce air emissions for petroleum industries. EPA has also proposed a new MACT Rule for Oil and Natural Gas Producing Facilities which will require control of emissions from glycol dehydrator vents. Control of volatile organic compound (VOC) emissions such as benzene, toluene, ethylbenzene, and xylene (BTEX) is one of the major concerns for the petroleum industries. Traditional VOC control methods may not be economically feasible to meet the requirements of these regulations. Recent studies have shown that biofilters can cost-effectively remove BTEX compounds with greater than 95%more » efficiency. This paper describes results from field testing a biofilter at an Oil and Natural Gas Producing facility. The biofilter treats a low flow gas stream containing high concentrations of VOCs and carbon dioxide from a glycol dehydrator condenser vent. A modular high-rate vapor phase biofilter developed by BioiReaction Industries was used to investigate the feasibility of this low-cost technology. Due to the high VOC loading (BTEX compounds up to 18,000 ppm; total VOCs 50,000 to 90,000 ppm), three modular biofilters were installed in series.« less

Why do we conduct energy research in Alabama?

NASA Astrophysics Data System (ADS)

Hills, D. J.

2017-12-01

The purpose of the Energy Investigations Program (EIP) at the Geological Survey of Alabama is to research all geological topics related to energy that would affect the state. The state of Alabama has a rich history of coal, oil, and natural gas production. These traditional fuels are still a necessary part of power production, even as other energy sources are being developed. EIP helps assess the remaining reserves of these hydrocarbons, both from areas that have had extensive production as well as new regions that have yet to have viable production. Our research helps people decide how (or even if) they want to develop the resource. Even so, the research in EIP is not all about fossil fuels. We also investigate how carbon dioxide produced from burning these traditional fuels might be captured and then either used or stored permanently. The same types of geology that are good for producing oil and gas are also often good for geologic storage of carbon dioxide permanently. Carbon dioxide can also be used to produce more oil and gas from an older, less productive field, as it can be used to push more of the hydrocarbon out of the rock. This type of research can lead to job development and economic stability or growth within the state.

Preparation and physicochemical evaluation of emulsified virgin coconut oil (VCO)-carica papaya extract concoction using Tween80

NASA Astrophysics Data System (ADS)

Omar, Hazreen; Zubairi, Saiful Irwan; Fadhilah, Mohd Faizulhelmi; Omar, Dzolkhifli; Asib, Norhayu

2016-11-01

Carica papaya is a member of the Caricaceae. Its leaves have been used in folk medicine for centuries. Recent studies have shown its beneficial effects as an anti-inflammatory agent (Owoyele et al 2008) and anti-tumour15 as well as antioxidant and wound healing properties7. The study has shown that the effect of carica papaya leaves juice intake also can accelerate the rate of increase in platelet count among the patients infected with dengue fever and dengue haemorrhagic fever18. With all the goodness of carica papaya leaves, a formulation with addition of virgin coconut oil (VCO) is produced to give an enhanced supplement beverage to market nowadays. Virgin coconut oil is well known as anti-oxidant4. The combination of these two substances gives a balance combination in healthy supplement. In recent years the application of emulsion is rapidly increasing in many fields such as cosmetics and paints. Emulsions are dispersions of droplets of one liquid in another, immiscible, liquid in which the droplets are of colloidal or near-colloidal sizes. The combination of water and oil (VCO) with addition of non-ionic surfactant Tween80 was constructed using ternary phase diagram. By considering the Hydrophilic-Lipophilic Balance (HLB) value of each substance will help in producing a stable emulsion.

7 CFR 985.56 - Excess oil.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Excess oil. 985.56 Section 985.56 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.56 Excess oil. Oil of any class in excess of a producer's applicable annual allotment shall be identified as...

7 CFR 985.56 - Excess oil.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Excess oil. 985.56 Section 985.56 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.56 Excess oil. Oil of any class in excess of a producer's applicable annual allotment shall be identified as...

7 CFR 985.56 - Excess oil.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Excess oil. 985.56 Section 985.56 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.56 Excess oil. Oil of any class in excess of a producer's applicable annual allotment shall be identified as...

7 CFR 985.56 - Excess oil.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 8 2014-01-01 2014-01-01 false Excess oil. 985.56 Section 985.56 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.56 Excess oil. Oil of any class in excess of a producer's applicable annual allotment shall be identified as...

7 CFR 985.56 - Excess oil.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Excess oil. 985.56 Section 985.56 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.56 Excess oil. Oil of any class in excess of a producer's applicable annual allotment shall be identified as...

Research on breakdown characteristics of oil-paper insulation in compound field at different temperatures

NASA Astrophysics Data System (ADS)

Li, L.; Chen, M. Y.; Zhu, X. C.; Gao, Z. W.; Zhang, H. D.; Li, G. X.; Zhang, J.; Yu, C. L.; Feng, Y. M.

2018-01-01

The breakdown characteristics of oil-paper insulation in AC, DC and compound field at different temperatures were studied. The breakdown mechanism of oil-paper insulation at different temperatures and in AC and DC electric fields was analyzed. The breakdown characteristic mechanisms of the oil-paper insulation in the compound field at different temperatures were obtained: the dielectric strength of oil-paper compound insulation is changed gradually from dependence on oil dielectric strength to dependence on paperboard dielectric strength at low temperature. The dielectric strength of oil-paper compound insulation is always related to the oil dielectric strength closely at high temperature with decrease of AC content.

Oil and gas field code master list, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This document contains data collected through October 1993 and provides standardized field name spellings and codes for all identified oil and/or gas fields in the United States. Other Federal and State government agencies, as well as industry, use the EIA Oil and Gas Field Code Master List as the standard for field identification. A machine-readable version of the Oil and Gas Field Code Master List is available from the National Technical Information Service.

21 CFR 172.225 - Methyl and ethyl esters of fatty acids produced from edible fats and oils.

Code of Federal Regulations, 2013 CFR

2013-04-01

... from edible fats and oils. 172.225 Section 172.225 Food and Drugs FOOD AND DRUG ADMINISTRATION... Methyl and ethyl esters of fatty acids produced from edible fats and oils. Methyl esters and ethyl esters of fatty acids produced from edible fats and oils may be safely used in food, subject to the...

21 CFR 172.225 - Methyl and ethyl esters of fatty acids produced from edible fats and oils.

Code of Federal Regulations, 2012 CFR

2012-04-01

... from edible fats and oils. 172.225 Section 172.225 Food and Drugs FOOD AND DRUG ADMINISTRATION... Methyl and ethyl esters of fatty acids produced from edible fats and oils. Methyl esters and ethyl esters of fatty acids produced from edible fats and oils may be safely used in food, subject to the...

21 CFR 172.225 - Methyl and ethyl esters of fatty acids produced from edible fats and oils.

Code of Federal Regulations, 2014 CFR

2014-04-01

... from edible fats and oils. 172.225 Section 172.225 Food and Drugs FOOD AND DRUG ADMINISTRATION... acids produced from edible fats and oils. Methyl esters and ethyl esters of fatty acids produced from edible fats and oils may be safely used in food, subject to the following prescribed conditions: (a) The...

Brazil advances subsea technology in Marlim pilot

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-03-29

Petroleum Brasileiro SA has extended several water depth records for subsea technology during a pilot project in giant Marlim oil field in the Campos basin off Brazil. Petrobras finished the 10 well Marlim pilot last December. The field's pilot phase was intended to begin early production and enable Petrobras to gather more reservoir data. Ten satellite wells, including two prepilot wells, were completed during the Marlim pilot phase with guidelineless (GLL) wet christmas trees designed and fabricated by FMC Corp., Houston, and CBV Industrial Mechanic SA, Rio de Janeiro. The subsea wells are producing 52,000 b/d of oil and 21.19more » MMCfd of gas in water depths of 1,847-2,562 ft. Marlim pilot well flow is routed to a permanent semisubmersible floating production system (FPS). Oil moves from the FPS to a monobuoy that offloads to a shuttle tanker. In addition to marking the first successful uses of purpose-built GLL wet trees, FMC said the Marlim pilot project allowed GLL subsea technology to evolve from conceptual status into a proven deepwater completion method. The paper describes the project.« less

Concentration and Velocity Measurements of Both Phases in Liquid-Solid Slurries

NASA Astrophysics Data System (ADS)

Altobelli, Stephen; Hill, Kimberly; Caprihan, Arvind

2007-03-01

Natural and industrial slurry flows abound. They are difficult to calculate and to measure. We demonstrate a simple technique for studying steady slurries. We previously used time-of-flight techniques to study pressure driven slurry flow in pipes. Only the continuous phase velocity and concentration fields were measured. The discrete phase concentration was inferred. In slurries composed of spherical, oil-filled pills and poly-methyl-siloxane oils, we were able to use inversion nulling to measure the concentration and velocity fields of both phases. Pills are available in 1-5mm diameter and silicone oils are available in a wide range of viscosities, so a range of flows can be studied. We demonstrated the technique in horizontal, rotating cylinder flows. We combined two tried and true methods to do these experiments. The first used the difference in T1 to select between phases. The second used gradient waveforms with controlled first moments to produce velocity dependent phase shifts. One novel processing method was developed that allows us to use static continuous phase measurements to reference both the continuous and discrete phase velocity images. ?

Storage stability of cooked sausages containing vegetable oils.

PubMed

Papavergou, E J; Ambrosiadis, J A; Psomas, J

1995-01-01

Comminuted cooked sausages were produced using standard industrial practices, by substituting corn oil, sunflower oil, cotton seed oil, soybean oil and hydrogenated vegetable fat for animal fat. When processed, products were assessed for their stability with respect to autoxidation and change in organoleptic properties during vacuum-packed storage in a domestic refrigerator at 4 degrees C. Data obtained indicated that changes in thiobarbituric acid (TBA) values and organoleptic properties of products produced using corn oil, sunflower oil and hydrogenated vegetable fat were similar to those observed for reference material produced using lard. In the case of samples produced using soybean and cotton seed oil, TBA value changes were more pronounced, but did not exceed acceptable limits. A more rapid deterioration of organoleptic characteristics was also observed for the same samples, which showed flavour problems after 3 months of storage at 4 degrees C. Substitution of plant oils for lard considerably reduced the cholesterol content and increased the ratio of unsaturated to saturated fatty acids of cooked sausages.

Modeling winter ozone episodes near oil and natural gas fields in Wyoming

NASA Astrophysics Data System (ADS)

Wu, Yuling; Rappenglück, Bernhard; Pour-Biazar, Arastoo; Field, Robert A.; Soltis, Jeff

2017-04-01

Wintertime ozone episodes have been reported in the oil and natural gas (O&NG) producing fields in Uintah Basin, Utah and the Upper Green River Basin (UGRB) in Wyoming in recent years. High concentrations of ozone precursors facilitated by favorable meteorological conditions, including low wind and shallow boundary layer (BL), were found in these episodes, although the exact roles of these precursor species in different O&NG fields are to be determined. Meanwhile, snow cover is also found to play an important role in these winter ozone episodes as the cold snow covered surface enhances the inversion, further limits the BL and the high snow albedo greatly boosts photolysis reactions that are closely related to ozone chemistry. In this study, we utilize model simulation to explore the role of chemical compositions, in terms of different VOC groups and NOx, and that of the enhanced photolysis due to snow cover in the UGRB ozone episodes in the late winter of 2011.

Biosurfactant-assisted bioremediation of crude oil by indigenous bacteria isolated from Taean beach sediment.

PubMed

Lee, Dong Wan; Lee, Hanbyul; Kwon, Bong-Oh; Khim, Jong Seong; Yim, Un Hyuk; Kim, Beom Seok; Kim, Jae-Jin

2018-05-25

Crude oil and its derivatives are considered as one group of the most pervasive environmental pollutants in marine environments. Bioremediation using oil-degrading bacteria has emerged as a promising green cleanup alternative in more recent years. The employment of biosurfactant-producing and hydrocarbon-utilizing indigenous bacteria enhances the effectiveness of bioremediation by making hydrocarbons bioavailable for degradation. In this study, the best candidates of biosurfactant-producing indigenous bacteria were selected by screening of biochemical tests. The selected bacteria include Bacillus algicola (003-Phe1), Rhodococcus soli (102-Na5), Isoptericola chiayiensis (103-Na4), and Pseudoalteromonas agarivorans (SDRB-Py1). In general, these isolated species caused low surface tension values (33.9-41.3 mN m -1 ), high oil spreading (1.2-2.4 cm), and hydrocarbon emulsification (up to 65%) warranting active degradation of hydrocarbons. FT-IR and LC-MS analyses indicated that the monorhamnolipid (Rha-C 16:1 ) and dirhamnolipid (Rha-Rha-C 6 -C 6:1 ) were commonly produced by the bacteria as potent biosurfactants. The residual crude oil after the biodegradation test was quantitated using GC-MS analysis. The bacteria utilized crude oil as their sole carbon source while the amount of residual crude oil significantly decreased. In addition the cell-free broth containing biosurfactants produced by bacterial strains significantly desorbed crude oil in oil-polluted marine sediment. The selected bacteria might hold additional capacity in crude oil degradation. Biosurfactant-producing indigenous bacteria therefore degrade crude oil hydrocarbon compounds, produce biosurfactants that can increase the emulsification of crude oil and are thus more conducive to the degradation of crude oil. Copyright © 2018 Elsevier Ltd. All rights reserved.

Soil TPH Concentration Estimation Using Vegetation Indices in an Oil Polluted Area of Eastern China

PubMed Central

Zhu, Linhai; Zhao, Xuechun; Lai, Liming; Wang, Jianjian; Jiang, Lianhe; Ding, Jinzhi; Liu, Nanxi; Yu, Yunjiang; Li, Junsheng; Xiao, Nengwen; Zheng, Yuanrun; Rimmington, Glyn M.

2013-01-01

Assessing oil pollution using traditional field-based methods over large areas is difficult and expensive. Remote sensing technologies with good spatial and temporal coverage might provide an alternative for monitoring oil pollution by recording the spectral signals of plants growing in polluted soils. Total petroleum hydrocarbon concentrations of soils and the hyperspectral canopy reflectance were measured in wetlands dominated by reeds (Phragmites australis) around oil wells that have been producing oil for approximately 10 years in the Yellow River Delta, eastern China to evaluate the potential of vegetation indices and red edge parameters to estimate soil oil pollution. The detrimental effect of oil pollution on reed communities was confirmed by the evidence that the aboveground biomass decreased from 1076.5 g m−2 to 5.3 g m−2 with increasing total petroleum hydrocarbon concentrations ranging from 9.45 mg kg−1 to 652 mg kg−1. The modified chlorophyll absorption ratio index (MCARI) best estimated soil TPH concentration among 20 vegetation indices. The linear model involving MCARI had the highest coefficient of determination (R 2 = 0.73) and accuracy of prediction (RMSE = 104.2 mg kg−1). For other vegetation indices and red edge parameters, the R2 and RMSE values ranged from 0.64 to 0.71 and from 120.2 mg kg−1 to 106.8 mg kg−1 respectively. The traditional broadband normalized difference vegetation index (NDVI), one of the broadband multispectral vegetation indices (BMVIs), produced a prediction (R 2 = 0.70 and RMSE = 110.1 mg kg−1) similar to that of MCARI. These results corroborated the potential of remote sensing for assessing soil oil pollution in large areas. Traditional BMVIs are still of great value in monitoring soil oil pollution when hyperspectral data are unavailable. PMID:23342066

Regional chronostratigraphic and depositional hydrocarbon trends in offshore Louisiana State waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

John, C.J.; Jones, B.J.; Harder, B.J.

1996-09-01

Successful exploration for hydrocarbons in the Northern Gulf of Mexico basin requires a systematic understanding of hydrocarbon producing trends, sand body geometries and the geologic, engineering and reservoir parameters of the producing sands. This study forms part of the Offshore Atlas project in progress at the University of Texas at Austin, Bureau of Economic Geology, Texas, in co-operation with the U.S. Department of Interior, Minerals Management Service, and the Geological Survey of Alabama, and is aimed at achieving this goal. In this study, 26 chronozones were grouped into 12 sub-groups. The chronozones were defined on the basis of the benthicmore » foraminiferal biostratigraphic zones and were correlated across the Gulf using well log and seismic data and were projected from the Federal offshore into the State waters. The chronozones on each well log in the 22 cross sections constructed from West Cameron area eastward to the Chandeleur, Breton Sound and Main Pass areas, were subdivided as applicable into four depositional groups consisting of aggradational, progradational, transgressive and submarine fan facies based primarily on SP log shapes. In the Louisiana State waters there are 86 fields containing 679 reservoirs. This includes 212 oil, 344 gas, 33 condensate and 90 combination type reservoirs. Total combined cumulative production (1975-1995) is 454,335,217 barrels of oil, 114,327,696 barrels of condensate and 5,436,623,888 thousand cubic feet of gas. Total assigned production shows the progradational facies to be most productive yielding 51.69% oil 93.84% condensate, and 77.47% gas. The aggradational facies sands produced 46.96% oil, 1.70% condensate and 17.78%. gas. The submarine fan facies yielded 1.21% oil, 4.45% condensate, and 6.74% gas. Production from the transgressive facies sands was less than 0.2% of the total assigned production of oil, gas and condensate.« less

Theoretical Analysis of the Mechanism of Fracture Network Propagation with Stimulated Reservoir Volume (SRV) Fracturing in Tight Oil Reservoirs.

PubMed

Su, Yuliang; Ren, Long; Meng, Fankun; Xu, Chen; Wang, Wendong

2015-01-01

Stimulated reservoir volume (SRV) fracturing in tight oil reservoirs often induces complex fracture-network growth, which has a fundamentally different formation mechanism from traditional planar bi-winged fracturing. To reveal the mechanism of fracture network propagation, this paper employs a modified displacement discontinuity method (DDM), mechanical mechanism analysis and initiation and propagation criteria for the theoretical model of fracture network propagation and its derivation. A reasonable solution of the theoretical model for a tight oil reservoir is obtained and verified by a numerical discrete method. Through theoretical calculation and computer programming, the variation rules of formation stress fields, hydraulic fracture propagation patterns (FPP) and branch fracture propagation angles and pressures are analyzed. The results show that during the process of fracture propagation, the initial orientation of the principal stress deflects, and the stress fields at the fracture tips change dramatically in the region surrounding the fracture. Whether the ideal fracture network can be produced depends on the geological conditions and on the engineering treatments. This study has both theoretical significance and practical application value by contributing to a better understanding of fracture network propagation mechanisms in unconventional oil/gas reservoirs and to the improvement of the science and design efficiency of reservoir fracturing.

Theoretical Analysis of the Mechanism of Fracture Network Propagation with Stimulated Reservoir Volume (SRV) Fracturing in Tight Oil Reservoirs

PubMed Central

Su, Yuliang; Ren, Long; Meng, Fankun; Xu, Chen; Wang, Wendong

2015-01-01

Stimulated reservoir volume (SRV) fracturing in tight oil reservoirs often induces complex fracture-network growth, which has a fundamentally different formation mechanism from traditional planar bi-winged fracturing. To reveal the mechanism of fracture network propagation, this paper employs a modified displacement discontinuity method (DDM), mechanical mechanism analysis and initiation and propagation criteria for the theoretical model of fracture network propagation and its derivation. A reasonable solution of the theoretical model for a tight oil reservoir is obtained and verified by a numerical discrete method. Through theoretical calculation and computer programming, the variation rules of formation stress fields, hydraulic fracture propagation patterns (FPP) and branch fracture propagation angles and pressures are analyzed. The results show that during the process of fracture propagation, the initial orientation of the principal stress deflects, and the stress fields at the fracture tips change dramatically in the region surrounding the fracture. Whether the ideal fracture network can be produced depends on the geological conditions and on the engineering treatments. This study has both theoretical significance and practical application value by contributing to a better understanding of fracture network propagation mechanisms in unconventional oil/gas reservoirs and to the improvement of the science and design efficiency of reservoir fracturing. PMID:25966285

Gas, Water, and Oil Production from the Wasatch Formation, Greater Natural Buttes Field, Uinta Basin, Utah

USGS Publications Warehouse

Nelson, Philip H.; Hoffman, Eric L.

2009-01-01

Gas, oil, and water production data were compiled from 38 wells with production commencing during the 1980s from the Wasatch Formation in the Greater Natural Buttes field, Uinta Basin, Utah. This study is one of a series of reports examining fluid production from tight gas reservoirs, which are characterized by low permeability, low porosity, and the presence of clay minerals in pore space. The general ranges of production rates after 2 years are 100-1,000 mscf/day for gas, 0.35-3.4 barrel per day for oil, and less than 1 barrel per day for water. The water:gas ratio ranges from 0.1 to10 barrel per million standard cubic feet, indicating that free water is produced along with water dissolved in gas in the reservoir. The oil:gas ratios are typical of a wet gas system. Neither gas nor water rates show dependence upon the number of perforations, although for low gas-flow rates there is some dependence upon the number of sandstone intervals that were perforated. Over a 5-year time span, gas and water may either increase or decrease in a given well, but the changes in production rate do not exhibit any dependence upon well proximity or well location.

Processing of palm oil mill wastes based on zero waste technology

NASA Astrophysics Data System (ADS)

Irvan

2018-02-01

Indonesia is currently the main producer of palm oil in the world with a total production reached 33.5 million tons per year. In the processing of fresh fruit bunches (FFB) besides producing palm oil and kernel oil, palm oil mills also produce liquid and solid wastes. The increase of palm oil production will be followed by an increase in the production of waste generated. It will give rise to major environmental issues especially the discharge of liquid waste to the rivers, the emission of methane from digestion pond and the incineration of empty fruit bunches (EFB). This paper describes a zero waste technology in processing palm oil mill waste after the milling process. The technology involves fermentation of palm oil mill effluent (POME) to biogas by using continuous stirred tank reactor (CSTR) in the presence of thermophilic microbes, producing activated liquid organic fertilizer (ALOF) from discharge of treated waste effluent from biogas digester, composting EFB by spraying ALOF on the EFB in the composter, and producing pellet or biochar from EFB by pyrolysis process. This concept can be considered as a promising technology for palm oil mills with the main objective of eliminating the effluent from their mills.

Wage Inequality and Violent Protests in Oil/Gas Producing Countries

NASA Astrophysics Data System (ADS)

Nuraliyev, Nurlan

This work examines contrasting claims made by academic scholars on the relationship between income inequality and political discontent. Does income inequality directly cause social unrest or is this relationship conditional on the level of democratic development? Using the data from 55 oil/gas producing countries between 2010-2013, the author finds: 1) income disparity between an average income per capita of local population and an average income of foreign labor employed in the oil/gas industry results in higher number of violent protests in more democratic oil/gas producing societies; 2) wage disparity between local and foreign labor in the oil/gas industry is associated with higher number of protests in this industry in more democratic oil/gas producing states.

7 CFR 985.58 - Exempt oil.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Exempt oil. 985.58 Section 985.58 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.58 Exempt oil. Oil held by a producer or handler on the effective date of this subpart shall not be...

7 CFR 985.58 - Exempt oil.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Exempt oil. 985.58 Section 985.58 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.58 Exempt oil. Oil held by a producer or handler on the effective date of this subpart shall not be...

7 CFR 985.58 - Exempt oil.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Exempt oil. 985.58 Section 985.58 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.58 Exempt oil. Oil held by a producer or handler on the effective date of this subpart shall not be...

7 CFR 985.58 - Exempt oil.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Exempt oil. 985.58 Section 985.58 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.58 Exempt oil. Oil held by a producer or handler on the effective date of this subpart shall not be...

7 CFR 985.58 - Exempt oil.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 8 2014-01-01 2014-01-01 false Exempt oil. 985.58 Section 985.58 Agriculture... HANDLING OF SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Volume Limitations § 985.58 Exempt oil. Oil held by a producer or handler on the effective date of this subpart shall not be...

Deceased Slabs Drive Oil

NASA Astrophysics Data System (ADS)

Stein, H. J.; Hannah, J. L.

2017-12-01

The application of Re-Os isotope geochemistry to dating single oils is a nascent field [1,2]. Challenges include dissection of oils into asphaltene-maltene (ASPH-MALT) components in a way that preserves meaningful chronologic and source information. Significantly, oil-water mixing rapidly transfers Os to the oil, while Re exchange is sluggish [3]. The Os initial ratio of the oil is shifted in the direction of Os carried in the aqueous fluid, whereas the Re-Os isotopic age is preserved. We show that this phenomenon is operative in natural systems. Further, we show that deserpentinization of old oceanic slabs [4], may be linked to expulsion of Os-enriched waters into overlying sedimentary sections - a process that may be of fundamental importance for oil generation. This conclusion does not diminish the role of traditional organic-rich shales as source rocks for the hydrocarbon, but shows that external fluids are essential to petroleum generation. Moreover, the external fluids may be an important driver for expulsion and migration of oils. We have taken apart several petroleum systems from source rock, to residual oil, to tar mat development, to in situ live oil, through to produced oil. In many cases, a fluid with low 187Os/188Os - unlike that of normal basinal brines - provides a critical component to the oil-water mixture. Funding - CHRONOS project supported by Norwegian petroleum industry (Eni-Norge, Lundin, Aker BP) Acknowledgement - Christine Fichler [4], who first queried us on old slabs and oil, and stimulated ideas. [1] Georgiev, S.V., Stein, H.J., Hannah, J.L., Galimberti, R., Nali, M., Yang, G., and Zimmerman, A. (2016) Re-Os dating of maltenes and asphaltenes within single samples of crude oil: Geochim. Cosmochim. Acta 179: 53-75. [doi.org/10.1016/j.gca.2016.01.016] [2] DiMarzio, J., Georgiev, S.V., Stein, H.J., and Hannah, J.L. (in press) Residency of rhenium and osmium in a heavy crude oil: Geochim. Cosmochim. Acta. [3] Hurtig, N.C., Georgiev, S.V., Stein, H.J., and Hannah, J.L. (in review) Re-Os in oil - in the company of water. [4] Fichler, C., Odinsen, T., Rueslåtten, H., Olesen, O., Vingstad, J.-E., Wienecke, S. (2011) Crustal inhomogenities in the northern North Sea from potential field modeling: inherited structure and serpentinites: Tectonophysics 510: 172-185. [doi:10.1016/j.tecto.2011.06.026

Public Use Land Requirements, Tennessee Colony Lake.

DTIC Science & Technology

1972-03-30

source of pollution by oil and oil field brines. If these and existing gas fields continue to operate, oil -pumping and storage stations and oil and gas ...the lake and large numbers can be expected to visit this area. The land is in the middle of the Cayuga oil field and there are many oil and gas ...Project Area Geographic boundary and physiographic classification The Trinity River meanders south- southeast through Freestone, Anderson, Navarro and

Functional gene diversity of soil microbial communities from five oil-contaminated fields in China.

PubMed

Liang, Yuting; Van Nostrand, Joy D; Deng, Ye; He, Zhili; Wu, Liyou; Zhang, Xu; Li, Guanghe; Zhou, Jizhong

2011-03-01

To compare microbial functional diversity in different oil-contaminated fields and to know the effects of oil contaminant and environmental factors, soil samples were taken from typical oil-contaminated fields located in five geographic regions of China. GeoChip, a high-throughput functional gene array, was used to evaluate the microbial functional genes involved in contaminant degradation and in other major biogeochemical/metabolic processes. Our results indicated that the overall microbial community structures were distinct in each oil-contaminated field, and samples were clustered by geographic locations. The organic contaminant degradation genes were most abundant in all samples and presented a similar pattern under oil contaminant stress among the five fields. In addition, alkane and aromatic hydrocarbon degradation genes such as monooxygenase and dioxygenase were detected in high abundance in the oil-contaminated fields. Canonical correspondence analysis indicated that the microbial functional patterns were highly correlated to the local environmental variables, such as oil contaminant concentration, nitrogen and phosphorus contents, salt and pH. Finally, a total of 59% of microbial community variation from GeoChip data can be explained by oil contamination, geographic location and soil geochemical parameters. This study provided insights into the in situ microbial functional structures in oil-contaminated fields and discerned the linkages between microbial communities and environmental variables, which is important to the application of bioremediation in oil-contaminated sites.

Functional gene diversity of soil microbial communities from five oil-contaminated fields in China

PubMed Central

Liang, Yuting; Van Nostrand, Joy D; Deng, Ye; He, Zhili; Wu, Liyou; Zhang, Xu; Li, Guanghe; Zhou, Jizhong

2011-01-01

To compare microbial functional diversity in different oil-contaminated fields and to know the effects of oil contaminant and environmental factors, soil samples were taken from typical oil-contaminated fields located in five geographic regions of China. GeoChip, a high-throughput functional gene array, was used to evaluate the microbial functional genes involved in contaminant degradation and in other major biogeochemical/metabolic processes. Our results indicated that the overall microbial community structures were distinct in each oil-contaminated field, and samples were clustered by geographic locations. The organic contaminant degradation genes were most abundant in all samples and presented a similar pattern under oil contaminant stress among the five fields. In addition, alkane and aromatic hydrocarbon degradation genes such as monooxygenase and dioxygenase were detected in high abundance in the oil-contaminated fields. Canonical correspondence analysis indicated that the microbial functional patterns were highly correlated to the local environmental variables, such as oil contaminant concentration, nitrogen and phosphorus contents, salt and pH. Finally, a total of 59% of microbial community variation from GeoChip data can be explained by oil contamination, geographic location and soil geochemical parameters. This study provided insights into the in situ microbial functional structures in oil-contaminated fields and discerned the linkages between microbial communities and environmental variables, which is important to the application of bioremediation in oil-contaminated sites. PMID:20861922

Engineering report on the Grayburg Cooperative and unit area, Eddy County, New Mexico

USGS Publications Warehouse

Barnett, John A.; Soyster, Merwin H.

1945-01-01

This report covers the area committed to the Grayburg Cooperative and Unit Agreement (I-Sec. 370) approved by the Assistant Secretary of the Interior on October 5, 1943, hereafter referred to as the "unit area", embracing 4,769.44 acres of public land in T. 17 S., Rs. 29 and 30 E., Eddy County, New Mexico. The area includes portions of the Anderson, Grayburg-Jackson, and Leonard oil fields as defined for proration purposes by the New Mexico Oil Conservation Commission. The unit area is covered by Federal oil and gas leases owned by the Grayburg Oil Company of New Mexico and the Western Production Company, Inc. The Grayburg Unit Association has been formed and designated to conduct and manage all operations in the unit area. As of December 31, 1943, there were forty-six producing oil wells within the unit area. The report has been prepared for the purpose of assisting the Grayburg Unit Association in determining the proper locations of gas-injection wells and the best methods for future operation of the pressure-maintenance system that is being installed for the purpose of retarding the reservoir pressure decline and increasing the ultimate recovery of oil from the Grayburg Zone defined in the above-mentioned agreement as formations not more than 3300 feet below the surface. Data used in the report were obtained from records on file in the Geological Survey office at Roswell, New Mexico, and from the records of the Western Production Company and the Grayburg Oil Company. All data were carefully checked as to accuracy with engineers and field representatives of both companies.

An innovative fast-track development for Cote d`Ivoire

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kreider, G.J.; Barnes, J.E.; Smitherman, J.E.

1996-12-31

In May, 1994, approval was received for the development of the Panthere Gas Field and Lion Oil Field by UMC Petroleum Corporation as operator. At that time, UMC had drilled one well from a jackup at Panthere in 270 feet of water and had set a guyed caisson. Following the Panthere gas discovery, the Lion oil discovery well was drilled in 235 feet of water and another guyed caisson was set. Paragon Engineering Services had been hired in late 1993 to develop project scenarios and cost estimates and as the project evolved, detailed engineering, procurement and construction management services. Productionmore » equipment for 30,000 BOPD, 16,000 BWPD and 75 MMSCFD was to be installed on a jackup drilling rig converted to a Mobile Offshore Production Unit (MOPU) located at the Lion A caisson. Production from Panthere would flow through an 8-inch line to the MOPU. The production equipment on the MOPU would (1) separate oil, water and gas, (2) treat the oil for sale and the water for discharge, (3) pump the oil into an 8-inch pipeline to the refinery in Abidjan, (4) compress the oil well and gas well gas as needed, and (5) dehydrate it for sale. A CALM buoy with shuttle tanker was included in the original plan for early production and as a backup to the oil pipeline. It was also unknown at project initiation whether a gas sales contract would be successfully negotiated, and thus the project was to proceed on the basis of flaring produced gas with capability to add equipment at a later date for gas sales. This paper describes how the project was organized and how this organization allowed the project to accommodate changes and construction problems as they developed while completing the project on time.« less

Secondary oil recovery from selected Carter sandstone oilfields, Black Warrior Basin, Alabama

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, J.C.

1993-04-15

The objectives of this secondary oil recovery project involving the Carter sandstone in northwest Alabama are: (1) To increase the ultimate economic recovery of oil from the Carter reservoirs, thereby increasing domestic reserves and lessening US dependence on foreign oil; (2) To extensively model, test, and monitor the reservoirs so their management is optimized; and (3) To assimilate and transfer the information and results gathered to other US oil companies to encourage them to attempt similar projects. Start-up water injection began on 0 1/12/93 at the Central Bluff Field, and daily operations began on 01/13/93. These operations include monitoring wellheadmore » pressures at the injector and two producers, and injection water treatment. Water injection was running 200-300 bbl/day at the end of February. Once the unit is pressured-up well testing will be performed. Unitization was approved on 03/01/93.b. For the North Fairview Field correlations and log analyses were used to determine the fluid and rock properties. A summary of these properties is included in Table 1. The results of the log analysis were used to construct the hydrocarbon pore volume map shown on Figure 1. The map was planimetered to determine original oil-in-place (OOIP) values and the hydrocarbon pore volume by tract. The OOIP summed over an tracts by this method is 824.7 Mbbl (Figure 2). Original oil-in-place was also calculated directly: two such independent calculations gave 829.4 Mbbl (Table 1) and 835.6 Mbbl (Table 2). Thus, the three estimates of OOIP are within one percent. The approximately 88% of OOIP remaining provides an attractive target for secondary recovery. Injection start-up is planned for mid-June.« less

Updated methodology for nuclear magnetic resonance characterization of shales

NASA Astrophysics Data System (ADS)

Washburn, Kathryn E.; Birdwell, Justin E.

2013-08-01

Unconventional petroleum resources, particularly in shales, are expected to play an increasingly important role in the world's energy portfolio in the coming years. Nuclear magnetic resonance (NMR), particularly at low-field, provides important information in the evaluation of shale resources. Most of the low-field NMR analyses performed on shale samples rely heavily on standard T1 and T2 measurements. We present a new approach using solid echoes in the measurement of T1 and T1-T2 correlations that addresses some of the challenges encountered when making NMR measurements on shale samples compared to conventional reservoir rocks. Combining these techniques with standard T1 and T2 measurements provides a more complete assessment of the hydrogen-bearing constituents (e.g., bitumen, kerogen, clay-bound water) in shale samples. These methods are applied to immature and pyrolyzed oil shale samples to examine the solid and highly viscous organic phases present during the petroleum generation process. The solid echo measurements produce additional signal in the oil shale samples compared to the standard methodologies, indicating the presence of components undergoing homonuclear dipolar coupling. The results presented here include the first low-field NMR measurements performed on kerogen as well as detailed NMR analysis of highly viscous thermally generated bitumen present in pyrolyzed oil shale.

Updated methodology for nuclear magnetic resonance characterization of shales

USGS Publications Warehouse

Washburn, Kathryn E.; Birdwell, Justin E.

2013-01-01

Unconventional petroleum resources, particularly in shales, are expected to play an increasingly important role in the world’s energy portfolio in the coming years. Nuclear magnetic resonance (NMR), particularly at low-field, provides important information in the evaluation of shale resources. Most of the low-field NMR analyses performed on shale samples rely heavily on standard T1 and T2 measurements. We present a new approach using solid echoes in the measurement of T1 and T1–T2 correlations that addresses some of the challenges encountered when making NMR measurements on shale samples compared to conventional reservoir rocks. Combining these techniques with standard T1 and T2 measurements provides a more complete assessment of the hydrogen-bearing constituents (e.g., bitumen, kerogen, clay-bound water) in shale samples. These methods are applied to immature and pyrolyzed oil shale samples to examine the solid and highly viscous organic phases present during the petroleum generation process. The solid echo measurements produce additional signal in the oil shale samples compared to the standard methodologies, indicating the presence of components undergoing homonuclear dipolar coupling. The results presented here include the first low-field NMR measurements performed on kerogen as well as detailed NMR analysis of highly viscous thermally generated bitumen present in pyrolyzed oil shale.

Marginal oil fields, profitable oil at low reserves: How?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agiza, M.N.; Shaheen, S.E.; Barawi, S.A.

1995-12-31

Fields with recoverable reserves of about five million barrels of oil are considered in Egypt as marginal fields. Economics of Egyptian marginal oil fields depend on non-traditional approaches followed in developing and operating such fields. The actual exploration, development and operating expenses and state fiscal terms were used to evaluate the sensitivity of the economic parameters of such marginal fields. The operator net present value (NPV) and internal rate of return (IRR) beside the government take are presented for different parameters used. The purpose is to make acceptable profits out of the marginal oil fields, for the mutual benefits ofmore » both the country and the investors.« less

Paragenesis and reservoir quality within a shallow combination trap: Central West Virginia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bell, D.A.; Siegrist, H.G. Jr.; Buurman, J.D.

1993-12-01

Sandstone character and reservoir quality of the Lower Mississippian Pocono Big Injun sandstone were examined in Granny Creek-Stockly field, Clay County, West Virginia. Sixty-three samples from 6 wells were analyzed using transmitted light, x-ray diffraction, and scanning electron microscopy techniques. The Pocono Big Injun formation is divided into four [open quotes]sands[close quotes] (Injun 1 through 4) based on composition and hydrocarbon productivity. The Injun 1 sand is a fine-grained, carbonate-cemented litharenite below the oil-producing zone. The oil-productive Injun 2 and 3 sands are well sorted, fine-grained litharenites which contain more authigenic and allogenic clay minerals than adjacent sands. These sandsmore » have produced more than 3.4 million bbl of oil from the Granny Creek part of the field since 1925. The Injun 4 sand is generally a coarse-grained sublitharenite with marginal gas production limited to the uppermost section of the sand. The paragenetic sequence consists of (1) minor quartz overgrowths, (2) illite and chlorite grain coatings, (3) quartz overgrowths, (4) early carbonate, (5) kaolinite, (6) calcite, (7) dolomite, and (8) pyrite. Porosity and permeability were not preserved once paragenesis progressed past the kaolinite stage. Porosity and permeability are variably preserved when steps in the paragenetic sequence are absent within the Pocono Group. Where any porosity is identified within the Pocono sandstones, primary porosity is dominant. However, secondary porosity and microporosity in clay-rich intervals are also important.« less

Microgravity

NASA Image and Video Library

1992-07-15

A steel hemisphere was at the core of the Geophysical Fluid Flow Cell (GFFC) that flew on two Spacelab missions. It was capped by a sapphire dome. Silicone oil between the two played the part of a steller atmosphere. An electrostatic field pulled the oil inward to mimic gravity's effects during the experiments. The GFFC thus produced flow patterns that simulated conditions inside the atmospheres of Jupiter and the Sun and other stars. GFFC flew on Spacelab-3 in 1985 and U.S. Microgravity Laboratory-2 in 1995. The principal investigator was John Hart of the University of Colorado at Boulder. It was managed by NASA's Marshall Space Flight Center. (Credit: NASA/Marshall Space Flight Center)

Microgravity

NASA Image and Video Library

1995-10-20

This drawing depicts one set of flow patterns simulated in the Geophysical Fluid Flow Cell (GFFC) that flew on two Spacelab missions. Silicone oil served as the atmosphere around a rotating steel hemisphere (dotted circle) and an electrostatic field pulled the oil inward to mimic gravity's effects during the experiments. The GFFC thus produced flow patterns that simulated conditions inside the atmospheres of Jupiter and the Sun and other stars. The principal investigator was John Hart of the University of Colorado at Boulder. It was managed by NASA's Marshall Space Flight Center (MSFC). An Acrobat PDF copy of this drawing is available at http://microgravity.nasa.gov/gallery. (Credit: NASA/Marshall Space Flight Center)

Microgravity

NASA Image and Video Library

1995-10-10

This composite image depicts one set of flow patterns simulated in the Geophysical Fluid Flow Cell (GFFC) that flew on two Spacelab missions. Silicone oil served as the atmosphere around a rotating steel hemisphere (dotted circle) and an electrostatic field pulled the oil inward to mimic gravity's effects during the experiments. The GFFC thus produced flow patterns that simulated conditions inside the atmospheres of Jupiter and the Sun and other stars. GFFC flew on Spacelab-3 in 1985 and U.S. Microgravity Laboratory-2 in 1995. The principal investigator was John Hart of the University of Colorado at Boulder. It was managed by NASA's Marshall Space Flight Center. (Credit: NASA/Marshall Space Flight Center)

Microgravity

NASA Image and Video Library

1985-05-04

A 16mm film frame shows convective regions inside silicone oil playing the part of a stellar atmosphere in the Geophysical Fluid Flow Cell (GFFC). An electrostatic field pulled the oil inward to mimic gravity's effects during the experiments. The GFFC thus produced flow patterns that simulated conditions inside the atmospheres of Jupiter and the Sun and other stars. Numbers of the frame indicate temperatures and other conditions. This image is from the Spacelab-3 flight in 1985. GFFC was reflown on U.S. Microgravity Laboratory-2 in 1995. The principal investigator was John Hart of the University of Colorado at Boulder. It was managed by NASA's Marshall Space Flight Center. (Credit: NASA/Marshall Space Flight Center)

Production of xanthan gum from a chemically defined medium introduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weisrock, W.P.; Klein, H.S.

1983-02-22

Heteropolysaccharides produced by the action of Xanthomonas bacteria on carbohydrate media have a potential application as film forming agents, as thickeners in oil field drilling fluids and fracturing liquids and as emulsifying, stabilizing, and sizing agents. Heteropolysaccharides, particularly, xanthan gum, have a significant potential as mobility control agents in micellar polymer flooding. Xanthan gum has excellent viscosifying properties at low concentration, is resistant to shear degradation and exhibits only minimal losses in viscosity as a function of temperature, pH, and ionic strength. For these reasons, xanthan gum is an attractive alternative to synthetic polyacrylamides for enhanced oil recovery operations. 15more » claims.« less

Preparation and Characterization of Soybean Oil-Based Polyurethanes for Digital Doming Applications

PubMed Central

Pantone, Vincenzo; Laurenza, Amelita Grazia; Annese, Cosimo; Fracassi, Francesco; Fini, Paola; Nacci, Angelo; Russo, Antonella; Fusco, Caterina

2017-01-01

Polyurethane-resin doming is currently one of the fastest growing markets in the field of industrial graphics and product identification. Semi-rigid bio-based polyurethanes were prepared deriving from soybean oil as a valuable alternative to fossil materials for digital doming and applied to digital mosaic technology. Bio-resins produced can favorably compete with the analogous fossil polymers, giving high-quality surface coatings (ascertained by SEM analyses). In addition, polyurethane synthesis was accomplished by using a mercury- and tin-free catalyst (the commercially available zinc derivative K22) bringing significant benefits in terms of cost efficiency and eco-sustainability. PMID:28773208

Assessment of undiscovered oil and gas resources in the Ventura Basin Province, California, 2016

USGS Publications Warehouse

Tennyson, Marilyn E.; Schenk, Christopher J.; Pitman, Janet K.; Lillis, Paul G.; Klett, Timothy R.; Brownfield, Michael E.; Finn, Thomas M.; Gaswirth, Stephanie B.; Hawkins, Sarah J.; Marra, Kristen R.; Mercier, Tracey J.; Le, Phuong A.; Leathers-Miller, Heidi M.

2017-10-02

The U.S. Geological Survey (USGS) completed a geology-based assessment of undiscovered, technically recoverable conventional and continuous oil and gas resources in the part of the Ventura Basin Province that lies onshore or within State waters (within 3 miles of the shoreline) of California (fig. 1). Conventional oil and gas resources are those that have migrated upward into structural or stratigraphic traps from deep zones where the oil and gas is generated; water is present below the oil or gas. Continuous accumulations, in contrast, are those in which oil or gas is pervasively present in essentially all wells that penetrate them, that may not be structurally or stratigraphically trapped, and that typically lack oil-water or gas-water contacts. They are commonly produced with well-stimulation technology, such as hydraulic fracturing, referred to as “unconventional.” The same stimulation technology, however, is also used in many conventionally trapped accumulations. We estimated both the likely range of oil and gas volumes remaining to be discovered in accumulations similar to existing conventional oil and gas fields in the Ventura Basin Province (previously assessed by Keller [1995] as 1,060 million barrels of oil [MMBO], 1,900 billion cubic feet of gas [BCFG], and 60 million barrels of natural gas liquids [MMBNGL]), and the potential for oil and gas that might be present in a continuous accumulation at extreme depth in the floor of the basin.

Integration of seismic interpretation and petrophysical studies on Hawaz Formation in J-field NC-186 concession, Northwest Murzuq basin, Libya

NASA Astrophysics Data System (ADS)

Mohamed, A. K.; Selim, E. I.; Kashlaf, A.

2016-12-01

This study has been carried out by the integration of seismic interpretations and the well-logging analysis of ten wells distributed in J-field of concession NC-186, Murzuq basin, Libya. Twenty (3D) seismic lines and ten wells have been analyzed. The results of this study indicated that, the main reservoir in this concession is Hawaz Formation. Hawaz has been split into 8 units with a subdivision of Hawaz H4 into three subunits with the objective of better characterization of the three general fine upward intervals. The lower interval of H4 zone presents the better reservoir properties. The depth of reflector H4 ranges from 4100 ft in the northwestern part of the study area and increases to 4600 ft in the southeastern part of the study area. In this study, the outline of the Hawaz paleohighs which is NC-186 Field ;J; is generally trending in the NW-SE direction. The well logging analysis particularly quick look interpretation indicates that Hawaz Formation in the studied wells is mainly oil-bearing with some water-bearing sand levels at the horizons from H4 to and H6 which are potentially the main reservoirs. The water bearing zones are beyond these horizons starting from the sub-horizon H6c and the oil water contact is probably at depth 4495 ft. The crossplot of porosity-saturation for H5 and H6b indicates firmly that these horizons are indeed at irreducible state and will produce mainly oil as indicated in J4-NC186 well, while the crossplot of H8 shows wide scattering of points which is the main characteristic for water producing horizon. The depth of Hawaz Formation H4 is more than 4160 ft in J4, J12 and J16 wells in the northwestern parts of this field and increases to 4400 in the central part of the concession at well J1.

Chromosomal aberrations in lymphocytes of employees in transformer and generator production exposed to electromagnetic fields and mineral oil.

PubMed

Skyberg, K; Hansteen, I L; Vistnes, A I

2001-04-01

The objective was to study the risk of cytogenetic damage among high voltage laboratory workers exposed to electromagnetic fields and mineral oil. This is a cross sectional study of 24 exposed and 24 matched controls in a Norwegian transformer factory. The exposure group included employees in the high voltage laboratory and in the generator soldering department. Electric and magnetic fields and oil mist and vapor were measured. Blood samples were analyzed for chromosomal aberrations in cultured lymphocytes. In addition to conventional cultures, the lymphocytes were also treated with hydroxyurea and caffeine. This procedure inhibits DNA synthesis and repair in vitro, revealing in vivo genotoxic lesions that are repaired during conventional culturing. In conventional cultures, the exposure group and the controls showed similar values for all cytogenetic parameters. In the DNA synthesis- and repair-inhibited cultures, generator welders showed no differences compared to controls. Among high voltage laboratory testers, compared to the controls, the median number of chromatid breaks was doubled (5 vs. 2.5 per 50 cells; P<0.05) the median number of chromosome breaks was 2 vs. 0.5 (P>0.05) and the median number of aberrant cells was 5 vs. 3.5 (P<0.05). Further analysis of the inhibited culture data from this and a previous study indicated that years of exposure and smoking increase the risk of aberrations. We conclude that there was no increase in cytogenetic damage among exposed workers compared to controls in the conventional lymphocyte assay. In inhibited cultures, however, there were indications that electromagnetic fields in combination with mineral oil exposure may produce chromosomal aberrations. Copyright 2001 Wiley-Liss, Inc.

Application of [sup 87]Sr/[sup 86]Sr, [delta][sup 18]O and [delta][sup 13]C isotopes to diagenesis correlation and connectivity of a fractured chalk reservoir, the Sidi El Kilani field, Tunisia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mearns, E.W.; McBride, J.J.; Bramwell, M.

1996-01-01

Oil is produced primarily from open fracture porosity in Upper Cretaceous chalk in the Sidi El Kilani oil field. Strontium Stratigraphy analyses of primary, unaltered matrix chalk has confirmed a Campanian to Maastrichtian age and has allowed dating of the reservoir with a resolution of [+-]1 Ma. This has facilitated reservoir correlation and has indicated where section is missing in certain wells due to faulting. [sup 87]Sr/[sup 86]Sr, [delta][sup 18]O and [delta][sup 13]C analyses suggest an early generation of fracture fill calcite cement may have formed by redistribution of CaCO[sub 3] from underlying carbonate sequences at temperatures in the regionmore » 35-55[degrees]C. Calcite cemented fractures tend to be healed and are not productive. Strontium Isotope Residual Salt Analyses (SrRSA) conducted on core, provide information on the formation water chemistry and reservoir connectivity at the time of oil filling. These data suggest that the NW-SE trending fault system that bisects the field is sealed across much of the fault plane. The main oil pool lies SW of the fault. A later generation of dolomite and barite cements, associated with productive open fractures, have Sr-O-C composition consistent with precipitation from fluids circulating at the time of hydrocarbon charge at temperatures close to current reservoir conditions of 70-75[degrees]C. Predicting the distribution of dolomite cemented open fractures has thus helped guide the development strategy of the field.« less

Application of {sup 87}Sr/{sup 86}Sr, {delta}{sup 18}O and {delta}{sup 13}C isotopes to diagenesis correlation and connectivity of a fractured chalk reservoir, the Sidi El Kilani field, Tunisia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mearns, E.W.; McBride, J.J.; Bramwell, M.

1996-12-31

Oil is produced primarily from open fracture porosity in Upper Cretaceous chalk in the Sidi El Kilani oil field. Strontium Stratigraphy analyses of primary, unaltered matrix chalk has confirmed a Campanian to Maastrichtian age and has allowed dating of the reservoir with a resolution of {+-}1 Ma. This has facilitated reservoir correlation and has indicated where section is missing in certain wells due to faulting. {sup 87}Sr/{sup 86}Sr, {delta}{sup 18}O and {delta}{sup 13}C analyses suggest an early generation of fracture fill calcite cement may have formed by redistribution of CaCO{sub 3} from underlying carbonate sequences at temperatures in the regionmore » 35-55{degrees}C. Calcite cemented fractures tend to be healed and are not productive. Strontium Isotope Residual Salt Analyses (SrRSA) conducted on core, provide information on the formation water chemistry and reservoir connectivity at the time of oil filling. These data suggest that the NW-SE trending fault system that bisects the field is sealed across much of the fault plane. The main oil pool lies SW of the fault. A later generation of dolomite and barite cements, associated with productive open fractures, have Sr-O-C composition consistent with precipitation from fluids circulating at the time of hydrocarbon charge at temperatures close to current reservoir conditions of 70-75{degrees}C. Predicting the distribution of dolomite cemented open fractures has thus helped guide the development strategy of the field.« less

External corrosion and leakage detection of oil and gas pipeline using FBG fiber optics and a trigger

NASA Astrophysics Data System (ADS)

Ge, Yaomou

Oil and gas pipelines play a critical role in delivering the energy resources from producing fields to power communities around the world. However, there are many threats to pipeline integrity, which may lead to significant incidents, causing safety, environmental and economic problems. Corrosion has been a big threat to oil and gas pipelines for a long time, which has attributed to approximately 18% of the significant incidents in oil and gas pipelines. In addition, external corrosion of pipelines accounts for a significant portion (more than 25%) of pipeline failure. External corrosion detection is the research area of this thesis. In this thesis, a review of existing corrosion detection or monitoring methods is presented, and optical fiber sensors show a great promise in corrosion detection of oil and gas pipelines. Several scenarios of optical fiber corrosion sensors are discussed, and two of them are selected for future research. A new corrosion and leakage detection sensor, consisting of a custom designed trigger and a FBG optical fiber, will be presented. This new device has been experimentally tested and it shows great promise.

GEOGRAPHIC INFORMATION SYSTEM APPROACH FOR PLAY PORTFOLIOS TO IMPROVE OIL PRODUCTION IN THE ILLINOIS BASIN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beverly Seyler; John Grube

2004-12-10

Oil and gas have been commercially produced in Illinois for over 100 years. Existing commercial production is from more than fifty-two named pay horizons in Paleozoic rocks ranging in age from Middle Ordovician to Pennsylvanian. Over 3.2 billion barrels of oil have been produced. Recent calculations indicate that remaining mobile resources in the Illinois Basin may be on the order of several billion barrels. Thus, large quantities of oil, potentially recoverable using current technology, remain in Illinois oil fields despite a century of development. Many opportunities for increased production may have been missed due to complex development histories, multiple stackedmore » pays, and commingled production which makes thorough exploitation of pays and the application of secondary or improved/enhanced recovery strategies difficult. Access to data, and the techniques required to evaluate and manage large amounts of diverse data are major barriers to increased production of critical reserves in the Illinois Basin. These constraints are being alleviated by the development of a database access system using a Geographic Information System (GIS) approach for evaluation and identification of underdeveloped pays. The Illinois State Geological Survey has developed a methodology that is being used by industry to identify underdeveloped areas (UDAs) in and around petroleum reservoirs in Illinois using a GIS approach. This project utilizes a statewide oil and gas Oracle{reg_sign} database to develop a series of Oil and Gas Base Maps with well location symbols that are color-coded by producing horizon. Producing horizons are displayed as layers and can be selected as separate or combined layers that can be turned on and off. Map views can be customized to serve individual needs and page size maps can be printed. A core analysis database with over 168,000 entries has been compiled and assimilated into the ISGS Enterprise Oracle database. Maps of wells with core data have been generated. Data from over 1,700 Illinois waterflood units and waterflood areas have been entered into an Access{reg_sign} database. The waterflood area data has also been assimilated into the ISGS Oracle database for mapping and dissemination on the ArcIMS website. Formation depths for the Beech Creek Limestone, Ste. Genevieve Limestone and New Albany Shale in all of the oil producing region of Illinois have been calculated and entered into a digital database. Digital contoured structure maps have been constructed, edited and added to the ILoil website as map layers. This technology/methodology addresses the long-standing constraints related to information access and data management in Illinois by significantly simplifying the laborious process that industry presently must use to identify underdeveloped pay zones in Illinois.« less

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2013 CFR

2013-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2014 CFR

2014-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...

46 CFR 162.050-27 - Oil content meter: Approval tests.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... Viscosity—low. Pour point—very low. Producing country—Algeria. General description—mixed base. Arabian light crude oil Density—medium. Viscosity—medium. Pour point—low. Producing country—Saudi Arabia. General description—mixed base. Nigerian medium crude oil Density—high. Viscosity—medium. Pour point—low. Producing...