Low-temperature operation of a Buck DC/DC converter

NASA Technical Reports Server (NTRS)

Ray, Biswajit; Gerber, Scott S.; Patterson, Richard L.; Myers, Ira T.

1995-01-01

Low-temperature (77 K) operation of a 42/28 V, 175 W, 50 kHz PWM Buck DC/DC converter designed with commercially available components is reported. Overall, the converter losses decreased at 77 K compared to room temperature operation. A full-load efficiency of 97 percent was recorded at liquid-nitrogen temperature, compared to 95.8 percent at room temperature. Power MOSFET operation improved significantly where as the output rectifier operation deteriorated at low-temperature. The performance of the output filter inductor and capacitor did not change significantly at 77 K compared to room temperature performance. It is possible to achieve high-density and high efficiency power conversion at low-temperatures due to improved electronic, electrical and thermal properties of materials.

Operational Suitability Guide. Volume 2. Templates

DTIC Science & Technology

1990-05-01

Intended mission, and the required technical and operational characteristics. The mission must be adequately defined and key hardware and software ...operational availability. With the use of fault-tolerant computer hardware and software , the system R&M will significantly improve end-to-end...should Include both hardware and software elements, as appropriate. Unique characteristics or unique support concepts should be Identified if they result

National Weather Service Warning Performance Based on the WSR-88D.

NASA Astrophysics Data System (ADS)

Polger, Paul D.; Goldsmith, Barry S.; Przywarty, Richard C.; Bocchieri, Joseph R.

1994-02-01

The National Weather Service (NWS) began operational use of the Weather Surveillance Radar-1988 Doppler (WSR-88D) system in March 1991 at Norman, Oklahoma. WSR-88D data have been available to forecasters at five additional offices: Melbourne, Florida, and sterling, Virginia (since January 1992); St. Louis, Missouri, and Dodge City, Kansas (since March 1992); and Houston, Texas (since April 1992). The performance of the severe local storm and flash flood warning programs at the six offices before and after the availability of the WSR-88D was measured quantitatively. The verification procedures and statistical measures used in the quantitative evaluation were those used operationally by the NWS.The statistics show that the warnings improved dramatically when the WSR-88D was in operation. Specifically, the probability of detection of severe weather events increased and the number of false alarms decreased. There was also a marked improvement in the lead time for all severe local storm and flash flood events. These improvements were evident throughout the effective range of the radar. Stratification of severe local storm data by severe thunderstorms versus tornadoes revealed an improvement in the NWS's ability to differentiate between tornadic and nontornadic storms when the WSR-88D was in operation. Four individual cases are examined to illustrate how forecasters used the WSR-88D to achieve the improved results. These cases focus on the unique features of the WSR-88D that provide an advantage over conventional NWS radars.

77 FR 1514 - Biweekly Notice; Applications and Amendments to Facility Operating Licenses Involving No...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-10

... Technical Specification (TS) 3.4.5, ``RCS Leakage Detection Instrumentation,'' consistent with the NRC... monitoring system are the only operable reactor coolant leakage detection monitoring systems. The modified... Coolant System] Leakage Instrumentation,'' Revision 3. The availability of this TS improvement was...

Applied Operations Research: Augmented Reality in an Industrial Environment

NASA Technical Reports Server (NTRS)

Cole, Stuart K.

2015-01-01

Augmented reality is the application of computer generated data or graphics onto a real world view. Its use provides the operator additional information or a heightened situational awareness. While advancements have been made in automation and diagnostics of high value critical equipment to improve readiness, reliability and maintenance, the need for assisting and support to Operations and Maintenance staff persists. AR can improve the human machine interface where computer capabilities maximize the human experience and analysis capabilities. NASA operates multiple facilities with complex ground based HVCE in support of national aerodynamics and space exploration, and the need exists to improve operational support and close a gap related to capability sustainment where key and experienced staff consistently rotate work assignments and reach their expiration of term of service. The initiation of an AR capability to augment and improve human abilities and training experience in the industrial environment requires planning and establishment of a goal and objectives for the systems and specific applications. This paper explored use of AR in support of Operation staff in real time operation of HVCE and its maintenance. The results identified include identification of specific goal and objectives, challenges related to availability and computer system infrastructure.

Modeling the impact of improved aircraft operations technologies on the environment and airline behavior

NASA Astrophysics Data System (ADS)

Foley, Ryan Patrick

The overall goal of this thesis is to determine if improved operations technologies are economically viable for US airlines, and to determine the level of environmental benefits available from such technologies. Though these operational changes are being implemented primarily with the reduction of delay and improvement of throughput in mind, economic factors will drive the rate of airline adoption. In addition, the increased awareness of environmental impacts makes these effects an important aspect of decision-making. Understanding this relationship may help policymakers make decisions regarding implementation of these advanced technologies at airports, and help airlines determine appropriate levels of support to provide for these new technologies. In order to do so, the author models the behavior of a large, profit-seeking airline in response to the introduction of advanced equipage allowing improved operations procedures. The airline response included changes in deployed fleet, assignment of aircraft to routes, and acquisition of new aircraft. From these responses, changes in total fleet-level CO2 emissions and airline profit were tallied. As awareness of the environmental impact of aircraft emissions has grown, several agencies (ICAO, NASA) have moved to place goals for emissions reduction. NASA, in particular, has set goals for emissions reduction through several areas of aircraft technology. Among these are "Operational Improvements," technologies available in the short-term through avionics and airport system upgrades. The studies in this thesis make use of the Fleet-Level Environmental Evaluation Tool (FLEET), a simulation tool developed by Purdue University in support of a NASA-sponsored research effort. This tool models the behavior of a large, profit-seeking airline through an allocation problem. The problem is contained within a systems dynamics type approach that allows feedback between passenger demand, ticket price, and the airline fleet composition so that the demand and airline operations evolve over time. The studies indicate that, despite an increased cost, improved equipage provides benefits to airline profits as long as equipped airports are available. Improved equipage also reduces fuel burn on a per-flight basis, but depending on the percentage of equipped aircraft in the fleet, the overall airline fuel burn may increase. Improved equipage does increase capacity at busy airports - such as Chicago O'Hare - allowing a greater number of aircraft to operate at the airport on any given day. A sensitivity study indicates that, in the FLEET model, airline profits are most sensitive to changes in the underlying demand for air travel, followed by the price of jet fuel. Equipage related factors, such as the number of equipped airports in the network or the cost of improved equipage, have a comparatively minor influence on airline profit. Of these secondary factors, the assumed decrease in trip or segment distance enabled by improved equipage systems has the greatest impact on profit. Ability to retrofit aircraft and entry-in-service date of equipped aircraft has the greatest impact on the number of equipped aircraft in the fleet.

Operational support and service concepts for observatories

NASA Astrophysics Data System (ADS)

Emde, Peter; Chapus, Pierre

2014-08-01

The operational support and service for observatories aim at the provision, the preservation and the increase of the availability and performance of the entire structural, mechanical, drive and control systems of telescopes and the related infrastructure. The operational support and service levels range from the basic service with inspections, preventive maintenance, remote diagnostics and spare parts supply over the availability service with telephone hotline, online and on-site support, condition monitoring and spare parts logistics to the extended service with operations and site and facility management. For the level of improvements and lifecycle management support they consist of expert assessments and studies, refurbishments and upgrades including the related engineering and project management activities.

78 FR 40496 - Notice of availability of the Final Environmental Impact Statement for the Proposed Hollister...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-05

... silver mining operation. Most of the infrastructure to support a mining operation was authorized and.... The Proposed Action consists of underground mining, constructing a new production shaft, improving.... Public comments resulted in the addition of clarifying text, but did not significantly change the...

Integrated long-range UAV/UGV collaborative target tracking

NASA Astrophysics Data System (ADS)

Moseley, Mark B.; Grocholsky, Benjamin P.; Cheung, Carol; Singh, Sanjiv

2009-05-01

Coordinated operations between unmanned air and ground assets allow leveraging of multi-domain sensing and increase opportunities for improving line of sight communications. While numerous military missions would benefit from coordinated UAV-UGV operations, foundational capabilities that integrate stove-piped tactical systems and share available sensor data are required and not yet available. iRobot, AeroVironment, and Carnegie Mellon University are working together, partially SBIR-funded through ARDEC's small unit network lethality initiative, to develop collaborative capabilities for surveillance, targeting, and improved communications based on PackBot UGV and Raven UAV platforms. We integrate newly available technologies into computational, vision, and communications payloads and develop sensing algorithms to support vision-based target tracking. We first simulated and then applied onto real tactical platforms an implementation of Decentralized Data Fusion, a novel technique for fusing track estimates from PackBot and Raven platforms for a moving target in an open environment. In addition, system integration with AeroVironment's Digital Data Link onto both air and ground platforms has extended our capabilities in communications range to operate the PackBot as well as in increased video and data throughput. The system is brought together through a unified Operator Control Unit (OCU) for the PackBot and Raven that provides simultaneous waypoint navigation and traditional teleoperation. We also present several recent capability accomplishments toward PackBot-Raven coordinated operations, including single OCU display design and operation, early target track results, and Digital Data Link integration efforts, as well as our near-term capability goals.

Use of Satellite Data Assimilation to Infer Land Surface Thermal Inertia

NASA Technical Reports Server (NTRS)

Lapenta, William; McNider, Richard T.; Biazar, Arastoo; Suggs, Ron; Jedlovec, Gary; Dembek, Scott

2002-01-01

There are two important but observationally uncertain parameters in the grid averaged surface energy budgets of mesoscale models - surface moisture availability and thermal heat capacity. A technique has been successfully developed for assimilating Geostationary Operational Environmental Satellite (GOES) skin temperature tendencies during the mid-morning time frame to improve specification of surface moisture. In a new application of the technique, the use of satellite skin temperature tendencies in early evening is explored to improve specification of the surface thermal heat capacity. Together, these two satellite assimilation constraints have been shown to significantly improve the characterization of the surface energy budget of a mesoscale model on fine spatial scales. The GOES assimilation without the adjusted heat capacity was run operationally during the International H2O Project on a 12-km grid. This paper presents the results obtained when using both the moisture availability and heat capacity retrievals in concert. Preliminary results indicate that retrieved moisture availability alone improved the verification statistics of 2-meter temperature and dew point forecasts. Results from the 1.5 month long study period using the bulk heat capacity will be presented at the meeting.

Early tracking would improve the operative experience of general surgery residents.

PubMed

Stain, Steven C; Biester, Thomas W; Hanks, John B; Ashley, Stanley W; Valentine, R James; Bass, Barbara L; Buyske, Jo

2010-09-01

High surgical complexity and individual career goals has led most general surgery (GS) residents to pursue fellowship training, resulting in a shortage of surgeons who practice broad-based general surgery. We hypothesize that early tracking of residents would improve operative experience of residents planning to be general surgeons, and could foster greater interest and confidence in this career path. Surgical Operative Log data from GS and fellowship bound residents (FB) applying for the 2008 American Board of Surgery Qualifying Examination (QE) were used to construct a hypothetical training model with 6 months of early specialization (ESP) for FB residents in 4 specialties (cardiac, vascular, colorectal, pediatric); and presumed these cases would be available to GS residents within the same program. A total of 142 training programs had both FB residents (n = 237) and GS residents (n = 402), and represented 70% of all 2008 QE applicants. The mean numbers of operations by FB and GS residents were 1131 and 1091, respectively. There were a mean of 252 cases by FB residents in the chief year, theoretically making 126 cases available for each GS resident. In 9 defined categories, the hypothetical model would result in an increase in the 5-year operative experience of GS residents (mastectomy 6.5%; colectomy 22.8%; gastrectomy 23.4%; antireflux procedures 23.4%; pancreatic resection 37.4%; liver resection 29.3%; endocrine procedures 19.6%; trauma operations 13.3%; GI endoscopy 6.5%). The ESP model improves operative experience of GS residents, particularly for complex gastrointestinal procedures. The expansion of subspecialty ESP should be considered.

The value of improved wind power forecasting: Grid flexibility quantification, ramp capability analysis, and impacts of electricity market operation timescales

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Qin; Wu, Hongyu; Florita, Anthony R.

The value of improving wind power forecasting accuracy at different electricity market operation timescales was analyzed by simulating the IEEE 118-bus test system as modified to emulate the generation mixes of the Midcontinent, California, and New England independent system operator balancing authority areas. The wind power forecasting improvement methodology and error analysis for the data set were elaborated. Production cost simulation was conducted on the three emulated systems with a total of 480 scenarios, considering the impacts of different generation technologies, wind penetration levels, and wind power forecasting improvement timescales. The static operational flexibility of the three systems was comparedmore » through the diversity of generation mix, the percentage of must-run baseload generators, as well as the available ramp rate and the minimum generation levels. The dynamic operational flexibility was evaluated by the real-time upward and downward ramp capacity. Simulation results show that the generation resource mix plays a crucial role in evaluating the value of improved wind power forecasting at different timescales. In addition, the changes in annual operational electricity generation costs were mostly influenced by the dominant resource in the system. Lastly, the impacts of pumped-storage resources, generation ramp rates, and system minimum generation level requirements on the value of improved wind power forecasting were also analyzed.« less

The value of improved wind power forecasting: Grid flexibility quantification, ramp capability analysis, and impacts of electricity market operation timescales

DOE PAGES

Wang, Qin; Wu, Hongyu; Florita, Anthony R.; ...

2016-11-11

The value of improving wind power forecasting accuracy at different electricity market operation timescales was analyzed by simulating the IEEE 118-bus test system as modified to emulate the generation mixes of the Midcontinent, California, and New England independent system operator balancing authority areas. The wind power forecasting improvement methodology and error analysis for the data set were elaborated. Production cost simulation was conducted on the three emulated systems with a total of 480 scenarios, considering the impacts of different generation technologies, wind penetration levels, and wind power forecasting improvement timescales. The static operational flexibility of the three systems was comparedmore » through the diversity of generation mix, the percentage of must-run baseload generators, as well as the available ramp rate and the minimum generation levels. The dynamic operational flexibility was evaluated by the real-time upward and downward ramp capacity. Simulation results show that the generation resource mix plays a crucial role in evaluating the value of improved wind power forecasting at different timescales. In addition, the changes in annual operational electricity generation costs were mostly influenced by the dominant resource in the system. Lastly, the impacts of pumped-storage resources, generation ramp rates, and system minimum generation level requirements on the value of improved wind power forecasting were also analyzed.« less

76 FR 70130 - Environmental Impacts Statements; Notice of Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-10

... Transmission Line, Plan-of-Operation Permit, Kootenai National Forest, Sanders County, MT, Comment Period Ends..., Coconino National Forest Travel Management Project, Proposes to Designate a System of Road and Motorized..., Proposed On-the-Ground Treatments to Improve Forest Health and Improve or Protect Red Squirrel Habitat...

National Transonic Facility: A review of the operational plan

NASA Technical Reports Server (NTRS)

Liepmann, H. W.; Black, R. E.; Dietz, R. O.; Kirchner, M. E.; Sears, W. R.

1980-01-01

The proposed National Transonic Facility (NTF) operational plan is reviewed. The NTF will provide an aerodynamic test capability significantly exceeding that of other transonic regime wind tunnels now available. A limited number of academic research program that might use the NTF are suggested. It is concluded that the NTF operational plan is useful for management, technical, instrumentation, and model building techniques available in the specialized field of aerodynamic analysis and simulation. It is also suggested that NASA hold an annual conference to discuss wind tunnel research results and to report on developments that will further improve the utilization and cost effectiveness of the NTF and other wind tunnels.

Energy Saving Melting and Revert Reduction Technology: Melting Efficiency in Die Casting Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Schwam

2012-12-15

This project addressed multiple aspects of the aluminum melting and handling in die casting operations, with the objective of increasing the energy efficiency while improving the quality of the molten metal. The efficiency of melting has always played an important role in the profitability of aluminum die casting operations. Consequently, die casters need to make careful choices in selecting and operating melting equipment and procedures. The capital cost of new melting equipment with higher efficiency can sometimes be recovered relatively fast when it replaces old melting equipment with lower efficiency. Upgrades designed to improve energy efficiency of existing equipment maymore » be well justified. Energy efficiency is however not the only factor in optimizing melting operations. Melt losses and metal quality are also very important. Selection of melting equipment has to take into consideration the specific conditions at the die casting shop such as availability of floor space, average quantity of metal used as well as the ability to supply more metal during peaks in demand. In all these cases, it is essential to make informed decisions based on the best available data.« less

Operational Issues: What Science in Available?

NASA Technical Reports Server (NTRS)

Rosekind, Mark R.; Neri, David F.

1997-01-01

Flight/duty/rest considerations involve two highly complex factors: the diverse demands of aviation operations and human physiology (especially sleep and circadian rhythms). Several core operational issues related to fatigue have been identified, such as minimum rest requirements, duty length, flight time considerations, crossing multiple time zones, and night flying. Operations also can involve on-call reserve status and callout, delays due to unforeseen circumstances (e.g., weather, mechanical), and on-demand flights. Over 40 years of scientific research is now available to apply to these complex issues of flight/duty/rest requirements. This research involves controlled 'laboratory studies, simulations, and data collected during regular flight operations. When flight/duty/rest requirements are determined they are typically based on a variety of considerations, such as operational demand, safety, economic, etc. Rarely has the available, state-of-the-art science been a consideration along with these other factors when determining flight/duty/rest requirements. While the complexity of the operational demand and human physiology precludes an absolute solution, there is an opportunity to take full advantage of the current scientific data. Incorporating these data in a rational operational manner into flight/duty/rest requirements can improve flight crew performance, alertness, and ultimately, aviation safety.

Integrating Emerging Data Sources into Operational Practice: Capabilities and Limitations of Devices to Collect, Compile, Save, and Share Messages from CAVs and Connected Travelers

DOT National Transportation Integrated Search

2018-03-01

Connected and automated vehicles (CAVs) and connected travelers will be providing substantially increased levels of data which will be available for agencies to consider using to improve the management and operation of the surface transportation syst...

A glove-likeability study of specially-treated gloves in the detonator manufacturing and packaging industry

DOE PAGES

Cournoyer, Michael E.; Lawton, Cindy M.; Lounsbury, James B.; ...

2016-03-22

We use hand gloves (hereafter referred to as gloves) in the detonator manufacturing and packaging operations. As part of a process improvement program, new glove formulations have been considered that lower the overall risk of detonator operations by reducing ergonomic injury factors. Gloves with a specially treated surface for extra grip and control are now commercially available and have been recommended for use in detonator operations. A Glove Likeability Study demonstrated that detonator manufacturing and packaging workers prefer gloves with a specially treated surface over currently approved gloves made from latex and nitrile formulations. Glove material compatibility tests indicate thatmore » the recommended gloves are as compatible if not more compatible as the currently approved gloves for working with secondary explosives. Thus, these gloves with a specially treated surface for extra grip and control are now available for tasks where sensitivity and fingertip control are crucial. Replacement of the current gloves with gloves with a specially treated surface improves the safety configuration of detonator manufacturing and packaging operations.« less

A glove-likeability study of specially-treated gloves in the detonator manufacturing and packaging industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cournoyer, Michael E.; Lawton, Cindy M.; Lounsbury, James B.

We use hand gloves (hereafter referred to as gloves) in the detonator manufacturing and packaging operations. As part of a process improvement program, new glove formulations have been considered that lower the overall risk of detonator operations by reducing ergonomic injury factors. Gloves with a specially treated surface for extra grip and control are now commercially available and have been recommended for use in detonator operations. A Glove Likeability Study demonstrated that detonator manufacturing and packaging workers prefer gloves with a specially treated surface over currently approved gloves made from latex and nitrile formulations. Glove material compatibility tests indicate thatmore » the recommended gloves are as compatible if not more compatible as the currently approved gloves for working with secondary explosives. Thus, these gloves with a specially treated surface for extra grip and control are now available for tasks where sensitivity and fingertip control are crucial. Replacement of the current gloves with gloves with a specially treated surface improves the safety configuration of detonator manufacturing and packaging operations.« less

Targeting and Localization for Mars Rover Operations

NASA Technical Reports Server (NTRS)

Powell, Mark W.; Crockett, Thomas; Fox, Jason M.; Joswig, Joseph C.; Norris, Jeffrey S.; Rabe, Kenneth J.; McCurdy, Michael; Pyrzak, Guy

2006-01-01

In this work we discuss how the quality of localization knowledge impacts the remote operation of rovers on the surface of Mars. We look at the techniques of localization estimation used in the Mars Pathfinder and Mars Exploration Rover missions. We examine the motivation behind the modes of targeting for different types of activities, such as navigation, remote science, and in situ science. We discuss the virtues and shortcomings of existing approaches and new improvements in the latest operations tools used to support the Mars Exploration Rover missions and rover technology development tasks at the Jet Propulsion Laboratory. We conclude with future directions we plan to explore in improving the localization knowledge available for operations and more effective targeting of rovers and their instrument payloads.

War Comes to Bala Morghab: A Tragedy of Policy and Action in Three Acts

DTIC Science & Technology

2011-12-01

real shower in December—a full 5 months after operations had commenced. The North Atlantic Treaty Organization (NATO) side of the FOB improved...Security Assistance Force (ISAF), Stability Operations Integration Cell ( SOIC ), “Murghab District, Badghis District Narrative Assessment, 5 May 2010...available at <http://publicintelligence. net/ufouo-stability-operations-information-center- soic -murghab-district-assessment/>. 3 Ibid. 4 Most facts

Capital planning for operating theatres based on projecting future theatre requirements.

PubMed

Sheehan, Jennifer A; Tyler, Peter; Jayasinha, Hirani; Meleady, Kathleen T; Jones, Neill

2011-05-01

During 2006, NSW and ACT Health Departments jointly engaged KPMG to develop an Operating Theatre Requirements' Projection Model and an accompanying planning guideline. A research scan was carried out to identify drivers of surgical demand, theatre capacity and theatre performance, as well as locating existing approaches to modelling operating theatre requirements for planning purposes. The project delivered a Microsoft Excel-based model for projecting future operating theatre requirements, together with an accompanying guideline for use of the model and interpretation of its outputs. It provides a valuable addition to the suite of tools available to Health staff for service and capital planning. The model operates with several limitations, largely due to being data dependent, and the state and completeness of available theatre activity data. However, the operational flexibility built into the model allows users to compensate for these limitations, on a case by case basis, when the user has access to suitable, local data. The design flexibility of the model means that updating the model as improved data become available is not difficult; resulting in revisions being able to be made quickly, and disseminated to users rapidly.

Improving the Long-Term Stability of Atmospheric Surface Deformation Predictions by Mitigating the Effects of Orography Updates in Operational Weather Forecast Models

NASA Astrophysics Data System (ADS)

Dill, Robert; Bergmann-Wolf, Inga; Thomas, Maik; Dobslaw, Henryk

2016-04-01

The global numerical weather prediction model routinely operated at the European Centre for Medium-Range Weather Forecasts (ECMWF) is typically updated about two times a year to incorporate the most recent improvements in the numerical scheme, the physical model or the data assimilation procedures into the system for steadily improving daily weather forecasting quality. Even though such changes frequently affect the long-term stability of meteorological quantities, data from the ECMWF deterministic model is often preferred over alternatively available atmospheric re-analyses due to both the availability of the data in near real-time and the substantially higher spatial resolution. However, global surface pressure time-series, which are crucial for the interpretation of geodetic observables, such as Earth rotation, surface deformation, and the Earth's gravity field, are in particular affected by changes in the surface orography of the model associated with every major change in horizontal resolution happened, e.g., in February 2006, January 2010, and May 2015 in case of the ECMWF operational model. In this contribution, we present an algorithm to harmonize surface pressure time-series from the operational ECMWF model by projecting them onto a time-invariant reference topography under consideration of the time-variable atmospheric density structure. The effectiveness of the method will be assessed globally in terms of pressure anomalies. In addition, we will discuss the impact of the method on predictions of crustal deformations based on ECMWF input, which have been recently made available by GFZ Potsdam.

Improving the environmental and performance characteristics of vehicles by introducing the surfactant additive into gasoline.

PubMed

Magaril, Elena; Magaril, Romen

2016-09-01

The operation of modern vehicles requires the introduction of package of fuel additives to ensure the required level of operating characteristics, some of which cannot be achieved by current oil refining methods. The use of additives allows flexibility of impact on the properties of the fuel at minimal cost, increasing the efficiency and environmental safety of vehicles. Among the wide assortment of additives available on the world market, many are surfactants. It has been shown that the introduction of some surfactants into gasoline concurrently reduces losses from gasoline evaporation, improves the mixture formation during injection of gasoline into the engine and improves detergent and anticorrosive properties. The surfactant gasoline additive that provides significant improvement in the quality of gasoline used and environmental and operating characteristics of vehicles has been developed and thoroughly investigated. The results of studies confirming the efficiency of the gasoline additive application are herein presented.

Development of Novel PEM Membrane and Multiphase CD Modeling of PEM Fuel Cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

K. J. Berry; Susanta Das

2009-12-30

To understand heat and water management phenomena better within an operational proton exchange membrane fuel cell's (PEMFC) conditions, a three-dimensional, two-phase computational fluid dynamic (CFD) flow model has been developed and simulated for a complete PEMFC. Both liquid and gas phases are considered in the model by taking into account the gas flow, diffusion, charge transfer, change of phase, electro-osmosis, and electrochemical reactions to understand the overall dynamic behaviors of species within an operating PEMFC. The CFD model is solved numerically under different parametric conditions in terms of water management issues in order to improve cell performance. The results obtainedmore » from the CFD two-phase flow model simulations show improvement in cell performance as well as water management under PEMFCs operational conditions as compared to the results of a single phase flow model available in the literature. The quantitative information obtained from the two-phase model simulation results helped to develop a CFD control algorithm for low temperature PEM fuel cell stacks which opens up a route in designing improvement of PEMFC for better operational efficiency and performance. To understand heat and water management phenomena better within an operational proton exchange membrane fuel cell's (PEMFC) conditions, a three-dimensional, two-phase computational fluid dynamic (CFD) flow model has been developed and simulated for a complete PEMFC. Both liquid and gas phases are considered in the model by taking into account the gas flow, diffusion, charge transfer, change of phase, electro-osmosis, and electrochemical reactions to understand the overall dynamic behaviors of species within an operating PEMFC. The CFD model is solved numerically under different parametric conditions in terms of water management issues in order to improve cell performance. The results obtained from the CFD two-phase flow model simulations show improvement in cell performance as well as water management under PEMFCs operational conditions as compared to the results of a single phase flow model available in the literature. The quantitative information obtained from the two-phase model simulation results helped to develop a CFD control algorithm for low temperature PEM fuel cell stacks which opens up a route in designing improvement of PEMFC for better operational efficiency and performance.« less

PV System 'Availability' as a Reliability Metric -- Improving Standards, Contract Language and Performance Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klise, Geoffrey T.; Hill, Roger; Walker, Andy

The use of the term 'availability' to describe a photovoltaic (PV) system and power plant has been fraught with confusion for many years. A term that is meant to describe equipment operational status is often omitted, misapplied or inaccurately combined with PV performance metrics due to attempts to measure performance and reliability through the lens of traditional power plant language. This paper discusses three areas where current research in standards, contract language and performance modeling is improving the way availability is used with regards to photovoltaic systems and power plants.

Corsair microcatheter for retrograde coronary chronic total occlusion recanalization: Early experience outside the realm of dedicated recanalization specialists

PubMed Central

Joseph, George; Thomson, Viji Samuel; Radhakrishnan, Shanmugasundaram

2012-01-01

Objective To determine the extent to which use of the Corsair microcatheter (CM, Asahi Intecc Co., Japan) improves procedural outcomes when an experienced operator who is not a dedicated recanalization specialist attempts retrograde chronic total occlusion (CTO) recanalization through collateral channels during percutaneous coronary intervention. Background The recently introduced CM has improved success rates of retrograde CTO recanalization to nearly 100% in the hands of dedicated coronary recanalization specialists; however, the impact the CM has on the results of non-specialist operators attempting retrograde CTO recanalization is not known. Methods A non-specialist operator attempted CM-assisted recanalization in seven consecutive CTO cases requiring retrograde recanalization. The results obtained were compared with those achieved by the same operator in eleven consecutive retrograde CTO recanalization procedures during the last 2 years before the CM became available. Results CM-assisted retrograde CTO recanalization was successful in 6 of 7 cases (86%), but failed in one case attempted through a tortuous epicardial collateral; there were no complications. In contrast, during the 2 years before the CM became available, retrograde CTO recanalization was successful in only 3 of 11 attempted cases (27%), and was associated with significant morbidity. Lesions in the two groups were comparable in terms of technical difficulty and procedural risk. Conclusions The non-specialist operator's retrograde CTO recanalization results improve significantly when using the CM. Given the effectiveness and safety of CM-assisted retrograde CTO recanalization, operators should be less aggressive with anterograde recanalization attempts, and should switch to the retrograde approach earlier and more often. PMID:22929822

Warfighter Support: Improved Cost Analysis and Better Oversight Needed over Army Nonstandard Equipment

DTIC Science & Technology

2011-09-01

to Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington VA 22202...making it available to Army units; when an item is deemed not operational , to dispose of it in theater; and to enter these instructions in a...is to continue to fund it with overseas contingency operations funds. In addition, the Army has no system to track, monitor, and manage its inventory

Addressing the medicinal chemistry bottleneck: a lean approach to centralized purification.

PubMed

Weller, Harold N; Nirschl, David S; Paulson, James L; Hoffman, Steven L; Bullock, William H

2012-09-10

The use of standardized lean manufacturing principles to improve drug discovery productivity is often thought to be at odds with fostering innovation. This manuscript describes how selective implementation of a lean optimized process, in this case centralized purification for medicinal chemistry, can improve operational productivity and increase scientist time available for innovation. A description of the centralized purification process is provided along with both operational and impact (productivity) metrics, which indicate lower cost, higher output, and presumably more free time for innovation as a result of the process changes described.

Making the most of data: An information selection and assessment framework to improve water systems operations

NASA Astrophysics Data System (ADS)

Giuliani, M.; Pianosi, F.; Castelletti, A.

2015-11-01

Advances in Environmental monitoring systems are making a wide range of data available at increasingly higher temporal and spatial resolution. This creates an opportunity to enhance real-time understanding of water systems conditions and to improve prediction of their future evolution, ultimately increasing our ability to make better decisions. Yet, many water systems are still operated using very simple information systems, typically based on simple statistical analysis and the operator's experience. In this work, we propose a framework to automatically select the most valuable information to inform water systems operations supported by quantitative metrics to operationally and economically assess the value of this information. The Hoa Binh reservoir in Vietnam is used to demonstrate the proposed framework in a multiobjective context, accounting for hydropower production and flood control. First, we quantify the expected value of perfect information, meaning the potential space for improvement under the assumption of exact knowledge of the future system conditions. Second, we automatically select the most valuable information that could be actually used to improve the Hoa Binh operations. Finally, we assess the economic value of sample information on the basis of the resulting policy performance. Results show that our framework successfully select information to enhance the performance of the operating policies with respect to both the competing objectives, attaining a 40% improvement close to the target trade-off selected as potentially good compromise between hydropower production and flood control.

Yield and Production Properties of Wood chips and Particles Torrefied in a Crucible Furnace Retort

Treesearch

Thomas L. Eberhardt; Chi-Leung So; Karen G. Reed

2016-01-01

Biomass preprocessing by torrefaction improves feedstock consistency and thereby improves the efficiency of biofuels operations, including pyrolysis, gasification, and combustion. A crucible furnace retort was fabricated of sufficient size to handle a commercially available wood chip feedstock. Varying the torrefaction times and temperatures provided an array of...

L-band microwave remote sensing and land data assimilation improve the representation of pre-storm soil moisture conditions for hydrologic forecasting

USDA-ARS?s Scientific Manuscript database

Recent advances in remote sensing and land data assimilation purport to improve the quality of antecedent soil moisture information available for operational hydrologic forecasting. We objectively validate this claim by calculating the strength of the relationship between storm-scale runoff ratio (i...

Microsurgical resection of skull base meningioma-expanding the operative corridor.

PubMed

Raheja, Amol; Couldwell, William T

2016-11-01

A better understanding of surgical anatomy, marked improvement in illumination devices, provision of improved hemostatic agents, greater availability of more precise surgical instruments, and better modalities for skull base reconstruction have led to an inevitable evolution of skull base neurosurgery. For the past few decades, many skull base neurosurgeons have worked relentlessly to improve the surgical approach and trajectory for the expansion of operative corridor. With the advent of newer techniques and their rapid adaptation, it is foundational, especially for young neurosurgeons, to understand the basics and nuances of modifications of traditional neurosurgical approaches. The goal of this topic review is to discuss the evolution of, concepts in, and technical nuances regarding the operative corridor expansion in the field of skull base surgery for intracranial meningioma as they pertain to achieving optimal functional outcome.

Use of Business Intelligence Tools in the DSN

NASA Technical Reports Server (NTRS)

Statman, Joseph I.; Zendejas, Silvino C.

2010-01-01

JPL has operated the Deep Space Network (DSN) on behalf of NASA since the 1960's. Over the last two decades, the DSN budget has generally declined in real-year dollars while the aging assets required more attention, and the missions became more complex. As a result, the DSN budget has been increasingly consumed by Operations and Maintenance (O&M), significantly reducing the funding wedge available for technology investment and for enhancing the DSN capability and capacity. Responding to this budget squeeze, the DSN launched an effort to improve the cost-efficiency of the O&M. In this paper we: elaborate on the methodology adopted to understand "where the time and money are used"-surprisingly, most of the data required for metrics development was readily available in existing databases-we have used commercial Business Intelligence (BI) tools to mine the databases and automatically extract the metrics (including trends) and distribute them weekly to interested parties; describe the DSN-specific effort to convert the intuitive understanding of "where the time is spent" into meaningful and actionable metrics that quantify use of resources, highlight candidate areas of improvement, and establish trends; and discuss the use of the BI-derived metrics-one of the most fascinating processes was the dramatic improvement in some areas of operations when the metrics were shared with the operators-the visibility of the metrics, and a self-induced competition, caused almost immediate improvement in some areas. While the near-term use of the metrics is to quantify the processes and track the improvement, these techniques will be just as useful in monitoring the process, e.g. as an input to a lean-six-sigma process.

Human Factors for Situation Assessment in Grid Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guttromson, Ross T.; Schur, Anne; Greitzer, Frank L.

2007-08-08

Executive Summary Despite advances in technology, power system operators must assimilate overwhelming amounts of data to keep the grid operating. Analyses of recent blackouts have clearly demonstrated the need to enhance the operator’s situation awareness (SA). The long-term objective of this research is to integrate valuable technologies into the grid operator environment that support decision making under normal and abnormal operating conditions and remove non-technical barriers to enable the optimum use of these technologies by individuals working alone and as a team. More specifically, the research aims to identify methods and principles to increase SA of grid operators in themore » context of system conditions that are representative or common across many operating entities and develop operationally relevant experimental methods for studying technologies and operational practices which contribute to SA. With increasing complexity and interconnectivity of the grid, the scope and complexity of situation awareness have grown. New paradigms are needed to guide research and tool development aimed to enhance and improve operations. In reviewing related research, operating practices, systems, and tools, the present study established a taxonomy that provides a perspective on research and development surrounding power grid situation awareness and clarifies the field of human factors/SA for grid operations. Information sources that we used to identify critical factors underlying SA included interviews with experienced operational personnel, available historical summaries and transcripts of abnormal conditions and outages (e.g., the August 14, 2003 blackout), scientific literature, and operational policies/procedures and other documentation. Our analysis of August 2003 blackout transcripts and interviews adopted a different perspective than previous analyses of this material, and we complemented this analysis with additional interviews. Based on our analysis and a broad literature review, we advocate a new perspective on SA in terms of sensemaking, also called situated or ecological decision making, where the focus of the investigation is to understand why the decision maker(s) experienced the situation the way they did, or why what they saw made sense to them at the time. This perspective is distinct from the traditional branch of human factors research in the field which focuses more on ergonomics and the transactional relationship between the human operator and the systems. Consistent with our findings from the literature review, we recognized an over-arching need to focus SA research on issues surrounding the concept of shared knowledge; e.g., awareness of what is happening in adjacent areas as well as one’s own area of responsibility. Major findings were: a) Inadequate communication/information sharing is pervasive, b) Information is available, but not used. Many tools and mechanisms exist for operators to build awareness of the physical grid system, yet the transcripts reveal that they still need to call and exchange information with operators of neighboring areas to improve or validate their SA. The specific types of information that they request are quite predictable and, in most cases, cover information that could be available to both operators and reliability coordinators through readily available displays or other data sources, c) Shared Knowledge is Required on Operations/Actions as Well as Physical Status. In an ideal, technologically and organizationally perfect world, every control room and every reliability coordinator may have access to complete data across all regional control areas and yet, there would still be reason for the operators to call each other to gain and improve their SA of power grid operations, and d) Situation Awareness as sensemaking and shared knowledge.« less

Operating room efficiency improvement after implementation of a postoperative team assessment.

PubMed

Porta, Christopher R; Foster, Andrew; Causey, Marlin W; Cordier, Patricia; Ozbirn, Roger; Bolt, Stephen; Allison, Dennis; Rush, Robert

2013-03-01

Operating room time is highly resource intensive, and delays can be a source of lost revenue and surgeon frustration. Methods to decrease these delays are important not only for patient care, but to maximize operating room resource utilization. The purpose of this study was to determine the root cause of operating room delays in a standardized manner to help improve overall operating room efficiency. We performed a single-center prospective observational study analyzing operating room utilization and efficiency after implementing an executive-driven standardized postoperative team debriefing system from January 2010 to December 2010. A total of 11,342 procedures were performed over the 1-y study period (elective 86%, urgent 11%, and emergent 3%), with 1.3 million min of operating room time, 865,864 min of surgeon operative time (62.5%), and 162,958 min of anesthesia time (11.8%). Overall, the average operating room delay was 18 min and varied greatly based on the surgical specialty. The longest delays were due to need for radiology (40 min); other significant delays were due to supply issues (22.7 min), surgeon issues (18 min), nursing issues (14 min), and room turnover (14 min). Over the 1-y period, there was a decrease in mean delay duration, averaging a decrease in delay of 0.147 min/mo with an overall 9% decrease in the mean delay times. With regard to overall operating room utilization, there was a 39% decrease in overall un-utilized available OR time that was due to delays, improving efficiency by 2334 min (212 min/mo). During this study interval no sentinel events occurred in the operating room. A standardized postoperative debrief tracking system is highly beneficial in identifying and reducing overall operative delays and improving operating room utilization. Published by Elsevier Inc.

[Intelligent operating room suite : From passive medical devices to the self-thinking cognitive surgical assistant].

PubMed

Kenngott, H G; Wagner, M; Preukschas, A A; Müller-Stich, B P

2016-12-01

Modern operating room (OR) suites are mostly digitally connected but until now the primary focus was on the presentation, transfer and distribution of images. Device information and processes within the operating theaters are barely considered. Cognitive assistance systems have triggered a fundamental rethinking in the automotive industry as well as in logistics. In principle, tasks in the OR, some of which are highly repetitive, also have great potential to be supported by automated cognitive assistance via a self-thinking system. This includes the coordination of the entire workflow in the perioperative process in both the operating theater and the whole hospital. With corresponding data from hospital information systems, medical devices and appropriate models of the surgical process, intelligent systems could optimize the workflow in the operating theater in the near future and support the surgeon. Preliminary results on the use of device information and automatically controlled OR suites are already available. Such systems include, for example the guidance of laparoscopic camera systems. Nevertheless, cognitive assistance systems that make use of knowledge about patients, processes and other pieces of information to improve surgical treatment are not yet available in the clinical routine but are urgently needed in order to automatically assist the surgeon in situation-related activities and thus substantially improve patient care.

Factors that Affect Operational Reliability of Turbojet Engines

NASA Technical Reports Server (NTRS)

1956-01-01

The problem of improving operational reliability of turbojet engines is studied in a series of papers. Failure statistics for this engine are presented, the theory and experimental evidence on how engine failures occur are described, and the methods available for avoiding failure in operation are discussed. The individual papers of the series are Objectives, Failure Statistics, Foreign-Object Damage, Compressor Blades, Combustor Assembly, Nozzle Diaphrams, Turbine Buckets, Turbine Disks, Rolling Contact Bearings, Engine Fuel Controls, and Summary Discussion.

Classroom Thought, Teacher Questions, and Student Analysis

ERIC Educational Resources Information Center

Wilen, William W.; Hogg, James

1976-01-01

Discussed is the need for teachers to improve their effectiveness in classroom skills such as questioning techniques. An instructor cognitive operation index is presented. For journal availability, see SO 505 192. (Author/DB)

How School Facilities Managers and Business Officials Are Reducing Operating Costs and Saving Money. Energy-Smart Building Choices.

ERIC Educational Resources Information Center

Department of Energy, Washington, DC.

This guide addresses contributions that school facility administrators and business officials can make in an effort to reduce operating costs and free up money for capital improvements. The guide explores opportunities available to utilize energy-saving strategies at any stage in a building's life, from its initial design phase through renovation.…

Corsair microcatheter for retrograde coronary chronic total occlusion recanalization: early experience outside the realm of dedicated recanalization specialists.

PubMed

Joseph, George; Thomson, Viji Samuel; Radhakrishnan, Shanmugasundaram

2012-01-01

To determine the extent to which use of the Corsair microcatheter (CM, Asahi Intecc Co., Japan) improves procedural outcomes when an experienced operator who is not a dedicated recanalization specialist attempts retrograde chronic total occlusion (CTO) recanalization through collateral channels during percutaneous coronary intervention. The recently introduced CM has improved success rates of retrograde CTO recanalization to nearly 100% in the hands of dedicated coronary recanalization specialists; however, the impact the CM has on the results of non-specialist operators attempting retrograde CTO recanalization is not known. A non-specialist operator attempted CM-assisted recanalization in seven consecutive CTO cases requiring retrograde recanalization. The results obtained were compared with those achieved by the same operator in eleven consecutive retrograde CTO recanalization procedures during the last 2 years before the CM became available. CM-assisted retrograde CTO recanalization was successful in 6 of 7 cases (86%), but failed in one case attempted through a tortuous epicardial collateral; there were no complications. In contrast, during the 2 years before the CM became available, retrograde CTO recanalization was successful in only 3 of 11 attempted cases (27%), and was associated with significant morbidity. Lesions in the two groups were comparable in terms of technical difficulty and procedural risk. The non-specialist operator's retrograde CTO recanalization results improve significantly when using the CM. Given the effectiveness and safety of CM-assisted retrograde CTO recanalization, operators should be less aggressive with anterograde recanalization attempts, and should switch to the retrograde approach earlier and more often. Copyright © 2012 Cardiological Society of India. Published by Elsevier B.V. All rights reserved.

LDAR, A Three-Dimensional Lightning Warning System: Its Development and Use by the Government, and Transition to Public Availability

NASA Technical Reports Server (NTRS)

Starr, Stan; Sharp, David; Merceret, Francis; Madura, John; Murphy, Martin

1998-01-01

NASA, at the John F. Kennedy Space Center (KSC), developed and operates a unique high precision lightning location system to provide lightning related weather warnings. These warnings are used to stop lightning-sensitive operations such as space vehicle launches and ground operations where equipment and personnel are at risk. The data is provided to the Range Weather Operations [45th Weather Squadron, U. S. Air Force (USAF)] where it is used with other meteorological data to issue weather advisories and warnings for Cape Canaveral Air Station (CCAS) and KSC operations. This system, called Lightning Detection and Ranging (LDAR), provides users with a graphical display in three dimensions of 66 MHz radio frequency events generated by lightning processes. The locations of these events provide a sound basis for the prediction of lightning hazards. NASA and Global Atmospherics, Inc. are developing a new system that will replace the unique LDAR components with commercially available and maintainable components having improved capabilities. These components will be phased in to ensure full continuity and access to this important warning technology. These LDAR systems are expected to eventually be available for installation and use by the public at specialized facilities, such as airports, and for general weather warnings via the National Weather Service (NWS) or television broadcast. The NWS in Melbourne has had access to real-time LDAR data since 1993 on an experimental basis. This use of LDAR has shown promise for the improvement of aviation forecasts and severe weather warnings. More so, it has opened the door to investigate the feasibility of issuing lightning-related public advisories. The success of its early use suggests that this technology may improve safety and potentially save lives, therefore constituting a significant benefit to the public. This paper describes the LDR system, the plans and progress of these upgrades, and the potential benefits of its use.

Improving the Management of Urban Research: City/University Co-Operation. OECD Urban Management Studies 5. Revised.

ERIC Educational Resources Information Center

Organisation for Economic Cooperation and Development, Paris (France).

The papers in this collection were presented at an international symposium on improving the management of urban research, particularly through city-university collaboration. An introductory framework paper summarizes the range of research services available to local government, the types of urban research activity, and the problems of urban…

An Integrated Tone Mapping for High Dynamic Range Image Visualization

NASA Astrophysics Data System (ADS)

Liang, Lei; Pan, Jeng-Shyang; Zhuang, Yongjun

2018-01-01

There are two type tone mapping operators for high dynamic range (HDR) image visualization. HDR image mapped by perceptual operators have strong sense of reality, but will lose local details. Empirical operators can maximize local detail information of HDR image, but realism is not strong. A common tone mapping operator suitable for all applications is not available. This paper proposes a novel integrated tone mapping framework which can achieve conversion between empirical operators and perceptual operators. In this framework, the empirical operator is rendered based on improved saliency map, which simulates the visual attention mechanism of the human eye to the natural scene. The results of objective evaluation prove the effectiveness of the proposed solution.

Perspectives of HIV agencies on improving HIV prevention, treatment, and care services in the USA.

PubMed

Khosla, Nidhi; Zachary, Iris

2016-10-01

HIV healthcare services in the USA are made available through a complex funding and delivery system. We present perspectives of HIV agencies on improvements that could lead to an ideal system of HIV prevention, treatment and care. We conducted semi-structured interviews with representatives from 21 HIV agencies offering diverse services in Baltimore, MD. Thematic analysis revealed six key themes: (1) Focusing on HIV prevention, (2) Establishing common entry-points for services, (3) Improving information availability, (4) Streamlining funding streams, (5) Removing competitiveness and (6) Building trust. We recommend that in addition to addressing operational issues regarding service delivery and patient care, initiatives to improve HIV service systems should address underlying social issues such as building trust.

Program of operation for the National Water Data Ex. (NAWDEX)

USGS Publications Warehouse

Edwards, M.D.

1985-01-01

The National Water Data Exchange (NAWDEX) has been established as a nationwide program directed at improving access to water and water-related data and disseminating information about the availability of these data throughout the entire water-resources community. NAWDEX is composed of a confederation of water-oriented organizations working together to facilitate the exchange of data and to improve the technology of data handling and transfer. This program of operation is directed at providing guidelines to assure that all member organizations participate equally and that a climate of cooperation and open communication be established among participating members.

Main improvements of LHC Cryogenics Operation during Run 2 (2015-2018)

NASA Astrophysics Data System (ADS)

Delprat, L.; Bradu, B.; Brodzinski, K.; Ferlin, G.; Hafi, K.; Herblin, L.; Rogez, E.; Suraci, A.

2017-12-01

After the successful Run 1 (2010-2012), the LHC entered its first Long Shutdown period (LS1, 2013-2014). During LS1 the LHC cryogenic system went under a complete maintenance and consolidation program. The LHC resumed operation in 2015 with an increased beam energy from 4 TeV to 6.5 TeV. Prior to the new physics Run 2 (2015-2018), the LHC was progressively cooled down from ambient to the 1.9 K operation temperature. The LHC has resumed operation with beams in April 2015. Operational margins on the cryogenic capacity were reduced compared to Run 1, mainly due to the observed higher than expected electron-cloud heat load coming from increased beam energy and intensity. Maintaining and improving the cryogenic availability level required the implementation of a series of actions in order to deal with the observed heat loads. This paper describes the results from the process optimization and update of the control system, thus allowing the adjustment of the non-isothermal heat load at 4.5 - 20 K and the optimized dynamic behaviour of the cryogenic system versus the electron-cloud thermal load. Effects from the new regulation settings applied for operation on the electrical distribution feed-boxes and inner triplets will be discussed. The efficiency of the preventive and corrective maintenance, as well as the benefits and issues of the present cryogenic system configuration for Run 2 operational scenario will be described. Finally, the overall availability results and helium management of the LHC cryogenic system during the 2015-2016 operational period will be presented.

Air medical referring customer satisfaction: a valuable insight.

PubMed

Fultz, J H; Coyle, C B; Reynolds, P W

1998-01-01

To remain competitive and survive, air medical programs must have a mechanism for obtaining customer feedback, especially when alternate transport options are available. The goal of this survey was to examine the air medical service's performance as perceived by customers requesting the transport. Surveys were mailed to 400 referring customers who had contact with the flight crew during the transition of patient care. The survey consisted of 16 statements evaluating the service by using a 4-point Likert scale, three demographic questions, one statement evaluating overall satisfaction, and two open-ended questions for comments or suggestions. Two hundred forty-four surveys were returned for a 61% responses rate. Results indicated referring customers are satisfied with the service provided Written comments and suggestions were divided into two categories, positive comments and suggestions for improvement. Three common themes were identified within the suggestions for improvement: crew rapport, communications, and operations. Suggested improvements were evaluated, and selected strategies were incorporated into program operation. Customer feedback furnishes valuable insight into their needs and perception of a service. Comments and suggestions for improvement can promote critical inquiry into service operation and provide a catalyst for improvement.

Benefit Opportunities for Integrated Surface and Airspace Departure Scheduling: A Study of Operations at Charlotte-Douglas International Airport

NASA Technical Reports Server (NTRS)

Coppenbarger, Rich; Jung, Yoon; Kozon, Tom; Farrahi, Amir; Malik, Wakar; Lee, Hanbong; Chevalley, Eric; Kistler, Matt

2016-01-01

NASA is collaborating with the FAA and aviation industry to develop and demonstrate new capabilities that integrate arrival, departure, and surface air-traffic operations. The concept relies on trajectory-based departure scheduling and collaborative decision making to reduce delays and uncertainties in taxi and climb operations. The paper describes the concept and benefit mechanisms aimed at improving flight efficiency and predictability while maintaining or improving operational throughput. The potential impact of the technology is studied and discussed through a quantitative analysis of relevant shortfalls at the site identified for initial deployment and demonstration in 2017: Charlotte-Douglas International Airport. Results from trajectory analysis indicate substantial opportunity to reduce taxi delays for both departures and arrivals by metering departures at the gate in a manner that maximizes throughput while adhering to takeoff restrictions due mostly to airspace constraints. Substantial taxi-out delay reduction is shown for flights subject to departure restrictions stemming from traffic flow management initiatives. Opportunities to improve the predictability of taxi, takeoff, and climb operations are examined and their potential impact on airline scheduling decisions and air-traffic forecasting is discussed. In addition, the potential to improve throughput with departure scheduling that maximizes use of available runway and airspace capacity is analyzed.

A Best Practice for Developing Availability Guarantee Language in Photovoltaic (PV) O&M Agreements.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klise, Geoffrey Taylor; Balfour, John

This document outlines the foundation for developing language that can be utilized in an Equipment Availability Guarantee, typically included in an O&M services agreement between a PV system or plant owner and an O&M services provider, or operator. Many of the current PV O&M service agreement Availability Guarantees are based on contracts used for traditional power generation, which create challenges for owners and operators due to the variable nature of grid-tied photovoltaic generating technologies. This report documents language used in early PV availability guarantees and presents best practices and equations that can be used to more openly communicate how themore » reliability of the PV system and plant equipment can be expressed in an availability guarantee. This work will improve the bankability of PV systems by providing greater transparency into the equipment reliability state to all parties involved in an O&M services contract.« less

Arterial intelligent transportation systems : infrastructure elements and traveler information requirements.

DOT National Transportation Integrated Search

2009-08-01

Applying Intelligent Transportation Systems (ITS) to arterial systems allows TxDOT to significantly enhance : transportation system operation efficiency and improve traffic mobility. However, no guidelines are available to : assist TxDOT staff in sel...

Darwin v. 2.0: an interpreted computer language for the biosciences.

PubMed

Gonnet, G H; Hallett, M T; Korostensky, C; Bernardin, L

2000-02-01

We announce the availability of the second release of Darwin v. 2.0, an interpreted computer language especially tailored to researchers in the biosciences. The system is a general tool applicable to a wide range of problems. This second release improves Darwin version 1.6 in several ways: it now contains (1) a larger set of libraries touching most of the classical problems from computational biology (pairwise alignment, all versus all alignments, tree construction, multiple sequence alignment), (2) an expanded set of general purpose algorithms (search algorithms for discrete problems, matrix decomposition routines, complex/long integer arithmetic operations), (3) an improved language with a cleaner syntax, (4) better on-line help, and (5) a number of fixes to user-reported bugs. Darwin is made available for most operating systems free of char ge from the Computational Biochemistry Research Group (CBRG), reachable at http://chrg.inf.ethz.ch. darwin@inf.ethz.ch

Cardiac surgery productivity and throughput improvements.

PubMed

Lehtonen, Juha-Matti; Kujala, Jaakko; Kouri, Juhani; Hippeläinen, Mikko

2007-01-01

The high variability in cardiac surgery length--is one of the main challenges for staff managing productivity. This study aims to evaluate the impact of six interventions on open-heart surgery operating theatre productivity. A discrete operating theatre event simulation model with empirical operation time input data from 2603 patients is used to evaluate the effect that these process interventions have on the surgery output and overtime work. A linear regression model was used to get operation time forecasts for surgery scheduling while it also could be used to explain operation time. A forecasting model based on the linear regression of variables available before the surgery explains 46 per cent operating time variance. The main factors influencing operation length were type of operation, redoing the operation and the head surgeon. Reduction of changeover time between surgeries by inducing anaesthesia outside an operating theatre and by reducing slack time at the end of day after a second surgery have the strongest effects on surgery output and productivity. A more accurate operation time forecast did not have any effect on output, although improved operation time forecast did decrease overtime work. A reduction in the operation time itself is not studied in this article. However, the forecasting model can also be applied to discover which factors are most significant in explaining variation in the length of open-heart surgery. The challenge in scheduling two open-heart surgeries in one day can be partly resolved by increasing the length of the day, decreasing the time between two surgeries or by improving patient scheduling procedures so that two short surgeries can be paired. A linear regression model is created in the paper to increase the accuracy of operation time forecasting and to identify factors that have the most influence on operation time. A simulation model is used to analyse the impact of improved surgical length forecasting and five selected process interventions on productivity in cardiac surgery.

How to improve an un-alterable model forecast? A sequential data assimilation based error updating approach

NASA Astrophysics Data System (ADS)

Gragne, A. S.; Sharma, A.; Mehrotra, R.; Alfredsen, K. T.

2012-12-01

Accuracy of reservoir inflow forecasts is instrumental for maximizing value of water resources and influences operation of hydropower reservoirs significantly. Improving hourly reservoir inflow forecasts over a 24 hours lead-time is considered with the day-ahead (Elspot) market of the Nordic exchange market in perspectives. The procedure presented comprises of an error model added on top of an un-alterable constant parameter conceptual model, and a sequential data assimilation routine. The structure of the error model was investigated using freely available software for detecting mathematical relationships in a given dataset (EUREQA) and adopted to contain minimum complexity for computational reasons. As new streamflow data become available the extra information manifested in the discrepancies between measurements and conceptual model outputs are extracted and assimilated into the forecasting system recursively using Sequential Monte Carlo technique. Besides improving forecast skills significantly, the probabilistic inflow forecasts provided by the present approach entrains suitable information for reducing uncertainty in decision making processes related to hydropower systems operation. The potential of the current procedure for improving accuracy of inflow forecasts at lead-times unto 24 hours and its reliability in different seasons of the year will be illustrated and discussed thoroughly.

Improved Operating Room Efficiency via Constraint Management: Experience of a Tertiary-Care Academic Medical Center.

PubMed

Kimbrough, Charles W; McMasters, Kelly M; Canary, Jeff; Jackson, Lisa; Farah, Ian; Boswell, Mark V; Kim, Daniel; Scoggins, Charles R

2015-07-01

Suboptimal operating room (OR) efficiency is a universal complaint among surgeons. Nonetheless, maximizing efficiency is critical to institutional success. Here, we report improvement achieved from low-cost, low-technology measures instituted within a tertiary-care academic medical center/Level I trauma center. Improvements in preadmission testing and OR scheduling, including appointing a senior nurse anesthetist to help direct OR use, were instituted in March 2012. A retrospective review of prospectively maintained OR case data was performed to evaluate time periods before and after program implementation, as well as to assess trends over time. Operating room performance metrics were compared using Mann-Whitney and chi-squared tests. Changes over time were analyzed using linear regression. Data including all surgical cases were available for a 36-month period; 10 months (6,581 cases) before program implementation and 26 months afterward (17,574 cases). Dramatic improvement was seen in first-case on-time starts, which increased from 39.3% to 83.8% (p < 0.0001). Additionally, the percent utilization of available OR time demonstrated a steady increase (p < 0.001). After an initial lag, case volume also improved, evident by an increase observed in the 12-month rolling average of cases per month (p < 0.001). The increase in case volume occurred during peak OR time (7 am to 5 pm), and did not result from adding cases after hours (5 pm to 11 pm). After many years of what seemed an insoluble problem, simple changes fostering collaboration among services, including active management of the OR schedule and transparent data, have resulted in substantial improvement in OR efficiency and case volume. Copyright © 2015 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

White Paper Number 2 for Improved Implementation of The Part 70 Operating Permits Program

EPA Pesticide Factsheets

This document may be of assistance in applying the Title V air operating permit regulations. This document is part of the Title V Policy and Guidance Database available at www2.epa.gov/title-v-operating-permits/title-v-operating-permit-policy-and-guidance-document-index. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

How Accurately do Leading and Lagging Indictors Predict F-16 Aircraft Availability (AA)

DTIC Science & Technology

2016-08-01

Predictions AU/ACSC/2016 vi PREFACE As the F-16 fleet continues to age, and budgets continue to shrink , United States Air Force (USAF... shrinking budgets, it is imperative for maintenance leaders to use all tools available to them to improve the amount of aircraft available for operations...remarkable considering the overall F-16 fleet shrinking at a steady pace (see table 2 for information). AA is one of the most critical factors that

Space Transportation Operations: Assessment of Methodologies and Models

NASA Technical Reports Server (NTRS)

Joglekar, Prafulla

2001-01-01

The systems design process for future space transportation involves understanding multiple variables and their effect on lifecycle metrics. Variables such as technology readiness or potential environmental impact are qualitative, while variables such as reliability, operations costs or flight rates are quantitative. In deciding what new design concepts to fund, NASA needs a methodology that would assess the sum total of all relevant qualitative and quantitative lifecycle metrics resulting from each proposed concept. The objective of this research was to review the state of operations assessment methodologies and models used to evaluate proposed space transportation systems and to develop recommendations for improving them. It was found that, compared to the models available from other sources, the operations assessment methodology recently developed at Kennedy Space Center has the potential to produce a decision support tool that will serve as the industry standard. Towards that goal, a number of areas of improvement in the Kennedy Space Center's methodology are identified.

Space Transportation Operations: Assessment of Methodologies and Models

NASA Technical Reports Server (NTRS)

Joglekar, Prafulla

2002-01-01

The systems design process for future space transportation involves understanding multiple variables and their effect on lifecycle metrics. Variables such as technology readiness or potential environmental impact are qualitative, while variables such as reliability, operations costs or flight rates are quantitative. In deciding what new design concepts to fund, NASA needs a methodology that would assess the sum total of all relevant qualitative and quantitative lifecycle metrics resulting from each proposed concept. The objective of this research was to review the state of operations assessment methodologies and models used to evaluate proposed space transportation systems and to develop recommendations for improving them. It was found that, compared to the models available from other sources, the operations assessment methodology recently developed at Kennedy Space Center has the potential to produce a decision support tool that will serve as the industry standard. Towards that goal, a number of areas of improvement in the Kennedy Space Center's methodology are identified.

Multivariate data analysis on historical IPV production data for better process understanding and future improvements.

PubMed

Thomassen, Yvonne E; van Sprang, Eric N M; van der Pol, Leo A; Bakker, Wilfried A M

2010-09-01

Historical manufacturing data can potentially harbor a wealth of information for process optimization and enhancement of efficiency and robustness. To extract useful data multivariate data analysis (MVDA) using projection methods is often applied. In this contribution, the results obtained from applying MVDA on data from inactivated polio vaccine (IPV) production runs are described. Data from over 50 batches at two different production scales (700-L and 1,500-L) were available. The explorative analysis performed on single unit operations indicated consistent manufacturing. Known outliers (e.g., rejected batches) were identified using principal component analysis (PCA). The source of operational variation was pinpointed to variation of input such as media. Other relevant process parameters were in control and, using this manufacturing data, could not be correlated to product quality attributes. The gained knowledge of the IPV production process, not only from the MVDA, but also from digitalizing the available historical data, has proven to be useful for troubleshooting, understanding limitations of available data and seeing the opportunity for improvements. 2010 Wiley Periodicals, Inc.

Assessing Performance of Multipurpose Reservoir System Using Two-Point Linear Hedging Rule

NASA Astrophysics Data System (ADS)

Sasireka, K.; Neelakantan, T. R.

2017-07-01

Reservoir operation is the one of the important filed of water resource management. Innovative techniques in water resource management are focussed at optimizing the available water and in decreasing the environmental impact of water utilization on the natural environment. In the operation of multi reservoir system, efficient regulation of the release to satisfy the demand for various purpose like domestic, irrigation and hydropower can lead to increase the benefit from the reservoir as well as significantly reduces the damage due to floods. Hedging rule is one of the emerging techniques in reservoir operation, which reduce the severity of drought by accepting number of smaller shortages. The key objective of this paper is to maximize the minimum power production and improve the reliability of water supply for municipal and irrigation purpose by using hedging rule. In this paper, Type II two-point linear hedging rule is attempted to improve the operation of Bargi reservoir in the Narmada basin in India. The results obtained from simulation of hedging rule is compared with results from Standard Operating Policy, the result shows that the application of hedging rule significantly improved the reliability of water supply and reliability of irrigation release and firm power production.

Steps for Action : getting intelligent transportation systems ready for the year 2000

DOT National Transportation Integrated Search

1998-09-01

Hazardous Materials Incident Response Cross-Cutting report summarizes and interprets the results of three Field Operational Tests (FOTs) that are evaluating systems for improving the accuracy and availability of HazMat information provided to emergen...

Project : transit demand and routing after autonomous vehicle availability.

DOT National Transportation Integrated Search

2015-12-01

Autonomous vehicles (AVs) create the potential for improvements in traffic operations as well as : new behaviors for travelers such as car sharing among trips through driverless repositioning. Most studies : on AVs have focused on technology or traff...

Computers and Libraries-A Reply

ERIC Educational Resources Information Center

Salton, Gerard

1971-01-01

A consideration of the various possibilities which are available for improving library operations and collection control makes it plain that the response of the library community ought to be towards greater cooperation among library centers and more extensive standardization. (31 references) (Author)

Improved control strategy for wind-powered refrigerated storage of apples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldwin, J.D.C.

1979-01-01

The need for an improved control strategy for the operation of a wind-powered refrigeration system for the storage of apples was investigated. The results are applicable to other systems which employ intermittently available power sources, battery and thermal storage, and an auxiliary, direct current power supply. Tests were conducted on the wind-powered refrigeration system at the Virginia Polytechnic Institute and State University Horticulture Research Farm in Blacksburg, Virginia. Tests were conducted on the individual components of the system. In situ windmill performance was also conducted. The results of these tests have been presented. An improved control strategy was developed tomore » improve the utilization of available wind energy and to reduce the need for electrical energy from an external source while maintaining an adequate apple storage environment.« less

Exploring the Relationship Between Surgical Capacity and Output in Ghana: Current Capacity Assessments May Not Tell the Whole Story.

PubMed

Stewart, Barclay T; Gyedu, Adam; Gaskill, Cameron; Boakye, Godfred; Quansah, Robert; Donkor, Peter; Volmink, Jimmy; Mock, Charles

2018-03-13

Capacity assessments serve as surrogates for surgical output in low- and middle-income countries where detailed registers do not exist. The relationship between surgical capacity and output was evaluated in Ghana to determine whether a more critical interpretation of capacity assessment data is needed on which to base health systems strengthening initiatives. A standardized surgical capacity assessment was performed at 37 hospitals nationwide using WHO guidelines; availability of 25 essential resources and capabilities was used to create a composite capacity score that ranged from 0 (no availability of essential resources) to 75 (constant availability) for each hospital. Data regarding the number of essential operations performed over 1 year, surgical specialties available, hospital beds, and functional operating rooms were also collected. The relationship between capacity and output was explored. The median surgical capacity score was 37 [interquartile range (IQR) 29-48; range 20-56]. The median number of essential operations per year was 1480 (IQR 736-1932) at first-level hospitals; 1545 operations (IQR 984-2452) at referral hospitals; and 11,757 operations (IQR 3769-21,256) at tertiary hospitals. Surgical capacity and output were not correlated (p > 0.05). Contrary to current understanding, surgical capacity assessments may not accurately reflect surgical output. To improve the validity of surgical capacity assessments and facilitate maximal use of available resources, other factors that influence output should also be considered, including demand-side factors; supply-side factors and process elements; and health administration and management factors.

Defense Acquisitions: Assessments of Selected Weapon Programs

DTIC Science & Technology

2010-03-01

improved availability for small terminals. It is to replace the Ultra High Frequency (UHF) Follow-On ( UFO ) satellite system currently in operation...of MUOS capabilities is time-critical due to the operational failures of two UFO satellites. The MUOS program has taken several steps to address...failures of two UFO satellites. Based on the current health of on-orbit satellites, UHF communication capabilities are predicted to fall below the

Zero Energy Schools: Designing for the Future: Zero Energy Ready K-12 Schools

DOE Office of Scientific and Technical Information (OSTI.GOV)

Torcellini, Paul A

Designing, building, and operating zero energy ready K-12 schools provides benefits for districts, students, and teachers. Optimizing energy efficiency is important in any building, but it's particularly important in K-12 schools. Many U.S. school districts struggle for funding, and improving a school building's energy efficiency can free up operational funds that may then be available for educational and other purposes.

Applying the Theory of Constraints (TOC) to the Component Section of Naval Aviation Depot (NADEP), North Island

DTIC Science & Technology

1992-12-01

current repair policies and procedures within this shop. We offer some ideas and suggestions for changing and improving existing operations and the...implementing and focusing continual improvements in Shop 93302 and ultimately in the depot as a whole. 20. DISTRIBUTION/AVAILABILITY OF ABSTRACT 21...used to evaluate current repair policies and procedures within this shop. We also offer some ideas and suggestions for changing and improving existing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sullivan, Kevin; Anasti, William; Fang, Yichuan

The main purpose of this project is to look at technologies and philosophies that would help reduce the costs of an Integrated Gasification Combined Cycle (IGCC) plant, increase its availability or do both. GE’s approach to this problem is to consider options in three different areas: 1) technology evaluations and development; 2) constructability approaches; and 3) design and operation methodologies. Five separate tasks were identified that fall under the three areas: Task 2 – Integrated Operations Philosophy; Task 3 – Slip Forming of IGCC Components; Task 4 – Modularization of IGCC Components; Task 5 – Fouling Removal; and Task 6more » – Improved Slag Handling. Overall, this project produced results on many fronts. Some of the ideas could be utilized immediately by those seeking to build an IGCC plant in the near future. These include the considerations from the Integrated Operations Philosophy task and the different construction techniques of Slip Forming and Modularization (especially if the proposed site is in a remote location or has a lack of a skilled workforce). Other results include ideas for promising technologies that require further development and testing to realize their full potential and be available for commercial operation. In both areas GE considers this project to be a success in identifying areas outside the core IGCC plant systems that are ripe for cost reduction and ity improvement opportunities.« less

Precursor Report of Data Needs and Recommended Practices for PV Plant Availability Operations and Maintenance Reporting.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, Roger R.; Klise, Geoffrey Taylor; Balfour, John R.

Characterizing the factors that affect reliability of a photovoltaic (PV) power plant is an important aspect of optimal asset management. This document describes the many factors that affect operation and maintenance (O&M) of a PV plant, identifies the data necessary to quantify those factors, and describes how data might be used by O&M service providers and others in the PV industry. This document lays out data needs from perspectives of reliability, availability, and key performance indicators and is intended to be a precursor for standardizing terminology and data reporting, which will improve data sharing, analysis, and ultimately PV plant performance.

Enhancements to the IBM version of COSMIC/NASTRAN

NASA Technical Reports Server (NTRS)

Brown, W. Keith

1989-01-01

Major improvements were made to the IBM version of COSMIC/NASTRAN by RPK Corporation under contract to IBM Corporation. These improvements will become part of COSMIC's IBM version and will be available in the second quarter of 1989. The first improvement is the inclusion of code to take advantage of IBM's new Vector Facility (VF) on its 3090 machines. The remaining improvements are modifications that will benefit all users as a result of the extended addressing capability provided by the MVS/XA operating system. These improvements include the availability of an in-memory data base that potentially eliminates the need for I/O to the PRIxx disk files. Another improvement is the elimination of multiple load modules that have to be loaded for every link switch within NASTRAN. The last improvement allows for NASTRAN to execute above the 16 mega-byte line. This improvement allows for NASTRAN to have access to 2 giga-bytes of memory for open core and the in-memory data base.

Solving nuts-and-bolts nuclear problems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olmstead, A.; Schoen, J.

1979-05-01

The Operations and Maintenance Information Service (MIS), created and operated by NUS Corp., was designed to improve plant availability through the exchange of practical information between nuclear plants and a return to an emphasis on the problem-solving process. MIS meetings cover a range of plant problems and have been unique in bringing the rapid feedback of information pertinent to the day-to-day working operation of a total plant. Much of the response is by telephone contact, although the monthly newsletter, semi-annual meetings, and scheduled plant visits are also helpful.

Deriving adaptive operating rules of hydropower reservoirs using time-varying parameters generated by the EnKF

NASA Astrophysics Data System (ADS)

Feng, Maoyuan; Liu, Pan; Guo, Shenglian; Shi, Liangsheng; Deng, Chao; Ming, Bo

2017-08-01

Operating rules have been used widely to decide reservoir operations because of their capacity for coping with uncertain inflow. However, stationary operating rules lack adaptability; thus, under changing environmental conditions, they cause inefficient reservoir operation. This paper derives adaptive operating rules based on time-varying parameters generated using the ensemble Kalman filter (EnKF). A deterministic optimization model is established to obtain optimal water releases, which are further taken as observations of the reservoir simulation model. The EnKF is formulated to update the operating rules sequentially, providing a series of time-varying parameters. To identify the index that dominates the variations of the operating rules, three hydrologic factors are selected: the reservoir inflow, ratio of future inflow to current available water, and available water. Finally, adaptive operating rules are derived by fitting the time-varying parameters with the identified dominant hydrologic factor. China's Three Gorges Reservoir was selected as a case study. Results show that (1) the EnKF has the capability of capturing the variations of the operating rules, (2) reservoir inflow is the factor that dominates the variations of the operating rules, and (3) the derived adaptive operating rules are effective in improving hydropower benefits compared with stationary operating rules. The insightful findings of this study could be used to help adapt reservoir operations to mitigate the effects of changing environmental conditions.

Feasibility Study of a Rotorcraft Health and Usage Monitoring System (HUMS): Results of Operator's Evaluation

NASA Technical Reports Server (NTRS)

Romero, Raylund; Summers, Harold; Cronkhite, James

1996-01-01

The objective was to evaluate the feasibility of a state-of-the-art health and usage monitoring system (HUMS) to provide monitoring of critical mechanical systems on the helicopter, including motors, drive train, engines, and life-limited components. The implementation of HUMS and cost integration with current maintenance procedures was assessed from the operator's viewpoint in order to achieve expected benefits from these systems, such as enhanced safety, reduced maintenance cost, and increased availability. An operational HUMS that was installed and operated under an independent flight trial program was used as a basis for this study. The HUMS equipment and software were commercially available. Based on the results of the feasibility study, the HUMS used in the flight trial program generally demonstrated a high level of reliability in monitoring the rotor system, engines, drive train, and life-limited components. The system acted as a sentinel to warn of impending failures. A worn tail rotor pitch bearing was detected by HUMS, which had the capability for self testing to diagnose system and sensor faults. Examples of potential payback to the operator with HUMS were identified, including reduced insurance cost through enhanced safety, lower operating costs derived from maintenance credits, increased aircraft availability, and improved operating efficiency. The interfacing of HUMS with current operational procedures was assessed to require only minimal revisions to the operator's maintenance manuals. Finally the success in realizing the potential benefits from HUMS technology was found to depend on the operator, helicopter manufacturer, regulator (FAA), and HUMS supplier working together.

The use of patient factors to improve the prediction of operative duration using laparoscopic cholecystectomy.

PubMed

Thiels, Cornelius A; Yu, Denny; Abdelrahman, Amro M; Habermann, Elizabeth B; Hallbeck, Susan; Pasupathy, Kalyan S; Bingener, Juliane

2017-01-01

Reliable prediction of operative duration is essential for improving patient and care team satisfaction, optimizing resource utilization and reducing cost. Current operative scheduling systems are unreliable and contribute to costly over- and underestimation of operative time. We hypothesized that the inclusion of patient-specific factors would improve the accuracy in predicting operative duration. We reviewed all elective laparoscopic cholecystectomies performed at a single institution between 01/2007 and 06/2013. Concurrent procedures were excluded. Univariate analysis evaluated the effect of age, gender, BMI, ASA, laboratory values, smoking, and comorbidities on operative duration. Multivariable linear regression models were constructed using the significant factors (p < 0.05). The patient factors model was compared to the traditional surgical scheduling system estimates, which uses historical surgeon-specific and procedure-specific operative duration. External validation was done using the ACS-NSQIP database (n = 11,842). A total of 1801 laparoscopic cholecystectomy patients met inclusion criteria. Female sex was associated with reduced operative duration (-7.5 min, p < 0.001 vs. male sex) while increasing BMI (+5.1 min BMI 25-29.9, +6.9 min BMI 30-34.9, +10.4 min BMI 35-39.9, +17.0 min BMI 40 + , all p < 0.05 vs. normal BMI), increasing ASA (+7.4 min ASA III, +38.3 min ASA IV, all p < 0.01 vs. ASA I), and elevated liver function tests (+7.9 min, p < 0.01 vs. normal) were predictive of increased operative duration on univariate analysis. A model was then constructed using these predictive factors. The traditional surgical scheduling system was poorly predictive of actual operative duration (R 2  = 0.001) compared to the patient factors model (R 2  = 0.08). The model remained predictive on external validation (R 2  = 0.14).The addition of surgeon as a variable in the institutional model further improved predictive ability of the model (R 2  = 0.18). The use of routinely available pre-operative patient factors improves the prediction of operative duration during cholecystectomy.

Tune-Up Your Fan Systems for Improved Performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fans are used extensively in commercial buildings and represent approximately 6% of total energy consumed by commercial buildings. The U.S. Department of Energy (DOE) estimates that fans in commercial buildings consume 158 billion kWh of electricity annually. Maintaining fan systems in proper condition provides energy savings and ensures a comfortable and healthy environment. While many fan systems have significant energy savings opportunities available through improvements in fan selection, system design, and operational practices, it is not always apparent when a fan system needs maintenance or what opportunities are available for improvements. This resource is designed for facility managers and maintenancemore » staff to provide easy-to-implement actionable guidance on fan efficiency measures for existing ducted air systems.« less

An oscilloscope spot intensifier, to improve photographic recordings of action potentials.

PubMed

Evans, M H

1985-06-01

A circuit diagram is shown for a semiconductor device to intensify the brightness of an oscilloscope during the rapidly rising and falling phases of signals such as action potentials. Brightening pulses proportional in amplitude to the rate of change in the Y-axis are available for connection to an oscilloscope with an external intensity ('Z') modulation input. The circuit requires one transistor, one dual operational amplifier and two single fast operational amplifiers.

A comparative analysis of the dissemination of best practice measures for key populations.

PubMed

Lundy, Jennifer; Santangelo, Jennifer; Rogers, Patrick; Kuehn, Lynn; Christensen, Sharon; Bournique, Judy; Mekhjian, Hagop; Kamal, Jyoti

2008-11-06

In collaboration with the department of Quality and Operations Improvement, Clinical Applications and the Information Warehouse, we have leveraged available Information Warehouse data to build a Best Practice Compliance Measurement Dashboard. This tool combines information from our operating room charting system, our order entry system and coding information from the patient billing and management system to provide 'previous day', data on a patients current course of treatment.

Proceedings of the Annual ONR/CADRC Decision-Support Workshop (6th), Held in Quantico, Virginia, on 8-9 Sep 2004. Interoperability

DTIC Science & Technology

2004-11-01

fixed schedule checkups and overhauls), Underway Replenishment (the goal being operation in sea states 3 and higher via technical improvements to...determine whether sufficient local resources are available to deal with current conditions. Scheduling Agent: Assists the Emergency Operations Bureau to...will commence per predefined schedule within 15 minutes) and subsequently alerts its subscribers that the rolling power blackout has commenced. The

Project inspection using mobile technology - phase I : an investigation into existing business processes and areas for improvement using mobile technology.

DOT National Transportation Integrated Search

2013-08-01

As mobile technology becomes widely available and affordable, transportation agencies can use this technology to : streamline operations involved within project inspection. This research, conducted in two phases, identified : opportunities for proces...

Flexible and adaptive water systems operations through more informed and dynamic decisions

NASA Astrophysics Data System (ADS)

Castelletti, A.; Giuliani, M.

2016-12-01

Timely adapting the operations of water systems to be resilient against rapid changes in both hydroclimatic and socioeconomic forcing is generally recommended as a part of planning and managing water resources under uncertain futures. A great opportunity to make the operations more flexible and adaptive is offered by the unprecedented amount of information that is becoming available to water system operators, providing a wide range of data at increasingly higher temporal and spatial resolution. Yet, many water systems are still operated using very simple information systems, typically based on basic statistical analysis and the operator's experience. In this work, we discuss the potential offered by incorporating improved information to enhance water systems operation and increase their ability of adapting to different external conditions and resolving potential conflicts across sectors. In particular, we focus on the use of different variables associated to different dynamics of the system (slow and fast) diversely impacting the operating objectives on the short-, medium- and long-term. The multi-purpose operations of the Hoa Binh reservoir in the Red River Basin (Vietnam) is used to demonstrate our approach. Numerical results show that our procedure is able to automatically select the most valuable information for improving the Hoa Binh operations and mitigating the conflict between short-term objectives, i.e. hydropower production and flood control. Moreover, we also successfully identify low-frequency climate information associated to El-Nino Southern Oscillation for improving the performance in terms of long-term objectives, i.e. water supply. Finally, we assess the value of better informing operational decisions for adapting the system operations to changing conditions by considering different climate change projections.

Surface energy and radiation balance systems - General description and improvements

NASA Technical Reports Server (NTRS)

Fritschen, Leo J.; Simpson, James R.

1989-01-01

Surface evaluation of sensible and latent heat flux densities and the components of the radiation balance were desired for various vegetative surfaces during the ASCOT84 experiment to compare with modeled results and to relate these values to drainage winds. Five battery operated data systems equipped with sensors to determine the above values were operated for 105 station days during the ASCOT84 experiment. The Bowen ratio energy balance technique was used to partition the available energy into the sensible and latent heat flux densities. A description of the sensors and battery operated equipment used to collect and process the data is presented. In addition, improvements and modifications made since the 1984 experiment are given. Details of calculations of soil heat flow at the surface and an alternate method to calculate sensible and latent heat flux densities are provided.

Genetic Algorithm Application in Optimization of Wireless Sensor Networks

PubMed Central

Norouzi, Ali; Zaim, A. Halim

2014-01-01

There are several applications known for wireless sensor networks (WSN), and such variety demands improvement of the currently available protocols and the specific parameters. Some notable parameters are lifetime of network and energy consumption for routing which play key role in every application. Genetic algorithm is one of the nonlinear optimization methods and relatively better option thanks to its efficiency for large scale applications and that the final formula can be modified by operators. The present survey tries to exert a comprehensive improvement in all operational stages of a WSN including node placement, network coverage, clustering, and data aggregation and achieve an ideal set of parameters of routing and application based WSN. Using genetic algorithm and based on the results of simulations in NS, a specific fitness function was achieved, optimized, and customized for all the operational stages of WSNs. PMID:24693235

A database for coconut crop improvement

PubMed Central

Rajagopal, Velamoor; Manimekalai, Ramaswamy; Devakumar, Krishnamurthy; Rajesh; Karun, Anitha; Niral, Vittal; Gopal, Murali; Aziz, Shamina; Gunasekaran, Marimuthu; Kumar, Mundappurathe Ramesh; Chandrasekar, Arumugam

2005-01-01

Coconut crop improvement requires a number of biotechnology and bioinformatics tools. A database containing information on CG (coconut germplasm), CCI (coconut cultivar identification), CD (coconut disease), MIFSPC (microbial information systems in plantation crops) and VO (vegetable oils) is described. The database was developed using MySQL and PostgreSQL running in Linux operating system. The database interface is developed in PHP, HTML and JAVA. Availability http://www.bioinfcpcri.org PMID:17597858

Operationally Responsive Space: Creating Responsive Space for America

DTIC Science & Technology

2008-06-20

programs. Items identified for improvement include: 1 ) Fractured management and accounting , 2 ) Satellite availability, 3) Facilities (Processing...enveloped by our three output tiers. The three tiers: • Tier 1 is an immediate response taking minutes to days. • Tier 2 is a mid term response taking...needs to improve. 2 . Develop a philosophy. 3. Set a direction with specific goals (Fuchs 1 -7). The Department of Space should follow these

The Operation IceBridge Sea Ice Freeboard, Snow Septh and Thickness Product: An In-Depth Look at Past, Current and Future Versions

NASA Astrophysics Data System (ADS)

Harbeck, J.; Kurtz, N. T.; Studinger, M.; Onana, V.; Yi, D.

2015-12-01

The NASA Operation IceBridge Project Science Office has recently released an updated version of the sea ice freeboard, snow depth and thickness product (IDCSI4). This product is generated through the combination of multiple IceBridge instrument data, primarily the ATM laser altimeter, DMS georeferenced imagery and the CReSIS snow radar, and is available on a campaign-specific basis as all upstream data sets become available. Version 1 data (IDCSI2) was the initial data production; we have subsequently received community feedback that has now been incorporated, allowing us to provide an improved data product. All data now available to the public at the National Snow and Ice Data Center (NSIDC) have been homogeneously reprocessed using the new IDCSI4 algorithm. This algorithm contains significant upgrades that improve the quality and consistency of the dataset, including updated atmospheric and oceanic tidal models and replacement of the geoid with a more representative mean sea surface height product. Known errors with the IDCSI2 algorithm, identified by the Project Science Office as well as feedback from the scientific community, have been incorporated into the new algorithm as well. We will describe in detail the various steps of the IDCSI4 algorithm, show the improvements made over the IDCSI2 dataset and their beneficial impact and discuss future upgrades planned for the next version.

Reliability and Maintainability Analysis of a High Air Pressure Compressor Facility

NASA Technical Reports Server (NTRS)

Safie, Fayssal M.; Ring, Robert W.; Cole, Stuart K.

2013-01-01

This paper discusses a Reliability, Availability, and Maintainability (RAM) independent assessment conducted to support the refurbishment of the Compressor Station at the NASA Langley Research Center (LaRC). The paper discusses the methodologies used by the assessment team to derive the repair by replacement (RR) strategies to improve the reliability and availability of the Compressor Station (Ref.1). This includes a RAPTOR simulation model that was used to generate the statistical data analysis needed to derive a 15-year investment plan to support the refurbishment of the facility. To summarize, study results clearly indicate that the air compressors are well past their design life. The major failures of Compressors indicate that significant latent failure causes are present. Given the occurrence of these high-cost failures following compressor overhauls, future major failures should be anticipated if compressors are not replaced. Given the results from the RR analysis, the study team recommended a compressor replacement strategy. Based on the data analysis, the RR strategy will lead to sustainable operations through significant improvements in reliability, availability, and the probability of meeting the air demand with acceptable investment cost that should translate, in the long run, into major cost savings. For example, the probability of meeting air demand improved from 79.7 percent for the Base Case to 97.3 percent. Expressed in terms of a reduction in the probability of failing to meet demand (1 in 5 days to 1 in 37 days), the improvement is about 700 percent. Similarly, compressor replacement improved the operational availability of the facility from 97.5 percent to 99.8 percent. Expressed in terms of a reduction in system unavailability (1 in 40 to 1 in 500), the improvement is better than 1000 percent (an order of magnitude improvement). It is worthy to note that the methodologies, tools, and techniques used in the LaRC study can be used to evaluate similar high value equipment components and facilities. Also, lessons learned in data collection and maintenance practices derived from the observations, findings, and recommendations of the study are extremely important in the evaluation and sustainment of new compressor facilities.

Defense Logistics: Actions Needed to Improve the Availability of Critical Items during Current and Future Operations

DTIC Science & Technology

2005-04-01

process to promptly move supplies from the United States to a customer. GAO found that conflicting doctrinal responsibilities for distribution ... management , improperly packed shipments, insufficient transportation personnel and equipment, and inadequate information systems prevented the timely

Implementing bright light treatment for MSFC payload operations shiftworkers

NASA Technical Reports Server (NTRS)

Hayes, Benita C.; Stewart, Karen T.; Eastman, Charmane I.

1994-01-01

Intense light can phase-shift circadian rhythms and improve performance, sleep, and wellbeing during shiftwork simulations, but to date there have been very few attempts to administer light treatment to real shiftworkers. We have developed procedures for implementing light treatment and have conducted controlled trials of light treatment for MSFC Payload Operations staff during the USML-1 mission. We found that treatment had beneficial effects on fatigue, alertness, self-rated job performance, sleep, mood, and work attendance. Although there are portable bright light boxes commercially available, there is no testing protocol and little performance information available. We measure the illuminance of two candidate boxes for use in this study and found that levels were consistently lower than those advertised by manufacturers. A device was developed to enhance the illuminance output of such units. This device increased the illuminance by at least 60 % and provided additional improvements in visual comfort and overall exposure. Both the design of this device and some suggested procedures for evaluating light devices are presented.

Electric Dipole Moment Results from lattice QCD

NASA Astrophysics Data System (ADS)

Dragos, Jack; Luu, Thomas; Shindler, Andrea; de Vries, Jordy

2018-03-01

We utilize the gradient flow to define and calculate electric dipole moments induced by the strong QCD θ-term and the dimension-6 Weinberg operator. The gradient flow is a promising tool to simplify the renormalization pattern of local operators. The results of the nucleon electric dipole moments are calculated on PACS-CS gauge fields (available from the ILDG) using Nf = 2+1, of discrete size 323×64 and spacing a ≃ 0.09 fm. These gauge fields use a renormalization-group improved gauge action and a nonperturbatively O(a) improved clover quark action at β = 1.90, with cSW = 1.715. The calculation is performed at pion masses of mπ ≃ 411, 701 MeV.

Operation Program for the Spatially Phase-Shifted Digital Speckle Pattern Interferometer - SPS-DSPI

NASA Technical Reports Server (NTRS)

Blake, Peter N.; Jones, Joycelyn T.; Hostetter, Carl F.; Greenfield, Perry; Miller, Todd

2010-01-01

SPS-DSPI software has been revised so that Goddard optical engineers can operate the instrument, instead of data programmers. The user interface has been improved to view the data collected by the SPS-DSPI, with a real-time mode and a play-back mode. The SPS-DSPI has been developed by NASA/GSFC to measure the temperature distortions of the primary-mirror backplane structure for the James Webb Space Telescope. It requires a team of computer specialists to run successfully, because, at the time of this reporting, it just finished the prototype stage. This software improvement will transition the instrument to become available for use by many programs that measure distortion

Bandwidth Enabled Flight Operations: Examining the Possibilities

NASA Technical Reports Server (NTRS)

Pisanich, Greg; Renema, Fritz; Clancy, Dan (Technical Monitor)

2002-01-01

The Bandwidth Enabled Flight Operations project is a research effort at the NASA Ames Research Center to investigate the use of satellite communications to improve aviation safety and capacity. This project is a follow on to the AeroSAPIENT Project, which demonstrated methods for transmitting high bandwidth data in various configurations. For this research, we set a goal to nominally use only 10 percent of the available bandwidth demonstrated by AeroSAPIENT or projected by near-term technology advances. This paper describes the results of our research, including available satellite bandwidth, commercial and research efforts to provide these services, and some of the limiting factors inherent with this communications medium. It also describes our investigation into the needs of the stakeholders (Airlines, Pilots, Cabin Crews, ATC, Maintenance, etc). The paper also describes our development of low-cost networked flight deck and airline operations center simulations that were used to demonstrate two application areas: Providing real time weather information to the commercial flight deck, and enhanced crew monitoring and control for airline operations centers.

Peri-operative interventions producing better functional outcomes and enhanced recovery following total hip and knee arthroplasty: an evidence-based review

PubMed Central

2013-01-01

The increasing numbers of patients undergoing total hip arthroplasty (THA) or total knee arthroplasty (TKA), combined with the rapidly growing repertoire of surgical techniques and interventions available have put considerable pressure on surgeons and other healthcare professionals to produce excellent results with early functional recovery and short hospital stays. The current economic climate and the restricted healthcare budgets further necessitate brief hospitalization while minimizing costs. Clinical pathways and protocols introduced to achieve these goals include a variety of peri-operative interventions to fulfill patient expectations and achieve the desired outcomes. In this review, we present an evidence-based summary of common interventions available to achieve enhanced recovery, reduce hospital stay, and improve functional outcomes following THA and TKA. It covers pre-operative patient education and nutrition, pre-emptive analgesia, neuromuscular electrical stimulation, pulsed electromagnetic fields, peri-operative rehabilitation, modern wound dressings, standard surgical techniques, minimally invasive surgery, and fast-track arthroplasty units. PMID:23406499

Robotic inspection for vehicle-borne contraband

NASA Astrophysics Data System (ADS)

Witus, Gary; Gerhart, Grant; Smuda, W.; Andrusz, H.

2006-05-01

Vehicle-borne smuggling is widespread because of the availability, flexibility and capacity of the cars and trucks. Inspecting vehicles at border crossings and checkpoints are key security elements. At the present time, most vehicle security inspections at home and abroad are conducted manually. Remotely operated vehicle inspection robots could be integrated into the operating procedures to improve throughput while reducing the workload burden on security personnel. The robotic inspection must be effective at detecting contraband and efficient at clearing the "clean" vehicles that make up the bulk of the traffic stream, while limiting the workload burden on the operators. In this paper, we present a systems engineering approach to robotic vehicle inspection. We review the tactics, techniques and procedures to interdict contraband. We present an operational concept for robotic vehicle inspection within this framework, and identify needed capabilities. We review the technologies currently available to meet these needs. Finally, we summarize the immediate potential and R&D challenges for effective contraband detection robots.

Ensemble Flow Forecasts for Risk Based Reservoir Operations of Lake Mendocino in Mendocino County, California: A Framework for Objectively Leveraging Weather and Climate Forecasts in a Decision Support Environment

NASA Astrophysics Data System (ADS)

Delaney, C.; Hartman, R. K.; Mendoza, J.; Whitin, B.

2017-12-01

Forecast informed reservoir operations (FIRO) is a methodology that incorporates short to mid-range precipitation and flow forecasts to inform the flood operations of reservoirs. The Ensemble Forecast Operations (EFO) alternative is a probabilistic approach of FIRO that incorporates ensemble streamflow predictions (ESPs) made by NOAA's California-Nevada River Forecast Center (CNRFC). With the EFO approach, release decisions are made to manage forecasted risk of reaching critical operational thresholds. A water management model was developed for Lake Mendocino, a 111,000 acre-foot reservoir located near Ukiah, California, to evaluate the viability of the EFO alternative to improve water supply reliability but not increase downstream flood risk. Lake Mendocino is a dual use reservoir, which is owned and operated for flood control by the United States Army Corps of Engineers and is operated for water supply by the Sonoma County Water Agency. Due to recent changes in the operations of an upstream hydroelectric facility, this reservoir has suffered from water supply reliability issues since 2007. The EFO alternative was simulated using a 26-year (1985-2010) ESP hindcast generated by the CNRFC. The ESP hindcast was developed using Global Ensemble Forecast System version 10 precipitation reforecasts processed with the Hydrologic Ensemble Forecast System to generate daily reforecasts of 61 flow ensemble members for a 15-day forecast horizon. Model simulation results demonstrate that the EFO alternative may improve water supply reliability for Lake Mendocino yet not increase flood risk for downstream areas. The developed operations framework can directly leverage improved skill in the second week of the forecast and is extendable into the S2S time domain given the demonstration of improved skill through a reliable reforecast of adequate historical duration and consistent with operationally available numerical weather predictions.

Software Application Profile: Opal and Mica: open-source software solutions for epidemiological data management, harmonization and dissemination

PubMed Central

Doiron, Dany; Marcon, Yannick; Fortier, Isabel; Burton, Paul; Ferretti, Vincent

2017-01-01

Abstract Motivation Improving the dissemination of information on existing epidemiological studies and facilitating the interoperability of study databases are essential to maximizing the use of resources and accelerating improvements in health. To address this, Maelstrom Research proposes Opal and Mica, two inter-operable open-source software packages providing out-of-the-box solutions for epidemiological data management, harmonization and dissemination. Implementation Opal and Mica are two standalone but inter-operable web applications written in Java, JavaScript and PHP. They provide web services and modern user interfaces to access them. General features Opal allows users to import, manage, annotate and harmonize study data. Mica is used to build searchable web portals disseminating study and variable metadata. When used conjointly, Mica users can securely query and retrieve summary statistics on geographically dispersed Opal servers in real-time. Integration with the DataSHIELD approach allows conducting more complex federated analyses involving statistical models. Availability Opal and Mica are open-source and freely available at [www.obiba.org] under a General Public License (GPL) version 3, and the metadata models and taxonomies that accompany them are available under a Creative Commons licence. PMID:29025122

The 77 K operation of a multi-resonant power converter

NASA Technical Reports Server (NTRS)

Ray, Biswajit; Gerber, Scott S.; Patterson, Richard L.; Myers, Ira T.

1995-01-01

The liquid-nitrogen temperature (77 K) operation of a 55 W, 200 kHz, 48/28 V zero-voltage switching multi-resonant dc/dc converter designed with commercially available components is reported. Upon dipping the complete converter (power and control circuits) into liquid-nitrogen, the converter performance improved as compared to the room-temperature operation. The switching frequency, resonant frequency, and the characteristic impedance did not change significantly. Accordingly, the zero-voltage switching was maintained from no-load to full-load for the specified line variations. Cryoelectronics can provide high density power converters, especially for high power applications.

Building a computer-aided design capability using a standard time share operating system

NASA Technical Reports Server (NTRS)

Sobieszczanski, J.

1975-01-01

The paper describes how an integrated system of engineering computer programs can be built using a standard commercially available operating system. The discussion opens with an outline of the auxiliary functions that an operating system can perform for a team of engineers involved in a large and complex task. An example of a specific integrated system is provided to explain how the standard operating system features can be used to organize the programs into a simple and inexpensive but effective system. Applications to an aircraft structural design study are discussed to illustrate the use of an integrated system as a flexible and efficient engineering tool. The discussion concludes with an engineer's assessment of an operating system's capabilities and desirable improvements.

Water Use Optimization Toolset Project: Development and Demonstration Phase Draft Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasper, John R.; Veselka, Thomas D.; Mahalik, Matthew R.

2014-05-19

This report summarizes the results of the development and demonstration phase of the Water Use Optimization Toolset (WUOT) project. It identifies the objective and goals that guided the project, as well as demonstrating potential benefits that could be obtained by applying the WUOT in different geo-hydrologic systems across the United States. A major challenge facing conventional hydropower plants is to operate more efficiently while dealing with an increasingly uncertain water-constrained environment and complex electricity markets. The goal of this 3-year WUOT project, which is funded by the U.S. Department of Energy (DOE), is to improve water management, resulting in moremore » energy, revenues, and grid services from available water, and to enhance environmental benefits from improved hydropower operations and planning while maintaining institutional water delivery requirements. The long-term goal is for the WUOT to be used by environmental analysts and deployed by hydropower schedulers and operators to assist in market, dispatch, and operational decisions.« less

Fitting primitive shapes in point clouds: a practical approach to improve autonomous underwater grasp specification of unknown objects

NASA Astrophysics Data System (ADS)

Fornas, D.; Sales, J.; Peñalver, A.; Pérez, J.; Fernández, J. J.; Marín, R.; Sanz, P. J.

2016-03-01

This article presents research on the subject of autonomous underwater robot manipulation. Ongoing research in underwater robotics intends to increase the autonomy of intervention operations that require physical interaction in order to achieve social benefits in fields such as archaeology or biology that cannot afford the expenses of costly underwater operations using remote operated vehicles. Autonomous grasping is still a very challenging skill, especially in underwater environments, with highly unstructured scenarios, limited availability of sensors and adverse conditions that affect the robot perception and control systems. To tackle these issues, we propose the use of vision and segmentation techniques that aim to improve the specification of grasping operations on underwater primitive shaped objects. Several sources of stereo information are used to gather 3D information in order to obtain a model of the object. Using a RANSAC segmentation algorithm, the model parameters are estimated and a set of feasible grasps are computed. This approach is validated in both simulated and real underwater scenarios.

NASA Space Technology Draft Roadmap Area 13: Ground and Launch Systems Processing

NASA Technical Reports Server (NTRS)

Clements, Greg

2011-01-01

This slide presentation reviews the technology development roadmap for the area of ground and launch systems processing. The scope of this technology area includes: (1) Assembly, integration, and processing of the launch vehicle, spacecraft, and payload hardware (2) Supply chain management (3) Transportation of hardware to the launch site (4) Transportation to and operations at the launch pad (5) Launch processing infrastructure and its ability to support future operations (6) Range, personnel, and facility safety capabilities (7) Launch and landing weather (8) Environmental impact mitigations for ground and launch operations (9) Launch control center operations and infrastructure (10) Mission integration and planning (11) Mission training for both ground and flight crew personnel (12) Mission control center operations and infrastructure (13) Telemetry and command processing and archiving (14) Recovery operations for flight crews, flight hardware, and returned samples. This technology roadmap also identifies ground, launch and mission technologies that will: (1) Dramatically transform future space operations, with significant improvement in life-cycle costs (2) Improve the quality of life on earth, while exploring in co-existence with the environment (3) Increase reliability and mission availability using low/zero maintenance materials and systems, comprehensive capabilities to ascertain and forecast system health/configuration, data integration, and the use of advanced/expert software systems (4) Enhance methods to assess safety and mission risk posture, which would allow for timely and better decision making. Several key technologies are identified, with a couple of slides devoted to one of these technologies (i.e., corrosion detection and prevention). Development of these technologies can enhance life on earth and have a major impact on how we can access space, eventually making routine commercial space access and improve building and manufacturing, and weather forecasting for example for the effect of these process improvements on our daily lives.

Reasons for operation cancellations at a teaching hospital: prioritizing areas of improvement.

PubMed

Abeeleh, Mahmoud Abu; Tareef, Tareq M; Hani, Amjad Bani; Albsoul, Nader; Samarah, Omar Q; ElMohtaseb, M S; Alshehabat, Musa; Ismail, Zuhair Bani; Alnoubani, Omar; Obeidat, Salameh S; Halawa, Sami Abu

2017-08-01

To report rates of and reasons for operation cancellation, and to prioritize areas of improvement. Retrospective data were extracted from the monthly reports of cancelled listed operations. Data on 14 theatres were collected by the office of quality assurance at Jordan University Hospital from August 2012 to April 2016. Rates and reasons for operation cancellation were investigated. A Pareto chart was constructed to identify the reasons of highest priority. During the period of study, 6,431 cases (9.31%) were cancelled out of 69,066 listed cases. Patient no-shows accounted for 62.52% of cancellations. A Pareto analysis showed that around 80% of the known reasons for cancellation after admission were due to a lack of surgical theatre time (30%), incomplete preoperative assessment (21%), upper respiratory tract infection (19%), and high blood pressure (13%). This study identified the most common reasons for operation cancellation at a teaching hospital. Potential avoidable root causes and recommended interventions were suggested accordingly. Future research, available resources, hospital policies, and strategic measures directed to tackle these reasons should take priority.

Improving Distribution Resiliency with Microgrids and State and Parameter Estimation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tuffner, Francis K.; Williams, Tess L.; Schneider, Kevin P.

Modern society relies on low-cost reliable electrical power, both to maintain industry, as well as provide basic social services to the populace. When major disturbances occur, such as Hurricane Katrina or Hurricane Sandy, the nation’s electrical infrastructure can experience significant outages. To help prevent the spread of these outages, as well as facilitating faster restoration after an outage, various aspects of improving the resiliency of the power system are needed. Two such approaches are breaking the system into smaller microgrid sections, and to have improved insight into the operations to detect failures or mis-operations before they become critical. Breaking themore » system into smaller sections of microgrid islands, power can be maintained in smaller areas where distribution generation and energy storage resources are still available, but bulk power generation is no longer connected. Additionally, microgrid systems can maintain service to local pockets of customers when there has been extensive damage to the local distribution system. However, microgrids are grid connected a majority of the time and implementing and operating a microgrid is much different than when islanded. This report discusses work conducted by the Pacific Northwest National Laboratory that developed improvements for simulation tools to capture the characteristics of microgrids and how they can be used to develop new operational strategies. These operational strategies reduce the cost of microgrid operation and increase the reliability and resilience of the nation’s electricity infrastructure. In addition to the ability to break the system into microgrids, improved observability into the state of the distribution grid can make the power system more resilient. State estimation on the transmission system already provides great insight into grid operations and detecting abnormal conditions by leveraging existing measurements. These transmission-level approaches are expanded to using advanced metering infrastructure and other distribution-level measurements to create a three-phase, unbalanced distribution state estimation approach. With distribution-level state estimation, the grid can be operated more efficiently, and outages or equipment failures can be caught faster, improving the overall resilience and reliability of the grid.« less

A survey of Bolivian lumber drying operations

Treesearch

Omar A. Espinoza; Brian H. Bond; Philip Araman

2007-01-01

The Bolivian secondary forest products industry has experienced substantial growth during the last 10 years. Particularly, important investment has taken place in lumber drying capacity. Unfortunately, little information is available regarding lumber drying technology and practices used, which is essential for the formulation of improvement strategies. The Bolivian...

Bayesian framework for aerospace gas turbine engine prognostics

NASA Astrophysics Data System (ADS)

Zaidan, M. A.; Mills, A. R.; Harrison, R. F.

Prognostics is an emerging capability of modern health monitoring that aims to increase the fidelity of failure predictions. In the aerospace industry, it is a key technology to maximise aircraft availability, offering a route to increase time in-service and reduce operational disruption through improved asset management.

Prosthetic Hand For Holding Rods, Tools, And Handles

NASA Technical Reports Server (NTRS)

Belcher, Jewell G., Jr.; Vest, Thomas W.

1995-01-01

Prosthetic hand with quick-grip/quick-release lever broadens range of specialized functions available to lower-arm amputee by providing improved capabilities for gripping rods, tools, handles, and like. Includes two stationary lower fingers opposed by one pivoting upper finger. Lever operates in conjunction with attached bracket.

Improving the ability to review preoperative radiographs intraoperatively in trauma and orthopaedic theatres at Lancashire teaching hospitals

PubMed Central

Jump, Christopher

2017-01-01

Background The ability to review preoperative radiographs during trauma and orthopaedic surgery is essential for the surgeon to provide optimum treatment to the patient. However, due to current information technology (IT) systems, screen-savers frequently interrupt the ability to review images and theatre staff are not routinely available to deactivate the screen-saver. This prolongs theatre time for the patient and affects the quality of care provided. The aim of this quality improvement project was to improve the availability of radiographs for the surgeon to review intraoperatively. Method/results Data were collected from all trauma and orthopaedic theatres at two hospital sites covering all subspecialties and including emergency and elective cases. Baseline measurements showed that the frequency of preoperative radiographs not interrupted during an operation was 0% (0/50). Following this the Trust’s IT systems were improved to prevent activation of the screen-saver on the theatre computers using the generic theatre login details. After the first-cycle intervention, data were collected showing 52% (14/27) of preoperative radiographs were not interrupted by a screen-saver. The cause for this result being less than expected was investigated and found to be due to an alternative computer login being used on the theatre computers at one of the hospital sites. Education of theatre staff was then undertaken to ensure the correct theatre login was used and notices to remind staff placed on the theatre computers. After the second-cycle intervention, data were collected showing that 100% (26/26) of preoperative radiographs were not interrupted during operative time allowing the surgeon to review images when required. Conclusion/implications This quality improvement project has made changes to theatre IT systems and practices of theatre staff which has resulted in a significant improvement in the ability for the operating surgeon to review preoperative radiographs intraoperatively. PMID:29450269

Improving the ability to review preoperative radiographs intraoperatively in trauma and orthopaedic theatres at Lancashire teaching hospitals.

PubMed

Jump, Christopher

2017-01-01

The ability to review preoperative radiographs during trauma and orthopaedic surgery is essential for the surgeon to provide optimum treatment to the patient. However, due to current information technology (IT) systems, screen-savers frequently interrupt the ability to review images and theatre staff are not routinely available to deactivate the screen-saver. This prolongs theatre time for the patient and affects the quality of care provided. The aim of this quality improvement project was to improve the availability of radiographs for the surgeon to review intraoperatively. Data were collected from all trauma and orthopaedic theatres at two hospital sites covering all subspecialties and including emergency and elective cases. Baseline measurements showed that the frequency of preoperative radiographs not interrupted during an operation was 0% (0/50). Following this the Trust's IT systems were improved to prevent activation of the screen-saver on the theatre computers using the generic theatre login details. After the first-cycle intervention, data were collected showing 52% (14/27) of preoperative radiographs were not interrupted by a screen-saver. The cause for this result being less than expected was investigated and found to be due to an alternative computer login being used on the theatre computers at one of the hospital sites. Education of theatre staff was then undertaken to ensure the correct theatre login was used and notices to remind staff placed on the theatre computers. After the second-cycle intervention, data were collected showing that 100% (26/26) of preoperative radiographs were not interrupted during operative time allowing the surgeon to review images when required. This quality improvement project has made changes to theatre IT systems and practices of theatre staff which has resulted in a significant improvement in the ability for the operating surgeon to review preoperative radiographs intraoperatively.

Improving the pathologic evaluation of lung cancer resection specimens.

PubMed

Osarogiagbon, Raymond U; Hilsenbeck, Holly L; Sales, Elizabeth W; Berry, Allen; Jarrett, Robert W; Giampapa, Christopher S; Finch-Cruz, Clara N; Spencer, David

2015-08-01

Accurate post-operative prognostication and management heavily depend on pathologic nodal stage. Patients with nodal metastasis benefit from post-operative adjuvant chemotherapy, those with mediastinal nodal involvement may also benefit from adjuvant radiation therapy. However, the quality of pathologic nodal staging varies significantly, with major survival implications in large populations of patients. We describe the quality gap in pathologic nodal staging, and provide evidence of its potential reversibility by targeted corrective interventions. One intervention, designed to improve the surgical lymphadenectomy, specimen labeling, and secure transfer between the operating theatre and the pathology laboratory, involves use of pre-labeled specimen collection kits. Another intervention involves application of an improved method of gross dissection of lung resection specimens, to reduce the inadvertent loss of intrapulmonary lymph nodes to histologic examination for metastasis. These corrective interventions are the subject of a regional dissemination and implementation project in diverse healthcare systems in a tri-state region of the United States with some of the highest lung cancer incidence and mortality rates. We discuss the potential of these interventions to significantly improve the accuracy of pathologic nodal staging, risk stratification, and the quality of specimens available for development of stage-independent prognostic markers in lung cancer.

Analysis of Availability of Longwall-Shearer Based On Its Working Cycle

NASA Astrophysics Data System (ADS)

Brodny, Jaroslaw; Tutak, Magdalena

2017-12-01

Effective use of any type of devices, particularly machines has very significant meaning for mining enterprises. High costs of their purchase and tenancy cause that these enterprises tend to the best use of own technical potential. However, characteristics of mining production causes that this process not always proceeds without interferences. Practical experiences show that determination of objective measure of utilization of machine in mining company is not simple. In the paper methodology allowing to solve this problem is presented. Longwall-shearer, as the most important machine between longwall mechanical complex. Also it was assumed that the most significant meaning for determination of effectiveness of longwall-shearer has its availability, i.e. its effective time of work related to standard time. Such an approach is conforming to OEE model. However, specification of mining branch causes that determined availability do not give actual state of longwall-shearer’s operation. Therefore, this availability was related to the operation cycle of longwall-shearer. In presented example a longwall-shearer works in unidirectional cycle of mining. It causes that in one direction longwall-shearer mines, moving with operating velocity, and in other direction it does not mine and moves with manoeuvre velocity. Such defined working cycle became a base for determinate availability of longwall-shearer. Using indications of industrial automatic system for each of working shift there were determined number of cycles of longwall-shearer and availability of each one. Accepted of such way of determination of availability of longwall-shearer enabled to perform accurate analysis of losses of its availability. These losses result from non-planned shutdowns of longwall-shearer. Thanks to performed analysis based on the operating cycle of longwall-shearer time of its standstill for particular phase of cycle were determined. Presented methodology of determination of longwall-shearer’s availability enables to obtain information which may be used for optimization of mining process. Knowledge of particular phases of longwall-shearer’s operation, in which reduced availability occurs, allows to direct the repairing actions exactly to these regions. Developed methodology and obtained results create great opportunities for practical application and improvement of effectiveness of underground exploitation.

Improving a workstation in an existing cab by means of a participatory approach: the case of subway operators' workstations.

PubMed

Bellemare, Marie; Beaugrand, Sylvie; Larue, Christian; Champoux, Danièle

2009-01-01

A study was conducted to identify possible solutions for redesigning a subway cab in order to improve the posture of drivers working in a restricted space. The approach used included the participation of a working group comprised of operations, maintenance, and engineering managers as well as several drivers. After 6 meetings in which different simulation techniques were used, the working group proposed changes for increasing the available space inside the cab and three seat designs. The involvement of the actors from the three departments affected by the changes, as well as the operators, throughout the process, was a determining factor in the advancement and acceptance of the projects. The fact that 400 cars are currently in service and must be modified means that it will take several years to implement the modifications in the entire fleet.

AIRS associated accomplishments at the JCSDA: First use of full spatial resolution hyperspectral data show significant improvements in global forecasts

NASA Astrophysics Data System (ADS)

Le Marshall, J.; Jung, J.; Lord, S. J.; Derber, J. C.; Treadon, R.; Joiner, J.; Goldberg, M.; Wolf, W.; Liu, H. C.

2005-08-01

The National Aeronautics and Space Administration (NASA), National Oceanic and Atmospheric Administration (NOAA), and Department of Defense (DoD), Joint Center for Satellite Data Assimilation (JCSDA) was established in 2000/2001. The goal of the JCSDA is to accelerate the use of observations from earth-orbiting satellites into operational numerical environmental analysis and prediction systems for the purpose of improving weather and oceanic forecasts, seasonal climate forecasts and the accuracy of climate data sets. As a result, a series of data assimilation experiments were undertaken at the JCSDA as part of the preparations for the operational assimilation of AIRS data by its partner organizations1,2. Here, for the first time full spatial resolution radiance data, available in real-time from the AIRS instrument, were used at the JCSDA in data assimilation studies over the globe utilizing the operational NCEP Global Forecast System (GFS). The radiance data from each channel of the instrument were carefully screened for cloud effects and those radiances which were deemed to be clear of cloud effects were used by the GFS forecast system. The result of these assimilation trials has been a first demonstration of significant improvements in forecast skill over both the Northern and Southern Hemisphere compared to the operational system without AIRS data. The experimental system was designed in a way that rendered it feasible for operational application, and that constraint involved using the subset of AIRS channels chosen for operational distribution and an analysis methodology close to the current analysis practice, with particular consideration given to time limitations. As a result, operational application of these AIRS data was enabled by the recent NCEP operational upgrade. In addition, because of the improved impact resulting from use of this enhanced data set compared to that used operationally to date, provision of a realtime "warmest field" of view data set has been established for use by international NWP Centers.

Clinical operations management in radiology.

PubMed

Ondategui-Parra, Silvia; Gill, Ileana E; Bhagwat, Jui G; Intrieri, Lisa A; Gogate, Adheet; Zou, Kelly H; Nathanson, Eric; Seltzer, Steven E; Ros, Pablo R

2004-09-01

Providing radiology services is a complex and technically demanding enterprise in which the application of operations management (OM) tools can play a substantial role in process management and improvement. This paper considers the benefits of an OM process in a radiology setting. Available techniques and concepts of OM are addressed, along with gains and benefits that can be derived from these processes. A reference framework for the radiology processes is described, distinguishing two phases in the initial assessment of a unit: the diagnostic phase and the redesign phase.

Evaluation of Winter Operational Runway Friction Measurement Equipment, Procedures, and Research

NASA Technical Reports Server (NTRS)

1995-01-01

This document produced by the FAA/Industry Winter Runway Friction Measurement and Reporting Working Group, is designed to provide an overview of current information on the present guidance, practices, and procedures for reporting runway pavement surface conditions during winter operations at airports. It contains recommendations on the desirability of providing the best procedural consistency and standardization and discusses the available means to implement the guidance that will result in improved aviation safety at airports during hazardous winter conditions.

Quantifying the Economic and Grid Reliability Impacts of Improved Wind Power Forecasting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Qin; Martinez-Anido, Carlo Brancucci; Wu, Hongyu

Wind power forecasting is an important tool in power system operations to address variability and uncertainty. Accurately doing so is important to reducing the occurrence and length of curtailment, enhancing market efficiency, and improving the operational reliability of the bulk power system. This research quantifies the value of wind power forecasting improvements in the IEEE 118-bus test system as modified to emulate the generation mixes of Midcontinent, California, and New England independent system operator balancing authority areas. To measure the economic value, a commercially available production cost modeling tool was used to simulate the multi-timescale unit commitment (UC) and economicmore » dispatch process for calculating the cost savings and curtailment reductions. To measure the reliability improvements, an in-house tool, FESTIV, was used to calculate the system's area control error and the North American Electric Reliability Corporation Control Performance Standard 2. The approach allowed scientific reproducibility of results and cross-validation of the tools. A total of 270 scenarios were evaluated to accommodate the variation of three factors: generation mix, wind penetration level, and wind fore-casting improvements. The modified IEEE 118-bus systems utilized 1 year of data at multiple timescales, including the day-ahead UC, 4-hour-ahead UC, and 5-min real-time dispatch. The value of improved wind power forecasting was found to be strongly tied to the conventional generation mix, existence of energy storage devices, and the penetration level of wind energy. The simulation results demonstrate that wind power forecasting brings clear benefits to power system operations.« less

STS payload data collection and accommodations analysis study. Volume 3: Accommodations analysis

NASA Technical Reports Server (NTRS)

1978-01-01

Payload requirements were compared to launch site accommodations and flight accommodations for a number of Spacelab payloads. Experiment computer operating system accommodations were also considered. A summary of accommodations in terms of resources available for payload discretionary use and recommendations for Spacelab/STS accommodation improvements are presented.

An Interactive Model for Studying Student Retention. AIR 1990 Annual Forum Paper.

ERIC Educational Resources Information Center

Glover, Robert H.; Wilcox, Jerry

A design for improving the quality of information available for continuous operational study of student retention at the University of Hartford in Connecticut was examined involving a microcomputer based decision support system for student retention research. The system, an interactive modeling approach to conduct longitudinal and comparative…

Special Operations Forces Aviation on a Shoestring Budget: An Effectiveness Analysis of Light and Medium Fixed Wing Aircraft

DTIC Science & Technology

2012-12-01

C2 Command and Control CAIG Cost Analysis Improvement Group CAS Close Air Support CASA Construcciones Aeronáuticas SA CLS Contract...Commercially Available Off-the-Shelf Commercially available off-the shelf (COTS) is defined as any item of supply (including construction material...uses are found for old weapons that were constructed for use in industrial war against soldiers and heavy armament. 6. The sides are mostly non

Application of advanced technologies to small, short-haul transport aircraft

NASA Technical Reports Server (NTRS)

Coussens, T. G.; Tullis, R. H.

1980-01-01

The performance and economic benefits available by incorporation of advanced technologies into the small, short haul air transport were assessed. Low cost structure and advanced composite material, advanced turboprop engines and new propellers, advanced high lift systems and active controls; and alternate aircraft configurations with aft mounted engines were investigated. Improvements in fuel consumed and aircraft economics (acquisition cost and direct operating cost) are available by incorporating selected advanced technologies into the small, short haul aircraft.

A Reserve-based Method for Mitigating the Impact of Renewable Energy

NASA Astrophysics Data System (ADS)

Krad, Ibrahim

The fundamental operating paradigm of today's power systems is undergoing a significant shift. This is partially motivated by the increased desire for incorporating variable renewable energy resources into generation portfolios. While these generating technologies offer clean energy at zero marginal cost, i.e. no fuel costs, they also offer unique operating challenges for system operators. Perhaps the biggest operating challenge these resources introduce is accommodating their intermittent fuel source availability. For this reason, these generators increase the system-wide variability and uncertainty. As a result, system operators are revisiting traditional operating strategies to more efficiently incorporate these generation resources to maximize the benefit they provide while minimizing the challenges they introduce. One way system operators have accounted for system variability and uncertainty is through the use of operating reserves. Operating reserves can be simplified as excess capacity kept online during real time operations to help accommodate unforeseen fluctuations in demand. With new generation resources, a new class of operating reserves has emerged that is generally known as flexibility, or ramping, reserves. This new reserve class is meant to better position systems to mitigate severe ramping in the net load profile. The best way to define this new requirement is still under investigation. Typical requirement definitions focus on the additional uncertainty introduced by variable generation and there is room for improvement regarding explicit consideration for the variability they introduce. An exogenous reserve modification method is introduced in this report that can improve system reliability with minimal impacts on total system wide production costs. Another potential solution to this problem is to formulate the problem as a stochastic programming problem. The unit commitment and economic dispatch problems are typically formulated as deterministic problems due to fast solution times and the solutions being sufficient for operations. Improvements in technical computing hardware have reignited interest in stochastic modeling. The variability of wind and solar naturally lends itself to stochastic modeling. The use of explicit reserve requirements in stochastic models is an area of interest for power system researchers. This report introduces a new reserve modification implementation based on previous results to be used in a stochastic modeling framework. With technological improvements in distributed generation technologies, microgrids are currently being researched and implemented. Microgrids are small power systems that have the ability to serve their demand with their own generation resources and may have a connection to a larger power system. As battery technologies improve, they are becoming a more viable option in these distributed power systems and research is necessary to determine the most efficient way to utilize them. This report will investigate several unique operating strategies for batteries in small power systems and analyze their benefits. These new operating strategies will help reduce operating costs and improve system reliability.

Fully-Integrated Simulation of Conjunctive Use from Field to Basin Scales: Development of a Surface Water Operations Module for MODFLOW-OWHM

NASA Astrophysics Data System (ADS)

Ferguson, I. M.; Boyce, S. E.; Hanson, R. T.; Llewellyn, D.

2014-12-01

It is well established that groundwater pumping affects surface-water availability by intercepting groundwater that would otherwise discharge to streams and/or by increasing seepage from surface-water channels. Conversely, surface-water management operations effect groundwater availability by altering the timing, location, and quantity of groundwater recharge and demand. Successful conjunctive use may require analysis with an integrated approach that accounts for the many interactions and feedbacks between surface-water and groundwater availability and their joint management. In order to improve simulation and analysis of conjunctive use, Bureau of Reclamation and USGS are collaborating to develop a surface-water operations module within MODFLOW One Water Hydrologic Flow Model (MF-OWHM), a new version of the USGS Modular Groundwater Flow Model (MODFLOW). Here we describe the development and application of the surface-water operations module. We provide an overview of the conceptual approach used to simulate surface-water operations—including surface-water storage, allocation, release, diversion, and delivery on monthly to seasonal time frames—in a fully-integrated manner. We then present results from a recent case study analysis of the Rio Grande Project, a large-scale irrigation project located in New Mexico and Texas, under varying surface-water operations criteria and climate conditions. Case study results demonstrate the importance of integrated hydrologic simulation of surface water and groundwater operations in analysis and management of conjunctive-use systems.

MOLAR: Modular Linux and Adaptive Runtime Support for HEC OS/R Research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frank Mueller

2009-02-05

MOLAR is a multi-institution research effort that concentrates on adaptive, reliable,and efficient operating and runtime system solutions for ultra-scale high-end scientific computing on the next generation of supercomputers. This research addresses the challenges outlined by the FAST-OS - forum to address scalable technology for runtime and operating systems --- and HECRTF --- high-end computing revitalization task force --- activities by providing a modular Linux and adaptable runtime support for high-end computing operating and runtime systems. The MOLAR research has the following goals to address these issues. (1) Create a modular and configurable Linux system that allows customized changes based onmore » the requirements of the applications, runtime systems, and cluster management software. (2) Build runtime systems that leverage the OS modularity and configurability to improve efficiency, reliability, scalability, ease-of-use, and provide support to legacy and promising programming models. (3) Advance computer reliability, availability and serviceability (RAS) management systems to work cooperatively with the OS/R to identify and preemptively resolve system issues. (4) Explore the use of advanced monitoring and adaptation to improve application performance and predictability of system interruptions. The overall goal of the research conducted at NCSU is to develop scalable algorithms for high-availability without single points of failure and without single points of control.« less

Automated Identification of Initial Storm Electrification and End-of-Storm Electrification Using Electric Field Mill Sensors

NASA Technical Reports Server (NTRS)

Maier, Launa M.; Huddleston, Lisa L.

2017-01-01

Kennedy Space Center (KSC) operations are located in a region which experiences one of the highest lightning densities across the United States. As a result, on average, KSC loses almost 30 minutes of operational availability each day for lightning sensitive activities. KSC is investigating using existing instrumentation and automated algorithms to improve the timeliness and accuracy of lightning warnings. Additionally, the automation routines will be warning on a grid to minimize under-warnings associated with not being located in the center of the warning area and over-warnings associated with encompassing too large an area. This study discusses utilization of electric field mill data to provide improved warning times. Specifically, this paper will demonstrate improved performance of an enveloping algorithm of the electric field mill data as compared with the electric field zero crossing to identify initial storm electrification. End-of-Storm-Oscillation (EOSO) identification algorithms will also be analyzed to identify performance improvement, if any, when compared with 30 minutes after the last lightning flash.

An intelligent position-specific training system for mission operations

NASA Technical Reports Server (NTRS)

Schneider, M. P.

1992-01-01

Marshall Space Flight Center's (MSFC's) payload ground controller training program provides very good generic training; however, ground controller position-specific training can be improved by including position-specific training systems in the training program. This report explains why MSFC needs to improve payload ground controller position-specific training. The report describes a generic syllabus for position-specific training systems, a range of system designs for position-specific training systems, and a generic development process for developing position-specific training systems. The report also describes a position-specific training system prototype that was developed for the crew interface coordinator payload operations control center ground controller position. The report concludes that MSFC can improve the payload ground controller training program by incorporating position-specific training systems for each ground controller position; however, MSFC should not develop position-specific training systems unless payload ground controller position experts will be available to participate in the development process.

Damage-mitigating control of space propulsion systems for high performance and extended life

NASA Technical Reports Server (NTRS)

Ray, Asok; Wu, Min-Kuang; Dai, Xiaowen; Carpino, Marc; Lorenzo, Carl F.

1993-01-01

Calculations are presented showing that a substantial improvement in service life of a reusable rocket engine can be achieved by an insignificant reduction in the system dynamic performance. The paper introduces the concept of damage mitigation and formulates a continuous-time model of fatigue damage dynamics. For control of complex mechanical systems, damage prediction and damage mitigation are carried out based on the available sensory and operational information such that the plant can be inexpensively maintained and safely and efficiently steered under diverse operating conditions. The results of simulation experiments are presented for transient operations of a reusable rocket engine.

Analysis of RHIC beam dump pre-fires

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, W.; Ahrens, L.; Fischer, W.

2011-03-28

It has been speculated that the beam may cause instability of the RHIC Beam Abort Kickers. In this study, we explore the available data of past beam operations, the device history of key modulator components, and the radiation patterns to examine the correlations. The RHIC beam abort kicker system was designed and built in the 90's. Over last decade, we have made many improvements to bring the RHIC beam abort kicker system to a stable operational state. However, the challenge continues. We present the analysis of the pre-fire, an unrequested discharge of kicker, issues which relates to the RHIC machinemore » safety and operational stability.« less

Elbow ulnar collateral ligament injuries in athletes: Can we improve our outcomes?

PubMed Central

Redler, Lauren H; Degen, Ryan M; McDonald, Lucas S; Altchek, David W; Dines, Joshua S

2016-01-01

Injury to the ulnar collateral ligament (UCL) most commonly occurs in the overhead throwing athlete. Knowledge surrounding UCL injury pathomechanics continues to improve, leading to better preventative treatment strategies and rehabilitation programs. Conservative treatment strategies for partial injuries, improved operative techniques for reconstruction in complete tears, adjunctive treatments, as well as structured sport specific rehabilitation programs including resistive exercises for the entire upper extremity kinetic chain are all important factors in allowing for a return to throwing in competitive environments. In this review, we explore each of these factors and provide recommendations based on the available literature to improve outcomes in UCL injuries in athletes. PMID:27114930

Improved control strategy for wind-powered refrigerated storage of apples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baldwin, J.D.C.; Vaughan, D.H.

1981-01-01

A refrigerated apple storage facility was constructed at the VPI and SU Horticultural Research Farm in Blacksburg, Virginia and began operation in March 1978. The system included a 10-kW electric wind generator, electrical battery storage, thermal (ice) storage, and auxiliary power. The need for an improved control system for the VPI and SU system was determined from tests on the individual components and in situ performance tests. The results of these tests formed the basis for an improved control strategy to improve the utilization of available wind energy and reduce the need for auxiliary power while maintaining an adequate applemore » storage environment.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paul Jehn; Mike Stettner

GWPC, DOGGR, and other state agencies propose to build eBusiness applications based on a .NET front-end user interface for the DOE's Energy 100 Award-winning Risk Based Data Management System (RBDMS) data source and XML Web services. This project will slash the costs of regulatory compliance by automating routine regulatory reporting and permit notice review and by making it easier to exchange data with the oil and gas industry--especially small, independent operators. Such operators, who often do not have sophisticated in-house databases, will be able to use a subset of the same RBDMS tools available to the agencies on the desktopmore » to file permit notices and production reports online. Once the data passes automated quality control checks, the application will upload the data into the agency's RBDMS data source. The operators also will have access to state agency datasets to focus exploration efforts and to perform production forecasting, economic evaluations, and risk assessments. With the ability to identify economically feasible oil and gas prospects, including unconventional plays, over the Internet, operators will minimize travel and other costs. Because GWPC will coordinate these data sharing efforts with the Bureau of Land Management (BLM), this project will improve access to public lands and make strides towards reducing the duplicative reporting to which industry is now subject for leases that cross jurisdictions. The resulting regulatory streamlining and improved access to agency data will make more domestic oil and gas available to the American public while continuing to safeguard environmental assets.« less

Promoting patient safety through prospective risk identification: example from peri-operative care.

PubMed

Smith, A; Boult, M; Woods, I; Johnson, S

2010-02-01

Investigation of patient safety incidents has focused on retrospective analyses once incidents have occurred. Prospective risk analysis techniques complement this but have not been widely used in healthcare. Prospective risk identification of non-operative risks associated with adult elective surgery under general anaesthesia using a customised structured "what if" checklist and development of risk matrix. Prioritisation of recommendations arising by cost, ease and likely speed of implementation. Groups totalling 20 clinical and administrative healthcare staff involved in peri-operative care and risk experts convened by the UK National Patient Safety Agency. 102 risks were identified and 95 recommendations made. The top 20 recommendations together were judged to encompass about 75% of the total estimated risk attributable to the processes considered. Staffing and organisational issues (21% of total estimated risk) included recommendations for removing distractions from the operating theatre, ensuring the availability of senior anaesthetists and promoting standards and flexible working among theatre staff. Devices and equipment (19% of total estimated risk) could be improved by training and standardisation; airway control and temperature monitoring were identified as two specific areas. Pre-assessment of patients before admission to hospital (12% of estimated risk) could be improved by defining a data set for adequate pre-assessment and making this available throughout the NHS. This technique can be successfully applied by healthcare staff but expert facilitation of groups is advisable. Such wider-ranging processes can potentially lead to more comprehensive risk reduction than "single-issue" risk alerts.

Method for Prediction of the Power Output from Photovoltaic Power Plant under Actual Operating Conditions

NASA Astrophysics Data System (ADS)

Obukhov, S. G.; Plotnikov, I. A.; Surzhikova, O. A.; Savkin, K. D.

2017-04-01

Solar photovoltaic technology is one of the most rapidly growing renewable sources of electricity that has practical application in various fields of human activity due to its high availability, huge potential and environmental compatibility. The original simulation model of the photovoltaic power plant has been developed to simulate and investigate the plant operating modes under actual operating conditions. The proposed model considers the impact of the external climatic factors on the solar panel energy characteristics that improves accuracy in the power output prediction. The data obtained through the photovoltaic power plant operation simulation enable a well-reasoned choice of the required capacity for storage devices and determination of the rational algorithms to control the energy complex.

Optimizing process and equipment efficiency using integrated methods

NASA Astrophysics Data System (ADS)

D'Elia, Michael J.; Alfonso, Ted F.

1996-09-01

The semiconductor manufacturing industry is continually riding the edge of technology as it tries to push toward higher design limits. Mature fabs must cut operating costs while increasing productivity to remain profitable and cannot justify large capital expenditures to improve productivity. Thus, they must push current tool production capabilities to cut manufacturing costs and remain viable. Working to continuously improve mature production methods requires innovation. Furthermore, testing and successful implementation of these ideas into modern production environments require both supporting technical data and commitment from those working with the process daily. At AMD, natural work groups (NWGs) composed of operators, technicians, engineers, and supervisors collaborate to foster innovative thinking and secure commitment. Recently, an AMD NWG improved equipment cycle time on the Genus tungsten silicide (WSi) deposition system. The team used total productive manufacturing (TPM) to identify areas for process improvement. Improved in-line equipment monitoring was achieved by constructing a real time overall equipment effectiveness (OEE) calculator which tracked equipment down, idle, qualification, and production times. In-line monitoring results indicated that qualification time associated with slow Inspex turn-around time and machine downtime associated with manual cleans contributed greatly to reduced availability. Qualification time was reduced by 75% by implementing a new Inspex monitor pre-staging technique. Downtime associated with manual cleans was reduced by implementing an in-situ plasma etch back to extend the time between manual cleans. A designed experiment was used to optimize the process. Time between 18 hour manual cleans has been improved from every 250 to every 1500 cycles. Moreover defect density realized a 3X improvement. Overall, the team achieved a 35% increase in tool availability. This paper details the above strategies and accomplishments.

Optimizing operational water management with soil moisture data from Sentinel-1 satellites

NASA Astrophysics Data System (ADS)

Pezij, Michiel; Augustijn, Denie; Hendriks, Dimmie; Hulscher, Suzanne

2016-04-01

In the Netherlands, regional water authorities are responsible for management and maintenance of regional water bodies. Due to socio-economic developments (e.g. agricultural intensification and on-going urbanisation) and an increase in climate variability, the pressure on these water bodies is growing. Optimization of water availability by taking into account the needs of different users, both in wet and dry periods, is crucial for sustainable developments. To support timely and well-directed operational water management, accurate information on the current state of the system as well as reliable models to evaluate water management optimization measures are essential. Previous studies showed that the use of remote sensing data (for example soil moisture data) in water management offers many opportunities (e.g. Wanders et al. (2014)). However, these data are not yet used in operational applications at a large scale. The Sentinel-1 satellites programme offers high spatiotemporal resolution soil moisture data (1 image per 6 days with a spatial resolution of 10 by 10 m) that are freely available. In this study, these data will be used to improve the Netherlands Hydrological Instrument (NHI). The NHI consists of coupled models for the unsaturated zone (MetaSWAP), groundwater (iMODFLOW) and surface water (Mozart and DM). The NHI is used for scenario analyses and operational water management in the Netherlands (De Lange et al., 2014). Due to the lack of soil moisture data, the unsaturated zone model is not yet thoroughly validated and its output is not used by regional water authorities for decision-making. Therefore, the newly acquired remotely sensed soil moisture data will be used to improve the skill of the MetaSWAP-model and the NHI as whole. The research will focus among other things on the calibration of soil parameters by comparing model output (MetaSWAP) with the remotely sensed soil moisture data. Eventually, we want to apply data-assimilation to improve operational water management in cooperation with users. As a first step, the current simulation of soil moisture processes within the NHI will be reviewed. We want to present the findings of this assessment as well as the research methodology. This PhD-research is part of the Optimizing Water Availability with Sentinel-1 Satellites (OWAS1S)-project in which two other PhD-students are participating. They are focussing on the translation of raw Sentinel-1 satellite data to surface soil moisture data and the application of the remotely sensed soil moisture data on crop water availability and trafficability on field scale. References: De Lange, W. J., Prinsen, G. F., Hoogewoud, J. C., Veldhuizen, A. A., Verkaik, J., Oude Essink, G. H. P., van Walsum, P. E. V., Delsman, J. R., Hunink, J. C., Massop, H. T. L., & Kroon, T. (2014). An operational, multi-scale, multi-model system for consensus-based, integrated water management and policy analysis: The Netherlands Hydrological Instrument. Environmental Modelling & Software, 59, 98-108. doi: 10.1016/j.envsoft.2014.05.009 Wanders, N., Karssenberg, D., de Roo, A., de Jong, S. M., & Bierkens, M. F. P. (2014). The suitability of remotely sensed soil moisture for improving operational flood forecasting. Hydrology and Earth System Sciences, 18(6), 2343-2357. doi: 10.5194/hess-18-2343-2014

Improving Water Resources System Operation by Direct Use of Hydroclimatic Information

NASA Astrophysics Data System (ADS)

Castelletti, A.; Pianosi, F.

2011-12-01

It is generally agreed that more information translates into better decisions. For instance, the availability of inflow predictions can improve reservoir operation; soil moisture data can be exploited to increase irrigation efficiency; etc. However, beyond this general statement, many theoretical and practical questions remain open. Provided that not all information sources are equally relevant, how does their value depend on the physical features of the water system and on the purposes of the system operation? What is the minimum lead time needed for anticipatory management to be effective? How does uncertainty in the information propagates through the modelling chain from hydroclimatic data through descriptive and decision models, and finally affect the decision? Is the data-predictions-decision paradigm truly effective or would it be better to directly use hydroclimatic data to take optimal decisions, skipping the intermediate step of hydrological forecasting? In this work we investigate these issues by application to the management of a complex water system in Northern Vietnam, characterized by multiple, conflicting objectives including hydropower production, flood control and water supply. First, we quantify the value of hydroclimatic information as the improvement in the system performances that could be attained under the (ideal) assumption of perfect knowledge of all future meteorological and hydrological input. Then, we assess and compare the relevance of different candidate information (meteorological or hydrological observations; ground or remote data; etc.) for the purpose of system operation by novel Input Variable Selection techniques. Finally, we evaluate the performance improvement made possible by the use of such information in re-designing the system operation.

Standardization of reflectance measurements in dispersed organic matter: results of an exercise to improve interlaboratory agreement

USGS Publications Warehouse

Hackley, Paul C.; Araujo, Carla Viviane; Borrego, Angeles G.; Bouzinos, Antonis; Cardott, Brian; Cook, Alan C.; Eble, Cortland; Flores, Deolinda; Gentzis, Thomas; Gonçalves, Paula Alexandra; Filho, João Graciano Mendonça; Hámor-Vidó, Mária; Jelonek, Iwona; Kommeren, Kees; Knowles, Wayne; Kus, Jolanta; Mastalerz, Maria; Menezes, Taíssa Rêgo; Newman, Jane; Pawlewicz, Mark; Pickel, Walter; Potter, Judith; Ranasinghe, Paddy; Read, Harold; Reyes, Julito; Rodriguez, Genaro De La Rosa; de Souza, Igor Viegas Alves Fernandes; Suarez-Ruiz, Isabel; Sýkorová, Ivana; Valentine, Brett J.

2015-01-01

Vitrinite reflectance generally is considered the most robust thermal maturity parameter available for application to hydrocarbon exploration and petroleum system evaluation. However, until 2011 there was no standardized methodology available to provide guidelines for vitrinite reflectance measurements in shale. Efforts to correct this deficiency resulted in publication of ASTM D7708: Standard test method for microscopical determination of the reflectance of vitrinite dispersed in sedimentary rocks. In 2012-2013, an interlaboratory exercise was conducted to establish precision limits for the D7708 measurement technique. Six samples, representing a wide variety of shale, were tested in duplicate by 28 analysts in 22 laboratories from 14 countries. Samples ranged from immature to overmature (0.31-1.53% Ro), from organic-lean to organic-rich (1-22 wt.% total organic carbon), and contained Type I (lacustrine), Type II (marine), and Type III (terrestrial) kerogens. Repeatability limits (maximum difference between valid repetitive results from same operator, same conditions) ranged from 0.03-0.11% absolute reflectance, whereas reproducibility limits (maximum difference between valid results obtained on same test material by different operators, different laboratories) ranged from 0.12-0.54% absolute reflectance. Repeatability and reproducibility limits degraded consistently with increasing maturity and decreasing organic content. However, samples with terrestrial kerogens (Type III) fell off this trend, showing improved levels of reproducibility due to higher vitrinite content and improved ease of identification. Operators did not consistently meet the reporting requirements of the test method, indicating that a common reporting template is required to improve data quality. The most difficult problem encountered was the petrographic distinction of solid bitumens and low-reflecting inert macerals from vitrinite when vitrinite occurred with reflectance ranges overlapping the other components. Discussion among participants suggested this problem could not be easily corrected via kerogen concentration or solvent extraction and is related to operator training and background. No statistical difference in mean reflectance was identified between participants reporting bitumen reflectance vs. vitrinite reflectance vs. a mixture of bitumen and vitrinite reflectance values, suggesting empirical conversion schemes should be treated with caution. Analysis of reproducibility limits obtained during this exercise in comparison to reproducibility limits from historical interlaboratory exercises suggests use of a common methodology (D7708) improves interlaboratory precision. Future work will investigate opportunities to improve reproducibility in high maturity, organic-lean shale varieties.

Decreasing delays in urgent and expedited surgery in a university teaching hospital through audit and communication between peri-operative and surgical directorates.

PubMed

Cosgrove, J F; Gaughan, M; Snowden, C P; Lees, T

2008-06-01

National Confidential Enquiry into Patient Outcome and Death guidelines for urgent surgery recommend a fully staffed emergency operating theatre and restriction of 'after-midnight' operating to immediate life-, limb- or organ-threatening conditions. Audit performed in our institution demonstrated significant decreases in waiting times for urgent surgery and an increased seniority of medical care associated with overnight pre-operative assessment of patients by anaesthetic trainees. Nevertheless, urgent cases continued to be delayed unnecessarily. A classification of delays was developed from existing guidelines and their incidence was audited. The results were disseminated to involved directorates. A repeat of the audit demonstrated a significant decrease in delays (p = 0.001), a significant increase in the availability of surgeons (p = 0.001) and a significant decrease in the median waiting time for urgent surgery compared to the first audit cycle and a previous standard (p < 0.01). We conclude that auditing delays and disseminating the results of the audit significantly decreases delays and median waiting times for urgent surgery because of improved surgical availability.

Wisconsin System for Instructional Management: Terminal Operator Manual. Practical Paper No. 19.

ERIC Educational Resources Information Center

Bozeman, William C.; And Others

The Wisconsin System for Instructional Management (WIS-SIM) is a computer managed instruction (CMI) system designed to improve instructional decision making in order to maximize the educational progress of each child while making efficient use of the available human, material, and financial resources within an organizational structure such as the…

Is it time to revisit the log-sort yard?

Treesearch

John Dramm; Gerry Jackson

2000-01-01

Log-sort yards provide better utilization and marketing with improved value recovery of currently available timber resources in North America. Log-sort yards provide many services in marketing wood and fiber by concentrating, merchandising, manufacturing, sorting, and adding value to logs. Such operations supply forest products firms with desired raw materials, which...

Improving the U.S. Military’s Response to Homeland Humanitarian Assistance Operations

DTIC Science & Technology

2006-05-16

Wilma: A Video -Conference Coup Mr. Fugate Seizes 300 Phones”, Wall Street Journal, 8 December 2005, A1. 30 Ibid. 15 Katrina while 5th Army was...crisis. 37 Lolita C. Baldor, “Military Shores up Hurricane Response”, Los Angeles Times, 6 May 2006, available from http

Improving Project Management of Complex or Major Systems

DTIC Science & Technology

2016-05-05

funding available through vehicle Mod-lines --- shared across various motor transport programs PB-17 $M (including OCO) Program ACAT FYDP (FY17...Requirements Description (CARD) ▪ ▪ ▪ ▪ ▪ ▪ DOT&E REPORT ON INITIAL OPERATIONAL TEST AND EVALUATION ( IOT &E) ▪ Development RFP Release Cost Assessment

Aviation and climate change : aircraft emissions expected to grow, but technological and operational improvements and government policies can help control emissions

DOT National Transportation Integrated Search

2009-06-01

A number of policy options to address aircraft emissions are available to governments and can be part of broader policies to address emissions from many sources including aircraft. Market-based measures can establish a price for emissions and provide...

Reliability culture at La Silla Paranal Observatory

NASA Astrophysics Data System (ADS)

Gonzalez, Sergio

2010-07-01

The Maintenance Department at the La Silla - Paranal Observatory has been an important base to keep the operations of the observatory at a good level of reliability and availability. Several strategies have been implemented and improved in order to cover these requirements and keep the system and equipment working properly when it is required. For that reason, one of the latest improvements has been the introduction of the concept of reliability, which implies that we don't simply speak about reliability concepts. It involves much more than that. It involves the use of technologies, data collecting, data analysis, decision making, committees concentrated in analysis of failure modes and how they can be eliminated, aligning the results with the requirements of our internal partners and establishing steps to achieve success. Some of these steps have already been implemented: data collection, use of technologies, analysis of data, development of priority tools, committees dedicated to analyze data and people dedicated to reliability analysis. This has permitted us to optimize our process, analyze where we can improve, avoid functional failures, reduce the failures range in several systems and subsystems; all this has had a positive impact in terms of results for our Observatory. All these tools are part of the reliability culture that allows our system to operate with a high level of reliability and availability.

The costs of uncoordinated infrastructure management in multi-reservoir river basins

NASA Astrophysics Data System (ADS)

Jeuland, Marc; Baker, Justin; Bartlett, Ryan; Lacombe, Guillaume

2014-10-01

Though there are surprisingly few estimates of the economic benefits of coordinated infrastructure development and operations in international river basins, there is a widespread belief that improved cooperation is beneficial for managing water scarcity and variability. Hydro-economic optimization models are commonly-used for identifying efficient allocation of water across time and space, but such models typically assume full coordination. In the real world, investment and operational decisions for specific projects are often made without full consideration of potential downstream impacts. This paper describes a tractable methodology for evaluating the economic benefits of infrastructure coordination. We demonstrate its application over a range of water availability scenarios in a catchment of the Mekong located in Lao PDR, the Nam Ngum River Basin. Results from this basin suggest that coordination improves system net benefits from irrigation and hydropower by approximately 3-12% (or US12-53 million/yr) assuming moderate levels of flood control, and that the magnitude of coordination benefits generally increases with the level of water availability and with inflow variability. Similar analyses would be useful for developing a systematic understanding of the factors that increase the costs of non-cooperation in river basin systems worldwide, and would likely help to improve targeting of efforts to stimulate complicated negotiations over water resources.

Mapping multiple components of malaria risk for improved targeting of elimination interventions.

PubMed

Cohen, Justin M; Le Menach, Arnaud; Pothin, Emilie; Eisele, Thomas P; Gething, Peter W; Eckhoff, Philip A; Moonen, Bruno; Schapira, Allan; Smith, David L

2017-11-13

There is a long history of considering the constituent components of malaria risk and the malaria transmission cycle via the use of mathematical models, yet strategic planning in endemic countries tends not to take full advantage of available disease intelligence to tailor interventions. National malaria programmes typically make operational decisions about where to implement vector control and surveillance activities based upon simple categorizations of annual parasite incidence. With technological advances, an enormous opportunity exists to better target specific malaria interventions to the places where they will have greatest impact by mapping and evaluating metrics related to a variety of risk components, each of which describes a different facet of the transmission cycle. Here, these components and their implications for operational decision-making are reviewed. For each component, related mappable malaria metrics are also described which may be measured and evaluated by malaria programmes seeking to better understand the determinants of malaria risk. Implementing tailored programmes based on knowledge of the heterogeneous distribution of the drivers of malaria transmission rather than only consideration of traditional metrics such as case incidence has the potential to result in substantial improvements in decision-making. As programmes improve their ability to prioritize their available tools to the places where evidence suggests they will be most effective, elimination aspirations may become increasingly feasible.

Improvement in operational characteristics of KEPCO’s line-commutation-type superconducting hybrid fault current limiter

NASA Astrophysics Data System (ADS)

Yim, S.-W.; Park, B.-C.; Jeong, Y.-T.; Kim, Y.-J.; Yang, S.-E.; Kim, W.-S.; Kim, H.-R.; Du, H.-I.

2013-01-01

A 22.9 kV class hybrid fault current limiter (FCL) developed by Korea Electric Power Corporation and LS Industrial Systems in 2006 operates using the line commutation mechanism and begins to limit the fault current after the first half-cycle. The first peak of the fault current is available for protective coordination in the power system. However, it also produces a large electromagnetic force and imposes a huge stress on power facilities such as the main transformer and gas-insulated switchgear. In this study, we improved the operational characteristics of the hybrid FCL in order to reduce the first peak of the fault current. While maintaining the structure of the hybrid FCL system, we developed a superconducting module that detects and limits the fault current during the first half-cycle. To maintain the protective coordination capacity, the hybrid FCL was designed to reduce the first peak value of the fault current by up to approximately 30%. The superconducting module was also designed to produce a minimum AC loss, generating a small, uniform magnetic field distribution during normal operation. Performance tests confirmed that when applied to the hybrid FCL, the superconducting module showed successful current limiting operation without any damage.

Research and development of improved geothermal well logging techniques, tools and components (current projects, goals and status). Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lamers, M.D.

One of the key needs in the advancement of geothermal energy is availability of adequate subsurface measurements to aid the reservoir engineer in the development and operation of geothermal wells. Some current projects being sponsored by the U. S. Department of Energy's Division of Geothermal Energy pertaining to the development of improved well logging techniques, tools and components are described. An attempt is made to show how these projects contribute to improvement of geothermal logging technology in forming key elements of the overall program goals.

The Insertion of Human Factors Concerns into NextGen Programmatic Decisions

NASA Technical Reports Server (NTRS)

Beard, Bettina L.; Holbrook, Jon Brian; Seely, Rachel

2013-01-01

Since the costs of proposed improvements in air traffic management exceed available funding, FAA decision makers must select and prioritize what actually gets implemented. We discuss a set of methods to help forecast operational and human performance issues and benefits before new automation is introduced. This strategy could minimize the impact of politics, assist decision makers in selecting and prioritizing potential improvements, make the process more transparent and strengthen the link between the engineering and human factors domains.

A Hierarchical structure of key performance indicators for operation management and continuous improvement in production systems

PubMed Central

Kang, Ningxuan; Zhao, Cong; Li, Jingshan; Horst, John A.

2018-01-01

Key performance indicators (KPIs) are critical for manufacturing operation management and continuous improvement (CI). In modern manufacturing systems, KPIs are defined as a set of metrics to reflect operation performance, such as efficiency, throughput, availability, from productivity, quality and maintenance perspectives. Through continuous monitoring and measurement of KPIs, meaningful quantification and identification of different aspects of operation activities can be obtained, which enable and direct CI efforts. A set of 34 KPIs has been introduced in ISO 22400. However, the KPIs in a manufacturing system are not independent, and they may have intrinsic mutual relationships. The goal of this paper is to introduce a multi-level structure for identification and analysis of KPIs and their intrinsic relationships in production systems. Specifically, through such a hierarchical structure, we define and layer KPIs into levels of basic KPIs, comprehensive KPIs and their supporting metrics, and use it to investigate the relationships and dependencies between KPIs. Such a study can provide a useful tool for manufacturing engineers and managers to measure and utilize KPIs for CI. PMID:29398722

Use of MODIS Cloud Top Pressure to Improve Assimilation Yields of AIRS Radiances in GSI

NASA Technical Reports Server (NTRS)

Zavodsky, Bradley; Srikishen, Jayanthi

2014-01-01

Improvements to global and regional numerical weather prediction have been demonstrated through assimilation of data from NASA's Atmospheric Infrared Sounder (AIRS). Current operational data assimilation systems use AIRS radiances, but impact on regional forecasts has been much smaller than for global forecasts. Previously, it has been shown that cloud top designation associated with quality control procedures within the Gridpoint Statistical Interpolation (GSI) system used operationally by a number of Joint Center for Satellite Data Assimilation (JCSDA) partners may not provide the best representation of cloud top pressure (CTP). Because this designated CTP determines which channels are cloud-free and, thus, available for assimilation, ensuring the most accurate representation of this value is imperative to obtaining the greatest impact from satellite radiances. This paper examines the assimilation of hyperspectral sounder data used in operational numerical weather prediction by comparing analysis increments and numerical forecasts generated using operational techniques with a research technique that swaps CTP from the Moderate-resolution Imaging Spectroradiometer (MODIS) for the value of CTP calculated from the radiances within GSI.

A Hierarchical structure of key performance indicators for operation management and continuous improvement in production systems.

PubMed

Kang, Ningxuan; Zhao, Cong; Li, Jingshan; Horst, John A

2016-01-01

Key performance indicators (KPIs) are critical for manufacturing operation management and continuous improvement (CI). In modern manufacturing systems, KPIs are defined as a set of metrics to reflect operation performance, such as efficiency, throughput, availability, from productivity, quality and maintenance perspectives. Through continuous monitoring and measurement of KPIs, meaningful quantification and identification of different aspects of operation activities can be obtained, which enable and direct CI efforts. A set of 34 KPIs has been introduced in ISO 22400. However, the KPIs in a manufacturing system are not independent, and they may have intrinsic mutual relationships. The goal of this paper is to introduce a multi-level structure for identification and analysis of KPIs and their intrinsic relationships in production systems. Specifically, through such a hierarchical structure, we define and layer KPIs into levels of basic KPIs, comprehensive KPIs and their supporting metrics, and use it to investigate the relationships and dependencies between KPIs. Such a study can provide a useful tool for manufacturing engineers and managers to measure and utilize KPIs for CI.

Improving the performance of univariate control charts for abnormal detection and classification

NASA Astrophysics Data System (ADS)

Yiakopoulos, Christos; Koutsoudaki, Maria; Gryllias, Konstantinos; Antoniadis, Ioannis

2017-03-01

Bearing failures in rotating machinery can cause machine breakdown and economical loss, if no effective actions are taken on time. Therefore, it is of prime importance to detect accurately the presence of faults, especially at their early stage, to prevent sequent damage and reduce costly downtime. The machinery fault diagnosis follows a roadmap of data acquisition, feature extraction and diagnostic decision making, in which mechanical vibration fault feature extraction is the foundation and the key to obtain an accurate diagnostic result. A challenge in this area is the selection of the most sensitive features for various types of fault, especially when the characteristics of failures are difficult to be extracted. Thus, a plethora of complex data-driven fault diagnosis methods are fed by prominent features, which are extracted and reduced through traditional or modern algorithms. Since most of the available datasets are captured during normal operating conditions, the last decade a number of novelty detection methods, able to work when only normal data are available, have been developed. In this study, a hybrid method combining univariate control charts and a feature extraction scheme is introduced focusing towards an abnormal change detection and classification, under the assumption that measurements under normal operating conditions of the machinery are available. The feature extraction method integrates the morphological operators and the Morlet wavelets. The effectiveness of the proposed methodology is validated on two different experimental cases with bearing faults, demonstrating that the proposed approach can improve the fault detection and classification performance of conventional control charts.

Improvements of PKU PMECRIS for continuous hundred hours CW proton beam operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peng, S. X., E-mail: sxpeng@pku.edu.cn; Ren, H. T.; Zhang, T.

2016-02-15

In order to improve the source stability, a long term continuous wave (CW) proton beam experiment has been carried out with Peking University compact permanent magnet 2.45 GHz ECR ion source (PKU PMECRIS). Before such an experiment a lot of improvements and modifications were completed on the source body, the Faraday cup and the PKU ion source test bench. At the beginning of 2015, a continuous operation of PKU PMECRIS for 306 h with more than 50 mA CW beam was carried out after success of many short term tests. No plasma generator failure or high voltage breakdown was observedmore » during that running period and the proton source reliability is near 100%. Total beam availability, which is defined as 35-keV beam-on time divided by elapsed time, was higher than 99% [S. X. Peng et al., Chin. Phys. B 24(7), 075203 (2015)]. A re-inspection was performed after another additional 100 h operation (counting time) and no obvious sign of component failure was observed. Counting the previous source testing time together, this PMECRs longevity is now demonstrated to be greater than 460 h. This paper is mainly concentrated on the improvements for this long term experiment.« less

Evaluating the addition of oxaliplatin to single agent fluoropyrimidine in the treatment of locally advanced rectal cancer: a systematic review and meta-analysis.

PubMed

Thavaneswaran, Subotheni; Kok, Peey Sei; Price, Timothy

2017-10-01

Multimodality treatment of patients with locally advanced rectal cancer (LARC) has significantly improved local disease control, however the unaltered overall survival (OS) implicates an inability to further control micrometastases, providing rationale for intensified systemic treatment. A systematic review was conducted to evaluate the efficacy and toxicity of adding oxaliplatin to a fluoropyrimidine (intervention) compared with fluoropyrimidine alone (control) in the treatment of LARC. We searched CENTRAL, Medline Ovid, PubMed and EMBASE databases. Randomised trials comparing the intervention and control delivered either pre- or post-operatively were included. Seven trials involving 4444 patients were identified; five studies evaluated the intervention vs control preoperatively; one study peri-operatively; and one, post-operatively. There was no significant difference in OS with oxaliplatin addition, HR 0.89, 95% CI, 0.75 to 1.06. There was however an improvement in disease free survival, 3-year local and distant recurrence rates (RR) favouring oxaliplatin. Preoperative oxaliplatin improved pathological complete response (pCR), but with a greater toxicity and reduced compliance with radiation. There is no OS benefit with oxaliplatin, despite improved pCR, local and distant RR. Before drawing definitive conclusions, longer follow-up in included trials and availability of published data from other eligible studies, including the induction setting, are needed.

Method and system for monitoring and displaying engine performance parameters

NASA Technical Reports Server (NTRS)

Abbott, Terence S. (Inventor); Person, Lee H., Jr. (Inventor)

1988-01-01

The invention is believed a major improvement that will have a broad application in governmental and commercial aviation. It provides a dynamic method and system for monitoring and simultaneously displaying in easily scanned form the available, predicted, and actual thrust of a jet aircraft engine under actual operating conditions. The available and predicted thrusts are based on the performance of a functional model of the aircraft engine under the same operating conditions. Other critical performance parameters of the aircraft engine and functional model are generated and compared, the differences in value being simultaneously displayed in conjunction with the displayed thrust values. Thus, the displayed information permits the pilot to make power adjustments directly while keeping him aware of total performance at a glance of a single display panel.

Application of Satellite Based Augmentation Systems to Altitude Separation

NASA Astrophysics Data System (ADS)

Magny, Jean Pierre

This paper presents the application of GNSS1, or more precisely of Satellite Based Augmentation Systems (SBAS), to vertical separation for en-route, approach and landing operations. Potential improvements in terms of operational benefit and of safety are described for two main applications. First, vertical separation between en-route aircraft, which requires a system available across wide areas. SBAS (EGNOS, WAAS, and MSAS) are very well suited for this purpose before GNSS2 becomes available. And secondly, vertical separation from the ground during approach and landing, for which preliminary design principles of instrument approach procedures and safety issues are presented. Approach and landing phases are the subject of discussions within ICAO GNSS-P. En-route phases have been listed as GNSS-P future work and by RTCA for development of new equipments.

ADVANCEMENT OF THE RHIC BEAM ABORT KICKER SYSTEM.

DOE Office of Scientific and Technical Information (OSTI.GOV)

ZHANG,W.AHRENS,L.MI,J.OERTER,B.SANDBERG,J.WARBURTON,D.

2003-05-12

As one of the most critical system for RHIC operation, the beam abort kicker system has to be highly available, reliable, and stable for the entire operating range. Along with the RHIC commission and operation, consistent efforts have been spend to cope with immediate issues as well as inherited design issues. Major design changes have been implemented to achieve the higher operating voltage, longer high voltage hold-off time, fast retriggering and redundant triggering, and improved system protection, etc. Recent system test has demonstrated for the first time that both blue ring and yellow ring beam abort systems have achieved moremore » than 24 hours hold off time at desired operating voltage. In this paper, we report break down, thyratron reverse arcing, and to build a fast re-trigger system to reduce beam spreading in event of premature discharge.« less

A Final Approach Trajectory Model for Current Operations

NASA Technical Reports Server (NTRS)

Gong, Chester; Sadovsky, Alexander

2010-01-01

Predicting accurate trajectories with limited intent information is a challenge faced by air traffic management decision support tools in operation today. One such tool is the FAA's Terminal Proximity Alert system which is intended to assist controllers in maintaining safe separation of arrival aircraft during final approach. In an effort to improve the performance of such tools, two final approach trajectory models are proposed; one based on polynomial interpolation, the other on the Fourier transform. These models were tested against actual traffic data and used to study effects of the key final approach trajectory modeling parameters of wind, aircraft type, and weight class, on trajectory prediction accuracy. Using only the limited intent data available to today's ATM system, both the polynomial interpolation and Fourier transform models showed improved trajectory prediction accuracy over a baseline dead reckoning model. Analysis of actual arrival traffic showed that this improved trajectory prediction accuracy leads to improved inter-arrival separation prediction accuracy for longer look ahead times. The difference in mean inter-arrival separation prediction error between the Fourier transform and dead reckoning models was 0.2 nmi for a look ahead time of 120 sec, a 33 percent improvement, with a corresponding 32 percent improvement in standard deviation.

Fuzzy-based propagation of prior knowledge to improve large-scale image analysis pipelines

PubMed Central

Mikut, Ralf

2017-01-01

Many automatically analyzable scientific questions are well-posed and a variety of information about expected outcomes is available a priori. Although often neglected, this prior knowledge can be systematically exploited to make automated analysis operations sensitive to a desired phenomenon or to evaluate extracted content with respect to this prior knowledge. For instance, the performance of processing operators can be greatly enhanced by a more focused detection strategy and by direct information about the ambiguity inherent in the extracted data. We present a new concept that increases the result quality awareness of image analysis operators by estimating and distributing the degree of uncertainty involved in their output based on prior knowledge. This allows the use of simple processing operators that are suitable for analyzing large-scale spatiotemporal (3D+t) microscopy images without compromising result quality. On the foundation of fuzzy set theory, we transform available prior knowledge into a mathematical representation and extensively use it to enhance the result quality of various processing operators. These concepts are illustrated on a typical bioimage analysis pipeline comprised of seed point detection, segmentation, multiview fusion and tracking. The functionality of the proposed approach is further validated on a comprehensive simulated 3D+t benchmark data set that mimics embryonic development and on large-scale light-sheet microscopy data of a zebrafish embryo. The general concept introduced in this contribution represents a new approach to efficiently exploit prior knowledge to improve the result quality of image analysis pipelines. The generality of the concept makes it applicable to practically any field with processing strategies that are arranged as linear pipelines. The automated analysis of terabyte-scale microscopy data will especially benefit from sophisticated and efficient algorithms that enable a quantitative and fast readout. PMID:29095927

SIPT: a seismic refraction inverse modeling program for timeshare terminal computer systems

USGS Publications Warehouse

Scott, James Henry

1977-01-01

SIPB is an interactive Fortran computer program that was developed for use with a timeshare computer system with program control information submitted from a remote terminal, and output data displayed on the terminal or printed on a line printer. The program is an upgraded version of FSIPI (Scott, Tibbetts, and Burdick, 1972) with several major improvements in addition to .its adaptation to timeshare operation. The most significant improvement was made in the procedure for handling data from in-line offset shotpoints beyond the end shotpoints of the geophone spread. The changes and improvements are described, user's instructions are outlined, examples of input and output data for a test problem are presented, and the Fortran program is listed in this report. An upgraded batch-mode program, SIPB, is available for users who do not have a timeshare computer system available (Scott, 1977).

SIPB: a seismic refraction inverse modeling program for batch computer systems

USGS Publications Warehouse

Scott, James Henry

1977-01-01

SIPB is an interactive Fortran computer program that was developed for use with a timeshare computer system with program control information submitted from a remote terminal, and output data displayed on the terminal or printed on a line printer. The program is an upgraded version of FSIPI (Scott, Tibbetts, and Burdick, 1972) with several major improvements in addition to .its adaptation to timeshare operation. The most significant improvement was made in the procedure for handling data from in-line offset shotpoints beyond the end shotpoints of the geophone spread. The changes and improvements are described, user's instructions are outlined, examples of input and output data for a test problem are presented, and the Fortran program is listed in this report. An upgraded batch-mode program, SIPB, is available for users who do not have a timeshare computer system available (Scott, 1977).

Space and ground-based GNSS activities at NOAA

NASA Astrophysics Data System (ADS)

Cucurull, L.

2016-12-01

With the launch of the FORMOSAT-3/COSMIC satellites in April 2006, the availability of Global Navigation Satellite Systems (GNSS) Radio Occultation (RO) observations for operational Numerical Weather Prediction (NWP) applications began. GNSS RO profiles started being assimilated operationally in the major worldwide weather centers soon after. NOAA started assimilating RO data operationally in early 2007. After COSMIC, other missions carrying GNSS RO receivers became available for operational uses. The incorporation of RO observations into the operational assimilation systems was shown to improve global model forecast skill. Since its launch in 2006, the COSMIC constellation has been the mainstay of the global RO system. However, COSMIC is already past the end of its formal lifetime, and only three satellites are still operating. This has motivated NOAA to invest on the COSMIC-2 mission, a 12-satellite constellation, that will replace COSMIC. The first launch, in equatorial orbit, is planned for March 2017. In addition to the space-based component of the GNSS technique, NOAA is assimilating ground-based products into its operational regional models. Although most stations over CONUS provide estimates of Precipitable Water (PW), this is not the case outside the U.S., where the required auxiliary meteorological information is generally not available. Thus, in order to evaluate the impact of ground-based GNSS products on a global weather model, the assimilation of less derived products, such as zenith total delays, rather than PW, is necessary. The talk will include an update on current activities and future plans for the utilization of space and ground-based GNSS products at NOAA. In addition, an update on the COSMIC-2 mission will be discussed.

Domain Adaption of Parsing for Operative Notes

PubMed Central

Wang, Yan; Pakhomov, Serguei; Ryan, James O.; Melton, Genevieve B.

2016-01-01

Background Full syntactic parsing of clinical text as a part of clinical natural language processing (NLP) is critical for a wide range of applications, such as identification of adverse drug reactions, patient cohort identification, and gene interaction extraction. Several robust syntactic parsers are publicly available to produce linguistic representations for sentences. However, these existing parsers are mostly trained on general English text and often require adaptation for optimal performance on clinical text. Our objective was to adapt an existing general English parser for the clinical text of operative reports via lexicon augmentation, statistics adjusting, and grammar rules modification based on a set of biomedical text. Method The Stanford unlexicalized probabilistic context-free grammar (PCFG) parser lexicon was expanded with SPECIALIST lexicon along with statistics collected from a limited set of operative notes tagged with a two of POS taggers (GENIA tagger and MedPost). The most frequently occurring verb entries of the SPECIALIST lexicon were adjusted based on manual review of verb usage in operative notes. Stanford parser grammar production rules were also modified based on linguistic features of operative reports. An analogous approach was then applied to the GENIA corpus to test the generalizability of this approach to biomedical text. Results The new unlexicalized PCFG parser extended with the extra lexicon from SPECIALIST along with accurate statistics collected from an operative note corpus tagged with GENIA POS tagger improved the parser performance by 2.26% from 87.64% to 89.90%. There was a progressive improvement with the addition of multiple approaches. Most of the improvement occurred with lexicon augmentation combined with statistics from the operative notes corpus. Application of this approach on the GENIA corpus showed that parsing performance was boosted by 3.81% with a simple new grammar and the addition of the GENIA corpus lexicon. Conclusion Using statistics collected from clinical text tagged with POS taggers along with proper modification of grammars and lexicons of an unlexicalized PCFG parser can improve parsing performance. PMID:25661593

Reliability assessment and improvement for a fast corrector power supply in TPS

NASA Astrophysics Data System (ADS)

Liu, Kuo-Bin; Liu, Chen-Yao; Wang, Bao-Sheng; Wong, Yong Seng

2018-07-01

Fast Orbit Feedback System (FOFB) can be installed in a synchrotron light source to eliminate undesired disturbances and to improve the stability of beam orbit. The design and implementation of an accurate and reliable Fast Corrector Power Supply (FCPS) is essential to realize the effectiveness and availability of the FOFB. A reliability assessment for the FCPSs in the FOFB of Taiwan Photon Source (TPS) considering MOSFETs' temperatures is represented in this paper. The FCPS is composed of a full-bridge topology and a low-pass filter. A Hybrid Pulse Width Modulation (HPWM) requiring two MOSFETs in the full-bridge circuit to be operated at high frequency and the other two be operated at the output frequency is adopted to control the implemented FCPS. Due the characteristic of HPWM, the conduction loss and switching loss of each MOSFET in the FCPS is not same. Two of the MOSFETs in the full-bridge circuit will suffer higher temperatures and therefore the circuit reliability of FCPS is reduced. A Modified PWM Scheme (MPWMS) designed to average MOSFETs' temperatures and to improve circuit reliability is proposed in this paper. Experimental results measure the MOSFETs' temperatures of FCPS controlled by the HPWM and the proposed MPWMS. The reliability indices under different PWM controls are then assessed. From the experimental results, it can be observed that the reliability of FCPS using the proposed MPWMS can be improved because the MOSFETs' temperatures are closer. Since the reliability of FCPS can be enhanced, the availability of FOFB can also be improved.

Maria Auxiliadora Hospital in Lima, Peru as a model for neurosurgical outreach to international charity hospitals.

PubMed

Hayden, Melanie G; Hughes, Samuel; Hahn, Edward J; Aryan, Henry E; Levy, Michael L; Jandial, Rahul

2011-01-01

A myriad of geopolitical and financial obstacles have kept modern neurosurgery from effectively reaching the citizens of the developing world. Targeted neurosurgical outreach by academic neurosurgeons to equip neurosurgical operating theaters and train local neurosurgeons is one method to efficiently and cost effectively improve sustainable care provided by international charity hospitals. The International Neurosurgical Children's Association (INCA) effectively improved the available neurosurgical care in the Maria Auxiliadora Hospital of Lima, Peru through the advancement of local specialist education and training. Neurosurgical equipment and training were provided for the local neurosurgeons by a mission team from the University of California at San Diego. At the end of 3 years, with one intensive week trip per year, the host neurosurgeons were proficiently and independently applying microsurgical techniques to previously performed operations, and performing newly learned operations such as neuroendoscopy and minimally invasive neurosurgery. Our experiences may serve as a successful template for the execution of other small scale, sustainable neurosurgery missions worldwide.

Low levels of specularity support operational color constancy, particularly when surface and illumination geometry can be inferred

PubMed Central

Lee, Robert J.; Smithson, Hannah E.

2016-01-01

We tested whether surface specularity alone supports operational color constancy – the ability to discriminate changes in illumination or reflectance. Observers viewed short animations of illuminant or reflectance changes in rendered scenes containing a single spherical surface, and were asked to classify the change. Performance improved with increasing specularity, as predicted from regularities in chromatic statistics. Peak performance was impaired by spatial rearrangements of image pixels that disrupted the perception of illuminated surfaces, but was maintained with increased surface complexity. The characteristic chromatic transformations that are available with non-zero specularity are useful for operational color constancy, particularly if accompanied by appropriate perceptual organisation. PMID:26974938

The rationale for combining an online audiovisual curriculum with simulation to better educate general surgery trainees.

PubMed

AlJamal, Yazan N; Ali, Shahzad M; Ruparel, Raaj K; Brahmbhatt, Rushin D; Yadav, Siddhant; Farley, David R

2014-09-01

Surgery interns' training has historically been weighted toward patient care, operative observation, and sleeping when possible. With more protected free time and less clinical time, real educational hours for trainees in 2013 are precious. We created a 20-session (3 hours each) simulation curriculum (with pre- and post-tests) and a 24/7 online audiovisual (AV) curriculum for surgery interns. Friday morning simulation sessions emphasize operative skills and judgment. AV clips (using operating room, whiteboard, and simulation center videos) take learners through 20 different general surgery operations with follow-up quizzes. We report our early experience with this novel setup. Thirty-two surgical interns (2012-2013) attended simulation sessions on 20 separate subjects (hernia, breast, hepatobiliary, endocrine, etc). Post-test scores improved (P < .05) and trainees enjoyed using surgical skills for 3 hours each Friday morning (mean, >4.5; Likert scale, 1-5). The AV curriculum feedback is similar (mean, >4.3) and usage is available 24/7 preparing learners for both operating room and simulation sessions. Most simulation sessions utilize low-fidelity models to keep costs <$50 per session. Scores on our semiannual Surgical Olympics (mean score of 49.6 in July vs 82.9 in January; P < .05) improved significantly, suggesting that interns are improving their surgical skills and knowledge. Residents enjoy and learn from the step-by-step, in-house, AV curriculum and both appreciate and thrive on the 'hands-on' simulation sessions mimicking operations they see in real operating rooms. The cost of these programs is not prohibitive and the programs offer simulated repetitions for duty-hour-regulated trainees. Copyright © 2014 Mosby, Inc. All rights reserved.

Expanding the base for teaching of percutaneous coronary interventions: the explicit approach.

PubMed

Lanzer, Peter; Prechelt, Lutz

2011-02-15

Accelerate and improve the training and learning process of operators performing percutaneous coronary interventions (PCI). Operator cognitive, in particular decision-making skills and technical skills are a major factor for the success of coronary interventions. Currently, cognitive skills are commonly developed by three methods: (1) Cognitive learning of rules for which statistical evidence is available. This is very incomprehensive and isolates cognitive learning from skill acquisition. (2) Informal tutoring received from experienced operators, and (3) personal experience by trial-and-error are both very slow. We propose in this concept article a conceptual framework to elicit, capture, and transfer expert PCI skills to complement the current approach. This includes the development of an in-depth understanding of the nature of PCI skills, terminology, and nomenclature needed to streamline communication, propensity of reproducible performance assessment, and in particular an explication of intervention planning and intra-intervention decision-making. We illustrate the impact of improved decision-making by simulation results based on a stochastic model of intervention risk. We identify several key concepts that form the basis of this conceptual framework, in particular different risk types and the notions of strategy, interventional module, and tactic. The increasing complexity of cases have brought PCI to the point where the decision-making skills of master operators need to be made explicit to make them systematically learnable such that the skills of beginner and intermediate operators can be improved much faster than is currently possible. Copyright © 2010 Wiley-Liss, Inc.

Performance of ITER as a burning plasma experiment

NASA Astrophysics Data System (ADS)

Shimada, M.; Mukhovatov, V.; Federici, G.; Gribov, Y.; Kukushkin, A.; Murakami, Y.; Polevoi, A.; Pustovitov, V.; Sengoku, S.; Sugihara, M.

2004-02-01

Recent performance analysis has improved confidence in achieving Q (= fusion power/auxiliary heating power)geq 10 in inductive operation in ITER. Performance analysis based on empirical scalings shows the feasibility of achieving Q geq 10 in inductive operation, particularly with improved modelling of helium exhaust. Analysis has also indicated the possibility that ITER can potentially demonstrate Q ~ 50, enabling studies of self-heated plasmas. Theory-based core modelling indicates the need for a high pedestal temperature (3.2-5.3 keV) to achieve Q geq 10, which is in the range of projections with presently available pedestal scalings. Pellet injection from the high-field side would be useful in enhancing Q and reducing edge localized mode (ELM) heat load in high plasma current operation. If the ELM heat load is not acceptable, it could be made tolerable by further tilting the target plate. Steady state operation scenarios at Q = 5 have been developed with modest requirements on confinement improvement and beta (HH98(y,2) geq 1.3 and bgrN geq 2.6). Stabilization of the resistive wall modes (RWMs), required in such regimes, is feasible with the present saddle coils and power supplies with double-wall structures taken into account. Recent analysis shows a potential of high power steady state operation with a fusion power of 0.7 GW at Q ~ 8. Achievement of the required bgrN ~ 3.6 by RWM stabilization is a possibility. Further analysis is also needed on reduction of the divertor target heat load.

The First 2 Years of Activity of a Specialized Organ Procurement Center: Report of an Innovative Approach to Improve Organ Donation.

PubMed

Marsolais, P; Durand, P; Charbonney, E; Serri, K; Lagacé, A-M; Bernard, F; Albert, M

2017-06-01

The number of patients requiring organ transplants continues to outgrow the number of organs donated each year. In an attempt to improve the organ donation process and increase the number of organs available, we created a specialized multidisciplinary team within a specialized organ procurement center (OPC) with dedicated intensive care unit (ICU) beds and operating rooms. The OPC was staffed with ICU nurses, operating room nurses, organ donor management ICU physicians, and multidisciplinary staff. All organ donors within a designated geographic area were transferred to and managed within the OPC. During the first 2 years of operation, 126 patients were referred to the OPC. The OPC was in use for a total of 3527 h and involved 253 health workers. We retrieved 173 kidneys, 95 lungs, 68 livers, 37 hearts, and 13 pancreases for a total of 386 organs offered for transplantation. This translates to a total of 124.6 persons transplanted per million population, which compares most favorably to recently published numbers in developed countries. The OPC clearly demonstrates potential to increase the number of deceased donor organs available for transplant. Further studies are warranted to better understand the exact influence of the different components of the OPC on organ procurement. © 2016 The American Society of Transplantation and the American Society of Transplant Surgeons.

Transmission monitoring and control of strategic communication systems

NASA Astrophysics Data System (ADS)

Farrow, J. E.; Skerjanec, R. E.

1986-03-01

This paper discusses a minicomputer-based communication system monitor used by the U.S. Department of Defense to improve the service availability and reduce the operating costs of the new multichannel digital transmission systems. A brief history of the development of the monitor and a general description of the present-generation hardware and software are included.

Improvement of Operation Characteristics for MONOS Charge Trapping Flash Memory with SiGe Buried Channel

NASA Astrophysics Data System (ADS)

Hou, Zhao-Zhao; Wang, Gui-Lei; Yao, Jia-Xin; Zhang, Qing-Zhu; Yin, Hua-Xiang

2018-05-01

Not Available Supported by the National Science and Technology Major Project of China under Grant No 2013ZX02303007, the National Key Research and Development Program of China under Grant No 2016YFA0301701, and the Youth Innovation Promotion Association of the Chinese Academy of Sciences under Grant No 2016112.

Improved-Bandwidth Transimpedance Amplifier

NASA Technical Reports Server (NTRS)

Chapsky, Jacob

2009-01-01

The widest available operational amplifier, with the best voltage and current noise characteristics, is considered for transimpedance amplifier (TIA) applications where wide bandwidth is required to handle fast rising input signals (as for time-of-flight measurement cases). The added amplifier inside the TIA feedback loop can be configured to have slightly lower voltage gain than the bandwidth reduction factor.

Multi-mission Ni-H2 battery cell for the 1990's

NASA Technical Reports Server (NTRS)

Miller, Lee; Brill, Jack; Dodson, Gary

1989-01-01

A sufficient production, test and operational database is now available to permit design technology optimization for the next decade. The evolved battery cell design features standardized technology intended to support multiple type missions (e.g., both GEO and LEO). Design analyses and validation test cells demonstrate improved performance plus attractive specific-energy characteristics will be achieved.

Effects of intra-operative fluoroscopic 3D-imaging on peri-operative imaging strategy in calcaneal fracture surgery.

PubMed

Beerekamp, M S H; Backes, M; Schep, N W L; Ubbink, D T; Luitse, J S; Schepers, T; Goslings, J C

2017-12-01

Previous studies demonstrated that intra-operative fluoroscopic 3D-imaging (3D-imaging) in calcaneal fracture surgery is promising to prevent revision surgery and save costs. However, these studies limited their focus to corrections performed after 3D-imaging, thereby neglecting corrections after intra-operative fluoroscopic 2D-imaging (2D-imaging). The aim of this study was to assess the effects of additional 3D-imaging on intra-operative corrections, peri-operative imaging used, and patient-relevant outcomes compared to 2D-imaging alone. In this before-after study, data of adult patients who underwent open reduction and internal fixation (ORIF) of a calcaneal fracture between 2000 and 2014 in our level-I Trauma center were collected. 3D-imaging (BV Pulsera with 3D-RX, Philips Healthcare, Best, The Netherlands) was available as of 2007 at the surgeons' discretion. Patient and fracture characteristics, peri-operative imaging, intra-operative corrections and patient-relevant outcomes were collected from the hospital databases. Patients in whom additional 3D-imaging was applied were compared to those undergoing 2D-imaging alone. A total of 231 patients were included of whom 107 (46%) were operated with the use of 3D-imaging. No significant differences were found in baseline characteristics. The median duration of surgery was significantly longer when using 3D-imaging (2:08 vs. 1:54 h; p = 0.002). Corrections after additional 3D-imaging were performed in 53% of the patients. However, significantly fewer corrections were made after 2D-imaging when 3D-imaging was available (Risk difference (RD) -15%; 95% Confidence interval (CI) -29 to -2). Peri-operative imaging, besides intra-operative 3D-imaging, and patient-relevant outcomes were similar between groups. Intra-operative 3D-imaging provides additional information resulting in additional corrections. Moreover, 3D-imaging probably changed the surgeons' attitude to rely more on 3D-imaging, hence a 15%-decrease of corrections performed after 2D-imaging when 3D imaging was available. No substantiation for cost reduction was found through reduction in peri-operative imaging or in terms of improved patient-relevant outcomes.

rf improvements for Spallation Neutron Source H- ion sourcea)

NASA Astrophysics Data System (ADS)

Kang, Y. W.; Fuja, R.; Goulding, R. H.; Hardek, T.; Lee, S.-W.; McCarthy, M. P.; Piller, M. C.; Shin, K.; Stockli, M. P.; Welton, R. F.

2010-02-01

The Spallation Neutron Source at Oak Ridge National Laboratory is ramping up the accelerated proton beam power to 1.4 MW and just reached 1 MW. The rf-driven multicusp ion source that originates from the Lawrence Berkeley National Laboratory has been delivering ˜38 mA H- beam in the linac at 60 Hz, 0.9 ms. To improve availability, a rf-driven external antenna multicusp ion source with a water-cooled ceramic aluminum nitride (AlN) plasma chamber is developed. Computer modeling and simulations have been made to analyze and optimize the rf performance of the new ion source. Operational statistics and test runs with up to 56 mA medium energy beam transport beam current identify the 2 MHz rf system as a limiting factor in the system availability and beam production. Plasma ignition system is under development by using a separate 13 MHz system. To improve the availability of the rf power system with easier maintenance, we tested a 70 kV isolation transformer for the 80 kW, 6% duty cycle 2 MHz amplifier to power the ion source from a grounded solid-state amplifier.

rf improvements for Spallation Neutron Source H- ion source.

PubMed

Kang, Y W; Fuja, R; Goulding, R H; Hardek, T; Lee, S-W; McCarthy, M P; Piller, M C; Shin, K; Stockli, M P; Welton, R F

2010-02-01

The Spallation Neutron Source at Oak Ridge National Laboratory is ramping up the accelerated proton beam power to 1.4 MW and just reached 1 MW. The rf-driven multicusp ion source that originates from the Lawrence Berkeley National Laboratory has been delivering approximately 38 mA H(-) beam in the linac at 60 Hz, 0.9 ms. To improve availability, a rf-driven external antenna multicusp ion source with a water-cooled ceramic aluminum nitride (AlN) plasma chamber is developed. Computer modeling and simulations have been made to analyze and optimize the rf performance of the new ion source. Operational statistics and test runs with up to 56 mA medium energy beam transport beam current identify the 2 MHz rf system as a limiting factor in the system availability and beam production. Plasma ignition system is under development by using a separate 13 MHz system. To improve the availability of the rf power system with easier maintenance, we tested a 70 kV isolation transformer for the 80 kW, 6% duty cycle 2 MHz amplifier to power the ion source from a grounded solid-state amplifier.

Standardization of vitrinite reflectance measurements in shale petroleum systems: How accurate are my Ro data?

USGS Publications Warehouse

Hackley, Paul C.

2014-01-01

Vitrinite reflectance generally is considered the most robust thermal maturity parameter available for application to hydrocarbon exploration and petroleum system evaluation. However, until 2011 there was no standardized methodology available to provide guidelines for vitrinite reflectance measurements in shale. Efforts to correct this deficiency resulted in publication of ASTM D7708-11: Standard test method for microscopical determination of the reflectance of vitrinite dispersed in sedimentary rocks. In 2012-2013, an interlaboratory exercise was conducted to establish precision limits for the measurement technique. Six samples, representing a wide variety of shale, were tested in duplicate by 28 analysts in 22 laboratories from 14 countries. Samples ranged from immature to overmature (Ro 0.31-1.53%), from organic-rich to organic-lean (1-22 wt.% total organic carbon), and contained Type I (lacustrine), Type II (marine), and Type III (terrestrial) kerogens. Repeatability values (difference between repetitive results from same operator, same conditions) ranged from 0.03-0.11% absolute reflectance, whereas reproducibility values (difference between results obtained on same test material by different operators, different laboratories) ranged from 0.12-0.54% absolute reflectance. Repeatability and reproducibility degraded consistently with increasing maturity and decreasing organic content. However, samples with terrestrial kerogens (Type III) fell off this trend, showing improved levels of reproducibility due to higher vitrinite content and improved ease of identification. Operators did not consistently meet the reporting requirements of the test method, indicating that a common reporting template is required to improve data quality. The most difficult problem encountered was the petrographic distinction of solid bitumens and low-reflecting inert macerals from vitrinite when vitrinite occurred with reflectance ranges overlapping the other components. Discussion among participants suggested this problem could not be corrected via kerogen concentration or solvent extraction and is related to operator training and background. Poor reproducibility (0.54% absolute reflectance, related to increased anisotropy?) in the highest maturity sample (Ro 1.53%) suggests that vitrinite reflectance is not a highly reliable parameter in such rocks. Future work will investigate opportunities to improve reproducibility in similar high maturity, organic-lean shale varieties.

Commercial Demonstration of the Manufactured Aggregate Processing Technology Utilizing Spray Dryer Ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milton Wu; Paul Yuran

2006-12-31

Universal Aggregates LLC (UA) was awarded a cost sharing Co-operative Agreement from the Department of Energy (DOE) through the Power Plant Improvement Initiative Program (PPII) to design, construct and operate a lightweight aggregate manufacturing plant at the Birchwood Power Facility in King George, Virginia in October 2001. The Agreement was signed in November 2002. The installation and start-up expenses for the Birchwood Aggregate Facility are $19.5 million. The DOE share is $7.2 million (37%) and the UA share is $12.3 million (63%). The original project team consists of UA, SynAggs, LLC, CONSOL Energy Inc. and P. J. Dick, Inc. Usingmore » 115,000 ton per year of spray dryer ash (SDA), a dry FGD by-product from the power station, UA will produce 167,000 tons of manufactured lightweight aggregate for use in production of concrete masonry units (CMU). Manufacturing aggregate from FGD by-products can provide an economical high-volume use and substantially expand market for FGD by-products. Most of the FGD by-products are currently disposed of in landfills. Construction of the Birchwood Aggregate Facility was completed in March 2004. Operation startup was begun in April 2004. Plant Integration was initiated in December 2004. Integration includes mixing, extrusion, curing, crushing and screening. Lightweight aggregates with proper size gradation and bulk density were produced from the manufacturing aggregate plant and loaded on a stockpile for shipment. The shipped aggregates were used in a commercial block plant for CMU production. However, most of the production was made at low capacity factors and for a relatively short time in 2005. Several areas were identified as important factors to improve plant capacity and availability. Equipment and process control modifications and curing vessel clean up were made to improve plant operation in the first half of 2006. About 3,000 tons of crushed aggregate was produced in August 2006. UA is continuing to work to improve plant availability and throughput capacity and to produce quality lightweight aggregate for use in commercial applications.« less

BWR Servicing and Refueling Improvement Program: Phase I summary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perry, D.R.

1978-09-01

Under the U.S. Department of Energy sponsorship, General Electric Co. (GE) undertook a study of boiling water reactor (BWR) refueling outages for the purpose of recommending the development and demonstration of critical path time savings improvements. The Tennessee Valley Authority (TVA) joined the study as a subcontractor, providing monitoring assistance and making the Browns Ferry Site available for improvement demonstrations. Agreement was also reached with Georgia Power Co., Power Authority of the State of New York, and Commonwealth Edison Co. for monitoring and data collection at Hatch 1, FitzPatrick, and Quad Cities 1 nuclear plants, respectively. The objective was tomore » identify, develop, and demonstrate improved refueling, maintenance, and inspection procedures and equipment. The improvements recommended in this study are applicable to BWR nuclear plants currently in operation as well as those in the design and construction phases. The recommendations and outage information can be used as a basis to plan and conduct the first outages of new plants and to improve the planning and facilities of currently operating plants. Many of the recommendations can readily be incorporated in plants currently in the design and construction phases as well as in the design of future plants. Many of these recommended improvements can be implemented immediately by utilities without further technical development.« less

Improving Small Signal Stability through Operating Point Adjustment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Zhenyu; Zhou, Ning; Tuffner, Francis K.

2010-09-30

ModeMeter techniques for real-time small signal stability monitoring continue to mature, and more and more phasor measurements are available in power systems. It has come to the stage to bring modal information into real-time power system operation. This paper proposes to establish a procedure for Modal Analysis for Grid Operations (MANGO). Complementary to PSS’s and other traditional modulation-based control, MANGO aims to provide suggestions such as increasing generation or decreasing load for operators to mitigate low-frequency oscillations. Different from modulation-based control, the MANGO procedure proactively maintains adequate damping for all time, instead of reacting to disturbances when they occur. Effectmore » of operating points on small signal stability is presented in this paper. Implementation with existing operating procedures is discussed. Several approaches for modal sensitivity estimation are investigated to associate modal damping and operating parameters. The effectiveness of the MANGO procedure is confirmed through simulation studies of several test systems.« less

Potential impact of remote sensing data on sea-state analysis and prediction

NASA Technical Reports Server (NTRS)

Cardone, V. J.

1983-01-01

The severe North Atlantic storm which damaged the ocean liner Queen Elizabeth 2 (QE2) was studied to assess the impact of remotely sensed marine surface wind data obtained by SEASAT-A, on sea state specifications and forecasts. Alternate representations of the surface wind field in the QE2 storm were produced from the SEASAT enhanced data base, and from operational analyses based upon conventional data. The wind fields were used to drive a high resolution spectral ocean surface wave prediction model. Results show that sea state analyses would have been vastly improved during the period of storm formation and explosive development had remote sensing wind data been available in real time. A modest improvement in operational 12 to 24 hour wave forecasts would have followed automatically from the improved initial state specification made possible by the remote sensing data in both numerical and sea state prediction models. Significantly improved 24 to 48 hour wave forecasts require in addition to remote sensing data, refinement in the numerical and physical aspects of weather prediction models.

Flux-coherent series SQUID array magnetometers operating above 77 K with superior white flux noise than single-SQUIDs at 4.2 K

NASA Astrophysics Data System (ADS)

Chesca, Boris; John, Daniel; Mellor, Christopher J.

2015-10-01

A very promising direction to improve the sensitivity of magnetometers based on superconducting quantum interference devices (SQUIDs) is to build a series-array of N non-interacting SQUIDs operating flux-coherently, because in this case their voltage modulation depth, ΔV, linearly scales with N whereas the white flux noise SΦ1/2 decreases as 1/N1/2. Here, we report the realization of both these improvements in an advanced layout of very large SQUID arrays made of YBa2Cu3O7. Specially designed with large area narrow flux focusers for increased field sensitivity and improved flux-coherency, our arrays have extremely low values for SΦ1/2 between (0.25 and 0.44) μΦ0/Hz1/2 for temperatures in the range (77-83) K. In this respect, they outperform niobium/aluminium trilayer technology-based single-SQUIDs operating at 4.2 K. Moreover, with values for ΔV and transimpedance in the range of (10-17) mV and (0.3-2.5) kΩ, respectively, a direct connection to a low-noise room temperature amplifier is allowed, while matching for such readout is simplified and the available bandwidth is greatly increased. These landmark performances suggest such series SQUID arrays are ideal candidates to replace single-SQUIDs operating at 4.2 K in many applications.

Operations analysis (study 2.1). Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Wolfe, R. R.

1975-01-01

Subjects related to future STS operations concepts were investigated. The majority of effort was directed at assessing the benefits of automated space servicing concepts as related to improvements in payload procurement and shuttle utilization. Another subject was directed at understanding shuttle upper stage software development and recurring costs relative to total program projections. Space serving of automated payloads is addressed by examining the broad spectrum of payload applications with the belief that shared logistic operations will be a major contributor to reduction of future program costs. However, there are certain requirements for support of payload operations, such as availability of the payload, that may place demands upon the shuttle fleet. Because future projections of the NASA Mission Model are only representative of the payload traffic, it is important to recognize that it is the general character of operations that is significant rather than service to any single payload program.

Principles and Guidelines for Duty and Rest Scheduling in Commercial Aviation

NASA Technical Reports Server (NTRS)

Dinges, David F.; Graeber, R. Curtis; Rosekind, Mark R.; Samel, Alexander

1996-01-01

The aviation industry requires 24-hour activities to meet operational demands. Growth in global long-haul, regional, overnight cargo, and short-haul domestic operations will continue to increase these round-the-clock requirements. Flight crews must be available to support 24-hour-a-day operations to meet these industry demands. Both domestic and international aviation can also require crossing multiple time zones. Therefore, shift work, night work, irregular work schedules, unpredictable work schedules, and dm zone changes will continue to be commonplace components of the aviation industry. These factors pose known challenges to human physiology, and because they result in performance-impairing fatigue, they pose a risk to safety. It is critical to acknowledge and, whenever possible, incorporate scientific information on fatigue, human sleep, and circadian physiology into 24-hour aviation operations. Utilization of such scientific information can help promote crew performance and alertness during flight operations and thereby maintain and improve the safety margin.

Continuous quality improvement for the clinical decision unit.

PubMed

Mace, Sharon E

2004-01-01

Clinical decision units (CDUs) are a relatively new and growing area of medicine in which patients undergo rapid evaluation and treatment. Continuous quality improvement (CQI) is important for the establishment and functioning of CDUs. CQI in CDUs has many advantages: better CDU functioning, fulfillment of Joint Commission on Accreditation of Healthcare Organizations mandates, greater efficiency/productivity, increased job satisfaction, better performance improvement, data availability, and benchmarking. Key elements include a database with volume indicators, operational policies, clinical practice protocols (diagnosis specific/condition specific), monitors, benchmarks, and clinical pathways. Examples of these important parameters are given. The CQI process should be individualized for each CDU and hospital.

Expert training with standardized operative technique helps establish a successful penile prosthetics program for urologic resident education.

PubMed

King, Ashley B; Klausner, Adam P; Johnson, Corey M; Moore, Blake W; Wilson, Steven K; Grob, B Mayer

2011-10-01

The challenge of resident education in urologic surgery programs is to overcome disparity imparted by diverse patient populations, limited training times, and inequalities in the availability of expert surgical educators. Specifically, in the area of prosthetic urology, only a small proportion of programs have full-time faculty available to train residents in this discipline. To examine whether a new model using yearly training sessions from a recognized expert can establish a successful penile prosthetics program and result in better outcomes, higher case volumes, and willingness to perform more complex surgeries. A recognized expert conducted one to two operative training sessions yearly to teach standardized technique for penile prosthetics to residents. Each session consisted of three to four operative cases performed under the direct supervision of the expert. Retrospective data were collected from all penile prosthetic operations before (February, 2000 to June, 2004: N = 44) and after (July, 2004 to October, 2007: N = 79) implementation of these sessions. Outcomes reviewed included patient age, race, medical comorbidities, operative time, estimated blood loss, type of prosthesis, operative approach, drain usage, length of stay, and complications including revision/explantation rates. Statistical analysis was performed using Student's t-tests, Fisher's tests, and survival curves using the Kaplan-Meier technique (P value ≤ 0.05 to define statistical significance). Patient characteristics were not significantly different pre- vs. post-training. Operative time and estimated blood loss significantly decreased. Inflatable implants increased from 19/44 (43.2%, pre-training) to 69/79 (87.3%, post-training) (P < 0.01). Operations per year increased from 9.96 (pre-training) to 24 (post-training) (P < 0.01). Revision/explantation occurred in 11/44 patients (25%, pre-training) vs. 7/79 (8.9%, post-training) (P < 0.05). These data demonstrate that yearly sessions with a recognized expert can improve surgical outcomes, type, and volume of implants and can reduce explantation/revision rates. This represents an excellent model for improved training of urologic residents in penile prosthetics surgery. © 2011 International Society for Sexual Medicine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hadley, I.; Sinclair, C.I.K.; Magne, E.

This paper describes the life extension of a semi-submersible drilling rig built in the early 1970`s. A nominal design life of 20 years was estimated at the time of building; however, in the interim period, numerous improvements have been made in fatigue life estimation ad life improvement techniques, raising the possibility that a further 20 years of operation could be considered. The life extension strategy made use of a number of aspects of offshore technology which were not available at the time of construction of the rig. Finite element studies and results from offshore research programs were used to gaugemore » the effect of fatigue life improvement techniques. The program demonstrated the feasibility of extending the operation of the rig for a further 20 years, with the interval between in-service inspection increased to every five years. It also provided a valuable database of fracture toughness data for the rig materials, which may be used in future work to address reliability issues.« less

Canadian aeronautical mobile data trials

NASA Technical Reports Server (NTRS)

Pedersen, Allister; Pearson, Andrea

1993-01-01

This paper describes a series of aeronautical mobile data trials conducted on small aircraft (helicopters and fixed wing) utilizing a low-speed store-and-forward mobile data service. The paper outlines the user requirements for aeronautical mobile satellite communications. 'Flight following' and improved wide-area dispatch communications were identified as high priority requirements. A 'proof-of-concept' trial in a Cessna Skymaster aircraft is described. This trial identified certain development work as essential to the introduction of commercial service including antenna development, power supply modifications and doppler software modifications. Other improvements were also proposed. The initial aeronautical mobile data service available for pre-operational (Beta) trials is outlined. Pre-operational field trials commenced in October 1992 and consisted of installations on a Gralen Communications Inc. Cessna 177 and an Aerospatiale Astar 350 series light single engine helicopter. The paper concludes with a discussion of desirable near term mobile data service developments, commercial benefits, current safety benefits and potential future applications for improved safety.

Improved Methodology for Surface and Atmospheric Soundings, Error Estimates, and Quality Control Procedures: the AIRS Science Team Version-6 Retrieval Algorithm

NASA Technical Reports Server (NTRS)

Susskind, Joel; Blaisdell, John; Iredell, Lena

2014-01-01

The AIRS Science Team Version-6 AIRS/AMSU retrieval algorithm is now operational at the Goddard DISC. AIRS Version-6 level-2 products are generated near real-time at the Goddard DISC and all level-2 and level-3 products are available starting from September 2002. This paper describes some of the significant improvements in retrieval methodology contained in the Version-6 retrieval algorithm compared to that previously used in Version-5. In particular, the AIRS Science Team made major improvements with regard to the algorithms used to 1) derive surface skin temperature and surface spectral emissivity; 2) generate the initial state used to start the cloud clearing and retrieval procedures; and 3) derive error estimates and use them for Quality Control. Significant improvements have also been made in the generation of cloud parameters. In addition to the basic AIRS/AMSU mode, Version-6 also operates in an AIRS Only (AO) mode which produces results almost as good as those of the full AIRS/AMSU mode. This paper also demonstrates the improvements of some AIRS Version-6 and Version-6 AO products compared to those obtained using Version-5.

Evaluation Metrics for the Paragon XP/S-15

NASA Technical Reports Server (NTRS)

Traversat, Bernard; McNab, David; Nitzberg, Bill; Fineberg, Sam; Blaylock, Bruce T. (Technical Monitor)

1993-01-01

On February 17th 1993, the Numerical Aerodynamic Simulation (NAS) facility located at the NASA Ames Research Center installed a 224 node Intel Paragon XP/S-15 system. After its installation, the Paragon was found to be in a very immature state and was unable to support a NAS users' workload, composed of a wide range of development and production activities. As a first step towards addressing this problem, we implemented a set of metrics to objectively monitor the system as operating system and hardware upgrades were installed. The metrics were designed to measure four aspects of the system that we consider essential to support our workload: availability, utilization, functionality, and performance. This report presents the metrics collected from February 1993 to August 1993. Since its installation, the Paragon availability has improved from a low of 15% uptime to a high of 80%, while its utilization has remained low. Functionality and performance have improved from merely running one of the NAS Parallel Benchmarks to running all of them faster (between 1 and 2 times) than on the iPSC/860. In spite of the progress accomplished, fundamental limitations of the Paragon operating system are restricting the Paragon from supporting the NAS workload. The maximum operating system message passing (NORMA IPC) bandwidth was measured at 11 Mbytes/s, well below the peak hardware bandwidth (175 Mbytes/s), limiting overall virtual memory and Unix services (i.e. Disk and HiPPI I/O) performance. The high NX application message passing latency (184 microns), three times than on the iPSC/860, was found to significantly degrade performance of applications relying on small message sizes. The amount of memory available for an application was found to be approximately 10 Mbytes per node, indicating that the OS is taking more space than anticipated (6 Mbytes per node).

[Laparoscopic technique--which developments are possible?].

PubMed

Voges, U

1996-05-01

The progress of laparoscopy is influenced by both the medical and technical aspects. The development of endoscopes and various rigid instruments has increased the indication options. Nevertheless, several drawbacks remain, e.g. the limited spatial view, the missing sense of touch, and reduced mobility in the operation area. New 3D visual systems now introduce spatial view. Flexible instruments are being developed that allow thorough examination of organs. While these enhancements are now becoming available, research and development are making progress and preparing the next steps. One vision is the development of a telepresence and telemanipulation system. With it, at the patient's side we will have an endoscope guidance system and several instrument guidance systems, which will be telemanipulated from a control station. At the control station, a 3D picture from the operation scene, together with virtual reality simulation pictures will be available. Force reflection as well as palpatory sensing information will be readily available to the telesurgeon. These new developments will improve the quality of the surgery for the benefit of both the patient and surgeon. Furthermore, the training of new surgeons will be eased by the use of sophisticated simulators using virtual reality techniques. These and further technical developments will not only lead to an improvement in current laparoscopy procedures, but it can be expected that additional procedures will be developed that are not yet possible and accessible to laparoscopy.

Bringing High-Rate, CO2-Based Microbial Electrosynthesis Closer to Practical Implementation through Improved Electrode Design and Operating Conditions.

PubMed

Jourdin, Ludovic; Freguia, Stefano; Flexer, Victoria; Keller, Jurg

2016-02-16

The enhancement of microbial electrosynthesis (MES) of acetate from CO2 to performance levels that could potentially support practical implementations of the technology must go through the optimization of key design and operating conditions. We report that higher proton availability drastically increases the acetate production rate, with pH 5.2 found to be optimal, which will likely suppress methanogenic activity without inhibitor addition. Applied cathode potential as low as -1.1 V versus SHE still achieved 99% of electron recovery in the form of acetate at a current density of around -200 A m(-2). These current densities are leading to an exceptional acetate production rate of up to 1330 g m(-2) day(-1) at pH 6.7. Using highly open macroporous reticulated vitreous carbon electrodes with macropore sizes of about 0.6 mm in diameter was found to be optimal for achieving a good balance between total surface area available for biofilm formation and effective mass transfer between the bulk liquid and the electrode and biofilm surface. Furthermore, we also successfully demonstrated the use of a synthetic biogas mixture as carbon dioxide source, yielding similarly high MES performance as pure CO2. This would allow this process to be used effectively for both biogas quality improvement and conversion of the available CO2 to acetate.

Improved document image segmentation algorithm using multiresolution morphology

NASA Astrophysics Data System (ADS)

Bukhari, Syed Saqib; Shafait, Faisal; Breuel, Thomas M.

2011-01-01

Page segmentation into text and non-text elements is an essential preprocessing step before optical character recognition (OCR) operation. In case of poor segmentation, an OCR classification engine produces garbage characters due to the presence of non-text elements. This paper describes modifications to the text/non-text segmentation algorithm presented by Bloomberg,1 which is also available in his open-source Leptonica library.2The modifications result in significant improvements and achieved better segmentation accuracy than the original algorithm for UW-III, UNLV, ICDAR 2009 page segmentation competition test images and circuit diagram datasets.

Engine dynamic analysis with general nonlinear finite element codes. Part 2: Bearing element implementation overall numerical characteristics and benchmaking

NASA Technical Reports Server (NTRS)

Padovan, J.; Adams, M.; Fertis, J.; Zeid, I.; Lam, P.

1982-01-01

Finite element codes are used in modelling rotor-bearing-stator structure common to the turbine industry. Engine dynamic simulation is used by developing strategies which enable the use of available finite element codes. benchmarking the elements developed are benchmarked by incorporation into a general purpose code (ADINA); the numerical characteristics of finite element type rotor-bearing-stator simulations are evaluated through the use of various types of explicit/implicit numerical integration operators. Improving the overall numerical efficiency of the procedure is improved.

Equipment upgrades for the Pu-238 program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Congdon, J.W.; Stephens, W.D.; Marra, J.E.

1990-02-14

Much of the equipment and instrumentation in the Pu-238 production facilities is more than 15 years old. Significant improvements have been made in the available instrumentation, in particular, due to the application of microprocessors and lasers. The Actinide Technology Section of SRL has selected and is in the process of evaluating several state-of-the-art instruments which have potential applications in the Pu-238 program. The ease of operation and the accuracy of the instruments have been improved and, in most cases, the cost of the instruments have decreased. 5 refs.

Operational, quality, and risk management in the transfusion service: lessons learned.

PubMed

Goodnough, Lawrence Tim

2012-07-01

For general health care, the difference between quality and safety has been unclear for measurable patient outcomes. In contrast, in the transfusion service (TS), the relationship between quality and safety has been direct and demonstrable. Case studies are summarized to illustrate the relationship between operations, quality management, and risk management in the TS. In blood availability for elective surgery over 3 audited intervals, the incidence of patients undergoing elective surgery without available crossmatched blood that had been requested was 1:333, 1:328, and 1:225 for pre-quality improvement, post-quality improvement, and subsequent postintervention audit assessment, respectively. In event discovery reports (EDRs) over 2 years, incidence of biologic product deviation reports (Food and Drug Administration reportable) was successfully reduced from 60 biologic product deviation reports (12%) of 507 EDRs in 2009 to 42 (12%) of 336 EDRs in 2010. In wrong blood in tube, 102 specimens were identified (by a change in patient's ABO/Rh) from 176,711 type and screen/cross-match specimens received over a 5-year interval, detected either by previous patient record of ABO/Rh or by a second specimen for blood type confirmation implemented in our TS for the last 3 years. No known cases of "mismatched" red blood cell transfusion have occurred during this interval. There is an inverse relationship between resources/time expended on quality and risk management relative to volumes of operations in the TS. Laboratory-based initiatives that improve patient safety and clinical outcomes need to have resources aligned with the personnel and time required for quality management and risk management. Copyright © 2012 Elsevier Inc. All rights reserved.

An Integrated Gate Turnaround Management Concept Leveraging Big Data/Analytics for NAS Performance Improvements

NASA Technical Reports Server (NTRS)

Chung, William; Chachad, Girish; Hochstetler, Ronald

2016-01-01

The Integrated Gate Turnaround Management (IGTM) concept was developed to improve the gate turnaround performance at the airport by leveraging relevant historical data to support optimization of airport gate operations, which include: taxi to the gate, gate services, push back, taxi to the runway, and takeoff, based on available resources, constraints, and uncertainties. By analyzing events of gate operations, primary performance dependent attributes of these events were identified for the historical data analysis such that performance models can be developed based on uncertainties to support descriptive, predictive, and prescriptive functions. A system architecture was developed to examine system requirements in support of such a concept. An IGTM prototype was developed to demonstrate the concept using a distributed network and collaborative decision tools for stakeholders to meet on time pushback performance under uncertainties.

New PbSnTe heterojunction laser diode structures with improved performance

NASA Technical Reports Server (NTRS)

Fonstad, C. G.; Kasemset, D.; Hsieh, H. H.; Rotter, S.

1980-01-01

Several recent advances in the state-of-the-art of lead tin telluride double heterojunction laser diodes are summarized. Continuous Wave operation to 120 K and pulsed operation to 166 K with single, lowest order transverse mode emission to in excess of four times threshold at 80 K were achieved in buried stripe lasers fabricated by liquid phase epitaxy in the lattice-matched system, lead-tin telluride-lead telluride selenide. At the same time, liquid phase epitaxy was used to produce PbSnTe distributed feedback lasers with much broader continuous single mode tuning ranges than are available from Fabry-Perot lasers. The physics and philosophy behind these advances is as important as the structures and performance of the specific devices embodying the advances, particularly since structures are continually being evolved and the performance continues to be improved.

Diurnal evolution of wind structure and data availability measured by the DOE prototype radar system

NASA Astrophysics Data System (ADS)

Hirth, Brian D.; Schroeder, John L.; Guynes, Jerry G.

2017-11-01

A new Doppler radar prototype has been developed and deployed at Texas Tech University with a focus on enhancing the technologies’ capability to contribute to wind plant relevant complex flow measurements. In particular, improvements in data availability, total data coverage, and autonomous operation were targeted to enable contributions to a wider range of wind energy applications. Doppler radar offers rapid scan speeds, extended maximum range and excellent along-beam range resolution allowing for the simultaneous measurement of various wind phenomena ranging from regional and wind plant scales to inflow and wake flow assessment for an individual turbine. Data examples and performance improvements relative to a previous edition of the technology are presented, including insights into the influence of diurnal atmospheric stability evolution of wind structure and system performance.

A new adjustable parallel drill guide for internal fixation of femoral neck fracture: a developmental and experimental study.

PubMed

Yuenyongviwat, Varah; Tuntarattanapong, Pakjai; Tangtrakulwanich, Boonsin

2016-01-11

Internal fixation is one treatment for femoral neck fracture. Some devices and techniques reported improved accuracy and decreased fluoroscopic time. However, these are not widely used nowadays due to the lack of available special instruments and techniques. To improve the surgical procedure, the authors designed a new adjustable drill guide and tested the efficacy of the device. The authors developed a new adjustable drill guide for cannulated screw guide wire insertion for multiple screw fixation. Eight orthopaedic surgeons performed the experimental study to evaluate the efficacy of this device. Each surgeon performed guide wire insertion for multiple screw fixation in six synthetic femurs: three times with the new device and three times with the conventional technique. The fluoroscopic time, operative time and surgeon satisfaction were evaluated. In the operations with the new adjustable drill guide, the fluoroscopic and operative times were significantly lower than the operations with the conventional technique (p < 0.05). The mean score for the level of satisfaction of this device was also statistically significantly better (p = 0.02) than the conventional technique. The fluoroscopic and operative times with the new adjustable drill guide were reduced for multiple screw fixation of femoral neck fracture and the satisfaction of the surgeons was good.

Quality initiatives: lean approach to improving performance and efficiency in a radiology department.

PubMed

Kruskal, Jonathan B; Reedy, Allen; Pascal, Laurie; Rosen, Max P; Boiselle, Phillip M

2012-01-01

Many hospital radiology departments are adopting "lean" methods developed in automobile manufacturing to improve operational efficiency, eliminate waste, and optimize the value of their services. The lean approach, which emphasizes process analysis, has particular relevance to radiology departments, which depend on a smooth flow of patients and uninterrupted equipment function for efficient operation. However, the application of lean methods to isolated problems is not likely to improve overall efficiency or to produce a sustained improvement. Instead, the authors recommend a gradual but continuous and comprehensive "lean transformation" of work philosophy and workplace culture. Fundamental principles that must consistently be put into action to achieve such a transformation include equal involvement of and equal respect for all staff members, elimination of waste, standardization of work processes, improvement of flow in all processes, use of visual cues to communicate and inform, and use of specific tools to perform targeted data collection and analysis and to implement and guide change. Many categories of lean tools are available to facilitate these tasks: value stream mapping for visualizing the current state of a process and identifying activities that add no value; root cause analysis for determining the fundamental cause of a problem; team charters for planning, guiding, and communicating about change in a specific process; management dashboards for monitoring real-time developments; and a balanced scorecard for strategic oversight and planning in the areas of finance, customer service, internal operations, and staff development. © RSNA, 2012.

Mainstreaming Climate Change: Recent and Ongoing Efforts to Understand, Improve, and Expand Consideration of Climate Change in Federal Water Resources Planning

NASA Astrophysics Data System (ADS)

Ferguson, I. M.; McGuire, M.; Broman, D.; Gangopadhyay, S.

2017-12-01

The Bureau of Reclamation is a Federal agency tasked with developing and managing water supply and hydropower projects in the Western U.S. Climate and hydrologic variability and change significantly impact management actions and outcomes across Reclamation's programs and initiatives, including water resource planning and operations, infrastructure design and maintenance, hydropower generation, and ecosystem restoration, among others. Planning, design, and implementation of these programs therefore requires consideration of future climate and hydrologic conditions will impact program objectives. Over the past decade, Reclamation and other Federal agencies have adopted new guidelines, directives, and mandates that require consideration of climate change in water resources planning and decision making. Meanwhile, the scientific community has developed a large number of climate projections, along with an array of models, methods, and tools to facilitate consideration of climate projections in planning and decision making. However, water resources engineers, planners, and decision makers continue to face challenges regarding how best to use the available data and tools to support major decisions, including decisions regarding infrastructure investments and long-term operating criteria. This presentation will discuss recent and ongoing research towards understanding, improving, and expanding consideration of climate projections and related uncertainties in Federal water resources planning and decision making. These research efforts address a variety of challenges, including: How to choose between available climate projection datasets and related methods, models, and tools—many of which are considered experimental or research tools? How to select an appropriate decision framework when design or operating alternatives may differ between climate scenarios? How to effectively communicate results of a climate impacts analysis to decision makers? And, how to improve robustness and resilience of water resources systems in the face of significant uncertainty? Discussion will focus on the intersection between technical challenges and decision making paradigms and the need for improved scientist-decision maker engagement through the lens of this Federal water management agency.

Global operating theatre distribution and pulse oximetry supply: an estimation from reported data.

PubMed

Funk, Luke M; Weiser, Thomas G; Berry, William R; Lipsitz, Stuart R; Merry, Alan F; Enright, Angela C; Wilson, Iain H; Dziekan, Gerald; Gawande, Atul A

2010-09-25

Surgery is an essential part of health care, but resources to ensure the availability of surgical services are often inadequate. We estimated the global distribution of operating theatres and quantified the availability of pulse oximetry, which is an essential monitoring device during surgery and a potential measure of operating theatre resources. We calculated ratios of the number of operating theatres to hospital beds in seven geographical regions worldwide on the basis of profiles from 769 hospitals in 92 countries that participated in WHO's safe surgery saves lives initiative. We used hospital bed figures from 190 WHO member states to estimate the number of operating theatres per 100,000 people in 21 subregions throughout the world. To estimate availability of pulse oximetry, we sent surveys to anaesthesia providers in 72 countries selected to ensure a geographically and demographically diverse sample. A predictive regression model was used to estimate the pulse oximetry need for countries that did not provide data. The estimated number of operating theatres ranged from 1·0 (95% CI 0·9-1·2) per 100,000 people in west sub-Saharan Africa to 25·1 (20·9-30·1) per 100,000 in eastern Europe. High-income subregions all averaged more than 14 per 100,000 people, whereas all low-income subregions, representing 2·2 billion people, had fewer than two theatres per 100,000. Pulse oximetry data from 54 countries suggested that around 77,700 (63,195-95,533) theatres worldwide (19·2% [15·2-23·9]) were not equipped with pulse oximeters. Improvements in public-health strategies and monitoring are needed to reduce disparities for more than 2 billion people without adequate access to surgical care. WHO. Copyright © 2010 Elsevier Ltd. All rights reserved.

Enhanced Lighting Techniques and Augmented Reality to Improve Human Task Performance

NASA Technical Reports Server (NTRS)

Maida, James C.; Bowen, Charles K.; Pace, John W.

2005-01-01

One of the most versatile tools designed for use on the International Space Station (ISS) is the Special Purpose Dexterous Manipulator (SPDM) robot. Operators for this system are trained at NASA Johnson Space Center (JSC) using a robotic simulator, the Dexterous Manipulator Trainer (DMT), which performs most SPDM functions under normal static Earth gravitational forces. The SPDM is controlled from a standard Robotic Workstation. A key feature of the SPDM and DMT is the Force/Moment Accommodation (FMA) system, which limits the contact forces and moments acting on the robot components, on its payload, an Orbital Replaceable Unit (ORU), and on the receptacle for the ORU. The FMA system helps to automatically alleviate any binding of the ORU as it is inserted or withdrawn from a receptacle, but it is limited in its correction capability. A successful ORU insertion generally requires that the reference axes of the ORU and receptacle be aligned to within approximately 0.25 inch and 0.5 degree of nominal values. The only guides available for the operator to achieve these alignment tolerances are views from any available video cameras. No special registration markings are provided on the ORU or receptacle, so the operator must use their intrinsic features in the video display to perform the pre-insertion alignment task. Since optimum camera views may not be available, and dynamic orbital lighting conditions may limit viewing periods, long times are anticipated for performing some ORU insertion or extraction operations. This study explored the feasibility of using augmented reality (AR) to assist with SPDM operations. Geometric graphical symbols were overlaid on the end effector (EE) camera view to afford cues to assist the operator in attaining adequate pre-insertion ORU alignment.

Improved Evolutionary Hybrids for Flexible Ligand Docking in Autodock

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belew, R.K.; Hart, W.E.; Morris, G.M.

1999-01-27

In this paper we evaluate the design of the hybrid evolutionary algorithms (EAs) that are currently used to perform flexible ligand binding in the Autodock docking software. Hybrid EAs incorporate specialized operators that exploit domain-specific features to accelerate an EA's search. We consider hybrid EAs that use an integrated local search operator to reline individuals within each iteration of the search. We evaluate several factors that impact the efficacy of a hybrid EA, and we propose new hybrid EAs that provide more robust convergence to low-energy docking configurations than the methods currently available in Autodock.

ADDJUST-A View of the First 25 Years

NASA Technical Reports Server (NTRS)

Nieberding, Joe; Williams, Craig H.

2015-01-01

Various technologies and innovative launch operations were developed during the 50 years of the Centaur upper stage—the first launch vehicle to use high performing liquid hydrogen fuel. One innovation was “ADDJUST”, which enabled the successful negotiation of upper level winds measured only hours before launch. Initial causes for its creation, development, and operation during countdown are detailed. Problem definition, wind measuring/monitoring process, pitch and yaw steering coefficient generation, loads analysis, angle of attack, major risks/concerns, and anecdotal recollections are provided. Launch availability improved from as low as 55 to 95 percent due to ADDJUST, which is still in use.

Balancing Flood Risk and Water Supply in California: Policy Search Combining Short-Term Forecast Ensembles and Groundwater Recharge

NASA Astrophysics Data System (ADS)

Herman, J. D.; Steinschneider, S.; Nayak, M. A.

2017-12-01

Short-term weather forecasts are not codified into the operating policies of federal, multi-purpose reservoirs, despite their potential to improve service provision. This is particularly true for facilities that provide flood protection and water supply, since the potential flood damages are often too severe to accept the risk of inaccurate forecasts. Instead, operators must maintain empty storage capacity to mitigate flood risk, even if the system is currently in drought, as occurred in California from 2012-2016. This study investigates the potential for forecast-informed operating rules to improve water supply efficiency while maintaining flood protection, combining state-of-the-art weather hindcasts with a novel tree-based policy optimization framework. We hypothesize that forecasts need only accurately predict the occurrence of a storm, rather than its intensity, to be effective in regions like California where wintertime, synoptic-scale storms dominate the flood regime. We also investigate the potential for downstream groundwater injection to improve the utility of forecasts. These hypotheses are tested in a case study of Folsom Reservoir on the American River. Because available weather hindcasts are relatively short (10-20 years), we propose a new statistical framework to develop synthetic forecasts to assess the risk associated with inaccurate forecasts. The efficiency of operating policies is tested across a range of scenarios that include varying forecast skill and additional groundwater pumping capacity. Results suggest that the combined use of groundwater storage and short-term weather forecasts can substantially improve the tradeoff between water supply and flood control objectives in large, multi-purpose reservoirs in California.

Early full weight-bearing versus 6-week partial weight-bearing after open wedge high tibial osteotomy leads to earlier improvement of the clinical results: a prospective, randomised evaluation.

PubMed

Schröter, S; Ateschrang, A; Löwe, W; Nakayama, H; Stöckle, U; Ihle, C

2017-01-01

Open wedge high tibial osteotomy is a widespread treatment option in patients with varus malalignment and medial compartment osteoarthritis. There is no standardised protocol for post-operative rehabilitation available. The purpose of this study was to compare two post-operative rehabilitation protocols and to evaluate the clinical outcome of early full weight-bearing after open wedge HTO. One hundred and twenty consecutive patients with varus malalignment and medial compartment osteoarthritis received an open wedge HTO using an angular locking plate fixation between December 2008 and December 2011. All patients were assigned randomly into one of two groups with different post-operative rehabilitation protocols (11-day vs. 6-week 20-kg partial weight-bearing). Clinical outcome was evaluated using established instruments (Lequesne, Lysholm, HSS and IKDC scores) preoperatively, 6, 12 and 18 months post-operatively. Deformity analysis was performed preoperatively and during follow-up. All clinical scores showed a significant pre- to post-operative improvement. After 6 months, there was a higher improvement in the group of early full weight-bearing. The difference between preoperative and 6-month follow-up for the group with early full weight-bearing and for the group with 20-kg PWB for 6 weeks was 28 ± 26 and 18 ± 22, respectively, for the Lysholm score and -5.0 ± 5.1 and -3.0 ± 3.6, respectively, for the Lequesne score. Early full weight-bearing (11-day 20-kg partial weight-bearing) after open wedge HTO without bone graft leads to earlier improvement of the clinical results and can be recommended for post-operative rehabilitation after open wedge HTO and fixation with an angular locking plate. Therapeutic study, Level I.

Evaluation of Improved Pushback Forecasts Derived from Airline Ground Operations Data

NASA Technical Reports Server (NTRS)

Carr, Francis; Theis, Georg; Feron, Eric; Clarke, John-Paul

2003-01-01

Accurate and timely predictions of airline pushbacks can potentially lead to improved performance of automated decision-support tools for airport surface traffic, thus reducing the variability and average duration of costly airline delays. One factor which affects the realization of these benefits is the level of uncertainty inherent in the turn processes. To characterize this inherent uncertainty, three techniques are developed for predicting time-to-go until pushback as a function of available ground-time; elapsed ground-time; and the status (not-started/in-progress/completed) of individual turn processes (cleaning, fueling, etc.). These techniques are tested against a large and detailed dataset covering approximately l0(exp 4) real-world turn operations obtained through collaboration with Deutsche Lufthansa AG. Even after the dataset is filtered to obtain a sample of turn operations with minimal uncertainty, the standard deviation of forecast error for all three techniques is lower-bounded away from zero, indicating that turn operations have a significant stochastic component. This lower-bound result shows that decision-support tools must be designed to incorporate robust mechanisms for coping with pushback demand stochasticity, rather than treating the pushback demand process as a known deterministic input.

DOE explosives safety manual

NASA Astrophysics Data System (ADS)

1990-05-01

The Department of Energy (DOE) policy requires that all activities be conducted in a manner that protects the safety of the public and provides a safe and healthful workplace for employees. DOE has also prescribed that all personnel be protected in any explosives operation undertaken. The level of safety provided shall be at least equivalent to that of the best industrial practice. The risk of death or serious injury shall be limited to the lowest practicable minimum. DOE and contractors shall continually review their explosives operations with the aim of achieving further refinements and improvements in safety practices and protective features. This manual describes the Department's explosive safety requirements applicable to operations involving the development, testing, handling, and processing of explosives or assemblies containing explosives. It is intended to reflect the state-of-the-art in explosives safety. In addition, it is essential that applicable criteria and requirements for implementing this policy be readily available and known to those responsible for conducting DOE programs. This document shall be periodically reviewed and updated to establish new requirements as appropriate. Users are requested to submit suggestions for improving the DOE Explosives Safety Manual through their appropriate Operations Office to the Office of Quality Programs.

Life Cycle Water Consumption and Water Resource Assessment for Utility-Scale Geothermal Systems: An In-Depth Analysis of Historical and Forthcoming EGS Projects

DOE Data Explorer

Schroeder, Jenna N.

2013-08-31

This report is the third in a series of reports sponsored by the U.S. Department of Energy Geothermal Technologies Program in which a range of water-related issues surrounding geothermal power production are evaluated. The first report made an initial attempt at quantifying the life cycle fresh water requirements of geothermal power-generating systems and explored operational and environmental concerns related to the geochemical composition of geothermal fluids. The initial analysis of life cycle fresh water consumption of geothermal power-generating systems identified that operational water requirements consumed the vast majority of water across the life cycle. However, it relied upon limited operational water consumption data and did not account for belowground operational losses for enhanced geothermal systems (EGSs). A second report presented an initial assessment of fresh water demand for future growth in utility-scale geothermal power generation. The current analysis builds upon this work to improve life cycle fresh water consumption estimates and incorporates regional water availability into the resource assessment to improve the identification of areas where future growth in geothermal electricity generation may encounter water challenges.

Entanglement preservation by continuous distillation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mundarain, D.; Orszag, M.

2009-05-15

We study the two-qubit entanglement preservation for a system in the presence of independent thermal baths. We use a combination of filtering operations and distillation protocols as a series of frequent measurements on the system. It is shown that a small fraction of the total amount of available copies of the system preserves or even improves its initial entanglement during the evolution.

77 FR 43903 - Intent To Prepare an Environmental Impact Statement for Proposed Transit Improvements to the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-26

... Administration (FTA), as the lead federal agency, and the Chicago Transit Authority (CTA) published a Notice of... interested parties that the EIS will no longer be a Tier 1 EIS as originally proposed. The methodology and... analysis are available on the CTA Web site www.transitchicago.com/rpmproject . The CTA operates the rapid...

Improved Operation Characteristics for Nonvolatile Charge-Trapping Memory Capacitors with High-κ Dielectrics and SiGe Epitaxial Substrates

NASA Astrophysics Data System (ADS)

Hou, Zhao-Zhao; Wang, Gui-Lei; Xiang, Jin-Juan; Yao, Jia-Xin; Wu, Zhen-Hua; Zhang, Qing-Zhu; Yin, Hua-Xiang

2017-08-01

Not Available Supported by the National Science and Technology Major Project of China under Grant No 2013ZX02303007, the National Key Research and Development Program of China under Grant No 2016YFA0301701, and the Youth Innovation Promotion Association of the Chinese Academy of Sciences under Grant No 2016112.

Multi-mission Ni-H2 battery cells for the 1990's

NASA Technical Reports Server (NTRS)

Miller, Lee; Brill, Jack; Dodson, Gary

1989-01-01

A sufficient production, test and operational database is now available to permit design technology optimization for the next decade. The evolved battery cell design features standardized technology intended to support multiple type missions (e.g., both GEO and LEO). Design analysis and validation test cells demonstrate that improved performance plus attractive specific-energy characteristics will be achieved.

A Conceptual Framework for Analyzing Terrorist Groups,

DTIC Science & Technology

1985-06-01

level of future terrorist operations, the impact of arrests, etc. The identification of these gaps should provide the impetus to improved collection in...act. The principal advantage, however, of the conceptual framework is its ability to absorb new information as it becomes available, providing the...and indicate how long they have been targets. (Types: Diplomatic, business, military, police, airlines, private citizens, utilities, energy facilities

USDA Forest Service mobile satellite communications applications

NASA Technical Reports Server (NTRS)

Warren, John R.

1990-01-01

The airborne IR signal processing system being developed will require the use of mobile satellite communications to achieve its full capability and improvement in delivery timeliness of processed IR data to the Fire Staff. There are numerous other beneficial uses, both during wildland fire management operations or in daily routine tasks, which will also benefit from the availability of reliable communications from remote areas.

A Review of Information on Institutionalized Youths and the ECIA Chapter I Neglected or Delinquent Program.

ERIC Educational Resources Information Center

Marks, Ellen L.

This paper reviews and summarizes available information on the neglected or delinquent youth population, on education programs for delinquent youth, and on the Neglected or Delinquent (N or D) program funded under Chapter 1 of the Education Consolidation and Improvement Act that serves a portion of that population residing in state-operated or…

Improved Impact Hazard Assessment with Existing Radar Sites and a New 70-m Southern Hemisphere Radar Installation

NASA Technical Reports Server (NTRS)

Giorgini, J. D.; Slade, M. A.; Silva, A.; Preston, R. A.; Brozovic, M.; Taylor, P. A.; Magri, C.

2009-01-01

Add radar capability to the existing southern hemisphere 70-m Deep Space Network (DSN) site at Canberra, Australia, thereby increasing by 1.5-2x the observing time available for high-precision NEO trajectory refinement and characterization. Estimated cost: approx.$16 million over 3 years, $2.5 million/year for operations (FY09).

Assessment of preventive measures for accidental blood exposure in operating theaters: a survey of 20 hospitals in Northern France.

PubMed

Tarantola, Arnaud; Golliot, Franck; L'Heriteau, François; Lebascle, Karin; Ha, Catherine; Farret, Danièle; Bignon, Sylvie; Smaïl, Amar; Doutrellot-Philippon, Catherine; Astagneau, Pascal; Bouvet, Elisabeth

2006-08-01

Accidental exposures to blood of body fluids (ABE) expose health care workers (HCW) to the risk of occupational infection. Our aim was to assess the prevention equipment available in the operating theater (OT) with reference to guidelines or recommendations and its use by the staff in that OT on that day and past history of ABE. Correspondents of the Centre de Coordination de la Lutte contre les Infections Nosocomiales (CCLIN) Paris-Nord ABE Surveillance Taskforce carried out an observational multicenter survey in 20 volunteer French hospitals. In total, 260 operating staff (including 151 surgeons) were investigated. Forty-nine of the 260 (18.8%) staff said they double-gloved for all patients and procedures, changing gloves hourly. Blunt-tipped suture needles were available in 49.1% of OT; 42 of 76 (55.3%) of the surgeons in these OT said they never used them. Overall, 60% and 64% of surgeons had never self-tested for HIV and hepatitis C virus (HCV), respectively. Fifty-five surgeons said they had sustained a total of 96 needlestick injuries during the month preceding the survey. Ten of these surgeons had notified of 1 needlestick injury each to the occupational health department of their hospital (notification rate, 10.4%). The occurrence of needlestick injury remained high in operating personnel in France in 2000. Although hospitals may improve access to protective devices, operating staff mindful of safety in the OT should increase their use of available devices, their knowledge of their own serostatus, and their ABE notification rate to guide well-targeted prevention efforts.

[Importance of parathyroid SPECT and 99mTc scintigraphy, and of clinical, laboratorial, ultrasonographic and citologic correlation in the pre-operative localization of the parathyroid adenoma - pictorial assay].

PubMed

Oliveira, Marco Antônio Condé de; Maeda, Sérgio Setsuo; Dreyer, Patrícia; Lobo, Alberto; Andrade, Victor Piana de; Hoff, Ana O; Biscolla, Rosa Paula Mello; Smanio, Paola; Brandão, Cynthia M A; Vieira, José G

2010-06-01

In patients with primary hyperparathyroidism, candidates for surgical intervention, the parathyroid pre-operative localization is of fundamental importance in planning the appropriate surgical approach. The additional acquisition of SPECT and Technetium-99m images, during parathyroid scintigraphy with Sestamibi, is not common practice. Usually, only planar image acquisition, 15 minutes prior and 2 hours after radiopharmaceutical administration, is performed. In our experience, the complete protocol in parathyroid scintigraphy increases the accuracy of pre-operative parathyroid localization. The complete utilization of all available nuclear medicine methods (SPECT e 99mTc) and image interpretation in a multidisciplinary context can improve the accuracy of parathyroid scintigraphy.

Earth based approaches to enhancing the health and safety of space operations

NASA Technical Reports Server (NTRS)

Koller, A. M., Jr.

1985-01-01

This paper provides an overview of the current state of our earth based knowledge of space safety hazards; identification of several key areas of concern for space operations; and proposed approaches to providing technology enhancement and information needed to improve the health and safety to those conducting space operations. Included are a review of the identified hazards for space oeprations by hazard classification; a summarization of the information currently available on space experiences and an assessment of potential hazards for long duration spaceflight; a discussion of potential failure modes and their significance for Space Station work: and an assessment of current work which indicates additional research and experimentation which can only be accomplished in actual space missions.

Characterization of Reactivity Controlled Compression Ignition (RCCI) Using Premixed Gasoline and Direct-Injected Gasoline with a Cetane Improver on a Multi-Cylinder Engine

DOE PAGES

Dempsey, Adam B.; Curran, Scott; Reitz, Rolf D.

2015-04-14

The focus of the present paper was to characterize Reactivity Controlled Compression Ignition (RCCI) using a single-fuel approach of gasoline and gasoline mixed with a commercially available cetane improver on a multi-cylinder engine. RCCI was achieved by port-injecting a certification grade 96 research octane gasoline and direct-injecting the same gasoline mixed with various levels of a cetane improver, 2-ethylhexyl nitrate (EHN). The EHN volume percentages investigated in the direct-injected fuel were 10, 5, and 2.5%. The combustion phasing controllability and emissions of the different fueling combinations were characterized at 2300 rpm and 4.2 bar brake mean effective pressure over amore » variety of parametric investigations including direct injection timing, premixed gasoline percentage, and intake temperature. Comparisons were made to gasoline/diesel RCCI operation on the same engine platform at nominally the same operating condition. The experiments were conducted on a modern four cylinder light-duty diesel engine that was modified with a port-fuel injection system while maintaining the stock direct injection fuel system. The pistons were modified for highly premixed operation and feature an open shallow bowl design. The results indicate that the authority to control the combustion phasing through the fuel delivery strategy (e.g., direct injection timing or premixed gasoline percentage) is not a strong function of the EHN concentration in the direct-injected fuel. It was also observed that NOx emissions are a strong function of the global EHN concentration in-cylinder and the combustion phasing. Finally, in general, NOx emissions are significantly elevated for gasoline/gasoline+EHN operation compared with gasoline/diesel RCCI operation at a given operating condition.« less

Unique Datasets Collected by NOAA Hurricane Hunter Aircraft during the 2017 Atlantic Hurricane Season

NASA Astrophysics Data System (ADS)

Zawislak, J.; Reasor, P.

2017-12-01

Each year, NOAA's Atlantic Oceanographic & Meteorological Laboratory (AOML) Hurricane Research Division (HRD), in partnership with the National Hurricane Center (NHC) and NOAA's Environmental Modeling Center (EMC), operates a hurricane field program, the Intensity Forecast Experiment (IFEX). The experiment leverages the NOAA P-3 and G-IV hurricane hunter aircraft, based at NOAA's Office of Marine and Aviation Operations (OMAO) Aircraft Operations Center (AOC). The goals of IFEX are to improve understanding of physical processes in tropical cyclones (TCs), improve operational forecasts of TC intensity, structure, and rainfall by providing data into operational numerical modeling systems, and to develop and refine measurement technologies. This season the IFEX program, leveraging mainly operationally tasked EMC and NHC missions, sampled extensively Hurricanes Harvey, Irma, Jose, Maria, and Nate, as well as Tropical Storm Franklin. We will contribute to this important session by providing an overview of aircraft missions into these storms, guidance on the datasets made available from instruments onboard the P-3 and G-IV, and will offer some perspective on the science that can be addressed with these unique datasets, such as the value of those datasets towards model forecast improvement. NOAA aircraft sampled these storms during critical periods of intensification, and for Hurricanes Harvey and Irma, just prior to the devastating landfalls in the Caribbean and United States. The unique instrument suite on the P-3 offers inner core observations of the three-dimensional precipitation and vortex structure, lower troposphere (boundary layer) thermodynamic properties, and surface wind speed. In contrast, the G-IV flies at higher altitudes, sampling the environment surrounding the storms, and provides deep-tropospheric soundings from dropsondes.

Operation of International Monitoring System Network

NASA Astrophysics Data System (ADS)

Nikolova, Svetlana; Araujo, Fernando; Aktas, Kadircan; Malakhova, Marina; Otsuka, Riyo; Han, Dongmei; Assef, Thierry; Nava, Elisabetta; Mickevicius, Sigitas; Agrebi, Abdelouaheb

2015-04-01

The IMS is a globally distributed network of monitoring facilities using sensors from four technologies: seismic, hydroacoustic, infrasound and radionuclide. It is designed to detect the seismic and acoustic waves produced by nuclear test explosions and the subsequently released radioactive isotopes. Monitoring stations transmit their data to the IDC in Vienna, Austria, over a global private network known as the GCI. Since 2013, the data availability (DA) requirements for IMS stations account for quality of the data, meaning that in calculation of data availability data should be exclude if: - there is no input from sensor (SHI technology); - the signal consists of constant values (SHI technology); Even more strict are requirements for the DA of the radionuclide (particulate and noble gas) stations - received data have to be analyzed, reviewed and categorized by IDC analysts. In order to satisfy the strict data and network availability requirements of the IMS Network, the operation of the facilities and the GCI are managed by IDC Operations. Operations has following main functions: - to ensure proper operation and functioning of the stations; - to ensure proper operation and functioning of the GCI; - to ensure efficient management of the stations in IDC; - to provide network oversight and incident management. At the core of the IMS Network operations are a series of tools for: monitoring the stations' state of health and data quality, troubleshooting incidents, communicating with internal and external stakeholders, and reporting. The new requirements for data availability increased the importance of the raw data quality monitoring. This task is addressed by development of additional tools for easy and fast identifying problems in data acquisition, regular activities to check compliance of the station parameters with acquired data by scheduled calibration of the seismic network, review of the samples by certified radionuclide laboratories. The DA for the networks of different technologies in 2014 is: Primary seismic (PS) network - 95.70%, Infrasound network (IS) - 97.68%, Hydroacoustic network (HA) - 88.78%, Auxiliary Seismic - 86.07%; Radionuclide Particulate - 83.01% and Radionuclide Noble Gas -75.06%. IDC's strategy for further improving operations and management of the stations and meeting DA requirements is: - further development of tools and procedures to effectively identify and support troubleshooting of problems by the Station Operators; - effective support to the station operators to develop tailored Operation and Maintenance plans for their stations; - focus on early identification of the raw data quality problems at the station in order to support timely resolution; - extensive training programme for station operators (joined effort of IDC and IMS).

Engineering for Autonomous Seismic Stations at the IRIS PASSCAL Instrument Center

NASA Astrophysics Data System (ADS)

Anderson, K. R.; Carpenter, P.; Beaudoin, B. C.; Parker, T.; Hebert, J.; Childs, D.; Chung, P.; Reusch, A. M.

2015-12-01

The NSF funded Incorporated Research Institutions for Seismology (IRIS) through New Mexico Tech operates the PASSCAL Instrument Center (PIC) in Socorro New Mexico. The engineering effort at the PIC seeks to optimize seismic station operations for all portable experiments, include those in extremely remote and harsh polar environments. Recent advances have resulted in improved station design, allowing improved operational efficiencies, data quality return and reduction in station logistics associated with installation, maintenance and decommissioning of stations. These include: Battery and power system designs. Incorporating primary Lithium Thionyl Chloride (LTC) technology with rechargeable Lithium Iron Phosphate (LiFePO4) batteries allows systems to operate in areas with long-term solar autonomy (high latitudes). Development includes charge controller systems to switch between primary and secondary technologies efficiently. Enclosures: Engineered solutions to efficiently manage waste heat, maintain operational environment and provide light-weight and durable housing for seismic instrumentation. Communications: In collaboration with Xeos Technologies Inc., we deliver Iridium-based SOH/Command and Control telemetry as well as full bandwidth seismic data communications in high latitude environments at low power requirements. Smaller-lighter-instrumentation: Through the GEOICE MRI, we are working with Nanometrics on next generation "all-in-one" seismic systems that can be deployed in polar environments - easing logistics, minimizing installation time and improving data quality return for these expensive deployments. All autonomous station designs are openly and freely available at the IRIS PASSCAL webpage (www.passcal.nmt.edu/polar/design-drawings). More information on GEOICE and data quality from various seismometer emplacements will be presented in other posters at this AGU meeting.

RTEMS SMP and MTAPI for Efficient Multi-Core Space Applications on LEON3/LEON4 Processors

NASA Astrophysics Data System (ADS)

Cederman, Daniel; Hellstrom, Daniel; Sherrill, Joel; Bloom, Gedare; Patte, Mathieu; Zulianello, Marco

2015-09-01

This paper presents the final result of an European Space Agency (ESA) activity aimed at improving the software support for LEON processors used in SMP configurations. One of the benefits of using a multicore system in a SMP configuration is that in many instances it is possible to better utilize the available processing resources by load balancing between cores. This however comes with the cost of having to synchronize operations between cores, leading to increased complexity. While in an AMP system one can use multiple instances of operating systems that are only uni-processor capable, a SMP system requires the operating system to be written to support multicore systems. In this activity we have improved and extended the SMP support of the RTEMS real-time operating system and ensured that it fully supports the multicore capable LEON processors. The targeted hardware in the activity has been the GR712RC, a dual-core core LEON3FT processor, and the functional prototype of ESA's Next Generation Multiprocessor (NGMP), a quad core LEON4 processor. The final version of the NGMP is now available as a product under the name GR740. An implementation of the Multicore Task Management API (MTAPI) has been developed as part of this activity to aid in the parallelization of applications for RTEMS SMP. It allows for simplified development of parallel applications using the task-based programming model. An existing space application, the Gaia Video Processing Unit, has been ported to RTEMS SMP using the MTAPI implementation to demonstrate the feasibility and usefulness of multicore processors for space payload software. The activity is funded by ESA under contract 4000108560/13/NL/JK. Gedare Bloom is supported in part by NSF CNS-0934725.

Using Facility Condition Assessments to Identify Actions Related to Infrastructure

NASA Technical Reports Server (NTRS)

Rubert, Kennedy F.

2010-01-01

To support cost effective, quality research it is essential that laboratory and testing facilities are maintained in a continuous and reliable state of availability at all times. NASA Langley Research Center (LaRC) and its maintenance contractor, Jacobs Technology, Inc. Research Operations, Maintenance, and Engineering (ROME) group, are in the process of implementing a combined Facility Condition Assessment (FCA) and Reliability Centered Maintenance (RCM) program to improve asset management and overall reliability of testing equipment in facilities such as wind tunnels. Specific areas are being identified for improvement, the deferred maintenance cost is being estimated, and priority is being assigned against facilities where conditions have been allowed to deteriorate. This assessment serves to assist in determining where to commit available funds on the Center. RCM methodologies are being reviewed and enhanced to assure that appropriate preventive, predictive, and facilities/equipment acceptance techniques are incorporated to prolong lifecycle availability and assure reliability at minimum cost. The results from the program have been favorable, better enabling LaRC to manage assets prudently.

Quantifying High Frequency Skill and Relative Cost of Two Physics Packages for an Operational Spectral Wave Model

NASA Astrophysics Data System (ADS)

Edwards, K. L.; Siqueira, S. A.; Rogers, W. E.

2017-12-01

Simulating WAves Nearshore (SWAN) is one of the two phase-averaged spectral models used by the U.S. Navy for forecasting waves. The source term package available during SWAN's first validation for operational use in 2002 is referred to here as "SWAN-ST1". Since then, improvements to the source term package were implemented (SWAN-ST6). One outcome of the new package is better skill within the higher frequencies of the spectrum, where SWAN-ST1 gives non-physical response to changes in wind speed and non-physical response to presence of swell in the lower frequencies. However, SWAN-ST6 is typically 25% more expensive computationally than SWAN-ST1, so it is worthwhile to estimate its benefit to operational cases, where computation time is a primary concern. To validate SWAN-ST6 and quantify its improvement over SWAN-ST1, we apply the model to two geographic regions—the Northern Gulf of Mexico (NGoM) and Southern California (SoCal) coasts. The NGoM case is typified by smaller fetch and smaller swell contribution. We analyze the NGoM case for a year (2010 July-2011 Aug.); and the SoCal application for summer (2016 July-Aug.) and winter (2017 Jan.-Feb.) seasons. We compare results to available buoy data. The wave parameter mean square slope (MSS) is included in this study, since it is sensitive to accuracy (or lack thereof) at higher frequencies, as it is weighted by frequency to the fourth power. Model-data comparisons for the NGoM case show little benefit to using SWAN-ST6; both models highly correlate with observations, a result attributable to a) the lack of swell and b) the fact that the shorter dominant periods in this basin imply that available buoys typically measure very little of the spectral tail (e.g. 2 to 4 times the peak frequency). Model-data comparisons for the SoCal test case show that SWAN-ST6 performs at least as well but most often better than SWAN-ST1. The improvement is almost negligible for the lower order moments, significant wave height and period, which are less sensitive to the spectral tail. However, SWAN-ST6 in the SoCal case dramatically improves the comparisons of MSS relative to SWAN-ST1. Thus, results show that, in cases where the wave climate and frequency range of buoy data permit validation of the spectral tail, skill of MSS prediction is dramatically improved with the new source term package.

Capacity and reliability analyses with applications to power quality

NASA Astrophysics Data System (ADS)

Azam, Mohammad; Tu, Fang; Shlapak, Yuri; Kirubarajan, Thiagalingam; Pattipati, Krishna R.; Karanam, Rajaiah

2001-07-01

The deregulation of energy markets, the ongoing advances in communication networks, the proliferation of intelligent metering and protective power devices, and the standardization of software/hardware interfaces are creating a dramatic shift in the way facilities acquire and utilize information about their power usage. The currently available power management systems gather a vast amount of information in the form of power usage, voltages, currents, and their time-dependent waveforms from a variety of devices (for example, circuit breakers, transformers, energy and power quality meters, protective relays, programmable logic controllers, motor control centers). What is lacking is an information processing and decision support infrastructure to harness this voluminous information into usable operational and management knowledge to handle the health of their equipment and power quality, minimize downtime and outages, and to optimize operations to improve productivity. This paper considers the problem of evaluating the capacity and reliability analyses of power systems with very high availability requirements (e.g., systems providing energy to data centers and communication networks with desired availability of up to 0.9999999). The real-time capacity and margin analysis helps operators to plan for additional loads and to schedule repair/replacement activities. The reliability analysis, based on computationally efficient sum of disjoint products, enables analysts to decide the optimum levels of redundancy, aids operators in prioritizing the maintenance options for a given budget and monitoring the system for capacity margin. The resulting analytical and software tool is demonstrated on a sample data center.

Using crowdsourced web content for informing water systems operations in snow-dominated catchments

NASA Astrophysics Data System (ADS)

Giuliani, Matteo; Castelletti, Andrea; Fedorov, Roman; Fraternali, Piero

2016-12-01

Snow is a key component of the hydrologic cycle in many regions of the world. Despite recent advances in environmental monitoring that are making a wide range of data available, continuous snow monitoring systems that can collect data at high spatial and temporal resolution are not well established yet, especially in inaccessible high-latitude or mountainous regions. The unprecedented availability of user-generated data on the web is opening new opportunities for enhancing real-time monitoring and modeling of environmental systems based on data that are public, low-cost, and spatiotemporally dense. In this paper, we contribute a novel crowdsourcing procedure for extracting snow-related information from public web images, either produced by users or generated by touristic webcams. A fully automated process fetches mountain images from multiple sources, identifies the peaks present therein, and estimates virtual snow indexes representing a proxy of the snow-covered area. Our procedure has the potential for complementing traditional snow-related information, minimizing costs and efforts for obtaining the virtual snow indexes and, at the same time, maximizing the portability of the procedure to several locations where such public images are available. The operational value of the obtained virtual snow indexes is assessed for a real-world water-management problem, the regulation of Lake Como, where we use these indexes for informing the daily operations of the lake. Numerical results show that such information is effective in extending the anticipation capacity of the lake operations, ultimately improving the system performance.

Improving oceanographic data delivery through pipeline processing in a Commercial Cloud Services environment: the Australian Integrated Marine Observing System

NASA Astrophysics Data System (ADS)

Besnard, Laurent; Blain, Peter; Mancini, Sebastien; Proctor, Roger

2017-04-01

The Integrated Marine Observing System (IMOS) is a national project funded by the Australian government established to deliver ocean observations to the marine and climate science community. Now in its 10th year its mission is to undertake systematic and sustained observations and to turn them into data, products and analyses that can be freely used and reused for broad societal benefits. As IMOS has matured as an observing system expectation on the system's availability and reliability has also increased and IMOS is now seen as delivering 'operational' information. In responding to this expectation, IMOS has relocated its services to the commercial cloud service Amazon Web Services. This has enabled IMOS to improve the system architecture, utilizing more advanced features like object storage (S3 - Simple Storage Service) and autoscaling features, and introducing new checking procedures in a pipeline approach. This has improved data availability and resilience while protecting against human errors in data handling and providing a more efficient ingestion process.

Performance evaluation of haptic hand-controllers in a robot-assisted surgical system.

PubMed

Zareinia, Kourosh; Maddahi, Yaser; Ng, Canaan; Sepehri, Nariman; Sutherland, Garnette R

2015-12-01

This paper presents the experimental evaluation of three commercially available haptic hand-controllers to evaluate which was more suitable to the participants. Two surgeons and seven engineers performed two peg-in-hole tasks with different levels of difficulty. Each operator guided the end-effector of a Kuka manipulator that held surgical forceps and was equipped with a surgical microscope. Sigma 7, HD(2) and PHANToM Premium 3.0 hand-controllers were compared. Ten measures were adopted to evaluate operators' performances with respect to effort, speed and accuracy in completing a task, operator improvement during the tests, and the force applied by each haptic device. The best performance was observed with the Premium 3.0; the hand-piece was able to be held in a similar way to that used by surgeons to hold conventional tools. Hand-controllers with a linkage structure similar to the human upper extremity take advantage of the inherent human brain connectome, resulting in improved surgeon performance during robotic-assisted surgery. Copyright © 2015 John Wiley & Sons, Ltd.

Applications systems verification and transfer project. Volume 1: Operational applications of satellite snow cover observations: Executive summary. [usefulness of satellite snow-cover data for water yield prediction

NASA Technical Reports Server (NTRS)

Rango, A.

1981-01-01

Both LANDSAT and NOAA satellite data were used in improving snowmelt runoff forecasts. When the satellite snow cover data were tested in both empirical seasonal runoff estimation and short term modeling approaches, a definite potential for reducing forecast error was evident. A cost benefit analysis run in conjunction with the snow mapping indicated a $36.5 million annual benefit accruing from a one percent improvement in forecast accuracy using the snow cover data for the western United States. The annual cost of employing the system would be $505,000. The snow mapping has proven that satellite snow cover data can be used to reduce snowmelt runoff forecast error in a cost effective manner once all operational satellite data are available within 72 hours after acquisition. Executive summaries of the individual snow mapping projects are presented.

Utilizing Commercial Real Estate Owner and Investor Data to Analyze the Financial Performance of Energy Efficient, High-Performance Office Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cloutier, Deborah; Hosseini, Farshid; White, Andrew

Evidence has shown that owning and operating energy-efficient, high-performance, “green” properties results in multiple benefits including lower utility bills, higher rents, improved occupancy, and greater net operating income. However, it is difficult to isolate and control moderating factors to identify the specific drivers behind improved financial performance and value to investors that results from sustainability in real estate. DOE is interested in facilitating deeper investigation of the correlation between energy efficiency and financial performance, reducing data acquisition and matching challenges, and developing a stronger understanding of how sustainable design and energy efficiency impact value. DOE commissioned this pilot study tomore » test the logistical and empirical procedures required to establish a Commercial Real Estate Data Aggregation & Trends Analysis lab, determine the potential benefits available through the lab, and contribute to the existing body of evidence in this field.« less

The supply of pharmaceuticals in humanitarian assistance missions: implications for military operations.

PubMed

Mahmood, Maysaa; Riley, Kevin; Bennett, David; Anderson, Warner

2011-08-01

In this article, we provide an overview of key international guidelines governing the supply of pharmaceuticals during disasters and complex emergencies. We review the World Health Organization's guidelines on pharmaceutical supply chain management and highlight their relevance for military humanitarian assistance missions. Given the important role of pharmaceuticals in addressing population health needs during humanitarian emergencies, a good understanding of how pharmaceuticals are supplied at the local level in different countries can help military health personnel identify the most appropriate supply options. Familiarity with international guidelines involved in cross-border movement of pharmaceuticals can improve the ability of military personnel to communicate more effectively with other actors involved in humanitarian and development spheres. Enhancing the knowledge base available to military personnel in terms of existing supply models and funding procedures can improve the effectiveness of humanitarian military operations and invite policy changes necessary to establish more flexible acquisition and funding regulations.

Reliability design and verification for launch-vehicle propulsion systems - Report of an AIAA Workshop, Washington, DC, May 16, 17, 1989

NASA Astrophysics Data System (ADS)

Launch vehicle propulsion system reliability considerations during the design and verification processes are discussed. The tools available for predicting and minimizing anomalies or failure modes are described and objectives for validating advanced launch system propulsion reliability are listed. Methods for ensuring vehicle/propulsion system interface reliability are examined and improvements in the propulsion system development process are suggested to improve reliability in launch operations. Also, possible approaches to streamline the specification and procurement process are given. It is suggested that government and industry should define reliability program requirements and manage production and operations activities in a manner that provides control over reliability drivers. Also, it is recommended that sufficient funds should be invested in design, development, test, and evaluation processes to ensure that reliability is not inappropriately subordinated to other management considerations.

Evaluation of improved operational standard tropospheric NO2 retrievals from Ozone Monitoring Instrument using in situ and surface-based NO2 observations

NASA Astrophysics Data System (ADS)

Celarier, E. A.; Lamsal, L.; Krotkov, N. A.; Bucsela, E. J.; Herman, J. R.; Dickerson, R. R.; He, H.; Brent, L. C.; Retscher, C.; Swartz, W. H.; Gleason, J. F.

2011-12-01

Nitrogen oxides are key actors in air quality and climate change. Column observations of tropospheric NO2 from the nadir-veiwing satellite sensors have been widely used to understand sources and chemistry of NOx. We have implemented several improvements to the operational algorithm developed at NASA GSFC and retrieved tropospheric NO2. Here we evaluate the new product using in situ surface measurements at the SEARCH, AQS/EPA, and NAPS networks, in situ aircraft (DISCOVER-AQ and RAMMPP), and ground-based PANDORA and DOAS measurements. The agreement among these data is within the uncertainty of measurements. The new OMI tropospheric NO2 product available at high spatial resolution is valuable to evaluate chemical transport models, to examine spatial and temporal pattern of NOx emissions, to provide top-down constraints to surface NOx emissions, and to estimate NOx lifetimes.

Optimising energy recovery and use of chemicals, resources and materials in modern waste-to-energy plants.

PubMed

De Greef, J; Villani, K; Goethals, J; Van Belle, H; Van Caneghem, J; Vandecasteele, C

2013-11-01

Due to ongoing developments in the EU waste policy, Waste-to-Energy (WtE) plants are to be optimized beyond current acceptance levels. In this paper, a non-exhaustive overview of advanced technical improvements is presented and illustrated with facts and figures from state-of-the-art combustion plants for municipal solid waste (MSW). Some of the data included originate from regular WtE plant operation - before and after optimisation - as well as from defined plant-scale research. Aspects of energy efficiency and (re-)use of chemicals, resources and materials are discussed and support, in light of best available techniques (BAT), the idea that WtE plant performance still can be improved significantly, without direct need for expensive techniques, tools or re-design. In first instance, diagnostic skills and a thorough understanding of processes and operations allow for reclaiming the silent optimisation potential. Copyright © 2013 Elsevier Ltd. All rights reserved.

Industrial use of land observation satellite systems

NASA Technical Reports Server (NTRS)

Henderson, F. B., III

1984-01-01

The principal industrial users of land observation satellite systems are the geological industries; oil/gas, mining, and engineering/environmental companies. The primary system used is LANDSAT/MSS. Currently, use is also being made of the limited amounts of SKYLAB photography, SEASAT and SIR-A radar, and the new LANDSAT/TM data available. Although considered experimental, LANDSAT data is now used operationally by several hundred exploration and engineering companies worldwide as a vastly improved geological mapping tool to help direct more expensive geophysical and drilling phases, leading to more efficient decision-making and results. Future needs include global LANDSAT/TM; higher spatial resolution; stereo and radar; improved data handling, processing distribution and archiving systems, and integrated geographical information systems (GIS). For a promising future, governments must provide overall continuity (government and/or private sector) of such systems, insure continued government R and D, and commit to operating internationally under the civil Open Skies policy.

Operational Evaluation of Tug/Barge Systems.

DTIC Science & Technology

1979-07-01

it would be expected that push-towing on the oceans would have developed long ago. However, the simple pin and wire/ chain lashings used on the rivers...better maneuverability available with push-towing. Thus, they began deepening the notches and using sophisticated cable/ chain linking and chafing...denied. But since mechanical linkages would result in increased manning rd capital costs, they instead began to develop improved cable/ chain linkages

The Joe 2010 Joint Operating Environment

DTIC Science & Technology

2010-02-18

mitigate the effects of water pollution. By the year 2030, advances in technology may provide many nations with more efficient, sustainable, and...both the number of forces and the time required to rebuild or improve water infrastructure, leave-behind water -purification technology could contribute...represent two of the most important aspects of military effectiveness . The former occurs during peace, when there is time available to think through

Genetic effects on stand-level uniformity, and above- and belowground dry mass production in juvenile loblolly pine

Treesearch

Michael J. Aspinwall; John S. King; Steven E. McKeand; Bronson P. Bullock

2012-01-01

Several decades of tree improvement operations have drastically increased loblolly pine plantation productivity in the southern U.S. (McKeand et al., 2003). This work has lead to the availability of a number of highly productive open-pollinated and full-sib families (McKeand et al., 2006). In addition, vegetative propagation (somatic embryogenesis) has also made it...

HS3 Data Catalog

NASA Technical Reports Server (NTRS)

Emory, Amber Elizabeth; Chirica, Dan Cristian; Doyle, Jim

2013-01-01

This presentation covered the original plan for the Hurricane and Severe Storm Sentinel (HS3) Data Catalog available through the ESPO HS3 mission page (http://espo.nasa.gov/missions/hs3/) and provided examples of Model Products, Operational Products, and Research (Instrument) Products from the 2012 field campaign. The presentation also covered lessons learned and suggested improvements to the Data Catalog for the upcoming 2013 HS3 field campaign.

Jet Lag in Military Operations: Field Trial of L-Tryptophan in Reducing Sleep-Loss Effects

DTIC Science & Technology

1986-03-21

in decreased fatigue and desire to sleep. improved information processing and concentration, faster temperature rhythm adaptation, greater encoding...tea, soda containing caffeine, chocolate milk, chocolate candy, etc.). Beverages without caffeine could be ingested, Including decaffeinated coffee...subjects wore devices for ambulatory monitoring of physiological processes . We used the Medilog 9-channel recorder available from Oxford Hedilog, Inc

Planning for Production of Freshwater Fish Fry in a Variable Climate in Northern Thailand.

PubMed

Uppanunchai, Anuwat; Apirumanekul, Chusit; Lebel, Louis

2015-10-01

Provision of adequate numbers of quality fish fry is often a key constraint on aquaculture development. The management of climate-related risks in hatchery and nursery management operations has not received much attention, but is likely to be a key element of successful adaptation to climate change in the aquaculture sector. This study explored the sensitivities and vulnerability of freshwater fish fry production in 15 government hatcheries across Northern Thailand to climate variability and evaluated the robustness of the proposed adaptation measures. This study found that hatcheries have to consider several factors when planning production, including: taking into account farmer demand; production capacity of the hatchery; availability of water resources; local climate and other area factors; and, individual species requirements. Nile tilapia is the most commonly cultured species of freshwater fish. Most fry production is done in the wet season, as cold spells and drought conditions disrupt hatchery production and reduce fish farm demand in the dry season. In the wet season, some hatcheries are impacted by floods. Using a set of scenarios to capture major uncertainties and variability in climate, this study suggests a couple of strategies that should help make hatchery operations more climate change resilient, in particular: improving hatchery operations and management to deal better with risks under current climate variability; improving monitoring and information systems so that emerging climate-related risks are known sooner and understood better; and, research and development on alternative species, breeding programs, improving water management and other features of hatchery operations.

Proposed teleworking platform for workstations supporting multimedia medical applications

NASA Astrophysics Data System (ADS)

Orphanos, George; Kanellopoulos, Dimitris; Prentzas, Lambros; Koubias, Stavros

1993-09-01

Teleworking refers to the usage of telecommunication facilities to improve human to human collaboration and enhance performance of work. This paper focuses on the way teleworking affects medicine. In particular, a teleworking platform is proposed to support multimedia medical applications embedded into RISC-based workstations. In order to support the teleworking platform, current commercially available products have to be taken into consideration and a range of new technologies need to be developed and made available. In this paper, we put emphasis on a RISC-based workstation, UNIXTM operating system, communication protocols capable to support the teleworking platform, and ISDN network capabilities.

orthAgogue: an agile tool for the rapid prediction of orthology relations.

PubMed

Ekseth, Ole Kristian; Kuiper, Martin; Mironov, Vladimir

2014-03-01

The comparison of genes and gene products across species depends on high-quality tools to determine the relationships between gene or protein sequences from various species. Although some excellent applications are available and widely used, their performance leaves room for improvement. We developed orthAgogue: a multithreaded C application for high-speed estimation of homology relations in massive datasets, operated via a flexible and easy command-line interface. The orthAgogue software is distributed under the GNU license. The source code and binaries compiled for Linux are available at https://code.google.com/p/orthagogue/.

CFDP Evolutions and File Based Operations

NASA Astrophysics Data System (ADS)

Valverde, Alberto; Taylor, Chris; Magistrati, Giorgio; Maiorano, Elena; Colombo, Cyril; Haddow, Colin

2015-09-01

The complexity of the scientific ESA missions in terms of data handling requirements has been steadily increasing in the last years. The availability of high speed telemetry links to ground, the increase on the data storage capacity, as well as the processing performance of the spacecraft avionics have enabled this process. Nowadays, it is common to find missions with hundreds of gigabytes of daily on-board generated data, with terabytes of on-board mass memories and with downlinks of several hundreds of megabits per second. This technological trends push an upgrade on the spacecraft data handling and operation concept, smarter solutions are needed to sustain such high data rates and volumes, while improving the on-board autonomy and easing operations. This paper describes the different activities carried out to adapt to the new data handling scenario. It contains an analysis of the proposed operations concept for file-based spacecrafts, including the updates on the PUS and CFDP standards.

Air transportation energy efficiency - Alternatives and implications

NASA Technical Reports Server (NTRS)

Williams, L. J.

1976-01-01

Results from recent studies of air transportation energy efficiency alternatives are discussed, along with some of the implications of these alternatives. The fuel-saving alternatives considered include aircraft operation, aircraft modification, derivative aircraft, and new aircraft. In the near-term, energy efficiency improvements should be possible through small improvements in fuel-saving flight procedures, higher density seating, and higher load factors. Additional small near-term improvements could be obtained through aircraft modifications, such as the relatively inexpensive drag reduction modifications. Derivatives of existing aircraft could meet the requirements for new aircraft and provide energy improvements until advanced technology is available to justify the cost of a completely new design. In order to obtain significant improvements in energy efficiency, new aircraft must truly exploit advanced technology in such areas as aerodynamics, composite structures, active controls, and advanced propulsion.

Microstructural Characterisation and Wear Behaviour of Diamond Composite Materials

PubMed Central

Boland, James N.; Li, Xing S.

2010-01-01

Since the initial research leading to the production of diamond composite materials, there have been several important developments leading to significant improvements in the properties of these superhard composite materials. Apart from the fact that diamonds, whether originating from natural resources or synthesised commercially, are the hardest and most wear-resistant materials commonly available, there are other mechanical properties that limit their industrial application. These include the low fracture toughness and low impact strength of diamond. By incorporating a range of binder phases into the sintering production process of these composites, these critically important properties have been radically improved. These new composites can withstand much higher operating temperatures without markedly reducing their strength and wear resistance. Further innovative steps are now being made to improve the properties of diamond composites by reducing grain and particle sizes into the nano range. This review will cover recent developments in diamond composite materials with special emphasis on microstructural characterisation. The results of such studies should assist in the design of new, innovative diamond tools as well as leading to radical improvements in the productivity of cutting, drilling and sawing operations in the exploration, mining, civil construction and manufacturing industries.

Ground Support Network for Operational Radio Occultation Missions

NASA Astrophysics Data System (ADS)

Zandbergen, R.; Enderle, W.; Marquardt, C.; Wollenweber, F.

2012-04-01

The EUMETSAT/ESA Metop/EPS GRAS radio occultation mission stands out for its operational nature. From the beginning, EUMETSAT has decided to rely on an operational system for provision of the auxiliary GPS products that are needed in the occultation processing. This system is the GRAS Ground Support Network (GSN), operated in the Navigation Facility of ESOC in Darmstadt, which was first presented at EGU in 2008. The GRAS GSN is driven primarily by timeliness, availability and accuracy requirements. The performance of the GSN, measured on a monthly basis, has not only consistently met these requirements since the start of its operations, but has also been improved through several system enhancements. Currently, an additional service is being delivered on an experimental basis, consisting of a near-real time Navigation Bit Stream product, which will allow the processing of open-loop data, further increasing the scientific return of the GRAS instrument, or any other radio occultation mission using this data. This paper will present the GRAS GSN in its current configuration, and demonstrate its excellent performance in terms of accuracy, availability and timeliness. The application of the bit stream data will be shown. Some future evolution perspectives of the GRAS GSN will also be addressed. It will be demonstrated that the GRAS GSN has the potential of serving also other present and future radio occultation missions.

Software implementation of the SKIPSM paradigm under PIP

NASA Astrophysics Data System (ADS)

Hack, Ralf; Waltz, Frederick M.; Batchelor, Bruce G.

1997-09-01

SKIPSM (separated-kernel image processing using finite state machines) is a technique for implementing large-kernel binary- morphology operators and many other operations. While earlier papers on SKIPSM concentrated mainly on implementations using pipelined hardware, there is considerable scope for achieving major speed improvements in software systems. Using identical control software, one-pass binary erosion and dilation structuring elements (SEs) ranging from the trivial (3 by 3) to the gigantic (51 by 51, or even larger), are readily available. Processing speed is independent of the size of the SE, making the SKIPSM approach practical for work with very large SEs on ordinary desktop computers. PIP (prolog image processing) is an interactive machine vision prototyping environment developed at the University of Wales Cardiff. It consists of a large number of image processing operators embedded within the standard AI language Prolog. This paper describes the SKIPSM implementation of binary morphology operators within PIP. A large set of binary erosion and dilation operations (circles, squares, diamonds, octagons, etc.) is available to the user through a command-line driven dialogue, via pull-down menus, or incorporated into standard (Prolog) programs. Little has been done thus far to optimize speed on this first software implementation of SKIPSM. Nevertheless, the results are impressive. The paper describes sample applications and presents timing figures. Readers have the opportunity to try out these operations on demonstration software written by the University of Wales, or via their WWW home page at http://bruce.cs.cf.ac.uk/bruce/index.html .

[Microsurgical treatment of brachial plexus injuries].

PubMed

Päzolt, H J

1986-01-01

Injuries of the brachial plexus are found to occur primarily to juvenile patients as a consequence of motorcycle accidents. While it is a severe injury, its prognosis has been substantively improved by the availability of microsurgical treatment, using long nerve transplants. Further improvement of results will be possible by early operation, a desirable objective. 44 patients with brachial palsy received treatment, including surgery in 41 cases. An account is given in this paper of intraoperative findings, surgical techniques, and results from follow-up checks. The need is underlined for long-term intensive after-care for the purpose of occupational reintegration.

Absorption heat pump system

DOEpatents

Grossman, Gershon; Perez-Blanco, Horacio

1984-01-01

An improvement in an absorption heat pump cycle is obtained by adding adiabatic absorption and desorption steps to the absorber and desorber of the system. The adiabatic processes make it possible to obtain the highest temperature in the absorber before any heat is removed from it and the lowest temperature in the desorber before heat is added to it, allowing for efficient utilization of the thermodynamic availability of the heat supply stream. The improved system can operate with a larger difference between high and low working fluid concentrations, less circulation losses, and more efficient heat exchange than a conventional system.

Program of operation for the National Water Data Exchange (NAWDEX)

USGS Publications Warehouse

Edwards, Melvin D.

1977-01-01

The National Water Data Exchange (NAWDEX) has been established as a nationwide program directed at improving access to water and water-related data and disseminating information about the availability of these data throughout the entire water-resources community. NAWDEX is composed of a confederation of water-oriented organizations working together to facilitate the exchange of data and to improve the technology of data handling and transfer. This report is intended to provide guidelines to assure that all member organizations participate equally and that a climate of cooperation and open communication is established among participating members. (Woodard-USGS)

Absorption-heat-pump system

DOEpatents

Grossman, G.; Perez-Blanco, H.

1983-06-16

An improvement in an absorption heat pump cycle is obtained by adding adiabatic absorption and desorption steps to the absorber and desorber of the system. The adiabatic processes make it possible to obtain the highest temperature in the absorber before any heat is removed from it and the lowest temperature in the desorber before heat is added to it, allowing for efficient utilization of the thermodynamic availability of the heat supply stream. The improved system can operate with a larger difference between high and low working fluid concentrations, less circulation losses, and more efficient heat exchange than a conventional system.

Can advanced technology improve future commuter aircraft

NASA Technical Reports Server (NTRS)

Williams, L. J.; Snow, D. B.

1981-01-01

The short-haul service abandoned by the trunk and local airlines is being picked up by the commuter airlines using small turboprop-powered aircraft. Most of the existing small transport aircraft currently available represent a relatively old technology level. However, several manufacturers have initiated the development of new or improved commuter transport aircraft. These aircraft are relatively conservative in terms of technology. An examination is conducted of advanced technology to identify those technologies that, if developed, would provide the largest improvements for future generations of these aircraft. Attention is given to commuter aircraft operating cost, aerodynamics, structures and materials, propulsion, aircraft systems, and technology integration. It is found that advanced technology can improve future commuter aircraft and that the largest of these improvements will come from the synergistic combination of technological advances in all of the aircraft disciplines. The most important goals are related to improved fuel efficiency and increased aircraft productivity.

Sentinel-3 SAR Altimetry over Coastal and Open Ocean: performance assessment and improved retrieval methods in the ESA SCOOP Project.

NASA Astrophysics Data System (ADS)

Benveniste, J.; Cotton, D.; Moreau, T.; Raynal, M.; Varona, E.; Cipollini, P.; Cancet, M.; Martin, F.; Fenoglio-Marc, L.; Naeije, M.; Fernandes, J.; Lazaro, C.; Restano, M.; Ambrózio, A.

2017-12-01

The ESA Sentinel-3 satellite, launched in February 2016 as a part of the Copernicus programme, is the second satellite to operate a SAR mode altimeter. The Sentinel 3 Synthetic Aperture Radar Altimeter (SRAL) is based on the heritage from Cryosat-2, but this time complemented by a Microwave Radiometer (MWR) to provide a wet troposphere correction, and operating at Ku and C-Bands to provide an accurate along-track ionospheric correction. The SRAL is operated in SAR mode over the whole ocean and promises increased performance w.r.t. conventional altimetry. SCOOP (SAR Altimetry Coastal & Open Ocean Performance) is a project funded under the ESA SEOM (Scientific Exploitation of Operational Missions) Programme Element, started in September 2015, to characterise the expected performance of Sentinel-3 SRAL SAR mode altimeter products, in the coastal zone and open-ocean, and then to develop and evaluate enhancements to the baseline processing scheme in terms of improvements to ocean measurements. There is also a work package to develop and evaluate an improved Wet Troposphere correction for Sentinel-3, based on the measurements from the on-board MWR, further enhanced mostly in the coastal and polar regions using third party data, and provide recommendations for use. In this presentation we present results from the SCOOP project that demonstrate the excellent performance of SRAL in terms of measurement precision, and we illustrate the development and testing of new processing approaches designed specifically to improve performance close to the coast. The SCOOP test data sets and relevant documentation are available to external researchers on application to the project team. At the end of the project recommendations for further developments and implementations will be provided through a scientific roadmap.

Defining Gas Turbine Engine Performance Requirements for the Large Civil TiltRotor (LCTR2)

NASA Technical Reports Server (NTRS)

Snyder, Christopher A.

2013-01-01

Defining specific engine requirements is a critical part of identifying technologies and operational models for potential future rotary wing vehicles. NASA's Fundamental Aeronautics Program, Subsonic Rotary Wing Project has identified the Large Civil TiltRotor (LCTR) as the configuration to best meet technology goals. This notional vehicle concept has evolved with more clearly defined mission and operational requirements to the LCTR-iteration 2 (LCTR2). This paper reports on efforts to further review and refine the LCTR2 analyses to ascertain specific engine requirements and propulsion sizing criteria. The baseline mission and other design or operational requirements are reviewed. Analysis tools are described to help understand their interactions and underlying assumptions. Various design and operational conditions are presented and explained for their contribution to defining operational and engine requirements. These identified engine requirements are discussed to suggest which are most critical to the engine sizing and operation. The most-critical engine requirements are compared to in-house NASA engine simulations to try to ascertain which operational requirements define engine requirements versus points within the available engine operational capability. Finally, results are summarized with suggestions for future efforts to improve analysis capabilities, and better define and refine mission and operational requirements.

GOES-16 Space Weather Data Availability and Applications

NASA Astrophysics Data System (ADS)

Tilton, M.; Rowland, W. F.; Codrescu, S.; Seaton, D. B.; Redmon, R. J.; Hsu, V.

2017-12-01

In November 2016, NOAA launched the first in the "R" series of Geostationary Operational Environmental Satellites, GOES-16. Compared to its GOES predecessors, the GOES-R series satellites provide improved in situ measurements of charged particles, higher cadence magnetic field measurements, and enhanced remote sensing of the sun through ultraviolet (UV) imagery and X-ray/UV irradiance. GOES-16 space weather instruments will nominally reach provisional status near the beginning of 2018. After this milestone has been achieved, NOAA's National Centers for Environmental Information (NCEI) will provide archive access to GOES-16 space weather data. This presentation will describe the status of the space weather instruments, including available products and their applicability for forecasters, modelers, academics, spacecraft operators, and other users. It will discuss the available access systems for all levels of data-raw telemetry (Level 0), science measurements in high resolution (L1b), and higher-level (L2+) products developed by NCEI scientists. Finally, it will cover NCEI's efforts to promote space weather awareness through data visualization tools and image dissemination via the Helioviewer project.

A system for the management, display and integration of pre-hospital healthcare activity in the deployed environment.

PubMed

Grant, Simon; Wheatley, R J

2014-12-01

To create and implement a system through which pre-hospital healthcare activity across an entire operational theatre could be made available in real-time to support healthcare delivery, governance and assurance activity. An IT-based system was created that could display, manage and integrate the pre-hospital healthcare activity on Op HERRICK 18. The system was based on the Defence Medical Services Common Assurance Framework and run through Microsoft Office SharePoint. Pre-hospital healthcare activity was made available and visible across an operational theatre. This supported delivery, assurance and governance at any time. Activity from each medical facility could be integrated and display automatically improving theatre wide situational awareness. The availability of information resulted in a shift towards a more continuous process of assurance and governance rather than reliance on inherently threatening and increasingly intermittent inspection regimes. The ability to review healthcare activity remotely at anytime significantly improves the validity of assurance possible for a deployed force. Governance activity can be more responsive and less reliant on the fixed timescale and datasets of reports from outlying medical facilities. However, assurance and governance authorities must not allow such a wealth of information to impact local leadership and innovation through a perception of, or actual, micro-management. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Performance after rotator cuff tear and operative treatment: a case-control study of major league baseball pitchers.

PubMed

Namdari, Surena; Baldwin, Keith; Ahn, Albert; Huffman, G Russell; Sennett, Brian J

2011-01-01

Little is known about pitching performance or lack of it among Major League Baseball (MLB) pitchers who undergo operative treatment of rotator cuff tears. To assess pitching performance outcomes in MLB players who needed operative treatment of rotator cuff tears and to compare performance in these athletes with that in a control group of MLB players. Case-control study. Publicly available player profiles, press releases, and team injury reports. Thirty-three MLB pitchers with documented surgery to treat rotator cuff tears and 117 control pitchers who did not have documented rotator cuff tears were identified. Major League Baseball pitching attrition and performance variables. Players who underwent rotator cuff surgery were no more likely not to play than control players. Performance variables of players who underwent surgery improved after surgery but never returned to baseline preoperative status. Players who needed rotator cuff surgery typically were more experienced and had better earned run averages than control players. Pitchers who had symptomatic rotator cuff tears that necessitated operative treatment tended to decline gradually in performance leading up to their operations and to improve gradually over the next 3 seasons. In contrast to what we expected, they did not have a greater attrition rate than their control counterparts; however, their performances did not return to preoperative levels over the course of the study.

High Temperature Transparent Furnace Development

NASA Technical Reports Server (NTRS)

Bates, Stephen C.

1997-01-01

This report describes the use of novel techniques for heat containment that could be used to build a high temperature transparent furnace. The primary objective of the work was to experimentally demonstrate transparent furnace operation at 1200 C. Secondary objectives were to understand furnace operation and furnace component specification to enable the design and construction of a low power prototype furnace for delivery to NASA in a follow-up project. The basic approach of the research was to couple high temperature component design with simple concept demonstration experiments that modify a commercially available transparent furnace rated at lower temperature. A detailed energy balance of the operating transparent furnace was performed, calculating heat losses through the furnace components as a result of conduction, radiation, and convection. The transparent furnace shells and furnace components were redesigned to permit furnace operation at at least 1200 C. Techniques were developed that are expected to lead to significantly improved heat containment compared with current transparent furnaces. The design of a thermal profile in a multizone high temperature transparent furnace design was also addressed. Experiments were performed to verify the energy balance analysis, to demonstrate some of the major furnace improvement techniques developed, and to demonstrate the overall feasibility of a high temperature transparent furnace. The important objective of the research was achieved: to demonstrate the feasibility of operating a transparent furnace at 1200 C.

A review of recent advances in data analytics for post-operative patient deterioration detection.

PubMed

Petit, Clemence; Bezemer, Rick; Atallah, Louis

2018-06-01

Most deaths occurring due to a surgical intervention happen postoperatively rather than during surgery. The current standard of care in many hospitals cannot fully cope with detecting and addressing post-surgical deterioration in time. For millions of patients, this deterioration is left unnoticed, leading to increased mortality and morbidity. Postoperative deterioration detection currently relies on general scores that are not fully able to cater for the complex post-operative physiology of surgical patients. In the last decade however, advanced risk and warning scoring techniques have started to show encouraging results in terms of using the large amount of data available peri-operatively to improve postoperative deterioration detection. Relevant literature has been carefully surveyed to provide a summary of the most promising approaches as well as how they have been deployed in the perioperative domain. This work also aims to highlight the opportunities that lie in personalizing the models developed for patient deterioration for these particular post-surgical patients and make the output more actionable. The integration of pre- and intra-operative data, e.g. comorbidities, vitals, lab data, and information about the procedure performed, in post-operative early warning algorithms would lead to more contextualized, personalized, and adaptive patient modelling. This, combined with careful integration in the clinical workflow, would result in improved clinical decision support and better post-surgical care outcomes.

Mobile Centers For Secondary Power Distribution

NASA Technical Reports Server (NTRS)

Mears, Robert L.

1990-01-01

Concept for distribution of 60-Hz ac power in large building devoted to assembly and testing of equipment improves safety, reduces number of outlets and lengthy cables, and readily accommodates frequent changes in operations and configuration. Power from floor recess fed via unobtrusive cable to portable power management center. A cart containing variety of outlets and circuit breakers, wheeled to convenient location near equipment to be assembled or tested. Power distribution system presents larger range of operational configurations than fixed location. Meets tighter standards to feed computers and delicate instruments. Industrial-grade power suitable for power tools and other hardware. Three-phase and single-phase outlets available from each.

Final environmental assessment: Sacramento Energy Service Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-03-01

The Sacramento Area Office (SAO) of the Western Area Power Administration (Western) needs to increase the security of operations, to eliminate overcrowding at the current leased location of the existing facilities, to provide for future growth, to improve efficiency, and to reduce operating costs. The proposed action is to construct an approximate 40,000-square foot building and adjacent parking lot with a Solar Powered Electric Vehicle Charging Station installed to promote use of energy efficient transportation. As funding becomes available and technology develops, additional innovative energy-efficient measures will be incorporated into the building. For example the proposed construction of the Solarmore » Powered Electric Vehicle Charging.« less

The Model VI transmission fluorimeter for the determination of uranium

USGS Publications Warehouse

Kinser, Charles Alvin

1954-01-01

An improved transmission fluorimeter (Model VI) for use in the determination of uranium consists of a line-operated, low-voltage d-c supply, powering a small 3-watt ultraviolet lamp as a source of long wavelength ultraviolet radiation; a Model V phototube housing and. fluorimeter head containing the sample holder, shutter, and primary and secondary filters; an end-window multiplier phototube powered by a stable, commercially available high-voltage supply; and an electronic microammeter for measuring the output current from the photomultiplier tube. The instrument has excellent electrical stability and operates over a wide range of sensitivity. Its versatility makes it useful for both routine and research work.

Enhancing BEM simulations of a stalled wind turbine using a 3D correction model

NASA Astrophysics Data System (ADS)

Bangga, Galih; Hutomo, Go; Syawitri, Taurista; Kusumadewi, Tri; Oktavia, Winda; Sabila, Ahmad; Setiadi, Herlambang; Faisal, Muhamad; Hendranata, Yongki; Lastomo, Dwi; Putra, Louis; Kristiadi, Stefanus; Bumi, Ilmi

2018-03-01

Nowadays wind turbine rotors are usually employed with pitch control mechanisms to avoid deep stall conditions. Despite that, wind turbines often operate under pitch fault situation causing massive flow separation to occur. Pure Blade Element Momentum (BEM) approaches are not designed for this situation and inaccurate load predictions are already expected. In the present studies, BEM predictions are improved through the inclusion of a stall delay model for a wind turbine rotor operating under pitch fault situation of -2.3° towards stall. The accuracy of the stall delay model is assessed by comparing the results with available Computational Fluid Dynamics (CFD) simulations data.

Analysing the performance of personal computers based on Intel microprocessors for sequence aligning bioinformatics applications.

PubMed

Nair, Pradeep S; John, Eugene B

2007-01-01

Aligning specific sequences against a very large number of other sequences is a central aspect of bioinformatics. With the widespread availability of personal computers in biology laboratories, sequence alignment is now often performed locally. This makes it necessary to analyse the performance of personal computers for sequence aligning bioinformatics benchmarks. In this paper, we analyse the performance of a personal computer for the popular BLAST and FASTA sequence alignment suites. Results indicate that these benchmarks have a large number of recurring operations and use memory operations extensively. It seems that the performance can be improved with a bigger L1-cache.

Portable home hemodialysis for kidney failure.

PubMed

Scott, A

2007-11-01

(1) Home hemodialysis has been in limited use in Canada for some time. Newer, portable hemodialysis machines that are easier for patients to operate may encourage the uptake of this technology. (2) One portable system is already available in the US. The NxStage System One hemodialysis machine operates on standard electric current, does not require plumbing or specialized disinfection, and is small enough for patients to travel with. (3) It is not yet clear whether the use of the NxStage system improves long-term survival and quality of life. (4) Home hemodialysis is less costly than conventional in-centre programs, but it is unknown whether these savings extend to portable devices.

Improving the efficiency of optical coherence tomography by using the non-ideal behaviour of a polarising beam splitter.

PubMed

Lippok, Norman; Nielsen, Poul; Vanholsbeeck, Frédérique

2011-04-11

We present a new way of improving the efficiency of optical coherence tomography by using the polarisation crosstalk of a polarising beam splitter to direct most of the available source optical power to the sample. The use of a quarter wave plate in both the reference and the sample arms allows most of the sample power to be directed to the detector while adjusting the reference arm to ensure noise optimised operation. As a result, the sensitivity of such a system can be improved by 6 dB, or alternatively the acquisition time can be improved by a factor of 4 for shot noise limited performance,compared to a traditional OCT configuration using a 50/50 beam splitter. © 2011 Optical Society of America

Validation of exposure assessment and assessment of recruitment methods for a prospective cohort study of mobile phone users (COSMOS) in Finland: a pilot study

PubMed Central

2011-01-01

Background The aim of the study was to evaluate the agreement between self-reported and operator-derived estimates of call time based on a three-month monitoring period, as well as the consistency of mobile phone use over time. Alternative approaches to improve participation in a cohort study of mobile phone users were also compared. Methods A total of 5,400 subjects were identified from network operators' subscriber databases for recruitment to the pilot study. Operator and questionnaire data were used to quantify mobile phone use. Operator data were available for a subset of the subjects for a three-month period in three consecutive years. We also evaluated the effect of the length of the questionnaire and one- or two-phase recruitment on participation. Results The average response rate for both questionnaires and recruitment procedures was 12%. The response rate was not affected by the length of the questionnaire or the recruitment method. Operator data were available for 83% of the participants for 2007, the first study year. The agreement between self-reported and operator-derived call times decreased with the level of use among intermediate and heavy mobile phone users. During 2007-2009, mobile phone use increased fairly constantly over time. Conclusions The agreement between self-reported mobile phone use and operator databases was moderate and overestimation of the call time by participants was common. A prospective cohort study would be feasible in Finland, although the potentially low participation rate would increase the resources required for recruitment. PMID:21385407

Methodology for the systems engineering process. Volume 3: Operational availability

NASA Technical Reports Server (NTRS)

Nelson, J. H.

1972-01-01

A detailed description and explanation of the operational availability parameter is presented. The fundamental mathematical basis for operational availability is developed, and its relationship to a system's overall performance effectiveness is illustrated within the context of identifying specific availability requirements. Thus, in attempting to provide a general methodology for treating both hypothetical and existing availability requirements, the concept of an availability state, in conjunction with the more conventional probability-time capability, is investigated. In this respect, emphasis is focused upon a balanced analytical and pragmatic treatment of operational availability within the system design process. For example, several applications of operational availability to typical aerospace systems are presented, encompassing the techniques of Monte Carlo simulation, system performance availability trade-off studies, analytical modeling of specific scenarios, as well as the determination of launch-on-time probabilities. Finally, an extensive bibliography is provided to indicate further levels of depth and detail of the operational availability parameter.

Training on an inexpensive tablet-based device is equally effective as on a standard laparoscopic box trainer

PubMed Central

Montanari, Eliana; Schwameis, Richard; Louridas, Marisa; Göbl, Christian; Kuessel, Lorenz; Polterauer, Stephan; Husslein, Heinrich

2016-01-01

Abstract Background: The aim of the study was to assess whether an inexpensive tablet-based box trainer (TBT) is at least equally effective compared with a standard box trainer (SBT) to learn basic laparoscopic skills (BLS). BLS training outside the operating room has been shown to be beneficial for surgical residency. However, simulation trainers are expensive and are not consistently available in all training centers. Therefore, TBT and other homemade box trainers were developed. Methods: Medical students were randomized to either a TBT or an SBT and trained 4 fundamentals of laparoscopic surgery (FLS) tasks for 1 hour twice a week for 4 weeks. A baseline test before the training period and a posttraining test were performed. All students then completed a questionnaire to assess their assigned box trainer. The primary outcome measure was the improvement in total test scores. Improvement in the scores for the 4 individual FLS tasks was chosen as a secondary outcome measure. Results: Thirty-two medical students were recruited. Baseline test scores did not differ significantly between the groups. BLS improved significantly in both groups for the total score and for all 4 tasks separately. Participants in the TBT group showed a greater improvement of total scores than those in the SBT group, although this did not reach statistical significance; noninferiority of the TBT compared with the SBT concerning the improvement of total scores could be demonstrated. Regarding the individual FLS tasks, noninferiority of the TBT could be shown for the pattern cutting and the suturing with intracorporeal knot-tying task. The acceptance of the TBT by the trainees was very good. Conclusion: Learning BLS on a homemade TBT is at least equally effective as on an SBT, with the advantage of being very cost saving. Therefore, this readily available box trainer may be used as an effective, flexible training device outside the operating room to improve accessibility to simulation training. PMID:27684813

Two simple techniques for the safe Sarcoptes collection and individual mite DNA extraction.

PubMed

Soglia, Dominga; Rambozzi, Luisa; Maione, Sandra; Spalenza, Veronica; Sartore, Stefano; Alasaad, Samer; Sacchi, Paola; Rossi, Luca

2009-10-01

Availability of mites is a recognized limiting factor of biological and genetic investigations of the genus Sarcoptes. Current methods of deoxyribonucleic acid (DNA) extraction from individual mites also need substantial improvement in efficiency and operator friendliness. We have first developed a technique for efficient and safe extraction of living mites from scabietic skin samples (crusts or deep skin scrapings). Its core device is a large plastic syringe connected with a 1.5-ml Eppendorf tube. The source material is introduced in the syringe and the device in a shoe box with the tip half of the tube emerging. Mites migrate towards a heat source during a minimum of 36 h. Then, the tube is detached and the mites utilized without risks for the operators. A second technique allows operator-friendly manipulation of individual mites for DNA extraction. Fixed mites are isolated by adhesion to a small strip of polyvinyl chloride (PVC) adhesive tape operated with tweezers. Then, mite and strip are plunged in the lyses buffer and the sample twice submitted to thermal shock for disruption of the chitinous exoskeleton. Data show that the tape does not interfere with successive DNA extraction with a commercial kit. The corresponding protocol, that we briefly name "PVC adhesive tape + thermal shock + kit DNA extraction," compares favorably with the available ones.

The Global Communication Infrastructure of the International Monitoring System

NASA Astrophysics Data System (ADS)

Lastowka, L.; Gray, A.; Anichenko, A.

2007-05-01

The Global Communications Infrastructure (GCI) employs 6 satellites in various frequency bands distributed around the globe. Communications with the PTS (Provisional Technical Secretariat) in Vienna, Austria are achieved through VSAT technologies, international leased data circuits and Virtual Private Network (VPN) connections over the Internet. To date, 210 independent VSAT circuits have been connected to Vienna as well as special circuits connecting to the Antarctic and to independent sub-networks. Data volumes from all technologies currently reach 8 Gigabytes per day. The first level of support and a 24/7 help desk remains with the GCI contractor, but performance is monitored actively by the PTS/GCI operations team. GCI operations are being progressively introduced into the PTS operations centre. An Operations centre fully integrated with the GCI segment of the IMS network will ensure a more focused response to incidents and will maximize the availability of the IMS network. Existing trouble tickets systems are being merged to ensure the commission manages GCI incidents in the context of the IMS as a whole. A focus on a single source of data for GCI network performance has enabled reporting systems to be developed which allow for improved and automated reports. The contracted availability for each individual virtual circuit is 99.5% and this performance is regularly reviewed on a monthly basis

Description and evaluation of operative deformity correction in calcium-deficiency rickets in Kaduna, northern Nigeria.

PubMed

Wesselsky, Viktor; Kitz, Christa; Jakob, Franz; Eulert, Jochen; Raab, Peter

2016-04-01

Rickets is a recurrent disease worldwide, especially in countries with limited resources (Nield et al Am Fam Physician 74(4):619-626, 2006; Thacher et al Ann Trop Paediatr 26(1):1-16, 2006). Medical therapy including orally administered calcium substitution is shown to improve a patients clinical symptoms and positively impact bone deformities, especially in the lower extremity. Even though orthopaedic intervention is necessary in a significant percentage of patients, few reports exist about operative deformity correction in patients wtih rickets. We describe our concept of operative treatment by single-stage, three-dimensional closing-wedge osteotomies on 45 deformed legs in 27 patients from the rural area of Kaduna, North Nigeria, with calcium-deficiency rickets and evaluate the early results in a 1.5-year follow-up. We found a significant improvement in parameters of quality of life, functionality, clinical and radiological angulation and angles following the definition of Paley et al., with a complication rate of 4 % under 88 osteotomies (Paley et al Orthop Clin North Am 25(3):425-65, 1994). The described operative therapy shows to be sufficient and with satisfactory results in correcting rickets-related leg deformities under rural circumstances with low availability of medical resources.

Recent progress in millimeter-wave sensor system capabilities for enhanced (synthetic) vision

NASA Astrophysics Data System (ADS)

Hellemann, Karlheinz; Zachai, Reinhard

1999-07-01

Weather- and daylight independent operation of modern traffic systems is strongly required for an optimized and economic availability. Mainly helicopters, small aircraft and military transport aircraft operating frequently close to the ground have a need for effective and cost-effective Enhanced Vision sensors. The technical progress in sensor technology and processing speed offer today the possibility for new concepts to be realized. Derived from this background the paper reports on the improvements which are under development within the HiVision program at DaimlerChrysler Aerospace. A sensor demonstrator based on FMCW radar technology with high information update-rate and operating in the mm-wave band, has been up-graded to improve performance and fitted to fly on an experimental base. The results achieved so far demonstrate the capability to produce a weather independent enhanced vision. In addition the demonstrator has been tested on board a high- speed ferry at the Baltic sea, because fast vessels have a similar need for weather-independent operation and anti- collision measures. In the future one sensor type may serve both 'worlds' and help ease and save traffic. The described demonstrator fills up the technology gap between optical sensors (Infrared) and standard pulse radars with its specific features such as high speed scanning and weather penetration with the additional benefit of cost-effectiveness.

Informatics in radiology: use of a C-arm fluoroscopy simulator to support training in intraoperative radiography.

PubMed

Bott, Oliver Johannes; Dresing, Klaus; Wagner, Markus; Raab, Björn-Werner; Teistler, Michael

2011-01-01

Mobile image intensifier systems (C-arms) are used frequently in orthopedic and reconstructive surgery, especially in trauma and emergency settings, but image quality and radiation exposure levels may vary widely, depending on the extent of the C-arm operator's knowledge and experience. Current training programs consist mainly of theoretical instruction in C-arm operation, the physical foundations of radiography, and radiation avoidance, and are largely lacking in hands-on application. A computer-based simulation program such as that tested by the authors may be one way to improve the effectiveness of C-arm training. In computer simulations of various scenarios commonly encountered in the operating room, trainees using the virtX program interact with three-dimensional models to test their knowledge base and improve their skill levels. Radiographs showing the simulated patient anatomy and surgical implants are "reconstructed" from data computed on the basis of the trainee's positioning of models of a C-arm, patient, and table, and are displayed in real time on the desktop monitor. Trainee performance is signaled in real time by color graphics in several control panels and, on completion of the exercise, is compared in detail with the performance of an expert operator. Testing of this computer-based training program in continuing medical education courses for operating room personnel showed an improvement in the overall understanding of underlying principles of intraoperative radiography performed with a C-arm, with resultant higher image quality, lower overall radiation exposure, and greater time efficiency. Supplemental material available at http://radiographics.rsna.org/lookup/suppl/doi:10.1148/rg.313105125/-/DC1. Copyright © RSNA, 2011.

Improving surgeon utilization in an orthopedic department using simulation modeling

PubMed Central

Simwita, Yusta W; Helgheim, Berit I

2016-01-01

Purpose Worldwide more than two billion people lack appropriate access to surgical services due to mismatch between existing human resource and patient demands. Improving utilization of existing workforce capacity can reduce the existing gap between surgical demand and available workforce capacity. In this paper, the authors use discrete event simulation to explore the care process at an orthopedic department. Our main focus is improving utilization of surgeons while minimizing patient wait time. Methods The authors collaborated with orthopedic department personnel to map the current operations of orthopedic care process in order to identify factors that influence poor surgeons utilization and high patient waiting time. The authors used an observational approach to collect data. The developed model was validated by comparing the simulation output with the actual patient data that were collected from the studied orthopedic care process. The authors developed a proposal scenario to show how to improve surgeon utilization. Results The simulation results showed that if ancillary services could be performed before the start of clinic examination services, the orthopedic care process could be highly improved. That is, improved surgeon utilization and reduced patient waiting time. Simulation results demonstrate that with improved surgeon utilizations, up to 55% increase of future demand can be accommodated without patients reaching current waiting time at this clinic, thus, improving patient access to health care services. Conclusion This study shows how simulation modeling can be used to improve health care processes. This study was limited to a single care process; however the findings can be applied to improve other orthopedic care process with similar operational characteristics. PMID:29355193

Landsat data availability from the EROS Data Center and status of future plans

USGS Publications Warehouse

Pohl, Russell A.; Metz, G.G.

1977-01-01

The Department of Interior's EROS Data Center, managed by the U.S. Geological Survey, was established in 1972, in Sioux Falls, South Dakota, to serve as a principal dissemination facility for Landsat and other remotely Sensed data. Through the middle of 1977, the Center has supplied approximately 1.7 million copies of images from the more than 5 million images of the Earth's surface archived at the Center. Landsat accounted for half of these images plus approximately 5,800 computer-compatible tapes of Landsat data were also supplied to users. New methods for processing data products to make them more useful are being developed, and new accession aids for determining data availability are being placed in operation. The Center also provides assistance and training to resource specialists and land managers in the use of Landsat and other remotely sensed data. A Data Analysis Laboratory is operated at the Center to provide both digital and analog multispectral/multitemporal image analysis capabilities in support of the training and assistance programs. In addition to conventionally processed data products, radiometrically enhanced Landsat imagery are now available from the Center in limited quantities. In mid-1978, the Center will convert to an all-digital processing system for Landsat data that will provide improved products for user analysis in production quantities. The Department of Interior and NASA are currently studying concepts that use communication satellites to relay Landsat data between U.S. ground stations, Goddard Space Flight Center and the EROS Data Center which would improve the timeliness of data availability. The Data Center also works closely with the remote sensing programs and Landsat data receiving and processing facilities being developed in foreign countries.

Influences of Work-Life Support of Officers’ Organizational Commitment and Negative Work-Family Spillover

DTIC Science & Technology

2006-04-01

demands of work and family life is a promising intervention for improving Soldier experiences and increasing retention in the Army. This research...When Soldiers leave military service, the loss decreases the personnel available for operational missions. Consequently, a continued concern of the ...Army is to understand processes leading to Soldier retention and attrition. Given the large body of research showing that employees’ organizational

Banking: shop and compare.

PubMed

O'Brien, Jennifer A; DeJarnette, Sherry

2014-01-01

There are many reasons to take a critical look at the practice's banking relationship(s)--technology advancements, security measures, improvements in available services, recent banking enhancements designed specifically for medical practices, the impact of the financial crisis on bank ratings and stability, changing practice needs, opportunities for operational automation at the practice--and it is just simply smart to periodically evaluate and compare the features, pricing, and potential savings offered by vendors.

Deployable Fuel Cell Power Generator - Multi-Fuel Processor

DTIC Science & Technology

2009-02-01

and the system operating pressure, while the separation efficiency depends on the evaporator design. Desulfurizer – A flow-through gas -solid or gas ...meeting the Executive Order (EO) 13423 and the Energy Policy Act of 2005 to improve energy efficiency and reduce greenhouse gas emissions 3 percent...use available fuel such as natural gas (methane) or propane. The ability to reform multitude of fuels can accelerate the introduction of more

National Search and Rescue Manual. Addendum.

DTIC Science & Technology

1979-08-01

are inherent in the aerial delivery of a. Disastrous consequences can result from equipment. The degree of risk depends the dropping of equipment...presented, it isthe risk of the operation and the fact that the desirable to remove all civilians from the dis- action is undertaken at his request... Environmental data available including insight afforded. Such a study may provide sea current, wind and visibility; these data clues for improving our SAR

Software Application Profile: Opal and Mica: open-source software solutions for epidemiological data management, harmonization and dissemination.

PubMed

Doiron, Dany; Marcon, Yannick; Fortier, Isabel; Burton, Paul; Ferretti, Vincent

2017-10-01

Improving the dissemination of information on existing epidemiological studies and facilitating the interoperability of study databases are essential to maximizing the use of resources and accelerating improvements in health. To address this, Maelstrom Research proposes Opal and Mica, two inter-operable open-source software packages providing out-of-the-box solutions for epidemiological data management, harmonization and dissemination. Opal and Mica are two standalone but inter-operable web applications written in Java, JavaScript and PHP. They provide web services and modern user interfaces to access them. Opal allows users to import, manage, annotate and harmonize study data. Mica is used to build searchable web portals disseminating study and variable metadata. When used conjointly, Mica users can securely query and retrieve summary statistics on geographically dispersed Opal servers in real-time. Integration with the DataSHIELD approach allows conducting more complex federated analyses involving statistical models. Opal and Mica are open-source and freely available at [www.obiba.org] under a General Public License (GPL) version 3, and the metadata models and taxonomies that accompany them are available under a Creative Commons licence. © The Author 2017; all rights reserved. Published by Oxford University Press on behalf of the International Epidemiological Association

Inhalation device options for the management of chronic obstructive pulmonary disease.

PubMed

DePietro, Michael; Gilbert, Ileen; Millette, Lauren A; Riebe, Michael

2018-01-01

Chronic obstructive pulmonary disease (COPD) is characterized by chronic respiratory symptoms and airflow limitation, resulting from abnormalities in the airway and/or damage to the alveoli. Primary care physicians manage the healthcare of a large proportion of patients with COPD. In addition to determining the most appropriate medication regimen, which usually includes inhaled bronchodilators with or without inhaled corticosteroids, physicians are charged with optimizing inhalation device selection to facilitate effective drug delivery and patient adherence. The large variety of inhalation devices currently available present numerous challenges for physicians that include: (1) gaining knowledge of and proficiency with operating different device classes; (2) identifying the most appropriate inhalation device for the patient; and (3) providing the necessary education and training for patients on device use. This review provides an overview of the inhalation device types currently available in the United States for delivery of COPD medications, including information on their successful operation and respective advantages and disadvantages, factors to consider in matching a device to an individual patient, the need for device training for patients and physicians, and guidance for improving treatment adherence. Finally, the review will discuss established and novel tools and technology that may aid physicians in improving education and promoting better adherence to therapy.

Improved water allocation utilizing probabilistic climate forecasts: Short-term water contracts in a risk management framework

NASA Astrophysics Data System (ADS)

Sankarasubramanian, A.; Lall, Upmanu; Souza Filho, Francisco Assis; Sharma, Ashish

2009-11-01

Probabilistic, seasonal to interannual streamflow forecasts are becoming increasingly available as the ability to model climate teleconnections is improving. However, water managers and practitioners have been slow to adopt such products, citing concerns with forecast skill. Essentially, a management risk is perceived in "gambling" with operations using a probabilistic forecast, while a system failure upon following existing operating policies is "protected" by the official rules or guidebook. In the presence of a prescribed system of prior allocation of releases under different storage or water availability conditions, the manager has little incentive to change. Innovation in allocation and operation is hence key to improved risk management using such forecasts. A participatory water allocation process that can effectively use probabilistic forecasts as part of an adaptive management strategy is introduced here. Users can express their demand for water through statements that cover the quantity needed at a particular reliability, the temporal distribution of the "allocation," the associated willingness to pay, and compensation in the event of contract nonperformance. The water manager then assesses feasible allocations using the probabilistic forecast that try to meet these criteria across all users. An iterative process between users and water manager could be used to formalize a set of short-term contracts that represent the resulting prioritized water allocation strategy over the operating period for which the forecast was issued. These contracts can be used to allocate water each year/season beyond long-term contracts that may have precedence. Thus, integrated supply and demand management can be achieved. In this paper, a single period multiuser optimization model that can support such an allocation process is presented. The application of this conceptual model is explored using data for the Jaguaribe Metropolitan Hydro System in Ceara, Brazil. The performance relative to the current allocation process is assessed in the context of whether such a model could support the proposed short-term contract based participatory process. A synthetic forecasting example is also used to explore the relative roles of forecast skill and reservoir storage in this framework.

Aircraft Configuration and Flight Crew Compliance with Procedures While Conducting Flight Deck Based Interval Management (FIM) Operations

NASA Technical Reports Server (NTRS)

Shay, Rick; Swieringa, Kurt A.; Baxley, Brian T.

2012-01-01

Flight deck based Interval Management (FIM) applications using ADS-B are being developed to improve both the safety and capacity of the National Airspace System (NAS). FIM is expected to improve the safety and efficiency of the NAS by giving pilots the technology and procedures to precisely achieve an interval behind the preceding aircraft by a specific point. Concurrently but independently, Optimized Profile Descents (OPD) are being developed to help reduce fuel consumption and noise, however, the range of speeds available when flying an OPD results in a decrease in the delivery precision of aircraft to the runway. This requires the addition of a spacing buffer between aircraft, reducing system throughput. FIM addresses this problem by providing pilots with speed guidance to achieve a precise interval behind another aircraft, even while flying optimized descents. The Interval Management with Spacing to Parallel Dependent Runways (IMSPiDR) human-in-the-loop experiment employed 24 commercial pilots to explore the use of FIM equipment to conduct spacing operations behind two aircraft arriving to parallel runways, while flying an OPD during high-density operations. This paper describes the impact of variations in pilot operations; in particular configuring the aircraft, their compliance with FIM operating procedures, and their response to changes of the FIM speed. An example of the displayed FIM speeds used incorrectly by a pilot is also discussed. Finally, this paper examines the relationship between achieving airline operational goals for individual aircraft and the need for ATC to deliver aircraft to the runway with greater precision. The results show that aircraft can fly an OPD and conduct FIM operations to dependent parallel runways, enabling operational goals to be achieved efficiently while maintaining system throughput.

The knowledge-based framework for a nuclear power plant operator advisor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, D.W.; Hajek, B.K.

1989-01-01

An important facet in the design, development, and evaluation of aids for complex systems is the identification of the tasks performed by the operator. Operator aids utilizing artificial intelligence, or more specifically knowledge-based systems, require identification of these tasks in the context of a knowledge-based framework. In this context, the operator responses to the plant behavior are to monitor and comprehend the state of the plant, identify normal and abnormal plant conditions, diagnose abnormal plant conditions, predict plant response to specific control actions, and select the best available control action, implement a feasible control action, monitor system response to themore » control action, and correct for any inappropriate responses. These tasks have been identified to formulate a knowledge-based framework for an operator advisor under development at Ohio State University that utilizes the generic task methodology proposed by Chandrasekaran. The paper lays the foundation to identify the responses as a knowledge-based set of tasks in accordance with the expected human operator responses during an event. Initial evaluation of the expert system indicates the potential for an operator aid that will improve the operator's ability to respond to both anticipated and unanticipated events.« less

Integrating UF6 Cylinder RF Tracking With Continuous Load Cell Monitoring for Verifying Declared UF6 Feed and Withdrawal Operations Verifying Declared UF6 Feed and Withdrawal Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krichinsky, Alan M; Miller, Paul; Pickett, Chris A

2009-01-01

Oak Ridge National Laboratory is demonstrating the integration of UF6 cylinder tracking, using RF technology, with continuous load cell monitoring (CLCM) at mock UF6 feed and withdrawal (F&W) stations. CLCM and cylinder tracking are two of several continuous-monitoring technologies that show promise in providing integrated safeguards of F&W operations at enrichment plants. Integrating different monitoring technologies allows advanced, automated event processing to screen innocuous events thereby minimizing false alerts to independent inspectors. Traditionally, international inspectors rely on batch verification of material inputs and outputs derived from operator declarations and periodic on-site inspections at uranium enrichment plants or other nuclear processingmore » facilities. Continuously monitoring F&W activities between inspections while providing filtered alerts of significant operational events will substantially increase the amount of valuable information available to inspectors thereby promising to enhance the effectiveness of safeguards and to improve efficiency in conducting on-site inspections especially at large plants for ensuring that all operations are declared.« less

L-band Microwave Remote Sensing and Land Data Assimilation Improve the Representation of Prestorm Soil Moisture Conditions for Hydrologic Forecasting

NASA Technical Reports Server (NTRS)

Crow, W. T.; Chen, F.; Reichle, R. H.; Liu, Q.

2017-01-01

Recent advances in remote sensing and land data assimilation purport to improve the quality of antecedent soil moisture information available for operational hydrologic forecasting. We objectively validate this claim by calculating the strength of the relationship between storm-scale runoff ratio (i.e., total stream flow divided by total rainfall accumulation in depth units) and pre-storm surface soil moisture estimates from a range of surface soil moisture data products. Results demonstrate that both satellite-based, L-band microwave radiometry and the application of land data assimilation techniques have significantly improved the utility of surface soil moisture data sets for forecasting stream flow response to future rainfall events.

Test and evaluation of constant-flow devices for use in SSN AFFF proportioning systems. Interim report, January-May 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, F.W.; Back, G.G.; Burns, R.E.

1986-11-04

Constant flow devices, which deliver a constant flow of liquid over a range of upstream and downstream pressures, have been suggested as an alternative to orifice plates for proportioning AFFF in SSN 21 fire-suppression systems. Operational and performance characteristics of two lightweight, inexpensive, commercially available constant-flow devices have significant advantages over orifice plates. Both models tested, however, showed performance degradation when subjected to simulated service conditions. A constant flow device with improved resistance to wear and to AFFF exposure is desirable. Since the constant-flow control devices tested improves proportioning efficiency but do not have optimum characteristics, investigation of improved devicesmore » or methods is recommended.« less

L-band microwave remote sensing and land data assimilation improve the representation of pre-storm soil moisture conditions for hydrologic forecasting.

PubMed

Crow, W T; Chen, F; Reichle, R H; Liu, Q

2017-06-16

Recent advances in remote sensing and land data assimilation purport to improve the quality of antecedent soil moisture information available for operational hydrologic forecasting. We objectively validate this claim by calculating the strength of the relationship between storm-scale runoff ratio (i.e., total stream flow divided by total rainfall accumulation in depth units) and pre-storm surface soil moisture estimates from a range of surface soil moisture data products. Results demonstrate that both satellite-based, L-band microwave radiometry and the application of land data assimilation techniques have significantly improved the utility of surface soil moisture data sets for forecasting stream flow response to future rainfall events.

L-band microwave remote sensing and land data assimilation improve the representation of pre-storm soil moisture conditions for hydrologic forecasting

PubMed Central

Crow, W.T.; Chen, F.; Reichle, R.H.; Liu, Q.

2018-01-01

Recent advances in remote sensing and land data assimilation purport to improve the quality of antecedent soil moisture information available for operational hydrologic forecasting. We objectively validate this claim by calculating the strength of the relationship between storm-scale runoff ratio (i.e., total stream flow divided by total rainfall accumulation in depth units) and pre-storm surface soil moisture estimates from a range of surface soil moisture data products. Results demonstrate that both satellite-based, L-band microwave radiometry and the application of land data assimilation techniques have significantly improved the utility of surface soil moisture data sets for forecasting stream flow response to future rainfall events. PMID:29657342

Improved Cryogenic Optical Test Capability at Marshall Space Flight Center's X-ray Cryogenic Test Facility

NASA Technical Reports Server (NTRS)

Kegley, Jeffrey; Haight, Harlan; Hogue, William; Carpenter, Jay; Siler, Richard; Wright, Ernie; Eng, Ron; Baker, Mark; McCracken, Jeff

2005-01-01

Marshall Space Flight Center's X-ray & Cryogenic Test Facility (XRCF) has been performing optical wavefront testing and thermal structural deformation testing at subliquid nitrogen cryogenic temperatures since 1999. Recent modifications have been made to the facility in support of the James Webb Space Telescope (JWST) program. The test article envelope and the chamber's refrigeration capacity have both been increased. A new larger helium-cooled enclosure has been added to the existing enclosure increasing both the cross-sectional area and the length. This new enclosure is capable of supporting six JWST Primary Mirror Segment Assemblies. A second helium refrigeration system has been installed essentially doubling the cooling capacity available at the facility. Modifications have also been made to the optical instrumentation area. Improved access is now available for both the installation and operation of optical instrumentation outside the vacuum chamber. Chamber configuration, specifications, and performance data will be presented.

A new preparedness policy for EMS logistics.

PubMed

Lee, Seokcheon

2017-03-01

Response time in emergency medical services (EMS) is defined as the interval for an ambulance to arrive the scene after receipt of a 911 call. When several ambulances are available upon the receipt of a new call, a decision of selecting an ambulance has to be made in an effort to reduce response time. Dispatching the closest unit available is commonly used in practice; however, recently the Preparedness policy was designed that is in a simplistic form yet being capable of securing a long-term efficiency. This research aims to improve the Preparedness policy, resolving several critical issues inherent in the current form of the policy. The new Preparedness policy incorporates a new metric of preparedness based on the notion of centrality and involves a tuning parameter, weight on preparedness, which has to be appropriately chosen according to operational scenario. Computational experiment shows that the new policy significantly improves the former policy robustly in various scenarios.

Expression microdissection adapted to commercial laser dissection instruments

PubMed Central

Hanson, Jeffrey C; Tangrea, Michael A; Kim, Skye; Armani, Michael D; Pohida, Thomas J; Bonner, Robert F; Rodriguez-Canales, Jaime; Emmert-Buck, Michael R

2016-01-01

Laser-based microdissection facilitates the isolation of specific cell populations from clinical or animal model tissue specimens for molecular analysis. Expression microdissection (xMD) is a second-generation technology that offers considerable advantages in dissection capabilities; however, until recently the method has not been accessible to investigators. This protocol describes the adaptation of xMD to commonly used laser microdissection instruments and to a commercially available handheld laser device in order to make the technique widely available to the biomedical research community. The method improves dissection speed for many applications by using a targeting probe for cell procurement in place of an operator-based, cell-by-cell selection process. Moreover, xMD can provide improved dissection precision because of the unique characteristics of film activation. The time to complete the protocol is highly dependent on the target cell population and the number of cells needed for subsequent molecular analysis. PMID:21412274

Addendum: Development of a preprototype times wastewater recovery subsystem

NASA Technical Reports Server (NTRS)

Dehner, G. F.

1984-01-01

The results of the second generation operational improvements and the TIMES (Thermoelectric Integrated Membrane Evaporation Subsystem) 2 study are covered. Areas covered in the second generation operational improvements are improved temperature control, water quality improvements, subsytem operational improvements, solid handling improvements, wastewater pretreatment optimization, and membrane rejuvenation concepts. The task for the TIMES 2 study are thermoelectric regenerator improvement, recycle loop pH operational criteria, recycle loop component optimization, and hollow fiber membrane evaporator improvement. Results are presented and conclusions are drawn from both studies.

Improvements of the surgical technique on the established mouse model of orthotopic single lung transplantation.

PubMed

Zheng, Zhikun; Wang, Jianjun; Huang, Xia; Jiang, Ke; Nie, Jun; Qiao, Xinwei; Li, Jinsong

2013-01-01

A wide range of knockout and transgenic murine models for the study of nonimmune and immune mechanisms in lung transplants are available nowadays, but the microsurgical techniques are difficult to learn. We describe methods to simplify techniques and facilitate learning. Traditional procedures were implemented to perform lung transplants in 30 cases (group 1). Improved techniques which included cuff without tail, broadening of the cuff diameter for bronchus, establishment of one tunnel between three structures, innovative technology of the vascular anastomosis and placement of the chest tube post-operation were used to perform lung transplants in 30 cases (group 2). The improved techniques considerably shorten operative times (96.75 ± 6.16 min and 85.32 ± 6.98 min in groups 1 and 2, respectively). The survival rates in the recipient animals were 86.7% and 96.7% in groups 1 and 2, respectively. Chest X-rays and macroscopic changes of transplanted recipients showed that grafts were well inflated on postoperative day 30. There was no significant difference of the arterial oxygen tension (PaO2) between two groups (115.9 ± 7.11 mm Hg and 116.3 ± 6.87 mm Hg in groups 1 and 2, respectively). Histologically, no lung injury was seen in grafts. We described the modified procedures of orthotopic left lung transplants in mice, which could shorten operative time and increase survival rate.

TFTR neutral beam control and monitoring for DT operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

O`Connor, T.; Kamperschroer, J.; Chu, J.

1995-12-31

Record fusion power output has recently been obtained in TFTR with the injection of deuterium and tritium neutral beams. This significant achievement was due in part to the controls, software, and data processing capabilities added to the neutral beam system for DT operations. Chief among these improvements was the addition of SUN workstations and large dynamic data storage to the existing Central Instrumentation Control and Data Acquisition (CICADA) system. Essentially instantaneous look back over the recent shot history has been provided for most beam waveforms and analysis results. Gas regulation controls allowing remote switchover between deuterium and tritium were alsomore » added. With these tools, comparison of the waveforms and data of deuterium and tritium for four test conditioning pulses quickly produced reliable tritium setpoints. Thereafter, all beam conditioning was performed with deuterium, thus saving the tritium supply for the important DT injection shots. The lookback capability also led to modifications of the gas system to improve reliability and to control ceramic valve leakage by backbiasing. Other features added to improve the reliability and availability of DT neutral beam operations included master beamline controls and displays, a beamline thermocouple interlock system, a peak thermocouple display, automatic gas inventory and cryo panel gas loading monitoring, beam notching controls, a display of beam/plasma interlocks, and a feedback system to control beam power based on plasma conditions.« less

Improved JPEG anti-forensics with better image visual quality and forensic undetectability.

PubMed

Singh, Gurinder; Singh, Kulbir

2017-08-01

There is an immediate need to validate the authenticity of digital images due to the availability of powerful image processing tools that can easily manipulate the digital image information without leaving any traces. The digital image forensics most often employs the tampering detectors based on JPEG compression. Therefore, to evaluate the competency of the JPEG forensic detectors, an anti-forensic technique is required. In this paper, two improved JPEG anti-forensic techniques are proposed to remove the blocking artifacts left by the JPEG compression in both spatial and DCT domain. In the proposed framework, the grainy noise left by the perceptual histogram smoothing in DCT domain can be reduced significantly by applying the proposed de-noising operation. Two types of denoising algorithms are proposed, one is based on the constrained minimization problem of total variation of energy and other on the normalized weighted function. Subsequently, an improved TV based deblocking operation is proposed to eliminate the blocking artifacts in the spatial domain. Then, a decalibration operation is applied to bring the processed image statistics back to its standard position. The experimental results show that the proposed anti-forensic approaches outperform the existing state-of-the-art techniques in achieving enhanced tradeoff between image visual quality and forensic undetectability, but with high computational cost. Copyright © 2017 Elsevier B.V. All rights reserved.

A New Generation of Electrical Power Supply for Telecom Satellites

NASA Astrophysics Data System (ADS)

Bouhours, Gilles; Asplanato, Remi; Rebuffel, Christophe; Pasquet, Jean-Marie; Bardin, Bertrand; Deplus, Nicolas; Lempereur, Vincent

2014-08-01

This paper presents the main features of the new power subsystem generation for the Thales Alenia Space (TAS) Spacebus platforms.All its components (Solar Array, Solar Array Drive Mechanism, Power Conditioning Unit and Lithium-Ion batteries) have been upgraded, taking advantage of the latest available technologies. The modularity has been improved to perfectly match the sizing of each unit to the satellite power level requirement. These two improvements lead to optimal mass and cost over the whole power range.In addition, the customer benefits from a fully automatic operation of the subsystem, including redundancy, making the ground station workload negligible, even during eclipse periods. Finally, the capability to support any type of payload has been further improved, in terms of overall power level and operating modes. Payload pulsed operation capability has been especially increased to support all anticipated mission requirements. In parallel to the PCU hardware, a detailed electrical model has also been developed and correlated to analyse the regulation performance in any nominal or degraded mode. An extensive set of tests provides a verification of performances and interfaces, hardware as well as software.This paper will first describe the main requirements considered in this development. Then, the architecture will be detailed, showing how the requirements have been fulfilled. The design of each unit will be shortly presented, and finally the correlation between the regulation analysis model and the EQM measurements will be illustrated.

Modernization of the USGS Hawaiian Volcano Observatory Seismic Processing Infrastructure

NASA Astrophysics Data System (ADS)

Antolik, L.; Shiro, B.; Friberg, P. A.

2016-12-01

The USGS Hawaiian Volcano Observatory (HVO) operates a Tier 1 Advanced National Seismic System (ANSS) seismic network to monitor, characterize, and report on volcanic and earthquake activity in the State of Hawaii. Upgrades at the observatory since 2009 have improved the digital telemetry network, computing resources, and seismic data processing with the adoption of the ANSS Quake Management System (AQMS) system. HVO aims to build on these efforts by further modernizing its seismic processing infrastructure and strengthen its ability to meet ANSS performance standards. Most notably, this will also allow HVO to support redundant systems, both onsite and offsite, in order to provide better continuity of operation during intermittent power and network outages. We are in the process of implementing a number of upgrades and improvements on HVO's seismic processing infrastructure, including: 1) Virtualization of AQMS physical servers; 2) Migration of server operating systems from Solaris to Linux; 3) Consolidation of AQMS real-time and post-processing services to a single server; 4) Upgrading database from Oracle 10 to Oracle 12; and 5) Upgrading to the latest Earthworm and AQMS software. These improvements will make server administration more efficient, minimize hardware resources required by AQMS, simplify the Oracle replication setup, and provide better integration with HVO's existing state of health monitoring tools and backup system. Ultimately, it will provide HVO with the latest and most secure software available while making the software easier to deploy and support.

Bringing the CMS distributed computing system into scalable operations

NASA Astrophysics Data System (ADS)

Belforte, S.; Fanfani, A.; Fisk, I.; Flix, J.; Hernández, J. M.; Kress, T.; Letts, J.; Magini, N.; Miccio, V.; Sciabà, A.

2010-04-01

Establishing efficient and scalable operations of the CMS distributed computing system critically relies on the proper integration, commissioning and scale testing of the data and workload management tools, the various computing workflows and the underlying computing infrastructure, located at more than 50 computing centres worldwide and interconnected by the Worldwide LHC Computing Grid. Computing challenges periodically undertaken by CMS in the past years with increasing scale and complexity have revealed the need for a sustained effort on computing integration and commissioning activities. The Processing and Data Access (PADA) Task Force was established at the beginning of 2008 within the CMS Computing Program with the mandate of validating the infrastructure for organized processing and user analysis including the sites and the workload and data management tools, validating the distributed production system by performing functionality, reliability and scale tests, helping sites to commission, configure and optimize the networking and storage through scale testing data transfers and data processing, and improving the efficiency of accessing data across the CMS computing system from global transfers to local access. This contribution reports on the tools and procedures developed by CMS for computing commissioning and scale testing as well as the improvements accomplished towards efficient, reliable and scalable computing operations. The activities include the development and operation of load generators for job submission and data transfers with the aim of stressing the experiment and Grid data management and workload management systems, site commissioning procedures and tools to monitor and improve site availability and reliability, as well as activities targeted to the commissioning of the distributed production, user analysis and monitoring systems.

A multiband radiometer and data acquisition system for remote sensing field research

NASA Technical Reports Server (NTRS)

Bauer, M. E. (Principal Investigator); Robinson, B. F.; Dewitt, D. P.; Silva, L. F.; Vanderbilt, V. C.

1981-01-01

Specifications are described for a recently developed prototype multispectral data acquisition system which consists of multiband radiometer with 8 bands between 0.4 and 12.5 micrometers and a data recording module to record data from the radometer and ancillary sources. The systems is adaptable to helicopter, truck, or tripod platforms, as well as hand-held operation. The general characteristics are: (1) comparatively inexpensive to acquire, maintain and operate; (2) simple to operate and calibrate; (3) complete with data hardware and software; and (4) well documented for use by researchers. The instrument system is to be commercially available and can be utilized by many researchers to obtain large numbers of accurate, calibrated spectral measurements. It can be a key element in improving and advancing the capability for field research in remote sensing.

Applications systems verification and transfer project. Volume 3: Operational applications of satellite snow cover observations in California

NASA Technical Reports Server (NTRS)

Brown, A. J.; Hannaford, J. F.

1981-01-01

Five southern Sierra snowmelt basins and two northern Sierra-Southern Cascade snowmelt basins were used to evaluate the effect on operational water supply forecasting from satellite imagery. Manual photointerpretation techniques were used to obtain SCA and equivalent snow line for the years 1973 to 1979 for the seven test basins using LANDSAT imagery and GOES imagery. The use of SCA was tested operationally in 1977-79. Results indicate the addition of SCA improve the water supply forecasts during the snowmelt phase for these basins where there may be an unusual distribution of snowpack throughout the basin, or where there is a limited amount of real time data available. A high correlation to runoff was obtained when SCA was combined with snow water content data obtained from reporting snow sensors.

Conceptual design of distillation-based hybrid separation processes.

PubMed

Skiborowski, Mirko; Harwardt, Andreas; Marquardt, Wolfgang

2013-01-01

Hybrid separation processes combine different separation principles and constitute a promising design option for the separation of complex mixtures. Particularly, the integration of distillation with other unit operations can significantly improve the separation of close-boiling or azeotropic mixtures. Although the design of single-unit operations is well understood and supported by computational methods, the optimal design of flowsheets of hybrid separation processes is still a challenging task. The large number of operational and design degrees of freedom requires a systematic and optimization-based design approach. To this end, a structured approach, the so-called process synthesis framework, is proposed. This article reviews available computational methods for the conceptual design of distillation-based hybrid processes for the separation of liquid mixtures. Open problems are identified that must be addressed to finally establish a structured process synthesis framework for such processes.

Historical data recording for process computers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hale, J.C.; Sellars, H.L.

1981-11-01

Computers have been used to monitor and control chemical and refining processes for more than 15 years. During this time, there has been a steady growth in the variety and sophistication of the functions performed by these process computers. Early systems were limited to maintaining only current operating measurements, available through crude operator's consoles or noisy teletypes. The value of retaining a process history, that is, a collection of measurements over time, became apparent, and early efforts produced shift and daily summary reports. The need for improved process historians which record, retrieve and display process information has grown as processmore » computers assume larger responsibilities in plant operations. This paper describes newly developed process historian functions that have been used on several of its in-house process monitoring and control systems in Du Pont factories. 3 refs.« less

xLuna - D emonstrator on ESA Mars Rover

NASA Astrophysics Data System (ADS)

Braga, P.; Henriques, L.; Carvalho, B.; Chevalley, P.; Zulianello, M.

2008-08-01

There is a significant gap between the services offered by existing space qualified Real-Time Operating Systems (RTOS) and those required by the most demanding future space applications. New requirements for autonomy, terrain mapping and navigation, Simultaneous Location and Mapping (SLAM), improvement of the throughput of science tasks, all demand high level services such as file systems or POSIX compliant interfaces. xLuna is an operating system that aims fulfilling these new requirements. Besides providing the typical services that of an RTOS (tasks and interrupts management, timers, message queues, etc), it also includes most of the features available in modern general-purpose operating systems, such as Linux. This paper describes a case study that proposes to demonstrate the usage of xLuna on board a rover currently in use for the development of algorithms in preparation of a mission to Mars.

Reactive, Safe Navigation for Lunar and Planetary Robots

NASA Technical Reports Server (NTRS)

Utz, Hans; Ruland, Thomas

2008-01-01

When humans return to the moon, Astronauts will be accompanied by robotic helpers. Enabling robots to safely operate near astronauts on the lunar surface has the potential to significantly improve the efficiency of crew surface operations. Safely operating robots in close proximity to astronauts on the lunar surface requires reactive obstacle avoidance capabilities not available on existing planetary robots. In this paper we present work on safe, reactive navigation using a stereo based high-speed terrain analysis and obstacle avoidance system. Advances in the design of the algorithms allow it to run terrain analysis and obstacle avoidance algorithms at full frame rate (30Hz) on off the shelf hardware. The results of this analysis are fed into a fast, reactive path selection module, enforcing the safety of the chosen actions. The key components of the system are discussed and test results are presented.

Remote Energy Monitoring System via Cellular Network

NASA Astrophysics Data System (ADS)

Yunoki, Shoji; Tamaki, Satoshi; Takada, May; Iwaki, Takashi

Recently, improvement on power saving and cost efficiency by monitoring the operation status of various facilities over the network has gained attention. Wireless network, especially cellular network, has advantage in mobility, coverage, and scalability. On the other hand, it has disadvantage of low reliability, due to rapid changes in the available bandwidth. We propose a transmission control scheme based on data priority and instantaneous available bandwidth to realize a highly reliable remote monitoring system via cellular network. We have developed our proposed monitoring system and evaluated the effectiveness of our scheme, and proved it reduces the maximum transmission delay of sensor status to 1/10 compared to best effort transmission.

Operational Soil Moisture Retrieval Techniques: Theoretical Comparisons in the Context of Improving the NASA Standard Approach

NASA Astrophysics Data System (ADS)

Mladenova, I. E.; Jackson, T. J.; Bindlish, R.; Njoku, E. G.; Chan, S.; Cosh, M. H.

2012-12-01

We are currently evaluating potential improvements to the standard NASA global soil moisture product derived using observations acquired from the Advanced Microwave Scanning Radiometer-Earth Observing System (AMSR-E). A major component of this effort is a thorough review of the theoretical basis of available passive-based soil moisture retrieval algorithms suitable for operational implementation. Several agencies provide routine soil moisture products. Our research focuses on five well-establish techniques that are capable of carrying out global retrieval using the same AMSR-E data set as the NASA approach (i.e. X-band brightness temperature data). In general, most passive-based algorithms include two major components: radiative transfer modeling, which provides the smooth surface reflectivity properties of the soil surface, and a complex dielectric constant model of the soil-water mixture. These two components are related through the Fresnel reflectivity equations. Furthermore, the land surface temperature, vegetation, roughness and soil properties need to be adequately accounted for in the radiative transfer and dielectric modeling. All of the available approaches we have examined follow the general data processing flow described above, however, the actual solutions as well as the final products can be very different. This is primarily a result of the assumptions, number of sensor variables utilized, the selected ancillary data sets and approaches used to account for the effect of the additional geophysical variables impacting the measured signal. The operational NASA AMSR-E-based retrievals have been shown to have a dampened temporal response and sensitivity range. Two possible approaches to addressing these issues are being evaluated: enhancing the theoretical basis of the existing algorithm, if feasible, or directly adjusting the dynamic range of the final soil moisture product. Both of these aspects are being actively investigated and will be discussed in our talk. Improving the quality and reliability of the global soil moisture product would result in greater acceptance and utilization in the related applications. USDA is an equal opportunity provider and employer.

Fiscalini Farms Biomass Energy Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

William Stringfellow; Mary Kay Camarillo; Jeremy Hanlon

2011-09-30

In this final report describes and documents research that was conducted by the Ecological Engineering Research Program (EERP) at the University of the Pacific (Stockton, CA) under subcontract to Fiscalini Farms LP for work under the Assistance Agreement DE-EE0001895 'Measurement and Evaluation of a Dairy Anaerobic Digestion/Power Generation System' from the United States Department of Energy, National Energy Technology Laboratory. Fiscalini Farms is operating a 710 kW biomass-energy power plant that uses bio-methane, generated from plant biomass, cheese whey, and cattle manure via mesophilic anaerobic digestion, to produce electricity using an internal combustion engine. The primary objectives of the projectmore » were to document baseline conditions for the anaerobic digester and the combined heat and power (CHP) system used for the dairy-based biomass-energy production. The baseline condition of the plant was evaluated in the context of regulatory and economic constraints. In this final report, the operation of the plant between start-up in 2009 and operation in 2010 are documented and an interpretation of the technical data is provided. An economic analysis of the biomass energy system was previously completed (Appendix A) and the results from that study are discussed briefly in this report. Results from the start-up and first year of operation indicate that mesophilic anaerobic digestion of agricultural biomass, combined with an internal combustion engine, is a reliable source of alternative electrical production. A major advantage of biomass energy facilities located on dairy farms appears to be their inherent stability and ability to produce a consistent, 24 hour supply of electricity. However, technical analysis indicated that the Fiscalini Farms system was operating below capacity and that economic sustainability would be improved by increasing loading of feedstocks to the digester. Additional operational modifications, such as increased utilization of waste heat and better documentation of potential of carbon credits, would also improve the economic outlook. Analysis of baseline operational conditions indicated that a reduction in methane emissions and other greenhouse gas savings resulted from implementation of the project. The project results indicate that using anaerobic digestion to produce bio-methane from agricultural biomass is a promising source of electricity, but that significant challenges need to be addressed before dairy-based biomass energy production can be fully integrated into an alternative energy economy. The biomass energy facility was found to be operating undercapacity. Economic analysis indicated a positive economic sustainability, even at the reduced power production levels demonstrated during the baseline period. However, increasing methane generation capacity (via the importation of biomass codigestate) will be critical for increasing electricity output and improving the long-term economic sustainability of the operation. Dairy-based biomass energy plants are operating under strict environmental regulations applicable to both power-production and confined animal facilities and novel approached are being applied to maintain minimal environmental impacts. The use of selective catalytic reduction (SCR) for nitrous oxide control and a biological hydrogen sulfide control system were tested at this facility. Results from this study suggest that biomass energy systems can be compliant with reasonable scientifically based air and water pollution control regulations. The most significant challenge for the development of biomass energy as a viable component of power production on a regional scale is likely to be the availability of energy-rich organic feedstocks. Additionally, there needs to be further development of regional expertise in digester and power plant operations. At the Fiscalini facility, power production was limited by the availability of biomass for methane generation, not the designed system capacity. During the baseline study period, feedstocks included manure, sudan grass silage, and refused-feed. The ability of the dairy to produce silage in excess of on-site feed requirements limited power production. The availability of biomass energy crops and alternative feedstocks, such as agricultural and food wastes, will be a major determinant to the economic and environmental sustainability of biomass based electricity production.« less

Enhanced Engine Control for Emergency Operation

NASA Technical Reports Server (NTRS)

Litt, Jonathan S.

2012-01-01

C-MAPSS40k engine simulation has been developed and is available to the public. The authenticity of the engine performance and controller enabled the development of realistic enhanced control modes through controller modification alone. Use of enhanced control modes improved stability and control of an impaired aircraft. - Fast Response is useful for manual manipulation of the throttles - Use of Fast Response improved stability as part of a yaw rate feedback system. - Use of Overthrust shortened takeoff distance, but was generally useful in flight, too. Initial lack of pilot familiarity resulted in discomfort, especially with yaw rate feedback, but that was the only drawback, overall the pilot found the enhanced modes very helpful.

Minimally invasive aortic valve replacement in high risk patient groups

PubMed Central

Lewis, Harriet; Benedetto, Umberto; Caputo, Massimo; Angelini, Gianni; Vohra, Hunaid A.

2017-01-01

Minimally invasive aortic valve replacement (AVR) aims to preserve the sternal integrity and improve postoperative outcomes. In low risk patients, this technique can be achieved with comparable mortality to the conventional approach and there is evidence of possible reduction in intensive care and hospital length of stay, transfusion requirement, renal dysfunction, improved respiratory function and increased patient satisfaction. In this review, we aim to asses if these benefits can be transferred to the high risk patient groups. We therefore, discuss the available evidence for the following high risk groups: elderly patients, re-operative surgery, poor lung function, pulmonary hypertension, obesity, concomitant procedures and high risk score cohorts. PMID:28740685

Simple, low-noise piezo driver with feed-forward for broad tuning of external cavity diode lasers.

PubMed

Doret, S Charles

2018-02-01

We present an inexpensive, low-noise (<260 μV rms , 0.1 Hz-100 kHz) design for a piezo driver suitable for frequency tuning of external-cavity diode lasers. This simple driver improves upon many commercially available drivers by incorporating circuitry to produce a "feed-forward" signal appropriate for making simultaneous adjustments to the piezo voltage and laser current, enabling dramatic improvements in a mode-hop-free laser frequency tuning range. We present the theory behind our driver's operation, characterize its output noise, and demonstrate its use in absorption spectroscopy on the rubidium D 1 line.

Developing an Interactive Data Visualization Tool to Assess the Impact of Decision Support on Clinical Operations.

PubMed

Huber, Timothy C; Krishnaraj, Arun; Monaghan, Dayna; Gaskin, Cree M

2018-05-18

Due to mandates from recent legislation, clinical decision support (CDS) software is being adopted by radiology practices across the country. This software provides imaging study decision support for referring providers at the point of order entry. CDS systems produce a large volume of data, providing opportunities for research and quality improvement. In order to better visualize and analyze trends in this data, an interactive data visualization dashboard was created using a commercially available data visualization platform. Following the integration of a commercially available clinical decision support product into the electronic health record, a dashboard was created using a commercially available data visualization platform (Tableau, Seattle, WA). Data generated by the CDS were exported from the data warehouse, where they were stored, into the platform. This allowed for real-time visualization of the data generated by the decision support software. The creation of the dashboard allowed the output from the CDS platform to be more easily analyzed and facilitated hypothesis generation. Integrating data visualization tools into clinical decision support tools allows for easier data analysis and can streamline research and quality improvement efforts.

Shuttle Liquid Fly Back Booster Configuration Options

NASA Technical Reports Server (NTRS)

Healy, T. J., Jr.

1998-01-01

This paper surveys the basic configuration options available to a Liquid Fly Back Booster (LFBB), integrated with the Space Shuttle system. The background of the development of the LFBB concept is given. The influence of the main booster engine (BME) installations and the Fly Back Engine (FBE) installation on the aerodynamic configurations are also discussed. Limits on the LFBB configuration design space imposed by the existing Shuttle flight and ground elements are also described. The objective of the paper is to put the constrains and design space for an LFBB in perspective. The object of the work is to define LFBB configurations that significantly improve safety, operability, reliability and performance of the Shuttle system and dramatically lower operations costs.

NASA Supercomputer Improves Prospects for Ocean Climate Research

NASA Technical Reports Server (NTRS)

Menemenlis, D.; Hill, C.; Adcroft, A.; Campin, J. -M.; Cheng, B.; Ciotti, B.; Fukumori, I.; Heimbach, P.; Henze, C.; Kohl, A.;

Real-time new satellite product demonstration from microwave sensors and GOES-16 at NRL TC web

NASA Astrophysics Data System (ADS)

Cossuth, J.; Richardson, K.; Surratt, M. L.; Bankert, R.

2017-12-01

The Naval Research Laboratory (NRL) Tropical Cyclone (TC) satellite webpage (https://www.nrlmry.navy.mil/TC.html) provides demonstration analyses of storm imagery to benefit operational TC forecast centers around the world. With the availability of new spectral information provided by GOES-16 satellite data and recent research into improved visualization methods of microwave data, experimental imagery was operationally tested to visualize the structural changes of TCs during the 2017 hurricane season. This presentation provides an introduction into these innovative satellite analysis methods, NRL's next generation satellite analysis system (the Geolocated Information Processing System, GeoIPSTM), and demonstration the added value of additional spectral frequencies when monitoring storms in near-realtime.

High-Energy-Density Electrolytic Capacitors

NASA Technical Reports Server (NTRS)

Yen, Shiao-Ping S.; Lewis, Carol R.

1993-01-01

Reductions in weight and volume make new application possible. Supercapacitors and improved ultracapacitors advanced electrolytic capacitors developed for use as electric-load-leveling devices in such applications as electric vehicle propulsion systems, portable power tools, and low-voltage pulsed power supplies. One primary advantage: offer power densities much higher than storage batteries. Capacitors used in pulse mode, with short charge and discharge times. Derived from commercially available ultracapacitors. Made of lightweight materials; incorporate electrode/electrolyte material systems capable of operation at voltages higher than previous electrode/electrolyte systems. By use of innovative designs and manufacturing processes, made in wide range of rated capacitances and in rated operating potentials ranging from few to several hundred volts.

Performance seeking control (PSC) for the F-15 highly integrated digital electronic control (HIDEC) aircraft

NASA Technical Reports Server (NTRS)

Orme, John S.

1995-01-01

The performance seeking control algorithm optimizes total propulsion system performance. This adaptive, model-based optimization algorithm has been successfully flight demonstrated on two engines with differing levels of degradation. Models of the engine, nozzle, and inlet produce reliable, accurate estimates of engine performance. But, because of an observability problem, component levels of degradation cannot be accurately determined. Depending on engine-specific operating characteristics PSC achieves various levels performance improvement. For example, engines with more deterioration typically operate at higher turbine temperatures than less deteriorated engines. Thus when the PSC maximum thrust mode is applied, for example, there will be less temperature margin available to be traded for increasing thrust.

Scalable geocomputation: evolving an environmental model building platform from single-core to supercomputers

NASA Astrophysics Data System (ADS)

Schmitz, Oliver; de Jong, Kor; Karssenberg, Derek

2017-04-01

There is an increasing demand to run environmental models on a big scale: simulations over large areas at high resolution. The heterogeneity of available computing hardware such as multi-core CPUs, GPUs or supercomputer potentially provides significant computing power to fulfil this demand. However, this requires detailed knowledge of the underlying hardware, parallel algorithm design and the implementation thereof in an efficient system programming language. Domain scientists such as hydrologists or ecologists often lack this specific software engineering knowledge, their emphasis is (and should be) on exploratory building and analysis of simulation models. As a result, models constructed by domain specialists mostly do not take full advantage of the available hardware. A promising solution is to separate the model building activity from software engineering by offering domain specialists a model building framework with pre-programmed building blocks that they combine to construct a model. The model building framework, consequently, needs to have built-in capabilities to make full usage of the available hardware. Developing such a framework providing understandable code for domain scientists and being runtime efficient at the same time poses several challenges on developers of such a framework. For example, optimisations can be performed on individual operations or the whole model, or tasks need to be generated for a well-balanced execution without explicitly knowing the complexity of the domain problem provided by the modeller. Ideally, a modelling framework supports the optimal use of available hardware whichsoever combination of model building blocks scientists use. We demonstrate our ongoing work on developing parallel algorithms for spatio-temporal modelling and demonstrate 1) PCRaster, an environmental software framework (http://www.pcraster.eu) providing spatio-temporal model building blocks and 2) parallelisation of about 50 of these building blocks using the new Fern library (https://github.com/geoneric/fern/), an independent generic raster processing library. Fern is a highly generic software library and its algorithms can be configured according to the configuration of a modelling framework. With manageable programming effort (e.g. matching data types between programming and domain language) we created a binding between Fern and PCRaster. The resulting PCRaster Python multicore module can be used to execute existing PCRaster models without having to make any changes to the model code. We show initial results on synthetic and geoscientific models indicating significant runtime improvements provided by parallel local and focal operations. We further outline challenges in improving remaining algorithms such as flow operations over digital elevation maps and further potential improvements like enhancing disk I/O.

Improving operational plume forecasts

NASA Astrophysics Data System (ADS)

Balcerak, Ernie

2012-04-01

Forecasting how plumes of particles, such as radioactive particles from a nuclear disaster, will be transported and dispersed in the atmosphere is an important but computationally challenging task. During the Fukushima nuclear disaster in Japan, operational plume forecasts were produced each day, but as the emissions continued, previous emissions were not included in the simulations used for forecasts because it became impractical to rerun the simulations each day from the beginning of the accident. Draxler and Rolph examine whether it is possible to improve plume simulation speed and flexibility as conditions and input data change. The authors use a method known as a transfer coefficient matrix approach that allows them to simulate many radionuclides using only a few generic species for the computation. Their simulations work faster by dividing the computation into separate independent segments in such a way that the most computationally time consuming pieces of the calculation need to be done only once. This makes it possible to provide real-time operational plume forecasts by continuously updating the previous simulations as new data become available. They tested their method using data from the Fukushima incident to show that it performed well. (Journal of Geophysical Research-Atmospheres, doi:10.1029/2011JD017205, 2012)

Hubble Servicing Challenges Drive Innovation of Shuttle Rendezvous Techniques

NASA Technical Reports Server (NTRS)

Goodman, John L.; Walker, Stephen R.

2009-01-01

Hubble Space Telescope (HST) servicing, performed by Space Shuttle crews, has contributed to what is arguably one of the most successful astronomy missions ever flown. Both nominal and contingency proximity operations techniques were developed to enable successful servicing, while lowering the risk of damage to HST systems, and improve crew safety. Influencing the development of these techniques were the challenges presented by plume impingement and HST performance anomalies. The design of both the HST and the Space Shuttle was completed before the potential of HST contamination and structural damage by shuttle RCS jet plume impingement was fully understood. Relative navigation during proximity operations has been challenging, as HST was not equipped with relative navigation aids. Since HST reached orbit in 1990, proximity operations design for servicing missions has evolved as insight into plume contamination and dynamic pressure has improved and new relative navigation tools have become available. Servicing missions have provided NASA with opportunities to gain insight into servicing mission design and development of nominal and contingency procedures. The HST servicing experiences and lessons learned are applicable to other programs that perform on-orbit servicing and rendezvous, both human and robotic.

Quantum metrology with a transmon qutrit

NASA Astrophysics Data System (ADS)

Shlyakhov, A. R.; Zemlyanov, V. V.; Suslov, M. V.; Lebedev, A. V.; Paraoanu, G. S.; Lesovik, G. B.; Blatter, G.

2018-02-01

Making use of coherence and entanglement as metrological quantum resources allows us to improve the measurement precision from the shot-noise or quantum limit to the Heisenberg limit. Quantum metrology then relies on the availability of quantum engineered systems that involve controllable quantum degrees of freedom which are sensitive to the measured quantity. Sensors operating in the qubit mode and exploiting their coherence in a phase-sensitive measurement have been shown to approach the Heisenberg scaling in precision. Here, we show that this result can be further improved by operating the quantum sensor in the qudit mode, i.e., by exploiting d rather than two levels. Specifically, we describe the metrological algorithm for using a superconducting transmon device operating in a qutrit mode as a magnetometer. The algorithm is based on the base-3 semiquantum Fourier transformation and enhances the quantum theoretical performance of the sensor by a factor of 2. Even more, the practical gain of our qutrit implementation is found in a reduction of the number of iteration steps of the quantum Fourier transformation by the factor ln(2 )/ln(3 )≈0.63 compared to the qubit mode. We show that a two-tone capacitively coupled radio-frequency signal is sufficient for implementation of the algorithm.

Energy conversion/power plant cost-cutting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nichols, K.

This presentation by Kenneth Nichols, Barber-Nichols, Inc., is about cost-cutting in the energy conversion phase and power plant phase of geothermal energy production. Mr. Nichols discusses several ways in which improvements could be made, including: use of more efficient compressors and other equipment as they become available, anticipating reservoir resource decline and planning for it, running smaller binary systems independent of human operators, and designing plants so that they are relatively maintenance-free.

Research on Internal Controls and Auditing. Navy Financial Management Improvement Program. Volume 3.

DTIC Science & Technology

1980-06-01

facilities. NARDAC Pensacola, was formed in October, 1977 with the transfer of the Naval Education and Training Information Support o Activity (NETISA...to NAVDAC and the additional transfer of four other geographically separate data processing centers. Somewhere between 25 to 50 percent of the Navy’s...may change the jobs within the framework of the time and processing resources available. The automated system tells the operations personnel the setup

A Lean Approach to Improving SE Visibility in Large Operational Systems Evolution

DTIC Science & Technology

2013-06-01

large health care system of systems. To enhance both visibility and flow, the approach utilizes visualization techniques, pull-scheduling processes...development processes. This paper describes an example implementation of the concept in a large health care system of systems. To enhance both visibility...and then provides the results to the requestor as soon as available. Hospital System Information Support Development The health care SoS is a set

Technology Assessment for Future MILSATCOM Systems: The EHF Bands

DTIC Science & Technology

1979-04-01

improvements must be pursued to provide long life (7 to 10 years), higher efficiencies and higher power. 1. Current Availability A 4-watt helix TWT ... helix TWT ), adequate bandwidth for communications applications and efficiencies of 40-50%. An example is the 200-watt tube operating at 12 GHz with an...costly than its helix counterpart. In addition, experience with coupled-cavity tubes in space is rare. Consequently, coupled-cavity TWTs will only be

Achieving Higher-Fidelity Conjunction Analyses Using Cryptography to Improve Information Sharing

DTIC Science & Technology

2014-01-01

debris—the man-made orbital junk that represents a collision risk to operational satellites—is a growing threat that will increasingly affect future space ...Plans, Hq USAF. Library of Congress Cataloging-in-Publication Data is available for this publication. ISBN: 978-0-8330-8166-7 iii Preface Space ...reducing future debris populations using political and technical means. The 2010 U.S. Space Policy makes several policy recommendations for addressing

NON-STANDARD FIXED WING AVIATION: THE RECIPE FOR ADDRESSING SPECIALIZED MOBILITY SHORTFALLS

DTIC Science & Technology

2015-10-01

capabilities and logistics and evaluates the utilization of available non-standard aviation aircraft for Special Operations and compares the effectiveness and...ways to improve the efficiency and effectiveness of the balance between contract aviation assets and organic military assets being utilized to help...commander to effectively command and control (C2), all pose problems to the warfighter. It has been proven that “Ad-hoc attachment of air assets and

The feasibility, safety and outcomes of laparoscopic re-operation for achalasia.

PubMed

James, David R C; Purkayastha, Sanjay; Aziz, Omer; Amygdalos, Iakovos; Darzi, Ara W; Hanna, George B; Zacharakis, Emmanouil

2012-05-01

Heller myotomy for achalasia is associated with a recurrence rate of around 10%, thus reoperative surgery is often necessitated. This paper aims to review the available literature on laparoscopic reoperation for achalasia in order to assess its feasibility and effectiveness. A Medline, Embase, Ovid, Cochrane database and Google(TM) Scholar search was performed with the following Mesh terms: "laparoscopic", "redo", "reoperative", "Heller's", "esophagomyotomy" and "achalasia". Outcomes of interest included patient demographics and details of primary procedure, operative details, intra- and post operative complications and symptom scores. Seven studies reported outcomes from 54 cases. Conversion occurred in 7% (4/54) of cases. Thirteen percent (7/54) of patients sustained intra-operative gastric or oesophageal perforation; however these were all noted and repaired intra-operatively leading to no subsequent morbidity. No deaths were reported. Pre- and post operative symptom scores were heterogeneous, however did appear to improve after the procedure. This review demonstrates that laparoscopic reoperation for achalasia is feasible and safe with complication rates comparable to the primary laparoscopic operation. It is recommended that laparoscopic reoperative Heller's myotomy should only be performed by surgeons with special interest in oesophagogastric surgery and adequate experience in laparoscopic surgery for achalasia.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dempsey, Adam B.; Curran, Scott; Reitz, Rolf D.

The focus of the present paper was to characterize Reactivity Controlled Compression Ignition (RCCI) using a single-fuel approach of gasoline and gasoline mixed with a commercially available cetane improver on a multi-cylinder engine. RCCI was achieved by port-injecting a certification grade 96 research octane gasoline and direct-injecting the same gasoline mixed with various levels of a cetane improver, 2-ethylhexyl nitrate (EHN). The EHN volume percentages investigated in the direct-injected fuel were 10, 5, and 2.5%. The combustion phasing controllability and emissions of the different fueling combinations were characterized at 2300 rpm and 4.2 bar brake mean effective pressure over amore » variety of parametric investigations including direct injection timing, premixed gasoline percentage, and intake temperature. Comparisons were made to gasoline/diesel RCCI operation on the same engine platform at nominally the same operating condition. The experiments were conducted on a modern four cylinder light-duty diesel engine that was modified with a port-fuel injection system while maintaining the stock direct injection fuel system. The pistons were modified for highly premixed operation and feature an open shallow bowl design. The results indicate that the authority to control the combustion phasing through the fuel delivery strategy (e.g., direct injection timing or premixed gasoline percentage) is not a strong function of the EHN concentration in the direct-injected fuel. It was also observed that NOx emissions are a strong function of the global EHN concentration in-cylinder and the combustion phasing. Finally, in general, NOx emissions are significantly elevated for gasoline/gasoline+EHN operation compared with gasoline/diesel RCCI operation at a given operating condition.« less

Operational and financial impact of physician screening in the ED.

PubMed

Soremekun, Olanrewaju A; Biddinger, Paul D; White, Benjamin A; Sinclair, Julia R; Chang, Yuchiao; Carignan, Sarah B; Brown, David F M

2012-05-01

Physician screening is one of many front-end interventions being implemented to improve emergency department (ED) efficiency. We aimed to quantify the operational and financial impact of this intervention at an urban tertiary academic center. We conducted a 2-year before-after analysis of a physician screening system at an urban tertiary academic center with 90 000 annual visits. Financial impact consisted of the ED and inpatient revenue generated from the incremental capacity and the reduction in left without being seen (LWBS) rates. The ED and inpatient margin contribution as well as capital expenditure were based on available published data. We summarized the financial impact using net present value of future cash flows performing sensitivity analysis on the assumptions. Operational outcome measures were ED length of stay and percentage of LWBS. During the first year, we estimate the contribution margin of the screening system to be $2.71 million and the incremental operational cost to be $1.86 million. Estimated capital expenditure for the system was $1 200 000. The NPV of this investment was $2.82 million, and time to break even from the initial investment was 13 months. Operationally, despite a 16.7% increase in patient volume and no decrease in boarding hours, there was a 7.4% decrease in ED length of stay and a reduction in LWBS from 3.3% to 1.8%. In addition to improving operational measures, the implementation of a physician screening program in the ED allowed for an incremental increase in patient care capacity leading to an overall positive financial impact. Copyright © 2012 Elsevier Inc. All rights reserved.

Intraoperative Endotracheal Cuff Pressure Study: How Education and Availability of Manometers Help Guide Safer Pressures.

PubMed

Stevens, Gregory J; Warfel, Joel W; Aden, James K; Blackwell, Scott D

2018-02-13

Endotracheal intubation is a medical procedure that is often indicated in both the perioperative and critical care environments. Cuffed endotracheal tubes (ETT) allow for safer and more efficient delivery of positive pressure ventilation, as well as create a barrier to reduce the risk of micro-aspiration and anesthetic pollution in the operating room environment. Over-inflation of the endotracheal cuff can lead to serious and harmful sequelae. This study aimed to assess if departmental education paired with ready access to a manometer to assess cuff pressure would result in an improvement in the proportion of ETT cuff pressures in the goal range. A quality improvement study was conducted at the San Antonio Military Medical Center (SAMMC; Department of Defense hospital in San Antonio, TX). The initiative was divided into three key periods: pre-implementation, implementation, and post-implementation. During the pre-implementation period, ETT cuff pressures were obtained to assess the baseline state of ETT cuff pressures for patients in the operating room; the proportion of in-range (20-30 cmH2O) pressures was calculated. During the implementation phase, operating rooms were equipped with manometers and anesthesia departmental education was performed regarding the use of the manometers. Three months later, post-implementation cuff pressures were measured in the OR, and the proportion of in-range pressures was again calculated. The pre-implementation data showed an average cuff pressure of 48.92 cmH2O and a median of 38.5 cmH2O. Of the 100 pre-implementation pressures, 20 were in the goal range. Post-implementation data had an average cuff pressure of 41.96 cmH2O and a median of 30 cmH2O. A chi-squared test of pressures in the safe range from the pre-implementation versus post-implementation values yielded a highly significant p-value of 0.0003. The data from this study clearly demonstrated a statistically significant improvement in the proportion of in-range cuff pressures following the quality improvement initiative. This study supports the use of department-wide education and the availability of manometers in each OR to yield safer cuff pressures for intubated patients. This study did not aim to determine an optimal ETT cuff pressure, but utilized data already available to determine a safe cuff pressure. Further research needs to be performed to assess whether routine monitoring of cuff pressure results in improved patient outcomes. Published by Oxford University Press on behalf of the Association of Military Surgeons of the United States 2018. This work is written by (a) US Government employee(s) and is in the public domain in the US.

Non-Obstetric Surgical Care at Three Rural District Hospitals in Rwanda: More Human Capacity and Surgical Equipment May Increase Operative Care.

PubMed

Muhirwa, Ernest; Habiyakare, Caste; Hedt-Gauthier, Bethany L; Odhiambo, Jackline; Maine, Rebecca; Gupta, Neil; Toma, Gabriel; Nkurunziza, Theoneste; Mpunga, Tharcisse; Mukankusi, Jeanne; Riviello, Robert

2016-09-01

Most mortality attributable to surgical emergencies occurs in low- and middle-income countries. District hospitals, which serve as the first-level surgical facility in rural sub-Saharan Africa, are often challenged with limited surgical capacity. This study describes the presentation, management, and outcomes of non-obstetric surgical patients at district hospitals in Rwanda. This study included patients seeking non-obstetric surgical care at three district hospitals in rural Rwanda in 2013. Demographics, surgical conditions, patient care, and outcomes are described; operative and non-operative management were stratified by hospitals and differences assessed using Fisher's exact test. Of the 2660 patients who sought surgical care at the three hospitals, most were males (60.7 %). Many (42.6 %) were injured and 34.7 % of injuries were through road traffic crashes. Of presenting patients, 25.3 % had an operation, with patients presenting to Butaro District Hospital significantly more likely to receive surgery (57.0 %, p < 0.001). General practitioners performed nearly all operations at Kirehe and Rwinkwavu District Hospitals (98.0 and 100.0 %, respectively), but surgeons performed 90.6 % of the operations at Butaro District Hospital. For outcomes, 39.5 % of all patients were discharged without an operation, 21.1 % received surgery and were discharged, and 21.1 % were referred to tertiary facilities for surgical care. Significantly more patients in Butaro, the only site with a surgeon on staff and stronger surgical infrastructure, received surgery. Availing more surgeons who can address the most common surgical needs and improving supplies and equipment may improve outcomes at other districts. Surgical task sharing is recommended as a temporary solution.

NASA's Airborne Astronomy Program - Lessons For SOFIA

NASA Astrophysics Data System (ADS)

Erickson, Edwin F.

2007-07-01

Airborne astronomy was pioneered and has evolved at NASA Ames Research Center near San Francisco, California, since 1965. Nowhere else in the world has a similar program been implemented. Its many unique features deserve description, especially for the benefit of planning the operation of SOFIA, the Stratospheric Observatory for Infrared Astronomy, and in particular since NASA Headquarters’ recent decision to base SOFIA operations at Dryden Flight Research Center at Edwards, California instead of at Ames. The history of Ames’ airborne astronomy program is briefly summarized. Discussed in more detail are the operations and organization of the 21-year Kuiper Airborne Observatory (KAO) program, which provide important lessons for SOFIA. The KAO program is our best prototype for planning effective SOFIA operations. Principal features of the KAO program which should be retained on SOFIA are: unique science, innovative new science instruments and technologies, training of young scientists, an effective education and public outreach program, flexibility, continuous improvement, and efficient operations with a lean, well integrated team. KAO program features which should be improved upon with SOFIA are: (1) a management structure that is dedicated primarily to safely maximizing scientific productivity for the resources available, headed by a scientist who is the observatory director, and (2) stimuli to assure prompt distribution and accessibility of data to the scientific community. These and other recommendations were recorded by the SOFIA Science Working Group in 1995, when the KAO was decommissioned to start work on SOFIA. Further operational and organizational factors contributing to the success of the KAO program are described. Their incorporation into SOFIA operations will help assure the success of this new airborne observatory. SOFIA is supported by NASA in the U.S. and DLR (the German Aerospace Center) in Germany.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, Corrie E.; Harto, Christopher B.; Schroeder, Jenna N.

This report is the third in a series of reports sponsored by the U.S. Department of Energy Geothermal Technologies Program in which a range of water-related issues surrounding geothermal power production are evaluated. The first report made an initial attempt at quantifying the life cycle fresh water requirements of geothermal power-generating systems and explored operational and environmental concerns related to the geochemical composition of geothermal fluids. The initial analysis of life cycle fresh water consumption of geothermal power-generating systems identified that operational water requirements consumed the vast majority of water across the life cycle. However, it relied upon limited operationalmore » water consumption data and did not account for belowground operational losses for enhanced geothermal systems (EGSs). A second report presented an initial assessment of fresh water demand for future growth in utility-scale geothermal power generation. The current analysis builds upon this work to improve life cycle fresh water consumption estimates and incorporates regional water availability into the resource assessment to improve the identification of areas where future growth in geothermal electricity generation may encounter water challenges. This report is divided into nine chapters. Chapter 1 gives the background of the project and its purpose, which is to assess the water consumption of geothermal technologies and identify areas where water availability may present a challenge to utility-scale geothermal development. Water consumption refers to the water that is withdrawn from a resource such as a river, lake, or nongeothermal aquifer that is not returned to that resource. The geothermal electricity generation technologies evaluated in this study include conventional hydrothermal flash and binary systems, as well as EGSs that rely on engineering a productive reservoir where heat exists, but where water availability or permeability may be limited. Chapter 2 describes the approach and methods for this work and identifies the four power plant scenarios evaluated: a 20-MW EGS binary plant, a 50-MW EGS binary plant, a 10-MW hydrothermal binary plant, and a 50-MW hydrothermal flash plant. The methods focus on (1) the collection of data to improve estimation of EGS stimulation volumes, aboveground operational consumption for all geothermal technologies, and belowground operational consumption for EGS; and (2) the mapping of the geothermal and water resources of the western United States to assist in the identification of potential water challenges to geothermal growth. Chapters 3 and 4 present the water requirements for the power plant life cycle. Chapter 3 presents the results of the current data collection effort, and Chapter 4 presents the normalized volume of fresh water consumed at each life cycle stage per lifetime energy output for the power plant scenarios evaluated. Over the life cycle of a geothermal power plant, from construction through 30 years of operation, the majority of water is consumed by plant operations. For the EGS binary scenarios, where dry cooling was assumed, belowground operational water loss is the greatest contributor depending upon the physical and operational conditions of the reservoir. Total life cycle water consumption requirements for air-cooled EGS binary scenarios vary between 0.22 and 1.85 gal/kWh, depending upon the extent of belowground operational water consumption. The air-cooled hydrothermal binary and flash plants experience far less fresh water consumption over the life cycle, at 0.04 gal/kWh. Fresh water requirements associated with air- cooled binary operations are primarily from aboveground water needs, including dust control, maintenance, and domestic use. Although wet-cooled hydrothermal flash systems require water for cooling, these plants generally rely upon the geofluid, fluid from the geothermal reservoir, which typically has high salinity and total dissolved solids concentration and is much warmer than normal groundwater sources, for their cooling water needs; thus, while there is considerable geofluid loss at 2.7 gal/kWh, fresh water consumption during operations is similar to that of aircooled binary systems. Chapter 5 presents the assessment of water demand for future growth in deployment of utility-scale geothermal power generation. The approach combines the life cycle analysis of geothermal water consumption with a geothermal supply curve according to resource type, levelized cost of electricity (LCOE), and potential growth scenarios. A total of 17 growth scenarios were evaluated. In general, the scenarios that assumed lower costs for EGSs as a result of learning and technological improvements resulted in greater geothermal potential, but also significantly greater water demand due to the higher water consumption by EGSs. It was shown, however, that this effect could be largely mitigated if nonpotable water sources were used for belowground operational water demands. The geographical areas that showed the highest water demand for most growth scenarios were southern and northern California, as well as most of Nevada. In addition to water demand by geothermal power production, Chapter 5 includes data on water availability for geothermal development areas. A qualitative analysis is included that identifies some of the basins where the limited availability of water is most likely to affect the development of geothermal resources. The data indicate that water availability is fairly limited, especially under drought conditions, in most of the areas with significant near- and medium-term geothermal potential. Southern California was found to have the greatest potential for water-related challenges with its combination of high geothermal potential and limited water availability. The results of this work are summarized in Chapter 6. Overall, this work highlights the importance of utilizing dry cooling systems for binary and EGS systems and minimizing fresh water consumption throughout the life cycle of geothermal power development. The large resource base for EGSs represents a major opportunity for the geothermal industry; however, depending upon geology, these systems can require large quantities of makeup water due to belowground reservoir losses. Identifying potential sources of compatible degraded or low-quality water for use for makeup injection for EGS and flash systems represents an important opportunity to reduce the impacts of geothermal development on fresh water resources. The importance of identifying alternative water sources for geothermal systems is heightened by the fact that a large fraction of the geothermal resource is located in areas already experiencing water stress. Chapter 7 is a glossary of the technical terms used in the report, and Chapters 8 and 9 provide references and a bibliography, respectively.« less

Applications Integration Strategy in the Mission Development Process

NASA Astrophysics Data System (ADS)

Cox, E. L., Jr.

2016-12-01

NASA's Earth Science Applied Science Program has worked for the past four to five years with the Earth Science Division's Flight Program to cultivate an understanding of the importance of satellite remote sensing impacts on decision-making policy and decision support tools utilized by academia, state and local governments, other government agencies, private sector companies, and non-profit organizations. It has long been recognized that applications projects and studies in areas such as Health and Air Quality, Water Resources, Disasters, and Ecological Forecasting, have benefited and been enhanced through the use of satellite remote sensing. Applications researchers often use remote sensing data once it becomes available after the post-launch evaluation phase in the format and level of fidelity that is available. The results from the many applications projects, over the years, have been significant and there are countless examples of improvements and enhancements to operational systems and decision-making policies in the Applied Sciences community. However, feedback received from the applications community regarding the need for improved data availability and latency; processing and formatting, to name a few, prompted the idea of applied science involvement early in the life cycle of mission development. Over time, the Applied Science Program personnel have learned a great deal from the flight mission development life cycle process and recognized key areas of alignment. This presentation will discuss specific aspects of applied science that investigators should consider when proposing to future announcements involving an applications dimension. The Program's experience with user community needs, decision-making requirements, and stakeholder operations requirements will be highlighted.

A Role for Science in Responding to Health Crises

PubMed Central

Brothers, Reginald; Murata, Christina E.

2016-01-01

The Department of Homeland Security's (DHS) Science and Technology (S&T) Directorate plays a role in public health that extends beyond biodefense. These responsibilities were exercised as part of the 2014-16 Ebola outbreak, leading to productive and beneficial contributions to the international public health response and improved operations in the United States. However, we and others have identified numerous areas for improvement. Based on our successes and lessons learned, we propose a number of ways that DHS, the interagency, and academia can act now to ensure improved responses to future public health crises. These include pre-developing scientific capabilities to respond agnostically to threats, and disease-specific master question lists to organize and inform initial efforts. We are generating DHS-specific playbooks and tools for anticipating future needs and capturing requests from DHS components and our national and international partners, where efforts will also be used to refine and exercise communication and information-sharing practices. These experiences and improvement efforts have encouraged discussions on the role of science in developing government policy, specifically responding to public health crises. We propose specific considerations for both scientists and government decision makers to ensure that the best available science is incorporated into policy and operational decisions to facilitate highly effective responses to future health crises. PMID:27482881

On the use of controls for subsonic transport performance improvement: Overview and future directions

NASA Technical Reports Server (NTRS)

Gilyard, Glenn; Espana, Martin

1994-01-01

Increasing competition among airline manufacturers and operators has highlighted the issue of aircraft efficiency. Fewer aircraft orders have led to an all-out efficiency improvement effort among the manufacturers to maintain if not increase their share of the shrinking number of aircraft sales. Aircraft efficiency is important in airline profitability and is key if fuel prices increase from their current low. In a continuing effort to improve aircraft efficiency and develop an optimal performance technology base, NASA Dryden Flight Research Center developed and flight tested an adaptive performance seeking control system to optimize the quasi-steady-state performance of the F-15 aircraft. The demonstrated technology is equally applicable to transport aircraft although with less improvement. NASA Dryden, in transitioning this technology to transport aircraft, is specifically exploring the feasibility of applying adaptive optimal control techniques to performance optimization of redundant control effectors. A simulation evaluation of a preliminary control law optimizes wing-aileron camber for minimum net aircraft drag. Two submodes are evaluated: one to minimize fuel and the other to maximize velocity. This paper covers the status of performance optimization of the current fleet of subsonic transports. Available integrated controls technologies are reviewed to define approaches using active controls. A candidate control law for adaptive performance optimization is presented along with examples of algorithm operation.

Assimilation and High Resolution Forecasts of Surface and Near Surface Conditions for the 2010 Vancouver Winter Olympic and Paralympic Games

NASA Astrophysics Data System (ADS)

Bernier, Natacha B.; Bélair, Stéphane; Bilodeau, Bernard; Tong, Linying

2014-01-01

A dynamical model was experimentally implemented to provide high resolution forecasts at points of interests in the 2010 Vancouver Olympics and Paralympics Region. In a first experiment, GEM-Surf, the near surface and land surface modeling system, is driven by operational atmospheric forecasts and used to refine the surface forecasts according to local surface conditions such as elevation and vegetation type. In this simple form, temperature and snow depth forecasts are improved mainly as a result of the better representation of real elevation. In a second experiment, screen level observations and operational atmospheric forecasts are blended to drive a continuous cycle of near surface and land surface hindcasts. Hindcasts of the previous day conditions are then regarded as today's optimized initial conditions. Hence, in this experiment, given observations are available, observation driven hindcasts continuously ensure that daily forecasts are issued from improved initial conditions. GEM-Surf forecasts obtained from improved short-range hindcasts produced using these better conditions result in improved snow depth forecasts. In a third experiment, assimilation of snow depth data is applied to further optimize GEM-Surf's initial conditions, in addition to the use of blended observations and forecasts for forcing. Results show that snow depth and summer temperature forecasts are further improved by the addition of snow depth data assimilation.

Recent Improvement Of The Institutional Radioactive Waste Management System In Slovenia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sueiae, S.; Fabjan, M.; Hrastar, U.

2008-07-01

The task of managing institutional radioactive waste was assigned to the Slovenian National Agency for Radwaste Management by the Governmental Decree of May 1999. This task ranges from the collection of waste at users' premises to the storage in the Central Storage Facility in (CSF) and afterwards to the planned Low and Intermediate Level Waste (LILW) repository. By this Decree ARAO also became the operator of the CSF. The CSF has been in operation since 1986. Recent improvements of the institutional radioactive waste management system in Slovenia are presented in this paper. ARAO has been working on the reestablishment ofmore » institutional radioactive waste management since 1999. The Agency has managed to prepare the most important documents and carry out the basic activities required by the legislation to assure a safe and environmentally acceptable management of the institutional radioactive waste. With the aim to achieve a better organized operational system, ARAO took the advantage of the European Union Transition Facility (EU TF) financing support and applied for the project named 'Improvement of the management of institutional radioactive waste in Slovenia via the design and implementation of an Information Business System'. Through a public invitation for tenders one of the Slovenian largest software company gained the contract. Two international radwaste experts from Belgium were part of their project team. The optimization of the operational system has been carried out in 2007. The project was executed in ten months and it was divided into two phases. The first phase of the project was related with the detection of weaknesses and implementation of the necessary improvements in the current ARAO operational system. With the evaluation of the existing system, possible improvements were identified. In the second phase of the project the software system Information Business System (IBS) was developed and implemented by the group of IT experts. As a software development life-cycle methodology the Waterfall methodology was used. The reason for choosing this methodology lied in its simple approach: analyze the problem, design the solution, implement the code, test the code, integrate and deploy. ARAO's institutional radioactive waste management process was improved in the way that it is more efficient, better organized, allowing traceability and availability of all documents and operational procedures within the field of institutional radioactive waste. The tailored made IBS system links all activities of the institutional radioactive waste management process: collection, transportation, takeover, acceptance, storing, treatment, radiation protection, etc. into one management system. All existing and newly designed evidences, operational procedures and other documents can be searched and viewed via secured Internet access from different locations. (authors)« less

Orbiter Auxiliary Power Unit Flight Support Plan

NASA Technical Reports Server (NTRS)

Guirl, Robert; Munroe, James; Scott, Walter

1990-01-01

This paper discussed the development of an integrated Orbiter Auxiliary Power Unit (APU) and Improved APU (IAPU) Flight Suuport Plan. The plan identifies hardware requirements for continued support of flight activities for the Space Shuttle Orbiter fleet. Each Orbiter vehicle has three APUs that provide power to the hydraulic system for flight control surface actuation, engine gimbaling, landing gear deployment, braking, and steering. The APUs contain hardware that has been found over the course of development and flight history to have operating time and on-vehicle exposure time limits. These APUs will be replaced by IAPUs with enhanced operating lives on a vehicle-by-vehicle basis during scheduled Orbiter modification periods. This Flight Support Plan is used by program management, engineering, logistics, contracts, and procurement groups to establish optimum use of available hardware and replacement quantities and delivery requirements for APUs until vehicle modifications and incorporation of IAPUs. Changes to the flight manifest and program delays are evaluated relative to their impact on hardware availability.

Development and demonstration of a telerobotic excavation system

NASA Technical Reports Server (NTRS)

Burks, Barry L.; Thompson, David H.; Killough, Stephen M.; Dinkins, Marion A.

1994-01-01

Oak Ridge National Laboratory is developing remote excavation technologies for the Department of Energy's Office (DOE) of Technology Development, Robotics Technology Development Program, and also for the Department of Defense (DOD) Project Manager for Ammunition Logistics. This work is being done to meet the need for remote excavation and removal of radioactive and contaminated buried waste at several DOE sites and unexploded ordnance at DOD sites. System requirements are based on the need to uncover and remove waste from burial sites in a way that does not cause unnecessary personnel exposure or additional environmental contamination. Goals for the current project are to demonstrate dexterous control of a backhoe with force feedback and to implement robotic operations that will improve productivity. The Telerobotic Small Emplacement Excavator is a prototype system that incorporates the needed robotic and telerobotic capabilities on a commercially available platform. The ability to add remote dexterous teleoperation and robotic operating modes is intended to be adaptable to other commercially available excavator systems.

Weak annihilation and new physics in charmless [Formula: see text] decays.

PubMed

Bobeth, Christoph; Gorbahn, Martin; Vickers, Stefan

We use currently available data of nonleptonic charmless 2-body [Formula: see text] decays ([Formula: see text]) that are mediated by [Formula: see text] QCD- and QED-penguin operators to study weak annihilation and new-physics effects in the framework of QCD factorization. In particular we introduce one weak-annihilation parameter for decays related by [Formula: see text] quark interchange and test this universality assumption. Within the standard model, the data supports this assumption with the only exceptions in the [Formula: see text] system, which exhibits the well-known "[Formula: see text] puzzle", and some tensions in [Formula: see text]. Beyond the standard model, we simultaneously determine weak-annihilation and new-physics parameters from data, employing model-independent scenarios that address the "[Formula: see text] puzzle", such as QED-penguins and [Formula: see text] current-current operators. We discuss also possibilities that allow further tests of our assumption once improved measurements from LHCb and Belle II become available.

Point-of-care diagnostics: extending the laboratory network to reach the last mile.

PubMed

Drain, Paul K; Rousseau, Christine

2017-03-01

More point-of-care (POC) diagnostic tests are becoming available for HIV diagnosis and treatment in resource-limited settings. These novel technologies have the potential to foster decentralized HIV care and treatment for the benefit of clinical laboratories, HIV clinics, and HIV-infected patients. There continue to be many business, technological, and operational challenges that limit product development and regulatory approval, which limits products available for the required operational and cost-effectiveness studies and delays policy adoption and implementation. Although the rapid HIV diagnostic test has been widely successful, the pathways for POC CD4 cell count and HIV viral load assay analyzers have been more challenging. We describe significant hurdles for product development, approval, and implementation, which include the business case, technical development, clinical impact, and integrating laboratory and clinical networks. The objective of this review is to highlight the obstacles for developing and implementing appropriate strategies for POC HIV testing assays to improve the clinical services for HIV-infected patients in resource-limited settings.

ADAMS: AIRLAB data management system user's guide

NASA Technical Reports Server (NTRS)

Conrad, C. L.; Ingogly, W. F.; Lauterbach, L. A.

1986-01-01

The AIRLAB Data Management System (ADAMS) is an online environment that supports research at NASA's AIRLAB. ADAMS provides an easy to use interactive interface that eases the task of documenting and managing information about experiments and improves communication among project members. Data managed by ADAMS includes information about experiments, data sets produced, software and hardware available in AIRLAB as well as that used in a particular experiment, and an on-line engineer's notebook. The User's Guide provides an overview of the ADAMS system as well as details of the operations available within ADAMS. A tutorial section takes the user step-by-step through a typical ADAMS session. ADAMS runs under the VAX/VMS operating system and uses the ORACLE database management system and DEC/FMS (the Forms Management System). ADAMS can be run from any VAX connected via DECnet to the ORACLE host VAX. The ADAMS system is designed for simplicity, so interactions within the underlying data management system and communications network are hidden from the user.

Rectus abdominus fascial sheath usage for crural reinforcement during surgical management of GERD: preliminary report of a prospective randomized clinical trial.

PubMed

Yigit, Taner; Coskun, Ali Kagan; Sinan, Huseyin; Harlak, Ali; Kantarcioglu, Murat; Kilbas, Zafer; Kozak, Orhan; Cetiner, Sadettin

2012-08-01

Many materials are currently being used to reinforce the crural repair. Perforation, intensive fibrosis, and price are limiting the usage of these materials. Our purpose was to seek an alternative, cheap, always available, and inert material to use for cruroplasty reinforcement. Twenty-four patients participated and were randomly divided into 2 groups (graft+laparoscopic Nissen fundoplication and laparoscopic Nissen fundoplication alone) with 12 patients in each group. Total operation time, postoperative dysphagia rate, dysphagia improvement time, postoperative pain, recurrence, and incisional hernia rate were compared. There was no difference in terms of study parameters between both groups except for the mean operation time. Autograft hiatoplasty seems to be a good alternative for crural reinforcement. It provides safe reinforcement, has the same dysphagia rates as meshless hiatoplasty, and avoids potential complications of redo surgery by minimizing extensive fibrosis. Furthermore, the rectus abdominus sheath is always available and inexpensive.

Benefits of Sharing Information: Supermodel Ensemble and Applications in South America

NASA Astrophysics Data System (ADS)

Dias, P. L.

2006-05-01

A model intercomparison program involving a large number of academic and operational institutions has been implemented in South America since 2003, motivated by the SALLJEX Intercomparison Program in 2003 (a research program focused on the identification of the role of the Andes low level jet moisture transport from the Amazon to the Plata basin) and the WMO/THORPEX (www.wmo.int/thorpex) goals to improve predictability through the proper combination of numerical weather forecasts. This program also explores the potential predictability associated with the combination of a large number of possible scenarios in the time scale of a few days to up to 15 days. Five academic institutions and five operational forecasting centers in several countries in South America, 1 academic institution in the USA, and the main global forecasting centers (NCEP, UKMO, ECMWF) agreed to provide numerical products based on operational and experimental models. The metric for model validation is concentrated on the fit of the forecast to surface observations. Meteorological data from airports, synoptic stations operated by national weather services, automatic data platforms maintained by different institutions, the PIRATA buoys etc are all collected through LDM/NCAR or direct transmission. Approximately 40 models outputs are available on a daily basis, twice a day. A simple procedure based on data assimilation principles was quite successful in combining the available forecasts in order to produce temperature, dew point, wind, pressure and precipitation forecasts at station points in S. America. The procedure is based on removing each model bias at the observational point and a weighted average based on the mean square error of the forecasts. The base period for estimating the bias and mean square error is of the order of 15 to 30 days. Products of the intercomparison model program and the optimal statistical combination of the available forecasts are public and available in real time (www.master.iag.usp.br/). Monitoring of the use of the products reveal a growing trend in the last year (reaching about 10.000 accesses per day in recent months). The intercomparison program provides a rich data set for educational products (real time use in Synoptic Meteorology and Numerical Weather Forecasting lectures), operational weather forecasts in national or regional weather centers and for research purposes. During the first phase of the program it was difficult to convince potential participants to share the information in the public homepage. However, as the system evolved, more and more institutions became associated with the program. The general opinion of the participants is that the system provides an unified metric for evaluation, a forum for discussion of the physical origin of the model forecast differences and therefore improvement of the quality of the numerical guidance.

Advanced light source technologies that enable high-volume manufacturing of DUV lithography extensions

NASA Astrophysics Data System (ADS)

Cacouris, Theodore; Rao, Rajasekhar; Rokitski, Rostislav; Jiang, Rui; Melchior, John; Burfeindt, Bernd; O'Brien, Kevin

2012-03-01

Deep UV (DUV) lithography is being applied to pattern increasingly finer geometries, leading to solutions like double- and multiple-patterning. Such process complexities lead to higher costs due to the increasing number of steps required to produce the desired results. One of the consequences is that the lithography equipment needs to provide higher operating efficiencies to minimize the cost increases, especially for producers of memory devices that experience a rapid decline in sales prices of these products over time. In addition to having introduced higher power 193nm light sources to enable higher throughput, we previously described technologies that also enable: higher tool availability via advanced discharge chamber gas management algorithms; improved process monitoring via enhanced on-board beam metrology; and increased depth of focus (DOF) via light source bandwidth modulation. In this paper we will report on the field performance of these technologies with data that supports the desired improvements in on-wafer performance and operational efficiencies.

Very high-current-density Nb/AlN/Nb tunnel junctions for low-noise submillimeter mixers

NASA Astrophysics Data System (ADS)

Kawamura, Jonathan; Miller, David; Chen, Jian; Zmuidzinas, Jonas; Bumble, Bruce; LeDuc, Henry G.; Stern, Jeff A.

2000-04-01

We have fabricated and tested submillimeter-wave superconductor-insulator-superconductor (SIS) mixers using very high-current-density Nb/AlN/Nb tunnel junctions (Jc≈30 kA cm-2). The junctions have low-resistance-area products (RNA≈5.6 Ω μm2), good subgap-to-normal resistance ratios Rsg/RN≈10, and good run-to-run reproducibility. From Fourier transform spectrometer measurements, we infer that ωRNC=1 at 270 GHz. This is a factor of 2.5 improvement over what is generally available with Nb/AlOx/Nb junctions suitable for low-noise mixers. The AlN-barrier junctions are indeed capable of low-noise operation: we measure an uncorrected double-sideband receiver noise temperature of TRX=110 K at 533 GHz for an unoptimized device. In addition to providing wider bandwidth operation at lower frequencies, the AlN-barrier junctions will considerably improve the performance of THz SIS mixers by reducing rf loss in the tuning circuits.

Learning and tuning fuzzy logic controllers through reinforcements

NASA Technical Reports Server (NTRS)

Berenji, Hamid R.; Khedkar, Pratap

1992-01-01

A new method for learning and tuning a fuzzy logic controller based on reinforcements from a dynamic system is presented. In particular, our Generalized Approximate Reasoning-based Intelligent Control (GARIC) architecture: (1) learns and tunes a fuzzy logic controller even when only weak reinforcements, such as a binary failure signal, is available; (2) introduces a new conjunction operator in computing the rule strengths of fuzzy control rules; (3) introduces a new localized mean of maximum (LMOM) method in combining the conclusions of several firing control rules; and (4) learns to produce real-valued control actions. Learning is achieved by integrating fuzzy inference into a feedforward network, which can then adaptively improve performance by using gradient descent methods. We extend the AHC algorithm of Barto, Sutton, and Anderson to include the prior control knowledge of human operators. The GARIC architecture is applied to a cart-pole balancing system and has demonstrated significant improvements in terms of the speed of learning and robustness to changes in the dynamic system's parameters over previous schemes for cart-pole balancing.

OPAD-EDIFIS Real-Time Processing

NASA Technical Reports Server (NTRS)

Katsinis, Constantine

1997-01-01

The Optical Plume Anomaly Detection (OPAD) detects engine hardware degradation of flight vehicles through identification and quantification of elemental species found in the plume by analyzing the plume emission spectra in a real-time mode. Real-time performance of OPAD relies on extensive software which must report metal amounts in the plume faster than once every 0.5 sec. OPAD software previously written by NASA scientists performed most necessary functions at speeds which were far below what is needed for real-time operation. The research presented in this report improved the execution speed of the software by optimizing the code without changing the algorithms and converting it into a parallelized form which is executed in a shared-memory multiprocessor system. The resulting code was subjected to extensive timing analysis. The report also provides suggestions for further performance improvement by (1) identifying areas of algorithm optimization, (2) recommending commercially available multiprocessor architectures and operating systems to support real-time execution and (3) presenting an initial study of fault-tolerance requirements.

Nuclear Engine System Simulation (NESS). Version 2.0: Program user's guide

NASA Technical Reports Server (NTRS)

Pelaccio, Dennis G.; Scheil, Christine M.; Petrosky, Lyman

1993-01-01

This Program User's Guide discusses the Nuclear Thermal Propulsion (NTP) engine system design features and capabilities modeled in the Nuclear Engine System Simulation (NESS): Version 2.0 program (referred to as NESS throughout the remainder of this document), as well as its operation. NESS was upgraded to include many new modeling capabilities not available in the original version delivered to NASA LeRC in Dec. 1991, NESS's new features include the following: (1) an improved input format; (2) an advanced solid-core NERVA-type reactor system model (ENABLER 2); (3) a bleed-cycle engine system option; (4) an axial-turbopump design option; (5) an automated pump-out turbopump assembly sizing option; (6) an off-design gas generator engine cycle design option; (7) updated hydrogen properties; (8) an improved output format; and (9) personal computer operation capability. Sample design cases are presented in the user's guide that demonstrate many of the new features associated with this upgraded version of NESS, as well as design modeling features associated with the original version of NESS.

Building a new space weather facility at the National Observatory of Athens

NASA Astrophysics Data System (ADS)

Kontogiannis, Ioannis; Belehaki, Anna; Tsiropoula, Georgia; Tsagouri, Ioanna; Anastasiadis, Anastasios; Papaioannou, Athanasios

2016-01-01

The PROTEAS project has been initiated at the Institute of Astronomy, Astrophysics, Space Applications and Remote Sensing (IAASARS) of the National Observatory of Athens (NOA). One of its main objectives is to provide observations, processed data and space weather nowcasting and forecasting products, designed to support the space weather research community and operators of commercial and industrial systems. The space weather products to be released by this facility, will be the result of the exploitation of ground-based, as well as space-borne observations and of model results and tools already available or under development by IAASARS researchers. The objective will be achieved through: (a) the operation of a small full-disk solar telescope to conduct regular observations of the Sun in the H-alpha line; (b) the construction of a database with near real-time solar observations which will be available to the community through a web-based facility (HELIOSERVER); (c) the development of a tool for forecasting Solar Energetic Particle (SEP) events in relation to observed solar eruptive events; (d) the upgrade of the Athens Digisonde with digital transceivers and the capability of operating in bi-static link mode and (e) the sustainable operation of the European Digital Upper Atmosphere Server (DIAS) upgraded with additional data sets integrated in an interface with the HELIOSERVER and with improved models for the real-time quantification of the effects of solar eruptive events in the ionosphere.

Towards Large-area Field-scale Operational Evapotranspiration for Water Use Mapping

NASA Astrophysics Data System (ADS)

Senay, G. B.; Friedrichs, M.; Morton, C.; Huntington, J. L.; Verdin, J.

2017-12-01

Field-scale evapotranspiration (ET) estimates are needed for improving surface and groundwater use and water budget studies. Ideally, field-scale ET estimates would be at regional to national levels and cover long time periods. As a result of large data storage and computational requirements associated with processing field-scale satellite imagery such as Landsat, numerous challenges remain to develop operational ET estimates over large areas for detailed water use and availability studies. However, the combination of new science, data availability, and cloud computing technology is enabling unprecedented capabilities for ET mapping. To demonstrate this capability, we used Google's Earth Engine cloud computing platform to create nationwide annual ET estimates with 30-meter resolution Landsat ( 16,000 images) and gridded weather data using the Operational Simplified Surface Energy Balance (SSEBop) model in support of the National Water Census, a USGS research program designed to build decision support capacity for water management agencies and other natural resource managers. By leveraging Google's Earth Engine Application Programming Interface (API) and developing software in a collaborative, open-platform environment, we rapidly advance from research towards applications for large-area field-scale ET mapping. Cloud computing of the Landsat image archive combined with other satellite, climate, and weather data, is creating never imagined opportunities for assessing ET model behavior and uncertainty, and ultimately providing the ability for more robust operational monitoring and assessment of water use at field-scales.

The ophthalmic implications of the correction of late enophthalmos following severe midfacial trauma.

PubMed Central

Iliff, N T

1991-01-01

Severe midfacial trauma presents several challenges to the reconstructive surgeon. Acute rigid fixation of the facial skeleton accompanied by bone grafting to restore the confines and volume of the orbit provide the best opportunity for acceptable aesthetic results. The severity of the trauma causes the late postoperative complication of enophthalmos. Injury to orbital structures with subsequent cicatricial change results in significant alteration in extraocular motility with resultant diplopia. There are no reports in the literature which critically evaluate the effect of late enophthalmos correction on extraocular motility, diplopia, and vision in patients who have suffered Le Fort or NOE fractures. A retrospective study is presented which reviews the results of late surgery for the correction of enophthalmos in 40 patients, all of whom had severe "impure" orbital fractures. This study addresses the following questions: (1) Can the globe effectively be repositioned?, (2) Is there a change in subjective diplopia?, (3) Does a change in extraocular motility occur, and if it does, is it predictable?, (4) Is there a risk to visual acuity? and finally, (5) Do the answers to questions 1 through 4 suggest that late surgical intervention for the correction of enophthalmos should be recommended for this patient population? During a 9-year period, 44 patients with severe diplopia trauma received surgery for enophthalmos correction. A review of 40 patients on whom 56 operations were performed is presented. Thirty-eight patients had enophthalmos and 35 had inferior displacement of the globe. Medial displacement of the globe occurred in 11 patients. Twenty-nine patients had diplopia. Six patients had vision too poor on the injured side to have diplopia. Enophthalmos was improved in 32 patients. Dystopia of the globe was improved in 31 cases. However, neither enophthalmos nor dystopia of the globe could be improved with every operation. Only 35 of the 48 operations for enophthalmos for which measurements were available produced an improvement; in 1 case the enophthalmos was thought to be worse postoperatively. Dystopia operations resulted in improvement in 40 of 48 operations; in 2 instances dystopia was worse postoperatively. Diplopia was unchanged by 33 operations, improved by 11 procedures, and worsened by 6. If patients are considered before and after their total reconstruction course, diplopia was improved in 9 of the 29 patients. In seven of these nine, diplopia was eliminated. There was no change in or production of diplopia in 19 patients, and 5 patients had worsening of their double vision.(ABSTRACT TRUNCATED AT 400 WORDS) Images FIGURE 4 FIGURE 5 FIGURE 6 FIGURE 7 FIGURE 8 FIGURE 9 FIGURE 16 FIGURE 17 FIGURE 18 FIGURE 19 FIGURE 20 FIGURE20 FIGURE 20 FIGURE 22 FIGURE 23 PMID:1808816

Alarms Philosophy

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, Karen S; Kasemir, Kay

2009-01-01

An effective alarm system consists of a mechanism to monitor control points and generate alarm notifications, tools for operators to view, hear, acknowledge and handle alarms and a good configuration. Despite the availability of numerous fully featured tools, accelerator alarm systems continue to be disappointing to operations, frequently to the point of alarms being permanently silenced or totally ignored. This is often due to configurations that produce an excessive number of alarms or fail to communicate the required operator response. Most accelerator controls systems do a good job of monitoring specified points and generating notifications when parameters exceed predefined limits.more » In some cases, improved tools can help, but more often, poor configuration is the root cause of ineffective alarm systems. A SNS, we have invested considerable effort in generating appropriate configurations using a rigorous set of rules based on best practices in the industrial process controls community. This paper will discuss our alarm configuration philosophy and operator response to our new system.« less

Temperature Effects in Varactors and Multipliers

NASA Technical Reports Server (NTRS)

East, J.; Mehdi, Imran

2001-01-01

Varactor diode multipliers are a critical part of many THz measurement systems. The power and efficiencies of these devices limit the available power for THz sources. Varactor operation is determined by the physics of the varactor device and a careful doping profile design is needed to optimize the performance. Higher doped devices are limited by junction breakdown and lower doped structures are limited by current saturation. Higher doped structures typically have higher efficiencies and lower doped structures typically have higher powers at the same operating frequency and impedance level. However, the device material properties are also a function of the operating temperature. Recent experimental evidence has shown that the power output of a multiplier can be improved by cooling the device. We have used a particle Monte Carlo simulation to investigate the temperature dependent velocity vs. electric field in GaAs. This information was then included in a nonlinear device circuit simulator to predict multiplier performance for various temperatures and device designs. This paper will describe the results of this analysis of temperature dependent multiplier operation.

System to improve the Understanding of Collected Logistic Data, to Optimize Cycle-Time and Delivery Performance

NASA Astrophysics Data System (ADS)

van Rooijen, Wim-Jan; Rodriguez, Ben

2002-12-01

A complex production mask-house faces the issue of handling and understanding the logistics information from the production process of the masks. We managed to control key performance indicators like cycle-time, flow-factor, line-speed, WIP, etc. To improve the line flow, we set-up rules for optimising batching at operations and forbid batching between operations, we defined maximum and minimum WIP at the operations, scheduled urgency of the different lots and built rules for bottleneck management. Also we restricted the number of "hot lots". By migrating to the modern MES (manufacturing execution system) MaTISSe, which manages the shopfloor control, and a reporting database, we are able to eliminate the time deviations within our data, caused by data-extraction for different reports at different moments. This gives us a better understanding of our fixed bottleneck and a faster recognition of the temporarily bottlenecks caused by missing availability of machines or men. In this paper we describe the features and advantages of our new MES, as well as the migration process. We have already achieved considerable benefits. Our plan is to extend decision support within the MES, to help both managers and operators to make the right decisions. The project behind this paper reaped major benefits described here and we are looking forward to further challenges and successes.

FRACTAL Systems & Project suite: engineering tools for improving development and operation of the systems

NASA Astrophysics Data System (ADS)

Pérez-Calpena, A.; Mujica-Alvarez, E.; Osinde-Lopez, J.; García-Vargas, M.

2008-07-01

This paper describes the FRACTAL Systems & Projects suite. This suite is composed by several tools (GECO, DOCMA and SUMO) that provide the capabilities that all organizations need to store and manage the system information generated along the project's lifetime, from the design phase to the operation phase. The amount of information that is generated in a project keeps growing in size and complexity along the project's lifetime, to an extent that it becomes impossible to manage it without the aid of specific computer-based tools. The suite described in this paper is the solution developed by FRACTAL to assist the execution of different scientific projects, mainly related with telescopes and instruments, for astronomical research centres. These tools help the system and project engineers to maintain the technical control of the systems and to ensure an optimal use of the resources. GECO eases the control of the system configuration data; DOCMA provides the means to organise and manage the documents generated in the project; SUMO allows managing and scheduling the operation, the maintenance activities and the resources during the operational phase of a system. These tools improve the project communication making the information available to the authorized users (project team, customers, Consortium's members, etc). Finally and depending on the project needs, these three tools can be used integrated or in an independent manner.

Reliability and availability analysis of a 10 kW@20 K helium refrigerator

NASA Astrophysics Data System (ADS)

Li, J.; Xiong, L. Y.; Liu, L. Q.; Wang, H. R.; Wang, B. M.

2017-02-01

A 10 kW@20 K helium refrigerator has been established in the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. To evaluate and improve this refrigerator’s reliability and availability, a reliability and availability analysis is performed. According to the mission profile of this refrigerator, a functional analysis is performed. The failure data of the refrigerator components are collected and failure rate distributions are fitted by software Weibull++ V10.0. A Failure Modes, Effects & Criticality Analysis (FMECA) is performed and the critical components with higher risks are pointed out. Software BlockSim V9.0 is used to calculate the reliability and the availability of this refrigerator. The result indicates that compressors, turbine and vacuum pump are the critical components and the key units of this refrigerator. The mitigation actions with respect to design, testing, maintenance and operation are proposed to decrease those major and medium risks.

Stochastic availability analysis of operational data systems in the Deep Space Network

NASA Technical Reports Server (NTRS)

Issa, T. N.

1991-01-01

Existing availability models of standby redundant systems consider only an operator's performance and its interaction with the hardware performance. In the case of operational data systems in the Deep Space Network (DSN), in addition to an operator system interface, a controller reconfigures the system and links a standby unit into the network data path upon failure of the operating unit. A stochastic (Markovian) process technique is used to model and analyze the availability performance and occurrence of degradation due to partial failures are quantitatively incorporated into the model. Exact expressions of the steady state availability and proportion degraded performance measures are derived for the systems under study. The interaction among the hardware, operator, and controller performance parameters and that interaction's effect on data availability are evaluated and illustrated for an operational data processing system.

Improving online risk assessment with equipment prognostics and health monitoring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coble, Jamie B.; Liu, Xiaotong; Briere, Chris

The current approach to evaluating the risk of nuclear power plant (NPP) operation relies on static probabilities of component failure, which are based on industry experience with the existing fleet of nominally similar light water reactors (LWRs). As the nuclear industry looks to advanced reactor designs that feature non-light water coolants (e.g., liquid metal, high temperature gas, molten salt), this operating history is not available. Many advanced reactor designs use advanced components, such as electromagnetic pumps, that have not been used in the US commercial nuclear fleet. Given the lack of rich operating experience, we cannot accurately estimate the evolvingmore » probability of failure for basic components to populate the fault trees and event trees that typically comprise probabilistic risk assessment (PRA) models. Online equipment prognostics and health management (PHM) technologies can bridge this gap to estimate the failure probabilities for components under operation. The enhanced risk monitor (ERM) incorporates equipment condition assessment into the existing PRA and risk monitor framework to provide accurate and timely estimates of operational risk.« less

Working session 5: Operational aspects and risk analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cizelj, L.; Donoghue, J.

1997-02-01

A general observation is that both operational aspects and risk analysis cannot be adequately discussed without information presented in other sessions. Some overlap of conclusions and recommendations is therefore to be expected. Further, it was assumed that recommendations concerning improvements in some related topics were generated by other sessions and are not repeated here. These include: (1) Knowledge on degradation mechanisms (initiation, progression, and failure). (2) Modeling of degradation (initiation, progression, and failure). (3) Capabilities of NDE methods. (4) Preventive maintenance and repair. One should note here, however, that all of these directly affect both operational and risk aspects ofmore » affected plants. A list of conclusions and recommendations is based on available presentations and discussions addressing risk and operational experience. The authors aimed at reaching as broad a consensus as possible. It should be noted here that there is no strict delineation between operational and safety aspects of degradation of steam generator tubes. This is caused by different risk perceptions in different countries/societies. The conclusions and recommendations were divided into four broad groups: human reliability; leakage monitoring; risk impact; and consequence assessment.« less

Assessing the operation rules of a reservoir system based on a detailed modelling-chain

NASA Astrophysics Data System (ADS)

Bruwier, M.; Erpicum, S.; Pirotton, M.; Archambeau, P.; Dewals, B.

2014-09-01

According to available climate change scenarios for Belgium, drier summers and wetter winters are expected. In this study, we focus on two muti-purpose reservoirs located in the Vesdre catchment, which is part of the Meuse basin. The current operation rules of the reservoirs are first analysed. Next, the impacts of two climate change scenarios are assessed and enhanced operation rules are proposed to mitigate these impacts. For this purpose, an integrated model of the catchment was used. It includes a hydrological model, one-dimensional and two-dimensional hydraulic models of the river and its main tributaries, a model of the reservoir system and a flood damage model. Five performance indicators of the reservoir system have been defined, reflecting its ability to provide sufficient drinking, to control floods, to produce hydropower and to reduce low-flow condition. As shown by the results, enhanced operation rules may improve the drinking water potential and the low-flow augmentation while the existing operation rules are efficient for flood control and for hydropower production.

Assessing the operation rules of a reservoir system based on a detailed modelling chain

NASA Astrophysics Data System (ADS)

Bruwier, M.; Erpicum, S.; Pirotton, M.; Archambeau, P.; Dewals, B. J.

2015-03-01

According to available climate change scenarios for Belgium, drier summers and wetter winters are expected. In this study, we focus on two multi-purpose reservoirs located in the Vesdre catchment, which is part of the Meuse basin. The current operation rules of the reservoirs are first analysed. Next, the impacts of two climate change scenarios are assessed and enhanced operation rules are proposed to mitigate these impacts. For this purpose, an integrated model of the catchment was used. It includes a hydrological model, one-dimensional and two-dimensional hydraulic models of the river and its main tributaries, a model of the reservoir system and a flood damage model. Five performance indicators of the reservoir system have been defined, reflecting its ability to provide sufficient drinking water, to control floods, to produce hydropower and to reduce low-flow conditions. As shown by the results, enhanced operation rules may improve the drinking water potential and the low-flow augmentation while the existing operation rules are efficient for flood control and for hydropower production.

Comparison of Fluoroplastic Causse Loop Piston and Titanium Soft-Clip in Stapedotomy

PubMed Central

Faramarzi, Mohammad; Gilanifar, Nafiseh; Roosta, Sareh

2017-01-01

Introduction: Different types of prosthesis are available for stapes replacement. Because there has been no published report on the efficacy of the titanium soft-clip vs the fluoroplastic Causse loop Teflon piston, we compared short-term hearing results of both types of prosthesis in patients who underwent stapedotomy due to otosclerosis. Materials and Methods: A total of 57 ears were included in the soft-clip group and 63 ears were included in the Teflon-piston group. Pre-operative and post-operative air conduction, bone conduction, air-bone gaps, speech discrimination score, and speech reception thresholds were analyzed. Results: Post-operative speech reception threshold gains did not differ significantly between the two groups (P=0.919). However, better post-operative air-bone gap improvement at low frequencies was observed in the Teflon-piston group over the short-term follow-up (at frequencies of 0.25 and 0.50 kHz; P=0.007 and P=0.001, respectively). Conclusion: Similar post-operative hearing results were observed in the two groups in the short-term. PMID:28229059

The benefit of using additional hydrological information from earth observations and reanalysis data on water allocation decisions in irrigation districts

NASA Astrophysics Data System (ADS)

Kaune, Alexander; López, Patricia; Werner, Micha; de Fraiture, Charlotte

2017-04-01

Hydrological information on water availability and demand is vital for sound water allocation decisions in irrigation districts, particularly in times of water scarcity. However, sub-optimal water allocation decisions are often taken with incomplete hydrological information, which may lead to agricultural production loss. In this study we evaluate the benefit of additional hydrological information from earth observations and reanalysis data in supporting decisions in irrigation districts. Current water allocation decisions were emulated through heuristic operational rules for water scarce and water abundant conditions in the selected irrigation districts. The Dynamic Water Balance Model based on the Budyko framework was forced with precipitation datasets from interpolated ground measurements, remote sensing and reanalysis data, to determine the water availability for irrigation. Irrigation demands were estimated based on estimates of potential evapotranspiration and coefficient for crops grown, adjusted with the interpolated precipitation data. Decisions made using both current and additional hydrological information were evaluated through the rate at which sub-optimal decisions were made. The decisions made using an amended set of decision rules that benefit from additional information on demand in the districts were also evaluated. Results show that sub-optimal decisions can be reduced in the planning phase through improved estimates of water availability. Where there are reliable observations of water availability through gauging stations, the benefit of the improved precipitation data is found in the improved estimates of demand, equally leading to a reduction of sub-optimal decisions.

Methylation polymorphism influences practice effects in children during attention tasks1

PubMed Central

Voelker, Pascale; Sheese, Brad E.; Rothbart, Mary K.; Posner, Michael I.

2017-01-01

Epigenetic mechanisms mediate the influence of experience on gene expression. Methylation is a principal method for inducing epigenetic effects on DNA. In this paper, we examine alleles of the methylenetetrahydrofolate reductase (MTHFR) gene that vary enzyme activity, altering the availability of the methyl donor and thus changing the efficiency of methylation. We hypothesized that alleles of the MTHFR gene would influence behavior in an attention related task in conjunction with genes known to influence attention. We found that 7-year-old children homozygous for the C allele of MTHFR in interaction with the catechol O-methyltransferase (COMT) gene showed greater improvement in overall reaction time (RT) and in conflict resolution with practice on the Attention Network Test (ANT). This finding indicates that methylation may operate on or through genes that influence executive network operation. However, MTHFR T allele carriers showed faster overall RT and conflict resolution. Some children showed an initial improvement in ANT RT followed by a decline in performance, and we found that alleles of the dopamine beta-hydroxylase (DBH) gene were related to this performance decline. These results suggest a genetic dissociation between improvement while learning a skill and reduction in performance with continued practice. PMID:27050482

Evaluation of low-cost commercial-off-the-shelf autopilot systems for SUAS operations

NASA Astrophysics Data System (ADS)

Brown, Calvin Thomas

With this increase in unmanned aircraft system (UAS) operations, there is a need for a structured process to evaluate different commercially available systems, particularly autopilots. The Remotely Operated Aircraft Management, Interpretation, and Navigation from Ground or ROAMING scale was developed to meet this need. This scale is a modification of the widely accepted Handling Qualities Rating scale developed by George Cooper and Robert Harper Jr. The Cooper-Harper scale allows pilots to rate a vehicle's performance in completing some task. Similarly, the ROAMING scale allows UAS operators to evaluate the management and observability of UAS in completing some task. The standardized evaluative process consists of cost, size, weight, and power (SWAP) analysis, ease of implementation through procedural description of setup, ROAMING scale rating, a slightly modified NASA TLX rating, and comparison of manual operation to autonomous operation of the task. This standard for evaluation of autopilots and their software will lead to better understanding of the workload placed on UAS operators and indicate where improvements to design and operational procedures can be made. An assortment of low-cost commercial-off-the-shelf (COTS) autopilots were selected for use in the development of the evaluation and results of these tests demonstrate the commonalities and differences in these systems.

Chiller Controls-related Energy Saving Opportunities in FederalFacilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Webster, Tom

2003-01-01

Chillers are a significant component of large facility energy use. The focus of much of the development of chilled water systems in recent years has been on optimization of set point and staging controls, improvements in chiller design to increase efficiency and accommodate chlorofluorocarbon (CFC) refrigerant replacements. Other improvements have been made by upgrading controls to the latest digital technologies, improving access and monitoring via communications and sophisticated liquid crystal displays (LCD), more robust fault diagnostics and operating and maintenance information logging. Advances have also been made in how chiller plant systems are designed and operated, and in the diversitymore » of chiller products that are available to support innovative approaches. As in many industries, these improvements have been facilitated by advances in, and lower costs for, enabling technologies, such as refrigerants, compressor design, electronics for controls and variable frequency drives (VFD). Along with the improvements in electronics one would expect that advances have also been made in the functionality of unit controls included with chillers. Originally, the primary purpose of this project was to investigate the state of practice of chiller unit controllers in terms of their energy saving capabilities. However, early in the study it was discovered that advances in this area did not include incorporation of significantly different capabilities than had existed 10-15 years ago. Thus the scope has been modified to provide an overview of some of the basic controls-related energy saving strategies that are currently available along with guideline estimates of their potential and applicability. We have minimized consideration of strategies that could be primarily implemented via design practices such as chiller selection and plant design, and those that can only be implemented by a building management system (BMS). Also, since most of the floor space of federal buildings occurs in large buildings, we have focused on water-cooled screw and centrifugal chillers of 100 ton capacity and greater. However, the role of reciprocating and gas chillers (absorption and engine driven) is discussed briefly. Understanding the demographics of chiller deployment in the federal sector, state of practice of energy savings strategies and control features availability will help federal energy managers and program implementers to make informed decisions in support of energy saving performance contracting (ESPC) and other programs.« less

Improving operating room safety

PubMed Central

2009-01-01

Despite the introduction of the Universal Protocol, patient safety in surgery remains a daily challenge in the operating room. This present study describes one community health system's efforts to improve operating room safety through human factors training and ultimately the development of a surgical checklist. Using a combination of formal training, local studies documenting operating room safety issues and peer to peer mentoring we were able to substantially change the culture of our operating room. Our efforts have prepared us for successfully implementing a standardized checklist to improve operating room safety throughout our entire system. Based on these findings we recommend a multimodal approach to improving operating room safety. PMID:19930577

Improving Minimally Invasive Adrenalectomy: Selection of Optimal Approach and Comparison of Outcomes.

PubMed

Lairmore, Terry C; Folek, Jessica; Govednik, Cara M; Snyder, Samuel K

2016-07-01

Minimally invasive adrenalectomy is commonly performed by either a transperitoneal laparoscopic (TLA) or posterior retroperitoneoscopic (PRA) approach. Our group described the technique for robot-assisted PRA (RAPRA) in 2010. Few studies are available that directly compare outcomes between the available operative approaches. We reviewed our results for minimally invasive adrenalectomy using the three different approaches over a 10-year period. Between January 2005 and April 2015, 160 minimally invasive adrenalectomies were performed. Clinicopathologic data were prospectively collected and retrospectively analyzed. The primary endpoints evaluated were operative time, blood loss, length of stay (LOS), and morbidity. The study included 67 TLA, 76 PRA, and 17 RAPRA procedures. Tumor size for PRA/RAPRA was smaller than for patients undergoing TLA (2.38 vs 3.6 cm, p ≤ 0.0001). Procedure time was shorter for PRA versus TLA (133.3 vs 152.8 min, p = 0.0381), as was LOS (1.85 vs 2.82 days, p = 0.0145). Procedure time was longer in RAPRA versus TLA/PRA (177 vs 153/133 min, p = 0.008), but LOS was significantly decreased (1.53 vs 2.82/1.85 days, p = 0.004). Minimally invasive adrenalectomy is associated with expected excellent outcomes regardless of approach. In our series, the posterior approach is associated with decreased operative time and LOS. Robotic technology provides potential advantages for the surgeon at the expense of more complex setup requirements and costs. Further study is required to demonstrate clear benefit of one surgical approach. Utilization of the entire spectrum of available operative techniques can allow for selection of the optimal approach based on individual patient factors.

How to keep the Grid full and working with ATLAS production and physics jobs

NASA Astrophysics Data System (ADS)

Pacheco Pagés, A.; Barreiro Megino, F. H.; Cameron, D.; Fassi, F.; Filipcic, A.; Di Girolamo, A.; González de la Hoz, S.; Glushkov, I.; Maeno, T.; Walker, R.; Yang, W.; ATLAS Collaboration

2017-10-01

The ATLAS production system provides the infrastructure to process millions of events collected during the LHC Run 1 and the first two years of Run 2 using grid, clouds and high performance computing. We address in this contribution the strategies and improvements that have been implemented to the production system for optimal performance and to achieve the highest efficiency of available resources from operational perspective. We focus on the recent developments.

The Importance of Human Reliability Analysis in Human Space Flight: Understanding the Risks

NASA Technical Reports Server (NTRS)

Hamlin, Teri L.

2010-01-01

HRA is a method used to describe, qualitatively and quantitatively, the occurrence of human failures in the operation of complex systems that affect availability and reliability. Modeling human actions with their corresponding failure in a PRA (Probabilistic Risk Assessment) provides a more complete picture of the risk and risk contributions. A high quality HRA can provide valuable information on potential areas for improvement, including training, procedural, equipment design and need for automation.

I need to know! Timely accessing of perioperative user manuals.

PubMed

Landreneau, Raphael

2010-12-01

Ready access to equipment or product information is essential for the safe operation of the many items that a perioperative nurse is asked to use, troubleshoot, or maintain. One institution's solution for making manufacturer information available in the practice setting was to create a facility intranet site dedicated to OR equipment manuals. This site provides information access to perioperative nurses and support staff members and, ultimately, helps improve patient care. Published by Elsevier Inc. All rights reserved.

Improving the Analysis Capabilities of the Synthetic Theater Operations Research Model (STORM)

DTIC Science & Technology

2014-09-01

course of action CSG carrier strike group DMSO defense modeling and simulation DOD Department of Defense DOE design of experiments ESG...development of an overall objective or end-state; a ways ( courses of action); and a means (available resources). STORM is a campaign analysis tool that...refers to the courses of action (COA) that are carefully planned out in advance by individuals relevant to a specific campaign (such as N81). For

Design of Multi-Order Diffractive THz Lenses

DTIC Science & Technology

2012-09-23

surface. This makes the fabrication process easier and more accurate, thereby improving optical quality. A CNC lathe can be used to carve the lens out...for low-end THz operation (200-800 GHz). The lens was fabricated in Teflon with a small CNC lathe and can be seen in Fig. 3. With only 4 zones...excellent THz transparency and is readily available. Once the CNC turning was complete, the lens was separated from its substrate with a band-saw and

Time-Critical Database Conditions Data-Handling for the CMS Experiment

NASA Astrophysics Data System (ADS)

De Gruttola, Michele; Di Guida, Salvatore; Innocente, Vincenzo; Pierro, Antonio

2011-08-01

Automatic, synchronous and of course reliable population of the condition database is critical for the correct operation of the online selection as well as of the offline reconstruction and data analysis. We will describe here the system put in place in the CMS experiment to automate the processes to populate centrally the database and make condition data promptly available both online for the high-level trigger and offline for reconstruction. The data are “dropped” by the users in a dedicated service which synchronizes them and takes care of writing them into the online database. Then they are automatically streamed to the offline database, hence immediately accessible offline worldwide. This mechanism was intensively used during 2008 and 2009 operation with cosmic ray challenges and first LHC collision data, and many improvements were done so far. The experience of this first years of operation will be discussed in detail.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flory, John Andrew; Padilla, Denise D.; Gauthier, John H.

Upcoming weapon programs require an aggressive increase in Application Specific Integrated Circuit (ASIC) production at Sandia National Laboratories (SNL). SNL has developed unique modeling and optimization tools that have been instrumental in improving ASIC production productivity and efficiency, identifying optimal operational and tactical execution plans under resource constraints, and providing confidence in successful mission execution. With ten products and unprecedented levels of demand, a single set of shared resources, highly variable processes, and the need for external supplier task synchronization, scheduling is an integral part of successful manufacturing. The scheduler uses an iterative multi-objective genetic algorithm and a multi-dimensional performancemore » evaluator. Schedule feasibility is assessed using a discrete event simulation (DES) that incorporates operational uncertainty, variability, and resource availability. The tools provide rapid scenario assessments and responses to variances in the operational environment, and have been used to inform major equipment investments and workforce planning decisions in multiple SNL facilities.« less

Teaching Surgical Hysteroscopy with a Computer

PubMed

Lefebvre; Cote; Lefebvre

1996-08-01

Using a hysteroscope can be simulated on a computer. It will improve physician training by measuring basic knowledge and abilities, allow different interventions and anatomic variations, minimize the trauma of surgical intervention, and reduce operative casualties. An integrated questionnaire covers instrumentation, fluid infusion, power source, indications and preparation for endometrial ablation, surgical techniques, and complications to evaluate the user's knowledge. The operation simulation then proceeds. In the endometrial cavity, by virtual simulation, the operating field should appear in real time to allow physicians to adapt the trajectory of the instruments. The computer is an IBM PC compatible. We use a modified joystick with optical encoders to know the instrument position. The simulation can be repeated as desired. An evaluation system is integrated in the software to keep the user informed on the amount of burn area(s) that have been completed. This prototype model is available.

Modeling track access charge to enhance railway industry performance

NASA Astrophysics Data System (ADS)

Berawi, Mohammed Ali; Miraj, Perdana; Berawi, Abdur Rohim Boy; Susantono, Bambang; Leviakangas, Pekka; Radiansyah, Hendra

2017-11-01

Indonesia attempts to improve nation's competitiveness by increasing the quality and the availability of railway network. However, the infrastructure improperly managed by the operator in terms of the technical issue. One of the reasons for this problem is an unbalanced value of infrastructure charge. In 2000's track access charge and infrastructure maintenance and operation for Indonesia railways are equal and despite current formula of the infrastructure charge, issues of transparency and accountability still in question. This research aims to produce an alternative scheme of track access charge by considering marginal cost plus markup (MC+) approach. The research combines qualitative and quantitative method through an in-depth interview and financial analysis. The result will generate alternative formula of infrastructure charge in Indonesia's railway industry. The simulation also conducted to estimate track access charge for the operator and to forecast government support in terms of subsidy. The result is expected to enhance railway industry performance and competitiveness.

Antiviral Information Management System (AIMS): a prototype for operational innovation in drug development.

PubMed

Jadhav, Pravin R; Neal, Lauren; Florian, Jeff; Chen, Ying; Naeger, Lisa; Robertson, Sarah; Soon, Guoxing; Birnkrant, Debra

2010-09-01

This article presents a prototype for an operational innovation in knowledge management (KM). These operational innovations are geared toward managing knowledge efficiently and accessing all available information by embracing advances in bioinformatics and allied fields. The specific components of the proposed KM system are (1) a database to archive hepatitis C virus (HCV) treatment data in a structured format and retrieve information in a query-capable manner and (2) an automated analysis tool to inform trial design elements for HCV drug development. The proposed framework is intended to benefit drug development by increasing efficiency of dose selection and improving the consistency of advice from US Food and Drug Administration (FDA). It is also hoped that the framework will encourage collaboration among FDA, industry, and academic scientists to guide the HCV drug development process using model-based quantitative analysis techniques.

Development of high-performing semiconducting polymers for organic electrochemical transistors (Conference Presentation)

NASA Astrophysics Data System (ADS)

Nielsen, Christian

2016-11-01

The organic electrochemical transistor (OECT), capable of amplifying small electrical signals in an aqueous environment, is an ideal device to utilize in organic bioelectronic applications involving for example neural interfacing and diagnostics. Currently, most OECTs are fabricated with commercially available conducting poly(3,4-ethylenedioxythiophene)-based suspensions such as PEDOT:PSS and are therefore operated in depletion mode giving rise to devices that are permanently on with non-optimal operational voltage. With the aim to develop and utilize efficient accumulation mode OECT devices, we discuss here our recent results regarding the design, synthesis and performance of novel intrinsic semiconducting polymers. Covering key aspects such as ion and charge transport in the bulk semiconductor and operational voltage and stability of the materials and devices, we have elucidated important structure-property relationships. We illustrate the improvements this approach has afforded in the development of high performance accumulation mode OECT materials.

The economics of nuclear power

NASA Astrophysics Data System (ADS)

Horst, Ronald L.

We extend economic analysis of the nuclear power industry by developing and employing three tools. They are (1) compilation and unification of operating and accounting data sets for plants and sites, (2) an abstract industry model with major economic agents and features, and (3) a model of nuclear power plant operators. We build a matched data set to combine dissimilar but mutually dependant bodies of information. We match detailed information on the activities and conditions of individual plants to slightly more aggregated financial data. Others have exploited the data separately, but we extend the sets and pool available data sets. The data reveal dramatic changes in the industry over the past thirty years. The 1980s proved unprofitable for the industry. This is evident both in the cost data and in the operator activity data. Productivity then improved dramatically while cost growth stabilized to the point of industry profitability. Relative electricity prices may be rising after nearly two decades of decline. Such demand side trends, together with supply side improvements, suggest a healthy industry. Our microeconomic model of nuclear power plant operators employs a forward-looking component to capture the information set available to decision makers and to model the decision-making process. Our model includes features often overlooked elsewhere, including electricity price equations and liability. Failure to account for changes in electricity price trends perhaps misled earlier scholars, and they attributed to other causes the effects on profits of changing price structures. The model includes potential losses resulting from catastrophic nuclear accidents. Applications include historical simulations and forecasts. Nuclear power involves risk, and accident costs are borne both by plant owners and the public. Authorities regulate the industry and balance conflicting desires for economic gain and safety. We construct an extensible model with regulators, plant operators, insurance companies, and consumers. The model possesses key attributes of the industry seldom found in combination elsewhere. We then add additional details to make the model truer to reality. The work extends and corrects existing literature on the definition, effects, and magnitudes of implicit subsidies resulting from liability limits.

76 FR 80261 - National Emission Standards for Hazardous Air Pollutants: Area Source Standards for Prepared...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-23

... specifications and operating instructions, if available, or standard operating procedures must be developed by... manufacturer's specifications and operating instructions, if available, or standard operating procedures must... operating specifications or standard operating procedures developed by the prepared feeds manufacturer be...

How much can a single webcam tell to the operation of a water system?

NASA Astrophysics Data System (ADS)

Giuliani, Matteo; Castelletti, Andrea; Fedorov, Roman; Fraternali, Piero

2017-04-01

Recent advances in environmental monitoring are making a wide range of hydro-meteorological data available with a great potential to enhance understanding, modelling and management of environmental processes. Despite this progress, continuous monitoring of highly spatiotemporal heterogeneous processes is not well established yet, especially in inaccessible sites. In this context, the unprecedented availability of user-generated data on the web might open new opportunities for enhancing real-time monitoring and modeling of environmental systems based on data that are public, low-cost, and spatiotemporally dense. In this work, we focus on snow and contribute a novel crowdsourcing procedure for extracting snow-related information from public web images, either produced by users or generated by touristic webcams. A fully automated process fetches mountain images from multiple sources, identifies the peaks present therein, and estimates virtual snow indexes representing a proxy of the snow-covered area. The operational value of the obtained virtual snow indexes is then assessed for a real-world water-management problem, where we use these indexes for informing the daily control of a regulated lake supplying water for multiple purposes. Numerical results show that such information is effective in extending the anticipation capacity of the lake operations, ultimately improving the system performance. Our procedure has the potential for complementing traditional snow-related information, minimizing costs and efforts for obtaining the virtual snow indexes and, at the same time, maximizing the portability of the procedure to several locations where such public images are available.

Hydrologic scales, cloud variability, remote sensing, and models: Implications for forecasting snowmelt and streamflow

USGS Publications Warehouse

Simpson, James J.; Dettinger, M.D.; Gehrke, F.; McIntire, T.J.; Hufford, Gary L.

2004-01-01

Accurate prediction of available water supply from snowmelt is needed if the myriad of human, environmental, agricultural, and industrial demands for water are to be satisfied, especially given legislatively imposed conditions on its allocation. Robust retrievals of hydrologic basin model variables (e.g., insolation or areal extent of snow cover) provide several advantages over the current operational use of either point measurements or parameterizations to help to meet this requirement. Insolation can be provided at hourly time scales (or better if needed during rapid melt events associated with flooding) and at 1-km spatial resolution. These satellite-based retrievals incorporate the effects of highly variable (both in space and time) and unpredictable cloud cover on estimates of insolation. The insolation estimates are further adjusted for the effects of basin topography using a high-resolution digital elevation model prior to model input. Simulations of two Sierra Nevada rivers in the snowmelt seasons of 1998 and 1999 indicate that even the simplest improvements in modeled insolation can improve snowmelt simulations, with 10%-20% reductions in root-mean-square errors. Direct retrieval of the areal extent of snow cover may mitigate the need to rely entirely on internal calculations of this variable, a reliance that can yield large errors that are difficult to correct until long after the season is complete and that often leads to persistent underestimates or overestimates of the volumes of the water to operational reservoirs. Agencies responsible for accurately predicting available water resources from the melt of snowpack [e.g., both federal (the National Weather Service River Forecast Centers) and state (the California Department of Water Resources)] can benefit by incorporating concepts developed herein into their operational forecasting procedures. ?? 2004 American Meteorological Society.

Forecasting Wind and Solar Generation: Improving System Operations, Greening the Grid (Spanish Version)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Tian; Chernyakhovskiy, Ilya; Brancucci Martinez-Anido, Carlo

This document is the Spanish version of 'Greening the Grid- Forecasting Wind and Solar Generation Improving System Operations'. It discusses improving system operations with forecasting with and solar generation. By integrating variable renewable energy (VRE) forecasts into system operations, power system operators can anticipate up- and down-ramps in VRE generation in order to cost-effectively balance load and generation in intra-day and day-ahead scheduling. This leads to reduced fuel costs, improved system reliability, and maximum use of renewable resources.

Space Shuttle Upgrades: Long Life Alkaline Fuel Cell

NASA Technical Reports Server (NTRS)

McCurdy, Kerri

2004-01-01

NASA has utilized the alkaline fuel cell technology to provide electrical power for manned launch vehicles such as Gemini, Apollo, and the Space Shuttle. The current Shuttle alkaline fuel cells are procured from UTC Fuel Cells, a United Technologies Company. The alkaline fuel cells are very reliable but the operating life is limited to 2600 hours due to voltage degradation of the individual cells. The main limiting factor in the life of the cells is corrosion of the cell's fiberglass/epoxy frame by the aqueous potassium hydroxide electrolyte. To reduce operating costs, the orbiter program office approved the Long Life Alkaline Fuel Cell (LLAFC) program as a shuttle upgrade in 1999 to increase the operating life of the fuel cell powerplant to 5000 hours. The LLAFC program incorporates improving the cell by extending the length of the corrosion path, which reduces the cell frame corrosion. UTCFC performed analysis to understand the fundamental mechanisms that drive the cell frame corrosion. The analysis indicated that the corrosion path started along the bond line between the cathode and the cell frame. Analysis also showed that the oxygen available at the cathode, the catalyst on the electrode, and the electrode substrate all supported or intensified the corrosion. The new cell design essentially doubled the corrosion path to mitigate the problem. A 10-cell stack was tested for 5000 hours during the development phase of this program to verify improved cell performance. A complete 96-cell stack was then tested for 5000 hours during the full manned-space qualification phase of this program. Additional upgrades to the powerplant under this program are: replacing the aluminum body in the pressure regulator with stainless steel to reduce corrosion, improving stack insulator plate with improved resistance to stress failure and improved temperature capability, and replacing separator plate elastomer seals with a more durable material and improved seal retention.

Incorporation of operator knowledge for improved HMDS GPR classification

NASA Astrophysics Data System (ADS)

Kennedy, Levi; McClelland, Jessee R.; Walters, Joshua R.

2012-06-01

The Husky Mine Detection System (HMDS) detects and alerts operators to potential threats observed in groundpenetrating RADAR (GPR) data. In the current system architecture, the classifiers have been trained using available data from multiple training sites. Changes in target types, clutter types, and operational conditions may result in statistical differences between the training data and the testing data for the underlying features used by the classifier, potentially resulting in an increased false alarm rate or a lower probability of detection for the system. In the current mode of operation, the automated detection system alerts the human operator when a target-like object is detected. The operator then uses data visualization software, contextual information, and human intuition to decide whether the alarm presented is an actual target or a false alarm. When the statistics of the training data and the testing data are mismatched, the automated detection system can overwhelm the analyst with an excessive number of false alarms. This is evident in the performance of and the data collected from deployed systems. This work demonstrates that analyst feedback can be successfully used to re-train a classifier to account for variable testing data statistics not originally captured in the initial training data.

Di-tri-octahedral smectite for the prevention of post-operative diarrhea in equids with surgical disease of the large intestine: results of a randomized clinical trial.

PubMed

Hassel, Diana M; Smith, Phoebe A; Nieto, Jorge E; Beldomenico, Pablo; Spier, Sharon J

2009-11-01

The aim of this study was to evaluate the effects of a commercially available di-tri-octahedral (DTO) smectite product on clinical signs and prevalence of post-operative diarrhea in horses with colic associated with disease of the large intestine. Sixty-seven horses with surgical disease of the large intestine were randomly assigned to be treated with DTO smectite (n=37; 0.5 kg via nasogastric intubation every 24 h for 3 days post-operatively) or a placebo (n=30). The effect of treatment on fecal scores and clinical and hematological parameters, including heart rate, mucous membrane color, temperature, total white blood cell count, total neutrophil count and total plasma protein values, were determined. Horses treated with DTO smectite had a significant reduction in the prevalence of post-operative diarrhea (10.8%), compared with controls (41.4%). A significant improvement in mucous membrane color was observed 72 h post-operatively in horses receiving treatment, compared with placebo. Administration of DTO smectite to colic patients with disease of the large intestine reduced the occurrence of diarrhea in the early post-operative period.

Progress in Space Weather Modeling and Observations Needed to Improve the Operational NAIRAS Model Aircraft Radiation Exposure Predictions

NASA Astrophysics Data System (ADS)

Mertens, C. J.; Kress, B. T.; Wiltberger, M. J.; Tobiska, W.; Xu, X.

2011-12-01

The Nowcast of Atmospheric Ionizing Radiation for Aviation Safety (NAIRAS) is a prototype operational model for predicting commercial aircraft radiation exposure from galactic and solar cosmic rays. NAIRAS predictions are currently streaming live from the project's public website, and the exposure rate nowcast is also available on the SpaceWx smartphone app for iPhone, IPad, and Android. Cosmic rays are the primary source of human exposure to high linear energy transfer radiation at aircraft altitudes, which increases the risk of cancer and other adverse health effects. Thus, the NAIRAS model addresses an important national need with broad societal, public health and economic benefits. The processes responsible for the variability in the solar wind, interplanetary magnetic field, solar energetic particle spectrum, and the dynamical response of the magnetosphere to these space environment inputs, strongly influence the composition and energy distribution of the atmospheric ionizing radiation field. During the development of the NAIRAS model, new science questions were identified that must be addressed in order to obtain a more reliable and robust operational model of atmospheric radiation exposure. Addressing these science questions require improvements in both space weather modeling and observations. The focus of this talk is to present these science questions, the proposed methodologies for addressing these science questions, and the anticipated improvements to the operational predictions of atmospheric radiation exposure. The overarching goal of this work is to provide a decision support tool for the aviation industry that will enable an optimal balance to be achieved between minimizing health risks to passengers and aircrew while simultaneously minimizing costs to the airline companies.

Distributed data transmitter

DOEpatents

Brown, Kenneth Dewayne [Grain Valley, MO; Dunson, David [Kansas City, MO

2006-08-08

A distributed data transmitter (DTXR) which is an adaptive data communication microwave transmitter having a distributable architecture of modular components, and which incorporates both digital and microwave technology to provide substantial improvements in physical and operational flexibility. The DTXR has application in, for example, remote data acquisition involving the transmission of telemetry data across a wireless link, wherein the DTXR is integrated into and utilizes available space within a system (e.g., a flight vehicle). In a preferred embodiment, the DTXR broadly comprises a plurality of input interfaces; a data modulator; a power amplifier; and a power converter, all of which are modularly separate and distinct so as to be substantially independently physically distributable and positionable throughout the system wherever sufficient space is available.

Distributed data transmitter

DOEpatents

Brown, Kenneth Dewayne [Grain Valley, MO; Dunson, David [Kansas City, MO

2008-06-03

A distributed data transmitter (DTXR) which is an adaptive data communication microwave transmitter having a distributable architecture of modular components, and which incorporates both digital and microwave technology to provide substantial improvements in physical and operational flexibility. The DTXR has application in, for example, remote data acquisition involving the transmission of telemetry data across a wireless link, wherein the DTXR is integrated into and utilizes available space within a system (e.g., a flight vehicle). In a preferred embodiment, the DTXR broadly comprises a plurality of input interfaces; a data modulator; a power amplifier; and a power converter, all of which are modularly separate and distinct so as to be substantially independently physically distributable and positionable throughout the system wherever sufficient space is available.

Energy management and vehicle synthesis

NASA Astrophysics Data System (ADS)

Czysz, P.; Murthy, S. N. B.

The major drivers in the development of launch vehicles for the twenty-first century are reduction in cost of vehicles and operations, continuous reusability, mission abort capability with vehicle recovery, and readiness. One approach to the design of such vehicles is to emphasize energy management and propulsion as being the principal means of improvements given the available industrial capability and the required freedom in selecting configuration concept geometries. A methodology has been developed for the rational synthesis of vehicles based on the setting up and utilization of available data and projections, and a reference vehicle. The application of the methodology is illustrated for a single stage to orbit (SSTO) with various limits for the use of airbreathing propulsion.

Energy management and vehicle synthesis

NASA Technical Reports Server (NTRS)

Czysz, P.; Murthy, S. N. B.

1995-01-01

The major drivers in the development of launch vehicles for the twenty-first century are reduction in cost of vehicles and operations, continuous reusability, mission abort capability with vehicle recovery, and readiness. One approach to the design of such vehicles is to emphasize energy management and propulsion as being the principal means of improvements given the available industrial capability and the required freedom in selecting configuration concept geometries. A methodology has been developed for the rational synthesis of vehicles based on the setting up and utilization of available data and projections, and a reference vehicle. The application of the methodology is illustrated for a single stage to orbit (SSTO) with various limits for the use of airbreathing propulsion.

Optimizing sterilization logistics in hospitals.

PubMed

van de Klundert, Joris; Muls, Philippe; Schadd, Maarten

2008-03-01

This paper deals with the optimization of the flow of sterile instruments in hospitals which takes place between the sterilization department and the operating theatre. This topic is especially of interest in view of the current attempts of hospitals to cut cost by outsourcing sterilization tasks. Oftentimes, outsourcing implies placing the sterilization unit at a larger distance, hence introducing a longer logistic loop, which may result in lower instrument availability, and higher cost. This paper discusses the optimization problems that have to be solved when redesigning processes so as to improve material availability and reduce cost. We consider changing the logistic management principles, use of visibility information, and optimizing the composition of the nets of sterile materials.

Advanced Electrical Materials and Components Being Developed

NASA Technical Reports Server (NTRS)

Schwarze, Gene E.

2004-01-01

All aerospace systems require power management and distribution (PMAD) between the energy and power source and the loads. The PMAD subsystem can be broadly described as the conditioning and control of unregulated power from the energy source and its transmission to a power bus for distribution to the intended loads. All power and control circuits for PMAD require electrical components for switching, energy storage, voltage-to-current transformation, filtering, regulation, protection, and isolation. Advanced electrical materials and component development technology is a key technology to increasing the power density, efficiency, reliability, and operating temperature of the PMAD. The primary means to develop advanced electrical components is to develop new and/or significantly improved electronic materials for capacitors, magnetic components, and semiconductor switches and diodes. The next important step is to develop the processing techniques to fabricate electrical and electronic components that exceed the specifications of presently available state-of-the-art components. The NASA Glenn Research Center's advanced electrical materials and component development technology task is focused on the following three areas: 1) New and/or improved dielectric materials for the development of power capacitors with increased capacitance volumetric efficiency, energy density, and operating temperature; 2) New and/or improved high-frequency, high-temperature soft magnetic materials for the development of transformers and inductors with increased power density, energy density, electrical efficiency, and operating temperature; 3) Packaged high-temperature, high-power density, high-voltage, and low-loss SiC diodes and switches.

Preliminary Trade Study of Phase Change Heat Sinks

NASA Technical Reports Server (NTRS)

Anderson, Molly; Leimkeuhler, Thomas; Quinn, Gregory; Golliher, Eric

2006-01-01

For short durations, phase change based heat rejection systems are a very effective way of removing heat from spacecraft. Future NASA vehicles, such as the Crew Exploration Vehicle (CEV), will require non-radiative heat rejection systems during at least a portion of the planned mission, just as their predecessors have. While existing technologies are available to modify, such as Apollo era sublimators, or the Space Shuttle Flash Evaporator System (FES), several new technologies are under development or investigation to progress beyond these existing heat rejection systems. Examples include the Multi-Fluid Evaporator developed by Hamilton Sundstrand, improvements upon the Contaminant Insensitive Sublimator originally developed for the X-38 program, and a Compact Flash Evaporator System (CFES). Other possibilities evaluate new ways of operating existing designs. The new developments are targeted at increasing operating life, expanding the environments in which the system can operate, improving the mass and volume characteristics, or some combination of these or other improvements. This paper captures the process and results of a preliminary trade study performed at Johnson Space Center to compare the various existing and proposed phase change based heat rejection systems for the CEV. Because the new systems are still in development, and the information on existing systems is extrapolation, this trade study is not meant to suggest a final decision for future vehicles. The results of this early trade study are targeted to aid the development efforts for the new technologies by identifying issues that could reduce the chances of selection for the CEV.

Role of extent of resection on quality of life in patients with newly diagnosed GBM.

PubMed

Choudry, Usama Khalid; Shaikh, Huzaifa Ismail; Nisar, Areeba; Khan, Saad Akhtar; Shamim, Muhammad Shahzad

2018-01-01

Glioblastomas known for their adverse outcomes are most reportedly managed by surgical resection. Studies on the impact of (Extent of Resection) EOR against Quality of Life (QOL) are very limited. We have collected data from recent studies in this review to extract a general consensus among the neurosurgeons regarding the EOR. Key parameters like functional independence, neurocognitive improvements and global health status have been explored in the context of QOL. The currently available data suggests that an increased EOR may help improve QOL in GBM patients. With the help of recent advancements it may be possible to attain a better extent of resection while operating on GBMs.

Improving the detection efficiency in nuclear emulsion trackers

NASA Astrophysics Data System (ADS)

Alexandrov, A.; Bozza, C.; Buonaura, A.; Consiglio, L.; D`Ambrosio, N.; Lellis, G. De; De Serio, M.; Di Capua, F.; Di Crescenzo, A.; Di Ferdinando, D.; Di Marco, N.; Fini, R. A.; Galati, G.; Giacomelli, G.; Grella, G.; Hosseini, B.; Kose, U.; Lauria, A.; Longhin, A.; Mandrioli, G.; Mauri, N.; Medinaceli, E.; Montesi, M. C.; Paoloni, A.; Pastore, A.; Patrizii, L.; Pozzato, M.; Pupilli, F.; Rescigno, R.; Roda, M.; Rosa, G.; Schembri, A.; Shchedrina, T.; Simone, S.; Sioli, M.; Sirignano, C.; Sirri, G.; Spinetti, M.; Stellacci, S. M.; Tenti, M.; Tioukov, V.

2015-03-01

Nuclear emulsion films are a tracking device with unique space resolution. Their use in nowadays large-scale experiments relies on the availability of automated microscope operating at very high speed. In this paper we describe the features and the latest improvements of the European Scanning System, a last-generation automated microscope for emulsion scanning. In particular, we present a new method for the recovery of tracking inefficiencies. Stacks of double coated emulsion films have been exposed to a 10 GeV/c pion beam. Efficiencies as high as 98% have been achieved for minimum ionising particle tracks perpendicular to the emulsion films and of 93% for tracks with tan(θ) ≃ 0.8.

Thermal-Performance Instability in Piezoresistive Sensors: Inducement and Improvement

PubMed Central

Liu, Yan; Wang, Hai; Zhao, Wei; Qin, Hongbo; Fang, Xuan

2016-01-01

The field of piezoresistive sensors has been undergoing a significant revolution in terms of design methodology, material technology and micromachining process. However, the temperature dependence of sensor characteristics remains a hurdle to cross. This review focuses on the issues in thermal-performance instability of piezoresistive sensors. Based on the operation fundamental, inducements to the instability are investigated in detail and correspondingly available ameliorative methods are presented. Pros and cons of each improvement approach are also summarized. Though several schemes have been proposed and put into reality with favorable achievements, the schemes featuring simple implementation and excellent compatibility with existing techniques are still emergently demanded to construct a piezoresistive sensor with excellent comprehensive performance. PMID:27886125

Automated mixed traffic vehicle design AMTV 2

NASA Technical Reports Server (NTRS)

Johnston, A. R.; Marks, R. A.; Cassell, P. L.

1982-01-01

The design of an improved and enclosed Automated Mixed Traffic Transit (AMTT) vehicle is described. AMTT is an innovative concept for low-speed tram-type transit in which suitable vehicles are equipped with sensors and controls to permit them to operate in an automated mode on existing road or walkway surfaces. The vehicle chassis and body design are presented in terms of sketches and photographs. The functional design of the sensing and control system is presented, and modifications which could be made to the baseline design for improved performance, in particular to incorporate a 20-mph capability, are also discussed. The vehicle system is described at the block-diagram-level of detail. Specifications and parameter values are given where available.

Pediatric liver transplantation

PubMed Central

Spada, Marco; Riva, Silvia; Maggiore, Giuseppe; Cintorino, Davide; Gridelli, Bruno

2009-01-01

In previous decades, pediatric liver transplantation has become a state-of-the-art operation with excellent success and limited mortality. Graft and patient survival have continued to improve as a result of improvements in medical, surgical and anesthetic management, organ availability, immunosuppression, and identification and treatment of postoperative complications. The utilization of split-liver grafts and living-related donors has provided more organs for pediatric patients. Newer immunosuppression regimens, including induction therapy, have had a significant impact on graft and patient survival. Future developments of pediatric liver transplantation will deal with long-term follow-up, with prevention of immunosuppression-related complications and promotion of as normal growth as possible. This review describes the state-of-the-art in pediatric liver transplantation. PMID:19222089

An approach to the drone fleet survivability assessment based on a stochastic continues-time model

NASA Astrophysics Data System (ADS)

Kharchenko, Vyacheslav; Fesenko, Herman; Doukas, Nikos

2017-09-01

An approach and the algorithm to the drone fleet survivability assessment based on a stochastic continues-time model are proposed. The input data are the number of the drones, the drone fleet redundancy coefficient, the drone stability and restoration rate, the limit deviation from the norms of the drone fleet recovery, the drone fleet operational availability coefficient, the probability of the drone failure-free operation, time needed for performing the required tasks by the drone fleet. The ways for improving the recoverable drone fleet survivability taking into account amazing factors of system accident are suggested. Dependencies of the drone fleet survivability rate both on the drone stability and the number of the drones are analysed.

Operation of Negative Ion Sources at the Cooler Synchrotron COSY/Juelich

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gebel, R.; Felden, O.; Maier, R.

2011-09-26

The Institute for Nuclear Physics at the Forschungszentrum Juelich is dedicated to fundamental research in the field of hadron, particle and nuclear physics. Main activities are the development of the High Energy Storage Ring for the Facility for Antiproton and Ion Research at Darmstadt and the operation and improvement of the cooler synchrotron COSY at Juelich. The injector, a cyclotron with polarized and unpolarized H{sup -} and D{sup -} sources, has exceeded 7000 hours availability per year, averaged over the last decade. Work in progress is the investigation of production, extraction and transport of the low energy 4.5 keV/u ionmore » beams. A brief overview of the activities is presented.« less

[Enhanced Recovery after Surgery from Theory to Practice
What do We Need to Do?

PubMed

Che, Guowei; Liu, Lunxu; Zhou, Qinghua

2017-04-20

Enhanced recovery after surgery (ERAS) is a paradigm shift in perioperative care, resulting in substantial improvements in clinical outcomes, shorter length of hospital stay and cost savings. But the current ERAS either by application of breadth or depth is not enough, why? The main reason is the lack of "operability, evaluation, repetition" ERAS protocol and suitable for clinical extensive application protocol. How to form the clinical available protocol? Operational mainly refers to the clinical scheme is simple and feasible, and protocol compliance is good; Evaluate refers to the methods used before, during and after are the objective evaluation criteria and plan; Repeatable is clinical scheme repeatability in the process of single or multiple center.

Reliability of the quench protection system for the LHC superconducting elements

NASA Astrophysics Data System (ADS)

Vergara Fernández, A.; Rodríguez-Mateos, F.

2004-06-01

The Quench Protection System (QPS) is the sole system in the Large Hadron Collider machine monitoring the signals from the superconducting elements (bus bars, current leads, magnets) which form the cold part of the electrical circuits. The basic functions to be accomplished by the QPS during the machine operation will be briefly presented. With more than 4000 internal trigger channels (quench detectors and others), the final QPS design is the result of an optimised balance between on-demand availability and false quench reliability. The built-in redundancy for the different equipment will be presented, focusing on the calculated, expected number of missed quenches and false quenches. Maintenance strategies in order to improve the performance over the years of operation will be addressed.

The Design and Implementation of Network Teaching Platform Basing on .NET

NASA Astrophysics Data System (ADS)

Yanna, Ren

This paper addresses the problem that students under traditional teaching model have poor operation ability and studies in depth the network teaching platform in domestic colleges and universities, proposing the design concept of network teaching platform of NET + C # + SQL excellent course and designing the overall structure, function module and back-end database of the platform. This paper emphatically expounds the use of MD5 encryption techniques in order to solve data security problems and the assessment of student learning using ADO.NET database access technology as well as the mathematical formula. The example shows that the network teaching platform developed by using WEB application technology has higher safety and availability, and thus improves the students' operation ability.

How to Get Data from NOAA Environmental Satellites: An Overview of Operations, Products, Access and Archive

NASA Astrophysics Data System (ADS)

Donoho, N.; Graumann, A.; McNamara, D. P.

2015-12-01

In this presentation we will highlight access and availability of NOAA satellite data for near real time (NRT) and retrospective product users. The presentation includes an overview of the current fleet of NOAA satellites and methods of data distribution and access to hundreds of imagery and products offered by the Environmental Satellite Processing Center (ESPC) and the Comprehensive Large Array-data Stewardship System (CLASS). In particular, emphasis on the various levels of services for current and past observations will be presented. The National Environmental Satellite, Data, and Information Service (NESDIS) is dedicated to providing timely access to global environmental data from satellites and other sources. In special cases, users are authorized direct access to NESDIS data distribution systems for environmental satellite data and products. Other means of access include publicly available distribution services such as the Global Telecommunication System (GTS), NOAA satellite direct broadcast services and various NOAA websites and ftp servers, including CLASS. CLASS is NOAA's information technology system designed to support long-term, secure preservation and standards-based access to environmental data collections and information. The National Centers for Environmental Information (NCEI) is responsible for the ingest, quality control, stewardship, archival and access to data and science information. This work will also show the latest technology improvements, enterprise approach and future plans for distribution of exponentially increasing data volumes from future NOAA missions. A primer on access to NOAA operational satellite products and services is available at http://www.ospo.noaa.gov/Organization/About/access.html. Access to post-operational satellite data and assorted products is available at http://www.class.noaa.gov

What is the safety of nonemergent operative procedures performed at night? A study of 10,426 operations at an academic tertiary care hospital using the American College of Surgeons national surgical quality program improvement database.

PubMed

Turrentine, Florence E; Wang, Hongkun; Young, Jeffrey S; Calland, James Forrest

2010-08-01

Ever-increasing numbers of in-house acute care surgeons and competition for operating room time during normal daytime business hours have led to an increased frequency of nonemergent general and vascular surgery procedures occurring at night when there are fewer residents, consultants, nurses, and support staff available for assistance. This investigation tests the hypothesis that patients undergoing such procedures after hours are at increased risk for postoperative morbidity and mortality. Clinical data for 10,426 operative procedures performed over a 5-year period at a single academic tertiary care hospital were obtained from the American College of Surgeons National Surgical Quality Improvement Program Database. The prevalence of preoperative comorbid conditions, postoperative length of stay, morbidity, and mortality was compared between two cohorts of patients: one who underwent nonemergent operative procedures at night and other who underwent similar procedures during the day. Subsequent statistical comparisons utilized chi tests for comparisons of categorical variables and F-tests for continuous variables. Patients undergoing procedures at night had a greater prevalence of serious preoperative comorbid conditions. Procedure complexity as measured by relative value unit did not differ between groups, but length of stay was longer after night procedures (7.8 days vs. 4.3 days, p < 0.0001). Patients undergoing nonemergent general and vascular surgery procedures at night in an academic medical center do not seem to be at increased risk for postoperative morbidity or mortality. Performing nonemergent procedures at night seems to be a safe solution for daytime overcrowding of operating rooms.

Improving the Transition of Earth Satellite Observations from Research to Operations

NASA Technical Reports Server (NTRS)

Goodman, Steven J.; Lapenta, William M.; Jedlovec, Gary J.

2004-01-01

There are significant gaps between the observations, models, and decision support tools that make use of new data. These challenges include: 1) Decreasing the time to incorporate new satellite data into operational forecast assimilation systems, 2) Blending in-situ and satellite observing systems to produce the most accurate and comprehensive data products and assessments, 3) Accelerating the transition from research to applications through national test beds, field campaigns, and pilot demonstrations, and 4) Developing the partnerships and organizational structures to effectively transition new technology into operations. At the Short-term Prediction Research and Transition (SPORT) Center in Huntsville, Alabama, a NASA-NOAA-University collaboration has been developed to accelerate the infusion of NASA Earth science observations, data assimilation and modeling research into NWS forecast operations and decision-making. The SPoRT Center research focus is to improve forecasts through new observation capability and the regional prediction objectives of the US Weather Research Program dealing with 0-1 day forecast issues such as convective initiation and 24-hr quantitative precipitation forecasting. The near real-time availability of high-resolution experimental products of the atmosphere, land, and ocean from the Moderate Resolution Imaging Spectroradiometer (MODIS), the Advanced Infrared Spectroradiometer (AIRS), and lightning mapping systems provide an opportunity for science and algorithm risk reduction, and for application assessment prior to planned observations from the next generation of operational low Earth orbiting and geostationary Earth orbiting satellites. This paper describes the process for the transition of experimental products into forecast operations, current products undergoing assessment by forecasters, and plans for the future. The SPoRT Web page is at (http://www.ghcc.msfc.nasa.gov/sport).

Towards online iris and periocular recognition under relaxed imaging constraints.

PubMed

Tan, Chun-Wei; Kumar, Ajay

2013-10-01

Online iris recognition using distantly acquired images in a less imaging constrained environment requires the development of a efficient iris segmentation approach and recognition strategy that can exploit multiple features available for the potential identification. This paper presents an effective solution toward addressing such a problem. The developed iris segmentation approach exploits a random walker algorithm to efficiently estimate coarsely segmented iris images. These coarsely segmented iris images are postprocessed using a sequence of operations that can effectively improve the segmentation accuracy. The robustness of the proposed iris segmentation approach is ascertained by providing comparison with other state-of-the-art algorithms using publicly available UBIRIS.v2, FRGC, and CASIA.v4-distance databases. Our experimental results achieve improvement of 9.5%, 4.3%, and 25.7% in the average segmentation accuracy, respectively, for the UBIRIS.v2, FRGC, and CASIA.v4-distance databases, as compared with most competing approaches. We also exploit the simultaneously extracted periocular features to achieve significant performance improvement. The joint segmentation and combination strategy suggest promising results and achieve average improvement of 132.3%, 7.45%, and 17.5% in the recognition performance, respectively, from the UBIRIS.v2, FRGC, and CASIA.v4-distance databases, as compared with the related competing approaches.

Latest developments in peri-operative monitoring of the high-risk major surgery patient.

PubMed

Green, David; Paklet, Lise

2010-01-01

Peri-operative monitoring technology has made great strides in the last 20 years with the introduction of minimally invasive devices to measure inter alia stroke volume, cardiac output, depth of anaesthesia and cerebral and tissue oxygen monitoring. Despite these technological advances, peri-operative management of the high risk major surgery patient has remained virtually unchanged. The vast majority of patients undergo a pre-operative assessment which is neither designed to quantify functional capacity nor predict outcome. Anaesthetists then usually monitor these patients using the same technology (e.g. pulse oximetry (SpO2), invasive systemic BP and CVP, end tidal carbon dioxide (etCO2) and anaesthetic agent monitoring) that was available in the early 1980s. Conventional intra-operative management can result in occult low levels of blood flow and oxygen delivery that lead to complications that only occur days or weeks following surgery and give false re-assurance to the anaesthetist that he or she is doing a "good job". Post-operative management then often takes place in an environment with reduced levels of both monitoring equipment and staff expertise. It is perhaps not surprising that outcome still remains poor in high-risk patients.(1) In this review, we will briefly describe the role of peri-operative optimization, some of the available monitors and indicate how their combined use might be beneficial in managing the high-risk surgical patient. We believe that although there is now evidence to suggest that the use of individual new monitors (such as assessment of fluid status, depth of anaesthesia, tissue oxygenation and blood flow) can influence outcome, it will only be their combination that will radically improve the peri-operative management and outcome of high-risk surgical patients. It is a matter of some urgency that large scale, prospective and collaborative studies be designed, funded and executed to prove or disprove this hypothesis. Copyright 2009 Surgical Associates Ltd. Published by Elsevier Ltd. All rights reserved.

Physician Engagement in Improving Operative Supply Chain Efficiency Through Review of Surgeon Preference Cards.

PubMed

Harvey, Lara F B; Smith, Katherine A; Curlin, Howard

To reduce operative costs involved in the purchase, packing, and transport of unnecessary supplies by improving the accuracy of surgeon preference cards. Quality improvement study (Canadian Task Force classification II-3). Gynecologic surgery suite of an academic medical center. Twenty-one specialized and generalist gynecologic surgeons. The preference cards of up to the 5 most frequently performed procedures per surgeon were selected. A total of 81 cards were distributed to 21 surgeons for review. Changes to the cards were communicated to the operating room charge nurse and finalized. Fourteen surgeons returned a total of 48 reviewed cards, 39 of which had changes. A total of 109 disposable supplies were removed from these cards, at a total cost savings of $767.67. The cost per card was reduced by $16 on average for disposables alone. Three reusable instrument trays were also eliminated from the cards, resulting in savings of approximately $925 in processing costs over a 3-month period. Twenty-two items were requested by surgeons to be available on request but were not routinely placed in the room at the start of each case, at a total cost of $6,293.54. The rate of return of unused instruments to storage decreased after our intervention, from 10.1 to 9.6 instruments per case. Surgeon preference cards serve as the basis for economic decision making regarding the purchase, storing, packing, and transport of operative instruments and supplies. A one-time surgeon review of cards resulted in a decrease in the number of disposable and reusable instruments that must be stocked, transported, counted in the operating room, or returned, potentially translating into cost savings. Surgeon involvement in preference card management may reduce waste and provide ongoing cost savings. Copyright © 2017 American Association of Gynecologic Laparoscopists. Published by Elsevier Inc. All rights reserved.

Nirschl surgical technique for concomitant lateral and medial elbow tendinosis: a retrospective review of 53 elbows with a mean follow-up of 11.7 years.

PubMed

Schipper, Oliver N; Dunn, Jonathan H; Ochiai, Derek H; Donovan, J Skye; Nirschl, Robert P

2011-05-01

Combined lateral elbow tendinosis (tennis elbow) and medial elbow tendinosis (golfer's elbow) can be a disabling condition that, if unresponsive to nonoperative treatments, may be effectively treated surgically. The authors are not aware of any study that reports the outcome of a combined operation for lateral and medial elbow tendinosis (country club elbow) performed in the same operative setting. Combined surgical treatment of country club elbow in the same operative setting has similar outcomes to those seen in the literature for single operative procedures. Case series; Level of evidence 4. Outcome measurements included the Numeric Pain Intensity Scale, the Nirschl tennis elbow scoring system, and the American Shoulder and Elbow Surgeons elbow form. Forty-eight patients (53 clinical elbows) were available by telephone, with a minimum time to follow-up of 5 years (range, 5-19 years; mean, 11.7 years). The average Nirschl tennis elbow score improved from 16.7 preoperatively to 70.8 postoperatively (P < .01). The average American Shoulder and Elbow Surgeons elbow score improved from 45.2 to 90.4 (P < .01). The Numeric Pain Intensity Scale score improved from 8.8 to 1.7 (P < .01). By the criteria of the Nirschl tennis elbow score, results were rated excellent in 38 elbows, good in 7 elbows, fair in 5 elbows, and poor in 3 elbows, with 85% (45 of 53) good to excellent results. Patient satisfaction with the surgery averaged 8.7 out of 10. Of the 46 patients who played sports, 44 (96%) reported returning to their sports. When nonoperative treatment of lateral and medial elbow tendinosis fails, combined surgical intervention via the Nirschl operative techniques for country club elbow is highly effective, with results similar to those of single-sided intervention.

Spitzer observatory operations: increasing efficiency in mission operations

NASA Astrophysics Data System (ADS)

Scott, Charles P.; Kahr, Bolinda E.; Sarrel, Marc A.

2006-06-01

This paper explores the how's and why's of the Spitzer Mission Operations System's (MOS) success, efficiency, and affordability in comparison to other observatory-class missions. MOS exploits today's flight, ground, and operations capabilities, embraces automation, and balances both risk and cost. With operational efficiency as the primary goal, MOS maintains a strong control process by translating lessons learned into efficiency improvements, thereby enabling the MOS processes, teams, and procedures to rapidly evolve from concept (through thorough validation) into in-flight implementation. Operational teaming, planning, and execution are designed to enable re-use. Mission changes, unforeseen events, and continuous improvement have often times forced us to learn to fly anew. Collaborative spacecraft operations and remote science and instrument teams have become well integrated, and worked together to improve and optimize each human, machine, and software-system element. Adaptation to tighter spacecraft margins has facilitated continuous operational improvements via automated and autonomous software coupled with improved human analysis. Based upon what we now know and what we need to improve, adapt, or fix, the projected mission lifetime continues to grow - as does the opportunity for numerous scientific discoveries.

Evidence-Based and Value-Based Decision Making About Healthcare Design: An Economic Evaluation of the Safety and Quality Outcomes.

PubMed

Zadeh, Rana; Sadatsafavi, Hessam; Xue, Ryan

2015-01-01

This study describes a vision and framework that can facilitate the implementation of evidence-based design (EBD), scientific knowledge base into the process of the design, construction, and operation of healthcare facilities and clarify the related safety and quality outcomes for the stakeholders. The proposed framework pairs EBD with value-driven decision making and aims to improve communication among stakeholders by providing a common analytical language. Recent EBD research indicates that the design and operation of healthcare facilities contribute to an organization's operational success by improving safety, quality, and efficiency. However, because little information is available about the financial returns of evidence-based investments, such investments are readily eliminated during the capital-investment decision-making process. To model the proposed framework, we used engineering economy tools to evaluate the return on investments in six successful cases, identified by a literature review, in which facility design and operation interventions resulted in reductions in hospital-acquired infections, patient falls, staff injuries, and patient anxiety. In the evidence-based cases, calculated net present values, internal rates of return, and payback periods indicated that the long-term benefits of interventions substantially outweighed the intervention costs. This article explained a framework to develop a research-based and value-based communication language on specific interventions along the planning, design and construction, operation, and evaluation stages. Evidence-based and value-based design frameworks can be applied to communicate the life-cycle costs and savings of EBD interventions to stakeholders, thereby contributing to more informed decision makings and the optimization of healthcare infrastructures. © The Author(s) 2015.

Will available bit rate (ABR) services give us the capability to offer virtual LANs over wide-area ATM networks?

NASA Astrophysics Data System (ADS)

Ferrandiz, Ana; Scallan, Gavin

1995-10-01

The available bit rate (ABR) service allows connections to exceed their negotiated data rates during the life of the connections when excess capacity is available in the network. These connections are subject to flow control from the network in the event of network congestion. The ability to dynamically adjust the data rate of the connection can provide improved utilization of the network and be a valuable service to end users. ABR type service is therefore appropriate for the transmission of bursty LAN traffic over a wide area network in a manner that is more efficient and cost effective than allocating bandwdith at the peak cell rate. This paper describes the ABR service and discusses if it is realistic to operate a LAN like service over a wide area using ABR.

MO/DSD online information server and global information repository access

NASA Technical Reports Server (NTRS)

Nguyen, Diem; Ghaffarian, Kam; Hogie, Keith; Mackey, William

1994-01-01

Often in the past, standards and new technology information have been available only in hardcopy form, with reproduction and mailing costs proving rather significant. In light of NASA's current budget constraints and in the interest of efficient communications, the Mission Operations and Data Systems Directorate (MO&DSD) New Technology and Data Standards Office recognizes the need for an online information server (OLIS). This server would allow: (1) dissemination of standards and new technology information throughout the Directorate more quickly and economically; (2) online browsing and retrieval of documents that have been published for and by MO&DSD; and (3) searching for current and past study activities on related topics within NASA before issuing a task. This paper explores a variety of available information servers and searching tools, their current capabilities and limitations, and the application of these tools to MO&DSD. Most importantly, the discussion focuses on the way this concept could be easily applied toward improving dissemination of standards and new technologies and improving documentation processes.

Aeronautical technology 2000: A projection of advanced vehicle concepts

NASA Technical Reports Server (NTRS)

1985-01-01

The Aeronautics and Space Engineering Board (ASEB) of the National Research Council conducted a Workshop on Aeronautical Technology: a Projection to the Year 2000 (Aerotech 2000 Workshop). The panels were asked to project advances in aeronautical technologies that could be available by the year 2000. As the workshop was drawing to a close, it became evident that a more comprehensive investigation of advanced air vehicle concepts than was possible in the limited time available at the workshop would be valuable. Thus, a special panel on vehicle applications was organized. In the course of two meetings, the panel identified and described representative types of aircraft judged possible with the workshop's technology projections. These representative aircraft types include: military aircraft; transport aircraft; rotorcraft; extremely high altitude aircraft; and transatmospheric aircraft. Improvements in performance, efficiency, and operational characteristics possible through the application of the workshop's year 2000 technology projections were discussed. The subgroups also identified the technologies considered essential and enhancing or supporting to achieve the projected aircraft improvements.

Millisecond precision psychological research in a world of commodity computers: new hardware, new problems?

PubMed

Plant, Richard R; Turner, Garry

2009-08-01

Since the publication of Plant, Hammond, and Turner (2004), which highlighted a pressing need for researchers to pay more attention to sources of error in computer-based experiments, the landscape has undoubtedly changed, but not necessarily for the better. Readily available hardware has improved in terms of raw speed; multi core processors abound; graphics cards now have hundreds of megabytes of RAM; main memory is measured in gigabytes; drive space is measured in terabytes; ever larger thin film transistor displays capable of single-digit response times, together with newer Digital Light Processing multimedia projectors, enable much greater graphic complexity; and new 64-bit operating systems, such as Microsoft Vista, are now commonplace. However, have millisecond-accurate presentation and response timing improved, and will they ever be available in commodity computers and peripherals? In the present article, we used a Black Box ToolKit to measure the variability in timing characteristics of hardware used commonly in psychological research.

Considerations for developing technologies for an integrated person-borne IED countermeasure architecture

NASA Astrophysics Data System (ADS)

Lombardo, Nicholas J.; Knudson, Christa K.; Rutz, Frederick C.; Pattison, Kerrie J.; Stratton, Rex C.; Wiborg, James C.

2010-04-01

Developing an integrated person-borne improvised explosive device (IED) countermeasure to protect unstructured crowds at large public venues is the goal of the Standoff Technology Integration and Demonstration Program (STIDP), sponsored in part by the U.S. Department of Homeland Security (DHS). The architecture being developed includes countermeasure technologies deployed as a layered defense and enabling technologies for operating the countermeasures as an integrated system. In the architecture, early recognition of potentially higher-risk individuals is crucial. Sensors must be able to detect, with high accuracy, explosives' threat signatures in varying environmental conditions, from a variety of approaches and with dense crowds and limited dwell time. Command-and-control technologies are needed to automate sensor operation, reduce staffing requirements, improve situational awareness, and automate/facilitate operator decisions. STIDP is developing technical and operational requirements for standoff and remotely operated sensors and is working with federal agencies and foreign governments to implement these requirements into their research and development programs. STIDP also is developing requirements for a software platform to rapidly integrate and control various sensors; acquire, analyze, and record their data; and present the data in an operationally relevant manner. Requirements also are being developed for spatial analysis, tracking and assessing threats with available screening resources, and data fusion for operator decision-making.

Biomass burning source characterization requirements in air quality models with and without data assimilation: challenges and opportunities

NASA Astrophysics Data System (ADS)

Hyer, E. J.; Zhang, J. L.; Reid, J. S.; Curtis, C. A.; Westphal, D. L.

2007-12-01

Quantitative models of the transport and evolution of atmospheric pollution have graduated from the laboratory to become a part of the operational activity of forecast centers. Scientists studying the composition and variability of the atmosphere put great efforts into developing methods for accurately specifying sources of pollution, including natural and anthropogenic biomass burning. These methods must be adapted for use in operational contexts, which impose additional strictures on input data and methods. First, only input data sources available in near real-time are suitable for use in operational applications. Second, operational applications must make use of redundant data sources whenever possible. This is a shift in philosophy: in a research context, the most accurate and complete data set will be used, whereas in an operational context, the system must be designed with maximum redundancy. The goal in an operational context is to produce, to the extent possible, consistent and timely output, given sometimes inconsistent inputs. The Naval Aerosol Analysis and Prediction System (NAAPS), a global operational aerosol analysis and forecast system, recently began incorporating assimilation of satellite-derived aerosol optical depth. Assimilation of satellite AOD retrievals has dramatically improved aerosol analyses and forecasts from this system. The use of aerosol data assimilation also changes the strategy for improving the smoke source function. The absolute magnitude of emissions events can be refined through feedback from the data assimilation system, both in real- time operations and in post-processing analysis of data assimilation results. In terms of the aerosol source functions, the largest gains in model performance are now to be gained by reducing data latency and minimizing missed detections. In this presentation, recent model development work on the Fire Locating and Monitoring of Burning Emissions (FLAMBE) system that provides smoke aerosol boundary conditions for NAAPS is described, including redundant integration of multiple satellite platforms and development of feedback loops between the data assimilation system and smoke source.

Architecture and evolution of Goddard Space Flight Center Distributed Active Archive Center

NASA Technical Reports Server (NTRS)

Bedet, Jean-Jacques; Bodden, Lee; Rosen, Wayne; Sherman, Mark; Pease, Phil

1994-01-01

The Goddard Space Flight Center (GSFC) Distributed Active Archive Center (DAAC) has been developed to enhance Earth Science research by improved access to remote sensor earth science data. Building and operating an archive, even one of a moderate size (a few Terabytes), is a challenging task. One of the critical components of this system is Unitree, the Hierarchical File Storage Management System. Unitree, selected two years ago as the best available solution, requires constant system administrative support. It is not always suitable as an archive and distribution data center, and has moderate performance. The Data Archive and Distribution System (DADS) software developed to monitor, manage, and automate the ingestion, archive, and distribution functions turned out to be more challenging than anticipated. Having the software and tools is not sufficient to succeed. Human interaction within the system must be fully understood to improve efficiency to improve efficiency and ensure that the right tools are developed. One of the lessons learned is that the operability, reliability, and performance aspects should be thoroughly addressed in the initial design. However, the GSFC DAAC has demonstrated that it is capable of distributing over 40 GB per day. A backup system to archive a second copy of all data ingested is under development. This backup system will be used not only for disaster recovery but will also replace the main archive when it is unavailable during maintenance or hardware replacement. The GSFC DAAC has put a strong emphasis on quality at all level of its organization. A Quality team has also been formed to identify quality issues and to propose improvements. The DAAC has conducted numerous tests to benchmark the performance of the system. These tests proved to be extremely useful in identifying bottlenecks and deficiencies in operational procedures.

D Cultural Heritage Documentation: a Comparison Between Different Photogrammetric Software and Their Products

NASA Astrophysics Data System (ADS)

Gagliolo, S.; Ausonio, E.; Federici, B.; Ferrando, I.; Passoni, D.; Sguerso, D.

2018-05-01

The conservation of Cultural Heritage depends on the availability of means and resources and, consequently, on the possibility to make effective operations of data acquisition. In facts, on the one hand the creation of data repositories allows the description of the present state-of-art, in order to preserve the testimonial value and to permit the fruition. On the other hand, data acquisition grants a metrical knowledge, which is particularly useful for a direct restoration of the surveyed objects, through the analysis of their 3D digital models. In the last decades, the continuous increase and improvement of 3D survey techniques and of tools for the geometric and digital data management have represented a great support to the development of documentary activities. In particular, Photogrammetry is a survey technique highly appropriate in the creation of data repositories in the field of Cultural Heritage, thanks to its advantages of cheapness, flexibility, speed, and the opportunity to ensure the operators' safety in hazardous areas too. In order to obtain a complete documentation, the high precision of the on-site operations must be coupled with an effective post-processing phase. Hence, a comparison among some of the photogrammetric software currently available was performed by the authors, with a particular attention to the workflow completeness and the final products quality.

MineScan: non-image data monitoring and mining from imaging modalities

NASA Astrophysics Data System (ADS)

Zaidi, Shayan M.; Huff, Dov; Bhalodia, Pankit; Mongkolwat, Pattanasak; Channin, David S.

2003-05-01

This project is intended to capture and interactively display non-image information routinely generated by imaging modalities. This information relates to the device's performance of the individual procedures and is not necessarily available in other information streams such as DICOM headers. While originally intended for use in servicing the modalities, this information can also be presented to radiologists and administrators within the department for both micro- and macro-management purposes. This data can help hospital administrators and radiologists manage available resources and discover clues to indicate what modifications in hospital operations might significantly improve its ability to provide efficient patient care. Data is collected from a departmental CT scanner. The data consists of a running record of exams followed by a list of processing records logged over a 24-hour period. MineScan extracts information from these records and stores it into a database. A statistical program is run once a day to collect relevant metrics. MineScan can be accessed via a Web browser or through an advanced prototype PACS workstation. This information, if provided in real-time, can be used to manage operations in a busy department. Even when provided historically, the data can be used to assess current activity, analyze trends and plan future operations.

Improved NSGA model for multi objective operation scheduling and its evaluation

NASA Astrophysics Data System (ADS)

Li, Weining; Wang, Fuyu

2017-09-01

Reasonable operation can increase the income of the hospital and improve the patient’s satisfactory level. In this paper, by using multi object operation scheduling method with improved NSGA algorithm, it shortens the operation time, reduces the operation costand lowers the operation risk, the multi-objective optimization model is established for flexible operation scheduling, through the MATLAB simulation method, the Pareto solution is obtained, the standardization of data processing. The optimal scheduling scheme is selected by using entropy weight -Topsis combination method. The results show that the algorithm is feasible to solve the multi-objective operation scheduling problem, and provide a reference for hospital operation scheduling.

Radio frequency heating for in-situ remediation of DNAPL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kasevich, R.S.

1996-08-01

In-situ radio frequency (RF) heating technology for treating soils contaminated with dense nonaqueous phase liquids (DNAPLs) is described. RF imparts heat to non-conducting materials through the application of carefully controlled RF transmissions, improving contaminant flow characteristics and facilitating separation and removal from subsurface soils. The paper outlines advantages and limitations of RF remediation, process operations, general technology considerations, low permeability media considerations, commercial availability, and costs. Two case histories of RF remediation are briefly summarized. 13 refs., 10 figs.

United States Special Operations Command’s Foreign Language Proficiency Bonus at ILR 1/1+: Initial Review and Recommended Changes to Improve Results and Lower Cost

DTIC Science & Technology

2012-10-01

to be useful for proficiency development, and with the limited research available, Doughty found that instructed language learners moved further...absolute speaking proficiency in languages taught at the Foreign Service Institute. Arlington, VA: Author. SOFLO Support Project USSOCOM’s Foreign...on language and linguistics 1999: Language in our time: Bilingual education and official English , ebonics and standard English , immigration and the Unz

Intranets: virtual procedure manuals for the pathology lab.

PubMed

Ruby, S G; Krempel, G

1998-08-01

A novel system exists for replacing standard written operation manuals using a computerized PC-based peer-to-peer network. The system design is based on commonly available hardware and software and utilizes existing equipment to minimize implementation expense. The system is relatively easy to implement and maintain, involves minimal training, and should quickly become a financial asset. In addition, such a system can improve access to laboratory procedure manuals so that resources can be better used on a daily basis.

Drainage basin characteristics from ERTS data

NASA Technical Reports Server (NTRS)

Hollyday, E. F. (Principal Investigator)

1975-01-01

The author has identified the following significant results. ERTS-derived measurements of forests, riparian vegetation, open water, and combined agricultural and urban land use were added to an available matrix of map-derived basin characteristics. The matrix of basin characteristics was correlated with 40 stream flow characteristics by multiple regression techniques. Fifteen out of the 40 equations were improved. If the technique can be transferred to other physiographic regions in the nation, the opportunity exists for a potential annual savings in operations of about $250,000.

Enhanced optical nonlinearities in the near-infrared using III-nitride heterostructures coupled to metamaterials

DOE PAGES

Wolf, Omri; Allerman, Andrew A.; Ma, Xuedan; ...

2015-10-15

We use planar metamaterial resonators to enhance, by more than two orders of magnitude, the optical second harmonic generation, in the near infrared, obtained from intersubband transitions in III-Nitride heterostructures. The improvement arises from two factors: employing an asymmetric double quantum well design and aligning the resonators’ cross-polarized resonances with the intersubband transition energies. The resulting nonlinear metamaterial operates at wavelengths where single photon detection is available, and represents a new class of sources for quantum photonics related phenomena.

Automated Data Aggregation for Time-Series Analysis: Study Case on Anaesthesia Data Warehouse.

PubMed

Lamer, Antoine; Jeanne, Mathieu; Ficheur, Grégoire; Marcilly, Romaric

2016-01-01

Data stored in operational databases are not reusable directly. Aggregation modules are necessary to facilitate secondary use. They decrease volume of data while increasing the number of available information. In this paper, we present four automated engines of aggregation, integrated into an anaesthesia data warehouse. Four instances of clinical questions illustrate the use of those engines for various improvements of quality of care: duration of procedure, drug administration, assessment of hypotension and its related treatment.

From I.T. to information management with casemix data.

PubMed

Diers, D; Pelletier, D

2001-01-01

The Australian investment in technological support for the collection and analysis of hospital data has paid off in the creation of data depositories that can be used for system and policy analysis. Yet the inquiries that would inform decision for quality and efficiency improvement are made at the operational levels where there has not been equivalent investment in developing human capacity. This article suggests strategies and methods for using standard healthcare information that is now so much more readily available.

Aerial Command and Control Utilizing Wireless Meshed Networks in Support of Joint Tactical Coalition Operations

DTIC Science & Technology

2005-09-01

employed. This particular balloon design uses a flap, known as a kite , which functions as a sail to increase lift capability and improve airborne...stability. The kite increases the balloon’s lift capability to 800 pounds in 90- knot winds and enables the balloon position to be relatively...Thai airfield at Wing 2. This vehicle may also serve as a runner vehicle for the MCP node of the COASTS demonstration. A PRC-117 will be available

Dual nozzle aerodynamic and cooling analysis study

NASA Technical Reports Server (NTRS)

Meagher, G. M.

1981-01-01

Analytical models to predict performance and operating characteristics of dual nozzle concepts were developed and improved. Aerodynamic models are available to define flow characteristics and bleed requirements for both the dual throat and dual expander concepts. Advanced analytical techniques were utilized to provide quantitative estimates of the bleed flow, boundary layer, and shock effects within dual nozzle engines. Thermal analyses were performed to define cooling requirements for baseline configurations, and special studies of unique dual nozzle cooling problems defined feasible means of achieving adequate cooling.

Application of Automated Data-Scanning Techniques to U.S. Army Directorates of Engineering and Housing Operations

DTIC Science & Technology

1991-09-01

back of a paper or plastic card. A decoder reads the flux reversals and translates them into letters and numbers for processing by a computer. The best...read without decoding. In the past 3 or 4 years, OCR technology has been improved significantly due mostly to the availability of relatively low-cost...transaction readers, and hand- held readers. Page readers scan pages of text either directly from paper or from digitized images of documents stored in the

Standard Operating Procedures (SOPs) for Evaluating the Heart in Preclinical Studies of Duchenne Muscular Dystrophy.

PubMed

Duan, Dongsheng; Rafael-Fortney, Jill A; Blain, Alison; Kass, David A; McNally, Elizabeth M; Metzger, Joseph M; Spurney, Christopher F; Kinnett, Kathi

2016-02-01

A recent working group meeting focused on contemporary cardiac issues in Duchenne muscular dystrophy (DMD) was hosted by the National Heart, Lung, and Blood Institute in collaboration with the Parent Project Muscular Dystrophy. An outcome of this meeting was to provide freely available detailed protocols for preclinical animal studies. The goal of these protocols is to improve the quality and reproducibility of cardiac preclinical studies aimed at developing new therapeutics for the prevention and treatment of DMD cardiomyopathy.

Landsat Program

NASA Technical Reports Server (NTRS)

Markham, Brian L.; Arvidson, Terry; Barsi, Julia A.; Choate, Michael; Kaita, Edward; Levy, Raviv; Lubke, Mark; Masek, Jeffrey G.

2016-01-01

Landsat initiated the revolution in moderate resolution Earth remote sensing in the 1970s. With seven successful missions over 40+ years, Landsat has documented - and continues to document - the global Earth land surface and its evolution. The Landsat missions and sensors have evolved along with the technology from a demonstration project in the analog world of visual interpretation to an operational mission in the digital world, with incremental improvements along the way in terms of spectral, spatial, radiometric and geometric performance as well as acquisition strategy, data availability, and products.

Assessing rural small community water supply in Limpopo, South Africa: water service benchmarks and reliability.

PubMed

Majuru, Batsirai; Jagals, Paul; Hunter, Paul R

2012-10-01

Although a number of studies have reported on water supply improvements, few have simultaneously taken into account the reliability of the water services. The study aimed to assess whether upgrading water supply systems in small rural communities improved access, availability and potability of water by assessing the water services against selected benchmarks from the World Health Organisation and South African Department of Water Affairs, and to determine the impact of unreliability on the services. These benchmarks were applied in three rural communities in Limpopo, South Africa where rudimentary water supply services were being upgraded to basic services. Data were collected through structured interviews, observations and measurement, and multi-level linear regression models were used to assess the impact of water service upgrades on key outcome measures of distance to source, daily per capita water quantity and Escherichia coli count. When the basic system was operational, 72% of households met the minimum benchmarks for distance and water quantity, but only 8% met both enhanced benchmarks. During non-operational periods of the basic service, daily per capita water consumption decreased by 5.19l (p<0.001, 95% CI 4.06-6.31) and distances to water sources were 639 m further (p ≤ 0.001, 95% CI 560-718). Although both rudimentary and basic systems delivered water that met potability criteria at the sources, the quality of stored water sampled in the home was still unacceptable throughout the various service levels. These results show that basic water services can make substantial improvements to water access, availability, potability, but only if such services are reliable. Copyright © 2012 Elsevier B.V. All rights reserved.

CIB: an improved communication architecture for real-time monitoring of aerospace materials, instruments, and sensors on the ISS.

PubMed

Krasowski, Michael J; Prokop, Norman F; Flatico, Joseph M; Greer, Lawrence C; Jenkins, Phillip P; Neudeck, Philip G; Chen, Liangyu; Spina, Danny C

2013-01-01

The Communications Interface Board (CIB) is an improved communications architecture that was demonstrated on the International Space Station (ISS). ISS communication interfaces allowing for real-time telemetry and health monitoring require a significant amount of development. The CIB simplifies the communications interface to the ISS for real-time health monitoring, telemetry, and control of resident sensors or experiments. With a simpler interface available to the telemetry bus, more sensors or experiments may be flown. The CIB accomplishes this by acting as a bridge between the ISS MIL-STD-1553 low-rate telemetry (LRT) bus and the sensors allowing for two-way command and telemetry data transfer. The CIB was designed to be highly reliable and radiation hard for an extended flight in low Earth orbit (LEO) and has been proven with over 40 months of flight operation on the outside of ISS supporting two sets of flight experiments. Since the CIB is currently operating in flight on the ISS, recent results of operations will be provided. Additionally, as a vehicle health monitoring enabling technology, an overview and results from two experiments enabled by the CIB will be provided. Future applications for vehicle health monitoring utilizing the CIB architecture will also be discussed.

National Space Transportation System (NSTS) technology needs

NASA Technical Reports Server (NTRS)

Winterhalter, David L.; Ulrich, Kimberly K.

1990-01-01

The National Space Transportation System (NSTS) is one of the Nation's most valuable resources, providing manned transportation to and from space in support of payloads and scientific research. The NSTS program is currently faced with the problem of hardware obsolescence, which could result in unacceptable schedule and cost impacts to the flight program. Obsolescence problems occur because certain components are no longer being manufactured or repair turnaround time is excessive. In order to achieve a long-term, reliable transportation system that can support manned access to space through 2010 and beyond, NASA must develop a strategic plan for a phased implementation of enhancements which will satisfy this long-term goal. The NSTS program has initiated the Assured Shuttle Availability (ASA) project with the following objectives: eliminate hardware obsolescence in critical areas, increase reliability and safety of the vehicle, decrease operational costs and turnaround time, and improve operational capability. The strategy for ASA will be to first meet the mandatory needs - keep the Shuttle flying. Non-mandatory changes that will improve operational capability and enhance performance will then be considered if funding is adequate. Upgrade packages should be developed to install within designated inspection periods, grouped in a systematic approach to reduce cost and schedule impacts, and allow the capability to provide a Block 2 Shuttle (Phase 3).

CIB: An Improved Communication Architecture for Real-Time Monitoring of Aerospace Materials, Instruments, and Sensors on the ISS

PubMed Central

Krasowski, Michael J.; Prokop, Norman F.; Flatico, Joseph M.; Greer, Lawrence C.; Jenkins, Phillip P.; Neudeck, Philip G.; Chen, Liangyu; Spina, Danny C.

2013-01-01

The Communications Interface Board (CIB) is an improved communications architecture that was demonstrated on the International Space Station (ISS). ISS communication interfaces allowing for real-time telemetry and health monitoring require a significant amount of development. The CIB simplifies the communications interface to the ISS for real-time health monitoring, telemetry, and control of resident sensors or experiments. With a simpler interface available to the telemetry bus, more sensors or experiments may be flown. The CIB accomplishes this by acting as a bridge between the ISS MIL-STD-1553 low-rate telemetry (LRT) bus and the sensors allowing for two-way command and telemetry data transfer. The CIB was designed to be highly reliable and radiation hard for an extended flight in low Earth orbit (LEO) and has been proven with over 40 months of flight operation on the outside of ISS supporting two sets of flight experiments. Since the CIB is currently operating in flight on the ISS, recent results of operations will be provided. Additionally, as a vehicle health monitoring enabling technology, an overview and results from two experiments enabled by the CIB will be provided. Future applications for vehicle health monitoring utilizing the CIB architecture will also be discussed. PMID:23983621

Chemical and Physical Sensing in the Petroleum Industry

NASA Astrophysics Data System (ADS)

Disko, Mark

2008-03-01

World-scale oil, gas and petrochemical production relies on a myriad of advanced technologies for discovering, producing, transporting, processing and distributing hydrocarbons. Sensing systems provide rapid and targeted information that can be used for expanding resources, improving product quality, and assuring environmentally sound operations. For example, equipment such as reactors and pipelines can be operated with high efficiency and safety with improved chemical and physical sensors for corrosion and hydrocarbon detection. At the interface between chemical engineering and multiphase flow physics, ``multi-scale'' phenomena such as catalysis and heat flow benefit from new approaches to sensing and data modeling. We are combining chemically selective micro-cantilevers, fiber optic sensing, and acoustic monitoring with statistical data fusion approaches to maximize control information. Miniaturized analyzers represent a special opportunity, including the nanotech-based quantum cascade laser systems for mid-infrared spectroscopy. Specific examples for use of these new micro-systems include rapid monocyclic aromatic molecule identification and measurement under ambient conditions at weight ppb levels. We see promise from emerging materials and devices based on nanotechnology, which can one day be available at modest cost for impact in existing operations. Controlled surface energies and emerging chemical probes hold the promise for reduction in greenhouse gas emissions for current fuels and future transportation and energy technologies.

On sufficient statistics of least-squares superposition of vector sets.

PubMed

Konagurthu, Arun S; Kasarapu, Parthan; Allison, Lloyd; Collier, James H; Lesk, Arthur M

2015-06-01

The problem of superposition of two corresponding vector sets by minimizing their sum-of-squares error under orthogonal transformation is a fundamental task in many areas of science, notably structural molecular biology. This problem can be solved exactly using an algorithm whose time complexity grows linearly with the number of correspondences. This efficient solution has facilitated the widespread use of the superposition task, particularly in studies involving macromolecular structures. This article formally derives a set of sufficient statistics for the least-squares superposition problem. These statistics are additive. This permits a highly efficient (constant time) computation of superpositions (and sufficient statistics) of vector sets that are composed from its constituent vector sets under addition or deletion operation, where the sufficient statistics of the constituent sets are already known (that is, the constituent vector sets have been previously superposed). This results in a drastic improvement in the run time of the methods that commonly superpose vector sets under addition or deletion operations, where previously these operations were carried out ab initio (ignoring the sufficient statistics). We experimentally demonstrate the improvement our work offers in the context of protein structural alignment programs that assemble a reliable structural alignment from well-fitting (substructural) fragment pairs. A C++ library for this task is available online under an open-source license.

Advanced Technology Spark-Ignition Aircraft Piston Engine Design Study

NASA Technical Reports Server (NTRS)

Stuckas, K. J.

1980-01-01

The advanced technology, spark ignition, aircraft piston engine design study was conducted to determine the improvements that could be made by taking advantage of technology that could reasonably be expected to be made available for an engine intended for production by January 1, 1990. Two engines were proposed to account for levels of technology considered to be moderate risk and high risk. The moderate risk technology engine is a homogeneous charge engine operating on avgas and offers a 40% improvement in transportation efficiency over present designs. The high risk technology engine, with a stratified charge combustion system using kerosene-based jet fuel, projects a 65% improvement in transportation efficiency. Technology enablement program plans are proposed herein to set a timetable for the successful integration of each item of required advanced technology into the engine design.

Rehabilitation of the paralysed or lax lower eyelid using a graft of conchal cartilage.

PubMed

Krastinova, D; Franchi, G; Kelly, M B H; Chabolle, F

2002-01-01

Excessive laxity of the tarso-ligamentous sling of the lower eyelid may be caused by inadequate muscular support (resulting from injury to the muscle, facial palsy or senile degeneration) or prolonged mechanical distension (exophthalmia). Numerous techniques have been devised for functional reconstruction of the distended lower eyelid, based upon the principle that restoring the lower eyelid to its anatomical position will improve lacrimal transit andre-establish its natural protective function. We now use an autologous conchal cartilage graft to treat the distended or atonic lower eyelid. We review our results in a retrospective study of 20 patients, and aim to identify the indications for this procedure and to evaluate its advantages and disadvantages relative to other existing methods. All of our patients reported functional improvement after the operation in terms of decreased dry-eye symptoms, less epiphora and a decline in keratitis and conjunctivitis. All patients also reported a visible cosmetic improvement postoperatively. The major drawback of this operation is the partial loss of the visual field when looking down, due to the limited lowering of the lower eyelid. The stability of our results compares favourably with that achieved using other currently available techniques. We conclude that autologous conchal cartilage grafting is an effective procedure for improving both the function and the appearance of the atonic lower eyelid. Copyright 2002 The British Association of Plastic Surgeons.

A GLM Post-processor to Adjust Ensemble Forecast Traces

NASA Astrophysics Data System (ADS)

Thiemann, M.; Day, G. N.; Schaake, J. C.; Draijer, S.; Wang, L.

2011-12-01

The skill of hydrologic ensemble forecasts has improved in the last years through a better understanding of climate variability, better climate forecasts and new data assimilation techniques. Having been extensively utilized for probabilistic water supply forecasting, interest is developing to utilize these forecasts in operational decision making. Hydrologic ensemble forecast members typically have inherent biases in flow timing and volume caused by (1) structural errors in the models used, (2) systematic errors in the data used to calibrate those models, (3) uncertain initial hydrologic conditions, and (4) uncertainties in the forcing datasets. Furthermore, hydrologic models have often not been developed for operational decision points and ensemble forecasts are thus not always available where needed. A statistical post-processor can be used to address these issues. The post-processor should (1) correct for systematic biases in flow timing and volume, (2) preserve the skill of the available raw forecasts, (3) preserve spatial and temporal correlation as well as the uncertainty in the forecasted flow data, (4) produce adjusted forecast ensembles that represent the variability of the observed hydrograph to be predicted, and (5) preserve individual forecast traces as equally likely. The post-processor should also allow for the translation of available ensemble forecasts to hydrologically similar locations where forecasts are not available. This paper introduces an ensemble post-processor (EPP) developed in support of New York City water supply operations. The EPP employs a general linear model (GLM) to (1) adjust available ensemble forecast traces and (2) create new ensembles for (nearby) locations where only historic flow observations are available. The EPP is calibrated by developing daily and aggregated statistical relationships form historical flow observations and model simulations. These are then used in operation to obtain the conditional probability density function (PDF) of the observations to be predicted, thus jointly adjusting individual ensemble members. These steps are executed in a normalized transformed space ('z'-space) to account for the strong non-linearity in the flow observations involved. A data window centered on each calibration date is used to minimize impacts from sampling errors and data noise. Testing on datasets from California and New York suggests that the EPP can successfully minimize biases in ensemble forecasts, while preserving the raw forecast skill in a 'days to weeks' forecast horizon and reproducing the variability of climatology for 'weeks to years' forecast horizons.

Industrial Energy Training and Certification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glatt, Sandy; Cox, Daryl; Nimbalkar, Sachin U.

Compressed air systems, ammonia refrigeration systems, chilled water systems, steam systems, process heating systems, combined heat and power systems, pump systems and fan systems are major industrial energy systems commonly found in manufacturing facilities. Efficiency of these systems contributes significantly to whole facilities' energy performance. On the national, even international level, well-structured training and highly recognized certification programs help develop a highly-skilled and qualified workforce to maintain and improve facilities' energy performance, particularly as technologies within these systems become more advanced. The purpose of this paper is to review currently available training and certification programs focusing on these systems andmore » to identify the gap between market's needs and currently available programs. Three major conclusions are: first, most training programs focus on operations, maintenance, safety and design although some briefly touch the energy performance aspect; second, except CRES by RETA and PSA Certificate and PSAP Master Certification by HI, no other certifications had been found emphasizing on knowledge and skills for improving and maintaining these systems' energy performance; third, developing energy efficiency focused training and ANSI accredited certification programs on these energy systems will fill the gap between market's needs and currently available programs.« less

Industrial Energy Training and Certification

DOE PAGES

Glatt, Sandy; Cox, Daryl; Nimbalkar, Sachin U.; ...

2017-11-01

Compressed air systems, ammonia refrigeration systems, chilled water systems, steam systems, process heating systems, combined heat and power systems, pump systems and fan systems are major industrial energy systems commonly found in manufacturing facilities. Efficiency of these systems contributes significantly to whole facilities' energy performance. On the national, even international level, well-structured training and highly recognized certification programs help develop a highly-skilled and qualified workforce to maintain and improve facilities' energy performance, particularly as technologies within these systems become more advanced. The purpose of this paper is to review currently available training and certification programs focusing on these systems andmore » to identify the gap between market's needs and currently available programs. Three major conclusions are: first, most training programs focus on operations, maintenance, safety and design although some briefly touch the energy performance aspect; second, except CRES by RETA and PSA Certificate and PSAP Master Certification by HI, no other certifications had been found emphasizing on knowledge and skills for improving and maintaining these systems' energy performance; third, developing energy efficiency focused training and ANSI accredited certification programs on these energy systems will fill the gap between market's needs and currently available programs.« less

31 CFR 206.10 - Operation of and payments from the Cash Management Improvements Fund.

Code of Federal Regulations, 2010 CFR

2010-07-01

... SERVICE MANAGEMENT OF FEDERAL AGENCY RECEIPTS, DISBURSEMENTS, AND OPERATION OF THE CASH MANAGEMENT IMPROVEMENTS FUND § 206.10 Operation of and payments from the Cash Management Improvements Fund. (a) The Cash... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Operation of and payments from the...

76 FR 80314 - National Emission Standards for Hazardous Air Pollutants: Area Source Standards for Prepared...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-23

... operating instructions, if available, or standard operating procedures must be developed by the facility... operating instructions, if available, or standard operating procedures must be developed by the facility... standard operating procedures developed by the prepared feeds manufacturer be required as part of the...

77 FR 9961 - Notice of Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-21

... accordance with the provisions of 36 CFR 9.17, Randy Elliott has filed a proposed plan of operations to conduct mining operations on lands embracing Mineral Survey No. 923, patented mineral property within Wrangell-St. Elias National Park and Preserve. Public Availability: This plan of operations is available...

Transparency, usability, and reproducibility: Guiding principles for improving comparative databases using primates as examples.

PubMed

Borries, Carola; Sandel, Aaron A; Koenig, Andreas; Fernandez-Duque, Eduardo; Kamilar, Jason M; Amoroso, Caroline R; Barton, Robert A; Bray, Joel; Di Fiore, Anthony; Gilby, Ian C; Gordon, Adam D; Mundry, Roger; Port, Markus; Powell, Lauren E; Pusey, Anne E; Spriggs, Amanda; Nunn, Charles L

2016-09-01

Recent decades have seen rapid development of new analytical methods to investigate patterns of interspecific variation. Yet these cutting-edge statistical analyses often rely on data of questionable origin, varying accuracy, and weak comparability, which seem to have reduced the reproducibility of studies. It is time to improve the transparency of comparative data while also making these improved data more widely available. We, the authors, met to discuss how transparency, usability, and reproducibility of comparative data can best be achieved. We propose four guiding principles: 1) data identification with explicit operational definitions and complete descriptions of methods; 2) inclusion of metadata that capture key characteristics of the data, such as sample size, geographic coordinates, and nutrient availability (for example, captive versus wild animals); 3) documentation of the original reference for each datum; and 4) facilitation of effective interactions with the data via user friendly and transparent interfaces. We urge reviewers, editors, publishers, database developers and users, funding agencies, researchers publishing their primary data, and those performing comparative analyses to embrace these standards to increase the transparency, usability, and reproducibility of comparative studies. © 2016 Wiley Periodicals, Inc.

Diving injuries of the cervical spine in amateur divers.

PubMed

Korres, Demetrios S; Benetos, Ioannis S; Themistocleous, George S; Mavrogenis, Andreas F; Nikolakakos, Leonidas; Liantis, Panagiotis T

2006-01-01

Diving injuries are the cause of potentially devastating trauma, primarily affecting the cervical spine. Our purpose was to describe our experience with diving injuries treatment. Retrospective review. Twenty patients with diving injuries. Using the American Spinal Injury Association (ASIA) impairment scales as the primary outcome measure, the patients' neurological status before and after treatment was assessed. In this way we were able to draw conclusions about neurological improvement or deterioration in response to conservative or operative treatment. We retrospectively reviewed 20 patients with diving injuries of the cervical spine who were admitted to our institute over a 34-year period from 1970 until 2004. The typical patient profile was of a young, healthy, athletic male who suffered an injury to the cervical spine after diving into shallow water. The number of cases corresponds to 2.6% of all admitted cervical spine injuries. All injures occurred between May and September. The most commonly fractured vertebrae were C5 and C6. Four patients were treated operatively and 16 conservatively. The indications for surgical treatment were posttraumatic instability and persistent neurological deficit. The mean follow-up of the patients was 17 years. Five patients died within the first month of their hospitalization and 1 patient died 1 year after his injury. Of the 14 patients who were available for follow-up 5 years past injury time, 6 improved neurologically and 8 remained unchanged in relation to their neurology upon admission. Of the 11 patients who were available for follow-up 10 years past injury time, 9 remained neurologically unchanged, 1 deteriorated, and 1 improved in relation to their neurology in the 5-year follow-up. Diving injuries of the cervical spine demonstrate high mortality and morbidity rates. Recovery depends on the severity of the initial neurological damage. Conservative treatment is justified in specific patients and can lead to improvement of the initial neurological deficit.

Towards improving the NASA standard soil moisture retrieval algorithm and product

NASA Astrophysics Data System (ADS)

Mladenova, I. E.; Jackson, T. J.; Njoku, E. G.; Bindlish, R.; Cosh, M. H.; Chan, S.

2013-12-01

Soil moisture mapping using passive-based microwave remote sensing techniques has proven to be one of the most effective ways of acquiring reliable global soil moisture information on a routine basis. An important step in this direction was made by the launch of the Advanced Microwave Scanning Radiometer on the NASA's Earth Observing System Aqua satellite (AMSR-E). Along with the standard NASA algorithm and operational AMSR-E product, the easy access and availability of the AMSR-E data promoted the development and distribution of alternative retrieval algorithms and products. Several evaluation studies have demonstrated issues with the standard NASA AMSR-E product such as dampened temporal response and limited range of the final retrievals and noted that the available global passive-based algorithms, even though based on the same electromagnetic principles, produce different results in terms of accuracy and temporal dynamics. Our goal is to identify the theoretical causes that determine the reduced sensitivity of the NASA AMSR-E product and outline ways to improve the operational NASA algorithm, if possible. Properly identifying the underlying reasons that cause the above mentioned features of the NASA AMSR-E product and differences between the alternative algorithms requires a careful examination of the theoretical basis of each approach. Specifically, the simplifying assumptions and parametrization approaches adopted by each algorithm to reduce the dimensionality of unknowns and characterize the observing system. Statistically-based error analyses, which are useful and necessary, provide information on the relative accuracy of each product but give very little information on the theoretical causes, knowledge that is essential for algorithm improvement. Thus, we are currently examining the possibility of improving the standard NASA AMSR-E global soil moisture product by conducting a thorough theoretically-based review of and inter-comparisons between several well established global retrieval techniques. A detailed discussion focused on the theoretical basis of each approach and algorithms sensitivity to assumptions and parametrization approaches will be presented. USDA is an equal opportunity provider and employer.

Improving INPE'S balloon ground facilities for operation of the protoMIRAX experiment

NASA Astrophysics Data System (ADS)

Mattiello-Francisco, F.; Rinke, E.; Fernandes, J. O.; Cardoso, L.; Cardoso, P.; Braga, J.

2014-10-01

The system requirements for reusing the scientific balloon ground facilities available at INPE were a challenge to the ground system engineers involved in the protoMIRAX X-ray astronomy experiment. A significant effort on software updating was required for the balloon ground station. Considering that protoMIRAX is a pathfinder for the MIRAX satellite mission, a ground infrastructure compatible with INPE's satellite operation approach would be useful and highly recommended to control and monitor the experiment during the balloon flights. This approach will make use of the SATellite Control System (SATCS), a software-based architecture developed at INPE for satellite commanding and monitoring. SATCS complies with particular operational requirements of different satellites by using several customized object-oriented software elements and frameworks. We present the ground solution designed for protoMIRAX operation, the Control and Reception System (CRS). A new server computer, properly configured with Ethernet, has extended the existing ground station facilities with switch, converters and new software (OPS/SERVER) in order to support the available uplink and downlink channels being mapped to TCP/IP gateways required by SATCS. Currently, the CRS development is customizing the SATCS for the kernel functions of protoMIRAX command and telemetry processing. Design-patterns, component-based libraries and metadata are widely used in the SATCS in order to extend the frameworks to address the Packet Utilization Standard (PUS) for ground-balloon communication, in compliance with the services provided by the data handling computer onboard the protoMIRAX balloon.

Analysis of Electric Power Board of Chattanooga Smart Grid Investment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Starke, Michael; Ollis, Ben; Glass, Jim

The deployment of a Smart Grid within the EPB electrical system has brought significant value to EPB customers and to EPB operations. The Smart Grid implementation has permitted the capability to automate many of the existing systems, increasing the overall efficiency and decreasing round trip time for many required operation functions. This has both reduced the cost of operations and increased the reliability of customer service. This boost in performance can be primarily linked to two main components: the communication network and the availability of data. The existence of a fiber communication backbone has opened numerous opportunities for EPB. Largemore » data sets from remote devices can be continuously polled and used to compute numerous metrics. The speed of communication has provided a pathway to sophisticated distribution automation that would not otherwise be possible. The data have been shown to provide a much broader view of the actual electrical system that was not previously available, opening many new opportunities in data analytics. This report documents many of the existing systems and operational features of the EPB system. Many of these systems have seen significant improvement with the deployment of Smart Grid technologies. The research behind this report found that in some cases, the value was directly computable or estimable for these enhancements. Currently, several ongoing research topics are under investigation within EPB. Through a grant from TVA, EPB is currently installing a 1.3MW solar photovoltaic system, which will be the first-generation asset owned by EPB.« less

A Compact, Continuous Adiabatic Demagnetization Refrigerator with High Heat Sink Temperature

NASA Technical Reports Server (NTRS)

Shirron, P. J.; Canavan, E. R.; DiPirro, M. J.; Jackson, M.; Tuttle, J. G.

2003-01-01

In the continuous adiabatic demagnetization refrigerator (ADR), the existence of a constant temperature stage attached to the load breaks the link between the requirements of the load (usually a detector array) and the operation of the ADR. This allows the ADR to be cycled much faster, which yields more than an order of magnitude improvement in cooling power density over single-shot ADRs. Recent effort has focused on developing compact, efficient higher temperature stages. An important part of this work has been the development of passive gas-gap heat switches that transition (from conductive to insulating) at temperatures around 1 K and 4 K without the use of an actively heated getter. We have found that by carefully adjusting available surface area and the number of He-3 monolayers, gas-gap switches can be made to operate passively. Passive operation greatly reduces switching time and eliminates an important parasitic heat load. The current four stage ADR provides 6 micro W of cooling at 50 mK (21 micro W at 100 mK) and weighs less than 8 kg. It operates from a 4.2 K heat sink, which can be provided by an unpumped He bath or many commercially available mechanical cryocoolers. Reduction in critical current with temperature in our fourth stage NbTi magnet presently limits the maximum temperature of our system to approx. 5 K. We are developing compact, low-current Nb3Sn magnets that will raise the maximum heat sink temperature to over 10 K.

Safety aspects of whole-body cryochamber and cryosauna operation

NASA Astrophysics Data System (ADS)

Agnieszka, Piotrowska

2017-12-01

Interest in low temperature treatment is constantly increasing. Whole-body cryotherapy (WBC) devices are becoming available not only in medical centers but also in local gyms and spa centers. A new group of users are professional sport clubs where 3-minutes session of whole-body cryotherapy is post-training procedure to improve and speed up the recovery process. There are four different types of WBC devices available on the market and offered to commercial (non-medical) users. The American and European market is dominated by two of them: classic cryochambers and cryosaunas. Both constructions are supplied with liquid nitrogen. Low temperature inside classic cryochamber is produced by evaporating of liquid nitrogen in two or more heat exchangers. There is never a direct contact between user and cryogenic medium in any of system operation mode (closed supply system). Cryosauna is cooled down by filling with cold vapor of liquid nitrogen. Supply system is considered open because it allows for direct contact between user and cryogenic medium. Open supply system of cryosauna is primary and most questionable issue of its operational safety, particularly after tragic accident in October 2015. This paper presents the comparative analysis of classic cryochamber and cryosauna from safety point of view. Both devices have been analyzes and tested on existing systems in operation. Paper gives detailed analysis of constructions, supply systems and working parameters. Special attention has been focused to problem of oxygen deficiency hazard. Different failure or accident scenarios have been analyzed and discussed.

Quality of surgical care in hospitals providing internship training in Kenya: a cross sectional survey.

PubMed

Mwinga, Stephen; Kulohoma, Colette; Mwaniki, Paul; Idowu, Rachel; Masasabi, John; English, Mike

2015-02-01

To evaluate services in hospitals providing internship training to graduate doctors in Kenya. A survey of 22 internship training hospitals was conducted. Availability of key resources spanning infrastructure, personnel, equipment and drugs was assessed by observation. Outcomes and process of care for pre-specified priority conditions (head injury, chest injury, fractures, burns and acute abdomen) were evaluated by auditing case records. Each hospital had at least one consultant surgeon. Scheduled surgical outpatient clinics, major ward rounds and elective (half day) theatre lists were provided once per week in 91%, 55% and 9%, respectively. In all other hospitals, these were conducted twice weekly. Basic drugs were not always available (e.g. gentamicin, morphine and pethidine in 50%, injectable antistaphylococcal penicillins in 5% hospitals). Fewer than half of hospitals had all resources needed to provide oxygen. One hundred and forty-five of 956 cases evaluated underwent operations under general or spinal anaesthesia. We found operation notes for 99% and anaesthetic records for 72%. Pre-operatively measured vital signs were recorded in 80% of cases, and evidence of consent to operation was found in 78%. Blood loss was documented in only one case and sponge and instrument counts in 7%. Evaluation of surgical services would be improved by development and dissemination of clear standards of care. This survey suggests that internship hospitals may be poorly equipped and documented care suggests inadequacies in quality and training. © 2014 The Authors. Tropical Medicine & International Health Published by John Wiley & Sons Ltd.

Increasing the Cost-efficiency of the DSN

NASA Technical Reports Server (NTRS)

Statman, Joseph I.; Berner, Jeff B.

2008-01-01

JPL has operated the Deep Space Network (DSN) on behalf of NASA since the 1960's. Over the last two decades, the DSN budget has generally declined in real-year dollars while the aging assets required more attention, and the missions became more complex. As a result, the budget has been increasingly consumed by Operations and Maintenance (O and M), significantly reducing the funding wedge available for technology investment and for enhancing the DSN capability and capacity. Responding to this budget squeeze, the DSN launched an effort to improve the cost-efficiency of the O and M. In this paper we: Analyze the components of O&M. We note for example that, for the DSN, less than 20% of the staff engage in the traditional human-in-front-a-console role, so any effort to increase the cost efficiency must go beyond reducing the number of "Real-time operators." Explain the underlying organizational and cultural structures. Any cost-efficiency activities changes either accept, or carefully modify these structures. For example, the DSN O&M is based on the concept that there are three nearly identical antenna complexes separated by approximately 1200 in latitude and that each antenna complex is operated by a different contractor (driven by international agreements). Explore planned changes in the customer interface, e.g. web-based automated scheduling, and the processes required for a transition. Changes have to be evaluated in the larger end-to-end context, e.g. do the changes provide a net cost-efficiency for the DSN and the missions, or do they merely shift cost from the DSN to the missions. Consider possible significant changes in real-time pass management, e.g. full-remoting of operations, and lights-dim operations, while maintaining (or improving) the performance metrics of the DSN. Investigate how procedural and administrative changes could increase cost-efficiency, in conjunction with changes in the customer interfaces and real-time pass management. Examples would be handling of inter-governmental agreements, improved sharing of resources with other agencies, and better use of commercial (rather than government) resources

Effects of digital countdown timer on intersection safety and efficiency: A systematic review.

PubMed

Fu, Chuanyun; Zhang, Yaping; Qi, Weiwei; Cheng, Shaowu

2016-01-01

To investigate the available evidence referring to the effectiveness of digital countdown timers (DCTs) in improving the safety and operational efficiency of signalized intersection. A systematic review was performed according to the Preferred Reporting Items for Systematic Reviews and Meta-Analysis (PRISMA) statement guidelines. Relevant literature was searched from electronic databases using key terms. Based on study selection and methodological quality assessment, 14 studies were included in the review. Findings of the studies were synthesized in a narrative analysis. Three types of DCT had different effects on intersection safety and operational efficiency. Green signal countdown timers (GSCTs) reduced red light violations, type I dilemma zone distributions, and rear-end collision likelihood but increased crossing after yellow onset and had mixed impacts on type II dilemma zone distributions and intersection capacity. In contrast, red signal countdown timers (RSCTs) increased intersection capacity, although their effectiveness in reducing red light violations dissipated over time. Likewise, continuous countdown timers (CCTs) significantly enhanced intersection capacity but had mixed influences on red light violations and crossing after yellow onset. Due to the limited and inconsistent evidence regarding DCTs' effects on intersection safety and efficiency, it is not sufficient to recommend any type of DCT to be installed at signalized intersections to improve safety and operational efficiency. Nevertheless, it is apparent that both RSCTs and CCTs enhance intersection capacity, though their impacts on intersection safety are unclear. Future studies need to further verify those anticipated safe and operational benefits of DCTs with enriched field observation data.

Data Assimilation in the Solar Wind: Challenges and First Results.

PubMed

Lang, Matthew; Browne, Philip; van Leeuwen, Peter Jan; Owens, Mathew

2017-11-01

Data assimilation (DA) is used extensively in numerical weather prediction (NWP) to improve forecast skill. Indeed, improvements in forecast skill in NWP models over the past 30 years have directly coincided with improvements in DA schemes. At present, due to data availability and technical challenges, DA is underused in space weather applications, particularly for solar wind prediction. This paper investigates the potential of advanced DA methods currently used in operational NWP centers to improve solar wind prediction. To develop the technical capability, as well as quantify the potential benefit, twin experiments are conducted to assess the performance of the Local Ensemble Transform Kalman Filter (LETKF) in the solar wind model ENLIL. Boundary conditions are provided by the Wang-Sheeley-Arge coronal model and synthetic observations of density, temperature, and momentum generated every 4.5 h at 0.6 AU. While in situ spacecraft observations are unlikely to be routinely available at 0.6 AU, these techniques can be applied to remote sensing of the solar wind, such as with Heliospheric Imagers or interplanetary scintillation. The LETKF can be seen to improve the state at the observation location and advect that improvement toward the Earth, leading to an improvement in forecast skill in near-Earth space for both the observed and unobserved variables. However, sharp gradients caused by the analysis of a single observation in space resulted in artificial wavelike structures being advected toward Earth. This paper is the first attempt to apply DA to solar wind prediction and provides the first in-depth analysis of the challenges and potential solutions.

Data Assimilation in the Solar Wind: Challenges and First Results

NASA Astrophysics Data System (ADS)

Lang, Matthew; Browne, Philip; van Leeuwen, Peter Jan; Owens, Mathew

2017-11-01

Data assimilation (DA) is used extensively in numerical weather prediction (NWP) to improve forecast skill. Indeed, improvements in forecast skill in NWP models over the past 30 years have directly coincided with improvements in DA schemes. At present, due to data availability and technical challenges, DA is underused in space weather applications, particularly for solar wind prediction. This paper investigates the potential of advanced DA methods currently used in operational NWP centers to improve solar wind prediction. To develop the technical capability, as well as quantify the potential benefit, twin experiments are conducted to assess the performance of the Local Ensemble Transform Kalman Filter (LETKF) in the solar wind model ENLIL. Boundary conditions are provided by the Wang-Sheeley-Arge coronal model and synthetic observations of density, temperature, and momentum generated every 4.5 h at 0.6 AU. While in situ spacecraft observations are unlikely to be routinely available at 0.6 AU, these techniques can be applied to remote sensing of the solar wind, such as with Heliospheric Imagers or interplanetary scintillation. The LETKF can be seen to improve the state at the observation location and advect that improvement toward the Earth, leading to an improvement in forecast skill in near-Earth space for both the observed and unobserved variables. However, sharp gradients caused by the analysis of a single observation in space resulted in artificial wavelike structures being advected toward Earth. This paper is the first attempt to apply DA to solar wind prediction and provides the first in-depth analysis of the challenges and potential solutions.

Use of real-time tools to support field operations of NSF's Lower Atmosphere Observing Facilities

NASA Astrophysics Data System (ADS)

Daniels, M.; Stossmeister, G.; Johnson, E.; Martin, C.; Webster, C.; Dixon, M.; Maclean, G.

2012-12-01

NCAR's Earth Observing Laboratory (EOL) operates Lower Atmosphere Observing Facilities (LAOF) for the scientific community, under sponsorship of the National Science Foundation. In order to obtain the highest quality dataset during field campaigns, real-time decision-making critically depends on the availability of timely data and reliable communications between field operations staff and instrument operators. EOL incorporates the latest technologies to monitor the health of instrumentation, facilitate remote operations of instrumentation and keep project participants abreast of changing conditions in the field. As the availability of bandwidth on mobile communication networks and the capabilities of their associated devices (smart phone, tablets, etc.) improved, so has the ability of researchers to respond to rapidly changing conditions and coordinate ever more detailed measurements from multiple remote fixed, portable and airborne platforms. This presentation will describe several new tools that EOL is making available to project investigators and how these tools are being used in a mobile computing environment to support enhanced data collection during field campaigns. LAOF platforms such as radars, aircraft, sondes, balloons and surface stations all rely on displays of real-time data for their operations. Data from sondes are ingested into the Global Telecommunications System (GTS) for assimilation into regional forecasting models that help guide project operations. Since many of EOL's projects occur around the globe and at the same time instrument complexity has increased, automated monitoring of instrumentation platforms and systems has become essential. Tools are being developed to allow remote instrument control of our suite of observing systems where feasible. The Computing, Data and Software (CDS) Facility of EOL develops and supports a Field Catalog used in field campaigns for nearly two decades. Today, the Field Catalog serves as a hub for the collection and browsing of field research products, related operational and forecast imagery, project documentation as well as tools for real-time decision-making, communication, mission planning and post analysis. Incorporation of new capabilities into the Field Catalog to support the mobile computing environment and devices has led to the development of new tools which will be described. EOL/CDS has also developed a customized Internet Relay Chat (IRC) chat system to enable communication between all project participants distributed across various land-based, shipboard and airborne remote sites. The CDS chat system has incorporated aspects of fault tolerance in order to handle intermittent communications links. NOAA and NASA have used this chat system for their field missions as well. These new tools were recently deployed in support of the Deep Convective Clouds and Chemistry (DC3) field campaign that took place May - June 2012 in the Central United States. This presentation will show examples of these real-time tools from recent projects. We will also describe some of the challenges, problems and surprises, as well as improvements that have been made to the tools. The capabilities of this system continue to advance, taking advantage of new technology and guided by our experience and feedback from users participating in field campaigns.

[Pedal bypass using venous allograft].

PubMed

Pluháčková, H; Staffa, R; Konečný, Z; Kříž, Z; Vlachovský, R

Pedal or distal crural bypass surgery for limb salvage is a method with very good long-term results. For patients in whom a suitable autologous venous graft is not available, the use of a venous allograft is an alternative procedure. A 68 years old man with ischaemic disease of lower extremities and gangrene of the left foot was admitted to our Centre in August 2014. He underwent percutaneous transluminal angioplasty of crural arteries of his left lower extremity. This, however, failed to improve peripheral circulation. The patient was then indicated for pedal or distal crural vascular reconstruction. Since no suitable autologous vein was available, distal bypass surgery using a donor graft remained the only option for limb salvage. Amputation of the toes on the left foot due to gangrene was necessary. Subsequently, femoro-pedal bypass to the left common plantar artery was performed using a great saphenous vein allograft. The post-operative course was without complications, the pedal bypass was patent and toe amputation was with good healing. The patient remained in follow-up care. A good outcome of vascular reconstruction with an allograft depends on the availability of a suitable allograft and good patient compliance with post-operative care. In the case presented here, the pedal bypass grafting by means of an allograft helped to save the patients limb. pedal bypass venous allograft limb salvage.

Helping working Equidae and their owners in developing countries: monitoring and evaluation of evidence-based interventions.

PubMed

Upjohn, Melissa M; Pfeiffer, Dirk U; Verheyen, Kristien L P

2014-02-01

There are an estimated 112 million Equidae (horses, donkeys, mules) in the developing world, providing essential resources for their owners' livelihoods and well-being. The impoverished situation of their owners and the often harsh conditions in which they work mean that the animals' welfare is a cause for concern. A number of equine non-governmental organisations (NGOs) operate within working equid communities providing veterinary care, education and training programmes aimed at improving equine welfare. However, there is little published information available that describes monitoring and evaluation (M&E) of such interventions using objective outcome-based indicators and where baseline data are available. The aim of this paper is to summarise the peer-reviewed reports of M&E in this sector and identify the key issues which need to be addressed in ensuring that such evaluations provide useful information on the work of these organisations. A rigorous evidence base for designing future interventions will provide an opportunity for enhancing the effectiveness of working equid NGO operations. Increased availability of M&E reports in the peer-reviewed literature will enable NGOs to learn from one another and disseminate to a wider audience information on the role of working Equidae and the issues they face. Copyright © 2013 Elsevier Ltd. All rights reserved.

Development and Validation of a Lifecycle-based Prognostics Architecture with Test Bed Validation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hines, J. Wesley; Upadhyaya, Belle; Sharp, Michael

On-line monitoring and tracking of nuclear plant system and component degradation is being investigated as a method for improving the safety, reliability, and maintainability of aging nuclear power plants. Accurate prediction of the current degradation state of system components and structures is important for accurate estimates of their remaining useful life (RUL). The correct quantification and propagation of both the measurement uncertainty and model uncertainty is necessary for quantifying the uncertainty of the RUL prediction. This research project developed and validated methods to perform RUL estimation throughout the lifecycle of plant components. Prognostic methods should seamlessly operate from beginning ofmore » component life (BOL) to end of component life (EOL). We term this "Lifecycle Prognostics." When a component is put into use, the only information available may be past failure times of similar components used in similar conditions, and the predicted failure distribution can be estimated with reliability methods such as Weibull Analysis (Type I Prognostics). As the component operates, it begins to degrade and consume its available life. This life consumption may be a function of system stresses, and the failure distribution should be updated to account for the system operational stress levels (Type II Prognostics). When degradation becomes apparent, this information can be used to again improve the RUL estimate (Type III Prognostics). This research focused on developing prognostics algorithms for the three types of prognostics, developing uncertainty quantification methods for each of the algorithms, and, most importantly, developing a framework using Bayesian methods to transition between prognostic model types and update failure distribution estimates as new information becomes available. The developed methods were then validated on a range of accelerated degradation test beds. The ultimate goal of prognostics is to provide an accurate assessment for RUL predictions, with as little uncertainty as possible. From a reliability and maintenance standpoint, there would be improved safety by avoiding all failures. Calculated risk would decrease, saving money by avoiding unnecessary maintenance. One major bottleneck for data-driven prognostics is the availability of run-to-failure degradation data. Without enough degradation data leading to failure, prognostic models can yield RUL distributions with large uncertainty or mathematically unsound predictions. To address these issues a "Lifecycle Prognostics" method was developed to create RUL distributions from Beginning of Life (BOL) to End of Life (EOL). This employs established Type I, II, and III prognostic methods, and Bayesian transitioning between each Type. Bayesian methods, as opposed to classical frequency statistics, show how an expected value, a priori, changes with new data to form a posterior distribution. For example, when you purchase a component you have a prior belief, or estimation, of how long it will operate before failing. As you operate it, you may collect information related to its condition that will allow you to update your estimated failure time. Bayesian methods are best used when limited data are available. The use of a prior also means that information is conserved when new data are available. The weightings of the prior belief and information contained in the sampled data are dependent on the variance (uncertainty) of the prior, the variance (uncertainty) of the data, and the amount of measured data (number of samples). If the variance of the prior is small compared to the uncertainty of the data, the prior will be weighed more heavily. However, as more data are collected, the data will be weighted more heavily and will eventually swamp out the prior in calculating the posterior distribution of model parameters. Fundamentally Bayesian analysis updates a prior belief with new data to get a posterior belief. The general approach to applying the Bayesian method to lifecycle prognostics consisted of identifying the prior, which is the RUL estimate and uncertainty from the previous prognostics type, and combining it with observational data related to the newer prognostics type. The resulting lifecycle prognostics algorithm uses all available information throughout the component lifecycle.« less

A framework for capturing clinical data sets from computerized sources.

PubMed

McDonald, C J; Overhage, J M; Dexter, P; Takesue, B Y; Dwyer, D M

1997-10-15

The pressure to improve health care and provide better care at a lower cost has generated the need for efficient capture of clinical data. Many data sets are now being defined to analyze health care. Historically, review and research organizations have simply determined what data they wanted to collect, developed forms, and then gathered the information through chart review without regard to what is already available institutionally in computerized databases. Today, much electronic patient information is available in operational data systems (for example, laboratory systems, pharmacy systems, and surgical scheduling systems) and is accessible by agencies and organizations through standards for messages, codes, and encrypted electronic mail. Such agencies and organizations should define the elements of their data sets in terms of standardized operational data, and data producers should fully adopt these code and message standards. The Health Plan Employer Data and Information Set and the Council of State and Territorial Epidemiologists in collaboration with the Centers for Disease Control and Prevention and the Association of State and Territorial Public Health Laboratory Directors provide examples of how this can be done.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deka, Deepjyoti; Backhaus, Scott N.; Chertkov, Michael

Traditionally power distribution networks are either not observable or only partially observable. This complicates development and implementation of new smart grid technologies, such as those related to demand response, outage detection and management, and improved load-monitoring. In this two part paper, inspired by proliferation of the metering technology, we discuss estimation problems in structurally loopy but operationally radial distribution grids from measurements, e.g. voltage data, which are either already available or can be made available with a relatively minor investment. In Part I, the objective is to learn the operational layout of the grid. Part II of this paper presentsmore » algorithms that estimate load statistics or line parameters in addition to learning the grid structure. Further, Part II discusses the problem of structure estimation for systems with incomplete measurement sets. Our newly suggested algorithms apply to a wide range of realistic scenarios. The algorithms are also computationally efficient – polynomial in time– which is proven theoretically and illustrated computationally on a number of test cases. The technique developed can be applied to detect line failures in real time as well as to understand the scope of possible adversarial attacks on the grid.« less