Reference of Temperature and Time during tempering process for non-stoichiometric FTO films

NASA Astrophysics Data System (ADS)

Yang, J. K.; Liang, B.; Zhao, M. J.; Gao, Y.; Zhang, F. C.; Zhao, H. L.

2015-10-01

In order to enhance the mechanical strength of Low-E glass, Fluorine-doped tin oxide (FTO) films have to be tempered at high temperatures together with glass substrates. The effects of tempering temperature (600 °C ~ 720 °C) and time (150 s ~ 300 s) on the structural and electrical properties of FTO films were investigated. The results show all the films consist of non-stoichiometric, polycrystalline SnO2 without detectable amounts of fluoride. 700 °C and 260 s may be the critical tempering temperature and time, respectively. FTO films tempered at 700 °C for 260 s possesses the resistivity of 7.54 × 10-4 Ω•cm, the average transmittance in 400 ~ 800 nm of ~80%, and the calculated emissivity of 0.38. Hall mobility of FTO films tempered in this proper condition is mainly limited by the ionized impurity scattering. The value of [O]/[Sn] at the film surface is much higher than the stoichiometric value of 2.0 of pure crystalline SnO2.

Electropolymerization of Uniform Polyaniline Nanorod Arrays on Conducting Oxides as Counter Electrodes in Dye-Sensitized Solar Cells.

PubMed

He, Ziming; Liu, Jing; Khoo, Si Yun; Tan, Timothy Thatt Yang

2016-01-01

Conventional techniques for the synthesis of oriented polyaniline (PANI) nanostructures are often complex or time consuming. Through an innovative reduced graphene oxide (rGO) modified FTO and a low-potential electropolymerization strategy, the rapid and template-free growth of a highly ordered PANI nanorod array on the FTO substrate is realized. The highly ordered nanostructure of the PANI array leads to a high electrocatalytic activity and chemical stability. The importance of the polymerization potential and rGO surface modification to achieve this nanostructure is revealed. Compared to platinum, the PANI nanorod array exhibits an enhanced performance and stability as counter electrodes in dye-sensitized solar cells, with a 17.6 % enhancement in power conversion efficiency. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Influence of substrates and rutile seed layers on the assembly of hydrothermally grown rutile TiO2 nanorod arrays

NASA Astrophysics Data System (ADS)

Kalb, Julian; Dorman, James A.; Folger, Alena; Gerigk, Melanie; Knittel, Vanessa; Plüisch, Claudia S.; Trepka, Bastian; Lehr, Daniela; Chua, Emily; Goodge, Berit H.; Wittemann, Alexander; Scheu, Christina; Polarz, Sebastian; Schmidt-Mende, Lukas

2018-07-01

Rutile TiO2 nanorod arrays (NRAs) are applicable in various prospective technologies. Hydrothermal methods present a simple technique to fabricate such NRAs. In this report, we present the fabrication of seed layers for the hydrothermal growth of rutile TiO2 nanorods via sputter deposition, electron-beam evaporation, and sol-gel method and study the influence of each on the growth behavior. To satisfy the requirements of numerous applications, p-type silicon, platinum, levitating carbon membranes, a template made of polystyrene spheres, and commercial fluorine tin oxide (FTO) were employed as substrates. We document the structural properties of the TiO2 seed layers and describe the relationship between the characteristics of the seed crystals, the growth evolution, and the appearance of as-grown nanorods. Various growth stages of rutile TiO2 nanorods are compared depending on whether they are grown on polycrystalline TiO2 or FTO seed layers. In both cases, a homogenous TiO2 bottom layer is formed at the seed layer/substrate interface, which is essential for electronic applications such as hybrid solar cells. Detached NRAs illustrate the effect of rutile FTO and TiO2 on the porosity of this bottom layer. Further details about the formation process of this layer are obtained from the growth on confined seed layers fabricated by electron-beam lithography.

All-nanoparticle self-assembly ZnO/TiO₂ heterojunction thin films with remarkably enhanced photoelectrochemical activity.

PubMed

Yuan, Sujun; Mu, Jiuke; Mao, Ruiyi; Li, Yaogang; Zhang, Qinghong; Wang, Hongzhi

2014-04-23

The multilaminated ZnO/TiO2 heterojunction films were successfully deposited on conductive substrates including fluorine-doped tin oxide (FTO) glass and flexible indium tin oxide coated poly(ethylene terephthalate) via the layer-by-layer (LBL) self assembly method from the oxide colloids without using any polyelectrolytes. The positively charged ZnO nanoparticles and the negatively charged TiO2 nanoparticles were directly used as the components in the consecutive deposition process to prepare the heterojunction thin films by varying the thicknesses. Moreover, the crystal growth of both oxides could be efficiently inhibited by the good connection between ZnO and TiO2 nanoparticles even after calcination at 500 °C, especially for ZnO which was able to keep the crystallite size under 25 nm. The as-prepared films were used as the working electrodes in the three-electrode photoelectrochemical cells. Because the well-contacted nanoscale heterojunctions were formed during the LBL self-assembling process, the ZnO/TiO2 all-nanoparticle films deposited on both substrates showed remarkably enhanced photoelectrochemical properties compared to that of the well-established TiO2 LBL thin films with similar thicknesses. The photocurrent response collected from the ZnO/TiO2 electrode on the FTO glass substrate was about five times higher than that collected from the TiO2 electrode. Owing to the absence of the insulating layer of dried polyelectrolytes, the ZnO/TiO2 all-nanoparticle heterojunction films were expected to be used in the photoelectrochemical device before calcination.

Dye-sensitized solar cells fabricated with black raspberry, black carrot and rosella juice

NASA Astrophysics Data System (ADS)

Tekerek, S.; Kudret, A.; Alver, Ü.

2011-10-01

In this work, dye sensitized solar cells (DSSC's) were constructed from black raspberry ( Rubus Ideaus), black carrot ( Daucuscarota L.) and rosella juice ( Hibiscus Sabdariffa L.). In order to fabricate a DSSC the fluorine-doped tin (IV) oxide (FTO) thin films obtained by using spray pyrolysis technique were used as a substrate. TiO2 films on FTO layers were prepared by doctor-blading technique. Platinum-coated counter electrode and liquid Iodide/Iodine electrolyte solution were used to fabricate DSSC's. The efficiencies of solar cells produced with black carrot, rosella and black raspberry juice were calculated as 0.25%, 0.16% and 0.16% respectively, under a sunny day in Kahramanmaraş-Turkey.

Welded-Ag-nanowires/FTO conducting film with high transmittance and its application in transparent supercapacitors

NASA Astrophysics Data System (ADS)

Qiao, Zhensong; Yang, Xiaopeng; Liu, Feng; Duan, Guangbin; Cao, Bingqiang

2017-03-01

Silver nanowires (AgNW) with a small diameter were synthesized by a facile and novel polyol reduction method. Ag nanowires ink was then spun on the surface of F-doped SnO2 (FTO) to form the AgNW/FTO conducting film. Welding treatment of the AgNW/FTO conducting film not only increased the optical transmittance from 71.9 % to 79.3 % at 550 nm and decreased the sheet resistance from 11.4 ohm sq-1 to 9.8 ohm sq-1, but also improved the adhesivity of AgNW network on FTO substrate. Furthermore, MnO2 nanosheets were directly deposited on welded-AgNW/FTO (wAF) substrate to prepare a transparent MnO2/weled-AgNW/FTO (MwAF) composite electrode. The MwAF electrode displayed excellent electrochemical performance, including high specific capacitance (375 F g-1 at 5 mV s-1) and superior cycle stability (173.3 % of the initial capacitance after 20000 GCD cycles).

Improved conversion efficiency in dye-sensitized solar cells based on electrospun Al-doped ZnO nanofiber electrodes prepared by seed layer treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yun Sining, E-mail: alexsyun1974@yahoo.com.c; Lim, Sangwoo

2011-02-15

The application of electrospun nanofibers in electronic devices is limited due to their poor adhesion to conductive substrates. To improve this, a seed layer (SD) is introduced on the FTO substrate before the deposition of the electrospun composite nanofibers. This facilitates the release of interfacial tensile stress during calcination and enhances the interfacial adhesion of the AZO nanofiber films with the FTO substrate. Dye-sensitized solar cells (DSSC) based on these AZO nanofiber photoelectrodes have been fabricated and investigated. An energy conversion efficiency ({eta}) of 0.54-0.55% has been obtained under irradiation of AM 1.5 simulated sunlight (100 mW/cm{sup 2}), indicating amore » massive improvement of {eta} in the AZO nanofiber film DSSCs after SD-treatment of the FTO substrate as compared to those with no treatment. The SD-treatment has been demonstrated to be a simple and facile method to solve the problem of poor adhesion between electrospun nanofibers and the conductive substrate. -- Graphical abstract: The poor adhesion between electrospun nanofibers and substrate is improved by a simple and facile seed layer (SD) treatment. The energy conversion efficiency of AZO nanofiber-based DSSCs has been greatly increased by SD-treatment of the FTO substrate. Display Omitted Research highlights: {yields} A simple and facile method (SD-treatment) has been demonstrated. {yields} The poor adhesion between electrospun nanofibers and substrate is improved by the SD-treatment. {yields} The {eta} of AZO nanofiber-based DSSCs has been greatly improved by SD-treatment of the FTO substrate.« less

Fundamental electrochemiluminescence characteristics of fluorine-doped tin oxides synthesized by sol-gel combustion.

PubMed

Moon, B H; Chaoumead, A; Sung, Y M

2013-10-01

Fluorine-doped tin oxide (FTO) materials synthesized by sol-gel combustion method were investigated for electrochemical luminescence (ECL) application. Effects of sol-gel combustion conditions on the structures and morphology of the porous FTO (p-FTO) materials were studied. ECL efficiency of p-FTO-based cell was about 251 cd/m2 at 4 V bias, which is higher than the sell using only FTO electrodes (102.8 cd/m2). The highest intensity of the emitting light was obtained at the wavelength of about 610 nm. The porous FTO layer was effective for increasing ECL intensities.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marimuthu, T.; Anandhan, N., E-mail: anandhan-kn@rediffmail.com; Mummoorthi, M.

Zinc oxide (ZnO) and zinc oxide/eosin yellow (ZnO/EY) thin films were potentiostatically deposited onto fluorine doped tin oxide (FTO) glass substrate. Effect of eosin yellow dye on structural, morphological and optical properties was studied. X-ray diffraction patterns, micro Raman spectra and photoluminescence (PL) spectra reveal hexagonal wurtzite structure with less atomic defects in 101 plane orientation of the ZnO/EY film. Scanning electron microscopy (SEM) images show flower for ZnO and porous like structure for ZnO/EY thin film, respectively. DSSC was constructed and evaluated by measuring the current density verses voltage curve.

Poly(3,4-ethylenedioxythiophene)/reduced graphene oxide composites as counter electrodes for high efficiency dye-sensitized solar cells

NASA Astrophysics Data System (ADS)

Ma, Jinfu; Yuan, Shenghua; Yang, Shaolin; Lu, Hui; Li, Yingtao

2018-05-01

A facile, low cost, easy-controllable method to prepare Poly(3,4-ethylenedioxythiophene) (PEDOT)/reduced graphene oxide (rGO) composites by electrochemical deposition onto fluorinated tin oxide (FTO) as counter electrodes (CEs) in high performance dye-sensitized solar cells (DSSCs) is reported. The electro-deposition process was accomplished by electro-polymerization of graphene oxide (GO)/PEDOT composites onto FTO substrates followed by electrochemical reduction of the GO component. Electrochemical measurements show that the I-/I3- catalytic activity of the as-prepared PEDOT/rGO CE is improved compared with that of the pure PEDOT and PEDOT/GO electrode. Through the analysis of photoelectric properties, the performance of the electrodes fabricated with different polymerization times are compared, and the optimal preparation condition is determined. The photoelectric conversion efficiency (PCE) of the DSSC assembled with PEDOT/rGO electrode reaches 7.79%, close to 8.33% of the cell with Platinum (Pt) electrode, and increases by 13.2% compared with 6.88% of the device with the PEDOT electrode.

Secondary electron emission characteristics of oxide electrodes in flat electron emission lamp

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chiang, Chang-Lin, E-mail: CLChiang@itri.org.tw; Li, Chia-Hung; Department of Electrophysics, National Chiao Tung University, 1001 Ta Hsueh Road, Hsinchu 300, Taiwan

2016-01-15

The present study concerns with the secondary electron emission coefficient, γ, of the cathode materials used in the newly developed flat electron emission lamp (FEEL) devices, which essentially integrates the concept of using cathode for fluorescent lamp and anode for cathode ray tube (CRT) to obtain uniform planar lighting. Three different cathode materials, namely fluorine-doped tin oxide (FTO), aluminum oxide coated FTO (Al{sub 2}O{sub 3}/FTO) and magnesium oxide coated FTO (MgO/FTO) were prepared to investigate how the variations of γ and working gases influence the performance of FEEL devices, especially in lowering the breakdown voltage and pressure of the workingmore » gases. The results indicate that the MgO/FTO bilayer cathode exhibited a relatively larger effective secondary electron emission coefficient, resulting in significant reduction of breakdown voltage to about 3kV and allowing the device to be operated at the lower pressure to generate the higher lighting efficiency.« less

Electric field induced metal-insulator transition in VO2 thin film based on FTO/VO2/FTO structure

NASA Astrophysics Data System (ADS)

Hao, Rulong; Li, Yi; Liu, Fei; Sun, Yao; Tang, Jiayin; Chen, Peizu; Jiang, Wei; Wu, Zhengyi; Xu, Tingting; Fang, Baoying

2016-03-01

A VO2 thin film has been prepared using a DC magnetron sputtering method and annealing on an F-doped SnO2 (FTO) conductive glass substrate. The FTO/VO2/FTO structure was fabricated using photolithography and a chemical etching process. The temperature dependence of the I-V hysteresis loop for the FTO/VO2/FTO structure has been analyzed. The threshold voltage decreases with increasing temperature, with a value of 9.2 V at 20 °C. The maximum transmission modulation value of the FTO/VO2/FTO structure is 31.4% under various temperatures and voltages. Optical modulation can be realized in the structure by applying an electric field.

Electrochemical preparation of vertically aligned, hollow CdSe nanotubes and their p-n junction hybrids with electrodeposited Cu2O.

PubMed

Debgupta, Joyashish; Devarapalli, Ramireddy; Rahman, Shakeelur; Shelke, Manjusha V; Pillai, Vijayamohanan K

2014-08-07

Vertically aligned, hollow nanotubes of CdSe are grown on fluorine doped tin oxide (FTO) coated glass substrates by ZnO nanowire template-assisted electrodeposition technique, followed by selective removal of the ZnO core using NH4OH. A detailed mechanism of nucleation and anisotropic growth kinetics of nanotubes have been studied by a combination of characterization tools such as chronoamperometry, SEM and TEM. Interestingly, "as grown" CdSe nanotubes (CdSe NTs) on FTO coated glass plates behave as n-type semiconductors exhibiting an excellent photo-response (with a generated photocurrent density value of ∼ 470 μA cm(-2)) while in contact with p-type Cu2O (p-type semiconductor, grown separately on FTO plates) because of the formation of a n-p heterojunction (type II). The observed photoresponse is 3 times higher than that of a similar device prepared with electrodeposited CdSe films (not nanotubes) and Cu2O on FTO. This has been attributed to the hollow 1-D nature of CdSe NTs, which provides enhanced inner and outer surface areas for better absorption of light and also assists faster transport of photogenerated charge carriers.

Facile and Rapid Growth of Nanostructured Ln-BTC Metal-Organic Framework Films by Electrophoretic Deposition for Explosives sensing in Gas and Cr 3+ Detection in Solution.

PubMed

Feng, Ji-Fei; Yang, Xue; Gao, Shui-Ying; Shi, Jianlin; Cao, Rong

2017-12-19

Until now, it has been a challenge to prepare lanthanide metal-organic framework films on traditional substrates, like zinc plate, indium oxide (ITO), and fluorine-doped tin oxide (FTO) glasses in a rapid and facile method. In this paper, continuous and dense Ln-BTC MOFs films on unmodified low-cost substrates have been rapidly and easily fabricated though the newly developed electrophoretic deposition (EPD) method in 5 min. Moreover, the as-prepared luminescent films were successfully used for the detection of nitrobenzene (NB), trinitrotoluene (TNT) in gas phases, as well as NB, Cr 3+ ions for detection in solution.

Structural, morphological and optical studies of F doped SnO2 thin films

NASA Astrophysics Data System (ADS)

Chandel, Tarun; Thakur, Vikas; Dwivedi, Shailendra Kumar; Zaman, M. Burhanuz; Rajaram, Poolla

2018-05-01

Highly conducting and transparent FTO (flourine doped tin Oxide) thin films were grown on the glass substrates using a low cost spray pyrolysis technique. The films were characterized for their structural, morphological and optical studies using XRD, SEM and UV-Vis spectroscopy. XRD studies show that the FTO films crystallize in Tetragonal cassiterite structure. Morphological analysis using SEM show that the films are uniformly covered with spherical grains albeit high in surface roughness. The average optical transmission greater than 80% in the visible region along with the appearance of interference fringes in the transmission curves confirms the high quality of the films. Electrical studies show that the films exhibit sheet resistance below 10 Ω ϒ-1.

Comparative study on deposition of fluorine-doped tin dioxide thin films by conventional and ultrasonic spray pyrolysis methods for dye-sensitized solar modules

NASA Astrophysics Data System (ADS)

Icli, Kerem Cagatay; Kocaoglu, Bahadir Can; Ozenbas, Macit

2018-01-01

Fluorine-doped tin dioxide (FTO) thin films were produced via conventional spray pyrolysis and ultrasonic spray pyrolysis (USP) methods using alcohol-based solutions. The prepared films were compared in terms of crystal structure, morphology, surface roughness, visible light transmittance, and electronic properties. Upon investigation of the grain structures and morphologies, the films prepared using ultrasonic spray method provided relatively larger grains and due to this condition, carrier mobilities of these films exhibited slightly higher values. Dye-sensitized solar cells and 10×10 cm modules were prepared using commercially available and USP-deposited FTO/glass substrates, and solar performances were compared. It is observed that there exists no remarkable efficiency difference for both cells and modules, where module efficiency of the USP-deposited FTO glass substrates is 3.06% compared to commercial substrate giving 2.85% under identical conditions. We demonstrated that USP deposition is a low cost and versatile method of depositing commercial quality FTO thin films on large substrates employed in large area dye-sensitized solar modules or other thin film technologies.

Enhanced photocatalytic activity of wool-ball-like TiO2 microspheres on carbon fabric and FTO substrates

NASA Astrophysics Data System (ADS)

Zhang, Yu; Gu, Jian; Zhang, Mengqi

2018-06-01

The wool-ball-like TiO2 microspheres on carbon fabric (TiO2-CF) and FTO substrates (TiO2-FTO) have been synthesized by a facile hydrothermal method in alkali environment, using commercial TiO2 (P25) as precursors. The XRD results indicate that the as-prepared TiO2 have good crystallinity. And the SEM images show that the wool-ball-like TiO2 microspheres with a diameter of 2-3 μm are composed of TiO2 nanowires, which have a diameter of 50 nm. The photocatalytic behavior of the wool-ball-like TiO2 microspheres, TiO2-CF and TiO2-FTO under ultraviolet light was investigated by a pseudo first-order kinetic model, using methyl orange (MO) as pollutant. The wool-ball-like TiO2 microspheres obtained a degradation rate constant (Kap) of 6.91×10-3 min-1 . The Kap values of TiO2-FTO and TiO2-CF reach 13.97×10-3 min-1 and 11.80×10-3 min-1, which are 2.0 and 1.7 times higher than that of pristine wool-ball-like TiO2 microspheres due to the "sum effect" between TiO2 and substrates. This study offers a facile hydrothermal method to prepare wool-ball-like TiO2 microspheres on CF and FTO substrates, which will improve the recyclability of phtocatalysts and can be extended to other fields.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Hongjiang; Gao, Yanfeng, E-mail: gaosic@gmail.com; School of Materials Science and Engineering, Shanghai University, Shangda Rd. 99, Baoshan, Shanghai 200444

A novel, hydrothermal and hard-template-free method was developed for the first time to grow oriented, single-crystalline monoclinic VO{sub 2} (B) flower-like nanorod films on transparent conductive fluorine-doped tin oxide (FTO) substrates. The length and morphology of the nanorods can be tuned by changing the growth parameters, such as growth time and initial precursor concentration. The flower-like V{sub 2}O{sub 5} films were obtained after post-calcination treatment of VO{sub 2} (B) films. The photocatalytic activity of V{sub 2}O{sub 5} films was investigated by the degradation of methylene blue (MB) under UV and visible light. The prepared V{sub 2}O{sub 5} film exhibited goodmore » photocatalytic performance (74.6% and 63% under UV and visible light for 210 min, respectively) and more practical application in industry. - Graphical abstract: Flower nanostructured vanadium oxide film was prepared by hydrothermal reaction for photocatalysis application. - Highlights: • Monoclinic VO{sub 2} nanorod array and flower-like nanostructure were directly grown on FTO substrate by hydrothermal reaction. • The growth mechanism was analyzed by FESEM at different time. • V{sub 2}O{sub 5} flower-like nanostructure film was obtained after calcining VO{sub 2} film. • V{sub 2}O{sub 5} film exhibited good light activity and potential application in photocatalysis.« less

A comparative study of the influence of nickel oxide layer on the FTO surface of organic light emitting diode

NASA Astrophysics Data System (ADS)

Saikia, Dhrubajyoti; Sarma, Ranjit

2018-03-01

The influence of thin layer of nickel oxide (NiO) over the fluorine-doped tin oxide (FTO) surface on the performance of Organic light-emitting diode (OLED) is reported. With an optimal thickness of NiO (10 nm), the luminance efficiency is found to be increased as compared to the single FTO OLED. The performance of OLED is studied by depositing NiO films at different thicknesses on the FTO surface and analyzed their J-V and L-V characteristics. Further analysis is carried out by measuring sheet resistance and optical transmittance. The surface morphology is studied with the help of FE-SEM images. Our results indicate that NiO (10 nm) buffer layer is an excellent choice to increase the efficiency of FTO based OLED devices within the charge tunneling region. The maximum value of current efficiency is found to be 7.32 Cd/A.

Impact of Film Thickness of Ultrathin Dip-Coated Compact TiO2 Layers on the Performance of Mesoscopic Perovskite Solar Cells.

PubMed

Masood, Muhammad Talha; Weinberger, Christian; Sarfraz, Jawad; Rosqvist, Emil; Sandén, Simon; Sandberg, Oskar J; Vivo, Paola; Hashmi, Ghufran; Lund, Peter D; Österbacka, Ronald; Smått, Jan-Henrik

2017-05-31

Uniform and pinhole-free electron-selective TiO 2 layers are of utmost importance for efficient perovskite solar cells. Here we used a scalable and low-cost dip-coating method to prepare uniform and ultrathin (5-50 nm) compact TiO 2 films on fluorine-doped tin oxide (FTO) glass substrates. The thickness of the film was tuned by changing the TiCl 4 precursor concentration. The formed TiO 2 follows the texture of the underlying FTO substrates, but at higher TiCl 4 concentrations, the surface roughness is substantially decreased. This change occurs at a film thickness close to 20-30 nm. A similar TiCl 4 concentration is needed to produce crystalline TiO 2 films. Furthermore, below this film thickness, the underlying FTO might be exposed resulting in pinholes in the compact TiO 2 layer. When integrated into mesoscopic perovskite solar cells there appears to be a similar critical compact TiO 2 layer thickness above which the devices perform more optimally. The power conversion efficiency was improved by more than 50% (from 5.5% to ∼8.6%) when inserting a compact TiO 2 layer. Devices without or with very thin compact TiO 2 layers display J-V curves with an "s-shaped" feature in the negative voltage range, which could be attributed to immobilized negative ions at the electron-extracting interface. A strong correlation between the magnitude of the s-shaped feature and the exposed FTO seen in the X-ray photoelectron spectroscopy measurements indicates that the s-shape is related to pinholes in the compact TiO 2 layer when it is too thin.

Newer approach of using alternatives to (Indium doped) metal electrodes, dyes and electrolytes in dye sensitized solar cell

NASA Astrophysics Data System (ADS)

Patni, Neha; Sharma, Pranjal; Pillai, Shibu G.

2018-04-01

This work demonstrates the PV study of dye sensitised solar cells by fabricating the (PV) cell using the ITO, FTO and AZO glass substrate. Dyes used for the fabrication were extracted from beetroot and spinach and a cocktail dye by mixing both of the dyes was also prepared. Similarly the three dufferent electrolytes used were iodide-triiodide couple, polyaniline and mixture of polyaniline and iodide couple. Mixed dye and mixed electrolyte has emerged as the highest efficient cell. The electrical characterisation shows that the highest power conversion efficiency of 1.86% was achieved by FTO substrate, followed by efficiency of 1.83% by AZO substrate and efficiency of 1.63% with ITO substrate using mixed dye and mixed electrolyte approach. This justifies that FTO and AZO shows better efficiency and hence proposed to be used as an alternative to indium free system.

Influence of solution viscosity on hydrothermally grown ZnO thin films for DSSC applications

NASA Astrophysics Data System (ADS)

Marimuthu, T.; Anandhan, N.; Thangamuthu, R.; Surya, S.

2016-10-01

Zinc oxide (ZnO) nanowire arrays (NWAs) were grown onto zinc oxide-titanium dioxide (ZnO-TiO2) seeded fluorine doped tin oxide (FTO) conductive substrate by hydrothermal technique. X-ray diffraction (XRD) patterns depict that ZnO thin films are preferentially oriented along the (002) plane with hexagonal wurtzite structure. Viscosity measurements reveal that viscosity of the solutions linearly increases as the concentrations of the polyvinyl alcohol (PVA) increase in the growth solution. Field emission scanning electron microscope (FE-SEM) images show that the NWAs are vertically grown to seeded FTO substrate with hexagonal structure, and the growth of NWAs decreases as the concentration of the PVA increases. Stylus profilometer and atomic force microscopic (AFM) studies predict that the thickness and roughness of the films decrease with increasing the PVA concentrations. The NWAs prepared at 0.1% of PVA exhibits a lower transmittance and higher absorbance than that of the other films. The band gap of the optimized films prepared at 0.0 and 0.1% of PVA is found to be 3.270 and 3.268 eV, respectively. The photo to current conversion efficiency of the DSSC based on photoanodes prepared at 0.0 and 0.1% of PVA exhibits about 0.64 and 0.82%, respectively. Electrochemical impedance spectra reveal that the DSSC based on photoanode prepared at 0.1% of PVA has the highest charge transfer recombination resistance.

Effective anodic oxidation of naproxen by platinum nanoparticles coated FTO glass.

PubMed

Chin, Ching-Ju Monica; Chen, Tsan-Yao; Lee, Menshan; Chang, Chiung-Fen; Liu, Yu-Ting; Kuo, Yu-Tsun

2014-07-30

This study investigated applications of the electrochemical anodic oxidation process with Pt-FTO and Pt/MWCNTs-FTO glasses as anodes on the treatment of one of the most important emerging contaminants, naproxen. The anodes used in this study have been synthesized using commercial FTO, MWCNTs and Pt nanoparticles (PtNP). XRD patterns of Pt nanoparticles coated on FTO and MWCNTs revealed that MWCNTs can prevent the surface of PtNPs from sintering and thus provide a greater reaction sites density to interact with naproxen, which have also been confirmed by higher degradation and mineralization efficiencies in the Pt/MWCNTs-FTO system. Results from the CV analysis showed that the Pt-FTO and Pt/MWCNTs-FTO electrodes possessed dual functions of decreasing activation energy and interactions between hydroxyl radicals to effectively degrade naproxen. The lower the solution pH value, the better the degradation efficiency. The existence of humic acid indeed inhibited the degradation ability of naproxen due to the competitions in the multiple-component system. The electrochemical degradation processes were controlled by diffusion mechanism and two major intermediates of 2-acetyl-6-methoxynaphthalene and 2-(6-Hydroxy-2-naphthyl)propanoic acid were identified. This study has successfully demonstrated new, easy, flexible and effective anodic materials which can be feasibly applied to the electrochemical oxidation of naproxen. Copyright © 2014 Elsevier B.V. All rights reserved.

Structural and Optical Properties of Core-Shell TiO2/CdS Prepared by Chemical Bath Deposition

NASA Astrophysics Data System (ADS)

Al-Jawad, Selma M. H.

2017-10-01

Titanium dioxide (TiO2) nanorod arrays (NRAs) sensitized with cadmium sulfide (CdS) nanoparticles (NPs) were deposited by chemical bath deposition (CBD). TiO2 NRAs were also obtained by using the same method on glass substrates coated with fluorine-doped tin oxide (FTO). The structure of the FTO/TiO2/CdS core-shell was characterized by x-ray diffraction (XRD), atomic force microscopy, scanning electron microscopy, ultraviolet-visible (UV-Vis) absorption spectroscopy, photoluminescence, and photoelectrocatalysis of FTO/TiO2 and FTO/TiO2/CdS. The FTO/TiO2 conformed to anatase and rutile phase structures for different pH values and also with annealing. XRD patterns of the FTO/TiO2/CdS sample exhibited two peaks corresponding to hexagonal (100) and (101) for CdS. Scanning electron micrographs showed nanorod structures for the TiO2 thin films deposited at a pH value equal 0.7. Optical results showed the CdS deposited on nanorod TiO2 exhibited increased absorption ability in the visible light, indicating an increased photocatalytic activity for TiO2/CdS core-shell nanorods in the visible light. When illuminated with a UV-Vis light source, the TiO2/CdS core-shell films displayed high responses. A composite exists between the TiO2 nanostructure and CdS NPs because the film absorbs the incident light located in both the visible and UV-Vis regions. A higher response to UV-Vis light was attained with the use of TiO2 NRAs/CdS NPs films prepared by CBD. This approach offers a technique for fabricating photoelectrodes.

Synthesis and Electrochemical Property of LiMn2O4 Porous Hollow Nanofiber as Cathode for Lithium-Ion Batteries.

PubMed

Duan, Lianfeng; Zhang, Xueyu; Yue, Kaiqiang; Wu, Yue; Zhuang, Jian; Lü, Wei

2017-12-01

The LiMn 2 O 4 hollow nanofibers with a porous structure have been synthesized by modified electrospinning techniques and subsequent thermal treatment. The precursors were electrospun directly onto the fluorine-doped tin oxide (FTO) glass. The heating rate and FTO as substrate play key roles on preparing porous hollow nanofiber. As cathode materials for lithium-ion batteries (LIBs), LiMn 2 O 4 hollow nanofibers showed the high specific capacity of 125.9 mAh/g at 0.1 C and a stable cycling performance, 105.2 mAh/g after 400 cycles. This unique structure could relieve the structure expansion effectively and provide more reaction sites as well as shorten the diffusion path for Li + for improving electrochemical performance for LIBs.

Zinc Oxide/TiO2 Bilayer Heterojunction as a Working Electrode in Quasi Solid Dye Sensitized Solar Cells

NASA Astrophysics Data System (ADS)

Aprilia, A.; Safriani, L.; Arsyad, Wa Ode S.; Syakir, N.; Susilawati, T.; Mulyana, C.; Fitrilawati; Hidayat, R.

2017-07-01

Bilayer heterojunction of aluminium doped zinc oxide (AZO) and titanium dioxide (TiO2) mesoporous has been successfully deposited on fluorine tin oxide (FTO) substrate as working electrode in dye sensitized solar cell. This layer was used as working electrode in quasi solid dye sensitized solar cell. The solar cell structure is FTO/ZnO/TiO2/PGE/Pt/FTO using polymer gel electrolyte (PGE). In polymer gel electrolyte system, hybrid copolymer based on poly-TMSPMA (3-methoxysilyl propyl methacrylate) was used as a matrix to trap ionic liquid. An addition of aluminum as atom dopant also studied to observe the physical properties changes of photoanode related to solar cell performance. AlCl3 was used as dopant material with the concentrations at 0.5 weight % and 1.0 weight% of zinc acetate dehydrate as raw material. Based on our previous result, the existence of Al dopant would decrease the surface roughness of ZnO layer, reduce the grain size of ZnO particles, transmittance at visible light increase and also change the charge carrier density. Nevertheless, the highest efficiency was achieved for undoped ZnO/TiO2 photoanode (η=0.67%). Based on current-voltage measurement data analysis (using diode model equation) the ideality factor (n) of device using undoped ZnO was smaller (n=2.96) than AZO 0.5 wt% and 1.0 wt% (n=∼4), indicate better quality of undoped ZnO/TiO2 interfaces rather than AZO/TiO2.

Growth of TiO2 nanofibers on FTO substrates and their application in dye-sensitized solar cells

NASA Astrophysics Data System (ADS)

Suryana, R.; Rahmawati, L. R.; Triyana, K.

2016-11-01

Growth of TiO2 nanofibers on fluorine-doped tin oxide (FTO) substrates have been performed using electrospinning method. Homogenous TiO2 solution as nanofibers material was prepared with titanium tetraisopropoxide (TTIP), ethanol, acetic acid and polyvinyl pyrrolidone (PVP) which was stirred for 24 h. TiO2 solution was loaded into the syringe pump. Electrospun voltage was operated under 15 kV with optimum distance between syringe tip and collector was 15 cm. FTO substrates were attached on the collector surface. Electrospinning coating time was varied at 15 min, 30 min, 45 min, and 60 min. Then TiO2 nanofibers layer was annealed at temperature of 450° C for 3 h. X-ray diffraction spectrum of TiO2 nanofibers showed major anatase peaks at 25.3°, 48.0° and 37.8° correlating crystal orientation of (101), (200), and (004), respectively while only one rutile peak at 27.5°(110). TiO2 nanofibers diameter was measured using atomic force microscopy (AFM). TiO2 nanofibers have diameter in range of 100-1000 nm. The obtained-TiO2 nanofibers were applied in dye-sensitized solar cell (DSSC) with beta-carotene as dye, carbon as catalyst, and I-/I3- redox couple as electrolyte. DSSC performance was analyzed from I-V characterization. Growth of TiO2 nanofibers at electrospinning time for 45 min has highest efficiency that is 0.016%. It is considered that TiO2 nanofibers at electrospinning time for 45 min can produce optimum thickness so that it is speculated many dyes adsorb on the nanofiber surfaces and many electrons diffuse toward the electrodes.

Ion Implantation-Modified Fluorine-Doped Tin Oxide by Zirconium with Continuously Tunable Work Function and Its Application in Perovskite Solar Cells.

PubMed

Han, Dong; Wu, Cuncun; Zhao, Yunbiao; Chen, Yi; Xiao, Lixin; Zhao, Ziqiang

2017-12-06

In recent years, perovskite solar cells have drawn a widespread attention. As an electrode material, fluorine-doped tin oxide (FTO) is widely used in various kinds of solar cells. However, the relatively low work function (WF) (∼4.6 eV) limits its application. The potential barrier between the transparent conductive oxide electrode and the hole transport layer (HTL) in inverted perovskite solar cells results in a decrease in device performance. In this paper, we propose a method to adjust WF of FTO by implanting zirconium ions into the FTO surface. The WF of FTO can be precisely and continuously tuned between 4.59 and 5.55 eV through different dopant concentration of zirconium. In the meantime, the modified FTO, which had a WF of 5.1 eV to match well the highest occupied molecular orbital energy level of poly(3,4-ethylenedioxylenethiophene):polystyrene sulfonate, was used as the HTL in inverted planar perovskite solar cells. Compared with the pristine FTO electrode-based device, the open circuit voltage increased from 0.82 to 0.91 V, and the power conversion efficiency increased from 11.6 to 14.0%.

Semi-transparent ordered TiO2 nanostructures prepared by anodization of titanium thin films deposited onto the FTO substrate

NASA Astrophysics Data System (ADS)

Szkoda, Mariusz; Lisowska-Oleksiak, Anna; Grochowska, Katarzyna; Skowroński, Łukasz; Karczewski, Jakub; Siuzdak, Katarzyna

2016-09-01

In a significant amount of cases, the highly ordered TiO2 nanotube arrays grow through anodic oxidation of a titanium metal plate immersed in electrolyte containing fluoride ions. However, for some practical applications, e.g. solar cells or electrochromic windows, the semi-transparent TiO2 formed directly on the transparent, conductive substrate is very much desired. This work shows that high-quality Ti coating could be formed at room temperature using an industrial magnetron sputtering system within 50 min. Under optimized conditions, the anodization process was performed on 2 μm titanium films deposited onto the FTO (fluorine-tin-oxide) support. Depending on the electrolyte type, highly ordered tubular or porous titania layers were obtained. The fabricated samples, after their thermal annealing, were investigated using scanning electron microscopy, Raman spectroscopy and UV-vis spectroscopy in order to investigate their morphology, crystallinity and absorbance ability. The photocurrent response curves indicate that materials are resistant to the photocorrosion process and their activity is strongly connected to optical properties. The most transparent TiO2 films were fabricated when Ti was anodized in water electrolyte, whereas the highest photocurrent densities (12 μA cm-2) were registered for titania received after Ti anodization in ethylene glycol solution. The obtained results are of significant importance in the production of thin, semi-transparent titania nanostructures on a commercial scale.

Effect of fluorine doping on highly transparent conductive spray deposited nanocrystalline tin oxide thin films

NASA Astrophysics Data System (ADS)

Moholkar, A. V.; Pawar, S. M.; Rajpure, K. Y.; Bhosale, C. H.; Kim, J. H.

2009-09-01

The undoped and fluorine doped thin films are synthesized by using cost-effective spray pyrolysis technique. The dependence of optical, structural and electrical properties of SnO 2 films, on the concentration of fluorine is reported. Optical absorption, X-ray diffraction, scanning electron microscope (SEM) and Hall effect studies have been performed on SnO 2:F (FTO) films coated on glass substrates. The film thickness varies from 800 to 1572 nm. X-ray diffraction pattern reveals the presence of cassiterite structure with (2 0 0) preferential orientation for FTO films. The crystallite size varies from 35 to 66 nm. SEM and AFM study reveals the surface of FTO to be made of nanocrystalline particles. The electrical study reveals that the films are degenerate and exhibit n-type electrical conductivity. The 20 wt% F doped film has a minimum resistivity of 3.8 × 10 -4 Ω cm, carrier density of 24.9 × 10 20 cm -3 and mobility of 6.59 cm 2 V -1 s -1. The sprayed FTO film having minimum resistance of 3.42 Ω/cm 2, highest figure of merit of 6.18 × 10 -2 Ω -1 at 550 nm and 96% IR reflectivity suggest, these films are useful as conducting layers in electrochromic and photovoltaic devices and also as the passive counter electrode.

Effect of annealing temperature on the PEC performance of electrodeposited copper oxides

NASA Astrophysics Data System (ADS)

Marathey, Priyanka; Pati, Ranjan; Mukhopadhyay, Indrajit; Ray, Abhijit

2018-05-01

In this work, we have deposited Cu2O film on fluorine doped tin oxide (FTO) substrate by electrodeposition. Pure CuO phase has been obtained by annealing the electrodeposited Cu2O film at optimized temperature (500°C) for two hours in air. Copper(I) oxide films showed good photo response with a current density of 0.54mA/cm2 at 0 V vs RHE. It is evident from UV-Visible spectroscopic analysis that the bandgap of Cu(I) and Cu(II) oxides differs from each other resulting in significant change in photo current for these two phases, observed in the PEC study. However CuO film showed better stability as compared to Cu2O film.

Mesoporous Nickel Oxide (NiO) Nanopetals for Ultrasensitive Glucose Sensing

NASA Astrophysics Data System (ADS)

Mishra, Suryakant; Yogi, Priyanka; Sagdeo, P. R.; Kumar, Rajesh

2018-01-01

Glucose sensing properties of mesoporous well-aligned, dense nickel oxide (NiO) nanostructures (NSs) in nanopetals (NPs) shape grown hydrothermally on the FTO-coated glass substrate has been demonstrated. The structural study based investigations of NiO-NPs has been carried out by X-ray diffraction (XRD), electron and atomic force microscopies, energy dispersive X-ray (EDX), and X-ray photospectroscopy (XPS). Brunauer-Emmett-Teller (BET) measurements, employed for surface analysis, suggest NiO's suitability for surface activity based glucose sensing applications. The glucose sensor, which immobilized glucose on NiO-NPs@FTO electrode, shows detection of wide range of glucose concentrations with good linearity and high sensitivity of 3.9 μA/μM/cm2 at 0.5 V operating potential. Detection limit of as low as 1 μΜ and a fast response time of less than 1 s was observed. The glucose sensor electrode possesses good anti-interference ability, stability, repeatability & reproducibility and shows inert behavior toward ascorbic acid (AA), uric acid (UA) and dopamine acid (DA) making it a perfect non-enzymatic glucose sensor.

Wide Bandgap Transparent Conducting Electrode of FTO/Ag/FTO Structure for Ultraviolet Light-Emitting Diodes.

PubMed

Yohn, Gyu-Jae; Jeong, Soae; Kang, Soo-Hyun; Kim, Si-Won; Noh, Beom-Rae; Oh, Semi; Jeong, Bong-Yong; Kim, Kyoung-Kook

2018-09-01

We investigated the effect of the Ag interlayer thickness on the structural, electrical and optical properties of FTO/Ag/FTO structures designed for use in wide bandgap transparent conducting electrodes. The top and bottom FTO layers were deposited on α-Al2O3 (0001) substrates via RF magnetron sputtering at 300 °C and Ag interlayers were deposited using an e-beam evaporator system. We optimized the figure of merit by changing the thickness of the inserted Ag interlayer from 10 nm to 14 nm, achieving a maximum value of 2.46 × 10-3 Ω-1 and a resistivity of 6.4 × 10-4 Ω · cm using an FTO (70 nm)/Ag (14 nm)/FTO (40 nm) structure. Furthermore, the average optical transmittance in the deep UV range (300 to 330 nm) was 82.8%.

A novel hierarchical Pt- and FTO-free counter electrode for dye-sensitized solar cell

PubMed Central

2014-01-01

A novel hierarchical Pt- and FTO-free counter electrode (CE) for the dye-sensitized solar cell (DSSC) was prepared by spin coating the mixture of TiO2 nanoparticles and poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) solution onto the glass substrate. Compared with traditional Pt/FTO CE, the cost of the new CE is dramatically reduced by the application of bilayer TiO2-PEDOT:PSS/PEDOT:PSS film and the glass substrate. The sheet resistance of this composite film is 35 Ω sq−1 and is low enough to be used as an electrode. The surface morphologies of TiO2-PEDOT:PSS layer and modified PEDOT:PSS layer were characterized by scanning electron microscope, which shows that the former had larger surface areas than the latter. Electrochemical impedance spectra and Tafel polarization curves prove that the catalytic activity of TiO2-PEDOT:PSS/PEDOT:PSS/glass CE is higher than that of PEDOT:PSS/FTO CE and is similar to Pt/FTO CE's. This new fabricated device with TiO2-PEDOT:PSS/PEDOT:PSS/glass CE achieves a high power conversion efficiency (PCE) of 4.67%, reaching 91.39% of DSSC with Pt/FTO CE (5.11%). PMID:24808802

Electrodeposition of gold nanoparticles on mesoporous TiO{sub 2} photoelectrode to enhance visible region photocurrent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Supriyono,; Krisnandi, Yuni Krisyuningsih; Gunlazuardi, Jarnuzi, E-mail: jarnuzi@ui.ac.id

2016-04-19

Electrodeposition of gold nanoparticles (Au NPs) on the mesoporous TiO{sub 2} photoelectrode to enchance visible region photocurrent have been investigated. Mesoporous TiO{sub 2} was prepared by a sol gel method and immobilized to the fluorine doped tin oxide (FTO) substrate by dip coating technique. Gold nanoparticles were electrodeposited on the TiO{sub 2} surface and the result FTO/TiO{sub 2}/Au was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), UV-Vis diffuse reflectance spectroscopy (DRS), and X-ray diffraction (XRD). The generated photocurrent was evaluated with an electrochemical workstation (e-DAQ/e-recorder 401) using 60 W wolfram lamp as visible lightmore » source. The photoelectrochemical evaluation indicated that the presence of gold nanoparticles on TiO{sub 2} photoelectrode shall enhance the photocurrent up to 50%.« less

Composite WO 3/TiO 2 nanostructures for high electrochromic activity

DOE PAGES

Reyes-Gil, Karla R.; Stephens, Zachary D.; Stavila, Vitalie; ...

2015-01-06

A composite material consisting of TiO 2 nanotubes (NT) with WO 3 electrodeposited on its surface has been fabricated, detached from its Ti substrate, and attached to a fluorine-doped tin oxide (FTO) film on glass for application to electrochromic (EC) reactions. Several adhesion layers were tested, finding that a paste of TiO 2 made from commercially available TiO 2 nanoparticles creates an interface for the TiO 2 NT film to attach to the FTO glass, which is conductive and does not cause solution-phase ions in an electrolyte to bind irreversibly with the material. The effect of NT length and WOmore » 3 concentration on the EC performance were studied. As a result, the composite WO 3/TiO 2 nanostructures showed higher ion storage capacity, better stability, enhanced EC contrast, and longer memory time compared with the pure WO 3 and TiO 2 materials« less

Enhanced diode characteristics of organic solar cell with silanized fluorine doped tin oxide electrode

NASA Astrophysics Data System (ADS)

Sachdeva, Sheenam; Sharma, Sameeksha; Singh, Devinder; Tripathi, S. K.

2018-05-01

To investigate the diode characteristics of organic solar cell based on the planar heterojunction of 4,4'- cyclohexylidenebis[N,N-bis(4-methylphenyl)benzenamine] (TAPC) and fullerene (C70), we report the use of silanized fluorine-doped tin oxide (FTO) anode with N1-(3-trimethoxysilylpropyl)diethyltriamine (DETA) forming monolayer. The use of silanized FTO results in the decrease of saturation current density and diode ideality factor of the device. Such silanized FTO anode is found to enhance the material quality and improve the device properties.

Pt-coated cylindrical micropatterned honeycomb Petri dishes as an efficient TCO-free counter electrode in liquid junction photovoltaic devices

NASA Astrophysics Data System (ADS)

Dao, Van-Duong; Bui, Van-Tien; Choi, Ho-Suk

2018-02-01

The Pt layer deposited on a cylindrical micro cavity patterned Petri dish, which is produced using a one-step solvent-immersion phase separation, is fabricated for the first time as an FTO-free counter electrode (CE) for dye-sensitized solar cells (DSCs). Due to the high specific active surface area of the Pt-deposited honeycomb substrate CE, the efficiency of the DSC using the developed CE substrate is enhanced by 14.5% compared with the device using a Pt-sputtered flat substrate. This design strategy has potential in fabricating highly efficient and low-cost CE materials with FTO-free substrates for DSCs.

Efficient Performance of Electrostatic Spray-Deposited TiO2 Blocking Layers in Dye-Sensitized Solar Cells after Swift Heavy Ion Beam Irradiation.

PubMed

Sudhagar, P; Asokan, K; Jung, June Hyuk; Lee, Yong-Gun; Park, Suil; Kang, Yong Soo

2011-12-01

A compact TiO2 layer (~1.1 μm) prepared by electrostatic spray deposition (ESD) and swift heavy ion beam (SHI) irradiation using oxygen ions onto a fluorinated tin oxide (FTO) conducting substrate showed enhancement of photovoltaic performance in dye-sensitized solar cells (DSSCs). The short circuit current density (Jsc = 12.2 mA cm(-2)) of DSSCs was found to increase significantly when an ESD technique was applied for fabrication of the TiO2 blocking layer, compared to a conventional spin-coated layer (Jsc = 8.9 mA cm(-2)). When SHI irradiation of oxygen ions of fluence 1 × 10(13) ions/cm(2) was carried out on the ESD TiO2, it was found that the energy conversion efficiency improved mainly due to the increase in open circuit voltage of DSSCs. This increased energy conversion efficiency seems to be associated with improved electronic energy transfer by increasing the densification of the blocking layer and improving the adhesion between the blocking layer and the FTO substrate. The adhesion results from instantaneous local melting of the TiO2 particles. An increase in the electron transport from the blocking layer may also retard the electron recombination process due to the oxidized species present in the electrolyte. These findings from novel treatments using ESD and SHI irradiation techniques may provide a new tool to improve the photovoltaic performance of DSSCs.

Efficient Performance of Electrostatic Spray-Deposited TiO2 Blocking Layers in Dye-Sensitized Solar Cells after Swift Heavy Ion Beam Irradiation

PubMed Central

2011-01-01

A compact TiO2 layer (~1.1 μm) prepared by electrostatic spray deposition (ESD) and swift heavy ion beam (SHI) irradiation using oxygen ions onto a fluorinated tin oxide (FTO) conducting substrate showed enhancement of photovoltaic performance in dye-sensitized solar cells (DSSCs). The short circuit current density (Jsc = 12.2 mA cm-2) of DSSCs was found to increase significantly when an ESD technique was applied for fabrication of the TiO2 blocking layer, compared to a conventional spin-coated layer (Jsc = 8.9 mA cm-2). When SHI irradiation of oxygen ions of fluence 1 × 1013 ions/cm2 was carried out on the ESD TiO2, it was found that the energy conversion efficiency improved mainly due to the increase in open circuit voltage of DSSCs. This increased energy conversion efficiency seems to be associated with improved electronic energy transfer by increasing the densification of the blocking layer and improving the adhesion between the blocking layer and the FTO substrate. The adhesion results from instantaneous local melting of the TiO2 particles. An increase in the electron transport from the blocking layer may also retard the electron recombination process due to the oxidized species present in the electrolyte. These findings from novel treatments using ESD and SHI irradiation techniques may provide a new tool to improve the photovoltaic performance of DSSCs. PMID:27502653

Influence of dipping cycles on physical, optical, and electrical properties of Cu 2 NiSnS 4 : Direct solution dip coating for photovoltaic applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mokurala, Krishnaiah; Mallick, Sudhanshu; Bhargava, Parag

Direct solution coating technique has emerged as a promising economically viable process for earth abundant chalcogenide absorber materials for photovoltaic applications. Here, direct ethanol based dip coating of earth abundant Cu2NiSnS4 (CNTS) films on soda lime glass (SLG), molybdenum coated glass (Mo), and fluorine doped tin oxide coated glass (FTO) substrates is investigated. The structural and morphological properties of pre-annealed and sulfurized CNTS films coated on SLG, FTO, and Mo substrates are reported. The influence of dipping cycles on composition and optoelectronic properties of pre-annealed and sulfurized CNTS films deposited on SLG substrate is presented. Energy dispersive spectroscopy (EDS) andmore » X-ray fluorescence (XRF) analysis reveal how changes in thickness and elemental composition affect morphology and optoelectronic properties. The obtained absorption coefficient, optical bandgap, resistivity and mobility of pre - annealed and sulfurized films are found to be 104 cm-1, 1.5 eV, 0.48 Ocm, 3.4 cm2/Vs and 104 cm-1, 1.29 eV, 0.14 Ocm, 11.0 cm2/Vs, respectively. These properties are well suited for photovoltaic applications and lead to the conclusion that the direct ethanol based dip coating can be an alternative economically viable process for the fabrication of earth abundant CNTS absorber layers for thin film solar cells.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoon, Yeung-Pil; Kim, Jae-Hong; Ahn, Kwang-Soon, E-mail: kstheory@ynu.ac.kr

Au was electrodeposited potentiostatically at 0.3 V for 5 min on nanoporous Pt nanoparticle-coated F-doped SnO{sub 2} (FTO/Pt) substrates. For comparison, Au-electrodeposited FTO (FTO/Au) and Au-uncoated FTO/Pt were prepared. FTO/Au showed large-sized Au clusters dispersed sparsely over FTO, which resulted in lower electrocatalytic activity than FTO/Pt. In contrast, FTO/Pt exhibited poor stability unlike FTO/Au due to poisoning by the adsorption of sulfur species. The Au-electrodeposited FTO/Pt (FTO/Pt/Au) consisted of small Au clusters deposited over the entire area of Pt due to the effective Au nucleation provided by nanoporous metallic Pt. FTO/Pt/Au exhibited enhanced electrocatalytic activity and excellent stability because the small Aumore » particles well-dispersed over the nanoporous metallic Pt network provided numerous electrochemical reaction sites, and the Pt surface was not exposed to the electrolyte. When FTO/Pt/Au was used as the counter electrode (CE) of a quantum dot-sensitized solar cell, the significantly enhanced electrocatalytic activity of the FTO/Pt/Au CE facilitated the reduction reaction of S{sub n}{sup 2− }+ 2e{sup −} (CE) → S{sub n−1}{sup 2−} + S{sup 2−} at the CE/electrolyte interface, resulting in a significantly hindered recombination reaction, S{sub n}{sup 2− }+ 2e{sup −} (TiO{sub 2} in the photoanode) → S{sub n-1}{sup 2−} + S{sup 2−}, and significantly improved overall energy conversion efficiency.« less

Enhanced photovoltaic properties in dye sensitized solar cells by surface treatment of SnO2 photoanodes

PubMed Central

Basu, Kaustubh; Benetti, Daniele; Zhao, Haiguang; Jin, Lei; Vetrone, Fiorenzo; Vomiero, Alberto; Rosei, Federico

2016-01-01

We report the fabrication and testing of dye sensitized solar cells (DSSC) based on tin oxide (SnO2) particles of average size ~20 nm. Fluorine-doped tin oxide (FTO) conducting glass substrates were treated with TiOx or TiCl4 precursor solutions to create a blocking layer before tape casting the SnO2 mesoporous anode. In addition, SnO2 photoelectrodes were treated with the same precursor solutions to deposit a TiO2 passivating layer covering the SnO2 particles. We found that the modification enhances the short circuit current, open-circuit voltage and fill factor, leading to nearly 2-fold increase in power conversion efficiency, from 1.48% without any treatment, to 2.85% achieved with TiCl4 treatment. The superior photovoltaic performance of the DSSCs assembled with modified photoanode is attributed to enhanced electron lifetime and suppression of electron recombination to the electrolyte, as confirmed by electrochemical impedance spectroscopy (EIS) carried out under dark condition. These results indicate that modification of the FTO and SnO2 anode by titania can play a major role in maximizing the photo conversion efficiency. PMID:26988622

Meclofenamic acid selectively inhibits FTO demethylation of m6A over ALKBH5

PubMed Central

Huang, Yue; Yan, Jingli; Li, Qi; Li, Jiafei; Gong, Shouzhe; Zhou, Hu; Gan, Jianhua; Jiang, Hualiang; Jia, Gui-Fang; Luo, Cheng; Yang, Cai-Guang

2015-01-01

Two human demethylases, the fat mass and obesity-associated (FTO) enzyme and ALKBH5, oxidatively demethylate abundant N6-methyladenosine (m6A) residues in mRNA. Achieving a method for selective inhibition of FTO over ALKBH5 remains a challenge, however. Here, we have identified meclofenamic acid (MA) as a highly selective inhibitor of FTO. MA is a non-steroidal, anti-inflammatory drug that mechanistic studies indicate competes with FTO binding for the m6A-containing nucleic acid. The structure of FTO/MA has revealed much about the inhibitory function of FTO. Our newfound understanding, revealed herein, of the part of the nucleotide recognition lid (NRL) in FTO, for example, has helped elucidate the principles behind the selectivity of FTO over ALKBH5. Treatment of HeLa cells with the ethyl ester form of MA (MA2) has led to elevated levels of m6A modification in mRNA. Our collective results highlight the development of functional probes of the FTO enzyme that will (i) enable future biological studies and (ii) pave the way for the rational design of potent and specific inhibitors of FTO for use in medicine. PMID:25452335

Synthesis and preliminary evaluation of 18-(18)F-fluoro-4-thia-oleate as a PET probe of fatty acid oxidation.

PubMed

DeGrado, Timothy R; Bhattacharyya, Falguni; Pandey, Mukesh K; Belanger, Anthony P; Wang, Shuyan

2010-08-01

Fatty acid oxidation (FAO) is a major energy-providing process with important implications in cardiovascular, oncologic, neurologic, and metabolic diseases. A novel 4-thia oleate analog, 18-(18)F-fluoro-4-thia-oleate ((18)F-FTO), was evaluated in relationship to the previously developed palmitate analog 16-(18)F-fluoro-4-thia-palmitate ((18)F-FTP) as an FAO probe. (18)F-FTO was synthesized from a corresponding bromoester. Biodistribution and metabolite analysis studies were performed in rats. Preliminary small-animal PET studies were performed with (18)F-FTO and (18)F-FTP in rats. A practical synthesis of (18)F-FTO was developed, providing a radiotracer of high radiochemical purity (>99%). In fasted rats, myocardial uptake of (18)F-FTO (0.70 +/- 0.30% dose kg [body mass]/g [tissue mass]) was similar to that of (18)F-FTP at 30 min after injection. At 2 h, myocardial uptake of (18)F-FTO was maintained, whereas (18)F-FTP uptake in the heart was 82% reduced. Similar to (18)F-FTP, (18)F-FTO uptake by the heart was approximately 80% reduced at 30 min by pretreatment of rats with the CPT-I inhibitor etomoxir. Folch-type extraction analyses showed 70-90% protein-bound fractions in the heart, liver, and skeletal muscle, consistent with efficient trafficking of (18)F-FTO to the mitochondrion with subsequent metabolism to protein-bound species. Preliminary small-animal PET studies showed rapid blood clearance and avid extraction of (18)F-FTO and of (18)F-FTP into the heart and liver. Images of (18)F-FTO accumulation in the rat myocardium were clearly superior to those of (18)F-FTP. (18)F-FTO is shown to be a promising metabolically trapped FAO probe that warrants further evaluation.

Increased recovery rates of phosphocreatine and inorganic phosphate after isometric contraction in oxidative muscle fibers and elevated hepatic insulin resistance in homozygous carriers of the A-allele of FTO rs9939609.

PubMed

Grunnet, Louise G; Brøns, Charlotte; Jacobsen, Stine; Nilsson, Emma; Astrup, Arne; Hansen, Torben; Pedersen, Oluf; Poulsen, Pernille; Quistorff, Bjørn; Vaag, Allan

2009-02-01

Recent studies identified the rs9939609 A-allele of the FTO (fat mass and obesity associated) gene as being associated with obesity and type 2 diabetes. We studied the role of the A-allele in the regulation of peripheral organ functions involved in the pathogenesis of obesity and type 2 diabetes. Forty-six young men underwent a hyperinsulinemic euglycemic clamp with excision of skeletal muscle biopsies, an iv glucose tolerance test, 31phosphorous magnetic resonance spectroscopy, and 24-h whole body metabolism was measured in a respiratory chamber. The FTO rs9939609 A-allele was associated with elevated fasting blood glucose and plasma insulin, hepatic insulin resistance, and shorter recovery half-times of phosphocreatine and inorganic phosphate after exercise in a primarily type I muscle. These relationships--except for fasting insulin--remained significant after correction for body fat percentage. The risk allele was not associated with fat distribution, peripheral insulin sensitivity, insulin secretion, 24-h energy expenditure, or glucose and fat oxidation. The FTO genotype did not influence the mRNA expression of FTO or a set of key nuclear or mitochondrially encoded genes in skeletal muscle during rest. Increased energy efficiency--and potentially increased mitochondrial coupling--as suggested by faster recovery rates of phosphocreatine and inorganic phosphate in oxidative muscle fibers may contribute to the increased risk of obesity and type 2 diabetes in homozygous carriers of the FTO A-risk allele. Hepatic insulin resistance may represent the key metabolic defect responsible for mild elevations of fasting blood glucose associated with the FTO phenotype.

FTO regulates the chemo-radiotherapy resistance of cervical squamous cell carcinoma (CSCC) by targeting β-catenin through mRNA demethylation.

PubMed

Zhou, Shun; Bai, Zhou-Lan; Xia, Di; Zhao, Zhi-Jun; Zhao, Ren; Wang, Yan-Yang; Zhe, Hong

2018-05-01

The role of N 6 -methyladenosine (m 6 A) demethylase fat mass and obesity-associated protein (FTO) in the regulation of chemo-radiotherapy resistance remains largely unknown. Here, we show that the mRNA level of FTO is elevated in cervical squamous cell carcinoma (CSCC) tissues when compared with respective adjacent normal tissues. FTO enhances the chemo-radiotherapy resistance both in vitro and in vivo through regulating expression of β-catenin by reducing m 6 A levels in its mRNA transcripts and in turn increases excision repair cross-complementation group 1 (ERCC1) activity. Clinically, the prognostic value of FTO for overall survival is found to be dependent on β-catenin expression in human CSCC samples. Taken together, these findings uncover a critical function for FTO and its substrate m 6 A in the regulation of chemo-radiotherapy resistance, which may bear potential clinical implications for CSCC treatment. © 2018 Wiley Periodicals, Inc.

Highly piezoelectric BaTiO3 nanorod bundle arrays using epitaxially grown TiO2 nanomaterials.

PubMed

Jang, Seon-Min; Yang, Su Chul

2018-06-08

Low-dimensional piezoelectric nanostructures such as nanoparticles, nanotubes, nanowires, nanoribbons and nanosheets have been developed for potential applications as energy harvesters, tunable sensors, functional transducers and low-power actuators. In this study, lead-free BaTiO 3 nanorod bundle arrays (NBA) with highly piezoelectric properties were successfully synthesized on fluorine-doped tin oxide (FTO) substrate via a two-step process consisting of TiO 2 epitaxial growth and BaTiO 3 conversion. Through the TiO 2 epitaxial growth on FTO substrate, (001) oriented TiO 2 nanostructures formed vertically-aligned NBA with a bundle diameter of 80 nm and an aspect ratio of six. In particular, chemical etching of the TiO 2 NBA was conducted to enlarge the surface area for effective Ba 2+ ion diffusion during the perovskite conversion process from TiO 2 to BaTiO 3 . The final structure of perovskite BaTiO 3 NBA was found to exhibit a feasible piezoelectric response of 3.56 nm with a clear phase change of 180° from the single BaTiO 3 bundle, by point piezoelectric forced microscopy (PFM) analysis. Consequently, highly piezoelectric NBA could be a promising nanostructure for various nanoscale electronic devices.

Highly piezoelectric BaTiO3 nanorod bundle arrays using epitaxially grown TiO2 nanomaterials

NASA Astrophysics Data System (ADS)

Jang, Seon-Min; Yang, Su Chul

2018-06-01

Low-dimensional piezoelectric nanostructures such as nanoparticles, nanotubes, nanowires, nanoribbons and nanosheets have been developed for potential applications as energy harvesters, tunable sensors, functional transducers and low-power actuators. In this study, lead-free BaTiO 3 nanorod bundle arrays (NBA) with highly piezoelectric properties were successfully synthesized on fluorine-doped tin oxide (FTO) substrate via a two-step process consisting of TiO2 epitaxial growth and BaTiO3 conversion. Through the TiO2 epitaxial growth on FTO substrate, (001) oriented TiO2 nanostructures formed vertically-aligned NBA with a bundle diameter of 80 nm and an aspect ratio of six. In particular, chemical etching of the TiO2 NBA was conducted to enlarge the surface area for effective Ba2+ ion diffusion during the perovskite conversion process from TiO2 to BaTiO3. The final structure of perovskite BaTiO3 NBA was found to exhibit a feasible piezoelectric response of 3.56 nm with a clear phase change of 180° from the single BaTiO3 bundle, by point piezoelectric forced microscopy (PFM) analysis. Consequently, highly piezoelectric NBA could be a promising nanostructure for various nanoscale electronic devices.

Fat mass and obesity-associated (FTO) protein interacts with CaMKII and modulates the activity of CREB signaling pathway.

PubMed

Lin, Li; Hales, Chadwick M; Garber, Kathryn; Jin, Peng

2014-06-15

Polymorphisms in the fat mass and obesity-associated (FTO) gene have been associated with obesity in humans. FTO is a nuclear protein and its physiological function remains largely unknown, but alterations in its expression in mice influence energy expenditure, food intake and, ultimately, body weight. To understand the molecular functions of FTO, we performed a yeast two-hybrid screen to identify the protein(s) that could directly interact with human FTO protein. Using multiple assays, we demonstrate that FTO interacts with three isoforms of calcium/calmodulin-dependent protein kinase II: α, β and γ, which are protein kinases that phosphorylate a broad range of substrates. This interaction is functional; overexpression of FTO delays the dephosphorylation of cAMP response element-binding protein (CREB) in human neuroblastoma (SK-N-SH) cells, which in turn leads to a dramatic increase in the expression of the CREB targets neuropeptide receptor 1 (NPY1R) and brain-derived neurotrophic factor (BDNF), which already are known to regulate food intake and energy homeostasis. Thus, our results suggest that FTO could modulate obesity by regulating the activity of the CREB signaling pathway. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Ultraviolet photodetectors based on ZnO sheets: The effect of sheet size on photoresponse properties

NASA Astrophysics Data System (ADS)

Ghasempour Ardakani, Abbas; Pazoki, Meysam; Mahdavi, Seyed Mohammad; Bahrampour, Ali Reza; Taghavinia, Nima

2012-05-01

In this work, ultraviolet photodetectors based on electrodeposited ZnO sheet thin films were fabricated on a glass substrate. Before electrodeposition, a thin buffer layer of ZnO was deposited on the glass by pulsed laser deposition method. This layer not only acted as a nucleation site for ZnO sheet growth, but also made it possible to use cheap glass substrate instead of conventional fluorine-doped tin oxide (FTO) substrate. Our results showed that photoresponse properties of the photodetectors strongly depend on the sheet sizes. The smaller sheets exhibited enhanced photosensitivity, shortened fall times and decreased gain compared to larger ones. We showed that photodetectors based on ZnO sheets have a faster response than ones based on polycrystalline films. It was also shown that even less response time could be obtained by using comb-like electrodes instead of two-electrode.

Room-temperature processed tin oxide thin film as effective hole blocking layer for planar perovskite solar cells

NASA Astrophysics Data System (ADS)

Tao, Hong; Ma, Zhibin; Yang, Guang; Wang, Haoning; Long, Hao; Zhao, Hongyang; Qin, Pingli; Fang, Guojia

2018-03-01

Tin oxide (SnO2) film with high mobility and good transmittance has been reported as a promising semiconductor material for high performance perovskite solar cells (PSCs). In this study, ultrathin SnO2 film synthesized by radio frequency magnetron sputtering (RFMS) method at room temperature was employed as hole blocking layer for planar PSCs. The room-temperature sputtered SnO2 film not only shows favourable energy band structure but also improves the surface topography of fluorine doped SnO2 (FTO) substrate and perovskite (CH3NH3PbI3) layer. Thus, this SnO2 hole blocking layer can efficiently promote electron transport and suppress carrier recombination. Furthermore, the best efficiency of 13.68% was obtained for planar PSC with SnO2 hole blocking layer prepared at room temperature. This research highlights the room-temperature preparation process of hole blocking layer in PSC and has a certain reference significance for the usage of flexible and low-cost substrates.

Improvement of Transparent Conducting Performance on Oxygen-Activated Fluorine-Doped Tin Oxide Electrodes Formed by Horizontal Ultrasonic Spray Pyrolysis Deposition.

PubMed

Koo, Bon-Ryul; Oh, Dong-Hyeun; Riu, Doh-Hyung; Ahn, Hyo-Jin

2017-12-27

In this study, highly transparent conducting fluorine-doped tin oxide (FTO) electrodes were fabricated using the horizontal ultrasonic spray pyrolysis deposition. In order to improve their transparent conducting performances, we carried out oxygen activation by adjusting the ratio of O 2 /(O 2 +N 2 ) in the carrier gas (0%, 20%, and 50%) used during the deposition process. The oxygen activation on the FTO electrodes accelerated the substitution concentration of F (F O • ) into the oxygen sites in the FTO electrode while the oxygen vacancy (V O • • ) concentration was reduced. In addition, due to growth of pyramid-shaped crystallites with (200) preferred orientations, this oxygen activation caused the formation of a uniform surface structure. As a result, compared to others, the FTO electrode prepared at 50% O 2 showed excellent electrical and optical properties (sheet resistance of ∼4.0 ± 0.14 Ω/□, optical transmittance of ∼85.3%, and figure of merit of ∼5.09 ± 0.19 × 10 -2 Ω -1 ). This led to a superb photoconversion efficiency (∼7.03 ± 0.20%) as a result of the improved short-circuit current density. The photovoltaic performance improvement can be defined by the decreased sheet resistance of FTO used as a transparent conducting electrode in dye-sensitized solar cells (DSSCs), which is due to the combined effect of the high carrier concentration by the improved F O • concentration on the FTO electrodes and the fasted Hall mobility by the formation of a uniform FTO surface structure and distortion relaxation on the FTO lattices resulting from the reduced V O • • • concentration.

Electrospinning processed nanofibrous TiO2 membranes for photovoltaic applications

NASA Astrophysics Data System (ADS)

Onozuka, Katsuhiro; Ding, Bin; Tsuge, Yosuke; Naka, Takayuki; Yamazaki, Michiyo; Sugi, Shinichiro; Ohno, Shingo; Yoshikawa, Masato; Shiratori, Seimei

2006-02-01

We have recently fabricated dye-sensitized solar cells (DSSCs) comprising nanofibrous TiO2 membranes as electrode materials. A thin TiO2 film was pre-deposited on fluorine doped tin oxide (FTO) coated conducting glass substrate by immersion in TiF4 aqueous solution to reduce the electron back-transfer from FTO to the electrolyte. The composite polyvinyl acetate (PVac)/titania nanofibrous membranes can be deposited on the pre-deposited thin TiO2 film coated FTO by electrospinning of a mixture of PVac and titanium isopropoxide in N,N-dimethylformamide (DMF). The nanofibrous TiO2 membranes were obtained by calcining the electrospun composite nanofibres of PVac/titania as the precursor. Spectral sensitization of the nanofibrous TiO2 membranes was carried out with a ruthenium (II) complex, cis-dithiocyanate-N,N'-bis(2,2'-bipyridyl-4,4'-dicarboxylic acid) ruthenium (II) dihydrate. The results indicated that the photocurrent and conversion efficiency of electrodes can be increased with the addition of the pre-deposited TiO2 film and the adhesion treatment using DMF. Additionally, the dye loading, photocurrent, and efficiency of the electrodes were gradually increased by increasing the average thickness of the nanofibrous TiO2 membranes. The efficiency of the fibrous TiO2 photoelectrode with the average membrane thickness of 3.9 µm has a maximum value of 4.14%.

Direct synthesis of vertically aligned ZnO nanowires on FTO substrates using a CVD method and the improvement of photovoltaic performance

PubMed Central

2012-01-01

In this work, we report a direct synthesis of vertically aligned ZnO nanowires on fluorine-doped tin oxide-coated substrates using the chemical vapor deposition (CVD) method. ZnO nanowires with a length of more than 30 μm were synthesized, and dye-sensitized solar cells (DSSCs) based on the as-grown nanowires were fabricated, which showed improvement of the device performance compared to those fabricated using transferred ZnO nanowires. Dependence of the cell performance on nanowire length and annealing temperature was also examined. This synthesis method provided a straightforward, one-step CVD process to grow relatively long ZnO nanowires and avoided subsequent nanowire transfer process, which simplified DSSC fabrication and improved cell performance. PMID:22673046

Stability study: Transparent conducting oxides in chemically reactive plasmas

NASA Astrophysics Data System (ADS)

Manjunatha, Krishna Nama; Paul, Shashi

2017-12-01

Effect of plasma treatment on transparent conductive oxides (TCOs) including indium-doped tin oxide (ITO), fluorine-doped tin oxide (FTO) and aluminium-doped zinc oxide (AZO) are discussed. Stability of electrical and optical properties of TCOs, when exposed to plasma species generated from gases such as hydrogen and silane, are studied extensively. ITO and FTO thin films are unstable and reduce to their counterparts such as Indium and Tin when subjected to plasma. On the other hand, AZO is not only stable but also shows superior electrical and optical properties. The stability of AZO makes it suitable for electronic applications, such as solar cells and transistors that are fabricated under plasma environment. TCOs exposed to plasma with different fabrication parameters are used in the fabrication of silicon nanowire solar cells. The performance of solar cells, which is mired by the plasma, fabricated on ITO and FTO is discussed with respect to plasma exposure parameters while showing the advantages of using chemically stable AZO as an ideal TCO for solar cells. Additionally, in-situ diagnostic tool (optical emission spectroscopy) is used to monitor the deposition process and damage caused to TCOs.

FTO gene variant modulates the neural correlates of visual food perception.

PubMed

Kühn, Anne B; Feis, Delia-Lisa; Schilbach, Leonhard; Kracht, Lutz; Hess, Martin E; Mauer, Jan; Brüning, Jens C; Tittgemeyer, Marc

2016-03-01

Variations in the fat mass and obesity associated (FTO) gene are currently the strongest known genetic factor predisposing humans to non-monogenic obesity. Recent experiments have linked these variants to a broad spectrum of behavioural alterations, including food choice and substance abuse. Yet, the underlying neurobiological mechanisms by which these genetic variations influence body weight remain elusive. Here, we explore the brain structural substrate of the obesity-predisposing rs9939609 T/A variant of the FTO gene in non-obese subjects by means of multivariate classification and use fMRI to investigate genotype-specific differences in neural food-cue reactivity by analysing correlates of a visual food perception task. Our findings demonstrate that MRI-derived measures of morphology along middle and posterior fusiform gyrus (FFG) are highly predictive for FTO at-risk allele carriers, who also show enhanced neural responses elicited by food cues in the same posterior FFG area. In brief, these findings provide first-time evidence for FTO-specific differences in both brain structure and function already in non-obese individuals, thereby contributing to a mechanistic understanding of why FTO is a predisposing factor for obesity. Copyright © 2015 Elsevier Inc. All rights reserved.

Synthesis of p-type nickel oxide nanosheets on n-type titanium dioxide nanorod arrays for p-n heterojunction-based UV photosensor

NASA Astrophysics Data System (ADS)

Yusoff, M. M.; Mamat, M. H.; Malek, M. F.; Abdullah, M. A. R.; Ismail, A. S.; Saidi, S. A.; Mohamed, R.; Suriani, A. B.; Khusaimi, Z.; Rusop, M.

2018-05-01

Titanium dioxide (TiO2) nanorod arrays (TNAs) were synthesized and deposited on fluorine tin oxide (FTO)-coated glass substrate using a novel and facile immersion method in a glass container. The synthesis and deposition of p-type nickel oxide (NiO) nanosheets (NS) on the n-type TNAs was investigated in the p-n heterojunction photodiode (PD) for the application of ultraviolet (UV) photosensor. The fabricated TNAs/NiO NS based UV photosensor exhibited a highly increased photocurrent of 4.3 µA under UV radiation (365 nm, 750 µW/cm2) at 1.0 V reverse bias. In this study, the fabricated TNAs/NiO NS p-n heterojunction based photodiode showed potential applications for UV photosensor based on the stable photo-generated current attained under UV radiation.

Enhanced photovoltaic performance of novel TiO2 photoelectrode on TCO substrates for dye-sensitized solar cells.

PubMed

Nam, Jung Eun; Kwon, Soon Jin; Jo, Hyo Jeong; Yi, Kwang Bok; Kim, Dae-Hwan; Kang, Jin-Kyu

2014-12-01

In this study, we report synthesis and growth of rutile-anatase TiO2 thin film on fluorine-doped tin oxide (FTO) glass by a two-step hydrothermal method. The effects of additional treatments (i.e., TiCl4 post-treatment and seed layer formation were also studied. Photocurrent-voltage (I-V) measurement of rutile-anatase TiO2 thin film was performed under 1.5 G light illumination. Photovoltaic performance was investigated by incident photon-to-electron conversion efficiency (IPCE), electrochemical impedance spectroscopy (EIS), intensity-modulated photocurrent/photovoltage spectroscopy (IMVS/IMPS) and open-circuit photovoltage decay (OCVD).

Fabrication of TiO2/CuO photoelectrode with enhanced solar water splitting activity

NASA Astrophysics Data System (ADS)

Atabaev, Timur Sh.; Lee, Dae Hun; Hong, Nguyen Hoa

A bilayered TiO2/CuO photoelectrode was fabricated on a fluorine-doped tin oxide FTO substrate by spin-coating and pulsed laser deposition methods. The prepared bilayered system was assessed as a photoelectrode for solar water splitting. The fabricated TiO2/CuO photoelectrode exhibited a higher photocurrent density (0.022mA/cm2 at 1.23V vs. RHE) compared to bare TiO2 photoelectrode (0.013mA/cm2 at 1.23V vs. RHE). This photocurrent density enhancement was attributed to the improved charge separation combined with the improved sunlight harvesting efficiency of a bilayered structure.

Transparent solar antenna of 28 GHz using transparent conductive oxides (TCO) thin film

NASA Astrophysics Data System (ADS)

Ali, N. I. Mohd; Misran, N.; Mansor, M. F.; Jamlos, M. F.

2017-05-01

This paper presents the analysis of 28GHz solar patch antenna using the variations of transparent conductive oxides (TCO) thin film as the radiating patch. Solar antenna is basically combining the function of antenna and solar cell into one device and helps to maximize the usage of surface area. The main problem of the existing solar antenna is the radiating patch which made of nontransparent material, such as copper, shadowing the solar cell and degrades the total solar efficiency. Hence, by using the transparent conductive oxides (TCO) thin film as the radiating patch, this problem can be tackled. The TCO thin film used is varied to ITO, FTO, AgHT-4, and AgHT-8 along with glass as substrate. The simulation of the antenna executed by using Computer Simulation Technology (CST) Microwave Studio software demonstrated at 28 GHz operating frequency for 5G band applications. The performance of the transparent antennas is compared with each other and also with the nontransparent patch antenna that using Rogers RT5880 as substrate, operating at the same resonance frequency and then, the material that gives the best performance is identified.

Nanoporous Au structures by dealloying Au/Ag thermal- or laser-dewetted bilayers on surfaces

NASA Astrophysics Data System (ADS)

Ruffino, F.; Torrisi, V.; Grillo, R.; Cacciato, G.; Zimbone, M.; Piccitto, G.; Grimaldi, M. G.

2017-03-01

Nanoporous Au attracts great technological interest and it is a promising candidate for optical and electrochemical sensors. In addition to nanoporous Au leafs and films, recently, interest was focused on nanoporous Au micro- and nano-structures on surfaces. In this work we report on the study of the characteristics of nanoporous Au structures produced on surfaces. We developed the following procedures to fabricate the nanoporous Au structures: we deposited thin Au/Ag bilayers on SiO2 or FTO (fluorine-doped tin oxide) substrates with thickness xAu and xAg of the Au and Ag layers; we induced the alloying and dewetting processes of the bilayers by furnace annealing processes of the bilayers deposited on SiO2 and by laser irradiations of the bilayers deposited on FTO; the alloying and dewetting processes result in the formation of AuxAgy alloy sub-micron particles being x and y tunable by xAu and xAg. These particles are dealloyed in HNO3 solution to remove the Ag atoms. We obtain, so, nanoporous sub-micron Au particles on the substrates. Analyzing the characteristics of these particles we find that: a) the size and shape of the particles depend on the nature of the dewetting process (solid-state dewetting on SiO2, molten-state dewetting on FTO); b) the porosity fraction of the particles depends on how the alloying process is reached: about 32% of porosity for the particles fabricated by the furnace annealing at 900 °C, about 45% of porosity for the particles fabricated by the laser irradiation at 0.5 J/cm2, in both cases independently on the Ag concentration in the alloy; c) After the dealloying process the mean volume of the Au particles shrinks of about 39%; d) After an annealing at 400 °C the nanoporous Au particles reprise their initial volume while the porosity fraction is reduced. Arguments to justify these behaviors are presented.

Hepatic FTO expression is increased in NASH and its silencing attenuates palmitic acid-induced lipotoxicity.

PubMed

Lim, Andrea; Zhou, Jin; Sinha, Rohit A; Singh, Brijesh K; Ghosh, Sujoy; Lim, Kiat-Hon; Chow, Pierce Kah-Hoe; Woon, Esther C Y; Yen, Paul M

2016-10-21

Non-alcoholic steatohepatitis (NASH) is one of the most common causes of liver failure worldwide. It is characterized by excess fat accumulation, inflammation, and increased lipotoxicity in hepatocytes. Currently, there are limited treatment options for NASH due to lack of understanding of its molecular etiology. In the present study, we demonstrate that the expression of fat mass and obesity associated gene (FTO) is significantly increased in the livers of NASH patients and in a rodent model of NASH. Furthermore, using human hepatic cells, we show that genetic silencing of FTO protects against palmitate-induced oxidative stress, mitochondrial dysfunction, ER stress, and apoptosis in vitro. Taken together, our results show that FTO may have a deleterious role in hepatic cells during lipotoxic conditions, and strongly suggest that up-regulation of FTO may contribute to the increased liver damage in NASH. Copyright © 2016 Elsevier Inc. All rights reserved.

Performance analysis and comparison of ITO- and FTO-based optically transparent terahertz U-shaped patch antennas

NASA Astrophysics Data System (ADS)

Thampy, Anand Sreekantan; Dhamodharan, Sriram Kumar

2015-02-01

An indium-doped tin oxide (ITO) and a fluorine-doped tin oxide (FTO)-based optically transparent U-shaped patch antennas are designed to resonate at 750 GHz and their performances are analyzed. Impedance bandwidth, radiation efficiency, directivity and gain of the proposed antennas are investigated. The proposed transparent antenna's characteristics are compared with the copper-based non-transparent U-shaped patch antenna, which is also designed to resonate at 750 GHz. Terahertz antennas are essential for inter-satellite communications systems to enable the adequate spatial resolution, broad bandwidth, higher data rates and highly directional beam with secured data transfer. The proposed ITO- and FTO-based transparent antennas have yielded impedance bandwidth of 9.54% and 11.49%, respectively, in the band 719-791 GHz and 714-801 GHz, respectively. The peak gain for ITO and FTO based transparent antennas is 3.35 dB and 2.26 dB at 732 GHz and 801 GHz, respectively. The proposed antennas are designed and simulated by using a finite element method based electromagnetic solver, Ansys - HFSS.

Dual roles of a flouride-doped SnO2/TiO2 bilayer based on inverse opal/nanoparticle structure for water oxidation

NASA Astrophysics Data System (ADS)

Yun, Gun; Balamurugan, Maheswari; Ahn, Kwang-Soon; Lee, Sang-Kwon; Kang, Soon Hyung; Lim, Dong-Ha

2018-01-01

Fluorine-doped tin dioxide (FTO) inverse opals (IOs) were fabricated on a template of polystyrene (PS) beads (diameter = 400 nm (±20 nm)) by using a spin-coating method. The concentration of the FTO precursor, in particular, the 1.0 M FTO concentration solution significantly influenced the morphology of the IO film. The FTO nanoparticles upon the FTO IO film were sparsely formed relative to these formed from the 0.5 M FTO solution. To compensate for the large band gap ( E g = 3.8 eV) of FTO in the photoelectrochemical (PEC) reaction, we deposited a photoactive TiO2 shell on the FTO IO film by using the sol-gel method. The morphological change and the crystalline properties of the FTO IO and TiO2-coated FTO IO (hereafter referred to as FTO IO/TiO2) films, were investigated with field emission scanning electron microscopy and X-ray diffraction, respectively. The PEC behaviors of the samples were tested in a 0.1 M KOH solution under one sun illumination (100 mW/cm2 with an AM 1.5 filter). The highest PEC performance was obtained with the 1.0 M FTO IO/TiO2 film, which produced a photocurrent density (Jsc) of 3.28 mA/cm2 at 1.23 V (vs. normal hydrogen electrode (NHE), as briefly expressed to 1.23 VNHE) compared to 2.42 mA/cm2 at 1.23 VNHE with the 0.5 M FTO IO/TiO2 film. The approximately 30% enhanced performance of the 1.0 M FTO IO/TiO2 film was mainly attributed to the peculiar structure comprised of the FTO nanoparticle layer and IO films to form a bilayer structure, providing a much larger surface area, as well as complete coverage of the photoactive TiO2 nanoparticles through the FTO IO skeleton in the proper band alignment to boost the charge separation/transfer phenomenon, finally resulting in the enhanced PEC activity.

FTO associations with obesity and telomere length.

PubMed

Zhou, Yuling; Hambly, Brett D; McLachlan, Craig S

2017-09-01

This review examines the biology of the Fat mass- and obesity-associated gene (FTO), and the implications of genetic association of FTO SNPs with obesity and genetic aging. Notably, we focus on the role of FTO in the regulation of methylation status as possible regulators of weight gain and genetic aging. We present a theoretical review of the FTO gene with a particular emphasis on associations with UCP2, AMPK, RBL2, IRX3, CUX1, mTORC1 and hormones involved in hunger regulation. These associations are important for dietary behavior regulation and cellular nutrient sensing via amino acids. We suggest that these pathways may also influence telomere regulation. Telomere length (TL) attrition may be influenced by obesity-related inflammation and oxidative stress, and FTO gene-involved pathways. There is additional emerging evidence to suggest that telomere length and obesity are bi-directionally associated. However, the role of obesity risk-related genotypes and associations with TL are not well understood. The FTO gene may influence pathways implicated in regulation of TL, which could help to explain some of the non-consistent relationship between weight phenotype and telomere length that is observed in population studies investigating obesity.

Continuous Microreactor-Assisted Solution Deposition for Scalable Production of CdS Films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramprasad, Sudhir; Su, Yu-Wei; Chang, Chih-Hung

2013-06-13

Solution deposition offers an attractive, low temperature option in the cost effective production of thin film solar cells. Continuous microreactor-assisted solution deposition (MASD) was used to produce nanocrystalline cadmium sulfide (CdS) films on fluorine doped tin oxide (FTO) coated glass substrates with excellent uniformity. We report a novel liquid coating technique using a ceramic rod to efficiently and uniformly apply reactive solution to large substrates (152 mm × 152 mm). This technique represents an inexpensive approach to utilize the MASD on the substrate for uniform growth of CdS films. Nano-crystalline CdS films have been produced from liquid phase at ~90°C,more » with average thicknesses of 70 nm to 230 nm and with a 5 to 12% thickness variation. The CdS films produced were characterized by UV-Vis spectroscopy, transmission electron microscopy, and X-Ray diffraction to demonstrate their suitability to thin-film solar technology.« less

Enhanced photovoltaic performance of inverted hybrid bulk-heterojunction solar cells using TiO2/reduced graphene oxide films as electron transport layers

NASA Astrophysics Data System (ADS)

Morais, Andreia; Alves, João Paulo C.; Lima, Francisco Anderson S.; Lira-Cantu, Monica; Nogueira, Ana Flavia

2015-01-01

In this study, we investigated inverted hybrid bulk-heterojunction solar cells with the following configuration: fluorine-doped tin oxide (FTO) |TiO2/RGO|P3HT:PC61BM|V2O5 or PEDOT:PSS|Ag. The TiO2/GO dispersions were prepared by sol-gel method, employing titanium isopropoxide and graphene oxide (GO) as starting materials. The GO concentration was varied from 0.1 to 4.0 wt%. The corresponding dispersions were spin-coated onto FTO substrates and a thermal treatment was performed to remove organic materials and to reduce GO to reduced graphene oxide (RGO). The TiO2/RGO films were characterized by x-ray diffraction, Raman spectroscopy, and microscopy techniques. Atomic force microscopy (AFM) images showed that the addition of RGO significantly changes the morphology of the TiO2 films, with loss of uniformity and increase in surface roughness. Independent of the use of V2O5 or PEDOT: PSS films as the hole transport layer, the incorporation of 2.0 wt% of RGO into TiO2 films was the optimal concentration for the best organic photovoltaic performance. The solar cells based on TiO2/RGO (2.0 wt%) electrode exhibited a ˜22.3% and ˜28.9% short circuit current density (Jsc) and a power conversion efficiency enhancement, respectively, if compared with the devices based on pure TiO2 films. Kelvin probe force microscopy images suggest that the incorporation of RGO into TiO2 films can promote the appearance of regions with different charge dissipation capacities.

A simple and transparent well-aligned ZnO nanowire array ultraviolet photodetector with high responsivity

NASA Astrophysics Data System (ADS)

Yin, Lei; Ding, Hesheng; Yuan, Zhaolin; Huang, Wendeng; Shuai, Chunjiang; Xiong, Zhaoxin; Deng, Jianping; Lv, Tengbo

2018-06-01

Well-aligned zinc oxide (ZnO) nanowire arrays were grown on an interdigital patterned fluorine tin oxide (FTO)-coated glass substrate by a facile chemical bath deposition at low temperature. Morphology, crystalline structure, and optical properties of the ZnO nanowire arrays were analyzed in detail. The results revealed that the ZnO nanowires had wurtzite structure, typically ∼40-60 nm in diameter, and ∼700-800 nm in length, a great number of highly uniform and dense nanowires grew vertically on the substrate to form the well-aligned ZnO nanowire arrays, which had very high optical transmission (>86%) in the visible light region. In addition, the performance of ZnO nanowire arrays ultraviolet (UV) photodetector was systematically examined. The photosensitivity (S), responsivity (R), response and decay time of the photodetector were 703 at +0.2 V, 113 A/W at +5 V, 23 s and 73 s respectively. Also, the photoresponse mechanism of the UV photodetector was illuminated in terms of the oxygen adsorption-photodesorption process.

Ru-bis(pyridine)pyrazolate (bpp)-Based Water-Oxidation Catalysts Anchored on TiO2: The Importance of the Nature and Position of the Anchoring Group.

PubMed

Francàs, Laia; Richmond, Craig; Garrido-Barros, Pablo; Planas, Nora; Roeser, Stephan; Benet-Buchholz, Jordi; Escriche, Lluís; Sala, Xavier; Llobet, Antoni

2016-04-04

Three distinct functionalisation strategies have been applied to the in,in-[{Ru(II)(trpy)}2(μ-bpp)(H2O)2](3+) (trpy=2,2':6',2''-terpyridine, bpp=bis(pyridine)pyrazolate) water-oxidation catalyst framework to form new derivatives that can adsorb onto titania substrates. Modifications included the addition of sulfonate, carboxylate, and phosphonate anchoring groups to the terpyridine and bis(pyridyl)pyrazolate ligands. The complexes were characterised in solution by using 1D NMR, 2D NMR, and UV/Vis spectroscopic analysis and electrochemical techniques. The complexes were then anchored on TiO2-coated fluorinated tin oxide (FTO) films, and the reactivity of these new materials as water-oxidation catalysts was tested electrochemically through controlled-potential electrolysis (CPE) with oxygen evolution detected by headspace analysis with a Clark electrode. The results obtained highlight the importance of the catalyst orientation with respect to the titania surface in regard to its capacity to catalytically oxidize water to dioxygen. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The performance of hematite nanostructures in different humidity levels

NASA Astrophysics Data System (ADS)

Ahmad, W. R. W.; Mamat, M. H.; Zoolfakar, A. S.; Khusaimi, Z.; Yusof, M. M.; Ismail, A. S.; Saidi, S. A.; Rusop, M.

2018-05-01

In this study, hematite (α-Fe2O3) nanostructure were prepared in Schott vials on fluorine-doped tin oxide (FTO) coated glass substrate using the sonicated immersion method in aqueous solution with ferric chloride FeCl3ṡ6H2O as a precursor and urea NH2-CONH2 as a stabilizer. The samples were characterized for different level of humidity conditions within range 40% to 90% RH. Based on the results obtained, the hematite nanostructure exhibited good optical properties and virtuous sensor response with high sensitivity. The fabricated hematite nanostructure has revealed a good potential for humidity sensor application based on the results obtained under different levels of humidity.

Pt-Free Counter Electrodes with Carbon Black and 3D Network Epoxy Polymer Composites

NASA Astrophysics Data System (ADS)

Kang, Gyeongho; Choi, Jongmin; Park, Taiho

2016-03-01

Carbon black (CB) and a 3D network epoxy polymer composite, representing dual functions for conductive corrosion protective layer (CCPL) and catalytic layer (CL) by the control of CB weight ratio against polymer is developed. Our strategy provides a proper approach which applies high catalytic ability and chemical stability of CB in corrosive triiodide/iodide (I3-/I-) redox electrolyte system. The CB and a 3D network epoxy polymer composite coated on the stainless steel (SS) electrode to alternate counter electrodes in dye sensitized solar cells (DSSCs). A two-step spray pyrolysis process is used to apply a solution containing epoxy monomers and a polyfunctional amine hardener with 6 wt% CB to a SS substrate, which forms a CCPL. Subsequently, an 86 wt% CB is applied to form a CL. The excellent catalytic properties and corrosion protective properties of the CB and 3D network epoxy polymer composites produce efficient counter electrodes that can replace fluorine-doped tin oxide (FTO) with CCPL/SS and Pt/FTO with CL/CCPL/SS in DSSCs. This approach provides a promising approach to the development of efficient, stable, and cheap solar cells, paving the way for large-scale commercialization.

Improved performance of organic light-emitting diode with vanadium pentoxide layer on the FTO surface

NASA Astrophysics Data System (ADS)

Saikia, D.; Sarma, R.

2017-06-01

Vanadium pentoxide layer deposited on the fluorine-doped tin oxide (FTO) anode by vacuum deposition has been investigated in organic light-emitting diode (OLED). With 12 nm optimal thickness of V2O5, the luminance efficiency is increased by 1.66 times compared to the single FTO-based OLED. The improvement of current efficiency implies that there is a better charge injection and better controlling of hole current. To investigate the performance of OLED by the buffer layer, V2O5 films of different thicknesses were deposited on the FTO anode and their J- V and L- V characteristics were studied. Further analysis was carried out by measuring sheet resistance, optical transmittance and surface morphology with the FE-SEM images. This result indicates that the V2O5 (12 nm) buffer layer is a good choice for increasing the efficiency of FTO-based OLED devices within the tunnelling region. Here the maximum value of current efficiency is found to be 2.83 cd / A.

Enhanced photoelectrochemical performance of inorganic-organic hybrid consisting of BiVO4 and PEDOT:PSS

NASA Astrophysics Data System (ADS)

Trzciński, K.; Szkoda, M.; Siuzdak, K.; Sawczak, M.; Lisowska-Oleksiak, A.

2016-12-01

The PEDOT:PSS (poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)) was electrodeposited on a thin layer of bismuth vanadate (BiVO4) prepared using the pulsed laser deposition technique onto FTO. The inorganic-organic junction was characterized by Raman spectroscopy, UV-vis spectroscopy and scanning electron microscopy. Chronoamperometry curves, recorded under simulated solar light illumination, were performed to determine generated photocurrent during water and hydroquinone oxidation at the electrode surface. Experiments were performed for three types of electrode materials: (i) FTO/BiVO4, (ii) FTO/PEDOT:PSS and (iii) FTO/BiVO4/PEDOT:PSS in aqueous electrolyte. Almost 5 times higher photocurrent in electrolyte containing hole scavenger was generated after modification of BiVO4 photoanode with electrodeposited polymer. It is noteworthy that anodic photocurrent was stable even after 4 h of illumination. Cyclic voltammetry curves of FTO/BiVO4/PEDOT:PSS recorded before and after experiments performed under electrode illumination indicated that the organic part in tested junction is photo-corrosion resistant.

Electrical, optical and structural properties of FTO thin films fabricated by spray ultrasonic nebulizer technique from SnCl4 precursor

NASA Astrophysics Data System (ADS)

Lalasari, Latifa Hanum; Arini, Tri; Andriyah, Lia; Firdiyono, F.; Yuwono, Akhmad Herman

2018-05-01

Thin films of fluorine-doped tin oxide on glass were prepared by spray ultrasonic nebulizer technique from an economic anhydrous tin (IV) chloride (SnCl4) precursor. The effect of deposition time on the structural, electrical and optical properties of tin oxide thin films was investigated. This research a purpose to find an optimum deposition time during spray pyrolysis technique in order to produce FTO with the desired characteristics. For this purpose, soda lime glasses are heated at 350 °C on deposition time of 10, 15, 20 and 25 minutes. NH4F was doped at a ratio of 2 wt% in the SnCl4 precursor and methanol solvent. The results revealed that longer deposition times created decreased the electrical resistivity and optical transmittance of FTO layers. The highest optical transmittance was 84.808% and the lowest resistivity was 4.01×10-5 Ω.cm, obtained from FTO glass subjected to a 15-minute deposition time at deposition temperature of 350 °C. This is accordance to the TCO conductive glass requirements for the minimum resistivity value on scale 10-4 Ω.cm and optical transmittance value of 80-85%.

Fabrication of Polymeric Antireflection Film Manufactured by Anodic Aluminum Oxide Template on Dye-Sensitized Solar Cells.

PubMed

Tsai, Jenn-Kai; Tu, Yu-Shin

2017-03-15

In this study, high energy conversion efficient dye-sensitized solar cells (DSSCs) were successfully fabricated by attaching a double anti-reflection (AR) layer, which is composed of a subwavelength moth-eye structured polymethyl methacrylate (PMMA) film and a polydimethylsiloxane (PDMS) film. An efficiency of up to 6.79% was achieved. The moth-eye structured PMMA film was fabricated by using an anodic aluminum oxide (AAO) template which is simple, low-cost and scalable. The nano-pattern of the AAO template was precisely reproduced onto the PMMA film. The photoanode was composed of Titanium dioxide (TiO₂) nanoparticles (NPs) with a diameter of 25 nm deposited on the fluorine-doped tin oxide (FTO) glass substrate and the sensitizer N3. The double AR layer was proved to effectively improve the short-circuit current density (JSC) and conversion efficiency from 14.77 to 15.79 mA/cm² and from 6.26% to 6.79%, respectively.

Effect of polyvinyl alcohol on electrochemically deposited ZnO thin films for DSSC applications

NASA Astrophysics Data System (ADS)

Marimuthu, T.; Anandhan, N.

2017-05-01

Nanostructures of zinc oxide (ZnO) thin film are electrochemically deposited in the absence and presence of polyvinyl alcohol (PVA) on fluorine doped tin oxide (FTO) substrate. X-ray diffraction (XRD) patterns and Raman spectroscopy confirmed the formation of hexagonal structure of ZnO. The film prepared in the presence of PVA showed a better crystallinity and its crystalline growth along the (002) plane orientation. Field emission scanning electron microscope (FE-SEM) images display nanowire arrays (NWAs) and sponge like morphology for films prepared in the absence and presence of PVA, respectively. Photoluminescence (PL) spectra depict the film prepared in the presence PVA having less atomic defects with good crystal quality compared with other film. Dye sensitized solar cell (DSSC) is constructed using low cost eosin yellow dye and current-voltage (J-V) curve is recorded for optimized sponge like morphology based solar cell.

Surface modification effects of fluorine-doped tin dioxide by oxygen plasma ion implantation

NASA Astrophysics Data System (ADS)

Tang, Peng; Liu, Cai; Zhang, Jingquan; Wu, Lili; Li, Wei; Feng, Lianghuan; Zeng, Guanggen; Wang, Wenwu

2018-04-01

SnO2:F (FTO), as a kind of transparent conductive oxide (TCO), exhibits excellent transmittance and conductivity and is widely used as transparency electrodes in solar cells. It's very important to modifying the surface of FTO for it plays a critical role in CdTe solar cells. In this study, modifying effects of oxygen plasma on FTO was investigated systematically. Oxygen plasma treatment on FTO surface with ion accelerating voltage ranged from 0.4 kV to 1.6 kV has been processed. The O proportion of surface was increased after ion implantation. The Fermi level of surface measurement by XPS valance band spectra was lowered as the ion accelerating voltage increased to 1.2 kV and then raised as accelerating voltage was elevated to 1.6 kV. The work function measured by Kelvin probe force microscopy increased after ion implanting, and it was consistent with the variation of Fermi level. The change of energy band structure of FTO surface mainly originated from the surface composition variation. As FTO conduction was primarily due to oxyanion hole, the carrier was electron and its concentration was reduced while O proportion was elevated at the surface of FTO, as a result, the Fermi level lowered and the work function was enlarged. It was proved that oxygen plasma treatment is an effective method to modulate the energy band structure of the surface as well as other properties of FTO, which provides much more space for interface and surface modification and then photoelectric device performance promotion.

The optical properties of α-Fe2O3 nanostructures synthesized with different immersion time

NASA Astrophysics Data System (ADS)

Ahmad, W. R. W.; Mamat, M. H.; Zoolfakar, A. S.; Khusaimi, Z.; Yusof, M. M.; Ismail, A. S.; Saidi, S. A.; Rusop, M.

2018-05-01

In this study, nanostructured hematite (α-Fe2O3) thin films have been prepared successfully by sonicated immersion method on fluorine-doped tin oxide (FTO) coated glass substrate. The effect of the immersion time on the structural and optical properties of α-Fe2O3 nanostructure were investigated for a variation of immersion time ranging from 1 to 4 hour. From the characterization results, the surface morphology of the sample prepared in 4 hours immersion process has exhibited highest porosity, and the highest absorbance properties were found in the same sample. These results suggest that the different time duration during immersion process play important roles in optical properties of α-Fe2O3 nanostructures.

An all-solid-state perovskite-sensitized solar cell based on the dual function polyaniline as the sensitizer and p-type hole-transporting material

NASA Astrophysics Data System (ADS)

Xiao, Yaoming; Han, Gaoyi; Chang, Yunzhen; Zhou, Haihan; Li, Miaoyu; Li, Yanping

2014-12-01

High performance dual function of polyaniline (PANI) with brachyplast structure is synthesized by using a two-step cyclic voltammetry (CV) approach onto the fluorinated tin oxide (FTO) glass substrate, which acts as the sensitizer and p-type hole-transporting material (p-HTM) for the all-solid-state perovskite-sensitized solar cell (ass-PSSC) due to its π-π* transition and the localized polaron. The ass-PSSC based on the PANI delivers a photovoltaic conversion efficiency of 7.34%, and reduces from 7.34% to 6.71% after 1000 h, thereby 91.42% of the energy conversion efficiency is kept, indicating the device has a good long-term stability.

Aerosol-assisted chemical vapor deposition of ultra-thin CuOx films as hole transport material for planar perovskite solar cells

NASA Astrophysics Data System (ADS)

Zhang, Zhixin; Chen, Shuqun; Li, Pingping; Li, Hongyi; Wu, Junshu; Hu, Peng; Wang, Jinshu

This paper reports on the fabrication of CuOx films to be used as hole transporting layer (HTL) in CH3NH3PbI3 perovskite solar cells (PSCs). Ultra-thin CuOx coatings were grown onto FTO substrates for the first time via aerosol-assisted chemical vapor deposition (AACVD) of copper acetylacetonate in methanol. After incorporating into the PSCs prepared at ambient air, a highest power conversion efficiency (PCE) of 8.26% with HTL and of 3.34% without HTL were achieved. Our work represents an important step in the development of low-cost CVD technique for fabricating ultra-thin metal oxide functional layers in thin film photovoltaics.

Plasmonic-enhanced graphene flake counter electrodes for dye-sensitized solar cells

NASA Astrophysics Data System (ADS)

Kim, Hyun-Young; Lee, Myung Woo; Song, Da Hyun; Yoon, Hyeok Jin; Suh, Jung Sang

2017-06-01

A plasmonic-enhanced graphene flake counter electrode for dye-sensitized solar cells (DSSCs) was fabricated by immobilization of gold nanoparticles (NPs) on fluorine-doped tin oxide (FTO) glass and the deposition of a thin layer of graphene flakes. The graphene flakes, fabricated using a thermal plasma jet system, were very thin and pure and had good crystallinity. Even though their average size is larger than 100 nm, they had great dispersibility in common solvents. Their relatively large size and good crystallinity resulted in good conductivity, and their good dispersibility allowed us to fabricate relatively uniform films. The efficiency of the DSSC with a graphene flake/Au NP/FTO counter electrode was as much as 9.78%, which is higher than that with a conventional Pt/FTO (9.08%) or graphene flake/FTO (8.98%) counter electrode. Using cyclic voltammograms and electrochemical impedance spectroscopy and by measuring the incident photo-conversion efficiency, we proved that by the localized surface plasmon resonance effect of the Au NPs included between the graphene flakes and FTO, the charge-transfer resistance at the electrode/electrolyte interface was decreased. Consequently, the catalytic rate for I- regeneration improved, and the energy conversion efficiency of the DSSC with a graphene flake/Au NP/FTO counter electrode improved.

Assembling tungsten oxide hydrate nanocrystal colloids formed by laser ablation in liquid into fast-response electrochromic films.

PubMed

Wang, Shalong; Dou, Kang; Zou, Yousheng; Dong, Yuhang; Li, Jubin; Ju, Dan; Zeng, Haibo

2017-03-01

High-performance electrochromic films based on tungsten oxide hydrate ([WO 2 (O 2 )H 2 O]·1.66H 2 O) colloidal nanocrystals with fast switching speed were fabricated by laser ablation in a mixture of water and hydrogen peroxide followed by electrophoretic methods. Through electrophoretic deposition, the nanoparticles in the colloids synthesized by laser ablation aggregated onto the FTO coated glass substrate forming a lager cell with a uniform size of around 200nm, which subsequently self-assembled into a porous tungsten oxide hydrate film. By optimizing the electrophoretic time (800s) and voltage (-0.5V), the mesh-like porous tungsten oxide hydrate film achieved a wide optical modulation of 32% at 632nm, fast coloration and bleaching response speed of 7.8 s and 1.7s respectively due to the synergetic effect of the unique atomic structure of [WO 2 (O 2 )H 2 O]·1.66H 2 O and porous structure with large surface area that facilitates the ion insertion/extraction. Thus the tungsten oxide hydrate can be a promising electrochromic material for practical applications. Copyright © 2016 Elsevier Inc. All rights reserved.

Disposable urea biosensor based on nanoporous ZnO film fabricated from omissible polymeric substrate.

PubMed

Rahmanian, Reza; Mozaffari, Sayed Ahmad; Abedi, Mohammad

2015-12-01

In the present study, a facile and simple fabrication method of a semiconductor based urea biosensor was reported via three steps: (i) producing a ZnO-PVA composite film by means of a polymer assisted electrodeposition of zinc oxide (ZnO) on the F-doped SnO2 conducting glass (FTO) using water soluble polyvinyl alcohol (PVA), (ii) obtaining a nanoporous ZnO film by PVA omission via a subsequent post-treatment by annealing of the ZnO-PVA film, and (iii) preparation of a FTO/ZnO/Urs biosensor by exploiting a nanoporous ZnO film as an efficient and excellent platform area for electrostatic immobilization of urease enzyme (Urs) which was forced by the difference in their isoelectric point (IEP). The characterization techniques focused on the analysis of the ZnO-PVA film surfaces before and after annealing, which had a prominent effect on the porosity of the prepared ZnO film. The surface characterization of the nanostructured ZnO film by a field emission-scanning electron microscopy (FE-SEM), exhibited a film surface area as an effective bio-sensing matrix for enzyme immobilization. The structural characterization and monitoring of the biosensor fabrication was performed using UV-Vis, Fourier Transform Infrared (FT-IR), Raman Spectroscopy, Thermogravimetric Analysis (TGA), Cyclic Voltammetry (CV), and Electrochemical Impedance Spectroscopy (EIS) techniques. The impedimetric results of the FTO/ZnO/Urs biosensor showed a high sensitivity for urea detection within 8.0-110.0mg dL(-1) with the limit of detection as 5.0mg dL(-1). Copyright © 2015 Elsevier B.V. All rights reserved.

Well-Defined Nanostructured, Single-Crystalline TiO2 Electron Transport Layer for Efficient Planar Perovskite Solar Cells.

PubMed

Choi, Jongmin; Song, Seulki; Hörantner, Maximilian T; Snaith, Henry J; Park, Taiho

2016-06-28

An electron transporting layer (ETL) plays an important role in extracting electrons from a perovskite layer and blocking recombination between electrons in the fluorine-doped tin oxide (FTO) and holes in the perovskite layers, especially in planar perovskite solar cells. Dense TiO2 ETLs prepared by a solution-processed spin-coating method (S-TiO2) are mainly used in devices due to their ease of fabrication. Herein, we found that fatal morphological defects at the S-TiO2 interface due to a rough FTO surface, including an irregular film thickness, discontinuous areas, and poor physical contact between the S-TiO2 and the FTO layers, were inevitable and lowered the charge transport properties through the planar perovskite solar cells. The effects of the morphological defects were mitigated in this work using a TiO2 ETL produced from sputtering and anodization. This method produced a well-defined nanostructured TiO2 ETL with an excellent transmittance, single-crystalline properties, a uniform film thickness, a large effective area, and defect-free physical contact with a rough substrate that provided outstanding electron extraction and hole blocking in a planar perovskite solar cell. In planar perovskite devices, anodized TiO2 ETL (A-TiO2) increased the power conversion efficiency by 22% (from 12.5 to 15.2%), and the stabilized maximum power output efficiency increased by 44% (from 8.9 to 12.8%) compared with S-TiO2. This work highlights the importance of the ETL geometry for maximizing device performance and provides insights into achieving ideal ETL morphologies that remedy the drawbacks observed in conventional spin-coated ETLs.

An artificial photosynthesis anode electrode composed of a nanoparticulate photocatalyst film in a visible light responsive GaN-ZnO solid solution system

NASA Astrophysics Data System (ADS)

Imanaka, Yoshihiko; Anazawa, Toshihisa; Manabe, Toshio; Amada, Hideyuki; Ido, Sachio; Kumasaka, Fumiaki; Awaji, Naoki; Sánchez-Santolino, Gabriel; Ishikawa, Ryo; Ikuhara, Yuichi

2016-10-01

The artificial photosynthesis technology known as the Honda-Fujishima effect, which produces oxygen and hydrogen or organic energy from sunlight, water, and carbon dioxide, is an effective energy and environmental technology. The key component for the higher efficiency of this reaction system is the anode electrode, generally composed of a photocatalyst formed on a glass substrate from electrically conductive fluorine-doped tin oxide (FTO). To obtain a highly efficient electrode, a dense film composed of a nanoparticulate visible light responsive photocatalyst that usually has a complicated multi-element composition needs to be deposited and adhered onto the FTO. In this study, we discovered a method for controlling the electronic structure of a film by controlling the aerosol-type nanoparticle deposition (NPD) condition and thereby forming films of materials with a band gap smaller than that of the prepared raw material powder, and we succeeded in extracting a higher current from the anode electrode. As a result, we confirmed that a current approximately 100 times larger than those produced by conventional processes could be obtained using the same material. This effect can be expected not only from the materials discussed (GaN-ZnO) in this paper but also from any photocatalyst, particularly materials of solid solution compositions.

One-stage pulsed laser deposition of conductive zinc oxysulfide layers

NASA Astrophysics Data System (ADS)

Bereznev, Sergei; Kocharyan, Hrachya; Maticiuc, Natalia; Naidu, Revathi; Volobujeva, Olga; Tverjanovich, Andrey; Kois, Julia

2017-12-01

Zinc oxysulfide - Zn(O,S) is one of the prospective materials for substitution of conventional CdS buffer layer in complete optoelectronic devices due to its optimal bandgap and low toxicity. In this work Zn(O,S) thin films have been prepared by one-step pulsed laser deposition technique. The films with a thickness of 650 nm were deposited onto the FTO/glass substrates at different substrate temperatures from room temperature to 400 °C. Zn(O,S) layers were characterized by means of scanning electron microscopy, energy dispersive spectroscopy, Raman, X-ray diffraction, UV-vis spectroscopy and Van der Pauw technique. It was found, that obtained Zn(O,S) layers are mainly polycrystalline, highly uniform, transparent, electrically conductive and demonstrate good adhesion to the FTO/glass substrates. In addition, we show that elemental composition of PLD Zn(O,S) films depends on the substrate temperature. For the first time high quality single phase conductive Zn(O,S) layers were prepared by one stage PLD in high vacuum at relatively low temperature 200 °C without any post treatment. The properties of prepared Zn(O,S) films suggest that these films can be applied as buffer layer in optoelectronic devices.

Preparation and characterization of sprayed FTO thin films

NASA Astrophysics Data System (ADS)

Abd-Lefdil, M.; Diaz, R.; Bihri, H.; Aouaj, M. Ait; Rueda, F.

2007-06-01

Fluorine doped tin oxide (FTO) thin films have been prepared by spray pyrolysis technique with no further annealing. Films with 2.5% of fluorine grown at 400 °C present a single phase and exhibit a tetragonal structure with lattice parameters a = 4.687 Å and c = 3.160 Å. Scanning electron micrographs showed homogeneous surfaces with average grain size around 190 nm. The films are transparent in the visible zone and exhibit a high reflectance in the near infrared region. The best electrical resistivity was 6.3 × 10-4 Ω cm for FTO with 2.5% of fluorine. The ratio of transmittance in the visible to the sheet resistance are in the 0.57 × 10-2 1.96 × 10-2 {Ω }-1 range.

Insights into the enhanced photoelectrochemical performance of hydrothermally controlled hematite nanostructures for proficient solar water oxidation.

PubMed

Park, Jin Woo; Subramanian, Arunprabaharan; Mahadik, Mahadeo A; Lee, Su Yong; Choi, Sun Hee; Jang, Jum Suk

2018-03-28

In this paper, we focus on the controlled growth mechanism of α-Fe 2 O 3 nanostructures via the hydrothermal method. The field emission scanning electron microscopy (FESEM) results reveal that at a lower hydrothermal time, the initial nucleation involves the formation of short and thin β-FeOOH nanorods. The subsequent increase in the hydrothermal time leads β-FeOOH to form thicker and longer nanorods. However, high-temperature quenching (HTQ) at 800 °C for 10 min causes the conversion of akaganeite to the hematite phase and activation of hematite by Sn 4+ diffusion from a FTO substrate. Sn 4+ diffusion from the FTO substrate to the hematite nanostructure was elaborated by X-ray photoelectron spectroscopy (XPS). An α-Fe 2 O 3 nanorod photoanode prepared by a hydrothermal reaction for 3 h and HTQ exhibits the highest photocurrent density of 1.04 mA cm -2 . The excellent photoelectrochemical performance could be ascribed to the synergistic effect of the optimum growth of α-Fe 2 O 3 nanorod arrays and Sn 4+ diffusion. Intensity modulated photovoltage spectroscopy (IMVS) studies revealed that the α-Fe 2 O 3 photoanodes prepared at 3 h and HTQ exhibited a long electron lifetime (132.69 ms), and contribute to the enhanced PEC performance. The results confirmed that the controlled growth of the β-FeOOH nanorods, as well as Sn 4+ diffusion, played a key role in charge transfer during the photoelectrochemical application. The charge transfer mechanisms in α-Fe 2 O 3 nanostructure photoanodes prepared at different hydrothermal times and high-temperature quenching are also investigated.

Facile synthesis of one dimensional ZnO nanostructures for DSSC applications

NASA Astrophysics Data System (ADS)

Marimuthu, T.; Anandhan, N.

2016-05-01

Development of zinc oxide (ZnO) nanostructure based third generation dye sensitized solar cell is interesting compared to conventional silicon solar cells. ZnO nanostructured thin films were electrochemically deposited onto fluorine doped tin oxide (FTO) glass substrate. The effect of ethylene-diamine-tetra-acetic acid (EDTA) on structural, morphological and optical properties is investigated using X-ray diffraction (XRD) meter, field emission scanning electron microscope (FE-SEM) and micro Raman spectroscopy. XRD patterns reveal that the prepared nanostructures are hexagonal wutrzite structures with (101) plane orientation, the nanostructure prepared using EDTA exhibits better crystallinity. FE-SEM images illustrate that the morphological changes are observed from nanorod structure to cauliflower like structure as EDTA is added. Micro Raman spectra predict that cauliflower like structure possesses a higher crystalline nature with less atomic defects compared to nanorod structures. Dye sensitized solar cell (DSSC) is constructed for the optimized cauliflower structure, and open circuit voltage, short circuit density, fill factor and efficiency are estimated from the J-V curve.

Growth and properties of electrodeposited transparent Al-doped ZnO nanostructures

NASA Astrophysics Data System (ADS)

Baka, O.; Mentar, L.; Khelladi, M. R.; Azizi, A.

2015-12-01

Al-doped zinc oxide (AZO) nanostructures were fabricated on fluorine-doped tin-oxide (FTO)- coated glass substrates by using electrodeposition. The effects of the doping concentration of Al on the morphological, microstructural, electrical and optical properties of the nanostructures were investigated. From the field emission scanning electron microscopy (FE-SEM) observation, when the amount of Al was increased in the solution, the grains size was observed to decreases. The observed changes in the morphology indicate that Al acts as nucleation centers in the vacancy sites of ZnO and destroys the crystalline structure at high doping level. Effectively, the X-ray diffraction (XRD) analysis indicated that the undoped and the doped ZnO nanostructures has a polycrystalline nature and a hexagonal wurtzite structure with a (002) preferential orientation. The photoluminescence (PL) room-temperature measurements showed that the incorporation of Al in the Zn lattice can improve the intensity of ultraviolet (UV) emission, thus suggesting its greater prospects for use in UV optoelectronic devices.

Modified band alignment effect in ZnO/Cu2O heterojunction solar cells via Cs2O buffer insertion

NASA Astrophysics Data System (ADS)

Eom, Kiryung; Lee, Dongyoon; Kim, Seunghwan; Seo, Hyungtak

2018-02-01

The effects of a complex buffer layer of cesium oxide (Cs2O) on the photocurrent response in oxide heterojunction solar cells (HSCs) were investigated. A p-n junction oxide HSC was fabricated using p-type copper (I) oxide (Cu2O) and n-type zinc oxide (ZnO); the buffer layer was inserted between the Cu2O and fluorine-doped tin oxide (FTO). Ultraviolet-visible (UV-vis) and x-ray and ultraviolet photoelectron spectroscopy analyses were performed to characterize the electronic band structures of cells, both with and without this buffer layer. In conjunction with the measured band electronic structures, the significantly improved visible-range photocurrent spectra of the buffer-inserted HSC were analyzed in-depth. As a result, the 1 sun power conversion efficiency was increased by about three times by the insertion of buffer layer. The physicochemical origin of the photocurrent enhancement was mainly ascribed to the increased photocarrier density in the buffer layer and modified valence band offset to promote the effective hole transfer at the interface to FTO on the band-alignment model.

Optically transparent cathode for Co(III/II) mediated dye-sensitized solar cells based on graphene oxide.

PubMed

Kavan, Ladislav; Yum, Jun-Ho; Graetzel, Michael

2012-12-01

Thin semitransparent films were fabricated on F-doped SnO(2) (FTO) from single-layer graphene oxide (GO) either pure or in a composite with graphene nanoplatelets. Electrocatalytic activity of prepared films was tested for the Co(bpy)(3)(3+/2+) redox couple in acetonitrile electrolyte solution. Pristine GO showed almost no activity, resembling the properties of basal plane pyrolytic graphite. However, electrochemical performance of graphene oxide improved dramatically upon chemical reduction with hydrazine and/or heat treatment. All GO-containing films were firmly bonded to FTO, which contrasted with the poor adhesion of sole graphene nanoplatelets to this support. The activity loss during long-term aging was considerably improved, too. Enhanced stability of GO-containing films together with high electrocatalytic activity is beneficial for application in a new generation of dye-sensitized solar cells employing Co(bpy)(3)(3+/2+) as the redox shuttle.

An artificial photosynthesis anode electrode composed of a nanoparticulate photocatalyst film in a visible light responsive GaN-ZnO solid solution system

PubMed Central

Imanaka, Yoshihiko; Anazawa, Toshihisa; Manabe, Toshio; Amada, Hideyuki; Ido, Sachio; Kumasaka, Fumiaki; Awaji, Naoki; Sánchez-Santolino, Gabriel; Ishikawa, Ryo; Ikuhara, Yuichi

2016-01-01

The artificial photosynthesis technology known as the Honda-Fujishima effect, which produces oxygen and hydrogen or organic energy from sunlight, water, and carbon dioxide, is an effective energy and environmental technology. The key component for the higher efficiency of this reaction system is the anode electrode, generally composed of a photocatalyst formed on a glass substrate from electrically conductive fluorine-doped tin oxide (FTO). To obtain a highly efficient electrode, a dense film composed of a nanoparticulate visible light responsive photocatalyst that usually has a complicated multi-element composition needs to be deposited and adhered onto the FTO. In this study, we discovered a method for controlling the electronic structure of a film by controlling the aerosol-type nanoparticle deposition (NPD) condition and thereby forming films of materials with a band gap smaller than that of the prepared raw material powder, and we succeeded in extracting a higher current from the anode electrode. As a result, we confirmed that a current approximately 100 times larger than those produced by conventional processes could be obtained using the same material. This effect can be expected not only from the materials discussed (GaN-ZnO) in this paper but also from any photocatalyst, particularly materials of solid solution compositions. PMID:27759108

Single-layer graphene/titanium oxide cubic nanorods array/FTO heterojunction for sensitive ultraviolet light detection

NASA Astrophysics Data System (ADS)

Liang, Feng-Xia; Wang, Jiu-Zhen; Wang, Yi; Lin, Yi; Liang, Lin; Gao, Yang; Luo, Lin-Bao

2017-12-01

In this study, we report on the fabrication of a sensitive ultraviolet photodetector (UVPD) by simply transferring single-layer graphene (SLG) on rutile titanium oxide cubic nanorod (TiO2NRs) array. The cubic TiO2NRs array with strong light trapping effect was grown on fluorine-doped tin oxide (FTO) glass through a hydrothermal approach. The as-assembled UVPD was very sensitive to UV light illumination, but virtually blind to white light illumination. The responsivity and specific detectivity were estimated to be 52.1 A/W and 4.3 × 1012 Jones, respectively. What is more, in order to optimize device performance of UVPD, a wet-chemistry treatment was then employed to reduce the high concentration of defects in TiO2NRs during hydrothermal growth. It was found that the UVPD after treatment showed obvious decrease in sensitivity, but the response speed (rise time: 80 ms, fall time: 160 ms) and specific detectivity were substantially increased. It is also found that the speicific detectivity was imporoved by six-fold to 3.2 × 1013 Jones, which was the best result in comparison with previously reported TiO2 nanostructures or thin film based UVPDs. This totality of this study shows that the present SLG/TiO2NR/FTO UVPD may find potential application in future optoelectronic devices and systems.

Single crystalline CH 3NH 3PbI 3 self-grown on FTO/TiO 2 substrate for high efficiency perovskite solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Jinjin; Kong, Guoli; Chen, Shulin

In this work, we developed an innovative approach to self-grow single crystalline CH 3NH 3PbI 3 directly on polycrystalline FTO/TiO 2 substrate, with which n-i-p type of perovskite solar cells were fabricated. The single crystalline nature of CH 3NH 3PbI 3 has been confirmed by X-ray diffraction and high resolution transmission electron microscopy, and it is observed that they possess smaller optic band gap and longer carrier life time. Highly efficient charge extractions occur at the interface between electron collecting TiO 2 and photo-harvesting CH 3NH 3PbI 3, resulting in a maximum short-circuit current density of 24.40 mA/cm 2. Themore » champion cell possesses a photovoltaic conversion efficiency of 8.78%, and there are still substantial room for further improvement, making it promising for the perovskite solar cell applications.« less

Single crystalline CH 3NH 3PbI 3 self-grown on FTO/TiO 2 substrate for high efficiency perovskite solar cells

DOE PAGES

Zhao, Jinjin; Kong, Guoli; Chen, Shulin; ...

2017-08-21

In this work, we developed an innovative approach to self-grow single crystalline CH 3NH 3PbI 3 directly on polycrystalline FTO/TiO 2 substrate, with which n-i-p type of perovskite solar cells were fabricated. The single crystalline nature of CH 3NH 3PbI 3 has been confirmed by X-ray diffraction and high resolution transmission electron microscopy, and it is observed that they possess smaller optic band gap and longer carrier life time. Highly efficient charge extractions occur at the interface between electron collecting TiO 2 and photo-harvesting CH 3NH 3PbI 3, resulting in a maximum short-circuit current density of 24.40 mA/cm 2. Themore » champion cell possesses a photovoltaic conversion efficiency of 8.78%, and there are still substantial room for further improvement, making it promising for the perovskite solar cell applications.« less

High efficient perovskite solar cell material CH3NH3PbI3: Synthesis of films and their characterization

NASA Astrophysics Data System (ADS)

Bera, Amrita Mandal; Wargulski, Dan Ralf; Unold, Thomas

2018-04-01

Hybrid organometal perovskites have been emerged as promising solar cell material and have exhibited solar cell efficiency more than 20%. Thin films of Methylammonium lead iodide CH3NH3PbI3 perovskite materials have been synthesized by two different (one step and two steps) methods and their morphological properties have been studied by scanning electron microscopy and optical microscope imaging. The morphology of the perovskite layer is one of the most important parameters which affect solar cell efficiency. The morphology of the films revealed that two steps method provides better surface coverage than the one step method. However, the grain sizes were smaller in case of two steps method. The films prepared by two steps methods on different substrates revealed that the grain size also depend on the substrate where an increase of the grain size was found from glass substrate to FTO with TiO2 blocking layer to FTO without any change in the surface coverage area. Present study reveals that an improved quality of films can be obtained by two steps method by an optimization of synthesis processes.

Temperature-dependent photoluminescence analysis of ZnO nanowire array annealed in air

NASA Astrophysics Data System (ADS)

Sun, Yanan; Gu, Xiuquan; Zhao, Yulong; Wang, Linmeng; Qiang, Yinghuai

2018-05-01

ZnO nanowire arrays (NWAs) were prepared on transparent conducting fluorine doped tin oxide (FTO) substrates through a facile hydrothermal method, followed by a 500 °C annealing to improve their crystalline qualities and photoelectrochemical (PEC) activities. It was found that the annealing didn't change the morphology, but resulted in a significant reduction of the donor concentration. Temperature-dependent photoluminescence (PL) was carried out for a comprehensive analysis of the effect from annealing. Noteworthy, four dominant peaks were identified from the 10 K spectrum of a 500 °C annealed sample, and they were assigned to FX, D0X, (e, D0) and (e, D0) -1LO, respectively. Of them, the FX emission was only existed below 130 K, while the room-temperature (RT) PL spectrum was dominated by the D0X emission.

Structural and optical properties of nanostructured CdSe thin films prepared by electrochemical deposition

NASA Astrophysics Data System (ADS)

Bai, Rekha; Chaudhary, Sujeet; Pandya, Dinesh K.

2018-05-01

Cadmium selenide (CdSe) nanostructured thin films have been grown on fluorine doped tin oxide (FTO) coated glass substrates by potentiostatic electrochemical deposition (ECD) technique for use in solar energy conversion devices. The effect of bath temperature on the structural, morphological and optical properties of prepared CdSe films has been explored. X-ray diffraction (XRD) and Raman spectroscopy clearly show that the CdSe films are polycrystalline and exhibit phase transformation from wurtzite to zincblende structure with increase in bath temperature. Optical spectra reveal that the nanostructured CdSe films have high absorbance in visible region and the films show a red shift in direct optical energy band gap from 1.90 to 1.65 eV with increase in bath temperature due to change in phase and bandgap tuning related to quantum confinement effect.

Electrical characterization of ZnO/NiO p-n junction prepared by the sol-gel method

NASA Astrophysics Data System (ADS)

Merih Akyuzlu, A.; Dagdelen, Fethi; Gultek, Ahmet; Hendi, A. A.; Yakuphanoglu, Fahrettin

2017-04-01

ZnO and NiO films were synthesized on fluourine-doped tin oxide (FTO) glass substrate by the sol-gel method. The surface morphology of the films was investigated by atomic force microscopy. The optical band gaps of the ZnO and NiO films were found to be 3.198 and 3.827eV, respectively. A ZnO/NiO p-n junction diode was prepared and electrical charge transport mechanism of the diode was analyzed using thermionic emission and Norde functions. The ideality factor, barrier height and series resistance of the diode were determined to be 6.46, 1.036eV and 39.1 M {Ω} , respectively. The obtained results indicate that ZnO/NiO p-n junction can be used as transparent diode for optic communications.

Nanostructure CdS/ZnO heterojunction configuration for photocatalytic degradation of Methylene blue

NASA Astrophysics Data System (ADS)

Velanganni, S.; Pravinraj, S.; Immanuel, P.; Thiruneelakandan, R.

2018-04-01

In the present manuscript, thin films of Zinc Oxide (ZnO) have been deposited on a FTO substrate using a simple successive ionic layer adsorption and reaction (SILAR) and chemical bath deposition (CBD) method. Cadmium Sulphide (CdS) nanoparticles are sensitized over ZnO thin films using SILAR method. The synthesized nanostructured CdS/ZnO heterojunction thin films was characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), High resolution transmission electron microscopy (HR-TEM), X-ray photoelectron spectroscopy (XPS), UV-Vis spectroscopy and Raman spectroscopy techniques. The band gap of CdS nanoparticles over ZnO nanostructure was found to be about 3.20 eV. The photocatalytic activities of the deposited CdS/ZnO thin films were evaluated by the degradation of methylene blue (MB) in an aqueous solution under sun light irradiation.

Hierarchical cobalt-based hydroxide microspheres for water oxidation.

PubMed

Zhang, Ye; Cui, Bai; Derr, Olivia; Yao, Zhibo; Qin, Zhaotong; Deng, Xiangyun; Li, Jianbao; Lin, Hong

2014-03-21

3D hierarchical cobalt hydroxide carbonate hydrate (Co(CO3)0.5(OH)·0.11H2O) has been synthesized featuring a hollow urchin-like structure by a one-step hydrothermal method at modest temperature on FTO glass substrates. The functionalities of precursor surfactants were isolated and analyzed. A plausible formation mechanism of the spherical urchin-like microclusters has been furnished through time-dependent investigations. Introduction of other transitional metal doping (Cu, Ni) would give rise to a substantial morphological change associated with a surface area drop. The directly grown cobalt-based hydroxide composite electrodes were found to be capable of catalyzing oxygen evolution reaction (OER) under both neutral pH and alkaline conditions. The favorable 3D dendritic morphology and porous structure provide large surface areas and possible defect sites that are likely responsible for their robust electrochemical activity.

Perovskite solar cells based on nanocolumnar plasma-deposited ZnO thin films.

PubMed

Ramos, F Javier; López-Santos, Maria C; Guillén, Elena; Nazeeruddin, Mohammad Khaja; Grätzel, Michael; Gonzalez-Elipe, Agustin R; Ahmad, Shahzada

2014-04-14

ZnO thin films having a nanocolumnar microstructure are grown by plasma-enhanced chemical vapor deposition at 423 K on pre-treated fluorine-doped tin oxide (FTO) substrates. The films consist of c-axis-oriented wurtzite ZnO nanocolumns with well-defined microstructure and crystallinity. By sensitizing CH3NH3PbI3 on these photoanodes a power conversion of 4.8% is obtained for solid-state solar cells. Poly(triarylamine) is found to be less effective when used as the hole-transport material, compared to 2,2',7,7'-tetrakis(N,N-di-p-methoxyphenylamine)-9,9'-spirobifluorene (spiro-OMeTAD), while the higher annealing temperature of the perovskite leads to a better infiltration in the nanocolumnar structure and an enhancement of the cell efficiency. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enhanced photovoltaic performance of dye-sensitized solar cells based on nickel oxide supported on nitrogen-doped graphene nanocomposite as a photoanode.

PubMed

Ranganathan, Palraj; Sasikumar, Ragu; Chen, Shen-Ming; Rwei, Syang-Peng; Sireesha, Pedaballi

2017-10-15

We applied the nitrogen-doped graphene@nickel oxide (NGE/NiO) nanocomposite doped TiO 2 as a photo-anode for dye-sensitized solar cells (DSSCs) on fluorine-doped tin oxide (FTO) substrates by screen printing method. Power conversion efficiency (PCE) of 9.75% was achieved for this DSSCs device, which is greater than that of DSSCs devices using GO/TiO 2 , and NiO/TiO 2 based photo-anodes (PCE=8.55, and 9.11%). Also, the fill factor (FF) of the DSSCs devices using the NGE/NiO/TiO 2 nanocomposite photo-anode was better than that of other photo-anodes. The NGE/NiO/TiO 2 short-circuit photocurrent density (J sc ) of 19.04mAcm -2 , open circuit voltage (V oc ) of 0.76V, fill factor (FF) of 0.67 and dye absorption rate 0.21×10 -6 molcm -2 . The obtained results suggest that as-prepared NGE/NiO/TiO 2 nanocomposite is suitable photo-anode for DSSCs application. Copyright © 2017 Elsevier Inc. All rights reserved.

Association of FTO rs9939609 with Obesity.

PubMed

Yasri, Sora; Wiwanitkit, Viroj

2018-05-30

Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity

Materials (Subjects) and Methods

Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity

Results:

Association of FTO rs9939609 with Obesity

Conclusion:

Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity Association of FTO rs9939609 with Obesity. ©2018The Author(s). Published by S. Karger AG, Basel.

Effect of Substrates on the Photoelectrochemical Reduction of Water over Cathodically Electrodeposited p-Type Cu2O Thin Films.

PubMed

Shyamal, Sanjib; Hajra, Paramita; Mandal, Harahari; Singh, Jitendra Kumar; Satpati, Ashis Kumar; Pande, Surojit; Bhattacharya, Chinmoy

2015-08-26

In this study, we demonstrate development of p-Cu2O thin films through cathodic electrodeposition technique at constant current of 0.1 mA/cm(2) on Cu, Al, and indium tin oxide (ITO) substrates from basic CuSO4 solution containing Triton X-100 as the surfactant at 30-35 °C. The optical and morphological characterizations of the semiconductors have been carried out using UV-vis spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and Raman spectroscopy. The band gap energy of ∼2.1 eV is recorded, whereas SEM reveals that the surface morphology is covered with Cu2O semiconductors. XRD analyses confirm that with change in substrate, the size of Cu2O "cubic" crystallites decreases from ITO to Al to Cu substrates. Photoelectrochemical characterizations under dark and illuminated conditions have been carried out through linear sweep voltammetry, chronoamperometry and electrochemical impedance spectroscopic analysis. The photoelectrochemical reduction of water (H2O → H2) in pH 4.9 aqueous solutions over the different substrates vary in the order of Cu > Al > ITO. The highest current of 4.6 mA/cm(2) has been recorded over the Cu substrate even at a low illumination of 35 mW/cm(2), which is significantly higher than the values (2.4 mA/cm(2) on Au coated FTO or 4.07 mA/cm(2) on Cu foil substrate at an illumination of 100 mW/cm(2)) reported in literature.

Cobalt oxide acicular nanorods with high sensitivity for the non-enzymatic detection of glucose.

PubMed

Kung, Chung-Wei; Lin, Chia-Yu; Lai, Yi-Hsuan; Vittal, R; Ho, Kuo-Chuan

2011-09-15

Acicular cobalt oxide nanorods (CoONRs) were prepared for the non-enzymatic detection of glucose, first by directly growing layered cobalt carbonate hydroxide (LCCH) on a conducting fluorine-doped tin oxide (FTO) substrate using a simple chemical bath deposition (CBD) technique and then by transforming the LCCH into CoONRs through pyrolysis. The composition and grain size of the films of LCCH and CoONRs were verified by X-ray diffraction (XRD); their morphologies were examined by scanning electron microscopic (SEM) and transmission electron microscopic (TEM) images. CoONRs showed high electrocatalytic activity for the electro-oxidation of glucose in alkaline media, and the activity was strongly influenced by NaOH concentration, annealing temperature of CoONRs, and thickness of CoONRs film. The pertinent sensor could be successfully used for the quantification of glucose by amperometric method. The sensing parameters include wide linear range up to 3.5 mM, a high sensitivity of 571.8 μA/(cm(2) mM), and a remarkable low detection limit of 0.058 μM. The CoONRs modified electrode exhibited a high selectivity for glucose in human serum, against ascorbic acid, uric acid, and acetaminophen. Copyright © 2011 Elsevier B.V. All rights reserved.

Influence of Preferred Orientation on the Electrical Conductivity of Fluorine-Doped Tin Oxide Films

PubMed Central

Wang, Jian Tao; Shi, Xiang Lei; Liu, Wei Wei; Zhong, Xin Hua; Wang, Jian Nong; Pyrah, Leo; Sanderson, Kevin D.; Ramsey, Philip M.; Hirata, Masahiro; Tsuri, Keiko

2014-01-01

Current development of high-performance transparent conductive oxide (TCO) films is limited with tradeoff between carrier mobility and concentration since none of them can be improved without sacrificing the other. In this study, we prepare fluorine doped tin oxide (FTO) films by chemical vapor deposition with inclusions of different additives and report that the mobility can be varied from 0.65 to 28.5 cm2 V−1 s−1 without reducing the achieved high carrier concentration of 4 × 1020 cm−3. Such an increase in mobility is shown to be clearly associated with the development of (200) preferred orientation (PO) but concurrent degradation of (110) PO in films. Thus, at a constant high carrier concentration, the electrical conductivity can be improved via carrier mobility simply by PO control. Such a one-step approach avoiding conventional post-deposition treatment is suggested for developing next-generation FTO as well as other TCO films with better than ever conductivities. PMID:24419455

Urea impedimetric biosensing using electrospun nanofibers modified with zinc oxide nanoparticles

NASA Astrophysics Data System (ADS)

Migliorini, Fernanda L.; Sanfelice, Rafaela C.; Mercante, Luiza A.; Andre, Rafaela S.; Mattoso, Luiz H. C.; Correa, Daniel. S.

2018-06-01

Reliable analytical techniques to evaluate dairy products, including milk, are of outmost importance to ensure food safety against contaminants. Among possible substances employed as adulterants in milk, urea raises deep concern due to its harmful effects to consumer's health. In the present study, a biosensing platform was developed to be applied in the electrochemical detection of urea. The sensing platform was fabricated using polymeric electrospun nanofibers of polyamide 6 (PA6) and polypyrrole (PPy) deposited onto fluorine doped tin oxide (FTO) electrodes, which were then modified with zinc oxide nanoparticles (ZnO). This material showed excellent properties for the immobilization of urease enzyme, conferring the FTO/PA6/PPy/ZnO/urease electrode high sensitivity for urea detection within the concentration range between 0.1 and 250 mg dL-1 with a limit of detection of 0.011 mg dL-1. The results achieved evidence the potential of electrospun nanofibers-based electrodes for applications in biosensors aiming at dairy products analysis.

Scale-Up of the Electrodeposition of ZnO/Eosin Y Hybrid Thin Films for the Fabrication of Flexible Dye-Sensitized Solar Cell Modules.

PubMed

Bittner, Florian; Oekermann, Torsten; Wark, Michael

2018-02-02

The low-temperature fabrication of flexible ZnO photo-anodes for dye-sensitized solar cells (DSSCs) by templated electrochemical deposition of films was performed in an enlarged and technical simplified deposition setup to demonstrate the feasibility of the scale-up of the deposition process. After extraction of eosin Y (EY) from the initially deposited ZnO/EY hybrid films, mesoporous ZnO films with an area of about 40 cm² were reproducibly obtained on fluorine doped tin oxide (FTO)-glass as well as flexible indium tin oxide (ITO)-polyethylenterephthalate (PET) substrates. With a film thickness of up to 9 µm and a high specific surface area of up to about 77 m²·cm -3 the ZnO films on the flexible substrates show suitable properties for DSSCs. Operative flexible DSSC modules proved the suitability of the ZnO films for use as DSSC photo-anodes. Under a low light intensity of about 0.007 sun these modules achieved decent performance parameters with conversion efficiencies of up to 2.58%. With rising light intensity the performance parameters deteriorated, leading to conversion efficiencies below 1% at light intensities above 0.5 sun. The poor performance of the modules under high light intensities can be attributed to their high series resistances.

Scale-Up of the Electrodeposition of ZnO/Eosin Y Hybrid Thin Films for the Fabrication of Flexible Dye-Sensitized Solar Cell Modules

PubMed Central

Oekermann, Torsten

2018-01-01

The low-temperature fabrication of flexible ZnO photo-anodes for dye-sensitized solar cells (DSSCs) by templated electrochemical deposition of films was performed in an enlarged and technical simplified deposition setup to demonstrate the feasibility of the scale-up of the deposition process. After extraction of eosin Y (EY) from the initially deposited ZnO/EY hybrid films, mesoporous ZnO films with an area of about 40 cm2 were reproducibly obtained on fluorine doped tin oxide (FTO)-glass as well as flexible indium tin oxide (ITO)–polyethylenterephthalate (PET) substrates. With a film thickness of up to 9 µm and a high specific surface area of up to about 77 m2·cm−3 the ZnO films on the flexible substrates show suitable properties for DSSCs. Operative flexible DSSC modules proved the suitability of the ZnO films for use as DSSC photo-anodes. Under a low light intensity of about 0.007 sun these modules achieved decent performance parameters with conversion efficiencies of up to 2.58%. With rising light intensity the performance parameters deteriorated, leading to conversion efficiencies below 1% at light intensities above 0.5 sun. The poor performance of the modules under high light intensities can be attributed to their high series resistances. PMID:29393910

One-Pot Solvothermal in Situ Growth of 1D Single-Crystalline NiSe on Ni Foil as Efficient and Stable Transparent Conductive Oxide Free Counter Electrodes for Dye-Sensitized Solar Cells.

PubMed

Bao, Chao; Li, Faxin; Wang, Jiali; Sun, Panpan; Huang, Niu; Sun, Yihua; Fang, Liang; Wang, Lei; Sun, Xiaohua

2016-12-07

One-dimensional single-crystal nanostructural nickel selenides were successfully in situ grown on metal nickel foils by two simple one-step solvothermal methods, which formed NiSe/Ni counter electrodes (CEs) for dye-sensitized solar cells (DSSCs). The nickel foil acted as the nickel source in the reaction process, a supporting substrate, and an electron transport "speedway". Electrochemical testing indicated that the top 1D single-crystal NiSe exhibited prominent electrocatalytic activity for I 3 - reduction. Due to the metallic conductivity of Ni substrate and the outstanding electrocatalytic activity of single-crystal NiSe, the DSSC based on a NiSe/Ni CE exhibited higher fill factor (FF) and larger short-circuit current density (J sc ) than the DSSC based on Pt/FTO CE. The corresponding power conversion efficiency (6.75%) outperformed that of the latter (6.18%). Moreover, the NiSe/Ni CEs also showed excellent electrochemical stability in the I - /I 3 - redox electrolyte. These findings indicated that single-crystal NiSe in situ grown on Ni substrate was a potential candidate to replace Pt/TCO as a cheap and highly efficient counter electrode of DSSC.

Growth of highly textured PbTiO3 films on conductive substrate under hydrothermal conditions

NASA Astrophysics Data System (ADS)

Tang, Haixiong; Zhou, Zhi; Bowland, Christopher C.; Sodano, Henry A.

2015-08-01

Perovskite structure (ABO3) thin films have wide applications in electronic devices due to their unique properties, including high dielectric permittivity, ferroelectricity and piezoelectric coupling. Here, we report an approach to grow highly textured thick lead titanate (PbTiO3) films on conductive substrates by a two-step hydrothermal reaction. Initially, vertically aligned TiO2 nanowire arrays are grown on fluorine-doped tin oxide (FTO) coated glass, which act as template crystals for conversion to the perovskite structure. The PbTiO3 films are then converted from TiO2 NW arrays by diffusing Pb2+ ions into the template through a second hydrothermal reaction. The dielectric permittivity and piezoelectric coupling coefficient (d33) of the PbTiO3 films are as high as 795 at 1 kHz and 52 pm V-1, respectively. The reported process can also potentially be expanded for the assembly of other complex perovskite ATiO3 (A = Ba, Ca, Cd, etc) films by using the highly aligned TiO2 NW arrays as templates. Therefore, the approach introduced here opens up a new door to synthesize ferroelectric thin films on conductive substrates for application in sensors, actuators, and ultrasonic transducers that are important in various industrial and scientific areas.

Effect of the polymeric coating thickness on the photocurrent performance of titanium dioxide nanorod arrays-polyaniline composite-based UV photosensor

NASA Astrophysics Data System (ADS)

Yusoff, M. M.; Mamat, M. H.; Malek, M. F.; Othman, , N.; Ismail, A. S.; Saidi, S. A.; Mohamed, R.; Suriani, A. B.; Khusaimi, Z.; Rusop, M.

2018-05-01

Titanium dioxide (TiO2) nanorod arrays (TNAs) were synthesized and deposited on fluorine tin oxide (FTO)-coated glass substrate using a one-step immersion method in a glass container. The effect of the polymeric coating thickness of p-type polyaniline (PANI) on the n-type TNAs was investigated in the p-n heterojunction photodiode (PD) for the application of ultraviolet (UV) photosensor. The fabricated photosensor demonstrated an increased photocurrent under UV irradiation in correlation with the thickness layer of PANI. The measured UV response showed the highest photocurrent of 0.014 µA at 1.0 V of reverse bias with low dark current under the UV radiation (365 nm, 750 µW/cm2). The thickness of the PANI film improved the photocurrent of the fabricated TNAs/PANI composite-based UV photosensor.

Comparison of photovoltaic properties of TiO2 electrodes prepared with nanoparticles and nanorods.

PubMed

Nam, Sang-Hun; Ju, Dong-Woo; Boo, Jin-Hyo

2014-12-01

In this report, single crystalline rutile TiO2 nanoparticles and nanorods were synthesized via the hydrothermal method using titanium tetra-isopropoxide as a precursor then, these were coated on top of a fluorine-doped tin oxide (FTO) substrate by using a doctor blade and direct deposition, respectively. Consequently, TiO2 nanorods-based dye-sensitized solar cells (DSSC) exhibit a J(sc) of 3.37 mA/cm2, a V(oc) of 0.82 V and fill factor of 60.1% with an overall conversion efficiency of 1.66%. This result shows an increase of around 38% for current density and 35% for conversion efficiency. Also, with respect to the impedance data, TiO2 nanorods-based DSSCs had smaller semicircles than did the nanoparticles-based DSSCs. These results demonstrate that the nanorod structure can have fast electron transport and reduced charge recombination.

Optical properties of anthocyanin dyes on TiO2 as photosensitizers for application of dye-sensitized solar cell (DSSC)

NASA Astrophysics Data System (ADS)

Ahliha, A. H.; Nurosyid, F.; Supriyanto, A.; Kusumaningsih, T.

2018-03-01

Dye-sensitized solar cell (DSSC) is one of the alternative energy that can convert light energy into electrical energy. The component of DSSC consists of FTO substrates, TiO2, electrolyte, dye sensitizer, and counter electrode. This study aim was to determine the effect of optical properties of anthocyanin dyes on efficiency of DSSC. The dye sensitizer used can be extracted from anthocyanin pigments such as dragon fruit, black rice, and red cabbage. The red cabbage sensitizer shows lower absorbance value in the visible range (450-580 nm), than dragon fruit and black rice. The chemical structure of each dye molecules has an R group (carbonyl and hydroxyl) that forms a bond with the oxide layer. Red cabbage dye cell has the highest efficiency, 0.06% then dragon fruit and black rice, 0.02% and 0.03%.

Preparation of Sb2S3 nanocrystals modified TiO2 dendritic structure with nanotubes for hybrid solar cell

NASA Astrophysics Data System (ADS)

Li, Yingpin; Wei, Yanan; Feng, Kangning; Hao, Yanzhong; Pei, Juan; Sun, Bao

2018-06-01

Array of TiO2 dendritic structure with nanotubes was constructed on transparent conductive fluorine-doped tin oxide glass (FTO) with titanium potassium oxalate as titanium source. Sb2S3 nanocrystals were successfully deposited on the TiO2 substrate via spin-coating method. Furthermore, TiO2/Sb2S3/P3HT/PEDOT:PSS composite film was prepared by successively spin-coating P3HT and PEDOT:PSS on TiO2/Sb2S3. It was demonstrated that the modification of TiO2 dendritic structure with Sb2S3 could enhance the light absorption in the visible region. The champion hybrid solar cell assembled by TiO2/Sb2S3/P3HT/PEDOT:PSS composite film achieved a power conversion efficiency (PCE) of 1.56%.

Dip-Coating Process Engineering and Performance Optimization for Three-State Electrochromic Devices

NASA Astrophysics Data System (ADS)

Wu, Lu; Yang, Dejiang; Fei, Lixun; Huang, Yue; Wu, Fang; Sun, Yiling; Shi, Jiayuan; Xiang, Yong

2017-06-01

Titanium dioxide (TiO2) nanoparticles were modified onto fluorine-doped tin oxide (FTO) via dip-coating technique with different nanoparticle sizes, lifting speeds, precursor concentrations, and dipping numbers. Electrodeposition-based electrochromic device with reversible three-state optical transformation (transparent, mirror, and black) was fabricated subsequently by sandwiching a suitable amount of gel electrolyte between modified FTO electrode and flat FTO electrode. Correlation between dip-coating process engineering, morphological features of TiO2 thin films, i.e., thickness and roughness, as well as performance of electrochromic devices, i.e., optical contrast, switching time, and cycling stability, were investigated. The modified device exhibits high optical contrast of 57%, the short coloration/bleaching switching time of 6 and 20 s, and excellent cycling stability after 1500 cycles of only 27% decrement rate by adjusting dip-coating processes engineering. The results in this study will provide valuable guidance for rational design of the electrochromic device with satisfactory performance.

An investigation of the Nb doping effect on structural, morphological, electrical and optical properties of spray deposited F doped SnO2 films

NASA Astrophysics Data System (ADS)

Turgut, G.; Keskenler, E. F.; Aydın, S.; Yılmaz, M.; Doǧan, S.; Düzgün, B.

2013-03-01

F and Nb + F co-doped SnO2 thin films were deposited on glass substrates by the spray pyrolysis method. The microstructural, morphological, electrical and optical properties of the 10 wt% F doped SnO2 (FTO) thin films were investigated specifically for niobium (Nb) doping in the range of 0-4 at.% with 1 at.% steps. As shown by the x-ray diffraction patterns, the films exhibited a tetragonal cassiterite structure with (200) preferential orientation. It was observed that grain sizes of the films for (200) and (301) peaks depended on the Nb doping concentration and varied in the range of 25.11-32.19 and 100.6-183.7 nm, respectively. The scanning electron microscope (SEM) micrographs showed that the FTO films were made of small pyramidal grains, while doubly doped films were made of small pyramidal grains and big polyhedron grains. From electrical studies, although 1 at.% Nb doped FTO films have the lowest sheet resistance and resistivity values, the highest figure-of-merit and optical band gap values obtained for FTO films were 16.2 × 10-2 Ω-1 and 4.21 eV, respectively. Also, infrared reflectivity values of the films were in the range of 97.39-98.98%. These results strongly suggest that these films are an attractive candidate for various optoelectronic applications and for photothermal conversion of solar energy.

Morphology and Doping Engineering of Sn-Doped Hematite Nanowire Photoanodes.

PubMed

Li, Mingyang; Yang, Yi; Ling, Yichuan; Qiu, Weitao; Wang, Fuxin; Liu, Tianyu; Song, Yu; Liu, Xiaoxia; Fang, Pingping; Tong, Yexiang; Li, Yat

2017-04-12

High-temperature activation has been commonly used to boost the photoelectrochemical (PEC) performance of hematite nanowires for water oxidation, by inducing Sn diffusion from fluorine-doped tin oxide (FTO) substrate into hematite. Yet, hematite nanowires thermally annealed at high temperature suffer from two major drawbacks that negatively affect their performance. First, the structural deformation reduces light absorption capability of nanowire. Second, this "passive" doping method leads to nonuniform distribution of Sn dopant in nanowire and limits the Sn doping concentration. Both factors impair the electrochemical properties of hematite nanowire. Here we demonstrate a silica encapsulation method that is able to simultaneously retain the hematite nanowire morphology even after high-temperature calcination at 800 °C and improve the concentration and uniformity of dopant distribution along the nanowire growth axis. The capability of retaining nanowire morphology allows tuning the nanowire length for optimal light absorption. Uniform distribution of Sn doping enhances the donor density and charge transport of hematite nanowire. The morphology and doping engineered hematite nanowire photoanode decorated with a cobalt oxide-based oxygen evolution reaction (OER) catalyst achieves an outstanding photocurrent density of 2.2 mA cm -2 at 0.23 V vs Ag/AgCl. This work provides important insights on how the morphology and doping uniformity of hematite photoanodes affect their PEC performance.

Dual functional passivating layer of graphene/TiO2 for improved performance of dye-sensitized solar cells

NASA Astrophysics Data System (ADS)

Shahid, Muhammad Umair; Mohamed, Norani Muti; Muhsan, Ali Samer; Khatani, Mehboob; Bashiri, Robabeh; Zaine, Siti Nur Azella; Shamsudin, Adel Eskandar

2018-02-01

The FTO/TiO2 interface plays a crucial role in the performance of dye-sensitized solar cells (DSSCs). The uneven microstructure morphology of FTO (fluorine-doped tin oxide) glass surface and high porosity of TiO2 layer produce tiny gaps and voids at the FTO/TiO2 interface that breaks the connectivity, leading to an increase in the recombination process. In the current work, a dual functional passivating layer is introduced by the combination of the graphene/TiO2 compact layer. The excellent mobility and flexibility of graphene is capitalized using its layer to fill the voids in the FTO surface, which can consequently reduce the charge transfer resistance at the interface, while the added TiO2 compact layer avoids direct contact with the electrolyte thus reducing the recombination. Graphene was synthesized by the facile solvent exfoliation method with the assistance of the probe sonication process. The parameters of sonication were optimized to achieve high-quality concentrated graphene inks (0.177-0.51 mg/ml). Raman spectroscopy and transmission electron microscopy (TEM) revealed that the graphene obtained is of a few-layer type. Electrochemical impedance spectroscopy (EIS) analysis indicated that the incorporated compact layer of graphene/TiO2 was capable of accelerating the charge transfer and reducing the recombination process at the FTO/TiO2 interface. Consequently, the photoconversion efficiency (PCE) for the device (1 cm2 active area) with double-coated graphene layer under one sun irradiation (AM 1.5) was found to be 49.49% higher than the conventional one.

Macronutrient-specific effect of FTO rs9939609 in response to a 10-week randomized hypo-energetic diet among obese Europeans.

PubMed

Grau, K; Hansen, T; Holst, C; Astrup, A; Saris, W H M; Arner, P; Rössner, S; Macdonald, I; Polak, J; Oppert, J-M; Langin, D; Martinez, J A; Pedersen, O; Sørensen, T I A

2009-11-01

The A risk allele of rs9939609 of the fat mass- and obesity-associated gene (FTO) increases body fat mass. To examine whether FTO rs9939609 affects obese individuals' response to a high-fat, low-carbohydrate (CHO) (HF) or low-fat, high-CHO (LF), hypo-energetic diet and whether the effect of the FTO variant depends on dietary fat and CHO content. In a 10-week, European, multi-centre dietary intervention study 771 obese women and men were randomized to either LF (20-25% of energy (%E) from fat, 60-65%E from CHO) or HF (40-45%E from fat, 40-45%E from CHO), hypo-energetic diet (measured resting metabolic rate multiplied by 1.3-600 kcal day(-1)). Body weight, fat mass (FM), fat-free mass (FFM), waist circumference (WC), resting energy expenditure (REE), fasting fat oxidation as % of REE (FatOx), insulin release (HOMA-beta) and a surrogate measure of insulin resistance (HOMA-IR) were measured at baseline and after the intervention. In all, 764 individuals were genotyped for FTO rs9939609. For A-allele carriers the drop-out rate was higher on HF than LF diet (in AT, P=0.002; in AT/AA combined, P=0.003). Among those individuals completing the intervention, we found no effect of FTO rs9939609 genotype on Deltaweight, DeltaFM, DeltaFFM, DeltaWC or DeltaFatOx. However, participants with TT had a smaller reduction in REE on LF than on HF diet (75 kcal/24 h; interaction: P=0.0055). These individuals also showed the greatest reduction in HOMA-beta and HOMA-IR (interaction: P=0.0083 and P=0.047). The FTO rs9939609 may interact with the macronutrient composition in weight loss diets in various ways; carriers of the A allele on LF diet appear to have a lower risk for drop out, and TT individuals have a smaller decrease in REE and greater decrease in HOMA-beta and HOMA-IR on LF than on HF diet.

BiVO4 thin film photoanodes grown by chemical vapor deposition.

PubMed

Alarcón-Lladó, Esther; Chen, Le; Hettick, Mark; Mashouf, Neeka; Lin, Yongjing; Javey, Ali; Ager, Joel W

2014-01-28

BiVO4 thin film photoanodes were grown by vapor transport chemical deposition on FTO/glass substrates. By controlling the flow rate, the temperatures of the Bi and V sources (Bi metal and V2O5 powder, respectively), and the temperature of the deposition zone in a two-zone furnace, single-phase monoclinic BiVO4 thin films can be obtained. The CVD-grown films produce global AM1.5 photocurrent densities up to 1 mA cm(-2) in aqueous conditions in the presence of a sacrificial reagent. Front illuminated photocatalytic performance can be improved by inserting either a SnO2 hole blocking layer and/or a thin, extrinsically Mo doped BiVO4 layer between the FTO and the CVD-grown layer. The incident photon to current efficiency (IPCE), measured under front illumination, for BiVO4 grown directly on FTO/glass is about 10% for wavelengths below 450 nm at a bias of +0.6 V vs. Ag/AgCl. For BiVO4 grown on a 40 nm SnO2/20 nm Mo-doped BiVO4 back contact, the IPCE is increased to over 40% at wavelengths below 420 nm.

Morphology, structural and optical properties of iron oxide thin film photoanodes in photoelectrochemical cell: Effect of electrochemical oxidation

NASA Astrophysics Data System (ADS)

Maabong, Kelebogile; Machatine, Augusto G.; Hu, Yelin; Braun, Artur; Nambala, Fred J.; Diale, Mmantsae

2016-01-01

Hematite (α-Fe2O3) is a promising semiconductor as photoanode in solar hydrogen production from photoelectrolysis of water due to its appropriate band gap, low cost and high electrochemical stability in aqueous caustic electrolytes. Operation of such photoanode in a biased photoelectrochemical cell constitutes an anodization with consequent redox reactions at the electrode surface. α-Fe2O3 thin film photoanodes were prepared by simple and inexpensive dip coating method on fluorine doped tin oxide (FTO) glass substrate, annealed in air at 500 °C for 2 h, then electrochemically oxidized (anodized) in 1 M KOH at 500 mV for 1 min in dark and light conditions. Changes in structural properties and morphology of α-Fe2O3 nanoparticles films were investigated by XRD, Raman spectroscopy and a high resolution FE-SEM. The average grain size was observed to increase from 57 nm for pristine samples to 73 and 77 nm for anodized samples in dark and light respectively. Broadening and red shift in Raman spectra in anodized samples may be attributed to lattice expansion upon oxidation. The UV-visible measurements revealed enhanced absorption in the photoanodes after the treatment. The findings suggest that the anodization of the photoelectrode in a biased cell causes not only changes of the molecular structure at the surface, but also changes in the crystallographic structure which can be detected with x-ray diffractometry.

Efficient solar-assisted O2 reduction by a cofacial iron porphyrin dimer integrated to a p-CuBi2O4 photocathode prepared by a simple novel method.

PubMed

Zahran, Zaki N; Mohamed, Eman A; Naruta, Yoshinori; Haleem, Ashraf

2017-10-04

A cofacial iron porphyrin hetero-dimer, Fe2TPFPP-TMP showed high electro-catalytic activity, selectivity, and stability for the O2 reduction to H2O both in homogeneous non-aqueous and heterogeneous neutral aqueous solutions. Moreover, when it is integrated to FTO/p-CuBi2O4 (FTO = fluorine doped tin oxide) photocathode prepared by a simple novel method, a remarkable efficient solar-assisted O2 reduction is achieved in neutral potassium phosphate (KPi) or basic NaOH solutions saturated with O2. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of Post-annealing on the Electrochromic Properties of Layer-by-Layer Arrangement FTO-WO3-Ag-WO3-Ag

NASA Astrophysics Data System (ADS)

Hoseinzadeh, S.; Ghasemiasl, R.; Bahari, A.; Ramezani, A. H.

2018-03-01

In the current study, composites of tungsten trioxide (W03) and silver (Ag) are deposited in a layer-by-layer electrochromic (EC) arrangement onto a fluorine-doped tin oxide coated glass substrate. Tungsten oxide nanoparticles are an n-type semiconductor that can be used as EC cathode material. Nano-sized silver is a metal that can serve as an electron trap center that facilitates charge departure. In this method, the WO3 and Ag nanoparticle powder were deposited by physical vapor deposition onto the glass substrate. The fabricated electrochromic devices (ECD) were post-annealed to examine the effect of temperature on their EC properties. The morphology of the thin film was characterized by scanning electron microscopy and atomic force microscopy. Structural analysis showed that the addition of silver dopant increased the size of the aggregation of the film. The film had an average approximate roughness of about 17.8 nm. The electro-optical properties of the thin film were investigated using cyclic voltammetry and UV-visible spectroscopy to compare the effects of different post-annealing temperatures. The ECD showed that annealing at 200°C provided better conductivity (maximum current of about 90 mA in the oxidation state) and change of transmittance (ΔT = 90% at the continuous switching step) than did the other thin films. The optical band gaps of the thin film showed that it allowed direct transition at 3.85 eV. The EC properties of these combinations of coloration efficiency and response time indicate that the WO3-Ag-WO3-Ag arrangement is a promising candidate for use in such ECDs.

Electrodeposition of CdTe thin film from acetate-based ionic liquid bath

NASA Astrophysics Data System (ADS)

Waldiya, Manmohansingh; Bhagat, Dharini; Mukhopadhyay, Indrajit

2018-05-01

CdTe being a direct band gap semiconductor, is mostly used in photovoltaics. Here we present, the synthesis of CdTe thin film on fluorine doped tin oxide (FTO) substrate potentiostatically using 1-butyl-3-methylimidazolium acetate ([Bmim][Ac]) ionic liquid (IL) bath at 90 °C. Major advantages of using electrodeposition involves process simplicity, large scalability & economic viability. Some of the benefits offered by IL electrolytic bath are low vapour pressure, wide electrochemical window, and good ionic mobility. Cd(CH3COO)2 (anhydrous) and TeO2 were used as the source precursors. The IL electrolytic bath temperature was kept at 90 °C for deposition, owing to the limited solubility of TeO2 in [Bmim][Ac] IL at room temperature. Cathodic electrodeposition was carried out using a three electrode cell setup at a constant potential of -1.20 V vs. platinum (Pt) wire. The CdTe/FTO thin film were annealed in argon (Ar) atmosphere. Optical study of nanostructured CdTe film were done using UV-Vis-IR and Raman spectroscopy. Raman analysis confirms the formation of CdTe having surface optics (SO) mode at 160.6 cm-1 and transverse optics (TO) mode at 140.5 cm-1. Elemental Te peaks at 123, 140.5 and 268 cm-1 were also observed. The optical band gap of Ar annealed CdTe thin film were found to be 1.47 eV (absorbance band edge ˜ 846 nm). The optimization of deposition parameters using acetate-based IL electrolytic bath to get nearly stoichiometric CdTe thin film is currently being explored.

Metal nanostructures with complex surface morphology: The case of supported lumpy Pd and Pt nanoparticles produced by laser processing of metal films

NASA Astrophysics Data System (ADS)

Ruffino, F.; Maugeri, P.; Cacciato, G.; Zimbone, M.; Grimaldi, M. G.

2016-09-01

In this work we report on the formation of lumpy Pd and Pt nanoparticles on fluorine-doped tin oxide/glass (FTO/glass) substrate by a laser-based approach. In general, complex-surface morphology metal nanoparticles can be used in several technological applications exploiting the peculiarities of their physical properties as modulated by nanoscale morphology. For example plasmonic metal nanoparticles presenting a lumpy morphology (i.e. larger particles coated on the surface by smaller particles) can be used in plasmonic solar cell devices providing broadband scattering enhancement over the smooth nanoparticles leading, so, to the increase of the device efficiency. However, the use of plasmonic lumpy nanoparticles remains largely unexplored due to the lack of simply, versatile, low-cost and high-throughput methods for the controllable production of such nanostructures. Starting from these considerations, we report on the observation that nanoscale-thick Pd and Pt films (17.6 and 27.9 nm, 12.1 and 19.5 nm, respectively) deposited on FTO/glass surface irradiated by nanosecond pulsed laser at fluences E in the 0.5-1.5 J/cm2 range, produce Pd and Pt lumpy nanoparticles on the FTO surface. In addition, using scanning electron microscopy analyses, we report on the observation that starting from each metal film of fixed thickness h, the fraction F of lumpy nanoparticles increases with the laser fluence E and saturates at the higher fluences. For each fixed fluence, F was found higher starting from the Pt films (at each starting film thickness h) with respect to the Pd films. For each fixed metal and fluence, F was found to be higher decreasing the starting thickness of the deposited film. To explain the formation of the lumpy Pd and Pt nanoparticles and the behavior of F as a function of E and h both for Pd and Pt, the thermodynamic behavior of the Pd and Pt films and nanoparticles due to the interaction with the nanosecond laser is discussed. In particular, the photothermal vaporization and Coulomb explosion processes of the Pd and Pt nanoparticles are invoked as possible mechanisms for the lumpy nanoparticles formation.

SILAR controlled CdSe nanoparticles sensitized ZnO nanorods photoanode for solar cell application: Electrolyte effect.

PubMed

Nikam, Pratibha R; Baviskar, Prashant K; Majumder, Sutripto; Sali, Jaydeep V; Sankapal, Babasaheb R

2018-08-15

Controlled growth of different sizes of cadmium selenide (CdSe) nanoparticles over well aligned ZnO nanorods have been performed using successive ionic layer adsorption and reaction (SILAR) technique at room temperature (27 °C) in order to form nano heterostructure solar cells. Deposition of compact layer of zinc oxide (ZnO) by SILAR technique on fluorine doped tin oxide (FTO) coated glass substrate followed by growth of vertically aligned ZnO nanorods array using chemical bath deposition (CBD) at low temperature (<100 °C). Different characterization techniques viz. X-ray diffractometer, UV-Vis spectrophotometer, field emission scanning electron microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy have been used to know the structural, optical, morphological and compositional properties of synthesized nano heterostructure. The photovoltaic performance of the cells with variation in SILAR cycles for CdSe and with use of different electrolytes have been recorded as J-V characteristics and the maximum conversion efficiency of 0.63% have been attained with ferro/ferri cyanide electrolyte for 12 cycles CdSe coating over 1-D ZnO nanorods. Copyright © 2018 Elsevier Inc. All rights reserved.

The role of the domain size and titanium dopant in nanocrystalline hematite thin films for water photolysis

DOE PAGES

Yan, Danhua; Tao, Jing; Kisslinger, Kim; ...

2015-10-13

Here we develop a novel technique for preparing high quality Ti-doped hematite thin films for photoelectrochemical (PEC) water splitting, through sputtering deposition of metallic iron films from an iron target embedded with titanium (dopants) pellets, followed by a thermal oxidation step that turns the metal films into doped hematite. It is found that the hematite domain size can be tuned from ~10 nm to over 100 nm by adjusting the sputtering atmosphere from more oxidative to mostly inert. The better crystallinity at a larger domain size ensures excellent PEC water splitting performance, leading to record high photocurrent from pure planarmore » hematite thin films on FTO substrates. Titanium doping further enhances the PEC performance of hematite photoanodes. The photocurrent is improved by 50%, with a titanium dopant concentration as low as 0.5 atom%. As a result, it is also found that the role of the titanium dopant in improving the PEC performance is not apparently related to the films’ electrical conductivity which had been widely believed, but is more likely due to the passivation of surface defects by the titanium dopants.« less

Use of interfacial layers to prolong hole lifetimes in hematite probed by ultrafast transient absorption spectroscopy

NASA Astrophysics Data System (ADS)

Paradzah, Alexander T.; Diale, Mmantsae; Maabong, Kelebogile; Krüger, Tjaart P. J.

2018-04-01

Hematite is a widely investigated material for applications in solar water oxidation due primarily to its small bandgap. However, full realization of the material continues to be hampered by fast electron-hole recombination rates among other weaknesses such as low hole mobility, short hole diffusion length and low conductivity. To address the problem of fast electron-hole recombination, researchers have resorted to growth of nano-structured hematite, doping and use of under-layers. Under-layer materials enhance the photo-current by minimising electron-hole recombination through suppressing of back electron flow from the substrate, such as fluorine-doped tin oxide (FTO), to hematite. We have carried out ultrafast transient absorption spectroscopy on hematite in which Nb2O5 and SnO2 materials were used as interfacial layers to enhance hole lifetimes. The transient absorption data was fit with four different lifetimes ranging from a few hundred femtoseconds to a few nanoseconds. We show that the electron-hole recombination is slower in samples where interfacial layers are used than in pristine hematite. We also develop a model through target analysis to illustrate the effect of under-layers on electron-hole recombination rates in hematite thin films.

Composite WO3/TiO2 nanostructures for high electrochromic activity.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reyes, Karla Rosa; Stephens, Zachary Dan.; Robinson, David B.

2013-05-01

A composite material consisting of TiO2 nanotubes (NTs) with WO3 electrodeposited homogeneously on its surface has been fabricated, detached from its substrate, and attached to a fluorine-doped tin oxide film on glass for application to electrochromic (EC) reactions. A paste of TiO2 made from commercially available TiO2 nanoparticles creates an interface for the TiO2 NT film to attach to the FTO glass, which is conductive and does not cause solution-phase ions in an electrolyte to bind irreversibly with the material. The effect of NT length on the current density and the EC contrast of the material were studied. The ECmore » redox reaction seen in this material is diffusion- limited, having relatively fast reaction rates at the electrode surface. The composite WO3/TiO2 nanostructures showed higher ion storage capacity, better stability, enhanced EC contrast and longer memory time compared with the pure WO3 and TiO2.« less

Experimental Study of Acid Treatment Toward Characterization of Structural, Optical, and Morphological Properties of TiO2-SnO2 Composite Thin Film

NASA Astrophysics Data System (ADS)

Fajar, M. N.; Hidayat, R.; Triwikantoro; Endarko

2018-04-01

The TiO2-SnO2 thin film with single and double-layer structure has successfully synthesized on FTO (Fluorine-doped Tin Oxide) substrate using the screen printing technique. The structural, optical, and morphological properties of the film were investigated by XRD, UV-Vis, and SEM, respectively. The results showed that the single and double-layer structure of TiO2-SnO2 thin film has mixed phase with a strong formation of casseritte phase. The acid treatment effect on TiO2-SnO2 thin film decreases the peak intensity of anatase phase formation and thin film’s absorbance values. The morphological study is also revealed that the single layer TiO2-SnO2 thin film had a more porous nature and decreased particle size distribution after acid treatment, while the double-layer TiO2-SnO2 thin film Eroded due to acid treatment.

The investigation of Ga-doped ZnO as an interlayer for ohmic contact to Cd1-xZnxTe films

NASA Astrophysics Data System (ADS)

Shen, Yibin; Huang, Jian; Gu, Qingmiao; Meng, Hua; Tang, Ke; Shen, Yue; Zhang, Jijun; Wang, Linjun; Lu, Yicheng

2017-12-01

In this work, high quality Cd1-xZnxTe films were prepared on fluorine doped tin oxide (FTO) glass substrates by close-spaced sublimation (CSS) method. A low resistivity sputtered Ga-doped ZnO (GZO) film was used as an interlayer between Au electrodes and Cd1-xZnxTe films try to reduce the contact resistance and contribute to bring about a better Ohmic contact. Circular transmission line model (CTLM) was adopted to investigate the effects of GZO intermediate layer on the contact properties of Au/GZO/Cd1-xZnxTe structure. The results show a low contact resistivity of 0.37 Ω cm2 for Au/GZO contacts on Cd1-xZnxTe films. Cd1-xZnxTe film radiation detectors were also fabricated using Au/GZO contacts and an energy resolution of about 28% was obtained from a 60 KeV 241Am γ-ray source for the first time.

Vertically grown zinc oxide nanorods functionalized with ferric oxide for in vivo and non-enzymatic glucose detection

NASA Astrophysics Data System (ADS)

Marie, Mohammed; Manoharan, Anishkumar; Kuchuk, Andrian; Ang, Simon; Manasreh, M. O.

2018-03-01

An enzyme-free glucose sensor based on vertically grown zinc oxide nanorods (NRs) functionalized with ferric oxide (Fe2O3) is investigated. The well-aligned and high density ZnO NRs were synthesized on an FTO/glass substrate by a sol-gel and hydrothermal growth method. A dip-coating technique was utilized to modify the surface of the as-grown ZnO NRs with Fe2O3. The immobilized surface was coated with a layer of nafion membrane. The fabricated glucose sensor was characterized amperometrically at room temperature using three electrodes stationed in the phosphate buffer solution, where ZnO NRs/Fe2O3/nafion membrane was the sensing or working electrode, and platinum plate and silver/silver chloride were used as the counter and reference electrodes, respectively. The proposed non-enzymatic and modified glucose sensor exhibited a high sensitivity in the order of 0.052 μA cm-2 (mg/dL)-1, a lower detection limit of around 0.95 mmol L-1, a sharp and fast response time of ˜1 s, and a linear response to changes in glucose concentrations from 100-400 mg dL-1. The linear amperometric response of the sensor covers the physiological and clinical interest of glucose levels for diabetic patients. The device continues to function accurately after multiple measurements with a good reproducibility. The proposed glucose sensor is expected to be used clinically for in vivo monitoring of glucose.

Nanoscale TiO2 and Fe2O3 Architectures for Solar Energy Conversion Schemes

NASA Astrophysics Data System (ADS)

Sedach, Pavel Anatolyvich

The direct conversion of sunlight into more useable forms of energy has the potential of alleviating the environmental and social problems associated with a dependence on fossil fuels. If solar energy is to be utilized en-masse, however, it must be inexpensive and widely available. In this vein, the focus of this thesis is on nanostructured materials relevant to solar energy conversion and storage. Specifically, this thesis describes the ambient sol-gel synthesis of titanium dioxide (Ti02) nanowires designed for enhanced charge-transfer in solar collection devices, and the synthesis of novel disordered metal-oxide (MOx) catalysts for water oxidation. The introductory chapter of this thesis gives an overview of the various approaches to solar energy conversion. Sol---gel reaction conditions that enable the growth of one-dimensional (1-D) anatase TiO2 nanostructures from fluorine-doped tin oxide (FTO) for photovoltaics (PVs) are described in the second chapter. The generation of these linear nanostructures in the absence of an external bias or template is achieved by using facile experimental conditions (e.g., acetic acid (HOAc) and titanium isopropoxide (Ti(OiPr)4) in anhydrous heptane). The procedure was developed by functionalizing base-treated substrates with Ti-oxide nucleation sites that serve as a foundation for the growth of linear Ti-oxide macromolecules, which upon calcination, render uniform films of randomly oriented anatase TiO2 nanowires. A systematic evaluation of how reaction conditions (e.g., solvent volume, stoichiometry of reagents, substrate base treatment) affect the generation of these TiO 2 films is presented. A photo-organic MO. deposition route (i.e., photochemical metal-organic deposition (PMOD)) used to deposit thin-films of amorphous iron oxide (a-Fe2O3) for water oxidation catalysis is detailed in third chapter. It is shown that the irradiation of a spin-coated metal-organic film produces a film of non-crystalline a-Fe203. It is shown that annealing at various temperatures produces a-Fe 2O3 films with variable electronic properties and catalytic activities in the context of water oxidation. The study revealed that a-Fe2O3 are superior water oxidation catalysts (WOCs) relative to crystalline forms produced by high temperature annealing of the thin-films. This research has important implications in the conversion of sunlight into electricity, and then into hydrogen fuels.

A two-layer structured PbI2 thin film for efficient planar perovskite solar cells.

PubMed

Ying, Chao; Shi, Chengwu; Wu, Ni; Zhang, Jincheng; Wang, Mao

2015-07-28

In this paper, a two-layer structured PbI2 thin film was constructed by the spin-coating procedure using a 0.80 M PbI2 solution in DMF and subsequent close-spaced vacuum thermal evaporation using PbI2 powder as a source. The bottom PbI2 thin film was compact with a sheet-like appearance, parallel to the FTO substrate, and can be easily converted to a compact perovskite thin film to suppress the charge recombination of the electrons of the TiO2 conduction band and the holes of the spiro-OMeTAD valence band. The top PbI2 thin film was porous with nano-sheet arrays, perpendicular to the FTO substrate, and can be easily converted to a porous perovskite thin film to improve the hole migration from the perovskite to spiro-OMeTAD and the charge separation at the perovskite/spiro-OMeTAD interface. The planar perovskite solar cells based on the two-layer structured PbI2 thin film exhibited a photoelectric conversion efficiency of 11.64%, along with an open-circuit voltage of 0.90 V, a short-circuit photocurrent density of 19.29 mA cm(-2) and a fill factor of 0.67.

Preparation of Platinum (Pt) Counter Electrode Coated by Electrochemical Technique at High Temperature for Dye-sensitized Solar Cell (DSSC) Application

NASA Astrophysics Data System (ADS)

Ponken, Tanachai; Tagsin, Kamonlapron; Suwannakhun, Chuleerat; Luecha, Jakkrit; Choawunklang, Wijit

2017-09-01

Pt counter electrode was coated by electrochemical method. Electrolyte solution was synthesized by platinum (IV) choloride (PtCl4) powder dissolved in hydrochloric acid solution. Pt films were deposited on the FTO substrate. Deposition time of 10, 30 and 60 minutes, the coating current of 5, 10, 15 and 20 mA and electrolyte solution temperatures for Pt layer synthesis of 25, 30 and 40°C were varied. Surface morphology and optical properties was analyzed by digital microscopic and UV-vis spectrophotometer. Pt films exhibit uniform surface area highly for all the conditions of coating current in the deposition time of 30 and 40 minutes at 40°C. Transmittance values of Pt films deposited on FTO substrate has approximately of 5 to 50 % show that occur high reflection corresponding to dye molecule absorption increases. DSSC device was fabricated from the TiO2 standard and immersed in dye N719 for 24 hours. Efficiency was measured by solar simulator. Efficiency value obtains as high as 5.91 % for the coating current, deposition time and solution temperature of 15 mA, 30 minutes and 40°C. Summary, influence of temperature effects efficiency increasing. Pt counter electrode can be prepared easily and the suitable usefully for DSSC.

ZnO-Assisted Growth of CH3NH3PbI3- xCl x Film and Efficient Planar Perovskite Solar Cells with a TiO2/ZnO/C60 Electron Transport Trilayer.

PubMed

Xu, Jia; Fang, Mingde; Chen, Jing; Zhang, Bing; Yao, Jianxi; Dai, Songyuan

2018-06-06

Appropriate electron transport layers (ETL) are essential in perovskite solar cells (PSCs) with high power conversion efficiency (PCE). Herein, a TiO 2 /ZnO/C 60 trilayer fabricated on a transparent fluorine-doped tin oxide (FTO) glass substrate is used as a compound ETL in planar PSCs. The trilayer shows positive effects on both perovskite synthesis and device performance. The ZnO layer assists growth of CH 3 NH 3 PbI 3- x Cl x ( x ≈ 0) annealed at a lower temperature and with a shorter time, which is due to a more rapid and easier decomposition of the intermediate CH 3 NH 3 PbCl 3 phase in the growth of CH 3 NH 3 PbI 3- x Cl x . All three materials in the trilayer are important for obtaining PSCs with a high PCE. ZnO is critical for enhancing the open circuit voltage by ensuring proper energy alignment with the TiO 2 and C 60 layers. C 60 enhances carrier extraction from the CH 3 NH 3 PbI 3- x Cl x layer. TiO 2 eliminates charge recombination at the FTO surface and ensures efficient electron collection. The best-performing PSC based on the TiO 2 /ZnO/C 60 electron transport trilayer features a PCE of 18.63% with a fill factor of 79.12%. These findings help develop an understanding of the effects of ZnO-containing ETLs on perovskite film synthesis and show promise for the future development of high-performance PSCs with compound ETLs.

Influence of metal work function and incorporation of Sr atom on WO3 thin films for MIS and MIM structured SBDs

NASA Astrophysics Data System (ADS)

Marnadu, R.; Chandrasekaran, J.; Raja, M.; Balaji, M.; Maruthamuthu, S.; Balraju, P.

2018-07-01

In this work, two different structure of Cu/Sr-WO3/p-Si metal-insulator-semiconductor (MIS) and Cu/Sr-WO3/FTO metal-insulator-metal (MIM) Schottky barrier diodes (SBDs) fabricated with an insulating layer of pure tungsten trioxide (WO3) and Sr-WO3 thin films have been reported. The Sr-WO3 layer was coated separately, with different concentrations (0, 4, 8 and 12 wt %) of strontium (Sr) via jet nebulizer spray pyrolysis technique (JNSP) on the p-type silica wafer (p-Si) and fluorine doped tin oxide (FTO) substrates which are been optimized at 400 °C. The XRD analysis reveals the multiphase crystalline structures for 12 wt % of Sr-WO3 film with higher average crystallite size. FE-SEM images show the randomly oriented sub-microsized slab and seashell like structures. Higher surface roughness with improved grain size for 12 wt % of Sr-WO3 film. The presence of W, O and Sr atoms was confirmed by EDX spectra. In optical studies, Maximum absorption with minimum optical band gap was observed for 12 wt % of Sr-WO3 composite film. There was a linear increase in the electrical conductivity of the films with higher wt. % of Sr. Evidently the activation energy decreased with Sr concentration which is in accordance with the bandgap values. The fitting results of the measured I-V, reveal that MIS (SBDs) under illumination condition have minimum ideality factor (n = 2.39) and maximum barrier height (Φb = 0.57) values for higher concentration (12 wt %) of Sr film compared to MIM SBDs.

Dual-step synthesis of 3-dimensional niobium oxide - Zinc oxide

NASA Astrophysics Data System (ADS)

Rani, Rozina Abdul; Zoolfakar, Ahmad Sabirin; Rusop, M.

2018-05-01

A facile fabrication process for constructing 3-dimensional (3D) structure of Niobium oxide - Zinc oxide (Nb2O5-ZnO) consisting of branched ZnO microrods on top of nanoporous Nb2O5 films was developed based on dual-step synthesis approach. The preliminary procedure was anodization of sputtered niobium metal on Fluorine doped Tin Oxide (FTO) to produce nanoporous Nb2O5, and continued with the growth of branched microrods of ZnO by hydrothermal process. This approach offers insight knowledge on the development of novel 3D metal oxide films via dual-step synthesis process, which might potentially use for multi-functional applications ranging from sensing to photoconversion.

Loss of FTO antagonises Wnt signaling and leads to developmental defects associated with ciliopathies.

PubMed

Osborn, Daniel P S; Roccasecca, Rosa Maria; McMurray, Fiona; Hernandez-Hernandez, Victor; Mukherjee, Sriparna; Barroso, Inês; Stemple, Derek; Cox, Roger; Beales, Philip L; Christou-Savina, Sonia

2014-01-01

Common intronic variants in the Human fat mass and obesity-associated gene (FTO) are found to be associated with an increased risk of obesity. Overexpression of FTO correlates with increased food intake and obesity, whilst loss-of-function results in lethality and severe developmental defects. Despite intense scientific discussions around the role of FTO in energy metabolism, the function of FTO during development remains undefined. Here, we show that loss of Fto leads to developmental defects such as growth retardation, craniofacial dysmorphism and aberrant neural crest cells migration in Zebrafish. We find that the important developmental pathway, Wnt, is compromised in the absence of FTO, both in vivo (zebrafish) and in vitro (Fto(-/-) MEFs and HEK293T). Canonical Wnt signalling is down regulated by abrogated β-Catenin translocation to the nucleus whilst non-canonical Wnt/Ca(2+) pathway is activated via its key signal mediators CaMKII and PKCδ. Moreover, we demonstrate that loss of Fto results in short, absent or disorganised cilia leading to situs inversus, renal cystogenesis, neural crest cell defects and microcephaly in Zebrafish. Congruently, Fto knockout mice display aberrant tissue specific cilia. These data identify FTO as a protein-regulator of the balanced activation between canonical and non-canonical branches of the Wnt pathway. Furthermore, we present the first evidence that FTO plays a role in development and cilia formation/function.

Fto colocalizes with a satiety mediator oxytocin in the brain and upregulates oxytocin gene expression

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olszewski, Pawel K., E-mail: olsze005@umn.edu; Minnesota Obesity Center, Saint Paul, MN 55108; Fredriksson, Robert

2011-05-13

Highlights: {yields} The majority of neurons synthesizing a satiety mediator, oxytocin, coexpress Fto. {yields} The level of colocalization is similar in the male and female brain. {yields} Fto overexpression in hypothalamic neurons increases oxytocin mRNA levels by 50%. {yields} Oxytocin does not affect Fto expression through negative feedback mechanisms. -- Abstract: Single nucleotide polymorphisms in the fat mass and obesity-associated (FTO) gene have been associated with obesity in humans. Alterations in Fto expression in transgenic animals affect body weight, energy expenditure and food intake. Fto, a nuclear protein and proposed transcription co-factor, has been speculated to affect energy balance throughmore » a functional relationship with specific genes encoding feeding-related peptides. Herein, we employed double immunohistochemistry and showed that the majority of neurons synthesizing a satiety mediator, oxytocin, coexpress Fto in the brain of male and female mice. We then overexpressed Fto in a murine hypothalamic cell line and, using qPCR, detected a 50% increase in the level of oxytocin mRNA. Expression levels of several other feeding-related genes, including neuropeptide Y (NPY) and Agouti-related protein (AgRP), were unaffected by the FTO transfection. Addition of 10 and 100 nmol oxytocin to the cell culture medium did not affect Fto expression in hypothalamic cells. We conclude that Fto, a proposed transcription co-factor, influences expression of the gene encoding a satiety mediator, oxytocin.« less

Identification of Fat Mass and Obesity Associated (FTO) Protein Expression in Cardiomyocytes: Regulation by Leptin and Its Contribution to Leptin-Induced Hypertrophy

PubMed Central

Gan, Xiaohong Tracey; Zhao, Ganjian; Huang, Cathy X.; Rowe, Adrianna C.; Purdham, Daniel M.; Karmazyn, Morris

2013-01-01

The recently-identified fat mass and obesity-associated (FTO) protein is associated with various physiological functions including energy and body weight regulation. Ubiquitously expressed, FTO was identified in heart homogenates although its function is unknown. We studied whether FTO is specifically expressed within the cardiac myocyte and its potential role pertaining to the hypertrophic effect of the adipokine leptin. Most experiments were performed using cultured neonatal rat cardiomyocytes which showed nuclei-specific FTO expression. Leptin significantly increased FTO expression which was associated with myocyte hypertrophy although both events were abrogated by FTO knockdown with siRNA. Administration of a leptin receptor antibody to either normal or obese rats significant reduced myocardial FTO protein expression. Responses in cardiomyocytes were accompanied by JAK2/STAT3 activation whereas JAK2/STAT3 inhibition abolished these effects. Expression of the cut-like homeobox 1(CUX1) transcriptional factor was significantly increased by leptin although this was restricted to the cathepsin L-dependent, proteolytically-derived shorter p110CUX1 isoform whereas the longer p200CUX1 protein was not significantly affected. Cathepsin L expression and activity were both significantly increased by leptin whereas a cathepsin L peptide inhibitor or siRNA specific for CUX1 completely prevented the leptin-induced increase in FTO expression. The cathepsin L peptide inhibitor or siRNA-induced knockdown of either CUX1 or FTO abrogated the hypertrophic response to leptin. Two other pro-hypertrophic factors, endothelin-1 or angiotensin II had no effect on FTO expression and FTO knockdown did not alter the hypertrophic response to either agent. This study demonstrates leptin-induced FTO upregulation in cardiomyocytes via JAK2/STAT3- dependent CUX1 upregulation and suggests an FTO regulatory function of leptin. It also demonstrates for the first time a functional role of FTO in the cardiomyocyte. PMID:24019958

Identification of fat mass and obesity associated (FTO) protein expression in cardiomyocytes: regulation by leptin and its contribution to leptin-induced hypertrophy.

PubMed

Gan, Xiaohong Tracey; Zhao, Ganjian; Huang, Cathy X; Rowe, Adrianna C; Purdham, Daniel M; Karmazyn, Morris

2013-01-01

The recently-identified fat mass and obesity-associated (FTO) protein is associated with various physiological functions including energy and body weight regulation. Ubiquitously expressed, FTO was identified in heart homogenates although its function is unknown. We studied whether FTO is specifically expressed within the cardiac myocyte and its potential role pertaining to the hypertrophic effect of the adipokine leptin. Most experiments were performed using cultured neonatal rat cardiomyocytes which showed nuclei-specific FTO expression. Leptin significantly increased FTO expression which was associated with myocyte hypertrophy although both events were abrogated by FTO knockdown with siRNA. Administration of a leptin receptor antibody to either normal or obese rats significant reduced myocardial FTO protein expression. Responses in cardiomyocytes were accompanied by JAK2/STAT3 activation whereas JAK2/STAT3 inhibition abolished these effects. Expression of the cut-like homeobox 1(CUX1) transcriptional factor was significantly increased by leptin although this was restricted to the cathepsin L-dependent, proteolytically-derived shorter p110CUX1 isoform whereas the longer p200CUX1 protein was not significantly affected. Cathepsin L expression and activity were both significantly increased by leptin whereas a cathepsin L peptide inhibitor or siRNA specific for CUX1 completely prevented the leptin-induced increase in FTO expression. The cathepsin L peptide inhibitor or siRNA-induced knockdown of either CUX1 or FTO abrogated the hypertrophic response to leptin. Two other pro-hypertrophic factors, endothelin-1 or angiotensin II had no effect on FTO expression and FTO knockdown did not alter the hypertrophic response to either agent. This study demonstrates leptin-induced FTO upregulation in cardiomyocytes via JAK2/STAT3- dependent CUX1 upregulation and suggests an FTO regulatory function of leptin. It also demonstrates for the first time a functional role of FTO in the cardiomyocyte.

A genosensor for detection of consensus DNA sequence of Dengue virus using ZnO/Pt-Pd nanocomposites.

PubMed

Singhal, Chaitali; Pundir, C S; Narang, Jagriti

2017-11-15

An electrochemical genosensor based on Zinc oxide/platinum-palladium (ZnO/Pt-Pd) modified fluorine doped tin oxide (FTO) glass plate was fabricated for detection of consensus DNA sequence of Dengue virus (DENV) using methylene blue (MB) as an intercalating agent. To achieve it, probe DNA (PDNA) was immobilized on the surface of ZnO/Pt-Pd nanocomposites modified FTO electrode. The synthesized nano-composites were characterized by high resolution transmission electron microscopy (HRTEM), energy dispersive X-ray analysis (EDX), atomic force microscopy (AFM), scanning electron microscopy (SEM), UV-Vis spectroscopy, X-ray diffraction (XRD) analysis and Fourier transform infra-red (FTIR) spectroscopy. This PDNA modified electrode (PDNA/ZnO/Pt-Pd/FTO) served as a signal amplification platform for the detection of the target hybridized DNA (TDNA). The hybridization between PDNA and TDNA was detected by reduction in current, generated by interaction of anionic mediator, i.e., methylene blue (MB) with free guanine (3'G) of ssDNA. The sensor showed a dynamic linear range of 1 × 10 -6 M to 100 × 10 -6 M with LOD as 4.3 × 10 -5 M and LOQ as 9.5 × 10 -5 M. Till date, majorly serotype specific biosensors for dengue detection have been developed. The genosensor reported here eliminates the possibility of false result as in case of serotype specific DNA sensor. This is the report where conserved sequences present in all the serotypes of Dengue virus has been employed for fabrication of a genosensor. Copyright © 2017 Elsevier B.V. All rights reserved.

Catalytic, conductive, and transparent platinum nanofiber webs for FTO-free dye-sensitized solar cells.

PubMed

Kim, Jongwook; Kang, Jonghyun; Jeong, Uiyoung; Kim, Heesuk; Lee, Hyunjung

2013-04-24

We report a multifunctional platinium nanofiber (PtNF) web that can act as a catalyst layer in dye-sensitized solar cell (DSSC) to simultaneously function as a transparent counter electrode (CE), i.e., without the presence of an indium-doped tin oxide (ITO) or fluorine-doped tin oxide (FTO) glass. This PtNF web can be easily produced by electrospinning, which is highly cost-effective and suitable for large-area industrial-scale production. Electrospun PtNFs are straight and have a length of a few micrometers, with a common diameter of 40-70 nm. Each nanofiber is composed of compact, crystalline Pt grains and they are well-fused and highly interconnected, which should be helpful to provide an efficient conductive network for free electron transport and a large surface area for electrocatalytic behavior. A PtNF web is served as a counter electrode in DSSC and the photovoltaic performance increases up to a power efficiency of 6.0%. It reaches up to 83% of that in a conventional DSSC using a Pt-coated FTO glass as a counter electrode. Newly designed DSSCs containing PtNF webs display highly stable photoelectric conversion efficiencies, and excellent catalytic, conductive, and transparent properties, as well as long-term stability. Also, while the DSSC function is retained, the fabrication cost is reduced by eliminating the transparent conducting layer on the counter electrode. The presented method of fabricating DSSCs based on a PtNF web can be extended to other electrocatalytic optoelectronic devices that combine superior catalytic activity with high conductivity and transparency.

3D FTO/FTO-Nanocrystal/TiO2 Composite Inverse Opal Photoanode for Efficient Photoelectrochemical Water Splitting.

PubMed

Wang, Zhiwei; Li, Xianglin; Ling, Han; Tan, Chiew Kei; Yeo, Loo Pin; Grimsdale, Andrew Clive; Tok, Alfred Iing Yoong

2018-05-01

A 3D fluorine-doped SnO 2 (FTO)/FTO-nanocrystal (NC)/TiO 2 inverse opal (IO) structure is designed and fabricated as a new "host and guest" type of composite photoanode for efficient photoelectrochemical (PEC) water splitting. In this novel photoanode design, the highly conductive and porous FTO/FTO-NC IO acts as the "host" skeleton, which provides direct pathways for faster electron transport, while the conformally coated TiO 2 layer acts as the "guest" absorber layer. The unique composite IO structure is fabricated through self-assembly of colloidal spheres template, a hydrothermal method and atomic layer deposition (ALD). Owing to its large surface area and efficient charge collection, the FTO/FTO-NC/TiO 2 composite IO photoanode shows excellent photocatalytic properties for PEC water splitting. With optimized dimensions of the SnO 2 nanocrystals and the thickness of the ALD TiO 2 absorber layers, the 3D FTO/FTO-NC/TiO 2 composite IO photoanode yields a photocurrent density of 1.0 mA cm -2 at 1.23 V versus reversible hydrogen electrode (RHE) under AM 1.5 illumination, which is four times higher than that of the FTO/TiO 2 IO reference photoanode. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Organic Light-Emitting Diodes with a Perylene Interlayer Between the Electrode-Organic Interface

NASA Astrophysics Data System (ADS)

Saikia, Dhrubajyoti; Sarma, Ranjit

2018-01-01

The performance of an organic light-emitting diode (OLED) with a vacuum-deposited perylene layer over a fluorine-doped tin oxide (FTO) surface is reported. To investigate the effect of the perylene layer on OLED performance, different thicknesses of perylene are deposited on the FTO surface and their current density-voltages (J-V), luminance-voltages (L-V) and device efficiency characteristics at their respective thickness are studied. Further analysis is carried out with an UV-visible light double-beam spectrophotometer unit, a four-probe resistivity unit and a field emission scanning electron microscope set up to study the optical transmittance, sheet resistance and surface morphology of the bilayer anode film. We used N,N'-bis(3-methyl phenyl)- N,N'(phenyl)-benzidine (TPD) as the hole transport layer, Tris(8-hydroxyquinolinato)aluminum (Alq3) as a light-emitting layer and lithium fluoride as an electron injection layer. The luminance efficiency of an OLED structure with a 9-nm-thick perylene interlayer is increased by 2.08 times that of the single-layer FTO anode OLED. The maximum value of current efficiency is found to be 5.25 cd/A.

Experimental study on structural, optoelectronic and room temperature sensing performance of Nickel doped ZnO based ethanol sensors

NASA Astrophysics Data System (ADS)

Sudha, M.; Radha, S.; Kirubaveni, S.; Kiruthika, R.; Govindaraj, R.; Santhosh, N.

2018-04-01

Nano crystalline undoped (1Z) Zinc Oxide (ZnO) and 5, 10 and 15 Wt. % (1ZN, 2ZN and 3ZN) of Nickel doped ZnO based sensors were fabricated using the hydrothermal approach on Fluorine doped Tin Oxide (FTO) glass substrates. X-ray diffraction (XRD) analysis proved the hexagonal Wurtzite structure of ZnO. Parametric variations in terms of dislocation density, bond length, lattice parameters and micro strain with respect to dopant concentration were analysed. The prominent variations in the crystallite size, optical band gap and Photoluminescence peak ratio of devices fabricated was observed. The Field Emission Scanning Electron Microscope (FESEM) images showed a change in diameter and density of the nanorods. The effect of the operating temperature, concentration of ethanol and the different doping levels of sensitivity, response and recovery time were investigated. It was inferred that 376% of sensitivity with a very quick response and recovery time of <5 s and 10 s respectively at 150 °C of 3ZN sensor has better performance compared to other three sensors. Also 3ZN sensor showed improved sensitivity of 114%, even at room temperature with response and recovery time of 35 s and 45 s respectively.

An electrochemical sensor for detection of neurotransmitter-acetylcholine using metal nanoparticles, 2D material and conducting polymer modified electrode.

PubMed

Chauhan, Nidhi; Chawla, Sheetal; Pundir, C S; Jain, Utkarsh

2017-03-15

An essential biological sensor for acetylcholine (ACh) detection is constructed by immobilizing enzymes, acetylcholinesterase (AChE) and choline oxidase (ChO), on the surface of iron oxide nanoparticles (Fe 2 O 3 NPs), poly(3,4-ethylenedioxythiophene) (PEDOT)-reduced graphene oxide (rGO) nanocomposite modified fluorine doped tin oxide (FTO). The qualitative and quantitative measurements of nanocomposites properties were accomplished by scanning electron microscope (SEM), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). This prepared biological sensor delineated a wide linear range of 4.0nM to 800μM with a response time less than 4s and detection limit (based on S/N ratio) of 4.0nM. The sensor showed perfect sensitivity, excessive selectivity and stability for longer period of time during storage. Besides its very high-sensitivity, the biosensor has displayed a low detection limit which is reported for the first time in comparison to previously reported ACh sensors. By fabricating Fe 2 O 3 NPs/rGO/PEDOT modified FTO electrode for determining ACh level in serum samples, the applicability of biosensor has increased immensely as the detection of the level neurotransmitter is first priority for patients suffering from memory loss or Alzheimer's disease (AD). Copyright © 2016 Elsevier B.V. All rights reserved.

Enhanced Photoelectrochemical Behavior of H-TiO2 Nanorods Hydrogenated by Controlled and Local Rapid Thermal Annealing

NASA Astrophysics Data System (ADS)

Wang, Xiaodan; Estradé, Sonia; Lin, Yuanjing; Yu, Feng; Lopez-Conesa, Lluis; Zhou, Hao; Gurram, Sanjeev Kumar; Peiró, Francesca; Fan, Zhiyong; Shen, Hao; Schaefer, Lothar; Braeuer, Guenter; Waag, Andreas

2017-05-01

Recently, colored H-doped TiO2 (H-TiO2) has demonstrated enhanced photoelectrochemical (PEC) performance due to its unique crystalline core—disordered shell nanostructures and consequent enhanced conduction behaviors between the core-shell homo-interfaces. Although various hydrogenation approaches to obtain H-TiO2 have been developed, such as high temperature hydrogen furnace tube annealing, high pressure hydrogen annealing, hydrogen-plasma assisted reaction, aluminum reduction and electrochemical reduction etc., there is still a lack of a hydrogenation approach in a controlled manner where all processing parameters (temperature, time and hydrogen flux) were precisely controlled in order to improve the PEC performance of H-TiO2 and understand the physical insight of enhanced PEC performance. Here, we report for the first time a controlled and local rapid thermal annealing (RTA) approach to prepare hydrogenated core-shell H-TiO2 nanorods grown on F:SnO2 (FTO) substrate in order to address the degradation issue of FTO in the typical TiO2 nanorods/FTO system observed in the conventional non-RTA treated approaches. Without the FTO degradation in the RTA approach, we systematically studied the intrinsic relationship between the annealing temperature, structural, optical, and photoelectrochemical properties in order to understand the role of the disordered shell on the improved photoelectrochemical behavior of H-TiO2 nanorods. Our investigation shows that the improvement of PEC performance could be attributed to (i) band gap narrowing from 3.0 to 2.9 eV; (ii) improved optical absorption in the visible range induced by the three-dimensional (3D) morphology and rough surface of the disordered shell; (iii) increased proper donor density; (iv) enhanced electron-hole separation and injection efficiency due to the formation of disordered shell after hydrogenation. The RTA approach developed here can be used as a suitable hydrogenation process for TiO2 nanorods/FTO system for important applications such as photocatalysis, hydrogen generation from water splitting and solar energy conversion.

Enhanced Photoelectrochemical Behavior of H-TiO2 Nanorods Hydrogenated by Controlled and Local Rapid Thermal Annealing.

PubMed

Wang, Xiaodan; Estradé, Sonia; Lin, Yuanjing; Yu, Feng; Lopez-Conesa, Lluis; Zhou, Hao; Gurram, Sanjeev Kumar; Peiró, Francesca; Fan, Zhiyong; Shen, Hao; Schaefer, Lothar; Braeuer, Guenter; Waag, Andreas

2017-12-01

Recently, colored H-doped TiO 2 (H-TiO 2 ) has demonstrated enhanced photoelectrochemical (PEC) performance due to its unique crystalline core-disordered shell nanostructures and consequent enhanced conduction behaviors between the core-shell homo-interfaces. Although various hydrogenation approaches to obtain H-TiO 2 have been developed, such as high temperature hydrogen furnace tube annealing, high pressure hydrogen annealing, hydrogen-plasma assisted reaction, aluminum reduction and electrochemical reduction etc., there is still a lack of a hydrogenation approach in a controlled manner where all processing parameters (temperature, time and hydrogen flux) were precisely controlled in order to improve the PEC performance of H-TiO 2 and understand the physical insight of enhanced PEC performance. Here, we report for the first time a controlled and local rapid thermal annealing (RTA) approach to prepare hydrogenated core-shell H-TiO 2 nanorods grown on F:SnO 2 (FTO) substrate in order to address the degradation issue of FTO in the typical TiO 2 nanorods/FTO system observed in the conventional non-RTA treated approaches. Without the FTO degradation in the RTA approach, we systematically studied the intrinsic relationship between the annealing temperature, structural, optical, and photoelectrochemical properties in order to understand the role of the disordered shell on the improved photoelectrochemical behavior of H-TiO 2 nanorods. Our investigation shows that the improvement of PEC performance could be attributed to (i) band gap narrowing from 3.0 to 2.9 eV; (ii) improved optical absorption in the visible range induced by the three-dimensional (3D) morphology and rough surface of the disordered shell; (iii) increased proper donor density; (iv) enhanced electron-hole separation and injection efficiency due to the formation of disordered shell after hydrogenation. The RTA approach developed here can be used as a suitable hydrogenation process for TiO 2 nanorods/FTO system for important applications such as photocatalysis, hydrogen generation from water splitting and solar energy conversion.

The beneficial effects of betaine on dysfunctional adipose tissue and N6-methyladenosine mRNA methylation requires the AMP-activated protein kinase α1 subunit.

PubMed

Zhou, Xihong; Chen, Jingqing; Chen, Jin; Wu, Weiche; Wang, Xinxia; Wang, Yizhen

2015-12-01

The current study was conducted to determine whether betaine could improve fatty acid oxidation, mitochondrial function and N6-methyladenosine (m(6)A) mRNA methylation in adipose tissue in high-fat-induced mice and how AMP-activated protein kinase α1 subunit (AMPKα1) was involved. AMPKα1 knockout mice and wild-type mice were fed either a low-fat diet, high-fat diet or high-fat diet supplemented with betaine in the drinking water for 8weeks. Our results showed that mitochondrial genes (PGC1α) and β-oxidation-related genes (CPT1a) at protein level were increased in wild-type mice supplemented with betaine when compared with those in mice with high-fat diet. Betaine also decreased FTO expression and improved m(6)A methylation in adipose tissue of wild-type mice with high-fat diet. However, betaine failed to exert the abovementioned effects in AMPKα1 knockout mice. In adipocytes isolated from mice with high-fat diet, betaine treatment increased lipolysis and lipid oxidation. Moreover, betaine decreased FTO expression and increased m(6)A methylation. However, while AMPKα1 was knockdown, no remarkable changes in adipocytes were observed under betaine treatment. Our results indicated that betaine supplementation rectified mRNA hypomethylation and high FTO expression induced by high-fat diet, which may contribute to its beneficial effects on impaired adipose tissue function. Our results suggested that the AMPKα1 subunit is required for the beneficial effects of betaine on dysfunctional adipose tissue and m(6)A methylation. These results may provide the foundation for a mechanism that links m(6)A methylation status in RNA, AMPKα1 phosphorylation and dysfunctional adipose tissue induced by high-fat diet. Copyright © 2015 Elsevier Inc. All rights reserved.

Fundamental Factors Impacting the Stability of Phosphonate-Derivatized Ruthenium Polypyridyl Sensitizers Adsorbed on Metal Oxide Surfaces.

PubMed

Raber, McKenzie; Brady, Matthew David; Troian-Gautier, Ludovic; Dickenson, John; Marquard, Seth L; Hyde, Jacob; Lopez, Santiago; Meyer, Gerald J; Meyer, Thomas J; Harrison, Daniel P

2018-06-08

A series of 18 ruthenium(II) polypyridyl complexes were synthesized and evaluated under electrochemically oxidative conditions, which generates the Ru(III) oxidation state and mimics the harsh conditions experienced during the kinetically-limited regime that can occur in dye-sensitized solar cells (DSSCs) and dye-sensitized photoelectrosynthesis cells (DSPECs), to further develop fundamental insights into the factors governing molecular sensitizer surface stability in aqueous 0.1 M HClO4 (aq). Both desorption and oxidatively induced ligand substitution were observed on planar fluorine doped tin oxide, FTO, electrodes, with a dependence on the E1/2 Ru(III/II) redox potential dictating the comparative ratios of the processes. Complexes such as RuP4OMe (E1/2 = 0.91 vs Ag/AgCl) displayed virtually only desorption, while complexes such as RuPbpz (E1/2 > 1.62 V vs Ag/AgCl) displayed only chemical decomposition. Comparing isomers of 4,4'- and 5,5-disubstituted-2,2'-bipyridine ancillary polypyridyl ligands, a dramatic increase in the rate of desorption of the Ru(III) complexes was observed for the 5,5'-ligands. Nanoscopic indium doped tin oxide thin films, nanoITO, were also sensitized and analyzed with cyclic voltammetry, UV-Vis absorption spectroscopy, and XPS, allowing for further distinction of desorption versus ligand substitution processes. Desorption loss to bulk solution associated with the planar surface of FTO is essentially non-existent on nanoITO, where both desorption and ligand substitution are shut down with RuP4OMe. These results revealed that minimizing time spent in the oxidized form, incorporating electron donating groups, maximizing hydrophobicity, and minimizing molecular bulk near the adsorbed ligand are critical to optimizing the performance of ruthenium(II) polypyridyl complexes in dye-sensitized solar cell devices.

Milk: an epigenetic amplifier of FTO-mediated transcription? Implications for Western diseases.

PubMed

Melnik, Bodo C

2015-12-21

Single-nucleotide polymorphisms within intron 1 of the FTO (fat mass and obesity-associated) gene are associated with enhanced FTO expression, increased body weight, obesity and type 2 diabetes mellitus (T2DM). The N (6) -methyladenosine (m(6)A) demethylase FTO plays a pivotal regulatory role for postnatal growth and energy expenditure. The purpose of this review is to provide translational evidence that links milk signaling with FTO-activated transcription of the milk recipient. FTO-dependent demethylation of m(6)A regulates mRNA splicing required for adipogenesis, increases the stability of mRNAs, and affects microRNA (miRNA) expression and miRNA biosynthesis. FTO senses branched-chain amino acids (BCAAs) and activates the nutrient sensitive kinase mechanistic target of rapamycin complex 1 (mTORC1), which plays a key role in translation. Milk provides abundant BCAAs and glutamine, critical components increasing FTO expression. CpG hypomethylation in the first intron of FTO has recently been associated with T2DM. CpG methylation is generally associated with gene silencing. In contrast, CpG demethylation generally increases transcription. DNA de novo methylation of CpG sites is facilitated by DNA methyltransferases (DNMT) 3A and 3B, whereas DNA maintenance methylation is controlled by DNMT1. MiRNA-29s target all DNMTs and thus reduce DNA CpG methylation. Cow´s milk provides substantial amounts of exosomal miRNA-29s that reach the systemic circulation and target mRNAs of the milk recipient. Via DNMT suppression, milk exosomal miRNA-29s may reduce the magnitude of FTO methylation, thereby epigenetically increasing FTO expression in the milk consumer. High lactation performance with increased milk yield has recently been associated with excessive miRNA-29 expression of dairy cow mammary epithelial cells (DCMECs). Notably, the galactopoietic hormone prolactin upregulates the transcription factor STAT3, which induces miRNA-29 expression. In a retrovirus-like manner milk exosomes may transfer DCMEC-derived miRNA-29s and bovine FTO mRNA to the milk consumer amplifying FTO expression. There is compelling evidence that obesity, T2DM, prostate and breast cancer, and neurodegenerative diseases are all associated with increased FTO expression. Maximization of lactation performance by veterinary medicine with enhanced miRNA-29s and FTO expression associated with increased exosomal miRNA-29 and FTO mRNA transfer to the milk consumer may represent key epigenetic mechanisms promoting FTO/mTORC1-mediated diseases of civilization.

A Mouse Model for the Metabolic Effects of the Human Fat Mass and Obesity Associated FTO Gene

PubMed Central

Church, Chris; Deacon, Robert; Gerken, Thomas; Lee, Angela; Moir, Lee; Mecinović, Jasmin; Quwailid, Mohamed M.; Schofield, Christopher J.; Ashcroft, Frances M.; Cox, Roger D.

2009-01-01

Human FTO gene variants are associated with body mass index and type 2 diabetes. Because the obesity-associated SNPs are intronic, it is unclear whether changes in FTO expression or splicing are the cause of obesity or if regulatory elements within intron 1 influence upstream or downstream genes. We tested the idea that FTO itself is involved in obesity. We show that a dominant point mutation in the mouse Fto gene results in reduced fat mass, increased energy expenditure, and unchanged physical activity. Exposure to a high-fat diet enhances lean mass and lowers fat mass relative to control mice. Biochemical studies suggest the mutation occurs in a structurally novel domain and modifies FTO function, possibly by altering its dimerisation state. Gene expression profiling revealed increased expression of some fat and carbohydrate metabolism genes and an improved inflammatory profile in white adipose tissue of mutant mice. These data provide direct functional evidence that FTO is a causal gene underlying obesity. Compared to the reported mouse FTO knockout, our model more accurately reflects the effect of human FTO variants; we observe a heterozygous as well as homozygous phenotype, a smaller difference in weight and adiposity, and our mice do not show perinatal lethality or an age-related reduction in size and length. Our model suggests that a search for human coding mutations in FTO may be informative and that inhibition of FTO activity is a possible target for the treatment of morbid obesity. PMID:19680540

In situ formation of a ZnO/ZnSe nanonail array as a photoelectrode for enhanced photoelectrochemical water oxidation performance

NASA Astrophysics Data System (ADS)

Wang, Liyang; Tian, Guohui; Chen, Yajie; Xiao, Yuting; Fu, Honggang

2016-04-01

In this study, a ZnO/ZnSe nanonail array was prepared via a two-step sequential hydrothermal synthetic route. In this synthetic process, the ZnO nanorod array was first grown on a fluorine-doped tin oxide (FTO) substrate using a seed-mediated growth approach via the hydrothermal process. Then, the ZnO nanonail array was obtained via in situ growth of ZnSe nano caps onto the ZnO nanorod array via a hydrothermal process in the presence of a Se source. The surface morphology and amount of ZnSe grown on the surface of the ZnO nanorods can be regulated by varying the reaction time and reactant concentration. Compared with pure ZnO nanorods, this unique nanonail array heterostructure exhibits enhanced visible light absorption. The transient photocurrent condition, in combination with steady-state and time-resolved photoluminescence spectroscopy, reveals that the ZnO/ZnSe nanonail array electrode has the highest charge separation rate, highest electron injection efficiency, and highest chemical stability. The photocurrent density of the ZnO/ZnSe nanonail array heterostructure reaches 1.01 mA cm-2 at an applied potential of 0.1 V (vs. Ag/AgCl), which is much higher than that of the ZnO/ZnSe nanorod array (0.71 mA cm-2), the pristine ZnO nanorod array (0.39 mA cm-2), and the ZnSe electrode (0.21 mA cm-2), indicating its significant visible light driven activities for photoelectrochemical water oxidation. This unique morphology of nail-capped nanorods might be important for providing better insight into the correlation between heterostructure and photoelectrochemical activity.In this study, a ZnO/ZnSe nanonail array was prepared via a two-step sequential hydrothermal synthetic route. In this synthetic process, the ZnO nanorod array was first grown on a fluorine-doped tin oxide (FTO) substrate using a seed-mediated growth approach via the hydrothermal process. Then, the ZnO nanonail array was obtained via in situ growth of ZnSe nano caps onto the ZnO nanorod array via a hydrothermal process in the presence of a Se source. The surface morphology and amount of ZnSe grown on the surface of the ZnO nanorods can be regulated by varying the reaction time and reactant concentration. Compared with pure ZnO nanorods, this unique nanonail array heterostructure exhibits enhanced visible light absorption. The transient photocurrent condition, in combination with steady-state and time-resolved photoluminescence spectroscopy, reveals that the ZnO/ZnSe nanonail array electrode has the highest charge separation rate, highest electron injection efficiency, and highest chemical stability. The photocurrent density of the ZnO/ZnSe nanonail array heterostructure reaches 1.01 mA cm-2 at an applied potential of 0.1 V (vs. Ag/AgCl), which is much higher than that of the ZnO/ZnSe nanorod array (0.71 mA cm-2), the pristine ZnO nanorod array (0.39 mA cm-2), and the ZnSe electrode (0.21 mA cm-2), indicating its significant visible light driven activities for photoelectrochemical water oxidation. This unique morphology of nail-capped nanorods might be important for providing better insight into the correlation between heterostructure and photoelectrochemical activity. Electronic supplementary information (ESI) available: SEM, EDS, XPS and photocurrent test. See DOI: 10.1039/c6nr01969b

Interaction between FTO rs9939609 and the Native American-origin ABCA1 rs9282541 affects BMI in the admixed Mexican population.

PubMed

Villalobos-Comparán, Marisela; Antuna-Puente, Bárbara; Villarreal-Molina, María Teresa; Canizales-Quinteros, Samuel; Velázquez-Cruz, Rafael; León-Mimila, Paola; Villamil-Ramírez, Hugo; González-Barrios, Juan Antonio; Merino-García, José Luis; Thompson-Bonilla, María Rocío; Jarquin, Diego; Sánchez-Hernández, Osvaldo Erik; Rodríguez-Arellano, Martha Eunice; Posadas-Romero, Carlos; Vargas-Alarcón, Gilberto; Campos-Pérez, Francisco; Quiterio, Manuel; Salmerón-Castro, Jorge; Carnevale, Alessandra; Romero-Hidalgo, Sandra

2017-05-02

The aim of this study was to explore whether interactions between FTO rs9939609 and ABCA1 rs9282541 affect BMI and waist circumference (WC), and could explain previously reported population differences in FTO-obesity and FTO-BMI associations in the Mexican and European populations. A total of 3938 adults and 636 school-aged children from Central Mexico were genotyped for both polymorphisms. Subcutaneous and visceral adipose tissue biopsies from 22 class III obesity patients were analyzed for FTO and ABCA1 mRNA expression. Generalized linear models were used to test for associations and gene-gene interactions affecting BMI, WC and FTO expression. FTO and ABCA1 risk alleles were not individually associated with higher BMI or WC. However, in the absence of the ABCA1 risk allele, the FTO risk variant was significantly associated with higher BMI (P = 0.043) and marginally associated with higher WC (P = 0.067), as reported in Europeans. The gene-gene interaction affecting BMI and WC was statistically significant only in adults. FTO mRNA expression in subcutaneous abdominal adipose tissue according to ABCA1 genotype was consistent with these findings. This is the first report showing evidence of FTO and ABCA1 gene variant interactions affecting BMI, which may explain previously reported population differences. Further studies are needed to confirm this interaction.

A link between FTO, ghrelin, and impaired brain food-cue responsivity

PubMed Central

Karra, Efthimia; O’Daly, Owen G.; Choudhury, Agharul I.; Yousseif, Ahmed; Millership, Steven; Neary, Marianne T.; Scott, William R.; Chandarana, Keval; Manning, Sean; Hess, Martin E.; Iwakura, Hiroshi; Akamizu, Takashi; Millet, Queensta; Gelegen, Cigdem; Drew, Megan E.; Rahman, Sofia; Emmanuel, Julian J.; Williams, Steven C.R.; Rüther, Ulrich U.; Brüning, Jens C.; Withers, Dominic J.; Zelaya, Fernando O.; Batterham, Rachel L.

2013-01-01

Polymorphisms in the fat mass and obesity-associated gene (FTO) are associated with human obesity and obesity-prone behaviors, including increased food intake and a preference for energy-dense foods. FTO demethylates N6-methyladenosine, a potential regulatory RNA modification, but the mechanisms by which FTO predisposes humans to obesity remain unclear. In adiposity-matched, normal-weight humans, we showed that subjects homozygous for the FTO “obesity-risk” rs9939609 A allele have dysregulated circulating levels of the orexigenic hormone acyl-ghrelin and attenuated postprandial appetite reduction. Using functional MRI (fMRI) in normal-weight AA and TT humans, we found that the FTO genotype modulates the neural responses to food images in homeostatic and brain reward regions. Furthermore, AA and TT subjects exhibited divergent neural responsiveness to circulating acyl-ghrelin within brain regions that regulate appetite, reward processing, and incentive motivation. In cell models, FTO overexpression reduced ghrelin mRNA N6-methyladenosine methylation, concomitantly increasing ghrelin mRNA and peptide levels. Furthermore, peripheral blood cells from AA human subjects exhibited increased FTO mRNA, reduced ghrelin mRNA N6-methyladenosine methylation, and increased ghrelin mRNA abundance compared with TT subjects. Our findings show that FTO regulates ghrelin, a key mediator of ingestive behavior, and offer insight into how FTO obesity-risk alleles predispose to increased energy intake and obesity in humans. PMID:23867619

A link between FTO, ghrelin, and impaired brain food-cue responsivity.

PubMed

Karra, Efthimia; O'Daly, Owen G; Choudhury, Agharul I; Yousseif, Ahmed; Millership, Steven; Neary, Marianne T; Scott, William R; Chandarana, Keval; Manning, Sean; Hess, Martin E; Iwakura, Hiroshi; Akamizu, Takashi; Millet, Queensta; Gelegen, Cigdem; Drew, Megan E; Rahman, Sofia; Emmanuel, Julian J; Williams, Steven C R; Rüther, Ulrich U; Brüning, Jens C; Withers, Dominic J; Zelaya, Fernando O; Batterham, Rachel L

2013-08-01

Polymorphisms in the fat mass and obesity-associated gene (FTO) are associated with human obesity and obesity-prone behaviors, including increased food intake and a preference for energy-dense foods. FTO demethylates N6-methyladenosine, a potential regulatory RNA modification, but the mechanisms by which FTO predisposes humans to obesity remain unclear. In adiposity-matched, normal-weight humans, we showed that subjects homozygous for the FTO "obesity-risk" rs9939609 A allele have dysregulated circulating levels of the orexigenic hormone acyl-ghrelin and attenuated postprandial appetite reduction. Using functional MRI (fMRI) in normal-weight AA and TT humans, we found that the FTO genotype modulates the neural responses to food images in homeostatic and brain reward regions. Furthermore, AA and TT subjects exhibited divergent neural responsiveness to circulating acyl-ghrelin within brain regions that regulate appetite, reward processing, and incentive motivation. In cell models, FTO overexpression reduced ghrelin mRNA N6-methyladenosine methylation, concomitantly increasing ghrelin mRNA and peptide levels. Furthermore, peripheral blood cells from AA human subjects exhibited increased FTO mRNA, reduced ghrelin mRNA N6-methyladenosine methylation, and increased ghrelin mRNA abundance compared with TT subjects. Our findings show that FTO regulates ghrelin, a key mediator of ingestive behavior, and offer insight into how FTO obesity-risk alleles predispose to increased energy intake and obesity in humans.

Fast Fabrication of a Stable Perovskite Solar Cell with an Ultrathin Effective Novel Inorganic Hole Transport Layer.

PubMed

Huang, Aibin; Lei, Lei; Zhu, Jingting; Yu, Yu; Liu, Yan; Yang, Songwang; Bao, Shanhu; Cao, Xun; Jin, Ping

2017-04-18

With the aim of fabricating simple, reproducible, and scalable perovskite solar cells (PSCs) with least time consumption, a novel CoO x hole transport layer (HTL) was first proposed and introduced in this work. The CoO x HTL thickness was minimized to about 10 nm with complete coverage on the FTO substrate (F-doped SnO 2 ) by direct current magnetron sputtering. The ultrathin HTL could minimize the incident light loss caused by cobalt ion absorption and reduce the carrier transport loss by shortening the transport path. Copper was incorporated into the CoO x lattice to address the low conductivity of the CoO x film and the energy-level mismatch between CoO x and the perovskite material. On the basis of cobalt-copper binary oxide (Co 1-y Cu y O x ), the highest power conversion efficiency (PCE) of about 10% was achieved, which was acceptable for mass production. Moreover, the deposition of such Co 1-y Cu y O x films takes only 2 min without size limitation of substrates. A well-functioned device based on the Co 1-y Cu y O x HTL could hence be fabricated within 100 min. Excellent stability was demonstrated as well, with over 90% of the initial PCE remaining after being stored in a dark and humid environment (relative humidity 60%) for 12 days.

Tunable TiO2 Nanotube Arrays for Flexible Bio-Sensitized Solar Cells

DTIC Science & Technology

2012-08-01

microid extender followed by a colloidal silica /wetted imperial cloth. The foil was then cut into 1- × 2-cm samples. Then, the substrates were...17. Lei, B.; Liao, J.; Wang, R. J.; Su, C.; Kuang, D. Ordered Crystalline Ti02 Nanotube Arrays on Transparent FTO Glass for Efficient Dye...combined with a transparent , Indium Tin Dioxide coated PET film are attractive candidates for efficient, flexible DSSC’s. Flexible solar cells offer

Improved performance of CdSe/CdS co-sensitized solar cells adopting efficient CuS counter electrode modified by PbS film using SILAR method

NASA Astrophysics Data System (ADS)

Zhang, Xiaolong; Lin, Yu; Wu, Jihuai; Fang, Biaopeng; Zeng, Jiali

2018-04-01

In this paper, CuS film was deposited onto fluorine-doped tin oxide (FTO) substrate using a facile chemical bath deposition method, and then modified by PbS using simple successive ionic layer absorption and reaction (SILAR) method with different cycles. These CuS/PbS films were utilized as counter electrodes (CEs) for CdSe/CdS co-sensitized solar cells. Field-emission scanning electron microscopy equipped with an energy-dispersive X-ray spectrometer was used to characterize the CuS/PbS films. The results show that CuS/PbS (10 cycles) CE exhibits an improved power conversion efficiency of 5.54% under the illumination of one sun (100 mW cm-2), which is higher than the CuS/PbS (0 cycles), CuS/PbS (5 cycles), and CuS/PbS (15 cycles) CEs. This enhancement is mainly attributed to good catalytic activity and lower charge-transfer and series resistances, which have been proved by electrochemical impedance spectroscopy, and Tafel polarization measurements.

Preparation of electrochromic thin films by transformation of manganese(II) carbonate

NASA Astrophysics Data System (ADS)

Stojkovikj, Sasho; Najdoski, Metodija; Koleva, Violeta; Demiri, Sani

2013-10-01

A new chemical bath method for deposition of manganese(II) carbonate thin film on electroconductive FTO glass substrates is designed. The homogeneous thin films with thickness in the range of 70 to 500 nm are deposited at about 98 °C from aqueous solution containing urea and MnCl2. The chemical process is based on a low temperature hydrolysis of the manganese complexes with urea. Three types of films are under consideration: as-deposited, annealed and electrochemically transformed thin films. The structure of the films is studied by XRD, IR and Raman spectroscopy. Electrochemical and optical properties are examined in eight different electrolytes (neutral and alkaline) and the best results are achieved in two component aqueous solution of 0.1 M KNO3 and 0.01 M KOH. It is established that the as-deposited MnCO3 film undergoes electrochemically transformation into birnessite-type manganese(IV) oxide films, which exhibit electrochromic color changes (from bright brown to pale yellow and vice versa) with 30% difference in the transmittance of the colored and bleached state at 400 nm.

Atmospheric-pressure plasma jet processed Pt/ZnO composites and its application as counter-electrodes for dye-sensitized solar cells

NASA Astrophysics Data System (ADS)

Lee, Chia-Chun; Wan, Ting-Hao; Hsu, Cheng-Che; Cheng, I.-Chun; Chen, Jian-Zhang

2018-04-01

Nitrogen dc-pulse atmospheric pressure plasma jet (APPJ) is used to fabricate Pt/ZnO composites as the counter electrodes (CEs) of dye-sensitized solar cells (DSSCs). Due to the synergetic effect of the reactive plasma species and heat in nitrogen APPJ, the spin-coated precursors including chloroplatinic acid and zinc acetate can be reduced on fluorine-doped tin oxide (FTO) glass substrates in a few seconds. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) analyses indicate that the precursors are reduced to Pt/ZnO under APPJ calcination. Electrochemical impedance spectroscopy (EIS) and Tafel measurement show the promising catalytic activities of Pt/ZnO CEs with low charge transfer resistance and high exchange current density. The efficiency of a DSSC with a 30-s APPJ-calcined Pt/ZnO CE is similar to that with a conventional furnace-annealed Pt CE for 15 min. The results indicate that nitrogen dc-pulse APPJ treatment is an efficient tool for rapidly fabricating Pt/ZnO composite CEs of DSSCs.

Hybrid structure of polyaniline/ZnO nanograss and its application in dye-sensitized solar cell with performance improvement

NASA Astrophysics Data System (ADS)

Zhu, Shibu; Wei, Wei; Chen, Xiangnan; Jiang, Man; Zhou, Zuowan

2012-06-01

Polyaniline (PANI) hybridized ZnO photoanode for dye-sensitized solar cell (DSSC) was primarily prepared via a two-step process which involved hydrothermal growth of ZnO nanograss on the fluorine-doped tin oxide (FTO) substrate and subsequently chemisorption of PANI on the surfaces of the ZnO nanorods. The PANI hybridized ZnO nanograss films were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectra (FT-IR), and the results indicated that there were chemical interactions between PANI and ZnO. Both pure ZnO nanograss and PANI hybridized ZnO nanograss were applied to DSSC. The results of photoelectrochemical measurement showed that the photocurrent density of PANI (100 mg/L) hybridized ZnO nanograss photoanode was significantly enhanced, and the overall light-conversion efficiency increased by 60%. The electrochemical impedance spectra (EIS) displayed that the electron densities in photoanodes of PANI hybridized ZnO nanograss were larger than that in pure ZnO nanograss. This is ascribed to more effective charge separation and faster interfacial charge transferring occurred in the hybrid photoanode.

Impedimetric genosensor for detection of hepatitis C virus (HCV1) DNA using viral probe on methylene blue doped silica nanoparticles.

PubMed

Singhal, Chaitali; Ingle, Aviraj; Chakraborty, Dhritiman; Pn, Anoop Krishna; Pundir, C S; Narang, Jagriti

2017-05-01

An impedimetric genosensor was fabricated for detection of hepatitis C virus (HCV) genotype 1 in serum, based on hybridization of the probe with complementary target cDNA from sample. To achieve it, probe DNA complementary to HCVgene was immobilized on the surface of methylene blue (MB) doped silica nanoparticles MB@SiNPs) modified fluorine doped tin oxide (FTO) electrode. The synthesized MB@SiNPs was characterized using scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and X-ray diffraction (XRD) pattern. This modified electrode (ssDNA/MB@SiNPs/FTO) served both as a signal amplification platform (due to silica nanoparticles (SiNPs) as well as an electrochemical indicator (due to methylene blue (MB)) for the detection of the HCV DNA in patient serum sample. The genosensor was optimized and evaluated. The sensor showed a dynamic linear range 100-10 6 copies/mL, with a detection limit of 90 copies/mL. The sensor was applied for detection of HCV in sera of hepatitis patient and could be renewed. The half life of the sensor was 4 weeks. The MB@SiNPs/FTO electrode could be used for preparation of other gensensors also. Copyright © 2017 Elsevier B.V. All rights reserved.

Properties of Semiconductors: Synthesis of Oriented ZnO for Photoelectrochemistry and Photoremediation

ERIC Educational Resources Information Center

Koenig, Emma; Jacobs, Ari; Lisensky, George

2017-01-01

Semiconductors are an important class of materials; preparing ZnO nanorods allows semiconducting properties to be easily observed. The week before lab, groups of four students take 15 min to setup two fluorine-doped tin oxide glass (FTO) slides in a zinc nitrate and hexamethylenetetramine solution stored at 90°C until the next lab. Hexagonal ZnO…

A Synergistic Effect of Surfactant and ZrO2 Underlayer on Photocurrent Enhancement and Cathodic Shift of Nanoporous Fe2O3 Photoanode.

PubMed

Shinde, Pravin S; Lee, Su Yong; Choi, Sun Hee; Lee, Hyun Hwi; Ryu, Jungho; Jang, Jum Suk

2016-08-31

Augmenting the donor density and nanostructure engineering are the crucial points to improve solar water oxidation performance of hematite (α-Fe2O3). This work addresses the sluggish water oxidation reaction associated with hematite photoanode by tweaking its internal porosity. The porous hematite photoanodes are fabricated by a novel synthetic strategy via pulse reverse electrodeposition (PRED) method that involves incorporation of a cationic CTAB surfactant in a sulfate electrolyte and spin-coated ZrO2 underlayer (UL) on FTO. CTAB is found to be beneficial in promoting the film growth rate during PRED. Incorporation of Zr(4+) ions from ZrO2 UL and Sn(4+) ions from FTO into the Fe2O3 lattice via solid-state diffusion reaction during pertinent annihilation of surfactant molecules at 800 °C produced internally porous hematite films with improved carrier concentration. The porous hematite demonstrated a sustained photocurrent enhancement and a significant cathodic shift of 130 mV relative to the planar hematite under standard illumination conditions (AM 1.5G) in 1 M NaOH electrolyte. The absorption, electrochemical impedance spectroscopy and Mott-Schottky analyses revealed that the ZrO2 UL and CTAB not only increased the carrier density and light harvesting but also accelerated the surface oxidation reaction kinetics, synergistically boosting the performance of internally porous hematite photoanodes.

A Synergistic Effect of Surfactant and ZrO2 Underlayer on Photocurrent Enhancement and Cathodic Shift of Nanoporous Fe2O3 Photoanode

NASA Astrophysics Data System (ADS)

Shinde, Pravin S.; Lee, Su Yong; Choi, Sun Hee; Lee, Hyun Hwi; Ryu, Jungho; Jang, Jum Suk

2016-08-01

Augmenting the donor density and nanostructure engineering are the crucial points to improve solar water oxidation performance of hematite (α-Fe2O3). This work addresses the sluggish water oxidation reaction associated with hematite photoanode by tweaking its internal porosity. The porous hematite photoanodes are fabricated by a novel synthetic strategy via pulse reverse electrodeposition (PRED) method that involves incorporation of a cationic CTAB surfactant in a sulfate electrolyte and spin-coated ZrO2 underlayer (UL) on FTO. CTAB is found to be beneficial in promoting the film growth rate during PRED. Incorporation of Zr4+ ions from ZrO2 UL and Sn4+ ions from FTO into the Fe2O3 lattice via solid-state diffusion reaction during pertinent annihilation of surfactant molecules at 800 °C produced internally porous hematite films with improved carrier concentration. The porous hematite demonstrated a sustained photocurrent enhancement and a significant cathodic shift of 130 mV relative to the planar hematite under standard illumination conditions (AM 1.5G) in 1 M NaOH electrolyte. The absorption, electrochemical impedance spectroscopy and Mott-Schottky analyses revealed that the ZrO2 UL and CTAB not only increased the carrier density and light harvesting but also accelerated the surface oxidation reaction kinetics, synergistically boosting the performance of internally porous hematite photoanodes.

Fabrication of large-scale ripples on fluorine-doped tin oxide films by femtosecond laser irradiation

NASA Astrophysics Data System (ADS)

Han, Yan-Hua; Li, Yan; Zhao, Xiu-Li; Qu, Shi-Liang

2014-09-01

The large-scale uniform self-organized ripples are fabricated on fluorine-doped tin oxide (FTO) coated glass by femtosecond laser. They can be smoothly linked in a horizontal line with the moving of XYZ stage by setting its velocity and the repetition rate of the laser. The ripple-to-ripple linking can also be realized through line-by-line scanning on a vertical level. The mechanism analysis shows that the seeding effect plays a key role in the linking of ripples.

Protein kinase Cβ activates fat mass and obesity-associated protein by influencing its ubiquitin/proteasome degradation.

PubMed

Tai, Haoran; Wang, Xiaobo; Zhou, Jiao; Han, Xiaojuan; Fang, Tingting; Gong, Hui; Huang, Ning; Chen, Honghan; Qin, Jianqiong; Yang, Ming; Wei, Xiawei; Yang, Li; Xiao, Hengyi

2017-10-01

Protein kinase Cβ (PKCβ) is a serine-threonine kinase associated with obesity and diabetic complications; its activation contributes to weight gain, and deletion of its gene results in resistance to genetic- and diet-induced obesity. Fat mass and obesity-associated (FTO) protein is a recently identified RNA demethylase, and its overexpression in mice leads to increased body weight as well as fat mass. Although sharing some features in anabolism regulation, PKCβ and FTO have not been investigated together; therefore, their relationship has not been established. We report that PKCβ positively regulates FTO on the posttranslation level, evidenced by the facts that PKCβ activation contributes to high-glucose-induced FTO up-regulation, and overexpression of PKCβ suppresses ubiquitin-proteasome degradation of FTO, whereas PKCβ inactivation acts in the opposite manner. It was also found that PKCβ can phosphorylate FTO on threonine, and this phosphorylation requires both catalytic and regulatory domains of PKCβ. Moreover, PKCβ inhibition can suppress 3T3-L1 cell differentiation in normal and FTO-overexpressing cells but not in FTO-silenced or -inhibited cells. We propose that PKCβ acts to suppress the degradation of FTO protein and reveals the associated role of PKCβ and FTO in adipogenesis, suggesting a new pathway that affects the development of obesity and metabolic diseases.-Tai, H., Wang, X., Zhou, J., Han, X., Fang, T., Gong, H., Huang, N., Chen, H., Qin, J., Yang, M., Wei, X., Yang, L., Xiao, H. Protein kinase Cβ activates fat mass and obesity-associated protein by influencing its ubiquitin/proteasome degradation. © FASEB.

Influence of silver doping on surface defect characteristics of TiO{sub 2}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tripathi, S. K., E-mail: surya@pu.ac.in; Rani, Mamta; Department of Physics, DAV University Jalandhar, - 144 001, Punjab

2015-08-28

In the present work, we proposed a novel silver doped TiO{sub 2} polyethylene conjugated films to improve the performance of DSSCs. Oxides nanoparticles dispersed in a semiconducting polymer form the active layer of a solar cell. Localized surface plasmon resonance effects associated with spatially dispersed silver (Ag) nanoparticles can be exploited to enhance the light-harvesting efficiency, the photocurrent density and the overall light-to electrical-energy-conversion efficiency of high-area DSSCs based TiO{sub 2} photoanodes. Silver doped titanium dioxide (TiO{sub 2}:Ag) is prepared by sol-gel technique and deposited on fluorine doped indium oxide (FTO) coated glass substrates by using doctor blade technique atmore » 550°C from aqueous solutions of titanium butoxide and silver nitrate precursors. The effect of Ag doping on electrical properties of films is studied. The Ag-TiO{sub 2} films are about 548 times more photosensitive as compare to the pure TiO{sub 2} sample. The presence of metallic Ag nanoparticles and oxygen vacancy on the surface of TiO{sub 2} nanoparticles promotes the separation of photogenerated electron-hole pairs and thus enhances the photosensitivity. Photoconduction mechanism of all prepared samples is investigated by performing transient photoconductivity measurements on TiO{sub 2} and Ag-TiO{sub 2} films keeping intensity of light constant.« less

Adult Onset Global Loss of the Fto Gene Alters Body Composition and Metabolism in the Mouse

PubMed Central

Wells, Sara; Teboul, Lydia; Tung, Y. C. Loraine; Rimmington, Debra; Bosch, Fatima; Jimenez, Veronica; Yeo, Giles S. H.; O'Rahilly, Stephen; Ashcroft, Frances M.; Coll, Anthony P.; Cox, Roger D.

2013-01-01

The strongest BMI–associated GWAS locus in humans is the FTO gene. Rodent studies demonstrate a role for FTO in energy homeostasis and body composition. The phenotypes observed in loss of expression studies are complex with perinatal lethality, stunted growth from weaning, and significant alterations in body composition. Thus understanding how and where Fto regulates food intake, energy expenditure, and body composition is a challenge. To address this we generated a series of mice with distinct temporal and spatial loss of Fto expression. Global germline loss of Fto resulted in high perinatal lethality and a reduction in body length, fat mass, and lean mass. When ratio corrected for lean mass, mice had a significant increase in energy expenditure, but more appropriate multiple linear regression normalisation showed no difference in energy expenditure. Global deletion of Fto after the in utero and perinatal period, at 6 weeks of age, removed the high lethality of germline loss. However, there was a reduction in weight by 9 weeks, primarily as loss of lean mass. Over the subsequent 10 weeks, weight converged, driven by an increase in fat mass. There was a switch to a lower RER with no overall change in food intake or energy expenditure. To test if the phenotype can be explained by loss of Fto in the mediobasal hypothalamus, we sterotactically injected adeno-associated viral vectors encoding Cre recombinase to cause regional deletion. We observed a small reduction in food intake and weight gain with no effect on energy expenditure or body composition. Thus, although hypothalamic Fto can impact feeding, the effect of loss of Fto on body composition is brought about by its actions at sites elsewhere. Our data suggest that Fto may have a critical role in the control of lean mass, independent of its effect on food intake. PMID:23300482

FTO Polymorphisms Moderate the Association of Food Reinforcement with Energy Intake

PubMed Central

Scheid, Jennifer L.; Carr, Katelyn A.; Lin, Henry; Fletcher, Kelly D.; Sucheston, Lara; Singh, Prashant K.; Salis, Robbert; Erbe, Richard; Faith, Myles S.; Allison, David B.; Epstein, Leonard H.

2015-01-01

Food reinforcement (RRVfood) is related to increased energy intake, cross-sectionally related to obesity, and prospectively related to weight gain. The fat mass and obesity-associated (FTO) gene is related to elevated body mass index and increased energy intake. The primary purpose of the current study was to determine whether any of 68 FTO single nucleotide polymorphisms (SNPs) or a FTO risk score moderate the association between food reinforcement and energy or macronutrient intake. Energy and macronutrient intake was measured using a laboratory ad libitum snack food consumption task in 237 adults of varying BMI. Controlling for BMI, the relative reinforcing value of reading (RRVreading) and proportion of African ancestry, RRVfood predicted 14.2% of the variance in energy intake, as well as predicted carbohydrate, fat, protein and sugar intake. In individual analyses, six FTO SNPs (rs12921970, rs9936768, rs12446047, rs7199716, rs8049933 and rs11076022, spanning approximately 251K bp) moderated the relationship between RRVfood and energy intake to predict an additional 4.9 - 7.4% of variance in energy intake. We created an FTO risk score based on 5 FTO SNPs (rs9939609, rs8050136, rs3751812, rs1421085, and rs1121980) that are related to BMI in multiple studies. The FTO risk score did not increase variance accounted for beyond individual FTO SNPs. Rs12921970 and rs12446047 served as moderators of the relationship between RRVfood and carbohydrate, fat, protein, and sugar intake. This study shows for the first time that the relationship between RRVfood and energy intake is moderated by FTO SNPs. Research is needed to understand how these processes interact to predict energy and macronutrient intake. PMID:24768648

Aerobic fitness does not modify the effect of FTO variation on body composition traits.

PubMed

Huuskonen, Antti; Lappalainen, Jani; Oksala, Niku; Santtila, Matti; Häkkinen, Keijo; Kyröläinen, Heikki; Atalay, Mustafa

2012-01-01

Poor physical fitness and obesity are risk factors for all cause morbidity and mortality. We aimed to clarify whether common genetic variants of key energy intake determinants in leptin (LEP), leptin receptor (LEPR), and fat mass and obesity-associated (FTO) are associated with aerobic and neuromuscular performance, and whether aerobic fitness can alter the effect of these genotypes on body composition. 846 healthy Finnish males of Caucasian origin were genotyped for FTO (rs8050136), LEP (rs7799039) and LEPR (rs8179183 and rs1137101) single nucleotide polymorphisms (SNPs), and studied for associations with maximal oxygen consumption, body fat percent, serum leptin levels, waist circumference and maximal force of leg extensor muscles. Genotype AA of the FTO SNP rs8050136 associated with higher BMI and greater waist circumference compared to the genotype CC. In general linear model, no significant interaction for FTO genotype-relative VO(2)max (mL·kg(-1)·min(-1)) or FTO genotype-absolute VO(2)max (L·min(-1)) on BMI or waist circumference was found. Main effects of aerobic performance on body composition traits were significant (p<0.001). Logistic regression modelling found no significant interaction between aerobic fitness and FTO genotype. LEP SNP rs7799039, LEPR SNPs rs8179183 and rs1137101 did not associate with any of the measured variables, and no significant interactions of LEP or LEPR genotype with aerobic fitness were observed. In addition, none of the studied SNPs associated with aerobic or neuromuscular performance. Aerobic fitness may not modify the effect of FTO variation on body composition traits. However, relative aerobic capacity associates with lower BMI and waist circumference regardless of the FTO genotype. FTO, LEP and LEPR genotypes unlikely associate with physical performance.

FTO polymorphisms moderate the association of food reinforcement with energy intake.

PubMed

Scheid, Jennifer L; Carr, Katelyn A; Lin, Henry; Fletcher, Kelly D; Sucheston, Lara; Singh, Prashant K; Salis, Robbert; Erbe, Richard W; Faith, Myles S; Allison, David B; Epstein, Leonard H

2014-06-10

Food reinforcement (RRVfood) is related to increased energy intake, cross-sectionally related to obesity, and prospectively related to weight gain. The fat mass and obesity-associated (FTO) gene is related to elevated body mass index and increased energy intake. The primary purpose of the current study was to determine whether any of 68 FTO single nucleotide polymorphisms (SNPs) or a FTO risk score moderate the association between food reinforcement and energy or macronutrient intake. Energy and macronutrient intake was measured using a laboratory ad libitum snack food consumption task in 237 adults of varying BMI. Controlling for BMI, the relative reinforcing value of reading (RRVreading) and proportion of African ancestry, RRVfood predicted 14.2% of the variance in energy intake, as well as predicted carbohydrate, fat, protein and sugar intake. In individual analyses, six FTO SNPs (rs12921970, rs9936768, rs12446047, rs7199716, rs8049933 and rs11076022, spanning approximately 251kbp) moderated the relationship between RRVfood and energy intake to predict an additional 4.9-7.4% of variance in energy intake. We created an FTO risk score based on 5 FTO SNPs (rs9939609, rs8050136, rs3751812, rs1421085, and rs1121980) that are related to BMI in multiple studies. The FTO risk score did not increase variance accounted for beyond individual FTO SNPs. rs12921970 and rs12446047 served as moderators of the relationship between RRVfood and carbohydrate, fat, protein, and sugar intake. This study shows for the first time that the relationship between RRVfood and energy intake is moderated by FTO SNPs. Research is needed to understand how these processes interact to predict energy and macronutrient intake. Copyright © 2014 Elsevier Inc. All rights reserved.

Electrochemical Synthesis of Bismuth Particles: Tuning Particle Shape through Substrate Type within a Narrow Potential Window

PubMed Central

Bilican, Doga; Fornell, Jordina; Sort, Jordi; Pellicer, Eva

2017-01-01

Bismuth (Bi) electrodeposition was studied on Si/Ti/Au, FTO-, and ITO-coated glasses from acidic nitrate solutions with and without gluconate within a narrow potential window (ΔE = 80 mV). This potential range was sufficient to observe a change in particle shape, from polyhedrons (including hexagons) to dendrites, the trend being slightly different depending on substrate activity. In all cases, though, the formation of dendrites was favoured as the applied potential was made more negative. Bi particles were more uniformly distributed over the substrate when sodium gluconate was added to the electrolyte. X-ray diffraction analyses of dendrites grown at −0.28 V indicated that they exhibit the rhombohedral phase of Bi and are predominantly oriented along the (003) plane. This orientation is exacerbated at the lowest applied potential (−0.20 V vs. Ag|AgCl) on glass/ITO substrate, for which completed and truncated hexagons are observed from the top view scanning electron microscopy images. PMID:28772402

Seebeck coefficient of synthesized Titanium Dioxide thin film on FTO glass substrate

NASA Astrophysics Data System (ADS)

Usop, R.; Hamed, N. K. A.; Megat Hasnan, M. M. I.; Ikeda, H.; Sabri, M. F. M.; Ahmad, M. K.; Said, S. M.; Salleh, F.

2018-04-01

In order to fabricate a thermoelectric device on glass substrate for harvesting waste heat energy through house appliances, the Seebeck coefficient of translucent TiO2 thin film was investigated. The TiO2 thin film was synthesized by using hydrothermal method with F-SnO2 coated glass as substrate. From scanning electron microscopy analysis, the synthesized TiO2 thin film was found to be in nanometer-scale rod structure with a thickness of 4 µm. The Seebeck coefficient was measured in the temperature range of 300 – 400 K. The Seebeck coefficient is found to be in negative value which shows that synthesized film is an n-type semiconductor material, and is lower than the value of bulk-size material. This reduction in Seebeck coefficient of TiO2 thin film is likely due to the low dimensional effect and the difference of carrier concentration.

Facile fabrication of an efficient BiVO4 thin film electrode for water splitting under visible light irradiation.

PubMed

Jia, Qingxin; Iwashina, Katsuya; Kudo, Akihiko

2012-07-17

An efficient BiVO(4) thin film electrode for overall water splitting was prepared by dipping an F-doped SnO(2) (FTO) substrate electrode in an aqueous nitric acid solution of Bi(NO(3))(3) and NH(4)VO(3), and subsequently calcining it. X-ray diffraction of the BiVO(4) thin film revealed that a photocatalytically active phase of scheelite-monoclinic BiVO(4) was obtained. Scanning electron microscopy images showed that the surface of an FTO substrate was uniformly coated with the BiVO(4) film with 300-400 nm of the thickness. The BiVO(4) thin film electrode gave an excellent anodic photocurrent with 73% of an IPCE at 420 nm at 1.0 V vs. Ag/AgCl. Modification with CoO on the BiVO(4) electrode improved the photoelectrochemical property. A photoelectrochemical cell consisting of the BiVO(4) thin film electrode with and without CoO, and a Pt counter electrode was constructed for water splitting under visible light irradiation and simulated sunlight irradiation. Photocurrent due to water splitting to form H(2) and O(2) was confirmed with applying an external bias smaller than 1.23 V that is a theoretical voltage for electrolysis of water. Water splitting without applying external bias under visible light irradiation was demonstrated using a SrTiO(3)Rh photocathode and the BiVO(4) photoanode.

Genetic association of SNPs in the FTO gene and predisposition to obesity in Malaysian Malays.

PubMed

Apalasamy, Y D; Ming, M F; Rampal, S; Bulgiba, A; Mohamed, Z

2012-12-01

The common variants in the fat mass- and obesity-associated (FTO) gene have been previously found to be associated with obesity in various adult populations. The objective of the present study was to investigate whether the single nucleotide polymorphisms (SNPs) and linkage disequilibrium (LD) blocks in various regions of the FTO gene are associated with predisposition to obesity in Malaysian Malays. Thirty-one FTO SNPs were genotyped in 587 (158 obese and 429 non-obese) Malaysian Malay subjects. Obesity traits and lipid profiles were measured and single-marker association testing, LD testing, and haplotype association analysis were performed. LD analysis of the FTO SNPs revealed the presence of 57 regions with complete LD (D' = 1.0). In addition, we detected the association of rs17817288 with low-density lipoprotein cholesterol. The FTO gene may therefore be involved in lipid metabolism in Malaysian Malays. Two haplotype blocks were present in this region of the FTO gene, but no particular haplotype was found to be significantly associated with an increased risk of obesity in Malaysian Malays.

Genetic association of SNPs in the FTO gene and predisposition to obesity in Malaysian Malays

PubMed Central

Apalasamy, Y.D.; Ming, M.F.; Rampal, S.; Bulgiba, A.; Mohamed, Z.

2012-01-01

The common variants in the fat mass- and obesity-associated (FTO) gene have been previously found to be associated with obesity in various adult populations. The objective of the present study was to investigate whether the single nucleotide polymorphisms (SNPs) and linkage disequilibrium (LD) blocks in various regions of the FTO gene are associated with predisposition to obesity in Malaysian Malays. Thirty-one FTO SNPs were genotyped in 587 (158 obese and 429 non-obese) Malaysian Malay subjects. Obesity traits and lipid profiles were measured and single-marker association testing, LD testing, and haplotype association analysis were performed. LD analysis of the FTO SNPs revealed the presence of 57 regions with complete LD (D' = 1.0). In addition, we detected the association of rs17817288 with low-density lipoprotein cholesterol. The FTO gene may therefore be involved in lipid metabolism in Malaysian Malays. Two haplotype blocks were present in this region of the FTO gene, but no particular haplotype was found to be significantly associated with an increased risk of obesity in Malaysian Malays. PMID:22911346

Efficient interfacial charge transfer through plasmon sensitized Ag@Bi2O3 hierarchical photoanodes for photoelectrocatalytic degradation of chlorinated phenols.

PubMed

Eswar, Neerugatti KrishnaRao; Adhikari, Sangeeta; Ramamurthy, Praveen C; Madras, Giridhar

2018-01-31

The present work demonstrates an extremely proficient and robust study of efficient interfacial charge transfer through plasmonic Ag decorated Bi 2 O 3 hierarchical photoanodes for the photoelectrochemical treatment of chlorinated phenols. Unique 2D flake-like Bi 2 O 3 hierarchical nanostructures were grown onto a fluorine-doped tin oxide (FTO) substrate by a simple chemical bath deposition method using triethanolamine as complexing agent. The formation of Bi 2 O 3 on FTO was governed by the decomposition of a nucleated bismuth-hydroxyl complex (Bi 2 O 1-x (OH) x ) and modification to the electrode was carried out by the deposition of Ag via a chemical reduction method using hydrazine hydrate. Both the fabricated electrodes were well characterized for their photo- and electro-optical properties. Efficient charge separation was observed due to the surface plasmon resonance phenomenon of silver nanoparticles with the favorable intrinsic properties of Bi 2 O 3 under application of a small electric bias of 1 V preventing the recombination of charge carriers and thereby increasing the rate of photoelectrocatalytic degradation of the chlorinated phenols. PEC degradation using the Ag@Bi 2 O 3 photoelectrode followed the trend 4-CP < 2,4-DCP < 2,4,6-TCP < P-CP due to efficient attack at the chlorinated positions by reactive oxygen species with increasing chlorine substitution and also due to the absence of an expected chain reaction of the generated chlorine radicals (Cl˙) during the PEC reaction. The PEC activity of Ag@Bi 2 O 3 was 1.5 times higher than a Bi 2 O 3 nanoflake electrode for 4-CP over 2 h. The fabricated Ag@Bi 2 O 3 proved to be an efficient photoelectrode with synergistic solar-induced photoactivity. A detailed mechanistic study in the presence of scavengers suggests degradation by produced hydroxyl radical species. Thus, physical insights into the degradation of chlorinated phenols were obtained.

Enhanced photovoltaic performance of CdS-sensitized inverted organic solar cells prepared via a successive ionic layer adsorption and reaction method

NASA Astrophysics Data System (ADS)

Oleiwi, Hind Fadhil; Zakaria, Azmi; Yap, Chi Chin; Abbas, Haidr Abdulzahra; Tan, Sin Tee; Lee, Hock Beng; Tan, Chun Hui; Ginting, Riski Titian; Alshanableh, Abdelelah; Talib, Zainal Abidin

2017-05-01

One-dimensional ZnO nanorods (ZNRs) synthesized on fluorine-doped tin oxide (FTO) glass by hydrothermal method were modified with cadmium sulfide quantum dots (CdS QDs) as an electron transport layer (ETL) in order to enhance the photovoltaic performance of inverted organic solar cell (IOSC). In present study, CdS QDs were deposited on ZNRs using a Successive Ionic Layer Adsorption and Reaction method (SILAR) method. In typical procedures, IOSCs were fabricated by spin-coating the P3HT:PC61BM photoactive layer onto the as-prepared ZNRs/CdS QDs. The results of current-voltage (I-V) measurement under illumination shows that the FTO/ZNRs/CdS QDs/ P3HT:PC61BM/ PEDOT: PSS/Ag IOSC achieved a higher power conversion efficiency (4.06 %) in comparison to FTO/ZNRs/P3HT:PC61BM/PEDOT: PSS/Ag (3.6 %). Our findings suggest that the improved open circuit voltage (Voc) and short circuit current density (Jsc) of ZNRs/CdS QDs devices could be attributed to enhanced electron selectivity and reduced interfacial charge carrier recombination between ZNRs and P3HT:PC61BM after the deposition of CdS QDs. The CdS QDs sensitized ZNRs reported herein exhibit great potential for advanced optoelectronic application.

Improvement of antimony sulfide photo absorber performance by interface modification in Sb2S3-ZnO hybrid nanostructures

NASA Astrophysics Data System (ADS)

Ali, Asad; Hasanain, Syed Khurshid; Ali, Tahir; Sultan, Muhammad

2017-03-01

Metal-oxide chalcogenide nanostructures as part of hybrid systems are very important for photovoltaic and optoelectronic applications. It is however known that the various interfaces within the hybrid structures play a crucial role in limiting the efficiency of these devices. Here we report on the improvement of Sb2S3 structure through modification of interface between Zn-oxide nanostructures and chalcogenides. ZnO nanorods were grown on fluorine doped tin oxide (FTO) substrate by chemical bath deposition (CBD) method. X-ray diffraction (XRD) and SEM analysis confirmed the single phase wurtzite structure and c-axis orientation of the ZnO nanorod arrays. Antimony tri-sulfide (Sb2S3) was deposited on ZnO nanords by CBD and subsequently annealed at 300 °C in argon environment for 30 min. XRD and the XPS analysis of ZnO-Sb2S3 system showed the dominant presence of Sb2O3 rather than Sb2S3. Since oxidation of Sb2S3 is understood to proceed mainly from the ZnO-Sb2S3 interface, a ZnS interlayer was introduced between ZnO nanorods and Sb2S3 by chemical route. The subsequent structural and optical properties of the ZnO-ZnS-Sb2S3 system are analyzed in detail. The introduction of sulfide interlayer prevents the oxidation of Sb2S3 which is evident from reduced oxide phase in Sb2S3. Significant improvement in the structural and optical properties of Sb2S3 are reported as compared to the parent ZnO-Sb2S3 system. This gain in the optical properties of hybrid ZnO-ZnS-Sb2S3 nanostructures is explained as being related to successful prevention of Sb2O3 formation at the Sb-ZnO interface and stabilization of the desired Sb2S3.

Polymorphisms of the FTO gene are associated with variation in energy intake, but not energy expenditure.

PubMed

Speakman, John R; Rance, Kellie A; Johnstone, Alexandra M

2008-08-01

The FTO gene has significant polymorphic variation associated with obesity, but its function is unknown. We screened a population of 150 whites (103F/47M) resident in NE Scotland, United Kingdom, for variants of the FTO gene and linked these to phenotypic variation in their energy expenditure (basal metabolic rate (BMR) and maximal oxygen consumption VO(2)max) and energy intake. There was no significant association between the FTO genotype and BMR or VO(2)max. The FTO genotype was significantly associated (P = 0.024) with variation in energy intake, with average daily intake being 9.0 MJ for the wild-type TT genotype and 10.2 and 9.5 MJ for the "at risk" AT and AA genotypes, respectively. Adjusting intake for BMR did not remove the significance (P = 0.043). FTO genotype probably affects obesity via effects on food intake rather than energy expenditure.

A Synergistic Effect of Surfactant and ZrO2 Underlayer on Photocurrent Enhancement and Cathodic Shift of Nanoporous Fe2O3 Photoanode

PubMed Central

Shinde, Pravin S.; Lee, Su Yong; Choi, Sun Hee; Lee, Hyun Hwi; Ryu, Jungho; Jang, Jum Suk

2016-01-01

Augmenting the donor density and nanostructure engineering are the crucial points to improve solar water oxidation performance of hematite (α-Fe2O3). This work addresses the sluggish water oxidation reaction associated with hematite photoanode by tweaking its internal porosity. The porous hematite photoanodes are fabricated by a novel synthetic strategy via pulse reverse electrodeposition (PRED) method that involves incorporation of a cationic CTAB surfactant in a sulfate electrolyte and spin-coated ZrO2 underlayer (UL) on FTO. CTAB is found to be beneficial in promoting the film growth rate during PRED. Incorporation of Zr4+ ions from ZrO2 UL and Sn4+ ions from FTO into the Fe2O3 lattice via solid-state diffusion reaction during pertinent annihilation of surfactant molecules at 800 °C produced internally porous hematite films with improved carrier concentration. The porous hematite demonstrated a sustained photocurrent enhancement and a significant cathodic shift of 130 mV relative to the planar hematite under standard illumination conditions (AM 1.5G) in 1 M NaOH electrolyte. The absorption, electrochemical impedance spectroscopy and Mott-Schottky analyses revealed that the ZrO2 UL and CTAB not only increased the carrier density and light harvesting but also accelerated the surface oxidation reaction kinetics, synergistically boosting the performance of internally porous hematite photoanodes. PMID:27577967

Obesity-associated variants within FTO form long-range functional connections with IRX3.

PubMed

Smemo, Scott; Tena, Juan J; Kim, Kyoung-Han; Gamazon, Eric R; Sakabe, Noboru J; Gómez-Marín, Carlos; Aneas, Ivy; Credidio, Flavia L; Sobreira, Débora R; Wasserman, Nora F; Lee, Ju Hee; Puviindran, Vijitha; Tam, Davis; Shen, Michael; Son, Joe Eun; Vakili, Niki Alizadeh; Sung, Hoon-Ki; Naranjo, Silvia; Acemel, Rafael D; Manzanares, Miguel; Nagy, Andras; Cox, Nancy J; Hui, Chi-Chung; Gomez-Skarmeta, Jose Luis; Nóbrega, Marcelo A

2014-03-20

Genome-wide association studies (GWAS) have reproducibly associated variants within introns of FTO with increased risk for obesity and type 2 diabetes (T2D). Although the molecular mechanisms linking these noncoding variants with obesity are not immediately obvious, subsequent studies in mice demonstrated that FTO expression levels influence body mass and composition phenotypes. However, no direct connection between the obesity-associated variants and FTO expression or function has been made. Here we show that the obesity-associated noncoding sequences within FTO are functionally connected, at megabase distances, with the homeobox gene IRX3. The obesity-associated FTO region directly interacts with the promoters of IRX3 as well as FTO in the human, mouse and zebrafish genomes. Furthermore, long-range enhancers within this region recapitulate aspects of IRX3 expression, suggesting that the obesity-associated interval belongs to the regulatory landscape of IRX3. Consistent with this, obesity-associated single nucleotide polymorphisms are associated with expression of IRX3, but not FTO, in human brains. A direct link between IRX3 expression and regulation of body mass and composition is demonstrated by a reduction in body weight of 25 to 30% in Irx3-deficient mice, primarily through the loss of fat mass and increase in basal metabolic rate with browning of white adipose tissue. Finally, hypothalamic expression of a dominant-negative form of Irx3 reproduces the metabolic phenotypes of Irx3-deficient mice. Our data suggest that IRX3 is a functional long-range target of obesity-associated variants within FTO and represents a novel determinant of body mass and composition.

Physical activity attenuates the effect of the FTO genotype on obesity traits in European adults: The Food4Me study.

PubMed

Celis-Morales, Carlos; Marsaux, Cyril F M; Livingstone, Katherine M; Navas-Carretero, Santiago; San-Cristobal, Rodrigo; O'donovan, Clare B; Forster, Hannah; Woolhead, Clara; Fallaize, Rosalind; Macready, Anna L; Kolossa, Silvia; Hallmann, Jacqueline; Tsirigoti, Lydia; Lambrinou, Christina P; Moschonis, George; Godlewska, Magdalena; Surwiłło, Agnieszka; Grimaldi, Keith; Bouwman, Jildau; Manios, Yannis; Traczyk, Iwona; Drevon, Christian A; Parnell, Laurence D; Daniel, Hannelore; Gibney, Eileen R; Brennan, Lorraine; Walsh, Marianne C; Gibney, Mike; Lovegrove, Julie A; Martinez, J Alfredo; Saris, Wim H M; Mathers, John C

2016-04-01

To examine whether the effect of FTO loci on obesity-related traits could be modified by physical activity (PA) levels in European adults. Of 1,607 Food4Me participants randomized, 1,280 were genotyped for FTO (rs9939609) and had available PA data. PA was measured objectively using accelerometers (TracmorD, Philips), whereas anthropometric measures [BMI and waist circumference (WC)] were self-reported via the Internet. FTO genotype was associated with a higher body weight [β: 1.09 kg per risk allele, (95% CI: 0.14-2.04), P = 0.024], BMI [β: 0.54 kg m(-2) , (0.23-0.83), P < 0.0001], and WC [β: 1.07 cm, (0.24-1.90), P = 0.011]. Moderate-equivalent PA attenuated the effect of FTO on BMI (P[interaction]  = 0.020). Among inactive individuals, FTO increased BMI by 1.06 kg m(-2) per allele (P = 0.024), whereas the increase in BMI was substantially attenuated among active individuals (0.16 kg m(-2) , P = 0.388). We observed similar effects for WC (P[interaction]  = 0.005): the FTO risk allele increased WC by 2.72 cm per allele among inactive individuals but by only 0.49 cm in active individuals. PA attenuates the effect of FTO genotype on BMI and WC. This may have important public health implications because genetic susceptibility to obesity in the presence of FTO variants may be reduced by adopting a physically active lifestyle. © 2016 The Obesity Society.

FTO genotype is associated with exercise training-induced changes in body composition

PubMed Central

Rankinen, Tuomo; Rice, Treva; Teran-Garcia, Margarita; Rao, D.C.; Bouchard, Claude

2010-01-01

The fat mass and obesity associated (FTO) gene is the first obesity-susceptibility gene identified by genome-wide association scans and confirmed in several follow-up studies. Homozygotes for the risk allele (A/A) have 1.67 times greater risk of obesity than those who do not have the allele. However, it is not known if regular exercise-induced changes in body composition are influenced by the FTO genotype. The purpose of our study was to test if the FTO genotype is associated with exercise-induced changes in adiposity. Body composition was derived from underwater weighing before and after a 20-week endurance training program in 481 previously sedentary white subjects of the HERITAGE Family Study. FTO SNP rs8050136 was genotyped using Illumina GoldenGate assay. In the sedentary state, the A/A homozygotes were significantly heavier and fatter than the heterozygotes and the C/C homozygotes in men (p=0.004) but not in women (p=0.331; gene-by-sex interaction p=0.0053). The FTO genotype was associated with body fat responses to regular exercise (p<0.005; adjusted for age, sex, and baseline value of response trait): carriers of the C-allele showed three times greater fat mass and %body fat losses than the A/A homozygotes. The FTO genotype explained 2% of the variance in adiposity changes. Our data suggest that the FTO obesity-susceptibility genotype influences the body fat responses to regular exercise. Resistance to exercise-induced reduction in total adiposity may represent one mechanism by which the FTO A allele promotes overweight and obesity. PMID:19543202

FTO genetic variants, dietary intake and body mass index: insights from 177,330 individuals.

PubMed

Qi, Qibin; Kilpeläinen, Tuomas O; Downer, Mary K; Tanaka, Toshiko; Smith, Caren E; Sluijs, Ivonne; Sonestedt, Emily; Chu, Audrey Y; Renström, Frida; Lin, Xiaochen; Ängquist, Lars H; Huang, Jinyan; Liu, Zhonghua; Li, Yanping; Asif Ali, Muhammad; Xu, Min; Ahluwalia, Tarunveer Singh; Boer, Jolanda M A; Chen, Peng; Daimon, Makoto; Eriksson, Johan; Perola, Markus; Friedlander, Yechiel; Gao, Yu-Tang; Heppe, Denise H M; Holloway, John W; Houston, Denise K; Kanoni, Stavroula; Kim, Yu-Mi; Laaksonen, Maarit A; Jääskeläinen, Tiina; Lee, Nanette R; Lehtimäki, Terho; Lemaitre, Rozenn N; Lu, Wei; Luben, Robert N; Manichaikul, Ani; Männistö, Satu; Marques-Vidal, Pedro; Monda, Keri L; Ngwa, Julius S; Perusse, Louis; van Rooij, Frank J A; Xiang, Yong-Bing; Wen, Wanqing; Wojczynski, Mary K; Zhu, Jingwen; Borecki, Ingrid B; Bouchard, Claude; Cai, Qiuyin; Cooper, Cyrus; Dedoussis, George V; Deloukas, Panos; Ferrucci, Luigi; Forouhi, Nita G; Hansen, Torben; Christiansen, Lene; Hofman, Albert; Johansson, Ingegerd; Jørgensen, Torben; Karasawa, Shigeru; Khaw, Kay-Tee; Kim, Mi-Kyung; Kristiansson, Kati; Li, Huaixing; Lin, Xu; Liu, Yongmei; Lohman, Kurt K; Long, Jirong; Mikkilä, Vera; Mozaffarian, Dariush; North, Kari; Pedersen, Oluf; Raitakari, Olli; Rissanen, Harri; Tuomilehto, Jaakko; van der Schouw, Yvonne T; Uitterlinden, André G; Zillikens, M Carola; Franco, Oscar H; Shyong Tai, E; Ou Shu, Xiao; Siscovick, David S; Toft, Ulla; Verschuren, W M Monique; Vollenweider, Peter; Wareham, Nicholas J; Witteman, Jacqueline C M; Zheng, Wei; Ridker, Paul M; Kang, Jae H; Liang, Liming; Jensen, Majken K; Curhan, Gary C; Pasquale, Louis R; Hunter, David J; Mohlke, Karen L; Uusitupa, Matti; Cupples, L Adrienne; Rankinen, Tuomo; Orho-Melander, Marju; Wang, Tao; Chasman, Daniel I; Franks, Paul W; Sørensen, Thorkild I A; Hu, Frank B; Loos, Ruth J F; Nettleton, Jennifer A; Qi, Lu

2014-12-20

FTO is the strongest known genetic susceptibility locus for obesity. Experimental studies in animals suggest the potential roles of FTO in regulating food intake. The interactive relation among FTO variants, dietary intake and body mass index (BMI) is complex and results from previous often small-scale studies in humans are highly inconsistent. We performed large-scale analyses based on data from 177,330 adults (154 439 Whites, 5776 African Americans and 17 115 Asians) from 40 studies to examine: (i) the association between the FTO-rs9939609 variant (or a proxy single-nucleotide polymorphism) and total energy and macronutrient intake and (ii) the interaction between the FTO variant and dietary intake on BMI. The minor allele (A-allele) of the FTO-rs9939609 variant was associated with higher BMI in Whites (effect per allele = 0.34 [0.31, 0.37] kg/m(2), P = 1.9 × 10(-105)), and all participants (0.30 [0.30, 0.35] kg/m(2), P = 3.6 × 10(-107)). The BMI-increasing allele of the FTO variant showed a significant association with higher dietary protein intake (effect per allele = 0.08 [0.06, 0.10] %, P = 2.4 × 10(-16)), and relative weak associations with lower total energy intake (-6.4 [-10.1, -2.6] kcal/day, P = 0.001) and lower dietary carbohydrate intake (-0.07 [-0.11, -0.02] %, P = 0.004). The associations with protein (P = 7.5 × 10(-9)) and total energy (P = 0.002) were attenuated but remained significant after adjustment for BMI. We did not find significant interactions between the FTO variant and dietary intake of total energy, protein, carbohydrate or fat on BMI. Our findings suggest a positive association between the BMI-increasing allele of FTO variant and higher dietary protein intake and offer insight into potential link between FTO, dietary protein intake and adiposity. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Impact of Variation at the FTO Locus on Milk Fat Yield in Holstein Dairy Cattle

PubMed Central

Zielke, Lea G.; Bortfeldt, Ralf H.; Reissmann, Monika; Tetens, Jens; Thaller, Georg; Brockmann, Gudrun A.

2013-01-01

This study explores the biological role of the Fat Mass and Obesity associated (FTO) gene locus on milk composition in German Holstein cattle. Since FTO controls energy homeostasis and expenditure and the FTO locus has repeatedly shown association with obesity in human studies, we tested FTO as a candidate gene in particular for milk fat yield, which represents a high amount of energy secreted during lactation. The study was performed on 2,402 bulls and 860 cows where dense milk composition data were available. Genetic information was taken from a 2 Mb region around FTO. Five SNPs and two haplotype blocks in a 725 kb region covering FTO and the neighboring genes RPGRIP1L, U6ATAC, and 5 S rRNA were associated with milk fat yield and also affected protein yield in the same direction. Interestingly, higher frequency SNP alleles and haplotypes within the FTO gene increased milk fat and protein yields by up to 2.8 and 2.2 kg per lactation, respectively, while the most frequent haplotype in the upstream block covering exon 1 of FTO to exon 15 of RPGRIP1L had opposite effects with lower fat and milk yield. Both haplotype blocks were also significant in cows. The loci accounted for about 1% of the corresponding trait variance in the population. The association signals not only provided evidence for at least two causative mutations in the FTO locus with a functional effect on milk but also milk protein yield. The pleiotropic effects suggest a biological function on the usage of energy resources and the control of energy balance rather than directly affecting fat and protein synthesis. The identified effect of the obesity gene locus on milk energy content suggests an impact on infant nutrition by breast feeding in humans. PMID:23691044

Impact of variation at the FTO locus on milk fat yield in Holstein dairy cattle.

PubMed

Zielke, Lea G; Bortfeldt, Ralf H; Reissmann, Monika; Tetens, Jens; Thaller, Georg; Brockmann, Gudrun A

2013-01-01

This study explores the biological role of the Fat Mass and Obesity associated (FTO) gene locus on milk composition in German Holstein cattle. Since FTO controls energy homeostasis and expenditure and the FTO locus has repeatedly shown association with obesity in human studies, we tested FTO as a candidate gene in particular for milk fat yield, which represents a high amount of energy secreted during lactation. The study was performed on 2,402 bulls and 860 cows where dense milk composition data were available. Genetic information was taken from a 2 Mb region around FTO. Five SNPs and two haplotype blocks in a 725 kb region covering FTO and the neighboring genes RPGRIP1L, U6ATAC, and 5 S rRNA were associated with milk fat yield and also affected protein yield in the same direction. Interestingly, higher frequency SNP alleles and haplotypes within the FTO gene increased milk fat and protein yields by up to 2.8 and 2.2 kg per lactation, respectively, while the most frequent haplotype in the upstream block covering exon 1 of FTO to exon 15 of RPGRIP1L had opposite effects with lower fat and milk yield. Both haplotype blocks were also significant in cows. The loci accounted for about 1% of the corresponding trait variance in the population. The association signals not only provided evidence for at least two causative mutations in the FTO locus with a functional effect on milk but also milk protein yield. The pleiotropic effects suggest a biological function on the usage of energy resources and the control of energy balance rather than directly affecting fat and protein synthesis. The identified effect of the obesity gene locus on milk energy content suggests an impact on infant nutrition by breast feeding in humans.

Study of Electrocatalytic Properties of Metal–Organic Framework PCN-223 for the Oxygen Reduction Reaction

DOE PAGES

Usov, Pavel M.; Huffman, Brittany; Epley, Charity C.; ...

2017-03-27

Here, a highly robust metal–organic framework (MOF) constructed from Zr 6 oxo clusters and Fe(III) porphyrin linkers, PCN-223-Fe was investigated as a heterogeneous catalyst for oxygen reduction reaction (ORR). Films of the framework were grown on a conductive FTO substrate and showed a high catalytic current upon application of cathodic potentials and achieved high H 2O/H 2O 2 selectivity. In addition, the effect of the proton source on the catalytic performance was also investigated.

Electrical properties of CZTS thin films

NASA Astrophysics Data System (ADS)

Rao, M. C.; Kumar, M. Seshu; Lakshmi, K.; Rao, K. Koteswara; Parimala, M. P. D.; Basha, S. K. Shahenoor

2018-05-01

CZTS (Cu2ZnSnS4) thin films have been coated on to FTO and MO glass substrates by single step electro deposition process. Different characterization techniques were performed on to the prepared samples such as DSC and Raman studies. The Phase transition and weight loss of the precursors can be measured by DSC analysis. Raman spectrum is used to identify the functional groups and chemical structure involved in the materials. Electrical measurements confirm the nature of the film and also depend on the charge concentration present in the samples.

A haplotype of three SNPs in FTO had a strong association with body composition and BMI in Iranian male adolescents.

PubMed

Kalantari, Naser; Keshavarz Mohammadi, Nastaran; Izadi, Pantea; Doaei, Saeid; Gholamalizadeh, Maryam; Eini-Zinab, Hassan; Salonurmi, Tuire; Rafieifar, Shahram; Janipoor, Reza; Azizi Tabesh, Ghasem

2018-01-01

Single-nucleotide polymorphisms (SNPs), which are located in the first intron of the FTO gene, are reported to be associated with body weight and the body mass index (BMI). However, their effects on anthropometric measurements in adolescents are poorly understood. This study aimed to investigate the association of three adjacent polymorphisms (rs9930506, rs9930501, & rs9932754) in the FTO gene with anthropometric indices in Iranian adolescent males. The participants comprised a total of 237 adolescent males who were recruited randomly from two high schools in Tehran, Iran. The DNA samples were genotyped for the FTO gene polymorphisms by DNA sequencing. BMI, body fat percentage (BF%), and body muscle percentage (BM%) were determined using a validated bioelectrical impedance analysis scale. The association of the FTO polymorphisms with weight, height, BMI, BF%, and BM% was investigated. A haplotype of rs9930506, rs9930501, and rs9932754 (GGT) in the first intron of the FTO with complete linkage disequilibrium (LD) was found to be significantly associated with higher weight (OR = 1.32), BMI (OR = 5.36) and BF% (OR = 1.46), and lower BM% (OR = 3.59) (all P<0.001). None of the students with GGC genotypes were underweight, while all of the students with AAT genotypes had high muscle mass. A haplotype in the first intron of the FTO gene had a strong association with obesity indices in Iranian adolescent males. The FTO gene polymorphisms might have greater effects on anthropometric indices than what was previously imagined. Moreover, we suggested that the FTO gene exerted their effects on anthropometric measurements through haplotypes (and not single SNPs).

FTO Is Associated with Aortic Valve Stenosis in a Gender Specific Manner of Heterozygote Advantage: A Population-Based Case-Control Study.

PubMed

Thron, Cindy; Akhyari, Payam; Godehardt, Erhard; Lichtenberg, Artur; Rüther, Ulrich; Seehaus, Stefanie

2015-01-01

Single nucleotide polymorphisms (SNPs) within the Fat mass and obesity associated (FTO) gene have been linked with increased body weight. However, the data on an association of FTO with cardiovascular diseases remains conflicting. Therefore, we ascertained whether FTO is associated with aortic valve stenosis (AVS), one of the most frequent cardiovascular diseases in the Western world. In this population-based case-control study the FTO SNP rs9939609 was analyzed in 300 German patients with AVS and 429 German controls of the KORA survey S4, representing a random population. Blood samples were collected prior to aortic valve replacement in AVS cases and FTO rs9939609 was genotyped via ARMS-PCR. Genotype frequencies differed significantly between AVS cases and KORA controls (p = 0.004). Separate gender-analyses uncovered an association of FTO with AVS exclusively in males; homozygote carriers for the risk-allele (A) had a higher risk to develop AVS (p = 0.017, odds ratio (OR) 1.727; 95% confidence interval (CI) 1.087-2.747, recessive model), whereas heterozygote carriers for the risk-allele showed a lower risk (p = 0.002, OR 0.565, 95% CI 0.384-0.828, overdominant model). After adjustment for multiple co-variables, the odds ratios of heterozygotes remained significant for an association with AVS (p = 0.008, OR 0.565, 95% CI 0.369-0.861). This study revealed an association of FTO rs9939609 with AVS. Furthermore, this association was restricted to men, with heterozygotes having a significantly lower chance to develop AVS. Lastly, the association between FTO and AVS was independent of BMI and other variables such as diabetes mellitus.

FTO Is Associated with Aortic Valve Stenosis in a Gender Specific Manner of Heterozygote Advantage: A Population-Based Case-Control Study

PubMed Central

Thron, Cindy; Akhyari, Payam; Godehardt, Erhard; Lichtenberg, Artur; Rüther, Ulrich; Seehaus, Stefanie

2015-01-01

Background Single nucleotide polymorphisms (SNPs) within the Fat mass and obesity associated (FTO) gene have been linked with increased body weight. However, the data on an association of FTO with cardiovascular diseases remains conflicting. Therefore, we ascertained whether FTO is associated with aortic valve stenosis (AVS), one of the most frequent cardiovascular diseases in the Western world. Methods and Findings In this population-based case-control study the FTO SNP rs9939609 was analyzed in 300 German patients with AVS and 429 German controls of the KORA survey S4, representing a random population. Blood samples were collected prior to aortic valve replacement in AVS cases and FTO rs9939609 was genotyped via ARMS-PCR. Genotype frequencies differed significantly between AVS cases and KORA controls (p = 0.004). Separate gender-analyses uncovered an association of FTO with AVS exclusively in males; homozygote carriers for the risk-allele (A) had a higher risk to develop AVS (p = 0.017, odds ratio (OR) 1.727; 95% confidence interval (CI) 1.087–2.747, recessive model), whereas heterozygote carriers for the risk-allele showed a lower risk (p = 0.002, OR 0.565, 95% CI 0.384–0.828, overdominant model). After adjustment for multiple co-variables, the odds ratios of heterozygotes remained significant for an association with AVS (p = 0.008, OR 0.565, 95% CI 0.369–0.861). Conclusions This study revealed an association of FTO rs9939609 with AVS. Furthermore, this association was restricted to men, with heterozygotes having a significantly lower chance to develop AVS. Lastly, the association between FTO and AVS was independent of BMI and other variables such as diabetes mellitus. PMID:26431034

Fabrication and investigation of the optoelectrical properties of MoS2/CdS heterojunction solar cells

PubMed Central

2014-01-01

Molybdenum disulfide (MoS2)/cadmium sulfide (CdS) heterojunction solar cells were successfully synthesized via chemical bath deposition (CBD) and chemical vapor deposition (CVD). The as-grown CdS film on a fluorine tin oxide (FTO) substrate deposited by CBD is continuous and compact. The MoS2 film deposited by CVD is homogeneous and continuous, with a uniform color and a thickness of approximately 10 nm. The optical absorption range of the MoS2/CdS heterojunction covers the visible and near-infrared spectral regions of 350 to 800 nm, which is beneficial for the improvement of solar cell efficiency. Moreover, the MoS2/CdS solar cell exhibits good current-voltage (I-V) characteristics and pronounced photovoltaic behavior, with an open-circuit voltage of 0.66 V and a short-circuit current density of 0.227 × 10-6 A/cm2, comparable to the results obtained from other MoS2-based solar cells. This research is critical to investigate more efficient and stable solar cells based on graphene-like materials in the future. PMID:25593552

Revelation of rutile phase by Raman scattering for enhanced photoelectrochemical performance of hydrothermally-grown anatase TiO2 film

NASA Astrophysics Data System (ADS)

Cho, Hsun-Wei; Liao, Kuo-Lun; Yang, Jih-Sheng; Wu, Jih-Jen

2018-05-01

Photoelectrochemical (PEC) performances of the anatase TiO2 films hydrothermally grown on the seeded fluorine-doped tin oxide (FTO) substrates are examined in this work. Structural characterizations of the TiO2 films were conducted using Raman scattering spectroscopy. Although there is no obvious rutile peak appearing, an asymmetrical peak centered at ∼399 cm-1 was observed in the Raman spectra of the TiO2 films deposited either on the low-temperature-formed seed layers or with low concentrations of Ti precursor. The asymmetrical Raman shift can be deconvoluted into the B1g mode of anatase and Eg mode of rutile TiO2 peaks centered at ∼399 cm-1 and ∼447 cm-1, respectively. Therefore, a minute quantity of rutile phase was inspected in the anatase film using Raman scattering spectroscopy. With the same light harvesting ability, we found that the PEC performance of the anatase TiO2 film was significantly enhanced as the minute quantity of rutile phase existing in the film. It is ascribed to the formation of the anatase/rutile heterojunction which is beneficial to the charge separation in the photoanode.

In situ synthesis of CdS/CdWO4/WO3 heterojunction films with enhanced photoelectrochemical properties

NASA Astrophysics Data System (ADS)

Zhan, Faqi; Li, Jie; Li, Wenzhang; Yang, Yahui; Liu, Wenhua; Li, Yaomin

2016-09-01

CdS/CdWO4/WO3 heterojunction films on fluorine-doped tin oxide (FTO) substrates are for the first time prepared as an efficient photoanode for photoelectrochemical (PEC) hydrogen generation by an in situ conversion process. The samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), ultraviolet visible spectrometry (UV-vis) and X-ray photoelectron spectroscopy (XPS). The CdS hollow spheres (∼80 nm) sensitized WO3 plate film with a CdWO4 buffer-layer exhibits increased visible light absorption and a significantly improved photoelectrochemical performance. The photocurrent density at 0 V (vs. Ag/AgCl) of the CdS/CdWO4/WO3 anode is ∼3 times higher than that of the CdWO4/WO3 anode, and ∼9 times higher than that of pure WO3 under illumination. The highest incident-photon-to-current-efficiency (IPCE) value increased from 16% to 63% when the ternary heterojunction was formed. This study demonstrates that the synthesis of ternary composite photocatalysts by the in situ conversion process may be a promising approach to achieve high photoelectric conversion efficiency.

Effect of annealing process on the heterostructure CuO/Cu2O as a highly efficient photocathode for photoelectrochemical water reduction

NASA Astrophysics Data System (ADS)

Du, Fan; Chen, Qing-Yun; Wang, Yun-Hai

2017-05-01

CuO/Cu2O photocathodes were successfully prepared via simply annealing the electrodeposited Cu2O on fluoride doped tin oxide (FTO) substrate. They were characterized by X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscope (TEM), UV-vis absorption spectra and X-ray photoelectron spectroscopy (XPS). The results showed that the heterojunction of CuO/Cu2O was formed during the annealing process and presented the nature of p-type semiconductor. The photocurrent density and photoelectrochemical (PEC) stability of the p-type heterostructure CuO/Cu2O photocathode was improved greatly compared with the pure Cu2O, which was greatly affected by annealing time and temperature. The highest photo current density of -0.451 mA/cm2 and highest stability was obtained via annealing at 650 °C for 15 min (at -0.3 V vs. Ag/AgCl), which gave a remarkable improvement than the as-deposited Cu2O (-0.08 mA/cm2). This suggested that the CuO/Cu2O heterojunction facilitated the electron-hole pair separation and improved the photocathode's current and stability.

Two-step electrodeposition to fabricate the p-n heterojunction of a Cu2O/BiVO4 photoanode for the enhancement of photoelectrochemical water splitting.

PubMed

Bai, Shouli; Liu, Jingchao; Cui, Meng; Luo, Ruixian; He, Jing; Chen, Aifan

2018-05-15

A Cu2O/BiVO4 p-n heterojunction based photoanode in photoelectrochemical (PEC) water splitting is fabricated by a two-step electrodeposition method on an FTO substrate followed by annealing treatment. The structures and properties of the samples are characterized by XRD, FESEM, HRTEM, XPS and UV-visible spectra. The photoelectrochemical activity of the photoanode in water oxidation has been investigated and measured in a three electrode quartz cell system; the obtained maximum photocurrent density of 1.72 mA cm-2 at 1.23 V vs. RHE is 4.5 times higher than that of pristine BiVO4 thin films (∼0.38 mA cm-2). The heterojunction based photoanode also exhibits a tremendous cathodic shift of the onset potential (∼420 mV) and enhancement in the IPCE value by more than 4-fold. The enhanced photoelectrochemical properties of the Cu2O/BiVO4 photoelectrode are attributed to the efficient separation of the photoexcited electron-hole pairs caused by the inner electronic field (IEF) of the p-n heterojunction.

Preparation and characterization of electrodeposited SnS:In thin films: Effect of In dopant.

PubMed

Kafashan, Hosein; Balak, Zohre

2017-09-05

SnS:In thin films were grown on fluorine doped tin oxide (FTO) substrate by cathodic electrodeposition technique. The solution was containing 2mM SnCl 2 and 16mM Na 2 S 2 O 3 and different amounts of 1mM InCl 3 as In-dopant. The pH, bath temperature, deposition time, and deposition potential (E) were fixed at 2.1, 60°C, 30min, and -1V, respectively. The XRD results showed that the synthesized films were polycrystalline orthorhombic SnS. The XPS results demonstrated that the films were composed of Sn, S and In. According to the FESEM images, an increase in In-dopant concentration leads to a change in morphology from grain-like to sheet-like having a nanoscale thickness of 20-80nm and fiber-like. The PL spectra of undoped SnS exhibited four emission peaks including a UV peak, two blue emission peaks, and an IR emission peak. According to the UV-Vis spectra, the direct band gap of SnS:In thin films was estimated to be 1.40-1.66eV. Copyright © 2017 Elsevier B.V. All rights reserved.

Preparation and characterization of electrodeposited SnS:In thin films: Effect of In dopant

NASA Astrophysics Data System (ADS)

Kafashan, Hosein; Balak, Zohre

2017-09-01

SnS:In thin films were grown on fluorine doped tin oxide (FTO) substrate by cathodic electrodeposition technique. The solution was containing 2 mM SnCl2 and 16 mM Na2S2O3 and different amounts of 1 mM InCl3 as In-dopant. The pH, bath temperature, deposition time, and deposition potential (E) were fixed at 2.1, 60 °C, 30 min, and - 1 V, respectively. The XRD results showed that the synthesized films were polycrystalline orthorhombic SnS. The XPS results demonstrated that the films were composed of Sn, S and In. According to the FESEM images, an increase in In-dopant concentration leads to a change in morphology from grain-like to sheet-like having a nanoscale thickness of 20-80 nm and fiber-like. The PL spectra of undoped SnS exhibited four emission peaks including a UV peak, two blue emission peaks, and an IR emission peak. According to the UV-Vis spectra, the direct band gap of SnS:In thin films was estimated to be 1.40-1.66 eV.

Electrochemical synthesis of nanostructured Se-doped SnS: Effect of Se-dopant on surface characterizations

NASA Astrophysics Data System (ADS)

Kafashan, Hosein; Azizieh, Mahdi; Balak, Zohre

2017-07-01

SnS1-xSex nanostructures with different Se-dopant concentrations were deposited on fluorine doped tin oxide (FTO) substrate through cathodic electrodeposition technique. The pH, temperature, applied potential (E), and deposition time remained were 2.1, 60 °C, -1 V, and 30 min, respectively. SnS1-xSex nanostructures were characterized using X-ray diffraction (XRD), field emission scanning electron microcopy (FESEM), energy dispersive X-ray spectroscopy (EDX), room temperature photoluminescence (PL), and UV-vis spectroscopy. The XRD patterns revealed that the SnS1-xSex nanostructures were polycrystalline with orthorhombic structure. FESEM showed various kinds of morphologies in SnS1-xSex nanostructures due to Se-doping. PL and UV-vis spectroscopy were used to evaluate the optical properties of SnS1-xSex thin films. The PL spectra of SnS1-xSex nanostructures displayed four emission peaks, those are a blue, a green, an orange, and a red emission. UV-vis spectra showed that the optical band gap energy (Eg) of SnS1-xSex nanostructures varied between 1.22-1.65 eV, due to Se-doping.

Macronutrients and the FTO gene expression in hypothalamus; a systematic review of experimental studies.

PubMed

Doaei, Saeid; Kalantari, Naser; Mohammadi, Nastaran Keshavarz; Tabesh, Ghasem Azizi; Gholamalizadeh, Maryam

The various studies have examined the relationship between FTO gene expression and macronutrients levels. In order to obtain better viewpoint from this interactions, all of existing studies were reviewed systematically. All published papers have been obtained and reviewed using standard and sensitive keywords from databases such as CINAHL, Embase, PubMed, PsycInfo, and the Cochrane, from 1990 to 2016. The results indicated that all of 6 studies that met the inclusion criteria (from a total of 428 published article) found FTO gene expression changes at short-term follow-ups. Four of six studies found an increased FTO gene expression after calorie restriction, while two of them indicated decreased FTO gene expression. The effect of protein, carbohydrate and fat were separately assessed and suggested by all of six studies. In Conclusion, The level of FTO gene expression in hypothalamus is related to macronutrients levels. Future research should evaluate the long-term impact of dietary interventions. Copyright © 2017. Published by Elsevier B.V.

Optimization of active cell area on the dye-sensitized solar cell efficiency

NASA Astrophysics Data System (ADS)

Putri, A. W.; Nurosyid, F.; Supriyanto, Agus

2017-11-01

This study is aimed to obtain optimal active area producing high efficiency of DSSC module. The DSSC structure is constructed of TiO2 as working electrode, dye as photosensitizer, platinum as counter electrode, and electrolyte as electron transfer media. TiO2 paste was deposited on Fluorine-doped Tin Oxide (FTO) by screen printing method. Meanwhile, platinum was also coated on FTO via brush painting method. Keithley I-V meter was performed to characterize DSSC electrical property. The active area of each cell was varied of 4.5 cm2, 9 cm2, and 13.5 cm2. Each cell was assembled into a module using an external series connection of Z type. The module was consisted of 12 cells, 6 cells, and 4 cells with module active area of 54 cm2. The optimal active area of DSSC cell is 4.5 cm2 resulting 0.4149% efficiency. In addition, the highest efficiency of DSSC module is 0.2234% acquired by 6 cells assembling.

The bigger picture of FTO – the first GWAS-identified obesity gene

PubMed Central

Loos, Ruth J.F.; Yeo, Giles S.H.

2014-01-01

In 2007, SNPs that cluster in the first intron of FTO showed highly significant association in the first two genome-wide association studies for obesity traits of which the minor allele increases body mass index (BMI) by 0.39 kg/m2 (or 1,130 g in body weight) and risk of obesity by 1.20 fold. Subsequent studies convincingly confirmed this association across populations of diverse ancestry and throughout the life course, with the largest effect seen in young adulthood. The effect of FTO SNPs on obesity traits in African and Asian ancestry populations is similar or somewhat smaller than in European ancestry populations, but the BMI-increasing allele is substantially less prevalent in non-European ancestry populations. FTO SNPs do not influence physical activity levels, yet, in physically active individuals, FTO’s effect on obesity susceptibility is attenuated by ~30%. Growing evidence from epidemiological and functional studies suggests that FTO confers an increased risk of obesity through subtle changes in food intake and preference. In addition, recent emerging data now points to a role for FTO in the sensing of nutrients and the regulation of translation and growth. In this review, we explore the genetic epidemiology of FTO and discuss how its complex biology might link to the regulation of body weight. PMID:24247219

TiO2 nanocrystals decorated Z-schemed core-shell CdS-CdO nanorod arrays as high efficiency anodes for photoelectrochemical hydrogen generation.

PubMed

Li, Chia-Hsun; Hsu, Chan-Wei; Lu, Shih-Yuan

2018-07-01

TiO 2 nanocrystals decorated core-shell CdS-CdO nanorod arrays, TiO 2 @CdO/CdS NR, were fabricated as high efficiency anodes for photoelctrochemical hydrogen generation. The novel sandwich heterostructure was constructed from first growth of CdS nanorod arrays on a fluorine doped tin oxide (FTO) substrate with a hydrothermal process, followed by in situ generation of CdO thin films of single digit nanometers from the CdS nanorod surfaces through thermal oxidation, and final decoration of TiO 2 nanocrystals of 10-20 nm via a successive ionic layer absorption and reaction process. The core-shell CdS-CdO heterostructure possesses a Z-scheme band structure to enhance interfacial charge transfer, facilitating effective charge separation to suppress electron-hole recombination within CdS for much improved current density generation. The final decoration of TiO 2 nanocrystals passivates surface defects and trap states of CdO, further suppressing surface charge recombination for even higher photovoltaic conversion efficiencies. The photoelectrochemical performances of the plain CdS nanorod array were significantly improved with the formation of the sandwich heterostructure, achieving a photo current density of 3.2 mA/cm 2 at 1.23 V (vs. RHE), a 141% improvement over the plain CdS nanorod array and a 32% improvement over the CdO/CdS nanorod array. Copyright © 2018 Elsevier Inc. All rights reserved.

Electrical and optical performance of transparent conducting oxide films deposited by electrostatic spray assisted vapour deposition.

PubMed

Hou, Xianghui; Choy, Kwang-Leong; Liu, Jun-Peng

2011-09-01

Transparent conducting oxide (TCO) films have the remarkable combination of high electrical conductivity and optical transparency. There is always a strong motivation to produce TCO films with good performance at low cost. Electrostatic Spray Assisted Vapor Deposition (ESAVD), as a variant of chemical vapour deposition (CVD), is a non-vacuum and low-cost deposition method. Several types of TCO films have been deposited using ESAVD process, including indium tin oxide (ITO), antimony-doped tin oxide (ATO), and fluorine doped tin oxide (FTO). This paper reports the electrical and optical properties of TCO films produced by ESAVD methods, as well as the effects of post treatment by plasma hydrogenation on these TCO films. The possible mechanisms involved during plasma hydrogenation of TCO films are also discussed. Reduction and etching effect during plasma hydrogenation are the most important factors which determine the optical and electrical performance of TCO films.

BiVO4/WO3/SnO2 Double-Heterojunction Photoanode with Enhanced Charge Separation and Visible-Transparency for Bias-Free Solar Water-Splitting with a Perovskite Solar Cell.

PubMed

Baek, Ji Hyun; Kim, Byeong Jo; Han, Gill Sang; Hwang, Sung Won; Kim, Dong Rip; Cho, In Sun; Jung, Hyun Suk

2017-01-18

Coupling dissimilar oxides in heterostructures allows the engineering of interfacial, optical, charge separation/transport and transfer properties of photoanodes for photoelectrochemical (PEC) water splitting. Here, we demonstrate a double-heterojunction concept based on a BiVO 4 /WO 3 /SnO 2 triple-layer planar heterojunction (TPH) photoanode, which shows simultaneous improvements in the charge transport (∼93% at 1.23 V vs RHE) and transmittance at longer wavelengths (>500 nm). The TPH photoanode was prepared by a facile solution method: a porous SnO 2 film was first deposited on a fluorine-doped tin oxide (FTO)/glass substrate followed by WO 3 deposition, leading to the formation of a double layer of dense WO 3 and a WO 3 /SnO 2 mixture at the bottom. Subsequently, a BiVO 4 nanoparticle film was deposited by spin coating. Importantly, the WO 3 /(WO 3 +SnO 2 ) composite bottom layer forms a disordered heterojunction, enabling intimate contact, lower interfacial resistance, and efficient charge transport/transfer. In addition, the top BiVO 4 /WO 3 heterojunction layer improves light absorption and charge separation. The resultant TPH photoanode shows greatly improved internal quantum efficiency (∼80%) and PEC water oxidation performance (∼3.1 mA/cm 2 at 1.23 V vs RHE) compared to the previously reported BiVO 4 /WO 3 photoanodes. The PEC performance was further improved by a reactive-ion etching treatment and CoO x electrocatalyst deposition. Finally, we demonstrated a bias-free and stable solar water-splitting by constructing a tandem PEC device with a perovskite solar cell (STH ∼3.5%).

Facile synthesis of bismuth oxyhalide nanosheet films with distinct conduction type and photo-induced charge carrier behavior

NASA Astrophysics Data System (ADS)

Jia, Huimin; He, Weiwei; Zhang, Beibei; Yao, Lei; Yang, Xiaokai; Zheng, Zhi

2018-05-01

A modified successive ionic layer adsorption and reaction (SILAR) method was developed to fabricate 2D ordered BiOX (X = CI, Br, I) nanosheet array films on FTO substrates at room temperature. The formation of BiOX films were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), UV-vis absorption spectroscopy, and X-ray photoelectron spectroscopy (XPS). The semiconductor surface states determine the type of semiconductor. Although BiOCI, BiOBr and BiOI belong to the bismuth oxyhalide semiconductor family and possess similar crystal and electronic structures, they show different conductivity types due to their respective surface states. Mott-Schottky curve results demonstrate that the BiOCl and BiOI nanosheet arrays display n-type semiconductor properties, while the BiOBr films exhibit p-type semiconductor properties. Assisted by surface photovoltage (SPV) and transient photovoltage (TPV) techniques, the photoinduced charge transfer dynamics on the surface/interface of the BiOX/FTO nanosheet films were systematically and comparatively investigated. As revealed by the results, both the separation and transfer dynamics of the photo-induced carrier are influenced by film thickness.

Structure-based design and evaluation of novel N-phenyl-1H-indol-2-amine derivatives for fat mass and obesity-associated (FTO) protein inhibition.

PubMed

Padariya, Monikaben; Kalathiya, Umesh

2016-10-01

Fat mass and obesity-associated (FTO) protein contributes to non-syndromic human obesity which refers to excessive fat accumulation in human body and results in health risk. FTO protein has become a promising target for anti-obesity medicines as there is an immense need for the rational design of potent inhibitors to treat obesity. In our study, a new scaffold N-phenyl-1H-indol-2-amine was selected as a base for FTO protein inhibitors by applying scaffold hopping approach. Using this novel scaffold, different derivatives were designed by extending scaffold structure with potential functional groups. Molecular docking simulations were carried out by using two different docking algorithm implemented in CDOCKER (flexible docking) and AutoDock programs (rigid docking). Analyzing results of rigid and flexible docking, compound MU06 was selected based on different properties and predicted binding affinities for further analysis. Molecular dynamics simulation of FTO/MU06 complex was performed to characterize structure rationale and binding stability. Certainly, Arg96 and His231 residue of FTO protein showed stable interaction with inhibitor MU06 throughout the production dynamics phase. Three residues of FTO protein (Arg96, Asp233, and His231) were found common in making H-bond interactions with MU06 during molecular dynamics simulation and CDOCKER docking. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fat mass- and obesity-associated genotype, dietary intakes and anthropometric measures in European adults: the Food4Me study.

PubMed

Livingstone, Katherine M; Celis-Morales, Carlos; Navas-Carretero, Santiago; San-Cristobal, Rodrigo; Forster, Hannah; O'Donovan, Clare B; Woolhead, Clara; Marsaux, Cyril F M; Macready, Anna L; Fallaize, Rosalind; Kolossa, Silvia; Tsirigoti, Lydia; Lambrinou, Christina P; Moschonis, George; Godlewska, Magdalena; Surwiłło, Agnieszka; Drevon, Christian A; Manios, Yannis; Traczyk, Iwona; Gibney, Eileen R; Brennan, Lorraine; Walsh, Marianne C; Lovegrove, Julie A; Martinez, J Alfredo; Saris, Wim H M; Daniel, Hannelore; Gibney, Mike; Mathers, John C

2016-02-14

The interplay between the fat mass- and obesity-associated (FTO) gene variants and diet has been implicated in the development of obesity. The aim of the present analysis was to investigate associations between FTO genotype, dietary intakes and anthropometrics among European adults. Participants in the Food4Me randomised controlled trial were genotyped for FTO genotype (rs9939609) and their dietary intakes, and diet quality scores (Healthy Eating Index and PREDIMED-based Mediterranean diet score) were estimated from FFQ. Relationships between FTO genotype, diet and anthropometrics (weight, waist circumference (WC) and BMI) were evaluated at baseline. European adults with the FTO risk genotype had greater WC (AA v. TT: +1·4 cm; P=0·003) and BMI (+0·9 kg/m2; P=0·001) than individuals with no risk alleles. Subjects with the lowest fried food consumption and two copies of the FTO risk variant had on average 1·4 kg/m2 greater BMI (Ptrend=0·028) and 3·1 cm greater WC (Ptrend=0·045) compared with individuals with no copies of the risk allele and with the lowest fried food consumption. However, there was no evidence of interactions between FTO genotype and dietary intakes on BMI and WC, and thus further research is required to confirm or refute these findings.

m6A demethylase FTO facilitates tumor progression in lung squamous cell carcinoma by regulating MZF1 expression.

PubMed

Liu, Jiqin; Ren, Dangli; Du, Zhenhua; Wang, Hekong; Zhang, Hua; Jin, Ying

2018-08-25

N 6 -Methyladenosine (m 6 A) represents the most prevalent internal modification in mammalian mRNAs. Emerging evidences suggest that m 6 A modification is profoundly implicated in many biological processes, including cancer development. However, limited knowledge is available about the functional importance of m 6 A in lung cancer. In this study, by data mining The Cancer Genome Atlas (TCGA) database, we first identified fat mass- and obesity-associated protein (FTO) as a prognostic factor for lung squamous cell carcinoma (LUSC). Then we showed that FTO, but not other m 6 A modification genes including METTL3, METTL14 and ALKBH5, was the major dysregulated factor responsible for aberrant m 6 A modification in LUSC. Loss-of-function studies suggested that FTO knockdown effectively inhibited cell proliferation and invasion, while promoted cell apoptosis of L78 and NCI-H520 cells. Furthermore, overexpression of FTO, but not its mutant form, facilitated the malignant phenotypes of CHLH-1 cells. Mechanistically, FTO enhanced MZF1 expression by reducing m 6 A levels and mRNA stability in MZF1 mRNA transcript, leading to oncogenic functions. Taken together, our study demonstrates the functional importance of FTO in the tumor progression of LUSC and provides a potential therapeutic target for LUSC treatment. Copyright © 2018 Elsevier Inc. All rights reserved.

Patching compliance with full-time vs. part-time occlusion therapy.

PubMed

Kane, Jessica; Biernacki, Ron; Fraine, Lisa; Fukuda, Neva; Haskins, Kelsie; Morrison, David G

2013-01-01

Amblyopia is commonly treated with part-time occlusion (PTO) therapy. We have made two anecdotal observations regarding this therapy. First, children undergoing full-time occlusion seem to have better success and compliance rates. Secondly, a subset of children exists that fail PTO but can improve with more aggressive therapy. A retrospective review where treatment, visual outcome, and compliance scores were recorded. Compliance was graded on percent adherence reported by family. Patients scored “1” (for no compliance), “2” (for 1–25% of prescribed treatment performed), “3” (for 26–50%), “4” (for 51–75%), or “5” (for 76–100%). Seventy-six children were enrolled in the study: forty-five were treated with part-time occlusion, twenty-two were treated with full time occlusion (FTO), and nine had a history of failed PTO and were subsequently treated with FTO. Visual outcomes for FTO versus PTO were not statistically significant (P = 0.82). However, compliance rates in FTO were significantly better (P = 0.02). Of the nine patients that failed PTO, four improved an average of three lines with full-time occlusion, and five had no change with more aggressive patching. This study confirms previous reports of similar visual outcomes between PTO and FTO. However, compliance rates for FTO seem to be higher and some children who have failed PTO may improve with FTO.

A Strategy to Enhance the Efficiency of Quantum Dot-Sensitized Solar Cells by Decreasing Electron Recombination with Polyoxometalate/TiO2 as the Electronic Interface Layer.

PubMed

Chen, Li; Chen, Weilin; Li, Jianping; Wang, Jiabo; Wang, Enbo

2017-07-21

Electron recombination occurring at the TiO 2 /quantum dot sensitizer/electrolyte interface is the key reason for hindering further efficiency improvements to quantum dot sensitized solar cells (QDSCs). Polyoxometalate (POM) can act as an electron-transfer medium to decrease electron recombination in a photoelectric device owing to its excellent oxidation/reduction properties and thermostability. A POM/TiO 2 electronic interface layer prepared by a simple layer-by-layer self-assembly method was added between fluorine-doped tin oxide (FTO) and mesoporous TiO 2 in the photoanode of QDSCs, and the effect on the photovoltaic performance was systematically investigated. Photovoltaic experimental results and the electron transmission mechanism show that the POM/TiO 2 electronic interface layer in the QDSCs can clearly suppress electron recombination, increase the electron lifetime, and result in smoother electron transmission. In summary, the best conversion efficiency of QDSCs with POM/TiO 2 electronic interface layers increases to 8.02 %, which is an improvement of 25.1 % compared with QDSCs without POM/TiO 2 . This work first builds an electron-transfer bridge between FTO and the quantum dot sensitizer and paves the way for further improved efficiency of QDSCs. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

FTO genotype, physical activity, and coronary heart disease risk in Swedish men and women.

PubMed

Gustavsson, Jaana; Mehlig, Kirsten; Leander, Karin; Lissner, Lauren; Björck, Lena; Rosengren, Annika; Nyberg, Fredrik

2014-04-01

Variants in the fat mass- and obesity-associated gene (FTO) predisposing to obesity and diabetes mellitus have also been associated with cardiovascular disease. Physical activity has been suggested to attenuate the FTO effect on obesity, but it is unknown whether this is also true for cardiovascular disease. Therefore, we explored whether physical activity modifies the FTO association with coronary heart disease (CHD). FTO rs9939609 (T>A) polymorphism was genotyped in 2 Swedish population-based case-control studies with 1743 CHD cases and 4402 population controls (25-74 years of age; 41% women). Leisure time physical activity was assessed by questionnaires, and 3 levels were defined: low, medium, and high. Overall, carriers of the FTO A allele had an increased risk of CHD (odds ratio, 1.20; 95% confidence interval, 1.06-1.37) adjusted for age, sex, study, and body mass index. Although A-allele carriers with low physical activity had the highest CHD risk (odds ratio, 3.30; 95% confidence interval, 2.44-4.46) compared with those with TT genotype and high activity, the effects of FTO genotype and physical activity on CHD risk were approximately additive, indicating the absence of additive interaction. The stratum-specific relative risks of CHD from the A allele in subjects with low, medium, and high physical activity were odds ratio 1.11 (95% confidence interval, 0.77-1.60), 1.22 (1.04-1.44), and 1.38 (1.06-1.80), respectively, but the suggested multiplicative interaction was not significant. FTO rs9939609 A-allele carriers have an increased CHD risk, and the association is not counteracted by increased physical activity.

Fat mass-and obesity-associated (FTO) gene variant is associated with obesity: longitudinal analyses in two cohort studies and functional test.

PubMed

Qi, Lu; Kang, Kihwa; Zhang, Cuilin; van Dam, Rob M; Kraft, Peter; Hunter, David; Lee, Chih-Hao; Hu, Frank B

2008-11-01

To examine the longitudinal association of fat mass-and obesity-associated (FTO) variant with obesity, circulating adipokine levels, and FTO expression in various materials from human and mouse. We genotyped rs9939609 in 2,287 men and 3,520 women from two prospective cohorts. Plasma adiponectin and leptin were measured in a subset of diabetic men (n = 854) and women (n = 987). Expression of FTO was tested in adipocytes from db/db mice and mouse macrophages. We observed a trend toward decreasing associations between rs9939609 and BMI at older age (>or=65 years) in men, whereas the associations were constant across different age groups in women. In addition, the single nucleotide polymorphism (SNP) rs9939609 was associated with lower plasma adiponectin (log[e]--means, 1.82 +/- 0.04, 1.73 +/- 0.03, and 1.68 +/- 0.05 for TT, TA, and AA genotypes, respectively; P for trend = 0.02) and leptin (log[e]--means, 3.56 +/- 0.04, 3.63 +/- 0.04, and 3.70 +/- 0.06; P for trend = 0.06) in diabetic women. Adjustment for BMI attenuated the associations. FTO gene was universally expressed in human and mice tissues, including adipocytes. In an ancillary study of adipocytes from db/db mice, FTO expression was approximately 50% lower than in those from wild-type mice. The association between FTO SNP rs9939609 and obesity risk may decline at older age. The variant affects circulating adiponectin and leptin levels through the changes in BMI. In addition, the expression of FTO gene was reduced in adipocytes from db/db mice.

FTO promotes SREBP1c maturation and enhances CIDEC transcription during lipid accumulation in HepG2 cells.

PubMed

Chen, Ao; Chen, Xiaodong; Cheng, Shiqiang; Shu, Le; Yan, Meiping; Yao, Lun; Wang, Binyu; Huang, Shuguang; Zhou, Lei; Yang, Zaiqing; Liu, Guoquan

2018-05-01

The fat mass and obesity-associated (FTO) gene is tightly related to body weight and fat mass, and plays a pivotal role in regulating lipid accumulation in hepatocytes. However, the mechanisms underlying its function are poorly understood. Sterol regulatory element binding protein-1c (SREBP1c) is a transcription factor that regulates lipogenesis. Cell death-inducing DFFA (DNA fragmentation factor-α)-like effector c (CIDEC) plays a crucial role in lipid droplets (LDs) size controlling and lipid accumulation. In this report, we first observed that FTO overexpression in HepG2 cells resulted in an increase of lipogenesis and up-regulation of SREBP1c and CIDEC, two key regulatory factors in lipogenesis. In contrast, FTO knockdown in HepG2 cells resulted in a decrease of lipogenesis and down-regulation of SREBP1c and CIDEC expression. Moreover, SREBP1c knockdown resulted in a decrease of lipogenesis in HepG2 cells with FTO overexpression. In addition, FTO demethylation defect mutant presented less transcription of the key genes, and less nuclear translocation and maturation of SREBP1c. Further investigation demonstrated that overexpression of SREBP1c in HepG2 cells also promoted high CIDEC expression. Luciferase reporter assays showed that SREBP1c significantly stimulated CIDEC gene promoter activity. Finally, CIDEC knockdown reduced SREBP1c-induced lipogenesis. In conclusion, our studies suggest that FTO increased the lipid accumulation in hepatocytes by increasing nuclear translocation of SREBP1c and SREBP1c maturation, thus improving the transcriptional activity of LD-associated protein CIDEC. Our studies may provide new mechanistic insight into nonalcoholic fatty liver disease (NAFLD) mediated by FTO. Copyright © 2018 The Authors. Published by Elsevier B.V. All rights reserved.

Macronutrient intake as a mediator with FTO to increase body mass index.

PubMed

Hardy, Dale S; Racette, Susan B; Hoelscher, Deanna M

2014-01-01

The fat mass and obesity-associated (FTO) single nucleotide polymorphisms (SNPs; rs1421085, rs17817449, rs9939609, rs8050136) and macronutrient intake (carbohydrate, protein, fat, total calories) are associated with body mass index (BMI). However, the mechanism for this relationship has not been fully elucidated. This study examined whether macronutrient intake mediates the association between FTO SNPs and BMI. Baseline cross-sectional data from the Atherosclerosis Risk in Communities (ARIC) study of whites (n = 10,176) and African Americans (n = 3641) aged 45 to 64 years were analyzed. In linear regression models with BMI as the dependent variable, FTO SNPs were significantly associated with higher BMI after adjusting for covariates. The addition of energy-adjusted macronutrients attenuated the FTO effect estimates, indicating partial mediation. In whites, β ranged from 0.40 (95% confidence interval [CI], 0.20, 0.60) for rs17817449 heterozygous carriers to 0.93 (95% CI, 0.64, 122) for rs8050136 homozygous carriers; for African Americans rs17817449 homozygous carriers β was 0.65 (95% CI, 0.03, 1.27). In models with macronutrient intake as the dependent variable, all FTO SNPs were associated with higher protein intake for homozygous carriers after adjusting for BMI and other covariates. Among whites, β ranged from 1.44 (95% CI, 0.51, 2.37) for rs8050136 to 1.73 (95% CI, 0.85, 2.61) for rs17817449; among African American rs8050136 homozygous carriers β was 2.46 (95% CI, 0.77, 4.14). In mediation analysis, in whites only, FTO high-risk alleles were associated with higher BMI partly through their small effects on carbohydrate and protein intake. These findings suggest that in adults, the relationship between FTO variants and BMI is not primarily through mediation of food intake.

Associations of variants in FTO and near MC4R with obesity traits in South Asian Indians.

PubMed

Vasan, Senthil K; Fall, Tove; Neville, Matthew J; Antonisamy, Belavendra; Fall, Caroline H; Geethanjali, Finney S; Gu, Harvest F; Raghupathy, Palany; Samuel, Prasanna; Thomas, Nihal; Brismar, Kerstin; Ingelsson, Erik; Karpe, Fredrik

2012-11-01

Recent genome-wide association studies show that loci in FTO and melanocortin 4 receptor (MC4R) associate with obesity-related traits. Outside Western populations the associations between these variants have not always been consistent and in Indians it has been suggested that FTO relates to diabetes without an obvious intermediary obesity phenotype. We investigated the association between genetic variants in FTO (rs9939609) and near MC4R (rs17782313) with obesity- and type 2 diabetes (T2DM)-related traits in a longitudinal birth cohort of 2,151 healthy individuals from the Vellore birth cohort in South India. The FTO locus displayed significant associations with several conventional obesity-related anthropometric traits. The per allele increase is about 1% for BMI, waist circumference (WC), hip circumference (HC), and waist-hip ratio. Consistent associations were observed for adipose tissue-specific measurements such as skinfold thickness reinforcing the association with obesity-related traits. Obesity associations for the MC4R locus were weak or nonsignificant but a signal for height (P < 0.001) was observed. The effect on obesity-related traits for FTO was seen in adulthood, but not at younger ages. The loci also showed nominal associations with increased blood glucose but these associations were lost on BMI adjustment. The effect of FTO on obesity-related traits was driven by an urban environmental influence. We conclude that rs9939609 variant in the FTO locus is associated with measures of adiposity and metabolic consequences in South Indians with an enhanced effect associated with urban living. The detection of these associations in Indians is challenging because conventional anthropometric obesity measures work poorly in the Indian "thin-fat" phenotype.

Variation in the fat mass and obesity-related (FTO) genotype is not associated with body fatness in infants, but possibly with their length.

PubMed

Henriksson, P; Löf, M; Söderkvist, P; Forsum, E

2014-10-01

Data relating variation at the fat mass and obesity-related (FTO) locus (rs9939609) to fat mass in infancy are inconclusive. To study relationships between FTO genotype and infant size (at 1 and 12 weeks and at 1 year of age) and body composition (at 1 and 12 weeks). Body composition was assessed using air displacement plethysmography in 207 infants. FTO was genotyped using the TaqMan assay. The number of risk alleles was related to length at 1 and 12 weeks (P = 0.007-0.033) but not to fat mass. The relationship to length was stronger in boys than in girls. Our results suggest that the FTO genotype is not related during infancy to fat mass but is related to length in boys but not in girls. © 2014 The Authors. Pediatric Obesity © 2014 World Obesity.

Changes in Physical Activity Following a Genetic-Based Internet-Delivered Personalized Intervention: Randomized Controlled Trial (Food4Me)

PubMed Central

Livingstone, Katherine M; Fallaize, Rosalind; Kolossa, Silvia; Hallmann, Jacqueline; San-Cristobal, Rodrigo; Navas-Carretero, Santiago; O'Donovan, Clare B; Woolhead, Clara; Forster, Hannah; Moschonis, George; Lambrinou, Christina-Paulina; Surwillo, Agnieszka; Godlewska, Magdalena; Hoonhout, Jettie; Goris, Annelies; Macready, Anna L; Walsh, Marianne C; Gibney, Eileen R; Brennan, Lorraine; Manios, Yannis; Traczyk, Iwona; Drevon, Christian A; Lovegrove, Julie A; Martinez, J Alfredo; Daniel, Hannelore; Gibney, Michael J; Mathers, John C; Saris, Wim HM

2016-01-01

Background There is evidence that physical activity (PA) can attenuate the influence of the fat mass- and obesity-associated (FTO) genotype on the risk to develop obesity. However, whether providing personalized information on FTO genotype leads to changes in PA is unknown. Objective The purpose of this study was to determine if disclosing FTO risk had an impact on change in PA following a 6-month intervention. Methods The single nucleotide polymorphism (SNP) rs9939609 in the FTO gene was genotyped in 1279 participants of the Food4Me study, a four-arm, Web-based randomized controlled trial (RCT) in 7 European countries on the effects of personalized advice on nutrition and PA. PA was measured objectively using a TracmorD accelerometer and was self-reported using the Baecke questionnaire at baseline and 6 months. Differences in baseline PA variables between risk (AA and AT genotypes) and nonrisk (TT genotype) carriers were tested using multiple linear regression. Impact of FTO risk disclosure on PA change at 6 months was assessed among participants with inadequate PA, by including an interaction term in the model: disclosure (yes/no) × FTO risk (yes/no). Results At baseline, data on PA were available for 874 and 405 participants with the risk and nonrisk FTO genotypes, respectively. There were no significant differences in objectively measured or self-reported baseline PA between risk and nonrisk carriers. A total of 807 (72.05%) of the participants out of 1120 in the personalized groups were encouraged to increase PA at baseline. Knowledge of FTO risk had no impact on PA in either risk or nonrisk carriers after the 6-month intervention. Attrition was higher in nonrisk participants for whom genotype was disclosed (P=.01) compared with their at-risk counterparts. Conclusions No association between baseline PA and FTO risk genotype was observed. There was no added benefit of disclosing FTO risk on changes in PA in this personalized intervention. Further RCT studies are warranted to confirm whether disclosure of nonrisk genetic test results has adverse effects on engagement in behavior change. Trial Registration ClinicalTrials.gov NCT01530139; http://clinicaltrials.gov/show/NCT01530139 (Archived by WebCite at: http://www.webcitation.org/6XII1QwHz) PMID:26851191

Changes in Physical Activity Following a Genetic-Based Internet-Delivered Personalized Intervention: Randomized Controlled Trial (Food4Me).

PubMed

Marsaux, Cyril F M; Celis-Morales, Carlos; Livingstone, Katherine M; Fallaize, Rosalind; Kolossa, Silvia; Hallmann, Jacqueline; San-Cristobal, Rodrigo; Navas-Carretero, Santiago; O'Donovan, Clare B; Woolhead, Clara; Forster, Hannah; Moschonis, George; Lambrinou, Christina-Paulina; Surwillo, Agnieszka; Godlewska, Magdalena; Hoonhout, Jettie; Goris, Annelies; Macready, Anna L; Walsh, Marianne C; Gibney, Eileen R; Brennan, Lorraine; Manios, Yannis; Traczyk, Iwona; Drevon, Christian A; Lovegrove, Julie A; Martinez, J Alfredo; Daniel, Hannelore; Gibney, Michael J; Mathers, John C; Saris, Wim H M

2016-02-05

There is evidence that physical activity (PA) can attenuate the influence of the fat mass- and obesity-associated (FTO) genotype on the risk to develop obesity. However, whether providing personalized information on FTO genotype leads to changes in PA is unknown. The purpose of this study was to determine if disclosing FTO risk had an impact on change in PA following a 6-month intervention. The single nucleotide polymorphism (SNP) rs9939609 in the FTO gene was genotyped in 1279 participants of the Food4Me study, a four-arm, Web-based randomized controlled trial (RCT) in 7 European countries on the effects of personalized advice on nutrition and PA. PA was measured objectively using a TracmorD accelerometer and was self-reported using the Baecke questionnaire at baseline and 6 months. Differences in baseline PA variables between risk (AA and AT genotypes) and nonrisk (TT genotype) carriers were tested using multiple linear regression. Impact of FTO risk disclosure on PA change at 6 months was assessed among participants with inadequate PA, by including an interaction term in the model: disclosure (yes/no) × FTO risk (yes/no). At baseline, data on PA were available for 874 and 405 participants with the risk and nonrisk FTO genotypes, respectively. There were no significant differences in objectively measured or self-reported baseline PA between risk and nonrisk carriers. A total of 807 (72.05%) of the participants out of 1120 in the personalized groups were encouraged to increase PA at baseline. Knowledge of FTO risk had no impact on PA in either risk or nonrisk carriers after the 6-month intervention. Attrition was higher in nonrisk participants for whom genotype was disclosed (P=.01) compared with their at-risk counterparts. No association between baseline PA and FTO risk genotype was observed. There was no added benefit of disclosing FTO risk on changes in PA in this personalized intervention. Further RCT studies are warranted to confirm whether disclosure of nonrisk genetic test results has adverse effects on engagement in behavior change. ClinicalTrials.gov NCT01530139; http://clinicaltrials.gov/show/NCT01530139 (Archived by WebCite at: http://www.webcitation.org/6XII1QwHz).

Genomic variants in the FTO gene are associated with sporadic amyotrophic lateral sclerosis in Greek patients.

PubMed

Mitropoulos, Konstantinos; Merkouri Papadima, Eleni; Xiromerisiou, Georgia; Balasopoulou, Angeliki; Charalampidou, Kyriaki; Galani, Vasiliki; Zafeiri, Krystallia-Vassiliki; Dardiotis, Efthymios; Ralli, Styliani; Deretzi, Georgia; John, Anne; Kydonopoulou, Kyriaki; Papadopoulou, Elpida; di Pardo, Alba; Akcimen, Fulya; Loizedda, Annalisa; Dobričić, Valerija; Novaković, Ivana; Kostić, Vladimir S; Mizzi, Clint; Peters, Brock A; Basak, Nazli; Orrù, Sandro; Kiskinis, Evangelos; Cooper, David N; Gerou, Spyridon; Drmanac, Radoje; Bartsakoulia, Marina; Tsermpini, Evangelia-Eirini; Hadjigeorgiou, Georgios M; Ali, Bassam R; Katsila, Theodora; Patrinos, George P

2017-12-08

Amyotrophic lateral sclerosis (ALS) is a devastating disease whose complex pathology has been associated with a strong genetic component in the context of both familial and sporadic disease. Herein, we adopted a next-generation sequencing approach to Greek patients suffering from sporadic ALS (together with their healthy counterparts) in order to explore further the genetic basis of sporadic ALS (sALS). Whole-genome sequencing analysis of Greek sALS patients revealed a positive association between FTO and TBC1D1 gene variants and sALS. Further, linkage disequilibrium analyses were suggestive of a specific disease-associated haplotype for FTO gene variants. Genotyping for these variants was performed in Greek, Sardinian, and Turkish sALS patients. A lack of association between FTO and TBC1D1 variants and sALS in patients of Sardinian and Turkish descent may suggest a founder effect in the Greek population. FTO was found to be highly expressed in motor neurons, while in silico analyses predicted an impact on FTO and TBC1D1 mRNA splicing for the genomic variants in question. To our knowledge, this is the first study to present a possible association between FTO gene variants and the genetic etiology of sALS. In addition, the next-generation sequencing-based genomics approach coupled with the two-step validation strategy described herein has the potential to be applied to other types of human complex genetic disorders in order to identify variants of clinical significance.

FTO Obesity Risk Variants Are Linked to Adipocyte IRX3 Expression and BMI of Children - Relevance of FTO Variants to Defend Body Weight in Lean Children?

PubMed Central

Landgraf, Kathrin; Scholz, Markus; Kovacs, Peter; Kiess, Wieland; Körner, Antje

2016-01-01

Background Genome-wide association studies have identified variants within the FTO (fat mass and obesity associated) locus as the strongest predictors of obesity amongst all obesity-associated gene loci. Recent evidence suggests that variants in FTO directly affect human adipocyte function through targeting IRX3 and IRX5 and thermogenesis regulation. Aim We addressed the relevance of this proposed FTO-IRX pathway in adipose tissue (AT) of children. Results Expression of IRX3 was higher in adipocytes compared to SVF. We found increased adipocyte-specific expression of IRX3 and IRX5 with the presence of the FTO risk haplotype in lean children, whereas it was unaffected by risk variants in obese peers. We further show that IRX3 expression was elevated in isolated adipocytes and AT of lean compared to obese children, particularly in UCP1-negative adipocytes, and inversely correlated with BMI SDS. Independent of BMI, IRX3 expression in adipocytes was significantly related to adipocyte hypertrophy, and subsequent associations with AT inflammation and HOMA-IR in the children. Conclusion One interpretation of our observation of FTO risk variants linked to IRX3 expression and adipocyte size restricted to lean children, along with the decreased IRX3 expression in obese compared to lean peers, may reflect a defense mechanism for protecting body-weight, which is pertinent for lean children. PMID:27560134

Fabrication of Co3O4 mesoporous thin films by using cobalt/chitosan precursor on fluorine-doped tin oxide glass

NASA Astrophysics Data System (ADS)

Yang, Hui-Chia; Tsai, Jung-Che

2017-06-01

For the development of high-performance and low-cost electrode materials, many alternative materials have been fabricated by various groups. Among these materials, Co3O4 has been demonstrated to be a promising candidate for pseudocapacitors because of its low potential environmental pollution, low cost, and extremely high theoretical specific capacitance. Chitosan, a linear polysaccharide produced by the deacetylation of chitin, is a nontoxic, tissue-compatible polymeric biomaterial. It is usually used to eliminate or filter the heavy metals in wastewater. That is, chitosan can act as a deliverer of metal ions and a nanostructure constructer of metals (or metal oxides). In this study, a facile approach is developed to synthesize mesoporous cobalt oxide thin films on fluorine-doped tin oxide (FTO)-coated glass with environmentally friendly chitosan, which chelates cobalt ions.

Statistical and biological gene-lifestyle interactions of MC4R and FTO with diet and physical activity on obesity: new effects on alcohol consumption

USDA-ARS?s Scientific Manuscript database

Fat mass and obesity (FTO) and melanocortin-4 receptor (MC4R) and are relevant genes associated with obesity. This could be through food intake, but results are contradictory. Modulation by diet or other lifestyle factors is also not well understood. To investigate whether MC4R and FTO associations ...

Ti Porous Film-Supported NiCo₂S₄ Nanotubes Counter Electrode for Quantum-Dot-Sensitized Solar Cells.

PubMed

Deng, Jianping; Wang, Minqiang; Song, Xiaohui; Yang, Zhi; Yuan, Zhaolin

2018-04-17

In this paper, a novel Ti porous film-supported NiCo₂S₄ nanotube was fabricated by the acid etching and two-step hydrothermal method and then used as a counter electrode in a CdS/CdSe quantum-dot-sensitized solar cell. Measurements of the cyclic voltammetry, Tafel polarization curves, and electrochemical impedance spectroscopy of the symmetric cells revealed that compared with the conventional FTO (fluorine doped tin oxide)/Pt counter electrode, Ti porous film-supported NiCo₂S₄ nanotubes counter electrode exhibited greater electrocatalytic activity toward polysulfide electrolyte and lower charge-transfer resistance at the interface between electrolyte and counter electrode, which remarkably improved the fill factor, short-circuit current density, and power conversion efficiency of the quantum-dot-sensitized solar cell. Under illumination of one sun (100 mW/cm²), the quantum-dot-sensitized solar cell based on Ti porous film-supported NiCo₂S₄ nanotubes counter electrode achieved a power conversion efficiency of 3.14%, which is superior to the cell based on FTO/Pt counter electrode (1.3%).

Investigation of porosity and heterojunction effects of a mesoporous hematite electrode on photoelectrochemical water splitting.

PubMed

Liu, Jingling; Shahid, Muhammad; Ko, Young-Seon; Kim, Eunchul; Ahn, Tae Kyu; Park, Jong Hyeok; Kwon, Young-Uk

2013-06-28

In this paper, we report the porosity and heterojunction effects of hematite (α-Fe2O3) on the photoelectrochemical (PEC) water splitting properties. The worm-like mesoporous hematite thin films (MHFs) with a pore size of ~9 nm and a wall thickness of ~5 nm were successfully obtained through the self-assembly process. MHFs formed on FTO showed much better PEC properties than those of nonporous hematite thin films (NP-HF) owing to the suppression of charge recombination. The PEC data of MHFs under front and back illumination conditions indicated that the porous structure allows the diffusion of electrolyte deep inside the MHF increasing the number of holes to be utilized in the water oxidation reaction. A heterojunction structure was formed by introducing a thin layer of SnO2 (~15 nm in thickness) between the MHF and FTO for a dramatically enhanced PEC response, which is attributed to the efficient electron transfer. Our spectroscopic and electrochemical data show that the SnO2 layer functions as an efficient electron transmitter, but does not affect the recombination kinetics of MHFs.

Photovoltaic Rudorffites: Lead-Free Silver Bismuth Halides Alternative to Hybrid Lead Halide Perovskites.

PubMed

Turkevych, Ivan; Kazaoui, Said; Ito, Eisuke; Urano, Toshiyuki; Yamada, Koji; Tomiyasu, Hiroshi; Yamagishi, Hideo; Kondo, Michio; Aramaki, Shinji

2017-10-09

Hybrid CPbX 3 (C: Cs, CH 3 NH 3 ; X: Br, I) perovskites possess excellent photovoltaic properties but are highly toxic, which hinders their practical application. Unfortunately, all Pb-free alternatives based on Sn and Ge are extremely unstable. Although stable and non-toxic C 2 ABX 6 double perovskites based on alternating corner-shared AX 6 and BX 6 octahedra (A=Ag, Cu; B=Bi, Sb) are possible, they have indirect and wide band gaps of over 2 eV. However, is it necessary to keep the corner-shared perovskite structure to retain good photovoltaic properties? Here, we demonstrate another family of photovoltaic halides based on edge-shared AX 6 and BX 6 octahedra with the general formula A a B b X x (x=a+3 b) such as Ag 3 BiI 6 , Ag 2 BiI 5 , AgBiI 4 , AgBi 2 I 7 . As perovskites were named after their prototype oxide CaTiO 3 discovered by Lev Perovski, we propose to name these new ABX halides as rudorffites after Walter Rüdorff, who discovered their prototype oxide NaVO 2 . We studied structural and optoelectronic properties of several highly stable and promising Ag-Bi-I photovoltaic rudorffites that feature direct band gaps in the range of 1.79-1.83 eV and demonstrated a proof-of-concept FTO/c-m-TiO 2 /Ag 3 BiI 6 /PTAA/Au (FTO: fluorine-doped tin oxide, PTAA: poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine], c: compact, m: mesoporous) solar cell with photoconversion efficiency of 4.3 %. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Solution-processed all-oxide bulk heterojunction solar cells based on CuO nanaorod array and TiO2 nanocrystals.

PubMed

Wu, Fan; Qiao, Qiquan; Bahrami, Behzad; Chen, Ke; Pathak, Rajesh; Tong, Yanhua; Li, Xiaoyi; Zhang, Tiansheng; Jian, Ronghua

2018-05-25

We present a method to synthesize CuO nanorod array/TiO 2 nanocrystals bulk heterojunction (BHJ) on fluorine-tin-oxide (FTO) glass, in which single-crystalline p-type semiconductor of the CuO nanorod array is grown on the FTO glass by hydrothermal reaction and the n-type semiconductor of the TiO 2 precursor is filled into the CuO nanorods to form well-organized nano-interpenetrating BHJ after air annealing. The interface charge transfer in CuO nanorod array/TiO 2 heterojunction is studied by Kelvin probe force microscopy (KPFM). KPFM results demonstrate that the CuO nanorod array/TiO 2 heterojunction can realize the transfer of photo-generated electrons from the CuO nanorod array to TiO 2 . In this work, a solar cell with the structure FTO/CuO nanoarray/TiO 2 /Al is successfully fabricated, which exhibits an open-circuit voltage (V oc ) of 0.20 V and short-circuit current density (J sc ) of 0.026 mA cm -2 under AM 1.5 illumination. KPFM studies indicate that the very low performance is caused by an undesirable interface charge transfer. The interfacial surface potential (SP) shows that the electron concentration in the CuO nanorod array changes considerably after illumination due to increased photo-generated electrons, but the change in the electron concentration in TiO 2 is much less than in CuO, which indicates that the injection efficiency of the photo-generated electrons from CuO to TiO 2 is not satisfactory, resulting in an undesirable J sc in the solar cell. The interface photovoltage from the KPFM measurement shows that the low V oc results from the small interfacial SP difference between CuO and TiO 2 because the low injected electron concentration cannot raise the Fermi level significantly in TiO 2 . This conclusion agrees with the measured work function results under illumination. Hence, improvement of the interfacial electron injection is primary for the CuO nanorod array/TiO 2 heterojunction solar cells.

Solution-processed all-oxide bulk heterojunction solar cells based on CuO nanaorod array and TiO2 nanocrystals

NASA Astrophysics Data System (ADS)

Wu, Fan; Qiao, Qiquan; Bahrami, Behzad; Chen, Ke; Pathak, Rajesh; Tong, Yanhua; Li, Xiaoyi; Zhang, Tiansheng; Jian, Ronghua

2018-05-01

We present a method to synthesize CuO nanorod array/TiO2 nanocrystals bulk heterojunction (BHJ) on fluorine-tin-oxide (FTO) glass, in which single-crystalline p-type semiconductor of the CuO nanorod array is grown on the FTO glass by hydrothermal reaction and the n-type semiconductor of the TiO2 precursor is filled into the CuO nanorods to form well-organized nano-interpenetrating BHJ after air annealing. The interface charge transfer in CuO nanorod array/TiO2 heterojunction is studied by Kelvin probe force microscopy (KPFM). KPFM results demonstrate that the CuO nanorod array/TiO2 heterojunction can realize the transfer of photo-generated electrons from the CuO nanorod array to TiO2. In this work, a solar cell with the structure FTO/CuO nanoarray/TiO2/Al is successfully fabricated, which exhibits an open-circuit voltage (V oc) of 0.20 V and short-circuit current density (J sc) of 0.026 mA cm‑2 under AM 1.5 illumination. KPFM studies indicate that the very low performance is caused by an undesirable interface charge transfer. The interfacial surface potential (SP) shows that the electron concentration in the CuO nanorod array changes considerably after illumination due to increased photo-generated electrons, but the change in the electron concentration in TiO2 is much less than in CuO, which indicates that the injection efficiency of the photo-generated electrons from CuO to TiO2 is not satisfactory, resulting in an undesirable J sc in the solar cell. The interface photovoltage from the KPFM measurement shows that the low V oc results from the small interfacial SP difference between CuO and TiO2 because the low injected electron concentration cannot raise the Fermi level significantly in TiO2. This conclusion agrees with the measured work function results under illumination. Hence, improvement of the interfacial electron injection is primary for the CuO nanorod array/TiO2 heterojunction solar cells.

Effect of FTO rs9939609 variant on insulin resistance in obese female adolescents.

PubMed

Iskandar, Kristy; Patria, Suryono Yudha; Huriyati, Emy; Luglio, Harry Freitag; Julia, Madarina; Susilowati, Rina

2018-05-15

FTO rs9939609 variant has been shown to be associated with insulin resistance in Caucasian children. However, studies in Asia show inconsistent findings. We investigated the association between FTO rs9939609 polymorphisms and insulin resistance in obese female adolescents in Indonesia, a genetically distinct group within Asia. A total of 78 obese female adolescents participated in this study. The risk allele (A) frequency of FTO rs9939609 variant in Indonesian obese female adolescence was 44.2%. The frequency of insulin resistance was higher in the subjects with AA (54.6%) or AT (59.6%) than the subject with TT genotype (50%), but did not statistically different (p = 0.81 and p = 0.47, respectively). The insulin resistance rate was also higher in the risk allele (A) than the non-risk allele (T) subjects (0.58 vs. 0.55), but did not statistically different (p = 0.75). There was no association between FTO rs9939609 variant and body mass index, fasting glucose level, fasting insulin level, homeostatic model assessment of insulin resistance, and waist circumference (p > 0.05). In conclusion, FTO rs9939609 variant may not be associated with insulin resistance in Indonesian obese female adolescents. A multicenter study with a larger sample size is needed to clarify these findings.

Preparation of Co3O4 conical nanotube and its application in calcium ion biosensor

NASA Astrophysics Data System (ADS)

Yuan, Hongwen; Ma, Chi; Geng, Junlong; Zhang, Liqiang; Cui, Hai; Liu, Cunzhi

2018-02-01

Calcium ion (Ca2+) is an important ion involved in body life activities, and its content detection in biomedical field owns great significance. In this study, we fabricated Co3O4 conical nanotube on F-doped tin oxide (FTO) substrate for detecting Ca2+. Co3O4 is fabricated through a hydrothermal method and demonstrates a regular hexagon structure, with a length of 5-10 μm and wall thickness of 30 nm. The structure and morphology of Co3O4 were characterized by X-ray diffraction (XRD), scanning electron microscope, and transmission electron microscopy, respectively. In addition, then, we used electrochemical technique to characterize the Ca2+ concentration in the simulated body fluid. The detection of Ca2+ is originated from the electrochemical reaction of hydrogen peroxide using Co3O4 as a catalyst, in which Ca2+ plays a significant role for accelerating the decomposition of hydrogen peroxide catalytic performance. By monitoring the electron transfer signals changes during the electrochemical reaction, we can quickly quantify the Ca2+ concentrations. It is found that this Ca2+ sensor owns a wide detection range (0.1-1.1 mM), a low detection limit (3.767 μM), and good anti-interference ability.

UV radiation and CH4 gas detection with a single ZnO:Pd nanowire

NASA Astrophysics Data System (ADS)

Lupan, O.; Adelung, R.; Postica, V.; Ababii, N.; Chow, L.; Viana, B.; Pauporté, T.

2017-02-01

There is an increasing demand for sensors to monitor environmental levels of ultraviolet (UV) radiation and pollutant gases. In this work, an individual nanowire of Pd modified ZnO nanowire (ZnO:Pd NW) was integrated in a nanosensor device for efficient and fast detection of UV light and CH4 gas at room temperature. Crystalline ZnO:Pd nanowire/nanorod arrays were synthesized onto fluorine doped tin oxide (FTO) substrates by electrochemical deposition (ECD) at relative low-temperatures (90 °C) with different concentrations of PdCl2 in electrolyte solution and investigated by SEM and EDX. Nanodevices were fabricated using dual beam focused electron/ion beam (FIB/SEM) system and showed improved UV radiation response compared to pristine ZnO NW, reported previously by our group. The UV response was increased by one order in magnitude (≈ 11) for ZnO:Pd NW. Gas sensing measurements demonstrated a higher gas response and rapidity to methane (CH4 gas, 100 ppm) at room temperature, showing promising results for multifunctional applications. Also, due to miniature size and ultra-low power consumption of these sensors, it is possible to integrate them into portable devices easily, such as smartphones, digital clock, flame detection, missile lunching and other smart devices.

Alternate current conductivity in BSb films prepared by PLD technique: Electron transport processes in low-temperature range (10-275 K)

NASA Astrophysics Data System (ADS)

Das, Shirsendu; Bhunia, Ritamay; Hussain, Shamima; Bhar, Radhaballabh; Kumar Pal, Arun

2017-04-01

This study is focused on the measurement of alternate current (a.c.) electrical conductivity of BSb films, deposited on fluorine-doped tin oxide (FTO)-coated glass substrates at 673K by the pulsed laser deposition (PLD) technique. The frequency-dependent a.c. conductivity is measured as a function of temperature (10-275K) and frequency (100Hz-100kHz). The transport processes governing the electrical conduction processes in this material are analyzed critically. It is observed from FESEM micrograph that the film is composed of small discrete grain with sizes varying in the range 6-12nm. It is interesting to notice from \\lnσ_ac versus 1000/T plot that there are three distinct zones: i) Semiconductor zone at high temperature from 275 to 150K, ii) Insulator zone at low temperature from 70 to 10K and iii) an abrupt change of the \\lnσ_ac versus 1000/T plot at ˜ 75 indicating MIS transition occurring in this BSb film. We found that the activation energy for the BSb films in the lower-temperature range was quite low ˜ 6 to 41neV, while that in the higher-temperature range was 20 to 50meV.

Electrochemical properties of thin films of V2O5 doped with TiO2

NASA Astrophysics Data System (ADS)

Moura, E. A.; Cholant, C. M.; Balboni, R. D. C.; Westphal, T. M.; Lemos, R. M. J.; Azevedo, C. F.; Gündel, A.; Flores, W. H.; Gomez, J. A.; Ely, F.; Pawlicka, A.; Avellaneda, C. O.

2018-08-01

The paper presents a systematic study of the electrochromic properties of thin films of V2O5:TiO2 for a possible utilization as counter-electrode in electrochromic devices. The V2O5:TiO2 thin films were prepared by the sol-gel process and deposited on a substrate of fluorine-tin oxide transparent electrode (FTO) using the dip coating technique and heat treatment at 350 °C for 30 min. The films were characterized by chronocoulometry, cyclic voltammetry (CV), UV-Vis, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), atomic force microscopy (AFM), profilometry, and X-ray diffraction (XRD). The best results were obtained for the film of V2O5 with 7.5 mol% of TiO2, which presented highest ion storage capacity of ∼106 mC cm-2 and redox reversibility of 1. The diffusion of the Li+ ions into the thin films was modeled by solving Fick equations with appropriate boundary conditions for a plane sheet geometry. Besides that, these films showed optical modulation of 35% at 633 nm after coloration and bleaching. The XRD patterns revealed that the films have an orthorhombic crystal structure; the AFM and the profilometry confirmed roughness and thickness of 16.76 and 617 nm, respectively.

Optical Properties of Cu2O Electrodeposited on FTO Substrates: Effects of Cl Concentration

NASA Astrophysics Data System (ADS)

Bouderbala, Ibrahim Yaacoub; Herbadji, Abdelmadjid; Mentar, Loubna; Beniaiche, Abdelkrim; Azizi, Amor

2018-03-01

In this study, cuprous oxide (Cu2O) nanostructures were deposited via electrochemical route from aqueous solution containing different concentrations of copper chloride (CuCl2). The effect of chloride (Cl- ) ions on structural and optical properties was studied. Photocurrent results show that the type of conduction of these nanostructures is affected by adding Cl- ions and changed from p-type to n-type conduction. The x-ray diffraction (XRD) shows that our samples were pure Cu2O with a preferential orientation along the (111) direction. The intensity of (111) peak increases with the increase of Cl- concentration. The optical characterization of Cu2O was studied by analyzing the transmission spectrum measured in normal incidence in the range of 300-1100 nm. The thickness and the refractive index of Cu2O nanostructures were determined using different methods. The optical gap energy ( E g) and associated Urbach energy ( E u) were also calculated. Effectively, the optical gap was estimated from Tauc extrapolation; it was found that it decreases from 2.02 eV to 1.85 eV with the increase in CuCl2 concentration; on the other hand, the thickness of the layers increases from 267 nm to 300 nm.

Identification of a pathogenic FTO mutation by next-generation sequencing in a newborn with growth retardation and developmental delay.

PubMed

Daoud, Hussein; Zhang, Dong; McMurray, Fiona; Yu, Andrea; Luco, Stephanie M; Vanstone, Jason; Jarinova, Olga; Carson, Nancy; Wickens, James; Shishodia, Shifali; Choi, Hwanho; McDonough, Michael A; Schofield, Christopher J; Harper, Mary-Ellen; Dyment, David A; Armour, Christine M

2016-03-01

A homozygous loss-of-function mutation p.(Arg316Gln) in the fat mass and obesity-associated (FTO) gene, which encodes for an iron and 2-oxoglutarate-dependent oxygenase, was previously identified in a large family in which nine affected individuals present with a lethal syndrome characterised by growth retardation and multiple malformations. To date, no other pathogenic mutation in FTO has been identified as a cause of multiple congenital malformations. We investigated a 21-month-old girl who presented distinctive facial features, failure to thrive, global developmental delay, left ventricular cardiac hypertrophy, reduced vision and bilateral hearing loss. We performed targeted next-generation sequencing of 4813 clinically relevant genes in the patient and her parents. We identified a novel FTO homozygous missense mutation (c.956C>T; p.(Ser319Phe)) in the affected individual. This mutation affects a highly conserved residue located in the same functional domain as the previously characterised mutation p.(Arg316Gln). Biochemical studies reveal that p.(Ser319Phe) FTO has reduced 2-oxoglutarate turnover and N-methyl-nucleoside demethylase activity. Our findings are consistent with previous reports that homozygous mutations in FTO can lead to rare growth retardation and developmental delay syndrome, and further support the proposal that FTO plays an important role in early development of human central nervous and cardiovascular systems. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Does the FTO gene interact with the socioeconomic status on the obesity development among young European children? Results from the IDEFICS study.

PubMed

Foraita, R; Günther, F; Gwozdz, W; Reisch, L A; Russo, P; Lauria, F; Siani, A; Veidebaum, T; Tornaritis, M; Iacoviello, L; Vyncke, K; Pitsiladis, Y; Mårild, S; Molnár, D; Moreno, L A; Bammann, K; Pigeot, I

2015-01-01

Various twin studies revealed that the influence of genetic factors on psychological diseases or behaviour is more expressed in socioeconomically advantaged environments. Other studies predominantly show an inverse association between socioeconomic status (SES) and childhood obesity in Western developed countries. The aim of this study is to investigate whether the fat mass and obesity-associated (FTO) gene interacts with the SES on childhood obesity in a subsample (N = 4406) of the IDEFICS (Identification and prevention of Dietary- and lifestyle-induced health EFfects In Children and infantS) cohort. A structural equation model (SEM) is applied with the latent constructs obesity, dietary intakes, physical activity and fitness habits, and parental SES to estimate the main effects of the latter three variables and a FTO polymorphism on childhood obesity. Further, a multiple group SEM is used to explore whether an interaction effect exists between the single nucleotide polymorphism rs9939609 within the FTO gene and SES. Significant main effects are shown for physical activity and fitness (standardised [betacrc ](s) = -0.113), SES ([betacrc ](s) = -0.057) and the FTO homozygous AA risk genotype ([betacrc ](s) = -0.177). The explained variance of obesity is ~9%. According to the multiple group approach of SEM, we see an interaction between SES and FTO with respect to their effect on childhood obesity (Δχ(2) = 7.3, df = 2, P = 0.03). Children carrying the protective FTO genotype TT seem to be more protected by a favourable social environment regarding the development of obesity than children carrying the AT or AA genotype.

Metal oxide nanorod arrays on monolithic substrates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Pu-Xian; Guo, Yanbing; Ren, Zheng

A metal oxide nanorod array structure according to embodiments disclosed herein includes a monolithic substrate having a surface and multiple channels, an interface layer bonded to the surface of the substrate, and a metal oxide nanorod array coupled to the substrate surface via the interface layer. The metal oxide can include ceria, zinc oxide, tin oxide, alumina, zirconia, cobalt oxide, and gallium oxide. The substrate can include a glass substrate, a plastic substrate, a silicon substrate, a ceramic monolith, and a stainless steel monolith. The ceramic can include cordierite, alumina, tin oxide, and titania. The nanorod array structure can includemore » a perovskite shell, such as a lanthanum-based transition metal oxide, or a metal oxide shell, such as ceria, zinc oxide, tin oxide, alumina, zirconia, cobalt oxide, and gallium oxide, or a coating of metal particles, such as platinum, gold, palladium, rhodium, and ruthenium, over each metal oxide nanorod. Structures can be bonded to the surface of a substrate and resist erosion if exposed to high velocity flow rates.« less

The 'Fat Mass and Obesity Related' (FTO) gene: Mechanisms of Impact on Obesity and Energy Balance.

PubMed

Speakman, John R

2015-03-01

A cluster of single nucleotide polymorphisms (SNPs) in the first intron of the fat mass and obesity related (FTO) gene were the first common variants discovered to be associated with body mass index and body fatness. This review summarises what has been later discovered about the biology of FTO drawing together information from both human and animal studies. Subsequent work showed that the 'at risk' alleles of these SNPs are associated with greater food intake and increased hunger/lowered satiety, but are not associated with altered resting energy expenditure or low physical activity in humans. FTO is an FE (II) and 2-oxoglutarate dependent DNA/RNA methylase. Contrasting the impact of the SNPs on energy balance in humans, knocking out or reducing activity of the Fto gene in the mouse resulted in lowered adiposity, elevated energy expenditure with no impact on food intake (but the impact on expenditure is disputed). In contrast, overexpression of the gene in mice led to elevated food intake and adiposity, with no impact on expenditure. In rodents, the Fto gene is widely expressed in the brain including hypothalamic nuclei linked to food intake regulation. Since its activity is 2-oxoglutarate dependent it could potentially act as a sensor of citrate acid cycle flux, but this function has been dismissed, and instead it has been suggested to be much more likely to act as an amino acid sensor, linking circulating AAs to the mammalian target of rapamycin complex 1. This may be fundamental to its role in development but the link to obesity is less clear. It has been recently suggested that although the obesity related SNPs reside in the first intron of FTO, they may not only impact FTO but mediate their obesity effects via nearby genes (notably RPGRIP1L and IRX3).

Fat mass and obesity-associated gene rs11642015 polymorphism is significantly associated with prediabetes and type 2 diabetes subsequent to adjustment for body mass index.

PubMed

Han, Liyuan; Tang, Linlin; Wang, Changyi; Chen, Zhongwei; Zhang, Tao; Chen, Sihan; Liu, Shengyuan; Peng, Xiaolin; Mai, Yifeng; Duan, Shiwei

2014-09-01

The association of the fat mass and obesity-associated gene ( FTO ) rs11642015 polymorphism with prediabetes, type 2 diabetes and obesity in certain populations has not been previously reported. A population-based study was conducted that included 490 type 2 diabetic, 471 prediabetic and 575 normal subjects. The main outcomes of the study were prediabetes, type 2 diabetes and obesity. Binary logistic regression was performed to estimate the association of FTO rs11642015 with the risk of prediabetes, type 2 diabetes and obesity following adjustment for the corresponding confounders. A meta-analysis was also conducted to evaluate the association between FTO rs11642015 and obesity. FTO rs11642015 was significantly associated with prediabetes in the whole sample under the additive model [odds ratio (OR), 1.50; 95% confidence interval (CI), 1.17-1.93; P=0.002], particularly in females. The polymorphism remained consistently significant following adjustment for age and body mass index (BMI), showing an increased prediabetes risk with an additive effect (OR, 1.55; 95% CI, 1.19-2.01; P=0.001). In addition, a significant association was found for rs11642015 with prediabetes and type 2 diabetes under the dominant model. However, under the stringent Bonferroni's correction there was no evidence of positive associations for FTO rs11642015 with obesity in the whole sample, females or males. Findings of the meta-analysis showed that FTO rs11642015 was not predisposed to obesity. In conclusion, the T allele of FTO rs11642015 is positively associated with an increased risk of prediabetes, even after adjustment for age and BMI, particularly in females. Subjects carrying the CT + TT genotype are predisposed to prediabetes and type 2 diabetes. Therefore, results of the population-based study and follow-up meta-analysis suggested that FTO rs11642015 is not significantly associated with susceptibility to obesity.

No association between FTO or HHEX andendometrial cancer risk

PubMed Central

Gaudet, Mia M.; Yang, Hannah P.; Bosquet, Jesus Gonzalez; Healey, Catherine S.; Ahmed, Shahana; Dunning, Alison M.; Easton, Doug F.; Spurdle, Amanda B.; Ferguson, Kaltin; O’Mara, Tracy; Group, ANECS; Lambrechts, Diether; Despierre, Evelyn; Vergote, Ignace; Amant, Frederic; Lacey, James V.; Lissowska, Jola; Peplonska, Beata; Brinton, Louise A.; Chanock, Stephen; Garcia-Closas, Montserrat

2010-01-01

Introduction Obesity and diabetes are known risk factors for endometrial cancer; thus genetic risk factors of these phenotypes may also be associated with endometrial cancer risk. To evaluate this hypothesis, we genotyped tagSNPs and candidate SNPs in FTO and HHEX in a primary set of 417 endometrial cancer cases and 406 population-based controls, and validated significant findings in a replication set of approximately 2,347 cases and 3,140 controls from three additional studies. Methods We genotyped 189 tagSNPs in FTO (including rs8050136) and five tagSNPs in HHEX (including rs1111875) in the primary set and one SNP in each of FTO (rs12927155) and HHEX (rs1111875) in the validation set. Per allele odds ratios (OR) and 95% confidence intervals (CI) were calculated to estimate the association between the genotypes of each SNPs(as an ordinal variable)and endometrial cancer risk using unconditional logistic regression models, controlling for age and site. Results In the primary study, the most significant findings in FTO was rs12927155 (OR=1.56, 95% CI 1.21–2.01, p=5.8×10−4) and HHEX was rs1111875 (OR=0.80, 95% CI 0.66–0.97; p=0.026). In the validation studies, the pooled per allele ORs, adjusted for age and study, were for FTO rs12927155: OR=0.94, 95% CI 0.83–1.06, p=0.29 and for HHEX rs1111875: OR=1.00, 95%CI 0.92–1.10, p=0.96. Conclusion Our data indicate that common genetic variants in two genes previously related to obesity (FTO) and diabetes (HHEX) by genome-wide association scans are not associatedwith endometrial cancer risk. Impact Polymorphisms in FTO and HHEX are unlikely to have large effects on endometrial cancer risk but may have weaker effects. PMID:20647405

Nanostructured hematite for photoelectrochemical water splitting

NASA Astrophysics Data System (ADS)

Ling, Yichuan

Solar water splitting is an environmentally friendly reaction of producing hydrogen gas. Since Honda and Fujishima first demonstrated solar water splitting in 1972 by using semiconductor titanium dioxide (TiO2) as photoanode in a photoelectrochemical (PEC) cell, extensive efforts have been invested into improving the solar-to-hydrogen (STH) conversion efficiency and lower the production cost of photoelectrochemical devices. In the last few years, hematite (alpha-Fe2O3) nanostructures have been extensively studied as photoanodes for PEC water splitting. Although nanostructured hematite can improve its photoelectrochemical water splitting performance to some extent, by increasing active sites for water oxidation and shortening photogenerated hole path length to semiconductor/electrolyte interface, the photoactivity of pristine hematite nanostructures is still limited by a number of factors, such as poor electrical conductivities and slow oxygen evolution reaction kinetics. Previous studies have shown that tin (Sn) as an n-type dopant can substantially enhance the photoactivity of hematite photoanodes by modifying their optical and electrical properties. In this thesis, I will first demonstrate an unintentional Sn-doping method via high temperature annealing of hematite nanowires grown on fluorine-doped tin oxide (FTO) substrate to enhance the donor density. In addition to introducing extrinsic dopants into semiconductors, the carrier densities of hematite can also be enhanced by creating intrinsic defects. Oxygen vacancies function as shallow donors for a number of hematite. In this regard, I have investigated the influence of oxygen content on thermal decomposition of FeOOH to induce oxygen vacancies in hematite. In the end, I have studied low temperature activation of hematite nanostructures.

Visible light-induced water oxidation on mesoscopic alpha-Fe2O3 films made by ultrasonic spray pyrolysis.

PubMed

Duret, Alexis; Grätzel, Michael

2005-09-15

Alpha-Fe(2)O(3) films having a mesoscopic leaflet type structure were produced for the first time by ultrasonic spray pyrolysis (USP) to explore their potential as oxygen-evolving photoanodes. The target of these studies is to use translucent hematite films deposited on conducting fluorine doped tin oxide (FTO) glass as top electrodes in a tandem cell that accomplishes the cleavage of water into hydrogen and oxygen by sunlight. The properties of layers made by USP were compared to those deposited by conventional spray pyrolysis (SP). Although both types of films show similar XRD and UV-visible and Raman spectra, they differ greatly in their morphology. The mesoscopic alpha-Fe(2)O(3) layers produced by USP consist mainly of 100 nm-sized platelets with a thickness of 5-10 nm. These nanosheets are oriented mainly perpendicularly to the FTO support, their flat surface exposing (001) facets. The mesoscopic leaflet structure has the advantage that it allows for efficient harvesting of visible light, while offering at the same time the very short distance required for the photogenerated holes to reach the electrolyte interface before recombining with conduction band electrons. This allows for water oxidation by the valence band holes even though their diffusion length is only a few nanometers. Distances are longer in the particles produced by SP favoring recombination of photoinduced charge carriers. Open-circuit photovoltage measurements indicate a lower surface state density for the nanoplatelets as compared to the round particles. These factors explain the much higher photoactivity of the USP compared to the SP deposited alpha-Fe(2)O(3) layers. Addition of hydrogen peroxide to the alkaline electrolyte further improves the photocurrent-voltage characteristics of films generated by USP indicating the hole transfer from the valence band of the semiconductor oxide to the adsorbed water to be the rate-limiting kinetic step in the oxygen generation reaction.

Fundamental Study on the Fabrication of Inverted Planar Perovskite Solar Cells Using Two-Step Sequential Substrate Vibration-Assisted Spray Coating (2S-SVASC).

PubMed

Zabihi, Fatemeh; Ahmadian-Yazdi, Mohammad-Reza; Eslamian, Morteza

2016-12-01

In this paper, a scalable and fast process is developed and employed for the fabrication of the perovskite light harvesting layer in inverted planar heterojunction solar cell (FTO/PEDOT:PSS/CH3NH3PbI3-x Cl x /PCBM/Al). Perovskite precursor solutions are sprayed onto an ultrasonically vibrating substrate in two sequential steps via a process herein termed as the two-step sequential substrate vibration-assisted spray coating (2S-SVASC). The gentle imposed ultrasonic vibration on the substrate promotes droplet spreading and coalescence, surface wetting, evaporation, mixing of reagents, and uniform growth of perovskite nanocrystals. The role of the substrate temperature, substrate vibration intensity, and the time interval between the two sequential sprays are studied on the roughness, coverage, and crystalline structure of perovskite thin films. We demonstrate that a combination of a long time interval between spraying of precursor solutions (15 min), a high substrate temperature (120 °C), and a mild substrate vibration power (5 W) results in a favorable morphology and surface quality. The characteristics and performance of prepared perovskite thin films made via the 2S-SVASC technique are compared with those of the co-sprayed perovskite thin films. The maximum power conversion efficiency of 5.08 % on a 0.3-cm(2) active area is obtained for the device made via the scalable 2S-SVASC technique.

Electrical and structural characterization of plasma polymerized polyaniline/TiO2 heterostructure diode: a comparative study of single and bilayer TiO2 thin film electrode.

PubMed

Ameen, Sadia; Akhtar, M Shaheer; Kimi, Young Soon; Yang, O-Bong; Shin, Hyung-Shik

2011-04-01

A heterostructure was fabricated using p-type plasma polymerized polyaniline (PANI) and n-type (single and bilayer) titanium dioxide (TiO2) thin film on FTO glass. The deposition of single and bilayer TiO2 thin film on FTO substrate was achieved through doctor blade followed by dip coating technique before subjected to plasma enhanced polymerization. To fabricate p-n heterostructure, a plasma polymerization of aniline was conducted using RF plasma at 13.5 MHz and at the power of 120 W on the single and bilayer TiO2 thin film electrodes. The morphological, optical and the structural characterizations revealed the formation of p-n heterostructures between PANI and TiO2 thin film. The PANI/bilayer TiO2 heterostructure showed the improved current-voltage (I-V) characteristics due to the substantial deposition of PANI molecules into the bilayer TiO2 thin film which provided good conducting pathway and reduced the degree of excitons recombination. The change of linear I-V behavior of PANI/TiO2 heterostructure to non linear behavior with top Pt contact layer confirmed the formation of Schottky contact at the interfaces of Pt layer and PANI/TiO2 thin film layers.

Interaction between the FTO gene, body mass index and depression: meta-analysis of 13701 individuals†

PubMed Central

Rivera, Margarita; Locke, Adam E.; Corre, Tanguy; Czamara, Darina; Wolf, Christiane; Ching-Lopez, Ana; Milaneschi, Yuri; Kloiber, Stefan; Cohen-Woods, Sara; Rucker, James; Aitchison, Katherine J.; Bergmann, Sven; Boomsma, Dorret I.; Craddock, Nick; Gill, Michael; Holsboer, Florian; Hottenga, Jouke-Jan; Korszun, Ania; Kutalik, Zoltan; Lucae, Susanne; Maier, Wolfgang; Mors, Ole; Müller-Myhsok, Bertram; Owen, Michael J.; Penninx, Brenda W. J. H.; Preisig, Martin; Rice, John; Rietschel, Marcella; Tozzi, Federica; Uher, Rudolf; Vollenweider, Peter; Waeber, Gerard; Willemsen, Gonneke; Craig, Ian W.; Farmer, Anne E.; Lewis, Cathryn M.; Breen, Gerome; McGuffin, Peter

2017-01-01

Background Depression and obesity are highly prevalent, and major impacts on public health frequently co-occur. Recently, we reported that having depression moderates the effect of the FTO gene, suggesting its implication in the association between depression and obesity. Aims To confirm these findings by investigating the FTO polymorphism rs9939609 in new cohorts, and subsequently in a meta-analysis. Method The sample consists of 6902 individuals with depression and 6799 controls from three replication cohorts and two original discovery cohorts. Linear regression models were performed to test for association between rs9939609 and body mass index (BMI), and for the interaction between rs9939609 and depression status for an effect on BMI. Fixed and random effects meta-analyses were performed using METASOFT. Results In the replication cohorts, we observed a significant interaction between FTO, BMI and depression with fixed effects meta-analysis (β = 0.12, P = 2.7 × 10−4) and with the Han/Eskin random effects method (P = 1.4 × 10−7) but not with traditional random effects (β = 0.1, P = 0.35). When combined with the discovery cohorts, random effects meta-analysis also supports the interaction (β = 0.12, P = 0.027) being highly significant based on the Han/Eskin model (P = 6.9 × 10−8). On average, carriers of the risk allele who have depression have a 2.2% higher BMI for each risk allele, over and above the main effect of FTO. Conclusions This meta-analysis provides additional support for a significant interaction between FTO, depression and BMI, indicating that depression increases the effect of FTO on BMI. The findings provide a useful starting point in understanding the biological mechanism involved in the association between obesity and depression. PMID:28642257

A single FTO gene variant rs9939609 is associated with body weight evolution in a multiethnic extremely obese population that underwent bariatric surgery.

PubMed

Rodrigues, Gisele K; Resende, Cristina M M; Durso, Danielle F; Rodrigues, Lorena A A; Silva, José Luiz P; Reis, Rodrigo C; Pereira, Solange S; Ferreira, Daniela C; Franco, Gloria R; Alvarez-Leite, Jacqueline

2015-01-01

The rs9939609 single nucleotide polymorphism (SNP) in the fat mass and obesity-associated (FTO) gene is involved in obesity. Few studies have been conducted on patients who underwent bariatric surgery. The aim of this study was to evaluate the influence of FTO SNPs on body weight, body composition, and weight regain during a 60-mo follow-up period after bariatric surgery. The rs9939609 was genotyped in 146 individuals using a real-time polymerase chain reaction TaqMan assay. Data for lifestyle, comorbidities, body weight, body mass index (BMI), excess weight loss (EWL), and body composition were obtained before and 6, 12, 18, 24, 36, 48, and 60 mo after surgery. Data were analyzed by comparing two groups of patients according to rs9939609 FTO gene polymorphism. Mixed-regression models were constructed to evaluate the dynamics of body weight, BMI, and EWL over time in female patients. No differences were observed between the groups during the first 24 mo after surgery. After 36, 48, and 60 mo, body weight, fat mass, and BMI were higher, whereas fat-free mass and EWL were lower in the FTO-SNP patient group. Weight regain was more frequent and occurred sooner in the FTO-SNP group. There is a different evolution of weight loss in obese carriers of the FTO gene variant rs9939609 after bariatric surgery. However, this pattern was evident at only 2 y postbariatric surgery, inducing a lower proportion of surgery success and a greater and earlier weight regain. Copyright © 2015 Elsevier Inc. All rights reserved.

Visible light assisted photoelectrocatalytic degradation of sugarcane factory wastewater by sprayed CZTS thin films

NASA Astrophysics Data System (ADS)

Hunge, Y. M.; Mahadik, M. A.; Patil, V. L.; Pawar, A. R.; Gadakh, S. R.; Moholkar, A. V.; Patil, P. S.; Bhosale, C. H.

2017-12-01

Highly crystalline Cu2ZnSnS4 (CZTS) thin films have been deposited onto glass and FTO coated glass substrates by simple chemical spray-pyrolysis technique. It is an important material for solar energy conversion through the both photovoltaics and photocatalysis. The effect of substrate temperatures on the physico-chemical properties of the CZTS films is studied. The XRD study shows the formation of single phase CZTS with kesterite structure. FE-SEM analysis reveals nano flakes architecture with pin-hole and crake free surface with more adherent. The film deposited at optimized substrate temperature exhibits optical band gap energy of 1.90 eV, which lies in the visible region of the solar spectrum and useful for photocatalysis application. The photoelectrocatalytic activities of the large surface area (10 × 10 cm2) deposited CZTS thin film photocatalysts were evaluated for the degradation of sugarcane factory wastewater under visible light irradiation. The results show that the CZTS thin film photocatalyst exhibited about 90% degradation of sugar cane factory wastewater. The mineralization of sugarcane factory wastewater is studied by measuring chemical oxygen demand (COD) values.

[Association of polymorphic variants of FTO and MC4R genes with obesity in a Tatar population].

PubMed

Kochetova, O V; Korytina, G F; Akhmadishina, L Z; Semenov, E E; Viktorova, T V

2015-02-01

Obesity is a chronic relapsing disease that leads to numerous ailments and requires lifelong treatment. Genetic predisposition is one of the mostly discussed aspects of obesity development, and genome-wide association studies have provided evidence that several variants of the FTO and MC4R genes are significantly associated with obesity. In this study the association of FTO (rs9939609, rs7202116, and rs9930506) and MC4R (rs12970134 and rs17782313) genes' SNPs with obesity in Tatar women has been analyzed. In the investigation 340 women with obesity (Body Mass Index (BMI) ≥ 30 kg/m2) and 330 women from a control group (BMI up to 24.9 kg/m2) took part. The FTO rs9939609 (p = 0.0002) and rs9930506 (p = 0.0005) SNPs were shown to be associated with obesity risk following an additive model, while the MC4R rs12970134 (p = 0.0076) and rs1778231 (p = 0.021) SNPs were associated by a recessive model. We also showed an association of quantitative parameters (age, weight, and BMI) with two the FTO rs9939609 and rs9930506 SNPs and the association of age and the MC4R rs12970134 SNP. Our study demonstrates the role of genetic variability in FTO and MC4R genes in obesity development in Tatar women from Russia.

Influence of Nb-doped TiO2 blocking layers as a cascading band structure for enhanced photovoltaic properties

NASA Astrophysics Data System (ADS)

Koo, Bon-Ryul; Oh, Dong-Hyeun; Ahn, Hyo-Jin

2018-03-01

Nb-doped TiO2 (Nb-TiO2) blocking layers (BLs) were developed using horizontal ultrasonic spray pyrolysis deposition (HUSPD). In order to improve the photovoltaic properties of the dye-sensitized solar cells (DSSCs), we optimized the Nb doping level of the Nb-TiO2 BLs by controlling the Nb/Ti molar ratio (0, 5, 6, and 7) of the precursor solution for HUSPD. Compared to bare TiO2 BLs, the Nb-TiO2 BLs formed a cascading band structure using the positive shift of the conduction band minimum of the Nb-TiO2 positioned between fluorine-doped tin oxide (FTO) and TiO2. This results in the increase of the potential current and the suppression of the electron recombination. Hence, it led to the improvement of the electrical conductivity, due to the increased electron concentration by the Nb doping into TiO2. Therefore, the DSSC fabricated with the Nb-TiO2 BLs at a Nb/Ti molar ratio of 6 showed superior photoconversion efficiency (∼7.50 ± 0.20%) as a result of the improved short-circuit current density. This is higher than those with the other Nb-TiO2 BLs and without BL. This improvement of the photovoltaic properties for the DSSCs can be attributed to the synergistic effects of uniform and compact BL relative to the prevention of the backward electron transport at the FTO/electrolyte interface, efficient electron transport at interfaces relative to a cascading band structure of FTO/Nb-TiO2/TiO2 multilayers and the facilitated electron transport at the BLs relative to the increased electrical conductivity of the optimized Nb-TiO2 BLs.

Two candidate genes (FTO and INSIG2) for fat accumulation in four canids: chromosome mapping, gene polymorphisms and association studies of body and skin weight of red foxes.

PubMed

Grzes, M; Szczerbal, I; Fijak-Nowak, H; Szydlowski, M; Switonski, M

2011-01-01

Fat accumulation is a polygenic trait which has a significant impact on human health and animal production. Obesity is also an increasingly serious problem in dog breeding. The FTO and INSIG2 are considered as candidate genes associated with predisposition for human obesity. In this report we present a comparative genomic analysis of these 2 genes in 4 species belonging to the family Canidae - the dog and 3 species which are kept in captivity for fur production, i.e. red fox, arctic fox and Chinese raccoon dog. We cytogenetically mapped these 2 loci by FISH and compared the entire coding sequence of INSIG2 and a fragment of the coding sequence of FTO. The FTO gene was assigned to the following chromosomes: CFA2q25 (dog), VVU2q21 (red fox), ALA8q25 (arctic fox) and NPP10q24-25 (Chinese raccoon dog), while the INSIG2 was mapped to CFA19q17, VVU5p14, ALA24q15 and NPP9q22, respectively. Altogether, 29 SNPs were identified (16 in INSIG2 and 13 in FTO) and among them 2 were missense substitutions in the dog (23C/T, Thr>Met in the FTO gene and 40C/A, Arg>Ser in INSIG2). The distribution of these 2 SNPs was studied in 14 dog breeds. Two synonymous SNPs, one in the FTO gene (-28T>C in the 5'-flanking region) and one in the INSIG2 (10175C>T in intron 2), were used for the association studies in red foxes (n = 390) and suggestive evidence was observed for their association with body weight (FTO, p < 0.08) and weight of raw skin (INSIG2, p < 0.05). These associations indicate that both genes are potential candidates for growth or adipose tissue accumulation in canids. We also suggest that the 2 missense substitutions found in dogs should be studied in terms of genetic predisposition to obesity. Copyright © 2011 S. Karger AG, Basel.

An FTO variant is associated with Type 2 diabetes in South Asian populations after accounting for body mass index and waist circumference

PubMed Central

Rees, S. D.; Islam, M.; Hydrie, M. Z. I.; Chaudhary, B.; Bellary, S.; Hashmi, S.; O’Hare, J. P.; Kumar, S.; Sanghera, D. K.; Chaturvedi, N.; Barnett, A. H.; Shera, A. S.; Weedon, M. N.; Basit, A.; Frayling, T. M.; Kelly, M. A.; Jafar, T. H.

2011-01-01

Aims A common variant, rs9939609, in the FTO (fat mass and obesity) gene is associated with adiposity in Europeans, explaining its relationship with diabetes. However, data are inconsistent in South Asians. Our aim was to investigate the association of the FTO rs9939609 variant with obesity, obesity-related traits and Type 2 diabetes in South Asian individuals, and to use meta-analyses to attempt to clarify to what extent BMI influences the association of FTO variants with diabetes in South Asians. Methods We analysed rs9939609 in two studies of Pakistani individuals: 1666 adults aged ≥ 40 years from the Karachi population-based Control of Blood Pressure and Risk Attenuation (COBRA) study and 2745 individuals of Punjabi ancestry who were part of a Type 2 diabetes case–control study (UK Asian Diabetes Study/Diabetes Genetics in Pakistan; UKADS/DGP). The main outcomes were BMI, waist circumference and diabetes. Regression analyses were performed to determine associations between FTO alleles and outcomes. Summary estimates were combined in a meta-analysis of 8091 South Asian individuals (3919 patients with Type 2 diabetes and 4172 control subjects), including those from two previous studies. Results In the 4411 Pakistani individuals from this study, the age-, sex- and diabetes-adjusted association of FTO variant rs9939609 with BMI was 0.45 (95% CI 0.24–0.67) kg/m2 per A-allele (P = 3.0× 10−5) and with waist circumference was 0.88 (95% CI 0.36–1.41) cm per A-allele (P = 0.001). The A-allele (30% frequency) was also significantly associated with Type 2 diabetes [per A-allele odds ratio (95% CI) 1.18 (1.07–1.30); P = 0.0009]. A meta-analysis of four South Asian studies with 8091 subjects showed that the FTO A-allele predisposes to Type 2 diabetes [1.22 (95% CI 1.14–1.31); P = 1.07× 10−8] even after adjusting for BMI [1.18 (95% CI 1.10–1.27); P = 1.02× 10−5] or waist circumference [1.18 (95% CI 1.10–1.27); P = 3.97× 10−5]. Conclusions The strong association between FTO genotype and BMI and waist circumference in South Asians is similar to that observed in Europeans. In contrast, the strong association of FTO genotype with diabetes is only partly accounted for by BMI. PMID:21294771

Electroforming free controlled bipolar resistive switching in Al/CoFe2O4/FTO device with self-compliance effect

NASA Astrophysics Data System (ADS)

Munjal, Sandeep; Khare, Neeraj

2018-02-01

Controlled bipolar resistive switching (BRS) has been observed in nanostructured CoFe2O4 (CFO) films using an Al (aluminum)/CoFe2O4/FTO (fluorine-doped tin oxide) device. The fabricated device shows electroforming-free uniform BRS with two clearly distinguished and stable resistance states without any application of compliance current, with a resistance ratio of the high resistance state (HRS) and the low resistance state (LRS) of >102. Small switching voltage (<1 volt) and lower current in both the resistance states confirm the fabrication of a low power consumption device. In the LRS, the conduction mechanism was found to be Ohmic in nature, while the high-resistance state (HRS/OFF state) was governed by the space charge-limited conduction mechanism, which indicates the presence of an interfacial layer with an imperfect microstructure near the top Al/CFO interface. The device shows nonvolatile behavior with good endurance properties, an acceptable resistance ratio, uniform resistive switching due to stable, less random filament formation/rupture, and a control over the resistive switching properties by choosing different stop voltages, which makes the device suitable for its application in future nonvolatile resistive random access memory.

Ready to use bioinformatics analysis as a tool to predict immobilisation strategies for protein direct electron transfer (DET).

PubMed

Cazelles, R; Lalaoui, N; Hartmann, T; Leimkühler, S; Wollenberger, U; Antonietti, M; Cosnier, S

2016-11-15

Direct electron transfer (DET) to proteins is of considerable interest for the development of biosensors and bioelectrocatalysts. While protein structure is mainly used as a method of attaching the protein to the electrode surface, we employed bioinformatics analysis to predict the suitable orientation of the enzymes to promote DET. Structure similarity and secondary structure prediction were combined underlying localized amino-acids able to direct one of the enzyme's electron relays toward the electrode surface by creating a suitable bioelectrocatalytic nanostructure. The electro-polymerization of pyrene pyrrole onto a fluorine-doped tin oxide (FTO) electrode allowed the targeted orientation of the formate dehydrogenase enzyme from Rhodobacter capsulatus (RcFDH) by means of hydrophobic interactions. Its electron relays were directed to the FTO surface, thus promoting DET. The reduction of nicotinamide adenine dinucleotide (NAD(+)) generating a maximum current density of 1μAcm(-2) with 10mM NAD(+) leads to a turnover number of 0.09electron/s/molRcFDH. This work represents a practical approach to evaluate electrode surface modification strategies in order to create valuable bioelectrocatalysts. Copyright © 2016 Elsevier B.V. All rights reserved.

A High Intake of Saturated Fatty Acids Strengthens the Association between the Fat Mass and Obesity-Associated Gene and BMI123

PubMed Central

Corella, Dolores; Arnett, Donna K.; Tucker, Katherine L.; Kabagambe, Edmond K.; Tsai, Michael; Parnell, Laurence D.; Lai, Chao-Qiang; Lee, Yu-Chi; Warodomwichit, Daruneewan; Hopkins, Paul N.; Ordovas, Jose M.

2011-01-01

Evidence that physical activity (PA) modulates the association between the fat mass and obesity-associated gene (FTO) and BMI is emerging; however, information about dietary factors modulating this association is scarce. We investigated whether fat and carbohydrate intake modified the association of FTO gene variation with BMI in two populations, including participants in the Genetics of Lipid Lowering Drugs and Diet Network (GOLDN) study (n = 1069) and in the Boston Puerto Rican Health (BPRHS) study (n = 1094). We assessed energy, nutrient intake, and PA using validated questionnaires. Genetic variability at the FTO locus was characterized by polymorphisms rs9939609 (in the GOLDN) and rs1121980 (in the GOLDN and BPRHS). We found significant interactions between PA and FTO on BMI in the GOLDN but not in the BPRHS. We found a significant interaction between SFA intake and FTO on BMI, which was stronger than that of total fat and was present in both populations (P-interaction = 0.007 in the GOLDN and P-interaction = 0.014 in BPRHS for categorical; and P-interaction = 0.028 in the GOLDN and P-interaction = 0.041 in BPRHS for continuous SFA). Thus, homozygous participants for the FTO-risk allele had a higher mean BMI than the other genotypes only when they had a high-SFA intake (above the population mean: 29.7 ± 0.7 vs. 28.1 ± 0.5 kg/m2; P = 0.037 in the GOLDN and 33.6. ± 0.8 vs. 31.2 ± 0.4 kg/m2; P = 0.006 in BPRHS). No associations with BMI were found at lower SFA intakes. We found no significant interactions with carbohydrate intake. In conclusion, SFA intake modulates the association between FTO and BMI in American populations. PMID:22049296

Interaction between obesity-related genes, FTO and MC4R, associated to an increase of breast cancer risk.

PubMed

da Cunha, Patrícia Amorim; de Carlos Back, Lia Kubelka; Sereia, Aline Fernanda Rodrigues; Kubelka, Clara; Ribeiro, Maria Cecíia Menks; Fernandes, Bráulio Leal; de Souza, Ilíada Rainha

2013-12-01

Breast cancer (BC) is a complex disease and obesity is a well-known risk factor for its development, especially after menopause. Several studies have shown Single Nucleotide Polymorphisms (SNPs) linked to overweight and obesity, such as: rs1121980 (T/C) and rs9939609 (A/T) in Fat Mass and Obesity Associated gene (FTO) and rs17782313 (T/C) in Melanocortin 4 Receptor gene (MC4R). Thus, we aimed to investigate the association between these obesity-related SNPs and BC risk. One hundred BC patients and 148 healthy women from Santa Catarina, Brazil entered the study. SNPs were genotyped using Taqman assays. For statistical analyses SNPStats and SPSS softwares were used. Association analyses were performed by logistic regression and were adjusted for age and Body mass index (BMI). Multiple SNPs inheritance models (log-additive, dominant, recessive, codominant) were performed to determine odds ratios (ORs), assuming 95 % confidence interval (CI) and P value = 0.05 as the significance limit. When analyzed alone, FTO rs1121980 and rs9939609 did not show significant associations with BC development, however MC4R rs17782313 showed increased risk for BC even after adjustments (P-value = 0.032). Interestingly, the interaction of FTO and MC4R polymorphisms showed a powerful association with BC. We observed a 4.59-fold increased risk for woman who have the allele combination C/T/C (FTO rs1121980/FTO rs9939609/MC4R rs17782313) (P-value = 0.0011, adjusted for age and BMI). We found important and unpublished associations between these obesity-related genes and BC risk. These associations seem to be independent of their effect on BMI, indicating a direct role of the interaction between FTO and MC4R polymorphisms in BC development.

Effects of TiO2 electron blocking layer on photovoltaic performance of photo-electrochemical cell

NASA Astrophysics Data System (ADS)

Bin, Jae-Wook; Kim, Doo-Hwan; Sung, Youl-Moon; Park, Min-Woo

2014-06-01

Dye-sensitized solar cells (DSCs) have used transparent conductive Fluorine-doped SnO2 (FTO) glass/porous TiO2 layer attached using dye molecules/electrolytes (I-/I3-)/Platinium-coated FTO glass configuration. In this work, prior to the coating of nanoporous TiO2 layer on FTO glass, a dense layer of TiO2 film with a thickness of less than ∼100 nm was deposited directly onto the FTO as an electron blocking layer by radio frequency (RF) magnetron sputtering. Under 100 mW/cm2 illumination at AM 1.5, the energy conversion efficiency (η) of the prepared DSC with electron blocking layer of 80 nm thickness was 6.9% (Voc = 0.67 V, Jsc = 12.18 mA/cm2, ff = 0.63), which is increased by 1.3% compared to the typical cell without electron blocking layer.

100-Fold Enhancement of Charge Transport in Uniaxially Oriented Mesoporous Anatase TiO 2 Films

DOE PAGES

Li, Ke; Liu, Jie; Sheng, Xia; ...

2017-12-04

Mesoporous semiconductor films are of considerable interest for applications in photoelectrochemical devices, however, despite intensive research till now, their charge transport properties remain significantly lower than their single-crystal counterparts. Herein, we report a novel low-temperature template-free technique for growing high surface area mesoporous anatase TiO2 films with a preferred [001] crystalline-orientation on FTO-coated glass substrate. Compared to mesoporous films that comprised of randomly oriented crystallites, the uniaxial orientation enables a 100-fold increase in the rate of electron transport. The uniaxially oriented mesoporous anatase TiO2 films exhibit should greatly facilitate the development and application of photoelectrochemical and electrochemical devices.

Physics and applications of electrochromic devices

NASA Astrophysics Data System (ADS)

Pawlicka, Agnieszka; Avellaneda, Cesar O.

2003-07-01

Solid state electrochromic devices (ECD) are of considerable technological and commercial interest because of their controllable transmission, absorption and/or reflectance. For instance, a major application of these devices is in smart windows that can regulate the solar gains of buildings and also in glare attenuation in automobile rear view mirrors. Other applications include solar cells, small and large area flat panel displays, satellite temperature control, food monitoring, and document authentication. A typical electrochromic device has a five-layer structure: GS/TC/EC/IC/IS/TC/GS, where GS is a glass substrate, TC is a transparent conductor, generally ITO (indium tin oxide) or FTO (fluorine tin oxide), EC is an electrochromic coating, IC is an ion conductor (solid or liquid electrolyte) and IS is an ion storage coating. Generally, the EC and IS layers are deposited separately on the TC coatings and then jointed with the IC and sealed. The EC and IS are thin films that can be deposited by sputtering, CVD, sol-gel precursors, etc. There are different kinds of organic, inorganic and organic-inorganic films that can be used to make electrochromic devices. Thin electrochromic films can be: WO3, Nb2O5, Nb2O5:Li+ or Nb2O5-TiO2 coatings, ions storage films: CeO2-TiO2, CeO2-ZrO2 or CeO2-TiO2-ZrO2 and electrolytes like Organically Modified Electrolytes (Ormolytes) or polymeric films also based on natural polymers like starch or cellulose. These last are very interesting due to their high ionic conductivity, high transparency and good mechanical properties. This paper describes construction and properties of different thin oxide and polymeric films and also shows the optical response of an all sol-gel electrochromic device with WO3/Ormolyte/CeO2-TiO2 configuration.

Genetic variants of FTO influence adiposity, insulin sensitivity, leptin levels, and resting metabolic rate in the Quebec Family Study.

PubMed

Do, Ron; Bailey, Swneke D; Desbiens, Katia; Belisle, Alexandre; Montpetit, Alexandre; Bouchard, Claude; Pérusse, Louis; Vohl, Marie-Claude; Engert, James C

2008-04-01

A genome-wide association study conducted by the Wellcome Trust Case Control Consortium recently associated single nucleotide polymorphisms (SNPs) in the FTO (fatso/fat mass and obesity associated) gene with type 2 diabetes. These associations were shown to be mediated by obesity. Other research groups found similar results in Europeans and Hispanics but not African Americans. The mechanism by which FTO influences obesity and type 2 diabetes is currently unknown. The present study investigated the role of two FTO SNPs (rs17817449 and rs1421085) in adiposity, insulin sensitivity, and body weight regulation, including energy intake and expenditure. We genotyped 908 individuals from the Quebec City metropolitan area that participated in the Quebec Family Study, a long-term study of extensively phenotyped individuals designed to investigate factors involved in adiposity. We found significant associations for both SNPs with several obesity-related phenotypes. In particular, rs17817449 was associated with BMI (P = 0.0014), weight (P = 0.0059), and waist circumference (P = 0.0021) under an additive model. In addition, this FTO SNP influenced fasting insulin (P = 0.011), homeostasis model assessment of insulin resistance (P = 0.038), and an insulin sensitivity index derived from an oral glucose tolerance test (P = 0.0091). Associations were also found with resting metabolic rate (RMR) (P = 0.042) and plasma leptin levels (P = 0.036). Adjustment for BMI abolished the associations with insulin sensitivity, RMR, and plasma leptin levels. These results confirm that genetic variation at the FTO locus contributes to the etiology of obesity, insulin resistance, and increased plasma leptin levels.

Association of FTO rs9939609 SNP with Obesity and Obesity- Associated Phenotypes in a North Indian Population

PubMed Central

Prakash, Jai; Mittal, Balraj; Srivastava, Apurva; Awasthi, Shally; Srivastava, Neena

2016-01-01

Objectives Obesity is a common disorder that has a significant impact on morbidity and mortality. Twin and adoption studies support the genetic influence on variation of obesity, and the estimates of the heritability of body mass index (BMI) is significantly high (30 to 70%). Variants in the fat mass and obesity-associated (FTO) gene have been associated with obesity and obesity-related phenotypes in different populations. The aim of this study was to examine the association of FTO rs9939609 with obesity and related phenotypes in North Indian subjects.   Methods Gene variants were investigated for association with obesity in 309 obese and 333 non-obese patients. Genotyping of the FTO rs9939609 single nucleotide polymorphism (SNP) was analyzed using Restriction Fragment Length Polymorphism Analysis of PCR-Amplified Fragments. We also measured participants fasting glucose and insulin levels, lipid profile, percentage body fat, fat mass and fat free mass.   Results Waist to hip ratio, systolic blood pressure, diastolic blood pressure, percentage body fat, fat mass, insulin concentration, and homeostasis model assessment index (HOMA-Index) showed a significant difference between the study groups. Significant associations were found for FTO rs9939609 SNP with obesity and obesity-related phenotypes. The significant associations were observed between the rs9939609 SNP and blood pressure, fat mass, insulin, and HOMA-index under a different model.   Conclusion This study presents significant association between FTO rs9939609 and obesity defined by BMI and also established the strong association with several measures of obesity in North Indian population. PMID:27168919

FTO genotype, dietary protein, and change in appetite: the Preventing Overweight Using Novel Dietary Strategies trial.

PubMed

Huang, Tao; Qi, Qibin; Li, Yanping; Hu, Frank B; Bray, George A; Sacks, Frank M; Williamson, Donald A; Qi, Lu

2014-05-01

A common obesity-risk variant rs9939609 in the fat mass- and obesity-associated (FTO) gene was recently shown to affect appetite, and the gene is sensitive to the regulation of amino acids. We examined the interaction between FTO genotype and protein intake on the long-term changes in appetite in a randomized controlled trial. We genotyped FTO rs9939609 in 737 overweight adults in the 2-y Preventing Overweight Using Novel Dietary Strategies trial and assessed 4 appetite-related traits including cravings, fullness, hunger, and prospective consumption. We showed that dietary protein significantly modified genetic effects on changes in food cravings and appetite scores at 6 mo after adjustment for age, sex, ethnicity, baseline body mass index, weight change, and baseline value for respective outcomes (P-interaction = 0.027 and 0.048, respectively). The A allele was associated with a greater decrease in food cravings and appetite scores in participants with high-protein-diet intake (P = 0.027 and 0.047, respectively) but not in subjects in the low-protein-diet group (P = 0.384 and 0.078, respectively). The weight regain from 6 to 24 mo attenuated gene-protein interactions. Protein intakes did not modify FTO genotype effects on other appetite measures. Our data suggest that individuals with the FTO rs9939609 A allele might obtain more benefits in a reduction of food cravings and appetite by choosing a hypocaloric and higher-protein weight-loss diet. This trial was registered at clinicaltrials.gov as NCT00072995.

FTO genotype, dietary protein, and change in appetite: the Preventing Overweight Using Novel Dietary Strategies trial123

PubMed Central

Huang, Tao; Li, Yanping; Hu, Frank B; Bray, George A; Sacks, Frank M; Williamson, Donald A; Qi, Lu

2014-01-01

Background: A common obesity-risk variant rs9939609 in the fat mass– and obesity-associated (FTO) gene was recently shown to affect appetite, and the gene is sensitive to the regulation of amino acids. Objective: We examined the interaction between FTO genotype and protein intake on the long-term changes in appetite in a randomized controlled trial. Design: We genotyped FTO rs9939609 in 737 overweight adults in the 2-y Preventing Overweight Using Novel Dietary Strategies trial and assessed 4 appetite-related traits including cravings, fullness, hunger, and prospective consumption. Results: We showed that dietary protein significantly modified genetic effects on changes in food cravings and appetite scores at 6 mo after adjustment for age, sex, ethnicity, baseline body mass index, weight change, and baseline value for respective outcomes (P-interaction = 0.027 and 0.048, respectively). The A allele was associated with a greater decrease in food cravings and appetite scores in participants with high-protein–diet intake (P = 0.027 and 0.047, respectively) but not in subjects in the low-protein–diet group (P = 0.384 and 0.078, respectively). The weight regain from 6 to 24 mo attenuated gene-protein interactions. Protein intakes did not modify FTO genotype effects on other appetite measures. Conclusion: Our data suggest that individuals with the FTO rs9939609 A allele might obtain more benefits in a reduction of food cravings and appetite by choosing a hypocaloric and higher-protein weight-loss diet. This trial was registered at clinicaltrials.gov as NCT00072995. PMID:24622803

The FTO A/T Polymorphism and Elite Athletic Performance: A Study Involving Three Groups of European Athletes

PubMed Central

Eynon, Nir; Nasibulina, Emiliya S.; Banting, Lauren K.; Cieszczyk, Pawel; Maciejewska-Karlowska, Agnieszka; Sawczuk, Marek; Bondareva, Elvira A.; Shagimardanova, Roza R.; Raz, Maytal; Sharon, Yael; Williams, Alun G.; Ahmetov, Ildus I.

2013-01-01

Objective The FTO A/T polymorphism (rs9939609) is a strong candidate to influence obesity-related traits. Elite athletes from many different sporting disciplines are characterized by low body fat. Therefore, the aim of this study was to assess whether athletic status is associated with the FTO A/T polymorphism. Subjects and Methods A large cohort of European Caucasians from Poland, Russia and Spain were tested to examine the association between FTO A/T polymorphism (rs9939609) and athletic status. A total of 551 athletes were divided by type of sport (endurance athletes, n = 266 vs. sprint/power athletes, n = 285) as well as by level of competition (elite-level vs. national-level). The control group consisted of 1,416 ethnically-matched, non-athletic participants, all Europeans. Multinomial logistic regression analyses were conducted to assess the association between FTO A/T genotypes and athletic status/competition level. Results There were no significantly greater/lesser odds of harbouring any type of genotype when comparing across athletic status (endurance athletes, sprint/power athletes or control participants). These effects were observed after controlling for sex and nationality. Furthermore, no significantly greater/lesser odds ratios were observed for any of the genotypes in respect to the level of competition (elite-level vs. national-level). Conclusion The FTO A/T polymorphism is not associated with elite athletic status in the largest group of elite athletes studied to date. Large collaborations and data sharing between researchers, as presented here, are strongly recommended to enhance the research in the field of exercise genomics. PMID:23573268

Continuous lengths of oxide superconductors

DOEpatents

Kroeger, Donald M.; List, III, Frederick A.

2000-01-01

A layered oxide superconductor prepared by depositing a superconductor precursor powder on a continuous length of a first substrate ribbon. A continuous length of a second substrate ribbon is overlaid on the first substrate ribbon. Sufficient pressure is applied to form a bound layered superconductor precursor powder between the first substrate ribbon and the second substrate ribbon. The layered superconductor precursor is then heat treated to establish the oxide superconducting phase. The layered oxide superconductor has a smooth interface between the substrate and the oxide superconductor.

R-2HG Exhibits Anti-tumor Activity by Targeting FTO/m6A/MYC/CEBPA Signaling.

PubMed

Su, Rui; Dong, Lei; Li, Chenying; Nachtergaele, Sigrid; Wunderlich, Mark; Qing, Ying; Deng, Xiaolan; Wang, Yungui; Weng, Xiaocheng; Hu, Chao; Yu, Mengxia; Skibbe, Jennifer; Dai, Qing; Zou, Dongling; Wu, Tong; Yu, Kangkang; Weng, Hengyou; Huang, Huilin; Ferchen, Kyle; Qin, Xi; Zhang, Bin; Qi, Jun; Sasaki, Atsuo T; Plas, David R; Bradner, James E; Wei, Minjie; Marcucci, Guido; Jiang, Xi; Mulloy, James C; Jin, Jie; He, Chuan; Chen, Jianjun

2018-01-11

R-2-hydroxyglutarate (R-2HG), produced at high levels by mutant isocitrate dehydrogenase 1/2 (IDH1/2) enzymes, was reported as an oncometabolite. We show here that R-2HG also exerts a broad anti-leukemic activity in vitro and in vivo by inhibiting leukemia cell proliferation/viability and by promoting cell-cycle arrest and apoptosis. Mechanistically, R-2HG inhibits fat mass and obesity-associated protein (FTO) activity, thereby increasing global N 6 -methyladenosine (m 6 A) RNA modification in R-2HG-sensitive leukemia cells, which in turn decreases the stability of MYC/CEBPA transcripts, leading to the suppression of relevant pathways. Ectopically expressed mutant IDH1 and S-2HG recapitulate the effects of R-2HG. High levels of FTO sensitize leukemic cells to R-2HG, whereas hyperactivation of MYC signaling confers resistance that can be reversed by the inhibition of MYC signaling. R-2HG also displays anti-tumor activity in glioma. Collectively, while R-2HG accumulated in IDH1/2 mutant cancers contributes to cancer initiation, our work demonstrates anti-tumor effects of 2HG in inhibiting proliferation/survival of FTO-high cancer cells via targeting FTO/m 6 A/MYC/CEBPA signaling. Copyright © 2017 Elsevier Inc. All rights reserved.

Common variants in the obesity-associated genes FTO and MC4R are not associated with risk of colorectal cancer

PubMed Central

Yang, Baiyu; Thrift, Aaron P.; Figueiredo, Jane C.; Jenkins, Mark A.; Schumacher, Fredrick R.; Conti, David V.; Lin, Yi; Win, Aung Ko; Limburg, Paul J.; Berndt, Sonja I.; Brenner, Hermann; Chan, Andrew T.; Chang-Claude, Jenny; Hoffmeister, Michael; Hudson, Thomas J.; Marchand, Loïc Le; Newcomb, Polly A.; Slattery, Martha L.; White, Emily; Peters, Ulrike; Casey, Graham; Campbell, Peter T.

2016-01-01

Background Obesity is a convincing risk factor for colorectal cancer. Genetic variants in or near FTO and MC4R are consistently associated with body mass index and other body size measures, but whether they are also associated with colorectal cancer risk is unclear. Methods In the discovery stage, we tested associations of 677 FTO and 323 MC4R single nucleotide polymorphisms (SNPs) 100kb upstream and 300kb downstream from each respective locus with risk of colorectal cancer in data from the Colon Cancer Family Registry (CCFR: 1,960 cases; 1,777 controls). Next, all SNPs that were nominally statistically signif icant (p<0.05) in the discovery stage were included in replication analyses in data from the Genetics and Epidemiology of Colorectal Cancer Consortium (GECCO: 9,716 cases; 9,844 controls). Results In the discovery stage, 43 FTO variants and 18 MC4R variants were associated with colorectal cancer risk (p<0.05). No SNPs remained statistically significant in the replication analysis after accounting for multiple comparisons. Conclusion We found no evidence that individual variants in or near the obesity-related genes FTO and MC4R are associated with risk of colorectal cancer. PMID:27449576

Common variants in the obesity-associated genes FTO and MC4R are not associated with risk of colorectal cancer.

PubMed

Yang, Baiyu; Thrift, Aaron P; Figueiredo, Jane C; Jenkins, Mark A; Schumacher, Fredrick R; Conti, David V; Lin, Yi; Win, Aung Ko; Limburg, Paul J; Berndt, Sonja I; Brenner, Hermann; Chan, Andrew T; Chang-Claude, Jenny; Hoffmeister, Michael; Hudson, Thomas J; Marchand, Loïc Le; Newcomb, Polly A; Slattery, Martha L; White, Emily; Peters, Ulrike; Casey, Graham; Campbell, Peter T

2016-10-01

Obesity is a convincing risk factor for colorectal cancer. Genetic variants in or near FTO and MC4R are consistently associated with body mass index and other body size measures, but whether they are also associated with colorectal cancer risk is unclear. In the discovery stage, we tested associations of 677 FTO and 323 MC4R single nucleotide polymorphisms (SNPs) 100kb upstream and 300kb downstream from each respective locus with risk of colorectal cancer in data from the Colon Cancer Family Registry (CCFR: 1960 cases; 1777 controls). Next, all SNPs that were nominally statistically significant (p<0.05) in the discovery stage were included in replication analyses in data from the Genetics and Epidemiology of Colorectal Cancer Consortium (GECCO: 9716 cases; 9844 controls). In the discovery stage, 43 FTO variants and 18 MC4R variants were associated with colorectal cancer risk (p<0.05). No SNPs remained statistically significant in the replication analysis after accounting for multiple comparisons. We found no evidence that individual variants in or near the obesity-related genes FTO and MC4R are associated with risk of colorectal cancer. Copyright © 2016 Elsevier Ltd. All rights reserved.

Silica substrate or portion formed from oxidation of monocrystalline silicon

DOEpatents

Matzke, Carolyn M.; Rieger, Dennis J.; Ellis, Robert V.

2003-07-15

A method is disclosed for forming an inclusion-free silica substrate using a monocrystalline silicon substrate as the starting material and oxidizing the silicon substrate to convert it entirely to silica. The oxidation process is performed from both major surfaces of the silicon substrate using a conventional high-pressure oxidation system. The resulting product is an amorphous silica substrate which is expected to have superior etching characteristics for microfabrication than conventional fused silica substrates. The present invention can also be used to convert only a portion of a monocrystalline silicon substrate to silica by masking the silicon substrate and locally thinning a portion the silicon substrate prior to converting the silicon portion entirely to silica. In this case, the silica formed by oxidizing the thinned portion of the silicon substrate can be used, for example, as a window to provide optical access through the silicon substrate.

Physical activity modifies the FTO effect on BMI change in Japanese adolescents.

PubMed

Shinozaki, Keiko; Okuda, Masayuki; Okayama, Naoko; Kunitsugu, Ichiro

2018-04-14

Evidence of the effects of fat mass and obesity-associated (FTO) gene variation and long-term effects of physical activity (PA) on adiposity in adolescents is largely scarce. This study aimed to investigate whether physical activity modulates the effects of the FTO gene on body mass index (BMI) changes in Japanese adolescents between the ages of 13 and 18 years. Data of 343 subjects (156 boys; 187 girls) who were enrolled in 2006 and 2007 from schools on Shunan City, Japan, were collected. Genotyping (rs1558902) was conducted, and anthropometric measurements and blood test results were recorded for subjects in the eighth grade. A second survey involving self-reporting of anthropometric measurements was conducted when the subjects were in the twelfth grade. PA was estimated using the International Physical Activity Questionnaire in this survey. BMI and the standard deviation score for BMI (BMI-SDS) were calculated. BMI changes and BMI-SDS changes were compared among FTO genotypes using a multivariate model. The effect of the interaction between PA and the FTO genotype on BMI changes was significant among boys but not girls. Among boys, PA had a significant negative influence on BMI-SDS changes in those with the AA genotype and a significant positive influence on BMI and BMI-SDS changes in those with the TT genotype. These data suggest that the influence of PA on BMI changes and BMI-SDS changes varied on the basis of genotype. PA modified the effect of the FTO gene on BMI changes in Japanese boys. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Association of fatty acid-binding protein 2 and fat mass and obesity-associated gene polymorphism with primary open-angle glaucoma

PubMed Central

Abbas, Shania; Raza, Syed Tasleem; Chandra, Anu; Singh, Luxmi; Mahdi, Farzana

2017-01-01

PURPOSE: The present study was carried out to investigate the association of fatty acid-binding protein 2 (FABP2) and fat mass and obesity-associated (FTO) gene polymorphism with primary open-angle glaucoma (POAG) cases and controls. MATERIALS AND METHODS: This study includes 122 POAG cases and 112 controls. FABP2 and FTO gene polymorphisms in cases and controls were evaluated by polymerase chain reaction-restriction fragment length polymorphism method. RESULTS: The mean ages were 49.88 ± 12.34 and 53.74 ± 11.87 years in POAG cases and control groups, respectively. The FABP2 gene AA, AT, TT genotype frequencies were 12.90%, 62.40%, 24.80% in POAG cases and 20.60%, 64.70%, 14.70% in healthy controls, respectively. The frequencies of A and T allele in POAG cases were 44.06% and 55.94% as compared to 52.94% and 47.06% in the controls. The FTO gene AA, AT, TT genotype frequencies were 2.00%, 79.20%, 18.80% in cases and 0%, 75.50%, 24.50% in healthy controls, respectively. The frequencies of A and T allele in POAG cases were 41.58% and 58.42% as compared to 37.75% and 62.25% in the controls. No significant difference in the frequencies of FABP2 and FTO genotype was found between POAG cases and controls. CONCLUSION: We could not identify the possible association of FABP2 and FTO gene polymorphism with POAG; however, further studies with larger sample size in different population are require to clarify the role of FABP2 and FTO genes in susceptibility to POAG. PMID:29034152

Contributions of Function-Altering Variants in Genes Implicated in Pubertal Timing and Body Mass for Self-Limited Delayed Puberty.

PubMed

Howard, Sasha R; Guasti, Leonardo; Poliandri, Ariel; David, Alessia; Cabrera, Claudia P; Barnes, Michael R; Wehkalampi, Karoliina; O'Rahilly, Stephen; Aiken, Catherine E; Coll, Anthony P; Ma, Marcella; Rimmington, Debra; Yeo, Giles S H; Dunkel, Leo

2018-02-01

Self-limited delayed puberty (DP) is often associated with a delay in physical maturation, but although highly heritable the causal genetic factors remain elusive. Genome-wide association studies of the timing of puberty have identified multiple loci for age at menarche in females and voice break in males, particularly in pathways controlling energy balance. We sought to assess the contribution of rare variants in such genes to the phenotype of familial DP. We performed whole-exome sequencing in 67 pedigrees (125 individuals with DP and 35 unaffected controls) from our unique cohort of familial self-limited DP. Using a whole-exome sequencing filtering pipeline one candidate gene [fat mass and obesity-associated gene (FTO)] was identified. In silico, in vitro, and mouse model studies were performed to investigate the pathogenicity of FTO variants and timing of puberty in FTO+/- mice. We identified potentially pathogenic, rare variants in genes in linkage disequilibrium with genome-wide association studies of age at menarche loci in 283 genes. Of these, five genes were implicated in the control of body mass. After filtering for segregation with trait, one candidate, FTO, was retained. Two FTO variants, found in 14 affected individuals from three families, were also associated with leanness in these patients with DP. One variant (p.Leu44Val) demonstrated altered demethylation activity of the mutant protein in vitro. Fto+/- mice displayed a significantly delayed timing of pubertal onset (P < 0.05). Mutations in genes implicated in body mass and timing of puberty in the general population may contribute to the pathogenesis of self-limited DP. Copyright © 2017 Endocrine Society

Attenuation of the effect of the FTO rs9939609 polymorphism on total and central body fat by physical activity in adolescents: the HELENA study.

PubMed

Ruiz, Jonatan R; Labayen, Idoia; Ortega, Francisco B; Legry, Vanessa; Moreno, Luis A; Dallongeville, Jean; Martínez-Gómez, David; Bokor, Szilvia; Manios, Yannis; Ciarapica, Donatella; Gottrand, Frederic; De Henauw, Stefaan; Molnár, Denes; Sjöström, Michael; Meirhaeghe, Aline

2010-04-01

To examine whether physical activity attenuates the effect of the FTO rs9939609 polymorphism on body fat estimates in adolescents. Cross-sectional study. Athens, Greece; Dortmund, Germany; Ghent, Belgium; Heraklion, Greece; Lille, France; Pécs, Hungary; Rome, Italy; Stockholm, Sweden; Vienna, Austria; and Zaragoza, Spain, from October 2006 to December 2007. Adolescents from the Healthy Lifestyle in Europe by Nutrition in Adolescence Cross-Sectional Study (n = 752). Physical activity. The FTO rs9939609 polymorphism was genotyped. Physical activity was assessed by accelerometry. We measured weight, height, waist circumference, and triceps and subscapular skinfolds; body mass index (BMI [calculated as weight in kilograms divided by height in meters squared]) and body fat percentage were calculated. The A allele of the FTO polymorphism was significantly associated with higher BMI (+0.42 per risk allele), higher body fat percentage (+1.03% per risk allele), and higher waist circumference (+0.85 cm per risk allele). We detected significant or borderline gene x physical activity interactions for the studied body fat estimates (for interaction, P = .02, .06, and .10 for BMI, body fat percentage, and waist circumference, respectively). Indeed, the effect of the FTO rs9939609 polymorphism on these body fat parameters was much lower in adolescents who met the daily physical activity recommendations (ie, >/=60 min/d of moderate to vigorous physical activity) compared with those who did not: +0.17 vs +0.65 per risk allele in BMI, respectively; +0.40% vs +1.70% per risk allele in body fat percentage, respectively; and +0.60 vs +1.15 cm per risk allele in waist circumference, respectively. Adolescents meeting the daily physical activity recommendations may overcome the effect of the FTO rs9939609 polymorphism on obesity-related traits.

FTO variant, energy intake, physical activity and basal metabolic rate in Caucasians. The HAPIEE study.

PubMed

Hubáček, J A; Pikhart, H; Peasey, A; Kubínová, R; Bobák, M

2011-01-01

The FTO gene variants are the most important genetic determinants of body weight and obesity known so far, but the mechanism of their effect remains unclear. We have analyzed FTO rs17817449 variant (G>T in first intron) in 6024 adults aged 45-69 years to assess the potential mediating role of diet and physical activity. Diet was assessed by a 140-item food frequency questionnaire. Physical activity was measured by hours spent during a typical week by sport, walking and other activities outside of work requiring heavy and medium physical activity. Basal metabolic rate was calculated according Schofield formula. The FTO variant was significantly associated with body mass index (means in GG, GT and TT carriers were 28.7, 28.2 and 27.8 kg/m(2), p<0.001) and basal metabolic rate (BMR) (means in GG, GT and TT were 1603, 1588 and 1576 kcal per day, respectively, p<0.008) but it was not associated with physical activity, total energy intake or with energy intakes from fat, carbohydrates, proteins or alcohol. Results were essentially similar in men and women and the adjustment for physical activity or dietary energy intake did not reduce the effect of the FTO polymorphism. Means of BMR per kg of body weight was lowest in GG carriers (20.09, 20.21 for GT and 20.30 for TT, p<0.006) and this effect was more pronounced in females. These results suggest that the effect of the FTO rs17817449 variant on BMI in Caucasian adults is not mediated by energy intake or physical activity, but some effect on BMR per kg of body weight is possible.

The FTO variant is associated with chronic complications of diabetes mellitus in Czech population.

PubMed

Hubacek, Jaroslav A; Dlouha, Dana; Klementova, Marta; Lanska, Vera; Neskudla, Tomas; Pelikanova, Terezie

2018-02-05

Genome-wide association studies have resulted in the identification of the FTO gene as an important genetic determinant of diabetes mellitus. The aim of this study was to confirm the role of this gene in the development of DM in the Czech-Slavonic population and to analyse whether this gene is associated with common DM complications. Two groups of patients (814 with T1DM and 848 with T2DM) and a group of healthy controls (2339 individuals) - both of Czech origin - were genotyped for the FTO rs17817449 SNP. ANOVA and logistic regression were used for the statistical evaluations. The frequency of the GG genotype was significantly higher in T2DM (25.4% vs. 16.7%, P<0.0005) but not in T1DM patients (19.3% vs. 16.7%, P=0.20) than in controls. The increased risk of development of diabetic nephropathy was observed both for T1DM patients (GG vs. TT homozygotes, P<0.01) and T2DM patients (G carriers vs. TT homozygotes, P<0.05). FTO genotype predicted the development of diabetic neuropathy (GG vs. TT comparison; P<0.01) in the T2DM patients only. No association between FTO genotype and development of retinopathy was detected. All presented values are after adjustment for age, sex, BMI and duration of diabetes. We confirm the association between the FTO rs17817449 SNP and susceptibility to T2DM in the Czech-Slavonic population. The same variant is associated with a spectrum of chronic complications in both types of diabetes. Copyright © 2017 Elsevier B.V. All rights reserved.

Association between LEPR, FTO, MC4R, and PPARG-2 polymorphisms with obesity traits and metabolic phenotypes in school-aged children.

PubMed

Almeida, Sílvia M; Furtado, José M; Mascarenhas, Paulo; Ferraz, Maria E; Ferreira, José C; Monteiro, Mariana P; Vilanova, Manuel; Ferraz, Fernando P

2018-06-01

Evaluate the relationship of leptin receptor (LEPR) rs1137101, fat mass obesity-associated (FTO) receptors 9939609, melanocortin-4 receptors (MC4R) rs2229616 and rs17782313, and proliferator-activated receptor-gamma (PPARG) rs1801282 with clinical and metabolic phenotypes in prepubertal children. What is the effect of polymorphisms on clinical and metabolic phenotypes in prepubertal children? A cross-sectional descriptive study was performed to evaluate anthropometric features, percentage body fat (%BF), biochemical parameters, and genotype in 773 prepubertal children. FTO rs9939609 was associated with an increase in body mass index (BMI) and BMI z-score (zBMI). MC4R rs17782313 was associated with a decrease in BMI and +0.06 units in zBMI. LEPR, and PPARG-2 polymorphisms were associated with decreases in BMI and an increase and decrease units in zBMI, respectively. The homozygous SNPs demonstrated increases (FTO rs993609 and MC4R rs17782313) and decreases (LEPR rs1137101, PPARG rs1801282) in zBMI than the homozygous form of the major allele. In the overweight/obese group, the MC4R rs17782313 CC genotype showed higher average weight, zBMI, waist circumference, waist-circumference-to-height ratio, and waist-hip ratio, and lower BMI, mid-upper arm circumference, calf circumference, and %BF (P< 0.05). FTO rs9939609 AT and AA genotypes were associated with lower triglycerides (P < 0.05). We showed that MC4R rs17782313 and FTO rs9939609 were positively associated with zBMI, with weak and very weak effects, respectively, suggesting a very scarce contribution to childhood obesity. LEPR rs1137101 and PPARG-2 rs1801282 had weak and medium negative effects on zBMI, respectively, and may slightly protect against childhood obesity.

FTO Genetic Variation and Association With Obesity in West Africans and African Americans

PubMed Central

Adeyemo, Adebowale; Chen, Guanjie; Zhou, Jie; Shriner, Daniel; Doumatey, Ayo; Huang, Hanxia; Rotimi, Charles

2010-01-01

OBJECTIVE The FTO gene is one of the most consistently replicated loci for obesity. However, data from populations of African ancestry are limited. We evaluated genetic variation in the FTO gene and investigated associations with obesity in West Africans and African Americans. RESEARCH DESIGN AND METHODS The study samples comprised 968 African Americans (59% female, mean age 49 years, mean BMI 30.8 kg/m2) and 517 West Africans (58% female, mean age 54 years, mean BMI 25.5 kg/m2). FTO genetic variation was evaluated by genotyping 262 tag single nucleotide polymorphisms (SNPs) across the entire gene. Association of each SNP with BMI, waist circumference, and percent fat mass was investigated under an additive model. RESULTS As expected, both African-ancestry samples showed weaker linkage disequilibrium (LD) patterns compared with other continental (e.g., European) populations. Several intron 8 SNPs, in addition to intron 1 SNPs, showed significant associations in both study samples. The combined effect size for BMI for the top SNPs from meta-analysis was 0.77 kg/m2 (P = 0.009, rs9932411) and 0.70 kg/m2 (P = 0.006, rs7191513). Two previously reported associations with intron 1 SNPs (rs1121980 and rs7204609, r2 = 0.001) were replicated among the West Africans. CONCLUSIONS The FTO gene shows significant differences in allele frequency and LD patterns in populations of African ancestry compared with other continental populations. Despite these differences, we observed evidence of associations with obesity in African Americans and West Africans, as well as evidence of heterogeneity in association. More studies of FTO in multiple ethnic groups are needed. PMID:20299471

Differential distribution and association of FTO rs9939609 gene polymorphism with obesity: A cross-sectional study among two tribal populations of India with East-Asian ancestry.

PubMed

Ningombam, Somorjit Singh; Chhungi, Varhlun; Newmei, Masan Kambo; Rajkumari, Sunanda; Devi, Naorem Kiranmala; Mondal, Prakash Ranjan; Saraswathy, Kallur Nava

2018-03-20

The fat mass and obesity associated (FTO) rs9939609 gene polymorphism is most widely studied in terms of obesity in various populations. Recently, the prevalence of obesity has been reported to be very high among the North-Eastern State of India. The major aim of the present study is to understand the extent of FTO rs9939609 gene polymorphism and its association with obesity among the two North-East Indian tribal populations with similar East Asian ancestry. Somatometric data and fasting blood sample were collected from 521 tribal individuals (258 Liangmai and 263 Mizo) of Manipur after obtaining written informed consent. Genotyping of FTO rs9939609 single nucleotide polymorphism (SNP) was done using restriction fragment length polymorphism method for PCR-amplified fragments. Both the presently studied populations were not following Hardy-Weinberg law. The prevalence of obesity and minor allele frequency of FTO rs9939609 polymorphism was found to be significantly higher among the Mizo tribe compared to that of Liangmai. The selected polymorphism was found to be significantly associated with obesity (BMI) only among the Liangmai tribe (Odds ratio-3.0; 95% CI-1.4, 6.4; p-0.003), after adjusting for age and occupation. Age-cohort wise distribution and absolute fitness analysis indicated the lower fitness of minor allele in the higher age group among the Liangmai tribe. To the best of the author's knowledge this is the first study, associating FTO rs9939609 gene polymorphism and obesity in the North-eastern Indian tribal populations with East-Asian ancestry. This study revealed the FTO rs9939609 polymorphism is observed to be associated with obesity only among the Liangmai tribe not among the Mizo tribe. The differential distribution and association observed in the two selected tribes, inhabited in a similar geographical region, could be attributed to differences in their migratory histories in terms of both route and time of settlement. Copyright © 2018 Elsevier B.V. All rights reserved.

Ceramic with preferential oxygen reactive layer

NASA Technical Reports Server (NTRS)

Wang, Hongyu (Inventor); Luthra, Krishan Lal (Inventor)

2001-01-01

An article comprises a silicon-containing substrate and an external environmental/thermal barrier coating. The external environmental/thermal barrier coating is permeable to diffusion of an environmental oxidant and the silicon-containing substrate is oxidizable by reaction with oxidant to form at least one gaseous product. The article comprises an intermediate layer/coating between the silicon-containing substrate and the environmental/thermal barrier coating that is oxidizable to a nongaseous product by reaction with the oxidant in preference to reaction of the silicon-containing substrate with the oxidant. A method of forming an article, comprises forming a silicon-based substrate that is oxidizable by reaction with oxidant to at least one gaseous product and applying an intermediate layer/coating onto the substrate, wherein the intermediate layer/coating is oxidizable to a nongaseous product by reaction with the oxidant in preference to reaction of the silicon-containing substrate with the oxidant.

FTO genotype and 2-year change in body composition and fat distribution in response to weight-loss diets: the POUNDS LOST Trial.

PubMed

Zhang, Xiaomin; Qi, Qibin; Zhang, Cuilin; Smith, Steven R; Hu, Frank B; Sacks, Frank M; Bray, George A; Qi, Lu

2012-11-01

Recent evidence suggests that the fat mass and obesity-associated gene (FTO) genotype may interact with dietary intakes in relation to adiposity. We tested the effect of FTO variant on weight loss in response to 2-year diet interventions. FTO rs1558902 was genotyped in 742 obese adults who were randomly assigned to one of four diets differing in the proportions of fat, protein, and carbohydrate. Body composition and fat distribution were measured by dual-energy x-ray absorptiometry and computed tomography. We found significant modification effects for intervention varying in dietary protein on 2-year changes in fat-free mass, whole body total percentage of fat mass, total adipose tissue mass, visceral adipose tissue mass, and superficial adipose tissue mass (for all interactions, P < 0.05). Carriers of the risk allele had a greater reduction in weight, body composition, and fat distribution in response to a high-protein diet, whereas an opposite genetic effect was observed on changes in fat distribution in response to a low-protein diet. Likewise, significant interaction patterns also were observed at 6 months. Our data suggest that a high-protein diet may be beneficial for weight loss and improvement of body composition and fat distribution in individuals with the risk allele of the FTO variant rs1558902.

Association between FTO polymorphism in exon 3 with carcass and meat quality traits in crossbred ducks.

PubMed

Gan, W; Song, Q; Zhang, N N; Xiong, X P; Wang, D M C; Li, L

2015-06-18

The fat mass and obesity-associated gene (FTO) is an excellent candidate gene that affects energy metabolism. Single nucleotide polymorphisms (SNPs) in FTO are associated with carcass and meat quality traits in pigs, cattle, and rabbits. The aim of this study was to investigate the association between novel SNPs in the FTO coding region and carcass and meat quality traits in 95 crossbred ducks, using DNA sequencing. We found two transitions G/A (SNP 387 and 473) within exon 3. SNP 387 was a synonymous mutation, whereas SNP 473 was a missense mutation. Association analysis suggested that SNP g.387G>A was significantly associated with all of the carcass traits measured, the intramuscular fat content (IMF), cooking yield (CY), pH values 45 min after slaughter (pH45m), drip losses from the breast muscle, and the leg muscle (P < 0.05). For SNP g.473G>A, the genotype AA exhibited greater leg muscle weight than the genotypes GG or AG (P < 0.05). The D value suggested that the two SNPs exhibited strong linkage disequilibrium. Three haplotypes (G1G2, G1A2, and A1A2) were significantly associated with IMF, CY, the a* value, and all of the carcass traits measured (P < 0.05). The results suggest that FTO is a candidate locus that affects carcass and meat quality traits in ducks.

Obesity-related genetic variants, human pigmentation, and risk of melanoma

PubMed Central

Li, Xin; Liang, Liming; Zhang, Mingfeng; Song, Fengju; Nan, Hongmei; Wang, Li-E; Wei, Qingyi; Lee, Jeffrey E.; Amos, Christopher I.; Qureshi, Abrar A.; Han, Jiali

2013-01-01

Previous biological studies showed evidence of a genetic link between obesity and pigmentation in both animal models and humans. Our study investigated the individual and joint associations between obesity-related single nucleotide polymorphisms (SNPs) and both human pigmentation and risk of melanoma. Eight obesity-related SNPs in the FTO, MAP2K5, NEGR1, FLJ35779, ETV5, CADM2, and NUDT3 genes were nominally significantly associated with hair color among 5,876 individuals of European ancestry. The genetic score combining 35 independent obesity-risk loci was significantly associated with darker hair color (beta-coefficient per ten alleles=0.12, P-value=4 10−5). However, single SNPs or genetic scores showed non-significant association with tanning ability. We further examined the SNPs at the FTO locus for their associations with pigmentation and risk of melanoma. Among the 783 SNPs in the FTO gene with imputation R-square quality metric >0.8 using the 1000 genome data set, ten and three independent SNPs were significantly associated with hair color and tanning ability respectively. Moreover, five independent FTO SNPs showed nominally significant association with risk of melanoma in 1,804 cases and 1,026 controls. But none of them was associated with obesity or in linkage disequilibrium with obesity-related variants. FTO locus may confer variation in human pigmentation and risk of melanoma, which may be independent of its effect on obesity. PMID:23539184

Association between ACE (rs4646994), FABP2 (rs1799883), MTHFR (rs1801133), FTO (rs9939609) Genes Polymorphism and Type 2 Diabetes with Dyslipidemia.

PubMed

Raza, Syed Tasleem; Abbas, Shania; Siddiqi, Zeba; Mahdi, Farzana

2017-01-01

Diabetic dyslipidemia is one of the leading causes of coronary artery disease (CAD) death. Genetic and environmental factors play an important role in the development of type 2 diabetes mellitus (T2DM) and dyslipidemia. The present study was aimed to investigate the association of ACE (rs4646994), FABP2 (rs1799883), MTHFR (rs1801133) and FTO (rs9939609) genes polymorphism in T2DM with dyslipidemia. Totally, 559 subjects including 221 T2DM cases with dyslipidemia, 158 T2DM without dyslipidemia and 180 controls were enrolled. ACE genes polymorphism was evaluated by polymerase chain reaction (PCR), while MTHFR , FABP2 , FTO genes polymorphisms were evaluated by PCR and restriction fragment length polymorphism (RFLP). Significant association of ACE and MTHFR genes polymorphisms were found in both group of cases [T2DM with dyslipidemia (P<0.001, and P=0.008, respectively) and T2DM without dyslipidemia (P=0.003, and P=0.010, respectively)] while FABP2 and FTO genes polymorphisms were significantly associated with T2DM without dyslipidemia (P=0.038, and P= 0.019, respectively). This study concludes that ACE , FABP2 , FTO and MTHFR genes are associated with T2DM. Additionally, it also seems that ACE and MTHFR genes might be further associated with the development of dyslipidemia in T2DM cases.

Effect of bath temperature on structure, morphology and thermoelectric properties of CoSb{sub 3} thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yadav, Suchitra, E-mail: suchitrayadav87@gmail.com; Pandya, Dinesh K.; Chaudhary, Sujeet

2016-05-23

CoSb{sub 3} thin films are deposited on conducting glass substrates (FTO) by electrodeposition at different bath temperatures (60°C, 70°C and 80°C) and the resulting influence of the bath temperature on the structure, morphology and electrical properties of films is investigated. X-ray diffraction confirms the formation of CoSb{sub 3} phase in the films. Scanning electron microscopy reveals that different morphologies ranging from branched nano-flakes to nano-needles evolve as bath temperature increases. It is concluded that a growth temperature of 80°C is suitable for producing CoSb{sub 3} films with such properties that show potential feasibility for thermoelectric applications.

Electrical properties of graphene film for counter electrode in dye sensitized solar cells

NASA Astrophysics Data System (ADS)

Khalifa, Ali; Shafie, S.; Hasan, W. Z. W.; Lim, H. N.; Rusop, M.; Samaila, Buda

2018-05-01

A graphene counter electrode for dye-sensitized solar cell was prepared simply by drop casting method on a conducting FTO glass at room temperature. Raman spectroscopy was used to study the defection in the graphene films. The sheet resistance was also measured and recoded minimum value of 7.04 Ω/□ at 22.19µm thickness. The casted films show good adhesion to substrates with low defects. A DSSC based on graphene counter electrode demonstrates reasonable conversion efficiency of 2.78% with short circuit current of 7.60mA, open circuit voltage of 0.69V and fill factor of 0.52. The high conductivity and low defects render the prepared graphene dispersion for DSSCs' CE application.

An enhanced mangiferaindica for dye sensitized solar cell application

NASA Astrophysics Data System (ADS)

Uno, U. E.; Emetere, M. E.; Fadipe, L. A.; Oluranti, Jonathan

2016-02-01

Titanium dioxide (T1O2) is preferred to Zinc oxide as mesoporous oxide layer because it raised the efficiency of DSSCs from 1% to 7%. The chemistry of the process however seem rigorous to allow the light induced electron injection from the adsorbed dye into the nanocrystallites i.e. which renders the TiO2 conductive. The DSSC fabricated consist of 2.25 cm2 active area of titanium dioxide coated on FTO glass (fluorine tin oxide) immersed in ethanol solution of natural dye extracted as an anode (electrode) and counter electrode. These two electrodes were coupled together and the space between them was filled with the Iodolyte AN-50 as solid electrolyte or redox mediator. The photo electrochemical parameters of the dye extracted (Mango fruit Peel) from the results obtained are short circuit current (Isc)= 1.22×10-2, current density (Jsc)=4.07×10-2, open circuit voltage (voc) =0.53V, fill factor (FF) of 0.16 and the overall conversion efficiency (Eff) =0.345%.

Effect of multiple deposition of NiO layer on the performance of inverted type organic solar cell based on ZnO/P3HT:PCBM

NASA Astrophysics Data System (ADS)

Sabri, Nasehah Syamin; Lim, Eng Liang; Yap, Chi Chin; Yahaya, Muhammad; Salleh, Muhamad Mat; Jumali, Mohammad Hafizuddin Haji

2017-05-01

In this work, the effect of multiple deposition of nickel oxide (NiO) hole transport layer (HTL) on the performance of inverted type organic solar cell with a configuration of fluorine tin oxide (FTO)/zinc oxide (ZnO) nanorods/ poly(3-hexylthiopene):[6,6]-phenyl-C61-butyric acid methyl ester (P3HT:PCBM)/NiO/silver (Ag) was investigated. The NiO nanoparticles solution was spin-coated on top of the photoactive layer (P3HT:PCBM) prior to deposition of Ag electrode. Different numbers of NiO layers (1, 2, and 4) were deposited on the photoactive layer to obtain the optimum surface morphology of HTL. The device with 2 layers of NiO exhibited the optimum power conversion efficiency of 1.10%. It is believed that the optimum NiO deposition layer gives the complete coverage at photoactive layer and forms ohmic contact between the photoactive layer and Ag electrode.

Method for producing high quality oxide films on substrates

DOEpatents

Ruckman, Mark W.; Strongin, Myron; Gao, Yong L.

1993-01-01

A method for providing an oxide film of a material on the surface of a substrate using a reactive deposition of the material onto the substrate surface in the presence of a solid or liquid layer of an oxidizing gas. The oxidizing gas is provided on the substrate surface in an amount sufficient to dissipate the latent heat of condensation occurring during deposition as well as creating a favorable oxidizing environment for the material.

High quality oxide films on substrates

DOEpatents

Ruckman, Mark W.; Strongin, Myron; Gao, Yong L.

1994-01-01

A method for providing an oxide film of a material on the surface of a substrate using a reactive deposition of the material onto the substrate surface in the presence of a solid or liquid layer of an oxidizing gas. The oxidizing gas is provided on the substrate surface in an amount sufficient to dissipate the latent heat of condensation occurring during deposition as well as creating a favorable oxidizing environment for the material.

Articles including thin film monolayers and multilayers

DOEpatents

Li, DeQuan; Swanson, Basil I.

1995-01-01

Articles of manufacture including: (a) a base substrate having an oxide surface layer, and a multidentate ligand, capable of binding a metal ion, attached to the oxide surface layer of the base substrate, (b) a base substrate having an oxide surface layer, a multidentate ligand, capable of binding a metal ion, attached to the oxide surface layer of the base substrate, and a metal species attached to the multidentate ligand, (c) a base substrate having an oxide surface layer, a multidentate ligand, capable of binding a metal ion, attached to the oxide surface layer of the base substrate, a metal species attached to the multidentate ligand, and a multifunctional organic ligand attached to the metal species, and (d) a base substrate having an oxide surface layer, a multidentate ligand, capable of binding a metal ion, attached to the oxide surface layer of the base substrate, a metal species attached to the multidentate ligand, a multifunctional organic ligand attached to the metal species, and a second metal species attached to the multifunctional organic ligand, are provided, such articles useful in detecting the presence of a selected target species, as nonliear optical materials, or as scavengers for selected target species.

Overlay coating degradation by simultaneous oxidation and coating/substrate interdiffusion. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Nesbitt, J. A.

1983-01-01

Degradation of NiCrAlZr overlay coatings on various NiCrAl substrates was examined after cyclic oxidation. Concentration/distance profiles were measured in the coating and substrate after various oxidation exposures at 1150 C. For each stubstrate, the Al content in the coating decreased rapidly. The concentration/distance profiles, and particularly that for Al, reflected the oxide spalling resistance of each coated substrate. A numerical model was developed to simulate diffusion associated with overlay-coating degradation by oxidation and coating/substrate interdiffusion. Input to the numerical model consisted of the Cr and Al content of the coating and substrate, ternary diffusivities, and various oxide spalling parameters. The model predicts the Cr and Al concentrations in the coating and substrate after any number of oxidation/thermal cycles. The numerical model also predicts coating failure based on the ability of the coating to supply sufficient Al to the oxide scale. The validity of the model was confirmed by comparison of the predicted and measured concentration/distance profiles. The model was subsequently used to identify the most critical system parameters affecting coating life.

Optically transparent FTO-free cathode for dye-sensitized solar cells.

PubMed

Kavan, Ladislav; Liska, Paul; Zakeeruddin, Shaik M; Grätzel, Michael

2014-12-24

The woven fabric containing electrochemically platinized tungsten wire is an affordable flexible cathode for liquid-junction dye-sensitized solar cells with the I3(-)/I(-) redox mediator and electrolyte solution consisting of ionic liquids and propionitrile. The fabric-based electrode outperforms the thermally platinized FTO in serial ohmic resistance and charge-transfer resistance for triiodide reduction, and it offers comparable or better optical transparency in the visible and particularly in the near-IR spectral region. The electrode exhibits good stability during electrochemical loading and storage at open circuit. The dye-sensitized solar cells with a C101-sensitized titania photoanode and either Pt-W/PEN or Pt-FTO cathodes show a comparable performance.

Experimental and Modeling Studies on the Microstructures and Properties of Oxidized Aluminum Nitride Ceramic Substrates

NASA Astrophysics Data System (ADS)

Cao, Ye; Xu, Haixian; Zhan, Jun; Zhang, Hao; Wei, Xin; Wang, Jianmin; Cui, Song; Tang, Wenming

2018-05-01

Oxidation of aluminum nitride (AlN) ceramic substrates doped with 2 wt.% Y2O3 was performed in air at temperatures ranging from 1000 to 1300 °C for various lengths of time. Microstructure, bending strength, and thermal conductivity of the oxidized AlN substrates were studied experimentally and also via mathematical models. The results show that the oxide layer formed on the AlN substrates is composed of α-Al2O3 nanocrystallines and interconnected micropores. Longitudinal and transverse cracks are induced in the oxide layer under tensile and shear stresses, respectively. Intergranular oxidation of the AlN grains close to the oxide layer/AlN interface also occurs, leading to widening and cracking of the AlN grain boundaries. These processes result in the monotonous degradation of bending strength and thermal conductivity of the oxidized AlN substrates. Two mathematic models concerning these properties of the oxidized AlN substrates versus the oxide layer thickness were put forward. They fit well with the experimental results.

High quality oxide films on substrates

DOEpatents

Ruckman, M.W.; Strongin, M.; Gao, Y.L.

1994-02-01

A method is described for providing an oxide film of a material on the surface of a substrate using a reactive deposition of the material onto the substrate surface in the presence of a solid or liquid layer of an oxidizing gas. The oxidizing gas is provided on the substrate surface in an amount sufficient to dissipate the latent heat of condensation occurring during deposition as well as creating a favorable oxidizing environment for the material. 4 figures.

Method for producing high quality oxide films on substrates

DOEpatents

Ruckman, M.W.; Strongin, M.; Gao, Y.L.

1993-11-23

A method is described for providing an oxide film of a material on the surface of a substrate using a reactive deposition of the material onto the substrate surface in the presence of a solid or liquid layer of an oxidizing gas. The oxidizing gas is provided on the substrate surface in an amount sufficient to dissipate the latent heat of condensation occurring during deposition as well as creating a favorable oxidizing environment for the material. 4 figures.

The FTO gene polymorphism (rs9939609) is associated with metabolic syndrome in morbidly obese subjects from southern Italy.

PubMed

Liguori, Rosario; Labruna, Giuseppe; Alfieri, Andreina; Martone, Domenico; Farinaro, Eduardo; Contaldo, Franco; Sacchetti, Lucia; Pasanisi, Fabrizio; Buono, Pasqualina

2014-08-01

Gene variants in MC4R, SIRT1 and FTO are associated with severe obesity and metabolic impairment in Caucasians. We investigated whether common variants in these genes are associated with metabolic syndrome (MetS) in a large group of morbidly obese young adults from southern Italy. One thousand morbidly obese subjects (62% women, mean body mass index 46.5 kg/m(2), mean age 32.6 years) whose families had lived in southern Italy for at least 2 generations were recruited. Single-nucleotide polymorphisms (SNPs) rs12970134, rs477181, rs502933 (MC4R locus), rs3818292, rs7069102, rs730821, rs2273773, rs12413112 (SIRT1 locus) and rs1421085, rs9939609, 9930506, 1121980 (FTO locus) were genotyped by Taqman assay; blood parameters were assayed by routine methods; the Fat Mass, Fat Free Mass, Respiratory Quotient, Basal Metabolic Rate (BMR) and waist circumference were also determined. Binomial logistic regression showed that the TA heterozygous genotype of SNP rs9939609 in the FTO gene was associated with the presence of MetS in our population [OR (95% CI): 2.53 (1.16-5.55)]. Furthermore, the FTO rs9939609 genotype accounted for 21.3% of the MetS phenotype together with total cholesterol, BMR and age. Our results extend the knowledge on genotype susceptibility for MetS in relation to a specific geographical area of residence. Copyright © 2014 Elsevier Ltd. All rights reserved.

Dietary fatty acid distribution modifies obesity risk linked to the rs9939609 polymorphism of the fat mass and obesity-associated gene in a Spanish case-control study of children.

PubMed

Moleres, Adriana; Ochoa, M Carmen; Rendo-Urteaga, Tara; Martínez-González, M Angel; Azcona San Julián, M Cristina; Martínez, J Alfredo; Marti, Amelia

2012-02-01

The rs9939609 polymorphism of the fat mass and obesity-associated (FTO) gene has been widely associated with childhood obesity in several European cohorts. This association appears to be dependent on dietary macronutrients. Therefore, the aim of the present study was to evaluate whether dietary fatty acid intake distribution could interact with this FTO genetic variation and obesity in a Spanish case-control study of children and adolescents. A total of 354 Spanish children and adolescents aged 6-18 years (49 % males) were genotyped for the rs9939609 variant of the FTO gene. Anthropometric parameters were taken and energy intake was measured. We observed an interaction between the consumption of SFA (percentage of total energy) and PUFA:SFA ratio and obesity risk linked to the rs9939609 SNP of the FTO gene. In the study population of the present study, the risk allele carriers consuming more than 12·6 % SFA (of total energy) had an increased obesity risk compared with TT carriers. In a similar way, A allele carriers with an intake ratio lower than 0·43 PUFA:SFA presented a higher obesity risk than TT subjects. In summary, the present study reports for the first time the influence of dietary fatty acid distribution on the effect of the rs9939609 polymorphism of the FTO gene on children and adolescents' obesity risk.

MgO Nanoparticle Modified Anode for Highly Efficient SnO2-Based Planar Perovskite Solar Cells.

PubMed

Ma, Junjie; Yang, Guang; Qin, Minchao; Zheng, Xiaolu; Lei, Hongwei; Chen, Cong; Chen, Zhiliang; Guo, Yaxiong; Han, Hongwei; Zhao, Xingzhong; Fang, Guojia

2017-09-01

Reducing the energy loss and retarding the carrier recombination at the interface are crucial to improve the performance of the perovskite solar cell (PSCs). However, little is known about the recombination mechanism at the interface of anode and SnO 2 electron transfer layer (ETL). In this work, an ultrathin wide bandgap dielectric MgO nanolayer is incorporated between SnO 2 :F (FTO) electrode and SnO 2 ETL of planar PSCs, realizing enhanced electron transporting and hole blocking properties. With the use of this electrode modifier, a power conversion efficiency of 18.23% is demonstrated, an 11% increment compared with that without MgO modifier. These improvements are attributed to the better properties of MgO-modified FTO/SnO 2 as compared to FTO/SnO 2 , such as smoother surface, less FTO surface defects due to MgO passivation, and suppressed electron-hole recombinations. Also, MgO nanolayer with lower valance band minimum level played a better role in hole blocking. When FTO is replaced with Sn-doped In 2 O 3 (ITO), a higher power conversion efficiency of 18.82% is demonstrated. As a result, the device with the MgO hole-blocking layer exhibits a remarkable improvement of all J-V parameters. This work presents a new direction to improve the performance of the PSCs based on SnO 2 ETL by transparent conductive electrode surface modification.

Association of fat mass and obesity-associated and retinitis pigmentosa guanosine triphosphatase (GTPase) regulator-interacting protein-1 like polymorphisms with body mass index in Chinese women.

PubMed

Chen, Boyu; Li, Zhiqiang; Chen, Jianhua; Ji, Jue; Shen, Jingyi; Xu, Yufeng; Zhao, Yingying; Liu, Danping; Shen, Yinhuan; Zhang, Weijie; Shen, Jiawei; Wang, Yonggang; Shi, Yongyong

2018-04-14

Body mass index (BMI) is the most commonly used quantitative measure of adiposity. It is a kind of complex genetic diseases which are caused by multiple susceptibility genes. The first intron of fat mass and obesity-associated (FTO) has been widely discovered to be associated with BMI. Retinitis pigmentosa GTPase regulator-interacting protein-1 like (RPGRIP1L) is located in the upstream region of FTO and has been proved to be linked with obesity through functional tests. We carried out a genetic association analysis to figure out the role of the FTO gene and the RPGRIP1L gene in BMI. A quantitative traits study with 6,102 Chinese female samples, adjusted for age, was performed during our project. Among the twelve SNPs, rs1421085, rs1558902, rs17817449, rs8050136, rs9939609, rs7202296, rs56137030, rs9930506 and rs12149832 in the FTO gene were significantly associated with BMI after Bonferroni correction. Meanwhile, rs9934800 in the RPGRIP1L gene showed significance with BMI before Bonferroni correction, but this association was eliminated after Bonferroni correction. Our results suggested that genetic variants in the FTO gene were strongly associated with BMI in Chinese women, which may serve as targets of pharmaceutical research and development concerning BMI. Meanwhile, we didn't found the significant association between RPGRIP1L and BMI in Chinese women.

Are obesity risk genes associated with binge eating in adolescence?

PubMed Central

Micali, Nadia; Field, Alison E; Treasure, Janet L; Evans, David M

2015-01-01

Objective Cognitions and behaviors characteristic of binge eating are associated with a polymorphism in the FTO gene, robustly related to body mass index (BMI) and obesity risk. We investigated the association between binge eating and the individual and combined effect of 32 SNPs robustly associated with BMI in a population-based sample. We hypothesized that higher BMI and binge eating might share a common genetic etiology. Methods Binge eating was assessed in adolescents from the Avon Longitudinal Study of Parents and Children at age 14 (n = 5,958) and 16 years (n = 4,948). We tested associations between 32 BMI-related SNPs and binge eating in crude and BMI-, age-, and gender-adjusted regression models. Results Crude analyses showed an association between binge eating and rs1558902 (FTO) that persisted after adjustment for BMI (OR = 1.20, P = 8 × 10−3). A weighted allelic score consisting of all 32 BMI-related SNPs was associated with binge eating (P = 8 × 10−4); this association attenuated (P = 0.08) when rs1558902 was removed from the weighted allelic score. Conclusions BMI-related genes are associated with adolescent binge eating, in particular an FTO polymorphism. Although replication is needed, our findings have biological plausibility and are consistent with a postulated effect of FTO on appetite and food intake. Future studies should aim to understand the mechanisms underlying the relationship between FTO, binge eating, and obesity. PMID:26193063

The role of early life growth development, the FTO gene and exclusive breastfeeding on child BMI trajectories.

PubMed

Wu, Yan Yan; Lye, Stephen; Briollais, Laurent

2017-10-01

Recent studies have implicated the FTO gene in child and adult obesity. A longer duration of exclusive breastfeeding (EXBF) has been shown to reduce body mass index (BMI) and the risk of being overweight in the general population and among FTO gene carriers. However, it remains unclear whether the preventive effect of EXBF could be explained by its impact on early life growth development, e.g. ages at adiposity peak (AP) and adiposity rebound (AR) and BMI velocities in the first years of life, which are major determinants of overweight and obesity later in life. We studied 5590 children from the British Avon Longitudinal Study of Parents and Children (ALSPAC) cohort and modelled their longitudinal BMI profiles with mixed effects models from birth to 16 years of age, as well as their ages at AP, AR and BMI velocities in relation to the FTO gene variant and EXBF. A longer duration of EXBF (i.e. at least 5 months) has substantial impact on BMI growth trajectories among children carrying the FTO adverse variant by modulating the age at AP, age at AR and BMI velocities. EXBF acts antagonistically to the FTO rs9939609 risk allele and by the age of 15, the predicted reduction in BMI after 5 months of EXBF is 0.56 kg/m2 [95% confidence interval (CI) 0.11-1.01; P = 0.003] and 1.14 kg/m2 (95% CI 0.67-1.62; P < 0.0001) in boys and girls, respectively. EXBF influences early life growth development and thus plays a critical role in preventing the risks of overweight and obesity even when those are exacerbated by genetic factors. © The Author 2017; all rights reserved. Published by Oxford University Press on behalf of the International Epidemiological Association

Magnetic response of hybrid ferromagnetic and antiferromagnetic core-shell nanostructures

NASA Astrophysics Data System (ADS)

Khan, U.; Li, W. J.; Adeela, N.; Irfan, M.; Javed, K.; Wan, C. H.; Riaz, S.; Han, X. F.

2016-03-01

The synthesis of FeTiO3-Ni(Ni80Fe20) core-shell nanostructures by a two-step method (sol-gel and DC electrodeposition) has been demonstrated. XRD analysis confirms the rhombohedral crystal structure of FeTiO3(FTO) with space group R3&cmb.macr;. Transmission electron microscopy clearly depicts better morphology of nanostructures with shell thicknesses of ~25 nm. Room temperature magnetic measurements showed significant enhancement of magnetic anisotropy for the permalloy (Ni80Fe20)-FTO over Ni-FTO core-shell nanostructures. Low temperature magnetic measurements of permalloy-FeTiO3 core-shell structure indicated a strong exchange bias mechanism with magnetic coercivity below the antiferromagnetic Neel temperature (TN = 59 K). The exchange bias is attributed to the alignment of magnetic moments in the antiferromagnetic material at low temperature. Our scheme opens a path towards optimum automotive systems and wireless communications wherein broader bandwidths and smaller sizes are required.The synthesis of FeTiO3-Ni(Ni80Fe20) core-shell nanostructures by a two-step method (sol-gel and DC electrodeposition) has been demonstrated. XRD analysis confirms the rhombohedral crystal structure of FeTiO3(FTO) with space group R3&cmb.macr;. Transmission electron microscopy clearly depicts better morphology of nanostructures with shell thicknesses of ~25 nm. Room temperature magnetic measurements showed significant enhancement of magnetic anisotropy for the permalloy (Ni80Fe20)-FTO over Ni-FTO core-shell nanostructures. Low temperature magnetic measurements of permalloy-FeTiO3 core-shell structure indicated a strong exchange bias mechanism with magnetic coercivity below the antiferromagnetic Neel temperature (TN = 59 K). The exchange bias is attributed to the alignment of magnetic moments in the antiferromagnetic material at low temperature. Our scheme opens a path towards optimum automotive systems and wireless communications wherein broader bandwidths and smaller sizes are required. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr07946b

The study of the rs9939609 FTO gene polymorphism in association with obesity and the management of obesity in a Romanian cohort.

PubMed

Ursu, R I; Badiu, C; Cucu, N; Ursu, G F; Craciunescu, I; Severin, E

2015-01-01

The incidence of obesity especially in Romanian population is presently escalating as a major nutrition and health problem. Clinicians aided by scientists are engaged in research approaches that include heredity aspects linked with behavior, education, applied nutrition studies and clinical therapies in order to prevent, control and reverse obesity. The common goal is to identify areas of basic and clinical research to understand aspects of human biology that may be considered as obesogenic. Regarding these approaches, recent discoveries in genetics, epigenetics and functional genomics, based on advancing technologies, are tools employed to prevent and treat obesity. The purpose of this article is to present the current knowledge of key components of the FTO gene role in the obesogenic system that links genetic, epigenetic and environmental, lifestyle/ diet nutritional and behavioral components and to describe the results obtained by genotyping and interviewing relevant selected groups of Romanian population. FTO rs9939609 genotyping was performed on a Romanian study group of 53 subjects (30 obese, 23 normal). Results have been analyzed in association with obesity parameters and comorbidities in order to identify this polymorphism's effect on body mass in our Caucasian cohort. At the same time, personal history of the subjects in correlation with the FTO genotypes provided important information on the FTO gene's influence on the feeding behavior and food selection of these individuals. In conclusion, the FTO rs9939609 polymorphism has been identified as a common gene variant in our Romanian Caucasian cohort, proving a high association with all the parameters of obesity and obesity comorbidities. The adherence to a Mediterranean diet is benefic for subjects with genetic predisposition for this disorder as long as it is kept for a long period of time along with sustained physical exercise. Association studies are an extremely important tool in understanding the hunger-satiety pathway, providing information on the relation between obesity-related genes, gene expression and behavior.

Buffer layers for coated conductors

DOEpatents

Stan, Liliana [Los Alamos, NM; Jia, Quanxi [Los Alamos, NM; Foltyn, Stephen R [Los Alamos, NM

2011-08-23

A composite structure is provided including a base substrate, an IBAD oriented material upon the base substrate, and a cubic metal oxide material selected from the group consisting of rare earth zirconates and rare earth hafnates upon the IBAD oriented material. Additionally, an article is provided including a base substrate, an IBAD oriented material upon the base substrate, a cubic metal oxide material selected from the group consisting of rare earth zirconates and rare earth hafnates upon the IBAD oriented material, and a thick film upon the cubic metal oxide material. Finally, a superconducting article is provided including a base substrate, an IBAD oriented material upon the base substrate, a cubic metal oxide material selected from the group consisting of rare earth zirconates and rare earth hafnates upon the IBAD oriented material, and an yttrium barium copper oxide material upon the cubic metal oxide material.

Screening method for selecting semiconductor substrates having defects below a predetermined level in an oxide layer

DOEpatents

Warren, William L.; Vanheusden, Karel J. R.; Schwank, James R.; Fleetwood, Daniel M.; Shaneyfelt, Marty R.; Winokur, Peter S.; Devine, Roderick A. B.

1998-01-01

A method for screening or qualifying semiconductor substrates for integrated circuit fabrication. The method comprises the steps of annealing at least one semiconductor substrate at a first temperature in a defect-activating ambient (e.g. hydrogen, forming gas, or ammonia) for sufficient time for activating any defects within on oxide layer of the substrate; measuring a defect-revealing electrical characteristic of at least a portion of the oxide layer for determining a quantity of activated defects therein; and selecting substrates for which the quantity of activated defects is below a predetermined level. The defect-revealing electrical characteristic may be a capacitance-versus-voltage (C-V) characteristic or a current-versus-voltage (I-V) characteristic that is dependent on an electrical charge in the oxide layer generated by the activated defects. Embodiments of the present invention may be applied for screening any type of semiconductor substrate or wafer having an oxide layer formed thereon or therein. This includes silicon-on-insulator substrates formed by a separation by the implantation of oxygen (SIMOX) process or the bond and etch back silicon-on-insulator (BESOI) process, as well as silicon substrates having a thermal oxide layer or a deposited oxide layer.

Supercapacitors incorporating hollow cobalt sulfide hexagonal nanosheets

NASA Astrophysics Data System (ADS)

Yang, Zusing; Chen, Chia-Ying; Chang, Huan-Tsung

We have prepared hollow cobalt sulfide (CoS) hexagonal nanosheets (HNSs) from Co(NO 3) 2 and thioacetamide in the presence of poly(vinylpyrrolidone) (PVP) at 100 °C under alkaline condition. The as-prepared hollow CoS HNSs have an average edge length ca. 110 ± 27 nm and an outer shell of 16 ± 4 nm in thickness from 500 counts. The CoS HNSs are deposited onto transparent fluorine-doped tin oxide (FTO) substrates through a drop-dry process to prepare two types of supercapacitors (SCs); high rate and large per-area capacitance. The electrolyte used in this study is KOH (aq). The CoS HNSs (8 μg cm -2) electrodes exhibit excellent capacity properties, including high energy density (13.2 h kg -1), power density (17.5 kW kg -1), energy deliverable efficiency (81.3-85.3%), and stable cycle life (over 10,000 cycles) at a high discharge current density of 64.6 A g -1. With their fast charging and discharging rates (<3 s), the CoS HNSs show characteristics of high-rate SCs. The CoS HNS SCs having high mass loading (9.7 mg cm -2) provide high per-area capacitance of 1.35 F cm -2 and per-mass capacitance of 138 F g -1, respectively, showing characteristics of SCs with large per-area capacitance. Our results have demonstrated the potential of the CoS HNS electrodes hold great practical potential in many fields such as automobile and computer industries.

CdS-sensitized TiO2 nanocorals: hydrothermal synthesis, characterization, application.

PubMed

Mali, S S; Desai, S K; Dalavi, D S; Betty, C A; Bhosale, P N; Patil, P S

2011-10-01

Cadmium sulfide (CdS) nanoparticle-sensitized titanium oxide nanocorals (TNC) were synthesized using a two-step deposition process. The TiO(2) nanocorals were grown on the conducting glass substrates (FTO) using A hydrothermal process and CdS nanoparticles were loaded on TNC using successive ionic layer adsorption and reaction (SILAR) method. The TiO(2), CdS and TiO(2)-CdS samples were characterized by optical absorption, X-ray diffraction (XRD), FT-Raman, FT-IR, scanning electron microscopy (SEM) and contact angle. Further, their photoelectrochemical (PEC) performance was tested in NaOH, Na(2)S-NaOH-S and Na(2)S electrolytes, respectively. When CdS nanoparticles are coated on TNCs, the optical absorption is found to be enhanced and band edge is red-shifted towards visible region. The TiO(2)-CdS sample exhibits improved photoelectrochemical (PEC) performance with maximum short circuit current of (J(sc)) 1.04 mA cm(-2). After applying these TiO(2)-CdS electrodes in photovoltaic cells, the photocurrent was found to be enhanced by 2.7 and 32.5 times, as compared with those of bare CdS and TiO(2) nanocorals films electrodes respectively. Also, the power conversion efficiency of TiO(2)-CdS electrodes is 0.72%, which is enhanced by about 16 and 29 times for TiO(2), CdS samples. This journal is © The Royal Society of Chemistry and Owner Societies 2011

Synergetic effect of Sn addition and oxygen-deficient atmosphere to fabricate active hematite photoelectrodes for light-induced water splitting

NASA Astrophysics Data System (ADS)

Freitas, Andre L. M.; Souza, Flavio L.

2017-11-01

This work describes the design of a microwave-assisted method using hydrothermal conditions to fabricate pure and Sn-doped hematite photoelectrodes with varied synthesis time and additional thermal treatment under air and N2 atmosphere. The hematite photoelectrode formed under N2 atmosphere, with Sn deposited on its surface—which is represented by material synthesized at 4 h —exhibits the highest performance. Hence, Sn addition followed by high temperature annealing conducted in an oxygen-deficient atmosphere seems to create oxygen vacancies, and to prevent the segregation of dopant to form the SnO2 phase at the hematite crystal surface, reducing its energy and suppressing the grain growth. The increased donor number density provided by the oxygen vacancies (confirmed by x-ray photoelectron data), and a possible reduction in the grain boundary energy or hematite crystal interface might favor charge separation, and increase the electron transfer through the hematite into the back contact (FTO substrate). In consequence, the light-induced water oxidation reaction efficiency of Sn-hematite photoelectrodes was significantly increased in comparison with pure ones, even though the vertical rod morphology was not preserved. This finding provides a novel insight into intentional Sn addition, revealing that dopant segregation at the hematite crystal surface (or at the grain boundaries) could—by increasing the electron mobility—be the more relevant factor in developing active hematite photoelectrodes than the control of columnar morphology.

ITO Modification for Efficient Inverted Organic Solar Cells.

PubMed

Susarova, Diana K; Akkuratov, Alexander V; Kukharenko, Andrey I; Cholakh, Seif O; Kurmaev, Ernst Z; Troshin, Pavel A

2017-10-03

We demonstrate a facile approach to designing transparent electron-collecting electrodes by depositing thin layers of medium and low work function metals on top of transparent conductive metal oxides (TCOs) such as ITO and FTO. The modified electrodes were fairly stable for months under ambient conditions and maintained their electrical characteristics. XPS spectroscopy data strongly suggested integration of the deposited metal in the TCO structure resulting in additional doping of the conducting oxide at the interface. Kelvin probe microscopy measurements revealed a significant decrease in the ITO work function after modification. Organic solar cells based on three different conjugated polymers have demonstrated state of the art performances in inverted device geometry using Mg- or Yb-modified ITO as electron collecting electrode. The simplicity of the proposed approach and the excellent ambient stability of the modified ITO electrodes allows one to expect their wide utilization in research laboratories and electronic industry.

Substrate Structures For Growth Of Highly Oriented And/Or Epitaxial Layers Thereon

DOEpatents

Arendt, Paul N.; Foltyn, Stephen R.; Groves, James R.; Jia, Quanxi

2005-07-26

A composite substrate structure including a substrate, a layer of a crystalline metal oxide or crystalline metal oxynitride material upon the substrate, a layer of an oriented cubic oxide material having a rock-salt-like structure upon the crystalline metal oxide or crystalline metal oxynitride material layer is provided together with additional layers such as one or more layers of a buffer material upon the oriented cubic oxide material layer. Jc's of 2.3×106 A/cm2 have been demonstrated with projected Ic's of 320 Amperes across a sample 1 cm wide for a superconducting article including a flexible polycrystalline metallic substrate, an inert oxide material layer upon the surface of the flexible polycrystalline metallic substrate, a layer of a crystalline metal oxide or crystalline metal oxynitride material upon the layer of the inert oxide material, a layer of an oriented cubic oxide material having a rock-salt-like structure upon the crystalline metal oxide or crystalline metal oxynitride material layer, a layer of a buffer material upon the oriented cubic oxide material layer, and, a top-layer of a high temperature superconducting material upon the layer of a buffer material.

Effect of charged impurities and morphology on oxidation reactivity of graphene

NASA Astrophysics Data System (ADS)

Yamamoto, Mahito; Cullen, William; Einstein, Theodore; Fuhrer, Michael

2012-02-01

Chemical reactivity of single layer graphene supported on a substrate is observed to be enhanced over thicker graphene. Possible mechanisms for the enhancement are Fermi level fluctuations due to ionized impurities on the substrate, and structural deformation of graphene induced by coupling to the substrate geometry. Here, we study the substrate-dependent oxidation reactivity of graphene, employing various substrates such as SiO2, mica, SiO2 nanoparticle thin film, and hexagonal boron nitride, which exhibit different charged impurity concentrations and surface roughness. Graphene is prepared on each substrate via mechanical exfoliation and oxidized in Ar/O2 mixture at temperatures from 400-600 ^oC. After oxidation, the Raman spectrum of graphene is measured, and the Raman D to G peak ratio is used to quantify the density of point defects introduced by oxidation. We will discuss the correlations among the defect density in oxidized graphene, substrate charge inhomogeneity, substrate corrugations, and graphene layer thickness. This work has been supported by the University of Maryland NSF-MRSEC under Grant No. DMR 05-20471 with supplemental funding from NRI, and NSF-DMR 08-04976.

Extension lifetime for dye-sensitized solar cells through multiple dye adsorption/desorption process

NASA Astrophysics Data System (ADS)

Chiang, Yi-Fang; Chen, Ruei-Tang; Shen, Po-Shen; Chen, Peter; Guo, Tzung-Fang

2013-03-01

In this study, we propose a novel concept of extending the lifetime of dye-sensitized solar cells (DSCs) and reducing the costs of re-conditioning DSCs by recycling the FTO/TiO2 substrates. The photovoltaic performances of DSCs using substrates with various cycles of dye uptake and rinse off history are tested. The results show that dye adsorption and Voc are significantly increased under multiple dye adsorption/desorption process and resulted in the improvement of power conversion efficiency. Moreover, the dyeing kinetics is faster after multiple recycling processes, which is favorable for the industrial application. With surface analysis and charge transport characteristics, we also demonstrate the optimal functionality of TiO2/dye interface for the improved Voc and efficiency. The results confirm that the improved performances are due to increased dye loading and dense packing of dye molecules. Our results are beneficial for the understanding on the extension of DSCs lifetime after long-term operation in the application of DSC modules. This approach may also be applied in the replacement of newly synthesized photosensitizes to the active cells.

Physical activity attenuates the effect of the FTO genotype on obesity-related traits in European adults: Findings from the Food4Me study

USDA-ARS?s Scientific Manuscript database

Background. The FTO gene harbours the strongest known susceptibility locus for obesity. Studies of the interaction between genetic and environmental factors such as physical activity (PA) could contribute to the understanding of how lifestyle can modulate genetic susceptibility to obesity. In this s...

Method of making an apparatus for transpiration cooling of substrates such as turbine airfoils

DOEpatents

Alvin, Mary Anne; Anderson, Iver; Heidlof, Andy; White, Emma; McMordie, Bruce

2017-02-28

A method and apparatus for generating transpiration cooling using an oxidized porous HTA layer metallurgically bonded to a substrate having micro-channel architectures. The method and apparatus generates a porous HTA layer by spreading generally spherical HTA powder particles on a substrate, partially sintering under O.sub.2 vacuum until the porous HTA layer exhibits a porosity between 20% and 50% and a neck size ratio between 0.1 and 0.5, followed by a controlled oxidation generating an oxidation layer of alumina, chromia, or silica at a thickness of about 20 to about 500 nm. In particular embodiments, the oxidized porous HTA layer and the substrate comprise Ni as a majority element. In other embodiments, the oxidized porous HTA layer and the substrate further comprise Al, and in additional embodiments, the oxidized porous HTA layer and the substrate comprise .gamma.-Ni+.gamma.'-Ni.sub.3Al.

High resolution masks for ion milling pores through substrates of biological interest

NASA Technical Reports Server (NTRS)

Donovan, S. S.

1978-01-01

The feasibility was investigated of electrochemically oxidizing vapor deposited aluminum coatings to produce porous aluminum oxide coatings with submicron pore diameters and with straight channels normal to the substrate surface. Porous aluminum oxide coatings were produced from vapor deposited aluminum coatings on thin stainless steel (304), copper, Teflon (FEP) and Kapton substrates and also on pure aluminum substrates. Scanning electron microscope examination indicated that porous oxide coatings can be produced with straight channels, appropriate pore diameters and none or minimal intervening residual aluminum. The oxide coatings on the copper and Kapton substrates had the straightest channels and in general were superior to those fabricated on the other substrate materials. For oxide coatings fabricated at 600 V and 300 V, pore diameters were 0.4-0.6, and 0.3 micron with center-to-center spacing of 0.7-0.8, and 0.4 micron, respectively. Estimated direct labor and materials costs to prepare an oxide mask is anticipated to be about $4-$6 per square foot.

Effects of MAR-M247 substrate (modified) composition on coating oxidation coating/substrate interdiffusion. M.S. Thesis. Final Report; [protective coatings for hot section components of gas turbine engines

NASA Technical Reports Server (NTRS)

Pilsner, B. H.

1985-01-01

The effects of gamma+gamma' Mar-M247 substrate composition on gamma+beta Ni-Cr-Al-Zr coating oxidation and coating/substrate interdiffusion were evaluated. These results were also compared to a prior study for a Ni-Cr-Al-Zr coated gamma Ni-Cr-Al substrate with equivalent Al and Cr atomic percentages. Cyclic oxidation behavior at 1130 C was investigated using change in weight curves. Concentration/distance profiles were measured for Al, Cr, Co, W, and Ta. The surface oxides were examined by X-ray diffraction and scanning electron microscopy. The results indicate that variations of Ta and C concentrations in the substrate do not affect oxidation resistance, while additions of grain boundary strengthening elements (Zr, Hf, B) increase oxidation resistance. In addition, the results indicate that oxidation phenomena in gamma+beta/gamma+gamma' Mar-M247 systems have similar characteristics to the l gamma+beta/gamma Ni-Cr-Al system.

Method of applying a cerium diffusion coating to a metallic alloy

DOEpatents

Jablonski, Paul D [Salem, OR; Alman, David E [Benton, OR

2009-06-30

A method of applying a cerium diffusion coating to a preferred nickel base alloy substrate has been discovered. A cerium oxide paste containing a halide activator is applied to the polished substrate and then dried. The workpiece is heated in a non-oxidizing atmosphere to diffuse cerium into the substrate. After cooling, any remaining cerium oxide is removed. The resulting cerium diffusion coating on the nickel base substrate demonstrates improved resistance to oxidation. Cerium coated alloys are particularly useful as components in a solid oxide fuel cell (SOFC).

Method for plating with metal oxides

DOEpatents

Silver, Gary L.; Martin, Frank S.

1994-08-23

A method of plating hydrous metal oxides on at least one substrate, which method is indifferent to the electrochemical properties of the substrate, and comprises reacting metallic ions in aqueous solution with an appropriate oxidizing agent such as sodium hypochlorite or calcium sulfite with oxygen under suitable conditions of pH and concentration such that oxidation and precipitation of metal oxide are sufficiently slow to allow satisfactory plating of metal oxide on the substrate.

Oxidation-Resistant Coating For Bipolar Lead/Acid Battery

NASA Technical Reports Server (NTRS)

Bolstad, James J.

1993-01-01

Cathode side of bipolar substrate coated with nonoxidizable conductive layer. Coating prepared as water slurry of aqueous dispersion of polyethylene copolymer plus such conductive fillers as tin oxide, titanium, tantalum, or tungsten oxide. Applied easily to substrate of polyethylene carbon plastic. As slurry dries, conductive, oxidation-resistant coating forms on positive side of substrate.

Association between FTO gene polymorphisms and type 2 diabetes mellitus, serum levels of apelin and androgen hormones among Iranian obese women.

PubMed

Ghafarian-Alipour, Farzaneh; Ziaee, Shayan; Ashoori, Mohamad Reza; Zakeri, Mir Saeid; Boroumand, Mohammad Ali; Aghamohammadzadeh, Naser; Abbasi-Majdi, Maryam; Shool, Fatemeh; Asbaghi, Navid Sarakhs; Mohammadi, Abolghasem; Zarghami, Nosratollah

2018-01-30

Recent studies show that FTO single nucleotide polymorphisms (SNPs) are associated with obesity and type 2 diabetes mellitus (T2DM). On the other hand, many animal models and clinical studies have demonstrated that apelin, an adipocytokine, is related to the obesity and T2DM. Additionally, obese women are at risk of Hyperandrogenemia. So, the aim of this study was to investigate the relationship between FTO variants (rs763967273, rs759031579, rs141115189, rs9926289, rs76804286 and rs9939609) with T2DM, serum apelin and androgenic hormones in Iranian obese women. 197 obese women (123 women with T2DM and 74 women as healthy control) were participated in this study. Anthropometrical and biochemical characteristics were measured. Serum apelin and androgen hormones levels were determined in 66 subjects consisting of 33 cases and 33 controls. PCR were carried out and subsequently, the PCR production was genotyped by Sanger sequencing assay. Our observations showed that all SNPs are related to T2DM. The rs9926289 FTO variant had a strong association with serum apelin and dehydroepiandrosterone-sulfate levels (P=0.04 and P=0.03, respectively) among SNPs. In addition, apelin and androgenic hormones were correlated with T2DM. Two polymorphisms including rs9939609 and rs9926289 had a strong Linkage disequilibrium (r 2 =1). FTO variants not only were associated with T2DM, but also some variants had a strong association with apelin and androgenic hormones profile. Copyright © 2017 Elsevier B.V. All rights reserved.

Detailed Analysis of Variants in FTO in Association with Body Composition in a Cohort of 70-Year-Olds Suggests a Weakened Effect among Elderly

PubMed Central

Jacobsson, Josefin A.; Almén, Markus Sällman; Benedict, Christian; Hedberg, Lilia A.; Michaëlsson, Karl; Brooks, Samantha; Kullberg, Joel; Axelsson, Tomas; Johansson, Lars; Ahlström, Håkan; Fredriksson, Robert; Lind, Lars; Schiöth, Helgi B.

2011-01-01

Background The rs9939609 single-nucleotide polymorphism (SNP) in the fat mass and obesity (FTO) gene has previously been associated with higher BMI levels in children and young adults. In contrast, this association was not found in elderly men. BMI is a measure of overweight in relation to the individuals' height, but offers no insight into the regional body fat composition or distribution. Objective To examine whether the FTO gene is associated with overweight and body composition-related phenotypes rather than BMI, we measured waist circumference, total fat mass, trunk fat mass, leg fat mass, visceral and subcutaneous adipose tissue, and daily energy intake in 985 humans (493 women) at the age of 70 years. In total, 733 SNPs located in the FTO gene were genotyped in order to examine whether rs9939609 alone or the other SNPs, or their combinations, are linked to obesity-related measures in elderly humans. Design Cross-sectional analysis of the Prospective Investigation of the Vasculature in Uppsala Seniors (PIVUS) cohort. Results Neither a single SNP, such as rs9939609, nor a SNP combination was significantly linked to overweight, body composition-related measures, or daily energy intake in elderly humans. Of note, these observations hold both among men and women. Conclusions Due to the diversity of measurements included in the study, our findings strengthen the view that the effect of FTO on body composition appears to be less profound in later life compared to younger ages and that this is seemingly independent of gender. PMID:21637715

The rs9939609 gene variant in FTO modified the metabolic response of weight loss after a 3-month intervention with a hypocaloric diet.

PubMed

de Luis, Daniel Antonio; Aller, Rocío; Conde, Rosa; Izaola, Olatz; Gonzalez Sagrado, Manuel; Castrodeza Sanz, Javier

2013-01-01

Common polymorphisms in the fat mass and obesity associated gene (FTO) have been linked to obesity in some populations. Nevertheless, the role of FTO variants on body weight response after dietary intervention remains equivocal. We decided to analyze the effects of the rs9939609 FTO gene polymorphism on body weight changes and metabolic parameters after 3 months of a hypocaloric diet. Before and after 3 months on a low-fat hypocaloric diet, a white population of 106 subjects with obesity was analyzed. Of the study subjects, 35 (33%) had the genotype TT and 71 (67%) had the next genotypes; TA (46 study subjects, 43.4%) or AA (25 study subjects, 23.6%). After dietary treatment and in TT group, weight, waist circumference, total cholesterol, LDL-cholesterol, insulin, and homeostasis model assessment decreases were less than subjects carrying the A allele [-3.1 (3.6) vs -2.4 (4.1) kg: P < 0.05], waist circumference [-5.4 (6.4) vs -2.6 (4.8) cm; P < 0.05], total cholesterol [-12.3 (35.3) vs -6.4 (4.7) mg/dL; P < 0.05], LDL-cholesterol [-22.3 (30.5) vs -10.7 (30.5) mg/dL; P < 0.05], insulin [-1.89 (5.5) vs +0.94 (8.2) mUI/L; P < 0.05], and homeostasis model assessment [-0.46 (1.11) vs -0.01 (2.4); P < 0.05]. Our study confirmed a higher weight loss in A carriers of FTO rs9939609 polymorphism than in TT genotype study subjects.

A commonly carried allele of the obesity-related FTO gene is associated with reduced brain volume in the healthy elderly

PubMed Central

Stein, Jason L.; Hua, Xue; Lee, Suh; Hibar, Derrek P.; Leow, Alex D.; Dinov, Ivo D.; Toga, Arthur W.; Saykin, Andrew J.; Shen, Li; Foroud, Tatiana; Pankratz, Nathan; Huentelman, Matthew J.; Craig, David W.; Gerber, Jill D.; Allen, April N.; Corneveaux, Jason J.; Stephan, Dietrich A.; DeCarli, Charles S.; DeChairo, Bryan M.; Potkin, Steven G.; Jack, Clifford R.; Weiner, Michael W.; Raji, Cyrus A.; Lopez, Oscar L.; Becker, James T.; Carmichael, Owen T.; Thompson, Paul M.; Weiner, Michael; Thal, Leon; Petersen, Ronald; Jack, Clifford R.; Jagust, William; Trojanowki, John; Toga, Arthur W.; Beckett, Laurel; Green, Robert C.; Gamst, Anthony; Potter, William Z.; Montine, Tom; Anders, Dale; Bernstein, Matthew; Felmlee, Joel; Fox, Nick; Thompson, Paul; Schuff, Norbert; Alexander, Gene; Bandy, Dan; Koeppe, Robert A.; Foster, Norm; Reiman, Eric M.; Chen, Kewei; Trojanowki, John; Shaw, Les; Lee, Virginia M.-Y.; Korecka, Magdalena; Toga, Arthur W.; Crawford, Karen; Neu, Scott; Harvey, Danielle; Gamst, Anthony; Kornak, John; Kachaturian, Zaven; Frank, Richard; Snyder, Peter J.; Molchan, Susan; Kaye, Jeffrey; Vorobik, Remi; Quinn, Joseph; Schneider, Lon; Pawluczyk, Sonia; Spann, Bryan; Fleisher, Adam S.; Vanderswag, Helen; Heidebrink, Judith L.; Lord, Joanne L.; Johnson, Kris; Doody, Rachelle S.; Villanueva-Meyer, Javier; Chowdhury, Munir; Stern, Yaakov; Honig, Lawrence S.; Bell, Karen L.; Morris, John C.; Mintun, Mark A.; Schneider, Stacy; Marson, Daniel; Griffith, Randall; Badger, Beverly; Grossman, Hillel; Tang, Cheuk; Stern, Jessica; deToledo-Morrell, Leyla; Shah, Raj C.; Bach, Julie; Duara, Ranjan; Isaacson, Richard; Strauman, Silvia; Albert, Marilyn S.; Pedroso, Julia; Toroney, Jaimie; Rusinek, Henry; de Leon, Mony J; De Santi, Susan M; Doraiswamy, P. Murali; Petrella, Jeffrey R.; Aiello, Marilyn; Clark, Christopher M.; Pham, Cassie; Nunez, Jessica; Smith, Charles D.; Given II, Curtis A.; Hardy, Peter; DeKosky, Steven T.; Oakley, MaryAnn; Simpson, Donna M.; Ismail, M. Saleem; Porsteinsson, Anton; McCallum, Colleen; Cramer, Steven C.; Mulnard, Ruth A.; McAdams-Ortiz, Catherine; Diaz-Arrastia, Ramon; Martin-Cook, Kristen; DeVous, Michael; Levey, Allan I.; Lah, James J.; Cellar, Janet S.; Burns, Jeffrey M.; Anderson, Heather S.; Laubinger, Mary M.; Bartzokis, George; Silverman, Daniel H.S.; Lu, Po H.; Fletcher, Rita; Parfitt, Francine; Johnson, Heather; Farlow, Martin; Herring, Scott; Hake, Ann M.; van Dyck, Christopher H.; MacAvoy, Martha G.; Bifano, Laurel A.; Chertkow, Howard; Bergman, Howard; Hosein, Chris; Black, Sandra; Graham, Simon; Caldwell, Curtis; Feldman, Howard; Assaly, Michele; Hsiung, Ging-Yuek R.; Kertesz, Andrew; Rogers, John; Trost, Dick; Bernick, Charles; Gitelman, Darren; Johnson, Nancy; Mesulam, Marsel; Sadowsky, Carl; Villena, Teresa; Mesner, Scott; Aisen, Paul S.; Johnson, Kathleen B.; Behan, Kelly E.; Sperling, Reisa A.; Rentz, Dorene M.; Johnson, Keith A.; Rosen, Allyson; Tinklenberg, Jared; Ashford, Wes; Sabbagh, Marwan; Connor, Donald; Obradov, Sanja; Killiany, Ron; Norbash, Alex; Obisesan, Thomas O.; Jayam-Trouth, Annapurni; Wang, Paul; Auchus, Alexander P.; Huang, Juebin; Friedland, Robert P.; DeCarli, Charles; Fletcher, Evan; Carmichael, Owen; Kittur, Smita; Mirje, Seema; Johnson, Sterling C.; Borrie, Michael; Lee, T-Y; Asthana, Sanjay; Carlsson, Cynthia M.; Potkin, Steven G.; Highum, Diane; Preda, Adrian; Nguyen, Dana; Tariot, Pierre N.; Hendin, Barry A.; Scharre, Douglas W.; Kataki, Maria; Beversdorf, David Q.; Zimmerman, Earl A.; Celmins, Dzintra; Brown, Alice D.; Gandy, Sam; Marenberg, Marjorie E.; Rovner, Barry W.; Pearlson, Godfrey; Blank, Karen; Anderson, Karen; Saykin, Andrew J.; Santulli, Robert B.; Pare, Nadia; Williamson, Jeff D.; Sink, Kaycee M.; Potter, Huntington; Ashok Raj, B.; Giordano, Amy; Ott, Brian R.; Wu, Chuang-Kuo; Cohen, Ronald; Wilks, Kerri L.

2010-01-01

A recently identified variant within the fat mass and obesity-associated (FTO) gene is carried by 46% of Western Europeans and is associated with an ~1.2 kg higher weight, on average, in adults and an ~1 cm greater waist circumference. With >1 billion overweight and 300 million obese persons worldwide, it is crucial to understand the implications of carrying this very common allele for the health of our aging population. FTO is highly expressed in the brain and elevated body mass index (BMI) is associated with brain atrophy, but it is unknown how the obesity-associated risk allele affects human brain structure. We therefore generated 3D maps of regional brain volume differences in 206 healthy elderly subjects scanned with MRI and genotyped as part of the Alzheimer's Disease Neuroimaging Initiative. We found a pattern of systematic brain volume deficits in carriers of the obesity-associated risk allele versus noncarriers. Relative to structure volumes in the mean template, FTO risk allele carriers versus noncarriers had an average brain volume difference of ~8% in the frontal lobes and 12% in the occipital lobes—these regions also showed significant volume deficits in subjects with higher BMI. These brain differences were not attributable to differences in cholesterol levels, hypertension, or the volume of white matter hyperintensities; which were not detectably higher in FTO risk allele carriers versus noncarriers. These brain maps reveal that a commonly carried susceptibility allele for obesity is associated with structural brain atrophy, with implications for the health of the elderly. PMID:20404173

A commonly carried allele of the obesity-related FTO gene is associated with reduced brain volume in the healthy elderly.

PubMed

Ho, April J; Stein, Jason L; Hua, Xue; Lee, Suh; Hibar, Derrek P; Leow, Alex D; Dinov, Ivo D; Toga, Arthur W; Saykin, Andrew J; Shen, Li; Foroud, Tatiana; Pankratz, Nathan; Huentelman, Matthew J; Craig, David W; Gerber, Jill D; Allen, April N; Corneveaux, Jason J; Stephan, Dietrich A; DeCarli, Charles S; DeChairo, Bryan M; Potkin, Steven G; Jack, Clifford R; Weiner, Michael W; Raji, Cyrus A; Lopez, Oscar L; Becker, James T; Carmichael, Owen T; Thompson, Paul M

2010-05-04

A recently identified variant within the fat mass and obesity-associated (FTO) gene is carried by 46% of Western Europeans and is associated with an approximately 1.2 kg higher weight, on average, in adults and an approximately 1 cm greater waist circumference. With >1 billion overweight and 300 million obese persons worldwide, it is crucial to understand the implications of carrying this very common allele for the health of our aging population. FTO is highly expressed in the brain and elevated body mass index (BMI) is associated with brain atrophy, but it is unknown how the obesity-associated risk allele affects human brain structure. We therefore generated 3D maps of regional brain volume differences in 206 healthy elderly subjects scanned with MRI and genotyped as part of the Alzheimer's Disease Neuroimaging Initiative. We found a pattern of systematic brain volume deficits in carriers of the obesity-associated risk allele versus noncarriers. Relative to structure volumes in the mean template, FTO risk allele carriers versus noncarriers had an average brain volume difference of approximately 8% in the frontal lobes and 12% in the occipital lobes-these regions also showed significant volume deficits in subjects with higher BMI. These brain differences were not attributable to differences in cholesterol levels, hypertension, or the volume of white matter hyperintensities; which were not detectably higher in FTO risk allele carriers versus noncarriers. These brain maps reveal that a commonly carried susceptibility allele for obesity is associated with structural brain atrophy, with implications for the health of the elderly.

Screening method for selecting semiconductor substrates having defects below a predetermined level in an oxide layer

DOEpatents

Warren, W.L.; Vanheusden, K.J.R.; Schwank, J.R.; Fleetwood, D.M.; Shaneyfelt, M.R.; Winokur, P.S.; Devine, R.A.B.

1998-07-28

A method is disclosed for screening or qualifying semiconductor substrates for integrated circuit fabrication. The method comprises the steps of annealing at least one semiconductor substrate at a first temperature in a defect-activating ambient (e.g. hydrogen, forming gas, or ammonia) for sufficient time for activating any defects within on oxide layer of the substrate; measuring a defect-revealing electrical characteristic of at least a portion of the oxide layer for determining a quantity of activated defects therein; and selecting substrates for which the quantity of activated defects is below a predetermined level. The defect-revealing electrical characteristic may be a capacitance-versus voltage (C-V) characteristic or a current-versus-voltage (I-V) characteristic that is dependent on an electrical charge in the oxide layer generated by the activated defects. Embodiments of the present invention may be applied for screening any type of semiconductor substrate or wafer having an oxide layer formed thereon or therein. This includes silicon-on-insulator substrates formed by a separation by the implantation of oxygen (SIMOX) process or the bond and etch back silicon-on-insulator (BESOI) process, as well as silicon substrates having a thermal oxide layer or a deposited oxide layer. 5 figs.

Method for plating with metal oxides

DOEpatents

Silver, G.L.; Martin, F.S.

1994-08-23

A method is disclosed of plating hydrous metal oxides on at least one substrate, which method is indifferent to the electrochemical properties of the substrate, and comprises reacting metallic ions in aqueous solution with an appropriate oxidizing agent such as sodium hypochlorite or calcium sulfite with oxygen under suitable conditions of pH and concentration such that oxidation and precipitation of metal oxide are sufficiently slow to allow satisfactory plating of metal oxide on the substrate. 1 fig.

Do Reactions of Adaptation to Disability Influence the Fluctuation of Future Time Orientation among Individuals with Spinal Cord Injuries?

ERIC Educational Resources Information Center

Martz, Erin

2004-01-01

Rehabilitation counseling involves the construction of vocational goals, which involves future-oriented thinking. Yet, research indicates that time orientations may change after the experience of a trauma. Due to the potential importance of a future time orientation (FTO) in rehabilitation counseling, predictors of an FTO were examined among 317…

Heterostructured ZnFe2O4/Fe2TiO5/TiO2 Composite Nanotube Arrays with an Improved Photocatalysis Degradation Efficiency Under Simulated Sunlight Irradiation

NASA Astrophysics Data System (ADS)

Xiong, Kun; Wang, Kunzhou; Chen, Lin; Wang, Xinqing; Fan, Qingbo; Courtois, Jérémie; Liu, Yuliang; Tuo, Xianguo; Yan, Minhao

2018-03-01

To improve the visible light absorption and photocatalytic activity of titanium dioxide nanotube arrays (TONTAs), ZnFe2O4 (ZFO) nanocrystals were perfused into pristine TONTA pipelines using a novel bias voltage-assisted perfusion method. ZFO nanocrystals were well anchored on the inner walls of the pristine TONTAs when the ZFO suspensions (0.025 mg mL-1) were kept under a 60 V bias voltage for 1 h. After annealing at 750 °C for 2 h, the heterostructured ZFO/Fe2TiO5 (FTO)/TiO2 composite nanotube arrays were successfully obtained. Furthermore, Fe3+ was reduced to Fe2+ when solid solution reactions occurred at the interface of ZFO and the pristine TONTAs. Introducing ZFO significantly enhanced the visible light absorption of the ZFO/FTO/TONTAs relative to that of the annealed TONTAs. The coexistence of type I and staggered type II band alignment in the ZFO/FTO/TONTAs facilitated the separation of photogenerated electrons and holes, thereby improving the efficiency of the ZFO/FTO/TONTAs for photocatalytic degradation of methylene blue when irradiated with simulated sunlight. [Figure not available: see fulltext.

Associations of FTO and MC4R Variants with Obesity Traits in Indians and the Role of Rural/Urban Environment as a Possible Effect Modifier

PubMed Central

Taylor, A. E.; Sandeep, M. N.; Janipalli, C. S.; Giambartolomei, C.; Evans, D. M.; Kranthi Kumar, M. V.; Vinay, D. G.; Smitha, P.; Gupta, V.; Aruna, M.; Kinra, S.; Sullivan, R. M.; Bowen, L.; Timpson, N. J.; Davey Smith, G.; Dudbridge, F.; Prabhakaran, D.; Ben-Shlomo, Y.; Reddy, K. S.; Ebrahim, S.; Chandak, G. R.

2011-01-01

Few studies have investigated the association between genetic variation and obesity traits in Indian populations or the role of environmental factors as modifiers of these relationships. In the context of rapid urbanisation, resulting in significant lifestyle changes, understanding the aetiology of obesity is important. We investigated associations of FTO and MC4R variants with obesity traits in 3390 sibling pairs from four Indian cities, most of whom were discordant for current dwelling (rural or urban). The FTO variant rs9939609 predicted increased weight (0.09 Z-scores, 95% CI: 0.03, 0.15) and BMI (0.08 Z-scores, 95% CI: 0.02, 0.14). The MC4R variant rs17782313 was weakly associated with weight and hip circumference (P < .05). There was some indication that the association between FTO and weight was stronger in urban than that in rural dwellers (P for interaction = .03), but no evidence for effect modification by diet or physical activity. Further studies are needed to investigate ways in which urban environment may modify genetic risk of obesity. PMID:21785715

Associations of FTO and MC4R Variants with Obesity Traits in Indians and the Role of Rural/Urban Environment as a Possible Effect Modifier.

PubMed

Taylor, A E; Sandeep, M N; Janipalli, C S; Giambartolomei, C; Evans, D M; Kranthi Kumar, M V; Vinay, D G; Smitha, P; Gupta, V; Aruna, M; Kinra, S; Sullivan, R M; Bowen, L; Timpson, N J; Davey Smith, G; Dudbridge, F; Prabhakaran, D; Ben-Shlomo, Y; Reddy, K S; Ebrahim, S; Chandak, G R

2011-01-01

Few studies have investigated the association between genetic variation and obesity traits in Indian populations or the role of environmental factors as modifiers of these relationships. In the context of rapid urbanisation, resulting in significant lifestyle changes, understanding the aetiology of obesity is important. We investigated associations of FTO and MC4R variants with obesity traits in 3390 sibling pairs from four Indian cities, most of whom were discordant for current dwelling (rural or urban). The FTO variant rs9939609 predicted increased weight (0.09 Z-scores, 95% CI: 0.03, 0.15) and BMI (0.08 Z-scores, 95% CI: 0.02, 0.14). The MC4R variant rs17782313 was weakly associated with weight and hip circumference (P < .05). There was some indication that the association between FTO and weight was stronger in urban than that in rural dwellers (P for interaction = .03), but no evidence for effect modification by diet or physical activity. Further studies are needed to investigate ways in which urban environment may modify genetic risk of obesity.

Annealing effect of fluorine-doped SnO2/WO3 core-shell inverse opal nanoarchitecture for photoelectrochemical water splitting

NASA Astrophysics Data System (ADS)

Cho, Seo Yoon; Kang, Soon Hyung; Yun, Gun; Balamurugan, Maheswari; Ahn, Kwang-Soon

2017-01-01

Fluorine-doped SnO2 inverse opal (FTO IO) was developed on a polystyrene bead template with a size of 350 nm (± 20 nm) by using the sol-gel-assisted spin-coating method. The resulting FTO IO film exhibited a pore diameter of 270 nm (± 5 nm), and a WO3 layer was electrodeposited with a constant charge of 400 mC/cm2, followed by a high-temperature annealing process (400, 475, and 550 °C) to increase the crystallinity of the IO films. The annealing temperature affected the morphology and the overall resistance of the thin film, thus significantly affecting the photoelectrochemical performance. In particular, the FTO/WO3 IO film annealed at 475 °C exhibited a photocurrent density of 2.9 mA/cm2 at 1.23 V versus normal hydrogen electrode, showing more than a three times higher photocurrent density in comparison with the other samples (550 °C), which is attributed to the large surface area and low resistance for the charge transport. Therefore, the annealing temperature significantly affects the morphological and the photoelectrochemical features of the FTO/WO3 IO films.

Regulation of Substrate Oxidation Preferences in Muscle by the Peptide Hormone Adropin

PubMed Central

Gao, Su; McMillan, Ryan P.; Jacas, Jordi; Zhu, Qingzhang; Li, Xuesen; Kumar, Ganesh K.; Casals, Núria; Hegardt, Fausto G.; Robbins, Paul D.; Lopaschuk, Gary D.; Hulver, Matthew W.

2014-01-01

Rigorous control of substrate oxidation by humoral factors is essential for maintaining metabolic homeostasis. During feeding and fasting cycles, carbohydrates and fatty acids are the two primary substrates in oxidative metabolism. Here, we report a novel role for the peptide hormone adropin in regulating substrate oxidation preferences. Plasma levels of adropin increase with feeding and decrease upon fasting. A comparison of whole-body substrate preference and skeletal muscle substrate oxidation in adropin knockout and transgenic mice suggests adropin promotes carbohydrate oxidation over fat oxidation. In muscle, adropin activates pyruvate dehydrogenase (PDH), which is rate limiting for glucose oxidation and suppresses carnitine palmitoyltransferase-1B (CPT-1B), a key enzyme in fatty acid oxidation. Adropin downregulates PDH kinase-4 (PDK4) that inhibits PDH, thereby increasing PDH activity. The molecular mechanisms of adropin’s effects involve acetylation (suggesting inhibition) of the transcriptional coactivator PGC-1α, downregulating expression of Cpt1b and Pdk4. Increased PGC-1α acetylation by adropin may be mediated by inhibiting Sirtuin-1 (SIRT1), a PGC-1α deacetylase. Altered SIRT1 and PGC-1α activity appear to mediate aspects of adropin’s metabolic actions in muscle. Similar outcomes were observed in fasted mice treated with synthetic adropin. Together, these results suggest a role for adropin in regulating muscle substrate preference under various nutritional states. PMID:24848071

High-Performance Platinum-Free Dye-Sensitized Solar Cells with Molybdenum Disulfide Films as Counter Electrodes.

PubMed

Hussain, Sajjad; Shaikh, Shoyebmohamad F; Vikraman, Dhanasekaran; Mane, Rajaram S; Joo, Oh-Shim; Naushad, Mu; Jung, Jongwan

2015-12-21

By using a radio-frequency sputtering method, we synthesized large-area, uniform, and transparent molybdenum disulfide film electrodes (1, 3, 5, and 7 min) on transparent and conducting fluorine-doped tin oxide (FTO), as ecofriendly, cost-effective counter electrodes (CE) for dye-sensitized solar cells (DSSCs). These CEs were used in place of the routinely used expensive platinum CEs for the catalytic reduction of a triiodide electrolyte. The structure and morphology of the MoS2 was analyzed by using Raman spectroscopy, X-ray diffraction, and X-ray photoemission spectroscopy measurements and the DSSC characteristics were investigated. An unbroken film of MoS2 was identified on the FTO crystallites from field-emission scanning electron microscopy. Cyclic voltammetry, electrochemical impedance spectroscopy, and Tafel curve measurements reveal the promise of MoS2 as a CE with a low charge-transfer resistance, high electrocatalytic activity, and fast reaction kinetics for the reduction of triiodide to iodide. Finally, an optimized transparent MoS2 CE, obtained after 5 min synthesis time, showed a high power-conversion efficiency of 6.0 %, which comparable to the performance obtained with a Pt CE (6.6 %) when used in TiO2 -based DSCCs, thus signifying the importance of sputtering time on DSSC performance. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Artificial Photosynthesis of Alcohols by Multi-Functionalized Semiconductor Photocathodes.

PubMed

Zhang, Yuqian; Han, Bo; Xu, Yanjie; Zhao, Dongning; Jia, Yongjian; Nie, Rong; Zhu, Zhouhe; Chen, Fengjuan; Wang, Jianguo; Jing, Huanwang

2017-04-22

Novel artificial photosynthesis systems are devised as cells of dye/Pd/NR-MO x (M=Ti, Zn)∥CoPi/W:BiVO 4 that convert efficiently CO 2 to alcohols. The photocathodes are aminofunctionalized, palladium-deposited, and in situ sensitized nano-TiO 2 or ZnO/FTO (FTO: fluorine-doped tin oxide) electrodes that are characterized by X-ray photoelectron spectroscopy (XPS), TEM, XRD, UV/Vis spectra, and evaluated by electrochemical techniques. The cell of dye/Pd/S-TiO 2 ∥CoPi/W:BiVO 4 uniquely generates ethanol under irradiation of 200 mW cm -2 , reaching 0.56 % quantum efficiency (QE) at -0.56 V and 0.13 % QE without external electron supply. The cell of dye/Pd/ N-ZnO∥CoPi/W:BiVO 4 produces solely methanol at a rate of 42.8 μm h -1  cm -2 at -0.56 V of a Si solar cell, which is far less than the electrochemical voltage of water splitting (1.23 V). Its QE reaches to 0.38 %, which is equal to plants. The isotopic labeling experiments confirm the carbon source and oxygen releasing. The selectivity for alcohols of multi-functionalized semiconductors is discussed. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Dye-sensitized solar cell characteristics of nanocomposite zinc ferrite working electrode: effect of composite precursors and titania as a blocking layer on photovoltaic performance.

PubMed

Habibi, Mohammad Hossein; Habibi, Amir Hossein; Zendehdel, Mahmoud; Habibi, Mehdi

2013-06-01

This research investigates the performance of a zinc ferrite (ZF) as working electrodes in a dye-sensitized solar cell (DSSC). This ZF working electrode was prepared by sol-gel and thermal decomposition of four different precursors including: zinc acetate dihydrate (Zn(CH3COO)2·2H2O), ferric nitrate nonahydrate (Fe(NO3)3·9H2O), iron(III) acetate; Fe(C2H3O2)3, and zinc nitrate hexahydrate, Zn(NO3)2·6H2O. The effects of annealing temperature and precursors on the structural, morphological, and optical properties were investigated. The field emission scanning electron microscope images (FESEM) and scanning electron microscopy (SEM) show that ZFe films are polycrystalline in nature and homogeneous with densely packed grains. Nanoporous zinc ferrite coatings were prepared by doctor blade technique on the fluorine-doped tin oxide (FTO) and used as working electrodes in DSSC. In all DSSCs, platinized FTO and [Co(bpy)3](2+/3+) in 3-methoxy proponitrile were used as counter electrode and redox mediator system respectively. Comparing the fill factors of four different zinc ferrite nanocomposites, the highest fill factor was for ZnFe2O4-TBL sample. Cell fabricated with ZnFeA working electrode shows relatively higher Jsc. Copyright © 2013 Elsevier B.V. All rights reserved.

Electrocatalyst for alcohol oxidation in fuel cells

DOEpatents

Adzic, Radoslav R.; Marinkovic, Nebojsa S.

2001-01-01

Binary and ternary electrocatalysts are provided for oxidizing alcohol in a fuel cell. The binary electrocatalyst includes 1) a substrate selected from the group consisting of NiWO.sub.4 or CoWO.sub.4 or a combination thereof, and 2) Group VIII noble metal catalyst supported on the substrate. The ternary electrocatalyst includes 1) a substrate as described above, and 2) a catalyst comprising Group VIII noble metal, and ruthenium oxide or molybdenum oxide or a combination thereof, said catalyst being supported on said substrate.

Spinel-structured metal oxide on a substrate and method of making same by molecular beam epitaxy

DOEpatents

Chambers, Scott A.

2006-02-21

A method of making a spinel-structured metal oxide on a substrate by molecular beam epitaxy, comprising the step of supplying activated oxygen, a first metal atom flux, and at least one other metal atom flux to the surface of the substrate, wherein the metal atom fluxes are individually controlled at the substrate so as to grow the spinel-structured metal oxide on the substrate and the metal oxide is substantially in a thermodynamically stable state during the growth of the metal oxide. A particular embodiment of the present invention encompasses a method of making a spinel-structured binary ferrite, including Co ferrite, without the need of a post-growth anneal to obtain the desired equilibrium state.

Superconducting composite with multilayer patterns and multiple buffer layers

DOEpatents

Wu, X.D.; Muenchausen, R.E.

1993-10-12

An article of manufacture is described including a substrate, a patterned interlayer of a material selected from the group consisting of magnesium oxide, barium-titanium oxide or barium-zirconium oxide, the patterned interlayer material overcoated with a secondary interlayer material of yttria-stabilized zirconia or magnesium-aluminum oxide, upon the surface of the substrate whereby an intermediate article with an exposed surface of both the overcoated patterned interlayer and the substrate is formed, a coating of a buffer layer selected from the group consisting of cerium oxide, yttrium oxide, curium oxide, dysprosium oxide, erbium oxide, europium oxide, iron oxide, gadolinium oxide, holmium oxide, indium oxide, lanthanum oxide, manganese oxide, lutetium oxide, neodymium oxide, praseodymium oxide, plutonium oxide, samarium oxide, terbium oxide, thallium oxide, thulium oxide, yttrium oxide and ytterbium oxide over the entire exposed surface of the intermediate article, and, a ceramic superconductor. 5 figures.

[Effect of sodium and calcium ions on glutamate and glutamine oxidation by rat brain synaptosomes].

PubMed

Nilova, N S

1978-08-01

5 mM oxidative substrates and 0.15 mM Ca(2+) being used, different effects of Ca(2+) on the oxidation are possible, such as an additional inhibition of glutamine oxidation and an additional activation of glutamate oxidation. A decreased Na+-ion concentration in the medium inhibited synaptosomal respiration with glutamate as a substrate. With glutamine as a substrate oxygen consumption does not change.

Polycrystalline ferroelectric or multiferroic oxide articles on biaxially textured substrates and methods for making same

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goyal, Amit; Shin, Junsoo

A polycrystalline ferroelectric and/or multiferroic oxide article includes a substrate having a biaxially textured surface; at least one biaxially textured buffer layer supported by the substrate; and a biaxially textured ferroelectric or multiferroic oxide layer supported by the buffer layer. Methods for making polycrystalline ferroelectric and/or multiferroic oxide articles are also disclosed.

An enhanced mangiferaindica for dye sensitized solar cell application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Uno, U. E., E-mail: moses.emetere@covenantuniversity.edu.ng; Emetere, M. E., E-mail: uno-essang@yahoo.co.uk; Fadipe, L. A.

Titanium dioxide (T1O2) is preferred to Zinc oxide as mesoporous oxide layer because it raised the efficiency of DSSCs from 1% to 7%. The chemistry of the process however seem rigorous to allow the light induced electron injection from the adsorbed dye into the nanocrystallites i.e. which renders the TiO{sub 2} conductive. The DSSC fabricated consist of 2.25 cm{sup 2} active area of titanium dioxide coated on FTO glass (fluorine tin oxide) immersed in ethanol solution of natural dye extracted as an anode (electrode) and counter electrode. These two electrodes were coupled together and the space between them was filledmore » with the Iodolyte AN-50 as solid electrolyte or redox mediator. The photo electrochemical parameters of the dye extracted (Mango fruit Peel) from the results obtained are short circuit current (Isc)= 1.22×10{sup −2}, current density (Jsc)=4.07×10{sup −2}, open circuit voltage (voc) =0.53V, fill factor (FF) of 0.16 and the overall conversion efficiency (Eff) =0.345%.« less

Superconductive articles including cerium oxide layer

DOEpatents

Wu, X.D.; Muenchausen, R.E.

1993-11-16

A ceramic superconductor comprising a metal oxide substrate, a ceramic high temperature superconductive material, and a intermediate layer of a material having a cubic crystal structure, said layer situated between the substrate and the superconductive material is provided, and a structure for supporting a ceramic superconducting material is provided, said structure comprising a metal oxide substrate, and a layer situated over the surface of the substrate to substantially inhibit interdiffusion between the substrate and a ceramic superconducting material deposited upon said structure. 7 figures.

Superconductive articles including cerium oxide layer

DOEpatents

Wu, Xin D.; Muenchausen, Ross E.

1993-01-01

A ceramic superconductor comprising a metal oxide substrate, a ceramic high temperature superconductive material, and a intermediate layer of a material having a cubic crystal structure, said layer situated between the substrate and the superconductive material is provided, and a structure for supporting a ceramic superconducting material is provided, said structure comprising a metal oxide substrate, and a layer situated over the surface of the substrate to substantially inhibit interdiffusion between the substrate and a ceramic superconducting material deposited upon said structure.

The Substance of Things Hoped for: A Study of the Future Orientation, Minority Status Perceptions, Academic Engagement, and Academic Performance of Black High School Students

ERIC Educational Resources Information Center

Brown, William T.; Jones, James M.

2004-01-01

This study investigated the relationship between the Future Temporal Orientation (FTO) and academic performance of African American high school students. We hypothesized that the relationship between FTO and academic performance would be mediated by students' perceptions of the usefulness of an education and their valuing of academic work and that…

Can genetic-based advice help you lose weight? Findings from the Food4Me European randomized controlled trial.

PubMed

Celis-Morales, Carlos; Marsaux, Cyril Fm; Livingstone, Katherine M; Navas-Carretero, Santiago; San-Cristobal, Rodrigo; Fallaize, Rosalind; Macready, Anna L; O'Donovan, Clare; Woolhead, Clara; Forster, Hannah; Kolossa, Silvia; Daniel, Hannelore; Moschonis, George; Mavrogianni, Christina; Manios, Yannis; Surwillo, Agnieszka; Traczyk, Iwona; Drevon, Christian A; Grimaldi, Keith; Bouwman, Jildau; Gibney, Mike J; Walsh, Marianne C; Gibney, Eileen R; Brennan, Lorraine; Lovegrove, Julie A; Martinez, J Alfredo; Saris, Wim Hm; Mathers, John C

2017-05-01

Background: There has been limited evidence about whether genotype-tailored advice provides extra benefits in reducing obesity-related traits compared with the benefits of conventional one-size-fits-all advice. Objective: We determined whether the disclosure of information on fat-mass and obesity-associated ( FTO ) genotype risk had a greater effect on a reduction of obesity-related traits in risk carriers than in nonrisk carriers across different levels of personalized nutrition. Design: A total of 683 participants (women: 51%; age range: 18-73 y) from the Food4Me randomized controlled trial were included in this analysis. Participants were randomly assigned to 4 intervention arms as follows: level 0, control group; level 1, dietary group; level 2, phenotype group; and level 3, genetic group. FTO (single nucleotide polymorphism rs9939609) was genotyped at baseline in all participants, but only subjects who were randomly assigned to level 3 were informed about their genotypes. Level 3 participants were stratified into risk carriers (AA/AT) and nonrisk carriers (TT) of the FTO gene for analyses. Height, weight, and waist circumference (WC) were self-measured and reported at baseline and months 3 and 6. Results: Changes in adiposity markers were greater in participants who were informed that they carried the FTO risk allele (level 3 AT/AA carriers) than in the nonpersonalized group (level 0) but not in the other personalized groups (level 1 and 2). Mean reductions in weight and WC at month 6 were greater for FTO risk carriers than for noncarriers in the level 3 group [-2.28 kg (95% CI: -3.06, -1.48 kg) compared with -1.99 kg (-2.19, -0.19 kg), respectively ( P = 0.037); and -4.34 cm (-5.63, -3.08 cm) compared with -1.99 cm (-4.04, -0.05 cm), respectively, ( P = 0.048)]. Conclusions: There are greater body weight and WC reductions in risk carriers than in nonrisk carriers of the FTO gene. This trial was registered at clinicaltrials.gov as NCT01530139. © 2017 American Society for Nutrition.

Gender-Dependent Association of FTO Polymorphisms with Body Mass Index in Mexicans

PubMed Central

Saldaña-Alvarez, Yolanda; Salas-Martínez, María Guadalupe; García-Ortiz, Humberto; Luckie-Duque, Angélica; García-Cárdenas, Gustavo; Vicenteño-Ayala, Hermenegildo; Cordova, Emilio J.; Esparza-Aguilar, Marcelino; Contreras-Cubas, Cecilia; Carnevale, Alessandra; Chávez-Saldaña, Margarita; Orozco, Lorena

2016-01-01

To evaluate the associations between six single-nucleotide polymorphisms (SNPs) in intron 1 of FTO and body mass index (BMI), a case-control association study of 2314 unrelated Mexican-Mestizo adult subjects was performed. The association between each SNP and BMI was tested using logistic and linear regression adjusted for age, gender, and ancestry and assuming additive, recessive, and dominant effects of the minor allele. Association analysis after BMI stratification showed that all five FTO SNPs (rs1121980, rs17817449, rs3751812, rs9930506, and rs17817449), were significantly associated with obesity class II/III under an additive model (P<0.05). Interestingly, we also documented a genetic model-dependent influence of gender on the effect of FTO variants on increased BMI. Two SNPs were specifically associated in males under a dominant model, while the remainder were associated with females under additive and recessive models (P<0.05). The SNP rs9930506 showed the highest increased in obesity risk in females (odds ratio = 4.4). Linear regression using BMI as a continuous trait also revealed differential FTO SNP contributions. Homozygous individuals for the risk alleles of rs17817449, rs3751812, and rs9930506 were on average 2.18 kg/m2 heavier than homozygous for the wild-type alleles; rs1121980 and rs8044769 showed significant but less-strong effects on BMI (1.54 kg/m2 and 0.9 kg/m2, respectively). Remarkably, rs9930506 also exhibited positive interactions with age and BMI in a gender-dependent manner. Women carrying the minor allele of this variant have a significant increase in BMI by year (0.42 kg/m2, P = 1.17 x 10−10). Linear regression haplotype analysis under an additive model, confirmed that the TGTGC haplotype harboring all five minor alleles, increased the BMI of carriers by 2.36 kg/m2 (P = 1.15 x 10−5). Our data suggest that FTO SNPs make differential contributions to obesity risk and support the hypothesis that gender differences in the mechanisms involving these variants may contribute to disease development. PMID:26726774

Physical Activity Attenuates the Influence of FTO Variants on Obesity Risk: A Meta-Analysis of 218,166 Adults and 19,268 Children

PubMed Central

Kilpeläinen, Tuomas O.; Qi, Lu; Brage, Soren; Sharp, Stephen J.; Sonestedt, Emily; Demerath, Ellen; Ahmad, Tariq; Mora, Samia; Kaakinen, Marika; Sandholt, Camilla Helene; Holzapfel, Christina; Autenrieth, Christine S.; Hyppönen, Elina; Cauchi, Stéphane; He, Meian; Kutalik, Zoltan; Kumari, Meena; Stančáková, Alena; Meidtner, Karina; Balkau, Beverley; Tan, Jonathan T.; Mangino, Massimo; Timpson, Nicholas J.; Song, Yiqing; Zillikens, M. Carola; Jablonski, Kathleen A.; Garcia, Melissa E.; Johansson, Stefan; Bragg-Gresham, Jennifer L.; Wu, Ying; van Vliet-Ostaptchouk, Jana V.; Onland-Moret, N. Charlotte; Zimmermann, Esther; Rivera, Natalia V.; Tanaka, Toshiko; Stringham, Heather M.; Silbernagel, Günther; Kanoni, Stavroula; Feitosa, Mary F.; Snitker, Soren; Ruiz, Jonatan R.; Metter, Jeffery; Larrad, Maria Teresa Martinez; Atalay, Mustafa; Hakanen, Maarit; Amin, Najaf; Cavalcanti-Proença, Christine; Grøntved, Anders; Hallmans, Göran; Jansson, John-Olov; Kuusisto, Johanna; Kähönen, Mika; Lutsey, Pamela L.; Nolan, John J.; Palla, Luigi; Pedersen, Oluf; Pérusse, Louis; Renström, Frida; Scott, Robert A.; Shungin, Dmitry; Sovio, Ulla; Tammelin, Tuija H.; Rönnemaa, Tapani; Lakka, Timo A.; Uusitupa, Matti; Rios, Manuel Serrano; Ferrucci, Luigi; Bouchard, Claude; Meirhaeghe, Aline; Fu, Mao; Walker, Mark; Borecki, Ingrid B.; Dedoussis, George V.; Fritsche, Andreas; Ohlsson, Claes; Boehnke, Michael; Bandinelli, Stefania; van Duijn, Cornelia M.; Ebrahim, Shah; Lawlor, Debbie A.; Gudnason, Vilmundur; Harris, Tamara B.; Sørensen, Thorkild I. A.; Mohlke, Karen L.; Hofman, Albert; Uitterlinden, André G.; Tuomilehto, Jaakko; Lehtimäki, Terho; Raitakari, Olli; Isomaa, Bo; Njølstad, Pål R.; Florez, Jose C.; Liu, Simin; Ness, Andy; Spector, Timothy D.; Tai, E. Shyong; Froguel, Philippe; Boeing, Heiner; Laakso, Markku; Marmot, Michael; Bergmann, Sven; Power, Chris; Khaw, Kay-Tee; Chasman, Daniel; Ridker, Paul; Hansen, Torben; Monda, Keri L.; Illig, Thomas; Järvelin, Marjo-Riitta; Wareham, Nicholas J.; Hu, Frank B.; Groop, Leif C.; Orho-Melander, Marju; Ekelund, Ulf; Franks, Paul W.; Loos, Ruth J. F.

2011-01-01

Background The FTO gene harbors the strongest known susceptibility locus for obesity. While many individual studies have suggested that physical activity (PA) may attenuate the effect of FTO on obesity risk, other studies have not been able to confirm this interaction. To confirm or refute unambiguously whether PA attenuates the association of FTO with obesity risk, we meta-analyzed data from 45 studies of adults (n = 218,166) and nine studies of children and adolescents (n = 19,268). Methods and Findings All studies identified to have data on the FTO rs9939609 variant (or any proxy [r 2>0.8]) and PA were invited to participate, regardless of ethnicity or age of the participants. PA was standardized by categorizing it into a dichotomous variable (physically inactive versus active) in each study. Overall, 25% of adults and 13% of children were categorized as inactive. Interaction analyses were performed within each study by including the FTO×PA interaction term in an additive model, adjusting for age and sex. Subsequently, random effects meta-analysis was used to pool the interaction terms. In adults, the minor (A−) allele of rs9939609 increased the odds of obesity by 1.23-fold/allele (95% CI 1.20–1.26), but PA attenuated this effect (p interaction  = 0.001). More specifically, the minor allele of rs9939609 increased the odds of obesity less in the physically active group (odds ratio  = 1.22/allele, 95% CI 1.19–1.25) than in the inactive group (odds ratio  = 1.30/allele, 95% CI 1.24–1.36). No such interaction was found in children and adolescents. Conclusions The association of the FTO risk allele with the odds of obesity is attenuated by 27% in physically active adults, highlighting the importance of PA in particular in those genetically predisposed to obesity. Please see later in the article for the Editors' Summary PMID:22069379

Photovoltaic and Impedance Spectroscopy Study of Screen-Printed TiO₂ Based CdS Quantum Dot Sensitized Solar Cells.

PubMed

Atif, M; Farooq, W A; Fatehmulla, Amanullah; Aslam, M; Ali, Syed Mansoor

2015-01-19

Cadmium sulphide (CdS) quantum dot sensitized solar cells (QDSSCs) based on screen-printed TiO₂ were assembled using a screen-printing technique. The CdS quantum dots (QDs) were grown by using the Successive Ionic Layer Adsorption and Reaction (SILAR) method. The optical properties were studied by UV-Vis absorbance spectroscopy. Photovoltaic characteristics and impedance spectroscopic measurements of CdS QDSSCs were carried out under air mass 1.5 illuminations. The experimental results of capacitance against voltage indicate a trend from positive to negative capacitance because of the injection of electrons from the Fluorine doped tin oxide (FTO) electrode into TiO₂.

Elemental Metals or Oxides Distributed on a Carbon Substrate or Self-Supported and the Manufacturing Process Using Graphite Oxide as Template

NASA Technical Reports Server (NTRS)

Hung, Ching-Chen (Inventor)

1999-01-01

A process for providing elemental metals or metal oxides distributed on a carbon substrate or self-supported utilizing graphite oxide as a percursor. The graphite oxide is exposed to one or more metal chlorides to form an intermediary product comprising carbon, metal, chloride, and oxygen. This intermediary product can be further processed by direct exposure to carbonate solutions to form a second intermediary product comprising carbon, metal carbonate, and oxygen. Either intermediary product may be further processed: a) in air to produce metal oxide; b) in an inert environment to produce metal oxide on carbon substrate; c) in a reducing environment to produce elemental metal distributed on carbon substrate. The product generally takes the shape of the carbon precursor.

Elemental Metals or Oxides Distributed on a Carbon Substrate or Self-Supported and the Manufacturing Process Using Graphite Oxide as Template

NASA Technical Reports Server (NTRS)

Hung, Ching-Cheh (Inventor)

1999-01-01

A process for providing elemental metals or metal oxides distributed on a carbon substrate or self-supported utilizing graphite oxide as a precursor. The graphite oxide is exposed to one or more metal chlorides to form an intermediary product comprising carbon, metal, chloride, and oxygen. This intermediary product can be further processed by direct exposure to carbonate-solutions to form a second intermediary product comprising carbon, metal carbonate, and oxygen. Either intermediary product may be further processed: a) in air to produce metal oxide; b) in an inert environment to produce metal oxide on carbon substrate; c) in a reducing environment to produce elemental metal distributed on carbon substrate. The product generally takes the shape of the carbon precursor.

Ammonia release method for depositing metal oxides

DOEpatents

Silver, Gary L.; Martin, Frank S.

1994-12-13

A method of depositing metal oxides on substrates which is indifferent to the electrochemical properties of the substrates and which comprises forming ammine complexes containing metal ions and thereafter effecting removal of ammonia from the ammine complexes so as to permit slow precipitation and deposition of metal oxide on the substrates.

Improving the efficiency of quantum-dot-sensitized solar cells by optimizing the growth time of the CuS counter electrode

NASA Astrophysics Data System (ADS)

Sunesh, Chozhidakath Damodharan; Gopi, Chandu V. V. M.; Muthalif, Mohammed Panthakkal Abdul; Kim, Hee-Je; Choe, Youngson

2017-09-01

CuS counter electrodes (CEs) were prepared to fabricate efficient quantum-dot-sensitized solar cells (QDSSCs) based on a CdS/CdSe photo sensitizer. The CEs were prepared on a fluorine-doped tin oxide (FTO) glass substrate by a facile chemical bath deposition (CBD) method by dissolving CuSO4·5H2O and CH3CSNH2 in water, followed by adding 0.25 mM polyvinylpyrrolidone (PVP). The CBD was performed at 60 °C for 1 h, 2 h, and 3 h, and the samples were labeled as CuS 1 h, CuS 2 h, and CuS 3 h, respectively. The QDSSCs were assembled using prepared CuS CEs and a TiO2/CdS/CdSe/ZnS photoanode, and the effect of the growth time of CuS CEs on the QDSSC performance was investigated. As the CuS growth time increases, the short-circuit current density (Jsc), fill factor (FF), and open-circuit voltage (Voc) of the QDSSCs gradually increases, leading to an enhanced power conversion efficiency (η). QDSSCs that use the CuS 2 h CE exhibit a high Jsc of 14.31 mA cm-2, Voc of 0.603 V, and FF of 0.49, which are higher than that using conventional Pt electrodes as well as CuS 1 h and CuS 3 h electrodes. The electrochemical impedance spectroscopy results show that the CuS 2 h CE exhibits an inferior charge transfer resistance of only 2.93 Ω, which is 33 times lesser than that of the Pt CE. The enhanced device performance of CuS 2 h is ascribed to the high catalytic activity and low charge transfer resistance of the CuS CE in the reduction process of oxidized polysulfide. Consequently, a superior power conversion efficiency of 4.27% is achieved for QDSSCs utilizing CuS 2 h.

Substrate inhibition: Oxidation of D-sorbitol and D-mannitol by potassium periodate in alkaline medium

NASA Astrophysics Data System (ADS)

Lakshman Kumar, Y.; Venkata Nadh, R.; Radhakrishnamurti, P. S.

2014-05-01

In the oxidation of D-sorbitol and D-mannitol by potassium periodate in alkaline media, substrate inhibition was observed with both substrates, i.e., a decrease in the rate of the reaction was observed with an increase in the concentration of substrate. The substrate inhibition was attributed to the formation of stable complex between the substrate and periodate. The reactions were found to be first order in case of periodate and a positive fractional order with hydroxide ions. Arrhenius parameters were calculated for the oxidation of sorbitol and mannitol by potassium periodate in alkali media.

A common variant near BDNF is associated with dietary calcium intake in adolescents.

PubMed

Dušátková, Lenka; Zamrazilová, Hana; Aldhoon-Hainerová, Irena; Sedláčková, Barbora; Včelák, Josef; Hlavatý, Petr; Bendlová, Běla; Kunešová, Marie; Hainer, Vojtěch

2015-09-01

Specific targets for most obesity candidate genes discovered by genomewide association studies remain unknown. Such genes are often highly expressed in the hypothalamus, indicating their role in energy homeostasis. We aimed to evaluate the associations of selected gene variants with adiposity and dietary traits. Anthropometric parameters, fat mass, dietary intake (total energy, fat, protein, carbohydrate, fiber, and calcium) and 10 gene variants (in/near TMEM18, SH2B1, KCTD15, PCSK1, BDNF, SEC16B, MC4R and FTO) were analyzed in 1953 Czech individuals aged 10.0 to 18.0 years (1035 nonoverweight and 918 overweight: body mass index [BMI] ≥90th percentile). Obesity risk alleles of TMEM18 rs7561317, SEC16B rs10913469, and FTO rs9939609 were related to increased body weight and BMI (P < .005). The FTO variant also showed a significant positive association with waist circumference and fat mass (P < .001). Overweight adolescents had a lower total energy intake (P < .001) but a higher percentage of fat (P = .009) and protein intake (P < .001) than the nonoverweight subjects. There was also a lower calcium intake in the overweight group (P < .001). An association with at least one component of dietary intake was found in 3 of 10 studied gene variants. The MC4R rs17782313 was associated negatively with protein (P = .012) and positively associated with fiber (P = .032) intakes. The obesity risk alleles of BDNF rs925946 and FTO rs9939609 were related to a lower calcium intake (P = .001 and .037). The effects of FTO and MC4R variants, however, disappeared after corrections for multiple testing. Our results suggest that the common BDNF variant may influence dietary calcium intake independent of BMI. Copyright © 2015 Elsevier Inc. All rights reserved.

Relationships between FTO rs9939609, MC4R rs17782313, and PPARγ rs1801282 polymorphisms and the occurrence of selected metabolic and hormonal disorders in middle-aged and elderly men - a preliminary study.

PubMed

Rotter, Iwona; Skonieczna-Żydecka, Karolina; Kosik-Bogacka, Danuta; Adler, Grażyna; Rył, Aleksandra; Laszczyńska, Maria

2016-01-01

Metabolic disorders, including MetS, obesity, and lipid disorders, may be related to genetic factors. Metabolic disorders are associated with decreased TS levels in aging men. The aim of this study was to evaluate the relationship between FTO rs9939609, MC4R rs17782313, and PPARγ rs1801282 polymorphisms and the presence of MetS and its components, the concurrent lipid disorders, as well as sex hormone concentrations. This study involved 272 men of Caucasian descent aged 50-75 years. Lipid profile, including TCh, LDL, HDL, and TG, was evaluated by spectrophotometric method. Anthropometric measurements concerned WC and blood pressure. MetS was diagnosed according to the criteria of the IDF. Sex hormone profile, including TST, FTS, E 2 , DHEAS, and SHBG, was examined using enzyme-linked immunosorbent assay. Polymorphisms within FTO , MC4R , and PPARγ genes were identified using polymerase chain reaction-restriction fragments length polymorphism. This study did not show links between the analyzed genetic polymorphisms and the presence of MetS, T2DM, HT, and obesity. However, higher concentrations of TCh and LDL were found in men with the FTO rs9939609 polymorphism in the recessive mode of inheritance ( P =0.03 and P =0.05, respectively). Lower WC was found to be associated with MC4R rs17782313 gene inherited in the same model ( P =0.005). FTO rs9939609, MC4R rs17782313, and PPARγ rs1801282 polymorphisms seem to have little effect on the incidence of metabolic malfunctions and no effect on androgen-related disorders in the examined middle-aged and elderly men.

Excessive fuel availability amplifies the FTO-mediated obesity risk: results from the TUEF and Whitehall II studies.

PubMed

Wagner, Róbert; Tabák, Ádám G; Fehlert, Ellen; Fritsche, Louise; Jaghutriz, Benjamin A; Bánhegyi, Róbert J; Schmid, Sebastian M; Staiger, Harald; Machicao, Fausto; Peter, Andreas; Häring, Hans-Ulrich; Fritsche, Andreas; Heni, Martin

2017-11-14

Variation in FTO is the most important common genetic determinant of body weight. Altered energy metabolism could underlie this association. We hypothesized that higher circulating glucose or triglycerides can amplify the FTO impact on BMI. In 2671 subjects of the TUEF study, we investigated the interaction effect of fasting glucose and triglyceride levels with rs9939609 in FTO on BMI. We analysed the same interaction effect by longitudinally utilizing mixed effect models in the prospective Whitehall II study. In TUEF, we detected an interaction effect between fasting glucose and fasting triglycerides with rs9939609 on BMI (p = 0.0005 and p = 5 × 10 -7 , respectively). The effect size of one risk allele was 1.4 ± 0.3 vs. 2.2 ± 0.44 kg/m² in persons with fasting glucose levels below and above the median, respectively. Fasting triglycerides above the median increased the per-allele effect from 1.4 ± 0.3 to 1.7 ± 0.4 kg/m 2 . In the Whitehall II study, body weight increased by 2.96 ± 6.5 kg during a follow-up of 13.5 ± 4.6 yrs. Baseline fasting glucose and rs9939609 interacted on weight change (p = 0.009). Higher fasting glucose levels may amplify obesity-risk in FTO carriers and lead to an exaggerated weight gain over time. Since weight gain perpetuates metabolic alterations, this interplay may trigger a vicious circle that leads to obesity and diabetes.

FTO gene variants are strongly associated with type 2 diabetes in South Asian Indians.

PubMed

Yajnik, C S; Janipalli, C S; Bhaskar, S; Kulkarni, S R; Freathy, R M; Prakash, S; Mani, K R; Weedon, M N; Kale, S D; Deshpande, J; Krishnaveni, G V; Veena, S R; Fall, C H D; McCarthy, M I; Frayling, T M; Hattersley, A T; Chandak, G R

2009-02-01

Variants of the FTO (fat mass and obesity associated) gene are associated with obesity and type 2 diabetes in white Europeans, but these associations are not consistent in Asians. A recent study in Asian Indian Sikhs showed an association with type 2 diabetes that did not seem to be mediated through BMI. We studied the association of FTO variants with type 2 diabetes and measures of obesity in South Asian Indians in Pune. We genotyped, by sequencing, two single nucleotide polymorphisms, rs9939609 and rs7191344, in the FTO gene in 1,453 type 2 diabetes patients and 1,361 controls from Pune, Western India and a further 961 population-based individuals from Mysore, South India. We observed a strong association of the minor allele A at rs9939609 with type 2 diabetes (OR per allele 1.26; 95% CI 1.13-1.40; p = 3 x 10(-5)). The variant was also associated with BMI but this association appeared to be weaker (0.06 SDs; 95% CI 0.01-0.10) than the previously reported effect in Europeans (0.10 SDs; 95% CI 0.09-0.12; heterogeneity p = 0.06). Unlike in the Europeans, the association with type 2 diabetes remained significant after adjusting for BMI (OR per allele for type 2 diabetes 1.21; 95% CI 1.06-1.37; p = 4.0 x 10(-3)), and also for waist circumference and other anthropometric variables. Our study replicates the strong association of FTO variants with type 2 diabetes and similar to the study in North Indians Sikhs, shows that this association may not be entirely mediated through BMI. This could imply underlying differences between Indians and Europeans in the mechanisms linking body size with type 2 diabetes.

Is the adiposity-associated FTO gene variant related to all-cause mortality independent of adiposity? Meta-analysis of data from 169,551 Caucasian adults

PubMed Central

Mirza, S. S.; Zhao, J. H.; Chasman, D. I.; Fischer, K.; Qi, Q.; Smith, A. V.; Thinggaard, M.; Jarczok, M. N.; Nalls, M. A.; Trompet, S.; Timpson, N. J.; Schmidt, B.; Jackson, A. U.; Lyytikäinen, L. P.; Verweij, N.; Mueller-Nurasyid, M.; Vikström, M.; Marques-Vidal, P.; Wong, A.; Meidtner, K.; Middelberg, R. P.; Strawbridge, R. J.; Christiansen, L.; Kyvik, K. O.; Hamsten, A.; Jääskeläinen, T.; Tjønneland, A.; Eriksson, J. G.; Whitfield, J. B.; Boeing, H.; Hardy, R.; Vollenweider, P.; Leander, K.; Peters, A.; van der Harst, P.; Kumari, M.; Lehtimäki, T.; Meirhaeghe, A.; Tuomilehto, J.; Jöckel, K.-H.; Ben-Shlomo, Y.; Sattar, N.; Baumeister, S. E.; Smith, G. Davey; Casas, J. P.; Houston, D. K.; März, W.; Christensen, K.; Gudnason, V.; Hu, F. B.; Metspalu, A.; Ridker, P. M.; Wareham, N. J.; Loos, R. J. F.; Tiemeier, H.; Sonestedt, E.; Sørensen, T. I. A.

2015-01-01

Summary Previously, a single nucleotide polymorphism (SNP), rs9939609, in the FTO gene showed a much stronger association with all-cause mortality than expected from its association with body mass index (BMI), body fat mass index (FMI) and waist circumference (WC). This finding implies that the SNP has strong pleiotropic effects on adiposity and adiposity-independent pathological pathways that leads to increased mortality. To investigate this further, we conducted a meta-analysis of similar data from 34 longitudinal studies including 169,551 adult Caucasians among whom 27,100 died during follow-up. Linear regression showed that the minor allele of the FTO SNP was associated with greater BMI (n = 169,551; 0.32 kg m−2; 95% CI 0.28–0.32, P < 1 × 10−32), WC (n = 152,631; 0.76 cm; 0.68–0.84, P < 1 × 10−32) and FMI (n = 48,192; 0.17 kg m−2; 0.13–0.22, P = 1.0 × 10−13). Cox proportional hazard regression analyses for mortality showed that the hazards ratio (HR) for the minor allele of the FTO SNPs was 1.02 (1.00–1.04, P = 0.097), but the apparent excess risk was eliminated after adjustment for BMI and WC (HR: 1.00; 0.98–1.03, P = 0.662) and for FMI (HR: 1.00; 0.96–1.04, P = 0.932). In conclusion, this study does not support that the FTO SNP is associated with all-cause mortality independently of the adiposity phenotypes. PMID:25752329

Association of the FTO and ADRB2 genes with body composition and fat distribution in obese women.

PubMed

Rauhio, Anne; Uusi-Rasi, Kirsti; Nikkari, Seppo T; Kannus, Pekka; Sievänen, Harri; Kunnas, Tarja

2013-10-01

The aim of this study was to investigate whether the polymorphisms of the fat mass and obesity-associated gene (FTO, rs9939609:T>A) and the β2-adrenergic receptor gene (ADRB2, rs1042714:Gln>Glu) are associated with weight loss in dieting obese premenopausal women and the association of these SNPs with body weight, body composition and distribution of fat mass. 75 obese (BMI>30) premenopausal women participated in the intervention including a 3-month weight reduction period and a subsequent 9-month weight maintenance period. Weight and height were measured and BMI calculated. Body composition and fat mass distribution were assessed by dual energy X-ray absorptiometry. At baseline, the AA homozygotes of the FTO gene were 10.1 kg heavier (p=0.031), they had higher BMI (p=0.038), and greater waist and greater hip circumference (p=0.08 and p=0.067, respectively) compared to the TT homozygotes. Gln/Gln carriers of the ADRB2 gene had smaller gynoid fat-% compared with both the Gln/Glu and Glu/Glu carriers (p=0.050 and p=0.009, respectively). The Gln homozygotes had also smaller total body fat-% and higher total body lean mass-% than that of the Glu homozygotes (p=0.018 and p=0.019, respectively). FTO genotype was associated with body weight in general, whereas ADRB2 genotype was associated with fat distribution. However, all women in the study group lost weight similarly independently of their genotypes. Neither the FTO nor ADRB2 genotype had statistically significant effect on weight reduction or weight maintenance. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Aerosol chemical vapor deposition of metal oxide films

DOEpatents

Ott, K.C.; Kodas, T.T.

1994-01-11

A process of preparing a film of a multicomponent metal oxide including: forming an aerosol from a solution comprised of a suitable solvent and at least two precursor compounds capable of volatilizing at temperatures lower than the decomposition temperature of said precursor compounds; passing said aerosol in combination with a suitable oxygen-containing carrier gas into a heated zone, said heated zone having a temperature sufficient to evaporate the solvent and volatilize said precursor compounds; and passing said volatilized precursor compounds against the surface of a substrate, said substrate having a sufficient temperature to decompose said volatilized precursor compounds whereby metal atoms contained within said volatilized precursor compounds are deposited as a metal oxide film upon the substrate is disclosed. In addition, a coated article comprising a multicomponent metal oxide film conforming to the surface of a substrate selected from the group consisting of silicon, magnesium oxide, yttrium-stabilized zirconium oxide, sapphire, or lanthanum gallate, said multicomponent metal oxide film characterized as having a substantially uniform thickness upon said substrate.

Process for depositing epitaxial alkaline earth oxide onto a substrate and structures prepared with the process

DOEpatents

McKee, Rodney A.; Walker, Frederick J.

1996-01-01

A process and structure involving a silicon substrate utilize molecular beam epitaxy (MBE) and/or electron beam evaporation methods and an ultra-high vacuum facility to grow a layup of epitaxial alkaline earth oxide films upon the substrate surface. By selecting metal constituents for the oxides and in the appropriate proportions so that the lattice parameter of each oxide grown closely approximates that of the substrate or base layer upon which oxide is grown, lattice strain at the film/film or film/substrate interface of adjacent films is appreciably reduced or relieved. Moreover, by selecting constituents for the oxides so that the lattice parameters of the materials of adjacent oxide films either increase or decrease in size from one parameter to another parameter, a graded layup of films can be grown (with reduced strain levels therebetween) so that the outer film has a lattice parameter which closely approximates that of, and thus accomodates the epitaxial growth of, a pervoskite chosen to be grown upon the outer film.

Analysis of factors affecting the accuracy, reproducibility, and interpretation of microbial community carbon source utilization patterns

USGS Publications Warehouse

Haack, S.K.; Garchow, H.; Klug, M.J.; Forney, L.J.

1995-01-01

We determined factors that affect responses of bacterial isolates and model bacterial communities to the 95 carbon substrates in Biolog microliter plates. For isolates and communities of three to six bacterial strains, substrate oxidation rates were typically nonlinear and were delayed by dilution of the inoculum. When inoculum density was controlled, patterns of positive and negative responses exhibited by microbial communities to each of the carbon sources were reproducible. Rates and extents of substrate oxidation by the communities were also reproducible but were not simply the sum of those exhibited by community members when tested separately. Replicates of the same model community clustered when analyzed by principal- components analysis (PCA), and model communities with different compositions were clearly separated un the first PCA axis, which accounted for >60% of the dataset variation. PCA discrimination among different model communities depended on the extent to which specific substrates were oxidized. However, the substrates interpreted by PCA to be most significant in distinguishing the communities changed with reading time, reflecting the nonlinearity of substrate oxidation rates. Although whole-community substrate utilization profiles were reproducible signatures for a given community, the extent of oxidation of specific substrates and the numbers or activities of microorganisms using those substrates in a given community were not correlated. Replicate soil samples varied significantly in the rate and extent of oxidation of seven tested substrates, suggesting microscale heterogeneity in composition of the soil microbial community.

Substrate specificity and copper loading of the manganese-oxidizing multicopper oxidase Mnx from Bacillus sp. PL-12.

PubMed

Butterfield, Cristina N; Tebo, Bradley M

2017-02-22

Manganese(ii) oxidation in the environment is thought to be driven by bacteria because enzymatic catalysis is many orders of magnitude faster than the abiotic processes. The heterologously purified Mn oxidase (Mnx) from marine Bacillus sp. PL-12 is made up of the multicopper oxidase (MCO) MnxG and two small Cu and heme-binding proteins of unknown function, MnxE and MnxF. Mnx binds Cu and oxidizes both Mn(ii) and Mn(iii), generating Mn(iv) oxide minerals that resemble those found on the Bacillus spore surface. Spectroscopic techniques have illuminated details about the metallo-cofactors of Mnx, but very little is known about their requirement for catalytic activity, and even less is known about the substrate specificity of Mnx. Here we quantify the canonical MCO Cu and persistent peripheral Cu bound to Mnx, and test Mnx oxidizing ability toward different substrates at varying pH. Mn(ii) appears to be the best substrate in terms of k cat , but its oxidation does not follow Michaelis-Menten kinetics, instead showing a sigmoidal cooperative behavior. Mnx also oxidizes Fe(ii) substrate, but in a Michaelis-Menten manner and with a decreased activity, as well as organic substrates. The reduced metals are more rapidly consumed than the larger organic substrates, suggesting the hypothesis that the Mnx substrate site is small and tuned for metal oxidation. Of biological relevance is the result that Mnx has the highest catalytic efficiency for Mn(ii) at the pH of sea water, especially when the protein is loaded with greater than the requisite four MCO copper atoms, suggesting that the protein has evolved specifically for Mn oxidation.

Lack of association between genetic polymorphism of FTO, AKT1 and AKTIP in childhood overweight and obesity.

PubMed

Pereira, Patrícia de Araújo; Alvim-Soares, António Marcos; Sandrim, Valéria Cristina; Lanna, Carla Márcia Moreira; Souza-Costa, Débora Cristine; Belo, Vanessa de Almeida; de Paula, Jonas Jardim; Tanus-Santos, José Eduardo; Romano-Silva, Marco Aurélio; Miranda, Débora Marques de

2016-01-01

Obesity is a chronic disease caused by both environmental and genetic factors. Epidemiological studies have documented that increased energy intake and sedentary lifestyle, as well as a genetic contribution, are forces behind the obesity epidemic. Knowledge about the interaction between genetic and environmental components can facilitate the choice of the most effective and specific measures for the prevention of obesity. The aim of this study was to assess the association between the FTO, AKT1, and AKTIP genes and childhood obesity and insulin resistance. This was a case-control study in which SNPs in the FTO (rs99396096), AKT1, and AKTIP genes were genotyped in groups of controls and obese/overweight children. The study included 195 obese/overweight children and 153 control subjects. As expected, the obese/overweight group subjects had higher body mass index, higher fasting glucose, HOMA-IR index, total cholesterol, low-density lipoprotein, and triglycerides. However, no significant differences were observed in genes polymorphisms genotype or allele frequencies. The present results suggest that AKT1, FTO, and AKTIP polymorphisms were not associated with obesity/overweight in Brazilians children. Future studies on the genetics of obesity in Brazilian children and their environment interactions are needed. Copyright © 2016 Sociedade Brasileira de Pediatria. Published by Elsevier Editora Ltda. All rights reserved.

Ammonia release method for depositing metal oxides

DOEpatents

Silver, G.L.; Martin, F.S.

1994-12-13

A method is described for depositing metal oxides on substrates which is indifferent to the electrochemical properties of the substrates and which comprises forming ammine complexes containing metal ions and thereafter effecting removal of ammonia from the ammine complexes so as to permit slow precipitation and deposition of metal oxide on the substrates. 1 figure.

Method for preparing high temperature superconductor

DOEpatents

Balachandran, Uthamalingam; Chudzik, Michael P.

2002-01-01

A method of depositing a biaxially textured metal oxide on a substrate defining a plane in which metal oxide atoms are vaporized from a source to form a plume of metal oxide atoms. Atoms in the plume disposed at a selected angle in a predetermined range of angles to the plane of the substrate are allowed to contact the substrate while preventing atoms outside a selected angle from reaching the substrate. The preferred range of angles is 40.degree.-70.degree. and the preferred angle is 60.degree..+-.5.degree.. A moving substrate is disclosed.

Influence of TiCl4 precursor in hydrothermal synthesis of TiO2 nanostructures

NASA Astrophysics Data System (ADS)

Kartikay, Purnendu; Nemala, Siva Sankar; Mallick, Sudhanshu

2017-05-01

Rutile TiO2 films were deposited on the FTO substrate by the hydrothermal process using TTIP and TiCl4 as the titania precursor. Our study manifestly exhibits the influence of TiCl4 precursor on the hydrothermal growth of the TiO2 structure. The morphology of prepared film varies from nano-cauliflower to nano-flower to nano-parallelepiped rod-like structure with the addition of TiCl4 as the precursor. When TiCl4 is introduced in the precursor HCl corresponding to four times of the Ti4+ concentration is generated as a by-product during the reaction, these additional HCl promotes the etching of the nanostructure enabling the nanostructure to unfurl. We conclude that the tailoring of the nanostructure can be performed by addition of TiCl4 in the precursor

Controllable synthesis of ZnxCd1-xS@ZnO core-shell nanorods with enhanced photocatalytic activity.

PubMed

Xie, Shilei; Lu, Xihong; Zhai, Teng; Gan, Jiayong; Li, Wei; Xu, Ming; Yu, Minghao; Zhang, Yuan-Ming; Tong, Yexiang

2012-07-17

We report the synthesis of Zn(x)Cd(1-x)S@ZnO nanorod arrays via a facile two-step process and the implementation of these core-shell nanorods as an environmental friendly and recyclable photocatalyst for methyl orange degradation. The band gap of Zn(x)Cd(1-x)S@ZnO core-shell nanorods can be readily tunable by adjusting the ratio of Zn/Cd during the synthesis. These Zn(x)Cd(1-x)S@ZnO core-shell nanorods exhibit a high photocatalytic activity and good stability in the degradation of the methyl orange. Moreover, these films grown on FTO substrates make the collection and recycle of the photocatalyst easier. These findings may open new opportunities for the design of effective, stable, and easy-recyclable photocatalytic materials.

Electrospinning Titanium Dioxide (TiO2) nanofiber for dye sensitized solar cells based on Bryophyta as a sensitizer

NASA Astrophysics Data System (ADS)

Asma Ilahi, Novita; Suryana, Risa; Nurrosyid, Fahru; Kusuma, N. T. Linda

2017-01-01

From an engineering and economic perspective, immobilized TiO2 nanocatalysts are preferred in a variety of applications. In this study, TiO2 polymer solution was synthesized using ethanol, acetic acid, polyvinylpyrrolidone (PVP), and titanium tetra isopropoxide (TTIP). TiO2 solution was deposited on the FTO substrate by electrospinning method to obtain nano-sized layer. Capillary of syringes given a positive DC voltage of 6 kV to produce nanofiber, then annealed at 450 °C for 3 hours. Chlorophyll has obtained from extracted moss through a chromatographic process to used for dye. TiO2 nanofiber layer manufactured with varied by time and characterized by UV-Vis and IV-meter. The result exhibited a maximum efficiency of 0,0036% and significant absorption at 350 nm-500 nm wavelength.

Redox-dependent substrate-cofactor interactions in the Michaelis-complex of a flavin-dependent oxidoreductase

NASA Astrophysics Data System (ADS)

Werther, Tobias; Wahlefeld, Stefan; Salewski, Johannes; Kuhlmann, Uwe; Zebger, Ingo; Hildebrandt, Peter; Dobbek, Holger

2017-07-01

How an enzyme activates its substrate for turnover is fundamental for catalysis but incompletely understood on a structural level. With redox enzymes one typically analyses structures of enzyme-substrate complexes in the unreactive oxidation state of the cofactor, assuming that the interaction between enzyme and substrate is independent of the cofactors oxidation state. Here, we investigate the Michaelis complex of the flavoenzyme xenobiotic reductase A with the reactive reduced cofactor bound to its substrates by X-ray crystallography and resonance Raman spectroscopy and compare it to the non-reactive oxidized Michaelis complex mimics. We find that substrates bind in different orientations to the oxidized and reduced flavin, in both cases flattening its structure. But only authentic Michaelis complexes display an unexpected rich vibrational band pattern uncovering a strong donor-acceptor complex between reduced flavin and substrate. This interaction likely activates the catalytic ground state of the reduced flavin, accelerating the reaction within a compressed cofactor-substrate complex.

Redox-dependent substrate-cofactor interactions in the Michaelis-complex of a flavin-dependent oxidoreductase

PubMed Central

Werther, Tobias; Wahlefeld, Stefan; Salewski, Johannes; Kuhlmann, Uwe; Zebger, Ingo; Hildebrandt, Peter; Dobbek, Holger

2017-01-01

How an enzyme activates its substrate for turnover is fundamental for catalysis but incompletely understood on a structural level. With redox enzymes one typically analyses structures of enzyme–substrate complexes in the unreactive oxidation state of the cofactor, assuming that the interaction between enzyme and substrate is independent of the cofactors oxidation state. Here, we investigate the Michaelis complex of the flavoenzyme xenobiotic reductase A with the reactive reduced cofactor bound to its substrates by X-ray crystallography and resonance Raman spectroscopy and compare it to the non-reactive oxidized Michaelis complex mimics. We find that substrates bind in different orientations to the oxidized and reduced flavin, in both cases flattening its structure. But only authentic Michaelis complexes display an unexpected rich vibrational band pattern uncovering a strong donor–acceptor complex between reduced flavin and substrate. This interaction likely activates the catalytic ground state of the reduced flavin, accelerating the reaction within a compressed cofactor–substrate complex.

Nitrification in a zeoponic substrate

NASA Technical Reports Server (NTRS)

McGilloway, R. L.; Weaver, R. W.; Ming, D. W.; Gruener, J. E.

2003-01-01

Clinoptilolite is a zeolite mineral with high cation exchange capacity used in zeoponic substrates that have been proposed as a solid medium for growing plants or as a fertilizer material. The kinetics of nitrification has not been measured for NH4+ saturated zeoponic substrate. Experiments were conducted to evaluate the production of NO2- and NO3-, and nitrifier populations in zeoponic substrates. Small columns were filled with zeoponic substrate inoculated with a commercial inoculum or soil enrichment culture of nitrifying bacteria. In addition to column studies, a growth chamber study was conducted to evaluate the kinetics of nitrification in zeoponic substrates used to grow radishes (Raphanus sativus L.). The zeoponic substrate provided a readily available source of NH4+, and nitrifying bacteria were active in the substrate. Ammonium oxidation rates in column studies ranged from 5 to 10 micrograms N g-1 substrate h-1, and NO2- oxidation rates were 2 to 9.5 micrograms N g-1 substrate h-1. Rates determined from the growth chamber study were approximately 1.2 micrograms N g-1 substrate h-1. Quantities of NH4+ oxidized to NO2- and NO3- in inoculated zeoponic substrate were in excess of plant up-take. Acidification as a result of NH4+ oxidation resulted in a pH decline, and the zeoponic substrate showed limited buffering capacity.

Facile, substrate-scale growth of mono- and few-layer homogeneous MoS2 films on Mo foils with enhanced catalytic activity as counter electrodes in DSSCs.

PubMed

Antonelou, Aspasia; Syrrokostas, George; Sygellou, Lamprini; Leftheriotis, George; Dracopoulos, Vassileios; Yannopoulos, Spyros N

2016-01-29

The growth of MoS2 films by sulfurization of Mo foils at atmospheric pressure is reported. The growth procedure provides, in a controlled way, mono- and few-layer thick MoS2 films with substrate-scale uniformity across square-centimeter area on commercial foils without any pre- or post-treatment. The prepared few-layer MoS2 films are investigated as counter electrodes for dye-sensitized solar cells (DSSCs) by assessing their ability to catalyse the reduction of I3(-) to I(-) in triiodide redox shuttles. The dependence of the MoS2 catalytic activity on the number of monolayers is explored down to the bilayer thickness, showing performance similar to that of, and stability against corrosion better than, Pt-based nanostructured film. The DSSC with the MoS2-Mo counter electrode yields a photovoltaic energy conversion efficiency of 8.4%, very close to that of the Pt-FTO-based DSSC, i.e. 8.7%. The current results disclose a facile, cost-effective and green method for the fabrication of mechanically robust and chemically stable, few-layer MoS2 on flexible Mo substrates and further demonstrate that efficient counter electrodes for DSSCs can be prepared at thicknesses down to the 1-2 nm scale.

Determination of interfacial adhesion strength between oxide scale and substrate for metallic SOFC interconnects

NASA Astrophysics Data System (ADS)

Sun, X.; Liu, W. N.; Stephens, E.; Khaleel, M. A.

The interfacial adhesion strength between the oxide scale and the substrate is crucial to the reliability and durability of metallic interconnects in solid oxide fuel cell (SOFC) operating environments. It is necessary, therefore, to establish a methodology to quantify the interfacial adhesion strength between the oxide scale and the metallic interconnect substrate, and furthermore to design and optimize the interconnect material as well as the coating materials to meet the design life of an SOFC system. In this paper, we present an integrated experimental/analytical methodology for quantifying the interfacial adhesion strength between the oxide scale and a ferritic stainless steel interconnect. Stair-stepping indentation tests are used in conjunction with subsequent finite element analyses to predict the interfacial strength between the oxide scale and Crofer 22 APU substrate.

Methods of repairing a substrate

NASA Technical Reports Server (NTRS)

Riedell, James A. (Inventor); Easler, Timothy E. (Inventor)

2011-01-01

A precursor of a ceramic adhesive suitable for use in a vacuum, thermal, and microgravity environment. The precursor of the ceramic adhesive includes a silicon-based, preceramic polymer and at least one ceramic powder selected from the group consisting of aluminum oxide, aluminum nitride, boron carbide, boron oxide, boron nitride, hafnium boride, hafnium carbide, hafnium oxide, lithium aluminate, molybdenum silicide, niobium carbide, niobium nitride, silicon boride, silicon carbide, silicon oxide, silicon nitride, tin oxide, tantalum boride, tantalum carbide, tantalum oxide, tantalum nitride, titanium boride, titanium carbide, titanium oxide, titanium nitride, yttrium oxide, zirconium boride, zirconium carbide, zirconium oxide, and zirconium silicate. Methods of forming the ceramic adhesive and of repairing a substrate in a vacuum and microgravity environment are also disclosed, as is a substrate repaired with the ceramic adhesive.

Oxidation resistant high temperature thermal cycling resistant coatings on silicon-based substrates and process for the production thereof

DOEpatents

Sarin, V.K.

1990-08-21

An oxidation resistant, high temperature thermal cycling resistant coated ceramic article for ceramic heat engine applications is disclosed. The substrate is a silicon-based material, i.e. a silicon nitride- or silicon carbide-based monolithic or composite material. The coating is a graded coating of at least two layers: an intermediate AlN or Al[sub x]N[sub y]O[sub z] layer and an aluminum oxide or zirconium oxide outer layer. The composition of the coating changes gradually from that of the substrate to that of the AlN or Al[sub x]N[sub y]O[sub z] layer and further to the composition of the aluminum oxide or zirconium oxide outer layer. Other layers may be deposited over the aluminum oxide layer. A CVD process for depositing the graded coating on the substrate is also disclosed.

Oxidation resistant high temperature thermal cycling resistant coatings on silicon-based substrates and process for the production thereof

DOEpatents

Sarin, Vinod K.

1990-01-01

An oxidation resistant, high temperature thermal cycling resistant coated ceramic article for ceramic heat engine applications. The substrate is a silicon-based material, i.e. a silicon nitride- or silicon carbide-based monolithic or composite material. The coating is a graded coating of at least two layers: an intermediate AlN or Al.sub.x N.sub.y O.sub.z layer and an aluminum oxide or zirconium oxide outer layer. The composition of the coating changes gradually from that of the substrate to that of the AlN or Al.sub.x N.sub.y O.sub.z layer and further to the composition of the aluminum oxide or zirconium oxide outer layer. Other layers may be deposited over the aluminum oxide layer. A CVD process for depositing the graded coating on the substrate is also disclosed.

Magnetic response of hybrid ferromagnetic and antiferromagnetic core-shell nanostructures.

PubMed

Khan, U; Li, W J; Adeela, N; Irfan, M; Javed, K; Wan, C H; Riaz, S; Han, X F

2016-03-21

The synthesis of FeTiO3-Ni(Ni80Fe20) core-shell nanostructures by a two-step method (sol-gel and DC electrodeposition) has been demonstrated. XRD analysis confirms the rhombohedral crystal structure of FeTiO3(FTO) with space group R3[combining macron]. Transmission electron microscopy clearly depicts better morphology of nanostructures with shell thicknesses of ∼25 nm. Room temperature magnetic measurements showed significant enhancement of magnetic anisotropy for the permalloy (Ni80Fe20)-FTO over Ni-FTO core-shell nanostructures. Low temperature magnetic measurements of permalloy-FeTiO3 core-shell structure indicated a strong exchange bias mechanism with magnetic coercivity below the antiferromagnetic Neel temperature (TN = 59 K). The exchange bias is attributed to the alignment of magnetic moments in the antiferromagnetic material at low temperature. Our scheme opens a path towards optimum automotive systems and wireless communications wherein broader bandwidths and smaller sizes are required.

Enhanced photoelectrochemical performance and photocatalytic activity of ZnO/TiO2 nanostructures fabricated by an electrostatically modified electrospinning

NASA Astrophysics Data System (ADS)

Ramos, Pierre G.; Flores, Edson; Sánchez, Luis A.; Candal, Roberto J.; Hojamberdiev, Mirabbos; Estrada, Walter; Rodriguez, Juan

2017-12-01

In this work, ZnO/TiO2 nanostructures were fabricated by an electrostatically modified electrospinning technique using zinc acetate and commercially available TiO2-P25, polyvinyl alcohol, and a solvent. The ZnO/TiO2 nanostructures were fabricated on fluorine-doped tin oxide (FTO) glass substrate by electrospinning of aqueous solution containing different amounts of zinc acetate. The TiO2-P25 nanoparticles were immobilized within zinc acetate/PVA nanofibers. The precursor nanofibers obtained were converted into polycrystalline ZnO and ZnO/TiO2 by calcination at 600 °C. The structure and morphology of the obtained nanostructures were characterized by X-ray diffraction and field emission scanning electron microscopy, respectively. It was found that the TiO2-P25 nanoparticles were attached to the ZnO nanostructures, and the mean diameter of the nanoparticles forming the nanostructures ranged from 31 to 52 nm with increasing the amount of zinc acetate. The incident photon-to-current efficiency (IPCE) spectra of the fabricated nanostructures were measured in a three-electrode cell. The photocatalytic activities of ZnO and ZnO/TiO2 nanostructures were evaluated toward the decomposition of methyl orange. The obtained results evidenced that the coupling of TiO2 with ZnO enhanced the IPCE and improved the photocatalytic activity of ZnO. Particularly, the ZnO/TiO2 nanostructures fabricated with a zinc acetate-to-PVA ratio of 2:3 exhibited the highest IPCE and photocatalytic activity.

Role of defects in one-step synthesis of Cu-doped ZnO nano-coatings by electrodeposition method with enhanced magnetic and electrical properties

NASA Astrophysics Data System (ADS)

Niranjan, K.; Dutta, Subhajit; Varghese, Soney; Ray, Ajoy Kumar; Barshilia, Harish C.

2017-04-01

We report the growth of flower-like ferromagnetic Cu-doped ZnO (CZO) nanostructures using electrochemical deposition on FTO-coated glass substrates. X-ray photoelectron spectroscopy studies affirmed the presence of Cu in ZnO with an oxidation state of 2+. In order to find the optimized dopant concentration, different Cu dopant concentrations of 0.28, 0.30, 0.32, 0.35, 0.38, and 0.40 mM are applied and their magnetic, optical, and electrical properties are studied. Magnetic moment increased with the increasing dopant concentration up to 0.35 mM and then decreased with further increase in the concentration. Diamagnetic pure ZnO showed ferromagnetic nature even with a low doping concentration of 0.28 mM. Band gap increased with the increasing Cu concentration until a value of 0.35 mM and then remained the same for the higher dopant concentrations. It is ascribed to the Burstein-Moss effect. Defect-related broad photoluminescence (PL) peak is observed for the pure ZnO in the visible range. In contrast, Cu-doped samples showed a sharp and intense PL peak at 426 nm due to increased Zn interstitials. Kelvin probe measurements revealed that the Fermi level shifts toward the conduction band for the Cu-doped samples with respect to pure material. Electron transport mechanism in the samples is observed to be dominated by space charge-limited current and Schottky behavior with improved ideality factor up to 0.38 mM Cu.

Effect of photoanode thickness on electrochemical performance of dye sensitized solar cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khatani, Mehboob, E-mail: mkhatani@hotmail.com; Hamid, Nor Hisham, E-mail: hishmid@petronas.com.my; Sahmer, Ahmed Zahrin, E-mail: azclement@yahoo.com

2015-07-22

The thickness of photoanode is crucial as it adsorbed a large amount of dye molecules that provide electrons for generation of electricity in dye sensitized solar cell (DSC). Thus, in order to realize the practical application of DSC, study on various thickness of photoanode need to be carried out to analyze its effect on the electrochemical behavior of dye sensitized solar cell. To enhance the conversion efficiency, an additional layer of TiO{sub 2} using TiCl{sub 4} treatment was deposited prior to the deposition of the photoanode (active area of 1cm{sup 2}) with the thickness of 6, 12, 18, 24, andmore » 30 µm on fluorine doped tin oxide (FTO) glass substrate. The resulting photoanode after the soak in N719 dye for more than 12hrs were used to be assembled in a test cell in combination with liquid electrolyte and counter electrode. The fabricated cells were characterized by solar simulator, ultraviolet-visible spectroscopy (UV-VIS), and electrochemical impedance spectroscopy (EIS). Scanning electron microscopy (SEM) was used to approximate the thickness of photoanode. An optimum power conversion efficiency of 4.54% was obtained for the cell fabricated with 18 µm photoanode thickness. This is attributed to the reduced resistance related to electron transport in the TiO{sub 2}/dye/electrolyte interface as proven by the EIS result. This led to the reduction of internal resistance, the increase in the electron life time and the improvement in the conversion efficiency.« less

Spectroellipsometric detection of silicon substrate damage caused by radiofrequency sputtering of niobium oxide

NASA Astrophysics Data System (ADS)

Lohner, Tivadar; Serényi, Miklós; Szilágyi, Edit; Zolnai, Zsolt; Czigány, Zsolt; Khánh, Nguyen Quoc; Petrik, Péter; Fried, Miklós

2017-11-01

Substrate surface damage induced by deposition of metal atoms by radiofrequency (rf) sputtering or ion beam sputtering onto single-crystalline silicon (c-Si) surface has been characterized earlier by electrical measurements. The question arises whether it is possible to characterize surface damage using spectroscopic ellipsometry (SE). In our experiments niobium oxide layers were deposited by rf sputtering on c-Si substrates in gas mixture of oxygen and argon. Multiple angle of incidence spectroscopic ellipsometry measurements were performed, a four-layer optical model (surface roughness layer, niobium oxide layer, native silicon oxide layer and ion implantation-amorphized silicon [i-a-Si] layer on a c-Si substrate) was created in order to evaluate the spectra. The evaluations yielded thicknesses of several nm for the i-a-Si layer. Better agreement could be achieved between the measured and the generated spectra by inserting a mixed layer (with components of c-Si and i-a-Si applying the effective medium approximation) between the silicon oxide layer and the c-Si substrate. High depth resolution Rutherford backscattering (RBS) measurements were performed to investigate the interface disorder between the deposited niobium oxide layer and the c-Si substrate. Atomic resolution cross-sectional transmission electron microscopy investigation was applied to visualize the details of the damaged subsurface region of the substrate.

Facile preparation of hierarchical nanostructured CuInS2 counter electrodes for dye-sensitized solar cells

NASA Astrophysics Data System (ADS)

Dhas, C. Ravi; Christy, A. Jennifer; Venkatesh, R.; Santhoshi Monica, S. Esther; Panda, Subhendu K.; Subramanian, B.; Ravichandran, K.; Sudhagar, P.; Ezhil Raj, A. Moses

2017-12-01

CuInS2 (CIS) thin films have been synthesized onto the glass substrates for different solvent volumes (10, 30, 50 and 70 ml) by nebulizer spray technique. The effect of solvent volume on the structural, morphological, compositional, optical and electrical properties of CIS thin films has been investigated. X-ray diffraction patterns suggest that the obtained CIS films are polycrystalline with the tetragonal structure. The surface morphology of the prepared CIS films purely depends on the solvent volume. The elemental quantitative investigation and the stoichiometric ratio of the CIS thin films were verified from XPS and EDS. High absorbance with the optical band gap of 1.13 eV was obtained at the higher solvent volume. All the deposited CIS thin films exhibited p-type semiconducting behavior with the high electrical conductivity and carrier concentration. CIS thin films deposited onto the FTO substrate were used as a counter electrode (CE) in dye-sensitized solar cells. CIS CEs possessed high electrocatalytic behavior and fast electron charge transfer at the CE/electrolyte interface. The CIS CE prepared using 50 ml solvent volume generated high energy conversion efficiency of about 3.25%.

Salbutamol intake and substrate oxidation during submaximal exercise.

PubMed

Arlettaz, A; Le Panse, B; Portier, H; Lecoq, A-M; Thomasson, R; De Ceaurriz, J; Collomp, K

2009-01-01

In order to test the hypothesis that salbutamol would change substrate oxidation during submaximal exercise, eight recreationally trained men twice performed 1 h at 60% VO(2) peak after ingestion of placebo or 4 mg of salbutamol. Gas exchange was monitored and blood samples were collected during exercise for GH, ACTH, insulin, and blood glucose and lactate determination. With salbutamol versus placebo, there was no significant difference in total energy expenditure and substrate oxidation, but the substrate oxidation balance was significantly modified after 40 min of exercise. ACTH was significantly decreased with salbutamol during the last 10 min of exercise, whereas no difference was found between the two treatments in the other hormonal and metabolic parameters. The theory that the ergogenic effect of salbutamol results from a change in substrate oxidation has little support during relatively short term endurance exercise, but it is conceivable that longer exercise duration can generate positive findings.

Fluorine compounds for doping conductive oxide thin films

DOEpatents

Gessert, Tim; Li, Xiaonan; Barnes, Teresa M; Torres, Jr., Robert; Wyse, Carrie L

2013-04-23

Methods of forming a conductive fluorine-doped metal oxide layer on a substrate by chemical vapor deposition are described. The methods may include heating the substrate in a processing chamber, and introducing a metal-containing precursor and a fluorine-containing precursor to the processing chamber. The methods may also include adding an oxygen-containing precursor to the processing chamber. The precursors are reacted to deposit the fluorine-doped metal oxide layer on the substrate. Methods may also include forming the conductive fluorine-doped metal oxide layer by plasma-assisted chemical vapor deposition. These methods may include providing the substrate in a processing chamber, and introducing a metal-containing precursor, and a fluorine-containing precursor to the processing chamber. A plasma may be formed that includes species from the metal-containing precursor and the fluorine-containing precursor. The species may react to deposit the fluorine-doped metal oxide layer on the substrate.

Superlubricating graphene and graphene oxide films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sumant, Anirudha V.; Erdemir, Ali; Choi, Junho

A system and method for forming at least one of graphene and graphene oxide on a substrate and an opposed wear member. The system includes graphene and graphene oxide formed by an exfoliation process or solution processing method to dispose graphene and/or graphene oxide onto a substrate. The system further includes an opposing wear member disposed on another substrate and a gas atmosphere of an inert gas like N2, ambient, a humid atmosphere and a water solution.

Hydride transfer made easy in the oxidation of alcohols catalyzed by choline oxidase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gadda, G.; Orville, A.; Pennati, A.

2008-06-08

Choline oxidase (E.C. 1.1.3.17) catalyzes the two-step, four-electron oxidation of choline to glycine betaine with betaine aldehyde as enzyme-associated intermediate and molecular oxygen as final electron acceptor (Scheme 1). The gem-diol, hydrated species of the aldehyde intermediate of the reaction acts as substrate for aldehyde oxidation, suggesting that the enzyme may use similar strategies for the oxidation of the alcohol substrate and aldehyde intermediate. The determination of the chemical mechanism for alcohol oxidation has emerged from biochemical, mechanistic, mutagenetic, and structural studies. As illustrated in the mechanism of Scheme 2, the alcohol substrate is initially activated in the active sitemore » of the enzyme by removal of the hydroxyl proton. The resulting alkoxide intermediate is then stabilized in the enzyme-substrate complex via electrostatic interactions with active site amino acid residues. Alcohol oxidation then occurs quantum mechanically via the transfer of the hydride ion from the activated substrate to the N(5) flavin locus. An essential requisite for this mechanism of alcohol oxidation is the high degree of preorganization of the activated enzyme-substrate complex, which is achieved through an internal equilibrium of the Michaelis complex occurring prior to, and independently from, the subsequent hydride transfer reaction. The experimental evidence that support the mechanism for alcohol oxidation shown in Scheme 2 is briefly summarized in the Results and Discussion section.« less

Oxide film on metal substrate reduced to form metal-oxide-metal layer structure

NASA Technical Reports Server (NTRS)

Youngdahl, C. A.

1967-01-01

Electrically conductive layer of zirconium on a zirconium-oxide film residing on a zirconium substrate is formed by reducing the oxide in a sodium-calcium solution. The reduced metal remains on the oxide surface as an adherent layer and seems to form a barrier that inhibits further reaction.

Oxidase catalysis via aerobically generated hypervalent iodine intermediates

NASA Astrophysics Data System (ADS)

Maity, Asim; Hyun, Sung-Min; Powers, David C.

2018-02-01

The development of sustainable oxidation chemistry demands strategies to harness O2 as a terminal oxidant. Oxidase catalysis, in which O2 serves as a chemical oxidant without necessitating incorporation of oxygen into reaction products, would allow diverse substrate functionalization chemistry to be coupled to O2 reduction. Direct O2 utilization suffers from intrinsic challenges imposed by the triplet ground state of O2 and the disparate electron inventories of four-electron O2 reduction and two-electron substrate oxidation. Here, we generate hypervalent iodine reagents—a broadly useful class of selective two-electron oxidants—from O2. This is achieved by intercepting reactive intermediates of aldehyde autoxidation to aerobically generate hypervalent iodine reagents for a broad array of substrate oxidation reactions. The use of aryl iodides as mediators of aerobic oxidation underpins an oxidase catalysis platform that couples substrate oxidation directly to O2 reduction. We anticipate that aerobically generated hypervalent iodine reagents will expand the scope of aerobic oxidation chemistry in chemical synthesis.

Die singulation method

DOEpatents

Swiler, Thomas P.; Garcia, Ernest J.; Francis, Kathryn M.

2013-06-11

A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with an HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

Die singulation method

DOEpatents

Swiler, Thomas P [Albuquerque, NM; Garcia, Ernest J [Albuquerque, NM; Francis, Kathryn M [Rio Rancho, NM

2014-01-07

A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with a HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

Worm-like mesoporous TiO2 thin films templated using comb copolymer for dye-sensitized solar cells with polymer electrolyte

NASA Astrophysics Data System (ADS)

Lee, Jae Hun; Park, Cheol Hun; Jung, Jung Pyo; Kim, Jong Hak

2015-12-01

A comb copolymer consisting of hydrophobic poly(2-[3-(2H-benzotriazol-2-yl)-4-hydroxyphenyl] ethyl methacrylate) (PBEM) and hydrophilic poly(oxyethylene methacrylate) (POEM) is synthesized via one-pot free radical polymerization. The PBEM-POEM comb copolymer is used as an agent to direct the structure toward one consisting of worm-like mesoporous TiO2 (WM-TiO2) films. The selective, preferential interaction between the titania precursor and the hydrophilic POEM chains is responsible for the formation of a well-organized worm-like mesostructure. The morphology of the WM-TiO2 films is characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). In particular, the effects of film thickness on the optical and electrochemical properties are systematically investigated. The introduction of the WM-TiO2 layer between the nanocrystalline TiO2 (NC-TiO2) layer and fluorine-doped tin oxide (FTO) glass results in increased transmittance of visible light due to an antireflective property, decreased interfacial resistance and suppressed charge recombination at the interfaces of NC-TiO2/FTO glass. As a result, the photovoltaic conversion efficiency of the dye-sensitized solar cell (DSSC) with a polymer electrolyte is improved from 5.3% to 6.6% at an optimum film thickness (310 nm). The obtained efficiency represents a higher efficiency for the N719-based DSSC with a solvent-free, polymer electrolyte.

Lead Sulfide Cathode for Quantum Dot Solar Cells: Electrosynthesis and Characterization

NASA Astrophysics Data System (ADS)

Van Le, Nghiem; Nguyen, Hoang Thai; Le, Hai Viet; Nguyen, Thoa Thi Phuong

2017-01-01

Deposition of lead sulfide (PbS) nanocrystalline thin films onto conducting fluorine-doped tin oxide (FTO) glass has been performed by cyclic voltammetry (CV) in 1.5 mM solution of lead nitrate and sodium thiosulfate at 100 mV s-1 scan rate in the potential range of -1.0 V to 0.0 V versus saturated calomel electrode. X-ray diffraction analysis and scanning electron microscopy revealed formation of cubic PbS crystals with size of 100 nm to 150 nm after 50 cycles. High electrocatalytic activity of the synthesized PbS film for the S2-/S n 2- redox couple, used as a mediator for quantum dot solar cells (QDSCs), was demonstrated by electrochemical impedance spectroscopy and CV measurements. The prepared PbS/FTO was used as a counterelectrode to fabricate PbS-QDSCs with a photoanode consisting of CdS/CdSe quantum dots adsorbed on mesoporous TiO2 film and a polysulfide solution electrolyte. The performance of the PbS-QDSC was compared with a QDSC with a platinum counterelectrode (Pt-QDSC). It was found that, using the same fabrication conditions, the performance of the PbS-QDSC was better than that of the Pt-QDSC. At 1 sun (100 mW cm-2) simulated light, average energy conversion efficiency of 2.14%, short-circuit current of 9.22 mA cm-2, open-circuit potential of 0.50 V, and fill factor of 0.47 were achieved by the fabricated PbS-QDSC.

Characterization of Thermal Oxides on 4H-SiC Epitaxial Substrates Using Fourier-Transform Infrared Spectroscopy.

PubMed

Seki, Hirofumi; Yoshikawa, Masanobu; Kobayashi, Takuma; Kimoto, Tsunenobu; Ozaki, Yukihiro

2017-05-01

Fourier transform infrared (FT-IR) spectra were measured for thermal oxides with different electrical properties grown on 4H-SiC substrates. The peak frequency of the transverse optical (TO) phonon mode was blue-shifted by 5 cm -1 as the oxide-layer thickness decreased to 3 nm. The blue shift of the TO mode indicates interfacial compressive stress in the oxide. Comparison of data for the oxide on a SiC substrate with that for similar oxides on a Si substrate implies that the peak shift of the TO mode at the SiO 2 /SiC interface is larger than that of SiO 2 /Si, which suggests that the interfacial stress for the oxide on the SiC substrate is larger than that on the Si substrate. For the SiO 2 /SiC interfacial region (<3 nm oxide thickness), despite the fact that the blue shift of the TO modes becomes larger while approaching the oxide/SiC interface, the peak frequency of the TO modes red-shifts at the oxide/SiC interface. The peak-frequency shift of the TO mode for the sample without post-oxidation annealing was larger than that for the samples post-annealed in a nitric oxide atmosphere. The channel mobilities are correlated with the degree of shift of the TO mode when the oxide thickness is <3 nm. It appears that the compressive stress at the SiO 2 /SiC interface generates silicon suboxide components and weakens the Si-O bonds. As the result, the TO mode was red-shifted and the oxygen deficiency increased to relax the compressive stress in the oxide with <3 nm thickness. Fourier transform infrared spectroscopy measurements provide unique and useful information about stress and inhomogeneity at the oxide/SiC interface.

C-B3-02: Association of FTO, INSIG2, MC4R, and PCSK1 Obesity SNPs With Binge Eating in Morbidly Obese Patients

PubMed Central

Gerhard, Glenn S; Still, Christopher D; Wood, G Craig; Chu, Xin; Erdman, Robert; Susek, Meghan; Gerst, Heather; Derr, Kim; AlAgha, Mouna; Hartman, Christina; Carey, David; Benotti, Peter

2010-01-01

Background/Aims: Obesity has a strong genetic component. Recent genome-wide association studies have identified single nucleotide polymorphisms (SNPs) in or near over a dozen genes that are related to body mass index (BMI). Despite the association of these SNPs with BMI, the mechanism by which they influence the determination of body weight is not yet known. Recently, the fat- mass and obesity-associated (FTO) obesity SNP was related to energy intake and preference for foods of high caloric density in children. FTO genotype was not associated with resting energy expenditure. We have extended this type of analysis to eating behaviors in the morbidly obese. Methods: DNA was obtained from approximately 900 morbidly obese (BMI>40 kg/m2) patients and used to genotype obesity SNPs in or near the FTO, INSIG2, MC4R, and PCSK1 genes. Binge eating status (normal, episodic overeating, or any binge eating) was determined using the validated Questionnaire on Eating and Weight Patterns (QEWP). Binge eating status was correlated with each individual genotype, the combined obesity allele burden, and the combined homozygous obesity gene burden. Results: Binge eating data was obtained from 640 patients who had completed the QEWP. Of these 640, 116 (18%) were classified as manifesting binge eating behavior. No association was present between heterozygous or homozygous FTO (P=0.59), MC4R (P=0.30), or PSK1 (P=0.77) obesity SNPs. However, 29% of those who were homozygous for the INSIG2 obesity SNP were classified as binge eaters, versus 17% of heterozygous or homozygous normal patients (P=0.006). Association was also found with binge eating status and the presence of 2 or more homozygous obesity genotypes (28% versus 17%, P=0.041), likely due to the INSIG2 gene. Cumulative obesity allele burden (0–8 alleles for the 4 genes) was not associated with binge eating status (P=0.42). Conclusions: The INSIG2 obesity SNP appears to influence binge eating behavior in morbidly obese adults. The FTO obesity SNP appears to influence eating behavior in children suggesting that different genes may influence obesity at different ages. For both genes, excess caloric intake appears to be the major mechanism influencing BMI. How other obesity genes influence body weight regulation has not yet been determined.

Gene Polymorphism Association with Type 2 Diabetes and Related Gene-Gene and Gene-Environment Interactions in a Uyghur Population

PubMed Central

Xiao, Shan; Zeng, Xiaoyun; Fan, Yong; Su, Yinxia; Ma, Qi; Zhu, Jun; Yao, Hua

2016-01-01

Background We investigated the association between 8 single-nucleotide polymorphisms (SNPs) at 3 genetic loci (CDKAL1, CDKN2A/2B and FTO) with type 2 diabetes (T2D) in a Uyghur population. Material/Methods A case-control study of 879 Uyghur patients with T2D and 895 non-diabetic Uyghur controls was conducted at the Hospital of Xinjiang Medical University between 2010 and 2013. Eight SNPs in CDKAL1, CDKN2A/2B and FTO were analyzed using Sequenom MassARRAY®SNP genotyping. Factors associated with T2D were assessed by logistic regression analyses. Gene-gene and gene-environment interactions were analyzed by generalized multifactor dimensionality reduction. Results Genotype distributions of rs10811661 (CDKN2A/2B), rs7195539, rs8050136, and rs9939609 (FTO) and allele frequencies of rs8050136 and rs9939609 differed significantly between diabetes and control groups (all P<0.05). While rs10811661, rs8050136, and rs9939609 were eliminated after adjusting for covariates (P>0.05), rs7195539 distribution differed significantly in co-dominant and dominant models (P<0.05). In gene-gene interaction analysis, after adjusting for covariates the two-locus rs10811661-rs7195539 interaction model had a cross-validation consistency of 10/10 and the highest balanced accuracy of 0.5483 (P=0.014). In gene-environment interaction analysis, the 3-locus interaction model TG-HDL-family history of diabetes had a cross-validation consistency of 10/10 and the highest balanced accuracy of 0.7072 (P<0.001). The 4-locus interaction model, rs7195539-TG-HDL-family history of diabetes had a cross-validation consistency of 8/10 (P<0.001). Conclusions Polymorphisms in CDKN2A/2B and FTO, but not CDKAL1, may be associated with T2D, and alleles rs8050136 and rs9939609 are likely risk alleles for T2D in this population. There were potential interactions among CDKN2A/2B (rs10811661) – FTO (rs7195539) or FTO (rs7195539)-TG-HDL-family history of diabetes in the pathogenesis of T2D in a Uyghur population. PMID:26873362

Nanoplate-like tungsten trioxide (hydrate) films prepared by crystal-seed-assisted hydrothermal reaction

NASA Astrophysics Data System (ADS)

Wang, P.; Yang, L.; Dai, B.; Yang, Z.; Guo, S.; Zhu, J.

2017-07-01

Vertically-aligned WO3 nanoplates on transparent conducting fluorine-doped tin oxide (FTO) glass were prepared by a facile template-free crystal-seed-assisted hydrothermal method. The effects of the hydrothermal temperature and reaction time on the crystal structure and morphology of the products were investigated by XRD and SEM. The XRD results showed that the as-prepared thin films obtained below 150∘C comprised orthorhombic WO3 ṡ H2O and completely converted to monoclinic WO3 at 180∘C. It was also noted that there was a phase transformation from orthorhombic to monoclinic by increasing the reaction time from 1 to 12 h. SEM analysis revealed that WO3 thin films are composed of plate-like nanostructures.

Role of mRNA Methylation in Prostate Cancer

DTIC Science & Technology

2015-02-01

position of adenosine (m6A) is a post-transcriptional modification of mRNA. However, little is known regarding the biological meanings of this epigenetic ...its level is altered in various cancer cell lines. FTO, the fat mass and obesity associated gene, was recently shown as an m6A demethylase. FTO gene...mRNA. However, little is known regarding the biological meanings of this epigenetic regulation of mRNA. Recent technological advances have made it

Polymorphisms FTO rs9939609, PPARG rs1801282 and ADIPOQ rs4632532 and rs182052 but not lifestyle are associated with obesity related-traits in Mexican children.

PubMed

Muñoz-Yáñez, C; Pérez-Morales, R; Moreno-Macías, H; Calleros-Rincón, E; Ballesteros, G; González, R A; Espinosa, J

2016-01-01

Concerning the genetic factors of obesity, no consistent association between populations has been reported, which may be due to the frequency of polymorphisms, the lifestyle of studied populations and its interaction with other factors. We studied a possible association of polymorphisms FTO rs9939609, PPARG rs1801282, and ADIPOQ rs4632532 and rs182052 with obesity phenotypes in 215 Mexican children. Glucose, triglycerides, cholesterol, HDL and LDL were measured. In addition, weight, height, waist circumference and triceps skin thickness were recorded. High-energy diets and sedentary behavior were evaluated with a validated questionnaire. In contrast with other reports, only FTO rs9939609 was associated with obesity related-traits, including BMI (p = 0.03), waist circumference (p = 0.02), triceps skinfold (p = 0.03) and waist/height ratio (p = 0.01), and also with cholesterol levels (p = 0.02) and LDL (p = 0.009). Lower levels of triglycerides (p=0.04) were related with presence of PPARG rs1801282, while ADIPOQ rs4632532 showed an effect on HDL (p = 0.03) levels. On the other hand, diet, physical activity and screen time were not related with obesity. In summary, only FTO rs9939609 was associated with obesity related-traits, while PPARG2 rs1801282 and ADIPOQ rs4632532 were involved in lipid metabolism.

Polymorphisms FTO rs9939609, PPARG rs1801282 and ADIPOQ rs4632532 and rs182052 but not lifestyle are associated with obesity related-traits in Mexican children

PubMed Central

Muñoz-Yáñez, C; Pérez-Morales, R; Moreno-Macías, H; Calleros-Rincón, E; Ballesteros, G; González, R. A; Espinosa, J

2016-01-01

Abstract Concerning the genetic factors of obesity, no consistent association between populations has been reported, which may be due to the frequency of polymorphisms, the lifestyle of studied populations and its interaction with other factors. We studied a possible association of polymorphisms FTO rs9939609, PPARG rs1801282, and ADIPOQ rs4632532 and rs182052 with obesity phenotypes in 215 Mexican children. Glucose, triglycerides, cholesterol, HDL and LDL were measured. In addition, weight, height, waist circumference and triceps skin thickness were recorded. High-energy diets and sedentary behavior were evaluated with a validated questionnaire. In contrast with other reports, only FTO rs9939609 was associated with obesity related-traits, including BMI (p = 0.03), waist circumference (p = 0.02), triceps skinfold (p = 0.03) and waist/height ratio (p = 0.01), and also with cholesterol levels (p = 0.02) and LDL (p = 0.009). Lower levels of triglycerides (p=0.04) were related with presence of PPARG rs1801282, while ADIPOQ rs4632532 showed an effect on HDL (p = 0.03) levels. On the other hand, diet, physical activity and screen time were not related with obesity. In summary, only FTO rs9939609 was associated with obesity related-traits, while PPARG2 rs1801282 and ADIPOQ rs4632532 were involved in lipid metabolism. PMID:27560839

Influence of substrate preparation on the shaping of the topography of the surface of nanoceramic oxide layers

NASA Astrophysics Data System (ADS)

Bara, Marek; Kubica, Marek

2014-02-01

The paper discusses the shaping mechanism and changes occurring in the structure and topography of the surface of nanoceramic oxide layers during their formation. The paper presents the influence of substrate preparation on the surface topography of oxide layers. The layers were produced via hard anodizing on the EN AW-5251 aluminum alloy. The layers obtained were subjected to microscope examinations, image and chemical composition analyses, and stereometric examinations. Heredity of substrate properties in the topography of the surface of nanoceramic oxide layers formed as a result of electrochemical oxidation has been shown.

Resistance training and mitochondrial metabolism

USDA-ARS?s Scientific Manuscript database

Objective: To determine if resistance exercise training improves skeletal muscle substrate oxidative capacity in older adults. Background: A decline in skeletal muscle oxidative capacity occurs with aging. Aerobic exercise increases skeletal muscle’s ability to oxidize multiple substrates. Th...

Selected single-nucleotide polymorphisms in FOXE1, SERPINA5, FTO, EVPL, TICAM1 and SCARB1 are associated with papillary and follicular thyroid cancer risk: replication study in a German population

PubMed Central

Sigurdson, Alice J.; Brenner, Alina V.; Roach, James A.; Goudeva, Lilia; Müller, Jörg A.; Nerlich, Kai; Reiners, Christoph; Schwab, Robert; Pfeiffer, Liliane; Waldenberger, Melanie; Braganza, Melissa; Xu, Li; Sturgis, Erich M.; Yeager, Meredith; Chanock, Stephen J.; Pfeiffer, Ruth M.; Abend, Michael; Port, Matthias

2016-01-01

Several single-nucleotide polymorphisms (SNPs) have been associated with papillary and follicular thyroid cancer (PTC and FTC, respectively) risk, but few have replicated. After analyzing 17525 tag SNPs in 1129 candidate genes, we found associations with PTC risk in SERPINA5, FTO, HEMGN (near FOXE1) and other genes. Here, we report results from a replication effort in a large independent PTC/FTC case–control study conducted in Germany. We evaluated the best tagging SNPs from our previous PTC study and additionally included SNPs in or near FOXE1 and NKX2-1 genes, known susceptibility loci for thyroid cancer. We genotyped 422 PTC and 130 FTC cases and 752 controls recruited from three German clinical centers. We used polytomous logistic regression to simultaneously estimate PTC and FTC associations for 79 SNPs based on log-additive models. We assessed effect modification by body mass index (BMI), gender and age for all SNPs, and selected SNP by SNP interactions. We confirmed associations with PTC and SNPs in FOXE1/HEMGN, SERPINA5 (rs2069974), FTO (rs8047395), EVPL (rs2071194), TICAM1 (rs8120) and SCARB1 (rs11057820) genes. We found associations with SNPs in FOXE1, SERPINA5, FTO, TICAM1 and HSPA6 and FTC. We found two significant interactions between FTO (rs8047395) and BMI (P = 0.0321) and between TICAM1 (rs8120) and FOXE1 (rs10984377) (P = 0.0006). Besides the known associations with FOXE1 SNPs, we confirmed additional PTC SNP associations reported previously. We also found several new associations with FTC risk and noteworthy interactions. We conclude that multiple variants and host factors might interact in complex ways to increase risk of PTC and FTC. PMID:27207655

The association of variants in the FTO gene with longitudinal body mass index profiles in non-Hispanic white children and adolescents.

PubMed

Hallman, D M; Friedel, V C; Eissa, M A H; Boerwinkle, E; Huber, J C; Harrist, R B; Srinivasan, S R; Chen, W; Dai, S; Labarthe, D R; Berenson, G S

2012-01-01

To investigate possible age-related changes in associations between polymorphisms in the fat mass and obesity-associated (FTO) gene and higher body mass index (BMI). Multilevel mixed regression models were used to examine associations between four FTO variants and longitudinal BMI profiles in non-Hispanic white and African American children and adolescents 8-17 years of age from two different longitudinal cohort studies, the Bogalusa Heart Study (BHS) and Project HeartBeat! (PHB). In the BHS, there were 1551 examinations of 478 African Americans and 3210 examinations of 1081 non-Hispanic whites; in PHB, there were 971 examinations of 131 African Americans and 4458 examinations of 505 non-Hispanic whites. In African Americans, no significant FTO associations with BMI were found. In non-Hispanic whites, linkage disequilibrium among all four variants made haplotype analysis superfluous, so we focused on the single-nucleotide polymorphism, rs9939609. In longitudinal multilevel models, the A/A genotype of rs9939609 was associated with higher BMI in non-Hispanic whites in both cohorts at all ages. A significant age-by-genotype interaction found only in the BHS cohort predicted that in those with the A/A genotype, BMI would be ∼0.7 kg m(-2) higher at age 8 and ∼1.6 kg m(-2) higher at age 17 than in those with A/T or T/T genotypes. The design of PHB limited follow-up of any single individual to 4 years, and may have reduced the ability to detect any age-by-genotype interaction in this cohort. The A/A genotype of rs9939609 in the FTO gene is associated with higher longitudinal BMI profiles in non-Hispanic whites from two different cohorts. The association may change with age, with the A/A genotype being associated with a larger BMI difference in late adolescence than in childhood, though this was observed only in the BHS cohort and requires verification.

The (FTO) gene polymorphism is associated with metabolic syndrome risk in Egyptian females: a case- control study.

PubMed

Khella, Mina S; Hamdy, Nadia M; Amin, Ashraf I; El-Mesallamy, Hala O

2017-09-16

Variations within fat mass and obesity associated (FTO) gene had crosstalk with obesity risk in European and some Asian populations. This study was designed to investigate FTO rs9939609 association with metabolic syndrome (MetS) as well as biochemical parameters as plasma glucose, serum triacylglycerol (TAG), total cholesterol (TC) and transaminases enzymes in Arab female population from Egypt. In order to achieve that, FTO gene rs9939609 (A < T) was genotyped using TaqMan SNP Genotyping Assay in a total of 197 females which were enrolled in this study. Fasting levels of serum insulin, lipid profile and plasma glucose, in addition to liver transaminases were measured. The association between the genotype distribution and MetS risk was evaluated using Chi-square and logistic regression tests in a case-control design under different genetic models. The association of genotype distribution with MetS was significant (χ2 = 8.6/P = 0.014) with an increased odds ratio under dominant model (OR = 1.97, P = 0.029 and 95%C.I = 1.07-3.6) and recessive model (OR = 2.95, P = 0.017 and 95%C.I = 1.22-7.22). Moreover, (AA) subjects showed significant lower HDL-C levels (P = 0.009) when compared to (TT) ones. In addition, interestingly subjects with (AA) genotype have significantly higher ALT levels (P = 0.02) that remained significant after correction of major confounders as body mass index and serum triacylglycerols but not after conservative Bonferroni adjustment. The present study shows for first time that FTO gene rs9939609 is genetic risk factor for metabolic syndrome in Egyptian population which may help in understanding the biology of this complex syndrome and highlighted that this association may be through HDL-C component. The association of this genetic polymorphism with ALT levels needs to be studied in other populations with larger sample size.

Selected single-nucleotide polymorphisms in FOXE1, SERPINA5, FTO, EVPL, TICAM1 and SCARB1 are associated with papillary and follicular thyroid cancer risk: replication study in a German population.

PubMed

Sigurdson, Alice J; Brenner, Alina V; Roach, James A; Goudeva, Lilia; Müller, Jörg A; Nerlich, Kai; Reiners, Christoph; Schwab, Robert; Pfeiffer, Liliane; Waldenberger, Melanie; Braganza, Melissa; Xu, Li; Sturgis, Erich M; Yeager, Meredith; Chanock, Stephen J; Pfeiffer, Ruth M; Abend, Michael; Port, Matthias

2016-07-01

Several single-nucleotide polymorphisms (SNPs) have been associated with papillary and follicular thyroid cancer (PTC and FTC, respectively) risk, but few have replicated. After analyzing 17525 tag SNPs in 1129 candidate genes, we found associations with PTC risk in SERPINA5, FTO, HEMGN (near FOXE1) and other genes. Here, we report results from a replication effort in a large independent PTC/FTC case-control study conducted in Germany. We evaluated the best tagging SNPs from our previous PTC study and additionally included SNPs in or near FOXE1 and NKX2-1 genes, known susceptibility loci for thyroid cancer. We genotyped 422 PTC and 130 FTC cases and 752 controls recruited from three German clinical centers. We used polytomous logistic regression to simultaneously estimate PTC and FTC associations for 79 SNPs based on log-additive models. We assessed effect modification by body mass index (BMI), gender and age for all SNPs, and selected SNP by SNP interactions. We confirmed associations with PTC and SNPs in FOXE1/HEMGN, SERPINA5 (rs2069974), FTO (rs8047395), EVPL (rs2071194), TICAM1 (rs8120) and SCARB1 (rs11057820) genes. We found associations with SNPs in FOXE1, SERPINA5, FTO, TICAM1 and HSPA6 and FTC. We found two significant interactions between FTO (rs8047395) and BMI (P = 0.0321) and between TICAM1 (rs8120) and FOXE1 (rs10984377) (P = 0.0006). Besides the known associations with FOXE1 SNPs, we confirmed additional PTC SNP associations reported previously. We also found several new associations with FTC risk and noteworthy interactions. We conclude that multiple variants and host factors might interact in complex ways to increase risk of PTC and FTC. Published by Oxford University Press 2016.

The FTO gene is associated with an atherogenic lipid profile and myocardial infarction in patients with type 2 diabetes: a Genetics of Diabetes Audit and Research Study in Tayside Scotland (Go-DARTS) study.

PubMed

Doney, Alex S F; Dannfald, Jennifer; Kimber, Charlotte H; Donnelly, Louise A; Pearson, Ewan; Morris, Andrew D; Palmer, Colin N A

2009-06-01

Common variation in the fat mass and obesity (FTO)-related gene is associated with increased body fat and susceptibility to type 2 diabetes. We hypothesized that this would also associate with metabolic phenotypes of insulin resistance and increased risk of cardiovascular morbidity and mortality. FTO rs9939609 genotype was determined in 4897 patients with type 2 diabetes in the prospective Genetics of Diabetes Audit and Research Study in Tayside Scotland study. The A allele was associated with lower plasma high-density lipoprotein cholesterol (mean difference, 0.03 mmol/L; P=0.008), higher triglycerides (0.1 mmol/L, P=0.007), higher atherogenic index of plasma (0.03, P=0.003), and, as expected, increased body mass index (0.77 kg/m(2), P=8.8 x 10(-6)). During a mean follow-up of 3.6 years, the A allele was also associated with increased risk (hazard ratio, 2.36; CI, 1.49 to 3.74; P=0.0002) of fatal and nonfatal myocardial infarction (total of 324 events) in a model, including baseline age, gender, prevalent myocardial infarction, smoking status, statin, and insulin use. This association diminished but remained significant when obesity-related traits, such as body mass index, glycohemoglobin, and lipid parameters, were also included (hazard ratio, 2.01; CI, 1.18 to 3.45, P=0.011). There was a strong interaction of FTO genotype and statin use and cardiovascular outcome (P=0.001), such that cardiovascular morbidity and mortality was completely abrogated in individuals who were prescribed statins. The increased fat mass in carriers of the A allele of rs9939609 of FTO is associated not only with increased risk of type 2 diabetes, but also with an increase in atherogenic lipid profile and myocardial infarction in these patients. This variant may, therefore, in the future contribute to more effective targeting of specific preventative therapy.

The missense variation landscape of FTO, MC4R, and TMEM18 in obese children of African Ancestry.

PubMed

Deliard, Sandra; Panossian, Saarene; Mentch, Frank D; Kim, Cecilia E; Hou, Cuiping; Frackelton, Edward C; Bradfield, Jonathan P; Glessner, Joseph T; Zhang, Haitao; Wang, Kai; Sleiman, Patrick M A; Chiavacci, Rosetta M; Berkowitz, Robert I; Hakonarson, Hakon; Zhao, Jianhua; Grant, Struan F A

2013-01-01

Common variation at the loci harboring fat mass and obesity (FTO), melanocortin receptor 4 (MC4R), and transmembrane protein 18 (TMEM18) is consistently reported as being statistically most strongly associated with obesity. Investigations if these loci also harbor rarer missense variants that confer substantially higher risk of common childhood obesity in African American (AA) children were conducted. The exons of FTO, MC4R, and TMEM18 in an initial subset of our cohort were sequenced, that is, 200 obese (BMI ≥ 95 th percentile) and 200 lean AA children (BMI ≤ 5 th percentile). Any missense exonic variants that were uncovered went on to be further genotyped in a further 768 obese and 768 lean (BMI≤50th percentile) children of the same ethnicity. A number of exonic variants were observed from our sequencing effort: seven in FTO, of which four were non-synonymous (A163T, G182A, M400V, and A405V), thirteen in MC4R, of which six were non-synonymous (V103I, N123S, S136A, F202L, N240S, and I251L), and four in TMEM18, of which two were non-synonymous (P2S and V113L). Follow-up genotyping of these missense variants revealed only one significant difference in allele frequency between cases and controls, namely with N240S in MC4R (Fisher's exact P = 0.0001). In summary, moderately rare missense variants within the FTO, MC4R, and TMEM18 genes observed in our study did not confer risk of common childhood obesity in African Americans except for a degree of evidence for one known loss-of-function variant in MC4R. Copyright © 2012 The Obesity Society.

Differences in body mass index according to fat mass- and obesity-associated (FTO) genotype in Mexican patients with bipolar disorder.

PubMed

Díaz-Anzaldúa, Adriana; Ocampo-Mendoza, Yolanda; Hernández-Lagunas, José Octavio; Díaz-Madrid, Federico Alejandro; Romo-Nava, Francisco; Juárez-García, Francisco; Ortega-Ortiz, Hiram; Díaz-Anzaldúa, Alejandro; Gutiérrez-Mora, Doris; Becerra-Palars, Claudia; Berlanga-Cisneros, Carlos

2015-09-01

The prevalence of obesity has dramatically increased in many countries and it is particularly high in patients with bipolar disorder (BD). A region in the first intron of the fat mass- and obesity-associated (FTO) gene, encompassing markers rs9939973, rs8050136, and rs9939609, has been consistently associated with obesity and body mass index (BMI) in different populations. We sought to determine whether FTO is associated with BMI and/or obesity in patients with BD. The sample included 129 Mexican Mestizo patients with bipolar I or bipolar II disorder. After obtaining informed consent, participants were evaluated with the Structured Clinical Interview for DSM-IV Axis I Disorders and weight, height, and body measurements were recorded. DNA was extracted from a 5-mL blood sample and real-time polymerase chain reaction was performed. The results were analyzed with Haploview v4.2 and SPSS v21. Differences in mean BMI were explained by rs8050136 and rs9939609 genotypes, especially by comparing non-carriers and carriers of two copies of the risk allele (Tukey's p ≤ 0.019), with a mean difference in BMI as high as 7.81 kg/m(2) . Differences in BMI were also explained by the interaction of the genotype (rs8050136 and/or rs9939609), the use of second-generation antipsychotics, and the use of mood stabilizers (p ≤ 0.41). Obesity was also associated with these two markers when patients with and without obesity were compared. In patients with BD, differences in BMI may be affected by the presence of FTO risk alleles, especially in homozygous individuals for these variants. Besides evaluating the possible metabolic effects of certain antipsychotics or mood stabilizers, it is important to evaluate the role of other factors such as FTO risk alleles. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Effect of dietary consumption as a modifier on the association between FTO gene variants and excess body weight in children from an admixed population in Brazil: the Social Changes, Asthma and Allergy in Latin America (SCAALA) cohort study.

PubMed

Vilella, Marília; Nunes de Oliveira Costa, Gustavo; Lima Barreto, Maurício; Alexandrina Figueredo, Camila; Maria Alcantara-Neves, Neuza; Cunha Rodrigues, Laura; Maria Alvim de Matos, Sheila; Leovigildo Fiaccone, Rosemeire; Oliveira, Pablo; Rocha, Aline; de Cássia Ribeiro-Silva, Rita

2017-06-01

Previous studies have shown associations of variants of the FTO gene with body weight, but none of these have involved Latin American populations with a high level of miscegenation, as is seen in the north-eastern Brazilian population. This study evaluated the association between SNP in the FTO gene and excess weight in Salvador, Bahia, Brazil. In addition, the effect of diet as a modifier on this association was also investigated. This cross-sectional study included 1191 participants aged 4-11 years, who were genotyped for 400 variants of the FTO gene. Direct anthropometric measures were made and dietary data were obtained by 24-h food recall. Multivariate logistic regression analyses were used to assess the associations of interest. Overall, 11·2 % of the individuals included in the study were overweight/obese. Interactions were identified between the percentage energy intake from proteins and obesity risk linked to the rs62048379 SNP (P interaction=0·01) and also between fat intake (PUFA:SFA ratio) and obesity risk linked to the rs62048379 SNP (P interaction=0·01). The T allele for the variant rs62048379 was positively associated with overweight/obesity in individuals whose percentage energy intake from protein was above the median (OR 2·00; 95 % CI 1·05, 3·82). The rs62048379 SNP was also associated with overweight/obesity in individuals whose PUFA:SFA ratio was below the median (OR 1·63; 95 % CI 1·05, 2·55). The association between FTO gene variants and excess body weight can be modulated by dietary characteristics, particularly by fatty acid distribution and dietary protein intake in children.

Electrochemical immobilization of Fluorescent labelled probe molecules on a FTO surface for affinity detection based on photo-excited current

NASA Astrophysics Data System (ADS)

Haruyama, Tetsuya; Wakabayashi, Ryo; Cho, Takeshi; Matsuyama, Sho-taro

2011-10-01

Photo-excited current can be generated at a molecular interface between a photo-excited molecules and a semi-conductive material in appropriate condition. The system has been recognized for promoting photo-energy devices such as an organic dye sensitized solar-cell. The photo-current generated reactions are totally dependent on the interfacial energy reactions, which are in a highly fluctuated interfacial environment. The authors investigated the photo-excited current reaction to develop a smart affinity detection method. However, in order to perform both an affinity reaction and a photo-excited current reaction at a molecular interface, ordered fabrications of the functional (affinity, photo-excitation, etc.) molecules layer on a semi-conductive surface is required. In the present research, we would like to present the fabrication and functional performance of photo-excited current-based affinity assay device and its application for detection of endocrine disrupting chemicals. On the FTO surface, fluorescent pigment labelled affinity peptide was immobilized through the EC tag (electrochemical-tag) method. The modified FTO produced a current when it was irradiated with diode laser light. However, the photo current decreased drastically when estrogen (ES) coexisted in the reaction solution. In this case, immobilized affinity probe molecules formed a complex with ES and estrogen receptor (ER). The result strongly suggests that the photo-excited current transduction between probe molecule-labelled cyanine pigment and the FTO surface was partly inhibited by a complex that formed at the affinity oligo-peptide region in a probe molecule on the FTO electrode. The bound bulky complex may act as an impediment to perform smooth transduction of photo-excited current in the molecular interface. The present system is new type of photo-reaction-based analysis. This system can be used to perform simple high-sensitive homogeneous assays.

Interfacial development of electrophoretically deposited graphene oxide films on Al alloys

DOE PAGES

Jin, Sumin; Dickerson, James H.; Pham, Viet Hung; ...

2015-07-28

Adhesion between film and substrate is critical for electronic device and coating applications. Interfacial development between electrophoretically deposited graphene oxide films on Al 1100 and Al 5052 alloys were investigated using FT-IR and XPS depth profiling techniques. Obtained results suggest metal ion permeation from the substrates into deposited graphene oxide films. The interface between the films and the substrates were primarily composed of Al-O-C bonds from oxygenated defects on graphene oxide plane rather than expected Al-C formation. Films heat treated at 150 °C had change in microstructure and peak shifts in XPS spectra suggesting change in chemical structure of bondsmore » between the films and the substrates.« less

Improved out-coupling efficiency of organic light emitting diodes fabricated on a TiO2 planarization layer with embedded Si oxide nanostructures

NASA Astrophysics Data System (ADS)

Sung, Young Hoon; Jung, Pil-Hoon; Han, Kyung-Hoon; Kim, Yang Doo; Kim, Jang-Joo; Lee, Heon

2017-10-01

In order to increase the out-coupling efficiency of organic light emitting diodes, conical Si oxide nanostructures were formed on a glass substrate using nanoimprint lithography with hydrogen silsesquioxane. Then, the substrate was planarized with TiO2 nanoparticles. Since TiO2 nanoparticles have a higher refractive index than Si oxide, the surface of substrate is physically flat, but optically undulated in a manner that enables optical scattering and suppression of total internal reflection. Subsequently, OLEDs formed on a substrate with nanostructured Si oxide and a TiO2 planarization layer exhibit a 25% increase in out-coupling efficiency by suppressing total internal reflection.

Calcium regulation of oxidative phosphorylation in rat skeletal muscle mitochondria.

PubMed

Kavanagh, N I; Ainscow, E K; Brand, M D

2000-02-24

Activation of oxidative phosphorylation by physiological levels of calcium in mitochondria from rat skeletal muscle was analysed using top-down elasticity and regulation analysis. Oxidative phosphorylation was conceptually divided into three subsystems (substrate oxidation, proton leak and phosphorylation) connected by the membrane potential or the protonmotive force. Calcium directly activated the phosphorylation subsystem and (with sub-saturating 2-oxoglutarate) the substrate oxidation subsystem but had no effect on the proton leak kinetics. The response of mitochondria respiring on 2-oxoglutarate at two physiological concentrations of free calcium was quantified using control and regulation analysis. The partial integrated response coefficients showed that direct stimulation of substrate oxidation contributed 86% of the effect of calcium on state 3 oxygen consumption, and direct activation of the phosphorylation reactions caused 37% of the increase in phosphorylation flux. Calcium directly activated phosphorylation more strongly than substrate oxidation (78% compared to 45%) to achieve homeostasis of mitochondrial membrane potential during large increases in flux.

Tungsten carbide nanorods with zirconium dioxide composite for low cost with high efficiency Pt-free counter electrode in dye sensitized solar cell

NASA Astrophysics Data System (ADS)

Vijayakumar, P.; Senthil Pandian, M.; Ramasamy, P.

2018-04-01

Tungsten carbide nanorods/Zirconium dioxide (WC-NRs/ZrO2) composite material was used as a counter electrode (CE) for efficient dye-sensitized solar cell (DSSC) fabrication. The prepared WC-NRs/ZrO2 (N-Methyl-2-pyrrolidone (NMP)/2-Propanol) gel is drop casted on the FTO substrate for CE. The morphological analysis was confirmed by FESEM and TEM. Nyquist plot clearly indicates that the NMP based WC-NRs/ZrO2 CE possesses high electrocatalytic activity and faster charge-transfer ability for the reduction of I3- due to the lower charge transfer resistance. The fabricated WC-NRs/ZrO2 (NMP) composite CE is demonstrated with high power conversion efficiency (PCE) of 6.63% in comparison to the WC-NRs/ZrO2 (2-propanol) CE of 2.29% under same conditions.

Complex oxides useful for thermoelectric energy conversion

DOEpatents

Majumdar, Arunava [Orinda, CA; Ramesh, Ramamoorthy [Moraga, CA; Yu, Choongho [College Station, TX; Scullin, Matthew L [Berkeley, CA; Huijben, Mark [Enschede, NL

2012-07-17

The invention provides for a thermoelectric system comprising a substrate comprising a first complex oxide, wherein the substrate is optionally embedded with a second complex oxide. The thermoelectric system can be used for thermoelectric power generation or thermoelectric cooling.

Process for producing metal compounds from graphite oxide

NASA Technical Reports Server (NTRS)

Hung, Ching-Cheh (Inventor)

2000-01-01

A process for providing elemental metals or metal oxides distributed on a carbon substrate or self-supported utilizing graphite oxide as a precursor. The graphite oxide is exposed to one or more metal chlorides to form an intermediary product comprising carbon, metal, chloride, and oxygen This intermediary product can be flier processed by direct exposure to carbonate solutions to form a second intermediary product comprising carbon, metal carbonate, and oxygen. Either intermediary product may be further processed: a) in air to produce metal oxide; b) in an inert environment to produce metal oxide on carbon substrate; c) in a reducing environment to produce elemental metal distributed on carbon substrate. The product generally takes the shape of the carbon precursor.

Process for Producing Metal Compounds from Graphite Oxide

NASA Technical Reports Server (NTRS)

Hung, Ching-Cheh (Inventor)

2000-01-01

A process for providing elemental metals or metal oxides distributed on a carbon substrate or self-supported utilizing graphite oxide as a precursor. The graphite oxide is exposed to one or more metal chlorides to form an intermediary product comprising carbon. metal. chloride. and oxygen This intermediary product can be flier processed by direct exposure to carbonate solutions to form a second intermediary product comprising carbon. metal carbonate. and oxygen. Either intermediary product may be further processed: a) in air to produce metal oxide: b) in an inert environment to produce metal oxide on carbon substrate: c) in a reducing environment. to produce elemental metal distributed on carbon substrate. The product generally takes the shape of the carbon precursor.

Superconducting composite with multilayer patterns and multiple buffer layers

DOEpatents

Wu, Xin D.; Muenchausen, Ross E.

1993-01-01

An article of manufacture including a substrate, a patterned interlayer of a material selected from the group consisting of magnesium oxide, barium-titanium oxide or barium-zirconium oxide, the patterned interlayer material overcoated with a secondary interlayer material of yttria-stabilized zirconia or magnesium-aluminum oxide, upon the surface of the substrate whereby an intermediate article with an exposed surface of both the overcoated patterned interlayer and the substrate is formed, a coating of a buffer layer selected from the group consisting of cerium oxide, yttrium oxide, curium oxide, dysprosium oxide, erbium oxide, europium oxide, iron oxide, gadolinium oxide, holmium oxide, indium oxide, lanthanum oxide, manganese oxide, lutetium oxide, neodymium oxide, praseodymium oxide, plutonium oxide, samarium oxide, terbium oxide, thallium oxide, thulium oxide, yttrium oxide and ytterbium oxide over the entire exposed surface of the intermediate article, and, a ceramic superco n FIELD OF THE INVENTION The present invention relates to the field of superconducting articles having two distinct regions of superconductive material with differing in-plane orientations whereby the conductivity across the boundary between the two regions can be tailored. This invention is the result of a contract with the Department of Energy (Contract No. W-7405-ENG-36).

A non-heme iron-mediated chemical demethylation in DNA and RNA.

PubMed

Yi, Chengqi; Yang, Cai-Guang; He, Chuan

2009-04-21

DNA methylation is arguably one of the most important chemical signals in biology. However, aberrant DNA methylation can lead to cytotoxic or mutagenic consequences. A DNA repair protein in Escherichia coli, AlkB, corrects some of the unwanted methylations of DNA bases by a unique oxidative demethylation in which the methyl carbon is liberated as formaldehyde. The enzyme also repairs exocyclic DNA lesions--that is, derivatives in which the base is augmented with an additional heterocyclic subunit--by a similar mechanism. Two proteins in humans that are homologous to AlkB, ABH2 and ABH3, repair the same spectrum of lesions; another human homologue of AlkB, FTO, is linked to obesity. In this Account, we describe our studies of AlkB, ABH2, and ABH3, including our development of a general strategy to trap homogeneous protein-DNA complexes through active-site disulfide cross-linking. AlkB uses a non-heme mononuclear iron(II) and the cofactors 2-ketoglutarate (2KG) and dioxygen to effect oxidative demethylation of the DNA base lesions 1-methyladenine (1-meA), 3-methylcytosine (3-meC), 1-methylguanine (1-meG), and 3-methylthymine (3-meT). ABH3, like AlkB, works better on single-stranded DNA (ssDNA) and is capable of repairing damaged bases in RNA. Conversely, ABH2 primarily repairs lesions in double-stranded DNA (dsDNA); it is the main housekeeping enzyme that protects the mammalian genome from 1-meA base damage. The AlkB-family proteins have moderate affinities for their substrates and bind DNA in a non-sequence-specific manner. Knowing that these proteins flip the damaged base out from the duplex DNA and insert it into the active site for further processing, we first engineered a disulfide cross-link in the active site to stabilize the Michaelis complex. Based on the detailed structural information afforded by the active-site cross-linked structures, we can readily install a cross-link away from the active site to obtain the native-like structures of these complexes. The crystal structures show a distinct base-flipping feature in AlkB and establish ABH2 as a dsDNA repair protein. They also provide a molecular framework for understanding the demethylation reaction catalyzed by these proteins and help to explain their substrate preferences. The chemical cross-linking method demonstrated here can be applied to trap other labile protein-DNA interactions and can serve as a general strategy for exploring the structural and functional aspects of base-flipping proteins.

Method of making a ceramic with preferential oxygen reactive layer

NASA Technical Reports Server (NTRS)

Wang, Hongyu (Inventor); Luthra, Krishan Lal (Inventor)

2003-01-01

A method of forming an article. The method comprises forming a silicon-based substrate that is oxidizable by reaction with an oxidant to form at least one gaseous product and applying an intermediate layer/coating onto the substrate, wherein the intermediate layer/coating is oxidizable to a nongaseous product by reaction with the oxidant in preference to reaction of the silicon-containing substrate with the oxidant.

3.4-Inch Quarter High Definition Flexible Active Matrix Organic Light Emitting Display with Oxide Thin Film Transistor

NASA Astrophysics Data System (ADS)

Hatano, Kaoru; Chida, Akihiro; Okano, Tatsuya; Sugisawa, Nozomu; Inoue, Tatsunori; Seo, Satoshi; Suzuki, Kunihiko; Oikawa, Yoshiaki; Miyake, Hiroyuki; Koyama, Jun; Yamazaki, Shunpei; Eguchi, Shingo; Katayama, Masahiro; Sakakura, Masayuki

2011-03-01

In this paper, we report a 3.4-in. flexible active matrix organic light emitting display (AMOLED) display with remarkably high definition (quarter high definition: QHD) in which oxide thin film transistors (TFTs) are used. We have developed a transfer technology in which a TFT array formed on a glass substrate is separated from the substrate by physical force and then attached to a flexible plastic substrate. Unlike a normal process in which a TFT array is directly fabricated on a thin plastic substrate, our transfer technology permits a high integration of high performance TFTs, such as low-temperature polycrystalline silicon TFTs (LTPS TFTs) and oxide TFTs, on a plastic substrate, because a flat, rigid, and thermally-stable glass substrate can be used in the TFT fabrication process in our transfer technology. As a result, this technology realized an oxide TFT array for an AMOLED on a plastic substrate. Furthermore, in order to achieve a high-definition AMOLED, color filters were incorporated in the TFT array and a white organic light-emitting diode (OLED) was combined. One of the features of this device is that the whole body of the device can be bent freely because a source driver and a gate driver can be integrated on the substrate due to the high mobility of an oxide TFT. This feature means “true” flexibility.

Electrical characterization of anodic alumina substrate with via-in-pad structure

NASA Astrophysics Data System (ADS)

Kim, Moonjung

2013-10-01

An anodic alumina substrate has been developed as a package substrate for dynamic random access memory devices. Unlike the conventional package substrates commonly made by laminating an epoxy-based core and cladding with copper, this substrate is fabricated using aluminum anodization technology. The anodization process produces a thick aluminum oxide layer on the aluminum substrate to be used as a dielectric layer. Placing copper patterns on the anodic aluminum oxide layer forms a new substrate structure that consists of a layered structure of aluminum, anodic aluminum oxide, and copper. Using selective anodization in the fabrication process, a via structure connecting the top copper layer and bottom aluminum layer is demonstrated. Additionally, by putting vias directly in the bond and ball pads in the substrate design, the via-in-pad structure is applied in this work. These two-layer metal structures and via-in-pad arrangements make routing easier and thus provide more design flexibility. Additionally, this new package substrate has improved the power distribution network impedance given the characteristics of these structures.

Laser surface treatment of porous ceramic substrate for application in solid oxide fuel cells

NASA Astrophysics Data System (ADS)

Mahmod, D. S. A.; Khan, A. A.; Munot, M. A.; Glandut, N.; Labbe, J. C.

2016-08-01

Laser has offered a large number of benefits for surface treatment of ceramics due to possibility of localized heating, very high heating/cooling rates and possibility of growth of structural configurations only produced under non-equilibrium high temperature conditions. The present work investigates oxidation of porous ZrB2-SiC sintered ceramic substrates through treatment by a 1072 ± 10 nm ytterbium fiber laser. A multi-layer structure is hence produced showing successively oxygen rich distinct layers. The porous bulk beneath these layers remained unaffected as this laser-formed oxide scale and protected the substrate from oxidation. A glassy SiO2 structure thus obtained on the surface of the substrate becomes subject of interest for further research, specifically for its utilization as solid protonic conductor in Solid Oxide Fuel Cells (SOFCs).

Investigation into the role of NaCL deposited on oxide and metal substrates in the initiation of hot corrosion

NASA Technical Reports Server (NTRS)

Birks, N.

1981-01-01

The conversion to Na2SO4 of NaCl deposited on oxide substrates was studied as a function of temperature, in air with various SO2 and H2O partial pressures. The substrate was either a pure oxide or an oxide scale growing on a metal specimen. The progress of the reaction was observed using the SEM-EDAX technique to monitor morphological effects and, as far as possible, establish the rate of the process. The physical characteristics of the interaction between salt and substrate were also examined with particular reference to physical damage to the underlying oxide, especially when this is a scale on a metal specimen. An effort was also made to establish the conditions under which liquid phases may form and the mechanisms by which they form.

The role of glutamine and other alternate substrates as energy sources in the fetal rat lung type II cell.

PubMed

Fox, R E; Hopkins, I B; Cabacungan, E T; Tildon, J T

1996-07-01

Glucose has been thought to be the primary substrate for energy metabolism in the developing lung; however, alternate substrates are used for energy metabolism in other organs. To examine the role of alternate substrates in the lung, we measured rates of oxidation of glutamine, glucose, lactate, and 3-hydroxybutyrate in type II pneumocytes isolated from d 19 fetal rat lungs by measuring the production of 14CO2 from labeled substrates. Glutamine had a rate of 24.36 +/- 4.51 nmol 14CO2 produced/ h/mg of protein (mean +/- SEM), whereas lactate had a significantly higher rate, 40.29 +/- 4.42. 3-Hydroxybutyrate had a rate of 14.91 +/- 1.93. The rate of glucose oxidation was 2.13 +/- 0.36, significantly lower than that of glutamine. To examine the interactions of substrates normally found in the intracellular milieu, we measured the effect of unlabeled substrates as competitors on labeled substrate. This identifies multiple metabolic compartments of energy metabolism. Glucose, but not lactate, inhibited the oxidation of glutamine, suggesting a compartmentation of tricarboxylic acid cycle activity, rather than simple dilution by glucose. Glucose and lactate had reciprocal inhibition. Our data suggest at least two separate compartments in the type II cells for substrate oxidation, one for glutamine metabolism and a second for glucose metabolism. In summary, we have documented that glutamine and other alternate substrates are oxidized preferentially over glucose for energy metabolism in the d 19 fetal rat lung type II pneumocyte. In addition, we have delineated some of the compartmentation that occurs within the developing type II cell, which may determine how these substrates are used.

Substrate Selection for Fundamental Studies of Electrocatalysts and Photoelectrodes: Inert Potential Windows in Acidic, Neutral, and Basic Electrolyte

PubMed Central

Gorlin, Yelena; Jaramillo, Thomas F.

2014-01-01

The selection of an appropriate substrate is an important initial step for many studies of electrochemically active materials. In order to help researchers with the substrate selection process, we employ a consistent experimental methodology to evaluate the electrochemical reactivity and stability of seven potential substrate materials for electrocatalyst and photoelectrode evaluation. Using cyclic voltammetry with a progressively increased scan range, we characterize three transparent conducting oxides (indium tin oxide, fluorine-doped tin oxide, and aluminum-doped zinc oxide) and four opaque conductors (gold, stainless steel 304, glassy carbon, and highly oriented pyrolytic graphite) in three different electrolytes (sulfuric acid, sodium acetate, and sodium hydroxide). We determine the inert potential window for each substrate/electrolyte combination and make recommendations about which materials may be most suitable for application under different experimental conditions. Furthermore, the testing methodology provides a framework for other researchers to evaluate and report the baseline activity of other substrates of interest to the broader community. PMID:25357131

Substrate Selection for Fundamental Studies of Electrocatalysts and Photoelectrodes: Inert Potential Windows in Acidic, Neutral, and Basic Electrolyte

DOE PAGES

Benck, Jesse D.; Pinaud, Blaise A.; Gorlin, Yelena; ...

2014-10-30

The selection of an appropriate substrate is an important initial step for many studies of electrochemically active materials. In order to help researchers with the substrate selection process, we employ a consistent experimental methodology to evaluate the electrochemical reactivity and stability of seven potential substrate materials for electrocatalyst and photoelectrode evaluation. Using cyclic voltammetry with a progressively increased scan range, we characterize three transparent conducting oxides (indium tin oxide, fluorine-doped tin oxide, and aluminum-doped zinc oxide) and four opaque conductors (gold, stainless steel 304, glassy carbon, and highly oriented pyrolytic graphite) in three different electrolytes (sulfuric acid, sodium acetate, andmore » sodium hydroxide). Here, we determine the inert potential window for each substrate/electrolyte combination and make recommendations about which materials may be most suitable for application under different experimental conditions. Furthermore, the testing methodology provides a framework for other researchers to evaluate and report the baseline activity of other substrates of interest to the broader community.« less

Thermoelectric material including conformal oxide layers and method of making the same using atomic layer deposition

DOEpatents

Cho, Jung Young; Ahn, Dongjoon; Salvador, James R.; Meisner, Gregory P.

2016-06-07

A thermoelectric material includes a substrate particle and a plurality of conformal oxide layers formed on the substrate particle. The plurality of conformal oxide layers has a total oxide layer thickness ranging from about 2 nm to about 20 nm. The thermoelectric material excludes oxide nanoparticles. A method of making the thermoelectric material is also disclosed herein.

Glutamine metabolism in a holostean (Amia calva) and teleost fish (Salvelinus namaycush).

PubMed

Chamberlin, M E; Glemet, H C; Ballantyne, J S

1991-01-01

Amino acid metabolism was examined in mitochondria from the lateral red muscle of a teleost (lake char, Salvelinus namaycush) and a nonteleost fish (bowfin, Amia calva). Isolated mitochondria oxidize a wide variety of substrates and have high respiratory control ratios. In both species, glutamine is oxidized more rapidly than any other amino acid. The rate of glutamine oxidation by bowfin mitochondria exceeds that of lake char mitochondria, and the bowfin displays correspondingly higher levels of mitochondrial phosphate-dependent glutaminase. It is suggested that amino acids in general, and glutamine in particular, are important oxidative substrates for nonteleost red muscle. The teleost red muscle, however, may rely on both glutamine and fatty acids as oxidative substrates. It appears that glutamate derived from glutamine is oxidized primarily via glutamate dehydrogenase, whereas exogenous glutamate is oxidized primarily via aspartate aminotransferase. Complete oxidation of glutamine may be accomplished in the absence of other substrates by conversion of glutamine-derived malate to pyruvate via malic enzyme. To assess the relative abilities of various tissues to synthesize and oxidize glutamine, the activities of glutamine synthetase and glutaminase were measured. The results of these studies indicate that the organization of glutamine metabolism of fish differs markedly from that in mammals.

Population of Nitrifying Bacteria and Nitrification in Ammonium Saturated Clinoptilolite

NASA Technical Reports Server (NTRS)

McGilloway, R. L.; Weaver, R. W.; Ming, Douglas W.; Gruener, J.

1999-01-01

As humans begin to spend longer periods of time in space, plants will be incorporated into life support systems. Ammonium saturated clinoptilolite is one plant growth substrate but a balance between ammonium and nitrate is needed. A laboratory study was conducted to determine effects of nitrifying bacteria on ammonium concentrations and kinetics of nitrification. Columns containing clinoptilolite substrate amended with nitrifying bacteria obtained from soil enrichment were analyzed weekly for a 90 day period. The enrichment culture initially contained 1 x 10(exp 5) ammonium oxidizing bacteria and 1 x 10(exp 2) nitrite oxidizing bacteria per gram of substrate. Populations of ammonium oxidizing bacteria increased to 1 x 10(exp 6) and nitrite oxidizing bacteria increased to 1 x 10(exp 3) per gram of substrate. The nitrification rate was approximately 0.25mg NO3(-)-N/kg.hr. Experiments were also conducted to enumerate nitrifying bacteria in a clinoptilolite substrate used to grow wheat (Triticum aestivum L.). Seventy days following the initial inoculation with an unknown number of commercial nitrifying bacteria, 1 x 10(exp 5) ammonium oxidizing bacteria per gram of substrate were present. The number of nitrite oxidizing bacteria was between 1 x 10(exp 3) to 10(exp 4) per gram of substrate as measured by the most probable number method. Nitrification rates were approximately 0.20mg NO3(-)-N/kg.hr. Clinoptilolite readily exchanged sufficient concentrations of ammonium to support nitrifying bacteria and they survived well in this medium.

Solar cell collector and method for producing same

NASA Technical Reports Server (NTRS)

Evans, J. C., Jr. (Inventor)

1978-01-01

A transparent, conductive collector layer containing conductive metal channels is formed as a layer on a photovoltaic substrate by coating a photovoltaic substract with a conductive mixed metal layer. A heat sink having portions protruding from one of its surfaces is attached. These protruding portions define a continuous pattern in combination with recessed regions among them such that they are in contact with the conductive layer of the photovoltaic substrate. Heating the substrate while simultaneously oxidizing the portions of the conductive layer exposed to a gaseous oxidizing substance forced into the recessed regions of the heat sink, creates a transparent metal oxide layer on the substrate. A continous pattern of highly conductive metal channels is contained in the metal oxide layer.

Application of a mixed metal oxide catalyst to a metallic substrate

NASA Technical Reports Server (NTRS)

Sevener, Kathleen M. (Inventor); Lohner, Kevin A. (Inventor); Mays, Jeffrey A. (Inventor); Wisner, Daniel L. (Inventor)

2009-01-01

A method for applying a mixed metal oxide catalyst to a metallic substrate for the creation of a robust, high temperature catalyst system for use in decomposing propellants, particularly hydrogen peroxide propellants, for use in propulsion systems. The method begins by forming a prepared substrate material consisting of a metallic inner substrate and a bound layer of a noble metal intermediate. Alternatively, a bound ceramic coating, or frit, may be introduced between the metallic inner substrate and noble metal intermediate when the metallic substrate is oxidation resistant. A high-activity catalyst slurry is applied to the surface of the prepared substrate and dried to remove the organic solvent. The catalyst layer is then heat treated to bind the catalyst layer to the surface. The bound catalyst layer is then activated using an activation treatment and calcinations to form the high-activity catalyst system.

Functionalization of Ti99.2 substrates surface by hybrid treatment investigated with spectroscopic methods

NASA Astrophysics Data System (ADS)

Jasinski, Jaroslaw Jan; Lubas, Malgorzata; Kurpaska, Lukasz; Napadlek, Wojciech; Sitarz, Maciej

2018-07-01

The article presents spectroscopic investigation of Ti 99.2 based functional substrates formed by hybrid oxidation process. Surface treatments were performed by combining methods of fluidized bed atmospheric diffusion treatment (FADT) with physical vapor deposition (PVD) - magnetron sputtering and laser surface texturing (LST) treatments. The processes were implemented to form a titanium diffusive layer saturated with oxygen in the substrate and a tight homogeneous oxide coating on Ti surface deposited with magnetron sputtering or laser texturing technique. The hybrid treatment was realized in Al2O3 fluidized bed reactor with air atmosphere, at 640 °C for 8 h and 12 h. At the same time, magnetron sputtering with the use of TiO2 target at a pressure of 3 × 102 mbar and laser surface texturing treatment with Nd:YAG λ = 1064 nm was performed. In order to investigate the effects of hybrid oxidation, microscopic (AFM, CLSM, SEM/SEM-EDX), spectroscopic (RS) and X-ray investigations (GID-XRD) were performed. Applied hybrid technique made possible to combine the effects of the generated layers and to reduce the stresses in the area of the PVD coating/oxidized Ti substrate interface. Furthermore, Raman spectroscopy results obtained at oxide layers manufactured with different variants of oxidation allowed detailed analysis of the created oxides. The coatings have shown structure with a Tiα(O) diffusion zone, a TiO2 rutile and anatase oxide zone deposited and textured on the substrate. Phase composition and morphology of these oxides is essential for the osseointegration process i.e. intensity of hydroxyapatite growing on the implant surface. Performed processes influenced the surface roughness parameter and cause the increase of substrate functional properties, which are important for biomedical applications.

Postprandial energy metabolism and substrate oxidation in response to the inclusion of a sugar- or non-nutritive sweetened beverage with meals differing in protein content

USDA-ARS?s Scientific Manuscript database

Protein-rich diets may promote achieving and maintaining a healthy body weight by increasing energy metabolism and substrate oxidation, especially fat oxidation. Sugar sweetened beverages (SSBs) are considered a major contributor to the obesogenic food environment and may decrease fat oxidation. The...

Association of gene polymorphism of the fat mass and obesity associated gene with metabolic syndrome: a retrospective cohort study in Japanese workers.

PubMed

Kawajiri, Tomoka; Osaki, Yoneatsu; Kishimoto, Takuji

2012-06-01

To investigate whether gene polymorphism of the fat mass and obesity associated gene (FTO) is associated with metabolic syndrome (MS), we used two MS criteria, the National Cholesterol Education Program-Adult Treatment panel III (NCEP-ATPIII) definition in 2003 and the Japanese definition in 2005. Subjects were respectively 859 and 865 Japanese workers at a company in Shimane Prefecture, Japan. They were non-MS individuals in 1998 and had regular health checkups between 1998 and 2006. The Cox proportional hazard regression was used to predict MS. Three SNPs in the FTO, rs9939609, rs1121980 and rs1558902, were genotyped by the TaqMan PCR assay and a retrospective study was performed. The three SNPs in the FTO were significantly associated with body mass index, and rs1121980 and rs1558902 were associated with fasting plasma glucose. MS defined by the NCEP-ATPIII definition was significantly associated with additive and dominant models of rs9939609 and rs1121980, and the dominant model of rs1558902, even after adjusting for confounding factors such as age, sex and lifestyle. MS defined by the Japanese definition was significantly associated with the additive model of rs1121980 and additive and dominant models of rs1558902 in multivariate analysis. These results suggested that FTO gene polymorphisms, rs9939609, rs1121980 and rs1558902, were associated with an increased risk of MS among Japanese workers.

Long-term effects of Garcinia cambogia/Glucomannan on weight loss in people with obesity, PLIN4, FTO and Trp64Arg polymorphisms.

PubMed

Maia-Landim, Andrea; Ramírez, Juan M; Lancho, Carolina; Poblador, María S; Lancho, José L

2018-01-24

Overweight and obesity are considered major health problems that contribute to increase mortality and quality of life. Both conditions have a high prevalence across the world reaching epidemic numbers. Our aim was to evaluate the effects of the administration of Garcinia cambogia (GC) and Glucomannan (GNN) on long-term weight loss in people with overweight or obesity. Prospective, not-randomized controlled intervention trial was conducted. We treated 214 subjects with overweight or obesity with GC and GNN (500 mg twice a day, each) for 6 months evaluating weight, fat mass, visceral fat, basal metabolic rate, and lipid and glucose blood profiles comparing them with basal values. Some patients were carriers of polymorphisms PLIN4 -11482G > A-, fat mass and obesity-associated (FTO) -rs9939609 A/T- and β-adrenergic receptor 3 (ADRB3) -Trp64Arg. Treatment produced weight loss, reducing fat mass, visceral fat, lipid and blood glucose profiles while increasing basal metabolic rate. Results were independent of sex, age or suffering from hypertension, diabetes mellitus type 2 or dyslipidemia and were attenuated in carriers of PLIN4, FTO, Trp64Arg polymorphisms. Administration of GC and GNN reduce weight and improve lipid and glucose blood profiles in people with overweight or obesity, although the presence of polymorphisms PLIN4, FTO and ADRB3 might hinder in some degree these effects. ISRCTN78807585, 19 September 2017, retrospective study.

Optimization of exchange bias in Co/CoO magnetic nanocaps by tuning deposition parameters

NASA Astrophysics Data System (ADS)

Sharma, A.; Tripathi, J.; Ugochukwu, K. C.; Tripathi, S.

2017-03-01

In the present work, we report exchange bias tuning by varying thin film deposition parameters such as synthesis method and underlying layer patterning. The patterned substrates for this study were prepared by self-assembly of polystyrene (PS) latex spheres ( 530 nm) on Si (100) substrate. The desired magnetic nanocaps composed of CoO/Co bilayer film on these patterned substrates were prepared by molecular beam epitaxy technique under ultra-high vacuum conditions. For this, a Co layer of 10 nm thickness was deposited on the substrates and then oxidized in-situ to form CoO/Co/PS in-situ oxidized film or ex-situ in ambiance which also gives CoO/Co/PS naturally oxidized film. Simultaneously, reference thin films of Co ( 10 nm) were also prepared on plane Si substrate and similar oxidation treatments were performed on them respectively. The magnetic properties studied using SQUID technique revealed higher exchange bias ( 1736 Oe) in the in-situ oxidized Co/PS film as compared to that in naturally oxidized Co/PS film ( 1544 Oe) and also compared to the reference film. The observed variations in the magnetic properties are explained in terms of surface patterning induced structural changes of the deposited films and different oxidation methods.

Chloroperoxidase-catalyzed oxidation of 4,6-dimethyldibenzothiophene as dimer complexes: evidence for kinetic cooperativity.

PubMed

Torres, Eduardo; Aburto, Jorge

2005-05-15

A sigmoidal kinetic behavior of chloroperoxidase for the oxidation of 4,6-dimethyldibenzothiophene (4,6-DMDBT) in water-miscible organic solvent is for the first time reported. Kinetics of 4,6-DMDBT oxidation showed a cooperative profile probably due to the capacity of chloroperoxidase to recognize a substrate dimer (pi-pi dimer) in its active site. Experimental evidence is given for dimer formation and its presence in the active site of chloroperoxidase. The kinetic data were adjusted for a binding site able to interact with either monomer or dimer substrates, producing a cooperative model describing a one-site binding of two related species. Determination of kinetics constants by iterative calculations of possible oxidation paths of 4,6-DMDBT suggests that kinetics oxidation of dimer substrate is preferred when compared to monomer oxidation. Steady-state fluorometry of substrate in the absence and presence of chloroperoxidase, described by the spectral center of mass, supports this last conclusion.

RF sputtered silicon and hafnium nitrides as applied to 440C steel

NASA Technical Reports Server (NTRS)

Grill, A.; Aron, P. R.

1984-01-01

Silicon nitride and hafnium nitride coatings were deposited on oxidized and unoxidized 440C stainless steel substrates. Sputtering was done in mixtures of argon and nitrogen gases from pressed powder silicon nitride and from hafnium metal targets. The coatings and the interface between the coating and substrate were investigated by X-ray diffractometry, scanning electron microscopy, energy dispersive X-ray analysis and Auger electron spectroscopy. Oxide was found at all interfaces with an interface width of at least 600 A for the oxidized substrates and at least 300 A for the unoxidized substrates. Scratch test results demonstrate that the adhesion of hafnium nitride to both oxidized and unoxidized 440C is superior to that of silicon nitride. Oxidized 440C is found to have increased adhesion, to both nitrides, over that of unoxidized 440C. Coatings of both nitrides deposited at 8 mtorr were found to have increased adhesion to both oxidized and unoxidized 440C over those deposited at 20 mtorr.

Liquid flow cells having graphene on nitride for microscopy

DOEpatents

Adiga, Vivekananda P.; Dunn, Gabriel; Zettl, Alexander K.; Alivisatos, A. Paul

2016-09-20

This disclosure provides systems, methods, and apparatus related to liquid flow cells for microscopy. In one aspect, a device includes a substrate having a first and a second oxide layer disposed on surfaces of the substrate. A first and a second nitride layer are disposed on the first and second oxide layers, respectively. A cavity is defined in the first oxide layer, the first nitride layer, and the substrate, with the cavity including a third nitride layer disposed on walls of the substrate and the second oxide layer that define the cavity. A channel is defined in the second oxide layer. An inlet port and an outlet port are defined in the second nitride layer and in fluid communication with the channel. A plurality of viewports is defined in the second nitride layer. A first graphene sheet is disposed on the second nitride layer covering the plurality of viewports.

Direct growth of cerium oxide nanorods on diverse substrates for superhydrophobicity and corrosion resistance

NASA Astrophysics Data System (ADS)

Cho, Young Jun; Jang, Hanmin; Lee, Kwan-Soo; Kim, Dong Rip

2015-06-01

Superhydrophobic surfaces with anti-corrosion properties have attracted great interest in many industrial fields, particularly to enhance the thermal performance of offshore applications such as heat exchangers, pipelines, power plants, and platform structures. Nanostructures with hydrophobic materials have been widely utilized to realize superhydrophobicity of surfaces, and cerium oxide has been highlighted due to its good corrosion resistive and intrinsically hydrophobic properties. However, few studies of direct growth of cerium oxide nanostructures on diverse substrates have been reported. Herein we report a facile hydrothermal method to directly grow cerium oxide nanorods on diverse substrates, such as aluminum alloy, stainless steel, titanium, and silicon. Diverse substrates with cerium oxide nanorods exhibited superhydrophobicity with no hydrophobic modifiers on their surfaces, and showed good corrosion resistive properties in corrosive medium. We believe our method could pave the way for realization of scalable and sustainable corrosion resistive superhydrophobic surfaces in many industrial fields.

Application of diffusion barriers to the refractory fibers of tungsten, columbium, carbon and aluminum oxide

NASA Technical Reports Server (NTRS)

Douglas, F. C.; Paradis, E. L.; Veltri, R. D.

1973-01-01

A radio frequency powered ion-plating system was used to plate protective layers of refractory oxides and carbide onto high strength fiber substrates. Subsequent overplating of these combinations with nickel and titanium was made to determine the effectiveness of such barrier layers in preventing diffusion of the overcoat metal into the fibers with consequent loss of fiber strength. Four substrates, five coatings, and two metal matrix materials were employed for a total of forty material combinations. The substrates were tungsten, niobium, NASA-Hough carbon, and Tyco sapphire. The diffusion-barrier coatings were aluminum oxide, yttrium oxide, titanium carbide, tungsten carbide with 14% cobalt addition, and zirconium carbide. The metal matrix materials were IN 600 nickel and Ti 6/4 titanium. Adhesion of the coatings to all substrates was good except for the NASA-Hough carbon, where flaking off of the oxide coatings in particular was observed.

Effects of substrate temperature on properties of pulsed dc reactively sputtered tantalum oxide films

NASA Astrophysics Data System (ADS)

Jain, Pushkar; Juneja, Jasbir S.; Bhagwat, Vinay; Rymaszewski, Eugene J.; Lu, Toh-Ming; Cale, Timothy S.

2005-05-01

The effects of substrate heating on the stoichiometry and the electrical properties of pulsed dc reactively sputtered tantalum oxide films over a range of film thickness (0.14 to 5.4 μm) are discussed. The film stoichiometry, and hence the electrical properties, of tantalum oxide films; e.g., breakdown field, leakage current density, dielectric constant, and dielectric loss are compared for two different cases: (a) when no intentional substrate/film cooling is provided, and (b) when the substrate is water cooled during deposition. All other operating conditions are the same, and the film thickness is directly related to deposition time. The tantalum oxide films deposited on the water-cooled substrates are stoichiometric, and exhibit excellent electrical properties over the entire range of film thickness. ``Noncooled'' tantalum oxide films are stoichiometric up to ~1 μm film thickness, beyond that the deposited oxide is increasingly nonstoichiometric. The presence of partially oxidized Ta in thicker (>~1 μm) noncooled tantalum oxide films causes a lower breakdown field, higher leakage current density, higher apparent dielectric constant, and dielectric loss. The growth of nonstoichiometric tantalum oxide in thicker noncooled films is attributed to decreased surface oxygen concentration due to oxygen recombination and desorption at higher film temperatures (>~100 °C). The quantitative results presented reflect experience with a specific piece of equipment; however, the procedures presented can be used to characterize deposition processes in which film stoichiometry can change.

Synthesis of high T.sub.C superconducting coatings and patterns by melt writing and oxidation of metallic precursor alloys

DOEpatents

Gao, Wei; Vander Sande, John B.

1998-01-01

A method is provided for fabrication of superconducting oxides and superconducting oxide composites and for joining superconductors to other materials. A coating of a molten alloy containing the metallic elements of the oxide is applied to a substrate surface and oxidized to form the superconducting oxide. A material can be contacted to the molten alloy which is subsequently oxidized joining the material to the resulting superconducting oxide coating. Substrates of varied composition and shape can be coated or joined by this method.

Synthesis of high {Tc} superconducting coatings and patterns by melt writing and oxidation of metallic precursor alloys

DOEpatents

Gao, W.; Vander Sande, J.B.

1998-07-28

A method is provided for fabrication of superconducting oxides and superconducting oxide composites and for joining superconductors to other materials. A coating of a molten alloy containing the metallic elements of the oxide is applied to a substrate surface and oxidized to form the superconducting oxide. A material can be contacted to the molten alloy which is subsequently oxidized joining the material to the resulting superconducting oxide coating. Substrates of varied composition and shape can be coated or joined by this method. 5 figs.

Fabrication of heterojunction solar cells by improved tin oxide deposition on insulating layer

DOEpatents

Feng, Tom; Ghosh, Amal K.

1980-01-01

Highly efficient tin oxide-silicon heterojunction solar cells are prepared by heating a silicon substrate, having an insulating layer thereon, to provide a substrate temperature in the range of about 300.degree. C. to about 400.degree. C. and thereafter spraying the so-heated substrate with a solution of tin tetrachloride in a organic ester boiling below about 250.degree. C. Preferably the insulating layer is naturally grown silicon oxide layer.

CHEMICAL SOLUTION DEPOSITION BASED OXIDE BUFFERS AND YBCO COATED CONDUCTORS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paranthaman, Mariappan Parans

We have reviewed briefly the growth of buffer and high temperature superconducting oxide thin films using a chemical solution deposition (CSD) method. In the Rolling-Assisted Biaxially Textured Substrates (RABiTS) process, developed at Oak Ridge National Laboratory, utilizes the thermo mechanical processing to obtain the flexible, biaxially oriented copper, nickel or nickel-alloy substrates. Buffers and Rare Earth Barium Copper Oxide (REBCO) superconductors have been deposited epitaxially on the textured nickel alloy substrates. The starting substrate serves as a template for the REBCO layer, which has substantially fewer weak links. Buffer layers play a major role in fabricating the second generation REBCOmore » wire technology. The main purpose of the buffer layers is to provide a smooth, continuous and chemically inert surface for the growth of the REBCO film, while transferring the texture from the substrate to the superconductor layer. To achieve this, the buffer layers need to be epitaxial to the substrate, i.e. they have to nucleate and grow in the same bi-axial texture provided by the textured metal foil. The most commonly used RABiTS multi-layer architectures consist of a starting template of biaxially textured Ni-5 at.% W (Ni-W) substrate with a seed (first) layer of Yttrium Oxide (Y2O3), a barrier (second) layer of Yttria Stabilized Zirconia (YSZ), and a Cerium Oxide (CeO2) cap (third) layer. These three buffer layers are generally deposited using physical vapor deposition (PVD) techniques such as reactive sputtering. On top of the PVD template, REBCO film is then grown by a chemical solution deposition. This article reviews in detail about the list of oxide buffers and superconductor REBCO films grown epitaxially on single crystal and/or biaxially textured Ni-W substrates using a CSD method.« less

Enzymatic synthesis of polymers containing nicotinamide mononucleotide

NASA Technical Reports Server (NTRS)

Liu, Rihe

1995-01-01

Nicotinamide mononucleoside 5'-diphosphate in its reduced form is an excellent substrate for polynucleotide phosphorylase from Micrococcus luteus both in de novo polymerization reactions and in primer extension reactions. The oxidized form of the diphosphate is a much less efficient substrate; it can be used to extend primers but does not oligomerize in the absence of a primer. The cyanide adduct of the oxidized substrate, like the reduced substrate, polymerizes efficiently. Loss of cyanide yields high molecular weight polymers of the oxidized form. Terminal transferase from calf thymus accepts nicotinamide mononucleoside 5'-triphosphate as a substrate and efficiently adds one residue to the 3'-end of an oligodeoxynucleotide. T4 polynucleotide kinase accepts oligomers of nicotinamide mononucleotide as substrates. However, RNA polymerases do not incorporate nicotinamide mononucleoside 5'-triphosphate into products on any of the templates that we used.

Enzymatic Synthesis of Polymers Containing Nicotinamide Mononucleotide

NASA Technical Reports Server (NTRS)

Liu, Rihe; Orgel, Leslie E.

1995-01-01

Nicotinamide mononucleoside 5'-diphosphate in its reduced form is an excellent substrate for polynucleotide phosphorylase from Micrococcus luteus both in de novo polymerization reactions and in primer extension reactions. The oxidized form of the diphosphate is a much less efficient substrate; it can be used to extend primers but does not oligomerize in the absence of a primer. The cyanide adduct of the oxidized substrate, like the reduced substrate, polymerizes efficiently. Loss of cyanide yields high molecular weight polymers of the oxidized form. Terminal transferase from calf thymus accepts nicotinamide mononucleoside 5'-triphosphate as a substrate and efficiently adds one residue to the 3'-end of an oligodeoxynucleotide. T4 polynucleotide kinase accepts oligomers of nicotinamide mononucleotide as substrates. However, RNA polymerases do not incorporate nicotinamide mononucleoside 5'-triphosphate into products on any of the templates that we used.

A Review of the Effect of Dietary Composition on Fasting Substrate Oxidation in Healthy and Overweight Subjects.

PubMed

Whelan, Megan E; Wright, Olivia R L; Hickman, Ingrid J

2016-01-01

The purpose of this review was to assess existing evidence on the effects of chronic dietary macronutrient composition on substrate oxidation during a fasted state in healthy and overweight subjects. A systematic review of studies was conducted across five databases. Studies were included if they were English language studies of human adults, ≥19 years, used indirect calorimetry (ventilated hood technique), specified dietary macronutrient composition, and measured substrate oxidation. There was no evidence that variations of a typical, non-experimental diet influenced rate or ratio of substrate utilization, however there may be an upper and lower threshold for when macronutrient composition may directly alter preferences for fuel oxidation rates during a fasted state. This review indicates that macronutrient composition of a wide range of typical, non-experimental dietary fat and carbohydrate intakes has no effect on fasting substrate oxidation. This suggests that strict control of dietary intake prior to fasting indirect calorimetry measurements may be an unnecessary burden for study participants. Further research into the effects of long-term changes in isocaloric macronutrient shift is required.

Substrate and nutrient limitation of ammonia-oxidizing bacteria and archaea in temperate forest soil

Treesearch

J.S. Norman; J.E. Barrett

2014-01-01

Ammonia-oxidizing microbes control the rate-limiting step of nitrification, a critical ecosystem process, which affects retention and mobility of nitrogen in soil ecosystems. This study investigated substrate (NH4þ) and nutrient (K and P) limitation of ammonia-oxidizing bacteria (AOB) and ammonia-oxidizing archaea (AOA) in temperate forest soils at Coweeta Hydrologic...

Aluminium or copper substrate panel for selective absorption of solar energy

NASA Technical Reports Server (NTRS)

Roberts, M. L.; Sharpe, M. H.; Krupnick, A. C. (Inventor)

1979-01-01

A method for making panels which selectively absorb solar energy is disclosed. The panels are comprised of an aluminum substrate, a layer of zinc thereon, a layer of nickel over the zinc layer and an outer layer of solar energy absorbing nickel oxide or a copper substrate with a layer of nickel thereon and a layer of solar energy absorbing nickel oxide distal from the copper substrate.

Method for making an aluminum or copper substrate panel for selective absorption of solar energy

NASA Technical Reports Server (NTRS)

Roberts, M. L.; Sharpe, M. H.; Krupnick, A. C. (Inventor)

1978-01-01

A panel is described for selectively absorbing solar energy comprising an aluminum substrate. A zinc layer was covered by a layer of nickel and an outer layer of solar energy absorbing nickel oxide or a copper substrate with a nickel layer. A layer of solar energy absorbing nickel oxide distal from the copper substrate was included. A method for making these panels is disclosed.

Respective effects of oxygen and energy substrate deprivation on beta cell viability.

PubMed

Lablanche, Sandrine; Cottet-Rousselle, Cécile; Argaud, Laurent; Laporte, Camille; Lamarche, Frédéric; Richard, Marie-Jeanne; Berney, Thierry; Benhamou, Pierre-Yves; Fontaine, Eric

2015-01-01

Deficit in oxygen and energetic substrates delivery is a key factor in islet loss during islet transplantation. Permeability transition pore (PTP) is a mitochondrial channel involved in cell death. We have studied the respective effects of oxygen and energy substrate deprivation on beta cell viability as well as the involvement of oxidative stress and PTP opening. Energy substrate deprivation for 1h followed by incubation in normal conditions led to a cyclosporin A (CsA)-sensitive-PTP-opening in INS-1 cells and human islets. Such a procedure dramatically decreased INS-1 cells viability except when transient removal of energy substrates was performed in anoxia, in the presence of antioxidant N-acetylcysteine (NAC) or when CsA or metformin inhibited PTP opening. Superoxide production increased during removal of energy substrates and increased again when normal energy substrates were restored. NAC, anoxia or metformin prevented the two phases of oxidative stress while CsA prevented the second one only. Hypoxia or anoxia alone did not induce oxidative stress, PTP opening or cell death. In conclusion, energy substrate deprivation leads to an oxidative stress followed by PTP opening, triggering beta cell death. Pharmacological prevention of PTP opening during islet transplantation may be a suitable option to improve islet survival and graft success. Copyright © 2015 Elsevier B.V. All rights reserved.

Biocatalytic oxidation by chloroperoxidase from Caldariomyces fumago in polymersome nanoreactors.

PubMed

de Hoog, H M; Nallani, M; Cornelissen, J J L M; Rowan, A E; Nolte, R J M; Arends, I W C E

2009-11-21

The encapsulation of chloroperoxidase from Caldariomyces fumago (CPO) in block copolymer polymersomes is reported. Fluorescence and electron microscopy show that when the encapsulating conditions favour self-assembly of the block copolymer, the enzyme is incorporated with concentrations that are 50 times higher than the enzyme concentration before encapsulation. The oxidation of two substrates by the encapsulated enzyme was studied: i) pyrogallol, a common substrate used to assay CPO enzymatic activity and ii) thioanisole, of which the product, (R)-methyl phenyl sulfoxide, is an important pharmaceutical intermediate. The CPO-loaded polymersomes showed distinct reactivity towards these substrates. While the oxidation of pyrogallol was limited by diffusion of the substrate into the polymersome, the rate-limiting step for the oxidation of thioansiole was the turnover by the enzyme.

Data on the effect of improved TiO2/FTO interface and Ni(OH)2 cocatalyst on the photoelectrochemical performances and stability of CdS cased ZnIn2S4/TiO2 heterojunction.

PubMed

Mahadik, Mahadeo A; Shinde, Pravin S; Lee, Hyun Hwi; Cho, Min; Jang, Jum Suk

2018-04-01

This data article presents the experimental evidences of the effect of TiO 2 -fluorine doped tin oxide interface annealing and Ni(OH) 2 cocatalysts on the photoelectrochemical, structural, morphological and optical properties of Ni(OH) 2 /CdS/ZnIn 2 S 4 /TiO 2 heterojunction. The Raman spectroscopy exhibits the sharp features of the rutile phase of TiO 2 and in agreement with the X-ray diffraction data. The band gap energy of the 500 °C sample was found to be 3.12 eV, further it was increased to 3.20, 3.22 eV for samples annealed at 600 and 700 °C respectively. The decrease in the band gap energy at 500 °C related to the oxygen vacancies and was analysed by photoluminescence spectroscopy analysis. The synthesis, characterization methods and other experimental details of TiO 2 based heterostructure are also provided. The presence of CdS and ZnIn 2 S 4 coating on surface of TiO 2 electrodes providing a high surface area, extended visible absorption and helps to improve the change separation. This data article contains data related to the research article entitled "Highly efficient and stable 3D Ni(OH) 2 /CdS/ZnIn 2 S 4 /TiO 2 heterojunction under solar light: Effect of an improved TiO 2 /FTO interface and cocatalyst" (Mahadik et al., 2017) [1].

Tyrosinase kinetics: failure of acceleration in oxidation of ring-blocked monohydric phenol substrate.

PubMed

Naish-Byfield, S; Riley, P A

1998-04-01

When 2,5,6-trimethyl-4-hydroxyanisole is used as substrate for mushroom tyrosinase the oxidation rate is slow and the kinetics do not exhibit an initial acceleration (lag period), in contrast to the kinetics of oxidation of the parent compound, 4-hydroxyanisole. This finding is interpreted as evidence that the acceleration of oxidation of 4-hydroxyanisole is indirectly contingent on a reductive nucleophile addition to the orthoquinone product of the monohydric phenol, which is prevented by ring methylation. Such a view is consistent with the proposal that the lag-phase characteristic of the kinetics of monohydric phenol oxidation by tyrosinase is due to the activation of previously inactive enzyme by electron donation from an orthodiphenol substrate formed from the orthoquinone oxidation product.

Electro-deposition of superconductor oxide films

DOEpatents

Bhattacharya, Raghu N.

2001-01-01

Methods for preparing high quality superconducting oxide precursors which are well suited for further oxidation and annealing to form superconducting oxide films. The method comprises forming a multilayered superconducting precursor on a substrate by providing an electrodeposition bath comprising an electrolyte medium and a substrate electrode, and providing to the bath a plurality of precursor metal salts which are capable of exhibiting superconducting properties upon subsequent treatment. The superconducting precursor is then formed by electrodepositing a first electrodeposited (ED) layer onto the substrate electrode, followed by depositing a layer of silver onto the first electrodeposited (ED) layer, and then electrodepositing a second electrodeposited (ED) layer onto the Ag layer. The multilayered superconducting precursor is suitable for oxidation at a sufficient annealing temperature in air or an oxygen-containing atmosphere to form a crystalline superconducting oxide film.

Decal transfer microfabrication

DOEpatents

Nuzzo, Ralph G.; Childs, William Robert

2004-10-19

A method of making a microstructure includes forming a pattern in a surface of a silicon-containing elastomer, oxidizing the pattern, contacting the pattern with a substrate; and bonding the oxidized pattern and the substrate such that the pattern and the substrate are irreversibly attached. The silicon-containing elastomer may be removably attached to a transfer pad.

Structure having spatially separated photo-excitable electron-hole pairs and method of manufacturing same

DOEpatents

Liang, Yong [Richland, WA; Daschbach, John L [Richland, WA; Su, Yali [Richland, WA; Chambers, Scott A [Kennewick, WA

2006-08-22

A method for producing quantum dots. The method includes cleaning an oxide substrate and separately cleaning a metal source. The substrate is then heated and exposed to the source in an oxygen environment. This causes metal oxide quantum dots to form on the surface of the substrate.

Structure having spatially separated photo-excitable electron-hole pairs and method of manufacturing same

DOEpatents

Liang, Yong [Richland, WA; Daschbach, John L [Richland, WA; Su, Yali [Richland, WA; Chambers, Scott A [Kennewick, WA

2003-03-18

A method for producing quantum dots. The method includes cleaning an oxide substrate and separately cleaning a metal source. The substrate is then heated and exposed to the source in an oxygen environment. This causes metal oxide quantum dots to form on the surface of the substrate.

Cyclic Oxidation Behavior of Cold Sprayed CuCrAl-Coated and Uncoated GRCop-84 Substrates for Space Launch Vehicles

NASA Technical Reports Server (NTRS)

Raj, S. V.; Barrett, C.; Karthikeyan, J.; Garlick, R.

2006-01-01

A newly developed Cu-23 (wt %) Cr-5%Al (CuCrAl) alloy shown to resist hydridation and oxidation in an as-cast form is currently being considered as a protective coating for GRCop-84, which is an advanced copper alloy containing 8 (at.%) Cr and 4 (at.%) Nb. The coating was deposited on GRCop-84 substrates by the cold spray deposition technique. Cyclic oxidation tests conducted in air on both coated and uncoated substrates between 773 and 1073 K revealed that the coating remained intact and protected the substrate up to 1073 K. No significant weight loss of the coated specimens were observed at 773 and 873 K even after a cumulative cyclic time of 500 h. About a 10 percent weight loss observed at 973 and 1073 K was attributed to the excessive oxidation of the uncoated sides. In contrast, the uncoated substrate lost as much as 80 percent of its original weight under similar test conditions. It is concluded that the cold sprayed CuCrAl coating is suitable for protecting GRCop-84 substrates.

The Integration of Nanoscale Techniques for an Improved Battery Technology

DTIC Science & Technology

2012-06-08

anodized aluminum oxide ( AAO ) membranes that were 13...nanoporous anodized aluminum oxide ( AAO ) substrate [13]. During sputtering, thickened columnar growths form around the pores of the substrate...investigates an interpenetrating network structure where ―tubes‖ of polymer electrolyte are placed in the nanopores of anodic aluminum oxide ( AAO

Structural characterizations of pure SnS and In-doped SnS thin films using isotropic and anisotropic models

NASA Astrophysics Data System (ADS)

Kafashan, Hosein

2018-04-01

An electrochemical route has been employed to prepare pure SnS and indium-doped SnS thin films. Six samples including undoped SnS and In-doped SnS thin films deposited on the fluorine-doped tin oxide (FTO) glass substrates. An aqueous solution having SnCl2 and Na2S2O3 used as the primary electrolyte. Different In-doped SnS samples were prepared by adding a different amount of 1 mM InCl3 solution into the first electrolyte. The applied potential (E), time of deposition (t), pH and bath temperature (T) were kept at ‑1 V, 30 min, 2.1 and 60 °C, respectively. For all samples, except the In-dopant concentration, all the deposition parameters are the same. After preparation, X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) with an energy dispersive X-ray analyzer (EDX) attachment, atomic force microscopy (AFM), and transmission electron microscopy (TEM) were used to determine structural properties of as-deposited films. XRD patterns revealed that the synthesized undoped- and In-doped SnS thin films were crystallized in the orthorhombic structure. The shape of SnS crystals was spherical in the TEM image. X-ray peak broadening studies was done by applying Scherrer’s method, Williamson-Hall (W–H) models (including uniform deformation model (UDM), uniform strain deformation model (UDSM), and uniform deformation energy density model (UDEDM)), and size-strain plot (SSP) method. Using these techniques, the crystallite size and the lattice strains have been predicted. There was a good agreement in the particle size achieved by W–H- and SSP methods with TEM image.

Enhanced photovoltaic performance utilizing effective charge transfers and light scattering effects by the combination of mesoporous, hollow 3D-ZnO along with 1D-ZnO in CdS quantum dot sensitized solar cells.

PubMed

Chetia, Tridip Ranjan; Barpuzary, Dipankar; Qureshi, Mohammad

2014-05-28

A combination of 3-dimensional (3D) hollow mesoporous ZnO microspheres (ZnO HMSP) and vertically grown one-dimensional ZnO nanowires (1D ZnO NWs) on a fluorine doped tin oxide (FTO) coated glass substrate has been investigated as a photoanode for a CdS quantum dot-sensitized solar cell (QSSC). A comparative study of the photovoltaic performance of the solar cell with devices fabricated with pristine ZnO HMSPs and ZnO NWs was carried out. The proposed photovoltaic device exhibits an enhancement in power conversion efficiency (PCE) upto ∼74% and ∼35%, as compared to the 1D ZnO NW and ZnO HMSP based solar cells. The maximum incident photon-to-current conversion efficiency (IPCE) for the solar cell was observed to be ∼40%, whereas for the devices fabricated with bare ZnO HMSP and ZnO NW the IPCE were only ∼32% and ∼19%, respectively. The enhanced photovoltaic performance of the solar cell is attributed to the high Brunauer-Emmett-Teller (BET) surface area, efficient light-scattering effects and facilitated diffusion of the electrolyte for better functioning of the redox couple (S(2-)/Sn(2-)) in the hybrid photoanode. Moreover, a faster electron transport through 1D ZnO NWs provides better charge collection from the photoactive layer, which leads to an increase in the short circuit current density of the device. The present study highlights the design and development of a new hybrid photoanode for solar harvesting.

Method of making a hydrogen transport membrane, and article

DOEpatents

Schwartz, Joseph M.; Corpus, Joseph M.; Lim, Hankwon

2015-07-21

The present invention relates to a method of manufacturing a hydrogen transport membrane and the composite article itself. More specifically, the invention relates to producing a membrane substrate, wherein the ceramic substrate is coated with a metal oxide slurry, thereby eliminating the need for an activation step prior to plating the ceramic membrane through an electroless plating process. The invention also relates to modifying the pore size and porosity of the substrate by oxidation or reduction of the particles deposited by the metal oxide slurry.

Self-Supported Copper Oxide Electrocatalyst for Water Oxidation at Low Overpotential and Confirmation of Its Robustness by Cu K-edge X-ray Absorption Spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Xiang; Cui, Shengsheng; Sun, Zijun

Developing efficient water oxidation catalysts made of earth-abundant elements is a demanding challenge that should be met to fulfill the promise of water splitting for clean energy. Herein we report an annealing approach to synthesize binder-free, self-supported heterogeneous copper oxide (CuO) on conductive electrodes for oxygen evolution reaction (OER), producing electrodes with excellent electrocatalytic properties such as high efficiency, low overpotential, and good stability. The catalysts were grown in situ on fluorine-doped tin oxide (FTO) by electrodeposition from a simple Cu(II) salt solution, followed by annealing at a high temperature. Under optimal conditions, the CuO-based OER catalyst shows an onsetmore » potential of <0.58 V (vs Ag/AgCl) in 1.0 M KOH at pH 13.6. From the Tafel plot, the required overpotentials for current densities of 0.1 and 1.0 mA/cm2 are only 360 and 430 mV, respectively. The structure and the presence of a CuO motif in the catalyst have been identified by high-energy X-ray diffraction (HE-XRD), Cu K-edge X-ray absorption (XAS) spectra including X-ray absorption near-edge structure (XANES), and extended X-ray absorption fine structure (EXAFS). To the best of our knowledge, this represents the best catalytic activity for CuO-based OER catalysts to date.« less

Cyclic oxidation behavior of plasma sprayed NiCrAlY/WC-Co/cenosphere coating

NASA Astrophysics Data System (ADS)

Mathapati, Mahantayya; Ramesh M., R.; Doddamani, Mrityunjay

2018-04-01

Components working at elevated temperature like boiler tubes of coal and gas fired power generation plants, blades of gas and steam turbines etc. experience degradation owing to oxidation. Oxidation resistance of such components can be increased by developing protective coatings. In the present investigation NiCrAlY-WC-Co/Cenosphere coating is deposited on MDN 321 steel substrate using plasma spray coating. Thermo cyclic oxidation behavior of coating and substrate is studied in static air at 600 °C for 20 cycles. The thermo gravimetric technique is used to approximate the kinetics of oxidation. X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and X-ray mapping techniques are used to characterize the oxidized samples. NiCrAlY-WC-Co/Cenosphere coating exhibited lower oxidation rate in comparison to MDN 321 steel substrate. The lower oxidation rate of coating is attributed to formation of Al2O3, Cr2O3, NiO and CoWO4 oxides on the outermost surface.

Substrate-dependent temperature sensitivity of soil organic matter decomposition

NASA Astrophysics Data System (ADS)

Myachina, Olga; Blagodatskaya, Evgenia

2015-04-01

Activity of extracellular enzymes responsible for decomposition of organics is substrate dependent. Quantity of the substrate is the main limiting factor for enzymatic or microbial heterotrophic activity in soils. Different mechanisms of enzymes response to temperature suggested for low and high substrate availability were never proved for real soil conditions. We compared the temperature responses of enzymes-catalyzed reactions in soils. Basing on Michaelis-Menten kinetics we determined the enzymes affinity to substrate (Km) and mineralization potential of heterotrophic microorganisms (Vmax) 1) for three hydrolytic enzymes: β-1,4-glucosidase, N-acetyl- β -D-glucosaminidase and phosphatase by the application of fluorogenically labeled substrates and 2) for mineralization of 14C-labeled glucose by substrate-dependent respiratory response. Here we show that the amount of available substrate is responsible for temperature sensitivity of hydrolysis of polymers in soil, whereas monomers oxidation to CO2 does not depend on substrate amount and is mainly temperature governed. We also found that substrate affinity of enzymes (which is usually decreases with the temperature) differently responded to warming for the process of depolymerisation versus monomers oxidation. We suggest the mechanism to temperature acclimation based on different temperature sensitivity of enzymes kinetics for hydrolysis of polymers and for monomers oxidation.

Environmentally-assisted technique for transferring devices onto non-conventional substrates

DOEpatents

Lee, Chi-Hwan; Kim, Dong Rip; Zheng, Xiaolin

2016-05-10

A device fabrication method includes: (1) providing a growth substrate including an oxide layer; (2) forming a metal layer over the oxide layer; (3) forming a stack of device layers over the metal layer; (4) performing fluid-assisted interfacial debonding of the metal layer to separate the stack of device layers and the metal layer from the growth substrate; and (5) affixing the stack of device layers to a target substrate.

Epitaxial growth of CZT(S,Se) on silicon

DOEpatents

Bojarczuk, Nestor A.; Gershon, Talia S.; Guha, Supratik; Shin, Byungha; Zhu, Yu

2016-03-15

Techniques for epitaxial growth of CZT(S,Se) materials on Si are provided. In one aspect, a method of forming an epitaxial kesterite material is provided which includes the steps of: selecting a Si substrate based on a crystallographic orientation of the Si substrate; forming an epitaxial oxide interlayer on the Si substrate to enhance wettability of the epitaxial kesterite material on the Si substrate, wherein the epitaxial oxide interlayer is formed from a material that is lattice-matched to Si; and forming the epitaxial kesterite material on a side of the epitaxial oxide interlayer opposite the Si substrate, wherein the epitaxial kesterite material includes Cu, Zn, Sn, and at least one of S and Se, and wherein a crystallographic orientation of the epitaxial kesterite material is based on the crystallographic orientation of the Si substrate. A method of forming an epitaxial kesterite-based photovoltaic device and an epitaxial kesterite-based device are also provided.