Sample records for package astm type

  1. Fuel and Fuel System Materials Compatibility Test Program for A JP-8+100 Fuel Additive. Volume 1: Thermal Stability Additive Package BetzDearborn Spec Aid(Registered) 8Q462

    DTIC Science & Technology

    2001-10-01

    SAE Rings, Sealing, Butadiene-Acrylonitrile ( NBR ), Rubber Fuel and Low Temperature Resistant 60 - 70 MIL-R-83248C Rubber , Fluorocarbon...KAPTON/TEFLON (COMPOSITE) WIRE I.I.10 34 VI. REFERENCE DOCUMENTS Non-Metallics MIL-HDBK-149B Military Standardization Hand Book Rubber ...ASTM D-1414 Standard Test Methods for Rubber O-Rings ASTM D-412 Type II Standard Test Methods for Vulcanized Rubber and Thermoplastic

  2. 49 CFR 179.300-7 - Materials.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... carbon steel must not exceed 0.31 percent, although the individual ASTM specification may allow for a... (longitudinal) (minimum) ASTM A 240/A 240M type 304 75,000 25 ASTM A 240/A 240M type 304L 70,000 25 ASTM A 240/A 240M type 316 75,000 25 ASTM A 240/A 240M type 316L 70,000 25 ASTM A 240/A 240M type 321 75,000 25 ASTM...

  3. Vacuum decay container/closure integrity testing technology. Part 1. ASTM F2338-09 precision and bias studies.

    PubMed

    Wolf, Heinz; Stauffer, Tony; Chen, Shu-Chen Y; Lee, Yoojin; Forster, Ronald; Ludzinski, Miron; Kamat, Madhav; Godorov, Phillip; Guazzo, Dana Morton

    2009-01-01

    ASTM F2338-09 Standard Test Method for Nondestructive Detection of Leaks in Packages by Vacuum Decay Method is applicable for leak-testing rigid and semi-rigid non-lidded trays; trays or cups sealed with porous barrier lidding materials; rigid, nonporous packages; and flexible, nonporous packages. Part 1 of this series describes the precision and bias studies performed in 2008 to expand this method's scope to include rigid, nonporous packages completely or partially filled with liquid. Round robin tests using three VeriPac 325/LV vacuum decay leak testers (Packaging Technologies & Inspection, LLC, Tuckahoe, NY) were performed at three test sites. Test packages were 1-mL glass syringes. Positive controls had laser-drilled holes in the barrel ranging from about 5 to 15 microm in nominal diameter. Two different leak tests methods were performed at each site: a "gas leak test" performed at 250 mbar (absolute) and a "liquid leak test" performed at about 1 mbar (absolute). The gas leak test was used to test empty, air-filled syringes. All defects with holes > or = 5.0 microm and all no-defect controls were correctly identified. The only false negative result was attributed to a single syringe with a < 5.0-microm hole. Tests performed using a calibrated air leak supported a 0.10-cm3 x min(-1) (ccm) sensitivity limit (99/99 lower tolerance limit). The liquid leak test was used to test both empty, air-filled syringes and water-filled syringes. Test results were 100% accurate for all empty and water-filled syringes, both without holes and with holes (5, 10, and 15 microm). Tests performed using calibrated air flow leaks of 0, 0.05, and 0.10 ccm were also 100% accurate; data supported a 0.10-ccm sensitivity limit (99/99 lower tolerance limit). Quantitative differential pressure results strongly correlated to hole size using either liquid or gas vacuum decay leak tests. The higher vacuum liquid leak test gave noticeably higher pressure readings when water was present in the defect. Both the ASTM F2338-09 test method and the precision and bias study report are available by contacting ASTM International in West Conshohocken, PA, USA (www.astm.org).

  4. Polyhydroxyalkanoates (PHA) Bioplastic Packaging Materials

    DTIC Science & Technology

    2010-05-01

    FINAL REPORT Polyhydroxyalkanoates (PHA) Bioplastic Packaging Materials SERDP Project WP-1478 MAY 2010 Dr.Chris Schwier Metabolix...biopolymer, biodegradable, polyhydroxyalkanoate 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT 18. NUMBER OF PAGES 19a. NAME OF...Acronyms and Definitions ASTM – American Society of Test Methods ISO – International Standardization Organization PHA – Polyhydroxyalkanoates

  5. Microbial ranking of porous packaging materials (exposure chamber method), ASTM method: collaborative study.

    PubMed

    Placencia, A M; Peeler, J T

    1999-01-01

    A collaborative study involving 11 laboratories was conducted to measure the microbial barrier effectiveness of porous medical packaging. Two randomly cut samples from each of 6 commercially available porous materials and one positive and one negative control were tested by one operator in each of 11 laboratories. Microbial barrier effectiveness was measured in terms of logarithm reduction value (LRV), which reflects the log10 microbial penetration of the material being tested. The logarithm of the final concentration is subtracted from that of the initial concentration to obtain the LRV. Thus the higher the LRV, the better the barrier. Repeatability standard deviations ranged from 6.42 to 16.40; reproducibility standard deviations ranged from 15.50 to 22.70. Materials B(53), C(50), D(CT), and E(45MF) differ significantly from the positive control. The microbial ranking of porous packaging materials (exposure chamber method), ASTM method, has been adopted First Action by AOAC INTERNATIONAL.

  6. VIBRATION TESTING OF RESILIENT PACKAGE CUSHIONING MATERIALS

    DTIC Science & Technology

    government and industry. Testing equipment which meets tentative ASTM requirements was developed. Preliminary tests were conducted on a resilient expanded ... polystyrene foam (in 3 densities) and a polyether urethane foam (in one density). When vibrated under static loads known to provide optimum shock

  7. 46 CFR 160.133-7 - Design, construction, and performance of release mechanisms.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... be a type 302 stainless steel per ASTM A 276, ASTM A 313 or ASTM A 314 (incorporated by reference... fifth percentile female to the ninety-fifth percentile male values for critical body dimensions and... correspond to the arctic clothed dimensions of ASTM F 1166; (3) Steel. Each major structural component of...

  8. Corrosion Susceptibility of AA5083-H116 in Biologically Active Atmospheric Marine Environments

    DTIC Science & Technology

    2014-03-01

    by the standardized nitric acid test ASTM G67." Fatigue and stress corrosion cracking behaviors of sensitized AA5083 have also been evaluated.1213... acid (NAMLT Test)," ASTM Hanbook 3.02 Corrosion of Metals; Wear and Erosion. ASTM Hanbook 3.02 Corrosion of Metals; Wear and Erosion (ASTM...DATE (DD-MM-YYYY) 12-05-2014 REPORT TYPE Conference Proceeding (refereed) 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Corrosion

  9. Vacuum decay container closure integrity leak test method development and validation for a lyophilized product-package system.

    PubMed

    Patel, Jayshree; Mulhall, Brian; Wolf, Heinz; Klohr, Steven; Guazzo, Dana Morton

    2011-01-01

    A leak test performed according to ASTM F2338-09 Standard Test Method for Nondestructive Detection of Leaks in Packages by Vacuum Decay Method was developed and validated for container-closure integrity verification of a lyophilized product in a parenteral vial package system. This nondestructive leak test method is intended for use in manufacturing as an in-process package integrity check, and for testing product stored on stability in lieu of sterility tests. Method development and optimization challenge studies incorporated artificially defective packages representing a range of glass vial wall and sealing surface defects, as well as various elastomeric stopper defects. Method validation required 3 days of random-order replicate testing of a test sample population of negative-control, no-defect packages and positive-control, with-defect packages. Positive-control packages were prepared using vials each with a single hole laser-drilled through the glass vial wall. Hole creation and hole size certification was performed by Lenox Laser. Validation study results successfully demonstrated the vacuum decay leak test method's ability to accurately and reliably detect those packages with laser-drilled holes greater than or equal to approximately 5 μm in nominal diameter. All development and validation studies were performed at Whitehouse Analytical Laboratories in Whitehouse, NJ, under the direction of consultant Dana Guazzo of RxPax, LLC, using a VeriPac 455 Micro Leak Test System by Packaging Technologies & Inspection (Tuckahoe, NY). Bristol Myers Squibb (New Brunswick, NJ) fully subsidized all work. A leak test performed according to ASTM F2338-09 Standard Test Method for Nondestructive Detection of Leaks in Packages by Vacuum Decay Method was developed and validated to detect defects in stoppered vial packages containing lyophilized product for injection. This nondestructive leak test method is intended for use in manufacturing as an in-process package integrity check, and for testing product stored on stability in lieu of sterility tests. Test method validation study results proved the method capable of detecting holes laser-drilled through the glass vial wall greater than or equal to 5 μm in nominal diameter. Total test time is less than 1 min per package. All method development and validation studies were performed at Whitehouse Analytical Laboratories in Whitehouse, NJ, under the direction of consultant Dana Guazzo of RxPax, LLC, using a VeriPac 455 Micro Leak Test System by Packaging Technologies & Inspection (Tuckahoe, NY). Bristol Myers Squibb (New Brunswick, NJ) fully subsidized all work.

  10. 40 CFR 796.3500 - Hydrolysis as a function of pH at 25 °C.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... biodegradation. ASTM Type IIA water is described in ASTM D 1193-77 (Reapproved 1983), “Standard Specification for... solutions and in carrying out all hydrolysis experiments to eliminate or minimize biodegradation. Glassware...

  11. 40 CFR 796.3500 - Hydrolysis as a function of pH at 25 °C.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... biodegradation. ASTM Type IIA water is described in ASTM D 1193-77 (Reapproved 1983), “Standard Specification for... carrying out all hydrolysis experiments to eliminate or minimize biodegradation. Glassware can be...

  12. 40 CFR 796.3500 - Hydrolysis as a function of pH at 25 °C.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... biodegradation. ASTM Type IIA water is described in ASTM D 1193-77 (Reapproved 1983), “Standard Specification for... carrying out all hydrolysis experiments to eliminate or minimize biodegradation. Glassware can be...

  13. 40 CFR 796.3500 - Hydrolysis as a function of pH at 25 °C.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... equivalent grade) shall be used to minimize biodegradation. ASTM Type IIA water is described in ASTM D 1193... experiments to eliminate or minimize biodegradation. Glassware can be sterilized in an autoclave or by any...

  14. Formability of new high performance A710 grade 50 structural steel.

    DOT National Transportation Integrated Search

    2014-01-01

    This project compared the formability of modified ASTM A710 Grade B50 ksi yield strength steel, jointly developed by : Northwestern University and the Illinois Department of Transportation, with ASTM A606 Type 4 weathering steel used in Illinois : an...

  15. Filtration Effects Due to Bioassay Cage Design and Screen Type

    DTIC Science & Technology

    2010-01-01

    Optical Nonimaging Light- Scattering Instruments (ASTM, 2003). Droplet sizing data included volume median diam (DV50), and the 10% and 90% diam (DV10 and...optical nonimaging light-scattering instru- ments. In: Annual book of ASTM standards. West Conshohocken, PA: American Society for Testing and Materials

  16. Wetting properties of Au/Sn solders for microelectronics

    NASA Astrophysics Data System (ADS)

    Peterson, K. A.; Williams, C. B.

    Hermetic sealing of microelectronic packages with Au/Sn solder is critically dependent upon good wetting. In studying specific problems in hermetic sealing, a solderability test based on ASTM standard F-357-78 has proven useful. The test has helped isolate and quantify the effects of contamination due to epoxy die attach and related handling, thermal preconditioning of packages, gold plating thickness, time and temperature during sealing, and solder alloy composition as they affect wetting. Some differences in hardware have been documented between manufacturing lots, but the overriding factors have been contamination which occurs during packaging process flows and thermal preconditioning during processing. The paper includes a review of metallurgical aspects of soldering to a non-inert surface and an examination of microstructural differences in seal joints. The results also quantify the conventional wisdom that alloys which are on the tin-rich side of the eutectic composition offer superior wetting properties.

  17. Comparative field permeability measurement of permeable pavements using ASTM C1701 and NCAT permeameter methods.

    PubMed

    Li, Hui; Kayhanian, Masoud; Harvey, John T

    2013-03-30

    Fully permeable pavement is gradually gaining support as an alternative best management practice (BMP) for stormwater runoff management. As the use of these pavements increases, a definitive test method is needed to measure hydraulic performance and to evaluate clogging, both for performance studies and for assessment of permeability for construction quality assurance and maintenance needs assessment. Two of the most commonly used permeability measurement tests for porous asphalt and pervious concrete are the National Center for Asphalt Technology (NCAT) permeameter and ASTM C1701, respectively. This study was undertaken to compare measured values for both methods in the field on a variety of permeable pavements used in current practice. The field measurements were performed using six experimental section designs with different permeable pavement surface types including pervious concrete, porous asphalt and permeable interlocking concrete pavers. Multiple measurements were performed at five locations on each pavement test section. The results showed that: (i) silicone gel is a superior sealing material to prevent water leakage compared with conventional plumbing putty; (ii) both methods (NCAT and ASTM) can effectively be used to measure the permeability of all pavement types and the surface material type will not impact the measurement precision; (iii) the permeability values measured with the ASTM method were 50-90% (75% on average) lower than those measured with the NCAT method; (iv) the larger permeameter cylinder diameter used in the ASTM method improved the reliability and reduced the variability of the measured permeability. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. Chitosan coatings onto polyethylene terephthalate for the development of potential active packaging material

    NASA Astrophysics Data System (ADS)

    Zemljič, Lidija Fras; Tkavc, Tina; Vesel, Alenka; Šauperl, Olivera

    2013-01-01

    In this paper advanced surface treatment of PET plastic film is presented for introduction of antimicrobial properties as a potential application for food (as for example meat) packaging material. Adsorption/desorption of chitosan onto PET plastic film surface was studied using several analytical techniques such as: X-Ray Photoelectron Spectroscopy (XPS), ATR-FTIR spectroscopy and titrations. Kinetic desorption of chitosan from PET surface was analysed by polyelectrolyte titration and spectrophotometric Ninhydrine reaction. Standard antimicrobial test ASTM E2149-01 was performed for functionalised PET materials in order to determine their antimicrobial properties; i. e. to measure the reductions of some of the meat pathogens; such as bacteria Salmonella enterica, Campylobacter spp., Escherichia coli, Listeria monocytogenes and fungi Candida albicans.

  19. Comparison of attrition test methods: ASTM standard fluidized bed vs jet cup

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zhao, R.; Goodwin, J.G. Jr.; Jothimurugesan, K.

    2000-05-01

    Attrition resistance is one of the key design parameters for catalysts used in fluidized-bed and slurry phase types of reactors. The ASTM fluidized-bed test has been one of the most commonly used attrition resistance evaluation methods; however, it requires the use of 50 g samples--a large amount for catalyst development studies. Recently a test using the jet cup requiring only 5 g samples has been proposed. In the present study, two series of spray-dried iron catalysts were evaluated using both the ASTM fluidized-bed test and a test based on the jet cup to determine this comparability. It is shown thatmore » the two tests give comparable results. This paper, by reporting a comparison of the jet-cup test with the ASTM standard, provides a basis for utilizing the more efficient jet cup with confidence in catalyst attrition studies.« less

  20. 40 CFR Table 6 to Subpart Ddddd of... - Fuel Analysis Requirements

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... D6323-98 (2003) (for biomass) (IBR, See § 63.14(b)) or equivalent. b. Composite fuel samples... D5198-92 (2003) (for biomass) (IBR, see § 63.14(b)) or equivalent. d. Determine heat content of the fuel type * * * ASTM D5865-04 (for coal) (IBR, see § 63.24(b)) or ASTM E711-87 (for biomass) (IBR, see § 63...

  1. Electrochemical Testing of Ni-Cr-Mo-Gd Alloys

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    T. E. Lister; R. E. Mizia; H. Tian

    2005-10-01

    The waste package site recommendation design specified a boron-containing stainless steel, Neutronit 976/978, for fabrication of the internal baskets that will be used as a corrosion-resistant neutron-absorbing material. Recent corrosion test results gave higher-than-expected corrosion rates for this material. The material callout for these components has been changed to a Ni-Cr-Mo-Gd alloy (ASTM-B 932-04, UNS N06464) that is being developed at the Idaho National Laboratory. This report discusses the results of initial corrosion testing of this material in simulated in-package environments that could contact the fuel baskets after breach of the waste package outer barrier. The corrosion test matrix wasmore » executed using the potentiodynamic and potentiostatic electrochemical test techniques. The alloy performance shows low rates of general corrosion after initial removal of a gadolinium-rich second phase that intersects the surface. The high halide-containing test solutions exhibited greater tendencies toward initiation of crevice corrosion.« less

  2. Laboratory Characterization of Type N Mortar

    DTIC Science & Technology

    2009-03-01

    and test results are documented in Chapter 2. Comparative plots and anal- yses of the experimental results are presented in Chapter 3. A summary is...determinations are provided in Table 1. Measurements of posttest water content1 were conducted in accordance with procedures given in American Society for...Testing and Materials (ASTM) D 2216 (ASTM 2005d). Based on the appropriate values of posttest water content, wet density, and an assumed grain density

  3. Biomechanical and histological effects of augmented soft tissue mobilization therapy on achilles tendinopathy in a rabbit model.

    PubMed

    Imai, Kan; Ikoma, Kazuya; Chen, Qingshan; Zhao, Chunfeng; An, Kai-Nan; Gay, Ralph E

    2015-02-01

    Augmented soft tissue mobilization (ASTM) has been used to treat Achilles tendinopathy and is thought to promote collagen fiber realignment and hasten tendon regeneration. The objective of this study was to evaluate the biomechanical and histological effects of ASTM therapy on rabbit Achilles tendons after enzymatically induced injury. This study was a non-human bench controlled research study using a rabbit model. Both Achilles tendons of 12 rabbits were injected with collagenase to produce tendon injury simulating Achilles tendinopathy. One side was then randomly allocated to receive ASTM, while the other received no treatment (control). ASTM was performed on the Achilles tendon on postoperative days 21, 24, 28, 31, 35, and 38. Tendons were harvested 10 days after treatment and examined with dynamic viscoelasticity and light microscopy. Cross-sectional area in the treated tendons was significantly greater than in controls. Storage modulus tended to be lower in the treated tendons but elasticity was not significantly increased. Loss modulus was significantly lower in the treated tendons. There was no significant difference found in tangent delta (loss modulus/storage modulus). Microscopy of control tendons showed that the tendon fibers were wavy and type III collagen was well stained. The tendon fibers of the augmented soft tissue mobilization treated tendons were not wavy and type III collagen was not prevalent. Biomechanical and histological findings showed that the Achilles tendons treated with ASTM had better recovery of biomechanical function than did control tendons. Copyright © 2015 National University of Health Sciences. Published by Elsevier Inc. All rights reserved.

  4. 49 CFR 178.345-2 - Material and material thickness.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... authorized for cargo tanks “constructed in accordance with the ASME Code”, Section VIII. ASTM A 569 ASTM A 570 ASTM A 572 ASTM A 622 ASTM A 656 ASTM A 715 ASTM A 1008/ A 1008M, ASTM A 1011/A 1011M (2) Aluminum... ASTM specifications may be used for cargo tanks “constructed in accordance with the ASME Code”: ASTM B...

  5. Thermal performance characterization of residential wall systems using a calibrated hot box with airflow induced by differential pressures

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Jones, D.C.; Ober, D.G.; Goodrow, J.T.

    1995-09-01

    ASTM E 283 ad ASTM E 1424 in conjunction with ASTM C 976 were used to study the effect of airflow on thermal performance of the wall. A typical residential 2 {times} 4 stud wall was constructed and placed on top of a subfloor, making a 2.44 {times} 2.74 m (8 by 9 ft) test specimen. This base wall assembly was then covered with two types of XPS sheathing, various housewraps, a 15{number_sign} felt, and a polyethylene vapor retarder film in 40 different configurations and tested individually per ASTM E 283 and per ASTM C 976. For 24 of themore » 40 C 976 tests, a differential pressure was induced across the test wall as per and ASTM E 1424. Airflows ranged from undetectable airflow at 0 {center_dot} Pa {Delta}P to 1.63 L/s {center_dot} m{sup 2} for the base wall assembly alone. Difference in airflow resistance performance between the ASTM E 283 and ASTM E 1424 test methods were noted. Thermal testing results incorporating both ASTM C 976 and ASTM E 1424 for tests 1--28 produced apparent thermal conductances (C-values) in the range of 0.40 W/m{sup 2} {center_dot} K for a nondetectable airflow level to 1.81 W/m{sup 2} {center_dot} K for an airflow of 1.53 L/s {center_dot} m{sup 2} for the base wall assembly alone with a 20-Pa {Delta}P. The calculated C-value for this base wall assembly was 0.40 W/m{sup 2} {center_dot} K. Test results reveal that airflow rates as low as 0.2 L/s {center_dot} m{sup 2} could produce a 46% increase in apparent C-value. Similar thermal performance differences were revealed when thicker shiplap XPS sheathing was used. Tests were also conducted using an Air-Tight Drywall configuration showing the effect of wind washing on thermal performance. By sealing the gypsum drywall on the base wall assembly tested, the apparent C-value, when exposed to a 12.5 Pa wind pressure, was found to be equivalent to a base wall assembly configuration which allows 0.15 L/s {center_dot} m{sup 2} airflow to penetrate completely through.« less

  6. Cadmium (Tank) Electroplating Alternative

    DTIC Science & Technology

    2011-08-01

    ASTM F519 HE: 75% NFS 200 hrs HRE : 45% NFS 150 hrs Threshold limit greater than /equal to LHE Cd (AMS 2417G) ASETS Defense Focused Workshop (2011...Test Specimens  Reporting Sustained/Threshold load (%NFS), Time to failure. HRE Testing Cd Zn-Ni IVD Al LHE Cd Re-Embrittlement Test Fluids:  DI...Hydrogen Embrittlement/ HRE ASTM F519 A5, Type 1.a.1 Brush Plating ASETS Defense Focused Workshop (2011) Luzmarie G. Santiago Materials Engineer Naval Air

  7. SPF Full-scale emissions test method development status ...

    EPA Pesticide Factsheets

    This is a non-technical presentation that is intended to inform ASTM task group members about our intended approach to full-scale emissions testing that includes the application of spray foam in an environmental chamber. The presentation describes the approach to emissions characterization, types of measurement systems employed, and expected outcomes from the planned tests. Purpose of this presentation is to update the ASTM D22.05 work group regarding status of our full-scale emissions test method development.

  8. 78 FR 63164 - Certain Small Diameter Carbon and Alloy Seamless Standard, Line and Pressure Pipe From Romania...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-23

    ... American Society for Testing and Materials (ASTM) A- 53, ASTM A-106, ASTM A-333, ASTM A-334, ASTM A-335, ASTM A-589, ASTM A- 795, and the American Petroleum Institute (API) 5L specifications and meeting the... to the application of external heat. Seamless carbon steel pressure pipe meeting the ASTM A- 106...

  9. 47 CFR 90.379 - ASTM E2213-03 DSRC Standard (ASTM-DSRC Standard).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false ASTM E2213-03 DSRC Standard (ASTM-DSRC Standard... Communications Service (dsrcs) § 90.379 ASTM E2213-03 DSRC Standard (ASTM-DSRC Standard). Roadside Units... incorporated by reference: American Society for Testing and Materials (ASTM) E2213-03, “Standard Specification...

  10. 40 CFR 80.1468 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ....astm.org). (1) ASTM D 1250-08 (“ASTM D 1250”), Standard Guide for Use of the Petroleum Measurement Tables, Approved 2008; IBR approved for § 80.1426(f)(8)(ii)(B). (2) ASTM D 4442-07 (“ASTM D 4442... 2007; IBR approved for § 80.1426(f)(7)(v)(B). (3) ASTM D 4444-08 (“ASTM D 4444”), Standard Test Method...

  11. 78 FR 14836 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-07

    ... Production Act of 1993--ASTM International Standards Notice is hereby given that, on February 11, 2013... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

  12. 77 FR 34069 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-08

    ... Production Act of 1993--ASTM International Standards Notice is hereby given that, on May 11, 2012, pursuant... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

  13. 78 FR 64248 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-28

    ... Production Act of 1993--ASTM International Standards Notice is hereby given that, on September 16, 2013... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

  14. 78 FR 35646 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-13

    ... Production Act of 1993--ASTM International Standards Notice is hereby given that, on May 10, 2013, pursuant... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

  15. 77 FR 61786 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-11

    ... Production Act of 1993--ASTM International Standards Notice is hereby given that, on September 10, 2012... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

  16. 76 FR 34252 - Notice Pursuant to the National Cooperative Research and Production Act of 1993; ASTM...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-13

    ... Production Act of 1993; ASTM International Standards Notice is hereby given that, on May 11, 2011, pursuant... seq. (``the Act''), ASTM International Standards (``ASTM'') has filed written notifications.... Specifically, ASTM has provided an updated list of current, ongoing ASTM standards activities originating...

  17. 76 FR 12370 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-07

    ... Production Act of 1993--ASTM International Standards Notice is hereby given that, on February 4, 2011... seq. (``the Act''), ASTM International Standards (``ASTM'') has filed written notifications.... Specifically, ASTM has provided an updated list of current, ongoing ASTM standards activities originating...

  18. 78 FR 1884 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-09

    ... Production Act of 1993--ASTM International Standards Notice is hereby given that, on December 12, 2012... seq. (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

  19. 76 FR 63658 - Notice Pursuant to the National Cooperative Research and Production Act of 1993; ASTM International

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-13

    ... Production Act of 1993; ASTM International Notice is hereby given that, on August 31, 2011, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

  20. 75 FR 11196 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-10

    ... Production Act of 1993--ASTM International Notice is hereby given that, on February 16, 2010, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

  1. 77 FR 14046 - Amended Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-08

    ... Research and Production Act of 1993--ASTM International Standards Notice is hereby given that, on February..., 15 U.S.C. 4301 et seq. (``the Act''), ASTM International Standards (``ASTM'') has filed written... circumstances. Specifically, ASTM has provided an updated list of current, ongoing ASTM standards activities...

  2. 77 FR 1085 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-09

    ... Production Act of 1993--ASTM International Notice is hereby given that, on December 5, 2011, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between...

  3. 75 FR 65657 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-26

    ... Production Act of 1993--ASTM International Notice is hereby given that, on September 23, 2010, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the..., ASTM has provided an updated list of current, ongoing ASTM standards activities originating between May...

  4. Molding compound trends in a denser packaging world: Qualification tests and reliability concerns

    NASA Astrophysics Data System (ADS)

    Nguyen, L. T.; Lo, R. H. Y.; Chen, A. S.; Belani, J. G.

    1993-12-01

    Molding compound development has traditionally been driven by the memory market, then subsequent applications filter down to other IC technologies such as logic, analog, and ASIC. However, this strategy has changed lately with the introduction of thin packages such as PQFP & TSOP. Rather than targeting a compound for a family of IC such as DRAM or SRAM, compound development efforts are now focused at specific classes of packages. The configurations of these thin packages impose new functional requirements that need to be revisited to provide the optimized combination of properties. The evolution of qualification tests mirrors the advances in epoxy and compounding technologies. From the first standard novolac-based epoxies of the 1970s to the latest 3(sup rd)-generation ultra-low stress materials, longer test times at increasingly harsher environments were achieved. This paper benchmarks the current reliability tests used by the electronic industry, examines those tests that affect and are affected by the molding compounds, discusses the relevance of accelerated testing, and addresses the major reliability issues facing current molding compound development efforts. Six compound-related reliability concerns were selected: moldability, package stresses, package cracking, halogen-induced intermetallic growth at bond pads, moisture-induced corrosion, and interfacial delamination. Causes of each failure type are surveyed and remedies are recommended. Accelerated tests are designed to apply to a limited quantity of devices, bias, or environmental conditions larger than usual ratings, to intensify failure mechanisms that would occur under normal operating conditions. The observed behavior is then extrapolated from the lot to the entire population. Emphasis is on compressing the time necessary to obtain reliability data. This approach has two main drawbacks. With increasingly complex devices, even accelerated tests are expensive. And with new technologies, it becomes difficult to ascertain that the applied stress 1) induces the failure phenomenon linked with usual field conditions, and 2) does not create any new ones. Technology evolution and reliability testing are interdependent. Devices get larger with increasingly smaller features and more complex geometries. Molding compounds have evolved considerably over the past decade to provide ultra-low stress levels and moldability for thin packages.

  5. 40 CFR Table 6 to Subpart Ddddd of... - Fuel Analysis Requirements

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... D2013/D2013M a (for coal), ASTM D5198 a (for biomass), or EPA 3050 a (for solid fuel), or EPA 821-R-01... (for coal) or ASTM E711 a (for biomass), or ASTM D5864 a for liquids and other solids, or ASTM D240 a... D2234/D2234M a (for coal) or ASTM D6323 a (for coal or biomass), ASTM D4177 a (for liquid fuels) or ASTM...

  6. 40 CFR Table 6 to Subpart Ddddd of... - Fuel Analysis Requirements

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... D2013/D2013M a (for coal), ASTM D5198 a (for biomass), or EPA 3050 a (for solid fuel), or EPA 821-R-01... (for coal) or ASTM E711 a (for biomass), or ASTM D5864 a for liquids and other solids, or ASTM D240 a... D2234/D2234M a (for coal) or ASTM D6323 a (for coal or biomass), ASTM D4177 a (for liquid fuels) or ASTM...

  7. Sterility and Safety Validation for Transport Packaging of Organs and Tissues.

    PubMed

    Cobos, M; Trunzo, L; Vogt, M V; Romero, O; Anessi, C; Pachado, J; Ciávaro, M N; Horak, C; Bacqué, M C

    2018-03-01

    The bags used in the transport of organs and tissues must be sterile, nontoxic, pyrogen free, and must serve as a barrier throughout their useful life. The goal of this study was to show the sterility, safety, and functionality of the bags subjected to irradiation, through validated procedures and techniques. The selected sterilization method was the use of gamma radiation. The sterilization dose was determined based on validated standards for the sterilization of medical products, ISO 11137-2: 2013 and ISO/TS 13004: 2013, using the Verification Dose Maximum method on samples belonging to 3 manufacturing lots. The ISO 10993-5: 2009 standard was used in the cytotoxicity tests, by means of extracts test and quantitative technique of MTT, 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide. The tests to determine the expiration date of the kit were performed by ASTM F1980, accelerated aging, and ASTM D3078 to evaluate hermeticity. The irradiation dose validated to reach the required sterility safety level was 22.5 kGy. The constituent materials and the sterilization method do not generated cellular toxicity, and the product was not modified during the simulated time of 5 years. Sterilization by irradiation is a method that leaves no residue, does not harm the properties of the material because it is conducted in cold, and as the sterilizing agent, the energy absorbed by the product is highly penetrating and can be treated in its final packaging, with no risk of postcontamination. It is for this reason that it is prioritized over other methods of sterilization. Copyright © 2017 Elsevier Inc. All rights reserved.

  8. Assessment of ASTM D 6690-12 type II and type IV joint sealers.

    DOT National Transportation Integrated Search

    2014-11-01

    To address the issue of water infiltration and debris retention, bi : tuminous crack sealers and fillers have been : developed to help prevent premature pavement distress. If applied appropriately, crack sealers and fillers can : significantly extend...

  9. 40 CFR 86.513-2004 - Fuel and engine lubricant specifications.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... ASTM D 86-97 23.9—35.0 1 2. 10% point, °C ASTM D 86-97 48.9—57.2 3. 50% point, °C ASTM D 86-97 93.3—110.0 4. 90% point, °C ASTM D 86-97 148.9—162.8 5. End point, °C ASTM D 86-97 212.8 Hydrocarbon composition: 1. Olefins, volume % ASTM D 1319-98 10 maximum 2. Aromatics, volume % ASTM D 1319-98 35 maximum 3...

  10. 49 CFR 192.113 - Longitudinal joint factor (E) for steel pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... class Longitudinal joint factor (E) ASTM A 53/A53M Seamless 1.00 Electric resistance welded 1.00 Furnace butt welded .60 ASTM A 106 Seamless 1.00 ASTM A 333/A 333M Seamless 1.00 Electric resistance welded 1.00 ASTM A 381 Double submerged arc welded 1.00 ASTM A 671 Electric-fusion-welded 1.00 ASTM A 672...

  11. 49 CFR 224.5 - Definitions.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., as where a layer of paint or dense chemical residue blocks all incoming light); this term does not... of American Railroads. Unqualified Retroreflective Sheeting means engineering grade sheeting, super engineering grade sheeting (enclosed lens) or high-intensity type sheeting (ASTM Type I, II, III, or IV...

  12. 40 CFR 799.5085 - Chemical testing requirements for first group of high production volume chemicals (HPV1).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    .... Acute Toxicity to Daphnia: ASTM E 729 3. Toxicity to Plants (Algae): ASTM E 1218 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193 2. Toxicity to Plants (Algae): ASTM E 1218 The following are the... conditions. Test Group 1 for C2: 1. Acute Toxicity to Daphnia: ASTM E 729 2. Toxicity to Plants (Algae): ASTM...

  13. 40 CFR 799.5085 - Chemical testing requirements for first group of high production volume chemicals (HPV1).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    .... Acute Toxicity to Daphnia: ASTM E 729 3. Toxicity to Plants (Algae): ASTM E 1218 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193 2. Toxicity to Plants (Algae): ASTM E 1218 The following are the... conditions. Test Group 1 for C2: 1. Acute Toxicity to Daphnia: ASTM E 729 2. Toxicity to Plants (Algae): ASTM...

  14. Vacuum decay container/closure integrity testing technology. Part 2. Comparison to dye ingress tests.

    PubMed

    Wolf, Heinz; Stauffer, Tony; Chen, Shu-Chen Y; Lee, Yoojin; Forster, Ronald; Ludzinski, Miron; Kamat, Madhav; Mulhall, Brian; Guazzo, Dana Morton

    2009-01-01

    Part 1 of this series demonstrated that a container closure integrity test performed according to ASTM F2338-09 Standard Test Method for Nondestructive Detection of Leaks in Packages by Vacuum Decay Method using a VeriPac 325/LV vacuum decay leak tester by Packaging Technologies & Inspection, LLC (PTI) is capable of detecting leaks > or = 5.0 microm (nominal diameter) in rigid, nonporous package systems, such as prefilled glass syringes. The current study compared USP, Ph.Eur. and ISO dye ingress integrity test methods to PTI's vacuum decay technology for the detection of these same 5-, 10-, and 15-microm laser-drilled hole defects in 1-mL glass prefilled syringes. The study was performed at three test sites using several inspectors and a variety of inspection conditions. No standard dye ingress method was found to reliably identify all holed syringes. Modifications to these standard dye tests' challenge conditions increased the potential for dye ingress, and adjustments to the visual inspection environment improved dye ingress detection. However, the risk of false positive test results with dye ingress tests remained. In contrast, the nondestructive vacuum decay leak test method reliably identified syringes with holes > or = 5.0 microm.

  15. 46 CFR 170.015 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... the sources listed below. (b) ASTM International (formerly American Society for Testing and Materials) (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959: (1) ASTM F 1196-00, Standard Specification for Sliding Watertight Door Assemblies (2000) (“ASTM F 1196”), 170.270; and (2) ASTM F 1197-00...

  16. 40 CFR 799.5087 - Chemical testing requirements for second group of high production volume chemicals (HPV2).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...: ASTM E 729-96 (Reapproved 2007) 3. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97 (Reapproved 2004) 2. Toxicity to Plants (Algae): ASTM E 1218... Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97...

  17. 40 CFR 799.5087 - Chemical testing requirements for second group of high production volume chemicals (HPV2).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...: ASTM E 729-96 (Reapproved 2007) 3. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97 (Reapproved 2004) 2. Toxicity to Plants (Algae): ASTM E 1218... Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97...

  18. 40 CFR 799.5087 - Chemical testing requirements for second group of high production volume chemicals (HPV2).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...: ASTM E 729-96 (Reapproved 2007) 3. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97 (Reapproved 2004) 2. Toxicity to Plants (Algae): ASTM E 1218... Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97...

  19. 40 CFR 799.5087 - Chemical testing requirements for second group of high production volume chemicals (HPV2).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...: ASTM E 729-96 (Reapproved 2007) 3. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97 (Reapproved 2004) 2. Toxicity to Plants (Algae): ASTM E 1218... Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity to Daphnia: ASTM E 1193-97...

  20. 75 FR 30440 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-01

    ... Production Act of 1993--ASTM International Notice is hereby given that, on May 6, 2010, pursuant to Section 6... Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the Attorney... recovery of antitrust plaintiffs to actual damages under specified circumstances. Specifically, ASTM has...

  1. 46 CFR 163.003-3 - ASTM standard.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false ASTM standard. 163.003-3 Section 163.003-3 Shipping...: SPECIFICATIONS AND APPROVAL CONSTRUCTION Pilot Ladder § 163.003-3 ASTM standard. The following standard of the American Society for Testing and Materials (ASTM) is incorporated by reference into this subpart: ASTM D...

  2. Oxidative induction time -- A review of DSC experimental effects

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Blaine, R.L.; Lundgren, C.J.; Harris, M.B.

    1997-12-31

    Over the past several years, a number of ASTM committees have explored a wide variety of experimental parameters affecting the oxidative induction time (OIT) test method in an attempt to improve its intra- and inter-laboratory precision. These studies have identified test temperature precision as a key parameter affecting OIT precision. Other parameters of importance are oxygen flow rate, specimen size, specimen pan type, oxygen pressure and catalyst effects. The work of Kuck, Bowmer, Riga, Tikuisis and Thomas are reviewed as well as the collective work of ASTM Committees E37, D2, D9 and D35.

  3. Twenty new ISO standards on dosimetry for radiation processing

    NASA Astrophysics Data System (ADS)

    Farrar, H., IV

    2000-03-01

    Twenty standards on essentially all aspects of dosimetry for radiation processing were published as new ISO standards in December 1998. The standards are based on 20 standard practices and guides developed over the past 14 years by Subcommittee E10.01 of the American Society for Testing and Materials (ASTM). The transformation to ISO standards using the 'fast track' process under ISO Technical Committee 85 (ISO/TC85) commenced in 1995 and resulted in some overlap of technical information between three of the new standards and the existing ISO Standard 11137 Sterilization of health care products — Requirements for validation and routine control — Radiation sterilization. Although the technical information in these four standards was consistent, compromise wording in the scopes of the three new ISO standards to establish precedence for use were adopted. Two of the new ISO standards are specifically for food irradiation applications, but the majority apply to all forms of gamma, X-ray, and electron beam radiation processing, including dosimetry for sterilization of health care products and the radiation processing of fruit, vegetables, meats, spices, processed foods, plastics, inks, medical wastes, and paper. Most of the standards provide exact procedures for using individual dosimetry systems or for characterizing various types of irradiation facilities, but one covers the selection and calibration of dosimetry systems, and another covers the treatment of uncertainties using the new ISO Type A and Type B evaluations. Unfortunately, nine of the 20 standards just adopted by the ISO are not the most recent versions of these standards and are therefore already out of date. To help solve this problem, efforts are being made to develop procedures to coordinate the ASTM and ISO development and revision processes for these and future ASTM-originating dosimetry standards. In the meantime, an additional four dosimetry standards have recently been published by the ASTM but have not yet been submitted to the ISO, and six more dosimetry standards are under development.

  4. 46 CFR 54.01-1 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ...) ASTM International (formerly American Society for Testing and Materials) (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959: (1) ASTM A 20/A 20M-97a, Standard Specification for General Requirements for Steel Plates for Pressure Vessels (“ASTM A 20”), 54.05-10; 54.25-10; (2) ASTM A 203/A 203M-97...

  5. Final Report, Volume 2, The Development of Qualification Standards for Cast Duplex Stainless Steel

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Russell, Steven, W.; Lundin, Carl, W.

    2005-09-30

    The scope of testing cast Duplex Stainless Steel (DSS) required testing to several ASTM specifications, while formulating and conducting industry round robin tests to verify and study the reproducibility of the results. ASTM E562 (Standard Test Method for Determining Volume Fraction by Systematic manual Point Count) and ASTM A923 (Standard Test Methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic/Ferritic Stainless Steels) were the specifications utilized in conducting this work. An ASTM E562 industry round robin, ASTM A923 applicability study, ASTM A923 industry round robin, and an ASTM A923 study of the effectiveness of existing foundry solution annealing proceduresmore » for producing cast DSS without intermetallic phases were implemented. In the ASTM E562 study, 5 samples were extracted from various cast austenitic and DSS in order to have varying amounts of ferrite. Each sample was metallographically prepared by UT and sent to each of 8 participants for volume fraction of ferrite measurements. Volume fraction of ferrite was measured using manual point count per ASTM E562. FN was measured from the Feritescope® and converted to volume fraction of ferrite. Results indicate that ASTM E562 is applicable to DSS and the results have excellent lab-to-lab reproducibility. Also, volume fraction of ferrite conversions from the FN measured by the Feritescope® were similar to volume fraction of ferrite measured per ASTM E562. In the ASTM A923 applicability to cast DSS study, 8 different heat treatments were performed on 3 lots of ASTM A890-4A (CD3MN) castings and 1 lot of 2205 wrought DSS. The heat treatments were selected to produce a wide range of cooling rates and hold times in order to study the suitability of ASTM A923 to the response of varying amounts on intermetallic phases [117]. The test parameters were identical to those used to develop ASTM A923 for wrought DSS. Charpy V-notch impact samples were extracted from the castings and wrought DSS and tested per ASTM A923 method B (Charpy impact test). Method A (sodium hydroxide etch test) was performed on one half of a fractured Charpy V-notch impact sample and Method C (ferric chloride corrosion weight loss test) was performed on another half. Test results for the three cast lots and one wrought lot indicate that ASTM A923 is relevant for detecting intermetallic phases in cast DSS. In the ASTM A923 round robin study, five laboratories conducted ASTM A923 Methods A & C on cast DSS material and the lab-to-lab reproducibility of the data was determined. Two groups of samples were sent to the participants. Group 1 samples were tested per ASTM A923 Method A, group 2 samples were tested by ASTM A923 Method C. Testing procedures for this round robin study were identical to those used in the ASTM A923 applicability study. Results from this round robin indicate that there is excellent lab-to-lab reproducibility of ASTM A923 with respect to cast DSS and that ASTM A923 could be expanded to cover both wrought and cast DSS. In the ASTM A923 study of the effectiveness of existing foundry solution annealing procedures for producing cast DSS without intermetallic phases, Ten heats of ASTM A890-4A (CD3MN) in the foundry solution annealed condition were tested per ASTM A923 Methods A, B, & C. Testing of these materials per ASTM A923 was used to determine if the foundry solution anneal procedures were adequate to completely eliminate any intermetallic phases, which may have precipitated during the casting and subsequent heat treatment processes. All heats showed no sign of intermetallic phase per Method A, passed minimum Charpy impact energy requirements per Method B (> 40 ft-lbs @ -40°C (-40°F)), and showed negligible weight loss per Method C (< 10 mdd). These results indicate that the solution annealing procedure used by foundries is adequate to produce a product free from intermetallic phases.« less

  6. Final Report, Volume 2, The Development of Qualification Standards for Cast Duplex Stainless Steel

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Russell, Steven, W.; Lundin, Carl, D.

    2005-09-30

    The scope of testing cast Duplex Stainless Steel (DSS) required testing to several ASTM specifications, while formulating and conducting industry round robin tests to verify and study the reproducibility of the results. ASTM E562 (Standard Test Method for Determining Volume Fraction by Systematic manual Point Count) and ASTM A923 (Standard Test Methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic/Ferritic Stainless Steels) were the specifications utilized in conducting this work. An ASTM E562 industry round robin, ASTM A923 applicability study, ASTM A923 industry round robin, and an ASTM A923 study of the effectiveness of existing foundry solution annealing proceduresmore » for producing cast DSS without intermetallic phases were implemented. In the ASTM E562 study, 5 samples were extracted from various cast austenitic and DSS in order to have varying amounts of ferrite. Each sample was metallographically prepared by UT and sent to each of 8 participants for volume fraction of ferrite measurements. Volume fraction of ferrite was measured using manual point count per ASTM E562. FN was measured from the Feritescope{reg_sign} and converted to volume fraction of ferrite. Results indicate that ASTM E562 is applicable to DSS and the results have excellent lab-to-lab reproducibility. Also, volume fraction of ferrite conversions from the FN measured by the Feritescope{reg_sign} were similar to volume fraction of ferrite measured per ASTM E562. In the ASTM A923 applicability to cast DSS study, 8 different heat treatments were performed on 3 lots of ASTM A890-4A (CD3MN) castings and 1 lot of 2205 wrought DSS. The heat treatments were selected to produce a wide range of cooling rates and hold times in order to study the suitability of ASTM A923 to the response of varying amounts on intermetallic phases [117]. The test parameters were identical to those used to develop ASTM A923 for wrought DSS. Charpy V-notch impact samples were extracted from the castings and wrought DSS and tested per ASTM A923 method B (Charpy impact test). Method A (sodium hydroxide etch test) was performed on one half of a fractured Charpy V-notch impact sample and Method C (ferric chloride corrosion weight loss test) was performed on another half. Test results for the three cast lots and one wrought lot indicate that ASTM A923 is relevant for detecting intermetallic phases in cast DSS. In the ASTM A923 round robin study, five laboratories conducted ASTM A923 Methods A & C on cast DSS material and the lab-to-lab reproducibility of the data was determined. Two groups of samples were sent to the participants. Group 1 samples were tested per ASTM A923 Method A, group 2 samples were tested by ASTM A923 Method C. Testing procedures for this round robin study were identical to those used in the ASTM A923 applicability study. Results from this round robin indicate that there is excellent lab-to-lab reproducibility of ASTM A923 with respect to cast DSS and that ASTM A923 could be expanded to cover both wrought and cast DSS. In the ASTM A923 study of the effectiveness of existing foundry solution annealing procedures for producing cast DSS without intermetallic phases, Ten heats of ASTM A890-4A (CD3MN) in the foundry solution annealed condition were tested per ASTM A923 Methods A, B, & C. Testing of these materials per ASTM A923 was used to determine if the foundry solution anneal procedures were adequate to completely eliminate any intermetallic phases, which may have precipitated during the casting and subsequent heat treatment processes. All heats showed no sign of intermetallic phase per Method A, passed minimum Charpy impact energy requirements per Method B (> 40 ft-lbs {at} -40 C (-40 F)), and showed negligible weight loss per Method C (< 10 mdd). These results indicate that the solution annealing procedure used by foundries is adequate to produce a product free from intermetallic phases.« less

  7. 40 CFR 1065.701 - General requirements for test fuels.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... procedure 1 Light distillate and light blends with residual ASTM D975-07b. Diesel Middle distillate ASTM D6985-04a. Biodiesel (B100) ASTM D6751-07b. Intermediate and residual fuel All See § 1065.705. Gasoline Motor vehicle gasoline ASTM D4814-07a. Minor oxygenated gasoline blends ASTM D4814-07a. Alcohol Ethanol...

  8. 40 CFR Appendix A to Subpart II of... - VOC Data Sheet 1

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...: (Dc)s __ g/L [] ASTM D1475-90 *[] Other 3 B. Total Volatiles: (mv)s __ Mass Percent [] ASTM D2369-93....14. 3 Explain the other method used under “Remarks.” [] ASTM D3792-91 *[] ASTM D4017-81, 90, or 96a... (nonvolatiles) 2. __ g/L coating (less water and exempt compounds) G. Thinner Density: Dth __ g/L ASTM...

  9. 76 FR 1459 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-ASTM International

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-10

    ... Production Act of 1993-ASTM International Notice is hereby given that, on December 6, 2010, pursuant to.... (``the Act''), ASTM International (``ASTM'') has filed written notifications simultaneously with the...

  10. On-Board Monitoring of Engine Oil

    DTIC Science & Technology

    2011-04-01

    Viscosity of Transparent and Opaque Liquids at 40°C Infracal Soot Meter Karl Fischer Titration ASTM D 664 Standard Test Method for Acid Number of... methods involve potentiometric and colorimetric titrations, respectively. For both tests, a titration solvent is prepared and added to the oil. The...ASTM D 2896 and ASTM D 4739 [17]. Both methods involve potentiometric titrations. ASTM D 2896 uses a stronger acid and more polar solvent than ASTM D

  11. 76 FR 13631 - Food and Drug Administration Modernization Act of 1997: Modifications to the List of Recognized...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-14

    ... equipment. I. Tissue Engineering 15-25 ASTM F2312--10 Standard ASTM F2312-10. Terminology Relating to Tissue Engineered Medical Products. 15-26 ASTM F2211--04 Standard ASTM F2211-04. Classification for Tissue...

  12. 40 CFR 799.5085 - Chemical testing requirements for first group of high production volume chemicals (HPV1).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    .... Toxicity to Plants (Algae): ASTM E 1218 Test Group 2 for C1: 1. Chronic Toxicity to Daphnia: ASTM E 1193 2. Toxicity to Plants (Algae): ASTM E 1218 The following are the special conditions for C1, C2, C3, C4, C5.... Acute Toxicity to Daphnia: ASTM E 729 2. Toxicity to Plants (Algae): ASTM E 1218 Test Group 2 for C2: 1...

  13. 40 CFR 1065.720 - Liquefied petroleum gas.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., C3H8 Minimum, 0.85 m3/m3 ASTM D2163-05. Vapor pressure at 38 °C Maximum, 1400 kPa ASTM D1267-02 or 2598-022. Volatility residue (evaporated temperature, 35 °C) Maximum, −38 °C ASTM D1837-02a. Butanes Maximum, 0.05 m3/m3 ASTM D2163-05. Butenes Maximum, 0.02 m3/m3 ASTM D2163-05. Pentenes and heavier Maximum...

  14. Is the apical soft tissue margin a better predictor of biochemical recurrence than the surgical specimen?

    PubMed

    Godoy, Guilherme; Tareen, Basir U; Lepor, Herbert

    2011-01-01

    To identify predictors of apical surgical margin (ASM) and apical soft tissue margin (ASTM), determine if the ASTM is a better predictor of biochemical recurrence (BR) than the ASM, and ascertain the impact of apical biopsies on BR rates. One thousand three hundred eight consecutive men underwent open radical retropubic prostatectomy (RP) between October 2000 and December 2006. Circumferential biopsies of the ASTM were obtained intraoperatively and submitted for frozen section analysis. Logistic regression models were utilized to identify the factors associated with the presence of positive ASMs and ASTMs. The estimated 5-year risk of BR was calculated by the Kaplan-Meier method. Overall, 43 (3.3%) and 86 (6.6%) of cases exhibited positive ASM and ASTM, respectively. ASM was significantly associated with higher mean serum prostate-specific antigen levels, presence of perineural invasion, and greater volume of tumor in the biopsy specimen. None of these factors were observed to be associated with the presence of cancer in the ASTMs. In the multivariate analysis, only the presence of perineural invasion was a significant independent predictor of ASMs. The estimated 5-year BR rates in the positive ASMs only, ASTMs only, and both positive ASMs and ASTMs groups were 48.6%, 4.7%, and 38.8%, respectively. A positive ASM was associated with a significantly greater risk of BR compared with a positive ASTM. The very low estimated risk of BR at 5 years in cases with ASTM suggests that performing the ASTM biopsies may increase the cure rates achieved with RP. Copyright © 2011 Elsevier Inc. All rights reserved.

  15. 40 CFR 312.11 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... the requirements set forth in §§ 312.23 through 312.31: (a) The procedures of ASTM International... Site Assessment Process.” (b) The procedures of ASTM International Standard E2247-08 entitled “Standard... or Rural Property.” This standard is available from ASTM International at http://www.astm.org, 1-610...

  16. 40 CFR 799.5089 - Chemical testing requirements for third group of high production volume chemicals (HPV3).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Toxicity to Daphnia: ASTM E 729-96 (Reapproved 2007). 3. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test... (Algae): ASTM E 1218-04 e1 The following are the special conditions for C1, C2, C3, C4, C5, and C7.... Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity to Daphnia: ASTM E...

  17. Evaluation of Storage Effects on Commercial, Biodegradable, Synthetic or Bio-sourced Hydraulic Fluid

    DTIC Science & Technology

    2007-01-10

    Water Content (ASTM D 6304) Coulometric Karl Fischer Titration for water content was conducted in accordance with ASTM D 6304, Standard Test Method ...Point7 (ASTM D 92) • Lubricity (4-Ball Wear)8 (ASTM D 4172) • Total Acid Number (TAN)9 (ASTM D 664) • Water Content by Karl Fischer Coulometric...2001 and the data from FLTT in 2005. However, FLTT procured a new Karl Fischer water titrator in 2003. But FLTT continued to use the same

  18. Rapid Response Research and Development (R&D) for the Aerospace Systems Directorate. Delivery Order 0021: Engineering Research and Technical Analyses of Advanced Airbreathing Propulsion Fuels, Subtask: Engine and Pump Studies Utilizing JP-8 and Alcohol-to-Jet (ATJ) Blends

    DTIC Science & Technology

    2014-08-01

    41 Figure A-21. Lubricant Soot Accumulation...ASTM D4739 Total Base Number ASTM D664 Total Acid Number ASTM D445 Kinematic Viscosity @ 100°C ASTM D4052 Density ASTM TGA SOOT TGA Soot ASTM E168...118.85 134.01 145.47 169.22 187.43 342.42 Nitration (Abs./cm) E168 FTIR 0 6.67 10.91 16.54 19.04 25.79 35.12 24.03 23.75 52.31 93.9 Soot (%) Soot TGA

  19. 40 CFR 94.5 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    .../code_of_federal_regulations/ibr_locations.html. (a) ASTM material. Table 1 of § 94.5 lists material... of § 94.5—ASTM Materials Document No. and name Part 94 reference ASTM D 86-01, Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure 94.108 ASTM D 93-02, Standard Test...

  20. 47 CFR 95.1509 - ASTM E2213-03 DSRC Standard.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false ASTM E2213-03 DSRC Standard. 95.1509 Section 95... ASTM E2213-03 DSRC Standard. On-Board Units operating in the 5850-5925 MHz band shall comply with the... Materials (ASTM) E2213-03, Standard Specification for Telecommunications and Information Exchange Between...

  1. 16 CFR 1203.53 - Interim safety standards.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ..., Protective Headgear for Bicyclists, (2) ASTM standards F 1447-93 or F 1447-94, Standard Specification for Protective Headgear Used in Bicycling, incorporating the relevant provisions of ASTM F 1446-93 or ASTM F 1446... Institute, 11 W. 42nd Street, 13th Floor, New York, NY 10036. Copies of the ASTM standards are available...

  2. Polymer dispensing and embossing technology for the lens type LED packaging

    NASA Astrophysics Data System (ADS)

    Chien, Chien-Lin Chang; Huang, Yu-Che; Hu, Syue-Fong; Chang, Chung-Min; Yip, Ming-Chuen; Fang, Weileun

    2013-06-01

    This study presents a ring-type micro-structure design on the substrate and its corresponding micro fabrication processes for a lens-type light-emitting diode (LED) package. The dome-type or crater-type silicone lenses are achieved by a dispensing and embossing process rather than a molding process. Silicone with a high viscosity and thixotropy index is used as the encapsulant material. The ring-type micro structure is adopted to confine the dispensed silicone encapsulant so as to form the packaged lens. With the architecture and process described, this LED package technology herein has three merits: (1) the flexibility of lens-type LED package designs is enhanced; (2) a dome-type package design is used to enhance the intensity; (3) a crater-type package design is used to enhance the view angle. Measurement results show the ratio between the lens height and lens radius can vary from 0.4 to 1 by changing the volume of dispensed silicone. The view angles of dome-type and crater-type packages can reach 155° ± 5° and 175° ± 5°, respectively. As compared with the commercial plastic leaded chip carrier-type package, the luminous flux of a monochromatic blue light LED is improved by 15% by the dome-type package (improved by 7% by the crater-type package) and the luminous flux of a white light LED is improved by 25% by the dome-type package (improved by 13% by the crater-type package). The luminous flux of monochromatic blue light LED and white light LED are respectively improved by 8% and 12% by the dome-type package as compare with the crater-type package.

  3. 49 CFR 192.177 - Additional provisions for bottle-type holders.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... in accordance with § 192.327. (b) Each bottle-type holder manufactured from steel that is not... steel must meet the chemical and tensile requirements for the various grades of steel in ASTM A 372/A 372M. (2) The actual yield-tensile ratio of the steel may not exceed 0.85. (3) Welding may not be...

  4. 49 CFR 192.177 - Additional provisions for bottle-type holders.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... in accordance with § 192.327. (b) Each bottle-type holder manufactured from steel that is not... steel must meet the chemical and tensile requirements for the various grades of steel in ASTM A 372/A 372M. (2) The actual yield-tensile ratio of the steel may not exceed 0.85. (3) Welding may not be...

  5. 46 CFR 56.01-2 - Incorporation by reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Steel Pipe for High-Temperature Service (“ASTM A 106”), 56.60-1; (5) ASTM A 126-95, Standard... (1996), Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service (“ASTM A...-Resistance-Welded Carbon Steel Boiler and Superheater Tubes for High-Pressure Service (“ASTM A 226”), 56.60-1...

  6. NREL-Led Effort Results in Groundbreaking New ASTM High-Octane Fuel

    Science.gov Websites

    Standard | News | NREL NREL-Led Effort Results in Groundbreaking New ASTM High-Octane Fuel Standard NREL-Led Effort Results in Groundbreaking New ASTM High-Octane Fuel Standard April 7, 2017 NREL . Photo by Dennis Schroeder, NREL 20114. ASTM International recently announced the release of a new high

  7. 46 CFR 164.120-5 - Incorporation by reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ...), IBR approved for § 164.120-7 (“ASTM D 543”). (2) ASTM D 570-98 (Reapproved 2005), Standard Test Method for Water Absorption of Plastics, (approved November 1, 2005), IBR approved for § 164.120-7 (“ASTM D 570”). (3) ASTM D 638-08, Standard Test Method for Tensile Properties of Plastics, (approved April 1...

  8. 77 FR 33733 - Regulation of Fuel and Fuel Additives: Modification to Octamix Waiver (TXCeed)

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-07

    ... must meet ASTM volatility specifications contained in ASTM D439-85a, as well as phase separation conditions specified in ASTM D-2 Proposal P-176 and Texas Methanol alcohol purity specifications. \\4\\ 53 FR..., TXCeed, met ASTM \\11\\ and NACE \\12\\ corrosion test results, as well as physical property information. \\11...

  9. 27 CFR 21.107 - Ethyl acetate.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part 29, page 70, Standard No. D 302-58 (1975.... (5) Specific gravity at 20 °/20 °C. Not less than 0.899. (6) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part 29, page 433, Standard No. D 3127-77; for...

  10. 40 CFR 1060.810 - What materials does this part reference?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    .... (a) ASTM material. Table 1 to this section lists material from the American Society for Testing and..., West Conshohocken, PA 19428 or http://www.astm.com. Table 1 follows: Table 1 to § 1060.810—ASTM Materials Document number and name Part 1060reference ASTM D471-06, Standard Test Method for Rubber Property...

  11. Current activities in standardization of high-temperature, low-cycle-fatigue testing techniques in the United States

    NASA Technical Reports Server (NTRS)

    Verrilli, Michael J.; Ellis, J. Rodney; Swindeman, Robert W.

    1990-01-01

    The American Society for Testing and Materials (ASTM) standard E606-80 is the most often used recommended testing practice for low-cycle-fatigue (LCF) testing in the United States. The standard was first adopted in 1977 for LCF testing at room temperature and was modified in 1980 to include high-temperature testing practices. Current activity within ASTM is aimed at extending the E606-80 recommended practices to LCF under thermomechanical conditions, LCF in high-pressure hydrogen, and LCF in metal-matrix composite materials. Interlaboratory testing programs conducted to generate a technical base for modifying E606-80 for the aforementioned LCF test types are discussed.

  12. XML and its impact on content and structure in electronic health care documents.

    PubMed Central

    Sokolowski, R.; Dudeck, J.

    1999-01-01

    Worldwide information networks have the requirement that electronic documents must be easily accessible, portable, flexible and system-independent. With the development of XML (eXtensible Markup Language), the future of electronic documents, health care informatics and the Web itself are about to change. The intent of the recently formed ASTM E31.25 subcommittee, "XML DTDs for Health Care", is to develop standard electronic document representations of paper-based health care documents and forms. A goal of the subcommittee is to work together to enhance existing levels of interoperability among the various XML/SGML standardization efforts, products and systems in health care. The ASTM E31.25 subcommittee uses common practices and software standards to develop the implementation recommendations for XML documents in health care. The implementation recommendations are being developed to standardize the many different structures of documents. These recommendations are in the form of a set of standard DTDs, or document type definitions that match the electronic document requirements in the health care industry. This paper discusses recent efforts of the ASTM E31.25 subcommittee. PMID:10566338

  13. 40 CFR 98.7 - What standardized methods are incorporated by reference into this part?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ....astm.org. (1) ASTM C25-06 Standard Test Method for Chemical Analysis of Limestone, Quicklime, and....194(c), and § 98.334(b). (2) ASTM C114-09 Standard Test Methods for Chemical Analysis of Hydraulic... approved for § 98.6. (4) ASTM D240-02 (Reapproved 2007) Standard Test Method for Heat of Combustion of...

  14. 40 CFR 98.7 - What standardized methods are incorporated by reference into this part?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ....astm.org. (1) ASTM C25-06 Standard Test Method for Chemical Analysis of Limestone, Quicklime, and....194(c), and § 98.334(b). (2) ASTM C114-09 Standard Test Methods for Chemical Analysis of Hydraulic... approved for § 98.6. (4) ASTM D240-02 (Reapproved 2007) Standard Test Method for Heat of Combustion of...

  15. 46 CFR 56.01-2 - Incorporation by reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...”), 56.10-5; 56.60-1; (4) ASTM A 106-95, Standard Specification for Seamless Carbon Steel Pipe for High...), Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service (“ASTM A 192”), 56... Steel Boiler and Superheater Tubes for High-Pressure Service (“ASTM A 226”), 56.60-1; (19) ASTM A 234/A...

  16. 46 CFR 56.01-2 - Incorporation by reference.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ...”), 56.10-5; 56.60-1; (4) ASTM A 106-95, Standard Specification for Seamless Carbon Steel Pipe for High...), Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service (“ASTM A 192”), 56... Steel Boiler and Superheater Tubes for High-Pressure Service (“ASTM A 226”), 56.60-1; (19) ASTM A 234/A...

  17. 29 CFR Appendix A to Subpart Q of... - References to subpart Q of Part 1926

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (ASTM C39-86). • Standard Test Method for Making and Curing Concrete Test Specimens in the Field (ASTM C31-85). • Standard Test Method for Penetration Resistance of Hardened Concrete (ASTM C803-82... (ASTM C873-85). • Standard Method for Developing Early Age Compressive Test Values and Projecting Later...

  18. 76 FR 2056 - Incorporation of Revised ASTM Standards That Provide Flexibility in the Use of Alternatives to...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-12

    ... Sulfur in Petroleum Products (General Bomb Method); ASTM D2622-98, Standard Test Method for Sulfur in...; ASTM D240-00, Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb... Liquid Hydrocarbon Fuels by Bomb Calorimeter, ASTM D4809-00, Standard Test Method for Heat of Combustion...

  19. 46 CFR 175.600 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Vessels Under 61 Meters (200 feet) in Length, 1983 (“ABS Steel Vessel Rules (Meters)”) 177.300. Rules..., Standard Practice for Operating Salt Spray (Fog) Apparatus (“ASTM B 117”) 175.400. ASTM B 122/B 122M-95... (“ASTM D 93”) 175.400. ASTM D 635-97, Standard test Method for Rate of Burning and or Extent and Time of...

  20. Effect of portland cement (current ASTM C150/AASHTO M85) with limestone and process addition (ASTM C465/AASHTO M327) on the performance of concrete for pavement and bridge decks.

    DOT National Transportation Integrated Search

    2014-02-01

    The Illinois Department of Transportation (IDOT) is making several changes to concrete mix designs, using revisions to : cement specification ASTM C150/AASHTO M85 and ASTM C465/AASHTO M327. These proposed revisions will enable the : use of more susta...

  1. 46 CFR 174.007 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... are: American Society for Testing and Materials (ASTM) 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM F 1196-94, Standard Specification for Sliding Watertight Door Assemblies—174.100 ASTM F...

  2. 46 CFR 161.006-1 - Applicable specifications.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., and strip. (3) Standards of ASTM: ASTM B 117-97, Standard Practice for Operating Salt Spray (Fog) Apparatus—161.006-5 ASTM B 456-95, Standard Specification for Electrodeposited Coatings of Copper Plus...

  3. 40 CFR 98.7 - What standardized methods are incorporated by reference into this part?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...-B2959, (800) 262-1373, http://www.astm.org. (1) ASTM C25-06 Standard Test Method for Chemical Analysis...), § 98.174(b), § 98.184(b), § 98.194(c), and § 98.334(b). (2) ASTM C114-09 Standard Test Methods for... Dry Cleaning Solvent), IBR approved for § 98.6. (4) ASTM D240-02 (Reapproved 2007) Standard Test...

  4. Method for Estimating Evaporative Potential (IM/CLO) from ASTM Standard Single Wind Velocity Measures

    DTIC Science & Technology

    2016-08-10

    IM/CLO) FROM ASTM STANDARD SINGLE WIND VELOCITY MEASURES DISCLAIMER The opinions or assertions contained herein are the private views of the...USARIEM TECHNICAL REPORT T16-14 METHOD FOR ESTIMATING EVAPORATIVE POTENTIAL (IM/CLO) FROM ASTM STANDARD SINGLE WIND VELOCITY...ASTM STANDARD SINGLE WIND VELOCITY MEASURES Adam W. Potter Biophysics and Biomedical Modeling Division U.S. Army Research Institute of Environmental

  5. 40 CFR 1065.710 - Gasoline.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...: Initial boiling point °C 24-35 2 24-36 10% point °C 49-57 37-48 ASTM D86-07a. 50% point °C 93-110 82-101... m3/m3 Maximum, 0.10 Maximum, 0.175 ASTM D1319-03. Aromatics Maximum, 0.35 Maximum, 0.304 Saturates.../liter Maximum, 0.0013 Maximum, 0.005 ASTM D3231-07. Total sulfur mg/kg Maximum, 80 Maximum, 80 ASTM...

  6. Environmental Assisted Cracking in High Hardness Armor Steel

    DTIC Science & Technology

    1985-09-01

    Longitudinal and transverse tension tests (ASTM E8-81) utilizing flat dogbane specimens, and subsize Charpy impact tests (ASTM 23-81) were performed on part...had been obtained. Longitudinal and transverse tension tests (ASTM E8-81) utilizing flat dogbane specimens, and subsize Charpy impact tests (ASTM 23... Charpy and tensile bar surfaces. All of the optical metallography samples were prepared using standard metallographic practices. The optical specimens

  7. Structure-Property Relations in Aluminum-Lithium Alloys

    DTIC Science & Technology

    1989-01-01

    adsorbed ( Mughrabi et al , 1983). Such dislocations could not re-enter the grain during the reverse cycle of stress and the associated slip would be...ASTM STP 601, ASTM, 33 Mughrabi , H., Wang, R., Differt, D., Essmann, U. (1983) ASTM STP 811, ASTM, 5 Muller, W. et al (1986) Aluminium-Lithium Alloys...behaviour of Al -Li-Cu-Mg-Zr alloys ...... 34 2.4 Mechanical behaviour ......................................... 35 2.4.1 Elastic modulus

  8. 46 CFR 30.01-3 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, telephone 610-832-9585, http://www.astm.org. (1) ASTM D 323-94, Standard Test Method for Vapor Pressure of Petroleum Products...

  9. 46 CFR 105.01-3 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... from the sources listed below. (b) American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, telephone 610-832-9585, http://www.astm.org. (1) ASTM D 323-94...

  10. 46 CFR 163.003-3 - ASTM standard.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... American Society for Testing and Materials (ASTM) is incorporated by reference into this subpart: ASTM D... Society at 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. [USCG-1999-5151, 64 FR 67185, Dec. 1...

  11. Management of Civil Engineering Support Equipment

    DTIC Science & Technology

    2003-09-01

    The standard Navy plates have blue lettering on a white reflective background (Shore) or black lettering on a non-reflective olive drab background...17038. 2-54 (b) On vehicles painted white, individual letters and numbers shall be the reflective type, conforming to Type I, Class 3, Blue ...manufacturer’s color. The word “Police” in 4-inch reflectorized blue letters of material conforming to ASTM D4956, Type III, Class 1 (encapsulated lens), shall

  12. Sources of Confusion in the Determination of ASTM Repetitive Member Factors for the Allowable Properties of Wood Products

    Treesearch

    S. Verrill; D. Kretschmann

    2012-01-01

    It is generally accepted that there should be an upward repetitive member allowable property adjustment. ASTM D245 (2011c) and ASTM D1990 (2011b) specify a 1.15 factor for allowable bending stress. This factor is also listed in ASTM D6555 (2011a, Table 1). In this technical note, sources of confusion regarding appropriate repetitive member factors are identified. This...

  13. 49 CFR 178.350 - Specification 7A; general packaging, Type A.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Specification 7A; general packaging, Type A. 178... FOR PACKAGINGS Specifications for Packagings for Class 7 (Radioactive) Materials § 178.350 Specification 7A; general packaging, Type A. (a) Each packaging must meet all applicable requirements of subpart...

  14. Behavior of standard hook anchorage with corrosion resistant reinforcement : final report, June 2008.

    DOT National Transportation Integrated Search

    2008-06-01

    The objective of this study was to evaluate the behavior of standard books that are made using corrosion resistant reinforcement, which typically have higher yield and ultimate strengths than that of ASTM A615 Grade 60 reinforcement. Two steel types ...

  15. Image analysis of corrosion pit initiation on ASTM type A240 stainless steel and ASTM type A 1008 carbon steel

    NASA Astrophysics Data System (ADS)

    Nine, H. M. Zulker

    The adversity of metallic corrosion is of growing concern to industrial engineers and scientists. Corrosion attacks metal surface and causes structural as well as direct and indirect economic losses. Multiple corrosion monitoring tools are available although those are time-consuming and costly. Due to the availability of image capturing devices in today's world, image based corrosion control technique is a unique innovation. By setting up stainless steel SS 304 and low carbon steel QD 1008 panels in distilled water, half-saturated sodium chloride and saturated sodium chloride solutions and subsequent RGB image analysis in Matlab, in this research, a simple and cost-effective corrosion measurement tool has identified and investigated. Additionally, the open circuit potential and electrochemical impedance spectroscopy results have been compared with RGB analysis to gratify the corrosion. Additionally, to understand the importance of ambiguity in crisis communication, the communication process between Union Carbide and Indian Government regarding the Bhopal incident in 1984 was analyzed.

  16. Poststapedectomy hearing gain: comparison of a Teflon (fluoroplastic ASTM F 754) prosthesis with a Schuknecht-type wire/Teflon prosthesis.

    PubMed

    Zepeda-López, Emilia Guadalupe; Bello-Mora, Antonio; Félix-Trujillo, Manuel Martín

    2005-11-01

    We conducted a retrospective study to compare poststapedectomy hearing gain in study-eligible patients who had received a Teflon (fluoroplastic ASTM F 754) prosthesis (study group; n = 76) with hearing gain achieved in a matched group (by age, sex, and degree of hypoacusis) of patients who had received a Schuknecht-type wire/Teflon prosthesis (control group; n = 70). All procedures had been performed by the authors at our institution between Jan. 2, 1994, and Dec. 31, 1997. Airway averages at low, medium, and high frequencies were estimated on the basis ofpre- and postoperative audiologic evaluations, as were total air-bone gaps at 7 frequencies between 125 and 8, 000 Hz. We found that the study group achieved a significantly greater degree of hearing gain at 125 and 250 Hz and significantly better closure of the air-bone gap at 250, 500, 1,000, 2,000, and 4,000 Hz. The hearing outcomes among patients in the study group were excellent.

  17. 76 FR 78614 - Welded ASTM A-312 Stainless Steel Pipe From South Korea and Taiwan: Continuation of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-19

    ... standards and specifications set forth by the American Society for Testing and Materials (ASTM) for the... stainless steel flat-rolled products into a tubular configuration and welding along the seam. Welded ASTM A...

  18. 40 CFR 80.9 - Rounding a test result for determining conformance with a fuels standard.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... in the ASTM standard practice, ASTM E 29-02∈ 1, entitled, “Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications”. (b) ASTM standard practice, E 29-02∈ 1...

  19. Evaluation of Instrumentation for Measuring Undissolved Water in Aviation Turbine Fuels per ASTM D3240

    DTIC Science & Technology

    2015-11-05

    Undissolved Water in Aviation Turbine Fuels per ASTM D3240 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Joel Schmitigal... water ) in Aviation Turbine Fuels per ASTM D3240 15. SUBJECT TERMS fuel, JP-8, aviation fuel, contamination, free water , undissolved water , Aqua-Glo 16...Michigan 48397-5000 Evaluation of Instrumentation for Measuring Undissolved Water in Aviation Turbine Fuels per ASTM D3240 Joel Schmitigal Force

  20. Analysis and evaluation of the Electronic Health Record standard in China: a comparison with the American national standard ASTM E 1384.

    PubMed

    Xu, Wei; Guan, Zhiyu; Cao, Hongxin; Zhang, Haiyan; Lu, Min; Li, Tiejun

    2011-08-01

    To analyze and evaluate the newly issued Electronic Health Record (EHR) Architecture and Data Standard of China (Chinese EHR Standard) and identify areas of improvement for future revisions. We compared the Chinese EHR Standard with the standard of the American Society for Testing and Materials Standard Practice for Content and Structure of Electronic Health Records in the United States (ASTM E 1384 Standard). The comparison comprised two steps: (1) comparing the conformance of the two standards to the international standard: Health Informatics-Requirements for an Electronic Health Record Architecture (ISO/TS 18308), and showing how the architectures of the two standards satisfy or deviate from the ISO requirements and (2) comparing the detailed data structures between the two standards. Of the 124 requirement items in ISO/TS 18308, the Chinese EHR Standard and the ASTM E 1384 Standard conformed to 77 (62.1%) and 111 (89.5%), respectively. The Chinese EHR Standard conformed to 34 of 50 Structure requirements (68.0%), 22 of 24 Process requirements (91.7%), and 21 of 50 Other requirements (42.0%). The ASTM E 1384 Standard conformed to 49 of 50 Structure requirements (98.0%), 23 of 24 Process requirements (95.8%), and 39 of 40 Other requirements (78.0%). Further development of the Chinese EHR Standard should focus on supporting privacy and security mechanism, diverse data types, more generic and extensible lower level data structures, and relational attributes for data elements. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  1. Advancements in internationally accepted standards for radiation processing

    NASA Astrophysics Data System (ADS)

    Farrar, Harry; Derr, Donald D.; Vehar, David W.

    1993-10-01

    Three subcommittees of the American Society for Testing and Materials (ASTM) are developing standards on various aspects of radiation processing. Subcommittee E10.01 "Dosimetry for Radiation Processing" has published 9 standards on how to select and calibrate dosimeters, where to put them, how many to use, and how to use individual types of dosimeter systems. The group is also developing standards on how to use gamma, electron beam, and x-ray facilities for radiation processing, and a standard on how to treat dose uncertainties. Efforts are underway to promote inclusion of these standards into procedures now being developed by government agencies and by international groups such as the United Nations' International Consultative Group on Food Irradiation (ICGFI) in order to harmonize regulations and help avoid trade barriers. Subcommittee F10.10 "Food Processing and Packaging" has completed standards on good irradiation practices for meat and poultry and for fresh fruits, and is developing similar standards for the irradiation of seafood and spices. These food-related standards are based on practices previously published by ICGFI. Subcommittee E10.07 on "Radiation Dosimetry for Radiation Effects on Materials and Devices" principally develops standards for determining doses for radiation hardness testing of electronics. Some, including their standards on the Fricke and TLD dosimetry systems are equally useful in other radiation processing applications.

  2. Use of Niobium High Strength Steels with 450 MPA Yield Strength for Construction

    NASA Astrophysics Data System (ADS)

    Silvestre, Leonardo; Langenberg, Peter; Amaral, Thiago; Carboni, Marcelo; Meira, Marcos; Jordão, Alexandre

    This paper presents an actual case of a new industrial building at CBMM's plant in Araxá, Brazil as an example of lean design using microalloyed steels. The structure consists mostly of microalloyed ASTM A572 steel grades 65 and 50 instead of the conventional carbon manganese ASTM A36 steel. The application of grade 65 with more than 450 MPa of yield strength is an innovative solution for this type of construction in South America. A complete welding evaluation performed on the low carbon, niobium microalloyed grade 65 steel showed the welding properties and benefits. Niobium's effect of increasing strength and toughness simultaneously resulted in relevant savings in total steel consumption for the project. The paper also quantifies the expected savings in costs, energy and carbon dioxide emissions.

  3. ASTM and VAMAS activities in titanium matrix composites test methods development

    NASA Technical Reports Server (NTRS)

    Johnson, W. S.; Harmon, D. M.; Bartolotta, P. A.; Russ, S. M.

    1994-01-01

    Titanium matrix composites (TMC's) are being considered for a number of aerospace applications ranging from high performance engine components to airframe structures in areas that require high stiffness to weight ratios at temperatures up to 400 C. TMC's exhibit unique mechanical behavior due to fiber-matrix interface failures, matrix cracks bridged by fibers, thermo-viscoplastic behavior of the matrix at elevated temperatures, and the development of significant thermal residual stresses in the composite due to fabrication. Standard testing methodology must be developed to reflect the uniqueness of this type of material systems. The purpose of this paper is to review the current activities in ASTM and Versailles Project on Advanced Materials and Standards (VAMAS) that are directed toward the development of standard test methodology for titanium matrix composites.

  4. Improved ultrasonic standard reference blocks

    NASA Technical Reports Server (NTRS)

    Eitzen, D. G.; Sushinsky, G. F.; Chwirut, D. J.; Bechtoldt, C. J.; Ruff, A. W.

    1976-01-01

    A program to improve the quality, reproducibility and reliability of nondestructive testing through the development of improved ASTM-type ultrasonic reference standards is described. Reference blocks of aluminum, steel, and titanium alloys are to be considered. Equipment representing the state-of-the-art in laboratory and field ultrasonic equipment was obtained and evaluated. RF and spectral data on ten sets of ultrasonic reference blocks have been taken as part of a task to quantify the variability in response from nominally identical blocks. Techniques for residual stress, preferred orientation, and micro-structural measurements were refined and are applied to a reference block rejected by the manufacturer during fabrication in order to evaluate the effect of metallurgical condition on block response. New fabrication techniques for reference blocks are discussed and ASTM activities are summarized.

  5. 47 CFR 95.1509 - ASTM E2213-03 DSRC Standard.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ....1509 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES PERSONAL RADIO SERVICES Dedicated Short-Range Communications Service On-Board Units (DSRCS-OBUs) § 95.1509... 19428-2959. Copies may also be obtained from ASTM via the Internet at http://www.astm.org. ...

  6. 47 CFR 95.1509 - ASTM E2213-03 DSRC Standard.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ....1509 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES PERSONAL RADIO SERVICES Dedicated Short-Range Communications Service On-Board Units (DSRCS-OBUs) § 95.1509... 19428-2959. Copies may also be obtained from ASTM via the Internet at http://www.astm.org. ...

  7. 47 CFR 95.1509 - ASTM E2213-03 DSRC Standard.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ....1509 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES PERSONAL RADIO SERVICES Dedicated Short-Range Communications Service On-Board Units (DSRCS-OBUs) § 95.1509... 19428-2959. Copies may also be obtained from ASTM via the Internet at http://www.astm.org. ...

  8. 47 CFR 95.1509 - ASTM E2213-03 DSRC Standard.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ....1509 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES PERSONAL RADIO SERVICES Dedicated Short-Range Communications Service On-Board Units (DSRCS-OBUs) § 95.1509... 19428-2959. Copies may also be obtained from ASTM via the Internet at http://www.astm.org. ...

  9. 40 CFR 59.412 - Incorporations by reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... address: American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. (1) ASTM Method C 1315-95, Standard Specification for Liquid Membrane-Forming Compounds....401, Concrete curing and sealing compound. (2) ASTM Method D 523-89, Standard Test Method for Specular...

  10. 46 CFR 58.03-1 - Incorporation by reference.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Test Method for Flash and Fire Points by Cleveland Open Cup (“ASTM D 92”), 58.30-10; (8) ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester (“ASTM D 93”), 58.01-10; and (9...

  11. 46 CFR 58.03-1 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Test Method for Flash and Fire Points by Cleveland Open Cup (“ASTM D 92”), 58.30-10; (8) ASTM D 93-97, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester (“ASTM D 93”), 58.01-10; and (9...

  12. 77 FR 2456 - Incorporation of Revised ASTM Standards That Provide Flexibility in the Use of Alternatives to...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-18

    ... (General Bomb Method), IBR approved for appendix A to subpart D. (4) ASTM D287-92, Standard Test Method for... Method for Sulfur in Petroleum Products (General Bomb Method), IBR approved for Sec. 94.108. (4) ASTM...

  13. 49 CFR 173.415 - Authorized Type A packages.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Authorized Type A packages. 173.415 Section 173... REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.415 Authorized Type A packages. The following packages are authorized for shipment if they do not contain quantities exceeding A1 or...

  14. 49 CFR 173.415 - Authorized Type A packages.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Authorized Type A packages. 173.415 Section 173... REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.415 Authorized Type A packages. The following packages are authorized for shipment if they do not contain quantities exceeding A1 or...

  15. 49 CFR 173.415 - Authorized Type A packages.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Authorized Type A packages. 173.415 Section 173... REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.415 Authorized Type A packages. The following packages are authorized for shipment if they do not contain quantities exceeding A1 or...

  16. 49 CFR 173.415 - Authorized Type A packages.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Authorized Type A packages. 173.415 Section 173... REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.415 Authorized Type A packages. The following packages are authorized for shipment if they do not contain quantities exceeding A1 or...

  17. 46 CFR 56.50-105 - Low-temperature piping.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... ASTM E 23 (incorporated by reference, see § 56.01-2), “Notched Bar Impact Testing of Metallic Materials”, Type A, Figure 4. The toughness testing requirements of subpart 54.05 of this subchapter shall be... testing of production weldments for low temperature piping systems and assemblies is not required. (3...

  18. Racking strength of walls sheathed with structual flakeboards made from southern species

    Treesearch

    E.W. Price; Gromala D.S.

    1980-01-01

    Ten types of structural flakeboards and two types of southern pine plywood were evaluated. Racking loads were applied to full-size racking panels (8 by 8 ft., according to ASTME 72) and small panels (2 by 2 ft.). When subjected to a 1,600-pound racking load, 8- by 8-foot panels sheathed with flakeboards containing a mixture of hardwood and pine flakes were slightly...

  19. Study on ternary low density polyethylene/linear low density polyethylene/thermoplastic starch blend films.

    PubMed

    Sabetzadeh, Maryam; Bagheri, Rouhollah; Masoomi, Mahmood

    2015-03-30

    In this work, low-density polyethylene/linear low-density polyethylene/thermoplastic starch (LDPE/LLDPE/TPS) films are prepared with the aim of obtaining environmentally friendly materials containing high TPS content with required packaging properties. Blending of LDPE/LLDPE (70/30 wt/wt) with 5-20 wt% of TPS and 3 wt% of PE-grafted maleic anhydride (PE-g-MA) is performed in a twin-screw extruder, followed by the blowing process. Differential scanning calorimetric results indicate starch has more pronounced effect on crystallization of LLDPE than LDPE. Scanning electron micrograph shows a fairly good dispersion of TPS in PE matrices. Fourier transfer infrared spectra confirm compatibility between polymers using PE-g-MA as the compatibilizer. Storage modulus, loss modulus and complex viscosity increase with incorporation of starch. Tensile strength and elongation-at-break decrease from 18 to 10.5 MPa and 340 to 200%, respectively when TPS increases from 5 to 20%. However, the required mechanical properties for packaging applications are attained when 15 wt% starch is added, as specified in ASTM D4635. Finally 12% increase in water uptake is achieved with inclusion of 15 wt% starch. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. 40 CFR 92.5 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...: (1) ASTM material. The following table sets forth material from the American Society for Testing and...., Philadelphia, PA 19103. The table follows: Document number and name 40 CFR part 92 reference ASTM D 86-95, Standard Test Method for Distillation of Petroleum Products § 92.113 ASTM D 93-94, Standard Test Methods...

  1. 75 FR 51177 - Safety Standard for Infant Bath Seats; Correction

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-08-19

    ... a standard for infant bath seats by incorporating by reference ASTM F 1967-08a with certain changes... incorporating by reference ASTM F 1967-08. An introductory phrase in the stability performance requirements in the ASTM standard should have been removed to make the provision consistent with the Commission's...

  2. 40 CFR 59.110 - Incorporations by Reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Register. (1) ASTM D 1613-96, Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products, IBR approved for § 59.104(d). (2) ASTM D... Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA, 19428, telephone...

  3. Annual Book of ASTM Standards, Part 23: Water; Atmospheric Analysis.

    ERIC Educational Resources Information Center

    American Society for Testing and Materials, Philadelphia, PA.

    Standards for water and atmospheric analysis are compiled in this segment, Part 23, of the American Society for Testing and Materials (ASTM) annual book of standards. It contains all current formally approved ASTM standard and tentative test methods, definitions, recommended practices, proposed methods, classifications, and specifications. One…

  4. 40 CFR Table 4 to Subpart Zzzz of... - Requirements for Performance Tests

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... D6348-03,c provided in ASTM D6348-03 Annex A5 (Analyte Spiking Technique), the percent R must be greater... ASTM D6348-03,c provided in ASTM D6348-03 Annex A5 (Analyte Spiking Technique), the percent R must be...

  5. 40 CFR Table 4 to Subpart Zzzz of... - Requirements for Performance Tests

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... D6348-03,c provided in ASTM D6348-03 Annex A5 (Analyte Spiking Technique), the percent R must be greater... ASTM D6348-03,c provided in ASTM D6348-03 Annex A5 (Analyte Spiking Technique), the percent R must be...

  6. 30 CFR 75.333 - Ventilation controls.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...), 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959; http://www.astm.org. This....astm.org. This incorporation by reference was approved by the Director of the Federal Register in... Conshohocken, PA 19428-2959; http://www.astm.org. This incorporation by reference was approved by the Director...

  7. Effects of Spray Mixtures on Droplet Size Under Aerial Application Conditions and Implications on Drift

    DTIC Science & Technology

    2010-01-01

    Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light‐Scattering Instruments (ASTM Standards, 2003). The most common term used to...using optical nonimaging light‐scattering instruments. West Conshohocken, Pa.: ASTM Intl. ASTM Standards. 2004. E 1620. Standard terminology relating

  8. Effects of Water Hardness on Spray Droplet Size Under Aerial Application Conditions

    DTIC Science & Technology

    2008-01-01

    Nonimaging Light‐Scattering Instruments (ASTM, 2003). Table 1. Spray formulations for water hardness levels. Hardness (ppm) Tank, L (gal) Kocide, kg (lb...characteristics in a spray using optical nonimaging light‐scattering instruments. W. Conshohocken, Pa.: ASTM Intl. ASTM. 2004. E1620‐97. Standard

  9. Collection Efficiencies of Various Airborne Spray Flux Samplers Used in Aerial Application Research

    DTIC Science & Technology

    2008-01-01

    provided by ASTM Standard E1260: Standard Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light...Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments,” Annual Book of ASTM Stan- dards, ASTM International, West

  10. 46 CFR 56.01-2 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ...-675 (1998), Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties...-1; (40) ASTM A 575-96, Standard Specification for Steel Bars, Carbon, Merchant Quality, M-Grades...-Wrought, Special Quality (“ASTM A 576”), 56.60-2; (42) ASTM B 16-92, Standard Specification for Free...

  11. 30 CFR 75.1900 - Definitions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... for Testing Materials (ASTM), 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA, 19428-2959...

  12. 40 CFR 52.742 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... from the American Society for Testing and Materials (ASTM), 1916 Race Street, Philadelphia, PA 19103. (1) ASTM D1475-85, Standard Test Method for Density of Paint, Varnish, Lacquer, and Related Products, for § 52.741(a)(4)(i)(B)(3)(i). (2) ASTM D2369-87, Standard Test Method for Volatile Content of...

  13. 46 CFR 160.174-3 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... by reference in this subpart are: American Society for Testing and Materials (ASTM) 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM C 177-85 (1993), Standard Test Method for Steady-State...—160.174-17 ASTM C 518-91, Standard Test Method for Steady-State Heat Flux Measurements and Thermal...

  14. 40 CFR 72.13 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... and Material (ASTM), 1916 Race Street, Philadelphia, Pennsylvania 19103; and the University Microfilms International 300 North Zeeb Road, Ann Arbor, Michigan 48106. (1) ASTM D388-92, Standard Classification of Coals by Rank for § 72.2 of this chapter. (2) ASTM D396-90a, Standard Specification for Fuel Oils, for § 72...

  15. 40 CFR 89.6 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... set forth the material that has been incorporated by reference in this part. (1) ASTM material. The... 19428-2959. Document number and name 40 CFR part 89 reference ASTM D86-97: “Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure” Appendix A to Subpart D. ASTM D93-97: “Standard...

  16. 78 FR 77574 - Safety Standard for Bassinets and Cradles; Correction

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-24

    ... cradles that incorporates by reference ASTM F2194-13, with certain modifications. The Commission is correcting two references to sections of ASTM F2194-13. DATES: Effective on April 23, 2014. FOR FURTHER... incorporates by reference ASTM F2194-13, with certain modifications. In FR Doc. 2013- 24023, appearing on page...

  17. PROPOSED ASTM METHOD FOR THE DETERMINATION OF ASBESTOS IN AIR BY TEM AND INFORMATION ON INTERFERING FIBERS

    EPA Science Inventory

    The draft of the ASTM Test Method for air entitled: "Airborne Asbestos Concentration in Ambient and Indoor Atmospheres as Determined by Transmission Electron Microscopy Direct Transfer (TEM)" (ASTM Z7077Z) is an adaptation of the International Standard, ISO 10312. It is currently...

  18. 40 CFR 80.8 - Sampling methods for gasoline and diesel fuel.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... applicable procedures specified in American Society for Testing and Materials (ASTM) method D 4057-95(2000... applicable procedures specified in ASTM method D 4177-95(2000), entitled “Standard Practice for Automatic... applicable procedures in ASTM method D 5842-95(2000), entitled “Standard Practice for Sampling and Handling...

  19. Evaluation of the EPA Drift Reduction Technology (DRT) Low-Speed Wind Tunnel Protocol

    DTIC Science & Technology

    2009-01-01

    Characteristics in a Spray Using Optical Nonimaging Light-Scattering by ASTM Int’l (all rights reserved); Thu May 7 10:08:26 EDT 2009 ed/printed by itz...Spray Using Optical Nonimaging Light-Scattering Instruments,” Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 2003. 9

  20. The Effects of Sn Addition on the Microstructure and Surface Properties of Laser Deposited Al-Si-Sn Coatings on ASTM A29 Steel

    NASA Astrophysics Data System (ADS)

    Fatoba, Olawale S.; Akinlabi, Stephen A.; Akinlabi, Esther T.

    2018-03-01

    Aluminium and its alloys have been successful metal materials used for many applications like commodity roles, automotive and vital structural components in aircrafts. A substantial portion of Al-Fe-Si alloy is also used for manufacturing the packaging foils and sheets for common heat exchanger applications. The present research was aimed at studying the morphology and surface analyses of laser deposited Al-Sn-Si coatings on ASTM A29 steel. These Fe-intermetallic compounds influence the material properties during rapid cooling by laser alloying technique and play a crucial role for the material quality. Thus, it is of considerable technological interest to control the morphology and distribution of these phases in order to eliminate the negative effects on microstructure. A 3 kW continuous wave ytterbium laser system (YLS) attached to a KUKA robot which controls the movement of the alloying process was utilized for the fabrication of the coatings at optimum laser parameters. The fabricated coatings were investigated for its hardness and wear resistance performance. The field emission scanning electron microscope equipped with energy dispersive spectroscopy (SEM/EDS) was used to study the morphology of the fabricated coatings and X-ray diffractometer (XRD) for the identification of the phases present in the coatings. The coatings were free of cracks and pores with homogeneous and refined microstructures. The enhanced hardness and wear resistance performance were attributed to metastable intermetallic compounds formed.

  1. Notched bar Izod impact properties of zinc die castings

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Schrems, K.K.; Dogan, O.N.; Goodwin, F.E.

    2007-03-01

    Notched bar Izod impact testing of zinc die cast Alloy 3, Alloy 5, ZA-8, and AcuZinc 5 was performed at five temperatures between -40\\mDC and room temperature in accordance with ASTM E23 for impact testing of metallic materials. A direct comparison between ASTM D256 for impact testing of plastics and ASTM E23 was performed using continuously cast zinc specimens of Alloy 5 and ZA-8 at -40\\mDC and room temperature. There are differences in sample sizes, impact velocity, and striker geometry between the two tests. Bulk zinc tested according to ASTM E23 resulted in higher impact energies at -40\\mDC and lowermore » impact energies at room temperature then did the same alloys when tested according to ASTM D256.« less

  2. Examining the conspicuousness and prominence of two required warnings on OTC pain relievers

    PubMed Central

    Bix, Laura; Bello, Nora M.; Auras, Rafael; Ranger, Jon; Lapinski, Maria K.

    2009-01-01

    The labeling of over-the-counter (OTC) drugs is critical to their safe and effective use, and certain warnings are meant to be read at the point of purchase (POP). Examples include (i) warnings that alert consumers to the fact that the package is not child-resistant and (ii) warnings that alert consumers to potential product tampering. U.S. law mandates these warnings be “conspicuous” and “prominent” so that it is likely that consumers will read them before leaving the store. Our objective was to quantify the relative prominence and conspicuousness of these warnings. Sixty-one participants reviewed the packages of 5 commercially available analgesics to evaluate the prominence and conspicuousness of these warnings. Evaluated data included (i) the time spent examining the warnings compared with other areas of the label (using a bright pupil eye tracker), (ii) the ability to recall information from the OTCs viewed, and (iii) the legibility of the warnings relative to other elements of the labels (as measured by ASTM D7298-06). Eye-tracking data indicated that warnings were viewed by fewer participants and for less time than other elements of the packages. Recall and legibility data also indicated that the warning statements compared unfavorably with other elements of the labels tested. Evidence presented in this study suggests that 2 required warnings on 5 different OTCs are not prominent or conspicuous when compared with other elements of tested labels. PMID:19332798

  3. Ocean Engineering Studies. Volume 1. Acrylic Submersibles

    DTIC Science & Technology

    1990-04-01

    2.3 ASTM-DIO03-61 Heat distortion temperature +3.60F/minute at 264 psi 200OF: ASTM-0648-56 +3.60F/minute at 66 psi 220OF ASTM-0648-56 Thermal...of Revolution with Axisymmetric Pressures, Temperatures, and Distributed Loads", WAPD -TM-398, December 1963. 4. Stachiw, J. D., Mack, K. L., "The...at 264 psi 200°F +3.6°F/min at 66 psi 220°F Thermal expansion/°F at 20°F 35 x 10-6 Fed. Stan. 406 Method 2031 Water absorpt,.on; 1/8 inch ASTM-D570

  4. Propulsion and Power Rapid Response Research and Development Support. Delivery Order 0042: Demonstration and Evaluation of Fischer-Tropsch Research Fuels for the DoD Assured Fuels Program

    DTIC Science & Technology

    2006-12-01

    7 Figure 3.1-3. Net Heat of Combustion ...No. 1 Aromatic Carbon, max ASTM D-5292 Mol % < 0.5 Sulfur, Total, Max ASTM D-5453 ppm 1 Cetane Index ASTM D-976 Report Net Heat of Combustion , min ASTM...12 /2 00 6 8/ 19 /2 00 6 8/ 26 /2 00 6 9/ 2/ 20 06 8 Figure 3.1-3. Net Heat of Combustion Trend Figure 3.1-4. Freezing Point Trend Net

  5. The oxygen sensitivity/compatibility ranking of several materials by different test methods

    NASA Technical Reports Server (NTRS)

    Lockhart, Billy J.; Bryan, Coleman J.; Hampton, Michael D.

    1989-01-01

    Eleven materials were evaluated for oxygen compatibility using the following test methods: heat of combustion (ASTM D 2015), liquid oxygen impact (ASTM D 2512), pneumatic impact (ASTM G 74), gaseous mechanical impact (ASTM G 86), autogenous ignition temperature by pressurized differential scanning calorimeter, and the determination of the 50 percent reaction level in liquid oxygen using silicon carbide as a reaction enhancer. The eleven materials evaluated were: Teflon TFE, Vespel SP-21, Krytox 240AC, Viton PLV5010B, Fluorel E2160, Kel F 81, Fluorogold, Fluorogreen E-600, Rulon A, Garlock 8573, nylon 6/6.

  6. Effect on moisture permeability of typewriting on unit dose package surfaces.

    PubMed

    Rackson, J T; Zellhofer, M J; Birmingham, P H

    1984-10-01

    The effects of typewriting on labels of two unit dose packages with respect to moisture permeability were examined. Using an electric typewriter, a standard label format was imprinted on two different types of class A unit dose packages: (1) a heat-sealed paper-backed foil and cellofilm strip pouch, and (2) a copolyester and polyethylene multiple-cup blister with a heat-sealed paper-backed foil and cellofilm cover. The labels were typed at various typing-element impact settings. The official USP test for water permeation was then performed on typed packages and untyped control packages. The original untyped packages were confirmed to be USP class A quality. The packages for which successively harder impact settings were used showed a corresponding increase in moisture permeability. This resulted in a lowering of USP package ratings from class A to class B and D, some of which would be unsuitable for use in any unit dose system under current FDA repackaging standards. Typing directly onto the label of a unit dose package before it is sealed will most likely damage the package and possibly make it unfit for use. Pharmacists who must type labels for the unit dose packages studied should use the lowest possible typewriter impact setting and test for damage using the USP moisture-permeation test.

  7. Evaluation of fly ash in water reduced paving mixtures.

    DOT National Transportation Integrated Search

    1985-06-01

    Fly ash was used to replace 15% of the cement in C3WR and C6WR concrete : paving mixes containing ASTM C494 Type A water reducin9 admixtures. Two Class : C ashes and one Class F ash from Iowa approved sources were examined in each : mix. When Class C...

  8. 16 CFR 460.5 - R-value tests.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... INSULATION 460.5 R-value tests. R-value measures resistance to heat flow. R-values given in labels, fact...) All types of insulation except aluminum foil must be tested with ASTM C 177-04, “Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded...

  9. 16 CFR 460.5 - R-value tests.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... INSULATION 460.5 R-value tests. R-value measures resistance to heat flow. R-values given in labels, fact...) All types of insulation except aluminum foil must be tested with ASTM C 177-04, “Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded...

  10. 16 CFR 460.5 - R-value tests.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... INSULATION 460.5 R-value tests. R-value measures resistance to heat flow. R-values given in labels, fact...) All types of insulation except aluminum foil must be tested with ASTM C 177-04, “Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded...

  11. 16 CFR 460.5 - R-value tests.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... INSULATION 460.5 R-value tests. R-value measures resistance to heat flow. R-values given in labels, fact...) All types of insulation except aluminum foil must be tested with ASTM C 177-04, “Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded...

  12. 16 CFR 460.5 - R-value tests.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... INSULATION 460.5 R-value tests. R-value measures resistance to heat flow. R-values given in labels, fact...) All types of insulation except aluminum foil must be tested with ASTM C 177-04, “Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded...

  13. Source emission and model evaluation of formaldehyde from baby furniture in the full scale chamber

    EPA Science Inventory

    This paper describes the measurement and model evaluation of formaldehyde source emissions from composite and solid wood furniture in a full-scale chamber at different ventilation rates for up to 4000 h using ASTM D 6670-01 (2007). Tests were performed on four types of furniture ...

  14. Source emission and model evaluation of formaldehyde from composite and solid wood furniture in a full-scale chamber

    EPA Science Inventory

    This paper describes the measurement and model evaluation of formaldehyde source emissions from composite and solid wood furniture in a full-scale chamber under dynamic conditions using ASTM D 6670-01 (2007). Four brands of the same type furniture product were tested. The data we...

  15. The effect of aggregate type and mix design on the wet skid resistance of bituminous pavement : recommendations for Virginia's Wet Accident Reduction Program.

    DOT National Transportation Integrated Search

    1995-01-01

    This report (1) identified and characterized Virginia's nonpolishing aggregates in terms of their wet skid resistance, (2) compared the standard ASTM E 274-90 skid test to the British Accelerated Polishing Machine (BAPM) and British PendulumTester (B...

  16. Mechanical strength of [HA/Bioplastic/Sericin] composite part printed by bioprinter

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tontowi, Alva Edy, E-mail: alvaedytontowi@ugm.ac.id; Setiawan, Agris

    The aim of this research was to determine the effect of hydroxyapatite (HA) content in printed biocomposite to its mechanical strength. The biocomposite paste was prepared by composing HA, bioplastic and sericin with various ratios of [HA/Bioplastic]: 40/60, 50/50, 60,40 and 70/30. Sericin of 0.3% weight was added to the biocomposite. Mechanical test was conducted to observe tensile (ASTM D 638 type 4) and flexural strength (ASTM D 790). Both type of specimens were fabricated using 3D Printer. Printing process parameter (infill speed, print speed and layer height) were set up as 60 mm/s, 10 mm/s, 0.35 mm, respectively. Resultsmore » showed that biocomposite with [HA/Biplastic]. weight ratio of 60/40(w/w) has an optimum tensile (3.89 ± 1.26 MPa) and flexural strength (2.51 ± 0.45 MPa). Scanning electron microscope observation indicated that microstructure of specimen was influenced by the percentage of the hydroxyapatite. There was no agglomeration of HA particle within the composite.« less

  17. 75 FR 43107 - Full-Size and Non-Full Size Baby Cribs: Withdrawal of Advance Notice of Proposed Rulemaking

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-23

    ... worked with the voluntary standards group, ASTM International (formerly known as the American Society for Testing and Materials), which added provisions in its standard for full-size baby cribs, ASTM F 1169, to... the same as voluntary standards ASTM F 1169-10, Standard Consumer Safety Specification for Full-Size...

  18. 16 CFR 460.7 - Which test version to use.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... HOME INSULATION § 460.7 Which test version to use. Use the version of the ASTM test method that was in effect when this regulation was promulgated. If ASTM changes a test method, the new version will automatically replace the old one in these rules 90 days after ASTM first publishes the change. However, the...

  19. 49 CFR 173.120 - Class 3-Definitions.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Closed Cup Tester, (ASTM D 56) (IBR; see § 171.7 of this subchapter); (B) Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus, (ASTM D 3278) (IBR; see § 171.7 of this subchapter... for Flash Point by Pensky-Martens Closed Cup Tester, (ASTM D 93) (IBR; see § 171.7 of this subchapter...

  20. 40 CFR 761.19 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Products (General Bomb Method) § 761.71(b)(2)(vi) ASTM D 240-87 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuel by Bomb Calorimeter § 761.71(b)(2)(vi) ASTM D 482-87 Standard Test Method... in New and Used Petroleum Products (Bomb Method) § 761.71(b)(2)(vi) ASTM D 923-86 Standard Test...

  1. 24 CFR 200.946 - Building product standards and certification program for exterior finish and insulation systems...

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ...) ASTM C-1186-91 Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets. (v) ASTM D 579-90 Standard Specification for Greige Woven Glass Fabrics. (vi) ASTM D 3273-86—(Reapproved 1991) Standard Test... Glass Fiber Reinforcing Mesh for Use in Exterior Insulation and Finish Systems (EIFS), Class PB. (xv...

  2. 24 CFR 200.946 - Building product standards and certification program for exterior finish and insulation systems...

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ...) ASTM C-1186-91 Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets. (v) ASTM D 579-90 Standard Specification for Greige Woven Glass Fabrics. (vi) ASTM D 3273-86—(Reapproved 1991) Standard Test... Glass Fiber Reinforcing Mesh for Use in Exterior Insulation and Finish Systems (EIFS), Class PB. (xv...

  3. 24 CFR 200.946 - Building product standards and certification program for exterior finish and insulation systems...

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ...) ASTM C-1186-91 Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets. (v) ASTM D 579-90 Standard Specification for Greige Woven Glass Fabrics. (vi) ASTM D 3273-86—(Reapproved 1991) Standard Test... Glass Fiber Reinforcing Mesh for Use in Exterior Insulation and Finish Systems (EIFS), Class PB. (xv...

  4. 40 CFR 61.270 - Applicability and designation of sources.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... for Benzene Emissions From Benzene Storage Vessels § 61.270 Applicability and designation of sources. (a) The source to which this subpart applies is each storage vessel that is storing benzene having a... Benzene, ASTM D835-85 for Refined Benzene-485, ASTM D2359-85a or 93 for Refined Benzene-535, and ASTM...

  5. 40 CFR 61.270 - Applicability and designation of sources.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... for Benzene Emissions From Benzene Storage Vessels § 61.270 Applicability and designation of sources. (a) The source to which this subpart applies is each storage vessel that is storing benzene having a... Benzene, ASTM D835-85 for Refined Benzene-485, ASTM D2359-85a or 93 for Refined Benzene-535, and ASTM...

  6. 40 CFR 61.270 - Applicability and designation of sources.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... for Benzene Emissions From Benzene Storage Vessels § 61.270 Applicability and designation of sources. (a) The source to which this subpart applies is each storage vessel that is storing benzene having a... Benzene, ASTM D835-85 for Refined Benzene-485, ASTM D2359-85a or 93 for Refined Benzene-535, and ASTM...

  7. 40 CFR 61.270 - Applicability and designation of sources.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... for Benzene Emissions From Benzene Storage Vessels § 61.270 Applicability and designation of sources. (a) The source to which this subpart applies is each storage vessel that is storing benzene having a... Benzene, ASTM D835-85 for Refined Benzene-485, ASTM D2359-85a or 93 for Refined Benzene-535, and ASTM...

  8. 40 CFR 61.270 - Applicability and designation of sources.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... for Benzene Emissions From Benzene Storage Vessels § 61.270 Applicability and designation of sources. (a) The source to which this subpart applies is each storage vessel that is storing benzene having a... Benzene, ASTM D835-85 for Refined Benzene-485, ASTM D2359-85a or 93 for Refined Benzene-535, and ASTM...

  9. Organic filler from golden apple snails shells to improve the silicone rubber insulator properties

    NASA Astrophysics Data System (ADS)

    Tepsila, Sujirat; Suksri, Amnart

    2018-02-01

    This paper investigates the effect of an addition of filler compound using golden apple snail shell as an organic filler to the silicone rubber insulator. The filler obtained from golden apple snail shell is found mostly contained calcium carbonate. The organic calcium carbonate (CaCO3) with particle size of 45, 75, 100 and 300 micron were prepared. Sample of silicone rubber that were filled with fillers were tested under ASTM D638-02a type standard for mechanical test. Also, electrical test such as I-V characteristics (ASTM D257-07) and dry arc test according to ASTM D495-14 have been performed. The results revealed that using larger particle size of organic filler obtained from the golden apple snail shell resulted to higher value of dielectric constant as well as higher dielectric strength. Also, the filler helps slow down the tracking activity at an insulator surface due to its crystals of calcium carbonate. However, when using excessive amount of filler, the sample will have a drawbacks in mechanical properties. By using agriculture waste as a filler compound, one can reduced the usage of commercial CaCO3 as an inorganic materials and to lower the investment cost to a final silicone rubber product.

  10. Properties of Concrete with Tire Derived Aggregate Partially Replacing Coarse Aggregates.

    PubMed

    Siringi, Gideon; Abolmaali, Ali; Aswath, Pranesh B

    2015-01-01

    Tire derived aggregate (TDA) has been proposed as a possible lightweight replacement for mineral aggregate in concrete. The role played by the amount of TDA replacing coarse aggregate as well as different treatment and additives in concrete on its properties is examined. Conventional concrete (without TDA) and concrete containing TDA are compared by examining their compressive strength based on ASTM C39, workability based on ASTM C143, splitting tensile strength based on ASTM C496, modulus of rupture (flexural strength) based on ASTM C78, and bond stress based on ASTM C234. Results indicate that while replacement of coarse aggregates with TDA results in reduction in strength, it may be mitigated with addition of silica fume to obtain the desired strength. The greatest benefit of using TDA is in the development of a higher ductile product while utilizing recycled TDA.

  11. Properties of Concrete with Tire Derived Aggregate Partially Replacing Coarse Aggregates

    PubMed Central

    Siringi, Gideon; Abolmaali, Ali; Aswath, Pranesh B.

    2015-01-01

    Tire derived aggregate (TDA) has been proposed as a possible lightweight replacement for mineral aggregate in concrete. The role played by the amount of TDA replacing coarse aggregate as well as different treatment and additives in concrete on its properties is examined. Conventional concrete (without TDA) and concrete containing TDA are compared by examining their compressive strength based on ASTM C39, workability based on ASTM C143, splitting tensile strength based on ASTM C496, modulus of rupture (flexural strength) based on ASTM C78, and bond stress based on ASTM C234. Results indicate that while replacement of coarse aggregates with TDA results in reduction in strength, it may be mitigated with addition of silica fume to obtain the desired strength. The greatest benefit of using TDA is in the development of a higher ductile product while utilizing recycled TDA. PMID:26161440

  12. 49 CFR 172.102 - Special provisions.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... design type that has passed a leakproofness test at the Packing Group II level. Small inner packagings... packaging or transport unit is closed. Each packaging must correspond to a design type that has passed a... transport unit is closed. Each packaging must correspond to a design type that has passed a leakproofness...

  13. 49 CFR 172.102 - Special provisions.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... packaging must correspond to a design type that has passed a leakproofness test at the Packing Group II... packaging must correspond to a design type that has passed a leakproofness test at the Packing Group II... packagings, each packaging must correspond to a design type that has passed a leakproofness test at the...

  14. 49 CFR 172.102 - Special provisions.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... packaging must correspond to a design type that has passed a leakproofness test at the Packing Group II... packaging must correspond to a design type that has passed a leakproofness test at the Packing Group II... packagings, each packaging must correspond to a design type that has passed a leakproofness test at the...

  15. 49 CFR 172.102 - Special provisions.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... design type that has passed a leakproofness test at the Packing Group II level. Small inner packagings... packaging or transport unit is closed. Each packaging must correspond to a design type that has passed a... transport unit is closed. Each packaging must correspond to a design type that has passed a leakproofness...

  16. 76 FR 27882 - Safety Standard for Toddler Beds

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-13

    ..., must meet the warning requirements specified in section 8 of ASTM F 1169-10, instead of the... toddler bed that can convert from a full-size crib, and has the warning specified in section 8.1.3 of ASTM.... (7) In addition to figure 10 of ASTM F 1821-09, use the following: [FR Doc. C1-2011-9421 Filed 5-12...

  17. 46 CFR 162.027-2 - Design, construction, testing and marking requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... the requirements of ASTM F 1546 (incorporated by reference, see § 162.027-1). (b) All inspections and tests required by ASTM F 1546 (incorporated by reference, see § 162.027-1) must be performed by an... completion of the testing required by ASTM F 1546 (incorporated by reference, see § 162.027-1). [CGD 95-027...

  18. 40 CFR 86.1 - Reference materials.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...) ASTM D1945-91, Standard Test Method for Analysis of Natural Gas by Gas Chromatography, IBR approved for §§ 86.113-94, 86.513-94, 86.1213-94, 86.1313-94. (iii) ASTM D2163-91, Standard Test Method for Analysis... §§ 86.113-94, 86.1213-94, 86.1313-94. (iv) ASTM D2986-95a, Reapproved 1999, Standard Practice for...

  19. 40 CFR 86.1 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) ASTM D1945-91, Standard Test Method for Analysis of Natural Gas by Gas Chromatography, IBR approved for §§ 86.113-94, 86.513-94, 86.1213-94, 86.1313-94. (iii) ASTM D2163-91, Standard Test Method for Analysis... §§ 86.113-94, 86.1213-94, 86.1313-94. (iv) ASTM D2986-95a, Reapproved 1999, Standard Practice for...

  20. 77 FR 10358 - Acceptance of ASTM F963-11 as a Mandatory Consumer Product Safety Standard

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-22

    ... Safety. Pursuant to section 106 of the Consumer Product Safety Improvement Act of 2008, ASTM F963-11 will... INFORMATION: On February 10, 2009, section 106(a) of the Consumer Product Safety Improvement Act of 2008... CONSUMER PRODUCT SAFETY COMMISSION 16 CFR Chapter II Acceptance of ASTM F963-11 as a Mandatory...

  1. Chronic ankle pain and fibrosis successfully treated with a new noninvasive augmented soft tissue mobilization technique (ASTM): a case report.

    PubMed

    Melham, T J; Sevier, T L; Malnofski, M J; Wilson, J K; Helfst, R H

    1998-06-01

    This clinical case report demonstrates the clinical effectiveness of a new form of soft tissue mobilization in the treatment of excessive connective tissue fibrosis (scar tissue) around an athlete's injured ankle. The scar tissue was causing the athlete to have pain with activity, pain on palpation of the ankle, decreased range of motion, and loss of function. Surgery and several months of conventional physical therapy failed to alleviate the athlete's symptoms. As a final resort, augmented soft tissue mobilization (ASTM) was administered. ASTM is an alternative nonsurgical treatment modality that is being researched at Performance Dynamics (Muncip, IN). ASTM is a process that uses ergonomically designed instruments that assist therapists in the rapid localization and effective treatment of areas exhibiting excessive soft tissue fibrosis. This is followed by a stretching and strengthening program. Upon the completion of 6 wk of ASTM therapy, the athlete had no pain and had regained full range of motion and function. This case report is an example of how a noninvasive augmented form of soft tissue mobilization (ASTM) demonstrated impressive clinical results in treating a condition caused by connective tissue fibrosis.

  2. Mass variation effect of teki grass (cyperus rotundus) composite against tensile strength and density

    NASA Astrophysics Data System (ADS)

    Rafiq Yanhar, Muhammad; Haris Nasution, A.

    2018-05-01

    The primary purpose of this study is to determine the tensile strength using ASTM D638 - 02a type IVB and density of teki grass (Cyperus rotundus) composite. The production process is carried out by mass variation of 2 gr, 3 gr, and 4 gr. Hand lay-up method with three repetitions is applied. Teki grass is chosen because it is easy to find and has some advantages biodegradable, harmless to health, available in large quantities, and cost-efficient. The test result showed the largest tensile strength is 21,61 MPa at 2-gram mass fiber. Fiber addition to 3 gram and 4-gram cause tensile strength decreases to 18,51 MPa and 11,65 MPa. It happens because the fibers are random and spread in all directions, so many fibers are undirectional with the tensile force. Beside that fibers addition made matrix volume reduced and a bond between fiber and matrix decreases, finally make fiber unable to hold the tensile force properly. It is recommended to use another type of ASTM D638 - 02a which has a larger narrow section like type I (13 mm) and type III (19mm) so specimens are not broken when removed from the mold, and there isn’t any decrease in tensile strength.Density test showed that fiber mass does not significantly affect the density.

  3. Improved estimates of environmental copper release rates from antifouling products.

    PubMed

    Finnie, Alistair A

    2006-01-01

    The US Navy Dome method for measuring copper release rates from antifouling paint in-service on ships' hulls can be considered to be the most reliable indicator of environmental release rates. In this paper, the relationship between the apparent copper release rate and the environmental release rate is established for a number of antifouling coating types using data from a variety of available laboratory, field and calculation methods. Apart from a modified Dome method using panels, all laboratory, field and calculation methods significantly overestimate the environmental release rate of copper from antifouling coatings. The difference is greatest for self-polishing copolymer antifoulings (SPCs) and smallest for certain erodible/ablative antifoulings, where the ASTM/ISO standard and the CEPE calculation method are seen to typically overestimate environmental release rates by factors of about 10 and 4, respectively. Where ASTM/ISO or CEPE copper release rate data are used for environmental risk assessment or regulatory purposes, it is proposed that the release rate values should be divided by a correction factor to enable more reliable generic environmental risk assessments to be made. Using a conservative approach based on a realistic worst case and accounting for experimental uncertainty in the data that are currently available, proposed default correction factors for use with all paint types are 5.4 for the ASTM/ISO method and 2.9 for the CEPE calculation method. Further work is required to expand this data-set and refine the correction factors through correlation of laboratory measured and calculated copper release rates with the direct in situ environmental release rate for different antifouling paints under a range of environmental conditions.

  4. 40 CFR 80.580 - What are the sampling and testing methods for sulfur?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...,000 ppm sulfur standard of § 80.510(k), sulfur content may be determined using ASTM D2622... the 500 ppm sulfur standard of § 80.510(a)(1), sulfur content may be determined using ASTM D2622... to the 1,000 ppm sulfur standard of § 80.510(k), sulfur content may be determined using ASTM D4294...

  5. 40 CFR Table 4 to Subpart Zzzz of... - Requirements for Performance Tests

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... and outlet of the control device; and (1) Portable CO and O2 analyzer. (a) Using ASTM D6522-00 (2005... control device (1) Portable CO and O2 analyzer. (a) Using ASTM D6522-00 (2005) a,b (incorporated by..., appendix A, or ASTM Method D6522-00 (2005) (a) Measurements to determine O2 concentration must be made at...

  6. Comparison of ASTM D613 and ASTM D6890

    DTIC Science & Technology

    2016-04-01

    product , process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement...state or reflect those of the United States Government or the DoA, and shall not be used for advertising or product endorsement purposes...methylnaphthalene proved to be an impractical material for reference values. The ASTM Diesel National Exchange Group ran a study and determined that

  7. 75 FR 61148 - Food and Drug Administration Modernization Act of 1997: Modifications to the List of Recognized...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-04

    ... Evaluation and testing within a risk management process 2-100 ASTM E1372-95 (2003) Standard Test Method...) Standard Title, Type of Test Method for Agar Diffusion Cell standard , Relevant Culture Screening for... Biological evaluation of medical devices - Office(s) and Part 3: Tests for genotoxicity, Division(s...

  8. 26 CFR 48.4081-1 - Taxable fuel; definitions.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... product other than finished gasoline. Kerosene means any liquid that meets the specifications for kerosene... in § 48.4082-1(b). A liquid meets the specifications for kerosene if it is one of the two grades of kerosene (No. 1-K and No. 2-K) covered by ASTM specification D 3699, or kerosene-type jet fuel covered by...

  9. 26 CFR 48.4081-1 - Taxable fuel; definitions.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... product other than finished gasoline. Kerosene means any liquid that meets the specifications for kerosene... in § 48.4082-1(b). A liquid meets the specifications for kerosene if it is one of the two grades of kerosene (No. 1-K and No. 2-K) covered by ASTM specification D 3699, or kerosene-type jet fuel covered by...

  10. Assessment of Quality Assurance Measures for Radioactive Material Transport Packages not Requiring Competent Authority Design Approval - 13282

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Komann, Steffen; Groeke, Carsten; Droste, Bernhard

    The majority of transports of radioactive materials are carried out in packages which don't need a package design approval by a competent authority. Low-active radioactive materials are transported in such packages e.g. in the medical and pharmaceutical industry and in the nuclear industry as well. Decommissioning of NPP's leads to a strong demand for packages to transport low and middle active radioactive waste. According to IAEA regulations the 'non-competent authority approved package types' are the Excepted Packages and the Industrial Packages of Type IP-1, IP-2 and IP-3 and packages of Type A. For these types of packages an assessment bymore » the competent authority is required for the quality assurance measures for the design, manufacture, testing, documentation, use, maintenance and inspection (IAEA SSR 6, Chap. 306). In general a compliance audit of the manufacturer of the packaging is required during this assessment procedure. Their regulatory level in the IAEA regulations is not comparable with the 'regulatory density' for packages requiring competent authority package design approval. Practices in different countries lead to different approaches within the assessment of the quality assurance measures in the management system as well as in the quality assurance program of a special package design. To use the package or packaging in a safe manner and in compliance with the regulations a management system for each phase of the life of the package or packaging is necessary. The relevant IAEA-SSR6 chap. 801 requires documentary verification by the consignor concerning package compliance with the requirements. (authors)« less

  11. Long-Term Corrosion Fatigue of Welded Marine Steels.

    DTIC Science & Technology

    1984-01-01

    MPa ksi MPa I C API 5L Grade B 35 240 60 min. 415 mrin. ASTM A53 Grade B 35 240 60 min. 415 min. ASTM A135 Grade B 35 240 60 min. 415 min. ASTM A139...2% max. cold expansion 42 290 60 min. 415 min. API 5LX Grade X52 2% max. cold expansion 52 360 66 min. 455 min. ASTM AS00 Grade B 42-46 290-320 58 mi...Environments 3.38 " 3.5 Influence of Load Ratio on the Corrosion Fatigue Crack Growth Rates in API X-70 Linepipe Steel in 3.5% NaCl (From (3.30]) 3.39 3.6

  12. The electrical conductivities of candidate beam-waveguide antenna shroud materials

    NASA Technical Reports Server (NTRS)

    Otoshi, T. Y.; Franco, M. M.

    1994-01-01

    The shroud on the beam-waveguide (BWG) antenna at DSS 13 is made from highly magnetic American Society for Testing and Materials (ASTM) A36 steel. Measurements at 8.42 GHz showed that this material (with paint) has a very poor electrical conductivity that is 600 times worse than aluminum. In cases where the BWG mirrors might be slightly misaligned, unintentional illumination and poor electrical conductivity of the shroud walls can cause system noise temperature to be increased significantly. This potential increase of noise temperature contribution can be reduced through the use of better conductivity materials for the shroud walls. An alternative is to attempt to improve the conductivity of the currently used ASTM A36 steel by means of some type of plating, surface treatment, or high-conductivity paints. This article presents the results of a study made to find improved materials for future shrouds and mirror supports.

  13. Diffusion and solubility coefficients determined by permeation and immersion experiments for organic solvents in HDPE geomembrane.

    PubMed

    Chao, Keh-Ping; Wang, Ping; Wang, Ya-Ting

    2007-04-02

    The chemical resistance of eight organic solvents in high density polyethylene (HDPE) geomembrane has been investigated using the ASTM F739 permeation method and the immersion test at different temperatures. The diffusion of the experimental organic solvents in HDPE geomembrane was non-Fickian kinetic, and the solubility coefficients can be consistent with the solubility parameter theory. The diffusion coefficients and solubility coefficients determined by the ASTM F739 method were significantly correlated to the immersion tests (p<0.001). The steady state permeation rates also showed a good agreement between ASTM F739 and immersion experiments (r(2)=0.973, p<0.001). Using a one-dimensional diffusion equation based on Fick's second law, the diffusion and solubility coefficients obtained by immersion test resulted in over estimates of the ASTM F739 permeation results. The modeling results indicated that the diffusion and solubility coefficients should be obtained using ASTM F739 method which closely simulates the practical application of HDPE as barriers in the field.

  14. 40 CFR 799.5089 - Chemical testing requirements for third group of high production volume chemicals (HPV3).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 2007). 2. Acute Toxicity to Daphnia: ASTM E 729-96 (Reapproved 2007). 3. Toxicity to Plants (Algae...). 2. Toxicity to Plants (Algae): ASTM E 1218-04 e1 The following are the special conditions for C1, C2... (Reapproved 2007). 2. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity...

  15. 40 CFR 799.5089 - Chemical testing requirements for third group of high production volume chemicals (HPV3).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 2007). 2. Acute Toxicity to Daphnia: ASTM E 729-96 (Reapproved 2007). 3. Toxicity to Plants (Algae...). 2. Toxicity to Plants (Algae): ASTM E 1218-04 e1 The following are the special conditions for C1, C2... (Reapproved 2007). 2. Toxicity to Plants (Algae): ASTM E 1218-04 e1 Test Group 2 for C2: 1. Chronic Toxicity...

  16. 40 CFR 1065.703 - Distillate diesel fuel.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 1 Cetane Number 40-50 40-50 40-50 ASTM D613-05. Distillation range: Initial boiling point °C 171-204 171-204 171-204 ASTM D86-07a. 10 pct. point 204-238 204-238 204-238 50 pct. point 243-282 243-282 243...-37 ASTM D4052-96e01. Total sulfur, ultra low sulfur mg/kg 7-15 See 40 CFR 80.580. Total sulfur, low...

  17. 49 CFR 179.102-1 - Carbon dioxide, refrigerated liquid.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... and anchorage of tanks must be made of carbon steel conforming to ASTM A 516/A 516M (IBR, see § 171.7 of this subchapter), Grades 55, 60, 65, or 70, or AAR Specification TC 128-78, Grade B. The ASTM A 516/A 516M plate must also meet the Charpy V-Notch test requirements of ASTM A 20/A 20M (see table 16...

  18. 40 CFR Table 5 to Subpart Uuuuu of... - Performance Testing Requirements

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... to ASTM D6348-03, Sections A1 through A8 are mandatory; (2) For ASTM D6348-03 Annex A5 (Analyte Spiking Technique), the percent (%) R must be determined for each target analyte (see Equation A5.5); (3) For the ASTM D6348-03 test data to be acceptable for a target analyte, %R must be 70% ≥ R ≤ 130%; and...

  19. 40 CFR Table 5 to Subpart Uuuuu of... - Performance Testing Requirements

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... to ASTM D6348-03, Sections A1 through A8 are mandatory; (2) For ASTM D6348-03 Annex A5 (Analyte Spiking Technique), the percent (%)R must be determined for each target analyte (see Equation A5.5); (3) For the ASTM D6348-03 test data to be acceptable for a target analyte, %R must be 70% ≤R ≤130%; and (4...

  20. 40 CFR Table 5 to Subpart Uuuuu of... - Performance Testing Requirements

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... to ASTM D6348-03, Sections A1 through A8 are mandatory; (2) For ASTM D6348-03 Annex A5 (Analyte Spiking Technique), the percent (%)R must be determined for each target analyte (see Equation A5.5); (3) For the ASTM D6348-03 test data to be acceptable for a target analyte, %R must be 70%≤ R ≤ 130%; and...

  1. Adulteration of diesel/biodiesel blends by vegetable oil as determined by Fourier transform (FT) near infrared spectrometry and FT-Raman spectroscopy.

    PubMed

    Oliveira, Flavia C C; Brandão, Christian R R; Ramalho, Hugo F; da Costa, Leonardo A F; Suarez, Paulo A Z; Rubim, Joel C

    2007-03-28

    In this work it has been shown that the routine ASTM methods (ASTM 4052, ASTM D 445, ASTM D 4737, ASTM D 93, and ASTM D 86) recommended by the ANP (the Brazilian National Agency for Petroleum, Natural Gas and Biofuels) to determine the quality of diesel/biodiesel blends are not suitable to prevent the adulteration of B2 or B5 blends with vegetable oils. Considering the previous and actual problems with fuel adulterations in Brazil, we have investigated the application of vibrational spectroscopy (Fourier transform (FT) near infrared spectrometry and FT-Raman) to identify adulterations of B2 and B5 blends with vegetable oils. Partial least square regression (PLS), principal component regression (PCR), and artificial neural network (ANN) calibration models were designed and their relative performances were evaluated by external validation using the F-test. The PCR, PLS, and ANN calibration models based on the Fourier transform (FT) near infrared spectrometry and FT-Raman spectroscopy were designed using 120 samples. Other 62 samples were used in the validation and external validation, for a total of 182 samples. The results have shown that among the designed calibration models, the ANN/FT-Raman presented the best accuracy (0.028%, w/w) for samples used in the external validation.

  2. Brain activity is related to individual differences in the number of items stored in auditory short-term memory for pitch: evidence from magnetoencephalography.

    PubMed

    Grimault, Stephan; Nolden, Sophie; Lefebvre, Christine; Vachon, François; Hyde, Krista; Peretz, Isabelle; Zatorre, Robert; Robitaille, Nicolas; Jolicoeur, Pierre

    2014-07-01

    We used magnetoencephalography (MEG) to examine brain activity related to the maintenance of non-verbal pitch information in auditory short-term memory (ASTM). We focused on brain activity that increased with the number of items effectively held in memory by the participants during the retention interval of an auditory memory task. We used very simple acoustic materials (i.e., pure tones that varied in pitch) that minimized activation from non-ASTM related systems. MEG revealed neural activity in frontal, temporal, and parietal cortices that increased with a greater number of items effectively held in memory by the participants during the maintenance of pitch representations in ASTM. The present results reinforce the functional role of frontal and temporal cortices in the retention of pitch information in ASTM. This is the first MEG study to provide both fine spatial localization and temporal resolution on the neural mechanisms of non-verbal ASTM for pitch in relation to individual differences in the capacity of ASTM. This research contributes to a comprehensive understanding of the mechanisms mediating the representation and maintenance of basic non-verbal auditory features in the human brain. Copyright © 2014 Elsevier Inc. All rights reserved.

  3. Permeation of 70% isopropyl alcohol through surgical gloves: comparison of the standard methods ASTM F739 and EN 374.

    PubMed

    Mäkelä, Erja A; Vainiotalo, Sinikka; Peltonen, Kimmo

    2003-06-01

    Standard test methods ASTM F739 and EN 374 were compared by assessing the permeation of 70% isopropyl alcohol (2-propanol) through seven brands of surgical gloves. The two standards differ in the flow rates of the collection medium and in the chemical permeation rate at which the breakthrough time (BTT) is detected, the EN detection level being 10 times higher than the permeation rate used by ASTM. In a departure from the EN standard method, a 4 h testing time was used instead of 8 h. All of the tested gloves were from the same manufacturer and were made from either natural rubber (NR) (six brands) or chloroprene rubber (CR) (one brand). Two of the NR glove brands were double layered. For the thin NR gloves (0.22, 0.28 and 0.27 mm) the permeation rates were higher throughout the tests with a flow rate of 474 ml/min (EN) of the collection medium (nitrogen) compared with the permeation rates obtained with a flow rate of 52 ml/min (ASTM). These resulted in BTTs of 4.6, 6.5 and 7.6 min (EN) and 4.8, 6.5 and 9.1 min (ASTM), respectively. No statistical difference could be observed between the BTT values obtained with the two standard methods for any of the thin gloves. Thus, although the ASTM standard has a lower criterion for the detection of permeation, it does not necessarily produce shorter BTTs. For the better barriers the methods yielded more equivalent permeation rate curves and thus the EN BTTs were longer than the ASTM BTTs: the EN results were 21, 80, 122 and >240 min compared with the ASTM results of 12, 32, 38 and 103 min for glove thicknesses of 0.37 (NR), 0.22 + 0.22 (double layered NR), 0.31 + 0.29 (double layered NR) and 0.19 mm (CR), respectively.

  4. Stored product mites (Acari: Astigmata) infesting food in various types of packaging.

    PubMed

    Hubert, Jan; Nesvorna, Marta; Volek, Vlado

    2015-02-01

    From 2008 to 2014, stored product mites have been reported from prepackaged dried food on the market in the Czech Republic. The infestation was by Carpoglyphus lactis (L.) in dried fruits and Tyrophagus putrescentiae (Schrank) in dog feed. The infestation is presumably caused by poor protection of the packages. We compared various packaging methods for their resistance to mites using dried apricots and dog feed in laboratory experiments. The trial packages included nine different plastic films, monofilm, duplex and triplex, and one type of plastic cup (ten replicates per packaging type). All packaging materials are available on the Czech market for dried food products. The samples of dried food were professionally packed in a factory and packaged dried apricots were exposed to C. lactis and dog food to T. putrescentiae. After 3 months of exposure, the infestation and mite density of the prepackaged food was assessed. Mites were found to infest six types of packages. Of the packaging types with mites, 1-5 samples were infested and the maximum abundance was 1,900 mites g(-1) of dried food. Mites entered the prepackaged food by faulty sealing. Inadequate sealing is suggested to be the major cause of the emerged infestation of dried food.

  5. Type of oral solid medication packaging and medication preparation time in nursing homes: A direct observation study.

    PubMed

    Cready, C M; Hudson, C; Dreyer, K

    2017-12-01

    Medication administration is a substantial portion of the workday in nursing homes, with the medication preparation step being the most time-consuming. However, little is known about how medication preparation time is affected by the type of packaging used for oral solid medications (ie, tablets/capsules). We examined the effects of two types of packaging. As fewer steps are associated with strip packaging compared to bingo card packaging, we hypothesized that the increase in medication preparation seconds per resident with each additional oral solid medication would be smaller when strip packaging was used. A total of 430 medication preparations conducted by eight nurses during the regularly scheduled morning medication administration period in two nursing homes-using strip packaging and bingo card packaging, respectively-were observed. Each medication preparation observation was matched to its corresponding medication administration record and observations averaged across resident. Using the resident sample (N=149), we estimated three regression models (adjusting the standard errors for the clustering of resident by nurse). The first model regressed medication preparation seconds on the number of oral solid medications. The second model added the type of packaging used and the control variables (type of unit [long-term care, post-acute care], the number of one-half pills and the dosage form diversity in the preparation). To test our hypothesis, the third model added an interaction term between the number of oral solid medications and the type of packaging used. As hypothesized, all else equal, the number of oral solid medications tended to increase medication preparation time per resident in both nursing homes, but the increase was smaller in the strip packaging nursing home (P<.05). Each additional oral solid medication in the bingo card packaging nursing home increased medication preparation by an average of 13 seconds (b=13.077), whereas each oral solid medication administered in the strip packaging nursing home increased medication preparation by an average of only 8 seconds (13.077-5.092=7.985). This is a difference on average of about 5 seconds per oral solid medication. To our knowledge, we were the first to examine the effect of type of oral solid medication packaging on medication preparation time in nursing homes. Type of packaging matters. The time saved using strip packaging (vs bingo card packaging) has implications for quality of care and the movement towards person-centred care in the nursing home sector. Nurses (or other staff tasked with medication preparation) in nursing homes using strip packaging potentially have more time to devote to nurturing a relationship with the resident. However, time saved in medication preparation by strip packaging is counterproductive if a serious error results. Thus, future studies should investigate the effects of type of packaging on medication preparation errors. © 2017 John Wiley & Sons Ltd.

  6. Comparative results of autogenous ignition temperature measurements by ASTM G 72 and pressurized scanning calorimetry in gaseous oxygen

    NASA Technical Reports Server (NTRS)

    Bryan, C. J.; Lowrie, R.

    1986-01-01

    The autogenous ignition temperature of four materials was determined by ASTM (G 72) and pressurized differential scanning calorimetry at 0.68-, 3.4-, and 6.8-MPa oxygen pressure. All four materials were found to ignite at lower temperatures in the ASTM method. The four materials evaluated in this program were Neoprene, Vespel SP-21, Fluorel E-2160, and nylon 6/6.

  7. Flash Point Performance Evaluation

    DTIC Science & Technology

    2014-03-01

    ACRONYMS AND ABBREVIATIONS Acronym Definition ASTM ASTM International, consensus standards and specifications B20 Biodiesel containing 20% FAME...HRJ-1 is a sample of HEFA SPK [10] that is used to blend semi-synthetic jet fuel. The B20-1 is a sample of a 20% biodiesel blend [20]. The US Army...Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20), ASTM International, W. Conshohocken, PA 21. MIL-DTL-25576E the Detail

  8. Army Oil Analysis Program for Vehicle Testing

    DTIC Science & Technology

    1996-08-16

    4 TOP 2-2-690 16 August 1996 (l) Water determination: Karl Fischer method (TM 38-301-2 or ASTM-D1744 3 ): Set up the Karl Fischer titrator in...higher temperature if required. aMagnification. bReflected. CTransmitted. 5. DATA REQUIRED. a. Water: Karl Fischer percent water-- (% H2 0). b...Liquid Petroleum Products by Karl Fischer Reagent, 1984. 4. DL 18, Karl Fischer Titrator Operating Instructions. 5. ASTM-D445, Annual Book of ASTM

  9. 49 CFR 179.400-5 - Materials.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-5 Materials. (a) Stainless steel of ASTM A 240/A 240M (IBR, see § 171.7 of this subchapter), Type 304 or 304L must be used... the lading. (b) Any steel casting, steel forging, steel structural shape or carbon steel plate used to...

  10. 49 CFR 179.400-5 - Materials.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-5 Materials. (a) Stainless steel of ASTM A 240/A 240M (IBR, see § 171.7 of this subchapter), Type 304 or 304L must be used... the lading. (b) Any steel casting, steel forging, steel structural shape or carbon steel plate used to...

  11. 49 CFR 179.400-5 - Materials.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-5 Materials. (a) Stainless steel of ASTM A 240/A 240M (IBR, see § 171.7 of this subchapter), Type 304 or 304L must be used... the lading. (b) Any steel casting, steel forging, steel structural shape or carbon steel plate used to...

  12. 49 CFR 179.400-5 - Materials.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-5 Materials. (a) Stainless steel of ASTM A 240/A 240M (IBR, see § 171.7 of this subchapter), Type 304 or 304L must be used... the lading. (b) Any steel casting, steel forging, steel structural shape or carbon steel plate used to...

  13. 40 CFR 63.5719 - How do I conduct a performance test?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... sampling sites. (2) Use Method 2, 2A, 2C, 2D, 2F or 2G of appendix A to 40 CFR part 60, as appropriate, to... organic HAP emissions. (4) You may use American Society for Testing and Materials (ASTM) D6420-99... respect to the types of parts being made and material application methods. The production conditions...

  14. 40 CFR 63.5719 - How do I conduct a performance test?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... sampling sites. (2) Use Method 2, 2A, 2C, 2D, 2F or 2G of appendix A to 40 CFR part 60, as appropriate, to... organic HAP emissions. (4) You may use American Society for Testing and Materials (ASTM) D6420-99... respect to the types of parts being made and material application methods. The production conditions...

  15. 40 CFR 63.5719 - How do I conduct a performance test?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... sampling sites. (2) Use Method 2, 2A, 2C, 2D, 2F or 2G of appendix A to 40 CFR part 60, as appropriate, to... organic HAP emissions. (4) You may use American Society for Testing and Materials (ASTM) D6420-99... respect to the types of parts being made and material application methods. The production conditions...

  16. NIST-NRC Comparison of Total Immersion Liquid-in-Glass Thermometers

    NASA Astrophysics Data System (ADS)

    Hill, K. D.; Gee, D. J.; Cross, C. D.; Strouse, G. F.

    2009-02-01

    The use of liquid-in-glass (LIG) thermometers is described in many documentary standards in the fields of environmental testing, material testing, and material transfer. Many national metrology institutes, including the National Institute of Standards and Technology (NIST) and the National Research Council of Canada (NRC), list calibration services for these thermometers among the Calibration Measurement Capabilities of Appendix C of the BIPM Key Comparison Database. NIST and NRC arranged a bilateral comparison of a set of total-immersion ASTM-type LIG thermometers to validate their uncertainty claims. Two each of ASTM thermometer types 62C through 69C were calibrated at NIST and at NRC at four temperatures distributed over the range appropriate to each thermometer, in addition to the ice point. Collectively, the thermometers span a temperature range of - 38 °C to 305 °C. In total, 160 measurements (80 pairs) comprise the comparison data set. Pair-wise differences ( T NIST- T NRC) were formed for each thermometer at each temperature. For 8 of the 80 pairs (10 %), the differences exceed the k = 2 combined uncertainties. These results support the claimed capabilities of NIST and NRC for the calibration of LIG thermometers.

  17. Effects of cryogenic treatment on the wear properties of brake discs

    NASA Astrophysics Data System (ADS)

    Nadig, D. S.; Shivakumar, P.; Anoop, S.; Chinmay, Kulkarni; Divine, P. V.; Harsha, H. P.

    2017-02-01

    Disc brakes are invariably used in all the automobiles either to reduce the rotational speed of the wheel or to hold the vehicle stationary. During the braking action, the kinetic energy is converted into heat which can result in high temperatures resulting in fading of brake effects. Brake discs produced out of martensite stainless steel (SS410) are expected to exhibit high wear resistance properties with low value of coefficient of friction. These factors increase the useful life of the brake discs with minimal possibilities of brake fade. To study the effects of cryogenic treatment on the wear behaviour, two types of brake discs were cryotreated at 98K for 8 and 24 hours in a specially developed cryotreatment system using liquid nitrogen. Wear properties of the untreated and cryotreated test specimens were experimentally determined using the pin on disc type tribometer (ASTM G99-95). Similarly, the Rockwell hardness (HRC) of the specimens were tested in a hardness tester in accordance with ASTM E18. In this paper, the effects of cryotreatment on the wear and hardness properties of untreated and cryotreated brake discs are presented. Results indicate enhancement of wear properties and hardness after cryogenic treatment compared with the normal brakes discs.

  18. Phosphor chessboard packaging for white LEDs in high efficiency and high color performance

    NASA Astrophysics Data System (ADS)

    Nguyen, Quang-Khoi; Chang, Yu-Yu; Lu, Chun-Yan; Yang, Tsung-Hsun; Chung, Te-Yuan; Sun, Ching-Cherng

    2016-09-01

    We performed the simulation of white LEDs packaging with different chessboard structures of white light converting phosphor layer covered on GaN die chip. Three different types of chessboard structures are called type 1, type 2 and type 3, respectively. The result of investigation according to the phosphor thickness show the increasing of thickness of phosphor layer are, the decreasing of output blue light power are. Meanwhile, the changes of yellow light are neglect. Type 3 shows highest packaging efficiency of 74.3 % compares with packaging efficiency of type 2 and type 1 (72.5 % and 71.3 %, respectively). Type 3 also shows the most effect of forward light. Attention that the type 3 chessboard structure gets packaging efficiency of 74.3 % at color temperature of daylight as well as high saving of phosphor amount. The color temperatures of three types of chessboard structure are higher than 5000 K, so they are suitable for lighting purpose. The angular correlate color temperature deviation (ACCTD) of type 1, type 2 and type 3 are 6500K, 11500K and 17000K, respectively.

  19. Mechanical and Physical Properties of ASTM C33 Sand

    DTIC Science & Technology

    2008-02-01

    ERDC/GSL TR-08-2 7 Grain-size Distribution (1) (ASTM D 422) 1 test run on total sand sample Proctor Density Curves (2) (ASTM D 698 and D... Proctor (Figure 4). Because of the noncohesive nature of the SP material, a series of relative density tests measuring both minimum and maximum... density tests were conducted with moisture added to the sand. A summary of the minimum and maximum densities is given in Table 2. During Proctor

  20. Alternative Fuels Data Center: ASTM Biodiesel Specifications

    Science.gov Websites

    purchased from ASTM International. Property Test Method Grade No.1-B S15 Grade No.1-B S500 Grade No.2-B S15 ASTM International. Property Test Method Grade B6 to B20 S15 B6 to B20 S500 j B6 to B20 S5000 Acid for the intended use and expected ambient temperatures. Test Methods D 4539 and D 6371 may be useful

  1. Automated acid and base number determination of mineral-based lubricants by fourier transform infrared spectroscopy: commercial laboratory evaluation.

    PubMed

    Winterfield, Craig; van de Voort, F R

    2014-12-01

    The Fluid Life Corporation assessed and implemented Fourier transform infrared spectroscopy (FTIR)-based methods using American Society for Testing and Materials (ASTM)-like stoichiometric reactions for determination of acid and base number for in-service mineral-based oils. The basic protocols, quality control procedures, calibration, validation, and performance of these new quantitative methods are assessed. ASTM correspondence is attained using a mixed-mode calibration, using primary reference standards to anchor the calibration, supplemented by representative sample lubricants analyzed by ASTM procedures. A partial least squares calibration is devised by combining primary acid/base reference standards and representative samples, focusing on the main spectral stoichiometric response with chemometrics assisting in accounting for matrix variability. FTIR(AN/BN) methodology is precise, accurate, and free of most interference that affects ASTM D664 and D4739 results. Extensive side-by-side operational runs produced normally distributed differences with mean differences close to zero and standard deviations of 0.18 and 0.26 mg KOH/g, respectively. Statistically, the FTIR methods are a direct match to the ASTM methods, with superior performance in terms of analytical throughput, preparation time, and solvent use. FTIR(AN/BN) analysis is a viable, significant advance for in-service lubricant analysis, providing an economic means of trending samples instead of tedious and expensive conventional ASTM(AN/BN) procedures. © 2014 Society for Laboratory Automation and Screening.

  2. 75 FR 37310 - Engine-Testing Procedures

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-29

    ...: Olefins m\\3\\/m\\3\\....... Maximum, 0.10.... Maximum, 0.175... ASTM D1319-03. Aromatics Maximum, 0.35.... Maximum, 0.304... Saturates Remainder........ Remainder........ * * * * * \\1\\ ASTM procedures are...

  3. A training programme involving automatic self-transcending meditation in late-life depression: preliminary analysis of an ongoing randomised controlled trial.

    PubMed

    Vasudev, Akshya; Arena, Amanda; Burhan, Amer M; Ionson, Emily; Hirjee, Hussein; Maldeniya, Pramudith; Wetmore, Stephen; Newman, Ronnie I

    2016-03-01

    Late-life depression affects 2-6% of seniors aged 60 years and above. Patients are increasingly embracing non-pharmacological therapies, many of which have not been scientifically evaluated. This study aimed to evaluate a category of meditation, automatic self-transcending meditation (ASTM), in alleviating symptoms of depression when augmenting treatment as usual (NCT02149810). The preliminary results of an ongoing single-blind randomised controlled trial comparing a training programme involving ASTM with a wait-list control indicate that a 12-week ASTM programme may lead to significantly greater reductions in depression and anxiety severity. As such, ASTM may be an effective adjunctive therapy in the treatment of late-life depression. R.I.N. is Director of Research and Health Promotion for the Art of Living Foundation, Canada and supervised the staff providing ASTM training. © The Royal College of Psychiatrists 2016. This is an open access article distributed under the terms of the Creative Commons Non-Commercial, No Derivatives (CC BY-NC-ND) licence.

  4. A training programme involving automatic self-transcending meditation in late-life depression: preliminary analysis of an ongoing randomised controlled trial

    PubMed Central

    Arena, Amanda; Burhan, Amer M.; Ionson, Emily; Hirjee, Hussein; Maldeniya, Pramudith; Wetmore, Stephen; Newman, Ronnie I.

    2016-01-01

    Late-life depression affects 2–6% of seniors aged 60 years and above. Patients are increasingly embracing non-pharmacological therapies, many of which have not been scientifically evaluated. This study aimed to evaluate a category of meditation, automatic self-transcending meditation (ASTM), in alleviating symptoms of depression when augmenting treatment as usual (NCT02149810). The preliminary results of an ongoing single-blind randomised controlled trial comparing a training programme involving ASTM with a wait-list control indicate that a 12-week ASTM programme may lead to significantly greater reductions in depression and anxiety severity. As such, ASTM may be an effective adjunctive therapy in the treatment of late-life depression. Declaration of interest R.I.N. is Director of Research and Health Promotion for the Art of Living Foundation, Canada and supervised the staff providing ASTM training. Copyright and usage © The Royal College of Psychiatrists 2016. This is an open access article distributed under the terms of the Creative Commons Non-Commercial, No Derivatives (CC BY-NC-ND) licence. PMID:27703774

  5. Evaluation of acute copper toxicity to juvenile freshwater mussels (fatmucket, lampsilis siliquoidea) in natural and reconstituted waters

    USGS Publications Warehouse

    Wang, N.; Mebane, C.A.; Kunz, J.L.; Ingersoll, C.G.; May, T.W.; Arnold, W.R.; Santore, R.C.; Augspurger, T.; Dwyer, F.J.; Barniiart, M.C.

    2009-01-01

    The influence of dissolved organic carbon (DOC) and water composition on the toxicity of copper to juvenile freshwater mussels (fatmucket, Lampsilis siliquoidea) were evaluated in natural and reconstituted waters. Acute 96-h copper toxicity tests were conducted at four nominal DOC concentrations (0, 2.5, 5, and 10 mg/L as carbon [C]) in dilutions of natural waters and in American Society for Testing and Materials (ASTM) reconstituted hard water. Toxicity tests also were conducted in ASTM soft, moderately hard, hard, and very hard reconstituted waters (nominal hardness 45-300 mg/L as CaCO3). Three natural surface waters (9.5-11 mg/L DOC) were diluted to obtain a series of DOC concentrations with diluted well water, and an extract of natural organic matter and commercial humic acid was mixed with ASTM hard water to prepare a series of DOC concentrations for toxicity testing. Median effective concentrations (EC50s) for dissolved copper varied >40-fold (9.9 to >396 ??g Cu/L) over all 21 treatments in various DOC waters. Within a particular type of DOC water, EC50s increased 5- to 12-fold across DOC concentrations of 0.3 to up to 11 mg C/L. However, EC50s increased by only a factor of 1.4 (21 30 ??g Cu/L) in the four ASTM waters with wide range of water hardness (52-300 mg CaCO 3/L). Predictions from the biotic ligand model (BLM) for copper explained nearly 90% of the variability in EC50s. Nearly 70% of BLM-normalized EC50s for fatmucket tested in natural waters were below the final acute value used to derive the U.S. Environmental Protection Agency acute water quality criterion for copper, indicating that the criterion might not be protective of fatmucket and perhaps other mussel species. ?? 2009 SETAC.

  6. Whole glove permeation of cyclohexanol through disposable nitrile gloves on a dextrous robot hand and comparison with the modified closed-loop ASTM F739 method 1. No fist clenching.

    PubMed

    Mathews, Airek R; Que Hee, Shane S

    2017-04-01

    The aim was to develop a whole glove permeation method for cyclohexanol to generate permeation parameter data for a non-moving dextrous robot hand (normalized breakthrough time t b , standardized breakthrough time t s , steady state permeation rate P s , and diffusion coefficient D). Four types of disposable powderless, unsupported, and unlined nitrile gloves from the same producer were investigated: Safeskin Blue and Kimtech Science Blue, Purple, and Sterling. The whole glove method developed involved a peristaltic pump for water circulation through chemically resistant Viton tubing to continually wash the inner surface of the test glove via holes in the tubing, a dextrous robot hand operated by a microprocessor, a chemically protective nitrile glove to protect the robot hand, an incubator to maintain 35°C temperature, and a hot plate to maintain 35°C at the sampling point of the circulating water. Aliquots of 1.0 mL were sampled at regular time intervals for the first 60 min followed by removal of 0.5 mL aliquots every hour to 8 hr. Quantification was by the internal standard method after gas chromatography-selective ion electron impact mass spectrometry using a non-polar capillary column. The individual glove values of t b and t s differed for the ASTM closed loop method except for Safeskin Blue, but did not for the whole glove method. Most of the kinetic parameters agreed within an order of magnitude for the two techniques. The order of most protective to least protective glove was Blue and Safeskin, then Purple followed by Sterling for the whole gloves. The analogous order for the modified F739 ASTM closed loop method was: Safeskin, Blue, Purple, and Sterling, almost the same as for the whole glove. The Sterling glove was "not recommended" from the modified ASTM data, and was "poor" from the whole glove data.

  7. Overview (this manuscript is an overview of an ASTM symposium. The authors, John Sebroski and Mark Mason, of the overview were the co-chairs of the symposium and co-editors of the manuscripts submitted for ASTM peer review and subsequent publication in the technical proceedings for the symposium)

    EPA Science Inventory

    The Symposium on Developing Consensus Standards for Measuring Chemical Emissions from Spray Polyurethane Foam (SPF) Insulation was held on April 30th and May 1, 2015. Sponsored by ASTM Committee D22 on Air Quality, the symposium was held in Anaheim, CA, in conjunction with the st...

  8. Interim Report on the Investigation of the Fresh Properties of Synthetic Fiber-Reinforced Concrete for the Richardson Landing Casting Field

    DTIC Science & Technology

    2017-04-01

    Figure 2. ASTM (2011) (C40) organic impurities testing of dredged sand. ........................................... 6 Tables Table 1. ASTM (2006) (C136...International (2011) (C40). The ASTM C40 organic impurity color was reported as a 4. Aggregates with this dark of a color may have problems with air...entrainment, freeze thaw durability, and compressive strength due to organic impurities being present in the fine aggregate. Problems with air

  9. 49 CFR 172.102 - Special provisions.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... bags, each packaging must correspond to a design type that has passed a leakproofness test at the... packaging must correspond to a design type that has passed a leakproofness test at the Packing Group II... packaging must correspond to a design type that has passed a leakproofness test at the Packing Group II...

  10. Evaluating Penetration Ability of Plodia interpunctella (Hübner) (Lepidoptera: Pyralidae) Larvae into Multilayer Polypropylene Packages.

    PubMed

    Scheff, Deanna S; Sehgal, Blossom; Subramanyam, Bhadriraju

    2018-04-18

    The larvae of the Indian meal moth, Plodia interpunctella (Hübner), can invade or penetrate packaging materials and infest food products. Energy bars with three polypropylene packaging types were challenged with eggs (first instars), third instars, and fifth instars of P. interpunctella to determine package resistance at 28 °C and 65% r.h. The packing types were also challenged with two male and two female pupae of P. interpunctella under similar conditions in order to determine which package provided the greatest protection against larval penetration. Samples infested with eggs, third instars, and pupae were evaluated after 21 days and 42 days to count the number of larvae, pupae, and adults found inside the packages. Packages challenged with fifth instars were observed after 21 days to count the number of larvae, pupae, and adults inside each package. The number and diameter of the holes were determined in each package, followed by the amount of damage sustained to the energy bar. Third and fifth instars showed a higher tendency to penetrate all of the packaging types. First instars showed a reduction in package penetration ability compared with third and fifth instars. The increase in exposure time resulted in an increase in the damage sustained to the energy bars. Among packaging types, the thickest package (Test A) was most resilient to penetration by all of the larval stages. In conclusion, energy bar manufacturers need to invest more effort into improving packaging designs, creating thicker gauge films, or advancing odor barrier technology, in order to prevent penetration and infestation by P. interpunctella larvae.

  11. Containers and Packaging: Product-Specific Data

    EPA Pesticide Factsheets

    This web page provide numbers on the different containers and packaging products in our municipal solid waste. These include containers of all types, such as glass, steel, plastic, aluminum, wood, and other types of packaging

  12. Test report dot 7A type a liquid packaging

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ketusky, E. T.; Brandjes, C.; Benoit, T. J.

    This test report documents the performance of Savannah River National Laboratory’s (SRNL’s) U.S. Department of Transportation (DOT) Specification 7A; General Packaging, Type A shielded liquid shipping packaging and compliance with the regulatory requirements of Title 49 of the Code of Federal Regulations (CFR). The primary use of this packaging design is for the transport of radioactive liquids of up to 1.3 liters in an unshielded configuration and up to 113 mL of radioactive liquids in a shielded configuration, with no more than an A2 quantity in either configuration, over public highways and/or commercial aircraft. The contents are liquid radioactive materialsmore » sufficiently shielded and within the activity limits specified in173.435 or 173.433 for A2 (normal form) materials, as well as within the analyzed thermal heat limits. Any contents must be compatibly packaged and must be compatible with the packaging. The basic packaging design is based on the U.S. Department of Energy’s (DOE’s) Model 9979 Type A fissile shipping packaging designed and tested by SRNL. The shielded liquid configuration consists of the outer and inner drums of the 9979 package with additional low density polyethylene (LDPE) dunnage nesting a tungsten shielded cask assembly (WSCA) within the 30-gallon inner drum. The packaging model for the DOT Specification 7A, Type A liquids packaging is HVYTAL.« less

  13. Wood particleboard and flakeboard : types, grades, and uses

    Treesearch

    C. G. Carll

    1986-01-01

    This report is for those who use or may want to use wood particleboard. The term bparticleboardc is used as defined in the American Society for Testing and Materials (ASTM) Standard D 1554, which includes flakeboards as a subclass of particleboards, and not as used in the lumber trade where the term is usually reserved for panels made of fine wood particles such as...

  14. Effect of opacifiers and UV absorbers on pigmented maxillofacial silicone elastomer, part 2: mechanical properties after artificial aging.

    PubMed

    Nguyen, Caroline Tram; Chambers, Mark S; Powers, John M; Kiat-Amnuay, Sudarat

    2013-06-01

    There are reports of dissatisfaction with color instability and reduced lifetime of extraoral maxillofacial prostheses. Previous studies showed that UV mineral-based light-protecting agent (LP) improved color stability of MDX4-4210/Type A silicone elastomer. However, effects of this agent and opacifiers on mechanical properties of the elastomer are unknown. The purpose of this study was to evaluate the effect of 2 commonly used opacifiers and LP, a new opacifier, when combined with pigments on the mechanical properties of MDX4-4210/Type A silicone elastomer before and after artificial aging. Two commonly used opacifiers, titanium white dry pigment (TW) and silicone intrinsic white (SW) and LP were each combined with MDX4-4210/type A. Artists' oil pigment was then combined with the LP and TW groups, and silicone intrinsic pigments were combined with the SW group with 5 colors (no pigment=control, red, yellow, blue, or a combination of the 3 pigments). Ten dumbbell-shaped and 10 trouser-shaped specimens of each opacifier + pigment mixture, plus a control group with no opacifier and no pigment, were made for a total of 320 specimens. Half of the specimens (n=5) were aged in a chamber at 450 kJ/m(2). Specimens were tested for hardness (ASTM D2240), tensile strength (ASTM D412), tear strength (ASTM D624), and percentage elongation in a universal testing machine. A 3-way ANOVA and the Fisher PLSD test were performed (α=.05) for each mechanical property. After accelerated aging, values of Shore A hardness were the lowest for LP with all 5 pigments and the control, followed by SW and TW (P<.001). After accelerated aging, tear strength, tensile strength, and elongation decreased significantly (P<.001) for LP, whereas changes for SW and TW varied depending on the pigment. The mechanical properties of specimens with the light-protecting opacifier were adversely affected after being subjected to artificial aging. SW and TW preserved the mechanical properties of silicone in this study. Copyright © 2013 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

  15. 46 CFR 34.01-15 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., http://www.astm.org. (1) ASTM F 1121-87 (Reapproved 1993), Standard Specification for International...-9101, telephone 800-344-3555, http://www.nfpa.org. (1) NFPA 13-1996, Standard for the Installation of...

  16. Standards and guidelines for biopolymers in tissue-engineered medical products: ASTM alginate and chitosan standard guides. American Society for Testing and Materials.

    PubMed

    Dornish, M; Kaplan, D; Skaugrud, O

    2001-11-01

    The American Society for Testing and Materials (ASTM) is making a concerted effort to establish standards and guidelines for the entire field of tissue-engineered medical products (TEMPS). Safety, consistency, and functionality of biomaterials used as matrices, scaffolds, and immobilizing agents in TEMPS are a concern. Therefore, the ASTM has established a number of task groups to produce standards and guidelines for such biomaterials. Alginate is a naturally occurring biomaterial used for immobilizing living cells to form an artificial organ, such as encapsulated pancreatic islets. In order to aid in successful clinical applications and to help expedite regulatory approval, the alginate used must be fully documented. The ASTM alginate guide gives information on selection of testing methodologies and safety criteria. Critical parameters such as monomer content, molecular weight, and viscosity, in addition to more general parameters, such as dry matter content, heavy metal content, bioburden, and endotoxin content are described in the ASTM document. In a like manner, the characterization parameters for chitosan, a bioadhesive polycationic polysaccharide, are described in a separate guide. For chitosan, the degree of deacetylation is of critical importance. Control of protein content and, hence, potential for hypersensitivity, endotoxin content, and total bioburden are important in chitosan preparations for TEMPS. Together these two guides represent part of the effort on behalf of the ASTM and other interested parties to ensure quality and standardization in TEMPS.

  17. Retail colour stability of lamb meat is influenced by breed type, muscle, packaging and iron concentration.

    PubMed

    Warner, R D; Kearney, G; Hopkins, D L; Jacob, R H

    2017-07-01

    The longissmus lumborum (LL) and semimembranosus (SM) muscles from 391 lamb carcasses, derived from various breed types, were used to investigate the effect of animal/muscle factors, packaging type [over-wrap (OW) or high oxygen modified atmosphere packaging (MAP O2 )] and duration of display on redness of meat during simulated retail display. Using statistical models the time required (in days) for redness to reach a threshold value of 3.5 (below this is unacceptable) was predicted. High levels of iron in the SM, but not LL, reduced the time for redness to reach 3.5 by 2-2.6days in MAP O2 and 0.5-0.8days in OW. The greater the proportion of Merino breed type, the shorter was the time for redness to reach the value of 3.5, an effect consistent across muscles and packaging types. In summary, breed type, packaging format, muscle and muscle iron levels had a significant impact on colour stability of sheep meat in oxygen-available packaging systems. Copyright © 2017. Published by Elsevier Ltd.

  18. Santa Ana River Design Memorandum Number 1. Phase 2. GDM on the Santa Ana River Mainstem, Including Santiago Creek. Volume 6. Santiago Creek

    DTIC Science & Technology

    1988-08-01

    requirements of ASTM C 150. 8-10 The Kaiser Cement Company plant in the Lucerne Valley , located approximately 100 miles from the project, produces Type II...land classification of the greater Los Angeles area; Part III Classification of sand and gravel resource areas, Orange County-Temescal Valley Production...Memorandum No. i 4. TITLE (eod Subtitle) 5. TYPE OF REPORT a P ERIOD COVERED Phase II GDM on the Santa Ana River MainstemIncluding Santiago Creek Final

  19. An Elementary Overview of the Selection of Materials for Service in Oxygen-Enriched Environments

    NASA Technical Reports Server (NTRS)

    Davis, Samuel Eddie

    2012-01-01

    The process for selecting materials for use in oxygen or oxygen-enriched environments is one that continues to be investigated by many industries due to the importance to those industries of oxygen systems. There are several excellent resources available to assist oxygen systems design engineers and end-users, with the most comprehensive being ASTM MNL-36, Safe Use of Oxygen and Oxygen Systems: Handbook for Design, Operation and Maintenance, 2nd Edition. ASTM also makes available several standards for oxygen systems. However, the ASTM publications are extremely detailed, and typically designed for professionals who already possess a working knowledge of oxygen systems. No notable resource exists, whether an ASTM or other organizational publication, which can be used to educate engineers or technicians who have no prior knowledge of the nuances of oxygen system design and safety. This paper will fill the void for information needed by organizations that design or operate oxygen systems. The information in this paper is not new information, but is a concise and easily understood summary of selecting materials for oxygen systems. This paper will serve well as an employee s first introduction to oxygen system materials selection, and probably the employee s first introduction to ASTM.

  20. 77 FR 67678 - Content Specifications and Shielding Evaluations for Type B Transportation Packages

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-13

    ...The U.S. Nuclear Regulatory Commission (NRC or the Commission) is issuing for public comment Draft Regulatory Issue Summary (RIS) 2012-XX, ``Content Specifications and Shielding Evaluations for Type B Transportation Packages.'' This RIS clarifies the NRC's use of staff guidance in NUREG-1609, ``Standard Review Plan for Transport Packages for Radioactive Material,'' for the review of content specifications and shielding evaluations included in the Certificates of Compliance (CoC) and safety analysis reports (SARs) for Type B transportation packages.

  1. 40 CFR 91.6 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Appendix A to Subpart D. ASTM D2699-92: Standard Test Method for Knock Characteristics of Motor Fuels by the Research Method Appendix A to Subpart D. ASTM D2700-92: Standard Test Method for Knock...

  2. 40 CFR 91.6 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Appendix A to Subpart D. ASTM D2699-92: Standard Test Method for Knock Characteristics of Motor Fuels by the Research Method Appendix A to Subpart D. ASTM D2700-92: Standard Test Method for Knock...

  3. Child-resistant and tamper-resistant packaging: A systematic review to inform tobacco packaging regulation.

    PubMed

    Jo, Catherine L; Ambs, Anita; Dresler, Carolyn M; Backinger, Cathy L

    2017-02-01

    We aimed to investigate the effects of special packaging (child-resistant, adult-friendly) and tamper-resistant packaging on health and behavioral outcomes in order to identify research gaps and implications for packaging standards for tobacco products. We searched seven databases for keywords related to special and tamper-resistant packaging, consulted experts, and reviewed citations of potentially relevant studies. 733 unique papers were identified. Two coders independently screened each title and abstract for eligibility. They then reviewed the full text of the remaining papers for a second round of eligibility screening. Included studies investigated a causal relationship between type of packaging or packaging regulation and behavioral or health outcomes and had a study population composed of consumers. Studies were excluded on the basis of publication type, if they were not peer-reviewed, and if they had low external validity. Two reviewers independently coded each paper for study and methodological characteristics and limitations. Discrepancies were discussed and resolved. The review included eight studies: four assessing people's ability to access the contents of different packaging types and four evaluating the impact of packaging requirements on health-related outcomes. Child-resistant packaging was generally more difficult to open than non-child-resistant packaging. Child-resistant packaging requirements have been associated with reductions in child mortality. Child-resistant packaging holds the expectation to reduce tobacco product poisonings among children under six. Published by Elsevier Inc.

  4. Child-resistant and tamper-resistant packaging: A systematic review to inform tobacco packaging regulation

    PubMed Central

    Jo, Catherine L.; Ambs, Anita; Dresler, Carolyn M.; Backinger, Cathy L.

    2017-01-01

    Objective We aimed to investigate the effects of special packaging (child-resistant, adult-friendly) and tamper-resistant packaging on health and behavioral outcomes in order to identify research gaps and implications for packaging standards for tobacco products. Methods We searched seven databases for keywords related to special and tamper-resistant packaging, consulted experts, and reviewed citations of potentially relevant studies. 733 unique papers were identified. Two coders independently screened each title and abstract for eligibility. They then reviewed the full text of the remaining papers for a second round of eligibility screening. Included studies investigated a causal relationship between type of packaging or packaging regulation and behavioral or health outcomes and had a study population composed of consumers. Studies were excluded on the basis of publication type, if they were not peer-reviewed, and if they had low external validity. Two reviewers independently coded each paper for study and methodological characteristics and limitations. Discrepancies were discussed and resolved. Results The review included eight studies: four assessing people’s ability to access the contents of different packaging types and four evaluating the impact of packaging requirements on health-related outcomes. Child-resistant packaging was generally more difficult to open than non-child-resistant packaging. Child-resistant packaging requirements have been associated with reductions in child mortality. Conclusions Child-resistant packaging holds the expectation to reduce tobacco product poisonings among children under six. PMID:27939602

  5. Soils Project Risk-Based Corrective Action Evaluation Process with ROTC 1 and ROTC 2, Revision 0

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Matthews, Patrick; Sloop, Christina

    2012-04-01

    This document formally defines and clarifies the NDEP-approved process the NNSA/NSO Soils Activity uses to fulfill the requirements of the FFACO and state regulations. This process is used to establish FALs in accordance with the risk-based corrective action (RBCA) process stipulated in Chapter 445 of the Nevada Administrative Code (NAC) as described in the ASTM International (ASTM) Method E1739-95 (NAC, 2008; ASTM, 1995). It is designed to provide a set of consistent standards for chemical and radiological corrective actions.

  6. Compliance Testing of Grissom Air Force Base Central Heating Plant Coal- Fired Boilers 3, 4, and 5, Grissom Air Force Base, Indiana

    DTIC Science & Technology

    1992-06-01

    coal as classified ac- Department of Environmental Manage- be or, a wet basis and the following conver- cording to ASTM D388-88, "Standard ment...fifteen (15) minutes at the same Sec. 5. (a) Owners or operators of af- erifte p)iute at te me coal as classified according to ASTM fected facilities shall...representative of normal operations or conditions; under other capacities or conditions Testing and Materials ( ASTM ) proce- (B) additional tests to allow

  7. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

  8. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

  9. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

  10. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

  11. 49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... for liquids and gases. 173.466 Section 173.466 Transportation Other Regulations Relating to...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

  12. Arsenic transformation predisposes human skin keratinocytes to UV-induced DNA damage yet enhances their survival apparently by diminishing oxidant response

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sun Yang; Kojima, Chikara; Chignell, Colin

    2011-09-15

    Inorganic arsenic and UV, both human skin carcinogens, may act together as skin co-carcinogens. We find human skin keratinocytes (HaCaT cells) are malignantly transformed by low-level arsenite (100 nM, 30 weeks; termed As-TM cells) and with transformation concurrently undergo full adaptation to arsenic toxicity involving reduced apoptosis and oxidative stress response to high arsenite concentrations. Oxidative DNA damage (ODD) is a possible mechanism in arsenic carcinogenesis and a hallmark of UV-induced skin cancer. In the current work, inorganic arsenite exposure (100 nM) did not induce ODD during the 30 weeks required for malignant transformation. Although acute UV-treatment (UVA, 25 J/cm{supmore » 2}) increased ODD in passage-matched control cells, once transformed by arsenic to As-TM cells, acute UV actually further increased ODD (> 50%). Despite enhanced ODD, As-TM cells were resistant to UV-induced apoptosis. The response of apoptotic factors and oxidative stress genes was strongly mitigated in As-TM cells after UV exposure including increased Bcl2/Bax ratio and reduced Caspase-3, Nrf2, and Keap1 expression. Several Nrf2-related genes (HO-1, GCLs, SOD) showed diminished responses in As-TM cells after UV exposure consistent with reduced oxidant stress response. UV-exposed As-TM cells showed increased expression of cyclin D1 (proliferation gene) and decreased p16 (tumor suppressor). UV exposure enhanced the malignant phenotype of As-TM cells. Thus, the co-carcinogenicity between UV and arsenic in skin cancer might involve adaptation to chronic arsenic exposure generally mitigating the oxidative stress response, allowing apoptotic by-pass after UV and enhanced cell survival even in the face of increased UV-induced oxidative stress and increased ODD. - Highlights: > Arsenic transformation adapted to UV-induced apoptosis. > Arsenic transformation diminished oxidant response. > Arsenic transformation enhanced UV-induced DNA damage.« less

  13. Creep and microstructural processes in a low-alloy 2.25%Cr1.6%W steel (ASTM Grade 23)

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kucharova, K.; Sklenicka, V., E-mail: sklen@ipm.cz; CEITEC — IPM, Institute of Physics of Materials, Academy of Sciences of the Czech Republic, CZ-616 62 Brno

    2015-11-15

    A low-alloy 2.25%Cr1%Mo steel (ASTM Grade 22) has been greatly improved by the substitution of almost all of the 1%Mo by 1.6%W. The improved material has been standardized as P/T23 steel (Fe–2.25Cr–1.6W–0.25V–0.05Nb–0.07C). The present investigation was conducted on T23 steel in an effort to obtain a more complete description and understanding of the role of the microstructural evolution and deformation processes in high-temperature creep. Constant load tensile creep tests were carried out in an argon atmosphere in the temperature range 500–650 °C at stresses ranging from 50 to 400 MPa. It was found that the diffusion in the matrix latticemore » is the creep-rate controlling process. The results of an extensive transmission electron microscopy (TEM) analysis programme to investigate microstructure evolution as a function of temperature are described and compared with the thermodynamic calculations using the software package Thermo-Calc. The significant creep-strength drop of T23 steel after long-term creep exposures can be explained by the decrease in dislocation hardening, precipitation hardening and solid solution hardening due to the instability of the microstructure at high temperature. - Highlights: • The constant load creep tests of T23 steel were carried out at 500–650 °C. • The stress exponents of the creep rate correspond to power law (dislocation) creep. • Diffusion in the matrix lattice is the creep-rate controlling process. • The microstructure instability is the main creep degradation process in T23 steel.« less

  14. Packaging Your Training Materials

    ERIC Educational Resources Information Center

    Espeland, Pamela

    1977-01-01

    The types of packaging and packaging materials to use for training materials should be determined during the planning of the training programs, according to the packaging market. Five steps to follow in shopping for packaging are presented, along with a list of packaging manufacturers. (MF)

  15. 33 CFR 127.003 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Testing and Materials (ASTM) 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM F 1121-87 (1993... NFPA 51B, Fire Prevention in Use of Cutting and Welding Processes, 1994 127.405; 127.1405 NFPA 59A...

  16. 49 CFR 179.220-25 - Stamping.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ...: Material ASTM A240-316L. Shell thickness Shell 0.167 in. Head thickness Head 0.150 in. Tank builders initials ABC. Date of original test 00-0000. Outer shell: Material ASTM A285-C. Tank builders initials WYZ...

  17. 40 CFR 60.41b - Definitions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Society of Testing and Materials in ASTM D3699 (incorporated by reference, see § 60.17), biodiesel as... § 60.17), or biodiesel blends as defined by the American Society of Testing and Materials in ASTM D7467...

  18. 40 CFR 60.41b - Definitions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Society of Testing and Materials in ASTM D3699 (incorporated by reference, see § 60.17), biodiesel as... § 60.17), or biodiesel blends as defined by the American Society of Testing and Materials in ASTM D7467...

  19. 40 CFR 60.41b - Definitions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Society of Testing and Materials in ASTM D3699 (incorporated by reference, see § 60.17), biodiesel as... § 60.17), or biodiesel blends as defined by the American Society of Testing and Materials in ASTM D7467...

  20. ASTM METHODS

    EPA Science Inventory

    ASTM is a not-for-profit organization that provides a forum for producers, users, ultimate consumers, and those having a general interest (representatives of government and academia) to meet on common ground and write standards for materials, products, systems, and services. From...

  1. 40 CFR 72.13 - Incorporation by reference.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...-2959, phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D388-92, Standard... Library (MD-35), U.S. EPA, Research Triangle Park, North Carolina or at the National Archives and Records...

  2. 40 CFR 72.13 - Incorporation by reference.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...-2959, phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D388-92, Standard... Library (MD-35), U.S. EPA, Research Triangle Park, North Carolina or at the National Archives and Records...

  3. 40 CFR 72.13 - Incorporation by reference.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...-2959, phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D388-92, Standard... Library (MD-35), U.S. EPA, Research Triangle Park, North Carolina or at the National Archives and Records...

  4. 40 CFR 72.13 - Incorporation by reference.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...-2959, phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D388-92, Standard... Library (MD-35), U.S. EPA, Research Triangle Park, North Carolina or at the National Archives and Records...

  5. 46 CFR 95.01-2 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., PA 19428-2959, telephone 610-832-9585, http://www.astm.org. (1) ASTM F 1121-87 (1993), Standard... Park, Quincy, MA 02269-9101, telephone 800-344-3555, http://www.nfpa.org. (1) NFPA 13-1996, Standard...

  6. 46 CFR 193.01-3 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Conshohocken, PA 19428-2959, telephone 610-832-9585, http://www.astm.org. (1) ASTM F 1121-87 (1993), Standard... Park, Quincy, MA 02269-9101, telephone 800-344-3555, http://www.nfpa.org. (1) NFPA 13-1996, Standard...

  7. Microstructural Evaluation of Forging Parameters for Superalloy Disks

    NASA Technical Reports Server (NTRS)

    Falsey, John R.

    2004-01-01

    Forgings of nickel base superalloy were formed under several different strain rates and forging temperatures. Samples were taken from each forging condition to find the ASTM grain size, and the as large as grain (ALA). The specimens were mounted in bakelite, polished, etched and then optical microscopy was used to determine grain size. The specimens ASTM grain sizes from each forging condition were plotted against strain rate, forging temperature, and presoak time. Grain sizes increased with increasing forging temperature. Grain sizes also increased with decreasing strain rates and increasing forging presoak time. The ALA had been determined from each forging condition using the ASTM standard method. Each ALA was compared with the ASTM grain size of each forging condition to determine if the grain sizes were uniform or not. The forging condition of a strain rate of .03/sec and supersolvus heat treatment produced non uniform grains indicated by critical grain growth. Other anomalies are noted as well.

  8. Effect of nanoclay on the properties of low density polyethylene/linear low density polyethylene/thermoplastic starch blend films.

    PubMed

    Sabetzadeh, Maryam; Bagheri, Rouhollah; Masoomi, Mahmood

    2016-05-05

    The aim of this work is to study effect of nanoclay (Cloisite(®)15A) on morphology and properties of low-density polyethylene/linear low-density polyethylene/thermoplastic starch (LDPE/LLDPE/TPS) blend films. LDPE/LLDPE blend (70/30wt/wt) containing 15wt.% TPS in the presence of PE-grafted maleic anhydride (PE-g-MA, 3wt.%) with 1, 3 and 5phr of nanoclay are compounded in a twin-screw extruder and then film blown using a blowing machine. Nanocomposites with intercalated structures are obtained, based on the X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies. However, some exfoliated single platelets in the samples are also observable. Scanning electron microscopic (SEM) images confirm the ability of both exfoliated nanoclay and PE-g-MA to reduce the size of TPS domains and deform their particles within the PE matrices. As the nanoclay content increases from 1 to 5phr, the tensile strength, tear resistance and impact strength of the films increase, whereas a slight decrease in the elongation at break is observed. The film samples with 5phr nanoclay possess the required packaging properties, as specified by ASTM D4635. These films provide desired optical transparency and surface roughness which are more attractive for packaging applications. Copyright © 2016. Published by Elsevier Ltd.

  9. Implementing Monitored Natural Attenuation and Expediting Closure at Fuel-Release Sites

    DTIC Science & Technology

    2004-08-01

    Center for Environmental Excellence AFCEE/ERS Air Force Center for Environmental Excellence/Science and Engineering Division AFRPA Air Force Real...auger, air - or mud- rotary , cable-tool) was and is dependent on the target drilling depths and the types of subsurface materials expected to be...95(2000) ASTM. 1995c. Guide for the use of direct air - rotary drilling for geoenvironmental exploration and installation of subsurface water quality

  10. ITS-90 Thermocouple Database

    National Institute of Standards and Technology Data Gateway

    SRD 60 NIST ITS-90 Thermocouple Database (Web, free access)   Web version of Standard Reference Database 60 and NIST Monograph 175. The database gives temperature -- electromotive force (emf) reference functions and tables for the letter-designated thermocouple types B, E, J, K, N, R, S and T. These reference functions have been adopted as standards by the American Society for Testing and Materials (ASTM) and the International Electrotechnical Commission (IEC).

  11. Microstructural characterization of as-cast biocompatible Co-Cr-Mo alloys

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Giacchi, J.V., E-mail: jgiacchi@exa.unicen.edu.ar; Instituto de Fisica de Materiales Tandil; Morando, C.N.

    2011-01-15

    The microstructure of a cobalt-base alloy (Co-Cr-Mo) obtained by the investment casting process was studied. This alloy complies with the ASTM F75 standard and is widely used in the manufacturing of orthopedic implants because of its high strength, good corrosion resistance and excellent biocompatibility properties. This work focuses on the resulting microstructures arising from samples poured under industrial environment conditions, of three different Co-Cr-Mo alloys. For this purpose, we used: 1) an alloy built up from commercial purity constituents, 2) a remelted alloy and 3) a certified alloy for comparison. The characterization of the samples was achieved by using opticalmore » microscopy (OM) with a colorant etchant to identify the present phases and scanning electron microscopy (SE-SEM) and energy dispersion spectrometry (EDS) techniques for a better identification. In general the as-cast microstructure is a Co-fcc dendritic matrix with the presence of a secondary phase, such as the M{sub 23}C{sub 6} carbides precipitated at grain boundaries and interdendritic zones. These precipitates are the main strengthening mechanism in this type of alloys. Other minority phases were also reported and their presence could be linked to the cooling rate and the manufacturing process variables and environment. - Research Highlights: {yields}The solidification microstructure of an ASTM-F75 type alloy were studied. {yields}The alloys were poured under an industrial environment. {yields}Carbides and sigma phase identified by color metallography and scanning microscopy (SEM and EDS). {yields}Two carbide morphologies were detected 'blocky type' and 'pearlite type'. {yields}Minority phases were also detected.« less

  12. Interlaboratory evaluation of a standardized inductively coupled plasma mass spectrometry method for the determination of trace beryllium in air filter samples.

    PubMed

    Ashley, Kevin; Brisson, Michael J; Howe, Alan M; Bartley, David L

    2009-12-01

    A collaborative interlaboratory evaluation of a newly standardized inductively coupled plasma mass spectrometry (ICP-MS) method for determining trace beryllium in workplace air samples was carried out toward fulfillment of method validation requirements for ASTM International voluntary consensus standard test methods. The interlaboratory study (ILS) was performed in accordance with an applicable ASTM International standard practice, ASTM E691, which describes statistical procedures for investigating interlaboratory precision. Uncertainty was also estimated in accordance with ASTM D7440, which applies the International Organization for Standardization Guide to the Expression of Uncertainty in Measurement to air quality measurements. Performance evaluation materials (PEMs) used consisted of 37 mm diameter mixed cellulose ester filters that were spiked with beryllium at levels of 0.025 (low loading), 0.5 (medium loading), and 10 (high loading) microg Be/filter; these spiked filters were prepared by a contract laboratory. Participating laboratories were recruited from a pool of over 50 invitees; ultimately, 20 laboratories from Europe, North America, and Asia submitted ILS results. Triplicates of each PEM (blanks plus the three different loading levels) were conveyed to each volunteer laboratory, along with a copy of the draft standard test method that each participant was asked to follow; spiking levels were unknown to the participants. The laboratories were requested to prepare the PEMs by one of three sample preparation procedures (hotplate or microwave digestion or hotblock extraction) that were described in the draft standard. Participants were then asked to analyze aliquots of the prepared samples by ICP-MS and to report their data in units of mu g Be/filter sample. Interlaboratory precision estimates from participating laboratories, computed in accordance with ASTM E691, were 0.165, 0.108, and 0.151 (relative standard deviation) for the PEMs spiked at 0.025, 0.5, and 10 microg Be/filter, respectively. Overall recoveries were 93.2%, 102%, and 80.6% for the low, medium, and high beryllium loadings, respectively. Expanded uncertainty estimates for interlaboratory analysis of low, medium, and high beryllium loadings, calculated in accordance with ASTM D7440, were 18.8%, 19.8%, and 24.4%, respectively. These figures of merit support promulgation of the analytical procedure as an ASTM International standard test method, ASTM D7439.

  13. White Paper Summary of 2nd ASTM International Workshop on Hydrides in Zirconium Alloy Cladding

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Sindelar, R.; Louthan, M.; PNNL, B.

    2015-05-29

    This white paper recommends that ASTM International develop standards to address the potential impact of hydrides on the long term performance of irradiated zirconium alloys. The need for such standards was apparent during the 2nd ASTM International Workshop on Hydrides in Zirconium Alloy Cladding and Assembly Components, sponsored by ASTM International Committee C26.13 and held on June 10-12, 2014, in Jackson, Wyoming. The potentially adverse impacts of hydrogen and hydrides on the long term performance of irradiated zirconium-alloy cladding on used fuel were shown to depend on multiple factors such as alloy chemistry and processing, irradiation and post irradiation history,more » residual and applied stresses and stress states, and the service environment. These factors determine the hydrogen content and hydride morphology in the alloy, which, in turn, influence the response of the alloy to the thermo-mechanical conditions imposed (and anticipated) during storage, transport and disposal of used nuclear fuel. Workshop presentations and discussions showed that although hydrogen/hydride induced degradation of zirconium alloys may be of concern, the potential for occurrence and the extent of anticipated degradation vary throughout the nuclear industry because of the variations in hydrogen content, hydride morphology, alloy chemistry and irradiation conditions. The tools and techniques used to characterize hydrides and hydride morphologies and their impacts on material performance also vary. Such variations make site-to-site comparisons of test results and observations difficult. There is no consensus that a single material or system characteristic (e.g., reactor type, burnup, hydrogen content, end-of life stress, alloy type, drying temperature, etc.) is an effective predictor of material response during long term storage or of performance after long term storage. Multi-variable correlations made for one alloy may not represent the behavior of another alloy exposed to identical conditions and the material responses to thermo-mechanical exposures will be different depending on the materials and systems used. The discussions at the workshop showed several gaps in the standardization of processes and techniques necessary to assess the long term performance of irradiated zirconium alloy cladding during dry storage and transport. The development of, and adherence to, standards to help bridge these gaps will strengthen the technical basis for long term storage and post-storage operations, provide consistency across the nuclear industry, maximize the value of most observations, and enhance the understanding of behavioral differences among alloys. The need for, and potential benefits of, developing the recommended standards are illustrated in the various sections of this report.« less

  14. 78 FR 26090 - Content Specifications and Shielding Evaluations for Type B Transportation Packages

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-03

    ...The U.S. Nuclear Regulatory Commission (NRC) is issuing Regulatory Issue Summary (RIS) 2013-04, ``Content Specifications and Shielding Evaluations for Type B Transportation Packages.'' This RIS clarifies the NRC's use of staff guidance in NUREG-1609, ``Standard Review Plan for Transport Packages for Radioactive Material,'' for the review of content specifications and shielding evaluations included in the Certificates of Compliance (CoC) and safety analysis reports (SARs) for Type B transportation packages. The RIS does not impose any additional regulatory requirements on NRC licensees.

  15. Repetitive member factors for the allowable properties of wood products

    Treesearch

    Steve Verrill; David Kretschmann

    2010-01-01

    We identify confusion in the literature about the definition and calculation of repetitive member factors. This confusion casts some doubt on the validity of the 1.15 repetitive member factor permitted in ASTM D 245 and ASTM D 1990.

  16. 46 CFR 35.25-10 - Requirements for fuel oil-T/ALL.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... tankships shall have a flashpoint of not less than 140°F. (Pensky-Martens Closed Cup Method, ASTM D 93... vendor, the name of the oil producer, and the flashpoint (Pensky-Martens Closed Cup Method, ASTM D 93...

  17. 46 CFR 35.25-10 - Requirements for fuel oil-T/ALL.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... tankships shall have a flashpoint of not less than 140°F. (Pensky-Martens Closed Cup Method, ASTM D 93... vendor, the name of the oil producer, and the flashpoint (Pensky-Martens Closed Cup Method, ASTM D 93...

  18. 49 CFR 173.415 - Authorized Type A packages.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... tests and an engineering evaluation or comparative data showing that the construction methods, packaging design, and materials of construction comply with that specification. After January 1, 2017 each offeror... meets the pertinent design and performance requirements for a DOT 7A Type A specification package. (2...

  19. Use of the Digital Surface Roughness Meter in Virginia.

    DOT National Transportation Integrated Search

    2006-01-01

    Pavement surface texture is measured in a variety of ways in Virginia. Two methods commonly used are ASTM E 965, Standard Test Method for Measuring Pavement Macrotexture Depth Using a Volumetric Technique, known as the "sand patch" test, and ASTM E 2...

  20. 76 FR 67673 - Welded ASTM A-312 Stainless Steel Pipe From South Korea and Taiwan: Final Results of Expedited...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-02

    ... meets the standards and specifications set forth by the American Society for Testing and Materials (ASTM... produced by forming stainless steel flat-rolled products into a tubular configuration and welding along the...

  1. Performance of gravel aggregates in superpave mixes with 100/95 angularity.

    DOT National Transportation Integrated Search

    2010-04-01

    The research conducted in this study evaluated the asphalt mixture performance of various gravel and : crushed stone sources consisting of different levels of crushed face counts, as determined by ASTM D5821. : Along with ASTM D5821, two additional a...

  2. 30 CFR 75.301 - Definitions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...-warning fire detection systems using newer technology that provides equal or greater protection, as... be purchased from the American Society for Testing Materials (ASTM), 1916 Race Street, Philadelphia..., copies of the document can be purchased from the American Society for Testing Materials (ASTM), 100 Barr...

  3. 49 CFR 173.411 - Industrial packages.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...) Each Type IP-1 package must meet the general design requirements prescribed in § 173.410. (2) Each Type IP-2 package must meet the general design requirements prescribed in § 173.410 and when subjected to...), “Requirements for the Design, Construction, Inspection and Testing of Portable Tanks and Multiple-Element Gas...

  4. 49 CFR 178.970 - Bottom lift test.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Large Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... permissible gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types...

  5. 49 CFR 178.970 - Bottom lift test.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types must be...

  6. 49 CFR 178.970 - Bottom lift test.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types must be...

  7. 49 CFR 178.970 - Bottom lift test.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types must be...

  8. 49 CFR 178.970 - Bottom lift test.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Packagings design types designed to be lifted from the base, there may be no permanent deformation which renders the Large Packaging unsafe for transport and there must be no loss of contents. ... gross mass, the load being evenly distributed. (c) Test method. All Large Packaging design types must be...

  9. Arsenic-induced malignant transformation of human keratinocytes: Involvement of Nrf2

    PubMed Central

    Pi, Jingbo; Diwan, Bhalchandra A.; Sun, Yang; Liu, Jie; Qu, Wei; He, Yuying; Styblo, Miroslav; Waalkes, Michael P.

    2009-01-01

    Arsenic is a well-known human skin carcinogen but the underlying mechanisms of carcinogenesis are unclear. Transcription factor Nrf2-mediated antioxidant response represents a critical cellular defense mechanism, and emerging data suggest that constitutive activation of Nrf2 contributes to malignant phenotype. In the present study when an immortalized, non-tumorigenic human keratinocyte cell line (HaCaT) was continuously exposed to environmentally relevant level of inorganic arsenite (100 nM) for 28 weeks, malignant transformation occurred as evidenced by the formation of highly aggressive squamous cell carcinoma after inoculation into nude mice. To investigate the mechanisms involved, a broad array of biomarkers for transformation were assessed in these arsenic-transformed cells (termed As-TM). In addition to increased secretion of matrix metalloproteinase-9 (MMP-9), a set of markers for squamous differentiation and skin keratinization, including keratin-1, keratin-10, involucrin, and loricrin, were significantly elevated in As-TM cells. Furthermore, As-TM cells showed increased intracellular glutathione, elevated expression of Nrf2 and its target genes, as well as generalized apoptotic resistance. In contrast to increased basal Nrf2 activity in As-TM cells, a diminished Nrf2-mediated antioxidant response induced by acute exposure to high dose of arsenite or tert-butyl hydroxyquinone occurred. The findings that multiple biomarkers for malignant transformation observed in As-TM cells, including MMP-9 and cytokeratins, are potentially regulated by Nrf2 suggest constitutive Nrf2 activation may be involved in arsenic carcinogenesis of skin. The weakened Nrf2 activation in response to oxidative stressors observed in As-TM cells, coupled with acquired apoptotic resistance, would potentially have increased the likelihood of transmittable oxidative DNA damage and fixation of mutational/DNA damage events. PMID:18572023

  10. Methods for Evaluating Flammability Characteristics of Shipboard Materials

    DTIC Science & Technology

    1994-02-28

    E 23 • smoke optical properties; and • (toxic) gas production rates. In general, the prediction of these full-scale burning characteristics requires ...Method. The ASTM Room/Corner Test Method can be used to calculate the heat release rate of a material based upon oxygen depletion calorimetry. As can be...Clearly, more validation is required for the theoretical calculations . All are consistent in the use of calorimeter and UFT-type property data, all show

  11. Crush Testing at Oak Ridge National Laboratory

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Feldman, Matthew R

    2011-01-01

    The dynamic crush test is required in the certification testing of some small Type B transportation packages. International Atomic Energy Agency regulations state that the test article must be 'subjected to a dynamic crush test by positioning the specimen on the target so as to suffer maximum damage.' Oak Ridge National Laboratory (ORNL) Transportation Technologies Group performs testing of Type B transportation packages, including the crush test, at the National Transportation Research Center in Knoxville, Tennessee (United States). This paper documents ORNL's experiences performing crush tests on several different Type B packages. ORNL has crush tested five different drum-type packagemore » designs, continuing its 60 year history of RAM package testing. A total of 26 crush tests have been performed in a wide variety of package orientations and crush plate CG alignments. In all cases, the deformation of the outer drum created by the crush test was significantly greater than the deformation damage caused by the 9 m drop test. The crush test is a highly effective means for testing structural soundness of smaller nondense Type B shipping package designs. Further regulatory guidance could alleviate the need to perform the crush test in a wide range of orientations and crush plate CG alignments.« less

  12. Safety analysis report -- Packages LP-50 tritium package (Packaging of fissile and other radioactive materials)

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Gates, A.A.; McCarthy, P.G.; Edl, J.W.

    1975-05-01

    Elemental tritium is shipped at low pressure in a stainless steel container (LP-50) surrounded by an aluminum vessel and Celotex insulation at least 4 in. thick in a steel drum. Each package contains a large quantity (greater than a Type A quantity) of nonfissile material, as defined in AECM 0529. This report provides the details of the safety analysis performed for this type container.

  13. Laboratory comparison of several tests for evaluating the transport properties of concrete.

    DOT National Transportation Integrated Search

    2006-01-01

    The transport properties of concrete are a primary element in determining the durability of concrete. In this study, several new test methods that directly measure aspects of fluid and ionic transport in concrete were examined. ASTM C 1543 and ASTM C...

  14. 24 CFR 3285.402 - Ground anchor installations.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... HOUSING AND URBAN DEVELOPMENT MODEL MANUFACTURED HOME INSTALLATION STANDARDS Anchorage Against Wind § 3285... conforming to ASTM D 3953—97, Standard Specification for Strapping, Flat Steel and Seals (incorporated by... in ASTM D 3953-97, Standard Specification for Strapping, Flat Steel and Seals (incorporated by...

  15. 24 CFR 3285.402 - Ground anchor installations.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... HOUSING AND URBAN DEVELOPMENT MODEL MANUFACTURED HOME INSTALLATION STANDARDS Anchorage Against Wind § 3285... conforming to ASTM D 3953—97, Standard Specification for Strapping, Flat Steel and Seals (incorporated by... in ASTM D 3953-97, Standard Specification for Strapping, Flat Steel and Seals (incorporated by...

  16. HACCP: Integrating Science and Management through ASTM Standards

    EPA Science Inventory

    From a technical perspective, hazard analysis-critical control point (HACCP) evaluation may be considered a risk management tool suited to a wide range of applications. As one outcome of a symposium convened by American Society for Testing and Materials (ASTM) in August, 2005, th...

  17. 49 CFR 179.300-7 - Materials.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... ASTM A 515/A 515M Gr. 70 70,000 20 ASTM A 516/A 516M Gr. 70 70,000 20 1 Maximum stresses to be used in...) [Reserved] (c) All plates must have their heat number and the name or brand of the manufacturer legibly...

  18. 49 CFR 179.300-7 - Materials.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... ASTM A 515/A 515M Gr. 70 70,000 20 ASTM A 516/A 516M Gr. 70 70,000 20 1 Maximum stresses to be used in...) [Reserved] (c) All plates must have their heat number and the name or brand of the manufacturer legibly...

  19. Experimental Investigation of Mechanical Properties of Welded Corten Steel A588 Grade Plate Using ER70S - 6 Filler Material for Construction Application

    NASA Astrophysics Data System (ADS)

    Deepak, J. R.; Bupesh Raja, V. K.; Janardhan Guptha, Mittapalli; Durga Prasad, Palaparthi Hari; Sriram, V.

    2017-05-01

    ASTM A588 Grade A steel plate is a high strength, low alloy structural steel with 0.19 % of carbon content. When exposed to the atmosphere, A588 Grade A is suitable for construction in the bare (paint - free) condition. The main problems are lack of fusion, lack of penetration and corrosion on heat affected zone. In this research work Corten ASTM A588 Grade steel of 3mm thickness is electroplated with copper and then both raw and copper electroplated are welded by GMAW welding process with ER70S-6 as a filler material. The welded ASTM A588 is cut according to ASTM size for further testing of mechanical properties. Considering its welding strength after the process of electroplating, this research clearly states the metal can be utilized for better results in any given field. Here both the tensile and hardness are higher in copper electroplated welded when compare to raw welded.

  20. Summary: Update to ASTM guide E 1523 to charge control and charge referencing techniques in x-ray photoelectron spectroscopy

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Baer, D.R.

    2005-05-01

    An updated version of the American Society for Testing and Materials (ASTM) guide E 1523 to the methods to charge control and charge referencing techniques in x-ray photoelectron spectroscopy has been released by ASTM [Annual Book of ASTM Standards Surface Analysis (American Society for Testing and Materials, West Conshohocken, PA, 2004), Vol. 03.06]. The guide is meant to acquaint x-ray photoelectron spectroscopy (XPS) users with the various charge control and charge referencing techniques that are and have been used in the acquisition and interpretation of XPS data from surfaces of insulating specimens. The current guide has been expanded to includemore » new references as well as recommendations for reporting information on charge control and charge referencing. The previous version of the document had been published in 1997 [D. R. Baer and K. D. Bomben, J. Vac. Sci. Technol. A 16, 754 (1998)].« less

  1. Geometric investigation of a gaming active device

    NASA Astrophysics Data System (ADS)

    Menna, Fabio; Remondino, Fabio; Battisti, Roberto; Nocerino, Erica

    2011-07-01

    3D imaging systems are widely available and used for surveying, modeling and entertainment applications, but clear statements regarding their characteristics, performances and limitations are still missing. The VDI/VDE and the ASTME57 committees are trying to set some standards but the commercial market is not reacting properly. Since many new users are approaching these 3D recording methodologies, clear statements and information clarifying if a package or system satisfies certain requirements before investing are fundamental for those users who are not really familiar with these technologies. Recently small and portable consumer-grade active sensors came on the market, like TOF rangeimaging cameras or low-cost triangulation-based range sensor. A quite interesting active system was produced by PrimeSense and launched on the market thanks to the Microsoft Xbox project with the name of Kinect. The article reports the geometric investigation of the Kinect active sensors, considering its measurement performances, the accuracy of the retrieved range data and the possibility to use it for 3D modeling application.

  2. Effects of lamination and coating with drying oils on tensile and barrier properties of zein films.

    PubMed

    Rakotonirainy, A M; Padua, G W

    2001-06-01

    Zein films plasticized with oleic acid have been considered potentially useful for biodegradable packaging applications. However, moisture was found to affect their tensile and gas barrier properties. We investigated the effects of two converting processes, fusion lamination and coating with drying oils, on tensile properties and gas permeability of zein films. Zein films were laminated to 4-ply sheets in a Carver press and coated with tung oil, linseed oil, or a mixture of tung and soybean oils. Tensile properties and permeability to water vapor, oxygen, and carbon dioxide were measured according to ASTM methods. Laminated films were clearer, tougher, and more flexible, and had a smoother finish than nontreated sheets. Lamination decreased O(2) and CO(2) permeability by filling in voids and pinholes in the film structure. Coating increased tensile strength and elongation and decreased water vapor permeability. Coatings acted as a composite layer preventing crack propagation and increasing film strength. They also formed a highly hydrophobic surface that prevented film wetting.

  3. Development of Hospital-based Data Sets as a Vehicle for Implementation of a National Electronic Health Record

    PubMed Central

    Keikha, Leila; Farajollah, Seyede Sedigheh Seied; Safdari, Reza; Ghazisaeedi, Marjan; Mohammadzadeh, Niloofar

    2018-01-01

    Background In developing countries such as Iran, international standards offer good sources to survey and use for appropriate planning in the domain of electronic health records (EHRs). Therefore, in this study, HL7 and ASTM standards were considered as the main sources from which to extract EHR data. Objective The objective of this study was to propose a hospital data set for a national EHR consisting of data classes and data elements by adjusting data sets extracted from the standards and paper-based records. Method This comparative study was carried out in 2017 by studying the contents of the paper-based records approved by the health ministry in Iran and the international ASTM and HL7 standards in order to extract a minimum hospital data set for a national EHR. Results As a result of studying the standards and paper-based records, a total of 526 data elements in 174 classes were extracted. An examination of the data indicated that the highest number of extracted data came from the free text elements, both in the paper-based records and in the standards related to the administrative data. The major sources of data extracted from ASTM and HL7 were the E1384 and Hl7V.x standards, respectively. In the paper-based records, data were extracted from 19 forms sporadically. Discussion By declaring the confidentiality of information, the ASTM standards acknowledge the issue of confidentiality of information as one of the main challenges of EHR development, and propose new types of admission, such as teleconference, tele-video, and home visit, which are inevitable with the advent of new technology for providing healthcare and treating diseases. Data related to finance and insurance, which were scattered in different categories by three organizations, emerged as the financial category. Documenting the role and responsibility of the provider by adding the authenticator/signature data element was deemed essential. Conclusion Not only using well-defined and standardized data, but also adapting EHR systems to the local facilities and the existing social and cultural conditions, will facilitate the development of structured data sets. PMID:29618962

  4. Development of Hospital-based Data Sets as a Vehicle for Implementation of a National Electronic Health Record.

    PubMed

    Keikha, Leila; Farajollah, Seyede Sedigheh Seied; Safdari, Reza; Ghazisaeedi, Marjan; Mohammadzadeh, Niloofar

    2018-01-01

    In developing countries such as Iran, international standards offer good sources to survey and use for appropriate planning in the domain of electronic health records (EHRs). Therefore, in this study, HL7 and ASTM standards were considered as the main sources from which to extract EHR data. The objective of this study was to propose a hospital data set for a national EHR consisting of data classes and data elements by adjusting data sets extracted from the standards and paper-based records. This comparative study was carried out in 2017 by studying the contents of the paper-based records approved by the health ministry in Iran and the international ASTM and HL7 standards in order to extract a minimum hospital data set for a national EHR. As a result of studying the standards and paper-based records, a total of 526 data elements in 174 classes were extracted. An examination of the data indicated that the highest number of extracted data came from the free text elements, both in the paper-based records and in the standards related to the administrative data. The major sources of data extracted from ASTM and HL7 were the E1384 and Hl7V.x standards, respectively. In the paper-based records, data were extracted from 19 forms sporadically. By declaring the confidentiality of information, the ASTM standards acknowledge the issue of confidentiality of information as one of the main challenges of EHR development, and propose new types of admission, such as teleconference, tele-video, and home visit, which are inevitable with the advent of new technology for providing healthcare and treating diseases. Data related to finance and insurance, which were scattered in different categories by three organizations, emerged as the financial category. Documenting the role and responsibility of the provider by adding the authenticator/signature data element was deemed essential. Not only using well-defined and standardized data, but also adapting EHR systems to the local facilities and the existing social and cultural conditions, will facilitate the development of structured data sets.

  5. Tensile-Creep Test Specimen Preparation Practices of Surface Support Liners

    NASA Astrophysics Data System (ADS)

    Guner, Dogukan; Ozturk, Hasan

    2017-12-01

    Ground support has always been considered as a challenging issue in all underground operations. Many forms of support systems and supporting techniques are available in the mining/tunnelling industry. In the last two decades, a new polymer based material, Thin Spray-on Liner (TSL), has attained a place in the market as an alternative to the current areal ground support systems. Although TSL provides numerous merits and has different application purposes, the knowledge on mechanical properties and performance of this material is still limited. In laboratory studies, since tensile rupture is the most commonly observed failure mechanism in field applications, researchers have generally studied the tensile testing of TSLs with modification of American Society for Testing and Materials (ASTM) D-638 standards. For tensile creep testing, specimen preparation process also follows the ASTM standards. Two different specimen dimension types (Type I, Type IV) are widely preferred in TSL tensile testing that conform to the related standards. Moreover, molding and die cutting are commonly used specimen preparation techniques. In literature, there is a great variability of test results due to the difference in specimen preparation techniques and practices. In this study, a ductile TSL product was tested in order to investigate the effect of both specimen preparation techniques and specimen dimensions under 7-day curing time. As a result, ultimate tensile strength, tensile yield strength, tensile modulus, and elongation at break values were obtained for 4 different test series. It is concluded that Type IV specimens have higher strength values compared to Type I specimens and moulded specimens have lower results than that of prepared by using die cutter. Moreover, specimens prepared by molding techniques have scattered test results. Type IV specimens prepared by die cutter technique are suggested for preparation of tensile test and Type I specimens prepared by die cutter technique should be preferred for tensile creep tests.

  6. Effectiveness of some recent antimicrobial packaging concepts.

    PubMed

    Vermeiren, L; Devlieghere, F; Debevere, J

    2002-01-01

    A new type of active packaging is the combination of food-packaging materials with antimicrobial substances to control microbial surface contamination of foods. For both migrating and non-migrating antimicrobial materials, intensive contact between the food product and packaging material is required and therefore potential food applications include especially vacuum or skin-packaged products, e.g. vacuum-packaged meat, fish, poultry or cheese. Several antimicrobial compounds have been combined with different types of carriers (plastic and rubber articles, paper-based materials, textile fibrils and food-packaging materials). Until now, however, few antimicrobial concepts have found applications as a food-packaging material. Antimicrobial packaging materials cannot legally be used in the EU at the moment. The potential use would require amendments of several different legal texts involving areas such as food additives, food packaging, hygiene, etc. The main objective of this paper is to provide a state of the art about the different types of antimicrobial concepts, their experimental development and commercialization, and to present a case study summarizing the results of investigations on the feasibility of a low-density polyethylene (LDPE)-film containing triclosan to inhibit microbial growth on food surfaces and consequently prolong shelf-life or improve microbial food safety. In contrast with the strong antimicrobial effect in in-vitro simulated vacuum-packaged conditions against the psychrotrophic food pathogen L. monocytogenes, the 1000 mg kg(-1) containing triclosan film did not effectively reduce spoilage bacteria and growth of L. monocytogenes on refrigerated vacuum-packaged chicken breasts stored at 7 degrees C.

  7. Comparison of combustion characteristics of ASTM A-1, propane, and natural-gas fuels in an annular turbojet combustor

    NASA Technical Reports Server (NTRS)

    Wear, J. D.; Jones, R. E.

    1973-01-01

    The performance of an annular turbojet combustor using natural-gas fuel is compared with that obtained using ASTM A-1 and propane fuels. Propane gas was used to simulate operation with vaporized kerosene fuels. The results obtained at severe operating conditions and altitude relight conditions show that natural gas is inferior to both ASTM A-1 and propane fuels. Combustion efficiencies were significantly lower and combustor pressures for relight were higher with natural-gas fuel than with the other fuels. The inferior performance of natural gas is shown to be caused by the chemical stability of the methane molecule.

  8. 24 CFR 3280.604 - Materials.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    .... Welding and Seamless Wrought Steel Pipe—ANSI/ASME B36.10-1979. Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless—ASTM A53-93. Pipe Threads, General Purpose (Inch... Seamless Copper Pipe, Standard Sizes—ASTM B42-93. Standard Specification for General Requirements for...

  9. 24 CFR 3280.604 - Materials.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    .... Welding and Seamless Wrought Steel Pipe—ANSI/ASME B36.10-1979. Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless—ASTM A53-93. Pipe Threads, General Purpose (Inch... Seamless Copper Pipe, Standard Sizes—ASTM B42-93. Standard Specification for General Requirements for...

  10. 24 CFR 3280.604 - Materials.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    .... Welding and Seamless Wrought Steel Pipe—ANSI/ASME B36.10-1979. Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless—ASTM A53-93. Pipe Threads, General Purpose (Inch... Seamless Copper Pipe, Standard Sizes—ASTM B42-93. Standard Specification for General Requirements for...

  11. Spray Drift Reduction Evaluations of Spray Nozzles Using a Standardized Testing Protocol

    DTIC Science & Technology

    2010-07-01

    Drop Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments,” Annual Book of ASTM Standards, Vol. 14-02, ASTM...Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Non- imaging Light-Scattering Instruments 22. AGDISP Model

  12. Standard practice for use of scrap tires in civil engineering applications. ASTM standard

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    1998-08-01

    This practice is under the jurisdiction of ASTM Committee D-34 on Biotechnology and is the direct responsibility of Subcommittee D34.06 on Recovery and Reuse. The current edition was approved on Jun. 10, 1998. It was published in August 1998.

  13. 7 CFR 1755.860 - RUS specification for filled buried wires.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... sufficient heat barrier to prevent visible evidence of conductor insulation deformation or adhesion between... Insulations and Jackets for Telecommunications Wire and Cable; ASTM D 4566-90, Standard Test Methods for Electrical Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable; ASTM D...

  14. 7 CFR 1755.860 - RUS specification for filled buried wires.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... sufficient heat barrier to prevent visible evidence of conductor insulation deformation or adhesion between... Insulations and Jackets for Telecommunications Wire and Cable; ASTM D 4566-90, Standard Test Methods for Electrical Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable; ASTM D...

  15. 7 CFR 1755.860 - RUS specification for filled buried wires.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... sufficient heat barrier to prevent visible evidence of conductor insulation deformation or adhesion between... Insulations and Jackets for Telecommunications Wire and Cable; ASTM D 4566-90, Standard Test Methods for Electrical Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable; ASTM D...

  16. Evaluation of Surface Infiltration Testing Procedures in Permeable Pavement Systems

    EPA Science Inventory

    The ASTM method (ASTM C1701) for measuring infiltration rate of in-place pervious concrete provides limited guidance on how to select testing locations, so research is needed to evaluate how testing sites should be selected and how results should be interpreted to assess surface ...

  17. Design, installation, and condition assessment of a concrete bridge deck constructed with ASTM A1035 CS no. 4 bars.

    DOT National Transportation Integrated Search

    2017-06-01

    Recently developed corrosion-resistant reinforcing structural design guidelines were used to design, construct, and : assess a reinforced concrete bridge deck with high-strength ASTM A1035 CS steel bars. The bridge replacement is located : along the ...

  18. 27 CFR 21.114 - Kerosene.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

  19. 27 CFR 21.114 - Kerosene.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

  20. 27 CFR 21.114 - Kerosene.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

  1. 27 CFR 21.114 - Kerosene.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

  2. 27 CFR 21.114 - Kerosene.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Kerosene. 21.114 Section 21.114 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Kerosene. (a) Distillation range. (For applicable ASTM method, see 1980 Annual Book of ASTM Standards, Part...

  3. 40 CFR 260.11 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...). (7) ASTM E 168-88, “Standard Practices for General Techniques of Infrared Quantitative Analysis,” IBR...-Visible Quantitative Analysis,” IBR approved for § 264.1063. (9) ASTM E 260-85, “Standard Practice for... materials are available for purchase from the Environmental Protection Agency, Research Triangle Park, NC...

  4. Conceptual waste packaging options for deep borehole disposal

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Su, Jiann -Cherng; Hardin, Ernest L.

    This report presents four concepts for packaging of radioactive waste for disposal in deep boreholes. Two of these are reference-size packages (11 inch outer diameter) and two are smaller (5 inch) for disposal of Cs/Sr capsules. All four have an assumed length of approximately 18.5 feet, which allows the internal length of the waste volume to be 16.4 feet. However, package length and volume can be scaled by changing the length of the middle, tubular section. The materials proposed for use are low-alloy steels, commonly used in the oil-and-gas industry. Threaded connections between packages, and internal threads used to sealmore » the waste cavity, are common oilfield types. Two types of fill ports are proposed: flask-type and internal-flush. All four package design concepts would withstand hydrostatic pressure of 9,600 psi, with factor safety 2.0. The combined loading condition includes axial tension and compression from the weight of a string or stack of packages in the disposal borehole, either during lower and emplacement of a string, or after stacking of multiple packages emplaced singly. Combined loading also includes bending that may occur during emplacement, particularly for a string of packages threaded together. Flask-type packages would be fabricated and heat-treated, if necessary, before loading waste. The fill port would be narrower than the waste cavity inner diameter, so the flask type is suitable for directly loading bulk granular waste, or loading slim waste canisters (e.g., containing Cs/Sr capsules) that fit through the port. The fill port would be sealed with a tapered, threaded plug, with a welded cover plate (welded after loading). Threaded connections between packages and between packages and a drill string, would be standard drill pipe threads. The internal flush packaging concepts would use semi-flush oilfield tubing, which is internally flush but has a slight external upset at the joints. This type of tubing can be obtained with premium, low-profile threaded connections at each end. The internal-flush design would be suitable for loading waste that arrives from the originating site in weld-sealed, cylindrical canisters. Internal, tapered plugs with sealing filet welds would seal the tubing at each end. The taper would be precisely machined onto both the tubing and the plug, producing a metal-metal sealing surface that is compressed as the package is subjected to hydrostatic pressure. The lower plug would be welded in place before loading, while the upper plug would be placed and welded after loading. Conceptual Waste Packaging Options for Deep Borehole Disposal July 30, 2015 iv Threaded connections between packages would allow emplacement singly or in strings screwed together at the disposal site. For emplacement on a drill string the drill pipe would be connected directly into the top package of a string (using an adapter sub to mate with premium semi-flush tubing threads). Alternatively, for wireline emplacement the same package designs could be emplaced singly using a sub with wireline latch, on the upper end. Threaded connections on the bottom of the lowermost package would allow attachment of a crush box, instrumentation, etc.« less

  5. TYPE A FISSILE PACKAGING FOR AIR TRANSPORT PROJECT OVERVIEW

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Eberl, K.; Blanton, P.

    2013-10-11

    This paper presents the project status of the Model 9980, a new Type A fissile packaging for use in air transport. The Savannah River National Laboratory (SRNL) developed this new packaging to be a light weight (<150-lb), drum-style package and prepared a Safety Analysis for Packaging (SARP) for submission to the DOE/EM. The package design incorporates unique features and engineered materials specifically designed to minimize packaging weight and to be in compliance with 10CFR71 requirements. Prototypes were fabricated and tested to evaluate the design when subjected to Normal Conditions of Transport (NCT) and Hypothetical Accident Conditions (HAC). An overview ofmore » the design details, results of the regulatory testing, and lessons learned from the prototype fabrication for the 9980 will be presented.« less

  6. Packaged die heater

    DOEpatents

    Spielberger, Richard; Ohme, Bruce Walker; Jensen, Ronald J.

    2011-06-21

    A heater for heating packaged die for burn-in and heat testing is described. The heater may be a ceramic-type heater with a metal filament. The heater may be incorporated into the integrated circuit package as an additional ceramic layer of the package, or may be an external heater placed in contact with the package to heat the die. Many different types of integrated circuit packages may be accommodated. The method provides increased energy efficiency for heating the die while reducing temperature stresses on testing equipment. The method allows the use of multiple heaters to heat die to different temperatures. Faulty die may be heated to weaken die attach material to facilitate removal of the die. The heater filament or a separate temperature thermistor located in the package may be used to accurately measure die temperature.

  7. 49 CFR 173.459 - Mixing of fissile material packages with non-fissile or fissile-excepted material packages.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Mixing of fissile material packages with non... (Radioactive) Materials § 173.459 Mixing of fissile material packages with non-fissile or fissile-excepted material packages. Mixing of fissile material packages with other types of Class 7 (radioactive) materials...

  8. 49 CFR 173.459 - Mixing of fissile material packages with non-fissile or fissile-excepted material packages.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Mixing of fissile material packages with non... (Radioactive) Materials § 173.459 Mixing of fissile material packages with non-fissile or fissile-excepted material packages. Mixing of fissile material packages with other types of Class 7 (radioactive) materials...

  9. 49 CFR 173.459 - Mixing of fissile material packages with non-fissile or fissile-excepted material packages.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Mixing of fissile material packages with non... (Radioactive) Materials § 173.459 Mixing of fissile material packages with non-fissile or fissile-excepted material packages. Mixing of fissile material packages with other types of Class 7 (radioactive) materials...

  10. 49 CFR 173.459 - Mixing of fissile material packages with non-fissile or fissile-excepted material packages.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Mixing of fissile material packages with non... (Radioactive) Materials § 173.459 Mixing of fissile material packages with non-fissile or fissile-excepted material packages. Mixing of fissile material packages with other types of Class 7 (radioactive) materials...

  11. 49 CFR 173.459 - Mixing of fissile material packages with non-fissile or fissile-excepted material packages.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Mixing of fissile material packages with non... (Radioactive) Materials § 173.459 Mixing of fissile material packages with non-fissile or fissile-excepted material packages. Mixing of fissile material packages with other types of Class 7 (radioactive) materials...

  12. Effects of packaging materials on storage quality of peanut kernels

    PubMed Central

    Fu, Xiaoji; Xing, Shengping; Xiong, Huiwei; Min, Hua; Zhu, Xuejing; He, Jialin; Mu, Honglei

    2018-01-01

    In order to obtain optimum packaging materials for peanut kernels, the effects of four types of packaging materials on peanut storage quality (coat color, acid value, germination rate, relative damage, and prevention of aflatoxin contamination) were examined. The results showed that packaging materials had a major influence on peanut storage quality indexes. The color of the peanut seed coat packaged in the polyester/aluminum/polyamide/polyethylene (PET/AL/PA/PE) composite film bag did not change significantly during the storage period. Color deterioration was slower with polyamide/polyethylene (PA/PE) packaging materials than with polyethylene (PE) film bags and was slower in PE bags than in the woven bags. The use of PET/AL/PA/PE and PA/PE bags maintained peanut quality and freshness for more than one year and both package types resulted in better germination rates. There were significant differences between the four types of packaging materials in terms of controlling insect pests. The peanuts packaged in the highly permeable woven bags suffered serious invasion from insect pests, while both PET/AL/PA/PE and PA/PE bags effectively prevented insect infection. Peanuts stored in PET/AL/PA/PE and PA/PE bags were also better at preventing and controlling aflatoxin contamination. PMID:29518085

  13. Combustion Gas Properties I-ASTM Jet a Fuel and Dry Air

    NASA Technical Reports Server (NTRS)

    Jones, R. E.; Trout, A. M.; Wear, J. D.; Mcbride, B. J.

    1984-01-01

    A series of computations was made to produce the equilibrium temperature and gas composition for ASTM jet A fuel and dry air. The computed tables and figures provide combustion gas property data for pressures from 0.5 to 50 atmospheres and equivalence ratios from 0 to 2.0.

  14. 77 FR 7011 - Safety Standard for Infant Swings

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-10

    ... JPMA as compliant with the ASTM voluntary infant swing standard. C. Infant Swings and the ASTM... positioned in the swing seat. c. Description of Proposed Changes The shoulder strap requirement is intended... swing fails the test. c. Description of Proposed Changes The proposed rule would make two changes to the...

  15. ASTM Validates Air Pollution Test Methods

    ERIC Educational Resources Information Center

    Chemical and Engineering News, 1973

    1973-01-01

    The American Society for Testing and Materials (ASTM) has validated six basic methods for measuring pollutants in ambient air as the first part of its Project Threshold. Aim of the project is to establish nationwide consistency in measuring pollutants; determining precision, accuracy and reproducibility of 35 standard measuring methods. (BL)

  16. Novel studies of non-aqueous volatiles in lint Cotton moisture tests by complementary thermal methods

    USDA-ARS?s Scientific Manuscript database

    Moisture affects economical and rheological properties of cotton, making its accurate determination important. A significant difference in moisture contents between the current and most cited standard oven drying ASTM method (ASTM D 2495, SOD) and volumetric Karl Fischer Titration (KFT) has been est...

  17. Spray drift reduction test method correlation

    USDA-ARS?s Scientific Manuscript database

    ASTM Standard E609 Terminology Relating to Pesticides defines drift as “The physical movement of an agrochemical through the air at the time of application or soon thereafter to any non or off target site.” Since there are many commercial tank mix adjuvants designed to reduce spray drift, ASTM esta...

  18. Methods to Use Surface Infiltration Tests in Permeable Pavement Systems to Determine Maintenance Frequency

    EPA Science Inventory

    Currently, there is limited guidance on selecting test sites to measure surface infiltration rates in permeable pavement systems to determine maintenance frequency. The ASTM method (ASTM C1701) for measuring infiltration rate of in-place pervious concrete suggest to either (1) p...

  19. 40 CFR 60.17 - Incorporations by reference.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... (C267-01), U.S. EPA, Research Triangle Park, NC or at the National Archives and Records Administration... Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428...) ASTM D86-96, Standard Test Method for Distillation of Petroleum Products (Approved April 10, 1996), IBR...

  20. Development of the Microstructure Based Stochastic Life Prediction Models

    DTIC Science & Technology

    1991-06-27

    sizes and shapes of the recrystallized and unrecrystallized grains and also measure sizes of subgrains. We will also determine the degree of...J. Lankford et al., STP 811, ASTM STP 811. ASTM, 1983. 5. M. R. James and W. L. Morris, "The Role of Microplastic Deformation in Fatigue Crack

  1. 46 CFR 114.600 - Incorporation by reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Conshohocken, PA 19428-2959 ASTM B 96-93, Standard Specification for Copper-Silicon Alloy Plate, Sheet, Strip... Operating Salt Spray (Fog) Apparatus 114.400 ASTM B 122/B 122M-95, Standard Specification for Copper-Nickel-Tin Alloy , Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and...

  2. 46 CFR 114.600 - Incorporation by reference.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Conshohocken, PA 19428-2959 ASTM B 96-93, Standard Specification for Copper-Silicon Alloy Plate, Sheet, Strip... Operating Salt Spray (Fog) Apparatus 114.400 ASTM B 122/B 122M-95, Standard Specification for Copper-Nickel-Tin Alloy , Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and...

  3. 30 CFR 75.1900 - Definitions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... Wilson Blvd., Room 2352, Arlington, Virginia 22209-3939; or at the National Archives and Records...

  4. 30 CFR 75.1900 - Definitions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... Wilson Blvd., Room 2352, Arlington, Virginia 22209-3939; or at the National Archives and Records...

  5. 30 CFR 75.1900 - Definitions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... Wilson Blvd., Room 2352, Arlington, Virginia 22209-3939; or at the National Archives and Records...

  6. 30 CFR 75.1900 - Definitions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... serve its intended function for 1 hour when subjected to a fire test incorporating an ASTM E119-88 time/temperature heat input, or equivalent. The publication ASTM E119-88 “Standard Test Methods for Fire Tests of... Wilson Blvd., Room 2352, Arlington, Virginia 22209-3939; or at the National Archives and Records...

  7. 19 CFR 151.12 - Accreditation of commercial laboratories.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

  8. 19 CFR 151.12 - Accreditation of commercial laboratories.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

  9. 19 CFR 151.12 - Accreditation of commercial laboratories.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

  10. 19 CFR 151.12 - Accreditation of commercial laboratories.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

  11. 19 CFR 151.12 - Accreditation of commercial laboratories.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ..., published by such organizations as the American Society for Testing and Materials (ASTM) and the American... American Society for Testing and Materials (ASTM) E548 (Standard Guide for General Criteria Used for... bachelor's degree in science or have two years related experience in an analytical laboratory. (g) How will...

  12. 40 CFR 260.11 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...). (7) ASTM E 168-88, “Standard Practices for General Techniques of Infrared Quantitative Analysis,” IBR...-Visible Quantitative Analysis,” IBR approved for § 264.1063. (9) ASTM E 260-85, “Standard Practice for..., Research Triangle Park, NC. (1) “Screening Procedures for Estimating the Air Quality Impact of Stationary...

  13. 40 CFR 260.11 - References.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...). (7) ASTM E 168-88, “Standard Practices for General Techniques of Infrared Quantitative Analysis,” IBR...-Visible Quantitative Analysis,” IBR approved for § 264.1063. (9) ASTM E 260-85, “Standard Practice for..., Research Triangle Park, NC. (1) “Screening Procedures for Estimating the Air Quality Impact of Stationary...

  14. 40 CFR 260.11 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...). (7) ASTM E 168-88, “Standard Practices for General Techniques of Infrared Quantitative Analysis,” IBR...-Visible Quantitative Analysis,” IBR approved for § 264.1063. (9) ASTM E 260-85, “Standard Practice for..., Research Triangle Park, NC. (1) “Screening Procedures for Estimating the Air Quality Impact of Stationary...

  15. 40 CFR 1065.1010 - Reference materials.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... for Aviation Turbine Fuels, IBR approved for § 1065.701. (10) ASTM D1837-02a (Reapproved 2007...), IBR approved for § 1065.720. (19) ASTM D2880-03, Standard Specification for Gas Turbine Fuel Oils, IBR... Fuels and Aviation Turbine Fuels By Supercritical Fluid Chromatography, IBR approved for § 1065.703. (26...

  16. 40 CFR 1065.1010 - Reference materials.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... for Aviation Turbine Fuels, IBR approved for § 1065.701. (10) ASTM D1837-02a (Reapproved 2007...), IBR approved for § 1065.720. (19) ASTM D2880-03, Standard Specification for Gas Turbine Fuel Oils, IBR... Fuels and Aviation Turbine Fuels By Supercritical Fluid Chromatography, IBR approved for § 1065.703. (26...

  17. Novel food packaging systems with natural antimicrobial agents.

    PubMed

    Irkin, Reyhan; Esmer, Ozlem Kizilirmak

    2015-10-01

    A new type of packaging that combines food packaging materials with antimicrobial substances to control microbial surface contamination of foods to enhance product microbial safety and to extend shelf-life is attracting interest in the packaging industry. Several antimicrobial compounds can be combined with different types of packaging materials. But in recent years, since consumer demand for natural food ingredients has increased because of safety and availability, these natural compounds are beginning to replace the chemical additives in foods and are perceived to be safer and claimed to alleviate safety concerns. Recent research studies are mainly focused on the application of natural antimicrobials in food packaging system. Biologically derived compounds like bacteriocins, phytochemicals, enzymes can be used in antimicrobial food packaging. The aim of this review is to give an overview of most important knowledge about application of natural antimicrobial packagings with model food systems and their antimicrobial effects on food products.

  18. Studies on Stress Corrosion Cracking of Super 304H Austenitic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Prabha, B.; Sundaramoorthy, P.; Suresh, S.; Manimozhi, S.; Ravishankar, B.

    2009-12-01

    Stress corrosion cracking (SCC) is a common mode of failure encountered in boiler components especially in austenitic stainless steel tubes at high temperature and in chloride-rich water environment. Recently, a new type of austenitic stainless steels called Super304H stainless steel, containing 3% copper is being adopted for super critical boiler applications. The SCC behavior of this Super 304H stainless steel has not been widely reported in the literature. Many researchers have studied the SCC behavior of steels as per various standards. Among them, the ASTM standard G36 has been widely used for evaluation of SCC behavior of stainless steels. In this present work, the SCC behavior of austenitic Fe-Cr-Mn-Cu-N stainless steel, subjected to chloride environments at varying strain conditions as per ASTM standard G36 has been studied. The environments employed boiling solution of 45 wt.% of MgCl2 at 155 °C, for various strain conditions. The study reveals that the crack width increases with increase in strain level in Super 304H stainless steels.

  19. Transmission Loss and Absorption of Corrugated Core Sandwich Panels With Embedded Resonators

    NASA Technical Reports Server (NTRS)

    Allen, Albert R.; Schiller, Noah H.; Zalewski, Bart F.; Rosenthal, Bruce N.

    2014-01-01

    The effect of embedded resonators on the diffuse field sound transmission loss and absorption of composite corrugated core sandwich panels has been evaluated experimentally. Two 1.219 m × 2.438 m panels with embedded resonator arrangements targeting frequencies near 100 Hz were evaluated using non-standard processing of ASTM E90-09 acoustic transmission loss and ASTM C423-09a room absorption test measurements. Each panel is comprised of two composite face sheets sandwiching a corrugated core with a trapezoidal cross section. When inlet openings are introduced in one face sheet, the chambers within the core can be used as embedded acoustic resonators. Changes to the inlet and chamber partition locations allow this type of structure to be tuned for targeted spectrum passive noise control. Because the core chambers are aligned with the plane of the panel, the resonators can be tuned for low frequencies without compromising the sandwich panel construction, which is typically sized to meet static load requirements. Absorption and transmission loss performance improvements attributed to opening the inlets were apparent for some configurations and inconclusive for others.

  20. Perfect sound insulation property of reclaimed waste tire rubber

    NASA Astrophysics Data System (ADS)

    Ubaidillah, Harjana, Yahya, Iwan; Kristiani, Restu; Muqowi, Eki; Mazlan, Saiful Amri

    2016-03-01

    This article reports an experimental investigation of sound insulation and absorption performance of a materials made of reclaimed ground tire rubber which is known as un-recyclable thermoset. The bulk waste tire is processed using single step recycling methods namely high-pressure high-temperature sintering (HPHTS). The bulk waste tire is simply placed into a mold and then a pressure load of 3 tons and a heating temperature of 200°C are applied to the mold. The HPHTS conducted for an hour and then it is cooled in room temperature. The resulted product is then evaluated the acoustical properties namely sound transmission loss (STL) and sound absorption coefficient using B&K Tube Kit Type 4206-T based on ISO 10534-2, ASTM E1050 and ASTM E2611. The sound absorption coefficient is found about 0.04 until 0.08 while STL value ranges between 50 to 60 dB. The sound absorption values are found to be very low (<0.1), while the average STL is higher than other elastomeric matrix found in previous work. The reclaimed tire rubber through HPHTS technique gives good soundproof characteristic.

  1. Sensitization Behavior of Type 409 Ferritic Stainless Steel: Confronting DL-EPR Test and Practice W of ASTM A763

    NASA Astrophysics Data System (ADS)

    Scalise, Taís Campos; de Oliveira, Mara Cristina Lopes; Sayeg, Isaac Jamil; Antunes, Renato Altobelli

    2014-06-01

    Stainless steels employed for manufacturing automotive exhaust systems must withstand severe thermal cycles, corrosive environment due to urea decomposition, and welding operations. AISI 409 ferritic stainless steel can be considered a low-cost alternative for this application. However, depending on the manufacturing conditions during welding cycles, this material can be sensitized due to the precipitation of chromium carbides at grain boundaries. In this work, the intergranular corrosion resistances of the AISI 409 ferritic stainless steel were evaluated after annealing at 300, 500, and 700 °C for 2, 4, and 6 h. Solution-annealed samples were also tested for comparison purposes. Two methodologies were used to assess the sensitization behavior of the 409 stainless steel samples: the first one was based on the ASTM A763 (practice W), while the second one was based on the double-loop electrochemical potentiodynamic reactivation test. It was possible to identify that the annealing treatment performed at 500 °C was more critical to the occurrence of intergranular corrosion.

  2. Packaging's Contribution for the Effectiveness of the Space Station's Food Service Operation

    NASA Technical Reports Server (NTRS)

    Rausch, B. A.

    1985-01-01

    Storage limitations will have a major effect on space station food service. For example: foods with low bulk density such as ice cream, bread, cake, standard type potato chips and other low density snacks, flaked cereals, etc., will exacerbate the problem of space limitations; package containers are inherently volume consuming and refuse creating; and the useful observation that the optimum package is no package at all leads to the tentative conclusion that the least amount of packaging per unit of food, consistent with storage, aesthetics, preservation, cleanliness, cost and disposal criteria, is the most practical food package for the space station. A series of trade offs may have to be made to arrive at the most appropriate package design for a particular type of food taking all the criteria into account. Some of these trade offs are: single serve vs. bulk; conventional oven vs. microwave oven; nonmetallic aseptically vs. non-aseptically packaged foods; and comparison of aseptic vs. nonaseptic food packages. The advantages and disadvantages are discussed.

  3. FABRICATION AND DEPLOYMENT OF THE 9979 TYPE AF RADIOACTIVE WASTE PACKAGING FOR THE DEPARTMENT OF ENERGY

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Blanton, P.; Eberl, K.

    2013-10-10

    This paper summarizes the development, testing, and certification of the 9979 Type A Fissile Packaging that replaces the UN1A2 Specification Shipping Package eliminated from Department of Transportation (DOT) 49 CFR 173. The DOT Specification Package was used for many decades by the U.S. nuclear industry as a fissile waste container until its removal as an authorized container by DOT. This paper will discuss stream lining procurement of high volume radioactive material packaging manufacturing, such as the 9979, to minimize packaging production costs without sacrificing Quality Assurance. The authorized content envelope (combustible and non-combustible) as well as planned content envelope expansionmore » will be discussed.« less

  4. 49 CFR 172.310 - Class 7 (radioactive) materials.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... packaging, in letters at least 13 mm (0.5 in) high, with the words “TYPE IP-1,” “TYPE IP-2,” “TYPE IP-3,” “TYPE A,” “TYPE B(U)” or “TYPE B(M),” as appropriate. A package which does not conform to Type IP-1, Type IP-2, Type IP-3, Type A, Type B(U) or Type B(M) requirements may not be so marked. (c) Each...

  5. 49 CFR 172.310 - Class 7 (radioactive) materials.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... packaging, in letters at least 13 mm (0.5 in) high, with the words “TYPE IP-1,” “TYPE IP-2,” “TYPE IP-3,” “TYPE A,” “TYPE B(U)” or “TYPE B(M),” as appropriate. A package which does not conform to Type IP-1, Type IP-2, Type IP-3, Type A, Type B(U) or Type B(M) requirements may not be so marked. (c) Each...

  6. The breaking load method - Results and statistical modification from the ASTM interlaboratory test program

    NASA Technical Reports Server (NTRS)

    Colvin, E. L.; Emptage, M. R.

    1992-01-01

    The breaking load test provides quantitative stress corrosion cracking data by determining the residual strength of tension specimens that have been exposed to corrosive environments. Eight laboratories have participated in a cooperative test program under the auspices of ASTM Committee G-1 to evaluate the new test method. All eight laboratories were able to distinguish between three tempers of aluminum alloy 7075. The statistical analysis procedures that were used in the test program do not work well in all situations. An alternative procedure using Box-Cox transformations shows a great deal of promise. An ASTM standard method has been drafted which incorporates the Box-Cox procedure.

  7. Summary: Update to ASTM Guide E 1523 to Charge Control and Charge Referencing Techniques in X-ray Photoelectron Spectroscopy

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Baer, Donald R.

    2005-04-22

    An updated version of the ASTM guide E1523 to the methods to charge control and charge referencing techniques in x-ray photoelectron spectroscopy has been released by ASTM. The guide is meant to acquaint x-ray photoelectron spectroscopy (XPS) users with the various charge control and charge referencing techniques that are and have been used in the acquisition and interpretation of XPS data from surfaces of insulating specimens. The current guide has been expanded to include new references as well as recommendations for reporting information on charge control and charge referencing. The previous version of the document had been published in 1997.

  8. 49 CFR 178.935 - Standards for wooden Large Packagings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Packagings. (i) Natural wood used in the construction of Large Packagings must be well-seasoned, commercially...) Reconstituted wood used in the construction of Large Packagings must be water resistant reconstituted wood such... Packaging types are designated: (1) 50C natural wood. (2) 50D plywood. (3) 50F reconstituted wood. (b...

  9. 24 CFR 3280.703 - Minimum standards.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless—ASTM A53-93. Standard Specification for Electric-Resistance-Welded Coiled Steel Tubing for Gas and Fuel Oil Lines—ASTM A539-1999. Pipe Threads, General Purpose (Inch)—ANSI/ASME B1.20.1-1983. Welding and Seamless Wrought...

  10. 40 CFR 98.324 - Monitoring and QA/QC requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Procedures and Inspection Tracking System Handbook Number: PH-08-V-1, January 1, 2008 (incorporated by... paragraphs (d)(1) through (d)(2) of this section. (1) ASTM D1945-03, Standard Test Method for Analysis of... Reformed Gas by Gas Chromatography; ASTM D4891-89 (Reapproved 2006), Standard Test Method for Heating Value...

  11. 40 CFR 98.324 - Monitoring and QA/QC requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Procedures and Inspection Tracking System Handbook Number: PH-08-V-1, January 1, 2008 (incorporated by... paragraphs (d)(1) through (d)(2) of this section. (1) ASTM D1945-03, Standard Test Method for Analysis of... Reformed Gas by Gas Chromatography; ASTM D4891-89 (Reapproved 2006), Standard Test Method for Heating Value...

  12. 40 CFR 98.324 - Monitoring and QA/QC requirements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Procedures and Inspection Tracking System Handbook Number: PH-08-V-1, January 1, 2008 (incorporated by... ASTM D1945-03, Standard Test Method for Analysis of Natural Gas by Gas Chromatography; ASTM D1946-90... (Reapproved 2006), Standard Test Method for Heating Value of Gases in Natural Gas Range by Stoichiometric...

  13. 40 CFR 92.5 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... § 92.113 ASTM D 1945-91, Standard Test Method for Analysis of Natural Gas by Gas Chromatography § 92... Supercritical Fluid Chromatography § 92.113 ASTM E 29-93a, Standard Practice for Using Significant Digits in....119 SAE Recommended Practice J244, Measurement of Intake Air or Exhaust Gas Flow of Diesel Engines...

  14. 46 CFR 114.600 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... for Building and Classing Steel Vessels Under 61 Meters (200 Feet) in Length, 1983 116.300 Rules for...) Apparatus 114.400 ASTM B 122/B 122M-95, Standard Specification for Copper-Nickel-Tin Alloy , Copper-Nickel..., Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester 114.400 ASTM D 635-97, Standard...

  15. Analytical methods for determining fire resistance of timber members

    Treesearch

    Robert H. White

    2008-01-01

    The fire resistance ratings of wood members and assemblies, as of other materials, have traditionally been obtained by testing the assembly in a furnace in accordance with ASTM International (ASTM) Standard E119, International Organization for Standardization (ISO) Standard 834, and similar standards. These ratings are published in listings, such as Underwriters...

  16. Standard specification for carbon and alloy steel nuts. ASTM standard

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    This specification is under the jurisdiction of ASTM Committee F-16 on Fasteners and is the responsibility of Subcommittee F16.02 on Steel Bolts, Nuts, Rivets, and Washers. Current edition approved Dec. 10, 1997. Published July 1998. Originally published as A 563-66. Last previous edition A 563-96.

  17. 29 CFR Appendix A to Subpart S of... - References for Further Information

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (Classified) Locations. ASTM D3176-1989 (2002) Standard Practice for Ultimate Analysis of Coal and Coke. ASTM D3180-1989 (2002) Standard Practice for Calculating Coal and Coke Analyses from As-Determined to... for the Storage and Handling of Cellulose Nitrate Film. NFPA 58-2004 Liquefied Petroleum Gas Code...

  18. 40 CFR 63.14 - Incorporations by reference.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...., Washington, DC, and at the EPA Library (MD-35), U.S. EPA, Research Triangle Park, North Carolina. For... (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428-2959, Telephone (610... following Web site: http://www.proquest.com. (1) ASTM D523-89, Standard Test Method for Specular Gloss, IBR...

  19. 40 CFR 63.14 - Incorporations by reference.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...., Washington, DC, and at the EPA Library (MD-35), U.S. EPA, Research Triangle Park, North Carolina. For... (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428-2959; or ProQuest, 300 North Zeeb Road, Ann Arbor, MI 48106. (1) ASTM D523-89, Standard Test Method for Specular Gloss, IBR...

  20. Laboratory Characterization of Solid Grade SW Brick

    DTIC Science & Technology

    2007-08-01

    Society for Testing and Materials (ASTM) D 2216 (ASTM 2002e). Based on the appropriate values of posttest water content, wet density, and an assumed...strain path (UX/SP) tests. In addition to the mechanical property tests, nondestructive pulse-velocity measurements were performed on each specimen...Figure 3. Spring-arm lateral deformeter mounted on test specimen

  1. 46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

  2. 46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

  3. 46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

  4. 46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

  5. 46 CFR 160.077-19 - Approval Testing-Recreational Hybrid PFD's.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... distribution, and inflation medium retention test, UL 1517, sections 18 and 19, except: (i) Recreational hybrid... Method Standard 191, or ASTM D 751 (incorporated by reference, see § 160.077-5). (4) Permeability. The permeability of chamber materials must be determined according to ASTM D 1434 (incorporated by reference, see...

  6. 21 CFR 175.270 - Poly(vinyl fluoride) resins.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ...(vinyl fluoride) basic resins have an intrinsic viscosity of not less than 0.75 deciliter per gram as determined by ASTM method D1243-79, “Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride... (ASTM method D1243-79, “Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers...

  7. 45 CFR 170.299 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., MI 48104; Telephone (734) 677-7777 or http://www.hl7.org/. (1) Health Level Seven Standard Version 2..., PA, 19428-2959 USA; Telephone (610) 832-9585 or http://www.astm.org/. (1) ASTM E2369-05: Standard...) 477-1000; and Facsimile (480) 767-1042 or http://www.ncpdp.org. (1) National Council for Prescription...

  8. Collection Efficiencies of Various Airborne Spray Flux Samplers Used in Aerial Application Research

    DTIC Science & Technology

    2008-01-01

    Nonimaging Light-Scattering Instruments 21. Droplet sizing data measured included volume median diameter DV0.5, the 10 and 90 % diameters DV0.1 and DV0.9...Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments,” Annual Book of ASTM Stan- dards, ASTM

  9. Standard specification for nuclear grade hafnium oxide pellets. ASTM standard

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    This specification is under the jurisdiction of ASTM Committee C-26 on Nuclear Fuel Cycle and is the direct responsibility of Subcommittee C26.03 on Neutron Absorber Materials Specifications. Current edition approved May 10, 1997. Published May 1998. Originally published as C 1076-87. Last previous edition C 1076-92.

  10. Effect of Decay on Ultrasonic Velocity and Attenuation Measurements in Wood

    Treesearch

    Megan McGovern; Adam Senalik; George Chen; Frank C. Beall; Henrique Reis

    2013-01-01

    The percentage mass loss of loblolly pine (pinus taeda) wood cube specimens exposed to Gloeophyllum fungus (Gloeophyllum trabeum) for increasing periods of time ranging from 1 to 12 weeks was recorded after being subjected to controlled decay following ASTM International standard ASTM D 1423-99. The specimens’ corresponding volume...

  11. 40 CFR Appendix A to Subpart II of... - VOC Data Sheet 1

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES (CONTINUED) National Emission Standards for Shipbuilding and Ship Repair (Surface Coating) Pt. 63, Subpt. II, App. A...: (Dc)s __ g/L [] ASTM D1475-90 *[] Other 3 B. Total Volatiles: (mv)s __ Mass Percent [] ASTM D2369-93...

  12. Age-related differences in orienting attention to sound object representations.

    PubMed

    Alain, Claude; Cusimano, Madeline; Garami, Linda; Backer, Kristina C; Habelt, Bettina; Chan, Vanessa; Hasher, Lynn

    2018-06-01

    We examined the effect of age on listeners' ability to orient attention to an item in auditory short-term memory (ASTM) using high-density electroencephalography, while participants completed a delayed match-to-sample task. During the retention interval, an uninformative or an informative visual retro-cue guided attention to an item in ASTM. Informative cues speeded response times, but only for young adults. In young adults, informative retro-cues generated greater event-related potential amplitude between 450 and 650 ms at parietal sites, and an increased sustained potential over the left central scalp region, thought to index the deployment of attention and maintenance of the cued item in ASTM, respectively. Both modulations were reduced in older adults. Alpha and low beta oscillatory power suppression was greater when the retro-cue was informative than uninformative, especially in young adults. Our results point toward an age-related decline in orienting attention to the cued item in ASTM. Older adults may be dividing their attention between all items in working memory rather than selectively focusing attention on a single cued item. Copyright © 2018 Elsevier Inc. All rights reserved.

  13. Impact of heat treatment on HSS cutting tool (ASTM A600) and its behaviour during machining of mild steel (ASTM A36)

    NASA Astrophysics Data System (ADS)

    Afolalu, S. A.; Abioye, O. P.; Salawu, E. Y.; Okokpujie, I. P.; Abioye, A. A.; Omotosho, O. A.; Ajayi., O. O.

    2018-04-01

    Carburization is one the best heat treatment that responded well to hardening with Palm Kernel Shell giving the best hardness value. This work studied the influence of carburization on HSStool(ASTM A600) and its behaviour during machining of mild steel (ASTM A36). Composition of the samples (12 pieces of 180 × 12 × 12 mm) HSS tools were checked using UV-VIS spectrometer and the tools were carburized with PKS at holding temperatures and time of 800, 850, 900, 950 °C and 60,90 120 minutes using muffle furnance. The micro structural analysis, surface and core hardnessof the treated samples gave better results than the untreated samples when checked withsoft driven and optical microscope. It wasalso observed that increase in the feed rate and depth for length of cut of 50 mm significantly reduces the wear progression and thereby gave best machining time at maximum carburizing temperature and time(950 °C / 120 minutes) when it was used to cut mild steelon the lathe machine.

  14. Cyclic Polarization Behavior of ASTM A537-Cl.1 Steel in the Vapor Space Above Simulated Waste

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wiersma, B

    2004-11-01

    An assessment of the potential degradation mechanisms of Types I and II High-Level Waste (HLW) Tanks determined that pitting corrosion and stress corrosion cracking were the two most significant degradation mechanisms. Specifically, nitrate induced stress corrosion cracking was determined to be the principal degradation mechanism for the primary tank steel of non-stress relieved tanks. Controls on the solution chemistry have been in place to preclude the initiation and propagation of degradation in the tanks. However, recent experience has shown that steel not in contact with the bulk waste solution or slurry, but exposed to the ''vapor space'' above the bulkmore » waste, may be vulnerable to the initiation and propagation of degradation, including pitting and stress corrosion cracking. A program to resolve the issues associated with potential vapor space corrosion is in place. The objective of the program is to develop understanding of vapor space (VSC) and liquid/air interface (LAIC) corrosion to ensure a defensible technical basis to provide accurate corrosion evaluations with regard to vapor space and liquid/air interface corrosion (similar to current evaluations). There are several needs for a technically defensible basis with sufficient understanding to perform these evaluations. These include understanding of the (1) surface chemistry evolution, (2) corrosion response through coupon testing, and (3) mechanistic understanding through electrochemical studies. Experimentation performed in FY02 determined the potential for vapor space and liquid/air interface corrosion of ASTM A285-70 and ASTM A537-Cl.1 steels. The material surface characteristics, i.e. mill-scale, polished, were found to play a key role in the pitting response. The experimentation indicated that the potential for limited vapor space and liquid/air interface pitting exists at 1.5M nitrate solution when using chemistry controls designed to prevent stress corrosion cracking. Experimentation performed in FY03 quantified pitting rates as a function of material surface characteristics, including mill-scale and defects within the mill-scale. Testing was performed on ASTM A537-Cl.1 (normalized) steel, the material of construction of the Type III HLW tanks. The pitting rates were approximately 3 mpy for exposure above inhibited solutions, as calculated from the limited exposure times. This translates to a penetration time of 166 years for a 0.5-in tank wall provided that the pitting rate remains constant and the bulk solution chemistry is maintained within the L3 limit. The FY04 testing consisted of electrochemical testing to potentially lend insight into the surface chemistry and further understand the corrosion mechanism in the vapor space. Electrochemical testing lends insight into the corrosion processes through the determination of current potential relationships. The results of the electrochemical testing performed during FY04 are presented here.« less

  15. Paperless or vanishing society

    NASA Astrophysics Data System (ADS)

    Turner Luke, Joy

    2002-06-01

    In the 1940s color photography became available and within a few years, extremely popular. As people switched from black and white photographs made with the old metallic silver process to the new color films, pictures taken to record their lives and families began a slow disappearing act. The various color processes, coupled with the substrates they were printed on, affected their longevity, but many color photographs taken from the late 1950s through the 1970s, and even into the 1980s, faded not only when exposed to the light, but also when stored in the dark. Henry Wilhelm's excellent book 'The Permanence and Care of Color Photographs' documents this history in detail. Today we are making another transition in the storage of pictures and information. There are questions about the longevity of different types of digital storage, and also of the images printed by various types of inkjet printers, or by laser printers using colored toners. Very expensive and very beautiful works of art produced on Iris printers are appearing in art exhibitions. Some of these are referred to as Giclee prints and are offered on excellent papers. Artists are told the prints will last a lifetime; and if by change they don't it is only necessary to make another print. Henry Wilhelm has begun to test and rate these images for lightfastness; however, his test method was developed for examining longevity in colored photographs. It is of interest to find out how these prints will hold up in the tests required for fine art materials. Thus far companies producing digital inks and printers have not invested the time and money necessary to develop an American Society for Testing and Materials (ASTM) standard method for evaluating the lightfastness of digital prints. However, it is possible to use ASTM D 5383, Standard Practice for Visual Determination of the Lightfastness of Art Materials by Art Technologists, to pinpoint colors that will fade in a short time, even though the test is not as severe as ASTM D 4303, which is used to rate the lightfastness of artists's paint.

  16. Certification of alternative aviation fuels and blend components

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wilson III, George R.; Edwards, Tim; Corporan, Edwin

    2013-01-15

    Aviation turbine engine fuel specifications are governed by ASTM International, formerly known as the American Society for Testing and Materials (ASTM) International, and the British Ministry of Defence (MOD). ASTM D1655 Standard Specification for Aviation Turbine Fuels and MOD Defence Standard 91-91 are the guiding specifications for this fuel throughout most of the world. Both of these documents rely heavily on the vast amount of experience in production and use of turbine engine fuels from conventional sources, such as crude oil, natural gas condensates, heavy oil, shale oil, and oil sands. Turbine engine fuel derived from these resources and meetingmore » the above specifications has properties that are generally considered acceptable for fuels to be used in turbine engines. Alternative and synthetic fuel components are approved for use to blend with conventional turbine engine fuels after considerable testing. ASTM has established a specification for fuels containing synthesized hydrocarbons under D7566, and the MOD has included additional requirements for fuels containing synthetic components under Annex D of DS91-91. New turbine engine fuel additives and blend components need to be evaluated using ASTM D4054, Standard Practice for Qualification and Approval of New Aviation Turbine Fuels and Fuel Additives. This paper discusses these specifications and testing requirements in light of recent literature claiming that some biomass-derived blend components, which have been used to blend in conventional aviation fuel, meet the requirements for aviation turbine fuels as specified by ASTM and the MOD. The 'Table 1' requirements listed in both D1655 and DS91-91 are predicated on the assumption that the feedstocks used to make fuels meeting these requirements are from approved sources. Recent papers have implied that commercial jet fuel can be blended with renewable components that are not hydrocarbons (such as fatty acid methyl esters). These are not allowed blend components for turbine engine fuels as discussed in this paper.« less

  17. Biotribological evaluation of artificial disc arthroplasty devices: influence of loading and kinematic patterns during in vitro wear simulation.

    PubMed

    Grupp, Thomas M; Yue, James J; Garcia, Rolando; Basson, Janet; Schwiesau, Jens; Fritz, Bernhard; Blömer, Wilhelm

    2009-01-01

    Wear simulation is an essential pre-clinical method to predict the mid- and long-term clinical wear behavior of newly introduced devices for total disc arthroplasty. The main requirement of a suitable method for spinal wear simulation has to be the ability to distinguish between design concepts and allow for a direct comparison of predicate devices. The objective of our study was to investigate the influence of loading and kinematic patterns based on two different protocols for spinal wear simulation (ISO/FDIS 18192-1 (2006) and ASTM F2423-05). In vitro wear simulation was performed with six activ L lumbar artificial disc devices (Aesculap Tuttlingen, Germany). The applied kinematic pattern of movement was multidirectional for ISO (elliptic track) and unidirectional with a curvilinear shape for ASTM. Testing was done for 10 million cycles in the ISO loading mode and afterwards with the same specimens for 5 million cycles according to the ASTM protocol with a customized six-station servohydraulic spinal wear simulator (EndoLab Thansau, Germany). Gravimetrical and geometrical wear assessment, a slide track analysis correlated to an optical surface characterization, and an estimation of particle size and morphology were performed. The gravimetric wear rate for the first 10 million cycles was ISO(initial) = 2.7 +/- 0.3 mg/million cycles. During the ASTM test period (10-15 million cycles) a gravimetric wear rate of 0.14 +/- 0.06 mg/million cycles was estimated. The wear rates between the ISO and ASTM driven simulations differ substantially (approximately 20-fold) and statistical analysis demonstrates a significant difference (p < 0.001) between the test groups. The main explanation of divergency between ISO and ASTM driven wear simulations is the multidirectional pattern of movement described in the ISO document resulting in a cross-shear stress on the polyethylene material. Due to previous retrieval observations, it seems to be very unlikely that a lumbar artificial disc is loaded with a linear wear path.Testing according to ASTM F2423-05 with pure unidirectional motion does not reflect the kinematics of TDA patients' daily activities. Based on our findings it seems to be more reliable to predict the clinical wear behavior of an artificial disc replacement using the ISO/FDIS 18192-1 method.

  18. Biotribological evaluation of artificial disc arthroplasty devices: influence of loading and kinematic patterns during in vitro wear simulation

    PubMed Central

    Yue, James J.; Garcia, Rolando; Basson, Janet; Schwiesau, Jens; Fritz, Bernhard; Blömer, Wilhelm

    2008-01-01

    Wear simulation is an essential pre-clinical method to predict the mid- and long-term clinical wear behavior of newly introduced devices for total disc arthroplasty. The main requirement of a suitable method for spinal wear simulation has to be the ability to distinguish between design concepts and allow for a direct comparison of predicate devices. The objective of our study was to investigate the influence of loading and kinematic patterns based on two different protocols for spinal wear simulation (ISO/FDIS 18192-1 (2006) and ASTM F2423-05). In vitro wear simulation was performed with six activ® L lumbar artificial disc devices (Aesculap Tuttlingen, Germany). The applied kinematic pattern of movement was multidirectional for ISO (elliptic track) and unidirectional with a curvilinear shape for ASTM. Testing was done for 10 million cycles in the ISO loading mode and afterwards with the same specimens for 5 million cycles according to the ASTM protocol with a customized six-station servohydraulic spinal wear simulator (EndoLab Thansau, Germany). Gravimetrical and geometrical wear assessment, a slide track analysis correlated to an optical surface characterization, and an estimation of particle size and morphology were performed. The gravimetric wear rate for the first 10 million cycles was ISOinitial = 2.7 ± 0.3 mg/million cycles. During the ASTM test period (10–15 million cycles) a gravimetric wear rate of 0.14 ± 0.06 mg/million cycles was estimated. The wear rates between the ISO and ASTM driven simulations differ substantially (approximately 20-fold) and statistical analysis demonstrates a significant difference (p < 0.001) between the test groups. The main explanation of divergency between ISO and ASTM driven wear simulations is the multidirectional pattern of movement described in the ISO document resulting in a cross-shear stress on the polyethylene material. Due to previous retrieval observations, it seems to be very unlikely that a lumbar artificial disc is loaded with a linear wear path.Testing according to ASTM F2423-05 with pure unidirectional motion does not reflect the kinematics of TDA patients‘ daily activities. Based on our findings it seems to be more reliable to predict the clinical wear behavior of an artificial disc replacement using the ISO/FDIS 18192-1 method. PMID:19050942

  19. Death by heroin intoxication in a body pusher with an innovative packaging technique: case report and review of the literature.

    PubMed

    Visentin, Sindi; Bevilacqua, Greta; Giraudo, Chiara; Dengo, Caterina; Nalesso, Alessandro; Montisci, Massimo

    2017-11-01

    Death due to mechanical or chemical intoxication of heroin body packers, thanks to the continuous improvement in packaging techniques, are increasingly rare, and almost all the cases reported in the literature refer to drug swallowers. A case of fatal acute heroin intoxication in a body pusher with an unreported packaging technique is presented, and previous deaths due to heroin body packing are reviewed, taking into consideration imaging techniques performed, cause of death, toxicological analysis on biological and non-biological samples, as well as number, position and type of drug packages identified at the dissection of the body. The innovative packaging technique found in the present case, constituted by an external multilayer cellophane casing containing 16 smaller packages of hardened heroin powder, each one covered with cigarette paper and multiple layers of heat-sealed cellophane, was probably used to avoid both chemical complications of package rupture and to create a package with morphological and radiological features different from those reported by previous studies. Drug dealers, in fact, are continually looking for packaging methods that, besides being safer, minimize the risk of detection at the radiological examinations performed, thus increasing the number of false negative findings. The identification of new types of package is therefore important, in order to identify packages that do not have the typical radiological signs, both in order to protect the patient's health and to avoid the non-recognition of a drug carrier. Despite the presence of multilayer composition of both the smaller and the bigger external coverage, these new types of package did not guarantee the greater safety of the drug dealer. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. [Metallurgical differentiation of cobalt-chromium alloys for implants].

    PubMed

    Holzwarth, U; Thomas, P; Kachler, W; Göske, J; Schuh, A

    2005-10-01

    Cobalt Chromium alloys are used in cemented total hip or knee arthroplasty as well as in metal-on-metal bearings in total hip arthroplasty. An increasing number of publications report about (allergic) reactions to wear particles of Cobalt Chromium alloys. Reactions to nickel are more frequent in comparison to Cobalt or Chromium particles. It is well known that different kinds of Cobalt Chromium alloys contain different amounts of alloying elements; nevertheless. The aim of the current work was to compare the different Cobalt Chromium alloys according to ASTM F or ISO standards in respect to the different alloying elements. Co28Cr6Mo casting alloys according to ASTM F 75 or ISO 5832-4 as well as forging alloy types according to ASTM F 799 and ISO 5832 such as Co20Cr15W10Ni, Co35Ni20Cr, Fe40Co20Cr10Ni, Co20Cr20Ni, and Co28Cr6Mo were analyzed in respect to their element content of Co, Cr, Ni, Mo, Fe, W, and Mn. In 1935 the Cobalt based alloy "Vitallium" Co30Cr5Mo basically used in the aircraft industry was introduced into medicine. The chemical composition of this alloy based on Cobalt showed 30 wt.% Chromium and 5 wt.% Molybdenum. The differentiation using alloy names showed no Nickel information in single alloy names. The information given about different alloys can lead to an unprecise evaluation of histopathological findings in respect to alloys or alloying constituents. Therefore, implant manufacturers should give the exact information about the alloys used and adhere to European law, Euronorm 93/42/EWG.

  1. 10 CFR 71.33 - Package description.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ...) Classification as Type B(U), Type B(M), or fissile material packaging; (2) Gross weight; (3) Model number; (4... absorbers or moderators, and the atomic ratio of moderator to fissile constituents; (5) Maximum normal...

  2. Food product design: emerging evidence for food policy.

    PubMed

    Al-Hamdani, Mohammed; Smith, Steven

    2017-03-01

    The research on the impact of specific brand elements such as food descriptors and package colors is underexplored. We tested whether a "light" color and a "low-calorie" descriptor on food packages gain favorable consumer perception ratings as compared with regular packages. Our online experiment recruited 406 adults in a 3 (product type: Chips versus Juice versus Yoghurt) × 2 (descriptor type: regular versus low-calorie) × 2 (color type: regular versus light) mixed design. Dependent variables were sensory (evaluations of the product's nutritional value and quality), product-based (evaluations of the product's physical appeal), and consumer-based (evaluations of the potential consumers of the product) scales. "Low-calorie" descriptors were found to increase sensory ratings as compared with regular descriptors and light-colored packages received higher product-based ratings as compared with their regular-colored counterparts. Food package color and descriptors present a promising venue for understanding preventative measures against obesity.[Formula: see text].

  3. 9977 TYPE B PACKAGING INTERNAL DATA COLLECTION FEASIBILITY TESTING - MAGNETIC FIELD COMMUNICATIONS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Shull, D.

    2012-06-18

    The objective of this report is to document the findings from proof-of-concept testing performed by the Savannah River National Laboratory (SRNL) R&D Engineering and Visible Assets, Inc. for the DOE Packaging Certification Program (PCP) to determine if RuBee (IEEE 1902.1) tags and readers could be used to provide a communication link from within a drum-style DOE certified Type B radioactive materials packaging. A Model 9977 Type B Packaging was used to test the read/write capability and range performance of a RuBee tag and reader. Testing was performed with the RuBee tags placed in various locations inside the packaging including insidemore » the drum on the outside of the lid of the containment vessel and also inside of the containment vessel. This report documents the test methods and results. A path forward will also be recommended.« less

  4. Types, production and assessment of biobased food packaging materials

    USDA-ARS?s Scientific Manuscript database

    Food packaging performs an essential function, but packaging materials can have a negative impact on the environment. This book describes the latest advances in bio-based food packaging materials. Book provides a comprehensive review on bio-based, biodegradable and recycled materials and discusses t...

  5. Annular Pulse Shaping Technique for Large-Diameter Kolsky Bar Experiments on Concrete

    DTIC Science & Technology

    2014-10-01

    practiced by a number of Kolsky bar researchers on a variety of brittle materials such as glass , ceramics , and ceramic composites using relatively... glass under compression/shear loading: Experiments. J Am Ceram Soc 90:2556–2562 37. Nie X, Sanborn B, Weerasooriya T, Chen W (2012) Inertia effects in...is comprised of ASTM type I/II cement [2], Grade 120 Slag cement [5] and Class F fly ash [4]. The 1344 Exp Mech (2014) 54:1343–1354 Author’s personal

  6. Hydrogen Tank Project Q2 Report - FY 11

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Johnson, Kenneth I.; Alvine, Kyle J.; Skorski, Daniel C.

    2011-05-15

    Quarterly report that represents PNNL's results of HDPE, LDPE, and industrial polymer materials testing. ASTM D638 type 3 samples were subjected to a high pressure hydrogen environment between 3000 and 4000 PSI. These samples were tested using an instron load frame and were analyzed using a proprietary set of excel macros to determine trends in data. The development of an in-situ high pressure hydrogen tensile testing apparatus is discussed as is the stress modeling of the carbon fiber tank exterior.

  7. Energetic Materials Effects on Essential Soil Processes: Decomposition of Orchard Grass (Dactylis glomerata) Litter in Soil Contaminated with Energetic Materials

    DTIC Science & Technology

    2014-02-01

    moisture level of 14% dry soil mass was maintained for the duration of the study by weekly additions of ASTM Type I water. Soil samples were collected...maintain the initial soil moisture level. One cluster of Orchard grass straw was harvested from a set of randomly selected replicate containers...decomposition is among the most integrating processes within the soil ecosystem because it involves complex interactions of soil microbial, plant , and

  8. 40 CFR 98.324 - Monitoring and QA/QC requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Tracking System Handbook Number: PH-08-V-1, January 1, 2008 (incorporated by reference, see § 98.7). You... paragraphs (d)(1) through (d)(2) of this section. (1) ASTM D1945-03, Standard Test Method for Analysis of... Reformed Gas by Gas Chromatography; ASTM D4891-89 (Reapproved 2006), Standard Test Method for Heating Value...

  9. Performance of portland limestone cements : cements designed to be more sustainable that include up to 15% limestone addition.

    DOT National Transportation Integrated Search

    2013-11-01

    In 2009, ASTM and AASHTO permitted the use of up to 5% interground limestone in ordinary portland cement (OPC) as a part of ASTM : C150/AASHTO M85. When this project was initiated a new proposal was being discussed that would enable up to 15% intergr...

  10. 46 CFR 56.60-1 - Acceptable materials and specifications (replaces 123 and Table 126.1 in ASME B31.1).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., and fittings when it receives certification of their mechanical properties. Without this certification... certifying that the mechanical properties at room temperature specified in ASTM A 520 (incorporated by... manufacturer certifying that the mechanical properties for A192 in ASTM A 520 have been met. Without this...

  11. Deriving allowable properties of lumber : a practical guide for interpretation of ASTM standards

    Treesearch

    Alan Bendtsen; William L. Galligan

    1978-01-01

    The ASTM standards for establishing clear wood mechanical properties and for deriving structural grades and related allowable properties for visually graded lumber can be confusing and difficult for the uninitiated to interpret. This report provides a practical guide to using these standards for individuals not familiar with their application. Sample stress...

  12. 75 FR 24711 - Food and Drug Administration Modernization Act of 1997: Modifications to the List of Recognized...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-05

    ... newer version Indicators - Guidance for the Selection, Use and Interpretation of Results I. Tissue Engineering 15-6 15-16 ASTM F2450-09 Standard Guide for Assessing Withdrawn and replaced Microstructure of Polymeric Scaffolds for with newer version Use in Tissue Engineered Medical Products\\1\\ 15-9 15-17 ASTM...

  13. 46 CFR 30.10-27 - Flashpoint-TB/ALL.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... gives off a flammable vapor when heated in an open-cup tester. For the purpose of the regulations in... with an open-cup tester, as follows: Table 30.10-27—Equivalent Flashpoints [In degrees Farenheit] Open-cup tester Tag closed-cup tester (A.S.T.M.) Pensky-Martens closed tester (A.S.T.M.) 80 75 150 140 ...

  14. 46 CFR 30.10-27 - Flashpoint-TB/ALL.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... gives off a flammable vapor when heated in an open-cup tester. For the purpose of the regulations in... with an open-cup tester, as follows: Table 30.10-27—Equivalent Flashpoints [In degrees Farenheit] Open-cup tester Tag closed-cup tester (A.S.T.M.) Pensky-Martens closed tester (A.S.T.M.) 80 75 150 140 ...

  15. 24 CFR 3280.706 - Oil piping systems.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... the Standard Specification for Seamless Copper Water Tube, ASTM B88-93, or shall comply with ASTM B280... supply connection(s) shall be rigidly anchored to a structural member within 6 inches of the supply... shall be checked for oil leaks with fuel oil of the same grade that will be burned in the appliance. No...

  16. 40 CFR 60.17 - Incorporations by reference.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... (C267-01), U.S. EPA, Research Triangle Park, NC or at the National Archives and Records Administration... Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428...), 60.593(d), 60.593a(d), and 60.633(h). (8) ASTM D129-64, 78, 95, 00, Standard Test Method for Sulfur...

  17. 40 CFR 60.17 - Incorporations by reference.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... (C267-01), U.S. EPA, Research Triangle Park, NC or at the National Archives and Records Administration... Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428...), 60.593(d), 60.593a(d), and 60.633(h). (8) ASTM D129-64, 78, 95, 00, Standard Test Method for Sulfur...

  18. Comparing the Methodologies in ASTM G198: Is There an Easy Way Out?

    Treesearch

    Samuel L. Zelinka

    2013-01-01

    ASTM(1) G198, Standard test method for determining the relative corrosion performance of driven fasteners in contact with treated wood, was accepted by consensus and published in 2011. The method has two different exposure conditions for determining fastener corrosion performance in treated wood. The first method places the wood and embedded...

  19. 40 CFR 63.14 - Incorporations by reference.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... (MD-35), U.S. EPA, Research Triangle Park, North Carolina. For information on the availability of this..., Post Office Box C700, West Conshohocken, PA 19428-2959; or ProQuest, 300 North Zeeb Road, Ann Arbor, MI 48106. (1) ASTM D523-89, Standard Test Method for Specular Gloss, IBR approved for § 63.782. (2) ASTM...

  20. 46 CFR 160.156-5 - Incorporation by reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., Standard Specification for Carbon Structural Steel, (approved May 15, 2008), IBR approved for §§ 160.156-7 and 160.156-15 (“ASTM A 36”). (2) ASTM A 276-08a, Standard Specification for Stainless Steel Bars and..., (approved October 1, 2008), Standard Specification for Stainless Steel Spring Wire, IBR approved for § 160...

  1. 46 CFR 160.156-5 - Incorporation by reference.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ..., Standard Specification for Carbon Structural Steel, (approved May 15, 2008), IBR approved for §§ 160.156-7 and 160.156-15 (“ASTM A 36”). (2) ASTM A 276-08a, Standard Specification for Stainless Steel Bars and..., (approved October 1, 2008), Standard Specification for Stainless Steel Spring Wire, IBR approved for § 160...

  2. 46 CFR 160.156-5 - Incorporation by reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 36M-08, Standard Specification for Carbon Structural Steel, (approved May 15, 2008), IBR approved for §§ 160.156-7 and 160.156-15 (“ASTM A 36”). (2) ASTM A 276-08a, Standard Specification for Stainless Steel... 313/A 313M-08, (approved October 1, 2008), Standard Specification for Stainless Steel Spring Wire, IBR...

  3. ASTM and other specifications and classifications for petroleum products and lubricants. Fifth edition

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    1989-01-01

    This book includes specifications and classifications from ASTM committees on paint and related coatings and materials; road and paving materials; wood; roofing, waterproofing and bituminous materials; rubber; soaps and other detergents; aromatic hydrocarbons and related chemicals; and electrical insulating liquids and gases. Also included are several related, important specifications and classifications from other organizations.

  4. 40 CFR 75.6 - Incorporation by reference.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D129-00, Standard Test... Information Reference Unit of the U.S. EPA, 401 M St., SW., Washington, DC and at the Library (MD-35), U.S... D4052-96 (Reapproved 2002), Standard Test Method for Density and Relative Density of Liquids by Digital...

  5. 40 CFR 75.6 - Incorporation by reference.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D129-00, Standard Test... Information Reference Unit of the U.S. EPA, 401 M St., SW., Washington, DC and at the Library (MD-35), U.S... D4052-96 (Reapproved 2002), Standard Test Method for Density and Relative Density of Liquids by Digital...

  6. 40 CFR 75.6 - Incorporation by reference.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D129-00, Standard Test... Information Reference Unit of the U.S. EPA, 401 M St., SW., Washington, DC and at the Library (MD-35), U.S... D4052-96 (Reapproved 2002), Standard Test Method for Density and Relative Density of Liquids by Digital...

  7. 40 CFR 75.6 - Incorporation by reference.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., phone: 610-832-9585, http://www.astm.org/DIGITAL_LIBRARY/index.shtml. (1) ASTM D129-00, Standard Test... Information Reference Unit of the U.S. EPA, 401 M St., SW., Washington, DC and at the Library (MD-35), U.S... D4052-96 (Reapproved 2002), Standard Test Method for Density and Relative Density of Liquids by Digital...

  8. 33 CFR 155.140 - Incorporation by reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Standards Institute, Inc. (ANSI), 25 West 43rd Street, New York, NY 10036, 212-642-4980, http://www.ansi.org..., PA 19428-2959, 610-832-9585, http://www.astm.org/: (1) ASTM F 631-93, Standard Guide for Collecting..., London SE1 7SR, United Kingdom, http://www.imo.org/: (1) Resolution A.535(13), Recommendations on...

  9. Effect of packaging atmospheres on storage quality characteristics of heavily marbled beef longissimus steaks.

    PubMed

    Yang, Xiaoyin; Zhang, Yimin; Zhu, Lixian; Han, Mingshan; Gao, Shujuan; Luo, Xin

    2016-07-01

    The objective of this study was to investigate the effects of modified atmosphere packaging (MAP) systems on shelf-life and quality of beef steaks with high marbling. Four packaging types were used including 80% O2 MAP (80% O2+20% CO2), 50% O2 MAP (50% O2+30% CO2+20% N2), carbon monoxide MAP (0.4% CO+30% CO2+69.6% N2) and vacuum packaging (VP). Steaks were displayed under simulated retail conditions at 4°C for 12days. Purge loss, pH, color stability, oxidative stability and microbial counts were monitored. Aerobically packaged steaks exhibited a bright-red color at the first 4days. However, discoloration and oxidation became major factors limiting their shelf-life to 8days. Compared with aerobic packaging, anaerobic packaging extended shelf-life of heavily marbled beef steaks, due to better color stability, together with lower oxidation and microbial populations. Among all packaging methods, CO-MAP had the best preservation for steaks, with more red color than other packaging types. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Savannah River Site Eastern Transportation Hub: A Concept For a DOE Eastern Packaging, Staging and Maintenance Center - 13143

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    England, Jeffery L.; Adams, Karen; Maxted, Maxcine

    2013-07-01

    The Department of Energy (DOE) is working to de-inventory sites and consolidate hazardous materials for processing and disposal. The DOE administers a wide range of certified shipping packages for the transport of hazardous materials to include Special Nuclear Material (SNM), radioactive materials, sealed sources and radioactive wastes. A critical element to successful and safe transportation of these materials is the availability of certified shipping packages. There are over seven thousand certified packagings (i.e., Type B/Type AF) utilized within the DOE for current missions. The synergistic effects of consolidated maintenance, refurbishment, testing, certification, and costing of these services would allow formore » efficient management of the packagings inventory and to support anticipated future in-commerce shipping needs. The Savannah River Site (SRS) receives and ships radioactive materials (including SNM) and waste on a regular basis for critical missions such as consolidated storage, stabilization, purification, or disposition using H-Canyon and HB-Line. The Savannah River National Laboratory (SRNL) has the technical capability and equipment for all aspects of packaging management. SRS has the only active material processing facility in the DOE complex and is one of the sites of choice for nuclear material consolidation. SRS is a logical location to perform maintenance and periodic testing of the DOE fleet of certified packagings. This initiative envisions a DOE Eastern Packaging Staging and Maintenance Center (PSMC) at the SRS and a western hub at the Nevada National Security Site (NNSS), an active DOE Regional Disposal Site. The PSMC's would be the first place DOE would go to meet their radioactive packaging needs and the primary locations projects would go to disposition excess packaging for beneficial reuse. These two hubs would provide the centralized management of a packaging fleet rather than the current approach to design, procure, maintain and dispose of packagings on a project-by-project basis. This initiative provides significant savings in packaging costs and acceleration of project schedules. In addition to certified packaging, the PSMC would be well suited for select designs of 7A Type A packaging and Industrial Packaging. (authors)« less

  11. Type T reference function suitability for low temperature applications

    NASA Astrophysics Data System (ADS)

    Dowell, D.

    2013-09-01

    Type T thermocouples are commonly used in industrial measurement applications due to their accuracy relative to other thermocouple types, low cost, and the ready availability of measurement equipment. Type T thermocouples are very effective when used in differential measurements, as there is no cold junction compensation necessary for the connections to the measurement equipment. Type T's published accuracy specifications result in its frequent use in low temperature applications. An examination of over 328 samples from a number of manufacturers has been completed for this investigation. Samples were compared to a Standard Platinum Resistance Thermometer (SPRT) at the LN2 boiling point along with four other standardized measurement points using a characterized ice point reference, low-thermal EMF scanner and an 8.5 digit multimeter, and the data compiled and analyzed. The test points were approximately -196 °C, -75 °C, 0 °C, +100 °C, and +200 °C. These data show an anomaly in the conformance to the reference functions where the reference functions meet at 0 °C. Additionally, in the temperature region between -100 °C to -200 °C, a positive offset of up to 5.4 °C exists between the reference function equations published in the ASTM E230-06 for the nitrogen point and the measured response of the actual wire. This paper will examine the historical and technological reasons for this anomaly in the both the ASTM and IEC reference functions. At the request of the author and the Proceedings Editor the above article has been replaced with a corrected version. The original PDF file supplied to AIP Publishing contained several figures with missing information/characters—caused by processes used to generate the PDF file. All figures were affected by this error. The article has been replaced and these figures now display correctly. The corrected article was published on 7 November 2013.

  12. 7 CFR 905.140 - Gift packages.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Gift packages. 905.140 Section 905.140 Agriculture... TANGELOS GROWN IN FLORIDA Rules and Regulations Non-Regulated Fruit § 905.140 Gift packages. Any handler..., ship any varieties for the following purpose and types of shipment: (a) To any person gift packages...

  13. Evaluating penetration ability of Plodia interpunctella (Hübner) (Lepidoptera: Pyralidae) larvae into multilayer polypropylene packages

    USDA-ARS?s Scientific Manuscript database

    Larvae of the Indian meal moth, Plodia interpunctella (Hübner), can invade or penetrate packaging materials and infest food products. Energy bars with three polypropylene packaging types were challenged with eggs (first instars), third, and fifth instars of P. interpunctella to determine package res...

  14. 10 CFR 71.91 - Records.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... licensed material in each package, and the total quantity of each shipment; (5) For each item of irradiated... the shipment; (7) For fissile packages and for Type B packages, any special controls exercised; (8... determinations required by § 71.87 and by the conditions of the package approval. (b) Each certificate holder...

  15. 10 CFR 71.91 - Records.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... licensed material in each package, and the total quantity of each shipment; (5) For each item of irradiated... the shipment; (7) For fissile packages and for Type B packages, any special controls exercised; (8... determinations required by § 71.87 and by the conditions of the package approval. (b) Each certificate holder...

  16. 10 CFR 71.91 - Records.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... licensed material in each package, and the total quantity of each shipment; (5) For each item of irradiated... the shipment; (7) For fissile packages and for Type B packages, any special controls exercised; (8... determinations required by § 71.87 and by the conditions of the package approval. (b) Each certificate holder...

  17. 10 CFR 71.91 - Records.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... licensed material in each package, and the total quantity of each shipment; (5) For each item of irradiated... the shipment; (7) For fissile packages and for Type B packages, any special controls exercised; (8... determinations required by § 71.87 and by the conditions of the package approval. (b) Each certificate holder...

  18. 49 CFR 178.935 - Standards for wooden Large Packagings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... this section apply to wooden Large Packagings intended to contain solids. Wooden Large Packaging types... transportation. Where a detachable pallet is used, its top surface must be free from protrusions that might...

  19. 49 CFR 178.935 - Standards for wooden Large Packagings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... this section apply to wooden Large Packagings intended to contain solids. Wooden Large Packaging types... transportation. Where a detachable pallet is used, its top surface must be free from protrusions that might...

  20. 49 CFR 178.935 - Standards for wooden Large Packagings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... this section apply to wooden Large Packagings intended to contain solids. Wooden Large Packaging types... transportation. Where a detachable pallet is used, its top surface must be free from protrusions that might...

  1. 21 CFR 1314.110 - Reports for mail-order sales.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...

  2. 21 CFR 1314.110 - Reports for mail-order sales.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...

  3. 21 CFR 1314.110 - Reports for mail-order sales.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...

  4. 21 CFR 1314.110 - Reports for mail-order sales.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...

  5. 21 CFR 1314.110 - Reports for mail-order sales.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Administration, submit the report in electronic form, either via computer disk or direct electronic data... units (e.g., 100 doses per package); (11) Package type (blister pack, etc.); (12) Number of packages...

  6. High Temperature, Slow Strain Rate Forging of Advanced Disk Alloy ME3

    NASA Technical Reports Server (NTRS)

    Gabb, Timothy P.; OConnor, Kenneth

    2001-01-01

    The advanced disk alloy ME3 was designed in the HSR/EPM disk program to have extended durability at 1150 to 1250 F in large disks. This was achieved by designing a disk alloy and process producing balanced monotonic, cyclic, and time-dependent mechanical properties. combined with robust processing and manufacturing characteristics. The resulting baseline alloy, processing, and supersolvus heat treatment produces a uniform, relatively fine mean grain size of about ASTM 7, with as-large-as (ALA) grain size of about ASTM 3. There is a long term need for disks with higher rim temperature capabilities than 1250 F. This would allow higher compressor exit (T3) temperatures and allow the full utilization of advanced combustor and airfoil concepts under development. Several approaches are being studied that modify the processing and chemistry of ME3, to possibly improve high temperature properties. Promising approaches would be applied to subscale material, for screening the resulting mechanical properties at these high temperatures. n obvious path traditionally employed to improve the high temperature and time-dependent capabilities of disk alloys is to coarsen the grain size. A coarser grain size than ASTM 7 could potentially be achieved by varying the forging conditions and supersolvus heat treatment. The objective of this study was to perform forging and heat treatment experiments ("thermomechanical processing experiments") on small compression test specimens of the baseline ME3 composition, to identify a viable forging process allowing significantly coarser grain size targeted at ASTM 3-5, than that of the baseline, ASTM 7.

  7. Environmentally safe aviation fuels

    NASA Technical Reports Server (NTRS)

    Liberio, Patricia D.

    1995-01-01

    In response to the Air Force directive to remove Ozone Depleting Chemicals (ODC's) from military specifications and Defense Logistics Agency's Hazardous Waste Minimization Program, we are faced with how to ensure a quality aviation fuel without using such chemicals. Many of these chemicals are found throughout the fuel and fuel related military specifications and are part of test methods that help qualify the properties and quality of the fuels before they are procured. Many years ago there was a directive for military specifications to use commercially standard test methods in order to provide standard testing in private industry and government. As a result the test methods used in military specifications are governed by the American Society of Testing and Materials (ASTM). The Air Force has been very proactive in the removal or replacement of the ODC's and hazardous materials in these test methods. For example, ASTM D3703 (Standard Test Method for Peroxide Number of Aviation Turbine Fuels), requires the use of Freon 113, a known ODC. A new rapid, portable hydroperoxide test for jet fuels similar to ASTM D3703 that does not require the use of ODC's has been developed. This test has proved, in limited testing, to be a viable substitute method for ASTM D3703. The Air Force is currently conducting a round robin to allow the method to be accepted by ASTM and therefore replace the current method. This paper will describe the Air Force's initiatives to remove ODC's and hazardous materials from the fuel and fuel related military specifications that the Air Force Wright Laboratory.

  8. Effect of packaging type during postmortem aging and degree of doneness on pork chop sensory traits of loins selected to vary in color and marbling.

    PubMed

    Klehm, B J; King, D A; Dilger, A C; Shackelford, S D; Boler, D D

    2018-05-04

    The objective was to determine the interactions between packaging type and degree of doneness on sensory traits of pork loins classified based on the newly proposed USDA quality grades. A total of 144 loins were selected from 2 groups of pigs (lean growth or meat quality production focus) to represent as much variation in visual color and marbling as possible. Selection was achieved with a VQG grading camera. The ventral surface of the loins was evaluated for loin quality traits at 1 d postmortem. At 2 d postmortem loins were sliced into 28-mm-thick chops. Chop within each loin was randomly assigned to either individual vacuum packages or to individual Styrofoam trays and overwrapped in polyvinyl chloride (PVC) oxygen permeable film. Overwrapped PVC packages were then placed in bulk packages and flushed with a gas mixture that contained approximately 0.4% carbon monoxide, 30% carbon dioxide, and 80% nitrogen. Vacuum-packaged chops were aged until 14 d postmortem. Chops packaged in PVC overwrap were aged until 9 d postmortem in the bulk packages, then placed on simulated retail display until 14 d postmortem. Chops from each packaging type were cooked to an internal temperature of either 63 °C or 71 °C for the evaluation of slice shear force (SSF) or for evaluation of tenderness, juiciness, and flavor by a trained panel. Data were analyzed as split-split plot design with production focus of the pigs, proposed USDA quality grade, packaging type, and degree of doneness as fixed effects. While there were main effect differences between production focuses, there were no interactions with production focus. There were also no 3-way (P ≥ 0.19) interactions and only one 2-way interaction among quality grade, packaging type, or degree of doneness. There were no differences in sensory tenderness (P = 0.30), juiciness (P = 0.49), flavor (P = 0.89), SSF (P = 0.13), or cook loss (P = 0.06) among USDA quality grades. There were no differences in sensory tenderness (P = 0.06), juiciness (P = 0.32), flavor (P = 0.74), SSF (P = 0.99), or cook loss (P = 0.12) between chops aged in vacuum packages or PVC packages. Chops cooked to 63 °C were 4.6% more tender (P < 0.0001), 10.1% juicier (P < 0.0001), and 2.9% less flavorful (P = 0.01) than chops cooked to 71 °C. These data suggest that cooking chops to 63 °C rather than 71 °C was a more effective way to improve tenderness and juiciness than selecting chops of a certain quality grade or altering packaging postmortem.

  9. 46 CFR 160.135-5 - Incorporation by reference.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Polyester, High Strength, Flexible, (May 13, 1997), IBR approved for §§ 160.135-7 and 160.135-15. (“A-A... Specification for Carbon Structural Steel, (approved May 15, 2008), IBR approved for §§ 160.135-7 and 160.135-15 (“ASTM A 36”). (2) ASTM A 276-08a, Standard Specification for Stainless Steel Bars and Shapes, (approved...

  10. 46 CFR 160.135-5 - Incorporation by reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Polyester, High Strength, Flexible, (May 13, 1997), IBR approved for §§ 160.135-7 and 160.135-15. (“A-A... Specification for Carbon Structural Steel, (approved May 15, 2008), IBR approved for §§ 160.135-7 and 160.135-15 (“ASTM A 36”). (2) ASTM A 276-08a, Standard Specification for Stainless Steel Bars and Shapes, (approved...

  11. 46 CFR 160.135-5 - Incorporation by reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., Vinyl Nylon Or Polyester, High Strength, Flexible, (May 13, 1997), IBR approved for §§ 160.135-7 and 160... for Carbon Structural Steel, (approved May 15, 2008), IBR approved for §§ 160.135-7 and 160.135-15 (“ASTM A 36”). (2) ASTM A 276-08a, Standard Specification for Stainless Steel Bars and Shapes, (approved...

  12. Accelerated weathering of fire-retardant-treated wood for fire testing

    Treesearch

    Robert H. White

    2009-01-01

    Fire-retardant-treated products for exterior applications must be subjected to actual or accelerated weathering prior to fire testing. For fire-retardant-treated wood, the two accelerated weathering methods have been Method A and B of ASTM D 2898. The rain test is Method A of ASTM D 2898. Method B includes exposures to ultraviolet (UV) sunlamps in addition to water...

  13. 40 CFR 63.7142 - What are the requirements for claiming area source status?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

  14. 40 CFR 63.7142 - What are the requirements for claiming area source status?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

  15. 40 CFR 63.7142 - What are the requirements for claiming area source status?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

  16. 40 CFR 63.7142 - What are the requirements for claiming area source status?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

  17. 40 CFR 63.7142 - What are the requirements for claiming area source status?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... test must be repeated. (v) The post-test analyte spike procedure of section 11.2.7 of ASTM Method D6735... (3) ASTM Method D6735-01, Standard Test Method for Measurement of Gaseous Chlorides and Fluorides...)(3)(i) through (vi) of this section are followed. (i) A test must include three or more runs in which...

  18. Standard specification for anchor bolts, steel, 36, 55, and 105-ksi yield strength. ASTM standard

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    1998-07-01

    This specification is under the jurisdiction of ASTM Committee F-16 on Fasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts, Nuts, Rivets, and Washers. Current edition approved Dec. 10, 1997 and published July 1998. Originally published as F 1554-94. Last previous edition was F 1554-94.

  19. Autogenous accelerated curing of concrete cylinders. Part V, ASTM Cooperative Testing Program with additional emphasis on the influence of container and storage characteristics (supplemented by data on water bath curing from an earlier council project).

    DOT National Transportation Integrated Search

    1971-01-01

    Concomitant with the Research Council's studies of accelerated curing for strength testing, Subcommittee II-i of ASTM Committee C-9 was developing and refining accelerated methods for standardization. This development included a cooperative testing p...

  20. Ignitability analysis using the cone calorimeter and lift apparatus

    Treesearch

    Mark A. Dietenberger

    1996-01-01

    The irradiance plotted as function of time to ignition for wood materials tested in the Cone Calorimeter (ASTM E1354) differs signiticantly from that tested in the Lateral Ignition and Flame spread Test (LIFT) apparatus (ASTM E1321). This difference in piloted ignitabilty is primarily due to the difference in forced convective cooling of the specimen tested in both...

  1. AM2 Brickwork Pattern Evaluation

    DTIC Science & Technology

    2016-12-01

    pavement applications. Designation : D 6951. West Consho- hocken, PA: ASTM International. ASTM International. 2010a. Standard test method for in-place... design . This report provides test results for each evaluation and discussions comparing their perfor- mance to previous tests conducted under similar... designated by other authorized documents. DESTRUCTION NOTICE - For classified documents, follow the procedures in DOD5200.22-M, Industrial Security Manual

  2. Nondestructive testing of defective ASTM A 514 steel on the I-275 Combs-Hehl twin bridges over the Ohio River in Campbell County, Kentucky.

    DOT National Transportation Integrated Search

    2010-03-01

    Three defective ASTM A 514 steel splice plates were discovered on the I-275 Combs-Hehl twin bridges over the Ohio River. A follow-on in-depth field inspection of 1,356 A 514 steel plates on the bridges revealed 14 additional defective gusset and spli...

  3. Impact properties of zinc die cast alloys

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Schrems, Karol K.; Dogan, Omer N.; Manahan, M.P.

    2005-01-01

    Alloys 3, 5, AcuZinc 5, and ZA-8 were tested at five temperatures between -40 C and room temperature to determine impact properties. Izod impact energy data was obtained in accordance with ASTM D256. Unlike ASTM E23, these samples were tested with a milled notch in order to compare with plastic samples. In addition, flexural data was obtained for design use.

  4. 29 CFR 1910.6 - Incorporation by reference.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...); and 1910.111(d)(1) (ii) and (iii). (6) API 650 (1966) Welded Steel Tanks for Oil Storage, 3rd Ed., IBR... and Seamless Steel Pipe, IBR approved for §§ 1910.110 and 1910.111. (3) ASTM A 126-66, Gray Iron...-1968), Alloy Steel Chain, IBR approved for § 1910.184. (5) ASTM A 395-68, Ductile Iron for Use at...

  5. 29 CFR 1910.6 - Incorporation by reference.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...); and 1910.111(d)(1) (ii) and (iii). (6) API 650 (1966) Welded Steel Tanks for Oil Storage, 3rd Ed., IBR... and Seamless Steel Pipe, IBR approved for §§ 1910.110 and 1910.111. (3) ASTM A 126-66, Gray Iron...-1968), Alloy Steel Chain, IBR approved for § 1910.184. (5) ASTM A 395-68, Ductile Iron for Use at...

  6. 40 CFR Table 6 to Subpart Ddddd of... - Fuel Analysis Requirements

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., and nickel for all solid fuels) and ASTM D4606-03 (for selenium in coal) (IBR, see § 63.14(b)) or ASTM... to Subpart DDDDD of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Institutional Boilers and Process Heaters Pt. 63, Subpt. DDDDD, Table 6 Table 6 to Subpart DDDDD of Part 63—Fuel...

  7. 40 CFR Table 6 to Subpart Ddddd of... - Fuel Analysis Requirements

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., and nickel for all solid fuels) and ASTM D4606-03 (for selenium in coal) (IBR, see § 63.14(b)) or ASTM... Subpart DDDDD of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Institutional Boilers and Process Heaters Pt. 63, Subpt. DDDDD, Table 6 Table 6 to Subpart DDDDD of Part 63—Fuel...

  8. Data Processing and Measuring System for Studying the Cooling Capacity of Quenchants

    NASA Astrophysics Data System (ADS)

    Tsaplin, S. V.; Bolychev, S. A.; Shemanaev, D. V.; Mishagin, B. S.

    2014-09-01

    A domestically produced device for determining the cooling capacity of quenchants is developed on the basis of the ISO 9001, ISO 9950, ASTM D6200-01, and ASTM D6482-01 standards. Acomparison of the results of a determination of the parameters of cooling environments obtained by means of the present device and a foreign counterpart is carried out.

  9. Considerations on the ASTM standards 1789-04 and 1422-05 on the forensic examination of ink.

    PubMed

    Neumann, Cedric; Margot, Pierre

    2010-09-01

    The ASTM standards on Writing Ink Identification (ASTM 1789-04) and on Writing Ink Comparison (ASTM 1422-05) are the most up-to-date guidelines that have been published on the forensic analysis of ink. The aim of these documents is to cover most aspects of the forensic analysis of ink evidence, from the analysis of ink samples, the comparison of the analytical profile of these samples (with the aim to differentiate them or not), through to the interpretation of the result of the examination of these samples in a forensic context. Significant evolutions in the technology available to forensic scientists, in the quality assurance requirements brought onto them, and in the understanding of frameworks to interpret forensic evidence have been made in recent years. This article reviews the two standards in the light of these evolutions and proposes some practical improvements in terms of the standardization of the analyses, the comparison of ink samples, and the interpretation of ink examination. Some of these suggestions have already been included in a DHS funded project aimed at creating a digital ink library for the United States Secret Service. © 2010 American Academy of Forensic Sciences.

  10. 49 CFR 172.310 - Class 7 (radioactive) materials.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... States company or agency is the symbol “USA.” (d) Each package which conforms to a Type B(U) or Type B(M... “USA” in conjunction with the specification marking, or other package certificate identification. (See...

  11. 49 CFR 172.310 - Class 7 (radioactive) materials.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... States company or agency is the symbol “USA.” (d) Each package which conforms to a Type B(U) or Type B(M... “USA” in conjunction with the specification marking, or other package certificate identification. (See...

  12. 49 CFR 172.310 - Class 7 (radioactive) materials.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... States company or agency is the symbol “USA.” (d) Each package which conforms to a Type B(U) or Type B(M... “USA” in conjunction with the specification marking, or other package certificate identification. (See...

  13. Fretting-corrosion at the modular tapers interface: Inspection of standard ASTM F1875-98.

    PubMed

    Bingley, Rachel; Martin, Alan; Manfredi, Olivia; Nejadhamzeeigilani, Mahdiyar; Oladokun, Abimbola; Beadling, Andrew Robert; Siddiqui, Sohail; Anderson, James; Thompson, Jonathan; Neville, Anne; Bryant, Michael

    2018-05-01

    Interest in the degradation mechanisms at the modular tapers interfaces has been renewed due to increased reported cases of adverse reactions to metal debris and the appearance of wear and corrosion at the modular tapers interfaces at revision. Over the past two decades, a lot of research has been expended to understand the degradation mechanisms, with two primary implant loading procedures and orientations used consistently across the literature. ASTM F1875-98 is often used as a guide to understand and benchmark the tribocorrosion processes occurring within the modular tapers interface. This article presents a comparison of the two methods outlined in ASTM F1875-98 as well as a critique of the standard considering the current paradigm in pre-clinical assessment of modular tapers.

  14. Verification of the ASTM G-124 Purge Equation

    NASA Technical Reports Server (NTRS)

    Robbins, Katherine E.; Davis, Samuel Eddie

    2009-01-01

    ASTM G-124 seeks to evaluate combustion characteristics of metals in high-purity (greater than 99%) oxygen atmospheres. ASTM G-124 provides the following equation to determine the minimum number of purges required to reach this level of purity in a test chamber: n = -4/log10(Pa/Ph), where "n" is the total number of purge cycles required, Ph is the absolute pressure used for the purge on each cycle and Pa is the atmospheric pressure or the vent pressure. The origin of this equation is not known and has been the source of frequent questions as to its accuracy and reliability. This paper shows the derivation of the G-124 purge equation, and experimentally explores the equation to determine if it accurately predicts the number of cycles required.

  15. Effect of Shear Strain on the Structure and Properties of Chromium-Nickel Corrosion-Resistant Steels

    NASA Astrophysics Data System (ADS)

    Dobatkin, S. V.; Rybal'chenko, O. V.; Kliauga, A.; Tokar', A. A.

    2015-07-01

    The structure and properties of metastable austenitic steel 08Kh18N10T and stable austenitic steel ASTM F138 under shear deformation implemented by torsion under hydrostatic pressure (THP) at T = 300 and 450°C and by equichannel angular pressing (ECAP) at T = 400°C are studied. The THP yields an ultrafine-grain structure in a fully austenitic matrix with grain size 45 - 70 nm in steel ASTM F138 and 87 - 123 nm in steel 08Kh1810T. The ECAP at 400°C yields a grain-subgrain structure with structural elements 100 - 300 nm in size in steel 08Kh18N10T and 200 - 400 nm in size in steel ASTM F138.

  16. Assessment of tungsten/rhenium thermocouples with metal-carbon eutectic fixed points up to 1500°C

    NASA Astrophysics Data System (ADS)

    Gotoh, M.

    2013-09-01

    Four Type A thermocouples and two Type C thermocouples were calibrated at the Au fixed point and Co-C and Pd-C eutectic fixed points. The thermocouples were exposed to 1330 °C for a total of 100 hours. The maximum drift due to the exposure was found to be 4.8 °C. The fixed-point calibration EMF of these thermocouples deviated by less than 0.86% from the temperature specified by the standards ASTM E230-2003 for Type C and GOSTR 8.585-2001 for Type A. The length of one of Type A thermocouples A52 is longer than the others by 150mm. Making use of this provision it was possible to place annealed part of A52 to the temperature gradient part of calibration arrangement every time. Therefore observed aging effect was as low as 0.5 °C compared to the other thermocouples.

  17. A menagerie of promotional characters: promoting food to children through food packaging.

    PubMed

    Hebden, Lana; King, Lesley; Kelly, Bridget; Chapman, Kathy; Innes-Hughes, Christine

    2011-01-01

    To determine the extent to which (1) promotional characters are used on food packaging for healthful and less-healthful food and (2) different companies use this persuasive marketing strategy. Cross-sectional supermarket audit of all food and beverages featuring promotional characters on the packaging. Three Australian supermarket chains. Frequency of observed products, package size, nutritional composition. Frequencies and bivariate analyses was conducted. Nutritional composition (healthful vs less healthful) was analyzed by character type and company type, that is, whether the company was signed to the Australian Food and Grocery Council Responsible Marketing to Children Initiative (RMCI) signatory. Products featuring promotional characters on packaging (n = 352) were predominantly less-healthful food and beverages (70%). [corrected]. Nutritional composition varied significantly by character type, with 69% of products with sportspersons, celebrities, or movie tie-ins being healthful, compared with 38% of licensed and 16% [corrected] of company-owned characters. Only 13 of the 75 companies using characters on packaging were RMCI signatory. Promotional characters are largely used on food packaging to promote less-healthful food to children. Most of these characters are company-owned characters that are not subject to any form of regulation in Australia. Further efforts to limit this form of marketing to children are required. Copyright © 2011 Society for Nutrition Education. Published by Elsevier Inc. All rights reserved.

  18. Techniques for Reducing Thermal Contact Resistance in Steady-State Thermal Conductivity Measurements on Polymer Composites

    NASA Astrophysics Data System (ADS)

    Stacey, C.; Simpkin, A. J.; Jarrett, R. N.

    2016-11-01

    The National Physical Laboratory (NPL) has developed a new variation on the established guarded hot plate technique for steady-state measurements of thermal conductivity. This new guarded hot plate has been specifically designed for making measurements on specimens with a thickness that is practical for advanced industrial composite materials and applications. During the development of this new guarded hot plate, NPL carried out an experimental investigation into methods for minimising the thermal contact resistance between the test specimen and the plates of the apparatus. This experimental investigation included tests on different thermal interface materials for use in another NPL facility based on a commercial guarded heat flow meter apparatus conforming to standard ASTM E1530-11. The results show the effect of applying different quantities of the type of heat transfer compound suggested in ASTM E1530-11 (clause 10.7.3) and also the effect on thermal resistance of alternative types of thermal interface products. The optimum quantities of two silicone greases were determined, and a silicone grease filled with copper was found to offer the best combination of repeatability, small hysteresis effect and a low thermal contact resistance. However, two products based on a textured indium foil and pyrolytic graphite sheet were found to offer similar or better reductions in thermal contact resistance, but with quicker, easier application and the advantages of protecting the apparatus plates from damage and being useable with specimen materials that would otherwise absorb silicone grease.

  19. Suggested Courseware for the Non-Calculus Physics Student: Simple Harmonic Motion, Wave Motion, and Sound.

    ERIC Educational Resources Information Center

    Grable-Wallace, Lisa; And Others

    1989-01-01

    Evaluates 5 courseware packages covering the topics of simple harmonic motion, 7 packages for wave motion, and 10 packages for sound. Discusses the price range, sub-topics, program type, interaction, time, calculus required, graphics, and comments of each courseware. Selects several packages based on the criteria. (YP)

  20. Technical Review Report for the Mound 1KW Package Safety Analysis Report for Packaging Waiver for the Use of Modified Primary Containment Vessel (PCV)

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    West, M; Hafner, R

    2008-05-05

    This Technical Review Report (TRR) documents the review, performed by the Lawrence Livermore National Laboratory (LLNL) staff, at the request of the U.S. Department of Energy (DOE), on the Waiver for the Use of Modified Primary Containment Vessels (PCV). The waiver is to be used to support a limited number of shipments of fuel for the Multi-Mission Radioisotope Thermoelectric Generator (MMRTG) Project in support of the National Aeronautics and Space Administration's (NASA's) Mars Science Laboratory (MSL) mission. Under the waiver, an inventory of existing national security PCVs will be converted to standard PCVs. Both types of PCVs are currently approvedmore » for use by the Office of Nuclear Energy. LLNL has previously reviewed the national security PCVs under Mound 1KW Package Safety Analysis Report for Packaging, Addendum No. 1, Revision c, dated June 2007 (Addendum 1). The safety analysis of the package is documented in the Safety Analysis Report for Packaging (SARP) for the Mound 1KW Package (i.e., the Mound 1KW SARP, or the SARP) where the standard PCVs have been reviewed by LLNL. The Mound 1KW Package is certified by DOE Certificate of Compliance (CoC) number USA/9516/B(U)F-85 for the transportation of Type B quantities of plutonium heat source material. The waiver requests an exemption, claiming safety equivalent to the requirements specified in 10 CFR 71.12, Specific Exemptions, and will lead to a letter amendment to the CoC. Under the waiver, the Office of Radioisotope Power Systems, NE-34, is seeking an exemption from 10 CFR 71.19(d)(1), Previously Approved Package,[5] which states: '(d) NRC will approve modifications to the design and authorized contents of a Type B package, or a fissile material package, previously approved by NRC, provided--(1) The modifications of a Type B package are not significant with respect to the design, operating characteristics, or safe performance of the containment system, when the package is subjected to the tests specified in {section}71.71 and 71.73.' The LLNL staff had previously reviewed a request from Idaho National Laboratory (INL) to reconfigure national security PCVs to standard PCVs. With a nominal 50% reduction in both the height and the volume, the LLNL staff initially deemed the modifications to be significant, which would not be allowed under the provisions of 10 CFR 71.19(d)(1)--see above. As a follow-up, the DOE requested additional clarification from the Nuclear Regulatory Commission (NRC). The NRC concluded that the reconfiguration would be a new fabrication, and that an exemption to the regulations would be required to allow its use, as per the requirements specified in 10 CFR 71.19(c)(1), Previously Approved Package: '(c) A Type B(U) package, a Type B(M) package, or a fissile material package previously approved by the NRC with the designation '-85' in the identification number of the NRC CoC, may be used under the general license of {section}71.17 with the following additional conditions: (1) Fabrication of the package must be satisfactorily completed by December 31, 2006, as demonstrated by application of its model number in accordance with 71.85(c).' Although the preferred approach toward the resolution of this issue would be for the applicant to submit an updated SARP, the applicant has stated that the process of updating the Model Mound 1KW Package SARP is a work that is in progress, but that the updated SARP is not yet ready for submittal. The applicant has to provide a submittal, proving that the package meets the '-96' requirements of International Atomic Energy Agency (IAEA) Safety Standards Series No. TS-R-1, in order to fabricate approved packagings after December 31, 2006. The applicant has further stated that all other packaging features, as described in the currently approved Model Mound 1KW Package SARP, remain unchanged. This report documents the LLNL review of the waiver request. The specific review for each SARP Chapter is documented.« less

Some links on this page may take you to non-federal websites. Their policies may differ from this site.
Top