Sample records for paint curing oven

  1. Strength of Geopolymer Cement Curing at Ambient Temperature by Non-Oven Curing Approaches: An Overview

    NASA Astrophysics Data System (ADS)

    Wattanachai, Pitiwat; Suwan, Teewara

    2017-06-01

    At the present day, a concept of environmentally friendly construction materials has been intensively studying to reduce the amount of releasing greenhouse gases. Geopolymer is one of the cementitious binders which can be produced by utilising pozzolanic wastes (e.g. fly ash or furnace slag) and also receiving much more attention as a low-CO2 emission material. However, to achieve excellent mechanical properties, heat curing process is needed to apply to geopolymer cement in a range of temperature around 40 to 90°C. To consume less oven-curing energy and be more convenience in practical work, the study on geopolymer curing at ambient temperature (around 20 to 25°C) is therefore widely investigated. In this paper, a core review of factors and approaches for non-oven curing geopolymer has been summarised. The performance, in term of strength, of each non-oven curing method, is also presented and analysed. The main aim of this review paper is to gather the latest study of ambient temperature curing geopolymer and to enlarge a feasibility of non-oven curing geopolymer development. Also, to extend the directions of research work, some approaches or techniques can be combined or applied to the specific properties for in-field applications and embankment stabilization by using soil-cement column.

  2. Effect of hydrated lime on compressive strength mortar of fly ash laterite soil geopolymer mortar

    NASA Astrophysics Data System (ADS)

    Wangsa, F. A.; Tjaronge, M. W.; Djamaluddin, A. R.; Muhiddin, A. B.

    2017-11-01

    This paper explored the suitability of fly ash, hydrated lime, and laterite soil with several activator (sodium hydroxide and sodium tiosulfate) to produce geopolymer mortar. Furthermore, the heat that released by hydrated lime was used instead of oven curing. In order to produce geopolymer mortar without oven curing, three variations of curing condition has been applied. Based on the result, all the curing condition showed that the hardener mortar can be produced and exhibited the increasing of compressive strength of geopolymer mortar from 3 days to 7 days without oven curing.

  3. Accelerated bridge paint test program.

    DOT National Transportation Integrated Search

    2011-07-06

    The accelerated bridge paint (AB-Paint) program evaluated a new Sherwin-Williams two-coat, : fast-curing paint system. The system is comprised of an organic zinc-rich primer (SW Corothane I : Galvapac One-Pack Zinc-Rich Primer B65 G11) and a polyurea...

  4. Ultrasonic Coating and Holographic Exposure Technology. Phase 1

    DTIC Science & Technology

    2015-09-01

    introducing plaques to cure, which allowed the UV lamps to warm up. Temperature inside the UV oven could reach 35 °C if left on continuously. Curing time for...the deposition of thin films using an ultrasonic spray coater and patterning of the films using an ultraviolet ( UV ) laser. The main objectives for...required, and include such items as a corona discharge device, a UV curing oven, hot plate, and jigging for optics that were fabricated at Revision. Test

  5. 40 CFR 63.3965 - How do I determine the emission capture system efficiency?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...; coating solvent flash-off, curing, and drying occurs within the capture system; and the removal or... spray booth and a curing oven. (b) Measuring capture efficiency. If the capture system does not meet... surface preparation activities and drying and curing time. (c) Liquid-to-uncaptured-gas protocol using a...

  6. Effect of radiation light characteristics on surface hardness of paint-on resin for shade modification.

    PubMed

    Arikawa, Hiroyuki; Kanie, Takahito; Fujii, Koichi; Ban, Seiji

    2005-12-01

    The purpose of this study was to investigate the effect of radiation light characteristics--of different types of clinical light-curing unit--on polymerization efficiency, as determined by the surface hardness of light-cured paint-on resins. Four shades of paint-on resin for shade modification of restorative resins were used. Materials were cured using one laboratory and three clinical light-curing units with different light sources, namely tungsten-halogen, LED, plasma arc, and xenon flash lamps. Knoop hardness measurements were taken at both the top and bottom surfaces of the specimens to assess the mechanical properties and degree of polymerization. Both LED and plasma arc light units caused significantly poorer surface hardness than the halogen and laboratory xenon lights. In addition, the transparent shade was more sensitive to surface hardness than other chromatic shades. Our results indicated that the polymerization efficiency of paint-on resin was significantly influenced by the radiation light characteristics of clinical light-curing units.

  7. Study on compressive strength of self compacting mortar cubes under normal & electric oven curing methods

    NASA Astrophysics Data System (ADS)

    Prasanna Venkatesh, G. J.; Vivek, S. S.; Dhinakaran, G.

    2017-07-01

    In the majority of civil engineering applications, the basic building blocks were the masonry units. Those masonry units were developed as a monolithic structure by plastering process with the help of binding agents namely mud, lime, cement and their combinations. In recent advancements, the mortar study plays an important role in crack repairs, structural rehabilitation, retrofitting, pointing and plastering operations. The rheology of mortar includes flowable, passing and filling properties which were analogous with the behaviour of self compacting concrete. In self compacting (SC) mortar cubes, the cement was replaced by mineral admixtures namely silica fume (SF) from 5% to 20% (with an increment of 5%), metakaolin (MK) from 10% to 30% (with an increment of 10%) and ground granulated blast furnace slag (GGBS) from 25% to 75% (with an increment of 25%). The ratio between cement and fine aggregate was kept constant as 1: 2 for all normal and self compacting mortar mixes. The accelerated curing namely electric oven curing with the differential temperature of 128°C for the period of 4 hours was adopted. It was found that the compressive strength obtained from the normal and electric oven method of curing was higher for self compacting mortar cubes than normal mortar cube. The cement replacement by 15% SF, 20% MK and 25%GGBS obtained higher strength under both curing conditions.

  8. 40 CFR 63.1179 - For curing ovens, what standards must I meet?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... operating limits for each curing oven: (1) Maintain the free-formaldehyde content of each resin lot and the formaldehyde content of each binder formulation at or below the specification ranges of the resin and binder...

  9. 40 CFR 63.4165 - How do I determine the emission capture system efficiency?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... system; coating solvent flash-off and coating, curing, and drying occurs within the capture system and... when being moved between a spray booth and a curing oven. (b) If the capture system does not meet both... surface preparation activities and drying or curing time. (c) Liquid-to-uncaptured-gas protocol using a...

  10. 40 CFR 63.1179 - For curing ovens, what standards must I meet?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... operating limits for each curing oven: (1) Maintain the free-formaldehyde content of each resin lot and the formaldehyde content of each binder formulation at or below the specification ranges of the resin and binder...

  11. Chemical curing in alkyd paints: An evaluation via FT-IR and NMR spectroscopies

    NASA Astrophysics Data System (ADS)

    Bartolozzi, G.; Marchiafava, V.; Mirabello, V.; Peruzzini, M.; Picollo, M.

    2014-01-01

    A study aimed at determining the time necessary for an alkyd paint to attain chemical curing is presented. In particular, the object of our investigation was an oil paint made by Winsor & Newton, namely French ultramarine (PB29) in the Griffin Alkyd “fast drying oil colour” series. Using this paint, we prepared several mock-ups on glass. These were left in the laboratory at room temperature in a piece of furniture with glass doors for a total of 70 days. Samples were taken at different times, and the changes in their composition were monitored by means of FT-IR and multinuclear NMR spectroscopic analyses. Since the cross-linking reactions involved in the formation of the pictorial film mainly affect the amount of carbon-carbon double bonds, we monitored the decrease in allyl, diallyl and vinyl protons and carbons. The data obtained from the use of both techniques led us to conclude that, in our particular experimental conditions, the chemical curing of the paint layer is reached within the first 70 days, thus establishing the beginning of the ageing phenomena.

  12. Improved method facilitates debulking and curing of phenolic impregnated asbestos

    NASA Technical Reports Server (NTRS)

    Gaines, P.

    1966-01-01

    Workpieces covered with phenolic impregnated asbestos tape and then wrapped with a specified thickness of nylon yarn under pressure, are debulked and cured in a standard oven. This method of debulking and curing is used in the fabrication of ablative chambers for the Gemini and Apollo attitude control engines.

  13. Chemical curing in alkyd paints: an evaluation via FT-IR and NMR spectroscopies.

    PubMed

    Bartolozzi, G; Marchiafava, V; Mirabello, V; Peruzzini, M; Picollo, M

    2014-01-24

    A study aimed at determining the time necessary for an alkyd paint to attain chemical curing is presented. In particular, the object of our investigation was an oil paint made by Winsor & Newton, namely French ultramarine (PB29) in the Griffin Alkyd "fast drying oil colour" series. Using this paint, we prepared several mock-ups on glass. These were left in the laboratory at room temperature in a piece of furniture with glass doors for a total of 70 days. Samples were taken at different times, and the changes in their composition were monitored by means of FT-IR and multinuclear NMR spectroscopic analyses. Since the cross-linking reactions involved in the formation of the pictorial film mainly affect the amount of carbon-carbon double bonds, we monitored the decrease in allyl, diallyl and vinyl protons and carbons. The data obtained from the use of both techniques led us to conclude that, in our particular experimental conditions, the chemical curing of the paint layer is reached within the first 70 days, thus establishing the beginning of the ageing phenomena. Copyright © 2013 Elsevier B.V. All rights reserved.

  14. Effect of Molarity of Sodium Hydroxide and Curing Method on the Compressive Strength of Ternary Blend Geopolymer Concrete

    NASA Astrophysics Data System (ADS)

    Sathish Kumar, V.; Ganesan, N.; Indira, P. V.

    2017-07-01

    Concrete plays a vital role in the development of infrastructure and buildings all over the world. Geopolymer based cement-less concrete is one of the current findings in the construction industry which leads to a green environment. This research paper deals with the results of the use of Fly ash (FA), Ground Granulated Blast Furnace Slag (GGBS) and Metakaolin (MK) as a ternary blend source material in Geopolymer concrete (GPC). The aspects that govern the compressive strength of GPC like the proportion of source material, Molarity of Sodium Hydroxide (NaOH) and Curing methods were investigated. The purpose of this research is to optimise the local waste material and use them effectively as a ternary blend in GPC. Seven combinations of binder were made in this study with replacement of FA with GGBS and MK by 35%, 30%, 25%, 20%, 15%, 10%, 5% and 5%, 10%, 15%, 20%, 25%, 30%, 35% respectively. The molarity of NaOH solution was varied by 12M, 14M and 16M and two types of curing method were adopted, viz. Hot air oven curing and closed steam curing for 24 hours at 60°C (140°F). The samples were kept at ambient temperature till testing. The compressive strength was obtained after 7 days and 28 days for the GPC cubes. The test data reveals that the ternary blend GPC with molarity 14M cured by hot air oven produces the maximum compressive strength. It was also observed that the compressive strength of the oven cured GPC is approximately 10% higher than the steam cured GPC using the ternary blend.

  15. Characterization of concrete hardness by using sugarcane bagasse waste mixture by carbon oven curing process

    NASA Astrophysics Data System (ADS)

    Rino, Agus; Farida, Elvaswer, Dahlan, Dahyunir

    2017-01-01

    Sugarcane bagasse is one of the solid waste that can be processed as a mixture of structure materials. In the previous research, sugarcane bagasse has been processed and used as a mixture of portland cement, the manufacture of asbestos and also mixtures for manufacturing of brake pads that are frequently used in motor vehicle. Based on the previous research results, it is strongly necessary to develop a research about sugarcane bagasse for structure materials. The method used to determine the mechanical properties is tensile test and compression test. To obtain the intensity of material variations, it is needed to make various sizes of filtration carbon in the form of aggregate that is mixed into the tiles material. The size of the aggregate used in concrete material can be on 200 µm, 400 µm and 600 µm. This measure is taken in accordance with the size of the filtration apparatus. Furthermore, in obtaining sugarcane bagasse carbon, the researcher must do the oven curing process on 200 °C temperature and 3 hours in curing oven. In this research the best result is used bagasse powder mixtured 200 µm is 7. 2 MPa.

  16. 40 CFR 63.4964 - How do I determine the emission capture system efficiency?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... operation are applied within the capture system; coating solvent flash-off and coating, curing, and drying... parts enter the open shop environment when being moved between a spray booth and a curing oven. (b... from the beginning to the end of production, which includes surface preparation activities and drying...

  17. 2.45 GHz Microwave Processing and Its Influence on Glass Fiber Reinforced Plastics

    PubMed Central

    Zaremba, Swen

    2018-01-01

    During the production of fiber-reinforced composite materials, liquid resin is introduced into the fiber material and cured, i.e., hardened. An elevated temperature is needed for this curing. Microwave curing of composites has been investigated for some time, but it has mostly been done using small domestic or laboratory equipment. However, no investigation has been carried out using an industrial-sized chamber-microwave for glass fiber-reinforced plastic (GFRP). Here, we show that microwave curing produces laminates of the same quality as oven-cured ones. The study shows that, if the process is done right, GFRP samples can be produced with an industrial scale microwave. Even if not fully cured, microwave samples show a glass transition temperature measured with DMA (Tg-DMA) that is comparable to the Tg-DMA according to the proposed cure cycle on the data sheet. Specific microwave-cured configurations show better inter-laminar shear strength than oven specimens. The results show that microwave-based heat introduction can be a beneficial curing method for GFRP laminates. A microwave-optimized process is faster and leads to better mechanical properties. PMID:29783684

  18. 2.45 GHz Microwave Processing and Its Influence on Glass Fiber Reinforced Plastics.

    PubMed

    Teufl, Daniel; Zaremba, Swen

    2018-05-18

    During the production of fiber-reinforced composite materials, liquid resin is introduced into the fiber material and cured, i.e., hardened. An elevated temperature is needed for this curing. Microwave curing of composites has been investigated for some time, but it has mostly been done using small domestic or laboratory equipment. However, no investigation has been carried out using an industrial-sized chamber-microwave for glass fiber-reinforced plastic (GFRP). Here, we show that microwave curing produces laminates of the same quality as oven-cured ones. The study shows that, if the process is done right, GFRP samples can be produced with an industrial scale microwave. Even if not fully cured, microwave samples show a glass transition temperature measured with DMA ( T g-DMA ) that is comparable to the T g-DMA according to the proposed cure cycle on the data sheet. Specific microwave-cured configurations show better inter-laminar shear strength than oven specimens. The results show that microwave-based heat introduction can be a beneficial curing method for GFRP laminates. A microwave-optimized process is faster and leads to better mechanical properties.

  19. A Meta-Analysis Of Corrosion Studies for Maritime Patrol and Reconnaissance Aircraft (MPRA)

    DTIC Science & Technology

    2016-09-01

    performed onsite. Aircraft rating was based upon the presence and/or extent of paint adhesion, paint cracking , clean ability, fluid damage, oxidation...because of corrosion control maintenance. No significant issues were observed related to paint cracking , fluid damage, corrosion, and clean ability of...HEXAMETHYLENEDIISOCYANATE 822-06-0 83194 X-310A; POLYURETHANE CATALYST XYLENE 1330-20-7 82649 X-530; HS EPOXY ENAMEL CURING SOLUTION BUTANOL 71-36-3

  20. Adjustable-Pressure Mandrel For Making Composite Tubes

    NASA Technical Reports Server (NTRS)

    Jacoy, Paul J.; Schmitigal, Wesley P.

    1993-01-01

    Inflatable inner mandrel enables application of any desired pressure (within reasonable limits) during curing stage in fabrication of fiber/matrix composite tube. Consists mainly of sheath of silicone rubber sealed on aluminum tube. Composite material laid up on mandrel and enclosed in rigid outer die. Sheath on inner mandrel inflated to requisite pressure and regulated during curing. Assembly then placed in oven and cured at specified temperature.

  1. Applications of Blue Light-curing Acrylic Resin to Forensic Sample Preparation and Microtomy.

    PubMed

    Groves, Ethan; Palenik, Christopher S

    2016-03-01

    This study discusses the results of an evaluation of a one-part blue light-curing acrylic resin for embedding trace evidence prior to the preparation of thin sections with a microtome. Through a comparison to several epoxy resins, the physical properties relevant to both trace evidence examination and analytical microscopy in general, including as viscosity, clarity, color, hardness, and cure speed, were explored. Finally, thin sections from paint samples embedded in this acrylic resin were evaluated to determine if, through smearing or impregnation, the resin contributed to the infrared spectra. The results of this study show that blue light-curing acrylic resins provide the desired properties of an embedding medium, generate high-quality thin sections, and can significantly simplify the preparation of paint chips, fibers and a multitude of other types of microscopic samples in the forensic trace evidence laboratory. © 2015 American Academy of Forensic Sciences.

  2. Strength Performance of Blended Ash Based Geopolymer Mortar

    NASA Astrophysics Data System (ADS)

    Zahib, Zaidahtulakmal M.; Kamaruddin, Kartini; Saman, Hamidah M.

    2018-03-01

    Geopolymer is a based on inorganic alumino-silicate binder system. Geopolymeric materials are formed using materials that containing silica and aluminium such as fly ash and rice husk ash, which activated by alkaline solution. This paper presents the study on the effect of replacement of SSA in RHA based geopolymer, types of curing and different molarity of NaOH used on the strength of Sewage Sludge Ash (SSA) and Rice Husk Ash (RHA) based geopolymer mortar incorporating with three (3) different mix proportions. Based geopolymer mortar was synthesized from treated sewage sludge and rice husk undergoing incineration process in producing ashes, activated with sodium silicate and sodium hydroxide solution by ratio of 2.5:1 and solution to ash ratio of 1:1. Molarity of 8M and 10M NaOH were used. The percentages of SSA replacement were 0%, 10% and 20% by weight. Compressive strength was conducted at age 7, 14 and 28 days to see the development of strength with two curing regimes, which are air curing and oven curing (60°C for 24 hours). From the research conducted, the ultimate compressive strength (6.28MPa) was obtained at zero replacement of SSA taken at 28 days of oven curing with 10M of NaOH. This shows that RHA, which is rich in silica content is enough to enhance the strength of geopolymer mortar especially with high molarity of NaOH.

  3. 40 CFR 60.493 - Performance test and compliance provisions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Beverage Can Surface Coating Industry § 60.493 Performance test and compliance provisions. (a) Section 60.8... operation Emission distribution Coater/flashoff (Se) Curing oven (Sh) Two-piece aluminum or steel can...

  4. Properties of cold-bonded lightweight artificial aggregate containing bottom ash with different curing regime

    NASA Astrophysics Data System (ADS)

    Mohamad Ibrahim, Norlia; Nizar Ismail, Khairul; Che Amat, Roshazita; Mohamad Ghazali, Mohamad Iqbal

    2018-03-01

    Cold-bonded pelletizing technique is frequently used in aggregate manufacturing process as it can minimise the energy consumption. It has contributed to both economical and environmental advantages because it helps to reduce the gas emissions problems. Bottom ash collected from municipal solid waste incineration (MSWI) plant was selected as raw material in this study and was utilised as a partial replacement for cement for artificial aggregate production. Several percentage of ash replacement was selected ranged from 10 to 50%. Aggregate pellets were subjected to different types of curing condition which is room-water (RW), room-room (RR), oven-room (OR) and oven-water (OW) condition. Properties of aggregate pellets were examined to obtain its density, water absorption, aggregate impact value (AIV) and specific gravity (SG). The results indicated that the most efficient curing regime is by exposing the aggregate in RW condition. The optimum aggregate was selected at 20% where it has satisfied the required density of 739.5kg/m3, and classified as strong aggregate with AIV 14. However, the water absorption of aggregate increased proportionately with the increment of ash content.

  5. Microkinetic modeling of the autoxidative curing of an alkyd and oil-based paint model system

    NASA Astrophysics Data System (ADS)

    Oakley, Lindsay H.; Casadio, Francesca; Shull, Kenneth R.; Broadbelt, Linda J.

    2015-11-01

    Elucidating the curing and aging mechanisms of alkyd and other oil-based paints is valuable for the fields of conservation and bio-based coatings. Recent research has demonstrated the limitations of artificial aging in predicting the actual properties of paints that are hundreds of years old. Kinetic modeling offers pathways to develop a realistic and dynamic description of the composition of these oil-based paint coatings and facilitates the exploration of the effects of various environmental conditions on their long-term chemical stability. This work presents the construction of a kinetic Monte Carlo framework from elementary steps for the cobalt-catalyzed autoxidative curing of an ethyl linoleate model system up to the formation of single cross-links. Kinetic correlations for reaction families of similar chemistry are employed to reduce the number of parameters required to calculate rate constants in Arrhenius form. The model, developed from mechanisms proposed in the literature, shows good agreement with experiment for the formation of primary products in the early stages of curing. The model has also revealed that the mechanisms proposed in the literature for the formation of secondary products, such as volatile aldehydes, are still not well established, and alternative routes are under evaluation.

  6. Influence of Curing on the Strength Development of Calcium-Containing Geopolymer Mortar

    PubMed Central

    Li, Xueying; Wang, Zheng; Jiao, Zhenzhen

    2013-01-01

    This paper investigated the curing effects on the mechanical properties of calcium-containing geopolymer mortar. Three precursors are used: Class C fly ash, Class F fly ash plus calcium hydroxide and Class F fly ash plus slag. Curing conditions included: (1) standard curing at 20 ± 3 °C and RH 95% (C); (2) steam curing at 60 °C for 24 h (S); (3) steam curing at 60 °C for 6 h (S6); and (4) oven curing at 60 °C for 24 h (O), then the latter three followed by the standard curing. Under the standard conditions, the flexural strength and compressive strength of Class C fly ash geopolymer mortars developed quickly until the age of 7 days, followed by a gradual increase. Specimens with Class F fly ash plus Ca(OH)2 showed slow increase till the age of 28 days. Under these non-standard conditions (2–4), all specimens showed higher 3-day strength, while later strengths were either higher or lower than those in standard conditions, depending on the type of the precursor. PMID:28788377

  7. Influence of Curing on the Strength Development of Calcium-Containing Geopolymer Mortar.

    PubMed

    Li, Xueying; Wang, Zheng; Jiao, Zhenzhen

    2013-11-07

    This paper investigated the curing effects on the mechanical properties of calcium-containing geopolymer mortar. Three precursors are used: Class C fly ash, Class F fly ash plus calcium hydroxide and Class F fly ash plus slag. Curing conditions included: (1) standard curing at 20 ± 3 °C and RH 95% (C); (2) steam curing at 60 °C for 24 h (S); (3) steam curing at 60 °C for 6 h (S6); and (4) oven curing at 60 °C for 24 h (O), then the latter three followed by the standard curing. Under the standard conditions, the flexural strength and compressive strength of Class C fly ash geopolymer mortars developed quickly until the age of 7 days, followed by a gradual increase. Specimens with Class F fly ash plus Ca(OH)₂ showed slow increase till the age of 28 days. Under these non-standard conditions (2-4), all specimens showed higher 3-day strength, while later strengths were either higher or lower than those in standard conditions, depending on the type of the precursor.

  8. Solid freeform fabrication of biomaterials

    NASA Astrophysics Data System (ADS)

    Chu, Tien-Min Gabriel

    1999-12-01

    The biological performance of porous Hydroxyapatite (HA) is closely related to the pore architecture in the implants. The study on the effect of architecture to the biological performance of porous HA requires new manufacturing methods that can fabricate implants with controlled pores channels. In this thesis, four highly loaded HA and alumina suspensions were formulated and three different processes involving Solid Freeform Fabrication (SFF) were developed. An aqueous HA suspension in acrylamides was first formulated and the UV-curing properties were evaluated. With a medical grade HA powder, two non-aqueous HA suspensions were formulated: a 40 vol.% HA suspension in Hexanediol Diacrylate (HDDA) and a 40 vol.% HA suspension in 1:1 mix of Propoxylated Neopentyl Glycol Diacrylate (PNPGDA) and Isobomyl Acrylate (EBA). A 50 vol.% Alumina suspension in PNPGDA/IBA was also formulated. The effect of dispersant to the viscosity of the suspensions was characterized. In the Stereolithography (SL) method, the curing parameters of HA/HDDA and HA/PNPGDA/IBA were determined. Prototype HA implants with 1,700 mum internal channels were built directly on an SL Apparatus (SLA). The designed internal channel patterns were preserved after sintering. In the Ink-jet printing method, the high temperature flow behaviors of the suspensions were characterized. The effects of solids loading to the viscosity of the suspensions were modeled with Krieger-Dougherty equation. Leveling theory developed in paint industry was employed to analyze the self-leveling capability of the suspensions. In the indirect SL method, the thermal curing behavior of HA and alumina suspensions were characterized. The total cure time was measured and the curing kinetics was modeled. Negative molds for the implants were designed and built on SLA with epoxy resin. HA/PNPGDA/IBA was cast into the mold and cured in an oven. The binders and the epoxy mold were pyrolyzed and the green bodies sintered. Internal channels with sizes in the range of 420 to 968 gm with standard deviation less than 50 mum were successfully built. The formulation and characterization techniques developed in this thesis were useful for evaluating the suspensions for SFF process. The manufacturing process developed in this thesis have provided new methods for controlling the channel size in porous HA implants.

  9. 40 CFR 63.1196 - What definitions should I be aware of?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... form mineral wool. Curing oven means a chamber in which heat is used to thermoset a binder on the... slag. It may be used as a thermal or acoustical insulation material or in the making of other products...

  10. 40 CFR 63.1196 - What definitions should I be aware of?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... form mineral wool. Curing oven means a chamber in which heat is used to thermoset a binder on the... slag. It may be used as a thermal or acoustical insulation material or in the making of other products...

  11. 40 CFR 63.1196 - What definitions should I be aware of?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... form mineral wool. Curing oven means a chamber in which heat is used to thermoset a binder on the... slag. It may be used as a thermal or acoustical insulation material or in the making of other products...

  12. Method for applying photographic resists to otherwise incompatible substrates

    NASA Technical Reports Server (NTRS)

    Fuhr, W. (Inventor)

    1981-01-01

    A method for applying photographic resists to otherwise incompatible substrates, such as a baking enamel paint surface, is described wherein the uncured enamel paint surface is coated with a non-curing lacquer which is, in turn, coated with a partially cured lacquer. The non-curing lacquer adheres to the enamel and a photo resist material satisfactorily adheres to the partially cured lacquer. Once normal photo etching techniques are employed the lacquer coats can be easily removed from the enamel leaving the photo etched image. In the case of edge lighted instrument panels, a coat of uncured enamel is placed over the cured enamel followed by the lacquer coats and the photo resists which is exposed and developed. Once the etched uncured enamel is cured, the lacquer coats are removed leaving an etched panel.

  13. 40 CFR 60.461 - Definitions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... coil. Coating application station means that portion of the metal coil surface coating operation where.... Finish coat operation means the coating application station, curing oven, and quench station used to... operation means the application system used to apply an organic coating to the surface of any continuous...

  14. A Durable Airfield Marking System.

    DTIC Science & Technology

    1985-06-01

    Resin is Mixed with the Black Curing Agent to Form the Epoxy Adhesive ..... ........... 17 14 The Gray Adhesive (White Resin Mixed with Black Curing...rubber 100 0 Polyester (peroxide-catalyzed) 100 0 Urethane 100 0 Epoxy polyamide 100 0 Acrylic latex (TT-P-1952) 100 0 Thermoplastic Tapes Type 1 100 0...suzmarrizes cost data co1parisons for traffic marking tapes, CAS tiles, fluorocarbon composites (Teflon ),and acrylic latex paint TT-P-1952. 8 -p °’. TABLE 2

  15. Instrumental physical analysis of microwaved glycerol citrate foams

    USDA-ARS?s Scientific Manuscript database

    Solid polyester glyceride polymers generated by microwave cooking were further cured in a conventional oven at 100 oC for 0, 6, 24, 48, or 72 hr and their physical properties were tested. Curing polyester glycerides resulted in decreased moisture content (MC), altered color, increased hydrated polym...

  16. Fiber-Reinforced Epoxy Composites and Methods of Making Same Without the Use of Oven or Autoclave

    NASA Technical Reports Server (NTRS)

    Barnell, Thomas J. (Inventor); Rauscher, Michael D. (Inventor); Stienecker, Rick D. (Inventor); Nickerson, David M. (Inventor); Tong, Tat H. (Inventor)

    2016-01-01

    Method embodiments for producing a fiber-reinforced epoxy composite comprise providing a mold defining a shape for a composite, applying a fiber reinforcement over the mold, covering the mold and fiber reinforcement thereon in a vacuum enclosure, performing a vacuum on the vacuum enclosure to produce a pressure gradient, insulating at least a portion of the vacuum enclosure with thermal insulation, infusing the fiber reinforcement with a reactive mixture of uncured epoxy resin and curing agent under vacuum conditions, wherein the reactive mixture of uncured epoxy resin and curing agent generates exothermic heat, and producing the fiber-reinforced epoxy composite having a glass transition temperature of at least about 100.degree. C. by curing the fiber reinforcement infused with the reactive mixture of uncured epoxy resin and curing agent by utilizing the exothermically generated heat, wherein the curing is conducted inside the thermally insulated vacuum enclosure without utilization of an external heat source or an external radiation source.

  17. Curing Effects on Interfacial Adhesion between Recycled Carbon Fiber and Epoxy Resin Heated by Microwave Irradiation

    PubMed Central

    Shimamoto, Daisuke; Hotta, Yuji

    2018-01-01

    The interfacial adhesion of recycled carbon fiber (CF) reinforced epoxy composite heated by microwave (MW) irradiation were investigated by changing the curing state of the epoxy resin. The recycled CF was recovered from the composite, which was prepared by vacuum-assisted resin transfer molding, by thermal degradation at 500 or 600 °C. Thermogravimetric analysis showed that the heating at 600 °C caused rough damage to the CF surface, whereas recycled CF recovered at 500 °C have few defects. The interfacial shear strength (IFSS) between recycled CF and epoxy resin was measured by a single-fiber fragmentation test. The test specimen was heated by MW after mixing the epoxy resin with a curing agent or pre-curing, in order to investigate the curing effects on the matrix resin. The IFSSs of the MW-irradiated samples were significantly varied by the curing state of the epoxy resin and the surface condition of recycled CF, resulting that they were 99.5 to 131.7% of oven heated samples Furthermore, rheological measurements showed that the viscosity and shrinking behaviors of epoxy resin were affected based on the curing state of epoxy resin before MW irradiation. PMID:29587422

  18. Curing Effects on Interfacial Adhesion between Recycled Carbon Fiber and Epoxy Resin Heated by Microwave Irradiation.

    PubMed

    Tominaga, Yuichi; Shimamoto, Daisuke; Hotta, Yuji

    2018-03-26

    The interfacial adhesion of recycled carbon fiber (CF) reinforced epoxy composite heated by microwave (MW) irradiation were investigated by changing the curing state of the epoxy resin. The recycled CF was recovered from the composite, which was prepared by vacuum-assisted resin transfer molding, by thermal degradation at 500 or 600 °C. Thermogravimetric analysis showed that the heating at 600 °C caused rough damage to the CF surface, whereas recycled CF recovered at 500 °C have few defects. The interfacial shear strength (IFSS) between recycled CF and epoxy resin was measured by a single-fiber fragmentation test. The test specimen was heated by MW after mixing the epoxy resin with a curing agent or pre-curing, in order to investigate the curing effects on the matrix resin. The IFSSs of the MW-irradiated samples were significantly varied by the curing state of the epoxy resin and the surface condition of recycled CF, resulting that they were 99.5 to 131.7% of oven heated samples Furthermore, rheological measurements showed that the viscosity and shrinking behaviors of epoxy resin were affected based on the curing state of epoxy resin before MW irradiation.

  19. Determination of Significant Composite Processing Factors by Designed Experiment (MSFC Center Director's Discretionary Fund)

    NASA Technical Reports Server (NTRS)

    Finckenor, J. L.

    2003-01-01

    To determie composite material properties' effects from porcessing variables, a 3 factorial designed experiment with two replicates was conducted. The factors were cure method (oven versus autoclave), layup (hand versus tape-laying machine), and thickness (8 versus 52 ply). Four material systems were tested: AS4/3501-6, IM7/8551-7, IM7/F655 bismaleimide (BMI), and shear tests on IM7/F584. Material properties were G(sub 12), v(sub 12), E(sub 1c) and E(sub 2c). Since the samples were necessarily nonstandard, strengths, though recorded, cannot be considered valid. Void content was also compared. Autoclave curing helped material properties for the low modulus fiber material but showed little benefit for higher stiffness fibers. The number of plies was very important for epoxy composites but not for the BMI. E(sub 1) was generally unaffected by any factor. Particularly high void content did correlate to reduced properties. Autoclave curing reduced void content over oven curiing but a moderate amount of voids, less than 1 percent void content, didnot correlate with material properties. Oven cures and hand layups can produce high-quality parts. Part thickness of epoxy composites is important, though cure optimization may improve performance. Significant variations can be caused by processing and it is important that test coupons always reflect the layup and processes of the final part.

  20. Comparative static curing versus dynamic curing on tablet coating structures.

    PubMed

    Gendre, Claire; Genty, Muriel; Fayard, Barbara; Tfayli, Ali; Boiret, Mathieu; Lecoq, Olivier; Baron, Michel; Chaminade, Pierre; Péan, Jean Manuel

    2013-09-10

    Curing is generally required to stabilize film coating from aqueous polymer dispersion. This post-coating drying step is traditionally carried out in static conditions, requiring the transfer of solid dosage forms to an oven. But, curing operation performed directly inside the coating equipment stands for an attractive industrial application. Recently, the use of various advanced physico-chemical characterization techniques i.e., X-ray micro-computed tomography, vibrational spectroscopies (near infrared and Raman) and X-ray microdiffraction, allowed new insights into the film-coating structures of dynamically cured tablets. Dynamic curing end-point was efficiently determined after 4h. The aim of the present work was to elucidate the influence of curing conditions on film-coating structures. Results demonstrated that 24h of static curing and 4h of dynamic curing, both performed at 60°C and ambient relative humidity, led to similar coating layers in terms of drug release properties, porosity, water content, structural rearrangement of polymer chains and crystalline distribution. Furthermore, X-ray microdiffraction measurements pointed out different crystalline coating compositions depending on sample storage time. An aging mechanism might have occur during storage, resulting in the crystallization and the upward migration of cetyl alcohol, coupled to the downward migration of crystalline sodium lauryl sulfate within the coating layer. Interestingly, this new study clearly provided further knowledge into film-coating structures after a curing step and confirmed that curing operation could be performed in dynamic conditions. Copyright © 2013 Elsevier B.V. All rights reserved.

  1. Differential Curing In Fiber/Resin Laminates

    NASA Technical Reports Server (NTRS)

    Webster, Charles N.

    1989-01-01

    Modified layup schedule counteracts tendency toward delamination. Improved manufacturing process resembles conventional process, except prepregs partially cured laid on mold in sequence in degree of partial cure decreases from mold side to bag side. Degree of partial cure of each layer at time of layup selected by controlling storage and partial-curing temperatures of prepreg according to Arrhenius equation for rate of gel of resin as function of temperature and time from moment of mixing. Differential advancement of cure in layers made large enough to offset effect of advance bag-side heating in oven or autoclave. Technique helps prevent entrapment of volatile materials during manufacturing of fiber/resin laminates.

  2. Fast-Curing Epoxy and Acrylate Adhesive Development for Adverse Marine Conditions

    DTIC Science & Technology

    2013-07-01

    the bulk properties of the adhesive. Water contact can reduce the glass transition temperature, induce cracks , or initiate hydrolysis in which the...were the same as above except they were painted with gloss black enamel paint and allowed to dry 24 h prior to application of any adhesives

  3. An ecotoxicological study on tin- and bismuth-catalysed PDMS based coatings containing a surface-active polymer.

    PubMed

    Pretti, Carlo; Oliva, Matteo; Mennillo, Elvira; Barbaglia, Martina; Funel, Marco; Reddy Yasani, Bhaskar; Martinelli, Elisa; Galli, Giancarlo

    2013-12-01

    Novel films were prepared by condensation curing reaction of a poly(dimethyl siloxane) (PDMS) matrix with bismuth neodecanoate and dibutyltin diacetate catalysts. An ecotoxicological study was performed on the leachates of the coatings using the bacterium Vibrio fischeri, the unicellular alga Dunaliella tertiolecta, the crustacean Artemia salina and the fish Sparus aurata (larvae) as testing organisms. A copper-based self-polishing commercial paint was also tested as reference. The results showed that the tin-catalysed coatings and the copper paint were highly toxic against at least two of the four test organisms, whereas bismuth-catalysed coatings did not show any toxic effect. Moreover, the same biological assessment was also carried out on PDMS coatings containing a surface-active fluorinated polymer. The toxicity of the entire polymeric system resulted only from the tin catalyst used for the condensation curing reaction, as the bismuth catalysed coatings incorporating the surface-active polymer remained atoxic toward all the tested organisms. © 2013 Elsevier Inc. All rights reserved.

  4. The Effect of Curing Temperature on the Fracture Toughness of Fiberglass Epoxy Composites

    NASA Astrophysics Data System (ADS)

    Ryan, Thomas J.

    The curing reaction in a thermoset polymer matrix composite is often accelerated by the addition of heat in an oven or autoclave. The heat added increases the rate of the polymerization reaction and cross-linking in the material. The cure cycle used (temperature, pressure and time) can therefore alter the final material properties. This research focuses on how the curing temperature (250, 275, 300 °F) affects the yield strength and the mode I interlaminar fracture toughness, GI, of a unidirectional S-2 glass epoxy composite. The test method that was used for the tension test was ASTM D3039 and the test method for the mode I interlaminar fracture toughness, the double cantilever beam (DCB) test, was ASTM D5528. The DCB specimens were fabricated with a non-adhesive insert at the midplane of the composite that serves as the initiatior of the delamination. Opening forces were then applied to the specimen, causing the crack propagation. The results show that increasing the cure temperature by 50 °F increased the tensile strength by 10% (86.54 - 94.73 ksi) and decreased the fracture toughness 20% (506.23 - 381.31 J/m 2). Thus, the curing temperature can cause a trade-off between these two properties, which means that the curing cycle will need to be altered based on the intended use and the required material properties.

  5. Solvent vapor collector

    DOEpatents

    Ellison, Kenneth; Whike, Alan S.

    1979-01-30

    A solvent vapor collector is mounted on the upstream inlet end of an oven having a gas-circulating means and intended for curing a coating applied to a strip sheet metal at a coating station. The strip sheet metal may be hot and solvent vapors are evaporated at the coating station and from the strip as it passes from the coating station to the oven. Upper and lower plenums within a housing of the collector are supplied with oven gases or air from the gas-circulating means and such gases or air are discharged within the collector obliquely in a downstream direction against the strip passing through that collector to establish downstream gas flows along the top and under surfaces of the strip so as, in turn, to induct solvent vapors into the collector at the coating station. A telescopic multi-piece shroud is usefully provided on the housing for movement between an extended position in which it overlies the coating station to collect solvent vapors released thereat and a retracted position permitting ready cleaning and adjustment of that coating station.

  6. An Information Framework for Facility Operators

    DTIC Science & Technology

    1991-01-01

    and replacement products. Type: Type is used to decompose the building into smaller categories called arrangements, assemblies, parts, joints , and forro...are organized into crews and shops consisting of tradepersons responsible for building materials (concrete, masonry, metals, drywall , paint, etc...Comp Type (pre-cast, CIP) AS I Curing compound , sealant tyDe A S 04--- Masonry Comp Type (CMU, stone, glazed) A S I Manufacturer, style no., color no

  7. A Systems Approach to Depaint Chemistry

    DTIC Science & Technology

    2009-02-01

    continuous colored film by curing through solvent evaporation, oxidation, catylization or other means. – Vehicle: Film former, binder, resin or polymer...impart large changes in properties. – Suspending agents – Driers – Anti-Skinning Agents – Wetting Agents – Anti- Foaming Agents – Coalescing Agents ...volatile stripper inside the coating. Paint Release Agent Coating Removal Mechanism Zone1: PRA Layer Zone2: PRA Initial Permeation into coating system Epoxy

  8. Processing and Dynamic Failure Characterization of Novel Impact Absorbing Transparent Interpenetrating Polymer Networks (t-IPN)

    DTIC Science & Technology

    2013-07-05

    oven for the same curing treatment as before. The scanning electron microscope (SEM) photo in Figure 19 shows a typical sample with TMSPM and IPTES...Methacrylate-based Polymers,’ S. A . Bird , PhD Dissertation, Department of Polymer and Fiber Engineering, Auburn University, Summer 2013. ’Fracture Behavior...Polymer Networks with Polyurethane-poly(methyl methacrylate),’ K. C. Jajam, S. A . Bird , M. L. Auad, and H. V. Tippur, Polymer Testing, Vol. 32, pp

  9. Processing and Dynamic Failure Characterization of Novel Impact Absorbing Transparent Interpenetrating Polymer Networks (t-IPN)

    DTIC Science & Technology

    2014-02-01

    samples were placed into the oven for the same curing treatment as before. The scanning electron microscope (SEM) photo in Figure 19 shows a typical...Interpenetrating Polymer Networks with Polyurethane and Methacrylate-based Polymers,’ S. A . Bird , PhD Dissertation, Department of Polymer and Fiber Engineering...Jajam, H. V. Tippur, S. A . Bird , and M. L. Auad, Proceedings of the 50th SES Annual Technical Meeting and ASME-AMD Summer Meeting, Providence, RI

  10. Microwave-Assisted Curing of Silicon Carbide-Reinforced Epoxy Composites: Role of Dielectric Properties

    NASA Astrophysics Data System (ADS)

    Pal, Ranu; Akhtar, M. J.; Kar, Kamal K.

    2018-05-01

    In this work, the dielectric properties of epoxy-based composites are significantly improved with the help of the silicon carbide (SiC) filler at an operating frequency of 2.45 GHz to make them ideal candidates for microwave curing. The improvement is due to enhancement of the interfacial polarization because of the presence of the SiC filler. The dielectric properties are measured using the microwave cavity perturbation method. The cavity structure is simulated using the COMSOL@Multiphysics software to verify the measured data in terms of the resonant frequency. Finally, all the SiC-based composites including the neat epoxy resin are heated in the 2.45 GHz microwave oven at 300 W for 20 min. The thermal and mechanical properties of all the cured composites are measured, and the data are compared with their room temperature pre-cured counterparts. The dielectric properties of composite samples using SiC as a reinforcing agent in the epoxy are found to be substantially improved compared with those of the pure epoxy sample, which actually leads to better curing of these composite using the 2.45 GHz microwave system.

  11. Adhesive bonded structural repair. II - Surface preparation procedures, tools, equipment and facilities

    NASA Astrophysics Data System (ADS)

    Wegman, Raymond F.; Tullos, Thomas R.

    1993-10-01

    A development status report is presented on the surface preparation procedures, tools, equipment, and facilities used in adhesively-bonded repair of aerospace and similar high-performance structures. These methods extend to both metallic and polymeric surfaces. Attention is given to the phos-anodize containment system, paint removal processes, tools for cutting composite prepreg and fabric materials, autoclaves, curing ovens, vacuum bagging, and controlled atmospheres.

  12. Rapid energy-efficient manufacturing of polymers and composites via frontal polymerization.

    PubMed

    Robertson, Ian D; Yourdkhani, Mostafa; Centellas, Polette J; Aw, Jia En; Ivanoff, Douglas G; Goli, Elyas; Lloyd, Evan M; Dean, Leon M; Sottos, Nancy R; Geubelle, Philippe H; Moore, Jeffrey S; White, Scott R

    2018-05-01

    Thermoset polymers and composite materials are integral to today's aerospace, automotive, marine and energy industries and will be vital to the next generation of lightweight, energy-efficient structures in these enterprises, owing to their excellent specific stiffness and strength, thermal stability and chemical resistance 1-5 . The manufacture of high-performance thermoset components requires the monomer to be cured at high temperatures (around 180 °C) for several hours, under a combined external pressure and internal vacuum 6 . Curing is generally accomplished using large autoclaves or ovens that scale in size with the component. Hence this traditional curing approach is slow, requires a large amount of energy and involves substantial capital investment 6,7 . Frontal polymerization is a promising alternative curing strategy, in which a self-propagating exothermic reaction wave transforms liquid monomers to fully cured polymers. We report here the frontal polymerization of a high-performance thermoset polymer that allows the rapid fabrication of parts with microscale features, three-dimensional printed structures and carbon-fibre-reinforced polymer composites. Precise control of the polymerization kinetics at both ambient and elevated temperatures allows stable monomer solutions to transform into fully cured polymers within seconds, reducing energy requirements and cure times by several orders of magnitude compared with conventional oven or autoclave curing approaches. The resulting polymer and composite parts possess similar mechanical properties to those cured conventionally. This curing strategy greatly improves the efficiency of manufacturing of high-performance polymers and composites, and is widely applicable to many industries.

  13. Evaluation of some properties of two fiber-reinforced composite materials.

    PubMed

    Lassila, Lippo V J; Tezvergil, Arzu; Lahdenperä, Milla; Alander, Pasi; Shinya, Akiyoshi; Shinya, Akikazu; Vallittu, Pekka K

    2005-08-01

    Water sorption, flexural properties, bonding properties, and elemental composition of photopolymerizable resin-impregnated fiber-reinforced composite (FRC) materials (everStick C&B and BR-100) (FPD) were evaluated in this study. Bar-shaped specimens (2 x 2 x 25 mm) were prepared for water sorption and flexural strength testing. The specimens (n = 6) were polymerized either with a hand light-curing unit for 40 s or, additionally, in a light-curing oven for 20 min and stored in water for 30 days. Water sorption was measured during this time, followed by measurements of flexural strength and modulus. A shear bond strength test was performed to determine the bonding characteristics of polymerized FRC to composite resin luting cement (Panavia-F), (n = 15). The cement was bonded to the FRC substrate and the specimens were thermocycled 5000 times (5-55 degrees C) in water. SEM/EDS were analyzed to evaluate the elemental composition of the glass fibers and the fiber distribution in cross section. ANOVA showed significant differences in water sorption according to brand (p < 0.05). Water sorption of everStick C&B was 1.86 wt% (hand-unit polymerized) and 1.94 wt% (oven polymerized), whereas BR-100 was 1.07 wt% and 1.17 wt%, respectively. The flexural strength of everStick C&B after 30 days' water storage was 559 MPa (hand-unit polymerized) and 796 MPa (oven-polymerized); for BR-100, the values were 547 MPa and 689 MPa, respectively. Mean shear bond strength of composite resin cement to the FRC varied between 20.1 and 23.7 MPa, showing no statistical difference between the materials. SEM/EDS analysis revealed that fibers of both FRC materials consist of the same oxides (SiO2, CaO, and Al2O3) in ratios. The distribution of fibers in the cross section of specimens was more evenly distributed in everStick C&B than in BR-100. The results of this study suggest that there are some differences in the tested properties of the FRC materials.

  14. Creep of experimental short fiber-reinforced composite resin.

    PubMed

    Garoushi, Sufyan; Kaleem, Muhammad; Shinya, Akikazu; Vallittu, Pekka K; Satterthwaite, Julian D; Watts, David C; Lassila, Lippo V J

    2012-01-01

    The purpose of this study was to investigate the reinforcing effect of short E-glass fiber fillers oriented in different directions on composite resin under static and dynamic loading. Experimental short fiber-reinforced composite resin (FC) was prepared by mixing 22.5 wt% of short E-glass fibers, 22.5 wt% of resin, and 55 wt% of silane-treated silica fillers. Three groups of specimens (n=5) were tested: FC with isotropic fiber orientation, FC with anisotropic fiber orientation, and particulate-filled composite resin (PFC) as a control. Time-dependent creep and recovery were recorded. ANOVA revealed that after secondary curing in a vacuum oven and after storage in dry condition for 30 days, FC with isotropic fiber orientation (1.73%) exhibited significantly lower static creep value (p<0.05) than PFC (2.54%). For the different curing methods and storage conditions evaluated in this study, FC achieved acceptable static and dynamic creep values when compared to PFC.

  15. Effect of basaltic pumice aggregate addition on the material properties of fly ash based lightweight geopolymer concrete

    NASA Astrophysics Data System (ADS)

    Top, Soner; Vapur, Hüseyin

    2018-07-01

    In this study, fly ash (FA) based geopolymer (GP) concretes were produced by using a mixture of basaltic pumice (BP) aggregates and a fly ash (Class F) for lightweight concrete production. ANOVA Yates' test technique was applied to find out the effective curing parameters. BP aggregates were ground four different fractions of particle sizes as -12 + 4 mm, -4+0.425 mm, -0.425 + 0 mm and the one containing the size distribution of Turkish Standard 802. Also, effects of the curing time in the oven were investigated. The uniaxial compressive strength (UCS) (20-55 MPa), the point load strength (4-14 kN), the water absorption (1.05%-17%), the Mohs hardness (5.5-3) and the sonic speed values (4.12-2.72 km/sn) were measured. Stress-strain curves were graphed. The density of the concrete ranged from 1700 kg/m3 to 1792 kg/m3 which confirm the lightweight concretes.

  16. Material Property Characterization of AS4/VRM-34 Textile Laminates

    NASA Technical Reports Server (NTRS)

    Grenoble, Ray W.; Johnston, William M

    2013-01-01

    Several material properties (modulus, strengths, and fracture toughness) of a textile composite have been evaluated to provide input data to analytical models of Pultruded Rod Stiffened Efficient Unitized Structure (PRSEUS). The material system is based on warp-knitted preforms of AS4 carbon fibers and VRM-34 epoxy resin, which have been processed via resin infusion and oven curing. Tensile, compressive, shear, and fracture toughness properties have been measured at ambient and elevated temperatures. All specimens were tested in as-fabricated (dry) condition. Specimens were tested with and without through-thickness stitching.

  17. Novel application of liquid chromatography/mass spectrometry for the characterization of drying oils in art: Elucidation on the composition of original paint materials used by Edvard Munch (1863-1944).

    PubMed

    La Nasa, Jacopo; Zanaboni, Marco; Uldanck, Daniele; Degano, Ilaria; Modugno, Francesca; Kutzke, Hartmut; Tveit, Eva Storevik; Topalova-Casadiego, Biljana; Colombini, Maria Perla

    2015-10-08

    Modern oil paints, introduced at the beginning of the 20th century, differ from those classically used in antiquity in their chemical and compositional features. The main ingredients were still traditional drying oils, often used in mixtures with less expensive oils and added with several classes of additives. Consequently, detailed lipid profiling, together with the study of lipid degradation processes, is essential for the knowledge and the conservation of paint materials used in modern and contemporary art. A multi-analytical approach based on mass spectrometry was used for the study of original paint materials from Munch's atelier, owned by the Munch Museum in Oslo. The results obtained in the analysis of paint tubes were compared with those obtained by characterizing a paint sample collected from one of the artist's sketches for the decoration of the Festival Hall of the University of Oslo (1909-1916). Py-GC/MS was used as screening method to evaluate the presence of lipid, proteic or polysaccaridic materials. GC/MS after hydrolysis and derivatization allowed us to determine the fatty acid profile of the paint tubes, and to evaluate the molecular changes associated to curing and ageing. The determination of the fatty acid profile is not conclusive for the characterization of complex mixtures of lipid materials, thus the characterization of the triglyceride profiles was performed using an analytical procedure based on HPLC-ESI-Q-ToF. This paper describes the first application of HPLC-ESI-Q-ToF for the acquisition of the triglyceride profile in a modern paint sample, showing the potentialities of liquid chromatography in the field of lipid characterization in modern paint materials. Moreover, our results highlighted that the application of this approach can contribute to address dating, authenticity and conservation issues relative to modern and contemporary artworks. Copyright © 2015. Published by Elsevier B.V.

  18. Effect of monomer composition of polymer matrix on flexural properties of glass fibre-reinforced orthodontic archwire.

    PubMed

    Ohtonen, J; Vallittu, P K; Lassila, L V J

    2013-02-01

    To compare force levels obtained from glass fibre-reinforced composite (FRC) archwires. Specifically, FRC wires were compared with polymer matrices having different dimethacrylate monomer compositions. FRC material (E-glass provided by Stick Tech Ltd, Turku, Finland) with continuous unidirectional glass fibres and four different types of dimethacrylate monomer compositions for the resin matrix were tested. Cross-sectionally round FRC archwires fitting into the 0.3 mm slot of a bracket were divided into 16 groups with six specimens in each group. Glass fibres were impregnated by the manufacturer, and they were initially light-cured by hand light-curing unit or additionally post-cured in light-curing oven. The FRC archwire specimens were tested at 37°C according to a three-point bending test in dry and wet conditions using a span length of 10 mm and a crosshead speed of 1.0 mm/minute. The wires were loaded until final failure. The data were statistically analysed using analysis of variance (ANOVA). The dry FRC archwire specimens revealed higher load values than water stored ones, regardless of the polymer matrix. A majority of the FRC archwires showed higher load values after being post-cured. ANOVA revealed that the polymer matrix, curing method, and water storage had a significant effect (P < 0.05) on the flexural behaviour of the FRC archwire. Polymer matrix composition, curing method, and water storage affected the flexural properties and thus, force level and working range which could be obtained from the FRC archwire.

  19. Mechanical properties of geopolymer lightweight brick with styrofoam pellet

    NASA Astrophysics Data System (ADS)

    Abdullah, Mohd Mustafa Al Bakri; Tahir, Muhammad Faheem Mohd; Kadir, Aeslina Abdul; Hussin, Kamarudin; Samson, W. Saiful Iskandar W.

    2017-09-01

    The utilization of fly ash in brick as partial replacement of cement is gaining immense importance today, mainly on account of the improvement in the long-term durability of brick combined with ecological benefits. In this research, the lightweight brick was produced by using fly ash (class F) as a main material to replace Ordinary Portland Cement (OPC) in the composition of brick. Class F Fly Ash was mixed with an alkaline activator solution (a mixture of sodium silicate and NaOH), and styrofoam pellet was added to the geopolymer mixture to produce lightweight brick. The brick was prepared in two methods that is wet method and dry method due to different brick composition which is dry method for composition with sand and wet method for composition without sand. The bricks were cured in room temperature at 7 aging days. After 7 days, the compressive strength, water absorption, and density of the brick were investigated, where the optimum ratio for the best bricks has been determined from the lightweight density and has compressive strength more than minimum standard requirement. The best bricks are further produce for curing at 60°C in oven at 28 aging days. Those bricks also were characterized using optical microscope to measure the distribution of styrofoam in brick structure. From the result obtained, the brick that cured at 60°C in oven at 28 aging days has high strength compare to brick that cured in room temperature and at 7 day cured. The water absorption is decreasing as the curing temperature and aging days increased whereas density is increasing.

  20. Optimising Ambient Setting Bayer Derived Fly Ash Geopolymers

    PubMed Central

    Jamieson, Evan; Kealley, Catherine S.; van Riessen, Arie; Hart, Robert D.

    2016-01-01

    The Bayer process utilises high concentrations of caustic and elevated temperature to liberate alumina from bauxite, for the production of aluminium and other chemicals. Within Australia, this process results in 40 million tonnes of mineral residues (Red mud) each year. Over the same period, the energy production sector will produce 14 million tonnes of coal combustion products (Fly ash). Both industrial residues require impoundment storage, yet combining some of these components can produce geopolymers, an alternative to cement. Geopolymers derived from Bayer liquor and fly ash have been made successfully with a compressive strength in excess of 40 MPa after oven curing. However, any product from these industries would require large volume applications with robust operational conditions to maximise utilisation. To facilitate potential unconfined large-scale production, Bayer derived fly ash geopolymers have been optimised to achieve ambient curing. Fly ash from two different power stations have been successfully trialled showing the versatility of the Bayer liquor-ash combination for making geopolymers. PMID:28773513

  1. Lightweight Forms for Epoxy/Aramid Ducts

    NASA Technical Reports Server (NTRS)

    Mix, E. W.; Anderson, A. N.; Bedford, Donald L., Sr.

    1986-01-01

    Aluminum mandrels easy to remove. Lightweight aluminum mandrel for shaping epoxy/aramid ducts simplifies and speeds production. In new process, glass-reinforced epoxy/aramid cloth wrapped on aluminum mandrel. Stainless-steel flanges and other hardware fitted on duct and held by simple tooling. Entire assembly placed in oven to cure epoxy. After curing, assembly placed in alkaline bath dissolves aluminum mandrel in about 4 hours. Epoxy/aramid shell ready for use as duct. Aluminum mandrel used to make ducts of various inside diameters up to 6 in. Standard aluminum forms used. Conventional tube-bending equipment produces requisite curves in mandrels.

  2. Optimising Ambient Setting Bayer Derived Fly Ash Geopolymers.

    PubMed

    Jamieson, Evan; Kealley, Catherine S; van Riessen, Arie; Hart, Robert D

    2016-05-19

    The Bayer process utilises high concentrations of caustic and elevated temperature to liberate alumina from bauxite, for the production of aluminium and other chemicals. Within Australia, this process results in 40 million tonnes of mineral residues (Red mud) each year. Over the same period, the energy production sector will produce 14 million tonnes of coal combustion products (Fly ash). Both industrial residues require impoundment storage, yet combining some of these components can produce geopolymers, an alternative to cement. Geopolymers derived from Bayer liquor and fly ash have been made successfully with a compressive strength in excess of 40 MPa after oven curing. However, any product from these industries would require large volume applications with robust operational conditions to maximise utilisation. To facilitate potential unconfined large-scale production, Bayer derived fly ash geopolymers have been optimised to achieve ambient curing. Fly ash from two different power stations have been successfully trialled showing the versatility of the Bayer liquor-ash combination for making geopolymers.

  3. Treatment of White Phosphorus and Other Chemical Burn Injuries at One Burn Center Over a 51-year Period

    DTIC Science & Technology

    2004-01-01

    cellulose or lauryl sulfate , avoidance of copper- sulfate soaked pads, and use of prompt water or saline rinse following application [19–22,24]. These...0 1 1 Diesel 0 0 1 1 Oven cleaner 0 0 5 5 JP4 fuel 0 0 1 1 Phenol 0 2 2 4 Fluorocarbon 0 2 1 3 Paint thinner 0 1 0 1 Triethylene gycol 0 1 0 1 Sodium ...ammonia 6.8 3.7 Hydrochloric acid 5.6 3.1 Sulfuric acid 4.7 6.5 Polychlorinated biphenyls 2.8 23 Toluene 2.4 1.4 Sodium hydroxide 1.9 2.6 Nitric acid 1.5

  4. Migration of DEHP and DINP into dust from PVC flooring products at different surface temperature.

    PubMed

    Jeon, Seunghwan; Kim, Ki-Tae; Choi, Kyungho

    2016-03-15

    Phthalates are important endocrine disrupting chemicals that have been linked to various adverse human health effects. Phthalates are ubiquitously present in indoor environment and could enter humans. Vinyl or PVC floorings have been recognized as one of important sources of phthalate release to indoor environment including house dust. In the present study, we estimated the migration of di(2-ethylhexyl)phthalate (DEHP) and di-isononyl phthalate (DINP) from the flooring materials into the dust under different heating conditions. For this purpose, a small chamber specifically designed for the present study and a Field and Laboratory Emission Cell (FLEC) were used, and four major types of PVC flooring samples including two UV curing paint coated, an uncoated residential, and a wax-coated commercial type were tested. Migration of DEHP was observed for an uncoated residential type and a wax-coated commercial type flooring. After 14 days of incubation, the levels of DEHP in the dust sample was determined at room temperature on average (standard deviation) at 384 ± 19 and 481 ± 53 μg/g, respectively. In contrast, migration of DINP was not observed. The migration of DEHP was strongly influenced by surface characteristics such as UV curing coating. In the residential flooring coated with UV curing paint, migration of DEHP was not observed at room temperature. But under the heated condition, the release of DEHP was observed in the dust in the FLEC. Migration of DEHP from flooring materials increased when the flooring was heated (50 °C). In Korea, heated flooring system, or 'ondol', is very common mode of heating in residential setting, therefore the contribution of PVC flooring to the total indoor DEHP exposure among general population is expected to be greater especially during winter season when the floor is heated. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Model study of modern oil-based paint media by triacylglycerol profiling in positive and negative ionization modes.

    PubMed

    Degano, Ilaria; La Nasa, Jacopo; Ghelardi, Elisa; Modugno, Francesca; Colombini, Maria Perla

    2016-12-01

    Lipid binders have traditionally been determined in paintings by using gas chromatography/mass spectrometry (GC/MS) to identify the characteristic profiles and ratios of fatty acids . However, the presence of mixtures in contemporary and modern oil paints makes the GC/MS determination of fatty acids insufficient to fully characterize the lipid binding media. In this study we prove that triacylglycerol (TAG) profiling by high-performance liquid chromatography with high-resolution tandem mass spectrometry, using ESI in positive and negative ionization modes is highly effective. We exploited this analytical approach to study the curing and degradation processes undergone by six plant oils used in the formulation of media in modern paints, using both natural and artificial ageing experiments. We believe that is the first time that a negative ionization mode has been applied for this purpose and that a survey with HPLC-ESI-Q-ToF has been carried out to study the ageing kinetics of plant oils. TAG profiling enabled us to study the evolution over time of the constituents of modern oils, with respect to curing and ageing. The data analyzed in this study demonstrate that our approach is efficient to study the oxidation of TAGs during ageing. The data also improve current knowledge on the properties of vegetable oils, which could lead to the development of new paint materials and conservation treatments for modern and contemporary works of art. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Effects of coal-mine discharges on the quality of the Stonycreek River and its tributaries, Somerset and Cambria counties, Pennsylvania

    USGS Publications Warehouse

    Williams, Donald R.; Sams, James I.; Mulkerrin, Mary E.

    1996-01-01

    This report describes the results of a study by the U.S. Geological Survey, done in cooperation with the Somerset Conservation District, to locate and sample abandoned coal-mine discharges in the Stonycreek River Basin, to prioritize the mine discharges for remediation, and to determine the effects of the mine discharges on water quality of the Stonycreek River and its major tributaries. From October 1991 through November 1994, 270 abandoned coal-mine discharges were located and sampled. Discharges from 193 mines exceeded U.S. Environmental Protection Agency effluent standards for pH, discharges from 122 mines exceeded effluent standards for total-iron concentration, and discharges from 141 mines exceeded effluent standards for total-manganese concentration. Discharges from 94 mines exceeded effluent standards for all three constituents. Only 40 mine discharges met effluent standards for pH and concentrations of total iron and total manganese.A prioritization index (PI) was developed to rank the mine discharges with respect to their loading capacity on the receiving stream. The PI lists the most severe mine discharges in a descending order for the Stonycreek River Basin and for subbasins that include the Shade Creek, Paint Creek, Wells Creek, Quemahoning Creek, Oven Run, and Pokeytown Run Basins.Passive-treatment systems that include aerobic wetlands, compost wetlands, and anoxic limestone drains (ALD's) are planned to remediate the abandoned mine discharges. The successive alkalinity-producing-system treatment combines ALD technology with the sulfate reduction mechanism of the compost wetland to effectively remediate mine discharge. The water quality and flow of each mine discharge will determine which treatment system or combination of treatment systems would be necessary for remediation.A network of 37 surface-water sampling sites was established to determine stream-water quality during base flow. A series of illustrations show how water quality in the mainstem deteriorates downstream because of inflows from tributaries affected by acidic mine discharges. From the upstream mainstem site (site 801) to the outflow mainstem site (site 805), pH decreased from 6.8 to 4.2, alkalinity was completely depleted by inflow acidities, and total-iron discharges increased from 30 to 684 pounds per day. Total-manganese and total-sulfate discharges increased because neither constituent precipitates readily. Also, discharges of manganese and sulfate entering the mainstem from tributary streams have a cumulative effect.Oven Run and Pokeytown Run are two small tributary streams significantly affected by acidic mine drainage (AMD) that flow into the Stonycreek River near the town of Hooversville. The Pokeytown Run inflow is about 0.5 mile downstream from the Oven Run inflow. These two streams are the first major source of AMD flowing into the Stonycreek River. Data collected on the Stonycreek River above the Oven Run inflow and below the Pokeytown Run inflow show a decrease in pH from 7.6 to 5.1, a decrease in alkalinity concentration from 42 to 2 milligrams per liter, an increase in total sulfate discharge from 18 to 41 tons per day, and an increase in total iron discharge from 29 to 1,770 pounds per day. Data collected at three mainstem sites on the Stonycreek River below Oven Run and Pokeytown Run show a progressive deterioration in river water quality from AMD.Shade Creek and Paint Creek are other tributary streams to the Stonycreek River that have a significant negative effect on water quality of the Stonycreek River. One third of the abandoned-mine discharges sampled were in the Shade Creek and Paint Creek Basins.

  7. Chemical composition and strength of dolomite geopolymer composites

    NASA Astrophysics Data System (ADS)

    Aizat, E. A.; Al Bakri, A. M. M.; Liew, Y. M.; Heah, C. Y.

    2017-09-01

    The chemical composition of dolomite and the compressive strength of dolomite geopolymer composites were studied. The both composites prepared with mechanical mixer manufactured by with rotor speed of 350 rpm and curing in the oven for 24 hours at 80˚C. XRF analysis showThe dolomite raw materials contain fewer amounts of Si and Al but high Ca in its composition. Dolomite geopolymer composites with 20M of NaOH shows greater and optimum compressive strength compared to dolomite geopolymer with other NaOH molarity. This indicated better interaction of dolomite raw material and alkaline activator need high molarity of NaOH in order to increase the reactivity of dolomite.

  8. Fiber-reinforced composite substructure: load-bearing capacity of an onlay restoration and flexural properties of the material.

    PubMed

    Garoushi, Sufyan K; Lassila, Lippo V J; Tezvergil, Arzu; Vallittu, Pekka K

    2006-09-01

    The aim of this study was to determine the static load-bearing capacity of composite resin onlay restorations made of particulate filler composite (PFC) with two different types of fiber-reinforced composite (FRC) substructures. In addition, flexural properties of the material combination and the effect of polymerization devices were tested. Specimens were prepared to simulate an onlay restoration, which consisted of 2 to 3 mm of FRC layer as a substructure (short random and continuous bidirectional fiber orientation) and a 1 mm surface layer of PFC. Control specimens were prepared from plain PFC. In Group A the specimens were incrementally polymerized only with a hand-light curing unit for 40 s, while in Group B the specimens were post-cured in a light-curing oven for 15 min before they were statically loaded with a steel ball. Bar-shaped test specimens were prepared to measure the flexural properties of material combination using a three-point bending test (ISO 10477). Analysis of variance (ANOVA) revealed all specimens with a FRC substructure have higher values of static load-bearing capacity and flexural properties than those obtained with plain PFC (p<0.001). The load-bearing capacity of all the specimens decreased after post-curing and water storage. Restorations made from a material combination of FRC and PFC showed better mechanical properties than those obtained with plain PFC.

  9. Comparison of the Effect of Curing on the Properties of E-Glass/Cyanate modified Epoxy Cross Plied Laminates

    NASA Astrophysics Data System (ADS)

    Nallayan, W. Andrew; Vijayakumar, K. R.; Rasheed, Usama Tariq

    2017-05-01

    High performance polymer composite laminates that are used in Aerospace and Electronics industries requires laminates that are structurally rigid besides exhibiting high stiffness and good di electrical properties. They are required to be transparent to EM waves in order to transmit the signal with almost zero transmission loss. Response of the laminates under different loadings could hence establish a potent material combination with high structural strengths that could be used in sectors dealing with Signal transmissions. The results thus acquired can be used as a database for choosing relatively better materials for Radome and their advanced versions in the coming decades. To augment this, thin laminates with 4 plies with simple stacking configurations of 0/90/0/90 degrees as applicable to a cross plied laminates were fabricated with cyanate ester modified epoxy resin and 1200GSM E glass unidirectional fiber. Flexural and Impact strength were the properties identified for the accessing the structural responses of the Laminate as against room and oven curing conditions. FESEM images were applied to validate the experimental findings.

  10. Curing of Thick Thermoset Composite Laminates: Multiphysics Modeling and Experiments

    NASA Astrophysics Data System (ADS)

    Anandan, S.; Dhaliwal, G. S.; Huo, Z.; Chandrashekhara, K.; Apetre, N.; Iyyer, N.

    2017-11-01

    Fiber reinforced polymer composites are used in high-performance aerospace applications as they are resistant to fatigue, corrosion free and possess high specific strength. The mechanical properties of these composite components depend on the degree of cure and residual stresses developed during the curing process. While these parameters are difficult to determine experimentally in large and complex parts, they can be simulated using numerical models in a cost-effective manner. These simulations can be used to develop cure cycles and change processing parameters to obtain high-quality parts. In the current work, a numerical model was built in Comsol MultiPhysics to simulate the cure behavior of a carbon/epoxy prepreg system (IM7/Cycom 5320-1). A thermal spike was observed in thick laminates when the recommended cure cycle was used. The cure cycle was modified to reduce the thermal spike and maintain the degree of cure at the laminate center. A parametric study was performed to evaluate the effect of air flow in the oven, post cure cycles and cure temperatures on the thermal spike and the resultant degree of cure in the laminate.

  11. Acoustic emission analysis of fiber-reinforced composite in flexural testing.

    PubMed

    Alander, Pasi; Lassila, Lippo V J; Tezvergil, Arzu; Vallittu, Pekka K

    2004-05-01

    The aim of this study was to examine the emission of acoustic signals from six commercially available fiber-reinforced composites (FRC) used in the frameworks of fixed partial dentures in material bending. FRC test specimens were made of six commercially available fiber products of polyethylene or glass and five light-curing resins. FRC test specimens were polymerized with a hand light-curing unit or with a light-curing oven. The flexural test for determination of ultimate flexural strength of test specimens (n = 6) was based on the ISO 10477 standard after the specimens were stored in air or in water for two weeks. The acoustic emission (AE) signals were monitored during three-point loading test of the test specimens using a test with increasing loading levels until the specimens fractured. Generally, stress level required for the AE activity initiation ranged from 107 MPa (Ribbond) to 579 MPa (everStick). The ultimate flexural strength of FRC specimens were higher, ranging from 132 to 764 MPa, being highest with everStick and Vectris FRC, and lowest with Ribbond FRC. ANOVA showed a statistically significant difference between the initiation of AE activity and the ultimate flexural strength according to the brand (p < 0.001) storing conditions (p < 0.001) and polymerization procedure (p < 0.001). AE activity and ultimate flexural strength correlated significantly (p < 0.010, r = 0.887). The result of this study suggested that AE activity in FRC specimens started at a 19-32% lower stress level than occurred at final fracture.

  12. A Study for the Characteristic Changes Under the Repeated Thermal Exposure in the Process of Repairing Aircraft Sandwich Structures

    NASA Astrophysics Data System (ADS)

    Kim, Yun Hae; Han, Joong Won; Kim, Don Won; Choi, Byung Keun; Murakami, R.

    Delamination can be observed in the sound areas during and/or after a couple times exposure to the elevated curing temperature due to the repeated repair condition. This study was conducted for checking the degree of degradation of properties of the cured parts and delamination between skin prepreg and honeycomb core. Specimens with glass honeycomb sandwich construction and glass/epoxy prepreg were prepared. The specimens were cured 1 to 5 times at 260°F in an autoclave and each additionally exposed 50, 100 and 150 hours in the 260°F oven. Each specimen was tested for tensile strength, compressive strength, flatwise tensile strength and interlaminar shear strength. To monitor the characteristics of the resin itself, the cured resin was tested using DMA and DSC. As a results, the decrease of Tg value were observed in the specific specimen which is exposed over 50 hrs at 260°F. This means the change or degradative of resin properties is also related to the decrease of flatwise tensile properties. Accordingly, minimal exposure on the curing temperature is recommended for parts in order to prevent the delation and maintain the better condition.

  13. Corrosion-Control (CC) Program: Pilot Powder Coating Station Service Test.

    DTIC Science & Technology

    1986-03-14

    o CL oU C4 CL00 z ;,S Go 0 m~ CL - C9 uj4 U..~D o . ZC.F Go zz 2 0 I- - c t < m U, cc V V4 cg c ~ D GD...Spray Booth# Curing Oven and A2-58 UNIT TOTAL is_18 A2-1 1WOW - o 0 -1 Q S re. 10 U c Z. 2E E. a.E 8 tE 20 4AU ==- %A a 4 $AO - Lo 48 0 w 0 -IL .. 0.... 0...Laa 00 3-r Q’ IA E zo 0..0 -< 4o C a) Ia - o x c bi. l c *4 ’a a~~* coLo. 0V Ua- 41 w - a V 2 2 .8 h A a U to bo co i ac

  14. Simultaneous acoustic and dielectric real time curing monitoring of epoxy systems

    NASA Astrophysics Data System (ADS)

    Gkikas, G.; Saganas, Ch.; Grammatikos, S. A.; Aggelis, D. G.; Paipetis, A. S.

    2012-04-01

    The attainment of structural integrity of the reinforcing matrix in composite materials is of primary importance for the final properties of the composite structure. The detailed monitoring of the curing process on the other hand is paramount (i) in defining the optimal conditions for the impregnation of the reinforcement by the matrix (ii) in limiting the effects of the exotherm produced by the polymerization reaction which create unwanted thermal stresses and (iii) in securing optimal behavior in matrix controlled properties, such as off axis or shear properties and in general the durability of the composite. Dielectric curing monitoring is a well known technique for distinguishing between the different stages of the polymerization of a typical epoxy system. The technique successfully predicts the gelation and the vitrification of the epoxy and has been extended for the monitoring of prepregs. Recent work has shown that distinct changes in the properties of the propagated sound in the epoxy which undergoes polymerization is as well directly related to the gelation and vitrification of the resin, as well as to the attainment of the final properties of the resin system. In this work, a typical epoxy is simultaneously monitored using acoustic and dielectric methods. The system is isothermally cured in an oven to avoid effects from the polymerization exotherm. Typical broadband sensors are employed for the acoustic monitoring, while flat interdigital sensors are employed for the dielectric scans. All stages of the polymerization process were successfully monitored and the validity of both methods was cross checked and verified.

  15. Copper resinate: preparation, characterisation and study of degradation.

    PubMed

    Colombini, M P; Lanterna, G; Mairani, A; Matteini, M; Modugno, F; Rizzi, M

    2001-01-01

    This paper describes a method for the synthesis of Copper Resinate, which disappeared from artists' palettes in the eighteenth century. This was carried out by interpreting ancient recipes following a scientific approach. Its characterisation using Fourier Transform-Infrared Spectrometry and Gas Chromatography-Mass Spectrometry demonstrated that it is a mixture containing copper and oxidised abietic acids, mainly dehydroabietic and 7-oxo-dehydroabietic acids, formed during the preparation of the pigment and the curing of the paint layer. The composition of copper resinate paint layers, artificially aged by U.V. irradiation at 365 nm (UV), heating (T), and exposed to atmospheric pollutants (NOX) in a climatic chamber, was investigated. The combination of irradiation and temperature produced a change in colour along with a significant increase in the recovered amount of 7-oxo-dehydroabietic acid. The identification of copper resinate in a sample from an old painting should be related to the presence of the following resin compounds which are stable in the ageing process: dehydroabietic and 7-oxo-dehydroabietic acid pimaradienic acids. Photo-oxidation of the resin acids co-ordinated with copper seem to be the most probable decay mechanism responsible for the colour change in the pigment.

  16. Blackbody for metrological control of ear thermometers

    NASA Astrophysics Data System (ADS)

    Cárdenas-García, D.; Méndez-Lango, E.

    2013-09-01

    Body temperature is an important parameter in medical practice, and most of health diagnoses are made based upon measured temperature values. Non-contact measurements are attractive to both patients and physicians, and ear thermometers (ET) are part of the set of infrared thermometers for medical applications. ETs sense the tympanic membrane temperature which best represents body temperature. They take advantage of the natural high effective emissivity cavity that is formed as radiation source. To calibrate or to check the performance of ETs, we designed a high-emissivity spherical cavity as a blackbody source which can be placed in a dry block oven. Although the blackbody cavity can have any shape, we decided to build it spherical because its effective emissivity can be easily calculated in a closed form. The cavity is made of Aluminum to take advantage of its high thermal conductivity while its inner side is covered with a black paint to increase the cavity effective emissivity. Based on paint emissivity measurements and the geometrical shape, we calculated that the cavity has an effective emissivity higher than 0.999. Blackbody temperature is measured with a calibrated contact thermometer placed inside the bottom wall of the cavity. We present the design of the cavity, the experimental setup, and results of three commercial ETs compared with this cavity.

  17. Neural Network Burst Pressure Prediction in Composite Overwrapped Pressure Vessels

    NASA Technical Reports Server (NTRS)

    Hill, Eric v. K.; Dion, Seth-Andrew T.; Karl, Justin O.; Spivey, Nicholas S.; Walker, James L., II

    2007-01-01

    Acoustic emission data were collected during the hydroburst testing of eleven 15 inch diameter filament wound composite overwrapped pressure vessels. A neural network burst pressure prediction was generated from the resulting AE amplitude data. The bottles shared commonality of graphite fiber, epoxy resin, and cure time. Individual bottles varied by cure mode (rotisserie versus static oven curing), types of inflicted damage, temperature of the pressurant, and pressurization scheme. Three categorical variables were selected to represent undamaged bottles, impact damaged bottles, and bottles with lacerated hoop fibers. This categorization along with the removal of the AE data from the disbonding noise between the aluminum liner and the composite overwrap allowed the prediction of burst pressures in all three sets of bottles using a single backpropagation neural network. Here the worst case error was 3.38 percent.

  18. Notched Strength Allowables and Inplane Shear Strength of AS4/VRM-34 Textile Laminates

    NASA Technical Reports Server (NTRS)

    Grenoble, Ray W.; Johnston, William M.

    2013-01-01

    Notched and unnotched strength allowables were developed for a textile composite to provide input data to analytical structural models based on the Pultruded Rod Stiffened Efficient Unitized Structure (PRSEUS) concept. Filled-hole tensile strength, filled-hole compressive strength, and inplane shear strength along stitch lines have been measured. The material system evaluated in this study is based on warp-knitted preforms of AS4 carbon fibers and VRM-34 epoxy resin, which have been processed via resin infusion and oven curing. All specimens were tested in as-fabricated (dry) condition. Filled-hole strengths were evaluated with and without through-thickness stitching. The effects of scaling on filled-hole tensile strength were evaluated by testing specimens in two widths, but with identical width / hole-diameter ratios. Inplane shear specimens were stitched in two configurations, and two specimen thicknesses were tested for each stitch configuration.

  19. Advanced composite rudders for DC-10 aircraft: Design, manufacturing, and ground tests

    NASA Technical Reports Server (NTRS)

    Lehman, G. M.; Purdy, D. M.; Cominsky, A.; Hawley, A. V.; Amason, M. P.; Kung, J. T.; Palmer, R. J.; Purves, N. B.; Marra, P. J.; Hancock, G. R.

    1976-01-01

    Design synthesis, tooling and process development, manufacturing, and ground testing of a graphite epoxy rudder for the DC-10 commercial transport are discussed. The composite structure was fabricated using a unique processing method in which the thermal expansion characteristics of rubber tooling mandrels were used to generate curing pressures during an oven cure cycle. The ground test program resulted in certification of the rudder for passenger-carrying flights. Results of the structural and environmental tests are interpreted and detailed development of the rubber tooling and manufacturing process is described. Processing, tooling, and manufacturing problems encountered during fabrication of four development rudders and ten flight-service rudders are discussed and the results of corrective actions are described. Non-recurring and recurring manufacturing labor man-hours are tabulated at the detailed operation level. A weight reduction of 13.58 kg (33 percent) was attained in the composite rudder.

  20. In situ simultaneous strain and temperature measurement of adaptive composite materials using a fiber Bragg grating based sensor

    NASA Astrophysics Data System (ADS)

    Yoon, Hyuk-Jin; Costantini, Daniele M.; Michaud, Veronique; Limberger, Hans G.; Manson, Jan-Anders; Salathe, Rene P.; Kim, Chun-Gon; Hong, Chang-Sun

    2005-05-01

    An optical fiber sensor to simultaneously measure strain and temperature was designed and embedded into an adaptive composite laminate which exhibits a shape change upon thermal activation. The sensor is formed by two fiber Bragg gratings, which are written in optical fibers with different core dopants. The two gratings were spliced close to each other and a sensing element resulted with Bragg gratings of similar strain sensitivity but different response to temperature. This is due to the dependence of the fiber thermo-optic coefficient on core dopants and relative concentrations. The sensor was tested on an adaptive composite laminate made of unidirectional Kevlar-epoxy pre-preg plies. Several 150μm diameter pre-strained NiTiCu shape memory alloy wires were embedded in the composite laminate together with one fiber sensor. Simultaneous monitoring of strain and temperature during the curing process and activation in an oven was demonstrated.

  1. Surface modification of commercial seawater reverse osmosis membranes by grafting of hydrophilic monomer blended with carboxylated multiwalled carbon nanotubes

    NASA Astrophysics Data System (ADS)

    Vatanpour, Vahid; Zoqi, Naser

    2017-02-01

    In this study, modification of commercial seawater reverse osmosis membranes was carried out with simultaneous use of surface grafting and nanoparticle incorporation. Membrane grafting with a hydrophilic acrylic acid monomer and thermal initiator was used to increase membrane surface hydrophilicity. The used nanomaterial was carboxylated multiwalled carbon nanotubes (MWCNTs), which were dispersed in the grafting solution and deposited on membrane surface to reduce fouling by creating polymer brushes and hydrodynamic resistance. Effectiveness of the grafting process (formation of graft layer on membrane surface) was proved by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) analyses. Increase of membrane surface hydrophilicity was approved with contact angle test. First, the grafting was performed on the membrane surfaces with different monomer concentrations, various contact times and several membrane curing times (three variables for optimization). The modified membranes were tested by a cross-flow setup using saline solution for permeability and rejection tests, and bovine serum albumin (BSA) solution for fouling test. The results showed that the modified membranes with 0.75 M of monomer, 3 min contact time and 80 min curing time in an oven at 50 °C presented the highest flux and lowest rejection decline related to the commercial reverse osmosis membrane. In the next step, the optimum grafting condition was selected and the nanotubes with different weight percentages were dispersed in the acrylic acid monomer solution. The membrane containing 0.25 wt% COOH-MWCNTs showed the highest fouling resistance.

  2. Real-time measurement system for tracking birefringence, weight, thickness, and surface temperature during drying of solution cast coatings and films

    NASA Astrophysics Data System (ADS)

    Unsal, E.; Drum, J.; Yucel, O.; Nugay, I. I.; Yalcin, B.; Cakmak, M.

    2012-02-01

    This paper describes the design and performance of a new instrument to track temporal changes in physical parameters during the drying behavior of solutions, as well as curing of monomers. This real-time instrument follows in-plane and out-of-plane birefringence, weight, thickness, and surface temperature during the course of solidification of coatings and films through solvent evaporation and thermal or photocuring in a controlled atmosphere. It is specifically designed to simulate behavior of polymer solutions inside an industrial size, continuous roll-to-roll solution casting line and other coating operations where resins are subjected to ultraviolet (UV) curing from monomer precursors. Controlled processing parameters include air speed, temperature, initial cast thickness, and solute concentration, while measured parameters are thickness, weight, film temperature, in-plane and out-of-plane birefringence. In this paper, we illustrate the utility of this instrument with solution cast and dried poly (amide-imide)/DMAc (Dimethylacetamide) solution, water based black paint, and organo-modified clay/NMP (N-Methylpyrrolidone) solution. In addition, the physical changes that take place during UV photo polymerization of a monomer are tracked. This instrument is designed to be generic and it can be used for tracking any drying/swelling/solidification systems including paper, foodstuffs such as; grains, milk as well as pharmaceutical thin paste and slurries.

  3. Competitive position of natural gas: Industrial baking

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Minsker, B.S.; Salama, S.Y.

    Industrial baking is one of the largest natural gas consumers in the food industry. In 1985, bread, rolls, cookies, and crackers accounted for over 82 percent of all baked goods production. Bread accounting for 46 percent of all production. The baking industry consumed approximately 16 trillion Btu in 1985. About 93 percent was natural gas, while distillate fuel oil accounted for seven percent, and electricity accounted for much less than one percent. The three main types of baking ovens are the single lap, tunnel, and Lanham ovens. In the single lap oven, trays carry the product back and forth throughmore » the baking chamber once. The single lap oven is the most common type of oven and is popular due to its long horizontal runs, extensive steam zone, and simple construction. The tunnel oven is slightly more efficient and more expensive that the single lap oven. IN the tunnel oven, the hearth is a motorized conveyor which passes in a straight line through a series of heating zones, with loading and unloading occurring at opposite ends of the oven. The advantages of the tunnel oven include flexibility with respect to pan size and simple, accurate top and bottom heat control. The tunnel oven is used exclusively in the cookie and cracker baking, with the product being deposited directly on the oven band. The most recently developed type of oven is the Lanham oven. The Lanham oven is the most efficient type of oven, with a per pound energy consumption approaching the practical minimum for baking bread. Between one--half and two--thirds of all new industrial baking ovens are Lanham ovens. In the Lanham oven, the product enters the oven near the top of the chamber, spirals down through a series of heating zones, and exits near the bottom of the oven. The oven is gas--fired directly by ribbon burners. 31 refs.« less

  4. 40 CFR 63.3165 - How do I determine the emission capture system efficiency?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... purposes of this subpart, a bake oven air seal is not considered a natural draft opening in a PTE or a... between the bake oven air seal and the bake oven is into the bake oven. You may use lightweight strips of... as a natural draft opening. You cannot count air flowing from a bake oven air seal into a bake oven...

  5. 40 CFR 63.302 - Standards for by-product coke oven batteries.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... batteries. 63.302 Section 63.302 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.302 Standards for by-product coke oven batteries... oven emissions from each affected existing by-product coke oven battery that exceed any of the...

  6. 40 CFR 63.302 - Standards for by-product coke oven batteries.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... batteries. 63.302 Section 63.302 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.302 Standards for by-product coke oven batteries... oven emissions from each affected existing by-product coke oven battery that exceed any of the...

  7. 40 CFR 63.302 - Standards for by-product coke oven batteries.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... batteries. 63.302 Section 63.302 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.302 Standards for by-product coke oven batteries... oven emissions from each affected existing by-product coke oven battery that exceed any of the...

  8. 40 CFR 63.302 - Standards for by-product coke oven batteries.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... batteries. 63.302 Section 63.302 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.302 Standards for by-product coke oven batteries... oven emissions from each affected existing by-product coke oven battery that exceed any of the...

  9. 40 CFR 63.302 - Standards for by-product coke oven batteries.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... batteries. 63.302 Section 63.302 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.302 Standards for by-product coke oven batteries... oven emissions from each affected existing by-product coke oven battery that exceed any of the...

  10. Physical optics for oven-plate scattering prediction

    NASA Technical Reports Server (NTRS)

    Baldauf, J.; Lambert, K.

    1991-01-01

    An oven assembly design is described, which will be used to determine the effects of temperature on the electrical properties of materials which are used as coatings for metal plates. Experimentally, these plates will be heated to a very high temperature in the oven assembly, and measured using a microwave reflectance measurement system developed for the NASA Lewis Research Center, Near-Field Facility. One unknown in this measurement is the effect that the oven assembly will have on the reflectance properties of the plate. Since the oven will be much larger than the plate, the effect could potentially be significant as the size of the plate becomes smaller. Therefore, it is necessary to predict the effect of the oven on the measurement of the plate. A method for predicting the oven effect is described, and the theoretical oven effect is compared to experimental results of the oven material. The computer code which is used to predict the oven effect is also described.

  11. No-Oven, No-Autoclave Composite Processing

    NASA Technical Reports Server (NTRS)

    Rauscher, Michael D.

    2015-01-01

    Very large composite structures, such as those used in NASA's Space Launch System, push the boundaries imposed by current autoclaves. New technology is needed to maintain composite performance and free manufacturing engineers from the restraints of curing equipment size limitations. Recent efforts on a Phase II project by Cornerstone Research Group, Inc. (CRG), have advanced the technology and manufacturing readiness levels of a unique two-part epoxy resin system. Designed for room-temperature infusion of a dry carbon preform, the system includes a no-heat-added cure that delivers 350 F composite performance in a matter of hours. This no-oven, no-autoclave (NONA) composite processing eliminates part-size constraints imposed by infrastructure and lowers costs by increasing throughput and reducing capital-specific, process-flow bottlenecks. As a result of the Phase II activity, NONA materials and processes were used to make high-temperature composite tooling suitable for further production of carbon-epoxy laminates and honeycomb/ sandwich-structure composites with an aluminum core. The technology platform involves tooling design, resin infusion processing, composite part design, and resin chemistry. The various technology elements are combined to achieve a fully cured part. The individual elements are not unusual, but they are combined in such a way that enables proper management of the heat generated by the epoxy resin during cure. The result is a self-cured carbon/ epoxy composite part that is mechanically and chemically stable at temperatures up to 350 F. As a result of the successful SBIR effort, CRG has launched NONA Composites as a spinoff subsidiary. The company sells resin to end users, fabricates finished goods for customers, and sells composite tooling made with NONA materials and processes to composite manufacturers.

  12. 40 CFR 63.3165 - How do I determine the emission capture system efficiency?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    .... For purposes of this subpart, a bake oven air seal is not considered a natural draft opening in a PTE... interface between the bake oven air seal and the bake oven is into the bake oven. You may use lightweight... air seal as a natural draft opening. You cannot count air flowing from a bake oven air seal into a...

  13. 40 CFR 63.3165 - How do I determine the emission capture system efficiency?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    .... For purposes of this subpart, a bake oven air seal is not considered a natural draft opening in a PTE... interface between the bake oven air seal and the bake oven is into the bake oven. You may use lightweight... air seal as a natural draft opening. You cannot count air flowing from a bake oven air seal into a...

  14. Validation of a combi oven cooking method for preparation of chicken breast meat for quality assessment.

    PubMed

    Zhuang, H; Savage, E M

    2008-10-01

    Quality assessment results of cooked meat can be significantly affected by sample preparation with different cooking techniques. A combi oven is a relatively new cooking technique in the U.S. market. However, there was a lack of published data about its effect on quality measurements of chicken meat. Broiler breast fillets deboned at 24-h postmortem were cooked with one of the 3 methods to the core temperature of 80 degrees C. Cooking methods were evaluated based on cooking operation requirements, sensory profiles, Warner-Bratzler (WB) shear and cooking loss. Our results show that the average cooking time for the combi oven was 17 min compared with 31 min for the commercial oven method and 16 min for the hot water method. The combi oven did not result in a significant difference in the WB shear force values, although the cooking loss of the combi oven samples was significantly lower than the commercial oven and hot water samples. Sensory profiles of the combi oven samples did not significantly differ from those of the commercial oven and hot water samples. These results demonstrate that combi oven cooking did not significantly affect sensory profiles and WB shear force measurements of chicken breast muscle compared to the other 2 cooking methods. The combi oven method appears to be an acceptable alternative for preparing chicken breast fillets in a quality assessment.

  15. Optimization of combined microwave-hot air roasting of malt based on energy consumption and neo-formed contaminants content.

    PubMed

    Akkarachaneeyakorn, S; Laguerre, J C; Tattiyakul, J; Neugnot, B; Boivin, P; Morales, F J; Birlouez-Aragon, I

    2010-05-01

    To produce specialty malt, malts were roasted by combined microwave-hot air at various specific microwave powers (SP = 2.5 to 3 W/g), microwave heating times (t(mw) = 3.3 to 3.5 min), oven temperatures (T(oven) = 180 to 220 degrees C), and oven heating times (t(oven) = 60 to 150 min). The response variables, color, energy consumption by microwave (E(mw)) and oven (E(oven)), total energy consumption (E(tot)), quantity of neo-formed contaminants (NFCs), which include hydroxymethylfurfural, furfural, furan, and acrylamide were determined. Response surface methodology (RSM) was performed to analyze and predict the optimum conditions for the specialty malt. Production using combined microwave-hot air roasting process based on minimum energy consumption and level of NFCs. At 95% confident level, SP, T(oven), and t(oven) were the most influencing effects with regard to E(tot), whereas t(mw) did not affect E(tot). T(oven) and t(oven) significantly affected malt color. Only T(oven) significantly influenced the NFCs content. The optimum parameters were: SP = 2.68 W/g for 3.44 min, T(oven) = 206 degrees C for 136 min for coffee malt, SP = 2.5 W/g for 3.48 min, T(oven) = 214 degrees C for 136 min for chocolate malt, and SP = 2.5 W/g for 3.48 min, T(oven) = 211 degrees C for 150 min for black malt. Comparing with conventional process, combined microwave-hot air reduced E(tot) by approximately 40%, 26%, and 26% for coffee, chocolate, and black malts, respectively, and reduced HMF, furfural, furan, and acrylamide contents by 40%, 18%, 23%, and 95%, respectively, for black malt. An important goal for research institutions and the brewery industry is to produce colored malt by combining microwave and hot air roasting, while saving energy, getting desirable color, and avoiding the formation of carcinogenic and toxic neo-formed contaminants (NFCs). Therefore, one objective of this study was to compare energy consumption and content of NFCs during roasting of malt by hot air-only and combined microwave-hot air processes as well as to determine the effect of specific power, microwave processing time, oven temperature, and oven processing time during combined microwave-hot air roasting. Another objective was to predict the optimum conditions for the production of coffee, chocolate, and black malts.

  16. 40 CFR 63.303 - Standards for nonrecovery coke oven batteries.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... batteries. 63.303 Section 63.303 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.303 Standards for nonrecovery coke oven batteries... existing nonrecovery coke oven battery that exceed any of the following emission limitations or...

  17. 40 CFR 63.303 - Standards for nonrecovery coke oven batteries.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... batteries. 63.303 Section 63.303 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.303 Standards for nonrecovery coke oven batteries... existing nonrecovery coke oven battery that exceed any of the following emission limitations or...

  18. 40 CFR 63.303 - Standards for nonrecovery coke oven batteries.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... batteries. 63.303 Section 63.303 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.303 Standards for nonrecovery coke oven batteries... existing nonrecovery coke oven battery that exceed any of the following emission limitations or...

  19. 40 CFR 63.303 - Standards for nonrecovery coke oven batteries.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... batteries. 63.303 Section 63.303 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.303 Standards for nonrecovery coke oven batteries... existing nonrecovery coke oven battery that exceed any of the following emission limitations or...

  20. Recent Advances in Analytical Pyrolysis to Investigate Organic Materials in Heritage Science.

    PubMed

    Degano, Ilaria; Modugno, Francesca; Bonaduce, Ilaria; Ribechini, Erika; Colombini, Maria Perla

    2018-06-18

    The molecular characterization of organic materials in samples from artworks and historical objects traditionally entailed qualitative and quantitative analyses by HPLC and GC. Today innovative approaches based on analytical pyrolysis enable samples to be analysed without any chemical pre-treatment. Pyrolysis, which is often considered as a screening technique, shows previously unexplored potential thanks to recent instrumental developments. Organic materials that are macromolecular in nature, or undergo polymerization upon curing and ageing can now be better investigated. Most constituents of paint layers and archaeological organic substances contain major insoluble and chemically non-hydrolysable fractions that are inaccessible to GC or HPLC. To date, molecular scientific investigations of the organic constituents of artworks and historical objects have mostly focused on the minor constituents of the sample. This review presents recent advances in the qualitative and semi-quantitative analyses of organic materials in heritage objects based on analytical pyrolysis coupled with mass spectrometry. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. 40 CFR 63.304 - Standards for compliance date extension.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.304 Standards for compliance date extension. (a) An owner or operator of an existing coke oven battery (including a cold-idle coke oven battery), a padup rebuild, or a brownfield coke oven battery, may elect an extension of the compliance date for...

  2. Inhalation trauma due to overheating in a microwave oven.

    PubMed Central

    Zanen, A L; Rietveld, A P

    1993-01-01

    The microwave oven is a kitchen appliance that has become increasingly popular in recent years. In some instances the temperature in the microwave oven can become exceedingly high. A case is discussed of a patient with respiratory distress after inhalation of gas from an overheated microwave oven. Images PMID:8497834

  3. Influence of final baking technologies in partially baked frozen gluten-free bread quality.

    PubMed

    Aguilar, Núria; Albanell, Elena; Miñarro, Begoña; Gallardo, Joan; Capellas, Marta

    2015-03-01

    The effect of final baking in convection oven (FBC), microwave oven (FBM), and microwave oven with susceptor packaging material (FBMS) on partially baked (PB) frozen gluten-free bread characteristics was investigated. Specific volume and crust color of loaves were measured at day 0. Bread moisture, water activity, and crumb and crust texture (at 15, 45, and 90 min after baking) were analyzed at day 0 and after 28 d of frozen storage (-18 °C). Volatile compounds from breads baked in convection oven or microwave oven with susceptor packaging material were also evaluated. Bread finally baked in convection oven or in microwave oven with susceptor packaging increased crust browning. Crumb and roll hardness increased with time after final baking (measured at 15, 45, 90 min) and after 28 d of frozen storage. Bread finally baked in microwave oven was the hardest, due to high water losses. At day 0, bread finally baked in convection oven had softer crumb than bread finally baked in microwave oven with susceptor packaging but, after 28 d of frozen storage, there were no differences between them. Moreover, FBC and FBMS rendered gluten-free breads that could not be distinguished in a triangular test and had the same volatile compounds profile. In conclusion, FBMS could be an alternative to FBC. © 2015 Institute of Food Technologists®

  4. Reflow-oven-processing of pressureless sintered-silver interconnects

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wereszczak, Andrew A.; Chen, Branndon R.; Oistad, Brian A.

    Here, a method was developed to pressurelessly fabricate strong and consistent sinterable-silver joints or interconnects using reflow oven heating. Circular sinterable-silver interconnects, having nominal diameter of 5 mm and 0.1 mm thickness were stencil printed, contact-dried, and then pressurelessly sinter-bonded to Au-plated direct copper bonded ceramic substrates at 250 °C in ambient air. That sintering was done in either a reflow oven or a convective oven (latter being a conventional heating source for processing sinterable-silver). Consistently strong (>40 MPa) interconnects were produced with reflow oven heating and were as strong as those produced with convective oven heating. This is significantmore » because reflow oven technology affords better potential for continuous mass production and it was shown that strong sintered-silver bonds can indeed be achieved with its use.« less

  5. 40 CFR 63.303 - Standards for nonrecovery coke oven batteries.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... batteries. 63.303 Section 63.303 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.303 Standards for nonrecovery coke oven batteries... existing nonrecovery coke oven battery that exceed any of the following emission limitations or...

  6. Designing of Hybrid Structured Glass Laminated Transparent Nano Composites through Vacuum infusion Technique

    NASA Astrophysics Data System (ADS)

    Mukherji, A.; Tarapure, N. D.; Wakure, G. N.

    2017-05-01

    Glass is the most commonly used transparent material. However, glass is not suitable in applications where low weight, high strength is required. The present invention comprises a method of making a Transparent Glass Laminated Nano composite product. The product contains a Bidirectionally oriented E-Glass Fabric an essentially bidirectional yarn woven fabrics is stretched Bidirectionally by specially fabricated steel frame associated with both co and counter rotating device. These fibers include glass fibrics/cloths or mixtures of any of these. The synthetic fiber may be any synthetic silica based oven waived bi-directional or Uni-directional fabrics. Engaged gear provided in the device develops uniform tension on fabric, in both direction. Nano particle dispersed resin to be used is formulated with their respective curing agents and extenders. The formulated resin contains 0.1-0.5% of Nano additives and the product composed from 5-10 % of Glass fabric, between 10 to 20 % of ordinary glass, and between 60-80 % of the product is the Nano particles dispersed formulated resin, all measured by volume.

  7. Selective interference with pacemaker activity by electrical dental devices.

    PubMed

    Miller, C S; Leonelli, F M; Latham, E

    1998-01-01

    We sought to determine whether electromagnetic interference with cardiac pacemakers occurs during the operation of contemporary electrical dental equipment. Fourteen electrical dental devices were tested in vitro for their ability to interfere with the function of two Medtronics cardiac pacemakers (one a dual-chamber, bipolar Thera 7942 pacemaker, the other a single-chamber, unipolar Minix 8340 pacemaker). Atrial and ventricular pacemaker output and electrocardiographic activity were monitored by means of telemetry with the use of a Medtronics 9760/90 programmer. Atrial and ventricular pacing were inhibited by electromagnetic interference produced by the electrosurgical unit up to a distance of 10 cm, by the ultrasonic bath cleaner up to 30 cm, and by the magnetorestrictive ultrasonic scalers up to 37.5 cm. In contrast, operation of the amalgamator, electric pulp tester, composite curing light, dental handpieces, electric toothbrush, microwave oven, dental chair and light, ENAC ultrasonic instrument, radiography unit, and sonic scaler did not alter pacing rate or rhythm. These results suggest that certain electrosurgical and ultrasonic instruments may produce deleterious effects in medically fragile patients with cardiac pacemakers.

  8. 40 CFR 63.305 - Alternative standards for coke oven doors equipped with sheds.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries § 63.305 Alternative standards for coke oven doors equipped with sheds. (a) The owner or operator of a new or existing coke oven battery... the efficiency of the control device for removal of particulate matter by conducting measurements at...

  9. 40 CFR 63.305 - Alternative standards for coke oven doors equipped with sheds.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries § 63.305 Alternative standards for coke oven doors equipped with sheds. (a) The owner or operator of a new or existing coke oven battery... the efficiency of the control device for removal of particulate matter by conducting measurements at...

  10. 40 CFR 63.3171 - How do I demonstrate initial compliance?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... of electrodeposition bake oven emissions. You must show that the electrodeposition bake oven meets... of the exhaust gases from the bake oven to an add-on control device. For purposes of this showing, an electrodeposition bake oven air seal is not considered a natural draft opening provided you demonstrate that the...

  11. 40 CFR 63.3171 - How do I demonstrate initial compliance?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... of electrodeposition bake oven emissions. You must show that the electrodeposition bake oven meets... of the exhaust gases from the bake oven to an add-on control device. For purposes of this showing, an electrodeposition bake oven air seal is not considered a natural draft opening provided you demonstrate that the...

  12. 40 CFR 63.305 - Alternative standards for coke oven doors equipped with sheds.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries § 63.305 Alternative standards for coke oven doors equipped with sheds. (a) The owner or operator of a new or existing coke oven battery... the efficiency of the control device for removal of particulate matter by conducting measurements at...

  13. 40 CFR 63.3171 - How do I demonstrate initial compliance?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... of electrodeposition bake oven emissions. You must show that the electrodeposition bake oven meets... of the exhaust gases from the bake oven to an add-on control device. For purposes of this showing, an electrodeposition bake oven air seal is not considered a natural draft opening provided you demonstrate that the...

  14. 40 CFR 63.3176 - What definitions apply to this subpart?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... automobiles or light-duty trucks, including coating facilities and processes. Bake oven air seal means an entry or entry vestibule to or an exit or exit vestibule from a bake oven which isolates the bake oven... exit or exit vestibule) the bake oven. No significant VOC generating activity takes place in a bake...

  15. 16 CFR 255.1 - General considerations.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... an uncooked chicken in the oven roasting bag and places the bag in one oven. He then takes a chicken roasting bag from a second oven, removes from the bag what appears to be a perfectly cooked chicken, tastes... conduct. Example 4: A well-known celebrity appears in an infomercial for an oven roasting bag that...

  16. Light curing through glass ceramics: effect of curing mode on micromechanical properties of dual-curing resin cements.

    PubMed

    Flury, Simon; Lussi, Adrian; Hickel, Reinhard; Ilie, Nicoleta

    2014-04-01

    The aim of this study was to investigate micromechanical properties of five dual-curing resin cements after different curing modes including light curing through glass ceramic materials. Vickers hardness (VH) and indentation modulus (Y HU) of Panavia F2.0, RelyX Unicem 2 Automix, SpeedCEM, BisCem, and BeautiCem SA were measured after 1 week of storage (37 °C, 100 % humidity). The resin cements were tested following self-curing or light curing with the second-generation light-emitting diode (LED) curing unit Elipar FreeLight 2 in Standard Mode (1,545 mW/cm(2)) or with the third-generation LED curing unit VALO in High Power Mode (1,869 mW/cm(2)) or in XtraPower Mode (3,505 mW/cm(2)). Light curing was performed directly or through glass ceramic discs of 1.5 or 3 mm thickness of IPS Empress CAD or IPS e.max CAD. VH and Y HU were analysed with Kruskal-Wallis tests followed by pairwise Wilcoxon rank sum tests (α = 0.05). RelyX Unicem 2 Automix resulted in the highest VH and Y HU followed by BeautiCem SA, BisCem, SpeedCEM, and finally Panavia F2.0. Self-curing of RelyX Unicem 2 Automix and SpeedCEM lowered VH and Y HU compared to light curing whereas self-curing of Panavia F2.0, BisCem, and BeautiCem SA led to similar or significantly higher VH and Y HU compared to light curing. Generally, direct light curing resulted in similar or lower VH and Y HU compared to light curing through 1.5-mm-thick ceramic discs. Light curing through 3-mm-thick discs of IPS e.max CAD generally reduced VH and Y HU for all resin cements except SpeedCEM, which was the least affected by light curing through ceramic discs. The resin cements responded heterogeneously to changes in curing mode. The applied irradiances and light curing times adequately cured the resin cements even through 1.5-mm-thick ceramic discs. When light curing resin cements through thick glass ceramic restorations, clinicians should consider to prolong the light curing times even with LED curing units providing high irradiances.

  17. 40 CFR 63.3165 - How do I determine the emission capture system efficiency?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., a bake oven air seal is not considered a natural draft opening in a PTE or a temporary total enclosure provided you demonstrate that the direction of air movement across the interface between the bake oven air seal and the bake oven is into the bake oven. You may use lightweight strips of fabric or...

  18. 40 CFR 63.304 - Standards for compliance date extension.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.304 Standards for compliance date extension. (a) An owner or operator of an existing coke oven battery (including a cold-idle coke oven battery), a padup rebuild, or a brownfield coke oven battery, may elect an extension of the compliance date for...

  19. 40 CFR 63.304 - Standards for compliance date extension.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.304 Standards for compliance date extension. (a) An owner or operator of an existing coke oven battery (including a cold-idle coke oven battery), a padup rebuild, or a brownfield coke oven battery, may elect an extension of the compliance date for...

  20. Space shuttle/food system study. Volume 2: Supporting appendices, oven study

    NASA Technical Reports Server (NTRS)

    1975-01-01

    Calculations and data regarding the development of a galley oven for use in the space shuttle are presented. Heat flow, heat transfer, and food heating characteristics are given for various oven designs. A design approach to guarantee structural reliability is also presented, in which the oven closure, door, and basic mounting points are considered.

  1. 40 CFR 63.3165 - How do I determine the emission capture system efficiency?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., a bake oven air seal is not considered a natural draft opening in a PTE or a temporary total enclosure provided you demonstrate that the direction of air movement across the interface between the bake oven air seal and the bake oven is into the bake oven. You may use lightweight strips of fabric or...

  2. Reflow-oven-processing of pressureless sintered-silver interconnects

    DOE PAGES

    Wereszczak, Andrew A.; Chen, Branndon R.; Oistad, Brian A.

    2018-01-04

    Here, a method was developed to pressurelessly fabricate strong and consistent sinterable-silver joints or interconnects using reflow oven heating. Circular sinterable-silver interconnects, having nominal diameter of 5 mm and 0.1 mm thickness were stencil printed, contact-dried, and then pressurelessly sinter-bonded to Au-plated direct copper bonded ceramic substrates at 250 °C in ambient air. That sintering was done in either a reflow oven or a convective oven (latter being a conventional heating source for processing sinterable-silver). Consistently strong (>40 MPa) interconnects were produced with reflow oven heating and were as strong as those produced with convective oven heating. This is significantmore » because reflow oven technology affords better potential for continuous mass production and it was shown that strong sintered-silver bonds can indeed be achieved with its use.« less

  3. Effectiveness of modified 1-hour air-oven moisture methods for determining popcorn moisture

    USDA-ARS?s Scientific Manuscript database

    Two of the most commonly used approved grain moisture air-oven reference methods are the air oven method ASAE S352.2, which requires long heating time (72-h) for unground samples, and the AACC 44-15.02 air-oven method, which dries a ground sample for 1 hr, but there is specific moisture measurement ...

  4. Measurement of the full-field polymerization shrinkage and depth of cure of dental composites using digital image correlation.

    PubMed

    Li, Jianying; Fok, Alex S L; Satterthwaite, Julian; Watts, David C

    2009-05-01

    The aim of this study was to measure the full-field polymerization shrinkage of dental composites using optical image correlation method. Bar specimens of cross-section 4mm x 2mm and length 10mm approximately were light cured with two irradiances, 450 mW/cm(2) and 180 mW/cm(2), respectively. The curing light was generated with Optilux 501 (Kerr) and the two different irradiances were achieved by adjusting the distance between the light tip and the specimen. A single-camera 2D measuring system was used to record the deformation of the composite specimen for 30 min at a frequency of 0.1 Hz. The specimen surface under observation was sprayed with paint to produce sufficient contrast to allow tracking of individual points on the surface. The curing light was applied to one end of the specimen for 40s during which the painted surface was fully covered. After curing, the cover was removed immediately so that deformation of the painted surface could be recorded by the camera. The images were then analyzed with specialist software and the volumetric shrinkage determined along the beam length. A typical shrinkage strain field obtained on a specimen surface was highly non-uniform, even at positions of constant distance from the irradiation surface, indicating possible heterogeneity in material composition and shrinkage behavior in the composite. The maximum volumetric shrinkage strain of approximately 1.5% occurred at a subsurface distance of about 1mm, instead of at the irradiation surface. After reaching its peak value, the shrinkage strain then gradually decreased with increasing distance along the beam length, before leveling off to a value of approximately 0.2% at a distance of 4-5mm. The maximum volumetric shrinkage obtained agreed well with the value of 1.6% reported by the manufacturer for the composite examined in this work. Using irradiance of 180 mW/cm(2) resulted in only slightly less polymerization shrinkage than using irradiance of 450 mW/cm(2). Compared to the other measurement methods, the image correlation method is capable of producing full-field information about the polymerization shrinkage behavior of dental composites.

  5. 40 CFR 63.3171 - How do I demonstrate initial compliance?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... of electrodeposition bake oven emissions. You must show that the electrodeposition bake oven meets... of the exhaust gases from the bake oven to an add-on control device. For purposes of this showing, an electrodeposition bake oven air seal is not considered a natural draft opening provided you demonstrate that the...

  6. 40 CFR 63.3171 - How do I demonstrate initial compliance?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... of electrodeposition bake oven emissions. You must show that the electrodeposition bake oven meets... of the exhaust gases from the bake oven to an add-on control device. For purposes of this showing, an electrodeposition bake oven air seal is not considered a natural draft opening provided you demonstrate that the...

  7. 40 CFR 63.305 - Alternative standards for coke oven doors equipped with sheds.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries § 63.305 Alternative standards for coke oven doors equipped with sheds. (a) The owner or operator of a new or existing coke oven battery... the efficiency of the control device for removal of particulate matter by conducting measurements at...

  8. 40 CFR 63.305 - Alternative standards for coke oven doors equipped with sheds.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries § 63.305 Alternative standards for coke oven doors equipped with sheds. (a) The owner or operator of a new or existing coke oven battery... the efficiency of the control device for removal of particulate matter by conducting measurements at...

  9. 49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

  10. Effects of coke oven emissions and benzo[a]pyrene on blood pressure and electrocardiogram in coke oven workers.

    PubMed

    Yang, Kai; Jiang, Xuejun; Cheng, Shuqun; Chen, Chengzhi; Cao, Xianqing; Tu, Baijie

    2017-01-24

    To evaluate the effects of occupational exposures to coke oven emissions (COEs) and benzo[a]pyrene (B[a]P) on the prevalence of hypertension and abnormal electrocardiogram (ECG) in coke oven workers. We included 880 coke oven workers and 710 oxygen employees in the exposed and control groups, respectively. Blood pressure (BP), ECG, blood lipid levels, and glucose levels of all subjects were measured. COE and B[a]P concentrations at the bottom, side, and top of the oven and control plants were estimated by weighing and high-performance liquid chromatography. The COE concentration at the top and side was higher than that at the bottom (P < 0.05). The levels of B[a]P at the top and side significantly exceeded the limit value. Abnormal BP, ECG, the detection ratio of hypertension and left ventricular high voltage were significantly greater in the exposed group than in the control group (P < 0.05). The logistic regression analysis results revealed that age and B[a]P exposure were risk factors for hypertension in coke oven workers (P < 0.05) and both were risk factors for abnormal ECG (P < 0.05). Moreover, B[a]P exposure, age, and gender were risk factors for impaired fasting glucose in coke oven workers (P < 0.05). B[a]P and COE exposures are risk factors for hypertension and abnormal ECG in coke oven workers.

  11. Biomarkers of polycyclic aromatic hydrocarbon exposure in European coke oven workers.

    PubMed

    Talaska, Glenn; Thoroman, Jeff; Schuman, Brenda; Käfferlein, Heiko Udo

    2014-12-01

    Biomonitoring is an excellent method for capturing the results of all exposures, regardless of route. Coke oven workers include certain groups that have the potential for high exposure to polycyclic aromatic hydrocarbons (PAH) and other materials. Biomarkers of exposure to these agents include PAH metabolites as markers of internal dose and carcinogen-DNA adducts as measure of effective dose. The purpose of this study was to determine the levels of these biomarkers in persons with different job duties in a modern coke oven plant. We report that the mean levels of 1-hydroxypyrene (1HP) and carcinogen DNA adducts in the exfoliated urothelial cells of coke oven workers are increased the closer a group of workers is to the ovens and highest in the top oven workers with average 1HP level of 11.6 μg/l and 22 adducts per 10(9) unadducted nucleotides. Both 1HP and carcinogen DNA adduct levels increased in supervisors, area workers, side oven workers, top and side oven workers, and top oven workers, respectively. These data are the first to demonstrate an increase in target organ genotoxicity in coke oven workers and a relationship with other biomarkers. Future studies will determine the identity of the DNA adducts, their correlation with 1HP levels and the relationship between levels in individual workers. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  12. In vitro starch digestibility and expected glycemic index of pound cakes baked in two-cycle microwave-toaster and conventional oven.

    PubMed

    García-zaragoza, Francisco J; Sánchez-Pardo, María E; Ortiz-Moreno, Alicia; Bello-Pérez, Luis A

    2010-11-01

    Bread baking technology has an important effect on starch digestibility measured as its predicted glycemic index tested in vitro. The aim of this work was to evaluate the changes in predicted glycemic index of pound cake baked in a two-cycle microwave toaster and a conventional oven. The glycemic index was calculated from hydrolysis index values by the Granfeldt method. Non-significant differences (P > 0.05) were found in hydrolysis index (60.67 ± 3.96 for the product baked in microwave oven and 65.94 ± 4.09 for the product baked in conventional oven) and predicted glycemic index content (60.5 for product baked in microwave oven and 65 for the product baked in conventional oven) in freshly-baked samples. Results clearly demonstrate that the baking pound cake conventional process could be replicated using a two-cycle multifunction microwave oven, reducing the traditional baking time. Further research is required in order to achieve pound cake crumb uniformity.

  13. Characteristic analysis of peripheral blood mononuclear cell apoptosis in coke oven workers.

    PubMed

    Zhang, Hong Mei; Nie, Ji Sheng; Li, Xin; Niu, Qiao

    2012-01-01

    The aim of the present study was to determine the peripheral blood mononuclear cell (PBMC) apoptosis in coke oven workers so that we can take effective measures to protect coke oven workers. The subjects, 129 coke oven workers and 37 warehouse workers (controls), were investigated using a questionnaire to collect information about their age, working years, smoking and drinking habits, vocational history and other general information. The coke oven workers were divided into the oven-bottom group (34), oven-side group (48) and oven-top group (47) according to their working sites and environmental monitoring data. The concentration of benzo[a]pyrene (B[a]P) and the subjects' urinary 1-hydroxypyrene (1-OH-Py) levels were determined by HPLC. Additionally, the PBMCs were separated from blood samples, and the early and late apoptosis rates were determined by flow cytometry. The airborne B[a]P concentrations were 19.5 ± 13.2, 185.9 ± 38.6 and 1,623.5 ± 435.8 ng/m(3) at the bottom, side and top of the oven, respectively, and were higher than in the controls' workplaces 10.2 ± 7.6 ng/m(3). Urinary 1-OH-Py, indicating the B[a]P's internal exposure level, was significantly higher in the exposed groups than in the controls (p<0.05). Compared with the controls, the coke oven workers' PBMC apoptosis rates were significantly increased and increased in association with the B[a]P level. PBMC apoptosis increased in association with the 1-OH-Py level and coking operation years and decreased in association with years of alcohol consumption. PBMC apoptosis in the coke oven workers was associated with the 1-OH-Py level, coke operation years and years of alcohol consumption and may be induced by B[a]P.

  14. 40 CFR Appendix A to Subpart L of... - Operating Coke Oven Batteries as of April 1, 1992

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Operating Coke Oven Batteries as of... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries Pt. 63, Subpt. L, App. A Appendix A to Subpart L of Part 63—Operating Coke Oven Batteries as of April 1, 1992 No. Plant Battery 1 ABC...

  15. 40 CFR Appendix A to Subpart L of... - Operating Coke Oven Batteries as of April 1, 1992

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 10 2012-07-01 2012-07-01 false Operating Coke Oven Batteries as of... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries Pt. 63, Subpt. L, App. A Appendix A to Subpart L of Part 63—Operating Coke Oven Batteries as of April 1, 1992 No. Plant Battery 1 ABC...

  16. 40 CFR 63.7351 - Who implements and enforces this subpart?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-product coke oven battery with vertical flues, fugitive pushing emissions in § 63.7292(a) for a by-product... coke oven battery, soaking for a by-product coke oven battery in § 63.7294(a), and quenching for a coke... for a by-product coke oven battery under § 63.6(h)(9). (3) Approval of major alternatives to test...

  17. 49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

  18. 49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

  19. 40 CFR Appendix A to Subpart L of... - Operating Coke Oven Batteries as of April 1, 1992

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 10 2013-07-01 2013-07-01 false Operating Coke Oven Batteries as of... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries Pt. 63, Subpt. L, App. A Appendix A to Subpart L of Part 63—Operating Coke Oven Batteries as of April 1, 1992 No. Plant Battery 1 ABC...

  20. 40 CFR 745.233 - Lead-based paint activities requirements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Lead-based paint activities...

  1. 49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

  2. 49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

  3. Cleaner Technology in the Hard Disk Drive Manufacturing Industry: A Case Study

    NASA Astrophysics Data System (ADS)

    Moolla, Premchai; Chompu-inwai, Rungchat

    2010-10-01

    The objectives of this research are to improve raw material and energy consumption efficiency, as well as reduce defects and the use of chemicals in the arm coil assembly process of hard disk drive manufacturing in the case study company by applying the Cleaner Technology concepts. The four main sequential steps used in this research were: (1) pre-assessment, (2) assessment, (3) feasibility study, and (4) implementation. In the first step, raw data, such as process flows, raw material usage and defects data were collected. In the second step, the loss during production and causes of loss were analyzed. Opportunities to reduce raw material, chemical and energy wastage could then be recommended. The next step was to evaluate the feasibility and potential benefits of a particular Cleaner Technology opportunity. Finally, in the last step, after a thorough evaluation and implementation of the opportunities to apply Cleaner Technology, the results showed that arm coil defects could be reduced by improving the production process using the ECRS technique. ECRS stands for Eliminate, Combine, Rearrange and Simplify. This improvement reduced arm coil defect rates from 0.48% to 0.15%, thus saving approximately 139,638 Thai Baht per month. In addition, production stoppage decision made by workers was used to increase employee involvement in defect detection. Allowing workers to participate in such a decision was an effective way to reduce defect rate and could motivate workers to produce a better quality job. This resulted in arm coil defects reducing from 0.41% to 0.025%, with about 74,562 Thai Baht per month saving. Additionally, an increase in the efficiency of electricity consumption occurred, by increasing the speed of the infrared oven conveyor belt, improving average productivity from 533 pieces/hour to 560 pieces/hour, without adversely affecting product costs and quality, thus producing products of up to the value of 206,242 Thai Baht per month. Furthermore, the new two-layer curing equipment was designed, developed and used. The upper layer of the equipment was used for arm curing and the lower layer was used for arm coil curing. The result of using such equipment led to a saving of approximately 25,502 Thai Baht per month in electricity costs, without affecting product quality. The outcome of these Cleaner Technology applications was that total costs of approximately 239,702 Thai Baht per month were able to be saved.

  4. Urinary 1-hydroxypyrene and 8-hydroxydeoxyguanosine levels among coke-oven workers for 2 consecutive days.

    PubMed

    Nguyen, Thi-To-Uyen; Kawanami, Shoko; Kawai, Kazuaki; Kasai, Hiroshi; Li, Yun-Shan; Inoue, Jinro; Ngoan, Le Tran; Horie, Seichi

    2014-01-01

    This study evaluated the levels of exposure to polycyclic aromatic hydrocarbons (PAHs) and their relationship with oxidative DNA damage among Vietnamese coke-oven workers. We collected urine from 36 coke-oven workers (exposed group) at the beginning and end of the shift on 2 consecutive days. We also collected urine from 78 medical staff (control group). Information was collected by questionnaire about smoking status, drinking habit, and working position. Urinary 1-hydroxypyrene (1-OHP) and 8-hydroxydeoxyguanosine (8-OH-dG) were measured using HPLC. All statistical analyses were performed with SPSS version 19. Urinary 1-OHP was significantly higher in the coke-oven workers than in the control group (p<0.05). Top-oven workers had the highest levels of internal exposure to PAHs, followed by side-oven and then bottom-oven workers (5.41, 4.41 and 1.35 ng/mg creatinine, respectively, at the end of the shift on day 2). Urinary 8-OH-dG was significantly higher in top- and side-oven workers at the end of the shift on day 2 (4.63 and 5.88 ng/mg creatinine, respectively) than in the control group (3.85 ng/mg creatinine). Based on a multi-regression analysis, smoking status had a significant effect on urinary 8-OH-dG (p=0.049). Urinary 1-OHP tended to have a positive correlation with urinary 8-OH-dG (p=0.070). Vietnamese coke-oven workers were exposed to PAHs during their work shift. Urinary 1-OHP exceeded the recommended limit, and elevated oxidative DNA damage occurred in top- and side-oven workers on the second day of work. A tendency for positive correlation was found between urinary 1-OHP and urinary 8-OH-dG.

  5. [Association between aryl hydrocarbon receptor gene polymorphisms and chromosomal damage in coke-oven workers].

    PubMed

    Bin, Ping; Leng, Shuguang; Liang, Xuemiao; Cheng, Juan

    2007-11-01

    To investigate the association of single nucleotide polymorphisms (SNPs) or haplotypes of aryl hydrocarbon receptor (AHR) gene and chromosomal damage in peripheral blood lymphocytes among coke-oven workers. Eighty-nine coke-oven workers exposed to a high level of polycyclic aromatic hydrocarbons (PAHs) and sixty non-exposed workers were selected as the study subjects. Urinary 1-hydroxypyrene (1-OHPyr) levels were measured as the internal dose of PAHs exposure. The chromosomal damage in peripheral lymphocyte was measured by the cytokinesis-block micronucleus (CBMN) assay. Two SNPs in AHR gene, including rs6960165, rs2282885 were detected by PCR-RFLP. The AHR haplotypes were estimated by Bayesian statistical method with the software of PHASE Version 2.1. The associations between SNPs or haplotypes pairs and CBMN were assessed by analysis of covariance in the coke-oven workers and non-exposed workers. The level of 1-OHPyr among coke-oven workers was significantly higher than that among non-exposed workers (P < 0.01). The CBMN among coke-oven workers was significantly higher than that among non-exposed workers (P < 0.01). After adjusting the age and the level of 1-OHPyr, the different SNPs of AHR gene rs6960165 in coke-oven workers were related to the CBMN frequencies (P = 0.014), but no association between the different SNPs of AHR gene rs2282885 and the rates of CBMN was observed in coke-oven workers (P = 0.586), either in the controls (P = 0.308 and P = 0.415, respectively), the haplotypes in coke-oven workers were significantly related to the rates of CBMN (P = 0.007), while there was no significant association in non-exposed workers (P = 0.768). Our results suggested that SNPs rs6960165 or haplotypes of AHR were associated with the CBMN frequencies in coke-oven workers.

  6. 40 CFR 745.233 - Lead-based paint activities requirements.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Lead-based paint activities...

  7. 40 CFR 745.233 - Lead-based paint activities requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Lead-based paint activities...

  8. 40 CFR 745.233 - Lead-based paint activities requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Lead-based paint activities...

  9. [Influence of coke oven emissions on workers' blood pressure and electrocardiographic findings].

    PubMed

    Liang, J J; Yi, G L; Mao, G S; Wang, D M; Dai, X Y

    2016-09-20

    Objective: To investigate the influence of coke oven emissions on workers' blood pressure and electrocardiographic findings, and to provide a basis for the prevention and treatment of cardiovascular diseases. Methods: The concentration of coke oven emissions at the bottom, side, and top of coke ovens was determined in a coking plant. A total of 406 coke oven workers were enrolled as exposure group and 201 office staff members were enrolled as control group. Blood pressure and electrocardiographic findings were compared between the two groups, and the multivariate logistic regression analysis was performed to analyze the influencing factors for hypertension and abnormal electrocardiographic findings. Results: The concentration of coke oven emissions was the highest at the top of coke ovens, followed by the side and bottom of coke ovens, and there was a significant difference between the exposure group and the control group ( P <0.01). The exposure group had significantly higher detection rates of hypertension, abnormal electrocardiographic findings, and abnormal chest X-ray findings than the control group ( P <0.05). The logistic regression analysis showed that high concentration of coke oven emission and age were risk factors for hypertension and abnormal electrocardiographic findings ( P <0.05). The workers exposed to high-concentration coke oven emissions were more likely to experience hypertension and abnormal electrocardiographic findings than those exposed to low-concentration coke oven emissions ( OR =1.7 and 1.9). Conclusion: Besides lung injury, coke oven emissions also have adverse effects on the cardiovascular system. Therefore, more effective measures are needed to protect the health of coke oven workers.

  10. 40 CFR Appendix A to Subpart L of... - Operating Coke Oven Batteries as of April 1, 1992

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 9 2011-07-01 2011-07-01 false Operating Coke Oven Batteries as of... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries Pt. 63, Subpt. L, App. A Appendix A to Subpart L of Part 63—Operating Coke Oven Batteries as of April 1, 1992 No. Plant Battery 1 ABC...

  11. 40 CFR Appendix A to Subpart L of... - Operating Coke Oven Batteries as of April 1, 1992

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 10 2014-07-01 2014-07-01 false Operating Coke Oven Batteries as of... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries Pt. 63, Subpt. L, App. A Appendix A to Subpart L of Part 63—Operating Coke Oven Batteries as of April 1, 1992 No. Plant Battery 1 ABC...

  12. 28. CROSS SECTION OF A RECTANGULAR COKE OVEN SHOWING THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    28. CROSS SECTION OF A RECTANGULAR COKE OVEN SHOWING THE INTERNAL STRUCTURE OF THE OVEN. - Tower Hill No. 2 Mine, Approximately 0.47 mile Southwest of intersection of Stone Church Road & Township Route 561, Hibbs, Fayette County, PA

  13. Investigation into improved pavement curing materials and techniques : part 2 (phase III).

    DOT National Transportation Integrated Search

    2003-03-01

    Appropriate curing is important for concrete to obtain the designed properties. This research was conducted to evaluate the curing : effects of different curing materials and methods on pavement properties. At present the sprayed curing compound is a...

  14. A comparative study of vascular injection fluids in fresh-frozen and embalmed human cadaver forearms.

    PubMed

    Doomernik, D E; Kruse, R R; Reijnen, M M P J; Kozicz, T L; Kooloos, J G M

    2016-10-01

    Over the years, various vascular injection products have been developed to facilitate anatomical dissections. This study aimed to compare the most commonly used vascular injection products in fresh-frozen and formalin-embalmed cadaver specimens. An overview of the properties, advantages and limitations of each substance was given, and a comparison of vascular infusion procedures in both preservation methods was made. A literature search was performed in order to identify the most commonly used vascular injection products. Acrylic paint, latex, gelatin, silicone, Araldite F and Batson's No. 17 were selected for the study. One fresh-frozen and one embalmed cadaver forearm were infused with each injection product according to a uniform protocol. The curing time, skin- and subcutaneous tissue penetration, degree of filling of the arterial tree, extravasations, consistency of the injected vessels during dissection, and the costs of each injection fluid were noted. There was a large variation between the injection fluids in processing- and curing time, colour intensity, flexibility, fragility, elasticity, strength, toxicity and costs. All fluids were suitable for infusion. The penetration of injection fluid into the skin and subcutaneous tissue was significantly better in fresh-frozen specimens (P = 0.002 and P = 0.009, respectively), with significantly smaller branches casted (P = 0.004). Vascular infusion of fresh-frozen cadaver specimens results in a significantly better filled coloured arterial tree, enabling more detail to be achieved and smaller branches casted. The biomechanical properties of fresh-frozen soft tissues are less affected compared with formalin fixation. All the injection fluids studied are suitable for vascular infusion, but their different properties ensure that certain products and procedures are more suitable for specific study purposes. © 2016 Anatomical Society.

  15. Cold-Curing Structural Epoxy Resins: Analysis of the Curing Reaction as a Function of Curing Time and Thickness.

    PubMed

    Corcione, Carola Esposito; Freuli, Fabrizio; Frigione, Mariaenrica

    2014-09-22

    The curing reaction of a commercial cold-curing structural epoxy resin, specifically formulated for civil engineering applications, was analyzed by thermal analysis as a function of the curing time and the sample thickness. Original and remarkable results regarding the effects of curing time on the glass transition temperature and on the residual heat of reaction of the cold-cured epoxy were obtained. The influence of the sample thickness on the curing reaction of the cold-cured resin was also deeply investigated. A highly exothermal reaction, based on a self-activated frontal polymerization reaction, was supposed and verified trough a suitable temperature signal acquisition system, specifically realized for this measurement. This is one of the first studies carried out on the curing behavior of these peculiar cold-cured epoxy resins as a function of curing time and thickness.

  16. Effects of coke oven emissions and benzo[a]pyrene on blood pressure and electrocardiogram in coke oven workers

    PubMed Central

    Yang, Kai; Jiang, Xuejun; Cheng, Shuqun; Chen, Chengzhi; Cao, Xianqing; Tu, Baijie

    2016-01-01

    Objective: To evaluate the effects of occupational exposures to coke oven emissions (COEs) and benzo[a]pyrene (B[a]P) on the prevalence of hypertension and abnormal electrocardiogram (ECG) in coke oven workers. Methods: We included 880 coke oven workers and 710 oxygen employees in the exposed and control groups, respectively. Blood pressure (BP), ECG, blood lipid levels, and glucose levels of all subjects were measured. COE and B[a]P concentrations at the bottom, side, and top of the oven and control plants were estimated by weighing and high-performance liquid chromatography. Results: The COE concentration at the top and side was higher than that at the bottom (P < 0.05). The levels of B[a]P at the top and side significantly exceeded the limit value. Abnormal BP, ECG, the detection ratio of hypertension and left ventricular high voltage were significantly greater in the exposed group than in the control group (P < 0.05). The logistic regression analysis results revealed that age and B[a]P exposure were risk factors for hypertension in coke oven workers (P < 0.05) and both were risk factors for abnormal ECG (P < 0.05). Moreover, B[a]P exposure, age, and gender were risk factors for impaired fasting glucose in coke oven workers (P < 0.05). Conclusions: B[a]P and COE exposures are risk factors for hypertension and abnormal ECG in coke oven workers. PMID:27885241

  17. Effect of short LED lamp exposure on wear resistance, residual monomer and degree of conversion for Filtek Z250 and Tetric EvoCeram composites.

    PubMed

    Kopperud, Hilde M; Johnsen, Gaute F; Lamolle, Sébastien; Kleven, Inger S; Wellendorf, Hanne; Haugen, Håvard J

    2013-08-01

    The latest LED dental curing devices claim sufficient curing of restorative materials with short curing times. This study evaluates mechanical and chemical properties as a function of curing time of two commercial composite filling materials cured with three different LED lamps. The composites were Filtek Z250 (3M ESPE) and Tetric EvoCeram (Ivoclar Vivadent) and the LED curing devices were bluephase 16i (Ivoclar Vivadent), L.E.Demetron II (Kerr) and Mini L.E.D. (Satelec). Control samples were cured with a QTH-lamp (VCL 400, Kerr). The wear resistance after simulated tooth brushing, degree of conversion, curing depth, and amounts of residual monomers were measured after different curing times. The results of this study show that short curing time with high-intensity LEDs may influence the bulk properties of the materials, resulting in lower curing depth and increased residual monomer content. The measured surface properties of the materials, degree of conversion and wear resistance, were not affected by short curing times to the same extent. This study demonstrates that reduced exposure time with high intensity LEDs can result in composite restorations with inferior curing depth and increased leaching of monomers. Dentists are recommended to use sufficient curing times even with high intensity LEDs to ensure adequate curing and minimize the risk of monomer leaching. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  18. 40 CFR 745.233 - Lead-based paint activities requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Lead-based paint activities...

  19. 25. DETAIL OF INSCRIPTION ON BAKE OVEN WHICH READS: PREMIUM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    25. DETAIL OF INSCRIPTION ON BAKE OVEN WHICH READS: PREMIUM PATENT BAKE OVEN ROASTER BY ALFRED H. REIP NO. 337 BALT. STREET BALTIMORE - Hazelwood, 18611 Queen Anne Road, Upper Marlboro, Prince George's County, MD

  20. SU-E-T-112: Experimental Characterization of a Novel Thermal Reservoir for Consistent and Accurate Annealing of High-Sensitivity TLDs.

    PubMed

    Donahue, W; Bongiorni, P; Hearn, R; Rodgers, J; Nath, R; Chen, Z

    2012-06-01

    To develop and characterize a novel thermal reservoir for consistent and accurate annealing of high-sensitivity thermoluminescence dosimeters (TLD-100H) for dosimetry of brachytherapy sources. The sensitivity of TLD-100H is about 18 times that of TLD-100 which has clear advantages in for interstitial brachytherapy sources. However, the TLD-100H requires a short high temperature annealing cycle (15 min.) and opening and closing the oven door causes significant temperature fluctuations leading to unreliable measurements. A new thermal reservoir made of aluminum alloy was developed to provide stable temperature environment in a standard hot air oven. The thermal reservoir consisted of a 20 cm × 20 cm × 8 cm Al block with a machine-milled chamber in the middle to house the aluminum TLD holding tray. The thermal reservoir was placed inside the oven until it reaches thermal equilibrium with oven chamber. The temperatures of the oven chamber, heat reservoir, and TLD holding tray were monitored by two independent thermo-couples which interfaced digitally to a control computer. A LabView interface was written for monitoring and recording the temperatures in TLD holding tray, the thermal reservoir, and oven chamber. The temperature profiles were measured as a function of oven-door open duration. The settings for oven chamber temperature and oven door open-close duration were optimized to achieve a stable temperature of 240 0C in the TLD holding tray. Complete temperature profiles of the TLD annealing tray over the entire annealing process were obtained. A LabView interface was written for monitoring and recording the temperatures in TLD holding The use of the thermal reservoir has significantly reduced the temperature fluctuations caused by the opening of oven door when inserting the TLD holding tray into the oven chamber. It has enabled consistent annealing of high-sensitivity TLDs. A comprehensive characterization of a custom-built novel thermal reservoir for annealing high-sensitivity TLD has been carried out. It enabled consistent and accurate annealing of high- sensitivity TLDs which could significantly improve the efficiency of brachytherapy source characterizations. Supported in part by NIH grant R01-CA134627. © 2012 American Association of Physicists in Medicine.

  1. Cold-Curing Structural Epoxy Resins: Analysis of the Curing Reaction as a Function of Curing Time and Thickness

    PubMed Central

    Esposito Corcione, Carola; Freuli, Fabrizio; Frigione, Mariaenrica

    2014-01-01

    The curing reaction of a commercial cold-curing structural epoxy resin, specifically formulated for civil engineering applications, was analyzed by thermal analysis as a function of the curing time and the sample thickness. Original and remarkable results regarding the effects of curing time on the glass transition temperature and on the residual heat of reaction of the cold-cured epoxy were obtained. The influence of the sample thickness on the curing reaction of the cold-cured resin was also deeply investigated. A highly exothermal reaction, based on a self-activated frontal polymerization reaction, was supposed and verified trough a suitable temperature signal acquisition system, specifically realized for this measurement. This is one of the first studies carried out on the curing behavior of these peculiar cold-cured epoxy resins as a function of curing time and thickness. PMID:28788215

  2. [Cohort study of effects on lung function of coke oven workers exposured to coke oven emissions].

    PubMed

    Zhi, Yongfen; Zhang, Hongming; Li, Weixing; Hu, Zhipeng; Liu, Weihua; Li, Yangfan; Zheng, Jinpin

    2015-07-01

    Through comparative study on pulmonary function damage of coke oven workers exposed to coke oven emissions with the same group before and after five years, and further explore the relationship between the coke oven emissions and injury in pulmonary function of coke oven worker. Select a coking plant in Shanxi 165 coke oven workers (exposed group) and 52 auxiliary workers (control group) for the study, using a uniform questionnaire to collect workers' personal information. Fixed workplace air samples collected periodically. Air samples of benzo (a) pyrene concentrations was measured by high pressure liquid chromatograph. Pulmonary function of research object was measured by portable spirometer respectively in 2009 and 2013, and comparative analysis on it. The concentration of B(a)P was no significant difference in the same area between 5 years in 2009-2013. Compared with 2009, 2013 control workers lung function index and the abnormal rate had no significant difference (P > 0.05). But FVC%, FEV1.0%, MVV%, VC% and FEF25% of exposed workers in 2013 was significantly lower than in 2009, FVC%, FEV1.0%, VC% and FEF25% pulmonary dysfunction rate in 2013 was also significantly higher than in 2009, difference was statistically significant (P < 0.05). Workers emerging pulmonary function abnormalities mainly distributed in furnace roof and side. furnace roof group FVC%, FEV1.0%, VC% additional abnormal number (rate) was significantly higher than furnace floor and the control group (P < 0.05), and furnace side groop was significantly higher than the control group, the difference was statistically significant (P < 0.05). Multivariate Logistic regression analysis showed that after 5 years FVC%, FEV1% and VC% of abnormal lung function emerging adjusted OR of furnace roof workers were 7.939, 5.966 and 4.956. For abnormal of FVC%, FEV1%, VC% and MVV%, the contacting coke seniority is a risk factor. There is a positive interaction between contacting coke seniority and furnace roof (P < 0.05). Coke oven workers lung function damage associated with exposureing to coke oven emissions, coke oven emissions exposure level and exposure time are the main factors of coke oven workers in lung function damage, there is a positive interaction between the two factors.

  3. 7 CFR 58.412 - Coolers or curing rooms.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Coolers or curing rooms. 58.412 Section 58.412....412 Coolers or curing rooms. Coolers or curing rooms where cheese is held for curing or storage shall... times. The shelves shall be kept clean and dry. This does not preclude the maintenance of suitable...

  4. 7 CFR 58.412 - Coolers or curing rooms.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Coolers or curing rooms. 58.412 Section 58.412....412 Coolers or curing rooms. Coolers or curing rooms where cheese is held for curing or storage shall... times. The shelves shall be kept clean and dry. This does not preclude the maintenance of suitable...

  5. Feasibility study analysis for multi-function dual energy oven (case study: tapioca crackers small medium enterprise)

    NASA Astrophysics Data System (ADS)

    Soraya, N. W.; El Hadi, R. M.; Chumaidiyah, E.; Tripiawan, W.

    2017-12-01

    Conventional drying process is constrained by weather (cloudy / rainy), and requires wide drying area, and provides low-quality product. Multi-function dual energy oven is the appropriate technology to solve these problems. The oven uses solar thermal or gas heat for drying various type of products, including tapioca crackers. Investment analysis in technical, operational, and financial aspects show that the multi-function dual energy oven is feasible to be implemented for small medium enterprise (SME) processing tapioca crackers.

  6. Light curing through glass ceramics with a second- and a third-generation LED curing unit: effect of curing mode on the degree of conversion of dual-curing resin cements.

    PubMed

    Flury, Simon; Lussi, Adrian; Hickel, Reinhard; Ilie, Nicoleta

    2013-12-01

    The aim of this study was to measure the degree of conversion (DC) of five dual-curing resin cements after different curing modes with a second- and a third-generation light-emitting diode (LED) curing unit. Additionally, irradiance of both light curing units was measured at increasing distances and through discs of two glass ceramics for computer-aided design/manufacturing (CAD/CAM). Irradiance and spectra of the Elipar FreeLight 2 (Standard Mode (SM)) and of the VALO light curing unit (High Power Mode (HPM) and Xtra Power Mode (XPM)) were measured with a MARC radiometer. Irradiance was measured at increasing distances (control) and through discs (1.5 to 6 mm thickness) of IPS Empress CAD and IPS e.max CAD. DC of Panavia F2.0, RelyX Unicem 2 Automix, SpeedCEM, BisCem, and BeautiCem SA was measured with an attenuated total reflectance-Fourier transform infrared spectrometer when self-cured (negative control) or light cured in SM for 40 s, HPM for 32 s, or XPM for 18 s. Light curing was performed directly (positive control) or through discs of either 1.5- or 3-mm thickness of IPS Empress CAD or IPS e.max CAD. DC was analysed with Kruskal-Wallis tests followed by pairwise Wilcoxon rank sum tests (α = 0.05). Maximum irradiances were 1,545 mW/cm(2) (SM), 2,179 mW/cm(2) (HPM), and 4,156 mW/cm(2) (XPM), and all irradiances decreased by >80 % through discs of 1.5 mm, ≥95 % through 3 mm, and up to >99 % through 6 mm. Generally, self-curing resulted in the lowest DC. For some cements, direct light curing did not result in higher DC compared to when light cured through ceramic discs. For other cements, light curing through ceramic discs of 3 mm generally reduced DC. Light curing was favourable for dual-curing cements. Some cements were more susceptible to variations in curing mode than others. When light curing a given cement, the higher irradiances of the third-generation LED curing unit resulted in similar DC compared to the second-generation one, though at shorter light curing times.

  7. 40 CFR 63.301 - Definitions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Coke... implement the provisions of this subpart or its designated agent). Brownfield coke oven battery means a new coke oven battery that replaces an existing coke oven battery or batteries with no increase in the...

  8. 22. VIEW OF A SINGLE BEEHIVE COKE OVEN SHOWING THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    22. VIEW OF A SINGLE BEEHIVE COKE OVEN SHOWING THE INTERIOR STRUCTURE OF THE OVEN. - Tower Hill No. 2 Mine, Approximately 0.47 mile Southwest of intersection of Stone Church Road & Township Route 561, Hibbs, Fayette County, PA

  9. Effect of oven cooking method on formation of heterocyclic amines and quality characteristics of chicken patties: steam-assisted hybrid oven versus convection ovens.

    PubMed

    Isleroglu, Hilal; Kemerli, Tansel; Özdestan, Özgül; Uren, Ali; Kaymak-Ertekin, Figen

    2014-09-01

    The aim of this study was to evaluate effect of steam-assisted hybrid oven cooking method in comparison with convection ovens (natural and forced) on quality characteristics (color, hardness, cooking loss, soluble protein content, fat retention, and formation of heterocyclic aromatic amines) of chicken patties. The cooking experiments of chicken patties (n = 648) were conducted at oven temperatures of 180, 210, and 240°C until 3 different end point temperatures (75, 90, and 100°C) were reached. Steam-assisted hybrid oven cooking enabled faster cooking than convection ovens and resulted in chicken patties having lower a* and higher L* value, lower hardness, lower fat, and soluble protein content (P < 0.05), and higher cooking loss than convection ovens. Steam-assisted hybrid oven could reduce the formation of heterocyclic aromatic amines that have mutagenic and carcinogenic effects on humans. © 2014 Poultry Science Association Inc.

  10. 40 CFR 63.301 - Definitions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Coke... implement the provisions of this subpart or its designated agent). Brownfield coke oven battery means a new coke oven battery that replaces an existing coke oven battery or batteries with no increase in the...

  11. 40 CFR 63.301 - Definitions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Coke... implement the provisions of this subpart or its designated agent). Brownfield coke oven battery means a new coke oven battery that replaces an existing coke oven battery or batteries with no increase in the...

  12. 40 CFR 63.301 - Definitions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES National Emission Standards for Coke... implement the provisions of this subpart or its designated agent). Brownfield coke oven battery means a new coke oven battery that replaces an existing coke oven battery or batteries with no increase in the...

  13. Ultraviolet (UV)-reflective paint with ultraviolet germicidal irradiation (UVGI) improves decontamination of nosocomial bacteria on hospital room surfaces.

    PubMed

    Jelden, Katelyn C; Gibbs, Shawn G; Smith, Philip W; Hewlett, Angela L; Iwen, Peter C; Schmid, Kendra K; Lowe, John J

    2017-06-01

    An ultraviolet germicidal irradiation (UVGI) generator (the TORCH, ClorDiSys Solutions, Inc.) was used to compare the disinfection of surface coupons (plastic from a bedrail, stainless steel, and chrome-plated light switch cover) in a hospital room with walls coated with ultraviolet (UV)-reflective paint (Lumacept) or standard paint. Each surface coupon was inoculated with methicillin-resistant Staphylococcus aureus (MRSA) or vancomycin-resistant Enterococcus faecalis (VRE), placed at 6 different sites within a hospital room coated with UV-reflective paint or standard paint, and treated by 10 min UVC exposure (UVC dose of 0-688 mJ/cm 2 between sites with standard paint and 0-553 mJ/cm 2 with UV-reflective paint) in 8 total trials. Aggregated MRSA concentrations on plastic bedrail surface coupons were reduced on average by 3.0 log 10 (1.8 log 10 Geometric Standard Deviation [GSD]) with standard paint and 4.3 log 10 (1.3 log 10 GSD) with UV-reflective paint (p = 0.0005) with no significant reduction differences between paints on stainless steel and chrome. Average VRE concentrations were reduced by ≥4.9 log 10 (<1.2 log 10 GSD) on all surface types with UV-reflective paint and ≤4.1 log 10 (<1.7 log 10 GSD) with standard paint (p < 0.05). At 5 aggregated sites directly exposed to UVC light, MRSA concentrations on average were reduced by 5.2 log 10 (1.4 log 10 GSD) with standard paint and 5.1 log 10 (1.2 log 10 GSD) with UV-reflective paint (p = 0.017) and VRE by 4.4 log 10 (1.4 log 10 GSD) with standard paint and 5.3 log 10 (1.1 log 10 GSD) with UV-reflective paint (p < 0.0001). At one indirectly exposed site on the opposite side of the hospital bed from the UVGI generator, MRSA concentrations on average were reduced by 1.3 log 10 (1.7 log 10 GSD) with standard paint and 4.7 log 10 (1.3 log 10 GSD) with UV-reflective paint (p < 0.0001) and VRE by 1.2 log 10 (1.5 log 10 GSD) with standard paint and 4.6 log 10 (1.1 log 10 GSD) with UV-reflective paint (p < 0.0001). Coating hospital room walls with UV-reflective paint enhanced UVGI disinfection of nosocomial bacteria on various surfaces compared to standard paint, particularly at a surface placement site indirectly exposed to UVC light.

  14. Analysis of curing of a sustained release coating formulation by application of NIR spectroscopy to monitor changes associated with glyceryl monostearate.

    PubMed

    Howland, Harris; Fahmy, Raafat; Hoag, Stephen W

    2015-01-01

    For controlled release, latex or pseudolatex coatings to function as designed, it must be cured at temperatures at or slightly above the polymer's glass transition temperature. The focus of this study is to develop an understanding of the curing process and to develop near infrared spectroscopy as a tool for monitoring curing. Differential scanning calorimetry studies were used to determine how the thermal properties of glyceryl monostearate (GMS) and its polymorphic forms relate to the extent of Eudragit® polymer coat curing at different curing temperatures. The different GMS melting endotherms were used to monitor the extent of curing and as references for model development. The calculated melting peak areas for the GMS were plotted versus time and found to be dependent on time and temperature used for curing. Principal component analysis and parallel factor analysis were used to investigate the effect of curing on the films and showed that spectral changes could be could be directly related to the changes associated with the GMS during curing. Partial least square models developed could predict the extent of curing and the final state of GMS post curing.

  15. Effect of curing condition on the concrete moisture retention and its shielding implication for the design of fusion facilities

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Huang, S.; Chang, J.; Amin, S.

    1981-01-01

    Teste were conducted to determine the moisture retention for the 0.5 wt% borated concrete under three curing conditions. The three curing conditions are (1) curing at 100% relative humidity for a 28-day period at 21/degree/C, (2) curing at 100% relative humidity for a 7-day period, then at air-dry 50% relative humidity for the remaining 28-day curing period at 21/degree/C, and (3) curing at 100% relative humidity for a period of 7 days and then curing at air-dry 20% relative humidity for the remaining curing period at 21/degree/C. The concrete shielding curves are presented for several mositure contents. The results shouldmore » be helpful to assist the design of a cost effective concrete shield for fusion facilities.« less

  16. Effect of silica fume on the fresh and hardened properties of fly ash-based self-compacting geopolymer concrete

    NASA Astrophysics Data System (ADS)

    Memon, Fareed Ahmed; Nuruddin, Muhd Fadhil; Shafiq, Nasir

    2013-02-01

    The effect of silica fume on the fresh and hardened properties of fly ash-based self-compacting geopolymer concrete (SCGC) was investigated in this paper. The work focused on the concrete mixes with a fixed water-to-geopolymer solid (W/Gs) ratio of 0.33 by mass and a constant total binder content of 400 kg/m3. The mass fractions of silica fume that replaced fly ash in this research were 0wt%, 5wt%, 10wt%, and 15wt%. The workability-related fresh properties of SCGC were assessed through slump flow, V-funnel, and L-box test methods. Hardened concrete tests were limited to compressive, splitting tensile and flexural strengths, all of which were measured at the age of 1, 7, and 28 d after 48-h oven curing. The results indicate that the addition of silica fume as a partial replacement of fly ash results in the loss of workability; nevertheless, the mechanical properties of hardened SCGC are significantly improved by incorporating silica fume, especially up to 10wt%. Applying this percentage of silica fume results in 4.3% reduction in the slump flow; however, it increases the compressive strength by 6.9%, tensile strength by 12.8% and flexural strength by 11.5%.

  17. Self-regenerating and hybrid irreversible/reversible PDMS microfluidic devices

    PubMed Central

    Shiroma, Letícia S.; Piazzetta, Maria H. O.; Duarte-Junior, Gerson F.; Coltro, Wendell K. T.; Carrilho, Emanuel; Gobbi, Angelo L.; Lima, Renato S.

    2016-01-01

    This paper outlines a straightforward, fast, and low-cost method to fabricate polydimethylsiloxane (PDMS) chips. Termed sandwich bonding (SWB), this method requires only a laboratory oven. Initially, SWB relies on the reversible bonding of a coverslip over PDMS channels. The coverslip is smaller than the substrate, leaving a border around the substrate exposed. Subsequently, a liquid composed of PDMS monomers and a curing agent is poured onto the structure. Finally, the cover is cured. We focused on PDMS/glass chips because of their key advantages in microfluidics. Despite its simplicity, this method created high-performance microfluidic channels. Such structures featured self-regeneration after leakages and hybrid irreversible/reversible behavior. The reversible nature was achieved by removing the cover of PDMS with acetone. Thus, the PDMS substrate and glass coverslip could be detached for reuse. These abilities are essential in the stages of research and development. Additionally, SWB avoids the use of surface oxidation, half-cured PDMS as an adhesive, and surface chemical modification. As a consequence, SWB allows surface modifications before the bonding, a long time for alignment, the enclosure of sub-micron channels, and the prototyping of hybrid devices. Here, the technique was successfully applied to bond PDMS to Au and Al. PMID:27181918

  18. 40 CFR 86.317-79 - Hydrocarbon analyzer specifications.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... flame ionization detector (HFID) analyzer. (b) Option. A non-heated flame ionization detector (FID) that... temperature oven housing the detector and sample-handling components. It shall maintain temperature with 2 °C of the set point. The detector, oven, and sample-handling components within the oven shall be...

  19. 21. VIEW OF A SINGLE BEEHIVE COKE OVEN. THE USE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    21. VIEW OF A SINGLE BEEHIVE COKE OVEN. THE USE OF BRICK AND STONE TO FACE THE OVEN WAS A TYPICAL CONSTRUCTION TECHNIQUE. - Tower Hill No. 2 Mine, Approximately 0.47 mile Southwest of intersection of Stone Church Road & Township Route 561, Hibbs, Fayette County, PA

  20. 40 CFR 63.309 - Performance tests and procedures.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Standards for Coke Oven Batteries § 63.309 Performance tests and procedures. (a) Except as otherwise... coke oven battery, the results of which shall be used in accordance with procedures specified in this subpart to determine compliance with each of the applicable visible emission limitations for coke oven...

  1. 40 CFR 63.309 - Performance tests and procedures.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Standards for Coke Oven Batteries § 63.309 Performance tests and procedures. (a) Except as otherwise... coke oven battery, the results of which shall be used in accordance with procedures specified in this subpart to determine compliance with each of the applicable visible emission limitations for coke oven...

  2. 40 CFR 63.313 - Implementation and enforcement.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Standards for Coke Oven Batteries § 63.313 Implementation and enforcement. (a) This subpart can be... shall notify the coke oven battery owner or operator that inspections and performance tests shall be... Administrator shall give the coke oven battery owner or operator at least 15 days notice that implementation...

  3. A review on paint sludge from automotive industries: Generation, characteristics and management.

    PubMed

    Salihoglu, Guray; Salihoglu, Nezih Kamil

    2016-03-15

    The automotive manufacturing process results in the consumption of several natural sources and the generation of various types of wastes. The primary source of hazardous wastes at an automotive manufacturing plant is the painting process, and the major waste fraction is paint sludge, which is classified with EU waste code of 080113* implying hazardous characteristics. The amount of the paint sludge generated increases every year with the worldwide increase in the car production. The characteristics of the paint sludge, which mainly designate the management route, are mainly determined by the type of the paint used, application technique employed, and the chemicals applied such as flocculants, detackifiers, pH boosters, antifoam agents, and biocides as well as the dewatering techniques preferred. Major routes for the disposal of the paint sludges are incineration as hazardous waste or combustion at cement kilns. Because of high dissolved organic carbon content of the paint, the paint sludge cannot be accepted by landfills according to European Union Legislations. More investigations are needed in the field of paint sludge recycling such as recycling it as a new paint or as other formulations, or making use of the sludge for the production of construction materials. Research on the applicability of the paint sludge in composting and biogasification can also be useful. Ongoing research is currently being conducted on new application techniques to increase the effectiveness of paint transfer, which helps to prevent the generation of paint sludge. Advancements in paint and coating chemistry such as the reduction in the coating layers with its thickness also help to decrease the level of paint sludge generation. Investigations on the effects of the chemicals on the recycling potential of paint sludges and consideration of these effects by the chemical manufacturer companies would be extremely important. This review presents the formation of paint sludge, the factors affecting its characteristics, common disposal routes, the findings of the field trips to automotive manufacturing plants in Turkey, and a summary of the characterization findings of the paint sludge samples from a plant in Turkey. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. 16. 110 SANSOM STREET, OBLIQUE VIEW OF BAKE OVEN IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. 110 SANSOM STREET, OBLIQUE VIEW OF BAKE OVEN IN CELLAR (Note the double arch in front of the oven. The front arch supported the structural framing.) - James McCrea Houses, 108-110 Sansom Street, Philadelphia, Philadelphia County, PA

  5. Self-regenerating and hybrid irreversible/reversible PDMS microfluidic devices.

    PubMed

    Shiroma, Letícia S; Piazzetta, Maria H O; Duarte-Junior, Gerson F; Coltro, Wendell K T; Carrilho, Emanuel; Gobbi, Angelo L; Lima, Renato S

    2016-05-16

    This paper outlines a straightforward, fast, and low-cost method to fabricate polydimethylsiloxane (PDMS) chips. Termed sandwich bonding (SWB), this method requires only a laboratory oven. Initially, SWB relies on the reversible bonding of a coverslip over PDMS channels. The coverslip is smaller than the substrate, leaving a border around the substrate exposed. Subsequently, a liquid composed of PDMS monomers and a curing agent is poured onto the structure. Finally, the cover is cured. We focused on PDMS/glass chips because of their key advantages in microfluidics. Despite its simplicity, this method created high-performance microfluidic channels. Such structures featured self-regeneration after leakages and hybrid irreversible/reversible behavior. The reversible nature was achieved by removing the cover of PDMS with acetone. Thus, the PDMS substrate and glass coverslip could be detached for reuse. These abilities are essential in the stages of research and development. Additionally, SWB avoids the use of surface oxidation, half-cured PDMS as an adhesive, and surface chemical modification. As a consequence, SWB allows surface modifications before the bonding, a long time for alignment, the enclosure of sub-micron channels, and the prototyping of hybrid devices. Here, the technique was successfully applied to bond PDMS to Au and Al.

  6. 40 CFR 86.317-79 - Hydrocarbon analyzer specifications.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... flame ionization detector (HFID) analyzer. (b) Option. A non-heated flame ionization detector (FID) that... temperature oven housing the detector and sample-handling components. It shall maintain temperature with 2 °C of the set point. The detector, oven, and sample-handling components within the oven shall be...

  7. 40 CFR 63.306 - Work practice standards.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Standards for Coke Oven Batteries § 63.306 Work practice standards. (a) Work practice plan. On or before... plan for each coke oven battery. The plan shall be designed to achieve compliance with visible emission limitations for coke oven doors, topside port lids, offtake systems, and charging operations under this...

  8. 40 CFR 63.310 - Requirements for startups, shutdowns, and malfunctions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... CATEGORIES National Emission Standards for Coke Oven Batteries § 63.310 Requirements for startups, shutdowns... or operator shall operate and maintain the coke oven battery and its pollution control equipment... operator of a coke oven battery shall develop, according to paragraph (c) of this section, a written...

  9. 40 CFR 63.313 - Implementation and enforcement.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Standards for Coke Oven Batteries § 63.313 Implementation and enforcement. (a) This subpart can be... shall notify the coke oven battery owner or operator that inspections and performance tests shall be... Administrator shall give the coke oven battery owner or operator at least 15 days notice that implementation...

  10. 40 CFR 63.306 - Work practice standards.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Standards for Coke Oven Batteries § 63.306 Work practice standards. (a) Work practice plan. On or before... plan for each coke oven battery. The plan shall be designed to achieve compliance with visible emission limitations for coke oven doors, topside port lids, offtake systems, and charging operations under this...

  11. 40 CFR 63.313 - Implementation and enforcement.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Standards for Coke Oven Batteries § 63.313 Implementation and enforcement. (a) This subpart can be... shall notify the coke oven battery owner or operator that inspections and performance tests shall be... Administrator shall give the coke oven battery owner or operator at least 15 days notice that implementation...

  12. Influence of electrical and hybrid heating on bread quality during baking.

    PubMed

    Chhanwal, N; Ezhilarasi, P N; Indrani, D; Anandharamakrishnan, C

    2015-07-01

    Energy efficiency and product quality are the key factors for any food processing industry. The aim of the study was to develop energy and time efficient baking process. The hybrid heating (Infrared + Electrical) oven was designed and fabricated using two infrared lamps and electric heating coils. The developed oven can be operated in serial or combined heating modes. The standardized baking conditions were 18 min at 220°C to produce the bread from hybrid heating oven. Effect of baking with hybrid heating mode (H-1 and H-2, hybrid oven) on the quality characteristics of bread as against conventional heating mode (C-1, pilot scale oven; C-2, hybrid oven) was studied. The results showed that breads baked in hybrid heating mode (H-2) had higher moisture content (28.87%), higher volume (670 cm(3)), lower crumb firmness value (374.6 g), and overall quality score (67.0) comparable to conventional baking process (68.5). Moreover, bread baked in hybrid heating mode showed 28% reduction in baking time.

  13. 24 CFR 200.800 - Lead-based paint.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 2 2014-04-01 2014-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  14. 24 CFR 598.408 - Lead-based paint requirements.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 3 2014-04-01 2013-04-01 true Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

  15. 40 CFR 745.230 - Work practice standards for conducting lead-based paint activities: public and commercial...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.230 Work practice standards for conducting lead-based paint activities: public... lead-based paint activities: public and commercial buildings, bridges and superstructures. [Reserved...

  16. 7 CFR 58.412 - Coolers or curing rooms.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Coolers or curing rooms. 58.412 Section 58.412....412 Coolers or curing rooms. Coolers or curing rooms where cheese is held for curing or storage shall... times. The shelves shall be kept clean and dry. This does not preclude the maintenance of suitable...

  17. [The dose response decrease of lung function associated with the urinary polycyclic aromatic hydrocarbons metabolites in coke oven workers].

    PubMed

    Hu, Die; Deng, Qi-fei; Huang, Su-li; He, Yun-feng; Guo, Huan; Wu, Tang-chun

    2012-12-01

    To analyze the relationship between metabolites of polycyclic aromatic hydrocarbons (PAHs) and lung function in coke oven workers, and to provide scientific basis for further exploring the potential mechanism and developing the preventing strategies of the workers' early lung damage. We measured carbon monoxide, sulfur dioxide, benzene soluble matter, particulate matters, and PAHs at different workplaces of a coke oven plant. Detailed information on demography and occupational health condition of 912 workers were collected. We divided these workers into control group and coke oven group according to their workplaces and the different concentrations of COEs in the environment. We detected 10 urinary PAH metabolites and lung function using gas chromatography-mass spectrometry and spirometric tests, respectively. FEV(1.0) (91.12 ± 13.31) and FEV(1.0)/FVC (108.61 ± 20.37) of the coke oven group is significantly lower than the control group (94.16 ± 15.57, 113.45 ± 19.70). In the coke oven group, the hydroxyphenanthrene and 1-hydroxypyrene are negatively correlated with FEV(1.0)/FVC (β = -0.136, β = -0.100), Ptrend < 0.05 for all. The dose response decrease of lung function is associated with the urinary PAH metabolites in coke oven workers. Indicated that the long exposure to PAHs may cause the early lung damage in coke oven workers, phenanthrene and pyrene may be the main factors.

  18. 40 CFR 63.307 - Standards for bypass/bleeder stacks.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Standards for Coke Oven Batteries § 63.307 Standards for bypass/bleeder stacks. (a)(1) Except as otherwise... flow generated by the battery, which shall thereafter be operated and maintained. (2) Coke oven... operator of a brownfield coke oven battery or a padup rebuild shall install such a flare system before...

  19. 40 CFR 63.307 - Standards for bypass/bleeder stacks.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.307 Standards for bypass/bleeder stacks. (a)(1.... (2) Coke oven emissions shall not be vented to the atmosphere through bypass/bleeder stacks, except.... (3) The owner or operator of a brownfield coke oven battery or a padup rebuild shall install such a...

  20. 40 CFR 63.312 - Existing regulations and requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.312 Existing regulations and requirements. (a) The..., topside port lids, coke oven doors, and charging operations in effect on September 15, 1992, or which have... method of monitoring in effect on September 15, 1992, and that ensures coke oven emission reductions...

  1. 40 CFR 63.307 - Standards for bypass/bleeder stacks.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.307 Standards for bypass/bleeder stacks. (a)(1.... (2) Coke oven emissions shall not be vented to the atmosphere through bypass/bleeder stacks, except.... (3) The owner or operator of a brownfield coke oven battery or a padup rebuild shall install such a...

  2. 40 CFR 63.300 - Applicability.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., the provisions of this subpart apply to existing by-product coke oven batteries at a coke plant and to..., 1995, for existing by-product coke oven batteries subject to emission limitations in § 63.302(a)(1) or..., 2003, for existing by-product coke oven batteries subject to emission limitations in § 63.302(a)(2); (3...

  3. 24 CFR 574.635 - Lead-based paint.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

  4. 24 CFR 511.15 - Lead-based paint.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Lead-based paint. 511.15 Section... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

  5. 24 CFR 511.15 - Lead-based paint.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 3 2014-04-01 2013-04-01 true Lead-based paint. 511.15 Section 511... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

  6. 24 CFR 574.635 - Lead-based paint.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 3 2014-04-01 2013-04-01 true Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

  7. 40 CFR 745.110 - Opportunity to conduct an evaluation.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential Property § 745... presence of lead-based paint and/or lead-based paint hazards. (b) Not withstanding paragraph (a) of this...

  8. 40 CFR 745.110 - Opportunity to conduct an evaluation.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential Property § 745... presence of lead-based paint and/or lead-based paint hazards. (b) Not withstanding paragraph (a) of this...

  9. 40 CFR 60.391 - Definitions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

  10. 40 CFR 63.307 - Standards for bypass/bleeder stacks.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.307 Standards for bypass/bleeder stacks. (a)(1.... (2) Coke oven emissions shall not be vented to the atmosphere through bypass/bleeder stacks, except.... (3) The owner or operator of a brownfield coke oven battery or a padup rebuild shall install such a...

  11. 40 CFR 60.391 - Definitions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

  12. 40 CFR 63.307 - Standards for bypass/bleeder stacks.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Standards for Coke Oven Batteries § 63.307 Standards for bypass/bleeder stacks. (a)(1) Except as otherwise... flow generated by the battery, which shall thereafter be operated and maintained. (2) Coke oven... operator of a brownfield coke oven battery or a padup rebuild shall install such a flare system before...

  13. 40 CFR 63.312 - Existing regulations and requirements.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.312 Existing regulations and requirements. (a) The..., topside port lids, coke oven doors, and charging operations in effect on September 15, 1992, or which have... method of monitoring in effect on September 15, 1992, and that ensures coke oven emission reductions...

  14. 40 CFR 63.312 - Existing regulations and requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.312 Existing regulations and requirements. (a) The..., topside port lids, coke oven doors, and charging operations in effect on September 15, 1992, or which have... method of monitoring in effect on September 15, 1992, and that ensures coke oven emission reductions...

  15. 40 CFR 63.312 - Existing regulations and requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.312 Existing regulations and requirements. (a) The..., topside port lids, coke oven doors, and charging operations in effect on September 15, 1992, or which have... method of monitoring in effect on September 15, 1992, and that ensures coke oven emission reductions...

  16. 7 CFR 58.412 - Coolers or curing rooms.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Coolers or curing rooms. 58.412 Section 58.412....412 Coolers or curing rooms. Coolers or curing rooms where cheese is held for curing or storage shall... times. The shelves shall be kept clean and dry. This does not preclude the maintenance of suitable...

  17. 24 CFR 200.800 - Lead-based paint.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 2 2011-04-01 2011-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  18. 24 CFR 598.408 - Lead-based paint requirements.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

  19. 24 CFR 598.408 - Lead-based paint requirements.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 3 2012-04-01 2012-04-01 false Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

  20. 24 CFR 200.800 - Lead-based paint.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 2 2013-04-01 2013-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  1. 24 CFR 598.408 - Lead-based paint requirements.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

  2. 24 CFR 965.701 - Lead-based paint poisoning prevention.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Lead-based paint poisoning...

  3. 24 CFR 965.701 - Lead-based paint poisoning prevention.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2013-04-01 2013-04-01 false Lead-based paint poisoning...

  4. 24 CFR 965.701 - Lead-based paint poisoning prevention.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Lead-based paint poisoning...

  5. 7 CFR 58.412 - Coolers or curing rooms.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Coolers or curing rooms. 58.412 Section 58.412....412 Coolers or curing rooms. Coolers or curing rooms where cheese is held for curing or storage shall... times. The shelves shall be kept clean and dry. This does not preclude the maintenance of suitable...

  6. Building a Low Cost Solar Oven: An Opportunity to Teach Thermodynamics

    NASA Astrophysics Data System (ADS)

    Nogueira, Ana

    2014-03-01

    We suggested building a solar oven using cardboard boxes, glass wool and metal plate as part of a school project permeated by the discussion of physical concepts. The main topics addressed are from the heat and thermodynamics areas, and for these themes we followed the standard books used in high school. We can work in a practical manner with the thermometer, along with the concept of temperature, measuring the temperature of the oven when cooking. To discuss how the oven works, we introduce the concept of heat as an energy flow of a body with a higher temperature to one with lower temperature. Threads as heat capacity and specific heat of a substance are introduced, also discussing the use of glass wool, which function is to prevent heat exchange from the oven's interior with the environment. It is possible to demonstrate the three forms of heat transfer using the solar oven, and how the greenhouse effect is harnessed. One can discuss topics such as electromagnetic radiation, black-body radiation and the Stefan-Boltzmann law. We surveyed the response curve of our oven and an estimate of its total solar energy absorption efficiency. The development of this project allows a good understanding of the operation principles of a solar oven. UNIMONTES.

  7. 24 CFR 1003.607 - Lead-based paint.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

  8. 24 CFR 574.635 - Lead-based paint.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

  9. 24 CFR 1003.607 - Lead-based paint.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

  10. 24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

  11. 24 CFR 35.135 - Use of paint containing lead.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Use of paint containing lead. 35...

  12. 40 CFR 745.110 - Opportunity to conduct an evaluation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential Property § 745... presence of lead-based paint and/or lead-based paint hazards. (b) Not withstanding paragraph (a) of this...

  13. 24 CFR 35.135 - Use of paint containing lead.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Use of paint containing lead. 35...

  14. 40 CFR 745.110 - Opportunity to conduct an evaluation.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential Property § 745... presence of lead-based paint and/or lead-based paint hazards. (b) Not withstanding paragraph (a) of this...

  15. 24 CFR 35.135 - Use of paint containing lead.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Use of paint containing lead. 35...

  16. 24 CFR 35.98 - Impact on State and local requirements.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential... regulations governing notice or disclosure of known lead-based paint and/or lead-based paint hazards. Neither...

  17. 24 CFR 511.15 - Lead-based paint.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Lead-based paint. 511.15 Section... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

  18. 24 CFR 574.635 - Lead-based paint.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

  19. 40 CFR 745.119 - Impact on State and local requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential Property § 745... governing notice or disclosure of known lead-based paint or lead-based paint hazards. Neither HUD nor EPA...

  20. The effect of occupational exposure to benzo[a]pyrene on neurobehavioral function in coke oven workers.

    PubMed

    Qiu, Chongying; Peng, Bin; Cheng, Shuqun; Xia, Yinyin; Tu, Baijie

    2013-03-01

    Coke oven workers are regularly exposed to polycyclic aromatic hydrocarbons (PAHs). Benzo[a]pyrene (B[a]P), known as an indicator species for PAH contamination, is a neurobehavioral toxicant. The purpose of the study was to evaluate the relationship between B[a]P exposure, a B[a]P-related urinary metabolite and neurobehavioral function among coke oven workers. Coke oven workers and oxygen factory workers participated in this study. B[a]P exposure was monitored by air sampling pump, and urinary 1-hydroxypyrene (1-OHP) level was detected with high performance liquid chromatography (HPLC). A questionnaire and the neurobehavioral core test battery (NCTB) were administered to all subjects. B[a]P-exposed workers were found to have higher urinary 1-OHP levels and worse NCTB performances on eight items than control workers. B[a]P concentrations were higher in the coke oven plant than that in the controls' workplace. The performances on simple reaction time, correct pursuit aiming, and error pursuit aiming decreased with increasing airborne B[a]P in coke oven workers. There were significant correlations between urinary 1-OHP level and six items of the NCTB. Occupational exposure to B[a]P is associated with neurobehavioral function impairment in coke oven workers. Copyright © 2012 Wiley Periodicals, Inc.

  1. 24 CFR 965.701 - Lead-based paint poisoning prevention.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Lead-based paint poisoning...

  2. 40 CFR 745.230 - Work practice standards for conducting lead-based paint activities: public and commercial...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.230 Work practice standards for conducting lead-based paint activities: public... lead-based paint activities: public and commercial buildings, bridges and superstructures. [Reserved...

  3. 40 CFR 745.230 - Work practice standards for conducting lead-based paint activities: public and commercial...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.230 Work practice standards for conducting lead-based paint activities: public... lead-based paint activities: public and commercial buildings, bridges and superstructures. [Reserved...

  4. 24 CFR 200.800 - Lead-based paint.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  5. 40 CFR 63.3176 - What definitions apply to this subpart?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... facility which assembles automobiles or light-duty trucks, including coating facilities and processes. Bake oven air seal means an entry or entry vestibule to or an exit or exit vestibule from a bake oven which isolates the bake oven from the area immediately preceding (for an entry or entry vestibule) or immediately...

  6. 40 CFR 98.172 - GHGs to report.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... combustion units include, but are not limited to, by-product recovery coke oven battery combustion stacks... except you must use the default CO2 emission factors for coke oven gas and blast furnace gas from Table C... flares according to the requirements in § 98.33(c)(2) using the emission factors for coke oven gas and...

  7. Guide for curing of portland cement. Volume I

    DOT National Transportation Integrated Search

    2005-01-01

    This document provides guidance on details of concrete curing practice as they pertain to construction of portland cement concrete pavements. The guide is organized around the major events in curing pavements: curing immediately after placement (init...

  8. 40 CFR 86.317-79 - Hydrocarbon analyzer specifications.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... flame ionization detector (HFID) analyzer. (b) Option. A non-heated flame ionization detector (FID) that... temperature oven housing the detector and sample-handling components. It shall maintain temperature with 2 °C of the set point. The detector, oven, and sample-handling components within the oven shall be...

  9. 40 CFR 86.317-79 - Hydrocarbon analyzer specifications.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... flame ionization detector (HFID) analyzer. (b) Option. A non-heated flame ionization detector (FID) that... temperature oven housing the detector and sample-handling components. It shall maintain temperature with 2 °C of the set point. The detector, oven, and sample-handling components within the oven shall be...

  10. 27. VIEW LOOKING THROUGH A RECTANGULAR COKE OVEN. NOTE THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    27. VIEW LOOKING THROUGH A RECTANGULAR COKE OVEN. NOTE THE USE OF BOTH BRICK AND STONE IN THE CONSTRUCTION OF THE OVEN. - Tower Hill No. 2 Mine, Approximately 0.47 mile Southwest of intersection of Stone Church Road & Township Route 561, Hibbs, Fayette County, PA

  11. 40 CFR 63.309 - Performance tests and procedures.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Standards for Coke Oven Batteries § 63.309 Performance tests and procedures. (a) Except as otherwise... coke oven battery, the results of which shall be used in accordance with procedures specified in this subpart to determine compliance with each of the applicable visible emission limitations for coke oven...

  12. 40 CFR 63.313 - Implementation and enforcement.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Standards for Coke Oven Batteries § 63.313 Implementation and enforcement. (a) This subpart can be... shall notify the coke oven battery owner or operator that inspections and performance tests shall be... Administrator shall give the coke oven battery owner or operator at least 15 days notice that implementation...

  13. 40 CFR 63.306 - Work practice standards.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... for Coke Oven Batteries § 63.306 Work practice standards. (a) Work practice plan. On or before... plan for each coke oven battery. The plan shall be designed to achieve compliance with visible emission limitations for coke oven doors, topside port lids, offtake systems, and charging operations under this...

  14. 40 CFR 63.309 - Performance tests and procedures.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Standards for Coke Oven Batteries § 63.309 Performance tests and procedures. (a) Except as otherwise... coke oven battery, the results of which shall be used in accordance with procedures specified in this subpart to determine compliance with each of the applicable visible emission limitations for coke oven...

  15. 40 CFR 63.313 - Implementation and enforcement.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Standards for Coke Oven Batteries § 63.313 Implementation and enforcement. (a) This subpart can be... shall notify the coke oven battery owner or operator that inspections and performance tests shall be... Administrator shall give the coke oven battery owner or operator at least 15 days notice that implementation...

  16. 40 CFR 63.306 - Work practice standards.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Standards for Coke Oven Batteries § 63.306 Work practice standards. (a) Work practice plan. On or before... plan for each coke oven battery. The plan shall be designed to achieve compliance with visible emission limitations for coke oven doors, topside port lids, offtake systems, and charging operations under this...

  17. 40 CFR 63.309 - Performance tests and procedures.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Standards for Coke Oven Batteries § 63.309 Performance tests and procedures. (a) Except as otherwise... coke oven battery, the results of which shall be used in accordance with procedures specified in this subpart to determine compliance with each of the applicable visible emission limitations for coke oven...

  18. Effect of light-enhanced bleaching on in vitro surface and intrapulpal temperature rise.

    PubMed

    Baik, J W; Rueggeberg, F A; Liewehr, F R

    2001-01-01

    This study investigated the effect of the presence, absence, and aging of a heat-enhancing compound (colorant) added to bleaching gel on the temperature rise of the gel itself, as well as the temperature rise within the pulp chamber, when a tooth was exposed to a variety of light-curing units in vitro. An extracted human upper central incisor was fitted with thermocouples placed in the pulp chamber as well as on the facial tooth surface. A temperature-controlled simulated intrapulpal fluid flow was provided to the tooth, and bleaching agent (Opalesence XTRA, Ultradent) containing heat-enhancing colorant, aged colorant, or no colorant was applied to the facial surface. The tooth and light-curing unit were placed in a thermostatically controlled oven at 37 degrees C, and real-time gel and intrapulpal temperature values were recorded digitally. Light-curing units used were a plasma arc light (PAC) (PowerPac, ADT), a conventional quartz tungsten halogen source (QTH) (Optilux 501, Demetron/Kerr), the QTH light used in high-power (bleaching) mode, and an argon ion laser (AccuCure 3000, LaserMed). An exposure scenario simulating light-enhanced bleaching of 10 upper teeth was developed. Temperature rise over the pre-exposure, baseline value associated with the last light exposure in the bleaching sequence was calculated for each curing and bleaching combination. Five replications for each test condition were made. Temperature rise values were compared using analysis of variance (ANOVA) at a preset alpha of 0.05. When fresh colorant-containing bleach was used, the PAC light increased bleach temperature 39.3 degrees C above baseline. With no added colorant, temperature rise was 37.1 degrees C. The QTH light in bleach mode resulted in gel temperature 24.8 degrees C above baseline, whereas the temperature increase was only 11.5 degrees C when no colorant was used. Conventional QTH light use increased fresh bleach temperature by 17.7 degrees C, whereas an increase of only 11.1 degrees C was measured without colorant. The argon ion laser produced equivalent temperature rise regardless of the presence or freshness of the colorant, approximately 9.4 degrees C. Intrapulpal temperatures were all significantly lower than those recorded in the bleaching gel and ranged from 5 degrees to 8 degrees C. As a rule, the presence of fresh heat-enhancing colorant in the bleaching gel resulted in a significant intrapulpal temperature increase (approximately 1 degrees C) over that reached using other lights. The PAC and the QTH light used in bleach mode induced greater intrapulpal temperature rise than the laser. Freshness of bleaching agent incorporating light-activated, heat-enhancing colorant influences temperature rise of bleaching gel and also may increase intrapulpal temperature values. Use of intense lights does elevate bleach temperature and also results in increased intrapulpal temperature that may further impact on patient sensitivity and pulpal health resulting from this treatment.

  19. 24 CFR 511.15 - Lead-based paint.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Lead-based paint. 511.15 Section 511... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

  20. 24 CFR 1003.607 - Lead-based paint.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

  1. 40 CFR 745.110 - Opportunity to conduct an evaluation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential Property § 745... presence of lead-based paint and/or lead-based paint hazards. (b) Not withstanding paragraph (a) of this...

  2. 24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

  3. 24 CFR 35.135 - Use of paint containing lead.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Use of paint containing lead. 35...

  4. 24 CFR 1003.607 - Lead-based paint.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

  5. 40 CFR 63.3176 - What definitions apply to this subpart?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... facility which assembles automobiles or light-duty trucks, including coating facilities and processes. Bake oven air seal means an entry or entry vestibule to or an exit or exit vestibule from a bake oven which isolates the bake oven from the area immediately preceding (for an entry or entry vestibule) or immediately...

  6. 40 CFR 98.172 - GHGs to report.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... combustion units include, but are not limited to, by-product recovery coke oven battery combustion stacks... flares that burn blast furnace gas or coke oven gas according to the procedures in § 98.253(b)(1) of...)(B) and § 98.253(b)(1)(iii)(C), you must use the default CO2 emission factors for coke oven gas and...

  7. 40 CFR 98.172 - GHGs to report.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... combustion units include, but are not limited to, by-product recovery coke oven battery combustion stacks... flares that burn blast furnace gas or coke oven gas according to the procedures in § 98.253(b)(1) of...)(B) and § 98.253(b)(1)(iii)(C), you must use the default CO2 emission factors for coke oven gas and...

  8. Energy Use and Quality of Foods Cooked by Different Appliances.

    ERIC Educational Resources Information Center

    Odland, Dianne; And Others

    1987-01-01

    The authors compared energy consumption, cooking time, and quality of five foods cooked using electric range surface units and oven, induction cooktop, electric frypan, microwave oven, and toaster oven. The induction cooktop was among the most energy conserving. For most products, cooking treatment had little impact on quality. (Author/CH)

  9. 75 FR 23745 - Jo-Ann Stores, Inc., Provisional Acceptance of a Settlement Agreement and Order

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-04

    ..., therefore, are subject to the requirements of the Commission's Ban of Lead-Containing Paint and Certain Consumer Products Bearing Lead-Containing Paint, 16 CFR part 1303 (the ``Lead-Paint Ban''). Under the Lead-Paint Ban, toys and other children's articles must not bear or contain ``lead-containing paint...

  10. Combination microwave ovens: an innovative design strategy.

    PubMed

    Tinga, Wayne R; Eke, Ken

    2012-01-01

    Reducing the sensitivity of microwave oven heating and cooking performance to load volume, load placement and load properties has been a long-standing challenge for microwave and microwave-convection oven designers. Conventional design problem and solution methods are reviewed to provide greater insight into the challenge and optimum operation of a microwave oven after which a new strategy is introduced. In this methodology, a special load isolating and energy modulating device called a transducer-exciter is used containing an iris, a launch box, a phase, amplitude and frequency modulator and a coupling plate designed to provide spatially distributed coupling to the oven. This system, when applied to a combined microwave-convection oven, gives astounding performance improvements to all kinds of baked and roasted foods including sensitive items such as cakes and pastries, with the only compromise being a reasonable reduction in the maximum available microwave power. Large and small metal utensils can be used in the oven with minimal or no performance penalty on energy uniformity and cooking results. Cooking times are greatly reduced from those in conventional ovens while maintaining excellent cooking performance.

  11. 40 CFR 60.391 - Definitions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

  12. 40 CFR 60.391 - Definitions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

  13. 40 CFR 60.391 - Definitions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

  14. 40 CFR 63.312 - Existing regulations and requirements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... National Emission Standards for Coke Oven Batteries § 63.312 Existing regulations and requirements. (a) The..., topside port lids, coke oven doors, and charging operations in effect on September 15, 1992, or which have... method of monitoring in effect on September 15, 1992, and that ensures coke oven emission reductions...

  15. Sterilization of instruments in solar ovens.

    PubMed

    Jørgensen, A F; Nøhr, K; Boisen, F; Nøhr, J

    2002-01-01

    The sterilization of instruments in rural health clinics in less developed countries is an increasing problem as chemical methods can no longer be recommended and fuel wood is becoming increasingly scarce. It seems obvious, therefore, to utilize solar energy for sterilization purposes. A solar oven was designed and manufactured using local materials and simple tools. It was tested by physical, chemical and microbiological methods and, after successful testing, installed in a rural clinic. The oven was able to generate temperatures above 180 degrees C. On days with direct sunlight the oven fulfilled the international recommendations for hot air sterilization. The chemical indicators, Browne's tubes type 3 and 5, also changed colour. It was difficult to reach the right value for the sterilization effect during months with a low sun position. A moveable oven, or two ovens, must be installed to solve this problem. The solar oven has proven to be a realistic method for the sterilization of instruments. The solar oven is easy to make and use. It saves fuel and can be used in most tropical areas.

  16. A blackbody-pumped CO2-N2 transfer laser

    NASA Astrophysics Data System (ADS)

    Deyoung, R. J.; Higdon, N. S.

    1984-08-01

    A compact blackbody-pumped CO2-N2 transfer laser was constructed and the significant operating parameters were investigated. Lasing was achieved at 10.6 microns by passing preheated N2 through a 1.5-mm-diameter nozzle to a laser cavity where the N2 was mixed with CO2 and He. An intrinsic efficiency of 0.7 percent was achieved for an oven temperature of 1473 K and N2 oven pressure of 440 torr. The optimum laser cavity consisted of a back mirror with maximum reflectivity and an output mirror with 97.5-percent reflectivity. The optimum gas mixture was 1CO2/.5He/6N2. The variation of laser output was measured as a function of oven temperature, nozzle diameter, N2 oven pressure, He and CO2 partial pressures, nozzle-to-oven separation, laser cell temperature, and output laser mirror reflectivity. With these parameters optimized, outputs approaching 1.4 watts were achieved.

  17. Slide Rule For Calculating Curing Schedules

    NASA Technical Reports Server (NTRS)

    Heater, Don

    1995-01-01

    Special-purpose slide rule devised for calculating schedules for storing and curing adhesives, sealants, and other materials characterized by known curing times and shelf lives. Prevents mistakes commonly made in determining storage and curing schedules.

  18. International forensic automotive paint database

    NASA Astrophysics Data System (ADS)

    Bishea, Gregory A.; Buckle, Joe L.; Ryland, Scott G.

    1999-02-01

    The Technical Working Group for Materials Analysis (TWGMAT) is supporting an international forensic automotive paint database. The Federal Bureau of Investigation and the Royal Canadian Mounted Police (RCMP) are collaborating on this effort through TWGMAT. This paper outlines the support and further development of the RCMP's Automotive Paint Database, `Paint Data Query'. This cooperative agreement augments and supports a current, validated, searchable, automotive paint database that is used to identify make(s), model(s), and year(s) of questioned paint samples in hit-and-run fatalities and other associated investigations involving automotive paint.

  19. 40 CFR 745.226 - Certification of individuals and firms engaged in lead-based paint activities: target housing and...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.226 Certification of individuals and firms engaged in lead-based paint activities: target housing... engaged in lead-based paint activities: target housing and child-occupied facilities. 745.226 Section 745...

  20. RESOLVE OVEN Field Demonstration Unit for Lunar Resource Extraction

    NASA Technical Reports Server (NTRS)

    Paz, Aaron; Oryshchyn, Lara; Jensen, Scott; Sanders, Gerald B.; Lee, Kris; Reddington, Mike

    2013-01-01

    The Oxygen and Volatile Extraction Node (OVEN) is a subsystem within the Regolith & Environment Science and Oxygen & Lunar Volatile Extraction (RESOLVE) project. The purpose of the OVEN subsystem is to release volatiles from lunar regolith and extract oxygen by means of a hydrogen reduction reaction. The complete process includes receiving, weighing, sealing, heating, and disposing of core sample segments while transferring all gaseous contents to the Lunar Advanced Volatile Analysis (LAVA) subsystem. This document will discuss the design and performance of the OVEN Field Demonstration Unit (FDU), which participated in the 2012 RESOLVE field demonstration.

  1. Paint for detection of radiological or chemical agents

    DOEpatents

    Farmer, Joseph C [Tracy, CA; Brunk, James L [Martinez, CA; Day, Sumner Daniel [Danville, CA

    2010-08-24

    A paint that warns of radiological or chemical substances comprising a paint operatively connected to the surface, an indicator material carried by the paint that provides an indication of the radiological or chemical substances, and a thermo-activation material carried by the paint. In one embodiment, a method of warning of radiological or chemical substances comprising the steps of painting a surface with an indicator material, and monitoring the surface for indications of the radiological or chemical substances. In another embodiment, a paint is operatively connected to a vehicle and an indicator material is carried by the paint that provides an indication of the radiological or chemical substances.

  2. The synthesis and dynamics research of new curing agent for epoxy resin

    NASA Astrophysics Data System (ADS)

    Peng, Yongli; Huang, Hengyu; Sun, Yong

    2017-05-01

    Two-step synthesis of trimellitic anhydride trimellitic anhydride n - butyl ester (TMNB) was introduced which could be used as an epoxy resin curing agent. The kinetics of the curing reaction was analyzed by N-order model and autocatalytic model. The curing kinetics parameters, the results show that the curing activation energy (Ea) of this system was 35.79kJ / mol. The kinetic equation of curing was d/a d t =2.1061 ×104e x p (-35.79/R T ) α0.5163(l-α ) 0.366 . Combined with β-1 / T extrapolation and experimental adjustment to obtain the resin system curing process: 75°C for 1h, 140°C for 3h, 160°C for 2h.

  3. Eating on Demand

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Under subcontract to McDonnell-Douglas Corporation, Enersyst Development Center developed air impingement technology through oven designs for NASA's Space Station Freedom. Jets of hot air at the top and bottom of the oven are focused on the food, rather than heating the oven cavity as in a traditional thermal oven. By heating the food directly, foods cook faster and more consistently, retaining flavor and texture. Several companies have licensed this technology, including KRh Thermal Systems, which has introduced a line of Hot Choice vending machines. Enersyst has also licensed the first home application to Thermador.

  4. A comparative evaluation of effect of modern-curing lights and curing modes on conventional and novel-resin monomers

    PubMed Central

    Roy, Konda Karthik; Kumar, Kanumuru Pavan; John, Gijo; Sooraparaju, Sujatha Gopal; Nujella, Surya Kumari; Sowmya, Kyatham

    2018-01-01

    Aim: The aim of this study is to compare and to evaluate effect of curing light and curing modes on the nanohybrid composite resins with conventional Bis-GMA and novel tricyclodecane (TCD) monomers. Methodology: Two nanohybrid composites, IPS empress direct and charisma diamond were used in this study. Light-emitting diode (LED)-curing unit and quartz-tungsten-halogen (QTH)-curing unit which were operated into two different modes: continuous and soft start. Based on the composite resin, curing lights, and mode of curing used, the samples were divided into 8 groups. After polymerization, the samples were stored for 48 h in complete darkness at 37°C and 100% humidity. The Vickers hardness (VK) of the surface was determined with Vickers indenter by the application of 200 g for 15 s. Three VK readings were recorded for each sample surface both on top and bottom surfaces. For all the specimens, the three hardness values for each surface were averaged and reported as a single value. The mean VK and hardness ratio were calculated. The depth of cure was assessed based on the hardness ratio. Results: Comparison of mean hardness values and hardness ratios was done using ANOVA with post hoc Tukey's test. Conclusion: Both QTH- and LED-curing units had shown the adequate depth of cure. Soft-start-curing mode in both QTH- and LED-curing lights had effectively increased microhardness than the continuous mode of curing. TCD monomer had shown higher hardness values compared with conventional Bis-GMA-containing resin. PMID:29628651

  5. Influence of seawater mixing and curing on strength characteristics and porosity of ground granulated blast-furnace slag concrete

    NASA Astrophysics Data System (ADS)

    Adiwijaya; Hamada, H.; Sagawa, Y.; Yamamoto, D.

    2017-11-01

    Generally, in the concrete industry, several billion tons of fresh water are annually used for mixing water, curing water and cleaning water. Nevertheless, the utilization of seawater in the concrete industry is prohibited, because it increases the risk of corrosion of steel bars in concrete. This study presents strength characteristics and porosity of seawater mixed concrete and tap water mixed concrete incorporating Ground Granulated Blast-Furnace Slag (GGBS) with water-binder ratio (W/B) of 40%, 50% and 60%. The influence of seawater mixing, GGBS and curing conditions such as tap water curing (TC), seawater curing (SC) and air curing (AC) on the strength and porosity of concrete were evaluated. Based on investigation result, it was shown that there is no significant influence of seawater mixing in improving strength of GGBS concrete up to 365 days in TC and SC. Effectiveness of seawater-mixing on strength enhancement of GGBS concrete is larger in air curing than in water curing. Porosity of seawater-mixed concrete is decreased compared to tap water-mixed concrete in all curing conditions.

  6. Process Modelling of Curing Process-Induced Internal Stress and Deformation of Composite Laminate Structure with Elastic and Viscoelastic Models

    NASA Astrophysics Data System (ADS)

    Li, Dongna; Li, Xudong; Dai, Jianfeng

    2018-06-01

    In this paper, two kinds of transient models, the viscoelastic model and the linear elastic model, are established to analyze the curing deformation of the thermosetting resin composites, and are calculated by COMSOL Multiphysics software. The two models consider the complicated coupling between physical and chemical changes during curing process of the composites and the time-variant characteristic of material performance parameters. Subsequently, the two proposed models are implemented respectively in a three-dimensional composite laminate structure, and a simple and convenient method of local coordinate system is used to calculate the development of residual stresses, curing shrinkage and curing deformation for the composite laminate. Researches show that the temperature, degree of curing (DOC) and residual stresses during curing process are consistent with the study in literature, so the curing shrinkage and curing deformation obtained on these basis have a certain referential value. Compared the differences between the two numerical results, it indicates that the residual stress and deformation calculated by the viscoelastic model are more close to the reference value than the linear elastic model.

  7. Contribution of Bacillus Isolates to the Flavor Profiles of Vanilla Beans Assessed through Aroma Analysis and Chemometrics.

    PubMed

    Gu, Fenglin; Chen, Yonggan; Fang, Yiming; Wu, Guiping; Tan, Lehe

    2015-10-09

    Colonizing Bacillus in vanilla (Vanilla planifolia Andrews) beans is involved in glucovanillin hydrolysis and vanillin formation during conventional curing. The flavor profiles of vanilla beans under Bacillus-assisted curing were analyzed through gas chromatography-mass spectrometry, electronic nose, and quantitative sensory analysis. The flavor profiles were analytically compared among the vanilla beans under Bacillus-assisted curing, conventional curing, and non-microorganism-assisted curing. Vanilla beans added with Bacillus vanillea XY18 and Bacillus subtilis XY20 contained higher vanillin (3.58%±0.05% and 3.48%±0.10%, respectively) than vanilla beans that underwent non-microorganism-assisted curing and conventional curing (3.09%±0.14% and 3.21%±0.15%, respectively). Forty-two volatiles were identified from endogenous vanilla metabolism. Five other compounds were identified from exogenous Bacillus metabolism. Electronic nose data confirmed that vanilla flavors produced through the different curing processes were easily distinguished. Quantitative sensory analysis confirmed that Bacillus-assisted curing increased vanillin production without generating any unpleasant sensory attribute. Partial least squares regression further provided a correlation model of different measurements. Overall, we comparatively analyzed the flavor profiles of vanilla beans under Bacillus-assisted curing, indirectly demonstrated the mechanism of vanilla flavor formation by microbes.

  8. Anisotropic Dielectric Properties of Carbon Fiber Reinforced Polymer Composites during Microwave Curing

    NASA Astrophysics Data System (ADS)

    Zhang, Linglin; Li, Yingguang; Zhou, Jing

    2018-01-01

    Microwave cuing technology is a promising alternative to conventional autoclave curing technology in high efficient and energy saving processing of polymer composites. Dielectric properties of composites are key parameters related to the energy conversion efficiency during the microwave curing process. However, existing methods of dielectric measurement cannot be applied to the microwave curing process. This paper presented an offline test method to solve this problem. Firstly, a kinetics model of the polymer composites under microwave curing was established based on differential scanning calorimetry to describe the whole curing process. Then several specially designed samples of different feature cure degrees were prepared and used to reflect the dielectric properties of the composite during microwave curing. It was demonstrated to be a feasible plan for both test accuracy and efficiency through extensive experimental research. Based on this method, the anisotropic complex permittivity of a carbon fiber/epoxy composite during microwave curing was accurately determined. Statistical results indicated that both the dielectric constant and dielectric loss of the composite increased at the initial curing stage, peaked at the maximum reaction rate point and decreased finally during the microwave curing process. Corresponding mechanism has also been systematically investigated in this work.

  9. 24 CFR 200.800 - Lead-based paint.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 2 2012-04-01 2012-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  10. 24 CFR 965.701 - Lead-based paint poisoning prevention.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Lead-based paint poisoning...

  11. 24 CFR 35.90 - Opportunity to conduct an evaluation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential... inspection for the presence of lead-based paint and/or lead-based paint hazards. (b) Notwithstanding...

  12. 24 CFR 598.408 - Lead-based paint requirements.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

  13. Evaluation of microleakage of class II dental composite resin restorations cured with LED or QTH dental curing light; Blind, Cluster Randomized, In vitro cross sectional study

    PubMed Central

    2014-01-01

    Background The aim of this study is to compare the microleakage of Class II dental composite resin restorations which have been cured by three different LED (light emitting diode) light curing modes compared to control samples cured by QTH (quartz tungsten halogen) light curing units (LCUs), to determine the most effective light curing unit and mode of curing. Results In this experimental study, class II cavities were prepared on 100 sound human premolars which have been extracted for orthodontic treatment. The teeth were randomly divided into four groups; three experimental and one control group of 25 teeth each. Experimental groups were cured by either conventional, pulse-delay, or ramped curing modes of LED. The control group was cured for 20 seconds by QTH. The restorations were thermocycled (1000 times, between 5 and 55°C, for 5 seconds dwell time), dyed, sectioned mesio-distally and viewed under stereo-microscope (40×) magnification. Teeth were then scored on a 0 to 4 scale based on the amount of microleakage. The data were analyzed by Chi-square test. No significant difference was demonstrated between the different LCUs (light curing units), or modes of curing, at the enamel side (p > 0.05). At the dentin side, all modes of LED curing could significantly reduce microleakage (p < 0.05). The results suggest that slow start curing improves marginal integrity and seal. High intense curing endangers those aims. Conclusions Comparison between the three LED mode cured composite resin restorations and QTH curing showed LED curing in all modes is more effective than QTH for reducing microleakage. Both LED and QTH almost completely eliminate the microleakage on the enamel side, however none of them absolutely eliminated microleakage on the dentin side. PMID:24990296

  14. Benzo[a]pyrene-induced neurobehavioral function and neurotransmitter alterations in coke oven workers.

    PubMed

    Niu, Qiao; Zhang, Hongmei; Li, Xin; Li, Meiqin

    2010-07-01

    To study alterations in neurobehavioral function and neurotransmitter levels in coke oven workers occupationally exposed to benzo[a]pyrene (B[a]P) and explore possible biomarkers of B[a]P neurotoxicity. 176 coke oven workers occupationally exposed to B[a]P and 48 warehouse workers (controls) were investigated by questionnaire. Emotional and cognitive function was investigated using the WHO/NCTB. B[a]P concentrations in the working environment, concentrations of monoamine and amino acid neurotransmitters, and levels of urinary 1-hydroxypyrene (1-OH-Py) were assayed by HPLC. Spectrophotometry was used to determine choline neurotransmitter concentrations. Airborne B[a]P concentrations were higher in the coke oven plant than in the controls' workplace, and 1-OH-Py levels were significantly increased in coke workers compared to controls (p=0.000). Digital span and order digital span scores indicated that learning and memory were significantly decreased in coke oven workers (p=0.006). Concentrations of norepinephrine (NE), dopamine, 5-hydroxytryptamine and homovanillic acid were lower, while levels of 5-hydroxyindoleacetic acid were higher in the exposed group compared to controls; the difference in NE was significant (p=0.000). Aspartic acid and gamma-aminobutyric acid levels were significantly decreased in coke oven workers compared to controls (p=0.004 and p=0.004). Acetylcholine (Ach) concentration was four- to fivefold greater in coke oven workers than in controls, while acetylcholine esterase (AchE) activity was significantly decreased (p=0.000 and p=0.012). Statistical analysis showed that digital span and order digital span scores were negatively correlated to Ach and positively correlated to AchE. Occupational B[a]P exposure may reduce coke oven workers' neurobehavioral function and monoamine, amino acid and choline neurotransmitter levels. Moreover, Ach and AchE correlated with neurobehavioral function; AchE has poor specificity, but Ach is a potential biomarker of B[a]P neurotoxicity in coke oven workers.

  15. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Paulauskas, F.L.; Meek, T.T.

    Studies of microwave-assisted curing of neat resins (epoxy) and unidirectional glass and carbon fiber laminates have shown that a substantial reduction in the curing time was obtained. This may be explained by the penetration of microwave energy directly and throughout the laminate with enhancement of the kinetics of the chemical reaction. Results of this work indicate that the microwave assisted curing of glass fiber laminates also shows a substantial reduction of the required curing time. Microwave radiation of 2.45 GHz has been demonstrated to be an acceptable method to cure unidirectional carbon fiber laminates. Also, effective curing of crossply (0/90)more » laminates through this method was observed when proper rotation of the parts accompanied the curing process. This is in accordance with previous work. Multidirectional carbon fiber/epoxy laminates demonstrate a lack of coupling during the curing process. A direct curing of these laminates was not possible by microwave radiation with the experimental approach used, in agreement with previous work. Nevertheless, a moderate reduction in the curing time of these thin laminates was observed due to hybrid curing.« less

  16. Lead paint removal with high-intensity light pulses.

    PubMed

    Grapperhaus, Michael J; Schaefer, Raymond B

    2006-12-15

    This paper presents the results of an initial investigation into using high-intensity incoherent light pulses to strip paint. Measurements of light pulse characteristics, the reflectivity of different paints and initial experiments on the threshold for paint removal, and paint removal are presented, along with an approximate model consistent with experimental results. Paint removal tests include lead paint, the reduction of lead levels to below levels required for lead abatement, as well as air and light emissions measurements that are within regulatory guidelines.

  17. Ultrasonic mixing of epoxy curing agents

    NASA Technical Reports Server (NTRS)

    Hodges, W. T.; St.clair, T. L.

    1983-01-01

    A new technique for mixing solid curing agents into liquid epoxy resins using ultrasonic energy was developed. This procedure allows standard curing agents such as 4,4 prime-diaminodiphenyl sulfone (4,4 prime-DDS) and its 3,3 prime-isomer, (3,3 prime-DDS) to be mixed without prior melting of the curing agent. It also allows curing agents such as 4,4 prime-diaminodiphenyl sulfone (4,4 prime-DDS) and its 3,3 prime-isomer, (3,3 prime-DDS) to be mixed without prior melting of the curing agent. It also allows curing agents with very high melt temperatures such as 4,4 prime-diaminobenzophenone (4,4 prime-DABP) (242 C) to be mixed without premature curing. Four aromatic diamines were ultrasonically blended into MY-720 epoxy resin. These were 4,4 prime-DDS; 3,3 prime-DDA; 4,4 prime-DABP and 3,3 prime-DABP. Unfilled moldings were cast and cured for each system and their physical and mechanical properties compared.

  18. 24 CFR 511.15 - Lead-based paint.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 3 2012-04-01 2012-04-01 false Lead-based paint. 511.15 Section... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

  19. 24 CFR 574.635 - Lead-based paint.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 3 2012-04-01 2012-04-01 false Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

  20. 24 CFR 1003.607 - Lead-based paint.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 4 2013-04-01 2013-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

  1. 24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

  2. 24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

  3. 24 CFR 35.135 - Use of paint containing lead.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Use of paint containing lead. 35...

  4. 24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

  5. Effects of 4-META/MMA-TBB Resin at Different Curing Stages on Osteoblasts and Gingival Epithelial Cells.

    PubMed

    Morotomi, Takahiko; Hirata-Tsuchiya, Shizu; Washio, Ayako; Kitamura, Chiaki

    2016-01-01

    To assess the effects of different curing stages of 4-META/MMA-TBB resin on osteoblasts and gingival keratinocytes. The MC3T3-E1 murine pre-osteoblastic cell line and GE-1 murine gingival epithelial cell line were cultured with mixtures of Super-Bond C&B at different curing stages, and the cell viability was assessed. The alkaline phosphatase (ALP) activity of the MC3T3-E1 cells was also assessed. The majority of the MC3T3-E1 cells died and showed no ALP activity when cultured with 4-META/MMA-TBB resin during the initial curing phase (1 min of curing). A later curing phase of the 4-META/MMA-TBB resin (7 min of curing) showed cytotoxicity at day 1, but the toxic effect was temporary and the proliferative capacity and ALP activity in the cells were similar to control cells at day 7. Completely cured 4-META/MMA-TBB resin (after 1 or 12 h of curing) did not affect the cell viability or ALP activity of the MC3T3-E1 cells. In contrast, 4-META/MMA-TBB resin showed no effect on the GE-1 cells at any stage of curing. Although 4-META/MMA-TBB resin during the initial curing phase shows toxic effects on MC3T3-E1 cells, that cytotoxicity is minimal at later curing phases. In contrast, neither the uncured nor cured resins affected the GE-1 cells.

  6. Thermal Curing Process Monitoring of the Composite Material Using the FBG sensor

    NASA Astrophysics Data System (ADS)

    Zhang, Youhong; Chang, Xinlong; Zhang, Xiaojun; He, Xiangyong

    2018-03-01

    The raw composite material will suffer complex chemical and morphological changes during the thermal curing process, and it is difficult to monitor the curing process and curing effect. In this paper, the FBG sensor was embedded in the raw composite material to monitor the whole curing process. The experiment results showed that the FBG sensor can monitor the resin transformation and residual deformation of the composite material, and the FBG sensor can be applied to monitor the thermal curing process of the composite structure.

  7. 40 CFR 63.3176 - What definitions apply to this subpart?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... facility which assembles automobiles or light-duty trucks, including coating facilities and processes. Bake oven air seal means an entry or entry vestibule to or an exit or exit vestibule from a bake oven which isolates the bake oven from the area immediately preceding (for an entry or entry vestibule) or immediately...

  8. 40 CFR 98.172 - GHGs to report.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... combustion units include, but are not limited to, by-product recovery coke oven battery combustion stacks... flares that burn blast furnace gas or coke oven gas according to the procedures in § 98.253(b)(1) of...)(B) and § 98.253(b)(1)(iii)(C), you must use the default CO2 emission factors for coke oven gas and...

  9. 40 CFR 98.172 - GHGs to report.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... combustion units include, but are not limited to, by-product recovery coke oven battery combustion stacks... flares that burn blast furnace gas or coke oven gas according to the procedures in § 98.253(b)(1) of...)(B) and § 98.253(b)(1)(iii)(C), you must use the default CO2 emission factors for coke oven gas and...

  10. 76 FR 52350 - Coke Oven Emissions Standard; Extension of the Office of Management and Budget's (OMB) Approval...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-22

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2011-0181] Coke... requirements specified in the Standard on Coke Oven Emissions (29 CFR 1910.1029). DATES: Comments must be... obtaining information (29 U.S.C. 657). The information collection requirements in the Coke Oven Emissions...

  11. 46 CFR 32.85-1 - Fireproofing of lamp, oil and paint rooms-T/ALL.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Fireproofing of lamp, oil and paint rooms-T/ALL. 32.85-1..., MACHINERY, AND HULL REQUIREMENTS Lamp and Paint Rooms and Similar Compartments on Tankships § 32.85-1 Fireproofing of lamp, oil and paint rooms—T/ALL. Lamp, oil and paint rooms shall be wholly and tightly lined...

  12. 46 CFR 32.85-1 - Fireproofing of lamp, oil and paint rooms-T/ALL.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 1 2012-10-01 2012-10-01 false Fireproofing of lamp, oil and paint rooms-T/ALL. 32.85-1..., MACHINERY, AND HULL REQUIREMENTS Lamp and Paint Rooms and Similar Compartments on Tankships § 32.85-1 Fireproofing of lamp, oil and paint rooms—T/ALL. Lamp, oil and paint rooms shall be wholly and tightly lined...

  13. There`s a right way to buy exterior house paint and this is the season for it

    Treesearch

    Mark Knaebe

    1998-01-01

    Exterior house paint has undergone some changes in recent years. Designers now have their own brands. And on a technical front, water-based paint now outstrips oil-based paint in quality and durability. You have six decisions to make1 stain versus paint...oil versus latex... type of latex...type of finish...quality level...and brand-name versus generic.

  14. Enamel-based mark performance for marking Chinese mystery snail Bellamya chinensis

    USGS Publications Warehouse

    Wong, Alec; Allen, Craig R.; Hart, Noelle M.; Haak, Danielle M.; Pope, Kevin L.; Smeenk, Nicholas A.; Stephen, Bruce J.; Uden, Daniel R.

    2013-01-01

    The exoskeleton of gastropods provides a convenient surface for carrying marks, and i the interest of improving future marking methods our laboratory assessed the performance of an enamel paint. The endurance of the paint was also compared to other marking methods assessed in the past. We marked the shells of 30 adult Chinese mystery snails Bellamya chinensis and held them in an aquarium for 181 days. We observed no complete degradation of any enamel-paint mark during the 181 days. The enamel-paint mark was superior to a nai;-polish mark, which lasted a median of 100 days. Enamel-paint marks also have a lower rate of loss (0.00 month-1 181 days) than plastic bee tags (0.01 month-1, 57 days), gouache paint (0.07 month-1, 18.5 days), or car body paint from studies found in scientific literature. Legibility of enamel-paint marks had a median lifetime of 102 days. The use of enamel paint on the shells of gastropods is a viable option for studies lasting up to 6 months. Furthermore, visits to capture-mark-recapture site 1 year after application of enamel-paint marks on B. chinesnis shells produced several individuals on which the enamel paint was still visible, although further testing is required to clarify durability over longer periods.

  15. Aerial vehicle with paint for detection of radiological and chemical warfare agents

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Farmer, Joseph C.; Brunk, James L.; Day, S. Daniel

    A paint that warns of radiological or chemical substances comprising a paint operatively connected to the surface, an indicator material carried by the paint that provides an indication of the radiological or chemical substances, and a thermo-activation material carried by the paint. In one embodiment, a method of warning of radiological or chemical substances comprising the steps of painting a surface with an indicator material, and monitoring the surface for indications of the radiological or chemical substances. In another embodiment, a paint is operatively connected to a vehicle and an indicator material is carried by the paint that provides anmore » indication of the radiological or chemical substances.« less

  16. Curing and caring competences in the skills training of physiotherapy students.

    PubMed

    Dahl-Michelsen, Tone

    2015-01-01

    This article explores the significance of curing and caring competences in physiotherapy education, as well as how curing and caring competences intersect within the professional training of physiotherapy students. The empirical data include participant observations and interviews with students attending skills training in the first year of a bachelor's degree program in Norway. Curing and caring are conceptualized as gender-coded competences. That is, curing and caring are viewed as historical and cultural constructions of masculinities and femininities within the physiotherapy profession, as well as performative actions. The findings illuminate the complexity of curing and caring competences in the skills training of physiotherapy students. Curing and caring are both binary and intertwined competences; however, whereas binary competences are mostly concerned with contextual frames, intertwined competences are mostly concerned with performative aspects. The findings also point to how female and male students attend to curing and caring competences in similar ways; thus, the possibilities of transcending traditional gender norms turn out to be significant in this context. The findings suggest that, although curing somehow remains hegemonic to caring, the future generation of physiotherapists seemingly will be able to use their skills for both caring and curing.

  17. Demonstration and Field Test of airjacket technology

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Faulkner, D.; Fisk, W.J.; Gadgil, A.J.

    1998-06-01

    There are approximately 600,000 paint spray workers in the United States applying paints and coatings with some type of sprayer. Approximately 5% of these spray workers are in the South Coast Air Quality Management District (SCAQMD). These spray workers apply paints or other coatings to products such as bridges, houses, automobiles, wood and metal furniture, and other consumer and industrial products. The materials being sprayed include exterior and interior paints, lacquers, primers, shellacs, stains and varnishes. Our experimental findings indicate that the Airjacket does not significantly reduce the exposure of spray workers to paint fumes during HVLP spraying. The differencemore » between ideal and actual spray paint procedures influence the mechanisms driving spray workers exposures to paint fumes and influence the viability of the Airjacket technology. In the ideal procedure, for which the Airjacket was conceived, the spray worker's exposure to paint fumes is due largely to the formation of a recirculating eddy between the spray worker and the object painted. The Airjacket ejects air to diminish and ventilate this eddy. In actual practice, exposures may result largely from directing paint upstream and from the bounce-back of the air/paint jet of the object being painted. The Airjacket, would not be expected to dramatically reduce exposures to paint fumes when the paint is not directed downstream or when the bounce-back of paint on the object creates a cloud of paint aerosols around the spray worker.« less

  18. Investigation into improved pavement curing materials and techniques : part 1 (phases I and II).

    DOT National Transportation Integrated Search

    2002-04-01

    Concrete curing is closely related to cement hydration, microstructure development, and concrete : performance. Application of a liquid membrane-forming curing compound is among the most widely : used curing methods for concrete pavements and bridge ...

  19. 24 CFR 35.1355 - Ongoing lead-based paint maintenance and reevaluation activities.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... at unit turnover and every twelve months. (3) (i) Deteriorated paint. All deteriorated paint on... hazard reduction has been conducted to reduce lead-based paint hazards found in a risk assessment or if...

  20. Analysis and numerical simulation research of the heating process in the oven

    NASA Astrophysics Data System (ADS)

    Chen, Yawei; Lei, Dingyou

    2016-10-01

    How to use the oven to bake delicious food is the most concerned problem of the designers and users of the oven. For this intent, this paper analyzed the heat distribution in the oven based on the basic operation principles and proceeded the data simulation of the temperature distribution on the rack section. Constructing the differential equation model of the temperature distribution changes in the pan when the oven works based on the heat radiation and heat transmission, based on the idea of utilizing cellular automation to simulate heat transfer process, used ANSYS software to proceed the numerical simulation analysis to the rectangular, round-cornered rectangular, elliptical and circular pans and giving out the instantaneous temperature distribution of the corresponding shapes of the pans. The temperature distribution of the rectangular and circular pans proves that the product gets overcooked easily at the corners and edges of rectangular pans but not of a round pan.

  1. Apparatus for making photovoltaic devices

    DOEpatents

    Foote, James B.; Kaake, Steven A. F.; Meyers, Peter V.; Nolan, James F.

    1994-12-13

    A process and apparatus (70) for making a large area photovoltaic device (22) that is capable of generating low cost electrical power. The apparatus (70) for performing the process includes an enclosure (126) providing a controlled environment in which an oven (156) is located. At least one and preferably a plurality of deposition stations (74,76,78) provide heated vapors of semiconductor material within the oven (156) for continuous elevated temperature deposition of semiconductor material on a sheet substrate (24) including a glass sheet (26) conveyed within the oven. The sheet substrate (24) is conveyed on a roller conveyor (184) within the oven (156) and the semiconductor material whose main layer (82) is cadmium telluride is deposited on an upwardly facing surface (28) of the substrate by each deposition station from a location within the oven above the roller conveyor. A cooling station (86) rapidly cools the substrate (24) after deposition of the semiconductor material thereon to strengthen the glass sheet of the substrate.

  2. [Health risk assessment of coke oven PAHs emissions].

    PubMed

    Bo, Xin; Wang, Gang; Wen, Rou; Zhao, Chun-Li; Wu, Tie; Li, Shi-Bei

    2014-07-01

    Polycyclic aromatic hydrocarbons (PAHs) produced by coke oven are with strong toxicity and carcinogenicity. Taken typical coke oven of iron and steel enterprises as the case study, the dispersion and migration of 13 kinds of PAHs emitted from coke oven were analyzed using AERMOD dispersion model, the carcinogenic and non-carcinogenic risks at the receptors within the modeling domain were evaluated using BREEZE Risk Analyst and the Human Health Risk Assessment Protocol for Hazardous Waste Combustion (HHRAP) was followed, the health risks caused by PAHs emission from coke oven were quantitatively evaluated. The results indicated that attention should be paid to the non-carcinogenic risk of naphthalene emission (the maximum value was 0.97). The carcinogenic risks of each single pollutant were all below 1.0E-06, while the maximum value of total carcinogenic risk was 2.65E-06, which may have some influence on the health of local residents.

  3. Reference method for total water in lint cotton by automated oven drying combined with volumetric Karl Fischer titration

    USDA-ARS?s Scientific Manuscript database

    In a preliminary study to measure total water in lint cotton we demonstrated that volumetric Karl Fischer Titration of moisture transported by a carrier gas from an attached small oven is more accurate than standard oven drying in air. The objective of the present study was to assess the measuremen...

  4. Effect of six different cooking techniques in the nutritional composition of two fish species previously selected as optimal for renal patient's diet.

    PubMed

    Castro-González, Isabel; Maafs-Rodríguez, Ana Gabriela; Pérez-Gil Romo, Fernando

    2015-07-01

    Benefits of fish consumption are widely known, but there is little information about nutrient values of raw and cooked fish. The aim was to study the impact that six cooking techniques have on the nutritional composition of two fish species with low content of adverse nutrients in renal diet. Raw and steamed, foiled with aluminum, foiled with banana leaf, gas oven-baked, microwave oven-coked and fried lightly samples were chemically analyzed to determine their protein, phosphorus and lipid content. Crevalle jack: all methods increased lipid and protein content and fatty acids (FA) varied in all cooking methods. Phosphorus decreased in the steamed and microwave oven-cooked samples. Red drum: foiled and fried lightly increased lipid content compared to the raw sample. FA concentration changed in all cooking methods. Protein increased with every technique and phosphorus decreased in the steamed and gas oven-baked samples. Renal patients should preferably consume crevalle jack steamed or microwave oven-cooked and red drum steamed or gas oven-baked.

  5. 40 CFR 745.220 - Scope and applicability.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint... accreditation of training programs for lead-based paint activities and renovations, procedures and requirements for the certification of individuals and firms engaged in lead-based paint activities, and work...

  6. Standard Operating Procedure for the Preparation of Lead-Containing Paint Films and Lead-in-Paint Diagnostic Test Materials

    EPA Science Inventory

    This SOP describes the preparation of stand-alone, lead paint films, prepared according to the old paint recipes. Further, this SOP describes the use of these paint films for the preparation of simulated old paints on a variety of substrates. Substrates used included wood, stee...

  7. 40 CFR 745.226 - Certification of individuals and firms engaged in lead-based paint activities: target housing and...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.226 Certification of individuals and firms engaged in lead-based paint activities: target housing... engaged in lead-based paint activities: target housing and child-occupied facilities. 745.226 Section 745...

  8. 40 CFR 745.119 - Impact on State and local requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential Property § 745... governing notice or disclosure of known lead-based paint or lead-based paint hazards. Neither HUD nor EPA...

  9. 40 CFR 745.119 - Impact on State and local requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential Property § 745... governing notice or disclosure of known lead-based paint or lead-based paint hazards. Neither HUD nor EPA...

  10. 40 CFR 745.226 - Certification of individuals and firms engaged in lead-based paint activities: target housing and...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.226 Certification of individuals and firms engaged in lead-based paint activities: target housing... engaged in lead-based paint activities: target housing and child-occupied facilities. 745.226 Section 745...

  11. Understanding the bias between moisture content by oven drying and water content by Karl Fischer titration at moisture equilibrium

    USDA-ARS?s Scientific Manuscript database

    Multiple causes of the difference between equilibrium moisture and water content have been found. The errors or biases were traced to the oven drying procedure to determine moisture content. The present paper explains the nature of the biases in oven drying and how it is possible to suppress one ...

  12. A blackbody-pumped CO2-N2 transfer laser

    NASA Technical Reports Server (NTRS)

    Deyoung, R. J.; Higdon, N. S.

    1984-01-01

    A compact blackbody-pumped CO2-N2 transfer laser was constructed and the significant operating parameters were investigated. Lasing was achieved at 10.6 microns by passing preheated N2 through a 1.5-mm-diameter nozzle to a laser cavity where the N2 was mixed with CO2 and He. An intrinsic efficiency of 0.7 percent was achieved for an oven temperature of 1473 K and N2 oven pressure of 440 torr. The optimum laser cavity consisted of a back mirror with maximum reflectivity and an output mirror with 97.5-percent reflectivity. The optimum gas mixture was 1CO2/.5He/6N2. The variation of laser output was measured as a function of oven temperature, nozzle diameter, N2 oven pressure, He and CO2 partial pressures, nozzle-to-oven separation, laser cell temperature, and output laser mirror reflectivity. With these parameters optimized, outputs approaching 1.4 watts were achieved.

  13. SEM Analysis of the Interfacial Transition Zone between Cement-Glass Powder Paste and Aggregate of Mortar under Microwave Curing.

    PubMed

    Kong, Yaning; Wang, Peiming; Liu, Shuhua; Zhao, Guorong; Peng, Yu

    2016-08-27

    In order to investigate the effects of microwave curing on the microstructure of the interfacial transition zone of mortar prepared with a composite binder containing glass powder and to explain the mechanism of microwave curing on the improvement of compressive strength, in this study, the compressive strength of mortar under microwave curing was compared against mortar cured using (a) normal curing at 20 ± 1 °C with relative humidity (RH) > 90%; (b) steam curing at 40 °C for 10 h; and (c) steam curing at 80 °C for 4 h. The microstructure of the interfacial transition zone of mortar under the four curing regimes was analyzed by Scanning electron microscopy (SEM). The results showed that the improvement of the compressive strength of mortar under microwave curing can be attributed to the amelioration of the microstructure of the interfacial transition zone. The hydration degree of cement is accelerated by the thermal effect of microwave curing and Na⁺ partially dissolved from the fine glass powder to form more reticular calcium silicate hydrate, which connects the aggregate, calcium hydroxide, and non-hydrated cement and glass powder into a denser integral structure. In addition, a more stable triangular structure of calcium hydroxide contributes to the improvement of compressive strength.

  14. A finite element/level set model of polyurethane foam expansion and polymerization

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Rao, Rekha R.; Long, Kevin Nicholas; Roberts, Christine Cardinal

    Polyurethane foams are used widely for encapsulation and structural purposes because they are inexpensive, straightforward to process, amenable to a wide range of density variations (1 lb/ft3 - 50 lb/ft3), and able to fill complex molds quickly and effectively. Computational model of the filling and curing process are needed to reduce defects such as voids, out-of-specification density, density gradients, foam decomposition from high temperatures due to exotherms, and incomplete filling. This paper details the development of a computational fluid dynamics model of a moderate density PMDI structural foam, PMDI-10. PMDI is an isocyanate-based polyurethane foam, which is chemically blown withmore » water. The polyol reacts with isocyanate to produces the polymer. PMDI- 10 is catalyzed giving it a short pot life: it foams and polymerizes to a solid within 5 minutes during normal processing. To achieve a higher density, the foam is over-packed to twice or more of its free rise density of 10 lb/ft3. The goal for modeling is to represent the expansion, filling of molds, and the polymerization of the foam. This will be used to reduce defects, optimize the mold design, troubleshoot the processed, and predict the final foam properties. A homogenized continuum model foaming and curing was developed based on reaction kinetics, documented in a recent paper; it uses a simplified mathematical formalism that decouples these two reactions. The chemo-rheology of PMDI is measured experimentally and fit to a generalized- Newtonian viscosity model that is dependent on the extent of cure, gas fraction, and temperature. The conservation equations, including the equations of motion, an energy balance, and three rate equations are solved via a stabilized finite element method. The equations are combined with a level set method to determine the location of the foam-gas interface as it evolves to fill the mold. Understanding the thermal history and loads on the foam due to exothermicity and oven curing is very important to the results, since the kinetics, viscosity, and other material properties are all sensitive to temperature. Results from the model are compared to experimental flow visualization data and post-test X-ray computed tomography (CT) data for the density. Several geometries are investigated including two configurations of a mock structural part and a bar geometry to specifically test the density model. We have found that the model predicts both average density and filling profiles well. However, it under predicts density gradients, especially in the gravity direction. Further model improvements are also discussed for future work.« less

  15. Curing kinetics of visible light curing dental resin composites investigated by dielectric analysis (DEA).

    PubMed

    Steinhaus, Johannes; Hausnerova, Berenika; Haenel, Thomas; Großgarten, Mandy; Möginger, Bernhard

    2014-03-01

    During the curing process of light curing dental composites the mobility of molecules and molecule segments is reduced leading to a significant increase of the viscosity as well as the ion viscosity. Thus, the kinetics of the curing behavior of 6 different composites was derived from dielectric analysis (DEA) using especially redesigned flat sensors with interdigit comb electrodes allowing for irradiation at the top side and measuring the ion viscosity at the bottom side. As the ion viscosities of dental composites change 1-3 orders of magnitude during the curing process, DEA provides a sensitive approach to evaluate their curing behavior, especially in the phase of undisturbed chain growth. In order to determine quantitative kinetic parameters a kinetic model is presented and examined for the evaluation of the ion viscosity curves. From the obtained results it is seen that DEA might be employed in the investigation of the primary curing process, the quality assurance of ingredients as well as the control of processing stability of the light curing dental composites. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  16. 40 CFR 745.239 - Effective dates.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities... or firm shall perform, offer, or claim to perform lead-based paint activities, as defined in this... 1, 2000. (c) All lead-based paint activities shall be performed pursuant to the work practice...

  17. 40 CFR 745.239 - Effective dates.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities... or firm shall perform, offer, or claim to perform lead-based paint activities, as defined in this... 1, 2000. (c) All lead-based paint activities shall be performed pursuant to the work practice...

  18. Temperature rise induced by some light emitting diode and quartz-tungsten-halogen curing units.

    PubMed

    Asmussen, Erik; Peutzfeldt, Anne

    2005-02-01

    Because of the risk of thermal damage to the pulp, the temperature rise induced by light-curing units should not be too high. LED (light emitting diode) curing units have the main part of their irradiation in the blue range and have been reported to generate less heat than QTH (quartz-tungsten-halogen) curing units. This study had two aims: first, to measure the temperature rise induced by ten LED and three QTH curing units; and, second, to relate the measured temperature rise to the power density of the curing units. The light-induced temperature rise was measured by means of a thermocouple embedded in a small cylinder of resin composite. The power density was measured by using a dental radiometer. For LED units, the temperature rise increased with increasing power density, in a statistically significant manner. Two of the three QTH curing units investigated resulted in a higher temperature rise than LED curing units of the same power density. Previous findings, that LED curing units induce less temperature rise than QTH units, does not hold true in general.

  19. 40 CFR 745.220 - Scope and applicability.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint... accreditation of training programs for lead-based paint activities and renovations, procedures and requirements for the certification of individuals and firms engaged in lead-based paint activities, and work...

  20. 40 CFR 745.220 - Scope and applicability.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint... accreditation of training programs for lead-based paint activities and renovations, procedures and requirements for the certification of individuals and firms engaged in lead-based paint activities, and work...

  1. Method for sintering fuel cell electrodes using a carrier

    DOEpatents

    Donelson, R.; Bryson, E.S.

    1995-03-28

    A carrier is described for conveying components of a fuel cell to be sintered through a sintering furnace. The carrier comprises a metal sheet coated with a carbon-based paint, the carbon-based paint comprising an organic binder. The carbon-based paint may be an alcohol or a solvent-based paint or a water-based paint.

  2. Epoxy-paint stripping using TEA CO2 laser: Determination of threshold fluence and the process parameters

    NASA Astrophysics Data System (ADS)

    Kumar, Manoj; Bhargava, P.; Biswas, A. K.; Sahu, Shasikiran; Mandloi, V.; Ittoop, M. O.; Khattak, B. Q.; Tiwari, M. K.; Kukreja, L. M.

    2013-03-01

    It is shown that the threshold fluence for laser paint stripping can be accurately estimated from the heat of gasification and the absorption coefficient of the epoxy-paint. The threshold fluence determined experimentally by stripping of the epoxy-paint on a substrate using a TEA CO2 laser matches closely with the calculated value. The calculated threshold fluence and the measured absorption coefficient of the paint allowed us to determine the epoxy paint thickness that would be removed per pulse at a given laser fluence even without experimental trials. This was used to predict the optimum scan speed required to strip the epoxy-paint of a given thickness using a high average power TEA CO2 laser. Energy Dispersive X-Ray Fluorescence (EDXRF) studies were also carried out on laser paint-stripped concrete substrate to show high efficacy of this modality.

  3. SEM Analysis of the Interfacial Transition Zone between Cement-Glass Powder Paste and Aggregate of Mortar under Microwave Curing

    PubMed Central

    Kong, Yaning; Wang, Peiming; Liu, Shuhua; Zhao, Guorong; Peng, Yu

    2016-01-01

    In order to investigate the effects of microwave curing on the microstructure of the interfacial transition zone of mortar prepared with a composite binder containing glass powder and to explain the mechanism of microwave curing on the improvement of compressive strength, in this study, the compressive strength of mortar under microwave curing was compared against mortar cured using (a) normal curing at 20 ± 1 °C with relative humidity (RH) > 90%; (b) steam curing at 40 °C for 10 h; and (c) steam curing at 80 °C for 4 h. The microstructure of the interfacial transition zone of mortar under the four curing regimes was analyzed by Scanning electron microscopy (SEM). The results showed that the improvement of the compressive strength of mortar under microwave curing can be attributed to the amelioration of the microstructure of the interfacial transition zone. The hydration degree of cement is accelerated by the thermal effect of microwave curing and Na+ partially dissolved from the fine glass powder to form more reticular calcium silicate hydrate, which connects the aggregate, calcium hydroxide, and non-hydrated cement and glass powder into a denser integral structure. In addition, a more stable triangular structure of calcium hydroxide contributes to the improvement of compressive strength. PMID:28773854

  4. [Aerosol size distribution of organic carbon and elemental carbon on the top of coke oven and in the plant area].

    PubMed

    Liu, Xiao-Feng; Peng, Lin; Bai, Hui-Ling; Mu, Ling; Song, Chong-Fang

    2013-08-01

    In order to investigate the characteristic of organic carbon (OC) and elemental carbon (EC) in particles on the top of coke oven and in the plant area, the particle matter samples of five size fraction including < or = 1.4 microm, 1.4-2.1 microm, 2.1-4.2 microm, 4.2-10.2 microm and > or = 10.2 microm were collected using Staplex234 cascade impactor, and OC and EC were analyzed by Elementar Analysensysteme GmbH vario EL cube. The mass concentrations of OC and EC associated with TSP on the top of coke oven were 291.6 microg x m(-3) and 255.1 microg x m(-3), while those in the plant area were 377.8 microg x m(-3) and 151.7 microg x m(-3). The mass concentration of secondary organic carbon (SOC) in particles with size of < or = 1.4 microm was 147.3 microg x m(-3) in the plant area. The value of OC/EC in particles less than 2.1 microm was 1.3 on the top of coke oven. The mass concentration of EC in TSP in the plant area was lower than that on the top of coke oven, while the mass concentration of OC in the plant area was significantly higher than that on the top of coke oven. The mass concentrations of OC and EC associated with particles less than 10.2 microm in the plant area were far higher than those in the atmosphere of area where the coke plant is located. The OC and EC in particles, which were collected both on the top of coke oven and in the plant area, were mainly enriched in fine particles. The size distribution of OC showed a clear distinction between the coke oven top and the plant area, which revealed that OC in the plant area was more preferably enriched in fine particles than that on the top of coke oven, and the same size distribution of EC was found on the top of coke oven and in the plant area. In the plant area, the mass concentration of SOC and the contribution of SOC to OC increased with the decreasing diameter in particles with diameter of less than 10.2 microm.

  5. 29 CFR 1915.33 - Chemical paint and preservative removers.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 7 2014-07-01 2014-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

  6. 24 CFR 570.461 - Post-preliminary approval requirements; lead-based paint.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... requirements; lead-based paint. 570.461 Section 570.461 Housing and Urban Development Regulations Relating to... GRANTS Urban Development Action Grants § 570.461 Post-preliminary approval requirements; lead-based paint. The recipient may receive preliminary approval prior to the accomplishment of lead-based paint...

  7. 48 CFR 1436.570 - Prohibition against use of lead-based paint.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... lead-based paint. 1436.570 Section 1436.570 Federal Acquisition Regulations System DEPARTMENT OF THE... 1436.570 Prohibition against use of lead-based paint. (a) Definitions. As used in this section... of Lead-Based Paint, in solicitations and contracts when construction of residential structures or...

  8. 24 CFR 570.608 - Lead-based paint.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Lead-based paint. 570.608 Section... DEVELOPMENT COMMUNITY FACILITIES COMMUNITY DEVELOPMENT BLOCK GRANTS Other Program Requirements § 570.608 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead...

  9. 40 CFR 745.223 - Definitions.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    .... Abatement means any measure or set of measures designed to permanently eliminate lead-based paint hazards... elimination of lead-based paint hazards; or (B) Are designed to permanently eliminate lead-based paint hazards..., when such activities are not designed to permanently eliminate lead-based paint hazards, but, instead...

  10. 40 CFR 745.223 - Definitions.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    .... Abatement means any measure or set of measures designed to permanently eliminate lead-based paint hazards... elimination of lead-based paint hazards; or (B) Are designed to permanently eliminate lead-based paint hazards..., when such activities are not designed to permanently eliminate lead-based paint hazards, but, instead...

  11. 24 CFR 35.165 - Prior evaluation or hazard reduction.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.165 Prior evaluation or... conditions: (a) Lead-based paint inspection. (1) A lead-based paint inspection conducted before March 1, 2000...

  12. 24 CFR 35.165 - Prior evaluation or hazard reduction.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.165 Prior evaluation or... conditions: (a) Lead-based paint inspection. (1) A lead-based paint inspection conducted before March 1, 2000...

  13. 24 CFR 35.165 - Prior evaluation or hazard reduction.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.165 Prior evaluation or... conditions: (a) Lead-based paint inspection. (1) A lead-based paint inspection conducted before March 1, 2000...

  14. 40 CFR 745.61 - Scope and applicability.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Hazards § 745.61 Scope and applicability. (a) This subpart identifies lead-based paint hazards. (b) The standards for lead-based paint hazards apply to target housing and child-occupied facilities. (c) Nothing in...

  15. Evaluation of Portland cement concrete with internal curing capabilities : tech summary.

    DOT National Transportation Integrated Search

    2016-09-01

    Proper curing is the key to durable and sustainable concrete structures. When a concrete mixture is : designed, delivered, poured, and consolidated, curing is the last and the most critical part for a quality final : product. Insufficient curing of c...

  16. Microwave Meat Roasting - A Computer Analysis for Cylindrical Roasts

    DTIC Science & Technology

    1977-07-01

    Temperatures for Various Oven Temperature Settings Table A2. Radiosity Values for Various Oven Temperature Settings Table A3. Radiant Energy Received by...the radiosities Jj, were written for the measured surface temperatures for each oven setting. Using the calculated radiosities , radiant heat...transfer to the roast was calculated by multiplying the difference in radiosities by the shape factor. Appendix A shows the details, and the slopes and

  17. Effect of long steam curing durations on the strength of A5 concrete.

    DOT National Transportation Integrated Search

    1976-01-01

    Based on the results of this investigation in which the longest steam curing time was 72 hours, it was concluded that increasing the curing times did not adversely affect the strength of the concrete. However, at the later stages of steam curing, gai...

  18. 40 CFR 745.239 - Effective dates.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities... or firm shall perform, offer, or claim to perform lead-based paint activities, as defined in this... 1, 2000. (c) All lead-based paint activities shall be performed pursuant to the work practice...

  19. 40 CFR 745.220 - Scope and applicability.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint... accreditation of training programs for lead-based paint activities and renovations, procedures and requirements for the certification of individuals and firms engaged in lead-based paint activities, and work...

  20. 21 CFR 170.60 - Nitrites and/or nitrates in curing premixes.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Nitrites and/or nitrates in curing premixes. 170... and Decisions § 170.60 Nitrites and/or nitrates in curing premixes. (a) Nitrites and/or nitrates are.... (b) Nitrites and/or nitrates, when packaged separately from flavoring and seasoning in curing...

  1. Sensory and analytical evaluations of paints with and without texanol.

    PubMed

    Gallagher, Michelle; Dalton, Pamela; Sitvarin, Laura; Preti, George

    2008-01-01

    Perception of odor can figure prominently in complaints about indoor air,yet identification of the responsible compound(s) is often difficult. For example, paint emissions contain a variety of odorous volatile organic compounds (VOCs) which maytrigger reports of irritation and upper respiratory health effects. Texanol ester alcohol (2,2,4-trimethyl-1,3-pentanediol monoisobutyrate), a paint coalescing agent, is frequently associated with the "persistent, characteristic odor" of water-based paint. To evaluate the sensory impact of Texanol, naive (unfamiliar with paint constituents) and experienced (familiar with paint constituents) subjects evaluated the odor properties of paints with and without Texanol. VOC emissions from neat paint and paint applied to gypsum wallboard were collected via solid-phase microextraction and analyzed by gas chromatography/ mass spectrometry and gas chromatography/olfactometry. Regardless of subjects' prior experience, aromatic hydrocarbons and oxygenated compounds, introduced from other paint additives and not Texanol, were most commonly associated with paint odor. However, quantitative sensory techniques demonstrated that addition of Texanol to paints led to an overall increase in the perceived intensity of the coating. The combined use of these techniques proved to be an effective methodology for analyzing the structure of paint volatiles and their sensory properties and holds promise for solving many odorous indoor air problems.

  2. Development of a water-jet assisted laser paint removal process

    NASA Astrophysics Data System (ADS)

    Madhukar, Yuvraj K.; Mullick, Suvradip; Nath, Ashish K.

    2013-12-01

    The laser paint removal process usually leaves behind traces of combustion product i.e. ashes on the surface. An additional post-processing such as light-brushing or wiping by some mechanical means is required to remove the residual ash. In order to strip out the paint completely from the surface in a single step, a water-jet assisted laser paint removal process has been investigated. The 1.07 μm wavelength of Yb-fiber laser radiation has low absorption in water; therefore a high power fiber laser was used in the experiment. The laser beam was delivered on the paint-surface along with a water jet to remove the paint and residual ashes effectively. The specific energy, defined as the laser energy required removing a unit volume of paint was found to be marginally more than that for the gas-jet assisted laser paint removal process. However, complete paint removal was achieved with the water-jet assist only. The relatively higher specific energy in case of water-jet assist is mainly due to the scattering of laser beam in the turbulent flow of water-jet.

  3. 76 FR 17379 - National Tree-Marking Paint Committee Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-29

    ... DEPARTMENT OF AGRICULTURE Forest Service National Tree-Marking Paint Committee Meeting AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The National Tree-Marking Paint Committee will... related to improvements in, concerns about, and the handling and use of tree-marking paint by personnel of...

  4. 40 CFR 745.238 - Fees for accreditation and certification of lead-based paint activities.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... certification of lead-based paint activities. 745.238 Section 745.238 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.238 Fees for accreditation and certification of lead...

  5. 40 CFR 745.238 - Fees for accreditation and certification of lead-based paint activities.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... certification of lead-based paint activities. 745.238 Section 745.238 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.238 Fees for accreditation and certification of lead...

  6. What You Should Know about Using Paint Strippers

    MedlinePlus

    ... consumers are choosing to complete do-it-yourself (DIY) projects in their homes. Using paint strippers in ... chance of flammable paint stripper fumes catching fire. DIY use of methylene chloride-based paint strippers has ...

  7. Multiphoton laser ionization for energy conversion in barium vapor

    NASA Astrophysics Data System (ADS)

    Makdisi, Y.; Kokaj, J.; Afrousheh, K.; Mathew, J.; Nair, R.; Pichler, G.

    2013-03-01

    We have studied the ion detection of barium atoms in special heated ovens with a tungsten rod in the middle of the stainless steel tube. The tungsten rod was heated indirectly by the oven body heaters. A bias voltage between the cell body and the tungsten rod of 9 V was used to collect electrons, after the barium ions had been created. However, we could collect the electrons even without the bias voltage, although with ten times less efficiency. We studied the conditions for the successful bias-less thermionic signal detection using excimer/dye laser two-photon excitation of Rydberg states below and above the first ionization limit (two-photon wavelength at 475.79 nm). We employed a hot-pipe oven and heat-pipe oven (with inserted mesh) in order to generate different barium vapor distributions inside the oven. The thermionic signal increased by a factor of two under heat-pipe oven conditions.

  8. 46 CFR 32.85-1 - Fireproofing of lamp, oil and paint rooms-T/ALL.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 1 2011-10-01 2011-10-01 false Fireproofing of lamp, oil and paint rooms-T/ALL. 32.85-1..., MACHINERY, AND HULL REQUIREMENTS Lamp and Paint Rooms and Similar Compartments on Tankships § 32.85-1 Fireproofing of lamp, oil and paint rooms—T/ALL. Lamp, oil and paint rooms shall be wholly and tightly lined...

  9. 46 CFR 32.85-1 - Fireproofing of lamp, oil and paint rooms-T/ALL.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 1 2013-10-01 2013-10-01 false Fireproofing of lamp, oil and paint rooms-T/ALL. 32.85-1..., MACHINERY, AND HULL REQUIREMENTS Lamp and Paint Rooms and Similar Compartments on Tankships § 32.85-1 Fireproofing of lamp, oil and paint rooms—T/ALL. Lamp, oil and paint rooms shall be wholly and tightly lined...

  10. 46 CFR 32.85-1 - Fireproofing of lamp, oil and paint rooms-T/ALL.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 1 2014-10-01 2014-10-01 false Fireproofing of lamp, oil and paint rooms-T/ALL. 32.85-1..., MACHINERY, AND HULL REQUIREMENTS Lamp and Paint Rooms and Similar Compartments on Tankships § 32.85-1 Fireproofing of lamp, oil and paint rooms—T/ALL. Lamp, oil and paint rooms shall be wholly and tightly lined...

  11. Comparison of light transmittance in different thicknesses of zirconia under various light curing units

    PubMed Central

    Egilmez, Ferhan; Ergun, Gulfem

    2012-01-01

    PURPOSE The objective of this study was to compare the light transmittance of zirconia in different thicknesses using various light curing units. MATERIALS AND METHODS A total of 21 disc-shaped zirconia specimens (5 mm in diameter) in different thicknesses (0.3, 0.5 and 0.8 mm) were prepared. The light transmittance of the specimens under three different light-curing units (quartz tungsten halogen, light-emitting diodes and plasma arc) was compared by using a hand-held radiometer. Statistical significance was determined using two-way ANOVA (α=.05). RESULTS ANOVA revealed that thickness of zirconia and light curing unit had significant effects on light transmittance (P<.001). CONCLUSION Greater thickness of zirconia results in lower light transmittance. Light-emitting diodes light-curing units might be considered as effective as Plasma arc light-curing units or more effective than Quartz-tungsten-halogen light-curing units for polymerization of the resin-based materials. PMID:22737314

  12. The Effect of Fermentation and Drying on Clicanthus Nutans Lindai Extract Chemical Constituents and Bioactivity

    NASA Astrophysics Data System (ADS)

    Lee, Y. Y.; Teh, P. S.; Kumaresan, S.; Tiong, C. H.

    2017-06-01

    In this study, two processes (fermentation and drying) were conducted on Clicanthus Nutans Lindau, which is well-known for its antioxidant activities. The aim of this research is to investigate the effects of these processes towards the Total Phenolic Content (TPC), antioxidant activity and the crude yield of the leaves. For the fermentation process, the fermentation time is varied for 6, 12, 24, 48 and 72 hours. For drying, oven drying (40, 45 and 50°C, freeze-drying and shade drying are investigated. Blanching was also conducted for oven dried samples (90°C for 1 minute). It was found that 12 hours fermentation produced the highest yield corresponding to Total Phenolic Content at 0.33 while 6 hours fermentation produced the highest Antioxidant Activity and yield at 2.218 x 10-10 mg/mL and 0.64 . On the other hand, 48 hours fermentation produced the highest overall extract yield at 0.64 . Analysis for antioxidant activity was carried out using 2,2-diphenyl-1-picrylhydrazyl (DPPH) and Folin-Ciocalteau method for Total Phenolic Content. Thermal inactivation kinetics (blanching) has been investigated for oven drying samples. Results showed that 40°C oven drying and 50°C oven drying with blanching has better retention of bioactive constituents. Blanching has no significant effect on phenolic content but has increased the crude extract for higher temperature oven drying. It has no positive effect on antioxidant activity. Drying is also a better processing method compared to fermentation as drying has slightly favorable results in all three aspects. Through comparison with extraction time of 60 minutes for 40°C oven drying and 6 hour fermented samples, yield of total phenolic content and overall yield of oven dried sample is higher than fermented sample by 4.14 and 0.39 respectively as well as showing better antioxidant activity.

  13. Evaluation of biomarkers in plasma, blood, and urine samples from coke oven workers: significance of exposure to polycyclic aromatic hydrocarbons.

    PubMed Central

    Ovrebø, S; Haugen, A; Farmer, P B; Anderson, D

    1995-01-01

    OBJECTIVE--The aim was to assess the significance of two biomarkers; antibody to benzo(a)pyrene DNA adducts and concentration of hydroxyethylvaline haemoglobin adducts in samples from a well studied group of coke oven workers. As a measure of exposure we have used 1-hydroxypyrene in urine. METHODS--Urine and blood samples were collected from coke oven workers and a control group. Samples from coke oven plant workers were collected in January and June. 1-Hydroxypyrene was measured in urine by high performance liquid chromatography (HPLC), antibodies to benzo(a)pyrene DNA adducts were measured by ELISA and hydroxyethylvaline haemoglobin adducts were measured by gas chromatography-mass spectrometry (GC-MS). RESULTS--Mean urinary 1-hydroxypyrene in samples from coke oven workers varied from 1.11 to 5.53 umol/mol creatinine and 0.14 umol/mol creatinine in the control group. Workers at the top side had the highest values of urinary 1-hydroxypyrene. Antibody to benzo(a)pyrene DNA adducts did not correlate with either 1-hydroxypyrene nor length of work at the coke oven plant. But antibody concentration in samples collected in January was predictive of the concentration in samples collected in June. A small non-significant increase in hydroxyethylvaline haemoglobin adducts was found in samples from coke oven workers relative to the control group when comparing smokers and nonsmokers separately. CONCLUSION--1-Hydroxypyrene correlates well with exposure groups based on job description. Antibodies to benzo(a)-pyrene DNA adducts was related to people and not exposure. Work at a coke oven plant might lead to increased hydroxyethylvaline haemoglobin adducts. PMID:8535495

  14. Use of sodium dodecyl sulfate pretreatment and 2-stage curing for improved quality of salted duck eggs.

    PubMed

    Lian, Zixuan; Qiao, Longshan; Zhu, Guanghong; Deng, Yun; Qian, Bingjun; Yue, Jin; Zhao, Yanyun

    2014-03-01

    The effects of use of sodium dodecyl sulfate (SDS) pretreatment and 2-stage curing on the microbial, physicochemical, and microstructural qualities of salted duck eggs were studied. After pretreatment in 0.5% (w/v) SDS solution at room conditions for 15 min, no discolorations were observed and no microorganisms were detected on the egg shells. In the 2-stage curing process, 25% (w/v) and 30% (w/v) saline solutions were evaluated in the 1st step (Stage I, approximately 18 d), whereas 4% (w/v) saline solution was applied in the 2nd step (Stage II, approximately 15 d). Along with increased curing time, water content decreased and NaCl content increased in the egg yolks from approximately 0.40% to 0.86%, whereas the water content of egg albumen remained at approximately 85% during the 2-stage curing. More importantly, the NaCl content of albumen maintained at approximately 4.0% at Stage II curing. Yolk index as a sign of maturity for salted duck eggs reached 1 at the end of Stage I (18 d) and retained the same value during Stage II curing regardless of the NaCl concentration in the Stage I saline solution. Oil exudation in egg yolks increased as the time of curing increased. As seen from scanning electron microscopy, oil was released from yolk granules. This study indicated that SDS pretreatment is effective to reduce microbial load on the shells of fresh duck eggs and the 2-stage curing can improve physicochemical qualities of the salted duck eggs and shortened curing time to about 7 to 17 d as compared to the traditional 1-step curing method. Spoiled saline solution and uneven distribution of salt are the 2 major problems in producing salted duck eggs. Sodium dodecyl sulfate (SDS) pretreatment and 2-stage curing process have shown effective to solve these problems, respectively. The SDS pretreatment was able to remove microorganisms and soil from the surface of fresh egg shells, thus preventing the spoilage of the saline solution. The 2-stage curing process successfully controlled the NaCl content of egg albumen and yolk in the final product, and shortened the curing time compared to the traditional 1-step curing method. © 2014 Institute of Food Technologists®

  15. 29 CFR 1915.33 - Chemical paint and preservative removers.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 7 2012-07-01 2012-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

  16. 48 CFR 1436.570 - Prohibition against use of lead-based paint.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... lead-based paint. 1436.570 Section 1436.570 Federal Acquisition Regulations System DEPARTMENT OF THE... 1436.570 Prohibition against use of lead-based paint. (a) Definitions. As used in this section... of Lead-Based Paint, in solicitations and contracts when construction of residential structures or...

  17. 24 CFR 35.1220 - Ongoing lead-based paint maintenance activities.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Tenant-Based Rental Assistance § 35.1220 Ongoing lead-based paint maintenance activities...

  18. 24 CFR 570.608 - Lead-based paint.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 3 2014-04-01 2013-04-01 true Lead-based paint. 570.608 Section... DEVELOPMENT COMMUNITY FACILITIES COMMUNITY DEVELOPMENT BLOCK GRANTS Other Program Requirements § 570.608 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead...

  19. 40 CFR 745.223 - Definitions.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    .... Abatement means any measure or set of measures designed to permanently eliminate lead-based paint hazards... elimination of lead-based paint hazards; or (B) Are designed to permanently eliminate lead-based paint hazards..., when such activities are not designed to permanently eliminate lead-based paint hazards, but, instead...

  20. 24 CFR 35.1340 - Clearance.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... abatement of lead-based paint or lead-based paint hazards shall be performed in accordance with 40 CFR 745...

  1. 24 CFR 35.1340 - Clearance.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... abatement of lead-based paint or lead-based paint hazards shall be performed in accordance with 40 CFR 745...

  2. 40 CFR 745.61 - Scope and applicability.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Hazards § 745.61 Scope and applicability. (a) This subpart identifies lead-based paint hazards. (b) The standards for lead-based paint hazards apply to target housing and child-occupied facilities. (c) Nothing in...

  3. 24 CFR 35.165 - Prior evaluation or hazard reduction.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.165 Prior evaluation or... conditions: (a) Lead-based paint inspection. (1) A lead-based paint inspection conducted before March 1, 2000...

  4. 40 CFR 745.61 - Scope and applicability.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Hazards § 745.61 Scope and applicability. (a) This subpart identifies lead-based paint hazards. (b) The standards for lead-based paint hazards apply to target housing and child-occupied facilities. (c) Nothing in...

  5. 29 CFR 1915.33 - Chemical paint and preservative removers.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 7 2011-07-01 2011-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

  6. 24 CFR 570.461 - Post-preliminary approval requirements; lead-based paint.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... requirements; lead-based paint. 570.461 Section 570.461 Housing and Urban Development Regulations Relating to... GRANTS Urban Development Action Grants § 570.461 Post-preliminary approval requirements; lead-based paint. The recipient may receive preliminary approval prior to the accomplishment of lead-based paint...

  7. Terahertz NDE for Under Paint Corrosion Detection and Evaluation

    NASA Technical Reports Server (NTRS)

    Anastasi, Robert F.; Madaras, Eric I.

    2005-01-01

    Corrosion under paint is not visible until it has caused paint to blister, crack, or chip. If corrosion is allowed to continue then structural problems may develop. Identifying corrosion before it becomes visible would minimize repairs and costs and potential structural problems. Terahertz NDE imaging under paint for corrosion is being examined as a method to inspect for corrosion by examining the terahertz response to paint thickness and to surface roughness.

  8. 40 CFR 745.239 - Effective dates.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities... or firm shall perform, offer, or claim to perform lead-based paint activities, as defined in this... 1, 2000. (c) All lead-based paint activities shall be performed pursuant to the work practice...

  9. Fabrication of a dye-doped liquid crystal light shutter by thermal curing of polymer

    NASA Astrophysics Data System (ADS)

    Yu, Byeong-Hun; Ji, Seong-Min; Kim, Jin-Hun; Huh, Jae-Won; Yoon, Tae-Hoon

    2017-07-01

    We report a thermal curing method for fabrication of a dye-doped polymer-stabilized liquid crystal (PSLC) light shutter, which can prevent the decrease in absorption and discoloration of the dye caused by the UV curing process. We found that the measured transmittance in the opaque state of a dye-doped PSLC cell fabricated by thermal curing was approximately 35% lower than that of a dye-doped PSLC cell fabricated by UV curing. Thermal curing can be an alternative approach for fabrication of a dye-doped PSLC light shutter which can be used to provide high visibility of a see-through display.

  10. 24 CFR 1006.375 - Other Federal requirements.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Federal requirements. (a) Lead-based paint. The following subparts of HUD's lead-based paint regulations at part 35, which implement the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4822-4846) and the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), apply to the use...

  11. 24 CFR 965.215 - Lead-based paint liability insurance coverage.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Lead-based paint liability... Insurance Coverage § 965.215 Lead-based paint liability insurance coverage. (a) General. The purpose of this... with lead-based paint activities that the PHA undertakes, in accordance with the PHA's ACC with HUD...

  12. 24 CFR 35.825 - Ongoing lead-based paint maintenance and reevaluation.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES HUD-Owned and Mortgagee-in-Possession Multifamily Property § 35.825 Ongoing lead-based paint...

  13. 48 CFR 1452.236-70 - Prohibition Against Use of Lead-based Paint.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Lead-based Paint. 1452.236-70 Section 1452.236-70 Federal Acquisition Regulations System DEPARTMENT OF... Clauses 1452.236-70 Prohibition Against Use of Lead-based Paint. As prescribed in 1436.570(b), insert the following clause: Prohibition Against Use of Lead-Based Paint—Department of the Interior (JUL 1996) Paint...

  14. 24 CFR 35.825 - Ongoing lead-based paint maintenance and reevaluation.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES HUD-Owned and Mortgagee-in-Possession Multifamily Property § 35.825 Ongoing lead-based paint...

  15. 24 CFR 92.355 - Lead-based paint.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

  16. 13 CFR 120.173 - Lead-based paint.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 13 Business Credit and Assistance 1 2014-01-01 2014-01-01 false Lead-based paint. 120.173 Section... to All Business Loans Requirements Imposed Under Other Laws and Orders § 120.173 Lead-based paint. If loan proceeds are for the construction or rehabilitation of a residential structure, lead-based paint...

  17. 24 CFR 291.430 - Elimination of lead-based paint hazards.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 2 2014-04-01 2014-04-01 false Elimination of lead-based paint... Lease and Sale of HUD-Acquired Single Family Properties for the Homeless § 291.430 Elimination of lead-based paint hazards. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the...

  18. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  19. 48 CFR 1452.236-70 - Prohibition Against Use of Lead-based Paint.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Lead-based Paint. 1452.236-70 Section 1452.236-70 Federal Acquisition Regulations System DEPARTMENT OF... Clauses 1452.236-70 Prohibition Against Use of Lead-based Paint. As prescribed in 1436.570(b), insert the following clause: Prohibition Against Use of Lead-Based Paint—Department of the Interior (JUL 1996) Paint...

  20. 24 CFR 35.935 - Ongoing lead-based paint maintenance activities.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Rehabilitation § 35.935 Ongoing lead-based paint maintenance activities. In the case of a rental... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Ongoing lead-based paint...

  1. 24 CFR 35.170 - Noncompliance with the requirements of subparts B through R of this part.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs... who informs a potential purchaser or occupant of lead-based paint or possible lead-based paint hazards...

  2. 24 CFR 35.935 - Ongoing lead-based paint maintenance activities.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Rehabilitation § 35.935 Ongoing lead-based paint maintenance activities. In the case of a rental... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Ongoing lead-based paint...

  3. 24 CFR 35.125 - Notice of evaluation and hazard reduction activities.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.125 Notice of... is undertaken and lead-based paint or lead-based paint hazards are found to be present, or if a...

  4. 24 CFR 35.935 - Ongoing lead-based paint maintenance activities.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Rehabilitation § 35.935 Ongoing lead-based paint maintenance activities. In the case of a rental... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Ongoing lead-based paint...

  5. 24 CFR 35.125 - Notice of evaluation and hazard reduction activities.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.125 Notice of... is undertaken and lead-based paint or lead-based paint hazards are found to be present, or if a...

  6. 24 CFR 35.1355 - Ongoing lead-based paint maintenance and reevaluation activities.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Ongoing lead-based paint...

  7. 40 CFR 745.325 - Lead-based paint activities: State and Tribal program requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES State and Indian Tribal Programs § 745.325 Lead-based paint activities: State and... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Lead-based paint activities: State and...

  8. 24 CFR 35.935 - Ongoing lead-based paint maintenance activities.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Rehabilitation § 35.935 Ongoing lead-based paint maintenance activities. In the case of a rental... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Ongoing lead-based paint...

  9. 40 CFR 745.325 - Lead-based paint activities: State and Tribal program requirements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES State and Indian Tribal Programs § 745.325 Lead-based paint activities: State and... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Lead-based paint activities: State and...

  10. 40 CFR 63.11177 - What records must I keep?

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ....11175 and copies of any report submitted as required by § 63.11176. (e) Records of paint strippers containing MeCl used for paint stripping operations, including the MeCl content of the paint stripper used. Documentation needs to be sufficient to verify annual usage of paint strippers containing MeCl (e.g., material...

  11. 40 CFR 63.11177 - What records must I keep?

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ....11175 and copies of any report submitted as required by § 63.11176. (e) Records of paint strippers containing MeCl used for paint stripping operations, including the MeCl content of the paint stripper used. Documentation needs to be sufficient to verify annual usage of paint strippers containing MeCl (e.g., material...

  12. 24 CFR 35.94 - Agent responsibilities.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Disclosure of Known Lead-Based Paint and/or Lead-Based Paint Hazards Upon Sale or Lease of Residential Property § 35.94 Agent... for the failure to disclose to a purchaser or lessee the presence of lead-based paint and/or lead...

  13. 24 CFR 291.430 - Elimination of lead-based paint hazards.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Lease and Sale of HUD-Acquired Single Family Properties for the Homeless § 291.430 Elimination of lead-based paint hazards. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Elimination of lead-based paint...

  14. Operational test of micro-oven for 48Ca beam

    NASA Astrophysics Data System (ADS)

    Ozeki, K.; Kageyama, T.; Kidera, M.; Higurashi, Y.; Nakagawa, T.

    2014-02-01

    In order to supply a high-intensity and stable 48Ca beam from the RIKEN 18-GHz electron cyclotron resonance ion source, we are conducting operational tests of a micro-oven. A mixture of CaO and Al powders is placed into the crucible of the micro-oven and heated to produce metallic calcium by a reductive reaction. The successful production of a calcium beam was confirmed. In addition, we reduced the material consumption rate by using a so-called "hot liner," and we enhanced the beam intensity by applying a negative voltage bias to the micro-oven, the effect of which is similar to the effect of a "biased disk."

  15. 24 CFR 35.100 - Purpose and applicability.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint... requirements of subparts B through R of this part are promulgated to implement the Lead-Based Paint Poisoning Prevention Act, as amended (42 U.S.C. 4821 et seq.), and the Residential Lead-Based Paint Hazard Reduction...

  16. 40 CFR 745.238 - Fees for accreditation and certification of lead-based paint activities.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... certification of lead-based paint activities. 745.238 Section 745.238 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.238 Fees for accreditation and certification of lead...

  17. 24 CFR 35.100 - Purpose and applicability.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint... requirements of subparts B through R of this part are promulgated to implement the Lead-Based Paint Poisoning Prevention Act, as amended (42 U.S.C. 4821 et seq.), and the Residential Lead-Based Paint Hazard Reduction...

  18. 29 CFR 1915.33 - Chemical paint and preservative removers.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 7 2013-07-01 2013-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

  19. 24 CFR 35.1220 - Ongoing lead-based paint maintenance activities.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Tenant-Based Rental Assistance § 35.1220 Ongoing lead-based paint maintenance activities...

  20. 24 CFR 570.608 - Lead-based paint.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Lead-based paint. 570.608 Section... DEVELOPMENT COMMUNITY FACILITIES COMMUNITY DEVELOPMENT BLOCK GRANTS Other Program Requirements § 570.608 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead...

  1. 48 CFR 1436.570 - Prohibition against use of lead-based paint.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... lead-based paint. 1436.570 Section 1436.570 Federal Acquisition Regulations System DEPARTMENT OF THE... 1436.570 Prohibition against use of lead-based paint. (a) Definitions. As used in this section... of Lead-Based Paint, in solicitations and contracts when construction of residential structures or...

  2. 48 CFR 1436.570 - Prohibition against use of lead-based paint.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... lead-based paint. 1436.570 Section 1436.570 Federal Acquisition Regulations System DEPARTMENT OF THE... 1436.570 Prohibition against use of lead-based paint. (a) Definitions. As used in this section... of Lead-Based Paint, in solicitations and contracts when construction of residential structures or...

  3. 40 CFR 745.223 - Definitions.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    .... Abatement means any measure or set of measures designed to permanently eliminate lead-based paint hazards... elimination of lead-based paint hazards; or (B) Are designed to permanently eliminate lead-based paint hazards..., when such activities are not designed to permanently eliminate lead-based paint hazards, but, instead...

  4. 29 CFR 1915.33 - Chemical paint and preservative removers.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

  5. 24 CFR 35.1340 - Clearance.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... abatement of lead-based paint or lead-based paint hazards shall be performed in accordance with 40 CFR 745...

  6. 40 CFR 745.61 - Scope and applicability.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Hazards § 745.61 Scope and applicability. (a) This subpart identifies lead-based paint hazards. (b) The standards for lead-based paint hazards apply to target housing and child-occupied facilities. (c) Nothing in...

  7. 24 CFR 35.1340 - Clearance.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... abatement of lead-based paint or lead-based paint hazards shall be performed in accordance with 40 CFR 745...

  8. 24 CFR 570.608 - Lead-based paint.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Lead-based paint. 570.608 Section... DEVELOPMENT COMMUNITY FACILITIES COMMUNITY DEVELOPMENT BLOCK GRANTS Other Program Requirements § 570.608 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead...

  9. 40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

  10. 40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

  11. 40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

  12. 40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

  13. Effect of UV curing time on physical and electrical properties and reliability of low dielectric constant materials

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kao, Kai-Chieh; Cheng, Yi-Lung, E-mail: yjcheng@ncnu.edu.tw; Chang, Wei-Yuan

    2014-11-01

    This study comprehensively investigates the effect of ultraviolet (UV) curing time on the physical, electrical, and reliability characteristics of porous low-k materials. Following UV irradiation for various periods, the depth profiles of the chemical composition in the low-k dielectrics were homogeneous. Initially, the UV curing process preferentially removed porogen-related CH{sub x} groups and then modified Si-CH{sub 3} and cage Si-O bonds to form network Si-O bonds. The lowest dielectric constant (k value) was thus obtained at a UV curing time of 300 s. Additionally, UV irradiation made porogen-based low-k materials hydrophobic and to an extent that increased with UV curing time.more » With a short curing time (<300 s), porogen was not completely removed and the residues degraded reliability performance. A long curing time (>300 s) was associated with improved mechanical strength, electrical performance, and reliability of the low-k materials, but none of these increased linearly with UV curing time. Therefore, UV curing is necessary, but the process time must be optimized for porous low-k materials on back-end of line integration in 45 nm or below technology nodes.« less

  14. Cooked yields, color, tenderness, and sensory traits of beef roasts cooked in an oven with steam generation versus a commercial convection oven to different endpoint temperatures.

    PubMed

    Bowers, L J; Dikeman, M E; Murray, L; Stroda, S L

    2012-10-01

    A CVap steam generation oven was compared with a Blodgett convection oven to examine effects on yields, cooked color, tenderness, and sensory traits of beef Longissimus lumborum (LL), Deep pectoralis (DP), and Biceps femoris (BF) muscles cooked to 1 of 3 temperatures (65.6, 71.1, or 76.7°C). Four roasts were cooked in the CVap for a constant time, and 2 roasts were cooked in the Blodgett until they reached target temperatures (3 replications). Cooking yields were higher (P<0.05) for BF and LL roasts in the CVap. Slice shear force (SSF) for BF roasts was lowest (P<0.05) in the CVap but lowest (P<0.05) for DP roasts in the Blodgett. No oven effect (P>0.05) was found for LL roasts. Sensory tenderness for BF roasts in the CVap was higher (P<0.05) than those in the Blodgett. Juiciness was higher (P<0.05) for LL roasts in the Blodgett. The CVap oven offers some tenderization (BF) and cooking yield advantages (BF and DP) over forced-air convection cooking. Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. 40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

  16. Evaluation of yellow-white paint mixtures.

    DOT National Transportation Integrated Search

    1980-01-01

    In view of the potential cost savings to be achieved through the use of the regular yellow traffic paint diluted with less expensive white paint, it was decided that the Department would evaluate roadway applications of the paint mixture with emphasi...

  17. Process for making photovoltaic devices and resultant product

    DOEpatents

    Foote, James B.; Kaake, Steven A. F.; Meyers, Peter V.; Nolan, James F.

    1996-07-16

    A process and apparatus (70) for making a large area photovoltaic device (22) that is capable of generating low cost electrical power. The apparatus (70) for performing the process includes an enclosure (126) providing a controlled environment in which an oven (156) is located. At least one and preferably a plurality of deposition stations (74,76,78) provide heated vapors of semiconductor material within the oven (156) for continuous elevated temperature deposition of semiconductor material on a sheet substrate (24) including a glass sheet (26) conveyed within the oven. The sheet substrate (24) is conveyed on a roller conveyor (184) within the oven (156) and the semiconductor material whose main layer (82) is cadmium telluride is deposited on an upwardly facing surface (28) of the substrate by each deposition station from a location within the oven above the roller conveyor. A cooling station (86) rapidly cools the substrate (24) after deposition of the semiconductor material thereon to strengthen the glass sheet of the substrate.

  18. 21 CFR 170.60 - Nitrites and/or nitrates in curing premixes.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Nitrites and/or nitrates in curing premixes. 170... and Decisions § 170.60 Nitrites and/or nitrates in curing premixes. (a) Nitrites and/or nitrates are.... (b) Nitrites and/or nitrates, when packaged separately from flavoring and seasoning in curing...

  19. 21 CFR 170.60 - Nitrites and/or nitrates in curing premixes.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Nitrites and/or nitrates in curing premixes. 170... and Decisions § 170.60 Nitrites and/or nitrates in curing premixes. (a) Nitrites and/or nitrates are.... (b) Nitrites and/or nitrates, when packaged separately from flavoring and seasoning in curing...

  20. Total tin and organotin speciation in historic layers of antifouling paint on leisure boat hulls.

    PubMed

    Lagerström, Maria; Strand, Jakob; Eklund, Britta; Ytreberg, Erik

    2017-01-01

    Despite their ban on small vessels in 1989 in the EU, organotin compounds (OTCs) are still being released into the environment due to their presence in historic paint layers on leisure boats. 23 paint samples scraped from recreational boats from three countries around the Baltic Sea were analyzed for total tin (Sn) and OTCs. Two antifouling paint products were also subjected to the same analyses. A new method for the detection of Sn in paint flake samples was developed and found to yield more accurate results compared to four different acid digestion methods. A new method was also developed for the extraction of OTCs from ground paint flakes. This endeavor revealed that existing methods for organotin analysis of sediment may not have full recoveries of OTCs if paint flakes are present in the sample. The hull paint samples had Sn concentrations ranging from 25 to 18,000 mg/kg paint and results showed that tributyltin (TBT) was detected in all samples with concentrations as high as 4.7 g (as Sn)/kg paint. TBT was however not always the major OTC. Triphenyltin (TPhT) was abundant in many samples, especially in those originating from Finland. Several other compounds such as monobutyltin (MBT), dibutyltin (DBT), tetrabutyltin (TeBT), monophenyltin (MPhT) and diphenyltin (DPhT) were also detected. These could be the result of degradation occurring on the hull or of impurities in the paint products as they were also identified in the two analyzed paint products. A linear correlation (r 2  = 0.934) was found between the total tin content and the sum of all detected OTCs. The detection of tin can therefore be used to indicate the presence of OTCs on leisure boats. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  1. Evaluation of interior and exterior latex paints : final report.

    DOT National Transportation Integrated Search

    1979-10-01

    The wood panels that have only one coat of paint over bare wood and one coat of paint over primed wood are continuing to show sighs of deterioration. The wood panels that have two coats of paint over bare wood and two coats of paint over primed wood ...

  2. 24 CFR 92.355 - Lead-based paint.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

  3. 24 CFR 291.430 - Elimination of lead-based paint hazards.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 2 2011-04-01 2011-04-01 false Elimination of lead-based paint... Lease and Sale of HUD-Acquired Single Family Properties for the Homeless § 291.430 Elimination of lead-based paint hazards. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the...

  4. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  5. 24 CFR 965.215 - Lead-based paint liability insurance coverage.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Lead-based paint liability... Insurance Coverage § 965.215 Lead-based paint liability insurance coverage. (a) General. The purpose of this... with lead-based paint activities that the PHA undertakes, in accordance with the PHA's ACC with HUD...

  6. 13 CFR 120.173 - Lead-based paint.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 13 Business Credit and Assistance 1 2013-01-01 2013-01-01 false Lead-based paint. 120.173 Section... to All Business Loans Requirements Imposed Under Other Laws and Orders § 120.173 Lead-based paint. If loan proceeds are for the construction or rehabilitation of a residential structure, lead-based paint...

  7. 24 CFR 291.430 - Elimination of lead-based paint hazards.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 2 2013-04-01 2013-04-01 false Elimination of lead-based paint... Lease and Sale of HUD-Acquired Single Family Properties for the Homeless § 291.430 Elimination of lead-based paint hazards. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the...

  8. 24 CFR 92.355 - Lead-based paint.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

  9. 40 CFR 745.325 - Lead-based paint activities: State and Tribal program requirements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES State and Indian Tribal Programs § 745.325 Lead-based paint activities: State and... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Lead-based paint activities: State and...

  10. 40 CFR 745.229 - Certification of individuals and firms engaged in lead-based paint activities: public and...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.229 Certification of individuals and firms engaged in lead-based... engaged in lead-based paint activities: public and commercial buildings, bridges and superstructures...

  11. 24 CFR 35.170 - Noncompliance with the requirements of subparts B through R of this part.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs... who informs a potential purchaser or occupant of lead-based paint or possible lead-based paint hazards...

  12. 40 CFR 745.229 - Certification of individuals and firms engaged in lead-based paint activities: public and...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.229 Certification of individuals and firms engaged in lead-based... engaged in lead-based paint activities: public and commercial buildings, bridges and superstructures...

  13. CHARACTERIZATION OF EMISSIONS OF VOLATILE ORGANIC COMPOUNDS FROM INTERIOR ALKYD PAINT

    EPA Science Inventory

    Alkyd paint continues to be used indoors for application to wood trim, cabinet surfaces, and some kitchen and bathroom walls. Paint may represent a significant source of volatile organic compounds (VOCs) indoors depending on the frequency of use and amount of surface paint. The U...

  14. 24 CFR 35.825 - Ongoing lead-based paint maintenance and reevaluation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES HUD-Owned and Mortgagee-in-Possession Multifamily Property § 35.825 Ongoing lead-based paint...

  15. 24 CFR 965.215 - Lead-based paint liability insurance coverage.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Lead-based paint liability... Insurance Coverage § 965.215 Lead-based paint liability insurance coverage. (a) General. The purpose of this... with lead-based paint activities that the PHA undertakes, in accordance with the PHA's ACC with HUD...

  16. Effectiveness of oxygen barrier oven bags in low temperature cooking on reduction of warmed-over flavor in beef roasts.

    PubMed

    Lepper-Blilie, A N; Berg, E P; Buchanan, D S; Keller, W L; Maddock-Carlin, K R; Berg, P T

    2014-03-01

    A 3×3×2 factorial was utilized to determine if roast size (small, medium, large), cooking method (open-pan, oven bag, vacuum bag), and heating process (fresh, reheated) prevented warmed-over flavor (WOF) in beef clod roasts. Fresh vacuum bag and reheated open-pan roasts had higher cardboardy flavor scores compared with fresh open-pan roast scores. Reheated roasts in oven and vacuum bags did not differ from fresh roasts for cardboardy flavor. Brothy and fat intensity were increased in reheated roasts in oven and vacuum bags compared with fresh roasts in oven and vacuum bags. Differences in TBARS were found in the interaction of heating process and roast size with the fresh and reheated large, and reheated medium roasts having the lowest values. Based on TBARS data, to prevent WOF in reheated beef roasts, a larger size roast in a cooking bag is the most effective method. Copyright © 2013 Elsevier Ltd. All rights reserved.

  17. 77 FR 20612 - National Tree-Marking Paint Committee Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-05

    ... DEPARTMENT OF AGRICULTURE Forest Service National Tree-Marking Paint Committee Meeting AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The National Tree-Marking Paint Committee will... related to improvements in, concerns about, and the handling and use of tree-marking paint by personnel of...

  18. 24 CFR 35.100 - Purpose and applicability.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint... requirements of subparts B through R of this part are promulgated to implement the Lead-Based Paint Poisoning Prevention Act, as amended (42 U.S.C. 4821 et seq.), and the Residential Lead-Based Paint Hazard Reduction...

  19. 40 CFR 745.238 - Fees for accreditation and certification of lead-based paint activities.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... certification of lead-based paint activities. 745.238 Section 745.238 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.238 Fees for accreditation and certification of lead...

  20. Process development and monitoring in stripping of a highly transparent polymeric paint with ns-pulsed fiber laser

    NASA Astrophysics Data System (ADS)

    Jasim, Halah A.; Demir, Ali Gökhan; Previtali, Barbara; Taha, Ziad A.

    2017-08-01

    Laser paint removal was studied with ns-pulsed fiber laser on the combination of 20 μm-thick, white polymeric paint and Al alloy substrate. The response of paint to single pulse ablation was evaluated to measure the ablated zone dimensions. With this information, the effect of overlap, number of passes and pulse repetition rate was evaluated to investigate machining depth. Optical emission spectroscopy was used to investigate the machining behaviour as well as to propose monitoring strategies. The results showed that despite the high transparency of the paint, complete paint removal can be achieved with reduced substrate damage (Sa = 1.3 μm). The emission spectroscopy can be used to identify removal completion as well as the reach of substrate material. The observations were also used to explain a paint removal mechanism based on thermal expansion of the paint and mechanical action provided by the plasma expansion from the substrate material.

  1. Development of a high-temperature oven for the 28 GHz electron cyclotron resonance ion source.

    PubMed

    Ohnishi, J; Higurashi, Y; Kidera, M; Ozeki, K; Nakagawa, T

    2014-02-01

    We have been developing the 28 GHz ECR ion source in order to accelerate high-intensity uranium beams at the RIKEN RI-beam Factory. Although we have generated U(35+) beams by the sputtering method thus far, we began developing a high-temperature oven with the aim of increasing and stabilizing the beams. Because the oven method uses UO2, a crucible must be heated to a temperature higher than 2000 °C to supply an appropriate amount of UO2 vapor to the ECR plasma. Our high-temperature oven uses a tungsten crucible joule-heated with DC current of approximately 450 A. Its inside dimensions are ϕ11 mm × 13.5 mm. Since the crucible is placed in a magnetic field of approximately 3 T, it is subject to a magnetic force of approximately 40 N. Therefore, we used ANSYS to carefully design the crucible, which was manufactured by machining a tungsten rod. We could raise the oven up to 1900 °C in the first off-line test. Subsequently, UO2 was loaded into the crucible, and the oven was installed in the 28 GHz ECR ion source and was tested. As a result, a U(35+) beam current of 150 μA was extracted successfully at a RF power of approximately 3 kW.

  2. 46 CFR 111.105-43 - Paint stowage or mixing spaces.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Paint stowage or mixing spaces. 111.105-43 Section 111... ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Hazardous Locations § 111.105-43 Paint stowage or mixing spaces. A space for the stowage or mixing of paint must not have any electric equipment, except: (a) Intrinsically...

  3. 40 CFR 745.220 - Scope and applicability.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint... accreditation of training programs for lead-based paint activities and renovations, procedures and requirements for the certification of individuals and firms engaged in lead-based paint activities, and work...

  4. Disinfection of Wastewater by Microwaves.

    DTIC Science & Technology

    1980-01-01

    used. Thermophilic B. stearothermophilus cells were used to try to determine if the mechanism of destruction was thermal. The microwave oven was set at...curve for E. coli B cells heated in a microwave oven temperature programed for 600 C ...... ............ 8 7. Survivor curve for B. stearothermophilus ...ATCC 12980 cells heated in a microwave oven temperature programed for 600 C. 98. Survivor curve for B. stearothermophilus AICC 12980 ........ 9 9

  5. RIGGERS LOFT/PAINT SHOP/SHEET METAL SHOP, VIEW TO SOUTHEAST. THE PAINT ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    RIGGERS LOFT/PAINT SHOP/SHEET METAL SHOP, VIEW TO SOUTHEAST. THE PAINT SHOP WAS LOCATED IN THE CLOSEST CORNER OF THE BUILDING. THE SHEET METAL SHOP WAS LOCATED IN THE CORNER OF THE BUILDING ON THE RIGHT. THE RIGGERS LOFT WAS LOCATED IN THE PORTION OF THE BUILDING OUT OF VIEW TO THE LEFT - Rosie the Riveter National Historical Park, Riggers Loft/Paint Shop/Sheet Metal Shop, 1322 Canal Boulevard, Richmond, Contra Costa County, CA

  6. A novel reverse osmosis membrane modified by polyvinyl alcohol with maleic anhydride crosslinking

    NASA Astrophysics Data System (ADS)

    Samnani, Mohit; Rathod, Harshad; Raval, Hiren

    2018-03-01

    In the era of increasing energy crisis, it is inevitable to decrease process energy consumption to increase process viability and curtail green-house gas emission. The Reverse Osmosis plant requires significant energy to transfer water overcoming the osmotic pressure. This paper focuses on increasing the water flux for Thin Film Composite Reverse Osmosis (TFC RO) membrane without compromising salt rejection performance leading to the environmentally friendly and economically attractive process. The virgin TFC RO membrane was exposed to solution of sodium hypochlorite of concentration 2000 mg l-1 for 1 h to activate the surface of the membrane, followed by the treatment with the mixture of polyvinyl alcohol and maleic anhydride with varying concentrations for 1 h and curing in the oven at 80 °C temperature for 10 min. Out of all the treated membranes, the membrane treated with 2000 mg l-1 polyvinyl alcohol and 1000 mg l-1 maleic anhydride demonstrated the highest salt rejection of 96.83 % with 2% increase as compared to the virgin TFC RO membrane. The water flux of the membrane was around 44% higher than the virgin TFC RO membrane. The membrane samples were characterized by atomic force micrographs, ATR-FTIR, Nuclear magnetic resonance and Dynamic mechanical analysis.

  7. Evaluation of Sandwich Structure Bonding In Out-of-Autoclave Processing

    NASA Technical Reports Server (NTRS)

    Hou, Tan-Hung; Baughman, James M.; Zimmerman, Thomas J.; Sutter, James K.; Gardner, John M.

    2010-01-01

    The out-of-autoclave-vacuum-bag-only (OOA-VBO) process is low in capital expenditures compared to the traditional autoclave, however, the material challenges for OOA-VBO workable material systems are high. Presently there are few such aerospace grade prepreg materials available commercially. In this study, we evaluated processing and properties of honeycomb sandwich structure (HC/SS) panels fabricated by co-curing composite face sheet with adhesives by the OOA-VBO process in an oven. The prepreg materials were IM7/MTM 45-1 and T40-800B/5320. Adhesives studied were AF-555M, XMTA-241/PM15, FM-309-1M and FM-300K. Aluminum H/C cores with and without perforations were included. It was found that adhesives in IM7/MTM 45-1/AF-555M, T40-800B/5320/FM 309-1M and T40-800B/5320/FM-300K panels all foamed but yielded high flatwise tensile (FWT) strength values above 8,275 kPA (1,200 psi). IM7/MTM 45-1/XMTA-241/PM15 did not foam, yet yielded a low FWT strength. SEM photomicrographs revealed that the origin of this low strength was poor adhesion in the interfaces between the adhesive and face sheet composite due to poor wetting associated with the high initial viscosity of the XMTA-241/PM15 adhesive.

  8. Calibration and standardization of microwave ovens for fixation of brain and peripheral nerve tissue.

    PubMed

    Login, G R; Leonard, J B; Dvorak, A M

    1998-06-01

    Rapid and reproducible fixation of brain and peripheral nerve tissue for light and electron microscopy studies can be done in a microwave oven. In this review we report a standardized nomenclature for diverse fixation techniques that use microwave heating: (1) microwave stabilization, (2) fast and ultrafast primary microwave-chemical fixation, (3) microwave irradiation followed by chemical fixation, (4) primary chemical fixation followed by microwave irradiation, and (5) microwave fixation used in various combinations with freeze fixation. All of these methods are well suited to fix brain tissue for light microscopy. Fast primary microwave-chemical fixation is best for immunoelectron microscopy studies. We also review how the physical characteristics of the microwave frequency and the dimensions of microwave oven cavities can compromise microwave fixation results. A microwave oven can be calibrated for fixation when the following parameters are standardized: irradiation time; water load volume, initial temperature, and placement within the oven; fixative composition, volume, and initial temperature; and specimen container shape and placement within the oven. Using two recently developed calibration tools, the neon bulb array and the agar-saline-Giemsa tissue phantom, we report a simple calibration protocol that identifies regions within a microwave oven for uniform microwave fixation. Copyright 1998 Academic Press.

  9. Investigation of automotive primer and basecoat paint surface's adhesion by solid particle erosion

    NASA Astrophysics Data System (ADS)

    Demirci, M.; Baǧcı, M.

    2018-05-01

    Millions of cars are sold around the world and tons of paint are used for these cars. Since the car paint industry is alive in this way, new developments in the paint sector have been taking place every day. It is important to determine how these developments affect paint erosion. Solid particle erosion wear is a subject that keeps its update for car paints and it always needs to be investigated in detail. The target of this experimental study is to investigate solid particle erosion behavior of a commercial acrylic/melamine primer surface and basecoat of automotive paint. As a erodent, silica particles having a weight of 1 to 5 kg were used. Tests were performed at 30° and 90° impact angle and particle velocity 23 m s-1. With this work, an idea about the adhesion of the car paint coatings to the material surface was obtained.

  10. Automated Laser Paint Stripping (ALPS) update

    NASA Astrophysics Data System (ADS)

    Lovoi, Paul

    1993-03-01

    To date, the DoD has played a major role in funding a number of paint stripping programs. Some technologies have proven less effective than contemplated. Others are still in the validation phase. Paint stripping is one of the hottest issues being addressed by the finishing industry since the Environmental Protection Agency (EPA) has mandated that chemical stripping using methylene chloride/phenolic type strippers be stopped. The DoD and commercial aircraft companies are hard-pressed to find an alternative. Automated laser paint stripping has been identified as a technique for removing coatings from aircraft surfaces. International Technical Associates (InTA) was awarded a Navy contract for an automated laser paint stripping system (ALPS) that will remove paint from metallic and composite substrates. For the program, which will validate laser paint stripping, InTA will design, build, test, and install a system for fighter-sized aircraft at both the Norfolk and North Island (San Diego) Aviation Depots.

  11. 78 FR 20295 - National Tree-Marking Paint Committee Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-04

    ... Tree-Marking Paint Committee Meeting AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The National Tree-Marking Paint Committee will meet in Awendaw, SC on May 21-23, 2013. The purpose of... use of tree-marking paint by personnel of the Forest Service and the Department of the Interior...

  12. 24 CFR 1006.375 - Other Federal requirements.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Federal requirements. (a) Lead-based paint. The following subparts of HUD's lead-based paint regulations at part 35, which implement the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4822-4846) and the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), apply to the use...

  13. 40 CFR 446.10 - Applicability; description of the oil-base solvent wash paint subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-base solvent wash paint subcategory. 446.10 Section 446.10 Protection of Environment ENVIRONMENTAL...-Base Solvent Wash Paint Subcategory § 446.10 Applicability; description of the oil-base solvent wash... production of oil-base paint where the tank cleaning is performed using solvents. When a plant is subject to...

  14. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  15. 48 CFR 1452.236-70 - Prohibition Against Use of Lead-based Paint.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Lead-based Paint. 1452.236-70 Section 1452.236-70 Federal Acquisition Regulations System DEPARTMENT OF... Clauses 1452.236-70 Prohibition Against Use of Lead-based Paint. As prescribed in 1436.570(b), insert the following clause: Prohibition Against Use of Lead-Based Paint—Department of the Interior (JUL 1996) Paint...

  16. 24 CFR 92.355 - Lead-based paint.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

  17. 24 CFR 291.430 - Elimination of lead-based paint hazards.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 2 2012-04-01 2012-04-01 false Elimination of lead-based paint... Lease and Sale of HUD-Acquired Single Family Properties for the Homeless § 291.430 Elimination of lead-based paint hazards. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the...

  18. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 4 2013-04-01 2013-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  19. 48 CFR 1452.236-70 - Prohibition Against Use of Lead-based Paint.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Lead-based Paint. 1452.236-70 Section 1452.236-70 Federal Acquisition Regulations System DEPARTMENT OF... Clauses 1452.236-70 Prohibition Against Use of Lead-based Paint. As prescribed in 1436.570(b), insert the following clause: Prohibition Against Use of Lead-Based Paint—Department of the Interior (JUL 1996) Paint...

  20. 24 CFR 965.215 - Lead-based paint liability insurance coverage.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Lead-based paint liability... Insurance Coverage § 965.215 Lead-based paint liability insurance coverage. (a) General. The purpose of this... with lead-based paint activities that the PHA undertakes, in accordance with the PHA's ACC with HUD...

  1. 40 CFR 63.11177 - What records must I keep?

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ....11175 and copies of any report submitted as required by § 63.11176. (e) Records of paint strippers containing MeCl used for paint stripping operations, including the MeCl content of the paint stripper used. Documentation needs to be sufficient to verify annual usage of paint strippers containing MeCl (e.g., material...

  2. 24 CFR 35.1355 - Ongoing lead-based paint maintenance and reevaluation activities.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Ongoing lead-based paint...

  3. 24 CFR 35.1355 - Ongoing lead-based paint maintenance and reevaluation activities.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Ongoing lead-based paint...

  4. 24 CFR 35.170 - Noncompliance with the requirements of subparts B through R of this part.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs... who informs a potential purchaser or occupant of lead-based paint or possible lead-based paint hazards...

  5. 40 CFR 745.325 - Lead-based paint activities: State and Tribal program requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES State and Indian Tribal Programs § 745.325 Lead-based paint activities: State and... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Lead-based paint activities: State and...

  6. 24 CFR 35.1355 - Ongoing lead-based paint maintenance and reevaluation activities.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Ongoing lead-based paint...

  7. 24 CFR 35.170 - Noncompliance with the requirements of subparts B through R of this part.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs... who informs a potential purchaser or occupant of lead-based paint or possible lead-based paint hazards...

  8. 24 CFR 92.355 - Lead-based paint.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

  9. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

  10. Analysis of curing process and thermal properties of phenol-urea-formaldehyde cocondensed resins

    Treesearch

    Bunchiro Tomita; Masahiko Ohyama; Atsushi Itoh; Kiyoto Doi; Chung-Yun Hse

    1994-01-01

    The curing processes of resols, urea-formaldehyde (UF) resins, their mechanical blends, and phenol-urea cocondensed resins, as well as the reaction of 2,4,6-trimethylolphenol with urea were investiiated with the torsional braid analysis method. The thermal stabilities of these resins after curing also were compared. The results were as follows: (1) In the curing...

  11. 40 CFR 745.239 - Effective dates.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities... or firm shall perform, offer, or claim to perform lead-based paint activities, as defined in this... 1, 2000. (c) All lead-based paint activities shall be performed pursuant to the work practice...

  12. Laser effects based optimal laser parameter identifications for paint removal from metal substrate at 1064 nm: a multi-pulse model

    NASA Astrophysics Data System (ADS)

    Han, Jinghua; Cui, Xudong; Wang, Sha; Feng, Guoying; Deng, Guoliang; Hu, Ruifeng

    2017-10-01

    Paint removal by laser ablation is favoured among cleaning techniques due to its high efficiency. How to predict the optimal laser parameters without producing damage to substrate still remains challenging for accurate paint stripping. On the basis of ablation morphologies and combining experiments with numerical modelling, the underlying mechanisms and the optimal conditions for paint removal by laser ablation are thoroughly investigated. Our studies suggest that laser paint removal is dominated by the laser vaporization effect, thermal stress effect and laser plasma effect, in which thermal stress effect is the most favoured while laser plasma effect should be avoided during removal operations. Based on the thermodynamic equations, we numerically evaluated the spatial distribution of the temperature as well as thermal stress in the paint and substrate under the irradiation of laser pulse at 1064 nm. The obtained curves of the paint thickness vs. threshold fluences can provide the reference standard of laser parameter selection in view of the paint layer with different thickness. A multi-pulse model is proposed and validated under a constant laser fluence to perfectly remove a thicker paint layer. The investigations and the methods proposed here might give hints to the efficient operations on the paint removal and lowering the risk of substrate damages.

  13. Fiber Bragg grating sensor to monitor stress kinetics in drying process of commercial latex paints.

    PubMed

    de Lourenço, Ivo; Possetti, Gustavo R C; Muller, Marcia; Fabris, José L

    2010-01-01

    In this paper, we report a study about the application of packaged fiber Bragg gratings used as strain sensors to monitor the stress kinetics during the drying process of commercial latex paints. Three stages of drying with distinct mechanical deformation and temporal behaviors were identified for the samples, with mechanical deformation from 15 μm to 21 μm in the longitudinal film dimension on time intervals from 370 to 600 minutes. Drying time tests based on human sense technique described by the Brazilian Technical Standards NBR 9558 were also done. The results obtained shows that human sense technique has a limited perception of the drying process and that the optical measurement system proposed can be used to characterize correctly the dry-through stage of paint. The influence of solvent (water) addition in the drying process was also investigated. The paint was diluted with four parts paint and one part water (80% paint), and one part paint and one part water (50% paint). It was observed that the increase of the water ratio mixed into the paint decreases both the mechanical deformation magnitude and the paint dry-through time. Contraction of 5.2 μm and 10.4 μm were measured for concentrations of 50% and 80% of paint in the mixture, respectively. For both diluted paints the dry-through time was approximately 170 minutes less than undiluted paint. The optical technique proposed in this work can contribute to the development of new standards to specify the drying time of paint coatings.

  14. Fiber Bragg Grating Sensor to Monitor Stress Kinetics in Drying Process of Commercial Latex Paints

    PubMed Central

    de Lourenço, Ivo; Possetti, Gustavo R. C.; Muller, Marcia; Fabris, José L.

    2010-01-01

    In this paper, we report a study about the application of packaged fiber Bragg gratings used as strain sensors to monitor the stress kinetics during the drying process of commercial latex paints. Three stages of drying with distinct mechanical deformation and temporal behaviors were identified for the samples, with mechanical deformation from 15 μm to 21 μm in the longitudinal film dimension on time intervals from 370 to 600 minutes. Drying time tests based on human sense technique described by the Brazilian Technical Standards NBR 9558 were also done. The results obtained shows that human sense technique has a limited perception of the drying process and that the optical measurement system proposed can be used to characterize correctly the dry-through stage of paint. The influence of solvent (water) addition in the drying process was also investigated. The paint was diluted with four parts paint and one part water (80% paint), and one part paint and one part water (50% paint). It was observed that the increase of the water ratio mixed into the paint decreases both the mechanical deformation magnitude and the paint dry-through time. Contraction of 5.2 μm and 10.4 μm were measured for concentrations of 50% and 80% of paint in the mixture, respectively. For both diluted paints the dry-through time was approximately 170 minutes less than undiluted paint. The optical technique proposed in this work can contribute to the development of new standards to specify the drying time of paint coatings. PMID:22399906

  15. Self-curing concrete with different self-curing agents

    NASA Astrophysics Data System (ADS)

    Gopala krishna sastry, K. V. S.; manoj kumar, Putturu

    2018-03-01

    Concrete is recognised as a versatile construction material globally. Properties of concrete depend upon, to a greater extent, the hydration of cement and microstructure of hydrated cement. Congenial atmosphere would aid the hydration of cement and hence curing of concrete becomes essential, till a major portion of the hydration process is completed. But in areas of water inadequacy and concreting works at considerable heights, curing is problematic. Self-Curing or Internal Curing technique overcomes these problems. It supplies redundant moisture, for more than sufficient hydration of cement and diminish self-desiccation. Self-Curing agents substantially help in the conservation of water in concrete, by bringing down the evaporation during the hydration of Concrete. The present study focuses on the impact of self-curing agents such as Poly Ethylene Glycol (PEG), Poly Vinyl Alcohol (PVA) and Super Absorbent Polymer (SAP) on the concrete mix of M25 grade (reference mix). The effect of these agents on strength properties of Concrete such as compressive strength, split tensile strength and flexural strength was observed on a comparative basis which revealed that PEG 4000 was the most effective among all the agents.

  16. Stripping Paint From Exterior Wood Surfaces

    Treesearch

    Mark T. Knaebe

    2013-01-01

    Removing paint and other film-forming finishes is a time consuming and often difficult process. In some cases, finishes need to be removed prior to repainting; for example, if the old surface is covered with severely peeled or blistered paint or if excessive paint buildup has caused cross-grain cracking. You must also remove the finish before applying a penetrating...

  17. Enhanced multifunctional paint for detection of radiation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Farmer, Joseph C.; Moses, Edward Ira; Rubenchik, Alexander M.

    An enhanced multifunctional paint apparatus, systems, and methods for detecting radiation on a surface include providing scintillation particles; providing an enhance neutron absorptive material; providing a binder; combining the scintillation particles, the enhance neutron absorptive material, and the binder creating a multifunctional paint; applying the multifunctional paint to the surface; and monitoring the surface for detecting radiation.

  18. 24 CFR 1000.40 - Do lead-based paint poisoning prevention requirements apply to affordable housing activities...

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... AMERICAN HOUSING ACTIVITIES General § 1000.40 Do lead-based paint poisoning prevention requirements apply..., subparts A, B, H, J, K, M and R of this title, which implement the Lead-Based Paint Poisoning Prevention... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Do lead-based paint poisoning...

  19. 40 CFR 745.223 - Definitions.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    .... Abatement means any measure or set of measures designed to permanently eliminate lead-based paint hazards... elimination of lead-based paint hazards; or (B) Are designed to permanently eliminate lead-based paint hazards..., when such activities are not designed to permanently eliminate lead-based paint hazards, but, instead...

  20. 24 CFR 570.461 - Post-preliminary approval requirements; lead-based paint.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... requirements; lead-based paint. 570.461 Section 570.461 Housing and Urban Development Regulations Relating to... GRANTS Urban Development Action Grants § 570.461 Post-preliminary approval requirements; lead-based paint. The recipient may receive preliminary approval prior to the accomplishment of lead-based paint...

Top