40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2012 CFR

2012-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2010 CFR

2010-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2013 CFR

2013-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2014 CFR

2014-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

40 CFR Appendix A to Subpart IIIi... - Determination of Capture Efficiency of Automobile and Light-Duty Truck Spray Booth Emissions From...

Code of Federal Regulations, 2011 CFR

2011-07-01

... coating, i. 2.5.1You must weigh the blank panel. (Same as in bake oven panel test.) The mass of the blank... spray booth zones being tested. (Different than bake oven panel test.) This weighing must be conducted... and before the bake oven where the coating applied to the panel is cured, 2.5.5.2All of the flash-off...

Exposures to 1,6-hexamethylene diisocyanate during polyurethane spray painting in the U.S. Air Force.

PubMed

Carlton, G N; England, E C

2000-09-01

1,6-Hexamethylene diisocyanate (HDI) exposures were measured during polyurethane enamel spray painting at four Air Force bases. Breathing zone samples were collected for HDI monomer and polyisocyanates (oligomers) using three sampling methods: NIOSH Method 5521, the Iso-Chek sampler, and the total aerosol mass method (TAMM). Exposures to HDI monomer are low when compared to current occupational exposure limits; the highest 8-hr time-weighted average (TWA) exposure found was 3.5 micrograms/m3, below the American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 34 micrograms/m3. HDI oligomer levels were higher; mean task exposures indicated by either the Iso-Chek sampler or TAMM are above the Oregon ceiling limit of 1 mg/m3. Eight-hour TWA exposures, however, were much lower, with only one exceeding the Oregon standard of 0.5 mg/m3. Poor worker practices commonly observed during this study included: standing in downwind positions so paint overspray passed through breathing zones; spraying toward other painters; and using excessive paint spray gun air cap pressures. Workers should stand in upwind orientation relative to the aircraft being painted, causing overspray to move away from the painter's breathing zone; adjust their position to prevent spraying other painters or limit paint application to one worker at a time; and use air cap pressure gauges prior to spraying to limit spray gun air cap pressures and reduce paint overspray generation rates. These improved techniques will result in reduced worker exposures to isocyanates.

29 CFR 1910.107 - Spray finishing using flammable and combustible materials.

Code of Federal Regulations, 2012 CFR

2012-07-01

... finishing material. (5) Dry spray booth. A spray booth not equipped with a water washing system as described in subparagraph (4) of this paragraph. A dry spray booth may be equipped with (i) distribution or... it enters the exhaust duct; or (ii) overspray dry filters to minimize dusts; or (iii) overspray dry...

29 CFR 1910.107 - Spray finishing using flammable and combustible materials.

Code of Federal Regulations, 2014 CFR

2014-07-01

... finishing material. (5) Dry spray booth. A spray booth not equipped with a water washing system as described in subparagraph (4) of this paragraph. A dry spray booth may be equipped with (i) distribution or... it enters the exhaust duct; or (ii) overspray dry filters to minimize dusts; or (iii) overspray dry...

29 CFR 1910.107 - Spray finishing using flammable and combustible materials.

Code of Federal Regulations, 2013 CFR

2013-07-01

... finishing material. (5) Dry spray booth. A spray booth not equipped with a water washing system as described in subparagraph (4) of this paragraph. A dry spray booth may be equipped with (i) distribution or... it enters the exhaust duct; or (ii) overspray dry filters to minimize dusts; or (iii) overspray dry...

Hazardous properties of paint residues from the furniture industry.

PubMed

Vaajasaari, Kati; Kulovaara, Maaret; Joutti, Anneli; Schultz, Eija; Soljamo, Kari

2004-01-30

The objective of this study was to screen nine excess paint residues for environmental hazard and to evaluate their disposability in a non-hazardous or hazardous-waste landfill. These residues were produced in the process of spray-painting furniture. Residues were classified according to their leaching and ecotoxicological properties. Leaching properties were determined with the European standard SFS-EN 12457-2 leaching-test. The toxicity of the leaching-test eluates was measured with plant-, bacteria- and enzyme-inhibition bioassays. Total organic carbon, formaldehyde and solvent concentrations in the solid wastes and in the leaching-test eluates were analysed. It seemed likely that leached formaldehyde caused very high acute toxicity in leaching-test eluates of the dry-booth residues. This hypothesis was based on the fact that the formaldehyde concentrations in the leaching-test eluates of the dry-booth residues were 62-75 times higher than the EC50 value reported in the literature for formaldehyde. The results of the water-curtain booth residues showed that the samples with the highest TOC and aromatic solvent concentrations were also the most toxic. The studied excess paint residues were complex organic mixtures and contained large amounts of compounds not identifiable from chemical data. Therefore, the evaluation of the hazard based solely on available chemical data is unlikely to be sufficient, as evidenced by our study. Our results show that harmful compounds remain in the solid waste and the toxicity results of their leaching-test eluates show that toxicity may leach from residues in contact with water at landfill sites. They also confirm the benefit of combining chemical and ecotoxicological assays in assessing the potential environmental hazard of complex organic mixtures found in wastes. Copyright 2003 Elsevier B.V.

Color deviation controlling of phosphor conformal coating by advanced spray painting technology for white LEDs.

PubMed

Yang, Liang; Wang, Simin; Lv, Zhicheng; Liu, Sheng

2013-04-01

An advanced phosphor conformal coating technology is proposed, good correlated color temperature (CCT) and chromaticity uniformity samples are fabricated through phosphor spray painting technology. Spray painting technology is also suitable for phosphor conformal coating of whole LED wafers. The samples of different CCTs are obtained through controlling the phosphor film thickness in the range of 6-80 μm; CCT variation of samples can be controlled in the range of ±200 K. The experimental Δuv reveals that the spray painting method can obtain a much smaller CCT variation (Δuv of 1.36e(-3)) than the conventional dispensing method (Δuv of 11.86e(-3)) when the light is emitted at angles from -90° to +90°, and chromaticity area uniformity is also improved significantly.

Paint-Overspray Catcher

NASA Technical Reports Server (NTRS)

Weinstein, Leonard M.

2003-01-01

An apparatus to catch paint overspray has been proposed. Overspray is an unavoidable parasitic component of spray that occurs because the flow of air or other gas in the spray must turn at the sprayed surface. Very small droplets are carried away in this turning flow, and some land on adjacent surfaces not meant to be painted. The basic principle of the paint-spray catcher is to divert the overspray into a suction system at the boundary of the area to be painted. The paint-spray catcher (see figure) would include a toroidal plenum connected through narrow throat to a nozzle that would face toward the center of the torus, which would be positioned over the center of the area to be spray-painted. The plenum would be supported by four tubes that would also serve as suction exhaust ducts. The downstream ends of the tubes (not shown in the figure) would be connected to a filter on a suction pump. The pump would be rated to provide a suction mass flow somewhat greater than that of the directed spray gas stream, so that the nozzle would take in a small excess of surrounding gas and catch nearly all of the overspray. A small raised lip at the bottom edge of the nozzle would catch paint that landed inside the nozzle. Even if the paint is directly piston pumped, the droplets entrain an air flow by time they approach the wall, so there is always a gas stream to carry the excess droplets to the side. For long-duration spraying operations, it could be desirable to include a suction-drain apparatus to prevent overflowing and dripping of paint from inside the lip. A version without an external contraction and with the throat angled downward would be a more compact version of catcher, although it might be slightly less efficient.

40 CFR 63.11171 - How do I know if my source is considered a new source or an existing source?

Code of Federal Regulations, 2010 CFR

2010-07-01

... associated equipment; (3) Spray guns and associated equipment; (4) Spray gun cleaning equipment; (5... stripping or surface coating equipment. If you purchase and install spray booths, enclosed spray gun cleaners, paint stripping equipment to reduce MeCl emissions, or purchase new spray guns to comply with...

IPMC paints

NASA Astrophysics Data System (ADS)

Park, Il-Seok; Tiwari, Rashi; Kim, Kwang J.

2008-03-01

In this paper we are reporting a newely developed IPMC fabrication method, "IPMC Paint", which can be directly sprayed onto any complex surface. In order to fabricate the IPMC paint, liquid Nafion TM was used for the ionic conducting polymer instead of the typical film/sheet type Nafion TM. The viscosity of liquid Nafion TM was adjusted by adding Polyvinylpyrrolidone (PVP) to perform spray painting. Modified Nafion was sprayed onto the conducting substrate, Polyfoil TM which acts as base electrode layer. After three times spraying, ionic polymer layer has 45 μm thickness and 10 μm of surface roughness. Sensing tests show that IPMC paint sensor has more sensitivity (+/- 0.06 of producing voltage) than that of the typical IPMC (+/- 0.005 of producing voltage) when dynamic bending with 10 Hz frequency and 1.3 cm of displacement is applied to.

Auditory Processing Testing: In the Booth versus Outside the Booth.

PubMed

Lucker, Jay R

2017-09-01

Many audiologists believe that auditory processing testing must be carried out in a soundproof booth. This expectation is especially a problem in places such as elementary schools. Research comparing pure-tone thresholds obtained in sound booths compared to quiet test environments outside of these booths does not support that belief. Auditory processing testing is generally carried out at above threshold levels, and therefore may be even less likely to require a soundproof booth. The present study was carried out to compare test results in soundproof booths versus quiet rooms. The purpose of this study was to determine whether auditory processing tests can be administered in a quiet test room rather than in the soundproof test suite. The outcomes would identify that audiologists can provide auditory processing testing for children under various test conditions including quiet rooms at their school. A battery of auditory processing tests was administered at a test level equivalent to 50 dB HL through headphones. The same equipment was used for testing in both locations. Twenty participants identified with normal hearing were included in this study, ten having no auditory processing concerns and ten exhibiting auditory processing problems. All participants underwent a battery of tests, both inside the test booth and outside the booth in a quiet room. Order of testing (inside versus outside) was counterbalanced. Participants were first determined to have normal hearing thresholds for tones and speech. Auditory processing tests were recorded and presented from an HP EliteBook laptop computer with noise-canceling headphones attached to a y-cord that not only presented the test stimuli to the participants but also allowed monitor headphones to be worn by the evaluator. The same equipment was used inside as well as outside the booth. No differences were found for each auditory processing measure as a function of the test setting or the order in which testing was done

Visual comparison testing of automotive paint simulation

NASA Astrophysics Data System (ADS)

Meyer, Gary; Fan, Hua-Tzu; Seubert, Christopher; Evey, Curtis; Meseth, Jan; Schnackenberg, Ryan

2015-03-01

An experiment was performed to determine whether typical industrial automotive color paint comparisons made using real physical samples could also be carried out using a digital simulation displayed on a calibrated color television monitor. A special light booth, designed to facilitate evaluation of the car paint color with reflectance angle, was employed in both the real and virtual color comparisons. Paint samples were measured using a multi-angle spectrophotometer and were simulated using a commercially available software package. Subjects performed the test quicker using the computer graphic simulation, and results indicate that there is only a small difference between the decisions made using the light booth and the computer monitor. This outcome demonstrates the potential of employing simulations to replace some of the time consuming work with real physical samples that still characterizes material appearance work in industry.

Spray-painted binder-free SnSe electrodes for high-performance energy-storage devices.

PubMed

Wang, Xianfu; Liu, Bin; Xiang, Qingyi; Wang, Qiufan; Hou, Xiaojuan; Chen, Di; Shen, Guozhen

2014-01-01

SnSe nanocrystal electrodes on three-dimensional (3D) carbon fabric and Au-coated polyethylene terephthalate (PET) wafer have been prepared by a simple spray-painting process and were further investigated as binder-free active-electrodes for Lithium-ion batteries (LIBs) and flexible stacked all-solid-state supercapacitors. The as-painted SnSe nanocrystals/carbon fabric electrodes exhibit an outstanding capacity of 676 mAh g(-1) after 80 cycles at a current density of 200 mA g(-1) and a considerable high-rate capability in lithium storage because of the excellent ion transport from the electrolyte to the active materials and the efficient charge transport between current collector and electrode materials. The binder-free electrodes also provide a larger electrochemical active surface compared with electrodes containing binders, which leads to the enhanced capacities of energy-storage devices. A flexible stacked all-solid-state supercapacitor based on the SnSe nanocrystals on Au-coated PET wafers shows high capacitance reversibility with little performance degradation at different current densities after 2200 charge-discharge cycles and even when bent. This allows for many potential applications in facile, cost-effective, spray-paintable, and flexible energy-storage devices. The results indicate that the fabrication of binder-free electrodes by a spray painting process is an interesting direction for the preparation of high-performance energy-storage devices. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Exposure to Airborne Particles and Volatile Organic Compounds from Polyurethane Molding, Spray Painting, Lacquering, and Gluing in a Workshop

PubMed Central

Mølgaard, Bjarke; Viitanen, Anna-Kaisa; Kangas, Anneli; Huhtiniemi, Marika; Larsen, Søren Thor; Vanhala, Esa; Hussein, Tareq; Boor, Brandon E.; Hämeri, Kaarle; Koivisto, Antti Joonas

2015-01-01

Due to the health risk related to occupational air pollution exposure, we assessed concentrations and identified sources of particles and volatile organic compounds (VOCs) in a handcraft workshop producing fishing lures. The work processes in the site included polyurethane molding, spray painting, lacquering, and gluing. We measured total VOC (TVOC) concentrations and particle size distributions at three locations representing the various phases of the manufacturing and assembly process. The mean working-hour TVOC concentrations in three locations studied were 41, 37, and 24 ppm according to photo-ionization detector measurements. The mean working-hour particle number concentration varied between locations from 3000 to 36,000 cm−3. Analysis of temporal and spatial variations of TVOC concentrations revealed that there were at least four substantial VOC sources: spray gluing, mold-release agent spraying, continuous evaporation from various lacquer and paint containers, and either spray painting or lacquering (probably both). The mold-release agent spray was indirectly also a major source of ultrafine particles. The workers’ exposure can be reduced by improving the local exhaust ventilation at the known sources and by increasing the ventilation rate in the area with the continuous source. PMID:25849539

Demonstration of Split-Flow Ventilation and Recirculation as Flow- Reduction Methods in an Air Force Paint Spray Booth. Volume 1

DTIC Science & Technology

1994-07-27

of the split-flow and recirculation modifications in typical Air Force painting operations; itwas a proof-of- concept study only. It is recognized...recirculating ventilation. 4 To Implement this flow-reduction concept , it must first be established that recirculation does not cause an accumulation of toxic...ventilation concept . The concentration gradient is determined by height and direction of paint application. If the concentration in the top portion is

Workplace protection of air-fed visors used in paint spraying operations.

PubMed

Bolsover, J; Rajan-Sithamparanadarajah, B; Vaughan, N

2006-04-01

Air-fed visors are commonly used for protection against exposure to airborne isocyanates during paint spraying. Protection levels for this class of equipment are theoretically adequate, yet isocyanate sensitization in this occupation still occurs. The work reported here set out to establish the level of respiratory protection that is achieved during real paint spraying activities when air-fed visors are used. The work also examined the effects of reduced air supply flow rates on this type of respiratory protection. The workplace study highlighted common problems that occur when attempting to measure protection factors, and process and interpret the collected data. Many of the environments included in this study did not exhibit challenge concentrations high enough to reliably measure the workplace protection factor of this class of device. When detection limits are taken into consideration, the remaining field data suggest that an assigned protection factor in the region of 40 may be appropriate. When well maintained and used in accordance with the manufacturer's instructions, air-fed visors are capable of providing a good level of respiratory protection. The protection given by air-fed visors is strongly dependent on the air flow supplied to them. Laboratory measurements demonstrate that protection falls as the air supply falls. This is a gradual process and does not suddenly occur at any particular air supply flow. Observations made during the field tests indicate that there may be other activities associated with the spraying process that need to be taken into consideration when looking for sources of respiratory sensitization.

Toll-Booth Purification

NASA Technical Reports Server (NTRS)

1977-01-01

NASA's Technology Application Team at Stanford Research Institute searched available information and suggested a transfer of clean-room technology employing the use of the same laminar flow techniques found in environmental control systems of clean rooms used for contamination-free assembly of precision aerospace equipment. That information, from technology originally developed by NASA and the Energy Research & Development Administration was incorporated in the design of a prototype toll booth purifier. The draft-free design includes a "diffusor", which blows clean air out the toll booth doorway, thus retarding the infiltration of contaminated air. The net effect is a decrease in the toll collector's inhalation of exhaust fumes. The Washington Department of Highways installed the prototype system in a toll booth at the Evergreen Point Bridge near Seattle. After a successful two-year test, the department now has equipped all 10 of the bridge's toll booths with the air purifiers.

Implementation of a solvent management program to control paint shop volatile organic compounds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Floer, M.M.; Hicks, B.H.

1997-12-31

The majority of automobile assembly plant volatile organic compound (VOC) emissions are generated from painting operations. Typical paint operations generate more than 90 percent of the total plant emissions and, up to, 50 percent can be released by cleaning sources. Plant practices which contribute to the release of VOC emissions include the cleaning of paint lines and equipment, tanks, spray booths, floors and vehicles. Solvents continue to be the largest contributing source of VOC emissions in an automotive paint shop. To reduce overall VOC emissions, environmental regulations and guidelines were introduced under the Clean Air Act; Pollution Prevention and Wastemore » Minimization programs, Control Techniques, and special air permit conditions. The introduction of these regulations and guidelines has driven industry toward continual refinement of their present cleaning methods while pursuing new techniques and technologies. Industry has also shown a proactive approach by introducing new waterborne and powder coating paint technologies to reduce overall emissions. As new paint technologies are developed and introduced, special attention must be given to the types of materials utilized for cleaning. The development and implementation of a solvent management program allows a facility to standardize a program to properly implement materials, equipment, technologies and work practices to reduce volatile organic compound emissions, meet strict cleaning requirements posed by new paint technologies and produce a vehicle which meets the high quality standards of the customer. This paper will assess the effectiveness of a solvent management program by examining pollution prevention initiatives and data from four different painting operations.« less

Isocyanate exposures in autobody shop work: the SPRAY study.

PubMed

Sparer, Judy; Stowe, Meredith H; Bello, Dhimiter; Liu, Youcheng; Gore, Rebecca J; Youngs, Fred; Cullen, Mark R; Redlich, Carrie A; Woskie, Susan R

2004-09-01

Isocyanates, known to cause respiratory sensitization and asthma, are widely used in automotive refinishing where exposures to aliphatic polyisocyanates occur by both inhalation and skin contact. The work reported here, the characterization of isocyanate exposure in the autobody industry, was part of an epidemiologic study of workers in 37 autobody shops in Connecticut. This article describes workplaces, tasks, and controls, and outlines the frequency, duration, and intensity of isocyanate exposures. Personal air samples taken outside of respirators had median concentrations of 66.5 microg NCO/m3 for primer, 134.4 microg (NCO)/m3 for sealer, and 358.5 microg NCO/m3 for clearcoat. Forty-eight percent of primer, 66% of sealer, and 92% of clearcoat samples exceeded the United Kingdom Health and Safety Executive guideline for isocyanate, though none exceeded the National Institute for Occupational Safety and Health (NIOSH) recommended exposure limit for monomer. Nonisocyanate-containing primers and sealers are used in more than half the shops, but nonisocyanate clearcoats are rare. Eighty-two percent of personal samples taken within a spray booth exceeded the U.K. guideline: 81% of those in downdraft spray booths, 74% in semidowndraft booths, and 92% in crossdraft booths. Only 8% of shops reported that spraying is done exclusively in spray booths. All painters wore some type of respirator. In 30% of shops, painters used supplied air respirators; the rest relied on half face organic vapor cartridge respirators with N95 overspray pads. All shops provided some type of gloves, usually latex, not recommended for isocyanate protection. Despite improvements in autobody shop materials, practices, and controls, there are still opportunities for substantial exposures to isocyanates.

Surface modeling of workpiece and tool trajectory planning for spray painting robot.

PubMed

Tang, Yang; Chen, Wei

2015-01-01

Automated tool trajectory planning for spray-painting robots is still a challenging problem, especially for a large free-form surface. A grid approximation of a free-form surface is adopted in CAD modeling in this paper. A free-form surface model is approximated by a set of flat patches. We describe here an efficient and flexible tool trajectory optimization scheme using T-Bézier curves calculated in a new way from trigonometrical bases. The distance between the spray gun and the free-form surface along the normal vector is varied. Automotive body parts, which are large free-form surfaces, are used to test the scheme. The experimental results show that the trajectory planning algorithm achieves satisfactory performance. This algorithm can also be extended to other applications.

Space Paint

NASA Technical Reports Server (NTRS)

1976-01-01

Developed at Goddard, this improved inorganic paint may help protect coastal bridges subject to extreme corrosion from seawater spray. Potassium silicate formulated into a thin waterbase binder that sprays easily, adheres readily, and can be heavily loaded with zinc particles to provide uniform coverage in a single coat. Stanford Research Institute has measured an annual market in excess of $2 billion in painting highway bridges, utility pipelines, nuclear reactors, and railcar hoppers. Other suitable markets include offshore drilling facilities, railroad bridges, and ships.

Surface Modeling of Workpiece and Tool Trajectory Planning for Spray Painting Robot

PubMed Central

Tang, Yang; Chen, Wei

2015-01-01

Automated tool trajectory planning for spray-painting robots is still a challenging problem, especially for a large free-form surface. A grid approximation of a free-form surface is adopted in CAD modeling in this paper. A free-form surface model is approximated by a set of flat patches. We describe here an efficient and flexible tool trajectory optimization scheme using T-Bézier curves calculated in a new way from trigonometrical bases. The distance between the spray gun and the free-form surface along the normal vector is varied. Automotive body parts, which are large free-form surfaces, are used to test the scheme. The experimental results show that the trajectory planning algorithm achieves satisfactory performance. This algorithm can also be extended to other applications. PMID:25993663

COMPARATIVE STUDY OF SPRAY BOOTH FILTER SYSTEM EFFICIENCY

EPA Science Inventory

The paper summarizes results of research conducted to determine the capability of various dry paint overspray arrestor systems to capture particles as small as about 1 micrometer in surface diameter. The testing used on optical particle counter to determine the concentration of p...

Effects of Known Determinants on Methylene Bisphenyl Isocyanate (MDI) Concentration During Spray-On Truck Bed-Lining Processes.

PubMed

Schaal, Nicholas C; Brazile, William J; Finnie, Katie L; Tiger, James P

2017-08-01

Occupational exposure to methylene bisphenyl isocyanate (MDI) presents serious worker health concerns as it may lead to short- and long-term health effects such as asthma, airway irritation, hypersensitivity pneumonitis, and irritation of skin and mucous membranes. While studies of worker isocyanate exposures during vehicle painting activities are widespread, few studies have investigated the spray-on truck bed-liner (STBL) industry. The purpose of this study was to determine the effectiveness of several ventilation system variables and process characteristics in controlling MDI concentrations in the STBL industry. A total of 47 personal air samples were collected for MDI during 18 site visits at nine STBL companies in Colorado and Wyoming. Ventilation system and process characteristics that were assessed included: ventilation system face velocity, airflow, air changes per minute (AC/M), capture velocity, percent of MDI in bed-liner product, application temperature, application pressure, paint booth temperature, paint booth relative humidity, paint booth volume, and quantity of bed-liner product applied. Pearson correlation revealed percentage of MDI in bed-liner product (r = 0.557, n = 14, P < 0.05) and process temperature (r = 0.677, n = 14, P < 0.05) had high positive correlation with MDI concentration. Ventilation system face velocity (r = -0.578, n = 14, P < 0.05) and AC/M (r = -0.657, n = 14, P < 0.05) had high negative correlation with MDI concentration while airflow (r = -0.475, n = 14, P < 0.05) and capture velocity (r = -0.415, n = 14, P = 0.07) had moderate negative correlation with MDI concentration. Multiple linear regression revealed process temperature and capture velocity made a statistically significant and unique contribution in estimating MDI concentration (F (2, 11) = 10.99, P < 0.05) with an adjusted R2 of 0.61, explaining 61% of the variability in MDI concentration. This investigation contributed to an understudied STBL industry by targeting

29 CFR 1917.153 - Spray painting (See also § 1917.2, definition of Hazardous cargo, materials, substance, or...

Code of Federal Regulations, 2011 CFR

2011-07-01

... partition. (ii) Hot surfaces shall not be located in spraying areas. (iii) Whenever combustible residues may... cleaning, paper may be used to cover the floor during painting operations if it is removed after the...

29 CFR 1917.153 - Spray painting (See also § 1917.2, definition of Hazardous cargo, materials, substance, or...

Code of Federal Regulations, 2013 CFR

2013-07-01

... partition. (ii) Hot surfaces shall not be located in spraying areas. (iii) Whenever combustible residues may... cleaning, paper may be used to cover the floor during painting operations if it is removed after the...

29 CFR 1917.153 - Spray painting (See also § 1917.2, definition of Hazardous cargo, materials, substance, or...

Code of Federal Regulations, 2012 CFR

2012-07-01

... partition. (ii) Hot surfaces shall not be located in spraying areas. (iii) Whenever combustible residues may... cleaning, paper may be used to cover the floor during painting operations if it is removed after the...

29 CFR 1917.153 - Spray painting (See also § 1917.2, definition of Hazardous cargo, materials, substance, or...

Code of Federal Regulations, 2014 CFR

2014-07-01

... partition. (ii) Hot surfaces shall not be located in spraying areas. (iii) Whenever combustible residues may... cleaning, paper may be used to cover the floor during painting operations if it is removed after the...

Paints and Preservatives.

ERIC Educational Resources Information Center

Powell, Larry E.; Miller, Larry E.

The publication contains an outline for use by agriculture teachers in developing a teaching plan for a unit on paints and preservatives. The topics included are (1) recognizing, solving, and preventing paint problems and (2) operating and using power spray painting equipment. Items presented for each topic are: the situation, (intended to inform…

Spray-on tanning.

PubMed

Rogers, Cindy J

2005-01-01

The modern formulation of dihydroxyacetone (DHA), the only sunless tanning solution approved by the Food and Drug Administration (FDA), is combined with bronzers and moisturizers to deliver a cosmetically acceptable skin color and a natural-looking tan without ultraviolet (UV) exposure. Spray-on tanning products, which deliver this formulation evenly to achieve a full body tan, may be applied in a tanning booth, airbrushed on by a technician, or sprayed on at home, and they appear to offer a generally safe alternative for patients who seek a suntanned appearance.

Thermal spray for commercial shipbuilding

NASA Astrophysics Data System (ADS)

Rogers, F. S.

1997-09-01

Thermal spraying of steel with aluminum to protect it from corrosion is a technology that has been proven to work in the marine environment. The thermal spray coating system includes a paint sealer that is applied over the thermally sprayed aluminum. This extends the service life of the coating and provides color to the end product. The thermal spray system protects steel both through the principle of isolation (as in painting) and galvanizing. With this dual protection mechanism, steel is protected from corrosion even when the coating is damaged. The thermal- sprayed aluminum coating system has proved the most cost- effective corrosion protection system for the marine environment. Until recently, however, the initial cost of application has limited its use for general application. Arc spray technology has reduced the application cost of thermal spraying of aluminum to below that of painting. Commercial shipbuilders could use this technology to enhance their market position in the marine industry.

Toluene inducing acute respiratory failure in a spray paint sniffer.

PubMed

Peralta, Diego P; Chang, Aymara Y

2012-01-01

Toluene, formerly known as toluol, is an aromatic hydrocarbon that is widely used as an industrial feedstock and as a solvent. Like other solvents, toluene is sometimes also used as an inhalant drug for its intoxicating properties. It has potential to cause multiple effects in the body including death. I report a case of a 27-year-old male, chronic spray paint sniffer, who presented with severe generalized muscle weakness and developed acute respiratory failure requiring ventilatory support. Toluene toxicity was confirmed with measurement of hippuric acid of 8.0 g/L (normal <5.0 g/L). Acute respiratory failure is a rare complication of chronic toluene exposure that may be lethal if it is not recognized immediately. To our knowledge, this is the second case of acute respiratory failure due to toluene exposure.

Fallout from the Shuttle Arm

NASA Technical Reports Server (NTRS)

1990-01-01

Vadeko International, Inc., Mississauga, Ontario developed for the Canadian National Railways (CN) the Robotic Paint Application System. The robotic paint shop has two parallel paint booths, allowing simultaneous painting of two hopper cars. Each booth has three robots, two that move along wall-mounted rails to spray-paint the exterior, a third that is lowered through a hatch in the railcar's top to paint the interior. A fully computerized system controls the movement of the robots and the painting process. The robots can do in four hours a job that formerly took 32 hours. The robotic system applies a more thorough coating and CN expects that will double the useful life of its hoppers and improve cost efficiency. Human painters no longer have to handle the difficult and hazardous job. CN paint shop employees have been retrained to operate the computer system that controls the robots. In addition to large scale robotic systems, Vadeko International is engaged in such other areas of technology as flexible automation, nuclear maintenance, underwater vehicles, thin film deposition and wide band monitoring.

40 CFR 429.160 - Applicability; description of the wood furniture and fixture production without water wash spray...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS (CONTINUED) TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and... Applicability; description of the wood furniture and fixture production without water wash spray booth(s) or...

40 CFR 429.170 - Applicability; description of the wood furniture and fixture production with water wash spray...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS (CONTINUED) TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and... Applicability; description of the wood furniture and fixture production with water wash spray booth(s) or with...

40 CFR 429.170 - Applicability; description of the wood furniture and fixture production with water wash spray...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS (CONTINUED) TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and... Applicability; description of the wood furniture and fixture production with water wash spray booth(s) or with...

40 CFR 429.170 - Applicability; description of the wood furniture and fixture production with water wash spray...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS (CONTINUED) TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and... Applicability; description of the wood furniture and fixture production with water wash spray booth(s) or with...

40 CFR 429.160 - Applicability; description of the wood furniture and fixture production without water wash spray...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS (CONTINUED) TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and... Applicability; description of the wood furniture and fixture production without water wash spray booth(s) or...

40 CFR 429.160 - Applicability; description of the wood furniture and fixture production without water wash spray...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS (CONTINUED) TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and... Applicability; description of the wood furniture and fixture production without water wash spray booth(s) or...

40 CFR 429.160 - Applicability; description of the wood furniture and fixture production without water wash spray...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and Fixture... Applicability; description of the wood furniture and fixture production without water wash spray booth(s) or...

40 CFR 429.170 - Applicability; description of the wood furniture and fixture production with water wash spray...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and Fixture...; description of the wood furniture and fixture production with water wash spray booth(s) or with laundry...

40 CFR 429.170 - Applicability; description of the wood furniture and fixture production with water wash spray...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and Fixture...; description of the wood furniture and fixture production with water wash spray booth(s) or with laundry...

40 CFR 429.160 - Applicability; description of the wood furniture and fixture production without water wash spray...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the wood... GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Wood Furniture and Fixture... Applicability; description of the wood furniture and fixture production without water wash spray booth(s) or...

Toluene inducing acute respiratory failure in a spray paint sniffer

PubMed Central

Peralta, Diego P.; Chang, Aymara Y.

2012-01-01

Summary Background: Toluene, formerly known as toluol, is an aromatic hydrocarbon that is widely used as an industrial feedstock and as a solvent. Like other solvents, toluene is sometimes also used as an inhalant drug for its intoxicating properties. It has potential to cause multiple effects in the body including death. Case Report: I report a case of a 27-year-old male, chronic spray paint sniffer, who presented with severe generalized muscle weakness and developed acute respiratory failure requiring ventilatory support. Toluene toxicity was confirmed with measurement of hippuric acid of 8.0 g/L (normal <5.0 g/L). Conclusions: Acute respiratory failure is a rare complication of chronic toluene exposure that may be lethal if it is not recognized immediately. To our knowledge, this is the second case of acute respiratory failure due to toluene exposure. PMID:23569498

Performance of a pilot-scale biotrickling filter in controlling the volatile organic compound emissions in a furniture manufacturing facility.

PubMed

Martínez-Soria, Vicente; Gabaldón, Carmen; Penya-Roja, Josep M; Palau, Jordi; Alvarez-Hornos, F Javier; Sempere, Feliu; Soriano, Carlos

2009-08-01

A 0.75-m3 pilot-scale biotrickling filter was run for over 1 yr in a Spanish furniture company to evaluate its performance in the removal of volatile organic compounds (VOCs) contained in the emission of two different paint spray booths. The first one was an open front booth used to manually paint furniture, and the second focus was an automatically operated closed booth operated to paint pieces of furniture. In both cases, the VOC emissions were very irregular, with rapid and extreme fluctuations. The pilot plant was operated at an empty bed residence time (EBRT) ranging from 10 to 40 sec, and good removal efficiencies of VOCs were usually obtained. When a buffering activated carbon prefilter was installed, the system performance was improved considerably, so a much better compliance with legal constraints was reached. After different shutdowns in the factory, the period to recover the previous performance of the biotrickling reactor was minimal. A weekend dehydration strategy was developed and implemented to control the pressure drop associated with excessive biomass accumulation.

SPATTER! SPATTER! SPATTER! Workers' health and the spray machine debate.

PubMed

Frounfelker, Rochelle L

2006-02-01

A conflict between industrialization and worker health developed in the painting industry during the early 1900s with the introduction of the spray machine. This technological innovation allowed the application of paint at greater speed and lower cost than hand painting and increased the rate at which painters were exposed to lead and other toxins contained in paint. From roughly 1919 to 1931, the painters' trade union clashed with employers, paint manufacturers, and legislatures over the impact of the spray machine on the health of workers and the need to enact legislation to regulate its use. While painters made gains on local, state, and national levels during the 1920s to prevent the use of the spray machine, their efforts ultimately failed.

Stabilization/solidification of an alkyd paint waste by carbonation of waste-lime based formulations.

PubMed

Arce, R; Galán, B; Coz, A; Andrés, A; Viguri, J R

2010-05-15

The application of solvent-based paints by spraying in paint booths is extensively used in a wide range of industrial activities for the surface treatment of a vast array of products. The wastes generated as overspray represent an important environmental and managerial problem mainly due to the hazardous characteristics of the organic solvent, rendering it necessary to appropriately manage this waste. In this paper a solidification/stabilization (S/S) process based on accelerated carbonation was investigated as an immobilization pre-treatment prior to the disposal, via landfill, of an alkyd solvent-based paint waste coming from the automotive industry; the purpose of this S/S process was to immobilize the contaminants and reduce their release into the environment. Different formulations of paint waste with lime, lime-coal fly-ash and lime-Portland cement were carbonated to study the effect of the water/solid ratio and carbonation time on the characteristics of the final product. To assess the efficiency of the studied S/S process, metals, anions and dissolved organic carbon (DOC) were analyzed in the leachates obtained from a battery of compliance and characterization leaching tests. Regarding the carbonation of paint waste-lime formulations, a mathematical expression has been proposed to predict the results of the leachability of DOC from carbonated mixtures working at water/solid ratios from 0.2 to 0.6. However, lower DOC concentrations in leachates (400mg/kg DOC in L/S=10 batch leaching test) were obtained when carbonation of paint waste-lime-fly-ash mixtures was used at 10h carbonation and water to solid ratio of 0.2. The flammability characteristics, the total contents of contaminants and the contaminant release rate in compliance leaching tests provide evidence for a final product suitable for deposition in non-hazardous landfills. The characterization of this carbonated sample using a dynamic column leaching test shows a high stabilization of metals, partial

40 CFR Table 1 to Subpart Hhhhhh... - Applicability of General Provisions to Subpart HHHHHH of Part 63

Code of Federal Regulations, 2012 CFR

2012-07-01

.../Reporting Waiver Yes § 63.11 Control Device Requirements/Flares No Subpart HHHHHH does not require the use... Control Agencies and EPA Regional Offices Yes § 63.14 Incorporation by Reference Yes Test methods for measuring paint booth filter efficiency and spray gun transfer efficiency in § 63.11173(e)(2) and (3) are...

40 CFR Table 1 to Subpart Hhhhhh... - Applicability of General Provisions to Subpart HHHHHH of Part 63

Code of Federal Regulations, 2011 CFR

2011-07-01

.../Reporting Waiver Yes § 63.11 Control Device Requirements/Flares No Subpart HHHHHH does not require the use... Control Agencies and EPA Regional Offices Yes § 63.14 Incorporation by Reference Yes Test methods for measuring paint booth filter efficiency and spray gun transfer efficiency in § 63.11173(e)(2) and (3) are...

40 CFR Table 1 to Subpart Hhhhhh... - Applicability of General Provisions to Subpart HHHHHH of Part 63

Code of Federal Regulations, 2014 CFR

2014-07-01

.../Reporting Waiver Yes § 63.11 Control Device Requirements/Flares No Subpart HHHHHH does not require the use... Control Agencies and EPA Regional Offices Yes § 63.14 Incorporation by Reference Yes Test methods for measuring paint booth filter efficiency and spray gun transfer efficiency in § 63.11173(e)(2) and (3) are...

40 CFR Table 1 to Subpart Hhhhhh... - Applicability of General Provisions to Subpart HHHHHH of Part 63

Code of Federal Regulations, 2013 CFR

2013-07-01

.../Reporting Waiver Yes § 63.11 Control Device Requirements/Flares No Subpart HHHHHH does not require the use... Control Agencies and EPA Regional Offices Yes § 63.14 Incorporation by Reference Yes Test methods for measuring paint booth filter efficiency and spray gun transfer efficiency in § 63.11173(e)(2) and (3) are...

Air cleaning performance of a new environmentally controlled primary crusher operator booth.

PubMed

Organiscak, J A; Cecala, A B; Zimmer, J A; Holen, B; Baregi, J R

2016-02-01

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company's Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system's effectiveness in controlling airborne dusts and particulates. The booth's dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-μm respirable size particulates under various HVAC airflow operating conditions.

40 CFR Table 1 to Subpart Hhhhhh... - Applicability of General Provisions to Subpart HHHHHH of Part 63

Code of Federal Regulations, 2010 CFR

2010-07-01

... measuring paint booth filter efficiency and spray gun transfer efficiency in § 63.11173(e)(2) and (3) are... the obligation to obtain Title V operating permits. § 63.1(c)(5) Notifications Yes § 63.1(e...) Compliance Dates for Existing Sources Yes § 63.11172 specifies the compliance dates. § 63.6(e)(1)-(2...

Improved Orifice Plate for Spray Gun

NASA Technical Reports Server (NTRS)

Cunningham, W.

1986-01-01

Erratic spray pattern of commercial spray gun changed to repeatable one by simple redesign of two parts. In modified spray gun orifice plate and polytetrafluoroethylene bushing redesigned to assure centering and alignment with nozzle. Such improvement useful in many industrial applications requiring repeatable spray patterns. Might include spraying of foam insulation, paint, other protective coatings, detergents, abrasives, adhesives, process chemicals, or fuels. Unmodified spray gun produces erratic spray because lateral misalignment between orifice plate and nozzle.

Development of 6-DOF painting robot control system

NASA Astrophysics Data System (ADS)

Huang, Junbiao; Liu, Jianqun; Gao, Weiqiang

2017-01-01

With the development of society, the spraying technology of manufacturing industry in China has changed from the manual operation to the 6-DOF (Degree Of Freedom)robot automatic spraying. Spraying painting robot can not only complete the work which does harm to human being, but also improve the production efficiency and save labor costs. Control system is the most critical part of the 6-DOF robots, however, there is still a lack of relevant technology research in China. It is very necessary to study a kind of control system of 6-DOF spraying painting robots which is easy to operation, and has high efficiency and stable performance. With Googol controller platform, this paper develops programs based on Windows CE embedded systems to control the robot to finish the painting work. Software development is the core of the robot control system, including the direct teaching module, playback module, motion control module, setting module, man-machine interface, alarm module, log module, etc. All the development work of the entire software system has been completed, and it has been verified that the entire software works steady and efficient.

Air cleaning performance of a new environmentally controlled primary crusher operator booth

PubMed Central

Organiscak, J.A.; Cecala, A.B.; Zimmer, J.A.; Holen, B.; Baregi, J.R.

2016-01-01

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-μm respirable size particulates under various HVAC airflow operating conditions. PMID:26937052

Postscript: Plaut and Booth's (2006) New Simulations--What Have We Learned?

ERIC Educational Resources Information Center

Besner, Derek; Borowsky, Ron

2006-01-01

This paper comments on the article by Plaut and Booth. Plaut and Booth's first simulation shows that there is essentially perfect discrimination between word and nonwords sharing the same orthographic structure when the simulation is carried out in the way we suggested. We take the view that Plaut and Booth's new simulation work settles little…

Spray-painted human fibronectin coating as an effective strategy to enhance graft ligamentization of a polyethylene terephthalate artificial ligament.

PubMed

Li, Hong; Chen, Chen; Ge, Yunsheng; Chen, Shiyi

2014-05-01

To enhance graft ligamentization after anterior cruciate ligament (ACL) reconstruction, human fibronectin (FN) was coated on polyethylene terephthalate (PET) ligaments by spray painting. The FN-coated PET ligaments were investigated in vitro using rat mesenchymal stromal cells (MSCs). MSCs cultured on FN-coated grafts resulted in similar cell densities and amounts of proliferating cells with control grafts without coating. The FN-coated group not only gave rise to MSC-derived collagen-like tissues but also enhanced the expression of collagen-I gene. Furthermore, rat ACL reconstruction models were used to evaluate the effect of the FN coating in vivo. The FN coating significantly promoted new ligament tissue regeneration into the graft fibers. In conclusion, sprayed FN coating had a positive effect to enhance graft ligamentization of PET artificial ligament.

Performance evaluation of mobile downflow booths for reducing airborne particles in the workplace.

PubMed

Lo, Li-Ming; Hocker, Braden; Steltz, Austin E; Kremer, John; Feng, H Amy

2017-11-01

Compared to other common control measures, the downflow booth is a costly engineering control used to contain airborne dust or particles. The downflow booth provides unidirectional filtered airflow from the ceiling, entraining released particles away from the workers' breathing zone, and delivers contained airflow to a lower level exhaust for removing particulates by filtering media. In this study, we designed and built a mobile downflow booth that is capable of quick assembly and easy size change to provide greater flexibility and particle control for various manufacturing processes or tasks. An experimental study was conducted to thoroughly evaluate the control performance of downflow booths used for removing airborne particles generated by the transfer of powdered lactose between two containers. Statistical analysis compared particle reduction ratios obtained from various test conditions including booth size (short, regular, or extended), supply air velocity (0.41 and 0.51 m/s or 80 and 100 feet per minute, fpm), powder transfer location (near or far from the booth exhaust), and inclusion or exclusion of curtains at the booth entrance. Our study results show that only short-depth downflow booths failed to protect the worker performing powder transfer far from the booth exhausts. Statistical analysis shows that better control performance can be obtained with supply air velocity of 0.51 m/s (100 fpm) than with 0.41 m/s (80 fpm) and that use of curtains for downflow booths did not improve their control performance.

Personnel Exposure to Airborne Isocyanates and Solvents During Shipboard Painting With 2-Pack Polyurethane Paints

DTIC Science & Technology

2008-12-01

contain low volatility isocyanate prepolymers in addition to small quantities of volatile isocyanate monomers [2,3]. The monomers may become airborne as...vapour whilst the non-volatile prepolymers and partially cured oligomers may form aerosols during spray painting and sanding of the painted surface...JL (1992) “ Prepolymers of hexamethylene diisocyanate as a cause of occupational asthma” J. Allergy Clinical Immunol. 91 850-61. 5. Redlich CA, Bello

Glass composition development for stabilization of lead based paints

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marra, J.C.

1996-10-01

Exposure to lead can lead to adverse health affects including permanent damage to the central nervous system. Common means of exposure to lead are from ingestion of lead paint chips or breathing of dust from deteriorating painted surfaces. The U.S. Army has over 101 million square feet of buildings dating to World War II or earlier. Many of these structures were built before the 1978 ban on lead based paints. The U.S. Army Corps of Engineers CERL is developing technologies to remove and stabilize lead containing organic coatings. Promising results have been achieved using a patented flame spray process thatmore » utilizes a glass frit to stabilize the hazardous constituents. When the glass frit is sprayed onto the paint containing substrate, differences in thermal expansion coefficients between the frit and the paint results in spalling of the paint from the substrate surface. The removed fragments are then collected and remelted to stabilize the hazardous constituents and allow for disposal as non-hazardous waste. Similar successful results using a patented process involving microwave technology for paint removal have also been achieved. In this process, the painted surface is coated with a microwave coupling compound that when exposed to microwave energy results in the spalling of the hazardous paint from the surface. The fragments can again be accumulated and remelted for stabilization and disposal.« less

ENVIORNMENTAL TECHNOLOGY VERIFICATION REPORT: ANEST IWATA CORPORATION LPH400-LV HVLP SPRAY GUN

EPA Science Inventory

This Enviornmental Technology Verification reports on the characteristics of a paint spray gun. The research showed that the spray gun provided absolute and relative increases in transfer efficiency over the base line and provided a reduction in the use of paint.

Water-Based Pressure-Sensitive Paints

NASA Technical Reports Server (NTRS)

Jordan, Jeffrey D.; Watkins, A. Neal; Oglesby, Donald M.; Ingram, JoAnne L.

2006-01-01

Water-based pressure-sensitive paints (PSPs) have been invented as alternatives to conventional organic-solvent-based pressure-sensitive paints, which are used primarily for indicating distributions of air pressure on wind-tunnel models. Typically, PSPs are sprayed onto aerodynamic models after they have been mounted in wind tunnels. When conventional organic-solvent-based PSPs are used, this practice creates a problem of removing toxic fumes from inside the wind tunnels. The use of water-based PSPs eliminates this problem. The waterbased PSPs offer high performance as pressure indicators, plus all the advantages of common water-based paints (low toxicity, low concentrations of volatile organic compounds, and easy cleanup by use of water).

Inhalation exposure to isocyanates of car body repair shop workers and industrial spray painters.

PubMed

Pronk, Anjoeka; Tielemans, Erik; Skarping, Gunnar; Bobeldijk, Ivana; VAN Hemmen, Joop; Heederik, Dick; Preller, Liesbeth

2006-01-01

As part of a large-scale epidemiological study, occupational isocyanate exposure was assessed in spray-painting environments. The aim was to assess which compounds contribute to isocyanate exposure in car body repair shops and industrial painting companies, and to identify tasks with high risk of isocyanate exposure. Mainly personal task-based samples (n = 566) were collected from 24 car body repair shops and five industrial painting companies using impingers with DBA in toluene. Samples were analysed by LC-MS for isocyanate monomers, oligomers and products of thermal degradation. From the 23 analysed compounds, 20 were detected. Exploratory factor analysis resulted in a HDI, TDI and MDI factor with the thermal degradation products divided over the TDI and MDI factors. The HDI factor mainly consisted of HDI oligomers and was dominant in frequency and exposure levels in both industries. Spray painting of PU lacquers resulted in the highest exposures for the HDI factor (spray painting was large with a variability over time of (ww)S(2) = 9.1 compared with between-worker variability of (bw)S(2) = 1.6. Lower level exposure to the HDI factor was found during other painting-related tasks and even tasks without direct exposure to paint. Exposure to the TDI factor was found more regularly in car body repair shops than in industrial painting companies. Exposure levels were low (spraying and welding in car body repair shops (paint is the most important source and major contributor of isocyanate exposure in both industries with highest exposures during PU spraying. However, since respiratory protection is less extensively used during other

Isocyanate Exposure Below Analytical Detection When a Paint Brush and Roller Are Used to Apply Moisture-Cure Polyurethane Paint.

PubMed

Reeb-Whitaker, Carolyn K; Schoonover, Todd M

2016-05-01

Isocyanate exposure is known to be hazardous when polyurethane paints are applied with a spray gun, but less is known of exposure when paint is applied with a paint brush and roller. Concentrations of 1,6-hexamethylene diisocyanate (HDI) monomer and three HDI polymers were assessed when two moisture-cure polyurethane paints containing 31-35% isocyanates were applied with a paint roller and brush. Short-term 15-min samples were taken during paint application in an indoor test environment with no ventilation (n= 12); in an outdoor test environment (n= 11); and in an outdoor in-situ assessment (n= 22). The outdoor in-situ assessment involved the painting of a bus shelter and light poles at a public transit station over two night shifts. All isocyanate samples were below analytical detection. The analytical limits of detection for HDI monomer, HDI biuret, HDI isocyanurate, and HDI uretdione were 0.005, 0.84, 0.87, and 0.88 µg, respectively. The finding that isocyanate concentrations were below detection is attributed to the use of paint roller and brush which minimize paint aerosolization and the paint formulation itself which contained <1% of volatile HDI monomer. © The Author 2016. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Environmental lead exposure to toll booth workers in Hong Kong

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tan, T.C.; Wong, L.T.L.; Lam, C.W.K.

1988-01-01

A survey of workers in the Lion Rock Tunnel toll booths was conducted, as they were regarded as a high risk group in lead exposure due to high density of vehicular traffic. The exposure of the workers to lead was determined by continuous sapling of air around the breathing zone of workers inside the booths. Blood lead concentration of 50 workers showed a mean of 0.65 {mu}mol/L and the mean urine lead concentration was 0.14 {mu}mol/L. Other tests, such as urinary amino-levulinic acid (ALA), erythrocyte zinc protoporphyrin (ZnPP) and hemoglobin concentration (Hb), were also preformed. The blood lead concentrations andmore » other biological parameters of the toll-booth workers were acceptable and may be attributed to the recent legislation to lower the lead content in petrol and to the good preventive measures taken by the management.« less

Development of Universal Portable Spray Stand for Touch-Up Process in The Automotive Paintshop

NASA Astrophysics Data System (ADS)

Fatah Muhamed Mukhtar, Muhamed Abdul; Mohideen Shahul Hameed, Rasool

2016-02-01

A spray stand is a custom-made tool used to hold the automotive body parts as well as the devices used to facilitate the operator during the Touch Up process in Paint shop production. This paper discusses about the development of Universal Portable Spray Stand (UPSS) as a tool to hold various types of automotive body parts and model of car during the painting process. The main objective of this study is to determine the effective application of UPSS at the International College of Automotive (ICAM) and also in the automotive industry. This will be helpful to add features to the current spray stand in ICAM and to add value to the spray stand based on selected criteria which are universal, portable and cost saving. In addition, study in the UPSS is also expected to bring reduction in cycle time during the touch up process, in the paint defects and in the ergonomics issues among the operators.

Pure-tone audiometry outside a sound booth using earphone attentuation, integrated noise monitoring, and automation.

PubMed

Swanepoel, De Wet; Matthysen, Cornelia; Eikelboom, Robert H; Clark, Jackie L; Hall, James W

2015-01-01

Accessibility of audiometry is hindered by the cost of sound booths and shortage of hearing health personnel. This study investigated the validity of an automated mobile diagnostic audiometer with increased attenuation and real-time noise monitoring for clinical testing outside a sound booth. Attenuation characteristics and reference ambient noise levels for the computer-based audiometer (KUDUwave) was evaluated alongside the validity of environmental noise monitoring. Clinical validity was determined by comparing air- and bone-conduction thresholds obtained inside and outside the sound booth (23 subjects). Twenty-three normal-hearing subjects (age range, 20-75 years; average age 35.5) and a sub group of 11 subjects to establish test-retest reliability. Improved passive attenuation and valid environmental noise monitoring was demonstrated. Clinically, air-conduction thresholds inside and outside the sound booth, corresponded within 5 dB or less > 90% of instances (mean absolute difference 3.3 ± 3.2 SD). Bone conduction thresholds corresponded within 5 dB or less in 80% of comparisons between test environments, with a mean absolute difference of 4.6 dB (3.7 SD). Threshold differences were not statistically significant. Mean absolute test-retest differences outside the sound booth was similar to those in the booth. Diagnostic pure-tone audiometry outside a sound booth, using automated testing, improved passive attenuation, and real-time environmental noise monitoring demonstrated reliable hearing assessments.

What Tension between Fidelity and Cultural Adaptation? A Reaction to Marsiglia and Booth

ERIC Educational Resources Information Center

Sampson, McClain; Torres, Luis R.

2015-01-01

This paper is a reaction to Marsiglia and Booths' paper, "Cultural Adaptation of Interventions in Real Practice Settings." In their paper, Marsiglia and Booth present the difficulty of implementing and replicating evidence-supported treatments, such as randomized clinical trials, among culturally diverse clients. Practitioners working in…

Volatile Organic Compound and Particulate Emission Studies of AF (Air Force) Paint Booth Facilities. Phase 1.

DTIC Science & Technology

1988-07-01

quantity of air which requires processing. Recirculation systems were designed for two of the painting facilities included in this study. In designing the...BACKGROUND AND PURPOSE .... ................ .... 57 B. DESIGN CONSIDERATIONS .... ............... .... 58 1. Safety Standards .......... ............... 58...65 5. Conceptual Design .... ................ ... 68 V CONCLUSIONS AND RECOMMENDATIONS ............... .. 72 A. CONCLUSIONS

77 FR 40550 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Revision for the Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-10

... filtered spray booth and enclosed spray gun cleaner. Maryland's 1997 SIP-approved regulation COMAR 26.11.19... equipment and materials storage such as spray booths, spray guns, and sealed containers for cleaning rags... standards include procedures for cleaning the spray gun equipment for applying automotive coatings. Affected...

An evaluation of two flat-black silicone paints for space application

NASA Technical Reports Server (NTRS)

Clatterbuck, Carroll H.; Scialdone, John J.

1990-01-01

Tests were conducted on two flat-black silicone paints suggested for space applications to determine their optical, electrical, and mechanical properties. Three different types of substrate materials were chosen for these paint tests; the application of the paints onto the primed substrates was carried out by spray coating. The adhesion properties were verified by thermal shock and sudden immersion into liquid nitrogen. A controlled thermal vacuum tests was also carried out by varying the temperature of the paint from -100 to 225 C. The measured optical properties included normal and hemispherical emittance, and solar absorption/reflectance. A simultaneous exposure to low-energy proton/UV irradiation in vacuum, and high-energy proton/electron irradiation was carried out. Additional tests of the paints are described.

MEASUREMENTS OF VOLATILE ORGANIC COMPOUNDS AND PARTICLES DURING APPLICATION OF LATEX PAINT WITH AN AIRLESS SPRAYER

EPA Science Inventory

The paper discusses experiments, conducted at EPA's Indoor Air Quality Research House, to measure airborne concentrations of volatile organic compounds (VOCs) and particles during and following the spray-application of latex wall paint. (NOTE: Paint may be applied indoors by a v...

Cancer mortality among workers exposed to zinc chromate paints.

PubMed

Dalager, N A; Mason, T J; Fraumeni, J F; Hoover, R; Payne, W W

1980-01-01

To evaluate the carcinogenicity of chromium compounds among user industries, the proportionate mortality experience of spray painters exposed to zinc chromate primer paints and electroplaters exposed to chromic acid in the aircraft maintenance industry was examined. Compared to the mortality patterns of U.S. white males, no excess of cancer was found in the 48 deaths among electroplaters. Analysis of the 202 deaths among spray painters revealed a significant excess of cancer, primarily of the respiratory tract. The relative increase of respiratory cancer showed a positive gradient with the length of estimated exposure time, and was confined to painters whose interval from first employment to death was at least 20 years. The findings consistent with occupational exposure to chromium compounds, previously shown to be carcinogenic in manufacturing processes, but the effect of other paint constituents, tobacco smoking, or methodologic limitations could not be discounted.

2016 National Training Conference Exhibit Booths and Poster Displays

EPA Pesticide Factsheets

Exhibit Booths and Poster Displays for the 2016 National Training Conference on the Toxics Release Inventory (TRI) and Environmental Conditions in Communities. Identifies presentation topics and speakers for October 19 and 20.

Compliance with the Aerospace MACT Standard at Lockheed Martin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurucz, K.L.; Vicars, S.; Fetter, S.

1997-12-31

Actions taken and planned at four Lockheed Martin Corporation (LMC) facilities to comply with the Aerospace MACT Standard are reviewed. Many LMC sites have taken proactive steps to reduce emissions and implement low VOC coating technology. Significant administrative, facility, and material challenges remain to achieve compliance with the upcoming NESHAP and Control Technology Guideline (CTG) standards. The facilities discussed herein set up programs to develop and implement compliance strategies. These facilities manufacture military aircraft, missiles, satellites, rockets, and electronic guidance and communications systems. Some of the facilities are gearing up for new production lines subject to new source MACT standards.more » At this time the facilities are reviewing compliance status of all primers, topcoats, maskants and solvents subject to the standard. Facility personnel are searching for the most efficient methods of satisfying the recordkeeping, reporting and monitoring, sections of the standards while simultaneously preparing or reviewing their Title V permit applications. Facility decisions on paint booths are the next highest priority. Existing dry filter paint booths will be subject to the filtration standard for existing paint booths which requires the use of two-stage filters. Planned paint booths for the F-22 program, and other new booths must comply with the standard for new and rebuilt booths which requires three stage or HEPA filters. Facilities looking to replace existing water wash paint booths, and those required to retrofit the air handling equipment to accommodate the two-stage filters, are reviewing issues surrounding the rebuilt source definition.« less

Effect of ventilation velocity on hexavalent chromium and isocyanate exposures in aircraft paint spraying.

PubMed

Bennett, James; Marlow, David; Nourian, Fariba; Breay, James; Feng, Amy; Methner, Mark

2018-03-01

Exposure control system performance was evaluated during aircraft paint spraying at a military facility. Computational fluid dynamics (CFD) modeling, tracer gas testing, and exposure monitoring examined contaminant exposure vs. crossflow ventilation velocity. CFD modeling using the RNG k-ϵ turbulence model showed exposures to simulated methyl isobutyl ketone of 294 and 83.6 ppm, as a spatial average of five worker locations, for velocities of 0.508 and 0.381 m/s (100 and 75 fpm), respectively. In tracer gas experiments, observed supply/exhaust velocities of 0.706/0.503 m/s (136/99 fpm) were termed full-flow, and reduced velocities were termed 3/4-flow and half-flow. Half-flow showed higher tracer gas concentrations than 3/4-flow, which had the lowest time-averaged concentration, with difference in log means significant at the 95% confidence level. Half-flow compared to full-flow and 3/4-flow compared to full-flow showed no statistically significant difference. CFD modeling using these ventilation conditions agreed closely with the tracer results for the full-flow and 3/4-flow comparison, yet not for the 3/4-flow and half-flow comparison. Full-flow conditions at the painting facility produced a velocity of 0.528 m/s (104 fpm) midway between supply and exhaust locations, with the supply rate of 94.4 m 3 /s (200,000 cfm) exceeding the exhaust rate of 68.7 m 3 /s (146,000 cfm). Ventilation modifications to correct this imbalance created a midhangar velocity of 0.406 m/s (80.0 fpm). Personal exposure monitoring for two worker groups-sprayers and sprayer helpers ("hosemen")-compared process duration means for the two velocities. Hexavalent chromium (Cr[VI]) exposures were 500 vs. 360 µg/m 3 for sprayers and 120 vs. 170 µg/m 3 for hosemen, for 0.528 m/s (104 fpm) and 0.406 m/s (80.0 fpm), respectively. Hexamethylene diisocyanate (HDI) monomer means were 32.2 vs. 13.3 µg/m 3 for sprayers and 3.99 vs. 8.42 µg/m 3 for hosemen. Crossflow

Determinants of isocyanate exposures in auto body repair and refinishing shops.

PubMed

Woskie, S R; Sparer, J; Gore, R J; Stowe, M; Bello, D; Liu, Y; Youngs, F; Redlich, C; Eisen, E; Cullen, M

2004-07-01

As part of the Survey of Painters and Repairers of Auto bodies by Yale (SPRAY), the determinants of isocyanate exposure in auto body repair shops were evaluated. Measurements (n = 380) of hexamethylene diisocyanate-based monomer and polyisocyanate and isophorone diisocyanate-based polyisocyanate were collected from 33 auto body shops. The median total reactive isocyanate concentrations expressed as mass concentration of the NCO functional group were: 206 microg NCO/m3 for spray operations; 0.93 microg NCO/m3 for samples collected in the vicinity of spray operations done on the shop floor (near spray); 0.05 microg NCO/m3 for office or other shop areas adjacent to spray areas (workplace background); 0.17 microg NCO/m3 for paint mixing and gun cleaning operations (mixing); 0.27 microg NCO/m3 for sanding operations. Exposure determinants for the sample NCO mass load were identified using linear regression, tobit regression and logistic regression models. For spray samples in a spray booth the significant determinants were the number of milliliters of NCO applied, the gallons of clear coat used by the shop each month and the type of spray booth used (custom built crossdraft, prefabricated crossdraft or downdraft/semi-downdraft). For near spray (bystander) samples, outdoor temperature >65 degrees F (18 degrees C) and shop size >5000 feet2 (465 m2) were significant determinants of exposure levels. For workplace background samples the shop annual income was the most important determinant. For sanding samples, the shop annual income and outdoor temperature >65 degrees F (18 degrees C) were the most significant determinants. Identification of these key exposure determinants will be useful in targeting exposure evaluation and control efforts to reduce isocyanate exposures.

INTERIOR OF ROOF STRUCTURE LOOKING FROM TOP OF PROJECTION BOOTH, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR OF ROOF STRUCTURE LOOKING FROM TOP OF PROJECTION BOOTH, VIEW FACING SOUTH-SOUTHWEST. - Naval Air Station Barbers Point, Theater, Yorktown Avenue between Wasp & Saipan Streets, Ewa, Honolulu County, HI

Understanding Factors that Influence Protective Glove Use among Automotive Spray Painters

PubMed Central

Ceballos, Diana; Reeb-Whitaker, Carolyn; Glazer, Patricia; Murphy-Robinson, Helen; Yost, Michael

2017-01-01

Dermal contact with isocyanate-based coatings may lead to systemic respiratory sensitization. The most common isocyanates found in sprayed automotive coatings are monomeric and oligomeric 1,6-hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI). Most spray painters use thin (4–5 mil) latex gloves that are not effective at preventing dermal exposures when spraying isocyanate paints. Personal interviews with collision repair industry personnel and focus groups with spray painters were held to characterize risk awareness, to examine perceptions and challenges concerning protective glove use and selection, and to generate ideas for protective glove use interventions. The most popular gloves among spray painters were thin (4–5 mil) and thick (14 mil) latex. We found that medium to thick (6–8 mil) nitrile were not always perceived as comfortable and were expected to be more expensive than thin (4–5 mil) latex gloves. Of concern is the users’ difficulty to distinguish between nitrile and latex gloves; latex gloves are now sold in different colors including blue, which has traditionally been associated with nitrile gloves. Even though spray painters were familiar with the health hazards related to working with isocyanate paints; most were not always aware that dermal exposure to isocyanates could contribute to the development of occupational asthma. There is a need for more research to identify dermal materials that are protective against sprayed automotive coatings. Automotive spray painters and their employers need to be educated in the selection and use of protective gloves, specifically on attributes such as glove material, color, and thickness. PMID:24215135

Visitor center museum display, detail of diorama booth with raised ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Visitor center museum display, detail of diorama booth with raised step; door to electrical door panel at left - Wright Brothers National Memorial Visitor Center, Highway 158, Kill Devil Hills, Dare County, NC

[Health survey of painting and coating workers in an automobile manufacturing enterprise in Guangzhou, China].

PubMed

Huang, Lili; Xiao, Lyuwu; Wu, Lin; Zhou, Hao; Tan, Xiayou; Lin, Yimin

2014-04-01

To investigate the health status of painting and coating workers in an automobile manufacturing enterprise in Guangzhou, China and analyze the influential factors for the health status of these workers, and to provide health intervention measures and strategies. Typical sampling was used to select an automobile manufacturing enterprise; according to whether the subjects were in contact with paint and coatings, paint spraying workers in the painting workshop were selected as the exposed group, and the staff in the administration, procurement, and marketing departments as the control group. Physical examination was performed by doctors among these subjects. The exposed group had significantly higher positive rates of dizziness, headache, bleeding gums, chest tightness, and skin itching than the control group (P < 0.05). The exposed group had a nonsignificantly higher rate of abnormal ECG than the control group (P > 0.05), but the exposed group had a significantly higher incidence of various blocks (P = 0.020) and significantly lower leukocyte count, erythrocyte count, and male workers' hemoglobin level (P < 0.05), as compared with the control group. Volatile organic solvents have adverse effect on the health of paint spraying workers in the automobile manufacturing enterprise, so regular physical examination should be performed to strengthen health interventions and improve health.

Degradation of insecticides used for indoor spraying in malaria control and possible solutions

PubMed Central

2011-01-01

Background The insecticide dichloro-diphenyl-trichloroethane (DDT) is widely used in indoor residual spraying (IRS) for malaria control owing to its longer residual efficacy in the field compared to other World Health Organization (WHO) alternatives. Suitable stabilization to render these alternative insecticides longer lasting could provide a less controversial and more acceptable and effective alternative insecticide formulations than DDT. Methods This study sought to investigate the reasons behind the often reported longer lasting behaviour of DDT by exposing all the WHO approved insecticides to high temperature, high humidity and ultra-violet light. Interactions between the insecticides and some mineral powders in the presence of an aqueous medium were also tested. Simple insecticidal paints were made using slurries of these mineral powders whilst some insecticides were dispersed into a conventional acrylic paint binder. These formulations were then spray painted on neat and manure coated mud plaques, representative of the material typically used in rural mud houses, at twice the upper limit of the WHO recommended dosage range. DDT was applied directly onto mud plaques at four times the WHO recommended concentration and on manure plaques at twice WHO recommended concentration. All plaques were subjected to accelerated ageing conditions of 40°C and a relative humidity of 90%. Results The pyrethroids insecticides outperformed the carbamates and DDT in the accelerated ageing tests. Thus UV exposure, high temperature oxidation and high humidity per se were ruled out as the main causes of failure of the alternative insecticides. Gas chromatography (GC) spectrograms showed that phosphogypsum stabilised the insecticides the most against alkaline degradation (i.e., hydrolysis). Bioassay testing showed that the period of efficacy of some of these formulations was comparable to that of DDT when sprayed on mud surfaces or cattle manure coated surfaces. Conclusions

DETAIL, CONTROL BOOTH, RP1 TANK FARM Edwards Air Force ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL, CONTROL BOOTH, RP1 TANK FARM - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Combined Fuel Storage Tank Farm, Test Area 1-120, north end of Jupiter Boulevard, Boron, Kern County, CA

Probing a Spray Using Frequency-Analyzed Light Scattering

NASA Technical Reports Server (NTRS)

Eskridge, Richard; Lee, Michael H.; Rhys, Noah O.

2008-01-01

Frequency-analyzed laser-light scattering (FALLS) is a relatively simple technique that can be used to measure principal characteristics of a sheet of sprayed liquid as it breaks up into ligaments and then the ligaments break up into droplets. In particular, through frequency analysis of laser light scattered from a spray, it is possible to determine whether the laser-illuminated portion of the spray is in the intact-sheet region, the ligament region, or the droplet region. By logical extension, it is possible to determine the intact length from the location of the laser beam at the transition between the intact-sheet and ligament regions and to determine a breakup frequency from the results of the frequency analysis. Hence, FALLS could likely be useful both as a means of performing research on sprays in general and as a means of diagnostic sensing in diverse applications in which liquid fuels are sprayed. Sprays are also used for drying and to deposit paints and other coating materials.

INTERIOR VIEW, LOOKING WEST, WITH PIPE BEING SPRAYED WITH ZINC ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, LOOKING WEST, WITH PIPE BEING SPRAYED WITH ZINC COATING. - United States Pipe & Foundry Company Plant, Coating, Painting, Lining & Packaging Building, 2023 St. Louis Avenue at I-20/59, Bessemer, Jefferson County, AL

Recovery of a Charred Painting Using Atomic Oxygen Treatment

NASA Technical Reports Server (NTRS)

Rutledge, Sharon K.; Banks, Bruce A.; Chichernea, Virgil A.

1999-01-01

A noncontact method is described which uses atomic oxygen to remove soot and char from the surface of a painting. The atomic oxygen was generated by the dissociation of oxygen in low pressure air using radio frequency energy. The treatment, which is an oxidation process, allows control of the amount of material to be removed. The effectiveness of char removal from half of a fire-damaged oil painting was studied using reflected light measurements from selected areas of the painting and by visual and photographic observation. The atomic oxygen was able to effectively remove char and soot from the treated half of the painting. The remaining loosely bound pigment was lightly sprayed with a mist to replace the binder and then varnish was reapplied. Caution should he used when treating an untested paint medium using atomic oxygen. A representative edge or corner should he tested first in order to determine if the process would be safe for the pigments present. As more testing occurs, a greater knowledge base will be developed as to what types of paints and varnishes can or cannot be treated using this technique. With the proper precautions, atomic oxygen treatment does appear to be a technique with great potential for allowing very charred, previously unrestorable art to be salvaged.

The Art of Being Persuaded: Wayne Booth's Mutual Inquiry and the Trust to Listen

ERIC Educational Resources Information Center

Baker, Marsha Lee; Dieter, Eric; Dobbins, Zachary

2014-01-01

This article examines Wayne C. Booth's legacy as a teacher and scholar through the concept of rhetoric as mutual inquiry that he develops from "Modern Dogma and the Rhetoric of Assent" (1974) through "The Rhetoric of Rhetoric" (2004). Booth's work connects the political and pedagogical in pragmatic and productive ways…

Anthropometric data collection of Portuguese children using 3D body scanning: considerations about the scanning booth

NASA Astrophysics Data System (ADS)

de Campos, R.; Carvalho, M. A.; Lopes, H. P.; Xu, B.

2017-10-01

This paper presents some considerations regarding the scanning booth used in an anthropometric study done with a 3D body scanning technology. The data collected is part of a Ph.D. study conducted in Textile Engineering at University of Minho in Portugal, which aims to develop clothing for overweight and obese Portuguese children aged 2-11 years, of both genders. The challenges faced during data collection are described, and modifications of the scanning booth are proposed. It is possible to conclude that the importance of the scanning booth is key to an efficient anthropometric data collection, including the growth of this technology in the garment industry, Universities Research Institutes involved with anthropometric studies.

Highly accurate thickness measurement of multi-layered automotive paints using terahertz technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krimi, Soufiene; Beigang, René; Klier, Jens

2016-07-11

In this contribution, we present a highly accurate approach for thickness measurements of multi-layered automotive paints using terahertz time domain spectroscopy in reflection geometry. The proposed method combines the benefits of a model-based material parameters extraction method to calibrate the paint coatings, a generalized Rouard's method to simulate the terahertz radiation behavior within arbitrary thin films, and the robustness of a powerful evolutionary optimization algorithm to increase the sensitivity of the minimum thickness measurement limit. Within the framework of this work, a self-calibration model is introduced, which takes into consideration the real industrial challenges such as the effect of wet-on-wetmore » spray in the painting process.« less

Quantification and Statistical Modeling—Part I: Breathing-Zone Concentrations of Monomeric and Polymeric 1,6-Hexamethylene Diisocyanate

PubMed Central

Fent, Kenneth W.; Gaines, Linda G. Trelles; Thomasen, Jennifer M.; Flack, Sheila L.; Ding, Kai; Herring, Amy H.; Whittaker, Stephen G.; Nylander-French, Leena A.

2009-01-01

We conducted a repeated exposure-assessment survey for task-based breathing-zone concentrations (BZCs) of monomeric and polymeric 1,6-hexamethylene diisocyanate (HDI) during spray painting on 47 automotive spray painters from North Carolina and Washington State. We report here the use of linear mixed modeling to identify the primary determinants of the measured BZCs. Both one-stage (N = 98 paint tasks) and two-stage (N = 198 paint tasks) filter sampling was used to measure concentrations of HDI, uretidone, biuret, and isocyanurate. The geometric mean (GM) level of isocyanurate (1410 μg m−3) was higher than all other analytes (i.e. GM < 7.85 μg m−3). The mixed models were unique to each analyte and included factors such as analyte-specific paint concentration, airflow in the paint booth, and sampler type. The effect of sampler type was corroborated by side-by-side one- and two-stage personal air sampling (N = 16 paint tasks). According to paired t-tests, significantly higher concentrations of HDI (P = 0.0363) and isocyanurate (P = 0.0035) were measured using one-stage samplers. Marginal R2 statistics were calculated for each model; significant fixed effects were able to describe 25, 52, 54, and 20% of the variability in BZCs of HDI, uretidone, biuret, and isocyanurate, respectively. Mixed models developed in this study characterize the processes governing individual polyisocyanate BZCs. In addition, the mixed models identify ways to reduce polyisocyanate BZCs and, hence, protect painters from potential adverse health effects. PMID:19622637

Quantitative plasma biomarker analysis in HDI exposure assessment.

PubMed

Flack, Sheila L; Fent, Kenneth W; Trelles Gaines, Linda G; Thomasen, Jennifer M; Whittaker, Steve; Ball, Louise M; Nylander-French, Leena A

2010-01-01

Quantification of amines in biological samples is important for evaluating occupational exposure to diisocyanates. In this study, we describe the quantification of 1,6-hexamethylene diamine (HDA) levels in hydrolyzed plasma of 46 spray painters applying 1,6-hexamethylene diisocyanate (HDI)-containing paint in vehicle repair shops collected during repeated visits to their workplace and their relationship with dermal and inhalation exposure to HDI monomer. HDA was detected in 76% of plasma samples, as heptafluorobutyryl derivatives, and the range of HDA concentrations was < or =0.02-0.92 microg l(-1). After log-transformation of the data, the correlation between plasma HDA levels and HDI inhalation exposure measured on the same workday was low (N = 108, r = 0.22, P = 0.026) compared with the correlation between plasma HDA levels and inhalation exposure occurring approximately 20 to 60 days before blood collection (N = 29, r = 0.57, P = 0.0014). The correlation between plasma HDA levels and HDI dermal exposure measured on the same workday, although statistically significant, was low (N = 108, r = 0.22, P = 0.040) while the correlation between HDA and dermal exposure occurring approximately 20 to 60 days before blood collection was slightly improved (N = 29, r = 0.36, P = 0.053). We evaluated various workplace factors and controls (i.e. location, personal protective equipment use and paint booth type) as modifiers of plasma HDA levels. Workers using a downdraft-ventilated booth had significantly lower plasma HDA levels relative to semi-downdraft and crossdraft booth types (P = 0.0108); this trend was comparable to HDI inhalation and dermal exposure levels stratified by booth type. These findings indicate that HDA concentration in hydrolyzed plasma may be used as a biomarker of cumulative inhalation and dermal exposure to HDI and for investigating the effectiveness of exposure controls in the workplace.

Malignant Fibrous Histiocytoma of the Maxillary Sinus in a Spray Painter from an Automobile Repair Shop

PubMed Central

2013-01-01

Background We report a case of a spray painter who developed malignant fibrous histiocytoma (MFH) of the maxillary sinus following long-term exposure to chromium, nickel, and formaldehyde, implying that these agents are probable causal agents of MFH. Case report The patient developed right-sided prosopalgia that began twenty months ago. The symptom persisted despite medical treatment. After two months, he was diagnosed with MFH through imaging studies, surgery, and pathological microscopic findings at a university hospital in Seoul. His social, medical, and family history was unremarkable. The patient had worked for about 18 years at an automobile repair shop as a spray painter. During this period, he had been exposed to various occupational agents, such as hexavalent chromium, nickel, and formaldehyde, without appropriate personal protective equipment. He painted 6 days a week and worked for about 8 hours a day. Investigation of the patient’s work environment detected hexavalent chromium, chromate, nickel, and formaldehyde. Conclusions The study revealed that the patient had been exposed to hexavalent chromium, formaldehyde, and nickel compounds through sanding and spray painting. The association between paranasal cancer and exposure to the aforementioned occupational human carcinogens has been established. We suggest, in this case, the possibility that the paint spraying acted as a causal agent for paranasal cancer. PMID:24472378

Quantification of VOC emissions from paint spraying on a construction site using solid phase microextraction devices.

PubMed

Cheng, Wen-Hsi; Huang, Hsiao-Lin; Chen, Kang-Shin; Chang, Yu-Jen

2017-10-15

The objective of this study was to measure the emission of, and personal exposure to workers, volatile organic compound (VOC) during paint spraying on a construction site. Needle trap samplers (NTSs), which are a green solid phase microextraction sampling technology, were used to obtain air samples at a large music exhibition center. The standard active sampling method using charcoal tubes and a personal air pump, Method 1501, was simultaneously utilized at the sampling sites to assess the workers' VOC exposures. Analysis of the data thus obtained showed that benzene, toluene, ethylenebenzene, and xylenes (BTEXs) were the main emission compounds. Acetone and isobutyl alcohol, which are used as thinning solvents, were detected as minor emission compounds. The emitted concentrations of most compounds were lower than the legal emission limits in Taiwan except that of benzene, for which the 2-ppm time weighted average short-term exposure limit was exceeded. The packed divinylbenzene (DVB) in the NTS was observed under an environmental scanning electron microscope, and many fine aerosols were found to be deposited on the surface of the DVB adsorbents, causing VOC extraction efficiencies after the fifth sampling in the field to decline. Workers on construction sites should be protected from emissions of VOC and fine particulates to preserve their occupational health.

Evaluation of high pressure water blast with rotating spray bar for removing paint and rubber deposits from airport runways, and review of runway slipperiness problems created by rubber contamination

NASA Technical Reports Server (NTRS)

Horne, W. B.; Griswold, G. D.

1975-01-01

A high pressure water blast with rotating spray bar treatment for removing paint and rubber deposits from airport runways is studied. The results of the evaluation suggest that the treatment is very effective in removing above surface paint and rubber deposits to the point that pavement skid resistance is restored to trafficked but uncontaminated runway surface skid resistance levels. Aircraft operating problems created by runway slipperiness are reviewed along with an assessment of the contributions that pavement surface treatments, surface weathering, traffic polishing, and rubber deposits make in creating or alleviating runway slipperiness. The results suggest that conventional surface treatments for both portland cement and asphaltic concrete runways are extremely vulnerable to rubber deposit accretions which can produce runway slipperiness conditions for aircraft operations as or more slippery than many snow and ice-covered runway conditions. Pavement grooving surface treatments are shown to be the least vulnerable to rubber deposits accretion and traffic polishing of the surface treatments examined.

Occupational exposure to organic solvents during paint stripping and painting operations in the aeronautical industry.

PubMed

Vincent, R; Poirot, P; Subra, I; Rieger, B; Cicolella, A

1994-01-01

The exposure of workers to methylene chloride and phenol in an aeronautical workshop was measured during stripping of paint from a Boeing B 747. Methylene chloride exposure was measured during two work days by personal air sampling, while area sampling was used for phenol. During paint stripping operations, methylene chloride air concentrations ranged from 299.2 mg/m3 (83.1 ppm) to 1888.9 mg/m3 (524.7 ppm). The exposures to methylene chloride calculated for an 8-h work day ranged from 86 mg/m3 (23.9 ppm) to 1239.5 mg/m3 (344.3 ppm). In another aeronautical workshop, exposure to organic solvents, especially ethylene glycol monoethylether acetate (EGEEA), was controlled during the painting of an Airbus A 320. The external exposure to solvents and EGEEA was measured by means of individual air sampling. The estimation of internal exposure to EGEEA was made by measuring its urinary metabolite, ethoxyacetic acid (EAA). Both measurements were made during the course of 3 days. The biological samples were taken pre- and post-shift. During painting operations, methyl ethyl ketone, ethyl acetate, n-butyl alcohol, methyl isobutyl ketone, toluene, n-butyl acetate, ethylbenzene, xylenes and EGEEA were detected in working atmospheres. For these solvents, air concentrations ranged from 0.1 ppm to 69.1 ppm. EGEEA concentrations ranged from 29.2 mg/m3 (5.4 ppm) to 150.1 mg/m3 (27.8 ppm). For biological samples, the average concentrations of EAA were 108.4 mg/g creatinine in pre-shift and 139.4 mg/g creatinine in post-shift samples. Despite the fact that workers wore protective respiratory equipment during paint spraying operations, EEA urinary concentrations are high and suggest that percutaneous uptake is the main route of exposure for EGEEA.(ABSTRACT TRUNCATED AT 250 WORDS)

TOILET ROOM IN THE PROJECTION BOOTH. NOTE THE HEXAGONAL FLOOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

TOILET ROOM IN THE PROJECTION BOOTH. NOTE THE HEXAGONAL FLOOR TILES WITH ACCENTED BORDER AND GLAZED WALL TILES, ALL OF WHICH WERE ORIGINAL/ TYPICAL IN TOILET ROOMS IN THIS FACILITY VIEW FACING NORTHWEST - U.S. Naval Base, Pearl Harbor, Theater, Hornet Avenue between Enterprise & Pokomoke Streets, Pearl City, Honolulu County, HI

Workplace safety and health programs, practices, and conditions in auto collision repair businesses.

PubMed

Brosseau, L M; Bejan, A; Parker, D L; Skan, M; Xi, M

2014-01-01

This article describes the results of a pre-intervention safety assessment conducted in 49 auto collision repair businesses and owners' commitments to specific improvements. A 92-item standardized audit tool employed interviews, record reviews, and observations to assess safety and health programs, training, and workplace conditions. Owners were asked to improve at least one-third of incorrect, deficient, or missing (not in compliance with regulations or not meeting best practice) items, of which a majority were critical or highly important for ensuring workplace safety. Two-thirds of all items were present, with the highest fraction related to electrical safety, machine safety, and lockout/tagout. One-half of shops did not have written safety programs and had not conducted recent training. Many had deficiencies in respiratory protection programs and practices. Thirteen businesses with a current or past relationship with a safety consultant had a significantly higher fraction of correct items, in particular related to safety programs, up-to-date training, paint booth and mixing room conditions, electrical safety, and respiratory protection. Owners selected an average of 58% of recommended improvements; they were most likely to select items related to employee Right-to-Know training, emergency exits, fire extinguishers, and respiratory protection. They were least likely to say they would improve written safety programs, stop routine spraying outside the booth, or provide adequate fire protection for spray areas outside the booth. These baseline results suggest that it may be possible to bring about workplace improvements using targeted assistance from occupational health and safety professionals.

The Influence of Shaping Air Pressure of Pneumatic Spray Gun

NASA Astrophysics Data System (ADS)

Chen, Wenzhuo; Chen, Yan; Pan, Haiwei; Zhang, Weiming; Li, Bo

2018-02-01

The shaping air pressure is a very important parameter in the application of pneumatic spray gun, and studying its influence on spray flow field and film thickness distribution has practical values. In this paper, Euler-Lagrangian method is adopted to describe the two-phase spray flow of pneumatic painting process, and the air flow fields, spray patterns and dynamic film thickness distributions were obtained with the help of the computational fluid dynamics code—ANSYS Fluent. Results show that with the increase of the shaping air pressure, the air phase flow field spreads in the plane perpendicular to the shaping air hole plane, the spray pattern becomes narrower and flatter, and the width of the dynamic film increases with the reduced maximum value of the film thickness. But the film thickness distribution seems to change little with the shaping air pressure decreasing from 0.6bar to 0.9bar.

London through Rose-Colored Graphics: Visual Rhetoric and Information Graphic Design in Charles Booth's Maps of London Poverty

ERIC Educational Resources Information Center

Kimball, Miles A.

2006-01-01

In this article, I examine a historical information graphic--Charles Booth's maps of London poverty (1889-1902)--to analyze the cultural basis of ideas of transparency and clarity in information graphics. I argue that Booth's maps derive their rhetorical power from contemporary visual culture as much as from their scientific authority. The visual…

Going wireless and booth-less for hearing testing in industry.

PubMed

Meinke, Deanna K; Norris, Jesse A; Flynn, Brendan P; Clavier, Odile H

2017-01-01

To assess the test-retest variability of hearing thresholds obtained with an innovative, mobile wireless automated hearing-test system (WAHTS) with enhanced sound attenuation to test industrial workers at a worksite as compared to standardised automated hearing thresholds obtained in a mobile trailer sound booth. A within-subject repeated-measures design was used to compare air-conducted threshold tests (500-8000 Hz) measured with the WAHTS in six workplace locations, and a third test using computer-controlled audiometry obtained in a mobile trailer sound booth. Ambient noise levels were measured in all test environments. Twenty workers served as listeners and 20 workers served as operators. On average, the WAHTS resulted in equivalent thresholds as the mobile trailer audiometry at 1000, 2000, 3000 and 8000 Hz and thresholds were within ±5 dB at 500, 4000 and 6000 Hz. Comparable performance may be obtained with the WAHTS in occupational audiometry and valid thresholds may be obtained in diverse test locations without the use of sound-attenuating enclosures.

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

40 CFR 60.391 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... truck including hoods, fenders, cargo boxes, doors, and grill opening panels. Bake oven means a device...-duty truck assembly lines between the coating application system (dip tank or spray booth) and the bake oven. Guide coat operation means the guide coat spray booth, flash-off area and bake oven(s) which are...

Effect of illumination on colour vision testing with Farnsworth-Munsell 100 hue test: customized colour vision booth versus room illumination.

PubMed

Zahiruddin, Kowser; Banu, Shaj; Dharmarajan, Ramya; Kulothungan, Vaitheeswaran; Vijayan, Deepa; Raman, Rajiv; Sharma, Tarun

2010-06-01

To evaluate a customized, portable Farnsworth-Munsell 100 (FM 100) hue viewing booth for compliance with colour vision testing standards and to compare it with room illumination in subjects with normal colour vision (trichromats), subjects with acquired colour vision defects (secondary to diabetes mellitus), and subjects with congenital colour vision defects (dichromats). Discrete wavelengths of the tube in the customized booth were measured using a spectrometer using the normal incident method and were compared with the spectral distribution of sunlight. Forty-eight subjects were recruited for the study and were divided into 3 groups: Group 1, Normal Trichromats (30 eyes); Group 2, Congenital Colour Vision Defects (16 eyes); and Group 3, Diabetes Mellitus (20 eyes). The FM 100 hue test performance was compared using two illumination conditions, booth illumination and room illumination. Total error scores of the classical method in Group 2 as mean+/-SD for room and booth illumination was 243.05+/-85.96 and 149.85+/-54.50 respectively (p=0.0001). Group 2 demonstrated lesser correlation (r=0.50, 0.55), lesser reliability (Cronbach's alpha, 0.625, 0.662) and greater variability (Bland & Altman value, 10.5) in total error scores for the classical method and the moment of inertia method between the two illumination conditions when compared to the other two groups. The customized booth demonstrated illumination meeting CIE standards. The total error scores were overestimated by the classical and moment of inertia methods in all groups for room illumination compared with booth illumination, however overestimation was more significant in the diabetes group.

In Tune with Play and Therapy an Interview with Phyllis Booth

ERIC Educational Resources Information Center

American Journal of Play, 2015

2015-01-01

Phyllis Booth is a licensed marriage and family therapist, a licensed clinical professional counselor, a registered play therapist and supervisor, and Clinical Director Emeritus of the Theraplay Institute in Evanston, Illinois. Her professional career includes training in clinical psychology at what is now University of Chicago Medicine, teaching…

Silica dust, diesel exhaust, and painting work are the significant occupational risk factors for lung cancer in nonsmoking Chinese men

PubMed Central

Tse, L A; Yu, IT-s; Au, J S K; Qiu, H; Wang, X-r

2011-01-01

Background: Few epidemiological studies have explored the associations between occupational exposures and lung cancer in lifelong nonsmoking men. Methods: We obtained lifetime occupational history and other relevant information for 132 newly diagnosed lung cancer cases among nonsmoking Chinese men and 536 nonsmoking community referents. Unconditional multiple logistic regression analysis was performed to estimate the odds ratio (OR) of lung cancer for specific occupational exposures. Results: Significantly increased lung cancer risk was found for nonsmoking workers occupationally exposed to silica dust (OR=2.58, 95% confidence interval (CI): 1.11, 6.01), diesel exhaust (OR=3.47, 95% CI: 1.08, 11.14), spray painting (OR=2.81, 95% CI: 1.14, 6.93), and nonspray painting work (OR=2.36, 95% CI: 1.04, 5.37). Silica dust exposure was associated with a significantly increased risk of adenocarcinoma (OR=2.91, 95% CI: 1.10, 7.68). We observed a positive gradient of all lung cancers and of adenocarcinoma with duration of employment for workers exposed to silica dust and spray painting. Conclusion: This study found an increased risk of lung cancer among nonsmoking Chinese men occupationally exposed to silica dust, diesel exhaust, and painting work. PMID:21102581

Silica dust, diesel exhaust, and painting work are the significant occupational risk factors for lung cancer in nonsmoking Chinese men.

PubMed

Tse, L A; Yu, It-S; Au, J S K; Qiu, H; Wang, X-R

2011-01-04

Few epidemiological studies have explored the associations between occupational exposures and lung cancer in lifelong nonsmoking men. We obtained lifetime occupational history and other relevant information for 132 newly diagnosed lung cancer cases among nonsmoking Chinese men and 536 nonsmoking community referents. Unconditional multiple logistic regression analysis was performed to estimate the odds ratio (OR) of lung cancer for specific occupational exposures. Significantly increased lung cancer risk was found for nonsmoking workers occupationally exposed to silica dust (OR=2.58, 95% confidence interval (CI): 1.11, 6.01), diesel exhaust (OR=3.47, 95% CI: 1.08, 11.14), spray painting (OR=2.81, 95% CI: 1.14, 6.93), and nonspray painting work (OR=2.36, 95% CI: 1.04, 5.37). Silica dust exposure was associated with a significantly increased risk of adenocarcinoma (OR=2.91, 95% CI: 1.10, 7.68). We observed a positive gradient of all lung cancers and of adenocarcinoma with duration of employment for workers exposed to silica dust and spray painting. This study found an increased risk of lung cancer among nonsmoking Chinese men occupationally exposed to silica dust, diesel exhaust, and painting work.

Ocular injury with high-pressure paint: a case report.

PubMed

Bandyopadhyay, Chitrabhanu; Mitra, Arjit; Harrison, Rosalind J

2009-01-01

Chemical injury to the eye is an ophthalmic emergency that can be caused by a work-related accident or common household products. Uradil SZ261 G3Z-65 is a resin containing butyl gycol (2-butoxyethanol) and ethyl ethanol amine (2-dimethyaminoethanol). It is used in stoving enamels for interior and exterior use. The authors report a case of ocular surface injury with a highpressure industrial spray paint-Waterborne Stoving Gentian Blue containing Uradil.

EVALUATION OF SUPERCRITICAL CARBON DIOXIDE TECHNOLOGY TO REDUCE SOLVENT IN SPRAY COATING APPLICATIONS

EPA Science Inventory

This evaluation, part of the Pollution Prevention Clean Technology Demonstration (CTD) Program, addresses the product quality, waste reduction, and economic issues of spray paint application using supercritical carbon dioxide (CO2). Anion Carbide has developed this technology and...

Computer analysis of ATR-FTIR spectra of paint samples for forensic purposes

NASA Astrophysics Data System (ADS)

Szafarska, Małgorzata; Woźniakiewicz, Michał; Pilch, Mariusz; Zięba-Palus, Janina; Kościelniak, Paweł

2009-04-01

A method of subtraction and normalization of IR spectra (MSN-IR) was developed and successfully applied to extract mathematically the pure paint spectrum from the spectrum of paint coat on different bases, both acquired by the Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) technique. The method consists of several stages encompassing several normalization and subtraction processes. The similarity of the spectrum obtained with the reference spectrum was estimated by means of the normalized Manhattan distance. The utility and performance of the method proposed were tested by examination of five different paints sprayed on plastic (polyester) foil and on fabric materials (cotton). It was found that the numerical algorithm applied is able - in contrast to other mathematical approaches conventionally used for the same aim - to reconstruct a pure paint IR spectrum effectively without a loss of chemical information provided. The approach allows the physical separation of a paint from a base to be avoided, hence a time and work-load of analysis to be considerably reduced. The results obtained prove that the method can be considered as a useful tool which can be applied to forensic purposes.

Wire-Arc-Sprayed Aluminum Protects Steel Against Corrosion

NASA Technical Reports Server (NTRS)

Zimmerman, Frank R.; Poorman, Richard; Sanders, Heather L.; Mckechnie, Timothy N.; Bonds, James W., Jr.; Daniel, Ronald L., Jr.

1995-01-01

Aluminum coatings wire-arc sprayed onto steel substrates found effective in protecting substrates against corrosion. Coatings also satisfy stringent requirements for adhesion and flexibility, both at room temperature and at temperatures as low as liquid hydrogen. Developed as alternatives to corrosion-inhibiting primers and paints required by law to be phased out because they contain and emit such toxic substances as chromium and volatile organic compounds.

Constrained Response Surface Optimisation and Taguchi Methods for Precisely Atomising Spraying Process

NASA Astrophysics Data System (ADS)

Luangpaiboon, P.; Suwankham, Y.; Homrossukon, S.

2010-10-01

This research presents a development of a design of experiment technique for quality improvement in automotive manufacturing industrial. The quality of interest is the colour shade, one of the key feature and exterior appearance for the vehicles. With low percentage of first time quality, the manufacturer has spent a lot of cost for repaired works as well as the longer production time. To permanently dissolve such problem, the precisely spraying condition should be optimized. Therefore, this work will apply the full factorial design, the multiple regression, the constrained response surface optimization methods or CRSOM, and Taguchi's method to investigate the significant factors and to determine the optimum factor level in order to improve the quality of paint shop. Firstly, 2κ full factorial was employed to study the effect of five factors including the paint flow rate at robot setting, the paint levelling agent, the paint pigment, the additive slow solvent, and non volatile solid at spraying of atomizing spraying machine. The response values of colour shade at 15 and 45 degrees were measured using spectrophotometer. Then the regression models of colour shade at both degrees were developed from the significant factors affecting each response. Consequently, both regression models were placed into the form of linear programming to maximize the colour shade subjected to 3 main factors including the pigment, the additive solvent and the flow rate. Finally, Taguchi's method was applied to determine the proper level of key variable factors to achieve the mean value target of colour shade. The factor of non volatile solid was found to be one more additional factor at this stage. Consequently, the proper level of all factors from both experiment design methods were used to set a confirmation experiment. It was found that the colour shades, both visual at 15 and 45 angel of measurement degrees of spectrophotometer, were nearly closed to the target and the defective at

Transparent electrodes made with ultrasonic spray coating technique for flexible heaters

NASA Astrophysics Data System (ADS)

Wroblewski, G.; Krzemiński, J.; Janczak, D.; Sowiński, J.; Jakubowska, M.

2017-08-01

Transparent electrodes are one of the basic elements of various electronic components. The paper presents the preliminary results related to novel method of ultrasonic spray coating used for fabrication of transparent flexible electrodes. Experiments were conducted by means of specially made laboratory setup composed of ultrasonic spray generator and XYZ plotter. In the first part of the paper diverse solvents were used to determine the crucial technological parameters such as atomization voltage and fluid flow velocity. Afterwards paint containing carbon nanotubes suspended in the two solvent system was prepared and deposited on the polyethylene terephthalate foil. Thickness, roughness and electrical measurements were performed to designate the relations of technological parameters of ultrasonic spray coating on thickness, roughness, sheet resistance and optical transmission of fabricated samples.

Application of the Booth-Kautzmann method for the determination of N-2 packing leakage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burkhart, D.M.; Milton, J.W.; Fawcett, S.T.

1995-06-01

To accurately determine turbine cycle heat rate, leakage past the N-2 steam seal packing must be determined on turbines with both HP and IP turbines contained within a common high pressure casing. N-2 packing leakage can be determined by the Booth-Kautzmann Method with instrumentation commonly used to determine the HP and IP turbine efficiency. The only additional requirements are changes to the main steam and/or hot reheat steam conditions. This paper discusses the actual test results using the Booth-Kautzmann test procedure on three natural gas fired units. The test results demonstrate the added advantage of having at least three N-2more » test runs, stability requirements for repeatable test runs and test procedures used to determine leakage results. Discussion of the sensitivity of the assumed N-2 enthalpy are also addressed. Utilizing Martins Formula with a series of N-2 Leakage test runs is shown to be a leakage prediction tool and a packing clearance approximation tool. It is concluded that the Booth-Kautzmann Method for determination of N-2 packing leakage should be utilized whenever HP and Ip turbine efficiency is determined. The two or three additional hours invested in the test runs is well worth the information gained on the performance of the N-2 packing.« less

Dermal, inhalation, and internal exposure to 1,6-HDI and its oligomers in car body repair shop workers and industrial spray painters.

PubMed

Pronk, A; Yu, F; Vlaanderen, J; Tielemans, E; Preller, L; Bobeldijk, I; Deddens, J A; Latza, U; Baur, X; Heederik, D

2006-09-01

To study inhalation and dermal exposure to hexamethylene diisocyanate (HDI) and its oligomers as well as personal protection equipment (PPE) use during task performance in conjunction with urinary hexamethylene diamine (HDA) in car body repair shop workers and industrial spray painters. Personal task based inhalation samples (n = 95) were collected from six car body repair shops and five industrial painting companies using impingers with di-n-butylamine (DBA) in toluene. In parallel, dermal exposure was assessed using nitril rubber gloves. Gloves were submerged into DBA in toluene after sampling. Analysis for HDI and its oligomers was performed by LC-MS/MS. Urine samples were collected from 55 workers (n = 291) and analysed for HDA by GC-MS. Inhalation exposure was strongly associated with tasks during which aerosolisation occurs. Dermal exposure occurred during tasks that involve direct handling of paint. In car body repair shops associations were found between detectable dermal exposure and glove use (odds ratio (OR) 0.22, 95% confidence interval (CI) 0.09 to 0.57) and inhalation exposure level (OR 1.34, 95% CI 0.97 to 1.84 for a 10-fold increase). HDA in urine could be demonstrated in 36% and 10% of car body repair shop workers and industrial painting company workers respectively. In car body repair shops, the frequency of detectable HDA was significantly elevated at the end of the working day (OR 2.13, 95% CI 1.07 to 4.22 for 3-6 pm v 0-8 am). In both branches HDA was detected in urine of approximately 25% of the spray painters. In addition HDA was detected in urine of a large proportion of non-spray painters in car body repair shops. Although (spray) painting with lacquers containing isocyanate hardeners results in the highest external exposures to HDI and oligomers, workers that do not perform paint related tasks may also receive a considerable internal dose.

The Booth Sitters of Santa Fe's Indian Market: Making and Maintaining Authenticity

ERIC Educational Resources Information Center

Bernstein, Bruce

2007-01-01

In this article, the author addresses the burden of non-Native expectation on Native artists, highlighting issues of authenticity, creation, and public display. The author writes about the booth sitters hired by collectors to sit--sometimes all night--and wait for the official opening of the annual Indian Market in Santa Fe, New Mexico. He focuses…

Dermal, inhalation, and internal exposure to 1,6‐HDI and its oligomers in car body repair shop workers and industrial spray painters

PubMed Central

Pronk, A; Yu, F; Vlaanderen, J; Tielemans, E; Preller, L; Bobeldijk, I; Deddens, J A; Latza, U; Baur, X; Heederik, D

2006-01-01

Objectives To study inhalation and dermal exposure to hexamethylene diisocyanate (HDI) and its oligomers as well as personal protection equipment (PPE) use during task performance in conjunction with urinary hexamethylene diamine (HDA) in car body repair shop workers and industrial spray painters. Methods Personal task based inhalation samples (n = 95) were collected from six car body repair shops and five industrial painting companies using impingers with di‐n‐butylamine (DBA) in toluene. In parallel, dermal exposure was assessed using nitril rubber gloves. Gloves were submerged into DBA in toluene after sampling. Analysis for HDI and its oligomers was performed by LC‐MS/MS. Urine samples were collected from 55 workers (n = 291) and analysed for HDA by GC‐MS. Results Inhalation exposure was strongly associated with tasks during which aerosolisation occurs. Dermal exposure occurred during tasks that involve direct handling of paint. In car body repair shops associations were found between detectable dermal exposure and glove use (odds ratio (OR) 0.22, 95% confidence interval (CI) 0.09 to 0.57) and inhalation exposure level (OR 1.34, 95% CI 0.97 to 1.84 for a 10‐fold increase). HDA in urine could be demonstrated in 36% and 10% of car body repair shop workers and industrial painting company workers respectively. In car body repair shops, the frequency of detectable HDA was significantly elevated at the end of the working day (OR 2.13, 95% CI 1.07 to 4.22 for 3–6 pm v 0–8 am). In both branches HDA was detected in urine of ∼25% of the spray painters. In addition HDA was detected in urine of a large proportion of non‐spray painters in car body repair shops. Conclusion Although (spray) painting with lacquers containing isocyanate hardeners results in the highest external exposures to HDI and oligomers, workers that do not perform paint related tasks may also receive a considerable internal dose. PMID:16728504

40 CFR 429.162 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... technology (BCT). [Reserved] 429.162 Section 429.162 Protection of Environment ENVIRONMENTAL PROTECTION... Wood Furniture and Fixture Production Without Water Wash Spray Booth(s) or Without Laundry Facilities... application of the best conventional pollutant control technology (BCT). [Reserved] ...

40 CFR 429.172 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... technology (BCT). [Reserved] 429.172 Section 429.172 Protection of Environment ENVIRONMENTAL PROTECTION... Wood Furniture and Fixture Production With Water Wash Spray Booth(s) or With Laundry Facilities... application of the best conventional pollutant control technology (BCT). [Reserved] ...

Air pollution control system research: An iterative approach to developing affordable systems

NASA Technical Reports Server (NTRS)

Watt, Lewis C.; Cannon, Fred S.; Heinsohn, Robert J.; Spaeder, Timothy A.

1995-01-01

This paper describes a Strategic Environmental Research and Development Program (SERDP) funded project led jointly by the Marine Corps Multi-Commodity Maintenance Centers, and the Air and Energy Engineering Research Laboratory (AEERL) of the USEPA. The research focuses on paint booth exhaust minimization using recirculation, and on volatile organic compound (VOC) oxidation by the modules of a hybrid air pollution control system. The research team is applying bench, pilot and full scale systems to accomplish the goals of reduced cost and improved effectiveness of air treatment systems for paint booth exhaust.

Efficacy, persistence and vector susceptibility to pirimiphos-methyl (Actellic 300CS) insecticide for indoor residual spraying in Zanzibar.

PubMed

Haji, Khamis A; Thawer, Narjis G; Khatib, Bakari O; Mcha, Juma H; Rashid, Abdallah; Ali, Abdullah S; Jones, Christopher; Bagi, Judit; Magesa, Stephen M; Ramsan, Mahdi M; Garimo, Issa; Greer, George; Reithinger, Richard; Ngondi, Jeremiah M

2015-12-09

Indoor residual spraying (IRS) of households with insecticide is a principal malaria vector control intervention in Zanzibar. In 2006, IRS using the pyrethroid lambda-cyhalothrine was introduced in Zanzibar. Following detection of pyrethroid resistance in 2010, an insecticide resistance management plan was proposed, and IRS using bendiocarb was started in 2011. In 2014, bendiocarb was replaced by pirimiphos methyl. This study investigated the residual efficacy of pirimiphos methyl (Actellic 300CS) sprayed on common surfaces of human dwellings in Zanzibar. The residual activity of Actellic 300CS was determined over 9 months through bioassay tests that measured the mortality of female Anopheles mosquitoes, exposed to sprayed surfaces under a WHO cone. The wall surfaces included; mud wall, oil or water painted walls, lime washed wall, un-plastered cement block wall and stone blocks. Insecticide susceptibility testing was done to investigate the resistance status of local malaria vectors against Actellic 300CS using WHO protocols; Anopheline species were identified using PCR methods. Baseline tests conducted one-day post-IRS revealed 100% mortality on all sprayed surfaces. The residual efficacy of Actellic 300CS was maintained on all sprayed surfaces up to 8 months post-IRS. However, the bioassay test conducted 9 months post-IRS showed the 24 h mortality rate to be ≤80% for lime wash, mud wall, water paint and stone block surfaces. Only oil paint surface retained the recommended residual efficacy beyond 9 months post-IRS, with mortality maintained at ≥97 %. Results of susceptibility tests showed that malaria vectors in Zanzibar were fully (100%) susceptible to Actellic 300CS. The predominant mosquito vector species was An. arabiensis (76.0%) in Pemba and An. gambiae (83.5%) in Unguja. The microencapsulated formulation of pirimiphos methyl (Actellic 300CS) is a highly effective and appropriate insecticide for IRS use in Zanzibar as it showed a relatively prolonged

Feasibility study of respiratory questionnaire and peak flow recordings in autobody shop workers exposed to isocyanate-containing spray paint: observations and limitations.

PubMed

Cullen, M R; Redlich, C A; Beckett, W S; Weltmann, B; Sparer, J; Jackson, G; Ruff, T; Rubinstein, E; Holden, W

1996-06-01

Diisocyanates, highly reactive monomers which cross-link polyurethane, are the most widely recognized causes of occupational asthma. Many exposed workers are end-users, including autobody spray painters who form a large population at risk. Neither the factors which determine incidence rate nor strategies for control have been adequately studied in this setting. We have conducted a cross-sectional survey of 23 (about one in five) autobody shops in the New Haven area to determine the feasibility of clinical epidemiological studies in this population. Among 102 workers, there was a high rate of airway symptoms consistent with occupational asthma (19.6%). Symptoms were most prevalent among those with the greatest opportunity for exposure (dedicated spray painters) and least among office workers; part-time painters had intermediate rates. Atopy was not associated with risk while smoking seemed to correlate with symptoms. Regular use of air-supplied respirators appeared to be associated with lower risk among workers who painted part- or full-time. We were unable to validate the questionnaire responses with peak expiratory flow record data attempted on a 1/3 sample of the workers. Despite intensive training and effort, subject compliance was limited. Among those who provided adequate data (24 of 38), only two demonstrated unequivocal evidence of labile airways; two others demonstrated lesser changes consistent with an occupational effect on flow rates. There was no clear association between these findings and either questionnaire responses or exposure classification. Overall, the survey suggests that there is a high prevalence of airway symptoms among workers in autobody shops, at least in part due to work-related asthma. However, there is need for both methodological and substantive research in this setting to document rates of occupational asthma and to develop a scientific basis for its effective control.

Paint Analysis

NASA Technical Reports Server (NTRS)

1994-01-01

Lewis Research Center (LEW) has assisted The Cleveland Museum of Art (CMA) in analyzing the museum's paintings. Because of the many layers of paint that are often involved, this is a complex process. The cross-section of a paint chip must be scanned with a microscope to determine whether a paint layer is original or a restoration. The paint samples, however, are rarely flat enough for high magnification viewing and are frequently scratched. LEW devised an automated method that produces intact, flat, polished paint cross-sections. A sophisticated microprocessor-controlled grinding and polishing machine was manually employed in preparation of exotic samples for aerospace research was a readily adaptable technique. It produced perfectly flat samples with clearly defined layers. The process has been used successfully on a number of paintings, and LEW and CMA are considering additional applications.

Emission rate modeling and risk assessment at an automobile plant from painting operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, A.; Shrivastava, A.; Kulkarni, A.

Pollution from automobile plants from painting operations has been addressed in the Clean Act Amendments (1990). The estimation of pollutant emissions from automobile painting operation were done mostly by approximate procedures than by actual calculations. The purpose of this study was to develop a methodology for calculating the emissions of the pollutants from painting operation in an automobile plant. Five scenarios involving an automobile painting operation, located in Columbus (Ohio), were studied for pollutant emission and concomitant risk associated with that. In the study of risk, a sensitivity analysis was done using Crystal Ball{reg{underscore}sign} on the parameters involved in risk.more » This software uses the Monte Carlo principle. The most sensitive factor in the risk analysis was the ground level concentration of the pollutants. All scenarios studied met the safety goal (a risk value of 1 x 10{sup {minus}6}) with different confidence levels. The highest level of confidence in meeting the safety goal was displayed by Scenario 1 (Alpha Industries). The results from the scenarios suggest that risk is associated with the quantity of released toxic pollutants. The sensitivity analysis of the various parameter shows that average spray rate of paint is the most important parameter in the estimation of pollutants from the painting operations. The entire study is a complete module that can be used by the environmental pollution control agencies for estimation of pollution levels and estimation of associated risk. The study can be further extended to other operations in an automobile industry or to different industries.« less

Demonstration and Field Test of airjacket technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faulkner, D.; Fisk, W.J.; Gadgil, A.J.

1998-06-01

There are approximately 600,000 paint spray workers in the United States applying paints and coatings with some type of sprayer. Approximately 5% of these spray workers are in the South Coast Air Quality Management District (SCAQMD). These spray workers apply paints or other coatings to products such as bridges, houses, automobiles, wood and metal furniture, and other consumer and industrial products. The materials being sprayed include exterior and interior paints, lacquers, primers, shellacs, stains and varnishes. Our experimental findings indicate that the Airjacket does not significantly reduce the exposure of spray workers to paint fumes during HVLP spraying. The differencemore » between ideal and actual spray paint procedures influence the mechanisms driving spray workers exposures to paint fumes and influence the viability of the Airjacket technology. In the ideal procedure, for which the Airjacket was conceived, the spray worker's exposure to paint fumes is due largely to the formation of a recirculating eddy between the spray worker and the object painted. The Airjacket ejects air to diminish and ventilate this eddy. In actual practice, exposures may result largely from directing paint upstream and from the bounce-back of the air/paint jet of the object being painted. The Airjacket, would not be expected to dramatically reduce exposures to paint fumes when the paint is not directed downstream or when the bounce-back of paint on the object creates a cloud of paint aerosols around the spray worker.« less

Experimental evaluation of a mathematical model for predicting transfer efficiency of a high volume-low pressure air spray gun.

PubMed

Tan, Y M; Flynn, M R

2000-10-01

The transfer efficiency of a spray-painting gun is defined as the amount of coating applied to the workpiece divided by the amount sprayed. Characterizing this transfer process allows for accurate estimation of the overspray generation rate, which is important for determining a spray painter's exposure to airborne contaminants. This study presents an experimental evaluation of a mathematical model for predicting the transfer efficiency of a high volume-low pressure spray gun. The effects of gun-to-surface distance and nozzle pressure on the agreement between the transfer efficiency measurement and prediction were examined. Wind tunnel studies and non-volatile vacuum pump oil in place of commercial paint were used to determine transfer efficiency at nine gun-to-surface distances and four nozzle pressure levels. The mathematical model successfully predicts transfer efficiency within the uncertainty limits. The least squares regression between measured and predicted transfer efficiency has a slope of 0.83 and an intercept of 0.12 (R2 = 0.98). Two correction factors were determined to improve the mathematical model. At higher nozzle pressure settings, 6.5 psig and 5.5 psig, the correction factor is a function of both gun-to-surface distance and nozzle pressure level. At lower nozzle pressures, 4 psig and 2.75 psig, gun-to-surface distance slightly influences the correction factor, while nozzle pressure has no discernible effect.

Hexavalent chromium and isocyanate exposures during military aircraft painting under crossflow ventilation.

PubMed

Bennett, James S; Marlow, David A; Nourian, Fariba; Breay, James; Hammond, Duane

2016-01-01

Exposure control systems performance was investigated in an aircraft painting hangar. The ability of the ventilation system and respiratory protection program to limit worker exposures was examined through air sampling during painting of F/A-18C/D strike fighter aircraft, in four field surveys. Air velocities were measured across the supply filter, exhaust filter, and hangar midplane under crossflow ventilation. Air sampling conducted during painting process phases (wipe-down, primer spraying, and topcoat spraying) encompassed volatile organic compounds, total particulate matter, Cr[VI], metals, nitroethane, and hexamethylene diisocyanate, for two worker groups: sprayers and sprayer helpers ("hosemen"). One of six methyl ethyl ketone and two of six methyl isobutyl ketone samples exceeded the short term exposure limits of 300 and 75 ppm, with means 57 ppm and 63 ppm, respectively. All 12 Cr[VI] 8-hr time-weighted averages exceeded the recommended exposure limit of 1 µg/m3, 11 out of 12 exceeded the permissible exposure limit of 5 µg/m3, and 7 out of 12 exceeded the threshold limit value of 10 µg/m3, with means 38 µg/m3 for sprayers and 8.3 µg/m3 for hosemen. Hexamethylene diisocyanate means were 5.95 µg/m3 for sprayers and 0.645 µg/m3 for hosemen. Total reactive isocyanate group--the total of monomer and oligomer as NCO group mass--showed 6 of 15 personal samples exceeded the United Kingdom Health and Safety Executive workplace exposure limit of 20 µg/m3, with means 50.9 µg/m3 for sprayers and 7.29 µg/m3 for hosemen. Several exposure limits were exceeded, reinforcing continued use of personal protective equipment. The supply rate, 94.4 m3/s (200,000 cfm), produced a velocity of 8.58 m/s (157 fpm) at the supply filter, while the exhaust rate, 68.7 m3/s (146,000 cfm), drew 1.34 m/s (264 fpm) at the exhaust filter. Midway between supply and exhaust locations, the velocity was 0.528 m/s (104 fpm). Supply rate exceeding exhaust rate created re

Reducer Selection When Doing Overall Paint Jobs Using Enamel Paints. Lesson Plan No. 1 of Auto Repair and Painting.

ERIC Educational Resources Information Center

Tyau, Layton M.

This lesson, which is part of a high school course in auto body repair and painting, deals with selecting a reducer when doing overall paint jobs using enamel paints. Students are taught the general properties of different types of enamel paints and selection of the proper reducer for each type of paint, depending on the weather and the specific…

Pipeline active filter utilizing a booth type multiplier

NASA Technical Reports Server (NTRS)

Nathan, Robert (Inventor)

1987-01-01

Multiplier units of the modified Booth decoder and carry-save adder/full adder combination are used to implement a pipeline active filter wherein pixel data is processed sequentially, and each pixel need only be accessed once and multiplied by a predetermined number of weights simultaneously, one multiplier unit for each weight. Each multiplier unit uses only one row of carry-save adders, and the results are shifted to less significant multiplier positions and one row of full adders to add the carry to the sum in order to provide the correct binary number for the product Wp. The full adder is also used to add this product Wp to the sum of products .SIGMA.Wp from preceding multiply units. If m.times.m multiplier units are pipelined, the system would be capable of processing a kernel array of m.times.m weighting factors.

49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 2 2011-10-01 2011-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 2 2013-10-01 2013-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 2 2012-10-01 2012-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 2 2014-10-01 2014-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

29 CFR 1926.57 - Ventilation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... into a duct or hood. It is usually expressed in inches of water gauge. (vii) Exhaust system. A system... velocity. It is usually expressed in inches of water gauge. (xviii) Vertical spindle disc grinder. A... operate the booth without the filters in place. (iv) (A) For wet or water-wash spray booths, the water...

29 CFR 1926.57 - Ventilation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... into a duct or hood. It is usually expressed in inches of water gauge. (vii) Exhaust system. A system... velocity. It is usually expressed in inches of water gauge. (xviii) Vertical spindle disc grinder. A... operate the booth without the filters in place. (iv) (A) For wet or water-wash spray booths, the water...

Hexavalent Chromium and Isocyanate Exposures during Military Aircraft Painting under Crossflow Ventilation

PubMed Central

Bennett, James S.; Marlow, David A.; Nourian, Fariba; Breay, James; Hammond, Duane

2016-01-01

Exposure control systems performance was investigated in an aircraft painting hangar. The ability of the ventilation system and respiratory protection program to limit worker exposures was examined through air sampling during painting of F/A-18C/D strike fighter aircraft, in four field surveys. Air velocities were measured across the supply filter, exhaust filter, and hangar midplane under crossflow ventilation. Air sampling conducted during painting process phases (wipe-down, primer spraying, and topcoat spraying) encompassed volatile organic compounds, total particulate matter, Cr[VI], metals, nitroethane, and hexamethylene diisocyanate, for two worker groups: sprayers and sprayer helpers (“hosemen”). One of six methyl ethyl ketone and two of six methyl isobutyl ketone samples exceeded the short term exposure limits of 300 and 75 ppm, with means 57 ppm and 63 ppm, respectively. All 12 Cr[VI] 8-hr time-weighted averages exceeded the recommended exposure limit of 1 µg/m3, 11 out of 12 exceeded the permissible exposure limit of 5 µg/m3, and 7 out of 12 exceeded the threshold limit value of 10 µg/m3, with means 38 µg/m3 for sprayers and 8.3 µg/m3 for hosemen. Hexamethylene diisocyanate means were 5.95 µg/m3 for sprayers and 0.645 µg/m3 for hosemen. Total reactive isocyanate group—the total of monomer and oligomer as NCO group mass—showed six of 15 personal samples exceeded the United Kingdom Health and Safety Executive workplace exposure limit of 20 µg/m3, with means 50.9 µg/m3 for sprayers and 7.29 µg/m3 for hosemen. Several exposure limits were exceeded, reinforcing continued use of personal protective equipment. The supply rate, 94.4 m3/s (200,000 cfm), produced a velocity of 8.58 m/s (157 fpm) at the supply filter, while the exhaust rate, 68.7 m3/s (146,000 cfm), drew 1.34 m/s (264 fpm) at the exhaust filter. Midway between supply and exhaust locations, the velocity was 0.528 m/s (104 fpm). Supply rate exceeding exhaust rate created re

EVALUATION OF STYRENE EMISSIONS FROM A SHOWER STALL/BATHTUB MANUFACTURING FACILITY

EPA Science Inventory

The report gives results of emissions measurements carried out at a representative facility (Eljer Plumbingware in Wilson, NC) that manufactures polyester-resin-reinforced shower stalls and bathtubs by spraying styrene-based resins onto molds in vented, open, spray booths. Styren...

Hundreds of Area Residents Visit the National Lab Booth at the Annual In The Street Festival | Poster

Cancer.gov

Light-up yo-yos, brightly colored portion plates, and a fast spinner game lured hundreds of area residents to the Frederick National Lab booth at this year’s In The Street festival, where they also heard a message from the lab: Stay healthy through healthy habits.

F-111 Adhesively Bonded Repair Assessment Program (FABRAP) - Phase 1 Testing, Preliminary Results

DTIC Science & Technology

2011-08-01

additional hazards when used outside of a fume cupboard/booth. Citrasafe is a non-toxic low volatile plant extract solvent which has been shown to be...on RAAF aircraft. Removal of paint could potentially expose personnel to hexavalent chromium , which is highly toxic. There are two acceptable methods...hexavalent chromium , which is highly toxic. There are two acceptable methods of removing aircraft paint – by sanding, or using paint strippers

Technology Insertion for Recapitalization of Legacy Systems

DTIC Science & Technology

2015-09-30

peened, and 4) an Abcite coating will be flame sprayed on the component. The ALCM program (B) has 1) evaluated data provided, 2) gathered questions...Report Technology Insertion for the Recapitalization of Legacy Systems Laser sintering, thermal spray and cold spray are additive manufacturing methods... coatings Need an experienced operator Requires a special spray booth to limit overspray and protect operator Requires primer or surface treatment

Egyptian Tomb Painting.

ERIC Educational Resources Information Center

Schroeder, Liesa

1999-01-01

Provides an activity where sixth-grade students replicated the Egyptian art form of tomb painting. Explains that the students researched information about Egyptian culture and history in order to familiarize themselves with Egyptian wall-painting style. Discusses the process of creating tomb paintings in detail. (CMK)

Monet's Painting under the Microscope

NASA Astrophysics Data System (ADS)

Dredge, Paula; Wuhrer, Richard; Phillips, Matthew R.

2003-04-01

An oil painting by Claude Monet, Port-Goulphar, Belle-Ile 1887 (collection of the Art Gallery of New South Wales), was examined to determine both the identity of the pigments used by the artist in this painting and his technique of mixing colors and laying paint on the canvas. The extremely complex construction of the painting was revealed by optical microscopy, scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDS), and X-ray mapping (XRM) analysis of cross sections of paint flakes excised from damaged regions of Port-Goulphar, Belle-Ile. Nine different pigments were found on the painting. Many of the identified colors were modern pigments that became available only late in the 19th century as a result of scientific advances in pigment chemistry. Although similar colors were available in a natural mineral form, they lacked the vivid color of their manufactured counterparts. The use of these new synthetic metallic oxide colors by Monet accounts for the brilliance of his paintings. In addition, a separation between successive paint layers was observed in some areas of paint chip cross sections, indicating that oil-based paint was applied to paint that had dried, and consequently, Port-Goulphar, Belle-Ile was painted over a long period of time. This observation is contrary to the general perception of Monet's technique of painting freely and quickly.

Monet's painting under the microscope.

PubMed

Dredge, Paula; Wuhrer, Richard; Phillips, Matthew R

2003-04-01

An oil painting by Claude Monet, Port-Goulphar, Belle-Ile 1887 (collection of the Art Gallery of New South Wales), was examined to determine both the identity of the pigments used by the artist in this painting and his technique of mixing colors and laying paint on the canvas. The extremely complex construction of the painting was revealed by optical microscopy, scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDS), and X-ray mapping (XRM) analysis of cross sections of paint flakes excised from damaged regions of Port-Goulphar, Belle-Ile. Nine different pigments were found on the painting. Many of the identified colors were modern pigments that became available only late in the 19th century as a result of scientific advances in pigment chemistry. Although similar colors were available in a natural mineral form, they lacked the vivid color of their manufactured counterparts. The use of these new synthetic metallic oxide colors by Monet accounts for the brilliance of his paintings. In addition, a separation between successive paint layers was observed in some areas of paint chip cross sections, indicating that oil-based paint was applied to paint that had dried, and consequently, Port-Goulphar, Belle-Ile was painted over a long period of time. This observation is contrary to the general perception of Monet's technique of painting freely and quickly.

Producing intricate IPMC shapes by means of spray-painting and printing (Conference Presentation)

NASA Astrophysics Data System (ADS)

Trabia, Sarah; Olsen, Zakai; Hwang, Taeseon; Kim, Kwang Jin

2017-04-01

Ionic Polymer-Metal Composites (IPMC) are common soft actuators that are Nafion® based and plated with a conductive metal, such as platinum, gold, or palladium. Nafion® is available in three forms: sheets, pellets, and water dispersion. Nafion® sheets can be cut to the desired dimensions and are best for rectangular IPMCs. However, the user is not able to change the thickness of these sheets by stacking and melting because Nafion® does not melt. A solution to this is Nafion® pellets, which can melt. These can be used for extrusion and injection molding. Though Nafion® pellets can be melted, they are difficult to work with, making the process quite challenging to master. The last form is Nafion® Water Dispersion, which can be used for casting. Casting can produce the desired thickness, but it does not solve the problem of achieving complex contours. The current methods of fabrication do not allow for complex shapes and structures. To solve this problem, two methods are presented: painting and printing. The painting method uses Nafion® Water Dispersion, an airbrush, and vinyl stencils. The stencils can be made into any shape with detailed edges. The printing method uses Nafion® pellets that are extruded into filaments and a commercially available 3D printer. The models are drawn in a Computer-Aided Drawing (CAD) program, such as SolidWorks. The produced Nafion® membranes will be compared with a commercial Nafion® membrane through a variety of tests, including Fourier Transform Infrared Spectroscopy, Scanning Electron Microscope, Thermogravimetric Analysis, Dynamic Mechanical Analysis, and Optical Microscope.

Waste Minimization Program. Air Force Plant 4.

DTIC Science & Technology

1986-02-01

incinerator equipped with a secondary combustion chamber and venturi scrubber could serve AFP 4’s needs. As the wastes listed in Table 3-6 contain negligible... scrubber water treatment in the AFP 4eatment. waste treatment system. 2.3 ECONOMICS -Table 2-3 summarizes the projected economics of the recommendations for...control devices. These paint booths are equipped with water curtain air scrubbers which remove solids from the booth exhaust by providing - intimate

The Professor as Teacher: Allan Bloom, Wayne Booth, and the Tradition of Teaching at the University of Chicago.

ERIC Educational Resources Information Center

Wrightson, Katherine M.

1998-01-01

The University of Chicago (Illinois) has long emphasized teaching as a valued skill, fostering an image focused on the intellectual search for truth and transmission of intellectual values, a stand in opposition to popular relativist theories. Through the writings of Allan Bloom, Wayne Booth, and historical university documents, this model of…

International forensic automotive paint database

NASA Astrophysics Data System (ADS)

Bishea, Gregory A.; Buckle, Joe L.; Ryland, Scott G.

1999-02-01

The Technical Working Group for Materials Analysis (TWGMAT) is supporting an international forensic automotive paint database. The Federal Bureau of Investigation and the Royal Canadian Mounted Police (RCMP) are collaborating on this effort through TWGMAT. This paper outlines the support and further development of the RCMP's Automotive Paint Database, `Paint Data Query'. This cooperative agreement augments and supports a current, validated, searchable, automotive paint database that is used to identify make(s), model(s), and year(s) of questioned paint samples in hit-and-run fatalities and other associated investigations involving automotive paint.

Method Development for Binding Media Analysis in Painting Cross-Sections by Desorption Electrospray Ionization-Mass Spectrometry (DESI-MS).

PubMed

Watts, Kristen; Lagalante, Anthony

2018-06-06

Art conservation science is in need of a relatively nondestructive way of rapidly identifying the binding media within a painting cross-section and isolating binding media to specific layers within the cross-section. Knowledge of the stratigraphy of cross-sections can be helpful for removing possible unoriginal paint layers on the artistic work. Desorption electrospray ionization-mass spectrometry (DESI-MS) was used in ambient mode to study cross-sections from mock-up layered paint samples and samples from a 17th century baroque painting. The DESI spray was raster scanned perpendicular to the cross-section layers to maximize lateral resolution then analyzed with a triple quadrupole mass analyzer in linear ion trap mode. From these scans, isobaric mass maps were created to map the locations of masses indicative of particular binding media onto the cross-sections. Line paint-outs of pigments in different binding media showed specific and unique ions to distinguish between the modern acrylic media and the lipid containing binding media. This included: OP (EO) 9 surfactant in positive ESI for acrylic (m/z 621), and oleic (m/z 281), stearic (m/z 283), and azelaic (m/z 187) acids in negative ESI for oil and egg tempera. DESI-MS maps of mock-up cross-sections of layered pigmented binding media showed correlation between these ions and the layers with a spatial resolution of 100 μm. DESI-MS is effective in monitoring binding media within an intact painting cross-section via mass spectrometric methods. This includes distinguishing between lipid-containing and modern binding materials present in a known mockup cross section matrix as well as identifying lipid binding media in a 17th century baroque era painting. This article is protected by copyright. All rights reserved.

Painted Pickup.

ERIC Educational Resources Information Center

Wheeler, Kimberly

2001-01-01

Discusses a six week art class project for elementary school children that lasted for six weeks. Explains that the students painted sunflowers in the style of Vincent van Gogh over the rust spots of a pickup truck. Reports that the painting served as great publicity for the art classes. (CMK)

Assessment of DNA damage in car spray painters exposed to organic solvents by the high-throughput comet assay.

PubMed

Londoño-Velasco, Elizabeth; Martínez-Perafán, Fabián; Carvajal-Varona, Silvio; García-Vallejo, Felipe; Hoyos-Giraldo, Luz Stella

2016-05-01

Occupational exposure as a painter is associated with DNA damage and development of cancer. Comet assay has been widely adopted as a sensitive and quantitative tool for DNA damage assessment at the individual cell level in populations exposed to genotoxics. The aim of this study was to assess the application of the high-throughput comet assay, to determine the DNA damage in car spray painters. The study population included 52 car spray painters and 52 unexposed subjects. A significant increase in the %TDNA median (p <  0.001) was observed in the exposed group in comparison to the unexposed group. Neither age (%TDNA: p =  0.913) nor time of exposure (%TDNA: p = 0.398) were significantly correlated with DNA damage. The car spray painters who consumed alcohol did not show a significant increase in DNA damage compared to nonalcohol consumers (p  > 0.05). The results showed an increase in DNA breaks in car spray painters exposed to organic solvents and paints; furthermore, they demonstrated the application of high-throughput comet assay in an occupational exposure study to genotoxic agents.

1. Photocopy of painting (original painting in possesion of the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Photocopy of painting (original painting in possesion of the family of Judge Jasper Brinton, Cairo, Egypt) Thomas Eakins, Artist 1878 SIDE AND FRONT ELEVATIONS - Brinton 1704 House, Oakland Road (Birmingham Township), Dilworthtown, Chester County, PA

Texton-based analysis of paintings

NASA Astrophysics Data System (ADS)

van der Maaten, Laurens J. P.; Postma, Eric O.

2010-08-01

The visual examination of paintings is traditionally performed by skilled art historians using their eyes. Recent advances in intelligent systems may support art historians in determining the authenticity or date of creation of paintings. In this paper, we propose a technique for the examination of brushstroke structure that views the wildly overlapping brushstrokes as texture. The analysis of the painting texture is performed with the help of a texton codebook, i.e., a codebook of small prototypical textural patches. The texton codebook can be learned from a collection of paintings. Our textural analysis technique represents paintings in terms of histograms that measure the frequency by which the textons in the codebook occur in the painting (so-called texton histograms). We present experiments that show the validity and effectiveness of our technique for textural analysis on a collection of digitized high-resolution reproductions of paintings by Van Gogh and his contemporaries. As texton histograms cannot be easily be interpreted by art experts, the paper proposes to approaches to visualize the results on the textural analysis. The first approach visualizes the similarities between the histogram representations of paintings by employing a recently proposed dimensionality reduction technique, called t-SNE. We show that t-SNE reveals a clear separation of paintings created by Van Gogh and those created by other painters. In addition, the period of creation is faithfully reflected in the t-SNE visualizations. The second approach visualizes the similarities and differences between paintings by highlighting regions in a painting in which the textural structure of the painting is unusual. We illustrate the validity of this approach by means of an experiment in which we highlight regions in a painting by Monet that are not very "Van Gogh-like". Taken together, we believe the tools developed in this study are well capable of assisting for art historians in support of

Air formaldehyde and solvent concentrations during surface coating with acid-curing lacquers and paints in the woodworking and furniture industry.

PubMed

Thorud, Syvert; Gjolstad, Merete; Ellingsen, Dag G; Molander, Paal

2005-06-01

An investigation of contemporary exposure to formaldehyde and organic solvents has been carried out during surface coating with acid-curing lacquers and paints in the Norwegian woodworking and furniture industry over a period of 3 years. The investigation covered 27 factories of different sizes and with different types of production, and totally 557 parallel formaldehyde and solvent samples were collected. The formaldehyde concentration (geometric mean) was 0.15 ppm (range 0.01-1.48 ppm) with about 10% of the samples exceeding the Norwegian occupational exposure limit of 0.5 ppm. The solvent concentration as additive effect (geometric mean) was 0.13 (range 0.0004-5.08) and about 5% of the samples exceeded the Norwegian occupational exposure limit. The most frequently occurring solvents from acid-curing lacquers were n-butyl acetate, ethanol, ethyl acetate and 1-butanol, which were found in 88-98% of the samples. Toluene, n-butyl acetate and 1-butanol were the only solvents with maximum concentrations exceeding their respective occupational exposure limits. Curtain painting machine operators were exposed to the highest concentrations of both formaldehyde (geometric mean 0.51 ppm, range 0.08-1.48 ppm) and organic solvents (additive effect, geometric mean 1.18, range 0.02-5.08). Other painting application work tasks such as automatic and manual spray-painting, manual painting and dip painting, showed on average considerably lower concentrations of both formaldehyde (geometric means 0.07-0.16 ppm) and organic solvents (additive effect, geometric mean 0.02-0.18). Non-painting work tasks also displayed moderate concentrations of formaldehyde (geometric means 0.11-0.17 ppm) and organic solvents (additive effect, geometric mean 0.04-0.07).

9. Photocopy of painting (Painted by the architect, Mr. Lee ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. Photocopy of painting (Painted by the architect, Mr. Lee and presented to the Rev. J.J. Roberts, Rector, 1853-1866) April 1960 EXTERIOR, GENERAL VIEW - Church of the Holy Cross, State Route 261, Stateburg, Sumter County, SC

Monster Paintings

ERIC Educational Resources Information Center

Huggler, Silvia

2010-01-01

In this article, the author describes a unit on monsters wherein students were charged with painting an imaginary character and, in so doing, demonstrated mastery of expression, organization of space, control of paint media, and application of the elements of art. Students discovered how color and line could be used to convey expression. The media…

40 CFR 52.2320 - Identification of plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... dated February 5, 1985, HAFB AO for Paint Booth, HVAC Modification, Standby Generators, and Fuel Storage... implementation of the inspection of vehicle On-Board Diagnostic (OBD) systems starting January 1, 2002 in all...

40 CFR 52.2320 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... dated February 5, 1985, HAFB AO for Paint Booth, HVAC Modification, Standby Generators, and Fuel Storage... implementation of the inspection of vehicle On-Board Diagnostic (OBD) systems starting January 1, 2002 in all...

40 CFR 52.2320 - Identification of plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... dated February 5, 1985, HAFB AO for Paint Booth, HVAC Modification, Standby Generators, and Fuel Storage... implementation of the inspection of vehicle On-Board Diagnostic (OBD) systems starting January 1, 2002 in all...

BORED AND ASSEMBLED GATE VALVES RECEIVING PROTECTIVE COATING IN THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

BORED AND ASSEMBLED GATE VALVES RECEIVING PROTECTIVE COATING IN THE VALVE PAINT BOOTH OF THE VALVE ASSEMBLY BUILDING. - Stockham Pipe & Fittings Company, Valve Assembly Building, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

Pressure Sensitive Paints

NASA Technical Reports Server (NTRS)

Liu, Tianshu; Bencic, T.; Sullivan, J. P.

1999-01-01

This article reviews new advances and applications of pressure sensitive paints in aerodynamic testing. Emphasis is placed on important technical aspects of pressure sensitive paint including instrumentation, data processing, and uncertainty analysis.

Noncircular Cross Sections Could Enhance Mixing in Sprays

NASA Technical Reports Server (NTRS)

Bellan, Josette; Abdel-Hameed, Hesham

2003-01-01

A computational study has shown that by injecting drops in jets of gas having square, elliptical, triangular, or other noncircular injection cross sections, it should be possible to increase (relative to comparable situations having circular cross section) the entrainment and dispersion of liquid drops. This finding has practical significance for a variety of applications in which it is desirable to increase dispersion of drops. For example, in chemical-process sprays, increased dispersion leads to increases in chemical- reaction rates; in diesel engines, increasing the dispersion of drops of sprayed fuel reduces the production of soot; and in household and paint sprays, increasing the dispersion of drops makes it possible to cover larger surfaces. It has been known for some years that single-phase fluid jets that enter flow fields through noncircular inlets entrain more fluid than do comparable jets entering through circular inlets. The computational study reported here was directed in part toward determining whether and how this superior mixing characteristic of noncircular single phase jets translates to a similar benefit in cases of two-phase jets (that is, sprays). The study involved direct numerical simulations of single- and two-phase free jets with circular, elliptical, rectangular, square, and triangular inlet cross sections. The two-phase jets consisted of gas laden with liquid drops randomly injected at the inlets. To address the more interesting case of evaporating drops, the carrier gas in the jets was specified to be initially unvitiated by the vapor of the liquid chemical species and the initial temperature of the drops was chosen to be smaller than that of the gas. The mathematical model used in the study was constructed from the conservation equations for the two-phase flow and included complete couplings of mass, momentum, and energy based on thermodynamically self-consistent specification of the enthalpy, internal energy, and latent heat of

An indoor air quality evaluation in a residential retrofit project using spray polyurethane foam.

PubMed

Tian, Shen; Ecoff, Scott; Sebroski, John; Miller, Jason; Rickenbacker, Harold; Bilec, Melissa

2018-05-01

Understanding of indoor air quality (IAQ) during and after spray polyurethane foam (SPF) application is essential to protect the health of both workers and building occupants. Previous efforts such as field monitoring, micro-chamber/spray booth emission studies, and fate/transport modeling have been conducted to understand the chemical exposure of SPF and guide risk mitigation strategies. However, each type of research has its limitation and can only reveal partial information on the relationship between SPF and IAQ. A comprehensive study is truly needed to integrate the experimental design and analytical testing methods in the field/chamber studies with the mathematical tools employed in the modeling studies. This study aims to bridge this gap and provide a more comprehensive understanding on the impact of SPF to IAQ. The field sampling plan of this research aims to evaluate the airborne concentrations of methylene diphenyl diisocyanate (MDI), formaldehyde, acetaldehyde, propionaldehyde, tris(1-chlor-2-propyl)phosphate (TCPP), trans-1-chloro-3,3,3-trifluoropropene (Solstice TM ), and airborne particles. Modifications to existing MDI sampling and analytical methods were made so that level of quantification was improved. In addition, key fate and transport modeling input parameters such as air changes per hour and airborne particle size distribution were measured. More importantly, TCPP accumulation onto materials was evaluated, which is important to study the fate and transport of semi-volatile organic compounds. The IAQ results showed that after spray application was completed in the entire building, airborne concentrations decreased for all chemicals monitored. However, it is our recommendation that during SPF application, no one should return to the application site without proper personal protection equipment as long as there are active spray activities in the building. The comparison between this field study and a recent chamber study proved surface sorption

Additive Transforms Paint into Insulation

NASA Technical Reports Server (NTRS)

2007-01-01

Tech Traders Inc. sought assistance developing low-cost, highly effective coatings and paints that created useful thermal reflectance and were safe and non-toxic. In cooperation with a group of engineers at Kennedy Space Center., Tech Traders created Insuladd, a powder additive made up of microscopic, inert gas-filled, ceramic microspheres that can be mixed into ordinary interior or exterior paint, allowing the paint to act like a layer of insulation. When the paint dries, this forms a radiant heat barrier, turning the ordinary house paint into heat-reflecting thermal paint. According to Tech Traders, the product works with all types of paints and coatings and will not change the coverage rate, application, or adhesion of the paint. Other useful applications include feed storage silos to help prevent feed spoilage, poultry hatcheries to reduce the summer heat and winter cold effects, and on military vehicles and ships. Tech Traders has continued its connection to the aerospace community by recently providing Lockheed Martin Corporation with one of its thermal products for use on the F-22 Raptor.

The effect of BaM/PANI composition with epoxy paint matrix on single and double layers coating with spray coating method for radar absorbing materials applications

NASA Astrophysics Data System (ADS)

Widyastuti, Fajarin, Rindang; Pratiwi, Vania Mitha; Kholid, Rifki Rachman; Habib, Abdulloh

2018-04-01

In this study, RAM composite has been succesfully synthesized by mixing BaM as magnetic materials and PANI as conductive materials. BaM and PANI materials were prepared separately by solid state method and polymerization method, respectively. To investigated the presence of BaM phase and magnetic property of the as prepared BaM, XRD pert PAN analytical and VSM 250 Dexing Magnet were employed. Inductance Capacitance Resistance technique was carried out to measure electrical conductivity of the synthesized PANI materials. In order to further characterized the structural features of BaM and PANI, SEM-EDX FEI 850 and FTIR characterizations were conducted. RAM composite was prepared by mixing BaM and PANI powders with ultrasonic cleaner. Afterwards, VNA (Vector Network Analyzer) characterization was carried out to determine reflection loss value of RAM by applying mixed RAM composite and epoxy paint on aluminum plate using spray gun. Microscopic characterization was employed to investigated the distribution of RAM particles on the substrate. It was found that reflection loss value as low as -27.153 dB was achieved when applied 15 wt% BaM/PANi composite at 100.6 µm thickness. In addition, the absorption of electromagnetic waves value increase as the addition of RAM composite composition increases.

Evaluation of Innovative Volatile Organic Compound and Hazardous Air Pollutant Control Technologies for U.S. Air Force Paint Spray Booths

DTIC Science & Technology

1990-10-01

adsorption/incineration * Membrane vapor separation/condensation * Supercritical fluid oxidation • UV/ozone destruction * Molten salt combustion process...separation/ separate air stream contaminants 9 Oxygenated solvents condensation * Chlorinated hydrocarbons Supercritical fluid * Technology utilizing high...testing or full-scale unit capacity; they are: * Supercritical fluid oxidation • UV/ozone destruction * Molten salt incineration * Infrared incineration

Spray Foam Exterior Insulation with Stand-Off Furring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herk, Anastasia; Baker, Richard; Prahl, Duncan

IBACOS, in collaboration with GreenHomes America, was contracted by the New York State Energy Research and Development Authority to research exterior wall insulation solutions. This research investigated cost-effective deep energy retrofit (DER) solutions for improving the building shell exterior while achieving a cost-reduction goal, including reduced labor costs to reach a 50/50 split between material and labor. The strategies included exterior wall insulation plus energy upgrades as needed in the attic, mechanical and ventilation systems, and basement band joist, walls, and floors. The work can be integrated with other home improvements such as siding or window replacement. This strategy minimizesmore » physical connections to existing wall studs, encapsulates existing siding materials (including lead paint) with spray foam, and creates a vented rain screen assembly to promote drying. GreenHomes America applied construction details created by IBACOS to a test home. 2x4 framing members were attached to the wall at band joists and top plates using 'L' clips, with spray foam insulating the wall after framing was installed. Windows were installed simultaneously with the framing, including extension jambs. The use of clips in specific areas provided the best strength potential, and 'picture framing' the spray foam held the 2x4s in place. Short-term testing was performed at this house, with monitoring equipment installed for long-term testing. Testing measurements will be provided in a later report, as well as utility impact (before and after), costs (labor and materials), construction time, standard specifications, and analysis for the exterior wall insulation strategy.« less

Spray Foam Exterior Insulation with Stand-Off Furring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herk, Anatasia; Baker, Richard; Prahl, Duncan

IBACOS, in collaboration with GreenHomes America, was contracted by the New York State Energy Research and Development Authority to research exterior wall insulation solutions. This research investigated cost-effective deep energy retrofit (DER) solutions for improving the building shell exterior while achieving a cost-reduction goal, including reduced labor costs to reach a 50/50 split between material and labor. The strategies included exterior wall insulation plus energy upgrades as needed in the attic, mechanical and ventilation systems, and basement band joist, walls, and floors. The work can be integrated with other home improvements such as siding or window replacement. This strategy minimizesmore » physical connections to existing wall studs, encapsulates existing siding materials (including lead paint) with spray foam, and creates a vented rain screen assembly to promote drying. GreenHomes America applied construction details created by IBACOS to a test home. 2x4 framing members were attached to the wall at band joists and top plates using "L" clips, with spray foam insulating the wall after framing was installed. Windows were installed simultaneously with the framing, including extension jambs. The use of clips in specific areas provided the best strength potential, and "picture framing" the spray foam held the 2x4s in place. Short-term testing was performed at this house, with monitoring equipment installed for long-term testing. Testing measurements will be provided in a later report, as well as utility impact (before and after), costs (labor and materials), construction time, standard specifications, and analysis for the exterior wall insulation strategy.« less

RIGGERS LOFT/PAINT SHOP/SHEET METAL SHOP, VIEW TO SOUTHEAST. THE PAINT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

RIGGERS LOFT/PAINT SHOP/SHEET METAL SHOP, VIEW TO SOUTHEAST. THE PAINT SHOP WAS LOCATED IN THE CLOSEST CORNER OF THE BUILDING. THE SHEET METAL SHOP WAS LOCATED IN THE CORNER OF THE BUILDING ON THE RIGHT. THE RIGGERS LOFT WAS LOCATED IN THE PORTION OF THE BUILDING OUT OF VIEW TO THE LEFT - Rosie the Riveter National Historical Park, Riggers Loft/Paint Shop/Sheet Metal Shop, 1322 Canal Boulevard, Richmond, Contra Costa County, CA

40 CFR 60.541 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... facility (parts per million by volume) Dc=density of cement or spray material (grams per liter (lb per... which the tire is mounted. Bead cementing operation means the system that is used to apply cement to the... consists of a cement application station, such as a dip tank, spray booth and nozzles, cement trough and...

Selectively strippable paint schemes

NASA Astrophysics Data System (ADS)

Stein, R.; Thumm, D.; Blackford, Roger W.

1993-03-01

In order to meet the requirements of more environmentally acceptable paint stripping processes many different removal methods are under evaluation. These new processes can be divided into mechanical and chemical methods. ICI has developed a paint scheme with intermediate coat and fluid resistant polyurethane topcoat which can be stripped chemically in a short period of time with methylene chloride free and phenol free paint strippers.

Ignition of Liquid Fuel Spray and Simulated Solid Rocket Fuel by Photoignition of Carbon Nanotube Utilizing a Camera Flash

DTIC Science & Technology

2011-12-01

10,11 There has been a recent report on the photoignition of graphene oxide for fuel ignition applications.12 In this report, we will describe the...slide Aluminum foil Glass petri dish Xe flash Camera Sample Black spray paint Figure 2- Schematic and photographs of the experimental setup...Gilje, Sergey Dubin, Alireza Badakhshan, Jabari Farrar, Stephen. A. Danczyk, Richard B. Kaner, “Photothermal Deoxygenation of Graphene Oxide for

Reading Through Paint

NASA Technical Reports Server (NTRS)

2004-01-01

Two-dimensional data matrix symbols, which contain encoded letters and numbers, are permanently etched on items for identification. They can store up to 100 times more information than traditional bar codes. While the symbols provide several advantages over bar codes, once they are covered by paint they can no longer be read by optical scanners. Since most products are painted eventually, this presents a problem for industries relying on the symbols for identification and tracking. In 1987, NASA s Marshall Space Flight Center began studying direct parts marking with matrix symbols in order to track millions of Space Shuttle parts. Advances in the technology proved that by incorporating magnetic properties into the paints, inks, and pastes used to apply the matrix symbols, the codes could be read by a magnetic scanner even after being covered with paint or other coatings. NASA received a patent for such a scanner in 1998, but the system it used for development was not portable and was too costly. A prototype was needed as a lead-in to a production model. In the summer of 2000, NASA began seeking companies to build a hand-held scanner that would detect the Read Through Paint data matrix identification marks containing magnetic materials through coatings.

Heterogeneous Reactivity of NO2 with Photocatalytic Paints: A Possible Source of Nitrous Acid (HONO) in the Indoor Environment

NASA Astrophysics Data System (ADS)

Gligorovski, S.; Bartolomei, V.; Gandolfo, A.; Gomez Alvarez, E.; Kleffmann, J.; Wortham, H.

2014-12-01

There is an increasing concern about the indoor air environment, where we spend most of our time. Common methods of improving indoor air quality include controlling pollution sources, increasing ventilation rates or using air purifiers. Photocatalytic remediation technology was suggested as a new possibility to eliminate indoor air pollutants instead of just diluting or disposing them. In the present study, heterogeneous reactions of NO2 were studied on photocatalytic paints containing different size and quantity of TiO2. The heterogeneous reactions were conducted in a photo reactor under simulated atmospheric conditions. The flat pyrex rectangular plates covered with the paint were inserted into the reactor. These plates have been sprayed with the photocatalytic paints at our industrial partner's (ALLIOS) facilities using a high precision procedure that allowed the application of a thin layer of a given thickness of the paint. This allows a homogeneous coverage of the surface with the paint and an accurate determination of the exact amount of paint exposed to gaseous NO2. We demonstrate that the indoor photocatalytic paints which contain TiO2 can substantially reduce the concentrations of nitrogen dioxide (NO2). We show that the efficiency of nitrogen dioxide (NO2) removal increase with the quantity of TiO2 in the range 0 - 7 %. The geometric uptake coefficients increase from 5 · 10-6 to 1.6 · 10-5 under light irradiation of the paints. On the other hand, during the reactions of NO2 with this paint (7 % of TiO2) nitric oxide (NO) and nitrous acid (HONO) are formed. Nitrous acid (HONO) is an important harmful indoor pollutant and its photolysis leads to the formation of highly reactive OH radicals (Gomez Alvarez et al., 2013). Maximum conversion efficiencies of NO2to HONO and NO of 15 % and 33 % were observed at 30 % RH, respectively. Thus, the quantity of TiO2 embedded in the paint is an important parameter regarding the nitrogen oxides (NOx = NO + NO2

Order-fractal transitions in abstract paintings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calleja, E.M. de la, E-mail: elsama79@gmail.com; Cervantes, F.; Calleja, J. de la

2016-08-15

In this study, we determined the degree of order for 22 Jackson Pollock paintings using the Hausdorff–Besicovitch fractal dimension. Based on the maximum value of each multi-fractal spectrum, the artworks were classified according to the year in which they were painted. It has been reported that Pollock’s paintings are fractal and that this feature was more evident in his later works. However, our results show that the fractal dimension of these paintings ranges among values close to two. We characterize this behavior as a fractal-order transition. Based on the study of disorder-order transition in physical systems, we interpreted the fractal-ordermore » transition via the dark paint strokes in Pollock’s paintings as structured lines that follow a power law measured by the fractal dimension. We determined self-similarity in specific paintings, thereby demonstrating an important dependence on the scale of observations. We also characterized the fractal spectrum for the painting entitled Teri’s Find. We obtained similar spectra for Teri’s Find and Number 5, thereby suggesting that the fractal dimension cannot be rejected completely as a quantitative parameter for authenticating these artworks. -- Highlights: •We determined the degree of order in Jackson Pollock paintings using the Hausdorff–Besicovitch dimension. •We detected a fractal-order transition from Pollock’s paintings between 1947 and 1951. •We suggest that Jackson Pollock could have painted Teri’s Find.« less

Modeling metal droplet sprays in spray forming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muoio, N.G.; Crowe, C.T.; Fritsching, U.

1995-12-31

Spray casting is a process whereby a molten metal stream is atomized and deposited on a substrate. The rapid solidification of the metal droplets gives rise to a fine grain structure and improved material properties. This paper presents a simulation for the fluid and thermal interaction of the fluid and droplets in the spray and the effect on the droplet spray pattern. Good agreement is obtained between the measured and predicted droplet mass flux distribution in the spray.

Accelerated bridge paint test program.

DOT National Transportation Integrated Search

2011-07-06

The accelerated bridge paint (AB-Paint) program evaluated a new Sherwin-Williams two-coat, : fast-curing paint system. The system is comprised of an organic zinc-rich primer (SW Corothane I : Galvapac One-Pack Zinc-Rich Primer B65 G11) and a polyurea...

Paint-Stirrer Submarine

ERIC Educational Resources Information Center

Young, Jocelyn; Hardy, Kevin

2007-01-01

In this article, the authors discuss a unique and challenging laboratory exercise called, the paint-stir-stick submarine, that keeps the students enthralled. The paint-stir-stick submarine fits beautifully with the National Science Education Standards Physical Science Content Standard B, and with the California state science standards for physical…

Chromate Dermatitis from Paint

PubMed Central

Engel, H. O.; Calnan, C. D.

1963-01-01

Among 250 workers engaged on wet sandpapering of primer paint on car bodies 65 developed a contact dermatitis. The average latent period before dermatitis developed was 4·6 months: only 60% of the patients made a completely satisfactory recovery. The average duration of dermatitis was 5·3 months. Two thirds of the men used one of two barrier creams supplied, while one third used none. Routine patch testing showed that the majority was allergic to chromate. It was found that a primer paint contained zinc chromate, which had been introduced into the paint by the manufacturers shortly before the first cases occurred. Removal of chromate from the paint resulted in a prompt cessation of new cases of dermatitis. Images PMID:14046155

Tanjore: Mystical Painting of India

ERIC Educational Resources Information Center

Henn, Cynthia A.

2004-01-01

Tanjore (or Thanjavur or Thanlavoor) paintings are one of the most popular traditional art forms in Southern India. These ornate religious paintings involve Hindu mythology. The paintings are noted for their adornment of gold and semiprecious stones such as rubies, emeralds, and pearls. Currently, the semiprecious stones are often substituted…

Pollock without Paint?

ERIC Educational Resources Information Center

Sutley, Jane

2011-01-01

This article describes how the author exposes her students to the world of Jackson Pollock, the artist who brings to mind dripping, meandering, splashing puddles of paint. Pollock's action paintings of the late 1940s-'50s call out for unfettered movement, fluidity, and freedom of application. Is it even possible to capture the action, rhythm and…

Overview of paint removal methods

NASA Astrophysics Data System (ADS)

Foster, Terry

1995-04-01

With the introduction of strict environmental regulations governing the use and disposal of methylene chloride and phenols, major components of chemical paint strippers, there have been many new environmentally safe and effective methods of paint removal developed. The new methods developed for removing coatings from aircraft and aircraft components include: mechanical methods using abrasive media such as plastic, wheat starch, walnut shells, ice and dry ice, environmentally safe chemical strippers and paint softeners, and optical methods such as lasers and flash lamps. Each method has its advantages and disadvantages, and some have unique applications. For example, mechanical and abrasive methods can damage sensitive surfaces such as composite materials and strict control of blast parameters and conditions are required. Optical methods can be slow, leaving paint residues, and chemical methods may not remove all of the coating or require special coating formulations to be effective. As an introduction to environmentally safe and effective methods of paint removal, this paper is an overview of the various methods available. The purpose of this overview is to introduce the various paint removal methods available.

Standard Operating Procedure for the Preparation of Lead-Containing Paint Films and Lead-in-Paint Diagnostic Test Materials

EPA Science Inventory

This SOP describes the preparation of stand-alone, lead paint films, prepared according to the old paint recipes. Further, this SOP describes the use of these paint films for the preparation of simulated old paints on a variety of substrates. Substrates used included wood, stee...

Replacement of corrosion protection chromate primers and paints used in cryogenic applications on the Space Shuttle with wire arc sprayed aluminum coatings

NASA Technical Reports Server (NTRS)

Daniel, R. L.; Sanders, H. L.; Zimmerman, F. R.

1995-01-01

With the advent of new environmental laws restricting volatile organic compounds and hexavalent chrome emissions, 'environmentally safe' thermal spray coatings are being developed to replace the traditional corrosion protection chromate primers. A wire arc sprayed aluminum coating is being developed for corrosion protection of low pressure liquid hydrogen carrying ducts on the Space Shuttle Main Engine. Currently, this hardware utilizes a chromate primer to provide protection against corrosion pitting and stress corrosion cracking induced by the cryogenic operating environment. The wire are sprayed aluminum coating has been found to have good potential to provide corrosion protection for flight hardware in cryogenic applications. The coating development, adhesion test, corrosion test and cryogenic flexibility test results will be presented.

Laser paint removal on the outside walls of the Church Abbey Saint Adoeno in Bisceglie (BAT), Italy: a case study

NASA Astrophysics Data System (ADS)

Daurelio, G.; Catalano, I. M.; Bassi, P.

2010-09-01

It is the oldest church in the city after the cathedral. It is among the purest examples of Romanesque. It was founded in 1074 and expenses for its construction helped the inhabitants of the agricultural hamlets of the Cirignano, Pacciano and Zappino. The church was dedicated to St. Adoeno Dado, bishop of Rouen, protector of Norman, because , according to tradition, the building also participated Norman soldiers. San Adoeno church has a façade at cusp with a truncated tympanum , crowned by an eagle. In the centre of the façade there is a rose ornament surrounded by four lions and a statue of St. Adoeno ( Figs. A to I ). On the outside walls of this Abbey many graffiti, produced by different coloured spray paints were found. After the usual photographical tests some Laser Paint Removal trials were executed to verify the damage threshold of the calcareous stony substrate as well as the possibility to ablate these paints by a Nd - YAG laser in Q-Switch mode. Even if all the classical four laser paint ablation techniques were employed some paints showed a great difficulty to be removed from the substrate. For these ones it was necessary to increase at maximum both the energy per pulse and the fluence value for obtaining some acceptable result but the substrate looked turned pale. It was decided to remove a small amount of these paints and subject to chemical analysis for determining whether they were acrylic based. At the same time it was investigated on the type of limestone substrate that appeared more porous and less hard on the surface than the common local limestone marble basin, that is, Trani or Bisceglie. So, on the light of these investigations, the possible solution for this hard laser ablation problem was carried out with an acceptable final result.

Direct identification of various copper phthalocyanine pigments in automotive paints and paint smears by laser desorption ionization mass spectrometry.

PubMed

Mukai, Tadashi; Nakazumi, Hiroyuki; Kawabata, Shin-ichirou; Kusatani, Masaru; Nakai, Seita; Honda, Sadao

2008-01-01

Direct identification of copper phthalocyanine (CuPc) and chlorinated CuPcs in paints for discrimination between blue automobile paints by means of laser desorption mass spectrometry (LDMS) in the absence of a matrix is reported. The models consisted of eight commercially available CuPc pigments applied to a piece of plain white coating paper. The relationship between the peak intensity at m/z 575 of the CuPc, the number of pulsed laser shots, and laser power was compared to optimize laser abrasion. LDMS analysis of the model paints demonstrated that all characteristic components of the CuPc pigments in the paint films were in good agreement with those in the powder pigments. Further, the chlorinated CuPcs in the paint films could be distinguished. A quantity of 42 blue paint films, representing the paints used for painting Japanese domestic trucks, was examined by LDMS analysis. Results indicate that the paints can be classified into four categories based on the chlorinated CuPc components of the paints. Therefore, LDMS spectra of CuPc pigments would be useful for the identification of paints in forensic investigations. Herein, we report the successful identification of the CuPcs in a paint smear on the frame of a bicycle damaged in a hit-and-run accident, using the LDMS spectra.

[Illness caused by water-based paints?].

PubMed

Birkeland, G; Zahlsen, K; Aas, K

1994-08-20

Illness caused by the indoor environment is a challenging and complicated field to investigate. Emissions from paints may contribute to the problems. Several components of water-based paints evaporate for a long time after painting, and some of them may affect human biology. We describe one patient who has experienced symptoms caused by water-based paint. Different reaction mechanisms may be involved, and these are discussed. Components which may elicit biological effects are listed and discussed. Physicians should be aware of the possibility that a few patients may suffer from illness caused by emissions from modern paints.

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2010 CFR

2010-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2014 CFR

2014-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2013 CFR

2013-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2012 CFR

2012-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2011 CFR

2011-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

Jasper Johns' Painted Words.

ERIC Educational Resources Information Center

Levinger, Esther

1989-01-01

States that the painted words in Jasper Johns' art act in two different capacities: concealed words partake in the artist's interrogation of visual perception; and visible painted words question classical representation. Argues that words are Johns' means of critiquing modernism. (RS)

An overview of spray drift reduction testing of spray nozzles

USDA-ARS?s Scientific Manuscript database

The importance of the development and testing of drift reduction technologies (DRTs) is increasing. Common spray drift reduction technologies include spray nozzles and spray adjuvants. Following draft procedures developed for a DRT program, three spray nozzles were tested under high air speed cond...

Influence of Cold-Sprayed, Warm-Sprayed, and Plasma-Sprayed Layers Deposition on Fatigue Properties of Steel Specimens

NASA Astrophysics Data System (ADS)

Cizek, J.; Matejkova, M.; Dlouhy, I.; Siska, F.; Kay, C. M.; Karthikeyan, J.; Kuroda, S.; Kovarik, O.; Siegl, J.; Loke, K.; Khor, Khiam Aik

2015-06-01

Titanium powder was deposited onto steel specimens using four thermal spray technologies: plasma spray, low-pressure cold spray, portable cold spray, and warm spray. The specimens were then subjected to strain-controlled cyclic bending test in a dedicated in-house built device. The crack propagation was monitored by observing the changes in the resonance frequency of the samples. For each series, the number of cycles corresponding to a pre-defined specimen cross-section damage was used as a performance indicator. It was found that the grit-blasting procedure did not alter the fatigue properties of the steel specimens (1% increase as compared to as-received set), while the deposition of coatings via all four thermal spray technologies significantly increased the measured fatigue lives. The three high-velocity technologies led to an increase of relative lives to 234% (low-pressure cold spray), 210% (portable cold spray), and 355% (warm spray) and the deposition using plasma spray led to an increase of relative lives to 303%. The observed increase of high-velocity technologies (cold and warm spray) could be attributed to a combination of homogeneous fatigue-resistant coatings and induction of peening stresses into the substrates via the impingement of the high-kinetic energy particles. Given the intrinsic character of the plasma jet (low-velocity impact of semi/molten particles) and the mostly ceramic character of the coating (oxides, nitrides), a hypothesis based on non-linear coatings behavior is provided in the paper.

Evaluation of yellow-white paint mixtures.

DOT National Transportation Integrated Search

1980-01-01

In view of the potential cost savings to be achieved through the use of the regular yellow traffic paint diluted with less expensive white paint, it was decided that the Department would evaluate roadway applications of the paint mixture with emphasi...

Artists Paint ... Landscapes

ERIC Educational Resources Information Center

Herberholz, Barbara

2012-01-01

This article features the painting "View of Toledo," based on Toledo, a very old city located on a high plateau in Spain. By the time the artist El Greco painted the picture, he had lived there for 31 years. When one looks at the picture, one will see a storm approaching and will see the city as if it were lit by a flash of lightning. What main…

24 CFR 200.800 - Lead-based paint.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 2 2012-04-01 2012-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

24 CFR 200.800 - Lead-based paint.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 2 2013-04-01 2013-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

24 CFR 200.800 - Lead-based paint.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 2 2014-04-01 2014-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

24 CFR 200.800 - Lead-based paint.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 2 2011-04-01 2011-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

24 CFR 200.800 - Lead-based paint.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Lead-based paint. 200.800 Section... DEVELOPMENT GENERAL INTRODUCTION TO FHA PROGRAMS Lead-Based Paint Poisoning Prevention § 200.800 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

Measurement, modeling and perception of painted surfaces: A Multi-scale Analysis of the Touch-up Problem

NASA Astrophysics Data System (ADS)

Kalghatgi, Suparna Kishore

Real-world surfaces typically have geometric features at a range of spatial scales. At the microscale, opaque surfaces are often characterized by bidirectional reflectance distribution functions (BRDF), which describes how a surface scatters incident light. At the mesoscale, surfaces often exhibit visible texture -- stochastic or patterned arrangements of geometric features that provide visual information about surface properties such as roughness, smoothness, softness, etc. These textures also affect how light is scattered by the surface, but the effects are at a different spatial scale than those captured by the BRDF. Through this research, we investigate how microscale and mesoscale surface properties interact to contribute to overall surface appearance. This behavior is also the cause of the well-known "touch-up problem" in the paint industry, where two regions coated with exactly the same paint, look different in color, gloss and/or texture because of differences in application methods. At first, samples were created by applying latex paint to standard wallboard surfaces. Two application methods- spraying and rolling were used. The BRDF and texture properties of the samples were measured, which revealed differences at both the microscale and mesoscale. This data was then used as input for a physically-based image synthesis algorithm, to generate realistic images of the surfaces under different viewing conditions. In order to understand the factors that govern touch-up visibility, psychophysical tests were conducted using calibrated, digital photographs of the samples as stimuli. Images were presented in pairs and a two alternative forced choice design was used for the experiments. These judgments were then used as data for a Thurstonian scaling analysis to produce psychophysical scales of visibility, which helped determine the effect of paint formulation, application methods, and viewing and illumination conditions on the touch-up problem. The results can be

Automated Laser Paint Stripping (ALPS) update

NASA Astrophysics Data System (ADS)

Lovoi, Paul

1993-03-01

To date, the DoD has played a major role in funding a number of paint stripping programs. Some technologies have proven less effective than contemplated. Others are still in the validation phase. Paint stripping is one of the hottest issues being addressed by the finishing industry since the Environmental Protection Agency (EPA) has mandated that chemical stripping using methylene chloride/phenolic type strippers be stopped. The DoD and commercial aircraft companies are hard-pressed to find an alternative. Automated laser paint stripping has been identified as a technique for removing coatings from aircraft surfaces. International Technical Associates (InTA) was awarded a Navy contract for an automated laser paint stripping system (ALPS) that will remove paint from metallic and composite substrates. For the program, which will validate laser paint stripping, InTA will design, build, test, and install a system for fighter-sized aircraft at both the Norfolk and North Island (San Diego) Aviation Depots.

Paint-only is equivalent to scrub-and-paint in preoperative preparation of abdominal surgery sites.

PubMed

Ellenhorn, Joshua D I; Smith, David D; Schwarz, Roderich E; Kawachi, Mark H; Wilson, Timothy G; McGonigle, Kathryn F; Wagman, Lawrence D; Paz, I Benjamin

2005-11-01

Antiseptic preoperative skin site preparation is used to prepare the operative site before making a surgical incision. The goal of this preparation is a reduction in postoperative wound infection. The most straightforward technique necessary to achieve this goal remains controversial. A prospective randomized trial was designed to prove equivalency for two commonly used techniques of surgical skin site preparation. Two hundred thirty-four patients undergoing nonlaparoscopic abdominal operations were consented for the trial. Exclusion criteria included presence of active infection at the time of operation, neutropenia, history of skin reaction to iodine, or anticipated insertion of prosthetic material at the time of operation. Patients were randomized to receive either a vigorous 5-minute scrub with povidone-iodine soap, followed by absorption with a sterile towel, and a paint with aqueous povidone-iodine or surgical site preparation with a povidone-iodine paint only. The primary end point of the study was wound infection rate at 30 days, defined as presence of clinical signs of infection requiring therapeutic intervention. Patients randomized to the scrub-and-paint arm (n = 115) and the paint-only arm (n = 119) matched at baseline with respect to age, comorbidity, wound classification, mean operative time, placement of drains, prophylactic antibiotic use, and surgical procedure (all p > 0.09). Wound infection occurred in 12 (10%) scrub-and-paint patients, and 12 (10%) paint-only patients. Based on our predefined equivalency parameters, we conclude equivalence of infection rates between the two preparations. Preoperative preparation of the abdomen with a scrub with povidone-iodine soap followed by a paint with aqueous povidone-iodine can be abandoned in favor of a paint with aqueous povidone-iodine alone. This change will result in reductions in operative times and costs.

24 CFR 574.635 - Lead-based paint.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

24 CFR 511.15 - Lead-based paint.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Lead-based paint. 511.15 Section... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

24 CFR 574.635 - Lead-based paint.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 3 2012-04-01 2012-04-01 false Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

24 CFR 574.635 - Lead-based paint.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

24 CFR 511.15 - Lead-based paint.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 3 2012-04-01 2012-04-01 false Lead-based paint. 511.15 Section... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

24 CFR 574.635 - Lead-based paint.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 3 2014-04-01 2013-04-01 true Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

24 CFR 511.15 - Lead-based paint.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Lead-based paint. 511.15 Section... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

24 CFR 574.635 - Lead-based paint.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Lead-based paint. 574.635 Section....635 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations...

24 CFR 1003.607 - Lead-based paint.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

24 CFR 1003.607 - Lead-based paint.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 4 2013-04-01 2013-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

24 CFR 511.15 - Lead-based paint.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 3 2014-04-01 2013-04-01 true Lead-based paint. 511.15 Section 511... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

24 CFR 511.15 - Lead-based paint.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Lead-based paint. 511.15 Section 511... Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and implementing regulations at...

24 CFR 1003.607 - Lead-based paint.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

24 CFR 1003.607 - Lead-based paint.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

24 CFR 1003.607 - Lead-based paint.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Lead-based paint. 1003.607 Section... § 1003.607 Lead-based paint. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of 1992 (42 U.S.C. 4851-4856), and...

The colors of paintings and viewers' preferences.

PubMed

Nascimento, Sérgio M C; Linhares, João M M; Montagner, Cristina; João, Catarina A R; Amano, Kinjiro; Alfaro, Catarina; Bailão, Ana

2017-01-01

One hypothesis to explain the aesthetics of paintings is that it depends on the extent to which they mimic natural image statistics. In fact, paintings and natural scenes share several statistical image regularities but the colors of paintings seem generally more biased towards red than natural scenes. Is the particular option for colors in each painting, even if less naturalistic, critical for perceived beauty? Here we show that it is. In the experiments, 50 naïve observers, unfamiliar with the 10 paintings tested, could rotate the color gamut of the paintings and select the one producing the best subjective impression. The distributions of angles obtained are described by normal distributions with maxima deviating, on average, only 7 degrees from the original gamut orientation and full width at half maximum just above the threshold to perceive a chromatic change in the paintings. Crucially, for data pooled across observers and abstract paintings the maximum of the distribution was at zero degrees, i.e., the same as the original. This demonstrates that artists know what chromatic compositions match viewers' preferences and that the option for less naturalistic colors does not constrain the aesthetic value of paintings. Copyright © 2016 Elsevier Ltd. All rights reserved.

Improved Intumescent Paint

DTIC Science & Technology

1977-02-07

addition of Experimental Resin XD-8217 to a commercial acrylic interior house paint. Coatings modified in this -12- FIGURE 3 TESTING APPARATUS FOR 30-MINUTE...express or implied, is given nor is freedcm from any patent owned by The Dow Chemical Company or by others to be inferred. IIMPROVED INTUMESCENT PAINT...properties of a commercial microsphere product, designated as Experimental Resin XD-8217.00 and manufactured by The Dow Chemical Company. The halogenated

Drawing and Painting with Under-Threes.

ERIC Educational Resources Information Center

Kolbe, Ursula; Smyth, Jane

2000-01-01

Noting that drawing and painting offer very young children powerful ways to explore and communicate thoughts and feelings, this booklet for caregivers and teachers offers suggestions related to painting and drawing for children under 3 years. The booklet discusses what young children can do with drawing and painting materials, including exploring…

What's Behind A Painting?

Treesearch

John Zasada

2001-01-01

In art galleries, one often studies a painting from various angles and distances, seeking to discover all that is possible about the method and style of the artist and what the artist is trying to communicate. In other words the observer is trying to detremine "what is behind the painting."

Lead paint removal with high-intensity light pulses.

PubMed

Grapperhaus, Michael J; Schaefer, Raymond B

2006-12-15

This paper presents the results of an initial investigation into using high-intensity incoherent light pulses to strip paint. Measurements of light pulse characteristics, the reflectivity of different paints and initial experiments on the threshold for paint removal, and paint removal are presented, along with an approximate model consistent with experimental results. Paint removal tests include lead paint, the reduction of lead levels to below levels required for lead abatement, as well as air and light emissions measurements that are within regulatory guidelines.

Paint for detection of radiological or chemical agents

DOEpatents

Farmer, Joseph C [Tracy, CA; Brunk, James L [Martinez, CA; Day, Sumner Daniel [Danville, CA

2010-08-24

A paint that warns of radiological or chemical substances comprising a paint operatively connected to the surface, an indicator material carried by the paint that provides an indication of the radiological or chemical substances, and a thermo-activation material carried by the paint. In one embodiment, a method of warning of radiological or chemical substances comprising the steps of painting a surface with an indicator material, and monitoring the surface for indications of the radiological or chemical substances. In another embodiment, a paint is operatively connected to a vehicle and an indicator material is carried by the paint that provides an indication of the radiological or chemical substances.

Effect of spray angle and spray volume on deposition of a medium droplet spray with air support in ivy pot plants.

PubMed

Foqué, Dieter; Pieters, Jan G; Nuyttens, David

2014-03-01

Spray boom systems, an alternative to the predominantly-used spray guns, have the potential to considerably improve crop protection management in glasshouses. Based on earlier experiments, the further optimization of the deposits of a medium spray quality extended range flat fan nozzle type using easy adjustable spray boom settings was examined. Using mineral chelate tracers and water sensitive papers, the spray results were monitored at three plant levels, on the upper side and the underside of the leaves, and on some off-target collectors. In addition, the deposition datasets of all tree experiments were compared. The data showed that the most efficient spray distribution with the medium spray quality flat fan nozzles was found with a 30° forward angled spray combined with air support and an application rate of 1000 L ha(-1) . This technique resulted in a more uniform deposition in the dense canopy and increased spray deposition on the lower side of the leaves compared with the a standard spray boom application. Applying 1000 L ha(-1) in two subsequent runs instead of one did not seem to show any added value. Spray deposition can be improved hugely simply by changing some spray boom settings like nozzle type, angling the spray, using air support and adjusting the spray volume to the crop. © 2013 Society of Chemical Industry.

Chromate content versus particle size for aircraft paints.

PubMed

LaPuma, Peter T; Rhodes, Brian S

2002-12-01

Many industries rely on the corrosion inhibiting properties of chromate-containing primer paints to protect metal from oxidation. However, chromate contains hexavalent chromium (Cr(6+)), a known human carcinogen. The concentration of Cr(6+) as a function of paint particle size has important implications to worker health and environmental release from paint facilities. This research examines Cr(6+) content as a function of particle size for three types of aircraft primer paints: solvent-based epoxy-polyamide, water-based epoxy-polyamide, and solvent-based polyurethane. Cascade impactors were used to collect and separate paint particles based on their aerodynamic diameter, from 0.7 to 34.1 microm. The mass of the dry paint collected at each stage was determined and an atomic absorption spectrometer was used to analyze for Cr(6+) content. For all three paints, particles less than 7.0 microm contained disproportionately less Cr(6+) per mass of dry paint than larger particles, and the Cr(6+)concentration decreased substantially as particle size decreased. The smallest particles, 0.7 to 1.0 microm, contained approximately 10% of the Cr(6+) content, per mass of dry paint, compared to particles larger than 7.0 microm. The paint gun settings of air to paint ratio was found to have no influence on the Cr(6+) bias.

Characterization of sprays

NASA Technical Reports Server (NTRS)

Chigier, N.; Mao, C.-P.

1984-01-01

It is pointed out that most practical power generation and propulsion systems involve the burning of different types of fuel sprays, taking into account aircraft propulsion, industrial furnaces, boilers, gas turbines, and diesel engines. There has been a lack of data which can serve as a basis for spray model development and validation. A major aim of the present investigation is to fill this gap. Experimental apparatus and techniques for studying the characteristics of fuel sprays are discussed, taking into account two-dimensional still photography, cinematography, holography, a laser diffraction particle sizer, and a laser anemometer. The considered instruments were used in a number of experiments, taking into account three different types of fuel spray. Attention is given to liquid fuel sprays, high pressure pulsed diesel sprays, and coal-water slurry sprays.

Laser paint stripping

NASA Astrophysics Data System (ADS)

Head, J. D.; Niedzielski, J. Peter

1991-06-01

A study to assess the utility of high powered CO2 pulsed laser depainting methods was conducted on aluminum and graphite epoxy composites. The various tests were designed to detect potential forms of damage or loss of properties of various aircraft structural materials during removal of paint with pulsed laser energy. Tests for changes in physical properties, paint adhesion and corrosion protection of repainted materials showed no detectable adverse changes in any of the samples studied.

Terahertz imaging for subsurface investigation of art paintings

NASA Astrophysics Data System (ADS)

Locquet, A.; Dong, J.; Melis, M.; Citrin, D. S.

2017-08-01

Terahertz (THz) reflective imaging is applied to the stratigraphic and subsurface investigation of oil paintings, with a focus on the mid-20th century Italian painting, `After Fishing', by Ausonio Tanda. THz frequency-wavelet domain deconvolution, which is an enhanced deconvolution technique combining frequency-domain filtering and stationary wavelet shrinkage, is utilized to resolve the optically thin paint layers or brush strokes. Based on the deconvolved terahertz data, the stratigraphy of the painting including the paint layers is reconstructed and subsurface features are clearly revealed. Specifically, THz C-scans and B-scans are analyzed based on different types of deconvolved signals to investigate the subsurface features of the painting, including the identification of regions with more than one paint layer, the refractive-index difference between paint layers, and the distribution of the paint-layer thickness. In addition, THz images are compared with X-ray images. The THz image of the thickness distribution of the paint exhibits a high degree of correlation with the X-ray transmission image, but THz images also reveal defects in the paperboard that cannot be identified in the X-ray image. Therefore, our results demonstrate that THz imaging can be considered as an effective tool for the stratigraphic and subsurface investigation of art paintings. They also open up the way for the use of non-ionizing THz imaging as a potential substitute for ionizing X-ray analysis in nondestructive evaluation of art paintings.

Mapping the opacity of paint layers in paintings with coloured grounds using optical coherence tomography

NASA Astrophysics Data System (ADS)

Liu, Ping; Hall-Aquitania, Moorea; Hermens, Erma; Groves, Roger M.

2017-07-01

Optical diagnostics techniques are becoming important for technical art history (TAH) as well as for heritage conservation. In recent years, optical coherence tomography (OCT) has been increasingly used as a novel technique for the inspection of artwork, revealing the stratigraphy of paintings. It has also shown to be an effective tool for vanish layer inspection. OCT is a contactless and non-destructive technique for microstructural imaging of turbid media, originally developed for medical applications. However current OCT instruments have difficulty in paint layer inspection due to the opacity of most pigments. This paper explores the potential of OCT for the investigation of paintings with coloured grounds. Depth scans were processed to determine the light penetration depth at the optical wavelength based on a 1/e light attenuation calculation. The variation in paint opacity was mapped based on the microstructural images and 3D penetration depth profiles was calculated and related back to the construction of the artwork. By determining the light penetration depth over a range of wavelengths the 3D depth perception of a painting with coloured grounds can be characterized optically.

Pigeons' discrimination of paintings by Monet and Picasso

PubMed Central

Watanabe, Shigeru; Sakamoto, Junko; Wakita, Masumi

1995-01-01

Pigeons successfully learned to discriminate color slides of paintings by Monet and Picasso. Following this training, they discriminated novel paintings by Monet and Picasso that had never been presented during the discrimination training. Furthermore, they showed generalization from Monet's to Cezanne's and Renoir's paintings or from Picasso's to Braque's and Matisse's paintings. These results suggest that pigeons' behavior can be controlled by complex visual stimuli in ways that suggest categorization. Upside-down images of Monet's paintings disrupted the discrimination, whereas inverted images of Picasso's did not. This result may indicate that the pigeons' behavior was controlled by objects depicted in impressionists' paintings but was not controlled by objects in cubists' paintings. PMID:16812755

Layered growth with bottom-spray granulation for spray deposition of drug.

PubMed

Er, Dawn Z L; Liew, Celine V; Heng, Paul W S

2009-07-30

The gap in scientific knowledge on bottom-spray fluidized bed granulation has emphasized the need for more studies in this area. This paper comparatively studied the applicability of a modified bottom-spray process and the conventional top-spray process for the spray deposition of a micronized drug during granulation. The differences in circulation pattern, mode of growth and resultant granule properties between the two processes were highlighted. The more ordered and consistent circulation pattern of particles in a bottom-spray fluidized bed was observed to give rise to layered granule growth. This resulted in better drug content uniformity among the granule batches and within a granule batch. The processes' sensitivities to wetting and feed material characteristics were also compared and found to differ markedly. Less robustness to differing process conditions was observed for the top-spray process. The resultant bottom-spray granules formed were observed to be less porous, more spherical and had good flow properties. The bottom-spray technique can thus be potentially applied for the spray deposition of drug during granulation and was observed to be a good alternative to the conventional technique for preparing granules.

Disposal of bridge paint residue.

DOT National Transportation Integrated Search

2005-12-01

Paint residue generated by bridge maintenance painting commonly contains lead requiring the residue to be disposed of as a hazardous waste. Several alternatives are being investigated in this study, chemical stabilization and recycling as options for...

MC Contracting, Paint, & Roofing, LLC Information Sheet

EPA Pesticide Factsheets

MC Contracting, Paint, & Roofing, LLC, d/b/a M.C. Painting & Contractor and M.C. Painting Group (the Company) is located in Philadelphia, Pennsylvania. The settlement involves renovation activities conducted at property constructed prior to 1978.

Notification: EPA's Implementation and Enforcement of the Lead-Based Paint Renovation, Repair and Painting Rule

EPA Pesticide Factsheets

Project #OA&E-FY18-0162, March 28, 2018. The OIG plans to begin preliminary research to evaluate the EPA's implementation and enforcement of the Lead-Based Paint Renovation, Repair and Painting Rule (RRP).

Stripping Paint From Exterior Wood Surfaces

Treesearch

Mark T. Knaebe

2013-01-01

Removing paint and other film-forming finishes is a time consuming and often difficult process. In some cases, finishes need to be removed prior to repainting; for example, if the old surface is covered with severely peeled or blistered paint or if excessive paint buildup has caused cross-grain cracking. You must also remove the finish before applying a penetrating...

Effect of spray application technique on spray deposition in greenhouse strawberries and tomatoes.

PubMed

Braekman, Pascal; Foque, Dieter; Messens, Winy; Van Labeke, Marie-Christine; Pieters, Jan G; Nuyttens, David

2010-02-01

Increasingly, Flemish greenhouse growers are using spray booms instead of spray guns to apply plant protection products. Although the advantages of spray booms are well known, growers still have many questions concerning nozzle choice and settings. Spray deposition using a vertical spray boom in tomatoes and strawberries was compared with reference spray equipment. Five different settings of nozzle type, size and pressure were tested with the spray boom. In general, the standard vertical spray boom performed better than the reference spray equipment in strawberries (spray gun) and in tomatoes (air-assisted sprayer). Nozzle type and settings significantly affected spray deposition and crop penetration. Highest overall deposits in strawberries were achieved using air-inclusion or extended-range nozzles. In tomatoes, the extended-range nozzles and the twin air-inclusion nozzles performed best. Using smaller-size extended-range nozzles above the recommended pressure range resulted in lower deposits, especially inside the crop canopy. The use of a vertical spray boom is a promising technique for applying plant protection products in a safe and efficient way in tomatoes and strawberries, and nozzle choice and setting should be carefully considered.

40 CFR 745.233 - Lead-based paint activities requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Lead-based paint activities...

40 CFR 745.233 - Lead-based paint activities requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Lead-based paint activities...

40 CFR 745.233 - Lead-based paint activities requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Lead-based paint activities...

40 CFR 745.233 - Lead-based paint activities requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Lead-based paint activities...

40 CFR 745.233 - Lead-based paint activities requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) TOXIC SUBSTANCES CONTROL ACT LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Lead-Based Paint Activities § 745.233 Lead-based paint activities requirements. Lead-based paint... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Lead-based paint activities...

LSST Painting Risk Evaluation Memo

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wolfe, Justin E.

The optics subsystem is required to paint the edges of optics black where possible. Due to the risks in applying the paint LSST requests a review of the impact of removing this requirement for the filters and L3.

Comparison of the performance between a spray gun and a spray boom in ornamentals.

PubMed

Foqué, D; Nuyttens, D

2011-01-01

Flemish greenhouse growers predominantly use handheld spray guns and spray lances for their crop protection purposes although these techniques are known for their heavy workload and their high operator exposure risks. Moreover, when these techniques are compared with spray boom equipment, they are often found to be less effective. On the other hand, handheld spraying techniques are less expensive and more flexible to use. Additionally, many Flemish growers are convinced that a high spray volume and spray pressure is needed to assure a good plant protection. The aim of this work was to evaluate and compare the spray deposition, penetration and uniformity between a manually pulled horizontal spray boom and a spray gun under controlled laboratory conditions. In total, six different spray application techniques were evaluated. In general, the total deposition results were comparable between the spray boom and the spray gun applications but the boom applications resulted in a more uniform spray distribution over the crop. On a plant level, the spray distribution was not uniform for the different techniques with highest deposits on the upper side of the top leaves. Using spray guns at a higher spray pressure did not improve spray penetration and deposition on the bottom side of the leaves. From the different nozzle types, the XR 80 03 gave the best results. Plant density clearly affected crop penetration and deposition on the bottom side of the leaves.

24 CFR 598.408 - Lead-based paint requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

24 CFR 598.408 - Lead-based paint requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

24 CFR 598.408 - Lead-based paint requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 3 2014-04-01 2013-04-01 true Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

24 CFR 598.408 - Lead-based paint requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 3 2012-04-01 2012-04-01 false Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

24 CFR 598.408 - Lead-based paint requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Lead-based paint requirements. 598... DESIGNATIONS Post-Designation Requirements § 598.408 Lead-based paint requirements. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based Paint Hazard Reduction Act of...

Paint removal activities in Germany

NASA Astrophysics Data System (ADS)

Holbein, R.; Arnolds-Mayer, G.

1993-03-01

To replace paint removing chemicals containing chlorinated hydrocarbons several alternative paint stripping methods have been developed or are under study in Germany: high pressure water stripping; plastic media blasting; use of alcalic and acid activated softeners; CO2 pellet blasting; and laser application.

EMISSIONS OF ODOROUS ALDEHYDES FROM ALKYD PAINT

EPA Science Inventory

Aldehyde emissions are widely held responsible for the acrid after-odor of drying alkyd-based paint films. The aldehyde emissions from three different alkyd paints were measured in small environmental chambers. It was found that, for each alkyd paint applied, more than 2 mg of ...

Paint removal activities in Canada

NASA Astrophysics Data System (ADS)

Foster, Terry

1993-03-01

Paint removal activities currently under way in Canada include: research and development of laser paint stripping; development and commercialization of a new blasting medium based on wheat starch; commercialization of a new blasting medium and process using crystalline ice blasting for paint removal and surface cleaning; and the development of automated and robotic systems for paint stripping applications. A specification for plastic media blasting (PMB) of aircraft and aircraft components is currently being drafted by NDHQ for use by the Canadian Armed Forces (CAF) and contractors involved in coating removal for the CAF. Defense Research Establishment Pacific (DREP) is studying the effects of various blast media on coating removal rates, and minimizing the possibility of damage to substrates other than aluminum such as graphite epoxy composite and Kevlar. The effects of plastic media blasting on liquid penetrant detection of fatigue cracks is also under investigation.

Mural Painting as Inclusive Art Learning Experience

ERIC Educational Resources Information Center

Ho, Kong

2010-01-01

Traditional art education, like other academic disciplines, emphasizes competitiveness and individualism. Through a mural painting curriculum, learners participate in mural art and history appreciation, are active in mural theme or content construction, and engage in hands-on mural design and painting processes. When mural paintings are produced…

Foliar spray banding characteristics

Treesearch

A.R. Womac; C.W. Smith; Joseph E. Mulrooney

2004-01-01

Foliar spray banding was explored as a means of reducing peticide use compared to broadcast applications. Barious geometric spray patterns and delivery angles of foliar spray bands were investigated to increase spray deposits in a crop row at a constant spray rate of 94 L/ha. Wind-free laboratory results indicated that a banded application using three 65° hollow-cone...

A quantitative approach to painting styles

NASA Astrophysics Data System (ADS)

Vieira, Vilson; Fabbri, Renato; Sbrissa, David; da Fontoura Costa, Luciano; Travieso, Gonzalo

2015-01-01

This research extends a method previously applied to music and philosophy (Vilson Vieira et al., 2012), representing the evolution of art as a time-series where relations like dialectics are measured quantitatively. For that, a corpus of paintings of 12 well-known artists from baroque and modern art is analyzed. A set of 99 features is extracted and the features which most contributed to the classification of painters are selected. The projection space obtained provides the basis to the analysis of measurements. These quantitative measures underlie revealing observations about the evolution of painting styles, specially when compared with other humanity fields already analyzed: while music evolved along a master-apprentice tradition (high dialectics) and philosophy by opposition, painting presents another pattern: constant increasing skewness, low opposition between members of the same movement and opposition peaks in the transition between movements. Differences between baroque and modern movements are also observed in the projected "painting space": while baroque paintings are presented as an overlapped cluster, the modern paintings present minor overlapping and are disposed more widely in the projection than the baroque counterparts. This finding suggests that baroque painters shared aesthetics while modern painters tend to "break rules" and develop their own style.

THE HAZARDS OF PAINTING AND VARNISHING 1965

PubMed Central

Piper, Robert

1965-01-01

A review of paint hazards is made, giving brief descriptions of methods of application in use in 1965, of paint usage according to resin base, and of paint ingredients. The most interesting and complex of these are the resin bases, which have much in common with plastics. Reference is made to some of the many minor ingredients. The problem of keeping abreast of the possible toxic effects, so that paint manufacturers and their customers may be warned and protected, will be clear. PMID:5836564

Paint removal activities in the US Navy

NASA Astrophysics Data System (ADS)

Kozol, Joseph

1993-03-01

Use of methylene chloride and phenol based chemical strippers for aircraft paint removal generates large quantities of hazardous waste and creates health and safety problems for operating personnel. This paper presents an overview of the U.S. Navy's activities in the investigation and implementation of alternate paint stripping methods which will minimize or eliminate hazardous waste and provide a safe operating environment. Alternate paint removal methods under investigation by the Navy at the present time include use of non-hazardous chemical paint removers, xenon flashlamp/CO2 pellets, lasers and plastic media. Plastic media blasting represents a mature technology in current usage for aircraft paint stripping and is being investigated for determination of its effects on Navy composite aircraft configurations.

Large-scale quantitative analysis of painting arts.

PubMed

Kim, Daniel; Son, Seung-Woo; Jeong, Hawoong

2014-12-11

Scientists have made efforts to understand the beauty of painting art in their own languages. As digital image acquisition of painting arts has made rapid progress, researchers have come to a point where it is possible to perform statistical analysis of a large-scale database of artistic paints to make a bridge between art and science. Using digital image processing techniques, we investigate three quantitative measures of images - the usage of individual colors, the variety of colors, and the roughness of the brightness. We found a difference in color usage between classical paintings and photographs, and a significantly low color variety of the medieval period. Interestingly, moreover, the increment of roughness exponent as painting techniques such as chiaroscuro and sfumato have advanced is consistent with historical circumstances.

Analysis of several Boolean operation based trajectory generation strategies for automotive spray applications

NASA Astrophysics Data System (ADS)

Gao, Guoyou; Jiang, Chunsheng; Chen, Tao; Hui, Chun

2018-05-01

Industrial robots are widely used in various processes of surface manufacturing, such as thermal spraying. The established robot programming methods are highly time-consuming and not accurate enough to fulfil the demands of the actual market. There are many off-line programming methods developed to reduce the robot programming effort. This work introduces the principle of several based robot trajectory generation strategy on planar surface and curved surface. Since the off-line programming software is widely used and thus facilitates the robot programming efforts and improves the accuracy of robot trajectory, the analysis of this work is based on the second development of off-line programming software Robot studio™. To meet the requirements of automotive paint industry, this kind of software extension helps provide special functions according to the users defined operation parameters. The presented planning strategy generates the robot trajectory by moving an orthogonal surface according to the information of coating surface, a series of intersection curves are then employed to generate the trajectory points. The simulation results show that the path curve created with this method is successive and smooth, which corresponds to the requirements of automotive spray industrial applications.

40 CFR Table 4 to Subpart Xxxx of... - Operating Limits for Puncture Sealant Application Control Devices

Code of Federal Regulations, 2011 CFR

2011-07-01

... performance test. 2. Carbon adsorber (regenerative) to which puncture sealant application spray booth emissions are ducted a. Maintain the total regeneration mass, volumetric flow, and carbon bed temperature at the operating range established during the performance test.b. Reestablish the carbon bed temperature...

24 CFR 570.608 - Lead-based paint.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Lead-based paint. 570.608 Section... DEVELOPMENT COMMUNITY FACILITIES COMMUNITY DEVELOPMENT BLOCK GRANTS Other Program Requirements § 570.608 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead...

24 CFR 570.608 - Lead-based paint.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 3 2012-04-01 2012-04-01 false Lead-based paint. 570.608 Section... DEVELOPMENT COMMUNITY FACILITIES COMMUNITY DEVELOPMENT BLOCK GRANTS Other Program Requirements § 570.608 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead...

24 CFR 570.608 - Lead-based paint.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 3 2013-04-01 2013-04-01 false Lead-based paint. 570.608 Section... DEVELOPMENT COMMUNITY FACILITIES COMMUNITY DEVELOPMENT BLOCK GRANTS Other Program Requirements § 570.608 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead...

24 CFR 570.608 - Lead-based paint.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 3 2014-04-01 2013-04-01 true Lead-based paint. 570.608 Section... DEVELOPMENT COMMUNITY FACILITIES COMMUNITY DEVELOPMENT BLOCK GRANTS Other Program Requirements § 570.608 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead...

24 CFR 570.608 - Lead-based paint.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 3 2010-04-01 2010-04-01 false Lead-based paint. 570.608 Section... DEVELOPMENT COMMUNITY FACILITIES COMMUNITY DEVELOPMENT BLOCK GRANTS Other Program Requirements § 570.608 Lead-based paint. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead...

But when was it painted?

NASA Astrophysics Data System (ADS)

Lundstad, E.; Woll, G.

2009-04-01

The Munch Museum, Oslo, Norway, is dedicated to the visual works of the famous Norwegian painter Edvard Munch (1863 - 1944). Edvard Munch was a symbolist, expressionist painter and printmaker from Oslo, Norway. He was regarded as the pioneer of the amazing Expressionist movement. His art work from the late 1800's is the most well known, but his later work is gradually attracting more attention and is quite an inspiration of many of today's artists. The Munch Museum catalogue for 2008 contains about 1700 paintings of which virtually very few have a precise date. Even when the artist has written the year on the painting itself, there may be a significant uncertainty about this date, and partly due to unclear writing making it difficult to interpret the numbers. This means that other sources need to be applied to verify an accurate date. The climatologist at the Norwegian Meteorological Institute can help dating paintings of Munch. E. g. the painting "Standing Woman with Arms Folded". The painting shows a woman in front of a hill with much snow. The location is almost certainty Grimsrød on Jeløya, a property Munch began renting on March 1, 1913. Jeløya is an island at the southeastcoast of Norway near the town Moss. Jeløya has usually not so much snow because it is near by the sea and windy. The last digit in the date is unclear and has been read as both '3' and '5'. The woman in the portrait, Ingeborg Kaurin, was Munch's model up to the beginning of 1915, so both dates are possible. The year written on the painting has been read as both 1913 and 1915, and since 1974 it has usually been interpreted as 1913 (Stenersensamlingen's catalogue 1974). In the project "But when was it painted?" disclose that it could be another year. One way to reconsider when a painting was painted is to study geophysical characteristics and consider historical observations of snow. The method that is used here is to study daily meteorological snow data from this period from the

Occupational risk assessment of paint industry workers

PubMed Central

de Oliveira, Hugo M.; Dagostim, Gracilene P.; da Silva, Arielle Mota; Tavares, Priscila; da Rosa, Luiz A. Z. C.; de Andrade, Vanessa M.

2011-01-01

Background: Thousands of chemical compounds are used in paint products, like pigments, extenders, binders, additives, and solvents (toluene, xylene, ketones, alcohols, esters, and glycol ethers). Paint manufacture workers are potentially exposed to the chemicals present in paint products although the patterns and levels of exposure to individual agents may differ from those of painters. The aim of the present study was to evaluate genome damage induced in peripheral blood lymphocytes and oral mucosa cells of paint industry workers. Materials and Methods: Genotoxicity was evaluated using the alkaline Comet assay in blood lymphocytes and oral mucosa cells, and the Micronucleus test in oral mucosa cells. For the micronucleus test in exfoliated buccal cells, no significant difference was detected between the control and paint industry workers. Results: The Comet assay in epithelia buccal cells showed that the damage index (DI) and damage frequency (DF) observed in the exposed group were significantly higher relative to the control group (P≤0.05). In the same way, the Comet assay data in peripheral blood leukocytes showed that both analysis parameters (DI and DF) were significantly greater than that for the control group (P≤0.05). Conclusions: Chronic occupational exposure to paints may lead to a slightly increased risk of genetic damage among paint industry workers. PMID:22223950

13 CFR 120.173 - Lead-based paint.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 13 Business Credit and Assistance 1 2014-01-01 2014-01-01 false Lead-based paint. 120.173 Section... to All Business Loans Requirements Imposed Under Other Laws and Orders § 120.173 Lead-based paint. If loan proceeds are for the construction or rehabilitation of a residential structure, lead-based paint...

13 CFR 120.173 - Lead-based paint.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 13 Business Credit and Assistance 1 2012-01-01 2012-01-01 false Lead-based paint. 120.173 Section... to All Business Loans Requirements Imposed Under Other Laws and Orders § 120.173 Lead-based paint. If loan proceeds are for the construction or rehabilitation of a residential structure, lead-based paint...

13 CFR 120.173 - Lead-based paint.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 13 Business Credit and Assistance 1 2011-01-01 2011-01-01 false Lead-based paint. 120.173 Section... to All Business Loans Requirements Imposed Under Other Laws and Orders § 120.173 Lead-based paint. If loan proceeds are for the construction or rehabilitation of a residential structure, lead-based paint...

13 CFR 120.173 - Lead-based paint.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 13 Business Credit and Assistance 1 2013-01-01 2013-01-01 false Lead-based paint. 120.173 Section... to All Business Loans Requirements Imposed Under Other Laws and Orders § 120.173 Lead-based paint. If loan proceeds are for the construction or rehabilitation of a residential structure, lead-based paint...

Large-Scale Quantitative Analysis of Painting Arts

PubMed Central

Kim, Daniel; Son, Seung-Woo; Jeong, Hawoong

2014-01-01

Scientists have made efforts to understand the beauty of painting art in their own languages. As digital image acquisition of painting arts has made rapid progress, researchers have come to a point where it is possible to perform statistical analysis of a large-scale database of artistic paints to make a bridge between art and science. Using digital image processing techniques, we investigate three quantitative measures of images – the usage of individual colors, the variety of colors, and the roughness of the brightness. We found a difference in color usage between classical paintings and photographs, and a significantly low color variety of the medieval period. Interestingly, moreover, the increment of roughness exponent as painting techniques such as chiaroscuro and sfumato have advanced is consistent with historical circumstances. PMID:25501877

Exposure of spray-men to dieldrin in residual spraying

PubMed Central

Fletcher, T. E.; Press, J. M.; Wilson, D. Bagster

1959-01-01

A study of the exposure of spray-men to dieldrin was made in a pilot scheme of residual spraying in the Taveta-Pare area of East Africa. A detailed work study was completed on the operators, and sources of contamination were enumerated. Filter paper pads were placed on the skin and outside clothing and the pick-up was estimated chemically. A spray-man, while using the daily average of 2.12 kg (4.7 pounds) of dieldrin and observing the protective measures laid down, received a dermal exposure of 1.8 mg of dieldrin per kg of body-weight per day. This was possibly reduced somewhat by washing with soap and water upon completion of each day's work. The sixteen spray-men and assistants were exposed for 180 days per year and there was an interim period of 2 months between spray cycles. No clinical symptoms of poisoning were observed. Comparison is made with certain programmes where dieldrin poisoning has occurred. Attention is drawn to the reduced time of exposure in the Taveta-Pare scheme, personal washing, the great value of protective clothing and of its daily washing in soap and water and the need to use a dilute suspension of wettable powder for spraying. Imagesp16-a PMID:13638786

Blanching of paint and varnish layers in easel paintings: contribution to the understanding of the alteration

NASA Astrophysics Data System (ADS)

Genty-Vincent, Anaïs; Eveno, Myriam; Nowik, Witold; Bastian, Gilles; Ravaud, Elisabeth; Cabillic, Isabelle; Uziel, Jacques; Lubin-Germain, Nadège; Menu, Michel

2015-11-01

The blanching of easel paintings can affect the varnish layer and also the paint layer with a blurring effect. The understanding of the physicochemical and optical phenomena involved in the whitening process remains an important challenge for the painting conservation. A set of ca. 50 microsamples from French, Flemish, and Italian blanched oil paintings, from sixteenth to nineteenth century, have been collected for in deep investigations. In parallel, the reproduction of the alteration was achieved by preparing some paint layers according to historical treatises and altering them in a climatic chamber in a humid environment or directly by immersing in ultrapure water. The observation of raw samples with a field-emission gun scanning electron microscope revealed for the first time that the altered layers have an unexpected highly porous structure with a pore size ranging from ca. 40 nm to 2 μm. The formation mechanism of these pores should mostly be physical as the supplementary analyses (Fourier transform infrared spectroscopy, gas chromatography-mass spectrometry) do not reveal any noticeable molecular modification. Considering the tiny size of the pores, the alteration can be explained by the Rayleigh or Mie light scattering.

24 CFR 92.355 - Lead-based paint.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

24 CFR 92.355 - Lead-based paint.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

24 CFR 92.355 - Lead-based paint.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

24 CFR 92.355 - Lead-based paint.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

24 CFR 92.355 - Lead-based paint.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Lead-based paint. 92.355 Section 92... HOME INVESTMENT PARTNERSHIPS PROGRAM Other Federal Requirements § 92.355 Lead-based paint. Housing assisted with HOME funds is subject to the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846...

VAB Flag Painting

NASA Image and Video Library

2002-01-01

On platforms suspended from the top of the 525-foot-high VAB, workers use rollers and brushes to repaint the U.S. flag on the southwest side of the Vehicle Assembly Building. The flag spans an area 209 feet by 110 feet, or about 23, 437 square feet. Each stripe is 9 feet wide and each star is 6 feet in diameter. The logo is also being painted. Known as the "meatball," the logo measures 110 feet by 132 feet, or about 12,300 square feet. The flag and logo were last painted in 1998, honoring NASA's 40th anniversary.

What You Should Know about Using Paint Strippers

MedlinePlus

... consumers are choosing to complete do-it-yourself (DIY) projects in their homes. Using paint strippers in ... chance of flammable paint stripper fumes catching fire. DIY use of methylene chloride-based paint strippers has ...

Effects of nozzle type and spray angle on spray deposition in ivy pot plants.

PubMed

Foqué, Dieter; Nuyttens, David

2011-02-01

Fewer plant protection products are now authorised for use in ornamental growings. Frequent spraying with the same product or a suboptimal technique can lead to resistance in pests and diseases. Better application techniques could improve the sustainable use of the plant protection products still available. Spray boom systems--instead of the still predominantly used spray guns--might improve crop protection management in greenhouses considerably. The effect of nozzle type, spray pressure and spray angle on spray deposition and coverage in ivy pot plants was studied, with a focus on crop penetration and spraying the bottom side of the leaves in this dense crop. The experiments showed a significant and important effect of collector position on deposition and coverage in the plant. Although spray deposition and coverage on the bottom side of the leaves are generally low, they could be improved 3.0-4.9-fold using the appropriate application technique. When using a spray boom in a dense crop, the nozzle choice, spray pressure and spray angle should be well considered. The hollow-cone, the air-inclusion flat-fan and the standard flat-fan nozzle with an inclined spray angle performed best because of the effect of swirling droplets, droplets with a high momentum and droplet direction respectively. Copyright © 2010 Society of Chemical Industry.

Exposures in the painting trades and paint manufacturing industry and risk of cancer among men and women in Sweden.

PubMed

Brown, Linda Morris; Moradi, Tahereh; Gridley, Gloria; Plato, Nils; Dosemeci, Mustafa; Fraumeni, Joseph F

2002-03-01

Using data from the 1960 and 1970 Swedish censuses and the Swedish Cancer Register for 1971 to 1989, this study investigated variations in cancer risk by gender associated with employment in painting trades and paint manufacturing. Among men, standardized incidence ratios were significantly increased for lung cancer among painters and lacquerers; bladder cancer among artists; and pancreas cancer, lung cancer, and nonlymphocytic leukemia among paint and varnish plant workers. Risks for women were elevated for cancers of the esophagus, larynx, and oral cavity among lacquerers and for oral cancer among glaziers. These findings are consistent with the report of the International Agency for Research on Cancer that classified painting as an occupationally related cause of cancer and provide further evidence that the risk of certain cancers is increased by exposures in the paint manufacturing process.

Bringing Art to Life through Living Paintings

ERIC Educational Resources Information Center

Stillwagon, Joanne

2005-01-01

In this article, the author relates how she and other art teachers developed a "living painting" lesson, an art lesson that incorporates art history and painting. The lesson was developed also in part to help new student-teachers plan a memorable lesson. With the living painting lesson, students will have to choose and recreate famous paintings…

Enhanced multifunctional paint for detection of radiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, Joseph C.; Moses, Edward Ira; Rubenchik, Alexander M.

An enhanced multifunctional paint apparatus, systems, and methods for detecting radiation on a surface include providing scintillation particles; providing an enhance neutron absorptive material; providing a binder; combining the scintillation particles, the enhance neutron absorptive material, and the binder creating a multifunctional paint; applying the multifunctional paint to the surface; and monitoring the surface for detecting radiation.

Nanoindentation and the micromechanics of Van Gogh oil paints

NASA Astrophysics Data System (ADS)

Salvant, Johanna; Barthel, Etienne; Menu, Michel

2011-08-01

Understanding the mechanical properties of ancient paintings is a major issue for conservation and restoration. One strategy is to measure the mechanical properties of reconstructed paints: however, the aging process is poorly known, so it is also desirable to measure mechanical properties directly on ancient paint samples. Using nanoindentation, we have characterized submillimetric samples recovered from restoration of two Van Gogh paintings and compared the results with reconstructed paint samples. We demonstrate that the reduced modulus and hardness of historical paints can be measured at a very local scale, even differentiating between each paint layer. Our reconstructed paint samples exhibit elastic moduli comparable to values of the literature, but the values measured on the two 19th century paint samples are found to be significantly larger. Similarly, the compositional dependence of the elastic modulus is consistent with literature results for our reconstructed samples while our preliminary results for ancient samples do not readily fall into the same pattern. These results all point out to a significant impact of long term aging, in a manner which is difficult to predict in our present state of understanding. They demonstrate that nanoindentation is a very adequate tool to improve our knowledge of art paint mechanics and aging.

Assessment of HIV related risky behaviour: a comparative study of face-to-face interviews and Polling Booth Surveys in the general population of Cotonou, Benin

PubMed Central

BÉHANZIN, Luc; DIABATÉ, Souleymane; MINANI, Isaac; LOWNDES, Catherine M.; BOILY, Marie-Claude; LABBÉ, Annie-Claude; ANAGONOU, Séverin; ZANNOU, Djimon Marcel; BUVÉ, Anne; ALARY, Michel

2013-01-01

Objectives During the 2008 HIV prevalence survey carried out in the general population of Cotonou, Benin, face-to-face interviews (FTFI) were used to assess risky behaviours for HIV and other sexually transmitted infections (STI). We compared sexual behaviours reported in FTFI with those reported in polling booth surveys (PBS) carried out in parallel in an independent random sample of the same population. Methods In PBS, respondents grouped by gender and marital status answered simple questions by putting tokens with question numbers in a green box (affirmative answers) or a red box (negative answers). Both boxes were placed inside a private booth. For each group and question, data were gathered together by type of answer. The structured and gender-specific FTFI guided by trained interviewers included all questions asked during the PBS.. Pearson chi-square or Fisher’s exact test were used to compare FTFI and PBS according to affirmative answers. Results Overall, respondents reported more stigmatized behaviours in PBS than in FTFI: the proportions of both married women and men who reported ever having had commercial sex were 17.4% and 41.6% in PBS versus 1.8% and 19.6% in FTFI, respectively. The corresponding proportions among unmarried women and men were 16.1% and 25.5% in PBS versus 3.9% and 13.0% in FTFI, respectively. The proportion of married women who reported having had extramarital sex since marriage was 23.6% in PBS versus 4.6% in FTFI. Conclusion Polling booth surveys are suitable to monitor reliable HIV/STI risk behaviours. Their use should be expanded in behavioural surveillance. PMID:23723251

Examination of lead concentrations in new decorative enamel paints in four countries with different histories of activity in lead paint regulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, C. Scott, E-mail: clarkcs@ucmail.uc.edu; International POPS Elimination Network; Kumar, Abhay

Paints with high lead concentrations (ppm) continue to be sold around the world in many developing countries and those with economies in transition representing a major preventable environmental health hazard that is being increased as the economies expand and paint consumption is increasing. Prior lead paint testing had been performed in Brazil and India and these countries were selected to examine the impact of a new regulatory limit in Brazil and the impact of efforts of non-governmental organizations and others to stop the use of lead compounds in manufacturing paints. Armenia and Kazakhstan, in Central Asia, were selected because nomore » information on lead concentration in those regions was available, no regulatory activities were evident and non-governmental organizations in the IPEN network were available to participate. Another objective of this research was to evaluate the lead loading (µg/cm{sup 2}) limit determined by X-Ray Fluorescence (XRF) for areas on toys that are too small to obtain a sample of sufficient size for laboratory analysis. The lead concentrations in more than three-fourths of the paints from Armenia and Kazakhstan exceeded 90 ppm, the limit in the United States, and 600 ppm, the limit in Brazil. The percentages were about one-half as high in Brazil and India. The average concentration in paints purchased in Armenia, 25,000 ppm, is among the highest that has been previously reported, that in Kazakhstan, 15,700 ppm, and India, 16,600, about median. The average concentration in Brazil, 5600 ppm, is among the lowest observed. Paints in Brazil that contained an average of 36,000 ppm before the regulatory limit became effective were below detection (<9 ppm) in samples collected in the current study. The lack of any apparent public monitoring of paint lead content as part of regulatory enforcement makes it difficult to determine whether the regulation was a major factor contributing to the decline in lead use in these paints. Using data

24 CFR 965.701 - Lead-based paint poisoning prevention.

Code of Federal Regulations, 2010 CFR

2010-04-01

... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Lead-based paint poisoning...

24 CFR 965.701 - Lead-based paint poisoning prevention.

Code of Federal Regulations, 2014 CFR

2014-04-01

... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Lead-based paint poisoning...

24 CFR 965.701 - Lead-based paint poisoning prevention.

Code of Federal Regulations, 2012 CFR

2012-04-01

... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Lead-based paint poisoning...

24 CFR 965.701 - Lead-based paint poisoning prevention.

Code of Federal Regulations, 2011 CFR

2011-04-01

... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Lead-based paint poisoning...

24 CFR 965.701 - Lead-based paint poisoning prevention.

Code of Federal Regulations, 2013 CFR

2013-04-01

... URBAN DEVELOPMENT PHA-OWNED OR LEASED PROJECTS-GENERAL PROVISIONS Lead-Based Paint Poisoning Prevention § 965.701 Lead-based paint poisoning prevention. The requirements of the Lead-Based Paint Poisoning... 24 Housing and Urban Development 4 2013-04-01 2013-04-01 false Lead-based paint poisoning...

Evaluation of interior and exterior latex paints : final report.

DOT National Transportation Integrated Search

1979-10-01

The wood panels that have only one coat of paint over bare wood and one coat of paint over primed wood are continuing to show sighs of deterioration. The wood panels that have two coats of paint over bare wood and two coats of paint over primed wood ...

24 CFR 35.135 - Use of paint containing lead.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Use of paint containing lead. 35...

24 CFR 35.135 - Use of paint containing lead.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Use of paint containing lead. 35...

24 CFR 35.135 - Use of paint containing lead.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Use of paint containing lead. 35...

24 CFR 35.135 - Use of paint containing lead.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Use of paint containing lead. 35...

24 CFR 35.135 - Use of paint containing lead.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES General Lead-Based Paint Requirements and Definitions for All Programs. § 35.135 Use of paint containing lead. (a... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Use of paint containing lead. 35...

Sensory and analytical evaluations of paints with and without texanol.

PubMed

Gallagher, Michelle; Dalton, Pamela; Sitvarin, Laura; Preti, George

2008-01-01

Perception of odor can figure prominently in complaints about indoor air,yet identification of the responsible compound(s) is often difficult. For example, paint emissions contain a variety of odorous volatile organic compounds (VOCs) which maytrigger reports of irritation and upper respiratory health effects. Texanol ester alcohol (2,2,4-trimethyl-1,3-pentanediol monoisobutyrate), a paint coalescing agent, is frequently associated with the "persistent, characteristic odor" of water-based paint. To evaluate the sensory impact of Texanol, naive (unfamiliar with paint constituents) and experienced (familiar with paint constituents) subjects evaluated the odor properties of paints with and without Texanol. VOC emissions from neat paint and paint applied to gypsum wallboard were collected via solid-phase microextraction and analyzed by gas chromatography/ mass spectrometry and gas chromatography/olfactometry. Regardless of subjects' prior experience, aromatic hydrocarbons and oxygenated compounds, introduced from other paint additives and not Texanol, were most commonly associated with paint odor. However, quantitative sensory techniques demonstrated that addition of Texanol to paints led to an overall increase in the perceived intensity of the coating. The combined use of these techniques proved to be an effective methodology for analyzing the structure of paint volatiles and their sensory properties and holds promise for solving many odorous indoor air problems.

Spray nozzle investigation for the Improved Helicopter Icing Spray System (IHISS)

NASA Technical Reports Server (NTRS)

Peterson, Andrew A.; Oldenburg, John R.

1990-01-01

A contract has been awarded by the U.S. Army to design, fabricate and test a replacement for the existing Helicopter Icing Spray System. Data are shown for extensive bench and icing tunnel test programs used to select and modify an improved spray nozzle. The IHISS, capable of deployment from any CH-47 helicopter, will include new icing spray nozzles and pneumatic pressure source, and a significantly larger water tank and spray boom. The resulting system will provide a significantly larger icing cloud with droplet characteristics closely matching natural icing conditions.

EVALUATION OF LOW-VOC LATEX PAINTS

EPA Science Inventory

The paper gives results of an evaluation of four commercially available low-VOC (volatile organic compound) latex paints as substitutes for conventional latex paints by assessing both their emission characteristics and their performance as coatings. Bulk analysis indicated that ...

A Five-year Performance Study of Low VOC Coatings over Zinc Thermal Spray for the Protection of Carbon Steel at the Kennedy Space Center

NASA Technical Reports Server (NTRS)

Kolody, Mark R.; Curran, Jerome P.; Calle, Luz Marina

2014-01-01

The launch facilities at the Kennedy Space Center (KSC) are located approximately 1000 feet from the Atlantic Ocean where they are exposed to salt deposits, high humidity, high UV degradation, and acidic exhaust from solid rocket boosters. These assets are constructed from carbon steel, which requires a suitable coating to provide long-term protection to reduce corrosion and its associated costs. While currently used coating systems provide excellent corrosion control performance, they are subject to occupational, safety, and environmental regulations at the Federal and State levels that limit their use. Many contain high volatile organic compounds (VOCs), hazardous air pollutants, and other hazardous materials. Hazardous waste from coating operations include vacuum filters, zinc dust, hazardous paint related material, and solid paint. There are also worker safety issues such as exposure to solvents and isocyanates. To address these issues, top-coated thermal spray zinc coating systems were investigated as a promising environmentally friendly corrosion protection for carbon steel in an acidic launch environment. Additional benefits of the combined coating system include a long service life, cathodic protection to the substrate, no volatile contaminants, and high service temperatures. This paper reports the results of a performance based study to evaluate low VOC topcoats (for thermal spray zinc coatings) on carbon steel for use in a space launch environment.

Inadvertent Polychlorinated Biphenyls in Commercial Paint Pigments†

PubMed Central

2009-01-01

A polychlorinated biphenyl (PCB) that was not produced as part of the Aroclor mixtures banned in the 1980s was recently reported in air samples collected in Chicago, Philadelphia, the Arctic, and several sites around the Great Lakes. In Chicago, the congener 3,3′-dichlorobiphenyl or PCB11 was found to be the fifth most concentrated congener and ubiquitous throughout the city. The congener exhibited strong seasonal concentration trends that suggest volatilization of this compound from common outdoor surfaces. Due to these findings and also the compound’s presence in waters that received waste from paint manufacturing facilities, we hypothesized that PCB11 may be present in current commercial paint. In this study we measured PCBs in paint sold on the current retail market. We tested 33 commercial paint pigments purchased from three local paint stores. The pigment samples were analyzed for all 209 PCB congeners using gas chromatography with tandem mass spectrometry (GC-MS/MS). More than 50 PCB congeners including several dioxin-like PCBs were detected, and the PCB profiles varied due to different types of pigments and different manufacturing processes. PCB congeners were detected in azo and phthalocyanine pigments which are commonly used in paint but also in inks, textiles, paper, cosmetics, leather, plastics, food and other materials. Our findings suggest several possible mechanisms for the inadvertent production of specific PCB congeners during the manufacturing of paint pigments. PMID:19957996

Combustion of liquid paint wastes in fluidized bed boiler as element of waste management system in the paint factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soko, W.A.; Biaecka, B.

1998-12-31

In this paper the solution to waste problems in the paint industry is presented by describing their combustion in a fluidized bed boiler as a part of the waste management system in the paint factory. Based on the Cleaner Production idea and concept of integration of design process with a future exploitation of equipment, some modifications of the waste management scheme in the factory are discussed to reduce the quantity of toxic wastes. To verify this concept combustion tests of paint production wastes and cocombustion of paint wastes with coal in an adopted industrial boiler were done. Results of thesemore » tests are presented in the paper.« less

Pattern Recognition-Assisted Infrared Library Searching of the Paint Data Query Database to Enhance Lead Information from Automotive Paint Trace Evidence.

PubMed

Lavine, Barry K; White, Collin G; Allen, Matthew D; Weakley, Andrew

2017-03-01

Multilayered automotive paint fragments, which are one of the most complex materials encountered in the forensic science laboratory, provide crucial links in criminal investigations and prosecutions. To determine the origin of these paint fragments, forensic automotive paint examiners have turned to the paint data query (PDQ) database, which allows the forensic examiner to compare the layer sequence and color, texture, and composition of the sample to paint systems of the original equipment manufacturer (OEM). However, modern automotive paints have a thin color coat and this layer on a microscopic fragment is often too thin to obtain accurate chemical and topcoat color information. A search engine has been developed for the infrared (IR) spectral libraries of the PDQ database in an effort to improve discrimination capability and permit quantification of discrimination power for OEM automotive paint comparisons. The similarity of IR spectra of the corresponding layers of various records for original finishes in the PDQ database often results in poor discrimination using commercial library search algorithms. A pattern recognition approach employing pre-filters and a cross-correlation library search algorithm that performs both a forward and backward search has been used to significantly improve the discrimination of IR spectra in the PDQ database and thus improve the accuracy of the search. This improvement permits inter-comparison of OEM automotive paint layer systems using the IR spectra alone. Such information can serve to quantify the discrimination power of the original automotive paint encountered in casework and further efforts to succinctly communicate trace evidence to the courts.

47 CFR 25.286 - Antenna painting and lighting.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Antenna painting and lighting. 25.286 Section... SATELLITE COMMUNICATIONS Technical Operations § 25.286 Antenna painting and lighting. The owner of an earth station antenna structure must comply with all applicable painting, marking, and/or lighting requirements...

Painting a Data-Rich Picture

ERIC Educational Resources Information Center

Earl, Lorna; Katz, Steven

2005-01-01

Using data for school reform is like painting a series of pictures--pictures that are subtle and capture the nuances of the subject. This is a far cry from drawing stick figures or paint-by-numbers. Imagine the experiences of the French painter Claude Monet as he wandered through his garden at Giverny at different times of the day and year,…

76 FR 27044 - Lead-Based Paint Renovation, Repair and Painting, and Pre-Renovation Education Activities in...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-10

..., Repair and Painting, and Pre- Renovation Education Activities in Target Housing and Child Occupied...), and a lead-based paint pre-renovation education program in accordance with section 406(b) of TSCA, 15... renovation and remodeling activities of pre-1978 housing and child-occupied facilities in the State of...

Painting with polygons: a procedural watercolor engine.

PubMed

DiVerdi, Stephen; Krishnaswamy, Aravind; Měch, Radomír; Ito, Daichi

2013-05-01

Existing natural media painting simulations have produced high-quality results, but have required powerful compute hardware and have been limited to screen resolutions. Digital artists would like to be able to use watercolor-like painting tools, but at print resolutions and on lower end hardware such as laptops or even slates. We present a procedural algorithm for generating watercolor-like dynamic paint behaviors in a lightweight manner. Our goal is not to exactly duplicate watercolor painting, but to create a range of dynamic behaviors that allow users to achieve a similar style of process and result, while at the same time having a unique character of its own. Our stroke representation is vector based, allowing for rendering at arbitrary resolutions, and our procedural pigment advection algorithm is fast enough to support painting on slate devices. We demonstrate our technique in a commercially available slate application used by professional artists. Finally, we present a detailed analysis of the different vector-rendering technologies available.

Service-Learning General Chemistry: Lead Paint Analyses

NASA Astrophysics Data System (ADS)

Kesner, Laya; Eyring, Edward M.

1999-07-01

Houses painted with lead-based paints are ubiquitous in the United States because the houses and the paint have not worn out two decades after federal regulations prohibited inclusion of lead in paint. Remodeling older homes thus poses a health threat for infants and small children living in those homes. In a service-learning general chemistry class, students disseminate information about this health threat in an older neighborhood. At some of the homes they collect paint samples that they analyze for lead both qualitatively and quantitatively. This service-learning experience generates enthusiasm for general chemistry through the process of working on a "real" problem. Sample collection familiarizes the students with the concept of "representative" sampling. The sample preparation for atomic absorption spectroscopic (AAS) analysis enhances their laboratory skills. The focus of this paper is on the mechanics of integrating this particular service project into the first-term of the normal general chemistry course.

Spray drift reduction evaluations of spray nozzles using a standardized testing protocol

USDA-ARS?s Scientific Manuscript database

The development and testing of drift reduction technologies has come to the forefront of application research in the past few years in the United States. Drift reduction technologies (DRTs) can be spray nozzles, sprayer modifications, spray delivery assistance, spray property modifiers (adjuvants),...

A Short History of the Chemistry of Painting.

ERIC Educational Resources Information Center

Friedstein, Harriet G.

1981-01-01

Includes information on: (1) relationship of art and science; (2) paintings' early history; (3) Egyptian, Greek, Chinese, Byzantine, and Medieval painting; (4) chemical analysis of pigments; (5) chemistry of early pigments; and (6) paint media. Tabular data are provided on chemical names for artists' pigments with their earliest known dates. (CS)

Nonflammable organic-base paint for oxygen-rich atmospheres

NASA Technical Reports Server (NTRS)

Harwell, R. J.; Key, C. F.; Krupnick, A. C.

1971-01-01

New paint formulations, which combine aqueous latex paints with inorganic pigments and additives, produce coatings that are self-extinguishing in pure oxygen at pressures up to twice the partial pressure of atmospheric oxygen. A paint formulation in percent by weight is given and the properties of resultant coatings are discussed.

7 CFR 3201.71 - Interior paints and coatings.

Code of Federal Regulations, 2014 CFR

2014-01-01

... procurement applies are: (i) Interior latex and waterborne alkyd paints and coatings. (ii) Interior oil-based...) Interior latex and waterborne alkyd paints and coatings—20 percent. (2) Interior oil-based and solventborne... 7 Agriculture 15 2014-01-01 2014-01-01 false Interior paints and coatings. 3201.71 Section 3201.71...

7 CFR 3201.71 - Interior paints and coatings.

Code of Federal Regulations, 2013 CFR

2013-01-01

... procurement applies are: (i) Interior latex and waterborne alkyd paints and coatings. (ii) Interior oil-based...) Interior latex and waterborne alkyd paints and coatings—20 percent. (2) Interior oil-based and solventborne... 7 Agriculture 15 2013-01-01 2013-01-01 false Interior paints and coatings. 3201.71 Section 3201.71...

7 CFR 3201.71 - Interior paints and coatings.

Code of Federal Regulations, 2012 CFR

2012-01-01

... procurement applies are: (i) Interior latex and waterborne alkyd paints and coatings. (ii) Interior oil-based...) Interior latex and waterborne alkyd paints and coatings—20 percent. (2) Interior oil-based and solventborne... 7 Agriculture 15 2012-01-01 2012-01-01 false Interior paints and coatings. 3201.71 Section 3201.71...

A qualitative study of student responses to body painting.

PubMed

Finn, Gabrielle M; McLachlan, John C

2010-01-01

One hundred and thirty-three preclinical medical students participated in 24 focus groups over the period 2007-2009 at Durham University. Focus groups were conducted to ascertain whether or not medical students found body painting anatomical structures to be an educationally beneficial learning activity. Data were analyzed using a grounded theory approach. Five principal themes emerged: (1) body painting as a fun learning activity, (2) body painting promoting retention of knowledge, (3) factors contributing to the memorability of body painting, (4) removal from comfort zone, and (5) the impact of body painting on students' future clinical practice. Students perceive body painting to be a fun learning activity, which aids their retention of the anatomical knowledge acquired during the session. Sensory factors, such as visual stimuli, especially color, and the tactile nature of the activity, promote recall. Students' preference for painting a peer or being painted is often dependent upon their learning style, but there are educational benefits for both roles. The moderate amounts of undressing involved encouraging students to consider issues surrounding body image; this informs their attitudes towards future patients. Body painting is a useful adjunct to traditional anatomy and clinical skills teaching. The fun element involved in the delivery of this teaching defuses the often formal academic context, which in turn promotes a positive learning environment. Copyright 2009 American Association of Anatomists.

24 CFR 891.325 - Lead-based paint requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

24 CFR 891.325 - Lead-based paint requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 4 2013-04-01 2013-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

24 CFR 891.325 - Lead-based paint requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

24 CFR 891.325 - Lead-based paint requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

24 CFR 891.325 - Lead-based paint requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Lead-based paint requirements. 891... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based...

Plasma Sprayed Hydroxyapatite Coatings: Influence of Spraying Power on Microstructure

NASA Astrophysics Data System (ADS)

Mohd, S. M.; Abd, M. Z.; Abd, A. N.

2010-03-01

The plasma sprayed hydroxyapatite (HA) coatings are used on metallic implants to enhance the bonding between the implant and bone in human body. The coating process was implemented at different spraying power for each spraying condition. The coatings formed from a rapid solidification of molten and partly molten particles that impact on the surface of substrate at high velocity and high temperature. The study was concentrated on different spraying power that is between 23 to 31 kW. The effect of different power on the coatings microstructure was investigated using scanning electron microscope (SEM) and phase composition was evaluated using X-ray diffraction (XRD) analysis. The coatings surface morphology showed distribution of molten, partially melted particles and some micro-cracks. The produced coatings were found to be porous as observed from the cross-sectional morphology. The coatings XRD results indicated the presence of crystalline phase of HA and each of the patterns was similar to the initial powder. Regardless of different spraying power, all the coatings were having similar XRD patterns.

Slurry spray distribution within a simulated laboratory scale spray dryer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bertone, P.C.

1979-12-20

It was found that the distribution of liquid striking the sides of a simulated room temperature spray dryer was not significantly altered by the choice of nozles, nor by a variation in nozzle operating conditions. Instead, it was found to be a function of the spray dryer's configuration. A cocurrent flow of air down the drying cylinder, not possible with PNL's closed top, favorably altered the spray distribution by both decreasing the amount of liquid striking the interior of the cylinder from 72 to 26% of the feed supplied, and by shifting the zone of maximum impact from 1.0 tomore » 1.7 feet from the nozzle. These findings led to the redesign of the laboratory scale spray dryer to be tested at the Savannah River Plant. The diameter of the drying chamber was increased from 5 to 8 inches, and a cocurrent flow of air was established with a closed recycle. Finally, this investigation suggested a drying scheme which offers all the advantages of spray drying without many of its limitations.« less

High-performance shape-engineerable thermoelectric painting

PubMed Central

Park, Sung Hoon; Jo, Seungki; Kwon, Beomjin; Kim, Fredrick; Ban, Hyeong Woo; Lee, Ji Eun; Gu, Da Hwi; Lee, Se Hwa; Hwang, Younghun; Kim, Jin-Sang; Hyun, Dow-Bin; Lee, Sukbin; Choi, Kyoung Jin; Jo, Wook; Son, Jae Sung

2016-01-01

Output power of thermoelectric generators depends on device engineering minimizing heat loss as well as inherent material properties. However, the device engineering has been largely neglected due to the limited flat or angular shape of devices. Considering that the surface of most heat sources where these planar devices are attached is curved, a considerable amount of heat loss is inevitable. To address this issue, here, we present the shape-engineerable thermoelectric painting, geometrically compatible to surfaces of any shape. We prepared Bi2Te3-based inorganic paints using the molecular Sb2Te3 chalcogenidometalate as a sintering aid for thermoelectric particles, with ZT values of 0.67 for n-type and 1.21 for p-type painted materials that compete the bulk values. Devices directly brush-painted onto curved surfaces produced the high output power of 4.0 mW cm−2. This approach paves the way to designing materials and devices that can be easily transferred to other applications. PMID:27834369

Infrared Thermography as a Non-destructive Testing Solution for Thermal Spray Metal Coatings

NASA Astrophysics Data System (ADS)

Santangelo, Paolo E.; Allesina, Giulio; Bolelli, Giovanni; Lusvarghi, Luca; Matikainen, Ville; Vuoristo, Petri

2017-12-01

In this work, an infrared (IR) thermographic procedure was evaluated as a non-destructive testing tool to detect damage in thermal spray metallic coatings. As model systems, polished HVOF- and HVAF-sprayed Fe-based layers deposited onto steel plates were employed. Damage by external-object impingement was simulated through a cyclic impact-test apparatus, which induced circumferential and radial cracks across all model systems, and interface cracks of different sizes in distinct samples. Damaged and undamaged plates were bulk-heated to above 100 °C using an IR lamp; their free-convection cooling was then recorded by an IR thermocamera. The intentionally induced defects were hardly detectable in IR thermograms, due to IR reflection and artificial "hot" spots induced by residuals of transfer material from the impacting counterbody. As a micrometer-thin layer of black paint was applied, surface emissivity got homogenized and any artifacts were effectively suppressed, so that failed coating areas clearly showed up as "cold spots." This effect was more apparent when large interface cracks occurred. Finite-element modeling proved the physical significance of the IR-thermography approach, showing that failed coating areas are cooled by surrounding air faster than they are heated by conduction from the hot substrate, which is due to the insulating effect of cracks.

29 CFR 1915.34 - Mechanical paint removers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... paints, preservatives, rusts, or other coatings by means of power tools shall be protected against eye...) All portable rotating tools used for the removal of paints, preservatives, rusts or other coatings...

29 CFR 1915.34 - Mechanical paint removers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... paints, preservatives, rusts, or other coatings by means of power tools shall be protected against eye...) All portable rotating tools used for the removal of paints, preservatives, rusts or other coatings...

29 CFR 1915.34 - Mechanical paint removers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... paints, preservatives, rusts, or other coatings by means of power tools shall be protected against eye...) All portable rotating tools used for the removal of paints, preservatives, rusts or other coatings...

29 CFR 1915.34 - Mechanical paint removers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... paints, preservatives, rusts, or other coatings by means of power tools shall be protected against eye...) All portable rotating tools used for the removal of paints, preservatives, rusts or other coatings...

40 CFR 63.4964 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

... operation are applied within the capture system; coating solvent flash-off and coating, curing, and drying... parts enter the open shop environment when being moved between a spray booth and a curing oven. (b... from the beginning to the end of production, which includes surface preparation activities and drying...

40 CFR 63.3965 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

...; coating solvent flash-off, curing, and drying occurs within the capture system; and the removal or... spray booth and a curing oven. (b) Measuring capture efficiency. If the capture system does not meet... surface preparation activities and drying and curing time. (c) Liquid-to-uncaptured-gas protocol using a...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 60.451 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-coated metal range, oven, microwave oven, refrigerator, freezer, washer, dryer, dishwasher, water heater... submerged in a tank filled with coating material suspended in water and an electrical potential is used to... is fused into a continuous coating film through the use of heat. Spray booth means the structure...

40 CFR 63.11444 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... pollution control device (APCD) means any equipment that reduces the quantity of a pollutant that is emitted to the air. Examples of APCD currently used on glaze spray booths include, but are not limited to...? 63.11444 Section 63.11444 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.11444 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... pollution control device (APCD) means any equipment that reduces the quantity of a pollutant that is emitted to the air. Examples of APCD currently used on glaze spray booths include, but are not limited to...? 63.11444 Section 63.11444 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.11444 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... pollution control device (APCD) means any equipment that reduces the quantity of a pollutant that is emitted to the air. Examples of APCD currently used on glaze spray booths include, but are not limited to...? 63.11444 Section 63.11444 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.11444 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... pollution control device (APCD) means any equipment that reduces the quantity of a pollutant that is emitted to the air. Examples of APCD currently used on glaze spray booths include, but are not limited to...? 63.11444 Section 63.11444 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.11444 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... pollution control device (APCD) means any equipment that reduces the quantity of a pollutant that is emitted to the air. Examples of APCD currently used on glaze spray booths include, but are not limited to...? 63.11444 Section 63.11444 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

40 CFR 63.11435 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Clay Ceramics Manufacturing Area Sources... if you own or operate a clay ceramics manufacturing facility (as defined in § 63.11444), with an atomized glaze spray booth or kiln that fires glazed ceramic ware, that processes more than 45 megagrams...

Difference in brain activations during appreciating paintings and photographic analogs

PubMed Central

Mizokami, Yoshinori; Terao, Takeshi; Hatano, Koji; Hoaki, Nobuhiko; Kohno, Kentaro; Araki, Yasuo; Kodama, Kensuke; Makino, Mayu; Izumi, Toshihiko; Shimomura, Tsuyoshi; Fujiki, Minoru; Kochiyama, Takanori

2014-01-01

Several studies have investigated neural correlates of aesthetic appreciation for paintings but to date the findings have been heterogeneous. This heterogeneity may be attributed to previous studies’ measurement of aesthetic appreciation of not only the beauty of paintings but also the beauty of motifs of the paintings. In order to better elucidate the beauty of paintings, it seems necessary to compare aesthetic appreciation of paintings and photographic analogs which included corresponding real images. We prepared for famous painters’ pictures and their photographic analogs which were set up to resemble each painting in order to investigate the hypothesis that there exist specific neural correlates associated with the aesthetic appreciation for paintings. Forty-four subjects participated in functional magnetic resonance study which required comparisons of aesthetic appreciation of paintings of still life and landscape versus photographic analogs including corresponding real images of still life and landscape. Bilateral cuneus and the left lingual gyrus were activated in the comparison of aesthetic appreciation of paintings versus photographic analogs. In conclusion, the present findings suggest a possibility of the existence of specific neural correlates associated with the aesthetic appreciation for paintings and that bilateral cuneus and the left lingual gyrus may be involved. PMID:25071508

Exposure Assessment Suggests Exposure to Lung Cancer Carcinogens in a Painter Working in an Automobile Bumper Shop

PubMed Central

Kim, Boowook; Yoon, Jin-Ha; Choi, Byung-Soon; Shin, Yong Chul

2013-01-01

A 46-year-old man who had worked as a bumper spray painter in an automobile body shop for 15 years developed lung cancer. The patient was a nonsmoker with no family history of lung cancer. To determine whether the cancer was related to his work environment, we assessed the level of exposure to carcinogens during spray painting, sanding, and heat treatment. The results showed that spray painting with yellow paint increased the concentration of hexavalent chromium in the air to as much as 118.33 μg/m3. Analysis of the paint bulk materials showed that hexavalent chromium was mostly found in the form of lead chromate. Interestingly, strontium chromate was also detected, and the concentration of strontium chromate increased in line with the brightness of the yellow color. Some paints contained about 1% crystalline silica in the form of quartz. PMID:24422178

Terahertz NDE for Under Paint Corrosion Detection and Evaluation

NASA Technical Reports Server (NTRS)

Anastasi, Robert F.; Madaras, Eric I.

2005-01-01

Corrosion under paint is not visible until it has caused paint to blister, crack, or chip. If corrosion is allowed to continue then structural problems may develop. Identifying corrosion before it becomes visible would minimize repairs and costs and potential structural problems. Terahertz NDE imaging under paint for corrosion is being examined as a method to inspect for corrosion by examining the terahertz response to paint thickness and to surface roughness.

75 FR 13127 - Lead-Based Paint Renovation, Repair and Painting Activities in Target Housing and Child Occupied...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-18

... ENVIRONMENTAL PROTECTION AGENCY [EPA-R07-OPPT-2010-0155; FRL-9128-4] Lead-Based Paint Renovation, Repair and Painting Activities in Target Housing and Child Occupied Facilities; State of Iowa. Notice of... target housing and child-occupied facilities: 1. Establish the discipline of lead-safe renovator. 2...

75 FR 51808 - Lead-Based Paint Renovation, Repair and Painting Activities in Target Housing and Child Occupied...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-23

... Renovation, Repair and Painting Activities in Target Housing and Child Occupied Facilities; State of Rhode.... These rules already cover all lead-based paint activities that are conducted in target housing and child... in target housing and child-occupied facilities. These rules: 1. Establish the discipline of lead...

A Hunt for Tennyson: Teaching Poetry through Painting.

ERIC Educational Resources Information Center

Lask-Spinac, Sabina

Tennyson's poem "The Lady of Shalott" and Holman Hunt's painting of the same subject are excellent examples of the value of exploring poetry through painting. One of the biggest questions raised in relation to the poem's theme is the problem of its ambiguity. By looking at the painting in class, one can sense the lack of definite…

Listening as a Basis for Painting.

ERIC Educational Resources Information Center

Kulianin, Anatoly F.

1980-01-01

The author, formerly a Soviet art teacher, describes his technique for combining music and painting. After teaching children the fundamentals of music technique and color, he has them experience a piece of music and paint their reactions. One of several articles in this issue on art teaching in other countries. (SJL)

Laser processing of metal surfaces for increasing paint adhesion

NASA Astrophysics Data System (ADS)

Hirose, Tomiyasu; Ichihara, Hideki; Sugimoto, Kenji; Sasazawa, Kazuo; Shibasaki, Shouji

2000-01-01

Painted metal exteriors of buildings begin to degrade in about 10 years due to solar heat, UV rays, the sea salt adhesion, the acid rain etc. When degradation and exfoliation of the paint film occurs, rust appears in the metal and replacement or repainting becomes necessary. The adhesion of paints on metal is usually achieved by chemical adhesion or by increasing the surface area by blast processing. In this study, the possibility of improving paint adhesion by forming minute holes on the metal surface by laser irradiation was studied through modeling of the adhesion of the paint film and adaptability to deformation. The viscosity and painting method depend on the size and location of the oles. The presence of the holes makes it possible to form complicated shapes by pressing because the holes absorb some of the strain caused by pressing.

Use of GC/MS Analysis to Distinguish Between Vapor Intrusion and Indoor Sources of VOCs - Standardized Protocol for On-Site Evaluation of Vapor Intrusion

DTIC Science & Technology

2014-07-01

Testing a Sealed Crack in a Concrete Floor .................................................................. 14 Figure 5: VOC Responses to...Engineered Fluid Toluene Some paints and adhesives SprayPAK Enamel , Minwax Wood Finish Xylenes Adhesives, paints, gasoline Bonide Tree Sprays and...expansion joints, plumbing penetrations, or cracks . 3 Note that if indoor air concentrations are

Thermal Arc Spray Overview

NASA Astrophysics Data System (ADS)

Hafiz Abd Malek, Muhamad; Hayati Saad, Nor; Kiyai Abas, Sunhaji; Mohd Shah, Noriyati

2013-06-01

Usage of protective coating for corrosion protection was on highly demand during the past decade; and thermal spray coating played a major part during that time. In recent years, the thermal arc spray coating becomes a popular coating. Many big players in oil and gas such as PETRONAS, EXXON MOBIL and SHELL in Malaysia tend to use the coating on steel structure as a corrosion protection. Further developments in coating processes, the devices, and raw materials have led to expansion of functional coatings and applications scope from conventional coating to specialized industries. It is widely used because of its ability to withstand high process temperature, offer advantages in efficiency, lower cost and acts as a corrosion protection. Previous research also indicated that the thermal arc spray offers better coating properties compared to other methods of spray. This paper reviews some critical area of thermal spray coating by discussing the process/parameter of thermal arc spray technology and quality control of coating. Coating performance against corrosion, wear and special characteristic of coating are also described. The field application of arc spray technology are demonstrated and reviewed.

INEL Spray-forming Research

NASA Technical Reports Server (NTRS)

Mchugh, Kevin M.; Key, James F.

1993-01-01

Spray forming is a near-net-shape fabrication technology in which a spray of finely atomized liquid droplets is deposited onto a suitably shaped substrate or mold to produce a coherent solid. The technology offers unique opportunities for simplifying materials processing without sacrificing, and oftentimes substantially improving, product quality. Spray forming can be performed with a wide range of metals and nonmetals, and offers property improvements resulting from rapid solidification (e.g., refined microstructures, extended solid solubilities and reduced segregation). Economic benefits result from process simplification and the elimination of unit operations. Researchers at the Idaho National Engineering Laboratory (INEL) are developing spray-forming technology for producing near-net-shape solids and coatings of a variety of metals, polymers, and composite materials. Results from several spray forming programs are presented to illustrate the range of capabilities of the technique as well as the accompanying technical and economic benefits. Low-carbon steel strip greater than 0.75 mm thick and polymer membranes for gas/gas and liquid/liquid separations that were spray formed are discussed; recent advances in spray forming molds, dies, and other tooling using low-melting-point metals are described.

Darkness and depth in early Renaissance painting

NASA Astrophysics Data System (ADS)

Tyler, Christopher

2010-02-01

Contrast has always been appreciated as a significant factor in image quality, but it is less widely recognized that it is a key factor in the representation of depth, solidity and three-dimensionality in images in general, and in paintings in particular. This aspect of contrast was a key factor in the introduction of oil paint as a painting medium at the beginning of the fifteenth century, as a practical means of contrast enhancement. However, recent conservatorship efforts have established that the first oil paintings were not, as commonly supposed, by van Eyck in Flanders in the 1430s, but by Masolino da Panicale in Italy in the 1420s. These developments led to the use of chiaroscuro technique in various forms, all of which are techniques for enhanced shadowing.

Permanent-Change Thermal Paints for Hypersonic Flight-Test

DTIC Science & Technology

2010-09-24

thermochromic liquid crystals (Ireland et al. 1999, Ireland & Jones 2000), and temperature sensitive paints (Liu & Sullivan 2005), thermal paints are...surfaces and fin-fuselage junctions, shock boundary layer interactions, scramjet combustion chambers and around control thrusters. Thermal paints can...use of discrete wired sensors may also not practical on some locations on a hypersonic vehicle. Thermochromic liquid crystals Coatings of

Measurements in liquid fuel sprays

NASA Technical Reports Server (NTRS)

Chigier, N.

1984-01-01

Techniques for studying the events directly preceding combustion in the liquid fuel sprays are being used to provide information as a function of space and time on droplet size, shape, number density, position, angle of flight and velocity. Spray chambers were designed and constructed for: (1) air-assist liquid fuel research sprays; (2) high pressure and temperature chamber for pulsed diesel fuel sprays; and (3) coal-water slurry sprays. Recent results utilizing photography, cinematography, and calibration of the Malvern particle sizer are reported. Systems for simultaneous measurement of velocity and particle size distributions using laser Doppler anemometry interferometry and the application of holography in liquid fuel sprays are being calibrated.

Pigeons can discriminate "good" and "bad" paintings by children.

PubMed

Watanabe, Shigeru

2010-01-01

Humans have the unique ability to create art, but non-human animals may be able to discriminate "good" art from "bad" art. In this study, I investigated whether pigeons could be trained to discriminate between paintings that had been judged by humans as either "bad" or "good". To do this, adult human observers first classified several children's paintings as either "good" (beautiful) or "bad" (ugly). Using operant conditioning procedures, pigeons were then reinforced for pecking at "good" paintings. After the pigeons learned the discrimination task, they were presented with novel pictures of both "good" and "bad" children's paintings to test whether they had successfully learned to discriminate between these two stimulus categories. The results showed that pigeons could discriminate novel "good" and "bad" paintings. Then, to determine which cues the subjects used for the discrimination, I conducted tests of the stimuli when the paintings were of reduced size or grayscale. In addition, I tested their ability to discriminate when the painting stimuli were mosaic and partial occluded. The pigeons maintained discrimination performance when the paintings were reduced in size. However, discrimination performance decreased when stimuli were presented as grayscale images or when a mosaic effect was applied to the original stimuli in order to disrupt spatial frequency. Thus, the pigeons used both color and pattern cues for their discrimination. The partial occlusion did not disrupt the discriminative behavior suggesting that the pigeons did not attend to particular parts, namely upper, lower, left or right half, of the paintings. These results suggest that the pigeons are capable of learning the concept of a stimulus class that humans name "good" pictures. The second experiment showed that pigeons learned to discriminate watercolor paintings from pastel paintings. The subjects showed generalization to novel paintings. Then, as the first experiment, size reduction test

The identification of synthetic organic pigments in modern paints and modern paintings using pyrolysis-gas chromatography-mass spectrometry.

PubMed

Russell, Joanna; Singer, Brian W; Perry, Justin J; Bacon, Anne

2011-05-01

A collection of more than 70 synthetic organic pigments were analysed using pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS). We report on the analysis of diketo-pyrrolo-pyrrole, isoindolinone and perylene pigments which are classes not previously reported as being analysed by this technique. We also report on a number of azo pigments (2-naphthol, naphthol AS, arylide, diarylide, benzimidazolone and disazo condensation pigments) and phthalocyanine pigments, the Py-GC-MS analysis of which has not been previously reported. The members of each class were found to fragment in a consistent way and the pyrolysis products are reported. The technique was successfully applied to the analysis of paints used by the artist Francis Bacon (1909-1992), to simultaneously identify synthetic organic pigments and synthetic binding media in two samples of paint taken from Bacon's studio and micro-samples taken from three of his paintings and one painting attributed to him.

Paintings discrimination by mice: Different strategies for different paintings.

PubMed

Watanabe, Shigeru

2017-09-01

C57BL/6 mice were trained on simultaneous discrimination of paintings with multiple exemplars, using an operant chamber with a touch screen. The number of exemplars was successively increased up to six. Those mice trained in Kandinsky/Mondrian discrimination showed improved learning and generalization, whereas those trained in Picasso/Renoir discrimination showed no improvements in learning or generalization. These results suggest category-like discrimination in the Kandinsky/Mondrian task, but item-to-item discrimination in the Picasso/Renoir task. Mice maintained their discriminative behavior in a pixelization test with various paintings; however, mice in the Picasso/Renoir task showed poor performance in a test that employed scrambling processing. These results do not indicate that discrimination strategy for any Kandinsky/Mondrian combinations differed from that for any Picasso/Monet combinations but suggest the mice employed different strategies of discrimination tasks depending upon stimuli. Copyright © 2017 Elsevier B.V. All rights reserved.

Hair spray poisoning

MedlinePlus

... this page: //medlineplus.gov/ency/article/002705.htm Hair spray poisoning To use the sharing features on this page, please enable JavaScript. Hair spray poisoning occurs when someone breathes in (inhales) ...

76 FR 17379 - National Tree-Marking Paint Committee Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-29

... DEPARTMENT OF AGRICULTURE Forest Service National Tree-Marking Paint Committee Meeting AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The National Tree-Marking Paint Committee will... related to improvements in, concerns about, and the handling and use of tree-marking paint by personnel of...

77 FR 20612 - National Tree-Marking Paint Committee Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-05

... DEPARTMENT OF AGRICULTURE Forest Service National Tree-Marking Paint Committee Meeting AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The National Tree-Marking Paint Committee will... related to improvements in, concerns about, and the handling and use of tree-marking paint by personnel of...

An Augmented γ-Spray System to Visualize Biological Effects for Human Body

NASA Astrophysics Data System (ADS)

Manabe, Seiya; Tenzou, Hideki; Kasuga, Takaaki; Iwakura, Yukiko; Johnston, Robert

2017-09-01

The purpose of this study was to develop a new educational system with an easy-to-use interface in order to support comprehension of the biological effects of radiation on the human body within a short period of time. A paint spray-gun was used as a gamma rays source mock-up for the system. The application screen shows the figure of a human body for radiation deposition using the γ-Sprayer, a virtual radiation source, as well as equivalent dosage and a panel for setting the irradiation conditions. While the learner stands in front of the PC monitor, the virtual radiation source is used to deposit radiation on the graphic of the human body that is displayed. Tissue damage is calculated using an interpolation method from the data calculated by the PHITS simulation code in advance while the learner is pulling the trigger with respect to the irradiation time, incident position, and distance from the screen. It was confirmed that the damage was well represented by the interpolation method. The augmented ?-Spray system was assessed by questionnaire. Pre-post questionnaire was taken for our 41 students in National Institute of Technology, Kagawa College. It was also confirmed that the system has a capability of teaching the basic radiation protection concept, quantitative feeling of the radiation dose, and the biological effects

Detecting Corrosion Under Paint and Insulation

NASA Technical Reports Server (NTRS)

Bastin, Gary L.

2011-01-01

Corrosion is a major concern at the Kennedy Space Center in Florida due to the proximity of the center to the Atlantic Ocean and to salt water lagoons. High humidity, salt fogs, and ocean breezes, provide an ideal environment in which painted steel structures become corroded. Maintenance of painted steel structures is a never-ending process.

Roosters Rule: A Painted Paper Collage

ERIC Educational Resources Information Center

Brady, Susan

2011-01-01

On perusing American collage artist Eric Carle's book, "Rooster's Off to See the World," at an annual school book fair, the author, mesmerized by the carnival of colors and collage on each page, thought "What a wonderful visual aid for a combination painting and collage unit." Her first-graders were involved in a painting unit, and knowing their…

Reappraising Abstract Paintings after Exposure to Background Information

PubMed Central

Park, Seongmin A.; Yun, Kyongsik; Jeong, Jaeseung

2015-01-01

Can knowledge help viewers when they appreciate an artwork? Experts’ judgments of the aesthetic value of a painting often differ from the estimates of naïve viewers, and this phenomenon is especially pronounced in the aesthetic judgment of abstract paintings. We compared the changes in aesthetic judgments of naïve viewers while they were progressively exposed to five pieces of background information. The participants were asked to report their aesthetic judgments of a given painting after each piece of information was presented. We found that commentaries by the artist and a critic significantly increased the subjective aesthetic ratings. Does knowledge enable experts to attend to the visual features in a painting and to link it to the evaluative conventions, thus potentially causing different aesthetic judgments? To investigate whether a specific pattern of attention is essential for the knowledge-based appreciation, we tracked the eye movements of subjects while viewing a painting with a commentary by the artist and with a commentary by a critic. We observed that critics’ commentaries directed the viewers’ attention to the visual components that were highly relevant to the presented commentary. However, attention to specific features of a painting was not necessary for increasing the subjective aesthetic judgment when the artists’ commentary was presented. Our results suggest that at least two different cognitive mechanisms may be involved in knowledge- guided aesthetic judgments while viewers reappraise a painting. PMID:25945789

Remotely controlled spray gun

NASA Technical Reports Server (NTRS)

Cunningham, William C. (Inventor)

1987-01-01

A remotely controlled spray gun is described in which a nozzle and orifice plate are held in precise axial alignment by an alignment member, which in turn is held in alignment with the general outlet of the spray gun by insert. By this arrangement, the precise repeatability of spray patterns is insured.

29 CFR 1915.33 - Chemical paint and preservative removers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

29 CFR 1915.33 - Chemical paint and preservative removers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 7 2011-07-01 2011-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

29 CFR 1915.33 - Chemical paint and preservative removers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 7 2014-07-01 2014-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

29 CFR 1915.33 - Chemical paint and preservative removers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 7 2013-07-01 2013-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

29 CFR 1915.33 - Chemical paint and preservative removers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 7 2012-07-01 2012-07-01 false Chemical paint and preservative removers. 1915.33 Section... Preparation and Preservation § 1915.33 Chemical paint and preservative removers. (a) Employees shall be protected against skin contact during the handling and application of chemical paint and preservative...

Pacific Southwest Lead-Based Paint Tips & Complaints

EPA Pesticide Factsheets

Information about submitting a complaint about improper removal or storage of lead-based paint in renovations or repairs, as well as disclosure of lead-based paint in real estate transactions in AZ, CA, NV, HI, and Pacific Island Territories.

Laser cleaning treatment of burnt paintings

NASA Astrophysics Data System (ADS)

Antonopoulou-Athera, N.; Chatzitheodoridis, E.; Doulgerides, M.; Evangelatos, Ch.; Serafetinides, A. A.; Terlixi, A.

2015-01-01

Three samples taken from two paintings partly burned by fire are investigated for cleaning with lasers. The paintings belong to the collection of the National Gallery of Athens and were made by the great Greek artist Konstantinos Parthenis. To remove the damaged surface and achieve an acceptable restoration result, the optimum combination of fluence and wavelength are sought. Seven different wavelengths with a set of fluences where used, i.e., the five harmonics of a Nd:YAG laser (1064, 532, 355, 266, and 213 nm), a TEA 10.6 μm CO2 and a free running laser Er:YAG 2.94 μm. Characterization was performed prior and after the cleaning process by optical and electron microscopy and analysis (SEM/BSE EDS), as well as X-Ray Diffraction (XRD). The results of this work indicate that the wavelength in the visible spectrum (532 nm) with fluences between 0.1-0.4J/cm2 show the optimum cleaning. The optical microscopy observation shows that with these laser parameters the burnt layer was preferentially removed, exposing the original colors that Parthenis had used in these paintings. Electron microscopy imaging and chemical analysis revealed that the original texture and materials of these samples are preserved after irradiation. Since the damage varies along the surface of the painting, more experiments should be performed in order to find and optimize the full cleaning and characterization process for the homogeneous cleaning of the whole surface of the painting.

Comparision on dynamic behavior of diesel spray and rapeseed oil spray in diesel engine

NASA Astrophysics Data System (ADS)

Sapit, Azwan; Azahari Razali, Mohd; Faisal Hushim, Mohd; Jaat, Norrizam; Nizam Mohammad, Akmal; Khalid, Amir

2017-04-01

Fuel-air mixing is important process in diesel combustion. It significantly affects the combustion and emission of diesel engine. Biomass fuel has high viscosity and high distillation temperature and may negatively affect the fuel-air mixing process. Thus, study on the spray development and atomization of this type of fuel is important. This study investigates the atomization characteristics and droplet dynamic behaviors of diesel engine spray fuelled by rapeseed oil (RO) and comparison to diesel fuel (GO). Optical observation of RO spray was carried out using shadowgraph photography technique. Single nano-spark photography technique was used to study the characteristics of the spray while dual nano-spark shadowgraph technique was used to study the spray droplet behavior. Using in-house image processing algorithm, the images were processed and the boundary condition of each spray was also studied. The results show that RO has very poor atomization due to the high viscosity nature of the fuel when compared to GO. This is in agreement with the results from spray droplet dynamic behavior studies that shows due to the high viscosity, the RO spray droplets are large in size and travel downward, with very little influence of entrainment effect due to its large kinematic energy.

75 FR 18237 - Natural Bristle Paint Brushes From China

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-09

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-244 (Third Review)] Natural Bristle Paint... determination to conduct a full five-year review concerning the antidumping duty order on natural bristle paint... revocation of the antidumping duty order on natural bristle paint brushes from China would be likely to lead...

Paint and Pregnancy

MedlinePlus

... of paints used for industry, the arts, and hobbies. Years ago, lead and mercury were used in ... high amounts of toluene – higher exposure than a hobby or professional painter would likely have. I work ...

Development of a water-jet assisted laser paint removal process

NASA Astrophysics Data System (ADS)

Madhukar, Yuvraj K.; Mullick, Suvradip; Nath, Ashish K.

2013-12-01

The laser paint removal process usually leaves behind traces of combustion product i.e. ashes on the surface. An additional post-processing such as light-brushing or wiping by some mechanical means is required to remove the residual ash. In order to strip out the paint completely from the surface in a single step, a water-jet assisted laser paint removal process has been investigated. The 1.07 μm wavelength of Yb-fiber laser radiation has low absorption in water; therefore a high power fiber laser was used in the experiment. The laser beam was delivered on the paint-surface along with a water jet to remove the paint and residual ashes effectively. The specific energy, defined as the laser energy required removing a unit volume of paint was found to be marginally more than that for the gas-jet assisted laser paint removal process. However, complete paint removal was achieved with the water-jet assist only. The relatively higher specific energy in case of water-jet assist is mainly due to the scattering of laser beam in the turbulent flow of water-jet.

78 FR 20295 - National Tree-Marking Paint Committee Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-04

... Tree-Marking Paint Committee Meeting AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The National Tree-Marking Paint Committee will meet in Awendaw, SC on May 21-23, 2013. The purpose of... use of tree-marking paint by personnel of the Forest Service and the Department of the Interior...

Honeybees can discriminate between Monet and Picasso paintings.

PubMed

Wu, Wen; Moreno, Antonio M; Tangen, Jason M; Reinhard, Judith

2013-01-01

Honeybees (Apis mellifera) have remarkable visual learning and discrimination abilities that extend beyond learning simple colours, shapes or patterns. They can discriminate landscape scenes, types of flowers, and even human faces. This suggests that in spite of their small brain, honeybees have a highly developed capacity for processing complex visual information, comparable in many respects to vertebrates. Here, we investigated whether this capacity extends to complex images that humans distinguish on the basis of artistic style: Impressionist paintings by Monet and Cubist paintings by Picasso. We show that honeybees learned to simultaneously discriminate between five different Monet and Picasso paintings, and that they do not rely on luminance, colour, or spatial frequency information for discrimination. When presented with novel paintings of the same style, the bees even demonstrated some ability to generalize. This suggests that honeybees are able to discriminate Monet paintings from Picasso ones by extracting and learning the characteristic visual information inherent in each painting style. Our study further suggests that discrimination of artistic styles is not a higher cognitive function that is unique to humans, but simply due to the capacity of animals-from insects to humans-to extract and categorize the visual characteristics of complex images.

40 CFR 63.4765 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

... coating, curing, and drying occurs within the capture system; and the removal or evaporation of cleaning... criterion is not met if parts enter the open shop environment when being moved between a spray booth and a... activities and drying or curing time. (c) Liquid-to-uncaptured-gas protocol using a temporary total enclosure...

40 CFR 63.4165 - How do I determine the emission capture system efficiency?

Code of Federal Regulations, 2010 CFR

2010-07-01

... system; coating solvent flash-off and coating, curing, and drying occurs within the capture system and... when being moved between a spray booth and a curing oven. (b) If the capture system does not meet both... surface preparation activities and drying or curing time. (c) Liquid-to-uncaptured-gas protocol using a...

Swine flu (H1N1 influenza): awareness profile of visitors of swine flu screening booths in Belgaum city, Karnataka.

PubMed

Viveki, R G; Halappanavar, A B; Patil, M S; Joshi, A V; Gunagi, Praveena; Halki, Sunanda B

2012-06-01

The 2009 flu pandemic was a global outbreak of a new strain of H1N1 influenza virus often referred colloquially as "swine flu". The objectives of the study were: (1) To know the sociodemographic and awareness profile of visitors attending swine flu screening booths. (2) To reveal sources of information. The present cross-sectional study was undertaken among the visitors (18 years and above) attending swine flu screening booths organised within the Belgaum city during Ganesh festival from 28-08-2009 to 03-09-2009 by interviewing them using predesigned, pretested structured questionnaire on swine flu. The data was collected and analysed using SPSS software programme for windows (version 16). Chi-square test was applied. Out of 206 visitors, 132 (64.1%) were males and 107 (51.9%) were in the age group of 30-49 years; 183 (88.8%) had heard about swine flu. More than a third of the visitors (38.3%) disclosed that there was a vaccine to prevent swine flu. Majority responded that it could be transmitted by being in close proximity to pigs (49.0%) and by eating pork (51.5%). Newspaper/magazine (64.6%), television (61.7%), and public posters/pamphlets (44.2%) were common sources of information. The present study revealed that doctors/public health workers have played little role in creating awareness in the community. The improved communication between doctors and the community would help to spread correct information about the disease and the role that the community can play in controlling the spread of the disease.

FHWA Field Manual for Bridge Painting Inspection

DOT National Transportation Integrated Search

1997-10-01

This manual is a model to be followed by bridge paint inspectors on how to perform inspection duties properly. Given that most of today's bridge-paint work is being done on existing steel, this manual is geared toward people working in the field on e...

Alkali Silicate Vehicle Forms Durable, Fireproof Paint

NASA Technical Reports Server (NTRS)

Schutt, John B.; Seindenberg, Benjamin

1964-01-01

The problem: To develop a paint for use on satellites or space vehicles that exhibits high resistance to cracking, peeling, or flaking when subjected to a wide range of temperatures. Organic coatings will partially meet the required specifications but have the inherent disadvantage of combustibility. Alkali-silicate binders, used in some industrial coatings and adhesives, show evidence of forming a fireproof paint, but the problem of high surface-tension, a characteristic of alkali silicates, has not been resolved. The solution: Use of a suitable non-ionic wetting agent combined with a paint incorporating alkali silicate as the binder.

Comparison of the reflectance characteristics of polytetrafluoroethylene and barium sulfate paints

NASA Technical Reports Server (NTRS)

Butner, C. L.; Schutt, J. B.; Shai, M. C.

1984-01-01

Preliminary results are presented of the directional reflectance measurements taken on two tetrafluorethylene (TFE) paints formulated with silicone binders. Both paints are found to be more Lambertian than barium sulfate paint and pressed powder, although the pigment to binder ratios for barium sulfate and TFE paints are about 133 and 3.3 to 1, respectively. The TFE paints exhibit total visible reflectances above 90 percent and offer surfaces that are not significantly affected by water.

Particle size distribution of aerosols sprayed from household hand-pump sprays containing fluorine-based and silicone-based compounds.

PubMed

Kawakami, Tsuyoshi; Isama, Kazuo; Ikarashi, Yoshiaki

2015-01-01

Japan has published safety guideline on waterproof aerosol sprays. Furthermore, the Aerosol Industry Association of Japan has adopted voluntary regulations on waterproof aerosol sprays. Aerosol particles of diameter less than 10 µm are considered as "fine particles". In order to avoid acute lung injury, this size fraction should account for less than 0.6% of the sprayed aerosol particles. In contrast, the particle size distribution of aerosols released by hand-pump sprays containing fluorine-based or silicone-based compounds have not been investigated in Japan. Thus, the present study investigated the aerosol particle size distribution of 16 household hand-pump sprays. In 4 samples, the ratio of fine particles in aerosols exceeded 0.6%. This study confirmed that several hand-pump sprays available in the Japanese market can spray fine particles. Since the hand-pump sprays use water as a solvent and their ingredients may be more hydrophilic than those of aerosol sprays, the concepts related to the safety of aerosol-sprays do not apply to the hand pump sprays. Therefore, it may be required for the hand-pump spray to develop a suitable method for evaluating the toxicity and to establish the safety guideline.

A review on paint sludge from automotive industries: Generation, characteristics and management.

PubMed

Salihoglu, Guray; Salihoglu, Nezih Kamil

2016-03-15

The automotive manufacturing process results in the consumption of several natural sources and the generation of various types of wastes. The primary source of hazardous wastes at an automotive manufacturing plant is the painting process, and the major waste fraction is paint sludge, which is classified with EU waste code of 080113* implying hazardous characteristics. The amount of the paint sludge generated increases every year with the worldwide increase in the car production. The characteristics of the paint sludge, which mainly designate the management route, are mainly determined by the type of the paint used, application technique employed, and the chemicals applied such as flocculants, detackifiers, pH boosters, antifoam agents, and biocides as well as the dewatering techniques preferred. Major routes for the disposal of the paint sludges are incineration as hazardous waste or combustion at cement kilns. Because of high dissolved organic carbon content of the paint, the paint sludge cannot be accepted by landfills according to European Union Legislations. More investigations are needed in the field of paint sludge recycling such as recycling it as a new paint or as other formulations, or making use of the sludge for the production of construction materials. Research on the applicability of the paint sludge in composting and biogasification can also be useful. Ongoing research is currently being conducted on new application techniques to increase the effectiveness of paint transfer, which helps to prevent the generation of paint sludge. Advancements in paint and coating chemistry such as the reduction in the coating layers with its thickness also help to decrease the level of paint sludge generation. Investigations on the effects of the chemicals on the recycling potential of paint sludges and consideration of these effects by the chemical manufacturer companies would be extremely important. This review presents the formation of paint sludge, the factors

Does antifouling paint select for antibiotic resistance?

PubMed

Flach, Carl-Fredrik; Pal, Chandan; Svensson, Carl Johan; Kristiansson, Erik; Östman, Marcus; Bengtsson-Palme, Johan; Tysklind, Mats; Larsson, D G Joakim

2017-07-15

There is concern that heavy metals and biocides contribute to the development of antibiotic resistance via co-selection. Most antifouling paints contain high amounts of such substances, which risks turning painted ship hulls into highly mobile refuges and breeding grounds for antibiotic-resistant bacteria. The objectives of this study were to start investigate if heavy-metal based antifouling paints can pose a risk for co-selection of antibiotic-resistant bacteria and, if so, identify the underlying genetic basis. Plastic panels with one side painted with copper and zinc-containing antifouling paint were submerged in a Swedish marina and biofilms from both sides of the panels were harvested after 2.5-4weeks. DNA was isolated from the biofilms and subjected to metagenomic sequencing. Biofilm bacteria were cultured on marine agar supplemented with tetracycline, gentamicin, copper sulfate or zinc sulfate. Biofilm communities from painted surfaces displayed lower taxonomic diversity and enrichment of Gammaproteobacteria. Bacteria from these communities showed increased resistance to both heavy metals and tetracycline but not to gentamicin. Significantly higher abundance of metal and biocide resistance genes was observed, whereas mobile antibiotic resistance genes were not enriched in these communities. In contrast, we found an enrichment of chromosomal RND efflux system genes, including such with documented ability to confer decreased susceptibility to both antibiotics and biocides/heavy metals. This was paralleled by increased abundances of integron-associated integrase and ISCR transposase genes. The results show that the heavy metal-based antifouling paint exerts a strong selection pressure on marine bacterial communities and can co-select for certain antibiotic-resistant bacteria, likely by favoring species and strains carrying genes that provide cross-resistance. Although this does not indicate an immediate risk for promotion of mobile antibiotic resistance, the

EVALUATION OF CONVERGENT SPRAY TECHNOLOGYTM SPRAY PROCESS FOR ROOF COATING APPLICATION

EPA Science Inventory

The overall goal of this project was to demonstrate the feasibility of Convergent Spray TechnologyTM for the roofing industry. This was accomplished by producing an environmentally compliant coating utilizing recycled materials, a CSTTM spray process portable application cart, a...

Prevention of VOC releases from bridge painting operations.

DOT National Transportation Integrated Search

2007-06-01

Bridge maintenance painting employs solvent-based coatings that generate volatile organic compounds (VOCs) that contribute to air-quality problems. Methods for capturing VOCs during normal Kentucky Transportation Cabinet (KYTC) maintenance painting o...

[Chemical hazards in the workplace environment of painting restorer].

PubMed

Jezewska, Anna; Szewczyńska, Małgorzata

2012-01-01

This paper presents the results of the identification of chemical substances present in the air in the workplace of painting restorer. Identification tests were carried out in university and museum easel paintings conservation studios. Air samples were taken for testing at various stages of restoration works. In the qualitative analysis chemical substances in the air samples were measured by GC-MSD and HPLC-DAD methods. In the air samples collected during the cleaning of paintings, such substances as aliphatic and aromatic hydrocarbons, acetone, ethanol and terpenes were mainly identified. While the painting was doubled toluene and while varnished, propan-2-ol, propane, butane and substances derived from turpentine and white spirit were mainly emitted. During the course of painting conservation numerous chemical substances that may pose a threat to the worker's health were identified in their breathing zone.

33 CFR 118.140 - Painting bridge piers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Painting bridge piers. 118.140 Section 118.140 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.140 Painting bridge piers. The District Commander may require...

33 CFR 118.140 - Painting bridge piers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Painting bridge piers. 118.140 Section 118.140 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.140 Painting bridge piers. The District Commander may require...

Evaluation of Convergent Spray Technology(TM) Spray Process for Roof Coating Application

NASA Technical Reports Server (NTRS)

Scarpa, J.; Creighton, B.; Hall, T.; Hamlin, K.; Howard, T.

1998-01-01

The overall goal of this project was to demonstrate the feasibility of(CST) Convergent Spray Technology (Trademark) for the roofing industry. This was accomplished by producing an environmentally compliant coating utilization recycled materials, a CST(Trademark) spray process portable application cart, and hand-held applicator with a CST(Trademark) spray process nozzle. The project culminated with application of this coating to a nine hundred sixty square foot metal for NASA Marshall Space Flight Center (MSFC) in Huntsville, Alabama.

CFD Simulation of Aerial Crop Spraying

NASA Astrophysics Data System (ADS)

Omar, Zamri; Qiang, Kua Yong; Mohd, Sofian; Rosly, Nurhayati

2016-11-01

Aerial crop spraying, also known as crop dusting, is made for aerial application of pesticides or fertilizer. An agricultural aircraft which is converted from an aircraft has been built to combine with the aerial crop spraying for the purpose. In recent years, many studies on the aerial crop spraying were conducted because aerial application is the most economical, large and rapid treatment for the crops. The main objective of this research is to study the airflow of aerial crop spraying system using Computational Fluid Dynamics. This paper is focus on the effect of aircraft speed and nozzle orientation on the distribution of spray droplet at a certain height. Successful and accurate of CFD simulation will improve the quality of spray during the real situation and reduce the spray drift. The spray characteristics and efficiency are determined from the calculated results of CFD. Turbulence Model (k-ɛ Model) is used for the airflow in the fluid domain to achieve a more accurate simulation. Furthermore, spray simulation is done by setting the Flat-fan Atomizer Model of Discrete Phase Model (DPM) at the nozzle exit. The interaction of spray from each flat-fan atomizer can also be observed from the simulation. The evaluation of this study is validation and grid dependency study using field data from industry.

Foaming Betadine Spray as a potential agent for non-labor-intensive preoperative surgical site preparation.

PubMed

Kargupta, Roli; Hull, Garret J; Rood, Kyle D; Galloway, James; Matthews, Clinton F; Dale, Paul S; Sengupta, Shramik

2015-04-02

The Centers for Disease Control and Prevention's (CDC) National Healthcare Safety Network (NHSN) report published in 2009 shows that there were about 16,000 cases of surgical site infection (SSI) following ~ 850,000 operative procedures making SSI one of the most predominant infection amongst nosocomial infections. Preoperative skin preparation is a standard procedure utilized to prevent SSIs thereby improving patient outcomes and controlling associated healthcare costs. Multiple techniques/ products have been used for pre-operative skin preparation, like 2 step scrubbing and painting, 2 step scrubbing and drying, and 1 step painting with a drying time. However, currently used products require strict, time consuming and labor-intensive protocols that involve repeated mechanical scrubbing. It can be speculated that a product requiring a more facile protocol will increase compliance, thus promoting a reduction in SSIs. Hence, the antimicrobial efficacy of a spray-on foaming formulation containing Betadine (povidone-iodine aerosol foam) that can be administered with minimum effort is compared to that of an existing formulation/technique (Wet Skin Scrub). In vitro antimicrobial activities of (a) 5% Betadine delivered in aerosolized foam, (b) Wet Skin Scrub Prep Tray and (c) liquid Betadine are tested against three clinically representative microorganisms (S. aureus, S. epidermidis and P. aeruginosa,) on two surfaces (agar-gel on petri-dish and porcine skin). The log reduction/growth of the bacteria in each case is noted and ANOVA statistical analysis is used to establish the effectiveness of the antimicrobial agents, and compare their relative efficacies. With agar gel as the substrate, no growth of bacteria is observed for all the three formulations. With porcine skin as the substrate, the spray-on foam's performance was not statistically different from that of the Wet Skin Scrub Prep technique for the microorganisms tested. The povidone-iodine aerosolized foam

Liquid spray experiments

NASA Astrophysics Data System (ADS)

Lapham, Gary; McHugh, John

When waves on the ocean surface interact with a solid object, the result is often a complex pattern of spray. The solid object may be a coastal barrier such as a breakwater, or a ship or drilling rig. Another spray-related case is the presence of large industrial tanks of liquid, and often dangerous liquids, that exist around the world. Tens of thousands of such tanks are rapidly becoming obsolete. Recent experience has shown that when such tanks burst, the resulting spray may shoot several hundreds of meters from the tank. These tanks often have a wall or dam (barrier) surrounding them in an attempt to contain any leakage, catastrophic or otherwise. When the tank bursts it is akin to the dam-break problem. A wall of water rushes forth and impinges on the barrier creating spray. Previous experiments (McHugh and Watt, 1998) considered the related configuration of a solitary wave impinging on a vertical wall. The present experiments more closely model the bursting tank case, and treat the effect of the distance between the tank and barrier. Results show that there is a sweet spot where height and horizontal distance of spray droplets are maximized. This ideal distance between tank and barrier is constant when scaled by the initial tank depth.

Modifications Of A Commercial Spray Gun

NASA Technical Reports Server (NTRS)

Allen, Peter B.

1993-01-01

Commercial spray gun modified to increase spray rate and make sprayed coats more nearly uniform. Consists of gun head and pneumatic actuator. Actuator opens valves for two chemical components, called "A" and "B," that react to produce foam. Components flow through orifices, into mixing chamber in head. Mixture then flows through control orifice to spray tip. New spray tip tapered to reduce area available for accumulation of foam and makes tip easier to clean.

29 CFR 1915.34 - Mechanical paint removers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Mechanical paint removers. 1915.34 Section 1915.34 Labor... Preservation § 1915.34 Mechanical paint removers. (a) Power tools. (1) Employees engaged in the removal of... confined space, mechanical exhaust ventilation sufficient to keep the dust concentration to a minimum shall...

13 CFR 120.173 - Lead-based paint.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Lead-based paint. 120.173 Section 120.173 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Policies Applying to All Business Loans Requirements Imposed Under Other Laws and Orders § 120.173 Lead-based paint. If...

CAPSTONE REPORT ON THE DEVELOPMENT OF A STANDARD TEST METHOD FOR VOC EMISSIONS FROM INTERIOR LATEX PAINT AND ALKYD PAINTS

EPA Science Inventory

The report gives details of a small-chamber test method developed by the EPA for characterizing volatile organic compound (VOC) emissions from interior latex and alkyd paints. Current knowledge about VOC, including hazardous air pollutant, emissions from interior paints generated...

Wind tunnel and field evaluation of drift from aerial spray applications with multiple spray formulations

USDA-ARS?s Scientific Manuscript database

The impact of different spray tank modifiers into an active ingredient spray mixture on spray atomization and in-field behavior under aerial application conditions were examined. Wind tunnel tests demonstrated that active ingredient solutions potentially results in significantly different atomizati...

Analytical characterization of the palette and painting techniques of Jorge Afonso, the great 16th century Master of Lisbon painting workshop

NASA Astrophysics Data System (ADS)

Antunes, Vanessa; Candeias, António; Mirão, José; Carvalho, Maria L.; Dias, Cristina Barrocas; Manhita, Ana; Cardoso, Ana; Francisco, Maria J.; Lauw, Alexandra; Manso, Marta

2018-03-01

In this work, a study on a set of paintings from the most significant altarpiece assigned to Master Jorge Afonso (c. 1470-1540) painting workshop is presented. This altarpiece is composed by fourteen paintings made to the church of Convento de Jesus, in Setúbal, Portugal, and was made circa 1517-19/1530, according to art-history. This set of paintings is compared to one of the other most important Portuguese altarpieces from the 16th century: the panels of the Round Church of the Convento de Cristo, in Tomar, made circa 1510-1515. The aim of this study is to characterize the wooden support, pigments, ground layers materials and technique used in Jorge Afonso workshop by means of complementary analyses. A dendrochronological approach was made in order to corroborate (or not) the historical date initially assigned. Infrared photography (IRP) and reflectography (IRR) allowed the study of the underdrawing technique and macro photography (MP) was used to recognize overlapping layers technique. Cross-sections from the paintings were examined by optical microscopy (OM), and analyzed by μ-X-ray diffraction (μ-XRD), Energy Dispersive X-ray Fluorescence spectroscopy (EDXRF), Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDS), micro-Raman spectroscopy (μ-Raman), micro-Fourier Transform Infrared spectroscopy (μ-FTIR), Pyrolysis Gas Chromatography Mass Spectrometry (py-GC/MS). The characterization of the palette and ground layers and the study of the overlapping of paint layers brought a new insight of the adopted painting techniques by the most important group of painters working in Portugal in the 16th century - the Lisbon workshop, leaded by Master Jorge Afonso.

Release and detection of nanosized copper from a commercial antifouling paint.

PubMed

Adeleye, Adeyemi S; Oranu, Ekene A; Tao, Mengya; Keller, Arturo A

2016-10-01

One major concern with the use of antifouling paints is the release of its biocides (mainly copper and zinc) into natural waters, where they may exhibit toxicity to non-target organisms. While many studies have quantified the release of biocides from antifouling paints, very little is known about the physicochemical state of released copper. For proper risk assessment of antifouling paints, characterization of copper released into water is necessary because the physicochemical state determines the metal's environmental fate and effects. In this study, we monitored release of different fractions of copper (dissolved, nano, and bulk) from a commercial copper-based antifouling paint. Release from painted wood and aluminum mini-bars that were submerged in natural waters was monitored for 180 days. Leachates contained both dissolved and particulate copper species. X-ray diffraction and X-ray photoelectron spectroscopy were used to determine the chemical phase of particles in the leachate. The amount of copper released was strongly dependent on water salinity, painted surface, and paint drying time. The presence of nanosized Cu2O particles was confirmed in paint and its leachate using single-particle inductively coupled plasma-mass spectrometry and electron microscopy. Toxicity of paint leachate to a marine phytoplankton was also evaluated. Copyright © 2016 Elsevier Ltd. All rights reserved.

The prevalence of lead-based paint hazards in U.S. housing.

PubMed Central

Jacobs, David E; Clickner, Robert P; Zhou, Joey Y; Viet, Susan M; Marker, David A; Rogers, John W; Zeldin, Darryl C; Broene, Pamela; Friedman, Warren

2002-01-01

In this study we estimated the number of housing units in the United States with lead-based paint and lead-based paint hazards. We included measurements of lead in intact and deteriorated paint, interior dust, and bare soil. A nationally representative, random sample of 831 housing units was evaluated in a survey between 1998 and 2000; the units and their occupants did not differ significantly from nationwide characteristics. Results indicate that 38 million housing units had lead-based paint, down from the 1990 estimate of 64 million. Twenty-four million had significant lead-based paint hazards. Of those with hazards, 1.2 million units housed low-income families (< 30,000 US dollars/year) with children under 6 years of age. Although 17% of government-supported, low-income housing had hazards, 35% of all low-income housing had hazards. For households with incomes greater than or equal to 30,000 US dollars/year, 19% had hazards. Fourteen percent of all houses had significantly deteriorated lead-based paint, and 16% and 7%, respectively, had dust lead and soil lead levels above current standards of the U.S. Department of Housing and Urban Development and the U.S. Environmental Protection Agency. The prevalence of lead-based paint and hazards increases with age of housing, but most painted surfaces, even in older housing, do not have lead-based paint. Between 2% and 25% of painted building components were coated with lead-based paint. Housing in the Northeast and Midwest had about twice the prevalence of hazards compared with housing in the South and West. The greatest risk occurs in older units with lead-based paint hazards that either will be or are currently occupied by families with children under 6 years of age and are low-income and/or are undergoing renovation or maintenance that disturbs lead-based paint. This study also confirms projections made in 2000 by the President's Task Force on Environmental Health Risks and Safety Risks to Children of the number of

Substrate system for spray forming

DOEpatents

Chu, Men G.; Chernicoff, William P.

2000-01-01

A substrate system for receiving a deposit of sprayed metal droplets including a movable outer substrate on which the sprayed metal droplets are deposited. The substrate system also includes an inner substrate disposed adjacent the outer substrate where the sprayed metal droplets are deposited on the outer substrate. The inner substrate includes zones of differing thermal conductivity to resist substrate layer porosity and to resist formation of large grains and coarse constituent particles in a bulk layer of the metal droplets which have accumulated on the outer substrate. A spray forming apparatus and associated method of spray forming a molten metal to form a metal product using the substrate system of the invention is also provided.

Substrate system for spray forming

DOEpatents

Chu, Men G.; Chernicoff, William P.

2002-01-01

A substrate system for receiving a deposit of sprayed metal droplets including a movable outer substrate on which the sprayed metal droplets are deposited. The substrate system also includes an inner substrate disposed adjacent the outer substrate where the sprayed metal droplets are deposited on the outer substrate. The inner substrate includes zones of differing thermal conductivity to resist substrate layer porosity and to resist formation of large grains and coarse constituent particles in a bulk layer of the metal droplets which have accumulated on the outer substrate. A spray forming apparatus and associated method of spray forming a molten metal to form a metal product using the substrate system of the invention is also provided.

24 CFR 35.1220 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Tenant-Based Rental Assistance § 35.1220 Ongoing lead-based paint maintenance activities...

24 CFR 35.1220 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Tenant-Based Rental Assistance § 35.1220 Ongoing lead-based paint maintenance activities...

24 CFR 35.1220 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Tenant-Based Rental Assistance § 35.1220 Ongoing lead-based paint maintenance activities...

24 CFR 35.1220 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Tenant-Based Rental Assistance § 35.1220 Ongoing lead-based paint maintenance activities...

24 CFR 35.1220 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Ongoing lead-based paint..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Tenant-Based Rental Assistance § 35.1220 Ongoing lead-based paint maintenance activities...

A spray flamelet/progress variable approach combined with a transported joint PDF model for turbulent spray flames

NASA Astrophysics Data System (ADS)

Hu, Yong; Olguin, Hernan; Gutheil, Eva

2017-05-01

A spray flamelet/progress variable approach is developed for use in spray combustion with partly pre-vaporised liquid fuel, where a laminar spray flamelet library accounts for evaporation within the laminar flame structures. For this purpose, the standard spray flamelet formulation for pure evaporating liquid fuel and oxidiser is extended by a chemical reaction progress variable in both the turbulent spray flame model and the laminar spray flame structures, in order to account for the effect of pre-vaporised liquid fuel for instance through use of a pilot flame. This new approach is combined with a transported joint probability density function (PDF) method for the simulation of a turbulent piloted ethanol/air spray flame, and the extension requires the formulation of a joint three-variate PDF depending on the gas phase mixture fraction, the chemical reaction progress variable, and gas enthalpy. The molecular mixing is modelled with the extended interaction-by-exchange-with-the-mean (IEM) model, where source terms account for spray evaporation and heat exchange due to evaporation as well as the chemical reaction rate for the chemical reaction progress variable. This is the first formulation using a spray flamelet model considering both evaporation and partly pre-vaporised liquid fuel within the laminar spray flamelets. Results with this new formulation show good agreement with the experimental data provided by A.R. Masri, Sydney, Australia. The analysis of the Lagrangian statistics of the gas temperature and the OH mass fraction indicates that partially premixed combustion prevails near the nozzle exit of the spray, whereas further downstream, the non-premixed flame is promoted towards the inner rich-side of the spray jet since the pilot flame heats up the premixed inner spray zone. In summary, the simulation with the new formulation considering the reaction progress variable shows good performance, greatly improving the standard formulation, and it provides new

Aerial vehicle with paint for detection of radiological and chemical warfare agents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, Joseph C.; Brunk, James L.; Day, S. Daniel

A paint that warns of radiological or chemical substances comprising a paint operatively connected to the surface, an indicator material carried by the paint that provides an indication of the radiological or chemical substances, and a thermo-activation material carried by the paint. In one embodiment, a method of warning of radiological or chemical substances comprising the steps of painting a surface with an indicator material, and monitoring the surface for indications of the radiological or chemical substances. In another embodiment, a paint is operatively connected to a vehicle and an indicator material is carried by the paint that provides anmore » indication of the radiological or chemical substances.« less

Electrical Resistivity of Wire Arc Sprayed Zn and Cu Coatings for In-Mold-Metal-Spraying

NASA Astrophysics Data System (ADS)

Bobzin, K.; Öte, M.; Knoch, M. A.; Liao, X.; Hopmann, Ch; Ochotta, P.

2018-06-01

Electrical functionalities can be integrated into plastic parts by integrating thermally sprayed metal coatings into the non-conductive base material. Thermally sprayed conducting tracks for power and signal transmission are one example. In this case, the electrical resistance or resistivity of the coatings should be investigated. Therefore, the electrical resistivity of wire arc sprayed Zn and Cu coatings has been investigated. In case of Zn coatings, spray distance, gas pressure and wire diameter could be identified as significant influencing parameters on the electrical resistivity. In contrast, process gas, gas pressure and voltage do have a significant influence on the electrical resistivity of Cu coatings. Through the use of the In-Mold-Metal-Spraying method (IMMS), thermal degradation can be avoided by transferring thermally sprayed coating from a mold insert onto the plastic part. Therefore, the influence of the transfer process on the electrical resistance of the coatings has also been investigated.

Fabrication and calibration of a piezoelectric nanocomposite paint

NASA Astrophysics Data System (ADS)

Osho, Samuel; Wu, Nan; Aramfard, Mohammad; Deng, Chuang; Ojo, Olanrewaju

2018-03-01

A new liquid form piezoelectric nanocomposite paint material is fabricated with possible applications as dynamic strain sensors and/or piezoelectric transducers. The applied coating is in the form of low-cost paint, which is flexible and bonds strongly on a metallic surface after drying out via the solvent-casting method. The nanocomposite is produced by an ultrasonic mixture of varying percentages of zinc oxide (ZnO) nanoparticle water dispersion, poly vinyl acetate glue (PVA) and carbon nanotubes (CNTs). ZnO nanoparticles are used as the piezoelectric sensing elements in a PVA matrix of the paint, while CNTs are introduced as robust bridge of ZnO particles enhancing the piezoelectricity and material properties. Transmission electron microscopy (TEM) images confirmed the linkages of ZnO nanoparticles in the composite by CNTs. Through piezoelectricity calibration, the optimum mixing ratio with the highest piezoelectricity is 78.1 wt% ZnO, 19.5 wt% PVA glue and 2.4 wt% multi-wall carbon nanotubes (MWCNTs). Through nanoindentation tests for the characterization of the mechanical properties of the nano-composite paint, it is found that Young’s modulus and hardness reached a threshold point in the increment in the addition of CNTs to the paint before showing signs of decline. Detailed analysis and explanation of the calibration results and physical phenomenon are provided. The stable paint material is ready to be applied on rough area of engineering structures as sensor and transducer.

24 CFR 35.935 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Rehabilitation § 35.935 Ongoing lead-based paint maintenance activities. In the case of a rental... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Ongoing lead-based paint...

24 CFR 35.935 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Rehabilitation § 35.935 Ongoing lead-based paint maintenance activities. In the case of a rental... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Ongoing lead-based paint...

24 CFR 35.935 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Rehabilitation § 35.935 Ongoing lead-based paint maintenance activities. In the case of a rental... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Ongoing lead-based paint...

24 CFR 35.935 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Rehabilitation § 35.935 Ongoing lead-based paint maintenance activities. In the case of a rental... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Ongoing lead-based paint...

24 CFR 35.935 - Ongoing lead-based paint maintenance activities.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Rehabilitation § 35.935 Ongoing lead-based paint maintenance activities. In the case of a rental... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Ongoing lead-based paint...

Influence of artificial accelerated ageing on the colour stability of paints used for ocular prosthesis iris painting.

PubMed

Mundim, Fabrício M; Antunes, Pedro L; Sousa, Ana Beatriz S; Garcia, Lucas F R; Pires-de-Souza, Fernanda C P

2012-06-01

To evaluate the colour stability of paints used for ocular prosthesis iris painting submitted for accelerated artificial ageing (AAA). Forty specimens of acrylic resin for sclera (16 × 2 mm) were made and separated into eight groups (n = 10) according to the type of paint (gouache, GP; oil, OP; acrylic AP; and composite resin for characterisation, CR) and the colours used (blue/brown). After drying (72 h), a new layer of colourless acrylic resin was applied and the initial colour readout was performed (Spectrophotometer PCB 6807). New colour readouts were performed after AAA, and ΔE was calculated. Statistical analysis (two-way anova-Bonferroni, p < 0.05) demonstrated that the brown colour showed lower ΔE means in comparison with the blue colour, with statistically significant difference for AP only. Blue colour showed no statistically significant difference with regard to the type of paint used. Brown AP showed lower ΔE than the other groups, with significant difference for OP and GP. GP showed greater alteration in ΔE for the brown colour, being statistically similar only to OP. Only the AP group for brown pigment shows clinically acceptable values for colour stability after AAA. © 2011 The Gerodontology Society and John Wiley & Sons A/S.

Reconstructing the colour palette of the Konstantinos Parthenis' burnt paintings.

PubMed

Antonopoulou-Athera, N; Chatzitheodoridis, E; Terlixi, A; Doulgerides, M; Serafetinides, A A

2018-05-09

This case study focuses on the reconstruction of the colour palette and the possibility of laser cleaning of burnt paintings. The paintings ORPHEUS IN THE UNDERWORLD and CONCORDIA, composed by the Greek artist Konstantinos Parthenis (1878-1967), have been severely damaged by fire. The colour palette of Parthenis is thoroughly investigated for the first time, and to perform this, a multi-analytical spectroscopic approach was employed. Non-destructive in situ analysis was performed on multiple areas of the paintings by portable XRF. SEM-EDS and Raman, supported by reflected visible light optical microscopy, and ultraviolet light microscopy, as well as structural XRD and molecular FTIR were performed for identifying the pigments, the binder and the substrate of the paintings. This work also unveiled new aspects of the painting technique used by the artist, such as the uncommon use of multiple pigments of red hue in the upper paint layers, comparatively with the rest of Parthenis' paintings. Molecular spectroscopic techniques (i.e., Raman and FTIR) were effective in identifying pigments like chrome yellow (crocoite mineral), chrome orange (phoenicochroite mineral) and viridian green (hydrated chromium oxide). The spectroscopic analyses were also essential in the laser cleaning restoration because of the detection of pigments (i.e., lead white, vermilion etc.) prone to phase transformations due to photothermal and/or photochemical effects. Our investigation establishes the basis on the application of non-conventional cleaning methods on damaged paintings, such as laser irradiation, in order to remove the damaged layer and/or the superficial accretions, while preserving the hues of the original painting. Copyright © 2018 Elsevier B.V. All rights reserved.

24 CFR 965.215 - Lead-based paint liability insurance coverage.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Lead-based paint liability... Insurance Coverage § 965.215 Lead-based paint liability insurance coverage. (a) General. The purpose of this... with lead-based paint activities that the PHA undertakes, in accordance with the PHA's ACC with HUD...

24 CFR 965.215 - Lead-based paint liability insurance coverage.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 4 2013-04-01 2013-04-01 false Lead-based paint liability... Insurance Coverage § 965.215 Lead-based paint liability insurance coverage. (a) General. The purpose of this... with lead-based paint activities that the PHA undertakes, in accordance with the PHA's ACC with HUD...

24 CFR 965.215 - Lead-based paint liability insurance coverage.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Lead-based paint liability... Insurance Coverage § 965.215 Lead-based paint liability insurance coverage. (a) General. The purpose of this... with lead-based paint activities that the PHA undertakes, in accordance with the PHA's ACC with HUD...

24 CFR 965.215 - Lead-based paint liability insurance coverage.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Lead-based paint liability... Insurance Coverage § 965.215 Lead-based paint liability insurance coverage. (a) General. The purpose of this... with lead-based paint activities that the PHA undertakes, in accordance with the PHA's ACC with HUD...

Library Signage: Applications for the Apple Macintosh and MacPaint.

ERIC Educational Resources Information Center

Diskin, Jill A.; FitzGerald, Patricia

1984-01-01

Describes specific applications of the Macintosh computer at Carnegie-Mellon University Libraries, where MacPaint was used as a flexible, easy to use, and powerful tool to produce informational, instructional, and promotional signage. Profiles of system hardware and software, an evaluation of the computer program MacPaint, and MacPaint signage…

24 CFR 965.215 - Lead-based paint liability insurance coverage.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Lead-based paint liability... Insurance Coverage § 965.215 Lead-based paint liability insurance coverage. (a) General. The purpose of this... with lead-based paint activities that the PHA undertakes, in accordance with the PHA's ACC with HUD...

Factors effecting paint performance on wood siding

Treesearch

Christopher G. Hunt; R. Sam Williams; Mark Knaebe; Peter Sotos; Steven Lacher

2009-01-01

Several different studies are compared to assess the effectiveness of commercial water repellent preservatives (WRP’s) in the late 1990’s on vertical and horizontal siding. Besides WRP, variables included wood species, exposure location (Wisconsin or Mississippi), and solid color stain vs. primer + paint. Data on substrate checking and paint flaking are presented....

The Sign System in Chinese Landscape Paintings

ERIC Educational Resources Information Center

McMahon, Cliff G.

2003-01-01

Paintings emerge from a culture field and must be interpreted in relation to the net of culture. A given culture will be implicated by the sign system used by the painter. Everyone agrees that in Chinese landscape paintings, the most important cultural bond is to ancient Chinese Taoism, and to a lesser degree, to Confucianism. Obviously, then, the…

THz pulsed time-domain imaging of an oil canvas painting: a case study of a painting by Pablo Picasso

NASA Astrophysics Data System (ADS)

Fukunaga, Kaori; Ikari, Tomofumi; Iwai, Kikuko

2016-02-01

The terahertz pulsed time-domain imaging technique and near-infrared observation were applied to investigate an oil painting on canvas by Pablo Picasso. The multilayer structure is clearly observed in cross-sectional image by terahertz pulsed time-domain imaging, and particular Cubism style lines were revealed under newly painted area by near-infrared image.

Characterization of Emissions of Volatile Organic Compounds from Interior Alkyd Paint.

PubMed

Fortmann, Roy; Roache, Nancy; Chang, John C S; Guo, Zhishi

1998-10-01

Alkyd paint continues to be used indoors for application to wood trim, cabinet surfaces, and some kitchen and bathroom walls. Alkyd paint may represent a significant source of volatile organic compounds (VOCs) indoors because of the frequency of use and amount of surface painted. The U.S. Environmental Protection Agency (EPA) is conducting research to characterize VOC emissions from paint and to develop source emission models that can be used for exposure assessment and risk management. The technical approach for this research involves both analysis of the liquid paint to identify and quantify the VOC contents and dynamic small chamber emissions tests to characterize the VOC emissions after application. The predominant constituents of the primer and two alkyd paints selected for testing were straight-chain alkanes (C9-C12); C8-C9 aromatics were minor constituents. Branched chain alkanes were the predominant VOCs in a third paint. A series of tests were performed to evaluate factors that may affect emissions following application of the coatings. The type of substrate (glass, wallboard, or pine board) did not have a substantial impact on the emissions with respect to peak concentrations, the emissions profile, or the amount of VOC mass emitted from the paint. Peak concentrations of total volatile organic compounds (TVOCs) as high as 10,000 mg/m 3 were measured during small chamber emissions tests at 0.5 air exchanges per hour (ACH). Over 90% of the VOCs were emitted from the primer and paints during the first 10 hr following application. Emissions were similar from paint applied to bare pine board, a primed board, or a board previously painted with the same paint. The impact of other variables, including film thickness, air velocity at the surface, and air-exchange rate (AER) were consistent with theoretical predictions for gas-phase, mass transfer-controlled emissions. In addition to the alkanes and aromatics, aldehydes were detected in the emissions during paint

Characterization of emissions of volatile organic compounds from interior alkyd paint.

PubMed

Fortmann, R; Roache, N; Chang, J C; Guo, Z

1998-10-01

Alkyd paint continues to be used indoors for application to wood trim, cabinet surfaces, and some kitchen and bathroom walls. Alkyd paint may represent a significant source of volatile organic compounds (VOCs) indoors because of the frequency of use and amount of surface painted. The U.S. Environmental Protection Agency (EPA) is conducting research to characterize VOC emissions from paint and to develop source emission models that can be used for exposure assessment and risk management. The technical approach for this research involves both analysis of the liquid paint to identify and quantify the VOC contents and dynamic small chamber emissions tests to characterize the VOC emissions after application. The predominant constituents of the primer and two alkyd paints selected for testing were straight-chain alkanes (C9-C12); C8-C9 aromatics were minor constituents. Branched chain alkanes were the predominant VOCs in a third paint. A series of tests were performed to evaluate factors that may affect emissions following application of the coatings. The type of substrate (glass, wallboard, or pine board) did not have a substantial impact on the emissions with respect to peak concentrations, the emissions profile, or the amount of VOC mass emitted from the paint. Peak concentrations of total volatile organic compounds (TVOCs) as high as 10,000 mg/m3 were measured during small chamber emissions tests at 0.5 air exchanges per hour (ACH). Over 90% of the VOCs were emitted from the primer and paints during the first 10 hr following application. Emissions were similar from paint applied to bare pine board, a primed board, or a board previously painted with the same paint. The impact of other variable, including film thickness, air velocity at the surface, and air-exchange rate (AER) were consistent with theoretical predictions for gas-phase, mass transfer-controlled emissions. In addition to the alkanes and aromatics, aldehydes were detected in the emissions during paint

Vacuum Plasma Spraying Replaces Electrodeposition

NASA Technical Reports Server (NTRS)

Holmes, Richard R.; Power, Chris; Burns, David H.; Daniel, Ron; Mckechnie, Timothy N.

1992-01-01

Vacuum plasma spraying used to fabricate large parts with complicated contours and inner structures, without uninspectable welds. Reduces time, and expense of fabrication. Wall of combustion chamber built up inside of outer nickel-alloy jacket by plasma spraying. Particles of metal sprayed partially melted in plasma gun and thrown at supersonic speed toward deposition surface. Vacuum plasma-spray produces stronger bond between the grooves and covering layer completing channels and wall of combustion chamber. In tests, bond withstood pressure of 20 kpsi, three times allowable limit by old method.

Atomic Oxygen Treatment Technique for Removal of Smoke Damage from Paintings

NASA Technical Reports Server (NTRS)

Rutledge, S. K.; Banks, B. A.

1997-01-01

Soot deposits that can accumulate on surfaces of a painting during a fire can be difficult to clean from some types of paintings without damaging the underlying paint layers. A non-contact technique has been developed which can remove the soot by allowing a gas containing atomic oxygen to flow over the surface and chemically react with the soot to form carbon monoxide and carbon dioxide. The reaction is limited to the surface, so the underlying paint is not touched. The process can be controlled so that the cleaning can be stopped once the paint surface is reached. This paper describes the smoke exposure and cleaning of untreated canvas, acrylic gesso, and sections of an oil painting using this technique. The samples were characterized by optical microscopy and reflectance spectroscopy.

Terahertz reflection interferometry for automobile paint layer thickness measurement

NASA Astrophysics Data System (ADS)

Rahman, Aunik; Tator, Kenneth; Rahman, Anis

2015-05-01

Non-destructive terahertz reflection interferometry offers many advantages for sub-surface inspection such as interrogation of hidden defects and measurement of layers' thicknesses. Here, we describe a terahertz reflection interferometry (TRI) technique for non-contact measurement of paint panels where the paint is comprised of different layers of primer, basecoat, topcoat and clearcoat. Terahertz interferograms were generated by reflection from different layers of paints on a metallic substrate. These interferograms' peak spacing arising from the delay-time response of respective layers, allow one to model the thicknesses of the constituent layers. Interferograms generated at different incident angles show that the interferograms are more pronounced at certain angles than others. This "optimum" angle is also a function of different paint and substrate combinations. An automated angular scanning algorithm helps visualizing the evolution of the interferograms as a function of incident angle and also enables the identification of optimum reflection angle for a given paint-substrate combination. Additionally, scanning at different points on a substrate reveals that there are observable variations from one point to another of the same sample over its entire surface area. This ability may be used as a quality control tool for in-situ inspection in a production line. Keywords: Terahertz reflective interferometry, Paint and coating layers, Non-destructive

A Method to Predict the Thickness of Poorly-Bonded Material Along Spray and Spray-Layer Boundaries in Cold Spray Deposition

NASA Astrophysics Data System (ADS)

Li, Yangfan; Hamada, Yukitaka; Otobe, Katsunori; Ando, Teiichi

2017-02-01

Multi-traverse CS provides a unique means for the production of thick coatings and bulk materials from powders. However, the material along spray and spray-layer boundaries is often poorly bonded as it is laid by the leading and trailing peripheries of the spray that carry powder particles with insufficient kinetic energy. For the same reason, the splats in the very first layer deposited on the substrate may not be bonded well either. A mathematical spray model was developed based on an axisymmetric Gaussian mass flow rate distribution and a stepped deposition yield to predict the thickness of such poorly-bonded layers in multi-traverse CS deposition. The predicted thickness of poorly-bonded layers in a multi-traverse Cu coating falls in the range of experimental values. The model also predicts that the material that contains poorly bonded splats could exceed 20% of the total volume of the coating.

Numerical Studies of High-Intensity Injection Painting for Project X

DOE Office of Scientific and Technical Information (OSTI.GOV)

Drozhdin, A.I.; Vorobiev, L.G.; Johnson, D.E.

Injection phase space painting enables the mitigation of space charge and stability issues, and will be indispensable for the Project-X at Fermilab [1], delivering high-intensity proton beams to HEP experiments. Numerical simulations of multi-turn phase space painting have been performed for the FNAL Recycler Ring, including a self-consistent space charge model. The goal of our studies was to study the injection painting with inclusion of 3D space charge, using the ORBIT tracking code. In a current scenario the painting lasts for 110 turns, twice faster, than we considered in this paper. The optimal wave-forms for painting kickers, which ensure themore » flatter phase distributions, should be found. So far we used a simplified model for painting kicker strength (implemented as the 'ideal bump' in ORBIT). We will include a more realistic field map for the chicane magnets. Additional stripping simulations will be combined. We developed a block for longitudinal painting, which works with arbitrary notches in incoming micro-bunch buckets. The appropriate choice of the amplitude of the second harmonic of RF field will help to flatten the RF-bucket contours, as was demonstrated in 1D simulations. Non-linear lattice issue will be also addressed.« less

Polling booth surveys: a novel approach for reducing social desirability bias in HIV-related behavioural surveys in resource-poor settings.

PubMed

Lowndes, Catherine M; Jayachandran, A A; Banandur, Pradeep; Ramesh, Banadakoppa M; Washington, Reynold; Sangameshwar, B M; Moses, Stephen; Blanchard, James; Alary, Michel

2012-05-01

This study compared rates of HIV-related sexual risk behaviours reported in individual face-to-face (FTFI) and group anonymous polling booth (PBS) interviews in India. In PBS, respondents grouped by gender and marital status answered yes/no questions by putting tokens with question numbers in colour-coded containers. Data were subsequently collated for each group as a whole, so responses were not traceable back to individuals. Male and female PBS participants reported substantially higher rates of pre-marital, extra-marital, commercial and anal sex than FTFI participants; e.g. 11 vs. 2% married males reported paying for sex; 6 vs. 1% unmarried males reported homosexual anal sex.

46 CFR 111.105-43 - Paint stowage or mixing spaces.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Paint stowage or mixing spaces. 111.105-43 Section 111... ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Hazardous Locations § 111.105-43 Paint stowage or mixing spaces. A space for the stowage or mixing of paint must not have any electric equipment, except: (a) Intrinsically...

46 CFR 111.105-43 - Paint stowage or mixing spaces.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Paint stowage or mixing spaces. 111.105-43 Section 111... ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Hazardous Locations § 111.105-43 Paint stowage or mixing spaces. A space for the stowage or mixing of paint must not have any electric equipment, except: (a) Intrinsically...

46 CFR 111.105-43 - Paint stowage or mixing spaces.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Paint stowage or mixing spaces. 111.105-43 Section 111... ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Hazardous Locations § 111.105-43 Paint stowage or mixing spaces. A space for the stowage or mixing of paint must not have any electric equipment, except: (a) Intrinsically...

24 CFR 291.430 - Elimination of lead-based paint hazards.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 2 2012-04-01 2012-04-01 false Elimination of lead-based paint... Lease and Sale of HUD-Acquired Single Family Properties for the Homeless § 291.430 Elimination of lead-based paint hazards. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the...

24 CFR 291.430 - Elimination of lead-based paint hazards.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 2 2013-04-01 2013-04-01 false Elimination of lead-based paint... Lease and Sale of HUD-Acquired Single Family Properties for the Homeless § 291.430 Elimination of lead-based paint hazards. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the...

24 CFR 291.430 - Elimination of lead-based paint hazards.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 2 2011-04-01 2011-04-01 false Elimination of lead-based paint... Lease and Sale of HUD-Acquired Single Family Properties for the Homeless § 291.430 Elimination of lead-based paint hazards. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the...

24 CFR 291.430 - Elimination of lead-based paint hazards.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 24 Housing and Urban Development 2 2014-04-01 2014-04-01 false Elimination of lead-based paint... Lease and Sale of HUD-Acquired Single Family Properties for the Homeless § 291.430 Elimination of lead-based paint hazards. The Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the...

46 CFR 111.105-43 - Paint stowage or mixing spaces.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Paint stowage or mixing spaces. 111.105-43 Section 111... ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Hazardous Locations § 111.105-43 Paint stowage or mixing spaces. A space for the stowage or mixing of paint must not have any electric equipment, except: (a) Intrinsically...