Information Science Panel joint meeting with Imaging Science Panel

NASA Technical Reports Server (NTRS)

1982-01-01

Specific activity in information extraction science (taken to include data handling) is needed to: help identify the bounds of practical missions; identify potential data handling and analysis scenarios; identify the required enabling technology; and identify the requirements for a design data base to be used by the disciplines in determining potential parameters for future missions. It was defined that specific analysis topics were a function of the discipline involved, and therefore no attempt was made to define any specific analysis developments required. Rather, it was recognized that a number of generic data handling requirements exist whose solutions cannot be typically supported by the disciplines. The areas of concern were therefore defined as: data handling aspects of system design considerations; enabling technology for data handling, with specific attention to rectification and registration; and enabling technology for analysis. Within each of these areas, the following topics were addressed: state of the art (current status and contributing factors); critical issues; and recommendations for research and/or development.

76 FR 48073 - Hazardous Waste Management System: Identification and Listing of Hazardous Waste: Carbon Dioxide...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-08

... Science Basis. Contribution of Working Group I to the Fourth Assessment Report of the Intergovernmental Panel on Climate Change [Solomon, S., D. Qin, M. Manning, Z. Chen, M. Marquis, K.B. Averyt, M. Tignor... Vulnerability. Contribution of Working Group II to the Fourth Assessment Report of the Intergovernmental Panel...

NAS Panel endorses science center concept

NASA Astrophysics Data System (ADS)

Science and technology centers, as proposed by President Ronald Reagan in his January 1987 State of the Union message, could make “significant contributions to science and to the nation's economic competitiveness,” according to a new report by a National Academy of Sciences (NAS) panel. What will be necessary to realize these contributions, the panel cautioned, are proper management, adequate resources, and, “above all, the selection of programs for which the centers are the most effective form of organization.”NSF plans to support science and technology centers, beginning October 1, 1988, which is the start of fiscal year 1988. NSF requested guidance from the NAS panel in implementing the program. Although other government agencies will participate in the program, NSF will play the primary role.

Yield and cost of individual common diagnostic tests in new primary care outpatients in Japan.

PubMed

Takemura, Yuzuru; Ishida, Haku; Inoue, Yuji; Beck, J Robert

2002-01-01

Appropriate diagnostic testing involves considerations of cost-effectiveness. We examined the cost-effectiveness of individual tests in a panel of tests defined by the Japan Society of Clinical Pathology. We studied 540 new, symptomatic primary care outpatients with a set of 30 common diagnostic tests [the Essential Laboratory Tests (2); ELT(2) panel] for clinical evaluation and identification of occult disease. A useful result (UR) of testing was defined as a finding that contributed to a change in a physician's diagnosis or decision-making relating to a "tentative initial diagnosis" obtained from history and physical examination alone. The ELT(2) panel testing yielded 398 URs and uncovered 261 occult diseases among 540 patients. In total, 1592 tests contributed to either UR-generation or discovery of occult disease. The cost per effective test (cost required per test that contributed to either definition of effectiveness) ranged from 108 yen (approximately 0.92 US dollars) for total cholesterol to 6200 yen (approximately 52.50 dollars) for chest x-ray. Contribution rates and the cost per effective test varied among disease categories. We restructured panel components considering the effectiveness of each test. Subsets of the ELT(2) would have improved cost-effectiveness and achieved cost savings in five of eight disease categories. Assembly of tests based on cost-effectiveness can improve clinical efficiency and decrease total cost of panel testing for selected patient groups.

A method for the geometrically nonlinear analysis of compressively loaded prismatic composite structures

NASA Technical Reports Server (NTRS)

Stoll, Frederick; Gurdal, Zafer; Starnes, James H., Jr.

1991-01-01

A method was developed for the geometrically nonlinear analysis of the static response of thin-walled stiffened composite structures loaded in uniaxial or biaxial compression. The method is applicable to arbitrary prismatic configurations composed of linked plate strips, such as stiffened panels and thin-walled columns. The longitudinal ends of the structure are assumed to be simply supported, and geometric shape imperfections can be modeled. The method can predict the nonlinear phenomena of postbuckling strength and imperfection sensitivity which are exhibited by some buckling-dominated structures. The method is computer-based and is semi-analytic in nature, making it computationally economical in comparison to finite element methods. The method uses a perturbation approach based on the use of a series of buckling mode shapes to represent displacement contributions associated with nonlinear response. Displacement contributions which are of second order in the model amplitudes are incorported in addition to the buckling mode shapes. The principle of virtual work is applied using a finite basis of buckling modes, and terms through the third order in the model amplitudes are retained. A set of cubic nonlinear algebraic equations are obtained, from which approximate equilibrium solutions are determined. Buckling mode shapes for the general class of structure are obtained using the VIPASA analysis code within the PASCO stiffened-panel design code. Thus, subject to some additional restrictions in loading and plate anisotropy, structures which can be modeled with respect to buckling behavior by VIPASA can be analyzed with respect to nonlinear response using the new method. Results obtained using the method are compared with both experimental and analytical results in the literature. The configurations investigated include several different unstiffened and blade-stiffening panel configurations, featuring both homogeneous, isotropic materials, and laminated composite material.

Panel discussion: The future of IR astronomy

NASA Technical Reports Server (NTRS)

Caroff, Lawrence J.

1995-01-01

A panel discussion was held on the future of IR astronomy. The chairman gave a brief introduction to current planned programs for NASA and other space agencies, followed by short contributions from the six panel members on a variety of special topics. After that, a short question and answer session was held.

A Comparative Study of the Perceptions of Professional Staff on Their Contribution to Student Outcomes

ERIC Educational Resources Information Center

Regan, Julie-Anne; Dollard, Emma; Banks, Nicci

2014-01-01

This study examined the perceptions of professional staff on their contribution to student outcomes. An online Delphi survey method was used to collect data from two expert panels: professional staff based in faculties and professional staff based in central university departments. The aim of this method is for the panels to reach consensus. The…

Analysis of anthropogenic contributions to record high Australian summer rainfall (2010-2012) using CMIP5 simulations

NASA Astrophysics Data System (ADS)

Lewis, Sophie; Karoly, David

2013-04-01

Changes in extreme climate events pose significant challenges for both human and natural systems. Some climate extremes are likely to become "more frequent, more widespread and/or more intense during the 21st century" (Intergovernmental Panel on Climate Change, 2007) due to anthropogenic climate change. Particularly in Australia, El Niño-Southern Oscillation (ENSO) has a relationship to the relative frequency of temperature and precipitation extremes. In this study, we investigate the record high two-summer rainfall observed in Australia (2010-2011 and 2011-2012). This record rainfall occurred in association with a two year extended La Niña event and resulted in severe and extensive flooding. We examine simulated changes in seasonal-scale rainfall extremes in the Australian region in a suite of models participating in the Coupled Model Intercomparison Project Phase 5 (CMIP5). In particular, we utilise the novel CMIP5 detection and attribution historical experiments with various forcings (natural forcings only and greenhouse gas forcings only) to examine the impact of various anthropogenic forcings on seasonal-scale extreme rainfall across Australia. Using these standard detection and attribution experiments over the period of 1850 to 2005, we examine La Niña contributions to the 2-season record rainfall, as well as the longer-term climate change contribution to rainfall extremes. Was there an anthropogenic influence in the record high Australian summer rainfall over 2010 to 2012, and if so, how much influence? Intergovernmental Panel on Climate Change (2007), Climate Change 2007: The Physical Science Basis, Contribution of Working Group I to the Fourth Assessment Report on the Intergovernmental Panel on Climate Change, edited by S. Solomon et al., 996 pp., Cambridge Univ. Press, Cambridge, U. K.

Heave and Flow: Understanding the role of resonance and shape evolution for heaving flexible panels

NASA Astrophysics Data System (ADS)

Hoover, Alexander; Cortez, Ricardo; Tytell, Eric; Fauci, Lisa

2017-11-01

Many animals that swim or fly use their body to accelerate the fluid around them, transferring momentum from their bodies to the surrounding fluid. The emergent kinematics from this transfer are a result of the coupling between the fluid and the material properties of the body. Here we present a computational study of a 3-dimensional flexible panel that is heaved at its leading edge in an incompressible, viscous fluid. These high-fidelity numerical simulations enable us to examine the role of resonance, fluid forces, and panel deformations have on swimming performance. Varying both the passive material properties and the heaving frequency of the panel, we find peaks in trailing edge amplitude and forward swimming speed are determined by a dimensionless quantity, the effective flexibility. Modal decompositions of panel deflections reveal that the strength of each mode is related to the effective flexibility and peaks in the swimming speed and trailing edge amplitude correspond to peaks in the contributions of different modes. Panels of different material properties but with similar effective flexibilities have modal contributions that evolve similarly over the phase of the heaving cycle and agreement in dominant vortex structures generated by the panel. NSF RTG 1043626.

Environmental Performance of North American Wood Panel Manufacturing

Treesearch

R. Bergman; D. Kaestner; A. Taylor

2015-01-01

Manufacturing building products such as wood panels has environmental impacts, including contributions to climate change. This paper is a compilation of four studies quantifying these impacts using the life-cycle assessment (LCA) method on five wood-based panel products made in North America during 2012. LCA is an internationally accepted and standardized method for...

Life cycle impacts of North American wood panel Manufacturing

Treesearch

Richard Bergman; D. Kaestner; A. M. Taylor

2016-01-01

Manufacturing building products such as wood panels impacts the environment, including contributing to climate change. This study is a compilation of four studies quantifying these impacts using the life cycle assessment (LCA) method on five wood-based panel products made in North America during 2012. LCA is an internationally accepted and standardized method for...

Male reproductive disorders, diseases, and costs of exposure to endocrine-disrupting chemicals in the European Union.

PubMed

Hauser, Russ; Skakkebaek, Niels E; Hass, Ulla; Toppari, Jorma; Juul, Anders; Andersson, Anna Maria; Kortenkamp, Andreas; Heindel, Jerrold J; Trasande, Leonardo

2015-04-01

Increasing evidence suggests that endocrine-disrupting chemicals (EDCs) contribute to male reproductive diseases and disorders. To estimate the incidence/prevalence of selected male reproductive disorders/diseases and associated economic costs that can be reasonably attributed to specific EDC exposures in the European Union (EU). An expert panel evaluated evidence for probability of causation using the Intergovernmental Panel on Climate Change weight-of-evidence characterization. Exposure-response relationships and reference levels were evaluated, and biomarker data were organized from carefully identified studies from the peer-reviewed literature to represent European exposure and approximate burden of disease as it occurred in 2010. The cost-of-illness estimation utilized multiple peer-reviewed sources. The expert panel identified low epidemiological and strong toxicological evidence for male infertility attributable to phthalate exposure, with a 40-69% probability of causing 618,000 additional assisted reproductive technology procedures, costing €4.71 billion annually. Low epidemiological and strong toxicological evidence was also identified for cryptorchidism due to prenatal polybrominated diphenyl ether exposure, resulting in a 40-69% probability that 4615 cases result, at a cost of €130 million (sensitivity analysis, €117-130 million). A much more modest (0-19%) probability of causation in testicular cancer by polybrominated diphenyl ethers was identified due to very low epidemiological and weak toxicological evidence, with 6830 potential cases annually and costs of €848 million annually (sensitivity analysis, €313-848 million). The panel assigned 40-69% probability of lower T concentrations in 55- to 64-year-old men due to phthalate exposure, with 24 800 associated deaths annually and lost economic productivity of €7.96 billion. EDCs may contribute substantially to male reproductive disorders and diseases, with nearly €15 billion annual associated costs in the EU. These estimates represent only a few EDCs for which there were sufficient epidemiological studies and those with the highest probability of causation. These public health costs should be considered as the EU contemplates regulatory action on EDCs.

Sound transmission loss of composite sandwich panels

NASA Astrophysics Data System (ADS)

Zhou, Ran

Light composite sandwich panels are increasingly used in automobiles, ships and aircraft, because of the advantages they offer of high strength-to-weight ratios. However, the acoustical properties of these light and stiff structures can be less desirable than those of equivalent metal panels. These undesirable properties can lead to high interior noise levels. A number of researchers have studied the acoustical properties of honeycomb and foam sandwich panels. Not much work, however, has been carried out on foam-filled honeycomb sandwich panels. In this dissertation, governing equations for the forced vibration of asymmetric sandwich panels are developed. An analytical expression for modal densities of symmetric sandwich panels is derived from a sixth-order governing equation. A boundary element analysis model for the sound transmission loss of symmetric sandwich panels is proposed. Measurements of the modal density, total loss factor, radiation loss factor, and sound transmission loss of foam-filled honeycomb sandwich panels with different configurations and thicknesses are presented. Comparisons between the predicted sound transmission loss values obtained from wave impedance analysis, statistical energy analysis, boundary element analysis, and experimental values are presented. The wave impedance analysis model provides accurate predictions of sound transmission loss for the thin foam-filled honeycomb sandwich panels at frequencies above their first resonance frequencies. The predictions from the statistical energy analysis model are in better agreement with the experimental transmission loss values of the sandwich panels when the measured radiation loss factor values near coincidence are used instead of the theoretical values for single-layer panels. The proposed boundary element analysis model provides more accurate predictions of sound transmission loss for the thick foam-filled honeycomb sandwich panels than either the wave impedance analysis model or the statistical energy analysis model.

Blue Ribbon Panel Report

Cancer.gov

An NCI Cancer Currents blog by the NCI acting director thanking the cancer community for contributing to the Cancer Moonshot Blue Ribbon Panel report, which was presented to the National Cancer Advisory Board on September 7.

An efficient iterative model reduction method for aeroviscoelastic panel flutter analysis in the supersonic regime

NASA Astrophysics Data System (ADS)

Cunha-Filho, A. G.; Briend, Y. P. J.; de Lima, A. M. G.; Donadon, M. V.

2018-05-01

The flutter boundary prediction of complex aeroelastic systems is not an easy task. In some cases, these analyses may become prohibitive due to the high computational cost and time associated with the large number of degrees of freedom of the aeroelastic models, particularly when the aeroelastic model incorporates a control strategy with the aim of suppressing the flutter phenomenon, such as the use of viscoelastic treatments. In this situation, the use of a model reduction method is essential. However, the construction of a modal reduction basis for aeroviscoelastic systems is still a challenge, owing to the inherent frequency- and temperature-dependent behavior of the viscoelastic materials. Thus, the main contribution intended for the present study is to propose an efficient and accurate iterative enriched Ritz basis to deal with aeroviscoelastic systems. The main features and capabilities of the proposed model reduction method are illustrated in the prediction of flutter boundary for a thin three-layer sandwich flat panel and a typical aeronautical stiffened panel, both under supersonic flow.

Testing consumer perception of nutrient content claims using conjoint analysis.

PubMed

Drewnowski, Adam; Moskowitz, Howard; Reisner, Michele; Krieger, Bert

2010-05-01

The US Food and Drug Administration (FDA) proposes to establish standardized and mandatory criteria upon which front-of-pack (FOP) nutrition labelling must be based. The present study aimed to estimate the relative contribution of declared amounts of different nutrients to the perception of the overall 'healthfulness' of foods by the consumer. Protein, fibre, vitamin A, vitamin C, calcium and iron were nutrients to encourage. Total fat, saturated fat, cholesterol, total and added sugar, and sodium were the nutrients to limit. Two content claims per nutrient used the FDA-approved language. An online consumer panel (n 320) exposed to multiple messages (n 48) rated the healthfulness of each hypothetical food product. Utility functions were constructed using conjoint analysis, based on multiple logistic regression and maximum likelihood estimation. Consumer perception of healthfulness was most strongly driven by the declared presence of protein, fibre, calcium and vitamin C and by the declared total absence of saturated fat and sodium. For this adult panel, total and added sugar had lower utilities and contributed less to the perception of healthfulness. There were major differences between women and men. Conjoint analysis can lead to a better understanding of how consumers process information about the full nutrition profile of a product, and is a powerful tool for the testing of nutrient content claims. Such studies can help the FDA develop science-based criteria for nutrient profiling that underlies FOP and shelf labelling.

Carbon emissions, logistics volume and GDP in China: empirical analysis based on panel data model.

PubMed

Guo, Xiaopeng; Ren, Dongfang; Shi, Jiaxing

2016-12-01

This paper studies the relationship among carbon emissions, GDP, and logistics by using a panel data model and a combination of statistics and econometrics theory. The model is based on the historical data of 10 typical provinces and cities in China during 2005-2014. The model in this paper adds the variability of logistics on the basis of previous studies, and this variable is replaced by the freight turnover of the provinces. Carbon emissions are calculated by using the annual consumption of coal, oil, and natural gas. GDP is the gross domestic product. The results showed that the amount of logistics and GDP have a contribution to carbon emissions and the long-term relationships are different between different cities in China, mainly influenced by the difference among development mode, economic structure, and level of logistic development. After the testing of panel model setting, this paper established a variable coefficient model of the panel. The influence of GDP and logistics on carbon emissions is obtained according to the influence factors among the variables. The paper concludes with main findings and provides recommendations toward rational planning of urban sustainable development and environmental protection for China.

A Selected Immunohistochemical Panel Aids in Differential Diagnosis and Prognostic Stratification of Subtypes of High-grade Endometrial Carcinoma: A Clinicopathologic and Immunohistochemical Study at a Single Institution.

PubMed

Taskin, Orhun Çiğ; Onder, Semen; Topuz, Samet; Sozen, Hamdullah; Sen, Fatma; Ilhan, Ridvan; Yavuz, Ekrem

This study aimed to investigate whether a selected immunohistochemical panel (estrogen receptor, p53, ARID1A, PPP2R1A, HNF-1β) could contribute to the diagnostic process of high-grade endometrial carcinomas (HG-ECs). We also aimed to analyze the correlation of these immunohistochemical results with several morphologic variables and survival data. After revising the diagnosis of 78 HG-ECs, immunohistochemical analysis was performed for each case. After immunohistochemical analysis, a specific diagnosis of prototypic HG-EC was established in most of the cases that were uncertain due to morphologic ambiguity. In the univariate analysis, older patient age, type II morphology, undifferentiated carcinoma and carcinosarcoma type of histology, altered p53 immunostaining, strong membranous staining of PPP2R1A, presence of lymphovascular invasion in serous carcinoma, and microcystic, elongated, and fragmented-type infiltration pattern in endometrioid carcinoma were significantly related to poor prognosis. In the multivariate analysis, only older patient age and carcinosarcoma or undifferentiated/dedifferentiated carcinoma type histology were found to be significantly poor prognostic factors (P=0.011), whereas advanced FIGO stage and type II histology were found to be correlated with poor prognosis, but did not reach statistical significance. We suggest that immunohistochemistry should be used in the differential diagnosis of HG-ECs, especially those with ambiguous morphology. Markers used in this study made a valuable contribution to the diagnostic process as well as prediction of prognosis.

A financial network perspective of financial institutions' systemic risk contributions

NASA Astrophysics Data System (ADS)

Huang, Wei-Qiang; Zhuang, Xin-Tian; Yao, Shuang; Uryasev, Stan

2016-08-01

This study considers the effects of the financial institutions' local topology structure in the financial network on their systemic risk contribution using data from the Chinese stock market. We first measure the systemic risk contribution with the Conditional Value-at-Risk (CoVaR) which is estimated by applying dynamic conditional correlation multivariate GARCH model (DCC-MVGARCH). Financial networks are constructed from dynamic conditional correlations (DCC) with graph filtering method of minimum spanning trees (MSTs). Then we investigate dynamics of systemic risk contributions of financial institution. Also we study dynamics of financial institution's local topology structure in the financial network. Finally, we analyze the quantitative relationships between the local topology structure and systemic risk contribution with panel data regression analysis. We find that financial institutions with greater node strength, larger node betweenness centrality, larger node closeness centrality and larger node clustering coefficient tend to be associated with larger systemic risk contributions.

Effects of employer-sponsored health insurance costs on Social Security taxable wages.

PubMed

Burtless, Gary; Milusheva, Sveta

2013-01-01

The increasing cost of employer contributions for employee health insurance reduces the share of compensation subject to the Social Security payroll tax. Rising insurance contributions can also have a more subtle effect on the Social Security tax base because they influence the distribution of money wages above and below the taxable maximum amount. This article uses the Medical Expenditure Panel Survey to analyze trends in employer health insurance contributions and the distribution of those costs up and down the wage distribution. Our analysis shows that employer health insurance contributions increased faster than overall compensation during 1996-2008, but such contributions grew only slightly faster among workers earning less than the taxable maximum than they did among those earning more. Because employer health insurance contributions represent a much higher percentage of compensation below the taxable maximum, health insurance cost trends exerted a disproportionate downward pressure on money wages below the taxable maximum.

Expression of PAM50 Genes in Lung Cancer: Evidence that Interactions between Hormone Receptors and HER2/HER3 Contribute to Poor Outcome.

PubMed

Siegfried, Jill M; Lin, Yan; Diergaarde, Brenda; Lin, Hui-Min; Dacic, Sanja; Pennathur, Arjun; Weissfeld, Joel L; Romkes, Marjorie; Nukui, Tomoko; Stabile, Laura P

2015-11-01

Non-small cell lung cancers (NSCLCs) frequently express estrogen receptor (ER) β, and estrogen signaling is active in many lung tumors. We investigated the ability of genes contained in the prediction analysis of microarray 50 (PAM50) breast cancer risk predictor gene signature to provide prognostic information in NSCLC. Supervised principal component analysis of mRNA expression data was used to evaluate the ability of the PAM50 panel to provide prognostic information in a stage I NSCLC cohort, in an all-stage NSCLC cohort, and in The Cancer Genome Atlas data. Immunohistochemistry was used to determine status of ERβ and other proteins in lung tumor tissue. Associations with prognosis were observed in the stage I cohort. Cross-validation identified seven genes that, when analyzed together, consistently showed survival associations. In pathway analysis, the seven-gene panel described one network containing the ER and progesterone receptor, as well as human epidermal growth factor receptor (HER)2/HER3 and neuregulin-1. NSCLC cases also showed a significant association between ERβ and HER2 protein expression. Cases positive for HER2 expression were more likely to express HER3, and ERβ-positive cases were less likely to be both HER2 and HER3 negative. Prognostic ability of genes in the PAM50 panel was verified in an ERβ-positive cohort representing all NSCLC stages. In The Cancer Genome Atlas data sets, the PAM50 gene set was prognostic in both adenocarcinoma and squamous cell carcinoma, whereas the seven-gene panel was prognostic only in squamous cell carcinoma. Genes in the PAM50 panel, including those linking ER and HER2, identify lung cancer patients at risk for poor outcome, especially among ERβ-positive cases and squamous cell carcinoma. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Sensitivity of BRCA1/2 testing in high-risk breast/ovarian/male breast cancer families: little contribution of comprehensive RNA/NGS panel testing.

PubMed

Byers, Helen; Wallis, Yvonne; van Veen, Elke M; Lalloo, Fiona; Reay, Kim; Smith, Philip; Wallace, Andrew J; Bowers, Naomi; Newman, William G; Evans, D Gareth

2016-11-01

The sensitivity of testing BRCA1 and BRCA2 remains unresolved as the frequency of deep intronic splicing variants has not been defined in high-risk familial breast/ovarian cancer families. This variant category is reported at significant frequency in other tumour predisposition genes, including NF1 and MSH2. We carried out comprehensive whole gene RNA analysis on 45 high-risk breast/ovary and male breast cancer families with no identified pathogenic variant on exonic sequencing and copy number analysis of BRCA1/2. In addition, we undertook variant screening of a 10-gene high/moderate risk breast/ovarian cancer panel by next-generation sequencing. DNA testing identified the causative variant in 50/56 (89%) breast/ovarian/male breast cancer families with Manchester scores of ≥50 with two variants being confirmed to affect splicing on RNA analysis. RNA sequencing of BRCA1/BRCA2 on 45 individuals from high-risk families identified no deep intronic variants and did not suggest loss of RNA expression as a cause of lost sensitivity. Panel testing in 42 samples identified a known RAD51D variant, a high-risk ATM variant in another breast ovary family and a truncating CHEK2 mutation. Current exonic sequencing and copy number analysis variant detection methods of BRCA1/2 have high sensitivity in high-risk breast/ovarian cancer families. Sequence analysis of RNA does not identify any variants undetected by current analysis of BRCA1/2. However, RNA analysis clarified the pathogenicity of variants of unknown significance detected by current methods. The low diagnostic uplift achieved through sequence analysis of the other known breast/ovarian cancer susceptibility genes indicates that further high-risk genes remain to be identified.

Genomic Sequencing Procedure Microcosting Analysis and Health Economic Cost-Impact Analysis: A Report of the Association for Molecular Pathology.

PubMed

Sabatini, Linda M; Mathews, Charles; Ptak, Devon; Doshi, Shivang; Tynan, Katherine; Hegde, Madhuri R; Burke, Tara L; Bossler, Aaron D

2016-05-01

The increasing use of advanced nucleic acid sequencing technologies for clinical diagnostics and therapeutics has made vital understanding the costs of performing these procedures and their value to patients, providers, and payers. The Association for Molecular Pathology invested in a cost and value analysis of specific genomic sequencing procedures (GSPs) newly coded by the American Medical Association Current Procedural Terminology Editorial Panel. Cost data and work effort, including the development and use of data analysis pipelines, were gathered from representative laboratories currently performing these GSPs. Results were aggregated to generate representative cost ranges given the complexity and variability of performing the tests. Cost-impact models for three clinical scenarios were generated with assistance from key opinion leaders: impact of using a targeted gene panel in optimizing care for patients with advanced non-small-cell lung cancer, use of a targeted gene panel in the diagnosis and management of patients with sensorineural hearing loss, and exome sequencing in the diagnosis and management of children with neurodevelopmental disorders of unknown genetic etiology. Each model demonstrated value by either reducing health care costs or identifying appropriate care pathways. The templates generated will aid laboratories in assessing their individual costs, considering the value structure in their own patient populations, and contributing their data to the ongoing dialogue regarding the impact of GSPs on improving patient care. Copyright © 2016 American Society for Investigative Pathology and the Association for Molecular Pathology. Published by Elsevier Inc. All rights reserved.

ISPAN (Interactive Stiffened Panel Analysis): A tool for quick concept evaluation and design trade studies

NASA Technical Reports Server (NTRS)

Hairr, John W.; Dorris, William J.; Ingram, J. Edward; Shah, Bharat M.

1993-01-01

Interactive Stiffened Panel Analysis (ISPAN) modules, written in FORTRAN, were developed to provide an easy to use tool for creating finite element models of composite material stiffened panels. The modules allow the user to interactively construct, solve and post-process finite element models of four general types of structural panel configurations using only the panel dimensions and properties as input data. Linear, buckling and post-buckling solution capability is provided. This interactive input allows rapid model generation and solution by non finite element users. The results of a parametric study of a blade stiffened panel are presented to demonstrate the usefulness of the ISPAN modules. Also, a non-linear analysis of a test panel was conducted and the results compared to measured data and previous correlation analysis.

Transient Thermal Testing and Analysis of a Thermally Insulating Structural Sandwich Panel

NASA Technical Reports Server (NTRS)

Blosser, Max L.; Daryabeigi, Kamran; Bird, Richard K.; Knutson, Jeffrey R.

2015-01-01

A core configuration was devised for a thermally insulating structural sandwich panel. Two titanium prototype panels were constructed to illustrate the proposed sandwich panel geometry. The core of one of the titanium panels was filled with Saffil(trademark) alumina fibrous insulation and the panel was tested in a series of transient thermal tests. Finite element analysis was used to predict the thermal response of the panel using one- and two-dimensional models. Excellent agreement was obtained between predicted and measured temperature histories.

Computational and experimental studies of microvascular void features for passive-adaptation of structural panel dynamic properties

NASA Astrophysics Data System (ADS)

Sears, Nicholas C.; Harne, Ryan L.

2018-01-01

The performance, integrity, and safety of built-up structural systems are critical to their effective employment in diverse engineering applications. In conflict with these goals, harmonic or random excitations of structural panels may promote large amplitude oscillations that are particularly harmful when excitation energies are concentrated around natural frequencies. This contributes to fatigue concerns, performance degradation, and failure. While studies have considered active or passive damping treatments that adapt material characteristics and configurations for structural control, it remains to be understood how vibration properties of structural panels may be tailored via internal material transitions. Motivated to fill this knowledge gap, this research explores an idea of adapting the static and dynamic material distribution of panels through embedded microvascular channels and strategically placed voids that permit the internal movement of fluids within the panels for structural dynamic control. Finite element model and experimental investigations probe how redistributing material in the form of microscale voids influences the global vibration modes and natural frequencies of structural panels. Through parameter studies, the relationships among void shape, number, size, and location are quantified towards their contribution to the changing structural dynamics. For the panel composition and boundary conditions considered in this report, the findings reveal that transferring material between strategically placed voids may result in eigenfrequency changes as great as 10.0, 5.0, and 7.4% for the first, second, and third modes, respectively.

A panel analysis of the strategic association between information and communication technology and public health delivery.

PubMed

Wu, Sarah Jinhui; Raghupathi, Wullianallur

2012-10-22

In this exploratory research, we use panel data analysis to examine the correlation between Information and Communication Technology (ICTs) and public health delivery at the country level. The goal of this exploratory research is to examine the strategic association over time between ICTs and country-level public health. Using data from the World Development Indicators, we construct a panel data set of countries of five different income levels and look closely at the period from 2000 to 2008. The panel data analysis allows us to explore this dynamic relationship under the control for unobserved country-specific effects by using a fixed-effects estimation method. In particular,, we examine the association of five ICT factors with five public health indicators: adolescent fertility rate, child immunization coverage, tuberculosis case detected, life expectancy, and adult mortality rate. First, overall ICTs' factors substantially improve a country's public health delivery on the top of wealth effect. Second, among all the ICTs' factors, accessibility is the only one that is associated with improvements in all aspects of public health delivery, while the contributions from the usage, quality, and applications are negligible. ICTs' accessibility factor is associated with a considerable extension to life expectancy and reduced adult mortality rate. Third, all entity-specific factors are significant in each model, indicating that countries' economic development level does influence their public health delivery. Our results indicate that ICT accessibility has a strong association with effective delivery of public health. There are others, but the key strategic applications are eHealth and mHealth. The findings of this study will help government officials and public health policy makers to formulate strategic decisions regarding the best ICT investments and deployment. For example, the study shows that providing accessibility should be a critical focus.

A visual analytical approach to rock art panel condition assessment

NASA Astrophysics Data System (ADS)

Vogt, Brandon J.

Rock art is a term for pecked, scratched, or painted symbols found on rock surfaces, most typically joint faces called rock art panels. Because rock art exists on rock at the atmosphere interface, it is highly susceptible to the destructive processes of weathering. Thus, rock weathering scientists, including those that study both natural and cultural surfaces, play a key role towards understanding rock art longevity. The mapping of weathering forms on rock art panels serves as a basis from which to assess overall panel instability. This work examines fissures, case hardened surfaces, crumbly disintegration, and lichen. Knowledge of instability, as measured through these and other weathering forms, provides integral information to land managers and archaeological conservators required to prioritize panels for remedial action. The work is divided into five chapters, three of which are going to be submitted as a peer-reviewed journal manuscript. The second chapter, written as a manuscript for International Newsletter on Rock Art, describes a specific set of criteria that lead to the development of a mapping tool for weathering forms, called 'mapping weathering forms in three dimensions' (MapWeF). The third chapter, written as a manuscript for Remote Sensing of Environment, presents the methodology used to develop MapWeF. The chapter incorporates terrestrial laser scanning, a geographic information system (GIS), geovisualization, image analysis, and exploratory spatial data analysis (ESDA) to identify, map, and quantify weathering features known to cause instability on rock art panels. The methodology implemented in the third chapter satisfies the criteria described in Chapter Two. In the fourth chapter, prepared as a manuscript for Geomorphology, MapWeF is applied to a site management case study, focusing on a region---southeastern Colorado---with notoriously weak and endangered sandstone rock art panels. The final conclusions chapter describes contributions of the work to GIScience and rock weathering, and discusses how MapWeF, as a diagnostic tool, fits into a larger national vision by linking existing rock art stability characterizations to cultural resource management-related conservation action.

Thermostructural Analysis of Unconventional Wing Structures of a Hyper-X Hypersonic Flight Research Vehicle for the Mach 7 Mission

NASA Technical Reports Server (NTRS)

Ko, William L.; Gong, Leslie

2001-01-01

Heat transfer, thermal stresses, and thermal buckling analyses were performed on the unconventional wing structures of a Hyper-X hypersonic flight research vehicle (designated as X-43) subjected to nominal Mach 7 aerodynamic heating. A wing midspan cross section was selected for the heat transfer and thermal stress analyses. Thermal buckling analysis was performed on three regions of the wing skin (lower or upper); 1) a fore wing panel, 2) an aft wing panel, and 3) a unit panel at the middle of the aft wing panel. A fourth thermal buckling analysis was performed on a midspan wing segment. The unit panel region is identified as the potential thermal buckling initiation zone. Therefore, thermal buckling analysis of the Hyper-X wing panels could be reduced to the thermal buckling analysis of that unit panel. "Buckling temperature magnification factors" were established. Structural temperature-time histories are presented. The results show that the concerns of shear failure at wing and spar welded sites, and of thermal buckling of Hyper-X wing panels, may not arise under Mach 7 conditions.

Design, Optimization and Evaluation of Integrally Stiffened Al 7050 Panel with Curved Stiffeners

NASA Technical Reports Server (NTRS)

Slemp, Wesley C. H.; Bird, R. Keith; Kapania, Rakesh K.; Havens, David; Norris, Ashley; Olliffe, Robert

2011-01-01

A curvilinear stiffened panel was designed, manufactured, and tested in the Combined Load Test Fixture at NASA Langley Research Center. The panel was optimized for minimum mass subjected to constraints on buckling load, yielding, and crippling or local stiffener failure using a new analysis tool named EBF3PanelOpt. The panel was designed for a combined compression-shear loading configuration that is a realistic load case for a typical aircraft wing panel. The panel was loaded beyond buckling and strains and out-of-plane displacements were measured. The experimental data were compared with the strains and out-of-plane deflections from a high fidelity nonlinear finite element analysis and linear elastic finite element analysis of the panel/test-fixture assembly. The numerical results indicated that the panel buckled at the linearly elastic buckling eigenvalue predicted for the panel/test-fixture assembly. The experimental strains prior to buckling compared well with both the linear and nonlinear finite element model.

Boundary element analyses for sound transmission loss of panels.

PubMed

Zhou, Ran; Crocker, Malcolm J

2010-02-01

The sound transmission characteristics of an aluminum panel and two composite sandwich panels were investigated by using two boundary element analyses. The effect of air loading on the structural behavior of the panels is included in one boundary element analysis, by using a light-fluid approximation for the eigenmode series to evaluate the structural response. In the other boundary element analysis, the air loading is treated as an added mass. The effect of the modal energy loss factor on the sound transmission loss of the panels was investigated. Both boundary element analyses were used to study the sound transmission loss of symmetric sandwich panels excited by a random incidence acoustic field. A classical wave impedance analysis was also used to make sound transmission loss predictions for the two foam-filled honeycomb sandwich panels. Comparisons between predictions of sound transmission loss for the two foam-filled honeycomb sandwich panels excited by a random incidence acoustic field obtained from the wave impedance analysis, the two boundary element analyses, and experimental measurements are presented.

Balancing Work and Family: A Panel Analysis of the Impact of Part-Time Work on the Experience of Time Pressure

ERIC Educational Resources Information Center

Laurijssen, Ilse; Glorieux, Ignace

2013-01-01

In this article we consider the consequences of work-family reconciliation, in terms of the extent to which the adjustment of the labour market career to family demands (by women) contributes to a better work-life balance. Using the Flemish SONAR-data, we analyse how changes in work and family conditions between the age of 26 and 29 are related to…

Buckling Design and Analysis of a Payload Fairing One-Sixth Cylindrical Arc-Segment Panel

NASA Technical Reports Server (NTRS)

Kosareo, Daniel N.; Oliver, Stanley T.; Bednarcyk, Brett A.

2013-01-01

Design and analysis results are reported for a panel that is a 16th arc-segment of a full 33-ft diameter cylindrical barrel section of a payload fairing structure. Six such panels could be used to construct the fairing barrel, and, as such, compression buckling testing of a 16th arc-segment panel would serve as a validation test of the buckling analyses used to design the fairing panels. In this report, linear and nonlinear buckling analyses have been performed using finite element software for 16th arc-segment panels composed of aluminum honeycomb core with graphiteepoxy composite facesheets and an alternative fiber reinforced foam (FRF) composite sandwich design. The cross sections of both concepts were sized to represent realistic Space Launch Systems (SLS) Payload Fairing panels. Based on shell-based linear buckling analyses, smaller, more manageable buckling test panel dimensions were determined such that the panel would still be expected to buckle with a circumferential (as opposed to column-like) mode with significant separation between the first and second buckling modes. More detailed nonlinear buckling analyses were then conducted for honeycomb panels of various sizes using both Abaqus and ANSYS finite element codes, and for the smaller size panel, a solid-based finite element analysis was conducted. Finally, for the smaller size FRF panel, nonlinear buckling analysis was performed wherein geometric imperfections measured from an actual manufactured FRF were included. It was found that the measured imperfection did not significantly affect the panel's predicted buckling response

A mobility based vibroacoustic energy transmission simulation into an enclosure through a double-wall panel.

PubMed

Sahu, Atanu; Bhattacharya, Partha; Niyogi, Arup Guha; Rose, Michael

2017-06-01

Double-wall panels are known for their superior sound insulation properties over single wall panels as a sound barrier. The sound transmission phenomenon through a double-wall structure is a complex process involving vibroacoustic interaction between structural panels, the air-cushion in between, and the secondary acoustic domain. It is in this context a versatile and a fully coupled technique based on the finite-element-boundary element model is developed that enables estimation of sound transfer through a double-wall panel into an adjacent enclosure while satisfying the displacement compatibility across the interface. The contribution of individual components in the transmitted energy is identified through numerical simulations.

Manual and automatic flight control during severe turbulence penetration

NASA Technical Reports Server (NTRS)

Johnston, D. E.; Klein, R. H.; Hoh, R. H.

1976-01-01

An analytical and experimental investigation of possible contributing factors in jet aircraft turbulence upsets was conducted. Major contributing factors identified included autopilot and display deficiencies, the large aircraft inertia and associated long response time, and excessive pilot workload. An integrated flight and thrust energy management director system was synthesized. The system was incorporated in a moving-base simulation and evaluated using highly experienced airline pilots. The evaluation included comparison of pilot workload and flight performance during severe turbulence penetration utilizing four control/display concepts: manual control with conventional full panel display, conventional autopilot (A/P-A) with conventional full panel display, improved autopilot (A/P-B) with conventional full panel display plus thrust director display, and longitudinal flight director with conventional full panel display plus thrust director display. Simulation results show improved performance, reduced pilot workload, and a pilot preference for the autopilot system controlling to the flight director command and manual control of thrust following the trim thrust director.

Stress analysis and buckling of J-stiffened graphite-epoxy panel

NASA Technical Reports Server (NTRS)

Davis, R. C.

1980-01-01

A graphite epoxy shear panel with bonded on J stiffeners was investigated. The panel, loaded to buckling in a picture frame shear test is described. Two finite element models, each of which included the doubler material bonded to the panel skin under the stiffeners and at the panel edges, were used to make a stress analysis of the panel. The shear load distributions in the panel from two commonly used boundary conditions, applied shear load and applied displacement, were compared with the results from one of the finite element models that included the picture frame test fixture.

Gender-specific Regulatory Challenges to Product Approval: a panel discussion.

PubMed

McGregor, Alyson J; Barr, Helen; Greenberg, Marna R; Safdar, Basmah; Wildgoose, Peter; Wright, David W; Hollander, Judd E

2014-12-01

On May 13, 2014, a 1-hour panel discussion session titled "Gender-specific Regulatory Challenges to Product Approval" was held during the Academic Emergency Medicine consensus conference, "Gender-specific Research in Emergency Medicine: Investigate, Understand, and Translate How Gender Affects Patient Outcomes." The session sought to bring together leaders in emergency medicine (EM) research, authors, and reviewers in EM research publications, as well as faculty, fellows, residents, and students engaged in research and clinical practice. A panel was convened involving a representative from the Office of Women's Health of the U.S. Food and Drug Administration, two pharmaceutical executives, and a clinical EM researcher. The moderated discussion also involved audience members who contributed significantly to the dialogue. Historical background leading up to the session along with the main themes of the discussion are reproduced in this article. These revolve around sex- and gender-specific research, statistical analysis of sex and gender, clinical practice, financial costs associated with pharmaceutical development, adaptive design, and specific recommendations on the regulatory process as it affects the specialty of EM. © 2014 by the Society for Academic Emergency Medicine.

Gender-specific Regulatory Challenges to Product Approval: A Panel Discussion

PubMed Central

McGregor, Alyson J.; Barr, Helen; Greenberg, Marna Rayl; Safdar, Basmah; Wildgoose, Peter; Wright, David W.; Hollander, Judd E.

2015-01-01

On May 13, 2014, a 1-hour panel discussion session titled “Gender-Specific Regulatory Challenges to Product Approval” was held during the Academic Emergency Medicine consensus conference, “Gender-Specific Research in Emergency Medicine: Investigate, Understand, and Translate How Gender Affects Patient Outcomes.” The session sought to bring together leaders in emergency medicine (EM) research, authors, and reviewers in EM research publications, as well as faculty, fellows, residents, and students engaged in research and clinical practice. A panel was convened involving a representative from the Office of Women’s Health of the U.S. Food and Drug Administration, two pharmaceutical executives, and a clinical EM researcher. The moderated discussion also involved audience members who contributed significantly to the dialogue. Historical background leading up to the session along with the main themes of the discussion are reproduced in this article. These revolve around sex- and gender-specific research, statistical analysis of sex and gender, clinical practice, financial costs associated with pharmaceutical development, adaptive design, and specific recommendations on the regulatory process as it affects the specialty of EM. PMID:25443664

PRIORITIES FOR HEALTH ECONOMIC METHODOLOGICAL RESEARCH: RESULTS OF AN EXPERT CONSULTATION.

PubMed

Tordrup, David; Chouaid, Christos; Cuijpers, Pim; Dab, William; van Dongen, Johanna Maria; Espin, Jaime; Jönsson, Bengt; Léonard, Christian; McDaid, David; McKee, Martin; Miguel, José Pereira; Patel, Anita; Reginster, Jean-Yves; Ricciardi, Walter; Rutten-van Molken, Maureen; Rupel, Valentina Prevolnik; Sach, Tracey; Sassi, Franco; Waugh, Norman; Bertollini, Roberto

2017-01-01

The importance of economic evaluation in decision making is growing with increasing budgetary pressures on health systems. Diverse economic evidence is available for a range of interventions across national contexts within Europe, but little attention has been given to identifying evidence gaps that, if filled, could contribute to more efficient allocation of resources. One objective of the Research Agenda for Health Economic Evaluation project is to determine the most important methodological evidence gaps for the ten highest burden conditions in the European Union (EU), and to suggest ways of filling these gaps. The highest burden conditions in the EU by Disability Adjusted Life Years were determined using the Global Burden of Disease study. Clinical interventions were identified for each condition based on published guidelines, and economic evaluations indexed in MEDLINE were mapped to each intervention. A panel of public health and health economics experts discussed the evidence during a workshop and identified evidence gaps. The literature analysis contributed to identifying cross-cutting methodological and technical issues, which were considered by the expert panel to derive methodological research priorities. The panel suggests a research agenda for health economics which incorporates the use of real-world evidence in the assessment of new and existing interventions; increased understanding of cost-effectiveness according to patient characteristics beyond the "-omics" approach to inform both investment and disinvestment decisions; methods for assessment of complex interventions; improved cross-talk between economic evaluations from health and other sectors; early health technology assessment; and standardized, transferable approaches to economic modeling.

Aircraft interior noise reduction by alternate resonance tuning

NASA Technical Reports Server (NTRS)

Gottwald, James A.; Bliss, Donald B.

1990-01-01

The focus is on a noise control method which considers aircraft fuselages lined with panels alternately tuned to frequencies above and below the frequency that must be attenuated. An interior noise reduction called alternate resonance tuning (ART) is described both theoretically and experimentally. Problems dealing with tuning single paneled wall structures for optimum noise reduction using the ART methodology are presented, and three theoretical problems are analyzed. The first analysis is a three dimensional, full acoustic solution for tuning a panel wall composed of repeating sections with four different panel tunings within that section, where the panels are modeled as idealized spring-mass-damper systems. The second analysis is a two dimensional, full acoustic solution for a panel geometry influenced by the effect of a propagating external pressure field such as that which might be associated with propeller passage by a fuselage. To reduce the analysis complexity, idealized spring-mass-damper panels are again employed. The final theoretical analysis presents the general four panel problem with real panel sections, where the effect of higher structural modes is discussed. Results from an experimental program highlight real applications of the ART concept and show the effectiveness of the tuning on real structures.

Valorization of Tunisian alfa fibres and sumac tannins for the elaboration of biodegradable insulating panels

NASA Astrophysics Data System (ADS)

Saad, Houda; Charrier, Bertrand; Ayed, Naceur; Charrier-El-Bouhtoury, Fatima

2017-10-01

Alfa leaves are important renewable raw materials in Tunisia where they are used basically in handcrafts and paper industry. Sumac is also an abundant species in Tunisia known for its high tannin content and is basically used in traditional medicine. To valorize these natural resources, we studied, for the first time, the possibility of making insulating panels based on alfa fibres and sumac tannins based adhesive. Firstly, alfa leaves were treated with an alkali solution as it is one of the standard procedures commonly used in the paper industry to extract cellulosic fibres. Mercerization effects were studied by characterizing fibres thermal properties and fibres surface morphology. Secondly, the sumac tannin based resin was formulated and characterized. Finally, the insulating panel was elaborated and characterized by determining its thermal conductivity. The thermal gravimetric analysis results show improvement in the thermal stability of fibres after alkali treatment. Environmental Scanning Electron Microscopy showed changes on treated alfa surface which could promote the fibre-matrix adhesion. The reactivity of sumac tannins to formaldehyde test (Stiasny number) showed the possible use of sumac tannins in wood adhesive formulation. Thermomechanical analysis and strength analysis of sumac tannin/hexamin based resin highlighted acceptable bonding properties. The thermal conductivity measurement showed an average value equal to 0.110 W/m K. Contribution to the topical issue "Materials for Energy harvesting, conversion and storage II (ICOME 2016)", edited by Jean-Michel Nunzi, Rachid Bennacer and Mohammed El Ganaoui

Novel Composites for Wing and Fuselage Applications: Speedy Nonlinear Analysis of Postbuckled Panels in Shear (SNAPPS)

NASA Technical Reports Server (NTRS)

Sharp, Dave; Sobel, Larry

1997-01-01

A simple and rapid analysis method, consisting of a number of modular, 'strength-of-materials-type' models, is presented for predicting the nonlinear response and stiffener separation of postbuckled, flat, composite, shear panels. The analysis determines the maximum principal tensile stress in the skin surface layer under to toe. Failure is said to occur when this stress reaches the mean transverse tensile strength of the layer. The analysis methodology consists of a number of closed-form equations that can easily be used in a 'hand analysis. For expediency, they have been programmed into a preliminary design code called SNAPPS (Speedy Nonlinear Analysis of Postbuckled Panels in Shear), which rapidly predicts postbuckling response of the panel for each value of the applied shear load. SNAPPS response and failure predictions were found to agree well with test results for three panels with widely different geometries, laminates and stiffnesses. Design guidelines are given for increasing the load-carrying capacity of stiffened, composite shear panels.

Panel-flutter analysis of a thermal protection-shield concept for the space shuttle.

NASA Technical Reports Server (NTRS)

Cunningham, H. J.

1972-01-01

Analysis of the panel flutter characteristics of a candidate thermal protection system (TPS) for the space shuttle, using piston theory aerodynamics and Lagrange equations. The results show the TPS candidate panel array to be deep in the 'no-flutter' region during launch and, therefore, safe from panel flutter.

77 FR 21788 - Center for Scientific Review Notice of Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-11

... Development, Stem Cell and Myocardial Regeneration. Date: May 10, 2012. Time: 2 p.m. to 3:30 p.m. Agenda: To... for Scientific Review Special Emphasis Panel; RFA Panel: Single Cell Analysis Reviews. Date: May 8... for Scientific Review Special Emphasis Panel; RFA Panel: Single Cell Analysis Reviews. Date: May 9...

Test and analysis of a stitched RFI graphite-epoxy panel with a fuel access door

NASA Technical Reports Server (NTRS)

Jegley, Dawn C.; Waters, W. Allen, Jr.

1994-01-01

A stitched RFI graphite-epoxy panel with a fuel access door was analyzed using a finite element analysis and loaded to failure in compression. The panel was initially 56-inches long and 36.75-inches wide and the oval access door was 18-inches long and 15-inches wide. The panel was impact damaged with impact energy of 100 ft-lb prior to compressive loading; however, no impact damage was detectable visually or by A-scan. The panel carried a failure load of 695,000 Ib and global failure strain of .00494 in/in. Analysis indicated the panel would fail due to collapse at a load of 688,100 Ib. The test data indicate that the maximum strain in a region near the access door was .0096 in/in and analysis indicates a local surface strain of .010 in/in at the panel's failure load. The panel did not fail through the impact damage, but instead failed through bolt holes for attachment of the access door in a region of high strain.

Slow-wave metamaterial open panels for efficient reduction of low-frequency sound transmission

NASA Astrophysics Data System (ADS)

Yang, Jieun; Lee, Joong Seok; Lee, Hyeong Rae; Kang, Yeon June; Kim, Yoon Young

2018-02-01

Sound transmission reduction is typically governed by the mass law, requiring thicker panels to handle lower frequencies. When open holes must be inserted in panels for heat transfer, ventilation, or other purposes, the efficient reduction of sound transmission through holey panels becomes difficult, especially in the low-frequency ranges. Here, we propose slow-wave metamaterial open panels that can dramatically lower the working frequencies of sound transmission loss. Global resonances originating from slow waves realized by multiply inserted, elaborately designed subwavelength rigid partitions between two thin holey plates contribute to sound transmission reductions at lower frequencies. Owing to the dispersive characteristics of the present metamaterial panels, local resonances that trap sound in the partitions also occur at higher frequencies, exhibiting negative effective bulk moduli and zero effective velocities. As a result, low-frequency broadened sound transmission reduction is realized efficiently in the present metamaterial panels. The theoretical model of the proposed metamaterial open panels is derived using an effective medium approach and verified by numerical and experimental investigations.

Integrated Modeling and Analysis of Physical Oceanographic and Acoustic Processes

DTIC Science & Technology

2014-09-30

dependence of the energy conversion on the ratio of the IW beam slope to the topographic slope, SIW /Stopo. The top panel of Fig. 8 illustrates that...in the abyssal oceans, where typically SIW /Stopo > 1 for tall seamounts and ridges, the entire bottom topography contributes to the generation of...internal waves. In contrast, for (a) (b) 18 moderate ocean depths (say less than 4 km), where typically SIW /Stopo < 1 for seamounts and ridges, the

Evaluating the financial efficiency of energy and water saving installations in passive house

NASA Astrophysics Data System (ADS)

Stec, Agnieszka; Mazur, Aleksandra; Słyś, Daniel

2017-11-01

The article contains the outcomes of the Life Cycle Cost analysis for alternative energy and water sources utilized in passive buildings. The solutions taken into account included: heat pumps, solar collectors, photovoltaic panels, Drain Water Heat Recovery units, Rain Water Harvesting Systems and Greywater Recycling Systems. In addition, air pollution emission reduction was also calculated for all the installation variants analyzed. The analysis have shown that the systems under consideration could serve as alternatives for traditional installations. Their use has resulted in reductions in the consumption of fossil fuels and natural water resources, thus contributing to environmental improvements.

A Review of Air Pollutant Damage to Materials

EPA Science Inventory

Report prepared as U.S. contribution to Panel 3 of NATO Committee on Challenges of Modern Society Pilot Study on Air Pollution Control Strategies and Impact Modeling. Panel 3 focuses on air pollutant impact and will publish 4 reports on air pollutants effects; this is the first i...

Tackling reliability and construct validity: the systematic development of a qualitative protocol for skill and incident analysis.

PubMed

Savage, Trevor Nicholas; McIntosh, Andrew Stuart

2017-03-01

It is important to understand factors contributing to and directly causing sports injuries to improve the effectiveness and safety of sports skills. The characteristics of injury events must be evaluated and described meaningfully and reliably. However, many complex skills cannot be effectively investigated quantitatively because of ethical, technological and validity considerations. Increasingly, qualitative methods are being used to investigate human movement for research purposes, but there are concerns about reliability and measurement bias of such methods. Using the tackle in Rugby union as an example, we outline a systematic approach for developing a skill analysis protocol with a focus on improving objectivity, validity and reliability. Characteristics for analysis were selected using qualitative analysis and biomechanical theoretical models and epidemiological and coaching literature. An expert panel comprising subject matter experts provided feedback and the inter-rater reliability of the protocol was assessed using ten trained raters. The inter-rater reliability results were reviewed by the expert panel and the protocol was revised and assessed in a second inter-rater reliability study. Mean agreement in the second study improved and was comparable (52-90% agreement and ICC between 0.6 and 0.9) with other studies that have reported inter-rater reliability of qualitative analysis of human movement.

SCBUCKLE user's manual: Buckling analysis program for simple supported and clamped panels

NASA Technical Reports Server (NTRS)

Cruz, Juan R.

1993-01-01

The program SCBUCKLE calculates the buckling loads and mode shapes of cylindrically curved, rectangular panels. The panel is assumed to have no imperfections. SCBUCKLE is capable of analyzing specially orthotropic symmetric panels (i.e., A(sub 16) = A(sub 26) = 0.0, D(sub 16) = D(sub 26) = 0.0, B(sub ij) = 0.0). The analysis includes first-order transverse shear theory and is capable of modeling sandwich panels. The analysis supports two types of boundary conditions: either simply supported or clamped on all four edges. The panel can be subjected to linearly varying normal loads N(sub x) and N(sub y) in addition to a constant shear load N(sub xy). The applied loads can be divided into two parts: a preload component; and a variable (eigenvalue-dependent) component. The analysis is based on the modified Donnell's equations for shallow shells. The governing equations are solved by Galerkin's method.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, K.

In the summer of 2013 the International Committee on Future Accelerators (ICFA) established a Neutrino Panel with the mandate: <<>>In its first year the Panel organised a series of regional Town Meetings to collect input from the community and to receive reports from the regional planning exercises. The Panel distilled its findings and presented them in a report to ICFA [1]. In this contribution the formation and composition of the Panel are presented together with a summary of the Panel’s findings from the three Regional Town Meetings. The Panel’s initial conclusions are then articulated and the steps that the Panelmore » seeks to take are outlined.« less

Damage tolerance modeling and validation of a wireless sensory composite panel for a structural health monitoring system

NASA Astrophysics Data System (ADS)

Talagani, Mohamad R.; Abdi, Frank; Saravanos, Dimitris; Chrysohoidis, Nikos; Nikbin, Kamran; Ragalini, Rose; Rodov, Irena

2013-05-01

The paper proposes the diagnostic and prognostic modeling and test validation of a Wireless Integrated Strain Monitoring and Simulation System (WISMOS). The effort verifies a hardware and web based software tool that is able to evaluate and optimize sensorized aerospace composite structures for the purpose of Structural Health Monitoring (SHM). The tool is an extension of an existing suite of an SHM system, based on a diagnostic-prognostic system (DPS) methodology. The goal of the extended SHM-DPS is to apply multi-scale nonlinear physics-based Progressive Failure analyses to the "as-is" structural configuration to determine residual strength, remaining service life, and future inspection intervals and maintenance procedures. The DPS solution meets the JTI Green Regional Aircraft (GRA) goals towards low weight, durable and reliable commercial aircraft. It will take advantage of the currently developed methodologies within the European Clean sky JTI project WISMOS, with the capability to transmit, store and process strain data from a network of wireless sensors (e.g. strain gages, FBGA) and utilize a DPS-based methodology, based on multi scale progressive failure analysis (MS-PFA), to determine structural health and to advice with respect to condition based inspection and maintenance. As part of the validation of the Diagnostic and prognostic system, Carbon/Epoxy ASTM coupons were fabricated and tested to extract the mechanical properties. Subsequently two composite stiffened panels were manufactured, instrumented and tested under compressive loading: 1) an undamaged stiffened buckling panel; and 2) a damaged stiffened buckling panel including an initial diamond cut. Next numerical Finite element models of the two panels were developed and analyzed under test conditions using Multi-Scale Progressive Failure Analysis (an extension of FEM) to evaluate the damage/fracture evolution process, as well as the identification of contributing failure modes. The comparisons between predictions and test results were within 10% accuracy.

Shear and compression buckling analysis for anisotropic panels with centrally located elliptical cutouts

NASA Technical Reports Server (NTRS)

Britt, V. O.

1993-01-01

An approximate analysis for buckling of biaxial- and shear-loaded anisotropic panels with centrally located elliptical cutouts is presented in the present paper. The analysis is composed of two parts, a prebuckling analysis and a buckling analysis. The prebuckling solution is determined using Lekhnitskii's complex variable equations of plane elastostatics combined with a Laurent series approximation and a boundary collocation method. The buckling solution is obtained using the principle of minimum potential energy. A by-product of the minimum potential energy equation is an integral equation which is solved using Gaussian quadrature. Comparisons with documented experimental results and finite element analyses indicate that the approximate analysis accurately predicts the buckling loads of square biaxial- and shear-loaded panels having elliptical cutouts with major axes up to sixty percent of the panel width. Results of a parametric study are presented for shear- and compression-loaded rectangular anisotropic panels with elliptical cutouts. The effects of panel aspect ratio, cutout shape, cutout size, cutout orientation, laminate anisotropy, and combined loading on the buckling load are examined.

Atomic Oxygen Erosion of EVA-Stranded Soft-Goods on the ISS

NASA Technical Reports Server (NTRS)

Alred, John W.

2017-01-01

This paper presents the results of an analysis to calculate the cumulative, effective atomic oxygen (AO) flux impinging on short-duration EVA tethers used to secure panel NOD1/C2-02 and panel LAB/C2-03. Shadowing from the ram reduces the AO flux on much of the Node 1 panel. On the Lab panel, the tethers are essentially in the ram flux. Table 1 summarizes the results of the analysis for Node 1 and the US Lab panels.

Informational Ambiguity and Survey Bias: Husbands' and Wives' Reports on Their Contribution to Their Families

ERIC Educational Resources Information Center

Tao, Hung-Lin

2013-01-01

The present study uses panel data models to control unobserved characteristics and to investigate how the presence of spouses in interviews influences reports regarding housework and earnings contributions. Both husbands and wives relatively overreport their housework contributions but do not overreport their earnings contributions. The amount of…

Gene panel testing for inherited cancer risk.

PubMed

Hall, Michael J; Forman, Andrea D; Pilarski, Robert; Wiesner, Georgia; Giri, Veda N

2014-09-01

Next-generation sequencing technologies have ushered in the capability to assess multiple genes in parallel for genetic alterations that may contribute to inherited risk for cancers in families. Thus, gene panel testing is now an option in the setting of genetic counseling and testing for cancer risk. This article describes the many gene panel testing options clinically available to assess inherited cancer susceptibility, the potential advantages and challenges associated with various types of panels, clinical scenarios in which gene panels may be particularly useful in cancer risk assessment, and testing and counseling considerations. Given the potential issues for patients and their families, gene panel testing for inherited cancer risk is recommended to be offered in conjunction or consultation with an experienced cancer genetic specialist, such as a certified genetic counselor or geneticist, as an integral part of the testing process. Copyright © 2014 by the National Comprehensive Cancer Network.

Expeditionary Mobile Operations Center (EMOC)

DTIC Science & Technology

2014-09-01

use of solar panels and wind turbines (Barreto 2011) to contribute to operating power. Testing and evaluation of the EOC-2’s power requirements reveals...environments to reduce the consumption of fossil fuels. Once these technologies (for example, solar panels and wind turbines ) are identified and...64 b. Encryption and Wireless Access Point ..................... 64 c. Server System

49 CFR 571.221 - Standard No. 221; School bus body joint strength.

Code of Federal Regulations, 2011 CFR

2011-10-01

... and any structure forward of the passenger compartment. Maintenance access panel means a body panel... so that it does not bisect a spot weld or a discrete fastener. Support members which contribute to... structure attached to joint members, shall remain attached to the test specimen, except that material may be...

49 CFR 571.221 - Standard No. 221; School bus body joint strength.

Code of Federal Regulations, 2010 CFR

2010-10-01

... and any structure forward of the passenger compartment. Maintenance access panel means a body panel... so that it does not bisect a spot weld or a discrete fastener. Support members which contribute to... structure attached to joint members, shall remain attached to the test specimen, except that material may be...

49 CFR 571.221 - Standard No. 221; School bus body joint strength.

Code of Federal Regulations, 2013 CFR

2013-10-01

... and any structure forward of the passenger compartment. Maintenance access panel means a body panel... so that it does not bisect a spot weld or a discrete fastener. Support members which contribute to... structure attached to joint members, shall remain attached to the test specimen, except that material may be...

49 CFR 571.221 - Standard No. 221; School bus body joint strength.

Code of Federal Regulations, 2012 CFR

2012-10-01

... and any structure forward of the passenger compartment. Maintenance access panel means a body panel... so that it does not bisect a spot weld or a discrete fastener. Support members which contribute to... structure attached to joint members, shall remain attached to the test specimen, except that material may be...

49 CFR 571.221 - Standard No. 221; School bus body joint strength.

Code of Federal Regulations, 2014 CFR

2014-10-01

... and any structure forward of the passenger compartment. Maintenance access panel means a body panel... so that it does not bisect a spot weld or a discrete fastener. Support members which contribute to... structure attached to joint members, shall remain attached to the test specimen, except that material may be...

Radiation hazards to man

NASA Technical Reports Server (NTRS)

Curtis, S. B.; Wilkinson, M. C.

1971-01-01

The secondary dose contribution expected from the heavy primaries of the galactic cosmic rays was evaluated by a calculational technique developed in this study. Improvements in the solar and galactic cosmic ray environments made possible by recent experimental and theoretical work are discussed and presented. The recommendations of the National Academy of Sciences' space radiation study panel, are used in conjunction with a shielding analysis, to evaluate the radiation status of an astronaut during the triple solar particle event of 10, 14, 16 July 1959.

Compressive and shear buckling analysis of metal matrix composite sandwich panels under different thermal environments

NASA Technical Reports Server (NTRS)

Ko, William L.; Jackson, Raymond H.

1993-01-01

Combined inplane compressive and shear buckling analysis was conducted on flat rectangular sandwich panels using the Raleigh-Ritz minimum energy method with a consideration of transverse shear effect of the sandwich core. The sandwich panels were fabricated with titanium honeycomb core and laminated metal matrix composite face sheets. The results show that slightly slender (along unidirectional compressive loading axis) rectangular sandwich panels have the most desirable stiffness-to-weight ratios for aerospace structural applications; the degradation of buckling strength of sandwich panels with rising temperature is faster in shear than in compression; and the fiber orientation of the face sheets for optimum combined-load buckling strength of sandwich panels is a strong function of both loading condition and panel aspect ratio. Under the same specific weight and panel aspect ratio, a sandwich panel with metal matrix composite face sheets has much higher buckling strength than one having monolithic face sheets.

Robust analysis of the determinants of healthcare expenditure growth: evidence from panel data for low-, middle- and high-income countries.

PubMed

Younsi, Moheddine; Chakroun, Mohamed; Nafla, Amine

2016-10-01

This paper examines the determinants of healthcare expenditure for low-, middle- and high-income countries, and it quantifies their influences in order to assess policies for achieving universal health coverage. We elaborate two models, a fixed-effect model and the dynamic panel model, to estimate the factors associated with the total health expenditure growth as well as its major components for 167 countries over the period of 1993-2013. The panel data on total health expenditure per capita and its components were taken from the World Development Indicators. Overall, our results showed that total health expenditure per capita is rising in all countries over time as a result of rising incomes. However, our estimates showed that the income elasticity of health expenditure ranged from 0.75 to 0.96 in the fixed-effect static panel model, while in the dynamic panel model, it was smaller and ranged from 0.16 to 0.47. Our empirical findings indicate that development assistance for health reduced government domestic spending on health but increased total government health spending. Our results also indicate that the trend in health expenditure growth is significantly depending with the country's economic development. In addition, out-of-pocket expenditure is powerfully influenced by a country's capacity to increase general government revenues and social insurance contributions. Knowledge of factors associated to health expenditure might help policy makers to make wise judgments, plan health reforms and allocate resources efficiently. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

A Receptor-Based Explanation for Tsetse Fly Catch Distribution between Coloured Cloth Panels and Flanking Nets

PubMed Central

Santer, Roger D.

2015-01-01

Tsetse flies transmit trypanosomes that cause nagana in cattle, and sleeping sickness in humans. Therefore, optimising visual baits to control tsetse is an important priority. Tsetse are intercepted at visual baits due to their initial attraction to the bait, and their subsequent contact with it due to landing or accidental collision. Attraction is proposed to be driven in part by a chromatic mechanism to which a UV-blue photoreceptor contributes positively, and a UV and a green photoreceptor contribute negatively. Landing responses are elicited by stimuli with low luminance, but many studies also find apparently strong landing responses when stimuli have high UV reflectivity, which would imply that UV wavelengths contribute negatively to attraction at a distance, but positively to landing responses at close range. The strength of landing responses is often judged using the number of tsetse sampled at a cloth panel expressed as a proportion of the combined catch of the cloth panel and a flanking net that samples circling flies. I modelled these data from two previously published field studies, using calculated fly photoreceptor excitations as predictors. I found that the proportion of tsetse caught on the cloth panel increased with an index representing the chromatic mechanism driving attraction, as would be expected if the same mechanism underlay both long- and close-range attraction. However, the proportion of tsetse caught on the cloth panel also increased with excitation of the UV-sensitive R7p photoreceptor, in an apparently separate but interacting behavioural mechanism. This R7p-driven effect resembles the fly open-space response which is believed to underlie their dispersal towards areas of open sky. As such, the proportion of tsetse that contact a cloth panel likely reflects a combination of deliberate landings by potentially host-seeking tsetse, and accidental collisions by those seeking to disperse, with a separate visual mechanism underlying each behaviour. PMID:26474406

Genetic Structure, Linkage Disequilibrium and Association Mapping of Verticillium Wilt Resistance in Elite Cotton (Gossypium hirsutum L.) Germplasm Population

PubMed Central

Zhao, Yunlei; Wang, Hongmei; Chen, Wei; Li, Yunhai

2014-01-01

Understanding the population structure and linkage disequilibrium in an association panel can effectively avoid spurious associations and improve the accuracy in association mapping. In this study, one hundred and fifty eight elite cotton (Gossypium hirsutum L.) germplasm from all over the world, which were genotyped with 212 whole genome-wide marker loci and phenotyped with an disease nursery and greenhouse screening method, were assayed for population structure, linkage disequilibrium, and association mapping of Verticillium wilt resistance. A total of 480 alleles ranging from 2 to 4 per locus were identified from all collections. Model-based analysis identified two groups (G1 and G2) and seven subgroups (G1a–c, G2a–d), and differentiation analysis showed that subgroup having a single origin or pedigree was apt to differentiate with those having a mixed origin. Only 8.12% linked marker pairs showed significant LD (P<0.001) in this association panel. The LD level for linked markers is significantly higher than that for unlinked markers, suggesting that physical linkage strongly influences LD in this panel, and LD level was elevated when the panel was classified into groups and subgroups. The LD decay analysis for several chromosomes showed that different chromosomes showed a notable change in LD decay distances for the same gene pool. Based on the disease nursery and greenhouse environment, 42 marker loci associated with Verticillium wilt resistance were identified through association mapping, which widely were distributed among 15 chromosomes. Among which 10 marker loci were found to be consistent with previously identified QTLs and 32 were new unreported marker loci, and QTL clusters for Verticillium wilt resistanc on Chr.16 were also proved in our study, which was consistent with the strong linkage in this chromosome. Our results would contribute to association mapping and supply the marker candidates for marker-assisted selection of Verticillium wilt resistance in cotton. PMID:24466016

A Panel Analysis of the Strategic Association Between Information and Communication Technology and Public Health Delivery

PubMed Central

Wu, Sarah Jinhui

2012-01-01

Background In this exploratory research, we use panel data analysis to examine the correlation between Information and Communication Technology (ICTs) and public health delivery at the country level. Objective The goal of this exploratory research is to examine the strategic association over time between ICTs and country-level public health. Methods Using data from the World Development Indicators, we construct a panel data set of countries of five different income levels and look closely at the period from 2000 to 2008. The panel data analysis allows us to explore this dynamic relationship under the control for unobserved country-specific effects by using a fixed-effects estimation method. In particular,, we examine the association of five ICT factors with five public health indicators: adolescent fertility rate, child immunization coverage, tuberculosis case detected, life expectancy, and adult mortality rate. Results First, overall ICTs’ factors substantially improve a country’s public health delivery on the top of wealth effect. Second, among all the ICTs’ factors, accessibility is the only one that is associated with improvements in all aspects of public health delivery, while the contributions from the usage, quality, and applications are negligible. ICTs’ accessibility factor is associated with a considerable extension to life expectancy and reduced adult mortality rate. Third, all entity-specific factors are significant in each model, indicating that countries’ economic development level does influence their public health delivery. Conclusions Our results indicate that ICT accessibility has a strong association with effective delivery of public health. There are others, but the key strategic applications are eHealth and mHealth. The findings of this study will help government officials and public health policy makers to formulate strategic decisions regarding the best ICT investments and deployment. For example, the study shows that providing accessibility should be a critical focus. PMID:23089193

Use of cultural consensus analysis to evaluate expert feedback of median safety.

PubMed

Kim, Tae-Gyu; Donnell, Eric T; Lee, Dongmin

2008-07-01

Cultural consensus analysis is a statistical method that can be used to assess participant responses to survey questions. The technique concurrently estimates the knowledge of each survey participant and estimates the culturally correct answer to each question asked, based on the existence of consensus among survey participants. The main objectives of this paper are to present the cultural consensus methodology and apply it to a set of median design and safety survey data that were collected using the Delphi method. A total of 21 Delphi survey participants were asked to answer research questions related to cross-median crashes. It was found that the Delphi panel had agreeable opinions with respect to the association of average daily traffic (ADT) and heavy vehicle percentage combination on the risk of cross-median crashes; relative importance of additional factors, other than ADT, median width, and crash history that may contribute to cross-median crashes; and, the relative importance of geometric factors that may be associated with the likelihood of cross-median crashes. Therefore, the findings from the cultural consensus analysis indicate that the expert panel selected to participate in the Delphi survey shared a common knowledge pool relative to the association between median design and safety. There were, however, diverse opinions regarding median barrier type and its preferred placement location. The panel showed a higher level of knowledge on the relative importance regarding the association of geometric factors on cross-median crashes likelihood than on other issues considered. The results of the cultural consensus analysis of the present median design and safety survey data could be used to design a focused field study of median safety.

Advanced composites structural concepts and materials technologies for primary aircraft structures. Structural response and failure analysis: ISPAN modules users manual

NASA Technical Reports Server (NTRS)

Hairr, John W.; Huang, Jui-Ten; Ingram, J. Edward; Shah, Bharat M.

1992-01-01

The ISPAN Program (Interactive Stiffened Panel Analysis) is an interactive design tool that is intended to provide a means of performing simple and self contained preliminary analysis of aircraft primary structures made of composite materials. The program combines a series of modules with the finite element code DIAL as its backbone. Four ISPAN Modules were developed and are documented. These include: (1) flat stiffened panel; (2) curved stiffened panel; (3) flat tubular panel; and (4) curved geodesic panel. Users are instructed to input geometric and material properties, load information and types of analysis (linear, bifurcation buckling, or post-buckling) interactively. The program utilizing this information will generate finite element mesh and perform analysis. The output in the form of summary tables of stress or margins of safety, contour plots of loads or stress, and deflected shape plots may be generalized and used to evaluate specific design.

Relation between sensory analysis and rheology of body lotions.

PubMed

Moravkova, T; Filip, P

2016-12-01

Evaluation of sensory attributes of cosmetic products is traditionally based on sensory panels. However, in some cases, a suitable candidate method that can reduce time and costs is the use of instrumental analysis that can detect relatively very small changes of entry ingredients. Such approach has been already applied for emollients, salt content, stabilizers, etc. The aim of this contribution is to apply the relations between sensory analysis and rheology to a series of body lotions differing in the contents of emulsifiers and viscosity regulators. Sensory and rheological analyses are related. Rheological analysis can represent a good alternative to basic orientation in chosen customer's feelings. A rotational rheometer is the only instrumental device required for the measurements. An empirical rheological model was proposed by means of which the selected sensory attributes were evaluated using the numerical values of adjustable model parameters. This approach exhibited a very good agreement with the results obtained by the sensory panel. It was shown that a description of chosen sensory attributes can be responsibly carried out by rheological measurements, that is through the attained numerical values of the parameters appearing in a proposed empirical model characterizing shear viscosity of body lotions. © 2016 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Study on a novel panel support concept for radio telescopes with active surface

NASA Astrophysics Data System (ADS)

Yang, Dehua; Zhou, Guohua; Okoh, Daniel; Li, Guoping; Cheng, Jingquan

2010-07-01

Generally, panels of radio telescopes are mainly shaped in trapezoid and each is supported/positioned by four adjustors beneath its vertexes. Such configuration of panel supporting system is essentially hyper-static, and the panel is overconstrained from a kinematic point of view. When the panel is to be adjusted and/or actuated, it will suffer stress from its adjusters and hence its shape is to be distorted. This situation is not desirable for high precision panels, such as glass based panels especially used for sub-millimeter and shorter wavelength telescopes with active optics/active panel technology. This paper began with a general overview of panel patterns and panel supports of existing radio telescopes. Thereby, we proposed a preferable master-slave active surface concept for triangular and/or hexagonal panel pattern. In addition, we carry out panel error sensitivity analysis for all the 6 degrees of freedom (DOF) of a panel to identify what DOFs are most sensitive for an active surface. And afterwards, based on the error sensitivity analysis, we suggested an innovative parallel-series concept hexapod well fitted for an active panel to correct for all of its 6 rigid errors. A demonstration active surface using the master-slave concept and the hexapod manifested a great save in cost, where only 486 precision actuators are needed for 438 panels, which is 37% of those actuators needed by classic segmented mirror active optics. Further, we put forward a swaying-arm based design concept for the related connecting joints between panels, which ensures that all the panels attached on to it free from over-constraints when they are positioned and/or actuated. Principle and performance of the swaying-arm connecting mechanism are elaborated before a practical cablemesh based prototype active surface is presented with comprehensive finite element analysis and simulation.

Coupled Electro-Magneto-Mechanical-Acoustic Analysis Method Developed by Using 2D Finite Element Method for Flat Panel Speaker Driven by Magnetostrictive-Material-Based Actuator

NASA Astrophysics Data System (ADS)

Yoo, Byungjin; Hirata, Katsuhiro; Oonishi, Atsurou

In this study, a coupled analysis method for flat panel speakers driven by giant magnetostrictive material (GMM) based actuator was developed. The sound field produced by a flat panel speaker that is driven by a GMM actuator depends on the vibration of the flat panel, this vibration is a result of magnetostriction property of the GMM. In this case, to predict the sound pressure level (SPL) in the audio-frequency range, it is necessary to take into account not only the magnetostriction property of the GMM but also the effect of eddy current and the vibration characteristics of the actuator and the flat panel. In this paper, a coupled electromagnetic-structural-acoustic analysis method is presented; this method was developed by using the finite element method (FEM). This analysis method is used to predict the performance of a flat panel speaker in the audio-frequency range. The validity of the analysis method is verified by comparing with the measurement results of a prototype speaker.

Assessment of Intelligent Tutoring Systems Technologies and Opportunities (Evaluation et opportunites des technologies des systemes de tutorat intelligents)

DTIC Science & Technology

2018-01-01

His research designs adaptive systems for online content, by integrating research in psychology and education, human- ANNEX A − INTELLIGENT TUTORING...related scientific activities that include systems engineering, operational research and analysis, synthesis, integration and validation of knowledge...System Analysis and Studies Panel • SCI Systems Concepts and Integration Panel • SET Sensors and Electronics Technology Panel These Panels and Group

POSTOP: Postbuckled open-stiffener optimum panels-theory and capability

NASA Technical Reports Server (NTRS)

Dickson, J. N.; Biggers, S. B.

1984-01-01

The computer program POSTOP was developed to serve as an aid in the analysis and sizing of stiffened composite panels that are loaded in the postbuckling regime. A comprehensive set of analysis routines was coupled to a widely used optimization program to produce this sizing code. POSTOP is intended for the preliminary design of metal or composite panels with open-section stiffeners, subjected to multiple combined biaxial compression (or tension), shear and normal pressure load cases. Longitudinal compression, however, is assumed to be the dominant loading. Temperature, initial bow eccentricity and load eccentricity effects are included. The panel geometry is assumed to be repetitive over several bays in the longitudinal (stiffener) direction as well as in the transverse direction. Analytical routines are included to compute panel stiffnesses, strains, local and panel buckling loads, and skin/stiffener interface stresses. The resulting program is applicable to stiffened panels as commonly used in fuselage, wing, or empennage structures. The analysis procedures and rationale for the assumptions used therein are described in detail.

Flutter Research on Skin Panels

NASA Technical Reports Server (NTRS)

Kordes, Eldon E.; Tuovila, Weimer J.; Guy, Lawrence D.

1960-01-01

Representative experimental results are presented to show the current status of the panel flutter problem. Results are presented for unstiffened rectangular panels and for rectangular panels stiffened by corrugated backing. Flutter boundaries are established for all types of panels when considered on the basis of equivalent isotropic plates. The effects of Mach number, differential pressure, and aerodynamic heating on panel flutter are discussed. A flutter analysis of orthotropic panels is presented in the appendix.

THE RESEARCH TRIANGLE PARK PARTICULATE MATTER PANEL STUDY: MODELING AMBIENT SOURCE CONTRIBUTION TO PERSONAL AND RESIDENTIAL PM MASS CONCENTRATIONS

EPA Science Inventory

The Research Triangle Park (RTP) Particulate Matter (PM) Panel Study represented a one-year investigation of personal, residential and ambient PM mass concentrations across distances as large as 70 km in central North Carolina. One of the primary goals of this effort was to est...

Estimating burden and disease costs of exposure to endocrine-disrupting chemicals in the European union.

PubMed

Trasande, Leonardo; Zoeller, R Thomas; Hass, Ulla; Kortenkamp, Andreas; Grandjean, Philippe; Myers, John Peterson; DiGangi, Joseph; Bellanger, Martine; Hauser, Russ; Legler, Juliette; Skakkebaek, Niels E; Heindel, Jerrold J

2015-04-01

Rapidly increasing evidence has documented that endocrine-disrupting chemicals (EDCs) contribute substantially to disease and disability. The objective was to quantify a range of health and economic costs that can be reasonably attributed to EDC exposures in the European Union (EU). A Steering Committee of scientists adapted the Intergovernmental Panel on Climate Change weight-of-evidence characterization for probability of causation based upon levels of available epidemiological and toxicological evidence for one or more chemicals contributing to disease by an endocrine disruptor mechanism. To evaluate the epidemiological evidence, the Steering Committee adapted the World Health Organization Grading of Recommendations Assessment, Development and Evaluation (GRADE) Working Group criteria, whereas the Steering Committee adapted definitions recently promulgated by the Danish Environmental Protection Agency for evaluating laboratory and animal evidence of endocrine disruption. Expert panels used the Delphi method to make decisions on the strength of the data. Expert panels achieved consensus at least for probable (>20%) EDC causation for IQ loss and associated intellectual disability, autism, attention-deficit hyperactivity disorder, childhood obesity, adult obesity, adult diabetes, cryptorchidism, male infertility, and mortality associated with reduced testosterone. Accounting for probability of causation and using the midpoint of each range for probability of causation, Monte Carlo simulations produced a median cost of €157 billion (or $209 billion, corresponding to 1.23% of EU gross domestic product) annually across 1000 simulations. Notably, using the lowest end of the probability range for each relationship in the Monte Carlo simulations produced a median range of €109 billion that differed modestly from base case probability inputs. EDC exposures in the EU are likely to contribute substantially to disease and dysfunction across the life course with costs in the hundreds of billions of Euros per year. These estimates represent only those EDCs with the highest probability of causation; a broader analysis would have produced greater estimates of burden of disease and costs.

Estimating Burden and Disease Costs of Exposure to Endocrine-Disrupting Chemicals in the European Union

PubMed Central

Zoeller, R. Thomas; Hass, Ulla; Kortenkamp, Andreas; Grandjean, Philippe; Myers, John Peterson; DiGangi, Joseph; Bellanger, Martine; Hauser, Russ; Legler, Juliette; Skakkebaek, Niels E.; Heindel, Jerrold J.

2015-01-01

Context: Rapidly increasing evidence has documented that endocrine-disrupting chemicals (EDCs) contribute substantially to disease and disability. Objective: The objective was to quantify a range of health and economic costs that can be reasonably attributed to EDC exposures in the European Union (EU). Design: A Steering Committee of scientists adapted the Intergovernmental Panel on Climate Change weight-of-evidence characterization for probability of causation based upon levels of available epidemiological and toxicological evidence for one or more chemicals contributing to disease by an endocrine disruptor mechanism. To evaluate the epidemiological evidence, the Steering Committee adapted the World Health Organization Grading of Recommendations Assessment, Development and Evaluation (GRADE) Working Group criteria, whereas the Steering Committee adapted definitions recently promulgated by the Danish Environmental Protection Agency for evaluating laboratory and animal evidence of endocrine disruption. Expert panels used the Delphi method to make decisions on the strength of the data. Results: Expert panels achieved consensus at least for probable (>20%) EDC causation for IQ loss and associated intellectual disability, autism, attention-deficit hyperactivity disorder, childhood obesity, adult obesity, adult diabetes, cryptorchidism, male infertility, and mortality associated with reduced testosterone. Accounting for probability of causation and using the midpoint of each range for probability of causation, Monte Carlo simulations produced a median cost of €157 billion (or $209 billion, corresponding to 1.23% of EU gross domestic product) annually across 1000 simulations. Notably, using the lowest end of the probability range for each relationship in the Monte Carlo simulations produced a median range of €109 billion that differed modestly from base case probability inputs. Conclusions: EDC exposures in the EU are likely to contribute substantially to disease and dysfunction across the life course with costs in the hundreds of billions of Euros per year. These estimates represent only those EDCs with the highest probability of causation; a broader analysis would have produced greater estimates of burden of disease and costs. PMID:25742516

The Reconstruction and Failure Analysis of The Space Shuttle Columbia

NASA Technical Reports Server (NTRS)

Russell, Richard W.

2010-01-01

This viewgraph presentation describes a very detailed reconstruction plan and failure analysis of The Space Shuttle Columbia accident. The contents include: 1) STS-107 Timeline; 2) Foam Impact; 3) Recovery; 4) Reconstruction; 5) Reconstruction Plan; 6) Reconstruction Hanger; 7) Pathfinders; 8) Aluminum Pathfinder; 9) Early Analysis - Left MLG Door Area; 10) Emphasis Switched to Left Hand Wing Leading Edge; 11) Wing Leading Edge Subsystem (LESS); 12) 3D Reconstruction of Left WLE; 13) Left Wing Tile Table; 14) LESS Observations; 15) Left Hand Wing Debris Points to RCC 8/9 - Slumped Tile; 16) Reconstructed View of LC/P 9 tile with I/B Tile; 17) Reconstructed View of Lower C/P 9 Tile; 18) Carrier Panel 8 - Upper; 19) Left Hand Wing Debris Points to RCC 8/9 - Erosion and RCC with attach hole intact; 20) Erosion on Panel 8 Upper Outboard Rib; 21) RCC Panels 8 & 9 Erosion Features; 22) Slumping Source for Carrier Panel 9 Tile was Revealed; 23) Debris Indicated Highest Probability Initiation Site; 24) Left Hand Wing Debris Points to RCC 8/9- Metallic Deposits; 25) Relative Metallic Deposition on L/H Wing Materials; 26) Metallic Deposit Example, LH RCC 8; 27) High Level Questions; 28) Analysis Plan Challenges; 29) Analysis Techniques; 30) Analysis Approach; 31) RCC Panel 8 Erosion Features; 32) Radiographic Features; 33) Radiography WLE LH Panel 8; 34) LH RCC 8 Upper Apex; 35) LH RCC 8 - Deposit Feature: Thick Tear Shaped; 36) LH RCC 8 - Deposit Feature: Thick Globules; 37) LH RCC 8 - Deposit Feature: Spheroids; 38) LH RCC 8 - Deposit Feature: Uniform Deposit; 39) Significant Findings - Sampling All Other panels; 40) Proposed Breach Location and Plasma Flow; 41) Corroborating Information - RCC Panel Debris Locations; 42) Corroborating Information - LH OMS Pod Analysis; 43) Corroborating Information - Impact Testing; and 44) Overall Forensic Conclusions.

Design, Optimization, and Evaluation of A1-2139 Compression Panel with Integral T-Stiffeners

NASA Technical Reports Server (NTRS)

Mulani, Sameer B.; Havens, David; Norris, Ashley; Bird, R. Keith; Kapania, Rakesh K.; Olliffe, Robert

2012-01-01

A T-stiffened panel was designed and optimized for minimum mass subjected to constraints on buckling load, yielding, and crippling or local stiffener failure using a new analysis and design tool named EBF3PanelOpt. The panel was designed for a compression loading configuration, a realistic load case for a typical aircraft skin-stiffened panel. The panel was integrally machined from 2139 aluminum alloy plate and was tested in compression. The panel was loaded beyond buckling and strains and out-of-plane displacements were extracted from 36 strain gages and one linear variable displacement transducer. A digital photogrammetric system was used to obtain full field displacements and strains on the smooth (unstiffened) side of the panel. The experimental data were compared with the strains and out-of-plane deflections from a high-fidelity nonlinear finite element analysis.

Structural efficiency study of composite wing rib structures

NASA Technical Reports Server (NTRS)

Swanson, Gary D.; Gurdal, Zafer; Starnes, James H., Jr.

1988-01-01

A series of short stiffened panel designs which may be applied to a preliminary design assessment of an aircraft wing rib is presented. The computer program PASCO is used as the primary design and analysis tool to assess the structural efficiency and geometry of a tailored corrugated panel, a corrugated panel with a continuous laminate, a hat stiffened panel, a blade stiffened panel, and an unstiffened flat plate. To correct some of the shortcomings in the PASCO analysis when shear is present, a two step iterative process using the computer program VICON is used. The loadings considered include combinations of axial compression, shear, and lateral pressure. The loading ranges considered are broad enough such that the designs presented may be applied to other stiffened panel applications. An assessment is made of laminate variations, increased spacing, and nonoptimum geometric variations, including a beaded panel, on the design of the panels.

General aviation aircraft interior noise problem: Some suggested solutions

NASA Technical Reports Server (NTRS)

Roskam, J.; Navaneethan, R.

1984-01-01

Laboratory investigation of sound transmission through panels and the use of modern data analysis techniques applied to actual aircraft is used to determine methods to reduce general aviation interior noise. The experimental noise reduction characteristics of stiffened flat and curved panels with damping treatment are discussed. The experimental results of double-wall panels used in the general aviation industry are given. The effects of skin panel material, fiberglass insulation and trim panel material on the noise reduction characteristics of double-wall panels are investigated. With few modifications, the classical sound transmission theory can be used to design the interior noise control treatment of aircraft. Acoustic intensity and analysis procedures are included.

Experimental and finite element investigation of the buckling characteristics of a beaded skin panel for a hypersonic aircraft. Ph.D. Thesis. Final Report

NASA Technical Reports Server (NTRS)

Siegel, W. H.

1978-01-01

As part of NASA's continuing research into hypersonics and 85 square foot hypersonic wing test section of a proposed hypersonic research airplane was laboratory tested. The project reported on in this paper has carried the hypersonic wing test structure project one step further by testing a single beaded panel to failure. The primary interest was focused upon the buckling characteristics of the panel under pure compression with boundary conditions similar to those found in a wing mounted condition. Three primary phases of analysis are included in the report. These phases include: experimental testing of the beaded panel to failure; finite element structural analysis of the beaded panel with the computer program NASTRAN; a summary of the semiclassical buckling equations for the beaded panel under purely compressive loads. Comparisons between each of the analysis methods are also included.

Study of advanced composite structural design concepts for an arrow wing supersonic cruise configuration

NASA Technical Reports Server (NTRS)

Turner, M. J.; Grande, D. L.

1978-01-01

Based on estimated graphite and boron fiber properties, allowable stresses and strains were established for advanced composite materials. Stiffened panel and conventional sandwich panel concepts were designed and analyzed, using graphite/polyimide and boron/polyimide materials. The conventional sandwich panel was elected as the structural concept for the modified wing structure. Upper and lower surface panels of the arrow wing structure were then redesigned, using high strength graphite/polyimide sandwich panels, retaining the titanium spars and ribs from the prior study. The ATLAS integrated analysis and design system was used for stress analysis and automated resizing of surface panels. Flutter analysis of the hybrid structure showed a significant decrease in flutter speed relative to the titanium wing design. The flutter speed was increased to that of the titanium design by selective increase in laminate thickness and by using graphite fibers with properties intermediate between high strength and high modulus values.

Laser welded steel sandwich panel bridge deck development : finite element analysis and stake weld strength tests.

DOT National Transportation Integrated Search

2009-09-01

This report summarizes the analysis of laser welded steel sandwich panels for use in bridge structures and : static testing of laser stake welded lap shear coupons. Steel sandwich panels consist of two face sheets : connected by a relatively low-dens...

Analysis and Tests of Reinforced Carbon-Epoxy/Foam-Core Sandwich Panels with Cutouts

NASA Technical Reports Server (NTRS)

Baker, Donald J.; Rogers, Charles

1996-01-01

The results of a study of a low-cost structurally efficient minimum-gage shear-panel design that can be used in light helicopters are presented. The shear-panel design is based on an integrally stiffened syntactic-foam stabilized-skin with an all-bias-ply tape construction for stabilized-skin concept with an all-bias-ply tape construction for the skins. This sandwich concept is an economical way to increase the panel bending stiffness weight penalty. The panels considered in the study were designed to be buckling resistant up to 100 lbs/in. of shear load and to have an ultimate strength of 300 lbs/in. The panel concept uses unidirectional carbon-epoxy tape on a syntactic adhesive as a stiffener that is co-cured with the skin and is an effective concept for improving panel buckling strength. The panel concept also uses pultruded carbon-epoxy rods embedded in a syntactic adhesive and over-wrapped with a bias-ply carbon-epoxy tape to form a reinforcing beam which is an effective method for redistributing load around rectangular cutout. The buckling strength of the reinforced panels is 83 to 90 percent of the predicted buckling strength based on a linear buckling analysis. The maximum experimental deflection exceeds the maximum deflection predicted by a nonlinear analysis by approximately one panel thickness. The failure strength of the reinforced panels was two and a half to seven times of the buckling strength. This efficient shear-panel design concept exceeds the required ultimate strength requirement of 300 lbs/in by more than 100 percent.

Size Effects in Impact Damage of Composite Sandwich Panels

NASA Technical Reports Server (NTRS)

Dobyns, Alan; Jackson, Wade

2003-01-01

Panel size has a large effect on the impact response and resultant damage level of honeycomb sandwich panels. It has been observed during impact testing that panels of the same design but different panel sizes will show large differences in damage when impacted with the same impact energy. To study this effect, a test program was conducted with instrumented impact testing of three different sizes of sandwich panels to obtain data on panel response and residual damage. In concert with the test program. a closed form analysis method was developed that incorporates the effects of damage on the impact response. This analysis method will predict both the impact response and the residual damage of a simply-supported sandwich panel impacted at any position on the panel. The damage is incorporated by the use of an experimental load-indentation curve obtained for the face-sheet/honeycomb and indentor combination under study. This curve inherently includes the damage response and can be obtained quasi-statically from a rigidly-backed specimen or a specimen with any support conditions. Good correlation has been obtained between the test data and the analysis results for the maximum force and residual indentation. The predictions can be improved by using a dynamic indentation curve. Analyses have also been done using the MSC/DYTRAN finite element code.

Obesity, diabetes, and associated costs of exposure to endocrine-disrupting chemicals in the European Union.

PubMed

Legler, Juliette; Fletcher, Tony; Govarts, Eva; Porta, Miquel; Blumberg, Bruce; Heindel, Jerrold J; Trasande, Leonardo

2015-04-01

Obesity and diabetes are epidemic in the European Union (EU). Exposure to endocrine-disrupting chemicals (EDCs) is increasingly recognized as a contributor, independent of diet and physical activity. The objective was to estimate obesity, diabetes, and associated costs that can be reasonably attributed to EDC exposures in the EU. An expert panel evaluated evidence for probability of causation using weight-of-evidence characterization adapted from that applied by the Intergovernmental Panel on Climate Change. Exposure-response relationships and reference levels were evaluated for relevant EDCs, and biomarker data were organized from peer-reviewed studies to represent European exposure and burden of disease. Cost estimation as of 2010 utilized published cost estimates for childhood obesity, adult obesity, and adult diabetes. Setting, Patients and Participants, and Intervention: Cost estimation was performed from the societal perspective. The panel identified a 40% to 69% probability of dichlorodiphenyldichloroethylene causing 1555 cases of overweight at age 10 (sensitivity analysis: 1555-5463) in 2010 with associated costs of €24.6 million (sensitivity analysis: €24.6-86.4 million). A 20% to 39% probability was identified for dichlorodiphenyldichloroethylene causing 28 200 cases of adult diabetes (sensitivity analysis: 28 200-56 400) with associated costs of €835 million (sensitivity analysis: €835 million-16.6 billion). The panel also identified a 40% to 69% probability of phthalate exposure causing 53 900 cases of obesity in older women and €15.6 billion in associated costs. Phthalate exposure was also found to have a 40% to 69% probability of causing 20 500 new-onset cases of diabetes in older women with €607 million in associated costs. Prenatal bisphenol A exposure was identified to have a 20% to 69% probability of causing 42 400 cases of childhood obesity, with associated lifetime costs of €1.54 billion. EDC exposures in the EU contribute substantially to obesity and diabetes, with a moderate probability of >€18 billion costs per year. This is a conservative estimate; the results emphasize the need to control EDC exposures.

Obesity, Diabetes, and Associated Costs of Exposure to Endocrine-Disrupting Chemicals in the European Union

PubMed Central

Legler, Juliette; Fletcher, Tony; Govarts, Eva; Porta, Miquel; Blumberg, Bruce; Heindel, Jerrold J.

2015-01-01

Context: Obesity and diabetes are epidemic in the European Union (EU). Exposure to endocrine-disrupting chemicals (EDCs) is increasingly recognized as a contributor, independent of diet and physical activity. Objective: The objective was to estimate obesity, diabetes, and associated costs that can be reasonably attributed to EDC exposures in the EU. Design: An expert panel evaluated evidence for probability of causation using weight-of-evidence characterization adapted from that applied by the Intergovernmental Panel on Climate Change. Exposure-response relationships and reference levels were evaluated for relevant EDCs, and biomarker data were organized from peer-reviewed studies to represent European exposure and burden of disease. Cost estimation as of 2010 utilized published cost estimates for childhood obesity, adult obesity, and adult diabetes. Setting, Patients and Participants, and Intervention: Cost estimation was performed from the societal perspective. Results: The panel identified a 40% to 69% probability of dichlorodiphenyldichloroethylene causing 1555 cases of overweight at age 10 (sensitivity analysis: 1555–5463) in 2010 with associated costs of €24.6 million (sensitivity analysis: €24.6–86.4 million). A 20% to 39% probability was identified for dichlorodiphenyldichloroethylene causing 28 200 cases of adult diabetes (sensitivity analysis: 28 200–56 400) with associated costs of €835 million (sensitivity analysis: €835 million–16.6 billion). The panel also identified a 40% to 69% probability of phthalate exposure causing 53 900 cases of obesity in older women and €15.6 billion in associated costs. Phthalate exposure was also found to have a 40% to 69% probability of causing 20 500 new-onset cases of diabetes in older women with €607 million in associated costs. Prenatal bisphenol A exposure was identified to have a 20% to 69% probability of causing 42 400 cases of childhood obesity, with associated lifetime costs of €1.54 billion. Conclusions: EDC exposures in the EU contribute substantially to obesity and diabetes, with a moderate probability of >€18 billion costs per year. This is a conservative estimate; the results emphasize the need to control EDC exposures. PMID:25742518

Experimental modal analysis of the fuselage panels of an Aero Commander aircraft

NASA Technical Reports Server (NTRS)

Geisler, D.

1981-01-01

The reduction of interior noise in light aircraft was investigated with emphasis the thin fuselage sidewall. The approach used is theoretical and involves modeling of the sidewall panels and stiffeners. Experimental data obtained from tests investigating the effects of mass and stiffness treatments to the sidewalls are presented. The dynamic characteristics of treated panels are contrasted with the untreated sidewall panels using experimental modal analysis techniques. The results include the natural frequencies, modal dampling, and mode shapes of selected panels. Frequency response functions, data relating to the global fuselage response, and acoustic response are also presented.

Test/semi-empirical analysis of a carbon/epoxy fabric stiffened panel

NASA Technical Reports Server (NTRS)

Spier, E. E.; Anderson, J. A.

1990-01-01

The purpose of this work-in-progress is to present a semi-empirical analysis method developed to predict the buckling and crippling loads of carbon/epoxy fabric blade stiffened panels in compression. This is a hand analysis method comprised of well known, accepted techniques, logical engineering judgements, and experimental data that results in conservative solutions. In order to verify this method, a stiffened panel was fabricated and tested. Both the best and analysis results are presented.

Convective and global stability analysis of a Mach 5.8 boundary layer grazing a compliant surface

NASA Astrophysics Data System (ADS)

Dettenrieder, Fabian; Bodony, Daniel

2016-11-01

Boundary layer transition on high-speed vehicles is expected to be affected by unsteady surface compliance. The stability properties of a Mach 5.8 zero-pressure-gradient laminar boundary layer grazing a nominally-flat thermo-mechanically compliant panel is considered. The linearized compressible Navier-Stokes equations describe small amplitude disturbances in the fluid while the panel deformations are described by the Kirchhoff-Love plate equation and its thermal state by the transient heat equation. Compatibility conditions that couple disturbances in the fluid to those in the solid yield simple algebraic and robin boundary conditions for the velocity and thermal states, respectively. A local convective stability analysis shows that the panel can modify both the first and second Mack modes when, for metallic-like panels, the panel thickness exceeds the lengthscale δ99 Rex- 0 . 5 . A global stability analysis, which permits finite panel lengths with clamped-clamped boundary conditions, shows a rich eigenvalue spectrum with several branches. Unstable modes are found with streamwise-growing panel deformations leading to Mach wave-type radiation. Stable global modes are also found and have distinctly different panel modes but similar radiation patterns. Air Force Office of Scientific Research.

Future Defence Budget Constraints: Challenges and Opportunities (Contraintes futures sur les budgets de defense: Defis et opportunites)

DTIC Science & Technology

2016-12-01

collaborative effort is addressed by six Technical Panels who manage a wide range of scientific research activities, a Group specialising in modelling and...HFM Human Factors and Medicine Panel • IST Information Systems Technology Panel • NMSG NATO Modelling and Simulation Group • SAS System Analysis...and Studies Panel • SCI Systems Concepts and Integration Panel • SET Sensors and Electronics Technology Panel These Panels and Group are the

Modal analysis and acoustic transmission through offset-core honeycomb sandwich panels

NASA Astrophysics Data System (ADS)

Mathias, Adam Dustin

The work presented in this thesis is motivated by an earlier research that showed that double, offset-core honeycomb sandwich panels increased thermal resistance and, hence, decreased heat transfer through the panels. This result lead to the hypothesis that these panels could be used for acoustic insulation. Using commercial finite element modeling software, COMSOL Multiphysics, the acoustical properties, specifically the transmission loss across a variety of offset-core honeycomb sandwich panels, is studied for the case of a plane acoustic wave impacting the panel at normal incidence. The transmission loss results are compared with those of single-core honeycomb panels with the same cell sizes. The fundamental frequencies of the panels are also computed in an attempt to better understand the vibrational modes of these particular sandwich-structured panels. To ensure that the finite element analysis software is adequate for the task at hand, two relevant benchmark problems are solved and compared with theory. Results from these benchmark results compared well to those obtained from theory. Transmission loss results from the offset-core honeycomb sandwich panels show increased transmission loss, especially for large cell honeycombs when compared to single-core honeycomb panels.

The Effect of Differential Incentives on Attrition Bias: Evidence from the PASS Wave 3 Incentive Experiment

ERIC Educational Resources Information Center

Felderer, Barbara; Müller, Gerrit; Kreuter, Frauke; Winter, Joachim

2018-01-01

Respondent incentives are widely used to increase response rates, but their effect on nonresponse bias has not been researched as much. To contribute to the research, we analyze an incentive experiment embedded within the third wave of the German household panel survey "Panel Labor Market and Social Security" conducted by the German…

Targeted mutation screening panels expose systematic population bias in detection of cystic fibrosis risk.

PubMed

Lim, Regine M; Silver, Ari J; Silver, Maxwell J; Borroto, Carlos; Spurrier, Brett; Petrossian, Tanya C; Larson, Jessica L; Silver, Lee M

2016-02-01

Carrier screening for mutations contributing to cystic fibrosis (CF) is typically accomplished with panels composed of variants that are clinically validated primarily in patients of European descent. This approach has created a static genetic and phenotypic profile for CF. An opportunity now exists to reevaluate the disease profile of CFTR at a global population level. CFTR allele and genotype frequencies were obtained from a nonpatient cohort with more than 60,000 unrelated personal genomes collected by the Exome Aggregation Consortium. Likely disease-contributing mutations were identified with the use of public database annotations and computational tools. We identified 131 previously described and likely pathogenic variants and another 210 untested variants with a high probability of causing protein damage. None of the current genetic screening panels or existing CFTR mutation databases covered a majority of deleterious variants in any geographical population outside of Europe. Both clinical annotation and mutation coverage by commercially available targeted screening panels for CF are strongly biased toward detection of reproductive risk in persons of European descent. South and East Asian populations are severely underrepresented, in part because of a definition of disease that preferences the phenotype associated with European-typical CFTR alleles.

Final Report for Dynamic Models for Causal Analysis of Panel Data. Methodological Overview. Part II, Chapter 1.

ERIC Educational Resources Information Center

Hannan, Michael T.

This technical document, part of a series of chapters described in SO 011 759, describes a basic model of panel analysis used in a study of the causes of institutional and structural change in nations. Panel analysis is defined as a record of state occupancy of a sample of units at two or more points in time; for example, voters disclose voting…

Progressive Failure Analysis of Composite Stiffened Panels

NASA Technical Reports Server (NTRS)

Bednarcyk, Brett A.; Yarrington, Phillip W.; Collier, Craig S.; Arnold, Steven M.

2006-01-01

A new progressive failure analysis capability for stiffened composite panels has been developed based on the combination of the HyperSizer stiffened panel design/analysis/optimization software with the Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC). MAC/GMC discretizes a composite material s microstructure into a number of subvolumes and solves for the stress and strain state in each while providing the homogenized composite properties as well. As a result, local failure criteria may be employed to predict local subvolume failure and the effects of these local failures on the overall composite response. When combined with HyperSizer, MAC/GMC is employed to represent the ply level composite material response within the laminates that constitute a stiffened panel. The effects of local subvolume failures can then be tracked as loading on the stiffened panel progresses. Sample progressive failure results are presented at both the composite laminate and the composite stiffened panel levels. Deformation and failure model predictions are compared with experimental data from the World Wide Failure Exercise for AS4/3501-6 graphite/epoxy laminates.

A critical examination of the evidence relating high fructose corn syrup and weight gain.

PubMed

Forshee, Richard A; Storey, Maureen L; Allison, David B; Glinsmann, Walter H; Hein, Gayle L; Lineback, David R; Miller, Sanford A; Nicklas, Theresa A; Weaver, Gary A; White, John S

2007-01-01

The use of high fructose corn syrup (HFCS) has increased over the past several decades in the United States while overweight and obesity rates have risen dramatically. Some scientists hypothesize that HFCS consumption has uniquely contributed to the increasing mean body mass index (BMI) of the U.S. population. The Center for Food, Nutrition, and Agriculture Policy convened an expert panel to discuss the published scientific literature examining the relationship between consumption of HFCS or "soft drinks" (proxy for HFCS) and weight gain. The authors conducted original analysis to address certain gaps in the literature. Evidence from ecological studies linking HFCS consumption with rising BMI rates is unreliable. Evidence from epidemiologic studies and randomized controlled trials is inconclusive. Studies analyzing the differences between HFCS and sucrose consumption and their contributions to weight gain do not exist. HFCS and sucrose have similar monosaccharide compositions and sweetness values. The fructose:glucose (F:G) ratio in the U.S. food supply has not appreciably changed since the introduction of HFCS in the 1960s. It is unclear why HFCS would affect satiety or absorption and metabolism of fructose any differently than would sucrose. Based on the currently available evidence, the expert panel concluded that HFCS does not appear to contribute to overweight and obesity any differently than do other energy sources. Research recommendations were made to improve our understanding of the association of HFCS and weight gain.

Theoretical investigation of flutter of two-dimensional flat panels with one surface exposed to supersonic potential flow

NASA Technical Reports Server (NTRS)

Nelson, Herbert C; Cunningham, Herbert J

1956-01-01

A Rayleigh type analysis involving chosen modes of the panel as degrees of freedom is used to treat the flutter of a two-dimensional flat panel supported at its leading and trailing edges and subjected to a middle-plane tensile force. The panel has a supersonic stream passing over its upper surface and still air below. The aerodynamic forces due to the supersonic stream are obtained from the theory for linearized two-dimensional unsteady flow and the forces due to the still air are obtained from acoustical theory. In order to study the effect of increasing the number of modes in the analysis, two and then four modes are employed. The modes used are the first four natural modes of the panel in a vacuum with no tensile force acting. The analysis includes these variables: Mach number, structural damping, tensile force, density of the still air, and edge fixity (clamped and pinned). For certain combinations of these variables, stability boundaries are obtained which can be used to determine the panel thickness required to prevent flutter for any panel material and altitude.

The Efficiency of Split Panel Designs in an Analysis of Variance Model

PubMed Central

Wang, Wei-Guo; Liu, Hai-Jun

2016-01-01

We consider split panel design efficiency in analysis of variance models, that is, the determination of the cross-sections series optimal proportion in all samples, to minimize parametric best linear unbiased estimators of linear combination variances. An orthogonal matrix is constructed to obtain manageable expression of variances. On this basis, we derive a theorem for analyzing split panel design efficiency irrespective of interest and budget parameters. Additionally, relative estimator efficiency based on the split panel to an estimator based on a pure panel or a pure cross-section is present. The analysis shows that the gains from split panel can be quite substantial. We further consider the efficiency of split panel design, given a budget, and transform it to a constrained nonlinear integer programming. Specifically, an efficient algorithm is designed to solve the constrained nonlinear integer programming. Moreover, we combine one at time designs and factorial designs to illustrate the algorithm’s efficiency with an empirical example concerning monthly consumer expenditure on food in 1985, in the Netherlands, and the efficient ranges of the algorithm parameters are given to ensure a good solution. PMID:27163447

A novel strategy to increase separated electron-hole dipoles in commercial Si based solar panel to assist photovoltaic effect

NASA Astrophysics Data System (ADS)

Feng, Yefeng; He, Cheng-En; Xu, Zhichao; Hu, Jianbing; Peng, Cheng

2018-01-01

Interface induced polarization has been found to have a significant impact on dielectric properties of 2-2 type polymer composites bearing Si based semi-conducting ceramic sheets. Inherent overall polarity of polymer layers in 2-2 composites has been verified to be closely connected with interface effect and achieved permittivity in composites. In present work, conducting performances of monocrystalline Si sheets coated by varied high polarity material layers were deeply researched. The positive results inspired us to propose a novel strategy to improve separated electron-hole dipoles in commercial Si based solar cell panel for assisting photovoltaic effect, based on strong interface induced polarization. Conducting features of solar panels coated by two different high polarity polymer layers were detected to be greatly elevated compared with solar panel standalone, thanks to interface induced polarization between panel and polymer. Polymer coating with higher polarity would lead to more separated electron-hole dipole pairs in solar panel contributing to higher conductivity of panel. Valid synergy of interface effect and photovoltaic effect was based on their unidirectional traits of electron transfer. Dielectric properties of solar panels in composites further confirmed that strategy. This work might provide a facile route to prepare promising Si based solar panels with higher photoelectric conversion efficiency by enhancing interface induced polarization between panel and polymer coating.

Probabilistic Structural Evaluation of Uncertainties in Radiator Sandwich Panel Design

NASA Technical Reports Server (NTRS)

Kuguoglu, Latife; Ludwiczak, Damian

2006-01-01

The Jupiter Icy Moons Orbiter (JIMO) Space System is part of the NASA's Prometheus Program. As part of the JIMO engineering team at NASA Glenn Research Center, the structural design of the JIMO Heat Rejection Subsystem (HRS) is evaluated. An initial goal of this study was to perform sensitivity analyses to determine the relative importance of the input variables on the structural responses of the radiator panel. The desire was to let the sensitivity analysis information identify the important parameters. The probabilistic analysis methods illustrated here support this objective. The probabilistic structural performance evaluation of a HRS radiator sandwich panel was performed. The radiator panel structural performance was assessed in the presence of uncertainties in the loading, fabrication process variables, and material properties. The stress and displacement contours of the deterministic structural analysis at mean probability was performed and results presented. It is followed by a probabilistic evaluation to determine the effect of the primitive variables on the radiator panel structural performance. Based on uncertainties in material properties, structural geometry and loading, the results of the displacement and stress analysis are used as an input file for the probabilistic analysis of the panel. The sensitivity of the structural responses, such as maximum displacement and maximum tensile and compressive stresses of the facesheet in x and y directions and maximum VonMises stresses of the tube, to the loading and design variables is determined under the boundary condition where all edges of the radiator panel are pinned. Based on this study, design critical material and geometric parameters of the considered sandwich panel are identified.

Burden of disease and costs of exposure to endocrine disrupting chemicals in the European Union: an updated analysis.

PubMed

Trasande, L; Zoeller, R T; Hass, U; Kortenkamp, A; Grandjean, P; Myers, J P; DiGangi, J; Hunt, P M; Rudel, R; Sathyanarayana, S; Bellanger, M; Hauser, R; Legler, J; Skakkebaek, N E; Heindel, J J

2016-07-01

A previous report documented that endocrine disrupting chemicals contribute substantially to certain forms of disease and disability. In the present analysis, our main objective was to update a range of health and economic costs that can be reasonably attributed to endocrine disrupting chemical exposures in the European Union, leveraging new burden and disease cost estimates of female reproductive conditions from accompanying report. Expert panels evaluated the epidemiologic evidence, using adapted criteria from the WHO Grading of Recommendations Assessment, Development and Evaluation Working Group, and evaluated laboratory and animal evidence of endocrine disruption using definitions recently promulgated by the Danish Environmental Protection Agency. The Delphi method was used to make decisions on the strength of the data. Expert panels consensus was achieved for probable (>20%) endocrine disrupting chemical causation for IQ loss and associated intellectual disability; autism; attention deficit hyperactivity disorder; endometriosis; fibroids; childhood obesity; adult obesity; adult diabetes; cryptorchidism; male infertility, and mortality associated with reduced testosterone. Accounting for probability of causation, and using the midpoint of each range for probability of causation, Monte Carlo simulations produced a median annual cost of €163 billion (1.28% of EU Gross Domestic Product) across 1000 simulations. We conclude that endocrine disrupting chemical exposures in the EU are likely to contribute substantially to disease and dysfunction across the life course with costs in the hundreds of billions of Euros per year. These estimates represent only those endocrine disrupting chemicals with the highest probability of causation; a broader analysis would have produced greater estimates of burden of disease and costs. © 2016 American Society of Andrology and European Academy of Andrology.

Fracture Mechanics Analyses of the Slip-Side Joggle Regions of Wing-Leading Edge Panels

NASA Technical Reports Server (NTRS)

Raju, Ivatury S.; Knight, Norman F., Jr.; Song, Kyongchan; Phillips, Dawn R.

2010-01-01

The Space Shuttle Orbiter wing comprises of 22 leading edge panels on each side of the wing. These panels are part of the thermal protection system that protects the Orbiter wings from extreme heating that take place on the reentry in to the earth atmosphere. On some panels that experience extreme heating, liberation of silicon carbon (SiC) coating was observed on the slip side regions of the panels. Global structural and local fracture mechanics analyses were performed on these panels as a part of the root cause investigation of this coating liberation anomaly. The wing-leading-edge reinforced carbon-carbon (RCC) panels, Panel 9, T-seal 10, and Panel 10, are shown in Figure 1 and the progression of the stress analysis models is presented in Figure 2. The global structural analyses showed minimal interaction between adjacent panels and the T-seal that bridges the gap between the panels. A bounding uniform temperature is applied to a representative panel and the resulting stress distribution is examined. For this loading condition, the interlaminar normal stresses showed negligible variation in the chord direction and increased values in the vicinity of the slip-side joggle shoulder. As such, a representative span wise slice on the panel can be taken and the cross section can be analyzed using plane strain analysis.

Evaluation of Geopolymer Concrete for Rocket Test Facility Flame Deflectors

NASA Technical Reports Server (NTRS)

Allgood, Daniel C.; Montes, Carlos; Islam, Rashedul; Allouche, Erez

2014-01-01

The current paper presents results from a combined research effort by Louisiana Tech University (LTU) and NASA Stennis Space Center (SSC) to develop a new alumina-silicate based cementitious binder capable of acting as a high performance refractory material with low heat ablation rate and high early mechanical strength. Such a binder would represent a significant contribution to NASA's efforts to develop a new generation of refractory 'hot face' liners for liquid or solid rocket plume environments. This project was developed as a continuation of on-going collaborations between LTU and SSC, where test sections of a formulation of high temperature geopolymer binder were cast in the floor and walls of Test Stand E-1 Cell 3, an active rocket engine test stand flame trench. Additionally, geopolymer concrete panels were tested using the NASA-SSC Diagnostic Test Facility (DTF) thruster, where supersonic plume environments were generated on a 1ft wide x 2ft long x 6 inch deep refractory panel. The DTF operates on LOX/GH2 propellants producing a nominal thrust of 1,200 lbf and the combustion chamber conditions are Pc=625psig, O/F=6.0. Data collected included high speed video of plume/panel area and surface profiles (depth) of the test panels measured on a 1-inch by 1-inch giving localized erosion rates during the test. Louisiana Tech conducted a microstructure analysis of the geopolymer binder after the testing program to identify phase changes in the material.

Nonlinear Analysis and Post-Test Correlation for a Curved PRSEUS Panel

NASA Technical Reports Server (NTRS)

Gould, Kevin; Lovejoy, Andrew E.; Jegley, Dawn; Neal, Albert L.; Linton, Kim, A.; Bergan, Andrew C.; Bakuckas, John G., Jr.

2013-01-01

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept, developed by The Boeing Company, has been extensively studied as part of the National Aeronautics and Space Administration's (NASA s) Environmentally Responsible Aviation (ERA) Program. The PRSEUS concept provides a light-weight alternative to aluminum or traditional composite design concepts and is applicable to traditional-shaped fuselage barrels and wings, as well as advanced configurations such as a hybrid wing body or truss braced wings. Therefore, NASA, the Federal Aviation Administration (FAA) and The Boeing Company partnered in an effort to assess the performance and damage arrestments capabilities of a PRSEUS concept panel using a full-scale curved panel in the FAA Full-Scale Aircraft Structural Test Evaluation and Research (FASTER) facility. Testing was conducted in the FASTER facility by subjecting the panel to axial tension loads applied to the ends of the panel, internal pressure, and combined axial tension and internal pressure loadings. Additionally, reactive hoop loads were applied to the skin and frames of the panel along its edges. The panel successfully supported the required design loads in the pristine condition and with a severed stiffener. The panel also demonstrated that the PRSEUS concept could arrest the progression of damage including crack arrestment and crack turning. This paper presents the nonlinear post-test analysis and correlation with test results for the curved PRSEUS panel. It is shown that nonlinear analysis can accurately calculate the behavior of a PRSEUS panel under tension, pressure and combined loading conditions.

Pressure Testing of a Minimum Gauge PRSEUS Panel

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew J.; Rouse, Marshall; Linton, Kim A.; Li, Victor P.

2011-01-01

Advanced aircraft configurations that have been developed to increase fuel efficiency require advanced, novel structural concepts capable of handling the unique load conditions that arise. One such concept is the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) developed by the Boeing Company. The PRSEUS concept is being investigated by NASA s Environmentally Responsible Aviation (ERA) Program for use in a hybrid-wing body (HWB) aircraft. This paper summarizes the analysis and test of a PRSEUS panel subjected to internal pressure, the first such pressure test for this structural concept. The pressure panel used minimum gauge skin, with stringer and frame configurations consistent with previous PRSEUS tests. Analysis indicated that for the minimum gauge skin panel, the stringer locations exhibit fairly linear response, but the skin bays between the stringers exhibit nonlinear response. Excellent agreement was seen between nonlinear analysis and test results in the critical portion at the center of the panel. The pristine panel was capable of withstanding the required 18.4 psi pressure load condition without exhibiting any damage. The impacted panel was capable of withstanding a pressure load in excess of 28 psi before initial failure occurred at the center stringer, and the panel was capable of sustaining increased pressure load after the initial failure. This successful PRSEUS panel pressure panel test was a critical step in the building block approach for enabling the use of this advanced structural concept on future aircraft, such as the HWB.

Creating Good Employment Opportunities for the Rural Sector

PubMed Central

Foster, Andrew D.

2013-01-01

This paper examines the potential for sector-specific productivity growth, human capital, credit markets, and infrastructure to contribute to the development of stable, well-paid employment in rural areas of low-income countries. Particular emphasis is placed on the way that different sectors of the rural economy interact with each other and with local and regional product markets. A simple theoretical framework and descriptive analysis of panel data from India suggests that more emphasis should be placed on increasing the production of goods that incorporate local agricultural products as inputs. PMID:25883938

Structural Stability of a Stiffened Aluminum Fuselage Panel Subjected to Combined Mechanical and Internal Pressure Loads

NASA Technical Reports Server (NTRS)

Rouse, Marshall; Young, Richard D.; Gehrki, Ralph R.

2003-01-01

Results from an experimental and analytical study of a curved stiffened aluminum panel subjected to combined mechanical and internal pressure loads are presented. The panel loading conditions were simulated using a D-box test fixture. Analytical buckling load results calculated from a finite element analysis are presented and compared to experimental results. Buckling results presented indicate that the buckling load of the fuselage panel is significantly influenced by internal pressure loading. The experimental results suggest that the stress distribution is uniform in the panel prior to buckling. Nonlinear finite element analysis results correlates well with experimental results up to buckling.

Virtual sensors for active noise control in acoustic-structural coupled enclosures using structural sensing: part II--Optimization of structural sensor placement.

PubMed

Halim, Dunant; Cheng, Li; Su, Zhongqing

2011-04-01

The work proposed an optimization approach for structural sensor placement to improve the performance of vibro-acoustic virtual sensor for active noise control applications. The vibro-acoustic virtual sensor was designed to estimate the interior sound pressure of an acoustic-structural coupled enclosure using structural sensors. A spectral-spatial performance metric was proposed, which was used to quantify the averaged structural sensor output energy of a vibro-acoustic system excited by a spatially varying point source. It was shown that (i) the overall virtual sensing error energy was contributed additively by the modal virtual sensing error and the measurement noise energy; (ii) each of the modal virtual sensing error system was contributed by both the modal observability levels for the structural sensing and the target acoustic virtual sensing; and further (iii) the strength of each modal observability level was influenced by the modal coupling and resonance frequencies of the associated uncoupled structural/cavity modes. An optimal design of structural sensor placement was proposed to achieve sufficiently high modal observability levels for certain important panel- and cavity-controlled modes. Numerical analysis on a panel-cavity system demonstrated the importance of structural sensor placement on virtual sensing and active noise control performance, particularly for cavity-controlled modes.

Human Factors and the International Space Station

NASA Technical Reports Server (NTRS)

Peacock, Brian; Rajulu, Sudhakar; Novak, Jennifer; Rathjen, Thomas; Whitmore, Mihriban; Maida, James; Woolford, Barbara

2001-01-01

The purposes of this panel are to inform the human factors community regarding the challenges of designing the International Space Station (ISS) and to stimulate the broader human factors community into participating in the various basic and applied research opportunities associated with the ISS. This panel describes the variety of techniques used to plan and evaluate human factors for living and working in space. The panel members have contributed to many different aspects of the ISS design and operations. Architecture, equipment, and human physical performance requirements for various tasks have all been tailored to the requirements of operating in microgravity.

JANNAF Rocket Nozzle Technology Subcommittee Executive Committee Report

NASA Technical Reports Server (NTRS)

Lawrence, Timothy W.; Munafo, Paul M. (Technical Monitor)

2002-01-01

This viewgraph presentation provides information on the structure and activities of the panels of the Joint Army Navy NASA Air Force (JANNAF) Rocket Nozzle Technology Subcommittee. The panels profiled are the Processing Science and Materials Panel, the Nozzle Design, Test, and Evaluation Panel, the Nozzle Analysis and Modeling Panel, and the Nozzle Control Systems Panel. The presentation also lists meetings, workshops, and publications in which the subcommittee participated during the reporting period.

Loading tests of a wing structure for a hypersonic aircraft

NASA Technical Reports Server (NTRS)

Fields, R. A.; Reardon, L. F.; Siegel, W. H.

1980-01-01

Room-temperature loading tests were conducted on a wing structure designed with a beaded panel concept for a Mach 8 hypersonic research airplane. Strain, stress, and deflection data were compared with the results of three finite-element structural analysis computer programs and with design data. The test program data were used to evaluate the structural concept and the methods of analysis used in the design. A force stiffness technique was utilized in conjunction with load conditions which produced various combinations of panel shear and compression loading to determine the failure envelope of the buckling critical beaded panels The force-stiffness data did not result in any predictions of buckling failure. It was, therefore, concluded that the panels were conservatively designed as a result of design constraints and assumptions of panel eccentricities. The analysis programs calculated strains and stresses competently. Comparisons between calculated and measured structural deflections showed good agreement. The test program offered a positive demonstration of the beaded panel concept subjected to room-temperature load conditions.

Fabrication and evaluation of superplastically formed/weld-brazed corrugated compression panels with beaded webs

NASA Technical Reports Server (NTRS)

Royster, D. M.; Davis, R. C.; Shinn, J. M., Jr.; Bales, T. T.; Wiant, H. R.

1985-01-01

A study was made to investigate the feasibility of superplastically forming corrugated panels with beaded webs and to demonstrate the structural integrity of these panels by testing. The test panels in the study consist of superplastically formed titanium alloy Ti-6Al-4V half-hat elements that are joined by weld-brazing to titanium alloy Ti-6Al-4V caps to form either single-corrugation compression panels or multiple-corrugation compression panels. Stretching and subsequent thinning of the titanium sheet during superplastic forming is reduced by approximately 35 percent with a shallow half-hat die concept instead of a deep die concept and results in a more uniform thickness across the beaded webs. The complete panels are tested in end compression at room temperature and the results compared with analysis. The heavily loaded panels failed at loads approaching the yield strength of the titanium material. At maximum load, the caps wrinkled locally accompanied with separation of the weld-braze joint in the wrinkle. None of the panels tested, however, failed catastrophically in the weld-braze joint. Experimental test results are in good agreement with structural analysis of the panels.

Variable Stiffness Panel Structural Analyses With Material Nonlinearity and Correlation With Tests

NASA Technical Reports Server (NTRS)

Wu, K. Chauncey; Gurdal, Zafer

2006-01-01

Results from structural analyses of three tow-placed AS4/977-3 composite panels with both geometric and material nonlinearities are presented. Two of the panels have variable stiffness layups where the fiber orientation angle varies as a continuous function of location on the panel planform. One variable stiffness panel has overlapping tow bands of varying thickness, while the other has a theoretically uniform thickness. The third panel has a conventional uniform-thickness [plus or minus 45](sub 5s) layup with straight fibers, providing a baseline for comparing the performance of the variable stiffness panels. Parametric finite element analyses including nonlinear material shear are first compared with material characterization test results for two orthotropic layups. This nonlinear material model is incorporated into structural analysis models of the variable stiffness and baseline panels with applied end shortenings. Measured geometric imperfections and mechanical prestresses, generated by forcing the variable stiffness panels from their cured anticlastic shapes into their flatter test configurations, are also modeled. Results of these structural analyses are then compared to the measured panel structural response. Good correlation is observed between the analysis results and displacement test data throughout deep postbuckling up to global failure, suggesting that nonlinear material behavior is an important component of the actual panel structural response.

Engineering and Safety Partnership Enhances Safety of the Space Shuttle Program (SSP)

NASA Technical Reports Server (NTRS)

Duarte, Alberto

2007-01-01

Project Management must use the risk assessment documents (RADs) as tools to support their decision making process. Therefore, these documents have to be initiated, developed, and evolved parallel to the life of the project. Technical preparation and safety compliance of these documents require a great deal of resources. Updating these documents after-the-fact not only requires substantial increase in resources - Project Cost -, but this task is also not useful and perhaps an unnecessary expense. Hazard Reports (HRs), Failure Modes and Effects Analysis (FMEAs), Critical Item Lists (CILs), Risk Management process are, among others, within this category. A positive action resulting from a strong partnership between interested parties is one way to get these documents and related processes and requirements, released and updated in useful time. The Space Shuttle Program (SSP) at the Marshall Space Flight Center has implemented a process which is having positive results and gaining acceptance within the Agency. A hybrid Panel, with equal interest and responsibilities for the two larger organizations, Safety and Engineering, is the focal point of this process. Called the Marshall Safety and Engineering Review Panel (MSERP), its charter (Space Shuttle Program Directive 110 F, April 15, 2005), and its Operating Control Plan emphasizes the technical and safety responsibilities over the program risk documents: HRs; FMEA/CILs; Engineering Changes; anomalies/problem resolutions and corrective action implementations, and trend analysis. The MSERP has undertaken its responsibilities with objectivity, assertiveness, dedication, has operated with focus, and has shown significant results and promising perspectives. The MSERP has been deeply involved in propulsion systems and integration, real time technical issues and other relevant reviews, since its conception. These activities have transformed the propulsion MSERP in a truly participative and value added panel, making a difference for the safety of the Space Shuttle Vehicle, its crew, and personnel. Because of the MSERP's valuable contribution to the assessment of safety risk for the SSP, this paper also proposes an enhanced Panel concept that takes this successful partnership concept to a higher level of 'true partnership'. The proposed panel is aimed to be responsible for the review and assessment of all risk relative to Safety for new and future aerospace and related programs.

Composite transport wing technology development

NASA Technical Reports Server (NTRS)

Madan, Ram C.

1988-01-01

The design, fabrication, testing, and analysis of stiffened wing cover panels to assess damage tolerance criteria are discussed. The damage tolerance improvements were demonstrated in a test program using full-sized cover panel subcomponents. The panels utilized a hard skin concept with identical laminates of 44-percent 0-degree, 44-percent plus or minus 45-degree, and 12-percent 90-degree plies in the skins and stiffeners. The panel skins were impacted at midbay between the stiffeners, directly over the stiffener, and over the stiffener flange edge. The stiffener blades were impacted laterally. Impact energy levels of 100 ft-lb and 200 ft-lb were used. NASTRAN finite-element analyses were performed to simulate the nonvisible damage that was detected in the panels by nondestructive inspection. A closed-form solution for generalized loading was developed to evaluate the peel stresses in the bonded structure. Two-dimensional delamination growth analysis was developed using the principle of minimum potential energy in terms of closed-form solution for critical strain. An analysis was conducted to determine the residual compressive stress in the panels after impact damage, and the analytical predictions were verified by compression testing of the damaged panels.

Substantiation Data for Advanced Beaded and Tubular Structural Panels. Volume 3: Testing

NASA Technical Reports Server (NTRS)

Hedges, P. C.; Greene, B. E.

1974-01-01

The test program is described, which was conducted to provide the necessary experimental data to verify the design and analysis methods developed for beaded and tubular panels. Test results are summarized and presented for all local buckling and full size panel tests. Selected representative test data from each of these tests is presented in detail. The results of this program established a valid analysis and design procedure for circular tube panels. Test results from three other configurations show deformational modes which are not adequately accounted for in the present analyses.

Modal Analysis of MARS Solar Panel and Planar Vibrations

NASA Technical Reports Server (NTRS)

Simonyan, Andranik; Williams, R. Brett

2007-01-01

This slide presentation reviews the modal analysis of MARS solar panels and the planar vibrations. Included are views of the solar panels mock-up assembly, a view of the test seup,a view of the plot from the test, with the raw numbers of the frequencies in Hz values with the mode number, the spatial acceleration plots of Center sub panel at resonant frequencies, predictions from the Finite element models, an explanation of the two test that were done on the plate and the results from both tests,

Application of Interface Technology in Progressive Failure Analysis of Composite Panels

NASA Technical Reports Server (NTRS)

Sleight, D. W.; Lotts, C. G.

2002-01-01

A progressive failure analysis capability using interface technology is presented. The capability has been implemented in the COMET-AR finite element analysis code developed at the NASA Langley Research Center and is demonstrated on composite panels. The composite panels are analyzed for damage initiation and propagation from initial loading to final failure using a progressive failure analysis capability that includes both geometric and material nonlinearities. Progressive failure analyses are performed on conventional models and interface technology models of the composite panels. Analytical results and the computational effort of the analyses are compared for the conventional models and interface technology models. The analytical results predicted with the interface technology models are in good correlation with the analytical results using the conventional models, while significantly reducing the computational effort.

Biometrics Analysis and Evaluation on Korean Makgeolli Using Brainwaves and Taste Biological Sensor System

PubMed Central

Kim, Yong-Sung; Kim, Yong-Suk

2015-01-01

There are several methods available in measuring food taste. The sensory evaluation, for instance, is a typical method for panels to test of taste and recognize smell with their nose by measuring the degree of taste characteristic, intensity, and pleasure. There are many issues entailed in the traditional sensory evaluation method such as forming a panel and evaluation cost; moreover, it is only localized in particular areas. Accordingly, this paper aimed to select food in one particular area, and compare and review the content between sensory evaluations using a taste biological sensor, as well as presenting an analysis of brainwaves using EEG and finally a proposal of a new method for sensory evaluation. In this paper, the researchers have conducted a sensory evaluation whereas a maximum of nine points were accumulated by purchasing eight types of rice wine. These eight types of Makgeolli were generalized by generating multidimensional data with the use of TS-5000z, thus learning mapping points and scaling them. The contribution of this paper, therefore, is to overcome the disadvantages of the sensory evaluation with the usage of the suggested taste biological sensor system. PMID:26247031

Structural analysis and sizing of stiffened, metal matrix composite panels for hypersonic vehicles

NASA Technical Reports Server (NTRS)

Collier, Craig S.

1992-01-01

The present method for strength and stability analyses of stiffened, fiber-reinforced composite panels to be used in hypersonic vehicle structures is of great generality, and can be linked with planar finite-element analysis (FEA). Nonlinear temperature and load-dependent material data for each laminate are used to 'build-up' the stiffened panel's membrane, bending, and membrane-bending coupling stiffness terms, as well as thermal coefficients. The resulting, FEA-solved thermomechanical forces and moments are used to calculate strain at any location in the panel; this allows an effective ply-by-ply orthotropic strength analysis to be conducted, together with orthotropic instability checks for each laminated segment of the cross-section.

Failure Analysis of Discrete Damaged Tailored Extension-Shear-Coupled Stiffened Composite Panels

NASA Technical Reports Server (NTRS)

Baker, Donald J.

2005-01-01

The results of an analytical and experimental investigation of the failure of composite is tiffener panels with extension-shear coupling are presented. This tailored concept, when used in the cover skins of a tiltrotor aircraft wing has the potential for increasing the aeroelastic stability margins and improving the aircraft productivity. The extension-shear coupling is achieved by using unbalanced 45 plies in the skin. The failure analysis of two tailored panel configurations that have the center stringer and adjacent skin severed is presented. Finite element analysis of the damaged panels was conducted using STAGS (STructural Analysis of General Shells) general purpose finite element program that includes a progressive failure capability for laminated composite structures that is based on point-stress analysis, traditional failure criteria, and ply discounting for material degradation. The progressive failure predicted the path of the failure and maximum load capability. There is less than 12 percent difference between the predicted failure load and experimental failure load. There is a good match of the panel stiffness and strength between the progressive failure analysis and the experimental results. The results indicate that the tailored concept would be feasible to use in the wing skin of a tiltrotor aircraft.

Application of a trigonometric finite difference procedure to numerical analysis of compressive and shear buckling of orthotropic panels

NASA Technical Reports Server (NTRS)

Stein, M.; Housner, J. D.

1978-01-01

A numerical analysis developed for the buckling of rectangular orthotropic layered panels under combined shear and compression is described. This analysis uses a central finite difference procedure based on trigonometric functions instead of using the conventional finite differences which are based on polynomial functions. Inasmuch as the buckle mode shape is usually trigonometric in nature, the analysis using trigonometric finite differences can be made to exhibit a much faster convergence rate than that using conventional differences. Also, the trigonometric finite difference procedure leads to difference equations having the same form as conventional finite differences; thereby allowing available conventional finite difference formulations to be converted readily to trigonometric form. For two-dimensional problems, the procedure introduces two numerical parameters into the analysis. Engineering approaches for the selection of these parameters are presented and the analysis procedure is demonstrated by application to several isotropic and orthotropic panel buckling problems. Among these problems is the shear buckling of stiffened isotropic and filamentary composite panels in which the stiffener is broken. Results indicate that a break may degrade the effect of the stiffener to the extent that the panel will not carry much more load than if the stiffener were absent.

School context, friendship ties and adolescent mental health: A multilevel analysis of the Korean Youth Panel Survey (KYPS).

PubMed

Kim, Harris Hyun-Soo

2015-11-01

Research on the social determinants of health suggests that interpersonal networks play a critical role in facilitating individual mental and physical well-being. Prior studies also indicate that ecological or contextual factors contribute to positive health outcomes. This study extends prior research by examining the factors associated with adolescent health in an Asian context. Based on the multilevel analysis of the Korean Youth Panel Survey (2006 & 2007), a longitudinal project funded by the Korean government, it investigates some of the key variables related to the mental health of Korean students. Much of previous research focuses on the functions of social capital. This study contributes to the social epidemiology literature by investigating the possible downside of network ties. Specifically, it asks whether having delinquent friends is associated with negative mental health experiences. In addition, little research has been conducted concerning the associations between adolescent health outcomes and school characteristics. This study moves in that direction by examining the relationship between mental well-being of students and a variety of school related variables (e.g., subjective attitude toward school and quality of relationship with peers and teachers). Hierarchical linear modeling shows that, among the social capital control variables, being properly integrated into the family and frequent peer interaction significantly add to mental health. At the individual (student) level only, ties to delinquent friends are negatively associated with mental health, while at both individual and contextual levels, school characteristics are positively related to adolescent subjective well-being. Copyright © 2015 Elsevier Ltd. All rights reserved.

A Spectral Analysis Approach for Acoustic Radiation from Composite Panels

NASA Technical Reports Server (NTRS)

Turner, Travis L.; Singh, Mahendra P.; Mei, Chuh

2004-01-01

A method is developed to predict the vibration response of a composite panel and the resulting far-field acoustic radiation due to acoustic excitation. The acoustic excitation is assumed to consist of obliquely incident plane waves. The panel is modeled by a finite element analysis and the radiated field is predicted using Rayleigh's integral. The approach can easily include other effects such as shape memory alloy (SMA) ber reinforcement, large detection thermal postbuckling, and non-symmetric SMA distribution or lamination. Transmission loss predictions for the case of an aluminum panel excited by a harmonic acoustic pressure are shown to compare very well with a classical analysis. Results for a composite panel with and without shape memory alloy reinforcement are also presented. The preliminary results demonstrate that the transmission loss can be significantly increased with shape memory alloy reinforcement. The mechanisms for further transmission loss improvement are identified and discussed.

Shear buckling analysis of a hat-stiffened panel

NASA Technical Reports Server (NTRS)

Ko, William L.; Jackson, Raymond H.

1994-01-01

A buckling analysis was performed on a hat-stiffened panel subjected to shear loading. Both local buckling and global buckling were analyzed. The global shear buckling load was found to be several times higher than the local shear buckling load. The classical shear buckling theory for a flat plate was found to be useful in predicting the local shear buckling load of the hat-stiffened panel, and the predicted local shear buckling loads thus obtained compare favorably with the results of finite element analysis.

Reducing unmet need and unwanted childbearing: evidence from a panel survey in Pakistan.

PubMed

Jain, Anrudh K; Mahmood, Arshad; Sathar, Zeba A; Masood, Irfan

2014-06-01

Pakistan's high unmet need for contraception and low contraceptive prevalence remain a challenge, especially in light of the country's expected contribution to the FP2020 goal of expanding family planning services to an additional 120 million women with unmet need. Analysis of panel data from 14 Pakistani districts suggests that efforts to reduce unmet need should also focus on empowering women who are currently practicing contraception to achieve their own reproductive intentions through continuation of contraceptive use of any method. Providing women with better quality of care and encouraging method switching would bridge the gap that exists when women are between methods and thus would reduce unwanted births. This finding is generalizable to other countries that, like Pakistan, are highly dependent on short-acting modern and traditional methods. The approach of preventing attrition among current contraceptive users would be at least as effective as persuading nonusers to adopt a method for the first time. © 2013 The Population Council, Inc.

Improving Cancer-Related Outcomes with Connected Health - Acknowledgements

Cancer.gov

The President’s Cancer Panel is grateful to all participants who invested their time to take part in the series of workshops on connected health and cancer. A complete list of participants is in Series Information. The Panel is especially appreciative to the series co-chairs who graciously contributed their time and knowledge on this topic, providing valuable guidance during workshop planning and extensive input on this report.

Design, Optimization, and Evaluation of Integrally-Stiffened Al-2139 Panel with Curved Stiffeners

NASA Technical Reports Server (NTRS)

Havens, David; Shiyekar, Sandeep; Norris, Ashley; Bird, R. Keith; Kapania, Rakesh K.; Olliffe, Robert

2011-01-01

A curvilinear stiffened panel was designed, manufactured, and tested in the Combined Load Test Fixture at NASA Langley Research Center. The panel is representative of a large wing engine pylon rib and was optimized for minimum mass subjected to three combined load cases. The optimization included constraints on web buckling, material yielding, crippling or local stiffener failure, and damage tolerance using a new analysis tool named EBF3PanelOpt. Testing was performed for the critical combined compression-shear loading configuration. The panel was loaded beyond initial buckling, and strains and out-of-plane displacements were extracted from a total of 20 strain gages and 6 linear variable displacement transducers. The VIC-3D system was utilized to obtain full field displacements/strains in the stiffened side of the panel. The experimental data were compared with the strains and out-of-plane deflections from a high fidelity nonlinear finite element analysis. The experimental data were also compared with linear elastic finite element results of the panel/test-fixture assembly. Overall, the panel buckled very near to the predicted load in the web regions.

Thermal and Mechanical Buckling Analysis of Hypersonic Aircraft Hat-Stiffened Panels With Varying Face Sheet Geometry and Fiber Orientation

NASA Technical Reports Server (NTRS)

Ko, William L.

1996-01-01

Mechanical and thermal buckling behavior of monolithic and metal-matrix composite hat-stiffened panels were investigated. The panels have three types of face-sheet geometry: Flat face sheet, microdented face sheet, and microbulged face sheet. The metal-matrix composite panels have three types of face-sheet layups, each of which is combined with various types of hat composite layups. Finite-element method was used in the eigenvalue extractions for both mechanical and thermal buckling. The thermal buckling analysis required both eigenvalue and material property iterations. Graphical methods of the dual iterations are shown. The mechanical and thermal buckling strengths of the hat-stiffened panels with different face-sheet geometry are compared. It was found that by just microdenting or microbulging of the face sheet, the axial, shear, and thermal buckling strengths of both types of hat-stiffened panels could be enhanced considerably. This effect is more conspicuous for the monolithic panels. For the metal-matrix composite panels, the effect of fiber orientations on the panel buckling strengths was investigated in great detail, and various composite layup combinations offering, high panel buckling strengths are presented. The axial buckling strength of the metal-matrix panel was sensitive to the change of hat fiber orientation. However, the lateral, shear, and thermal buckling strengths were insensitive to the change of hat fiber orientation.

Evaluation of Thin Kevlar-Epoxy Fabric Panels Subjected to Shear Loading

NASA Technical Reports Server (NTRS)

Baker, Donald J.

1996-01-01

The results of an analytical and experimental investigation of 4-ply Kevlar-49-epoxy panels loaded by in-plane shear are presented. Approximately one-half of the panels are thin-core sandwich panels and the other panels are solid-laminate panels. Selected panels were impacted with an aluminum sphere at a velocity of either 150 or 220 ft/sec. The strength of panels impacted at 150 ft/sec was not reduced when compared to the strength of the undamaged panels, but the strength of panels impacted at 220 ft/sec was reduced by 27 to 40 percent. Results are presented for panels that were cyclically loaded from a load less than the buckling load to a load in the postbuckling load range. The thin-core sandwich panels had a lower fatigue life than the solid panels. The residual strength of the solid and sandwich panels cycled more than one million cycles exceeded the baseline undamaged panel strengths. The effect of hysteresis in the response of the sandwich panels is not significant. Results of a nonlinear finite element analysis conducted for each panel design are presented.

Electromagnetic Fields Exposure Limits

DTIC Science & Technology

2018-01-01

analysis, synthesis, integration and validation of knowledge derived through the scientific method. In NATO, S&T is addressed using different...Panel • NMSG NATO Modelling and Simulation Group • SAS System Analysis and Studies Panel • SCI Systems Concepts and Integration Panel • SET... integrity or morphology. They later also failed to find a lack of direct DNA damage in human blood (strand breaks, alkali-labile sites, and incomplete

National Renewable Energy Policy in a Global World

NASA Astrophysics Data System (ADS)

Jeong, Minji

Increasing trade of renewable energy products has significantly contributed to reducing the costs of renewable energy sources, but at the same time, it has generated protectionist policies, which may negatively affect the trend of the cost reduction. Although a few recent studies examined the rise of renewable energy protectionism and trade disputes, they are limited in addressing the conflict between the original goal of traditional renewable energy policies and the new protectionist policies under the globalized renewable energy industry. To fill this gap, this dissertation explores how the globalized renewable energy industry has changed national renewable energy policies. Through three analyses, three aspects of the globalized renewable energy industry are examined: the rise of multinational corporations, international interactions among actors, and the changes of the global and domestic market conditions. First analysis investigates how multinational renewable energy corporations have affected national policies. A content analysis of the annual reports of 15 solar photovoltaic multinational corporation shows that solar multinationals have been influenced by national policies and have adapted to the changes rather than having attempted to change national policies. Second analysis examines how diverse actors have framed renewable energy trade issues through a network analysis of the Chinese solar panel issue in the United States. The result shows that the Chinese solar panel issue was framed differently from the traditional environmental frame of renewable energy, being dominated by multinational corporations headquartered in other countries. Third analysis explores what has caused the increasing diversity in national renewable energy policies through the case studies of the U.S. and South Korea. The result reveals that the globalization of solar industry has affected the diversification of solar policies in two countries by generating both challenges, which needed to be addressed by new and additional policies, and opportunities, which strengthened the political power of domestic solar industries. The three analyses show that the globalized renewable energy industry has led to the diversification of national renewable energy policies by increasing international interactions between actors and by introducing both challenges and opportunities to domestic renewable energy industries. This research contributes to the literature on trade and the environment by analyzing a new pattern of the conflicts between traditional environmental policies and "green" protectionist policies. It also contributes to the literature on protectionism by adding an empirical case of green protectionism, one of the forms of "murky" protectionism that has risen after the global financial crisis.

Bayesian characterization of micro-perforated panels and multi-layer absorbers

NASA Astrophysics Data System (ADS)

Schmitt, Andrew Alexander Joseph

First described by the late acoustician Dah-You Maa, micro-perforated panel (MPP) absorbers produce extremely high acoustic absorption coefficients. This is done without the use of conventional fibrous or porous materials that are often used in acoustic treatments, meaning MPP absorbers are capable of being implemented and withstanding critical situations where traditional absorbers do not suffice. The absorption function of a micro-perforated panel yields high yet relatively narrow results at certain frequencies, although wide-band absorption can be designed by stacking multiple MPP absorbers comprised of different characteristic parameters. Using Bayesian analysis, the physical properties of panel thickness, pore diameter, perforation ratio, and air depth are estimated inversely from experimental data of acoustic absorption, based on theoretical models for design of micro-perforated panels. Furthermore, this analysis helps to understand the interdependence and uncertainties of the parameters and how each affects the performance of the panel. Various micro-perforated panels are manufactured and tested in single- and double-layer absorber constructions.

Validation of Methods to Predict Vibration of a Panel in the Near Field of a Hot Supersonic Rocket Plume

NASA Technical Reports Server (NTRS)

Bremner, P. G.; Blelloch, P. A.; Hutchings, A.; Shah, P.; Streett, C. L.; Larsen, C. E.

2011-01-01

This paper describes the measurement and analysis of surface fluctuating pressure level (FPL) data and vibration data from a plume impingement aero-acoustic and vibration (PIAAV) test to validate NASA s physics-based modeling methods for prediction of panel vibration in the near field of a hot supersonic rocket plume. For this test - reported more fully in a companion paper by Osterholt & Knox at 26th Aerospace Testing Seminar, 2011 - the flexible panel was located 2.4 nozzle diameters from the plume centerline and 4.3 nozzle diameters downstream from the nozzle exit. The FPL loading is analyzed in terms of its auto spectrum, its cross spectrum, its spatial correlation parameters and its statistical properties. The panel vibration data is used to estimate the in-situ damping under plume FPL loading conditions and to validate both finite element analysis (FEA) and statistical energy analysis (SEA) methods for prediction of panel response. An assessment is also made of the effects of non-linearity in the panel elasticity.

Selection and Validation of a Multilocus Variable-Number Tandem-Repeat Analysis Panel for Typing Shigella spp.▿ †

PubMed Central

Gorgé, Olivier; Lopez, Stéphanie; Hilaire, Valérie; Lisanti, Olivier; Ramisse, Vincent; Vergnaud, Gilles

2008-01-01

The Shigella genus has historically been separated into four species, based on biochemical assays. The classification within each species relies on serotyping. Recently, genome sequencing and DNA assays, in particular the multilocus sequence typing (MLST) approach, greatly improved the current knowledge of the origin and phylogenetic evolution of Shigella spp. The Shigella and Escherichia genera are now considered to belong to a unique genomospecies. Multilocus variable-number tandem-repeat (VNTR) analysis (MLVA) provides valuable polymorphic markers for genotyping and performing phylogenetic analyses of highly homogeneous bacterial pathogens. Here, we assess the capability of MLVA for Shigella typing. Thirty-two potentially polymorphic VNTRs were selected by analyzing in silico five Shigella genomic sequences and subsequently evaluated. Eventually, a panel of 15 VNTRs was selected (i.e., MLVA15 analysis). MLVA15 analysis of 78 strains or genome sequences of Shigella spp. and 11 strains or genome sequences of Escherichia coli distinguished 83 genotypes. Shigella population cluster analysis gave consistent results compared to MLST. MLVA15 analysis showed capabilities for E. coli typing, providing classification among pathogenic and nonpathogenic E. coli strains included in the study. The resulting data can be queried on our genotyping webpage (http://mlva.u-psud.fr). The MLVA15 assay is rapid, highly discriminatory, and reproducible for Shigella and Escherichia strains, suggesting that it could significantly contribute to epidemiological trace-back analysis of Shigella infections and pathogenic Escherichia outbreaks. Typing was performed on strains obtained mostly from collections. Further studies should include strains of much more diverse origins, including all pathogenic E. coli types. PMID:18216214

Cross-Lagged Analysis of Interplay Between Differential Traits in Sibling Pairs: Validation and Application to Parenting Behavior and ADHD Symptomatology.

PubMed

Moscati, Arden; Verhulst, Brad; McKee, Kevin; Silberg, Judy; Eaves, Lindon

2018-01-01

Understanding the factors that contribute to behavioral traits is a complex task, and partitioning variance into latent genetic and environmental components is a useful beginning, but it should not also be the end. Many constructs are influenced by their contextual milieu, and accounting for background effects (such as gene-environment correlation) is necessary to avoid bias. This study introduces a method for examining the interplay between traits, in a longitudinal design using differential items in sibling pairs. The model is validated via simulation and power analysis, and we conclude with an application to paternal praise and ADHD symptoms in a twin sample. The model can help identify what type of genetic and environmental interplay may contribute to the dynamic relationship between traits using a cross-lagged panel framework. Overall, it presents a way to estimate and explicate the developmental interplay between a set of traits, free from many common sources of bias.

Does network topology influence systemic risk contribution? A perspective from the industry indices in Chinese stock market.

PubMed

Long, Haiming; Zhang, Ji; Tang, Nengyu

2017-01-01

This study considers the effect of an industry's network topology on its systemic risk contribution to the stock market using data from the CSI 300 two-tier industry indices from the Chinese stock market. We first measure industry's conditional-value-at-risk (CoVaR) and the systemic risk contribution (ΔCoVaR) using the fitted time-varying t-copula function. The network of the stock industry is established based on dynamic conditional correlations with the minimum spanning tree. Then, we investigate the connection characteristics and topology of the network. Finally, we utilize seemingly unrelated regression estimation (SUR) of panel data to analyze the relationship between network topology of the stock industry and the industry's systemic risk contribution. The results show that the systemic risk contribution of small-scale industries such as real estate, food and beverage, software services, and durable goods and clothing, is higher than that of large-scale industries, such as banking, insurance and energy. Industries with large betweenness centrality, closeness centrality, and clustering coefficient and small node occupancy layer are associated with greater systemic risk contribution. In addition, further analysis using a threshold model confirms that the results are robust.

Buckling analysis and test correlation of hat stiffened panels for hypersonic vehicles

NASA Technical Reports Server (NTRS)

Percy, Wendy C.; Fields, Roger A.

1990-01-01

The paper discusses the design, analysis, and test of hat stiffened panels subjected to a variety of thermal and mechanical load conditions. The panels were designed using data from structural optimization computer codes and finite element analysis. Test methods included the grid shadow moire method and a single gage force stiffness method. The agreement between the test data and analysis provides confidence in the methods that are currently being used to design structures for hypersonic vehicles. The agreement also indicates that post buckled strength may potentially be used to reduce the vehicle weight.

Sensory analysis of lipstick.

PubMed

Yap, K C S; Aminah, A

2011-06-01

Sensory analysis of lipstick product by trained panellists started with recruiting female panels who are lipstick users, in good health condition and willing to be a part of sensory members. This group of people was further scrutinized with duo-trio method using commercial lipstick samples that are commonly used among them. About 40% of the 15 panels recruited were unable to differentiate the lipstick samples they usually use better than chance. The balance of nine panels that were corrected at least with 65% across all trials in panels screening process was formed a working group to develop sensory languages as a means of describing product similarities and differences and a scoring system. Five sessions with each session took about 90 min were carried out using 10 types of lipsticks with different waxes mixture ratio in the formulation together with six commercial lipsticks that are the most common to the panels. First session was focus on listing out the panels' perception towards the characteristic of the lipstick samples after normal application on their lips. Second session was focus on the refining and categorizing the responses gathered from the first session and translated into sensory attributes with its definition. Third session was focus on the scoring system. Fourth and fifth sessions were repetition of the third session to ensure consistency. In a collective effort of the panels, sensory attributes developed for lipstick were Spreadability, Off flavour, Hardness, Smoothness, Moist, Not messy, Glossy and Greasy. Analysis of variance was able to provide ample evidence on gauging the panel performance. A proper panels selecting and training was able to produce a reliable and sensitive trained panel for evaluating the product based on the procedures being trained. © 2011 The Authors. ICS © 2011 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

High Strength Wood-based Sandwich Panels reinforced with fiberglass and foam

Treesearch

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2014-01-01

Mechanical analysis is presented for new high-strengthsandwich panels made from wood-based phenolic impregnated laminated paper assembled with an interlocking tri-axial ribbed core. Four different panel configurations were tested, including panels with fiberglass fabric bonded to both outside faces with self-expanding urethane foam used to fill the ribbed core. The...

Combined-load buckling behavior of metal-matrix composite sandwich panels under different thermal environments

NASA Technical Reports Server (NTRS)

Ko, William L.; Jackson, Raymond H.

1991-01-01

Combined compressive and shear buckling analysis was conducted on flat rectangular sandwich panels with the consideration of transverse shear effects of the core. The sandwich panel is fabricated with titanium honeycomb core and laminated metal matrix composite face sheets. The results show that the square panel has the highest combined load buckling strength, and that the buckling strength decreases sharply with the increases of both temperature and panel aspect ratio. The effect of layup (fiber orientation) on the buckling strength of the panels was studied in detail. The metal matrix composite sandwich panel was much more efficient than the sandwich panel with nonreinforced face sheets and had the same specific weight.

Pooled Sequencing of 531 Genes in Inflammatory Bowel Disease Identifies an Associated Rare Variant in BTNL2 and Implicates Other Immune Related Genes

PubMed Central

Prescott, Natalie J.; Lehne, Benjamin; Stone, Kristina; Lee, James C.; Taylor, Kirstin; Knight, Jo; Papouli, Efterpi; Mirza, Muddassar M.; Simpson, Michael A.; Spain, Sarah L.; Lu, Grace; Fraternali, Franca; Bumpstead, Suzannah J.; Gray, Emma; Amar, Ariella; Bye, Hannah; Green, Peter; Chung-Faye, Guy; Hayee, Bu’Hussain; Pollok, Richard; Satsangi, Jack; Parkes, Miles; Barrett, Jeffrey C.; Mansfield, John C.; Sanderson, Jeremy; Lewis, Cathryn M.; Weale, Michael E.; Schlitt, Thomas; Mathew, Christopher G.

2015-01-01

The contribution of rare coding sequence variants to genetic susceptibility in complex disorders is an important but unresolved question. Most studies thus far have investigated a limited number of genes from regions which contain common disease associated variants. Here we investigate this in inflammatory bowel disease by sequencing the exons and proximal promoters of 531 genes selected from both genome-wide association studies and pathway analysis in pooled DNA panels from 474 cases of Crohn’s disease and 480 controls. 80 variants with evidence of association in the sequencing experiment or with potential functional significance were selected for follow up genotyping in 6,507 IBD cases and 3,064 population controls. The top 5 disease associated variants were genotyped in an extension panel of 3,662 IBD cases and 3,639 controls, and tested for association in a combined analysis of 10,147 IBD cases and 7,008 controls. A rare coding variant p.G454C in the BTNL2 gene within the major histocompatibility complex was significantly associated with increased risk for IBD (p = 9.65x10−10, OR = 2.3[95% CI = 1.75–3.04]), but was independent of the known common associated CD and UC variants at this locus. Rare (<1%) and low frequency (1–5%) variants in 3 additional genes showed suggestive association (p<0.005) with either an increased risk (ARIH2 c.338-6C>T) or decreased risk (IL12B p.V298F, and NICN p.H191R) of IBD. These results provide additional insights into the involvement of the inhibition of T cell activation in the development of both sub-phenotypes of inflammatory bowel disease. We suggest that although rare coding variants may make a modest overall contribution to complex disease susceptibility, they can inform our understanding of the molecular pathways that contribute to pathogenesis. PMID:25671699

A research program to reduce interior noise in general aviation airplanes: Noise reduction through a cavity-backed flexible plate

NASA Technical Reports Server (NTRS)

Roskam, J.; Vandam, C. P. G.

1978-01-01

A prediction method is reported for noise reduction through a cavity-backed panel. The analysis takes into account only cavity modes in one direction. The results of this analysis were to find the effect of acoustic stiffness of a backing cavity on the panel behavior. The resulting changes in the noise reduction through the panel are significant.

Multidisciplinary Optimization and Damage Tolerance of Stiffened Structures

NASA Astrophysics Data System (ADS)

Jrad, Mohamed

THE structural optimization of a cantilever aircraft wing with curvilinear spars and ribs and stiffeners is described. For the optimization of a complex wing, a common strategy is to divide the optimization procedure into two subsystems: the global wing optimization which optimizes the geometry of spars, ribs and wing skins; and the local panel optimization which optimizes the design variables of local panels bordered by spars and ribs. The stiffeners are placed on the local panels to increase the stiffness and buckling resistance. During the local panel optimization, the stress information is taken from the global model as a displacement boundary condition on the panel edges using the so-called "Global-Local Approach". Particle swarm optimization is used in the integration of global/local optimization to optimize the SpaRibs. Parallel computing approach has been developed in the Python programming language to reduce the CPU time. The license cycle-check method and memory self-adjustment method are two approaches that have been applied in the parallel framework in order to optimize the use of the resources by reducing the license and memory limitations and making the code robust. The integrated global-local optimization approach has been applied to subsonic NASA common research model (CRM) wing, which proves the methodology's application scaling with medium fidelity FEM analysis. The structural weight of the wing has been reduced by 42% and the parallel implementation allowed a reduction in the CPU time by 89%. The aforementioned Global-Local Approach is investigated and applied to a composite panel with crack at its center. Because of composite laminates' heterogeneity, an accurate analysis of these requires very high time and storage space. A possible alternative to reduce the computational complexity is the global-local analysis which involves an approximate analysis of the whole structure followed by a detailed analysis of a significantly smaller region of interest. Buckling analysis of a composite panel with attached longitudinal stiffeners under compressive loads is performed using Ritz method with trigonometric functions. Results are then compared to those from Abaqus FEA for different shell elements. The case of composite panel with one, two, and three stiffeners is investigated. The effect of the distance between the stiffeners on the buckling load is also studied. The variation of the buckling load and buckling modes with the stiffeners' height is investigated. It is shown that there is an optimum value of stiffeners' height beyond which the structural response of the stiffened panel is not improved and the buckling load does not increase. Furthermore, there exist different critical values of stiffener's height at which the buckling mode of the structure changes. Next, buckling analysis of a composite panel with two straight stiffeners and a crack at the center is performed. Finally, buckling analysis of a composite panel with curvilinear stiffeners and a crack at the center is also conducted. Results show that panels with a larger crack have a reduced buckling load and that the buckling load decreases slightly when using higher order 2D shell FEM elements. A damage tolerance framework, EBF3PanelOpt, has been developed to design and analyze curvilinearly stiffened panels. The framework is written with the scripting language Python and it interacts with the commercial software MSC. Patran (for geometry and mesh creation), MSC. Nastran (for finite element analysis), and MSC. Marc (for damage tolerance analysis). The crack location is set to the location of the maximum value of the major principal stress while its orientation is set normal to the major principal axis direction. The effective stress intensity factor is calculated using the Virtual Crack Closure Technique and compared to the fracture toughness of the material in order to decide whether the crack will expand or not. The ratio of these two quantities is used as a constraint, along with the buckling factor, Kreisselmeier and Steinhauser criteria, and crippling factor. The EBF3PanelOpt framework is integrated within a two-step Particle Swarm Optimization in order to minimize the weight of the panel while satisfying the aforementioned constraints and using all the shape and thickness parameters as design variables. The result of the PSO is used then as an initial guess for the Gradient Based Optimization using only the thickness parameters as design variables and employing VisualDOC. Stiffened panel with two curvilinear stiffeners is optimized for two load cases. In both cases, significant reduction has been made for the panel's weight.

Pitting of Space Shuttle's Inconel Honeycomb Conical Seal Panel

NASA Technical Reports Server (NTRS)

Zimmerman, Frank; Gentz, Steven J.; Miller, James B.

2006-01-01

This paper describes the approach, findings, conclusions and recommendations associated with the investigation of the conical seal pitting. It documents the cause and contributing factors of the pitting, the means used to isolate each contributor, and the supporting evidence for the primary cause of the pitting. Finally, the selection, development and verification of the repair procedure used to restore the conical seal panel is described with supporting process and metallurgical rationale for selection.

Evaluation of a Compression-Loaded-Stitched-Multi-Bay Fuselage Panel With Barely Visible Impact Damage

NASA Technical Reports Server (NTRS)

Baker, Donald J.; Li, Ji-An

2005-01-01

The experimental results from a stitched VaRTM carbon-epoxy composite panel tested under uni-axial compression loading are presented along with nonlinear finite element analysis prediction of the response. The curved panel is divided by frames and stringers into six bays with a column of three bays along the compressive loading direction. The frames are supported at the frame ends to resist out-of-plane translation. Back-to-back strain gages are used to record the strain and displacement transducers were used to record the out-of-plane displacements. In addition a full-field-displacement measurement technique that utilizes a camera-based-stereo-vision system was used to record the displacements. The panel was loaded to 1.5 times the predicted initial buckling load (1st bay buckling load, P(sub er) from the nonlinear finite element analysis and then was removed from the test machine for impact testing. After impacting with 20 ft-lbs of energy using a spherical impactor to produce barely visible damage the panel was loaded in compression until failure. The buckling load of the first bay to buckle was 97% of the buckling load before impact. The stitching constrained the impact damage from growing during the loading to failure. Impact damage had very little overall effect on panel stiffness. Panel stiffness measured by the full-field-displacement technique indicated a 13% loss in stiffness after impact. The panel failed at 1.64 times the first panel buckling load. The barely visible impact damage did not grow noticeably as the panel failed by global instability due to stringer-web terminations at the frame locations. The predictions from the nonlinear analysis of the finite element modeling of the entire specimen were very effective in the capture of the initial buckling and global behavior of the panel. In addition, the prediction highlighted the weakness of the panel under compression due to stringer web terminations. Both the test results and the nonlinear predictions serve to reinforce the severe penalty in structural integrity caused by the low cost manufacturing technique to terminate the stringer webs, and demonstrates the importance of this type of sub-component testing and high fidelity failure analysis in the design of a composite fuselage.

More Trees, More Poverty? The Socioeconomic Effects of Tree Plantations in Chile, 2001-2011

NASA Astrophysics Data System (ADS)

Andersson, Krister; Lawrence, Duncan; Zavaleta, Jennifer; Guariguata, Manuel R.

2016-01-01

Tree plantations play a controversial role in many nations' efforts to balance goals for economic development, ecological conservation, and social justice. This paper seeks to contribute to this debate by analyzing the socioeconomic impact of such plantations. We focus our study on Chile, a country that has experienced extraordinary growth of industrial tree plantations. Our analysis draws on a unique dataset with longitudinal observations collected in 180 municipal territories during 2001-2011. Employing panel data regression techniques, we find that growth in plantation area is associated with higher than average rates of poverty during this period.

More Trees, More Poverty? The Socioeconomic Effects of Tree Plantations in Chile, 2001-2011.

PubMed

Andersson, Krister; Lawrence, Duncan; Zavaleta, Jennifer; Guariguata, Manuel R

2016-01-01

Tree plantations play a controversial role in many nations' efforts to balance goals for economic development, ecological conservation, and social justice. This paper seeks to contribute to this debate by analyzing the socioeconomic impact of such plantations. We focus our study on Chile, a country that has experienced extraordinary growth of industrial tree plantations. Our analysis draws on a unique dataset with longitudinal observations collected in 180 municipal territories during 2001-2011. Employing panel data regression techniques, we find that growth in plantation area is associated with higher than average rates of poverty during this period.

3D Modelling of Urban Terrain (Modelisation 3D de milieu urbain)

DTIC Science & Technology

2011-09-01

Panel • IST Information Systems Technology Panel • NMSG NATO Modelling and Simulation Group • SAS System Analysis and Studies Panel • SCI... Systems Concepts and Integration Panel • SET Sensors and Electronics Technology Panel These bodies are made up of national representatives as well as...of a part of it may be made for individual use only. The approval of the RTA Information Management Systems Branch is required for more than one

The fractal characteristic of facial anthropometric data for developing PCA fit test panels for youth born in central China.

PubMed

Yang, Lei; Wei, Ran; Shen, Henggen

2017-01-01

New principal component analysis (PCA) respirator fit test panels had been developed for current American and Chinese civilian workers based on anthropometric surveys. The PCA panels used the first two principal components (PCs) obtained from a set of 10 facial dimensions. Although the PCA panels for American and Chinese subjects adopted the bivairate framework with two PCs, the number of the PCs retained in the PCA analysis was different between Chinese subjects and Americans. For the Chinese youth group, the third PC should be retained in the PCA analysis for developing new fit test panels. In this article, an additional number label (ANL) is used to explain the third PC in PCA analysis when the first two PCs are used to construct the PCA half-facepiece respirator fit test panel for Chinese group. The three-dimensional box-counting method is proposed to estimate the ANLs by calculating fractal dimensions of the facial anthropometric data of the Chinese youth. The linear regression coefficients of scale-free range R 2 are all over 0.960, which demonstrates that the facial anthropometric data of the Chinese youth has fractal characteristic. The youth subjects born in Henan province has an ANL of 2.002, which is lower than the composite facial anthropometric data of Chinese subjects born in many provinces. Hence, Henan youth subjects have the self-similar facial anthropometric characteristic and should use the particular ANL (2.002) as the important tool along with using the PCA panel. The ANL method proposed in this article not only provides a new methodology in quantifying the characteristics of facial anthropometric dimensions for any ethnic/racial group, but also extends the scope of PCA panel studies to higher dimensions.

Discussion session on star formation, molecular clouds and the interstellar medium

NASA Technical Reports Server (NTRS)

Strom, Karen M.; Nordh, Lennart; Dwek, Eli

1994-01-01

In this panel discussion contributions were made by K. Strom, L. Nordh and H. Zinnecker on the contributions of surveys to the study of star formation regions, by B. Burton on a survey of galactic H I and by E. Dwek on the detection of galactic supernovae by infrared surveys. The contributions of K. Strom, L. Nordh and E. Dwek are summarized here.

Open-Mode Debonding Analysis of Curved Sandwich Panels Subjected to Heating and Cryogenic Cooling on Opposite Faces

NASA Technical Reports Server (NTRS)

Ko, William L.

1999-01-01

Increasing use of curved sandwich panels as aerospace structure components makes it vital to fully understand their thermostructural behavior and identify key factors affecting the open-mode debonding failure. Open-mode debonding analysis is performed on a family of curved honeycomb-core sandwich panels with different radii of curvature. The curved sandwich panels are either simply supported or clamped, and are subjected to uniform heating on the convex side and uniform cryogenic cooling on the concave side. The finite-element method was used to study the effects of panel curvature and boundary condition on the open-mode stress (radial tensile stress) and displacement fields in the curved sandwich panels. The critical stress point, where potential debonding failure could initiate, was found to be at the midspan (or outer span) of the inner bonding interface between the sandwich core and face sheet on the concave side, depending on the boundary condition and panel curvature. Open-mode stress increases with increasing panel curvature, reaching a maximum value at certain high curvature, and then decreases slightly as the panel curvature continues to increase and approach that of quarter circle. Changing the boundary condition from simply supported to clamped reduces the magnitudes of open-mode stresses and the associated sandwich core depth stretching.

Identification of the rat liver cytochrome P450 enzymes involved in the metabolism of the calcium channel blocker dipfluzine hydrochloride.

PubMed

Guo, Wei; Shi, Xiaowei; Wang, Wei; Zhang, Weili; Li, Junxia

2014-11-01

This study aimed to identify the specific cytochrome P450 (CYP450) enzymes involved in the metabolism of dipfluzine hydrochloride using the combination of a chemical inhibition study, a correlation analysis and a panel of recombinant rat CYP450 enzymes. The incubation of Dip with rat liver microsomes yielded four metabolites, which were identified by liquid chromatography-coupled tandem mass spectrometry (LC/MS/MS). The results from the assays involving eight selective inhibitors indicated that CYP3A and CYP2A1 contributed most to the metabolism of Dip, followed by CYP2C11, CYP2E1 and CYP1A2; however, CYP2B1, CYP2C6 and CYP2D1 did not contribute to the formation of the metabolites. The results of the correlation analysis and the assays involving the recombinant CYP450 enzymes further confirmed the above results and concluded that CYP3A2 contributed more than CYP3A1. The results will be valuable in understanding drug-drug interactions when Dip is coadministered with other drugs. Copyright © 2014 Elsevier B.V. All rights reserved.

Efficiency optimization of a photovoltaic water pumping system for irrigation in Ouargla, Algeria

NASA Astrophysics Data System (ADS)

Louazene, M. L.; Garcia, M. C. Alonso; Korichi, D.

2017-02-01

This work is technical study to contribute to the optimization of pumping systems powered by solar energy (clean) and used in the field of agriculture. To achieve our goals, we studied the techniques that must be entered on a photovoltaic system for maximum energy from solar panels. Our scientific contribution in this research is the realization of an efficient photovoltaic pumping system for irrigation needs. To achieve this and extract maximum power from the PV generator, two axes have been optimized: 1. Increase in the uptake of solar radiation by choice an optimum tilt angle of the solar panels, and 2. it is necessary to add an adaptation device, MPPT controller with a DC-DC converter, between the source and the load.

Titanium Honeycomb Panel Testing

NASA Technical Reports Server (NTRS)

Richards, W. Lance; Thompson, Randolph C.

1996-01-01

Thermal-mechanical tests were performed on a titanium honeycomb sandwich panel to experimentally validate the hypersonic wing panel concept and compare test data with analysis. Details of the test article, test fixture development, instrumentation, and test results are presented. After extensive testing to 900 deg. F, non-destructive evaluation of the panel has not detected any significant structural degradation caused by the applied thermal-mechanical loads.

Financial incentives for cadaver organ donation: an ethical reappraisal.

PubMed

Arnold, Robert; Bartlett, Steven; Bernat, James; Colonna, John; Dafoe, Donald; Dubler, Nancy; Gruber, Scott; Kahn, Jeffrey; Luskin, Richard; Nathan, Howard; Orloff, Susan; Prottas, Jeffrey; Shapiro, Robyn; Ricordi, Camillo; Youngner, Stuart; Delmonico, Francis L

2002-04-27

A panel of ethicists, organ procurement organization executives, physicians, and surgeons was convened by the sponsorship of the American Society of Transplant Surgeons to determine whether an ethically acceptable pilot trial could be proposed to provide a financial incentive for a family to consent to the donation of organs from a deceased relative. An ethical methodology was developed that could be applied to any proposal for monetary compensation to elucidate its ethical acceptability. An inverse relationship between financial incentives for increasing the families' consent for cadaver donation that clearly would be ethically acceptable (e.g., a contribution to a charity chosen by the family or a reimbursement for funeral expenses) and those approaches that would more likely increase the rate of donation (e.g., direct payment or tax incentive) was evident. The panel was unanimously opposed to the exchange of money for cadaver donor organs because either a direct payment or tax incentive would violate the ideal standard of altruism in organ donation and unacceptably commercialize the value of human life by commodifying donated organs. However, a majority of the panel members supported reimbursement for funeral expenses or a charitable contribution as an ethically permissible approach. The panel concluded that the concept of the organ as a gift could be sustained by a funeral reimbursement or charitable contribution that conveyed the appreciation of society to the family for their donation. Depending on the amount of reimbursement provided for funeral expenses, this approach could be ethically distinguished from a direct payment, by their intrusion into the realm of altruism and voluntariness. We suggest that a pilot project be conducted to determine whether this kind of a financial incentive would be acceptable to the public and successful in increasing organ donation.

Two-Dimensional Sequential and Concurrent Finite Element Analysis of Unstiffened and Stiffened Aluminum and Composite Panels with Hole

NASA Technical Reports Server (NTRS)

Razzaq, Zia; Prasad, Venkatesh

1988-01-01

The results of a detailed investigation of the distribution of stresses in aluminum and composite panels subjected to uniform end shortening are presented. The focus problem is a rectangular panel with two longitudinal stiffeners, and an inner stiffener discontinuous at a central hole in the panel. The influence of the stiffeners on the stresses is evaluated through a two-dimensional global finite element analysis in the absence or presence of the hole. Contrary to the physical feel, it is found that the maximum stresses from the glocal analysis for both stiffened aluminum and composite panels are greater than the corresponding stresses for the unstiffened panels. The inner discontinuous stiffener causes a greater increase in stresses than the reduction provided by the two outer stiffeners. A detailed layer-by-layer study of stresses around the hole is also presented for both unstiffened and stiffened composite panels. A parallel equation solver is used for the global system of equations since the computational time is far less than that using a sequential scheme. A parallel Choleski method with up to 16 processors is used on Flex/32 Multicomputer at NASA Langley Research Center. The parallel computing results are summarized and include the computational times, speedups, bandwidths, and their inter-relationships for the panel problems. It is found that the computational time for the Choleski method decreases with a decrease in bandwidth, and better speedups result as the bandwidth increases.

Optimal Design of Grid-Stiffened Composite Panels Using Global and Local Buckling Analysis

NASA Technical Reports Server (NTRS)

Ambur, Damodar R.; Jaunky, Navin; Knight, Norman F., Jr.

1996-01-01

A design strategy for optimal design of composite grid-stiffened panels subjected to global and local buckling constraints is developed using a discrete optimizer. An improved smeared stiffener theory is used for the global buckling analysis. Local buckling of skin segments is assessed using a Rayleigh-Ritz method that accounts for material anisotropy and transverse shear flexibility. The local buckling of stiffener segments is also assessed. Design variables are the axial and transverse stiffener spacing, stiffener height and thickness, skin laminate, and stiffening configuration. The design optimization process is adapted to identify the lightest-weight stiffening configuration and pattern for grid stiffened composite panels given the overall panel dimensions, design in-plane loads, material properties, and boundary conditions of the grid-stiffened panel.

Economic analysis of electric heating based on critical electricity price

NASA Astrophysics Data System (ADS)

Xie, Feng; Sun, Zhijie; Zhou, Xinnan; Fu, Chengran; Yang, Jie

2018-06-01

The State Grid Corporation of China proposes an alternative energy strategy, which will make electric heating an important task in the field of residential electricity consumption. This article takes this as the background, has made the detailed introduction to the inhabitant electric heating technology, and take the Zhangjiakou electric panels heating technology as an example, from the expense angle, has carried on the analysis to the electric panels heating economy. In the field of residential heating, electric panels operating costs less than gas boilers. After customers implying energy-saving behavior, electric panels operating cost is even lower than coal-fired boilers. The critical price is higher than the execution price, which indicates that the economic performance of the electric panels is significantly higher than that of the coal boiler.

Space and surface power for the space exploration initiative: Results from project outreach

NASA Technical Reports Server (NTRS)

Shipbaugh, C.; Solomon, K.; Gonzales, D.; Juncosa, M.; Bauer, T.; Salter, R.

1991-01-01

The analysis and evaluations of the Space and Surface Power panel, one of eight panels created by RAND to screen and analyze submissions to the Space Exploration Initiative (SEI) Outreach Program, is documented. In addition to managing and evaluating the responses, or submissions, to this public outreach program, RAND conducted its own analysis and evaluation relevent to SEI mission concepts, systems, and technologies. The Power panel screened and analyzed submissions for which a substantial portion of the concepts involved power generation sources, transmission, distribution, thermal management, and handling of power (including conditioning, conversion, packaging, and enhancements in system components). A background discussion of the areas the Power panel covered and the issues the reviewers considered pertinent to the analysis of power submissions are presented. An overview of each of the highest-ranked submissions and then a discussion of these submissions is presented. The results of the analysis is presented.

Full-Scale Testing and Analysis of Curved Aircraft Fuselage Panels.

DOT National Transportation Integrated Search

1993-12-01

The report presents data on (1) residual strength of aircraft panels containing Multiple-Site Damage (MSD) in lap splices, and (2) fatigue strength of panels subjected to cyclic pressure loading. The testing was conducted using the dedicated Aging Ai...

Testing and analysis of flat and curved panels with multiple cracks

DOT National Transportation Integrated Search

1994-08-01

An experimental and analytical investigation of multiple cracking in various types of test specimens is described in this paper. The testing phase is comprised of a flat unstiffened panel series and curved stiffened and unstiffened panel series. The ...

Testing and analysis of flat and curved panels with multiple cracks

NASA Technical Reports Server (NTRS)

Broek, David; Jeong, David Y.; Thomson, Douglas

1994-01-01

An experimental and analytical investigation of multiple cracking in various types of test specimens is described in this paper. The testing phase is comprised of a flat unstiffened panel series and curved stiffened and unstiffened panel series. The test specimens contained various configurations for initial damage. Static loading was applied to these specimens until ultimate failure, while loads and crack propagation were recorded. This data provides the basis for developing and validating methodologies for predicting linkup of multiple cracks, progression to failure, and overall residual strength. The results from twelve flat coupon and ten full scale curved panel tests are presented. In addition, an engineering analysis procedure was developed to predict multiple crack linkup. Reasonable agreement was found between predictions and actual test results for linkup and residual strength for both flat and curved panels. The results indicate that an engineering analysis approach has the potential to quantitatively assess the effect of multiple cracks in the arrest capability of an aircraft fuselage structure.

Compressive buckling analysis of hat-stiffened panel

NASA Technical Reports Server (NTRS)

Ko, William L.; Jackson, Raymond H.

1991-01-01

Buckling analysis was performed on a hat-stiffened panel subjected to uniaxial compression. Both local buckling and global buckling were analyzed. It was found that the global buckling load was several times higher than the buckling load. The predicted local buckling loads compared favorably with both experimental data and finite-element analysis.

The effect of oblique angle of sound incidence, realistic edge conditions, curvature and in-plane panel stresses on the noise reduction characteristics of general aviation type panels

NASA Technical Reports Server (NTRS)

Grosveld, F.; Lameris, J.; Dunn, D.

1979-01-01

Experiments and a theoretical analysis were conducted to predict the noise reduction of inclined and curved panels. These predictions are compared to the experimental results with reasonable agreement between theory and experiment for panels under an oblique angle of sound incidence. Theoretical as well as experimental results indicate a big increase in noise reduction when a flat test panel is curved. Further curving the panel slightly decreases the noise reduction. Riveted flat panels are shown to give a higher noise reduction in the stiffness-controlled frequency region, while bonded panels are superior in this region when the test panel is curved. Experimentally measured noise reduction characteristics of flat aluminum panels with uniaxial in-plane stresses are presented and discussed. These test results indicate an important improvement in the noise reduction of these panels in the frequency range below the fundamental panel/cavity frequency.

Automatic generation and analysis of solar cell IV curves

DOEpatents

Kraft, Steven M.; Jones, Jason C.

2014-06-03

A photovoltaic system includes multiple strings of solar panels and a device presenting a DC load to the strings of solar panels. Output currents of the strings of solar panels may be sensed and provided to a computer that generates current-voltage (IV) curves of the strings of solar panels. Output voltages of the string of solar panels may be sensed at the string or at the device presenting the DC load. The DC load may be varied. Output currents of the strings of solar panels responsive to the variation of the DC load are sensed to generate IV curves of the strings of solar panels. IV curves may be compared and analyzed to evaluate performance of and detect problems with a string of solar panels.

A simple formula for insertion loss prediction of large acoustical enclosures using statistical energy analysis method

NASA Astrophysics Data System (ADS)

Kim, Hyun-Sil; Kim, Jae-Seung; Lee, Seong-Hyun; Seo, Yun-Ho

2014-12-01

Insertion loss prediction of large acoustical enclosures using Statistical Energy Analysis (SEA) method is presented. The SEA model consists of three elements: sound field inside the enclosure, vibration energy of the enclosure panel, and sound field outside the enclosure. It is assumed that the space surrounding the enclosure is sufficiently large so that there is no energy flow from the outside to the wall panel or to air cavity inside the enclosure. The comparison of the predicted insertion loss to the measured data for typical large acoustical enclosures shows good agreements. It is found that if the critical frequency of the wall panel falls above the frequency region of interest, insertion loss is dominated by the sound transmission loss of the wall panel and averaged sound absorption coefficient inside the enclosure. However, if the critical frequency of the wall panel falls into the frequency region of interest, acoustic power from the sound radiation by the wall panel must be added to the acoustic power from transmission through the panel.

Test results from large wing and fuselage panels

NASA Technical Reports Server (NTRS)

Madan, Ram C.; Voldman, Mike

1993-01-01

This paper presents the first results in an assessment of the strength, stiffness, and damage tolerance of stiffened wing and fuselage subcomponents. Under this NASA funded program, 10 large wing and fuselage panels, variously fabricated by automated tow placement and dry-stitched preform/resin transfer molding, are to be tested. The first test of an automated tow placement six-longeron fuselage panel under shear load was completed successfully. Using NASTRAN finite-element analysis the stiffness of the panel in the linear range prior to buckling was predicted within 3.5 percent. A nonlinear analysis predicted the buckling load within 10 percent and final failure load within 6 percent. The first test of a resin transfer molding six-stringer wing panel under compression was also completed. The panel failed unexpectedly in buckling because of inadequate supporting structure. The average strain was 0.43 percent with a line load of 20.3 kips per inch of width. This strain still exceeds the design allowable strains. Also, the stringers did not debond before failure, which is in contrast to the general behavior of unstitched panels.

The relationship between air pollution, fossil fuel energy consumption, and water resources in the panel of selected Asia-Pacific countries.

PubMed

Rafindadi, Abdulkadir Abdulrashid; Yusof, Zarinah; Zaman, Khalid; Kyophilavong, Phouphet; Akhmat, Ghulam

2014-10-01

The objective of the study is to examine the relationship between air pollution, fossil fuel energy consumption, water resources, and natural resource rents in the panel of selected Asia-Pacific countries, over a period of 1975-2012. The study includes number of variables in the model for robust analysis. The results of cross-sectional analysis show that there is a significant relationship between air pollution, energy consumption, and water productivity in the individual countries of Asia-Pacific. However, the results of each country vary according to the time invariant shocks. For this purpose, the study employed the panel least square technique which includes the panel least square regression, panel fixed effect regression, and panel two-stage least square regression. In general, all the panel tests indicate that there is a significant and positive relationship between air pollution, energy consumption, and water resources in the region. The fossil fuel energy consumption has a major dominating impact on the changes in the air pollution in the region.

Analysis of Composite Panels Subjected to Thermo-Mechanical Loads

NASA Technical Reports Server (NTRS)

Noor, Ahmed K.; Peters, Jeanne M.

1999-01-01

The results of a detailed study of the effect of cutout on the nonlinear response of curved unstiffened panels are presented. The panels are subjected to combined temperature gradient through-the-thickness combined with pressure loading and edge shortening or edge shear. The analysis is based on a first-order, shear deformation, Sanders-Budiansky-type shell theory with the effects of large displacements, moderate rotations, transverse shear deformation, and laminated anisotropic material behavior included. A mixed formulation is used with the fundamental unknowns consisting of the generalized displacements and the stress resultants of the panel. The nonlinear displacements, strain energy, principal strains, transverse shear stresses, transverse shear strain energy density, and their hierarchical sensitivity coefficients are evaluated. The hierarchical sensitivity coefficients measure the sensitivity of the nonlinear response to variations in the panel parameters, as well as in the material properties of the individual layers. Numerical results are presented for cylindrical panels and show the effects of variations in the loading and the size of the cutout on the global and local response quantities as well as their sensitivity to changes in the various panel, layer, and micromechanical parameters.

Detailed analysis and test correlation of a stiffened composite wing panel

NASA Technical Reports Server (NTRS)

Davis, D. Dale, Jr.

1991-01-01

Nonlinear finite element analysis techniques are evaluated by applying them to a realistic aircraft structural component. A wing panel from the V-22 tiltrotor aircraft is chosen because it is a typical modern aircraft structural component for which there is experimental data for comparison of results. From blueprints and drawings supplied by the Bell Helicopter Textron Corporation, a very detailed finite element model containing 2284 9-node Assumed Natural-Coordinate Strain (ANS) elements was generated. A novel solution strategy which accounts for geometric nonlinearity through the use of corotating element reference frames and nonlinear strain displacements relations is used to analyze this detailed model. Results from linear analyses using the same finite element model are presented in order to illustrate the advantages and costs of the nonlinear analysis as compared with the more traditional linear analysis. Strain predictions from both the linear and nonlinear stress analyses are shown to compare well with experimental data up through the Design Ultimate Load (DUL) of the panel. However, due to the extreme nonlinear response of the panel, the linear analysis was not accurate at loads above the DUL. The nonlinear analysis more accurately predicted the strain at high values of applied load, and even predicted complicated nonlinear response characteristics, such as load reversals, at the observed failure load of the test panel. In order to understand the failure mechanism of the panel, buckling and first ply failure analyses were performed. The buckling load was 17 percent above the observed failure load while first ply failure analyses indicated significant material damage at and below the observed failure load.

Summary of the SWOT panel's evaluation of the organisation and financing of the Danish health care system.

PubMed

Christiansen, Terkel

2002-02-01

The organisation and financing of the Danish health care system was evaluated within a framework of a SWOT analysis (analysis of strengths, weaknesses, opportunities and threats) by a panel of five members with a background in health economics. This paper systematically summarises the panel's assessments, within the framework of the triangular model of health care. The members of the panel are in agreement on a number of aspects, while their views on other aspects differ. In general they find many strength in the way the system is organised and financed more so in the primary sector than in the hospital sector.

Uncertainties in predicting solar panel power output

NASA Technical Reports Server (NTRS)

Anspaugh, B.

1974-01-01

The problem of calculating solar panel power output at launch and during a space mission is considered. The major sources of uncertainty and error in predicting the post launch electrical performance of the panel are considered. A general discussion of error analysis is given. Examples of uncertainty calculations are included. A general method of calculating the effect on the panel of various degrading environments is presented, with references supplied for specific methods. A technique for sizing a solar panel for a required mission power profile is developed.

Solar radiation - to - power generation models for one-axis tracking PV system with on-site measurements from Eskisehir, Turkey

NASA Astrophysics Data System (ADS)

Filik, Tansu; Başaran Filik, Ümmühan; Nezih Gerek, Ömer

2017-11-01

In this study, new analytic models are proposed for mapping on-site global solar radiation values to electrical power output values in solar photovoltaic (PV) panels. The model extraction is achieved by simultaneously recording solar radiation and generated power from fixed and tracking panels, each with capacity of 3 kW, in Eskisehir (Turkey) region. It is shown that the relation between the solar radiation and the corresponding electric power is not only nonlinear, but it also exhibits an interesting time-varying characteristic in the form of a hysteresis function. This observed radiation-to-power relation is, then, analytically modelled with three piece-wise function parts (corresponding to morning, noon and evening times), which is another novel contribution of this work. The model is determined for both fixed panels and panels with a tracking system. Especially the panel system with a dynamic tracker produces a harmonically richer (with higher values in general) characteristic, so higher order polynomial models are necessary for the construction of analytical solar radiation models. The presented models, characteristics of the hysteresis functions, and differences in the fixed versus solar-tracking panels are expected to provide valuable insight for further model based researches.

Sound Transmission Loss Through a Corrugated-Core Sandwich Panel with Integrated Acoustic Resonators

NASA Technical Reports Server (NTRS)

Schiller, Noah H.; Allen, Albert R.; Zalewski, Bart F; Beck, Benjamin S.

2014-01-01

The goal of this study is to better understand the effect of structurally integrated resonators on the transmission loss of a sandwich panel. The sandwich panel has facesheets over a corrugated core, which creates long aligned chambers that run parallel to the facesheets. When ports are introduced through the facesheet, the long chambers within the core can be used as low-frequency acoustic resonators. By integrating the resonators within the structure they contribute to the static load bearing capability of the panel while also attenuating noise. An analytical model of a panel with embedded resonators is derived and compared with numerical simulations. Predictions show that acoustic resonators can significantly improve the transmission loss of the sandwich panel around the natural frequency of the resonators. In one configuration with 0.813 m long internal chambers, the diffuse field transmission loss is improved by more than 22 dB around 104 Hz. The benefit is achieved with no added mass or volume relative to the baseline structure. The embedded resonators are effective because they radiate sound out-of-phase with the structure. This results in destructive interference, which leads to less transmitted sound power.

Forecasting obesity prevalence in Korean adults for the years 2020 and 2030 by the analysis of contributing factors.

PubMed

Baik, Inkyung

2018-06-01

There are few studies that forecast the future prevalence of obesity based on the predicted prevalence model including contributing factors. The present study aimed to identify factors associated with obesity and construct forecasting models including significant contributing factors to estimate the 2020 and 2030 prevalence of obesity and abdominal obesity. Panel data from the Korea National Health and Nutrition Examination Survey and national statistics from the Korean Statistical Information Service were used for the analysis. The study subjects were 17,685 male and 24,899 female adults aged 19 years or older. The outcome variables were the prevalence of obesity (body mass index ≥ 25 kg/m 2 ) and abdominal obesity (waist circumference ≥ 90 cm for men and ≥ 85 cm for women). Stepwise logistic regression analysis was used to select significant variables from potential exposures. The survey year, age, marital status, job status, income status, smoking, alcohol consumption, sleep duration, psychological factors, dietary intake, and fertility rate were found to contribute to the prevalence of obesity and abdominal obesity. Based on the forecasting models including these variables, the 2020 and 2030 estimates for obesity prevalence were 47% and 62% for men and 32% and 37% for women, respectively. The present study suggested an increased prevalence of obesity and abdominal obesity in 2020 and 2030. Lifestyle factors were found to be significantly associated with the increasing trend in obesity prevalence and, therefore, they may require modification to prevent the rising trend.

Pitting and Repair of the Space Shuttle's Inconel(Registered TradeMark) Honeycomb Conical Seal Panel

NASA Technical Reports Server (NTRS)

Zimmerman, Frank R.; Gentz, Steven J.; Miller, James B.; MacKay, Rebecca A.; Bright, Mark L.

2006-01-01

During return to flight servicing of the rudder speed brake (RSB) for each Space Shuttle Orbiter, inspectors discovered numerous small pits on the surface of the #4 right hand side honeycomb panel that covers the rudder speed brake actuators. Shortly after detection of the problem, concurrent investigations were initiated to determine the extent of damage, the root cause, and to develop a repair plan, since fabrication of a replacement panel is impractical for cost, schedule, and sourcing considerations. This paper describes the approach, findings, conclusions and recommendations associated with the investigation of the conical seal pitting. It documents the cause and contributing factors of the pitting, the means used to isolate each contributor, and the supporting evidence for the primary cause of the pitting. Finally, the selection, development and verification of the repair procedure used to restore the conical seal panel is described with supporting process and metallurgical rationale for selection.

2006 National Small Business Conference - Meeting DOD/DHS Mission Needs in the 21st Century

DTIC Science & Technology

2006-05-10

Untitled Document National Small Business Conference.html[7/7/2016 1:35:33 PM] National Small Business Conference "Meeting DoD/DHS Mission Needs in...Defense Systems (Will be available soon) Panel: Program Manager’s Perspective on Small Business Contributions to Major Programs • Mr. Michael Hoeffler...Vice President, Future Naval Capability, Raytheon Company Small Business Success Story Panel: • Mr. Jay Boyce, Foster-Miller, Inc. (Will be

Librarian contributions to clinical practice guidelines.

PubMed

Cruse, Peggy; Protzko, Shandra

2014-01-01

Librarians have become more involved in developing high quality systematic reviews. Evidence-based practice guidelines are an extension of systematic reviews and offer another significant area for librarian involvement. This column highlights opportunities and challenges for the librarian working on guideline panels and provides practical considerations for meaningful contributions to the guideline creation process.

Integrated analysis on static/dynamic aeroelasticity of curved panels based on a modified local piston theory

NASA Astrophysics Data System (ADS)

Yang, Zhichun; Zhou, Jian; Gu, Yingsong

2014-10-01

A flow field modified local piston theory, which is applied to the integrated analysis on static/dynamic aeroelastic behaviors of curved panels, is proposed in this paper. The local flow field parameters used in the modification are obtained by CFD technique which has the advantage to simulate the steady flow field accurately. This flow field modified local piston theory for aerodynamic loading is applied to the analysis of static aeroelastic deformation and flutter stabilities of curved panels in hypersonic flow. In addition, comparisons are made between results obtained by using the present method and curvature modified method. It shows that when the curvature of the curved panel is relatively small, the static aeroelastic deformations and flutter stability boundaries obtained by these two methods have little difference, while for curved panels with larger curvatures, the static aeroelastic deformation obtained by the present method is larger and the flutter stability boundary is smaller compared with those obtained by the curvature modified method, and the discrepancy increases with the increasing of curvature of panels. Therefore, the existing curvature modified method is non-conservative compared to the proposed flow field modified method based on the consideration of hypersonic flight vehicle safety, and the proposed flow field modified local piston theory for curved panels enlarges the application range of piston theory.

ACT Payload Shroud Structural Concept Analysis and Optimization

NASA Technical Reports Server (NTRS)

Zalewski, Bart B.; Bednarcyk, Brett A.

2010-01-01

Aerospace structural applications demand a weight efficient design to perform in a cost effective manner. This is particularly true for launch vehicle structures, where weight is the dominant design driver. The design process typically requires many iterations to ensure that a satisfactory minimum weight has been obtained. Although metallic structures can be weight efficient, composite structures can provide additional weight savings due to their lower density and additional design flexibility. This work presents structural analysis and weight optimization of a composite payload shroud for NASA s Ares V heavy lift vehicle. Two concepts, which were previously determined to be efficient for such a structure are evaluated: a hat stiffened/corrugated panel and a fiber reinforced foam sandwich panel. A composite structural optimization code, HyperSizer, is used to optimize the panel geometry, composite material ply orientations, and sandwich core material. HyperSizer enables an efficient evaluation of thousands of potential designs versus multiple strength and stability-based failure criteria across multiple load cases. HyperSizer sizing process uses a global finite element model to obtain element forces, which are statistically processed to arrive at panel-level design-to loads. These loads are then used to analyze each candidate panel design. A near optimum design is selected as the one with the lowest weight that also provides all positive margins of safety. The stiffness of each newly sized panel or beam component is taken into account in the subsequent finite element analysis. Iteration of analysis/optimization is performed to ensure a converged design. Sizing results for the hat stiffened panel concept and the fiber reinforced foam sandwich concept are presented.

Paediatric Automatic Phonological Analysis Tools (APAT).

PubMed

Saraiva, Daniela; Lousada, Marisa; Hall, Andreia; Jesus, Luis M T

2017-12-01

To develop the pediatric Automatic Phonological Analysis Tools (APAT) and to estimate inter and intrajudge reliability, content validity, and concurrent validity. The APAT were constructed using Excel spreadsheets with formulas. The tools were presented to an expert panel for content validation. The corpus used in the Portuguese standardized test Teste Fonético-Fonológico - ALPE produced by 24 children with phonological delay or phonological disorder was recorded, transcribed, and then inserted into the APAT. Reliability and validity of APAT were analyzed. The APAT present strong inter- and intrajudge reliability (>97%). The content validity was also analyzed (ICC = 0.71), and concurrent validity revealed strong correlations between computerized and manual (traditional) methods. The development of these tools contributes to fill existing gaps in clinical practice and research, since previously there were no valid and reliable tools/instruments for automatic phonological analysis, which allowed the analysis of different corpora.

Development of panel loudspeaker system: design, evaluation and enhancement.

PubMed

Bai, M R; Huang, T

2001-06-01

Panel speakers are investigated in terms of structural vibration and acoustic radiation. A panel speaker primarily consists of a panel and an inertia exciter. Contrary to conventional speakers, flexural resonance is encouraged such that the panel vibrates as randomly as possible. Simulation tools are developed to facilitate system integration of panel speakers. In particular, electro-mechanical analogy, finite element analysis, and fast Fourier transform are employed to predict panel vibration and the acoustic radiation. Design procedures are also summarized. In order to compare the panel speakers with the conventional speakers, experimental investigations were undertaken to evaluate frequency response, directional response, sensitivity, efficiency, and harmonic distortion of both speakers. The results revealed that the panel speakers suffered from a problem of sensitivity and efficiency. To alleviate the problem, a woofer using electronic compensation based on H2 model matching principle is utilized to supplement the bass response. As indicated in the result, significant improvement over the panel speaker alone was achieved by using the combined panel-woofer system.

Characterization of the Acoustic Radiation Properties of Laminated and Sandwich Composite Panels in Thermal Environment

NASA Astrophysics Data System (ADS)

Sharma, Nitin; Ranjan Mahapatra, Trupti; Panda, Subrata Kumar; Sahu, Pruthwiraj

2018-03-01

In this article, the acoustic radiation characteristics of laminated and sandwich composite spherical panels subjected to harmonic point excitation under thermal environment are investigated. The finite element (FE) simulation model of the vibrating panel structure is developed in ANSYS using ANSYS parametric design language (APDL) code. Initially, the critical buckling temperatures of the considered structures are obtained and the temperature loads are assorted accordingly. Then, the modal analysis of the thermally stressed panels is performed and the thermo-elastic free vibration responses so obtained are validated with the benchmark solutions. Subsequently, an indirect boundary element (BE) method is utilized to conduct a coupled FE-BE analysis to compute the sound radiation properties of panel structure. The agreement of the present sound power responses with the existing results available in the published literature establishes the validity of the proposed scheme. Finally, the current standardised scheme is extended to solve several numerical examples to bring out the influence of various parameters on the thermo-acoustic characteristics of laminated composite panels.

Fuzzy Structures Analysis of Aircraft Panels in NASTRAN

NASA Technical Reports Server (NTRS)

Sparrow, Victor W.; Buehrle, Ralph D.

2001-01-01

This paper concerns an application of the fuzzy structures analysis (FSA) procedures of Soize to prototypical aerospace panels in MSC/NASTRAN, a large commercial finite element program. A brief introduction to the FSA procedures is first provided. The implementation of the FSA methods is then disclosed, and the method is validated by comparison to published results for the forced vibrations of a fuzzy beam. The results of the new implementation show excellent agreement to the benchmark results. The ongoing effort at NASA Langley and Penn State to apply these fuzzy structures analysis procedures to real aircraft panels is then described.

[Proteome analysis for identification of tumor-associated biomarkers in breast cancer].

PubMed

Wang, Xi; Liang, Wei-Jiang; Zhu, Zhen-Yu; Yang, Ming-Tian; Zeng, Yi-Xin

2004-11-01

Pre-symptomatic screening of early-stage breast cancer may greatly reduce tumor-related mortality. Some tumor markers, such as CA15-3 and CA27-29, are recommended only for monitoring therapy of advanced or relapsed breast cancer. This study was to find new biomarkers that could be used individually or in combination with an existing modality for cost-effective screening of breast cancer by proteome analysis. Protein expression differences among 128 serum samples of 64 breast cancer patients (19 of stage I, 24 of stage II, and 21 of stage III), 52 patients with benign breast diseases, and 12 healthy women were analyzed with IMAC3 and WCX2 Ciphergen ProteinChip Arrays. On WCX2 chip, a panel of 5 proteins (9 116, 8 905, 8 749, 9 470, and 9 692 Da) was selected based on their collective contribution to the optimal separation between breast cancer patients and both non-cancer patients and healthy women, and expression of another 2 proteins (9 405 and 6 424 Da) was different between patients with breast cancer of stage I and stage III. On IMAC3 chip, a panel of 9 proteins (5 236, 7 823, 7 464, 5 213, 5 334, 5 064, 5 374, 7 756, and 7 623 Da) was selected based on their collective contribution to the optimal separation between breast cancer patients and both non-cancer patients and healthy women, and expression of another 3 proteins (7 922, 4 641, and 5 910 Da) was different between patients with breast cancer of stage I and stage III. Protein expression in breast cancer patients is different from that in both non-cancer patients and healthy women, and those proteins with different expression may be used as new biomarkers in breast cancer.

Genome-wide association study in Asia-adapted tropical maize reveals novel and explored genomic regions for sorghum downy mildew resistance.

PubMed

Rashid, Zerka; Singh, Pradeep Kumar; Vemuri, Hindu; Zaidi, Pervez Haider; Prasanna, Boddupalli Maruthi; Nair, Sudha Krishnan

2018-01-10

Globally, downy mildews are among the important foliar diseases of maize that cause significant yield losses. We conducted a genome-wide association study for sorghum downy mildew (SDM; Peronosclerospora sorghi) resistance in a panel of 368 inbred lines adapted to the Asian tropics. High density SNPs from Genotyping-by-sequencing were used in GWAS after controlling for population structure and kinship in the panel using a single locus mixed model. The study identified a set of 26 SNPs that were significantly associated with SDM resistance, with Bonferroni corrected P values ≤ 0.05. Among all the identified SNPs, the minor alleles were found to be favorable to SDM resistance in the mapping panel. Trend regression analysis with 16 independent genetic variants including 12 SNPs and four haplotype blocks identified SNP S2_6154311 on chromosome 2 with P value 2.61E-24 and contributing 26.7% of the phenotypic variation. Six of the SNPs/haplotypes were within the same chromosomal bins as the QTLs for SDM resistance mapped in previous studies. Apart from this, eight novel genomic regions for SDM resistance were identified in this study; they need further validation before being applied in the breeding pipeline. Ten SNPs identified in this study were co-located in reported mildew resistance genes.

Fabrication and Testing of Carbon Fiber, Graphite-Epoxy Panels for Submillimeter Telescope Use

NASA Astrophysics Data System (ADS)

Rieger, H.; Helwig, G.; Parks, R. E.; Ulich, B. L.

1983-12-01

An experimental carbon-fiber, graphite-epoxy, aluminum Flexcore sandwich panel roughly 1-m square was made by Dornier System, Friedrichshafen, West Germany. The panel was a pre-prototype of the panels to be used in the dish of the 10-m diameter Sub-Millimeter Telescope, a joint project of the Max-Planck-Institute fur Radioastronomie, Bonn, West Germany, and Steward Observatory, the University of Arizona in Tucson. This paper outlines the fabrication process for the panel and indicates the surface accuracy of the panel replication process. To predict the behavior of the panel under various environmental loads, the panel was modeled structurally using anisotropic elements for the core material. Results of this analysis along with experimental verification of these predictions are also given.

Spectroscopic characterization of sixteenth century panel painting references using Raman, surface-enhanced Raman spectroscopy and helium-Raman system for in situ analysis of Ibero-American Colonial paintings

NASA Astrophysics Data System (ADS)

García-Bucio, María Angélica; Casanova-González, Edgar; Ruvalcaba-Sil, José Luis; Arroyo-Lemus, Elsa; Mitrani-Viggiano, Alejandro

2016-12-01

Colonial panel paintings constitute an essential part of Latin-American cultural heritage. Their study is vital for understanding the manufacturing process, including its evolution in history, as well as its authorship, dating and other information significant to art history and conservation purposes. Raman spectroscopy supplies a non-destructive characterization tool, which can be implemented for in situ analysis, via portable equipment. Specific methodologies must be developed, comprising the elaboration of reference panel paintings using techniques and materials similar to those of the analysed period, as well as the determination of the best analysis conditions for different pigments and ground preparations. In order to do so, Raman spectroscopy at 532, 785 and 1064 nm, surface-enhanced Raman spectroscopy (SERS) and a helium-Raman system were applied to a panel painting reference, in combination with X-ray fluorescence analysis. We were able to establish the analysis conditions for a number of sixteenth century pigments and dyes, and other relevant components of panel paintings from this period, 1064 nm Raman and SERS being the most successful. The acquired spectra contain valuable specific information for their identification and they conform a very useful database that can be applied to the analysis of Ibero-American Colonial paintings. This article is part of the themed issue "Raman spectroscopy in art and archaeology".

Parentage Reconstruction in Eucalyptus nitens Using SNPs and Microsatellite Markers: A Comparative Analysis of Marker Data Power and Robustness.

PubMed

Telfer, Emily J; Stovold, Grahame T; Li, Yongjun; Silva-Junior, Orzenil B; Grattapaglia, Dario G; Dungey, Heidi S

2015-01-01

Pedigree reconstruction using molecular markers enables efficient management of inbreeding in open-pollinated breeding strategies, replacing expensive and time-consuming controlled pollination. This is particularly useful in preferentially outcrossed, insect pollinated Eucalypts known to suffer considerable inbreeding depression from related matings. A single nucleotide polymorphism (SNP) marker panel consisting of 106 markers was selected for pedigree reconstruction from the recently developed high-density Eucalyptus Infinium SNP chip (EuCHIP60K). The performance of this SNP panel for pedigree reconstruction in open-pollinated progenies of two Eucalyptus nitens seed orchards was compared with that of two microsatellite panels with 13 and 16 markers respectively. The SNP marker panel out-performed one of the microsatellite panels in the resolution power to reconstruct pedigrees and out-performed both panels with respect to data quality. Parentage of all but one offspring in each clonal seed orchard was correctly matched to the expected seed parent using the SNP marker panel, whereas parentage assignment to less than a third of the expected seed parents were supported using the 13-microsatellite panel. The 16-microsatellite panel supported all but one of the recorded seed parents, one better than the SNP panel, although there was still a considerable level of missing and inconsistent data. SNP marker data was considerably superior to microsatellite data in accuracy, reproducibility and robustness. Although microsatellites and SNPs data provide equivalent resolution for pedigree reconstruction, microsatellite analysis requires more time and experience to deal with the uncertainties of allele calling and faces challenges for data transferability across labs and over time. While microsatellite analysis will continue to be useful for some breeding tasks due to the high information content, existing infrastructure and low operating costs, the multi-species SNP resource available with the EuCHIP60k, opens a whole new array of opportunities for high-throughput, genome-wide or targeted genotyping in species of Eucalyptus.

Characterization of anticancer agents by their growth inhibitory activity and relationships to mechanism of action and structure.

PubMed

Keskin, O; Bahar, I; Jernigan, R L; Beutler, J A; Shoemaker, R H; Sausville, E A; Covell, D G

2000-04-01

An analysis of the growth inhibitory potency of 122 anticancer agents available from the National Cancer Institute anticancer drug screen is presented. Methods of singular value decomposition (SVD) were applied to determine the matrix of distances between all compounds. These SVD-derived dissimilarity distances were used to cluster compounds that exhibit similar tumor growth inhibitory activity patterns against 60 human cancer cell lines. Cluster analysis divides the 122 standard agents into 25 statistically distinct groups. The first eight groups include structurally diverse compounds with reactive functionalities that act as DNA-damaging agents while the remaining 17 groups include compounds that inhibit nucleic acid biosynthesis and mitosis. Examination of the average activity patterns across the 60 tumor cell lines reveals unique 'fingerprints' associated with each group. A diverse set of structural features are observed for compounds within these groups, with frequent occurrences of strong within-group structural similarities. Clustering of cell types by their response to the 122 anticancer agents divides the 60 cell types into 21 groups. The strongest within-panel groupings were found for the renal, leukemia and ovarian cell panels. These results contribute to the basis for comparisons between log(GI(50)) screening patterns of the 122 anticancer agents and additional tested compounds.

(Pea)nuts and bolts of visual narrative: Structure and meaning in sequential image comprehension

PubMed Central

Cohn, Neil; Paczynski, Martin; Jackendoff, Ray; Holcomb, Phillip J.; Kuperberg, Gina R.

2012-01-01

Just as syntax differentiates coherent sentences from scrambled word strings, the comprehension of sequential images must also use a cognitive system to distinguish coherent narrative sequences from random strings of images. We conducted experiments analogous to two classic studies of language processing to examine the contributions of narrative structure and semantic relatedness to processing sequential images. We compared four types of comic strips: 1) Normal sequences with both structure and meaning, 2) Semantic Only sequences (in which the panels were related to a common semantic theme, but had no narrative structure), 3) Structural Only sequences (narrative structure but no semantic relatedness), and 4) Scrambled sequences of randomly-ordered panels. In Experiment 1, participants monitored for target panels in sequences presented panel-by-panel. Reaction times were slowest to panels in Scrambled sequences, intermediate in both Structural Only and Semantic Only sequences, and fastest in Normal sequences. This suggests that both semantic relatedness and narrative structure offer advantages to processing. Experiment 2 measured ERPs to all panels across the whole sequence. The N300/N400 was largest to panels in both the Scrambled and Structural Only sequences, intermediate in Semantic Only sequences and smallest in the Normal sequences. This implies that a combination of narrative structure and semantic relatedness can facilitate semantic processing of upcoming panels (as reflected by the N300/N400). Also, panels in the Scrambled sequences evoked a larger left-lateralized anterior negativity than panels in the Structural Only sequences. This localized effect was distinct from the N300/N400, and appeared despite the fact that these two sequence types were matched on local semantic relatedness between individual panels. These findings suggest that sequential image comprehension uses a narrative structure that may be independent of semantic relatedness. Altogether, we argue that the comprehension of visual narrative is guided by an interaction between structure and meaning. PMID:22387723

Fabrication of prepackaged superalloy honeycomb Thermal Protection System (TPS) panels

NASA Technical Reports Server (NTRS)

Blair, W.; Meaney, J. E.; Rosenthal, H. A.

1985-01-01

High temperature materials were surveyed, and Inconel 617 and titanium were selected for application to a honeycomb TPS configuration designed to withstand 2000 F. The configuration was analyzed both thermally and structurally. Component and full-sized panels were fabricated and tested to obtain data for comparison with analysis. Results verified the panel design. Twenty five panels were delivered to NASA Langley Research Center for additional evaluation.

Thermostructural Behavior of a Hypersonic Aircraft Sandwich Panel Subjected to Heating on One Side

NASA Technical Reports Server (NTRS)

Ko, William L.

1997-01-01

Thermostructural analysis was performed on a heated titanium honeycomb-core sandwich panel. The sandwich panel was supported at its four edges with spar-like substructures that acted as heat sinks, which are generally not considered in the classical analysis. One side of the panel was heated to high temperature to simulate aerodynamic heating during hypersonic flight. Two types of surface heating were considered: (1) flat-temperature profile, which ignores the effect of edge heat sinks, and (2) dome-shaped-temperature profile, which approximates the actual surface temperature distribution associated with the existence of edge heat sinks. The finite-element method was used to calculate the deformation field and thermal stress distributions in the face sheets and core of the sandwich panel. The detailed thermal stress distributions in the sandwich panel are presented, and critical stress regions are identified. The study shows how the magnitudes of those critical stresses and their locations change with different heating and edge conditions. This technical report presents comprehensive, three-dimensional graphical displays of thermal stress distributions in every part of a titanium honeycomb-core sandwich panel subjected to hypersonic heating on one side. The plots offer quick visualization of the structural response of the panel and are very useful for hot structures designers to identify the critical stress regions.

Fracture analysis of stiffened panels under biaxial loading with widespread cracking

NASA Technical Reports Server (NTRS)

Newman, J. C., Jr.; Dawicke, D. S.

1995-01-01

An elastic-plastic finite-element analysis with a critical crack-tip-opening angle (CTOA) fracture criterion was used to model stable crack growth and fracture of 2024-T3 aluminum alloy (bare and clad) panels for several thicknesses. The panels had either single or multiple-site damage (MSD) cracks subjected to uniaxial or biaxial loading. Analyses were also conducted on cracked stiffened panels with single or MSD cracks. The critical CTOA value for each thickness was determined by matching the failure load on a middle-crack tension specimen. Comparisons were made between the critical angles determined from the finite-element analyses and those measured with photographic methods. Predicted load-against-crack extension and failure loads for panels under biaxial loading, panels with MSD cracks, and panels with various number of stiffeners were compared with test data, whenever possible. The predicted results agreed well with the test data even for large-scale plastic deformations. The analyses were also able to predict stable tearing behavior of a large lead crack in the presence of MSD cracks. The analyses were then used to study the influence of stiffeners on residual strength in the presence of widespread fatigue cracking. Small MSD cracks were found to greatly reduce the residual strength for large lead cracks even for stiffened panels.

Fracture analysis of stiffened panels under biaxial loading with widespread cracking

NASA Technical Reports Server (NTRS)

Newman, J. C., Jr.

1995-01-01

An elastic-plastic finite-element analysis with a critical crack-tip opening angle (CTOA) fracture criterion was used to model stable crack growth and fracture of 2024-T3 aluminum alloy (bare and clad) panels for several thicknesses. The panels had either single or multiple-site damage (MSD) cracks subjected to uniaxial or biaxial loading. Analyses were also conducted on cracked stiffened panels with single or MSD cracks. The critical CTOA value for each thickness was determined by matching the failure load on a middle-crack tension specimen. Comparisons were made between the critical angles determined from the finite-element analyses and those measured with photographic methods. Predicted load-against-crack extension and failure loads for panels under biaxial loading, panels with MSD cracks, and panels with various numbers of stiffeners were compared with test data whenever possible. The predicted results agreed well with the test data even for large-scale plastic deformations. The analyses were also able to predict stable tearing behavior of a large lead crack in the presence of MSD cracks. The analyses were then used to study the influence of stiffeners on residual strength in the presence of widespread fatigue cracking. Small MSD cracks were found to greatly reduce the residual strength for large lead cracks even for stiffened panels.

Panel positioning error and support mechanism for a 30-m THz radio telescope

NASA Astrophysics Data System (ADS)

Yang, De-Hua; Okoh, Daniel; Zhou, Guo-Hua; Li, Ai-Hua; Li, Guo-Ping; Cheng, Jing-Quan

2011-06-01

A 30-m TeraHertz (THz) radio telescope is proposed to operate at 200 μm with an active primary surface. This paper presents sensitivity analysis of active surface panel positioning errors with optical performance in terms of the Strehl ratio. Based on Ruze's surface error theory and using a Monte Carlo simulation, the effects of six rigid panel positioning errors, such as piston, tip, tilt, radial, azimuthal and twist displacements, were directly derived. The optical performance of the telescope was then evaluated using the standard Strehl ratio. We graphically illustrated the various panel error effects by presenting simulations of complete ensembles of full reflector surface errors for the six different rigid panel positioning errors. Study of the panel error sensitivity analysis revealed that the piston error and tilt/tip errors are dominant while the other rigid errors are much less important. Furthermore, as indicated by the results, we conceived of an alternative Master-Slave Concept-based (MSC-based) active surface by implementating a special Series-Parallel Concept-based (SPC-based) hexapod as the active panel support mechanism. A new 30-m active reflector based on the two concepts was demonstrated to achieve correction for all the six rigid panel positioning errors in an economically feasible way.

75 FR 10545 - Occupational Information Development Advisory Panel Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-08

... following areas: Medical and vocational analysis of disability claims; occupational analysis, including... system suited to its disability programs and improve the medical-vocational adjudication policies and... remaining time to deliberate or conduct other Panel business. Those interested in providing testimony in...

Configuration and Sizing of a Test Fixture for Panels Under Combined Loads

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.

2006-01-01

Future air and space structures are expected to utilize composite panels that are subjected to combined mechanical loads, such as bi-axial compression/tension, shear and pressure. Therefore, the ability to accurately predict the buckling and strength failures of such panels is important. While computational analysis can provide tremendous insight into panel response, experimental results are necessary to verify predicted performances of these panels to judge the accuracy of computational methods. However, application of combined loads is an extremely difficult task due to the complex test fixtures and set-up required. Presented herein is a comparison of several test set-ups capable of testing panels under combined loads. Configurations compared include a D-box, a segmented cylinder and a single panel set-up. The study primarily focuses on the preliminary sizing of a single panel test configuration capable of testing flat panels under combined in-plane mechanical loads. This single panel set-up appears to be best suited to the testing of both strength critical and buckling critical panels. Required actuator loads and strokes are provided for various square, flat panels.

An Analysis of the Use of Energy Audits, Solar Panels, and Wind Turbines to Reduce Energy Consumption from Non Renewable Energy Sources

DTIC Science & Technology

2015-04-15

the Use of Energy Audits, Solar Panels, and Wind Turbines to Reduce Energy Consumption from Non Renewable Energy Sources Energy is a National...Park, NC 27709-2211 Energy Audits, Energy Conservation, Renewable Energy, Solar Energy, Wind Turbine Use, Energy Consumption REPORT DOCUMENTATION PAGE 11...in non peer-reviewed journals: An Analysis of the Use of Energy Audits, Solar Panels, and Wind Turbines to Reduce Energy Consumption from Non

Novel Composites for Wing and Fuselage Applications

NASA Technical Reports Server (NTRS)

Suarez, J. A.; Buttitta, C.

1996-01-01

Design development was successfully completed for textile preforms with continuous cross-stiffened epoxy panels with cut-outs. The preforms developed included 3-D angle interlock weaving of graphite structural fibers impregnated by resin film infiltration (RFI) and shown to be structurally suitable under conditions requiring minimum acquisition costs. Design guidelines/analysis methodology for such textile structures are given. The development was expanded to a fuselage side-panel component of a subsonic commercial airframe and found to be readily scalable. The successfully manufactured panel was delivered to NASA Langley for biaxial testing. This report covers the work performed under Task 3 -- Cross-Stiffened Subcomponent; Task 4 -- Design Guidelines/Analysis of Textile-Reinforced Composites; and Task 5 -- Integrally Woven Fuselage Panel.

Current research on shear buckling and thermal loads with PASCO: Panel Analysis and Sizing Code

NASA Technical Reports Server (NTRS)

Stroud, W. J.; Greene, W. H.; Anderson, M. S.

1981-01-01

The PASCO computer program to obtain the detailed dimensions of optimum stiffened composite structural panels is described. Design requirements in terms of inequality constraints can be placed on buckling loads or vibration frequencies, lamina stresses and strains, and overall panel stiffness for each of many load conditions. General panel cross sections can be treated. An analysis procedure involving a smeared orthotropic solution was investigated. The conservatism in the VIPASA solution and the danger in a smeared orthotropic solution is explored. PASCO's capability to design for thermal loadings is also described. It is emphasized that design studies illustrate the importance of the multiple load condition capability when thermal loads are present.

Patient safety in out-of-hours primary care: a review of patient records.

PubMed

Smits, Marleen; Huibers, Linda; Kerssemeijer, Brian; de Feijter, Eimert; Wensing, Michel; Giesen, Paul

2010-12-10

Most patients receive healthcare in primary care settings, but relatively little is known about patient safety. Out-of-hours contacts are of particular importance to patient safety. Our aim was to examine the incidence, types, causes, and consequences of patient safety incidents at general practice cooperatives for out-of-hours primary care and to examine which factors were associated with the occurrence of patient safety incidents. A retrospective study of 1,145 medical records concerning patient contacts with four general practice cooperatives. Reviewers identified records with evidence of a potential patient safety incident; a physician panel determined whether a patient safety incident had indeed occurred. In addition, the panel determined the type, causes, and consequences of the incidents. Factors associated with incidents were examined in a random coefficient logistic regression analysis. In 1,145 patient records, 27 patient safety incidents were identified, an incident rate of 2.4% (95% CI: 1.5% to 3.2%). The most frequent incident type was treatment (56%). All incidents had at least partly been caused by failures in clinical reasoning. The majority of incidents did not result in patient harm (70%). Eight incidents had consequences for the patient, such as additional interventions or hospitalisation. The panel assessed that most incidents were unlikely to result in patient harm in the long term (89%). Logistic regression analysis showed that age was significantly related to incident occurrence: the likelihood of an incident increased with 1.03 for each year increase in age (95% CI: 1.01 to 1.04). Patient safety incidents occur in out-of-hours primary care, but most do not result in harm to patients. As clinical reasoning played an important part in these incidents, a better understanding of clinical reasoning and guideline adherence at GP cooperatives could contribute to patient safety.

Immunophenotypical characterization of canine mesenchymal stem cells from perivisceral and subcutaneous adipose tissue by a species-specific panel of antibodies.

PubMed

Ivanovska, Ana; Grolli, Stefano; Borghetti, Paolo; Ravanetti, Francesca; Conti, Virna; De Angelis, Elena; Macchi, Francesca; Ramoni, Roberto; Martelli, Paolo; Gazza, Ferdinando; Cacchioli, Antonio

2017-10-01

Immunophenotypical characterization of mesenchymal stem cells is fundamental for the design and execution of sound experimental and clinical studies. The scarce availability of species-specific antibodies for canine antigens has hampered the immunophenotypical characterization of canine mesenchymal stem cells (MSC). The aim of this study was to select a panel of species-specific direct antibodies readily useful for canine mesenchymal stem cells characterization. They were isolated from perivisceral and subcutaneous adipose tissue samples collected during regular surgeries from 8 dogs. Single color flow cytometric analysis of mesenchymal stem cells (P3) deriving from subcutaneous and perivisceral adipose tissue with a panel of 7 direct anti-canine antibodies revealed two largely homogenous cell populations with a similar pattern: CD29 + , CD44 + , CD73 + , CD90 + , CD34 - , CD45 - and MHC-II - with no statistically significant differences among them. Antibody reactivity was demonstrated on canine peripheral blood mononuclear cells. The similarities are reinforced by their in vitro cell morphology, trilineage differentiation ability and RT-PCR analysis (CD90 + , CD73 + , CD105 + , CD44 + , CD13 + , CD29 + , Oct-4 + gene and CD31 - and CD45 - expression). Our results report for the first time a comparison between the immunophenotypic profile of canine MSC deriving from perivisceral and subcutaneous adipose tissue. The substantial equivalence between the two populations has practical implication on clinical applications, giving the opportunity to choose the source depending on the patient needs. The results contribute to routine characterization of MSC populations grown in vitro, a mandatory process for the definition of solid and reproducible laboratory and therapeutic procedures. Copyright © 2017 Elsevier Ltd. All rights reserved.

A full-spectrum analysis of high-speed train interior noise under multi-physical-field coupling excitations

NASA Astrophysics Data System (ADS)

Zheng, Xu; Hao, Zhiyong; Wang, Xu; Mao, Jie

2016-06-01

High-speed-railway-train interior noise at low, medium, and high frequencies could be simulated by finite element analysis (FEA) or boundary element analysis (BEA), hybrid finite element analysis-statistical energy analysis (FEA-SEA) and statistical energy analysis (SEA), respectively. First, a new method named statistical acoustic energy flow (SAEF) is proposed, which can be applied to the full-spectrum HST interior noise simulation (including low, medium, and high frequencies) with only one model. In an SAEF model, the corresponding multi-physical-field coupling excitations are firstly fully considered and coupled to excite the interior noise. The interior noise attenuated by sound insulation panels of carriage is simulated through modeling the inflow acoustic energy from the exterior excitations into the interior acoustic cavities. Rigid multi-body dynamics, fast multi-pole BEA, and large-eddy simulation with indirect boundary element analysis are first employed to extract the multi-physical-field excitations, which include the wheel-rail interaction forces/secondary suspension forces, the wheel-rail rolling noise, and aerodynamic noise, respectively. All the peak values and their frequency bands of the simulated acoustic excitations are validated with those from the noise source identification test. Besides, the measured equipment noise inside equipment compartment is used as one of the excitation sources which contribute to the interior noise. Second, a full-trimmed FE carriage model is firstly constructed, and the simulated modal shapes and frequencies agree well with the measured ones, which has validated the global FE carriage model as well as the local FE models of the aluminum alloy-trim composite panel. Thus, the sound transmission loss model of any composite panel has indirectly been validated. Finally, the SAEF model of the carriage is constructed based on the accurate FE model and stimulated by the multi-physical-field excitations. The results show that the trend of the simulated 1/3 octave band sound pressure spectrum agrees well with that of the on-site-measured one. The deviation between the simulated and measured overall sound pressure level (SPL) is 2.6 dB(A) and well controlled below the engineering tolerance limit, which has validated the SAEF model in the full-spectrum analysis of the high speed train interior noise.

Dental Care Every Day: A Caregiver's Guide

MedlinePlus

... oral health professionals and caregivers who contributed their time and expertise to reviewing and pretesting the Practical Oral Care series. Expert Review Panel • Mae Chin, RDH, MEd, University ...

Liquid Hydrogen Regulated Low Pressure High Flow Pneumatic Panel AFT Arrow Analysis

NASA Technical Reports Server (NTRS)

Jones, Kelley, M.

2013-01-01

Project Definition: Design a high flow pneumatic regulation panel to be used with helium and hydrogen. The panel will have two circuits, one for gaseous helium (GHe) supplied from the GHe Movable Storage Units (MSUs) and one for gaseous hydrogen (GH2) supplied from an existing GH2 Fill Panel. The helium will supply three legs; to existing panels and on the higher pressure leg and Simulated Flight Tanks (SFTs) for the lower pressure legs. The hydrogen line will pressurize a 33,000 gallon vacuum jacketed vessel.

Youth Violence. Hearings before the Committee on the Judiciary. United States Senate, One Hundred Fourth Congress, First Session Focusing on the Cause of Juvenile Crime and the Need for Juvenile Justice Reform (Dover and Wilmington, DE, July 15 and 17, 1995).

ERIC Educational Resources Information Center

Congress of the U.S., Washington, DC. Senate Committee on the Judiciary.

This hearing focused on the cause of juvenile crime and the need for juvenile justice reform. On the first day, an opening statement by Senator Joseph R. Biden examined the seriousness of the problem. Two panels contributed prepared statements. The first panel included Jim Hutchinson, Mayor, Dover, DE; Alan Ellingsworth, Colonel, Delaware State…

Fatigue analysis of multiple site damage at a row of holes in a wide panel

NASA Technical Reports Server (NTRS)

Buhler, Kimberley; Grandt, Alten F., Jr.; Moukawsher, E. J.

1994-01-01

This paper is concerned with predicting the fatigue life of unstiffened panels which contain multiple site damage (MSD). The initial damage consists of through-the-thickness cracks emanating from a row of holes in the center of a finite width panel. A fracture mechanics analysis has been developed to predict the growth, interaction, and coalescence of the various cracks which propagate in the panel. A strain-life analysis incorporating Neuber's rule for notches, and Miner's rule for cumulative damage, is also employed to predict crack initiation for holes without initial cracking. This analysis is compared with the results of a series of fatigue tests on 2024-T3 aluminum panels, and is shown to do an excellent job of predicting the influence of MSD on the fatigue life of nine inch wide specimens. Having established confidence in the ability to analyze the influence of MSD on fatigue life, a parametric study is conducted to examine the influence of various MSD scenarios in an unstiffened panel. The numerical study considered 135 cases in all, with the parametric variables being the applied cyclic stress level, the lead crack geometry, and the number and location of MSD cracks. The numerical analysis provides details for the manner in which lead cracks and MSD cracks grow and coalesce leading to final failure. The results indicate that MSD located adjacent to lead cracks is the most damaging configuration, while for cases without lead cracks, MSD clusters which are not separated by uncracked holes are most damaging.

Analysis of hourly crash likelihood using unbalanced panel data mixed logit model and real-time driving environmental big data.

PubMed

Chen, Feng; Chen, Suren; Ma, Xiaoxiang

2018-06-01

Driving environment, including road surface conditions and traffic states, often changes over time and influences crash probability considerably. It becomes stretched for traditional crash frequency models developed in large temporal scales to capture the time-varying characteristics of these factors, which may cause substantial loss of critical driving environmental information on crash prediction. Crash prediction models with refined temporal data (hourly records) are developed to characterize the time-varying nature of these contributing factors. Unbalanced panel data mixed logit models are developed to analyze hourly crash likelihood of highway segments. The refined temporal driving environmental data, including road surface and traffic condition, obtained from the Road Weather Information System (RWIS), are incorporated into the models. Model estimation results indicate that the traffic speed, traffic volume, curvature and chemically wet road surface indicator are better modeled as random parameters. The estimation results of the mixed logit models based on unbalanced panel data show that there are a number of factors related to crash likelihood on I-25. Specifically, weekend indicator, November indicator, low speed limit and long remaining service life of rutting indicator are found to increase crash likelihood, while 5-am indicator and number of merging ramps per lane per mile are found to decrease crash likelihood. The study underscores and confirms the unique and significant impacts on crash imposed by the real-time weather, road surface, and traffic conditions. With the unbalanced panel data structure, the rich information from real-time driving environmental big data can be well incorporated. Copyright © 2018 National Safety Council and Elsevier Ltd. All rights reserved.

Extra-epitopic hepatitis C virus polymorphisms confer resistance to broadly neutralizing antibodies by modulating binding to scavenger receptor B1.

PubMed

El-Diwany, Ramy; Cohen, Valerie J; Mankowski, Madeleine C; Wasilewski, Lisa N; Brady, Jillian K; Snider, Anna E; Osburn, William O; Murrell, Ben; Ray, Stuart C; Bailey, Justin R

2017-02-01

Broadly-neutralizing monoclonal antibodies (bNAbs) may guide vaccine development for highly variable viruses including hepatitis C virus (HCV), since they target conserved viral epitopes that could serve as vaccine antigens. However, HCV resistance to bNAbs could reduce the efficacy of a vaccine. HC33.4 and AR4A are two of the most potent anti-HCV human bNAbs characterized to date, binding to highly conserved epitopes near the amino- and carboxy-terminus of HCV envelope (E2) protein, respectively. Given their distinct epitopes, it was surprising that these bNAbs showed similar neutralization profiles across a panel of natural HCV isolates, suggesting that some viral polymorphisms may confer resistance to both bNAbs. To investigate this resistance, we developed a large, diverse panel of natural HCV envelope variants and a novel computational method to identify bNAb resistance polymorphisms in envelope proteins (E1 and E2). By measuring neutralization of a panel of HCV pseudoparticles by 10 μg/mL of each bNAb, we identified E1E2 variants with resistance to one or both bNAbs, despite 100% conservation of the AR4A binding epitope across the panel. We discovered polymorphisms outside of either binding epitope that modulate resistance to both bNAbs by altering E2 binding to the HCV co-receptor, scavenger receptor B1 (SR-B1). This study is focused on a mode of neutralization escape not addressed by conventional analysis of epitope conservation, highlighting the contribution of extra-epitopic polymorphisms to bNAb resistance and presenting a novel mechanism by which HCV might persist even in the face of an antibody response targeting multiple conserved epitopes.

Service user reflections on the impact of involvement in research.

PubMed

Gordon, Jim; Franklin, Sue; Eltringham, Sabrina A

2018-01-01

Public involvement can impact on research, on the public who give advice, on the researchers and the research participants. Evaluating impact is an important part of the research process. Two members of a hospital-based patient research panel and our coordinator have written this paper. Our panel covers a range of rehabilitation and palliative services. These services form the "Therapeutics and Palliative Care Directorate". We describe how we worked collaboratively with hospital staff and co-produced questionnaires to evaluate the impact of our involvement. We compared the different perspectives of the researchers and panel members on our contribution to the research. We present evidence from these different standpoints, including how our panel made a difference. We found we needed to adapt how we collected the views of the researchers and our members to ensure it was meaningful to our group whilst delivering the wider objective of the hospital. A key finding has been how our involvement has extended into other groups, which has identified opportunities for sharing resources and experience, including areas such as cost effectiveness. Our two-person membership of a high level Board of Academics and Senior Clinicians, which oversees the research we contribute to, has resulted in our opinions influencing the heart of the Directorate's research strategy. We have learned the importance of a flexible approach as the Directorate changes, and the demands on us grow. This will continue to help us share our own development, successes and experience and extend the benefits from working this way. Background Reports about the impact of patient and public involvement in research can be improved by involving patients and research staff more collaboratively to co-produce instruments to measure their involvement. This commentary, written by two members of a hospital-based patient panel and their coordinator for its work, describes how we co-produced instruments to evaluate the impact and effectiveness of our involvement. We present here the results, including our quantitative and qualitative findings, of this patient led evaluation and reflect on how our involvement has made a difference to the research projects and research infrastructure within the hospital in which we operate and on us as a panel. Methods Existing impact frameworks and guidelines were reviewed. Members co-produced and piloted qualitative questionnaires to identify values associated with patient and public involvement (PPI) from both a researcher and panel member perspective, and collected quantitative metrics to provide descriptive statistics on the type of involvement and activities. Members also produced a comments slip to provide contemporaneous feedback after each meeting. Results The panel has reviewed 36 research projects for the Therapeutics and Palliative Care Directorate drawn from speech and language therapy, physiotherapy, occupational therapy, dietetics, podiatry, palliative care services and chaplaincy. Some of the main results of our involvement have been the development of grant applications and making written information more understandable for research participants. Examples of how the Panel made a difference included providing an effective forum for debate by providing practical suggestions to improve research design and identifying potential issues that may not have occurred to the researcher. The panel has had an impact outside of meetings both within the context in which it operates and on the individuals involved. Examples included: influencing the Directorate research agenda, sharing resources with other groups, developing research relationships, and enabling member participation in different roles and settings. Discussion Embedding ourselves within the Directorate research infrastructure has enabled us to adapt to organisational change and actively contribute to the research strategy. There is greater scope for involvement in areas of cost effectiveness and economic evaluation. Increasing member contributions and networking with other groups provides added value as well as cross fertilisation of ideas as part of our widening impact. Conclusion Evaluating the impact of our involvement has improved our understanding of what aspects of involvement work best for the panel and the researchers who attend our meetings, and in the different settings that we work in. It has helped us to focus on how we need to develop to maximise our resources going forward.

Reactivity of polymeric proanthocyanidins toward salivary proteins and their contribution to young red wine astringency.

PubMed

Sun, Baoshan; de Sá, Marta; Leandro, Conceição; Caldeira, Ilda; Duarte, Filomena L; Spranger, Isabel

2013-01-30

Recent studies have indicated the presence of significant amount of highly polymerized and soluble proanthocyanidins in red wine and such compounds interacted readily with proteins, suggesting that they might be particularly astringent. Thus, the objective of this work was to verify the astringency of polymeric proanthocyanidins and their contribution to red wine astringency. The precipitation reactions of the purified oligomeric procyanidins (degree of polymerization ranging from 2 to 12-15) and polymeric procyanidins (degree of polymerization ranging from 12-15 to 32-34) with human salivary proteins were studied; salivary proteins composition changes before and after the reaction was verified by SDS-PAGE and procyanidins composition changes by spectrometric, direct HPLC and thiolysis-HPLC methods. The astringency intensity of these two procyanidin fractions was evaluated by a sensory analysis panel. For verifying the correlation between polymeric proanthocyanidins and young red wine astringency, the levels of total oligomeric and total polymeric proanthocyanidins and other phenolic composition in various young red wines were quantified and the astringency intensities of these wines were evaluated by a sensory panel. The results showed that polymeric proanthocyanidins had much higher reactivity toward human salivary proteins and higher astringency intensity than the oligomeric ones. Furthermore, young red wine astringency intensities were highly correlated to levels of polymeric proanthocyanidins, particularly at low concentration range (correlation coefficient r = 0.9840) but not significant correlated to total polyphenols (r = 0.2343) or other individual phenolic compounds (generally r < 0.3). These results indicate the important contribution of polymeric proanthocyanidins to red wine astringency and the levels of polymeric polyphenols in red wines may be used as an indicator for its astringency.

77 FR 13172 - Occupational Information Development Advisory Panel Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-05

... recommendations will relate to our disability programs in the following areas: Medical and vocational analysis of... medical-vocational adjudication policies and processes. Agenda: The panel will meet on Thursday, March 22... allotted, the panel may use any remaining time to deliberate or conduct other business. Those interested in...

GrigoraSNPs: Optimized Analysis of SNPs for DNA Forensics.

PubMed

Ricke, Darrell O; Shcherbina, Anna; Michaleas, Adam; Fremont-Smith, Philip

2018-04-16

High-throughput sequencing (HTS) of single nucleotide polymorphisms (SNPs) enables additional DNA forensic capabilities not attainable using traditional STR panels. However, the inclusion of sets of loci selected for mixture analysis, extended kinship, phenotype, biogeographic ancestry prediction, etc., can result in large panel sizes that are difficult to analyze in a rapid fashion. GrigoraSNP was developed to address the allele-calling bottleneck that was encountered when analyzing SNP panels with more than 5000 loci using HTS. GrigoraSNPs uses a MapReduce parallel data processing on multiple computational threads plus a novel locus-identification hashing strategy leveraging target sequence tags. This tool optimizes the SNP calling module of the DNA analysis pipeline with runtimes that scale linearly with the number of HTS reads. Results are compared with SNP analysis pipelines implemented with SAMtools and GATK. GrigoraSNPs removes a computational bottleneck for processing forensic samples with large HTS SNP panels. Published 2018. This article is a U.S. Government work and is in the public domain in the USA.

Does network topology influence systemic risk contribution? A perspective from the industry indices in Chinese stock market

PubMed Central

Long, Haiming; Tang, Nengyu

2017-01-01

This study considers the effect of an industry’s network topology on its systemic risk contribution to the stock market using data from the CSI 300 two-tier industry indices from the Chinese stock market. We first measure industry’s conditional-value-at-risk (CoVaR) and the systemic risk contribution (ΔCoVaR) using the fitted time-varying t-copula function. The network of the stock industry is established based on dynamic conditional correlations with the minimum spanning tree. Then, we investigate the connection characteristics and topology of the network. Finally, we utilize seemingly unrelated regression estimation (SUR) of panel data to analyze the relationship between network topology of the stock industry and the industry’s systemic risk contribution. The results show that the systemic risk contribution of small-scale industries such as real estate, food and beverage, software services, and durable goods and clothing, is higher than that of large-scale industries, such as banking, insurance and energy. Industries with large betweenness centrality, closeness centrality, and clustering coefficient and small node occupancy layer are associated with greater systemic risk contribution. In addition, further analysis using a threshold model confirms that the results are robust. PMID:28683130

Do School Lunches Contribute to Childhood Obesity?

ERIC Educational Resources Information Center

Schanzenbach, Diane Whitmore

2009-01-01

This paper assesses whether school lunches contribute to childhood obesity. I employ two methods to isolate the causal impact of school lunches on obesity. First, using panel data, I ?nd that children who consume school lunches are more likely to be obese than those who brown bag their lunches even though they enter kindergarten with the same…

The Field of Child and Youth Care: Are We There Yet?

ERIC Educational Resources Information Center

Freeman, James

2013-01-01

This article presents a brief history of organized child and youth care in North America, reviews contributing factors to the growth of the field as a profession, and explores the motivation of practitioners and organizations to contribute to the ongoing development of the field. Included is a panel discussion with four leading experts on…

Hypervelocity Impact Testing of IM7/977-3 with Micro-Sized Particles

NASA Technical Reports Server (NTRS)

Smith, J. G.; Jegley, D. C.; Siochi, E. J.; Wells, B. K.

2010-01-01

Ground-based hypervelocity imapct testing was conducted on IM7/977-3 quasi-isotropic flat panels at normal incidence using micron-sized particles (i.e. less than or equal to 100 microns) of soda lime glass and olivine. Testing was performed at room temperature (RT) and 175 C with results from the 175 C test compared to those obtained at RT. Between 10 and 30 particles with velocities ranging from 5 to 13 km/s impacted each panel surface for each test temperature. Panels were ultrasonically scanned prior to and after impact testing to assess internal damage. Post-impact analysis included microscopic examination of the surface, determination of particle speed and location, and photomicroscopy for microcrack assessment. Internal damage was observed by ultrasonic inspection on panels impacted at 175 C, whereas damage for the RT impacted panels was confined to surface divets/craters as determined by microscopic analysis.

Panel data analysis of cardiotocograph (CTG) data.

PubMed

Horio, Hiroyuki; Kikuchi, Hitomi; Ikeda, Tomoaki

2013-01-01

Panel data analysis is a statistical method, widely used in econometrics, which deals with two-dimensional panel data collected over time and over individuals. Cardiotocograph (CTG) which monitors fetal heart rate (FHR) using Doppler ultrasound and uterine contraction by strain gage is commonly used in intrapartum treatment of pregnant women. Although the relationship between FHR waveform pattern and the outcome such as umbilical blood gas data at delivery has long been analyzed, there exists no accumulated FHR patterns from large number of cases. As time-series economic fluctuations in econometrics such as consumption trend has been studied using panel data which consists of time-series and cross-sectional data, we tried to apply this method to CTG data. The panel data composed of a symbolized segment of FHR pattern can be easily handled, and a perinatologist can get the whole FHR pattern view from the microscopic level of time-series FHR data.

Analysis of Composite Panel-Stiffener Debonding Using a Shell/3D Modeling Technique

NASA Technical Reports Server (NTRS)

Krueger, Ronald; Minguet, Pierre J.

2006-01-01

Interlaminar fracture mechanics has proven useful for characterizing the onset of delaminations in composites and has been used with limited success primarily to investigate onset in fracture toughness specimens and laboratory size coupon type specimens. Future acceptance of the methodology by industry and certification authorities however, requires the successful demonstration of the methodology on structural level. For this purpose a panel was selected that was reinforced with stringers. Shear loading cases the panel to buckle and the resulting out-of-plane deformations initiate skin/stringer separation at the location of an embedded defect. For finite element analysis, the panel and surrounding load fixture were modeled with shell element. A small section of the stringer foot and the panel in the vicinity of the embedded defect were modeled with a local 3D solid model. A failure index was calculated by correlating computed mixed-mode failure criterion of the graphite/epoxy material.

Analysis/design of strip reinforced random composites (strip hybrids)

NASA Technical Reports Server (NTRS)

Chamis, C. C.; Sinclair, J. H.

1978-01-01

Advanced analysis methods and composite mechanics were applied to a strip-reinforced random composite square panel with fixed ends to illustrate the use of these methods for the a priori assessment of the composite panel when subjected to complex loading conditions. The panel was assumed to be of E-glass random composite. The strips were assumed to be of three advanced unidirectional composites to cover a range of low, intermediate, and high modulus stiffness. The panels were assumed to be subjected to complex loadings to assess their adequacy as load-carrying members in auto body, aircraft engine nacelle and windmill blade applications. The results show that strip hybrid panels can be several times more structurally efficient than the random composite base materials. Some of the results are presented in graphical form and procedures are described for use of these graphs as guides for preliminary design of strip hybrids.

Low and High Frequency Models of Response Statistics of a Cylindrical Orthogrid Vehicle Panel to Acoustic Excitation

NASA Technical Reports Server (NTRS)

Smith, Andrew; LaVerde, Bruce; Teague, David; Gardner, Bryce; Cotoni, Vincent

2010-01-01

This presentation further develops the orthogrid vehicle panel work. Employed Hybrid Module capabilities to assess both low/mid frequency and high frequency models in the VA One simulation environment. The response estimates from three modeling approaches are compared to ground test measurements. Detailed Finite Element Model of the Test Article -Expect to capture both the global panel modes and the local pocket mode response, but at a considerable analysis expense (time & resources). A Composite Layered Construction equivalent global stiffness approximation using SEA -Expect to capture response of the global panel modes only. An SEA approximation using the Periodic Subsystem Formulation. A finite element model of a single periodic cell is used to derive the vibroacoustic properties of the entire periodic structure (modal density, radiation efficiency, etc. Expect to capture response at various locations on the panel (on the skin and on the ribs) with less analysis expense

First external quality assurance program for bloodstream Real-Time PCR monitoring of treatment response in clinical trials of Chagas disease.

PubMed

Ramírez, Juan C; Parrado, Rudy; Sulleiro, Elena; de la Barra, Anabelle; Rodríguez, Marcelo; Villarroel, Sandro; Irazu, Lucía; Alonso-Vega, Cristina; Alves, Fabiana; Curto, María A; García, Lineth; Ortiz, Lourdes; Torrico, Faustino; Gascón, Joaquim; Flevaud, Laurence; Molina, Israel; Ribeiro, Isabela; Schijman, Alejandro G

2017-01-01

Real-Time PCR (qPCR) testing is recommended as both a diagnostic and outcome measurement of etiological treatment in clinical practice and clinical trials of Chagas disease (CD), but no external quality assurance (EQA) program provides performance assessment of the assays in use. We implemented an EQA system to evaluate the performance of molecular biology laboratories involved in qPCR based follow-up in clinical trials of CD. An EQA program was devised for three clinical trials of CD: the E1224 (NCT01489228), a pro-drug of ravuconazole; the Sampling Study (NCT01678599), that used benznidazole, both conducted in Bolivia; and the CHAGASAZOL (NCT01162967), that tested posaconazole, conducted in Spain. Four proficiency testing panels containing negative controls and seronegative blood samples spiked with 1, 10 and 100 parasite equivalents (par. eq.)/mL of four Trypanosoma cruzi stocks, were sent from the Core Lab in Argentina to the participating laboratories located in Bolivia and Spain. Panels were analyzed simultaneously, blinded to sample allocation, at 4-month intervals. In addition, 302 random blood samples from both trials carried out in Bolivia were sent to Core Lab for retesting analysis. The analysis of proficiency testing panels gave 100% of accordance (within laboratory agreement) and concordance (between laboratory agreement) for all T. cruzi stocks at 100 par. eq./mL; whereas their values ranged from 71 to 100% and from 62 to 100% at 1 and 10 par. eq./mL, respectively, depending on the T. cruzi stock. The results obtained after twelve months of preparation confirmed the stability of blood samples in guanidine-EDTA buffer. No significant differences were found between qPCR results from Bolivian laboratory and Core Lab for retested clinical samples. This EQA program for qPCR analysis of CD patient samples may significantly contribute to ensuring the quality of laboratory data generated in clinical trials and molecular diagnostics laboratories of CD.

Modeling vehicle operating speed on urban roads in Montreal: a panel mixed ordered probit fractional split model.

PubMed

Eluru, Naveen; Chakour, Vincent; Chamberlain, Morgan; Miranda-Moreno, Luis F

2013-10-01

Vehicle operating speed measured on roadways is a critical component for a host of analysis in the transportation field including transportation safety, traffic flow modeling, roadway geometric design, vehicle emissions modeling, and road user route decisions. The current research effort contributes to the literature on examining vehicle speed on urban roads methodologically and substantively. In terms of methodology, we formulate a new econometric model framework for examining speed profiles. The proposed model is an ordered response formulation of a fractional split model. The ordered nature of the speed variable allows us to propose an ordered variant of the fractional split model in the literature. The proposed formulation allows us to model the proportion of vehicles traveling in each speed interval for the entire segment of roadway. We extend the model to allow the influence of exogenous variables to vary across the population. Further, we develop a panel mixed version of the fractional split model to account for the influence of site-specific unobserved effects. The paper contributes substantively by estimating the proposed model using a unique dataset from Montreal consisting of weekly speed data (collected in hourly intervals) for about 50 local roads and 70 arterial roads. We estimate separate models for local roads and arterial roads. The model estimation exercise considers a whole host of variables including geometric design attributes, roadway attributes, traffic characteristics and environmental factors. The model results highlight the role of various street characteristics including number of lanes, presence of parking, presence of sidewalks, vertical grade, and bicycle route on vehicle speed proportions. The results also highlight the presence of site-specific unobserved effects influencing the speed distribution. The parameters from the modeling exercise are validated using a hold-out sample not considered for model estimation. The results indicate that the proposed panel mixed ordered probit fractional split model offers promise for modeling such proportional ordinal variables. Copyright © 2013 Elsevier Ltd. All rights reserved.

A Systematic Review and Meta-analysis of the Diagnostic Accuracy of Prostate Health Index and 4-Kallikrein Panel Score in Predicting Overall and High-grade Prostate Cancer.

PubMed

Russo, Giorgio Ivan; Regis, Federica; Castelli, Tommaso; Favilla, Vincenzo; Privitera, Salvatore; Giardina, Raimondo; Cimino, Sebastiano; Morgia, Giuseppe

2017-08-01

Markers for prostate cancer (PCa) have progressed over recent years. In particular, the prostate health index (PHI) and the 4-kallikrein (4K) panel have been demonstrated to improve the diagnosis of PCa. We aimed to review the diagnostic accuracy of PHI and the 4K panel for PCa detection. We performed a systematic literature search of PubMed, EMBASE, Cochrane, and Academic One File databases until July 2016. We included diagnostic accuracy studies that used PHI or 4K panel for the diagnosis of PCa or high-grade PCa. The methodological quality was assessed using the Quality Assessment of Diagnostic Accuracy Studies (QUADAS-2) tool. Twenty-eight studies including 16,762 patients have been included for the analysis. The pooled data showed a sensitivity of 0.89 and 0.74 for PHI and 4K panel, respectively, for PCa detection and a pooled specificity of 0.34 and 0.60 for PHI and 4K panel, respectively. The derived area under the curve (AUC) from the hierarchical summary receiver operating characteristic (HSROC) showed an accuracy of 0.76 and 0.72 for PHI and 4K panel respectively. For high-grade PCa detection, the pooled sensitivity was 0.93 and 0.87 for PHI and 4K panel, respectively, whereas the pooled specificity was 0.34 and 0.61 for PHI and 4K panel, respectively. The derived AUC from the HSROC showed an accuracy of 0.82 and 0.81 for PHI and 4K panel, respectively. Both PHI and the 4K panel provided good diagnostic accuracy in detecting overall and high-grade PCa. Copyright © 2016 Elsevier Inc. All rights reserved.

Multi-omics analysis reveals that ornithine decarboxylase contributes to erlotinib resistance in pancreatic cancer cells

PubMed Central

Song, Sang-Hoon; Lee, Naeun; Kim, Dong-Joon; Lee, Sooyeun; Jeong, Chul-Ho

2017-01-01

Molecular and metabolic alterations in cancer cells are one of the leading causes of acquired resistance to chemotherapeutics. In this study, we explored an experimental strategy to identify which of these alterations can induce erlotinib resistance in human pancreatic cancer. Using genetically matched erlotinib-sensitive (BxPC-3) and erlotinib-resistant (BxPC-3ER) pancreatic cancer cells, we conducted a multi-omics analysis of metabolomes and transcriptomes in these cells. Untargeted and targeted metabolomic analyses revealed significant changes in metabolic pathways involved in the regulation of polyamines, amino acids, and fatty acids. Further transcriptomic analysis identified that ornithine decarboxylase (ODC) and its major metabolite, putrescine, contribute to the acquisition of erlotinib resistance in BxPC-3ER cells. Notably, either pharmacological or genetic blockage of ODC was able to restore erlotinib sensitivity, and this could be rescued by treatment with exogenous putrescine in erlotinib-resistant BxPC-3ER cells. Moreover, using a panel of cancer cells we demonstrated that ODC expression levels in cancer cells are inversely correlated with sensitivity to chemotherapeutics. Taken together, our findings will begin to uncover mechanisms of acquired drug resistance and ultimately help to identify potential therapeutic markers in cancer. PMID:29190951

Analytical Prediction of Damage Growth in Notched Composite Panels Loaded in Axial Compression

NASA Technical Reports Server (NTRS)

Ambur, Damodar R.; McGowan, David M.; Davila, Carlos G.

1999-01-01

A progressive failure analysis method based on shell elements is developed for the computation of damage initiation and growth in stiffened thick-skin stitched graphite-epoxy panels loaded in axial compression. The analysis method involves a step-by-step simulation of material degradation based on ply-level failure mechanisms. High computational efficiency is derived from the use of superposed layers of shell elements to model each ply orientation in the laminate. Multiple integration points through the thickness are used to obtain the correct bending effects through the thickness without the need for ply-by-ply evaluations of the state of the material. The analysis results are compared with experimental results for three stiffened panels with notches oriented at 0, 15 and 30 degrees to the panel width dimension. A parametric study is performed to investigate the damage growth retardation characteristics of the Kevlar stitch lines in the pan

Coupling of the Inner Magnetosphere with the Underlying Atmosphere and Ionosphere

NASA Technical Reports Server (NTRS)

Sharber, James M. (Technical Monitor); Kozyra, Janet

2005-01-01

The following is a final report summarizing our very successful inner magnetosphere research program through which we have made significant contributions to: (1) research through data analysis, modeling and participation in community-wide campaigns, (2) the development of the space science discipline through leadership in national and international campaigns, service on steering committees, review panels and the development and maintenance of campaign and community web sites, (3) education and human resources by the participation of graduate, undergraduate and high school students in our research programs and (4) outreach through development of web-based materials and interactive games. We describe each of these activities below.

Do More of Those in Misery Suffer from Poverty, Unemployment or Mental Illness?

PubMed Central

Flèche, Sarah

2017-01-01

SUMMARY Studies of deprivation usually ignore mental illness. This paper uses household panel data from the USA, Australia, Britain and Germany to broaden the analysis. We ask first how many of those in the lowest levels of life-satisfaction suffer from unemployment, poverty, physical ill health, and mental illness. The largest proportion suffers from mental illness. Multiple regression shows that mental illness is not highly correlated with poverty or unemployment, and that it contributes more to explaining the presence of misery than is explained by either poverty or unemployment. This holds both with and without fixed effects. PMID:28729747

Gender role attitudes, relationship efficacy, and self-disclosure in intimate relationships.

PubMed

Horne, Rebecca M; Johnson, Matthew D

2018-01-01

Drawing from the intimacy process model and data from 5,042 individuals who remained partnered across Waves 1 and 2 of the German Panel Analysis of Intimate Relationships and Family Dynamics (pairfam), this study examined the contributions of traditional gender role attitudes and relationship efficacy in predicting levels of self-disclosure within an intimate relationship. Independent samples t-tests demonstrated females scored higher than males on self-disclosure and relationship efficacy measures but lower on traditional gender role attitudes. An ordinary least squares regression analysis revealed relationship efficacy was a stronger predictor of self-disclosure compared to traditional gender role attitudes, which were not associated with self-disclosure. The findings suggest attitudes with an interpersonal motivational system may be especially important for setting the intimacy process into motion within an intimate union.

Improved recognition of figures containing fluorescence microscope images in online journal articles using graphical models.

PubMed

Qian, Yuntao; Murphy, Robert F

2008-02-15

There is extensive interest in automating the collection, organization and analysis of biological data. Data in the form of images in online literature present special challenges for such efforts. The first steps in understanding the contents of a figure are decomposing it into panels and determining the type of each panel. In biological literature, panel types include many kinds of images collected by different techniques, such as photographs of gels or images from microscopes. We have previously described the SLIF system (http://slif.cbi.cmu.edu) that identifies panels containing fluorescence microscope images among figures in online journal articles as a prelude to further analysis of the subcellular patterns in such images. This system contains a pretrained classifier that uses image features to assign a type (class) to each separate panel. However, the types of panels in a figure are often correlated, so that we can consider the class of a panel to be dependent not only on its own features but also on the types of the other panels in a figure. In this article, we introduce the use of a type of probabilistic graphical model, a factor graph, to represent the structured information about the images in a figure, and permit more robust and accurate inference about their types. We obtain significant improvement over results for considering panels separately. The code and data used for the experiments described here are available from http://murphylab.web.cmu.edu/software.

The More or the Better? How Sex Contributes to Life Satisfaction.

PubMed

Schmiedeberg, Claudia; Huyer-May, Bernadette; Castiglioni, Laura; Johnson, Matthew D

2017-02-01

Much cross-sectional research documented associations between sexuality and life satisfaction, but very little longitudinal research on the topic has considered whether changes in sexuality and life satisfaction unfold together over time. Using data from 5582 individuals in partnerships surveyed across 5786 intimate relationships (providing 18,712 observations for analysis) during five waves of the German Family Panel (pairfam), this study examined whether intraindividual changes in sexual frequency and satisfaction were associated with corresponding intraindividual changes in life satisfaction. Fixed effects regression modeling results showed that individuals reported a greater increase (decrease) in life satisfaction when they also experienced a more substantial increase (decrease) in sexual frequency and satisfaction. This finding was consistent for men and women. This study contributes to the literature by documenting that naturally occurring increases in sexual frequency and satisfaction over time predicted corresponding increases in life satisfaction.

Buckling of a Longitudinally Jointed Curved Composite Panel Arc Segment for Next Generation of Composite Heavy Lift Launch Vehicles: Verification Testing Analysis

NASA Technical Reports Server (NTRS)

Farrokh, Babak; Segal, Kenneth N.; Akkerman, Michael; Glenn, Ronald L.; Rodini, Benjamin T.; Fan, Wei-Ming; Kellas, Sortiris; Pineda, Evan J.

2014-01-01

In this work, an all-bonded out-of-autoclave (OoA) curved longitudinal composite joint concept, intended for use in the next generation of composite heavy lift launch vehicles, was evaluated and verified through finite element (FE) analysis, fabrication, testing, and post-test inspection. The joint was used to connect two curved, segmented, honeycomb sandwich panels representative of a Space Launch System (SLS) fairing design. The overall size of the resultant panel was 1.37 m by 0.74 m (54 in by 29 in), of which the joint comprised a 10.2 cm (4 in) wide longitudinal strip at the center. NASTRAN and ABAQUS were used to perform linear and non-linear analyses of the buckling and strength performance of the jointed panel. Geometric non-uniformities (i.e., surface contour imperfections) were measured and incorporated into the FE model and analysis. In addition, a sensitivity study of the specimens end condition showed that bonding face-sheet doublers to the panel's end, coupled with some stress relief features at corner-edges, can significantly reduce the stress concentrations near the load application points. Ultimately, the jointed panel was subjected to a compressive load. Load application was interrupted at the onset of buckling (at 356 kN 80 kips). A post-test non-destructive evaluation (NDE) showed that, as designed, buckling occurred without introducing any damage into the panel or the joint. The jointed panel was further capable of tolerating an impact damage to the same buckling load with no evidence of damage propagation. The OoA cured all-composite joint shows promise as a low mass factory joint for segmented barrels.

A general panel sizing computer code and its application to composite structural panels

NASA Technical Reports Server (NTRS)

Anderson, M. S.; Stroud, W. J.

1978-01-01

A computer code for obtaining the dimensions of optimum (least mass) stiffened composite structural panels is described. The procedure, which is based on nonlinear mathematical programming and a rigorous buckling analysis, is applicable to general cross sections under general loading conditions causing buckling. A simplified method of accounting for bow-type imperfections is also included. Design studies in the form of structural efficiency charts for axial compression loading are made with the code for blade and hat stiffened panels. The effects on panel mass of imperfections, material strength limitations, and panel stiffness requirements are also examined. Comparisons with previously published experimental data show that accounting for imperfections improves correlation between theory and experiment.

Linear Strength Vortex Panel Method for NACA 4412 Airfoil

NASA Astrophysics Data System (ADS)

Liu, Han

2018-03-01

The objective of this article is to formulate numerical models for two-dimensional potential flow over the NACA 4412 Airfoil using linear vortex panel methods. By satisfying the no penetration boundary condition and Kutta condition, the circulation density on each boundary points (end point of every panel) are obtained and according to which, surface pressure distribution and lift coefficients of the airfoil are predicted and validated by Xfoil, an interactive program for the design and analysis of airfoil. The sensitivity of results to the number of panels is also investigated in the end, which shows that the results are sensitive to the number of panels when panel number ranges from 10 to 160. With the increasing panel number (N>160), the results become relatively insensitive to it.

Spectroscopic characterization of sixteenth century panel painting references using Raman, surface-enhanced Raman spectroscopy and helium-Raman system for in situ analysis of Ibero-American Colonial paintings

PubMed Central

2016-01-01

Colonial panel paintings constitute an essential part of Latin-American cultural heritage. Their study is vital for understanding the manufacturing process, including its evolution in history, as well as its authorship, dating and other information significant to art history and conservation purposes. Raman spectroscopy supplies a non-destructive characterization tool, which can be implemented for in situ analysis, via portable equipment. Specific methodologies must be developed, comprising the elaboration of reference panel paintings using techniques and materials similar to those of the analysed period, as well as the determination of the best analysis conditions for different pigments and ground preparations. In order to do so, Raman spectroscopy at 532, 785 and 1064 nm, surface-enhanced Raman spectroscopy (SERS) and a helium-Raman system were applied to a panel painting reference, in combination with X-ray fluorescence analysis. We were able to establish the analysis conditions for a number of sixteenth century pigments and dyes, and other relevant components of panel paintings from this period, 1064 nm Raman and SERS being the most successful. The acquired spectra contain valuable specific information for their identification and they conform a very useful database that can be applied to the analysis of Ibero-American Colonial paintings. This article is part of the themed issue ‘Raman spectroscopy in art and archaeology’. PMID:27799434

Wing Leading Edge Debris Analysis

NASA Technical Reports Server (NTRS)

Shah, Sandeep; Jerman, Gregory

2004-01-01

This is a slide presentation showing the Left Wing Leading Edge (WLE) heat damage observations: Heavy "slag" deposits on select RCC panels. Eroded and knife-edged RCC rib sections. Excessive overheating and slumping of carrier panel tiles. Missing or molten attachment bolts but intact bushing. Deposit mainly on "inside" RCC panel. Deposit on some fractured RCC surface

EDRN Breast and Ovary Cancer CVC, Study 2: Phase 3 retrospective validation of ovarian cancer early detection markers in serial preclinical samples from the PLCO trial — EDRN Public Portal

Cancer.gov

Over 70% of women with ovarian/fallopian tube cancer (OC) are diagnosed with advanced stage disease which has a 5-year relative survival rate of 30%. Five-year survival is 90% when disease is confined to the ovaries, but overall survival is poor because only 25% of cases are found early. Screening for ovarian cancer using tools with high sensitivity is potentially cost-effective, but because OC is so rare, very high specificity is needed to achieve an acceptable PPV. We have conducted preliminary work both in clinical and in preclinical (CARET) samples. We have identified candidate markers, developed assays for novel markers including HE4 and MSLN, and evaluated their diagnostic performance. We evaluated the markers’ contribution to a diagnostic panel in a standard set in order to identify the best of the candidates and developed methods for combining markers to define a decision rule for a marker panel. We found that our PEB rule yields comparable performance to the Single Threshold (ST) rule 2 years earlier, using the same two markers. The PEB makes an even larger contribution with the 4-marker panel. The 4-marker panel with the PEB rule represents a substantial improvement over any of the other decision rules as a first-line screen to select women for imaging. Our goal in the proposed work is to estimate the improvement in performance possible in the PLCO serial samples.

Infrared Multispectral Sensor Program, Phase 2. Field Measurements, Analysis and Modeling. Volume 1. Fourier Transform Spectrometer Sensor Characterization.

DTIC Science & Technology

1994-05-01

TskY=250K) ... 5-27 6-1. Treeline Correlation With 10.1 Microns ...................... 6-2 6-2. Mean Contrast: CARC Panel vs. Treeline ...6-3 6-3. CARC Panel and Treeline .............................. 6-5 6-4. Signal-to-Clutter Ratio for CARC Panel vs. Treeline ............. 6-6 6...5. Low Emissivity Panel and Treeline ......................... 6-7 xii TABLES 4-1: Sensor Characterization Test Summary ....................... 4-2 4

Prediction and Measurement of the Vibration and Acoustic Radiation of Panels Subjected to Acoustic Loading

NASA Technical Reports Server (NTRS)

Turner, Travis L.; Rizzi, Stephen A.

1995-01-01

Interior noise and sonic fatigue are important issues in the development and design of advanced subsonic and supersonic aircraft. Conventional aircraft typically employ passive treatments, such as constrained layer damping and acoustic absorption materials, to reduce the structural response and resulting acoustic levels in the aircraft interior. These techniques require significant addition of mass and only attenuate relatively high frequency noise transmitted through the fuselage. Although structural acoustic coupling is in general very important in the study of aircraft fuselage interior noise, analysis of noise transmission through a panel supported in an infinite rigid baffle (separating two semi-infinite acoustic domains) can be useful in evaluating the effects of active/adaptive materials, complex loading, etc. Recent work has been aimed at developing adaptive and/or active methods of controlling the structural acoustic response of panels to reduce the transmitted noise1. A finite element formulation was recently developed to study the dynamic response of shape memory alloy (SMA) hybrid composite panels (conventional composite panel with embedded SMA fibers) subject to combined acoustic and thermal loads2. Further analysis has been performed to predict the far-field acoustic radiation using the finite element dynamic panel response prediction3. The purpose of the present work is to validate the panel vibration and acoustic radiation prediction methods with baseline experimental results obtained from an isotropic panel, without the effect of SMA.

Mathematical Creativity and Mathematical Aptitude: A Cross-Lagged Panel Analysis

ERIC Educational Resources Information Center

Tyagi, Tarun Kumar

2016-01-01

Cross-lagged panel correlation (CLPC) analysis has been used to identify causal relationships between mathematical creativity and mathematical aptitude. For this study, 480 8th standard students were selected through a random cluster technique from 9 intermediate and high schools of Varanasi, India. Mathematical creativity and mathematical…

DNA Hypermethylation Patterns Detected in Serum as a Tool for Early Breast Cancer Diagnosis

DTIC Science & Technology

2008-09-01

age at, and date of, blood donation. The analysis of the promoter methylation status of a panel of six cancer- related genes (RASSF1A, GSTP1 , RARβ2...Gene Selection: As reported in the previous progress report, the gene panel was modified to include: RASSF1A, HIN-1, GSTP1 , APC, p16 and RARβ2...gene was removed from the panel (for the time being) and analysis of RASSF1A, GSTP1 , RARβ2 and APC conducted. QMSP Results: Assays have been

SLB-STO-D ANALYSIS REPORT: MODELING AND SIMULATION ANALYSIS OF FUEL, WATER, AND WASTE REDUCTIONS IN BASE CAMPS: 50, 300, AND 1000 PERSONS

DTIC Science & Technology

2017-08-21

panels only produce power when the sun is out, turbines only produce power when there xiii is wind , etc. For these sources to be fully utilized...hybrid energy system mounted on a towable trailer consisting of an onboard diesel generator, solar panels, wind turbines , and an energy storage...limited to certain times of day—solar panels only produce power when the sun is out, turbines only produce power when there is wind , etc. For these

Subtyping of Canadian isolates of Salmonella Enteritidis using Multiple Locus Variable Number Tandem Repeat Analysis (MLVA) alone and in combination with Pulsed-Field Gel Electrophoresis (PFGE) and phage typing.

PubMed

Ziebell, Kim; Chui, Linda; King, Robin; Johnson, Suzanne; Boerlin, Patrick; Johnson, Roger P

2017-08-01

Salmonella enterica subspecies enterica serovar Enteritidis (SE) is one of the most common causes of human salmonellosis and in Canada currently accounts for over 40% of human cases. Reliable subtyping of isolates is required for outbreak detection and source attribution. However, Pulsed-Field Gel Electrophoresis (PFGE), the current standard subtyping method for Salmonella spp., is compromised by the high genetic homogeneity of SE. Multiple Locus Variable Number Tandem Repeat Analysis (MLVA) was introduced to supplement PFGE, although there is a lack of data on the ability of MLVA to subtype Canadian isolates of SE. Three subtyping methods, PFGE, MLVA and phage typing were compared for their discriminatory power when applied to three panels of Canadian SE isolates: Panel 1: 70 isolates representing the diversity of phage types (PTs) and PFGE subtypes within these PTs; Panel 2: 214 apparently unrelated SE isolates of the most common PTs; and Panel 3: 27 isolates from 10 groups of epidemiologically related strains. For Panel 2 isolates, four MLVA subtypes were shared among 74% of unrelated isolates and in Panel 3 isolates, one MLVA subtype accounted for 62% of the isolates. For all panels, combining results from PFGE, MLVA and PT gave the best discrimination, except in Panel 1, where the combination of PT and PFGE was equally as high, due to the selection criteria for this panel. However, none of these methods is sufficiently discriminatory alone for reliable outbreak detection or source attribution, and must be applied together to achieve sufficient discrimination for practical purposes. Even then, some large clusters were not differentiated adequately. More discriminatory methods are required for reliable subtyping of this genetically highly homogeneous serovar. This need will likely be met by whole genome sequence analysis given the recent promising reports and as more laboratories implement this tool for outbreak response and surveillance. Copyright © 2017 Elsevier B.V. All rights reserved.

Taste characteristics of Chinese bayberry juice characterized by sensory evaluation, chromatography analysis, and an electronic tongue.

PubMed

Yu, Haiyan; Zhang, Yan; Zhao, Jie; Tian, Huaixiang

2018-05-01

To evaluate the taste characteristics of Chinese bayberry juice, four types of bayberry juice sourced from different origins and varieties were analysed using sensory evaluation, chromatography, spectroscopy analysis and an electronic tongue (E-tongue). Nine organic acids and three sugars were assessed using high performance liquid chromatography. Total polyphenols were measured by spectrophotometry. The overall taste profile was collected using the E-tongue. The four types of bayberry juice differed in the sensory attributes of sour, sweet, bitter, and astringent. The E-tongue responses combined with discriminant analysis were able to characterise the taste profiles of the juices. The relationships between the taste compounds and the sensory panel scores established by partial least squares showed that total polyphenols, quininic acid, maleic acid, fructose, citric acid, lactic acid, succinic acid and sucrose made significant contributions to the taste characteristics of the Chinese bayberry juice.

Different contributions of internal reviewers and external experts to labelling decisions on therapeutic indications in new drug reviews in Japan.

PubMed

Yokota, M; Kusama, M; Matsuki, N; Ono, S

2013-12-01

External experts play an important role in shaping regulatory decisions in the new drug review process in the United States, Europe and Japan. No rigorous study has been performed addressing how and to what extent external experts, in contrast to internal reviewers in the agency, influence the regulatory decisions during new drug reviews. We examined their contributions in Japanese regulatory reviews in contrast to the internal reviewers, focusing on the labelling decision on therapeutic indications. With the data set of 219 new molecular entities (NMEs) approved in Japan from 2000 to 2009, we observed how proposed indications in labelling were modified in a stepwise manner during the review process and conducted multinomial logistic analysis to examine the possible mechanism behind. We found that interim assessment of indications by the internal reviewers was modified substantially by the influence of the external experts in about 20% of the 219 NMEs. Our analysis suggested that internal reviewers provided their opinion mainly based on strict review discipline, whereas external experts added flexibility and reality to their reviews. Our analysis revealed different evaluations between internal reviewers and external experts during regulatory discussions in new drug reviews and how the external panel contributes to changing internal decisions. This study provides a new and quantitative approach to better label setting by emphasizing the contributions of each stakeholder in new drug reviews, which would improve the efficiency, quality and transparency of new drug reviews to enhance public health. © 2013 John Wiley & Sons Ltd.

The Flint Animal Cancer Center (FACC) Canine Tumour Cell Line Panel: a resource for veterinary drug discovery, comparative oncology and translational medicine.

PubMed

Fowles, J S; Dailey, D D; Gustafson, D L; Thamm, D H; Duval, D L

2017-06-01

Mammalian cell tissue culture has been a critical tool leading to our current understanding of cancer including many aspects of cellular transformation, growth and response to therapies. The current use of large panels of cell lines with associated phenotypic and genotypic information now allows for informatics approaches and in silico screens to rapidly test hypotheses based on simple as well as complex relationships. Current cell line panels with large amounts of associated drug sensitivity and genomics data are comprised of human cancer cell lines (i.e. NCI60 and GDSC). There is increased recognition of the contribution of canine cancer to comparative cancer research as a spontaneous large animal model with application in basic and translational studies. We have assembled a panel of canine cancer cell lines to facilitate studies in canine cancer and report here phenotypic and genotypic data associated with these cells. © 2016 John Wiley & Sons Ltd.

Buckling Testing and Analysis of Honeycomb Sandwich Panel Arc Segments of a Full-Scale Fairing Barrel Part 1: 8-Ply In-Autoclave Facesheets. Part 1; 8-Ply In-Autoclave Facesheets

NASA Technical Reports Server (NTRS)

Myers, David E.; Pineda, Evan J.; Zalewski, Bart F.; Kosareo, Daniel N.; Kellas, Sotiris

2013-01-01

Four honeycomb sandwich panels, representing 1/16th arc segments of a 10-m diameter barrel section of the heavy lift launch vehicle, were manufactured under the NASA Composites for Exploration program and the NASA Space Launch Systems program. Two configurations were chosen for the panels: 6-ply facesheets with 1.125 in. honeycomb core and 8-ply facesheets with 1.000 in. honeycomb core. Additionally, two separate carbon fiber/epoxy material systems were chosen for the facesheets: inautoclave IM7/977-3 and out-of-autoclave T40-800b/5320-1. Smaller 3.00- by 5.00-ft panels were cut from the 1/16th barrel sections. These panels were tested under compressive loading at the NASA Langley Research Center. Furthermore, linear eigenvalue and geometrically nonlinear finite element analysis was performed to predict the compressive response of the 3.00- by 5.00-ft panels. This manuscript summarizes the experimental and analytical modeling efforts pertaining to the panel composed of 8-ply, IM7/977-3 facesheets (referred to Panel A). To improve the robustness of the geometrically nonlinear finite element model, measured surface imperfections were included in the geometry of the model. Both the linear and nonlinear models yield good qualitative and quantitative predictions. Additionally, it was predicted correctly that the panel would fail in buckling prior to failing in strength. Furthermore, several imperfection studies were performed to investigate the influence of geometric imperfections, fiber misalignments, and three-dimensional (3 D) effects on the compressive response of the panel.

Study of advanced composite structural design concepts for an arrow wing supersonic cruise configuration, task 3

NASA Technical Reports Server (NTRS)

1978-01-01

A structural design study was conducted to assess the relative merits of structural concepts using advanced composite materials for an advanced supersonic aircraft cruising at Mach 2.7. The configuration and structural arrangement developed during Task I and II of the study, was used as the baseline configuration. Allowable stresses and strains were established for boron and advanced graphite fibers based on projected fiber properties available in the next decade. Structural concepts were designed and analyzed using graphite polyimide and boron polyimide, applied to stiffened panels and conventional sandwich panels. The conventional sandwich panels were selected as the structural concept to be used on the wing structure. The upper and lower surface panels of the Task I arrow wing were redesigned using high-strength graphite polyimide sandwich panels over the titanium spars and ribs. The ATLAS computer system was used as the basis for stress analysis and resizing the surface panels using the loads from the Task II study, without adjustment for change in aeroelastic deformation. The flutter analysis indicated a decrease in the flutter speed compared to the baseline titanium wing design. The flutter analysis indicated a decrease in the flutter speed compared to the baseline titanium wing design. The flutter speed was increased to that of the titanium wing, with a weight penalty less than that of the metallic airplane.

Tensile strength of composite sheets with unidirectional stringers and crack-like damage

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.

1984-01-01

The damage tolerance characteristics of metal tension panels with riveted and bonded stringers are well known. The stringers arrest unstable cracks and retard propagation of fatigue cracks. Residual strengths and fatigue lives are considerably greater than those of unstiffened or integrally stiffened sheets. The damage tolerance of composite sheets with bonded composite stringers loaded in tension was determined. Cracks in composites do not readily propagate in fatigue, at least not through fibers. Moreover, the residual strength of notched composites is sometimes even increased by fatigue loading. Therefore, the residual strength aspect of damage tolerance, and not fatigue crack propagation, was investigated. About 50 graphite/epoxy composite panels were made with two sheet layups and several stringer configurations. Crack-like slots were cut in the middle of the panels to simulate damage. The panels were instrumented and monotonically loaded in tension to failure. The tests indicate that the composite panels have considerable damage tolerance, much like metal panels. The stringers arrested cracks that ran from the crack-like slots, and the residual strengths were considerably greater than those of unstiffened composite sheets. A stress intensity factor analysis was developed to predict the failing strains of the stiffened panels. Using the analysis, a single design curve was produced for composite sheets with bonded stringers of any configuration.

Optimization of Blended Wing Body Composite Panels Using Both NASTRAN and Genetic Algorithm

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.

2006-01-01

The blended wing body (BWB) is a concept that has been investigated for improving the performance of transport aircraft. A trade study was conducted by evaluating four regions from a BWB design characterized by three fuselage bays and a 400,000 lb. gross take-off weight (GTW). This report describes the structural optimization of these regions via computational analysis and compares them to the baseline designs of the same construction. The identified regions were simplified for use in the optimization. The regions were represented by flat panels having appropriate classical boundary conditions and uniform force resultants along the panel edges. Panel-edge tractions and internal pressure values applied during the study were those determined by nonlinear NASTRAN analyses. Only one load case was considered in the optimization analysis for each panel region. Optimization was accomplished using both NASTRAN solution 200 and Genetic Algorithm (GA), with constraints imposed on stress, buckling, and minimum thicknesses. The NASTRAN optimization analyses often resulted in infeasible solutions due to violation of the constraints, whereas the GA enforced satisfaction of the constraints and, therefore, always ensured a feasible solution. However, both optimization methods encountered difficulties when the number of design variables was increased. In general, the optimized panels weighed less than the comparable baseline panels.

Compression After Impact on Honeycomb Core Sandwich Panels with Thin Facesheets, Part 2: Analysis

NASA Technical Reports Server (NTRS)

Mcquigg, Thomas D.; Kapania, Rakesh K.; Scotti, Stephen J.; Walker, Sandra P.

2012-01-01

A two part research study has been completed on the topic of compression after impact (CAI) of thin facesheet honeycomb core sandwich panels. The research has focused on both experiments and analysis in an effort to establish and validate a new understanding of the damage tolerance of these materials. Part 2, the subject of the current paper, is focused on the analysis, which corresponds to the CAI testings described in Part 1. Of interest, are sandwich panels, with aerospace applications, which consist of very thin, woven S2-fiberglass (with MTM45-1 epoxy) facesheets adhered to a Nomex honeycomb core. Two sets of materials, which were identical with the exception of the density of the honeycomb core, were tested in Part 1. The results highlighted the need for analysis methods which taken into account multiple failure modes. A finite element model (FEM) is developed here, in Part 2. A commercial implementation of the Multicontinuum Failure Theory (MCT) for progressive failure analysis (PFA) in composite laminates, Helius:MCT, is included in this model. The inclusion of PFA in the present model provided a new, unique ability to account for multiple failure modes. In addition, significant impact damage detail is included in the model. A sensitivity study, used to assess the effect of each damage parameter on overall analysis results, is included in an appendix. Analysis results are compared to the experimental results for each of the 32 CAI sandwich panel specimens tested to failure. The failure of each specimen is predicted using the high-fidelity, physicsbased analysis model developed here, and the results highlight key improvements in the understanding of honeycomb core sandwich panel CAI failure. Finally, a parametric study highlights the strength benefits compared to mass penalty for various core densities.

Design of hat-stiffened composite panels loaded in axial compression

NASA Astrophysics Data System (ADS)

Paul, T. K.; Sinha, P. K.

An integrated step-by-step analysis procedure for the design of axially compressed stiffened composite panels is outlined. The analysis makes use of the effective width concept. A computer code, BUSTCOP, is developed incorporating various aspects of buckling such as skin buckling, stiffener crippling and column buckling. Other salient features of the computer code include capabilities for generation of data based on micromechanics theories and hygrothermal analysis, and for prediction of strength failure. Parametric studies carried out on a hat-stiffened structural element indicate that, for all practical purposes, composite panels exhibit higher structural efficiency. Some hybrid laminates with outer layers made of aluminum alloy also show great promise for flight vehicle structural applications.

NASA/DOE/DOD nuclear propulsion technology planning: Summary of FY 1991 interagency panel results

NASA Technical Reports Server (NTRS)

Clark, John S.; Wickenheiser, Timothy J.; Doherty, Michael P.; Marshall, Albert; Bhattacharryya, Samit K.; Warren, John

1992-01-01

Interagency (NASA/DOE/DOD) technical panels worked in 1991 to evaluate critical nuclear propulsion issues, compare nuclear propulsion concepts for a manned Mars mission on a consistent basis, and to continue planning a technology development project for the Space Exploration Initiative (SEI). Panels were formed to address mission analysis, nuclear facilities, safety policy, nuclear fuels and materials, nuclear electric propulsion technology, and nuclear thermal propulsion technology. A summary of the results and recommendations of the panels is presented.

Stresses in acoustically excited panels and shuttle insulation tiles

NASA Technical Reports Server (NTRS)

Otalvo, I. U.

1976-01-01

Natural vibration and acoustic response results are presented for a 36 x 18 inch panel with 18 6 x 6-inch tiles of 1.0, 1.6 and 2.3 inch thicknesses. Computed results for an untiled panel are compared with experiments performed earlier. Natural frequency and acoustic response comparisons are also given for independent analyses performed upon tiled and untiled panels. The results indicate the general applicability of the computer programs developed for use as shuttle design and analysis tools.

Analysis of the Final Report of the Fundamental Science Review: A Blueprint for Research, A Call for Action

ERIC Educational Resources Information Center

Canadian Association of University Teachers, 2017

2017-01-01

Canadian Association of University Teachers (CAUT) welcomes the report of the Advisory Panel on Federal Support for Fundamental Science "the Panel". It is a thoughtful and comprehensive study that correctly diagnoses problems that have plagued basic science for over a decade. The Panel's recommendations, if implemented, will chart a…

Damage Tolerant Analysis of Cracked Al 2024-T3 Panels repaired with Single Boron/Epoxy Patch

NASA Astrophysics Data System (ADS)

Mahajan, Akshay D.; Murthy, A. Ramachandra; Nanda Kumar, M. R.; Gopinath, Smitha

2018-06-01

It is known that damage tolerant analysis has two objectives, namely, remaining life prediction and residual strength evaluation. To achieve the these objectives, determination of accurate and reliable fracture parameter is very important. XFEM methodologies for fatigue and fracture analysis of cracked aluminium panels repaired with different patch shapes made of single boron/epoxy have been developed. Heaviside and asymptotic crack tip enrichment functions are employed to model the crack. XFEM formulations such as displacement field formulation and element stiffness matrix formulation are presented. Domain form of interaction integral is employed to determine Stress Intensity Factor of repaired cracked panels. Computed SIFs are incorporated in Paris crack growth model to predict the remaining fatigue life. The residual strength has been computed by using the remaining life approach, which accounts for both crack growth constants and no. of cycles to failure. From the various studies conducted, it is observed that repaired panels have significant effect on reduction of the SIF at the crack tip and hence residual strength as well as remaining life of the patched cracked panels are improved significantly. The predicted remaining life and residual strength will be useful for design of structures/components under fatigue loading.

A metabolomics approach to the identification of biomarkers of sugar-sweetened beverage intake.

PubMed

Gibbons, Helena; McNulty, Breige A; Nugent, Anne P; Walton, Janette; Flynn, Albert; Gibney, Michael J; Brennan, Lorraine

2015-03-01

The association between sugar-sweetened beverages (SSBs) and health risks remains controversial. To clarify proposed links, reliable and accurate dietary assessment methods of food intakes are essential. The aim of this present work was to use a metabolomics approach to identify a panel of urinary biomarkers indicative of SSB consumption from a national food consumption survey and subsequently validate this panel in an acute intervention study. Heat map analysis was performed to identify correlations between ¹H nuclear magnetic resonance (NMR) spectral regions and SSB intakes in participants of the National Adult Nutrition Survey (n = 565). Metabolites were identified and receiver operating characteristic (ROC) analysis was performed to assess sensitivity and specificity of biomarkers. The panel of biomarkers was validated in an acute study (n = 10). A fasting first-void urine sample and postprandial samples (2, 4, 6 h) were collected after SSB consumption. After NMR spectroscopic profiling of the urine samples, multivariate data analysis was applied. A panel of 4 biomarkers-formate, citrulline, taurine, and isocitrate-were identified as markers of SSB intake. This panel of biomarkers had an area under the curve of 0.8 for ROC analysis and a sensitivity and specificity of 0.7 and 0.8, respectively. All 4 biomarkers were identified in the SSB sample. After acute consumption of an SSB drink, all 4 metabolites increased in the urine. The present metabolomics-based strategy proved to be successful in the identification of SSB biomarkers. Future work will ascertain how to translate this panel of markers for use in nutrition epidemiology. © 2015 American Society for Nutrition.

Experimental and Theoretical Modal Analysis of Full-Sized Wood Composite Panels Supported on Four Nodes

PubMed Central

Guan, Cheng; Zhang, Houjiang; Wang, Xiping; Miao, Hu; Zhou, Lujing; Liu, Fenglu

2017-01-01

Key elastic properties of full-sized wood composite panels (WCPs) must be accurately determined not only for safety, but also serviceability demands. In this study, the modal parameters of full-sized WCPs supported on four nodes were analyzed for determining the modulus of elasticity (E) in both major and minor axes, as well as the in-plane shear modulus of panels by using a vibration testing method. The experimental modal analysis was conducted on three full-sized medium-density fiberboard (MDF) and three full-sized particleboard (PB) panels of three different thicknesses (12, 15, and 18 mm). The natural frequencies and mode shapes of the first nine modes of vibration were determined. Results from experimental modal testing were compared with the results of a theoretical modal analysis. A sensitivity analysis was performed to identify the sensitive modes for calculating E (major axis: Ex and minor axis: Ey) and the in-plane shear modulus (Gxy) of the panels. Mode shapes of the MDF and PB panels obtained from modal testing are in a good agreement with those from theoretical modal analyses. A strong linear relationship exists between the measured natural frequencies and the calculated frequencies. The frequencies of modes (2, 0), (0, 2), and (2, 1) under the four-node support condition were determined as the characteristic frequencies for calculation of Ex, Ey, and Gxy of full-sized WCPs. The results of this study indicate that the four-node support can be used in free vibration test to determine the elastic properties of full-sized WCPs. PMID:28773043

Reliability of stiffened structural panels: Two examples

NASA Technical Reports Server (NTRS)

Stroud, W. Jefferson; Davis, D. Dale, Jr.; Maring, Lise D.; Krishnamurthy, Thiagaraja; Elishakoff, Isaac

1992-01-01

The reliability of two graphite-epoxy stiffened panels that contain uncertainties is examined. For one panel, the effect of an overall bow-type initial imperfection is studied. The size of the bow is assumed to be a random variable. The failure mode is buckling. The benefits of quality control are explored by using truncated distributions. For the other panel, the effect of uncertainties in a strain-based failure criterion is studied. The allowable strains are assumed to be random variables. A geometrically nonlinear analysis is used to calculate a detailed strain distribution near an elliptical access hole in a wing panel that was tested to failure. Calculated strains are used to predict failure. Results are compared with the experimental failure load of the panel.

Use of Internet panels to conduct surveys.

PubMed

Hays, Ron D; Liu, Honghu; Kapteyn, Arie

2015-09-01

The use of Internet panels to collect survey data is increasing because it is cost-effective, enables access to large and diverse samples quickly, takes less time than traditional methods to obtain data for analysis, and the standardization of the data collection process makes studies easy to replicate. A variety of probability-based panels have been created, including Telepanel/CentERpanel, Knowledge Networks (now GFK KnowledgePanel), the American Life Panel, the Longitudinal Internet Studies for the Social Sciences panel, and the Understanding America Study panel. Despite the advantage of having a known denominator (sampling frame), the probability-based Internet panels often have low recruitment participation rates, and some have argued that there is little practical difference between opting out of a probability sample and opting into a nonprobability (convenience) Internet panel. This article provides an overview of both probability-based and convenience panels, discussing potential benefits and cautions for each method, and summarizing the approaches used to weight panel respondents in order to better represent the underlying population. Challenges of using Internet panel data are discussed, including false answers, careless responses, giving the same answer repeatedly, getting multiple surveys from the same respondent, and panelists being members of multiple panels. More is to be learned about Internet panels generally and about Web-based data collection, as well as how to evaluate data collected using mobile devices and social-media platforms.

Basic metabolic panel

MedlinePlus

SMAC7; Sequential multi-channel analysis with computer-7; SMA7; Metabolic panel 7; CHEM-7 ... breathing problems, diabetes or diabetes-related complications, and medicine side effects. Talk to your provider about the ...

In-Flight Laboratory Analysis

NASA Technical Reports Server (NTRS)

Baumann, David; Perusek, Gail; Nelson, Emily; Krihak, Michael; Brown, Dan

2012-01-01

One-year study objectives align with HRP requirements. HRP requirements include measurement panels for research and medical operations - These measurement panels are distinctly different. Instrument requirements are defined - Power, volume and mass not quite a critical limitation as for medical operations (deep space exploration missions). One-year evaluation goals will lead HHC towards in-flight laboratory analysis capability.

School Connectedness and Chinese Adolescents' Sleep Problems: A Cross-Lagged Panel Analysis

ERIC Educational Resources Information Center

Bao, Zhenzhou; Chen, Chuansheng; Zhang, Wei; Jiang, Yanping; Zhu, Jianjun; Lai, Xuefen

2018-01-01

Background: Although previous research indicates an association between school connectedness and adolescents' sleep quality, its causal direction has not been determined. This study used a 2-wave cross-lagged panel analysis to explore the likely causal direction between these 2 constructs. Methods: Participants were 888 Chinese adolescents (43.80%…

User's manual for MacPASCO

NASA Technical Reports Server (NTRS)

Lucas, S. H.; Davis, R. C.

1992-01-01

A user's manual is presented for MacPASCO, which is an interactive, graphic, preprocessor for panel design. MacPASCO creates input for PASCO, an existing computer code for structural analysis and sizing of longitudinally stiffened composite panels. MacPASCO provides a graphical user interface which simplifies the specification of panel geometry and reduces user input errors. The user draws the initial structural geometry and reduces user input errors. The user draws the initial structural geometry on the computer screen, then uses a combination of graphic and text inputs to: refine the structural geometry; specify information required for analysis such as panel load and boundary conditions; and define design variables and constraints for minimum mass optimization. Only the use of MacPASCO is described, since the use of PASCO has been documented elsewhere.

Viscous-Inviscid Methods in Unsteady Aerodynamic Analysis of Bio-Inspired Morphing Wings

NASA Astrophysics Data System (ADS)

Dhruv, Akash V.

Flight has been one of the greatest realizations of human imagination, revolutionizing communication and transportation over the years. This has greatly influenced the growth of technology itself, enabling researchers to communicate and share their ideas more effectively, extending the human potential to create more sophisticated systems. While the end product of a sophisticated technology makes our lives easier, its development process presents an array of challenges in itself. In last decade, scientists and engineers have turned towards bio-inspiration to design more efficient and robust aerodynamic systems to enhance the ability of Unmanned Aerial Vehicles (UAVs) to be operated in cluttered environments, where tight maneuverability and controllability are necessary. Effective use of UAVs in domestic airspace will mark the beginning of a new age in communication and transportation. The design of such complex systems necessitates the need for faster and more effective tools to perform preliminary investigations in design, thereby streamlining the design process. This thesis explores the implementation of numerical panel methods for aerodynamic analysis of bio-inspired morphing wings. Numerical panel methods have been one of the earliest forms of computational methods for aerodynamic analysis to be developed. Although the early editions of this method performed only inviscid analysis, the algorithm has matured over the years as a result of contributions made by prominent aerodynamicists. The method discussed in this thesis is influenced by recent advancements in panel methods and incorporates both viscous and inviscid analysis of multi-flap wings. The surface calculation of aerodynamic coefficients makes this method less computationally expensive than traditional Computational Fluid Dynamics (CFD) solvers available, and thus is effective when both speed and accuracy are desired. The morphing wing design, which consists of sequential feather-like flaps installed over the upper and lower surfaces of a standard airfoil, proves to be an effective alternative to standard control surfaces by increasing the flight capability of bird-scale UAVs. The results obtained for this wing design under various flight and flap configurations provide insight into its aerodynamic behavior, which enhance the maneuverability and controllability. The overall method acts as an important tool to create an aerodynamic database to develop a distributed control system for autonomous operation of the multi-flap morphing wing, supporting the use of viscous-inviscid methods as a tool in rapid aerodynamic analysis.

High resolution melting analysis is a more sensitive and effective alternative to gel-based platforms in analysis of SSR--an example in citrus.

PubMed

Distefano, Gaetano; Caruso, Marco; La Malfa, Stefano; Gentile, Alessandra; Wu, Shu-Biao

2012-01-01

High resolution melting curve analysis (HRM) has been used as an efficient, accurate and cost-effective tool to detect single nucleotide polymorphisms (SNPs) or insertions or deletions (INDELs). However, its efficiency, accuracy and applicability to discriminate microsatellite polymorphism have not been extensively assessed. The traditional protocols used for SSR genotyping include PCR amplification of the DNA fragment and the separation of the fragments on electrophoresis-based platform. However, post-PCR handling processes are laborious and costly. Furthermore, SNPs present in the sequences flanking repeat motif cannot be detected by polyacrylamide-gel-electrophoresis based methods. In the present study, we compared the discriminating power of HRM with the traditional electrophoresis-based methods and provided a panel of primers for HRM genotyping in Citrus. The results showed that sixteen SSR markers produced distinct polymorphic melting curves among the Citrus spp investigated through HRM analysis. Among those, 10 showed more genotypes by HRM analysis than capillary electrophoresis owing to the presence of SNPs in the amplicons. For the SSR markers without SNPs present in the flanking region, HRM also gave distinct melting curves which detected same genotypes as were shown in capillary electrophoresis (CE) analysis. Moreover, HRM analysis allowed the discrimination of most of the 15 citrus genotypes and the resulting genetic distance analysis clustered them into three main branches. In conclusion, it has been approved that HRM is not only an efficient and cost-effective alternative of electrophoresis-based method for SSR markers, but also a method to uncover more polymorphisms contributed by SNPs present in SSRs. It was therefore suggested that the panel of SSR markers could be used in a variety of applications in the citrus biodiversity and breeding programs using HRM analysis. Furthermore, we speculate that the HRM analysis can be employed to analyse SSR markers in a wide range of applications in all other species.

Testing and Analysis Validation of a Metallic Repair Applied to a PRSEUS Tension Panel

NASA Technical Reports Server (NTRS)

Przekop, Adam; Jegley, Dawn C.

2013-01-01

A design and analysis of a repair concept applicable to a stiffened composite panel based on the Pultruded Rod Stitched Efficient Unitized Structure was recently completed. The damage scenario considered was a midbay-to-midbay saw-cut with a severed stiffener, flange and skin. Advanced modeling techniques such as mesh-independent definition of compliant fasteners and elastic-plastic material properties for metal parts were utilized in the finite element analysis supporting the design effort. A bolted metallic repair was selected so that it could be easily applied in the operational environment. The present work describes results obtained from a tension panel test conducted to validate both the repair concept and finite element analysis techniques used in the design effort. The test proved that the proposed repair concept is capable of sustaining load levels that are higher than those resulting from the current working stress allowables. This conclusion enables upward revision of the stress allowables that had been kept at an overly-conservative level due to concerns associated with repairability of the panels. Correlation of test data with finite element analysis results is also presented and assessed.

A panel method study of vortex sheets with special emphasis on sheets of axisymmetric geometry. M.S. Thesis

NASA Technical Reports Server (NTRS)

Sugioka, I.; Widnall, S. E.

1985-01-01

The self induced evolution of a vortex sheet was simulated by modeling the sheet using an integration of discrete elements of vorticity. Replacing small sections of a vortex sheet by flat panels of constant vorticity is found to reproduce more accurately the initial conditions for the Lagrangian simulation technique than replacement by point vortices. The flat panel method for the vortex sheet was then extended to model axisymmetric vortex sheets. The local and far field velocities induced by the axisymmetric panels were obtained using matched asymptotic analysis, and some of the uncertainties involved in other models of the axisymmetric vortex sheet have been eliminated. One important result of this analysis is the determination of the proper choice of core size for a circular vortex filament which may replace a section of an axisymmetric vortex sheet. Roll-up of both two dimensional and axisymmetric vortex sheets was computed using the panel methods developed in the report.

Expert Panel Recommendations for the Identification and Management of Hyperkalemia and Role of Patiromer in Patients with Chronic Kidney Disease and Heart Failure.

PubMed

Rafique, Zubaid; Weir, Matthew R; Onuigbo, Macaulay; Pitt, Bertram; Lafayette, Richard; Butler, Javed; Lopes, Maria; Farnum, Carolyn; Peacock, W Frank

2017-04-01

Virtual panel meetings were conducted among 7 physicians, all of whom are independent experts, including 3 nephrologists, 2 cardiologists, and 2 emergency medicine physicians (the panel). The panel met with the purpose of discussing the current treatment landscape, treatment challenges, economic impact, and gaps in care for patients with hyperkalemia that is associated with heart failure and chronic kidney disease. The stated goal of the panel discussion was to develop practical solutions in the identification and management of hyperkalemia in this patient population. The panel noted that hyperkalemia is a serious condition that can lead to life-threatening complications, yet the treatment paradigm for hyperkalemia has remained without major advances for approximately 50 years, until the approval of patiromer. A number of issues still exist in the management of this patient population, including the lack of uniform treatment guidelines and consensus regarding the approach to treatment. As part of its effort, the panel developed an algorithm, the Proposed Diagnostic Algorithm for Hyperkalemia Treatment in the Acute Care Setting/Chronic Care. The panel agreed that patiromer appears to be a viable option for the management of hyperkalemia in patients with chronic kidney disease and/or heart failure and in patients who experience chronic hyperkalemia. This panel discussion was funded by Relypsa and facilitated by Magellan Rx Management. Rafique is a principal investigator for Relypsa and serves as a consultant for Instrumentation Laboratory, Magellan Health, Relypsa, and ZS-Pharma. Butler serves as consultant for Amgen, AstraZeneca, Bayer, Boehringer Ingelheim, CardioCell, Janssen, Merck, Novartis, Relypsa, and ZS-Pharma. Lopes and Farnum are employed by Magellan Rx Management. Rafique designed the management protocol for this panel discussion and contributed to the writing and editing of this report document. The other authors report no conflicting interests. Relypsa is the manufacturer of Veltassa (patiromer).

Application of Remote Sensing to the Chesapeake Bay Region. Volume 2: Proceedings

NASA Technical Reports Server (NTRS)

Chen, W. T. (Editor); Freas, G. W., Jr. (Editor); Hickman, G. D. (Editor); Pemberton, D. A. (Editor); Wilkerson, T. D. (Editor); Adler, I. (Editor); Laurie, V. J. (Editor)

1978-01-01

A conference was held on the application of remote sensing to the Chesapeake Bay region. Copies of the papers, resource contributions, panel discussions, and reports of the working groups are presented.

Advanced composites structural concepts and materials technologies for primary aircraft structures: Structural response and failure analysis

NASA Technical Reports Server (NTRS)

Dorris, William J.; Hairr, John W.; Huang, Jui-Tien; Ingram, J. Edward; Shah, Bharat M.

1992-01-01

Non-linear analysis methods were adapted and incorporated in a finite element based DIAL code. These methods are necessary to evaluate the global response of a stiffened structure under combined in-plane and out-of-plane loading. These methods include the Arc Length method and target point analysis procedure. A new interface material model was implemented that can model elastic-plastic behavior of the bond adhesive. Direct application of this method is in skin/stiffener interface failure assessment. Addition of the AML (angle minus longitudinal or load) failure procedure and Hasin's failure criteria provides added capability in the failure predictions. Interactive Stiffened Panel Analysis modules were developed as interactive pre-and post-processors. Each module provides the means of performing self-initiated finite elements based analysis of primary structures such as a flat or curved stiffened panel; a corrugated flat sandwich panel; and a curved geodesic fuselage panel. This module brings finite element analysis into the design of composite structures without the requirement for the user to know much about the techniques and procedures needed to actually perform a finite element analysis from scratch. An interactive finite element code was developed to predict bolted joint strength considering material and geometrical non-linearity. The developed method conducts an ultimate strength failure analysis using a set of material degradation models.

Coupled Thermo-Electro-Magneto-Elastic Response of Smart Stiffened Panels

NASA Technical Reports Server (NTRS)

Bednarcyk, Brett A.; Yarrington, Phillip W.

2009-01-01

This report documents the procedures developed for incorporating smart laminate and panel analysis capabilities within the HyperSizer aerospace structural sizing software package. HyperSizer analyzes stiffened panels composed of arbitrary composite laminates through stiffener homogenization, or "smearing " techniques. The result is an effective constitutive equation for the stiffened panel that is suitable for use in a full vehicle-scale finite element analysis via MSC/NASTRAN. The existing thermo-elastic capabilities of HyperSizer have herein been extended to include coupled thermo-electro-magneto-elastic analysis capabilities. This represents a significant step toward realization of design tools capable of guiding the development of the next generation of smart aerospace structures. Verification results are presented that compare the developed smart HyperSizer capability with an ABAQUS piezoelectric finite element solution for a facesheet-flange combination. These results show good agreement between HyperSizer and ABAQUS, but highlight a limitation of the HyperSizer formulation in that constant electric field components are assumed.

Active control of sound transmission through a double panel partition

NASA Astrophysics Data System (ADS)

Sas, P.; Bao, C.; Augusztinovicz, F.; Desmet, W.

1995-03-01

The feasibility of improving the insertion loss of lightweight double panel partitions by using small loudspeakers as active noise control sources inside the air gap between both panels of the partition is investigated analytically, numerically and experimentally in this paper. A theoretical analysis of the mechanisms of the fluid-structure interaction of double panel structures is presented in order to gain insight into the physical phenomena underlying the behaviour of a coupled vibro-acoustic system controlled by active methods. The analysis, based on modal coupling theory, enables one to derive some qualitative predictions concerning the potentials and limitations of the proposed approach. The theoretical analysis is valid only for geometrically simple structures. For more complex geometries, numerical simulations are required. Therefore the potential use of active noise control inside double panel structures has been analyzed by using coupled finite element and boundary element methods. To verify the conclusions drawn from the theoretical analysis and the numerical calculation and, above all, to demonstrate the potential of the proposed approach, experiments have been conducted with a laboratory set-up. The performance of the proposed approach was evaluated in terms of relative insertion loss measurements. It is shown that a considerable improvement of the insertion loss has been achieved around the lightly damped resonances of the system for the frequency range investigated (60-220 Hz).

Flight Testing of Night Vision Systems in Rotorcraft (Test en vol de systemes de vision nocturne a bord des aeronefs a voilure tournante)

DTIC Science & Technology

2007-07-01

SAS System Analysis and Studies Panel • SCI Systems Concepts and Integration Panel • SET Sensors and Electronics Technology Panel These...Daylight Readability 4-2 4.1.4 Night-Time Readability 4-2 4.1.5 NVIS Radiance 4-2 4.1.6 Human Factors Analysis 4-3 4.1.7 Flight Tests 4-3 4.1.7.1...position is shadowing. Moonlight creates shadows during night-time just as sunlight does during the day. Understanding what cannot be seen in night-time

Prediction of transmission loss through an aircraft sidewall using statistical energy analysis

NASA Astrophysics Data System (ADS)

Ming, Ruisen; Sun, Jincai

1989-06-01

The transmission loss of randomly incident sound through an aircraft sidewall is investigated using statistical energy analysis. Formulas are also obtained for the simple calculation of sound transmission loss through single- and double-leaf panels. Both resonant and nonresonant sound transmissions can be easily calculated using the formulas. The formulas are used to predict sound transmission losses through a Y-7 propeller airplane panel. The panel measures 2.56 m x 1.38 m and has two windows. The agreement between predicted and measured values through most of the frequency ranges tested is quite good.

The Shock and Vibration Digest, Volume 14, Number 2, February 1982

DTIC Science & Technology

1982-02-01

figurations. 75 4J DUCTS 82-424 (Also see No. 346) Coupling Lou Factors for Statistical Energy Analysis of Sound Transnission at Rectangular...waves, Sound waves, Wave props- tures by means of statistical energy analysis (SEA) coupling gation loss factors for the structure-borne sound...multilayered panels are discussed. Statistical energy analysis (SEA) has proved to be a promising Experimental results of stiffened panels, damping tape

Orthogonal model and experimental data for analyzing wood-fiber-based tri-axial ribbed structural panels in bending

Treesearch

Jinghao Li; John F. Hunt; Shaoqin Gong; Zhiyong Cai

2017-01-01

This paper presents an analysis of 3-dimensional engineered structural panels (3DESP) made from wood-fiber-based laminated paper composites. Since the existing models for calculating the mechanical behavior of core configurations within sandwich panels are very complex, a new simplified orthogonal model (SOM) using an equivalent element has been developed. This model...

About sound mufflers sound-absorbing panels aircraft engine

NASA Astrophysics Data System (ADS)

Dudarev, A. S.; Bulbovich, R. V.; Svirshchev, V. I.

2016-10-01

The article provides a formula for calculating the frequency of sound absorbed panel with a perforated wall. And although the sound absorbing structure is a set of resonators Helmholtz, not individual resonators should be considered in acoustic calculations, and all the perforated wall panel. The analysis, showing how the parameters affect the size and sound-absorbing structures in the absorption rate.

Fiscal Analysis of the Report of the Select Panel on Revisioning Education in Maine

ERIC Educational Resources Information Center

Silvernail, David L.; Batista, Ida A.

2006-01-01

In late 2005 the Select Panel on Revisioning Education in Maine issued their draft report describing a series of recommendations for the improvement of student learning in Maine. The Panel, convened by the Maine State Board of Education, and pursuant to Tile 20-A statutory requirements, developed their recommendations through six months of data…

Economic analysis of complementary, alternative, and integrative medicine: considerations raised by an expert panel.

PubMed

Coulter, Ian D; Herman, Patricia M; Nataraj, Shanthi

2013-07-25

An international panel of experts was convened to examine the challenges faced in conducting economic analyses of Complementary, Alternative and Integrative Medicine (CAIM). A one and a half-day panel of experts was convened in early 2011 to discuss what was needed to bring about robust economic analysis of CAIM. The goals of the expert panel were to review the current state of the science of economic evaluations in health, and to discuss the issues involved in applying these methods to CAIM, recognizing its unique characteristics. The panel proceedings were audiotaped and a thematic analysis was conducted independently by two researchers. The results were then discussed and differences resolved. This manuscript summarizes the discussions held by the panel members on each theme. The panel identified seven major themes regarding economic evaluation that are particularly salient to determining the economics of CAIM: standardization (in order to compare CAIM with conventional therapies, the same basic economic evaluation methods and framework must be used); identifying the question being asked, the audience targeted for the results and whose perspective is being used (e.g., the patient perspective is especially relevant to CAIM because of the high level of self-referral and out-of-pocket payment); the analytic methods to be used (e.g., the importance of treatment description and fidelity); the outcomes to be measured (e.g., it is important to consider a broad range of outcomes, particularly for CAIM therapies, which often treat the whole person rather than a specific symptom or disease); costs (e.g., again because of treating the whole person, the impact of CAIM on overall healthcare costs, rather than only disease-specific costs, should be measured); implementation (e.g., highlighting studies where CAIM allows cost savings may help offset its image as an "add on" cost); and generalizability (e.g., proper reporting can enable study results to be useful beyond the study sample). The business case for CAIM depends on economic analysis and standard methods for conducting such economic evaluations exist. The challenge for CAIM lies in appropriately applying these methods. The deliberations of this panel provide a list of factors to be considered in meeting that challenge.

Postbuckling behavior of axially compressed graphite-epoxy cylindrical panels with circular holes

NASA Technical Reports Server (NTRS)

Knight, N. F., Jr.; Starnes, J. H., Jr.

1984-01-01

The results of an experimental and analytical study of the effects of circular holes on the postbuckling behavior of graphite-epoxy cylindrical panels loaded in axial compression are presented. The STAGSC-1 general shell analysis computer code is used to determine the buckling and postbuckling response of the panels. The loaded, curved ends of the specimens were clamped by fixtures and the unloaded, straight edges were simply supported by knife-edge restraints. The panels are loaded by uniform end shortening to several times the end shortening at buckling. The unstable equilibrium path of the postbuckling response is obtained analytically by using a method based on controlling an equilibrium-path-arc-length parameter instead of the traditional load parameter. The effects of hole diameter, panel radius, and panel thickness on postbuckling response are considered in the study. Experimental results are compared with the analytical results and the failure characteristics of the graphite-epoxy panels are described.

POSTOP: Postbuckled open-stiffener optimum panels, user's manual

NASA Technical Reports Server (NTRS)

Biggers, S. B.; Dickson, J. N.

1984-01-01

The computer program POSTOP developed to serve as an aid in the analysis and sizing of stiffened composite panels that may be loaded in the postbuckling regime, is intended for the preliminary design of metal or composite panels with open-section stiffeners, subjected to multiple combined biaxial compression (or tension), shear and normal pressure load cases. Longitudinal compression, however, is assumed to be the dominant loading. Temperature, initial bow eccentricity and load eccentricity effects are included. The panel geometry is assumed to be repetitive over several bays in the longitudinal (stiffener) direction as well as in the transverse direction. Analytical routines are included to compute panel stiffnesses, strains, local and panel buckling loads, and skin/stiffener interface stresses. The resulting program is applicable to stiffened panels as commonly used in fuselage, wing, or empennage structures. The capabilities and limitations of the code are described. Instructions required to use the program and several example problems are included.

Simplified Calculation Model and Experimental Study of Latticed Concrete-Gypsum Composite Panels

PubMed Central

Jiang, Nan; Ma, Shaochun

2015-01-01

In order to address the performance complexity of the various constituent materials of (dense-column) latticed concrete-gypsum composite panels and the difficulty in the determination of the various elastic constants, this paper presented a detailed structural analysis of the (dense-column) latticed concrete-gypsum composite panel and proposed a feasible technical solution to simplified calculation. In conformity with mechanical rules, a typical panel element was selected and divided into two homogenous composite sub-elements and a secondary homogenous element, respectively for solution, thus establishing an equivalence of the composite panel to a simple homogenous panel and obtaining the effective formulas for calculating the various elastic constants. Finally, the calculation results and the experimental results were compared, which revealed that the calculation method was correct and reliable and could meet the calculation needs of practical engineering and provide a theoretical basis for simplified calculation for studies on composite panel elements and structures as well as a reference for calculations of other panels. PMID:28793631

Simplified Calculation Model and Experimental Study of Latticed Concrete-Gypsum Composite Panels.

PubMed

Jiang, Nan; Ma, Shaochun

2015-10-27

In order to address the performance complexity of the various constituent materials of (dense-column) latticed concrete-gypsum composite panels and the difficulty in the determination of the various elastic constants, this paper presented a detailed structural analysis of the (dense-column) latticed concrete-gypsum composite panel and proposed a feasible technical solution to simplified calculation. In conformity with mechanical rules, a typical panel element was selected and divided into two homogenous composite sub-elements and a secondary homogenous element, respectively for solution, thus establishing an equivalence of the composite panel to a simple homogenous panel and obtaining the effective formulas for calculating the various elastic constants. Finally, the calculation results and the experimental results were compared, which revealed that the calculation method was correct and reliable and could meet the calculation needs of practical engineering and provide a theoretical basis for simplified calculation for studies on composite panel elements and structures as well as a reference for calculations of other panels.

Orthosiphon stamineus protects Caenorhabditis elegans against Staphylococcus aureus infection through immunomodulation

PubMed Central

Kong, Cin; Tan, Man-Wah; Nathan, Sheila

2014-01-01

ABSTRACT Amidst growing concerns over the spread of antibiotic-resistant Staphylococcus aureus strains, the identification of alternative therapeutic molecules has become paramount. Previously, we utilized a Caenorhabditis elegans–S. aureus screening platform to identify potential anti-infective agents from a collection of natural extracts and synthetic compounds. One of the hits obtained from the screen was the aqueous extract of Orthosiphon stamineus leaves (UE-12) that enhanced the survival of infected nematodes without interfering with bacterial growth. In this study, we used a fluorescent transgenic reporter strain and observed that the repressed expression of the lys-7 defense gene in infected nematodes was restored in the presence of UE-12. Analysis of a selected panel of PMK-1 and DAF-16-regulated transcripts and loss-of-function mutants in these pathways indicates that the protective role of UE-12 is mediated via the p38 MAP kinase and insulin-like signaling pathways. Further analysis of a panel of known bioactive compounds of UE-12 proposed eupatorin (C18H16O7) as the possible candidate active molecule contributing to the anti-infective property of UE-12. Taken together, these findings strongly suggest that the O. stamineus leaf extract is a promising anti-infective agent that confers an advantage in survival against S. aureus infection by modulating the immune response of the infected host. PMID:24972867

'Global health' and 'global nursing': proposed definitions from The Global Advisory Panel on the Future of Nursing.

PubMed

Wilson, Lynda; Mendes, Isabel Amelia Costa; Klopper, Hester; Catrambone, Cathy; Al-Maaitah, Rowaida; Norton, Mary E; Hill, Martha

2016-07-01

To propose definitions of global health and global nursing that reflect the new paradigm that integrates domestic and international health. Increased globalization has led to expanded awareness of the importance of global health and global nursing among students and faculty in the health professions and among policymakers and practitioners. Discussion paper that includes a discussion and review of the literature related to global health and global nursing. A task force searched for and reviewed articles published in English, Spanish or Portuguese between 2005-2015, developed summaries, listed key elements, identified prevalent themes and developed consensus definitions. The definitions will be used by the Global Advisory Panel on the Future of Nursing to guide promoting a voice and vision for nursing that will contribute to the advancement of the profession's contribution to global health. Definitions of global health and global nursing were developed based on main themes and concepts identified in the literature review to guide contributions of nursing to global health. © 2016 John Wiley & Sons Ltd.

Evaluation of fiberglass sign panels.

DOT National Transportation Integrated Search

1989-01-01

This study investigated the feasibility of using fiberglass reinforced plastic material as an alternative to aluminum for highway sign panels. An analysis of shop fabrication, installation procedures, field performance, reclamation, and cost was made...

Nonlinear flutter analysis of composite panels

NASA Astrophysics Data System (ADS)

An, Xiaomin; Wang, Yan

2018-05-01

Nonlinear panel flutter is an interesting subject of fluid-structure interaction. In this paper, nonlinear flutter characteristics of curved composite panels are studied in very low supersonic flow. The composite panel with geometric nonlinearity is modeled by a nonlinear finite element method; and the responses are computed by the nonlinear Newmark algorithm. An unsteady aerodynamic solver, which contains a flux splitting scheme and dual time marching technology, is employed in calculating the unsteady pressure of the motion of the panel. Based on a half-step staggered coupled solution, the aeroelastic responses of two composite panels with different radius of R = 5 and R = 2.5 are computed and compared with each other at different dynamic pressure for Ma = 1.05. The nonlinear flutter characteristics comprising limited cycle oscillations and chaos are analyzed and discussed.

Targeted gene panels and microbiota analysis provide insight into the effects of effects of alternative production diet formulations on channel catfish nutritional physiology

USDA-ARS?s Scientific Manuscript database

The present research evaluated targeted gene panels and microbiota analysis to provide greater insight into the effects of alternatively-sourced dietary ingredients on production indices, gut health, changes in the gut microbiota and genes involved in the regulation of appetite, growth, metabolism, ...

Environmental Influences on Well-Being: A Dyadic Latent Panel Analysis of Spousal Similarity

ERIC Educational Resources Information Center

Schimmack, Ulrich; Lucas, Richard E.

2010-01-01

This article uses dyadic latent panel analysis (DLPA) to examine environmental influences on well-being. DLPA requires longitudinal dyadic data. It decomposes the observed variance of both members of a dyad into a trait, state, and an error component. Furthermore, state variance is decomposed into initial and new state variance. Total observed…

Pulpwood supply and demand : development in the South, little growth elsewhere.

Treesearch

Peter J. Ince; Irene Durbak

2002-01-01

This long-range outlook derives from analysis of pulp and paper markets and pulpwood demands for wood panels. The analysis projects modest increases in pulpwood demand beyond 2010, with decelerating growth in paper and paperboard consumption; increased demand for pulpwood in wood panels; increased imports of pulp, paper, and paperboard; and little additional growth in...

Evaluation of a Highly Anticlastic Panel with Tow Overlaps

NASA Technical Reports Server (NTRS)

Wu, K. Chauncey; Gurdal, Zafer

2007-01-01

A rectangular, variable-stiffness panel with tow overlaps was manufactured using an advanced tow placement machine. The cured panel had large anticlastic imperfections, with measured amplitudes of over two times the average panel thickness. These imperfections were not due to the overall steered-fiber layup or the tow overlaps, but instead resulted from local asymmetries in the laminate that were caused by a manufacturing oversight. In the nominal panel layup, fiber angles vary linearly from 60 degrees on the panel axial centerline to 30 degrees on the parallel edges. A geometrically nonlinear analysis was performed with a -280 degree Fahrenheit thermal load to simulate the postcure cooldown to room temperature. The predicted geometric imperfections correlated well with the measured panel shape. Unique structural test fixtures were then developed which greatly reduced these imperfections, but they also caused prestresses in the panel. Surface imperfections measured after the panel was installed in the test fixtures were used with nonlinear finite element analyses to predict these fixturing-induced prestresses. These prestresses were also included in structural analyses of panel end compression to failure, and the analytical results compared well with test data when both geometric and material nonlinearities were included.

Occupational and Environmental Contributions to Chronic Cough in Adults: Chest Expert Panel Report.

PubMed

Tarlo, Susan M; Altman, Kenneth W; Oppenheimer, John; Lim, Kaiser; Vertigan, Anne; Prezant, David; Irwin, Richard S

2016-10-01

In response to occupational and environmental exposures, cough can be an isolated symptom reflecting exposure to an irritant with little physiological consequence, or it can be a manifestation of more significant disease. This document reviews occupational and environmental contributions to chronic cough in adults, focusing on aspects not previously covered in the 2006 ACCP Cough Guideline or our more recent systematic review, and suggests an approach to investigation of these factors when suspected. MEDLINE and TOXLINE literature searches were supplemented by articles identified by the cough panel occupational and environmental subgroup members, to identify occupational and environmental aspects of chronic cough not previously covered in the 2006 ACCP Cough Guideline. Based on the literature reviews and the Delphi methodology, the cough panel occupational and environmental subgroup developed guideline suggestions that were approved after review and voting by the full cough panel. The literature review identified relevant articles regarding: mechanisms; allergic environmental causes; chronic cough and the recreational and involuntary inhalation of tobacco and marijuana smoke; nonallergic environmental triggers; laryngeal syndromes; and occupational diseases and exposures. Consensus-based statements were developed for the approach to diagnosis due to a lack of strong evidence from published literature. Despite increased understanding of cough related to occupational and environmental triggers, there remains a gap between the recommended assessment of occupational and environmental causes of cough and the reported systematic assessment of these factors. There is a need for further documentation of occupational and environmental causes of cough in the future. Copyright © 2016 American College of Chest Physicians. Published by Elsevier Inc. All rights reserved.

Energy absorption capabilities of composite sandwich panels under blast loads

NASA Astrophysics Data System (ADS)

Sankar Ray, Tirtha

As blast threats on military and civilian structures continue to be a significant concern, there remains a need for improved design strategies to increase blast resistance capabilities. The approach to blast resistance proposed here is focused on dissipating the high levels of pressure induced during a blast through maximizing the potential for energy absorption of composite sandwich panels, which are a competitive structural member type due to the inherent energy absorption capabilities of fiber reinforced polymer (FRP) composites. Furthermore, the middle core in the sandwich panels can be designed as a sacrificial layer allowing for a significant amount of deformation or progressive failure to maximize the potential for energy absorption. The research here is aimed at the optimization of composite sandwich panels for blast mitigation via energy absorption mechanisms. The energy absorption mechanisms considered include absorbed strain energy due to inelastic deformation as well as energy dissipation through progressive failure of the core of the sandwich panels. The methods employed in the research consist of a combination of experimentally-validated finite element analysis (FEA) and the derivation and use of a simplified analytical model. The key components of the scope of work then includes: establishment of quantified energy absorption criteria, validation of the selected FE modeling techniques, development of the simplified analytical model, investigation of influential core architectures and geometric parameters, and investigation of influential material properties. For the parameters that are identified as being most-influential, recommended values for these parameters are suggested in conceptual terms that are conducive to designing composite sandwich panels for various blast threats. Based on reviewing the energy response characteristic of the panel under blast loading, a non-dimensional parameter AET/ ET (absorbed energy, AET, normalized by total energy, ET) was suggested to compare energy absorption capabilities of the structures under blast loading. In addition, AEweb/ET (where AEweb is the energy absorbed by the middle core) was also employed to evaluate the energy absorption contribution from the web. Taking advantage of FEA and the simplified analytical model, the influences of material properties as well as core architectures and geometries on energy absorption capabilities (quantified by AET/ ET and AEweb/E T) were investigated through parametric studies. Results from the material property investigation indicated that density of the front face sheet and strength were most influential on the energy absorption capability of the composite sandwich panels under blast loading. The study to investigate the potential effectiveness of energy absorbed via inelastic deformation compared to energy absorbed via progressive failure indicated that for practical applications (where the position of bomb is usually unknown and the panel is designed to be the same anywhere), the energy absorption via inelastic deformation is the more efficient approach. Regarding the geometric optimization, it was found that a core architecture consisting of vertically-oriented webs was ideal. The optimum values for these parameters can be generally described as those which cause the most inelasticity, but not failure, of the face sheets and webs.

Lightweight composites for modular panelized construction

NASA Astrophysics Data System (ADS)

Vaidya, Amol S.

Rapid advances in construction materials technology have enabled civil engineers to achieve impressive gains in the safety, economy, and functionality of structures built to serve the common needs of society. Modular building systems is a fast-growing modern, form of construction gaining recognition for its increased efficiency and ability to apply modern technology to the needs of the market place. In the modular construction technique, a single structural panel can perform a number of functions such as providing thermal insulation, vibration damping, and structural strength. These multifunctional panels can be prefabricated in a manufacturing facility and then transferred to the construction site. A system that uses prefabricated panels for construction is called a "panelized construction system". This study focuses on the development of pre-cast, lightweight, multifunctional sandwich composite panels to be used for panelized construction. Two thermoplastic composite panels are proposed in this study, namely Composite Structural Insulated Panels (CSIPs) for exterior walls, floors and roofs, and Open Core Sandwich composite for multifunctional interior walls of a structure. Special manufacturing techniques are developed for manufacturing these panels. The structural behavior of these panels is analyzed based on various building design codes. Detailed descriptions of the design, cost analysis, manufacturing, finite element modeling and structural testing of these proposed panels are included in this study in the of form five peer-reviewed journal articles. The structural testing of the proposed panels involved in this study included flexural testing, axial compression testing, and low and high velocity impact testing. Based on the current study, the proposed CSIP wall and floor panels were found satisfactory, based on building design codes ASCE-7-05 and ACI-318-05. Joining techniques are proposed in this study for connecting the precast panels on the construction site. Keywords: Modular panelized construction, sandwich composites, composite structural insulated panels (CSIPs).

Emerged/Emerging Disruptive Technologies (E2DT) (Technologies de rupture apparues/emergentes (E2DT)). Proceedings of the RTO Information Systems Technology Panel (IST) Symposium held in Madrid, Spain on 7-8 May 2011

DTIC Science & Technology

2011-05-01

with the potential to impact future military Information Systems. The second is to explore and identify innovative applications of these emerging or...NATO) BP 25, F-92201 Neuilly- sur -Seine Cedex, France RTO-MP-IST-099 Approved for Public release, distribution unlimited. Supporting documents are...Analysis and Studies Panel • SCI Systems Concepts and Integration Panel • SET Sensors and Electronics Technology Panel These bodies are made up of

Imperfection and Thickness Measurement of Panels Using a Coordinate Measurement Machine

NASA Technical Reports Server (NTRS)

Thornburgh, Robert P.

2006-01-01

This paper summarizes the methodology used to measure imperfection and thickness variation for flat and curved panels using a Coordinate Measurement Machine (CMM) and the software program MeasPanel. The objective is to provide a reference document so that someone with a basic understanding of CMM operation can measure a panel with minimal training. Detailed information about both the measurement system setup and computer software is provided. Information is also provided about the format of the raw data, as well as how it is post-processed for use in finite-element analysis.

Prediction and verification of creep behavior in metallic materials and components for the space shuttle thermal protection system. Volume 3, phase 3: Full size heat shield data correlation and design criteria. [reentry

NASA Technical Reports Server (NTRS)

Cramer, B. A.; Davis, J. W.

1975-01-01

Analysis methods for predicting cyclic creep deflection in stiffened metal panel structures, were applied to full size panels. Results were compared with measured deflections from cyclic tests of thin gage L605, Rene' 41, and TDNiCr full size corrugation stiffened panels. A design criteria was then formulated for metallic thermal protection panels subjected to creep. A computer program was developed to calculate creep deflections.

Linking Indigenous Knowledge and Observed Climate Change Studies

NASA Technical Reports Server (NTRS)

Alexander, Chief Clarence; Bynum, Nora; Johnson, Liz; King, Ursula; Mustonen, Tero; Neofotis, Peter; Oettle, Noel; Rosenzweig, Cynthia; Sakakibara, Chie; Shadrin, Chief Vyacheslav;

ICASE/LaRC Workshop on Adaptive Grid Methods

NASA Technical Reports Server (NTRS)

South, Jerry C., Jr. (Editor); Thomas, James L. (Editor); Vanrosendale, John (Editor)

1995-01-01

Solution-adaptive grid techniques are essential to the attainment of practical, user friendly, computational fluid dynamics (CFD) applications. In this three-day workshop, experts gathered together to describe state-of-the-art methods in solution-adaptive grid refinement, analysis, and implementation; to assess the current practice; and to discuss future needs and directions for research. This was accomplished through a series of invited and contributed papers. The workshop focused on a set of two-dimensional test cases designed by the organizers to aid in assessing the current state of development of adaptive grid technology. In addition, a panel of experts from universities, industry, and government research laboratories discussed their views of needs and future directions in this field.

Novel mutations in the TULP1 gene causing autosomal recessive retinitis pigmentosa.

PubMed

Paloma, E; Hjelmqvist, L; Bayés, M; García-Sandoval, B; Ayuso, C; Balcells, S; Gonzàlez-Duarte, R

2000-03-01

To assess the contribution of TULP1 to autosomal recessive retinitis pigmentosa (arRP). Fifteen exons of the gene were screened by single-strand conformation polymorphism analysis of 7 (of 49) arRP pedigrees showing cosegregation with TULP1 locus markers. In one of the seven families two allelic mutations, IVS4-2delAGA and c.937delC, were found in exons 5 and 10, respectively. Two novel mutations in TULP1 were found to be associated with arRP. That they both compromise the gene product supports their pathogenicity. This gene was present in no more than 2% of a panel of 49 Spanish families affected by arRP.

Summary Report Panel 1: The Need for Protocols and Standards in Research on Underwater Noise Impacts on Marine Life.

PubMed

Erbe, Christine; Ainslie, Michael A; de Jong, Christ A F; Racca, Roberto; Stocker, Michael

2016-01-01

As concern about anthropogenic noise and its impacts on marine fauna is increasing around the globe, data are being compared across populations, species, noise sources, geographic regions, and time. However, much of the raw and processed data are not comparable due to differences in measurement methodology, analysis and reporting, and a lack of metadata. Common protocols and more formal, international standards are needed to ensure the effectiveness of research, conservation, regulation and practice, and unambiguous communication of information and ideas. Developing standards takes time and effort, is largely driven by a few expert volunteers, and would benefit from stakeholders' contribution and support.

Systems GMM estimates of the health care spending and GDP relationship: a note.

PubMed

Kumar, Saten

2013-06-01

This paper utilizes the systems generalized method of moments (GMM) [Arellano and Bover (1995) J Econometrics 68:29-51; Blundell and Bond (1998) J Econometrics 87:115-143], and panel Granger causality [Hurlin and Venet (2001) Granger Causality tests in panel data models with fixed coefficients. Mime'o, University Paris IX], to investigate the health care spending and gross domestic product (GDP) relationship for organisation for economic co-operation and development countries over the period 1960-2007. The system GMM estimates confirm that the contribution of real GDP to health spending is significant and positive. The panel Granger causality tests imply that a bi-directional causality exists between health spending and GDP. To this end, policies aimed at raising health spending will eventually improve the well-being of the population in the long run.

Final Report of the Haystack Orbital Debris Data Review Panel

NASA Technical Reports Server (NTRS)

Barton, David K.; Brillinger, David; McDaniel, Patrick; Pollock, Kenneth H.; El-Shaarawi, A. H.; Tuley, Michael T.

1998-01-01

The Haystack Orbital Debris Data Review Panel was established in December 1996 to consider the adequacy of the data on orbital debris gathered over the past several years with the Haystack radar, and the accuracy of the methods used to estimate the flux vs. size relationship for this debris. The four specific issues addressed for the Panel were: 1. The number of observations relative to the estimated population of interest 2. The inherent ambiguity between the measured radar cross section (RCS) and the inferred physical size of the object 3. The inherent aspect angle limitation in viewing each object and its relationship to object geometry 4. The adequacy of the sample data set to characterize the debris population's potential geometry. Further discussion and interpretation of these issues, and identification of the detailed questions contributing to them, are discussed in this report.

A Qualitative Evaluation of Ethics Educational Program in Health Science.

PubMed

Ekmekci, Perihan Elif; Oral, Murat; Yurdakul, Eray Serdar

2015-06-01

This paper originates from a panel discussion on the evaluation of "Ethics Educational Program in Health Sciences" held during the IAEE Conference 2014 Ankara, Turkey. The participants of the panel had consultations to solidify the concepts about the topic. The qualitative data out of these antecedent discussions became mature with the contributions in the panel. The outcome of this qualitative study mainly focuses on the examples of two current curricula; one from PhD on History of Medicine and Medical Ethics, the other one from an elective course on medical ethics as a part of a PhD program on Pharmacy Management and History, followed by the major challenges the trainees face during their education, their expectations and whether the program was satisfactory, the aspects of the programs which are prone to improvement and their overall evaluations of the programs.

Report of the panel on plate motion and deformation, section 2

NASA Technical Reports Server (NTRS)

Bock, Yehuda; Kastens, Kim A.; Mcnutt, Marcia K.; Minster, J. Bernard; Peltzer, Gilles; Prescott, William H.; Reilinger, Robert E.; Royden, Leigh; Rundle, John B.; Sauber, Jeanne M.

1991-01-01

Given here is a panel report on the goals and objectives, requirements and recommendations for the investigation of plate motion and deformation. The goals are to refine our knowledge of plate motions, study regional and local deformation, and contribute to the solution of important societal problems. The requirements include basic space-positioning measurements, the use of global and regional data sets obtained with space-based techniques, topographic and geoid data to help characterize the internal processes that shape the planet, gravity data to study the density structure at depth and help determine the driving mechanisms for plate tectonics, and satellite images to map lithology, structure and morphology. The most important recommendation of the panel is for the implementation of a world-wide space-geodetic fiducial network to provide a systematic and uniform measure of global strain.

Single-strain-gage force/stiffness buckling prediction techniques on a hat-stiffened panel

NASA Technical Reports Server (NTRS)

Hudson, Larry D.; Thompson, Randolph C.

1991-01-01

Predicting the buckling characteristics of a test panel is necessary to ensure panel integrity during a test program. A single-strain-gage buckling prediction method was developed on a hat-stiffened, monolithic titanium buckling panel. The method is an adaptation of the original force/stiffness method which requires back-to-back gages. The single-gage method was developed because the test panel did not have back-to-back gages. The method was used to predict buckling loads and temperatures under various heating and loading conditions. The results correlated well with a finite element buckling analysis. The single-gage force/stiffness method was a valid real-time and post-test buckling prediction technique.

Stress Behaviour in Compression of Contact-Monolithic Joint of Self-Supporting Wall of Large Panel Multi-Storey Building

NASA Astrophysics Data System (ADS)

Derbentsev, I.; Karyakin, A. A.; Volodin, A.

2017-11-01

The article deals with the behaviour of a contact-monolithic joint of large-panel buildings under compression. It gives a detailed analysis and the descriptions of the stages of such joints failure based on the results of the tests and computational modelling. The article is of interest to specialists who deal with computational modelling or the research of large-panel multi-storey buildings. The text gives a valuable information on the values of their bearing capacity and flexibility, the eccentricity of load transfer from upper panel to lower, the value of thrust passed to a ceiling panel. Recommendations are given to estimate all the above-listed parameters.

Preparing for Large-Force Exercises with Distributed Simulation: A Panel Presentation

DTIC Science & Technology

2010-07-01

Preparing for Large Force Exercises with Distributed Simulation: A Panel Presentation Peter Crane, Winston Bennett, Michael France Air Force...used distributed simulation training to complement live-fly exercises to prepare for LFEs. In this panel presentation , the speakers will describe... presentations on how detailed analysis of training needs is necessary to structure simulator scenarios and how future training exercises could be made more

Face-Sheet Quality Analysis and Thermo-Physical Property Characterization of OOA and Autoclave Panels

NASA Technical Reports Server (NTRS)

Miller, Sandi G.; Lort, Richard D., III; Zimmerman, Thomas J.; Sutter, James K.; Pelham, Larry I.; McCorkle, Linda S.; Scheiman, Daniel A.

2012-01-01

Increased application of polymer matrix composite (PMC) materials in large vehicle structures requires consideration of non-autoclave manufacturing technology. The NASA Composites for Exploration project, and its predecessor, Lightweight Spacecraft Structures and Materials project, were tasked with the development of materials and manufacturing processes for structures that will perform in a heavy-lift-launch vehicle environment. Both autoclave and out of autoclave processable materials were considered. Large PMC structures envisioned for such a vehicle included the payload shroud and the interstage connector. In this study, composite sandwich panels representing 1/16th segments of the barrel section of the Ares V rocket fairing were prepared as 1.8 m x 2.4 m sections of the 10 m diameter arc segment. IM7/977-3 was used as the face-sheet prepreg of the autoclave processed panels and T40-800B/5320-1 for the out of autoclave panels. The core was 49.7 kg/sq m (3.1 lb/cu ft (pcf)) aluminum honeycomb. Face-sheets were fabricated by automated tape laying 153 mm wide unidirectional tape. This work details analysis of the manufactured panels where face-sheet quality was characterized by optical microscopy, cured ply thickness measurements, acid digestion, and thermal analysis.

Face-Sheet Quality Analysis and Thermo-Physical Property Characterization of OOA and Autoclave Panels

NASA Technical Reports Server (NTRS)

Miller, Sandi G.; Lort, Richard D., III; Zimmerman, Thomas J.; Sutter, James K.; Pelham, Larry I.; McCorkle, Linda S.; Scheiman, Daniel A.

2012-01-01

Increased application of polymer matrix composite (PMC) materials in large vehicle structures requires consideration of non-autoclave manufacturing technology. The NASA Composites for Exploration project, and its predecessor, Lightweight Spacecraft Structures and Materials project, were tasked with the development of materials and manufacturing processes for structures that will perform in a heavy-lift-launch vehicle environment. Both autoclave and out of autoclave processable materials were considered. Large PMC structures envisioned for such a vehicle included the payload shroud and the interstage connector. In this study, composite sandwich panels representing 1/16th segments of the barrel section of the Ares V rocket fairing were prepared as 1.8 m x 2.4 m sections of the 10 m diameter arc segment. IM7/977-3 was used as the face-sheet prepreg of the autoclave processed panels and T40-800B/5320-1 for the out of autoclave panels. The core was 49.7 kilograms per square meters (3.1 pounds per cubic feet (pcf)) aluminum honeycomb. Face-sheets were fabricated by automated tape laying 153 mm wide unidirectional tape. This work details analysis of the manufactured panels where face-sheet quality was characterized by optical microscopy, cured ply thickness measurements, acid digestion, and thermal analysis.

Regression analysis of mixed recurrent-event and panel-count data

PubMed Central

Zhu, Liang; Tong, Xinwei; Sun, Jianguo; Chen, Manhua; Srivastava, Deo Kumar; Leisenring, Wendy; Robison, Leslie L.

2014-01-01

In event history studies concerning recurrent events, two types of data have been extensively discussed. One is recurrent-event data (Cook and Lawless, 2007. The Analysis of Recurrent Event Data. New York: Springer), and the other is panel-count data (Zhao and others, 2010. Nonparametric inference based on panel-count data. Test 20, 1–42). In the former case, all study subjects are monitored continuously; thus, complete information is available for the underlying recurrent-event processes of interest. In the latter case, study subjects are monitored periodically; thus, only incomplete information is available for the processes of interest. In reality, however, a third type of data could occur in which some study subjects are monitored continuously, but others are monitored periodically. When this occurs, we have mixed recurrent-event and panel-count data. This paper discusses regression analysis of such mixed data and presents two estimation procedures for the problem. One is a maximum likelihood estimation procedure, and the other is an estimating equation procedure. The asymptotic properties of both resulting estimators of regression parameters are established. Also, the methods are applied to a set of mixed recurrent-event and panel-count data that arose from a Childhood Cancer Survivor Study and motivated this investigation. PMID:24648408

The Lateral Compressive Buckling Performance of Aluminum Honeycomb Panels for Long-Span Hollow Core Roofs

PubMed Central

Zhao, Caiqi; Zheng, Weidong; Ma, Jun; Zhao, Yangjian

2016-01-01

To solve the problem of critical buckling in the structural analysis and design of the new long-span hollow core roof architecture proposed in this paper (referred to as a “honeycomb panel structural system” (HSSS)), lateral compression tests and finite element analyses were employed in this study to examine the lateral compressive buckling performance of this new type of honeycomb panel with different length-to-thickness ratios. The results led to two main conclusions: (1) Under the experimental conditions that were used, honeycomb panels with the same planar dimensions but different thicknesses had the same compressive stiffness immediately before buckling, while the lateral compressive buckling load-bearing capacity initially increased rapidly with an increasing honeycomb core thickness and then approached the same limiting value; (2) The compressive stiffnesses of test pieces with the same thickness but different lengths were different, while the maximum lateral compressive buckling loads were very similar. Overall instability failure is prone to occur in long and flexible honeycomb panels. In addition, the errors between the lateral compressive buckling loads from the experiment and the finite element simulations are within 6%, which demonstrates the effectiveness of the nonlinear finite element analysis and provides a theoretical basis for future analysis and design for this new type of spatial structure. PMID:28773567

Validation of prescribing appropriateness criteria for older Australians using the RAND/UCLA appropriateness method

PubMed Central

Basger, Benjamin Joseph; Chen, Timothy Frank; Moles, Rebekah Jane

2012-01-01

Objective To further develop and validate previously published national prescribing appropriateness criteria to assist in identifying drug-related problems (DRPs) for commonly occurring medications and medical conditions in older (≥65 years old) Australians. Design RAND/UCLA appropriateness method. Participants A panel of medication management experts were identified consisting of geriatricians/pharmacologists, clinical pharmacists and disease management advisors to organisations that produce Australian evidence-based therapeutic publications. This resulted in a round-one panel of 15 members, and a round-two panel of 12 members. Main outcome measure Agreement on all criteria. Results Forty-eight prescribing criteria were rated. In the first rating round via email, there was disagreement regarding 17 of the criteria according to median panel ratings. During a face-to-face second round meeting, discussion resulted in retention of 25 criteria after amendments, agreement for 14 criteria with no changes required and deletion of 9 criteria. Two new criteria were added, resulting in a final validated list of 41 prescribing appropriateness criteria. Agreement after round two was reached for all 41 criteria, measured by median panel ratings and the amount of dispersion of panel ratings, based on the interpercentile range. Conclusions A set of 41 Australian prescribing appropriateness criteria were validated by an expert panel. Use of these criteria, together with clinical judgement and other medication review processes such as patient interview, is intended to assist in improving patient care by efficiently detecting potential DRPs related to commonly occurring medicines and medical conditions in older Australians. These criteria may also contribute to the medication management education of healthcare professionals. PMID:22983875

Development of a panel of genome-wide ancestry informative markers to study admixture throughout the Americas.

PubMed

Galanter, Joshua Mark; Fernandez-Lopez, Juan Carlos; Gignoux, Christopher R; Barnholtz-Sloan, Jill; Fernandez-Rozadilla, Ceres; Via, Marc; Hidalgo-Miranda, Alfredo; Contreras, Alejandra V; Figueroa, Laura Uribe; Raska, Paola; Jimenez-Sanchez, Gerardo; Zolezzi, Irma Silva; Torres, Maria; Ponte, Clara Ruiz; Ruiz, Yarimar; Salas, Antonio; Nguyen, Elizabeth; Eng, Celeste; Borjas, Lisbeth; Zabala, William; Barreto, Guillermo; González, Fernando Rondón; Ibarra, Adriana; Taboada, Patricia; Porras, Liliana; Moreno, Fabián; Bigham, Abigail; Gutierrez, Gerardo; Brutsaert, Tom; León-Velarde, Fabiola; Moore, Lorna G; Vargas, Enrique; Cruz, Miguel; Escobedo, Jorge; Rodriguez-Santana, José; Rodriguez-Cintrón, William; Chapela, Rocio; Ford, Jean G; Bustamante, Carlos; Seminara, Daniela; Shriver, Mark; Ziv, Elad; Burchard, Esteban Gonzalez; Haile, Robert; Parra, Esteban; Carracedo, Angel

2012-01-01

Most individuals throughout the Americas are admixed descendants of Native American, European, and African ancestors. Complex historical factors have resulted in varying proportions of ancestral contributions between individuals within and among ethnic groups. We developed a panel of 446 ancestry informative markers (AIMs) optimized to estimate ancestral proportions in individuals and populations throughout Latin America. We used genome-wide data from 953 individuals from diverse African, European, and Native American populations to select AIMs optimized for each of the three main continental populations that form the basis of modern Latin American populations. We selected markers on the basis of locus-specific branch length to be informative, well distributed throughout the genome, capable of being genotyped on widely available commercial platforms, and applicable throughout the Americas by minimizing within-continent heterogeneity. We then validated the panel in samples from four admixed populations by comparing ancestry estimates based on the AIMs panel to estimates based on genome-wide association study (GWAS) data. The panel provided balanced discriminatory power among the three ancestral populations and accurate estimates of individual ancestry proportions (R² > 0.9 for ancestral components with significant between-subject variance). Finally, we genotyped samples from 18 populations from Latin America using the AIMs panel and estimated variability in ancestry within and between these populations. This panel and its reference genotype information will be useful resources to explore population history of admixture in Latin America and to correct for the potential effects of population stratification in admixed samples in the region.

Development of a Panel of Genome-Wide Ancestry Informative Markers to Study Admixture Throughout the Americas

PubMed Central

Galanter, Joshua Mark; Fernandez-Lopez, Juan Carlos; Gignoux, Christopher R.; Barnholtz-Sloan, Jill; Fernandez-Rozadilla, Ceres; Via, Marc; Hidalgo-Miranda, Alfredo; Contreras, Alejandra V.; Figueroa, Laura Uribe; Raska, Paola; Jimenez-Sanchez, Gerardo; Silva Zolezzi, Irma; Torres, Maria; Ponte, Clara Ruiz; Ruiz, Yarimar; Salas, Antonio; Nguyen, Elizabeth; Eng, Celeste; Borjas, Lisbeth; Zabala, William; Barreto, Guillermo; Rondón González, Fernando; Ibarra, Adriana; Taboada, Patricia; Porras, Liliana; Moreno, Fabián; Bigham, Abigail; Gutierrez, Gerardo; Brutsaert, Tom; León-Velarde, Fabiola; Moore, Lorna G.; Vargas, Enrique; Cruz, Miguel; Escobedo, Jorge; Rodriguez-Santana, José; Rodriguez-Cintrón, William; Chapela, Rocio; Ford, Jean G.; Bustamante, Carlos; Seminara, Daniela; Shriver, Mark; Ziv, Elad; Gonzalez Burchard, Esteban; Haile, Robert

2012-01-01

Most individuals throughout the Americas are admixed descendants of Native American, European, and African ancestors. Complex historical factors have resulted in varying proportions of ancestral contributions between individuals within and among ethnic groups. We developed a panel of 446 ancestry informative markers (AIMs) optimized to estimate ancestral proportions in individuals and populations throughout Latin America. We used genome-wide data from 953 individuals from diverse African, European, and Native American populations to select AIMs optimized for each of the three main continental populations that form the basis of modern Latin American populations. We selected markers on the basis of locus-specific branch length to be informative, well distributed throughout the genome, capable of being genotyped on widely available commercial platforms, and applicable throughout the Americas by minimizing within-continent heterogeneity. We then validated the panel in samples from four admixed populations by comparing ancestry estimates based on the AIMs panel to estimates based on genome-wide association study (GWAS) data. The panel provided balanced discriminatory power among the three ancestral populations and accurate estimates of individual ancestry proportions (R2>0.9 for ancestral components with significant between-subject variance). Finally, we genotyped samples from 18 populations from Latin America using the AIMs panel and estimated variability in ancestry within and between these populations. This panel and its reference genotype information will be useful resources to explore population history of admixture in Latin America and to correct for the potential effects of population stratification in admixed samples in the region. PMID:22412386

Buckling analysis of curved composite sandwich panels subjected to inplane loadings

NASA Technical Reports Server (NTRS)

Cruz, Juan R.

1993-01-01

Composite sandwich structures are being considered for primary structure in aircraft such as subsonic and high speed civil transports. The response of sandwich structures must be understood and predictable to use such structures effectively. Buckling is one of the most important response mechanisms of sandwich structures. A simple buckling analysis is derived for sandwich structures. This analysis is limited to flat, rectangular sandwich panels loaded by uniaxial compression (N(sub x)) and having simply supported edges. In most aerospace applications, however, the structure's geometry, boundary conditions, and loading are usually very complex. Thus, a general capability for analyzing the buckling behavior of sandwich structures is needed. The present paper describes and evaluates an improved buckling analysis for cylindrically curved composite sandwich panels. This analysis includes orthotropic facesheets and first-order transverse shearing effects. Both simple support and clamped boundary conditions are also included in the analysis. The panels can be subjected to linearly varying normal loads N(sub x) and N(sub y) in addition to a constant shear load N(sub xy). The analysis is based on the modified Donnell's equations for shallow shells. The governing equations are solved by direct application of Galerkin's method. The accuracy of the present analysis is verified by comparing results with those obtained from finite element analysis for a variety of geometries, loads, and boundary conditions. The limitations of the present analysis are investigated, in particular those related to the shallow shell assumptions in the governing equations. Finally, the computational efficiency of the present analysis is considered.

78 FR 50037 - Hydrographic Services Review Panel

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-16

... pilotage, coastal and fishery management, and other disciplines as determined appropriate by the... oceanography; coastal resource management, including fisheries management and regional marine planning; and...) Describe your leadership or professional experiences which you believe will contribute to the effectiveness...

Reducing Supply Chain GHG Emissions from LCD Panel Manufacturing Webinar

EPA Pesticide Factsheets

Fluorinated greenhouse gases (F-GHGs) are among the most potent and persistent greenhouse gases contributing to global climate change. Learn about the manufacturing processes which release F-GHGs, and how LCD suppliers are working to reduce emissions.

School Expenditure and School Performance: Evidence from New South Wales Schools Using a Dynamic Panel Analysis

ERIC Educational Resources Information Center

Pugh, G.; Mangan, J.; Blackburn, V.; Radicic, D.

2015-01-01

This article estimates the effects of school expenditure on school performance in government secondary schools in New South Wales, Australia over the period 2006-2010. It uses dynamic panel analysis to exploit time series data on individual schools that only recently has become available. We find a significant but small effect of expenditure on…

Pantex Falling Man - Independent Review Panel Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bertolini, Louis; Brannon, Nathan; Olson, Jared

2014-11-01

Consolidated Nuclear Security (CNS) Pantex took the initiative to organize a Review Panel of subject matter experts to independently assess the adequacy of the Pantex Tripping Man Analysis methodology. The purpose of this report is to capture the details of the assessment including the scope, approach, results, and detailed Appendices. Along with the assessment of the analysis methodology, the panel evaluated the adequacy with which the methodology was applied as well as congruence with Department of Energy (DOE) standards 3009 and 3016. The approach included the review of relevant documentation, interactive discussion with Pantex staff, and the iterative process ofmore » evaluating critical lines of inquiry.« less

A Spatial Panel Data Analysis of Economic Growth, Urbanization, and NOx Emissions in China

PubMed Central

Ge, Xiangyu; Zhou, Yanli; Liu, Songlin

2018-01-01

Is nitrogen oxides emissions spatially correlated in a Chinese context? What is the relationship between nitrogen oxides emission levels and fast-growing economy/urbanization? More importantly, what environmental preservation and economic developing policies should China’s central and local governments take to mitigate the overall nitrogen oxides emissions and prevent severe air pollution at the provincial level in specific locations and their neighboring areas? The present study aims to tackle these issues. This is the first research that simultaneously studies the nexus between nitrogen oxides emissions and economic development/urbanization, with the application of a spatial panel data technique. Our empirical findings suggest that spatial dependence of nitrogen oxides emissions distribution exists at the provincial level. Through the investigation of the existence of an environmental Kuznets curve (EKC) embedded within the Stochastic Impacts by Regression on Population, Affluence, and Technology (STIRPAT) framework, we conclude something interesting: an inverse N-shaped EKC describes both the income-nitrogen oxides nexus and the urbanization-nitrogen oxides nexus. Some well-directed policy advice is provided to reduce nitrogen oxides in the future. Moreover, these results contribute to the literature on development and pollution. PMID:29641500

Analysis of Tumor Vessel Supply in Lewis Lung Carcinoma in Mice by Fluorescent Microsphere Distribution and Imaging with Micro- and Flat-Panel Computed Tomography

PubMed Central

Savai, Rajkumar; Wolf, Joachim C.; Greschus, Susanne; Eul, Bastian G.; Schermuly, Ralph T.; Hänze, Jörg; Voswinckel, Robert; Langheinrich, Alexander C.; Grimminger, Friedrich; Traupe, Horst; Seeger, Werner; Rose, Frank

2005-01-01

In lung carcinomas the blood supply varies depending on tumor type and stage and can develop from pulmonary or bronchial circulation, or both. To examine this in vivo, primary bronchogenic Lewis lung carcinoma cells were intratracheally instilled in C57BL/6 mice. Within 7 days, histological examinations showed progressive tumor growth at the peripheral parenchymal region. The relative contribution of tumor blood supply via the pulmonary and systemic arteries was studied in detail using fluorescent microspheres (10 μm). When compared to healthy lung parenchyma (13:1), Lewis lung carcinoma tumor tissue (52:1) showed a fourfold increase in pulmonary to systemic microspheres, indicating that the pulmonary arteries are the predominant tumor-feeding vessels. After filling the vessels with a vascular cast, the microanatomy of vessels being derived from the pulmonary artery was visualized with micro computed tomography. Flat-panel volumetric computed tomography provided longitudinal visualization of tissue bridges between the growing tumor and the pulmonary vasculature. In this model of peripheral parenchymal malignancy, new imaging techniques allowed effective visualization of lung tumor growth and vascularization in living mice, demonstrating a pulmonary blood supply for lung tumors. PMID:16192630

On the numerical investigation of sound transmission through double-walled structures with membrane-type acoustic metamaterials.

PubMed

Marinova, Polina; Lippert, Stephan; von Estorff, Otto

2017-10-01

Acoustic metamaterials appear to be of great help in the design of reliable and effective noise reduction measures in the low frequency range. The current contribution is concerned with the modeling of a low-frequency noise shield, based on a double wall arrangement, which includes membrane-type acoustic metamaterials (MAMs), considered as the most promising approach when it comes especially to the tonal noise at frequencies below 300 Hz. MAMs consist of small-sized membranes loaded with a mass. Due to their robustness and relatively simple production, MAMs have been proven to decrease the sound transmission in frequency ranges, for which poro-elastic materials have a rather negligible effect. A simulation model of a double wall panel, whose acoustic cavity is furnished with layers of metamaterials, has been developed and the sound transmission loss (STL) through the structure was calculated, using the finite element method. In order to validate the modelling approach, the STL estimation from the finite element analysis was compared to experimental measurements. The achieved results indicate a noise-decreasing possibility in tunable narrow bands as well as a broadband noise reduction for frequencies less than 300 Hz without significantly adding to the panel mass.

Influence of foreign direct investment on indicators of environmental degradation.

PubMed

Solarin, Sakiru Adebola; Al-Mulali, Usama

2018-06-21

This study aims to contribute to the existing literature by looking at the influence of foreign direct investment on carbon dioxide emissions, carbon footprint, and ecological footprint. In order to realize the aim of this study, we have utilized the augmented mean group estimator, which is supported by common correlated effect mean group estimator in the analysis for 20 countries. The panel results reveal that foreign direct investment has no effect on environmental degradation indicators. The panel results further reveal that gross domestic product, energy consumption, and urbanization are the main contributors to environmental degradation. The results at country level show that foreign direct investment and urbanization increase pollution in the developing countries while they mitigate pollution in the developed countries. Moreover, gross domestic product and energy consumption increase pollution for both developed and developing countries, which includes China and the USA. The negative impact of foreign direct investment on environmental degradation in the developed countries can be explained on the basis that these countries have strong environmental regulations, which makes it almost impossible for dirty foreign industries to invest therein. From the output of this research, several policy recommendations are enumerated for the investigated countries.

A Spatial Panel Data Analysis of Economic Growth, Urbanization, and NOx Emissions in China.

PubMed

Ge, Xiangyu; Zhou, Zhimin; Zhou, Yanli; Ye, Xinyue; Liu, Songlin

2018-04-11

Abstract : Is nitrogen oxides emissions spatially correlated in a Chinese context? What is the relationship between nitrogen oxides emission levels and fast-growing economy/urbanization? More importantly, what environmental preservation and economic developing policies should China's central and local governments take to mitigate the overall nitrogen oxides emissions and prevent severe air pollution at the provincial level in specific locations and their neighboring areas? The present study aims to tackle these issues. This is the first research that simultaneously studies the nexus between nitrogen oxides emissions and economic development/urbanization, with the application of a spatial panel data technique. Our empirical findings suggest that spatial dependence of nitrogen oxides emissions distribution exists at the provincial level. Through the investigation of the existence of an environmental Kuznets curve (EKC) embedded within the Stochastic Impacts by Regression on Population, Affluence, and Technology (STIRPAT) framework, we conclude something interesting: an inverse N-shaped EKC describes both the income-nitrogen oxides nexus and the urbanization-nitrogen oxides nexus. Some well-directed policy advice is provided to reduce nitrogen oxides in the future. Moreover, these results contribute to the literature on development and pollution.

ARC-2008-ACD08-0205-069

NASA Image and Video Library

2008-09-16

NASA's 50th Anniversay year. Panel discussion with four of NASA AMES's past center directors on how their tenure effected Ames and NASA. On the projects they pushed for and/or pushed forward and the culture of the center and the agency and how that worked for or against Ames, as well as major contributions of the time made by Ames Research Center. Panel L-R; Hans Mark, Sy Syvertson, Dale Compton, Scott Hubbard and Pete Worden, present director. (Past Directors served for periods from 1969 thru 2006) Sy Syverson posses with his portrait hanging in the hall of NASA Ames Administration Building N-200.

ARC-2008-ACD08-0205-060

NASA Image and Video Library

2008-09-16

NASA's 50th Anniversay year. Panel discussion with four of NASA AMES's past center directors on how their tenure effected Ames and NASA. On the projects they pushed for and/or pushed forward and the culture of the center and the agency and how that worked for or against Ames, as well as major contributions of the time made by Ames Research Center. Panel L-R; Hans Mark, Sy Syvertson, Dale Compton, Scott Hubbard and Pete Worden, present director. (Past Directors served for periods from 1969 thru 2006) at a round table in the Boyd Room of N-200.

Variable-intercept panel model for deformation zoning of a super-high arch dam.

PubMed

Shi, Zhongwen; Gu, Chongshi; Qin, Dong

2016-01-01

This study determines dam deformation similarity indexes based on an analysis of deformation zoning features and panel data clustering theory, with comprehensive consideration to the actual deformation law of super-high arch dams and the spatial-temporal features of dam deformation. Measurement methods of these indexes are studied. Based on the established deformation similarity criteria, the principle used to determine the number of dam deformation zones is constructed through entropy weight method. This study proposes the deformation zoning method for super-high arch dams and the implementation steps, analyzes the effect of special influencing factors of different dam zones on the deformation, introduces dummy variables that represent the special effect of dam deformation, and establishes a variable-intercept panel model for deformation zoning of super-high arch dams. Based on different patterns of the special effect in the variable-intercept panel model, two panel analysis models were established to monitor fixed and random effects of dam deformation. Hausman test method of model selection and model effectiveness assessment method are discussed. Finally, the effectiveness of established models is verified through a case study.

Efficacy of the FilmArray blood culture identification panel for direct molecular diagnosis of infectious diseases from samples other than blood.

PubMed

Micó, Miquel; Navarro, Ferran; de Miniac, Daniela; González, Yésica; Brell, Albert; López, Cristina; Sánchez-Reus, Ferran; Mirelis, Beatriz; Coll, Pere

2015-12-01

Molecular-based techniques reduce the delay in diagnosing infectious diseases and therefore contribute to better patient outcomes. We assessed the FilmArray blood culture identification (BCID) panel (Biofire Diagnostics/bioMérieux) directly on clinical specimens other than blood: cerebrospinal, joint, pleural and ascitic fluids, bronchoscopy samples and abscesses. We compared the results from 88 samples obtained by culture-based techniques. The percentage of agreement between the two methods was 75 % with a Cohen κ value of 0.51. Global sensitivity and specificity using the FilmArray BCID panel were 71 and 97 %, respectively. Sensitivity was poorer in samples with a low bacterial load, such as ascitic and pleural fluids (25 %), whereas the sensitivity for abscess samples was high (89 %). These findings suggest that the FilmArray BCID panel could be useful to perform microbiological diagnosis directly from samples other than positive blood cultures, as it offers acceptable sensitivity and moderate agreement with conventional microbiological methods. Nevertheless, cost-benefit studies should be performed before introducing this method into algorithms for microbiological diagnostics.

F-16XL Ship #2 wing glove close-up, laser cut holes, with dime for scale

NASA Technical Reports Server (NTRS)

1995-01-01

This June 1995 photograph of a test panel similiar to the one attached to the surface of an F-16XL research aircraft's left wing at NASA's Dryden Flight Research Center, Edwards, California, shows the size of the more than 10 million laser-cut holes in the panel, called a glove, as compared with a dime. Below the titanium panel into which holes are cut is a suction system linked to a compressor. During research flights with the modified, delta-winged F-16XL, the suction system pulled a small part of the boundary layer of air through the glove's porous surface to expand the extent of smooth (laminar) flow. Researchers believe that laminar flow conditions can reduce aerodynamic drag (friction) and contribute to reduced operating costs by improving fuel consumption and lowering aircraft weight. This Supersonic Laminar Flow Control (SLFC) experiment represents a collaborative effort between NASA and aerospace industry (specifically Boeing, Rockwell, and McDonnell Douglas), with Boeing assembling the panel and McDonnell Douglas designing the suction system.

Panel Discussion on Multi-Disciplinary Analysis

NASA Technical Reports Server (NTRS)

Garcia, Robert

2002-01-01

The Marshall Space Flight Center (MSFC) is hosting the Thermal and Fluids Analysis Workshop (TFAWS) during the week of September 10, 2001. Included in this year's TFAWS is a panel session on Multidisciplinary Analysis techniques. The intent is to provide an opportunity for the users to gain information as to what product may be best suited for their applications environment and to provide feedback to you, the developers, on future desired developments. Potential users of multidisciplinary analysis (MDA) techniques are often overwhelmed by the number of choices available to them via commercial products and by the pace of new developments in this area. The purpose of this panel session is to provide a forum wherein MDA tools available and under development can be discussed, compared, and contrasted. The intent of this panel is to provide the end-user with the information necessary to make educated decisions on how to proceed with selecting their MDA tool. It is anticipated that the discussions this year will focus on MDA techniques that couple discipline codes or algorithms (as opposed to monolithic, unified MDA approaches). The MDA developers will be asked to prepare a product overview presentation addressing specific questions provided by the panel organizers. The purpose of these questions will be to establish the method employed by the particular MDA technique for communication between the discipline codes, to establish the similarities and differences amongst the various approaches, and to establish the range of experience and applications for each particular MDA approach.

Religion and Sexual Identity Fluidity in a National Three-Wave Panel of U.S. Adults.

PubMed

Scheitle, Christopher P; Wolf, Julia Kay

2018-05-01

Research has shown that cross-sectional estimates of sexual identities overlook fluidity in those identities. Research has also shown that social factors, such as competing identities, can influence sexual identity fluidity. We contributed to this literature in two ways. First, we utilized a representative panel of US adults (N = 1034) surveyed in 2010, 2012, and 2014 by the General Social Survey. The addition of a third observation allowed us to examine more complexity in sexual identity fluidity. We found that 2.40% of US adults reported at least one change in sexual identity across the 4 years, with 1.59% reporting one change and 0.81% reporting two changes. Our second contribution came from examining the role of religion, as past research has suggested that religion can destabilize and prolong sexual identity development. We found that lesbian or gay individuals (N = 17), bisexuals (N = 15), and females (N = 585) showed more sexual identity fluidity compared to heterosexuals (N = 1003) and males (N = 450), respectively. Marital status, age, race, and education did not have significant associations with sexual identity fluidity. Regarding the role of religion, we found that participants identifying as more religious in Wave 1 showed more fluidity in sexual identity across later observations. Further analysis showed that higher levels of religiosity make it more likely that lesbian or gay individuals will be fluid in sexual identity, but this is not the case for heterosexual individuals. This finding reinforces past qualitative research that has suggested that religion can extend or complicate sexual minorities' identity development.

Correlation Results for a Mass Loaded Vehicle Panel Test Article Finite Element Models and Modal Survey Tests

NASA Technical Reports Server (NTRS)

Maasha, Rumaasha; Towner, Robert L.

2012-01-01

High-fidelity Finite Element Models (FEMs) were developed to support a recent test program at Marshall Space Flight Center (MSFC). The FEMs correspond to test articles used for a series of acoustic tests. Modal survey tests were used to validate the FEMs for five acoustic tests (a bare panel and four different mass-loaded panel configurations). An additional modal survey test was performed on the empty test fixture (orthogrid panel mounting fixture, between the reverb and anechoic chambers). Modal survey tests were used to test-validate the dynamic characteristics of FEMs used for acoustic test excitation. Modal survey testing and subsequent model correlation has validated the natural frequencies and mode shapes of the FEMs. The modal survey test results provide a basis for the analysis models used for acoustic loading response test and analysis comparisons

Hybrid Laminates for Application in North Conditions

NASA Astrophysics Data System (ADS)

Antipov, V. V.; Oreshko, E. I.; Erasov, V. S.; Serebrennikova, N. Yu.

2016-11-01

A hybrid aluminum-lithium alloy/SIAL laminate as a possible material for application in structures operated in North conditions is considered. The finite-element method is used for a buckling stability analysis of hybrid panels, bars, and plates. A technique allowing one to compare the buckling stability of multilayered hybrid plates is offered. Compression tests were run on a hybrid laminate wing panel as a prototype of the top panel of TU-204SM airplane made from a high-strength B95T2 aluminum alloy. It turned out that the lighter composite panel had a higher load-carrying capacity than the aluminum one. Results of investigation into the properties the hybrid aluminum-lithium alloy/SIAL laminate and an analysis of scientific-technical data on this subject showed that this composite material could be used in the elements of airframes, including those operated in north conditions.

Sensitivity Analysis of Algan/GAN High Electron Mobility Transistors to Process Variation

DTIC Science & Technology

2008-02-01

delivery system gas panel including both hydride and alkyl delivery modules and the vent/valve configurations [14...Reactor Gas Delivery Systems A basic schematic diagram of an MOCVD reactor delivery gas panel is shown in Figure 13. The reactor gas delivery...system, or gas panel , consists of a network of stainless steel tubing, automatic valves and electronic mass flow controllers (MFC). There are separate

Investigation of Collapse Characteristics of Cylindrical Composite Panels with Large Cutouts

DTIC Science & Technology

1989-12-01

COLLAPSE CHARACTERISTICS OF CYLINDRICAL COMPOSITE PANELS WITH LARGE CUTOUTS THESIS Scott A. Schimmels Captain, USAF AFIT/GAE/ENY/89D-33 Approved for...public release, distribution unlimited AFIT/GAE/ENY/89D-33 INVESTIGATION OF COLLAPSE * CHARACTERISTICS OF CYLINDRICAL COMPOSITE PANELS WITH LARGE...you would not be reading this. * This thesis research is part of an overall effort in composite nonlinear shell analysis sponsored by AFOSR, Dr

Experimental and theoretical modal analysis of full-sized wood composite panels supported on four nodes

Treesearch

Cheng Guan; Houjiang Zhang; Xiping Wang; Hu Miao; Lujing Zhou; Fenglu Liu

2017-01-01

Key elastic properties of full-sized wood composite panels (WCPs) must be accurately determined not only for safety, but also serviceability demands. In this study, the modal parameters of full-sized WCPs supported on four nodes were analyzed for determining the modulus of elasticity (E) in both major and minor axes, as well as the in-plane shear modulus of panels by...

[The relic in the Panels of São Vicente de Fora].

PubMed

Goyri-O'Neill, João; Camisão-Soares, Artur; Neves Marques, Cláudia

2013-01-01

The Panels of São Vicente de Fora, a polyptych dated from 1470 to 1480, are a work composed of 6 panels, authored by Nuno Gonçalves, a painter of King Afonso V. This work reveals one of the most remarkable collective portraits of European painting, making this polyptych an inexhaustible source of readings and interpretations, fueling a secular controversy. The present work aims analyzing precise an iconographic anatomical image repainted in the 6th panel, or the panel of the Relic. This consists of a central image within a structure shown by a red figure with special reverence. The investigation conducted and justification was based on direct observation and comparative analysis of iconographic data collected in the Museum of Antique Art. The bone pieces were selected at the Museum of Anatomy, Department of Anatomy, Faculty of Medical Sciences, New University of Lisbon, and the comparative analyses performed by two observers, with further analysis of the images obtained in the National Museum of Ancient Art using specific software. After watching these, it was concluded that this representation of a relic in the Panels of São Vicente is an iconic representation of an Occipital bone, fractured at its lower edge, being evident, almost complete, its vertical portion or scale.

Comprehensive review of the evidence regarding the effectiveness of community-based primary health care in improving maternal, neonatal and child health: 8. summary and recommendations of the Expert Panel.

PubMed

Black, Robert E; Taylor, Carl E; Arole, Shobha; Bang, Abhay; Bhutta, Zulfiqar A; Chowdhury, A Mushtaque R; Kirkwood, Betty R; Kureshy, Nazo; Lanata, Claudio F; Phillips, James F; Taylor, Mary; Victora, Cesar G; Zhu, Zonghan; Perry, Henry B

2017-06-01

The contributions that community-based primary health care (CBPHC) and engaging with communities as valued partners can make to the improvement of maternal, neonatal and child health (MNCH) is not widely appreciated. This unfortunate reality is one of the reasons why so few priority countries failed to achieve the health-related Millennium Development Goals by 2015. This article provides a summary of a series of articles about the effectiveness of CBPHC in improving MNCH and offers recommendations from an Expert Panel for strengthening CBPHC that were formulated in 2008 and have been updated on the basis of more recent evidence. An Expert Panel convened to guide the review of the effectiveness of community-based primary health care (CBPHC). The Expert Panel met in 2008 in New York City with senior UNICEF staff. In 2016, following the completion of the review, the Panel considered the review's findings and made recommendations. The review consisted of an analysis of 661 unique reports, including 583 peer-reviewed journal articles, 12 books/monographs, 4 book chapters, and 72 reports from the gray literature. The analysis consisted of 700 assessments since 39 were analyzed twice (once for an assessment of improvements in neonatal and/or child health and once for an assessment in maternal health). The Expert Panel recommends that CBPHC should be a priority for strengthening health systems, accelerating progress in achieving universal health coverage, and ending preventable child and maternal deaths. The Panel also recommends that expenditures for CBPHC be monitored against expenditures for primary health care facilities and hospitals and reflect the importance of CBPHC for averting mortality. Governments, government health programs, and NGOs should develop health systems that respect and value communities as full partners and work collaboratively with them in building and strengthening CBPHC programs - through engagement with planning, implementation (including the full use of community-level workers), and evaluation. CBPHC programs need to reach every community and household in order to achieve universal coverage of key evidence-based interventions that can be implemented in the community outside of health facilities and assure that those most in need are reached. Stronger CBPHC programs that foster community engagement/empowerment with the implementation of evidence-based interventions will be essential for achieving universal coverage of health services by 2030 (as called for by the Sustainable Development Goals recently adopted by the United Nations), ending preventable child and maternal deaths by 2030 (as called for by the World Health Organization, UNICEF, and many countries around the world), and eventually achieving Health for All as envisioned at the International Conference on Primary Health Care in 1978. Stronger CBPHC programs can also create entry points and synergies for expanding the coverage of family planning services as well as for accelerating progress in the detection and treatment of HIV/AIDS, tuberculosis, malaria, hypertension, and other chronic diseases. Continued strengthening of CBPHC programs based on rigorous ongoing operations research and evaluation will be required, and this evidence will be needed to guide national and international policies and programs.

Sensory and Physical Effects of Sugar Reduction in a Caramel Coating System.

PubMed

Mayhew, Emily J; Schmidt, Shelly J; Lee, Soo-Yeun

2017-08-01

Sugar reduction in processed foods is a pressing and complex problem, as sugars contribute important sensory and physical properties to foods. Composed of sugars and lipids, caramel coating systems, like the coating in caramel popcorns, exemplify this challenge. In order to probe the feasibility and consequences of sugar reduction, both sensory and physical properties were measured for 3 types of caramel coating systems. Four commonly used sugar alcohols, isomalt, maltitol, mannitol, and sorbitol, with different thermal properties and relative sweetness values were chosen to replace sugar in the caramel coating systems at 25% and 50% sugar reduction levels. Full sugar (control) and reduced sugar caramel coating samples were prepared in duplicate. Ten trained panelists participated in a 6-wk descriptive analysis panel to define and quantify the intensity of important sensory characteristics. All 24 sensory terms generated by the panel differed significantly across caramel type and sugar replacer. Thermal properties were measured through differential scanning calorimetry, and textural properties were measured through texture profile analysis. Replacement of sugar with sugar alcohols was found to decrease the glass transition temperature and systematically alter the hardness and resilience of caramel samples. Principal component analysis of sensory and physical data revealed that caramel coating type dictates caramel aroma, aroma by mouth, taste, and aftertaste, while sugar replacer and replacement level dictate texture. This research represents the first comprehensive study of the effects of sugar reduction in a caramel coating system and suggests successful strategies for sugar reduction and key parameters to control in reduced sugar systems. © 2017 Institute of Food Technologists®.

Effects of eccentricities and lateral pressure on the design of stiffened compression panels

NASA Technical Reports Server (NTRS)

Giles, G. L.; Anderson, M. S.

1972-01-01

An analysis for determining the effects of eccentricities and lateral pressure on the design of stiffened compression panels is presented. The four types of panel stiffeners considered are integral, zee, integral zee, and integral tee. Mass-strength curves, which give the mass of the panel necessary to carry a specified load, are given along with related design equations needed to calculate the cross-sectional dimensions of the minimum-mass-stiffened panel. The results of the study indicate that the proportions of the panels are geometrically similar to the proportions of panels designed for no eccentricity or lateral pressure, but no cross-sectional dimensions are greater, resulting in significantly increased mass. The analytical minimum-mass designs of zee-stiffened panels are compared with designs from experimentally derived charts. An assumed eccentricity of 0.001 times the length of the panel is used to correlate the analytical and experimental data. Good correlation between the experimentally derived and the analytical curves is obtained for the range of loading where materials yield governs the design. At lower loads the mass given by the analytical curve using this assumed eccentricity is greater than that given by the experimental results.

Comparative analysis of heat dissipation panels for a hybrid cooling system integrated in buildings

NASA Astrophysics Data System (ADS)

Zuazua-Ros, A.; Ramos, JC; Martín-Gómez, C.; Gómez-Acebo, Tomás; Pisano, A.

2018-05-01

The use of cooling panels as heat dissipation elements integrated in buildings has been previously investigated by the authors. Those elements would be connected to the condenser and would dissipate the heat in a passive form. Following the research, this study analyses and compares the thermal performance of two heat dissipation panels as part of a hybrid cooling system. Both panels were experimentally tested under different variables, thus having nine scenarios for each panel. Additionally, an already validated model was applied. The empirical results show a considerable difference between the cooling capacity among them, doubling the daily average ratio in one scenario. The heat dissipation ratios vary between 106 and 227 W/m2 in the first case and 140 and 413 W/m2 in the second. Regarding the model applicability, the average error for each panel was 4.0% and 8.5%. The bond between the metal sheet and the pipes of the panels has proven to be the main parameter to assure the highest heat dissipation potential of each panel.

Space Shuttle Orbiter Wing-Leading-Edge Panel Thermo-Mechanical Analysis for Entry Conditions

NASA Technical Reports Server (NTRS)

Knight, Norman F., Jr.; Song, Kyongchan; Raju, Ivatury S.

2010-01-01

Linear elastic, thermo-mechanical stress analyses of the Space Shuttle Orbiter wing-leading-edge panels is presented for entry heating conditions. The wing-leading-edge panels are made from reinforced carbon-carbon and serve as a part of the overall thermal protection system. Three-dimensional finite element models are described for three configurations: integrated configuration, an independent single-panel configuration, and a local lower-apex joggle segment. Entry temperature conditions are imposed and the through-the-thickness response is examined. From the integrated model, it was concluded that individual panels can be analyzed independently since minimal interaction between adjacent components occurred. From the independent single-panel model, it was concluded that increased through-the-thickness stress levels developed all along the chord of a panel s slip-side joggle region, and hence isolated local joggle sections will exhibit the same trend. From the local joggle models, it was concluded that two-dimensional plane-strain models can be used to study the influence of subsurface defects along the slip-side joggle region of these panels.

Flight Test of a Technology Transparent Light Concentration Panel on SMEX/WIRE

NASA Technical Reports Server (NTRS)

Stern, Theodore G.; Lyons, John

2000-01-01

A flight experiment has demonstrated a modular solar concentrator that can be used as a direct substitute replacement for planar photovoltaic panels in spacecraft solar arrays. The Light Concentrating Panel (LCP) uses an orthogrid arrangement of composite mirror strips to form an array of rectangular mirror troughs that reflect light onto standard, high-efficiency solar cells at a concentration ratio of approximately 3:1. The panel area, mass, thickness, and pointing tolerance has been shown to be similar to a planar array using the same cells. Concentration reduces the panel's cell area by 2/3, which significantly reduces the cost of the panel. An opportunity for a flight experiment module arose on NASA's Small Explorer / Wide-Field Infrared Explorer (SMEX/WIRE) spacecraft, which uses modular solar panel modules integrated into a solar panel frame structure. The design and analysis that supported implementation of the LCP as a flight experiment module is described. Easy integration into the existing SMEX-LITE wing demonstrated the benefits of technology transparency. Flight data shows the stability of the LCP module after nearly one year in Low Earth Orbit.

Graft Polymerization of Acrylic Acid on a Polytetrafluoroethylene Panel by an Inductively Coupled Plasma

NASA Astrophysics Data System (ADS)

Lan, Yan; You, Qingliang; Cheng, Cheng; Zhang, Suzhen; Ni, Guohua; Nagatsu, M.; Meng, Yuedong

2011-02-01

Surface modification on a polytetrafluoroethylene (PTFE) panel was performed with sequential nitrogen plasma treatments and surface-initiated polymerization. By introducing COO- groups to the surface of the PTFE panel through grafting polymerization of acrylic acid (AA), a transparent poly (acrylic acid) (PAA) membrane was achieved from acrylic acid solution. Grafting polymerization initiating from the active groups was achieved on the PTFE panel surface after the nitrogen plasma treatment. Utilizing the acrylic acid as monomers, with COO- groups as cross link sites to form reticulation structure, a transparent poly (acrylic acid) membrane with arborescent macromolecular structure was formed on the PTFE panel surface. Analysis methods, such as fourier transform infrared spectroscopy (FTIR), microscopy and X-ray photoelectron spectroscopy (XPS), were utilized to characterize the structures of the macromolecule membrane on the PTFE panel surface. A contact angle measurement was performed to characterize the modified PTFE panels. The surface hydrophilicities of modified PTFE panels were significantly enhanced after the plasma treatment. It was shown that the grafting rate is related to the treating time and the power of plasma.

Development of Electrostatically Clean Solar Array Panels

NASA Technical Reports Server (NTRS)

Stern, Theodore G.

2000-01-01

Certain missions require Electrostatically Clean Solar Array (ECSA) panels to establish a favorable environment for the operation of sensitive scientific instruments. The objective of this program was to demonstrate the feasibility of an ECSA panel that minimizes panel surface potential below 100mV in LEO and GEO charged particle environments, prevents exposure of solar cell voltage and panel insulating surfaces to the ambient environment, and provides an equipotential, grounded structure surrounding the entire panel. An ECSA panel design was developed that uses a Front Side Aperture-Shield (FSA) that covers all inter-cell areas with a single graphite composite laminate, composite edge clips for connecting the FSA to the panel substrate, and built-in tabs that interconnect the FSA to conductive coated coverglasses using a conductive adhesive. Analysis indicated the ability of the design to meet the ECSA requirements. Qualification coupons and a 0.5m x 0.5m prototype panel were fabricated and tested for photovoltaic performance and electrical grounding before and after exposure to acoustic and thermal cycling environments. The results show the feasibility of achieving electrostatic cleanliness with a small penalty in mass, photovoltaic performance and cost, with a design is structurally robust and compatible with a wide range of current solar panel technologies.

Structural efficiency studies of corrugated compression panels with curved caps and beaded webs

NASA Technical Reports Server (NTRS)

Davis, R. C.; Mills, C. T.; Prabhakaran, R.; Jackson, L. R.

1984-01-01

Curved cross-sectional elements are employed in structural concepts for minimum-mass compression panels. Corrugated panel concepts with curved caps and beaded webs are optimized by using a nonlinear mathematical programming procedure and a rigorous buckling analysis. These panel geometries are shown to have superior structural efficiencies compared with known concepts published in the literature. Fabrication of these efficient corrugation concepts became possible by advances made in the art of superplastically forming of metals. Results of the mass optimization studies of the concepts are presented as structural efficiency charts for axial compression.

Impact damage and residual strength analysis of composite panels with bonded stiffeners. [for primary aircraft structures

NASA Technical Reports Server (NTRS)

Madan, Ram C.; Shuart, Mark J.

1990-01-01

Blade-stiffened, compression-loaded cover panels were designed, manufactured, analyzed, and tested. All panels were fabricated from IM6/1808I interleafed graphite-epoxy. An orthotropic blade stiffener and an orthotropic skin were selected to satisfy the design requirements for an advanced aircraft configuration. All specimens were impact damaged prior to testing. Experimental results were obtained for three- and five-stiffener panels. Analytical results described interlaminar forces caused by impact and predicted specimen residual strength. The analytical results compared reasonably with the experimental results for residual strength of the specimens.

Buckling Analysis of Anisotropic Curved Panels and Shells with Variable Curvature

NASA Technical Reports Server (NTRS)

Jaunky, Navin; Knight, Norman F., Jr.; Ambur, Damodar R.

1998-01-01

A buckling formulation for anisotropic curved panels with variable curvature is presented in this paper. The variable curvature panel is assumed to consists of two or more panels of constant but different curvatures. Bezier functions are used as Ritz functions Displacement (C(sup 0)), and slope (C(sup 1)) continuities between segments are imposed by manipulation of the Bezier control points. A first-order shear-deformation theory is used in the buckling formulation. Results obtained from the present formulation are compared with those from finite element simulations and are found to be in good agreement.

Optimization of composite sandwich cover panels subjected to compressive loadings

NASA Technical Reports Server (NTRS)

Cruz, Juan R.

1991-01-01

An analysis and design method is presented for the design of composite sandwich cover panels that includes transverse shear effects and damage tolerance considerations. This method is incorporated into an optimization program called SANDOP (SANDwich OPtimization). SANDOP is used in the present study to design optimized composite sandwich cover panels for transport aircraft wing applications as a demonstration of its capabilities. The results of this design study indicate that optimized composite sandwich cover panels have approximately the same structural efficiency as stiffened composite cover panels designed to identical constraints. Results indicate that inplane stiffness requirements have a large effect on the weight of these composite sandwich cover panels at higher load levels. Increasing the maximum allowable strain and the upper percentage limit of the 0 degree and plus or minus 45 degree plies can yield significant weight savings. The results show that the structural efficiency of these optimized composite sandwich cover panels is relatively insensitive to changes in core density.

Design and analysis of grid stiffened fuselage panel with curved stiffeners

NASA Astrophysics Data System (ADS)

Hemanth, Bharath; Babu, N. C. Mahendra; Shivakumar, H. G.; Srikari, S.

2018-04-01

Designing and analyzing grid stiffened panel to understand the effect of stiffeners on stiffness of the panel is crucial in designing grid stiffened cylinder for fuselage application. Traditionally only straight stiffeners were used due to limited manufacturing capabilities and in recent years GSS with curved stiffeners have become a reality. The present work is on flat grid stiffened panel and the focus is to realize the change in stiffness by converting straight stiffeners in an isogrid panel to curved stiffeners. An isogrid stiffened panel is identified from literature for which experimental results were available and was considered for replacing straight stiffeners with curved stiffeners. Defining and designing the curve for curved stiffeners which can be used to replace straight stiffeners in isogrid pattern is crucial. FE model of the grid stiffened fuselage panel with isogrid pattern identified from the literature for which experimental data was available was developed and evaluated for stiffness. For the same panel, curved grid pattern to enhance stiffness of the panel was designed following existing design procedure. FE model of the grid stiffened fuselage panel with designed curved stiffeners was developed and evaluated for stiffness. It is established that the stiffness of panel can be increased by minimum of 2.82% to maximum of 11.93% by using curved stiffeners of particular curvature as a replacement for straight stiffeners in isogrid pattern with a slight mass penalty.

Mechanical and thermal buckling analysis of rectangular sandwich panels under different edge conditions

NASA Technical Reports Server (NTRS)

Ko, William L.

1994-01-01

The combined load (mechanical or thermal load) buckling equations were established for orthotropic rectangular sandwich panels under four different edge conditions by using the Rayleigh-Ritz method of minimizing the total potential energy of a structural system. Two-dimensional buckling interaction curves and three-dimensional buckling interaction surfaces were constructed for high-temperature honeycomb-core sandwich panels supported under four different edge conditions. The interaction surfaces provide overall comparison of the panel buckling strengths and the domains of symmetrical and antisymmetrical buckling associated with the different edge conditions. In addition, thermal buckling curves of these sandwich panels are presented. The thermal buckling conditions for the cases with and without thermal moments were found to be identical for the small deformation theory.

Quantification of selected aroma-active compounds in strawberries by headspace solid-phase microextraction gas chromatography and correlation with sensory descriptive analysis.

PubMed

Jetti, R R; Yang, E; Kurnianta, A; Finn, C; Qian, M C

2007-09-01

Selected aroma-active compounds in strawberries were quantified using headspace solid-phase microextraction and gas chromatography. Ten strawberry cultivars grown in California and Oregon were studied. The standard curves were built in a synthetic matrix and quantification was achieved using multiple internal standards. Odor activity values (OAVs) of the aroma compounds were calculated to understand their contribution to the overall aroma. Although the concentrations of the aroma compounds varied depending on the cultivars, in general, ethyl butanoate, mesifurane, ethyl hexanoate, ethyl 3-methylbutanoate, hexyl acetate, and gamma-dodecalactone had the highest OAVs. Descriptive sensory analysis was performed by a trained panel of 10 members. A PCA plot was built to understand the aroma contribution of principal components. The chemical results were compared with sensory data. The OAV of esters correlated well with the floral, pineapple, and banana notes. The green notes did not correlate with the concentration or OAVs of aldehydes or C6 alcohols. It is assumed that the higher amounts of green, sulfur, musty, and waxy notes in some cultivars were due to the lack of fruity notes.

Sensors Workshop summary report

NASA Technical Reports Server (NTRS)

1977-01-01

A review of the efforts of three workshops is presented. The presentation describes those technological developments that would contribute most to sensor subsystem optimization and improvement of NASA's data acquisition capabilities, and summarizes the recommendations of the sensor technology panels from the most recent workshops.

How to model a negligible probability under the WTO sanitary and phytosanitary agreement?

PubMed

Powell, Mark R

2013-06-01

Since the 1997 EC--Hormones decision, World Trade Organization (WTO) Dispute Settlement Panels have wrestled with the question of what constitutes a negligible risk under the Sanitary and Phytosanitary Agreement. More recently, the 2010 WTO Australia--Apples Panel focused considerable attention on the appropriate quantitative model for a negligible probability in a risk assessment. The 2006 Australian Import Risk Analysis for Apples from New Zealand translated narrative probability statements into quantitative ranges. The uncertainty about a "negligible" probability was characterized as a uniform distribution with a minimum value of zero and a maximum value of 10(-6) . The Australia - Apples Panel found that the use of this distribution would tend to overestimate the likelihood of "negligible" events and indicated that a triangular distribution with a most probable value of zero and a maximum value of 10⁻⁶ would correct the bias. The Panel observed that the midpoint of the uniform distribution is 5 × 10⁻⁷ but did not consider that the triangular distribution has an expected value of 3.3 × 10⁻⁷. Therefore, if this triangular distribution is the appropriate correction, the magnitude of the bias found by the Panel appears modest. The Panel's detailed critique of the Australian risk assessment, and the conclusions of the WTO Appellate Body about the materiality of flaws found by the Panel, may have important implications for the standard of review for risk assessments under the WTO SPS Agreement. © 2012 Society for Risk Analysis.

Large Deployable Reflector (LDR) thermal characteristics

NASA Technical Reports Server (NTRS)

Miyake, R. N.; Wu, Y. C.

1988-01-01

The thermal support group, which is part of the lightweight composite reflector panel program, developed thermal test and analysis evaluation tools necessary to support the integrated interdisciplinary analysis (IIDA) capability. A detailed thermal mathematical model and a simplified spacecraft thermal math model were written. These models determine the orbital temperature level and variation, and the thermally induced gradients through and across a panel, for inclusion in the IIDA.

Florida, 2010 forest inventory and analysis factsheet

Treesearch

Mark J. Brown; Jarek Nowak

2012-01-01

Forest Inventory and Analysis (FIA) factsheets are produced periodically to keep the public up to date on the extent and condition of the forest lands in each State. This factsheet is an annualized update of the full 5-year cycle of panel data completed in 2007 and updated by reprocessing with new 2009 and 2010 panel data. It represents 5 years of data, 40 percent of...

Advances in Structural Integrity Analysis Methods for Aging Metallic Airframe Structures with Local Damage

NASA Technical Reports Server (NTRS)

Starnes, James H., Jr.; Newman, James C., Jr.; Harris, Charles E.; Piascik, Robert S.; Young, Richard D.; Rose, Cheryl A.

2003-01-01

Analysis methodologies for predicting fatigue-crack growth from rivet holes in panels subjected to cyclic loads and for predicting the residual strength of aluminum fuselage structures with cracks and subjected to combined internal pressure and mechanical loads are described. The fatigue-crack growth analysis methodology is based on small-crack theory and a plasticity induced crack-closure model, and the effect of a corrosive environment on crack-growth rate is included. The residual strength analysis methodology is based on the critical crack-tip-opening-angle fracture criterion that characterizes the fracture behavior of a material of interest, and a geometric and material nonlinear finite element shell analysis code that performs the structural analysis of the fuselage structure of interest. The methodologies have been verified experimentally for structures ranging from laboratory coupons to full-scale structural components. Analytical and experimental results based on these methodologies are described and compared for laboratory coupons and flat panels, small-scale pressurized shells, and full-scale curved stiffened panels. The residual strength analysis methodology is sufficiently general to include the effects of multiple-site damage on structural behavior.

Nontargeted metabolite profiles and sensory properties of strawberry cultivars grown both organically and conventionally.

PubMed

Kårlund, Anna; Hanhineva, Kati; Lehtonen, Marko; Karjalainen, Reijo O; Sandell, Mari

2015-01-28

Strawberry (Fragaria × ananassa Duch.) contains many secondary metabolites potentially beneficial for human health, and several of these compounds contribute to strawberry sensory properties, as well. In this study, three strawberry cultivars grown both conventionally and organically were subjected to nontargeted metabolite profiling analysis with LC-qTOF-ESI-MS and to descriptive sensory evaluation by a trained panel. Combined metabolome and sensory data (PLS model) revealed that 79% variation in the metabolome explained 88% variation in the sensory profiles. Flavonoids and condensed and hydrolyzable tannins determined the orosensory properties, and fatty acids contributed to the odor attributes of strawberry. Overall, the results indicated that the chemical composition and sensory quality of strawberries grown in different cultivation systems vary mostly according to cultivar. Organic farming practices may enhance the accumulation of some plant metabolites in specific strawberry genotypes. Careful cultivar selection is a key factor for the improvement of nutritional quality and marketing value of organic strawberries.

A rapid screening of ancestry for genetic association studies in an admixed population from Pernambuco, Brazil.

PubMed

Coelho, A V C; Moura, R R; Cavalcanti, C A J; Guimarães, R L; Sandrin-Garcia, P; Crovella, S; Brandão, L A C

2015-03-31

Genetic association studies determine how genes influence traits. However, non-detected population substructure may bias the analysis, resulting in spurious results. One method to detect substructure is to genotype ancestry informative markers (AIMs) besides the candidate variants, quantifying how much ancestral populations contribute to the samples' genetic background. The present study aimed to use a minimum quantity of markers, while retaining full potential to estimate ancestries. We tested the feasibility of a subset of the 12 most informative markers from a previously established study to estimate influence from three ancestral populations: European, African and Amerindian. The results showed that in a sample with a diverse ethnicity (N = 822) derived from 1000 Genomes database, the 12 AIMs had the same capacity to estimate ancestries when compared to the original set of 128 AIMs, since estimates from the two panels were closely correlated. Thus, these 12 SNPs were used to estimate ancestry in a new sample (N = 192) from an admixed population in Recife, Northeast Brazil. The ancestry estimates from Recife subjects were in accordance with previous studies, showing that Northeastern Brazilian populations show great influence from European ancestry (59.7%), followed by African (23.0%) and Amerindian (17.3%) ancestries. Ethnicity self-classification according to skin-color was confirmed to be a poor indicator of population substructure in Brazilians, since ancestry estimates overlapped between classifications. Thus, our streamlined panel of 12 markers may substitute panels with more markers, while retaining the capacity to control for population substructure and admixture, thereby reducing sample processing time.

Succession and seasonal variation in epilithic biofilms on artificial reefs in culture waters of the sea cucumber Apostichopus japonicus

NASA Astrophysics Data System (ADS)

Liu, Liming; Du, Rongbin; Zhang, Xiaoling; Dong, Shuanglin; Sun, Shichun

2017-01-01

Periphytic biofilms in aquaculture waters are thought to improve water quality, provide an additional food source, and improve the survival and growth of some reared animals. In the Asia- Pacific region, particularly in China, artificial reefs are commonly used in the commercial farming of sea cucumbers. However, few studies have examined the epilithic biofilms on the artificial reefs. To gain a better understanding of the succession of epilithic biofilms and their ecological processes in sea cucumber culture waters, two experiments were conducted in culture waters of the sea cucumber Apostichopus japonicus in Rongcheng, China, using artificial test panels. On the test panels of succession experiment, more than 67 species were identified in the biofilms. On the test panels of seasonal variation experiment, more than 46 species were recorded in the biofilms. In both experiments, communities of epilithic biofilms were dominated by diatoms, green algae and the annelid Spirorbis sp. In the initial colonization, the dominant diatoms were Cocconeis sp., Amphora spp. and Nitzschia closterium in June, which were succeeded by species of Navicula, Cocconeis and Nitzschia (July to September), and then by Licmophora abbreviata, Nitzschia closterium and Synedra spp. in the following months. A diatom bloom in the autumn and filamentous green algae burst in the summer were also observed. Ecological indices well annotated the succession and seasonal changes in epilithic communities. Multidimensional scaling (MDS) analysis found significant differences in diatom community composition among months and seasons. Fast growth of biofilms was observed in the summer and autumn, whereas the biomass of summer biofilms was largely made up of filamentous green algae. Present results show that the components of epilithic biofilms are mostly optimal foods of A. japonicus, suggesting that biofilms on artificial reefs may contribute important nutritional sources for sea cucumbers during their growth seasons. Future works should include quantitative determination of the contribution of epilithic biofilms to the diet of A. japonicus, potential roles of epilithic biofilms in regulating the water quality of sea cucumber ponds, and the regulation of epilithic biofilms in sea cucumber culture ponds.

Behavior of composite sandwich panels with several core designs at different impact velocities

NASA Astrophysics Data System (ADS)

Jiga, Gabriel; Stamin, Ştefan; Dinu, Gabriela

2018-02-01

A sandwich composite represents a special class of composite materials that is manufactured by bonding two thin but stiff faces to a low density and low strength but thick core. The distance between the skins given by the core increases the flexural modulus of the panel with a low mass increase, producing an efficient structure able to resist at flexural and buckling loads. The strength of sandwich panels depends on the size of the panel, skins material and number or density of the cells within it. Sandwich composites are used widely in several industries, such as aerospace, automotive, medical and leisure industries. The behavior of composite sandwich panels with different core designs under different impact velocities are analyzed in this paper by numerical simulations performed on sandwich panels. The modeling was done in ANSYS and the analysis was performed through LS-DYNA.

A novel heuristic for optimization aggregate production problem: Evidence from flat panel display in Malaysia

NASA Astrophysics Data System (ADS)

Al-Kuhali, K.; Hussain M., I.; Zain Z., M.; Mullenix, P.

2015-05-01

Aim: This paper contribute to the flat panel display industry it terms of aggregate production planning. Methodology: For the minimization cost of total production of LCD manufacturing, a linear programming was applied. The decision variables are general production costs, additional cost incurred for overtime production, additional cost incurred for subcontracting, inventory carrying cost, backorder costs and adjustments for changes incurred within labour levels. Model has been developed considering a manufacturer having several product types, which the maximum types are N, along a total time period of T. Results: Industrial case study based on Malaysia is presented to test and to validate the developed linear programming model for aggregate production planning. Conclusion: The model development is fit under stable environment conditions. Overall it can be recommended to adapt the proven linear programming model to production planning of Malaysian flat panel display industry.

A Qualitative Evaluation of Ethics Educational Program in Health Science1

PubMed Central

Ekmekci, Perihan Elif; Oral, Murat; Yurdakul, Eray Serdar

2015-01-01

This paper originates from a panel discussion on the evaluation of “Ethics Educational Program in Health Sciences” held during the IAEE Conference 2014 Ankara, Turkey. The participants of the panel had consultations to solidify the concepts about the topic. The qualitative data out of these antecedent discussions became mature with the contributions in the panel. The outcome of this qualitative study mainly focuses on the examples of two current curricula; one from PhD on History of Medicine and Medical Ethics, the other one from an elective course on medical ethics as a part of a PhD program on Pharmacy Management and History, followed by the major challenges the trainees face during their education, their expectations and whether the program was satisfactory, the aspects of the programs which are prone to improvement and their overall evaluations of the programs. PMID:26664129

Minutes of the third annual meeting of the Panel on Reference Nuclear Data. [BNL, October 5, 1978

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burrows, T.W.; Stewart, L.; Coyne, J.J.

1979-05-01

The major activities of the meeting were as follows: welcome; organization, approval of minutes of the second meeting, and approval of agenda; review of nuclear data compilation and evaluation efforts (national and international efforts, master data files, publications); summary of 1977 panel meeting; definition of reference nuclear data; discussion of specific data needs and possible data center contributions (reactor physics, medicine and biology, controlled thermonuclear reactors and astrophysics); establishment of current interest and future direction of the panel; adjournment. Recommendations and action items are listed. Tables on nuclear data needs in applied physics, medicine and biology, and controlled thermonuclear reactorsmore » and astrophysics are presented. Appendixes include membership lists of various committees, summaries of publication activities, survey results, correspondence, and portions of the documents Proceedings of the Magnetic Fusion Energy Blanket and Shield Workshop and National Needs for Critically Evaluated Physical and Chemical Data. (RWR)« less

Residual Strength Analyses of Monolithic Structures

NASA Technical Reports Server (NTRS)

Forth, Scott (Technical Monitor); Ambur, Damodar R. (Technical Monitor); Seshadri, B. R.; Tiwari, S. N.

2003-01-01

Finite-element fracture simulation methodology predicts the residual strength of damaged aircraft structures. The methodology uses the critical crack-tip-opening-angle (CTOA) fracture criterion to characterize the fracture behavior of the material. The CTOA fracture criterion assumes that stable crack growth occurs when the crack-tip angle reaches a constant critical value. The use of the CTOA criterion requires an elastic- plastic, finite-element analysis. The critical CTOA value is determined by simulating fracture behavior in laboratory specimens, such as a compact specimen, to obtain the angle that best fits the observed test behavior. The critical CTOA value appears to be independent of loading, crack length, and in-plane dimensions. However, it is a function of material thickness and local crack-front constraint. Modeling the local constraint requires either a three-dimensional analysis or a two-dimensional analysis with an approximation to account for the constraint effects. In recent times as the aircraft industry is leaning towards monolithic structures with the intention of reducing part count and manufacturing cost, there has been a consistent effort at NASA Langley to extend critical CTOA based numerical methodology in the analysis of integrally-stiffened panels.In this regard, a series of fracture tests were conducted on both flat and curved aluminum alloy integrally-stiffened panels. These flat panels were subjected to uniaxial tension and during the test, applied load-crack extension, out-of-plane displacements and local deformations around the crack tip region were measured. Compact and middle-crack tension specimens were tested to determine the critical angle (wc) using three-dimensional code (ZIP3D) and the plane-strain core height (hJ using two-dimensional code (STAGS). These values were then used in the STAGS analysis to predict the fracture behavior of the integrally-stiffened panels. The analyses modeled stable tearing, buckling, and crack branching at the integral stiffener using different values of critical CTOA for different material thicknesses and orientation. Comparisons were made between measured and predicted load-crack extension, out-of-plane displacements and local deformations around the crack tip region. Simultaneously, three-dimensional capabilities to model crack branching and to monitor stable crack growth of multiple cracks in a large thick integrally-stiffened flat panels were implemented in three-dimensional finite element code (ZIP3D) and tested by analyzing the integrally-stiffened panels tested at Alcoa. The residual strength of the panels predicted from STAGS and ZP3D code compared very well with experimental data. In recent times, STAGS software has been updated with new features and now one can have combinations of solid and shell elements in the residual strength analysis of integrally-stiffened panels.

Analysis of the Contribution of Hemocytes and Autophagy to Drosophila Antiviral Immunity.

PubMed

Lamiable, Olivier; Arnold, Johan; de Faria, Isaque Joao da Silva; Olmo, Roenick Proveti; Bergami, Francesco; Meignin, Carine; Hoffmann, Jules A; Marques, Joao Trindade; Imler, Jean-Luc

2016-06-01

Antiviral immunity in the model organism Drosophila melanogaster involves the broadly active intrinsic mechanism of RNA interference (RNAi) and virus-specific inducible responses. Here, using a panel of six viruses, we investigated the role of hemocytes and autophagy in the control of viral infections. Injection of latex beads to saturate phagocytosis, or genetic depletion of hemocytes, resulted in decreased survival and increased viral titers following infection with Cricket paralysis virus (CrPV), Flock House virus (FHV), and vesicular stomatitis virus (VSV) but had no impact on Drosophila C virus (DCV), Sindbis virus (SINV), and Invertebrate iridescent virus 6 (IIV6) infection. In the cases of CrPV and FHV, apoptosis was induced in infected cells, which were phagocytosed by hemocytes. In contrast, VSV did not trigger any significant apoptosis but we confirmed that the autophagy gene Atg7 was required for full virus resistance, suggesting that hemocytes use autophagy to recognize the virus. However, this recognition does not depend on the Toll-7 receptor. Autophagy had no impact on DCV, CrPV, SINV, or IIV6 infection and was required for replication of the sixth virus, FHV. Even in the case of VSV, the increases in titers were modest in Atg7 mutant flies, suggesting that autophagy does not play a major role in antiviral immunity in Drosophila Altogether, our results indicate that, while autophagy plays a minor role, phagocytosis contributes to virus-specific immune responses in insects. Phagocytosis and autophagy are two cellular processes that involve lysosomal degradation and participate in Drosophila immunity. Using a panel of RNA and DNA viruses, we have addressed the contribution of phagocytosis and autophagy in the control of viral infections in this model organism. We show that, while autophagy plays a minor role, phagocytosis contributes to virus-specific immune responses in Drosophila This work brings to the front a novel facet of antiviral host defense in insects, which may have relevance in the control of virus transmission by vector insects or in the resistance of beneficial insects to viral pathogens. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Analysis of the Contribution of Hemocytes and Autophagy to Drosophila Antiviral Immunity

PubMed Central

Lamiable, Olivier; Arnold, Johan; de Faria, Isaque Joao da Silva; Olmo, Roenick Proveti; Bergami, Francesco; Meignin, Carine; Hoffmann, Jules A.; Marques, Joao Trindade

2016-01-01

ABSTRACT Antiviral immunity in the model organism Drosophila melanogaster involves the broadly active intrinsic mechanism of RNA interference (RNAi) and virus-specific inducible responses. Here, using a panel of six viruses, we investigated the role of hemocytes and autophagy in the control of viral infections. Injection of latex beads to saturate phagocytosis, or genetic depletion of hemocytes, resulted in decreased survival and increased viral titers following infection with Cricket paralysis virus (CrPV), Flock House virus (FHV), and vesicular stomatitis virus (VSV) but had no impact on Drosophila C virus (DCV), Sindbis virus (SINV), and Invertebrate iridescent virus 6 (IIV6) infection. In the cases of CrPV and FHV, apoptosis was induced in infected cells, which were phagocytosed by hemocytes. In contrast, VSV did not trigger any significant apoptosis but we confirmed that the autophagy gene Atg7 was required for full virus resistance, suggesting that hemocytes use autophagy to recognize the virus. However, this recognition does not depend on the Toll-7 receptor. Autophagy had no impact on DCV, CrPV, SINV, or IIV6 infection and was required for replication of the sixth virus, FHV. Even in the case of VSV, the increases in titers were modest in Atg7 mutant flies, suggesting that autophagy does not play a major role in antiviral immunity in Drosophila. Altogether, our results indicate that, while autophagy plays a minor role, phagocytosis contributes to virus-specific immune responses in insects. IMPORTANCE Phagocytosis and autophagy are two cellular processes that involve lysosomal degradation and participate in Drosophila immunity. Using a panel of RNA and DNA viruses, we have addressed the contribution of phagocytosis and autophagy in the control of viral infections in this model organism. We show that, while autophagy plays a minor role, phagocytosis contributes to virus-specific immune responses in Drosophila. This work brings to the front a novel facet of antiviral host defense in insects, which may have relevance in the control of virus transmission by vector insects or in the resistance of beneficial insects to viral pathogens. PMID:27009948

Jobs and the resource curse in the sun: The effects of oil production on female labor force participation in California counties from 1980-2010

NASA Astrophysics Data System (ADS)

Zavala, Gabriel

This study aims to evaluate the relationship between oil income and the female labor force participation rate in California for the years of 1980, 1990, 2000 and 2010 using panel linear regression models. This study also aims to visualize the spatial patterns of both variables in California through Hot Spot analysis at the county level for the same years. The regression found no sign of a relationship between oil income and female labor force participation rate but did find evidence of a positive relationship between two income control variables and the female labor force participation rate. The hot spot analysis also found that female labor force participation cold spots are not spatially correlated with oil production hot spots. These findings contribute new methodologies at a finer scale to the very nuanced discussion of the resource curse in the United States.

The coordination of plural logics of action and its consequences: Evidence from plural medical systems

PubMed Central

Shim, Jae-Mahn

2017-01-01

Drawing on the theory of social action in organizational and institutional sociology, this paper examines the behavioral consequences of plural logics of action. It addresses the question based on the empirical case of plural medical systems that are composed of both biomedicine and alternative medicine. Applying mixed methods of a cross-national panel data analysis and a content analysis of medical journal articles, it finds that plural systems affect health outcomes negatively when tensions between biomedicine and alternative medicine are unaddressed. In contrast, plural systems produce tangible health benefits when biomedicine and alternative medicine are coordinated through government policies or by health care organizations/professionals. This paper proposes plurality coordination as an important mechanism that modifies the behavioral consequences of plural logics. This proposition contributes to providing theoretical answers to the sociological puzzle that plural logics of action produce inconsistent behavioral consequences. PMID:29253867

[The possibility of using PlasmaDeepDive™ MRM panel in clinical diagnostics].

PubMed

Miroshnichenko, Iu V; Petushkova, N A; Moskaleva, N E; Teryaeva, N B; Zgoda, V G; Ilgisonis, E V; Belyaev, A Yu

2015-01-01

Concentrations of 46 proteins have been determined in human blood plasma using PlasmaDeepDive™ MRM Panel ("Biognosys AG", Switzerland). 18 of them were included into the group of proteins with higher concentrations, also identified by the shotgun proteomic analysis. Based on literature data it is concluded that the PlasmaDeepDive™ MRM Panel is applicable for studies of human plasma samples for potential biomarkers of various nervous system disorders.

Tree-level imputation techniques to estimate current plot-level attributes in the Pacific Northwest using paneled inventory data

Treesearch

Bianca Eskelson; Temesgen Hailemariam; Tara Barrett

2009-01-01

The Forest Inventory and Analysis program (FIA) of the US Forest Service conducts a nationwide annual inventory. One panel (20% or 10% of all plots in the eastern and western United States, respectively) is measured each year. The precision of the estimates for any given year from one panel is low, and the moving average (MA), which is considered to be the default...

Composite Sandwich Structures for Shock Mitigation and Energy Absorption

DTIC Science & Technology

2016-06-28

analysis of the blast performance of foam -core, composite sandwich panels was that on a per unit areal weight density basis, lighter and more crushable... foam cores offered greater blast resistance and energy absorption than the heavier and stronger foam cores. This was found to be the case even on an...absolute weight basis for cuNed sandwich panels and panels subjected to underwater blast. 15. SUBJECT TERMS composite; foam -core sandwich; blast

Small Satellite Formations for Distributed Surveillance: System Design and Optimal Control Considerations (Formations de petits satellites pour une surveillance distribuee: Considerations relatives la conception de systeme et a l’optimisation de commandes)

DTIC Science & Technology

2009-04-01

System Analysis and Studies Panel • SCI Systems Concepts and Integration Panel • SET Sensors and Electronics Technology Panel These bodies are... Industriales GRUPO M.TORRES Ctra. Pamplona-Huesca, Km.9 31119 Torres de Elorz (Navarra) Spain +34 948 317 811 +34 948 317 952 irene.eguinoa@mtorres.es

Evaluation of Molecular and Immunohistochemical Adjunct Modalities in the Diagnosis of Soft Tissue Neoplasms.

PubMed

Mourtzoukou, Despoina; Fisher, Cyril; Thway, Khin

2015-12-01

The accurate diagnosis of soft tissue neoplasms has crucial therapeutic and prognostic importance. There is frequent morphologic overlap between entities, and ancillary modalities are used in the vast majority of diagnoses. Immunohistochemistry is rapid and inexpensive, and in addition to the older markers that mainly detected cytoplasmic proteins, antibodies can indirectly detect tumor-specific genetic and molecular abnormalities. The use of molecular diagnostic techniques is now widespread, with molecular services often integrated into routine histopathology laboratories; as their cost and turnaround times begin to parallel those for immunohistochemistry, we compared the usefulness of ancillary immunohistochemistry, molecular genetic, and molecular cytogenetic techniques in the diagnosis of soft tissue lesions. We evaluated the number and contribution of immunohistochemical tests and panels and of ancillary molecular techniques in the primary histopathologic diagnosis of 150 soft tissue lesions. Ninety of 150 cases required either only one immunohistochemical panel or minimal immunohistochemistry for diagnosis, while 39/150 required 2 to 4 panels. In 5/150, ancillary molecular tests alone (without immunohistochemistry) were diagnostically sufficient. The majority of cases required one immunohistochemical panel for diagnosis, with a smaller proportion requiring a second, and a minority requiring a third or fourth (which mainly comprised neoplasms for which the final diagnosis was uncertain). Certain neoplasms required both extensive immunohistochemistry and ancillary molecular testing, despite which the final diagnosis was inconclusive. Ancillary molecular techniques now make a significant contribution to soft tissue tumor diagnosis, being required in over one third (52/150) of cases, and were useful in confirming or excluding tumors that were not possible to conclusively diagnose with histology and immunohistochemistry. Only a small proportion of soft tissue neoplasms (16/150; all benign) did not require immunohistochemistry or ancillary molecular methods, with morphology alone being sufficient for diagnosis. © The Author(s) 2015.

Toxicity assessments of nonsteroidal anti-inflammatory drugs in isolated mitochondria, rat hepatocytes, and zebrafish show good concordance across chemical classes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nadanaciva, Sashi; Aleo, Michael D.; Strock, Christopher J.

To reduce costly late-stage compound attrition, there has been an increased focus on assessing compounds in in vitro assays that predict attributes of human safety liabilities, before preclinical in vivo studies are done. Relevant questions when choosing a panel of assays for predicting toxicity are (a) whether there is general concordance in the data among the assays, and (b) whether, in a retrospective analysis, the rank order of toxicity of compounds in the assays correlates with the known safety profile of the drugs in humans. The aim of our study was to answer these questions using nonsteroidal anti-inflammatory drugs (NSAIDs)more » as a test set since NSAIDs are generally associated with gastrointestinal injury, hepatotoxicity, and/or cardiovascular risk, with mitochondrial impairment and endoplasmic reticulum stress being possible contributing factors. Eleven NSAIDs, flufenamic acid, tolfenamic acid, mefenamic acid, diclofenac, meloxicam, sudoxicam, piroxicam, diflunisal, acetylsalicylic acid, nimesulide, and sulindac (and its two metabolites, sulindac sulfide and sulindac sulfone), were tested for their effects on (a) the respiration of rat liver mitochondria, (b) a panel of mechanistic endpoints in rat hepatocytes, and (c) the viability and organ morphology of zebrafish. We show good concordance for distinguishing among/between NSAID chemical classes in the observations among the three approaches. Furthermore, the assays were complementary and able to correctly identify “toxic” and “non-toxic” drugs in accordance with their human safety profile, with emphasis on hepatic and gastrointestinal safety. We recommend implementing our multi-assay approach in the drug discovery process to reduce compound attrition. - Highlights: • NSAIDS cause liver and GI toxicity. • Mitochondrial uncoupling contributes to NSAID liver toxicity. • ER stress is a mechanism that contributes to liver toxicity. • Zebrafish and cell based assays are complimentary.« less

Family Medicine Panel Size with Care Teams: Impact on Quality.

PubMed

Angstman, Kurt B; Horn, Jennifer L; Bernard, Matthew E; Kresin, Molly M; Klavetter, Eric W; Maxson, Julie; Willis, Floyd B; Grover, Michael L; Bryan, Michael J; Thacher, Tom D

2016-01-01

The demand for comprehensive primary health care continues to expand. The development of team-based practice allows for improved capacity within a collective, collaborative environment. Our hypothesis was to determine the relationship between panel size and access, quality, patient satisfaction, and cost in a large family medicine group practice using a team-based care model. Data were retrospectively collected from 36 family physicians and included total panel size of patients, percentage of time spent on patient care, cost of care, access metrics, diabetic quality metrics, patient satisfaction surveys, and patient care complexity scores. We used linear regression analysis to assess the relationship between adjusted physician panel size, panel complexity, and outcomes. The third available appointments (P < .01) and diabetic quality (P = .03) were negatively affected by increased panel size. Patient satisfaction, cost, and percentage fill rate were not affected by panel size. A physician-adjusted panel size larger than the current mean (2959 patients) was associated with a greater likelihood of poor-quality rankings (≤25th percentile) compared with those with a less than average panel size (odds ratio [OR], 7.61; 95% confidence interval [CI], 1.13-51.46). Increased panel size was associated with a longer time to the third available appointment (OR, 10.9; 95% CI, 1.36-87.26) compared with physicians with panel sizes smaller than the mean. We demonstrated a negative impact of larger panel size on diabetic quality results and available appointment access. Evaluation of a family medicine practice parameters while controlling for panel size and patient complexity may help determine the optimal panel size for a practice. © Copyright 2016 by the American Board of Family Medicine.

A Predictive Model to Estimate Cost Savings of a Novel Diagnostic Blood Panel for Diagnosis of Diarrhea-predominant Irritable Bowel Syndrome.

PubMed

Pimentel, Mark; Purdy, Chris; Magar, Raf; Rezaie, Ali

2016-07-01

A high incidence of irritable bowel syndrome (IBS) is associated with significant medical costs. Diarrhea-predominant IBS (IBS-D) is diagnosed on the basis of clinical presentation and diagnostic test results and procedures that exclude other conditions. This study was conducted to estimate the potential cost savings of a novel IBS diagnostic blood panel that tests for the presence of antibodies to cytolethal distending toxin B and anti-vinculin associated with IBS-D. A cost-minimization (CM) decision tree model was used to compare the costs of a novel IBS diagnostic blood panel pathway versus an exclusionary diagnostic pathway (ie, standard of care). The probability that patients proceed to treatment was modeled as a function of sensitivity, specificity, and likelihood ratios of the individual biomarker tests. One-way sensitivity analyses were performed for key variables, and a break-even analysis was performed for the pretest probability of IBS-D. Budget impact analysis of the CM model was extrapolated to a health plan with 1 million covered lives. The CM model (base-case) predicted $509 cost savings for the novel IBS diagnostic blood panel versus the exclusionary diagnostic pathway because of the avoidance of downstream testing (eg, colonoscopy, computed tomography scans). Sensitivity analysis indicated that an increase in both positive likelihood ratios modestly increased cost savings. Break-even analysis estimated that the pretest probability of disease would be 0.451 to attain cost neutrality. The budget impact analysis predicted a cost savings of $3,634,006 ($0.30 per member per month). The novel IBS diagnostic blood panel may yield significant cost savings by allowing patients to proceed to treatment earlier, thereby avoiding unnecessary testing. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Regression analysis of mixed recurrent-event and panel-count data.

PubMed

Zhu, Liang; Tong, Xinwei; Sun, Jianguo; Chen, Manhua; Srivastava, Deo Kumar; Leisenring, Wendy; Robison, Leslie L

2014-07-01

In event history studies concerning recurrent events, two types of data have been extensively discussed. One is recurrent-event data (Cook and Lawless, 2007. The Analysis of Recurrent Event Data. New York: Springer), and the other is panel-count data (Zhao and others, 2010. Nonparametric inference based on panel-count data. Test 20: , 1-42). In the former case, all study subjects are monitored continuously; thus, complete information is available for the underlying recurrent-event processes of interest. In the latter case, study subjects are monitored periodically; thus, only incomplete information is available for the processes of interest. In reality, however, a third type of data could occur in which some study subjects are monitored continuously, but others are monitored periodically. When this occurs, we have mixed recurrent-event and panel-count data. This paper discusses regression analysis of such mixed data and presents two estimation procedures for the problem. One is a maximum likelihood estimation procedure, and the other is an estimating equation procedure. The asymptotic properties of both resulting estimators of regression parameters are established. Also, the methods are applied to a set of mixed recurrent-event and panel-count data that arose from a Childhood Cancer Survivor Study and motivated this investigation. © The Author 2014. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

The Effect of Economic Growth, Urbanization, and Industrialization on Fine Particulate Matter (PM2.5) Concentrations in China.

PubMed

Li, Guangdong; Fang, Chuanglin; Wang, Shaojian; Sun, Siao

2016-11-01

Rapid economic growth, industrialization, and urbanization in China have led to extremely severe air pollution that causes increasing negative effects on human health, visibility, and climate change. However, the influence mechanisms of these anthropogenic factors on fine particulate matter (PM 2.5 ) concentrations are poorly understood. In this study, we combined panel data and econometric methods to investigate the main anthropogenic factors that contribute to increasing PM 2.5 concentrations in China at the prefecture level from 1999 to 2011. The results showed that PM 2.5 concentrations and three anthropogenic factors were cointegrated. The panel Fully Modified Least Squares and panel Granger causality test results indicated that economic growth, industrialization, and urbanization increased PM 2.5 concentrations in the long run. The results implied that if China persists in its current development pattern, economic growth, industrialization and urbanization will inevitably lead to increased PM 2.5 emissions in the long term. Industrialization was the principal factor that affected PM 2.5 concentrations for the total panel, the industry-oriented panel and the service-oriented panel. PM 2.5 concentrations can be reduced at the cost of short-term economic growth and industrialization. However, reducing the urbanization level is not an efficient way to decrease PM 2.5 pollutions in the short term. The findings also suggest that a rapid reduction of PM 2.5 concentrations relying solely on adjusting these anthropogenic factors is difficult in a short-term for the heavily PM 2.5 -polluted panel. Moreover, the Chinese government will have to seek much broader policies that favor a decoupling of these coupling relationships.

Post-Buckling and Ultimate Strength Analysis of Stiffened Composite Panel Base on Progressive Damage

NASA Astrophysics Data System (ADS)

Zhang, Guofan; Sun, Xiasheng; Sun, Zhonglei

Stiffened composite panel is the typical thin wall structure applied in aerospace industry, and its main failure mode is buckling subjected to compressive loading. In this paper, the development of an analysis approach using Finite Element Method on post-buckling behavior of stiffened composite structures under compression was presented. Then, the numerical results of stiffened panel are obtained by FE simulations. A thorough comparison were accomplished by comparing the load carrying capacity and key position strains of the specimen with test. The comparison indicates that the FEM results which adopted developed methodology could meet the demand of engineering application in predicting the post-buckling behavior of intact stiffened structures in aircraft design stage.

Tensile strength of composite sheets with unidirectional stringers and crack-like damage: A brief report

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.

1984-01-01

The residual strength of composite sheets with bonded composite stringers loaded in tension was determined. The results are summarized. About 50 graphite/epoxy composite panels with crack-like slots were monotonically loaded in tension to failure. Both sheet layup and stringer configuration were varied. The composite panels have considerable damage tolerance. The stringers arrested cracks that ran from the crack-like slots, and the residual strengths were considerably greater than those of unstiffened composite sheets. A stress-intensity factor analysis was developed to predict the failing strains of the stiffened panels. Using the analysis, a single design curve was produced for composite sheets with bonded stringers of any configuration.

Analysis and testing of a soft actuation system for segmented reflector articulation and isolation

NASA Technical Reports Server (NTRS)

Jandura, Louise; Agronin, Michael L.

1991-01-01

Segmented reflectors have been proposed for space-based applications such as optical communication and large-diameter telescopes. An actuation system for mirrors in a space-based segmented mirror array has been developed as part of the National Aeronautics and Space Administration-sponsored Precision Segmented Reflector program. The actuation system, called the Articulated Panel Module (APM), articulates a mirror panel in 3 degrees of freedom in the submicron regime, isolates the panel from structural motion, and simplifies space assembly of the mirrors to the reflector backup truss. A breadboard of the APM has been built and is described. Three-axis modeling, analysis, and testing of the breadboard is discussed.

Iowa's forest resources in 2004

Treesearch

Susan J. Crocker; W. Keith Moser; Gary J. Brand; Aron Flickinger

2006-01-01

Reports analysis of data for five annual panels (2000-2004) of inventory of Iowa's forest resources and one panel (1999 to 2004) of growth, removals, and mortality. Includes information on fores area, number of trees, volume, biomass growth, removals, mortality, and forest health.

Deformation behavior of welded steel sandwich panels under quasi-static loading

DOT National Transportation Integrated Search

2011-03-16

This paper summarizes basic research (i.e., testing and analysis) : conducted to examine the deformation behavior of flat-welded : steel sandwich panels under two types of quasi-static loading: : (1) uniaxial compression; and (2) bending through an i...

Proposed method for determining the thickness of glass in solar collector panels

NASA Technical Reports Server (NTRS)

Moore, D. M.

1980-01-01

An analytical method was developed for determining the minimum thickness for simply supported, rectangular glass plates subjected to uniform normal pressure environmental loads such as wind, earthquake, snow, and deadweight. The method consists of comparing an analytical prediction of the stress in the glass panel to a glass breakage stress determined from fracture mechanics considerations. Based on extensive analysis using the nonlinear finite element structural analysis program ARGUS, design curves for the structural analysis of simply supported rectangular plates were developed. These curves yield the center deflection, center stress and corner stress as a function of a dimensionless parameter describing the load intensity. A method of estimating the glass breakage stress as a function of a specified failure rate, degree of glass temper, design life, load duration time, and panel size is also presented.

Low speed airfoil design and analysis

NASA Technical Reports Server (NTRS)

Eppler, R.; Somers, D. M.

1979-01-01

A low speed airfoil design and analysis program was developed which contains several unique features. In the design mode, the velocity distribution is not specified for one but many different angles of attack. Several iteration options are included which allow the trailing edge angle to be specified while other parameters are iterated. For airfoil analysis, a panel method is available which uses third-order panels having parabolic vorticity distributions. The flow condition is satisfied at the end points of the panels. Both sharp and blunt trailing edges can be analyzed. The integral boundary layer method with its laminar separation bubble analog, empirical transition criterion, and precise turbulent boundary layer equations compares very favorably with other methods, both integral and finite difference. Comparisons with experiment for several airfoils over a very wide Reynolds number range are discussed. Applications to high lift airfoil design are also demonstrated.

A Bayesian Multinomial Probit MODEL FOR THE ANALYSIS OF PANEL CHOICE DATA.

PubMed

Fong, Duncan K H; Kim, Sunghoon; Chen, Zhe; DeSarbo, Wayne S

2016-03-01

A new Bayesian multinomial probit model is proposed for the analysis of panel choice data. Using a parameter expansion technique, we are able to devise a Markov Chain Monte Carlo algorithm to compute our Bayesian estimates efficiently. We also show that the proposed procedure enables the estimation of individual level coefficients for the single-period multinomial probit model even when the available prior information is vague. We apply our new procedure to consumer purchase data and reanalyze a well-known scanner panel dataset that reveals new substantive insights. In addition, we delineate a number of advantageous features of our proposed procedure over several benchmark models. Finally, through a simulation analysis employing a fractional factorial design, we demonstrate that the results from our proposed model are quite robust with respect to differing factors across various conditions.

Substructure analysis using NICE/SPAR and applications of force to linear and nonlinear structures. [spacecraft masts

NASA Technical Reports Server (NTRS)

Razzaq, Zia; Prasad, Venkatesh; Darbhamulla, Siva Prasad; Bhati, Ravinder; Lin, Cai

1987-01-01

Parallel computing studies are presented for a variety of structural analysis problems. Included are the substructure planar analysis of rectangular panels with and without a hole, the static analysis of space mast, using NICE/SPAR and FORCE, and substructure analysis of plane rigid-jointed frames using FORCE. The computations are carried out on the Flex/32 MultiComputer using one to eighteen processors. The NICE/SPAR runstream samples are documented for the panel problem. For the substructure analysis of plane frames, a computer program is developed to demonstrate the effectiveness of a substructuring technique when FORCE is enforced. Ongoing research activities for an elasto-plastic stability analysis problem using FORCE, and stability analysis of the focus problem using NICE/SPAR are briefly summarized. Speedup curves for the panel, the mast, and the frame problems provide a basic understanding of the effectiveness of parallel computing procedures utilized or developed, within the domain of the parameters considered. Although the speedup curves obtained exhibit various levels of computational efficiency, they clearly demonstrate the excellent promise which parallel computing holds for the structural analysis problem. Source code is given for the elasto-plastic stability problem and the FORCE program.

Aeroelastic Analysis Of Versatile Thermal Insulation Panels For Launchers Applications

NASA Astrophysics Data System (ADS)

Carrera, E.; Zappino, E.; Augello, G.; Ferrarese, A.; Montabone, M.

2011-05-01

The aeroelastic behavior of a Versatile Thermal Insulation (VTI) has been investigated. Among the various loadings acting on the panels in this work the attention is payed to fluid structure interaction. e.g. panel flutter phenomena. Known available results from open literature, related to similar problems, permit to analyze the effect of various Mach regimes, including boundary layers thickness effects, in-plane mechanical and thermal loadings, nonlinear effect and amplitude of so called limit cycle oscillations. Dedicated finite element model is developed for the supersonic regime. The model used for coupling orthotropic layered structural model with to Piston Theory aerodynamic models allows the calculations of flutter conditions in case of curved panels supported in a dis- crete number of points. Through this approach the flutter boundaries of the VTI-panel have been investigated.

Thermal Buckling Analysis of Rectangular Panels Subjected to Humped Temperature Profile Heating

NASA Technical Reports Server (NTRS)

Ko, William I.

2004-01-01

This research investigates thermal buckling characteristics of rectangular panels subjected to different types of humped temperature profile heating. Minimum potential energy and finite-element methods are used to calculate the panel buckling temperatures. The two methods give fairly close thermal buckling solutions. 'Buckling temperature magnification factor of the first kind, eta' is established for the fixed panel edges to scale up the buckling solution of uniform temperature loading case to give the buckling solution of the humped temperature profile loading cases. Also, 'buckling temperature magnification factor of the second kind, xi' is established for the free panel edges to scale up the buckling solution of humped temperature profile loading cases with unheated boundary heat sinks to give the buckling solutions when the boundary heat sinks are heated up.

Improving FIA trend analysis through model-based estimation using landsat disturbance maps and the forest vegetation simulator

Treesearch

Sean P. Healey; Gretchen G. Moisen; Paul L. Patterson

2012-01-01

The Forest Inventory and Analysis (FIA) Program's panel system, in which 10-20 percent of the sample is measured in any given year, is designed to increase the currency of FIA reporting and its sensitivity to factors operating at relatively fine temporal scales. Now that much of the country has completed at least one measurement cycle over all panels, there is an...

Stability analysis of nonlinear autonomous systems - General theory and application to flutter

NASA Technical Reports Server (NTRS)

Smith, L. L.; Morino, L.

1975-01-01

The analysis makes use of a singular perturbation method, the multiple time scaling. Concepts of stable and unstable limit cycles are introduced. The solution is obtained in the form of an asymptotic expansion. Numerical results are presented for the nonlinear flutter of panels and airfoils in supersonic flow. The approach used is an extension of a method for analyzing nonlinear panel flutter reported by Morino (1969).

He Who Seeks Shall Find... Or Perhaps Not? Analysis of Firms' Searches for Qualified Personnel, Using Data from the IAB Establishment Panel 2000. IAB Labour Market Research Topics.

ERIC Educational Resources Information Center

Kolling, Arnd

The success of German firms' searches for qualified personnel to fill openings in skilled occupations was examined through a statistical analysis of data from the Institut fur Arbeitsmarkt- und Berufsforschung der Bundesanstalt fur Arbeit's (IAB) establishment panel for 2000. An employer search model was used to explain the current German debate…

Development of the ASTRI heliostat

NASA Astrophysics Data System (ADS)

Coventry, Joe; Arjomandi, Maziar; Barry, John; Blanco, Manuel; Burgess, Greg; Campbell, Jonathan; Connor, Phil; Emes, Matthew; Fairman, Philip; Farrant, David; Ghanadi, Farzin; Grigoriev, Victor; Hall, Colin; Koltun, Paul; Lewis, David; Martin, Scott; Nathan, Graham; Pye, John; Qiu, Ang; Stuart, Wayne; Tang, Youhong; Venn, Felix; Yu, Jeremy

2016-05-01

The Australian Solar Thermal Research Initiative (ASTRI) aims to develop a high optical quality heliostat with target cost - manufactured, installed and operational - of 90 AUD/m2. Three different heliostat design concepts are described, each with features identified during a prior scoping study as having the potential to contribute to cost reduction compared to the current state-of-the-art. The three concepts which are being developed will be down-selected to a single concept for testing in late 2016. The heliostat concept development work is supported by technology development streams, developing novel sandwich panel mirror facet structures, analysing and testing wind loads on heliostats in both stow and operation positions, and developing new heliostat field layouts and software tools for optical analysis of heliostats design concepts.

Behavior of sandwich panels subjected to bending fatigue, axial compression loading and in-plane bending

NASA Astrophysics Data System (ADS)

Mathieson, Haley Aaron

This thesis investigates experimentally and analytically the structural performance of sandwich panels composed of glass fibre reinforced polymer (GFRP) skins and a soft polyurethane foam core, with or without thin GFRP ribs connecting skins. The study includes three main components: (a) out-of-plane bending fatigue, (b) axial compression loading, and (c) in-plane bending of sandwich beams. Fatigue studies included 28 specimens and looked into establishing service life (S-N) curves of sandwich panels without ribs, governed by soft core shear failure and also ribbed panels governed by failure at the rib-skin junction. Additionally, the study compared fatigue life curves of sandwich panels loaded under fully reversed bending conditions (R=-1) with panels cyclically loaded in one direction only (R=0) and established the stiffness degradation characteristics throughout their fatigue life. Mathematical models expressing fatigue life and stiffness degradation curves were calibrated and expanded forms for various loading ratios were developed. Approximate fatigue thresholds of 37% and 23% were determined for non-ribbed panels loaded at R=0 and -1, respectively. Digital imaging techniques showed significant shear contribution significantly (90%) to deflections if no ribs used. Axial loading work included 51 specimens and examined the behavior of panels of various lengths (slenderness ratios), skin thicknesses, and also panels of similar length with various rib configurations. Observed failure modes governing were global buckling, skin wrinkling or skin crushing. In-plane bending involved testing 18 sandwich beams of various shear span-to-depth ratios and skin thicknesses, which failed by skin wrinkling at the compression side. The analytical modeling components of axially loaded panels include; a simple design-oriented analytical failure model and a robust non-linear model capable of predicting the full load-displacement response of axially loaded slender sandwich panels, accounting for P-Delta effects, inherent out-of-straightness profile of any shape at initial conditions, and the excessive shear deformation of soft core and its effect on buckling capacity. Another model was developed to predict the load-deflection response and failure modes of in-plane loaded sandwich beams. After successful verification of the models using experimental results, comprehensive parametric studies were carried out using these models to cover parameters beyond the limitations of the experimental program.

Comparison of various decentralised structural and cavity feedback control strategies for transmitted noise reduction through a double panel structure

NASA Astrophysics Data System (ADS)

Ho, Jen-Hsuan; Berkhoff, Arthur

2014-03-01

This paper compares various decentralised control strategies, including structural and acoustic actuator-sensor configuration designs, to reduce noise transmission through a double panel structure. The comparison is based on identical control stability indexes. The double panel structure consists of two panels with air in between and offers the advantages of low sound transmission at high frequencies, low heat transmission, and low weight. The double panel structure is widely used, such as in the aerospace and automotive industries. Nevertheless, the resonance of the cavity and the poor sound transmission loss at low frequencies limit the double panel's noise control performance. Applying active structural acoustic control to the panels or active noise control to the cavity has been discussed in many papers. In this paper, the resonances of the panels and the cavity are considered simultaneously to further reduce the transmitted noise through an existing double panel structure. A structural-acoustic coupled model is developed to investigate and compare various structural control and cavity control methods. Numerical analysis and real-time control results show that structural control should be applied to both panels. Three types of cavity control sources are presented and compared. The results indicate that the largest noise reduction is obtained with cavity control by loudspeakers modified to operate as incident pressure sources.

Ascertainment bias from imputation methods evaluation in wheat.

PubMed

Brandariz, Sofía P; González Reymúndez, Agustín; Lado, Bettina; Malosetti, Marcos; Garcia, Antonio Augusto Franco; Quincke, Martín; von Zitzewitz, Jarislav; Castro, Marina; Matus, Iván; Del Pozo, Alejandro; Castro, Ariel J; Gutiérrez, Lucía

2016-10-04

Whole-genome genotyping techniques like Genotyping-by-sequencing (GBS) are being used for genetic studies such as Genome-Wide Association (GWAS) and Genomewide Selection (GS), where different strategies for imputation have been developed. Nevertheless, imputation error may lead to poor performance (i.e. smaller power or higher false positive rate) when complete data is not required as it is for GWAS, and each marker is taken at a time. The aim of this study was to compare the performance of GWAS analysis for Quantitative Trait Loci (QTL) of major and minor effect using different imputation methods when no reference panel is available in a wheat GBS panel. In this study, we compared the power and false positive rate of dissecting quantitative traits for imputed and not-imputed marker score matrices in: (1) a complete molecular marker barley panel array, and (2) a GBS wheat panel with missing data. We found that there is an ascertainment bias in imputation method comparisons. Simulating over a complete matrix and creating missing data at random proved that imputation methods have a poorer performance. Furthermore, we found that when QTL were simulated with imputed data, the imputation methods performed better than the not-imputed ones. On the other hand, when QTL were simulated with not-imputed data, the not-imputed method and one of the imputation methods performed better for dissecting quantitative traits. Moreover, larger differences between imputation methods were detected for QTL of major effect than QTL of minor effect. We also compared the different marker score matrices for GWAS analysis in a real wheat phenotype dataset, and we found minimal differences indicating that imputation did not improve the GWAS performance when a reference panel was not available. Poorer performance was found in GWAS analysis when an imputed marker score matrix was used, no reference panel is available, in a wheat GBS panel.

Diagnosis of rheumatoid arthritis: multivariate analysis of biomarkers.

PubMed

Wild, Norbert; Karl, Johann; Grunert, Veit P; Schmitt, Raluca I; Garczarek, Ursula; Krause, Friedemann; Hasler, Fritz; van Riel, Piet L C M; Bayer, Peter M; Thun, Matthias; Mattey, Derek L; Sharif, Mohammed; Zolg, Werner

2008-02-01

To test if a combination of biomarkers can increase the classification power of autoantibodies to cyclic citrullinated peptides (anti-CCP) in the diagnosis of rheumatoid arthritis (RA) depending on the diagnostic situation. Biomarkers were subject to three inclusion/exclusion criteria (discrimination between RA patients and healthy blood donors, ability to identify anti-CCP-negative RA patients, specificity in a panel with major non-rheumatological diseases) before univariate ranking and multivariate analysis was carried out using a modelling panel (n = 906). To enable the evaluation of the classification power in different diagnostic settings the disease controls (n = 542) were weighted according to the admission rates in rheumatology clinics modelling a clinic panel or according to the relative prevalences of musculoskeletal disorders in the general population seen by general practitioners modelling a GP panel. Out of 131 biomarkers considered originally, we evaluated 32 biomarkers in this study, of which only seven passed the three inclusion/exclusion criteria and were combined by multivariate analysis using four different mathematical models. In the modelled clinic panel, anti-CCP was the lead marker with a sensitivity of 75.8% and a specificity of 94.0%. Due to the lack in specificity of the markers other than anti-CCP in this diagnostic setting, any gain in sensitivity by any marker combination is off-set by a corresponding loss in specificity. In the modelled GP panel, the best marker combination of anti-CCP and interleukin (IL)-6 resulted in a sensitivity gain of 7.6% (85.9% vs. 78.3%) at a minor loss in specificity of 1.6% (90.3% vs. 91.9%) compared with anti-CCP as the best single marker. Depending on the composition of the sample panel, anti-CCP alone or anti-CCP in combination with IL-6 has the highest classification power for the diagnosis of established RA.

Evaluation of a Composite Sandwich Fuselage Side Panel with Damage and Subjected to Internal Pressure

NASA Technical Reports Server (NTRS)

Rouse, Marshall; Ambur, Damodar R.; Bodine, Jerry; Dopker, Bernhard

1997-01-01

The results from an experimental and analytical study of a composite sandwich fuselage side panel for a transport aircraft are presented. The panel has two window cutouts and three frames, and has been evaluated with internal pressure loads that generate biaxial tension loading conditions. Design limit load and design ultimate load tests have been performed on the graphite-epoxy sandwich panel with the middle frame removed to demonstrate the suitability of this two-frame design for supporting the prescribed biaxial loading conditions with twice the initial frame spacing of 20 inches. The two-frame panel was damaged by cutting a notch that originates at the edge of a cutout and extends in the panel hoop direction through the window-belt area. This panel with a notch was tested in a combined-load condition to demonstrate the structural damage tolerance at the design limit load condition. The two panel configurations successfully satisfied all design load requirements in the experimental part of the study, and the three-frame and two-frame panel responses are fully explained by the analysis results. The results of this study suggest that there is potential for using sandwich structural concepts with greater than the usual 20-in.-wide frame spacing to further reduce aircraft fuselage structural weight.

Retort beef aroma that gives preferable properties to canned beef products and its aroma components.

PubMed

Migita, Koshiro; Iiduka, Takao; Tsukamoto, Kie; Sugiura, Sayuri; Tanaka, Genichiro; Sakamaki, Gousuke; Yamamoto, Yasufumi; Takeshige, Yusuke; Miyazawa, Toshio; Kojima, Ayako; Nakatake, Tomoko; Okitani, Akihiro; Matsuishi, Masanori

2017-12-01

The objective of this study is to identify the properties and responsible compounds for the aromatic roast odor (retort beef aroma) that commonly occurs in canned beef products and could contribute to their palatability. The optimal temperature for generating retort beef aroma was 121°C. An untrained panel evaluated both uncured corned beef and canned yamato-ni beef and found that they had an aroma that was significantly (P < 0.01) similar to the odor of 121°C-heated beef than 100°C-heated beef. The panel also noted that the aroma of 121°C-heated beef tended to be (P < 0.1) preferable than that of 100°C-heated beef. These results suggest that retort beef aroma is one constituent of palatability in canned beef. GC-MS (gas chromatography-mass spectrometry) analysis of the volatile fraction obtained from 100°C- and 121°C-heated beef showed that the amounts of pyrazine, 2-methylpyrazine and diacetyl were higher in the 121°C-heated beef than in the 100°C-heated beef. GC-sniffing revealed that the odor quality of pyrazines was similar to that of retort beef aroma. Therefore, pyrazines were suggested to be a candidate responsible for the retort beef aroma. Analysis of commercial uncured corned beef and cured corned beef confirmed the presence of pyrazine, 2-methylpyrazine and 2,6-dimethylpyrazine. © 2017 Japanese Society of Animal Science.

Host Genetic and Environmental Effects on Mouse Cecum Microbiota

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campbell, James H; Foster, Carmen M; Vishnivetskaya, Tatiana A

2012-01-01

The mammalian gut harbors complex and variable microbial communities, across both host phylogenetic space and conspecific individuals. A synergy of host genetic and environmental factors shape these communities and account for their variability, but their individual contributions and the selective pressures involved are still not well understood. We employed barcoded pyrosequencing of V1-2 and V4 regions of bacterial small subunit ribosomal RNA genes to characterize the effects of host genetics and environment on cecum assemblages in 10 genetically distinct, inbred mouse strains. Eight of these strains are the foundation of the Collaborative Cross (CC), a panel of mice derived frommore » a genetically diverse set of inbred founder strains, designed specifically for complex trait analysis. Diversity of gut microbiota was characterized by complementing phylogenetic and distance-based, sequence-clustering approaches. Significant correlations were found between the mouse strains and their gut microbiota, reflected by distinct bacterial communities. Cohabitation and litter had a reduced, although detectable effect, and the microbiota response to these factors varied by strain. We identified bacterial phylotypes that appear to be discriminative and strain-specific to each mouse line used. Cohabitation of different strains of mice revealed an interaction of host genetic and environmental factors in shaping gut bacterial consortia, in which bacterial communities became more similar but retained strain specificity. This study provides a baseline analysis of intestinal bacterial communities in the eight CC progenitor strains and will be linked to integrated host genotype, phenotype and microbiota research on the resulting CC panel.« less

Non-circulatory fluid forces on porous bodies with application to panel flutter

NASA Astrophysics Data System (ADS)

Hajian, Rozhin; Jaworski, Justin W.

2017-11-01

The non-circulatory fluid forces acting on an oscillating porous panel or airfoil in uniform incompressible flow are derived from linearized potential theory. The fundamental integral equation for Holder-continuous porosity distributions is formulated and solved numerically for the special cases of non-porous and uniformly-porous panels with prescribed structural deformations. The new unsteady aerodynamic forces are then applied to aeroelastic stability predictions for porous panels or liners. Results from this analysis aim to form the basis of a complete unsteady aerodynamic theory for porous airfoils and their acoustic emissions based upon the unique attributes of natural fliers and swimmers.

On an integro-differential equation model for the study of the response of an acoustically coupled panel

NASA Technical Reports Server (NTRS)

Yen, D. H. Y.; Maestrello, L.; Padula, S.

1975-01-01

The response of a clamped panel to supersonically convected turbulence is considered. A theoretical model in the form of an integro-differential equation is employed that takes into account the coupling between the panel motion and the surrounding acoustic medium. The kernels of the integrals, which represent induced pressures due to the panel motion, are Green's functions for sound radiations under various moving and stationary sources. An approximate analysis is made by following a finite-element Ritz-Galerkin procedure. Preliminary numerical results, in agreement with experimental findings, indicate that the acoustic damping is the controlling mechanism of the response.

Free vibration of functionally graded carbon nanotube reinforced composite cylindrical panels with general elastic supports

NASA Astrophysics Data System (ADS)

Xie, Fei; Tang, Jinyuan; Wang, Ailun; Shuai, Cijun; Wang, Qingshan

2018-05-01

In this paper, a unified solution for vibration analysis of the functionally graded carbon nanotube reinforced composite (FG-CNTRC) cylindrical panels with general elastic supports is carried out via using the Ritz method. The excellent accuracy and reliability of the present method are compared with the results of the classical boundary cases found in the literature. New results are given for vibration characteristics of FG-CNTRC cylindrical panels with various boundary conditions. The effects of the elastic restraint parameters, thickness, subtended angle and volume fraction of carbon nanotubes on the free vibration characteristic of the cylindrical panels are also reported.

Climate change and biometeorology, the International Society of Biometeorology and its journal: a perspective on the past and a framework for the future.

PubMed

Beggs, Paul John

2014-01-01

Anthropogenic climate change is inherently a biometeorological issue. As such, it would be reasonably expected that the International Society of Biometeorology (ISB) and its journal, International Journal of Biometeorology (IJB), would have had climate change feature prominently in their activities, articles etc., and to therefore have made a substantial and valuable contribution to the science of the issue. This article presents an analysis of climate change science in ISB and IJB. The analysis focusses on climate-change-related publications by ISB Presidents found through searches of Thomson Reuters Web of Science; contributions to the Intergovernmental Panel on Climate Change's (IPCC's) Working Group II (WGII) by ISB Presidents; and climate change-related publications in IJB found through searches of Thomson Reuters Web of Science. The results demonstrate that the ISB, as represented by its recent, current, and future Presidents, is actively engaged in climate change research and the production of scholarly climate change publications. For example, ISB Presidents have contributed as authors to all four IPCC WGII Assessment Reports, with some Presidents having contributed to more than one Assessment Report or several chapters of the one report. Similarly, it is evident that the IJB is increasingly attracting and publishing climate-change-related articles, with such articles generally having greater impact (as indicated by citations) than other IJB articles. Opportunities for the ISB to provide an internal framework for, and showcase, its climate change work are described. Such opportunities, if enacted, would complement the recent creation of two IJB climate change Field Editor positions.

Climate change and biometeorology, the International Society of Biometeorology and its journal: a perspective on the past and a framework for the future

NASA Astrophysics Data System (ADS)

Beggs, Paul John

2014-01-01

Anthropogenic climate change is inherently a biometeorological issue. As such, it would be reasonably expected that the International Society of Biometeorology (ISB) and its journal, International Journal of Biometeorology ( IJB), would have had climate change feature prominently in their activities, articles etc., and to therefore have made a substantial and valuable contribution to the science of the issue. This article presents an analysis of climate change science in ISB and IJB. The analysis focusses on climate-change-related publications by ISB Presidents found through searches of Thomson Reuters Web of Science; contributions to the Intergovernmental Panel on Climate Change's (IPCC's) Working Group II (WGII) by ISB Presidents; and climate change-related publications in IJB found through searches of Thomson Reuters Web of Science. The results demonstrate that the ISB, as represented by its recent, current, and future Presidents, is actively engaged in climate change research and the production of scholarly climate change publications. For example, ISB Presidents have contributed as authors to all four IPCC WGII Assessment Reports, with some Presidents having contributed to more than one Assessment Report or several chapters of the one report. Similarly, it is evident that the IJB is increasingly attracting and publishing climate-change-related articles, with such articles generally having greater impact (as indicated by citations) than other IJB articles. Opportunities for the ISB to provide an internal framework for, and showcase, its climate change work are described. Such opportunities, if enacted, would complement the recent creation of two IJB climate change Field Editor positions.

The potential European genetic predisposition for non-contact anterior cruciate ligament injury.

PubMed

Astur, Diego Costa; Andrade, Edilson; Arliani, Gustavo Gonçalves; Debieux, Pedro; Loyola, Leonor Casilla; Dos Santos, Sidney Emanuel Batista; Burbano, Rommel Mario Rodriguez; Leal, Mariana Ferreira; Cohen, Moises

2018-05-04

Previous research has provided evidence of a hereditary predisposition for anterior cruciate ligament (ACL) injury. The purpose of this study was to evaluate the association between ancestral population genetics and risk of non-contact ACL injuries. Blood samples were collected from 177 individuals with a history of non-contact ACL injury and 556 non-injured control individuals for analysis of the genetic material through the use of a panel of 48 INDELs ancestry genetic markers from three ancestral origins. Among patients with non-contact ACL injury, 82% were male and 18% were female. In the control group, 78% were male, and 22% were female. The mean age of the non-contact ACL injury group was 31.7 years (± 10.2), and the control group was 33.8 years (± 13.2). The individual genetic contribution from INDELs of each ancestral origin varied considerably: ranging between 1.5-94.8% contribution for INDELs of African origin (mean of 21.4% of INDELs); between 2 and 96.1% contribution for INDELs of European origin (mean of 66.7% of INDELs); and between 1.3-96.4% contribution for INDELs of Amerindian origin (mean of 11.7% of INDELs). When comparing paired subjects from the non-contact ACL and control groups, the genetic analysis showed that the European ancestry score was higher in the non-contact ACL group than control group (0.70 ± 0.21 vs 0.63 ± 0.22 respectively, p < 0.001), whereas African ancestry scores (ACL group 0.18 ± 0.18 vs control group 0.24 ± 0.21, p < 0.001) and Amerindian ancestry scores (ACL group 0.11 ± 0.09 vs control group 0.12 ± 0.10, n.s.) were lower among the non-contact ACL group than in controls. European INDELs markers were found to represent a potential genetic predisposition for non-contact ACL injuries when compared to African and Amerindian INDELs. This study has the potential to correlate a measurable and distinct genetic marker with risk of a non-contact ACL injury. Thus, it increases knowledge base and volume of molecular and genetical factors associated with this pathology. Furthermore, this study provides guidance and evidence for the development of genetic risk-screening panels for non-contact ACL injury. Level III Diagnostic Study.

Combined Loads Test Fixture for Thermal-Structural Testing Aerospace Vehicle Panel Concepts

NASA Technical Reports Server (NTRS)

Fields, Roger A.; Richards, W. Lance; DeAngelis, Michael V.

2004-01-01

A structural test requirement of the National Aero-Space Plane (NASP) program has resulted in the design, fabrication, and implementation of a combined loads test fixture. Principal requirements for the fixture are testing a 4- by 4-ft hat-stiffened panel with combined axial (either tension or compression) and shear load at temperatures ranging from room temperature to 915 F, keeping the test panel stresses caused by the mechanical loads uniform, and thermal stresses caused by non-uniform panel temperatures minimized. The panel represents the side fuselage skin of an experimental aerospace vehicle, and was produced for the NASP program. A comprehensive mechanical loads test program using the new test fixture has been conducted on this panel from room temperature to 500 F. Measured data have been compared with finite-element analyses predictions, verifying that uniform load distributions were achieved by the fixture. The overall correlation of test data with analysis is excellent. The panel stress distributions and temperature distributions are very uniform and fulfill program requirements. This report provides details of an analytical and experimental validation of the combined loads test fixture. Because of its simple design, this unique test fixture can accommodate panels from a variety of aerospace vehicle designs.

A pilot Internet "value of health" panel: recruitment, participation and compliance.

PubMed

Stein, Ken; Dyer, Matthew; Crabb, Tania; Milne, Ruairidh; Round, Alison; Ratcliffe, Julie; Brazier, John

2006-11-27

To pilot using a panel of members of the public to provide preference data via the Internet A stratified random sample of members of the general public was recruited and familiarized with the standard gamble procedure using an Internet based tool. Health states were periodically presented in "sets" corresponding to different conditions, during the study. The following were described: Recruitment (proportion of people approached who were trained); Participation (a) the proportion of people trained who provided any preferences and (b) the proportion of panel members who contributed to each "set" of values; and Compliance (the proportion, per participant, of preference tasks which were completed). The influence of covariates on these outcomes was investigated using univariate and multivariate analyses. A panel of 112 people was recruited. 23% of those approached (n = 5,320) responded to the invitation, and 24% of respondents (n = 1,215) were willing to participate (net = 5.5%). However, eventual recruitment rates, following training, were low (2.1% of those approached). Recruitment from areas of high socioeconomic deprivation and among ethnic minority communities was low. Eighteen sets of health state descriptions were considered over 14 months. 74% of panel members carried out at least one valuation task. People from areas of higher socioeconomic deprivation and unmarried people were less likely to participate. An average of 41% of panel members expressed preferences on each set of descriptions. Compliance ranged from 3% to 100%. It is feasible to establish a panel of members of the general public to express preferences on a wide range of health state descriptions using the Internet, although differential recruitment and attrition are important challenges. Particular attention to recruitment and retention in areas of high socioeconomic deprivation and among ethnic minority communities is necessary. Nevertheless, the panel approach to preference measurement using the Internet offers the potential to provide specific utility data in a responsive manner for use in economic evaluations and to address some of the outstanding methodological uncertainties in this field.

A retrospective analysis of the effect of discussion in teleconference and face-to-face scientific peer-review panels

PubMed Central

Carpenter, Afton S; Sullivan, Joanne H; Deshmukh, Arati; Glisson, Scott R; Gallo, Stephen A

2015-01-01

Objective With the use of teleconferencing for grant peer-review panels increasing, further studies are necessary to determine the efficacy of the teleconference setting compared to the traditional onsite/face-to-face setting. The objective of this analysis was to examine the effects of discussion, namely changes in application scoring premeeting and postdiscussion, in these settings. We also investigated other parameters, including the magnitude of score shifts and application discussion time in face-to-face and teleconference review settings. Design The investigation involved a retrospective, quantitative analysis of premeeting and postdiscussion scores and discussion times for teleconference and face-to-face review panels. The analysis included 260 and 212 application score data points and 212 and 171 discussion time data points for the face-to-face and teleconference settings, respectively. Results The effect of discussion was found to be small, on average, in both settings. However, discussion was found to be important for at least 10% of applications, regardless of setting, with these applications moving over a potential funding line in either direction (fundable to unfundable or vice versa). Small differences were uncovered relating to the effect of discussion between settings, including a decrease in the magnitude of the effect in the teleconference panels as compared to face-to-face. Discussion time (despite teleconferences having shorter discussions) was observed to have little influence on the magnitude of the effect of discussion. Additionally, panel discussion was found to often result in a poorer score (as opposed to an improvement) when compared to reviewer premeeting scores. This was true regardless of setting or assigned reviewer type (primary or secondary reviewer). Conclusions Subtle differences were observed between settings, potentially due to reduced engagement in teleconferences. Overall, further research is required on the psychology of decision-making, team performance and persuasion to better elucidate the group dynamics of telephonic and virtual ad-hoc peer-review panels. PMID:26351194

A blueprint for computational analysis of acoustical scattering from orchestral panel arrays

NASA Astrophysics Data System (ADS)

Burns, Thomas

2005-09-01

Orchestral panel arrays have been a topic of interest to acousticians, and it is reasonable to expect optimal design criteria to result from a combination of musician surveys, on-stage empirical data, and computational modeling of various configurations. Preparing a musicians survey to identify specific mechanisms of perception and sound quality is best suited for a clinically experienced hearing scientist. Measuring acoustical scattering from a panel array and discerning the effects from various boundaries is best suited for the experienced researcher in engineering acoustics. Analyzing a numerical model of the panel arrays is best suited for the tools typically used in computational engineering analysis. Toward this end, a streamlined process will be described using PROENGINEER to define a panel array geometry in 3-D, a commercial mesher to numerically discretize this geometry, SYSNOISE to solve the associated boundary element integral equations, and MATLAB to visualize the results. The model was run (background priority) on an SGI Altix (Linux) server with 12 CPUs, 24 Gbytes of RAM, and 1 Tbyte of disk space. These computational resources are available to research teams interested in this topic and willing to write and pursue grants.

Panel Flutter Emulation Using a Few Concentrated Forces

NASA Astrophysics Data System (ADS)

Dhital, Kailash; Han, Jae-Hung

2018-04-01

The objective of this paper is to study the feasibility of panel flutter emulation using a few concentrated forces. The concentrated forces are considered to be equivalent to aerodynamic forces. The equivalence is carried out using surface spline method and principle of virtual work. The structural modeling of the plate is based on the classical plate theory and the aerodynamic modeling is based on the piston theory. The present approach differs from the linear panel flutter analysis in scheming the modal aerodynamics forces with unchanged structural properties. The solutions for the flutter problem are obtained numerically using the standard eigenvalue procedure. A few concentrated forces were considered with an optimization effort to decide their optimal locations. The optimization process is based on minimizing the error between the flutter bounds from emulated and linear flutter analysis method. The emulated flutter results for the square plate of four different boundary conditions using six concentrated forces are obtained with minimal error to the reference value. The results demonstrated the workability and viability of using concentrated forces in emulating real panel flutter. In addition, the paper includes the parametric studies of linear panel flutter whose proper literatures are not available.

Macroeconomic effects on mortality revealed by panel analysis with nonlinear trends.

PubMed

Ionides, Edward L; Wang, Zhen; Tapia Granados, José A

2013-10-03

Many investigations have used panel methods to study the relationships between fluctuations in economic activity and mortality. A broad consensus has emerged on the overall procyclical nature of mortality: perhaps counter-intuitively, mortality typically rises above its trend during expansions. This consensus has been tarnished by inconsistent reports on the specific age groups and mortality causes involved. We show that these inconsistencies result, in part, from the trend specifications used in previous panel models. Standard econometric panel analysis involves fitting regression models using ordinary least squares, employing standard errors which are robust to temporal autocorrelation. The model specifications include a fixed effect, and possibly a linear trend, for each time series in the panel. We propose alternative methodology based on nonlinear detrending. Applying our methodology on data for the 50 US states from 1980 to 2006, we obtain more precise and consistent results than previous studies. We find procyclical mortality in all age groups. We find clear procyclical mortality due to respiratory disease and traffic injuries. Predominantly procyclical cardiovascular disease mortality and countercyclical suicide are subject to substantial state-to-state variation. Neither cancer nor homicide have significant macroeconomic association.

Macroeconomic effects on mortality revealed by panel analysis with nonlinear trends

PubMed Central

Ionides, Edward L.; Wang, Zhen; Tapia Granados, José A.

2013-01-01

Many investigations have used panel methods to study the relationships between fluctuations in economic activity and mortality. A broad consensus has emerged on the overall procyclical nature of mortality: perhaps counter-intuitively, mortality typically rises above its trend during expansions. This consensus has been tarnished by inconsistent reports on the specific age groups and mortality causes involved. We show that these inconsistencies result, in part, from the trend specifications used in previous panel models. Standard econometric panel analysis involves fitting regression models using ordinary least squares, employing standard errors which are robust to temporal autocorrelation. The model specifications include a fixed effect, and possibly a linear trend, for each time series in the panel. We propose alternative methodology based on nonlinear detrending. Applying our methodology on data for the 50 US states from 1980 to 2006, we obtain more precise and consistent results than previous studies. We find procyclical mortality in all age groups. We find clear procyclical mortality due to respiratory disease and traffic injuries. Predominantly procyclical cardiovascular disease mortality and countercyclical suicide are subject to substantial state-to-state variation. Neither cancer nor homicide have significant macroeconomic association. PMID:24587843

Report of the panel on lithospheric structure and evolution, section 3

NASA Technical Reports Server (NTRS)

Chase, Clement G.; Lang, Harold; Mcnutt, Marcia K.; Paylor, Earnest D.; Sandwell, David T.; Stern, Robert J.

1991-01-01

The panel concluded that NASA can contribute to developing a refined understanding of the compositional, structural, and thermal differences between continental and oceanic lithosphere through a vigorous program in solid Earth science with the following objectives: determine the most fundamental geophysical property of the planet; determine the global gravity field to an accuracy of a few milliGals at wavelengths of 100 km or less; determine the global lithospheric magnetic field to a few nanoTeslas at a wavelength of 100 km; determine how the lithosphere has evolved to its present state via acquiring geologic remote sensing data over all the continents.

Sensory analysis of characterising flavours: evaluating tobacco product odours using an expert panel.

PubMed

Krüsemann, Erna J Z; Lasschuijt, Marlou P; de Graaf, C; de Wijk, René A; Punter, Pieter H; van Tiel, Loes; Cremers, Johannes W J M; van de Nobelen, Suzanne; Boesveldt, Sanne; Talhout, Reinskje

2018-05-23

Tobacco flavours are an important regulatory concept in several jurisdictions, for example in the USA, Canada and Europe. The European Tobacco Products Directive 2014/40/EU prohibits cigarettes and roll-your-own tobacco having a characterising flavour. This directive defines characterising flavour as 'a clearly noticeable smell or taste other than one of tobacco […]'. To distinguish between products with and without a characterising flavour, we trained an expert panel to identify characterising flavours by smelling. An expert panel (n=18) evaluated the smell of 20 tobacco products using self-defined odour attributes, following Quantitative Descriptive Analysis. The panel was trained during 14 attribute training, consensus training and performance monitoring sessions. Products were assessed during six test sessions. Principal component analysis, hierarchical clustering (four and six clusters) and Hotelling's T-tests (95% and 99% CIs) were used to determine differences and similarities between tobacco products based on odour attributes. The final attribute list contained 13 odour descriptors. Panel performance was sufficient after 14 training sessions. Products marketed as unflavoured that formed a cluster were considered reference products. A four-cluster method distinguished cherry-flavoured, vanilla-flavoured and menthol-flavoured products from reference products. Six clusters subdivided reference products into tobacco leaves, roll-your-own and commercial products. An expert panel was successfully trained to assess characterising odours in cigarettes and roll-your-own tobacco. This method could be applied to other product types such as e-cigarettes. Regulatory decisions on the choice of reference products and significance level are needed which directly influences the products being assessed as having a characterising odour. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Recommendations of the Panel on Cost-effectiveness in Health and Medicine.

PubMed

Weinstein, M C; Siegel, J E; Gold, M R; Kamlet, M S; Russell, L B

1996-10-16

To develop consensus-based recommendations for the conduct of cost-effectiveness analysis (CEA). This article, the second in a 3-part series, describes the basis for recommendations constituting the reference case analysis, the set of practices developed to guide CEAs that inform societal resource allocation decisions, and the content of these recommendations. The Panel on Cost-Effectiveness in Health and Medicine, a nonfederal panel with expertise in CEA, clinical medicine, ethics, and health outcomes measurement, was convened by the US Public Health Service (PHS). The panel reviewed the theoretical foundations of CEA, current practices, and alternative methods used in analyses. Recommendations were developed on the basis of theory where possible, but tempered by ethical and pragmatic considerations, as well as the needs of users. The panel developed recommendations through 2 1/2 years of discussions. Comments on preliminary drafts prepared by panel working groups were solicited from federal government methodologists, health agency officials, and academic methodologists. The panel's methodological recommendations address (1) components belonging in the numerator and denominator of a cost-effectiveness (C/E) ratio; (2) measuring resource use in the numerator of a C/E ratio; (3) valuing health consequences in the denominator of a C/E ratio; (4) estimating effectiveness of interventions; (5) incorporating time preference and discounting; and (6) handling uncertainty. Recommendations are subject to the ¿rule of reason,¿ balancing the burden engendered by a practice with its importance to a study. If researchers follow a standard set of methods in CEA, the quality and comparability of studies, and their ultimate utility, can be much improved.

Unlocking Potential in Gerontology.

ERIC Educational Resources Information Center

Hartmann, Joyce; And Others

Papers and materials contributed by four panelists are provided from a panel presentation. "Unlocking Potential in Gerontology" (Theodore W. Wischropp) explains the make-up and organization of two consortia involved in the aging projects in Kansas, briefly describes three federally funded grants, and addresses some issues from the…

NASA Hispanic Heritage Month Event, ¡Latinos STEM Up!

NASA Image and Video Library

2017-10-12

On Oct. 12, NASA’s Hispanic Outreach and Leadership Alliance (HOLA) celebrated Hispanic Heritage month with a panel discussion of the contributions of Hispanics to NASA’s mission and the importance of Hispanic representation in science, technology, engineering and mathematics (STEM) education and careers.

Proposal of a trigger tool to assess adverse events in dental care.

PubMed

Corrêa, Claudia Dolores Trierweiler Sampaio de Oliveira; Mendes, Walter

2017-11-21

The aim of this study was to propose a trigger tool for research of adverse events in outpatient dentistry in Brazil. The tool was elaborated in two stages: (i) to build a preliminary set of triggers, a literature review was conducted to identify the composition of trigger tools used in other areas of health and the principal adverse events found in dentistry; (ii) to validate the preliminarily constructed triggers a panel of experts was organized using the modified Delphi method. Fourteen triggers were elaborated in a tool with explicit criteria to identify potential adverse events in dental care, essential for retrospective patient chart reviews. Studies on patient safety in dental care are still incipient when compared to other areas of health care. This study intended to contribute to the research in this field. The contribution by the literature and guidance from the expert panel allowed elaborating a set of triggers to detect adverse events in dental care, but additional studies are needed to test the instrument's validity.

Dynamics of social health insurance development: examining the determinants of Chinese basic health insurance coverage with panel data.

PubMed

Liu, Jun-Qiang

2011-08-01

Social health insurance (SHI) is gaining popularity in many developing countries, but there are few systematic empirical studies on the dynamics of SHI development. This study investigates the determinants of coverage of the Basic Healthcare Insurance for Urban Employees (BHI) in China. Using a panel database ranging from 1999 to 2007, the study finds that: (1) economic development plays a valuable role in BHI development; (2) strong financial capacity and administrative capacity in the government contributes to BHI progress; (3) higher trade union density is closely related to more rapid BHI expansion; and (4) taxation agencies are better at collecting SHI premiums. These findings provide evidence-based lessons for new and ongoing SHI programs. In addition, this article aims to make a more general contribution to the study of social policy development by expanding the scope of current theories on social policy development. Copyright © 2011 Elsevier Ltd. All rights reserved.

Lung cancer signature biomarkers: tissue specific semantic similarity based clustering of digital differential display (DDD) data.

PubMed

Srivastava, Mousami; Khurana, Pankaj; Sugadev, Ragumani

2012-11-02

The tissue-specific Unigene Sets derived from more than one million expressed sequence tags (ESTs) in the NCBI, GenBank database offers a platform for identifying significantly and differentially expressed tissue-specific genes by in-silico methods. Digital differential display (DDD) rapidly creates transcription profiles based on EST comparisons and numerically calculates, as a fraction of the pool of ESTs, the relative sequence abundance of known and novel genes. However, the process of identifying the most likely tissue for a specific disease in which to search for candidate genes from the pool of differentially expressed genes remains difficult. Therefore, we have used 'Gene Ontology semantic similarity score' to measure the GO similarity between gene products of lung tissue-specific candidate genes from control (normal) and disease (cancer) sets. This semantic similarity score matrix based on hierarchical clustering represents in the form of a dendrogram. The dendrogram cluster stability was assessed by multiple bootstrapping. Multiple bootstrapping also computes a p-value for each cluster and corrects the bias of the bootstrap probability. Subsequent hierarchical clustering by the multiple bootstrapping method (α = 0.95) identified seven clusters. The comparative, as well as subtractive, approach revealed a set of 38 biomarkers comprising four distinct lung cancer signature biomarker clusters (panel 1-4). Further gene enrichment analysis of the four panels revealed that each panel represents a set of lung cancer linked metastasis diagnostic biomarkers (panel 1), chemotherapy/drug resistance biomarkers (panel 2), hypoxia regulated biomarkers (panel 3) and lung extra cellular matrix biomarkers (panel 4). Expression analysis reveals that hypoxia induced lung cancer related biomarkers (panel 3), HIF and its modulating proteins (TGM2, CSNK1A1, CTNNA1, NAMPT/Visfatin, TNFRSF1A, ETS1, SRC-1, FN1, APLP2, DMBT1/SAG, AIB1 and AZIN1) are significantly down regulated. All down regulated genes in this panel were highly up regulated in most other types of cancers. These panels of proteins may represent signature biomarkers for lung cancer and will aid in lung cancer diagnosis and disease monitoring as well as in the prediction of responses to therapeutics.

Self-transcendence and depression among AIDS Memorial Quilt panel makers.

PubMed

Kausch, Kurt D; Amer, Kim

2007-06-01

Self-transcendence is a process that can help individuals reestablish well-being after experiencing a significant, life-altering event. In this study, we sought to identify the relationship between self-transcendence and depression in individuals who lost loved ones to HIV/AIDS and to describe and compare self-transcendence, self-transcendence variables of acceptance and spirituality, and depression among bereaved individuals who created AIDS Memorial Quilt panels with those who did not. The findings support Reed's self-transcendence theory, with inverse correlations between self-transcendence and depression obtained from both the total group and the panel makers. Significant differences were also found between certain self-transcendence variables and depression among the study participants related to gender and ethnicity. In addition, thematic analysis of panel maker interviews revealed five themes: Quilt panel making provides validation, Quilt panel making creates a living memory, liberating acceptance of loss, community of survivors, and connection to a higher power. These findings assist in understanding the complexities of the grief process and support the usefulness of Quilt panel making as an intervention for coping with grief related to HIV/AIDS.

Optimization of composite sandwich cover panels subjected to compressive loadings

NASA Technical Reports Server (NTRS)

Cruz, Juan R.

1991-01-01

An analysis and design method is presented for the design of composite sandwich cover panels that include the transverse shear effects and damage tolerance considerations. This method is incorporated into a sandwich optimization computer program entitled SANDOP. As a demonstration of its capabilities, SANDOP is used in the present study to design optimized composite sandwich cover panels for for transport aircraft wing applications. The results of this design study indicate that optimized composite sandwich cover panels have approximately the same structural efficiency as stiffened composite cover panels designed to satisfy individual constraints. The results also indicate that inplane stiffness requirements have a large effect on the weight of these composite sandwich cover panels at higher load levels. Increasing the maximum allowable strain and the upper percentage limit of the 0 degree and +/- 45 degree plies can yield significant weight savings. The results show that the structural efficiency of these optimized composite sandwich cover panels is relatively insensitive to changes in core density. Thus, core density should be chosen by criteria other than minimum weight (e.g., damage tolerance, ease of manufacture, etc.).

Packaging, deployment, and panel design concepts for a truss-stiffened 7-panel precision deployable reflector with feed boom

NASA Technical Reports Server (NTRS)

Heard, Walter L., Jr.; Collins, Timothy J.; Dyess, James W.; Kenner, Scott; Bush, Harold G.

1993-01-01

A concept is presented for achieving a remotely deployable truss-stiffened reflector consisting of seven integrated sandwich panels that form the reflective surface, and an integrated feed boom. The concept has potential for meeting aperture size and surface precision requirements for some high-frequency microwave remote sensing applications. The packaged reflector/feed boom configuration is a self-contained unit that can be conveniently attached to a spacecraft bus. The package has a cylindrical envelope compatible with typical launch vehicle shrouds. Dynamic behavior of a deployed configuration having a 216-inch focal length and consisting of 80-inch-diameter, two-inch-thick panels is examined through finite-element analysis. Results show that the feed boom and spacecraft bus can have a large impact on the fundamental frequency of the deployed configuration. Two candidate rib-stiffened sandwich panel configurations for this application are described, and analytical results for panel mass and stiffness are presented. Results show that the addition of only a few rib stiffeners, if sufficiently deep, can efficiently improve sandwich panel stiffness.

Design construction and analysis of solar ridge concentrator photovoltaic (PV) system to improve battery charging performance.

PubMed

Narasimman, Kalaiselvan; Selvarasan, Iniyan

2016-05-01

A ridge concentrator photovoltaic system for a 10W multi-crystalline solar panel was designed with the concentration ratios of 1X and 2X. The ray tracing model of ridge concentrator photovoltaic system was carried out using Trace-Pro simulation. The optimum tilt angle for the concentrator PV system throughout the year was computed. The electrical parameters of the 3 panels were analyzed. The effect of temperature on the electrical performance of the panel was also studied. The reduction of voltage due to increasing panel temperature was managed by MPES type Charge controller. Glass reflector with reflectivity 0.95 was chosen as the ridge wall for the concentrator system. The maximum power outputs for the 1X and 2X panel reached were 9W and 10.5W with glass reflector. The percentage of power improvement for 1X and 2X concentrations were 22.3% and 45.8% respectively. The 2X concentrated panel connected battery takes lower time to charge compared with normal panel connected battery. Copyright © 2016. Published by Elsevier Inc.

Carbon Balance and Contribution of Harvested Wood Products in China Based on the Production Approach of the Intergovernmental Panel on Climate Change.

PubMed

Ji, Chunyi; Cao, Wenbin; Chen, Yong; Yang, Hongqiang

2016-11-12

The carbon sequestration of harvested wood products (HWP) plays an important role in climate mitigation. Accounting the carbon contribution of national HWP carbon pools has been listed as one of the key topics for negotiation in the United Nations Framework Convention on Climate Change. On the basis of the revised Production Approach of the Intergovernmental Panel on Climate Change (2013) (IPCC), this study assessed the accounting of carbon stock and emissions from the HWP pool in China and then analyzed its balance and contribution to carbon mitigation from 1960 to 2014. Research results showed that the accumulated carbon stock in China's HWP carbon pool increased from 130 Teragrams Carbon (TgC) in 1960 to 705.6 TgC in 2014. The annual increment in the carbon stock rose from 3.2 TgC in 1960 to 45.2 TgC in 2014. The category of solid wood products accounted for approximately 95% of the annual amount. The reduction in carbon emissions was approximately twelve times that of the emissions from the HWP producing and processing stage during the last decade. Furthermore, the amount of carbon stock and emission reduction increased from 23 TgC in 1960 to 76.1 TgC in 2014. The annual contribution of HWP could compensate for approximately 2.9% of the national carbon dioxide emissions in China.

Carbon Balance and Contribution of Harvested Wood Products in China Based on the Production Approach of the Intergovernmental Panel on Climate Change

PubMed Central

Ji, Chunyi; Cao, Wenbin; Chen, Yong; Yang, Hongqiang

2016-01-01

The carbon sequestration of harvested wood products (HWP) plays an important role in climate mitigation. Accounting the carbon contribution of national HWP carbon pools has been listed as one of the key topics for negotiation in the United Nations Framework Convention on Climate Change. On the basis of the revised Production Approach of the Intergovernmental Panel on Climate Change (2013) (IPCC), this study assessed the accounting of carbon stock and emissions from the HWP pool in China and then analyzed its balance and contribution to carbon mitigation from 1960 to 2014. Research results showed that the accumulated carbon stock in China’s HWP carbon pool increased from 130 Teragrams Carbon (TgC) in 1960 to 705.6 TgC in 2014. The annual increment in the carbon stock rose from 3.2 TgC in 1960 to 45.2 TgC in 2014. The category of solid wood products accounted for approximately 95% of the annual amount. The reduction in carbon emissions was approximately twelve times that of the emissions from the HWP producing and processing stage during the last decade. Furthermore, the amount of carbon stock and emission reduction increased from 23 TgC in 1960 to 76.1 TgC in 2014. The annual contribution of HWP could compensate for approximately 2.9% of the national carbon dioxide emissions in China. PMID:27845760

An investigation into NVC characteristics of vehicle behaviour using modal analysis

NASA Astrophysics Data System (ADS)

Hanouf, Zahir; Faris, Waleed F.; Ahmad, Kartini

2017-03-01

NVC characterizations of vehicle behavior is one essential part of the development targets in automotive industries. Therefore understanding dynamic behavior of each structural part of the vehicle is a major requirement in improving the NVC characteristics of a vehicle. The main focus of this research is to investigate structural dynamic behavior of a passenger car using modal analysis part by part technique and apply this method to derive the interior noise sources. In the first part of this work computational modal analysis part by part tests were carried out to identify the dynamic parameters of the passenger car. Finite elements models of the different parts of the car are constructed using VPG 3.2 software. Ls-Dyna pre and post processing was used to identify and analyze the dynamic behavior of each car components panels. These tests had successfully produced natural frequencies and their associated mode shapes of such panels like trunk, hood, roof and door panels. In the second part of this research, experimental modal analysis part by part is performed on the selected car panels to extract modal parameters namely frequencies and mode shapes. The study establishes the step-by-step procedures to carry out experimental modal analysis on the car structures, using single input excitation and multi-output responses (SIMO) technique. To ensure the validity of the results obtained by the previous method an inverse method was done by fixing the response and moving the excitation and the results found were absolutely the same. Finally, comparison between results obtained from both analyses showed good similarity in both frequencies and mode shapes. Conclusion drawn from this part of study was that modal analysis part-by-part can be strongly used to establish the dynamic characteristics of the whole car. Furthermore, the developed method is also can be used to show the relationship between structural vibration of the car panels and the passengers’ noise comfort inside the cabin.

Minimizing preventable trauma deaths in a limited-resource setting: a test-case of a multidisciplinary panel review approach at the Komfo Anokye Teaching Hospital in Ghana.

PubMed

Yeboah, Dominic; Mock, Charles; Karikari, Patrick; Agyei-Baffour, Peter; Donkor, Peter; Ebel, Beth

2014-07-01

Our objectives were to determine the proportion of preventable trauma deaths at a large trauma hospital in Kumasi, Ghana, and to identify opportunities for the improvement of trauma care. A multidisciplinary panel of experts evaluated pre-hospital, hospital, and postmortem data of consecutive trauma patients who died over a 5-month period in 2006-2007 at the Komfo Anokye Teaching Hospital. The panel judged the preventability of each death. For preventable and potentially preventable deaths, deficiencies in care that contributed to their deaths were identified. The panel reviewed 231 trauma deaths. Of these, 84 charts had sufficient information to review preventable factors. The panel determined that 23 % of trauma deaths were definitely preventable, 37 % were potentially preventable, and 40 % were not preventable. One main deficiency in care was identified for each of the 50 definitely preventable and potentially preventable deaths. The most common deficiencies were pre-hospital delays (44 % of the 50 deficiencies), delay in treatment (32 %), and inadequate fluid resuscitation (22 %). Among the 19 definitely preventable deaths, the most common cause of death was hemorrhage (47 %), and the most common deficiencies were inadequate fluid resuscitation (37 % of deficiencies in this group) and pre-hospital delay (37 %). A high proportion of trauma fatalities might have been preventable by decreasing pre-hospital delays, adequate resuscitation in hospital, and earlier initiation of care, including definitive surgical management. The study also showed that preventable death panel reviews are a feasible and useful quality improvement method in the study setting.

An investigation on the determinants of carbon emissions for OECD countries: empirical evidence from panel models robust to heterogeneity and cross-sectional dependence.

PubMed

Dogan, Eyup; Seker, Fahri

2016-07-01

This empirical study analyzes the impacts of real income, energy consumption, financial development and trade openness on CO2 emissions for the OECD countries in the Environmental Kuznets Curve (EKC) model by using panel econometric approaches that consider issues of heterogeneity and cross-sectional dependence. Results from the Pesaran CD test, the Pesaran-Yamagata's homogeneity test, the CADF and the CIPS unit root tests, the LM bootstrap cointegration test, the DSUR estimator, and the Emirmahmutoglu-Kose Granger causality test indicate that (i) the panel time-series data are heterogeneous and cross-sectionally dependent; (ii) CO2 emissions, real income, the quadratic income, energy consumption, financial development and openness are integrated of order one; (iii) the analyzed data are cointegrated; (iv) the EKC hypothesis is validated for the OECD countries; (v) increases in openness and financial development mitigate the level of emissions whereas energy consumption contributes to carbon emissions; (vi) a variety of Granger causal relationship is detected among the analyzed variables; and (vii) empirical results and policy recommendations are accurate and efficient since panel econometric models used in this study account for heterogeneity and cross-sectional dependence in their estimation procedures.

A multi-criteria decision analysis assessment of waste paper management options.

PubMed

Hanan, Deirdre; Burnley, Stephen; Cooke, David

2013-03-01

The use of Multi-criteria Decision Analysis (MCDA) was investigated in an exercise using a panel of local residents and stakeholders to assess the options for managing waste paper on the Isle of Wight. Seven recycling, recovery and disposal options were considered by the panel who evaluated each option against seven environmental, financial and social criteria. The panel preferred options where the waste was managed on the island with gasification and recycling achieving the highest scores. Exporting the waste to the English mainland for incineration or landfill proved to be the least preferred options. This research has demonstrated that MCDA is an effective way of involving community groups in waste management decision making. Copyright © 2012 Elsevier Ltd. All rights reserved.

NASA Langley developments in response calculations needed for failure and life prediction

NASA Technical Reports Server (NTRS)

Housner, Jerrold M.

1993-01-01

NASA Langley developments in response calculations needed for failure and life predictions are discussed. Topics covered include: structural failure analysis in concurrent engineering; accuracy of independent regional modeling demonstrated on classical example; functional interface method accurately joins incompatible finite element models; interface method for insertion of local detail modeling extended to curve pressurized fuselage window panel; interface concept for joining structural regions; motivation for coupled 2D-3D analysis; compression panel with discontinuous stiffener coupled 2D-3D model and axial surface strains at the middle of the hat stiffener; use of adaptive refinement with multiple methods; adaptive mesh refinement; and studies on quantity effect of bow-type initial imperfections on reliability of stiffened panels.

Subcomponent tests for composite fuselage technology readiness

NASA Technical Reports Server (NTRS)

Madan, R. C.; Hawley, A. V.

1989-01-01

An account is given of a NASA research effort aimed at the development of an all-composite transport aircraft fuselage incorporating joints and cutouts which meets all design requirements. The design, construction, and analysis activities associated with the 30-ft-long fuselage section gave attention to critically important subcomponent specimens, including shear-tee pulloff specimens, stiffened and unstiffened cutout panels, longitudinal and transverse skin splices, longeron runouts, transverse skin-longerons, stiffened shear panels, and window belt panels. The analysis of large cutouts was conducted with coupling FEM analyses incorporating accurate failure criteria for tension and shear; the strategic application of S2 glass fiber plies around cutouts was demonstrated both analytically and experimentally to increase load capacity with virtually no weight penalty.

Design and analysis of a stiffened composite fuselage panel

NASA Technical Reports Server (NTRS)

Dickson, J. N.; Biggers, S. B.

1980-01-01

The design and analysis of stiffened composite panel that is representative of the fuselage structure of existing wide bodied aircraft is discussed. The panel is a minimum weight design, based on the current level of technology and realistic loads and criteria. Several different stiffener configurations were investigated in the optimization process. The final configuration is an all graphite/epoxy J-stiffened design in which the skin between adjacent stiffeners is permitted to buckle under design loads. Fail safe concepts typically employed in metallic fuselage structure have been incorporated in the design. A conservative approach has been used with regard to structural details such as skin/frame and stringer/frame attachments and other areas where sufficient design data was not available.

COMMAND: A FORTRAN program for simplified composite analysis and design. [computerized design of multilayered composite panels

NASA Technical Reports Server (NTRS)

Vanderplaats, G. N.

1976-01-01

A FORTRAN program is presented for preliminary analysis and design of multilayered composite panels subjected to inplane loads. All plys are of the same material. The composite is assumed symmetric about the midplane, but need not be balanced. Failure criterion includes limit ply strains and lower bounds on composite inplane stiffnesses. Multiple load conditions are considered. The required input data is defined and examples are provided to aid the use in making the program operational. Average panel design times are two seconds on an IBM 360/67 computer. Results are compared with published literature. A complete FORTRAN listing of program COMAND is provided. In addition, the optimization program CONMIN is required for design.

A general panel method for the analysis and design of arbitrary configurations in incompressible flows. [boundary value problem

NASA Technical Reports Server (NTRS)

Johnson, F. T.

1980-01-01

A method for solving the linear integral equations of incompressible potential flow in three dimensions is presented. Both analysis (Neumann) and design (Dirichlet) boundary conditions are treated in a unified approach to the general flow problem. The method is an influence coefficient scheme which employs source and doublet panels as boundary surfaces. Curved panels possessing singularity strengths, which vary as polynomials are used, and all influence coefficients are derived in closed form. These and other features combine to produce an efficient scheme which is not only versatile but eminently suited to the practical realities of a user-oriented environment. A wide variety of numerical results demonstrating the method is presented.

A SWOT analysis of the organization and financing of the Danish health care system.

PubMed

Christiansen, Terkel

2002-02-01

The organization and financing of the Danish health care system was evaluated within a framework of a SWOT analysis (analysis of Strengths, Weaknesses, Opportunities and Threats) by a panel of five members with a background in health economics. The present paper describes the methods and materials used for the evaluation: selection of panel members, structure of the evaluation task according to the health care triangle model, selection of background material consisting of documents and literature on the Danish health care system, and a 1-week study visit.

Analysis of Discrete-Source Damage Progression in a Tensile Stiffened Composite Panel

NASA Technical Reports Server (NTRS)

Wang, John T.; Lotts, Christine G.; Sleight, David W.

1999-01-01

This paper demonstrates the progressive failure analysis capability in NASA Langley s COMET-AR finite element analysis code on a large-scale built-up composite structure. A large-scale five stringer composite panel with a 7-in. long discrete source damage was analyzed from initial loading to final failure including the geometric and material nonlinearities. Predictions using different mesh sizes, different saw cut modeling approaches, and different failure criteria were performed and assessed. All failure predictions have a reasonably good correlation with the test result.

A Comprehensive Structural Analysis Process for Failure Assessment in Aircraft Lap-Joint Mimics Using Multi-Modal Fusion of NDE Data (Preprint)

DTIC Science & Technology

2012-07-01

plates with dimensions of 254 mm (10") by 76.2 mm (3") with a nominal thickness of 1.6 mm (0.063’’). Two aluminum plates were stacked and riveted to...create a lap-joint mimic test panel. Thus, ten aluminum plates produced five test panels. Prior to stacking and riveting , the aluminum plates of the... riveted region of the panels. 5 Approved for public release; distribution unlimited. Figure 1

Factors Influencing the Accuracy of Aerodynamic Hinge-Moment Prediction

DTIC Science & Technology

1978-08-01

condition on the aft lifting surfaces and flaps. A new modeling technique for trailing-edge wake analysis using a potential- flow program based on the...control surface as depicLed in figure 21.. Three different models are used to simulate the flow on the wing, the flap, and the gaps. In the first two panel...ized sense, similar to that implemented in the FLEXSTAB program. The modeling of the wake on the side-edge gaps differs in the first two panel models

Solar maximum mission panel jettison analysis remote manipulator system

NASA Technical Reports Server (NTRS)

Bauer, R. B.

1980-01-01

A study is presented of the development of the Remote Manipulator System (RMS) configurations for jettison of the solar panels on the Solar Maximum Mission/Multimission Satellite. A valid RMS maneuver between jettison configurations was developed. Arm and longeron loads and effector excursions due to the solar panel jettison were determined to see if they were within acceptable limits. These loads and end effector excursions were analyzed under two RMS modes, servos active in position hold submode, and in the brakes on mode.

Model Analysis of an Aircraft Fueslage Panel using Experimental and Finite-Element Techniques

NASA Technical Reports Server (NTRS)

Fleming, Gary A.; Buehrle, Ralph D.; Storaasli, Olaf L.

1998-01-01

The application of Electro-Optic Holography (EOH) for measuring the center bay vibration modes of an aircraft fuselage panel under forced excitation is presented. The requirement of free-free panel boundary conditions made the acquisition of quantitative EOH data challenging since large scale rigid body motions corrupted measurements of the high frequency vibrations of interest. Image processing routines designed to minimize effects of large scale motions were applied to successfully resurrect quantitative EOH vibrational amplitude measurements

Thermal conductivity of Rene 41 honeycomb panels

NASA Astrophysics Data System (ADS)

Deriugin, V.

1980-12-01

Effective thermal conductivities of Rene 41 panels suitable for advanced space transportation vehicle structures were determined analytically and experimentally for temperature ranges between 20.4K (423 F) and 1186K (1675 F). The cryogenic data were obtained using a cryostat whereas the high temperature data were measured using a heat flow meter and a comparative thermal conductivity instrument respectively. Comparisons were made between analysis and experimental data. Analytical methods appear to provide reasonable definition of the honeycomb panel effective thermal conductivities.

Thermal conductivity of Rene 41 honeycomb panels. [space transportation vehicles

NASA Technical Reports Server (NTRS)

Deriugin, V.

1980-01-01

Effective thermal conductivities of Rene 41 panels suitable for advanced space transportation vehicle structures were determined analytically and experimentally for temperature ranges between 20.4K (423 F) and 1186K (1675 F). The cryogenic data were obtained using a cryostat whereas the high temperature data were measured using a heat flow meter and a comparative thermal conductivity instrument respectively. Comparisons were made between analysis and experimental data. Analytical methods appear to provide reasonable definition of the honeycomb panel effective thermal conductivities.

An innovative and shared methodology for event reconstruction using images in forensic science.

PubMed

Milliet, Quentin; Jendly, Manon; Delémont, Olivier

2015-09-01

This study presents an innovative methodology for forensic science image analysis for event reconstruction. The methodology is based on experiences from real cases. It provides real added value to technical guidelines such as standard operating procedures (SOPs) and enriches the community of practices at stake in this field. This bottom-up solution outlines the many facets of analysis and the complexity of the decision-making process. Additionally, the methodology provides a backbone for articulating more detailed and technical procedures and SOPs. It emerged from a grounded theory approach; data from individual and collective interviews with eight Swiss and nine European forensic image analysis experts were collected and interpreted in a continuous, circular and reflexive manner. Throughout the process of conducting interviews and panel discussions, similarities and discrepancies were discussed in detail to provide a comprehensive picture of practices and points of view and to ultimately formalise shared know-how. Our contribution sheds light on the complexity of the choices, actions and interactions along the path of data collection and analysis, enhancing both the researchers' and participants' reflexivity. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Compression Buckling Behavior of Large-Scale Friction Stir Welded and Riveted 2090-T83 Al-Li Alloy Skin-Stiffener Panels

NASA Technical Reports Server (NTRS)

Hoffman, Eric K.; Hafley, Robert A.; Wagner, John A.; Jegley, Dawn C.; Pecquet, Robert W.; Blum, Celia M.; Arbegast, William J.

2002-01-01

To evaluate the potential of friction stir welding (FSW) as a replacement for traditional rivet fastening for launch vehicle dry bay construction, a large-scale friction stir welded 2090-T83 aluminum-lithium (Al-Li) alloy skin-stiffener panel was designed and fabricated by Lockheed-Martin Space Systems Company - Michoud Operations (LMSS) as part of NASA Space Act Agreement (SAA) 446. The friction stir welded panel and a conventional riveted panel were tested to failure in compression at the NASA Langley Research Center (LaRC). The present paper describes the compression test results, stress analysis, and associated failure behavior of these panels. The test results provide useful data to support future optimization of FSW processes and structural design configurations for launch vehicle dry bay structures.

Study of low-velocity impact response of sandwich panels with shear-thickening gel cores

NASA Astrophysics Data System (ADS)

Wang, Yunpeng; Gong, Xinglong; Xuan, Shouhu

2018-06-01

The low-velocity impact response of sandwich panels with shear-thickening gel cores was studied. The impact tests indicated that the sandwich panels with shear-thickening gel cores showed excellent properties of energy dissipation and stress distribution. In comparison to the similar sandwich panels with chloroprene rubber cores and ethylene-propylene-diene monomer cores, the shear-thickening gel cores led to the obviously smaller contact forces and the larger energy absorptions. Numerical modelling with finite element analysis was used to investigate the stress distribution of the sandwich panels with shear-thickening gel cores and the results agreed well with the experimental results. Because of the unique mechanical property of the shear-thickening gel, the concentrated stress on the front facesheets were distributed to larger areas on the back facesheets and the peak stresses were reduced greatly.

Buckling Behavior of Compression-Loaded Quasi-Isotropic Curved Panels with a Circular Cutout

NASA Technical Reports Server (NTRS)

Hilburger, Mark W.; Britt, Vicki O.; Nemeth, Michael P.

1999-01-01

Results from a numerical and experimental study of the response of compression-loaded quasi-isotropic curved panels with a centrally located circular cutout are presented. The numerical results were obtained by using a geometrically nonlinear finite element analysis code. The effects of cutout size, panel curvature and initial geo- metric imperfections on the overall response of compression-loaded panels are described. In addition, results are presented from a numerical parametric study that indicate the effects of elastic circumferential edge restraints on the prebuckling and buckling response of a selected panel and these numerical results are compared to experimentally measured results. These restraints are used to identify the effects of circumferential edge restraints that are introduced by the test fixture that was used in the present study. It is shown that circumferential edge restraints can introduce substantial nonlinear prebuckling deformations into shallow compression-loaded curved panels that can results in a significant increase in buckling load.

Analysis of Palm Oil Production, Export, and Government Consumption to Gross Domestic Product of Five Districts in West Kalimantan by Panel Regression

NASA Astrophysics Data System (ADS)

Sulistianingsih, E.; Kiftiah, M.; Rosadi, D.; Wahyuni, H.

2017-04-01

Gross Domestic Product (GDP) is an indicator of economic growth in a region. GDP is a panel data, which consists of cross-section and time series data. Meanwhile, panel regression is a tool which can be utilised to analyse panel data. There are three models in panel regression, namely Common Effect Model (CEM), Fixed Effect Model (FEM) and Random Effect Model (REM). The models will be chosen based on results of Chow Test, Hausman Test and Lagrange Multiplier Test. This research analyses palm oil about production, export, and government consumption to five district GDP are in West Kalimantan, namely Sanggau, Sintang, Sambas, Ketapang and Bengkayang by panel regression. Based on the results of analyses, it concluded that REM, which adjusted-determination-coefficient is 0,823, is the best model in this case. Also, according to the result, only Export and Government Consumption that influence GDP of the districts.

Test and Analysis of Sub-Components of Aluminum-Lithium Alloy Cylinders

NASA Technical Reports Server (NTRS)

Haynie, Waddy T.; Chunchu, Prasad B.; Satyanarayana, Arunkumar; Hilburger, Mark W.; Smith, Russell W.

2012-01-01

Integrally machined blade-stiffened panels subjected to an axial compressive load were tested and analyzed to observe the buckling, crippling, and postcrippling response of the panels. The panels were fabricated from aluminum-lithium alloys 2195 and 2050, and both alloys have reduced material properties in the short transverse material direction. The tests were designed to capture a failure mode characterized by the stiffener separating from the panel in the postbuckling range. This failure mode is attributed to the reduced properties in the short transverse direction. Full-field measurements of displacements and strains using three-dimensional digital image correlation systems and local measurements using strain gages were used to capture the deformation of the panel leading up to the failure of the panel for specimens fabricated from 2195. High-speed cameras were used to capture the initiation of the failure. Finite element models were developed using an isotropic strain-hardening material model. Good agreement was observed between the measured and predicted responses for both alloys.

Mechanical and thermal buckling analysis of sandwich panels under different edge conditions

NASA Technical Reports Server (NTRS)

Ko, William L.

1993-01-01

By using the Rayleigh-Ritz method of minimizing the total potential energy of a structural system, combined load (mechanical or thermal load) buckling equations are established for orthotropic rectangular sandwich panels supported under four different edge conditions. Two-dimensional buckling interaction curves and three dimensional buckling interaction surfaces are constructed for high-temperature honeycomb-core sandwich panels supported under four different edge conditions. The interaction surfaces provide easy comparison of the panel buckling strengths and the domains of symmetrical and antisymmetrical buckling associated with the different edge conditions. Thermal buckling curves of the sandwich panels also are presented. The thermal buckling conditions for the cases with and without thermal moments were found to be identical for the small deformation theory. In sandwich panels, the effect of transverse shear is quite large, and by neglecting the transverse shear effect, the buckling loads could be overpredicted considerably. Clamping of the edges could greatly increase buckling strength more in compression than in shear.

Content validation using an expert panel: assessment process for assistive technology adopted by farmers with disabilities.

PubMed

Mathew, S N; Field, W E; French, B F

2011-07-01

This article reports the use of an expert panel to perform content validation of an experimental assessment process for the safety of assistive technology (AT) adopted by farmers with disabilities. The validation process was conducted by a panel of six experts experienced in the subject matter, i.e., design, use, and assessment of AT for farmers with disabilities. The exercise included an evaluation session and two focus group sessions. The evaluation session consisted of using the assessment process under consideration by the panel to evaluate a set of nine ATs fabricated by a farmer on his farm site. The expert panel also participated in the focus group sessions conducted immediately before and after the evaluation session. The resulting data were analyzed using discursive analysis, and the results were incorporated into the final assessment process. The method and the results are presented with recommendations for the use of expert panels in research projects and validation of assessment tools.

Comparison of quantitative flow cytometric data provided by panels with lower and increased color number

NASA Astrophysics Data System (ADS)

Bocsi, József; Mittag, Anja; Pierzchalski, Arkadiusz; Baumgartner, Adolf; Dähnert, Ingo; Tárnok, Attila

2012-03-01

To date the flow cytometry (FCM) industry is booming with new generations of commercial clinical instruments. Long-term clinical studies have the dilemma that moving to new instruments being capable of more complex cell-analysis makes it difficult to compare new data with those obtained on older instruments with less complex analysis panels. Since 15 years we conduct follow-up studies on children with congenital heart diseases. In this period we moved from 2- to 3- and now to 10-color FCM immunophenotyping panels. Questions arise how to compare and transfer data from lower to higher level of complexity. Two comparable antibody panels for leukocyte immunophenotyping (12-tube 2-colors, and 9-tube 4-colors) were measured on a BD FACScalibur FCM (calibration: Spherotech beads) in 19 blood samples from children with congenital heart disease. This increase of colors was accompanied by moving antibodies that were in the 2-color panel either FITC or PE labeled to red dyes such as PerCP or APC. Algorithms were developed for bridging data for quantitative characterization of antigen expression (mean fluorescence intensity) and frequency of different cell subpopulations in combination with rainbow bead standard data. This approach worked for the most relevant antibodies (CD3, CD4, CD8 etc.) well, but rendered substantial uncertainty for activation markers (CD69 etc.). Our techniques are particularly well suited to the analysis in long-term studies and have the potential to compare older and recent results in a standardized way.

Weight optimal design of lateral wing upper covers made of composite materials

NASA Astrophysics Data System (ADS)

Barkanov, Evgeny; Eglītis, Edgars; Almeida, Filipe; Bowering, Mark C.; Watson, Glenn

2016-09-01

The present investigation is devoted to the development of a new optimal design of lateral wing upper covers made of advanced composite materials, with special emphasis on closer conformity of the developed finite element analysis and operational requirements for aircraft wing panels. In the first stage, 24 weight optimization problems based on linear buckling analysis were solved for the laminated composite panels with three types of stiffener, two stiffener pitches and four load levels, taking into account manufacturing, reparability and damage tolerance requirements. In the second stage, a composite panel with the best weight/design performance from the previous study was verified by nonlinear buckling analysis and optimization to investigate the effect of shear and fuel pressure on the performance of stiffened panels, and their behaviour under skin post-buckling. Three rib-bay laminated composite panels with T-, I- and HAT-stiffeners were modelled with ANSYS, NASTRAN and ABAQUS finite element codes to study their buckling behaviour as a function of skin and stiffener lay-ups, stiffener height, stiffener top and root width. Owing to the large dimension of numerical problems to be solved, an optimization methodology was developed employing the method of experimental design and response surface technique. Optimal results obtained in terms of cross-sectional areas were verified successfully using ANSYS and ABAQUS shared-node models and a NASTRAN rigid-linked model, and were used later to estimate the weight of the Advanced Low Cost Aircraft Structures (ALCAS) lateral wing upper cover.

NREL Leadership Contributes to Revision of Key Energy Integration Standard,

Science.gov Websites

interconnection standard for distributed energy resource technologies, including rooftop solar panels. The , which establishes uniform requirements for interconnection of distributed energy resources (DERs), such foundation for integrating clean renewable energy technologies as well as other distributed generation and

Multiple Indicator Stationary Time Series Models.

ERIC Educational Resources Information Center

Sivo, Stephen A.

2001-01-01

Discusses the propriety and practical advantages of specifying multivariate time series models in the context of structural equation modeling for time series and longitudinal panel data. For time series data, the multiple indicator model specification improves on classical time series analysis. For panel data, the multiple indicator model…

NCATE's Blue Ribbon Panel Report and NAPDS: Working Together

ERIC Educational Resources Information Center

Van Scoy, Irma J.

2012-01-01

An expert panel including representatives from schools/districts, teacher education, and professional education associations was convened by the National Council for the Accreditation of Teacher Education (NCATE) to make recommendations regarding clinical preparation in teacher education. This article presents an analysis of how the ten design…

75 FR 55625 - Occupational Information Development Advisory Panel Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-13

... claims; occupational analysis, including definitions, ratings and capture of physical and mental... should contact the Panel staff by any one of these three methods: Mail: Occupational Information... Federal Officer. [FR Doc. 2010-22711 Filed 9-10-10; 8:45 am] BILLING CODE 4191-02-P ...

75 FR 71787 - Occupational Information Development Advisory Panel Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-24

... recommendations will relate to our disability programs in the following areas: medical and vocational analysis of... medical-vocational adjudication policies and processes. Agenda: The Panel will meet on Wednesday, December... business. Those interested in providing testimony in person at the meeting or via teleconference should...

Experimental Study of the Bending Properties and Deformation Analysis of Web-Reinforced Composite Sandwich Floor Slabs with Four Simply Supported Edges.

PubMed

Qi, Yujun; Fang, Hai; Liu, Weiqing

2016-01-01

Web-reinforced composite sandwich panels exhibit good mechanical properties in one-way bending, but few studies have investigated their flexural behavior and deformation calculation methods under conditions of four simply supported edges. This paper studies the bending performance of and deformation calculation methods for two-way web-reinforced composite sandwich panels with different web spacing and heights. Polyurethane foam, two-way orthogonal glass-fiber woven cloth and unsaturated resin were used as raw materials in this study. Vacuum infusion molding was used to prepare an ordinary composite sandwich panel and 5 web-reinforced composite sandwich panels with different spacing and web heights. The panels were subjected to two-way panel bending tests with simple support for all four edges. The mechanical properties of these sandwich panels during the elastic stage were determined by applying uniformly distributed loads. The non-linear mechanical characteristics and failure modes were obtained under centrally concentrated loading. Finally, simulations of the sandwich panels, which used the mechanical model established herein, were used to deduce the formulae for the deflection deformation for this type of sandwich panel. The experimental results show that webs can significantly improve the limit bearing capacity and flexural rigidity of sandwich panels, with smaller web spacing producing a stronger effect. When the web spacing is 75 mm, the limit bearing capacity is 4.63 times that of an ordinary sandwich panel. The deduced deflection calculation formulae provide values that agree well with the measurements (maximum error <15%). The results that are obtained herein can provide a foundation for the structural design of this type of panel.

Experimental Study of the Bending Properties and Deformation Analysis of Web-Reinforced Composite Sandwich Floor Slabs with Four Simply Supported Edges

PubMed Central

Qi, Yujun; Fang, Hai; Liu, Weiqing

2016-01-01

Web-reinforced composite sandwich panels exhibit good mechanical properties in one-way bending, but few studies have investigated their flexural behavior and deformation calculation methods under conditions of four simply supported edges. This paper studies the bending performance of and deformation calculation methods for two-way web-reinforced composite sandwich panels with different web spacing and heights. Polyurethane foam, two-way orthogonal glass-fiber woven cloth and unsaturated resin were used as raw materials in this study. Vacuum infusion molding was used to prepare an ordinary composite sandwich panel and 5 web-reinforced composite sandwich panels with different spacing and web heights. The panels were subjected to two-way panel bending tests with simple support for all four edges. The mechanical properties of these sandwich panels during the elastic stage were determined by applying uniformly distributed loads. The non-linear mechanical characteristics and failure modes were obtained under centrally concentrated loading. Finally, simulations of the sandwich panels, which used the mechanical model established herein, were used to deduce the formulae for the deflection deformation for this type of sandwich panel. The experimental results show that webs can significantly improve the limit bearing capacity and flexural rigidity of sandwich panels, with smaller web spacing producing a stronger effect. When the web spacing is 75 mm, the limit bearing capacity is 4.63 times that of an ordinary sandwich panel. The deduced deflection calculation formulae provide values that agree well with the measurements (maximum error <15%). The results that are obtained herein can provide a foundation for the structural design of this type of panel. PMID:26871435

Identification of a novel CHEK2 variant and assessment of its contribution to the risk of breast cancer in French Canadian women.

PubMed

Novak, David J; Chen, Long Qi; Ghadirian, Parviz; Hamel, Nancy; Zhang, Phil; Rossiny, Vanessa; Cardinal, Guy; Robidoux, André; Tonin, Patricia N; Rousseau, Francois; Narod, Steven A; Foulkes, William D

2008-08-15

BRCA1 and BRCA2 account for the majority of the known familial breast cancer risk, however, the impact of other cancer susceptibility genes largely remains to be elucidated. Checkpoint Kinase 2 (CHEK2) is an important signal transducer of cellular responses to DNA damage, whose defects have been associated with an increase in breast cancer risk. Previous studies have identified low penetrance CHEK2 alleles such as 1100delC and I157T, as well as variants such as S428F in the Ashkenazi Jewish population and IVS2 + 1G>A in the Polish population. No founder allele has been specifically identified in the French Canadian population. The 14 coding exons of CHEK2 were fully sequenced for variant alleles in a panel of 25 affected French Canadian women and 25 healthy controls. Two variants were identified of which one novel variant was further screened for in an additional panel of 667 breast cancer patients and 6548 healthy controls. Additional genotyping was conducted using allele specific PCR and a restriction digest assay. Significance of amino acid substitutions were deduced by employing comparative analysis techniques. Two variants were identified: the previously reported silent substitution 252A>G (E84E) and the novel missense variant, 1217G>A (R406H). No significant difference in allele distribution between French Canadian women with breast cancer and healthy controls was observed (3/692, 0.43% vs. 22/6573, 0.33%, respectively, P = 0.73). The novel CHEK2 missense variant identified in this study, R406H, is unlikely to contribute to breast cancer risk in French Canadian women.

Identification of a novel CHEK2 variant and assessment of its contribution to the risk of breast cancer in French Canadian women

PubMed Central

Novak, David J; Chen, Long Qi; Ghadirian, Parviz; Hamel, Nancy; Zhang, Phil; Rossiny, Vanessa; Cardinal, Guy; Robidoux, André; Tonin, Patricia N; Rousseau, Francois; Narod, Steven A; Foulkes, William D

2008-01-01

Background BRCA1 and BRCA2 account for the majority of the known familial breast cancer risk, however, the impact of other cancer susceptibility genes largely remains to be elucidated. Checkpoint Kinase 2 (CHEK2) is an important signal transducer of cellular responses to DNA damage, whose defects have been associated with an increase in breast cancer risk. Previous studies have identified low penetrance CHEK2 alleles such as 1100delC and I157T, as well as variants such as S428F in the Ashkenazi Jewish population and IVS2 + 1G>A in the Polish population. No founder allele has been specifically identified in the French Canadian population. Methods The 14 coding exons of CHEK2 were fully sequenced for variant alleles in a panel of 25 affected French Canadian women and 25 healthy controls. Two variants were identified of which one novel variant was further screened for in an additional panel of 667 breast cancer patients and 6548 healthy controls. Additional genotyping was conducted using allele specific PCR and a restriction digest assay. Significance of amino acid substitutions were deduced by employing comparative analysis techniques. Results Two variants were identified: the previously reported silent substitution 252A>G (E84E) and the novel missense variant, 1217G>A (R406H). No significant difference in allele distribution between French Canadian women with breast cancer and healthy controls was observed (3/692, 0.43% vs. 22/6573, 0.33%, respectively, P = 0.73). Conclusion The novel CHEK2 missense variant identified in this study, R406H, is unlikely to contribute to breast cancer risk in French Canadian women. PMID:18706089

Foam metal metamaterial panel for mechanical waves isolation

NASA Astrophysics Data System (ADS)

Hua, Lei; Sun, Hongwei; Gu, Jinliang

2016-04-01

This paper presents modeling, analysis techniques and experiment of foam metal metamaterial panel for Broadband Vibration Absorption. For a unit cell of an infinite foam metal metamaterial panel, governing equations are derived using the extended Hamilton principle. The concepts of negative effective mass and stiffness and how the spring-mass-damper subsystems create a stopband are explained in detail. Numerical simulations reveal that the actual working mechanism of the proposed metamaterial panel is based on the concept of conventional mechanical vibration absorbers. It uses the incoming elastic wave in the panel to resonate the integrated membrane-mass-damper absorbers to vibrate in their optical mode at frequencies close to but above their local resonance frequencies to create shear forces and bending moments to straighten the panel and stop the wave propagation. Moreover, a two-dimension acoustic foam metal metamaterial panel consisting of lumped mass and elastic membrane is proposed in the lab. We do experiments on the model and The results validate the concept and show that, for two-dimension acoustic foam metal metamaterial panel do exist two vibration modes. For the wave absorption, the mass of each cell should be considered in the design. With appropriate design calculations, the proposed two-dimension acoustic foam metal metamaterial panel can be used for absorption of low-frequency waves and hence expensive micro-manufacturing techniques are not needed for design and manufacturing of such foam metal metamaterial panel for low-frequency waves absorption/isolation.

Comprehensive review of the evidence regarding the effectiveness of community–based primary health care in improving maternal, neonatal and child health: 8. summary and recommendations of the Expert Panel

PubMed Central

Black, Robert E; Taylor, Carl E; Arole, Shobha; Bang, Abhay; Bhutta, Zulfiqar A; Chowdhury, A Mushtaque R; Kirkwood, Betty R; Kureshy, Nazo; Lanata, Claudio F; Phillips, James F; Taylor, Mary; Victora, Cesar G; Zhu, Zonghan; Perry, Henry B

2017-01-01

Background The contributions that community–based primary health care (CBPHC) and engaging with communities as valued partners can make to the improvement of maternal, neonatal and child health (MNCH) is not widely appreciated. This unfortunate reality is one of the reasons why so few priority countries failed to achieve the health–related Millennium Development Goals by 2015. This article provides a summary of a series of articles about the effectiveness of CBPHC in improving MNCH and offers recommendations from an Expert Panel for strengthening CBPHC that were formulated in 2008 and have been updated on the basis of more recent evidence. Methods An Expert Panel convened to guide the review of the effectiveness of community–based primary health care (CBPHC). The Expert Panel met in 2008 in New York City with senior UNICEF staff. In 2016, following the completion of the review, the Panel considered the review’s findings and made recommendations. The review consisted of an analysis of 661 unique reports, including 583 peer–reviewed journal articles, 12 books/monographs, 4 book chapters, and 72 reports from the gray literature. The analysis consisted of 700 assessments since 39 were analyzed twice (once for an assessment of improvements in neonatal and/or child health and once for an assessment in maternal health). Results The Expert Panel recommends that CBPHC should be a priority for strengthening health systems, accelerating progress in achieving universal health coverage, and ending preventable child and maternal deaths. The Panel also recommends that expenditures for CBPHC be monitored against expenditures for primary health care facilities and hospitals and reflect the importance of CBPHC for averting mortality. Governments, government health programs, and NGOs should develop health systems that respect and value communities as full partners and work collaboratively with them in building and strengthening CBPHC programs – through engagement with planning, implementation (including the full use of community–level workers), and evaluation. CBPHC programs need to reach every community and household in order to achieve universal coverage of key evidence–based interventions that can be implemented in the community outside of health facilities and assure that those most in need are reached. Conclusions Stronger CBPHC programs that foster community engagement/empowerment with the implementation of evidence–based interventions will be essential for achieving universal coverage of health services by 2030 (as called for by the Sustainable Development Goals recently adopted by the United Nations), ending preventable child and maternal deaths by 2030 (as called for by the World Health Organization, UNICEF, and many countries around the world), and eventually achieving Health for All as envisioned at the International Conference on Primary Health Care in 1978. Stronger CBPHC programs can also create entry points and synergies for expanding the coverage of family planning services as well as for accelerating progress in the detection and treatment of HIV/AIDS, tuberculosis, malaria, hypertension, and other chronic diseases. Continued strengthening of CBPHC programs based on rigorous ongoing operations research and evaluation will be required, and this evidence will be needed to guide national and international policies and programs. PMID:28685046

Modeling and Control of the Redundant Parallel Adjustment Mechanism on a Deployable Antenna Panel

PubMed Central

Tian, Lili; Bao, Hong; Wang, Meng; Duan, Xuechao

2016-01-01

With the aim of developing multiple input and multiple output (MIMO) coupling systems with a redundant parallel adjustment mechanism on the deployable antenna panel, a structural control integrated design methodology is proposed in this paper. Firstly, the modal information from the finite element model of the structure of the antenna panel is extracted, and then the mathematical model is established with the Hamilton principle; Secondly, the discrete Linear Quadratic Regulator (LQR) controller is added to the model in order to control the actuators and adjust the shape of the panel. Finally, the engineering practicality of the modeling and control method based on finite element analysis simulation is verified. PMID:27706076

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anggoro, Didi Dwi, E-mail: anggorophd@gmail.com; Kristiana, Nunung, E-mail: nuna.c631@gmail.com

Ballistic protection equipment, such as a bulletproof vest, is a soldier’s most important means of preserving life and survivability in extreme combat conditions. The bulletproof vests are designed to protect the user’s chest from injury without disturbing the ability to perform his duties. Aromatic polyamide or aramid fibers known under the trade name Kevlar, Trawon and so is synthetic fiber materials commonly used in the manufacture of bulletproof vests. This synthetic fibers have high tensile strength and ductility. Kevlar is expensive and imported material. In this study, will introduce local natural raw materials, ramie fiber (Boehmeria nivea) which is cheapermore » and environmentally friendly. It has enough tenacity and tensile strength as a bulletproof vest. This experiment uses two panels, there are Panel A as front surface of Panel B. Panel A is a combination of ramie and epoxide matrix, while panel B is only ramie. From several variations of experimental combinations between Panel A and Panel B, optimal combination obtained with 16 layers of panel A and 31-34 layers of panel B which is able to protect againts cal. 7.65 mm × 17 mm (.32 ACP) bullet fired through pistol .32 Pindad from a distance of 20 meters. Panel with a size of 20 cm × 20 cm has a total thickness between 12,922 to13,745 mm and a total weight between 506,26 to 520,926gram. Scanning electron microscopy (SEM) observations indicated that the porosity and surface area of the ramie fiber is smooth, fiber surfaces showed topography with micropores. SEM also showed well-arranged structure of fibers bonding. Energy Dispersive X-ray (EDX) analysis indicated 100 % carbon contents in ramie fiber. Test result indicates that panel from composite ramie-epoxide can reach the level 1of International Standard of NIJ - 010104. Compared to panel from polyester fiber, the panel from composite ramie-epoxide (0,50-0,52 kg) is lighter weight than panel polyester fiber (1,642 kg)« less

Combination of natural fiber Boehmeria nivea (ramie) with matrix epoxide for bullet proof vest body armor

NASA Astrophysics Data System (ADS)

Anggoro, Didi Dwi; Kristiana, Nunung

2015-12-01

Ballistic protection equipment, such as a bulletproof vest, is a soldier's most important means of preserving life and survivability in extreme combat conditions. The bulletproof vests are designed to protect the user's chest from injury without disturbing the ability to perform his duties. Aromatic polyamide or aramid fibers known under the trade name Kevlar, Trawon and so is synthetic fiber materials commonly used in the manufacture of bulletproof vests. This synthetic fibers have high tensile strength and ductility. Kevlar is expensive and imported material. In this study, will introduce local natural raw materials, ramie fiber (Boehmeria nivea) which is cheaper and environmentally friendly. It has enough tenacity and tensile strength as a bulletproof vest. This experiment uses two panels, there are Panel A as front surface of Panel B. Panel A is a combination of ramie and epoxide matrix, while panel B is only ramie. From several variations of experimental combinations between Panel A and Panel B, optimal combination obtained with 16 layers of panel A and 31-34 layers of panel B which is able to protect againts cal. 7.65 mm × 17 mm (.32 ACP) bullet fired through pistol .32 Pindad from a distance of 20 meters. Panel with a size of 20 cm × 20 cm has a total thickness between 12,922 to13,745 mm and a total weight between 506,26 to 520,926gram. Scanning electron microscopy (SEM) observations indicated that the porosity and surface area of the ramie fiber is smooth, fiber surfaces showed topography with micropores. SEM also showed well-arranged structure of fibers bonding. Energy Dispersive X-ray (EDX) analysis indicated 100 % carbon contents in ramie fiber. Test result indicates that panel from composite ramie-epoxide can reach the level 1of International Standard of NIJ - 010104. Compared to panel from polyester fiber, the panel from composite ramie-epoxide (0,50-0,52 kg) is lighter weight than panel polyester fiber (1,642 kg).

Attitude and vibration control of a satellite containing flexible solar arrays by using reaction wheels, and piezoelectric transducers as sensors and actuators

NASA Astrophysics Data System (ADS)

da Fonseca, Ijar M.; Rade, Domingos A.; Goes, Luiz C. S.; de Paula Sales, Thiago

2017-10-01

The primary purpose of this paper is to provide insight into control-structure interaction for satellites comprising flexible appendages and internal moving components. The physical model considered herein aiming to attend such purpose is a rigid-flexible satellite consisting of a rigid platform containing two rotating flexible solar panels. The solar panels rotation is assumed to be in a sun-synchronous configuration mode. The panels contain surface-bonded piezoelectric patches that can be used either as sensors for the elastic displacements or as actuators to counteract the vibration motion. It is assumed that in the normal mode operation the satellite platform points towards the Earth while the solar arrays rotate so as to follow the Sun. The vehicle moves in a low Earth polar orbit. The technique used to obtain the mathematical model combines the Lagrangian formulation with the Finite Elements Method used to describe the dynamics of the solar panel. The gravity-gradient torque as well as the torque due to the interaction of the Earth magnetic field and the satellite internal residual magnetic moment is included as environmental perturbations. The actuators are three reaction wheels for attitude control and piezoelectric actuators to control the flexible motion of the solar arrays. Computer simulations are performed using the MATLAB® software package. The following on-orbit satellite operating configurations are object of analysis: i) Satellite pointing towards the Earth (Earth acquisition maneuver) by considering the initial conditions in the elastic displacement equal to zero, aiming the assessment of the flexible modes excitation by the referred maneuver; ii) the satellite pointing towards the Earth with the assumption of an initial condition different from zero for the flexible motion such that the attitude alterations are checked against the elastic motion disturbance; and iii) attitude acquisition accomplished by taking into account initial conditions different from zero for both attitude and elastic vibrations. Additionally, the control efforts for the three cases are compared. Results indicate that the attitude control is able to excite the solar panels' vibration modes and vice-versa. The piezoelectric vibration control shows significant performance improvement when compared to contributions of the attitude control to the vibration damping.

Flow distribution analysis on the cooling tube network of ITER thermal shield

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nam, Kwanwoo; Chung, Wooho; Noh, Chang Hyun

2014-01-29

Thermal shield (TS) is to be installed between the vacuum vessel or the cryostat and the magnets in ITER tokamak to reduce the thermal radiation load to the magnets operating at 4.2K. The TS is cooled by pressurized helium gas at the inlet temperature of 80K. The cooling tube is welded on the TS panel surface and the composed flow network of the TS cooling tubes is complex. The flow rate in each panel should be matched to the thermal design value for effective radiation shielding. This paper presents one dimensional analysis on the flow distribution of cooling tube networkmore » for the ITER TS. The hydraulic cooling tube network is modeled by an electrical analogy. Only the cooling tube on the TS surface and its connecting pipe from the manifold are considered in the analysis model. Considering the frictional factor and the local loss in the cooling tube, the hydraulic resistance is expressed as a linear function with respect to mass flow rate. Sub-circuits in the TS are analyzed separately because each circuit is controlled by its own control valve independently. It is found that flow rates in some panels are insufficient compared with the design values. In order to improve the flow distribution, two kinds of design modifications are proposed. The first one is to connect the tubes of the adjacent panels. This will increase the resistance of the tube on the panel where the flow rate is excessive. The other design suggestion is that an orifice is installed at the exit of tube routing where the flow rate is to be reduced. The analysis for the design suggestions shows that the flow mal-distribution is improved significantly.« less