Science.gov

Sample records for pca steel alloy

  1. High strength, tough alloy steel

    DOEpatents

    Thomas, Gareth; Rao, Bangaru V. N.

    1979-01-01

    A high strength, tough alloy steel is formed by heating the steel to a temperature in the austenite range (1000.degree.-1100.degree. C.) to form a homogeneous austenite phase and then cooling the steel to form a microstructure of uniformly dispersed dislocated martensite separated by continuous thin boundary films of stabilized retained austenite. The steel includes 0.2-0.35 weight % carbon, at least 1% and preferably 3-4.5% chromium, and at least one other substitutional alloying element, preferably manganese or nickel. The austenite film is stable to subsequent heat treatment as by tempering (below 300.degree. C.) and reforms to a stable film after austenite grain refinement.

  2. Braze alloy spreading on steel

    NASA Technical Reports Server (NTRS)

    Siewert, T. A.; Heine, R. W.; Lagally, M. G.

    1978-01-01

    Scanning electron microscopy (SEM) and Auger electron microscopy (AEM) were employed to observe elemental surface decomposition resulting from the brazing of a copper-treated steel. Two types of steel were used for the study, stainless steel (treated with a eutectic silver-copper alloy), and low-carbon steel (treated with pure copper). Attention is given to oxygen partial pressure during the processes; a low enough pressure (8 x 10 to the -5th torr) was found to totally inhibit the spreading of the filler material at a fixed heating cycle. With both types of steel, copper treatment enhanced even spreading at a decreased temperature.

  3. Innovative Comparison of Transient Ignition Temperature at the Booster Interface, New Stainless Steel Pyrovalve Primer Chamber Assembly "V" (PCA) Design Versus the Current Aluminum "Y" PCA Design

    NASA Technical Reports Server (NTRS)

    Saulsberry, Regor L.; McDougle, Stephen H.; Garcia,Roberto; Johnson, Kenneth L.; Sipes, William; Rickman, Steven; Hosangadi, Ashvin

    2011-01-01

    An assessment of four spacecraft pyrovalve anomalies that occurred during ground testing was conducted by the NASA Engineering & Safety Center (NESC) in 2008. In all four cases, a common aluminum (Al) primer chamber assembly (PCA) was used with dual NASA Standard Initiators (NSIs) and the nearly simultaneous (separated by less than 80 microseconds) firing of both initiators failed to ignite the booster charge. The results of the assessment and associated test program were reported in AIAA Paper AIAA-2008-4798, NESC Independent Assessment of Pyrovalve Ground Test Anomalies. As a result of the four Al PCA anomalies, and the test results and findings of the NESC assessment, the Mars Science Laboratory (MSL) project team decided to make changes to the PCA. The material for the PCA body was changed from aluminum (Al) to stainless steel (SS) to avoid melting, distortion, and potential leakage of the NSI flow passages when the device functioned. The flow passages, which were interconnected in a Y-shaped configuration (Y-PCA) in the original design, were changed to a V-shaped configuration (V-PCA). The V-shape was used to more efficiently transfer energy from the NSIs to the booster. Development and qualification testing of the new design clearly demonstrated faster booster ignition times compared to the legacy AL Y-PCA design. However, the final NESC assessment report recommended that the SS V-PCA be experimentally characterized and quantitatively compared to the Al Y-PCA design. This data was deemed important for properly evaluating the design options for future NASA projects. This test program has successfully quantified the improvement of the SS V-PCA over the Al Y-PCA. A phase B of the project was also conducted and evaluated the effect of firing command skew and enlargement of flame channels to further assist spacecraft applications.

  4. Alloy dissolution in argon stirred steel

    NASA Astrophysics Data System (ADS)

    Webber, Darryl Scott

    Alloying is required for the production of all steel products from small castings to large beams. Addition of large quantities of bulk alloys can result in alloy segregation and inconsistent alloy recovery. The objective of this research was to better understand alloy dissolution in liquid steel especially as it relates to Missouri S&Ts' patented continuous steelmaking process. A 45-kilogram capacity ladle with a single porous plug was used to evaluate the effect of four experimental factors on alloy dissolution: alloy species, alloy size or form, argon flow rate, and furnace tap temperature. Four alloys were tested experimentally including Class I low carbon ferromanganese, nickel and tin (as a surrogate for low melting alloys) and Class II ferroniobium. The alloys ranged in size and form from granular to 30 mm diameter lumps. Experimental results were evaluated using a theoretically based numerical model for the steel shell period, alloy mixing (Class I) and alloy dissolution (Class II). A CFD model of the experimental ladle was used to understand steel motion in the ladle and to provide steel velocity magnitudes for the numerical steel shell model. Experiments and modeling confirmed that smaller sized alloys have shorter steel shell periods and homogenize faster than larger particles. Increasing the argon flow rate shortened mixing times and reduced the delay between alloy addition and the first appearance of alloy in the melt. In addition, for every five degree increase in steel bath temperature the steel shell period was shortened by approximately four percent. Class II ferroniobium alloy dissolution was an order of magnitude slower than Class I alloy mixing.

  5. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  6. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  7. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  8. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  9. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  10. Direct Alloying of Steel with Nickel Concentrate

    NASA Astrophysics Data System (ADS)

    Nokhrina, O. I.; Rozhikhina, I. D.; Proshunin, I. E.

    2016-08-01

    A technology of alloying steel with nickel reduced from nickel concentrate is analysed and developed. Limits of reduction concentration areas are defined. An optimal composition of nickel concentrate pellets and a method of feeding them into the furnace are deduced from experiments. It is proved that when pellets made of nickel concentrate and coke are added into the charge during steel smelting by the technology of alloyed scrap remelting, nickel recovery achieves 92-95%. The technology was tested by smelting DSP-40 steel.

  11. Tungsten carbide laser alloying of a low alloyed steel

    NASA Astrophysics Data System (ADS)

    Cojocaru, Mihai; Taca, Mihaela

    1996-10-01

    Laser alloying is a way to change the composition of metal surfaces in order to improve their corrosion-resistance, high-temperature strength and hardness. The results of a structural and phase analysis of a tungsten carbide based surface layer prepared by laser alloying of a low carbon steel substrate are presented. Structure, phase composition and microhardness of surface alloyed layers have been investigated. The surface of the samples exhibited a thin layer with a different chemical and phase composition. An increase in alloyed surface hardness and wear-resistance was observed.

  12. Welding of Aluminum Alloys to Steels: An Overview

    DTIC Science & Technology

    2013-08-01

    95] K. Kimapong1, T. Watanabe, Effect of welding process parameters on mechanical property of FSW lap joint between aluminum alloy and steel ...UNCLASSIFIED: Distribution Statement A. Approved for public release. 1 UNCLASSIFIED Welding of aluminum alloys to steels : an overview M. Mazar...welding methods for joining aluminum alloys to steels . The microstructural development, mechanical properties and application of the joints are discussed

  13. Friction Stir Welding of Steel Alloys

    NASA Technical Reports Server (NTRS)

    Ding, R. Jeffrey; Munafo, Paul M. (Technical Monitor)

    2001-01-01

    The friction stir welding process has been developed primarily for the welding of aluminum alloys. Other higher melting allows such, as steels are much more difficult to join. Special attention must be given to pin tool material selection and welding techniques. This paper addresses the joining of steels and other high melting point materials using the friction stir welding process. Pin tool material and welding parameters will be presented. Mechanical properties of weldments will also be presented. Significance: There are many applications for the friction stir welding process other than low melting aluminum alloys. The FSW process can be expanded for use with high melting alloys in the pressure vessel, railroad and ship building industries.

  14. Tensile properties of unirradiated PCA from room temperature to 700/sup 0/C

    SciTech Connect

    Braski, D.N.; Maziasz, P.J.

    1983-01-01

    The tensile properties of Prime Candidate Alloy (PCA) austenitic stainless steel after three different thermomechanical treatments were determined from room temperature to 700/sup 0/C. The solution-annealed PCA had the lowest strength and highest ductility, while the reverse was true for the 25%-cold-worked material. The PCA containing titanium-rich MC particles fell between the other two heats. The cold-worked PCA had nearly the same tensile properties as cold-worked type 316 stainless steel. Both alloys showed ductility minima at 300/sup 0/C.

  15. Crack stability analysis of low alloy steel primary coolant pipe

    SciTech Connect

    Tanaka, T.; Kameyama, M.; Urabe, Y.

    1997-04-01

    At present, cast duplex stainless steel has been used for the primary coolant piping of PWRs in Japan and joints of dissimilar material have been applied for welding to reactor vessels and steam generators. For the primary coolant piping of the next APWR plants, application of low alloy steel that results in designing main loops with the same material is being studied. It means that there is no need to weld low alloy steel with stainless steel and that makes it possible to reduce the welding length. Attenuation of Ultra Sonic Wave Intensity is lower for low alloy steel than for stainless steel and they have advantageous inspection characteristics. In addition to that, the thermal expansion rate is smaller for low alloy steel than for stainless steel. In consideration of the above features of low alloy steel, the overall reliability of primary coolant piping is expected to be improved. Therefore, for the evaluation of crack stability of low alloy steel piping to be applied for primary loops, elastic-plastic future mechanics analysis was performed by means of a three-dimensioned FEM. The evaluation results for the low alloy steel pipings show that cracks will not grow into unstable fractures under maximum design load conditions, even when such a circumferential crack is assumed to be 6 times the size of the wall thickness.

  16. Amorphous Alloy Surpasses Steel and Titanium

    NASA Technical Reports Server (NTRS)

    2004-01-01

    In the same way that the inventions of steel in the 1800s and plastic in the 1900s sparked revolutions for industry, a new class of amorphous alloys is poised to redefine materials science as we know it in the 21st century. Welcome to the 3rd Revolution, otherwise known as the era of Liquidmetal(R) alloys, where metals behave similar to plastics but possess more than twice the strength of high performance titanium. Liquidmetal alloys were conceived in 1992, as a result of a project funded by the California Institute of Technology (CalTech), NASA, and the U.S. Department of Energy, to study the fundamentals of metallic alloys in an undercooled liquid state, for the development of new aerospace materials. Furthermore, NASA's Marshall Space Flight Center contributed to the development of the alloys by subjecting the materials to testing in its Electrostatic Levitator, a special instrument that is capable of suspending an object in midair so that researchers can heat and cool it in a containerless environment free from contaminants that could otherwise spoil the experiment.

  17. Radiation resistant austenitic stainless steel alloys

    DOEpatents

    Maziasz, P.J.; Braski, D.N.; Rowcliffe, A.F.

    1987-02-11

    An austenitic stainless steel alloy, with improved resistance to radiation-induced swelling and helium embrittlement, and improved resistance to thermal creep at high temperatures, consisting essentially of, by weight percent: from 16 to 18% nickel; from 13 to 17% chromium; from 2 to 3% molybdenum; from 1.5 to 2.5% manganese; from 0.01 to 0.5% silicon; from 0.2 to 0.4% titanium; from 0.1 to 0.2% niobium; from 0.1 to 0.6% vanadium; from 0.06 to 0.12% carbon; from 0.01 to 0.03% nitrogen; from 0.03 to 0.08% phosphorus; from 0.005 to 0.01% boron; and the balance iron, and wherein the alloy may be thermomechanically treated to enhance physical and mechanical properties. 4 figs.

  18. Radiation resistant austenitic stainless steel alloys

    DOEpatents

    Maziasz, Philip J.; Braski, David N.; Rowcliffe, Arthur F.

    1989-01-01

    An austenitic stainless steel alloy, with improved resistance to radiation-induced swelling and helium embrittlement, and improved resistance to thermal creep at high temperatures, consisting essentially of, by weight percent: from 16 to 18% nickel; from 13 to 17% chromium; from 2 to 3% molybdenum; from 1.5 to 2.5% manganese; from 0.01 to 0.5% silicon; from 0.2 to 0.4% titanium; from 0.1 to 0.2% niobium; from 0.1 to 0.6% vanadium; from 0.06 to 0.12% carbon; from 0.01% to 0.03% nitrogen; from 0.03 to 0.08% phosphorus; from 0.005 to 0.01% boron; and the balance iron, and wherein the alloy may be thermomechanically treated to enhance physical and mechanical properties.

  19. Feasibility of Underwater Friction Stir Welding of Hardenable Alloy Steel

    DTIC Science & Technology

    2010-12-01

    bead-on-plate FSW traverses, approximately 64 inches (1.6 m) in total length, on 0.25 inch (6.4 mm) thick plates of a hardenable alloy steel . The...base plate. Based on preliminary findings, FSW of hardenable alloy steel is a feasible process and should be further researched and refined. 15...v ABSTRACT The objective of this thesis is to determine whether friction stir welding ( FSW ) is a feasible welding process for steels in an

  20. Practical handbook of stainless steels and nickel alloys

    SciTech Connect

    Lamb, S.

    1999-07-01

    This new handbook is an up-to-date technical guide to the grades, properties, fabrication characteristics, and applications of stainless steels and nickel alloys. The individual chapters were written by industry experts and focus on the key properties and alloy characteristics important in material selection and specification as well as the practical factors that influence the development and application of these materials. The contents include: alloy grades and their welding and fabrication characteristics and their application; monel metal; iron-based and nickel-based alloys; ferritic, austenitic, superaustenitic, and martensitic stainless steels; hastelloys; alloys 20, G, and 825; AOD and new refining technology; duplex stainless steels; 6-Mo alloys; corrosion-resistant castings; specification cross-reference tables; trade names; hardness conversions; list of common abbreviations.

  1. Corrosion behavior of stainless steel-zirconium alloy waste forms.

    SciTech Connect

    Abraham, D. P.

    1999-01-13

    Stainless steel-zirconium (SS-Zr) alloys are being considered as waste forms for the disposal of metallic waste generated during the electrometallurgical treatment of spent nuclear fuel. The baseline waste form for spent fuels from the EBR-II reactor is a stainless steel-15 wt.% zirconium (SS-15Zr) alloy. This article briefly reviews the microstructure of various SS-Zr waste form alloys and presents results of immersion corrosion and electrochemical corrosion tests performed on these alloys. The electrochemical tests show that the corrosion behavior of SS-Zr alloys is comparable to those of other alloys being considered for the Yucca Mountain geologic repository. The immersion tests demonstrate that the SS-Zr alloys are resistant to selective leaching of fission product elements and, hence, suitable as candidates for high-level nuclear waste forms.

  2. A statistical model for cleavage fracture of low alloy steel

    SciTech Connect

    Chen, J.H.; Wang, G.Z.; Wang, H.J.

    1996-10-01

    A new statistical model for cleavage fracture of the low alloy steel is proposed. This model is based on a recently suggested physical model and takes account of the effect of the preceding loading processes. This statistical model satisfactorily describes the failure probability distribution of 42 precracked specimens fractured at various loads at a test temperature of {minus}100 C. The micromechanisms of cleavage fracture of low alloy steel are also further discussed.

  3. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  4. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  5. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  6. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  7. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  8. Comparative Structural Strength Research of Hardened Carbon Steel and Hot-Rolled Alloy Steel

    NASA Astrophysics Data System (ADS)

    Bogomolov, A. V.; Zhakupov, A. N.; Kanayev, A. T.; Sikach, I. A.; Tugumov, K. K.

    2016-08-01

    Experiments on quantitative evaluation of fatigue strength showed that St5ps and St5sp carbon steels with A400 strength class can be fully applied for erection of constructions and buildings having cyclical loads during operation. Study of corrosion resistance of hardened carbon steel in comparison with hot-rolled alloy steel consists in difference in structures and hence, difference in intensity of electric and chemical processes featuring presence of steel in concrete. Structure of St5sp steel with A400 strength class in surface area has significantly less corrosion rate than ferritic-perlitic structure of 35GS steel with A400 strength class.

  9. Materials data handbook: Stainless steel alloy A-286

    NASA Technical Reports Server (NTRS)

    Muraca, R. F.; Whittick, J. S.

    1972-01-01

    A summary of the materials property information for stainless steel alloy A-286 is presented. The scope of the information includes physical and mechanical properties at cryogenic, ambient, and elevated temperatures. Information on material procurement, metallurgy of the alloy, corrosion, environmental effects, fabrication, and bonding is developed.

  10. The Austenitizing Behavior of a Low Alloy Steel

    DTIC Science & Technology

    1980-05-01

    to differences in melting and solidification between the two types of steels ; ESR exhibiting a more uniform dendritic grain structure and possibly...AD-AoVtS^ MCHNICAi; LIBRARY AD TECHNICAL REPORT ARLCB-TR-80013 TIE AUSIENITIZING BEHAVIOR OF A LDW ALLDY STEEL P, A. Thornton May 1980 US...Behavior of a Low Alloy Steel 5. TYPE OF REPORT 4 PERIOD COVERED 6. PERFORMING ORG. REPORT NUMBER 7. AUTHORf*; 8. CONTRACT OR GRANT NUMBERf*) Peter A

  11. ASM Specialty Handbook{reg_sign}: Carbon and alloy steels

    SciTech Connect

    Davis, J.R.

    1995-12-31

    Carbon and alloy steels are the workhorse of structural materials in modern engineering because of their very reasonable costs coupled with their many and varied properties that allow their use in such a large array of applications. it`s very easy to take steel for granted and forget how much it`s relied upon in critical uses such as cars, bridges, buildings, landing gear assemblies, and more. There are in-depth reviews on formability weldability, machineability, and hardenability of the various steel grades. One can also discover how adding certain alloys can significantly improve steel processing. The strength and toughness section has been greatly expanded with more coverage than ever before of corrosion fatigue. One has access to extensive reports detailing which steels are more susceptible to environmental damage such as stress-corrosion and hydrogen embrittlement. Temperature effects relating to mechanical properties and corrosion are also discussed.

  12. Milling and Drilling Evaluation of Stainless Steel Powder Metallurgy Alloys

    SciTech Connect

    Lazarus, L.J.

    2001-12-10

    Near-net-shape components can be made with powder metallurgy (PM) processes. Only secondary operations such as milling and drilling are required to complete these components. In the past and currently production components are made from powder metallurgy (PM) stainless steel alloys. process engineers are unfamiliar with the difference in machining properties of wrought versus PM alloys and have had to make parts to develop the machining parameters. Design engineers are not generally aware that some PM alloy variations can be furnished with machining additives that greatly increase tool life. Specimens from a MANTEC PM alloy property study were made available. This study was undertaken to determine the machining properties of a number of stainless steel wrought and PM alloys under the same conditions so that comparisons of their machining properties could be made and relative tool life determined.

  13. Method of making high strength, tough alloy steel

    DOEpatents

    Thomas, Gareth; Rao, Bangaru V. N.

    1979-01-01

    A high strength, tough alloy steel, particularly suitable for the mining industry, is formed by heating the steel to a temperature in the austenite range (1000.degree.-1100.degree. C.) to form a homogeneous austenite phase and then cooling the steel to form a microstructure of uniformly dispersed dislocated martensite separated by continuous thin boundary films of stabilized retained austenite. The steel includes 0.2-0.35 weight % carbon, at least 1% and preferably 3-4.5% chromium, and at least one other subsitutional alloying element, preferably manganese or nickel. The austenite film is stable to subsequent heat treatment as by tempering (below 300.degree. C.) and reforms to a stable film after austenite grain refinement.

  14. Laves intermetallics in stainless steel-zirconium alloys

    SciTech Connect

    Abraham, D.P.; McDeavitt, S.M.; Richardson, J.W. Jr.

    1997-05-01

    Laves intermetallics have a significant effect on properties of metal waste forms being developed at Argonne National Laboratory. These waste forms are stainless steel-zirconium alloys that will contain radioactive metal isotopes isolated from spent nuclear fuel by electrometallurgical treatment. The baseline waste form composition for stainless steel-clad fuels is stainless steel-15 wt.% zirconium (SS-15Zr). This article presents results of neutron diffraction measurements, heat-treatment studies and mechanical testing on SS-15Zr alloys. The Laves intermetallics in these alloys, labeled Zr(Fe,Cr,Ni){sub 2+x}, have both C36 and C15 crystal structures. A fraction of these intermetallics transform into (Fe,Cr,Ni){sub 23}Zr{sub 6} during high-temperature annealing; the authors have proposed a mechanism for this transformation. The SS-15Zr alloys show virtually no elongation in uniaxial tension, but exhibit good strength and ductility in compression tests. This article also presents neutron diffraction and microstructural data for a stainless steel-42 wt.% zirconium (SS-42Zr) alloy.

  15. Stress-corrosion crack-growth study of titanium alloy Ti-6Al-4V exposed to freon PCA and nitrogen tetroxide MON-1

    NASA Technical Reports Server (NTRS)

    Bjorklund, R. A.

    1983-01-01

    An experimental fracture mechanics program was performed to determine the stress corrosion crack growth sensitivity of the propellant tank material, titanium alloy Ti-6Al-4V, for aerospace satellite applications involving long term exposure to Freon PCA and nitrogen tetroxide MON-1. Sustained load tests were made at a 49 C (120 F) constant temperature using thin gauge tensile test specimens containing semielliptical surface flaws. Test specimen types included parent metal, center of weld, and weld heat affected zone. It was concluded that Ti-6Al-4V alloy is not adversely affected in a stress environment when exposed to Freon PCA for 1000 hours followed by exposure to nitrogen tetroxide MON-1 for 2000 hours at stress levels up to 80% of the experimental critical plane strain stress intensity factor.

  16. 76 FR 36086 - Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-21

    ... International Trade Administration Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Final Results of... welded non- alloy steel pipe from Mexico. See Certain Circular Welded Non-Alloy Steel Pipe From Mexico... Antidumping Duty Changed Circumstances Review: Certain Circular Welded Non-Alloy Steel Pipe from Mexico, 75...

  17. Process for making a martensitic steel alloy fuel cladding product

    DOEpatents

    Johnson, Gerald D.; Lobsinger, Ralph J.; Hamilton, Margaret L.; Gelles, David S.

    1990-01-01

    This is a very narrowly defined martensitic steel alloy fuel cladding material for liquid metal cooled reactors, and a process for making such a martensitic steel alloy material. The alloy contains about 10.6 wt. % chromium, about 1.5 wt. % molybdenum, about 0.85 wt. % manganese, about 0.2 wt. % niobium, about 0.37 wt. % silicon, about 0.2 wt. % carbon, about 0.2 wt. % vanadium, 0.05 maximum wt. % nickel, about 0.015 wt. % nitrogen, about 0.015 wt. % sulfur, about 0.05 wt. % copper, about 0.007 wt. % boron, about 0.007 wt. % phosphorous, and with the remainder being essentially iron. The process utilizes preparing such an alloy and homogenizing said alloy at about 1000.degree. C. for 16 hours; annealing said homogenized alloy at 1150.degree. C. for 15 minutes; and tempering said annealed alloy at 700.degree. C. for 2 hours. The material exhibits good high temperature strength (especially long stress rupture life) at elevated temperature (500.degree.-760.degree. C.).

  18. Low Mn alloy steel for cryogenic service

    DOEpatents

    Morris, J.W. Jr.; Niikura, M.

    A ferritic cryogenic steel which has a relatively low (about 4 to 6%) manganese content and which has been made suitable for use at cryogenic temperatures by a thermal cycling treatment followed by a final tempering. The steel includes 4 to 6% manganese, 0.02 to 0.06% carbon, 0.1 to 0.4% molybdenum and 0 to 3% nickel.

  19. Barnacle-induced corrosion of high-alloyed steels

    SciTech Connect

    Koryakova, M.D.; Filonenko, N.Yu.; Kaplin, Yu.M.

    1995-03-01

    Local corrosion of two sorts of high-alloyed steels under the action of acorn barnacles (Balanuses) has been studied. It has been shown that in natural seawater at anaerobic conditions beneath living and dead barnacles, metabolic activity of bacteria may be considered as a primary cause for local surface depassivation.

  20. Thermophysical property measurements on low alloy high strength carbon steels

    SciTech Connect

    Li, M.; Brooks, J.A.; Atteridge, D.G.; Porter, W.D.

    1997-06-15

    The alloys of interest in this study were AISI Type 4230 and Type 4320 low alloy high strength carbon steels. They are heat-treatable steels and are usually used in the quenched and tempered condition. The Type 4130 has about 0.3% (wt.)C, 0.95%Cr, and 0.2% Mo. The Type 4320 has about 0.2%C, 1.7%Ni, 0.7%Cr, and 0.3% Mo. They are among the most popular alloy steels because of their excellent combination of mechanical properties and are used in both cast and wrought forms for many applications requiring high strength and toughness. However, during the casting operation, carbon segregation to the part surface forms a high carbon content surface layer in the part, which will induce surface cracking in the subsequent quenching process. And, during the welding operation, the critical cooling rate in the heat-affected zone (HAZ) will determine if the weldment is crack-free or not. Thus, the numerical effort to study the thermal history, microstructure evolution and residual stress development during welding and casting is critical to the application of these steels. This modeling effect requires the accurate knowledge of thermophysical properties, such as thermal expansion, solidus and liquidus temperatures, specific heat capacity, and heat of fusion. Unfortunately, these thermophysical properties are unavailable for temperatures over 1,000 C (1,2), thus the need for this study.

  1. 77 FR 54926 - Certain Seamless Carbon and Alloy Steel; Standard, Line, and Pressure Pipe From Germany

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-06

    ... COMMISSION Certain Seamless Carbon and Alloy Steel; Standard, Line, and Pressure Pipe From Germany... steel standard, line, and pressure pipe from Germany would be likely to lead to continuation or... 2012), entitled Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from...

  2. 75 FR 26273 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-11

    ... COMMISSION Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From China AGENCY...-fair-value imports from China of certain seamless carbon and alloy steel standard, line, and pressure... than stainless steel) standard, line, and pressure pipes produced to the ASTM A-53, ASTM A-106, ASTM...

  3. 75 FR 21658 - Carbon and Certain Alloy Steel Wire Rod From Trinidad and Tobago

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-26

    ... COMMISSION Carbon and Certain Alloy Steel Wire Rod From Trinidad and Tobago AGENCY: United States... in the antidumping duty Investigation No. 731-TA-961 concerning carbon and certain alloy steel wire... known as Mittal Steel Point Lisas, Ltd., initiated a judicial action to review the...

  4. Influence of alloying elements on corrosion resistance of low alloy steels in marine environment

    SciTech Connect

    Wei, F.I.

    1995-09-01

    Most area of the earth is ocean. Therefore, exploitation of marine resources and utilization of marine space rapidly increase in recent years. Most of marine structures, such as wharfs, oil drilling platforms, coastal bridges, airports, etc. are mainly constructed by steel. It is therefore very important to develop marine corrosion resistant steels that do not require protection and are inexpensive. In this study, a series of low alloy steels were prepared by the method of experimental design as well as conventional design to study the effects of alloying elements on the marine corrosion resistance, under consideration of the requirement of mechanical properties. All steels were cyclically dipped to synthetic sea water in the laboratory for 7 weeks or exposed in the Taichung Harbor for more than 4 years. Both test results show similar tendency of the effects of alloying elements, but the effects of fouling on pitting were only observed in the latter. Addition of phosphorus and copper can improve the general corrosion resistance in atmospheric splash zone and titanium has the same effect in sea water. Molybdenum can improve the general corrosion resistance in both splash and tidal zones and pitting resistance in tidal and submerged zones. Due to enrichment of the alloying elements in the rust resulting in development of inner dense rust layer and change of rust composition, the anti-corrosion ability of most designed steels can be enhanced in marine environment. In addition, the corrosion resistance of most tested steels is superior to plain carbon steel (A-36) and weathering steel (Acr-Ten A) in Taichung Harbor.

  5. Evaluation and control of environmental corrosion for aluminum and steel alloys

    NASA Technical Reports Server (NTRS)

    Franklin, D. B.

    1977-01-01

    Corrosion protection systems for aerospace application and the effects of surface treatments and methods of controlling stress corrosion are evaluated. Chromate pigmented systems were found to be most effective for aluminum alloys; zinc-rich coatings gave the greatest protection to steel alloys. Various steel and aluminum alloys are rated for stress corrosion resistance.

  6. Improved Heat Treatment Of Steel Alloy 4340

    NASA Technical Reports Server (NTRS)

    Cooper, Lawrence B.

    1993-01-01

    New process takes significantly less time than prior heat-treatment processes. Involves placing steel plate directly in furnace and heat-treating. Plate then quenched in slowly moving oil to reduce stresses. Any deflection then pressed out. Possible uses of 4340 steel include new and improved bulletproof vests for military and police personnel and armor for bulletproof automobiles for military, police, diplomatic, and private users. Also used in other military land vehicles as tanks and in both military and civilian aircraft. Lighter armorplate enables land vehicles and aircraft to attain greater speed and maneuverability, consume less fuel, and afford better protection from snipers or terrorists.

  7. 78 FR 76653 - Carbon and Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico, Moldova, Trinidad and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-18

    ... Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico, Moldova, Trinidad and Tobago, and Ukraine... steel ] wire rod from Brazil and the antidumping duty orders on carbon and certain alloy steel wire rod... wire rod from Brazil and the antidumping duty orders on carbon and certain alloy steel wire rod...

  8. Frictional conditions between alloy AA6060 aluminium and tool steel

    SciTech Connect

    Wideroee, Fredrik; Welo, Torgeir

    2011-05-04

    The frictional conditions in the new process of screw extrusion of aluminium have been investigated. The contact behaviour between the aluminum alloy and the tool steel in the extruder is vital for understanding the extrusion process. Using a compressive-rotational method for frictional measurements the conditions for unlubricated sticking friction between aluminum alloy AA6060 and tool steel at different combinations of temperatures and pressures have been investigated. In this method the samples in the form of disks are put under hydrostatic pressure while simultaneously being rotated at one end. Pins made from contrast material have been inserted into the samples to measure the deformation introduced. This approach along with 3D simulations form a method for determining the frictional conditions. The paper describes the test method and the results. It was found that the necessary pressure for sticking to occur between the aluminum AA6060 and the different parts of the extruder is heavily influenced by the temperature.

  9. Gas-Carburizing Kinetics of a Low-Alloy Steel

    NASA Astrophysics Data System (ADS)

    Nobili, Luca; Cavallotti, Pietro; Pesetti, Mariella

    2010-02-01

    Gas-carburizing kinetics of a low-alloy steel (Pyrowear 53) was investigated by thermogravimetric experiments. Kinetic curves were modeled by adapting the approximate integral method, and the diffusion coefficient of carbon as well as the rate constant of the surface reaction were estimated. These parameters were evaluated after several carburizing procedures, which differ from each other in the surface treatments performed before the carburizing step. It is known that the carbon enrichment is low when this steel is carburized without any pretreatment, and this behavior was found to be related to a low value of carbon diffusivity. The interaction between the selective oxidation of alloying elements by the carburizing atmosphere and carbon diffusion is discussed. The pretreatment procedures investigated in this work consist of different combinations of oxidation, reduction, and grit-blasting processes. The most effective procedures involve oxidation in dry air or oxidation in wet air followed by grit blasting.

  10. [The LIBS experiment condition optimization of alloy steel].

    PubMed

    Shao, Yan; Gao, Xun; Du, Chuang; Zhao, Zhen-Ming; Chen, Wei-Yu; Hao, Zuo-Qiang; Sun, Chang-Kai; Lin, Jing-Quan

    2013-02-01

    Laser induced plasma spectroscopy of alloy steel was produced by Nd : YAG pulsed laser at 1 064 nm, and the spectral signal was detected by high resolution and width controlled ICCD. Several Fe atomic spectral lines such as 404.581, 414.387, 427.176 and 438.355 nm were chosen for analysis, and the effects of different experimental parameters on LIBS spectral signal intensity were investigated. It is shown that the experimental parameters such as pulse energy, laser focus location and laser delay time have great influence on the LIBS signal. LIBS signals with high spectral intensity and signal-background ratio (SBR) as well as the optimum experiment conditions were obtained by optimizing these experiment parameters so as to make composition analysis of the alloy steel.

  11. Method of polishing nickel-base alloys and stainless steels

    DOEpatents

    Steeves, Arthur F.; Buono, Donald P.

    1981-01-01

    A chemical attack polish and polishing procedure for use on metal surfaces such as nickel base alloys and stainless steels. The chemical attack polish comprises Fe(NO.sub.3).sub.3, concentrated CH.sub.3 COOH, concentrated H.sub.2 SO.sub.4 and H.sub.2 O. The polishing procedure includes saturating a polishing cloth with the chemical attack polish and submicron abrasive particles and buffing the metal surface.

  12. Attack polish for nickel-base alloys and stainless steels

    DOEpatents

    Steeves, Arthur F.; Buono, Donald P.

    1983-01-01

    A chemical attack polish and polishing procedure for use on metal surfaces such as nickel base alloys and stainless steels. The chemical attack polish comprises Fe(NO.sub.3).sub.3, concentrated CH.sub.3 COOH, concentrated H.sub.2 SO.sub.4 and H.sub.2 O. The polishing procedure includes saturating a polishing cloth with the chemical attack polish and submicron abrasive particles and buffing the metal surface.

  13. Attack polish for nickel-base alloys and stainless steels

    DOEpatents

    Not Available

    1980-05-28

    A chemical attack polish and polishing procedure for use on metal surfaces such as nickel base alloys and stainless steels is described. The chemical attack polich comprises FeNO/sub 3/, concentrated CH/sub 3/COOH, concentrated H/sub 2/SO/sub 4/ and H/sub 2/O. The polishing procedure includes saturating a polishing cloth with the chemical attack polish and submicron abrasive particles and buffing the metal surface.

  14. Reclamation and additional alloying of 18Ni(350) maraging steel

    SciTech Connect

    Ahmed, M.; Salam, I.; Nasim, I.; Hussain, S.W.; Hashmi, F.H.; Khan, A.Q. )

    1994-06-01

    The possibility of gainfully utilizing grade 18Ni(350) maraging steel scrap has been investigated, along with the effect of additional alloying with niobium. A vacuum induction melting and casting furnace was used for melting and additional alloying. The cast ingots were hot forged and their properties compared with those of the stock material. The composition of the reprocessed material was found to be within the prescribed range for 18Ni(350) steel, except for some loss in titanium content. The hardness and tensile strength of the recycled steels were similar to those of the stock material. A slight decrease in hardness in the aged condition could be attributed to loss of titanium during remelting. Charpy V-notch impact testing indicated significantly higher toughness in the remelted material; this has been attributed to a homogeneous, refined microstructure and a lower level of inclusions. Additional alloying with 2% Nb not only improved the mechanical properties but also affected the amount of reverted austenite obtained after aging.

  15. Creation of composite bronze - maraging steel alloy

    NASA Astrophysics Data System (ADS)

    Potekhin, B. A.; Ilyushin, V. V.; Khristolyubov, A. S.; Zhilyakov, A. Yu.; Ernandes, A.

    2013-09-01

    The possibility is demonstrated of creating alloys based on the system Cu - Fe - Ni - Al, within which the matrix is bronze BrNA 4-1, "reinforced" with dendrites containing, apart from Fe and Cu, about 15% Ni and 1% Al. This dendrite composition provides dispersion hardening. Favorable dendrite morphology provides high deformability of these bronzes, and makes it possible to control mechanical and service properties by heat treatment over a wide range.

  16. New alloys to conserve critical elements. [replacing chromium in steels

    NASA Technical Reports Server (NTRS)

    Stephens, J. R.

    1978-01-01

    Previous studies and surveys on availability of domestic reserves have shown that chromium is a most critical element within the U.S. metal industry. More precisely, the bulk of chromium is consumed in the production of stainless steels, specifically Type 304 stainless steel (304SS) which contains 18% Cr. The present paper deals with means of reducing chromium in commercial stainless steels by substituting more abundant or less expensive elements with the intent of maintaining the properties of 304SS. The discussion focuses on some of the oxidation and corrosion properties of new substitute stainless steels with only 12% Cr, which represents a potential saving of 33% of the chromium consumed in the production of 304SS. The alloying elements substituted for Cr in 304SS are selected according to their potential for protective oxide formation during high-temperature oxidation; these are Al, Si, Ti, Y, and misch metal which is 99.7% rare-earth metals containing 50 to 55% cerium. Other alloying elements to impart corrosion resistance are Mn, Mo, and V.

  17. Experimental and Theoretical Investigations of Hot Isostatically Pressed-Produced Stainless Steel/High Alloy Tool Steel Compound Materials

    NASA Astrophysics Data System (ADS)

    Lindwall, Greta; Flyg, Jesper; Frisk, Karin; Sandberg, Odd

    2011-05-01

    Consolidation of tool steel powders and simultaneous joining to a stainless 316L steel are performed by hot isostatic pressing (HIP). Two tool steel grades are considered: a high vanadium alloyed carbon tool steel, and a high vanadium and chromium alloyed nitrogen tool steel. The boundary layer arising during diffusion bonding is in focus and, in particular, the diffusion of carbon and nitrogen over the joint. Measurements of the elemental concentration profiles and corrosion tests by the double loop-electrochemical potentiokinetic reactivation (DL-EPR) method are performed. Comparative calculations with the DICTRA software are performed and are found to be in agreement with the experimental results. It is found that the carbon tool steel grade has a more critical influence on the corrosion resistance of the stainless 316L steel in comparison to the nitrogen tool steel grade.

  18. Mössbauer and XRD study of Al-Sn linished steel bimetal alloy

    NASA Astrophysics Data System (ADS)

    Kuzmann, E.; Silva, L. da; Stichleutner, S.; El-Sharif, M.; Homonnay, Z.; Klencsár, Z.; Sziráki, L.; Chisholm, C. U.; Lak, B.

    2016-12-01

    Aluminium alloy free CS1 type steel (0.06 wt% C, 0.45 wt% Mn) and samples of cold roll bonded steel bimetal alloys (MAS15 and MAS16) were fabricated and investigated by X-ray diffraction (XRD), 57Fe conversion electron Mössbauer spectroscopy (CEMS) at room temperature. XRD has revealed only the existence of the alpha iron solid solution (steel) phase in the steel only sample, while identified steel and metallic Al and Sn constituent phases in the bimetallic alloys. 57Fe Mössbauer spectroscopy revealed the presence of 4 % secondary iron-bearing phase attributed mainly to iron oxide/ oxyhydroxides (ferrihydrite) besides the steel matrix on the surface of the steel sample. A significant difference between the occurrences of the secondary phase of differently prepared bimetal alloys found in their 57Fe CEM spectra allowed to identify the main phase of debris as different iron oxide/ oxyhydroxides.

  19. Galvanic corrosion between dental precious alloys and magnetic stainless steels used for dental magnetic attachments.

    PubMed

    Takahashi, Noriko; Takada, Yukyo; Okuno, Osamu

    2008-03-01

    In this study, we examined the corrosion behavior of dental precious alloys and magnetic stainless steels, namely SUS 444, SUS XM27, and SUS 447J1, used for dental magnetic attachments. Their galvanic corrosion behavior was evaluated from the viewpoint of corrosion potentials when they were in contact with each other. Rest potentials of the precious alloys were constantly higher than those of magnetic stainless steels. Since most gold alloys raised the corrosion potential more significantly than silver alloys did, silver alloys seemed to be better suited than gold alloys for combination with magnetic stainless steels. However, all corrosion potential values were sufficiently lower than the breakdown potentials of the stainless steels and existed within their passive regions. Based on the findings of this study, SUS XM27 and SUS 447J1--which exhibited higher breakdown potentials than SUS 444--emerged as the preferred choices for combination with gold alloys.

  20. Bulk amorphous steels based on Fe alloys

    DOEpatents

    Lu, ZhaoPing; Liu, Chain T.

    2006-05-30

    A bulk amorphous alloy has the approximate composition: Fe.sub.(100-a-b-c-d-e)Y.sub.aMn.sub.bT.sub.cM.sub.dX.sub.e wherein: T includes at least one of the group consisting of: Ni, Cu, Cr and Co; M includes at least one of the group consisting of W, Mo, Nb, Ta, Al and Ti; X includes at least one of the group consisting of Co, Ni and Cr; a is an atomic percentage, and a<5; b is an atomic percentage, and b.ltoreq.25; c is an atomic percentage, and c.ltoreq.25; d is an atomic percentage, and d.ltoreq.25; and e is an atomic percentage, and 5.ltoreq.e.ltoreq.30.

  1. Effect of Stress Relief Annealing on Microstructure & Mechanical Properties of Welded Joints Between Low Alloy Carbon Steel and Stainless Steel

    NASA Astrophysics Data System (ADS)

    Nivas, R.; Das, G.; Das, S. K.; Mahato, B.; Kumar, S.; Sivaprasad, K.; Singh, P. K.; Ghosh, M.

    2017-01-01

    Two types of welded joints were prepared using low alloy carbon steel and austenitic stainless steel as base materials. In one variety, buttering material and weld metal were Inconel 82. In another type, buttering material and weld metal were Inconel 182. In case of Inconel 82, method of welding was GTAW. For Inconel 182, welding was done by SMAW technique. For one set of each joints after buttering, stress relief annealing was done at 923 K (650 °C) for 90 minutes before further joining with weld metal. Microstructural investigation and sub-size in situ tensile testing in scanning electron microscope were carried out for buttered-welded and buttered-stress relieved-welded specimens. Adjacent to fusion boundary, heat-affected zone of low alloy steel consisted of ferrite-pearlite phase combination. Immediately after fusion boundary in low alloy steel side, there was increase in matrix grain size. Same trend was observed in the region of austenitic stainless steel that was close to fusion boundary between weld metal-stainless steel. Close to interface between low alloy steel-buttering material, the region contained martensite, Type-I boundary and Type-II boundary. Peak hardness was obtained close to fusion boundary between low alloy steel and buttering material. In this respect, a minimum hardness was observed within buttering material. The peak hardness was shifted toward buttering material after stress relief annealing. During tensile testing no deformation occurred within low alloy steel and failure was completely through buttering material. Crack initiated near fusion boundary between low alloy steel-buttering material for welded specimens and the same shifted away from fusion boundary for stress relieved annealed specimens. This observation was at par with the characteristics of microhardness profile. In as welded condition, joints fabricated with Inconel 82 exhibited superior bond strength than the weld produced with Inconel 182. Stress relief annealing

  2. Mechanical alloying of lanthana-bearing nanostructured ferritic steels

    SciTech Connect

    Somayeh Paseban; Indrajit Charit; Yaqiao Q. Wu; Jatuporn Burns; Kerry N. Allahar; Darryl P. Butt; James I. Cole

    2013-09-01

    A novel nanostructured ferritic steel powder with the nominal composition Fe–14Cr–1Ti–0.3Mo–0.5La2O3 (wt.%) was developed via high energy ball milling. La2O3 was added to this alloy instead of the traditionally used Y2O3. The effects of varying the ball milling parameters, such as milling time, steel ball size and ball to powder ratio, on the mechanical properties and micro structural characteristics of the as-milled powder were investigated. Nanocrystallites of a body-centered cubic ferritic solid solution matrix with a mean size of approximately 20 nm were observed by transmission electron microscopy. Nanoscale characterization of the as-milled powder by local electrode atom probe tomography revealed the formation of Cr–Ti–La–O-enriched nanoclusters during mechanical alloying. The Cr:Ti:La:O ratio is considered “non-stoichiometric”. The average size (radius) of the nanoclusters was about 1 nm, with number density of 3.7 1024 m3. The mechanism for formation of nanoclusters in the as-milled powder is discussed. La2O3 appears to be a promising alternative rare earth oxide for future nanostructured ferritic steels.

  3. 78 FR 2658 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Rescission of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-14

    ... International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Rescission of... its administrative review of the antidumping duty order on carbon and certain alloy steel wire rod (``wire rod'') from Mexico for the period October 1, 2011, through September 30, 2012. DATES:...

  4. 75 FR 69125 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-10

    ... COMMISSION Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From China Determination... alloy steel standard, line, and pressure pipe (``seamless SLP pipe''), provided for in subheadings 7304..., and Pressure Pipe from China: Investigation Nos. 701-TA-469 and 731-TA-1168 (Final). \\4\\ On...

  5. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  6. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  7. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  8. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  9. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  10. Copper modified austenitic stainless steel alloys with improved high temperature creep resistance

    DOEpatents

    Swindeman, R.W.; Maziasz, P.J.

    1987-04-28

    An improved austenitic stainless steel that incorporates copper into a base Fe-Ni-Cr alloy having minor alloying substituents of Mo, Mn, Si, T, Nb, V, C, N, P, B which exhibits significant improvement in high temperature creep resistance over previous steels. 3 figs.

  11. 78 FR 60316 - Carbon and Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico, Moldova, Trinidad and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-01

    ... Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico, Moldova, Trinidad and Tobago, and Ukraine... determine whether revocation of the countervailing duty order on carbon and certain alloy steel wire rod from Brazil and antidumping duty orders on carbon and certain alloy steel wire rod from...

  12. 77 FR 66954 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Preliminary Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-08

    ... International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Preliminary Results of... on carbon and certain alloy steel wire rod (wire rod) from Mexico. The period of review is October 1... certain alloy steel wire rod. The product is currently classified under the Harmonized Tariff Schedule...

  13. 75 FR 69050 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-10

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe... duty order on certain seamless carbon and alloy steel standard, line, and pressure pipe (``seamless... seamless pipe from the PRC. See Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure...

  14. 75 FR 29972 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-28

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe... antidumping duty investigation of certain seamless carbon and alloy steel standard, line, and pressure pipe... in this proceeding. See Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure...

  15. 77 FR 21968 - Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-12

    ... International Trade Administration Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the... and alloy steel standard, line, and pressure pipe from the People's Republic of China. The period of... countervailing duty order on seamless carbon and alloy steel standard, line, and pressure pipe from the...

  16. 75 FR 57444 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-21

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe... alloy steel standard, line, and pressure pipe (``seamless pipe'') from the People's Republic of China... determination. See Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the...

  17. 46 CFR 54.25-15 - Low temperature operation-high alloy steels (modifies UHA-23(b) and UHA-51).

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Low temperature operation-high alloy steels (modifies... (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Construction With Carbon, Alloy, and Heat Treated Steels § 54.25-15 Low temperature operation—high alloy steels (modifies UHA-23(b) and UHA-51). (a)...

  18. 46 CFR 54.25-15 - Low temperature operation-high alloy steels (modifies UHA-23(b) and UHA-51).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Low temperature operation-high alloy steels (modifies... (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Construction With Carbon, Alloy, and Heat Treated Steels § 54.25-15 Low temperature operation—high alloy steels (modifies UHA-23(b) and UHA-51). (a)...

  19. 46 CFR 54.25-15 - Low temperature operation-high alloy steels (modifies UHA-23(b) and UHA-51).

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Low temperature operation-high alloy steels (modifies... (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Construction With Carbon, Alloy, and Heat Treated Steels § 54.25-15 Low temperature operation—high alloy steels (modifies UHA-23(b) and UHA-51). (a)...

  20. 46 CFR 54.25-15 - Low temperature operation-high alloy steels (modifies UHA-23(b) and UHA-51).

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Low temperature operation-high alloy steels (modifies... (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Construction With Carbon, Alloy, and Heat Treated Steels § 54.25-15 Low temperature operation—high alloy steels (modifies UHA-23(b) and UHA-51). (a)...

  1. 46 CFR 54.25-15 - Low temperature operation-high alloy steels (modifies UHA-23(b) and UHA-51).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Low temperature operation-high alloy steels (modifies... (CONTINUED) MARINE ENGINEERING PRESSURE VESSELS Construction With Carbon, Alloy, and Heat Treated Steels § 54.25-15 Low temperature operation—high alloy steels (modifies UHA-23(b) and UHA-51). (a)...

  2. 76 FR 15941 - Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Extension of the Final Results...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-22

    ... International Trade Administration Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Extension of... antidumping duty administrative review of circular welded non-alloy steel pipe from the Republic of Korea, covering the period November 1, 2008, through October 31, 2009. See Circular Welded Non-Alloy Steel...

  3. 77 FR 8808 - Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Extension of the Final Results...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-15

    ... International Trade Administration Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Extension of... antidumping duty administrative review of circular welded non-alloy steel pipe from the Republic of Korea, covering the period November 1, 2009, through October 31, 2010. See Circular Welded Non-Alloy Steel...

  4. 77 FR 73015 - Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Preliminary Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-07

    ... International Trade Administration Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Preliminary... conducting an administrative review of the antidumping duty order on circular welded non-alloy steel pipe... merchandise subject to the order is circular welded non-alloy steel pipe and tube. The product is...

  5. 76 FR 14649 - Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Extension of Time Limit for Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-17

    ... International Trade Administration Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Extension of Time... circular welded non-alloy steel pipe from Mexico for the November 1, 2008, through October 31, 2009, period of review. See Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Preliminary Results...

  6. 75 FR 20342 - Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-19

    ... International Trade Administration Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Final Results of... antidumping duty order on certain circular welded non- alloy steel pipe from Mexico. See Certain Circular Welded Non-Alloy Steel Pipe From Mexico; Preliminary Results of Antidumping Duty Administrative...

  7. 76 FR 44304 - Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Amended Final Results of the...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-25

    ... International Trade Administration Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Amended..., 2009. See Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Final Results of the... during the period of review. See Circular Welded Non-Alloy Steel Pipe From the Republic of...

  8. Precipitation sequence in niobium-alloyed ferritic stainless steel

    NASA Astrophysics Data System (ADS)

    Fujita, Nobuhiro; Bhadeshia, H. K. D. H.; Kikuchi, Masao

    2004-03-01

    Niobium is an important alloying element in the design of heat-resistant ferritic stainless steels for automotive exhaust systems. When in solid solution, it improves both the high temperature strength and the resistance to thermal fatigue. However, it also forms several kinds of precipitates during service. These reactions have been modelled, taking into account the multicomponent nature of the diffusion process and allowing for capillarity effects. It has been possible to estimate not only the volume fractions but also the particle sizes for Fe2Nb (Laves phase) and Fe3Nb3C (M6C) carbide in a 19Cr-0.8Nb steel, with good agreement against experimental data.

  9. Crack initiation mechanisms in IASCC of stainless steel alloys

    SciTech Connect

    Cookson, J.M.; Was, G.S.; Andresen, P.L.

    1995-12-31

    An abnormally high oxygen concentration was recently discovered in a high purity stainless steel alloy widely used in IASCC studies. This led to an investigation into the role of oxygen on the initiation of intergranular cracking in irradiated samples in high temperature water. The concentration of oxygen in the alloys correlated with the number of cracks initiated in the proton irradiated region of samples strained in water containing 0.5 {micro}S/cm H{sub 2}SO{sub 4} at 288 C. This suggests that the presence of oxygen, in the form of spinel oxide particles, can lead to a substantial increase in the likelihood of crack initiation. This effect is only observed in irradiated samples strained in water, not in either unirradiated (non-sensitized) samples strained in water or irradiated samples strained in argon This paper examines the possible role of oxides in promoting crack initiation and the implications for IASCC.

  10. Alternative to Nitric Acid for Passivation of Stainless Steel Alloys

    NASA Technical Reports Server (NTRS)

    Lewis, Pattie L.; Kolody, Mark; Curran, Jerry

    2013-01-01

    Corrosion is an extensive problem that affects the Department of Defense (DoD) and National Aeronautics and Space Administration (NASA). The deleterious effects of corrosion result in steep costs, asset downtime affecting mission readiness, and safety risks to personnel. Consequently, it is vital to reduce corrosion costs and risks in a sustainable manner. The DoD and NASA have numerous structures and equipment that are fabricated from stainless steel. The standard practice for protection of stainless steel is a process called passivation. Typical passivation procedures call for the use of nitric acid; however, there are a number of environmental, worker safety, and operational issues associated with its use. Citric acid offers a variety of benefits including increased safety for personnel, reduced environmental impact, and reduced operational cost. DoD and NASA agreed to collaborate to validate citric acid as an acceptable passivating agent for stainless steel. This paper details our investigation of prior work developing the citric acid passivation process, development of the test plan, optimization of the process for specific stainless steel alloys, ongoing and planned testing to elucidate the process' resistance to corrosion in comparison to nitric acid, and preliminary results.

  11. Anticorrosion nitrided layers on unalloyed and alloyed steels

    NASA Astrophysics Data System (ADS)

    Wach, P.; Michalski, J.; Burdyński, K.; Ciski, A.

    2017-02-01

    In the paper, nitrided layers on unalloyed and alloyed steels and their corrosion properties are presented. Nitrided layers in the controlled gas nitriding process on C10 and 42CrMo4 steels were formed. Two types of nitrided layers are presented: with nitride iron layers above and below 15 µm. Nitrided layer with nitride layer above 15 µm has good corrosion resistance, but after nitriding of machine parts were subsequently oxidised and impregnated. In the second type of nitrided layer, the surface layers of iron nitrides had a thickness of 3.0 to 11.0 µm. Nitrided layers with a surface layer of iron nitrides with the γ’ (Fe4N) structure were formed on unalloyed steel and investigated. The so-formed layers were subject to basic metallographic, X-ray diffraction and corrosion resistance studies carried out by electrochemical methods and in a neutral salt spray chamber. It was found that the layers consisting only of γ’ phase had a good corrosion resistance. Necessary requirements for achieving an enhanced resistance comprise their complete tightness and thickness not lower than 9.0 µm. Thinner layers had good electrochemical properties but did not exhibit corrosion resistance in the salt spray chamber.

  12. Reactive Boride Brazing on Low-Alloy Automotive Grade Steel

    NASA Astrophysics Data System (ADS)

    Palanisamy, B.; Upadhyaya, A.

    2011-11-01

    Brazing is a widely used process to improve the performance of steels used in automotive applications. The substrate material is often exposed to harsh conditions in these applications and may affect the service life of the component. Reactive boride brazing aims to improve the mechanical properties of the substrate material by forming a ceramic-metal composite coating in a single-step process in situ. In this study, sintered Ancor 4300 low-alloy steel is used as the substrate with chromium-rich braze and chromium-lean braze materials. The mechanical properties of the brazed samples were studied in detail using microindentation hardness measurements and the transverse rupture test. The results indicate that the brazed superlayer has a 10 times higher hardness. There was a significant improvement in the transverse rupture strength of the steel brazed with the chromium-rich boride as compared to the pure substrate material. In an effort to reduce processing time, green compacts of the substrate were also directly brazed and yielded favorable results.

  13. Laser beam surface melting of high alloy austenitic stainless steel

    SciTech Connect

    Woollin, P.

    1996-12-31

    The welding of high alloy austenitic stainless steels is generally accompanied by a substantial reduction in pitting corrosion resistance relative to the parent, due to microsegregation of Mo and Cr. This prevents the exploitation of the full potential of these steels. Processing to achieve remelting and rapid solidification offers a means of reducing microsegregation levels and improving corrosion resistance. Surface melting of parent UNS S31254 steel by laser beam has been demonstrated as a successful means of producing fine, as-solidified structures with pitting resistance similar to that of the parent, provided that an appropriate minimum beam travel speed is exceeded. The use of N{sub 2} laser trail gas increased the pitting resistance of the surface melted layer. Application of the technique to gas tungsten arc (GTA) melt runs has shown the ability to raise the pitting resistance significantly. Indeed, the use of optimized beam conditions, N{sub 2} trail gas and appropriate surface preparation prior to laser treatment increased the pitting resistance of GTA melt runs to a level approaching that of the parent material.

  14. RKF-PCA: robust kernel fuzzy PCA.

    PubMed

    Heo, Gyeongyong; Gader, Paul; Frigui, Hichem

    2009-01-01

    Principal component analysis (PCA) is a mathematical method that reduces the dimensionality of the data while retaining most of the variation in the data. Although PCA has been applied in many areas successfully, it suffers from sensitivity to noise and is limited to linear principal components. The noise sensitivity problem comes from the least-squares measure used in PCA and the limitation to linear components originates from the fact that PCA uses an affine transform defined by eigenvectors of the covariance matrix and the mean of the data. In this paper, a robust kernel PCA method that extends the kernel PCA and uses fuzzy memberships is introduced to tackle the two problems simultaneously. We first introduce an iterative method to find robust principal components, called Robust Fuzzy PCA (RF-PCA), which has a connection with robust statistics and entropy regularization. The RF-PCA method is then extended to a non-linear one, Robust Kernel Fuzzy PCA (RKF-PCA), using kernels. The modified kernel used in the RKF-PCA satisfies the Mercer's condition, which means that the derivation of the K-PCA is also valid for the RKF-PCA. Formal analyses and experimental results suggest that the RKF-PCA is an efficient non-linear dimension reduction method and is more noise-robust than the original kernel PCA.

  15. Cathodic protection of steel by electrodeposited zinc-nickel alloy coatings

    SciTech Connect

    Baldwin, K.R.; Smith, C.J.E.; Robinson, M.J.

    1995-12-01

    The ability of electrodeposited zinc-nickel alloy coatings to cathodically protect steel was studied in dilute chloride solutions. The potential distribution along steel strips partly electroplated with zinc-nickel alloys was determined, and the length of exposed steel that was held below the minimum protection potential (E{sub prot}) was taken as a measure of the level of cathodic protection (CP) provided by the alloy coatings. The level of CP afforded by zinc alloy coatings was found to decrease with increasing nickel content. When nickel content was increased to {approx} {ge} 21 wt%, no CP was obtained. Surface analysis of uncoupled zinc-nickel alloys that were immersed in sodium chloride (NaCl) solutions showed the concentration of zinc decreased in the surface layers while the concentration of nickel increased, indicating that the alloys were susceptible to dezincification. The analysis of zinc-nickel alloy coatings on partly electroplated steel strips that were immersed in chloride solution showed a significantly higher level of dezincification than that found for uncoupled alloy coatings. This effect accounted for the rapid loss of CP afforded to steel by some zinc alloy coatings, particularly those with high initial nickel levels.

  16. Friction Stir Welding of Age-Hardenable Aluminum Alloys: A Parametric Approach Using RSM Based GRA Coupled With PCA

    NASA Astrophysics Data System (ADS)

    Vijayan, D.; Rao, V. S.

    2014-04-01

    Age-hardenable aluminum alloys, primarily used in the aerospace, automobile and marine industries (2×××, 6××× and 7×××), can be welded using solid-state welding techniques. Friction stir welding is an emerging solid-state welding technique used to join both similar and dissimilar materials. The strength of a friction stir welded joint depends on the joining process parameters. Therefore, a combination of the statistical techniques of a response surface methodology based on a grey relational analysis coupled to a principal component analysis was proposed to select the process parameters suitable for joining AA 2024 and AA 6061 aluminum alloys via friction stir welding. The significant process parameters, such as rotational speed, welding speed, axial load and pin shapes (PS) were considered during the statistical experiment. The results indicate that the square PS plays a vital role and yields an ultimate tensile strength of 141 MPa for an elongation of 12 % versus cylinder and taper pin profiles. The root cause for joint strength loss and fracture mode was analyzed using scanning electron microscopy. Severe material flow during macro defects, such as pin holes and porosity, degrades the joint strength by approximately 44 % for AA 2024 and 51 % for AA 6061 fabricated FS-welded aluminum alloys relative to the base material. The results of this approach are useful for accurately controlling the response and optimize the process parameters.

  17. Deformation and fracture of low alloy steels at high temperature

    SciTech Connect

    Marriott, D.L.; Stubbins, J.F.; Leckie, F.A.; Muddle, B.

    1988-12-01

    This project formed part of the initiative in the AR TD program to characterize high temperature, time-dependent damage processes in low alloy steels, for use in the construction of coal-gasification plant. This project was broadly aimed at adding to the knowledge base for this bainitic form of 2.25Cr 1Mo steel, as it related to time-dependent performance at elevated temperature. Its original intention was to obtain information in specific grades of 2.25Cr 1Mo steel, in particular those containing reduced residual elements and microalloyed modifications, which were being considered as candidate materials at the time. This objective was subsequently modified, in the course of the contract period, to a more generic study of bainitic steel, using the 2.25Cr 1Mo material as a representative of the class. The main thrust of the project was directed initially at the detrimental effect of cyclic loading on creep resistance and manifesting itself in an apparently severe creep-fatigue interaction. Three subtasks were eventually identified. These are: a study of the evolution of microstructural changes in bainitic materials during steady load creep and under constant amplitude cyclic deformation, investigation of the effect of cyclic softening on the fatigue and creep strength of complex geometries, focusing on circumferentially notched bars, and investigation of the influence of environment as a possible cause of observed fatigue/elevated temperature interaction through its effects on crack initiation and propagation, using EDM notched specimens tested in air and vacuum. Results are discussed. 24 refs., 40 figs., 5 tabs.

  18. Enhancement of Impact Toughness by Delamination Fracture in a Low-Alloy High-Strength Steel with Al Alloying

    NASA Astrophysics Data System (ADS)

    Sun, Junjie; Jiang, Tao; Liu, Hongji; Guo, Shengwu; Liu, Yongning

    2016-12-01

    The effect of delamination toughening of martensitic steel was investigated both at room and low temperatures [253 K and 233 K (-20 °C and -40 °C)]. Two low-alloy martensitic steels with and without Al alloying were both prepared. Layered structure with white band and black matrix was observed in Al alloyed steel, while a homogeneous microstructure was displayed in the steel without Al. Both steels achieved high strength (tensile strength over 1600 MPa) and good ductility (elongation over 11 pct), but they displayed stark contrasts on impact fracture mode and Charpy impact energy. Delamination fracture occurred in Al alloyed steel and the impact energies were significantly increased both at room temperature (from 75 to 138 J, i.e., nearly improved up to 2 times) and low temperatures [from 47.9 to 71.3 J at 233 K (-40 °C)] compared with the one without Al. Alloying with Al promotes the segregation of Cr, Mn, Si and C elements to form a network structure, which is martensite with higher carbon content and higher hardness than that of the matrix. And this network structure evolved into a band structure during the hot rolling process. The difference of yield stress between the band structure and the matrix gives rise to a delamination fracture during the impact test, which increases the toughness greatly.

  19. Reaction of Unalloyed and Cr-Mo Alloyed Steels with Nitrogen from the Sintering Atmosphere

    NASA Astrophysics Data System (ADS)

    Dlapka, Magdalena; Gierl-Mayer, Christian; Calderon, Raquel de Oro; Danninger, Herbert; Bengtsson, Sven; Dudrova, Eva

    2016-12-01

    Nitrogen is usually regarded as an inert sintering atmosphere for PM steels; however, this cannot be taken for granted in particular for steels alloyed with nitride forming elements. Among those elements, chromium has become more and more important as an alloying element in sintered low alloy structural steels in the last decade due to the moderate alloying cost and the excellent mechanical properties obtainable, in particular when sinter hardening is applied. The high affinity of Cr to oxygen and the possible ways to overcome related problems have been the subject of numerous studies, while the fact that chromium is also a fairly strong nitride forming element has largely been neglected at least for low alloy steel grades, although frequently used materials like steels from Cr and Cr-Mo prealloyed powders are commonly sintered in atmospheres consisting mainly of nitrogen. In the present study, nitrogen pickup during sintering at different temperatures and for varying times has been studied for Cr-Mo prealloyed steel grades as well as for unalloyed carbon steel. Also the effect of the cooling rate and its influence on the properties, of the microstructure and the composition have been investigated. It showed that the main nitrogen uptake occurs not during isothermal sintering but rather during cooling. It could be demonstrated that a critical temperature range exists within which the investigated CrM-based steel is particularly sensitive to nitrogen pickup.

  20. Microscopic study of the structure of the Steel Ni-based Alloy: Hastelloy G35 Alloy

    NASA Astrophysics Data System (ADS)

    Sabir, F.; Ben Lenda, O.; Saissi, S.; Marbouh, K.; Tyouke, B.; Zerrouk, L.; Ibnlfassi, A.; Ouzaouit, K.; Elmadani, S.

    2017-03-01

    The study of the influence of heat treatment on changes of mechanical and structural properties of Steel Ni-based Alloy is a highly interdisciplinary topic at the interface of the physical chemistry of metallic materials, which also helps in environmental and economic protection.After heat treatment, the structural and micro-structural studies for the different transformation temperature led to identify phases formed and the morphology. This work has been carried out using different techniques: X-ray diffraction, optical microscopy and scanning electron microscopy.

  1. The Evolution of the Segregation Behavior of Alloying Elements in a Low-Alloy Steel

    SciTech Connect

    A.J. Papworth; D.B. Knorr; D.B. Williams

    2002-08-21

    The segregation of alloying and impurity elements to prior austenite grain boundaries (PAGBs) in low-alloy steels controls temper-embrittlement although the precise microchemical and microstructural interactions are, as yet, unclear because of the many variables involved. Competing segregation and de-segregation phenomena are observed. For example, Auger analyses of fracture surfaces indicate that brittle fracture is caused by the segregation of P to the PAGB. The addition of small amounts ({approx} 0.5 wt%) of Mo appears to regard, but not stop, temper-embrittlement, possibly due to Mo{sub 2}C precipitates that form at elevated temperatures causing de-segregation of Mo from the PAGB. The relationship between segregation and temper embrittlement is further complicated in commercial alloys by both the number of segregating elements and the complex, multi-stage heat treatments. Auger analysis pre-selects the most embrittled boundaries and so the complete distribution of segregants across all PAGBs cannot be determined by this technique. Previous work has shown how X-ray mapping (XRM) in a field-emission gun scanning transmission electron microscope (FEG-STEM) offers a more complete view of the distribution of segregants on both non-embrittled and embrittled PAGBs. XRM was used to observe the evolution of the segregation and desegregation of five elements during four successive heat-treatment stages of commercial low-alloy steel forging. In the last and crucial temper-embrittlement stage, increases in the degree and frequency of Ni segregation occur while other elements either segregate, remain constant or desegregate from the PAGBs.

  2. Corrosion Behavior and Durability of Low-Alloy Steel Rebars in Marine Environment

    NASA Astrophysics Data System (ADS)

    Liu, Ming; Cheng, Xuequn; Li, Xiaogang; Yue, Pan; Li, Jun

    2016-11-01

    The corrosion resistance of Cr-modified low-alloy steels and HRB400 carbon steel was estimated using the open-circuit potential, potentiodynamic polarization, electrochemical impedance spectroscopic, and weight loss methods in simulated concrete pore solution. Results show that Cr-modified steels exhibit a higher corrosion resistance with a higher critical chloride level (CTL), lower corrosion current density, and higher impedance than carbon steel. The CTL of the steels significantly reduces with increasing temperature. Weight loss measurement shows that the Cr-modified steels exhibit low corrosion rates and small corrosion pitting. The primary constituents of the corrosion scales are Fe2O3, Fe3O4, β-FeOOH, γ-FeOOH, and α-FeOOH. A large amount of α-FeOOH could be detected in the Cr-modified steel corrosion products. Moreover, the Cr-modified steels demonstrate a higher durability than HRB400 carbon steel.

  3. 77 FR 43806 - Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-26

    ... International Trade Administration Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the... steel standard, line, and pressure pipe from the People's Republic of China. The period of review is... carbon and alloy steel standard, line, and pressure pipe from the People's Republic of China covering...

  4. Iodine sorption on low-chromium alloy steel. [HTGR

    SciTech Connect

    Osborne, M.F.; Briggs, R.B.; Wichner, R.P.

    1982-01-01

    Studies of iodine sorption on low-alloy steel in helium atmosphere included both computer calculations and experimental measurements under conditions that could be related to the high-temperature gas-cooled reactor (HTGR). Adsorption measurements provide data on the potentially releasable inventory of iodine (a major radiological hazard) stored on surfaces in the coolant circuit during normal operation. Measurements of the rate and extent of iodine desorption when test conditions were changed are useful for evaluating the consequences of accidents. The results of calculations with the SOLGASMIX-PV computer program indicated that HI is the dominant iodine species in the system and that the deposition of CrI/sub 2/(s) or FeI/sub 2/(s) in the cooler regions will effectively limit the amount of iodine in the gas phase. Experimental measurements were obtained on 2-1/4% Cr-1% Mo steel specimens at iodine burdens as low as 10/sup -6/ Pa (10/sup -11/ atm), about 100 times lower than any previous work.

  5. Boric acid corrosion of carbon and low alloy steels

    SciTech Connect

    Campbell, C.A.; Fyfitch, S.; Martin, D.T.

    1994-12-31

    Leakage of borated water from the reactor coolant system of pressurized water reactors (PWRs) and the resulting corrosion of carbon and low alloy steel components are concerns that have been addressed by utilities for many years. Significant corrosion has been observed in instances where such leakage has gone undetected for several months. In 1990, the B and W Owners Group (B and WOG) sponsored a test program to determine the levels of wastage that are possible when primary water leakage occurs. In this test program, carbon and stainless steel specimens were exposed to borated water at temperatures from 300 F to 550 F. Initial boric acid concentration was controlled within the limits of 13,000 to 15,000 ppm (as H{sub 3}BO{sub 3}) with 1.0--2.0 ppm lithium (as LiOH) added to duplicate the primary water chemistry. Testing was performed to determine the degree of attack caused by a leak traveling along a pipe both with and without insulation. These tests show the importance of temperature and boric acid concentrations on the wastage that can occur from such a leak.

  6. Nanosized controlled surface pretreatment of biometallic alloy 316L stainless steel.

    PubMed

    Abdel-Fattah, Tarek M; Loftis, Derek; Mahapatro, Anil

    2011-12-01

    Stainless steel (AISI 316L) is a medical grade stainless steel alloy used extensively in medical devices and in the biomedical field. 316L stainless steel was successfully electropolished via an ecologically friendly and biocompatible ionic liquid (IL) medium based on Vitamin B4 (NB4) and resulting in nanosized surface roughness and topography. Voltammetry and chronoamperometry tests determined optimum polishing conditions for the stainless steel alloy while atomic force microscopy (AFM) and scanning electron microscopy (SEM) provided surface morphology comparisons to benchmark success of each electropolishing condition. Energy dispersive X-ray analysis (EDX) combined with SEM revealed significantly smoother surfaces for each alloy surface while indicating that the constituent metals comprising each alloy effectively electropolished at uniform rates.

  7. Al-Li alloys and ultrahigh-strength steels for U. S. Navy aircraft

    SciTech Connect

    Lee, E.W.; Neu, C.E.; Kozol, J. )

    1990-05-01

    An evaluation is made of the development status and prospective performance advantages and cost reductions obtainable through the application of state-of-the-art Al-Li alloys to naval aircraft airframes and ultrahigh strength Ni-Co alloy steels to their landing gears. Structural weight fractions are expected to be reduced by 8-10 percent through substitution of high-stiffness Al-Li for conventional Al alloys. Ni-Co alloy steels enhance landing gear damage tolerance and resistance to environmental degradation, without associated weight penalty, when supplanting conventional low-alloy steels. Both materials are judged ready for immediate application to existing and next-generation U.S. Navy aircraft. 8 refs.

  8. Industrial Experience on the Caustic Cracking of Stainless Steels and Nickel Alloys - A Review

    SciTech Connect

    Rebak, R B

    2005-10-09

    Caustic environments are present in several industries, from nuclear power generation to the fabrication of alkalis and alumina. The most common material of construction is carbon steel but its application is limited to a maximum temperature of approximately 80 C. The use of Nickel (Ni) alloys is recommended at higher temperatures. Commercially pure Ni is the most resistant material for caustic applications both from the general corrosion and the stress corrosion cracking (SCC) perspectives. Nickel rich alloys also offer a good performance. The most important alloying elements are Ni and chromium (Cr). Molybdenum (Mo) is not a beneficial alloying element and it dissolves preferentially from the alloy in presence of caustic environments. Austenitic stainless steels such as type 304 and 316 seem less resistant to caustic conditions than even plain carbon steel. Experimental evidence shows that the most likely mechanism for SCC is anodic dissolution.

  9. Raising the Structural Strength of Systematically Alloyed Fe - Cr - Ni - Mo-Base Maraging Steels

    NASA Astrophysics Data System (ADS)

    Gladkovskii, S. V.; Ishina, E. A.; Kuteneva, S. V.

    2016-03-01

    The effect of systematical Mo, Ti, Al and Ca alloying of corrosion-resistant maraging steels of type Kh11N10M2T and of the modes of their heat treatment on the phase composition, combination of properties and resistance to brittle fracture is studied. It is shown that the structural strength of the steels can be raised by additional alloying with copper and formation of a regulated content of metastable retained austenite.

  10. Comparison of Channel Segregation Formation in Model Alloys and Steels via Numerical Simulations

    NASA Astrophysics Data System (ADS)

    Cao, Y. F.; Chen, Y.; Li, D. Z.; Liu, H. W.; Fu, P. X.

    2016-06-01

    In the current study, the evolutions of channel segregations in several alloy systems, such as the typically used model alloys ( e.g., Ga-In, Sn-Pb, Sn-Bi, Al-Cu, and Ni-based superalloy) and some special steels, are numerically simulated in a cavity solidified unidirectionally. The simulations are based on a modified continuum macrosegregation model with an extension to the multicomponent systems. The results of model alloys and steels indicate that when the thermosolutal convection is strong enough, flow instability occurs, which in turn destabilizes the mushy zone. Subsequently, the channel segregation forms with the continuous interaction between solidification and flow. The formation behavior and severity of channel segregations in various systems are different owing to their distinct melt convection strengths and solidification natures. In the current simulations, channels are apparent for model alloys with high content of solutes, whereas they are slight in some special steels, such as 27SiMn steel, and totally disappear in carbon steels. These occurrence features of channel segregation in simulations of steels are consistent with the analyses by a modified Rayleigh number associated with alloying elements, and both outcomes are well supported by the fully sectioned steel ingots in experiments.

  11. Three-dimensional atom probe characterization of alloy element partitioning in cementite during tempering of alloy steel.

    PubMed

    Zhu, Chen; Xiong, X Y; Cerezo, A; Hardwicke, R; Krauss, G; Smith, G D W

    2007-09-01

    Hardness measurements confirm that the martensitic microstructure of an alloy steel, AISI/SAE 4340, is significantly more resistant to softening, compared to the martensitic microstructure of a high-purity Fe-0.4% C alloy, at tempering temperatures, 300-400 degrees C, just above the temperatures where cementite replaces transition carbides in the martensitic matrix. Three-dimensional atom probe (3DAP) analyses of the 4340 steel show that Si rejection from the cementite is first detected after low-temperature tempering for times of 1 h. After 10-h tempering at 400 degrees C, Mn and Cr contents are increased, and Ni contents decreased, in cementite according to their carbide- and non-carbide-forming tendencies, respectively. The results are discussed with respect to the diffusivity of the substitutional alloying elements in the 4340 steel, and the effect that such diffusion-controlled redistribution would have on maintaining fine distributions of cementite that resist softening during tempering.

  12. Stablization of Nanotwinned Microstructures in Stainless Steels Through Alloying and Microstructural Design

    DTIC Science & Technology

    2013-08-23

    stable nanotwinned microstructure---high-temperature strength. The long - term goal of this effort is to develop austenitic stainless steels capable of...microstructures. The long - term alloy design strategy focuses on microalloying additions to 1) reduce the stacking fault energy (SFE), enhance twinning formation...15. SUBJECT TERMS materials design, stainless steels , plastic deformation by twinning, computational materials science, experimental characterization

  13. Use of Nitrocarburizing for Strengthening Threaded Joints of Drill Pipes from Medium-Carbon Alloy Steels

    NASA Astrophysics Data System (ADS)

    Priymak, E. Yu.; Stepanchukova, A. V.; Yakovleva, I. L.; Tereshchenko, N. A.

    2015-05-01

    Nitrocarburizing is tested at the Drill Equipment Plant for reinforcing threaded joints of drill pipes for units with retrievable core receiver (RCR). The effect of the nitrocarburizing on the mechanical properties of steels of different alloying systems is considered. Steels for the production of threaded joints of drill pipes are recommended.

  14. Friction Stir Lap Welding of Magnesium Alloy to Steel: A Preliminary Investigation

    SciTech Connect

    Jana, Saumyadeep; Hovanski, Yuri; Grant, Glenn J.

    2010-12-01

    An initial study was made to evaluate the feasibility of joining Magnesium alloy AZ31 sheet to galvanized steel sheet in lap configuration using friction stir welding (FSW). Two different automotive sheet steels were used for comparative evaluation of the dissimilar joining potential; a 0.8mm thick, electro galvanized (EG) mild steel, and a 1.5mm thick hot dipped galvanized (HDG) high-strength, low-alloy steel (HSLA). These steels were joined to 2.33mm thick AZ31B magnesium sheet. A single FSW tool design was used for both dissimilar welds, and process parameters were kept the same. Average peak load for the AZ31-1.5 mm steel weld joint in lap shear mode was found to be 6.3 ± 1.0 kN. For the AZ31-0.8 mm steel weld, joint strength was 5.1 ± 1.5 kN. Microstructural investigation indicates melting of the Zn coating at the interface and subsequent alloying with the Mg sheet resulting in formation of solidified Zn-Mg alloy layer at AZ31/steel interface.

  15. Etching process mills PH 14-8 Mo alloy steel to precise tolerances

    NASA Technical Reports Server (NTRS)

    Chipman, B. L.; Mulland, P. W.

    1966-01-01

    Chemical milling process, which combines an aqua regia etchant with a sulfonate wetting agent, produces finishes on PH 14-8 molybdenum alloy steel to precise tolerances. This process permits precision removal of excess metal from the steel in annealed and/or aged conditions.

  16. M551 metals melting experiment. [space manufacturing of aluminum alloys, tantalum alloys, stainless steels

    NASA Technical Reports Server (NTRS)

    Li, C. H.; Busch, G.; Creter, C.

    1976-01-01

    The Metals Melting Skylab Experiment consisted of selectively melting, in sequence, three rotating discs made of aluminum alloy, stainless steel, and tantalum alloy. For comparison, three other discs of the same three materials were similarly melted or welded on the ground. The power source of the melting was an electron beam unit. Results are presented which support the concept that the major difference between ground base and Skylab samples (i.e., large elongated grains in ground base samples versus nearly equiaxed and equal sized grains in Skylab samples) can be explained on the basis of constitutional supercooling, and not on the basis of surface phenomena. Microstructural observations on the weld samples and present explanations for some of these observations are examined. In particular, ripples and their implications to weld solidification were studied. Evidence of pronounced copper segregation in the Skylab A1 weld samples, and the tantalum samples studied, indicates a weld microhardness (and hence strength) that is uniformly higher than the ground base results, which is in agreement with previous predictions. Photographs are shown of the microstructure of the various alloys.

  17. Steam Oxidation Behavior of Advanced Steels and Ni-Based Alloys at 800 °C

    NASA Astrophysics Data System (ADS)

    Dudziak, T.; Boroń, L.; Deodeshmukh, V.; Sobczak, J.; Sobczak, N.; Witkowska, M.; Ratuszek, W.; Chruściel, K.

    2017-02-01

    This publication studies the steam oxidation behavior of advanced steels (309S, 310S and HR3C) and Ni-based alloys (Haynes® 230®, alloy 263, alloy 617 and Haynes® 282®) exposed at 800 °C for 2000 h under 1 bar pressure, in a pure water steam system. The results revealed that all exposed materials showed relatively low weight gain, with no spallation of the oxide scale within the 2000 h of exposure. XRD analysis showed that Ni-based alloys developed an oxide scale consisting of four main phases: Cr2O3 (alloy 617, Haynes® 282®, alloy 263 and Haynes® 230®), MnCr2O4 (alloy 617, Haynes® 282® and Haynes® 230®), NiCr2O4 (alloy 617) and TiO2 (alloy 263, Haynes® 282®). In contrast, advanced steels showed the development of Cr2O3, MnCr2O4, Mn7SiO12, FeMn(SiO4) and SiO2 phases. The steel with the highest Cr content showed the formation of Fe3O4 and the thickest oxide scale.

  18. Steam Oxidation Behavior of Advanced Steels and Ni-Based Alloys at 800 °C

    NASA Astrophysics Data System (ADS)

    Dudziak, T.; Boroń, L.; Deodeshmukh, V.; Sobczak, J.; Sobczak, N.; Witkowska, M.; Ratuszek, W.; Chruściel, K.

    2017-03-01

    This publication studies the steam oxidation behavior of advanced steels (309S, 310S and HR3C) and Ni-based alloys (Haynes® 230®, alloy 263, alloy 617 and Haynes® 282®) exposed at 800 °C for 2000 h under 1 bar pressure, in a pure water steam system. The results revealed that all exposed materials showed relatively low weight gain, with no spallation of the oxide scale within the 2000 h of exposure. XRD analysis showed that Ni-based alloys developed an oxide scale consisting of four main phases: Cr2O3 (alloy 617, Haynes® 282®, alloy 263 and Haynes® 230®), MnCr2O4 (alloy 617, Haynes® 282® and Haynes® 230®), NiCr2O4 (alloy 617) and TiO2 (alloy 263, Haynes® 282®). In contrast, advanced steels showed the development of Cr2O3, MnCr2O4, Mn7SiO12, FeMn(SiO4) and SiO2 phases. The steel with the highest Cr content showed the formation of Fe3O4 and the thickest oxide scale.

  19. Plastic Instabilities and Their Consequences in Steels and Other High Strength Alloys

    DTIC Science & Technology

    1991-09-01

    rate yes Superalloys * Alloy 600 quasi-static no Rend 41 quasi-static no Steels * HY80 quasi-static no ultra-soft5 no low temperatures no AISI 4340...AD-A240 976 ([f) A Final Technical Report Contract No. N00014-88-K-0111 S PLASTIC INSTABILITIES AND THEIR CONSEQUENCES IN STEELS AND OTHER HIGH...PLASTIC INSTABILITIES AND THEIR CONSEQUENCES IN STEELS AND OTHER HIGH STRENGTH ALLOYS Submitted to: Office of Naval Research 800 North Quincy Street

  20. Self-Pierce Riveting of Three Aluminium Alloy and Mild Steel Sheets

    SciTech Connect

    Mori, K.; Abe, Y.; Sakai, S.; Kato, T.

    2010-06-15

    Three aluminium alloy and steel sheets were joined with a self-piercing rivet. Self-pierce riveting has the function of joining steel and aluminium alloys having very different melting points due to plastic joining. The requisites for joining the three sheets are the driving of the rivet leg through the middle sheet, the flaring of the rivet leg in the lower sheet and the prevention of the fracture of the lower sheet. The joinability for various combinations of the three sheets was determined. When the rivet leg is small, no driving through the middle sheet occurs, the lower sheet ruptures for a large rivet leg. In addition, 980 MPa high strength steel, mild steel and aluminium alloy sheets were joined by the self-pierce riveting.

  1. Self-Pierce Riveting of Three Aluminium Alloy and Mild Steel Sheets

    NASA Astrophysics Data System (ADS)

    Mori, K.; Abe, Y.; Kato, T.; Sakai, S.

    2010-06-01

    Three aluminium alloy and steel sheets were joined with a self-piercing rivet. Self-pierce riveting has the function of joining steel and aluminium alloys having very different melting points due to plastic joining. The requisites for joining the three sheets are the driving of the rivet leg through the middle sheet, the flaring of the rivet leg in the lower sheet and the prevention of the fracture of the lower sheet. The joinability for various combinations of the three sheets was determined. When the rivet leg is small, no driving through the middle sheet occurs, the lower sheet ruptures for a large rivet leg. In addition, 980 MPa high strength steel, mild steel and aluminium alloy sheets were joined by the self-pierce riveting.

  2. Finite Element Simulation of Plastic Joining Processes of Steel and Aluminum Alloy Sheets

    SciTech Connect

    Mori, K.; Abe, Y.; Kato, T.

    2007-05-17

    Various high tensile strength steel sheets and an aluminum alloy sheet were joined with a self-piercing rivet. It is not easy to weld the aluminum alloy sheet and high tensile strength sheets by means of conventional resistance welding because of very different melting points. To obtain optimum joining conditions, joining defects were categorized into separation of the sheets and an inner fracture. The joining range of ultra high tensile strength steel and aluminum alloy sheets was extended by means of dies optimized by finite element simulation. The joint strength is greatly influenced by not only the strength of the sheets and rivets but also the ratio of the thickness of the lower sheet to the total thickness. In addition, mechanical clinching of high strength steel and aluminum alloy sheets was simulated.

  3. Finite Element Simulation of Plastic Joining Processes of Steel and Aluminum Alloy Sheets

    NASA Astrophysics Data System (ADS)

    Mori, K.; Abe, Y.; Kato, T.

    2007-05-01

    Various high tensile strength steel sheets and an aluminum alloy sheet were joined with a self-piercing rivet. It is not easy to weld the aluminum alloy sheet and high tensile strength sheets by means of conventional resistance welding because of very different melting points. To obtain optimum joining conditions, joining defects were categorized into separation of the sheets and an inner fracture. The joining range of ultra high tensile strength steel and aluminum alloy sheets was extended by means of dies optimized by finite element simulation. The joint strength is greatly influenced by not only the strength of the sheets and rivets but also the ratio of the thickness of the lower sheet to the total thickness. In addition, mechanical clinching of high strength steel and aluminum alloy sheets was simulated.

  4. The success and limitations of high alloy stainless steels in seawater service

    SciTech Connect

    Gallagher, P.; Malpas, R.E. )

    1989-01-01

    The performance of high alloy stainless steels has been determined in chlorinated natural seawater in large scale and prototype seawater handling systems consisting of pumps, pipework and valves at ambient North Sea temperatures. In addition the influence of temperature on the corrosion characteristics of these alloys has been investigated. The results show that austenitic stainless steels with minimum molybdenum and nitrogen contents of 6% and 0.2% respectively and high alloy duplex stainless steels with minimum compositions of 25% Cr, 3% Mo and 0.15% N can be successfully used for the fabrication of seawater systems handling North Sea ambient or heated seawater. These alloys have some limitations, however, in areas of heat transfer, particularly where air spaces are present in a system; where dissimilar metal crevices are present and at positions where fretting can occur.

  5. Study of austenitic stainless steel welded with low alloy steel filler metal. [tensile and impact strength tests

    NASA Technical Reports Server (NTRS)

    Burns, F. A.; Dyke, R. A., Jr.

    1979-01-01

    The tensile and impact strength properties of 316L stainless steel plate welded with low alloy steel filler metal were determined. Tests were conducted at room temperature and -100 F on standard test specimens machined from as-welded panels of various chemical compositions. No significant differences were found as the result of variations in percentage chemical composition on the impact and tensile test results. The weldments containing lower chromium and nickel as the result of dilution of parent metal from the use of the low alloy steel filler metal corroded more severely in a marine environment. The use of a protective finish, i.e., a nitrile-based paint containing aluminum powder, prevented the corrosive attack.

  6. Effect of Alloy 625 Buffer Layer on Hardfacing of Modified 9Cr-1Mo Steel Using Nickel Base Hardfacing Alloy

    NASA Astrophysics Data System (ADS)

    Chakraborty, Gopa; Das, C. R.; Albert, S. K.; Bhaduri, A. K.; Murugesan, S.; Dasgupta, Arup

    2016-04-01

    Dashpot piston, made up of modified 9Cr-1Mo steel, is a part of diverse safety rod used for safe shutdown of a nuclear reactor. This component was hardfaced using nickel base AWS ER NiCr-B alloy and extensive cracking was experienced during direct deposition of this alloy on dashpot piston. Cracking reduced considerably and the component was successfully hardfaced by application of Inconel 625 as buffer layer prior to hardface deposition. Hence, a separate study was undertaken to investigate the role of buffer layer in reducing the cracking and on the microstructure of the hardfaced deposit. Results indicate that in the direct deposition of hardfacing alloy on modified 9Cr-1Mo steel, both heat-affected zone (HAZ) formed and the deposit layer are hard making the thickness of the hard layer formed equal to combined thickness of both HAZ and deposit. This hard layer is unable to absorb thermal stresses resulting in the cracking of the deposit. By providing a buffer layer of Alloy 625 followed by a post-weld heat treatment, HAZ formed in the modified 9Cr-1Mo steel is effectively tempered, and HAZ formed during the subsequent deposition of the hardfacing alloy over the Alloy 625 buffer layer is almost completely confined to Alloy 625, which does not harden. This reduces the cracking susceptibility of the deposit. Further, unlike in the case of direct deposition on modified 9Cr-1Mo steel, dilution of the deposit by Ni-base buffer layer does not alter the hardness of the deposit and desired hardness on the deposit surface could be achieved even with lower thickness of the deposit. This gives an option for reducing the recommended thickness of the deposit, which can also reduce the risk of cracking.

  7. Comparative MRI compatibility of 316 L stainless steel alloy and nickel-titanium alloy stents.

    PubMed

    Holton, Andrea; Walsh, Edward; Anayiotos, Andreas; Pohost, Gerald; Venugopalan, Ramakrishna

    2002-01-01

    The initial success of coronary stenting is leading to a proliferation in peripheral stenting. A significant portion of the stents used in a clinical setting are made of 316 low carbon stainless steel (SS). Other alloys that have been used for stent manufacture include tantalum, MP35N, and nickel-titanium (NiTi). The ferromagnetic properties of SS cause the production of artifacts in magnetic resonance imaging (MRI). The NiTi alloys, in addition to being known for their shape memory or superelastic properties, have been shown to exhibit reduced interference in MRI. Thus, the objective of this study was to determine the comparative MRI compatibility of SS and NiTi stents. Both gradient echo and spin-echo images were obtained at 1.5 and 4.1 T field strengths. The imaging of stents of identical geometry but differing compositions permitted the quantification of artifacts produced due to device composition by normalizing the radio frequency shielding effects. These images were analyzed for magnitude and spatial extent of signal loss within the lumen and outside the stent. B1 mapping was used to quantify the attenuation throughout the image. The SS stent caused significant signal loss and did not allow for visibility of the lumen. However, the NiTi stent caused only minor artifacting and even allowed for visualization of the signal from within the lumen. In addition, adjustments to the flip angle of standard imaging protocols were shown to improve the quality of signal from within the lumen.

  8. [Study on the multivariate quantitative analysis method for steel alloy elements using LIBS].

    PubMed

    Gu, Yan-hong; Li, Ying; Tian, Ye; Lu, Yuan

    2014-08-01

    Quantitative analysis of steel alloys was carried out using laser induced breakdown spectroscopy (LIBS) taking into account the complex matrix effects in steel alloy samples. The laser induced plasma was generated by a Q-switched Nd:YAG laser operating at 1064 nm with pulse width of 10 ns and repeated frequency of 10 Hz. The LIBS signal was coupled to the echelle spectrometer and recorded by a high sensitive ICCD detector. To get the best experimental conditions, some parameters, such as the detection delay, the CCDs integral gate width and the detecting position from the sample surface, were optimized. The experimental results showed that the optimum detection delay time was 1.5 micros, the optimal CCDs integral gate width was 2 micros and the best detecting position was 1.5 mm below the alloy sample's surface. The samples used in the experiments are ten standard steel alloy samples and two unknown steel alloy samples. The quantitative analysis was investigated with the optimum experimental parameters. Elements Cr and Ni in steel alloy samples were taken as the detection targets. The analysis was carried out with the methods based on conditional univariate quantitative analysis, multiple linear regression and partial least squares (PLS) respectively. It turned out that the correlation coefficients of calibration curves are not very high in the conditional univariate calibration method. The analysis results were obtained with the unsatisfied relative errors for the two predicted samples. So the con- ditional univariate quantitative analysis method can't effectively serve the quantitative analysis purpose for multi-components and complex matrix steel alloy samples. And with multiple linear regression method, the analysis accuracy was improved effectively. The method based on partial least squares (PLS) turned out to be the best method among all the three quantitative analysis methods applied. Based on PLS, the correlation coefficient of calibration curve for Cr is 0

  9. 78 FR 35248 - Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Final Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-12

    ... International Trade Administration Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Final... order on circular welded non-alloy steel pipe (CWP) from the Republic of Korea (Korea) for the period... Republic of Korea: Preliminary Results of Antidumping Duty Administrative Review; 2010-2011, 77 FR...

  10. 78 FR 28190 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-14

    ... International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Final Results of... carbon and certain alloy steel wire rod (wire rod) from Mexico. The period of review (POR) is October 1... Federal Register the Preliminary Results of the antidumping duty administrative review of wire rod...

  11. 78 FR 60850 - Carbon and Certain Alloy Steel Wire Rod From Brazil: Final Results of the Expedited Second Sunset...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-02

    ... International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Brazil: Final Results of the... certain alloy steel wire rod (wire rod) from Brazil would be likely to lead to continuation or recurrence... Department initiated the second sunset review of the CVD order \\1\\ on wire rod from Brazil pursuant...

  12. 78 FR 63450 - Carbon and Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico, Moldova, Trinidad and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-24

    ... International Trade Administration, Carbon and Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico... on carbon and certain alloy steel wire rod (``wire rod'') from Brazil, Indonesia, Mexico, Moldova... Brazil, Indonesia, Mexico, Moldova, Trinidad and Tobago, and Ukraine, pursuant to section 751(c) of...

  13. 75 FR 44763 - Certain Circular Welded Non-Alloy Steel Pipe From Mexico; Extension of Time Limit for Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-29

    ... International Trade Administration Certain Circular Welded Non-Alloy Steel Pipe From Mexico; Extension of Time... welded non- alloy steel pipe from Mexico. We also received review requests on November 30, 2009, from... require additional time with respect to cost of production data used in the margin calculation...

  14. 78 FR 25253 - Seamless Carbon and Alloy Steel Standard, Line, and Pressure From the People's Republic of China...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-30

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Seamless Carbon and Alloy Steel Standard, Line, and Pressure From the People... seamless carbon and alloy steel standard, line, and pressure pipe ] (``seamless pipe'') from the...

  15. 75 FR 69052 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-10

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe..., and pressure pipe (``seamless pipe'') from the People's Republic of China (``PRC''). In addition, the... and Alloy Steel Standard, Line, and Pressure Pipe from the People's Republic of China:...

  16. 78 FR 33809 - Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-05

    ... Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's Republic of China: Rescission..., line, and pressure pipe from the People's Republic of China. The period of review is November 1, 2011... order on seamless carbon and alloy steel standard, line, and pressure pipe from the People's Republic...

  17. 75 FR 6183 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-08

    ... Pressure Pipe from the People's Republic of China: Postponement of Preliminary Determination of Antidumping... investigation on certain seamless carbon and alloy steel standard, line, and pressure pipe from the People's Republic of China. See Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From...

  18. 76 FR 40689 - Certain Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Extension of Time Limit...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-11

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Certain Circular Welded Non-Alloy Steel Pipe From the Republic of Korea... administrative review of the antidumping duty order on certain circular welded non- alloy steel pipe...

  19. 75 FR 39917 - Circular Welded Non-Alloy Steel Pipe from the Republic of Korea: Extension of Time Limit for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-13

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration (A-580-809) Circular Welded Non-Alloy Steel Pipe from the Republic of Korea... non-alloy steel pipe from the Republic of Korea, covering the period November 1, 2008 through...

  20. 76 FR 34044 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Extension of Time Limits for the Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-10

    ... From the Federal Register Online via the Government Publishing Office ] DEPARTMENT OF COMMERCE International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Extension of Time Limits... administrative review of the antidumping duty order on carbon and certain alloy steel wire rod from...

  1. 76 FR 52636 - Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Partial Rescission of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-23

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Partial... the antidumping duty order on certain circular welded non-alloy steel pipe (``circular welded...

  2. 75 FR 13729 - Circular Welded Non-Alloy Steel Pipe from the Republic of Korea: Extension of Time Limit for the...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-23

    ... International Trade Administration Circular Welded Non-Alloy Steel Pipe from the Republic of Korea: Extension of... circular welded non-alloy steel pipe from the Republic of Korea, covering the period November 1, 2007 through October 31, 2008. See Circular Welded Non-Alloy Steel Pipe from the Republic of Korea:...

  3. Microstructural development of diffusion-brazed austenitic stainless steel to magnesium alloy using a nickel interlayer

    SciTech Connect

    Elthalabawy, Waled M.; Khan, Tahir I.

    2010-07-15

    The differences in physical and metallurgical properties of stainless steels and magnesium alloys make them difficult to join using conventional fusion welding processes. Therefore, the diffusion brazing of 316L steel to magnesium alloy (AZ31) was performed using a double stage bonding process. To join these dissimilar alloys, the solid-state diffusion bonding of 316L steel to a Ni interlayer was carried out at 900 deg. C followed by diffusion brazing to AZ31 at 510 deg. C. Metallographic and compositional analyses show that a metallurgical bond was achieved with a shear strength of 54 MPa. However, during the diffusion brazing stage B{sub 2} intermetallic compounds form within the joint and these intermetallics are pushed ahead of the solid/liquid interface during isothermal solidification of the joint. These intermetallics had a detrimental effect on joint strengths when the joint was held at the diffusion brazing temperature for longer than 20 min.

  4. Cryo-quenched Fe-Ni-Cr alloy single crystals: A new decorative steel

    SciTech Connect

    Boatner, Lynn A.; Kolopus, James A.; Lavrik, Nicolay V.; Phani, P. Sudharshan

    2016-08-31

    In this paper, a decorative steel is described that is formed by a process that is unlike that of the fabrication methods utilized in making the original Damascus steels over 2000 years ago. The decorative aspect of the steel arises from a three-dimensional surface pattern that results from cryogenically quenching polished austenitic alloy single crystals into the martensitic phase that is present below 190 K. No forging operations are involved – the mechanism is entirely based on the metallurgical phase properties of the ternary alloy. The symmetry of the decorative pattern is determined and controlled by the crystallographic orientation and symmetry of the 70%Fe,15%Ni,15%Cr alloy single crystals. Finally, in addition to using “cuts” made along principal crystallographic surface directions, an effectively infinite number of other random-orientation “cuts” can be utilized to produce decorative patterns where each pattern is unique after the austenitic-to-martensitic phase transformation.

  5. Complex alloy steel for heavily loaded carburized gear wheels

    NASA Astrophysics Data System (ADS)

    Tel'dekov, V. A.; Merilova, E. A.; Shevchuk, V. P.

    1987-05-01

    The tendency of steel 18KhGN2MFB towards internal oxidation and austenite grain growth during CHT is markedly lower than for steel 20KhNZA normally used for gear wheels. Steel 18KhGN2MFB has sufficiently high hardenability for the carburized and carbonitrided layers.

  6. Effects of mechanical alloying time on microstructure and properties of 9Cr-ODS steels

    NASA Astrophysics Data System (ADS)

    Xie, Rui; Lu, Zheng; Lu, Chenyang; Liu, Chunming

    2014-12-01

    Pre-alloyed powders of oxide dispersion strengthened (ODS) steels were produced by atomization. The atomized powders without mechanical alloying (MA) and with short-time MA were consolidated by hot isostatic pressing (HIP). The morphology and microstructure of the atomized and the MA powders were studied by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The microstructure of 9Cr-ODS steels with different MA time was characterized by high-resolution transmission electron microscopy (HRTEM), electron backscatter diffraction (EBSD) and atom probe tomography (APT). The results showed that high-density of nanosized precipitates and ultrafine grains are formed in the ODS steels using the processing route, which remarkably reduce MA time. The yield strength and ultimate tensile strength of ODS steels are improved with the increase of MA time.

  7. Load carrying capacity of RCC beams by replacing steel reinforcement bars with shape memory alloy bars

    NASA Astrophysics Data System (ADS)

    Bajoria, Kamal M.; Kaduskar, Shreya S.

    2016-04-01

    In this paper the structural behavior of reinforced concrete (RC) beams with smart rebars under two point loading system has been numerically studied, using Finite Element Method. The material used in this study is Super-elastic Shape Memory Alloys (SE SMAs) which contains nickel and titanium. In this study, different quantities of steel and SMA rebars have been used for reinforcement and the behavior of these models under two point bending loading system is studied. A comparison of load carrying capacity for the model between steel reinforced concrete beam and the beam reinforced with S.M.A and steel are performed. The results show that RC beams reinforced with combination of shape memory alloy and steel show better performance.

  8. Laser Surface Alloying of SUS316 Stainless Steel with Al-Si

    NASA Astrophysics Data System (ADS)

    Zherebtsov, Sergey; Maekawa, Katsuhiro; Hayashi, Terutake; Futakawa, Masatoshi

    The effect of varying temperature of the type 316 stainless steel substrate on the structure and properties of laser alloyed layer was investigated. The material for alloying (Al-Si powder mixture) was placed on the surface of stainless steel substrate by pasting. The surface was scanned by a pulsed Nd: YAG laser beam to achieve surface alloying. The temperature of substrate continuously increased during laser treatment to about 830°C. The microstructure, chemical and phase composition and microhardness of the modified layer were studied then. It has been found that four different types of structure were formed in the alloyed zone depending on the temperature of the substrate. These structures differ from each other in phase composition, microhardness and relation to cracking. Based on the results, optimal parameters for the production of a uniform, crack-free layer with a high hardness were developed.

  9. Submerged Arc Welding Consumables for HSLA (High Strength Low Alloy)-100 Steel

    DTIC Science & Technology

    1989-06-01

    0.001 Manganese 0.02 Silicon 0.01 Phosphorus 0.002 Sulfur 0.001 Nickel 0.05 Molybdenum 0.01 Chromium 0.02 Vanadium 0.001 Aluminum 0.002 Titanium 0.002...carbon-manganese steels with small amounts of alloys added such as aluminum, titanium , niobium , or vanadium . Since these steels exhibit high strength...83 Chemical check analysis for boron and phosphorus ................................................. 88 Mechanical property data summary

  10. Effect of alloying additions on secondary hardening behavior of Mo-containing steels

    NASA Astrophysics Data System (ADS)

    Kwon, H.; Lee, J. H.; Lee, K. B.; Kim, C. M.; Yang, H. R.

    1997-03-01

    The effect of alloying additions on secondary hardening behavior in Fe-Mo-C steels has been investigated by means of the successive alloying additions of Cr, Co, and Ni. The Cr additions promote M3C cementite formation. The Ni additions destabilize the cementite formation, while the Co additions retard dislocation recovery and present the necessary sites for M2C formation which provides the secondary hardening.

  11. Effect of Alloying Element Partition in Pearlite on the Growth of Austenite in High-Carbon Low Alloy Steel

    NASA Astrophysics Data System (ADS)

    Yang, Z. N.; Xia, Y.; Enomoto, M.; Zhang, C.; Yang, Z. G.

    2016-03-01

    The growth of austenite from pearlite in high-carbon low alloy steel occurs with and without alloy element redistribution depending on the amount of superheating above the eutectoid temperature. The transition temperature of austenite growth (denoted PNTT) is calculated as a function of pearlite transformation temperature and subsequent holding time, which affect the degree of partitioning in pearlite, using experimental partition coefficients k θ/ α of Mn, Cr, Co, Si, and Ni reported in the literature. PNTT is the highest in Cr-containing alloys which have the largest k θ/ α in pearlite. Post-transformation aging, usually accompanied by cementite spheroidization, leads to a marked increase of PNTT in Mn and Cr alloys. PNTT of Ni alloy does not depend on pearlite transformation temperature because practically the formation of partitioned pearlite is severely limited in this alloy for kinetic reasons. Above PNTT, austenite growth occurs fast initially, but slows down in the order of ten seconds when the ferrite disappears, and the remaining small carbide particles dissolve very slowly under the control of alloy element diffusion.

  12. Effects of LWR environments on fatigue life of carbon and low-alloy steels

    SciTech Connect

    Chopra, O.K.; Shack, W.J.

    1995-03-01

    SME Boiler and Pressure Vessel Code provides construction of nuclear power plant components. Figure I-90 Appendix I to Section III of the Code specifies fatigue design curves for structural materials. While effects of environments are not explicitly addressed by the design curves, test data suggest that the Code fatigue curves may not always be adequate in coolant environments. This paper reports the results of recent fatigue tests that examine the effects of steel type, strain rate, dissolved oxygen level, strain range, loading waveform, and surface morphology on the fatigue life of A 106-Gr B carbon steel and A533-Gr B low-alloy steel in water.

  13. High-Temperature Thermomechanical Treatment of Alloyed Structural and Tool Steels

    NASA Astrophysics Data System (ADS)

    Smirnov, V. A.; Filatov, V. I.

    2015-01-01

    The effect of hot plastic deformation on decomposition of supercooled austenite in some structural and die steels with different contents of carbon and alloying elements is investigated. It is shown that high-temperature plastic deformation accelerates the transformation of supercooled austenite by the diffusion mechanism and decelerates the development of bainitic transformations by raising the hardenability of the steels. The general laws of formation of mechanical properties under high-temperature thermomechanical treatment of structural and die steels after low- and high-temperature tempering are studied.

  14. Development of microstructure in high-alloy steel K390 using semi-solid forming

    NASA Astrophysics Data System (ADS)

    Opatova, K.; Aisman, D.; Rubesova, K.; Ibrahim, K.; Jenicek, S.

    2016-03-01

    Semi-solid processing of light alloys, namely aluminium and magnesium alloys, is a widely known and well-established process. By contrast, processing of powder steels which have high levels of alloying elements is a rather new subject of research. Thixoforming of high-alloy steels entails a number of technical difficulties. If these are overcome, the method can offer a variety of benefits. First of all, the final product shape and the desired mechanical properties can be obtained using a single forming operation. Semi-solid forming can produce unusual powder steel microstructures unattainable by any other route. Generally, the microstructures, which are normally found in thixoformed steels, consist of large fractions of globular or polygonal particles of metastable austenite embedded in a carbide network. An example is the X210Cr12 steel which is often used for semi-solid processing experiments. A disadvantage of the normal microstructure configuration is the brittleness of the carbide network, in which cracks initiate and propagate, causing low energy fractures. However, there is a newly-developed mini-thixoforming route which produces microstructures with an inverted configuration. Here, the material chosen for this purpose was K390 steel, in which the content of alloying elements is up to 24%. Its microstructure which was obtained by mini- thixoforming did not contain polyhedral austenite grains but hard carbides embedded in a ductile austenitic matrix. This provided the material with improved toughness. The spaces between the austenite grains were filled with a eutectic in which chromium, molybdenum and cobalt were distributed uniformly. After the processing parameters were optimized, complexshaped demonstration products were manufactured by this route. These products showed an extraordinary compressive strength and high wear resistance, thanks to the hardness of their microstructure constituents, predominantly the carbides.

  15. Surface microstructures and antimicrobial properties of copper plasma alloyed stainless steel

    NASA Astrophysics Data System (ADS)

    Zhang, Xiangyu; Huang, Xiaobo; Jiang, Li; Ma, Yong; Fan, Ailan; Tang, Bin

    2011-12-01

    Bacterial adhesion to stainless steel surfaces is one of the major reason causing the cross-contamination and infection in many practical applications. An approach to solve this problem is to enhance the antibacterial properties on the surface of stainless steel. In this paper, novel antibacterial stainless steel surfaces with different copper content have been prepared by a plasma surface alloying technique at various gas pressures. The microstructure of the alloyed surfaces was investigated using glow discharge optical emission spectroscopy (GDOES) and scanning electron microscopy (SEM). The viability of bacteria attached to the antibacterial surfaces was tested using the spread plate method. The antibacterial mechanism of the alloyed surfaces was studied by X-ray photoelectron spectroscopy (XPS). The results indicate that gas pressure has a great influence on the surface elements concentration and the depth of the alloyed layer. The maximum copper concentration in the alloyed surface obtained at the gas pressure of 60 Pa is about 7.1 wt.%. This alloyed surface exhibited very strong antibacterial ability, and an effective reduction of 98% of Escherichia coli (E. coli) within 1 h was achieved by contact with the alloyed surface. The maximum thickness of the copper alloyed layer obtained at 45 Pa is about 6.5 μm. Although the rate of reduction for E. coli of this alloyed surface was slower than that of the alloyed surface with the copper content about 7.1 wt.% over the first 3 h, few were able to survive more than 12 h and the reduction reached over 99.9%. The XPS analysis results indicated that the copper ions were released when the copper alloyed stainless steel in contact with bacterial solution, which is an important factor for killing bacteria. Based on an overall consideration of bacterial killing rate and durability, the alloyed surface with the copper content of 2.5 wt.% and the thickness of about 6.5 μm obtained at the gas pressure of 45 Pa is expected

  16. High-strength economically alloyed corrosion-resistant steels with the structure of nitrogen martensite

    NASA Astrophysics Data System (ADS)

    Bannykh, O.; Blinov, V.; Lukin, E.

    2016-04-01

    The use of nitrogen as the main alloying element allowing one both to increase the corrosion resistance and mechanical properties of steels and to improve their processability is a new trend in physical metallurgy of high-strength corrosion resistant steels. The principles of alloying, which are developed for high-nitrogen steel in IMET RAS, ensure the formation of the structure, which contains predetermined amounts of martensite (70-80%) and austenite (20-30%) and is free from δ-ferrite, σ-phase, and Cr23C6 carbide. These principles were used as the base for the creation of new high-strength corrosion-resistant weldable and deformable 0Kh16AN5B, 06Kh16AN4FD, 08Kh14AN4MDB, 09Kh16AN3MF, 27Kh15AN3MD2, 40Kh13AN3M2, and 19Kh14AMB steels, which are operative at temperatures ranging from - 70 to 400°C. The developed nitrogen-containing steels compared with similar carbon steels are characterized by a higher resistance to pitting and crevice corrosion and are resistant to stress corrosion cracking. The new steels successfully passed trial tests as heavy duty articles.

  17. Development of a Nitrogen-Modified Stainless-Steel Hardfacing Alloy

    NASA Astrophysics Data System (ADS)

    Smith, Ryan Thomas

    A 2nd generation hardfacing alloy, Nitromaxx, has been designed though an integrated approach of chemical modification, characterization, and testing. Nitromaxx is a stainless-steel alloy modified with 0.5wt% nitrogen which has improved elevated temperature properties and wear performance. This is achieved by changing both the microstructure phase balance and inherent deformation characteristics of the metal. The alloy is fabricated by a powder metallurgy-hot isostatic pressing (PM-HIP) method, rather than traditional cladding methods. This allows for alloy property modification by equilibrium heat treatment while eliminating significant fabrication defects, so that component life is extended wear and galling performance is improved. The design approach involved extensive characterization of severely worn and galled surfaces of the 1st generation of hardfacing alloys. Observation of samples after galling testing showed highly inhomogeneous deformation in regions of the gall scar, leading to the design hypothesis that strain-localization is a controlling mechanism in severe wear of stainless-steels. Additionally, the presence and subsequent loss was investigated and correlated microstructurally to the transition to poor galling behavior in the existing stainless steel hardfacing NOREM02. This provided new insight and identification of key microstructural and mechanical properties that improve galling performance: 1) increased strain-hardening rate in the metal matrix at elevated temperature, 2) increased yield strength in the matrix leading to higher hardness, and 3) increased volume fraction of hard, non-deforming phases. All of these alloy design goals can be realized by the addition of nitrogen, which 1) at high concentration is shown to lower the stacking fault energy in the stainless steel matrix, 2) increases interstitial matrix strengthening, and 3) increases the volume fraction of nitride phases. These observations have been confirmed qualitatively and

  18. Transformation process for production of ultrahigh carbon steels and new alloys

    DOEpatents

    Strum, Michael J.; Goldberg, Alfred; Sherby, Oleg D.; Landingham, Richard L.

    1995-01-01

    Ultrahigh carbon steels with superplastic properties are produced by heating a steel containing ferrite and carbide phases to a soaking temperature approximately 50.degree. C. above the A.sub.1 transformation temperature, soaking the steel above the A.sub.1 temperature for a sufficient time that the major portion of the carbides dissolve into the austenite matrix, and then cooling the steel in a controlled manner within predetermined limits of cooling rate or transformation temperature, to obtain a steel having substantially spheroidal carbides. New alloy compositions contain aluminum and solute additions which promote the formation of a fine grain size and improve the resistance of the carbides to coarsening at the forming temperature.

  19. Transformation process for production of ultrahigh carbon steels and new alloys

    DOEpatents

    Strum, M.J.; Goldberg, A.; Sherby, O.D.; Landingham, R.L.

    1995-08-29

    Ultrahigh carbon steels with superplastic properties are produced by heating a steel containing ferrite and carbide phases to a soaking temperature approximately 50 C above the A{sub 1} transformation temperature, soaking the steel above the A{sub 1} temperature for a sufficient time that the major portion of the carbides dissolve into the austenite matrix, and then cooling the steel in a controlled manner within predetermined limits of cooling rate or transformation temperature, to obtain a steel having substantially spheroidal carbides. New alloy compositions contain aluminum and solute additions which promote the formation of a fine grain size and improve the resistance of the carbides to coarsening at the forming temperature. 9 figs.

  20. A comparison of fracture behavior of low alloy steel with different sizes of carbide particles

    SciTech Connect

    Wang, G.Z.; Chen, J.H.

    1996-07-01

    The fracture behaviors of low alloy steels with similar grain sizes but different sizes of carbide particles were investigated using precracked and notched specimens. The results indicate that in precracked specimens (COD), steel with coarser carbide particles has a lower toughness than steel with finer carbide particles over a temperature range from {minus}196 C to {minus}90 C. However, in notched specimens (four-point bending (4PB) and Charpy V), these two steels shows similar toughness at low temperature where specimens are fractured by cleavage without fibrous cracking. In the transition temperature range, the steel with coarser carbide particles conversely shows a little higher toughness due to the longer extension length of the fibrous crack. This phenomenon indicates that in precracked specimens, the second-phase particles play a leading role in cleavage fracture, while in notched specimens, the grain size dominates the fracture behavior.

  1. 77 FR 59892 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Affirmative Final Determination of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-01

    ... International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Affirmative Final... determine that shipments of wire rod with an actual diameter of 4.75 mm to 5.00 mm by Deacero S.A. de C.V... included within the scope of the order on wire rod from Mexico. Further, we continue to determine...

  2. Study made of corrosion resistance of stainless steel and nickel alloys in nuclear reactor superheaters

    NASA Technical Reports Server (NTRS)

    Greenberg, S.; Hart, R. K.; Lee, R. H.; Ruther, W. E.; Schlueter, R. R.

    1967-01-01

    Experiments performed under conditions found in nuclear reactor superheaters determine the corrosion rate of stainless steel and nickel alloys used in them. Electropolishing was the primary surface treatment before the corrosion test. Corrosion is determined by weight loss of specimens after defilming.

  3. 77 FR 19711 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From Germany...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-02

    ... COMMISSION Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From Germany... pressure pipe (``seamless pipe'') from Germany would be likely to lead to continuation or recurrence of..., ] and pressure pipe and tube not more than 4.5 inches in outside diameter, and including redraw...

  4. Use of steel and tantalum apparatus for molten Cd-Mg-Zn alloys

    NASA Technical Reports Server (NTRS)

    Bennett, G. A.; Burris, L., Jr.; Kyle, M. L.; Nelson, P. A.

    1966-01-01

    Steel and tantalum apparatus contains various ternary alloys of cadmium, zinc, and magnesium used in pyrochemical processes for the recovery of uranium-base reactor fuels. These materials exhibit good corrosion resistance at the high temperatures necessary for fuel separation in liquid metal-molten salt solvents.

  5. Characterization of Nonmetallic Inclusions in High-Manganese and Aluminum-Alloyed Austenitic Steels

    NASA Astrophysics Data System (ADS)

    Park, Joo Hyun; Kim, Dong-Jin; Min, Dong Joon

    2012-07-01

    The effects of Al and Mn contents on the size, composition, and three-dimensional morphologies of inclusions formed in Fe- xMn- yAl ( x = 10 and 20 mass pct, y = 1, 3, and 6 mass pct) steels were investigated to enhance our understanding of the inclusion formation behavior in high Mn-Al-alloyed steels. By assuming that the alumina is a dominant oxide compound, the volume fraction of inclusions estimated from the chemical analysis, i.e., insoluble Al, in the Fe-Mn-3Al steels was larger than the inclusion volume fractions in the Fe-Mn-1Al and Fe-Mn-6Al steels. A similar tendency was found in the analysis of inclusions from a potentiostatic electrolytic extraction method. This finding could be explained from the terminal velocities of the compounds, which was affected by the thermophysical properties of Fe-Mn-Al steels. The inclusions formed in the Fe-Mn-Al-alloyed steels are classified into seven types according to chemistry and morphology: (1) single Al2O3 particle, (2) single AlN or AlON particle, (3) MnAl2O4 single galaxite spinel particle, (4) Al2O3(-Al(O)N) agglomerate, (5) single Mn(S,Se) particle, (6) oxide core with Mn(S,Se) skin (wrap), and (7) Mn(S,Se) core with Al2O3(-Al(O)N) aggregate (or bump). The Mn(S,Se) compounds were formed by the contamination of the steels by Se from the electrolytic Mn. Therefore, the raw materials (Mn) should be used carefully in the melting and casting processes of Fe-Mn-Al-alloyed steels.

  6. Influence of Processing and Heat Treatment on Corrosion Resistance and Properties of High Alloyed Steel Coatings

    NASA Astrophysics Data System (ADS)

    Hill, Horst; Weber, Sebastian; Raab, Ulrich; Theisen, Werner; Wagner, Lothar

    2012-09-01

    Corrosion and abrasive wear are two important aspects to be considered in numerous engineering applications. Looking at steels, high-chromium high-carbon tool steels are proper and cost-efficient materials. They can either be put into service as bulk materials or used as comparatively thin coatings to protect lower alloyed construction or heat treatable steels from wear and corrosion. In this study, two different corrosion resistant tool steels were used for the production of coatings and bulk material. They were processed by thermal spraying and super solidus liquid phase sintering as both processes can generally be applied to produce coatings on low alloyed substrates. Thermally sprayed (high velocity oxygen fuel) coatings were investigated in the as-processed state, which is the most commonly used condition for technical applications, and after a quenching and tempering treatment. In comparison, sintered steels were analyzed in the quenched and tempered condition only. Significant influence of alloy chemistry, processing route, and heat treatment on tribological properties was found. Experimental investigations were supported by computational thermodynamics aiming at an improvement of tribological and corrosive resistance.

  7. Application of nitrogen-alloyed martensitic stainless steels in the aviation industry

    SciTech Connect

    Stein, G.; Kirschner, W.; Lueg, J.

    1997-12-31

    Nitrogen in stainless martensitic steels has a beneficial influence on the mechanical as well as on the chemical properties. However the effect of nitrogen is limited due to the rather low solubility of this element. A special alloy development in combination with a pressurized melting technique lead to distinctly higher nitrogen contents. Stainless martensitic steels containing high nitrogen contents are manufactured by VSG today on an industrial scale using the PESR-process (Pressurized Electroslag Remelting). Depending on special applications these steels are available with different chemical analysis under the trademark CRONIDUR. The basic composition of all CRONIDUR-alloys consists of about 15% Chromium, 1% Molybdenum, 0.15 to 0.35% Carbon and 0.20 to 0.40% Nitrogen. The combination of Cr + Mo + N leads to a superior corrosion resistance of these HNS-steels (HNS: High Nitrogen Steels) in comparison to similar carbon based alloys. Focused on applications with a required minimum hardness of 58 HRC, like stainless bearings or screw shafts, the C+N-content is tuned between 0.60 and 0.80% (Brand: CRONIDUR 30). Additions of max. 0.3% Vanadium and 0.1% Niobium qualifies the brand CRONIDUR 20 for enhanced temperature applications like turbine disks or blades.

  8. Impurity content of reduced-activation ferritic steels and a vanadium alloy

    SciTech Connect

    Klueh, R.L.; Grossbeck, M.L.; Bloom, E.E.

    1997-04-01

    Inductively coupled plasma mass spectrometry was used to analyze a reduced-activation ferritic/martensitic steel and a vanadium alloy for low-level impurities that would compromise the reduced-activation characteristics of these materials. The ferritic steel was from the 5-ton IEA heat of modified F82H, and the vanadium alloy was from a 500-kg heat of V-4Cr-4Ti. To compare techniques for analysis of low concentrations of impurities, the vanadium alloy was also examined by glow discharge mass spectrometry. Two other reduced-activation steels and two commercial ferritic steels were also analyzed to determine the difference in the level of the detrimental impurities in the IEA heat and steels for which no extra effort was made to restrict some of the tramp impurities. Silver, cobalt, molybdenum, and niobium proved to be the tramp impurities of most importance. The levels observed in these two materials produced with present technology exceeded the limits for low activation for either shallow land burial or recycling. The chemical analyses provide a benchmark for the improvement in production technology required to achieve reduced activation; they also provide a set of concentrations for calculating decay characteristics for reduced-activation materials. The results indicate the progress that has been made and give an indication of what must still be done before the reduced-activation criteria can be achieved.

  9. Microstructural Evolution During Friction Stir Welding of Mild Steel and Ni-Based Alloy 625

    NASA Astrophysics Data System (ADS)

    Fernandez, Johnnatan Rodriguez; Ramirez, Antonio J.

    2017-01-01

    Microstructure evolution during friction stir welding (FSW) of mild steel and Ni-based alloy 625 was studied. Regarding the Ni-based alloy, the welding process led to grain refinement caused by discontinuous and continuous dynamic recrystallization, where bulging of the pre-existing grains and subgrain rotation were the primary mechanisms of recrystallization. In the steel, discontinuous dynamic recrystallization was identified as the recovery process experienced by the austenite. Simple shear textures were observed in the regions affected by the deformation of both materials. Although the allotropic transformation obscured the deformation history, the thermo-mechanically affected zone was identified in the steel by simple shear texture components. A new methodology for the study of texture evolution based on rotations of the slip systems using pole figures is presented as an approximation to describe the texture evolution in FSW.

  10. Microstructural Evolution During Friction Stir Welding of Mild Steel and Ni-Based Alloy 625

    NASA Astrophysics Data System (ADS)

    Fernandez, Johnnatan Rodriguez; Ramirez, Antonio J.

    2017-03-01

    Microstructure evolution during friction stir welding (FSW) of mild steel and Ni-based alloy 625 was studied. Regarding the Ni-based alloy, the welding process led to grain refinement caused by discontinuous and continuous dynamic recrystallization, where bulging of the pre-existing grains and subgrain rotation were the primary mechanisms of recrystallization. In the steel, discontinuous dynamic recrystallization was identified as the recovery process experienced by the austenite. Simple shear textures were observed in the regions affected by the deformation of both materials. Although the allotropic transformation obscured the deformation history, the thermo-mechanically affected zone was identified in the steel by simple shear texture components. A new methodology for the study of texture evolution based on rotations of the slip systems using pole figures is presented as an approximation to describe the texture evolution in FSW.

  11. Nondestructive inspection assessment of eddy current and electrochemical analysis to separate inconel and stainless steel alloys

    SciTech Connect

    Moore, D.G.; Sorensen, N.R.

    1998-02-01

    This report presents a nondestructive inspection assessment of eddy current and electrochemical analysis to separate inconel alloys from stainless steel alloys as well as an evaluation of cleaning techniques to remove a thermal oxide layer on aircraft exhaust components. The results of this assessment are presented in terms of how effective each technique classifies a known exhaust material. Results indicate that either inspection technique can separate inconel and stainless steel alloys. Based on the experiments conducted, the electrochemical spot test is the optimum for use by airframe and powerplant mechanics. A spot test procedure is proposed for incorporation into the Federal Aviation Administration Advisory Circular 65-9A Airframe & Powerplant Mechanic - General Handbook. 3 refs., 70 figs., 7 tabs.

  12. Mechanical properties and oxidation and corrosion resistance of reduced-chromium 304 stainless steel alloys

    NASA Technical Reports Server (NTRS)

    Stephens, J. R.; Barrett, C. A.; Gyorgak, C. A.

    1979-01-01

    An experimental program was undertaken to identify effective substitutes for part of the Cr in 304 stainless steel as a method of conserving the strategic element Cr. Although special emphasis was placed on tensile properties, oxidation and corrosion resistance were also examined. Results indicate that over the temperature range of -196 C to 540 C the yield stress of experimental austenitic alloys with only 12 percent Cr compare favorably with the 18 percent Cr in 304 stainless steel. Oxidation resistance and in most cases corrosion resistance for the experimental alloys were comparable to the commercial alloy. Effective substitutes for Cr included Al, Mo, Si, Ti, and V, while Ni and Mn contents were increased to maintain an austenitic structure.

  13. Neutron-irradiated model alloys and pressure-vessel steels studied using positron spectroscopy

    NASA Astrophysics Data System (ADS)

    Cumblidge, Stephen Eric

    We have used positron-annihilation-lifetime spectroscopies to examine microstructural evolution of pressure vessel steels and model alloys that have systematically varied amounts of copper, nickel, and phosphorus during neutron irradiation and post-irradiation annealing. The objective of this work was to characterize the neutron-irradiation induced microstructural features that cause the embrittlement of nuclear reactor pressure-vessel steel. We used positron annihilation lifetime spectroscopy and Doppler-broadening spectroscopy to examine the model alloys and pressure-vessel steels before and after irradiation and after post-irradiation annealing. We followed the changes in the mechanical properties of the materials using Rockwell 15N hardness measurements. The results show that in both the model alloys and pressure-vessel steels neutron irradiation causes the formation of vacancy-type defect clusters and a fine distribution of copper- and nickel-enriched metallic precipitates. The vacancy clusters are small in size and were present in all samples, and disappear upon annealing at 450°C. The metallic precipitates are present only in the model alloy samples with either high Cu or a combination of medium Cu and high Ni, and they remain in the microstructure after annealing up to 550°C, starting to anneal possibly at 600°C. The neutron-irradiated pressure vessel steels behave similarly to the high Cu samples, indicating that neutron irradiation induced precipitation occurs in these alloys as well. This work provides independent evidence for the irradiation-induced metallic precipitates seen by other techniques, gives evidence for the exact nature of the matrix damage, and is significant to understanding the in-service degradation of pressure vessel materials.

  14. Zr/ZrC modified layer formed on AISI 440B stainless steel by plasma Zr-alloying

    NASA Astrophysics Data System (ADS)

    Shen, H. H.; Liu, L.; Liu, X. Z.; Guo, Q.; Meng, T. X.; Wang, Z. X.; Yang, H. J.; Liu, X. P.

    2016-12-01

    The surface Zr/ZrC gradient alloying layer was prepared by double glow plasma surface alloying technique to increase the surface hardness and wear resistance of AISI 440B stainless steel. The microstructure of the Zr/ZrC alloying layer formed at different alloying temperatures and times as well as its formation mechanism were discussed by using scanning electron microscopy, glow discharge optical emission spectrum, X-ray diffraction and X-ray photoelectron spectroscopy. The adhesive strength, hardness and tribological property of the Zr/ZrC alloying layer were also evaluated in the paper. The alloying surface consists of the Zr-top layer and ZrC-subsurface layer which adheres strongly to the AISI 440B steel substrate. The thickness of the Zr/ZrC alloying layer increases gradually from 16 μm to 23 μm with alloying temperature elevated from 900 °C to 1000 °C. With alloying time from 0.5 h to 4 h, the alloyed depth increases from 3 μm to 30 μm, and the ZrC-rich alloyed thickness vs time is basically parabola at temperature of 1000 °C. Both the hardness and wear resistance of the Zr/ZrC alloying layer obviously increase compared with untreated AISI 440B steel.

  15. Effect of microstructure on the susceptibility of low-alloy steels to hydrogen attack

    SciTech Connect

    Williams, R.O.

    1981-08-01

    In an alloy steel in which one or more alloy additions stabilize the carbide phase, the carbon activity depends on the microstructure and the prior thermal history. The carbon activity is a major factor in the susceptibility of such steels to form internal methane bubbles when heated in high-pressure hydrogen. Thus one can expect to vary the susceptibility to hydrogen attack of a given steel by its prior treatment. The problem has two aspects. First, one needs to be able to calculate the equilibrium carbon activity when the steel is in internal equilibrium. A computer program in the appendix of this report takes care of part of this problem. When the thermodynamics of the mixed carbide phase is adequately modeled, then this problem can be solved. The second part is the rate of approach to equilibrium. An analysis of the rate of coarsening of carbides in such steels shows that this rate is enhanced by a fine carbide dispersion. Such a fine dispersion is also desirable for the maximum strength. Thus, we believe that under favorable circumstances the resistance to hydrogen attack can be enhanced by suitable thermal treatments of the steels used for the pressure vessels for hydrogen service. 12 figures.

  16. Lubricant Carriers for Drawing Alloyed and Unalloyed Steels,

    DTIC Science & Technology

    high C steels. It must be dissolved in hot water at 80 degrees. Additives such as wax or Na3PO4 increase the pliability of the layer of lubricant carrier. Addn. of glycerol increases the soly. of the salt.

  17. Fe-Zn Alloy Coating on Galvannealed (GA) Steel Sheet to Improve Product Qualities

    NASA Astrophysics Data System (ADS)

    Pradhan, Debabrata; Guin, Akshya Kumar; Raju, Pankaj; Manna, Manindra; Dutta, Monojit; Venugopalan, T.

    2014-09-01

    Galvannealed steel sheets (GA) have become the mainstream steel sheet for automobile applications because of their superior corrosion resistance, paintability, and weldability. To impart specific properties, different coatings on GA steel sheet were reported to improve properties further. In this context, we have developed an electroplating process (flash coating) for bright and adherent Fe-Zn alloy coating on GA steel sheet to enhance performances such as weldability, frictional behavior, phosphatability, and defect coverage. A comparative study with bare GA steel sheet was carried out for better elastration. The electroplating time was reduced below 10 s for practical applicability in an industrial coating line by modulating the bath composition. Electroplating was performed at current density of 200-500 A/m2 which yielded with higher cathode current efficiency of 85-95%. The performance results show that Fe-10 wt.% Zn-coated GA steel sheet (coating time 7 s) has better spot weldability, lower dynamic coefficient of friction (0.06-0.07 in lubrication), and better corrosion resistance compared to bare GA steel sheet. Uniform phosphate coating with globular crystal size of 2-5 µm was obtained on Fe-Zn flash-coated GA steel sheet. Hopeite was the main phosphate compound (77.9 wt.%) identified along with spencerite (13.6 wt.%) and phosphophyllite (8.5 wt.%).

  18. Oxidation behavior of Fe-20Cr steels alloyed with titanium at 1073 K

    NASA Astrophysics Data System (ADS)

    Setiawan, Asep Ridwan; Artono, Tri Juni

    2016-02-01

    In this work, the oxidation behavior of Fe-20 wt%Cr steels alloyed with different titanium contents: 0, 0.5, and 1 wt% are studied as a function of time in air atmosphere. The samples were isothermally oxidized at 1073 K for 86.4, 172.8, and 345.6 ks in a muffle furnace. The mass of specimen were recorded before and after oxidation. After the oxidation, phases in the oxide were identified by X-ray diffraction (XRD). Optical microscopy observation on the chromium base alloys show that the microstructure consist only ferritic phases. The addition of titanium in the Fe-20Cr alloys does not alter the microstructure significantly. The oxidation behavior of Fe-20Cr, Fe-20Cr-0.5Ti and Fe-20Cr-1Ti were followed the classical parabolic relationship with time. XRD analysis indicated that the oxide scales developed on the Fe-20Cr alloys surface during oxidation tests consisted mainly of Cr2O3. On the other hand, the oxide scales developed on the surface of Fe-20Cr-0.5Ti and Fe-20Cr-1Ti alloys comprised of Cr2O3 and TiO2 oxide. The formation of TiO2 oxide in the Ti-containing alloys consequently increases the mass gain of the alloys during oxidation compared to that of Fe-20Cr alloys.

  19. Tribological characteristics of aluminum alloys against steel lubricated by ammonium and imidazolium ionic liquids

    SciTech Connect

    Qu, Jun; Blau, Peter Julian; Dai, Sheng; Luo, Huimin; Meyer III, Harry M; Truhan, John J.

    2009-01-01

    Sliding friction and wear characteristics of aluminum alloys against AISI 52100 steel lubricated by ionic liquids (ILs) were investigated at both room and elevated temperatures. The tested aluminum alloys include a commercially pure aluminum Al 1100, a wrought alloy Al 6061-T6511, and a cast alloy Al 319-T6. The lubricating performance of two ILs with the same anion, one ammonium-based [C8H17]3NH.Tf2N and one imidazolium-based C10mim.Tf2N, were compared each other and benchmarked against that of a conventional fully-formulated engine oil. Significant friction (up to 35%) and wear (up to 55%) reductions were achieved by the ammonium IL when lubricating the three aluminum alloys compared to the engine oil. The imidazolium IL performed better than the oil but not as well as the ammonium IL for Al 1100 and 319 alloys. However, accelerated wear was unexpectedly observed for Al 6061 alloy when lubricated by C10mim.Tf2N. Surface chemical analyses implied complex tribochemical reactions between the aluminum surfaces and ILs during the wear testing, which has been demonstrated either beneficial by forming a protective boundary film or detrimental by causing severe tribo-corrosion. The effects of the IL cation structure, aluminum alloy composition, and tribo-testing condition on the friction and wear results have been discussed.

  20. Influence of nitrogen alloying on hydrogen embrittlement in AISI 304-type stainless steels

    NASA Astrophysics Data System (ADS)

    Hannula, Simo-Pekka; Hänninen, Hannu; Tähtinen, Seppo

    1984-12-01

    Hydrogen embrittlement of AISI 304-type austenitic stainless steels has been studied with special emphasis on the effects of the nitrogen content of the steels. Hydrogen charging was found to degrade the mechanical properties of all the steels studied, as measured by a tensile test. The fracture surfaces of hydrogen charged specimens were brittle cleavage-like whereas the uncharged specimens showed ductile, dimpled fracture. In sensitized materials transgranular cleavage mode of fracture was replaced by an intergranular mode of fracture and the losses of mechanical properties were higher. Nitrogen alloying decreased the hydrogen-induced losses of mechanical properties by increasing the stability of austenite. In sensitized steels the stability of austenite and nitrogen content were found to have only a minor effect on hydrogen embrittlement, except when sensitization had caused α'-martensite transformation at the grain boundaries.

  1. Effect of alloying elements on metadynamic recrystallization in HSLA steels

    NASA Astrophysics Data System (ADS)

    Roucoules, C.; Yue, S.; Jonas, J. J.

    1995-01-01

    By means of interrupted torsion tests, the kinetics of metadynamic recrystallization (MDRX) were studied in a Mo, a Nb, and a Ti microalloyed steel at temperatures ranging from 850 °C to 1000 °C and strain rates from 0.02 to 2 s1. Quenches were also performed after full MDRX. In contrast to the case of static recrystallization (SRX), the kinetics of MDRX are shown to be highly sensitive to a change of an order of magnitude in strain rate and are relatively insensitive to temperature changes within the range of values applicable to industrial hot-rolling practice. A similar algebraic dependence of the MDRX grain size on strain rate and temperature was found in the three steels. The kinetics of MDRX were slower in the Nb than in the Mo steel, and those of the Ti steel were slower than in the Nb and Mo steels. Above 900 °C and 950 °C, the retardation of MDRX in the Nb and Ti steels, respectively, is due to solute drag. Models predicting the start time for Nb and Ti carbonitride precipitation showed that MDRX is delayed below these temperatures by this mechanism. Comparison of the MDRX and precipitation start times in the Nb steel indicated that a temperature of “no-MDRX” could not be defined, in contrast to the well-defined T nr (no recrystallization temperature) of SRX. By means of torsion simulations composed of multiple interruptions, it is shown that MDRX is retarded decreasingly as the accumulated strain is increased. This appears to be due to the promotion of precipitate coarsening by the continuing deformation.

  2. Effect of alloy composition on high-temperature bending fatigue strength of ferritic stainless steels

    NASA Astrophysics Data System (ADS)

    Ahn, Yong-Sik; Song, Jeon-Young

    2011-12-01

    Exhaust manifolds are subjected to an environment in which heating and cooling cycles occur due to the running pattern of automotive engines. This temperature profile results in the repeated bending stress of exhaust pipes. Therefore, among high-temperature characteristics, the bending fatigue strength is an important factor that affects the lifespan of exhaust manifolds. Here, we report on the effect of the alloy composition, namely the weight fraction of the elements Cr, Mo, Nb, and Ti, on the high-temperature bending fatigue strength of the ferritic stainless steel used in exhaust manifolds. Little difference in the tensile strength and bending fatigue strength of the different composition steels was observed below 600 °C, with the exception of the low-Cr steel. However, steels with high Cr, Mo, or Nb fractions showed considerably larger bending fatigue strength at temperatures of 800 °C. After heating, the precipitates from the specimens were extracted electrolytically and analyzed using scanning electron microscopy energy dispersive spectrometry and transmission electron microscopy. Alloying with Cr and Mo was found to increase the bending fatigue strength due to the substitutional solid solution effect, while alloying with Nb enhanced the strength by forming fine intermetallic compounds, including NbC and Fe2Nb.

  3. Study on fatigue resistance of low alloy steels with Mo and Cr

    NASA Astrophysics Data System (ADS)

    Enculescu, E.; Chicet, D. L.; Dia, V.; Stanciu, S.

    2016-08-01

    This paper presents, based on a case study, the analysis of the factors that influence the mechanical cyclic fatigue resistance of two grades of low alloy steel with Mo and Cr. It was studied the fatigue behavior in real operating conditions of some active elements manufactured from the two low-alloyed steel grades, elements that are equipping some farm implements. Using the fractographic analysis, optical microscopy and scanning electron microscopy, were analyzed the samples that carried away because of the fatigue fracture. On samples taken from the two brands of low alloy steels with Mo and Cr were performed tempering thermal treatments that modified the structure, in order to improve the operating characteristics. The effect of those thermal treatments was initially observed by microstructural analysis of metallographic prepared samples (by polishing and chemical attack using nital reagent), that revealed a troostite type structure. On the heat-treated samples were determined a number of mechanical properties: hardness, impact strength and tensile test. There was observed an improvement of the impact bending strength for both alloys and a tensile behavior that favors increasing resistance to fatigue.

  4. Austenitic stainless steels and high strength copper alloys for fusion components

    NASA Astrophysics Data System (ADS)

    Rowcliffe, A. F.; Zinkle, S. J.; Stubbins, J. F.; Edwards, D. J.; Alexander, D. J.

    1998-10-01

    An austenitic stainless steel (316LN), an oxide-dispersion-strengthened copper alloy (GlidCop Al25), and a precipitation-hardened copper alloy (Cu-Cr-Zr) are the primary structural materials for the ITER first wall/blanket and divertor systems. While there is a long experience of operating 316LN stainless steel in nuclear environments, there is no prior experience with the copper alloys in neutron environments. The ITER first wall (FW) consists of a stainless steel shield with a copper alloy heat sink bonded by hot isostatic pressing (HIP). The introduction of bi-layer structural material represents a new materials engineering challenge; the behavior of the bi-layer is determined by the properties of the individual components and by the nature of the bond interface. The development of the radiation damage microstructure in both classes of materials is summarized and the effects of radiation on deformation and fracture behavior are considered. The initial data on the mechanical testing of bi-layers indicate that the effectiveness of GlidCop Al25 as a FW heat sink material is compromised by its strongly anisotropic fracture toughness and poor resistance to crack growth in a direction parallel to the bi-layer interface.

  5. 76 FR 49437 - Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Preliminary Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-10

    ... International Trade Administration Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Preliminary Results of Antidumping Duty Administrative Review AGENCY: Import Administration, International Trade..., 2011. FOR FURTHER INFORMATION CONTACT: Mark Flessner or Robert James, AD/CVD Operations, Office...

  6. 75 FR 78216 - Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Preliminary Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-15

    ... International Trade Administration Certain Circular Welded Non-Alloy Steel Pipe From Mexico: Preliminary Results of Antidumping Duty Administrative Review AGENCY: Import Administration, International Trade...: December 15, 2010. FOR FURTHER INFORMATION CONTACT: Mark Flessner or Robert James, AD/CVD...

  7. 75 FR 34980 - Circular Welded Non-Alloy Steel Pipe from the Republic of Korea: Final Results of the Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-21

    ... Welded Non-Alloy Steel Pipe and Tube From Brazil, the Republic of Korea, Mexico, and Venezuela, 61 FR... from Brazil, the Republic of Korea, Mexico, and Venezuela, and Amendment to Final Determination...

  8. Corrosion of ferritic-martensitic steels and nickel-based alloys in supercritical water

    NASA Astrophysics Data System (ADS)

    Ren, Xiaowei

    The corrosion behavior of ferritic/martensitic (F/M) steels and Ni-based alloys in supercritical water (SCW) has been studied due to their potential applications in future nuclear reactor systems, fossil fuel power plants and waste treatment processes. 9˜12% chromium ferritic/martensitic steels exhibit good radiation resistance and stress corrosion cracking resistance. Ni-based alloys with an austenitic face-centered cubic (FCC) structure are designed to retain good mechanical strength and corrosion/oxidation resistance at elevated temperatures. Corrosion tests were carried out at three temperatures, 360°C, 500°C and 600°C, with two dissolved oxygen contents, 25 ppb and 2 ppm for up to 3000 hours. Alloys modified by grain refinement and reactive element addition were also investigated to determine their ability to improve the corrosion resistance in SCW. A duplex oxide structure was observed in the F/M steels after exposure to 25 ppb oxygen SCW, including an outer oxide layer with columnar magnetite grains and an inner oxide layer constituted of a mixture of spinel and ferrite phases in an equiaxed grain structure. An additional outermost hematite layer formed in the SCW-exposed samples when the oxygen content was increased to 2 ppm. Weight gain in the F/M steels increased with exposure temperatures and times, and followed parabolic growth kinetics in most of the samples. In Ni-based alloys after exposure to SCW, general corrosion and pitting corrosion were observed, and intergranular corrosion was found when exposed at 600°C due to formation of a local healing layer. The general oxide structure on the Ni-based alloys was characterized as NiO/Spinel/(CrxFe 1-x)2O3/(Fe,Ni). No change in oxidation mechanism was observed in crossing the critical point despite the large change in water properties. Corrosion resistance of the F/M steels was significantly improved by plasma-based yttrium surface treatment because of restrained outward diffusion of iron by the

  9. Braze alloy process and strength characterization studies for 18 nickel grade 200 maraging steel with application to wind tunnel models

    NASA Technical Reports Server (NTRS)

    Bradshaw, James F.; Sandefur, Paul G., Jr.; Young, Clarence P., Jr.

    1991-01-01

    A comprehensive study of braze alloy selection process and strength characterization with application to wind tunnel models is presented. The applications for this study include the installation of stainless steel pressure tubing in model airfoil sections make of 18 Ni 200 grade maraging steel and the joining of wing structural components by brazing. Acceptable braze alloys for these applications are identified along with process, thermal braze cycle data, and thermal management procedures. Shear specimens are used to evaluate comparative shear strength properties for the various alloys at both room and cryogenic (-300 F) temperatures and include the effects of electroless nickel plating. Nickel plating was found to significantly enhance both the wetability and strength properties for the various braze alloys studied. The data are provided for use in selecting braze alloys for use with 18 Ni grade 200 steel in the design of wind tunnel models to be tested in an ambient or cryogenic environment.

  10. Study of Effects of Alloying and Heat Treatment on Hydrogen Enbrittlement Susceptibility of Electroslag Remelted 4340 Steel.

    DTIC Science & Technology

    1986-10-01

    toughness data ....... 45 A.5 Example of instrumented impact data ...... 46 iX TECHNICAL REPORT 1.0 INTRODUCTION Ballistically resistant advanced...Conventional alloys steels of ESR 4340 (baseline), ESR 4340M or ESR 300M , and the new ESR HP310 alloy steels, respectively, were used to represent this...method uses the rapid, inexpensive, modular (RIM) SCC-testing system. Only a maximum of five Charpy -Sized specimens are required to obtain

  11. Experimental and analytical investigation of the seizure process in aluminum-silicon alloy/steel tribocontacts

    NASA Astrophysics Data System (ADS)

    He, Xiaozhou

    1998-12-01

    This research is an experimental and analytical investigation of the scuffing/seizure mechanism in Al-Si alloy/steel tribocontacts. An analytical model is developed based on analyses and experiments to predict scuffing/seizure failure in Al-Si alloy/steel tribocontacts, which can be applied to tribo-components in engines, refrigerators and air conditioners. The wear and scuffing/seizure experiments have been conducted through a block-on-ring tester for 339 and ESE-M2A137 Al-Si alloys under the dry and boundary lubrication conditions. The experimental research consists of: (a) wear debris generation and EDX analysis, (b) wear surface morphological analysis, (c) scuffing/seizure mechanism and process analysis, (d) scuffing/seizure PV curves under the dry contact and boundary lubrication, and (e) effects of several main factors on scuffing/seizure. The analytical research includes the following: (a) the investigation of the scuffing/seizure mechanisms in the Al-Si alloy/steel tribocontacts, (b) 3-D asperity contact pressures for longitudinal, transverse and isotropic surface roughness profiles, (c) 3-D surface asperity contact temperature rise due to the friction, (d) failure analyses of the various lubricating films, (e) analyses of the temperature dependence of surface tangential traction and shear strength in a surface layer of Al-Si alloy, (f) the scuffing/seizure failure analytical model under dry contact and boundary lubrication. The analytical model is based on the new hypothesis of three defense lines against scuffing/seizure failure: the adsorbed oil film, oxide film and the ratio of surface tangential traction with the shear strength in a surface layer. These two films together with a surface layer itself form three defense lines against scuffing/seizure. The surface tangential traction exceeds the bulk shear strength in a surface layer of Al-Si alloy is the necessary and sufficient condition for the scuffing/seizure occurrence. The analytical model has a

  12. Hydrogen induced cracking tests of high strength steels and nickel-iron base alloys using the bolt-loaded specimen

    SciTech Connect

    Vigilante, G.N.; Underwood, J.H.; Crayon, D.; Tauscher, S.; Sage, T.; Troiano, E.

    1997-12-31

    Hydrogen induced cracking tests were conducted on high strength steels and nickel-iron base alloys using the constant displacement bolt-loaded compact specimen. The bolt-loaded specimen was subjected to both acid and electrochemical cell environments in order to produce hydrogen. The materials tested were A723, Maraging 200, PH 13-8 Mo, Alloy 718, Alloy 706, and A286, and ranged in yield strength from 760--1400 MPa. The effects of chemical composition, refinement, heat treatment, and strength on hydrogen induced crack growth rates and thresholds were examined. In general, all high strength steels tested exhibited similar crack growth rates and thresholds were examined. In general, all high strength steels tested exhibited similar crack growth rates and threshold levels. In comparison, the nickel-iron base alloys tested exhibited up to three orders of magnitude lower crack growth rates than the high strength steels tested. It is widely known that high strength steels and nickel base alloys exhibit different crack growth rates, in part, because of their different crystal cell structure. In the high strength steels tested, refinement and heat treatment had some effect on hydrogen induced cracking, though strength was the predominant factor influencing susceptibility to cracking. When the yield strength of one of the high strength steels tested was increased moderately, from 1130 MPa to 1275 MPa, the incubation times decreased by over two orders of magnitude, the crack growth rates increased by an order of magnitude, and the threshold stress intensity was slightly lower.

  13. Understanding and Laboratory Prediction of the Atmospheric Corrosion behavior of Steels and of Non-Ferrous Metals and Alloys.

    DTIC Science & Technology

    1984-01-31

    or Aluzinc ), aluminum-manganese, aluminum-copper-magnesium and aluminum-copper-magnesium-zinc alloys. The method * gave significant results: for...galvanized steel and galvalume ( aluzinc )- coated steel. During the second semi-annual period, fully elaborated tests were conducted on the three aluminum

  14. Factors affecting the strength of multipass low-alloy steel weld metal

    NASA Technical Reports Server (NTRS)

    Krantz, B. M.

    1972-01-01

    The mechanical properties of multipass high-strength steel weld metals depend upon several factors, among the most important being: (1) The interaction between the alloy composition and weld metal cooling rate which determines the as-deposited microstructure; and (2) the thermal effects of subsequent passes on each underlying pass which alter the original microstructure. The bulk properties of a multipass weld are therefore governed by both the initial microstructure of each weld pass and its subsequent thermal history. Data obtained for a high strength low alloy steel weld metal confirmed that a simple correlation exists between mechanical properties and welding conditions if the latter are in turn correlated as weld cooling rate.

  15. Oxidation and corrosion behavior of modified-composition, low-chromium 304 stainless steel alloys

    NASA Technical Reports Server (NTRS)

    Stephens, J. R.; Barrett, C. A.

    1977-01-01

    The effects of substituting less strategic elements than Cr on the oxidation and corrosion resistance of AISI 304 stainless steel were investigated. Cyclic oxidation resistance was evaluated at 870 C. Corrosion resistance was determined by exposure of specimens to a boiling copper-rich solution of copper sulfate and sulfuric acid. Alloy substitutes for Cr included Al, Mn, Mo, Si, Ti, V, Y, and misch metal. A level of about 12% Cr was the minimum amount of Cr required for adequate oxidation and corrosion resistance in the modified composition 304 stainless steels. This represents a Cr saving of at least 33%. Two alloys containing 12% Cr and 2% Al plus 2% Mo and 12% Cr plus 2.65% Si were identified as most promising for more detailed evaluation.

  16. Effect of welding process on the microstructure and properties of dissimilar weld joints between low alloy steel and duplex stainless steel

    NASA Astrophysics Data System (ADS)

    Wang, Jing; Lu, Min-xu; Zhang, Lei; Chang, Wei; Xu, Li-ning; Hu, Li-hua

    2012-06-01

    To obtain high-quality dissimilar weld joints, the processes of metal inert gas (MIG) welding and tungsten inert gas (TIG) welding for duplex stainless steel (DSS) and low alloy steel were compared in this paper. The microstructure and corrosion morphology of dissimilar weld joints were observed by scanning electron microscopy (SEM); the chemical compositions in different zones were detected by energy-dispersive spectroscopy (EDS); the mechanical properties were measured by microhardness test, tensile test, and impact test; the corrosion behavior was evaluated by polarization curves. Obvious concentration gradients of Ni and Cr exist between the fusion boundary and the type II boundary, where the hardness is much higher. The impact toughness of weld metal by MIG welding is higher than that by TIG welding. The corrosion current density of TIG weld metal is higher than that of MIG weld metal in a 3.5wt% NaCl solution. Galvanic corrosion happens between low alloy steel and weld metal, revealing the weakness of low alloy steel in industrial service. The quality of joints produced by MIG welding is better than that by TIG welding in mechanical performance and corrosion resistance. MIG welding with the filler metal ER2009 is the suitable welding process for dissimilar metals jointing between UNS S31803 duplex stainless steel and low alloy steel in practical application.

  17. The development of ultrahigh strength low alloy cast steels with increased toughness

    NASA Astrophysics Data System (ADS)

    Lynch, Paul C.

    This work describes the initial work on the development of the next generation of ultrahigh strength low alloy (UHSLA) cast steels. These UHSLA cast steels have both ultrahigh strength levels and good impact toughness. The influence of heat treatment, secondary processing using hot isostatic processing (HIP), and chemical composition on the microstructure and properties of UHSLA cast steels have been evaluated. The extent of microsegregation reduction expected during the heat treatment of UHSLA cast steels has also been estimated by diffusion modeling. This new family of UHSLA cast steels is similar in composition and properties to UHSLA wrought steels. However, the heat treatment and secondary processing of the UHSLA cast steels is used to develop microstructures and properties typically developed through thermomechanical processing and heat treatment for wrought UHSLA steels. Two martensitic UHSLA steels, 4340+ (silicon modified 4340) and ES-1 were investigated for this study. For the 4340+ alloy, heat treatment variables evaluated include homogenization temperature and time, tempering temperature, and austempering temperature and time. For the ES-1 alloy, heat treatment variables evaluated include homogenization temperature and time, austenization temperature, cryogenic treatment, and tempering temperature. The effect of high temperature hot isostatic processing (HIP) on the 4340+ and ES- 1 alloys was also investigated. Tensile properties, charpy v-notch impact toughness (CVN), microstructures, and fractographs have all been characterized after heat treatment. The effects of HIP on microporosity reduction in the ES-1 alloy were also investigated. The experiments carried out on the investment cast 4340+ alloy have shown that increasing the homogenization temperature can increase CVN without changing the ultimate tensile strength (UTS) or yield strength (YS) of the cast material. By replacing the homogenization step in the conventional heat treatment process with

  18. Alloying effect of copper on the corrosion properties of low-alloy steel for flue gas desulfurization system

    NASA Astrophysics Data System (ADS)

    Kim, Seon-Hong; Park, Sun-Ah; Kim, Jung-Gu; Shin, Kee-Sam; He, Yinsheng

    2015-03-01

    The alloying effect of Cu for a flue gas desulfurization materials was investigated using the electrochemical methods in the modified green death solution and the surface analyses. The test results demonstrated that the densely formed rust layer with high metallic Cu content improves the corrosion resistance of Cu-containing steel in the flue gas desulfurization (FGD) environment. The rust layer on the surface of the 0.02 wt% Cu steel, which has an insufficient Cu content, was less protective than others. The 0.05 wt% Cu steel represented the highest corrosion resistance due to the formation of the densely formed rust layer with optimum Cu content. Because the free standing Cu2S precipitates had the insoluble characteristic in highly acidic solution, it produced the relatively porous Cu-enriched layer on the 0.08 wt% Cu steel surface. From these phenomena, the corrosion resistance of specimen decreased as the Cu content of specimen increased from 0.05 wt% to 0.08 wt%.

  19. Effects of alloying on aging and hardening processes of steel with 20% nickel

    NASA Technical Reports Server (NTRS)

    Bogachev, I. N.; Zvigintsev, N. V.; Maslakova, T. M.

    1981-01-01

    Measurements of hardness, thermal emf, and electrical resistance were used to study the effects of Co, Mo, Ti and Al contents on aging and hardening processes in Fe 20%Ni steel. It is shown that the effects of these alloying elements differ substantially. Anomalies which arise in the temperature dependence of physical properties due to the presence of cobalt and molybdenum are reduced by the inclusion of titanium and aluminum (and vice versa).

  20. Electrochemical Corrosion Testing of Borated Stainless Steel Alloys

    SciTech Connect

    lister, tedd e; Mizia, Ronald E

    2007-05-01

    The Department of Energy Office of Civilian Radioactive Waste Management has specified borated stainless steel manufactured to the requirements of ASTM A 887-89, Grade A, UNS S30464, to be the material used for the fabrication of the fuel basket internals of the preliminary transportation, aging, and disposal canister system preliminary design. The long-term corrosion resistance performance of this class of borated materials must be verified when exposed to expected YMP repository conditions after a waste package breach. Electrochemical corrosion tests were performed on crevice corrosion coupons of Type 304 B4 and Type 304 B5 borated stainless steels exposed to single postulated in-package chemistry at 60°C. The results show low corrosion rates for the test period

  1. Electrochemical Corrosion Testing of Borated Stainless Steel Alloys

    SciTech Connect

    lister, tedd e; Mizia, Ronald E

    2007-09-01

    The Department of Energy Office of Civilian Radioactive Waste Management has specified borated stainless steel manufactured to the requirements of ASTM A 887-89, Grade A, UNS S30464, to be the material used for the fabrication of the fuel basket internals of the preliminary transportation, aging, and disposal canister system preliminary design. The long-term corrosion resistance performance of this class of borated materials must be verified when exposed to expected YMP repository conditions after a waste package breach. Electrochemical corrosion tests were performed on crevice corrosion coupons of Type 304 B4 and Type 304 B5 borated stainless steels exposed to single postulated in-package chemistry at 60°C. The results show low corrosion rates for the test period

  2. Formation Energies and Electronic Properties of Vanadium Carbides Found in High Strength Steel Alloys

    NASA Astrophysics Data System (ADS)

    Limmer, Krista; Medvedeva, Julia

    2013-03-01

    Carbide formation and stabilization in steels is of great interest owing to its effect on the microstructure and properties of the Fe-based alloys. The appearance of carbides with different metal/C ratios strongly depends on the carbon concentration, alloy composition as well as the heat treatment. Strong carbide-forming elements such as Ti, V, and Nb have been used in microalloyed steels; with VC showing an increased solubility in the iron matrix as compared with TiC and NbC. This allows for dissolution of the VC into the steel during heating and fine precipitation during cooling. In addition to VC, the primary vanadium carbide with cubic structure, a wide range of non-stoichiometric compositions VCy with y varying from 0.72 to 0.88, has been observed. This range includes two ordered compounds, V8C7 and V6C5. In this study, first-principles density functional theory (DFT) is employed to examine the stability of the binary carbides by calculating their formation energies. We compare the local structures (atomic coordination, bond distances and angles) and the density of states in optimized geometries of the carbides. Further, the effect of alloying additions, such as niobium and titanium, on the carbide stabilization is investigated. We determine the energetically preferable substitutional atom location in each carbide and study the impurity distribution as well as its role in the carbide formation energy and electronic structure.

  3. Precipitation in Microalloyed Steel by Model Alloy Experiments and Thermodynamic Calculations

    NASA Astrophysics Data System (ADS)

    Frisk, Karin; Borggren, Ulrika

    2016-10-01

    Precipitation in microalloyed steel has been studied by applying thermodynamic calculations based on a description of the Gibbs energies of the individual phases over the full multicomponent composition range. To validate and improve the thermodynamic description, new experimental investigations of the phase separation in the cubic carbides/nitrides/carbonitrides in alloys containing Nb, V, Mo, and Cr, have been performed. Model alloys were designed to obtain equilibrium carbides/carbonitrides that are sufficiently large for measurements of compositions, making it possible to study the partitioning of the elements into different precipitates, showing distinctly different composition sets. The reliability of the calculations, when applied to multicomponent alloys, was tested by comparing with published experimental studies of precipitation in microalloyed steel. It is shown that thermodynamic calculations accurately describe the observed precipitation sequences. Further, they can reproduce several important features of precipitation processes in microalloyed steel such as the partitioning of Mo between matrix and precipitates and the variation of precipitate compositions depending on precipitation temperature.

  4. Cryo-quenched Fe-Ni-Cr alloy single crystals: A new decorative steel

    DOE PAGES

    Boatner, Lynn A.; Kolopus, James A.; Lavrik, Nicolay V.; ...

    2016-08-31

    In this paper, a decorative steel is described that is formed by a process that is unlike that of the fabrication methods utilized in making the original Damascus steels over 2000 years ago. The decorative aspect of the steel arises from a three-dimensional surface pattern that results from cryogenically quenching polished austenitic alloy single crystals into the martensitic phase that is present below 190 K. No forging operations are involved – the mechanism is entirely based on the metallurgical phase properties of the ternary alloy. The symmetry of the decorative pattern is determined and controlled by the crystallographic orientation andmore » symmetry of the 70%Fe,15%Ni,15%Cr alloy single crystals. Finally, in addition to using “cuts” made along principal crystallographic surface directions, an effectively infinite number of other random-orientation “cuts” can be utilized to produce decorative patterns where each pattern is unique after the austenitic-to-martensitic phase transformation.« less

  5. Effect of Cr content on the corrosion performance of low-Cr alloy steel in a CO2 environment

    NASA Astrophysics Data System (ADS)

    Xu, Lining; Wang, Bei; Zhu, Jinyang; Li, Wei; Zheng, Ziyi

    2016-08-01

    Low-Cr alloy steel demonstrates lower corrosion rate than does C steel in a high-temperature and high-pressure CO2-containing environment. This study aimed to clarify the role of the Cr content in mitigating corrosion and reports the performance of 1%Cr, 2%Cr, 3%Cr, 4%Cr, 5%Cr, and 6.5%Cr steels. The results show that low-Cr alloy steel in CO2 at 80 °C and 0.8 MPa possesses spontaneous prepassivation characteristics when the Cr content is 3% or higher. Furthermore, the formation and peel-off of a prepassivation film on 3%Cr-6.5%Cr steels surfaces during polarization demonstrate that adequate amount of Cr in the steel substrate can cause protective layer. The main component of prepassivation film on 3%Cr steel is Cr(OH)3. Thus, the role of Cr is revealed. An adequate amount of Cr in the steel substrate causes the formation of protective Cr(OH)3 layer, which helps low-Cr steel to possess prepassivation characteristics. Prepassivation is the reason why low-Cr steel has a lower corrosion rate than C steel.

  6. Effects of solute elements on irradiation hardening and microstructural evolution in low alloy steels

    NASA Astrophysics Data System (ADS)

    Fujii, Katsuhiko; Ohkubo, Tadakatsu; Fukuya, Koji

    2011-10-01

    The effects of the elements Mn, Ni, Si and Cu on irradiation hardening and microstructural evolution in low alloy steels were investigated in ion irradiation experiments using five kinds of alloys prepared by removing Mn, Ni and Si from, and adding 0.05 wt.%Cu to, the base alloy (Fe-1.5Mn-0.5Ni-0.25Si). The alloy without Mn showed less hardening and the alloys without Ni or Si showed more hardening. The addition of Cu had hardly any influence on hardening. These facts indicated that Mn enhanced hardening and that Ni and Si had some synergetic effects. The formation of solute clusters was not confirmed by atom probe (AP) analysis, whereas small dislocation loops were identified by TEM observation. The difference in hardening between the alloys with and without Mn was qualitatively consistent with loop formation. However, microstructural components that were not detected by the AP and TEM were assumed to explain the hardening level quantitatively.

  7. Alloy 31, a new 6 moly stainless steel with improved corrosion resistance in seawater

    SciTech Connect

    Jasner, M.; Heubner, U.

    1995-10-01

    Alloy 31--UNS N08031--31Ni-27Cr-6.5Mo-1.2Cu-0.2N-balance iron--is an advanced 6 Mo stainless steel with increased chromium and nickel, contents for seawater service. In hot seawater the pitting potential of alloy 31 remains high up to 90 C (194 F). Investigations of resistance to crevice corrosion in real piping systems in natural seawater, both North Sea and Baltic Sea, show that the threshold conditions for alloy 31 in chlorinated seawater (North Sea) are at 40 C and 1 ppm chlorine well superior to the 6 Mo stainless grades being currently in use. In addition, alloy 31 shows an excellent resistance to corrosion versus both hot reducing media (e.g. H{sub 2}SO{sub 4}) and hot oxidizing media (e.g. HNO{sub 3}). The combination of high resistance to localized corrosion vs. hot chloride-bearing cooling waters including seawater and aggressive oxidizing and reducing hot corrosive media is a unique feature of alloy 31. Alloy 31 is recommended for the construction of heat exchangers, process coolers and piping systems. The material is supplied in a number of semifinished products such as seamless and welded pipes, fittings, flanges, forged bars, plate, sheet, strip, wire and prefabricated piping systems.

  8. Orientation Dependence of Cracking in Hot-Dip Zn-Al-Mg Alloy Coatings on a Sheet Steel

    NASA Astrophysics Data System (ADS)

    Park, Y. B.; Kim, I. G.; Kim, S. G.; Kim, W. T.; Kim, T. C.; Oh, M. S.; Kim, J. S.

    2017-01-01

    The present study was aimed at investigating a basic cause of cracking in hot-dip Zn-Al-Mg alloy coatings on an extra deep drawing quality sheet steel. The electron backscattering diffraction technique was employed to examine the crystallographic planes of the cracks generated before and after bending deformation of the coated steel sheets. It was clarified that the occurrence of cracking in the Zn-Al-Mg alloy coatings absolutely depends on the orientation of the primary Zn and eutectic Zn alloy phases. Finally, a cracking mechanism was proposed on the basis of the anisotropy of thermal expansion and the Young's modulus in the phases constituting the coatings.

  9. Orientation Dependence of Cracking in Hot-Dip Zn-Al-Mg Alloy Coatings on a Sheet Steel

    NASA Astrophysics Data System (ADS)

    Park, Y. B.; Kim, I. G.; Kim, S. G.; Kim, W. T.; Kim, T. C.; Oh, M. S.; Kim, J. S.

    2017-03-01

    The present study was aimed at investigating a basic cause of cracking in hot-dip Zn-Al-Mg alloy coatings on an extra deep drawing quality sheet steel. The electron backscattering diffraction technique was employed to examine the crystallographic planes of the cracks generated before and after bending deformation of the coated steel sheets. It was clarified that the occurrence of cracking in the Zn-Al-Mg alloy coatings absolutely depends on the orientation of the primary Zn and eutectic Zn alloy phases. Finally, a cracking mechanism was proposed on the basis of the anisotropy of thermal expansion and the Young's modulus in the phases constituting the coatings.

  10. Secondary hardening and fracture behavior in alloy steels containing Mo, W, and Cr

    NASA Astrophysics Data System (ADS)

    Kwon, H.; Lee, K. B.; Yang, H. R.; Lee, J. B.; Kim, Y. S.

    1997-03-01

    In 4Mo, 6W, 2Mo3W, 2Mo2Cr, and 3W2Cr alloy steels, which cointain alloying elements, such as Mo, W and Cr, contributing to the secondary hardening by forming M2C type carbide, the secondary hardening and fracture behavior were studied. Molybdenum had a strong effect on secondary hardening, while W had a very weak effect on it but delayed the overaging. The MoW steel exhibited both moderately strong hardening and considerable resistance to overaging. On the other hand, the secondary hardening effect was diminished by the Cr addition, because the cementite of M3C type was stabilized at higher temperatures and the formation of M2C carbides was thus inhibited. Although the Cr addition had no merit in the secondary hardening itself, it eliminated the secondary hardening embrittlement (SHE). This was observed as a severe intergranular embrittlement due to the impurity segregation for the Mo and MoW steels and as a decrease in upper shelf energy for W steel, even in the overaged condition.

  11. Cr-Al coatings on low carbon steel prepared by a mechanical alloying technique

    NASA Astrophysics Data System (ADS)

    Hia, A. I. J.; Sudiro, T.; Aryanto, D.; Sebayang, K.

    2016-08-01

    Four different compositions of Cr and Al coatings as Cr10o, Cr87.5Al12.5, Cr5oAl5o, and Al100 have been prepared on the surface of low carbon steel by a mechanical alloying technique. The composition of each powder was milled for 2 hour in a stainless steel crucible with a ball to powder ratio of 10:1. Hereafter, the Cr-Al powder and substrate were mechanical alloyed in air for 1 hour. Heat treatment of coated sample were carried out at 800°C in a vacuum furnace. In order to characterize the phase composition and microstructure of the coating before and after heat treatment, XRD and SEM-EDX were used. The results show that Cr, Cr-Al or Al coatings were formed on the surface of low carbon steel. After heat treatment, new phases and interdiffusion zone were formed in the coating and at the coating/steel interface, depending on the coating composition.

  12. Microstructure-fracture toughness relationship of vanadium alloy/stainless steel brazed joints

    NASA Astrophysics Data System (ADS)

    Gan, Y. X.; Aglan, H. A.; Steward, R. V.; Chin, B. A.; Grossbeck, M. L.

    2001-11-01

    In this work, brazing V-5Ti-5Cr to 304 stainless steel (SS 304) using Au-18Ni alloy as filler material was conducted under high vacuum condition. Sessile drop technique was used to determine the wettability of filler alloy to the stainless steel and the vanadium alloy substrates upon which the relationship between the contact angles with time was obtained. Tensile tests were performed on unnotched and notched specimens to demonstrate the overloading behavior and the fracture toughness of the base materials and the brazed joint. Fracture surface was examined for both the V-5Ti-5Cr and the joint to identify the failure mechanisms under static loadings. It was found that the Au-18Ni filler material exhibited good wettability with the SS 304 and V-5Ti-5Cr. The ultimate tensile strength of the brazed joint reached 245 MPa. The strain to failure was about 1.3%. Young's modulus was about 351 GPa. The fracture toughness ( KIc) of this joint was 19.1 MPa √ m. The fracture surface of the joint showed well brazed area with good wettability and proper amount of residual filler material which came from the solidification of residual liquid filler alloy of Au-Ni. The failure of the joint occurred along the interface of the vanadium/filler under static load.

  13. Alloying effect of Ni and Cr on irradiated microstructural evolution of type 304 stainless steels

    NASA Astrophysics Data System (ADS)

    Tan, L.; Busby, J. T.

    2013-11-01

    Life extension of the existing nuclear power plants imposes significant challenges to core structural materials that suffer increased fluences. This paper presents the microstructural evolution of a type 304 stainless steel and its variants alloyed with extra Ni and Cr under neutron irradiation at ˜320 °C for up to 10.2 dpa. Similar to the reported data of type 304 variants, a large amount of Frank loops, ultrafine G-phase/M23C6 particles, and limited amount of cavities were observed in the irradiated samples. The irradiation promoted the growth of pre-existing M23C6 at grain boundaries and resulted in some phase transformation to CrC in the alloy with both extra Ni and Cr. A new type of ultrafine precipitates, possibly (Ti,Cr)N, was observed in all the samples, and its amount was increased by the irradiation. Additionally, α-ferrite was observed in the type 304 steel but not in the Ni or Ni + Cr alloyed variants. The effect of Ni and Cr alloying on the microstructural evolution is discussed.

  14. Laser alloying of bearing steel with boron and self-lubricating addition

    NASA Astrophysics Data System (ADS)

    Kotkowiak, Mateusz; Piasecki, Adam; Kulka, Michał

    2016-12-01

    100CrMnSi6-4 bearing steel has been widely used for many applications, e.g. rolling bearings which work in difficult operating conditions. Therefore, this steel has to be characterized by special properties such as high wear resistance and high hardness. In this study laser-boriding was applied to improve these properties. Laser alloying was conducted as the two step process with two different types of alloying material: amorphous boron only and amorphous boron with addition of calcium fluoride CaF2. At first, the surface was coated with paste including alloying material. Second step of the process consisted in laser re-melting. The surface of sample, coated with the paste, was irradiated by the laser beam. In this study, TRUMPF TLF 2600 Turbo CO2 laser was used. The microstructure, microhardness and wear resistance of both laser-borided layer and laser-borided layer with the addition of calcium fluoride were investigated. The layer, alloyed with boron and CaF2, was characterized by higher wear resistance than the layer after laser boriding only.

  15. ATR-A1 irradiation experiment on vanadium alloys and low activation steels

    SciTech Connect

    Tasi, H.; Strain, R.V.; Gomes, I.; Hins, A.G.; Smith, D.L.

    1996-04-01

    To study the mechanical properties of vanadium alloys under neutron irradiation at low temperatures, an experiment was designed and constructed for irradiation in the Advanced Test Reactor (ATR). The experiment contained Charpy, tensile, compact tension, TEM, and creep specimens of vanadium alloys. It also contained limited low-activation ferritic steel specimens as part of the collaborative agreement with Monbusho of Japan. The design irradiation temperatures for the vanadium alloy specimens in the experiment are {approx}200 and 300{degrees}C, achieved with passive gap-gap sizing and fill gas blending. To mitigate vanadium-to-chromium transmutation from the thermal neutron flux, the test specimens are contained inside gadolinium flux filters. All specimens are lithium-bonded. The irradiation started in Cycle 108A (December 3, 1995) and is expected to have a duration of three ATR cycles and a peak influence of 4.4 dpa.

  16. Simultaneous material flow analysis of nickel, chromium, and molybdenum used in alloy steel by means of input-output analysis.

    PubMed

    Nakajima, Kenichi; Ohno, Hajime; Kondo, Yasushi; Matsubae, Kazuyo; Takeda, Osamu; Miki, Takahiro; Nakamura, Shinichiro; Nagasaka, Tetsuya

    2013-05-07

    Steel is not elemental iron but rather a group of iron-based alloys containing many elements, especially chromium, nickel, and molybdenum. Steel recycling is expected to promote efficient resource use. However, open-loop recycling of steel could result in quality loss of nickel and molybdenum and/or material loss of chromium. Knowledge about alloying element substance flow is needed to avoid such losses. Material flow analyses (MFAs) indicate the importance of steel recycling to recovery of alloying elements. Flows of nickel, chromium, and molybdenum are interconnected, but MFAs have paid little attention to the interconnected flow of materials/substances in supply chains. This study combined a waste input-output material flow model and physical unit input-output analysis to perform a simultaneous MFA for nickel, chromium, and molybdenum in the Japanese economy in 2000. Results indicated the importance of recovery of these elements in recycling policies for end-of-life (EoL) vehicles and constructions. Improvement in EoL sorting technologies and implementation of designs for recycling/disassembly at the manufacturing phase are needed. Possible solutions include development of sorting processes for steel scrap and introduction of easier methods for identifying the composition of secondary resources. Recovery of steel scrap with a high alloy content will reduce primary inputs of alloying elements and contribute to more efficient resource use.

  17. Liquid metal embrittlement susceptibility of ferritic martensitic steel in liquid lead alloys

    NASA Astrophysics Data System (ADS)

    Van den Bosch, J.; Bosch, R. W.; Sapundjiev, D.; Almazouzi, A.

    2008-06-01

    The susceptibility of the ferritic-martensitic steels T91 and EUROFER97 to liquid metal embrittlement (LME) in lead alloys has been examined under various conditions. T91, which is currently the most promising candidate material for the high temperature components of the future accelerator driven system (ADS) was tested in liquid lead bismuth eutectic (LBE), whereas the reduced activation steel, EUROFER97 which is under consideration to be the structural steel for fusion reactors was tested in liquid lead lithium eutectic. These steels, similar in microstructure and mechanical properties in the unirradiated condition were tested for their susceptibility to LME as function of temperature (150-450 °C) and strain rate (1 × 10 -3-1 × 10 -6 s -1). Also, the influence of pre-exposure and surface stress concentrators was evaluated for both steels in, respectively, liquid PbBi and PbLi environment. To assess the LME effect, results of the tests in liquid metal environment are compared with tests in air or inert gas environment. Although both unirradiated and irradiated smooth ferritic-martensitic steels do not show any or little deterioration of mechanical properties in liquid lead alloy environment compared to their mechanical properties in gas as function of temperature and strain rate, pre-exposure or the presence of surface stress concentrators does lead to a significant decrease in total elongation for certain test conditions depending on the type of liquid metal environment. The results are discussed in terms of wetting enhanced by liquid metal corrosion or crack initiation processes.

  18. Wear Evaluation of AISI 4140 Alloy Steel with WC/C Lamellar Coatings Sliding Against EN 8 Using Taguchi Method

    NASA Astrophysics Data System (ADS)

    Kadam, Nikhil Rajendra; Karthikeyan, Ganesarethinam

    2016-10-01

    The purpose of the experiments in this paper is to use the Taguchi methods to investigate the wear of WC/C coated nitrided AISI 4140 alloy steel. A study of lamellar WC/C coating which were deposited by a physical vapor deposition on nitrided AISI 4140 alloy steel. The investigation includes wear evaluation using Pin-on-disk configuration. When WC/C coated AISI 4140 alloy steel slides against EN 8 steel, it was found that carbon-rich coatings show much lower wear of the countersurface than nitrogen-rich coatings. The results were correlated with the properties determined from tribological and mechanical characterization, therefore by probably selecting the proper processing parameters the deposition of WC/C coating results in decreasing the wear rate of the substrate which shows a potential for tribological application.

  19. Bactericidal activity of copper and niobium-alloyed austenitic stainless steel.

    PubMed

    Baena, M I; Márquez, M C; Matres, V; Botella, J; Ventosa, A

    2006-12-01

    Biofouling and microbiologically influenced corrosion are processes of material deterioration that originate from the attachment of microorganisms as quickly as the material is immersed in a nonsterile environment. Stainless steels, despite their wide use in different industries and as appliances and implant materials, do not possess inherent antimicrobial properties. Changes in hygiene legislation and increased public awareness of product quality makes it necessary to devise control methods that inhibit biofilm formation or to act at an early stage of the biofouling process and provide the release of antimicrobial compounds on a sustainable basis and at effective level. These antibacterial stainless steels may find a wide range of applications in fields, such as kitchen appliances, medical equipment, home electronics, and tools and hardware. The purpose of this study was to obtain antibacterial stainless steel and thus mitigate the microbial colonization and bacterial infection. Copper is known as an antibacterial agent; in contrast, niobium has been demonstrated to improve the antimicrobial effect of copper by stimulating the formation of precipitated copper particles and its distribution in the matrix of the stainless steel. Thus, we obtained slides of 3.8% copper and 0.1% niobium alloyed stainless steel; subjected them to three different heat treatment protocols (550 degrees C, 700 degrees C, and 800 degrees C for 100, 200, 300, and 400 hours); and determined their antimicrobial activities by using different initial bacterial cell densities and suspending solutions to apply the bacteria to the stainless steels. The bacterial strain used in these experiments was Escherichia coli CCM 4517. The best antimicrobial effects were observed in the slides of stainless steel treated at 700 degrees C and 800 degrees C using an initial cell density of approximately 10(5) cells ml(-1) and phosphate-buffered saline as the solution in which the bacteria came into contact with

  20. Manufacture of Alumina-Forming Austenitic Steel Alloys by Conventional Casting and Hot-Working Methods

    SciTech Connect

    Brady, M.P.; Yamamoto, Y.; Magee, J.H.

    2009-03-10

    Oak Ridge National Laboratory (ORNL) and Carpenter Technology Corporation (CarTech) participated in an in-kind cost share cooperative research and development agreement (CRADA) effort under the auspices of the Energy Efficiency and Renewable Energy (EERE) Technology Maturation Program to explore the feasibility for scale up of developmental ORNL alumina-forming austenitic (AFA) stainless steels by conventional casting and rolling techniques. CarTech successfully vacuum melted 301b heats of four AFA alloy compositions in the range of Fe-(20-25)Ni-(12-14)Cr-(3-4)Al-(l-2.5)Nb wt.% base. Conventional hot/cold rolling was used to produce 0.5-inch thick plate and 0.1-inch thick sheet product. ORNL subsequently successfully rolled the 0.1-inch sheet to 4 mil thick foil. Long-term oxidation studies of the plate form material were initiated at 650, 700, and 800 C in air with 10 volume percent water vapor. Preliminary results indicated that the alloys exhibit comparable (good) oxidation resistance to ORNL laboratory scale AFA alloy arc casting previously evaluated. The sheet and foil material will be used in ongoing evaluation efforts for oxidation and creep resistance under related CRADAs with two gas turbine engine manufacturers. This work will be directed to evaluation of AFA alloys for use in gas turbine recuperators to permit higher-temperature operating conditions for improved efficiencies and reduced environmental emissions. AFA alloy properties to date have been obtained from small laboratory scale arc-castings made at ORNL. The goal of the ORNL-CarTech CRADA was to establish the viability for producing plate, sheet and foil of the AFA alloys by conventional casting and hot working approaches as a first step towards scale up and commercialization of the AFA alloys. The AFA alloy produced under this effort will then be evaluated in related CRADAs with two gas turbine engine manufacturers for gas turbine recuperator applications.

  1. Alloy Design Based on Computational Thermodynamics and Multi-objective Optimization: The Case of Medium-Mn Steels

    NASA Astrophysics Data System (ADS)

    Aristeidakis, John S.; Haidemenopoulos, Gregory N.

    2017-02-01

    A new alloy design methodology is presented for the identification of alloy compositions, which exhibit process windows (PWs) satisfying specific design objectives and optimized for overall performance. The methodology is applied to the design of medium-Mn steels containing Al and/or Ni. By implementing computational alloy thermodynamics, a large composition space was investigated systematically to map the fraction and stability of retained austenite as a function of intercritical annealing temperature. Alloys exhibiting PWs, i.e., an intercritical annealing range, which when applied satisfies the given design objectives, were identified. A multi-objective optimization method, involving Pareto optimality, was then applied to identify a list of optimum alloy compositions, which maximized retained austenite amount and stability, as well as intercritical annealing temperature, while minimized overall alloy content. A heuristic approach was finally employed in order to rank the optimum alloys. The methodology provided a final short list of alloy compositions and associated PWs ranked according to their overall performance. The proposed methodology could be the first step in the process of computational alloy design of medium-Mn steels or other alloy systems.

  2. Vacuum Brazing TC4 Titanium Alloy to 304 Stainless Steel with Cu-Ti-Ni-Zr-V Amorphous Alloy Foil

    NASA Astrophysics Data System (ADS)

    Dong, Honggang; Yang, Zhonglin; Wang, Zengrui; Deng, Dewei; Dong, Chuang

    2014-10-01

    Dissimilar metal vacuum brazing between TC4 titanium alloy and 304 stainless steel was conducted with newly designed Cu-Ti-Ni-Zr-V amorphous alloy foils as filler metals. Solid joints were obtained due to excellent compatibility between the filler metal and stainless steel substrate. Partial dissolution of stainless steel substrate occurred during brazing. The shear strength of the joint brazed with Cu43.75Ti37.5Ni6.25Zr6.25V6.25 foil was 105 MPa and that with Cu37.5Ti25Ni12.5Zr12.5V12.5 was 116 MPa. All the joints fractured through the gray layer in the brazed seam, revealing brittle fracture features. Cr4Ti, Cu0.8FeTi, Fe8TiZr3 and Al2NiTi3C compounds were found in the fractured joint brazed with Cu43.75Ti37.5Ni6.25Zr6.25V6.25 foil, and Fe2Ti, TiCu, Fe8TiZr3 and NiTi0.8Zr0.3 compounds were detected in the joint brazed with Cu37.5Ti25Ni12.5Zr12.5V12.5 foil. The existence of Cr-Ti, Fe-Ti, Cu-Fe-Ti, and Fe-Ti-V intermetallic compounds in the brazed seam caused fracture of the resultant joints.

  3. SECM Study of Effect of Chromium Content on the Localized Corrosion Behavior of Low-Alloy Steels in Chloride Environment

    NASA Astrophysics Data System (ADS)

    Indira, K.; Nishimura, T.

    2016-10-01

    This paper investigates the effect of chromium (Cr) content (0, 1, 3 and 5% Cr) in epoxy-coated alloy steel against corrosion using in situ electrochemical techniques such as EIS and SECM in a 3% NaCl solution. The EIS results revealed that the epoxy-coated Cr steel exhibited higher impedance values than carbon steel, which is attributed to the greater resistance of Cr steel toward corrosion. Based on the cyclic voltammogram results, the tip potentials were set at -0.7, 0.04 and 0.60 V for determining the concentration of dissolved oxygen at cathodic region, and oxidation of Cr2+ and Fe2+ at anodic region, respectively. The SECM measurements showed that, the tip current in the anodic region has decreased with increase in Cr content of the sample, which indicates that the oxidation of Fe2+ and Cr2+ decreases (corrosion is reduced) with the increase in Cr content of the steel. Besides, 5% Cr steel can maintain the highest corrosion resistance, and 1 and 3% Cr steels have higher corrosion resistance than the 0% Cr steel. This higher corrosion resistance of Cr steel samples could be due to the formation of Cr-rich hydro-oxide layers [Cr(OH)3 as a corrosion product] on the surface of the samples. Thus, the epoxy-coated Cr alloy steel has greater corrosion resistance in a chloride-containing environment than the carbon steel. Hence, epoxy-coated Cr alloy steel can be successfully used as a construction material in structures.

  4. Alloying of steel and graphite by hydrogen in nuclear reactor

    NASA Astrophysics Data System (ADS)

    Krasikov, E.

    2017-02-01

    In traditional power engineering hydrogen may be one of the first primary source of equipment damage. This problem has high actuality for both nuclear and thermonuclear power engineering. Study of radiation-hydrogen embrittlement of the steel raises the question concerning the unknown source of hydrogen in reactors. Later unexpectedly high hydrogen concentrations were detected in irradiated graphite. It is necessary to look for this source of hydrogen especially because hydrogen flakes were detected in reactor vessels of Belgian NPPs. As a possible initial hypothesis about the enigmatical source of hydrogen one can propose protons generation during beta-decay of free neutrons поскольку inasmuch as protons detected by researches at nuclear reactors as witness of beta-decay of free neutrons.

  5. Calculations of the influence of alloying elements (Al, Cr, Mn, Ni, Si) on the Solubility of carbonitrides in low-carbon low-alloy steels

    NASA Astrophysics Data System (ADS)

    Gorbachev, I. I.; Popov, V. V.; Pasynkov, A. Yu.

    2016-12-01

    Based on the CALPHAD method, a thermodynamic description of the Fe- M-V-NB-Ti-C-N system (where M is Al, Cr, Mn, Ni, or Si) has been constructed and, using this description, the solubilities of carbonitrides in austenite for low-alloy low-carbon steels with V, Nb, and Ti have been calculated using 10G2FB steel as an example. The influence of the alloy composition and temperature on the composition and amount of carbonitride phases and on the concentration of these elements in the solid solution has been analyzed.

  6. Alternative Fabrication Routes toward Oxide-Dispersion-Strengthened Steels and Model Alloys

    NASA Astrophysics Data System (ADS)

    Bergner, Frank; Hilger, Isabell; Virta, Jouko; Lagerbom, Juha; Gerbeth, Gunter; Connolly, Sarah; Hong, Zuliang; Grant, Patrick S.; Weissgärber, Thomas

    2016-11-01

    The standard powder metallurgy (PM) route for the fabrication of oxide-dispersion-strengthened (ODS) steels involves gas atomization to produce a prealloyed powder, mechanical alloying (MA) with fine oxide powders, consolidation, and finally thermal/thermomechanical treatment (TMT). It is well established that ODS steels with superior property combinations, for example, creep and tensile strength, can be produced by this PM/MA route. However, the fabrication process is complex and expensive, and the fitness for scaling up to the industrial scale is limited. At the laboratory scale, production of small amounts of well-controlled model systems continues to be desirable for specific purposes, such as modeling-oriented experiments. Thus, from the laboratory to industrial application, there is growing interest in complementary or alternative fabrication routes for ODS steels and related model systems, which offer a different balance of cost, convenience, properties, and scalability. This article reviews the state of the art in ODS alloy fabrication and identifies promising new routes toward ODS steels. The PM/AM route for the fabrication of ODS steels is also described, as it is the current default process. Hybrid routes that comprise aspects of both the PM route and more radical liquid metal (LM) routes are suggested to be promising approaches for larger volumes and higher throughput of fabricated material. Although similar uniformity and refinement of the critical nanometer-sized oxide particles has not yet been demonstrated, ongoing innovations in the LM route are described, along with recent encouraging preliminary results for both extrinsic nano-oxide additions and intrinsic nano-oxide formation in variants of the LM route. Finally, physicochemical methods such as ion beam synthesis are shown to offer interesting perspectives for the fabrication of model systems. As well as literature sources, examples of progress in the authors' groups are also highlighted.

  7. Mechanically Alloyed-Oxide Dispersion Strengthened Steels for Use in Space Nuclear Power Systems

    NASA Astrophysics Data System (ADS)

    El-Genk, Mohamed S.; Tournier, Jean-Michel

    2004-02-01

    The mechanical and thermo-physical properties of Mechanically Alloyed (MA)-Oxide Dispersion Strengthened (ODS) steels are reviewed and their potential for use in space nuclear reactor power systems is examined. The three MA-ODS alloys examined are Inconel MA-ODS754 (77.55Ni, 20Cr, 1Fe, 0.5Ti, 0.3Al, 0.05C, and 0.6Y2O3), Incoloy MA-ODS956 (74.45Fe, 20Cr, 4.5Al, 0.5Ti, 0.05C, 0.5Y2O3), and Incoloy MA-ODS957 (84.55Fe, 14Cr, 0.3Mo, 0.9Ti, 0.25Y2O3). The major advantages of these alloys are: (a) their strength at high temperatures (>1000 K) is relatively higher and decreases slower with temperature than niobium (Nb) and molybdenum (Mo) refractory alloys; (b) they are relatively lightweight and less expensive; (c) they have been shown to experience low swelling and embrittlement with exposure to high-energy neutrons (> 0.1 MeV) up to a fluence of 1023 n/cm2; and (d) their high resistance to oxidation and nitration at high temperatures, which simplifies handling and assembly. These MS-ODS alloys are also lighter and much stronger than 316-stainless steel and super-alloys such as Inconel 601, Haynes 25, and Hastalloy-X at moderately high temperatures (688-1000 K). The little data available on the compatibility of the MA-ODS alloys with alkali liquid metals up to 1100 K are encouraging, however, additional tests at typical operation temperatures (1000-1400 K) in liquid metal cooled and alkali metal heat pipe-cooled space nuclear reactors are needed. The anisotropy of the MA-ODS alloys when cold worked, and in particularly when rolled into tubes, should not hinder their use in space nuclear power systems, in which the operation pressure is either near atmospheric or as high as 2 MPa.

  8. Grain Boundary Segregation Behavior of Boron in Low-Alloy Steel

    NASA Astrophysics Data System (ADS)

    Shigesato, Genichi; Fujishiro, Taishi; Hara, Takuya

    2014-04-01

    The boron concentration profiles around prior austenite grain boundaries in Fe-0.05C-0.5Mo-0.001B (mass pct) are examined using aberration-corrected STEM-EELS. In order to obtain the precise distribution of boron around the boundaries, tilt series measurements with thin specimens (<30 nm) are performed and the EEL spectra are analyzed by principal component analysis (PCA) and multivariate curve resolution (MCR). The boron concentration profile changes with the cooling rate from the solid solution temperature. The concentration at grain boundaries is maximized at a medium rate (30 °C/s), where the concentration reaches 8 at. pct, and it decreases at a larger (250 °C/s) or smaller (5 °C/s) rate. On the other hand, the boron distribution becomes wider as the cooling rate becomes smaller. The current results suggest that the boron segregation in the alloy is formed by the "non-equilibrium segregation mechanism."

  9. A novel active fire protection approach for structural steel members using NiTi shape memory alloy

    NASA Astrophysics Data System (ADS)

    Sadiq, H.; Wong, M. B.; Al-Mahaidi, R.; Zhao, X. L.

    2013-02-01

    A novel active fire protection approach, based on integrating a shape memory alloy, NiTi, with a steel structure, was proposed to satisfy the fire resistance requirements in structural design. To demonstrate the principles of this approach, a simple structure in the form of a simply supported steel beam was used. The internal action of the beam due to a transverse applied load was reduced by utilizing the shape memory effect in the NiTi alloy at rising temperatures. As a result, the net internal action from the load design was kept below the deteriorated load capacity of the beam during the fire scenario for period of time that was longer than that of the original beam without the NiTi alloy. By integrating the NiTi alloy into the beam system, the structure remained stable even though the steel temperature exceeded the critical temperature which may have caused the original beam structure to collapse. Prior to testing the composite NiTi-steel beam under simulated fire conditions, the NiTi alloy specimens were characterized at high temperatures. At 300 °C, the stiffness of the specimens increased by three times and its strength by four times over that at room temperature. The results obtained from the high-temperature characterization highlighted the great potential of the alloy being used in fire engineering applications.

  10. Phase chemistry and precipitation reactions in maraging steels: Part 3. Model alloys

    SciTech Connect

    Sha, W. .Department of Materials Science and Metallurgy); Cerezo, A.; Smith, G.D.W. . Department of Materials)

    1993-06-01

    This article describes studies of phase transformations during aging in a variety of model maraging steels. Atom-probe field-ion microscopy (APFIM) was the main research technique employed. Thermochemical calculation was also used during the course of the work. The composition and morphology of precipitates were compared in several maraging systems aged at different temperatures for different times to investigate the aging sequence. The APFIM results are compared with studies by other workers using different experimental techniques. In Fe-Ni(-Co)-Mo model alloys, [omega] phase and Fe[sub 7]Mo[sub 6] [mu] phase have been found to contribute to age hardening at different stages of aging; no evidence was found for the existence of Mo-rich clusters in the as-quenched Fe-Ni-Co-Mo alloy. In a high-Si Cr-containing steel, Ti[sub 6]Si[sub 7]Ni[sub 16]G phase and Ni[sub 3]Ti have been found to contribute to age hardening; reverted austenite was found after aging for 5 hours at 520 [degree]C. In a Mn-containing steel, Fe[sub 2]Mo Laves phase and a structurally uncertain phase with a composition of Fe[sub 45]Mn[sub 32]Co[sub 5]Mo[sub 19] have been found to contribute to age hardening.

  11. Microstructural characterization of dissimilar welds between alloy 800 and HP heat-resistant steel

    SciTech Connect

    Dehmolaei, R.; Shamanian, M. Kermanpur, A.

    2008-10-15

    In this study, dissimilar welds between HP heat-resistant steel and Incoloy 800 were made with four different filler materials including: 309 stainless steel and nickel-based Inconel 82, 182 and 617. The microstructure of the base metals, weld metals and their interfaces were characterized by utilizing optical and scanning electron microscopy. Grain boundaries migration in the weld metals was studied. It was found that the migration of grain boundaries in the Inconel 82 weld metal was very extensive. Precipitates of TiC and M{sub 23}C{sub 6} (M = Cr and Mo) in the Inconel 617 weld metal are identified. The necessary conditions for the formation of cracks close to the fusion line of the 309-HP joints are described. Furthermore unmixed zone near the fusion line between HP steel base metal and Inconel 82 weld metal is discussed. An epitaxial growth is characterized at the fusion line of the 309-Alloy 800 and Inconel 617-Alloy 800 joints.

  12. Evaluation of the stress corrosion cracking resistance of several high strength low alloy steels

    NASA Technical Reports Server (NTRS)

    Humphries, T. S.; Nelson, E. E.

    1980-01-01

    The stress corrosion cracking resistance was studied for high strength alloy steels 4130, 4340, for H-11 at selected strength levels, and for D6AC and HY140 at a single strength. Round tensile and C-ring type specimens were stressed up to 100 percent of their yield strengths and exposed to alternate immersion in salt water, salt spray, the atmosphere at Marshall Space Flight Center, and the seacoast at Kennedy Space Center. Under the test conditions, 4130 and 4340 steels heat treated to a tensile strength of 1240 MPa (180 ksi), H-11 and D6AC heat treated to a tensile strength of 1450 MPa (210 ksi), and HY140 (1020 MPa, 148 ksi) are resistant to stress corrosion cracking because failures were not encountered at stress levels up to 75 percent of their yield strengths. A maximum exposure period of one month for alternate immersion in salt water or salt spray and three months for seacoast is indicated for alloy steel to avoid false indications of stress corrosion cracking because of failure resulting from severe pitting.

  13. Effects of gaseous nitriding AISI4140 alloy steel on corrosion and hardness properties

    NASA Astrophysics Data System (ADS)

    Tamil Moli, L.; Wahab, N.; Gopinathan, M.; Karmegam, K.; Maniyarasi, M.

    2016-10-01

    Corrosion is one of the major problems in the industry especially on machinery since it weakens the structure of the machinery part and causes the mechanical failure. This will stop the production and increase the maintenance cost. In this study, the corrosion behaviour of gas nitriding on a screw press machine shaft made from AISI 4140 steel was investigated. Pitting corrosion was identified as a major cause of the shaft failure and this study was conducted to improve the corrosion resistance on the AISI 4140 alloy steel shaft by gas nitriding as a surface hardening treatment. Gas nitriding was performed with composition of 15% ammonia and 85% nitrogen at temperatures of 525 °C, 550 °C and 575 °C and with the soaking time of 30, 45 and 60 minutes, respectively. The samples were prepared as rectangular sized of 30mm x 12mm x 3mm for immersion testing. The results showed that corrosion rate of untreated samples was 77% higher compared to the nitrided samples. It was also found that hardness of the nitrided samples was higher than untreated sample. All in all, it can be concluded that gaseous nitriding can significantly improve the surface hardness and the corrosion resistance of the shaft made of AISI 4140 alloy steel, hence reduces the pitting that is the root cause of failure.

  14. Study of electroless Ni-W-P alloy coating on martensitic stainless steel

    NASA Astrophysics Data System (ADS)

    Nikitasari, Arini; Mabruri, Efendi

    2016-04-01

    Electroless nickel phospor (Ni-P) is widely used in many industries due to their corrosion and wear resistance, coating uniformity, and ability to coat non-conductive surfaces. The unique properties of tungsten such as high hardness, higher melting point, lower coefficient of linear thermal expansion, and high tensile strength have created a lot of interest in developing ternary Ni-W-P alloys. This article presents the study of electroless Ni-W-P alloys coating using acid or alkaline bath on martensitic stainless steel. Nickel sulfate and sodium tungstate were used as nickel and tungsten sources, respectively, and sodium hypophosphite was used as a reducing agent. Acid or alkaline bath refer to bath pH condition was adjusted by adding sulfuric acid. Martensitic stainless steel was immersed in Ni-W-P bath for 15, 30, and 60 minutes. The substrate of martensitic stainless steel was subjected to pre-treatment (polishing and cleaning) and activation prior to electroless plating. The plating characteristics were investigated for concentration ratio of nickel and hypophosphite (1:3), sodium tungstate concentration 0,1 M, immersion time (15 min, 30 min, 60 min), and bath condition (acid, alkaline). The electroless Ni-W-P plating was heat treated at 400°C for 1 hour. Deposits were characterized using scanning electron microscope (SEM) and corrosion measurement system (CMS).

  15. Shake table tests and analytical simulations of a steel structure with shape memory alloy dampers

    NASA Astrophysics Data System (ADS)

    Parulekar, Y. M.; Kiran, A. Ravi; Reddy, G. R.; Singh, R. K.; Vaze, K. K.

    2014-12-01

    This study uses the pseudoelastic properties of Ni-Ti shape memory alloy wires for attenuation of the seismic response of a steel structure and evaluates its effectiveness and applicability in seismic response control. In this paper, shake table tests, carried out on a model of a steel structure with and without wire-based shape memory alloy dampers, are discussed in detail. Shake table tests, comprised of free vibration tests and spectrum compatible time history tests, were carried out. The former were used for the evaluation of the frequency and damping, and the later were used to prove the efficacy of the shape memory alloy dampers. Further analytical simulations are carried out using detailed time history analysis utilizing a thermomechanical model of an SMA and taking into account the residual martensite accumulation, which is irreversibly due to cyclic forward/reverse martensitic transformation. Moreover, a simple iterative response spectrum (IRS) method with equivalent damping and stiffness is also used to evaluate the response of the structure with SMA dampers, and it is proved that the method can be conservatively used by designers.

  16. Thermal Diffusivity and Thermal Conductivity of Five Different Steel Alloys in the Solid and Liquid Phases

    NASA Astrophysics Data System (ADS)

    Wilthan, B.; Schützenhöfer, W.; Pottlacher, G.

    2015-08-01

    The need for characterization of thermophysical properties of steel and nickel-based alloys was addressed in the FFG-Bridge Project 810999 in cooperation with a partner from industry, Böhler Edelstahl GmbH & Co KG. To optimize numerical simulations of production processes, such as remelting or plastic deformation, additional, and more accurate data were necessary for the alloys under investigation. With a fast ohmic pulse heating circuit system, the temperature-dependent specific electrical resistivity, density, and specific heat capacity for a set of five high alloyed steels were measured. Hence, using the Wiedemann-Franz law with a Lorenz number of , the thermal diffusivity and thermal conductivity could be calculated for the solid and liquid phases up to temperatures of 2500 K. This experimental approach is limited by the following requirements for the specimens: they have to be electrically conducting, the melting point has to be high enough for the implemented pyrometric temperature measurement, and one has to be able to draw wires of the material. The latter restriction is technologically challenging with some of the materials being very brittle. For all samples, electrical and temperature signals are recorded and a fast shadowgraph method is used to measure the volume expansion. For each material under investigation, a set of data including the chemical composition, the density at room temperature, solidus and liquidus temperatures, and the change of enthalpy, resistivity, density, thermal conductivity, and thermal diffusivity as a function of temperature is reported.

  17. Study of ultrasonically assisted turning of stainless steel and brass alloys

    NASA Astrophysics Data System (ADS)

    Mahdy, S. M. A.; Gouda, M. A.; Silberschmidt, V. V.

    2013-07-01

    Ultrasonically assisted turning (UAT) is a hybrid machining technique employing high-frequency small-amplitude vibration superimposed on the tool movement during turning. It is superior to conventional turning (CT) with regard to cutting forces, surface quality and machining accuracy. The aim of this study is to investigate the effect of different machining parameters on stainless steel and brass alloys, during both UAT and CT, and evaluate improvements of cutting forces, surface roughness, surface integrity, and machining accuracy. An experimental setup for UAT at Loughborough University was used to accomplish this investigation. This setup used a Picoscope data acquisition add-on with Kistler three-component dynamometer, Seco DNMG cutting inserts were utilized, a surface tester from Taylor Hobson was used to evaluate surface roughness, Alicona Infinite Focus microscope was used to evaluate surface roughness and surface integrity, while Metris CMM with Renishaw probe was employed to evaluate machining accuracy. Cylindrical workpieces of steel and brass alloys were turned under CT and UAT conditions; cutting forces, surface roughness, and machining accuracy produced with both techniques where compared. Significant improvements were noticed in the ultrasonically assisted machining when compared to the CT for both alloys.

  18. Microstructure design of low alloy transformation-induced plasticity assisted steels

    NASA Astrophysics Data System (ADS)

    Zhu, Ruixian

    The microstructure of low alloy Transformation Induced Plasticity (TRIP) assisted steels has been systematically varied through the combination of computational and experimental methodologies in order to enhance the mechanical performance and to fulfill the requirement of the next generation Advanced High Strength Steels (AHSS). The roles of microstructural parameters, such as phase constitutions, phase stability, and volume fractions on the strength-ductility combination have been revealed. Two model alloy compositions (i.e. Fe-1.5Mn-1.5Si-0.3C, and Fe-3Mn-1Si-0.3C in wt%, nominal composition) were studied. Multiphase microstructures including ferrite, bainite, retained austenite and martensite were obtained through conventional two step heat treatment (i.e. intercritical annealing-IA, and bainitic isothermal transformation-BIT). The effect of phase constitution on the mechanical properties was first characterized experimentally via systematically varying the volume fractions of these phases through computational thermodynamics. It was found that martensite was the main phase to deteriorate ductility, meanwhile the C/VA ratio (i.e. carbon content over the volume fraction of austenite) could be another indicator for the ductility of the multiphase microstructure. Following the microstructural characterization of the multiphase alloys, two microstructural design criteria (i.e. maximizing ferrite and austenite, suppressing athermal martensite) were proposed in order to optimize the corresponding mechanical performance. The volume fraction of ferrite was maximized during the IA with the help of computational thermodyanmics. On the other hand, it turned out theoretically that the martensite suppression could not be avoided on the low Mn contained alloy (i.e. Fe- 1.5Mn-1.5Si-0.3C). Nevertheless, the achieved combination of strength (~1300MPa true strength) and ductility (˜23% uniform elongation) on the low Mn alloy following the proposed design criteria fulfilled the

  19. Temperature and environmentally assisted cracking in low alloy steel

    SciTech Connect

    Auten, T.A.; Monter, J.V.

    1995-12-31

    Environmentally assisted cracking (EAC) can be defined as the propagation of fatigue cracks in water at rates that are anywhere from 3 to over 40 times the growth rates expected in air. In the present work, five ASTM A 508 Class 2 forgings with ladle and check analyses that ranged from 0.010 to 0.019 wt% S were tested in high purity deaerated water in the temperature range of 93 to 260 C. At 260 C these forgings did not undergo EAC, reinforcing earlier results for two similar forgings. This broad sampling indicates a strong resistance to EAC for this class of forging at 260 C. On the other hand, EAC occurred consistently in the three of these forgings that were tested below 204 C, provided the test conditions were high enough to produce a high baseline fatigue crack growth rate (FCGR), where the baseline FCGR is that expected in air. At 149 C, EAC occurred at test conditions that combined to yield a baseline FCGR greater than {approx}2E-6 mm/s. At 204, 121, and 93 C, this ``critical crack growth rate`` appeared to shift to lower baseline values. The EAC that occurred at lower temperatures was a factor of 3 to 12 times higher than baseline air rates, which was not as strong as the effect for higher sulfur steels at 240 to 290 C. Also, no plateau in the growth rates occurred as it does with the higher sulfur steels. In another approach, EAC was induced at 93 and at 260 C by raising the dissolved oxygen content of the water from <10 to >15 ppb. In this case, the EAC growth rates decreased to non-EAC levels when the oxygen supply was shut off. The oxygen-related EAC occurred over a broader range of baseline growth rates than found for the EAC driven by the baseline crack tip speed. Again, this can be rationalized by the buildup of sulfur in the crack tip water, which can be associated with the higher corrosion potential of the bulk water.

  20. Critical Aspects of Alloying of Sintered Steels with Manganese

    NASA Astrophysics Data System (ADS)

    Hryha, Eduard; Dudrova, Eva; Nyborg, Lars

    2010-11-01

    This study examines the sintering behavior and properties of Fe-0.8Mn-0.5C manganese powder metallurgy steels. The study focuses on the influence of mode of alloying—admixing using either high-purity electrolytic manganese or medium carbon ferromanganese as well as the fully prealloying of water-atomized powder. Three main aspects were studied during the whole sintering process—microstructure development, interparticle necks evolution, and changes in the behavior of manganese carrier particles during both heating and sintering stages. The prealloyed powder shows considerable improvement in carbon homogenization and interparticle neck development in comparison with admixed materials. The first indication of pearlite for the fully prealloyed material was registered at ~1013 K (740 °C) in comparison with ~1098 K (825 °C) in the case of the admixed systems. The negative effect of the oxidized residuals of manganese carrier particles and high microstructure inhomogeneity, which is a characteristic feature of admixed systems, is reflected in the lower values of the mechanical properties. The worst results in this respect were obtained for the system admixed with electrolytic manganese because of more intensive manganese sublimation and resulting oxidation at lower temperatures. According to the results of X-ray photoelectron spectroscopy and high-resolution scanning electron microscopy and energy dispersive X-ray analyses, the observed high brittleness of admixed materials is connected with intergranular decohesion failure associated with manganese oxide formation on the grain boundaries.

  1. High Power Laser Welding. [of stainless steel and titanium alloy structures

    NASA Technical Reports Server (NTRS)

    Banas, C. M.

    1972-01-01

    A review of recent developments in high power, carbon dixoide laser welding is presented. Deep penetration welding in stainless steel to 0.5-in. thick, high speed welding in thin gage rimmed steel and gas shielded welding in Ti-6Al-4V alloy are described. The effects of laser power, power density, focusing optics, gas-shielding techniques, material properties and weld speed on weld quality and penetration are discussed. It is shown that laser welding performance in thin materials is comparable to that of electron beams. It is further shown that high quality welds, as evidenced by NDT, mechanical and metal-lographic tests, can be achieved. The potential of the laser for industrial welding applications is indicated.

  2. Assessment of precipitation in alloy steel using nonlinear Rayleigh surface waves

    NASA Astrophysics Data System (ADS)

    Thiele, Sebastian; Matlack, Kathryn H.; Kim, Jin-Yeon; Qu, Jianmin; Wall, James J.; Jacobs, Laurence J.

    2014-02-01

    Nonlinear ultrasonic waves have shown to be sensitive to various microstructural changes in metals including coherent precipitates; these precipitates introduce a strain field in the lattice structure. The thermal aging of certain alloy steels leads to the formation of coherent precipitates, which pin dislocations and contribute to the generation of a second harmonic component. A precipitate hardenable material namely 17-4 PH stainless steel is thermally treated in this research to obtain different precipitation stages, and then the influence of precipitates on the acoustic nonlinearity parameter is assessed. Conclusions about the microstrucutural changes in the material are drawn based on the results from a nonlinear Rayleigh surface wave measurement and complementary thermo-electric power, hardness and ultrasonic velocity measurements. The results show that the nonlinear parameter is sensitive to coherent precipitates in the material and moreover that precipitation characteristics can be characterized based on the obtained experimental data.

  3. Dynamic deformation and fragmentation response of maraging steel linear cellular alloy

    NASA Astrophysics Data System (ADS)

    Jakus, Adam E.; Fredenberg, David A.; McCoy, Tammy; Thadhani, Naresh; Cochran, Joe K.

    2012-03-01

    The dynamic deformation and fragmentation response of 25% dense 9-cell linear cellular alloy (LCA) made of unaged 250 maraging steel, fabricated using a direct reduction and extrusion technique, is investigated. Explicit finite element simulations were implemented using AUTODYN finite element code. The maraging steel properties were defined using a Johnson-Cook strength model with previously validated parameters. Rod-on-anvil impact tests were performed using the 7.6mm helium gas gun and the transient deformation and fragmentation response was recorded with highspeed imaging. Analysis of observed deformation states of specimens and finite element simulations reveal that in the case of the 9-cell LCA, dissipation of stress and strain occurs along the interior cell wells resulting in significant and ubiquitous buckling prior to confined fragmentation.

  4. Investigation of dynamic dry friction between stainless steel and aluminium alloy

    NASA Astrophysics Data System (ADS)

    Keightley, Peter; Winter, Ron; Stirk, Stewart

    2009-06-01

    Previous workers studied dynamic friction by using an impacting copper plate to drive a tapered aluminium alloy plug into a matching hole in a stainless steel outer sheath. The velocity of the back surface of the plug was measured using velocity interferometry. We have performed experiments on a version of this basic configuration that has been enlarged so that the sliding surfaces remain in contact for a longer time than with the original configuration. By comparing our results with computer simulations we conclude that the frictional forces between the inner cone and the steel outer are initially high but decrease significantly as the sliding proceeds. This effect is assumed to result from thermal softening of the material at the sliding interface. The study is supported by metallography of the recovered components.

  5. Surface Modification of Micro-Alloyed High-Strength Low-Alloy Steel by Controlled TIG Arcing Process

    NASA Astrophysics Data System (ADS)

    Ghosh, P. K.; Kumar, Ravindra

    2015-02-01

    Surface modification of micro-alloyed HSLA steel plate has been carried out by autogenous conventional and pulse current tungsten inert gas arcing (TIGA) processes at different welding parameters while the energy input was kept constant. At a given energy input the influence of pulse parameters on the characteristics of surface modification has been studied in case of employing single and multi-run procedure. The role of pulse parameters has been studied by considering their summarized influence defined by a factor Φ. The variation in Φ and pulse frequency has been found to significantly affect the thermal behavior of fusion and accordingly the width and penetration of the modified region along with its microstructure, hardness and wear characteristics. It is found that pulsed TIGA is relatively more advantageous over the conventional TIGA process, as it leads to higher hardness, improved wear resistance, and a better control over surface characteristics.

  6. EXAMINATION OF THE OXIDATION PROTECTION OF ZINC COATINGS FORMED ON COPPER ALLOYS AND STEEL SUBSTRATES

    SciTech Connect

    Papazoglou, M.; Chaliampalias, D.; Vourlias, G.; Pavlidou, E.; Stergioudis, G.; Skolianos, S.

    2010-01-21

    The exposure of metallic components at aggressive high temperature environments, usually limit their usage at similar application because they suffer from severe oxidation attack. Copper alloys are used in a wide range of high-quality indoor and outdoor applications, statue parts, art hardware, high strength and high thermal conductivity applications. On the other hand, steel is commonly used as mechanical part of industrial set outs or in the construction sector due to its high mechanical properties. The aim of the present work is the examination of the oxidation resistance of pack cementation zinc coatings deposited on copper, leaded brass and steel substrates at elevated temperature conditions. Furthermore, an effort made to make a long-term evaluation of the coated samples durability. The oxidation results showed that bare substrates appear to have undergone severe damage comparing with the coated ones. Furthermore, the mass gain of the uncoated samples was higher than this of the zinc covered ones. Particularly zinc coated brass was found to be more resistant to oxidation conditions in which it was exposed as it has the lower mass gain as compared to the bare substrates and zinc coated copper. Zinc coated steel was also proved to be more resistive than the uncoated steel.

  7. Improvement of Laser Deposited High Alloyed Powder Metallurgical Tool Steel by a Post-tempering Treatment

    NASA Astrophysics Data System (ADS)

    Leunda, J.; Navas, V. García; Soriano, C.; Sanz, C.

    Laser cladding process of a high alloyed powder metallurgical tool steel was studied for die repairing purposes. The low hardness obtained after the deposition process was improved by later tempering cycles, achieving crack free coatings with hardness well above 700 HV. The effect of different post tempering cycles was investigated in order to determine the optimal temperature range. The microstructure of the samples was studied using optical and scanning electron microscope and the volumetric ratio of retained austenite was determined by X-ray diffraction. The tempering effect was mainly evaluated through cross-section microhardness profiles.

  8. Microstructural, mechanical and magnetic properties of high-strength low-alloy steel

    NASA Astrophysics Data System (ADS)

    Narayan, S. Prakash; Rao, V.; Mohanty, O. N.

    1991-06-01

    Studies have been carried out on commercial grade high-strength low-alloy steel, microalloyed with Nb, V and Ti with a view to developing high-strength material with moderate soft magnetic properties. In order to obtain a suitable microstructure necessary for achieving the desired mechanical strength and magnetic properties, spheroidisation annealing (SA) as well as quenching and tempering (QT) treatments have been employed. At longer annealing or tempering time (⩾ 30 h), both the SA and QT samples have shown ample spheroidisation of carbides resulting in considerable improvement in the magnetic properties without much deterioration in mechanical strength.

  9. Status of ATR-A1 irradiation experiment on vanadium alloys and low-activation steels

    SciTech Connect

    Tsai, H.; Strain, R.V.; Gomes, I.; Chung, H.; Smith, D.L.

    1997-04-01

    The ATR-A1 irradiation experiment in the Advanced Test Reactor (ATR) was a collaborative U.S./Japan effort to study at low temperatures the effects of neutron damage on vanadium alloys. The experiment also contained a limited quantity of low-activation ferritic steel specimens from Japan as part of the collaboration agreement. The irradiation was completed on May 5, 1996, as planned, after achieving an estimated neutron damage of 4.7 dpa in vanadium. The capsule has since been kept in the ATR water canal for the required radioactivity cool-down. Planning is underway for disassembly of the capsule and test specimen retrieval.

  10. Alloy Shrinkage factors for the investment casting of 17-4PH stainless steel parts

    SciTech Connect

    Sabau, Adrian S; Porter, Wallace D

    2008-01-01

    In this study, the alloy shrinkage factors were obtained for the investment casting of 17-4PH stainless steel parts. For the investment casting process, unfilled wax and fused silica with a zircon prime coat were used for patterns and shell molds, respectively. Dimensions of the die tooling, wax pattern, and casting were measured using a Coordinate Measurement Machine. For all the properties, the experimental data available in the literature did not cover the entire temperature range necessary for process simulation. A comparison between the predicted material property data measured property data is made. It was found that most material properties were accurately predicted over the most of the temperature range of the process. Several assumptions were made in order to obtain a complete set of mechanical property data at high temperatures. Thermal expansion measurements for the 17-4PH alloy were conducted at heating and cooling. As a function of temperature, the thermal expansion for both the alloy and shell mold materials showed different evolution at heating and cooling. Thus, one generic simulation were performed with thermal expansion obtained at heating and another one with thermal expansion obtained at cooling. The alloy dimensions were obtained from numerical simulation results of solidification, heat transfer, and deformation phenomena. As compared with experimental results, the numerical simulation results for the shrinkage factors were slightly over-predicted.

  11. DC electrodeposition of Mn–Co alloys on stainless steels for SOFC interconnect application

    SciTech Connect

    Wu, Junwei; Jiang, Yinglu; Johnson, Christopher; Liu, Xingbo

    2008-03-01

    High conductivity coatings that resist oxide scale growth and reduce chromium evaporation are needed to make stainless steel interconnect materials viable for long-term stable operation of solid oxide fuel cells (SOFC). Mn1.5Co1.5O4 spinel is one of the most promising coatings for interconnect application because of its high conductivity, good chromium retention capability, as well as good CTE match to ferritic stainless steels. Mn–Co electrodeposition followed by oxidization is potentially a low cost method for fabrication of (Mn,Co)3O4 spinel coatings. This work looks at the co-deposition of Mn–Co alloys for this application. As a guide to optimize the deposition process, characterizations of the cathodic reactions and reaction potentials are done using polarization curves. It was found that as cobalt concentration was varied that the alloy composition became richer in cobalt, indicating that the deposition is regular co-deposition process. It was also found that at 0.05M Co concentration in excess gluconate the Mn–Co alloys composition could be tuned by varying the current density. Coatings with Mn–Co around 1:1 could be obtained at a current density of 250 mA/cm2. However, the higher potential increased hydrogen production making the films more porous. Oxidation of the alloy coatings showed that much of the porosities could be eliminated during oxidation. It was found in a number of samples that fully dense coatings where obtained. The composition of the oxidized coating was found to become enriched in Mn, possibly due to the Mn fast diffusion from the substrate.

  12. Brazing open cell reticulated copper foam to stainless steel tubing with vacuum furnace brazed gold/indium alloy plating

    DOEpatents

    Howard, Stanley R.; Korinko, Paul S.

    2008-05-27

    A method of fabricating a heat exchanger includes brush electroplating plated layers for a brazing alloy onto a stainless steel tube in thin layers, over a nickel strike having a 1.3 .mu.m thickness. The resultant Au-18 In composition may be applied as a first layer of indium, 1.47 .mu.m thick, and a second layer of gold, 2.54 .mu.m thick. The order of plating helps control brazing erosion. Excessive amounts of brazing material are avoided by controlling the electroplating process. The reticulated copper foam rings are interference fit to the stainless steel tube, and in contact with the plated layers. The copper foam rings, the plated layers for brazing alloy, and the stainless steel tube are heated and cooled in a vacuum furnace at controlled rates, forming a bond of the copper foam rings to the stainless steel tube that improves heat transfer between the tube and the copper foam.

  13. Alloying the X40CrMoV5-1 steel surface layer with tungsten carbide by the use of a high power diode laser

    NASA Astrophysics Data System (ADS)

    Dobrzański, L. A.; Bonek, M.; Hajduczek, E.; Klimpel, A.

    2005-07-01

    The paper presents the effect of alloying with tungsten carbide on properties of the X40CrMoV5-1 steel surface layer, using the high power diode laser (HPDL). Selection of laser operating conditions is discussed, as well as thickness of the alloying layer, and their influence on structure and chemical composition of the steel. Analysis of the influence of the process conditions on the thicknesses of the alloyed layer and heat-affected zone is presented.

  14. Influence of the pulsed plasma treatment on the corrosion resistance of the low-alloy steel plated by Ni-based alloy

    NASA Astrophysics Data System (ADS)

    Dzhumaev, P.; Yakushin, V.; Kalin, B.; Polsky, V.; Yurlova, M.

    2016-04-01

    This paper presents investigation results of the influence of high temperature pulsed plasma flows (HTPPF) treatment on the corrosion resistance of low-alloy steel 0.2C-Cr-Mn- Ni-Mo cladded by the rapidly quenched nickel-based alloy. A technique that allows obtaining a defect-free clad layer with a good adhesion to the substrate was developed. It is shown that the preliminary treatment of steel samples by nitrogen plasma flows significantly increases their corrosion resistance in the conditions of intergranular corrosion test in a water solution of sulfuric acid. A change of the corrosion mechanism of the clad layer from intergranular to uniform corrosion was observed as a result of sub-microcrystalline structure formation and homogeneous distribution of alloying elements in the plasma treated surface layer thus leading to the significant increase of the corrosion resistance.

  15. Low temperature mechanical properties, fractographic and metallographic evaluation of several alloy steels

    NASA Technical Reports Server (NTRS)

    Montano, J. W.

    1973-01-01

    The mechanical properties are presented of alloy steels, 4130, 4140, 4340, 6150, and 8740. Test specimens were manufactured from approximately 1.00 inch (2.54 cm) diameter bar stock which had been heat treated to two different hardness levels. The following mechanical tests were performed at temperatures of 80 F (+26.7 C), 0 F (-17.8 C), -100 F (-73 C), and -200 F (-129 C): (1) tensile test (Ultimate, yield, modulus, elongation, and reduction of area), (2) notched tensile test, (3) charpy V-notched impact test (impact energy), and (4) double shear strength test (ultimate and yield). The test data indicate excellent tensile strength, notched/unnotched tensile ratios, ductility, impact, and shear properties at all test temperatures, except at -200 F (-129 C) where the impact strength of the higher strength group of alloy steels, 4130 (Rc-37) and 4140 (Rc-44) decreased to approximately 9 ft. lbs. (12 joules) and 6 ft. lbs. (8 joules), respectively. Chemical, metallographic, and fractographic analyses were also performed to evaluate microstructure, microhardness and the effect of decrease in temperature on the ductile to brittle failure transition.

  16. Initial bacterial deposition on bare and zeolite-coated aluminum alloy and stainless steel.

    PubMed

    Chen, Gexin; Beving, Derek E; Bedi, Rajwant S; Yan, Yushan S; Walker, Sharon L

    2009-02-03

    In this study, the impact of zeolite thin film coatings on bacterial deposition and "biofouling" of surfaces has been investigated in an aqueous environment. The synthesis of two types of zeolite coatings, ZSM-5 coated on aluminum alloy and zeolite A coated on stainless steel, and the characterization of the coated and bare metal surfaces are described. The extent of cell deposition onto the bare and zeolite-coated aluminum alloy and stainless steel surfaces is investigated in a parallel plate flow chamber system under a laminar flow conditions. The initial rates of bacterial transfer to the various surfaces are compared by utilizing a marine bacterium, Halomonas pacifica g, under a range of ionic strength conditions. H. pacifica g deposited onto bare metal surfaces to a greater extent as compared with cells deposited onto the zeolite coatings. The surface properties found to have the most notable effect on attachment are the electrokinetic and hydrophobicity properties of the metal and zeolite-coated surfaces. These results suggest that a combination of two chemical mechanisms-hydrophobic and electrostatic interactions-contribute to the antifouling nature of the zeolite surface. Additional observations on the relative role of the hydrodynamic and physical phenomena are also discussed.

  17. Mechanical properties of low-alloy-steels with bainitic microstructures and varying carbon content

    NASA Astrophysics Data System (ADS)

    Weber, A.; Klarner, J.; Vogl, T.; Schöngrundner, R.; Sam, G.; Buchmayr, B.

    2016-03-01

    Materials used in the oilfield industry are subjected to special conditions. These requirements for seamless steel tubes are between the priorities of strength, toughness and sour gas resistance. Steels with bainitic microstructure provide a great opportunity for those harsh environmental conditions. With different morphologies of bainite, like carbide free, upper or lower bainite, the interaction of high tensile strength and elongation is assumed to be better than with tempered martensite. To form carbide free bainite two ways of processing are proposed, isothermal holding with accurate time control or controlled continuous cooling. Both require knowledge of time-temperature transformation behaviour, which can be reached through a detailed alloying concept, focused on the influence of silicon to supress the carbide nucleation and chromium to stabilize the austenite fraction. The present work is based on three alloys with varying silicon and chromium contents. The carbide free microstructure is obtained by a continuous cooling path. Additionally different heat treatments were done to compare the inherent performance of the bainitic morphologies. The bainitic structures were characterized metallographically for their microstructure and the primary phase by means of transmission electron microscopy. The mechanical properties of carbide-free structures were analysed with quasi-static tensile tests and Charpy impact tests. Moreover, investigations about hydrogen embrittlement were done with focus on the effect of retained austenite. The results were ranked and compared qualitatively.

  18. Antimony-induced embrittlement in welding heat-affected zones in a Cr-Mo low-alloy steel

    NASA Astrophysics Data System (ADS)

    Zheng, L.; Song, S.-H.

    2013-07-01

    Heat-affected zones (HAZs) were simulated with a peak temperature of 1320 °C at different welding heat inputs for a Cr-Mo low-alloy steel. The ductile-to-brittle transition temperature (DBTT) of the HAZs increased with increasing heat input. When 0.05 wt.% Sb was added to the steel, the DBTTs of the HAZs became 1 and 10 °C higher than those for the undoped steel at heat inputs of 36 and 60 kJ/cm, respectively. Sb segregation to austenite grain boundaries during thermal cycling was found to be mainly responsible for the DBTT increase.

  19. The Role of Vanadium Carbide Traps in Reducing the Hydrogen Embrittlement Susceptibility of High Strength Alloy Steels.

    DTIC Science & Technology

    1998-08-01

    A723 steel was not sufficient to induce any appreciable embrittlement. 7.0 4.0 HY80 X 0.0i-r 50 4340 r—,—,—|—i—i—i—r—t—i—i—i—i—I—i—’—’—> l...carbide, V4C3) was identified in the A723 steel by x- ray diffraction. V4C3 traps effectively reduced the hydrogen concentrations at the crack ...ALLOY STEELS G. L. SPENCER D. J. DUQUETTE AUGUST 1998 US ARMY ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER CLOSE COMBAT ARMAMENTS CENTER

  20. Initiation of environmentally-assisted cracking in low-alloy steels

    SciTech Connect

    Wire, G.L.; Li, Y.Y.

    1996-06-01

    Environmentally-Assisted Cracking (EAC) in low alloy steels is activated by a critical level of sulfide ions at the crack tip, which is produced from dissolution of sulfide inclusions (MnS, FeS, etc.) in the steel following exposure by a growing crack. EAC of concern herein is the increase of fatigue crack growth rate of up to 40 to 100 times the rate in air that occurs at 240--300 C in high temperature LWR or boiler water environments. The initiation of EAC is the onset of the higher fatigue crack growth rates in fully developed cracks already presumed to be present due to fatigue, stress corrosion cracking, or induced by fabrication. Initiation of EAC is induced by a change in loading parameters causing the fatigue crack growth rate to increase from a small multiple (2--4) to 40--100 times the air rate. A steady state theory developed by Combrade, suggests that EAC will initiate only above a critical crack velocity and cease below this same velocity. However, more recent tests show that EAC can persist down to much lower velocities (100 times lower) in low oxygen water at slightly lower temperatures. A special set of experiments on high sulfur plate material demonstrate that EAC will not initiate from surface cracks with low sulfide inventories at low crack tip velocities. Transient diffusion calculations show that a finite crack extension at a high crack tip velocity is necessary to initiate EAC, providing a possible explanation for the lack of high crack growth observations reported in low alloy steels in structural applications involving low oxygen environments.

  1. Performance of Alumina-Forming Austenitic Steels, Fe-base and Ni-base alloys exposed to metal dusting environments

    SciTech Connect

    Vande Put Ep Rouaix, Aurelie; Unocic, Kinga A; Pint, Bruce A; Brady, Michael P

    2011-01-01

    A series of conventional Fe- and Ni- base, chromia- and alumina- forming alloys, and a newly developed creep-resistant, alumina-forming austenitic steel were developed and its performance relative to conventional Fe- and Ni-based chromia-forming alloys was evaluated in metal dusting environments with a range of water vapor contents. Five 500h experiments have been performed at 650 C with different water vapor contents and total pressures. Without water vapor, the Ni-base alloys showed greater resistance to metal dusting than the Fe-base alloys, including AFA. However, with 10-28% water vapor, more protective behavior was observed with the higher-alloyed materials and only small mass changes were observed. Longer exposure times are in progress to further differentiate performance.

  2. Chemical elements diffusion in the stainless steel components brazed with Cu-Ag alloy

    NASA Astrophysics Data System (ADS)

    Voiculescu, I.; Geanta, V.; Vasile, I. M.; Binchiciu, E. F.; Winestoock, R.

    2016-06-01

    The paper presents the study of diffusion of chemical elements through a brazing joint, between two thin components (0.5mm) made of stainless steel 304. An experimental brazing filler material has been used for brazing stainless steel component and then the diffusion phenomenon has been studied, in terms of chemical element displacement from the brazed separation interface. The filler material is in the form of a metal rod coated with ceramic slurry mixture of minerals, containing precursors and metallic powders, which can contribute to the formation of deposit brazed. In determining the distance of diffusion of chemical elements, on both sides of the fusion line, were performed measurements of the chemical composition using electron microscopy SEM and EDX spectrometry. Metallographic analysis of cross sections was performed with the aim of highlight the microstructural characteristics of brazed joints, for estimate the wetting capacity, adherence of filler metal and highlight any imperfections. Analyzes performed showed the penetration of alloying elements from the solder (Ag, Cu, Zn and Sn) towards the base material (stainless steel), over distances up to 60 microns.

  3. Low-Temperature Toughening Mechanism in Thermomechanically Processed High-Strength Low-Alloy Steels

    NASA Astrophysics Data System (ADS)

    Hwang, Byoungchul; Lee, Chang Gil; Kim, Sung-Joon

    2011-03-01

    High-strength low-alloy (HSLA) steels were fabricated by varying thermomechanical processing conditions such as rolling and cooling conditions in the intercritical region, and the low-temperature toughening mechanism was investigated in terms of microstructure and the associated grain boundary characteristics. The steels acceleratedly cooled to relatively higher temperature had lower tensile strength than those acceleratedly cooled to room temperature due to the increased volume fraction of granular bainite or polygonal ferrite (PF) irrespective of rolling in the intercritical region, while the yield strength was dependent on intercritical rolling, and start and finish cooling temperatures, which affected the formation of PF and low-temperature transformation phases. The steel rolled in the intercritical region and cooled to 673 K (400 °C) provided the best combination of high yield strength and excellent low-temperature toughness because of the presence of fine PF and appropriate mixture of various low-temperature transformation phases such as granular bainite, degenerate upper bainite (DUB), lower bainite (LB), and lath martensite (LM). Despite the high yield strength, the improvement of low-temperature toughness could be explained by the reduction of overall effective grain size based on the electron backscattered diffraction (EBSD) analysis data, leading to the decrease in ductile-to-brittle transition temperature (DBTT).

  4. Ab initio study of the phase stability in paramagnetic duplex steel alloys

    NASA Astrophysics Data System (ADS)

    Pitkänen, H.; Alatalo, M.; Puisto, A.; Ropo, M.; Kokko, K.; Punkkinen, M. P. J.; Olsson, P.; Johansson, B.; Hertzman, S.; Vitos, L.

    2009-01-01

    Duplex stainless steels have many superior properties compared to conventional steels, this being mainly due to their microstructure containing approximately equal amount of ferrite and austenite phases formed by iron, chromium (or Cr equivalent), and nickel (or Ni equivalent). Using computational methods based on first-principles theories, the phase stability of paramagnetic Fe1-c-nCrcNin alloys ( 0.12≤c≤0.32 and 0.04≤n≤0.32 ) at high temperatures (≳1000K) is addressed. It is shown that the stabilization of the ferrite-austenite two-phase field in duplex steels is a result of complex interplay of several competing phenomena. Taking into account only the formation energies yields a complete phase separation, strongly overestimating the two-phase region. The formation energies are calculated to be lower for the austenite than for the ferrite, meaning that the configurational entropy has a more significant impact on the stability field of the austenitic phase. The magnetic and vibrational free energies have opposite effects on the phase stability. Namely, the magnetic entropy favors the ferrite phase, whereas the vibrational free energy stabilizes the austenite phase. Combining the formation energies with the magnetic, vibrational, and configurational free energies, a region of coexistence between the two phases is obtained, in line with former thermodynamic assessments as well as with experimental observations.

  5. Effects of LWR coolant environments on fatigue design curves of carbon and low-alloy steels

    SciTech Connect

    Chopra, O.K.; Shack, W.J.

    1998-03-01

    The ASME Boiler and Pressure Vessel Code provides rules for the construction of nuclear power plant components. Figures I-9.1 through I-9.6 of Appendix I to Section III of the code specify fatigue design curves for structural materials. While effects of reactor coolant environments are not explicitly addressed by the design curves, test data indicate that the Code fatigue curves may not always be adequate in coolant environments. This report summarizes work performed by Argonne National Laboratory on fatigue of carbon and low-alloy steels in light water reactor (LWR) environments. The existing fatigue S-N data have been evaluated to establish the effects of various material and loading variables such as steel type, dissolved oxygen level, strain range, strain rate, temperature, orientation, and sulfur content on the fatigue life of these steels. Statistical models have been developed for estimating the fatigue S-N curves as a function of material, loading, and environmental variables. The results have been used to estimate the probability of fatigue cracking of reactor components. The different methods for incorporating the effects of LWR coolant environments on the ASME Code fatigue design curves are presented.

  6. Effect of microstructure on transformation-induced plasticity of silicon-containing low-alloy steel

    SciTech Connect

    Tomita, Yoshiyuki; Morioka, Kojiro

    1997-04-01

    Fe-0.6C-1.5Si-0.8Mn steel was studied to determine the effect of the microstructure on transformation-induced plasticity (TRIP) of silicon-containing low-alloy steel. A remarkable increase in elongation through TRIP can develop in the steel subjected to the following heat treatments: (1) austemper combined with subcritical annealing (SA Aus-T): subcritical annealing at 993K followed by austempering at 673K and then light tempering (after austenitization at 1173K); (2) austemper coupled with interrupted quenching (IQ Aus-T): interrupted quenching at 533K followed by austempering at 673K and light tempering (after austenization at 1,173K). The SA Aus-T treatment produced the triple structures of carbide-free upper bainite, retained austenite ({gamma}R), and free ferrite. As a result of the IQ Aus-T treatment, the triple structures of carbide-free upper bainite, {gamma}R, and tempered martensite appeared. The results are described and microstructural factors in TRIP are discussed.

  7. Infrared repair brazing of 403 stainless steel with a nickel-based braze alloy

    NASA Astrophysics Data System (ADS)

    Shiue, R. K.; Wu, S. K.; Hung, C. M.

    2002-06-01

    Martensitic stainless steel (403SS) is extensively used for intermediate and low-pressure steam turbine blades in fossil-fuel power plants. The purpose of this investigation is to study the repair of shallow cracks on the surface of 403SS steam turbine blades by infrared repair brazing using rapid thermal cycles. A nickel-based braze alloy (NICROBRAZ LM) is used as filler metal. The braze alloy after brazing is primarily comprised of borides and an FeNi3 matrix with different amounts of alloying elements, especially B and Si. As the brazing temperature increases, more Fe atoms are dissolved into the molten braze. Some boron atoms diffuse into the 403SS substrate primarily via grain boundary diffusion and form B-Cr-Fe intermetallic precipitates along the grain boundaries. The LM filler metal demonstrates better performance than 403SS in both microhardness and wear tests. It is also noted that specimens brazed in a vacuum have less porosity than those brazed in an Ar atmosphere. The shear strength of the joint is around 300 MPa except for specimens brazed in short time periods, e.g., 5 seconds in Ar flow and 30 seconds in vacuum. The fractographs mainly consist of brittle fractures and no ductile dimple fractures observed in the scanning electron microscope (SEM) examination.

  8. Effect of superheat on macrostructure and macrosegregation in continuous cast low-alloy steel slabs

    NASA Astrophysics Data System (ADS)

    Pikkarainen, T.; Vuorenmaa, V.; Rentola, I.; Leinonen, M.; Porter, D.

    2016-03-01

    The effect of superheat on grain sedimentation and macrosegregation has been investigated using experimental castings of a low-alloyed steel grade. With a high superheat of ∼ 40 °C, the central equiaxed parts of the slabs consisted of randomly oriented fine dendrites but with a low superheat of ∼ 10 °C, coarse globular structures formed. The mean carbon content measured with optical emission spectroscopy was of the order of 15% smaller with coarse globular structures than in fine equiaxed dendritic structures. Electron probe microanalysis of other alloying elements indicates that the negative segregation in the slab central zones is caused by sedimentation of globulites. With superheat in the range ∼ 20 - 40 °C, the equiaxed zone is bordered by a columnar to equiaxed transition (CET) zone. In this region a positive macrosegregation of carbon and other alloying elements was observed. These phenomena are important when considering the through-thickness properties of the slabs and final products.

  9. Quantitative observations of hydrogen-induced, slow crack growth in a low alloy steel

    NASA Technical Reports Server (NTRS)

    Nelson, H. G.; Williams, D. P.

    1973-01-01

    Hydrogen-induced slow crack growth, da/dt, was studied in AISI-SAE 4130 low alloy steel in gaseous hydrogen and distilled water environments as a function of applied stress intensity, K, at various temperatures, hydrogen pressures, and alloy strength levels. At low values of K, da/dt was found to exhibit a strong exponential K dependence (Stage 1 growth) in both hydrogen and water. At intermediate values of K, da/dt exhibited a small but finite K dependence (Stage 2), with the Stage 2 slope being greater in hydrogen than in water. In hydrogen, at a constant K, (da/dt) sub 2 varied inversely with alloy strength level and varied essentially in the same complex manner with temperature and hydrogen pressure as noted previously. The results of this study provide support for most of the qualitative predictions of the lattice decohesion theory as recently modified by Oriani. The lack of quantitative agreement between data and theory and the inability of theory to explain the observed pressure dependence of slow crack growth are mentioned and possible rationalizations to account for these differences are presented.

  10. Fabrication of Fe-Cr-Mo powder metallurgy steel via a mechanical-alloying process

    NASA Astrophysics Data System (ADS)

    Park, Jooyoung; Jeong, Gowoon; Kang, Singon; Lee, Seok-Jae; Choi, Hyunjoo

    2015-11-01

    In this study, we employed a mechanical-alloying process to manufacture low-alloy CrL and CrM steel powders that have similar specifications to their water-atomized counterparts. X-ray diffraction showed that Mo and Cr are alloyed in Fe after four cycles of planetary milling for 1 h at 150 RPM with 15-min pauses between the cycles (designated as P2C4 process). Furthermore, the measured powder size was found to be similar to that of the water-atomized counterparts according to both scanning electron microscope images and laser particle size analysis. The samples were sintered at 1120 °C, after which the P2C4-milled CrL showed similar hardness to that of water-atomized CrL, whereas the P2C4-milled CrM showed about 45% lower hardness than that of its water-atomized counterpart. Water-atomized CrM consists of a well-developed lathtype microstructure (bainite or martensite), while a higher fraction of polygonal ferrite is observed in P2C4-milled CrM. This phase difference causes the reduction of hardness in the P2C4-milled CrM, implying that the phase transformation behavior of specimens produced via powder metallurgy is influenced by the powder fabrication method.

  11. 78 FR 48647 - Certain Circular Welded Non-Alloy Steel Pipe from Mexico: Preliminary Results and Partial...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-09

    ... International Trade Administration Certain Circular Welded Non-Alloy Steel Pipe from Mexico: Preliminary Results... Administration, International Trade Administration, Department of Commerce. SUMMARY: In response to requests by.... FOR FURTHER INFORMATION CONTACT: Mark Flessner or Robert James, AD/CVD Operations, Office 7,...

  12. 77 FR 34344 - Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Final Results of the Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-11

    ... International Trade Administration Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Final Results of the Antidumping Duty Administrative Review AGENCY: Import Administration, International Trade..., International Trade ] Administration, U.S. Department of Commerce, 14th Street and Constitution Avenue...

  13. Flight Planning for the International Space Station-Levitation Observation of Dendrite Evolution in Steel Ternary Alloy Rapid Solidification

    NASA Technical Reports Server (NTRS)

    Flemings, M. C.; Matson, D. M.; Loser, W.; Hyers, R. W.; Rogers, J. R.; Curreri, Peter A. (Technical Monitor)

    2002-01-01

    The paper is an overview of the status and science for the LODESTARS (Levitation Observation of Dendrite Evolution in Steel Ternary Alloy Rapid Solidification) research project. The program is aimed at understanding how melt convection influences phase selection and the evolution of rapid solidification microstructures.

  14. 75 FR 13255 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-19

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe..., line, and pressure pipe (``seamless pipe'') from the People's Republic of China (``PRC'') with the... Pressure Pipe From the People's Republic of China: Initiation of Antidumping Duty Investigation, 74...

  15. The design of an Fe-12Mn-O.2Ti alloy steel for low temperature use

    NASA Technical Reports Server (NTRS)

    Hwang, S. K.; Morris, J. W., Jr.

    1977-01-01

    An investigation was made to improve the low temperature mechanical properties of Fe-8 approximately 12% Mn-O 2Ti alloy steels. A two-phase(alpha + gamma) tempering in combination with cold working or hot working was identified as an effective treatment. A potential application as a Ni-free cryogenic steel was shown for this alloy. It was also shown that an Fe-8Mn steel could be grain-refined by a purely thermal treatment because of its dislocated martensitic structure and absence of epsilon phase. A significant reduction of the ductile-brittle transition temperature was obtained in this alloy. The nature and origin of brittle fracture in Fe-Mn alloys were also investigated. Two embrittling regions were found in a cooling curve of an Fe-12Mn-O 2Ti steel which was shown to be responsible for intergranular fracture. Auger electron spectroscopy identified no segregation during solution-annealing treatment. Avoiding the embrittling zones by controlled cooling led to a high cryogenic toughness in a solution-annealed condition.

  16. Surface and cut-edge corrosion behavior of Zn-Mg-Al alloy-coated steel sheets as a function of the alloy coating microstructure

    NASA Astrophysics Data System (ADS)

    Oh, Min-Suk; Kim, Sang-Heon; Kim, Jong-Sang; Lee, Jae-Won; Shon, Je-Ha; Jin, Young-Sool

    2016-01-01

    The effects of Mg and Al content on the microstructure and corrosion resistance of hot-dip Zn-Mg-Al alloycoated steel sheets were investigated. Pure Zn and Zn-based alloy coatings containing Mg (0-5 wt%) and Al (0.2-55 wt%) were produced by a hot-dip galvanizing method. Mg and Al addition induced formation of intermetallic microstructures, like primary Zn, Zn/MgZn2 binary eutectic, dendric Zn/Al eutectoid, and Zn/Al/MgZn2/ternary eutectic structures in the coating layer. MgZn2-related structures (Zn/MgZn2, Zn/Al/MgZn2, MgZn2) played an important role in increasing the corrosion resistance of Zn-Mg-Al alloy-coated steel sheets. Zn-3%Mg-2.5%Al coating layer containing a large volume of lamellar-shaped Zn/MgZn2 binary eutectic structures showed the best cut-edge corrosion resistance. The analysis indicated that Mg dissolved from MgZn2 in the early stage of corrosion and migrated to the cathodic region of steel-exposed cut-edge area to form dense and ordered protective corrosion products, leading to prolonged cathodic protection of Zn-Mg-Al alloy-coated steel sheets.

  17. A comparative evaluation of welding consumables for dissimilar weids between 316LN austenitic stainless steel and Alloy 800

    NASA Astrophysics Data System (ADS)

    Sireesha, M.; Albert, Shaju K.; Shankar, V.; Sundaresan, S.

    2000-03-01

    Transition joints in power plants between ferritic steels and austenitic stainless steels suffer from a mismatch in coefficients of thermal expansion (CTE) and the migration of carbon during service from the ferritic to the austenitic steel. To overcome these, nickel-based consumables are commonly used. The use of a trimetallic combination with an insert piece of intermediate CTE provides for a more effective lowering of thermal stresses. The current work envisages a trimetallic joint involving modified 9Cr-1Mo steel and 316LN austenitic stainless steel as the base materials and Alloy 800 as the intermediate piece. Of the two joints involved, this paper describes the choice of welding consumables for the joint between Alloy 800 and 316LN. Four consumables were examined: 316, 16-8-2, Inconel 82 and Inconel 182. The comparative evaluation was based on hot cracking tests and estimation of mechanical properties and coefficient of thermal expansion. While 16-8-2 exhibited highest resistance to solidification cracking, the Inconel filler materials also showed adequate resistance; additionally, the latter were superior from the mechanical property and coefficient of thermal expansion view-points. It is therefore concluded that for the joint between Alloy 800 and 316LN the Inconel filler materials offer the best compromise.

  18. Pack cementation Cr-Al coating of steels and Ge-doped silicide coating of Cr-Nb alloy

    SciTech Connect

    He, Y.R.; Zheng, M.H.; Rapp, R.A.

    1995-08-01

    Carbon steels or low-alloy steels used in utility boilers, heat exchangers, petrochemical plants and coal gasification systems are subjected to high temperature corrosion attack such as oxidation, sulfidation and hot corrosion. The pack cementation coating process has proven to be an economical and effective method to enhance the corrosion resistance by modifying the surface composition of steels. With the aid of a computer program, STEPSOL, pack cementation conditions to produce a ferrite Cr-Al diffusion coating on carbon-containing steels by using elemental Cr and Al powders have been calculated and experimentally verified. The cyclic oxidation kinetics for the Cr-Al coated steels are presented. Chromium silicide can maintain high oxidation resistance up to 1100{degrees}C by forming a SiO{sub 2} protective scale. Previous studies at Ohio State University have shown that the cyclic oxidation resistance of MOSi{sub 2} and TiSi{sub 2} can be further improved by Ge addition introduced during coating growth. The halide-activated pack cementation process was modified to produce a Ge-doped silicide diffusion coating in a single processing step for the ORNL-developed Cr-Nb advanced intermetallic alloy. The oxidation behavior of the silicide-coated Cr-Nb alloy was excellent: weight gain of about 1 mg/cm{sup 2} upon oxidation at 1100{degrees}C in air for 100 hours.

  19. Tribological Behavior of Babbitt Alloy Rubbing Against Si3N4 and Steel Under Dry Friction Condition

    NASA Astrophysics Data System (ADS)

    Ji, Xianbing; Chen, Yinxia

    2016-03-01

    The tribological behavior of Babbitt alloy rubbing with Si3N4 ball and steel ball with various sliding speeds at dry friction condition was investigated. It was found that B88 alloy rubbing with Si3N4 ball and steel ball possesses a low sliding wear resistance at dry friction. The wear rate is above 10-4 mm3/Nm, and the friction coefficient is from 0.2 to 0.4. At low sliding speed of 0.05-0.1 m/s, the mainly wear mechanisms are microgroove and fatigue wear, while at high sliding speed of 0.5 m/s, the wear mechanisms depend on plastic deformation and delamination. The high wear rate indicates that it is needed to prevent Babbitt alloy from working at dry friction conditions, while the low friction coefficient suggests that it is not easy to the occurrence of cold weld.

  20. Cessation of environmentally-assisted cracking in a low-alloy steel: Theoretical analysis

    SciTech Connect

    Wire, G.L.

    1997-02-01

    Environmentally Assisted Cracking (EAC) can cause increases in fatigue crack growth rates of 40 to 100 times the rate in air for low alloy steels. The increased rates can lead to very large predicted crack growth. EAC is activated by a critical level of dissolved sulfides at the crack tip. Sulfide inclusions (MnS) in the steel produce corrosive sulfides in solution following exposure by a growing crack. In stagnant, low oxygen water conditions considered here, diffusion is the dominant mass transport mechanism acting to change the sulfide concentration within the crack. The average crack tip velocity is below the level required to produce the critical crack tip sulfide ion concentration required for EAC. Crack extension analyses also consider the breakthrough of large, hypothetical embedded defects with the attendant large freshly exposed sulfide inventory. Combrade et al. noted that a large inventory of undissolved metallurgical sulfides on crack flanks could trigger EAC, but did not quantify the effects. Diffusion analysis is extended herein to cover breakthrough of embedded defects with large sulfide inventories. The mass transport via diffusion is limited by the sulfide solubility. As a result, deep cracks in high sulfur steels are predicted to retain undissolved sulfides for extended but finite periods of time t{sub diss} which increase with the crack length and the metallurgical sulfide content in the steel. The analysis shows that the duration of EAC is limited to t{sub diss} providing V{sub eac}, the crack tip velocity associated with EAC is less than V{sub In}, the crack tip velocity below which EAC will not occur in an initially sulfide free crack. This condition on V{sub eac} need only be met for a short time following crack cleanup to turn off EAC. The predicted crack extension due to limited duration of EAC is a small fraction of the initial embedded defect size and would not greatly change calculated crack depths.

  1. Irradiation damage behavior of low alloy steel wrought and weld materials

    SciTech Connect

    Stofanak, R.J.; Poskie, T.J.; Li, Y.Y.; Wire, G.L.

    1993-10-01

    A study was undertaken to evaluate the irradiation damage response of several different types of low alloy steel: vintage type ASTM A302 Grade B (A302B) plates and welds containing different Ni and Cu concentrations, 3.5% Ni steels similar to ASTM A508 Class 4, welds containing about 1% Ni (similar to type 105S), and 3.5% Ni steels with ``superclean`` composition. All materials were irradiated at several different irradiation damage levels ranging from 0.0003 to 0.06 dpa at 232C (450F). Complete Charpy V-notch impact energy transition temperature curves were generated for all materials before and after irradiation to determine transition temperature at 4IJ (30 ft-lb) or 47J (35 ft-lb) and the upper shelf energy. Irradiation damage behavior was measured by shift in Charpy 41J or 47J transition temperature ({Delta}TT4{sub 41J} or {Delta}TT{sub 47J}) and lowering of upper shelf Charpy energy at a given irradiation damage level. It was found that chemical composition greatly influenced irradiation damage behavior; highest irradiation damage (greatest {Delta}TT) was found in an A302B type weld containing 1.28% Ni and 0.20% Cu while the least damage was found in 3.5% Ni, 0.05% Cu, superclean wrought materials. Combination of Ni and Cu was found to affect irradiation damage behavior at higher irradiation damage levels in the A302B welds where the 1.28% Ni, 0.20% Cu weld showed more damage than a 0.60% Ni, 0.31% Cu weld. For the 3.5% Ni steels, fabrication influenced irradiation behavior in that a silicon (Si) killed material showed greater irradiation damage than a low silicon material. In general, the 3.5% Ni materials with low copper showed less irradiation damage than the A302B materials.

  2. Evaluation of Stress Corrosion Cracking Susceptibility Using Fracture Mechanics Techniques, Part 1. [environmental tests of aluminum alloys, stainless steels, and titanium alloys

    NASA Technical Reports Server (NTRS)

    Sprowls, D. O.; Shumaker, M. B.; Walsh, J. D.; Coursen, J. W.

    1973-01-01

    Stress corrosion cracking (SSC) tests were performed on 13 aluminum alloys, 13 precipitation hardening stainless steels, and two titanium 6Al-4V alloy forgings to compare fracture mechanics techniques with the conventional smooth specimen procedures. Commercially fabricated plate and rolled or forged bars 2 to 2.5-in. thick were tested. Exposures were conducted outdoors in a seacoast atmosphere and in an inland industrial atmosphere to relate the accelerated tests with service type environments. With the fracture mechanics technique tests were made chiefly on bolt loaded fatigue precracked compact tension specimens of the type used for plane-strain fracture toughness tests. Additional tests of the aluminum alloy were performed on ring loaded compact tension specimens and on bolt loaded double cantilever beams. For the smooth specimen procedure 0.125-in. dia. tensile specimens were loaded axially in constant deformation type frames. For both aluminum and steel alloys comparative SCC growth rates obtained from tests of precracked specimens provide an additional useful characterization of the SCC behavior of an alloy.

  3. Hydrogen adsorption and diffusion, and subcritical-crack growth in high-strength steels and nickel base alloys

    NASA Technical Reports Server (NTRS)

    Wei, R. P.; Klier, K.; Simmons, G. W.

    1974-01-01

    Coordinated studies of the kinetics of crack growth and of hydrogen adsorption and diffusion were initiated to develop information that is needed for a clearer determination of the rate controlling process and possible mechanism for hydrogen enhanced crack growth, and for estimating behavior over a range of temperatures and pressures. Inconel 718 alloy and 18Ni(200) maraging steel were selected for these studies. 18Ni(250) maraging steel, 316 stainless steel, and iron single crystal of (111) orientation were also included in the chemistry studies. Crack growth data on 18Ni(250) maraging steel from another program are included for comparison. No sustained-load crack growth was observed for the Inconel 718 alloy in gaseous hydrogen. Gaseous hydrogen assisted crack growth in the 18Ni maraging steels were characterized by K-independent (Stage 2) extension over a wide range of hydrogen pressures (86 to 2000 torr or 12 kN/m2 to 266 kN/m2) and test temperatures (-60 C to +100 C). The higher strength 18Ni(250) maraging steel was more susceptible than the lower strength 200 grade. A transition temperature was observed, above which crack growth rates became diminishingly small.

  4. A comparative study of the in vitro corrosion behavior and cytotoxicity of a superferritic stainless steel, a Ti-13Nb-13Zr alloy, and an austenitic stainless steel in Hank's solution.

    PubMed

    Assis, S L; Rogero, S O; Antunes, R A; Padilha, A F; Costa, I

    2005-04-01

    In this study, the in vitro corrosion resistance of a superferritic stainless steel in naturally aerated Hank's solution at 37 degrees C has been determined to evaluate the steel for use as a biomaterial. The potentiodynamic polarization method and electrochemical impedance spectroscopy (EIS) were used to determine the corrosion resistance. The polarization results showed very low current densities at the corrosion potential and electrochemical behavior typical of passive metals. At potentials above 0.75 V (SCE), and up to that of the oxygen evolution reaction, the superferritic steel exhibited transpassive behavior followed by secondary passivation. The superferritic stainless steel exhibited high pitting resistance in Hank's solution. This steel did not reveal pits even after polarization to 3000 mV (SCE). The EIS results indicated high impedance values at low frequencies, supporting the results obtained from the polarization measurements. The results obtained for the superferritic steel have been compared with those of the Ti-13Nb-13Zr alloy and an austenitic stainless steel, as Ti alloys are well known for their high corrosion resistance and biocompatibility, and the austenitic stainless steel is widely used as an implant material. The cytotoxicity tests indicated that the superferritic steel, the austenitic steel, and the Ti-13Nb-13Zr alloy were not toxic. Based on corrosion resistance and cytotoxicity results, the superferritic stainless steel can be considered as a potential biomaterial.

  5. Release of nickel ions from stainless steel alloys used in dental braces and their patch test reactivity in nickel-sensitive individuals.

    PubMed

    Jensen, Christian Stab; Lisby, Steen; Baadsgaard, Ole; Byrialsen, Kirsten; Menné, Torkil

    2003-06-01

    Nickel ions leached in sufficient quantities from nickel-containing alloys may induce nickel sensitization or elicit allergic contact dermatitis. Nickel-containing stainless steel alloys are generally considered safe for nickel-sensitive individuals to use. The study summarized in this paper investigated 3 parameters. First, the release of nickel was estimated in artificial saliva and sweat from 4 different stainless steel alloys frequently used in dental braces. Second, in a pilot study, oral mucosa cells harvested from 3 dental patients before and after the attachment of dental braces were analysed for possible nickel content. Third, patch test reactivity of the 4 stainless steel alloys was tested on 31 nickel-sensitive subjects. All 4 stainless steel alloys released small amounts of nickel ions into artificial saliva (<0.13 micro g/cm2/week) and artificial sweat (<0.05 micro g/cm2/week), but no measurable amounts of nickel were found in any of the oral mucosa samples. None of the 31 nickel-sensitive subjects reacted to patch testing with the 4 stainless steel alloys, indicating that these stainless steel alloys would be safe to use in direct and prolonged contact with the skin.

  6. Development of brazing foils to join monocrystalline tungsten alloys with ODS-EUROFER steel

    NASA Astrophysics Data System (ADS)

    Kalin, B. A.; Fedotov, V. T.; Sevrjukov, O. N.; Kalashnikov, A. N.; Suchkov, A. N.; Moeslang, A.; Rohde, M.

    2007-08-01

    Results on rapidly solidified filler metals for brazing W with W and monocrystalline W with EUROFER steel (FS) are presented. Rapidly quenched powder-type filler metals based on Ti bal-V-Cr-Be were developed to braze polycrystalline W with monocrystalline W. In addition, Fe bal-Ta-Ge-Si-B-Pd alloys were developed to braze monocrystalline W with FS for helium gas cooled divertors and plasma-facing components. The W to FS brazed joints were fabricated under vacuum at 1150 °C, using a Ta spacer of 0.1 mm in thickness to account for the different thermal expansions. The monocrystalline tungsten as well as the related brazed joints withstood 30 cycles between 750 °C/20 min and air cooling/3-5 min.

  7. LITERATURE SURVEY OF GASEOUS HYDROGEN EFFECTS ON THE MECHANICAL PROPERTIES OF CARBON AND LOW ALLOY STEELS

    SciTech Connect

    Lam, P; Robert Sindelar, R; Thad Adams, T

    2007-04-18

    Literature survey has been performed for a compendium of mechanical properties of carbon and low alloy steels following hydrogen exposure. The property sets include yield strength, ultimate tensile strength, uniform elongation, reduction of area, threshold stress intensity factor, fracture toughness, and fatigue crack growth. These properties are drawn from literature sources under a variety of test methods and conditions. However, the collection of literature data is by no means complete, but the diversity of data and dependency of results in test method is sufficient to warrant a design and implementation of a thorough test program. The program would be needed to enable a defensible demonstration of structural integrity of a pressurized hydrogen system. It is essential that the environmental variables be well-defined (e.g., the applicable hydrogen gas pressure range and the test strain rate) and the specimen preparation be realistically consistent (such as the techniques to charge hydrogen and to maintain the hydrogen concentration in the specimens).

  8. Special Features of Fracture of a Solid-State Titanium Alloy - Nickel - Stainless Steel Joint

    NASA Astrophysics Data System (ADS)

    Khazgaliev, R. G.; Mukhametrakhimov, M. Kh.; Imaev, M. F.; Shayakhmetov, R. U.; Mulyukov, R. R.

    2015-10-01

    Microstructure, nanohardness, and special features of fracture of three-phase titanium alloy and stainless steel joint through a nanostructural nickel foil are investigated. Uniformly distributed microcracks are observed in Ti2Ni and TiN3 layers joined at temperatures above T = 700°C, whereas no microcracks are observed in the TiNi layer. This suggests that the reason for microcracking is an anomalously large change in the linear expansion coefficient of the TiNi layer during austenitic-martensitic transformation. Specimens subjected to mechanical tests at T = 20°C are fractured along different layers of the material, namely, in the central part of the specimen they are fractured along the Ti2Тi/TiNi interface, whereas at the edge they are fractured along the TiNi/TiNi3 interface.

  9. Status of ATR-A1 irradiation experiment on vanadium alloys and low-activation steels

    SciTech Connect

    Tsai, H.; Strain, R.V.; Gomes, I.; Smith, D.L.; Matsui, H.

    1996-10-01

    The ATR-A1 irradiation experiment was a collaborative U.S./Japan effort to study at low temperature the effects of neutron damage on vanadium alloys. The experiment also contained a limited quantity of low-activation ferritic steel specimens from Japan as part of the collaboration agreement. The irradiation started in the Advanced Test Reactor (ATR) on November 30, 1995, and ended as planned on May 5, 1996. Total exposure was 132.9 effective full power days (EFPDs) and estimated neutron damage in the vanadium was 4.7 dpa. The vehicle has been discharged from the ATR core and is scheduled to be disassembled in the next reporting period.

  10. Direct Metal Deposition of H13 Tool Steel on Copper Alloy Substrate: Parametric Investigation

    NASA Astrophysics Data System (ADS)

    Imran, M. Khalid; Masood, S. H.; Brandt, Milan

    2015-12-01

    Over the past decade, researchers have demonstrated interest in tribology and prototyping by the laser aided material deposition process. Laser aided direct metal deposition (DMD) enables the formation of a uniform clad by melting the powder to form desired component from metal powder materials. In this research H13 tool steel has been used to clad on a copper alloy substrate using DMD. The effects of laser parameters on the quality of DMD deposited clad have been investigated and acceptable processing parameters have been determined largely through trial-and-error approaches. The relationships between DMD process parameters and the product characteristics such as porosity, micro-cracks and microhardness have been analysed using scanning electron microscope (SEM), image analysis software (ImageJ) and microhardness tester. It has been found that DMD parameters such as laser power, powder mass flow rate, feed rate and focus size have an important role in clad quality and crack formation.

  11. Morphology, Structure, and Chemistry of Nanoclusters in a Mechanically-Alloyed Nanostructured Ferritic Steel

    SciTech Connect

    Brandes, Matthew C; Kovarik, L.; Miller, Michael K; Mills, Michael J.

    2012-01-01

    Nanostructured ferritic steels have excellent elevated temperature strengths, creep resistances, and radiation tolerances due to the presence of a high density of Ti-Y-O-enriched nanoclusters. The compositions, morphologies, and structures of the smallest of these nanoclusters with maximum dimensions of {approx}2-4 nm were investigated in alloy 14YWT by high-resolution scanning transmission electron microscopy and atom probe tomography. Nanoclusters are found to be coherent with truncated rhombic dodecahedron morphologies defined by the {l_brace}100{r_brace} and {l_brace}110{r_brace} planes in the Fe matrix. Particles have compositions rich in Ti, O, Y, and Cr that are inconsistent with known oxide structures. The smallest nanoclusters appear to lack an identifiable crystal structure. Both nano-diffraction and focal series imaging through the sample thickness suggest that they are amorphous.

  12. Study of Different Vacuum Heat Treatments on the Strength of a Low Alloyed Sintered Steel

    NASA Astrophysics Data System (ADS)

    Bidulský, Róbert; Grande, Marco Actis; Bidulská, Jana; Kvačkaj, Tibor

    2011-06-01

    The present paper deals with the evaluation of different vacuum heat treatments on the microstructure of a low alloyed sintered Fe-[1.5 Cr-0.2 Mo]-0.6 C steel. Different gas pressures were applied on the material during cooling from the sintering temperature. The average cooling rates were calculated in the range of 1453 K to 673 K and were varying from 0.1 to 6 K/s, according to the gas pressure applied (0 to 600 kPa). Mechanical properties have been evaluated in terms of toughness, plasticity and hardness. The results show that increasing the nitrogen pressure resulted in an increased amount of bainite/martensite microstructure with high level of properties achieved.

  13. Iodine sorption/desorption from low-alloy steel and graphite. Draft

    SciTech Connect

    Wichner, R.P.; Osborne, M.F.; Lorenz, R.A.; Briggs, R.B.

    1980-01-01

    Tests have been performed at Oak Ridge National Laboratory on the sorptive behavior of iodine on two prominent HTGR primary circuit materials - type H-451 graphite, which is the selected core graphite, and a low-alloy steel (T-22), a type which is employed in the lower temperature regions of the primary system. The main emphasis of the work is the determination of equilibrium sorptive capacities for very low iodine partial pressures. Toward this goal, the test procedures allow on-line determination of sorptive capacity down to iodine partial pressures of approx. 10/sup -11/ bar in helium at a total pressure of 1 atm. The apparatus employed is of the helium flow-through type. Detectors monitor the degree of sorption on specimens and traps, which, together with the helium flowrate and source vapor pressure, yield a continuous determination of iodine mass transport.

  14. Oxidation Characteristics of Fe–18Cr–18Mn-Stainless Steel Alloys

    SciTech Connect

    Rawers, James

    2010-10-01

    Air oxidation studies of Fe-18Cr-18Mn stainless steels were conducted at 525°C, 625°C, and 725°C. Alloys were evaluated with respect to changes in oxidation properties as a result of interstitial additions of nitrogen and carbon and of minor solute additions of silicon, molybdenum, and nickel. Interstitial concentrations possibly had a small, positive effect on oxidation resistance. Minor solute additions significantly improved oxidation resistance but could also reduce interstitial solubility resulting in formation of chromium carbides. Loss of solute chromium resulted in a slight reduction in oxidation protection. Oxidation lasting over 500 hours produced a manganese rich, duplex oxide structure: an outer sesquioxide and an inner spinel oxide.

  15. LITERATURE SURVEY OF GASEOUS HYDROGEN EFFECTS ON THE MECHANICAL PROPERTIES OF CARBON AND LOW ALLOY STEELS

    SciTech Connect

    Lam, P; Andrew Duncan, A; Robert Sindelar, R; Thad Adams, T

    2009-04-27

    Literature survey has been performed for a compendium of mechanical properties of carbon and low alloy steels following hydrogen exposure. The property sets include yield strength, ultimate tensile strength, uniform elongation, reduction of area, threshold stress intensity factor, fracture toughness, and fatigue crack growth. These properties are drawn from literature sources under a variety of test methods and conditions. However, the collection of literature data is by no means complete, but the diversity of data and dependency of results in test method is sufficient to warrant a design and implementation of a thorough test program. The program would be needed to enable a defensible demonstration of structural integrity of a pressurized hydrogen system. It is essential that the environmental variables be well-defined (e.g., the applicable hydrogen gas pressure range and the test strain rate) and the specimen preparation be realistically consistent (such as the techniques to charge hydrogen and to maintain the hydrogen concentration in the specimens).

  16. Alloy design to control the size and morphology of niobium carbides in tool steels

    SciTech Connect

    Pereira, M.M.; Andrade, M.S. , Belo Horizonte, MG ); Guimaraes, J.R.C. )

    1989-09-01

    Controlling the size and the morphology of niobium carbides is crucial to develop a carbide volume fraction capable of significantly influencing the cutting/wear properties of tool steels and cast irons. The phase diagram suggests that by increasing the delta phase field, ferrite may be forced to precipitate preferentially to NbC. Hence, alloying with a strong ferritizer such as aluminum and/or silicon may result in more convenient microstructure when Nb %{gt}3. To check that possibility, as-cast microstructures were analyzed by optical and scanning electron microscopy. By combining additions of niobium and aluminum, it seems possible to control the size and the morphology of niobium carbides without necessarily resorting to more complex processes such as atomization and the like.

  17. The influence of the corrosion product layer generated on the high strength low-alloy steels welded by underwater wet welding with stainless steel electrodes in seawater

    NASA Astrophysics Data System (ADS)

    Bai, Qiang; Zou, Yan; Kong, Xiangfeng; Gao, Yang; Dong, Sheng; Zhang, Wei

    2017-02-01

    The high strength low-alloy steels are welded by underwater wet welding with stainless steel electrodes. The micro-structural and electrochemical corrosion study of base metal (BM), weld zone (WZ) and heat affected zone (HAZ) are carried out to understand the influence of the corrosion product layer generated on the high strength low-alloy steels welded by underwater wet welding with stainless steel electrodes, methods used including, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and scanning electron microscope (SEM). The results indicate that the WZ acts as a cathode and there is no corrosion product on it throughout the immersion period in seawater. The HAZ and BM acts as anodes. The corrosion rates of the HAZ and BM change with the immersion time increasing. In the initial immersion period, the HAZ has the highest corrosion rate because it has a coarse tempered martensite structure and the BM exhibites a microstructure with very fine grains of ferrite and pearlite. After a period of immersion, the BM has the highest corrosion rate. The reason is that the corrosion product layer on the HAZ is dense and has a better protective property while that on the BM is loose and can not inhibit the diffusion of oxygen.

  18. Comparison of spring characteristics of titanium-molybdenum alloy and stainless steel

    PubMed Central

    Salehi, Anahita; Asatourian, Armen

    2017-01-01

    Background Titanium-molybdenum alloy (TMA) and stainless steel (SS) wires are commonly used in orthodontics as arch-wires for tooth movement. However, plastic deformation phenomenon in these arch-wires seems to be a major concern among orthodontists. This study aimed to compare the mechanical properties of TMA and SS wires with different dimensions. Material and Methods Seventy-two wire samples (36 TMA and 36 SS) of three different sizes (19×25, 17×25 and 16×22) were analyzed in vitro, with 12 samples in each group. Various mechanical properties of the wires, including spring-back, bending moment and stiffness were determined using a universal testing machine. Student’s t-test showed statistically significant differences in the mean values of all the groups. In addition, metallographic comparison of SS and TMA wires was conducted under an optical microscope. Results The degree of stiffness of 16×22-sized SS and TMA springs was found to be 12±2 and 5±0.4, respectively, while the bending moment was estimated to be 1927±352 (gm-mm) and 932±16 (gm-mm), respectively; the spring-back index was determined to be 0.61±0.2 and 0.4±.09, respectively (p<0.001). There were no statistically significant differences in spring-back index in larger dimensions of the wires. Conclusions Systematic analysis indicated that springs made of TMA were superior compared to those made of SS. Although both from economic and functionality viewpoints the use of TMA is suggested, further clinical investigations are recommended. Key words:Bending moment, optical microscope, spring-back, stainless steel, stiffness, titanium‒molybdenum alloy. PMID:28149469

  19. Influence of annealing conditions on microstructure and phase occurrence in high-alloy CrMnN steels

    SciTech Connect

    Bakajova, Jana; Domankova, Maria; Cicka, Roman; Eglsaeer, Sabine; Janovec, Jozef

    2010-10-15

    The influence of annealing at 750, 800, 850, 900 and 950 deg. C for 4 h on the microstructure and the phase occurrence in two high-alloy CrMnN austenitic stainless steels was investigated using light microscopy, transmission electron microscopy, and thermodynamic calculations. Austenite, {sigma}, and Cr{sub 2}N were identified in both steels experimentally. The experimental results were found to be in good agreement with the thermodynamic predictions. In one of the steels, M{sub 23}C{sub 6} as a non-equilibrium probably residual phase was found. Cr{sub 2}N appeared in the steels either in the form of discrete particles or as a part of cells consisting of alternate lamellae of Cr{sub 2}N and austenite.

  20. Structure and Properties of High-Temperature Multilayer Hybrid Material Based on Vanadium Alloy and Stainless Steel

    NASA Astrophysics Data System (ADS)

    Nechaykina, Tatyana A.; Nikulin, Sergey A.; Rozhnov, Andrey B.; Khatkevich, Vladimir M.; Rogachev, Stanislav O.

    2017-01-01

    The present work is devoted to the development of new structural composite material having the unique complex of properties for operating in ultrahard conditions that combine high temperatures, radiation, and aggressive environments. A new three-layer composite tube material based on vanadium alloy (V-4Ti-4Cr) protected by stainless steel (Fe-0.2C-13Cr) has been obtained by co-extrusion. Mechanism and kinetics of formation as well as structure, composition, and mechanical properties of "transition" area between vanadium alloy and stainless steel have been studied. The transition area (13- to 22-µm thick) of the diffusion interaction between vanadium alloy and steel was formed after co-extrusion. The microstructure in the transition area was rather complicated comprising different grain sizes in components, but having no defects or brittle phases. Tensile strength of the composite was an average 493 ± 22 MPa, and the elongation was 26 ± 3 pct. Annealing at 1073 K (800 °C) increased the thickness of transition area up to 1.2 times, homogenized microstructure, and slightly changed mechanical properties. Annealing at 1273 K (1000 °C) further increased the thickness of transition area and also lead to intensive grain growth in steel and sometimes to separation between composite components during tensile tests. Annealing at 1073 K (800 °C) is proposed as appropriate heat treatment after co-extrusion of composite providing balance between diffusion interaction thickness and microstructure and monolithic-like behavior of composite during tensile tests.

  1. Structure and Properties of High-Temperature Multilayer Hybrid Material Based on Vanadium Alloy and Stainless Steel

    NASA Astrophysics Data System (ADS)

    Nechaykina, Tatyana A.; Nikulin, Sergey A.; Rozhnov, Andrey B.; Khatkevich, Vladimir M.; Rogachev, Stanislav O.

    2017-03-01

    The present work is devoted to the development of new structural composite material having the unique complex of properties for operating in ultrahard conditions that combine high temperatures, radiation, and aggressive environments. A new three-layer composite tube material based on vanadium alloy (V-4Ti-4Cr) protected by stainless steel (Fe-0.2C-13Cr) has been obtained by co-extrusion. Mechanism and kinetics of formation as well as structure, composition, and mechanical properties of "transition" area between vanadium alloy and stainless steel have been studied. The transition area (13- to 22- µm thick) of the diffusion interaction between vanadium alloy and steel was formed after co-extrusion. The microstructure in the transition area was rather complicated comprising different grain sizes in components, but having no defects or brittle phases. Tensile strength of the composite was an average 493 ± 22 MPa, and the elongation was 26 ± 3 pct. Annealing at 1073 K (800 °C) increased the thickness of transition area up to 1.2 times, homogenized microstructure, and slightly changed mechanical properties. Annealing at 1273 K (1000 °C) further increased the thickness of transition area and also lead to intensive grain growth in steel and sometimes to separation between composite components during tensile tests. Annealing at 1073 K (800 °C) is proposed as appropriate heat treatment after co-extrusion of composite providing balance between diffusion interaction thickness and microstructure and monolithic-like behavior of composite during tensile tests.

  2. PERFORMANCE IMPROVEMENT OF CREEP-RESISTANT FERRITIC STEEL WELDMENTS THROUGH THERMO-MECHANICAL TREATMENT AND ALLOY DESIGN

    SciTech Connect

    Yamamoto, Yukinori; Babu, Prof. Sudarsanam Suresh; Shassere, Benjamin; Yu, Xinghua

    2016-01-01

    Two different approaches have been proposed for improvement of cross-weld creep properties of the high temperature ferrous structural materials for fossil-fired energy applications. The traditional creep strength-enhanced ferritic (CSEF) steel weldments suffer from Type IV failures which occur at the fine-grained heat affected zone (FGHAZ). In order to minimize the premature failure at FGHAZ in the existing CSEF steels, such as modified 9Cr-1Mo ferritic-martensitic steels (Grade 91), a thermo-mechanical treatment consisting of aus-forging/rolling and subsequent aus-aging is proposed which promotes the formation of stable MX carbonitrides prior to martensitic transformation. Such MX remains undissolved during welding process, even in FGHAZ, which successfully improves the cross-weld creep properties. Another approach is to develop a new fully ferrtic, creep-resistant FeCrAl alloy which is essentially free from Type IV failure issues. Fe-30Cr-3Al base alloys with minor alloying additions were developed which achieved a combination of good oxidation/corrosion resistance and improved tensile and creep performance comparable or superior to Grade 92 steel.

  3. Modification of Low-Alloy Steel Surface by Plasma Electrolytic Nitriding

    NASA Astrophysics Data System (ADS)

    Kusmanov, S. A.; Smirnov, A. A.; Silkin, S. A.; Belkin, P. N.

    2016-07-01

    The structure of the low-alloy steel after plasma electrolytic nitriding (PEN) in electrolyte containing ammonium nitrate was investigated. The cross-sectional microstructure, composition, and phase constituents of modified layer under different processing conditions were characterized. It is shown that anode PEN provides the saturation of steel with nitrogen and formation of α-Fe2O3, FeO, and Fe3O4 oxides, Fe2-3N nitride, and martensite. The aqueous solution that contained 15 wt.% NH4Cl and 5 wt.% NH4NO3 allows one to obtain the hardened layer with a thickness of 80 μm and a microhardness up to 740 HV during 5 min at 850 °C. Surface roughness decreases from 1.5 to 0.8 μm after 5-min PEN at 650 °C. The proposed electrolyte and processing mode (750 °C, 10 min) enable to obtain the decrease in the weight loss after lubricate wear testing by a factor of 2.7. The base-nitrate electrolyte conditioned a decrease in the corrosion current density by a factor of 9 due to passivating effect of the oxide and nitride of iron.

  4. Development of rapidly quenched brazing foils to join tungsten alloys with ferritic steel

    NASA Astrophysics Data System (ADS)

    Kalin, B. A.; Fedotov, V. T.; Sevrjukov, O. N.; Moeslang, A.; Rohde, M.

    2004-08-01

    Results on rapidly solidified filler metals for tungsten brazing are presented. A rapidly quenched foil-type filler metal based on Ni bal-15Cr-4Mo-4Fe-(0.5-1.0)V-7.5Si-1.5B was developed to braze tungsten to ferritic/martensitic Crl3Mo2NbVB steel (FS) for helium gas cooled divertors and plasma facing components. Polycrystalline W-2CeO 2 and monocrystalline pure tungsten were brazed to the steel under vacuum at 1150 °C, using a 0.5 mm thick foil spacer made of a 50Fe-50Ni alloy. As a result of thermocycling tests (100 cycles between 700 °C/20 min and air-water cooling/3-5 min) on brazed joints, tungsten powder metallurgically processed W-2CeO 2 failed due to residual stresses, whereas the brazed joint with zone-melted monocrystalline tungsten withstood the thermocycling tests.

  5. Characterization and Cytotoxic Assessment of Ballistic Aerosol Particulates for Tungsten Alloy Penetrators into Steel Target Plates

    PubMed Central

    Machado, Brenda I.; Murr, Lawrence E.; Suro, Raquel M.; Gaytan, Sara M.; Ramirez, Diana A.; Garza, Kristine M.; Schuster, Brian E.

    2010-01-01

    The nature and constituents of ballistic aerosol created by kinetic energy penetrator rods of tungsten heavy alloys (W-Fe-Ni and W-Fe-Co) perforating steel target plates was characterized by scanning and transmission electron microscopy. These aerosol regimes, which can occur in closed, armored military vehicle penetration, are of concern for potential health effects, especially as a consequence of being inhaled. In a controlled volume containing 10 equispaced steel target plates, particulates were systematically collected onto special filters. Filter collections were examined by scanning and transmission electron microscopy (SEM and TEM) which included energy-dispersive (X-ray) spectrometry (EDS). Dark-field TEM identified a significant nanoparticle concentration while EDS in the SEM identified the propensity of mass fraction particulates to consist of Fe and FeO, representing target erosion and formation of an accumulating debris field. Direct exposure of human epithelial cells (A549), a model for lung tissue, to particulates (especially nanoparticulates) collected on individual filters demonstrated induction of rapid and global cell death to the extent that production of inflammatory cytokines was entirely inhibited. These observations along with comparisons of a wide range of other nanoparticulate species exhibiting cell death in A549 culture may suggest severe human toxicity potential for inhaled ballistic aerosol, but the complexity of the aerosol (particulate) mix has not yet allowed any particular chemical composition to be identified. PMID:20948926

  6. Characterization and cytotoxic assessment of ballistic aerosol particulates for tungsten alloy penetrators into steel target plates.

    PubMed

    Machado, Brenda I; Murr, Lawrence E; Suro, Raquel M; Gaytan, Sara M; Ramirez, Diana A; Garza, Kristine M; Schuster, Brian E

    2010-09-01

    The nature and constituents of ballistic aerosol created by kinetic energy penetrator rods of tungsten heavy alloys (W-Fe-Ni and W-Fe-Co) perforating steel target plates was characterized by scanning and transmission electron microscopy. These aerosol regimes, which can occur in closed, armored military vehicle penetration, are of concern for potential health effects, especially as a consequence of being inhaled. In a controlled volume containing 10 equispaced steel target plates, particulates were systematically collected onto special filters. Filter collections were examined by scanning and transmission electron microscopy (SEM and TEM) which included energy-dispersive (X-ray) spectrometry (EDS). Dark-field TEM identified a significant nanoparticle concentration while EDS in the SEM identified the propensity of mass fraction particulates to consist of Fe and FeO, representing target erosion and formation of an accumulating debris field. Direct exposure of human epithelial cells (A549), a model for lung tissue, to particulates (especially nanoparticulates) collected on individual filters demonstrated induction of rapid and global cell death to the extent that production of inflammatory cytokines was entirely inhibited. These observations along with comparisons of a wide range of other nanoparticulate species exhibiting cell death in A549 culture may suggest severe human toxicity potential for inhaled ballistic aerosol, but the complexity of the aerosol (particulate) mix has not yet allowed any particular chemical composition to be identified.

  7. Experimental Study on Vacuum Carburizing Process for Low-Carbon Alloy Steel

    NASA Astrophysics Data System (ADS)

    Wei, Shaopeng; Wang, Gang; Zhao, Xianhui; Zhang, Xiaopeng; Rong, Yiming

    2013-10-01

    As a low-carbon alloy steel, 20Cr2Ni4A steel has an excellent mechanical properties. It has been used for producing heavy-duty gears, which require good wear and fatigue resistance. The vacuum carburizing process can improve the quality of gears and extend the service life. In this article, a complete heat-treatment process for 20Cr2Ni4A, with carburizing, tempering, quenching and cryogenic steps involved, was proposed. A numerical method was employed to design the carburizing step. The carburized samples were characterized by analysis of carbon profile, surface-retained austenite content, microstructure, and hardness profile. A good microstructure was obtained with acicular-tempered martensite, less-retained austenite, fine granular-dispersed carbides, and was oxide free. The final surface hardness was 64.2HRC, and the case depth was 0.86 mm, which meet the requirements of products. The relationships among process, performance, and microstructure were investigated to understand the inner connection.

  8. Dynamic Deformation and Fragmentation Response of Maraging Steel Linear Cellular Alloy

    NASA Astrophysics Data System (ADS)

    Jakus, Adam; Fredenburg, D. A.; McCoy, T.; Thadhani, N. N.; Cochran, J.

    2011-06-01

    The dynamic deformation and fragmentation response of 25% dense 9-cell linear cellular alloy (LCA) made of unaged 250 maraging steel, fabricated using a direct reduction and extrusion technique, is investigated. Explicit finite element simulations were implemented using AUTODYN. The maraging steel properties were defined using a Johnson-Cook strength model with previously validated parameters. Rod-on-anvil impact tests were performed using the 7.6 mm helium gas gun and the transient deformation and fragmentation response was recorded with high-speed imaging. For purpose of comparison, the response of 25% dense hollow cylinders of same density as the 9-cell LCA was also studied. Analysis of observed states of specimens and finite element simulations reveal that in the case of the 9-cell LCA, dissipation of stress and strain occurs along the interior cell wells resulting in significant and ubiquitous buckling prior to confined fragmentation. In comparison, the simple hollow cylinder undergoes significant radial lipping, eventually producing larger sized, external fragments. DTRA Grant No. HDTRA1-07-1-0018 and NDSEG Fellowship Program.

  9. Residual stresses in a stainless steel - titanium alloy joint made with the explosive technique

    NASA Astrophysics Data System (ADS)

    Taran, Yu V.; Balagurov, A. M.; Sabirov, B. M.; Evans, A.; Davydov, V.; Venter, A. M.

    2012-02-01

    Joining of pipes from stainless steel (SS) and titanium (Ti) alloy still experience serious technical problems. Recently, reliable and hermetic joining of SS and Ti pipes has been achieved with the explosive bonding technique in the Russian Federal Nuclear Center. Such adapters are earmarked for use at the future International Linear Collider. The manufactured SS-Ti adapters have excellent mechanical behavior at room and liquid nitrogen temperatures, during high-pressure tests and thermal cycling. We here report the first neutron diffraction investigation of the residual stresses in a SS-Ti adapter on the POLDI instrument at the SINQ spallation source. The strain scanning across the adapter walls into the SS-SS and SS-Ti pipes sections encompassed measurement of the axial, radial and hoop strain components, which were transformed into residual stresses. The full stress information was successfully determined for the three steel pipes involved in the joint. The residual stresses do not exceed 300 MPa in magnitude. All stress components have tensile values close to the adapter internal surface, whilst they are compressive close to the outer surface. The strong incoherent and weak coherent neutron scattering cross-sections of Ti did not allow for the reliable determination of stresses inside the titanic pipe.

  10. Creep Void Detection for Low Alloy Steel Using AC Magnetic Method

    SciTech Connect

    Shiwa, M.; Cheng, W.; Kume, R.

    2004-02-26

    Nondestructive detection of creep void was developed for low alloy steel by using AC magnetic method. Two types of 2.25Cr-1Mo steel specimens, base metal (BM) and simulated heat affected zone (HAZ) under aging and creep damage, were prepared for the tests. A differential type probe was used to detect AC magnetic signals. The exciting and detecting coils were coaxially arranged with a ferrite core. Signals were recorded using a 2-channel waveform recorder. The equivalent hysteresis loss (HL) was analyzed. It was observed that the HL of BM and HAZ changed in opposite direction, that is, HL of BM increased and HL of HAZ decreased with aging time. On the other hand, the HLs of both BM and HAZ decreased with creep time. The HL of creep samples was affected by both aging and stress-induced damage. In order to evaluate creep damage, stress-induced damage (SID) parameter was proposed to remove aging factor of materials from HL. Creep void were observed by scanning electron microscope (SEM) for all creep damage samples of SID value under 0.8.

  11. Microstructure, Precipitation, and Mechanical Properties of V-N-Alloyed Steel After Different Cooling Processes

    NASA Astrophysics Data System (ADS)

    Zhang, Jing; Wang, Fu-Ming; Yang, Zhan-Bing; Li, Chang-Rong

    2016-12-01

    Three cooling processes (direct air cooling, water cooling to 1023 K and 873 K (750 °C and 600 °C) followed by air cooling) after hot rolling are designed to develop V-N-alloyed 600 MPa grade high-strength steel for architectural construction. Microstructural characteristics, precipitation behavior, and mechanical properties were investigated. Experimental results indicate that all microstructures are composed of polygonal ferrite and pearlite. Compared to the microstructure obtained from traditional direct air cooling, the grain size of ferrite is refined from 6.5 to 4.6 μm and the interlamellar spacing of pearlite decreases from 136 to 45 nm, respectively, by the application of accelerated cooling and lower finish cooling temperature. The number fraction of high misorientation angle boundaries increases from 44 to 51 pct. Moreover, the sheet spacing of interphase precipitates decreases from (23 to 26 nm) to (14 to 17 nm) and the size of V(C,N) particles reduces from (5 to 8 nm) to (2 to 5 nm). Furthermore, the optimal mechanical properties are obtained in the steel water cooled to 873 K (600 °C), of which the yield strength, tensile strength, total elongation, uniform elongation, and impact energy at room temperature are 753 MPa, 922 MPa, 22 pct, 11 pct, and 36 J, respectively. Besides, the high yield strength is primarily attributed to the refined grains and precipitation hardening from interphase and random precipitation of nano-scale V(C,N) particles.

  12. Special Features of Structure Formation in Pipes from Medium-Carbon Low-Alloy Steel 32G2F Under Heat Treatment

    NASA Astrophysics Data System (ADS)

    Stepanov, A. I.; Belikov, S. V.; Musikhin, S. A.; Burmasov, S. P.; Popov, A. A.

    2017-03-01

    Special features of formation of structure and properties of seamless pipes from medium-carbon low-alloy steel for oil and gas applications are considered and associated with chemical inhomogeneity of the metal of the pipes.

  13. Influence of alloy content and a cerium surface treatment on the oxidation behavior of Fe-Cr ferritic stainless steels

    SciTech Connect

    Alman, D.E.; Jablonski, P.D.

    2006-01-01

    The cost of solid oxide fuel cells (SOFC) can be significantly reduced by using interconnects made from ferritic stainless steels. In fact, several alloys have been developed specifically for this application (Crofer 22APU and Hitachi ZMG323). However, these steels lack environmental stability in SOFC environments, and as a result, degrade the performance of the SOFC. A steel interconnect can contribute to performance degradation through: (i) Cr poisoning of electrochemically active sites within the cathode; (ii) formation of non-conductive oxides, such as SiO2 or Al2O3 from residual or minor alloying elements, at the base metal-oxide scale interface; and/or (iii) excessive oxide scale growth, which may also retard electrical conductivity. Consequently, there has been considerable attention on developing coatings to protect steel interconnects in SOFC environments and controlling trace elements during alloy production. Recently, we have reported on the development of a Cerium surface treatment that improves the oxidation behavior of a variety alloys, including Crofer 22APU [1-5]. Initial results indicated that the treatment may improve the performance of Crofer 22APU for SOFC application by: (i) retarding scale growth resulting in a thinner oxide scale; and (ii) suppressing the formation of a deleterious continuous SiO2 layer that can form at the metal-oxide scale interface in materials with high residual Si content [5]. Crofer 22 APU contains Fe-22Cr-0.5Mn-0.1Ti (weight percent). Depending on current market prices and the purity of raw materials utilized for ingot production, Cr can contribute upwards of 90 percent of the raw materials cost. The present research was undertaken to determine the influence of Cr content and minor element additions, especially Ti, on the effectiveness of the Ce surface treatment. Particular emphasis is placed on the behavior of low Cr alloys.

  14. Microstructure and Properties of Lap Joint Between Aluminum Alloy and Galvanized Steel by CMT

    NASA Astrophysics Data System (ADS)

    Niu, Song; Chen, Su; Dong, Honggang; Zhao, Dongsheng; Zhang, Xiaosheng; Guo, Xin; Wang, Guoqiang

    2016-05-01

    Lap joining of 1-mm-thick Novelist AC 170 PX aluminum alloy to 1.2-mm-thick ST06 Z galvanized steel sheets for automotive applications was conducted by cold metal transfer advanced welding process with ER4043 and ER4047 filler wires. Under the optimized welding parameters with ER4043 filler wire, the tensile shear strength of joint was 189 MPa, reaching 89% of the aluminum alloy base metal. Microstructure and elemental distribution were characterized by optical metalloscope and electron probe microanalysis. The lap joints with ER4043 filler wire had smaller wetting angle and longer bonded line length with better wettability than with ER4047 filler wire during welding with same parameters. The needle-like Al-Fe-Si intermetallic compounds (IMCs) were spalled into the weld and brought negative effect to the tensile strength of joints. With increasing welding current, the needle-like IMCs grew longer and spread further into the weld, which would deteriorate the tensile shear strength.

  15. Tempering kinetics of alloy steels as a function of quench rate and Ms temperature

    NASA Astrophysics Data System (ADS)

    Hennessy, Daniel G.; Sharma, Vijay; Ansell, G. S.

    1983-06-01

    The effect of quench rate on the as-quenched hardness and carbide or carbon segregate particle size was studied for two alloy steels with Ms temperatures of 310 °C and 300 °C. The quench rate was varied from 681 to 93,000 °C per second. The hardness was studied using the Vickers hardness technique and the particle size was measured using the high-resolution, small-angle X-ray scattering technique. The as-quenched hardness and particle size were both found to decrease as the quench rate increased. Analysis of the data ruled out autotempering of the martensite as a likely basis for the observed quench rate effects. The effects of aging at room temperature (20 °C) on the hardness and particle size for these alloys were also studied. The hardness and particle size were both found to increase as the aging time increased. After 24 hours of aging, the effect of quench rate disappeared in that the hardness and particle size attained were each essentially independent of quench rate.

  16. Compatibility of U-Pu-Zr alloy fuel with stainless steel cladding

    SciTech Connect

    Leibowitz, L.; Hins, A. G.; Strain, R. V.; Tsai, H.; Hofman, G. L.

    1989-07-01

    An important issue in the development of the Integral Fast Reactor is the chemical interaction between fuel and cladding. With a U--Pu--Zr ternary alloy fuel clad in stainless steel, the existence of low-melting eutectics in the U--Fe and Pu--Fe systems must be taken into account. There is at least the possibility that cladding integrity could be compromised by formation of liquid phases during irradiation. Data from a variety of sources have been brought to bear on this issue, and our current state of understanding is summarized in this report. The phase behavior of the relevant systems has been studied to provide a framework for understanding fuel/cladding interactions. Several experimental methods have been used. Differential thermal analysis experiments were performed, and the results compared with those of the phase studies. In addition, experiments were performed in which unirradiated fuel was heated in contact with cladding alloys. The results of these tests were strongly dependent on the state of the contacting surfaces. Other tests were performed in which sections of irradiated fuel with cladding were subjected to carefully controlled heating cycles. In general, there were no inconsistencies in these experimental and analytical studies although the data are still fragmentary. Differences that were observed may be reflections of kinetic factors. 9 refs., 12 figs., 6 tabs.

  17. A mechanical property and stress corrosion evaluation of Custom 455 stainless steel alloy

    NASA Technical Reports Server (NTRS)

    Montano, J. W.

    1972-01-01

    The mechanical and stress corrosion properties are presented of vacuum melted Custom 455 stainless steel alloy bar (1.0-inch diameter) and sheet (0.083-inch thick) material aged at 950 F, 1000 F, and 1050 F. Low temperature mechanical properties were determined at temperatures of 80 F, 0 F, -100 F, and -200 F. For all three aging treatments, the ultimate tensile and 0.2 percent offset yield strengths increased with decreasing test temperatures while the elongation held fairly constant down to -100 F and decreased at -200 F. Reduction in Area decreased moderately with decreasing temperature for the longitudinal round (0.250-inch diameter) specimens. Notched tensile strength and charpy V-notched impact strength decreased with decreasing test temperature. For all three aging treatments, no failures were observed in the unstressed specimens or the specimens stressed to 50, 75, and 100 percent of their yield strengths for 180 days of alternate immersion testing in a 3.5 percent NaCl solution. As indicated by the results of tensile tests performed after alternate immersion testing, the mechanical properties of Custom 455 alloy were not affected by stress or exposure under the conditions of the evaluation.

  18. Electrodeposition of Mn-Co Alloys on Stainless Steels for SOFC Interconnect Application

    SciTech Connect

    Wu, J.; Jiang, Y.; Johnson, C.; Gong, M.; Liu, X.

    2007-09-01

    Chromium-containing ferritic stainless steels are the most popular materials for solid oxide fuel cell (SOFC) interconnect applications because of its oxidation resistance and easy fabrication process. However, excessive scale growth and chromium evaporation will degrade the cell performance. Highly conductive coatings that resist oxide scale growth and chromium evaporation may prevent both of these problems. Mn1.5Co1.5O4 spinel is one of the most promising coatings for interconnect application because of its high conducitivy, good chromium retention capability, as well as good CTE match. Electroplating of alloys or thin film multilayers followed by controlled oxidation to the desired spinel phase offers an additional deposition option. In the present study binary Mn/Co alloys was fabricated by electrodeposition, and polarization curves were used to characterize the cathodic reactions on substrate surface. By controlling the current density precisely, coatings with Mn/Co around 1:1 has been successfully deposited in Mn/Co =10 solutions, SEM and EDX was used to characterize the surface morphology and composition.

  19. Macrophage responses to 316L stainless steel and cobalt chromium alloys with different surface topographies.

    PubMed

    Anderson, Jordan A; Lamichhane, Sujan; Mani, Gopinath

    2016-11-01

    The surface topography of a biomaterial plays a vital role in determining macrophage interactions and influencing immune response. In this study, we investigated the effect of smooth and microrough topographies of commonly used metallic biomaterials such as 316 L stainless steel (SS) and cobalt-chromium (CoCr) alloys on macrophage interactions. The macrophage adhesion was greater on CoCr compared to SS, irrespective of their topographies. The macrophage activation and the secretion of most pro-inflammatory cytokines (TNF-α, IL-6, and IP-10) were greater on microrough surfaces than on smooth surfaces by day-1. However, by day-2, the macrophage activation on smooth surfaces was also significantly increased up to the same level as observed on the microrough surfaces, with more amount of cytokines secreted. The secretion of anti-inflammatory cytokine (IL-10) was significantly increased from day-1 to day-2 on all the alloy surfaces with the effect most prominently observed on microrough surfaces. The production of nitric oxide by the macrophages did not show any major substrate-dependent effect. The foreign body giant cells formed by macrophages were least observed on the microrough surfaces of CoCr. Thus, this study demonstrated that the nature of material (SS or CoCr) and their surface topographies (smooth or microrough) strongly influence the macrophage responses. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2658-2672, 2016.

  20. Effects of H2 Atmospheres on Sintering of Low Alloy Steels Containing Oxygen-Sensitive Masteralloys

    NASA Astrophysics Data System (ADS)

    de Oro Calderon, Raquel; Jaliliziyaeian, Maryam; Gierl-Mayer, Christian; Danninger, Herbert

    2017-02-01

    Processing of novel sintered steels with compositions including oxygen-sensitive elements requires deep understanding of the chemistry of sintering. The use of H2 atmospheres alleviates the oxygen transference from the base powder to the oxygen-sensitive particles. However, in H2, methane formation at 700-1200°C causes dramatic homogeneous decarburization of the part that affects both mechanical behavior and dimensional stability. The intensity and the critical temperatures of this effect depend strongly on the alloying elements, being significantly enhanced in presence of Si. When combining the alloying elements as Fe-Mn-Si masteralloys, methane formation is enhanced around 760°C due to the high Mn content (40 wt.%) in the masteralloys. Nevertheless, the benefits of H2 towards oxide reduction can still be advantageously used if diluting it in the form of N2-H2 atmospheres, or if limiting the use of H2 to temperatures below 500°C. Thus, decarburization due to methane formation can be successfully controlled.

  1. Effect of fine scale microstructure and inclusions on the toughness of ultra high strength low alloy medium carbon steels

    NASA Astrophysics Data System (ADS)

    Choudhary, Pranay

    When fracture is due to micro-void coalescence the toughness of ultra high strength steels is determined by the nature of the inclusions in the steel and by the fine-scale microstructure of the steel. It has been previously shown for the steels HY180 (0.1 wt.% carbon) and AF1410 (0.16 wt.% carbon) that one can improve toughness by increasing inclusion spacing through the use of rare-earths and similarly increase toughness by having inclusion types that are resistant to void nucleation though the use of titanium additions. The purpose of this work has been to determine the extent to which rare-earth additions and titanium additions can be used to control inclusion characteristics and improve the toughness of ultra high strength low alloy steels such as 4340 (0.4 wt.% carbon) and 300M. Because silicon additions on the order of 2 wt.% can be used to increase the strength of 0.4 wt.% carbon low-alloy steels without resorting to increased carbon levels, this work also examined the degree to which silicon content influences the inclusion distributions when rare-earth additions or titanium additions are used to modify inclusion type. Two separate low-alloy systems, 4340 and Base+Ni+Si series alloys were investigated. Extensive mechanical testing was performed by tensile testing, plane strain fracture toughness tests and Charpy impact toughness tests. True stress-true strain curves were obtained by applying the method of Bridgman. The inclusion analysis of the micrographs obtained using SEM was used to obtain the average inclusion radius, inclusion volume fraction and inclusion spacing. Void nucleation curves were obtained to characterize the strain at which inclusions first nucleate voids. Subsequently the critical interfacial stress at which these inclusions nucleate voids was also obtained. The retained austenite content was measured using X-Ray diffraction while analysis of thin foils and extraction replicas was performed using Transmission Electron Microscopy (TEM

  2. Fatigue crack initiation in carbon and low-alloy steels in light water reactor environments : mechanism and prediction.

    SciTech Connect

    Chopra, O. K.; Shack, W. J.

    1998-01-27

    Section 111 of the ASME Boiler and Pressure Vessel Code specifies fatigue design curves for structural materials. The effects of reactor coolant environments are not explicitly addressed by the Code design curves. Recent test data illustrate potentially significant effects of light water reactor (LWR) coolant environments on the fatigue resistance of carbon and low-alloy steels. Under certain loading and environmental conditions, fatigue lives of test specimens may be shorter than those in air by a factor of {approx}70. The crack initiation and crack growth characteristics of carbon and low-alloy steels in LWR environments are presented. Decreases in fatigue life of these steels in high-dissolved-oxygen water are caused primarily by the effect of environment on growth of short cracks < 100 {micro}m in depth. The material and loading parameters that influence fatigue life in LWR environments are defined. Fatigue life is decreased significantly when five conditions are satisfied simultaneously, viz., applied strain range, service temperature, dissolved oxygen in water, and S content in steel are above a threshold level, and loading strain rate is below a threshold value. Statistical models have been developed for estimating the fatigue life of these steels in LWR environments. The significance of the effect of environment on the current Code design curve is evaluated.

  3. Modeling of porosity formation and feeding flow during casting of steel and aluminum alloys

    NASA Astrophysics Data System (ADS)

    Lin, Zhiping

    Porosity is one of the most important defects in metal casting. To quantitatively predict the porosity formation during casting two numerical models are developed for steel and aluminum alloys respectively. For steel, a multi-phase model is developed that predicts melt pressure, feeding flow, porosity (both microscopic and macroscopic), and riser pipe formation during casting. The phases included in the model are solid, liquid, porosity, and air. An energy equation is solved to determine solid fraction. A multi-phase momentum equation, which is valid everywhere in the solution domain, is derived. A pressure equation is then derived from this momentum equation and a mixture continuity equation developed that accounts for all phases. The partial pressure of a gas species dissolved in the melt is determined using the species concentration, which is found by solving a species conservation equation that accounts for convection. Porosity forms once the gas pressure exceeds the sum of the melt pressure and the capillary pressure. The amount of porosity that forms is determined from the mixture continuity equation. The riser pipe is determined from an air continuity equation. A pore size model, which considers the effects of the solidifying steel microstructure on pore size, is incorporated into the multi-phase model. The multi-phase model is applied to one-dimensional, two-dimensional, and three-dimensional simulations. The results clearly illustrate the basic physical phenomena involved and predict microporosity and macroporosity distributions, as well as a riser pipe. For aluminum alloys a gas microsegregation model is developed to quantitatively predict porosity, coupled with the calculations of the pressure field, feeding flow, and distribution of dissolved gas species throughout the casting. The effects of dendritic and eutectic microstructure on the pore shape and size are considered in a pore size model. The model is applied to one-dimensional simulations of A319

  4. Effects of alloying elements and heat treatments on mechanical properties of Korean reduced-activation ferritic-martensitic steel

    NASA Astrophysics Data System (ADS)

    Chun, Y. B.; Kang, S. H.; Noh, S.; Kim, T. K.; Lee, D. W.; Cho, S.; Jeong, Y. H.

    2014-12-01

    As part of an alloy development program for Korean reduced-activation ferritic-martensitic (RAFM) steel, a total of 37 program alloys were designed and their mechanical properties were evaluated with special attention being paid to the effects of alloying elements and heat treatments. A reduction of the normalizing temperature from 1050 °C to 980 °C was found to have a positive effect on the impact resistance, resulting in a decrease in ductile-brittle transition-temperature (DBTT) of the program alloys by an average of 30 °C. The yield strength and creep rupture time are affected strongly by the tempering time at 760 °C but at the expense of ductility. Regarding the effects of the alloying elements, the addition of trace amounts of Zr enhances both the creep and impact resistance: the lowest DBTT was observed for the alloys containing 0.005 wt.% Zr, whereas the addition of 0.01 wt.% Zr extends the creep rupture-time under an accelerated condition. The enhanced impact resistance owing to the normalizing at lower temperature is attributed to a more refined grain structure, which provides more barriers to the propagation of cleavage cracks. Solution softening by Zr addition is suggested as a possible mechanism for enhanced resistance to both impact and creep of the program alloys.

  5. Fast Salt Bath Heat Treatment for a Bainitic/Martensitic Low-Carbon Low-Alloyed Steel

    NASA Astrophysics Data System (ADS)

    Urbanec, Julia; Saastamoinen, Ari; Kivivuori, Seppo; Louhenkilpi, Seppo

    2015-11-01

    The mechanical properties of a low-alloyed steel with 0.06 wt pct C were investigated after a series of heat treatment processes using salt bath followed by quenching into water in order to obtain bainitic/martensitic steel. Salt bath holding time varied from 30 to 330 seconds. Hardness, tensile properties and toughness have been examined. The results show the obtained microstructure significantly enhances the impact strength (up to 187 J) and toughness (up to 71.4 pct critical reduction) with good hardness (239 ± 4 HV) and tensile strength (720 to 800 MPa) compared to direct quenching heat treatment without salt bath holding.

  6. Effect of material flow on joint strength in activation spot joining of Al alloy and steel sheets

    NASA Astrophysics Data System (ADS)

    Watanabe, Goro; Yogo, Yasuhiro; Takao, Hisaaki

    2014-08-01

    A new joining method for dissimilar metal sheets was developed where a rotated consumable rod of Al alloy is pressed onto an Al alloy sheet at the part overlapped with a mild steel sheet. The metal flow in the joining region is increased by the through-hole in the Al sheet and consumable Al rod. The rod creates the joint interface and pads out of the thinly joined parts through pressing. This produces a higher joint strength than that of conventional friction stir spot welding. Measurements of the joint interface showed the presence of a 5-10 nm thick amorphous layer consisting of Al and Mg oxides.

  7. Comparative studies on shielding properties of some steel alloys using Geant4, MCNP, WinXCOM and experimental results

    NASA Astrophysics Data System (ADS)

    Singh, Vishwanath P.; Medhat, M. E.; Shirmardi, S. P.

    2015-01-01

    The mass attenuation coefficients, μ/ρ and effective atomic numbers, Zeff of some carbon steel and stainless steel alloys have been calculated by using Geant4, MCNP simulation codes for different gamma ray energies, 279.1 keV, 661.6 keV, 662 keV, 1115.5 keV, 1173 keV and 1332 keV. The simulation results of Zeff using Geant4 and MCNP codes have been compared with possible available experimental results and theoretical WinXcom, and good agreement has been observed. The simulated μ/ρ and Zeff values using Geant4 and MCNP code signifies that both the simulation process can be followed to determine the gamma ray interaction properties of the alloys for energies wherever analogous experimental results may not be available. This kind of studies can be used for various applications such as for radiation dosimetry, medical and radiation shielding.

  8. Effect of Heat Treatment on the Impact Toughness of `High-Chromium Cast Iron - Low Alloy Steel' Bimetal Components

    NASA Astrophysics Data System (ADS)

    Özdemir, Z.

    2017-03-01

    A bimetallic `low-alloy steel - high-chromium cast iron' composite obtained by successive sand casting is studied and shown to have good cohesion on the interface and no casting defects. The hardness and the impact toughness of the bimetal increase simultaneously. The microstructure is more homogeneous after diffusion annealing at 1040°C, rapid cooling, and 3-h tempering at 270°C.

  9. Evaluation of pitting corrosion resistance of high-alloyed stainless steels welds for FGD plants in Korea

    SciTech Connect

    Baek, K.K.; Sung, H.J.; Im, C.S.; Hong, I.P.; Kim, D.K.

    1998-12-31

    For successful application of high-alloyed stainless steels for Flue Gas Desulfurization (FGD) plants, pitting corrosion resistance of arc welds of N-added 6%Mo austenitic stainless steels (UNS N 08367) and super duplex stainless steels (UNS S 32550) made with various filler metals were evaluated using the Green Death solution. For Gas Tungsten Arc (GTA) and Gas Metal Arc (GMA) welds of N 08367, Critical Pitting Temperature (CPT) of base metal was 65--70 C, whereas weld made by ERNiCrMo-3 filler metal yielded CPT of 50 C. Welds made by ERNiCrMo-10 or ERNiCrMo-4 filler metals showed CPT of 60--65 C and 65--70C, respectively. For GTA and GMA welds of S 32550, CPT of welds made by ERNiCrMo-3 was 45--50 C, indicating that the filler metal can provide pitting corrosion resistance matching the S 32550 alloy. Thus, a proper pitting corrosion resistance of weldments of high-alloy stainless steels can be achieved by selecting filler metals having at least +10 higher Pitting Resistance Equivalent Number (PRE{sub N}) value than the base metal regardless of the type of arc welding process. The over-alloyed filler metals would compensate preferential segregation of Cr, MO along the dendrite boundary, which made the dendrite core more susceptible to pitting. Nitrogen addition to the GTA welds of N 08367 made with ERNiCrMo-3 failed to improve pitting corrosion resistance, which was attributed to the precipitation of nitrogen in the weld metal in the form of Nb-nitride.

  10. Low-alloy steels for thick-walled pressure vessels. Summary report, February 1, 1980-January 31, 1982

    SciTech Connect

    Todd, J.A.; Chung, D.W.; Parker, E.R.

    1982-01-01

    This program aimed to modify existing commercial pressure vessel steels to provide strong, tough, creep resistant materials, with low hydrogen attack and temper embrittlement susceptibilities, which can also be field-fabricated into thick-section vessels for coal conversion systems. Emphasis was placed on determining the effects of Mn, Ni and Cr on the creep rupture and hydrogen attack susceptibilities of Cr-Mo steels. Hydrogen attack studies were also carried out on A533B and model alloy systems to investigate the role of alloy carbides in promoting resistance to hydrogen damage. Creep rupture fracture times were determined at 500, 560 and 600/sup 0/C for periods up to 2000 hours. The effects of cooling rate from the austenitizing temperature and tempering response on the microstructure of 3Cr-1Mo-1Mn-1Ni steel were studied. The carbide structures in all the alloy modifications were carefully characterized. Data were collected from preliminary weld bead-on-plate tests of A387 and temper embrittlement studies of A543 with mischmetal addition. The unloading compliance test technique for J/sub Ic/ measurements was completed for A533B specimens but shortage of material prevented testing of A387. The mechanical property, elevated temperature creep and hydrogen attack data suggested that addition of 0.75 Cr + 0.5 Mn + 1Ni was beneficial in reducing susceptibility to hydrogen damage but was detrimental to creep rupture properties. 44 figures, 14 tables.

  11. Effects of stress ratio on the temperature-dependent high-cycle fatigue properties of alloy steels

    NASA Astrophysics Data System (ADS)

    Lü, Zhi-yang; Wan, Ao-shuang; Xiong, Jun-jiang; Li, Kuang; Liu, Jian-zhong

    2016-12-01

    This paper addresses the effects of stress ratio on the temperature-dependent high-cycle fatigue (HCF) properties of alloy steels 2CrMo and 9CrCo, which suffer from substantial vibrational loading at small stress amplitude, high stress ratio, and high frequency in the high-temperature environments in which they function as blade and rotor spindle materials in advanced gas or steam turbine engines. Fatigue tests were performed on alloy steels 2CrMo and 9CrCo subjected to constant-amplitude loading at four stress ratios and at four and three temperatures, respectively, to determine their temperature-dependent HCF properties. The interaction mechanisms between high temperature and stress ratio were deduced and compared with each other on the basis of the results of fractographic analysis. A phenomenological model was developed to evaluate the effects of stress ratio on the temperature-dependent HCF properties of alloy steels 2CrMo and 9CrCo. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

  12. The Influence of Forge Reduction Ratio on the Tensile and Impact Properties of a Low-Alloy ESR (Electroslag Remelting) Steel

    DTIC Science & Technology

    1986-01-01

    phenomenon occurs. The ESR steel investigated was a low sulphur (0.002%) - . AISI 4340 grade in the heat treated condition. Attention is also directed toward...MRL-R-985 THE INFLUENCE OF FORGE REDUCTION RATIO ON THE TENSILE AND IMPACT PROPERTIES OF A LOW-ALLOY ESR STEEL G.M. Weston LEC I . ;T E; ’ :cX NMI 5- i...RESEARCH LABORATORIES REPORT MRL-R-98 5 THE INFLUENCE OF FORGE REDUCTION RATIO ON THE TENSILE AND IMPACT PROPERTIES OF A LOW-ALLOY ESR STEEL G.M. Weston

  13. Corrosion Behavior of Low-Alloy Pipeline Steel Exposed to H2S/CO2-Saturated Saline Solution

    NASA Astrophysics Data System (ADS)

    Liu, Zhenguang; Gao, Xiuhua; Du, Linxiu; Li, Jianping; Li, Ping; Bai, Xiaolei; Misra, R. D. K.

    2017-03-01

    Immersion experiments were carried out to study H2S/CO2 corrosion behavior of low-alloy pipeline steel in terms of microstructure, corrosion kinetics, corrosion phases, microscopic surface morphology, cross-sectional morphology and elemental distribution. The experimental results indicated that the microstructure of designed steel was tempered martensite. The corrosion rate followed exponential behavior. H2S corrosion dominated the corrosion process, and the corrosion products were mackinawite, greigite and troilite. The corrosion products changed from mackinawite/greigite to mackinawite/troilite, and mackinawite dominated the corrosion phases. The corrosion products became more compact with immersion time, which led to decrease in corrosion rate. The chromium and molybdenum content in the corrosion product was higher than that in the steel substrate.

  14. Corrosion Behavior of Low-Alloy Pipeline Steel Exposed to H2S/CO2-Saturated Saline Solution

    NASA Astrophysics Data System (ADS)

    Liu, Zhenguang; Gao, Xiuhua; Du, Linxiu; Li, Jianping; Li, Ping; Bai, Xiaolei; Misra, R. D. K.

    2017-02-01

    Immersion experiments were carried out to study H2S/CO2 corrosion behavior of low-alloy pipeline steel in terms of microstructure, corrosion kinetics, corrosion phases, microscopic surface morphology, cross-sectional morphology and elemental distribution. The experimental results indicated that the microstructure of designed steel was tempered martensite. The corrosion rate followed exponential behavior. H2S corrosion dominated the corrosion process, and the corrosion products were mackinawite, greigite and troilite. The corrosion products changed from mackinawite/greigite to mackinawite/troilite, and mackinawite dominated the corrosion phases. The corrosion products became more compact with immersion time, which led to decrease in corrosion rate. The chromium and molybdenum content in the corrosion product was higher than that in the steel substrate.

  15. Investigations on Laser Beam Welding of Different Dissimilar Joints of Steel and Aluminum Alloys for Automotive Lightweight Construction

    NASA Astrophysics Data System (ADS)

    Seffer, Oliver; Pfeifer, Ronny; Springer, André; Kaierle, Stefan

    Due to the enormous potential of weight saving, and the consequential reduction of pollutant emissions, the use of hybrid components made of steel and aluminum alloys is increasing steadily, especially concerning automotive lightweight construction. However, thermal joining of steel and aluminum is still being researched, due to a limited solubility of the binary system of iron and aluminum causing the formation of hard and brittle intermetallic phases, which decrease the strength and the formability of the dissimilar seam. The presented results show the investigation of laser beam welding for joining different dissimilar hybrid components of the steel materials HX220LAD+Z100, 22MnB5+AS150 and 1.4301, as well as the aluminum alloy AA6016-T4 as a lap joint. Among other things, the influences of the energy per unit length, the material grade, the sheet thickness t, the weld type (lap weld, fillet weld) and the arrangement of the base materials in a lap joint (aluminum-sided irradiation, steel-sided irradiation) on the achievable strengths are analyzed. The characterization of the dissimilar joints includes tensile shear tests and metallographic analyses, depending on the energy per unit length.

  16. Tribology and Tool Wear of Hot Dip Galvanized Zinc Magnesium Alloys on Cold Rolled Steel Sheets

    NASA Astrophysics Data System (ADS)

    Raab, A. E.; Berger, E.; Freudenthaler, J.; Leomann, F.; Walch, C.

    2011-05-01

    Recently zinc based coatings on cold rolled steel with improved functionality in terms of forming and/or corrosion behaviour have been intensively investigated in the steel industry1,2,3. One of the most promising products are zinc magnesium alloys produced in hot dip galvanizing process. These coatings were already introduced in construction industry a few years ago1. With some modifications the improved properties of the coating are also interesting for automotive industry. In the present work the tribological potential of hot dip galvanized zinc magnesium coatings (HDG/ZM) produced at an industrial line under regular production, was studied in terms of sliding properties, adhesive and abrasive tool wear. First a short introduction into surface morphology of HDG/ZM will be given. For the tribological characterization of the material, which is the main topic of the contribution, different tests were performed on hot dip galvanised zinc magnesium material and results were compared with classic hot dip galvanized zinc coating (HDG/Z). The investigations are mainly based on the strip draw test which allows the determination of the friction coefficient directly by using a constant contact pressure. Deep drawing property was tested by forming model cups. The abrasive tool wear was tested using a standard test for material used in automotive industry. The adhesive tool wear was investigated by characterizing the coating material transferred to the tool in the strip draw test. All performed tests show an improved drawability of HDG/ZM compared to classical HDG/Z reference material. However the most promising difference between HDG/ZM and HDG/Z is that galling was found to be less for HDG/ZM than for HDG/Z. Therefore HDG/ZM is an interesting system not only with respect to corrosion protection but also in terms of tribology and provides clear advantages in formability.

  17. Tribology and Tool Wear of Hot Dip Galvanized Zinc Magnesium Alloys on Cold Rolled Steel Sheets

    SciTech Connect

    Raab, A. E.; Berger, E.; Freudenthaler, J.; Leomann, F.; Walch, C.

    2011-05-04

    Recently zinc based coatings on cold rolled steel with improved functionality in terms of forming and/or corrosion behaviour have been intensively investigated in the steel industry. One of the most promising products are zinc magnesium alloys produced in hot dip galvanizing process. These coatings were already introduced in construction industry a few years ago. With some modifications the improved properties of the coating are also interesting for automotive industry. In the present work the tribological potential of hot dip galvanized zinc magnesium coatings (HDG/ZM) produced at an industrial line under regular production, was studied in terms of sliding properties, adhesive and abrasive tool wear.First a short introduction into surface morphology of HDG/ZM will be given. For the tribological characterization of the material, which is the main topic of the contribution, different tests were performed on hot dip galvanised zinc magnesium material and results were compared with classic hot dip galvanized zinc coating (HDG/Z). The investigations are mainly based on the strip draw test which allows the determination of the friction coefficient directly by using a constant contact pressure. Deep drawing property was tested by forming model cups. The abrasive tool wear was tested using a standard test for material used in automotive industry. The adhesive tool wear was investigated by characterizing the coating material transferred to the tool in the strip draw test.All performed tests show an improved drawability of HDG/ZM compared to classical HDG/Z reference material. However the most promising difference between HDG/ZM and HDG/Z is that galling was found to be less for HDG/ZM than for HDG/Z. Therefore HDG/ZM is an interesting system not only with respect to corrosion protection but also in terms of tribology and provides clear advantages in formability.

  18. Capabilities of femtosecond laser ablation ICP-MS for the major, minor, and trace element analysis of high alloyed steels and super alloys.

    PubMed

    Wiltsche, Helmar; Günther, Detlef

    2011-02-01

    Femtosecond laser ablation inductively coupled plasma mass spectrometry was used for the quantification of 23 metallurgical relevant elements in unalloyed, alloyed and highly alloyed steels, and super alloys. It was shown that by using scanning mode ablation with large ablation spot diameters (250 μm), stable and representative sampling can be achieved for the majority of elements, except for bismuth and lead. For Bi and Pb up to 46%, temporal relative standard deviation (TRSD) was encountered, whereas for most other elements, the TRSDs were below 10%. Calibration with matrix-matched and non-matrix-matched standards provided similar agreement within the uncertainty of the certified values. However, the non-matrix-matched standard-based quantification was more influenced by interferences rather than ablation- or excitation-related matrix effects. The method was validated using 34 certified reference materials. (52)Cr, (51)V, or (55)Mn were used as internal standards due to the fact that the Fe concentration was not certified for the majority of reference materials. The determined concentrations for major and minor elements indicate that the total matrix internal standardization (100 wt.%) is applicable, which requires no knowledge about the steel samples prior to analysis.

  19. Irradiation effects on 17-7 PH stainless steel, A-201 carbon steel, and titanium-6-percent-aluminum-4-percent-vanadium alloy

    NASA Technical Reports Server (NTRS)

    Hasse, R. A.; Hartley, C. B.

    1972-01-01

    Irradiation effects on three materials from the NASA Plum Brook Reactor Surveillance Program were determined. An increase of 105 K in the nil-ductility temperature for A-201 steel was observed at a fluence of approximately 3.1 x 10 to the 18th power neutrons/sq cm (neutron energy E sub n greater than 1.0 MeV). Only minor changes in the mechanical properties of 17-7 PH stainless steel were observed up to a fluence of 2 x 10 to the 21st power neutrons/sq cm (E sub n greater than 1.0 MeV). The titanium-6-percent-aluminum-4-percent-vanadium alloy maintained its notch toughness up to a fluence of 1 x 10 to the 21st power neutrons/sq cm (E sub n greater than 1.0 MeV).

  20. Accumulation and annealing of radiation defects under low-temperature electron and neutron irradiation of ODS steel and Fe-Cr alloys

    NASA Astrophysics Data System (ADS)

    Arbuzov, V. L.; Goshchitskii, B. N.; Sagaradze, V. V.; Danilov, S. E.; Kar'kin, A. E.

    2010-10-01

    The processes of accumulation and annealing of radiation defects at low-temperature (77 K) electron and neutron irradiation and their effect on the physicomechanical properties of Fe-Cr alloys and oxide dispersion strengthened (ODS) steel have been studied. It has been shown that the behavior of radiation defects in ODS steel and Fe-Cr alloys is qualitatively similar. Above 250 K, radiation-induced processes of the solid solution decomposition become conspicuous. These processes are much less pronounced in ODS steel because of specific features of its microstructure. Processes related to the overlapping of displacement cascades under neutron irradiation have been considered. It has been shown that, in this case, it is the increase in the size of vacancy clusters, rather than the growth of their concentration, that is prevailing. Possible mechanisms of the radiation hardening of the ODS steel and the Fe-13Cr alloy upon irradiation and subsequent annealing have been discussed.

  1. A case-history analysis of using plain carbon and alloy steel for completion equipment in CO{sub 2} service

    SciTech Connect

    Chitwood, G.B.; Coyle, W.R.; Hilts, R.L.

    1994-12-31

    On rare occasions, field experience has shown that the corrosion rate from exposure to CO{sub 2} can vary greatly among different grades of carbon and alloy steels. The literature attributes the variation in corrosion rate to the microstructure resulting from heat treatment. A normalized plain carbon steel with a pearlitic microstructure is far superior to a hardened and tempered alloy steel with a martensitic microstructure. This paper presents two case histories from oil wells in the Middle East, wherein hardened and tempered alloy steel gas lift equipment underwent severe corrosion from CO{sub 2}. In one case, the API J-55 tubing string experienced no corrosion. This has prompted consideration of the use of normalized steel for completion equipment in order to achieve corrosion performance similar to the J-55 tubing. For the equipment used in these wells, it was determined that alloy steel cannot provide a pearlitic microstructure while still maintaining good metallurgical properties. This study concluded that 9Cr-1 Mo stainless steel has superior corrosion resistance and is recommended for completion equipment in these types of environments.

  2. Gas atomized precursor alloy powder for oxide dispersion strengthened ferritic stainless steel

    SciTech Connect

    Rieken, Joel

    2011-12-13

    Gas atomization reaction synthesis (GARS) was employed as a simplified method for producing precursor powders for oxide dispersion strengthened (ODS) ferritic stainless steels (e.g., Fe-Cr-Y-(Ti,Hf)-O), departing from the conventional mechanical alloying (MA) process. During GARS processing a reactive atomization gas (i.e., Ar-O2) was used to oxidize the powder surfaces during primary break-up and rapid solidification of the molten alloy. This resulted in envelopment of the powders by an ultra-thin (t < 150 nm) metastable Cr-enriched oxide layer that was used as a vehicle for solid-state transport of O into the consolidated microstructure. In an attempt to better understand the kinetics of this GARS reaction, theoretical cooling curves for the atomized droplets were calculated and used to establish an oxidation model for this process. Subsequent elevated temperature heat treatments, which were derived from Rhines pack measurements using an internal oxidation model, were used to promote thermodynamically driven O exchange reactions between trapped films of the initial Cr-enriched surface oxide and internal Y-enriched intermetallic precipitates. This novel microstructural evolution process resulted in the successful formation of nano-metric Y-enriched dispersoids, as confirmed using high energy X-ray diffraction and transmission electron microscopy (TEM), equivalent to conventional ODS alloys from MA powders. The thermal stability of these Y-enriched dispersoids was evaluated using high temperature (1200°C) annealing treatments ranging from 2.5 to 1,000 hrs of exposure. In a further departure from current ODS practice, replacing Ti with additions of Hf appeared to improve the Y-enriched dispersoid thermal stability by means of crystal structure modification. Additionally, the spatial distribution of the dispersoids was found to depend strongly on the original rapidly solidified microstructure. To exploit this, ODS microstructures were engineered from

  3. Gas atomized precursor alloy powder for oxide dispersion strengthened ferritic stainless steel

    NASA Astrophysics Data System (ADS)

    Rieken, Joel Rodney

    Gas atomization reaction synthesis (GARS) was employed as a simplified method for producing precursor powders for oxide dispersion strengthened (ODS) ferritic stainless steels (e.g., Fe-Cr-Y-(Ti,Hf)-O), departing from the conventional mechanical alloying (MA) process. During GARS processing a reactive atomization gas (i.e., Ar-O2) was used to oxidize the powder surfaces during primary break-up and rapid solidification of the molten alloy. This resulted in envelopment of the powders by an ultra-thin (t < 150 nm) metastable Cr-enriched oxide layer that was used as a vehicle for solid-state transport of O into the consolidated microstructure. In an attempt to better understand the kinetics of this GARS reaction, theoretical cooling curves for the atomized droplets were calculated and used to establish an oxidation model for this process. Subsequent elevated temperature heat treatments, which were derived from Rhines pack measurements using an internal oxidation model, were used to promote thermodynamically driven O exchange reactions between trapped films of the initial Cr-enriched surface oxide and internal Y-enriched intermetallic precipitates. This novel microstructural evolution process resulted in the successful formation of nano-metric Y-enriched dispersoids, as confirmed using high energy X-ray diffraction and transmission electron microscopy (TEM), equivalent to conventional ODS alloys from MA powders. The thermal stability of these Y-enriched dispersoids was evaluated using high temperature (1200°C) annealing treatments ranging from 2.5 to 1,000 hrs of exposure. In a further departure from current ODS practice, replacing Ti with additions of Hf appeared to improve the Y-enriched dispersoid thermal stability by means of crystal structure modification. Additionally, the spatial distribution of the dispersoids was found to depend strongly on the original rapidly solidified microstructure. To exploit this, ODS microstructures were engineered from different

  4. Simultaneous first order derivative spectrophotometric determination of vanadium and zirconium in alloy steels and minerals

    NASA Astrophysics Data System (ADS)

    Varghese, Anitha; George, Louis

    2012-09-01

    A simple, selective and sensitive spectrophotometric method has been developed for the individual and simultaneous determination of trace amounts of vanadium(V) and zirconium(IV) in acetic acid medium using a newly synthesised reagent diacetylmonoxime salicyloylhydrazone (DMSH), without any prior separation. The molar absorptivity and Sandell's sensitivity of the coloured species are 1.30 x 104 and 1.82 x 104 Lmol-1cm-1 and 3.9 and 2.5 ng cm-2 for V(V) and Zr(IV), respectively. Beer's law is obeyed between 0.26-2.80 and 0.30-3.20 μg mL-1 concentration of vanadium (V) and zirconium (IV) at 405 and 380 nm respectively. The stoichiometry of the complex was found to be 1:1 (metal:ligand) for V(V) and 1:2 for Zr(IV) complexes. These metal ions interfere with the determination of each other in zero order spectrophotometry. The first derivative spectra of these complexes permitted a simultaneous determination of V(V) and Zr(IV) at zero crossing wavelengths of 445 nm and 405 nm, respectively. The optimum conditions for maximum colour development and other analytical parameters were evaluated. The proposed method has been successfully applied for the determination of zirconium and vanadium in standard alloy steel samples, mineral and soil samples.

  5. Influence of DIT Parameters on the Cementite Spheroidization in a Low-Alloy Medium Carbon Steel

    NASA Astrophysics Data System (ADS)

    Arruabarrena, Jon; López, Beatriz; Rodriguez-Ibabe, Jose M.

    2016-01-01

    The influence of strain, strain rate, and temperature on deformation-induced transformation (DIT) in a low-alloy medium carbon steel is studied. The strain promotes the nucleation of ferrite (deformation-induced ferrite) and also pearlite (deformation-induced pearlite), this last being characterized by a fine interlamellar spacing and morphological instability. At strains ɛ > 0.5, intragranular nucleation activates and further ferrite nucleation over the newly created α/ γ interface takes place, which gives rise to the precipitation of cementite (deformation-induced cementite) at the ferrite boundaries. Soft annealing treatments have been performed on the microstructures obtained by DIT, and the degree of spheroidization has been quantified by image analysis techniques. In comparison to non-deformed conditions, the application of DIT results in a higher degree of spheroidization after soft annealing. Moreover, the EBSD analysis denotes that ferrite grain size refinement is achieved with respect to non-deformed conditions. The degree of spheroidization is highly influenced by the applied strain level and subsequent holding temperature.

  6. Design and analysis of eccentrically braced steel frames with vertical links using shape memory alloys

    NASA Astrophysics Data System (ADS)

    Massah, Saeed Reza; Dorvar, Hosein

    2014-10-01

    In recent years, the philosophy behind traditional methods by which structures were designed to withstand natural disasters has gone through major changes. Shape memory alloys (SMAs) are characterized by their superelastic behavior, which enables them to recover their original shape after experiencing large deformations. This characteristic provides an ideal reversibility capacity that can be used in the passive control of buildings exposed to earthquakes. This article has attempted to identify the effects of changing the hysteretic characteristics of SMA materials when they are used as passive control systems in eccentric bracing frames. By evaluating the numerical analysis results obtained from the modeling of an experimental sample and the modeling of the proposed EBF system, the accuracy of the above-stated notion was confirmed. Moreover, the results that pertain to the nonlinear pushover analysis, time-history dynamic analysis and seismic damage analysis of eccentric steel bracing frames of 4-, 9- and 14-story structures indicate that the use of SMA superelastic materials, in addition to effectively improving their ductility, stiffness and lateral strength, provides an excellent reversibility capacity, which considerably reduces both the maximum relative displacement and the residual deformation in the structure.

  7. Metallurgical and mechanical properties of laser welded high strength low alloy steel

    PubMed Central

    Oyyaravelu, Ramachandran; Kuppan, Palaniyandi; Arivazhagan, Natarajan

    2016-01-01

    The study aimed at investigating the microstructure and mechanical properties of Neodymium-Doped Yttrium Aluminum Garnet (Nd:YAG) laser welded high strength low alloy (HSLA) SA516 grade 70 boiler steel. The weld joint for a 4 mm thick plate was successfully produced using minimum laser power of 2 kW by employing a single pass without any weld preheat treatment. The micrographs revealed the presence of martensite phase in the weld fusion zone which could be due to faster cooling rate of the laser weldment. A good correlation was found between the microstructural features of the weld joints and their mechanical properties. The highest hardness was found to be in the fusion zone of cap region due to formation of martensite and also enrichment of carbon. The hardness results also showed a narrow soft zone at the heat affected zone (HAZ) adjacent to the weld interface, which has no effect on the weld tensile strength. The yield strength and ultimate tensile strength of the welded joints were 338 MPa and 549 MPa, respectively, which were higher than the candidate metal. These tensile results suggested that the laser welding process had improved the weld strength even without any weld preheat treatment and also the fractography of the tensile fractured samples showed the ductile mode of failure. PMID:27222751

  8. Deformation Behavior and TExture Evolution of Steel Alloys under Axial-Torsional Loading

    SciTech Connect

    Siriruk, A.; Kant, M.; Penumadu, D.; Garlea, E.; Vogel, S.

    2011-06-01

    Using hollow cylinder samples with suitable geometry obtained from round bar stock, the deformation behavior of bcc Fe based 12L14 steel alloy is evaluated under multi-axial conditions. A stacked strain gage rosette and extensometer mounted on the cylindrical surface at the mid height of the specimen provided strain tensor as a function of applied stress for pure tensile and torsion tests prior to yielding. This study examines elastic and yield behavior and effects of these with respect to texture evolution. Hollow cylinder specimen geometry (tubes) with small wall thickness and relatively (to its thickness) large inner diameter is used. The variation of observed yield surface in deviatoric plane and the effect on mode of deformation (tension versus torsion versus its combination) on stress-strain behavior is discussed. Bulk texture was studied using neutron time-of-flight diffractometer at High-Pressure-Preferred Orientation (HIPPO) - Los Alamos Neutron Science Center (LANSCE) instrument and the evolution of texture and related anisotropy for pure tension versus torsion are also included.

  9. Changes in electromagnetic properties of a low-alloy steel caused by neutron irradiation

    SciTech Connect

    Goto, Toru; Kamimura, Takeo; Kumano, Shintaro; Takeuchi, Iwao; Maeda, Noriyoshi; Yamaguchi, Atsunori

    1999-10-01

    In order to develop a method for the nondestructive evaluation of material deterioration in nuclear pressure vessels, changes in the electromagnetic properties of the low-alloy steel A533B, Class 1 and its weld metal caused by neutron irradiation up to {approximately}3 {times} 10{sup 23} n/m{sup 2} of neutron fluence at 561 K were measured. Electrical resistance, coercivity and Barkhausen noise were selected as the electromagnetic properties to measure. It was found that decreases of several percent in the readings of electrical resistance and coercivity, and an increase of several percent in the Barkhausen noise occurred due to neutron irradiation. Good correlations between the changes in the electromagnetic properties and those in the mechanical properties were confirmed. Furthermore, an equation using the results of the three tests was found to estimate well the transition temperature and yield strength. From this, the authors conclude that the electromagnetic tests have potential as methods for nondestructive evaluation of material deterioration in the reactor vessels of nuclear power plants.

  10. Erosive Wear Behavior of High-Alloy Cast Iron and Duplex Stainless Steel under Mining Conditions

    NASA Astrophysics Data System (ADS)

    Yoganandh, J.; Natarajan, S.; Kumaresh Babu, S. P.

    2015-09-01

    Centrifugal pumps used in the lignite mines encounter erosive wear problems, leading to a disastrous failure of the pump casings. This paper attempts to evaluate the erosive wear resistance of Ni-Hard 4, high-chromium iron, and Cast CD4MCu duplex stainless steel (DSS), for mining conditions. The prepared test coupons were subjected to an erosion test by varying the impingement velocity and the angle of impingement, under two different pH conditions of 3 and 7, which pertained to the mining conditions. XRD analysis was carried out to confirm the phases present in the alloy. The eroded surface was subjected to SEM analysis to identify the erosion mechanisms. The surface degradation of Ni-Hard 4 and high-chromium iron came from a low-angle abrasion with a grooving and plowing mechanism at a low angle of impingement. At normal impingement, deep indentations resulted in lips and crater formations, leading to degradation of the surface in a brittle manner. A combined extrusion-forging mechanism is observed in the CD4MCu DSS surface at all the impingement angles.

  11. Ultrasonic attenuation peak in steel and aluminum alloy during rotating bending fatigue

    NASA Astrophysics Data System (ADS)

    Ogi, Hirotsugu; Hamaguchi, Takayuki; Hirao, Masahiko

    2000-04-01

    Using electromagnetic acoustic resonance (EMAR), we studied the evolution of the surface shearwave attenuation and phase velocity in a 0.45 pct C steel and a 5052 aluminum alloy exposed to rotating bending fatigue. In the EMAR method, we used electromagnetic acoustic transducers (EMATs) for the contactless measurements of the axial shear wave, which is a surface shear wave that propagates along a cylindrical surface in the circumferential direction, with an axial polarization. There has been no previous report of continuous and contactless monitoring of the surface wave attenuation and velocity being performed without interrupting the fatigue. The attenuation coefficient always showed sharp peaks around 90 pct of the fatigue life, independent of the fatigue-stress amplitude. To interpret this phenomenon, we made crack-growth observations using replicas and measurements of recovery of attenuation and velocity by stopping the cyclic loading before and after the peak. From these results, we concluded that the evolution of the ultrasonic properties is caused by a drastic change in dislocation mobility being accompanied by the crack growth at the final stage of the fatigue life.

  12. Constitutive equations of a ballistic steel alloy as a function of temperature

    NASA Astrophysics Data System (ADS)

    Berkovic, L.; Chabotier, A.; Coghe, F.; Rabet, L.

    2012-08-01

    In the present work, dynamic tests have been performed on a new ballistic steel alloy by means of split Hopkinson pressure bars (SHPB). The impact behavior was investigated for strain rates ranging from 1000 to 2500 s-1, and temperatures in the range from - 196 to 300∘C. A robotized sample device was developed for transferring the sample from the heating or cooling device to the position between the bars. Simulations of the temperature evolution and its distribution in the specimen were performed using the finite element method. Measurements with thermocouples added inside the sample were carried out in order to validate the FEM simulations. The results show that a thermal gradient is present inside the sample; the average temperature loss during the manipulation of the sample is evaluated. In a last stage, optimal material constants for different constitutive models (Johnson-Cook, Zerilli-Amstrong, Cowper-Symonds) has been computed by fitting, in a least square sense, the numerical and experimental stress-strain curves. They have been implemented in a hydrocode for validation using a simple impact problem: an adapted projectile geometry with a truncated nose (.50 calibre fragment simulating projectiles) was fired directly against an armor plate. The parameters of the selected strength and failure models were determined. There is a good correspondence between the experimental and computed results. Nevertheless, an improved failure model is necessary to get satisfactory computed residual projectile velocities.

  13. Survey of the literature on low-alloy steel fastener corrosion in PWR power plants

    SciTech Connect

    Hall, J.F.

    1984-12-01

    This report presents the results of a literature survey of low alloy steel fastener corrosion in PWR applications. The report addresses boric acid corrosion (accelerated general corrosion) and stress corrosion cracking of threaded fasteners used in primary pressure boundary closures, in secondary, auxiliary, and safety system closures and in component support applications. The report reviews and summarizes corrosion events that have occurred in domestic PWRs since 1968. Information provided for each event includes plant identification, year of event, major component or part affected, fastener material, fastener diameter, number of corroded studs, the service environments, the number of degraded fasteners and the results of post-service failure analyses. Possible corrective actions that are available to eliminate or mitigate the effects of the two types of corrosion are also identified. Laboratory test data, including some recent unpublished data, that are related to fastener corrosion are also discussed. The report also includes recommended additional work in the areas of boric acid corrosion, stress corrosion cracking and analytical methodologies to solve these fastener corrosion problems.

  14. Green superlubricity of Nitinol 60 alloy against steel in presence of castor oil

    NASA Astrophysics Data System (ADS)

    Zeng, Qunfeng; Dong, Guangneng; Martin, Jean Michel

    2016-07-01

    In the present work, first, we show that sliding Nitinol 60 alloy against steel under castor oil lubrication exhibits a new case of superlubricity (coefficient of friction CoF ≪ 0.01). So far, CoF below 0.01 have never been achieved under boundary lubrication at high contact pressure and in presence of vegetable oil as a green lubricant. Next, it is demonstrated that superlubricity is controlled by tribochemical reactions, involving chemical degradation of castor oil and the formation of metal oxy-hydroxides. Finally, to explain these findings, we propose a novel superlubricity mechanism consisting of hexanoic acid molecules intercalated between nickel and iron oxy-hydroxide lamellar layers, a structure very similar to the one found in Fe-Ni batteries. We propose that superlubricity is achieved due to repulsive electrostatic forces acting between the intercalated metal oxy-hydroxide lamellar compounds. This system would be suitable for practical engineering applications in many fields including biotechnologies.

  15. Detection of radiation damage in low alloy steel using a SQUID sensor

    SciTech Connect

    Otaka, Masahiro; Shimizu, Sadato; Morinaka, Ren; Maeda, Noriyoshi; Yamaguchi, Atsunori

    1999-10-01

    The magnetic properties of A533B low alloy steel irradiated up to 3 {times} 10{sup 23} n/m{sup 2} in a nuclear reactor were measured using a SQUID sensor. The SQUID sensor used in the test is the type with a first-order axial gradiometer. Test specimens were irradiated to 0.5 {times} 10{sup 23} and 3.0 {times} 10{sup 23} n/m{sup 2}, and then magnetized in a 0.2 T field until saturation before measurement. The specimens were put on a scanning table in a hot laboratory and the SQUID output was recorded while each specimen was gradually moved in a horizontal direction under the SQUID sensor. A superconducting magnet was used to put the test specimen under a magnetic field that changed from +0.01 T to {minus}0.01 T to observe the relation between magnetic field intensity and coercive force (B-H curve). The B-H curve shows a definite tendency towards a higher coercive force for test specimens with higher neutron fluence. The test result also shows a good relation between mechanical properties, such as yield strength, tensile strength, and the Charpy impact test result, with SQUID output. This proves that there is a very good change of developing a non-destructive evaluation system for nuclear reactor structure. This kind of evaluation system would be a great help in making plant life management even more reliable and reasonable.

  16. Effect of the La alloying addition on the antibacterial capability of 316L stainless steel.

    PubMed

    Yuan, J P; Li, W; Wang, C

    2013-01-01

    316L stainless steel is widely used for fashion jewelry but it can carry a large number of bacteria and cause the potential risk of infection since it has no antimicrobial ability. In this paper, La is used as an alloying addition. The antibacterial capability, corrosion resistance and processability of the La-modified 316L are investigated by microscopic observation, thin-film adhering quantitative bacteriostasis, electrochemical measurement and mechanical test. The investigations reveal that the La-containing 316L exhibits the Hormesis effect against Staphylococcus aureus ATCC 25923 and Escherichia coli DH5α, 0.05 wt.% La stimulates their growth, as La increases, the modified 316L exhibits the improved antibacterial effect. The more amount of La is added, the better antibacterial ability is achieved, and 0.42 wt.% La shows excellent antibacterial efficacy. No more than 0.11 wt.% La addition improves slightly the corrosion resistance in artificial sweat and has no observable impact on the processability of 316L, while a larger La content degrades them. Therefore, the addition of La alone in 316L is difficult to obtain the optimal combination of corrosion resistance, antibacterial capability and processability. In spite of that, 0.15 wt.% La around is inferred to be the trade-off for the best overall performance.

  17. Green superlubricity of Nitinol 60 alloy against steel in presence of castor oil

    PubMed Central

    Zeng, Qunfeng; Dong, Guangneng; Martin, Jean Michel

    2016-01-01

    In the present work, first, we show that sliding Nitinol 60 alloy against steel under castor oil lubrication exhibits a new case of superlubricity (coefficient of friction CoF ≪ 0.01). So far, CoF below 0.01 have never been achieved under boundary lubrication at high contact pressure and in presence of vegetable oil as a green lubricant. Next, it is demonstrated that superlubricity is controlled by tribochemical reactions, involving chemical degradation of castor oil and the formation of metal oxy-hydroxides. Finally, to explain these findings, we propose a novel superlubricity mechanism consisting of hexanoic acid molecules intercalated between nickel and iron oxy-hydroxide lamellar layers, a structure very similar to the one found in Fe-Ni batteries. We propose that superlubricity is achieved due to repulsive electrostatic forces acting between the intercalated metal oxy-hydroxide lamellar compounds. This system would be suitable for practical engineering applications in many fields including biotechnologies. PMID:27444211

  18. Laser-Arc Hybrid Welding of Dissimilar Titanium Alloy and Stainless Steel Using Copper Wire

    NASA Astrophysics Data System (ADS)

    Gao, Ming; Chen, Cong; Wang, Lei; Wang, Zemin; Zeng, Xiaoyan

    2015-05-01

    Laser-arc hybrid welding with Cu3Si filler wire was employed to join dissimilar Ti6Al4V titanium alloy and AISI316 stainless steel (316SS). The effects of welding parameters on bead shape, microstructure, mechanical properties, and fracture behavior were investigated in detail. The results show that cross-weld tensile strength of the joints is up to 212 MPa. In the joint, obvious nonuniformity of the microstructure is found in the fusion zone (FZ) and at the interfaces from the top to the bottom, which could be improved by increasing heat input. For the homogeneous joint, the FZ is characterized by Fe67- x Si x Ti33 dendrites spreading on α-Cu matrix, and the two interfaces of 316SS/FZ and FZ/Ti6Al4V are characterized by a bamboo-like 316SS layer and a CuTi2 layer, respectively. All the tensile samples fractured in the hardest CuTi2 layer at Ti6Al4V side of the joints. The fracture surface is characterized by river pattern revealing brittle cleavage fracture. The bead formation mechanisms were discussed according to the melt flow and the thermodynamic calculation.

  19. Determination of the continuous cooling transformation diagram of a high strength low alloyed steel

    NASA Astrophysics Data System (ADS)

    Kang, Hun Chul; Park, Bong June; Jang, Ji Hun; Jang, Kwang Soon; Lee, Kyung Jong

    2016-11-01

    The continuous cooling transformation diagram of a high strength low alloyed steel was determined by a dilatometer and microscopic analysis (OM, SEM) as well as thermodynamic analysis. As expected, Widmanstätten ferrite, bainite and martensite coexisted for most cooling rates, which made it difficult to determine the transformation kinetics of individual phases. However, peaks were clearly observed in the dilatometric {d( {LVDT} )}/{dT} curves. By overlapping the {d( {LVDT} )}/{dT} curves, which were determined using various cooling rates, peaks were separated and the peak rate temperatures, as well as the temperature at the start of transformation (5%) and the end of transformation (95%) of an individual phase, were determined. A SEM analysis was also conducted to identify which phase existed and to quantify the volume fraction of each phase. It was confirmed that the additional {d( {LVDT} )}/{dT} curve analysis described the transformation behavior more precisely than the conventional continuous cooling transformation diagram, as determined by the volume measured from the microstructure analysis.

  20. Green superlubricity of Nitinol 60 alloy against steel in presence of castor oil.

    PubMed

    Zeng, Qunfeng; Dong, Guangneng; Martin, Jean Michel

    2016-07-21

    In the present work, first, we show that sliding Nitinol 60 alloy against steel under castor oil lubrication exhibits a new case of superlubricity (coefficient of friction CoF ≪ 0.01). So far, CoF below 0.01 have never been achieved under boundary lubrication at high contact pressure and in presence of vegetable oil as a green lubricant. Next, it is demonstrated that superlubricity is controlled by tribochemical reactions, involving chemical degradation of castor oil and the formation of metal oxy-hydroxides. Finally, to explain these findings, we propose a novel superlubricity mechanism consisting of hexanoic acid molecules intercalated between nickel and iron oxy-hydroxide lamellar layers, a structure very similar to the one found in Fe-Ni batteries. We propose that superlubricity is achieved due to repulsive electrostatic forces acting between the intercalated metal oxy-hydroxide lamellar compounds. This system would be suitable for practical engineering applications in many fields including biotechnologies.

  1. Ultrasonic attenuation peak in steel and aluminum alloy during rotating bending fatigue

    SciTech Connect

    Ogi, Hirotsugu; Hamaguchi, Takayuki; Hirao, Masahiko

    2000-04-01

    Using electromagnetic acoustic resonance (EMAR), the authors studied the evolution of the surface shear wave attenuation and phase velocity in a 0.45 pct C steel and a 5052 aluminum alloy exposed to rotating bending fatigue. In the EMAR method, they used electromagnetic acoustic transducers (EMATs) for the contactless measurements of the axial shear wave, which is a surface shear wave that propagates along a cylindrical surface in the circumferential direction, with an axial polarization. There has been no precious report of continuous and contactless monitoring of the surface wave attenuation and velocity being performed without interrupting the fatigue. The attenuation coefficient always showed sharp peaks around 90 pct of the fatigue life, independent of the fatigue-stress amplitude. To interpret this phenomenon, the authors made crack-growth observations using replicas and measurements of recovery of attenuation and velocity by stopping the cyclic loading before and after the peak. From these results, they concluded that the evolution of the ultrasonic properties is caused by a drastic change in dislocation mobility being accompanied by the crack growth at the final stage of the fatigue life.

  2. Evaluation of Alumina-Forming Austenitic Stainless Steel Alloys in Microturbines

    SciTech Connect

    Brady, M.P.; Matthews, W.J.

    2010-09-15

    Oak Ridge National Laboratory (ORNL) and Capstone Turbine Corporation (CTC) participated in an in-kind cost share cooperative research and development agreement (CRADA) effort under the auspices of the Energy Efficiency and Renewable Energy (EERE) Technology Maturation Program to explore the feasibility for use of developmental ORNL alumina-forming austenitic (AFA) stainless steels as a material of construction for microturbine recuperator components. ORNL delivered test coupons of three different AFA compositions to CTC. The coupons were exposed in steady-state elevated turbine exit temperature (TET) engine testing, with coupons removed for analysis after accumulating ~1,500, 3,000, 4,500, and 6,000 hours of operation. Companion test coupons were also exposed in oxidation testing at ORNL at 700-800°C in air with 10% H2O. Post test assessment of the coupons was performed at ORNL by light microscopy and electron probe microanalysis. The higher Al and Nb containing AFA alloys exhibited excellent resistance to oxidation/corrosion, and thus show good promise for recuperator applications.

  3. Modeling the post-yield flow behavior after neutron and electron irradiation of steels and iron-base alloys.

    SciTech Connect

    Dimelfi, R. J.

    1999-01-13

    Irradiation hardening is an issue of practical importance as it relates to the remanent life and the nature of failure of reactor components exposed to displacement-producing radiation. For example, irradiation-induced yield strength increases in pressure vessel steels are directly related to increases in the ductile-to-brittle-transition-temperature of these materials. Other issues associated with hardening, such as reductions in ductility, toughness and fatigue life of structural steels are also of concern. Understanding these phenomena requires studies of fundamental microstructural mechanisms of hardening. Because of the limited supply of neutron-irradiated surveillance material, difficulties posed by the radioactivity of neutron-exposed samples and the uncertainty of irradiation conditions in this case, fundamental studies are often conducted using well-controlled experiments involving irradiation by electrons instead of neutrons. Also, in such studies, simple model alloys are used in place of steels to focus on the influence of specific alloy constituents. It is, therefore, important to understand the relationship between the results of this kind of experiment and the effects of in-reactor neutron exposure in order to use them to make predictions of significance to reactor component life. In this paper, we analyze the tensile behavior of pressure vessel steels (A212B and A350) irradiated by neutrons and electrons. The results show that the post-yield true stress/true strain behavior can provide fingerprints of the different hardening effects that result from irradiation by the two particles, which also reflect the influence of alloy content. Microstructurally-based models for irradiation-induced yield strength increases, combined with a model for strain hardening, are used to make predictions of the different effects of irradiation by the two particles on the entire flow curve that agree well with data.

  4. A comparative assessment of the fracture toughness behavior of ferritic-martensitic steels and nanostructured ferritic alloys

    NASA Astrophysics Data System (ADS)

    Byun, Thak Sang; Hoelzer, David T.; Kim, Jeoung Han; Maloy, Stuart A.

    2017-02-01

    The Fe-Cr alloys with ultrafine microstructures are primary candidate materials for advanced nuclear reactor components because of their excellent high temperature strength and high resistance to radiation-induced damage such as embrittlement and swelling. Mainly two types of Fe-Cr alloys have been developed for the high temperature reactor applications: the quenched and tempered ferritic-martensitic (FM) steels hardened primarily by ultrafine laths and carbonitrides and the powder metallurgy-based nanostructured ferritic alloys (NFAs) by nanograin structure and nanoclusters. This study aims at elucidating the differences and similarities in the temperature and strength dependences of fracture toughness in the Fe-Cr alloys to provide a comparative assessment of their high-temperature structural performance. The KJQ versus yield stress plots confirmed that the fracture toughness was inversely proportional to yield strength. It was found, however, that the toughness data for some NFAs were outside the band of the integrated dataset at given strength level, which indicates either a significant improvement or deterioration in mechanical properties due to fundamental changes in deformation and fracture mechanisms. When compared to the behavior of NFAs, the FM steels have shown much less strength dependence and formed narrow fracture toughness data bands at a significantly lower strength region. It appeared that at high temperatures ≥600 °C the NFAs cannot retain the nanostructure advantage of high strength and high toughness either by high-temperature embrittlement or by excessive loss of strength. Irradiation studies have revealed, however, that the NFAs have much stronger radiation resistance than tempered martensitic steels, such as lower radiation-induced swelling, finer helium bubble formation, lower irradiation creep rate and reduced low temperature embrittlement.

  5. Study of magnetism in Ni-Cr hardface alloy deposit on 316LN stainless steel using magnetic force microscopy

    NASA Astrophysics Data System (ADS)

    Kishore, G. V. K.; Kumar, Anish; Chakraborty, Gopa; Albert, S. K.; Rao, B. Purna Chandra; Bhaduri, A. K.; Jayakumar, T.

    2015-07-01

    Nickel base Ni-Cr alloy variants are extensively used for hardfacing of austenitic stainless steel components in sodium cooled fast reactors (SFRs) to avoid self-welding and galling. Considerable difference in the compositions and melting points of the substrate and the Ni-Cr alloy results in significant dilution of the hardface deposit from the substrate. Even though, both the deposit and the substrate are non-magnetic, the diluted region exhibits ferromagnetic behavior. The present paper reports a systematic study carried out on the variations in microstructures and magnetic behavior of American Welding Society (AWS) Ni Cr-C deposited layers on 316 LN austenitic stainless steels, using atomic force microscopy (AFM) and magnetic force microscopy (MFM). The phase variations of the oscillations of a Co-Cr alloy coated magnetic field sensitive cantilever is used to quantitatively study the magnetic strength of the evolved microstructure in the diluted region as a function of the distance from the deposit/substrate interface, with the spatial resolution of about 100 nm. The acquired AFM/MFM images and the magnetic property profiles have been correlated with the variations in the chemical compositions in the diluted layers obtained by the energy dispersive spectroscopy (EDS). The study indicates that both the volume fraction of the ferromagnetic phase and its ferromagnetic strength decrease with increasing distance from the deposit/substrate interface. A distinct difference is observed in the ferromagnetic strength in the first few layers and the ferromagnetism is observed only near to the precipitates in the fifth layer. The study provides a better insight of the evolution of ferromagnetism in the diluted layers of Ni-Cr alloy deposits on stainless steel.

  6. A comparative assessment of the fracture toughness behavior of ferritic-martensitic steels and nanostructured ferritic alloys

    DOE PAGES

    Byun, Thak Sang; Hoelzer, David T.; Kim, Jeoung Han; ...

    2016-12-07

    The Fe-Cr alloys with ultrafine microstructures are primary candidate materials for advanced nuclear reactor components because of their excellent high temperature strength and high resistance to radiation-induced damage such as embrittlement and swelling. Mainly two types of Fe-Cr alloys have been developed for the high temperature reactor applications: the quenched and tempered ferritic-martensitic (FM) steels hardened primarily by ultrafine laths and carbonitrides and the powder metallurgy-based nanostructured ferritic alloys (NFAs) by nanograin structure and nanoclusters. This paper aims at elucidating the differences and similarities in the temperature and strength dependences of fracture toughness in the Fe-Cr alloys to provide amore » comparative assessment of their high-temperature structural performance. The KJQ versus yield stress plots confirmed that the fracture toughness was inversely proportional to yield strength. It was found, however, that the toughness data for some NFAs were outside the band of the integrated dataset at given strength level, which indicates either a significant improvement or deterioration in mechanical properties due to fundamental changes in deformation and fracture mechanisms. When compared to the behavior of NFAs, the FM steels have shown much less strength dependence and formed narrow fracture toughness data bands at a significantly lower strength region. It appeared that at high temperatures ≥600 °C the NFAs cannot retain the nanostructure advantage of high strength and high toughness either by high-temperature embrittlement or by excessive loss of strength. Finally, irradiation studies have revealed, however, that the NFAs have much stronger radiation resistance than tempered martensitic steels, such as lower radiation-induced swelling, finer helium bubble formation, lower irradiation creep rate and reduced low temperature embrittlement.« less

  7. A comparative assessment of the fracture toughness behavior of ferritic-martensitic steels and nanostructured ferritic alloys

    SciTech Connect

    Byun, Thak Sang; Hoelzer, David T.; Kim, Jeoung Han; Maloy, Stuart A.

    2016-12-07

    The Fe-Cr alloys with ultrafine microstructures are primary candidate materials for advanced nuclear reactor components because of their excellent high temperature strength and high resistance to radiation-induced damage such as embrittlement and swelling. Mainly two types of Fe-Cr alloys have been developed for the high temperature reactor applications: the quenched and tempered ferritic-martensitic (FM) steels hardened primarily by ultrafine laths and carbonitrides and the powder metallurgy-based nanostructured ferritic alloys (NFAs) by nanograin structure and nanoclusters. This paper aims at elucidating the differences and similarities in the temperature and strength dependences of fracture toughness in the Fe-Cr alloys to provide a comparative assessment of their high-temperature structural performance. The KJQ versus yield stress plots confirmed that the fracture toughness was inversely proportional to yield strength. It was found, however, that the toughness data for some NFAs were outside the band of the integrated dataset at given strength level, which indicates either a significant improvement or deterioration in mechanical properties due to fundamental changes in deformation and fracture mechanisms. When compared to the behavior of NFAs, the FM steels have shown much less strength dependence and formed narrow fracture toughness data bands at a significantly lower strength region. It appeared that at high temperatures ≥600 °C the NFAs cannot retain the nanostructure advantage of high strength and high toughness either by high-temperature embrittlement or by excessive loss of strength. Finally, irradiation studies have revealed, however, that the NFAs have much stronger radiation resistance than tempered martensitic steels, such as lower radiation-induced swelling, finer helium bubble formation, lower irradiation creep rate and reduced low temperature embrittlement.

  8. Laser surface alloying of FeCoCrAlNi high-entropy alloy on 304 stainless steel to enhance corrosion and cavitation erosion resistance

    NASA Astrophysics Data System (ADS)

    Zhang, S.; Wu, C. L.; Zhang, C. H.; Guan, M.; Tan, J. Z.

    2016-10-01

    FeCoCrAlNi high-entropy alloy coating was synthesized with premixed high-purity Co, Cr, Al and Ni powders on 304 stainless steel by laser surface alloying, aiming at improving corrosion and cavitation erosion resistance. Phase constituents, microstructure and microhardness were investigated using XRD, SEM, and microhardness tester, respectively. The cavitation erosion and electrochemical corrosion behavior of FeCoCrAlNi coating in 3.5% NaCl solution were also evaluated using an ultrasonic vibrator and potentiodynamic polarization measurement. Experimental results showed that with appropriate laser processing parameters, FeCoCrAlNi coating with good metallurgical bonding to the substrate could be achieved. FeCoCrAlNi coating was composed of a single BCC solid solution. The formation of simple solid solutions in HEAs was the combined effect of mixing entropy (ΔSmix), mixing enthalpy (ΔHmix), atom-size difference (δ) and valence electron concentration (VEC), and the effect of ΔSmix was much larger than that of the other factors. The microhardness of the FeCoCrAlNi coating was ~3 times that of the 304 stainless steel. Both the corrosion and cavitation erosion resistance of the coating were improved. The cavitation erosion resistance for FeCoCrAlNi HEA coating was ~7.6 times that of 304 stainless steel. The corrosion resistance was also improved as reflected by a reduction in the current density of one order of magnitude as compared with 304 stainless steel.

  9. Dissimilar Laser Welding/Brazing of 5754 Aluminum Alloy to DP 980 Steel: Mechanical Properties and Interfacial Microstructure

    NASA Astrophysics Data System (ADS)

    Yang, Jin; Li, Yulong; Zhang, Hua; Guo, Wei; Weckman, David; Zhou, Norman

    2015-11-01

    A diode laser welding/brazing technique was used for lap joining of 5754 aluminum alloy to DP 980 steel with Al-Si filler metal. The correlation between joint interfacial microstructure, wettability of filler metal, and mechanical properties was systematically investigated. At low laser power (1.4 kW), a layer of intermetallic compounds, composed of θ-Fe(Al,Si)3 and τ 5 -Al7.2Fe1.8Si, was observed at the interface between fusion zone and steel. Because of the poor wettability of filler metal on the steel substrate, the joint strength was very low and the joint failed at the FZ/steel interface. When medium laser power (2.0 kW) was applied, the wettability of filler metal was enhanced, which improved the joint strength and led to FZ failure. With further increase of laser power to 2.6 kW, apart from θ and τ 5, a new hard and brittle η-Fe2(Al,Si)5 IMC with microcracks was generated at the FZ/steel interface. The formation of η significantly degraded the joint strength. The failure mode changed back to interfacial failure.

  10. Frictional behaviors of some nitrogen ceramics in conformal contact with tin coated Al-Si alloy, steel and MMC

    NASA Astrophysics Data System (ADS)

    Wang, Q.; Cheng, H. S.; Fine, M. E.

    1994-07-01

    The frictional behavior of certain nitrogen-containing ceramics, such as silicon nitride, alpha sialons, and beta sialons as journal materials were studied in conformal contact with a tin-coated Al-Si alloy (Al-Si/Sn), forged 1141 steel and a cast aluminum matrix composite with silicon carbide reinforcement (cast metal matrix composites (MMC)) as bearing materials while lubricated with SAE 10W30. A case-hardened 1016 steel was also tested with the Al-Si/Sn and cast MMC bearings under the same conditions. The friction values of the ceramic and the steel journal wear pairs were compared and their frictional behaviors were evaluated. Silicon nitride and one of the beta sialons exhibited higher load-supporting capacities than the others when they were in contact with the 1141 steel bearings. The journal surface roughness was found to be very important when the journals were in contact with the Al-Si/Sn bearings. The frictional behavior of the ceramics and cast MMC pairs and the steel and cast MMC pairs were controlled by different wear machanisms, namely for the former, hard particle pull-out and matrix plowing, and for the latter, iron transfer from the journal to the cast MMC bearing surface.

  11. Effect of confining pressure due to external jacket of steel plate or shape memory alloy wire on bond behavior between concrete and steel reinforcing bars.

    PubMed

    Choi, Eunsoo; Kim, Dongkyun; Park, Kyoungsoo

    2014-12-01

    For external jackets of reinforced concrete columns, shape memory alloy (SMA) wires are easy to install, and they provide active and passive confining pressure; steel plates, on the other hand, only provide passive confining pressure, and their installation on concrete is not convenient because of the requirement of a special device. To investigate how SMA wires distinctly impact bond behavior compared with steel plates, this study conducted push-out bond tests of steel reinforcing bars embedded in concrete confined by SMA wires or steel plates. For this purpose, concrete cylinders were prepared with dimensions of 100 mm x 200 mm, and D-22 reinforcing bars were embedded at the center of the concrete cylinders. External jackets of 1.0 mm and 1.5 mm thickness steel plates were used to wrap the concrete cylinders. Additionally, NiTiNb SMA wire with a diameter of 1.0 mm was wound around the concrete cylinders. Slip of the reinforcing bars due to pushing force was measured by using a displacement transducer, while the circumferential deformation of specimens was obtained by using an extensometer. The circumferential deformation was used to calculate the circumferential strains of the specimens. This study assessed the radial confining pressure due to the external jackets on the reinforcing bars at bond strength from bond stress-slip curves and bond stress-circumferential strain curves. Then, the effects of the radial confining pressure on the bond behavior of concrete are investigated, and an equation is suggested to estimate bond strength using the radial confining pressure. Finally, this study focused on how active confining pressure due to recovery stress of the SMA wires influences bond behavior.

  12. Constitutive Modeling of High-Temperature Flow Behavior of an Nb Micro-alloyed Hot Stamping Steel

    NASA Astrophysics Data System (ADS)

    Zhang, Shiqi; Feng, Ding; Huang, Yunhua; Wei, Shizhong; Mohrbacher, Hardy; Zhang, Yue

    2016-03-01

    The thermal deformation behavior and constitutive models of an Nb micro-alloyed 22MnB5 steel were investigated by conducting isothermal uniaxial tensile tests at the temperature range of 873-1223 K with strain rates of 0.1-10 s-1. The results indicated that the investigated steel showed typical work hardening and dynamic recovery behavior during hot deformation, and the flow stress decreased with a decrease in strain rate and/or an increase in temperature. On the basis of the experimental data, the modified Johnson-Cook (modified JC), modified Norton-Hoff (modified NH), and Arrhenius-type (AT) constitutive models were established for the subject steel. However, the flow stress values predicted by these three models revealed some remarkable deviations from the experimental values for certain experimental conditions. Therefore, a new combined modified Norton-Hoff and Arrhenius-type constitutive model (combined modified NH-AT model), which accurately reflected both the work hardening and dynamic recovery behavior of the subject steel, was developed by introducing the modified parameter k ɛ. Furthermore, the accuracy of these constitutive models was assessed by the correlation coefficient, the average absolute relative error, and the root mean square error, which indicated that the flow stress values computed by the combined modified NH-AT model were highly consistent with the experimental values (R = 0.998, AARE = 1.63%, RMSE = 3.85 MPa). The result confirmed that the combined modified NH-AT model was suitable for the studied Nb micro-alloyed hot stamping steel. Additionally, the practicability of the new model was also verified using finite element simulations in ANSYS/LS-DYNA, and the results confirmed that the new model was practical and highly accurate.

  13. On the use of temperature dependences of the coercive force for an analysis of structural and phase changes that occur upon tempering of alloy carbon steels

    NASA Astrophysics Data System (ADS)

    Ul'yanov, A. I.; Baranova, I. A.; Chulkina, A. A.; Zagainov, A. V.; Volkov, V. A.

    2014-05-01

    The effect of alloying elements Mn, Cr, and Si on the magnetic hysteresis properties of cementite and model steels with a carbon concentration of 0.6 wt % has been studied. It has been shown that alloying with carbide-forming elements (Mn, Cr) reduces the coercive force and the Curie temperature of cementite. Measurements of the temperature dependences of the coercive force of the model steels with carbon content of 0.6 wt % alloyed with manganese, chromium, or silicon have been performed in the temperature range of -196 to +300°C. It has been established that the local maximum of the coercive force of these steels in this temperature range coincides with the Curie point of the precipitates of the carbide phases. Based on an analysis of the temperature dependences of the coercive force, the content of the alloying element in the precipitates of cementite of steels tempered at different temperatures has been estimated. It has been shown that the character of the dependence of the coercive force of alloy steels on the temperature of tempering in the temperature range of 250-700°C is mainly determined by the coercivity and by the kinetics of the formation of cementite precipitates.

  14. Ultrasonic Spot Welding of Aluminum to High-Strength Low-Alloy Steel: Microstructure, Tensile and Fatigue Properties

    NASA Astrophysics Data System (ADS)

    Patel, V. K.; Bhole, S. D.; Chen, D. L.

    2014-04-01

    The structural applications of lightweight aluminum alloys inevitably involve dissimilar welding with steels and the related durability issues. This study was aimed at evaluating the microstructural change, lap shear tensile load, and fatigue resistance of dissimilar ultrasonic spot-welded joints of aluminum-to-galvanized high-strength low-alloy (HSLA) steel. Two non-uniform layers were identified in between Al and HSLA steel via SEM/EDS and XRD. One was an Al-Zn eutectic layer and the other was a thin (<2 μm) layer of intermetallic compound (IMC) of Al and Fe in the nugget zone. The lap shear tensile testing gave a maximum load of 3.7 kN and the sample failed initially in between the Al-Zn eutectic film and Al-Fe IMC, and afterward from the region containing Al on both matching fracture surfaces. The fatigue test results showed a fatigue limit of about 0.5 kN (at 1 × 107 cycles). The maximum cyclic stress at which transition of the fatigue fracture from transverse through-thickness crack growth mode to the interfacial failure mode occurs increases with increasing energy input.

  15. Hydrogen adsorption and diffusion, and subcritical-crack growth in high strength steels and nickel base alloys

    NASA Technical Reports Server (NTRS)

    Wei, R. P.; Klier, K.; Simmons, G. W.; Chornet, E.

    1973-01-01

    Embrittlement, or the enhancement of crack growth by gaseous hydrogen in high strength alloys, is of primary interest in selecting alloys for various components in the space shuttle. Embrittlement is known to occur at hydrogen gas pressures ranging from fractions to several hundred atmospheres, and is most severe in the case of martensitic high strength steels. Kinetic information on subcritical crack growth in gaseous hydrogen is sparse at this time. Corroborative information on hydrogen adsorption and diffusion is inadequate to permit a clear determination of the rate controlling process and possible mechanism in hydrogen enhanced crack growth, and for estimating behavior over a range of temperatures and pressures. Therefore, coordinated studies of the kinetics of crack growth, and adsorption and diffusion of hydrogen, using identical materials, have been initiated. Comparable conditions of temperature and pressure will be used in the chemical and mechanical experiments. Inconel 718 alloy and 18Ni(200) maraging steel have been selected for these studies. Results from these studies are expected to provide not only a better understanding of the gaseous hydrogen embrittlement phenomenon itself, but also fundamental information on hydrogen adsorption and diffusion, and crack growth information that can be used directly for design.

  16. Laser surface alloying of 316L stainless steel coated with a bioactive hydroxyapatite-titanium oxide composite.

    PubMed

    Ghaith, El-Sayed; Hodgson, Simon; Sharp, Martin

    2015-02-01

    Laser surface alloying is a powerful technique for improving the mechanical and chemical properties of engineering components. In this study, laser surface irradiation process employed in the surface modification off 316L stainless steel substrate using hydroxyapatite-titanium oxide to provide a composite ceramic layer for the suitability of applying this technology to improve the biocompatibility of medical alloys and implants. Fusion of the metal surface incorporating hydroxyapatite-titania ceramic particles using a 30 W Nd:YAG laser at different laser powers, 40, 50 and 70% power and a scan speed of 40 mm s(-1) was observed to adopt the optimum condition of ceramic deposition. Coatings were evaluated in terms of microstructure, surface morphology, composition biocompatibility using XRD, ATR-FTIR, SEM and EDS. Evaluation of the in vitro bioactivity by soaking the treated metal in SBF for 10 days showed the deposition of biomimetic apatite.

  17. Atomic scale investigation of redistribution of alloying elements in pearlitic steel wires upon cold-drawing and annealing.

    PubMed

    Li, Y J; Choi, P; Goto, S; Borchers, C; Raabe, D; Kirchheim, R

    2013-09-01

    A local electrode atom probe has been employed to analyze the redistribution of alloying elements including Si, Mn, and Cr in pearlitic steel wires upon cold-drawing and subsequent annealing. It has been found that the three elements undergo mechanical mixing upon cold-drawing at large strains, where Mn and Cr exhibit a nearly homogeneous distribution throughout both ferrite and cementite, whereas Si only dissolves slightly in cementite. Annealing at elevated temperatures leads to a reversion of the mechanical alloying. Si atoms mainly segregate at well-defined ferrite (sub)grain boundaries formed during annealing. Cr and Mn are strongly concentrated in cementite adjacent to the ferrite/cementite interface due to their lower diffusivities in cementite than in ferrite.

  18. Electrochemical Fabrication and Characterization of Corrosion-Resistant, Ternary, Lead-Based Alloys as a New Material for Steel Surface Protection

    NASA Astrophysics Data System (ADS)

    Aliyev, A. Sh.; Tahirli, H. M.; Elrouby, Mahmoud; Soltanova, N. Sh.; Tagiev, D. B.

    2016-06-01

    This article presents the study of the synthesis of the ternary Pb-Sb-Te alloy on the stainless steel substrate via electrochemical method. The corrosion resistance of the electrodeposited alloy has been investigated via subjecting the electro-synthesized alloy to a corrosive medium containing sulfide ions; this medium is similar to the petroleum refining environment. The resulting film of the electrodeposited alloy was analyzed by the scanning electron microscope, energy-dispersive X-ray analysis, and X-ray diffraction to determine the morphology and the phase structure of the electrodeposited film. It was found that the electrodeposited Pb-Sb-Te alloy thin film is a multiphase composition. The obtained data reveal that the most corrosion-resistant phase is the PbSb2Te4 alloy.

  19. Changes in the Structure and Properties of Welded Joints of Low-Alloy Steels, Subjected to Cyclic Loads

    NASA Astrophysics Data System (ADS)

    Kuskov, V. N.; Kovenskiy, I. M.; Kuskov, K. V.

    2016-04-01

    Time-varying loads negatively affect the properties and structure of materials. Structural failures typically occur at loads below the yield point. In this work, fatigue tests of welded joints of low-alloy steels were carried out in an asymmetric cycle at loads of 60 and 80% of the yield strength. The stress ratio was 0.8-0.9. On the basis of the results of the tests, equations linking the number of cycles to failure with test parameters were obtained. Such equations can be used for estimating the residual life of elements both under construction and in operation. It has been found that the failure is not instantaneous. Specimens of steels continue to resist variable loads for 4000 - 26000 cycles to failure, depending on steel grade and the parameters of the test. Under operating conditions, it gives an opportunity to discover the onset of failure and dispose of the defective part or to replace the entire structure. A standard technique was used to measure the microhardness on the fractured specimens. The distance between the nearest indentations was 0.2 mm. The results of the measurements were plotted in graphs of ahardness change characteristic for all steels under study. A microhardness “step” has been discovered in areas with high dislocation density, as evidenced by x-ray diffraction and transmission electron microscopy. An intermediate stage of the investigation is the development of recommendations for determining the moment of failure of welded constructions with a probability of 95%.

  20. Wetting and Interfacial Characteristics of Mg AZ61 Alloy/Galvanized Steel in Cold Metal Transfer Process

    NASA Astrophysics Data System (ADS)

    Lin, Qiaoli; Yang, Fan; Cao, Rui; Chen, Jianhong; Guo, Tingbiao

    2015-09-01

    The dynamic sessile drop method was used to study the wetting behavior of galvanized steel by molten Mg AZ61 alloy under cold metal transfer condition. The interfacial microstructures were also analyzed by using scanning electron microscope and energy dispersive spectrometry. The observed results showed that the wetting behavior was directly determined by the wire feed speed (or the heat input). The Al-Fe intermetallic layer and Zn-rich zone were observed both at the interface and at the close of triple line. The formations of these interfacial characteristics satisfy the thermodynamic characteristic of Mg-Al/Fe and Mg-Zn/Fe systems.

  1. Effect of Laser Beam Alloying Strategies on the Metallurgical and Mechanical Properties of Hot Forming Tool Steels

    NASA Astrophysics Data System (ADS)

    Hofmann, Konstantin; Neubauer, Franziska; Holzer, Matthias; Mann, Vincent; Hugger, Florian; Roth, Stephan; Schmidt, Michael

    In terms of increasing lightweight designs of car body parts, the machining of high strength steels in hot stamping processes becomes of particular interest. Due to high process forces at hot stamping, the surface of such tools in the area of maximal stress is subject wear, which necessitate some local increase of microhardness to enhance the mechanical performance. Especially laser beam alloying using filler wire and beam oscillation is some suitable method to modify the mechanical properties of tool surfaces to emcompass some continuous martensitic structure, featuring a certain microhardness. Nevertheless the thermal energy input during laser beam alloying induces tempering in the heat affected zone and reduces the hardness. This paper discusses the influence of alloying strategies on the thermal energy input and the resulting metallurgical structure of modified tool surfaces. Also the cooling behavior of alloyed lines for different energy inputs per unit length is of interest. Therefore, the metallurgical microstructure is analyzed regarding microhardness as well as formation of carbides. Furthermore, a numerical thermal simulation is developed to investigate the temperature profile in the heat affected zone of the specimen. These investigations permit the control of the spatiotemporal energy input to avoid tempering of the microstructure.

  2. The effect of alloy elements on the density variation of steel melt at the interdendritic region during solidification

    NASA Astrophysics Data System (ADS)

    Cao, Y. F.; Chen, Y.; Ma, X. P.; Fu, P. X.; Kang, X. H.; Liu, H. W.; Li, D. Z.

    2016-03-01

    Alloying elements in steels have essential effects on the formation of macrosegregation by inducing a density difference between the mushy zone and the bulk melt, and even by the alteration of the solidified microstructure. Hence, in terms of the thermodynamic laws for solidification of an idealized dilute solution, a systematic theoretical analysis on the effect of elements on the density variation of the interdendritic melt is presented for common Fe-based binary alloys. It shows that density variation closely associates with three crucial parameters: the microsegregation parameter λ, the temp-comp-expansion parameter β and the initial composition CL o . With these derived parameters, a simple analytical model is proposed to assess the influence of alloy elements on density change. The theoretical analysis indicates that compared to silicon, the effect of carbon on the density variation cannot be ignored, which is remarkably different from the previous recognition of these two elements. The macrosegregation induced by carbon only is experimentally validated by two dissected 500 kg ingots with different carbon contents. Furthermore, to directly validate the results of theoretical analysis a macrosegregation model with two different microsegregation laws (lever rule and Scheil equation) is established. Then simulations of the convection during solidification in the experimental 500 kg reference ingot are performed for Fe-C and Fe-Si alloys, respectively. It demonstrates that numerically simulated effects of carbon and silicon on the interdendritic convection induced by density inversion are fairly consistent with the analytical predictions.

  3. Manufacture of Alumina-Forming Austenitic Stainless Steel Alloys by Conventional Casting and Hot-Working Methods

    SciTech Connect

    Brady, M.P.; Yamamoto, Y.; Magee, J.H.

    2009-03-23

    Oak Ridge National Laboratory (ORNL) and Carpenter Technology Corporation (CarTech) participated in an in-kind cost share cooperative research and development agreement (CRADA) effort under the auspices of the Energy Efficiency and Renewable Energy (EERE) Technology Maturation program to explore the feasibility for scale up of developmental ORNL alumina-forming austenitic (AFA) stainless steels by conventional casting and rolling techniques. CarTech successfully vacuum melted 30lb heats of four AFA alloy compositions in the range of Fe-(20-25)Ni-(12-14)Cr-(3-4)Al-(1-2.5)Nb wt.% base. Conventional hot/cold rolling was used to produce 0.5-inch thick plate and 0.1-inch thick sheet product. ORNL subsequently successfully rolled the 0.1-inch sheet to 4 mil thick foil. Long-term oxidation studies of the plate form material were initiated at 650, 700, and 800 C in air with 10 volume percent water vapor. Preliminary results indicated that the alloys exhibit comparable (good) oxidation resistance to ORNL laboratory scale AFA alloy arc casting previously evaluated. The sheet and foil material will be used in ongoing evaluation efforts for oxidation and creep resistance under related CRADAs with two gas turbine engine manufacturers. This work will be directed to evaluation of AFA alloys for use in gas turbine recuperators to permit higher-temperature operating conditions for improved efficiencies and reduced environmental emissions.

  4. Crack tip microsampling and growth rate measurements in a 0.021%S low alloy steel in high temperature water

    SciTech Connect

    Young, L.M.; Andresen, P.L.

    1995-12-31

    The concentration of crack tip sulfur species and the corresponding crack growth rates are examined during the environmental assisted cracking of a low alloy steel in high temperature, high purity water. A novel microsampling technique is used to quantify the crack tip chemistry in a growing crack in parallel with measurements of crack growth rate under various environmental conditions. The present study investigates the dissolved crack tip sulfur content of a medium sulfur (0.021wt%) A533B low alloy steel compact tension specimen and the effects of corrosion potential, fatigue loading frequency, bulk sulfate additions, and sampling flow rate. Results are compared with previously published crack tip chemistries collected from a lower sulfur (0.013%) steel in the same environment. Findings indicate that, for both steels, high corrosion potential (oxygenated) conditions correspond with high crack growth rates and high dissolved crack tip sulfur species. In comparison, low corrosion potential produce both low crack growth rates and low dissolved sulfur levels at the crack tip. Both materials exhibit somewhat lower dissolved sulfur levels and lower corresponding crack growth rates when the cyclic loading frequency is decreased from 10{sup {minus}4} to 10{sup {minus}5} Hz, although environmentally enhanced growth rates are still observed. Crack tip microsamples collected during bulk sulfate additions and nitrogen deaerated conditions show higher crack tip concentrations than the simple additive contribution of the prior crack tip sulfur level plus the bulk H{sub 2}SO{sub 4} level. This finding indicates that it is not the potential gradient, per se, which enhances crack tip dissolution, but the aggressive chemistry in the crack.

  5. Nanostructure evolution under irradiation of Fe(C)MnNi model alloys for reactor pressure vessel steels

    NASA Astrophysics Data System (ADS)

    Chiapetto, M.; Becquart, C. S.; Domain, C.; Malerba, L.

    2015-06-01

    Radiation-induced embrittlement of bainitic steels is one of the most important lifetime limiting factors of existing nuclear light water reactor pressure vessels. The primary mechanism of embrittlement is the obstruction of dislocation motion produced by nanometric defect structures that develop in the bulk of the material due to irradiation. The development of models that describe, based on physical mechanisms, the nanostructural changes in these types of materials due to neutron irradiation are expected to help to better understand which features are mainly responsible for embrittlement. The chemical elements that are thought to influence most the response under irradiation of low-Cu RPV steels, especially at high fluence, are Ni and Mn, hence there is an interest in modelling the nanostructure evolution in irradiated FeMnNi alloys. As a first step in this direction, we developed sets of parameters for object kinetic Monte Carlo (OKMC) simulations that allow this to be done, under simplifying assumptions, using a "grey alloy" approach that extends the already existing OKMC model for neutron irradiated Fe-C binary alloys [1]. Our model proved to be able to describe the trend in the buildup of irradiation defect populations at the operational temperature of LWR (∼300 °C), in terms of both density and size distribution of the defect cluster populations, in FeMnNi model alloys as compared to Fe-C. In particular, the reduction of the mobility of point-defect clusters as a consequence of the presence of solutes proves to be key to explain the experimentally observed disappearance of detectable point-defect clusters with increasing solute content.

  6. PCaPAC 2006 Proceedings

    SciTech Connect

    Pavel Chevtsov; Matthew Bickley

    2007-03-30

    The 6-th international PCaPAC (Personal Computers and Particle Accelerator Controls) workshop was held at Jefferson Lab, Newport News, Virginia, from October 24-27, 2006. The main objectives of the conference were to discuss the most important issues of the use of PCs and modern IT technologies for controls of accelerators and to give scientists, engineers, and technicians a forum to exchange the ideas on control problems and their solutions. The workshop consisted of plenary sessions and poster sessions. No parallel sessions were held.Totally, more than seventy oral and poster presentations as well as tutorials were made during the conference, on the basis of which about fifty papers were submitted by the authors and included in this publication. This printed version of the PCaPAC 2006 Proceedings is published at Jefferson Lab according to the decision of the PCaPAC International Program Committee of October 26, 2006.

  7. Shape effect of ultrafine-grained structure on static fracture toughness in low-alloy steel

    PubMed Central

    Inoue, Tadanobu; Kimura, Yuuji; Ochiai, Shojiro

    2012-01-01

    A 0.4C-2Si-1Cr-1Mo steel with an ultrafine elongated grain (UFEG) structure and an ultrafine equiaxed grain (UFG) structure was fabricated by multipass caliber rolling at 773 K and subsequent annealing at 973 K. A static three-point bending test was conducted at ambient temperature and at 77 K. The strength–toughness balance of the developed steels was markedly better than that of conventionally quenched and tempered steel with a martensitic structure. In particular, the static fracture toughness of the UFEG steel, having a yield strength of 1.86 GPa at ambient temperature, was improved by more than 40 times compared with conventional steel having a yield strength of 1.51 GPa. Furthermore, even at 77 K, the fracture toughness of the UFEG steel was about eight times higher than that of the conventional and UFG steels, despite the high strength of the UFEG steel (2.26 GPa). The UFG steel exhibited brittle fracture behavior at 77 K, as did the conventional steel, and no dimple structure was observed on the fracture surface. Therefore, it is difficult to improve the low-temperature toughness of the UFG steel by grain refinement only. The shape of crystal grains plays an important role in delamination toughening, as do their refinement and orientation. PMID:27877493

  8. Shape effect of ultrafine-grained structure on static fracture toughness in low-alloy steel.

    PubMed

    Inoue, Tadanobu; Kimura, Yuuji; Ochiai, Shojiro

    2012-06-01

    A 0.4C-2Si-1Cr-1Mo steel with an ultrafine elongated grain (UFEG) structure and an ultrafine equiaxed grain (UFG) structure was fabricated by multipass caliber rolling at 773 K and subsequent annealing at 973 K. A static three-point bending test was conducted at ambient temperature and at 77 K. The strength-toughness balance of the developed steels was markedly better than that of conventionally quenched and tempered steel with a martensitic structure. In particular, the static fracture toughness of the UFEG steel, having a yield strength of 1.86 GPa at ambient temperature, was improved by more than 40 times compared with conventional steel having a yield strength of 1.51 GPa. Furthermore, even at 77 K, the fracture toughness of the UFEG steel was about eight times higher than that of the conventional and UFG steels, despite the high strength of the UFEG steel (2.26 GPa). The UFG steel exhibited brittle fracture behavior at 77 K, as did the conventional steel, and no dimple structure was observed on the fracture surface. Therefore, it is difficult to improve the low-temperature toughness of the UFG steel by grain refinement only. The shape of crystal grains plays an important role in delamination toughening, as do their refinement and orientation.

  9. Segregation of Alloying Components of Steels R6M5K5 and R6M5K5-MP and its Relation with their Structure and Properties

    NASA Astrophysics Data System (ADS)

    Kremnev, L. S.; Sapronov, I. Yu.

    2014-03-01

    The distribution of alloying components in local regions of the martensitic matrix of high-speed steels R6M5K5 and R6M5K5-MP produced by the conventional process and by the method of powder metallurgy is studied. It is shown that the alloying components are segregated in the martensite, and the segregation is related to the content of retained austenite after hardening and to the microhardness and heat resistance of the steels after final heat treatment.

  10. Simultaneous aluminizing and chromizing of steels to form (Fe,Cr){sub 3}Al coatings and Ge-doped silicide coatings of Cr-Zr base alloys

    SciTech Connect

    Zheng, M.; He, Y.R.; Rapp, R.A.

    1997-12-01

    A halide-activated cementation pack involving elemental Al and Cr powders has been used to achieve surface compositions of approximately Fe{sub 3}Al plus several percent Cr for low alloy steels (T11, T2 and T22) and medium carbon steel (1045 steel). A two-step treatment at 925 C and 1150 C yields the codeposition and diffusion of aluminum and chromium to form dense and uniform ferrite coatings of about 400 {micro}m thickness, while preventing the formation of a blocking chromium carbide at the substrate surfaces. Upon cyclic oxidation in air at 700 C, the coated steel exhibits a negligible 0.085 mg/cm{sup 2} weight gain for 1900 one-hour cycles. Virtually no attack was observed on coated steels tested at ABB in simulated boiler atmospheres at 500 C for 500 hours. But coatings with a surface composition of only 8 wt% Al and 6 wt% Cr suffered some sulfidation attack in simulated boiler atmospheres at temperatures higher than 500 C for 1000 hours. Two developmental Cr-Zr based Laves phase alloys (CN129-2 and CN117(Z)) were silicide/germanide coated. The cross-sections of the Ge-doped silicide coatings closely mimicked the microstructure of the substrate alloys. Cyclic oxidation in air at 1100 C showed that the Ge-doped silicide coating greatly improved the oxidation resistance of the Cr-Zr based alloys.

  11. Dissolution and oxidation behaviour of various austenitic steels and Ni rich alloys in lead-bismuth eutectic at 520 °C

    NASA Astrophysics Data System (ADS)

    Roy, Marion; Martinelli, Laure; Ginestar, Kevin; Favergeon, Jérôme; Moulin, Gérard

    2016-01-01

    Ten austenitic steels and Ni rich alloys were tested in static lead-bismuth eutectic (LBE) at 520 °C in order to obtain a selection of austenitic steels having promising corrosion behaviour in LBE. A test of 1850 h was carried out with a dissolved oxygen concentration between 10-9 and 5 10-4 g kg-1. The combination of thermodynamic of the studied system and literature results leads to the determination of an expression of the dissolved oxygen content in LBE as a function of temperature: RT(K)ln[O](wt%) = -57584/T(K) -55.876T(K) + 254546 (R is the gas constant in J mol-1 K-1). This relation can be considered as a threshold of oxygen content above which only oxidation is observed on the AISI 316L and AISI 304L austenitic alloys in static LBE between 400 °C and 600 °C. The oxygen content during the test leads to both dissolution and oxidation of the samples during the first 190 h and leads to pure oxidation for the rest of the test. Results of mixed oxidation and dissolution test showed that only four types of corrosion behaviour were observed: usual austenitic steels and Ni rich alloys behaviour including the reference alloy 17Cr-12Ni-2.5Mo (AISI 316LN), the 20Cr-31Ni alloy one, the Si containing alloy one and the Al containing alloy one. According to the proposed criteria of oxidation and dissolution kinetics, silicon rich alloys and aluminum rich alloy presented a promising corrosion behaviour.

  12. Investigation of the Phase Formation of AlSi-Coatings for Hot Stamping of Boron Alloyed Steel

    SciTech Connect

    Veit, R.; Kolleck, R.; Hofmann, H.; Sikora, S.

    2011-01-17

    Hot stamping of boron alloyed steel is gaining more and more importance for the production of high strength automotive body parts. Within hot stamping of quenchenable steels the blank is heated up to austenitization temperature, transferred to the tool, formed rapidly and quenched in the cooled tool. To avoid scale formation during the heating process of the blank, the sheet metal can be coated with an aluminium-silicum alloy. The meltimg temperature of this coating is below the austenitization temperature of the base material. This means, that a diffusion process between base material and coating has to take place during heating, leading to a higher melting temperature of the coating.In conventional heating devices, like roller hearth furnaces, the diffusion process is reached by relatively low heating rates. New technologies, like induction heating, reach very high heating rates and offer great potentials for the application in hot stamping. Till now it is not proofed, that this technology can be used with aluminum-silicon coated materials. This paper will present the results of comparative heating tests with a conventional furnace and an induction heating device. For different time/temperature-conditions the phase formation within the coating will be described.

  13. Investigation of the Phase Formation of AlSi-Coatings for Hot Stamping of Boron Alloyed Steel

    NASA Astrophysics Data System (ADS)

    Veit, R.; Hofmann, H.; Kolleck, R.; Sikora, S.

    2011-01-01

    Hot stamping of boron alloyed steel is gaining more and more importance for the production of high strength automotive body parts. Within hot stamping of quenchenable steels the blank is heated up to austenitization temperature, transferred to the tool, formed rapidly and quenched in the cooled tool. To avoid scale formation during the heating process of the blank, the sheet metal can be coated with an aluminium-silicum alloy. The meltimg temperature of this coating is below the austenitization temperature of the base material. This means, that a diffusion process between base material and coating has to take place during heating, leading to a higher melting temperature of the coating. In conventional heating devices, like roller hearth furnaces, the diffusion process is reached by relatively low heating rates. New technologies, like induction heating, reach very high heating rates and offer great potentials for the application in hot stamping. Till now it is not proofed, that this technology can be used with aluminum-silicon coated materials. This paper will present the results of comparative heating tests with a conventional furnace and an induction heating device. For different time/temperature-conditions the phase formation within the coating will be described.

  14. Influence of alloying elements on corrosion resistance of chromium--nickel steels in alkaline medium

    SciTech Connect

    Kanevskii, L.S.; Ebanoidze, D.D.; Kolesnikova, N.N.; Mosolov, A.V.; Shirokova, N.V.; Tovadze, F.N.

    1986-05-01

    The authors study the influence of nickel, chromium, and molybdenum on the behavior of chromium-nickel-molybdenum steels in concentrated alkali and alkali-chlorate solutions, simulating the media in partitioned alkali electrolysis evaporators. Defect-free forgings with no transcrystallization were obtained by pouring the steel into metal molds heated to 1400 degrees C. In the presence of molybdenum the passivation of the steels becomes more difficult, and as a result the corrosion potentials of certain steels in a chlorate-containing solution are much more negative than those of their molybdenum-free analogs.

  15. Evaluation of Protection Schemes for Ultrahigh-Strength Steel Alloys for Landing Gear Applications

    DTIC Science & Technology

    2011-07-01

    coating within landing gear systems. A comparison of various protection schemes (primer and paint only, zinc- nickel , and cadmium) for this new alloy were...corrosion-resistant alloy . The zinc- nickel coating evaluated provides adequate corrosion protection up to 500 hours, but experiences blistering. The prime...components are victims of hydrogen embrittlement, corrosion, and stress corrosion cracking associated with alloys currently in use for landing gear. The

  16. Effect of alloying elements on the composition of carbide phases and mechanical properties of the matrix of high-carbon chromium-vanadium steel

    NASA Astrophysics Data System (ADS)

    Titov, V. I.; Tarasenko, L. V.; Utkina, A. N.

    2017-01-01

    Based on the results of phase physicochemical analysis of high-carbon chromium-vanadium steel, the predominant type of carbide that provides high wear resistance has been established, and its amount and amount of carbon in martensite have been determined. Data on the composition and the amount of carbide phase and on the chemical composition of the martensite of high-carbon steel have been obtained, which allows determination of the alloying-element concentration limits. The mechanical testing of heats of a chosen chemical composition has been carried out after quenching and low-temperature tempering. The tests have demonstrated benefits of new steel in wear resistance and bending strength with the fatigue strength being retained, compared to steels subjected to cementation. The mechanism of secondary strengthening of the steel upon high-temperature tempering has been revealed. High-temperature tempering can be applied to articles that are required to possess both high wear resistance and heat resistance.

  17. Copper-Nickel Cladding on Stainless Steel

    DTIC Science & Technology

    2005-07-01

    steel,. Monel (65Ni/35Cu) alloy consumables should be used as they can tolerate more iron dilution from the steel than the 70-30 copper-nickel alloy ...Cooper Alloys , 400 , K-500 Stainless Steel - Tyles 302, 304, 321, 347 N ickel 200 Silver Braze Alloys Nickel-Chromium Alloy 600 Nickel-Aluminum Bronze 70...cladding of austenitic stainless steels may also offer some ballistic, non-magnetic, and electromagnetic signature advantages over current hull alloys and

  18. Cracking behavior and microstructure of austenitic stainless steels and alloy 690 irradiated in BOR-60 reactor, phase I.

    SciTech Connect

    Chen, Y.; Chopra, O. K.; Soppet, W. K.; Shack, W. J.; Yang, Y.; Allen, T. R.; Univ. of Wisconsin at Madison

    2010-02-16

    Cracking behavior of stainless steels specimens irradiated in the BOR-60 at about 320 C is studied. The primary objective of this research is to improve the mechanistic understanding of irradiation-assisted stress corrosion cracking (IASCC) of core internal components under conditions relevant to pressurized water reactors. The current report covers several baseline tests in air, a comparison study in high-dissolved-oxygen environment, and TEM characterization of irradiation defect structure. Slow strain rate tensile (SSRT) tests were conducted in air and in high-dissolved-oxygen (DO) water with selected 5- and 10-dpa specimens. The results in high-DO water were compared with those from earlier tests with identical materials irradiated in the Halden reactor to a similar dose. The SSRT tests produced similar results among different materials irradiated in the Halden and BOR-60 reactors. However, the post-irradiation strength for the BOR-60 specimens was consistently lower than that of the corresponding Halden specimens. The elongation of the BOR-60 specimens was also greater than that of their Halden specimens. Intergranular cracking in high-DO water was consistent for most of the tested materials in the Halden and BOR-60 irradiations. Nonetheless, the BOR-60 irradiation was somewhat less effective in stimulating IG fracture among the tested materials. Microstructural characterization was also carried out using transmission electron microscopy on selected BOR-60 specimens irradiated to {approx}25 dpa. No voids were observed in irradiated austenitic stainless steels and cast stainless steels, while a few voids were found in base and grain-boundary-engineered Alloy 690. All the irradiated microstructures were dominated by a high density of Frank loops, which varied in mean size and density for different alloys.

  19. Application of LIBS to the in-line process control of liquid high-alloy steel under pressure.

    PubMed

    Hubmer, Gerhard; Kitzberger, Reinhard; Mörwald, Karl

    2006-05-01

    A process optimization and control system called VAI-CON Chem has been developed that uses laser-induced breakdown spectroscopy (LIBS) to quasi-continuously chemically analyze liquid high-alloy steel under pressure. The beam from a Nd:YAG laser, located on safe ground and operating at its fundamental wavelength, is guided by a mirror system to a process tuyere below bath level. Passing through the approximately 1.5 m long tuyere, the beam is then focused onto the steel bath. Light emitted from the induced plasma passes back through the tuyere, which is coupled to a fiber optic cable that carries the information over a distance of approximately 10 m back to an Echelle spectrometer located beside the laser. Calibrations were performed using the complete system, located in a laboratory, during system testing. An induction furnace was used to simulate the AOD converter, wherein the samples were molten and superheated to a temperature of approximately 1600 degrees C and kept at a pressure of approximately 1.7 bar under an argon atmosphere. Twelve different high alloyed reference samples taken from normal AOD production with Fe concentrations of >48 wt.% and non-Fe element concentrations of up to 25 wt.% were available for calibration. The mean residual deviations (defined as the square root of the variance of the concentration ratios determined by LIBS and the reference element concentration ratios) obtained were close to those reported for other comparable high-alloy samples that were investigated at room temperature under normal atmospheric pressure.

  20. A fracture mechanics approach for estimating fatigue crack initiation in carbon and low-alloy steels in LWR coolant environments

    SciTech Connect

    Park, H. B.; Chopra, O. K.

    2000-04-10

    A fracture mechanics approach for elastic-plastic materials has been used to evaluate the effects of light water reactor (LWR) coolant environments on the fatigue lives of carbon and low-alloy steels. The fatigue life of such steel, defined as the number of cycles required to form an engineering-size crack, i.e., 3-mm deep, is considered to be composed of the growth of (a) microstructurally small cracks and (b) mechanically small cracks. The growth of the latter was characterized in terms of {Delta}J and crack growth rate (da/dN) data in air and LWR environments; in water, the growth rates from long crack tests had to be decreased to match the rates from fatigue S-N data. The growth of microstructurally small cracks was expressed by a modified Hobson relationship in air and by a slip dissolution/oxidation model in water. The crack length for transition from a microstructurally small crack to a mechanically small crack was based on studies on small crack growth. The estimated fatigue S-N curves show good agreement with the experimental data for these steels in air and water environments. At low strain amplitudes, the predicted lives in water can be significantly lower than the experimental values.

  1. Development of Novel Pre-alloyed PM Steels for Optimization of Machinability and Fatigue Resistance of PM Components

    NASA Astrophysics Data System (ADS)

    Mardan, Milad; Blais, Carl

    2016-03-01

    It is well known that a large proportion of ferrous PM components require secondary machining operations for dimensional conformance or for producing geometrical features that cannot be generated during die compaction. Nevertheless, the machining behavior of PM parts is generally characterized as being "difficult" due to the presence of residual porosity that lowers thermal conductivity and induces interrupted cutting. Several admixed additives such as MnS and BN-h can be used to improve the machining behavior of PM steels. Nevertheless, their negative effect on mechanical properties, especially fatigue resistance, makes their utilization uninteresting for the fabrication of high-performance PM steel components. This article summarizes the work carried out to develop a novel PM steel that was especially engineered to form machinability enhancing precipitates. This new material is pre-alloyed with tin (Sn) in order to form Cu-Sn (Cu(α)) precipitates during transient liquid phase sintering. The newly developed material presents machinability improvement of 165% compared to reference material used in the PM industry as well as increases in toughness and fatigue resistance of 100% and 13%, respectively.

  2. Effects of Zr, Ti, and Al Additions on Nonmetallic Inclusions and Impact Toughness of Cast Low-Alloy Steel

    NASA Astrophysics Data System (ADS)

    Bizyukov, Pavel V.; Giese, Scott R.

    2017-03-01

    A microalloying of the low-carbon and low-alloy cast steel was conducted with Zr, Ti, and Al that were added to the steel in four combinations. After heat treatment, the samples were tested for impact toughness at room temperature using the Charpy method. The highest values of impact toughness were obtained in the group treated with Zr, while Zr-Ti and Zr-Ti-Al groups showed moderate toughness values; the lowest values were observed in the Zr-Al group. Difference among the treatment groups was observed in the fracture mechanisms, morphology, and area distribution of the inclusions. High toughness values achieved in the trials treated with zirconium corresponded with smooth ductile fracture. The metal treated with a combination of zirconium and titanium had a relatively small area occupied by inclusions, but its toughness was also moderate. Lowest impact toughness values corresponded with the larger area occupied by the inclusions in the trials treated with aluminum. Also, a connection between the solubility product [Al][N] and impact toughness was established. The study also provides a qualitative description and quantitative analysis of the nonmetallic inclusions formation as a result of microalloying treatment. The precipitation sequence of the inclusions was described based on the thermochemical calculations for the nonmetallic compounds discovered in the experimental steel. A description of the size distribution, morphology, and composition was conducted for the oxides, nitrides, sulfides, and multiphase particles.

  3. Nickel-based alloy/austenitic stainless steel dissimilar weld properties prediction on asymmetric distribution of laser energy

    NASA Astrophysics Data System (ADS)

    Zhou, Siyu; Ma, Guangyi; Chai, Dongsheng; Niu, Fangyong; Dong, Jinfei; Wu, Dongjiang; Zou, Helin

    2016-07-01

    A properties prediction method of Nickel-based alloy (C-276)/austenitic stainless steel (304) dissimilar weld was proposed and validated based on the asymmetric distribution of laser energy. Via the dilution level DC-276 (the ratio of the melted C-276 alloy), the relations between the weld properties and the energy offset ratio EC-276 (the ratio of the irradiated energy on the C-276 alloy) were built, and the effects of EC-276 on the microstructure, mechanical properties and corrosion resistance of dissimilar welds were analyzed. The element distribution Cweld and EC-276 accorded with the lever rule due to the strong convention of the molten pool. Based on the lever rule, it could be predicted that the microstructure mostly consists of γ phase in each weld, the δ-ferrite phase formation was inhibited and the intermetallic phase (P, μ) formation was promoted with the increase of EC-276. The ultimate tensile strength σb of the weld joint could be predicted by the monotonically increasing cubic polynomial model stemming from the strengthening of elements Mo and W. The corrosion potential U, corrosion current density I in the active region and EC-276 also met the cubic polynomial equations, and the corrosion resistance of the dissimilar weld was enhanced with the increasing EC-276, mainly because the element Mo could help form a steady passive film which will resist the Cl- ingress.

  4. Metal release from stainless steel powders and massive sheets--comparison and implication for risk assessment of alloys.

    PubMed

    Hedberg, Yolanda; Mazinanian, Neda; Odnevall Wallinder, Inger

    2013-02-01

    Industries that place metal and alloy products on the market are required to demonstrate that they are safe for all intended uses, and that any risks to humans, animals or the environment are adequately controlled. This requires reliable and robust in vitro test procedures. The aim of this study is to compare the release of alloy constituents from stainless steel powders of different grades (focus on AISI 316L) and production routes into synthetic body fluids with the release of the same metals from massive sheets in relation to material and surface characteristics. The comparison is justified by the fact that the difference between massive surfaces and powders from a metal release/dissolution and surface perspective is not clearly elucidated within current legislations. Powders and abraded and aged (24 h) massive sheets were exposed to synthetic solutions of relevance for biological settings and human exposure routes, for periods of up to one week. Concentrations of released iron, chromium, nickel, and manganese in solution were measured, and the effect of solution pH, acidity, complexation capacity, and proteins elucidated in relation to surface oxide composition and its properties. Implications for risk assessments based on in vitro metal release data from alloys are elucidated.

  5. Effect of Alloying Additions on Phase Equilibria and Creep Resistance of Alumina-Forming Austenitic Stainless Steels

    NASA Astrophysics Data System (ADS)

    Yamamoto, Y.; Santella, M. L.; Brady, M. P.; Bei, H.; Maziasz, P. J.

    2009-08-01

    The high-temperature creep properties of a series of alumina-forming austenitic (AFA) stainless steels based on Fe-20Ni-(12-14)Cr-(2.5-4)Al-(0.2-3.3)Nb-0.1C (weight percent) were studied. Computational thermodynamics were used to aid in the interpretation of data on microstructural stability, phase equilibria, and creep resistance. Phases of MC (M: mainly Nb), M23C6 (M: mainly Cr), B2 [ β-(Ni,Fe)Al], and Laves [Fe2(Mo,Nb)] were observed after creep-rupture testing at 750 °C and 170 MPa; this was generally consistent with the thermodynamic calculations. The creep resistance increased with increasing Nb additions up to 1 wt pct in the 2.5 and 3 Al wt pct alloy series, due to the stabilization of nanoscale MC particles relative to M23C6. Additions of Nb greater than 1 wt pct decreased creep resistance in the alloy series due to stabilization of the Laves phase and increased amounts of undissolved, coarse MC, which effectively reduced the precipitation of nanoscale MC particles. The additions of Al also increased the creep resistance moderately due to the increase in the volume fraction of B2 phase precipitates. Calculations suggested that optimum creep resistance would be achieved at approximately 1.5 wt pct Nb in the 4 wt pct Al alloy series.

  6. Effect of alloying additions on phase equilibria and creep resistance of alumina-forming austenitic stainless steels

    SciTech Connect

    Yamamoto, Yukinori; Santella, Michael L; Brady, Michael P; Bei, Hongbin; Maziasz, Philip J

    2009-01-01

    The high-temperature creep properties of a series of alumina-forming austenitic (AFA) stainless steels based on Fe-20Ni-(12-14)Cr-(2.5-4)Al-(0.2-3.3)Nb-0.1C (weight percent) were studied. Computational thermodynamics were used to aid in the interpretation of data on microstructural stability, phase equilibria, and creep resistance. Phases of MC (M: mainly Nb), M{sub 23}C{sub 6} (M: mainly Cr), B2 [{beta}-(Ni,Fe)Al], and Laves [Fe{sub 2}(Mo,Nb)] were observed after creep-rupture testing at 750 C and 170 MPa; this was generally consistent with the thermodynamic calculations. The creep resistance increased with increasing Nb additions up to 1 wt pct in the 2.5 and 3 Al wt pct alloy series, due to the stabilization of nanoscale MC particles relative to M{sub 23}C{sub 6}. Additions of Nb greater than 1 wt pct decreased creep resistance in the alloy series due to stabilization of the Laves phase and increased amounts of undissolved, coarse MC, which effectively reduced the precipitation of nanoscale MC particles. The additions of Al also increased the creep resistance moderately due to the increase in the volume fraction of B2 phase precipitates. Calculations suggested that optimum creep resistance would be achieved at approximately 1.5 wt pct Nb in the 4 wt pct Al alloy series.

  7. Passive behaviour of alloy corrosion-resistant steel Cr10Mo1 in simulating concrete pore solutions with different pH

    NASA Astrophysics Data System (ADS)

    Ai, Zhiyong; Jiang, Jinyang; Sun, Wei; Song, Dan; Ma, Han; Zhang, Jianchun; Wang, Danqian

    2016-12-01

    The passive behaviour of new alloy corrosion-resistant steel Cr10Mo1 and plain carbon steel (as a comparison) in simulating concrete pore solutions of different pH (ranging from 13.5 to 9.0) under open circuit potential conditions, was evaluated by various electrochemical techniques: potentiodynamic polarization, capacitance measurements and electrochemical impedance spectroscopy. The chemical composition and structure of passive films were investigated by X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS). The electrochemical responses of passive films show that Cr10Mo1 steel has an increasing passivity with pH decreasing while carbon steel dose conversely, revealing carbonation does no negative effect on passivation of the corrosion-resistant steel. SIMS reveals that the passive film on the corrosion-resistant steel presents a bilayer structure: an outer layer mainly consisting of Fe oxides and hydroxides, and an inner layer enriched in Cr species, while only a Fe-concentrated layer for carbon steel. According to the XPS analysis results, as the pH decreases, more stable and protective Cr oxides are enriched in the film on Cr10Mo1 steel while Fe oxides gradually decompose. Higher content of Cr oxides in the film layer provides Cr10Mo1 corrosion-resistant steel more excellent passivity at lower pH.

  8. Low Mn alloy steel for cryogenic service and method of preparation

    DOEpatents

    Morris, Jr., John W.; Niikura, Masakazu

    1981-01-01

    A ferritic cryogenic steel which has a relatively low (about 4-6%) manganese content and which has been made suitable for use at cryogenic temperatures by a thermal cycling treatment followed by a final tempering. The steel includes 4-6% manganese, 0.02-0.06% carbon, 0.1-0.4% molybdenum and 0-3% nickel.

  9. 76 FR 78882 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Affirmative Preliminary Determination of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-20

    ...; (c) high nickel steel; (d) ball bearing steel; and (e) concrete reinforcing bars and rods. Also... sulfur, more than 0.04 percent of phosphorus, more than 0.05 percent of selenium, or more than 0.01..., (3) 0.040 percent or less, in the aggregate, of phosphorus and sulfur, (4) 0.006 percent or less...

  10. Precipitation Hardening of Laser-Surfaced Layer of Maraging Alloy at the Surface of Steel 3Kh3M3F

    NASA Astrophysics Data System (ADS)

    Stavrev, D. S.; Shcherbakov, V. S.

    2016-09-01

    The structure and fracture behavior of a layer of maraging alloy deposited by laser surfacing on steel 3Kh3M3F is studied in the initial condition and after precipitation hardening at 550 and 600°C. Microhardness is measured in layer cross sections, and fractures after surfacing and aging are analyzed in an electron microscope.

  11. Creep, creep-rupture tests of Al-surface-alloyed T91 steel in liquid lead bismuth at 500 and 550 °C

    NASA Astrophysics Data System (ADS)

    Weisenburger, A.; Jianu, A.; An, W.; Fetzer, R.; Del Giacco, Mattia; Heinzel, A.; Müller, G.; Markov, V. G.; Kasthanov, A. D.

    2012-12-01

    Surface layers made of FeCrAl alloys on T91 steel have shown their capability as corrosion protection barriers in lead bismuth. Pulsed electron beam treatment improves the density and more over the adherence of such layers. After the treatment of previously deposited coatings a surface graded material is achieved with a metallic bonded interface. Creep-rupture tests of T91 in lead-alloy at 550 °C reveal significant reduced creep strength of non-modified T91 test specimens. Oxide scales protecting the steels from attacks of the liquid metal will crack at a certain strain leading to a direct contact between the steel and the liquid metal. The negative influence of the lead-alloy on the creep behavior of non-modified T91 is stress dependent, but below a threshold stress value of 120 MPa at 550 °C this influence becomes almost negligible. At 500 °C and stress values of 200 MPa and 220 MPa the creep rates are comparable between them and significantly lower than creep rates at 180 MPa of original T91 in air at 550 °C. No signs of LBE influence are detected. The surface modified specimens tested at high stress levels instead had creep-rupture times similar to T91 (original state) tested in air. The thin oxide layers formed on the surface modified steel samples are less susceptible to crack formation and therefore to lead-alloy enhanced creep.

  12. Effects of alloying elements on mechanical and fracture properties of base metals and simulated heat-affected zones of SA 508 steels

    NASA Astrophysics Data System (ADS)

    Kim, Sangho; Lee, Sunghak; Im, Young-Roc; Lee, Hu-Chul; Oh, Yong Jun; Hong, Jun Hwa

    2001-04-01

    This study was aimed at developing low-alloy steels for nuclear reactor pressure vessels by investigating the effects of alloying elements on mechanical and fracture properties of base metals and heat-affected zones (HAZs). Four steels whose compositions were variations of the composition specification for SA 508 steel (class 3) were fabricated by vacuum-induction melting and heat treatment, and their tensile properties and Charpy impact toughness were evaluated. Microstructural analyses indicated that coarse M3C-type carbides and fine M2C-type carbides were precipitated along lath boundaries and inside laths, respectively. In the steels having decreased carbon content and increased molybdenum content, the amount of fine M2C carbides was greatly increased, while that of coarse M3C carbides was decreased, thereby leading to the improvement of tensile properties and impact toughness. Their simulated HAZs also had sufficient impact toughness after postweld heat treatment (PWHT). These findings suggested that the low-alloy steels with high strength and toughness could be processed by decreasing carbon and manganese contents and by increasing molybdenum content.

  13. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  14. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  15. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  16. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  17. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  18. Development of Composite Spectrophotometric Procedures for the Analysis of Low-Alloy Steels and of Aluminum and Its Alloys

    DTIC Science & Technology

    1952-11-01

    alloys, granulated lead was added to separate any copper (iron was simultaneously reduced); complete reduction of the iron was effected by addition of...aliquot of the diluted solution taken for the analysis. Copper in the solution was removed by the addition of granulated lead; the precipitated...lest the reaction become too vigorous and the material froth over. too rarcid effervescence may be moderated by adding a little cold water. 3. Some

  19. Development of Highly Ductile Spheroidized Steel from High C (0.61 wt.% C) Low-Alloy Steel

    NASA Astrophysics Data System (ADS)

    Monia, S.; Varshney, A.; Gouthama; Sangal, S.; Kundu, S.; Samanta, S.; Mondal, K.

    2015-11-01

    This research aims to develop a multiphase steel combining spheroidal cementite and bainite in ductile ferrite matrix possessing an optimal balance of reasonably high strength and excellent ductility. A high carbon (0.61 wt.%) high silicon (1.71 wt.%) EN45 spring steel was annealed to obtain ferrite pearlite microstructure. The samples were given 5 and 10% cold rolling followed by holding at temperature below Ac1 for about 3 h. The samples were then held in intercritical range at 770 °C temperature for different durations ranging from 5 to 20 min for partial re-austenitization followed by quenching in a salt bath maintained at 350 °C and holding for 10 min to get bainite. The samples were finally water quenched. Characterizations of the samples with the help of optical microscopy, x-ray diffraction, scanning electron microscopy, and atomic force microscopy were carried out. Optimal heat-treatment conditions were found out after correlating with tensile properties. The best combination of high tensile strength (~800 MPa) with very high elongation (~29%) was obtained. Effects of cold-rolled strain and holding time in the intercritical region on the mechanical properties and microstructural changes were studied. Finally, structural property correlation is established.

  20. Flight Planning for the International Space Station - Levitation Observation of Dendrite Evolution in Steel Ternary Alloy Rapid Solidification (LODESTARS)

    NASA Technical Reports Server (NTRS)

    Flemings, Merton C.; Matson, Douglas M.; Hyers, Robert W.; Rogers, Jan R.

    2003-01-01

    During rapid solidification, a molten sample is cooled below its equilibrium solidification temperature to form a metastable liquid. Once nucleation is initiated, growth of the solid phase proceeds and can be seen as a sudden rise in temperature. The heat of fusion is rejected ahead of the growing dendrites into the undercooled liquid in a process known as recalescence. Fe-Cr-Ni alloys may form several equilibrium phases and the hypoeutectic alloys, with compositions near the commercially important 316 stainless steel alloy, are observed to solidify by way of a two-step process known as double recalescence. During double recalescence, the first temperature rise is associated with formation of the metastable ferritic solid phase with subsequent conversion to the stable austenitic phase during the second temperature rise. Selection of which phase grows into the undercooled melt during primary solidification may be accomplished by choice of the appropriate nucleation trigger material or by control of the processing parameters during rapid solidification. Due to the highly reactive nature of the molten sample material and in order to avoid contamination of the undercooled melt, a containerless electromagnetic levitation (EML) processing technique is used. In ground-based EML, the same forces that support the weight of the sample against gravity also drive convection in the liquid sample. However, in microgravity, the force required to position the sample is greatly reduced, so convection may be controlled over a wide range of internal flows. Space Shuttle experiments have shown that the double recalescence behavior of Fe-Cr-Ni alloys changes between ground and space EML experiments. This program is aimed at understanding how melt convection influences phase selection and the evolution of rapid solidification microstructures.

  1. Influence of processing parameters and alloying additions on the mechanically determined no-recrystallization temperature in niobium microalloyed steels

    NASA Astrophysics Data System (ADS)

    Homsher-Ritosa, Caryn Nicole

    Microalloying elements are added to plate steels to improve the mechanical properties through grain refinement and precipitation strengthening. In industrial practice, such refinement is obtained by controlling the rolling near critical temperatures in austenite. Generally, a large amount of hot deformation is desired below the no-recrystallization temperature (TNR) to increase the grain boundary area to promote fine ferrite grains upon transformation during cooling. Ideally, a high TNR is desired for increased deformation below TNR at minimal rolling loads and minimal loss of productivity. To increase TNR, microalloying elements such as Nb, V, and Ti are used. The primary purpose of the current study was to determine the effect of multiple microalloying elements on the mechanically determined via torsion testing no-recrystallization temperature (TNR_Tor) in Nb-bearing plate steel. This project focused on the influence of alloying elements and deformation parameters on TNR_Tor. The main objective was to experimentally determine the TNR_Tor for various laboratory-grade steels with systematically varying amounts of Nb, V, and Ti, with C and N held constant. The synergistic effects of these microalloying elements were evaluated. Another objective was to determine the TNR_Tor with systematically varied deformation parameters for the same set of steels. Comparisons of the measured TNR through two different mechanical tests were conducted. Finally, a microstructural evaluation around the mechanically determined TNR_Tor via multistep hot torsion testing was made. To accomplish these objectives six Nb-bearing steels were laboratory produced with 0.065 wt pct C, 0.044 wt pct N, and varying amounts of Nb, V, and Ti. Multistep hot torsion tests were conducted using the GleebleRTM 3500 thermomechanical simulator between the temperatures of 1200 and 750 °C. The mean flow stress was calculated for each deformation step and plotted against the inverse absolute temperature. The

  2. Mechanical Property Data 15-5PH (H1025) Stainless Steel Alloy: Hot-Rolled Plate.

    DTIC Science & Technology

    1984-05-01

    fatigue data of unnotched 15 - 5PH stainless steel (H1025, longitudinal). - ~ ~ 5 l5PH Stumhuts Sisa Pmae. Csinuutae M al 110 -- R*01,Kf-3.0 R.T. 100 1.00...40 - 00 Lsishii. of. cruam Figure 2. Axial load fatigue data of notched 15 -SPH stainless steel (H1025, longitudinal). 3 I 20 15 - 5PH Stainless Stee...600 020 ; I I a -ALI AT 4W4C002 100 TO0 6W 30O 0 4 -5 0 07 Ufetime, Nw Cycles Figure 4. Axial load fatigue data of notched 15 - 5PH stainless steel

  3. Investigation of the Mechanism of Fatigue of Cold-Worked Steel Alloys

    DTIC Science & Technology

    2007-11-02

    treatment are subjected to the fatigue process. Therefore, it is of interest to conduct x-ray investigations of the changes in the crystalline structure of superficially cold-worked steels subjected to alternating loads.

  4. Dynamic strain ageing in prior cold worked 15Cr 15Ni titanium modified stainless steel (Alloy D9)

    NASA Astrophysics Data System (ADS)

    Samuel, K. G.; Ray, S. K.; Sasikala, G.

    2006-09-01

    Dynamic strain ageing (DSA) behavior of a 20% prior cold worked titanium modified austenitic stainless steel (Alloy D9) was investigated in the temperature range 300-1023 K at a constant (nominal) strain rate of 1.33 × 10 -3 s -1. Serrated plastic flow was observed in a narrow temperature region of 773-873 K. Anomalies characteristic of DSA were observed in the variations of strength, ductility, and strain hardening parameters with temperature. Specifically, the difference between ultimate tensile stress and yield stress indicated that a single DSA mechanism is operative over the range of observations. Plastic strain energy density for uniform deformation showed a peak in the DSA temperature range, suggesting that in this material, DSA should enhance the ductile fracture resistance.

  5. Friction Stir Welding of Stainless Steel to Al Alloy: Effect of Thermal Condition on Weld Nugget Microstructure

    NASA Astrophysics Data System (ADS)

    Ghosh, M.; Gupta, R. K.; Husain, M. M.

    2014-02-01

    Joining of dissimilar materials is always a global challenge. Sometimes it is unavoidable to execute multifarious activities by a single component. In the present investigation, 6061 aluminum alloy and 304 stainless steel were joined by friction stir welding (FSW) at different tool rotational rates. Welded joints were characterized in optical and scanning electron microscopes. Reaction products in the stirring zone (SZ) were confirmed through X-ray diffraction. Joint strength was evaluated by tensile testing. It was found that the increment in average heat input and temperature at the weld nugget (WN) facilitated iron enrichment near the interface. Enhancement in the concentration of iron shifted the nature of intermetallics from the Fe2Al5 to Fe-rich end of the Fe-Al binary phase diagram. The peak microhardness and ultimate tensile strength were found to be maxima at the intermediate tool rotational rate, where Fe3Al and FeAl2 appeared along with Fe2Al5.

  6. Boric acid corrosion of carbon and low-alloy steel pressure-boundary components in PWRs: Final report

    SciTech Connect

    O'Neill, A.S.; Hall, J.F.

    1988-08-01

    This report presents the results of a literature survey of the effects of borated water leakage on carbon and low-alloy steel components (other than fasteners) in PWR applications. Boric acid corrosion field experience and laboratory test results are addressed. The report reviews and summarizes corrosion events that have occurred in PWRs and provides, for each event, plant identification, year of occurrence, component or part affected, materials, leak rates (where available), extent of corrosion and repair procedures. Laboratory test data are also discussed, including some recent unpublished data. The report recommends corrective actions that the utilities should take to prevent boric acid corrosion of pressure boundary components. 18 refs., 3 figs., 4 tabs.

  7. Effect of Multistage Heat Treatment on Microstructure and Mechanical Properties of High-Strength Low-Alloy Steel

    NASA Astrophysics Data System (ADS)

    Liu, Qingdong; Wen, Haiming; Zhang, Han; Gu, Jianfeng; Li, Chuanwei; Lavernia, Enrique J.

    2016-05-01

    The influence of Cu-rich precipitates (CRPs) and reverted austenite (RA) on the strength and impact toughness of a Cu-containing 3.5 wt pct Ni high-strength low-alloy (HSLA) steel after various heat treatments involving quenching (Q), lamellarization (L), and tempering (T) is studied using electron back-scatter diffraction, transmission electron microscopy, and atom probe tomography. The QT sample exhibits high strength but low impact toughness, whereas the QL samples mostly possess improved impact toughness but moderate strength, but the QLT samples again have degraded impact toughness due to additional tempering. The dispersion of nanoscale CRPs, which are formed during tempering, is responsible for the enhanced strength but simultaneously leads to the degraded impact toughness. The RA formed during lamellarization contributes to the improved impact toughness. Based on the present study, new heat treatment schedules are proposed to balance strength and impact toughness by optimizing the precipitation of CRPs and RA.

  8. Environmentally assisted cracking of 3.5NiCrMoV low alloy steel under cyclic straining

    SciTech Connect

    Kondo, Yoshiyuki; Bodai, Masaru; Takei, Mao; Sugita, Yuji; Inagaki, Hironobu

    1997-12-01

    Environmentally assisted cracking of 3.5NiCrMoV low alloy steel under cyclic straining was investigated in water environments at 60 C. Effects of strain range, strain rate, strain hold tie and impurities in the water on the crack initiation life were investigated. The effects of long strain hold time up to 100 hours were studied and found to be especially significant. Lower strain rate, longer strain hold time and higher electric conductivity resulted in shorter crack initiation life. The corrosion current from the strained metal was measured in a simulated electrochemical system to clarify the root cause of the life reduction. Test results showed that higher strain range, lower strain rate, longer strain hold time and higher electric conductivity caused increased charge transfer, which caused shorter crack initiation life. A prediction model for the crack initiation life was proposed based on the charge transfer.

  9. Influence of mill scale and rust layer on the corrosion resistance of low-alloy steel in simulated concrete pore solution

    NASA Astrophysics Data System (ADS)

    Shi, Jin-jie; Ming, Jing

    2017-01-01

    Electrochemical impedance spectroscopy, cyclic potentiodynamic polarization measurements, and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy were used to investigate the influence of mill scale and rust layer on the passivation capability and chloride-induced corrosion behaviors of conventional low-carbon (LC) steel and low-alloy (LA) steel in simulated concrete pore solution. The results show that mill scale exerts different influences on the corrosion resistance of both steels at various electrochemical stages. We propose that the high long-term corrosion resistance of LA steel is mainly achieved through the synergistic effect of a gradually formed compact, adherent and well-distributed Cr-enriched inner rust layer and the physical barrier protection effect of mill scale.

  10. Joining of dissimilar AZ31B magnesium alloy and SS400 mild steel by hybrid gas tungsten arc friction stir welding

    NASA Astrophysics Data System (ADS)

    Joo, SungMin

    2013-11-01

    The joining of dissimilar materials, magnesium alloy (AZ31B) and mild steel (SS400), was performed using a hybrid gas tungsten arc-friction stir welding (HGTAFSW) method that applied a preceding gas tungsten arc welding (GTAW) preheating heat source to a mild steel plate surface during friction stir welding (FSW). The mechanical and microstructural characteristics of the HGTAFS welds were evaluated and compared to those of FS welds to confirm the effect of the additional GTAW preheating heat source. The tensile strength of the HGTAFS welds was approximately 91% of that of the magnesium alloy base metal but higher than that of the FS welds. This was attributed to the enhanced material plastic flow and partial annealing effect in the magnesium alloy and mild steel materials by GTAW reheating of the mild steel side, which induced a significant increase in the elongation of the welds. The concentration profiles indicated that no intermetallic FeAl and FeAl3 compounds had formed according to the phase diagram, which led to a decrease in joint strength. Overall, the use of HGTAFSW by applying a GTAW preheating heat source to a mild steelplate surface resulted in a mechanically sounder and metallurgically defect-free welds compared to FSW.

  11. Low-cycle fatigue of Type 347 stainless steel and Hastelloy alloy X in hydrogen gas and in air at elevated temperatures

    NASA Technical Reports Server (NTRS)

    Jaske, C. E.; Rice, R. C.; Buchheit, R. D.; Roach, D. B.; Porfilio, T. L.

    1976-01-01

    An investigation was conducted to assess the low-cycle fatigue resistance of two alloys, Type 347 stainless steel and Hastelloy Alloy X, that were under consideration for use in nuclear-powered rocket vehicles. Constant-amplitude, strain-controlled fatigue tests were conducted under compressive strain cycling at a constant strain rate of 0.001/sec and at total axial strain ranges of 1.5, 3.0, and 5.0 %, in both laboratory-air and low-pressure hydrogen-gas environments at temperatures from 538 to 871 C. Specimens were obtained from three heats of Type 347 stainless steel bar and two heats of Hastelloy Alloy X. The tensile properties of each heat were determined at 21, 538, 649, and 760 C. The continuous cycling fatigue resistance was determined for each heat at temperatures of 538, 760, and 871 C. The Type 347 stainless steel exhibited equal or superior fatigue resistance to the Hastelloy Alloy X at all conditions of this study.

  12. Influence of Minor Alloying Elements on Selective Oxidation and Reactive Wetting of CMnSi TRIP Steel during Hot Dip Galvanizing

    NASA Astrophysics Data System (ADS)

    Cho, Lawrence; Kim, Myung Soo; Kim, Young Ha; De Cooman, Bruno C.

    2014-09-01

    The influence of the addition of minor alloying elements on the selective oxidation and the reactive wetting of CMnSi transformation-induced plasticity (TRIP) steels was studied by means of galvanizing simulator tests. Five TRIP steels containing small alloying additions of Cr, Ni, Ti, Cu, and Sn were investigated. After intercritical annealing (IA) at 1093 K (820 °C) in a N2 + 5 pct H2 gas atmosphere with a dew point of 213 K (-60 °C), two types of oxides were formed on the strip surface: Mn-rich xMnO·SiO2 ( x > 1.5) and Si-rich xMnO·SiO2 ( x < 0.3) oxides. The addition of the minor alloying elements changed the morphology of the Si-rich oxides from a continuous film to discrete islands and this improved the wettability by molten Zn. The improved wetting effect of the minor alloying elements was attributed to an increased area fraction of the surface where the oxides were thinner, enabling a direct unhindered reaction between Fe and the Al in the liquid Zn and the formation of the inhibition layer during the hot dip galvanizing. The addition of a small amount of Sn is shown to significantly decrease the density of Zn-coating defects on CMnSi TRIP steels.

  13. Influence of high-temperature exposure on the microstructure and mechanical properties of dissimilar metal welds between modified 9Cr-1Mo steel and alloy 800

    NASA Astrophysics Data System (ADS)

    Sireesha, M.; Albert, Shaju K.; Sundaresan, S.

    2005-06-01

    Transition joints between ferritic steel and austenitic stainless steel are commonly encountered in high-temperature components of power plants. Service failures in these are known to occur as a result, mainly, of thermal stresses due to expansion coefficient differentials. In order to mitigate the problem, a trimetallic configuration involving an intermediate piece of a material such as Alloy 800 between the ferritic and austenitic steels has been suggested. In our work, modified 9Cr-1Mo steel and 316LN stainless steel are used as the ferritic and austenitic components and the thermal behavior of the joints between modified 9Cr-1Mo steel and Alloy 800 is described in this article. The joints, made using the nickel-base filler material INCONEL 82/182 (INCONEL 82 for the root pass by gas-tungsten arc welding and INCONEL 182 for the filler passes by shielded-metal arc welding), were aged at 625 °C for periods up to 5000 hours. The microstructural changes occurring in the weld metal as well as at the interfaces with the two parent materials are characterized in detail. Results of across-the-weld hardness surveys and cross-weld tension tests and weld metal Charpy impact tests are correlated with the structural changes observed. Principally, the results show that (1) the tendency for carbon to diffuse from the ferritic steel into the weld metal is much less pronounced than when 2.25Cr-1Mo steel is used as the ferritic part; and (2) intermetallic precipitation occurs in the weld metal for aging durations longer than 2000 hours, but the weld metal toughness still remains adequate in terms of the relevant specification.

  14. Kinetics of phosphorus segregation at grain boundaries of low-alloy low-carbon steel

    NASA Astrophysics Data System (ADS)

    Bokshtein, B. S.; Khodan, A. N.; Zabusov, O. O.; Mal'tsev, D. A.; Gurovich, B. A.

    2014-02-01

    In a temperature range of 280-320°C, the mechanism and kinetics of segregation of impurities in steels have yet remained insufficiently studied. Under these conditions diffusion of impurities in the bulk of steel grains practically ceases, and for describing the kinetics of the process it is incorrect to use the Langmuir-McLean equation. In this work we put forward two new approaches to describe the mechanism and kinetics of phosphorus segregation in steels: a model of sequential changes in the state of phosphorus based on first-order reactions and a model of diffusion redistribution of phosphorus between boundaries of carbide precipitates, structure defects, and boundaries of steel grains. A comparative analysis of the suggested models has been conducted, and estimates of the kinetics of segregation based on them have been made; these estimates have been compared with the experimental results obtained in the temperature range of 280-320°C for test times to ˜20 years. It has been shown that these models fairly well describe the experimental kinetics of phosphorus segregation in boundaries of steel grains.

  15. Corrosion of austenitic and martensitic stainless steels in flowing 17Li83Pb alloy

    NASA Astrophysics Data System (ADS)

    Broc, M.; Flament, T.; Fauvet, P.; Sannier, J.

    1988-07-01

    With regard to the behaviour of 316 L stainless steel at 400°C in flowing anisothermal 17Li83Pb the mass transfer suffered by this steel appears to be quite important without noticeable influence of constant or cyclic stress. Evaluation made from solution-annealed specimens leads to a corrosion rate of approximately 30 μm yr -1 at steady state to which a depth of 25 μm has to be added to take into account the initial period phenomena. On the other hand, with semi-stagnant 17Li83Pb at 400° C, the mass transfer of 316 L steel appears to be lower and more acceptable after a 3000-h exposure; but long-time kinetics data have to be achieved in order to see if that better behaviour is persistent and does not correspond to a longer incubation period. As for the martensitic steels their corrosion rate at 450°C in the thermal convection loop TULIP is constant up to 3000 h and five times lower than that observed for 316 L steel in the same conditions.

  16. Effect of cyclic treatment on the formation of a fragmented structure in a sparingly alloyed martensitic steel

    NASA Astrophysics Data System (ADS)

    Tabatchikova, T. I.; Yakovleva, I. L.; Delgado Reina, S. Yu.; Plokhikh, A. I.

    2016-11-01

    Methods of metallography and transmission electron microscopy were used to study the structure of a high-alloy low-carbon steel of martensitic VKS-10 class subjected to cyclic treatment according to different regimes. It has been found that the warm deformation in the α state at 700°C causes the fragmentation of the structure; however, the decomposition of the α solid solution and the precipitation of coarse carbides leads to a significant decrease in the strength. It has been shown that 12 cycles of treatment, including austenitizing at 1000°C, rolling at 700°C, and subsequent γ → α transformation during rapid cooling do not lead to a noticeable fragmentation of the structure. It has been found that the deformation of the overcooled austenite by rolling carried out using 12 cycles in the range of temperatures of 700-500°C and subsequent γ → α transformation lead to the formation of a fragmented structure with a large fraction of fine grains with a size less than 0.5 μm. This treatment and the subsequent tempering at 530°C for 1 h allow us to increase the strength and hardness of the VKS-10 steel at an insignificant decrease in the plasticity.

  17. Wear behavior of the surface alloyed AISI 1020 steel with Fe-Nb-B by TIG welding technique

    SciTech Connect

    Kilinc, B. Durmaz, M.; Abakay, E.; Sen, U.; Sen, S.

    2015-03-30

    Weld overlay coatings also known as hardfacing is a method which involves melting of the alloys and solidification for applied coatings. Recently hardfacing by welding has become a commonly used technique for improvement of material performance in extreme (high temperature, impact/abrasion, erosion, etc.) conditions.In the present study, the coatings were produced from a mixture of ferrous niobium, ferrous boron and iron powders in the ranges of -45µm particle size with different ratio. Fe{sub 12}Nb{sub 5}B{sub 3} and Fe{sub 2}NbBalloys were coated on the AISI 1020 steel surface by TIG welding. The phases formed in the coated layer are Fe{sub 2}B, NbB{sub 2}, NbFeB and Fe0,2 Nb{sub 0,8} phases. The hardness of the presence phases are changing between 1689±85 HV{sub 0.01}, and 181±7 HV{sub 0.1}. Microstructural examinations were realized by optical and scanning electron microscopy. The wear and friction behaviors of Fe{sub 12}Nb{sub 5}B{sub 3} and Fe2NbB realized on the AISI 1020 steel were investigated by the technique of TIG welding by using ball-on-disk arrangement against alumina ball.

  18. Modeling and Simulation of the Impact Response of Maraging Steel Linear Cellular Alloys for Structural Energetic Material Applications

    NASA Astrophysics Data System (ADS)

    Jakus, Adam; Fredenburg, Anthony; McCoy, Tammy; Cochran, Joe; Thadhani, Naresh

    2009-06-01

    A refined Johnson-Cook material strength model is developed for predicting the dynamic strain and fracture response of Maraging 250 steel at high-strain rates. Finite element simulations of rod-on-anvil impacts are carried out at velocities exceeding 100m/s and compared with experimental impact tests performed on a 7.62mm gas gun. The transient and final dimensions of the simulated and experimentally impacted rods are compared and Johnson-Cook strength parameters are modified accordingly. The newly developed Maraging 250 steel Johnson-cook strength model is then applied to simulate the impact response of multiple, 25% dense linear cellular alloys (LCA) of various geometries at velocities exceeding 100m/s. Analyses of the deformation, fragmentation, and stress transfer behavior of the simulated LCAs are performed and validated through comparison of corresponding impact experiments performed on the LCAs produced via an extrusion and reduction process. Stress transfer to the interior walls varies as a function of LCA geometry, which also influences the outward fragmentation and energy retention at the cross-section of impact.

  19. Artificial neural networks and the effects of loading conditions on fatigue life of carbon and low-alloy steels

    SciTech Connect

    Pleune, T.T. |; Chopra, O.K.

    1996-11-01

    The ASME Boiler and Pressure Vessel Code contains rules for the construction of nuclear power plant components. Figure 1-90 of Appendix I to Section III of the Code specifies fatigue design curves for structural materials. However, the effects of light water reactor (LWR) coolant environments are not explicitly addressed by the Code design curves. Recent test data indicate significant decreases in the fatigue lives of carbon and low-alloy steels in LWR environments when five conditions are satisfied simultaneously. When applied strain range, temperature, dissolved oxygen in the water, and sulfur content of the steel are above a minimum threshold level, and the loading strain rate is below a threshold value, environmentally assisted fatigue occurs. For this study, a data base of 1036 fatigue tests was used to train an artificial neural network (ANN). Once the optimal ANN was designed, ANN were trained and used to predict fatigue life for specified sets of loading and environmental conditions. By finding patterns and trends in the data, the ANN can find the fatigue lifetime for any set of conditions. Artificial neural networks show great potential for predicting environmentally assisted corrosion. Their main benefits are that the fit of the data is based purely on data and not on preconceptions and that the network can interpolate effects by learning trends and patterns when data are not available.

  20. Ignition of steel alloys by impact of low-velocity iron/inert particles in gaseous oxygen

    NASA Technical Reports Server (NTRS)

    Benz, Frank J.; Mcilroy, Kenneth; Williams, Ralph E.

    1988-01-01

    The ignition of carbon steel and 316 and 304 stainless steels caused by the impact of low-velocity particles (a standard mixture consisting of 2 g of iron and 3 g of inert materials) in gaseous oxygen was investigated using NASA/White Sands Test Facility for the ignition test, and a subsonic particle impact chamber to accelerate the particles that were injected into flowing oxygen upstream of the target specimen. It was found that the oxygen velocities required to ignite the three alloys were the same as that required to ignite the particle mixture. Ignition occurred at oxygen velocities greater than 45 m/sec at 20 to 24 MPa and was found to be independent of pressure between 2 and 30 MPa. Comparison of the present results and the past results from Wegener (1964) with the Compressed Gas Association (CGA) oxygen velocity limits for safe operations indicates that the CGA limits may be excessively conservative at high pressures and too liberal at low pressures.

  1. Microstructure and Interfacial Reactions During Vacuum Brazing of Stainless Steel to Titanium Using Ag-28 pct Cu Alloy

    NASA Astrophysics Data System (ADS)

    Laik, A.; Shirzadi, A. A.; Sharma, G.; Tewari, R.; Jayakumar, T.; Dey, G. K.

    2015-02-01

    Microstructural evolution and interfacial reactions during vacuum brazing of grade-2 Ti and 304L-type stainless steel (SS) using eutectic alloy Ag-28 wt pct Cu were investigated. A thin Ni-depleted zone of -Fe(Cr, Ni) solid solution formed on the SS-side of the braze zone (BZ). Cu from the braze alloy, in combination with the dissolved Fe and Ti from the base materials, formed a layer of ternary compound , adjacent to Ti in the BZ. In addition, four binary intermetallic compounds, CuTi, CuTi, CuTi and CuTi formed as parallel contiguous layers in the BZ. The unreacted Ag solidified as islands within the layers of CuTi and CuTi. Formation of an amorphous phase at certain locations in the BZ could be revealed. The -Ti(Cu) layer, formed due to diffusion of Cu into Ti-based material, transformed to an -Ti + CuTi eutectoid with lamellar morphology. Tensile test showed that the brazed joints had strength of 112 MPa and failed at the BZ. The possible sequence of events that led to the final microstructure and the mode of failure of these joints were delineated.

  2. International assessment of PCA codes

    SciTech Connect

    Neymotin, L.; Lui, C.; Glynn, J.; Archarya, S.

    1993-11-01

    Over the past three years (1991-1993), an extensive international exercise for intercomparison of a group of six Probabilistic Consequence Assessment (PCA) codes was undertaken. The exercise was jointly sponsored by the Commission of European Communities (CEC) and OECD Nuclear Energy Agency. This exercise was a logical continuation of a similar effort undertaken by OECD/NEA/CSNI in 1979-1981. The PCA codes are currently used by different countries for predicting radiological health and economic consequences of severe accidents at nuclear power plants (and certain types of non-reactor nuclear facilities) resulting in releases of radioactive materials into the atmosphere. The codes participating in the exercise were: ARANO (Finland), CONDOR (UK), COSYMA (CEC), LENA (Sweden), MACCS (USA), and OSCAAR (Japan). In parallel with this inter-code comparison effort, two separate groups performed a similar set of calculations using two of the participating codes, MACCS and COSYMA. Results of the intercode and inter-MACCS comparisons are presented in this paper. The MACCS group included four participants: GREECE: Institute of Nuclear Technology and Radiation Protection, NCSR Demokritos; ITALY: ENEL, ENEA/DISP, and ENEA/NUC-RIN; SPAIN: Universidad Politecnica de Madrid (UPM) and Consejo de Seguridad Nuclear; USA: Brookhaven National Laboratory, US NRC and DOE.

  3. Brazing diamond grits onto a steel substrate using copper alloys as the filler metals

    NASA Astrophysics Data System (ADS)

    Chen, S.-M.; Lin, S.-T.

    1996-12-01

    Surface-set diamond tools were fabricated by an active metal brazing process, using bronze (Cu-8.9Sn) powder and 316L stainless steel powder mixed to various ratios as the braze filler metals. The diamond grits were brazed onto a steel substrate at 1050 °C for 30 min in a dry hydrogen atmosphere. After brazing practice, an intermediate layer rich in chromium formed between the braze filler metal and diamond. A braze filler metal composed of 70 wt % bronze powder and 30 wt % stainless steel powder was found to be optimum in that the diamond grits were strongly impregnated in the filler metal by both mechanical and chemical types of holding. The diamond tools thus fabricated performed better than conventional nickel-plated diamond tools. In service, the braze filler metal wore at almost the same rate as the diamond grits, and no pullout of diamond grits or peeling of the filler metal layer took place.

  4. Cast, heat-resistant austenitic stainless steels having reduced alloying element content

    DOEpatents

    Muralidharan, Govindarajan [Knoxville, TN; Sikka, Vinod Kumar [Oak Ridge, TN; Maziasz, Philip J [Oak Ridge, TN; Pankiw, Roman I [Greensburg, PA

    2010-07-06

    A cast, austenitic steel composed essentially of, expressed in weight percent of the total composition, about 0.4 to about 0.7 C, about 20 to about 30 Cr, about 20 to about 30 Ni, about 0.5 to about 1 Mn, about 0.6 to about 2 Si, about 0.05 to about 1 Nb, about 0.05 to about 1 W, about 0.05 to about 1.0 Mo, balance Fe, the steel being essentially free of Ti and Co, the steel characterized by at least one microstructural component selected from the group consisting of MC, M.sub.23C.sub.6, and M(C, N).

  5. Cast, heat-resistant austenitic stainless steels having reduced alloying element content

    DOEpatents

    Muralidharan, Govindarajan [Knoxville, TN; Sikka, Vinod Kumar [Oak Ridge, TN; Maziasz, Philip J [Oak Ridge, TN; Pankiw, Roman I [Greensburg, PA

    2011-08-23

    A cast, austenitic steel composed essentially of, expressed in weight percent of the total composition, about 0.4 to about 0.7 C, about 20 to about 30 Cr, about 20 to about 30 Ni, about 0.5 to about 1 Mn, about 0.6 to about 2 Si, about 0.05 to about 1 Nb, about 0.05 to about 1 W, about 0.05 to about 1.0 Mo, balance Fe, the steel being essentially free of Ti and Co, the steel characterized by at least one microstructural component selected from the group consisting of MC, M.sub.23C.sub.6, and M(C, N).

  6. Effects of alloying elements on fracture toughness in the transition temperature region of base metals and simulated heat-affected zones of Mn-Mo-Ni low-alloy steels

    NASA Astrophysics Data System (ADS)

    Kim, Sangho; Im, Young-Roc; Lee, Sunghak; Lee, Hu-Chul; Kim, Sung-Joon; Hong, Jun Hwa

    2004-07-01

    This study is concerned with the effects of alloying elements on fracture toughness in the transition temperature region of base metals and heat-affected zones (HAZs) of Mn-Mo-Ni low-alloy steels. Three kinds of steels whose compositions were varied from the composition specification of SA 508 steel (grade 3) were fabricated by vacuum-induction melting and heat treatment, and their fracture toughness was examined using an ASTM E1921 standard test method. In the steels that have decreased C and increased Mo and Ni content, the number of fine M2C carbides was greatly increased and the number of coarse M3C carbides was decreased, thereby leading to the simultaneous improvement of tensile properties and fracture toughness. Brittle martensite-austenite (M-A) constituents were also formed in these steels during cooling, but did not deteriorate fracture toughness because they were decomposed to ferrite and fine carbides after tempering. Their simulated HAZs also had sufficient impact toughness after postweld heat treatment. These findings indicated that the reduction in C content to inhibit the formation of coarse cementite and to improve toughness and the increase in Mo and Ni to prevent the reduction in hardenability and to precipitate fine M2C carbides were useful ways to improve simultaneously the tensile and fracture properties of the HAZs as well as the base metals.

  7. Qualification Data for the Corrosion Behavior of Inconel and Steel Alloys in Nitric Acid

    SciTech Connect

    Mickalonis, J.I.

    2001-04-17

    During filling operations in the Defense Waste Processing Facility (DWPF), melter inserts made of Inconel 690 (I690) have fallen into the canisters which are made of 304L stainless steel (304L). The consequences of possible galvanic corrosion between these materials were evaluated using two electrochemical techniques. Materials for other items which might fall into the canisters were also evaluated including Inconel MA758 (MA758) and A537 carbon steel (A537). The test solutions were concentrated nitric acid, used for validating literature data, and a 10 M nitric acid solution for simulating a possible environment, which may develop due to radiolysis inside the sealed canister.

  8. Qualification Data for the Corrosion Behavior of Inconel and Steel Alloys in Nitric Acid

    SciTech Connect

    Mickalonis, J.I.

    2001-05-02

    During filling operations in the Defense Waste Processing Facility (DWPF), melter inserts made of Inconel 690 (I690) have fallen into the canisters which are made of 304L stainless steel (304L). The consequences of possible galvanic corrosion between these materials were evaluated using two electrochemical techniques. Materials for other items which might fall into the canisters were also evaluated including Inconel MA758 (MA758) and A537 carbon steel (A537). The test solutions were concentrated nitric acid, used for validating literature data, and a 10 M nitric acid solution for simulating a possible environment, which may develop due to radiolysis inside the sealed canister.

  9. Stress corrosion of low alloy steels used in external bolting on pressurised water reactors

    SciTech Connect

    Skeldon, P.; Hurst, P.; Smart, N.R.

    1992-12-31

    The stress corrosion cracking (SCC) susceptibility of AISI 4140 and AISI 4340 steels has been evaluated in five environments, three simulating a leaking aqueous boric acid environment and two simulating ambient external conditions ie moist air and salt spray. Both steels were found to be highly susceptible to SCC in all environments at hardnesses of 400 VPN and above. The susceptibility was greatly reduced at hardnesses below 330 VPN but in one environment, viz refluxing PWR primary water, SCC was observed at hardnesses as low as 260VPN. Threshold stress intensities for SCC were frequently lower than those in the literature.

  10. Effects of silicon and titanium on the corrosion of low-alloy steels in a simulated coal gasification environment at 600 C

    SciTech Connect

    Soler, J.L.J.; Baxter, D.J.; Norton, J.F.

    1999-12-01

    Results of corrosion tests carried out on a series of Fe-12% Cr alloys in coal gasification environments t 600 C were studied. Effects of Si and Ti on corrosion resistance were assessed using data obtained from a commercial 12% Cr alloy, type 410 (UNS S41000), three specially cast model 12% Cr alloys containing 2.7% Si with Ti levels of 0%, 0.4% and 0.7%, respectively, and a higher alloy (type 28 [UNS N08028]) heat exchanger steel. Corrosion tests were carried out using simulated dry-feed entrained slagging gasifier gas The gas (64% carbon monoxide [CO], 3.8% carbon dioxide [CO{sub 2}], 0.8% hydrogen sulfide [H{sub 2}S], and balance H{sub 2} [in vol%]) was premixed and passed over the test pieces at a rate high enough to prevent thermodynamic equilibrium achievement. Results showed that Si had a strongly beneficial influence on corrosion resistance. Ti, depending upon the amount added, exerted a positive or negative influence on corrosion resistance and reduced problems associated with workability. The kinetics of corrosion were presented in terms of weight-change and metal-loss measurements, the synergistic influences of Si and Ti were discussed, and corrosion resistance was compared with that exhibited by a commercial 12% Cr steel and type 28, the higher alloy material.

  11. The effect of potential on the high-temperature fatigue crack growth response of low alloy steels: Part II, electrochemical results

    SciTech Connect

    Moshier, W.C.; James, L.A.

    1997-04-01

    Environmentally assisted cracking (EAC) in low alloy steels was found to be dependent on externally applied potential in low sulfur steels in high temperature water. EAC could be turned on when the specimen was polarized anodically above a critical potential. However, hydrogen (H) additions inhibited the ability of potential to affect EAC. The behavior was related to formation of H ions during H oxidation at the crack mouth. A mechanism based on formation of H sulfide at the crack tip and H ions at the crack mouth is presented to describe the process by which sulfides and H ions affect the critical sulfide concentration at the crack tip.

  12. Monte Carlo simulation of spinodal decomposition in a ternary alloy within a three-phases field: comparison to phase transformation of ferrite in duplex stainless steels

    NASA Astrophysics Data System (ADS)

    Emo, Jonathan; Pareige, Cristelle; Saillet, Sébastien; Domain, Christophe; Pareige, Philippe

    2014-06-01

    This work proposes to model phase transformations occurring in duplex stainless steels using atomistic kinetic Monte Carlo in a ternary model alloy. Kinetics are simulated in the three-phase field of a ternary system. Influence of the precipitation of the third phase on the kinetic of spinodal decomposition between the two other phases is studied in order to understand the synergy between spinodal decomposition and G-phase precipitation which exists in duplex stainless steels. Simulation results are compared to experimental data obtained with atom probe tomography.

  13. Structure Analysis Of Corrosion Resistant Thermal Sprayed Coatings On Low Alloy Steels

    SciTech Connect

    Chaliampalias, D.; Vourlias, G.; Pistofidis, N.; Pavlidou, E.; Stergiou, A.; Stergioudis, G.; Polychroniadis, E. K.

    2007-04-23

    Metallic coatings have been proved to reduce the rate of corrosion of steel in various atmospheres. In this work the structure of Al, Cu-Al and Zn thermal sprayed coatings is examined. The as formed coatings are extremely rough, and they are composed of several phases which increase corrosion resistance as it was determined Salt Spray Chamber tests.

  14. Austenitic stainless steel alloys having improved resistance to fast neutron-induced swelling

    DOEpatents

    Bloom, Everett E.; Stiegler, James O.; Rowcliffe, Arthur F.; Leitnaker, James M.

    1979-01-01

    The present invention is based on the discovery that radiation-induced voids which occur during fast neutron irradiation can be controlled by small but effective additions of titanium and silicon. The void-suppressing effect of these metals in combination is demonstrated and particularly apparent in austenitic stainless steels.

  15. Austenitic stainless steel alloys having improved resistance to fast neutron-induced swelling

    DOEpatents

    Bloom, Everett E.; Stiegler, James O.; Rowcliffe, Arthur F.; Leitnaker, James M.

    1977-03-08

    The present invention is based on the discovery that radiation-induced voids which occur during fast neutron irradiation can be controlled by small but effective additions of titanium and silicon. The void-suppressing effect of these metals in combination is demonstrated and particularly apparent in austenitic stainless steels.

  16. Corrosion behavior of low alloy steels in a wet-dry acid humid environment

    NASA Astrophysics Data System (ADS)

    Zhao, Qing-he; Liu, Wei; Yang, Jian-wei; Zhu, Yi-chun; Zhang, Bin-li; Lu, Min-xu

    2016-09-01

    The corrosion behavior of corrosion resistant steel (CRS) in a simulated wet-dry acid humid environment was investigated and compared with carbon steel (CS) using corrosion loss, polarization curves, X-ray diffraction (XRD), scanning electron microscopy (SEM), electron probe micro-analysis (EPMA), N2 adsorption, and X-ray photoelectron spectroscopy (XPS). The results show that the corrosion kinetics of both steels were closely related to the composition and compactness of the rust, and the electrochemical properties of rusted steel. Small amounts of Cu, Cr, and Ni in CRS increased the amount of amorphous phases and decreased the content of γ-FeOOH in the rust, resulting in higher compactness and electrochemical stability of the CRS rust. The elements Cu, Cr, and Ni were uniformly distributed in the CRS rust and formed CuFeO2, Cu2O, CrOOH, NiFe2O4, and Ni2O3, which enhanced the corrosion resistance of CRS in the wet-dry acid humid environment.

  17. Stress-Corrosion Cracking in High Strength Steels and in Titanium and Aluminum Alloys

    DTIC Science & Technology

    1972-01-01

    importance that the newcomer might wonder why the question is not settled almost as the first order of business . The reason is that to prove the... Agricola and J. T. Snyder, "Stress Corrosion of Explosively Deformed High-Strength Alloys," Metals Eng. Quart. 7 (No. 3), 59 (1967). 138. P. N. Orava

  18. The Corrosion Behavior of Stainless Steels and Copper Alloys Exposed to Natural Seawater

    DTIC Science & Technology

    1991-01-01

    significant changes of the corrosion potential (Ecw) or surface properties. Rotating cylinder experiments indicated that both E., and corrosion rates for...and inorganic chloride corrosion layer that contained alloying elements; a biof ilm; and crystalline, spherical phosphate-rich deposits. All copper...nichtrostendem Stahl und bacteria and diatoms that did not cause significant changes of the Titan entstehenden dfinnen Biofilme bestanden aus

  19. DISTRIBUTION OF ELEMENTS IN THE ALPHA AND GAMMA PHASES OF CHROME-NICKEL STEELS WITH TWO-PHASE STRUCTURE.

    DTIC Science & Technology

    PHASE STUDIES), *NICKEL ALLOYS), (*STEEL, (*CHROMIUM ALLOYS, CZECHOSLOVAKIA, PHASE DIAGRAMS, HEAT OF SOLUTION, SOLID SOLUTIONS, X RAY SPECTROSCOPY, MANGANESE ALLOYS, MOLYBDENUM ALLOYS, AUSTENITE, IRON , CRYSTAL STRUCTURE .

  20. Fabrication of 13Cr-2Mo Ferritic/Martensitic Oxide-Dispersion-Strengthened Steel Components by Mechanical Alloying and Spark-Plasma Sintering

    NASA Astrophysics Data System (ADS)

    Bogachev, I.; Grigoryev, E.; Khasanov, O. L.; Olevsky, E.

    2014-06-01

    The outcomes of the mechanical alloying of 13Cr-2Mo ferritic/martensitic steel and yttria (oxide-dispersion-strengthened steel) powders in a ball mill are reported in terms of the powder particle size and morphology evolution. The optimal ball mill rotation speed and the milling time are discussed. The densification kinetics of the mechanically alloyed powder during the process of spark-plasma sintering is analyzed. An optimal set of the compaction processing parameters, including the maximum temperature, the dwell time, and the heating rate, is determined. The specifics of the densification are discussed in terms of the impact of major spark-plasma sintering parameters as well as the possible phase transformations occurring during compaction processing.

  1. The improvement of cryogenic mechanical properties of Fe-12 Mn and Fe-8 Mn alloy steels through thermal/mechanical treatments

    NASA Technical Reports Server (NTRS)

    Hwang, S. K.; Morris, J. W., Jr.

    1979-01-01

    An investigation has been made to improve the low temperature mechanical properties of Fe-8Mn and Fe-12Mn-0.2 Ti alloy steels. A reversion annealing heat treatment in the two-phase (alpha + gamma) region following cold working has been identified as an effective treatment. In an Fe-12Mn-0.2Ti alloy a promising combination of low temperature (-196 C) fracture toughness and yield strength was obtained by this method. The improvement of properties was attributed to the refinement of grain size and to the introduction of a uniform distribution of retained austenite (gamma). It was also shown that an Fe-8Mn steel could be grain-refined by a purely thermal treatment because of its dislocated alpha-prime martensitic structure and absence of epsilon martensite. As a result, a significant reduction of ductile to brittle transition temperature was obtained.

  2. Application of a Dislocation Density-Based Constitutive Model to Al-Alloyed TWIP Steel

    NASA Astrophysics Data System (ADS)

    Kim, Jinkyung; Estrin, Yuri; De Cooman, Bruno Charles

    2013-09-01

    High Mn steels exhibit an exceptional combination of high strength and large ductility owing to their high strain-hardening rate during deformation. The addition of Al is needed to improve the mechanical performance of TWIP steel by means of the control of the stacking fault energy. In this study, a constitutive modeling approach, which can describe the strain-hardening behavior and the effect of Al on the mechanical properties, was used. In order to understand the deformation behavior of Fe18Mn0.6C and Fe18Mn0.6C1.5Al TWIP steels, a comparative study of the microstructural evolution was conducted by means of transmission electron microscopy and electron backscatter diffraction. The microstructure analysis focused on dislocations, stacking faults, and mechanical twins as these are the defects controlling the strain-hardening behavior of TWIP steels. A comparison of the strain-hardening behavior of Fe18Mn0.6C and Fe18Mn0.6C1.5Al TWIP steels was made in terms of a dislocation density-based constitutive model that goes back to the Kubin-Estrin model. The densities of mobile and forest dislocations are coupled in order to account for the interaction between the two dislocation populations during straining. The model was used to estimate the contribution of dynamic strain aging to the flow stress. As deformation twinning occurred only in a subset of the grains, the grain population was subdivided into twinned grains and twin-free grains. Different constitutive equations were used for the two families of grains. The analysis revealed that (i) the grain size and dynamic recovery effects determine the strain-hardening behavior of the twin-free grains, (ii) the deformation twins, which act as effective barriers to dislocation motion, are the predominant elements of the microstructure that governs the strain hardening of the twinned grains, and (iii) the DSA contribution to strain hardening of TWIP steel is only minor.

  3. Modeling of Austenite Grain Growth During Austenitization in a Low Alloy Steel

    NASA Astrophysics Data System (ADS)

    Dong, Dingqian; Chen, Fei; Cui, Zhenshan

    2016-01-01

    The main purpose of this work is to develop a pragmatic model to predict austenite grain growth in a nuclear reactor pressure vessel steel. Austenite grain growth kinetics has been investigated under different heating conditions, involving heating temperature, holding time, as well as heating rate. Based on the experimental results, the mathematical model was established by regression analysis. The model predictions present a good agreement with the experimental data. Meanwhile, grain boundary precipitates and pinning effects on grain growth were studied by transmission electron microscopy. It is found that with the increasing of the temperature, the second-phase particles tend to be dissolved and the pinning effects become smaller, which results in a rapid growth of certain large grains with favorable orientation. The results from this study provide the basis for the establishment of large-sized ingot heating specification for SA508-III steel.

  4. Possibility of Multi-material Laser Cladding Fabrication of Nickel Alloy and Stainless Steel

    NASA Astrophysics Data System (ADS)

    Kotoban, D.; Aramov, A.; Tarasova, T.

    There are some applications in the industry for multi-material components, including device engineering and multifunctional surface engineering, having to eliminate a brazing or welding technological step. This study investigates the laser cladding process parameters, related single track geometry and quality of multi-material samples. The optimal process parameters for steel were found of 0.21-0.26 J/mm2 and 0.25 10-2 g/mm under the scanning velocity of 1400-1700 mm/min and powder feeding of 4.2-4.5 g/min. The bimetal thin walls, cylinders and cubes were manufactured within the optimal conditions. The requirements of steel and nickel joining were explored. For the examination, the optical microscopy, SEM, EDX microelement analysis and hardness analysis were involved.

  5. 78 FR 78336 - Circular Welded Non-Alloy Steel Pipe From the Republic of Korea: Preliminary Results and Partial...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-26

    ... (HYSCO), Dongbu Steel Co., Ltd., SeAH Steel Corporation, A-JU Besteel Co., Ltd., Kumkang Industrial Co..., A-JU Besteel Co., Ltd., Kumkang Industrial Co., Ltd., Nexteel Co., Ltd., and Union Steel Co.,...

  6. 76 FR 31940 - Circular Welded Non-Alloy Steel Pipe From Taiwan: Notice of Rescission of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-02

    ... following four companies: Far East Machinery Co., Ltd., Kao Hsing Chang Iron & Steel Corp. (also known as Kao Hsiung Chang Iron & Steel Corp.), Yieh Phui Enterprise Co., Ltd., and Chung Hung Steel...

  7. Elucidating the Effect of Alloying Elements on the Behavior of Austenitic Stainless Steels at Elevated Temperatures

    NASA Astrophysics Data System (ADS)

    Naghizadeh, Meysam; Mirzadeh, Hamed

    2016-12-01

    The effect of carbon and molybdenum on elevated temperature behavior of austenitic stainless steels was studied. It was revealed that carbon does not alter the overall grain coarsening behavior but molybdenum significantly retards the growth of grains toward higher temperatures and slower kinetics and effectively increases the grain growth activation energy due to an interaction energy between Mo and grain boundaries. These observations were based on especial activation energy plots, which facilitate the interpretation of results.

  8. Cavitation Erosion of Electro Spark Deposited Nitinol vs. Stellite Alloy on Stainless Steel Substrate

    DTIC Science & Technology

    2015-07-15

    the substrate (Figure 2-2). Rapid solidification produces nano -structures with unique tribological and metallurgical characteristics. When...inventor of electro spark deposition methodology and apparatus. [18] ASAP now terms their process “ nano -fusion” and states that it is generations...stainless might be the root cause of the poor compatibility. ASAP also nano -fused Nitinol onto mild steel coupons, which produced somewhat better results

  9. The influence of cooling rate on the microstructure of stainless steel alloys

    SciTech Connect

    Elmer, J.W.

    1988-09-01

    The emergence of high energy density welding, laser surface modification and rapid solidification as commonly used metallurgical processing techniques has greatly increased the range of cooling rates that can be accessed during the solidification of metals and alloys. The microstructures which develop during these rapid cooling conditions may be significantly different from those which develop during low cooling rate conditions as the result of access to new metastable phases with the additional kinetic limitations that accompany rapid solidification. This investigation explores the influence of cooling rate on a series of seven ternary alloys which span the line of two-fold saturation in the Fe-Ni-Cr system. High speed electron beam surface melting was used to resolidify these alloys at scan speeds up to 5 m/s. The resulting cooling rates were estimated from dendrite arm spacing measurements and were confirmed by heat flow modeling to vary from 7 /times/ 10/sup 0/ /degree/C/s to 8 /times/ 10/sup 6/ /degree/C/s. The microstructures that developed from each solidification condition were examined using optical metallography, electron microprobe analysis, scanning electron microscopy and a vibrating sample magnetometer. These results were used to create diagrams to predict the primary mode of solidification, the ferrite content and the complex microstructural morphologies which develop as a function of interface velocity and composition. 158 refs., 90 figs., 45 tabs.

  10. The Effect of Nb and S Segregation on the Solidification Cracking of Alloy 52M Weld Overlay on CF8 Stainless Steel

    NASA Astrophysics Data System (ADS)

    Chu, H. A.; Young, M. C.; Chu, H. C.; Tsay, L. W.; Chen, C.

    2014-03-01

    The weld overlay of Alloy 52M (a nickel-based filler metal) on a cast 304 (CF8) stainless steel (SS) was made to simulate overlay welding of the safe end of reactor pressure vessels in nuclear power plants. The deteriorated effect of sulfur on solidification cracking of the Alloy 52M overlay was highlighted by using a CF8 substrate with 0.14 wt.% S. Severe solidification cracking was observed when Alloy 52M was directly overlaid on the CF8 substrate. To lower the cracking susceptibility, ER 308L was deposited on the CF8 SS as a buffer layer before the subsequent deposition of Alloy 52M. Under such circumstances, the region near the weld interface between the SS buffer layer and Alloy 52M overlay was susceptible to solidification cracking. The formation of γ-NbC(N), γ-Laves, and γ-(Fe-Ni-S) eutectic-type constituents at the solidification boundaries was responsible for cracking near the weld interface. Nevertheless, depositing two layers of 308L prior to applying Alloy 52M could effectively reduce the cracking susceptibility of the overlay.

  11. Effect of Sintering Atmosphere and Solution Treatment on Density, Microstructure and Tensile Properties of Duplex Stainless Steels Developed from Pre-alloyed Powders

    NASA Astrophysics Data System (ADS)

    Murali, Arun Prasad; Mahendran, Sudhahar; Ramajayam, Mariappan; Ganesan, Dharmalingam; Chinnaraj, Raj Kumar

    2017-01-01

    In this research, Powder Metallurgy (P/M) of Duplex Stainless Steels (DSS) of different compositions were prepared through pre-alloyed powders and elemental powders with and without addition of copper. The powder mix was developed by pot mill for 12 h to obtain the homogeneous mixture of pre-alloyed powder with elemental compositions. Cylindrical green compacts with the dimensions of 30 mm diameter and 12 mm height were compacted through universal testing machine at a pressure level of 560 ± 10 MPa. These green compacts were sintered at 1350 °C for 2 h in hydrogen and argon atmospheres. Some of the sintered stainless steel preforms were solution treated at 1050 °C followed by water quenching. The sintered as well as solution treated samples were analysed by metallography examination, Scanning Electron Microscopy and evaluation of mechanical properties. Ferrite content of sintered and solution treated DSS were measured by Fischer Ferritoscope. It is inferred that the hydrogen sintered DSS depicted better density (94% theoretical density) and tensile strength (695 MPa) than the argon sintered steels. Similarly the microstructure of solution treated DSS revealed existence of more volume of ferrite grains than its sintered condition. Solution treated hydrogen sintered DSS A (50 wt% 316L + 50 wt% 430L) exhibited higher tensile strength of 716 MPa and elongation of 17%, which are 10-13% increment than the sintered stainless steels.

  12. The electroplated Pd-Co alloy film on 316 L stainless steel and the corrosion resistance in boiling acetic acid and formic acid mixture with stirring

    NASA Astrophysics Data System (ADS)

    Li, Sirui; Zuo, Yu; Tang, Yuming; Zhao, Xuhui

    2014-12-01

    Pd-Co alloy films were deposited on 316 L stainless steel by electroplating. Scanning electronic microscopy, X-ray photoelectron spectroscopy, X-ray diffraction, weight loss test and polarization test were used to determine the properties of the Pd-Co alloy films. The Pd-Co films show fine grain size, low porosity and obviously high micro-hardness. The Co content in the film can be controlled in a large range from 21.9 at.% to 57.42 at.%. Pd is rich on the Pd-Co film surface, which is benefit to increase the corrosion resistance. In boiling 90% acetic acid plus 10% formic acid mixture with 0.005 M Br- under stirring, the Pd-Co plated stainless steel samples exhibit evidently better corrosion resistance in contrast to Pd plated samples. The good corrosion resistance of the Pd-Co alloy film is explained by the better compactness, the lower porosity, and the obviously higher micro-hardness of the alloy films, which increases the resistance to erosion and retards the development of micro-pores in the film.

  13. Effects of combined silicon and molybdenum alloying on the size and evolution of microalloy precipitates in HSLA steels containing niobium and titanium

    SciTech Connect

    Pavlina, Erik J.; Van Tyne, C.J.; Speer, J.G.

    2015-04-15

    The effects of combined silicon and molybdenum alloying additions on microalloy precipitate formation in austenite after single- and double-step deformations below the austenite no-recrystallization temperature were examined in high-strength low-alloy (HSLA) steels microalloyed with titanium and niobium. The precipitation sequence in austenite was evaluated following an interrupted thermomechanical processing simulation using transmission electron microscopy. Large (~ 105 nm), cuboidal titanium-rich nitride precipitates showed no evolution in size during reheating and simulated thermomechanical processing. The average size and size distribution of these precipitates were also not affected by the combined silicon and molybdenum additions or by deformation. Relatively fine (< 20 nm), irregular-shaped niobium-rich carbonitride precipitates formed in austenite during isothermal holding at 1173 K. Based upon analysis that incorporated precipitate growth and coarsening models, the combined silicon and molybdenum additions were considered to increase the diffusivity of niobium in austenite by over 30% and result in coarser precipitates at 1173 K compared to the lower alloyed steel. Deformation decreased the size of the niobium-rich carbonitride precipitates that formed in austenite. - Highlights: • We examine combined Si and Mo additions on microalloy precipitation in austenite. • Precipitate size tends to decrease with increasing deformation steps. • Combined Si and Mo alloying additions increase the diffusivity of Nb in austenite.

  14. Orientation dependence of microfracture behavior in a dual-phase high-strength low-alloy steel

    SciTech Connect

    Suh, D.; Lee, S.; Kim, N.J.; Kwon, D.

    1997-02-01

    In selecting the processing conditions and evaluating the reliability of structural materials, microscopic observations and identification of the fracture mechanisms in local cracking behavior are required. An important instance in the failure of the local brittle zone (LBZ) in the welding zone. The LBZ, which is very brittle, is the coarse-grained heat-affected zone near the fusion line, a zone known to be critical to the fracture toughness of welded parts. Thus, maintaining stable fracture resistance by predicting the microfracture behavior is important when using high-strength low-alloy (HSLA) steels in offshore structural steel welds. Depending on the thermal cycles involved during welding, the ferrite/martensite structure can have various morphologies of martensite particles, for example, fibrous and blocky martensite. In summary, in situ SEM fracture tests reveal that in the L-oriented IQ DCB specimen, a microcrack tends to propagate relatively uniformly throughout the ferrite and well-distributed fine fibrous martensite, yielding good elongation with high strength level. Also, the IQ structure in the T orientation shows similar microfracture behavior. On the other hand, in the SQ structure, where blocky-type martensite is mixed with ferrite, strain is localized into shear bands mostly in the ferrite region, and a local microcrack propagates along the strain-localized band formed in the ferrite, resulting in the SQ structure in the T orientation, where the ferrite-martensite bands are parallel to the notch direction, the martensite cannot act as an efficient barrier to microcrack advance, and thus the tensile ductility is decreased.

  15. The Effects of Shot and Laser Peening on Fatigue Life and Crack Growth in 2024 Aluminum Alloy and 4340 Steel

    NASA Technical Reports Server (NTRS)

    Everett, R. A., Jr.; Matthews, W. T.; Prabhakaran, R.; Newman, J. C., Jr.; Dubberly, M. J.

    2001-01-01

    Fatigue and crack growth tests have been conducted on 4340 steel and 2024-T3 aluminum alloy, respectively, to assess the effects of shot peening on fatigue life and the effects of shot and laser peening on crack growth. Two current programs involving fixed and rotary-wing aircraft will not be using shot peened structures. Since the shot peening compressive residual stress depth is usually less than the 0.05-inch initial damage tolerance crack size, it is believed by some that shot peening should have no beneficial effects toward retarding crack growth. In this study cracks were initiated from an electronic-discharged machining flaw which was cycled to produce a fatigue crack of approximately 0.05-inches in length and then the specimens were peened. Test results showed that after peening the crack growth rates were noticeably slower when the cracks were fairly short for both the shot and laser peened specimens resulting in a crack growth life that was a factor of 2 to 4 times greater than the results of the average unpeened test. Once the cracks reached a length of approximately 0.1-inches the growth rates were about the same for the peened and unpeened specimens. Fatigue tests on 4340 steel showed that the endurance limit of a test specimen with a 0.002-inch-deep machining-like scratch was reduced by approximately 40 percent. However, if the "scratched" specimen was shot peened after inserting the scratch, the fatigue life returned to almost 100 percent of the unflawed specimens original fatigue life.

  16. Fast Robust PCA on Graphs

    NASA Astrophysics Data System (ADS)

    Shahid, Nauman; Perraudin, Nathanael; Kalofolias, Vassilis; Puy, Gilles; Vandergheynst, Pierre

    2016-06-01

    Mining useful clusters from high dimensional data has received significant attention of the computer vision and pattern recognition community in the recent years. Linear and non-linear dimensionality reduction has played an important role to overcome the curse of dimensionality. However, often such methods are accompanied with three different problems: high computational complexity (usually associated with the nuclear norm minimization), non-convexity (for matrix factorization methods) and susceptibility to gross corruptions in the data. In this paper we propose a principal component analysis (PCA) based solution that overcomes these three issues and approximates a low-rank recovery method for high dimensional datasets. We target the low-rank recovery by enforcing two types of graph smoothness assumptions, one on the data samples and the other on the features by designing a convex optimization problem. The resulting algorithm is fast, efficient and scalable for huge datasets with O(nlog(n)) computational complexity in the number of data samples. It is also robust to gross corruptions in the dataset as well as to the model parameters. Clustering experiments on 7 benchmark datasets with different types of corruptions and background separation experiments on 3 video datasets show that our proposed model outperforms 10 state-of-the-art dimensionality reduction models. Our theoretical analysis proves that the proposed model is able to recover approximate low-rank representations with a bounded error for clusterable data.

  17. Small punch test evaluation of intergranular embrittlement of an alloy steel

    SciTech Connect

    Baik, J.M.; Buck, O.; Kameda, J.

    1983-12-01

    The ductile-brittle transition temperature in steel is commonly determined using Charpy V-notch impact specimens as specified by ASTM E23-81. In some specific cases, however, the use of this standardized test specimen may be impractical, if not impossible. For instance, it is well known that ferritic steels show a substantial degradation of the mechanical properties after long time exposure to an irradiation environment. Because of the increase in strength and the reduction in ductility due to neutron irradiation, the Charpy V-notch transition temperature is raised causing concern from a safety point of view. To study these radiation effects, a test specimen much smaller than the standard Charpy V-notch specimen would be extremely desirable for two reasons. First, to study neutron damage small specimens take less space within a reactor. Secondly, the damage achieved in simulation experiments, such as proton or electron accelerators, is limited to small penetration depths. Several efforts on the development of such a small test specimen, similar to that used to determine the ductility of sheet metal, as recommended by ASTM E643-78, have been described in the literature. The paper reports on correlations between small punch (SP) and Charpy V-notch (CVN) test results obtained on temper-embrittled NiCr steel. The ductile-brittle transition temperature (DBTT) with intergranular embrittlement being induced by grain boundary segregation of specific impurities was determined. The relation between test results discussed in terms of the micromechanisms of intergranular cracking. It is suggested that in radiation embrittlement investigations similar correlations may be obtained.

  18. Damage and fracture loci for a dual-phase steel and a high-strength low-alloyed steel: Revealing the different plastic localization-damage-ductile fracture pattern

    NASA Astrophysics Data System (ADS)

    Lian, Junhe; Münstermann, Sebastian; Bleck, Wolfgang

    2016-10-01

    The ductile fracture locus has been developed in the recent years as a relevant tool to predict the ductile fracture and assess the structure safety. In the various developed models, the occurrence of the final fracture or the initiation of the fracture is considered as the critical phase of deformation for materials or structures. However, in the application of high-strength steels, the damage onset and evolution are of significant importance in the forming processes, as they are naturally interacting with the plastic localization and ductile fracture and eventually creating various possible failure patterns. The present study contributes to a demonstration of the differences of these features in different steels by quantitatively comparing the material parameters of a hybrid damage mechanics model. A dual-phase steel sheet (DP600) and a high-strength low-alloy steel plate (S355J2+N), which show very different relation patterns between damage and fracture, are investigated. The aim of this study is to compare the plastic localization, damage and fracture loci of them and reveal the differences in their localization-damage initiation-ductile fracture patterns. The reasons for the observed different patterns are discussed and it is concluded that the microstructural features are ultimately contributing to the different patterns and the criteria for evaluating the cold formability of these steels shall be varied depending on their failure patterns.

  19. Laser Metal Deposition as Repair Technology for Stainless Steel and Titanium Alloys

    NASA Astrophysics Data System (ADS)

    Graf, Benjamin; Gumenyuk, Andrey; Rethmeier, Michael

    In a repair process chain, damaged areas or cracks can be removed by milling and subsequently be reconditioned with new material deposition. The use of laser metal deposition has been investigated for this purpose. The material has been deposited into different groove shapes, using both stainless steel and Ti-6Al-4 V. The influence of welding parameters on the microstructure and the heat affected zone has been studied. The parameters have been modified in order to achieve low heat input and consequently low distortion as well as low metallurgical impact. Finally, an evaluation of the opportunities for an automatized repair process is made.

  20. Characterization of the Carbon and Retained Austenite Distributions in Martensitic Medium Carbon, Low Alloy, Steel

    SciTech Connect

    Sherman, D. H.; Cross, Steven M; Kim, Sangho; Grandjean, F.; Long, G. J.; Miller, Michael K

    2007-01-01

    The retained austenite content and carbon distribution in martensite were determined as a function of cooling rate and temper temperature in steel that contained 1.31 at. pct C, 3.2 at. pct Si, and 3.2 at. pct non-iron metallic elements. Mossbauer spectroscopy, transmission electron microscopy (TEM), transmission synchrotron X-ray diffraction (XRD), and atom probe tomography were used for the microstructural analyses. The retained austenite content was an inverse, linear function of cooling rate between 25 and 560 K/s. The elevated Si content of 3.2 at. pct did not shift the start of austenite decomposition to higher tempering temperatures relative to SAE 4130 steel. The minimum tempering temperature for complete austenite decomposition was significantly higher (>650 C) than for SAE 4130 steel ({approx}300 C). The tempering temperatures for the precipitation of transition carbides and cementite were significantly higher (>400 C) than for carbon steels (100 C to 200 C and 200 C to 350 C), respectively. Approximately 90 pct of the carbon atoms were trapped in Cottrell atmospheres in the vicinity of the dislocation cores in dislocation tangles in the martensite matrix after cooling at 560 K/s and aging at 22 C. The 3.2 at. pct Si content increased the upper temperature limit for stable carbon clusters to above 215 C. Significant autotempering occurred during cooling at 25 K/s. The proportion of total carbon that segregated to the interlath austenite films decreased from 34 to 8 pct as the cooling rate increased from 25 to 560 K/s. Developing a model for the transfer of carbon from martensite to austenite during quenching should provide a means for calculating the retained austenite. The maximum carbon content in the austenite films was 6 to 7 at. pct, both in specimens cooled at 560 K/s and at 25 K/s. Approximately 6 to 7 at. pct carbon was sufficient to arrest the transformation of austenite to martensite. The chemical potential of carbon is the same in martensite

  1. Morphology, structure, and chemistry of nanoclusters in a mechanically alloyed nanostructured ferritic steel

    SciTech Connect

    Brandes, M. C.; Kovarik, Libor; Miller, Michael K.; Mills, M. J.

    2012-01-14

    Nanostructured ferritic steels have excellent high temperature creep properties and radiation tolerance due to the presence of a high density of Ti-Y-O-enriched nanoclusters. The morphology of the nanoclusters is found to be consistent with a truncated rhombic dodecahedron defined by the {l_brace}100{r_brace} and {l_brace}110{r_brace} planes in the Fe matrix. The derived symmetry and the compositional information indicate that the nanoclusters are inconsistent with the cubic Y2Ti2O7 or the polymorphs of Y2TiO5 phase. Possible structural models are discussed.

  2. Enhancement of thermal stability of porous bodies comprised of stainless steel or an alloy

    DOEpatents

    Bischoff, Brian L.; Sutton, Theodore G.; Judkins, Roddie R.; Armstrong, Timothy R.; Adcock, Kenneth D.

    2010-11-09

    A method for treating a porous item constructed of metal powder, such as a powder made of Series 400 stainless steel, involves a step of preheating the porous item to a temperature of between about 700 and 900.degree. C. degrees in an oxidizing atmosphere and then sintering the body in an inert or reducing atmosphere at a temperature which is slightly below the melting temperature of the metal which comprises the porous item. The thermal stability of the resulting item is enhanced by this method so that the item retains its porosity and metallic characteristics, such as ductility, at higher (e.g. near-melting) temperatures.

  3. X-ray fluorescence analysis of alloy and stainless steels using a mercuric iodide detector

    NASA Technical Reports Server (NTRS)

    Kelliher, Warren C.; Maddox, W. Gene

    1988-01-01

    A mercuric iodide detector was used for the XRF analysis of a number of NBS standard steels, applying a specially developed correction method for interelemental effects. It is shown that, using this method and a good peak-deconvolution technique, the HgI2 detector is capable of achieving resolutions and count rates needed in the XRF anlysis of multielement samples. The freedom from cryogenic cooling and from power supplies necessary for an electrically cooled device makes this detector a very good candidate for a portable instrument.

  4. Environmental degradation and life time prediction of low alloy steam turbine rotor steels

    SciTech Connect

    Magdowski, R.; Speidel, M.O.

    1995-12-31

    The effect of stress intensity, yield strength and temperature on the growth rates of stress corrosion cracks in 3.5NiCrMoV and other steam turbine rotor steels has been reassessed. It is shown that from 60 C to 170 C the upper limit of laboratory test results in deaerated water coincides with the upper limit of stress corrosion service experience with steam turbine rotors in the field. This permits a conservative estimate of the residual lifetime of cracked components on the basis of laboratory test results.

  5. Improving Hygienic Characteristics of Coated Electrodes for Welding High-Alloy Steels

    NASA Astrophysics Data System (ADS)

    Il'yaschenko, D. P.; Chinakhov, D. A.; Ivanov, K. V.; Sadikov, I. D.

    2017-01-01

    The article presents the results of experimental studies showing that the use of an inverter power supply instead of a diode rectifier provides:: fine-droplet electrode metal transfer which reduces generation time by 46% and transfer time by 28%; transfer of alloying elements from welding materials into the weld metal which reduces its loss from the welding line by 6% and the heat affected area by 3%; reducing the emission rate of welding fumes and their components by 23%; reducing specific emission of welding fumes and their components by 23%.

  6. Effects of proton irradiation on nanocluster precipitation in ferritic steel containing fcc alloying additions

    SciTech Connect

    Zhang, Zhongwu; Liu, C T; Wang, Xun-Li; Miller, Michael K; Ma, Dong; Chen, Guang; Williams, J R; Chin, Bryan

    2012-01-01

    Newly-developed precipitate-strengthened ferritic steels with and without pre-existing nanoscale precipitates were irradiated with 4 MeV protons to a dose of ~5 mdpa at 50 C and subsequently examined by nanoindentation and atom probe tomography (APT). Irradiation-enhanced precipitation and coarsening of pre-existing nanoscale precipitates were observed. Copper partitions to the precipitate core along with a segregation of Ni, Al and Mn to the precipitate/matrix interface after both thermal aging and proton irradiation. Proton irradiation induces the precipitation reaction and coarsening of pre-existing nanoscale precipitates, and these results are similar to a thermal aging process. The precipitation and coarsening of nanoscale precipitates are responsible for the changes in hardness. The observation of the radiation-induced softening is essentially due to the coarsening of the pre-existing Cu-rich nanoscale precipitates. The implication of the precipitation on the embrittlement of reactor-pressure-vessel steels after irradiation is discussed.

  7. Atomistic simulation for deforming complex alloys with application toward TWIP steel and associated physical insights

    NASA Astrophysics Data System (ADS)

    Wang, Peng; Xu, Shaofeng; Liu, Jiabin; Li, Xiaoyan; Wei, Yujie; Wang, Hongtao; Gao, Huajian; Yang, Wei

    2017-01-01

    The interest in promoting deformation twinning for plasticity is mounting for advanced materials. In contrast to disordered grain boundaries, highly organized twin boundaries are beneficial to promoting strength-ductility combination. Twinning deformation typically involves the kinetics of stacking faults, its interplay with dislocations, as well as the interactions between dislocations and twin boundaries. While the latter has been intensively studied, the dynamics of stacking faults has been rarely touched upon. In this work, we report new physical insights on the stacking fault dynamics in twin induced plasticity (TWIP) steels. The atomistic simulation is made possible by a newly introduced approach: meta-atom molecular dynamics simulation. The simulation suggests that the stacking fault interactions are dominated by dislocation reactions that take place spontaneously, different from the existing mechanisms. Whether to generate a single stacking fault, or a twinning partial and a trailing partial dislocation, depends upon a unique parameter, namely the stacking fault energy. The latter in turn determines the deformation twinning characteristics. The complex twin-slip and twin-dislocation interactions demonstrate the dual role of deformation twins as both the dislocation barrier and dislocation storage. This duality contributes to the high strength and high ductility of TWIP steels.

  8. High-temperature Tensile Properties and Creep Life Assessment of 25Cr35NiNb Micro-alloyed Steel

    NASA Astrophysics Data System (ADS)

    Ghatak, Amitava; Robi, P. S.

    2016-05-01

    Reformer tubes in petrochemical industries are exposed to high temperatures and gas pressure for prolonged period. Exposure of these tubes at severe operating conditions results in change in the microstructure and degradation of mechanical properties which may lead to premature failure. The present work highlights the high-temperature tensile properties and remaining creep life prediction using Larson-Miller parametric technique of service exposed 25Cr35NiNb micro-alloyed reformer tube. Young's modulus, yield strength, and ultimate tensile strength of the steel are lower than the virgin material and decreases with the increase in temperature. Ductility continuously increases with the increase in temperature up to 1000 °C. Strain hardening exponent increases up to 600 °C, beyond which it starts decreasing. The tensile properties are discussed with reference to microstructure and fractographs. Based on Larson-Miller technique, a creep life of at least 8.3 years is predicted for the service exposed material at 800 °C and 5 MPa.

  9. Microstructure and Texture Evolution in Cold Rotary Forging of Spur Bevel Gears of 20CrMnTi Alloy Steel

    NASA Astrophysics Data System (ADS)

    Han, Xinghui; Dong, Liying; Hua, Lin; Zhuang, Wuhao

    2016-03-01

    The microstructure of cold rotary forged gears greatly affects their working life. Therefore, the aim of this study is to reveal the evolution of microstructure and texture that occurs during the cold rotary forging of spur bevel gears of 20CrMnTi alloy steel. The evolution of grains of the gear tooth is investigated through optical microscopy. By employing scanning electron microscopy and electron backscatter diffraction, the evolution of the cementite particles and the texture of the gear tooth is also revealed. The results indicate that the grain size distribution is non-uniform from the tooth profile to its center. The cementite particles in the tooth profile are finer and more uniformly distributed than those in the tooth center. After cold rotary forging, the tooth center has a combination of α- and γ-fibers, and the γ-fibers are more developed than the α-fibers, while most of the components in the tooth profile are assembled along the α-fibers.

  10. Effect of Hot Forging on Microstructural Evolution and Impact Toughness in Ultra-high Carbon Low Alloy Steel

    NASA Astrophysics Data System (ADS)

    Kim, J. B.; Kim, J. H.; Kang, C. Y.

    2016-12-01

    The effect of a hot forging ratio on the microstructural variation and tensile properties of ultra-high carbon low alloy steel was investigated. Scanning electron microscopic analyses depict that with an increase in the hot forging ratio, the thickness of the network and acicular proeutectoid cementite decreased. Moreover, the lamella spacing and thickness of the eutectoid cementite decreased and broke up into particle shapes, which then became spheroidized as the hot forging ratio increased. Furthermore, when the forging ratio exceeded 65%, the network and acicular shape of the as-cast state disappeared. By increasing the hot forging ratio, the tensile strength and elongation remained below 50%, but they increased rapidly with an increase in the forging ratio. Strength and elongation were not affected by the thickness of the proeutectoid and eutectoid cementites, but were greatly affected by the shape of the proeutectoid cementite. Due to the decrease in the austenite grain size, as well as the spheroidization of the cementite, the tensile strength and elongation sharply increased.

  11. CRADA NFE-08-01456 Evaluation of Alumina-Forming Austenitic Stainless Steel Alloys in Industrial Gas Turbines

    SciTech Connect

    Brady, Michael P; Pint, Bruce A; Unocic, Kinga A; Yamamoto, Yukinori; Kumar, Deepak; Lipschutz, Mark D.

    2011-09-01

    Oak Ridge National Laboratory (ORNL) and Solar Turbines Incorporated (Solar) participated in an in-kind cost share cooperative research and development agreement (CRADA) effort under the auspices of the Energy Efficiency and Renewable Energy (EERE) Technology Maturation Program to explore the feasibility for use of developmental ORNL alumina-forming austenitic (AFA) stainless steels as a material of construction for industrial gas turbine recuperator components. ORNL manufactured lab scale foil of three different AFA alloy compositions and delivered them to Solar for creep properties evaluation. One AFA composition was selected for a commercial trial foil batch. Both lab scale and the commercial trial scale foils were evaluated for oxidation and creep behavior. The AFA foil exhibited a promising combination of properties and is of interest for future scale up activities for turbine recuperators. Some issues were identified in the processing parameters used for the first trial commercial batch. This understanding will be used to guide process optimization of future AFA foil material production.

  12. Interfacial characterization of SLM parts in multi-material processing: Metallurgical diffusion between 316L stainless steel and C18400 copper alloy

    SciTech Connect

    Liu, Z.H. Zhang, D.Q. Sing, S.L. Chua, C.K. Loh, L.E.

    2014-08-15

    Multi-material processing in selective laser melting using a novel approach, by the separation of two different materials within a single dispensing coating system was investigated. 316L stainless steel and UNS C18400 Cu alloy multi-material samples were produced using selective laser melting and their interfacial characteristics were analyzed using focused ion beam, scanning electron microscopy, energy dispersive spectroscopy and electron back scattered diffraction techniques. A substantial amount of Fe and Cu element diffusion was observed at the bond interface suggesting good metallurgical bonding. Quantitative evidence of good bonding at the interface was also obtained from the tensile tests where the fracture was initiated at the copper region. Nevertheless, the tensile strength of steel/Cu SLM parts was evaluated to be 310 ± 18 MPa and the variation in microhardness values was found to be gradual along the bonding interface from the steel region (256 ± 7 HV{sub 0.1}) to the copper region (72 ± 3 HV{sub 0.1}). - Highlights: • Multi-material processing was successfully implemented and demonstrated in SLM. • Bi-metallic laminates of steel/Cu were successfully produced with the SLM process. • A substantial amount of Fe and Cu diffusion was observed at the bond interface. • Good metallurgical bonding was obtained at the interface of the steel/Cu laminates. • Highly refined microstructure was obtained due to rapid solidification in SLM.

  13. TEM characterization of Au-based alloys to join YSZ to steel for SOFC applications

    SciTech Connect

    Lin, Kun-Lin; Singh, Mrityunjay; Asthana, Rajiv

    2012-01-15

    The microstructures of two gold-based alloys with compositions (in wt.%) of 96.4Au-3Ni-0.6Ti and 97.5Au-0.75Ni-1.75V following oxidation at 850 Degree-Sign C for 200 min were characterized by analytical transmission electron microscopy with energy dispersive spectroscopy and by scanning electron microscopy. In the oxidized 96.4Au-3Ni-0.6Ti interlayer, a dense scale composed of nickel oxide (NiO) and nickel titanate (NiTiO{sub 3}) formed at the alloy surface. No evidence of titanium oxide was found because there was not enough Ti present to form titanium oxide. In the oxidized 97.5Au-0.75Ni-1.75V interlayer, loose vanadium oxide (V{sub 2}O{sub 5}) and nickel vanadate (Ni{sub 2}V{sub 2}O{sub 7}) formed and were distributed within the oxidized 97.5Au-0.75Ni-1.75V interlayer. Similarly, because of the low Ni content in the alloys, no NiO formed. The oxide products in the 96.4Au-3Ni-0.6Ti and 97.5Au-0.75Ni-1.75V interlayers after oxidation are consistent with the Pilling-Bedworth (PB) ratio considerations. - Highlights: Black-Right-Pointing-Pointer Two commercial Au-based reactive metallic interlayers were oxidized at 850 Degree-Sign C for 200 min. Black-Right-Pointing-Pointer The oxidized products at the surface were characterized by TEM/EDS and SEM. Black-Right-Pointing-Pointer NiO and NiTiO{sub 3} formed at the oxidized 96.4Au-3Ni-0.6Ti interlayer. Black-Right-Pointing-Pointer V{sub 2}O{sub 5} and Ni{sub 2}V{sub 2}O{sub 7} were found in the oxidized 97.5Au-0.75Ni-1.75V interlayer. Black-Right-Pointing-Pointer These oxide products are consistent with the Pilling-Bedworth (PB) ratio considerations.

  14. High-Cycle Fatigue of High-Strength Low Alloy Steel Q345 Subjected to Immersion Corrosion for Mining Wheel Applications

    NASA Astrophysics Data System (ADS)

    Dicecco, Sante; Altenhof, William; Hu, Henry; Banting, Richard

    2017-03-01

    In an effort to better understand the impact of material degradation on the fatigue life of mining wheels made of a high-strength low alloy carbon steel (Q345), this study seeks to evaluate the effect of surface corrosion on the high-cycle fatigue behavior of the Q345 alloy. The fatigue behavior of the polished and corroded alloy was investigated. Following exposure to a 3.5 wt.% NaCl saltwater solution, polished and corroded fatigue specimens were tested using an R.R. Moore rotating-bending fatigue apparatus. Microstructural analyses via both optical microscopy and scanning electron microscopy (SEM) revealed that one major phase, α-iron phase, ferrite, and one minor phase, colony pearlite, existed in the extracted Q345 alloy. The results of the fatigue testing showed that the polished and corroded specimens had an endurance strength of approximately 295 and 222 MPa, respectively, at 5,000,000 cycles. The corroded surface condition resulted in a decrease in the fatigue strength of the Q345 alloy by 24.6%. Scanning electron microscope fractography indicated that failure modes for polished and corroded fatigue specimens were consistent in the high-cycle low loading fatigue regime. Conversely, SEM fractography of low-cycle high-loading fatigue specimens found considerable differences in fracture surfaces between the corroded and polished fatigue specimens.

  15. On flux effects in a low alloy steel from a Swedish reactor pressure vessel

    NASA Astrophysics Data System (ADS)

    Boåsen, Magnus; Efsing, Pål; Ehrnstén, Ulla

    2017-02-01

    This study aims to investigate the presence of Unstable Matrix Defects in irradiated pressure vessel steel from weldments of the Swedish PWR Ringhals 4 (R4). Hardness tests have been performed on low flux (surveillance material) and high flux (Halden reactor) irradiated material samples in combination with heat treatments at temperatures of 330, 360 and 390 °C in order to reveal eventual recovery of any hardening features induced by irradiation. The experiments carried out in this study could not reveal any hardness recovery related to Unstable Matrix Defects at relevant temperatures. However, a difference in hardness recovery was found between the low and the high flux samples at heat treatments at higher temperatures than expected for the annihilation of Unstable Matrix Defects-the observed recovery is here attributed to differences of the solute clusters formed by the high and low flux irradiations.

  16. A mechanical property and stress corrosion evaluation of 431 stainless steel alloy

    NASA Technical Reports Server (NTRS)

    Montano, J. W.

    1973-01-01

    The mechanical properties of type 431 stainless steel in two conditions: annealed bar and hardened and tempered bar are presented. Test specimens, manufactured from approximately 1.0 inch (2.54 cm) diameter bar stock, were tested at temperatures of 80 F (+26.7 C), 0 F (-17.8 C), -100 F (-73 C), and -200 F (-129 C). The test data indicated excellent tensile strength, notched/unnotched tensile ratio, ductility, shear, and impact properties at all testing temperatures. Results of the alternate immersion stress corrosion tests on stressed and unstressed longitudinal tensile specimens 0.1250 inch (0.3175 cm) diameter and transverse C-ring specimens, machined from 1.0 inch (2.54 cm) diameter bar stock, indicated that the material is not susceptible to stress corrosion cracking when tested in a 3.5 percent NaCl solution for 180 days.

  17. Nondestructive evaluation of fatigue damage on low-alloy steel by magnetic technique

    SciTech Connect

    Hirasawa, T.; Komura, I.; Chujow, N.

    1994-12-31

    In the nuclear power plant, fatigue damage is one of the most significant degradation behavior which is expected that the structural components is received during long term operation. In order to estimate the plant life and to ensure the reliability of the plants, nondestructive detection and evaluation of fatigue damage of the components are a key technology. Magneto mechanical acoustic emission (MAE) method was applied to the evaluation of fatigue damage of reactor pressure vessel steel. Several MAE parameters which were obtained from the signal processing and waveform analysis on fatigue specimens, were measured and investigated as a function of cumulative fatigue damage factor. Consequently, these MAE parameters were compared to the results by X-ray diffraction technique, hardness testing and microstructural observation. The usefulness of MAE method as the nondestructive evaluation technique of fatigue damage was discussed.

  18. Influence of the thermodynamic parameters on the temper embrittlement of SA508 Gr.4N Ni-Cr-Mo low alloy steel with variation of Ni, Cr and Mn contents

    NASA Astrophysics Data System (ADS)

    Park, Sang-Gyu; Lee, Ki-Hyoung; Min, Ki-Deuk; Kim, Min-Chul; Lee, Bong-Sang

    2012-07-01

    It is well known that SA508 Gr.4N low alloy steel offers improved fracture toughness and strength compared to commercial low alloy steels such as SA508 Gr.3 Mn-Mo-Ni low alloy steel. In this study, the effects of Cr, Mn, and Ni on temper embrittlement in SA508 Gr.4N low alloy steel were evaluated from the viewpoint of thermodynamic parameters such as P diffusivity and C activity. The changes of the ductile-brittle transition temperatures before and after aging were correlated with varying alloying element content, and the diffusivity of P and the activity of C were calculated and correlated with the transition behaviors. The addition of Ni, Cr, and Mn reduce the resistance to temper embrittlement, showing increased Transition-Temperature Shift (TTS) and an increased fraction of intergranular fracture. Although the diffusivity of P is changed by the addition of alloying elements, it does not considerably affect the temper embrittlement. The Mn and Cr content in the matrix significantly reduce the C activity, with showing an inversely proportional relationship to TTS. The change of susceptibility to temper embrittlement caused by Cr and Mn addition could be explained by the variation of C activity. Unlike Cr and Mn, Ni has little effect on the temper embrittlement and C activity.

  19. TEM and HRTEM study of oxide particles in an Al-alloyed high-Cr oxide dispersion strengthened ferritic steel with Hf addition

    NASA Astrophysics Data System (ADS)

    Dou, Peng; Kimura, Akihiko; Kasada, Ryuta; Okuda, Takanari; Inoue, Masaki; Ukai, Shigeharu; Ohnuki, Somei; Fujisawa, Toshiharu; Abe, Fujio; Jiang, Shan; Yang, Zhigang

    2017-03-01

    The nanoparticles in an Al-alloyed high-Cr oxide dispersion strengthened (ODS) ferritic steel with Hf addition, i.e., SOC-16 (Fe-15Cr-2W-0.1Ti-4Al-0.62Hf-0.35Y2O3), have been examined by transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM). Relative to an Al-alloyed high-Cr ODS ferritic steel without Hf addition, i.e., SOC-9 (Fe-15.5Cr-2W-0.1Ti-4Al-0.35Y2O3), the dispersion morphology and coherency of the oxide nanoparticles in SOC-16 were significantly improved. Almost all the small nanoparticles (diameter <10 nm) in SOC-16 were found to be consistent with cubic Y2Hf2O7 oxides with the anion-deficient fluorite structure and coherent with the bcc steel matrix. The larger particles (diameter >10 nm) were also mainly identified as cubic Y2Hf2O7 oxides with the anion-deficient fluorite structure. The results presented here are compared with those of SOC-9 with a brief discussion of the underlying mechanisms of the unusual thermal and irradiation stabilities of the oxides as well as the superior strength, excellent irradiation tolerance and extraordinary corrosion resistance of SOC-16.

  20. Simulation of the elastic deformation of laser-welded joints of an austenitic corrosion-resistant steel and a titanium alloy with an intermediate copper insert

    NASA Astrophysics Data System (ADS)

    Pugacheva, N. B.; Myasnikova, M. V.; Michurov, N. S.

    2016-02-01

    The macro- and microstructures and the distribution of elements and of the values of the microhardness and contact modulus of elasticity along the height and width of the weld metal and heat-affected zone of austenitic corrosion-resistant 12Kh18N10T steel (Russian analog of AISI 321) and titanium alloy VT1-0 (Grade 2) with an intermediate copper insert have been studied after laser welding under different conditions. The structural inhomogeneity of the joint obtained according to one of the regimes selected has been shown: the material of the welded joint represents a supersaturated solid solution of Fe, Ni, Cr, and Ti in the crystal lattice of copper with a uniformly distributed particles of intermetallic compounds Ti(Fe,Cr) and TiCu3. At the boundaries with steel and with the titanium alloy, diffusion zones with thicknesses of 0.1-0.2 mm are formed that represent supersaturated solid solutions based on iron and titanium. The strength of such a joint was 474 MPa, which corresponds to the level of strength of the titanium alloy. A numerical simulation of the mechanical behavior of welded joints upon the elastic tension-compression has been performed taking into account their structural state, which makes it possible to determine the amplitude values of the deformations of the material of the weld.