In Vivo Evaluation of 3D-Printed Polycaprolactone Scaffold Implantation Combined with β-TCP Powder for Alveolar Bone Augmentation in a Beagle Defect Model

PubMed Central

Park, Su A.; Lee, Hyo-Jung; Kim, Keun-Suh; Lee, Jung-Tae; Kim, Sung-Yeol; Chang, Na-Hee

2018-01-01

Insufficient bone volume is one of the major challenges encountered by dentists after dental implant placement. This study aimed to evaluate the efficacy of a customized three-dimensional polycaprolactone (3D PCL) scaffold implant fabricated with a 3D bio-printing system to facilitate rapid alveolar bone regeneration. Saddle-type bone defects were surgically created on the healed site after extracting premolars from the mandibles of four beagle dogs. The defects were radiologically examined using computed tomography for designing a customized 3D PCL scaffold block to fit the defect site. After fabricating 3D PCL scaffolds using rapid prototyping, the scaffolds were implanted into the alveolar bone defects along with β-tricalcium phosphate powder. In vivo analysis showed that the PCL blocks maintained the physical space and bone conductivity around the defects. In addition, no inflammatory infiltrates were observed around the scaffolds. However, new bone formation occurred adjacent to the scaffolds, rather than directly in contact with them. More new bone was observed around PCL blocks with 400/1200 lattices than around blocks with 400/400 lattices, but the difference was not significant. These results indicated the potential of 3D-printed porous PCL scaffolds to promote alveolar bone regeneration for defect healing in dentistry. PMID:29401707

Intra-tumoral delivery of functional ID4 protein via PCL/maltodextrin nano-particle inhibits prostate cancer growth

PubMed Central

Morton, Derrick; Sharma, Pankaj; Gorantla, Yamini; Joshi, Jugal; Nagappan, Perri; Pallaniappan, Ravi; Chaudhary, Jaideep

2016-01-01

ID4, a helix loop helix transcriptional regulator has emerged as a tumor suppressor in prostate cancer. Epigenetic silencing of ID4 promotes prostate cancer whereas ectopic expression in prostate cancer cell lines blocks cancer phenotype. To directly investigate the anti-tumor property, full length human recombinant ID4 encapsulated in biodegradable Polycaprolactone/Maltodextrin (PCL-MD) nano-carrier was delivered to LNCaP cells in which the native ID4 was stably silenced (LNCaP(-)ID4). The cellular uptake of ID4 resulted in increased apoptosis, decreased proliferation and colony formation. Intratumoral delivery of PCL-MD ID4 into growing LNCaP(-)ID4 tumors in SCID mice significantly reduced the tumor volume compared to the tumors treated with chemotherapeutic Docetaxel. The study supports the feasibility of using nano-carrier encapsulated ID4 protein as a therapeutic. Mechanistically, ID4 may assimilate multiple regulatory pathways for example epigenetic re-programming, integration of multiple AR co-regulators or signaling pathways resulting in tumor suppressor activity of ID4. PMID:27487149

Application of molecular dynamics simulation to predict the compatability between water-insoluble drugs and self-associating poly(ethylene oxide)-b-poly(epsilon-caprolactone) block copolymers.

PubMed

Patel, Sarthak; Lavasanifar, Afsaneh; Choi, Phillip

2008-11-01

In the present work, molecular dynamics (MD) simulation was applied to study the solubility of two water-insoluble drugs, fenofibrate and nimodipine, in a series of micelle-forming PEO-b-PCL block copolymers with combinations of blocks having different molecular weights. The solubility predictions based on the MD results were then compared with those obtained from solubility experiments and by the commonly used group contribution method (GCM). The results showed that Flory-Huggins interaction parameters computed by the MD simulations are consistent with the solubility data of the drug/PEO-b-PCL systems, whereas those calculated by the GCM significantly deviate from the experimental observation. We have also accounted for the possibility of drug solubilization in the PEO block of PEO-b-PCL.

Synthesizing a Trefoil Knotted Block Copolymer via Ring-Expansion Strategy

DOE PAGES

Cao, Pengfei; Rong, Li-Han; Mangadlao, Joey; ...

2017-02-07

We synthesized a synthetic trefoil knotted poly(e-caprolatone) block-poly(L-lactide) (TK-PLA-b-PCL) via a ring expansion strategy from a trefoil knotted tin (Sn) initiator. Ring closing reaction between the bis-copper(I) templated phenanthro line complex and dibutyldimethoxytin results in a templated trefoil knotted initiator. Furthermore, the bis-copper(I) templated trefoil knotted poly(L-lactide) (TK-PLA) can be synthesized by ring-opening polymerization of L-lactide monomer, and decomplexation reaction of the templated TK-PLA will result in a geniune TK-PLA without constraint from the copper template. Subsequent insertion of e caprolactone in the bis-copper(I) templated TK-PLA forms the templated trefoil knotted block copolymer, i.e., TK-PLA-b-PCL, and the copper-free TK-PLA-b-PCL canmore » be obtained by decomplexation reaction. Finally, both TK-PLA and TK-PLA-b-PCL are analyzed by the 1 H NMR, FT-IR, UV-vis, DLS, and GPC.« less

Selective Cell Adhesion and Biosensing Applications of Bio-Active Block Copolymers Prepared by CuAAC/Thiol-ene Double Click Reactions.

PubMed

Oyman Eyrilmez, Gizem; Doran, Sean; Murtezi, Eljesa; Demir, Bilal; Odaci Demirkol, Dilek; Coskunol, Hakan; Timur, Suna; Yagci, Yusuf

2015-09-01

N-Acetyl-l-cysteine (NAC)-capped poly(methyl methacrylate)-b-polycaprolactone block copolymer (PMMA-b-PCL-NAC) was prepared using the previously described one-pot photoinduced sequential CuAAC/thiol-ene double click procedure. PMMA-b-PCL-NAC had previously shown good applicability as a matrix for cell adhesion of cells from the Vero cell line (African green monkey kidney epithelial). Here, in this work, PMMA-b-PCL-NAC served as an excellent immobilization matrix for biomolecule conjugation. Covalent binding of RGD (R: arginine, G: glycine, and D: aspartic acid) peptide sequence onto the PMMA-b-PCL-NAC-coated surface was performed via EDC chemistry. RGD-modified PMMA-b-PCL-NAC (PMMA-b-PCL-NAC-RGD) as a non-toxic cell proliferation platform was used for selective "integrin αvβ3-mediated cell adhesion and biosensing studies. Both optical and electrochemical techniques were used to monitor the adhesion differences between "integrin αvβ3" receptor positive and negative cell lines on to the designed biofunctional surfaces. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Toxicity evaluation of methoxy poly(ethylene oxide)-block-poly(ε-caprolactone) polymeric micelles following multiple oral and intraperitoneal administration to rats.

PubMed

Binkhathlan, Ziyad; Qamar, Wajhul; Ali, Raisuddin; Kfoury, Hala; Alghonaim, Mohammed

2017-09-01

Methoxy poly(ethylene oxide)- block -poly(ɛ-caprolactone) (PEO- b -PCL) copolymers are amphiphilic and biodegradable copolymers designed to deliver a variety of drugs and diagnostic agents. The aim of this study was to synthesize PEO- b -PCL block copolymers and assess the toxic effects of drug-free PEO- b -PCL micelles after multiple-dose administrations via oral or intraperitoneal (ip) administration in rats. Assembly of block copolymers was achieved by co-solvent evaporation method. To investigate the toxicity profile of PEO- b -PCL micelles, sixty animals were divided into two major groups: The first group received PEO- b -PCL micelles (100 mg/kg) by oral gavage daily for seven days, while the other group received the same dose of micelles by ip injections daily for seven days. Twenty-four hours following the last dose, half of the animals from each group were sacrificed and blood and organs (lung, liver, kidneys, heart and spleen) were collected. Remaining animals were observed for further 14 days and was sacrificed at the end of the third week, and blood and organs were collected. None of the polymeric micelles administered caused any significant effects on relative organ weight, animal body weight, leucocytes count, % lymphocytes, liver and kidney toxicity markers and organs histology. Although the dose of copolymers used in this study is much higher than those used for drug delivery, it did not cause any significant toxic effects in rats. Histological examination of all the organs confirmed the nontoxic nature of the micelles.

Regulating the surface poly(ethylene glycol) density of polymeric nanoparticles and evaluating its role in drug delivery in vivo.

PubMed

Du, Xiao-Jiao; Wang, Ji-Long; Liu, Wei-Wei; Yang, Jin-Xian; Sun, Chun-Yang; Sun, Rong; Li, Hong-Jun; Shen, Song; Luo, Ying-Li; Ye, Xiao-Dong; Zhu, Yan-Hua; Yang, Xian-Zhu; Wang, Jun

2015-11-01

Poly(ethylene glycol) (PEG) is usually used to protect nanoparticles from rapid clearance in blood. The effects are highly dependent on the surface PEG density of nanoparticles. However, there lacks a detailed and informative study in PEG density and in vivo drug delivery due to the critical techniques to precisely control the surface PEG density when maintaining other nano-properties. Here, we regulated the polymeric nanoparticles' size and surface PEG density by incorporating poly(ε-caprolactone) (PCL) homopolymer into poly(ethylene glycol)-block-poly(ε-caprolactone) (PEG-PCL) and adjusting the mass ratio of PCL to PEG-PCL during the nanoparticles preparation. We further developed a library of polymeric nanoparticles with different but controllable sizes and surface PEG densities by changing the molecular weight of the PCL block in PEG-PCL and tuning the molar ratio of repeating units of PCL (CL) to that of PEG (EG). We thus obtained a group of nanoparticles with variable surface PEG densities but with other nano-properties identical, and investigated the effects of surface PEG densities on the biological behaviors of nanoparticles in mice. We found that, high surface PEG density made the nanoparticles resistant to absorption of serum protein and uptake by macrophages, leading to a greater accumulation of nanoparticles in tumor tissue, which recuperated the defects of decreased internalization by tumor cells, resulting in superior antitumor efficacy when carrying docetaxel. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization of multiblock copolymers by chromatographic techniques.

PubMed

N'Goma, Patrick Yoba; Radke, Wolfgang; Malz, Frank; Ziegler, Hans Jörg; Zierke, Michael; Behl, Marc; Lendlein, Andreas

2011-02-01

Multiblock copolymers (MBC) composed of blocks of poly(1,4-dioxanone) (PPDO) and poly(e-caprolactone) (PCL) were investigated in order to gain information on the extend of chemical heterogeneity of the samples. A gradient chromatographic method was established allowing separation of purely PPDO- from purely PCL-containing chains. Application of the gradient to MBC made of PPDO- and PCL-diols connected by trimethylhexamethylene diisocyanate (TMDI) resulted in two well separated peaks which were analyzed by means of FTIR, 1H-NMR and pyrolysis GC-MS. It was shown that the first peak was composed to a large extent of PPDO and only lower amounts of PCL were incorporated. Conversely, the second peak consisted predominantly of PCL with only a minor fraction of PPDO. Thus, the MBCs having PPDO and PCL segments show an unexpected broad chemical heterogeneity.

Aqueous self-assembly of poly(ethylene oxide)-block-poly(ε-caprolactone) (PEO-b-PCL) copolymers: disparate diblock copolymer compositions give rise to nano- and meso-scale bilayered vesicles

NASA Astrophysics Data System (ADS)

Qi, Wei; Ghoroghchian, P. Peter; Li, Guizhi; Hammer, Daniel A.; Therien, Michael J.

2013-10-01

Nanoparticles formed from diblock copolymers of FDA approved PEO and PCL have generated considerable interest as in vivo drug delivery vehicles. Herein, we report the synthesis of the most extensive family PEO-b-PCL copolymers that vary over the largest range of number-average molecular weights (Mn: 3.6-57k), PEO weight fractions (fPEO: 0.08-0.33), and PEO chain lengths (0.75-5.8k) reported to date. These polymers were synthesized in order to establish the full range of aqueous phase behaviours of these diblock copolymers and to specifically identify formulations that were able to generate bilayered vesicles (polymersomes). Cryogenic transmission electron microscopy (cryo-TEM) was utilized in order to visualize the morphology of these structures upon aqueous self-assembly of dry polymer films. Nanoscale polymersomes were formed from PEO-b-PCL copolymers over a wide range of PEO weight fractions (fPEO: 0.14-0.27) and PEO molecular weights (0.75-3.8k) after extrusion of aqueous suspensions. Comparative morphology diagrams, which describe the nature of self-assembled structures as a function of diblock copolymer molecular weight and PEO weight fraction, show that in contrast to micron-scale polymersomes, which form only from a limited range of PEO-b-PCL diblock copolymer compositions, a multiplicity of PEO-b-PCL diblock copolymer compositions are able to give rise to nanoscale vesicles. These data underscore that PEO-b-PCL compositions that spontaneously form micron-sized polymersomes, as well as those that have previously been reported to form polymersomes via a cosolvent fabrication system, provide only limited insights into the distribution of PEO-b-PCL diblocks that give rise to nanoscale vesicles. The broad range of polymersome-forming PEO-b-PCL compositions described herein suggest the ability to construct extensive families of nanoscale vesicles of varied bilayer thickness, providing the ability to tune the timescales of vesicle degradation and encapsulant release based on the intended in vivo application.Nanoparticles formed from diblock copolymers of FDA approved PEO and PCL have generated considerable interest as in vivo drug delivery vehicles. Herein, we report the synthesis of the most extensive family PEO-b-PCL copolymers that vary over the largest range of number-average molecular weights (Mn: 3.6-57k), PEO weight fractions (fPEO: 0.08-0.33), and PEO chain lengths (0.75-5.8k) reported to date. These polymers were synthesized in order to establish the full range of aqueous phase behaviours of these diblock copolymers and to specifically identify formulations that were able to generate bilayered vesicles (polymersomes). Cryogenic transmission electron microscopy (cryo-TEM) was utilized in order to visualize the morphology of these structures upon aqueous self-assembly of dry polymer films. Nanoscale polymersomes were formed from PEO-b-PCL copolymers over a wide range of PEO weight fractions (fPEO: 0.14-0.27) and PEO molecular weights (0.75-3.8k) after extrusion of aqueous suspensions. Comparative morphology diagrams, which describe the nature of self-assembled structures as a function of diblock copolymer molecular weight and PEO weight fraction, show that in contrast to micron-scale polymersomes, which form only from a limited range of PEO-b-PCL diblock copolymer compositions, a multiplicity of PEO-b-PCL diblock copolymer compositions are able to give rise to nanoscale vesicles. These data underscore that PEO-b-PCL compositions that spontaneously form micron-sized polymersomes, as well as those that have previously been reported to form polymersomes via a cosolvent fabrication system, provide only limited insights into the distribution of PEO-b-PCL diblocks that give rise to nanoscale vesicles. The broad range of polymersome-forming PEO-b-PCL compositions described herein suggest the ability to construct extensive families of nanoscale vesicles of varied bilayer thickness, providing the ability to tune the timescales of vesicle degradation and encapsulant release based on the intended in vivo application. Electronic supplementary information (ESI) available: Materials and methods, characterization data. See DOI: 10.1039/c3nr03250g

Tunable Surface Repellency Maintains Stemness and Redox Capacity of Human Mesenchymal Stem Cells.

PubMed

Balikov, Daniel A; Crowder, Spencer W; Boire, Timothy C; Lee, Jung Bok; Gupta, Mukesh K; Fenix, Aidan M; Lewis, Holley N; Ambrose, Caitlyn M; Short, Philip A; Kim, Chang Soo; Burnette, Dylan T; Reilly, Matthew A; Murthy, N Sanjeeva; Kang, Mi-Lan; Kim, Won Shik; Sung, Hak-Joon

2017-07-12

Human bone marrow derived mesenchymal stem cells (hMSCs) hold great promise for regenerative medicine due to their multipotent differentiation capacity and immunomodulatory capabilities. Substantial research has elucidated mechanisms by which extracellular cues regulate hMSC fate decisions, but considerably less work has addressed how material properties can be leveraged to maintain undifferentiated stem cells. Here, we show that synthetic culture substrates designed to exhibit moderate cell-repellency promote high stemness and low oxidative stress-two indicators of naïve, healthy stem cells-in commercial and patient-derived hMSCs. Furthermore, the material-mediated effect on cell behavior can be tuned by altering the molar percentage (mol %) and/or chain length of poly(ethylene glycol) (PEG), the repellant block linked to hydrophobic poly(ε-caprolactone) (PCL) in the copolymer backbone. Nano- and angstrom-scale characterization of the cell-material interface reveals that PEG interrupts the adhesive PCL domains in a chain-length-dependent manner; this prevents hMSCs from forming mature focal adhesions and subsequently promotes cell-cell adhesions that require connexin-43. This study is the first to demonstrate that intrinsic properties of synthetic materials can be tuned to regulate the stemness and redox capacity of hMSCs and provides new insight for designing highly scalable, programmable culture platforms for clinical translation.

Alternating block polyurethanes based on PCL and PEG as potential nerve regeneration materials.

PubMed

Li, Guangyao; Li, Dandan; Niu, Yuqing; He, Tao; Chen, Kevin C; Xu, Kaitian

2014-03-01

Polyurethanes with regular and controlled block arrangement, i.e., alternating block polyurethanes (abbreviated as PUCL-alt-PEG) based on poly(ε-caprolactone) (PCL-diol) and poly(ethylene glycol) (PEG) was prepared via selectively coupling reaction between PCL-diol and diisocyanate end-capped PEG. Chemical structure, molecular weight, distribution, and thermal properties were systematically characterized by FTIR, (1)H NMR, GPC, DSC, and TGA. Hydrophilicity was studied by static contact angle of H2O and CH2I2. Film surface was observed by scanning electron microscope (SEM) and atomic force microscopy, and mechanical properties were assessed by universal test machine. Results show that alternating block polyurethanes give higher crystal degree, higher mechanical properties, and more hydrophilic and rougher (deep ravine) surface than their random counterpart, due to regular and controlled structure. Platelet adhesion illustrated that PUCL-alt-PEG has better hemocompatibility and the hemacompatibility was affected significantly by PEG content. Excellent hemocompatibility was obtained with high PEG content. CCK-8 assay and SEM observation revealed much better cell compatibility of fibroblast L929 and rat glial cells on the alternating block polyurethanes than that on random counterpart. Alternating block polyurethane PUC20-a-E4 with optimized composition, mechanical, surface properties, hemacompatibility, and highest cell growth and proliferation was achieved for potential use in nerve regeneration. Copyright © 2013 Wiley Periodicals, Inc.

Effects of block copolymer properties on nanocarrier protection from in vivo clearance

PubMed Central

D’Addio, Suzanne M.; Saad, Walid; Ansell, Steven M.; Squiers, John J.; Adamson, Douglas; Herrera-Alonso, Margarita; Wohl, Adam R.; Hoye, Thomas R.; Macosko, Christopher W.; Mayer, Lawrence D.; Vauthier, Christine; Prud’homme, Robert K.

2012-01-01

Drug nanocarrier clearance by the immune system must be minimized to achieve targeted delivery to pathological tissues. There is considerable interest in finding in vitro tests that can predict in vivo clearance outcomes. In this work, we produce nanocarriers with dense PEG layers resulting from block copolymer-directed assembly during rapid precipitation. Nanocarriers are formed using block copolymers with hydrophobic blocks of polystyrene (PS), poly-ε-caprolactone (PCL), poly-D,L-lactide (PLA), or poly-lactide-co-glycolide (PLGA), and hydrophilic blocks of polyethylene glycol (PEG) with molecular weights from 1.5 kg/mol to 9 kg/mol. Nanocarriers with paclitaxel prodrugs are evaluated in vivo in Foxn1nu mice to determine relative rates of clearance. The amount of nanocarrier in circulation after 4 h varies from 10% to 85% of initial dose, depending on the block copolymer. In vitro complement activation assays are conducted in an effort to correlate the protection of the nanocarrier surface from complement binding and activation and in vivo circulation. Guidelines for optimizing block copolymer structure to maximize circulation of nanocarriers formed by rapid precipitation and directed assembly are proposed, relating to the relative size of the hydrophilic and hydrophobic block, the hydrophobicity of the anchoring block, the absolute size of the PEG block, and polymer crystallinity. The in vitro results distinguish between the poorly circulating PEG5k-PCL9k and the better circulating nanocarriers, but could not rank the better circulating nanocarriers in order of circulation time. Analysis of PEG surface packing on monodisperse 200 nm latex spheres indicates that the sizes of the hydrophobic PCL, PS, and PLA blocks are correlated with the PEG blob size, and possibly the clearance from circulation. Suggestions for next step in vitro measurements are made. PMID:22732478

Nanoparticles Made From Xyloglucan-Block-Polycaprolactone Copolymers: Safety Assessment for Drug Delivery.

PubMed

Mazzarino, Letícia; Loch-Neckel, Gecioni; Dos Santos Bubniak, Lorena; Ourique, Fabiana; Otsuka, Issei; Halila, Sami; Curi Pedrosa, Rozangela; Santos-Silva, Maria Cláudia; Lemos-Senna, Elenara; Curti Muniz, Edvani; Borsali, Redouane

2015-09-01

Xyloglucan-block-polycaprolactone (XGO-PCL) copolymer nanoparticles have been proposed as nanocarriers for drug delivery. However, the possible harmful effects of exposure to nanoparticles still remain a concern. Therefore, the aim of this study is to evaluate the potential toxicity of XGO-PCL nanoparticles using in vitro and in vivo assays. Cytotoxicity and genotoxicity studies were conducted on MRC-5 human fetal lung fibroblast cells upon exposure to XGO-PCL nanoparticles. No significant reduction in the cell viability and no DNA damage were observed at the different concentrations tested. Erythrocyte toxicity was assessed by the incubation of nanoparticles with human blood. XGO-PCL nanoparticles induced a hemolytic ratio of less than 1%, indicating good blood compatibility. Finally, the subacute toxicity of XGO-PCL nanoparticles (10 mg/kg/day) was evaluated in BALB/c mice when administered orally or intraperitoneally for 14 days. Results of the in vivo toxicity study showed no clinical signs of toxicity, mortality, weight loss, or hematological and biochemical alterations after treatment with nanoparticles. Also, microscopic analysis of the major organs revealed no histopathological abnormalities, corroborating the previous results. Thus, it can be concluded that XGO-PCL nanoparticles induced no effect indicative of toxicity, indicating their potential use as drug delivery systems. © The Author 2015. Published by Oxford University Press on behalf of the Society of Toxicology. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Engineered electrospun poly(caprolactone)/polycaprolactone-g-hydroxyapatite nano-fibrous scaffold promotes human fibroblasts adhesion and proliferation.

PubMed

Keivani, F; Shokrollahi, P; Zandi, M; Irani, S; F Shokrolahi; Khorasani, S C

2016-11-01

Polycaprolactone (PCL)/hydroxyapatite nano-composites are among the best candidates for tissue engineering. However, interactions between nHAp and PCL are difficult to control leading to inhomogeneous dispersion of the bio-ceramic particles. Grafting of polymer chains at high density/chain length while promotes the phase compatibility may result in reduced HAp exposed surface area and therefore, bioactivity is compromised. This issue is addressed here by grafting PCL chains onto HAp nano-particles through ring opening polymerization of ε-caprolactone (PCL-g-HAp). FTIR and TGA analysis showed that PCL (6.9wt%), was successfully grafted on the HAp. PCL/PCL-g-HAp nano-fibrous scaffold showed up to 10 and 33% enhancement in tensile strength and modulus, respectively, compared to those of PCL/HAp. The effects of HAp on the in vitro HAp formation were investigated for both the PCL/HAp and PCL/PCL-g-HAp scaffolds. Precipitation of HAp on the nano-composite scaffolds observed after 15days incubation in simulated body fluid (SBF), as confirmed by scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). Human fibroblasts were seeded on PCL, PCL/HAp and PCL/PCL-g-HAp scaffolds. According to MTT assay, the highest cell proliferation was recorded for PCL/PCL-g-HAp nano-composite, at all time intervals (1-21days, P<0.001). Fluorescent microscopy (of DAPI stained samples) and electron microscopy images showed that all nano-fibrous scaffolds (PCL, PCL/HAp, and PCL/PCL-g-HAp), were non-toxic against cells, while more cell adhesion, and the most uniform cell distribution observed on the PCL/PCL-g-HAp. Overall, grafting of relatively short chains of PCL on the surface of HAp nano-particles stimulates fibroblasts adhesion and proliferation on the PCL/PCL-g-HAp nano-composite. Copyright © 2016 Elsevier B.V. All rights reserved.

Passive targeting of thermosensitive diblock copolymer micelles to the lungs: synthesis and characterization of poly(N-isopropylacrylamide)-block-poly(ε-caprolactone).

PubMed

Lee, Ren-Shen; Lin, Chih-Hung; Aljuffali, Ibrahim A; Hu, Kai-Yin; Fang, Jia-You

2015-06-18

Amphiphilic poly(N-isopropylacrylamide)-block-poly(ε-caprolactone) (PNiPAAm-b-PCL) copolymers were synthesized by ring-opening polymerization to form thermosensitive micelles as nanocarriers for bioimaging and carboplatin delivery. The critical micelle concentration increased from 1.8 to 3.5 mg/l following the decrease of the PNiPAAm chain length. The copolymers revealed a lower critical solution temperature (LCST) between 33 and 40°C. The copolymers self-assembled to form spherical particles of 146-199 nm in diameter. Carboplatin in micelles exhibited a slower release at 37°C relative to that at 25°C due to the gel layer formation on the micellar shell above the LCST. The micelles containing dye or carboplatin were intravenously injected into the rats for in vivo bioimaging and drug biodistribution. The bioimaging profiles showed a significant accumulation of micelles in the lungs. The micelles could minimize the reticuloendothelial system (RES) recognition of the dye. In vivo biodistribution demonstrated an improved pulmonary accumulation of carboplatin from 2.5 to 3.4 μg/mg by the micelles as compared to the control solution. Carboplatin accumulation in the heart and kidneys was reduced after encapsulation by the micelles. This study supports the potential of PNiPAAm-b-PCL micelles to passively target the lungs and attenuate RES uptake and possible side effects.

Effects of polycaprolactone-tricalcium phosphate, recombinant human bone morphogenetic protein-2 and dog mesenchymal stem cells on bone formation: pilot study in dogs.

PubMed

Kim, Sun-Jong; Kim, Myung-Rae; Oh, Jin-Sub; Han, Inho; Shin, Sang-Wan

2009-12-31

The aim of this study was to evaluate the survival, proliferation, and bone formation of dog mesenchymal stem cells (dMSCs) in the graft material by using Polycaprolactone-tricalcium phosphate (PCL-TCP), auto-fibrin glue (AFG), recombinant human bone morphogenetic protein-2 (rhBMP-2), and dMSCs after a transplantation to the scapula of adult beagle dogs. The subjects were two beagle dogs. Total dose of rhBMP-2 on each block was 10 microg with 50 microg/mg concentration. The cortical bone of the scapula of the dog was removed which was the same size of PCL-TCP block (Osteopore International Pte, Singapore; 5.0x5.0x8.0 mm in size), and the following graft material then was fixed with orthodontic mini-implant, Dual-top (Titanium alloy, Jeil Co. Seoul, Korea). Four experimental groups were prepared for this study, Group 1: PCL-TCP + aFG; Group 2: PCL-TCP + aFG + dMSCs; Group 3: PCL-TCP + aFG + dMSCs + rhBMP-2; Group 4: PCL-TCP + aFG + dMSCs + rhBMP-2 + PCL membrane. The survival or proliferation of dMSCs cells was identified with an extracted tissue through a fluorescence microscope, H-E staining and Von-Kossa staining in two weeks and four weeks after the transplantation. The survival and proliferation of dMSCs were identified through a fluorescence microscope from both Group 1 and Group 2 in two weeks and four weeks after the transplantation. Histological observation also found that the injected cells were proliferating well in the G2, G3, and G4 scaffolds. This study concluded that bone ingrowth occurred in PCL-TCP scaffold which was transplanted with rhBMP-2, and MSCs did not affect bone growth. More sufficient healing time would be needed to recognize effects of dMSCs on bone formation.

Comparison of 3D-Printed Poly-ɛ-Caprolactone Scaffolds Functionalized with Tricalcium Phosphate, Hydroxyapatite, Bio-Oss, or Decellularized Bone Matrix^.

PubMed

Nyberg, Ethan; Rindone, Alexandra; Dorafshar, Amir; Grayson, Warren L

2017-06-01

Three-dimensional (3D)-printing facilitates rapid, custom manufacturing of bone scaffolds with a wide range of material choices. Recent studies have demonstrated the potential for 3D-printing bioactive (i.e., osteo-inductive) scaffolds for use in bone regeneration applications. In this study, we 3D-printed porous poly-ɛ-caprolactone (PCL) scaffolds using a fused deposition modeling (FDM) process and functionalized them with mineral additives that have been widely used commercially and clinically: tricalcium phosphate (TCP), hydroxyapatite (HA), Bio-Oss (BO), or decellularized bone matrix (DCB). We assessed the "print quality" of the composite scaffolds and found that the print quality of PCL-TCP, PCL-BO, and PCL-DCB measured ∼0.7 and was statistically lower than PCL and PCL-HA scaffolds (∼0.8). We found that the incorporation of mineral particles did not significantly decrease the compressive modulus of the graft, which was on the order of 260 MPa for solid blocks and ranged from 32 to 83 MPa for porous scaffolds. Raman spectroscopy revealed the surfaces of the scaffolds maintained the chemical profile of their dopants following the printing process. We evaluated the osteo-inductive properties of each scaffold composite by culturing adipose-derived stromal/stem cells in vitro and assessing their differentiation into osteoblasts. The calcium content (normalized to DNA) increased significantly in PCL-TCP (p < 0.05), PCL-BO (p < 0.001), and PCL-DCB (p < 0.0001) groups relative to PCL only. The calcium content also increased in PCL-HA but was not statistically significant (p > 0.05). Collagen 1 expression was 10-fold greater than PCL in PCL-BO and PCL-DCB (p < 0.05) and osteocalcin expression was 10-fold greater in PCL-BO and PCL-DCB (p < 0.05) as measured by quantitative-real time-polymerase chain reaction. This study suggests that PCL-BO and PCL-DCB hybrid material may be advantageous for bone healing applications over PCL-HA or PCL-TCP blends.

The risk of sacrificing the PCL in cruciate retaining total knee arthroplasty and the relationship to the sagittal inclination of the tibial plateau.

PubMed

Sessa, Pasquale; Fioravanti, Giulio; Giannicola, Giuseppe; Cinotti, Gianluca

2015-01-01

In cruciate retaining total knee arthroplasty (TKA), a partial avulsion of PCL may occur when en-bloc tibial osteotomy is performed. We evaluated the effects of a tibial cut performed with different degrees of posterior slope on PCL insertion and whether the results are affected by the sagittal inclination of the patient's tibial plateau. We selected 83 MRIs of knees showing mild or no degenerative changes. The effects of a simulated tibial cut performed with a posterior slope of 0°, 3°, 5° and parallel to the patient's tibial plateau inclination on PCL insertion in the proximal tibia were investigated. The results were correlated with the degree of posterior inclination of the tibial plateau. Every angle we used for the tibial cut caused a PCL avulsion greater than 50%. The percentage of PCL avulsion significantly increased with increasing the posterior slope of the tibial cut. Patients with sagittal tibial plateau inclination <5° showed greater PCL avulsion than those with sagittal inclination >8°. Most of the PCL insertion is likely to be sacrificed when resection of the proximal tibia is performed en-block. The risk of PCL avulsion is reduced in patients showing a marked posterior inclination of the tibial plateau, but even in this group of patients a surgical technique aimed at sparing most of the PCL insertion is necessary. Copyright © 2014 Elsevier B.V. All rights reserved.

Novel degradable co-polymers of polypyrrole support cell proliferation and enhance neurite out-growth with electrical stimulation.

PubMed

Durgam, Hymavathi; Sapp, Shawn; Deister, Curt; Khaing, Zin; Chang, Emily; Luebben, Silvia; Schmidt, Christine E

2010-01-01

Synthetic polymers such as polypyrrole (PPy) are gaining significance in neural studies because of their conductive properties. We evaluated two novel biodegradable block co-polymers of PPy with poly(epsilon-caprolactone) (PCL) and poly(ethyl cyanoacrylate) (PECA) for nerve regeneration applications. PPy-PCL and PPy-PECA co-polymers can be processed from solvent-based colloidal dispersions and have essentially the same or greater conductivity (32 S/cm for PPy-PCL, 19 S/cm for PPy-PECA) compared to the PPy homo-polymer (22 S/cm). The PPy portions of the co-polymers permit electrical stimulation whereas the PCL or PECA blocks enable degradation by hydrolysis. For in vitro tests, films were prepared on polycarbonate sheets by air brushing layers of dispersions and pressing the films. We characterized the films for hydrolytic degradation, electrical conductivity, cell proliferation and neurite extension. The co-polymers were sufficient to carry out electrical stimulation of cells without the requirement of a metallic conductor underneath the co-polymer film. In vitro electrical stimulation of PPy-PCL significantly increased the number of PC12 cells bearing neurites compared to unstimulated PPy-PCL. For in vivo experiments, the PPy co-polymers were coated onto the inner walls of nerve guidance channels (NGCs) made of the commercially available non-conducting biodegradable polymer poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHB-HV). The NGCs were implanted in a 10 mm defect made in the sciatic nerve of rats, and harvested after 8 weeks. Histological staining showed axonal growth. The studies indicated that these new conducting degradable biomaterials have good biocompatibility and support proliferation and growth of PC12 cells in vitro (with and without electrical stimulation) and neurons in vivo (without electrical stimulation).

Antibacterial modification of an injectable, biodegradable, non-cytotoxic block copolymer-based physical gel with body temperature-stimulated sol-gel transition and controlled drug release.

PubMed

Wang, Xiaowen; Hu, Huawen; Wang, Wenyi; Lee, Ka I; Gao, Chang; He, Liang; Wang, Yuanfeng; Lai, Chuilin; Fei, Bin; Xin, John H

2016-07-01

Biomaterials are being extensively used in various biomedical fields; however, they are readily infected with microorganisms, thus posing a serious threat to the public health care. We herein presented a facile route to the antibacterial modification of an important A-B-A type biomaterial using poly (ethylene glycol) methyl ether (mPEG)- poly(ε-caprolactone) (PCL)-mPEG as a typical model. Inexpensive, commercial bis(2-hydroxyethyl) methylammonium chloride (DMA) was adopted as an antibacterial unit. The effective synthesis of the antibacterial copolymer mPEG-PCL-∼∼∼-PCL-mPEG (where ∼∼∼ denotes the segment with DMA units) was well confirmed by FTIR and (1)H NMR spectra. At an appropriate modification extent, the DMA unit could render the copolymer mPEG-PCL-∼∼∼-PCL-mPEG highly antibacterial, but did not largely alter its fascinating intrinsic properties including the thermosensitivity (e.g., the body temperature-induced sol-gel transition), non-cytotoxicity, and controlled drug release. A detailed study on the sol-gel-sol transition behavior of different copolymers showed that an appropriate extent of modification with DMA retained a sol-gel-sol transition, despite the fact that a too high extent caused a loss of sol-gel-sol transition. The hydrophilic and hydrophobic balance between mPEG and PCL was most likely broken upon a high extent of quaternization due to a large disturbance effect of DMA units at a large quantity (as evidenced by the heavily depressed PCL segment crystallinity), and thus the micelle aggregation mechanism for the gel formation could not work anymore, along with the loss of the thermosensitivity. The work presented here is highly expected to be generalized for synthesis of various block copolymers with immunity to microorganisms. Light may also be shed on understanding the phase transition behavior of various multiblock copolymers. Copyright © 2016 Elsevier B.V. All rights reserved.

Stellate ganglion block used to treat symptoms associated with combat-related post-traumatic stress disorder: a case series of 166 patients.

PubMed

Mulvaney, Sean W; Lynch, James H; Hickey, Matthew J; Rahman-Rawlins, Tabassum; Schroeder, Matthew; Kane, Shawn; Lipov, Eugene

2014-10-01

Report the successful use of stellate ganglion blocks (SGBs) in 166 active duty service members with multiple combat deployments experiencing anxiety symptoms associated with post-traumatic stress disorder (PTSD). Successful treatment of PTSD symptoms with SGB has been reported previously. This is the largest published case series evaluating SGB with a minimum of 3 months follow-up. Following clinical interview including administration of the PTSD Checklist (PCL), 166 service members with symptoms of PTSD elected to receive a SGB. All patients received a SGB on the right side at the level of the sixth cervical vertebrae (C6). The PCL was administered the day before treatment to establish a baseline, repeated 1 week later, and then monthly out to 3 months. A positive response was considered to be an improvement in the PCL score by 10 or greater points. Follow-up PCL scores from 3 to 6 months were obtained and analyzed for 166 patients. In a military population with multiple combat deployments, over 70% of the patients treated had a clinically significant improvement in their PCL score which persisted beyond 3 to 6 months postprocedure. Selective blockade of the right cervical sympathetic chain at the C6 level is a safe and minimally invasive procedure that may provide durable relief from anxiety symptoms associated with PTSD. Reprint & Copyright © 2014 Association of Military Surgeons of the U.S.

Porous inorganic-organic shape memory polymers.

PubMed

Zhang, Dawei; Burkes, William L; Schoener, Cody A; Grunlan, Melissa A

2012-06-21

Thermoresponsive shape memory polymers (SMPs) are a type of stimuli-sensitive materials that switch from a temporary shape back to their permanent shape upon exposure to heat. While the majority of SMPs have been fabricated in the solid form, porous SMP foams exhibit distinct properties and are better suited for certain applications, including some in the biomedical field. Like solid SMPs, SMP foams have been restricted to a limited group of organic polymer systems. In this study, we prepared inorganic-organic SMP foams based on the photochemical cure of a macromer comprised of inorganic polydimethylsiloxane (PDMS) segments and organic poly(ε-caprolactone) (PCL) segments, diacrylated PCL(40)-block-PDMS(37)-block-PCL(40). To achieve tunable pore size with high interconnectivity, the SMP foams were prepared via a refined solvent-casting/particulate-leaching (SCPL) method. By varying design parameters such as degree of salt fusion, macromer concentration in the solvent and salt particle size, the SMP foams with excellent shape memory behavior and tunable pore size, pore morphology, and modulus were obtained.

Scaffolds from block polyurethanes based on poly(ɛ-caprolactone) (PCL) and poly(ethylene glycol) (PEG) for peripheral nerve regeneration.

PubMed

Niu, Yuqing; Chen, Kevin C; He, Tao; Yu, Wenying; Huang, Shuiwen; Xu, Kaitian

2014-05-01

Nerve guide scaffolds from block polyurethanes without any additional growth factors or protein were prepared using a particle leaching method. The scaffolds of block polyurethanes (abbreviated as PUCL-ran-EG) based on poly(ɛ-caprolactone) (PCL-diol) and poly(ethylene glycol) (PEG) possess highly surface-area porous for cell attachment, and can provide biochemical and topographic cues to enhance tissue regeneration. The nerve guide scaffolds have pore size 1-5 μm and porosity 88%. Mechanical tests showed that the polyurethane nerve guide scaffolds have maximum loads of 4.98 ± 0.35 N and maximum stresses of 6.372 ± 0.5 MPa. The histocompatibility efficacy of these nerve guide scaffolds was tested in a rat model for peripheral nerve injury treatment. Four types of guides including PUCL-ran-EG scaffolds, autograft, PCL scaffolds and silicone tubes were compared in the rat model. After 14 weeks, bridging of a 10 mm defect gap by the regenerated nerve was observed in all rats. The nerve regeneration was systematically characterized by sciatic function index (SFI), histological assessment including HE staining, immunohistochemistry, ammonia silver staining, Masson's trichrome staining and TEM observation. Results revealed that polyurethane nerve guide scaffolds exhibit much better regeneration behavior than PCL, silicone tube groups and comparable to autograft. Electrophysiological recovery was also seen in 36%, 76%, and 87% of rats in the PCL, PUCL-ran-EG, and autograft groups respectively, whilst 29.8% was observed in the silicone tube groups. Biodegradation in vitro and in vivo show proper degradation of the PUCL-ran-EG nerve guide scaffolds. This study has demonstrated that without further modification, plain PUCL-ran-EG nerve guide scaffolds can help peripheral nerve regeneration excellently. Copyright © 2014 Elsevier Ltd. All rights reserved.

Laser-treated electrospun fibers loaded with nano-hydroxyapatite for bone tissue engineering.

PubMed

Aragon, Javier; Navascues, Nuria; Mendoza, Gracia; Irusta, Silvia

2017-06-15

Core-shell polycaprolactone/polycaprolactone (PCL/PCL) and polycaprolactone/polyvinyl acetate (PCL/PVAc) electrospun fibers loaded with synthesized nanohydroxyapatite (HAn) were lased treated to create microporosity. The prepared materials were characterized by XRD, FTIR, TEM and SEM. Uniform and randomly oriented beadless fibrous structures were obtained in all cases. Fibers diameters were in the 150-300nm range. Needle-like HAn nanoparticles with mean diameters of 20nm and length of approximately 150nm were mostly encase inside the fibers. Laser treated materials present micropores with diameters in the range 70-120μm for PCL-HAn/PCL fibers and in the 50-90μm range for PCL-HAn/PVAC material. Only samples containing HAn presented bioactivity after incubation during 30days in simulated body fluid. All scaffolds presented high viability, very low mortality, and human osteoblast proliferation. Biocompatibility was increased by laser treatment due to the surface and porosity modification. Copyright © 2017 Elsevier B.V. All rights reserved.

Hemocompatibility evaluation in vitro of methoxy polyethyleneglycol-polycaprolactone copolymer solutions.

PubMed

Hu, Qian; Zhang, Yi; Wang, Changyong; Xu, Jiake; Wu, Jianping; Liu, Zonghua; Xue, Wei

2016-03-01

Amphiphilic block copolymer methoxy polyethyleneglycol-polycaprolactone (mPEG-PCL) has attracted interest in the biomedical field, due to its water solubility and biodegradability. Nevertheless, the blood safety of mPEG-PCL copolymers has not been investigated in detail. Because mPEG-PCL copolymers introduced in vivo would inevitably interact with blood tissue, an investigation of possible interactions of mPEG-PCL with key blood components is crucial. We studied the effects of two mPEG-PCL copolymer solutions on blood coagulation, the morphology and lysis of human red blood cells (RBCs), the structure of plasma fibrinogen, complement activation, and platelet aggregation. We found that higher concentrations of the mPEG-PCL copolymers impaired blood clotting, and the copolymers had little impact on the morphology or lysis of RBCs. From the spectroscopy results, the copolymers affected the local microstructure of fibrinogen. The copolymers significantly activated the complement system in a concentration-dependent way. At higher concentrations, the copolymers impaired platelet aggregation, which may have been mediated by an inhibition of the arachidonic acid pathway. These findings provide important information that may be useful for the molecular design and biomedical applications of mPEG-PCL copolymers. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 802-812, 2016. © 2016 Wiley Periodicals, Inc.

Block Copolymer Micelles as Nanocontainers for Controlled Release of Proteins from Biocompatible Oil Phases

PubMed Central

2009-01-01

Biocompatible oils are used in a variety of medical applications ranging from vaccine adjuvants to vehicles for oral drug delivery. To enable such nonpolar organic phases to serve as reservoirs for delivery of hydrophilic compounds, we explored the ability of block copolymer micelles in organic solvents to sequester proteins for sustained release across an oil−water interface. Self-assembly of the block copolymer, poly(ϵ-caprolactone)-block-poly(2-vinyl pyridine) (PCL-b-P2VP), was investigated in toluene and oleic acid, a biocompatible naturally occurring fatty acid. Micelle formation in toluene was characterized by dynamic light scattering (DLS) and atomic force microscopy (AFM) imaging of micelles cast onto silicon substrates. Cryogenic transmission electron microscopy confirmed a spherical morphology in oleic acid. Studies of homopolymer solubility implied that micelles in oleic acid consist of a P2VP corona and a PCL core, while P2VP formed the core of micelles assembled in toluene. The loading of two model proteins (ovalbumin (ova) and bovine serum albumin (BSA)) into micelles was demonstrated with loadings as high as 7.8% wt of protein per wt of P2VP in oleic acid. Characterization of block copolymer morphology in the two solvents after protein loading revealed spherical particles with similar size distributions to the as-assembled micelles. Release of ova from micelles in oleic acid was sustained for 12−30 h upon placing the oil phase in contact with an aqueous bath. Unique to the situation of micelle assembly in an oily phase, the data suggest protein is sequestered in the P2VP corona block of PCL-b-P2VP micelles in oleic acid. More conventionally, protein loading occurs in the P2VP core of micelles assembled in toluene. PMID:19235932

Reduction-responsive PEtOz-SS-PCL micelle with tailored size to overcome blood-brain barrier and enhance doxorubicin antiglioma effect.

PubMed

Li, Yuling; Baiyang, Li; Leran, Bu; Zhen, Wang; Yandong, Xie; Baixiang, Du; Dandan, Zhu; Yufu, Zhu; Jun, Liang; Rutong, Yu; Hongmei, Liu

2017-11-01

A series of novel reduction-responsive micelles with tailored size were designed and prepared to release doxorubicin (DOX) for treating glioma, which were developed based on amphiphilic block copolymer poly (2-ethyl-2-oxazoline)-b-poly (ε-caprolactone) (PEtOz-SS-PCL) and the micelle size could be regulated by designing the polymer structure. The DOX-loaded PEtOz-SS-PCL micelles had small size and rapid drug release in reductive intracellular environments. Biodistribution and in vivo imaging studies in C6 glioma mice tumor model showed that DOX loaded PEtOz-SS-PCL43 micelles with the smallest size had superior accumulation and fast drug release in tumor sites. In vivo antitumor activity demonstrated that DOX-loaded PEtOz-SS-PCL43 micelles improved antitumor efficacy in contrast to PEtOz-SS-PCL micelles with larger size toward the orthotopic C6-Luci cells-bearing mice. This study shows great potential in tailoring the micelle size and introducing the responsive bonds or compartment for intracellular drug delivery and release in glioma treatment by designing the architecture of the polymer.

Curcumin-Loaded Blood-Stable Polymeric Micelles for Enhancing Therapeutic Effect on Erythroleukemia.

PubMed

Gong, Feirong; Chen, Dan; Teng, Xin; Ge, Junhua; Ning, Xianfeng; Shen, Ya-Ling; Li, Jian; Wang, Shanfeng

2017-08-07

Curcumin has high potential in suppressing many types of cancer and overcoming multidrug resistance in a multifaceted manner by targeting diverse molecular targets. However, the rather low systemic bioavailability resulted from its poor solubility in water and fast metabolism/excretion in vivo has hampered its applications in cancer therapy. To increase the aqueous solubility of curcumin while retaining the stability in blood circulation, here we report curcumin-loaded copolymer micelles with excellent in vitro and in vivo stability and antitumor efficacy. The two copolymers used for comparison were methoxy-poly(ethylene glycol)-block-poly(ε-caprolactone) (mPEG-PCL) and N-(tert-butoxycarbonyl)-l-phenylalanine end-capped mPEG-PCL (mPEG-PCL-Phe(Boc)). In vitro cytotoxicity evaluation against human pancreatic SW1990 cell line showed that the delivery of curcumin in mPEG-PCL-Phe(Boc) micelles to cancer cells was efficient and dosage-dependent. The pharmacokinetics in ICR mice indicated that intravenous (i.v.) administration of curcumin/mPEG-PCL-Phe(Boc) micelles could retain curcumin in plasma much better than curcumin/mPEG-PCL micelles. Biodistribution results in Sprague-Dawley rats also showed higher uptake and slower elimination of curcumin into liver, lung, kidney, and brain, and lower uptake into heart and spleen of mPEG-PCL-Phe(Boc) micelles, as compared with mPEG-PCL micelles. Further in vivo efficacy evaluation in multidrug-resistant human erythroleukemia K562/ADR xenograft model revealed that i.v. administration of curcumin-loaded mPEG-PCL-Phe(Boc) micelles significantly delayed tumor growth, which was attributed to the improved stability of curcumin in the bloodstream and increased systemic bioavailability. The mPEG-PCL-Phe(Boc) micellar system is promising in overcoming the key challenge of curcumin's to promote its applications in cancer therapy.

Amphiphilic multiarm star block copolymer-based multifunctional unimolecular micelles for cancer targeted drug delivery and MR imaging.

PubMed

Li, Xiaojie; Qian, Yinfeng; Liu, Tao; Hu, Xianglong; Zhang, Guoying; You, Yezi; Liu, Shiyong

2011-09-01

We report on the fabrication of multifunctional polymeric unimolecular micelles as an integrated platform for cancer targeted drug delivery and magnetic resonance imaging (MRI) contrast enhancement under in vitro and in vivo conditions. Starting from a fractionated fourth-generation hyperbranched polyester (Boltorn H40), the ring-opening polymerization of ɛ-caprolactone (CL) from the periphery of H40 and subsequent terminal group esterification with 2-bromoisobutyryl bromide afforded star copolymer-based atom transfer radical polymerization (ATRP) macroinitiator, H40-PCL-Br. Well-defined multiarm star block copolymers, H40-PCL-b-P(OEGMA-co-AzPMA), were then synthesized by the ATRP of oligo(ethylene glycol) monomethyl ether methacrylate (OEGMA) and 3-azidopropyl methacrylate (AzPMA). This was followed by the click reaction of H40-PCL-b-P(OEGMA-co-AzPMA) with alkynyl-functionalized cancer cell-targeting moieties, alkynyl-folate, and T(1)-type MRI contrast agents, alkynyl-DOTA-Gd (DOTA is 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetrakisacetic acid), affording H40-PCL-b-P(OEGMA-Gd-FA). In aqueous solution, the amphiphilic multiarm star block copolymer exists as structurally stable unimolecular micelles possessing a hyperbranched polyester core, a hydrophobic PCL inner layer, and a hydrophilic P(OEGMA-Gd-FA) outer corona. H40-PCL-b-P(OEGMA-Gd-FA) unimolecular micelles are capable of encapsulating paclitaxel, a well-known hydrophobic anticancer drug, with a loading content of 6.67 w/w% and exhibiting controlled release of up to 80% loaded drug over a time period of ∼120 h. In vitro MRI experiments demonstrated considerably enhanced T(1) relaxivity (18.14 s(-1) mM(-1)) for unimolecular micelles compared to 3.12 s(-1) mM(-1) for that of the small molecule counterpart, alkynyl-DOTA-Gd. Further experiments of in vivo MR imaging in rats revealed good accumulation of unimolecular micelles within rat liver and kidney, prominent positive contrast enhancement, and relatively long duration of blood circulation. The reported unimolecular micelles-based structurally stable nanocarriers synergistically integrated with cancer targeted drug delivery and controlled release and MR imaging functions augur well for their potential applications as theranostic systems. Copyright © 2011 Elsevier Ltd. All rights reserved.

Temperature-responsive in situ nanoparticle hydrogels based on hydrophilic pendant cyclic ether modified PEG-PCL-PEG.

PubMed

Feng, Zujian; Zhao, Junqiang; Li, Yin; Xu, Shuxin; Zhou, Junhui; Zhang, Jianhua; Deng, Liandong; Dong, Anjie

2016-10-20

Thermo-sensitive injectable hydrogels based on poly(ε-caprolactone)/poly(ethylene glycol) (PCL/PEG) block copolymers have attracted considerable attention for sustained drug release and tissue engineering applications. Previously, we have reported a thermo-sensitive hydrogel of P(CL-co-TOSUO)-PEG-P(CL-co-TOSUO) (PECT) triblock copolymers modified by hydrophilic cyclic ether pendant groups 1,4,8-trioxa-[4.6]spiro-9-undecanone (TOSUO). Unfortunately, the low gel modulus of PECT (only 50-70 Pa) may limit its applications. Herein, another kind of thermogelling triblock copolymer of a pendant cyclic ether-modified caprolactonic poloxamer analog, PEG-P(CL-co-TOSUO)-PEG (PECTE), was successfully prepared by control of the hydrophilicity/hydrophobicity balance and chemical compositions of the copolymers. PECTE powder could directly disperse in water to form a stable nanoparticle (NP) aqueous dispersion and underwent sol-gel-sol transition behavior at a higher concentration with the temperature increasing from ambient or lower temperatures. Significantly, the microstructure parameters (e.g., different chemical compositions of the hydrophobic block and topology) played a critical role in the phase transition behavior. Furthermore, comparison studies on PECTE and PEG-PCL-PEG (PECE) showed that the introduction of pendant cyclic ether groups into PCL blocks could avoid unexpected ahead-of-time gelling of the PECE aqueous solution. In addition, the rheological analysis of PECTE and PECT indicated that the storage modulus of the PECTE hydrogel could be 100 times greater than that of the PECT hydrogel under the same mole ratios of TOSUO/CL and lower molecular weight. Consequently, PECTE thermal hydrogel systems are believed to be promising as in situ gel-forming biomaterials for drug delivery and tissue engineering.

Enhanced bone screw fixation with biodegradable bone cement in osteoporotic bone model.

PubMed

Juvonen, Tiina; Koistinen, Arto; Kröger, Heikki; Lappalainen, Reijo

2012-09-27

The purpose of this study was to study the potential of novel biodegradable PCL bone cement to improve bone screw fixation strength in osteoporotic bone. The biomechanical properties of bone cement (ε-polycaprolactone, PCL) and fixation strength were studied using biomechanical tests and bone screws fixed in an osteoporotic bone model. Removal torques and pullout strengths were assessed for cortical, self-tapping, and cancellous screws inserted in the osteoporotic bone model (polyurethane foam blocks with polycarbonate plate) with and without PCL bone cement. Open cell and cellular rigid foam blocks with a density of 0.12 g/cm3 were used in this model. Removal torques were significantly (more than six-fold) improved with bone cement for cancellous screws. Furthermore, the bone cement improved pullout strengths three to 12 times over depending on the screw and model material. Biodegradable bone cement turned out to be a very potential material to stabilize screw fixation in osteoporotic bone. The results warrant further research before safe clinical use, especially to clarify clinically relevant factors using real osteoporotic bone under human body conditions and dynamic fatigue testing for long-term performance.

Structurally Stable Attractive Nanoscale Emulsions with Dipole-Dipole Interaction-Driven Interdrop Percolation.

PubMed

Shin, Kyounghee; Gong, Gyeonghyeon; Cuadrado, Jonas; Jeon, Serim; Seo, Mintae; Choi, Hong Sung; Hwang, Jae Sung; Lee, Youngbok; Fernandez-Nieves, Alberto; Kim, Jin Woong

2017-03-28

This study introduces an extremely stable attractive nanoscale emulsion fluid, in which the amphiphilic block copolymer, poly(ethylene oxide)-block-poly(ϵ-caprolactone) (PEO-b-PCL), is tightly packed with lecithin, thereby forming a mechanically robust thin-film at the oil-water interface. The molecular association of PEO-b-PCL with lecithin is critical for formation of a tighter and denser molecular assembly at the interface, which is systematically confirmed by T 2 relaxation and DSC analyses. Moreover, suspension rheology studies also reflect the interdroplet attractions over a wide volume fraction range of the dispersed oil phase; this results in a percolated network of stable drops that exhibit no signs of coalescence or phase separation. This unique rheological behavior is attributed to the dipolar interaction between the phosphorylcholine groups of lecithin and the methoxy end groups of PEO-b-PCL. Finally, the nanoemulsion system significantly enhances transdermal delivery efficiency due to its favorable attraction to the skin, as well as high diffusivity of the nanoscale emulsion drops. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

In vitro controlled release of clove essential oil in self-assembly of amphiphilic polyethylene glycol-block-polycaprolactone.

PubMed

Thonggoom, O; Punrattanasin, N; Srisawang, N; Promawan, N; Thonggoom, R

2016-05-01

In this study, a micellar delivery system with an amphiphilic diblock copolymer of poly (ethylene glycol) and poly (ɛ-caprolactone) was synthesised and used to incorporate hydrophobic clove essential oil (CEO). To determine an optimal delivery system, the effects of the copolymer's hydrophobic block length and the CEO-loading content on the encapsulation of CEO were investigated. Percentages of entrapment efficiency (%EE), CEO loading (%CEO), and in vitro release profiles were determined. The size, size distribution, zeta potential, and morphology of the obtained micelles were determined by DLS, FE-SEM, and TEM. The %EE, %CEO, and in vitro release profiles of CEO incorporated in micelles were analysed by HPLC. The study revealed a sustained release profile of CEO from CEO-loaded micelles. The results indicate the successful formulation of CEO-loaded PEG-b-PCL micelle nanoparticles. It is suggested that this micelle system has considerably potential applications in the sustained release of CEO in intravascular drug delivery.

Surface modification of Polycaprolactone (PCL) microcarrier for performance improvement of human skin fibroblast cell culture

NASA Astrophysics Data System (ADS)

Samsudin, N.; Hashim, Y. Z. H.; Arifin, M. A.; Mel, M.; Salleh, H. Mohd; Sopyan, I.; Hamid, M. Abdul

2018-01-01

Polycaprolactone (PCL) has many advantages for use in biomedical engineering field. In the present work PCL microcarriers of 150-200 μm were fabricated using oil-in-water (o/w) emulsification coupled with solvent evaporation method. The surface charge of PCL microcarrier was then been improved by using ultraviolet/ozone treatment to introduce oxygen functional group. Immobilisation of gelatin onto PCL microspheres using zero-length crosslinker provides a stable protein-support complex, with no diffusional barrier which is ideal for mass processing. The optimum concentration of carboxyl group (COOH) absorbed on the surface was 1495.9 nmol/g and the amount of gelatin immobilized was 1797.3 μg/g on UV/O3 treated microcarriers as compared to the untreated (320 μg/g) microcarriers. The absorption of functional oxygen groups on the surface and the immobilized gelatin was confirmed with Fourier Transformed Infrared spectroscopy and the enhancement of hydrophilicity of the surface was confirmed using water contact angle measurement which decreased (86.93° - 49.34°) after UV/O3 treatment and subsequently after immobilisation of gelatin. The attachment and growth kinetics for human skin fibroblast cell (HSFC) showed that adhesion occurred much more rapidly for gelatin immobilised surface as compared to untreated PCL and UV/O3 PCL microcarrier.

Redox-sensitive micelles assembled from amphiphilic mPEG-PCL-SS-DTX conjugates for the delivery of docetaxel.

PubMed

Zhang, Huiyuan; Wang, Kaiming; Zhang, Pei; He, Wenxiu; Song, Aixin; Luan, Yuxia

2016-06-01

Docetaxel (DTX) can produce anti-tumor effects by inhibiting cell growth and inducing apoptosis. However, the poor solubility of DTX restricts its application and its clinical formulation has caused serious adverse reaction due to the use of Tween-80. In the present study, DTX was conjugated to an amphiphilic di-block polymer to solve these problems. Methoxy poly(ethylene glycol)-poly(ε-caprolactone) (mPEG-PCL) was selected as the polymer skeleton and a redox sensitive disulfide bond was used as the linker between DTX and mPEG-PCL. The synthesized mPEG-PCL-SS-DTX conjugates were characterized by (1)H-nuclear magnetic resonance ((1)H NMR) and Fourier transform infrared spectroscopy (FTIR). Interestingly, the mPEG-PCL-SS-DTX conjugates could self-assemble into micelles in aqueous solution. The critical micelle concentration (CMC) of mPEG-PCL-SS-DTX micelles was about 2.3mgL(-1) determined using pyrene molecule fluorescent probe method while the size of mPEG-PCL-SS-DTX micelles was determined to be ca. 17.6nm and 116.0nm with a bimodal distribution by dynamic light scattering (DLS). The in vitro release results indicated that the as-prepared micelles exhibited a sustained release profile with good redox sensitive properties. In particular, the hemolytic toxicity test indicated the as-prepared mPEG-PCL-SS-DTX micelles had negligible hemolytic activity, demonstrating their safety in drug delivery system. Cytotoxicity assay of the mPEG-PCL-SS-DTX micelles verified their highly enhanced cytotoxicity to MCF-7/A and A549 cells. These results thus demonstrated that the present redox-sensitive mPEG-PCL-SS-DTX micelle was an efficient and safe sustained drug delivery system in the biomedical area. Copyright © 2016 Elsevier B.V. All rights reserved.

Self-Consistency of the Lauritzen-Hoffman and Strobl Models of Polymer Crystallization Evaluated for Poly(epsilon-caprolactone) Fractions and Effect of Composition on the Phenomenon of Concurrent Crystallization in Polyethylene Blends

NASA Astrophysics Data System (ADS)

Sheth, Swapnil Suhas

Narrow molecular weight fractions of poly(epsilon-caprolactone) were successfully obtained using the successive precipitation fractionation technique with toluene/n-heptane as a solvent/nonsolvent pair. Calorimetric studies of the melting behavior of fractions that were crystallized either isothermally or under constant cooling rate conditions suggested that the isothermal crystallization of the samples should be used for a proper evaluation of the molecular weight dependence of the observed melting temperature and degree of crystallinity in PCL. The molecular weight and temperature dependence of the spherulitic growth rate of fractions was studied in the context of the Lauritzen-Hoffman two-phase model and the Strobl three-phase model of polymer crystallization. The zero-growth rate temperatures, determined from spherulitic growth rates using four different methods, are consistent with each other and increase with chain length. The concomitant increase in the apparent secondary nucleation constant was attributed to two factors. First, for longer chains there is an increase in the probability that crystalline stems belong to loose chain-folds, hence, an increase in fold surface free energy. It is speculated that the increase in loose folding and resulting decrease in crystallinity with increasing chain length are associated with the ester group registration requirement in PCL crystals. The second contribution to the apparent nucleation constant arises from chain friction associated with segmental transport across the melt/crystal interface. These factors were responsible for the much stronger chain length dependence of spherulitic growth rates at fixed undercooling observed here with PCL than previously reported for PE and PEO. In the case of PCL, the scaling exponent associated with the chain length dependence of spherulitic growth rates exceeds the upper theoretical bound of 2 predicted from the Brochard- DeGennes chain pullout model. Observation that zero-growth and equilibrium melting temperature values are identical with each other within the uncertainty of their determinations casts serious doubt on the validity of Strobl three-phase model. A novel method is proposed to determine the Porod constant necessary to extrapolate the small angle X-ray scattering intensity data to large scattering vectors. The one-dimensional correlation function determined using this Porod constant yielded the values of lamellar crystal thickness, which were similar to these estimated using the Hosemann-Bagchi Paracrystalline Lattice model. The temperature dependence of the lamellar crystal thickness was consistent with both LH and the Strobl model of polymer crystallization. However, in contrast to the predictions of Strobl's model, the value of the mesomorph-to-crystal equilibrium transition temperature was very close to the zero-growth temperature. Moreover, the lateral block sizes (obtained using wide angle X-ray diffraction) and the lamellar thicknesses were not found to be controlled by the mesomorph-to-crystal equilibrium transition temperature. Hence, we concluded that the crystallization of PCL is not mediated by a mesophase. Metallocene-catalyzed linear low-density (m-LLDPE with 3.4 mol% 1-octene) and conventional low-density (LDPE) polyethylene blends of different compositions were investigated for their melt-state miscibility and concurrent crystallization tendency. Differential scanning calorimetric studies and morphological studies using atomic force microscopy confirm that these blends are miscible in the melt-state for all compositions. LDPE chains are found to crystallize concurrently with m-LLDPE chains during cooling in the m-LLDPE crystallization temperature range. While the extent of concurrent crystallization was found to be optimal in .. .. iv blends with highest m-LLDPE content studied, strong evidence was uncovered for the existence of a saturation effect in the concurrent crystallization behavior. This observation leads us to suggest that co-crystallization, rather than mere concurrent crystallization, of LDPE with m- LLDPE can indeed take place. Matching of the respective sequence length distributions in LDPE and m-LLDPE is suggested to control the extent of co-crystallization.

Near-infrared light-triggered thermochemotherapy of cancer using a polymer-gold nanorod conjugate

NASA Astrophysics Data System (ADS)

Ko, Hyewon; Son, Soyoung; Bae, Seonghwan; Kim, Joo-Hyung; Yi, Gi-Ra; Park, Jae Hyung

2016-04-01

A biocompatible polymer-gold nanorod (P-AuNR) conjugate was developed as a thermo-chemotherapeutic nano-sized drug carrier for cancer therapy using near-infrared (NIR) light as an external trigger. The amphiphilic polymer, poly(ethylene glycol)-block-poly(caprolactone) (PEG-b-PCL) bearing a disulfide bond, was prepared using a facile synthetic route via copper(I)-free click chemistry and covalently linked to AuNR. The chemical structures and successful conjugation of PEG-b-PCL were analyzed using 1H NMR and FT-IR. Doxorubicin (DOX), a hydrophobic anticancer drug, was effectively loaded into the hydrophobic PCL domain of P-AuNR through a simple dialysis method. P-AuNR showed longitudinal plasmon resonance absorption at the NIR region, thus generating heat under irradiation at 808 nm. Interestingly, exposure of P-AuNRs to NIR induced a structural change in the PCL block from a crystalline to an amorphous state, leading to the temporally controlled release of DOX. No significant release of DOX was observed from P-AuNRs under physiological conditions (pH 7.4), whereas the release rate of DOX was remarkably enhanced in response to NIR irradiation. In vitro cellular experiments to assess cytotoxicity and intracellular drug release behavior of DOX-P-AuNRs demonstrated that the release of DOX could be selectively regulated by NIR irradiation. Overall, DOX-P-AuNRs might have the potential to overcome the indiscriminate toxicity of free DOX.

Magnetic resonance imaging of the posterior cruciate ligament in flexion.

PubMed

Craddock, William; Smithers, Troy; Harris, Craig; du Moulin, William; Molnar, Robert

2018-06-01

Posterior cruciate ligament (PCL) injuries of the knee are common and sometimes difficult to diagnose. Magnetic resonance imaging (MRI), performed using standard orthogonal plane views, is the investigation of choice. It can be particularly difficult to differentiate acute partial and complete tears and identify elongation of chronic healed tears. The aim of the paper is to describe a new method of positioning the patient with the knee flexed at 90°, allowing the PCL to be visualised in a position of greatest length and tension which may assist in differentiating and identifying these injuries. Four symptomatic patients with suspected PCL injuries, two acute and two chronic, were MRI scanned using a routine protocol with the knee in extension before performing oblique sagittal fast spin-echo (FSE) proton-density (PD) sequences with the knee positioned in 90° of flexion. The appearance of the PCLs were then qualitatively assessed. MRI scanning with the knee in flexion identified more extensive PCL injury than standard imaging. In the two patients with acute injuries, partial tears on the standard orthogonal plane views were found to be complete ruptures. In the two patients with chronic injuries, elongation of the PCL not identifiable on the standard orthogonal plane views was apparent. MRI scanning of the PCL with the knee flexed at 90° may help in differentiating partial and complete ruptures of the PCL and identifying elongation of the PCL in chronic injuries. Copyright © 2018 Elsevier B.V. All rights reserved.

Synthesis of amphiphilic tadpole-shaped linear-cyclic diblock copolymers via ring-opening polymerization directly initiating from cyclic precursors and their application as drug nanocarriers.

PubMed

Wan, Xuejuan; Liu, Tao; Liu, Shiyong

2011-04-11

We report on the facile synthesis of well-defined amphiphilic and thermoresponsive tadpole-shaped linear-cyclic diblock copolymers via ring-opening polymerization (ROP) directly initiating from cyclic precursors, their self-assembling behavior in aqueous solution, and the application of micellar assemblies as controlled release drug nanocarriers. Starting from a trifunctional core molecule containing alkynyl, hydroxyl, and bromine moieties, alkynyl-(OH)-Br, macrocyclic poly(N-isopropylacrylamide) (c-PNIPAM) bearing a single hydroxyl functionality was prepared by atom transfer radical polymerization (ATRP), the subsequent end group transformation into azide functionality, and finally the intramacromolecular ring closure reaction via click chemistry. The target amphiphilic tadpole-shaped linear-cyclic diblock copolymer, (c-PNIPAM)-b-PCL, was then synthesized via the ROP of ε-caprolactone (CL) by directly initiating from the cyclic precursor. In aqueous solution at 20 °C, (c-PNIPAM)-b-PCL self-assembles into spherical micelles consisting of hydrophobic PCL cores and well-solvated coronas of cyclic PNIPAM segments. For comparison, linear diblock copolymer with comparable molecular weight and composition, (l-PNIPAM)-b-PCL, was also synthesized. It was found that the thermoresponsive coronas of micelles self-assembled from (c-PNIPAM)-b-PCL exhibit thermoinduced collapse and aggregation at a lower critical thermal phase transition temperature (T(c)) compared with those of (l-PNIPAM)-b-PCL. Temperature-dependent drug release profiles from the two types of micelles of (c-PNIPAM)-b-PCL and (l-PNIPAM)-b-PCL loaded with doxorubicin (Dox) were measured, and the underlying mechanism for the observed difference in releasing properties was proposed. Moreover, MTT assays revealed that micelles of (c-PNIPAM)-b-PCL are almost noncytotoxic up to a concentration of 1.0 g/L, whereas at the same polymer concentration, micelles loaded with Dox lead to ∼60% cell death. Overall, chain topologies of thermoresponsive block copolymers, that is, (c-PNIPAM)-b-PCL versus (l-PNIPAM)-b-PCL, play considerable effects on the self-assembling and thermal phase transition properties and their functions as controlled release drug nanocarriers.

Pathological Predictors for Site of Local Recurrence After Radiotherapy for Prostate Cancer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chopra, Supriya; Princess Margaret Hospital, University Health Network, Toronto; Toi, Ants

2012-03-01

Purpose: Rational design of targeted radiotherapy (RT) in prostate cancer (Pca) hinges on a better understanding of spatial patterns of recurrence. We sought to identify pathological factors predictive for site of local recurrence (LR) after external beam RT. Methods and Materials: Prospective databases were reviewed to identify men with LR after RT from 1997 through 2009. Patients with biochemical failure and biopsy-confirmed Pca more than 2 years after RT were evaluated. Prediction for site of recurrence based on the following pretreatment factors was determined on independent and cluster-sextant basis: presence of malignancy, dominant vs. nondominant percentage core length (PCL) involvement,more » PCL {>=} or <40%, and Gleason score. Sites of dominant PCL were defined as sextants with peak PCL involvement minus 10%, and >5% for each patient. Results: Forty-one patients with low-intermediate risk Pca constituted the study cohort. Median time to biopsy after RT was 51 months (range, 24-145). Of 246 sextants, 74 were involved with tumor at baseline. When sextants are treated as independent observations the presence of malignancy (77% vs. 22%, p = 0.0001), dominant PCL (90% vs. 46%, p = 0.0001), and PCL {>=}40% (89% vs. 68 %, p = 0.04) were found to be significant predictors for LR, although PCL {>=}40% did not retain statistical significance if sextants were considered correlated. The vast majority of patients (95%) recurred at the original site of dominant PCL or PCL {>=}40%, and 44% also recurred in regions of nondominant PCL <40% (n = 8) and/or benign sampling (n = 14) at baseline. Conclusions: LR after RT predominantly occurs in regions bearing higher histological tumor burden but are not isolated to these sites. Our data highlights the value of spatially resolved baseline pathological sampling and may assist in the design of clinical trials tailoring RT dose prescriptions to subregions of the prostate gland.« less

Superior anticancer efficacy of curcumin-loaded nanoparticles against lung cancer.

PubMed

Yin, Haitao; Zhang, Hao; Liu, Baorui

2013-08-01

Curcumin (CM) has anticancer potential for several cancers and blocks several steps in the carcinogenesis process. However, the clinical application of CM is greatly limited due to its low effects in vivo resulted from its poor solubility and pharmacokinetics. This raises the possibility of taking CM as a novel model drug in a new nanoparticle-based delivery system. In this study, CM-loaded nanoparticles were prepared from three kinds of amphilic methoxy poly(ethylene glycol) (mPEG)-polycaprolactone (PCL) block copolymers. It was noted that CM-loaded nanoparticles prepared from mPEG10k-PCL30k showed not only the highest loading efficiency, but also the most sustained release pattern. In vitro studies showed that CM was effectively transported into A549 cells by nanoparticles and localized around the nuclei in the cytoplasm. In addition, the cytotoxicity of CM-loaded nanoparticles with mEPG10k-PCL30k as a drug carrier was in a dose- and time-dependent manner in A549 cells. Further apoptotic staining results demonstrated the superior pro-apoptotic effect of CM-loaded nanoparticles over free drug. Data in this study not only confirmed the potential of CM in treating lung cancer, but also offered an effective way to improve the anticancer efficiency of CM through the nano-drug delivery system.

Conjugation of arginine-glycine-aspartic acid peptides to poly(ethylene oxide)-b-poly(epsilon-caprolactone) micelles for enhanced intracellular drug delivery to metastatic tumor cells.

PubMed

Xiong, Xiao-Bing; Mahmud, Abdullah; Uludağ, Hasan; Lavasanifar, Afsaneh

2007-03-01

An arginine-glycine-aspartic acid (RGD) containing model peptide was conjugated to the surface of poly(ethylene oxide)-block-poly(epsilon-caprolactone) (PEO-b-PCL) micelles as a ligand that can recognize adhesion molecules overexpressed on the surface of metastatic cancer cells, that is, integrins, and that can enhance the micellar delivery of encapsulated hydrophobic drug into a tumor cell. Toward this goal, PEO-b-PCL copolymers bearing acetal groups on the PEO end were synthesized, characterized, and assembled to polymeric micelles. The acetal group on the surface of the PEO-b-PCL micelles was converted to reactive aldehyde under acidic condition at room temperature. An RGD-containing linear peptide, GRGDS, was conjugated on the surface of the aldehyde-decorated PEO-b-PCL micelles by incubation at room temperature. A hydrophobic fluorescent probe, that is, DiI, was physically loaded in prepared polymeric micelles to imitate hydrophobic drugs loaded in micellar carrier. The cellular uptake of DiI loaded GRGDS-modified micelles by melanoma B16-F10 cells was investigated at 4 and 37 degrees C by fluorescent spectroscopy and confocal microscopy techniques and was compared to the uptake of DiI loaded valine-PEO-b-PCL micelles (as the irrelevant ligand decorated micelles) and free DiI. GRGDS conjugation to polymeric micelles significantly facilitated the cellular uptake of encapsulated hydrophobic DiI most probably by intergrin-mediated cell attachment and endocytosis. The results indicate that acetal-terminated PEO-b-PCL micelles are amenable for introducing targeting moieties on the surface of polymeric micelles and that RGD-peptide conjugated PEO-b-PCL micelles are promising ligand-targeted carriers for enhanced drug delivery to metastatic tumor cells.

MRI analysis of tibial PCL attachment in a large population of adult patients: reference data for anatomic PCL reconstruction.

PubMed

Teng, Yuanjun; Guo, Laiwei; Wu, Meng; Xu, Tianen; Zhao, Lianggong; Jiang, Jin; Sheng, Xiaoyun; Xu, Lihu; Zhang, Bo; Ding, Ning; Xia, Yayi

2016-09-05

Consistent reference data used for anatomic posterior cruciate ligament (PCL) reconstruction is not well defined. Quantitative guidelines defining the location of PCL attachment would aid in performing anatomic PCL reconstruction. The purpose was to characterize anatomic parameters of the PCL tibial attachment based on magnetic resonance imaging (MRI) in a large population of adult knees. The PCL tibial attachment site was examined in 736 adult knees with an intact PCL using 3.0-T proton density-weighted sagittal MRI. The outcomes measured were the anterior-posterior diameter (APD) of the tibial plateau; angle between the tibial plateau and the posterior tibial 'shelf' (the slope where the PCL tibial attachment site was) (PTS); length of the PTS; proximal, central, and distal PCL attachment positions as well as the width of the PCL attachment site; and vertical dimension of the PCL attachment site inferior from the tibial plateau. The average APD of the tibia plateau was 33.6 ± 3.5 mm, yielding significant differences between males (35.5 ± 3.0 mm) and females (31.6 ± 2.7 mm), P <.05, and there was a significantly decreasing trend with increasing age in males (P <.05). Mean angle between the tibial plateau and the PTS was 122.4° ± 8.1°, and subgroup analysis showed that the young group had a differently smaller angle (120.9° ± 7.5°) than the middle-aged (123.7° ± 8.2°) and the old (123.4° ± 7.7°) in males population, while there were no significant differences between sexes (P >.05). The proximal, central positions and width of the PCL attachment site were 13.4 ± 3.0 mm, 17.8 ± 3.0 mm and 9.6 ± 2.4 mm along the PTS, with significant differences between males and females (P <.05), and accounted for 60.0 % ± 9.1 %, 80.0 % ± 4.6 % and 43.3 % ± 9.7 % of the PTS respectively, with no significant differences between sexes and among age groups (all P >.05). This study provides reference data of the tibial PCL attachment based on MRI in the sagittal orientation. In analysis of retrospective data from a large population of adult patients, the quantitative values can be used as references to define the inserted angle and depth of the drill guide, and the exact position and size of the tibial PCL tunnel for performing arthroscopic anatomic PCL reconstruction.

Spontaneously self-assembled micelles from poly(ethylene glycol)-b-poly(epsilon-caprolactone-co-trimethylene carbonate) for drug solubilization.

PubMed

Latere, Dwan'Isa J P; Rouxhet, L; Brewster, M E; Préat, V; Ariën, A

2008-03-01

Di-block copolymers composed of polyethylene glycol (PEG) and a second block of (co)polyesters of epsilon-caprolactone (CL) and/or trimethylene carbonate (TMC) were synthesized and characterized. Tin octoate was used as catalyst and polymerization were completed over a period of 24 h with high conversion (> 95%). Self-assembling properties in water were evaluated. All di-block copolymers behave similarly except when PCL served as the second block. Stable crew-cut micelles of about 20 nm were obtained by direct dissolution of the liquid di-block copolymers in water at room temperature. When PCL was present as the second block, no solubilization occurred. Drug encapsulation of poorly water-soluble drugs belonging to biopharmaceutics classification system (BCS) class II (ketoprofen and furosemide) was evaluated. Experimental solubility for these two drugs shows a significant enhancement such that a maximum value of 23.4 mg/ml was obtained for ketoprofen in a 10% w/v micellar solution as compared to 0.14 mg in water. In the case of furosemide, the solubility increased from 0.04 mg/ml in water to about 3.2 mg/ml in a 10% w/v micellar solution. Enzymatic degradation of diblock copolymers was also studied in the presence of Pseudomonas lipase in a phosphate buffer solution (pH 7.4). Results indicated rapid degradation of copolymers containing relatively higher amounts of CL compared to TMC suggesting the potential in vivo degradation.

Surface modification of biodegradable porous Mg bone scaffold using polycaprolactone/bioactive glass composite.

PubMed

Yazdimamaghani, Mostafa; Razavi, Mehdi; Vashaee, Daryoosh; Tayebi, Lobat

2015-04-01

A reduction in the degradation rate of magnesium (Mg) and its alloys is in high demand to enable these materials to be used in orthopedic applications. For this purpose, in this paper, a biocompatible polymeric layer reinforced with a bioactive ceramic made of polycaprolactone (PCL) and bioactive glass (BG) was applied on the surface of Mg scaffolds using dip-coating technique under low vacuum. The results indicated that the PCL-BG coated Mg scaffolds exhibited noticeably enhanced bioactivity compared to the uncoated scaffold. Moreover, the mechanical integrity of the Mg scaffolds was improved using the PCL-BG coating on the surface. The stable barrier property of the coatings effectively delayed the degradation activity of Mg scaffold substrates. Moreover, the coatings induced the formation of apatite layer on their surface after immersion in the SBF, which can enhance the biological bone in-growth and block the microcracks and pore channels in the coatings, thus prolonging their protective effect. Furthermore, it was shown that a three times increase in the concentration of PCL-BG noticeably improved the characteristics of scaffolds including their degradation resistance and mechanical stability. Since bioactivity, degradation resistance and mechanical integrity of a bone substitute are the key factors for repairing and healing fractured bones, we suggest that PCL-BG is a suitable coating material for surface modification of Mg scaffolds. Published by Elsevier B.V.

Protein-resistant polymer coatings obtained by matrix assisted pulsed laser evaporation

NASA Astrophysics Data System (ADS)

Rusen, L.; Mustaciosu, C.; Mitu, B.; Filipescu, M.; Dinescu, M.; Dinca, V.

2013-08-01

Adsorption of proteins and polysaccharides is known to facilitate microbial attachment and subsequent formation of biofilm on surfaces that ultimately results in its biofouling. Therefore, protein repellent modified surfaces are necessary to block the irreversible attachment of microorganisms. Within this context, the feasibility of using the Poly(ethylene glycol)-block-poly(ɛ-caprolactone) methyl ether (PEG-block-PCL Me) copolymer as potential protein-resistant coating was explored in this work. The films were deposited using Matrix Assisted Pulsed Laser Evaporation (MAPLE), a technique that allows good control of composition, thickness and homogeneity. The chemical and morphological characteristics of the films were examined using Fourier Transform Infrared Spectroscopy (FTIR), contact angle measurements and Atomic Force Microscopy (AFM). The FTIR data demonstrates that the functional groups in the MAPLE-deposited films remain intact, especially for fluences below 0.5 J cm-2. Optical Microscopy and AFM images show that the homogeneity and the roughness of the coatings are related to both laser parameters (fluence, number of pulses) and target composition. Protein adsorption tests were performed on the PEG-block-PCL Me copolymer coated glass and on bare glass surface as a control. The results show that the presence of copolymer as coating significantly reduces the adsorption of proteins.

Tuning Structural Properties of Biocompatible Block Copolymer Micelles by Varying Solvent Composition

NASA Astrophysics Data System (ADS)

Cooksey, Tyler; Singh, Avantika; Mai Le, Kim; Wang, Shu; Kelley, Elizabeth; He, Lilin; Vajjala Kesava, Sameer; Gomez, Enrique; Kidd, Bryce; Madsen, Louis; Robertson, Megan

The self-assembly of block copolymers into micelles when introduced to selective solvents enables a wide array of applications, ranging from drug delivery to personal care products to nanoreactors. In order to probe the assembly and dynamics of micellar systems, the structural properties and solvent uptake of biocompatible poly(ethylene oxide-b- ɛ-caprolactone) (PEO-PCL) diblock copolymers in deuterated water (D2O) / tetrahydrofuran (THFd8) mixtures were investigated using small-angle neutron scattering in combination with nuclear magnetic resonance. PEO-PCL block copolymers, of varying molecular weight yet constant block ratio, formed spherical micelles through a wide range of solvent compositions. Varying the composition from 10 to 60 % by volume THFd8\\ in D2O / THFd8 mixtures was a means of varying the core-corona interfacial tension in the micelle system. An increase in THFd8 content in the bulk solvent increased the solvent uptake within the micelle core, which was comparable for the two series, irrespective of the polymer molecular weight. Differences in the behaviors of the micelle size parameters as the solvent composition varied originated from the differing trends in aggregation number for the two micelle series. Incorporation of the known unimer content determined from NMR allowed refinement of extracted micelle parameters.

Disulfiram-loaded mixed nanoparticles with high drug-loading and plasma stability by reducing the core crystallinity for intravenous delivery.

PubMed

Zhuo, Xuezhi; Lei, Tian; Miao, Linlin; Chu, Wei; Li, Xiaowen; Luo, Lifeng; Gou, Jingxin; Zhang, Yu; Yin, Tian; He, Haibing; Tang, Xing

2018-05-30

To develop an injectable formulation and improve the stability of disulfiram (DSF), DSF was encapsulated into mixed nanoparticles (DSF-NPs) through a high-pressure homogenization method. The Flory-Huggins interaction parameters (χ FH ) were calculated to predict the miscibility between DSF and the hydrophobic core, resulting in PCL 5000 selected as the hydrophobic block to encapsulate the DSF, as PCL 5000 had a lower χ FH 3.39 and the drug loading of the nanoparticles prepared by mPEG 5000 -PCL 5000 was relatively higher. mPEG 5000 -PCL 5000 and PCL 5000 were blended to reduce the leakage of DSF during preparation, as well as increase the stability of the nanoparticles. The cargo-loading capacity of the nanoparticles was improved from 3.35% to 5.50% by reducing the crystallinity of the PCL nanoparticle core, and the crystallinity decreased from 51.13% to 25.15% after adding medium chain triglyceride (MCT). The DSF-NPs prepared by the above method had a small particle size of 98.1 ± 10.54 nm, with a polydispersity index (PDI) of 0.036, as well as drug loading of 5.50%. Furthermore, DSF-NPs containing MCT showed higher stability than DSF-NPs without MCT and DSF-sol (DSF dissolved in Cremophor EL and ethanol) in water and 90% plasma-containing PBS. The pharmacokinetics proved that DSF-NPs containing MCT enhanced the DSF concentration in the blood. Finally, DSF-NPs effectively inhibited H22 xenograft tumor growth in vivo. Copyright © 2018 Elsevier Inc. All rights reserved.

Electric field stimulation through a biodegradable polypyrrole-co-polycaprolactone substrate enhances neural cell growth

PubMed Central

Nguyen, Hieu T; Wei, Claudia; Chow, Jacqueline K; Nguyen, Alvin; Coursen, Jeff; Sapp, Shawn; Luebben, Silvia; Chang, Emily; Ross, Robert; Schmidt, Christine E

2014-01-01

Nerve guidance conduits (NGCs) are FDA-approved devices used to bridge gaps across severed nerve cables and help direct axons sprouting from the proximal end toward the distal stump. In this paper we present the development of a novel electrically conductive, biodegradable NGC made from a polypyrrole-block-polycaprolactone (PPy-PCL) copolymer material laminated with poly(lactic-co-glycolic acid) (PLGA). The PPy-PCL has a bulk conductivity ranging 10–20 S/cm and loses 40 wt% after 7 months under physiologic conditions. Dorsal root ganglia (DRG) grown on flat PPy-PCL/PLGA material exposed to direct current electric fields (EF) of 100 mV/cm for 2 h increased axon growth by 13% (± 2%) towards either electrode of a 2-electrode setup, compared to control grown on identical substrates without EF exposure. Alternating current increased axon growth by 21% (± 3%) without an observable directional preference, compared to the same control group. The results from this study demonstrate PLGA-coated PPy-PCL is a unique biodegradable material that can deliver substrate EF stimulation to improve axon growth for peripheral nerve repair. PMID:23964001

Effect of Stellate Ganglion Block on Specific Symptom Clusters for Treatment of Post-Traumatic Stress Disorder.

PubMed

Lynch, James H; Mulvaney, Sean W; Kim, Eugene H; de Leeuw, Jason B; Schroeder, Matthew J; Kane, Shawn F

2016-09-01

This study assessed which symptoms are most impacted following stellate ganglion block (SGB) used to treat post-traumatic stress disorder (PTSD) symptoms. 30 active military service members with combat-related PTSD self-referred to their physician and psychologist. Patients were offered a SGB as part of their treatment program. Primary outcome was the magnitude of change for the 17 items on the PTSD Checklist-Military (PCL-M), which was administered the week before SGB, 1 week after SGB, and 2 to 4 months later. Mean PCL-M score decreased from 49 at baseline to 32, 1 week after the procedure (p < 0.001). 2 to 4 months after SGB, patients maintained an average PCL-M of 32. Patients reported greatest improvement in the first week after SGB for the following symptoms: irritability or angry outbursts, difficulty concentrating, and sleep disturbance. 2 to 4 months later, patients reported greatest improvement in the following: feeling distant or cut off, feeling emotionally numb, irritability or angry outbursts, and difficulty concentrating. SGB is a safe procedure that may provide extended relief for all clusters of PTSD symptoms. As a result of the significant reduction in hyperarousal and avoidance symptoms observed, this study supports incorporation of SGB into PTSD treatment plans. Reprint & Copyright © 2016 Association of Military Surgeons of the U.S.

Nanoporous capsules of block co-polymers of [(MeO-PEG-NH)-b-(L-GluA)]-PCL for the controlled release of anticancer drugs for therapeutic applications.

PubMed

Amgoth, Chander; Dharmapuri, Gangappa; Kalle, Arunasree M; Paik, Pradip

2016-03-29

Herein, new nanoporous capsules of the block co-polymers of MeO-PEG-NH-(L-GluA)10 and polycaprolactone (PCL) have been synthesized through a surfactant-free cost-effective self-assembled soft-templating approach for the controlled release of drugs and for therapeutic applications. The nanoporous polymer capsules are designed to be biocompatible and are capable of encapsulating anticancer drugs (e.g., doxorubicin hydrochloride (DOX) and imatinib mesylate (ITM)) with a high extent (∼279 and ∼480 ng μg(-1), respectively). We have developed a nanoformulation of porous MeO-PEG-NH-(L-GluA)10-PCL capsules with DOX and ITM. The porous polymer nanoformulations have been programmed in terms of the release of anticancer drugs with a desired dose to treat the leukemia (K562) and human carcinoma cells (HepG2) in vitro and show promising IC50 values with a very high mortality of cancer cells (up to ∼96.6%). Our nanoformulation arrests the cell divisions due to 'cellular scenescence' and kills the cancer cells specifically. The present findings could enrich the effectiveness of idiosyncratic nanoporous polymer capsules for use in various other nanomedicinal and biomedical applications, such as for killing cancer cells, immune therapy, and gene delivery.

Nanoporous capsules of block co-polymers of [(MeO-PEG-NH)-b-(L-GluA)]-PCL for the controlled release of anticancer drugs for therapeutic applications

NASA Astrophysics Data System (ADS)

Amgoth, Chander; Dharmapuri, Gangappa; Kalle, Arunasree M.; Paik, Pradip

2016-03-01

Herein, new nanoporous capsules of the block co-polymers of MeO-PEG-NH-(L-GluA)10 and polycaprolactone (PCL) have been synthesized through a surfactant-free cost-effective self-assembled soft-templating approach for the controlled release of drugs and for therapeutic applications. The nanoporous polymer capsules are designed to be biocompatible and are capable of encapsulating anticancer drugs (e.g., doxorubicin hydrochloride (DOX) and imatinib mesylate (ITM)) with a high extent (˜279 and ˜480 ng μg-1, respectively). We have developed a nanoformulation of porous MeO-PEG-NH-(L-GluA)10-PCL capsules with DOX and ITM. The porous polymer nanoformulations have been programmed in terms of the release of anticancer drugs with a desired dose to treat the leukemia (K562) and human carcinoma cells (HepG2) in vitro and show promising IC50 values with a very high mortality of cancer cells (up to ˜96.6%). Our nanoformulation arrests the cell divisions due to ‘cellular scenescence’ and kills the cancer cells specifically. The present findings could enrich the effectiveness of idiosyncratic nanoporous polymer capsules for use in various other nanomedicinal and biomedical applications, such as for killing cancer cells, immune therapy, and gene delivery.

Synthesis, characterization, and property of biodegradable PEG-PCL-PLA terpolymers with miktoarm star and triblock architectures as drug carriers.

PubMed

Zhang, Yixin; Luo, Song; Liang, Yan; Zhang, Hai; Peng, Xinyu; He, Bin; Li, Sai

2018-03-01

A series of amphiphilic terpolymers with miktoarm star and triblock architectures of poly(ethylene glycol) (PEG), poly(ε-caprolactone) (PCL) and poly(l-lactide acid) (PLLA) or poly(DL-lactide acid) (PDLLA) terpolymers were synthesized as carriers for drug delivery. The architecture, molecular weight and crystallization behavior of the terpolymers were characterized. Anticancer drug doxorubicin was encapsulated in the micelles to investigate their drug loading properties. The miktoarm star terpolymers exhibited stronger crystallization capability, smaller size and better stability than that of triblock polymeric micelle, owing to the lower CMC values of miktoarm star polymeric micelle. Furthermore, the drug-loaded miktoarm star polymeric micelles showed the cumulative DOX release account of the micelles with PDLLA blocks was 65.3% while the release account of the corresponding micelles containing PLLA blocks was 45.2%. The IC 50 values of drug-loaded miktoarm star polymeric micelle were lower than triblock polymeric micelle. Meanwhile, Confocal laser scanning microscopy (CLSM) and Flow Cytometry results demonstrated that the miktoarm star micelles were more favorable for cellular internalization. The miktoarm star micelles with PDLLA blocks were promising carriers for anticancer drug delivery.

Self-aggregation of cationically modified poly(ε-caprolactone)2-co-poly(ethylene glycol) copolymers: Effect of cationic grafting ligand and poly(ε-caprolactone) chain length.

PubMed

Charoongchit, Pimchanok; Suksiriworapong, Jiraphong; Sripha, Kittisak; Mao, Shirui; Sapin-Minet, Anne; Maincent, Philippe; Junyaprasert, Varaporn Buraphacheep

2017-03-01

Cationic copolymers have been attractive to investigate due to their potential to complexation with anionic drugs and expected to use in the pharmaceutical application. In this study, the modified poly(ε-caprolactone) 2 -co-poly(ethylene glycol) copolymers (P(CL) 2 -PEG) were successfully synthesized by click reaction. The amount of small molecular cationic ligand, propargyltrimethyl ammonium iodide, was varied and grafted onto various mole ratios of P(CL) to PEG. The effects of P(CL) chain length and amount of the grafting cationic ligand on physicochemical properties of polymers and particles were studied. The number-average molecular weights of the copolymers grafted with cationic ligand were found ranging between 10,000 and 23,000g/mol as investigated by NMR. From DSC study, the results showed that the grafting ligand affected thermal behaviors of the copolymers by increasing the glass transition temperature and decreasing the melting temperature of the copolymers. Furthermore, these cationic copolymers could self-aggregate with their critical aggregation concentration depending on mole ratios of hydrophilic to hydrophobic portions. The particles containing higher amounts of the cationic ligand tended to aggregate in both acidic and basic pH environment and at high salt concentration. Additionally, particle size, size distribution (PdI), and morphology of self-assembling particles varied depending on P(CL) chain length and the amount of the grafting cationic ligand. The synthesized cationic copolymer showed a capability to encapsulate a high negatively charged drug, enoxaparin, with an encapsulation efficiency of 87%. After drug incorporation, the particles substantially changed in size, shape, PdI, and zeta potential to become more suitable for drug delivery. These cationic copolymers with flexible properties will be the candidate for further development as carriers for the delivery of negatively charged drugs. Copyright © 2016. Published by Elsevier B.V.

Adhesion of mesenchymal stem cells to polymer scaffolds occurs via distinct ECM ligands and controls their osteogenic differentiation.

PubMed

Chastain, Sara R; Kundu, Anup K; Dhar, Sanjay; Calvert, Jay W; Putnam, Andrew J

2006-07-01

The osteogenic potential of mesenchymal stem cells (MSCs) cultured on poly(lactide-co-glycolide) (PLGA) or poly(caprolactone) (PCL), two widely used polymeric biomaterials that have been reported to differentially support osteogenic differentiation, was compared in these studies. Here we report that MSCs cultured in 3-D PLGA scaffolds for up to 5 weeks significantly upregulate osteocalcin gene expression levels. By contrast, osteocalcin expression was markedly downregulated in 3-D PCL-based constructs over the same time course. We hypothesized that differential adsorption of extracellular matrix (ECM) proteins present in serum-containing culture medium and subsequent differences in integrin-mediated adhesion are responsible for these differences, and tested this hypothesis using thin (2-D) polymeric films. Supporting this hypothesis, significant amounts of fibronectin and vitronectin deposited onto both materials in serum-containing osteogenic media, with type-I collagen present in lower amounts. Adhesion-blocking studies revealed that MSCs adhere to PCL primarily via vitronectin, while type-I collagen mediates their attachment to PLGA. These adhesive mechanisms correlated with higher levels of alkaline phosphatase (ALP) activity after 2 weeks of monolayer culture on PLGA versus PCL. These data suggest that the initial adhesion of MSCs to PLGA via type-I collagen fosters osteogenesis while adhesion to PCL via vitronectin does not, and stress the need for an improved molecular understanding of cell-ECM interactions in stem cell-based therapies. Copyright (c) 2006 Wiley Periodicals, Inc.

Biodegradable shape-memory block co-polymers for fast self-expandable stents.

PubMed

Xue, Liang; Dai, Shiyao; Li, Zhi

2010-11-01

Block co-polymers PCTBVs (M(n) of 36,300-65,300 g/mol, T(m) of 39-40 and 142 degrees C) containing hyperbranched three-arm poly(epsilon-caprolactone) (PCL) as switching segment and microbial polyester PHBV as crystallizable hard segment were designed as biodegradable shape-memory polymer (SMP) for fast self-expandable stent and synthesized in 96% yield by the reaction of three-arm PCL-triol (M(n) of 4200 g/mol, T(m) of 47 degrees C) with methylene diphenyl 4,4'-diisocyanate isocynate (MDI) to form the hyperbrached MDI-linked PCL (PTCM; M(n) of 25,400 g/mol and a T(m) of 38 degrees C), followed by further polymerization with PHBV-diol (M(n) of 2200 g/mol, T(m) of 137 and 148 degrees C). The polymers were characterized by (1)H NMR, GPC, DSC, tensile test, and cyclic thermomechanical tensile test. PCTBVs showed desired thermal properties, mechanical properties, and ductile nature. PCTBV containing 25 wt% PHBV (PCTBV-25) demonstrated excellent shape-memory property at 40 degrees C, with R(f) of 94%, R(r) of 98%, and shape recovery within 25s. PCTBV-25 was also shown as a safe material with good biocompatibility by cytotoxicity tests and cell growth experiments. The stent made from PCTBV-25 film showed nearly complete self-expansion at 37 degrees C within only 25 s, which is much better and faster than the best known self-expandable stents. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Surface chemistry of PH 3, PF 3 and PCl 3 on Ru(0001)

NASA Astrophysics Data System (ADS)

Tao, H.-S.; Diebold, U.; Shinn, N. D.; Madey, T. E.

1994-06-01

The adsorption, desorption and decomposition of PH 3, PF 3 and PCl 3 on Ru(0001) have been studied by soft X-ray photoelectron spectroscopy (SXPS) using synchrotron radiation. Due to large chemical shifts in the P 2p core levels, different phosphorus containing surface species can be identified. We find that PF 3 adsorbs molecularly on Ru(0001) at 80 and 300 K. At 80 K, PH 3 saturates the surface with one layer of atomic hydrogen, elemental phosphorus, subhydride (i.e., PHx (0 < x < 3)) and PH 3, with a total phosphorus coverage of 0.4 ML. At 300 K, PH 3 decomposes into atomic hydrogen and elemental phosphorus with a phosphorus coverage of 0.8 ML. At 80 K, PCl 3 adsorbs dissociatively into atomic chlorine, elemental phosphorus, PCl and possibly PCl 2 and PCl 3 in the first monolayer. Formation of multilayers of PCl 3 is observed at 80 K. At 300 K, PCl 3 adsorbs dissociatively as atomic chlorine and elemental phosphorus with a saturation phosphorus coverage of 0.1 ML. The variation in total phosphorus uptake at 300 K from PX3 ( X = H, FandCl) adsorption is a result of competition between site blocking by dissociation fragments and displacement reactions. Annealing surfaces with adsorbed phosphorus to 1000 K results in formation of RuzP ( z = 1 or 2), which is manifested by the chemical shifts in the P2p core level, as well as the P LVV Auger transition. The recombination of adsorbed phosphorus and adsorbed X ( = H, FandCl) from decomposition is also observed, but is a minor reaction channel on the surface. Thermochemical data are used to analyze the different stabilities of PX 3 at 300 K, namely, PF 3 adsorbs molecularly and PH 3 and PCl 3 dissociate completely. First, we compare the heat of molecular adsorption and the heat of dissociative adsorption of PX 3 on Ru(0001), using an enthalpy approach, and find results consistent with experimental observations. Second, we compare the total bond energy difference between molecular adsorption and complete dissociation of PX 3 on Ru(0001). In particular, we apply Shustorovich's bond-order conservation-Morse potential (BOC-MP) method to estimate the heat of adsorption for PH 3 and PCl 3 and the bond energies of the relaxed P-X bonds of the adsorbed PX 3 on the surface. The bond strength difference among the relaxed P-X bonds (i.e., the relaxed P-F bond ( 475 {kJ}/{mol}) is much stronger than either the relaxed P-H bond ( 287 {kJ}/{mol}) or the relaxed P-Cl bond ( 288 {kJ}/{mol})) suggests that PF 3 is more stable than PH 3 and PCl 3 on Ru(0001) at 300 K. These values are used to evaluate the total bond energy differences between molecular adsorption and complete dissociation for each of the PX 3, and the results agree with the experimental trends.

Kinematic and kinetic analysis of the knee joint before and after a PCL retaining total knee replacement during gait and single step ascent.

PubMed

Apostolopoulos, Alexandros; Lallos, Stergios; Mastrokalos, Dimitrios; Michos, Ioannis; Darras, Nikolaos; Tzomaki, Magda; Efstathopoulos, Nikolaos

2011-01-01

The objective of this study was to capture and analyze the kinetics and kinematics and determine the functional performance of the osteoarthritic knee after a posterior cruciate ligament (PCL) retaining total knee arthroplasty. Kinematic and kinetic gait analysis of level walking was performed in 20 subjects (12 female and 8 male) with knee ostoarthritis. These patients were free of any neurological diseases that could affect their normal gait. Mean age was 69.6 ± 6.6 years; mean height was 157.6 cm ± 7.6 cm; and mean weight was 77.2 ± 12.1 kg. Full body gait analyses were performed using the BIOKIN 3D motion analysis system before and 9 months after total knee arthroplasty procedures. Single-step ascending kinetic analyses and plantar pressure distribution analyses were also performed for all subjects. International Knee Society Scores (IKSSs) were also assessed pre- and postoperatively. Significant increases were noted postoperatively in average cadence (preoperative mean = 99.26, postoperative mean = 110.5; p < 0.004), step length (preoperative mean = 0.49, postoperative mean = 0.54; p < 0.01) , and walking velocity (preoperative mean = 0.78, preoperatively, postoperative mean = 0.99; p < 0.001). Decreases in stance duration percentage and knee adduction moment were also reported postoperatively. All patients showed a significant improvement of knee kinetics and kinematics after a PCL retaining total knee arthroplasty. Significant differences were found in the cadence, step length, stride length, and walk velocity postoperatively. IKSSs also significantly improved. Further research is warranted to determine the clinical relevance of these findings.

Novel self-associating poly(ethylene oxide)-b-poly(epsilon-caprolactone) based drug conjugates and nano-containers for paclitaxel delivery.

PubMed

Shahin, Mostafa; Lavasanifar, Afsaneh

2010-04-15

Poly(ethylene oxide)-block-poly(epsilon-caprolactone) (PEO-b-PCL) copolymers bearing paclitaxel (PTX) side groups on PCL (PEO-b-P(CL-PTX) were synthesized and assembled to particles of 123 nm average diameter. At 20% (w/w) PTX to polymer conjugation, PEO-b-P(CL-PTX) demonstrated only 5.0 and 6.7% PTX release after 72 h incubation at pH 7.4 and 5.0, respectively, but revealed signs of chain cleavage at pH 5.0. The cytotoxicity of PEO-b-P(CL-PTX) against MDA-MB-435 cancer cells increased as incubation time was raised from 72 to 96 h (IC(50) of 680 and 475 ng/mL, respectively), but it was still significantly lower than the cytotoxicity of free PTX (IC(50) of 3.5 ng/mL at 72 h). In further studies, micelles of PEO-b-PCL and those bearing benzyl or PTX on PCL were used for physical encapsulation of PTX, where maximum level of loading was achieved by PEO-b-P(CL-PTX) (2.22%, w/w). The release of PTX from this carrier was rapid; however. The in vitro cytotoxicity of physically loaded PTX was independent of carrier and similar to that of free PTX. This was attributed to the low concentration of polymers which fell below their critical micellar concentration in the cytotoxicity study. The results point to the potential of chemically tailored PEO-b-PCL for optimum PTX solubilization and delivery. Copyright 2010 Elsevier B.V. All rights reserved.

The effect of the hydrophilic/hydrophobic ratio of polymeric micelles on their endocytosis pathways into cells.

PubMed

Zhang, Zhao; Qu, Qianqian; Li, Jinrong; Zhou, Shaobing

2013-06-01

Fluorescein isothiocyanate (FITC), a fluorescent probe, is coupled to amphiphilic monomethoxy poly(ethylene glycol)-block-poly(ε-caprolactone) (mPEG-PCL) copolymers. FITC-labeled mPEG-PCL copolymers self-assemble into micelles through the solvent evaporation method. The cellular internalization is examined using fluorescence microscopy on incubation of NIH-3T3 fibroblasts with micelles or free FITC solution. The effect of the hydrophilic/hydrophobic ratio on the endocytosis mechanisms is evaluated by fluorescence microscopy on culturing of human hepatoblastoma cells and human umbilical vein endothelial cells, individually, mixed with the micelles holding the same parameters including micelle size, shape, and surface charges. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Biodegradable hyperbranched amphiphilic polyurethane multiblock copolymers consisting of poly(propylene glycol), poly(ethylene glycol), and polycaprolactone as in situ thermogels.

PubMed

Li, Zibiao; Zhang, Zhongxing; Liu, Kerh Li; Ni, Xiping; Li, Jun

2012-12-10

This paper reports the synthesis and characterization of new hyperbranched amphiphilic polyurethane multiblock copolymers consisting of poly(propylene glycol) (PPG), poly(ethylene glycol) (PEG), and polycaprolactone (PCL) segments as in situ thermogels. The hyperbranched poly(PPG/PEG/PCL urethane)s, termed as HBPEC copolymers, were synthesized from PPG-diol, PEG-diol, and PCL-triol by using 1,6-hexamethylene diisocyanate (HMDI) as a coupling agent. The compositions and structures of HBPEC copolymers were determined by GPC and 1H NMR spectroscopy. We carried out comparative studies of the new hyperbranched copolymers with their linear counterparts, the linear poly(PPG/PEG/PCL urethane) (LPEC) copolymer and Pluronic F127 PEG-PPG-PEG block copolymer, in terms of their self-assembly and aggregation behaviors and thermoresponsive properties. HBPEC copolymers were found to show thermoresponsive micelle formation and aggregation behaviors. Particularly, the lower critical solution temperature (LCST) of the copolymers was significantly affected by the copolymer architecture. HBPEC copolymers showed much lower LCST than LPEC, the linear counterpart. Our studies revealed that the effect of hyperbranch architecture was more prominent in the gelation of the copolymers. The aqueous solutions of HBPEC copolymers exhibited thermogelling behaviors at critical gelation concentrations (CGCs) ranging from 4.3 to 7.4 wt %. These values are much lower than those reported on other PCL-contained linear thermogelling copolymers and Pluronic F127 copolymer. In addition, the CGC of HBPEC copolymers is much lower than the control LPEC copolymer. More interestingly, at high temperatures, while LPEC and other linear thermogelling copolymers formed turbid sol, HBPEC formed a dehydrated gel. Our data suggest that these phenomena are caused by the hyperbranched structure of HBPEC copolymers, which could increase the interaction of copolymer branches and enhance the chain association through synergetic hydrogen bonding effect. The thermogelling behavior of HBPEC block copolymers was further evidenced by the 1H NMR molecular dynamic study and rheological study, which further support the above hypothesis. The hydrolytic degradation study showed that the HBPEC copolymer hydrogels are biodegradable under physiological conditions. Together with the good cell biocompatibility demonstrated by the cytotoxicity study, the new thermogelling copolymers reported in this paper could potentially be used as in situ-forming hydrogels for biomedical applications.

A thermosensitive hydrogel based on biodegradable amphiphilic poly(ethylene glycol) polycaprolactone poly(ethylene glycol) block copolymers

NASA Astrophysics Data System (ADS)

Gong, Chang Yang; Qian, Zhi Yong; Liu, Cai Bing; Juan Huang, Mei; Gu, Ying Chun; Wen, Yan Jun; Kan, Bing; Wang, Ke; Dai, Mei; Li, Xing Yi; Gou, Ma Ling; Tu, Ming Jing; Wei, Yu Quan

2007-06-01

A series of low molecular weight poly(ethylene glycol)-polycaprolactone-poly(ethylene glycol) (PEG-PCL-PEG) biodegradable block copolymers were successfully synthesized using isophorone diisocyanate (IPDI) as the coupling agent, and were characterized using 1H NMR and Fourier transform infrared spectroscopy. The aqueous solutions of the PEG-PCL-PEG copolymers displayed a special thermosensitive gel-sol transition when the concentration was above the corresponding critical gel concentration. Gel-sol phase diagrams were recorded using the test-tube-inversion method; they depended on the hydrophilic/hydrophobic balance in the macromolecular structure, as well as some other factors, including the heating history, volume, and the ageing time of the copolymer aqueous solutions and dissolution temperature of the copolymers. As a result, the gel-sol transition temperature range could be altered, which might be very useful for application in injectable drug delivery systems. This work was financially supported by the Chinese Key Basic Research Program (2004CB518800 and 2004CB518807), and the Sichuan Key Project of Science and Technology (06(05SG022-021-02)).

Novel docetaxel-loaded nanoparticles based on poly(lactide-co-caprolactone) and poly(lactide-co-glycolide-co-caprolactone) for prostate cancer treatment: formulation, characterization, and cytotoxicity studies

NASA Astrophysics Data System (ADS)

Sanna, Vanna; Roggio, Anna Maria; Posadino, Anna Maria; Cossu, Annalisa; Marceddu, Salvatore; Mariani, Alberto; Alzari, Valeria; Uzzau, Sergio; Pintus, Gianfranco; Sechi, Mario

2011-12-01

Docetaxel (Dtx) chemotherapy is the optional treatment in patients with hormone-refractory metastatic prostate cancer, and Dtx-loaded polymeric nanoparticles (NPs) have the potential to induce durable clinical responses. However, alternative formulations are needed to overcome the serious side effects, also due to the adjuvant used, and to improve the clinical efficacy of the drug. In the present study, two novel biodegradable block-copolymers, poly(lactide-co-caprolactone) (PLA-PCL) and poly(lactide-co-caprolactone-co-glycolide) (PLGA-PCL), were explored for the formulation of Dtx-loaded NPs and compared with PLA- and PLGA-NPs. The nanosystems were prepared by an original nanoprecipitation method, using Pluronic F-127 as surfactant agent, and were characterized in terms of morphology, size distribution, encapsulation efficiency, crystalline structure, and in vitro release. To evaluate the potential anticancer efficacy of a nanoparticulate system, in vitro cytotoxicity studies on human prostate cancer cell line (PC3) were carried out. NPs were found to be of spherical shape with an average diameter in the range of 100 to 200 nm and a unimodal particle size distribution. Dtx was incorporated into the PLGA-PCL NPs with higher ( p < 0.05) encapsulation efficiency than that of other polymers. Differential scanning calorimetry suggested that Dtx was molecularly dispersed in the polymeric matrices. In vitro drug release study showed that release profiles of Dtx varied on the bases of characteristics of polymers used for formulation. PLA-PCL and PLGA-PCL drug loaded NPs shared an overlapping release profiles, and are able to release about 90% of drug within 6 h, when compared with PLA- and PLGA-NPs. Moreover, cytotoxicity studies demonstrated advantages of the Dtx-loaded PLGA-PCL NPs over pure Dtx in both time- and concentration-dependent manner. In particular, an increase of 20% of PC3 growth inhibition was determined by PLGA-PCL NPs with respect to free drug after 72 h incubation and at all tested Dtx concentration. In summary, PLGA-PCL copolymer may be considered as an attractive and promising polymeric material for the formulation of Dtx NPs as delivery system for prostate cancer treatment, and can also be pursued as a validated system in a more large context.

Obliteration of Intercondylar Notch Mimicking Flexion-Extension Gap Imbalance in a Cruciate Retaining Total Knee Arthroplasty

PubMed Central

Gungor, Harun Resit; Kiter, Esat; Akkaya, Semih; Ok, Nusret; Yorukoglu, Cagdas

2015-01-01

Following total knee arthroplasty (TKA), the most frequent cause of extension deficit and limitation of range of motion in early postoperative period is related to improper tensioning of soft tissues and failure to balance extension and flexion gaps. If a cruciate retaining (CR) prosthesis is the planned implant, then attention should be given to balancing the posterior cruciate ligament (PCL), and any factor that alters this balance may also cause deterioration of knee balance in postoperative period. Here, we report on an unusual case referred from another hospital because of continuous pain and restriction of knee motion in early postoperative period following CR-designed TKA that was initially thought to be due to flexion-extension imbalance. However, during the revision procedure, extruded cement to the intercondylar notch was found to be both mechanically blocking terminal extension and limiting flexion by possible mechanism of irritation of the synovial nerve endings around the stretched anterior fibers of PCL during flexion. This case was successfully treated by removal of extruded cement from intercondylar notch to decompress PCL, polyethylene exchange, and secondary patellar resurfacing. PMID:26185697

α-Lipoic acid stabilized DTX/IR780 micelles for photoacoustic/fluorescence imaging guided photothermal therapy/chemotherapy of breast cancer.

PubMed

Li, WenTing; Peng, JinRong; Yang, Qian; Chen, LiJuan; Zhang, Lan; Chen, XiaoXin; Qian, ZhiYong

2018-05-01

Micellar nanoparticles have unique advantages as carriers for therapeutic or imaging agents, owing to their smaller size and better penetration of tumors. However, some agents, due to their physical or chemical properties, are difficult to load into micelles. IR780 is one of these agents, and is also a promising near-infrared dye for fluorescence imaging (FI)/photoacoustic imaging (PAI) and cancer photothermal therapy (PTT). Its hydrophobic and high crystallization structure results in limited bioavailability in vivo. It is difficult to load into micelles constructed from an amphiphilic block polymer with relatively low molecular weight. In this study, we use computer simulation and introduce another small biomolecule, α-lipoic acid, into the micelles constructed from a mPEG-PCL copolymer, to lower the energy of molecular interaction between MPEG-PCL and IR780, and expect to enhance the loading capacity of the micelles to IR780. The introduction of α-lipoic acid decreases the energy of molecular interaction between MEPG-PCL and IR780 from -46.18 kJ mol-1 to -196.52 kJ mol-1 and increases the loading capacity and stability of the mPEG-PCL micelles to IR780, which also maintains the loading capacity to DTX. We further construct DTX/IR780 co-loaded mPEG-PCL micelles for FI/PAI dual modal imaging guided PTT/chemotherapy of cancer. By FI and PAI evaluation in vitro and in vivo, we demonstrate that the DTX/IR780 co-loaded micelles can be used as FI and PAI probes. By further evaluating the therapeutic outcome of PTT/chemotherapy co-therapy of breast cancer, we demonstrate that the DTX/IR780 co-loaded mPEG-PCL micelles can serve as promising candidates for FI and PAI guided PTT/chemotherapy of breast cancer.

Polymeric micelles for parenteral delivery of sagopilone: physicochemical characterization, novel formulation approaches and their toxicity assessment in vitro as well as in vivo.

PubMed

Richter, Annett; Olbrich, Carsten; Krause, Michael; Hoffmann, Jens; Kissel, Thomas

2010-06-01

The block copolymers PEG(2000)-b-PLA(2200), PEG(2000)-b-PCL(2600) and PEG(5000)-b-PCL(5000) have been currently identified as optimal solubilizing agents for Sagopilone, a poorly water-soluble anticancer drug. In the present study, the stability, formulation feasibility and in vitro as well as in vivo toxicity were evaluated. Dispersion media, storage conditions, and dilutions were varied for stability assessment. The critical micelle concentration (CMC) was determined using a fluorescent probe technique. Lyophilizates and polymeric films were investigated as formulation options. Furthermore, the toxicity was studied in vitro and in vivo using HeLa/MaTu cells and a nude mouse model, respectively. A drug-polymer ratio as low as 1:20 (w/w) was sufficient to solubilize Sagopilone effectively and to obtain stable dispersions (24h: drug content >or= 95%). Although the micelles exhibited a similar thermodynamic stability (CMC: 10(-7)-10(-6)M), PEG-b-PCL micelles were kinetically more stable than PEG(2000)-b-PLA(2200) (24h at 37 degrees C: drug content >or= 90% compared to 30%, respectively). Lyophilization of PEG-b-PCL micelles and storage stability of solid drug-loaded PEG(2000)-b-PLA(2200) films (3m, 6 degrees C: drug content of (95.6+/-1.4)%) were demonstrated for the first time. The high antiproliferative activity has been maintained in vitro (IC(50)<1 nM). Carrier-associated side effects have not been observed in vivo and the maximum tolerated dose of micellar Sagopilone was determined to be 6 mg/kg. The results of this study indicate that polymeric micelles, especially PEG-b-PCL micelles, offer excellent potential for further preclinical and clinical cancer studies using Sagopilone. Copyright 2010 Elsevier B.V. All rights reserved.

Scalability of an endoluminal spring for distraction enterogenesis.

PubMed

Rouch, Joshua D; Huynh, Nhan; Scott, Andrew; Chiang, Elvin; Wu, Benjamin M; Shekherdimian, Shant; Dunn, James C Y

2016-12-01

Techniques of distraction enterogenesis have been explored to provide increased intestinal length to treat short bowel syndrome (SBS). Self-expanding, polycaprolactone (PCL) springs have been shown to lengthen bowel in small animal models. Their feasibility in larger animal models is a critical step before clinical use. Juvenile mini-Yucatan pigs underwent jejunal isolation or blind ending Roux-en-y jejunojejunostomy with insertion of either a PCL spring or a sham PCL tube. Extrapolated from our spring characteristics in rodents, proportional increases in spring constant and size were made for porcine intestine. Jejunal segments with 7mm springs with k between 9 and 15N/m demonstrated significantly increased lengthening in isolated segment and Roux-en-y models. Complications were noted in only two animals, both using high spring constant k>17N/m. Histologically, lengthened segments in the isolated and Roux models demonstrated significantly increased muscularis thickness and crypt depth. Restoration of lengthened, isolated segments back into continuity was technically feasible after 6weeks. Self-expanding, endoluminal PCL springs, which exert up to 0.6N force, safely achieve significant intestinal lengthening in a translatable, large-animal model. These spring characteristics may provide a scalable model for the treatment of SBS in children. Copyright © 2016 Elsevier Inc. All rights reserved.

[Emotional processing in patients with a dissocial personality disorder subtype "psychopathy" according to PCL-R].

PubMed

Weber, Tatjana; Sommer, Monika; Hajak, Göran; Müller, Jürgen

2004-11-01

Functional MRI was used to test the effects of the deficient emotional responsiveness of psychopathic patients on cognitive processes. We used a Simon-paradigm, in which ten healthy volunteers and ten patients with a diagnosis of "psychopathy" (defined by Hare Psychopathy Checklist Revised) have to select their spatially defined responses on the basis of a nonspatial stimuli feature. For the emotion induction pictures from the International Affective Picture System (IAPS) were selected. At the beginning and intermediated by the Simon-paradigm blocks of positive, negative or neutral pictures were presented. Patients with "psychopathy" exhibited untypical activation patterns in amygdala and prefrontal regions during interferences between negative or positive stimulations and cognitive tasks. These results demonstrated disturbed regulation of emotion-cognition-interaction in "psychopathy" according to PCL-R.

Biotic - Abiotic Interface Between they Body and the Artificial Limb

DTIC Science & Technology

2008-09-29

transcutaneous amputation prosthesis ; machining; osseointegration; polycaprolactone; surface roughness; tensile strength; tissue adhesion; tissue...centrifuge at 2000 rpm for 5 minutes to remove air bubbles. This solution was then used for scaffold printing. Printing PCL Scaffolds The syringe was...Instron Corp., Norwood, Massachusetts) was used to test breaking strength. Briefly, the skin and underlying disc was removed en-block measuring

Pharmacometrics and delivery of novel nanoformulated PEG-b-poly(ε-caprolactone) micelles of rapamycin

PubMed Central

Yáñez, Jaime A.; Forrest, M. Laird; Ohgami, Yusuke

2008-01-01

Purpose To determine the pharmacokinetics, tissue, and blood distribution of rapamycin PEG-block-poly(ε-caprolactone) (PEG-b-PCL) micelle formulations with and without the addition of α-tocopherol compared to control rapamycin in Tween 80/PEG 400/N,N-dimethylacetamide (DMA) (7:64:29). Methods Rapamycin was incorporated at 10% w/w into PEG-b-PCL micelles (5:10 kDa) using a solvent extraction technique. The co-incorporation of 2:1 α-tocopherol:PEG-b-PCL was also studied. Rapamycin was quantified utilizing LC/MS in a Waters XTerra MS C18 column with 32-desmethoxyrapamycin as the internal standard. Male Sprague Dawley rats (N = 4 per group; ~200 g) were cannulated via the left jugular and dosed intravenously (IV) with the rapamycin control and micelle formulations (10 mg/kg, 1:9 ratio for rapamycin to PEG-b-PCL). For tissue distribution 24 h after IV dosing, whole blood, plasma, red blood cells, and all the representative tissues were collected. The tissues were rapidly frozen under liquid nitrogen and ground to a fine powder. The rapamycin concentrations in plasma and red blood cells were utilized to determine the blood distribution (partition coefficient between plasma and red blood cells). For the determination of the pharmacokinetic parameters, blood, plasma, and urine samples were collected over 48 h. The pharmacokinetic parameters were calculated using WinNonlin® (Version 5.1) software. Results Rapamycin concentrations were considerably less in brain after administration of both micelle formulations compared to a rapamycin in the Tween 80/PEG 400/DMA control group. There was a 2-fold and 1.6-fold increase in the plasma fraction for rapamycin micelles with and without α-tocopherol. There was a decrease in volume of distribution for both formulations, an increase in AUC, a decrease in clearance, and increase in half life respectively for rapamycin in PEG-b-PCL + α-tocopherol micelles and in PEG-b-PCL micelles. There was no mortality with the micelle formulations compared to 60% mortality with rapamycin in Tween 80/PEG 400/DMA. Conclusions The decreased distribution into the brain of rapamycin in PEG-b-PCL micelles may ameliorate rapamycin neurotoxicity. Both micelle formulations increase rapamycin distribution in plasma, which could facilitate access into solid tumors. The micellar delivery systems of rapamycin impart in vivo controlled release, resulting in altered disposition, and dramatically reduced mortality. PMID:17393166

Nonselective Currents and Channels in Plasma Membranes of Protoplasts from Coats of Developing Seeds of Bean1

PubMed Central

Zhang, Wen-Hao; Skerrett, Martha; Walker, N. Alan; Patrick, John W.; Tyerman, Stephen D.

2002-01-01

In developing bean (Phaseolus vulgaris) seeds, phloem-imported nutrients move in the symplast from sieve elements to the ground parenchyma cells where they are transported across the plasma membrane into the seed apoplast. To study the mechanisms underlying this transport, channel currents in ground parenchyma protoplasts were characterized using patch clamp. A fast-activating outward current was found in all protoplasts, whereas a slowly activating outward current was observed in approximately 25% of protoplasts. The two currents had low selectivity for univalent cations, but the slow current was more selective for K+ over Cl− (PK:PCl = 3.6–4.2) than the fast current (PK:PCl = 1.8–2.5) and also displayed Ca2+ selectivity. The slow current was blocked by Ba2+, whereas both currents were blocked by Gd3+ and La3+. Efflux of K+ from seed coat halves was inhibited 25% by Gd3+ and La3+ but was stimulated by Ba2+ and Cs+, suggesting that only the fast current may be a component in the pathway for K+ release. An “instantaneous” inward current observed in all protoplasts exhibited similar pharmacology and permeability for univalent cations to the fast outward current. In outside-out patches, two classes of depolarization-activated cation-selective channels were observed: one slowly activating of low conductance (determined from nonstationary noise to be 2.4 pS) and another with conductances 10-fold higher. Both channels occurred at high density. The higher conductance channel in 10 mm KCl had PK:PCl = 2.8. Such nonselective channels in the seed coat ground parenchyma cell could function to allow some of the efflux of phloem-imported univalent ions into the seed apoplast. PMID:11842143

Molecular recognition in poly(epsilon-caprolactone)-based thermoplastic elastomers.

PubMed

Wisse, Eva; Spiering, A J H; van Leeuwen, Ellen N M; Renken, Raymond A E; Dankers, Patricia Y W; Brouwer, Linda A; van Luyn, Marja J A; Harmsen, Martin C; Sommerdijk, Nico A J M; Meijer, E W

2006-12-01

The molecular recognition properties of the hydrogen bonding segments in biodegradable thermoplastic elastomers were explored, aiming at the further functionalization of these potentially interesting biomaterials. A poly(epsilon-caprolactone)-based poly(urea) 2 was synthesized and characterized in terms of mechanical properties, processibility and histocompatibility. Comparison of the data with those obtained from the structurally related poly(urethane urea) 1 revealed that the difference in hard segment structure does not significantly affect the potency for application as a biomaterial. Nevertheless, the small differences in hard block composition had a strong effect on the molecular recognition properties of the hydrogen bonding segments. High selectivity was found for poly(urea) 2 in which bisureidobutylene-functionalized azobenzene dye 3 was selectively incorporated while bisureidopentylene-functionalized azobenzene dye 4 was completely released. In contrast, the incorporation of both dyes in poly(urethane urea) 1 led in both cases to their gradual release in time. Thermal analysis of the polymers in combination with variable temperature infrared experiments indicated that the hard blocks in 1 showed a sharp melting point, whereas those in 2 showed a very broad melting trajectory. This suggests a more precise organization of the hydrogen bonding segments in the hard blocks of poly(urea) 2 compared to poly(urethane urea) 1 and explains the results from the molecular recognition experiments. Preliminary results revealed that a bisureidobutylene-functionalized GRGDS peptide showed more supramolecular interaction with the PCL-based poly(urea), containing the bisureidobutylene recognition unit, as compared to HMW PCL, lacking this recognition unit.

Synthesis of Thermoresponsive Amphiphilic Polyurethane Gel as a New Cell Printing Material near Body Temperature.

PubMed

Tsai, Yi-Chun; Li, Suming; Hu, Shiaw-Guang; Chang, Wen-Chi; Jeng, U-Ser; Hsu, Shan-hui

2015-12-23

Waterborne polyurethane (PU) based on poly(ε-caprolactone) (PCL) diol and a second oligodiol containing amphiphilic blocks was synthesized in this study. The microstructure was characterized by dynamic light scattering (DLS), small-angle X-ray scattering (SAXS), and rheological measurement of the PU dispersion. The surface hydrophilicity measurement, infrared spectroscopy, wide-angle X-ray diffraction, mechanical and thermal analyses were conducted in solid state. It was observed that the presence of a small amount of amphiphilic blocks in the soft segment resulted in significant changes in microstructure. When 90 mol % PCL diol and 10 mol % amphiphilic blocks of poly(l-lactide)-poly(ethylene oxide) (PLLA-PEO) diol were used as the soft segment, the synthesized PU had a water contact angle of ∼24° and degree of crystallinity of ∼14%. The dispersion had a low viscosity below room temperature. As the temperature was raised to body temperature (37 °C), the dispersion rapidly (∼170 s) underwent sol-gel transition with excellent gel modulus (G' ≈ 6.5 kPa) in 20 min. PU dispersions with a solid content of 25-30% could be easily mixed with cells in sol state, extruded by a 3D printer, and deposited layer by layer as a gel. Cells remained alive and proliferating in the printed hydrogel scaffold. We expect that the development of novel thermoresponsive PU system can be used as smart injectable hydrogel and applied as a new type of bio-3D printing ink.

Shish-kebab-structured poly(ε-caprolactone) nanofibers hierarchically decorated with chitosan-poly(ε-caprolactone) copolymers for bone tissue engineering.

PubMed

Jing, Xin; Mi, Hao-Yang; Wang, Xin-Chao; Peng, Xiang-Fang; Turng, Lih-Sheng

2015-04-01

In this work, scaffolds with a shish-kebab (SK) structure formed by poly(ε-caprolactone) (PCL) nanofibers and chitosan-PCL (CS-PCL) copolymers were prepared via electrospinning and subsequent crystallization for bone tissue engineering applications. The aim of this study was to introduce nanosized topography and the high biocompatibility of chitosan onto PCL nanofibers to enhance cell affinity to PCL scaffolds. CS-PCL copolymers with various ratios were synthesized, and then spontaneously crystallized as kebabs onto the electrospun PCL fibers, which acted as shishes. Scanning electron microscopy (SEM) results demonstrated that the copolymer with PCL to chitosan ratio of 8.8 could hierarchically decorate the PCL nanofibers and formed well-shaped kebabs on the PCL nanofiber surface. Water contact angle tests and biomimetic activity experiments revealed that the shish-kebab scaffolds with CS-PCL kebabs (PCL-SK(CS-PCL(8.8))) showed enhanced hydrophilicity and mineralization ability compared with smooth PCL and PCL-SK(PCL) shish-kebab scaffolds. Osteoblast-like MG63 cells cultured on the PCL-SK(CS-PCL(8.8)) scaffolds showed optimizing cell attachment, cell viability, and metabolic activity, demonstrating that this kind of scaffold has potential applications in bone tissue engineering.

Practice Patterns for the Use of Antibiotic Agents in Damage Control Laparotomy and Its Impact on Outcomes.

PubMed

Goldberg, Stephanie R; Henning, Jennifer; Wolfe, Luke G; Duane, Therese M

2017-04-01

The purpose of this study was to identify practice patterns associated with the use of antimicrobial agents with damage control laparotomy (DCL) and the relationship with post-operative intra-abdominal infection (IAI) rates. The study was a retrospective review of trauma patients undergoing laparotomy at a Level 1 trauma center in 2010. Patients undergoing DCL versus those primarily closed (PCL) were compared for antimicrobial use (ABX) and its correlation with IAI rates (p < 0.05). Deaths with length of stay <5 days were excluded. A total of 121 patients were identified (28 DCL, 93 PCL). The DCL group was more severely injured (Injury Severity Score [ISS]: 31.4 ± 15 DCL vs. 18 ± 12.7 PCL, p < 0.001) with more small and large bowel injuries (SLBI), although not statistically significant (53.6% DCL vs. 35.5% PCL, p = 0.12). Practice patterns of ABX administration in terms of pre-operative (94.6% PCL vs. 69.2% DCL, p = 0.0012) and post-operative administration (PCL: 50.5% none, 21.5% one day, 28% long term >1 d; DCL: 21.4% none, 25.0% one day, 53.6% long term >1 day, p = 0.0130) were significant. Regression analyses demonstrated that neither ISS nor DCL was an independent predictor of infection, but pre-operative ABX was a negative predictor (odds ratio [OR] 0.20, 95% confidence interval [CI] 0.05-0.91, p = 0.037), while post-operative ABX (OR 6.7, 95%CI 1.33-33.8, p = 0.044) and SLBI (OR 3.45, CI 1.03-11.5, p = 0.02) were positive predictors of infection with an receiver operating characteristic of 0.81. Significant variations exist in the use of ABX in DCL and PCL. These variations may lead to deleterious results from both lack of initial pre-operative coverage and prolonged ABX use. The decrease in infection rates with pre-operative ABX yet significant increase with continued post-operative use even in the presence of SLBI suggests the need for a more standardized approach. With the increase in DCL and the open abdomen, more research is needed to clearly establish ABX protocols in this patient population.

The effect of a dynamic PCL brace on patellofemoral compartment pressures in PCL-and PCL/PLC-deficient knees.

PubMed

Welch, Tyler; Keller, Thomas; Maldonado, Ruben; Metzger, Melodie; Mohr, Karen; Kvitne, Ronald

2017-12-01

The natural history of posterior cruciate ligament (PCL) deficiency includes the development of arthrosis in the patellofemoral joint (PFJ). The purpose of this biomechanical study was to evaluate the hypothesis that dynamic bracing reduces PFJ pressures in PCL- and combined PCL/posterolateral corner (PLC)-deficient knees. Controlled Laboratory Study. Eight fresh frozen cadaveric knees with intact cruciate and collateral ligaments were included. PFJ pressures and force were measured using a pressure mapping system via a lateral arthrotomy at knee flexion angles of 30°, 60°, 90°, and 120° in intact, PCL-deficient, and PCL/PLC-deficient knees under a combined quadriceps/hamstrings load of 400 N/200 N. Testing was then repeated in PCL- and PCL/PLC-deficient knees after application of a dynamic PCL brace. Application of a dynamic PCL brace led to a reduction in peak PFJ pressures in PCL-deficient knees. In addition, the brace led to a significant reduction in peak pressures in PCL/PLC-deficient knees at 60°, 90°, and 120° of flexion. Application of the dynamic brace also led to a reduction in total PFJ force across all flexion angles for both PCL- and PCL/PLC-deficient knees. Dynamic bracing reduces PFJ pressures in PCL- and combined PCL/PLC-deficient knees, particularly at high degrees of knee flexion.

Bioresponsive polymer coated drug nanorods for breast cancer treatment

NASA Astrophysics Data System (ADS)

Laemthong, Tunyaboon; Kim, Hannah H.; Dunlap, Kelly; Brocker, Caitlin; Barua, Dipak; Forciniti, Daniel; Huang, Yue-Wern; Barua, Sutapa

2017-01-01

Ineffective drug release at the target site is among the top challenges for cancer treatment. This reflects the facts that interaction with the physiological condition can denature active ingredients of drugs, and low delivery to the disease microenvironment leads to poor therapeutic outcomes. We hypothesize that depositing a thin layer of bioresponsive polymer on the surface of drug nanoparticles would not only protect drugs from degradation but also allow the release of drugs at the target site. Here, we report a one-step process to prepare bioresponsive polymer coated drug nanorods (NRs) from liquid precursors using the solvent diffusion method. A thin layer (10.3 ± 1.4 nm) of poly(ε-caprolactone) (PCL) polymer coating was deposited on the surface of camptothecin (CPT) anti-cancer drug NRs. The mean size of PCL-coated CPT NRs was 500.9 ± 91.3 nm length × 122.7 ± 10.1 nm width. The PCL polymer coating was biodegradable at acidic pH 6 as determined by Fourier transform infrared spectroscopy. CPT drugs were released up to 51.5% when PCL coating dissolved into non-toxic carboxyl and hydroxyl groups. Trastuzumab (TTZ), a humanized IgG monoclonal antibody, was conjugated to the NR surface for breast cancer cell targeting. Combination treatments using CPT and TTZ decreased the HER-2 positive BT-474 breast cancer cell growth by 66.9 ± 5.3% in vitro. These results suggest effective combination treatments of breast cancer cells using bioresponsive polymer coated drug delivery.

Development of a High Efficiency Compressor/Expander for an Air Cycle Air Conditioning System.

DTIC Science & Technology

1982-11-15

bearing, lb PHUB - Hub pressure (initial guess), psia RLG - Rotor length 1 ’B-2 RPM - Rotational speed, RPM R - Gas constant, lb -ft/lb - R CP - Specific...Compressor discharge port pressure ratio (PCD/PC2).:- CDP - Compressor pressure change, PCD-PCl PHUB - Pressure in compressor hub (acting on base of vanes

Properties of thermoplastic starch and TPS/polycaprolactone blend reinforced with sisal whiskers using extrusion processing

USDA-ARS?s Scientific Manuscript database

Sisal whiskers (SW) were prepared by acid hydrolysis for subsequent evaluation as reinforcing material for biodegradable matrices of thermoplastic starch (TPS) and TPS/polycaprolactone (TPS/PCL) blends. The acid hydrolyzed SW had dimensions of 5±2 nm in diameter and 210±60 nm in length and 78% cryst...

Posterior double PCL sign: a case report of unusual MRI finding of bucket-handle tear of medial meniscus.

PubMed

Yoo, Jae Ho; Hahn, Sung Ho; Yi, Seung Rim; Kim, Seong Wan

2007-11-01

Among the MRI signs of bucket-handle tears of medial meniscus, double posterior cruciate ligament (PCL) sign denotes a low signal band anterior and parallel to the PCL, which looks like another PCL in MR images. If the bucket-handle fragment subsequently tears at the anterior horn, the torn meniscal substance can be displaced to the posterosuperior region of the PCL, and looks like another PCL behind the original PCL. We propose the lesion be called the "posterior double PCL sign" in contrast to the ordinary double PCL sign. We present a case showing the posterior double PCL sign.

Organic-inorganic hybrid nanocomposites based on chitosan derivatives and layered double hydroxides with intercalated phacolysin as ocular delivery system

NASA Astrophysics Data System (ADS)

Qin, Zhiguo; Zhang, Jie; Chi, Huibo; Cao, Feng

2015-12-01

This study was mainly aimed to evaluate the potential use of a novel ocular drug delivery system, organic-inorganic hybrid nanocomposites based on chitosan derivatives and layered double hydroxides (LDH). Organic polymers of chitosan-glutathione (CG) and pre-activated chitosan-glutathione (CG-2MNA) were successfully synthesized and characterized. LDH with intercalated phacolysin (PCL), including larger hexagonal LDH-PCL (Lh-LDH-PCL), larger spherical LDH-PCL (Ls-LDH-PCL), smaller hexagonal LDH-PCL (Sh-LDH-PCL), CG hybrid LDH-PCL (LDH-PCL-CG), and CG-2MNA hybrid LDH-PCL (LDH-PCL-CG-2MNA), were prepared. The nanocomposites with particle size of 107.2-274.9 nm were characterized by powder X-ray diffraction, Fourier transform infrared, transmission electron micrographs, etc. In vivo precorneal retention studies showed that the detectable time of all nanocomposites was prolonged from 2 to 6 h in comparison to PCL saline. Accordingly, the AUC0-6h values of Lh-LDH-PCL, Ls-LDH-PCL, Sh-LDH-PCL, LDH-PCL-CG, and LDH-PCL-CG-2MNA nanocomposites were increased by 2.27-, 2.08-, 3.08-, 4.67-, and 3.36-fold, respectively. The Draize test and hematoxylin and eosin staining demonstrated that modified LDH had no eye irritation after single and repeated administration. These results indicated that chitosan derivatives-LDH hybrid nanocomposite dispersion could be a promising ocular drug delivery system to improve precorneal retention time of drugs.

PCL and PCL-gelatin nanofibers as esophageal tissue scaffolds: optimization, characterization and cell-matrix interactions.

PubMed

Kuppan, Purushothaman; Sethuraman, Swaminathan; Krishnan, Uma Maheswari

2013-09-01

Nanofiber based scaffolds offer great promise in regeneration of various tissues including esophagus. Diseases of the esophagus such as malignancy and strictures require surgical intervention to repair the affected region using an appropriate substitute. Long gap esophageal atresia poses a clinical challenge to bridge the gap. In this study, nanofibrous scaffolds made of PCL and PCL-gelatin were fabricated through electrospinning. The average diameter of PCL and PCL-gelatin nanofibers were found to be 324 +/- 50 nm and 242 +/- 30 nm respectively. PCL-gelatin nanofibers was characterized using FTIR, DSC, UTM, Goniometer, suture retention strength and in vitro degradation and the results were compared with the PCL nanofibers. PCL nanofiber characterization results showed that it exhibited higher tensile strength, suture retention strength, contact angle and slower degradation when compared with the PCL-gelatin nanofibers. Further, the interaction of human esophageal epithelial cells with PCL and PCL-gelatin nanofibrous scaffold was determined by cell adhesion, proliferation and gene expression studies. Our results demonstrated that the epithelial cells adhered and proliferated well on both PCL and PCL-gelatin nanofibrous scaffolds and also exhibited the characteristic cobblestone morphology. Cell proliferation on PCL-gelatin nanofibrous scaffold was significantly higher than the PCL nanofibrous scaffold (*p <0.05). Therefore, these scaffolds could be explored as potential candidates for regeneration of functional esophagus.

Lower Extremity Limb Salvage with Cross Leg Pedicle Flap, Cross Leg Free Flap, and Cross Leg Vascular Cable Bridge Flap.

PubMed

Manrique, Oscar J; Bishop, Sarah N; Ciudad, Pedro; Adabi, Kian; Martinez-Jorge, Jorys; Moran, Steven L; Huang, Tony; Vijayasekaran, Aparna; Chen, Shih-Heng; Chen, Hung-Chi

2018-05-16

 Lower extremity salvage following significant soft tissue loss can be complicated by lack of recipient vessel for free tissue transfer. We describe our experience in lower limb salvage for patients with no recipient vessels with the use of pedicle, free and cable bridge flaps.  A retrospective review from 1985 to 2017 of patients undergoing lower limb salvage using a contralateral pedicle cross leg (PCL) flaps, free cross leg (FCL) flaps, or free cable bridge (FCB) flaps was conducted. Demographics, etiology of the reconstruction, type of flap used, donor-site vessels, defect size, operating time, time of pedicle division, length of hospital stay, time to ambulation, and complications were analyzed.  A total of 53 patients (48 males and 5 females) with an average age of 35 years (range, 29-38 years) were identified. The etiology for the reconstruction was trauma in 52 patients and oncological resection in 1 patient. There were 18 PCL, 25 FCL, and 10 FCB completed. The recipient vessels for all flaps were the posterior tibial artery and vein. The average operating room times for PCL, FCL, and FCB flaps were 4, 9, and 10 hours, respectively. The average length of hospital stay was 5 weeks and average time to ambulation was 4 weeks. The average follow-up time was 7.5 years (range, 3-12 years). Complications encountered were hematoma (six), prolonged pain (six), total flap loss (two), reoperation (five), and infection (four). Limb salvage rates were 96.2%.  When ipsilateral limb vessels are not available, and other reconstructive options have been exhausted, cross leg flaps can be a viable option for limb salvage in the setting of extensive defects. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

A novel MIS technique for posterior cruciate ligament avulsion fractures.

PubMed

Gavaskar, Ashok S; Karthik, Bhupesh; Gopalan, Hitesh; Srinivasan, Parthasarathy; Tummala, Naveen C

2017-08-01

Open surgical approaches to treat tibial avulsion fractures of the posterior cruciate ligament (PCL) often use large incisions involving extensive muscle dissection and retraction. The objective of this study was to describe a new mini-invasive approach targeting the fractured zone, to minimize surgical dissection and improve recovery and rehabilitation. The new approach was used in 15 males and seven females with isolated PCL avulsions. The length of the surgical incision, surgical time, need for conversion to open technique, visual analog scores (VAS) and duration of hospital stay were studied to assess the efficacy, learning curve and advantages of the new technique. Neurovascular complications were recorded. At the two-year follow-up, International Knee Documentation Committee (IKDC) scores were recorded to assess function. Patients were followed up for a mean of 29months (range: 34-41). The mean length of the incision was 4.1cm (range: 3.4 to five) measured at the end of the procedure. None of the patients required conversion to an open technique and no neurovascular complications were recorded. The mean surgical time was 40min (range: 25-50). The mean VAS on discharge was 2.2 (range: one to four) and patients stayed at the hospital for a mean of 2.2days (range: one to three). The mean IKDC score at one-year post surgery was 86.4 (range: 83.9-90.8). The new mini-invasive targeted approach provides adequate exposure for performing internal fixation of PCL avulsion fractures without the surgical morbidity associated with conventional open surgical approaches. The procedure is safe, fast and does not require a long learning curve. Copyright © 2017 Elsevier B.V. All rights reserved.

Enhancement of biodegradation and osseointegration of poly(ε-caprolactone)/calcium phosphate ceramic composite screws for osteofixation using calcium sulfate.

PubMed

Wu, Chang-Chin; Hsu, Li-Ho; Tsai, Yuh-Feng; Sumi, Shoichiro; Yang, Kai-Chiang

2016-04-04

Internal fixation devices, which can stabilize and realign fractured bone, are widely used in fracture management. In this paper, a biodegradable composite fixator, composed of poly(ε-caprolactone), calcium phosphate ceramic and calcium sulfate (PCL/CPC/CS), is developed. The composition of CS, which has a high dissolution rate, was expected to create a porous structure to improve osteofixation to the composite fixator. PCL, PCL/CPC, and PCL/CPC/CS samples were prepared and their physical properties were characterized in vitro. In vivo performance of the composite screws was verified in the distal femurs of rabbits. Results showed that the PCL/CPC/CS composite had a higher compressive strength (28.55 ± 3.32 MPa) in comparison with that of PCL (20.64 ± 1.81 MPa) (p < 0.05). A larger amount of apatite was formed on PCL/CPC/CS than on PCL/CPC, while no apatite was found on PCL after simulated body fluid immersion. In addition, PCL/CPC/CS composites also had a faster in vitro degradation rate (13.05 ± 3.42% in weight loss) relative to PCL (1.79 ± 0.23%) and PCL/CPC (4.32 ± 2.18%) (p < 0.001). In animal studies, PCL/CPC/CS screws showed a greater volume loss than that of PCL or PCL/CPC at 24 weeks post-implantation. Under micro-computerized tomography observation, animals with PCL/CPC/CS implants had better osseointegration in terms of the structural parameters of the distal metaphysis, including trabecular number, trabecular spacing, and connectivity density, than the PCL screw. This study reveals that the addition of CS accelerates the biodegradation and enhanced apatite formation of the PCL/CPC composite screw. This osteoconductive PCL/CPC/CS is a good candidate material for internal fixation devices.

Enhancement of electrical conductivity by changing phase morphology for composites consisting of polylactide and poly(ε-caprolactone) filled with acid-oxidized multiwalled carbon nanotubes.

PubMed

Xu, Zhaohua; Zhang, Yaqiong; Wang, Zhigang; Sun, Ning; Li, Heng

2011-12-01

Composites consisting of polylactide (PLA) and poly(ε-caprolactone) (PCL) filled with acid-oxidized multiwalled carbon nanotubes (A-MWCNTs) were prepared through melt compounding. Phase morphologies of PLA/PCL/A-MWCNT composites with different contents of filled A-MWCNTs and PCL compositions were mainly observed by scanning electron microscope. The results show that A-MWCNTs are selectively dispersed in the PCL phase, regardingless of PCL phase domain sizes. For PLA/PCL/A-MWCNT composites with fixed PLA/PCL ratio of 95/5, the dispersed PCL phase domain sizes in the PLA matrix decrease even though a small content of A-MWCNTs is added, compared with PLA/PCL blend with the same composition, indicating that A-MWCNTs effectively prevent from coalescence of the dispersed PCL phase domains. With filling of 1.0 wt % A-MWCNTs, an interesting change of electrical conductivity for PLA/PCL/A-MWCNT composites is observed, in which the maximum conductivity is observed for PLA/PCL/A-MWCNT composite with PLA/PCL ratio of 60/40. The result is well-explained by the formed cocontinuous phase morphology and effective A-MWCNT content. © 2011 American Chemical Society

Validation, Intrarater and Interrater Reliability Study of the Lateral-Anterior Drawer Test for Detecting Posterior Cruciate Ligament Ruptures: Study Protocol of a Prospective Controlled Single-Blinded Cross-Sectional Study.

PubMed

Seeber, Gesine H; Thalhamer, Christoph; Hahne, Julia; Matthijs, Omer

2018-05-29

Commonly used clinical tests for posterior cruciate ligament (PCL) rupture detection exhibit several limitations, thus requiring more precise clinical PCL tests. The lateral-anterior drawer (LAD) test has been proposed as a manually applied testing alternative but not yet been evaluated in vivo. Fifteen patients presenting with an MRI-confirmed acute or chronic unilateral PCL rupture and 15 subjects with no prior knee injury in their medical history will be included in this prospective single-blinded cross-sectional cohort study. Three examiners with different lengths of working experience (range 1-30 years), blinded to MRI outcomes and patient history, will use the LAD test on both knees of each participant to test for PCL integrity. Examiners will independently document the PCL status of each knee on a blank case report form. Fleiss-Kappa values will be calculated to investigate whether the LAD test shows clinically significant interrater and intrarater reliability. Furthermore, LAD test outcomes will be compared with MRI which serves as reference standard to check for concurrent validity. Moreover, LAD test accuracy with respect to tester experience will be evaluated. The study will be conducted in agreement with the World Medical Association Declaration of Helsinki (2013). Ethical permission (EK16-081-0616) to conduct this study was obtained from the review board of the city of Vienna on 1 September 2016. All personal and research data will be used in accordance with the Austrian Federal Data Protection Act and will be anonymised before publication in relevant international peer-reviewed journals. DRKS00013268; Pre-results. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Electrospun photosensitive nanofibers: potential for photocurrent therapy in skin regeneration.

PubMed

Jin, Guorui; Prabhakaran, Molamma P; Kai, Dan; Kotaki, Masaya; Ramakrishna, Seeram

2013-01-01

Poly(3-hexylthiophene) (P3HT) is one of the most promising photovoltaic (PV) polymers in photocurrent therapy. A novel photosensitive scaffold for skin tissue engineering was fabricated by blending P3HT with polycaprolactone (PCL) and electrospun to obtain composite PCL/P3HT nanofibers with three different weight ratios of PCL : P3HT (w/w) of 150 : 2 [PCL/P3HT(2)], 150 : 10 [PCL/P3HT(10)] and 150 : 20 [PCL/P3HT(20)]. The photosensitive properties of the blend solutions and the composite nanofibers of PCL/P3HT were investigated. The incident photon-to-electron conversion efficiencies of the PCL/P3HT(2), PCL/P3HT(10), PCL/P3HT(20) were identified as 2.0 × 10(-6), 1.6 × 10(-5) and 2.9 × 10(-5), respectively, which confirm the photosensitive ability of the P3HT-containing scaffolds. The biocompatibility of the scaffold was evaluated by culturing human dermal fibroblasts and the results showed that the proliferation of HDFs under light stimulation on PCL/P3HT(10) was 12.8%, 11.9%, and 11.6% (p ≤ 0.05) higher than the cell growth on PCL, PCL/P3HT(2) and PCL/P3HT(20), respectively. Human dermal fibroblasts cultured under light stimulation on PCL/P3HT(10) not only showed better cell proliferation but also retained cell morphology similar to the phenotype observed on tissue culture plates (control). Our experimental results suggest novel and potential application of an optimized amount of P3HT-containing scaffold, especially PCL/P3HT(10) nanofibrous scaffold in photocurrent therapy for skin regeneration.

Further Theoretical Insight into the Mechanical Properties of Polycaprolactone Loaded with Organic–Inorganic Hybrid Fillers

PubMed Central

Maietta, Saverio; Russo, Teresa; De Santis, Roberto; Ronca, Dante; Riccardi, Filomena; Martorelli, Massimo; Gloria, Antonio

2018-01-01

Experimental/theoretical analyses have already been performed on poly(ε-caprolactone) (PCL) loaded with organic–inorganic fillers (PCL/TiO2 and PCL/ZrO2) to find a correlation between the results from the small punch test and Young’s modulus of the materials. PCL loaded with Ti2 (PCL = 12, TiO2 = 88 wt %) and Zr2 (PCL = 12, ZrO2 = 88 wt %) hybrid fillers showed better performances than those obtained for the other particle composition. In this context, the aim of current research is to provide further insight into the mechanical properties of PCL loaded with sol–gel-synthesized organic–inorganic hybrid fillers for bone tissue engineering. For this reason, theoretical analyses were performed by the finite element method. The results from the small punch test and Young’s modulus of the materials were newly correlated. The obtained values of Young’s modulus (193 MPa for PCL, 378 MPa for PCL/Ti2 and 415 MPa for PCL/Zr2) were higher than those obtained from a previous theoretical modelling (144 MPa for PCL, 282 MPa for PCL/Ti2 and 310 MPa for PCL/Zr2). This correlation will be an important step for the evaluation of Young’s modulus, starting from the small punch test data. PMID:29466299

Further Theoretical Insight into the Mechanical Properties of Polycaprolactone Loaded with Organic-Inorganic Hybrid Fillers.

PubMed

Maietta, Saverio; Russo, Teresa; Santis, Roberto De; Ronca, Dante; Riccardi, Filomena; Catauro, Michelina; Martorelli, Massimo; Gloria, Antonio

2018-02-21

Experimental/theoretical analyses have already been performed on poly(ε-caprolactone) (PCL) loaded with organic-inorganic fillers (PCL/TiO₂ and PCL/ZrO₂) to find a correlation between the results from the small punch test and Young's modulus of the materials. PCL loaded with Ti2 (PCL = 12, TiO₂ = 88 wt %) and Zr2 (PCL = 12, ZrO₂ = 88 wt %) hybrid fillers showed better performances than those obtained for the other particle composition. In this context, the aim of current research is to provide further insight into the mechanical properties of PCL loaded with sol-gel-synthesized organic-inorganic hybrid fillers for bone tissue engineering. For this reason, theoretical analyses were performed by the finite element method. The results from the small punch test and Young's modulus of the materials were newly correlated. The obtained values of Young's modulus (193 MPa for PCL, 378 MPa for PCL/Ti2 and 415 MPa for PCL/Zr2) were higher than those obtained from a previous theoretical modelling (144 MPa for PCL, 282 MPa for PCL/Ti2 and 310 MPa for PCL/Zr2). This correlation will be an important step for the evaluation of Young's modulus, starting from the small punch test data.

The role of isolated posterior cruciate ligament reconstruction in knees with combined posterior cruciate ligament and posterolateral complex injury.

PubMed

Lee, Dong-Yeong; Park, Young-Jin; Kim, Dong-Hee; Kim, Hyun-Jung; Nam, Dae-Cheol; Park, Jin-Sung; Hwang, Sun-Chul

2017-08-14

This is a meta-analysis comparing biomechanical outcomes to determine whether an isolated posterior cruciate ligament (PCL) reconstruction can restore normal knee kinematics in a combined PCL/posterolateral complex (PLC) injury and whether double-bundle (DB) PCL reconstruction is superior in controlling posterior and rotational laxity compared with single-bundle (SB) PCL reconstruction in a PCL/PLC-deficient knee. A number of electronic databases were searched for relevant articles published through August 2016 that compared biomechanical outcomes of PCL reconstruction in patients who underwent reconstruction for combined PCL/PLC deficiencies. Data were searched, extracted, analysed, and assessed for quality according to Cochrane Collaboration guidelines, and biomechanical outcomes were evaluated using various outcome values. The results are presented as relative ratios for binary outcomes and standard mean differences for continuous outcomes with 95% confidence intervals. Five biomechanical studies were included in this meta-analysis. There were significant differences in laxities such as posterior tibial translation (PTT), external rotation, varus rotation, and PTT coupled with external rotation in the isolated PCL reconstruction group compared with the native PCL group. Furthermore, there were no significant differences in laxities such as PTT, external rotation, or varus rotation between the SB and DB PCL reconstruction groups. Isolated PCL reconstruction, whether SB or DB, could not restore normal knee kinematics in the PCL/PLC-deficient knee. In such cases, residual laxity after isolated PCL reconstruction can be controlled successfully with PLC reconstruction. Therefore, simultaneous PCL and PLC reconstruction is recommended for patients with combined PCL/PLC injury.

The in vitro and in vivo biocompatibility evaluation of electrospun recombinant spider silk protein/PCL/gelatin for small caliber vascular tissue engineering scaffolds.

PubMed

Xiang, Ping; Wang, Shan-Shan; He, Meng; Han, Yong-He; Zhou, Zhi-Hua; Chen, Deng-Long; Li, Min; Ma, Lena Q

2018-03-01

Recombinant spider silk protein (pNSR32) and gelatin (Gt) were demonstrated to enhance cytocompatibility of electrospun pNSR32/PCL/Gt scaffold. However, its potential pro-inflammatory effects and interactions with tissue and blood are unknown. In this study, the physicochemical properties and in vitro and in vivo biocompatibility of such scaffolds were evaluated. The results showed that the pNSR32/PCL/Gt scaffold possessed larger average fiber diameters, wider fiber diameter distribution and faster degradation rate than that of pNSR32/PCL and PCL scaffolds. The addition of pNSR32 and Gt had little influence on the hemolysis and plasma re-calcification time, but prolonged kinetic clotting time and reduced the platelet adhesion. The Il-6 and Tnf-α mRNA expression levels were up-regulated in macrophages seeded on the PCL and pNSR32/PCL scaffolds. The lowest release of IL-6 and TNF-α appeared in the pNSR32/PCL/Gt scaffold. Histological results revealed that the PCL and pNSR32/PCL scaffolds elicited severe host tissue responses after implantation, while prominent ingrowth of host cells were observed in the pNSR32/PCL and pNSR32/PCL/Gt scaffolds. The comet assay and bone marrow micronucleus test demonstrated that the pNSR32/PCL/Gt scaffold did not increase the frequency of DNA damage or bone marrow micronucleus. In short, this study confirmed that the pNSR32/PCL/Gt scaffold exhibited better blood and tissue compatibility than pNSR32/PCL and PCL scaffolds. No induction of genotoxicity and inflammatory factor releases makes the pNSR32/PCL/Gt scaffold a good candidate for engineering small diameter vascular tissue. Copyright © 2017. Published by Elsevier B.V.

Crystallization, mechanical properties, and controlled enzymatic degradation of biodegradable poly(epsilon-caprolactone)/multi-walled carbon nanotubes nanocomposites.

PubMed

Qiu, Zhaobin; Wang, Huishan; Xu, Changling

2011-09-01

Biodegradable poly(epsilon-caprolactone) (PCL)/multi-walled carbon nanotubes containing carboxylic groups (f-MWNTs) nanocomposites were prepared via simple melt compounding at low f-MWNTs loading in this work. Scanning and transmission electron microscopy observations indicate a homogeneous and fine distribution of f-MWNTs throughout the PCL matrix. The effect of low f-MWNTs loading on the crystallization, mechanical properties, and controlled enzymatic degradation of PCL in the nanocomposites were studied in detail with various techniques. The experimental results indicate that the incorporation of f-MWNTs enhances both the nonisothermal crystallization peak temperature and the overall isothermal crystallization rate of PCL in the PCL/f-MWNTs nanocomposites relative to neat PCL; moreover, the incorporation of a small quantity of f-MWNTs has improved apparently the mechanical properties of the PCL/MWNTs nanocomposites compared to neat PCL. The enzymatic degradation of neat PCL and the PCL/f-MWNTs nanocomposites at low f-MWNTs loading was studied in detail. The variation of weight loss with enzymatic degradation time, the surface morphology change, the reduced film thickness, the appearance of f-MWNTs on the surface of the films, and the almost unchanged molecular weight after enzymatic degradation suggest that the enzymatic degradation of neat PCL and the PCL/f-MWNTs nanocomposites may proceed via surface erosion mechanism. The presence of f-MWNTs reduces the enzymatic degradation rate of the PCL matrix in the nanocomposites compared with that of the pure PCL film.

Strong synergistic effects in PLA/PCL blends: Impact of PLA matrix viscosity.

PubMed

Ostafinska, Aleksandra; Fortelný, Ivan; Hodan, Jiří; Krejčíková, Sabina; Nevoralová, Martina; Kredatusová, Jana; Kruliš, Zdeněk; Kotek, Jiří; Šlouf, Miroslav

2017-05-01

Blends of two biodegradable polymers, poly(lactic acid) (PLA) and poly(ϵ-caprolactone) (PCL), with strong synergistic improvement in mechanical performance were prepared by melt-mixing using the optimized composition (80/20) and the optimized preparation procedure (a melt-mixing followed by a compression molding) according to our previous study. Three different PLA polymers were employed, whose viscosity decreased in the following order: PLC ≈ PLA1 > PLA2 > PLA3. The blends with the highest viscosity matrix (PLA1/PCL) exhibited the smallest PCL particles (d∼0.6μm), an elastic-plastic stable fracture (as determined from instrumented impact testing) and the strongest synergistic improvement in toughness (>16× with respect to pure PLA, exceeding even the toughness of pure PCL). According to the available literature, this was the highest toughness improvement in non-compatiblized PLA/PCL blends ever achieved. The decrease in the matrix viscosity resulted in an increase in the average PCL particle size and a dramatic decrease in the overall toughness: the completely stable fracture (for PLA1/PCL) changed to the stable fracture followed by unstable crack propagation (for PLA2/PCL) and finally to the completely brittle fracture (for PLA3/PCL). The stiffness of all blends remained at well acceptable level, slightly above the theoretical predictions based on the equivalent box model. Despite several previous studies, the results confirmed that PLA and PCL could behave as compatible polymers, but the final PLA/PCL toughness is extremely sensitive to the PCL particle size distribution, which is influenced by both processing conditions and PLA viscosity. PLA/PCL blends with high stiffness (due to PLA) and toughness (due to PCL) are very promising materials for medical applications, namely for the bone tissue engineering. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tissue engineering scaffolds of mesoporous magnesium silicate and poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone) composite.

PubMed

He, Dawei; Dong, Wei; Tang, Songchao; Wei, Jie; Liu, Zhenghui; Gu, Xiaojiang; Li, Ming; Guo, Han; Niu, Yunfei

2014-06-01

Mesoporous magnesium silicate (m-MS) and poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone) (PCL-PEG-PCL) composite scaffolds were fabricated by solvent-casting and particulate leaching method. The results suggested that the incorporation of m-MS into PCL-PEG-PCL could significantly improve the water adsorption of the m-MS/PCL-PEG-PCL composite (m-MPC) scaffolds. The in vitro degradation behavior of m-MPC scaffolds were determined by testing weight loss of the scaffolds after soaking into phosphate buffered saline (PBS), and the result showed that the degradation of m-MPC scaffolds was obviously enhanced by addition of m-MS into PCL-PEG-PCL after soaking for 10 weeks. Proliferation of MG63 cells on m-MPC was significantly higher than MPC scaffolds at 4 and 7 days. ALP activity on the m-MPC was obviously higher than MPC scaffolds at 7 days, revealing that m-MPC could promote cell differentiation. Histological evaluation showed that the introduction of m-MS into PCL-PEG-PCL enhanced the efficiency of new bone formation when the m-MPC scaffolds implanted into bone defect of rabbits. The results suggested that the inorganic/organic composite of m-MS and PCL-PEG-PCL scaffolds exhibited good biocompatibility, degradability and osteogenesis.

Copolymerization of Glycolide and ɛ-Caprolactone Using 12-Aminolauric Acid Modified Montmorillonite

NASA Astrophysics Data System (ADS)

Gallos, HAV; Reyes, LQ

2017-09-01

Poly(glycolide-co-ɛ-caprolactone) (PGLYCL) nanocomposites were prepared by copolymerization glycolide (GLY) and ɛ-caprolactone (ɛ-CL) in the presence of varying loadings 12-aminolauric acid (12-ALA)-modified montmorillonite. Copolymerization was successfully achieved based on the increase in polymer molecular weight after the reaction determined by gel permeation chromatography (GPC). The amount of the poly(glycolide) block and poly(ɛ-caprolactone) block units in the copolymer, identified by proton nuclear magnetic resonance (1H-NMR) spectroscopy, suggested that the increase in organo-clay loading cause a reduction GLYL: ɛ-CLL ratio. The arrangement of the monomers in the polymer products was elucidated to have an ABA triblock structure, where PCL block is the central block and the PGLY is found at both end of the copolymer. The presence of intercalated and exfoliated silicates in the nanocomposites were observed by x-ray diffraction (XRD) analysis. The biocompatibility of the nanocomposites with NCTC 292 mouse normal fibroblast was high relative to untreated cell cultures using tetrazolium bromide (MTT)-dye reduction assay.

Multi-biofunctional polymer graphene composite for bone tissue regeneration that elutes copper ions to impart angiogenic, osteogenic and bactericidal properties.

PubMed

Jaidev, L R; Kumar, Sachin; Chatterjee, Kaushik

2017-11-01

Despite several recent advances, poor vascularization in implanted scaffolds impedes complete regeneration for clinical success of bone tissue engineering. The present study aims to develop a multi-biofunctional nanocomposite for bone tissue regeneration using copper nanoparticle decorated reduced graphene oxide (RGO_Cu) hybrid particles in polycaprolactone (PCL) matrix (PCL/RGO_Cu). X-ray photoelectron spectroscopy and X-ray diffraction confirmed the presence of copper oxides (CuO and Cu 2 O) on RGO. Thermogravimetric analysis showed that 11.8% of copper was decorated on RGO. PCL/RGO_Cu exhibited steady release of copper ions in contrast to burst release from the composite containing copper alone (PCL/Cu). PCL/RGO_Cu exhibited highest modulus due to enhanced filler exfoliation. Endothelial cells rapidly proliferated on PCL/RGO_Cu confirming cytocompatibility. The sustained release of ions from PCL/RGO_Cu composites augmented tube formation by endothelial cells evidenced enhanced angiogenic activity. Gene expression of angiogenic markers VEGF and ANG-2 was higher on PCL/RGO_Cu compared to PCL. The osteogenic activity of PCL/RGO_Cu was confirmed by the 87% increase in mineral deposition by pre-osteoblasts compared to PCL. The bactericidal activity of PCL/RGO_Cu showed 78% reduction in viability of Escherichia coli. Thus, the multi-biofunctional PCL/RGO_Cu composite exhibits angiogenic, osteogenic and bactericidal properties, a step towards addressing some of the critical challenges in bone tissue engineering. Copyright © 2017 Elsevier B.V. All rights reserved.

Design of polyaspartic acid peptide-poly (ethylene glycol)-poly (ε-caprolactone) nanoparticles as a carrier of hydrophobic drugs targeting cancer metastasized to bone

PubMed Central

Liu, Jinsong; Zeng, Youyun; Shi, Shuai; Xu, Lihua; Zhang, Hualin; Pathak, Janak L; Pan, Yihuai

2017-01-01

Treatment of cancer metastasized to bone is still a challenge due to hydrophobicity, instability, and lack of target specificity of anticancer drugs. Poly (ethylene glycol)-poly (ε-caprolactone) polymer (PEG-PCL) is an effective, biodegradable, and biocompatible hydrophobic drug carrier, but lacks bone specificity. Polyaspartic acid with eight peptide sequences, that is, (Asp)8, has a strong affinity to bone surface. The aim of this study was to synthesize (Asp)8-PEG-PCL nanoparticles as a bone-specific carrier of hydrophobic drugs to treat cancer metastasized to bone. 1H nuclear magnetic resonance, Fourier transform infrared spectroscopy, and transmission electron microscopy data showed that (Asp)8-PEG-PCL nanoparticles (size 100 nm) were synthesized successfully. (Asp)8-PEG-PCL nanoparticles did not promote erythrocyte aggregation. Fluorescence microscopy showed clear uptake of Nile red-loaded (Asp)8-PEG-PCL nanoparticles by cancer cells. (Asp)8-PEG-PCL nanoparticles did not show cytotoxic effect on MG63 and human umbilical vein endothelial cells at the concentration of 10–800 μg/mL. (Asp)8-PEG-PCL nanoparticles bound with hydroxyapatite 2-fold more than PEG-PCL. Intravenously injected (Asp)8-PEG-PCL nanoparticles accumulated 2.7-fold more on mice tibial bone, in comparison to PEG-PCL. Curcumin is a hydrophobic anticancer drug with bone anabolic properties. Curcumin was loaded in the (Asp)8-PEG-PCL. (Asp)8-PEG-PCL showed 11.07% loading capacity and 95.91% encapsulation efficiency of curcumin. The curcumin-loaded (Asp)8-PEG-PCL nanoparticles gave sustained release of curcumin in high dose for >8 days. The curcumin-loaded (Asp)8-PEG-PCL nanoparticles showed strong antitumorigenic effect on MG63, MCF7, and HeLa cancer cells. In conclusion, (Asp)8-PEG-PCL nanoparticles were biocompatible, permeable in cells, a potent carrier, and an efficient releaser of hydrophobic anticancer drug and were bone specific. The curcumin-loaded (Asp)8-PEG-PCL nanoparticles showed strong antitumorigenic ability in vitro. Therefore, (Asp)8-PEG-PCL nanoparticles could be a potent carrier of hydrophobic anticancer drugs to treat the cancer metastasized to bone. PMID:28507436

Design of polyaspartic acid peptide-poly (ethylene glycol)-poly (ε-caprolactone) nanoparticles as a carrier of hydrophobic drugs targeting cancer metastasized to bone.

PubMed

Liu, Jinsong; Zeng, Youyun; Shi, Shuai; Xu, Lihua; Zhang, Hualin; Pathak, Janak L; Pan, Yihuai

2017-01-01

Treatment of cancer metastasized to bone is still a challenge due to hydrophobicity, instability, and lack of target specificity of anticancer drugs. Poly (ethylene glycol)-poly (ε-caprolactone) polymer (PEG-PCL) is an effective, biodegradable, and biocompatible hydrophobic drug carrier, but lacks bone specificity. Polyaspartic acid with eight peptide sequences, that is, (Asp) 8 , has a strong affinity to bone surface. The aim of this study was to synthesize (Asp) 8 -PEG-PCL nanoparticles as a bone-specific carrier of hydrophobic drugs to treat cancer metastasized to bone. 1 H nuclear magnetic resonance, Fourier transform infrared spectroscopy, and transmission electron microscopy data showed that (Asp) 8 -PEG-PCL nanoparticles (size 100 nm) were synthesized successfully. (Asp) 8 -PEG-PCL nanoparticles did not promote erythrocyte aggregation. Fluorescence microscopy showed clear uptake of Nile red-loaded (Asp) 8 -PEG-PCL nanoparticles by cancer cells. (Asp) 8 -PEG-PCL nanoparticles did not show cytotoxic effect on MG63 and human umbilical vein endothelial cells at the concentration of 10-800 μg/mL. (Asp) 8 -PEG-PCL nanoparticles bound with hydroxyapatite 2-fold more than PEG-PCL. Intravenously injected (Asp) 8 -PEG-PCL nanoparticles accumulated 2.7-fold more on mice tibial bone, in comparison to PEG-PCL. Curcumin is a hydrophobic anticancer drug with bone anabolic properties. Curcumin was loaded in the (Asp) 8 -PEG-PCL. (Asp) 8 -PEG-PCL showed 11.07% loading capacity and 95.91% encapsulation efficiency of curcumin. The curcumin-loaded (Asp) 8 -PEG-PCL nanoparticles gave sustained release of curcumin in high dose for >8 days. The curcumin-loaded (Asp) 8 -PEG-PCL nanoparticles showed strong antitumorigenic effect on MG63, MCF7, and HeLa cancer cells. In conclusion, (Asp) 8 -PEG-PCL nanoparticles were biocompatible, permeable in cells, a potent carrier, and an efficient releaser of hydrophobic anticancer drug and were bone specific. The curcumin-loaded (Asp) 8 -PEG-PCL nanoparticles showed strong antitumorigenic ability in vitro. Therefore, (Asp) 8 -PEG-PCL nanoparticles could be a potent carrier of hydrophobic anticancer drugs to treat the cancer metastasized to bone.

Radionuclide therapy using ¹³¹I-labeled anti-epidermal growth factor receptor-targeted nanoparticles suppresses cancer cell growth caused by EGFR overexpression.

PubMed

Li, Wei; Liu, Zhongyun; Li, Chengxia; Li, Ning; Fang, Lei; Chang, Jin; Tan, Jian

2016-03-01

Anti-epidermal growth factor receptor (EGFR)-targeted nanoparticles can be used to deliver a therapeutic and imaging agent to EGFR-overexpressing tumor cells. (131)I-labeled anti-EGFR nanoparticles derived from cetuximab were used as a tumor-targeting vehicle in radionuclide therapy. This paper describes the construction of the anti-EGFR nanoparticle EGFR-BSA-PCL. This nanoparticle was characterized for EGFR-targeted binding and cellular uptake in EGFR-overexpressing cancer cells by using flow cytometry and confocal microscopy. Anti-EGFR and non-targeted nanoparticles were labeled with (131)I using the chloramine-T method. Analyses of cytotoxicity and targeted cell killing with (131)I were performed using the MTT assay. The time-dependent cellular uptake of (131)I-labeled anti-EGFR nanoparticles proved the slow-release effects of nanoparticles. A radioiodine therapy study was also performed in mice. The EGFR-targeted nanoparticle EGFR-BSA-PCL and the non-targeted nanoparticle BSA-PCL were constructed; the effective diameters were approximately 100 nm. The results from flow cytometry and confocal microscopy revealed significant uptake of EGFR-BSA-PCL in EGFR-overexpressing tumor cells. Compared with EGFR-BSA-PCL, BSA-PCL could also bind to cells, but tumor cell retention was minimal and weak. In MTT assays, the EGFR-targeted radioactive nanoparticle (131)I-EGFR-BSA-PCL showed greater cytotoxicity and targeted cell killing than the non-targeted nanoparticle (131)I-BSA-PCL. The radioiodine uptake of both (131)I-labeled nanoparticles, (131)I-EGFR-BSA-PCL and (131)I-BSA-PCL, was rapid and reached maximal levels 4 h after incubation, but the (131)I uptake of (131)I-EGFR-BSA-PCL was higher than that of (131)I-BSA-PCL. On day 15, the average tumor volumes of the (131)I-EGFR-BSA-PCL and (131)I-BSA-PCL groups showed a slow growth relationship compared with that of the control group. The EGFR-targeted nanoparticle EGFR-BSA-PCL demonstrated superior cellular binding and uptake compared with those of the control BSA-PCL. The EGFR-targeted radioactive nanoparticle (131)I-EGFR-BSA-PCL exhibited favorable intracellular retention of (131)I. Radionuclide therapy using (131)I-EGFR-BSA-PCL, which showed excellent targeted cell killing, suppressed cancer cell growth caused by EGFR overexpression.

Surface-modified functionalized polycaprolactone scaffolds for bone repair: in vitro and in vivo experiments.

PubMed

Jensen, Jonas; Rölfing, Jan Hendrik Duedal; Le, Dang Quang Svend; Kristiansen, Asger Albaek; Nygaard, Jens Vinge; Hokland, Lea Bjerre; Bendtsen, Michael; Kassem, Moustapha; Lysdahl, Helle; Bünger, Cody Eric

2014-09-01

A porcine calvaria defect study was carried out to investigate the bone repair potential of three-dimensional (3D)-printed poly-ε-caprolactone (PCL) scaffolds embedded with nanoporous PCL. A microscopic grid network was created by rapid prototyping making a 3D-fused deposition model (FDM-PCL). Afterward, the FDM-PCL scaffolds were infused with a mixture of PCL, water, and 1,4-dioxane and underwent a thermal-induced phase separation (TIPS) followed by lyophilization. The TIPS process lead to a nanoporous structure shielded by the printed microstructure (NSP-PCL). Sixteen Landrace pigs were divided into two groups with 8 and 12 weeks follow-up, respectively. A total of six nonpenetrating holes were drilled in the calvaria of each animal. The size of the cylindrical defects was h 10 mm and Ø 10 mm. The defects were distributed randomly using following groups: (a) NSP-PCL scaffold, (b) FDM-PCL scaffold, (c) autograft, (d) empty defect, (a1) NSP-PCL scaffold + autologous mononuclear cells, and (a2) NSP-PCL scaffold + bone morphogenetic protein 2. Bone volume to total volume was analyzed using microcomputed tomography (µCT) and histomorphometry. The µCT and histological data showed significantly less bone formation in the NSP-PCL scaffolds in all three variations after both 8 and 12 weeks compared to all other groups. The positive autograft control had significantly higher new bone formation compared to all other groups except the FDM-PCL when analyzed using histomorphometry. The NSP-PCL scaffolds were heavily infiltrated with foreign body giant cells suggesting an inflammatory response and perhaps active resorption of the scaffold material. The unmodified FDM-PCL scaffold showed good osteoconductivity and osseointegration after both 8 and 12 weeks. © 2013 Wiley Periodicals, Inc.

Phase transitions and structural formation of PEG-PCL-PEG copolymer in the processes of fused deposition 3D printing

NASA Astrophysics Data System (ADS)

Dunaev, A.; Mariyanac, A.; Mironov, A.; Mironova, O.; Popov, V.; Syachina, M.

2018-04-01

In present work the analysis of thermal field distribution and thermal analysis were used to study phase and structural transformations in the block copolymer of polycaprolactone and polyethylene glycol in the process of scaffolds fabrication for tissue engineering using fused deposition modeling. It was shown that the intact polymer has a noticeable thermal history and formed degree of crystallinity which is close to its equilibrium value, while the microstructure of the polymer stays unchanged.

Rapid response oxygen-sensing nanofibers

PubMed Central

Xue, Ruipeng; Behera, Prajna; Viapiano, Mariano S.; Lannutti, John J.

2014-01-01

Molecular oxygen has profound effects on cell and tissue viability. Relevant sensor forms that can rapidly determine dissolved oxygen levels under biologically relevant conditions provide critical metabolic information. Using 0.5 μm diameter electrospun polycaprolactone (PCL) fiber containing an oxygen-sensitive probe, tris (4,7-diphenyl-1,10-phenanthroline) ruthenium(II) dichloride, we observed a response time of 0.9±0.12 seconds – 4–10 times faster than previous reports – while the t95 for the corresponding film was more than two orders of magnitude greater. Interestingly, the response and recovery times of slightly larger diameter PCL fibers were 1.79±0.23 s and 2.29±0.13 s, respectively, while the recovery time was not statistically different likely due to the more limited interactions of nitrogen with the polymer matrix. A more than 10-fold increase in PCL fiber diameter reduces oxygen sensitivity while having minor effects on response time; conversely, decreases in fiber diameter to less than 0.5 μm would likely decrease response times even further. In addition, a 50°C heat treatment of the electrospun fiber resulted in both increased Stern-Volmer slope and linearity likely due to secondary recrystallization that further homogenized the probe microenvironment. At exposure times up to 3600 s in length, photobleaching was observed but was largely eliminated by the use of either polyethersulfone (PES) or a PES-PCL core-shell composition. However, this resulted in 2- and 3-fold slower response times. Finally, even the non-core shell compositions containing the Ru oxygen probe result in no apparent cytotoxicity in representative glioblastoma cell populations. PMID:23706233

Grafting polycaprolactone diol onto cellulose nanocrystals via click chemistry: Enhancing thermal stability and hydrophobic property.

PubMed

Zhou, Ling; He, Hui; Li, Mei-Chun; Huang, Siwei; Mei, Changtong; Wu, Qinglin

2018-06-01

Hydrophobic and thermally-stable cellulose nanocrystals (CNCs) were synthesized by polycarpolactone diol (PCL diol) grafting via click chemistry strategy. The synthesis was designed as a three-step procedure containing azide-modification of CNCs, alkyne-modification of PCL diol and sequent copper(I)-catalyzed azide-alkyne cycloaddition reaction. The structure of azide-modified CNCs and alkyne-modified PCL diol, the structure, hydrophobic ability and thermal stability of click products CNC-PCL were characterized. FTIR, XPS and H 1 NMR results indicated a successful grafting of the N 3 groups onto the CNCs, synthesis of PCL diol-CCH, and formation of the CNC-PCL material. CNC-PCL had enhanced dispersion in the non-polar solvent chloroform owing to the well-maintained microscale size and PCL-induced hydrophobic surface. The thermal stability of CNC-PCL was largely increased due to the grafting of thermally-stable PCL. This work demonstrates that click chemistry is an attractive modification strategy to graft CNCs with polyester chains for further potential application in polymer composites. Copyright © 2018 Elsevier Ltd. All rights reserved.

Polybenzimidazole block copolymers for fuel cell: synthesis and studies of block length effects on nanophase separation, mechanical properties, and proton conductivity of PEM.

PubMed

Maity, Sudhangshu; Jana, Tushar

2014-05-14

A series of meta-polybenzimidazole-block-para-polybenzimidazole (m-PBI-b-p-PBI), segmented block copolymers of PBI, were synthesized with various structural motifs and block lengths by condensing the diamine terminated meta-PBI (m-PBI-Am) and acid terminated para-PBI (p-PBI-Ac) oligomers. NMR studies and existence of two distinct glass transition temperatures (Tg), obtained from dynamical mechanical analysis (DMA) results, unequivocally confirmed the formation of block copolymer structure through the current polymerization methodology. Appropriate and careful selection of oligomers chain length enabled us to tailor the block length of block copolymers and also to make varieties of structural motifs. Increasingly distinct Tg peaks with higher block length of segmented block structure attributed the decrease in phase mixing between the meta-PBI and para-PBI blocks, which in turn resulted into nanophase segregated domains. The proton conductivities of proton exchange membrane (PEM) developed from phosphoric acid (PA) doped block copolymer membranes were found to be increasing substantially with increasing block length of copolymers even though PA loading of these membranes did not alter appreciably with varying block length. For example when molecular weight (Mn) of blocks were increased from 1000 to 5500 then the proton conductivities at 160 °C of resulting copolymers increased from 0.05 to 0.11 S/cm. Higher block length induced nanophase separation between the blocks by creating less morphological barrier within the block which facilitated the movement of the proton in the block and hence resulting higher proton conductivity of the PEM. The structural varieties also influenced the phase separation and proton conductivity. In comparison to meta-para random copolymers reported earlier, the current meta-para segmented block copolymers were found to be more suitable for PBI-based PEM.

Tibial tunnel aperture location during single-bundle posterior cruciate ligament reconstruction: comparison of tibial guide positions.

PubMed

Shin, Young-Soo; Han, Seung-Beom; Hwang, Yeok-Ku; Suh, Dong-Won; Lee, Dae-Hee

2015-05-01

We aimed to compare posterior cruciate ligament (PCL) tibial tunnel location after tibial guide insertion medial (between the PCL remnant and the medial femoral condyle) and lateral (between the PCL remnant and the anterior cruciate ligament) to the PCL stump as determined by in vivo 3-dimensional computed tomography (3D-CT). Tibial tunnel aperture location was analyzed by immediate postoperative in vivo CT in 66 patients who underwent single-bundle PCL reconstruction, 31 by over-the-PCL and 35 by under-the-PCL tibial guide insertion techniques. Tibial tunnel positions were measured in the medial to lateral and proximal to distal directions of the posterior proximal tibia. The center of the tibial tunnel aperture was located more laterally (by 2.7 mm) in the over-the-PCL group than in the under-the-PCL group (P = .040) and by a relative percentage (absolute value/tibial width) of 3.2% (P = .031). Tibial tunnel positions in the proximal to distal direction, determined by absolute value and relative percentage, were similar in the 2 groups. Tibial tunnel apertures were located more laterally after lateral-to-the-PCL tibial guide insertion than after medial-to-the-PCL tibial guide insertion. There was, however, no significant difference between these techniques in distance from the joint line to the tibial tunnel aperture. Insertion lateral to the PCL stump may result in better placement of the PCL in its anatomic footprint. Level III, retrospective comparative study. Copyright © 2015 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Enhancement of interfacial adhesion between starch and grafted poly(ε-caprolactone).

PubMed

Ortega-Toro, Rodrigo; Santagata, Gabriella; Gomez d'Ayala, Giovanna; Cerruti, Pierfrancesco; Talens Oliag, Pau; Chiralt Boix, M Amparo; Malinconico, Mario

2016-08-20

The use of a modified poly(ε-caprolactone) (gPCL) to enhance polymer miscibility in films based on thermoplastic starch (S) and poly(ε-caprolactone) is reported. PCL was functionalized by grafting with maleic anyhdride (MA) and/or glycidyl methacrylate (GMA) by reactive blending in a batch mixer. gPCL based materials were analysed in terms of their grafting degree, structural and thermal properties. Blends based on starch and PCL (wt. ratio 80:20) with including gPCL (0, 2.5 and 5wt.%), as a compatibilizer, were obtained by extrusion and compression moulding, and their structural, thermal, mechanical and barrier properties were investigated. Blends containing gPCL evidenced better interfacial adhesion between starch and PCL domains, as deduced from both structural (XRD, FTIR, SEM) and bulk properties (DSC, TGA). Moreover, grafted PCL-based compatibilizers greatly improved functional properties of S-PCL blend films, as pointed out from mechanical performance and higher barrier properties, valuable to meet the food packaging requirements. Copyright © 2016 Elsevier Ltd. All rights reserved.

The Incidence and Short Term Functional Effect of Partial PCL Release in Fixed and Mobile Bearing PCL Retaining TKA.

PubMed

Schwarzkopf, Ran; Woolwine, Spencer; Josephs, Lee; Scott, Richard D

2015-12-01

Posterior cruciate ligament (PCL) release may be required to balance the flexion gap in PCL retaining TKA. This study examines the incidence and functional consequences of PCL release in both fixed and mobile bearing TKA. A consecutive series of 1388 TKAs with 1014 fixed bearing, and 374 mobile bearing implants were reviewed for prevalence of partial PCL release, restoration of potential flexion and objective knee stability at minimum one-year follow-up. Patients receiving mobile bearing inserts were more likely to need partial PCL release (42% versus 17.5%). The occurrence of partial PCL release did not have a significant impact on knee range of motion and subjective knee stability. The need for a partial PCL release appears to be greater in mobile than in fixed bearing. Knees that required a release in both groups demonstrated no difference in restoration of flexion compared with unreleased knees and no adverse effects on flexion stability. Copyright © 2015 Elsevier Inc. All rights reserved.

Chondroitin sulfate-g-poly(ϵ-caprolactone) co-polymer aggregates as potential targeting drug carriers.

PubMed

Wang, Li-Fang; Ni, Hsiao-Chen; Lin, Chia-Chan

2012-01-01

The aim of this study is to delineate the effect of various amounts of hydrophobic polycaprolactone (PCL) grafted onto three different degrees of methacrylated chondroitin sulfate (CSMA) on chemical-physical properties. The co-polymers were prepared by reacting the modified PCL and the hydrophilic CSMA via a radical reaction (CSMA-PCL). The effect of degree of methacrylation of CSMA and feed ratio between CSMA and PCL on compositions and critical micelle concentrations was systematically studied. The PCL composition of the CSMA-PCL was characterized by (1)H-NMR and FT-IR. The hydrodynamic diameters and morphologies of CSMA-PCL micelles were studied by DLS and TEM. Critical micelle concentrations were determined using pyrene as a probe. Taking one of the CSMA-PCL micelles as an example, a cancer-mediated ligand, folic acid, was linked to the surface. The cellular uptake of the folic acid-linked CSMA-PCL in folate-receptor-overexpressing KB cells was studied by confocal laser scanning microscopy and flow cytometry.

3D printed alendronate-releasing poly(caprolactone) porous scaffolds enhance osteogenic differentiation and bone formation in rat tibial defects.

PubMed

Kim, Sung Eun; Yun, Young-Pil; Shim, Kyu-Sik; Kim, Hak-Jun; Park, Kyeongsoon; Song, Hae-Ryong

2016-09-29

The aim of this study was to evaluate the in vitro osteogenic effects and in vivo new bone formation of three-dimensional (3D) printed alendronate (Aln)-releasing poly(caprolactone) (PCL) (Aln/PCL) scaffolds in rat tibial defect models. 3D printed Aln/PCL scaffolds were fabricated via layer-by-layer deposition. The fabricated Aln/PCL scaffolds had high porosity and an interconnected pore structure and showed sustained Aln release. In vitro studies showed that MG-63 cells seeded on the Aln/PCL scaffolds displayed increased alkaline phosphatase (ALP) activity and calcium content in a dose-dependent manner when compared with cell cultures in PCL scaffolds. In addition, in vivo animal studies and histologic evaluation showed that Aln/PCL scaffolds implanted in a rat tibial defect model markedly increased new bone formation and mineralized bone tissues in a dose-dependent manner compared to PCL-only scaffolds. Our results show that 3D printed Aln/PCL scaffolds are promising templates for bone tissue engineering applications.

Psychometric Properties in Forensic Application of the Screening Version of the Psychopathy Checklist.

PubMed

Higgs, Tamsin; Tully, Ruth J; Browne, Kevin D

2018-05-01

The Psychopathy Checklist: Screening Version (PCL: SV) is a short form of the Psychopathy Checklist-Revised (PCL-R), an expert-rated assessment that measures psychopathic personality traits in research, clinical, and community settings. The PCL-R is an extensively relied upon tool in psycho-legal contexts. The screening version is also widely used; however, it has received far less empirical attention than the PCL-R. This review examines the psychometric properties of the PCL: SV, specifically in relation to forensic samples, and evaluates its comparability with the full PCL-R. Previously reported similarity in the reliability and validity of the PCL: SV as established for the PCL-R was supported through further testing in forensic samples. However, limitations in terms of available normative data are highlighted, and the review engages with wider debate concerning the measurement of psychopathy.

PCL-Based Composite Scaffold Matrices for Tissue Engineering Applications.

PubMed

Siddiqui, Nadeem; Asawa, Simran; Birru, Bhaskar; Baadhe, Ramaraju; Rao, Sreenivasa

2018-05-14

Biomaterial-based scaffolds are important cues in tissue engineering (TE) applications. Recent advances in TE have led to the development of suitable scaffold architecture for various tissue defects. In this narrative review on polycaprolactone (PCL), we have discussed in detail about the synthesis of PCL, various properties and most recent advances of using PCL and PCL blended with either natural or synthetic polymers and ceramic materials for TE applications. Further, various forms of PCL scaffolds such as porous, films and fibrous have been discussed along with the stem cells and their sources employed in various tissue repair strategies. Overall, the present review affords an insight into the properties and applications of PCL in various tissue engineering applications.

Thiolated chitosan-modified PLA-PCL-TPGS nanoparticles for oral chemotherapy of lung cancer

NASA Astrophysics Data System (ADS)

Jiang, Liqin; Li, Xuemin; Liu, Lingrong; Zhang, Qiqing

2013-02-01

Oral chemotherapy is a key step towards `chemotherapy at home', a dream of cancer patients, which will radically change the clinical practice of chemotherapy and greatly improve the quality of life of the patients. In this research, three types of nanoparticle formulation from commercial PCL and self-synthesized d-α-tocopheryl polyethylene glycol 1000 succinate (PLA-PCL-TPGS) random copolymer were prepared in this research for oral delivery of antitumor agents, including thiolated chitosan-modified PCL nanoparticles, unmodified PLA-PCL-TPGS nanoparticles, and thiolated chitosan-modified PLA-PCL-TPGS nanoparticles. Firstly, the PLA-PCL-TPGS random copolymer was synthesized and characterized. Thiolated chitosan greatly increases its mucoadhesiveness and permeation properties, thus increasing the chances of nanoparticle uptake by the gastrointestinal mucosa and improving drug absorption. The PLA-PCL-TPGS nanoparticles were found by FESEM that they are of spherical shape and around 200 nm in diameter. The surface charge of PLA-PCL-TPGS nanoparticles was reversed from anionic to cationic after thiolated chitosan modification. The thiolated chitosan-modified PLA-PCL-TPGS nanoparticles have significantly higher level of the cell uptake than that of thiolated chitosan-modified PLGA nanoparticles and unmodified PLA-PCL-TPGS nanoparticles. In vitro cell viability studies showed advantages of the thiolated chitosan-modified PLA-PCL-TPGS nanoparticles over Taxol® in terms of cytotoxicity against A549 cells. It seems that the mucoadhesive nanoparticles can increase paclitaxel transport by opening tight junctions and bypassing the efflux pump of P-glycoprotein. In conclusion, PLA-PCL-TPGS nanoparticles modified by thiolated chitosan could enhance the cellular uptake and cytotoxicity, which revealed a potential application for oral chemotherapy of lung cancer.

Thiolated chitosan-modified PLA-PCL-TPGS nanoparticles for oral chemotherapy of lung cancer

PubMed Central

2013-01-01

Oral chemotherapy is a key step towards ‘chemotherapy at home’, a dream of cancer patients, which will radically change the clinical practice of chemotherapy and greatly improve the quality of life of the patients. In this research, three types of nanoparticle formulation from commercial PCL and self-synthesized d-α-tocopheryl polyethylene glycol 1000 succinate (PLA-PCL-TPGS) random copolymer were prepared in this research for oral delivery of antitumor agents, including thiolated chitosan-modified PCL nanoparticles, unmodified PLA-PCL-TPGS nanoparticles, and thiolated chitosan-modified PLA-PCL-TPGS nanoparticles. Firstly, the PLA-PCL-TPGS random copolymer was synthesized and characterized. Thiolated chitosan greatly increases its mucoadhesiveness and permeation properties, thus increasing the chances of nanoparticle uptake by the gastrointestinal mucosa and improving drug absorption. The PLA-PCL-TPGS nanoparticles were found by FESEM that they are of spherical shape and around 200 nm in diameter. The surface charge of PLA-PCL-TPGS nanoparticles was reversed from anionic to cationic after thiolated chitosan modification. The thiolated chitosan-modified PLA-PCL-TPGS nanoparticles have significantly higher level of the cell uptake than that of thiolated chitosan-modified PLGA nanoparticles and unmodified PLA-PCL-TPGS nanoparticles. In vitro cell viability studies showed advantages of the thiolated chitosan-modified PLA-PCL-TPGS nanoparticles over Taxol® in terms of cytotoxicity against A549 cells. It seems that the mucoadhesive nanoparticles can increase paclitaxel transport by opening tight junctions and bypassing the efflux pump of P-glycoprotein. In conclusion, PLA-PCL-TPGS nanoparticles modified by thiolated chitosan could enhance the cellular uptake and cytotoxicity, which revealed a potential application for oral chemotherapy of lung cancer. PMID:23394588

Precision Extruding Deposition for Freeform Fabrication of PCL and PCL-HA Tissue Scaffolds

NASA Astrophysics Data System (ADS)

Shor, L.; Yildirim, E. D.; Güçeri, S.; Sun, W.

Computer-aided tissue engineering approach was used to develop a novel Precision Extrusion Deposition (PED) process to directly fabricate Polycaprolactone (PCL) and composite PCL/Hydroxyapatite (PCL-HA) tissue scaffolds. The process optimization was carried out to fabricate both PCL and PCL-HA (25% concentration by weight of HA) with a controlled pore size and internal pore structure of the 0°/90° pattern. Two groups of scaffolds having 60 and 70% porosity and with pore sizes of 450 and 750 microns, respectively, were evaluated for their morphology and compressive properties using Scanning Electron Microscopy (SEM) and mechanical testing. The surface modification with plasma was conducted on PCL scaffold to increase the cellular attachment and proliferation. Our results suggested that inclusion of HA significantly increased the compressive modulus from 59 to 84 MPa for 60% porous scaffolds and from 30 to 76 MPa for 70% porous scaffolds. In vitro cell-scaffolds interaction study was carried out using primary fetal bovine osteoblasts to assess the feasibility of scaffolds for bone tissue engineering application. In addition, the results in surface hydrophilicity and roughness show that plasma surface modification can increase the hydrophilicity while introducing the nano-scale surface roughness on PCL surface. The cell proliferation and differentiation were calculated by Alamar Blue assay and by determining alkaline phosphatase activity. The osteoblasts were able to migrate and proliferate over the cultured time for both PCL as well as PCL-HA scaffolds. Our study demonstrated the viability of the PED process to the fabricate PCL and PCL-HA composite scaffolds having necessary mechanical property, structural integrity, controlled pore size and pore interconnectivity desired for bone tissue engineering.

The effect of graft strength on knee laxity and graft in-situ forces after posterior cruciate ligament reconstruction.

PubMed

Lai, Yu-Shu; Chen, Wen-Chuan; Huang, Chang-Hung; Cheng, Cheng-Kung; Chan, Kam-Kong; Chang, Ting-Kuo

2015-01-01

Surgical reconstruction is generally recommended for posterior cruciate ligament (PCL) injuries; however, the use of grafts is still a controversial problem. In this study, a three-dimensional finite element model of the human tibiofemoral joint with articular cartilage layers, menisci, and four main ligaments was constructed to investigate the effects of graft strengths on knee kinematics and in-situ forces of PCL grafts. Nine different graft strengths with stiffness ranging from 0% (PCL rupture) to 200%, in increments of 25%, of an intact PCL's strength were used to simulate the PCL reconstruction. A 100 N posterior tibial drawer load was applied to the knee joint at full extension. Results revealed that the maximum posterior translation of the PCL rupture model (0% stiffness) was 6.77 mm in the medial compartment, which resulted in tibial internal rotation of about 3.01°. After PCL reconstruction with any graft strength, the laxity of the medial tibial compartment was noticeably improved. Tibial translation and rotation were similar to the intact knee after PCL reconstruction with graft strengths ranging from 75% to 125% of an intact PCL. When the graft's strength surpassed 150%, the medial tibia moved forward and external tibial rotation greatly increased. The in-situ forces generated in the PCL grafts ranged from 13.15 N to 75.82 N, depending on the stiffness. In conclusion, the strength of PCL grafts have has a noticeable effect on anterior-posterior translation of the medial tibial compartment and its in-situ force. Similar kinematic response may happen in the models when the PCL graft's strength lies between 75% and 125% of an intact PCL.

Towards ultraporous poly(L-lactide) scaffolds from quaternary immiscible polymer blends.

PubMed

Virgilio, N; Sarazin, P; Favis, B D

2010-08-01

Ultraporous poly(l-lactide) (PLLA) scaffolds were prepared by melt-processing quaternary ethylene propylene diene rubber/poly(epsilon-caprolactone)/polystyrene/poly(l-lactide) (EPDM/PCL/PS/PLLA) 45/45/5/5 %vol. polymer blends modified with a PS-b-PLLA diblock copolymer. The morphology consists of a PS+PLLA+copolymer sub-blend layer forming at the interface of the EPDM and PCL phases. Quiescent annealing and interfacial modification using the block copolymer are used to control the blend microstructure. The ultraporous structure is subsequently obtained by selectively extracting the EPDM, PS and PCL phases. The PLLA scaffolds modified with the PS-b-PLLA copolymer present themselves as fully interconnected porous networks with asymmetric channel walls, one side being smooth while the other is covered with an array of submicron-sized PLLA droplets. They are prepared with a high degree of control over the pore size, with averages ranging from 5microm to over 100microm and a specific surface from 9.1 to 23.1m(2)/g of PLLA, as annealing is carried out from 0 to 60min. The void volume reaches values as high as 95% and in all cases the shape and dimensions of the scaffolds are maintained with a high level of integrity. The proposed method represents a comprehensive approach towards the design and generation of porous PLLA scaffolds based on complex morphologies from melt-processed multiphase polymer systems. Copyright 2010 Elsevier Ltd. All rights reserved.

Synthesis, characterization and drug loading property of Monomethoxy-Poly(ethylene glycol)-Poly(ε-caprolactone)-Poly(D,L-lactide) (MPEG-PCLA) copolymers

PubMed Central

Chu, BingYang; Zhang, Lan; Qu, Ying; Chen, XiaoXin; Peng, JinRong; Huang, YiXing; Qian, ZhiYong

2016-01-01

Amphiphilic block copolymers have attracted a great deal of attention in drug delivery systems. In this work, a series of monomethoxy-poly (ethylene glycol)-poly (ε-caprolactone-co-D,L-lactide) (MPEG-PCLA) copolymers with variable composition of poly (ε-caprolactone) (PCL) and poly (D,L-lactide) (PDLLA) were prepared via ring-opening copolymerization of ε-CL and D,L-LA in the presence of MPEG and stannous octoate. The structure and molecular weight were characterized by nuclear magnetic resonance (NMR) and gel permeation chromatography (GPC). The crystallinity, hydrophilicity, thermal stability and hydrolytic degradation behavior were investigated in detail, respectively. The results showed that the prepared amphiphilic MPEG-PCLA copolymers have adjustable properties by altering the composition of PCLA, which make it convenient for clinical applications. Besides, the drug loading properties were also studied. Docetaxel (DTX) could be entrapped in MPEG-PCLA micelles with high loading capacity and encapsulation efficiency. And all lyophilized DTX-loaded MPEG-PCLA micelles except MPEG-PCL micelles were readily re-dissolved in normal saline at 25 °C. In addition, DTX-loaded MPEG-PCLA micelles showed a slightly enhanced antitumor activity compared with free DTX. Furthermore, DTX micelles exhibited a slower and sustained release behavior in vitro, and higher DTX concentration and longer retention time in vivo. The results suggested that the MPEG-PCLA copolymer with the adjustable ratio of PCL to PDLLA may be a promising drug delivery carrier for DTX. PMID:27677842

Selective laser sintering fabrication of nano-hydroxyapatite/poly-ε-caprolactone scaffolds for bone tissue engineering applications

PubMed Central

Xia, Yan; Zhou, Panyu; Cheng, Xiaosong; Xie, Yang; Liang, Chong; Li, Chao; Xu, Shuogui

2013-01-01

The regeneration of functional tissue in osseous defects is a formidable challenge in orthopedic surgery. In the present study, a novel biomimetic composite scaffold, here called nano-hydroxyapatite (HA)/poly-ε-caprolactone (PCL) was fabricated using a selective laser sintering technique. The macrostructure, morphology, and mechanical strength of the scaffolds were characterized. Scanning electronic microscopy (SEM) showed that the nano-HA/PCL scaffolds exhibited predesigned, well-ordered macropores and interconnected micropores. The scaffolds have a range of porosity from 78.54% to 70.31%, and a corresponding compressive strength of 1.38 MPa to 3.17 MPa. Human bone marrow stromal cells were seeded onto the nano-HA/PCL or PCL scaffolds and cultured for 28 days in vitro. As indicated by the level of cell attachment and proliferation, the nano-HA/PCL showed excellent biocompatibility, comparable to that of PCL scaffolds. The hydrophilicity, mineralization, alkaline phosphatase activity, and Alizarin Red S staining indicated that the nano-HA/PCL scaffolds are more bioactive than the PCL scaffolds in vitro. Measurements of recombinant human bone morphogenetic protein-2 (rhBMP-2) release kinetics showed that after nano-HA was added, the material increased the rate of rhBMP-2 release. To investigate the in vivo biocompatibility and osteogenesis of the composite scaffolds, both nano-HA/PCL scaffolds and PCL scaffolds were implanted in rabbit femur defects for 3, 6, and 9 weeks. The wounds were studied radiographically and histologically. The in vivo results showed that both nano-HA/PCL composite scaffolds and PCL scaffolds exhibited good biocompatibility. However, the nano-HA/PCL scaffolds enhanced the efficiency of new bone formation more than PCL scaffolds and fulfilled all the basic requirements of bone tissue engineering scaffolds. Thus, they show large potential for use in orthopedic and reconstructive surgery. PMID:24204147

Conformational stability and force field of short-chain linear chlorophosphazenes: MNDO calculations, {sup 31}P NMR, vibrational spectra, and normal coordinate analyses of Cl{sub 3}PN(PCl{sub 2}N){sub n}P(O)Cl{sub 2} and [Cl{sub 3}PN(PCl{sub 2}N){sub n}PCl{sub 3}][PCl{sub 6}] (n = 1,2)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bougeard, D.; Bremard, C.; De Jaeger, R.

1992-10-29

The Raman spectra of Cl{sub 3}PN(PCl{sub 2}N){pi}P(O)Cl{sub 2} and [Cl{sub 3}PN(PCl{sub 2}N){pi}PCl{sub 3}]{sup +}PCl{sub 6}{sup {minus}} (n = 1,2) were recorded in the solid and liquid states at different temperatures. The qualitative depolarization ratios were obtained in the liquid phase. A {sup 31}P NMR study for the molecular compounds showed a coalescence phenomenon near 220 K. The potential energy around the PN bonds for the Cl{sub 3}PN(PCl{sub 2}N)P(O)Cl{sub 2} molecule and [Cl{sub 3}PN(PCl{sub 2}N){sub 2}PCl{sub 3}]{sup +} cation are derived from MNDO (modified neglect of diatomic overlap) calculations. The stable conformations are found to be trans-cis for Cl{sub 3}PN(PCl{sub 2}N)P(O)Cl{submore » 2} and [Cl{sub 3}PN(PCl{sub 2}N){sub 2}PCl{sub 3}]{sup +}. The calculated structural parameters agree well with the X-ray experimental data. The frequencies obtained by normal coordinate analysis are in good agreement with the observed ones. The MNDO calculation of the harmonic force field is in reasonable agreement with the experimental values. The force constant values assigned to torsional modes around the PN bonds correspond to low barriers for the internal rotations. The easy internal rotation around the P-N and P{double_bond}N bonds can explain the flexibility of the phosphazene backbone and the elastomeric properties of the phosphazene polymers. 46 refs., 6 figs., 3 tabs.« less

Characterization and in vitro evaluation of electrospun chitosan/polycaprolactone blend fibrous mat for skin tissue engineering.

PubMed

Prasad, Tilak; Shabeena, E A; Vinod, D; Kumary, T V; Anil Kumar, P R

2015-01-01

The electrospinning technique allows engineering biomimetic scaffolds within micro to nanoscale range mimicking natural extracellular matrix (ECM). Chitosan (CS) and polycaprolactone (PCL) were dissolved in a modified solvent mixture consisting of formic acid and acetone (3:7) and mixed in different weight ratios to get chitosan-polycaprolactone [CS-PCL] blend solutions. The CS-PCL blend polymer was electrospun in the same solvent system and compared with PCL. The physicochemical characterization of the electrospun fibrous mats was done using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), tensile test, swelling properties, water contact angle (WCA) analysis, surface profilometry and thermo gravimetric analysis (TGA). The CS-PCL fibrous mat showed decreased hydrophobicity. The CS-PCL mats also showed improved swelling property, tensile strength, thermal stability and surface roughness. The cytocompatibility of the CS-PCL and PCL fibrous mats were examined using mouse fibroblast (L-929) cell line by direct contact and cellular activity with extract of materials confirmed non-cytotoxic nature. The potential of CS-PCL and PCL fibrous mats as skin tissue engineering scaffolds were assessed by cell adhesion, viability, proliferation and actin distribution using human keratinocytes (HaCaT) and L-929 cell lines. Results indicate that CS-PCL is a better scaffold for attachment and proliferation of keratinocytes and is a potential material for skin tissue engineering.

The role of the posterior cruciate ligament in total knee replacement

PubMed Central

Ritter, M. A.; Davis, K. E.; Meding, J. B.; Farris, A.

2012-01-01

Objectives The purpose of this study was to examine the effect of posterior cruciate ligament (PCL) retention, PCL recession, and PCL excision during cruciate-retaining total knee replacement. Methods A total of 3018 anatomic graduated component total knee replacements were examined; 1846 of these retained the PCL, 455 PCLs were partially recessed, and in 717 the PCL was completely excised from the back of the tibia. Results Clinical scores between PCL groups favored excision for flexion (p < 0.0001), and recession and retention for stairs (p < 0.0001). There was a mild difference in long-term all-cause aseptic survivorship between PCL-retained (96.4% at 15 years) combined with PCL-recessed groups (96.6% at 15 years) when compared with the PCL-excised group (95.0% at 15 years) (p = 0.0411, Wilcoxon; p = 0.0042, log-rank), as well as tibial or femoral loosening, which reported prosthesis survival of 97.8% at 15 years for PCL-retained knees, 98.2% for recessed knees, and 96.4% for excised knees (p = 0.0934, Wilcoxon; p = 0.0202, log-rank). Conclusions Despite some trade off in clinical performance, if the PCL is detached at the time of operation, conversion to a posterior-stabilised prosthesis may not be necessarily required as long as stability in the anteroposterior and coronal planes is achieved. PMID:23610673

The Osteogenesis of Bone Marrow Stem Cells on mPEG-PCL-mPEG/Hydroxyapatite Composite Scaffold via Solid Freeform Fabrication

PubMed Central

Liao, Han-Tsung; Jiang, Cho-Pei

2014-01-01

The study described a novel bone tissue scaffold fabricated by computer-aided, air pressure-aided deposition system to control the macro- and microstructure precisely. The porcine bone marrow stem cells (PBMSCs) seeded on either mPEG-PCL-mPEG (PCL) or mPEG-PCL-mPEG/hydroxyapatite (PCL/HA) composite scaffold were cultured under osteogenic medium to test the ability of osteogenesis in vitro. The experimental outcomes indicated that both scaffolds possessed adequate pore size, porosity, and hydrophilicity for the attachment and proliferation of PBMSCs and the PBMSCs expressed upregulated genes of osteogensis and angiogenesis in similar manner on both scaffolds. The major differences between these two types of the scaffolds were the addition of HA leading to higher hardness of PCL/HA scaffold, cell proliferation, and VEGF gene expression in PCL/HA scaffold. However, the in vivo bone forming efficacy between PBMSCs seeded PCL and PCL/HA scaffold was different from the in vitro results. The outcome indicated that the PCL/HA scaffold which had bone-mimetic environment due to the addition of HA resulted in better bone regeneration and mechanical strength than those of PCL scaffold. Therefore, providing a bone-mimetic scaffold is another crucial factor for bone tissue engineering in addition to the biocompatibility, 3D architecture with high porosity, and interpored connection. PMID:24868523

Fabrication of hydroxyapatite-poly(epsilon-caprolactone) scaffolds by a combination of the extrusion and bi-axial lamination processes.

PubMed

Sun, Jong-Jae; Bae, Chang-Jun; Koh, Young-Hag; Kim, Hyoun-Ee; Kim, Hae-Won

2007-06-01

Hydroxyapatite (HA)/poly(epsilon-caprolactone) (PCL) composite scaffolds were fabricated using a combination of the extrusion and bi-axial lamination processes. Firstly, HA/PCL composites with various HA contents (0, 50, 60, 70 wt%) were prepared by mixing the HA powders and the molten PCL at 100 degrees C and then extruded through an orifice with dimensions of 600 x 600 microm to produce HA/PCL composite fibers. Isobutyl methacrylate (IBMA) polymer fiber was also prepared in a similar manner for use as a fugitive material. The 3-D scaffold was then produced by the bi-axial lamination of the HA/PCL and IBMA fibers, followed by solvent leaching to remove the IBMA. It was observed that the HA/PCL composites had a superior elastic modulus and biological properties, as compared to the pure PCL. The fabricated HA/PCL scaffold showed a controlled pore structure (porosity of approximately 49% and pore size of approximately 512 microm) and excellent welding between the HA/PCL fibers, as well as a high compressive strength of approximately 7.8 MPa.

Laser Printing of PCL/Progesterone Tablets for Drug Delivery Applications in Hormone Cancer Therapy

NASA Astrophysics Data System (ADS)

Salmoria, G. V.; Klauss, P.; Kanis, L. A.

2017-09-01

In this study, polycaprolactone (PCL) and progesterone (PG) tablets were produced by selective laser sintering (SLS) using different particle sizes and laser energy. The sintered PCL/PG tablets presented uniform morphology, coalescence of particles and interconnected pores distributed in the polymeric matrix. The EDS analysis confirmed the presence of progesterone recrystallized on the surface of the porous PCL matrix. The crystallinity values for the PCL/PG tablets were lower than that for the pure PCL, suggesting the interaction of components at the molecular level. The PCL/PG tablets fabricated with small particles and high laser energy presented a higher value for the flexural modulus compared with the other specimens. The glass transition temperature (Tg) was -37 °C for the PCL/PG tablet with a high degree of sintering. The fatigue test showed that the PCL/PG blend tablets have high fatigue strength. The drug release mechanism of all tablets studied followed a zero-order kinetics, and drug release rates were dependent on sintering degree and, consequently, on matrix erosion, showing a potential application to controlled drug delivery in hormone cancer therapy.

A simple and effective method for making multipotent/multilineage scaffolds with hydrophilic nature without any postmodification/treatment.

PubMed

Vaikkath, Dhanesh; Anitha, Rakhi; Sumathy, Babitha; Nair, Prabha D

2016-05-01

A number of biodegradable and bioresorbable materials, as well as scaffold designs, have been experimentally and/or clinically studied for tissue engineering of diverse tissue types. Cell-material responses are strongly dependent on the properties of the scaffold material. In this study, scaffolds based on polycaprolactone (PCL) and PCL blended with a triblock copolymer, Polycaprolactone-polytetrahydrofuran-polycaprolactone (PCL-PTHF-PCL) at different ratios were fabricated by electrospinning. Blending and electrospinning of the triblock copolymer with PCL generated a super hydrophilic scaffold, the mechanical and biological properties of which varied with the concentration of the triblock copolymer. The hydrophilicity of the electrospun scaffolds was determined by measurement of water-air contact angle. Cellular response to the electrospun scaffolds was studied by seeding two types of cells, L929 fibroblast cell line and rat mesenchymal stem cells (RMSC). We observed that the super hydrophilicity of the material did not prevent cell adhesion, while the cell proliferation was low or negligible for scaffolds containing higher amount of PCL-PTHF-PCL. Chondrogenic differentiation of RMSC was found to be better on the PCL blend containing 10% (w/v) of PCL-PTHF-PCL than the bare PCL. Our studies indicate that the cellular response is dependent on the biomaterial composition and highlight the importance of tailoring the scaffold properties for applications in tissue engineering and regenerative medicine. Copyright © 2015 Elsevier B.V. All rights reserved.

Characterization of a Novel Subgroup of Extracellular Medium-Chain-Length Polyhydroxyalkanoate Depolymerases from Actinobacteria

PubMed Central

Gangoiti, Joana; Santos, Marta; Prieto, María Auxiliadora; de la Mata, Isabel; Llama, María J.

2012-01-01

Nineteen medium-chain-length (mcl) poly(3-hydroxyalkanoate) (PHA)-degrading microorganisms were isolated from natural sources. From them, seven Gram-positive and three Gram-negative bacteria were identified. The ability of these microorganisms to hydrolyze other biodegradable plastics, such as short-chain-length (scl) PHA, poly(ε-caprolactone) (PCL), poly(ethylene succinate) (PES), and poly(l-lactide) (PLA), has been studied. On the basis of the great ability to degrade different polyesters, Streptomyces roseolus SL3 was selected, and its extracellular depolymerase was biochemically characterized. The enzyme consisted of one polypeptide chain of 28 kDa with a pI value of 5.2. Its maximum activity was observed at pH 9.5 with chromogenic substrates. The purified enzyme hydrolyzed mcl PHA and PCL but not scl PHA, PES, and PLA. Moreover, the mcl PHA depolymerase can hydrolyze various substrates for esterases, such as tributyrin and p-nitrophenyl (pNP)-alkanoates, with its maximum activity being measured with pNP-octanoate. Interestingly, when poly(3-hydroxyoctanoate-co-3-hydroxyhexanoate [11%]) was used as the substrate, the main hydrolysis product was the monomer (R)-3-hydroxyoctanoate. In addition, the genes of several Actinobacteria strains, including S. roseolus SL3, were identified on the basis of the peptide de novo sequencing of the Streptomyces venezuelae SO1 mcl PHA depolymerase by tandem mass spectrometry. These enzymes did not show significant similarity to mcl PHA depolymerases characterized previously. Our results suggest that these distinct enzymes might represent a new subgroup of mcl PHA depolymerases. PMID:22865072

Curcumin-loaded biodegradable polymeric micelles for colon cancer therapy in vitro and in vivo

NASA Astrophysics Data System (ADS)

Gou, Maling; Men, Ke; Shi, Huashan; Xiang, Mingli; Zhang, Juan; Song, Jia; Long, Jianlin; Wan, Yang; Luo, Feng; Zhao, Xia; Qian, Zhiyong

2011-04-01

Curcumin is an effective and safe anticancer agent, but its hydrophobicity inhibits its clinical application. Nanotechnology provides an effective method to improve the water solubility of hydrophobic drug. In this work, curcumin was encapsulated into monomethoxy poly(ethylene glycol)-poly(ε-caprolactone) (MPEG-PCL) micelles through a single-step nano-precipitation method, creating curcumin-loaded MPEG-PCL (Cur/MPEG-PCL) micelles. These Cur/MPEG-PCL micelles were monodisperse (PDI = 0.097 +/- 0.011) with a mean particle size of 27.3 +/- 1.3 nm, good re-solubility after freeze-drying, an encapsulation efficiency of 99.16 +/- 1.02%, and drug loading of 12.95 +/- 0.15%. Moreover, these micelles were prepared by a simple and reproducible procedure, making them potentially suitable for scale-up. Curcumin was molecularly dispersed in the PCL core of MPEG-PCL micelles, and could be slow-released in vitro. Encapsulation of curcumin in MPEG-PCL micelles improved the t1/2 and AUC of curcuminin vivo. As well as free curcumin, Cur/MPEG-PCL micelles efficiently inhibited the angiogenesis on transgenic zebrafish model. In an alginate-encapsulated cancer cell assay, intravenous application of Cur/MPEG-PCL micelles more efficiently inhibited the tumor cell-induced angiogenesisin vivo than that of free curcumin. MPEG-PCL micelle-encapsulated curcumin maintained the cytotoxicity of curcumin on C-26 colon carcinoma cellsin vitro. Intravenous application of Cur/MPEG-PCL micelle (25 mg kg-1curcumin) inhibited the growth of subcutaneous C-26 colon carcinoma in vivo (p < 0.01), and induced a stronger anticancer effect than that of free curcumin (p < 0.05). In conclusion, Cur/MPEG-PCL micelles are an excellent intravenously injectable aqueous formulation of curcumin; this formulation can inhibit the growth of colon carcinoma through inhibiting angiogenesis and directly killing cancer cells.

The Effect of Graft Strength on Knee Laxity and Graft In-Situ Forces after Posterior Cruciate Ligament Reconstruction

PubMed Central

Lai, Yu-Shu; Chen, Wen-Chuan; Huang, Chang-Hung; Cheng, Cheng-Kung; Chan, Kam-Kong; Chang, Ting-Kuo

2015-01-01

Surgical reconstruction is generally recommended for posterior cruciate ligament (PCL) injuries; however, the use of grafts is still a controversial problem. In this study, a three-dimensional finite element model of the human tibiofemoral joint with articular cartilage layers, menisci, and four main ligaments was constructed to investigate the effects of graft strengths on knee kinematics and in-situ forces of PCL grafts. Nine different graft strengths with stiffness ranging from 0% (PCL rupture) to 200%, in increments of 25%, of an intact PCL’s strength were used to simulate the PCL reconstruction. A 100 N posterior tibial drawer load was applied to the knee joint at full extension. Results revealed that the maximum posterior translation of the PCL rupture model (0% stiffness) was 6.77 mm in the medial compartment, which resulted in tibial internal rotation of about 3.01°. After PCL reconstruction with any graft strength, the laxity of the medial tibial compartment was noticeably improved. Tibial translation and rotation were similar to the intact knee after PCL reconstruction with graft strengths ranging from 75% to 125% of an intact PCL. When the graft’s strength surpassed 150%, the medial tibia moved forward and external tibial rotation greatly increased. The in-situ forces generated in the PCL grafts ranged from 13.15 N to 75.82 N, depending on the stiffness. In conclusion, the strength of PCL grafts have has a noticeable effect on anterior-posterior translation of the medial tibial compartment and its in-situ force. Similar kinematic response may happen in the models when the PCL graft’s strength lies between 75% and 125% of an intact PCL. PMID:26001045

Acute posterior cruciate ligament injuries: effect of location, severity, and associated injuries on surgical management.

PubMed

Anderson, Mark A; Simeone, F Joseph; Palmer, William E; Chang, Connie Y

2018-06-01

To correlate MRI findings of patients with posterior cruciate ligament (PCL) injury and surgical management. A retrospective search yielded 79 acute PCL injuries (36 ± 16 years old, 21 F, 58 M). Two independent readers graded PCL tear location (proximal, middle, or distal third) and severity (low-grade or high-grade partial/complete) and evaluated injury of other knee structures. When available, operative reports were examined and the performed surgical procedure was compared with injury grade, location, and presence of associated injuries. The most commonly injured knee structures in acute PCL tears were posterolateral corner (58/79, 73%) and anterior cruciate ligament (ACL) (48/79, 61%). Of the 64 patients with treatment information, 31/64 (48%) were managed surgically: 12/31 (39%) had PCL reconstruction, 13/31 (42%) had ACL reconstruction, 10/31 (32%) had posterolateral corner reconstruction, 9/31 (29%) had LCL reconstruction, 8/31 (26%) had meniscectomy, and 8/31 (26%) had fixation of a fracture. Proximal third PCL tear and multiligamentous injury were more commonly associated with surgical management (P < 0.05). Posterolateral and posteromedial corner, ACL, collateral ligament, meniscus, patellar retinaculum, and gastrocnemius muscle injury, and fracture were more likely to result in surgical management (P < 0.05). Patients with high-grade partial/complete PCL tear were more likely to have PCL reconstruction as a portion of surgical management (P < 0.05). Location of PCL tear and presence of other knee injuries were associated with surgical management while high-grade/complete PCL tear grade was associated with PCL reconstruction. MRI reporting of PCL tear location, severity, and of other knee structure injuries is important for guiding clinical management.

Osteoinduction and proliferation of bone-marrow stromal cells in three-dimensional poly (ε-caprolactone)/ hydroxyapatite/collagen scaffolds.

PubMed

Wang, Ting; Yang, Xiaoyan; Qi, Xin; Jiang, Chaoyin

2015-05-08

Osteoinduction and proliferation of bone-marrow stromal cells (BMSCs) in three-dimensional (3D) poly(ε-caprolactone) (PCL) scaffolds have not been studied throughly and are technically challenging. This study aimed to optimize nanocomposites of 3D PCL scaffolds to provide superior adhesion, proliferation and differentiation environment for BMSCs in this scenario. BMSCs were isolated and cultured in a novel 3D tissue culture poly(ε-caprolactone) (PCL) scaffold coated with poly-lysine, hydroxyapatite (HAp), collagen and HAp/collagen. Cell morphology was observed and BMSC biomarkers for osteogenesis, osteoblast differentiation and activation were analyzed. Scanning Electron Microscope (SEM) micrographs showed that coating materials were uniformly deposited on the surface of PCL scaffolds and BMSCs grew and aggregated to form clusters during 3D culture. Both mRNA and protein levels of the key players of osteogenesis and osteoblast differentiation and activation, including runt-related transcription factor 2 (Runx2), alkaline phosphates (ALP), osterix, osteocalcin, and RANKL, were significantly higher in BMSCs seeded in PCL scaffolds coated with HAp or HAp/collagen than those seeded in uncoated PCL scaffolds, whereas the expression levels were not significantly different in collagen or poly-lysine coated PCL scaffolds. In addition, poly-lysine, collagen, HAp/collagen, and HAp coated PCL scaffolds had significantly more viable cells than uncoated PCL scaffolds, especially scaffolds with HAp/collagen and collagen-alone coatings. That BMSCs in HAp or HAp/collagen PCL scaffolds had remarkably higher ALP activities than those in collagen-coated alone or uncoated PCL scaffolds indicating higher osteogenic differentiation levels of BMSCs in HAp or HAp/collagen PCL scaffolds. Moreover, morphological changes of BMSCs after four-week of 3D culture confirmed that BMSCs successfully differentiated into osteoblast with spread-out phenotype in HAp/collagen coated PCL scaffolds. This study showed a proof of concept for preparing biomimetic 3D poly (ε-caprolactone)/ hydroxyapatite/collagen scaffolds with excellent osteoinduction and proliferation capacity for bone regeneration.

Antitumor efficiency of D-alpha-tocopheryl polyethylene glycol 1000 succinate-b-poly(epsilon-caprolactone-ran-lactide) nanoparticle-based delivery of docetaxel in mice bearing cervical cancer.

PubMed

Wang, Zhongyuan; Zeng, Xiaowei; Ma, Yaping; Liu, Jian; Tang, Xiaolong; Gao, Yongfeng; Liu, Kewei; Zhang, Jinxie; Ming, Pinghong; Huang, Laiqiang; Mei, Lin

2014-08-01

Pharmaceutical nanotechnology holds potential in cancer chemotherapy. In this research, the docetaxel-loaded D-alpha-tocopheryl polyethylene glycol 1000 succinate-b-poly(epsilon-caprolactone-ran-lactide) (TPGS-b-(PCL-ran-PLA)) nanoparticles were prepared by a modified nanoprecipitation method and then the particle size, surface morphology, nanoparticle stability, in vitro drug release and cellular uptake of nanoparticles were characterized. Finally, we evaluated the therapeutic effects of nanoparticle formulation in comparison with Taxotere both in vitro and in vivo. The size of TPGS-b-(PCL-ran-PLA) nanoparticles was about 150 nm and much smaller than PCL nanoparticles (about 185 nm) and the absolute value of zeta potential was higher than PCL nanoparticles (16.49 mV vs. 13.17 mV). FESEM images further confirmed the morphology and size of nanoparticles. The drug-loaded nanoparticles were considered to be stable, showing no change in the particle size and surface charge during three-month storage of its aqueous solution. In vitro drug release of TPGS-b-(PCL-ran-PLA) nanoparticles was much faster than PCL and PCL-TPGS nanoparticles. The cumulative drug release of docetaxel-loaded TPGS-b-(PCL-ran-PLA), PCL-TPGS, and PCL NPs were 38.00%, 34.48% and 29.04%, respectively. TPGS-b-(PCL-ran-PLA) nanoparticles showed an obvious increase of cellular uptake. Due to the advantages of TPGS-b-(PCL-ran-PLA) nanoparticles, it could achieve significantly higher level of cytotoxicity in vitro and better inhibition effect of tumor growth on xenograft BALB/c nude mice tumor model than commercial Taxotere at the same dose (1.49-fold more effective). The TPGS-b-(PCL-ran-PLA) could be used as a novel and potential biodegradable polymeric material for nanoformulation in cervical cancer chemotherapy.

Effect of Varying Posterior Cruciate Ligament (PCL) Recessions on Kinematics and Ligament Strains with Cruciate Retaining Total Knee Prostheses.

PubMed

Schwarzkopf, Ran; Laster, Scott K; Cross, Michael B; Lenz, Nathaniel M

2016-04-01

Proper ligament tension in flexion with posterior cruciate retaining (CR) total knee arthroplasty (TKA) has long been associated with clinical success. The purpose of this study was to determine the effect of varying levels of posterior cruciate ligament (PCL) release on the tibiofemoral kinematics and PCL strain. A computational analysis was performed and varying levels of PCL release were simulated. Tibiofemoral kinematics was evaluated. The maximum PCL strain was determined for each bundle to evaluate the risk of rupture based on the failure strain. The femoral AP position shifted anteriorly as the PCL stiffness was reduced. PCL strain in both bundles increased as stiffness was reduced. The model predicts that the AL bundle should not rupture for a 75% release. Risk of PM bundle rupture is greater than AL bundle. Our findings suggest that a partial PCL release impacts tibiofemoral kinematics and ligament tension and strain. The relationship is dynamic and care should be taken when seeking optimal balance intra-operatively.

Effect of testosterone incorporation on cell proliferation and differentiation for polymer-bioceramic composites.

PubMed

da Costa, Kelen Jorge Rodrigues; Passos, Joel J; Gomes, Alinne D M; Sinisterra, Rubén D; Lanza, Célia R M; Cortés, Maria Esperanza

2012-11-01

In the current study, we characterized the polycaprolactone (PCL), poly(lactic acid-co-glycolic acid) (PLGA), and biphasic calcium phosphate (BCP) composites coated with testosterone propionate (T) using Fourier transform infrared spectroscopy (FTIR) and powder X-ray diffraction (XRD). Osteoblastic cells were seeded with PCL/BCP, PCL/BCP/T, PLGA/PCL/BCP and PLGA/PCL/BCP/T scaffolds, and cell viability, proliferation, differentiation and adhesion were analyzed. The results of physic-chemical experiments showed no displacements or suppression of bands in the FTIR spectra of scaffolds. The XRD patterns of the scaffolds showed an amorphous profile. The osteoblastic cells viability and proliferation increased in the presence of composites with testosterone over 72 h, and were significantly greater when PLGA/PCL/BCP/T scaffold was tested against PCL/BCP/T. Furthermore alkaline phosphatase production was significantly greater in the same group. In conclusion, the PLGA/PCL/BCP scaffold with testosterone could be a promising option for bone tissue applications due to its biocompatibility and its stimulatory effect on cell proliferation.

Mechanical and thermal properties of promising polymer composites for food packaging applications

NASA Astrophysics Data System (ADS)

Abdellah Ali, S. F.

2016-07-01

Blending starches with biodegradable polycaprolactone (PCL) was used as a route to make processable thermoplastics. When developing biodegradable polymer composites it is important to use high concentrations of starch for legislative and cost reasons. The addition of starch has a significant effect on all physical properties including toughness, elongation at break and the rheological behaviour of the melt. To enhance the physical properties, we used cellulose acetate propionate (CAP) as a cellulose derivative with high amylase starch and PCL blends. It is suggested that the PCL/starch/CAP blends are partially miscible. It was found that the yield tensile strengths of most PCL/Starch/CAP blends were higher than that of pure PCL itself. There was a big difference between glass transition temperature values of PCL/Starch/CAP blends and the pure PCL glass transition temperature which indicates that no phase separation occurs. Addition of CAP to starch and PCL blends improved the mechanical and thermal properties even at high content of starch.

Targeting NF-kB signaling with polymeric hybrid micelles that co-deliver siRNA and dexamethasone for arthritis therapy.

PubMed

Wang, Qin; Jiang, Hao; Li, Yan; Chen, Wenfei; Li, Hanmei; Peng, Ke; Zhang, Zhirong; Sun, Xun

2017-04-01

The transcription factor NF-kB plays a pivotal role in the pathogenesis of rheumatoid arthritis. Here we attempt to slow arthritis progression by co-delivering the glucocorticoid dexamethasone (Dex) and small-interfering RNA targeting NF-kB p65 using our previously developed polymeric hybrid micelle system. These micelles contain two similar amphiphilic copolymers: polycaprolactone-polyethylenimine (PCL-PEI) and polycaprolactone-polyethyleneglycol (PCL-PEG). The hybrid micelles loaded with Dex and siRNA effectively inhibited NF-kB signaling in murine macrophages more efficiently than micelles containing either Dex or siRNA on their own. In addition, the co-delivery system was able to switch macrophages from the M1 to M2 state. Injecting hybrid micelles containing Dex and siRNA into mice with collagen-induced arthritis led the therapeutic agents to accumulate in inflamed joints and reduce inflammation, without damaging renal or liver function. Thus, blocking NF-kB activation in inflammatory tissue using micelle-based co-delivery may provide a new approach for treating inflammatory disease. Copyright © 2017 Elsevier Ltd. All rights reserved.

Epoxy/Polycaprolactone Systems with Triple-Shape Memory Effect: Electrospun Nanoweb with and without Graphene Versus Co-Continuous Morphology

PubMed Central

Fejős, Márta; Molnár, Kolos; Karger-Kocsis, József

2013-01-01

Triple-shape memory epoxy (EP)/polycaprolactone (PCL) systems (PCL content: 23 wt %) with different structures (PCL nanoweb embedded in EP matrix and EP/PCL with co-continuous phase structure) were produced. To set the two temporary shapes, the glass transition temperature (Tg) of the EP and the melting temperature (Tm) of PCL served during the shape memory cycle. An attempt was made to reinforce the PCL nanoweb by graphene nanoplatelets prior to infiltrating the nanoweb with EP through vacuum assisted resin transfer molding. Morphology was analyzed by scanning electron microscopy and Raman spectrometry. Triple-shape memory characteristics were determined by dynamic mechanical analysis in tension mode. Graphene was supposed to act also as spacer between the nanofibers, improving the quality of impregnation with EP. The EP phase related shape memory properties were similar for all systems, while those belonging to PCL phase depended on the structure. Shape fixity of PCL was better without than with graphene reinforcement. The best shape memory performance was shown by the EP/PCL with co-continuous structure. Based on Raman spectrometry results, the characteristic dimension of the related co-continuous network was below 900 nm. PMID:28788342

The Influence of the Polymer Amount on the Biological Properties of PCL/ZrO2 Hybrid Materials Synthesized via Sol-Gel Technique

PubMed Central

Tranquillo, Elisabetta; Illiano, Michela; Sapio, Luigi; Spina, Annamaria; Naviglio, Silvio

2017-01-01

Organic/inorganic hybrid materials are attracting considerable attention in the biomedical area. The sol-gel process provides a convenient way to produce many bioactive organic–inorganic hybrids. Among those, poly(e-caprolactone)/zirconia (PCL/ZrO2) hybrids have proved to be bioactive with no toxic materials. The aim of this study was to investigate the effects of these materials on the cellular response as a function of the PCL content, in order to evaluate their potential use in the biomedical field. For this purpose, PCL/ZrO2 hybrids containing 6, 12, 24, and 50 wt % of PCL were synthesized by the sol-gel method. The effects of their presence on the NIH-3T3 fibroblast cell line carrying out direct cell number counting, MTT, cell damage assays, flow cytometry-based analysis of cell-cycle progression, and immunoblotting experiments. The results confirm and extend the findings that PCL/ZrO2 hybrids are free from toxicity. The hybrids containing 12 and 24 wt % PCL, (more than 6 and 50 wt % ones) enhance cell proliferation when compared to pure ZrO2 by affecting cell cycle progression. The finding that the content of PCL in PCL/ZrO2 hybrids differently supports cell proliferation suggests that PCL/ZrO2 hybrids could be useful tools with different potential clinical applications. PMID:29039803

Development of core-shell coaxially electrospun composite PCL/chitosan scaffolds.

PubMed

Surucu, Seda; Turkoglu Sasmazel, Hilal

2016-11-01

This study was related to combining of synthetic Poly (ε-caprolactone) (PCL) and natural chitosan polymers to develop three dimensional (3D) PCL/chitosan core-shell scaffolds for tissue engineering applications. The scaffolds were fabricated with coaxial electrospinning technique and the characterizations of the samples were done by thickness and contact angle (CA) measurements, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-Ray Photoelectron Spectroscopy (XPS) analyses, mechanical and PBS absorption and shrinkage tests. The average inter-fiber diameter values were calculated for PCL (0.717±0.001μm), chitosan (0.660±0.007μm) and PCL/chitosan core-shell scaffolds (0.412±0.003μm), also the average inter-fiber pore size values exhibited decreases of 66.91% and 61.90% for the PCL and chitosan scaffolds respectively, compared to PCL/chitosan core-shell ones. XPS analysis of the PCL/chitosan core-shell structures exhibited the characteristic peaks of PCL and chitosan polymers. The cell culture studies (MTT assay, Confocal Laser Scanning Microscope (CLSM) and SEM analyses) carried out with L929 ATCC CCL-1 mouse fibroblast cell line proved that the biocompatibility performance of the scaffolds. The obtained results showed that the created micro/nano fibrous structure of the PCL/chitosan core-shell scaffolds in this study increased the cell viability and proliferation on/within scaffolds. Copyright © 2016 Elsevier B.V. All rights reserved.

Functionalized hybrid nanofibers to mimic native ECM for tissue engineering applications

NASA Astrophysics Data System (ADS)

Karuppuswamy, Priyadharsini; Venugopal, Jayarama Reddy; Navaneethan, Balchandar; Laiva, Ashang Luwang; Sridhar, Sreepathy; Ramakrishna, Seeram

2014-12-01

Nanotechnology being one of the most promising technologies today shows an extremely huge potential in the field of tissue engineering to mimic the porous topography of natural extracellular matrix (ECM). Natural polymers are incorporated into the synthetic polymers to fabricate functionalized hybrid nanofibrous scaffolds, which improve cell and tissue compatibility. The present study identified the biopolymers - aloe vera, silk fibroin and curcumin incorporated into polycaprolactone (PCL) as suitable substrates for tissue engineering. Different combinations of PCL with natural polymers - PCL/aloe vera, PCL/silk fibroin, PCL/aloe vera/silk fibroin, PCL/aloe vera/silk fibroin/curcumin were electrospun into nanofibrous scaffolds. The fabricated two dimensional nanofibrous scaffolds showed high surface area, appropriate mechanical properties, hydrophilicity and porosity, required for the regeneration of diseased tissues. The nanofibrous scaffolds were characterized by Scanning electron microscope (SEM), porometry, Instron tensile tester, VCA optima contact angle measurement and FTIR to analyze the fiber diameter and morphology, porosity and pore size distribution, mechanical strength, wettability, chemical bonds and functional groups, respectively. The average fiber diameter of obtained fibers ranged from 250 nm to 350 nm and the tensile strength of PCL scaffolds at 4.49 MPa increased upto 8.3 MPa for PCL/silk fibroin scaffolds. Hydrophobicity of PCL decreased with the incorporation of natural polymers, especially for PCL/aloe vera scaffolds. The properties of as-spun nanofiber scaffolds showed their potential as promising scaffold materials in tissue engineering applications.

Influence of electrospun scaffolds prepared from distinct polymers on proliferation and viability of endothelial cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matveeva, V. G., E-mail: matveeva-vg@mail.ru; Antonova, L. V., E-mail: antonova.la@mail.ru; Velikanova, E. A.

We compared electrospun nonwoven scaffolds from polylactic acid (PLA), polycaprolactone (PCL), and polyhydroxybutyrate/valerate (PHBV)/polycaprolactone (PHBV/PCL). The surface of PHBV/PCL and PCL scaffolds was highly porous and consisted of randomly distributed fibers, whilst the surface of PLA scaffolds consisted of thin straight fibers, which located more sparsely, forming large pores. Culture of EA.hy 926 endothelial cells on these scaffolds during 7 days and further fluorescent microscopy demonstrated that the surface of PHBV/PCL scaffolds was most favorable for efficient adhesion, proliferation, and viability of endothelial cells. The lowest proliferation rate and cell viability were detected on PLA scaffolds. Therefore, PHBV/PCL electrospun nonwovenmore » scaffolds demonstrated the best results regarding endothelial cell proliferation and viability as compared to PCL and PLA scaffolds.« less

Concurrent Validity of the Psychopathic Personality Inventory with Offender and Community Samples

PubMed Central

Malterer, Melanie B.; Lilienfeld, Scott O.; Neumann, Craig S.; Newman, Joseph P.

2009-01-01

The Psychopathy Checklist - Revised (PCL-R; Hare, 2003) is a frequently used and well-validated measure of psychopathy, but is relatively time-intensive and expensive to administer. The Psychopathic Personality Inventory (PPI; Lilienfeld & Andrews, 1996) is a self-report measure that provides a less time-intensive and less expensive method for identifying psychopathic individuals. Using three independent samples and two different versions of the PCL (i.e., PCL-R, PCL:SV), we evaluated the extent to which the PPI and PCL overlap in their measurement of the psychopathy construct. Across three studies, PPI total and Factor 2 scores correlated moderately to strongly with PCL total and Factor 2 scores. Results for PPI and PCL Factor 1 scores were less positive. These findings raise important questions concerning the integration of results obtained using alternative psychopathy assessments. PMID:19955107

Importance of crystallinity of anchoring block of semi-solid amphiphilic triblock copolymers in stabilization of silicone nanoemulsions.

PubMed

Le Kim, Trang Huyen; Jun, Hwiseok; Nam, Yoon Sung

2017-10-01

Polymer emulsifiers solidified at the interface between oil and water can provide exceptional dispersion stability to emulsions due to the formation of unique semi-solid interphase. Our recent works showed that the structural stability of paraffin-in-water emulsions highly depends on the oil wettability of hydrophobic block of methoxy poly(ethylene glycol)-block-poly(ε-caprolactone) (mPEG-b-PCL). Here we investigate the effects of the crystallinity of hydrophobic block of triblock copolymer-based emulsifiers, PCLL-b-PEG-b-PCLL, on the colloidal properties of silicone oil-in-water nanoemulsions. The increased ratio of l-lactide to ε-caprolactone decreases the crystallinity of the hydrophobic block, which in turn reduces the droplet size of silicone oil nanoemulsions due to the increased chain mobility at the interface. All of the prepared nanoemulsions are very stable for a month at 37°C. However, the exposure to repeated freeze-thaw cycles quickly destabilizes the nanoemulsions prepared using the polymer with the reduced crystallinity. This work demonstrates that the anchoring chain crystallization in the semi-solid interphase is critically important for the structural robustness of nanoemulsions under harsh physical stresses. Copyright © 2017 Elsevier Inc. All rights reserved.

Incorporation of ciprofloxacin/laponite in polycaprolactone electrospun nanofibers: drug release and antibacterial studies

NASA Astrophysics Data System (ADS)

Kalwar, Kaleemullah; Zhang, Xuan; Aqeel Bhutto, Muhammad; Dali, Li; Shan, Dan

2017-12-01

Electrospun nanofibers with sustained drug release are a challenge but it can be improved by using hydrophobic polymer. Polycaprolactone (PCL) is a hydrophobic and biocompatible polymer. In this work, we have proposed a drug release mechanism by preparation of ciprofloxacin (Cip)/Laponite (LAP) complex and then incorporation in PCL nanofibers through electrospinning technique. In addition, drug incorporation was confirmed by FTIR and morphology of electrospun nanofibers was revealed by SEM. Drug loading was measured by using spectrophotometer. PCL/LAP/Cip NFs proved sustained drug release as compared to PCL NFs and PCL/Cip NFs. Furthermore, PCL/LAP/Cip NFs were used as antimicrobial agent and higher effect measured.

Multiblock thermoplastic polyurethanes for biomedical and shape memory applications

NASA Astrophysics Data System (ADS)

Gu, Xinzhu

Polyurethanes are a class of polymers that are capable of tailoring the overall polymer structure and thus final properties by many factors. The great potential in tailoring polymer structures imparts PUs unique mechanical properties and good cytocompatibility, which make them good candidates for many biomedical devices. In this dissertation, three families of multiblock thermoplastic polyurethanes are synthesized and characterized for biomedical and shape memory applications. In the first case described in Chapters 2, 3 and 4, a novel family of multiblock thermoplastic polyurethanes consisting of poly(ɛ-caprolactone) (PCL) and poly(ethylene glycol) (PEG) are presented. These materials were discovered to be very durable, with strain-to-break higher than 1200%. Heat-triggered reversible plasticity shape memory (RPSM) was observed, where the highly deformed samples completely recovered their as-cast shape within one minute when heating above the transition temperature. Instead of conventional "hard" blocks, entanglements, which result from high molecular weight, served as the physical crosslinks in this system, engendering shape recovery and preventing flow. Moreover, water-triggered shape memory effect of PCL-PEG TPUs is explored, wherein water permeated into the initially oriented PEG domains, causing rapid shape recovery toward the equilibrium shape upon contact with liquid water. The recovery behavior is found to be dependent on PEG weight percentage in the copolymers. By changing the material from bulk film to electrospun fibrous mat, recovery speed was greatly accelerated. The rate of water recovery was manipulated through structural variables, including thickness of bulk film and diameter of e-spun webs. A new, yet simple shape memory cycle, "wet-fixing" is also reported, where both the fixing and recovery ratios can be greatly improved. A detailed microstructural study on one particular composition is presented, revealing the evolution of microphase morphology during the shape memory cycle. Then, in Chapter 5, the role of Polyhedral oligosilsesquioxane (POSS) in suppressing enzymatic degradation of PCL-PEG TPUs is investigated. In vitro enzymatic hydrolytic biodegradation revealed that POSS incorporation significantly suppressed degradation of PCL-PEG TPUs. All TPUs were surface-eroded by enzymatic attack in which the chemical composition and the bulk mechanical properties exhibited little changes. A surface passivation mechanism is proposed to explain the protection of POSS-containing TPUs from enzymatic degradation. Finally, Chapter 6 presents another POSS-based TPUs system with PLA-based polyol as the glassy soft block. Manipulation of the final thermal and mechanical properties is discussed in terms of different polyols and POSS used. The free recovery and the constrained recovery responses of the polymer films were demonstrated as a function of the prior "fixing" deformation temperature. In addition, this family of materials was capable of memorizing their T g., where optimal recovery breadth and recovery stress were achieved when pre-deformation occurred right at Tg.

Genetic parameters of pelt character, feed efficiency and size traits in Finnish blue fox (Vulpes lagopus).

PubMed

Kempe, R; Koskinen, N; Strandén, I

2013-12-01

Pelt character traits (size, quality, colour clarity, darkness) are important economic traits in blue fox breeding. Better feed efficiency (FE) is another economically important and new breeding goal for fur animals. The purpose of this study was to determine the correlations between pelt character traits, FE and size traits and to estimate genetic parameters for pelt character traits. Pelt size (pSIcm ) had a high positive genetic correlation with animal grading size (gSI), final body weight (BWFin), body length and daily gain (DG), and a moderate correlation with body condition score (BCS). Animal body length and BCS (describing fatness) were considered as genetically different traits. Genetic correlations between pelt quality and size traits were estimated without precision and did not differ from zero, but colour clarity (pCL) had a low antagonistic genetic correlation with FE. Pelt size and DG had a favourable genetic correlation with FE but a fairly high unfavourable genetic correlation with dry matter feed intake. The current emphasis on selection for larger animal and pelt size improves FE indirectly, but selection for larger pelt size favours fast-growing and fat individuals and simultaneously increases feed intake. The detected genetic connections between FE, size, feed intake and pCL should be taken into account in the Finnish blue fox breeding programme. © 2013 Blackwell Verlag GmbH.

Electrospun composite matrices of poly(ε-caprolactone)-montmorillonite made using tenside free Pickering emulsions.

PubMed

Samanta, Archana; Takkar, Sonam; Kulshreshtha, Ritu; Nandan, Bhanu; Srivastava, Rajiv K

2016-12-01

The production of composite electrospun matrices of poly(ε-caprolactone) (PCL) using an emulsifier-free emulsion, made with minimal organic solvent, as precursor is reported. Pickering emulsions of PCL were prepared using modified montmorillonite (MMT) clay as the stabilizer. Hydrophobic tallow group of the modified MMT clay resulted in analogous interaction of clay with oil and aqueous phase and its adsorption at the interface to provide stability to the resultant emulsion. Composite fibrous matrices of PCL and MMT were produced using electrospinning under controlled conditions. The fiber fineness was found to alter with PCL concentration and volume fraction of the aqueous and oil phases. A higher tensile strength and modulus was obtained with inclusion of MMT in PCL electrospun matrix in comparison to a matrix made using neat PCL. The presence of clay in the fibrous matrix did not change the cell proliferation efficiency in comparison to neat PCL matrix. Composite fibrous matrices of PCL/MMT bearing enhanced tensile properties may find applications in areas other than tissue engineering for example food packaging and filtration. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of sub- and supercritical CO2 treatment on the properties of Pseudomonas cepacia lipase.

PubMed

Chen, Dawei; Zhang, Houjin; Xu, Jing; Yan, Yunjun

2013-07-10

In this work, we have investigated the influences of sub- and supercritical CO2 treatment on the properties of Pseudomonas cepacia lipase (PCL), including its esterification and transesterification activities, structural changes and stability. Results demonstrated that exposure time to subcritical CO2 treatment had a negative effect on PCL transesterification activity whereas exposure time to supercritical CO2 treatment had a positive effect. But generally, most compressed treatments significantly enhanced PCL esterification activity. Conformational analysis by FT-IR and fluorescence emission spectra revealed that enhanced activities after supercritical CO2 treatment were correlated with the secondary and tertiary structural changes of PCL. Secondary structure changes also appeared to be responsible for enhancement of PCL activities by subcritical CO2 treatment. Compared to native PCL, treated PCL's esterification activity significantly decreased in hydrophilic organic media, while transesterification activity significantly increased in tert-amyl alcohol and acetone. After supercritical treatment, the thermal stability of PCL significantly decreased in esterification reactions, however, there was no significant difference in transesterification reactions. Copyright © 2013 Elsevier Inc. All rights reserved.

Dielectric Characterization of PCL-Based Thermoplastic Materials for Microwave Diagnostic and Therapeutic Applications

PubMed Central

Aguilar, Suzette M.; Shea, Jacob D.; Al-Joumayly, Mudar A.; Van Veen, Barry D.; Behdad, Nader; Hagness, Susan C.

2011-01-01

We propose the use of a polycaprolactone (PCL)-based thermoplastic mesh as a tissue-immobilization interface for microwave imaging and microwave hyperthermia treatment. An investigation of the dielectric properties of two PCL-based thermoplastic materials in the frequency range of 0.5 – 3.5 GHz is presented. The frequency-dependent dielectric constant and effective conductivity of the PCL-based thermoplastics are characterized using measurements of microstrip transmission lines fabricated on substrates comprised of the thermoplastic meshes. We also examine the impact of the presence of a PCL-based thermoplastic mesh on microwave breast imaging. We use a numerical test bed comprised of a previously reported three-dimensional anatomically realistic breast phantom and a multi-frequency microwave inverse scattering algorithm. We demonstrate that the PCL-based thermoplastic material and the assumed biocompatible medium of vegetable oil are sufficiently well matched such that the PCL layer may be neglected by the imaging solution without sacrificing imaging quality. Our results suggest that PCL-based thermoplastics are promising materials as tissue immobilization structures for microwave diagnostic and therapeutic applications. PMID:21622068

Improving anticancer activity and reducing systemic toxicity of doxorubicin by self-assembled polymeric micelles

NASA Astrophysics Data System (ADS)

Gou, MaLing; Shi, HuaShan; Guo, Gang; Men, Ke; Zhang, Juan; Zheng, Lan; Li, ZhiYong; Luo, Feng; Qian, ZhiYong; Zhao, Xia; Wei, YuQuan

2011-03-01

In an attempt to improve anticancer activity and reduce systemic toxicity of doxorubicin (Dox), we encapsulated Dox in monomethoxy poly(ethylene glycol)-poly(ɛ-caprolactone) (MPEG-PCL) micelles by a novel self-assembly procedure without using surfactants, organic solvents or vigorous stirring. These Dox encapsulated MPEG-PCL (Dox/MPEG-PCL) micelles with drug loading of 4.2% were monodisperse and ~ 20 nm in diameter. The Dox can be released from the Dox/MPEG-PCL micelles; the Dox-release at pH 5.5 was faster than that at pH 7.0. Encapsulation of Dox in MPEG-PCL micelles enhanced the cellular uptake and cytotoxicity of Dox on the C-26 colon carcinoma cell in vitro, and slowed the extravasation of Dox in the transgenic zebrafish model. Compared to free Dox, Dox/MPEG-PCL micelles were more effective in inhibiting tumor growth in the subcutaneous C-26 colon carcinoma and Lewis lung carcinoma models, and prolonging survival of mice bearing these tumors. Dox/MPEG-PCL micelles also induced lower systemic toxicity than free Dox. In conclusion, incorporation of Dox in MPEG-PCL micelles enhanced the anticancer activity and decreased the systemic toxicity of Dox; these Dox/MPEG-PCL micelles are an interesting formulation of Dox and may have potential clinical applications in cancer therapy.

Biomineralized hydroxyapatite nanoclay composite scaffolds with polycaprolactone for stem cell-based bone tissue engineering.

PubMed

Ambre, Avinash H; Katti, Dinesh R; Katti, Kalpana S

2015-06-01

Nanoclay modified with unnatural amino acid was used to design a nanoclay-hydroxyapatite (HAP) hybrid by mineralizing HAP in the nanoclay galleries mimicking biomineralization. This hybrid (in situ HAPclay) was used to fabricate polycaprolactone (PCL)/in situ HAPclay films and scaffolds for bone regeneration. Cell culture assays and imaging were used to study interactions between human mesenchymal stem cells (hMSCs) and PCL/in situ HAPclay composites (films and scaffolds). SEM imaging indicated MSC attachment, formation of mineralized extracellular (ECM) on PCL/in situ HAPclay films, and infiltration of MSCs to the interior of PCL/in situ HAPclay scaffolds. Mineralized ECM was formed by MSCs without use of osteogenic supplements. AFM imaging performed on this in vitro generated mineralized ECM on PCL/in situ HAPclay films revealed presence of components (collagen and mineral) of hierarchical organization reminiscent of natural bone. Cellular events observed during two-stage seeding experiments on PCL/in situ HAPclay films indicated similarities with events occurring during in vivo bone formation. PCL/in situ HAPclay films showed significantly increased (100-595% increase in elastic moduli) nanomechanical properties and PCL/in situ HAPclay scaffolds showed increased degradation. This work puts forth PCL/in situ HAPclay composites as viable biomaterials for bone tissue engineering. © 2014 Wiley Periodicals, Inc.

A novel strategy to improve the thermostability of Penicillium camembertii mono- and di-acylglycerol lipase.

PubMed

Liu, Yanhua; Yuan, Dongjuan; Zhao, Zexin; Lan, Dongming; Yang, Bo; Wang, Yonghua

2018-06-07

Penicillium camembertii (PCL), a mono- and di-acylglycerol lipase (DGL), has the vital potential in the oil chemistry for food industry. However, known DGLs are mesophilic enzymes which restricts its application in the industry. To improve thermostability of PCL, we used amino acid substitution by comparison of amino acids compositions of PCL and protein sequences from typical thermophilic bacteria. Then, some conservative residues around active center were avoided to mutate according to homologous alignment analyses. Furthermore, the list was narrowed down to 28 candidate mutational sites of PCL by analyzing the hydrophobic interaction of amino acids in the structure. And among them only the mutant PCL-D25R had formed an additional salt bridge between R25-D32 and increased more hydrogen bonds interaction. Therefore, mutant PCL-D25R were constructed and expressed. Thermal inactivation assay showed that the half-life of mutant PCL-D25R at 45 °C increased 4-fold compared to that of PCL-WT. Melting temperature of mutant PCL-D25R increased to 49.5 °C from 46.5 °C by fluorescence-based thermal stability assay. This study provides a valuable strategy for engineering DGL thermostability. Copyright © 2018 Elsevier Inc. All rights reserved.

Graphite nanoplatelets-modified PLA/PCL: Effect of blend ratio and nanofiller localization on structure and properties.

PubMed

Kelnar, Ivan; Kratochvíl, Jaroslav; Kaprálková, Ludmila; Zhigunov, Alexander; Nevoralová, Martina

2017-07-01

Structure and properties of poly(lactic acid) (PLA)/poly (ɛ-caprolactone) (PCL) influenced by graphite nanoplatelets (GNP) were studied in dependence on blend composition. Electron microscopy indicates predominant localization of GNP in PCL. GNP-induced changes in viscosity hinder refinement of PCL inclusions, support PCL continuity in the co-continuous system, and lead to reduction of PLA inclusions size without GNP being present at the interface in the PCL-matrix blend. Negligible differences in crystallinity of both phases indicate that mechanical behaviour is mainly influenced by reinforcement and GNP-induced changes in morphology. Addition of 5 parts of GNP leads to ~40% and ~25% increase of stiffness in the PCL- and PLA-matrix systems, respectively, whereas the reinforcing effect is practically eliminated in the co-continuous systems due to GNP-induced lower continuity of PLA which enhances toughness. Impact resistance of the 80/20 blend shows increase with 5 parts content due to synergistic effect of PCL/GNP stacks, whereas minor increase in the blend of the ductile PCL matrix with brittle PLA inclusions is caused by GNP-modification of the component parameters. Results indicate high potential of GNP in preparing biocompatible systems with wide range of structure and properties. Copyright © 2017 Elsevier Ltd. All rights reserved.

Perfluorocarbon perfused vitrectomy: animal studies.

PubMed

Quiroz-Mercado, Hugo; Suarez-Tatá, Luis; Magdalenic, Rudi; Murillo-López, Sergio; García-Aguirre, Gerardo; Guerrero-Naranjo, Jose; Rodríguez-Reyes, Abelardo A

2004-02-01

To investigate the feasibility and advantages of using perfluorocarbon liquid (PCL) perfusion to remove vitreous during suction-cutting vitrectomy in rabbit and pig eyes. Experimental study. Balanced salt solution (BSS) was replaced by PCL perfusion during experimental vitrectomy. Oxygenated or nonoxygenated PCL was used in a recycling or a nonrecycling system. Recycling was achieved by two systems: a manual recycling system or a closed-loop system. The experiments in this study consisted of: an in vitro solubility observation, safety and feasibility of vitrectomy in rabbit eyes, effectiveness of vitrectomy with equal vitrectomy time in rabbit eyes, and retinal stability and pigment and blood dispersion in porcine eyes. Toxicity was assessed by a complete ophthalmic examination, endothelial cell count, electroretinography, and histopathology. Vitreous, blood, and pigments were immiscible in PCL. Manual recycling required less amounts of PCL than nonrecycling (15 vs 25 cc). Oxygenated and nonoxygenated PCL were not toxic. Perfluorocarbon liquid infusion removed more vitreous than balanced salt solution in a 3-minute vitrectomy time using the same settings on the vitrectomy machine. The PCL infusion in porcine eyes stabilized the retina and isolated vitreous cavity from pigment and blood and maintained a clear vitreous cavity. These data indicate that perfusion of PCL can be used to remove vitreous with a suction-cutting probe in rabbit and pig eyes. Retinal stability and isolation of the vitreous cavity at the time of vitreous removal along with PCL immiscibility and its specific gravity suggest that PCL has a potential clinical use as an irrigating solution to remove vitreous.

Clinical features and outcomes of plasma cell leukemia: a single-institution experience in the era of novel agents.

PubMed

Talamo, Giampaolo; Dolloff, Nathan G; Sharma, Kamal; Zhu, Junjia; Malysz, Jozef

2012-06-26

Plasma cell leukemia (PCL) is a rare hematologic malignancy with aggressive clinical and biologic features. Data regarding its prognosis with the use of the novel agents, i.e., the immunomodulatory drugs thalidomide and lenalidomide, and the proteasome inhibitor bortezomib, are limited. We retrospectively reviewed clinical outcomes, response to therapy, and survival of 17 patients seen at the Penn State Hershey Cancer Institute since the availability of novel agents (2006-2011). Twelve patients had primary PCL (pPCL), and 5 secondary PCL (sPCL). PCL was associated with aggressive clinicobiological features, such as high-risk cytogenetics, elevated serum beta-2-microglobulin and lactate dehydrogenase, International Staging System stage III, and rapid relapse after therapy. With the use of thalidomide, lenalidomide, and bortezomib in 53%, 53%, and 88% patients, respectively, median overall survival (OS) was 18 months in the whole group (95% confidence interval, 11-21 months), and 21 and 4 months in pPCL and sPCL, respectively (P=0.015). OS was inferior to that of 313 consecutive patients with multiple myeloma (MM) treated in the same period, even when compared with a subset of 47 MM with high-risk cytogenetics. Although our data are limited by the small sample size, we conclude that novel agents may modestly improve survival in patients with PCL, when compared to historical controls. Novel therapies do not seem to overcome the negative prognosis of PCL as compared with MM.

Clinical features and outcomes of plasma cell leukemia: a single-institution experience in the era of novel agents

PubMed Central

Talamo, Giampaolo; Dolloff, Nathan G.; Sharma, Kamal; Zhu, Junjia; Malysz, Jozef

2012-01-01

Plasma cell leukemia (PCL) is a rare hematologic malignancy with aggressive clinical and biologic features. Data regarding its prognosis with the use of the novel agents, i.e., the immunomodulatory drugs thalidomide and lenalidomide, and the proteasome inhibitor bortezomib, are limited. We retrospectively reviewed clinical outcomes, response to therapy, and survival of 17 patients seen at the Penn State Hershey Cancer Institute since the availability of novel agents (2006–2011). Twelve patients had primary PCL (pPCL), and 5 secondary PCL (sPCL). PCL was associated with aggressive clinicobiological features, such as high-risk cytogenetics, elevated serum beta-2-microglobulin and lactate dehydrogenase, International Staging System stage III, and rapid relapse after therapy. With the use of thalidomide, lenalidomide, and bortezomib in 53%, 53%, and 88% patients, respectively, median overall survival (OS) was 18 months in the whole group (95% confidence interval, 11–21 months), and 21 and 4 months in pPCL and sPCL, respectively (P=0.015). OS was inferior to that of 313 consecutive patients with multiple myeloma (MM) treated in the same period, even when compared with a subset of 47 MM with high-risk cytogenetics. Although our data are limited by the small sample size, we conclude that novel agents may modestly improve survival in patients with PCL, when compared to historical controls. Novel therapies do not seem to overcome the negative prognosis of PCL as compared with MM. PMID:23087795

A Novel Docetaxel-Loaded Poly (ɛ-Caprolactone)/Pluronic F68 Nanoparticle Overcoming Multidrug Resistance for Breast Cancer Treatment

NASA Astrophysics Data System (ADS)

Mei, Lin; Zhang, Yangqing; Zheng, Yi; Tian, Ge; Song, Cunxian; Yang, Dongye; Chen, Hongli; Sun, Hongfan; Tian, Yan; Liu, Kexin; Li, Zhen; Huang, Laiqiang

2009-12-01

Multidrug resistance (MDR) in tumor cells is a significant obstacle to the success of chemotherapy in many cancers. The purpose of this research is to test the possibility of docetaxel-loaded poly (ɛ-caprolactone)/Pluronic F68 (PCL/Pluronic F68) nanoparticles to overcome MDR in docetaxel-resistance human breast cancer cell line. Docetaxel-loaded nanoparticles were prepared by modified solvent displacement method using commercial PCL and self-synthesized PCL/Pluronic F68, respectively. PCL/Pluronic F68 nanoparticles were found to be of spherical shape with a rough and porous surface. The nanoparticles had an average size of around 200 nm with a narrow size distribution. The in vitro drug release profile of both nanoparticle formulations showed a biphasic release pattern. There was an increased level of uptake of PCL/Pluronic F68 nanoparticles in docetaxel-resistance human breast cancer cell line, MCF-7 TAX30, when compared with PCL nanoparticles. The cytotoxicity of PCL nanoparticles was higher than commercial Taxotere® in the MCF-7 TAX30 cell culture, but the differences were not significant ( p > 0.05). However, the PCL/Pluronic F68 nanoparticles achieved significantly higher level of cytotoxicity than both of PCL nanoparticles and Taxotere® ( p < 0.05), indicating docetaxel-loaded PCL/Pluronic F68 nanoparticles could overcome multidrug resistance in human breast cancer cells and therefore have considerable potential for treatment of breast cancer.

In-vitro biocompatibility, bioactivity, and mechanical strength of PMMA-PCL polymer containing fluorapatite and graphene oxide bone cements.

PubMed

Pahlevanzadeh, F; Bakhsheshi-Rad, H R; Hamzah, E

2018-06-01

In this study, a bone cement consisting of poly methyl methacrylate (PMMA)-poly caprolactone (PCL)-fluorapatite (FA)-graphene oxide (GO) was synthesized as bone filler for application in orthopedic surgeries. The FA and GO particulates were homogenously distributed in the PMMA-PCL polymer matrix and no defects and agglomeration were found in the PMMA-PCL/FA/GO bone cement. The in-vitro bioactivity result exhibited that addition of FA and GO to the polymer cement (PMMA-PCL) improved the apatite formation ability on the surface of polymer. The results also showed that addition of FA to the polymer bone cement escalated the compressive strength and elastic modulus while reducing elongation to 8 ± 2%. However, after addition of GO into the PMMA-PCL/FA bone cement, both compressive strength and elongation considerably increased to 101 ± 5 MPa and 35 ± 6%, respectively. Furthermore, tensile tests exhibited that inclusion of GO was favorable in improving the tensile modulus, UTS and elongation of the PMMA-PCL/FA bone cement. The cytotoxicity test pointed out that MG63 osteoblast cells viability increased to 279 ± 15% after addition of FA and GO to the PMMA-PCL polymer bone cement. The DAPI (4',6-diamidino-2-phenylindole) staining demonstrated better spreading and attachment of MG63 cells on PMMA-PCL/FA/GO surface compared to the PMMA-PCL bone cements. These results confirm the suitable mechanical properties and favorable bioactivity along with high cells viability of PMMA-PCL/FA/GO bone cement, indicating its potentials for orthopedic applications. Copyright © 2018 Elsevier Ltd. All rights reserved.

Curcumin-loaded biodegradable polymeric micelles for colon cancer therapy in vitro and in vivo.

PubMed

Gou, MaLing; Men, Ke; Shi, HuaShan; Xiang, MingLi; Zhang, Juan; Song, Jia; Long, JianLin; Wan, Yang; Luo, Feng; Zhao, Xia; Qian, ZhiYong

2011-04-01

Curcumin is an effective and safe anticancer agent, but its hydrophobicity inhibits its clinical application. Nanotechnology provides an effective method to improve the water solubility of hydrophobic drug. In this work, curcumin was encapsulated into monomethoxy poly(ethylene glycol)-poly(ε-caprolactone) (MPEG-PCL) micelles through a single-step nano-precipitation method, creating curcumin-loaded MPEG-PCL (Cur/MPEG-PCL) micelles. These Cur/MPEG-PCL micelles were monodisperse (PDI = 0.097 ± 0.011) with a mean particle size of 27.3 ± 1.3 nm, good re-solubility after freeze-drying, an encapsulation efficiency of 99.16 ± 1.02%, and drug loading of 12.95 ± 0.15%. Moreover, these micelles were prepared by a simple and reproducible procedure, making them potentially suitable for scale-up. Curcumin was molecularly dispersed in the PCL core of MPEG-PCL micelles, and could be slow-released in vitro. Encapsulation of curcumin in MPEG-PCL micelles improved the t(1/2) and AUC of curcumin in vivo. As well as free curcumin, Cur/MPEG-PCL micelles efficiently inhibited the angiogenesis on transgenic zebrafish model. In an alginate-encapsulated cancer cell assay, intravenous application of Cur/MPEG-PCL micelles more efficiently inhibited the tumor cell-induced angiogenesis in vivo than that of free curcumin. MPEG-PCL micelle-encapsulated curcumin maintained the cytotoxicity of curcumin on C-26 colon carcinoma cells in vitro. Intravenous application of Cur/MPEG-PCL micelle (25 mg kg(-1) curcumin) inhibited the growth of subcutaneous C-26 colon carcinoma in vivo (p < 0.01), and induced a stronger anticancer effect than that of free curcumin (p < 0.05). In conclusion, Cur/MPEG-PCL micelles are an excellent intravenously injectable aqueous formulation of curcumin; this formulation can inhibit the growth of colon carcinoma through inhibiting angiogenesis and directly killing cancer cells.

Design and characterization of dexamethasone-loaded poly (glycerol sebacate)-poly caprolactone/gelatin scaffold by coaxial electro spinning for soft tissue engineering.

PubMed

Nadim, Afsaneh; Khorasani, Saied Nouri; Kharaziha, Mahshid; Davoodi, Seyyed Mohammadreza

2017-09-01

The aim of this research was to fabricate dexamethasone (Dex)-loaded poly (glycerol sebacate) (PGS)-poly (caprolactone) (PCL)/gelatin (Gt) (PGS-PCL/Gt-Dex) fibrous scaffolds in the form of core/shell structure which have potential application in soft tissues. In this regard, after synthesize and characterizations of PGS, PGS-PCL and gelatin fibrous scaffolds were separately developed in order to optimize the electrospinning parameters. In the next step, coaxial electrospun fibrous scaffold of PGS-PCL/Gt fibrous scaffold with PGS-PCL as core and Gt as shell was developed and its mechanical, physical and chemical properties were characterized. Moreover, degradability, hydrophilicity and biocompatibility of PGS-PCL/Gt fibrous scaffold were evaluated. In addition, Dex was encapsulated in PGS-PCL/Gt fibrous scaffold and drug release was assessed for tissue engineering application. Results demonstrated the formation of coaxial fibrous scaffold with average porosity of 79% and average fiber size of 294nm. Moreover, PGS-PCL/Gt fibrous scaffold revealed lower elastic modulus, ultimate tensile and ultimate elongation than those of PGS-PCL scaffold and more close to mechanical properties of natural tissue. Furthermore, lower contact angle of PGS-PCL/Gt than that of PGS-PCL demonstrated improved surface hydrophilicity of scaffold. DEX release was sustained over a period time of 30days from the scaffolds via three steps consisting of an initial burst release, secondary linear phase release pattern with slower rate over 20days followed by an apparent zero-order release phase. MTT observations demonstrated that there was no evidence of toxicity in the samples with and without Dex. Our findings indicated that core/shell PGS-PCL/Gt-Dex fibrous could be used as a carrier for the sustained release of drugs relevant for tissue engineering which makes it appropriate for soft tissue engineering. Copyright © 2017 Elsevier B.V. All rights reserved.

PEG-b-PCL polymeric nano-micelle inhibits vascular angiogenesis by activating p53-dependent apoptosis in zebrafish

PubMed Central

Zhou, Tian; Dong, Qinglei; Shen, Yang; Wu, Wei; Wu, Haide; Luo, Xianglin; Liao, Xiaoling; Wang, Guixue

2016-01-01

Micro/nanoparticles could cause adverse effects on cardiovascular system and increase the risk for cardiovascular disease-related events. Nanoparticles prepared from poly(ethylene glycol) (PEG)-b-poly(ε-caprolactone) (PCL), namely PEG-b-PCL, a widely studied biodegradable copolymer, are promising carriers for the drug delivery systems. However, it is unknown whether polymeric PEG-b-PCL nano-micelles give rise to potential complications of the cardiovascular system. Zebrafish were used as an in vivo model to evaluate the effects of PEG-b-PCL nano-micelle on cardiovascular development. The results showed that PEG-b-PCL nano-micelle caused embryo mortality as well as embryonic and larval malformations in a dose-dependent manner. To determine PEG-b-PCL nano-micelle effects on embryonic angiogenesis, a critical process in zebrafish cardiovascular development, growth of intersegmental vessels (ISVs) and caudal vessels (CVs) in flk1-GFP transgenic zebrafish embryos using fluorescent stereomicroscopy were examined. The expression of fetal liver kinase 1 (flk1), an angiogenic factor, by real-time quantitative polymerase chain reaction (qPCR) and in situ whole-mount hybridization were also analyzed. PEG-b-PCL nano-micelle decreased growth of ISVs and CVs, as well as reduced flk1 expression in a concentration-dependent manner. Parallel to the inhibitory effects on angiogenesis, PEG-b-PCL nano-micelle exposure upregulated p53 pro-apoptotic pathway and induced cellular apoptosis in angiogenic regions by qPCR and terminal deoxynucleotidyl transferase dUTP nick end labeling (TUNEL) apoptosis assay. This study further showed that inhibiting p53 activity, either by pharmacological inhibitor or RNA interference, could abrogate the apoptosis and angiogenic defects caused by PEG-b-PCL nano-micelles, indicating that PEG-b-PCL nano-micelle inhibits angiogenesis by activating p53-mediated apoptosis. This study indicates that polymeric PEG-b-PCL nano-micelle could pose potential hazards to cardiovascular development. PMID:27980407

PEG-b-PCL polymeric nano-micelle inhibits vascular angiogenesis by activating p53-dependent apoptosis in zebrafish.

PubMed

Zhou, Tian; Dong, Qinglei; Shen, Yang; Wu, Wei; Wu, Haide; Luo, Xianglin; Liao, Xiaoling; Wang, Guixue

Micro/nanoparticles could cause adverse effects on cardiovascular system and increase the risk for cardiovascular disease-related events. Nanoparticles prepared from poly(ethylene glycol) (PEG)- b -poly( ε -caprolactone) (PCL), namely PEG- b -PCL, a widely studied biodegradable copolymer, are promising carriers for the drug delivery systems. However, it is unknown whether polymeric PEG- b -PCL nano-micelles give rise to potential complications of the cardiovascular system. Zebrafish were used as an in vivo model to evaluate the effects of PEG- b -PCL nano-micelle on cardiovascular development. The results showed that PEG- b -PCL nano-micelle caused embryo mortality as well as embryonic and larval malformations in a dose-dependent manner. To determine PEG- b -PCL nano-micelle effects on embryonic angiogenesis, a critical process in zebrafish cardiovascular development, growth of intersegmental vessels (ISVs) and caudal vessels (CVs) in flk1-GFP transgenic zebrafish embryos using fluorescent stereomicroscopy were examined. The expression of fetal liver kinase 1 (flk1), an angiogenic factor, by real-time quantitative polymerase chain reaction (qPCR) and in situ whole-mount hybridization were also analyzed. PEG- b -PCL nano-micelle decreased growth of ISVs and CVs, as well as reduced flk1 expression in a concentration-dependent manner. Parallel to the inhibitory effects on angiogenesis, PEG- b -PCL nano-micelle exposure upregulated p53 pro-apoptotic pathway and induced cellular apoptosis in angiogenic regions by qPCR and terminal deoxynucleotidyl transferase dUTP nick end labeling (TUNEL) apoptosis assay. This study further showed that inhibiting p53 activity, either by pharmacological inhibitor or RNA interference, could abrogate the apoptosis and angiogenic defects caused by PEG- b -PCL nano-micelles, indicating that PEG- b -PCL nano-micelle inhibits angiogenesis by activating p53-mediated apoptosis. This study indicates that polymeric PEG- b -PCL nano-micelle could pose potential hazards to cardiovascular development.

Earliest example of a giant monitor lizard (Varanus, Varanidae, Squamata).

PubMed

Conrad, Jack L; Balcarcel, Ana M; Mehling, Carl M

2012-01-01

Varanidae is a clade of tiny (<20 mm pre-caudal length [PCL]) to giant (>600 mm PCL) lizards first appearing in the Cretaceous. True monitor lizards (Varanus) are known from diagnostic remains beginning in the early Miocene (Varanus rusingensis), although extremely fragmentary remains have been suggested as indicating earlier Varanus. The paleobiogeographic history of Varanus and timing for origin of its gigantism remain uncertain. A new Varanus from the Mytilini Formation (Turolian, Miocene) of Samos, Greece is described. The holotype consists of a partial skull roof, right side of a braincase, partial posterior mandible, fragment of clavicle, and parts of six vertebrae. A cladistic analysis including 83 taxa coded for 5733 molecular and 489 morphological characters (71 previously unincluded) demonstrates that the new fossil is a nested member of an otherwise exclusively East Asian Varanus clade. The new species is the earliest-known giant (>600 mm PCL) terrestrial lizard. Importantly, this species co-existed with a diverse continental mammalian fauna. The new monitor is larger (longer) than 99% of known fossil and living lizards. Varanus includes, by far, the largest limbed squamates today. The only extant non-snake squamates that approach monitors in maximum size are the glass-snake Pseudopus and the worm-lizard Amphisbaena. Mosasauroids were larger, but exclusively marine, and occurred only during the Late Cretaceous. Large, extant, non-Varanus, lizards are limbless and/or largely isolated from mammalian competitors. By contrast, our new Varanus achieved gigantism in a continental environment populated by diverse eutherian mammal competitors.

A novel paclitaxel-loaded poly(epsilon-caprolactone)/Poloxamer 188 blend nanoparticle overcoming multidrug resistance for cancer treatment.

PubMed

Zhang, Yangqing; Tang, Lina; Sun, Leilei; Bao, Junbo; Song, Cunxian; Huang, Laiqiang; Liu, Kexin; Tian, Yan; Tian, Ge; Li, Zhen; Sun, Hongfan; Mei, Lin

2010-06-01

Multidrug resistance (MDR) of tumor cells is a major obstacle to the success of cancer chemotherapy. Poloxamers have been used in cancer therapy to overcome MDR. The objective of this research is to test the feasibility of paclitaxel-loaded poly(epsilon-caprolactone)/Poloxamer 188 (PCL/Poloxamer 188) nanoparticles to overcome MDR in a paclitaxel-resistant human breast cancer cell line. Paclitaxel-loaded nanoparticles were prepared by a water-acetone solvent displacement method using commercial PCL and self-synthesized PCL/Poloxamer 188 compound, respectively. PCL/Poloxamer 188 nanoparticles were found to be of spherical shape and tended to have a rough and porous surface. The nanoparticles had an average size of around 220nm, with a narrow size distribution. The in vitro drug release profile of both nanoparticle formulations showed a clear biphasic release pattern. There was an increased level of uptake of PCL/Poloxamer 188 nanoparticles (PPNP) in the paclitaxel-resistant human breast cancer cell line MCF-7/TAX, in comparison with PCL nanoparticles. The cytotoxicity of PCL nanoparticles was higher than commercial Taxol in the MCF-7/TAX cell culture, but the differences were not significant. However, the PCL/Poloxamer 188 nanoparticles achieved a significantly higher level of cytotoxicity than both of PCL nanoparticle formulation and Taxol(R), indicating that paclitaxel-loaded PCL/Poloxamer 188 nanoparticles could overcome MDR in human breast cancer cells and therefore could have considerable therapeutic potential for breast cancer. Copyright 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Protruding anterior medial meniscus-An indirect sign of posterior cruciate ligament deficiency.

PubMed

Parkar, Anagha P; Bleskestad, Kristiane; Løken, Susanne; Adriaensen, Miraude E A P M; Solheim, Eirik

2018-02-01

to examine if PROTruding of the Anterior Medial Meniscus (PROTAMM) could be an indirect sign of PCL deficiency by comparing PROTAMM to passive posterior tibial sagging (PSS) for chronic PCL rupture on routine MRI. Patients with PCL reconstruction between 2011 and 2016 were included in a case control study. Primarily cases with combined ACL/PCL injury were excluded. Secondary exclusion criteria were bony fractures, medial meniscus pathology and poor quality MRIs. Three (blinded) observers reviewed the pre-operative MRIs according to a pre-defined protocol. After applying the inclusion and primary exclusion criteria 16 patients were identified in the PCL rupture group. The control group consisted of 15 patients. After reviewing the MRIs, 6 were excluded due to secondary exclusion criteria. Mean PPS measured 4.8 mm (± 4.4 mm) in the PCL rupture group and 1.8 mm (±2.9 mm) in the control group, p = 0.05. Mean PROTAMM was 3.6 mm (±0.6 mm) in the PCL rupture group and 0.7 mm (±0.9 mm) in the control group, p = 0.004. We found a mean PROTAMM of 3.6 mm in patients with PCL rupture. We suggest that this sign, after knee injury in an otherwise normal medial meniscus, is a promising indirect sign of PCL deficiency compared to PPS. Implementation of this sign in clinical practice may improve the sensitivity of routine non-weight bearing MRI in identifying PCL deficient knees. Copyright © 2018 Elsevier B.V. All rights reserved.

Deposition of nanostructured fluorine-doped hydroxyapatite-polycaprolactone duplex coating to enhance the mechanical properties and corrosion resistance of Mg alloy for biomedical applications.

PubMed

Bakhsheshi-Rad, H R; Hamzah, E; Kasiri-Asgarani, M; Jabbarzare, S; Iqbal, N; Abdul Kadir, M R

2016-03-01

The present study addressed the synthesis of a bi-layered nanostructured fluorine-doped hydroxyapatite (nFHA)/polycaprolactone (PCL) coating on Mg-2Zn-3Ce alloy via a combination of electrodeposition (ED) and dip-coating methods. The nFHA/PCL composite coating is composed of a thick (70-80 μm) and porous layer of PCL that uniformly covered the thin nFHA film (8-10 μm) with nanoneedle-like microstructure and crystallite size of around 70-90 nm. Electrochemical measurements showed that the nFHA/PCL composite coating presented a high corrosion resistance (R(p)=2.9×10(3) kΩ cm(2)) and provided sufficient protection for a Mg substrate against galvanic corrosion. The mechanical integrity of the nFHA/PCL composite coatings immersed in SBF for 10 days showed higher compressive strength (34% higher) compared with the uncoated samples, indicating that composite coatings can delay the loss of compressive strength of the Mg alloy. The nFHA/PCL coating indicted better bonding strength (6.9 MPa) compared to PCL coating (2.2 MPa). Immersion tests showed that nFHA/PCL composite-coated alloy experienced much milder corrosion attack and more nucleation sites for apatite compared with the PCL coated and uncoated samples. The bi-layered nFHA/PCL coating can be a good alternative method for the control of corrosion degradation of biodegradable Mg alloy for implant applications. Copyright © 2015 Elsevier B.V. All rights reserved.

Engineering PCL/lignin nanofibers as an antioxidant scaffold for the growth of neuron and Schwann cell.

PubMed

Wang, Jing; Tian, Lingling; Luo, Baiwen; Ramakrishna, Seeram; Kai, Dan; Loh, Xian Jun; Yang, In Hong; Deen, G Roshan; Mo, Xiumei

2018-05-12

Antioxidant is critical for the successful of nerve tissue regeneration, and biomaterials with antioxidant activity might be favorable for peripheral nerve repair. Lignin, a biopolymer from wood with excellent antioxidant properties, is still "unexplored" as biomaterials. To design an antioxidative bioscaffold for nerve regeneration, here we synthesized lignin-polycaprolactone (PCL) copolymers via solvent free ring-opening polymerization (ROP). Then such lignin-PCL copolymers were incorporated with PCL and engineered into nanofibrous scaffolds for supporting the growth of neuron and Schwann cell. Our results showed that the addition of lignin-PCL enhanced the mechanical properties of PCL nanofibers and endowed them with good antioxidant properties (up to 98.3 ± 1.9% free radical inhibition within 4 h). Cell proliferation assay showed that PCL/lignin-PCL nanofibers increased cell viability compared to PCL fibers, especially after an oxidative challenge. Moreover, Schwann cells and dorsal root ganglion (DRG) neurons cultured on the nanofibers to assess their potential for nerve regeneration. These results suggested that nanofibers with lignin copolymers promoted cell proliferation of both BMSCs and Schwann cells, enhanced myelin basic protein expressions of Schwann cells and stimulated neurite outgrowth of DRG neurons. In all, these sustainable, intrinsically antioxidant nanofibers may be a potential candidate for nerve TE applications. Copyright © 2018 Elsevier B.V. All rights reserved.

Effect of environmental conditions on the mechanical properties and fungal degradation of polycaprolactone/microcrystalline cellulose/wood flour composites

Treesearch

Ronald Sabo; Liwei Jin; Nicole Stark; Rebecca E. Ibach

2013-01-01

Polycaprolactone (PCL) filled with microcrystalline cellulose (MCC), wood flour (WF), or both were characterized before and after exposure to various environmental conditions for 60 days. PCL/WF composites had the greatest tensile strength and modulus compared to neat PCL or PCL composites containing MCC. Electron microscopy indicated better adhesion between WF...

Treating acute cystitis with biodegradable micelle-encapsulated quercetin

PubMed Central

Wang, Bi Lan; Gao, Xiang; Men, Ke; Qiu, Jinfeng; Yang, Bowen; Gou, Ma Ling; Huang, Mei Juan; Huang, Ning; Qian, Zhi Yong; Zhao, Xia; Wei, Yu Quan

2012-01-01

Intravesical application of an anti-inflammatory drug is an efficient strategy for acute cystitis therapy. Quercetin (QU) is a potent anti-inflammatory agent; however, its poor water solubility restricts its clinical application. In an attempt to improve water solubility of QU, biodegradable monomethoxy poly(ethylene glycol)-poly(ɛ-caprolactone) (MPEG-PCL) micelles were used to encapsulate QU by self-assembly methods, creating QU/MPEG-PCL micelles. These QU/MPEG-PCL micelles with DL of 7% had a mean particle size of <34 nm, and could release QU for an extended period in vitro. The in vivo study indicated that intravesical application of MPEG-PCL micelles did not induce any toxicity to the bladder, and could efficiently deliver cargo to the bladder. Moreover, the therapeutic efficiency of intravesical administration of QU/MPEG-PCL micelles on acute cystitis was evaluated in vivo. Results indicated that QU/MPEG-PCL micelle treatment efficiently reduced the edema and inflammatory cell infiltration of the bladder in an Escherichia coli-induced acute cystitis model. These data suggested that MPEG-PCL micelle was a candidate intravesical drug carrier, and QU/MPEG-PCL micelles may have potential application in acute cystitis therapy. PMID:22661886

Pickering emulsions stabilized by biodegradable block copolymer micelles for controlled topical drug delivery.

PubMed

Laredj-Bourezg, Faiza; Bolzinger, Marie-Alexandrine; Pelletier, Jocelyne; Chevalier, Yves

2017-10-05

Surfactant-free biocompatible and biodegradable Pickering emulsions were investigated as vehicles for skin delivery of hydrophobic drugs. O/w emulsions of medium-chain triglyceride (MCT) oil droplets loaded with all-trans retinol as a model hydrophobic drug were stabilized by block copolymer nanoparticles: either poly(lactide)-block-poly(ethylene glycol) (PLA-b-PEG) or poly(caprolactone)-block-poly(ethylene glycol) (PCL-b-PEG). Those innovative emulsions were prepared using two different processes allowing drug loading either inside oil droplets or inside both oil droplets and non-adsorbed block copolymer nanoparticles. Skin absorption of retinol was investigated in vitro on pig skin biopsies using the Franz cell method. Supplementary experiments by confocal fluorescence microscopy allowed the visualization of skin absorption of the Nile Red dye on histological sections. Retinol and Nile Red absorption experiments showed the large accumulation of hydrophobic drugs in the stratum corneum for the Pickering emulsions compared to the surfactant-based emulsion and an oil solution. Loading drug inside both oil droplets and block copolymer nanoparticles enhanced again skin absorption of drugs, which was ascribed to the supplementary contribution of free block copolymer nanoparticles loaded with drug. Such effect allowed tuning drug delivery to skin over a wide range by means of a suitable selection of either the formulation or the drug loading process. Copyright © 2017 Elsevier B.V. All rights reserved.

On individual differences in person perception: raters' personality traits relate to their psychopathy checklist-revised scoring tendencies.

PubMed

Miller, Audrey K; Rufino, Katrina A; Boccaccini, Marcus T; Jackson, Rebecca L; Murrie, Daniel C

2011-06-01

This study investigated raters' personality traits in relation to scores they assigned to offenders using the Psychopathy Checklist-Revised (PCL-R). A total of 22 participants, including graduate students and faculty members in clinical psychology programs, completed a PCL-R training session, independently scored four criminal offenders using the PCL-R, and completed a comprehensive measure of their own personality traits. A priori hypotheses specified that raters' personality traits, and their similarity to psychopathy characteristics, would relate to raters' PCL-R scoring tendencies. As hypothesized, some raters assigned consistently higher scores on the PCL-R than others, especially on PCL-R Facets 1 and 2. Also as hypothesized, raters' scoring tendencies related to their own personality traits (e.g., higher rater Agreeableness was associated with lower PCL-R Interpersonal facet scoring). Overall, findings underscore the need for future research to examine the role of evaluator characteristics on evaluation results and the need for clinical training to address evaluators' personality influences on their ostensibly objective evaluations.

Matrigel immobilization on the shish-kebab structured poly(ɛ-caprolactone) nanofibers for skin tissue engineering

NASA Astrophysics Data System (ADS)

Jing, Xin; Mi, Hao-Yang; Peng, Xiang-Fang; Turng, Lih-Sheng

2016-03-01

Surface properties of tissue engineering scaffolds such as topography, hydrophilicity, and functional groups play a vital role in cell adhesion, migration, proliferation, and apoptosis. First, poly(ɛ-caprolactone) (PCL) shish-kebab scaffolds (PCL-SK), which feature a three-dimensional structure comprised of electrospun PCL nanofibers covered by periodic, self-induced PCL crystal lamellae on the surface, was created to mimic the nanotopography of native collagen fibrils in the extracellular matrix (ECM). Second, matrigel was covalently immobilized on the surface of alkaline hydrolyzed PCL-SK scaffolds to enhance their hydrophilicity. This combined approach not only mimics the nanotopography of native collagen fibrils, but also simulates the surface features of collagen fibrils for cell growth. To investigate the viability of such scaffolds, HEF1 fibroblast cell assays were conducted and the results revealed that the nanotopography of the PCL-SK scaffolds facilitated cell adhesion and proliferation. The matrigel functionalization on PCL-SK scaffolds further enhanced cellular response, which suggested elevated biocompatibility and greater potential for skin tissue engineering applications.

Fluorescent composite scaffolds made of nanodiamonds/polycaprolactone

NASA Astrophysics Data System (ADS)

Cao, Li; Hou, Yanwen; Lafdi, Khalid; Urmey, Kirk

2015-11-01

Polycaprolactone (PCL) has been widely studied for biological applications. Biodegradable PCL fibrous scaffold can work as an appropriate substrate for tissue regeneration. In this letter, fluorescent nanodiamonds (FNDs) were prepared after surface passivation with octadecylamine. The FNDs were then mixed with PCL polymer and subsequently electrospun into FNDs/PCL fibrous scaffolds. The obtained scaffolds not only exhibited photoluminescence, but also showed reinforced mechanical strength. Toxicity study indicated FNDs/PCL scaffolds were nontoxic. This biocompatible fluorescent composite fibrous scaffold can support in vitro cell growth and also has the potential to act as an optical probe for tissue engineering application in vitro and in vivo.

Violence Risk Assessment and Facet 4 of the Psychopathy Checklist: Predicting Institutional and Community Aggression in Two Forensic Samples

ERIC Educational Resources Information Center

Walters, Glenn D.; Heilbrun, Kirk

2010-01-01

The Psychopathy Checklist and Psychopathy Checklist-Revised (PCL/PCL-R) were used to predict institutional aggression and community violence in two groups of forensic patients. Results showed that Facet 4 (Antisocial) of the PCL/PCL-R or one of its parcels consistently achieved incremental validity relative to the first three facets, whereas the…

Microstructure and mechanical properties of biodegradable poly (D/L) lactic acid/polycaprolactone blends processed from the solvent-evaporation technique.

PubMed

Esmaeilzadeh, Javad; Hesaraki, Saeed; Hadavi, Seyed Mohammad-Mehdi; Esfandeh, Masoud; Ebrahimzadeh, Mohammad Hosein

2017-02-01

In this study, polymer blends comprising poly(D/L) lactic acid (PDLLA) and 0-30wt% polycaprolactone (PCL) was prepared by a solvent-evaporation technique. The effect of PCL content on the dynamic-mechanical properties and tensile and flexural characteristics of the blends was evaluated. The creep and stress relaxation behaviors were also determined and using various known models such as power law, Burgers model and Weibull distribution equation. The results showed that by increasing the PCL content from 10 to 30wt%, the yield stress and flexural strength decreased from 47MPa to 26MPa and 72MPa to 29MPa respectively. In addition to tensile and flexural strength, the elastic modulus of neat PDLLA declined with increasing the PCL content, whereas the elongation or the strain percentage at the break point increased considerably. Biphasic regions were observed in the microstructures of the blends, indicating the immiscibility of PCL in PDLLA matrix. However, the PCL spherulites with an average particle diameter of 100nm to 5μm were homogeneously dispersed in PDLLA phase even at high PCL concentrations. Moreover, the microstructures of the fractured surfaces of the polymers confirmed that PDLLA with a brittle fracture behavior tends toward a soft fracture behavior when it is blended with PCL. The dynamic-mechanical tests indicated that the damping energy and dissipative ability of PDLLA improve by adding PCL. Moreover, T g of neat PDLLA by adding of 10, 20 and 30wt% decreases from 67.3 to 66.2, 65.1 and 63.5°C respectively. Increasing in the recovered viscoelastic strain due to the addition of PCL was also experienced which can be attributed to the presence of large volumetric backbone of PCL chains as well as easy movement of them in the matrix. The results of modeling studies showed a good correlation between the experimentally obtained data. Copyright © 2016 Elsevier B.V. All rights reserved.

Plasma Cholesterol–Induced Lesion Networks Activated before Regression of Early, Mature, and Advanced Atherosclerosis

PubMed Central

Björkegren, Johan L. M.; Hägg, Sara; Jain, Rajeev K.; Cedergren, Cecilia; Shang, Ming-Mei; Rossignoli, Aránzazu; Takolander, Rabbe; Melander, Olle; Hamsten, Anders; Michoel, Tom; Skogsberg, Josefin

2014-01-01

Plasma cholesterol lowering (PCL) slows and sometimes prevents progression of atherosclerosis and may even lead to regression. Little is known about how molecular processes in the atherosclerotic arterial wall respond to PCL and modify responses to atherosclerosis regression. We studied atherosclerosis regression and global gene expression responses to PCL (≥80%) and to atherosclerosis regression itself in early, mature, and advanced lesions. In atherosclerotic aortic wall from Ldlr−/−Apob 100/100 Mttp flox/floxMx1-Cre mice, atherosclerosis regressed after PCL regardless of lesion stage. However, near-complete regression was observed only in mice with early lesions; mice with mature and advanced lesions were left with regression-resistant, relatively unstable plaque remnants. Atherosclerosis genes responding to PCL before regression, unlike those responding to the regression itself, were enriched in inherited risk for coronary artery disease and myocardial infarction, indicating causality. Inference of transcription factor (TF) regulatory networks of these PCL-responsive gene sets revealed largely different networks in early, mature, and advanced lesions. In early lesions, PPARG was identified as a specific master regulator of the PCL-responsive atherosclerosis TF-regulatory network, whereas in mature and advanced lesions, the specific master regulators were MLL5 and SRSF10/XRN2, respectively. In a THP-1 foam cell model of atherosclerosis regression, siRNA targeting of these master regulators activated the time-point-specific TF-regulatory networks and altered the accumulation of cholesterol esters. We conclude that PCL leads to complete atherosclerosis regression only in mice with early lesions. Identified master regulators and related PCL-responsive TF-regulatory networks will be interesting targets to enhance PCL-mediated regression of mature and advanced atherosclerotic lesions. PMID:24586211

Structure and magnetic properties of SiO{sub 2}/PCL novel sol–gel organic–inorganic hybrid materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Catauro, Michelina, E-mail: michelina.catauro@unina2.it; Bollino, Flavia; Cristina Mozzati, Maria

2013-07-15

Organic–inorganic nanocomposite materials have been synthesized via sol–gel. They consist of an inorganic SiO{sub 2} matrix, in which different percentages of poly(ε-caprolactone) (PCL) have been incorporated. The formation of H-bonds among the carbonyl groups of the polymer chains and Si–OH group of the inorganic matrix has been proved by means of Fourier transform infrared spectroscopy (FT-IR) analysis and has been confirmed by solid-state nuclear magnetic resonance (NMR). X-Ray diffraction (XRD) analysis highlighted the amorphous nature of the synthesized materials. Scanning electron microscope (SEM) micrograph and atomic force microscope (AFM) topography showed their homogeneous morphology and nanostructure nature. Considering the opportunitymore » to synthesize these hybrid materials under microgravity conditions by means of magnetic levitation, superconducting quantum interference device (SQUID) magnetometry has been used to quantify their magnetic susceptibility. This measure has shown that the SiO{sub 2}/PCL hybrid materials are diamagnetic and that their diamagnetic susceptibility is independent of temperature and increases with the PCL amount. - Graphical abstract: Characterization and magnetic properties of SiO{sub 2}/PCL organic–inorganic hybrid materials synthesized via sol–gel. FT-IR, Fourier transform infrared spectroscopy; solid-state NMR: solid-state nuclear magnetic resonance; SQUID: superconducting quantum interference device. - Highlights: • Sol–gel synthesis of SiO{sub 2}/PCL amorphous class I organic–inorganic hybrid materials. • FT-IR and NMR analyses show the hydrogen bonds formation between SiO{sub 2} and PCL. • AFM and SEM analyses confirm that the SiO{sub 2}/PCL are homogenous hybrid materials. • The SQUID measures show that the simples are diamagnetic. • Diamagnetic susceptibility of SiO{sub 2}/PCL materials increases with the PCL amount.« less

Biomimetic composite coating on rapid prototyped scaffolds for bone tissue engineering.

PubMed

Arafat, M Tarik; Lam, Christopher X F; Ekaputra, Andrew K; Wong, Siew Yee; Li, Xu; Gibson, Ian

2011-02-01

The objective of this present study was to improve the functional performance of rapid prototyped scaffolds for bone tissue engineering through biomimetic composite coating. Rapid prototyped poly(ε-caprolactone)/tri-calcium phosphate (PCL/TCP) scaffolds were fabricated using the screw extrusion system (SES). The fabricated PCL/TCP scaffolds were coated with a carbonated hydroxyapatite (CHA)-gelatin composite via biomimetic co-precipitation. The structure of the prepared CHA-gelatin composite coating was studied by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. Compressive mechanical testing revealed that the coating process did not have any detrimental effect on the mechanical properties of the scaffolds. The cell-scaffold interaction was studied by culturing porcine bone marrow stromal cells (BMSCs) on the scaffolds and assessing the proliferation and bone-related gene and protein expression capabilities of the cells. Confocal laser microscopy and SEM images of the cell-scaffold constructs showed a uniformly distributed cell sheet and accumulation of extracellular matrix in the interior of CHA-gelatin composite-coated PCL/TCP scaffolds. The proliferation rate of BMSCs on CHA-gelatin composite-coated PCL/TCP scaffolds was about 2.3 and 1.7 times higher than that on PCL/TCP scaffolds and CHA-coated PCL/TCP scaffolds, respectively, by day 10. Furthermore, reverse transcription polymerase chain reaction and Western blot analysis revealed that CHA-gelatin composite-coated PCL/TCP scaffolds stimulate osteogenic differentiation of BMSCs the most, compared with PCL/TCP scaffolds and CHA-coated PCL/TCP scaffolds. These results demonstrate that CHA-gelatin composite-coated rapid prototyped PCL/TCP scaffolds are promising for bone tissue engineering. Copyright © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Development of innovative biopolymers and related composites for bone tissue regeneration: study of their interaction with human osteoprogenitor cells.

PubMed

Basile, Maria Assunta; d'Ayala, Giovanna Gomez; Laurienzo, Paola; Malinconico, Mario; Della Ragione, Fulvio; Oliva, Adriana

2012-01-01

In the framework of a project aiming to improve the properties of poly(ε-caprolactone) (PCL)-based devices, we prepared novel composites and tested their in vitro biocompatibility and osteogenic capacity on human mesenchymal stromal cells (MSC) from bone marrow. We prepared two functionalized derivatives, PCL-g-MAGMA and PCL-g-DMAEA, by insertion of anhydride groups by radical grafting of maleic anhydride (MA) and glycidyl-methacrylate (GMA) molecules, and by insertion of N-(dimethylamino)ethylacrylate (DMAEA) of tertiary amines groups, respectively. In addition, in order to improve the osteoconductive properties of the materials, we also prepared the corresponding composites containing the mineral component of bone, namely hydroxyapatite (HA). Mesenchymal stromal cells (MSC) derived from bone marrow were prepared, plated onto a number of discs obtained from these functionalized derivatives and tested in terms of adhesion and vitality (by MTT test and SEM observation), and the expression of alkaline phosphatase, the early marker of osteoblastic phenotype. The biological in vitro assessment of the functionalized materials, PCL-g-MAGMA and PCL-g-DMAEA, appeared promising only in part, in particular the cells exhibited very poor adhesion to PCL-g-MAGMA. On the contrary, the related composites, PCL-g-MAGMA-HA and PCL-g-DMAEA-HA clearly showed that the addition of HA greatly ameliorated the cell-material interaction. In particular, a surprisingly increased response characterized PCL-g-MAGMA-HA, either in terms of adhesion and vitality or in terms of alkaline phosphatase activity. Altogether these studies showed that the addition of HA nanowhiskers resulted for all basic materials, in particular PCL-g-MAGMA, in improved cell adhesion and performance.

Rapid and low-cost hot-embossing of polycaprolactone microfluidic devices

NASA Astrophysics Data System (ADS)

Fan, Yiqiang; Liu, Shicheng; He, Jianyun; Gao, Kexin; Zhang, Yajun

2018-01-01

Polycaprolactone (PCL) is a low-cost biocompatible and biodegradable material which is highly suitable for the short-live applications like microfluidics in the biological and medical field. In this study, a rapid and low-cost microfabrication technique for PCL-based microfluidic devices is proposed, the SU-8 mold fabricated on the silicon substrate was used for the hot-embossing of microstructures on PCL. Since PCL after the molding process is optically non-transparent, to improve the visibility of the fluid in the microfluidic device and enclosing the microchannel, a transparency adhesive film which originally used for the sealing of PCR well-plate is used for the sealing of the microchannels embossed on PCL substrate. The profile of the fabricated microchannels was carefully characterized, the bonding strength is tested and several PCL-based microfluidic devices were also fabricated and tested for demonstration.

Posterior cruciate-retaining versus posterior-stabilized total knee arthroplasty for osteoarthritis with severe varus deformity.

PubMed

Ünkar, Ethem Ayhan; Öztürkmen, Yusuf; Şükür, Erhan; Çarkçı, Engin; Mert, Murat

2017-03-01

The aim of this study was to compare the radiological and functional results of posterior cruciate ligament (PCL) - retaining and posterior-stabilized total knee arthroplasties in patients with severe varus gonarthrosis. Medical records of 112 knees of 96 patients who underwent total knee arthroplasty for severe varus (≥15°) were reviewed. PCL-retaining and PCL-stabilizing groups consisted of 58 and 54 knees, respectively. Mean follow-up time was 56.6 months (range: 24-112 months). Knee Society (KS) clinical rating system was used in clinical evaluation. Range of motion, degree of flexion contracture, postoperative alignment, and complication rates were compared between the groups. Mean preoperative mechanical tibiofemoral angle was 20.1° in varus alignment, and was restored to 4.6° in valgus postoperatively. No statistically significant differences were found between PCL-stabilizing and PCL-retaining groups when KS knee scores, function scores, and flexion arc were evaluated. Two patients in PCL-retaining group underwent revision surgery due to aseptic loosening of tibial component. One patient in PCL-stabilizing group needed arthrotomy due to patellar clunk syndrome. There were no notable differences between the 2 groups and PCL-retaining design had outcomes as good as PCL-stabilizing total knee implant in osteoarthritic knees with severe varus deformity. Level III, Therapeutic study. Copyright © 2016 Turkish Association of Orthopaedics and Traumatology. Production and hosting by Elsevier B.V. All rights reserved.

Efficacy of rhBMP-2 Loaded PCL/β-TCP/bdECM Scaffold Fabricated by 3D Printing Technology on Bone Regeneration.

PubMed

Bae, Eun-Bin; Park, Keun-Ho; Shim, Jin-Hyung; Chung, Ho-Yun; Choi, Jae-Won; Lee, Jin-Ju; Kim, Chang-Hwan; Jeon, Ho-Jun; Kang, Seong-Soo; Huh, Jung-Bo

2018-01-01

This study was undertaken to evaluate the effect of 3D printed polycaprolactone (PCL)/ β -tricalcium phosphate ( β -TCP) scaffold containing bone demineralized and decellularized extracellular matrix (bdECM) and human recombinant bone morphogenetic protein-2 (rhBMP-2) on bone regeneration. Scaffolds were divided into PCL/ β -TCP, PCL/ β -TCP/bdECM, and PCL/ β -TCP/bdECM/BMP groups. In vitro release kinetics of rhBMP-2 were determined with respect to cell proliferation and osteogenic differentiation. These three reconstructive materials were implanted into 8 mm diameter calvarial bone defect in male Sprague-Dawley rats. Animals were sacrificed four weeks after implantation for micro-CT, histologic, and histomorphometric analyses. The findings obtained were used to calculate new bone volumes (mm 3 ) and new bone areas (%). Excellent cell bioactivity was observed in the PCL/ β -TCP/bdECM and PCL/ β -TCP/bdECM/BMP groups, and new bone volume and area were significantly higher in the PCL/ β -TCP/bdECM/BMP group than in the other groups ( p < .05). Within the limitations of this study, bdECM printed PCL/ β -TCP scaffolds can reproduce microenvironment for cells and promote adhering and proliferating the cells onto scaffolds. Furthermore, in the rat calvarial defect model, the scaffold which printed rhBMP-2 loaded bdECM stably carries rhBMP-2 and enhances bone regeneration confirming the possibility of bdECM as rhBMP-2 carrier.

Biofunctionalization of PAMAM-montmorillonite decorated poly (Ɛ-caprolactone)-chitosan electrospun nanofibers for cell adhesion and electrochemical cytosensing.

PubMed

Kirbay, Fatma Ozturk; Yalcinkaya, Esra Evrim; Atik, Gozde; Evren, Gizem; Unal, Betul; Demirkol, Dilek Odaci; Timur, Suna

2018-06-30

The construction and biofunctionalization of the poly (Ɛ-caprolactone) (PCL)-chitosan (CHIT) nanofibrous mats, which included Polyamidoamine (PAMAM) dendrimer modified montmorillonite (Mt), for the cell adhesion and electrochemical cytosensing were accomplished in this report. After the intercalation of the PAMAM generation zero dendrimer into the Mt, PAMAM-Mt decorated PCL-CHIT electrospun nanofibers were formed. The addition of PAMAM caused the decrease of contact angle of PCL-CHIT nanofibers. The covalent immobilization of a tripeptide namely Arginylglycylaspartate (RGD) on both the PCL-CHIT/Mt and PCL-CHIT/PAMAM-Mt surface was carried out. U87-MG and HaCaT (negative control) cell lines were incubated on the PCL-CHIT/Mt/RGD and PCL-CHIT/PAMAM-Mt/RGD. The proliferation studies and imaging of the cells were carried out on these fibers. Finally, electrochemical measurements were performed after each modification step by differential pulse/cyclic voltammetry and electrochemical impedance spectroscopy. U87-MG cells were grown better than HaCaT cells on the PCL-CHIT/PAMAM-Mt/RGD surfaces. To the best of our knowledge, there is no study that developed electrochemical cytosensor using electrospun nanofibers as a cell adhesion platform. Copyright © 2018 Elsevier B.V. All rights reserved.

MRI appearance of posterior cruciate ligament tears.

PubMed

Rodriguez, William; Vinson, Emily N; Helms, Clyde A; Toth, Alison P

2008-10-01

There is little in the radiology literature regarding the MRI appearance of a torn posterior cruciate ligament (PCL). The purpose of this study was to describe the MRI appearance of surgically proven PCL tears and to emphasize previously unreported signs. The PCL is usually injured as the result of stretching deformation; on MRI, the ligament maintains continuity as a single structure with apparent thickening. On sagittal T2-weighted images, an anteroposterior diameter of 7 mm or more is highly suggestive of a torn PCL. Increased intrasubstance signal intensity in the PCL on proton-density images with lower signal intensity on T2-weighted images is another common feature.

Optimal Hydrophobicity in Ring-Opening Metathesis Polymerization-Based Protein Mimics Required for siRNA Internalization.

PubMed

deRonde, Brittany M; Posey, Nicholas D; Otter, Ronja; Caffrey, Leah M; Minter, Lisa M; Tew, Gregory N

2016-06-13

Exploring the role of polymer structure for the internalization of biologically relevant cargo, specifically siRNA, is of critical importance to the development of improved delivery reagents. Herein, we report guanidinium-rich protein transduction domain mimics (PTDMs) based on a ring-opening metathesis polymerization scaffold containing tunable hydrophobic moieties that promote siRNA internalization. Structure-activity relationships using Jurkat T cells and HeLa cells were explored to determine how the length of the hydrophobic block and the hydrophobic side chain compositions of these PTDMs impacted siRNA internalization. To explore the hydrophobic block length, two different series of diblock copolymers were synthesized: one series with symmetric block lengths and one with asymmetric block lengths. At similar cationic block lengths, asymmetric and symmetric PTDMs promoted siRNA internalization in the same percentages of the cell population regardless of the hydrophobic block length; however, with 20 repeat units of cationic charge, the asymmetric block length had greater siRNA internalization, highlighting the nontrivial relationships between hydrophobicity and overall cationic charge. To further probe how the hydrophobic side chains impacted siRNA internalization, an additional series of asymmetric PTDMs was synthesized that featured a fixed hydrophobic block length of five repeat units that contained either dimethyl (dMe), methyl phenyl (MePh), or diphenyl (dPh) side chains and varied cationic block lengths. This series was further expanded to incorporate hydrophobic blocks consisting of diethyl (dEt), diisobutyl (diBu), and dicyclohexyl (dCy) based repeat units to better define the hydrophobic window for which our PTDMs had optimal activity. High-performance liquid chromatography retention times quantified the relative hydrophobicities of the noncationic building blocks. PTDMs containing the MePh, diBu, and dPh hydrophobic blocks were shown to have superior siRNA internalization capabilities compared to their more and less hydrophobic counterparts, demonstrating a critical window of relative hydrophobicity for optimal internalization. This better understanding of how hydrophobicity impacts PTDM-induced internalization efficiencies will help guide the development of future delivery reagents.

Matrigel immobilization on the shish-kebab structured poly(ε-caprolactone) nanofibers for skin tissue engineering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jing, Xin, E-mail: jingxinscut@gmail.com; Mi, Hao-Yang; Wisconsin Institutes for Discovery, University of Wisconsin-Madison, 53715

Surface properties of tissue engineering scaffolds such as topography, hydrophilicity, and functional groups play a vital role in cell adhesion, migration, proliferation, and apoptosis. First, poly(ε-caprolactone) (PCL) shish-kebab scaffolds (PCL-SK), which feature a three-dimensional structure comprised of electrospun PCL nanofibers covered by periodic, self-induced PCL crystal lamellae on the surface, was created to mimic the nanotopography of native collagen fibrils in the extracellular matrix (ECM). Second, matrigel was covalently immobilized on the surface of alkaline hydrolyzed PCL-SK scaffolds to enhance their hydrophilicity. This combined approach not only mimics the nanotopography of native collagen fibrils, but also simulates the surface featuresmore » of collagen fibrils for cell growth. To investigate the viability of such scaffolds, HEF1 fibroblast cell assays were conducted and the results revealed that the nanotopography of the PCL-SK scaffolds facilitated cell adhesion and proliferation. The matrigel functionalization on PCL-SK scaffolds further enhanced cellular response, which suggested elevated biocompatibility and greater potential for skin tissue engineering applications.« less

Design and characterization of a conductive nanostructured polypyrrole-polycaprolactone coated magnesium/PLGA composite for tissue engineering scaffolds.

PubMed

Liu, Haixia; Wang, Ran; Chu, Henry K; Sun, Dong

2015-09-01

A novel biodegradable and conductive composite consisting of magnesium (Mg), polypyrrole-block-ploycaprolactone (PPy-PCL), and poly(lactic-co-glycolic acid) (PLGA) is synthesized in a core-shell-skeleton manner for tissue engineering applications. Mg particles in the composite are first coated with a conductive nanostructured PPy-PCL layer for corrosion resistance via the UV-induced photopolymerization method. PLGA matrix is then added to tailor the biodegradability of the resultant composite. Composites with different composition ratios are examined through experiments, and their material properties are characterized. The in vitro experiments on culture of 293FT-GFP cells show that the composites are suitable for cell growth and culture. Biodegradability of the composite is also evaluated. By adding PLGA matrix to the composite, the degrading time of the composite can last for more than eight weeks, hence providing a longer period for tissue formation as compared to Mg composites or alloys. The findings of this research will offer a new opportunity to utilize a conductive, nanostructured-coated Mg/PLGA composite as the scaffold material for implants and tissue regeneration. © 2015 Wiley Periodicals, Inc.

pH-Dependent, Thermosensitive Polymeric Nanocarriers for Drug Delivery to Solid Tumors

PubMed Central

Chen, Ching-Yi; Kim, Tae Hee; Wu, Wen-Chung; Huang, Chi-Ming; Wei, Hua; Mount, Christopher W.; Tian, Yanqing; Jang, Sei-Hum; Pun, Suzie H.; Jen, Alex K-Y

2013-01-01

Polymeric micelles are promising carriers for anticancer agents due to their small size, ease of assembly, and versatility for functionalization. A current challenge in the use of polymeric micelles is the sensitive balance that must be achieved between stability during prolonged blood circulation and release of active drug at the tumor site. Stimuli-responsive materials provide a mechanism for triggered drug release in the acidic tumor and intracellular microenvironments. In this work, we synthesized a series of dual pH- and temperature-responsive block copolymers containing a poly(ε-caprolactone) (PCL) hydrophobic block with a poly(triethylene glycol) block that were copolymerized with an amino acid-functionalized monomer. The block copolymers formed micellar structures in aqueous solutions. An optimized polymer that was functionalized with 6-aminocaproic acid (ACA) possessed pH-sensitive phase transitions at mildly acidic pH and body temperature. Doxorubicin-loaded micelles formed from these polymers were stable at blood pH (~7.4) and showed increased drug release at acidic pH. In addition, these micelles displayed more potent anti-cancer activity than free doxorubicin when tested in a tumor xenograft model in mice. PMID:23498892

Harmonic Series Meets Fibonacci Sequence

ERIC Educational Resources Information Center

Chen, Hongwei; Kennedy, Chris

2012-01-01

The terms of a conditionally convergent series may be rearranged to converge to any prescribed real value. What if the harmonic series is grouped into Fibonacci length blocks? Or the harmonic series is arranged in alternating Fibonacci length blocks? Or rearranged and alternated into separate blocks of even and odd terms of Fibonacci length?

Active bilayer films of thermoplastic starch and polycaprolactone obtained by compression molding.

PubMed

Ortega-Toro, Rodrigo; Morey, Iris; Talens, Pau; Chiralt, Amparo

2015-08-20

Bilayer films consisting of one layer of PCL with either one of thermoplastic starch (S) or one of thermoplastic starch with 5% PCL (S95) were obtained by compression molding. Before compression, aqueous solutions of ascorbic acid or potassium sorbate were sprayed onto the S or S95 layers in order to plasticize them and favor layer adhesion. S95 films formed bilayers with PCL with very good adhesion and good mechanical performance, especially when potassium sorbate was added at the interface. All bilayers enhanced their barrier properties to water vapour (up to 96% compared to net starch films) and oxygen (up to 99% compared to PCL pure). Bilayers consisting of PCL and starch containing 5% PCL, with potassium sorbate at the interface, showed the best mechanical and barrier properties and interfacial adhesion while having active properties, associated with the antimicrobial action of potassium sorbate. Copyright © 2015 Elsevier Ltd. All rights reserved.

Bladder tissue engineering using biocompatible nanofibrous electrospun constructs: feasibility and safety investigation.

PubMed

Shakhssalim, Nasser; Dehghan, Mohammad Mehdi; Moghadasali, Reza; Soltani, Mohammad Hossein; Shabani, Iman; Soleimani, Masoud

2012-01-01

To investigate the feasibility and safety of using biocompatible, nanofibrous electrospun polycaprolactone (PCL) and combination of polylactic acid (PLLA) and PCL mats in a canine model. Plasma-treated electrospun unseeded mats were implanted in three dogs. The first dog was sacrificed after 3 months and the second and third ones after 4 months, and then, the graft was examined macroscopically with subsequent morphological and histochemical evaluation. Both films showed high levels of cell infiltration and tissue formation, but body response to PLLA/PCL mat in comparison to PCL mat was very low. All three implantation models showed the same light microscopic morphology, immunohistochemistry, and scanning electron microscopy results; nevertheless, only the PCL/PLLA model showed favorable clinical results. Based on these data, nanofibrous PLLA/PCL scaffolding could be a suitable material for the bladder tissue engineering; however, it deserves further investigations.

Theranostic self-assembly structure of gold nanoparticles for NIR photothermal therapy and X-Ray computed tomography imaging.

PubMed

Deng, Heng; Zhong, Yanqi; Du, Meihong; Liu, Qinjun; Fan, Zhanming; Dai, Fengying; Zhang, Xin

2014-01-01

The controllable self-assembly of amphiphilic mixed polymers grafted gold nanoparitcles (AuNPs) leads to strong interparticle plasmonic coupling, which can be tuned to the near-infrared (NIR) region for enhanced photothermal therapy (PTT). In this study, an improved thiolation method was adopted for ATRP and ROP polymer to obtain amphiphilic brushes of PMEO2MA-SH and PCL-SH. By anchoring PCL-SH and PMEO2MA-SH onto the 14 nm AuNPs, a smart hybrid building block for self-assembly was obtained. Increasing the PCL/PMEO2MA chain ratio from 0.8:1, 2:1 and 3:1 to 7:1, the structure of gold assemblies (GAs) was observed to transfer from vesicle to large compound micelle (LCM). Contributed to the special dense packed structure of gold nanoparticles in LCM, the absorption spectrometry of gold nanoparticles drastically red-shifted from 520 nm to 830 nm, which endowed the GAs remarkable NIR photothermal conversion ability. In addition, gold has high X-ray absorption coefficient which qualifies gold nanomaterial a potential CT contrast agent Herein, we obtain a novel gold assembly structure which can be utilized as potential photothermal therapeutic and CT contrast agents. In vitro and In vivo studies testified the excellent treatment efficacy of optimum GAs as a PTT and CT contrast agent. In vitro degradation test, MTT assay and histology study indicated that GAs was a safe, low toxic reagent with good biodegradability. Therefore, the optimum GAs with strong NIR absorption and high X-ray absorption coefficient could be used as a theranostic agent and the formation of novel gold large compound micelle might offers a new theory foundation for engineering design and synthesis of polymer grafted AuNPs for biomedical applications.

Primary Plasma Cell Leukemia Associated with t(6;14)(p21;q32) and IGH Rearrangement: A Case Study and Review of the Literature.

PubMed

Cho, Sun Young; Lim, Gayoung; Oh, Seung Hwan; Lee, Hee Joo; Suh, Jin-Tae; Lee, Juhie; Lee, Woo-In; Lee, Hong Ghi; Yoon, Hwi-Joong; Park, Tae Sung

2011-01-01

Because plasma cell leukemia (PCL) is a rare and distinct variant among plasma cell dyscrasias, recent clinical and cytogenetic studies have been performed in different ethnic groups to define the characteristics of these PCL patients. As far as we know, IGH rearrangements involving t(11;14) and (14;16) are significantly more frequent in PCL than in myeloma patients. However, PCL cases associated with t(6;14)(p21;q32) or IGH-CCND3 rearrangement are extremely rare in the literature; only one PCL case with t(6;14) has been documented. A 61-year-old female was admitted due to fatigue, weight loss, and exertional dyspnea. Plasmacytoid cells were counted up to 76% at a peripheral blood film, but bone marrow aspiration failed because of dry-tapping. Flow cytometric analysis showed positive for CD138 and cytoplasmic kappa light chain. Chromosome analysis revealed t(6;14)(p21;q32), which was confirmed by an IGH split-out probe in FISH analysis. Immunofixation electrophoresis also presented monoclonal bands identified as IgG and kappa light chain. Finally, she was diagnosed as primary PCL associated with t(6;14) and IGH rearrangement. Although considerable advances have been made in the understanding of the biology and molecular pathogenesis of PCL, further clinical, laboratory, and genetic studies of PCL associated with such a rare IGH rearrangement would be necessary in the future. To the best of our knowledge, this is the first report of PCL associated with t(6;14) as a sole chromosomal abnormality.

Effects of low-temperature hydrogen peroxide gas plasma sterilization on in vitro cytotoxicity of poly(ϵ-caprolactone) (PCL).

PubMed

Franklin, Samuel Patrick; Stoker, Aaron M; Cockrell, Mary K; Pfeiffer, Ferris M; Sonny Bal, B; Cook, James L

2012-01-01

Our objective was to determine whether low-temperature hydrogen peroxide (H2O2) gas plasma sterilization of porous three-dimensional poly(ϵ-caprolactone) (PCL) constructs significantly inhibits cellular metabolism of canine chondrocytes. Porous cylindrical constructs were fabricated using fused deposition modeling and divided into four sterilization groups. Two groups were sterilized with low-temperature H2O2 gas plasma (LTGP) and constructs from one of those groups were subsequently rinsed with Dulbecco's Modified Essential Media (LTGPDM). Constructs in the other two groups were disinfected with either 70% isopropyl alcohol or exposure to UV light. Canine chondrocytes were seeded in 6-well tissue-culture plates and allowed to adhere prior to addition of PCL. Cellular metabolism was assessed by adding resazurin to the tissue-culture wells and assessing conversion of this substrate by viable cells to the fluorescent die resorufin. This process was performed at three times prior to addition of PCL and at four times after addition of PCL to the tissue-culture wells. Metabolism was not significantly different among the different tissue-culture wells at any of the 3 times prior to addition of PCL. Metabolism was significantly different among the treatment groups at 3 of 4 times after addition of PCL to the tissue culture wells. Metabolism was significantly lower with constructs sterilized by LTGP than all other treatment groups at all 3 of these times. We conclude that LTGP sterilization of PCL constructs resulted in significant cytotoxicity to canine chondrocytes when compared to PCL constructs disinfected with either UV light exposure or 70% isopropyl alcohol.

Biocompatibility and biodegradation studies of PCL/β-TCP bone tissue scaffold fabricated by structural porogen method.

PubMed

Lu, Lin; Zhang, Qingwei; Wootton, David; Chiou, Richard; Li, Dichen; Lu, Bingheng; Lelkes, Peter; Zhou, Jack

2012-09-01

Three-dimensional printer (3DP) (Z-Corp) is a solid freeform fabrication system capable of generating sub-millimeter physical features required for tissue engineering scaffolds. By using plaster composite materials, 3DP can fabricate a universal porogen which can be injected with a wide range of high melting temperature biomaterials. Here we report results toward the manufacture of either pure polycaprolactone (PCL) or homogeneous composites of 90/10 or 80/20 (w/w) PCL/beta-tricalcium phosphate (β-TCP) by injection molding into plaster composite porogens fabricated by 3DP. The resolution of printed plaster porogens and produced scaffolds was studied by scanning electron microscopy. Cytotoxicity test on scaffold extracts and biocompatibility test on the scaffolds as a matrix supporting murine osteoblast (7F2) and endothelial hybridoma (EAhy 926) cells growth for up to 4 days showed that the porogens removal process had only negligible effects on cell proliferation. The biodegradation tests of pure PCL and PCL/β-TCP composites were performed in DMEM with 10 % (v/v) FBS for up to 6 weeks. The PCL/β-TCP composites show faster degradation rate than that of pure PCL due to the addition of β-TCP, and the strength of 80/20 PCL/β-TCP composite is still suitable for human cancellous bone healing support after 6 weeks degradation. Combining precisely controlled porogen fabrication structure, good biocompatibility, and suitable mechanical properties after biodegradation, PCL/β-TCP scaffolds fabricated by 3DP porogen method provide essential capability for bone tissue engineering.

Effect of partial and complete posterior cruciate ligament transection on medial meniscus: A biomechanical evaluation in a cadaveric model.

PubMed

Gao, Shu-Guang; Zhang, Can; Zhao, Rui-Bo; Liao, Zhan; Li, Yu-Sheng; Yu, Fang; Zeng, Chao; Luo, Wei; Li, Kang-Hua; Lei, Guang-Hua

2013-09-01

The relationship between medial meniscus tear and posterior cruciate ligament (PCL) injury has not been exactly explained. We studied to investigate the biomechanical effect of partial and complete PCL transection on different parts of medial meniscus at different flexion angles under static loading conditions. TWELVE FRESH HUMAN CADAVERIC KNEE SPECIMENS WERE DIVIDED INTO FOUR GROUPS: PCL intact (PCL-I), anterolateral bundle transection (ALB-T), posteromedial bundle transection (PMB-T) and PCL complete transection (PCL-T) group. Strain on the anterior horn, body part and posterior horn of medial meniscus were measured under different axial compressive tibial loads (200-800 N) at 0°, 30°, 60° and 90° knee flexion in each groups respectively. Compared with the PCL-I group, the PCL-T group had a higher strain on whole medial meniscus at 30°, 60° and 90° flexion in all loading conditions and at 0° flexion with 400, 600 and 800 N loads. In ALB-T group, strain on whole meniscus increased at 30°, 60° and 90° flexion under all loading conditions and at 0° flexion with 800 N only. PMB-T exihibited higher strain at 0° flexion with 400 N, 600 N and 800 N, while at 30° and 60° flexion with 800 N and at 90° flexion under all loading conditions. Partial PCL transection triggers strain concentration on medial meniscus and the effect is more pronounced with higher loading conditions at higher flexion angles.

Procedural learning: A developmental study of motor sequence learning and probabilistic classification learning in school-aged children.

PubMed

Mayor-Dubois, Claire; Zesiger, Pascal; Van der Linden, Martial; Roulet-Perez, Eliane

2016-01-01

In this study, we investigated motor and cognitive procedural learning in typically developing children aged 8-12 years with a serial reaction time (SRT) task and a probabilistic classification learning (PCL) task. The aims were to replicate and extend the results of previous SRT studies, to investigate PCL in school-aged children, to explore the contribution of declarative knowledge to SRT and PCL performance, to explore the strategies used by children in the PCL task via a mathematical model, and to see whether performances obtained in motor and cognitive tasks correlated. The results showed similar learning effects in the three age groups in the SRT and in the first half of the PCL tasks. Participants did not develop explicit knowledge in the SRT task whereas declarative knowledge of the cue-outcome associations correlated with the performances in the second half of the PCL task, suggesting a participation of explicit knowledge after some time of exposure in PCL. An increasing proportion of the optimal strategy use with increasing age was observed in the PCL task. Finally, no correlation appeared between cognitive and motor performance. In conclusion, we extended the hypothesis of age invariance from motor to cognitive procedural learning, which had not been done previously. The ability to adopt more efficient learning strategies with age may rely on the maturation of the fronto-striatal loops. The lack of correlation between performance in the SRT task and the first part of the PCL task suggests dissociable developmental trajectories within the procedural memory system.

Cryomilling for the fabrication of doxorubicin-containing silica-nanoparticle/polycaprolactone nanocomposite films

NASA Astrophysics Data System (ADS)

Gao, Yu; Lim, Jing; Han, Yiyuan; Wang, Lifeng; Chong, Mark Seow Khoon; Teoh, Swee-Hin; Xu, Chenjie

2016-01-01

Bionanocomposites need to have a homogeneous distribution of nanomaterials in the polymeric matrix to achieve consistent mechanical and biological functions. However, a significant challenge lies in achieving the homogeneous distribution of nanomaterials, particularly through a solvent-free approach. This report introduces a technology to address this need. Specifically, cryomilling, a solvent-free, low-temperature processing method, was applied to generate a bionanocomposite film with well-dispersed nanoparticles. As a proof-of-concept, polycaprolactone (PCL) and doxorubicin-containing silica nanoparticles (Si-Dox) were processed through cryomilling and subsequently heat pressed to form the PCL/Si-Dox (cPCL/Si-Dox) film. Homogeneous distribution of Si-Dox was observed under both confocal imaging and atomic force microscopy imaging. The mechanical properties of cPCL/Si-Dox were comparable to those of the pure PCL film. Subsequent in vitro release profiles suggested that sustained release of Dox from the cPCL/Si-Dox film was achievable over 50 days. When human cervical cancer cells were seeded directly on these films, uptake of Dox was observed as early as day 1 and significant inhibition of cell growth was recorded on day 5.Bionanocomposites need to have a homogeneous distribution of nanomaterials in the polymeric matrix to achieve consistent mechanical and biological functions. However, a significant challenge lies in achieving the homogeneous distribution of nanomaterials, particularly through a solvent-free approach. This report introduces a technology to address this need. Specifically, cryomilling, a solvent-free, low-temperature processing method, was applied to generate a bionanocomposite film with well-dispersed nanoparticles. As a proof-of-concept, polycaprolactone (PCL) and doxorubicin-containing silica nanoparticles (Si-Dox) were processed through cryomilling and subsequently heat pressed to form the PCL/Si-Dox (cPCL/Si-Dox) film. Homogeneous distribution of Si-Dox was observed under both confocal imaging and atomic force microscopy imaging. The mechanical properties of cPCL/Si-Dox were comparable to those of the pure PCL film. Subsequent in vitro release profiles suggested that sustained release of Dox from the cPCL/Si-Dox film was achievable over 50 days. When human cervical cancer cells were seeded directly on these films, uptake of Dox was observed as early as day 1 and significant inhibition of cell growth was recorded on day 5. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr07287e

Intratumoral administration of carboplatin bearing poly (ε-caprolactone) nanoparticles amalgamated with in situ gel tendered augmented drug delivery, cytotoxicity, and apoptosis in melanoma tumor.

PubMed

Bragta, Pallvi; Sidhu, Rupinder Kaur; Jyoti, Kiran; Baldi, Ashish; Jain, Upendra Kumar; Chandra, Ramesh; Madan, Jitender

2018-06-01

In a phase II clinical trial, carboplatin (CBDCA) displayed the response rate of 19% equivalent to dacarbazine in the treatment of malignant melanoma. However, besides desirable therapeutic profile, intravenous (i.v) administration of CBDCA delivers a subtherapeutic concentration at the target site. This entails administration of CBDCA through an alternate route by using nanovectors to achieve therapeutic efficacy in the treatment of melanoma. Carboplatin loaded poly(ε-caprolactone) nanoparticles (CBDCA-PCL-NPs) were formulated and amalgamated with chitosan-β-glycerophosphate gel (CBDCA-PCL-NPs-Gel) for intratumoral (i.t) administration. The mean particle size and zeta-potential of CBDCA-PCL-NPs were determined to be 54.5 ± 6.3-nm and -8.1 ± 0.9-mV, in addition to spherical shape of the nanoformulation. FT-IR spectroscopy denied any issue of chemical incompatibility between drug and polymer. XRD pattern indicated the amorphous lattice of CBDCA-PCL-NPs. The drug loading capacity of CBDCA-PCL-NPs-Gel was estimated to be 152 mg/1 ml. CBDCA-PCL-NPs-Gel demonstrated prolonged drug release up to 48 h. Furthermore, CBDCA-PCL-NPs-Gel displayed the IC 50 of 80.3-μM significantly (P < 0.05) lower than 162.8-μM of CBDCA-PCL-NPs and 248.5-μM of CBDCA solution in B16F1, melanoma cancer cells. CBDCA-PCL-NPs-Gel verified 80.2% of apoptosis significantly (P < 0.01) higher than 57.6% of CBDCA-PCL-NPs and 43.4% of CBDCA solution. Continuation to this, CBDCA-PCL-NPs-Gel significantly (P < 0.01) suppressed the tumor volume to 95.5 ± 8.4-mm 3 as compared to 178.9 ± 10.2-mm 3 of CBDCA solution injected i.t. and 210.6 ± 17.1-mm 3 displayed by CBDCA solution injected i.v. vis-à-vis 815.4 ± 17.1-mm 3 tumor volume of B16F1 tumor bearing C57BL6J mice. The promising preclinical results of CBDCA-PCL-NPs-Gel warrant further investigations under a set of stringent parameters for the treatment of melanoma. Copyright © 2018 Elsevier B.V. All rights reserved.

Posterior Cruciate Ligament Injuries Associated With Military Survival Swim Training.

PubMed

Crowell, Michael S; Mason, John S; Posner, Matthew A; Haley, Chad A

2017-07-01

Posterior cruciate ligament (PCL) injuries are relatively common injuries associated with athletic activities and high-energy trauma. Posterolateral corner (PLC) injuries frequently accompany injury to the PCL. Diagnosis can be challenging and requires a comprehensive history and physical examination. Patients frequently report vague, nonspecific symptoms and the mechanism of injury is often useful in localizing injured structures. Two of the more common mechanisms for PCL injury include a direct blow to the proximal anterior tibia with the knee flexed, as well as a significant knee hyperextension injury. With a PCL tear, patients rarely describe an audible "pop" that is commonly reported in ACL injuries. On physical exam, a frequent finding in PCL tears is a loss of 10 to 20° of knee flexion. Although the most common clinical tests for PCL tears include the posterior drawer test, the posterior sag sign, and the quadriceps active test, there is a lack of high-quality diagnostic accuracy studies. Two cases of U.S. Military Academy Cadets who sustained PCL injuries while removing combat boots during military survival swim training are presented. The results of the clinical examination are accompanied by magnetic resonance imaging results and intraoperative arthroscopic images to highlight key findings. Both patients were evaluated and diagnosed with PCL injures within 10 days of their injuries. Each reported feeling/hearing a "pop," which is atypical in PCL tears. Both patients demonstrated a lack of active and passive knee flexion, which is a commonly reported impairment. One patient was managed nonsurgically with physical therapy and eventually returned to full duty without limitations 9 months after his injury. The other patient, who sustained a combined PCL-PLC injury, underwent a PCL reconstruction and PLC repair and reconstruction 8 weeks after his injury. He returned all training, with the exception of contact/collision sports, 9 months after surgery. Both patient's rehabilitation programs consisted of a progression of exercises to improve range of motion, muscle strength/endurance, motor control, and muscular power. Military and sports medicine professionals should be aware of the potential for PCL injury with this unusual, and previously unreported, mechanism of injury during survival swim training. Prompt diagnosis and appropriate treatment is essential to prevent long-term disability. Reprint & Copyright © 2017 Association of Military Surgeons of the U.S.

3D printed porous polycaprolactone/oyster shell powder (PCL/OSP) scaffolds for bone tissue engineering

NASA Astrophysics Data System (ADS)

Luo, Wenfeng; Zhang, Shuangying; Lan, Yuewei; Huang, Chen; Wang, Chao; Lai, Xuexu; Chen, Hanwei; Ao, Ningjian

2018-04-01

In this work, oyster shell powder (OSP) was used as the bio-filler and combined with polycaprolactone (PCL) through melt blending methodology. The PCL and PCL/OSP scaffolds were prepared using additive manufacturing process. All the 3D printed scaffolds hold a highly porosity and interconnected pore structures. OSP particles are dispersed in the polymer matrix, which helped to improve the degree of crystallinity and mineralization ability of the scaffolds. There was no significant cytotoxicity of the prepared scaffolds towards MG-63 cells, and all the scaffolds showed a well ALP activity. Therefore, PCL/OSP scaffolds had a high potential to be employed in the bone tissue engineering.

A compound scaffold with uniform longitudinally oriented guidance cues and a porous sheath promotes peripheral nerve regeneration in vivo.

PubMed

Huang, Liangliang; Zhu, Lei; Shi, Xiaowei; Xia, Bing; Liu, Zhongyang; Zhu, Shu; Yang, Yafeng; Ma, Teng; Cheng, Pengzhen; Luo, Kai; Huang, Jinghui; Luo, Zhuojing

2018-03-01

Scaffolds with inner fillers that convey directional guidance cues represent promising candidates for nerve repair. However, incorrect positioning or non-uniform distribution of intraluminal fillers might result in regeneration failure. In addition, proper porosity (to enhance nutrient and oxygen exchange but prevent fibroblast infiltration) and mechanical properties (to ensure fixation and to protect regenerating axons from compression) of the outer sheath are also highly important for constructing advanced nerve scaffolds. In this study, we constructed a compound scaffold using a stage-wise strategy, including directionally freezing orientated collagen-chitosan (O-CCH) filler, electrospinning poly(ε-caprolactone) (PCL) sheaths and assembling O-CCH/PCL scaffolds. Based on scanning electron microscopy (SEM) and mechanical tests, a blend of collagen/chitosan (1:1) was selected for filler fabrication, and a wall thickness of 400 μm was selected for PCL sheath production. SEM and three-dimensional (3D) reconstruction further revealed that the O-CCH filler exhibited a uniform, longitudinally oriented microstructure (over 85% of pores were 20-50 μm in diameter). The electrospun PCL porous sheath with pore sizes of 6.5 ± 3.3 μm prevented fibroblast invasion. The PCL sheath exhibited comparable mechanical properties to commercially available nerve conduits, and the O-CCH filler showed a physiologically relevant substrate stiffness of 2.0 ± 0.4 kPa. The differential degradation time of the filler and sheath allows the O-CCH/PCL scaffold to protect regenerating axons from compression stress while providing enough space for regenerating nerves. In vitro and in vivo studies indicated that the O-CCH/PCL scaffolds could promote axonal regeneration and Schwann cell migration. More importantly, functional results indicated that the CCH/PCL compound scaffold induced comparable functional recovery to that of the autograft group at the end of the study. Our findings demonstrated that the O-CCH/PCL scaffold with uniform longitudinal guidance filler and a porous sheath exhibits favorable properties for clinical use and promotes nerve regeneration and functional recovery. The O-CCH/PCL scaffold provides a promising new path for developing an optimal therapeutic alternative for peripheral nerve reconstruction. Scaffolds with inner fillers displaying directional guidance cues represent a promising candidate for nerve repair. However, further clinical translation should pay attention to the problem of non-uniform distribution of inner fillers, the porosity and mechanical properties of the outer sheath and the morphological design facilitating operation. In this study, a stage-wise fabrication strategy was used, which made it possible to develop an O-CCH/PCL compound scaffold with a uniform longitudinally oriented inner filler and a porous outer sheath. The uniform distribution of the pores in the O-CCH/PCL scaffold provides a solution to resolve the problem of non-uniform distribution of inner fillers, which impede the clinical translation of scaffolds with longitudinal microstructured fillers, especially for aligned-fiber-based scaffolds. In vitro and in vivo studies indicated that the O-CCH/PCL scaffolds could provide topographical cues for axonal regeneration and SC migration, which were not found for random scaffolds (with random microstructure resemble sponge-based scaffolds). The electrospun porous PCL sheath of the O-CCH/PCL scaffold not only prevented fibroblast infiltration, but also satisfied the mechanical requirements for clinical use, paving the way for clinical translation. The differential degradation time of the O-CCH filler and the PCL sheath makes O-CCH/PCL scaffold able to provide long protection for regenerating axons from compression stress, but enough space for regenerating nerve. These findings highlight the possibility of developing an optimal therapeutic alternative for nerve defects using the O-CCH/PCL scaffold. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Robotic dispensing of composite scaffolds and in vitro responses of bone marrow stromal cells.

PubMed

Hong, Seok-Jung; Jeong, Ishik; Noh, Kyung-Tae; Yu, Hye-Sun; Lee, Gil-Su; Kim, Hae-Won

2009-09-01

The development of bioactive scaffolds with a designed pore configuration is of particular importance in bone tissue engineering. In this study, bone scaffolds with a controlled pore structure and a bioactive composition were produced using a robotic dispensing technique. A poly(epsilon-caprolactone) (PCL) and hydroxyapatite (HA) composite solution (PCL/HA = 1) was constructed into a 3-dimensional (3D) porous scaffold by fiber deposition and layer-by-layer assembly using a computer-aided robocasting machine. The in vitro tissue cell compatibility was examined using rat bone marrow stromal cells (rBMSCs). The adhesion and growth of cells onto the robotic dispensed scaffolds were observed to be limited by applying the conventional cell seeding technique. However, the initially adhered cells were viable on the scaffold surface. The alkaline phosphatase activity of the cells was significantly higher on the HA-PCL than on the PCL and control culture dish, suggesting that the robotic dispensed HA-PCL scaffold should stimulate the osteogenic differentiation of rBMSCs. Moreover, the expression of a series of bone-associated genes, including alkaline phosphatase and collagen type I, was highly up-regulated on the HA-PCL scaffold as compared to that on the pure PCL scaffold. Overall, the robotic dispensed HA-PCL is considered to find potential use as a bioactive 3D scaffold for bone tissue engineering.

The posterior cruciate ligament: a study on its bony and soft tissue anatomy using novel 3D CT technology.

PubMed

Van Hoof, Tom; Cromheecke, Michiel; Tampere, Thomas; D'herde, Katharina; Victor, Jan; Verdonk, Peter C M

2013-05-01

The bony insertion sites of the PCL have been studied and described extensively using 2D technology such as macroscopic images, plain radiograph, computerized tomography (CT) and MRI. The purpose of this study is to visualize both the tibial and the femoral bony insertion sites but also the soft tissue anatomy of the native PCL using novel 3D CT imaging. In addition, new concepts of best-fit cylinder and central axis are introduced and evaluated. Nine unpaired knees of embalmed cadavers were used in this study. Following the dissection process, the PCL was injected with a contrast medium for computed tomography (CT) imaging. The obtained CT images were segmented and rendered in 3D allowing morphological and morphometric analysis of PCL. Femoral and tibial footprint surface area, best-fit PCL-cylinder intersection area, best-fit PCL-cylinder/footprint coverage ratio, best-fit PCL-cylinder central axis projections at the tibial and femoral footprint were used to describe the anatomy of the PCL. Mean footprint surface area of the tibial and femoral footprint were 189.1 and 293.3 mm², respectively. The mean diameter of the best-fit cylinder was 10.5 mm. The mean coverage of the best-fit cylinder on the tibial and femoral footprint was 76.5 and 46.5, respectively. The best-fit cylinder central axis was located in the anterolateral AL bundle footprint on the femur and more centrally in the PCL footprint on the tibia. This study is the first to describe the detailed anatomy of the human PCL with respect to its course and footprints using a 3D approach. It confirms the large difference between the tibial and the femoral footprint area with the former being significantly smaller. In addition, a large inter-patient variability is observed. The best-fit cylinder and central axis concept offer additional insights into the optimal tunnel placement at the tibia and femoral footprint in order to cover the largest portion of the native PCL soft tissue.

Structure and properties of slow-resorbing nanofibers obtained by (co-axial) electrospinning as tissue scaffolds in regenerative medicine

PubMed Central

Gola, Joanna; Ghavami, Saeid; Skonieczna, Magdalena; Markowski, Jarosław; Likus, Wirginia; Lewandowska, Magdalena; Maziarz, Wojciech

2017-01-01

With the rapid advancement of regenerative medicine technologies, there is an urgent need for the development of new, cell-friendly techniques for obtaining nanofibers—the raw material for an artificial extracellular matrix production. We investigated the structure and properties of PCL10 nanofibers, PCL5/PCL10 core-shell type nanofibers, as well as PCL5/PCLAg nanofibres prepared by electrospinning. For the production of the fiber variants, a 5–10% solution of polycaprolactone (PCL) (Mw = 70,000–90,000), dissolved in a mixture of formic acid and acetic acid at a ratio of 70:30 m/m was used. In order to obtain fibers containing PCLAg 1% of silver nanoparticles was added. The electrospin was conducted using the above-described solutions at the electrostatic field. The subsequent bio-analysis shows that synthesis of core-shell nanofibers PCL5/PCL10, and the silver-doped variant nanofiber core shell PCL5/PCLAg, by using organic acids as solvents, is a robust technique. Furthermore, the incorporation of silver nanoparticles into PCL5/PCLAg makes such nanofibers toxic to model microbes without compromising its biocompatibility. Nanofibers obtained such way may then be used in regenerative medicine, for the preparation of extracellular scaffolds: (i) for controlled bone regeneration due to the long decay time of the PCL, (ii) as bioscaffolds for generation of other types of artificial tissues, (iii) and as carriers of nanocapsules for local drug delivery. Furthermore, the used solvents are significantly less toxic than the solvents for polycaprolactone currently commonly used in electrospin, like for example chloroform (CHCl3), methanol (CH3OH), dimethylformamide (C3H7NO) or tetrahydrofuran (C4H8O), hence the presented here electrospin technique may allow for the production of multilayer nanofibres more suitable for the use in medical field. PMID:29302386

Virally inactivated human platelet concentrate lysate induces regulatory T cells and immunosuppressive effect in a murine asthma model.

PubMed

Lee, Yueh-Lun; Lee, Lin-Wen; Su, Chen-Yao; Hsiao, George; Yang, Yi-Yuan; Leu, Sy-Jye; Shieh, Ying-Hua; Burnouf, Thierry

2013-09-01

Platelet concentrate lysates (PCLs) are increasingly used in regenerative medicine. We have developed a solvent/detergent (S/D)-treated PCL. The functional properties of this preparation should be unveiled. We hypothesized that, due to transforming growth factor-β1 (TGF-β1) content, PCLs may exert immunosuppressive and anti-inflammatory functions. PCL was prepared by S/D treatment, oil extraction, and hydrophobic interaction chromatography. The content of TGF-β in PCL was determined by enzyme-linked immunosorbent assay. Cultured CD4+ T cells were used to investigate the effects of PCL on expression of transcription factor forkhead box P3 (Foxp3), the inhibition of T-cell proliferation, and cytokine production. The regulatory function of PCL-converted CD4+ T cells was analyzed by suppressive assay. The BALB/c mice were given PCL-converted CD4+ T cells before ovalbumin (OVA) sensitization and challenge using an asthma model. Inflammatory parameters, such as the level of immunoglobulin E (IgE), airway hyperresponsiveness (AHR), bronchial lavage fluid eosinophils, and cytokines were assayed. Recombinant human (rHu) TGF-β1 was used as control. PCL significantly enhanced the development of CD4+Foxp3+-induced regulatory T cells (iTregs). Converted iTregs produced neither Th1 nor Th2 cytokines and inhibited normal T-cell proliferation. PCL- and rHuTGF-β-converted CD4+ T cells prevented OVA-induced asthma. PCL- and rHuTGF-β-modified T cells both significantly reduced expression levels of OVA-specific IgE and significantly inhibited the development of AHR, airway eosinophilia, and Th2 responses in mice. S/D-treated PCL promotes Foxp3+ iTregs and exerts immunosuppressive and anti-inflammatory properties. This finding may help to understand the clinical properties of platelet lysates. © 2013 American Association of Blood Banks.

The resistance of polyvinylpyrrolidone-iodine-poly(-caprolactone) blends to adherence of Escherichia coli.

PubMed

Jones, David S; Djokic, Jasmina; Gorman, Sean P

2005-05-01

In this study, the resistance of biodegradable biomaterials, composed of blends of poly(-caprolactone) (PCL) and the polymeric antimicrobial complex, polyvinylpyrrolidone-iodine (PVP-I) to the adherence of a clinical isolate of Escherichia coli is described. Blends of PCL composed of a range of high (50,000 g mol(-1)) to low (5000 g mol(-1)) molecular weight ratios of polymer and either devoid of or containing PVP-I (1% w/w) were prepared by solvent evaporation. Following incubation (4 h), there was no relationship between m. wt. ratio of PCL in films devoid of PVP-I and adherence of E. coli. Conversely, microbial adherence to PCL containing PVP-I decreased as the ratio of high:low m. wt. polymer was decreased and was approximately 1000 fold lower than that to comparator films devoid of PVP-I. Following periods of immersion of PVP-I containing PCL films under sink conditions in phosphate buffered saline, subsequent adherence of E. coli was substantially reduced for 2 days (40:60 m. wt. ratio) and 6 days (100:0 m. wt. ratio). Concurrent exposure of PCL and E. coli to sub-minimum inhibitory concentrations (sub-MIC) of PVP-I significantly reduced microbial adherence to the biomaterial; however, the molecular weight ratio of PCL did not affect this outcome. Pretreatment of PCL with similar sub-MIC of PVP-I prior to inclusion within the microbial adherence assay significantly decreased the subsequent adherence of E. coli. Greatest reduction in adherence was observed following treatment of PCL (40:60 m. wt. ratio) with 0.0156% w/w PVP-I. In conclusion, this study has illustrated the utility of PVP-I as a suitable therapeutic agent for incorporation within PCL as a novel biomaterial. Due to the combined antimicrobial and biodegradable properties, these biomaterials offer a promising strategy for the reduction in medical device related infection.

Fabrication of a Highly Aligned Neural Scaffold via a Table Top Stereolithography 3D Printing and Electrospinning^.

PubMed

Lee, Se-Jun; Nowicki, Margaret; Harris, Brent; Zhang, Lijie Grace

2017-06-01

Three-dimensional (3D) bioprinting is a rapidly emerging technique in the field of tissue engineering to fabricate extremely intricate and complex biomimetic scaffolds in the range of micrometers. Such customized 3D printed constructs can be used for the regeneration of complex tissues such as cartilage, vessels, and nerves. However, the 3D printing techniques often offer limited control over the resolution and compromised mechanical properties due to short selection of printable inks. To address these limitations, we combined stereolithography and electrospinning techniques to fabricate a novel 3D biomimetic neural scaffold with a tunable porous structure and embedded aligned fibers. By employing two different types of biofabrication methods, we successfully utilized both synthetic and natural materials with varying chemical composition as bioink to enhance biocompatibilities and mechanical properties of the scaffold. The resulting microfibers composed of polycaprolactone (PCL) polymer and PCL mixed with gelatin were embedded in 3D printed hydrogel scaffold. Our results showed that 3D printed scaffolds with electrospun fibers significantly improve neural stem cell adhesion when compared to those without the fibers. Furthermore, 3D scaffolds embedded with aligned fibers showed an enhancement in cell proliferation relative to bare control scaffolds. More importantly, confocal microscopy images illustrated that the scaffold with PCL/gelatin fibers greatly increased the average neurite length and directed neurite extension of primary cortical neurons along the fiber. The results of this study demonstrate the potential to create unique 3D neural tissue constructs by combining 3D bioprinting and electrospinning techniques.

Earliest Example of a Giant Monitor Lizard (Varanus, Varanidae, Squamata)

PubMed Central

Conrad, Jack L.; Balcarcel, Ana M.; Mehling, Carl M.

2012-01-01

Background Varanidae is a clade of tiny (<20 mm pre-caudal length [PCL]) to giant (>600 mm PCL) lizards first appearing in the Cretaceous. True monitor lizards (Varanus) are known from diagnostic remains beginning in the early Miocene (Varanus rusingensis), although extremely fragmentary remains have been suggested as indicating earlier Varanus. The paleobiogeographic history of Varanus and timing for origin of its gigantism remain uncertain. Methodology/Principal Findings A new Varanus from the Mytilini Formation (Turolian, Miocene) of Samos, Greece is described. The holotype consists of a partial skull roof, right side of a braincase, partial posterior mandible, fragment of clavicle, and parts of six vertebrae. A cladistic analysis including 83 taxa coded for 5733 molecular and 489 morphological characters (71 previously unincluded) demonstrates that the new fossil is a nested member of an otherwise exclusively East Asian Varanus clade. The new species is the earliest-known giant (>600 mm PCL) terrestrial lizard. Importantly, this species co-existed with a diverse continental mammalian fauna. Conclusions/Significance The new monitor is larger (longer) than 99% of known fossil and living lizards. Varanus includes, by far, the largest limbed squamates today. The only extant non-snake squamates that approach monitors in maximum size are the glass-snake Pseudopus and the worm-lizard Amphisbaena. Mosasauroids were larger, but exclusively marine, and occurred only during the Late Cretaceous. Large, extant, non-Varanus, lizards are limbless and/or largely isolated from mammalian competitors. By contrast, our new Varanus achieved gigantism in a continental environment populated by diverse eutherian mammal competitors. PMID:22900001

Humid Heat Autoclaving of Hybrid Nanoparticles Achieved by Decreased Nanoparticle Concentration and Improved Nanoparticle Stability Using Medium Chain Triglycerides as a Modifier.

PubMed

Gou, Jingxin; Chao, Yanhui; Liang, Yuheng; Zhang, Ning; He, Haibing; Yin, Tian; Zhang, Yu; Xu, Hui; Tang, Xing

2016-09-01

Humid heat autoclaving is a facile technique widely used in the sterilization of injections, but the high temperature employed would destroy nanoparticles composed of biodegradable polymers. The aim of this study was to investigate whether incorporation of medium chain triglycerides (MCT) could stabilize nanoparticles composed of poly (ethylene glycol)-b-polycaprolactone (PEG-b-PCL) during autoclaving (121°C, 10 min). Polymeric nanoparticles with different MCT contents were prepared by dialysis. Block copolymer degradation was studied by GPC. The critical aggregation concentrations of nanoparticles at different temperatures were determined using pyrene fluorescence. The size, morphology and weight averaged molecular weight of pristine/autoclaved nanoparticles were studied using DLS, TEM and SLS, respectively. Drug loading content and release profile were determined using RP-HPLC. The protecting effect of MCT on nanoparticles was dependent on the amount of MCT incorporated. Nanoparticles with high MCT contents, which assumed an emulsion-like morphology, showed reduced block copolymer degradation and particle disassociation after incubation at 100°C for 24 h. Nanoparticles with high MCT content showed the lowest critical aggregation concentration (CAC) under either room temperature or 60°C and the lowest particle concentration among all samples. And the particle size, drug loading content, physical stability and release profile of nanoparticles with high MCT contents remained nearly unchanged after autoclaving. Incorporation of high amount of MCT changed the morphology of PEG-b-PCL based nanoparticles to an emulsion-like structure and the nanoparticles prepared could withstand autoclaving due to improved particle stability and decreased particle concentration caused by MCT incorporation.

pH-responsive unimolecular micelles self-assembled from amphiphilic hyperbranched block copolymer for efficient intracellular release of poorly water-soluble anticancer drugs.

PubMed

Tabatabaei Rezaei, Seyed Jamal; Abandansari, Hamid Sadeghi; Nabid, Mohammad Reza; Niknejad, Hassan

2014-07-01

Novel unimolecular micelles from amphiphilic hyperbranched block copolymer H40-poly(ε-caprolactone)-b-poly(acrylic acid)-b'-methoxy poly(ethylene glycol)/poly(ethylene glycol)-folate (i.e., H40-PCL-b-PAA-b'-MPEG/PEG-FA (HCAE-FA)) as new multifunctional nanocarriers to pH-induced accelerated release and tumor-targeted delivery of poorly water-soluble anticancer drugs were developed. The hydrophobic core of the unimolecular micelle was hyperbranched polyester (H40-poly(ε-caprolactone) (H40-PCL)). The inner hydrophilic layer was composed of PAA segments, while the outer hydrophilic shell was composed of PEG segments. This copolymer formed unimolecular micelles in the aqueous solution with a mean particle size of 33 nm, as determined by dynamic light scattering (DLS) and transmission electron microscopy (TEM). To study the feasibility of micelles as a potential nanocarrier for targeted drug delivery, we encapsulated a hydrophobic anticancer drug, paclitaxel (PTX), in the hydrophobic core, and the loading content was determined by UV-vis analysis to be 10.35 wt.%. In vitro release studies demonstrated that the drug-loaded delivery system is relatively stable at physiologic conditions but susceptible to acidic environments which would trigger the release of encapsulated drugs. Flow cytometry and fluorescent microscope studies revealed that the cellular binding of the FA-conjugated micelles against HeLa cells was higher than that of the neat micelles (without FA). The in vitro cytotoxicity studies showed that the PTX transported by these micelles was higher than that by the commercial PTX formulation Tarvexol®. All of these results show that these unique unimolecular micelles may offer a very promising approach for targeted cancer therapy. Copyright © 2014 Elsevier Inc. All rights reserved.

Ultrasonochemically conjugated metalloid/triblock copolymer nanocomposite and subsequent thin solid laminate growth for surface and interface studies.

PubMed

Veerapandian, Murugan; Yun, KyuSik

2010-09-07

Polymer and metalloid nanoparticles can be conjugated in a symphonized manner using ultrasonochemical force to obtain hybrid nanocomposites. The process is demonstrated using polymer poly(ethylene glycol) (PEG), metalloid SiO(2)@Ag, and triblock copolymer ABA. The acoustic microstreaming and cavitation force from the ultrasonics are crucial parameters that determine the harmonized PEG stabilization and ABA blending of the metalloid nanocomposites that are obtained. Surface plasmon resonance in the resulting hybrid systems are examined by UV-vis absorbance spectroscopy. The resulting PEG-stabilized SiO(2)-Ag conjugated with a triblock copolymer poly(p-dioxanone-co-caprolactone)-block-poly(ethylene oxide)-block-poly(p-dioxanone-co-caprolactone) (PPDO-co-PCL-b-PEG-b-PPDO-co-PCL/ABA) (PEG-SiO(2)@Ag/ABA) shows a red shift of 20 nm (410 nm) from its initial resonance at 390 nm (PEG-SiO(2)@Ag). Nanocomposite particles were then spin-coated on a glass substrate to obtain the growth of thin solid laminates (thickness 27 microm). Structural functionality was studied by FT-IR, (1)H NMR, and FT-Raman spectroscopy. Morphological properties were ensured from FE-SEM, HRTEM, AFM, and FIB-SEM. Identity and crystallinity of the prepared nanocomposite were confirmed by XRD analysis. A very low weight percentile loss of the fabricated nanocomposites ensures its high thermal stability. Fabricated nanocomposite laminate might have a role in coating, reinforcement, and resistance and as substrate additives for a variety of surface and interface studies. Further, the ultrasonochemical approach utilized here could also be a smart system to fabricate other heteronanostructures in a single platform.

Mechanical and thermal properties of conventional and microcellular injection molded poly (lactic acid)/poly (ε-caprolactone) blends.

PubMed

Zhao, Haibin; Zhao, Guoqun

2016-01-01

In view of their complementary properties, blending polylactide (PLA) with poly (ε-caprolactone) (PCL) becomes a good choice to improve PLA's properties without compromising its biodegradability. A series of blends of biodegradable PLA and PCL with different mass fraction were prepared by melt mixing. Standard tensile bars were produced by both conventional and microcellular injection molding to study their mechanical and thermal properties. With the increase in PCL content, the blend showed decreased tensile strength and modulus; however, elongation was dramatically increased. With the addition of PCL, the failure mode changed from brittle fracture of the neat PLA to ductile fracture of the blend as demonstrated by tensile test. Various theoretical models based on dispersion and interface adhesion were used to predict the Young's modulus and the results shows the experimental data are consistent with the predictions of the foam model and Kerner-Uemura-Takayangi model. The thermal behavior of the blends was investigated by DSC and TGA. The melting temperature and the degree of crystallinity of PCL in the PLA/PCL did not significantly change with the PCL content increasing in the whole range of blends composition. Copyright © 2015 Elsevier Ltd. All rights reserved.

The German version of the Posttraumatic Stress Disorder Checklist for DSM-5 (PCL-5): psychometric properties and diagnostic utility.

PubMed

Krüger-Gottschalk, Antje; Knaevelsrud, Christine; Rau, Heinrich; Dyer, Anne; Schäfer, Ingo; Schellong, Julia; Ehring, Thomas

2017-11-28

The Posttraumatic Stress Disorder (PTSD) Checklist (PCL, now PCL-5) has recently been revised to reflect the new diagnostic criteria of the disorder. A clinical sample of trauma-exposed individuals (N = 352) was assessed with the Clinician Administered PTSD Scale for DSM-5 (CAPS-5) and the PCL-5. Internal consistencies and test-retest reliability were computed. To investigate diagnostic accuracy, we calculated receiver operating curves. Confirmatory factor analyses (CFA) were performed to analyze the structural validity. Results showed high internal consistency (α = .95), high test-retest reliability (r = .91) and a high correlation with the total severity score of the CAPS-5, r = .77. In addition, the recommended cutoff of 33 on the PCL-5 showed high diagnostic accuracy when compared to the diagnosis established by the CAPS-5. CFAs comparing the DSM-5 model with alternative models (the three-factor solution, the dysphoria, anhedonia, externalizing behavior and hybrid model) to account for the structural validity of the PCL-5 remained inconclusive. Overall, the findings show that the German PCL-5 is a reliable instrument with good diagnostic accuracy. However, more research evaluating the underlying factor structure is needed.

Production of Poly(ε-Caprolactone)/Hydroxyapatite Composite Scaffolds with a Tailored Macro/Micro-Porous Structure, High Mechanical Properties, and Excellent Bioactivity

PubMed Central

Kim, Jong-Woo; Shin, Kwan-Ha; Koh, Young-Hag; Hah, Min Jin; Moon, Jiyoung; Kim, Hyoun-Ee

2017-01-01

We produced poro-us poly(ε-caprolactone) (PCL)/hydroxyapatite (HA) composite scaffolds for bone regeneration, which can have a tailored macro/micro-porous structure with high mechanical properties and excellent in vitro bioactivity using non-solvent-induced phase separation (NIPS)-based 3D plotting. This innovative 3D plotting technique can create highly microporous PCL/HA composite filaments by inducing unique phase separation in PCL/HA solutions through the non-solvent-solvent exchange phenomenon. The PCL/HA composite scaffolds produced with various HA contents (0 wt %, 10 wt %, 15 wt %, and 20 wt %) showed that PCL/HA composite struts with highly microporous structures were well constructed in a controlled periodic pattern. Similar levels of overall porosity (~78 vol %) and pore size (~248 µm) were observed for all the PCL/HA composite scaffolds, which would be highly beneficial to bone tissue regeneration. Mechanical properties, such as ultimate tensile strength and compressive yield strength, increased with an increase in HA content. In addition, incorporating bioactive HA particles into the PCL polymer led to remarkable enhancements in in vitro apatite-forming ability. PMID:28937605

Impact of motility and chemotaxis features of the rhizobacterium Pseudomonas chlororaphis PCL1606 on its biocontrol of avocado white root rot.

PubMed

Polonio, Álvaro; Vida, Carmen; de Vicente, Antonio; Cazorla, Francisco M

2017-06-01

The biocontrol rhizobacterium Pseudomonas chlororaphis PCL1606 has the ability to protect avocado plants against white root rot produced by the phytopathogenic fungus Rosellinia necatrix. Moreover, PCL1606 displayed direct interactions with avocado roots and the pathogenic fungus. Thus, nonmotile (flgK mutant) and non-chemotactic (cheA mutant) derivatives of PCL1606 were constructed to emphasize the importance of motility and chemotaxis in the biological behaviour of PCL1606 during the biocontrol interaction. Plate chemotaxis assay showed that PCL1606 was attracted to the single compounds tested, such as glucose, glutamate, succinate, aspartate and malate, but no chemotaxis was observed to avocado or R. necatrix exudates. Using the more sensitive capillary assay, it was reported that smaller concentrations (1 mM) of single compounds elicited high chemotactic responses, and strong attraction was confirmed to avocado and R. necatrix exudates. Finally, biocontrol experiments revealed that the cheA and fglK derivative mutants reduced root protection against R. necatrix, suggesting an important role for these biological traits in biocontrol by P. chlororaphis PCL1606. [Int Microbiol 20(2):94-104 (2017)]. Copyright© by the Spanish Society for Microbiology and Institute for Catalan Studies.

Portuguese version of the PTSD Checklist-Military Version (PCL-M)-I: Confirmatory Factor Analysis and reliability.

PubMed

Carvalho, Teresa; Cunha, Marina; Pinto-Gouveia, José; Duarte, Joana

2015-03-30

The PTSD Checklist-Military Version (PCL-M) is a brief self-report instrument widely used to assess Post-traumatic Stress Disorder (PTSD) symptomatology in war Veterans, according to DSM-IV. This study sought out to explore the factor structure and reliability of the Portuguese version of the PCL-M. A sample of 660 Portuguese Colonial War Veterans completed the PCL-M. Several Confirmatory Factor Analyses were conducted to test different structures for PCL-M PTSD symptoms. Although the respecified first-order four-factor model based on King et al.'s model showed the best fit to the data, the respecified first and second-order models based on the DSM-IV symptom clusters also presented an acceptable fit. In addition, the PCL-M showed adequate reliability. The Portuguese version of the PCL-M is thus a valid and reliable measure to assess the severity of PTSD symptoms as described in DSM-IV. Its use with Portuguese Colonial War Veterans may ease screening of possible PTSD cases, promote more suitable treatment planning, and enable monitoring of therapeutic outcomes. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Anatomical dissection and CT imaging of the posterior cruciate and lateral collateral ligaments in skeletally immature cadaver knees.

PubMed

Shea, Kevin G; Polousky, John D; Jacobs, John C; Ganley, Theodore J

2014-05-07

Understanding the relationship of the posterior cruciate ligament (PCL) and the lateral collateral ligament (LCL) to the femoral and tibial physes is important to reducing the risk of physeal injury during surgical reconstruction. The purpose of this study was to identify the location of the attachments of the PCL and LCL in skeletally immature cadaveric knee specimens and to determine their position relative to the physes. Seven skeletally immature cadaveric knee specimens were examined through gross dissection. These specimens were divided into two groups: infants (an age at death of one month for one specimen and eleven months for two specimens) and children (an age at death of eight years for one specimen, ten years for one specimen, and eleven years for two specimens). Metallic markers were placed at the femoral origins of the PCL and LCL and at the tibial insertion of the PCL. Computed tomography (CT) scans were made for each specimen and analyzed with the use of OsiriX imaging software. The width of the PCL tibial insertion footprint and the height of the PCL femoral origin footprint, the distance from the midpoints of the PCL and LCL femoral origin to the distal femoral physis, and the distance from the PCL insertion footprint midpoint to the proximal tibial physis were measured. The mean distance from the midpoint of the femoral origin footprint of the PCL to the femoral physis was 11.1 mm (range, 10.6 to 11.7 mm) and 18.8 mm (range, 18.2 to 19.2 mm) distal to the physis for infants and children, respectively. The mean distance from the midpoint of the tibial insertion footprint of the PCL to the tibial physis was 3.1 mm (range, 0.0 to 5.7 mm) and 5.8 mm (range, 2.5 to 8.9 mm) proximal to the physis for infants and children, respectively. The mean width of the tibial insertion of the PCL was 5.5 mm (range, 1.1 to 8.3 mm) for infants and 10.2 mm (range, 8.4 to 11.9 mm) for children. The mean distance from the midpoint of the femoral origin of the LCL to the femoral physis was 6.3 mm (range, 3.9 to 7.7 mm) and 5.9 mm (range, 0.0 to 10.0 mm) distal to the physis for infants and children, respectively. The relationship of the PCL and LCL attachments to physeal structures has not been well described. We found the midpoints of the PCL and LCL femoral origins at or distal to, and the midpoint of the PCL tibial insertion at or proximal to, the respective physis in all specimens. This study with CT-scan correlation provides unique information on the location of ligament attachments in relation to the physes. A better understanding of the spatial relationship between the PCL and LCL attachments and their respective physes may help guide drill-hole placement during ligament reconstructions and reduce the risk for iatrogenic physeal injury in skeletally immature patients.

Block Copolymer Directed Biomimetic Mineral Formation for Polymer Nanocomposites

NASA Astrophysics Data System (ADS)

Gleeson, Sarah; Yu, Tony; Chen, Xi; Marcolongo, Michele; Li, Christopher

Bone is a hierarchically structured biocomposite comprised of mineralized collagen fibrils. The mechanical properties of bone can be precisely tuned by the structure and morphology of the mineral nanocrystals as well as the organic collagen fibrils. Synthetic materials that can mimic the nanostructure of natural bone show promise to replicate bone's structural function, yet little is known about the mechanism of mineral formation. We previously have shown that hierarchically ordered polymer fibers control the distribution and orientation of hydroxyapatite, enhancing mechanical properties and biocompatibility. We demonstrate a new method for mineralization by forming block copolymer single crystal films of polycaprolactone-block-poly(acrylic acid) (PCL- b-PAA) so that lamellar anionic PAA nanodomains recruit mineral ions and provide one-dimensional confinement to induce orientation. The effect of the anionic domain dimensions on mineral content, orientation, and structure within the polymer matrix is shown. The mechanical properties of the nanocomposite are evaluated to determine the role of mineral orientation and crystallinity in composite strength. These results can be used to tailor the physical mineralization environment to create a more biomimetic bone material.

Effect of film thickness on morphological evolution in dewetting and crystallization of polystyrene/poly(ε-caprolactone) blend films.

PubMed

Ma, Meng; He, Zhoukun; Yang, Jinghui; Chen, Feng; Wang, Ke; Zhang, Qin; Deng, Hua; Fu, Qiang

2011-11-01

In this Article, the morphological evolution in the blend thin film of polystyrene (PS)/poly(ε-caprolactone) (PCL) was investigated via mainly AFM. It was found that an enriched two-layer structure with PS at the upper layer and PCL at the bottom layer was formed during spinning coating. By changing the solution concentration, different kinds of crystal morphologies, such as finger-like, dendritic, and spherulitic-like, could be obtained at the bottom PCL layer. These different initial states led to the morphological evolution processes to be quite different from each other, so the phase separation, dewetting, and crystalline morphology of PS/PCL blend films as a function of time were studied. It was interesting to find that the morphological evolution of PS at the upper layer was largely dependent on the film thickness. For the ultrathin (15 nm) blend film, a liquid-solid/liquid-liquid dewetting-wetting process was observed, forming ribbons that rupture into discrete circular PS islands on voronoi finger-like PCL crystal. For the thick (30 nm) blend film, the liquid-liquid dewetting of the upper PS layer from the underlying adsorbed PCL layer was found, forming interconnected rim structures that rupture into discrete circular PS islands embedded in the single lamellar PCL dendritic crystal due to Rayleigh instability. For the thicker (60 nm) blend film, a two-step liquid-liquid dewetting process with regular holes decorated with dendritic PCL crystal at early annealing stage and small holes decorated with spherulite-like PCL crystal among the early dewetting holes at later annealing stage was observed. The mechanism of this unusual morphological evolution process was discussed on the basis of the entropy effect and annealing-induced phase separation.

Is the posterior cruciate ligament destabilized after the tibial cut in a cruciate retaining total knee replacement? An anatomical study.

PubMed

Liabaud, Barthelemy; Patrick, David A; Geller, Jeffrey A

2013-12-01

Cruciate retaining total knee replacement has been shown to effectively improve pain and quality of life. Successful outcomes depend on many factors, including the maintenance of a competent posterior cruciate ligament. This study sought to anatomically analyze the percentage of PCL injured during a full transverse, tibial cut, thus altering normal function. One hundred and thirty five consecutive knee MRIs taken from 2006 to 2011 were selected from a single surgeon's database for this study. Only subjects with non-arthritic knees were considered for this study; the lack of degenerative joint disease (DJD) was confirmed via a radiological report. The optimal view of the PCL's tibial attachment was observed using the sagittal view of the knee, with a T1 signal. One hundred and twenty two usable images were viewed electronically, and measurements were made using the standardized transverse cut implant guidelines. The percentage of PCL remaining following the cut was categorized into five different groups: 0% (no PCL undermined), 1-49%, 50-74%, 75-99% and 100% (PCL undermined entirely). Overall only 9.0% (n=11) would have not endured any damage to the PCL with a transverse tibial saw cut, while 79.6% (n=98) would have had 50% or more of the PCL undermined. Of the 98 patients with more than 50% resected, 52.1% (n=51 patients) presented complete destabilization of the PCL. The percentage of PCL destabilized was not significant across age groups (p=0.280), gender (p=0.586), or operative side (p=0.460). Independent of age, gender, and operative side, a majority of PCLs are more than 50% destabilized following the standard transverse tibial cut. II. Copyright © 2013 Elsevier B.V. All rights reserved.

Three-dimensional polycaprolactone-hydroxyapatite scaffolds combined with bone marrow cells for cartilage tissue engineering.

PubMed

Wei, Bo; Yao, Qingqiang; Guo, Yang; Mao, Fengyong; Liu, Shuai; Xu, Yan; Wang, Liming

2015-08-01

The goal of this study was to investigate the chondrogenic potential of three-dimensional polycaprolactone-hydroxyapatite (PCL-HA) scaffolds loaded with bone marrow cells in vitro and the effect of PCL-HA scaffolds on osteochondral repair in vivo. Here, bone marrow was added to the prepared PCL-HA scaffolds and cultured in chondrogenic medium for 10 weeks. Osteochondral defects were created in the trochlear groove of 29 knees in 17 New Zealand white rabbits, which were then divided into four groups that underwent: implantation of PCL-HA scaffolds (left knee, n = 17; Group 1), microfracture (right knee, n = 6; Group 2), autologous osteochondral transplantation (right knee, n = 6; Group 3), and no treatment (right knee, n = 5; Control). Extracellular matrix produced by bone marrow cells covered the surface and filled the pores of PCL-HA scaffolds after 10 weeks in culture. Moreover, many cell-laden cartilage lacunae were observed, and cartilage matrix was concentrated in the PCL-HA scaffolds. After a 12-week repair period, Group 1 showed excellent vertical and lateral integration with host bone, but incomplete cartilage regeneration and matrix accumulation. An uneven surface of regenerated cartilage and reduced distribution of cartilage matrix were observed in Group 2. In addition, abnormal bone growth and unstable integration between repaired and host tissues were detected. For Group 3, the integration between transplanted and host cartilage was interrupted. Our findings indicate that the PCL-HA scaffolds loaded with bone marrow cells improved chondrogenesis in vitro and implantation of PCL-HA scaffolds for osteochondral repairenhanced integration with host bone. However, cartilage regeneration remained unsatisfactory. The addition of trophic factors or the use of precultured cell-PCL-HA constructs for accelerated osteochondral repair requires further investigation. © The Author(s) 2015.

Porogen-based solid freeform fabrication of polycaprolactone-calcium phosphate scaffolds for tissue engineering.

PubMed

Mondrinos, Mark J; Dembzynski, Robert; Lu, Lin; Byrapogu, Venkata K C; Wootton, David M; Lelkes, Peter I; Zhou, Jack

2006-09-01

Drop on demand printing (DDP) is a solid freeform fabrication (SFF) technique capable of generating microscale physical features required for tissue engineering scaffolds. Here, we report results toward the development of a reproducible manufacturing process for tissue engineering scaffolds based on injectable porogens fabricated by DDP. Thermoplastic porogens were designed using Pro/Engineer and fabricated with a commercially available DDP machine. Scaffolds composed of either pure polycaprolactone (PCL) or homogeneous composites of PCL and calcium phosphate (CaP, 10% or 20% w/w) were subsequently fabricated by injection molding of molten polymer-ceramic composites, followed by porogen dissolution with ethanol. Scaffold pore sizes, as small as 200 microm, were attainable using the indirect (porogen-based) method. Scaffold structure and porosity were analyzed by scanning electron microscopy (SEM) and microcomputed tomography, respectively. We characterized the compressive strength of 90:10 and 80:20 PCL-CaP composite materials (19.5+/-1.4 and 24.8+/-1.3 Mpa, respectively) according to ASTM standards, as well as pure PCL scaffolds (2.77+/-0.26 MPa) fabricated using our process. Human embryonic palatal mesenchymal (HEPM) cells attached and proliferated on all scaffolds, as evidenced by fluorescent nuclear staining with Hoechst 33258 and the Alamar Blue assay, with increased proliferation observed on 80:20 PCL-CaP scaffolds. SEM revealed multilayer assembly of HEPM cells on 80:20 PCL-CaP composite, but not pure PCL, scaffolds. In summary, we have developed an SFF-based injection molding process for the fabrication of PCL and PCL-CaP scaffolds that display in vitro cytocompatibility and suitable mechanical properties for hard tissue repair.

Uniformly-dispersed nanohydroxapatite-reinforced poly(ε-caprolactone) composite films for tendon tissue engineering application.

PubMed

Tong, Shi Yun; Wang, Zuyong; Lim, Poon Nian; Wang, Wilson; Thian, Eng San

2017-01-01

Regeneration of injuries at tendon-to-bone interface (TBI) remains a challenging issue due to the complex tissue composition involving both soft tendon tissues and relatively hard bone tissues. Tissue engineering using polymeric/ceramic composites has been of great interest to generate scaffolds for tissue's healing at TBI. Herein, we presented a novel method to blend polymers and bioceramics for tendon tissue engineering application. A homogeneous composite comprising of nanohydroxyapatite (nHA) particles in poly(ε-caprolactone) (PCL) matrix was obtained using a combination of solvent and mechanical blending process. X-ray diffraction analysis showed that the as-fabricated PCL/nHA composite film retained phase-pure apatite and semi-crystalline properties of PCL. Infrared spectroscopy spectra confirmed that the PCL/nHA composite film exhibited the characteristics functional groups of PCL and nHA, without alteration to the chemical properties of the composite. The incorporation of nHA resulted in PCL/nHA composite film with improved mechanical properties such as Young's Modulus and ultimate tensile stress, which were comparable to that of the native human rotator tendon. Seeding with human tenocytes, cells attached on the PCL/nHA composite film, and after 14days of culturing, these cells could acquire elongated morphology without induced cytotoxicity. PCL/nHA composite film could also result in increased cell metabolism with prolonged culturing, which was comparable to that of the PCL group and higher than that of the nHA group. All these results demonstrated that the developed technique of combining solvent and mechanical blending could be applied to fabricate composite films with potential for tendon tissue engineering applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Plasma cell leukemia: update on biology and therapy.

PubMed

Mina, Roberto; D'Agostino, Mattia; Cerrato, Chiara; Gay, Francesca; Palumbo, Antonio

2017-07-01

Plasma cell leukemia (PCL) is a rare, but very aggressive, plasma cell dyscrasia, representing a distinct clinicopathological entity as compared to multiple myeloma (MM), with peculiar biological and clinical features. A hundred times rarer than MM, the disease course is characterized by short remissions and poor survival. PCL is defined by an increased percentage (>20%) and absolute number (>2 × 10 9 /l) of plasma cells in the peripheral blood. PCL is defined as 'primary' when peripheral plasmacytosis is detected at diagnosis, 'secondary' when leukemization occurs in a patient with preexisting MM. Novel agents have revolutionized the outcomes of MM patients and have been introduced also for the treatment of PCL. Here, we provide an update on biology and treatment options for PCL.

Self-assembly assisted polymerization (SAAP): approaching long multi-block copolymers with an ordered chain sequence and controllable block length.

PubMed

Wu, Chi; Xie, Zuowei; Zhang, Guangzhao; Zi, Guofu; Tu, Yingfeng; Yang, Yali; Cai, Ping; Nie, Ting

2002-12-07

A combination of polymer physics and synthetic chemistry has enabled us to develop self-assembly assisted polymerization (SAAP), leading to the preparation of long multi-block copolymers with an ordered chain sequence and controllable block lengths.

Separation of Poly(styrene-block-t-butyl methacrylate) Copolymers by Various Liquid Chromatography Techniques

PubMed Central

Šmigovec Ljubič, Tina; Pahovnik, David; Žigon, Majda; Žagar, Ema

2012-01-01

The separation of a mixture of three poly(styrene-block-t-butyl methacrylate) copolymers (PS-b-PtBMA), consisting of polystyrene (PS) blocks of similar length and t-butyl methacrylate (PtBMA) blocks of different lengths, was performed using various chromatographic techniques, that is, a gradient liquid chromatography on reversed-phase (C18 and C8) and normal-phase columns, a liquid chromatography under critical conditions for polystyrene as well as a fully automated two-dimensional liquid chromatography that separates block copolymers by chemical composition in the first dimension and by molar mass in the second dimension. The results show that a partial separation of the mixture of PS-b-PtBMA copolymers can be achieved only by gradient liquid chromatography on reversed-phase columns. The coelution of the two block copolymers is ascribed to a much shorter PtBMA block length, compared to the PS block, as well as a small difference in the length of the PtBMA block in two of these copolymers, which was confirmed by SEC-MALS and NMR spectroscopy. PMID:22489207

Electrospun fiber membranes enable proliferation of genetically modified cells

PubMed Central

Borjigin, Mandula; Eskridge, Chris; Niamat, Rohina; Strouse, Bryan; Bialk, Pawel; Kmiec, Eric B

2013-01-01

Polycaprolactone (PCL) and its blended composites (chitosan, gelatin, and lecithin) are well-established biomaterials that can enrich cell growth and enable tissue engineering. However, their application in the recovery and proliferation of genetically modified cells has not been studied. In the study reported here, we fabricated PCL-biomaterial blended fiber membranes, characterized them using physicochemical techniques, and used them as templates for the growth of genetically modified HCT116-19 colon cancer cells. Our data show that the blended polymers are highly miscible and form homogenous electrospun fiber membranes of uniform texture. The aligned PCL nanofibers support robust cell growth, yielding a 2.5-fold higher proliferation rate than cells plated on standard plastic plate surfaces. PCL-lecithin fiber membranes yielded a 2.7-fold higher rate of proliferation, while PCL-chitosan supported a more modest growth rate (1.5-fold higher). Surprisingly, PCL-gelatin did not enhance cell proliferation when compared to the rate of cell growth on plastic surfaces. PMID:23467983

Assessing risk for violence among male and female civil psychiatric patients: the HCR-20, PCL:SV, and VSC.

PubMed

Nicholls, Tonia L; Ogloff, James R P; Douglas, Kevin S

2004-01-01

This study evaluated the predictive validity of violence risk assessments conducted using the HCR-20, the Psychopathy Checklist: Screening Version (PCL:SV), and by the Violence Screening Checklist (VSC) in a sample of 268 involuntarily hospitalized male and female psychiatric patients. Information pertaining to violence and crime was coded from medical charts and correctional records. The HCR-20/PCL:SV evidenced modest non-significant associations in postdictive assessments of inpatient violence among men. Moderate to strong significant associations were found between the HCR-20/PCL:SV and inpatient violence among women. Pseudo-prospective assessments using the HCR-20 and PCL:SV resulted in moderate to large relationships with violence and crime in men and women following community discharge. It is concluded that the VSC is a promising tool for assessing acute inpatient violence risk with men. Findings offer preliminary validation of the predictive validity of the HCR-20 and PCL:SV with female civil psychiatric patients. Copyright 2004 John Wiley & Sons, Ltd.

Multicomponent polymeric nanoparticles enhancing intracellular drug release in cancer cells.

PubMed

Ahmed, Arsalan; Liu, Sen; Pan, Yutong; Yuan, Shanmei; He, Jian; Hu, Yong

2014-12-10

Three kinds of amphiphilic copolymer, that is, poly(ε-caprolactone)-SS-poly(ethylene glycol) (PCL-SS-PEG), poly(ε-caprolactone)-polyethylenimine (PCL-PEI), and poly(ε-caprolactone)-polyethylenimine-folate (PCL-PEI-Fol) were synthesized and self-assembled into surface engineered hybrid nanoparticles (NPs). Morphological studies elucidated the stable, spherical, and uniform sandwich structure of the NPs. PCL-PEI and PCL-SS-PEG segments have introduced pH and reduction responsive characteristics in these NPs, while PCL-PEI-FA copolymers could provide specific targeting capability to cancer cells. The stimuli responsive capabilities of these NPs were carried out. Negative-to-positive charge reversible property, in response to the pH change, was investigated by zeta potential and nuclear magnetic resonance (NMR) measurements. The structure cleavage, due to redox gradient, was studied by dynamic light scattering (DLS) and transmission electron microscopy (TEM). These NPs showed controlled degradation, better drug release, less toxicity, and effective uptake in MCF-7 breast cancer cells. These multifunctional NPs showed promising potential in the treatment of cancer.

The Inclusion of Chitosan in Poly-ε-caprolactone Nanoparticles: Impact on the Delivery System Characteristics and on the Adsorbed Ovalbumin Secondary Structure.

PubMed

Jesus, Sandra; Fragal, Elizangela H; Rubira, Adley F; Muniz, Edvani C; Valente, Artur J M; Borges, Olga

2018-01-01

This report extensively explores the benefits of including chitosan into poly-ε-caprolactone (PCL) nanoparticles (NPs) to obtain an improved protein/antigen delivery system. Blend NPs (PCL/chitosan NPs) showed improved protein adsorption efficacy (84%) in low shear stress and aqueous environment, suggesting that a synergistic effect between PCL hydrophobic nature and the positive charges of chitosan present at the particle surface was responsible for protein interaction. Additionally, thermal analysis suggested the blend NPs were more stable than the isolated polymers and cytotoxicity assays in a primary cell culture revealed chitosan inclusion in PCL NPs reduced the toxicity of the delivery system. A quantitative 6-month stability study showed that the inclusion of chitosan in PCL NPs did not induce a change in adsorbed ovalbumin (OVA) secondary structure characterized by the increase in the unordered conformation (random coil), as it was observed for OVA adsorbed to chitosan NPs. Additionally, the slight conformational changes occurred, are not expected to compromise ovalbumin secondary structure and activity, during a 6-month storage even at high temperatures (45°C). In simulated biological fluids, PCL/chitosan NPs showed an advantageous release profile for oral delivery. Overall, the combination of PCL and chitosan characteristics provide PCL/chitosan NPs valuable features particularly important to the development of vaccines for developing countries, where it is difficult to ensure cold chain transportation and non-parenteral formulations would be preferred.

Synthesis, Characterization, and Visible Light Curing Capacity of Polycaprolactone Acrylate

PubMed Central

Tzeng, Jy-Jiunn; Hsiao, Yi-Ting; Wu, Yun-Ching; Chen, Hsuan; Lee, Shyh-Yuan

2018-01-01

Polycaprolactone (PCL) is drawing increasing attention in the field of medical 3D printing and tissue engineering because of its biodegradability. This study developed polycaprolactone prepolymers that can be cured using visible light. Three PCL acrylates were synthesized: polycaprolactone-530 diacrylate (PCL530DA), glycerol-3 caprolactone triacrylate (Glycerol-3CL-TA), and glycerol-6 caprolactone triacrylate (Glycerol-6CL-TA). PCL530DA has two acrylates, whereas Glycerol-3CL-TA and Glycerol-6CL-TA have three acrylates. The Fourier transform infrared and nuclear magnetic resonance spectra suggested successful synthesis of all PCL acrylates. All are liquid at room temperature and can be photopolymerized into a transparent solid after exposure to 470 nm blue LED light using 1% camphorquinone as photoinitiator and 2% dimethylaminoethyl methacrylate as coinitiator. The degree of conversion for all PCL acrylates can reach more than 80% after 1 min of curing. The compressive modulus of PCL530DA, Glycerol-3CL-TA, and Glycerol-6CL-TA is 65.7 ± 12.7, 80.9 ± 6.1, and 32.1 ± 4.1 MPa, respectively, and their compressive strength is 5.3 ± 0.29, 8.3 ± 0.18, and 3.0 ± 0.53 MPa, respectively. Thus, all PCL acrylates synthesized in this study can be photopolymerized and because of their solid structure and low viscosity, they are applicable to soft tissue engineering and medical 3D printing. PMID:29854803

Evaluating the Effectiveness of POGIL-PCL Workshops

ERIC Educational Resources Information Center

Stegall, Stacy L.; Grushow, Alexander; Whitnell, Robert; Hunnicutt, Sally S.

2016-01-01

The POGIL-PCL (Process-Oriented Guided Inquiry Learning in the Physical Chemistry Laboratory) project has developed a series of workshops to introduce faculty to POGIL-PCL and to facilitate the development of new experiments. More than 60 faculty members from various institutions have attended these workshops. Workshop participants were surveyed…

Guided-Inquiry Experiments for Physical Chemistry: The POGIL-PCL Model

ERIC Educational Resources Information Center

Hunnicutt, Sally S.; Grushow, Alexander; Whitnell, Robert

2015-01-01

The POGIL-PCL project implements the principles of process-oriented, guided-inquiry learning (POGIL) in order to improve student learning in the physical chemistry laboratory (PCL) course. The inquiry-based physical chemistry experiments being developed emphasize modeling of chemical phenomena. In each experiment, students work through at least…

Growth of long triisopropylsilylethynyl pentacene (TIPS-PEN) nanofibrils in a polymer thin film during spin-coating.

PubMed

Park, Minwoo; Min, Yuho; Lee, Yu-Jeong; Jeong, Unyong

2014-03-01

This study demonstrates the growth of long triisopropylsilyethynyl pentacene (TIPS-PEN) nanofibrils in a thin film of a crystalline polymer, poly(ε-caprolactone) (PCL). During spin-coating, TIPS-PEN molecules are locally extracted around the PCL grain boundaries and they crystallize into [010] direction forming long nanofibrils. Molecular weight of PCL and weight fraction (α) of TIPS-PEN in PCL matrix are key factors to the growth of nanofibrils. Long high-quality TIPS-PEN nanofibrils are obtained with high-molecular-weight PCL and at the α values in the range of 0.03-0.1. The long nanofibrils are used as an active layer in a field-effect organic transistor. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

3D Printed Polycaprolactone Carbon Nanotube Composite Scaffolds for Cardiac Tissue Engineering.

PubMed

Ho, Chee Meng Benjamin; Mishra, Abhinay; Lin, Pearlyn Teo Pei; Ng, Sum Huan; Yeong, Wai Yee; Kim, Young-Jin; Yoon, Yong-Jin

2017-04-01

Fabrication of tissue engineering scaffolds with the use of novel 3D printing has gained lot of attention, however systematic investigation of biomaterials for 3D printing have not been widely explored. In this report, well-defined structures of polycaprolactone (PCL) and PCL- carbon nanotube (PCL-CNT) composite scaffolds have been designed and fabricated using a 3D printer. Conditions for 3D printing has been optimized while the effects of varying CNT percentages with PCL matrix on the thermal, mechanical and biological properties of the printed scaffolds are studied. Raman spectroscopy is used to characterise the functionalized CNTs and its interactions with PCL matrix. Mechanical properties of the composites are characterised using nanoindentation. Maximum peak load, elastic modulus and hardness increases with increasing CNT content. Differential scanning calorimetry (DSC) studies reveal the thermal and crystalline behaviour of PCL and its CNT composites. Biodegradation studies are performed in Pseudomonas Lipase enzymatic media, showing its specificity and effect on degradation rate. Cell imaging and viability studies of H9c2 cells from rat origin on the scaffolds are performed using fluorescence imaging and MTT assay, respectively. PCL and its CNT composites are able to show cell proliferation and have the potential to be used in cardiac tissue engineering. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Biodegradable polycaprolactone (PCL) nanosphere encapsulating superoxide dismutase and catalase enzymes.

PubMed

Singh, Sushant; Singh, Abhay Narayan; Verma, Anil; Dubey, Vikash Kumar

2013-12-01

Biodegradable polycaprolactone (PCL) nanosphere encapsulating superoxide dismutase (SOD) and catalase (CAT) were successfully synthesized using double emulsion (w/o/w) solvent evaporation technique. Characterization of the nanosphere using dynamic light scattering, field emission scanning electron microscope, and Fourier transform infrared spectroscopy revealed a spherical-shaped nanosphere in a size range of 812 ± 64 nm with moderate protein encapsulation efficiency of 55.42 ± 3.7 % and high in vitro protein release. Human skin HaCat cells were used for analyzing antioxidative properties of SOD- and CAT-encapsulated PCL nanospheres. Oxidative stress condition in HaCat cells was optimized with exposure to hydrogen peroxide (H2O2; 1 mM) as external stress factor and verified through reactive oxygen species (ROS) analysis using H2DCFDA dye. PCL nanosphere encapsulating SOD and CAT together indicated better antioxidative defense against H2O2-induced oxidative stress in human skin HaCat cells in comparison to PCL encapsulating either SOD or CAT alone as well as against direct supplement of SOD and CAT protein solution. Increase in HaCat cells SOD and CAT activities after treatment hints toward uptake of PCL nanosphere into the human skin HaCat cells. The result signifies the role of PCL-encapsulating SOD and CAT nanosphere in alleviating oxidative stress.

Physical and Biological Modification of Polycaprolactone Electrospun Nanofiber by Panax Ginseng Extract for Bone Tissue Engineering Application.

PubMed

Pajoumshariati, Seyedramin; Yavari, Seyedeh Kimia; Shokrgozar, Mohammad Ali

2016-05-01

Medicinal plants as a therapeutic agent with osteogenic properties can enhance fracture-healing process. In this study, the osteo-inductive potential of Asian Panax Ginseng root extract within electrospun polycaprolactone (PCL) based nanofibers has been investigated. Scanning electron microscopy images revealed that all nanofibers were highly porous and beadles with average diameter ranging from 250 to 650 nm. The incorporation of ginseng extract improved the physical characteristics (i.e., hydrophilicity) of PCL nanofibers, as well as the mechanical properties. Although ginseng extract increased the degradation rate of pure PCL nanofibers, the porous structure and morphology of fibers did not change significantly after 42 days. It was found that nanofibrous scaffolds containing ginseng extract had higher proliferation (up to ~1.5 fold) compared to the pristine PCL. The qRT-PCR analysis demonstrated the addition of ginseng extract into PCL nanofibers induced significant expression of osteogenic genes (Osteocalcin, Runx-2 and Col-1) in MSCs in a concentration dependent manner. Moreover, higher calcium content, alkaline phosphatase activity and higher mineralization of MSCs were observed compared to the pristine PCL fibers. Our results indicated the promising potential of ginseng extract as an additive to enhance osteo-inductivity, mechanical and physical properties of PCL nanofibers for bone tissue engineering application.

Nanoformulation of D-α-tocopheryl polyethylene glycol 1000 succinate-b-poly(ε-caprolactone-ran-glycolide) diblock copolymer for breast cancer therapy.

PubMed

Huang, Laiqiang; Chen, Hongbo; Zheng, Yi; Song, Xiaosong; Liu, Ranyi; Liu, Kexin; Zeng, Xiaowei; Mei, Lin

2011-10-01

The purpose of this research was to develop formulation of docetaxel-loaded biodegradable TPGS-b-(PCL-ran-PGA) nanoparticles for breast cancer chemotherapy. A novel diblock copolymer, d-α-tocopheryl polyethylene glycol 1000 succinate-b-poly(ε-caprolactone-ran-glycolide) [TPGS-b-(PCL-ran-PGA)], was synthesized from ε-caprolactone, glycolide and d-α-tocopheryl polyethylene glycol 1000 succinate by ring-opening polymerization using stannous octoate as catalyst. The obtained copolymers were characterized by (1)H NMR, GPC and TGA. The docetaxel-loaded TPGS-b-(PCL-ran-PGA) nanoparticles were prepared and characterized. The data showed that the fluorescence TPGS-b-(PCL-ran-PGA) nanoparticles could be internalized by MCF-7 cells. The TPGS-b-(PCL-ran-PGA) nanoparticles achieved significantly higher level of cytotoxicity than commercial Taxotere®. MCF-7 xenograft tumor model on SCID mice showed that docetaxel formulated in the TPGS-b-(PCL-ran-PGA) nanoparticles could effectively inhibit the growth of tumor over a longer period of time than Taxotere® at the same dose. In conclusion, the TPGS-b-(PCL-ran-PGA) copolymer could be acted as a novel and potential biologically active polymeric material for nanoformulation in breast cancer chemotherapy. This journal is © The Royal Society of Chemistry 2011

Bone Regeneration after Treatment with Covering Materials Composed of Flax Fibers and Biodegradable Plastics: A Histological Study in Rats

PubMed Central

Gedrange, Tomasz

2016-01-01

The aim of this study was to examine the osteogenic potential of new flax covering materials. Bone defects were created on the skull of forty rats. Materials of pure PLA and PCL and their composites with flax fibers, genetically modified producing PHB (PLA-transgen, PCL-transgen) and unmodified (PLA-wt, PCL-wt), were inserted. The skulls were harvested after four weeks and subjected to histological examination. The percentage of bone regeneration by using PLA was less pronounced than after usage of pure PCL in comparison with controls. After treatment with PCL-transgen, a large amount of new formed bone could be found. In contrast, PCL-wt decreased significantly the bone regeneration, compared to the other tested groups. The bone covers made of pure PLA had substantially less influence on bone regeneration and the bone healing proceeded with a lot of connective tissue, whereas PLA-transgen and PLA-wt showed nearly comparable amount of new formed bone. Regarding the histological data, the hypothesis could be proposed that PCL and its composites have contributed to a higher quantity of the regenerated bone, compared to PLA. The histological studies showed comparable bone regeneration processes after treatment with tested covering materials, as well as in the untreated bone lesions. PMID:27597965

Bone Regeneration after Treatment with Covering Materials Composed of Flax Fibers and Biodegradable Plastics: A Histological Study in Rats.

PubMed

Gredes, Tomasz; Kunath, Franziska; Gedrange, Tomasz; Kunert-Keil, Christiane

2016-01-01

The aim of this study was to examine the osteogenic potential of new flax covering materials. Bone defects were created on the skull of forty rats. Materials of pure PLA and PCL and their composites with flax fibers, genetically modified producing PHB (PLA-transgen, PCL-transgen) and unmodified (PLA-wt, PCL-wt), were inserted. The skulls were harvested after four weeks and subjected to histological examination. The percentage of bone regeneration by using PLA was less pronounced than after usage of pure PCL in comparison with controls. After treatment with PCL-transgen, a large amount of new formed bone could be found. In contrast, PCL-wt decreased significantly the bone regeneration, compared to the other tested groups. The bone covers made of pure PLA had substantially less influence on bone regeneration and the bone healing proceeded with a lot of connective tissue, whereas PLA-transgen and PLA-wt showed nearly comparable amount of new formed bone. Regarding the histological data, the hypothesis could be proposed that PCL and its composites have contributed to a higher quantity of the regenerated bone, compared to PLA. The histological studies showed comparable bone regeneration processes after treatment with tested covering materials, as well as in the untreated bone lesions.

Cognitive deficits are a matter of emotional context: inflexible strategy use mediates context-specific learning impairments in OCD.

PubMed

Zetsche, Ulrike; Rief, Winfried; Westermann, Stefan; Exner, Cornelia

2015-01-01

The present study examines the interplay between cognitive deficits and emotional context in obsessive-compulsive disorder (OCD) and social phobia (SP). Specifically, this study examines whether the inflexible use of efficient learning strategies in an emotional context underlies impairments in probabilistic classification learning (PCL) in OCD, and whether PCL impairments are specific to OCD. Twenty-three participants with OCD, 30 participants with SP and 30 healthy controls completed a neutral and an OCD-specific PCL task. OCD participants failed to adopt efficient learning strategies and showed fewer beneficial strategy switches than controls only in an OCD-specific context, but not in a neutral context. Additionally, OCD participants did not show any explicit memory impairments. Number of beneficial strategy switches in the OCD-specific task mediated the difference in PCL performance between OCD and control participants. Individuals with SP were impaired in both PCL tasks. In contrast to neuropsychological models postulating general cognitive impairments in OCD, the present findings suggest that it is the interaction between cognition and emotion that is impaired in OCD. Specifically, activated disorder-specific fears may impair the flexible adoption of efficient learning strategies and compromise otherwise unimpaired PCL. Impairments in PCL are not specific to OCD.

Hydroxyapatite/poly(epsilon-caprolactone) composite coatings on hydroxyapatite porous bone scaffold for drug delivery.

PubMed

Kim, Hae-Won; Knowles, Jonathan C; Kim, Hyoun-Ee

2004-01-01

Hydroxyapatite (HA) porous scaffold was coated with HA and polycaprolactone (PCL) composites, and antibiotic drug tetracycline hydrochloride was entrapped within the coating layer. The HA scaffold obtained by a polymeric reticulate method, possessed high porosity ( approximately 87%) and controlled pore size (150-200 microm). Such a well-developed porous structure facilitated usage in a drug delivery system due to its high surface area and blood circulation efficiency. The PCL polymer, as a coating component, was used to improve the brittleness and low strength of the HA scaffold, as well to effectively entrap the drug. To improve the osteoconductivity and bioactivity of the coating layer, HA powder was hybridized with PCL solution to make the HA-PCL composite coating. With alteration in the coating concentration and HA/PCL ratio, the morphology, mechanical properties, and biodegradation behavior were investigated. Increasing the concentration rendered the stems thicker and some pores to be clogged; as well increasing the HA/PCL ratio made the coating surface be rough due to the large amount of HA particles. However, for all concentrations and compositions, uniform coatings were formed, i.e., with the HA particles being dispersed homogeneously in the PCL sheet. With the composite coating, the mechanical properties, such as compressive strength and elastic modulus were improved by several orders of magnitude. These improvements were more significant with thicker coatings, while little difference was observed with the HA/PCL ratio. The in vitro biodegradation of the composite coatings in the phosphate buffered saline solution increased linearly with incubation time and the rate differed with the coating concentration and the HA/PCL ratio; the higher concentration and HA amount caused the increased biodegradation. At short period (<2 h), about 20-30% drug was released especially due to free drug at the coating surface. However, the release rate was sustained for prolonged periods and was highly dependent on the degree of coating dissolution, suggesting the possibility of a controlled drug release in the porous scaffold with HA+PCL coating.

Tibiofemoral and patellofemoral joint 3D-kinematics in patients with posterior cruciate ligament deficiency compared to healthy volunteers.

PubMed

von Eisenhart-Rothe, Ruediger; Lenze, Ulrich; Hinterwimmer, Stefan; Pohlig, Florian; Graichen, Heiko; Stein, Thomas; Welsch, Frederic; Burgkart, Rainer

2012-11-26

The posterior cruciate ligament (PCL) plays an important role in maintaining physiological kinematics and function of the knee joint. To date mainly in-vitro models or combined magnetic resonance and fluoroscopic systems have been used for quantifying the importance of the PCL. We hypothesized, that both tibiofemoral and patellofemoral kinematic patterns are changed in PCL-deficient knees, which is increased by isometric muscle flexion. Therefore the aim of this study was to simultaneously investigate tibiofemoral and patellofemoral 3D kinematics in patients suffering from PCL deficiency during different knee flexion angles and under neuromuscular activation. We enrolled 12 patients with isolated PCL-insufficiency as well as 20 healthy volunteers. Sagittal MR-images of the knee joint were acquired in different positions of the knee joint (0°, 30°, 90° flexion, with and without flexing isometric muscle activity) on a 0.2 Tesla open MR-scanner. After segmentation of the patella, femur and tibia local coordinate systems were established to define the spatial position of these structures in relation to each other. At full extension and 30° flexion no significant difference was observed in PCL-deficient knee joints neither for tibiofemoral nor for patellofemoral kinematics. At 90° flexion the femur of PCL-deficient patients was positioned significantly more anteriorly in relation to the tibia and both, the patellar tilt and the patellar shift to the lateral side, significantly increased compared to healthy knee joints. While no significant effect of isometric flexing muscle activity was observed in healthy individuals, in PCL-deficient knee joints an increased paradoxical anterior translation of the femur was observed at 90° flexion compared to the status of muscle relaxation. Significant changes in tibiofemoral and patellofemoral joint kinematics occur in patients with isolated PCL-insufficiency above 30 degrees of flexion compared to healthy volunteers. Since this could be one reasonable mechanism in the development of osteoarthritis (OA) our results might help to understand the long-term development of tibiofemoral and/or patellofemoral OA in PCL-insufficient knee joints.

Electrospun fibrous scaffolds combined with nanoscale hydroxyapatite induce osteogenic differentiation of human periodontal ligament cells

PubMed Central

Wu, Xiaonan; Miao, Leiying; Yao, Yingfang; Wu, Wenlei; Liu, Yu; Chen, Xiaofeng; Sun, Weibin

2014-01-01

Periodontal repair is a complex process in which regeneration of alveolar bone is a vital component. The aim of this study was to develop a biodegradable scaffold with good biocompatibility and osteoinductive ability. Two types of composite fibrous scaffolds were produced by electrospinning, ie, type I collagen/poly(ε-caprolactone) (COL/PCL) and type I collagen/poly(ε-caprolactone)/nanoscale hydroxyapatite (COL/PCL/nHA) with an average fiber diameter of about 377 nm. After a simulated body fluid (SBF) immersion test, the COL/PCL/nHA-SBF scaffold developed a rough surface because of the calcium phosphate deposited on the fibers, suggesting that the presence of nHA promoted the mineralization potential of the scaffold. Energy dispersive X-ray spectroscopy clearly showed the calcium and phosphorus content in the COL/PCL/nHA and COL/PCL/nHA-SBF scaffolds, confirming the findings of nHA and calcium phosphate precipitation on scanning electron micrographs. Water contact analysis revealed that nHA could improve the hydrophilic nature of the COL/PCL/nHA-SBF scaffold. The morphology of periodontal ligament cells cultured on COL/PCL-SBF and COL/PCL/nHA-SBF was evaluated by scanning electron microscopy. The results showed that cells adhered to either type of scaffold and were slightly spindle-shaped in the beginning, then extended gradually with stretched filopodia, indicating an ability to fill the fiber pores. A Cell Counting Kit-8 assay showed that both scaffolds supported cell proliferation. However, real-time quantitative polymerase chain reaction analysis showed that expression of the bone-related markers, alkaline phosphatase and osteocalcin, was upregulated only on the COL/PCL/nHA-SBF scaffold, indicating that this scaffold had the ability to induce osteogenic differentiation of periodontal ligament cells. In this study, COL/PCL/nHA-SBF produced by electrospinning followed by biomimetic mineralization had combined electrospun fibers with nHA in it. This scaffold has good biocompatibility and osteoinductive ability as a result of the characteristics of nHA, so could be innovatively applied to periodontal tissue engineering as a potential scaffold. PMID:25206304

Polycaprolactone electrospun mesh conjugated with an MSC affinity peptide for MSC homing in vivo.

PubMed

Shao, Zhenxing; Zhang, Xin; Pi, Yanbin; Wang, Xiaokun; Jia, Zhuqing; Zhu, Jingxian; Dai, Linghui; Chen, Wenqing; Yin, Ling; Chen, Haifeng; Zhou, Chunyan; Ao, Yingfang

2012-04-01

Mesenchymal stem cell (MSC) is a promising cell source candidate in tissue engineering (TE) and regenerative medicine. However, the inability to target MSCs in tissues of interest with high efficiency and engraftment has become a significant barrier for MSC-based therapies. The mobilization and transfer of MSCs to defective/damaged sites in tissues or organs in vivo with high efficacy and efficiency has been a major concern. In the present study, we identified a peptide sequence (E7) with seven amino acids through phage display technology, which has a high specific affinity to bone marrow-derived MSCs. Subsequent analysis suggested that the peptide could efficiently interact specifically with MSCs without any species specificity. Thereafter, E7 was covalently conjugated onto polycaprolactone (PCL) electrospun meshes to construct an "MSC-homing device" for the recruitment of MSCs both in vitro and in vivo. The E7-conjugated PCL electrospun meshes were implanted into a cartilage defect site of rat knee joints, combined with a microfracture procedure to mobilize the endogenous MSCs. After 7 d of implantation, immunofluorescence staining showed that the cells grown into the E7-conjugated PCL electrospun meshes yielded a high positive rate for specific MSC surface markers (CD44, CD90, and CD105) compared with those in arginine-glycine-aspartic acid (RGD)-conjugated PCL electrospun meshes (63.67% vs. 3.03%; 59.37% vs. 2.98%; and 61.45% vs. 3.82%, respectively). Furthermore, the percentage of CD68 positive cells in the E7-conjugated PCL electrospun meshes was much lower than that in the RGD-conjugated PCL electrospun meshes (5.57% vs. 53.43%). This result indicates that E7-conjugated PCL electrospun meshes absorb much less inflammatory cells in vivo than RGD-conjugated PCL electrospun meshes. The results of the present study suggest that the identified E7 peptide sequence has a high specific affinity to MSCs. Covalently conjugating this peptide on the synthetic PCL mesh significantly enhanced the MSC recruitment of PCL in vivo. This method provides a wide range of potential applications in TE. Copyright © 2012 Elsevier Ltd. All rights reserved.

Development and properties of duplex MgF2/PCL coatings on biodegradable magnesium alloy for biomedical applications.

PubMed

Makkar, Preeti; Kang, Hoe Jin; Padalhin, Andrew R; Park, Ihho; Moon, Byoung-Gi; Lee, Byong Taek

2018-01-01

The present work addresses the performance of polycaprolactone (PCL) coating on fluoride treated (MgF2) biodegradable ZK60 magnesium alloy (Mg) for biomedical application. MgF2 conversion layer was first produced by immersing Mg alloy substrate in hydrofluoric acid solution. The outer PCL coating was then prepared using dip coating technique. Morphology, elements profile, phase structure, roughness, mechanical properties, invitro corrosion, and biocompatibility of duplex MgF2/PCL coating were then characterized and compared to those of fluoride coated and uncoated Mg samples. The invivo degradation behavior and biocompatibility of duplex MgF2/PCL coating with respect to ZK60 Mg alloy were also studied using rabbit model for 2 weeks. SEM and TEM analysis showed that the duplex coating was uniform and comprised of porous PCL film (~3.3 μm) as upper layer with compact MgF2 (~2.2 μm) as inner layer. No significant change in microhardness was found on duplex coating compared with uncoated ZK60 Mg alloy. The duplex coating showed improved invitro corrosion resistance than single layered MgF2 or uncoated alloy samples. The duplex coating also resulted in better cell viability, cell adhesion, and cell proliferation compared to fluoride coated or uncoated alloy. Preliminary invivo studies indicated that duplex MgF2/PCL coating reduced the degradation rate of ZK60 Mg alloy and exhibited good biocompatibility. These results suggested that duplex MgF2/PCL coating on magnesium alloy might have great potential for orthopedic applications.

A novel biodegradable PCL film for tendon reconstruction: Achilles tendon defect model in rats.

PubMed

Kazimoğlu, C; Bölükbaşi, S; Kanatli, U; Senköylü, A; Altun, N S; Babaç, C; Yavuz, H; Pişkin, E

2003-09-01

This study aims to investigate applicability of poly(epsilon-caprolactone) (PCL) biodegradable films for repair of gaps in Achilles tendons in a rat model, also comparing surgical repair versus no repair approaches. PCL was synthesized with tailor-made properties, then, PCL films were prepared by solvent casting. Seventy-five outbred Sprague-Dawley rats were randomly allocated into five groups: (i) sham operated (skin incision only); (ii) no repair (complete division of the Achilles tendon and plantaris tendon without repair); (iii) Achilles repair (with a modified Kessler type suture); and (iv) plasty of Achilles tendon defects with the biodegradable PCL films, and (v) animals subjected to 1 cm mid-substance defect with no repair. Functional performance was determined from the measurements of hindpaw prints utilizing the Achilles functional index. The animals were killed 8 weeks after surgery and histological and biomechanical evaluations were made. All groups subjected to Achilles tendon division had a significant functional impairment that gradually improved so that by day 28 there were no functional impairments in any group whereas animals with a defect remained impaired. The magnitude of the biomechanical and morphological changes at postoperative 8 weeks were similar for no repair group (conservative), Achilles repair group and tendonplasty group (biodegradable PCL film group). The initial rate of functional recovery was significantly different for primary suture, Achilles repair group and PCL film group (p>0.01). But, at the 28th day, functional recovery was quite similar to the other groups. In summary, our results suggest that the PCL film can be an alternative biomaterial for tendon replacement.

Intra-articular pathology associated with isolated posterior cruciate ligament injury on MRI.

PubMed

Ringler, Michael D; Shotts, Ezekiel E; Collins, Mark S; Howe, B Matthew

2016-12-01

Unlike with anterior cruciate ligament injury, little is known about the prevalence of intra-articular pathology associated with isolated posterior cruciate ligament (PCL) injury in the knee. The objectives of this study were to characterize and identify the frequency of meniscal tears and osteochondral injuries in these patients, and to see if management might be affected. Altogether, 48 knee MRI exams with isolated PCL tears were evaluated for the presence of: grade and location of PCL tear, meniscal tear, articular chondral lesion, bone bruise, and fracture. Comparisons between PCL tear grade and location, as well as mechanism of injury when known, with the presence of various intra-articular pathologies, were made using the chi-square or Fisher's exact test as appropriate. In all, 69 % of isolated PCL tears occur in the midsubstance, 27 % proximally. Meniscal tears were seen in 25 % of knees, involving all segments of both menisci, except for the anterior horn medial meniscus. Altogether, 23 % had focal cartilage lesions, usually affecting the central third medial femoral condyle and medial trochlea, while 12.5 % of knees had fractures, and 48 % demonstrated bone bruises, usually involving the central to anterior tibiofemoral joint. The presence of a fracture (p = 0.0123) and proximal location of PCL tear (p = 0.0016) were both associated with the hyperextension mechanism of injury. There were no statistically significant associations between PCL tear grade and presence of intra-articular abnormality. Potentially treatable meniscal tears and osteochondral injuries are relatively prevalent, and demonstrable on MRI in patients with isolated acute PCL injury of the knee.

Development and properties of duplex MgF2/PCL coatings on biodegradable magnesium alloy for biomedical applications

PubMed Central

Makkar, Preeti; Kang, Hoe Jin; Padalhin, Andrew R.; Park, Ihho; Moon, Byoung-Gi

2018-01-01

The present work addresses the performance of polycaprolactone (PCL) coating on fluoride treated (MgF2) biodegradable ZK60 magnesium alloy (Mg) for biomedical application. MgF2 conversion layer was first produced by immersing Mg alloy substrate in hydrofluoric acid solution. The outer PCL coating was then prepared using dip coating technique. Morphology, elements profile, phase structure, roughness, mechanical properties, invitro corrosion, and biocompatibility of duplex MgF2/PCL coating were then characterized and compared to those of fluoride coated and uncoated Mg samples. The invivo degradation behavior and biocompatibility of duplex MgF2/PCL coating with respect to ZK60 Mg alloy were also studied using rabbit model for 2 weeks. SEM and TEM analysis showed that the duplex coating was uniform and comprised of porous PCL film (~3.3 μm) as upper layer with compact MgF2 (~2.2 μm) as inner layer. No significant change in microhardness was found on duplex coating compared with uncoated ZK60 Mg alloy. The duplex coating showed improved invitro corrosion resistance than single layered MgF2 or uncoated alloy samples. The duplex coating also resulted in better cell viability, cell adhesion, and cell proliferation compared to fluoride coated or uncoated alloy. Preliminary invivo studies indicated that duplex MgF2/PCL coating reduced the degradation rate of ZK60 Mg alloy and exhibited good biocompatibility. These results suggested that duplex MgF2/PCL coating on magnesium alloy might have great potential for orthopedic applications. PMID:29608572

A comprehensive examination of the psychometric properties of the Hare Psychopathy Checklist-Revised in a Canadian multisite sample of indigenous and non-indigenous offenders.

PubMed

Olver, Mark E; Neumann, Craig S; Sewall, Lindsay A; Lewis, Kathy; Hare, Robert D; Wong, Stephen C P

2018-06-01

The present study examined the psychometric properties of Hare Psychopathy Checklist-Revised (PCL-R; Hare, 2003) scores in a multisite sample of 1,163 federally incarcerated Canadian indigenous and non-indigenous offenders from the Prairie Region of the Correctional Service of Canada. The research occurred against the backdrop of the Ewert v. Canada (2015) matter, in which the PCL-R was originally impugned in Federal Court for use with indigenous persons (later overturned in Canada v. Ewert, 2016). Indigenous men scored higher than non-indigenous men on most components of the PCL-R and had higher rates of recidivism, irrespective of follow-up. Discrimination analyses, however, supported the predictive efficacy of PCL-R total, factor, and facet scores for violent and general recidivism across both ancestral groups, with most group differences in area under the curve (AUC) magnitudes being small and nonsignificant. Calibration analyses demonstrated that higher PCL-R scores were associated with higher rates of general and violent recidivism for both ancestral groups, although higher recidivism rates were observed and estimated for indigenous men at specific PCL-R score thresholds. Confirmatory factor analyses supported the 4-factor model of psychopathy and hence, structural invariance, of PCL-R scores across ancestral groups. Structural equation modeling affirmed the predictive efficacy of the 4-factor model for recidivism. We discuss these findings in terms of clinical applications of the PCL-R and the psychopathy construct in general, with male offenders of indigenous ancestry. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

PCL-R Psychopathy Predicts Disruptive Behavior Among Male Offenders in a Dutch Forensic Psychiatric Hospital

ERIC Educational Resources Information Center

Hildebrand, Martin; De Ruiter, Corine; Nijman, Henk

2004-01-01

In this study, the relationship between psychopathy, according to the Dutch language version of Hare's Psychopathy Checklist-Revised (PCL-R), and various types of disruptive behavior during inpatient forensic psychiatric treatment is investigated. Ninety-two male participants were administered the PCL-R following admission to an inpatient forensic…

Polycaprolactone/glass bioabsorbable implant in a rabbit humerus fracture model.

PubMed

Lowry, K J; Hamson, K R; Bear, L; Peng, Y B; Calaluce, R; Evans, M L; Anglen, J O; Allen, W C

1997-09-15

Research in improved materials and methods for internal fixation has centered on internal fixators made of bioabsorbable materials such as polylactic acid, polyglycolic acid, and polyparadioxanone. These materials have two problems: the first is a postoperative complication related to a delayed inflammatory response; and the second is low strength characteristics. An alternative material developed to alleviate these problems is a composite of phosphate glass fibers embedded in the polymer polycaprolactone, referred to as PCL. In this study, intramedullary pins made of PCL were compared to stainless steel pins in a rabbit humerus osteotomy model. Specimens were harvested at 0, 6, and 12 weeks postoperatively, radiographs and mechanical testing to failure were performed at each time interval, and tissue was examined microscopically at 6 and 12 weeks. Histologic results showed PCL pins to be well tolerated with minimal inflammation around the pin. Mechanical testing revealed the PCL fixation to be weaker initially than the stainless steel fixation. There was significant stress shielding of stainless-steel-healed rabbit humeri when compared to the PCL/bone humeri. All osteotomies immobilized with PCL healed with abundant periosteal callus production.

Laminin- and basement membrane-polycaprolactone blend nanofibers as a scaffold for regenerative medicine.

PubMed

Neal, Rebekah A; Lenz, Steven M; Wang, Tiffany; Abebayehu, Daniel; Brooks, Benjamin P C; Ogle, Roy C; Botchwey, Edward A

2014-09-01

Mimicking one or more components of the basement membrane (BM) holds great promise for overcoming insufficiencies in tissue engineering therapies. We have electrospun laminin nanofibers (NFs) isolated from the murine Engelbreth-Holm Swarm (EHS) tumor and evaluated them as a scaffold for embryonic stem cell culture. Seeded human embryonic stem cells were found to better maintain their undifferentiated, colony environment when cultured on laminin NFs compared to laminin mats, with 75% remaining undifferentiated on NFs. Mouse embryonic stem cells cultured on 10% laminin-polycaprolactone (PCL) NFs maintained their colony formation for twice as long without passage compared to those on PCL or gelatin substrates. In addition, we have established a protocol for electrospinning reconstituted basement membrane aligned (RBM)-PCL NFs within 10° of angular deviation. Neuron-like PC12 cells show significantly greater attachment (p < 0.001) and percentage of neurite-extending cells in vitro on 10% RBM-PCL NFs when compared to 1% and 0% RBM-PCL NFs (p < 0.015 and p < 0.001, respectively). Together, these results implicate laminin- and RBM-PCL scaffolds as a promising biomimetic substrate for regenerative medicine applications.

Elastic poly(ε-caprolactone)-polydimethylsiloxane copolymer fibers with shape memory effect for bone tissue engineering.

PubMed

Kai, Dan; Prabhakaran, Molamma P; Chan, Benjamin Qi Yu; Liow, Sing Shy; Ramakrishna, Seeram; Xu, Fujian; Loh, Xian Jun

2016-02-02

A porous shape memory scaffold with biomimetic architecture is highly promising for bone tissue engineering applications. In this study, a series of new shape memory polyurethanes consisting of organic poly(ε-caprolactone) (PCL) segments and inorganic polydimethylsiloxane (PDMS) segments in different ratios (9 : 1, 8 : 2 and 7 : 3) was synthesised. These PCL-PDMS copolymers were further engineered into porous fibrous scaffolds by electrospinning. With different ratios of PCL: PDMS, the fibers showed various fiber diameters, thermal behaviour and mechanical properties. Even after being processed into fibrous structures, these PCL-PDMS copolymers maintained their shape memory properties, and all the fibers exhibited excellent shape recovery ratios of  >90% and shape fixity ratios of  >92% after 7 thermo-mechanical cycles. Biological assay results corroborated that the fibrous PCL-PDMS scaffolds were biocompatible by promoting osteoblast proliferation, functionally enhanced biomineralization-relevant alkaline phosphatase expression and mineral deposition. Our study demonstrated that the PCL-PDMS fibers with excellent shape memory properties are promising substrates as bioengineered grafts for bone regeneration.

Investigation of the combustion kinetics and polycyclic aromatic hydrocarbon emissions from polycaprolactone combustion.

PubMed

Chien, Y C; Yang, S H

2013-01-01

Polycaprolactone (PCL) is one of the most attractive biodegradable plastics that has been widely used in medicine and agriculture fields. Because of the large increase in biodegradable plastics usage, the production of waste biodegradable plastics will be increasing dramatically, producing a growing environmental problem. Generally, waste PCL is collected along with municipal solid wastes and then incinerated. This study investigates the combustion kinetics and emission factors of 16 US Environmental Protection Agency (EPA) priority polycyclic aromatic hydrocarbons (PAHs) in the PCL combustion. Experimentally, two reactions are involved in the PCL combustion process, possibly resulting in the emission of carbon dioxide, propanal, protonated caprolactone and very small amounts of PAH produced by incomplete combustion. The intermediate products may continuously be oxidized to form CO2. The emission factors for 16 US EPA priority PAHs are n.d. -2.95 microg/g, which are much lower than those of poly lactic acid and other plastics combustion. The conversion of PCL is 100%. Results from this work suggest that combustion is a good choice for the waste PCL disposal.

Banded Spherulitic Morphology in Blends of Poly(propylene fumarate) and Poly( -caprolactone) and Interaction with MC3T3-E1 Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Kan; Jesse, Stephen; Wang, Shanfeng

2012-01-01

The thermal properties, morphological development, crystallization behavior, and miscibility of semicrystalline PCL and its 25, 50, and 75 wt% blends with amorphous PPF in spin-coated thin films crystallized at various crystallization temperatures (T{sub c}) from 25 to 52 C are investigated. The surface roughness of PPF/PCL ({phi}{sub PCL} = 75%) films increases with increasing T{sub c} and consequently the adsorption of serum proteins is also increased. No significant variance is found in surface hydrophilicity or in mouse MC3T3-E1 cell attachment, spreading, and proliferation on PPF/PCL ({phi}{sub PCL} = 75%) films crystallized isothermally at 25, 37, and 45 C, because ofmore » low ridge height, nonuniformity in structures, and PPF surface segregation« less

Low Prevalence of Anterior and Posterior Cruciate Ligament Injuries in Patients With Achondroplasia.

PubMed

Brooks, Jaysson T; Ramji, Alim F; Lyapustina, Tatyana A; Yost, Mary T; Ain, Michael C

2017-01-01

Anterior cruciate ligament (ACL) and posterior cruciate ligament (PCL) injuries and their subsequent reconstructions are common in the general population, but there has been no research regarding ACL or PCL injuries in patients with achondroplasia, the most common skeletal dysplasia. Our goals were to (1) evaluate the prevalence of ACL and PCL injuries in adolescents and adults with achondroplasia, (2) compare this prevalence with that reported for the general population, (3) determine how many patients with ACL or PCL injuries underwent ligament reconstruction as treatment, and (4) determine patient activity levels as they relate to the rate of ACL/PCL injuries and reconstructions. We reviewed medical records of 430 patients with achondroplasia seen in the senior author's clinic from 2002 through 2014. Demographic data were reviewed, as well as any documentation of ACL or PCL injury or reconstruction. We called all 430 patients by telephone, and 148 agreed to participate in our survey, whereas 1 declined. We asked these patients about their history of ACL or PCL injury or reconstruction, as well as current and past physical activity levels. No ACL or PCL injuries were found on chart review. One patient reached by telephone reported an ACL injury that did not require reconstruction. This yielded a theoretical prevalence of 3/430 (0.7%). Of the 148 patients surveyed, 43 (29%) reported low physical activity, 75 (51%) reported moderate physical activity, and 26 (17%) reported high physical activity. There was no significant difference in the rate of ACL injury when stratified by physical activity level (P=0.102). ACL and PCL injuries and reconstructions are extremely rare in patients with achondroplasia, which cannot be completely ascribed to a low level of physical activity. One possible explanation is that patients with achondroplasia, on an average, have a more anterior tibial slope compared with those without achondroplasia, which decreases the force generated within the ACL and may protect against ACL injury. Further research is needed to explore possible causes. Level IV-retrospective review.

A novel nano-structured porous polycaprolactone scaffold improves hyaline cartilage repair in a rabbit model compared to a collagen type I/III scaffold: in vitro and in vivo studies.

PubMed

Christensen, Bjørn Borsøe; Foldager, Casper Bindzus; Hansen, Ole Møller; Kristiansen, Asger Albæk; Le, Dang Quang Svend; Nielsen, Agnete Desirée; Nygaard, Jens Vinge; Bünger, Cody Erik; Lind, Martin

2012-06-01

To develop a nano-structured porous polycaprolactone (NSP-PCL) scaffold and compare the articular cartilage repair potential with that of a commercially available collagen type I/III (Chondro-Gide) scaffold. By combining rapid prototyping and thermally induced phase separation, the NSP-PCL scaffold was produced for matrix-assisted autologous chondrocyte implantation. Lyophilizing a water-dioxane-PCL solution created micro and nano-pores. In vitro: The scaffolds were seeded with rabbit chondrocytes and cultured in hypoxia for 6 days. qRT-PCR was performed using primers for sox9, aggrecan, collagen type 1 and 2. In vivo: 15 New Zealand White Rabbits received bilateral osteochondral defects in the femoral intercondylar grooves. Autologous chondrocytes were harvested 4 weeks prior to surgery. There were 3 treatment groups: (1) NSP-PCL scaffold without cells. (2) The Chondro-Gide scaffold with autologous chondrocytes and (3) NSP-PCL scaffold with autologous chondrocytes. Observation period was 13 weeks. Histological evaluation was made using the O'Driscoll score. In vitro: The expressions of sox9 and aggrecan were higher in the NSP-PCL scaffold, while expression of collagen 1 was lower compared to the Chondro-Gide scaffold. In vivo: Both NSP-PCL scaffolds with and without cells scored significantly higher than the Chondro-Gide scaffold when looking at the structural integrity and the surface regularity of the repair tissue. No differences were found between the NSP-PCL scaffold with and without cells. The NSP-PCL scaffold demonstrated higher in vitro expression of chondrogenic markers and had higher in vivo histological scores compared to the Chondro-Gide scaffold. The improved chondrocytic differentiation can potentially produce more hyaline cartilage during clinical cartilage repair. It appears to be a suitable cell-free implant for hyaline cartilage repair and could provide a less costly and more effective treatment option than the Chondro-Gide scaffold with cells.

Preserving the PCL during the tibial cut in total knee arthroplasty.

PubMed

Cinotti, G; Sessa, P; Amato, M; Ripani, F R; Giannicola, G

2017-08-01

Previous studies have shown that the PCL insertion may be damaged during the tibial cut performed in total knee arthroplasty. We investigated the maximum thickness of a tibial cut that preserves the PCL insertion and to what extent the posterior slope of the tibial cut and that of the patient's tibial plateaus affect the outcome. MR images of 83 knees were analysed. The maximum thickness of a tibial cut that preserves the PCL using a posterior slope of 0°, 3°, 5° and parallel to the patient's slope of the tibial plateau, was evaluated. Correlations between the results and the degrees of the posterior slope of the patient's tibial plateaus were also investigated. The maximum thickness of a tibial cut that preserves the entire PCL insertion was, on average, 5.5, 4.7, 4.2 and 3.1 mm when a posterior slope of 0°, 3°, 5° and parallel to the patients' tibial plateaus was used, respectively. When the 25th percentile was considered, the maximum thickness of a tibial cut that preserved the PCL was 4 and 3 mm with a tibial cut of 0° and 5° of posterior slope, respectively. The maximum thickness of a tibial cut that preserved the PCL was significantly greater in patients with a sagittal slope of the tibial plateaus more than 8° than in those with a sagittal slope less than 8°. In cruciate retaining implants, the PCL insertion may be spared in the majority of patients by performing a tibial cut of 4 mm, or even less when a posterior slope of 3°-5° is used. The clinical relevance of our study is that the execution of a conservative tibial cut, followed by a second tibial resection to achieve the thickness required for the tibial component to be implanted, may be an alternative technique to spare the PCL in CR TKA. II.

Effects of different sterilization methods on the physico-chemical and bioresponsive properties of plasma-treated polycaprolactone films.

PubMed

Ghobeira, Rouba; Philips, Charlot; Declercq, Heidi; Cools, Pieter; De Geyter, Nathalie; Cornelissen, Ria; Morent, Rino

2017-01-24

For most tissue engineering applications, surface modification and sterilization of polymers are critical aspects determining the implant success. The first part of this study is thus dedicated to modifying polycaprolactone (PCL) surfaces via plasma treatment using a medium pressure dielectric barrier discharge, while the second part focuses on the sterilization of plasma-modified PCL. Chemical and physical surface changes are examined making use of water contact angle goniometry (WCA), x-ray photoelectron spectroscopy and atomic force microscopy. Bioresponsive properties are evaluated by performing cell culture tests. The results show that air and argon plasmas decrease the WCA significantly due to the incorporation of oxygen-containing functionalities onto the PCL surface, without modifying its morphology. Extended treatment times lead to PCL degradation, especially in the case of air plasma. In addition to surface modification, the plasma potential to sterilize PCL is studied with appropriate treatment times, but sterility has not been achieved so far. Therefore, plasma-modified films are subjected to UV, H 2 O 2 plasma (HP) and ethylene oxide (EtO) sterilizations. UV exposure of 3 h does not alter the PCL physico-chemical properties. A decreased wettability is observed after EtO sterilization, attributable to the modification of PCL chain ends reacting with EtO molecules. HP sterilization increases the WCA of the plasma-treated samples, presumably due to the scission of the hydrophilic bonds generated during the prior plasma treatments. Moreover, HP modifies the PCL surface morphology. For all the sterilizations, an improved cell adhesion and proliferation is observed on plasma-treated films compared to untreated ones. EtO shows the lowest proliferation rate compared to HP and UV. Overall, of the three sterilizations, UV is the most effective, since the physical alterations provoked by HP might interfere with the structural integrity when it comes to 3D scaffolds, and the chemical modifications caused by EtO, in addition to its toxicity, interfere with PCL bioactivity.

Micellar systems: Novel family for drug carriers

NASA Astrophysics Data System (ADS)

Rana, Meenakshi; Chowdhury, Papia

2016-05-01

Micellar systems have attracted a great deal of interest, especially in the field of biomedical sciences. The paper deals with the encapsulation behavior of Pyrrole-2-carboxyldehyde (PCL) an anti-cancer drug in different micellar systems. The inculsion capability of PCL is verified experimentally (UV-Vis, Photoluminescence and Raman spectroscopy) in polymer matrix. Two-micellar systems sodium dodecyl sulfate (SDS) and Polysorbate 80 (TWEEN 80) have been studied with a poorly water soluble PCL. The present work provides the effects of biocompatible organic PCL molecule entrap in micellar system in polymer phase due to its vast applicability in drug industry.

Self-assembly of tissue spheroids on polymeric membranes.

PubMed

Messina, Antonietta; Morelli, Sabrina; Forgacs, Gabor; Barbieri, Giuseppe; Drioli, Enrico; De Bartolo, Loredana

2017-07-01

In this study, multicellular tissue spheroids were fabricated on polymeric membranes in order to accelerate the fusion process and tissue formation. To this purpose, tissue spheroids composed of three different cell types, myoblasts, fibroblasts and neural cells, were formed and cultured on agarose and membranes of polycaprolactone (PCL) and chitosan (CHT). Membranes prepared by a phase-inversion technique display different physicochemical, mechanical and transport properties, which can affect the fusion process. The membranes accelerated the fusion process of a pair of spheroids with respect to the inert substrate. In this process, a critical role is played by the membrane properties, especially by their mechanical characteristics and oxygen and carbon dioxide mass transfer. The rate of fusion was quantified and found to be similar for fibroblast, myoblast and neural tissue spheroids on membranes, which completed the fusion within 3 days. These spheroids underwent faster fusion and maturation on PCL membrane than on agarose, the rate of fusion being proportional to the value of oxygen and carbon dioxide permeances and elastic characteristics. Consequently, tissue spheroids on the membranes expressed high biological activity in terms of oxygen uptake, making them more suitable as building blocks in the fabrication of tissues and organs. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

Attachment of nanoparticulate drug-release systems on poly(ε-caprolactone) nanofibers via a graftpolymer as interlayer.

PubMed

de Cassan, Dominik; Sydow, Steffen; Schmidt, Nadeschda; Behrens, Peter; Roger, Yvonne; Hoffmann, Andrea; Hoheisel, Anna Lena; Glasmacher, Birgit; Hänsch, Robert; Menzel, Henning

2018-03-01

Electrospun poly(ε-caprolactone) (PCL) fiber mats are modified using a chitosan grafted with PCL (CS-g-PCL), to improve the biological performance and to enable further modifications. The graft copolymer is immobilized by the crystallization of the PCL grafts on the PCL fiber surface as binding mechanism. In this way, the surface of the fibers is covered with chitosan bearing cationic amino groups, which allow adsorption of oppositely charged nanoparticulate drug-delivery systems. The modification of the fiber mats and the attachment of the drug delivery systems are easy and scalable dip processes. The process is also versatile; it is possible to attach different polymeric and inorganic nanoparticulate drug-release systems of cationic or anionic nature. The modifications are verified using scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM). As proof of principle, the release of ciprofloxacin from silica nanoparticles attached to the modified fiber mats is shown; however, the method is also suited for other biologically active substances including growth factors. The initial cellular attachment and proliferation as well as vitality of the cells is improved by the modification with CS-g-PCL and is further influenced by the type of the drug delivery system attached. Hence, this method can be used to transfer PCL fiber mats into bioactive implants for in-situ tissue engineering applications. Copyright © 2018 Elsevier B.V. All rights reserved.

Decomposition of P(CH 3) 3 on Ru(0001): comparison with PH 3 and PCl 3

NASA Astrophysics Data System (ADS)

Tao, H.-S.; Diebold, U.; Shinn, N. D.; Madey, T. E.

1997-04-01

The decomposition of P(CH 3) 3 adsorbed on Ru(0001) at 80 K is studied by soft X-ray photoelectron spectroscopy using synchrotron radiation. Using the chemical shifts in the P 2p core levels, we are able to identify various phosphorus-containing surface reaction products and follow their reactions on Ru(0001). It is found that P(CH 3) 3 undergoes a step-wise demethylation on Ru(0001), P(CH 3) 3 → P(CH 3) 2 → P(CH 3) → P, which is complete around ˜450 K. These results are compared with the decomposition of isostructural PH 3 and PCl 3 on Ru(0001). The decomposition of PH 3 involves a stable intermediate, labeled as PH x, and follows a reaction of: PH 3 → PH x → P, which is complete around ˜190 K. The conversion of chemisorbed phosphorus to ruthenium phosphide is observed and is complete around ˜700 K on Ru(0001). PCl 3 also follows a step-wise decomposition reaction, PCl 3 → PCl 2 → PCl → P, which is complete around ˜300 K. The energetics of the adsorption and the step-wise decomposition reactions of PH 3, PCl 3 and P(CH 3) 3 are estimated using the bond order conservation Morse potential (BOCMP) method. The energetics calculated using the BOCMP method agree qualitatively with the experimental data.

Examining the interrater reliability of the Hare Psychopathy Checklist-Revised across a large sample of trained raters.

PubMed

Blais, Julie; Forth, Adelle E; Hare, Robert D

2017-06-01

The goal of the current study was to assess the interrater reliability of the Psychopathy Checklist-Revised (PCL-R) among a large sample of trained raters (N = 280). All raters completed PCL-R training at some point between 1989 and 2012 and subsequently provided complete coding for the same 6 practice cases. Overall, 3 major conclusions can be drawn from the results: (a) reliability of individual PCL-R items largely fell below any appropriate standards while the estimates for Total PCL-R scores and factor scores were good (but not excellent); (b) the cases representing individuals with high psychopathy scores showed better reliability than did the cases of individuals in the moderate to low PCL-R score range; and (c) there was a high degree of variability among raters; however, rater specific differences had no consistent effect on scoring the PCL-R. Therefore, despite low reliability estimates for individual items, Total scores and factor scores can be reliably scored among trained raters. We temper these conclusions by noting that scoring standardized videotaped case studies does not allow the rater to interact directly with the offender. Real-world PCL-R assessments typically involve a face-to-face interview and much more extensive collateral information. We offer recommendations for new web-based training procedures. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Psychometric properties of the Hare Psychopathy Checklist-Revised (PCL-R) in a representative sample of Canadian federal offenders.

PubMed

Storey, Jennifer E; Hart, Stephen D; Cooke, David J; Michie, Christine

2016-04-01

The Hare Psychopathy Checklist-Revised (PCL-R; Hare, 2003) is a commonly used psychological test for assessing traits of psychopathic personality disorder. Despite the abundance of research using the PCL-R, the vast majority of research used samples of convenience rather than systematic methods to minimize sampling bias and maximize the generalizability of findings. This potentially complicates the interpretation of test scores and research findings, including the "norms" for offenders from the United States and Canada included in the PCL-R manual. In the current study, we evaluated the psychometric properties of PCL-R scores for all male offenders admitted to a regional reception center of the Correctional Service of Canada during a 1-year period (n = 375). Because offenders were admitted for assessment prior to institutional classification, they comprise a sample that was heterogeneous with respect to correctional risks and needs yet representative of all offenders in that region of the service. We examined the distribution of PCL-R scores, classical test theory indices of its structural reliability, the factor structure of test items, and the external correlates of test scores. The findings were highly consistent with those typically reported in previous studies. We interpret these results as indicating it is unlikely any sampling limitations of past research using the PCL-R resulted in findings that were, overall, strongly biased or unrepresentative. (c) 2016 APA, all rights reserved).

Zein Increases the Cytoaffinity and Biodegradability of Scaffolds 3D-Printed with Zein and Poly(ε-caprolactone) Composite Ink.

PubMed

Jing, Linzhi; Wang, Xiang; Liu, Hang; Lu, Yuyun; Bian, Jinsong; Sun, Jie; Huang, Dejian

2018-05-25

Electrohydrodynamic printing (EHDP) has attracted extensive interests as a powerful technology to fabricate micro- to nano-scale fibrous scaffolds in a custom-tailored manner for biomedical applications. A few synthetic biopolymer inks are applicable to this EHDP technology, but the fabricated scaffolds suffered from low mechanical strength, biocompatibility, and biodegradability. In this study, a series of poly(ε-caprolactone) (PCL)/zein composite inks were developed and their printability was examined on a solution-based EHDP system for scaffold fabrication. Multilayer grid scaffolds were manufactured by PCL, PCL/zein-10, and PCL/zein-20 inks, respectively and characterized. The mechanical strength of scaffolds printed by PCL/zein composite inks was remarkably enhanced in terms of Young's modulus and yield stress. The enzyme-accelerated in vitro degradation study demonstrated that zein-containing scaffolds exhibited dose-responsive improvement on the degradation rate as evidenced by surface morphological change of fibers. Moreover, the biocompatibility of PCL/zein scaffolds, tested on mice embryonic fibroblast (NIH/3T3) and human nonsmall lung cancer cell (H1299), manifested better cell affinity. Our findings suggest that scaffolds fabricated by the solution-based EHDP with PCL/zein composite inks can significantly improve Young's modulus, yield stress, biocompatibility, and biodegradability and have potential applications in drug delivery systems, 3D cell culture modeling, or tissue engineering.

Functionalization of PCL-3D Electrospun Nanofibrous Scaffolds for Improved BMP2-Induced Bone Formation.

PubMed

Miszuk, Jacob M; Xu, Tao; Yao, Qingqing; Fang, Fang; Childs, Josh D; Hong, Zhongkui; Tao, Jianning; Fong, Hao; Sun, Hongli

2018-03-01

Bone morphogenic protein 2 (BMP2) is a key growth factor for bone regeneration, possessing FDA approval for orthopedic applications. BMP2 is often required in supratherapeutic doses clinically, yielding adverse side effects and substantial treatment costs. Considering the crucial role of materials for BMPs delivery and cell osteogenic differentiation, we devote to engineering an innovative bone-matrix mimicking niche to improve low dose of BMP2-induced bone formation. Our previous work describes a novel technique, named thermally induced nanofiber self-agglomeration (TISA), for generating 3D electrospun nanofibrous (NF) polycaprolactone (PCL) scaffolds. TISA process could readily blend PCL with PLA, leading to increased osteogenic capabilities in vitro , however, these bio-inert synthetic polymers produced limited BMP2-induced bone formation in vivo. We therefore hypothesize that functionalization of NF 3D PCL scaffolds with bone-like hydroxyapatite (HA) and BMP2 signaling activator phenamil will provide a favorable osteogenic niche for bone formation at low doses of BMP2. Compared to PCL-3D scaffolds, PCL/HA-3D scaffolds demonstrated synergistically enhanced osteogenic differentiation capabilities of C2C12 cells with phenamil. Importantly, in vivo studies showed this synergism was able to generate significantly increased new bone in an ectopic mouse model, suggesting PCL/HA-3D scaffolds act as a favorable synthetic extracellular matrix for bone regeneration.

Evaluation of polycaprolactone matrices for the intravaginal delivery of metronidazole in the treatment of bacterial vaginosis.

PubMed

Pathak, Meenakshi; Turner, Mark; Palmer, Cheryn; Coombes, Allan G A

2014-09-01

Microporous, poly (ɛ-caprolactone) (PCL) matrices loaded with the antibacterial, metronidazole were produced by rapidly cooling suspensions of drug powder in PCL solutions in acetone. Drug incorporation in the matrices increased from 2.0% to 10.6% w/w on raising the drug loading of the PCL solution from 5% to 20% w/w measured with respect to the PCL content. Drug loading efficiencies of 40-53% were obtained. Rapid 'burst release' of 35-55% of the metronidazole content was recorded over 24 h when matrices were immersed in simulated vaginal fluid (SVF), due to the presence of large amounts of drug on matrix surface as revealed by Raman microscopy. Gradual release of around 80% of the drug content occurred over the following 12 days. Metronidazole released from PCL matrices in SVF retained antimicrobial activity against Gardnerella vaginalis in vitro at levels up to 97% compared to the free drug. Basic modelling predicted that the concentrations of metronidazole released into vaginal fluid in vivo from a PCL matrix in the form of an intravaginal ring would exceed the minimum inhibitory concentration of metronidazole against G. vaginalis. These findings recommend further investigation of PCL matrices as intravaginal devices for controlled delivery of metronidazole in the treatment and prevention of bacterial vaginosis. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Brownian dynamics simulation of amphiphilic block copolymers with different tail lengths, comparison with theory and comicelles.

PubMed

Hafezi, Mohammad-Javad; Sharif, Farhad

2015-11-01

Study on the effect of amphiphilic copolymers structure on their self assembly is an interesting subject, with important applications in the area of drug delivery and biological system treatments. Brownian dynamics simulations were performed to study self-assembly of the linear amphiphilic block copolymers with the same hydrophilic head, but hydrophobic tails of different lengths. Critical micelle concentration (CMC), gyration radius distribution, micelle size distribution, density profiles of micelles, shape anisotropy, and dynamics of micellization were investigated as a function of tail length. Simulation results were compared with predictions from theory and simulation for mixed systems of block copolymers with long and short hydrophobic tail, reported in our previous work. Interestingly, the equilibrium structural and dynamic parameters of pure and mixed block copolymers were similarly dependant on the intrinsic/apparent hydrophobic block length. Log (CMC) was, however; proportional to the tail length and had a different behavior compared to the mixed system. The power law scaling relation of equilibrium structural parameters for amphiphilic block copolymers predicts the same dependence for similar hydrophobic tail lengths, but the power law prediction of CMC is different, which is due to its simplifying assumptions as discussed here. Copyright © 2015 Elsevier Inc. All rights reserved.

Novel Principle of Contactless Gauge Block Calibration

PubMed Central

Buchta, Zdeněk; Řeřucha, Šimon; Mikel, Břetislav; Čížek, Martin; Lazar, Josef; Číp, Ondřej

2012-01-01

In this paper, a novel principle of contactless gauge block calibration is presented. The principle of contactless gauge block calibration combines low-coherence interferometry and laser interferometry. An experimental setup combines Dowell interferometer and Michelson interferometer to ensure a gauge block length determination with direct traceability to the primary length standard. By monitoring both gauge block sides with a digital camera gauge block 3D surface measurements are possible too. The principle presented is protected by the Czech national patent No. 302948. PMID:22737012

Novel principle of contactless gauge block calibration.

PubMed

Buchta, Zdeněk; Reřucha, Simon; Mikel, Břetislav; Cížek, Martin; Lazar, Josef; Cíp, Ondřej

2012-01-01

In this paper, a novel principle of contactless gauge block calibration is presented. The principle of contactless gauge block calibration combines low-coherence interferometry and laser interferometry. An experimental setup combines Dowell interferometer and Michelson interferometer to ensure a gauge block length determination with direct traceability to the primary length standard. By monitoring both gauge block sides with a digital camera gauge block 3D surface measurements are possible too. The principle presented is protected by the Czech national patent No. 302948.

Evaluation of long-term stability of low thermal expansion coefficient materials using gauge block interferometers

NASA Astrophysics Data System (ADS)

Hirai, Akiko; Bitou, Youichi; Oike, Yoshiyuki

2018-06-01

The long-term stability of NEXCERA™ ceramics having a low coefficient of thermal expansion was evaluated over a period of eight years. Several gauge blocks of differing lengths were prepared, using two types of NEXCERA. Each gauge block was kept wrung to a platen and its absolute length was periodically measured by gauge block interferometer during the eight years. Relative uncertainties of measurement of changes in gauge block length were estimated as 4.1  ×  10‑8 and 2.9  ×  10‑8 for 200 mm and 800 mm gauge blocks, respectively. The experimental results show the trend of expansion and a relative change of less than 0.1  ×  10‑6/year for every gauge block.

Fabrication of polycaprolactone-silanated β-tricalcium phosphate-heparan sulfate scaffolds for spinal fusion applications.

PubMed

Bhakta, Gajadhar; Ekaputra, Andrew K; Rai, Bina; Abbah, Sunny A; Tan, Tuan Chun; Le, Bach Quang; Chatterjea, Anindita; Hu, Tao; Lin, Tingxuan; Arafat, M Tarik; van Wijnen, Andre J; Goh, James; Nurcombe, Victor; Bhakoo, Kishore; Birch, William; Xu, Li; Gibson, Ian; Wong, Hee-Kit; Cool, Simon M

2018-05-01

Interbody spinal fusion relies on the use of external fixation and the placement of a fusion cage filled with graft materials (scaffolds) without regard for their mechanical performance. Stability at the fusion site is instead reliant on fixation hardware combined with a selected cage. Ideally, scaffolds placed into the cage should both support the formation of new bone and contribute to the mechanical stability at the fusion site. We recently developed a scaffold consisting of silane-modified PCL-TCP (PCL-siTCP) with mechanical properties that can withstand the higher loads generated in the spine. To ensure the scaffold more closely mimicked the bone matrix, we incorporated collagen (Col) and a heparan sulfate glycosaminoglycan sugar (HS3) with increased affinity for heparin-binding proteins such as bone morphogenetic protein-2 (BMP-2). The osteostimulatory characteristic of this novel device delivering exogenous BMP2 was assessed in vitro and in vivo as a prelude to future spinal fusion studies with this device. A combination of cell-free assays (BMP2 release), progenitor cell-based assays (BMP2 bioactivity, cell proliferation and differentiation), and rodent ectopic bone formation assays was used to assess the osteostimulatory characteristics of the PCL-siTCP-based scaffolds. Freshly prepared rat mesenchymal stem cells were used to determine reparative cell proliferation and differentiation on the PCL-siTCP-based scaffolds over a 28-day period in vitro. The bioactivity of BMP2 released from the scaffolds was assessed on progenitor cells over a 28-day period using ALP activity assays and release kinetics as determined by enzyme-linked immunosorbent assay. For ectopic bone formation, intramuscular placement of scaffolds into Sprague Dawley rats (female, 4 weeks old, 120-150 g) was achieved in five animals, each receiving four treatments randomized for location along the limb. The four groups tested were (1) PCL-siTCP/Col (5-mm diameter×1-mm thickness), PCL-siTCP/Col/BMP2 (5 µg), (3) PCL-siTCP/Col/HS3 (25 µg), and (4) PCL-siTCP/Col/HS3/BMP2 (25 and 5 µg, respectively). Bone formation was evaluated at 8 weeks post implantation by microcomputed tomography (µCT) and histology. Progenitor cell-based assays (proliferation, mRNA transcripts, and ALP activity) confirmed that BMP2 released from PCL-siTCP/Col/HS3 scaffolds increased ALP expression and mRNA levels of the osteogenic biomarkers Runx2, Col1a2, ALP, and bone gla protein-osteocalcin compared with devices without HS3. When the PCL-siTCP/Col/HS3/BMP2 scaffolds were implanted into rat hamstring muscle, increased bone formation (as determined by two-dimensional and three-dimensional µCTs and histologic analyses) was observed compared with scaffolds lacking BMP2. More consistent increases in the amount of ectopic bone were observed for the PCL-siTCP/Col/HS3/BMP2 implants compared with PCL-siTCP/Col/BMP2. Also, increased mineralizing tissue within the pores of the scaffold was seen with modified-tetrachrome histology, a result confirmed by µCT, and a modest but detectable increase in both the number and the thickness of ectopic bone structures were observed with the PCL-siTCP/Col/HS3/BMP2 implants. The combination of PCL-siTCP/Col/HS3/BMP2 thus represents a promising avenue for further development as a bone graft alternative for spinal fusion surgery. Copyright © 2017 Elsevier Inc. All rights reserved.

Biomechanical Comparison of Five Posterior Cruciate Ligament Reconstruction Techniques.

PubMed

Nuelle, Clayton W; Milles, Jeffrey L; Pfeiffer, Ferris M; Stannard, James P; Smith, Patrick A; Kfuri, Mauricio; Cook, James L

2017-07-01

No surgical technique recreates native posterior cruciate ligament (PCL) biomechanics. We compared the biomechanics of five different PCL reconstruction techniques versus the native PCL. Cadaveric knees ( n  = 20) were randomly assigned to one of five reconstruction techniques: Single bundle all-inside arthroscopic inlay, single bundle all-inside suspensory fixation, single bundle arthroscopic-assisted open onlay (SB-ONL), double bundle arthroscopic-assisted open inlay (DB-INL), and double bundle all-inside suspensory fixation (DB-SUSP). Each specimen was potted and connected to a servo-hydraulic load frame for testing in three conditions: PCL intact, PCL deficient, and PCL reconstructed. Testing consisted of a posterior force up to 100 N at a rate of 1 N/s at four knee flexion angles: 10, 30, 60, and 90 degrees. Three material properties were measured under each condition: load to 5 mm displacement, maximal displacement, and stiffness. Data were normalized to the native PCL, compared across techniques, compared with all PCL-intact knees and to all PCL-deficient knees using one-way analysis of variance. For load to 5 mm displacement, intact knees required significantly ( p  < 0.03) more load at 30 degrees of flexion than all reconstructions except the DB-SUSP. At 60 degrees of flexion, intact required significantly ( p  < 0.01) more load than all others except the SB-ONL. At 90 degrees, intact, SB-ONL, DB-INL, and DB-SUSP required significantly more load ( p  < 0.05). Maximal displacement testing showed the intact to have significantly ( p  < 0.02) less laxity than all others except the DB-INL and DB-SUSP at 60 degrees. At 90 degrees the intact showed significantly ( p  < 0.01) less laxity than all others except the DB-SUSP. The intact was significantly stiffer than all others at 30 degrees ( p  < 0.03) and 60 degrees ( p  < 0.01). Finally, the intact was significantly ( p  < 0.05) stiffer than all others except the DB-SUSP at 90 degrees. No technique matched the exact properties of the native PCL, but the double bundle reconstructions more closely recreated the native biomechanics immediately after implantation, with the DB-SUSP coming closest to the native ligament. This study contributes new data for consideration in PCL reconstruction technique choice. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

The prevalence of post-traumatic stress disorder (PTSD) in US combat soldiers: a head-to-head comparison of DSM-5 versus DSM-IV-TR symptom criteria with the PTSD checklist.

PubMed

Hoge, Charles W; Riviere, Lyndon A; Wilk, Joshua E; Herrell, Richard K; Weathers, Frank W

2014-09-01

The definition of post-traumatic stress disorder (PTSD) underwent substantial changes in the 2013 edition of the Diagnostic and Statistical Manual of Mental Disorders (DSM-5). How this will affect estimates of prevalence, whether clinical utility has been improved, and how many individuals who meet symptom criteria according to the previous definition will not meet new criteria is unknown. Updated screening instruments, including the PTSD checklist (PCL), have not been compared with previously validated methods through head-to-head comparisons. We compared the new 20-item PCL, mapped to DSM-5 (PCL-5), with the original validated 17-item specific stressor version (PCL-S) in 1822 US infantry soldiers, including 946 soldiers who had been deployed to Iraq or Afghanistan. Surveys were administered in November, 2013. Soldiers alternately received either of two surveys that were identical except for the order of the two PCL versions (911 per group). Standardised scales measured major depression, generalised anxiety, alcohol misuse, and functional impairment. In analysis of all soldiers, 224 (13%) screened positive for PTSD by DSM-IV-TR criteria and 216 (12%) screened positive by DSM-5 criteria (κ 0·67). In soldiers exposed to combat, 177 (19%) screened positive by DSM-IV-TR and 165 (18%) screened positive by DSM-5 criteria (0·66). However, of 221 soldiers with complete data who met DSM-IV-TR criteria, 67 (30%) did not meet DSM-5 criteria, and 59 additional soldiers met only DSM-5 criteria. PCL-5 scores from 15-38 performed similarly to PCL-S scores of 30-50; a PCL-5 score of 38 gave optimum agreement with a PCL-S of 50. The two definitions showed nearly identical association with other psychiatric disorders and functional impairment. Our findings showed the PCL-5 to be equivalent to the validated PCL-S. However, the new PTSD symptom criteria do not seem to have greater clinical utility, and a high percentage of soldiers who met criteria by one definition did not meet the other criteria. Clinicians need to consider how to manage discordant outcomes, particularly for service members and veterans with PTSD who no longer meet criteria under DSM-5. US Army Military Operational Medicine Research Program (MOMRP), Fort Detrick, MD. Copyright © 2014 Elsevier Ltd. All rights reserved.

A smart core-sheath nanofiber that captures and releases red blood cells from the blood

NASA Astrophysics Data System (ADS)

Shi, Q.; Hou, J.; Zhao, C.; Xin, Z.; Jin, J.; Li, C.; Wong, S.-C.; Yin, J.

2016-01-01

A smart core-sheath nanofiber for non-adherent cell capture and release is demonstrated. The nanofibers are fabricated by single-spinneret electrospinning of poly(N-isopropylacrylamide) (PNIPAAm), polycaprolactone (PCL) and nattokinase (NK) solution blends. The self-assembly of PNIPAAm and PCL blends during the electrospinning generates the core-sheath PCL/PNIPAAm nanofibers with PNIPAAm as the sheath. The PNIPAAm-based core-sheath nanofibers are switchable between hydrophobicity and hydrophilicity with temperature change and enhance stability in the blood. When the nanofibers come in contact with blood, the NK is released from the nanofibers to resist platelet adhesion on the nanofiber surface, facilitating the direct capture and isolation of red blood cells (RBCs) from the blood above phase-transition temperature of PNIPAAm. Meanwhile, the captured RBCs are readily released from the nanofibers with temperature stimuli in an undamaged manner. The release efficiency of up to 100% is obtained while maintaining cellular integrity and function. This work presents promising nanofibers to effectively capture non-adherent cells and release for subsequent molecular analysis and diagnosis of single cells.A smart core-sheath nanofiber for non-adherent cell capture and release is demonstrated. The nanofibers are fabricated by single-spinneret electrospinning of poly(N-isopropylacrylamide) (PNIPAAm), polycaprolactone (PCL) and nattokinase (NK) solution blends. The self-assembly of PNIPAAm and PCL blends during the electrospinning generates the core-sheath PCL/PNIPAAm nanofibers with PNIPAAm as the sheath. The PNIPAAm-based core-sheath nanofibers are switchable between hydrophobicity and hydrophilicity with temperature change and enhance stability in the blood. When the nanofibers come in contact with blood, the NK is released from the nanofibers to resist platelet adhesion on the nanofiber surface, facilitating the direct capture and isolation of red blood cells (RBCs) from the blood above phase-transition temperature of PNIPAAm. Meanwhile, the captured RBCs are readily released from the nanofibers with temperature stimuli in an undamaged manner. The release efficiency of up to 100% is obtained while maintaining cellular integrity and function. This work presents promising nanofibers to effectively capture non-adherent cells and release for subsequent molecular analysis and diagnosis of single cells. Electronic supplementary information (ESI) available: Electrospinning of polymer nanofibers; FTIR spectra and XPS spectra of PCL, PNIPAAm and PCL/PNIPAAm nanofibers; SEM images of PCL/PNIPAAm nanofibers with varied composition; PNIPAAm content on the sheath of nanofibers; stability of core-sheath PCL/PNIPAAm nanofibers. Platelet adhesion on the PCL/PNIPAAm nanofibers in the presence of NK; Protein adsorption on nanofibers. See DOI: 10.1039/c5nr07070h

Clinical outcomes for teeth treated with electrospun poly(ε-caprolactone) fiber meshes/mineral trioxide aggregate direct pulp capping.

PubMed

Lee, Li-Wan; Hsiao, Sheng-Huang; Hung, Wei-Chiang; Lin, Yun-Ho; Chen, Po-Yu; Chiang, Chun-Pin

2015-05-01

Mineral trioxide aggregate (MTA) is a biocompatible material for direct pulp capping. This study was designed to compare the clinical outcomes of pulp-exposed teeth treated with either poly(ε-caprolactone) fiber mesh (PCL-FM) as a barrier for MTA (so-called PCL-FM/MTA) or MTA direct pulp capping. Sixty human vital teeth were evenly divided into 4 groups (n = 15 in each group). Teeth in groups 1 and 3 had pulp exposure <1 mm in diameter, whereas teeth in groups 2 and 4 had pulp exposure of 1-1.5 mm in diameter. Teeth in groups 1 and 2 were treated with PCL-FM/MTA direct pulp capping, and those in groups 3 and 4 were treated with MTA direct pulp capping. Teeth treated with PCL-FM/MTA direct pulp capping needed a significantly shorter mean duration for dentin bridge formation than teeth treated with MTA direct pulp capping. Moreover, teeth with pulp exposure <1.0 mm in diameter needed a significantly shorter mean duration for dentin bridge formation than teeth with pulp exposure of 1-1.5 mm in diameter after either PCL-FM/MTA or MTA direct pulp capping treatment. In addition, teeth treated with PCL-FM/MTA direct pulp capping formed an approximately 3-fold thicker dentin bridge than teeth treated with MTA direct pulp capping 8 weeks or 3 months later. Furthermore, none of the teeth treated with PCL-FM/MTA direct pulp capping showed tooth discoloration after treatment for 3 months. PCL-FM/MTA is a better combination material than MTA alone for direct pulp capping of human permanent teeth. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Psychometric analysis of the PTSD Checklist-5 (PCL-5) among treatment-seeking military service members.

PubMed

Wortmann, Jennifer H; Jordan, Alexander H; Weathers, Frank W; Resick, Patricia A; Dondanville, Katherine A; Hall-Clark, Brittany; Foa, Edna B; Young-McCaughan, Stacey; Yarvis, Jeffrey S; Hembree, Elizabeth A; Mintz, Jim; Peterson, Alan L; Litz, Brett T

2016-11-01

The Posttraumatic Stress Disorder Checklist (PCL-5; Weathers et al., 2013) was recently revised to reflect the changed diagnostic criteria for posttraumatic stress disorder (PTSD) in the fifth edition of the Diagnostic and Statistical Manual of Mental Disorders (DSM-5; American Psychiatric Association, 2013). We investigated the psychometric properties of PCL-5 scores in a large cohort (N = 912) of military service members seeking PTSD treatment while stationed in garrison. We examined the internal consistency, convergent and discriminant validity, and DSM-5 factor structure of PCL-5 scores, their sensitivity to clinical change relative to PTSD Symptom Scale-Interview (PSS-I; Foa, Riggs, Dancu, & Rothbaum, 1993) scores, and their diagnostic utility for predicting a PTSD diagnosis based on various measures and scoring rules. PCL-5 scores exhibited high internal consistency. There was strong agreement between the order of hypothesized and observed correlations among PCL-5 and criterion measure scores. The best-fitting structural model was a 7-factor hybrid model (Armour et al., 2015), which demonstrated closer fit than all other models evaluated, including the DSM-5 model. The PCL-5's sensitivity to clinical change, pre- to posttreatment, was comparable with that of the PSS-I. Optimally efficient cut scores for predicting PTSD diagnosis were consistent with prior research with service members (Hoge, Riviere, Wilk, Herrell, & Weathers, 2014). The results indicate that the PCL-5 is a psychometrically sound measure of DSM-5 PTSD symptoms that is useful for identifying provisional PTSD diagnostic status, quantifying PTSD symptom severity, and detecting clinical change over time in PTSD symptoms among service members seeking treatment. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Three-dimensional electrospun polycaprolactone (PCL)/alginate hybrid composite scaffolds.

PubMed

Kim, Min Seong; Kim, GeunHyung

2014-12-19

Micro/nanofibrous scaffolds have been used widely in biomedical applications because the micro/nano-scale fibres resemble natural extracellular matrix and the high surface-to-volume ratio encourages cellular activities (attachment and proliferation). However, poor mechanical properties, low controllability of various shapes and difficulties in obtaining controllable pore structure have been obstacles to their use in hard-tissue regeneration. To overcome these shortcomings, we suggest a new composite system, which uses a combination method of wet electrospinning, rapid prototyping and a physical punching process. Using the process, we obtained polycaprolactone (PCL)/alginate composite scaffolds, consisting of electrospun PCL/alginate fibres and micro-sized PCL struts, with mean pore sizes of 821 ± 55 μm. To show the feasibility of the scaffolds for hard-tissue regeneration, the scaffolds were assessed not only for physical properties, including hydrophilicity, water absorption, and tensile and compressive strength, but also in vitro cellular responses (cell viability and proliferation) and osteogenic differentiation (alkaline phosphatase (ALP) activity, and mineralisation) by culturing with pre-osteoblasts (MC3T3-E1 cells). With the reinforcing micro-sized PCL struts, the elastic modulus of the PCL/alginate scaffold was significantly improved versus a pure PCL scaffold. Additionally, due to the alginate component in the fibrous scaffold, they showed significantly enhanced hydrophilic behaviour, water absorption (∼8-fold) and significant biological activities (∼1.6-fold for cell viability at 7 days, ∼2.3-fold for ALP activity at 14 days and ∼6.4-fold for calcium mineralisation at 14 days) compared with those of a pure PCL fibrous scaffold. Copyright © 2014 Elsevier Ltd. All rights reserved.

Micromatricial metronidazole benzoate film as a local mucoadhesive delivery system for treatment of periodontal diseases.

PubMed

El-Kamel, Amal Hassan; Ashri, Lubna Y; Alsarra, Ibrahim A

2007-09-14

The main objective of this study was to develop a local, oral mucoadhesive metronidazole benzoate (MET) delivery system that can be applied and removed by the patient for the treatment of periodontal diseases. Mucoadhesive micromatricial chitosan/poly(epsilon-caprolactone) (CH/PCL) films and chitosan films were prepared. Thermal behavior, morphology, and particle size measurements were used to evaluate the prepared films. The effect of different molar masses of CH and different ratios of medium Mwt molar mass chitosan (MCH):PCL on water absorption, in vitro bioadhesion, mechanical properties, and in vitro drug release was examined. In vivo performance of the selected formulation was also evaluated. Differential scanning calorimetry examination revealed that MET existed mainly in amorphous form. Under microscopic examination, PCL microparticles were homogeneously dispersed in the films. The use of different molar masses of CH and different ratios of (MCH):PCL affected the size of the entrapped particles. Addition of PCL significantly decreased percentage water uptake and bioadhesion force compared with pure CH film. With regard to mechanical properties, the 2-layered film containing 1:0.625 MCH:PCL had the best tensile properties. At fixed CH:PCL ratio (1:1.25), the slowest drug release was obtained from films containing high molar mass CH. On the other hand, the 2-layered film that consisted of 1:0.625 MCH:PCL had the slowest MET release. In vivo evaluation of the selected film revealed that metronidazole concentration in saliva over 6 hours ranged from 5 to 15 microg/mL, which was within and higher than the reported range of minimum inhibitory concentration for metronidazole. A significant in vitro/in vivo correlation under the adopted experimental conditions was obtained.

The role and reliability of the Psychopathy Checklist-Revised in U.S. sexually violent predator evaluations: a case law survey.

PubMed

DeMatteo, David; Edens, John F; Galloway, Meghann; Cox, Jennifer; Smith, Shannon Toney; Formon, Dana

2014-06-01

The civil commitment of offenders as sexually violent predators (SVPs) is a highly contentious area of U.S. mental health law. The Psychopathy Checklist-Revised (PCL-R) is frequently used in mental health evaluations in these cases to aid legal decision making. Although generally perceived to be a useful assessment tool in applied settings, recent research has raised questions about the reliability of PCL-R scores in SVP cases. In this report, we review the use of the PCL-R in SVP trials identified as part of a larger project investigating its role in U.S. case law. After presenting data on how the PCL-R is used in SVP cases, we examine the reliability of scores reported in these cases. We located 214 cases involving the PCL-R, 88 of which included an actual score and 29 of which included multiple scores. In the 29 cases with multiple scores, the intraclass correlation coefficient for a single evaluator for the PCL-R scores was only .58, and only 41.4% of the difference scores were within 1 standard error of measurement unit. The average score reported by prosecution experts was significantly higher than the average score reported by defense-retained experts, and prosecution experts reported PCL-R scores of 30 or above in nearly 50% of the cases, compared with less than 10% of the cases for defense witnesses (κ = .29). In conjunction with other recently published findings demonstrating the unreliability of PCL-R scores in applied settings, our results raise questions as to whether this instrument should be admitted into SVP proceedings.

Antitumor activity of monomethoxy poly(ethylene glycol)-poly (ε-caprolactone) micelle-encapsulated doxorubicin against mouse melanoma.

PubMed

Zheng, Lan; Gou, Maling; Zhou, Shengtao; Yi, Tao; Zhong, Qian; Li, Zhengyu; He, Xiang; Chen, Xiancheng; Zhou, Lina; Wei, Yuquan; Qian, Zhiyong; Zhao, Xia

2011-06-01

Doxorubicin (Dox) is one of the most commonly used and highly effective antineoplastic agents, but the clinical application of this broad spectrum drug is largely hampered by its poor stability and serious toxicity to normal tissues. Hence, it is essential to improve the therapeutic effect and decrease the systematic toxicity for the administration of doxorubicin. In our study, doxorubicin was incorporated into monomethoxy poly(ethylene glycol)-poly(ε-caprolactone) (MPEG-PCL) micelle by a self-assembly method. The cytotoxicity and cellular uptake efficiency of Dox-loaded MPEG-PCL (Dox/MPEG-PCL) micelle against B16-F10 murine melanoma cells was examined by the methylthiazoltetrazolium (MTT) test and flow cytometry. The antitumor activity of Dox/MPEG-PCL was evaluated in C57BL/6 mice injected subcutaneously with B16-F10 cells. Toxicity was evaluated in tumor-free mice. Meanwhile, tumor proliferation, intratumoal angiogenesis and apoptotic cells were evaluated by PCNA, CD31 staining and TUNEL assay, respectively. Encapsulation of doxorubicin in MPEG-PCL micelle improved the cytotoxicity of doxorubicin and enhanced its cellular uptake on B16-F10 cell in vitro. Administration of Dox/MPEG-PCL micelle resulted in significant inhibition (75% maximum inhibition relative to controls) in the growth of B16-F10 tumor xenografts and prolonged the survival of the treated mice (P<0.05). These anti-tumor responses were associated with marked increase of tumor apoptosis and notable reduction of cell proliferation and intratumoral microvessel density (P<0.05). The system toxicity also decreased in the Dox/MPEG-PCL group compared with free doxorubicin group. Our data indicate that the encapsulation of doxorubicin in MPEG-PCL micelle improved the anti-tumor activity in vivo without conspicuous systemic toxic effects.

Biodegradable electrospun nanofibers coated with platelet-rich plasma for cell adhesion and proliferation

PubMed Central

Díaz-Gómez, Luis; Alvarez-Lorenzo, Carmen; Concheiro, Angel; Silva, Maite; Dominguez, Fernando; Sheikh, Faheem A.; Cantu, Travis; Desai, Raj; Garcia, Vanessa L.; Macossay, Javier

2014-01-01

Biodegradable electrospun poly(ε-caprolactone) (PCL) scaffolds were coated with platelet-rich plasma (PRP) to improve cell adhesion and proliferation. PRP was obtained from human buffy coat, and tested on human adipose-derived mesenchymal stem cells (MSC) to confirm cell proliferation and cytocompatibility. Then, PRP was adsorbed on the PCL scaffolds via lyophilization, which resulted in uniform sponge-like coating of 2.85 (s.d. 0.14) mg/mg. The scaffolds were evaluated regarding mechanical properties (Young’s modulus, tensile stress and tensile strain), sustained release of total protein and growth factors (PDGF-BB, TGF-β1 and VEGF), and hemocompatibility. MSC seeded on the PRP-PCL nanofibers showed an increased adhesion and proliferation compared to pristine PCL fibers. Moreover, the adsorbed PRP enabled angiogenesis features observed as neovascularization in a chicken chorioallantoic membrane (CAM) model. Overall, these results suggest that PRP-PCL scaffolds hold promise for tissue regeneration applications. PMID:24857481

Co-electrospun poly(ɛ-caprolactone)/cellulose nanofibers-fabrication and characterization.

PubMed

Ahmed, Farooq; Saleemi, Sidra; Khatri, Zeeshan; Abro, Muhammad Ishaque; Kim, Ick-Soo

2015-01-22

We report fabrication of poly (ɛ-caprolactone) (PCL)/cellulose (CEL) nanofiber blends via co-electrospinning for the possible use as biofilters and biosensor strips. Five different ratios of PCL to CEL were fabricated to investigate the wicking behavior. The cellulose acetate (CA) was taken as precursor to make cellulose nanofibers. Double nozzles were employed for jetting constituent polymers toward collector drum independently and resultant nanofibers webs were deacetylated in aqueous alkaline solution to convert CA into CEL as confirmed by FTIR spectra. FTIR further revealed that there is no effect of deacetylation on PCL nanofiber. The morphology of each blend webs under SEM showed uniform and bead-free nanofibers. Wicking behavior for five different ratios of PCL/CEL suggested that increasing CEL ratio in the blend enhanced the wicking front height; however, X-ray diffraction patterns of PCL/CEL showed a slight decrease in crystallinity. Copyright © 2014 Elsevier Ltd. All rights reserved.

Psychometric properties of seven self-report measures of posttraumatic stress disorder in college students with mixed civilian trauma exposure.

PubMed

Adkins, Jennifer W; Weathers, Frank W; McDevitt-Murphy, Meghan; Daniels, Jennifer B

2008-12-01

In this study psychometric properties of seven self-report measures of posttraumatic stress disorder (PTSD) were compared. The seven scales evaluated were the Davidson Trauma Scale (DTS), the PTSD Checklist (PCL), the Posttraumatic Stress Diagnostic Scale (PDS), the Civilian Mississippi Scale (CMS), the Impact of Event Scale-Revised (IES-R), the Penn Inventory for Posttraumatic Stress Disorder (Penn), and the PK scale of the MMPI-2 (PK). Participants were 239 (79 male and 160 female) trauma-exposed undergraduates. All seven measures exhibited good test-retest reliability and internal consistency. The PDS, PCL and DTS demonstrated the best convergent validity; the IES-R, PDS, and PCL demonstrated the best discriminant validity; and the PDS, PCL, and IES-R demonstrated the best diagnostic utility. Overall, results most strongly support the use of the PDS and the PCL for the assessment of PTSD in this population.

Gradient-index phononic crystal lens-based enhancement of elastic wave energy harvesting

NASA Astrophysics Data System (ADS)

Tol, S.; Degertekin, F. L.; Erturk, A.

2016-08-01

We explore the enhancement of structure-borne elastic wave energy harvesting, both numerically and experimentally, by exploiting a Gradient-Index Phononic Crystal Lens (GRIN-PCL) structure. The proposed GRIN-PCL is formed by an array of blind holes with different diameters on an aluminum plate, where the blind hole distribution is tailored to obtain a hyperbolic secant gradient profile of refractive index guided by finite-element simulations of the lowest asymmetric mode Lamb wave band diagrams. Under plane wave excitation from a line source, experimentally measured wave field validates the numerical simulation of wave focusing within the GRIN-PCL domain. A piezoelectric energy harvester disk located at the first focus of the GRIN-PCL yields an order of magnitude larger power output as compared to the baseline case of energy harvesting without the GRIN-PCL on the uniform plate counterpart.

Open Tibial Inlay PCL Reconstruction: Surgical Technique and Clinical Outcomes.

PubMed

Vellios, Evan E; Jones, Kristofer J; McAllister, David R

2018-06-01

To review the current literature on clinical outcomes following open tibial inlay posterior cruciate ligament (PCL) reconstruction and provide the reader with a detailed description of the author's preferred surgical technique. Despite earlier biomechanical studies which demonstrated superiority of the PCL inlay technique when compared to transtibial techniques, recent longitudinal cohort studies have shown no significant differences in clinical or functional outcomes at 10-year follow-up. Furthermore, no significant clinical differences have been shown between graft types used and/or single- versus double-bundle reconstruction methods. The optimal treatment for the PCL-deficient knee remains unclear. Open tibial inlay PCL reconstruction is safe, reproducible, and avoids the "killer turn" that may potentially lead to graft weakening and failure seen in transtibial reconstruction methods. No significant differences in subjective outcomes or clinical laxity have been shown between single-bundle versus double-bundle reconstruction methods.

"Transversus Abdominis Plane Blocks in Microsurgical Breast Reconstruction: Analysis of Pain, Narcotic Consumption, Length of Stay and Cost."

PubMed

Salibian, Ara A; Frey, Jordan D; Thanik, Vishal D; Karp, Nolan S; Choi, Mihye

2018-06-02

Transversus abdominis plane (TAP) blocks are increasingly being utilized in microvascular breast reconstruction. The implications of TAP blocks on specific reconstructive, patient and institutional outcomes remain to be fully elucidated. Patients undergoing abdominally-based microvascular breast reconstruction from 2015-2017 were reviewed. Length of stay, complications, narcotic consumption, donor-site pain and hospital expenses were compared between patients that did and those that did not receive TAP blocks with liposomal bupivacaine. Outcomes were subsequently compared in patients with elevated body mass index (BMI). Fifty patients (43.9%) received TAP blocks (27 [54.0%] under ultrasound guidance) and 64 patients (56.1%) did not. Patients with TAP blocks had significantly decreased oral and total narcotic consumption (p=0.0001 and p<0.0001, respectively) as well as significantly less donor-site pain (3.3 versus 4.3, p<0.0001). There was no significant difference in hospital expenses between the two cohorts ($21,531.53 versus $22,050.15 per patient, p=0.5659). Patients with BMI≥25 who received TAP blocks had a significantly decreased length of stay (3.8 versus 4.4 days, p=0.0345) as well as decreased narcotic consumption and postoperative pain compared to patients without TAP blocks. Patients with BMI<25 did not have a significant difference in postoperative pain, narcotic consumption or length of stay between the TAP versus no TAP block groups. TAP blocks with liposomal bupivacaine significantly reduce oral and total postoperative narcotic consumption as well as donor-site pain in all patients after abdominally-based microvascular breast reconstruction without increasing hospital expenses. TAP blocks additionally significantly decrease length of stay in patients with BMI≥25.

A Taxometric Analysis of the Psychopathy Checklist: Screening Version (PCL:SV): Further Evidence of Dimensionality

ERIC Educational Resources Information Center

Walters, Glenn D.; Gray, Nicola S.; Jackson, Rebecca L.; Sewell, Kenneth W.; Rogers, Richard; Taylor, John; Snowden, Robert J.

2007-01-01

A taxometric analysis of the Psychopathy Checklist: Screening Version (PCL:SV; S. D. Hart, D. N. Cox, & R. D. Hare, 1995) was performed on a group of 2,250 male and female forensic/psychiatric patients and jail/prison inmates. The 4 PCL:SV facet scores (Interpersonal, Affective, Impulsive Lifestyle, Antisocial Behavior) served as indicators in…

Using MMPI-2-RF Correlates to Elucidate the PCL-R and Its Four Facets in a Sample of Male Forensic Psychiatric Patients.

PubMed

Klein Haneveld, Evelyn; Kamphuis, Jan H; Smid, Wineke; Forbey, Johnathan D

2017-01-01

This study documents the associations between the MMPI-2-RF (Ben-Porath & Tellegen, 2008 ) scale scores and the Psychopathy Checklist Revised (PCL-R; Hare, 2003 ) facet scores in a forensic psychiatric sample. Objectives were to determine how the MMPI-2-RF scales might enhance substantive understanding of the nature of the 4 PCL-R facets and to discern possible implications for the treatment of psychopathic patients. A sample of 127 male forensic psychiatric offenders admitted to a Dutch forensic psychiatric hospital completed the PCL-R and the MMPI-2. Exploratory stepwise regression analyses assessed the prediction of the PCL-R total and its facet scores from MMPI-2-RF scales at its 3 hierarchical levels. Conceptually meaningful results emerged at each level of the MMPI-2-RF hierarchy, including several consistent differences between predictor sets across the facets. Interestingly, ideas of persecution (RC6) was a specific predictor of PCL-R Facet 2, a facet noted for its association with treatment failure. Results are compared and contrasted to the extant body of empirical work to date, and some tentative clinical implications are offered.

Percutaneous cavitary lavage in the diagnosis of pulmonary cavities

PubMed Central

Findik, Serhat; Ozmen, Zafer; Atici, Atilla Guven; Akan, Huseyin

2013-01-01

Objective To investigate diagnostic significance of percutaneous cavitary lavage (PCL) in differential diagnosis of benign and malignant pulmonary cavitary lesions. Methods An alternative diagnostic method called PCL was performed on 16 patients having peripherally located pulmonary cavitary lesions with thin walls which were not suitable for tissue biopsy and whose diagnosis could not be made by sputum examination and bronchoscopic procedures. A 22-gauge needle was inserted into the cavity under computed tomography (CT) guidance. Saline was injected through the needle and then aspirated. The specimen was examined cytologically and microbiologically. Results PCL could make a correct diagnosis in 12 of 16 patients (75%). In three patients (18.7%) appropriate specimen could not be taken. Diagnostic sensitivity and specificity of PCL for malignant-benign differentiation was 80% and 100%, respectively. The accuracy of PCL for this differentiation was 92.3%. There was only one complication, a small pneumothorax resolved without any intervention. Conclusions PCL is an alternative method in the differential diagnosis of thin walled pulmonary cavitary lesions especially for patients whose diagnosis could not be made by sputum and bronchoscopic procedures and who are not suitable for cutting needle biopsy. PMID:23991300

Synthesis of Keratin-based Nanofiber for Biomedical Engineering.

PubMed

Thompson, Zanshe S; Rijal, Nava P; Jarvis, David; Edwards, Angela; Bhattarai, Narayan

2016-02-07

Electrospinning, due to its versatility and potential for applications in various fields, is being frequently used to fabricate nanofibers. Production of these porous nanofibers is of great interest due to their unique physiochemical properties. Here we elaborate on the fabrication of keratin containing poly (ε-caprolactone) (PCL) nanofibers (i.e., PCL/keratin composite fiber). Water soluble keratin was first extracted from human hair and mixed with PCL in different ratios. The blended solution of PCL/keratin was transformed into nanofibrous membranes using a laboratory designed electrospinning set up. Fiber morphology and mechanical properties of the obtained nanofiber were observed and measured using scanning electron microscopy and tensile tester. Furthermore, degradability and chemical properties of the nanofiber were studied by FTIR. SEM images showed uniform surface morphology for PCL/keratin fibers of different compositions. These PCL/keratin fibers also showed excellent mechanical properties such as Young's modulus and failure point. Fibroblast cells were able to attach and proliferate thus proving good cell viability. Based on the characteristics discussed above, we can strongly argue that the blended nanofibers of natural and synthetic polymers can represent an excellent development of composite materials that can be used for different biomedical applications.

Prevention of intra-abdominal adhesion by bi-layer electrospun membrane.

PubMed

Jiang, Shichao; Wang, Wei; Yan, Hede; Fan, Cunyi

2013-06-04

The aim of this study was to compare the anti-adhesion efficacy of a bi-layer electrospun fibrous membrane consisting of hyaluronic acid-loaded poly(ε-caprolactone) (PCL) fibrous membrane as the inner layer and PCL fibrous membrane as the outer layer with a single-layer PCL electrospun fibrous membrane in a rat cecum abrasion model. The rat model utilized a cecal abrasion and abdominal wall insult surgical protocol. The bi-layer and PCL membranes were applied between the cecum and the abdominal wall, respectively. Control animals did not receive any treatment. After postoperative day 14, a visual semiquantitative grading scale was used to grade the extent of adhesion. Histological analysis was performed to reveal the features of adhesion tissues. Bi-layer membrane treated animals showed significantly lower adhesion scores than control animals (p < 0.05) and a lower adhesion score compared with the PCL membrane. Histological analysis of the bi-layer membrane treated rat rarely demonstrated tissue adhesion while that of the PCL membrane treated rat and control rat showed loose and dense adhesion tissues, respectively. Bi-layer membrane can efficiently prevent adhesion formation in abdominal cavity and showed a significantly decreased adhesion tissue formation compared with the control.

Gray matter changes in right superior temporal gyrus in criminal psychopaths. Evidence from voxel-based morphometry.

PubMed

Müller, Jürgen L; Gänssbauer, Susanne; Sommer, Monika; Döhnel, Katrin; Weber, Tatjana; Schmidt-Wilcke, Tobias; Hajak, Göran

2008-08-30

"Psychopathy" according to the PCL-R describes a specific subgroup of antisocial personality disorder with a high risk for criminal relapses. Lesion and imaging studies point towards frontal or temporal brain regions connected with disturbed social behavior, antisocial personality disorder (APD) and psychopathy. Morphologically, some studies described a reduced prefrontal brain volume, whereas others reported on temporal lobe atrophy. To further investigate whether participants with psychopathy according to the Psychopathy Checklist-Revised Version (PCL-R) show abnormalities in brain structure, we used voxel-based morphometry (VBM) to investigate region-specific changes in gray matter in 17 forensic male inpatients with high PCL-R scores (PCL-R>28) and 17 male control subjects with low PCL-R scores (PCL<10). We found significant gray matter reductions in frontal and temporal brain regions in psychopaths compared with controls. In particular, we found a highly significant volume loss in the right superior temporal gyrus. This is the first study to show that psychopathy is associated with a decrease in gray matter in both frontal and temporal brain regions, in particular in the right superior temporal gyrus, supporting the hypothesis that a disturbed frontotemporal network is critically involved in the pathogenesis of psychopathy.

In vitro cytotoxicity and antibacterial activity of silver-coated electrospun polycaprolactone/gelatine nanofibrous scaffolds.

PubMed

Lim, Mim Mim; Sultana, Naznin

2016-12-01

The development of nano-sized scaffolds with antibacterial properties that mimic the architecture of tissue is one of the challenges in tissue engineering. In this study, polycaprolactone (PCL) and PCL/gelatine (Ge) (70:30) nanofibrous scaffolds were fabricated using a less toxic and common solvent, formic acid and an electrospinning technique. Nanofibrous scaffolds were coated with silver (Ag) in different concentrations of silver nitrate (AgNO 3 ) aqueous solution (1.25, 2.5, 5, and 10 %) by using dipping method, drying and followed by ultraviolet (UV) photoreduction. The PCL/Ge (70:30) nanofibrous scaffold had an average fibre diameter of 155.60 ± 41.13 nm. Characterization showed that Ag was physically entrapped in both the PCL and PCL/Ge (70:30) nanofibrous scaffolds. Ag + ions release study was performed and showed much lesser release amount than the maximum toxic concentration of Ag + ions in human cells. Both scaffolds were non-toxic to cells and demonstrated antibacterial effects towards Gram-positive Bacillus cereus (B. cereus) and Gram-negative Escherichia coli (E. coli). The Ag/PCL/Ge (70:30) nanofibrous scaffold has potential for tissue engineering as it can protect wounds from bacterial infection and promote tissue regeneration.

Proprioception in patients with posterior cruciate ligament tears: A meta-analysis comparison of reconstructed and contralateral normal knees

PubMed Central

Ko, Seung-Nam

2017-01-01

Posterior cruciate ligament (PCL) reconstruction for patients with PCL insufficiency has been associated with postoperative improvements in proprioceptive function due to mechanoreceptor regeneration. However, it is unclear whether reconstructed PCL or contralateral normal knees have better proprioceptive function outcomes. This meta-analysis was designed to compare the proprioceptive function of reconstructed PCL or contralateral normal knees in patients with PCL insufficiency. All studies that compared proprioceptive function, as assessed with threshold to detect passive movement (TTDPM) or joint position sense (JPS) in PCL reconstructed or contralateral normal knees were included. JPS was calculated by reproducing passive positioning (RPP). Five studies met the inclusion/exclusion criteria for the meta-analysis. The proprioceptive function, defined as TTDPM (95% CI: 0.25 to 0.51°; P<0.00001) and RPP (95% CI: 0.19 to 0.45°; P<0.00001), was significantly different between the reconstructed PCL and contralateral normal knees. The mean difference in angle of error between the reconstructed PCL and contralateral normal knees was 0.06° greater in TTDPM than by RPP. In addition, results from subgroup analyses, based on the starting angles and the moving directions of the knee, that evaluated TTDPM at 15° flexion to 45° extension, TTDPM at 45° flexion to 110° flexion, RPP in flexion, and RPP in extension demonstrated that mean angles of error were significantly greater, by 0.38° (P = 0.0001), 0.36° (P = 0.02), 0.36° (P<0.00001), and 0.23° (P = 0.04), respectively, in reconstructed PCL than in contralateral normal knees. The proprioceptive function of PCL reconstructed knees was decreased, compared with contralateral normal knees, as determined by both TTDPM and RPP. In addition, the amount of loss of proprioception was greater in TTDPM than in RPP, even with minute differences. Results from subgroup analysis, that evaluated the mean angles of error in moving directions through RPP, suggested that the moving direction of flexion has a significantly greater mean for angles of error than the moving direction of extension. Although the level of differences between various parameters were statistically significant, further studies are needed to determine whether the small differences (>1°) of the loss of proprioception are clinically relevant. PMID:28922423

Characterization of progesterone profiles in fall-calving Norwegian Red cows.

PubMed

Garmo, R T; Martin, A D; Thuen, E; Havrevoll, Ø; Steinshamn, H; Prestløkken, E; Randby, A; Eknaes, M; Waldmann, A; Reksen, O

2009-10-01

Progesterone profiles in Norwegian Red cows were categorized, and associations between the occurrence of irregularities in the profiles and the commencement of luteal activity were investigated. The cows were managed in 3 feeding trials from 1994 to 2001 and from 2005 to 2008 at the Norwegian University of Life Sciences. The cows were followed from calving, and the milk samples collected represented 502 lactations from 302 cows. Milk samples for progesterone analysis were taken 3 times weekly from 1994 throughout 1998 and from 2005 to 2008 and 2 times weekly from 1999 to 2001. Commencement of luteal activity was defined as the first day of 2 consecutive measurements of progesterone concentration >or=3 ng/mL not earlier than 10 d after calving. Delayed ovulation type I was defined as consistently low progesterone concentration, <3 ng/mL for >or=50 d postpartum. Delayed ovulation type II was defined as prolonged interluteal interval with milk progesterone measurements <3 ng/mL for >or=12 d between 2 luteal phases. Persistent corpus luteum (PCL) type I was defined as delayed luteolysis with milk progesterone >or=3 ng/mL for >or=19 d during the first estrous cycle postpartum. Persistent corpus luteum type II was defined as delayed luteolysis with milk progesterone >or=3 ng/mL for >or=19 d during subsequent estrous cycles before first artificial insemination. Delayed ovulation type I was present in 14.7%, delayed ovulation type II in 2.8%, PCL type I in 6.7%, and PCL type II in 3.3% of the profiles. Commencement of luteal activity was related to milk yield, parity, PCL type I, and the summated occurrence of PCL type I and II. The least squares means for the interval to commencement of luteal activity were 24.2 d when PCL type I and II were present and 29.5 d when PCL type I and II were absent. The likelihood of pregnancy to first service was not affected in cows with a history of PCL when artificial insemination was carried out at progesterone concentrations <3 ng/mL (i.e., during estrus); however, cows that had experienced PCL were more likely to be inseminated during a luteal phase. The occurrence of delayed ovulation and PCL in Norwegian Red cows was less than that reported in most other dairy populations.

Biocorrosion and osteoconductivity of PCL/nHAp composite porous film-based coating of magnesium alloy

NASA Astrophysics Data System (ADS)

Abdal-hay, Abdalla; Amna, Touseef; Lim, Jae Kyoo

2013-04-01

The present study was aimed at designing a novel porous hydroxyapatite/poly(ɛ-caprolactone) (nHAp/PCL) hybrid nanocomposite matrix on a magnesium substrate with high and low porosity. The coated samples were prepared using a dip-coating technique in order to enhance the bioactivity and biocompatibility of the implant and to control the degradation rate of magnesium alloys. The mechanical and biocompatible properties of the coated and uncoated samples were investigated and an in vitro test for corrosion was conducted by electrochemical polarization and measurement of weight loss. The corrosion test results demonstrated that both the pristine PCL and nHAp/PCL composites showed good corrosion resistance in SBF. However, during the extended incubation time, the composite coatings exhibited more uniform and superior resistance to corrosion attack than pristine PCL, and were able to survive severe localized corrosion in physiological solution. Furthermore, the bioactivity of the composite film was determined by the rapid formation of uniform CaP nanoparticles on the sample surfaces during immersion in SBF. The mechanical integrity of the composite coatings displayed better performance (˜34% higher) than the uncoated samples. Finally, our results suggest that the nHAp incorporated with novel PCL composite membranes on magnesium substrates may serve as an excellent 3-D platform for cell attachment, proliferation, migration, and growth in bone tissue. This novel as-synthesized nHAp/PCL membrane on magnesium implants could be used as a potential material for orthopedic applications in the future.

Assessing the physical-chemical properties and stability of dapivirine-loaded polymeric nanoparticles.

PubMed

das Neves, José; Amiji, Mansoor; Bahia, Maria Fernanda; Sarmento, Bruno

2013-11-18

Nanocarriers may provide interesting delivery platforms for microbicide drugs and their characterization should be addressed early in development. Differently surface-engineered dapivirine-loaded, poly(epsilon-caprolactone) (PCL)-based nanoparticles (NPs) were obtained by nanoprecipitation using polyethylene oxide (PEO), sodium lauryl sulfate (SLS), or cetyltrimethylammonium bromide (CTAB) as surface modifiers. Physical-chemical properties of NP aqueous dispersions were evaluated upon storage at -20-40 °C for one year. NPs presented 170-200 nm in diameter, roundish-shape, low polydispersity index (≤0.18), and high drug association efficiency (≥97%) and loading (≥12.7%). NPs differed in zeta potential, depending on surface modifier (PEO: -27.9 mV; SLS: -54.7 mV; CTAB: +42.4 mV). No interactions among formulation components were detected by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR), except for SLS-PCL NPs. Colloidal properties of NPs were lost at -20 °C storage. Negatively charged NPs were stable up to one year at 5-40°C; as for CTAB-PCL NPs, particle aggregation was observed from 30 to 90 days of storage depending on temperature. Colloidal instability affected the in vitro drug release of CTAB-PCL NPs after 360 days. In any case, no degradation of dapivirine was apparent. Overall, PEO-PCL and SLS-PCL NPs presented suitable properties as nanocarriers for dapivirine. Conversely, CTAB-PCL NPs require additional strategies in order to increase stability. Copyright © 2013 Elsevier B.V. All rights reserved.

A thermoplastic/thermoset blend exhibiting thermal mending and reversible adhesion.

PubMed

Luo, Xiaofan; Ou, Runqing; Eberly, Daniel E; Singhal, Amit; Viratyaporn, Wantinee; Mather, Patrick T

2009-03-01

In this paper, we report on the development of a new and broadly applicable strategy to produce thermally mendable polymeric materials, demonstrated with an epoxy/poly(-caprolactone) (PCL) phase-separated blend. The initially miscible blend composed of 15.5 wt % PCL undergoes polymerization-induced phase separation during cross-linking of the epoxy, yielding a "bricks and mortar" morphology wherein the epoxy phase exists as interconnected spheres (bricks) interpenetrated with a percolating PCL matrix (mortar). The fully cured material is stiff, strong, and durable. A heating-induced "bleeding" behavior was witnessed in the form of spontaneous wetting of all free surfaces by the molten PCL phase, and this bleeding is capable of repairing damage by crack-wicking and subsequent recrystallization with only minor concomitant softening during that process. The observed bleeding is attributed to volumetric thermal expansion of PCL above its melting point in excess of epoxy brick expansion, which we term differential expansive bleeding (DEB). In controlled thermal-mending experiments, heating of a cracked specimen led to PCL extrusion from the bulk to yield a liquid layer bridging the crack gap. Upon cooling, a "scar" composed of PCL crystals formed at the site of the crack, restoring a significant portion of the mechanical strength. When a moderate force was applied to assist crack closure, thermal-mending efficiencies exceeded 100%. We further observed that the DEB phenomenon enables strong and facile adhesion of the same material to itself and to a variety of materials, without any requirement for macroscopic softening or flow.

Improvement of mechanical strength and osteogenic potential of calcium sulfate-based hydroxyapatite 3-dimensional printed scaffolds by ε-polycarbonate coating.

PubMed

Kim, Beom-Su; Yang, Sun-Sik; Park, Ho; Lee, Se-Hwan; Cho, Young-Sam; Lee, Jun

2017-09-01

Powder-based three-dimensional (3D) printing is an excellent method to fabricate complex-shaped scaffolds for tissue engineering. However, their lower mechanical strength restricts their application in bone tissue engineering. Here, we created a 3D-printed scaffold coated with a ε-polycaprolactone (PCL) polymer solution (5 and 10 w/v %) to improve the mechanical strength of the scaffold. The 3D scaffold was fabricated from calcium sulfate hemihydrate powder (CaSO 4 -1/2 H 2 O), transformed into hydroxyapatite (HAp) by treatment with a hydrothermal reaction in an NH 4 H 2 PO 4 solution. The surface properties and composition of the scaffold were evaluated using scanning electron microscopy and X-ray diffraction analysis. We demonstrated that the 3D scaffold coated with PCL had an improved mechanical modulus. Coating with 5 and 10% PCL increased the compressive strength significantly, by about 2-fold and 4-fold, respectively, compared with that of uncoated scaffolds. However, the porosity was reduced significantly by coating with 10% PCL. In vitro biological evaluation demonstrated that MG-63 cells adhered well and proliferated on the 3D scaffold coated with PCL, and the scaffold was not cytotoxic. In addition, alkaline phosphatase activity and real time polymerase chain reaction demonstrated that osteoblast differentiation also improved in the PCL-coated 3D scaffolds. These results indicated that PCL polymer coating could improve the compressive strength and biocompatibility of 3D HAp scaffolds for bone tissue engineering applications.

Active angular alignment of gauge blocks in double-ended interferometers.

PubMed

Buchta, Zdeněk; Reřucha, Simon; Hucl, Václav; Cížek, Martin; Sarbort, Martin; Lazar, Josef; Cíp, Ondřej

2013-09-27

This paper presents a method implemented in a system for automatic contactless calibration of gauge blocks designed at ISI ASCR. The system combines low-coherence interferometry and laser interferometry, where the first identifies the gauge block sides position and the second one measures the gauge block length itself. A crucial part of the system is the algorithm for gauge block alignment to the measuring beam which is able to compensate the gauge block lateral and longitudinal tilt up to 0.141 mrad. The algorithm is also important for the gauge block position monitoring during its length measurement.

Active Angular Alignment of Gauge Blocks in Double-Ended Interferometers

PubMed Central

Buchta, Zdeněk; Řeřucha, Šimon; Hucl, Václav; Čížek, Martin; Šarbort, Martin; Lazar, Josef; Číp, Ondřej

2013-01-01

This paper presents a method implemented in a system for automatic contactless calibration of gauge blocks designed at ISI ASCR. The system combines low-coherence interferometry and laser interferometry, where the first identifies the gauge block sides position and the second one measures the gauge block length itself. A crucial part of the system is the algorithm for gauge block alignment to the measuring beam which is able to compensate the gauge block lateral and longitudinal tilt up to 0.141 mrad. The algorithm is also important for the gauge block position monitoring during its length measurement. PMID:24084107

Folate-conjugated pH-responsive nanocarrier designed for active tumor targeting and controlled release of doxorubicin

NASA Astrophysics Data System (ADS)

Wei, Lulu; Lu, Beibei; Cui, Lin; Peng, Xueying; Wu, Jianning; Li, Deqiang; Liu, Zhiyong; Guo, Xuhong

2017-12-01

A novel type of amphiphilic pH-responsive folate-poly(ɛ-caprolactone)- block-poly(2-hydroxyethylmethacrylate)- co-poly(2-(dimethylamino)-ethylmethacrylate) (FA-PCL- b-P(HEMA- co-DMAEMA)) (MFP) block copolymers were designed and synthesized via atom transfer radical polymerization (ATRP) and ring opening polymerization (ROP) techniques. The molecular structures of the copolymers were confirmed with 1H NMR, FTIR and GPC measurements. The critical micelle concentration (CMC) of MFP in aqueous solution was extremely low (about 6.54 mg/L). The in vitro release behavior of DOX-loaded micelles was significantly accelerated when the pH value of solution decreased from 7.4 to 5.0. In vitro antitumor efficiency was evaluated by incubating DOX-loaded micelles with Hela cells. The results demonstrated that this copolymer possessed excellent biocompatibility, and FA-decorated micelles MFP showed higher cellular uptake than those micelles without the FA moiety, indicating their unique targetability. These folate-conjugated biodegradable micelles are highly promising for targeted cancer chemothe-rapy.

On the Viability of PTSD Checklist (PCL) Short Form Use: Analyses from Mississippi Gulf Coast Hurricane Katrina Survivors

ERIC Educational Resources Information Center

Hirschel, Michael J.; Schulenberg, Stefan E.

2010-01-01

One measure commonly used to assess posttraumatic stress disorder is the PTSD Checklist (PCL). Lang and Stein (2005) extracted 4 subsets of PCL items, validating 2 of them for possible use in screening in primary care settings. The viability of the 4 item subsets was evaluated psychometrically in the present study with a sample of Hurricane…

Psychopathy and the Combination of Psychopathy and Sexual Deviance as Predictors of Sexual Recidivism: Meta-Analytic Findings Using the Psychopathy Checklist-Revised

ERIC Educational Resources Information Center

Hawes, Samuel W.; Boccaccini, Marcus T.; Murrie, Daniel C.

2013-01-01

Clinicians routinely administer Hare's (2003) Psychopathy Checklist-Revised (PCL-R) to sex offenders and report PCL-R scores as meaningful predictors of recidivism risk. Although a 2005 meta-analysis reported a small (d = 0.29) association between PCL-R scores and sexual recidivism (Hanson & Morton-Bourgon, 2005), no meta-analysis has examined…

Measurement of Diffusion in Entangled Rod-Coil Triblock Copolymers

NASA Astrophysics Data System (ADS)

Olsen, B. D.; Wang, M.

2012-02-01

Although rod-coil block copolymers have attracted increasing attention for functional nanomaterials, their dynamics relevant to self-assembly and processing have not been widely investigated. Because the rod and coil blocks have different reptation behavior and persistence lengths, the mechanism by which block copolymers will diffuse is unclear. In order to understand the effect of the rigid block on reptation, tracer diffusion of a coil-rod-coil block copolymer through an entangled coil polymer matrix was experimentally measured. A monodisperse, high molecular weight coil-rod-coil triblock was synthesized using artificial protein engineering to prepare the helical rod and bioconjugaiton of poly(ethylene glycol) coils to produce the final triblock. Diffusion measurements were performed using Forced Rayleigh scattering (FRS), at varying ratios of the rod length to entanglement length, where genetic engineering is used to control the protein rod length and the polymer matrix concentration controls the entanglement length. As compared to PEO homopolymer tracers, the coil-rod-coil triblocks show markedly slower diffusion, suggesting that the mismatch between rod and coil reptation mechanisms results in hindered diffusion of these molecules in the entangled state.

Curcumin mediated down-regulation of αV β3 integrin and up-regulation of pyruvate dehydrogenase kinase 4 (PDK4) in Erlotinib resistant SW480 colon cancer cells.

PubMed

Javadi, Samira; Rostamizadeh, Kobra; Hejazi, Jalal; Parsa, Maliheh; Fathi, Mojtaba

2018-02-01

Erlotinib is a potent, selective, and orally active inhibitor of the epidermal growth factor receptor, but the development of erlotinib resistance during chemotherapy can lead to treatment failure. To shed light on the erlotinib-resistant pathway, this study investigated the effect of combination therapy using curcumin- and erlotinib-loaded nanoparticles on the expression of α v β 3 integrin and pyruvate dehydrogenase kinase 4 (PDK4) in an erlotinib-resistant SW480 colon cancer cell line. An erlotinib-resistant SW480 colon cancer cell line was produced by long-term exposure to erlotinib. Curcumin-loaded Methoxy poly ethylene glycol Poly caprolactone (cur/mPEG-PCL) and erlotinib-loaded mPEG-PCL (erl/mPEG-PCL) micelles were provided using a single step nanoprecipitation method and used as combination therapy of resistant SW480 cancer cells. After that, gene expression levels of PDK4, αv, and β3 mRNA were determined by the semiquantitative reverse transcription-polymerase chain reaction. Protein levels of whole α v β 3 integrin were evaluated using the enzyme-linked immunosorbent assay method. In SW480 cell line, the IC50 of nonresistant and resistant cells was 87.6 ± 1.2 nM and 19.1 ± 0.14 μM, for erlotinib and it was about 21.8 and 30 μM for curcumin, respectively. Although PDK4 expression was not significantly different in resistant and nonresistant cells, its expression was up regulated (1.4 fold) in resistant cells by a combination therapy of cur/mPEG-PCL at a dose of 3 μM and erl/mPEG-PCL at a dose of 5 μM. β 3 mRNA and the protein level of whole α v β 3 integrin was significantly higher in resistant SW480 cells as compared with those in nonresistant cells. In terms of treatment, a combination of 6-μM cur/mPEG-PCL and 5-μM erl/mPEG-PCL down regulated β 3 gene expression 6.6-fold in resistant cells as compared with nonresistant cells. At the protein level, a combination of 3-μM-cur/mPEG-PCL and 10-μM erl/mPEG-PCL reduced α v β 3 protein in resistant cells. The results indicated that combination therapy using cur/mPEG-PCL and erl/mPEG-PCL could decrease α v β 3 integrin expression and increase PDK4 gene expression in resistant colon cancer cells, which may have effects on drug resistance signaling pathways. Copyright © 2017 John Wiley & Sons, Ltd.

Multifunctional liposomes for enhanced anti-cancer therapy

NASA Astrophysics Data System (ADS)

Falcao, Claudio Borges

2011-12-01

Macromolecular drugs have great promises for cancer treatment, such as the pro-apoptotic peptide D-(KLAKLAK)2 and the bcl-2 antisense oligodeoxynucleotide G3139. However, these macromolecules require efficient drug carriers, like liposomes, to deliver them inside cells. Also, if these macromolecules can be combined in a single liposome, the cancer cell killing will be greater than using just one. With this possibility in mind, cationic liposomes (CLs) were elaborated to encapsulate both macromolecules and deliver them inside cells. Later, surface modification of CLs was investigated through the addition of polyethylene glycol (PEG) to obtain long-circulating liposomes. CLs were prepared through charge alternation among D-(KLAKLAK)2 , G3139 and DOTAP. These liposomes were characterized with particle size and zeta-potential measurements, antisense entrapment and peptide loading efficiency. The in vitro effects of CL formulations were tested with B16(F10) cells through viability studies, uptake assay and detection of apoptosis. CL formulations were also applied in vivo in B16(F10) tumor-bearing mice through intratumoral injections, and tumor growth inhibition and detection of apoptosis were evaluated. Next, the mechanism of action of the CL formulations was investigated by Western blotting. Later, PEG was incorporated at increasing amounts to the liposomes to determine which concentration can better prevent interactions between PEG-cationic liposomes (PCL) and B16(F10) cells. Next, pH-cleavable PEG was prepared and then added to the liposomes in the same amount that PEG in PCL could decrease interaction with cells. Finally, cell viability studies were performed with CL, PCL and pH-sensitive PCL (pH-PCL) formulations after pre-incubation at pH 7.4 or at pH 5.0. Positively charged CL particles were obtained after encapsulation of negatively charged D-(KLAKLAK)2/G3139 complexes. In vitro , CLs containing D-(KLAKLAK)2/G3139 complexes could reduce B16(F10) cell viability with half of the concentration needed for G3139 alone in CL to reduce the cell viability by 40%. Also, it was found greater apoptotic signal in cells treated with CLs containing D-(KLAKLAK)2/G3139 complexes than CLs with G3139 only. In vivo, D-(KLAKLAK) 2/G3139 complexes in CL significantly inhibited tumor growth compared to the saline treated group, through apoptosis induction. However, the mechanism involved in cell death by apoptosis seems to be independent of reduction of bcl-2 protein levels. PEG2000 at 1% mol could significantly reduce activity of PCL formulation towards B16(F10) cells compared to CLs. After pre-incubation at pH 7.4, PCL and pH-PCL had decreased activity compared to CL towards B16(F10) cells. After pre-incubation at pH 5.0, while CL and PCL had the same activity with the cells as in neutral pH, pH-PCL formulation had its PEG cleaved and its cytotoxicity was restored against the melanoma cells. Thus, D-(KLAKLAK)2/G3139 complexes in CL had enhanced anti-cancer therapy, through apoptosis, than G3139 alone in CL in vitro and in vivo. In vitro, PCL and pH-PCL particles obtained can have a prolonged blood residence time, and, once a tumor tissue is reached, pH-PCL can have its cytotoxicity restored because of hydrolysis of cleavable PEG at a lowered pH.

Environmental fate and effect of biodegradable electro-spun scaffolds (biomaterial)-a case study.

PubMed

Irizar, A; Amorim, M J B; Fuller, K P; Zeugolis, D I; Scott-Fordsmand, J J

2018-04-30

Poly-ε-caprolactone (PCL) based medical devices are increasingly produced and thus, their presence in the environment is likely to increase. The present study analysed the biodegradation of PCL electro-spun scaffolds (alone) and PCL electro-spun scaffolds coated with human recombinant (hR) collagen and Bovine Achilles tendon (BAT) collagen in sewage sludge and in soil. Additionally, an eco-toxicological test with the model organism Enchytraeus crypticus was performed to assess environmental hazard of the produced materials in soils. The electro-spun scaffolds were exposed to activated sludge and three different soils for various time periods (0-7-14-21-28-56-180 days); subsequently the degradation was determined by weight loss and microscopical analysis. Although no toxicity occurred in terms of Enchytraeus crypticus reproduction, our data indicate that biodegradation was dependent on the coating of the material and exposure condition. Further, only partial PCL decomposition was possible in sewage treatment plants. Collectively, these data indicate that electro-spun PCL scaffolds are transferred to amended soils.

Comparative evaluation of in vitro parameters of tamoxifen citrate loaded poly(lactide-co-glycolide), poly(epsilon-caprolactone) and chitosan nanoparticles.

PubMed

Cirpanli, Y; Yerlikaya, F; Ozturk, K; Erdogar, N; Launay, M; Gegu, C; Leturgez, T; Bilensoy, E; Calis, S; Capan, Y

2010-12-01

Tamoxifen (TAM), the clinical choice for the antiestrogen treatment of advanced or metastatic breast cancer, was formulated in nanoparticulate carrier systems in the form of poly(lactide-co-glycolide) (PLGA), poly-epsilon-caprolactone (PCL) and chitosan (CS) nanoparticles. The PLGA and PCL nanoparticles were prepared by a nanoprecipitation technique whereas the CS nanoparticles were prepared by the ionic gelation method. Mean particle sizes were under 260 nm for PLGA and PCL nanoparticles and around 400 nm for CS nanoparticles. Polydispersity indices were less than 0.4 for all formulations. Zeta potential values were positive for TAM loaded nanoparticles because of the positive charge of the drug. Drug loading values were significantly higher for PCL nanoparticles when compared to PLGA and CS nanoparticles. All nanoparticle formulations exhibited controlled release properties. These results indicate that TAM loaded PLGA, PCL and CS nanoparticles may provide promising carrier systems for tumor targeting.

Factor structure and construct validity of the psychopathic personality inventory in a forensic sample.

PubMed

Gonsalves, Valerie M; McLawsen, Julia E; Huss, Matthew T; Scalora, Mario J

2013-01-01

A wealth of research has underscored the strong relationship between PCL-R scores and recidivism. However, mounting criticism cites the PCL-R's cumbersome administration procedures and failure to adequately measure core features associated with the construct of psychopathy (Skeem, Polaschek, Patrick, & Lilienfeld, 2011). In light of these concerns, this study examined the PPI and the PPI-R, which were designed to measure core personality features associated with psychopathy (Lilienfeld & Andrews, 1996; Lilienfeld & Widows, 2005). Study one examined the PPI relative to the PCL-R and examined its factor structure. The instruments shared few significant correlations and neither the PCL-R nor the PPI significantly predicted recidivism. Study two examined the PPI-R relative to the PCL-R, the PPI, both history of violence and future criminal activity and measure of related constructs. The PPI-R was significantly correlated with measures of empathy and criminal thinking and the factors were related to a history of violence and predicted future violent criminal behavior. Copyright © 2013 Elsevier Ltd. All rights reserved.

Silver-Loaded Cellulose Acetate-g-Poly(ε-caprolactone) Composites

NASA Astrophysics Data System (ADS)

Tuburan, CR; Dela Rosa, LE; Reyes, LQ

2017-06-01

Cellulose acetate (CA) was grafted with poly(ε-caprolactone) PCL oligomers via the ring-opening of ε-caprolactone (ε-CL) monomer initiated by the hydroxyl functionality of CA. The incorporation of short PCL oligomers in CA’s structure caused the transformation of it crystalline domains into amorphous phases (internal plasticization) as observed by differential scanning calorimetry (DSC). Another evidence of plasticization induced by grafting was the significant reduction of the degradation temperature and stiffness of the copolymers. Proton Nuclear Magnetic Resonance (1H-NMR), Fourier-Transform Infrared (FTIR) Spectroscopies and Gel Permeation Chromatography (GPC) verified success the grafting as suggested by the attachment of PCL on the glucose ring and increase in polymer molecular weights after the reaction. Due to the good films forming ability of the synthesized CA grafted with PCL (CA-g-PCL) material, it was loaded with silver nitrate (AgNO3) and the composite was observed to be have bactericidal against a gram negative bacteria, Escherichia coli, and a gram positive bacteria, Bacillus subtilis.

Non-Fouling Biodegradable Poly(ϵ-caprolactone) Nanofibers for Tissue Engineering.

PubMed

Kostina, Nina Yu; Pop-Georgievski, Ognen; Bachmann, Michael; Neykova, Neda; Bruns, Michael; Michálek, Jiří; Bastmeyer, Martin; Rodriguez-Emmenegger, Cesar

2016-01-01

Poly(ϵ-caprolactone) (PCL) nanofibers are very attractive materials for tissue engineering (TE) due to their degradability and structural similarity to the extracellular matrix (ECM). However, upon exposure to biological media, their surface is rapidly fouled by proteins and cells, which may lead to inflammation and foreign body reaction. In this study, an approach for the modification of PCL nanofibers to prevent protein fouling from biological fluids and subsequent cell adhesion is introduced. A biomimetic polydopamine (PDA) layer was deposited on the surface of the PCL nanofibers and four types of antifouling polymer brushes were grown by surface-initiated atom transfer radical polymerization (SI-ATRP) from initiator moieties covalently attached to the PDA layer. Cell adhesion was assessed with mouse embryonic fibroblasts (MEFs). MEFs rapidly adhered and formed cell-matrix adhesions (CMAs) with PCL and PCL-PDA nanofibers. Importantly, the nanofibers modified with antifouling polymer brushes were able to suppress non-specific protein adsorption and thereby cell adhesion. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The deposition of thin titanium-nitrogen coatings on the surface of PCL-based scaffolds for vascular tissue engineering

NASA Astrophysics Data System (ADS)

Kudryavtseva, Valeriya; Stankevich, Ksenia; Kibler, Elina; Golovkin, Alexey; Mishanin, Alexander; Bolbasov, Evgeny; Choynzonov, Evgeny; Tverdokhlebov, Sergei

2018-04-01

Biodegradable polymer scaffolds for tissue engineering is a promising technology for therapies of patients suffering from the loss of tissue or its function including cardiac tissues. However, limitations such as hydrophobicity of polymers prevent cell attachment, cell conductivity, and endothelialization. Plasma modification of polymers allows producing materials for an impressive range of applications due to their unique properties. Here, we demonstrate the possibility of bioresorbable electrospun polycaprolacton (PCL) scaffold surface modification by reactive magnetron sputtering of the titanium target in a nitrogen atmosphere. The influence of the plasma treatment time on the structure and properties of electrospun PCL scaffolds was studied. We show that the plasma treatment does not change the physico-mechanical properties of electrospun PCL scaffolds, leads to an increase in PCL scaffold biocompatibility, and, simultaneously, increases their hydrophilicity. In conclusion, this modification method opens a route to producing scaffolds with enhanced biocompatibility for tissue engineered vascular grafts.

Maltose conjugation to PCL: Advanced structural characterization and preliminary biological properties

NASA Astrophysics Data System (ADS)

Secchi, Valeria; Guizzardi, Roberto; Russo, Laura; Pastori, Valentina; Lecchi, Marzia; Franchi, Stefano; Iucci, Giovanna; Battocchio, Chiara; Cipolla, Laura

2018-05-01

The emerging trends in regenerative medicine rely among others on biomaterial-based therapies, with the use of biomaterials as a central delivery system for biochemical and physical cues to manipulate transplanted or ingrowth cells and to orchestrate tissue regeneration. Cell adhesion properties of a biomaterial strongly depend on its surface characteristics. Among others poly(ε-caprolactone) (PCL) is a biocompatible and biodegradable material with low cytotoxicity that is widely adopted as synthetic polymer in several applications. However, it is hydrophobic, which limits its use in tissue engineering. In order to improve its hydrophilicity and cellular compatibility, PCL surface was grafted with maltose through a two-step procedure in which controlled aminolysis of PCL ester bonds by hexanediamine was followed by reductive amination with the carbohydrate reducing end. The modified PCL surface was then characterized in detail by x-ray Photoelectron Spectroscopy (XPS) and Near Edge x-ray Absorption Fine Structure (NEXAFS) spectroscopies. In addition, the biocompatibility of the proposed biomaterial was investigated in preliminary biological assays.

Psychopathy and community violence among civil psychiatric patients: results from the MacArthur Violence Risk Assessment Study.

PubMed

Skeem, J L; Mulvey, E P

2001-06-01

Although psychopathy is recognized as a relatively strong risk factor for violence among inmates and mentally disordered offenders, few studies have examined the extent to which its predictive power generalizes to civil psychiatric samples. Using data on 1,136 patients from the MacArthur Violence Risk Assessment project, this study examined whether the 2 scales that underlie the Psychopathy Checklist: Screening Version (PCL:SV) measure a unique personality construct that predicts violence among civil patients. The results indicate that the PCL:SV is a relatively strong predictor of violence. The PCL:SV's predictive power is substantially reduced, but remains significant, after controlling for a host of covariates that reflect antisocial behavior and personality disorders other than psychopathy. However, the predictive power of the PCL:SV is not based on its assessment of the core traits of psychopathy, as traditionally construed. Implications for the 2-factor model that underlies the PCL measures and for risk assessment practice are discussed.

Implementation of poly(ε-caprolactone) sheet-based shape-memory polymer microvalves into plastic-based microfluidic devices

NASA Astrophysics Data System (ADS)

Jiang, Chenyang; Uto, Koichiro; Ebara, Mitsuhiro; Aoyagi, Takao; Ichiki, Takanori

2015-06-01

Implementation of shape-memory polymer (SMP) sheet-based microvalves into plastic-based microfluidic devices has been studied toward the use in disposable and mass producible micro total analysis devices. Poly(ε-caprolactone) (PCL) and poly(methyl methacrylate-co-styrene) (MS) were used as SMP and main substrate materials, respectively. Bonding between PCL sheets and MS plates was the critical issue in the practical implementation. We found the pristine PCL sheet has relatively rough surface with Ra of 85.14 nm, which is the cause of poor bonding. Hence, by introducing the post-anneal treatment with sandwiched between two flat glass plates, the PCL surface could be smoothed to Ra of 12.50 nm, and tight bonding could be obtained. Consequently, microfluidic devices consisting of plastic/PCL/plastic layers were successfully fabricated and therein the actuation of SMP valves without any leakage was demonstrated. The present technology is expected to be applicable to disposable microfluidic devices as required for point-of-care testing.

Effect of oxygen plasma etching on pore size-controlled 3D polycaprolactone scaffolds for enhancing the early new bone formation in rabbit calvaria.

PubMed

Kook, Min-Suk; Roh, Hee-Sang; Kim, Byung-Hoon

2018-05-02

This study was to investigate the effects of O 2 plasma-etching of the 3D polycaprolactone (PCL) scaffold surface on preosteoblast cell proliferation and differentiation, and early new bone formation. The PCL scaffolds were fabricated by 3D printing technique. After O 2 plasma treatment, surface characterizations were examined by scanning electron microscopy, atomic force microscopy, and contact angle. MTT assay was used to determine cell proliferation. To investigate the early new bone formation, rabbits were sacrificed at 2 weeks for histological analyses. As the O 2 plasma etching time is increased, roughness and hydrophilicity of the PCL scaffold surface increased. The cell proliferation and differentiation on plasma-etched samples was significantly increased than on untreated samples. At 2 weeks, early new bone formation in O 2 plasma-etched PCL scaffolds was the higher than that of untreated scaffolds. The O 2 plasma-etched PCL scaffolds showed increased preosteoblast differentiation as well as increased new bone formation.

Integrating sol-gel with cold plasmas modified porous polycaprolactone membranes for the drug-release of silver-sulfadiazine and ketoprofen

NASA Astrophysics Data System (ADS)

Mangindaan, Dave; Chen, Chao-Ting; Wang, Meng-Jiy

2012-12-01

A controlled release system composed of surface modified porous polycaprolactone (PCL) membranes combined with a layer of tetraorthosilicate (TEOS)-chitosan sol-gel was reported in this study. PCL is a hydrophobic, semi-crystalline, and biodegradable polymer with a relatively slow degradation rate. The drugs chosen for release experiments were silver-sulfadiazine (AgSD) and ketoprofen which were impregnated in the TEOS-chitosan sol-gel. The surface modification was achieved by O2 plasma and the surfaces were characterized by water contact angle (WCA) measurements, atomic force microscope (AFM), scanning electron microscope and electron spectroscopy for chemical analysis (ESCA). The results showed that the release of AgSD on O2 plasma treated porous PCL membranes was prolonged when compared with the pristine sample. On the contrary, the release rate of ketoprofen revealed no significant difference on pristine and plasma treated PCL membranes. The prepared PCL membranes showed good biocompatibility for the wound dressing biomaterial applications.

Development of a Spirulina Extract/Alginate-Imbedded PCL Nanofibrous Cosmetic Patch.

PubMed

Byeon, Seon Yeong; Cho, Myung Kwon; Shim, Kyou Hee; Kim, Hye Jin; Song, Hyeon Gi; Shin, Hwa Sung

2017-09-28

Cosmetic patches have recently been developed as skin products for personal care owing to rapid advances in the technology of delivery of active ingredients, moisture, and adhesiveness to skin. Alginate and Spirulina are typical marine resources used in cosmetic products. This research involved the development of a Spirulina extract-impregnated alginate nanofiber cosmetic patch supported by a polycaprolactone (PCL) nanofiber cover ( Spi /Alg-PCL NF patch). In addition to the ability of alginate to affect moisture and adhesiveness to skin, the impregnation of Spirulina extract strengthened those abilities as well as its own bioactive effectiveness. All fabrication processing steps were undertaken in aqueous solution. The three components (alginate, Spirulina extract, and PCL) had no detected cytotoxicity in human keratinocyte cell-based examination. In addition, wetting the pre-dried patch on the skin resulted in the Spirulina extract being released within 30 min. The results indicate the excellence of the Spi /Alg-PCL NF patch as a skin-care cosmetic device.

Effects of hydrogen bonding between pyrrole-2-carboxaldehyde and nearest polar and nonpolar environment

NASA Astrophysics Data System (ADS)

Rana, Meenakshi; Chowdhury, Papia

2017-10-01

The present paper represents dominant effects of hydrogen bonding on the existence of different molecular aggregates in one of the heterocyclic pyrrole system: pyrrole-2-carboxaldehyde (PCL). Theoretical and experimental Raman spectral evidence verifies the existence of different molecular aggregates like dimeric, monomeric, hydrated complex states in PCL. Atoms in molecules (AIMs) analysis and fluorescence decay profile provide a strong signature of intermolecular hydrogen bonding (IerHB) as the possible reason for the existence of cis form of dimeric (X) molecular aggregates. The high remnant polarization of 3.13 μCcm- 2 and smaller dielectric loss in solid form of PCL arise due to in X by ordering of dipoles as a result of IerHB. A remarkable high ferroelectric response in solid phase makes PCL a desirable candidate to be used as raw material for energy storage devices. For solution phase, in presence of external hydroxylic environment, PCL reacts with external water molecules through weak IerHB and creates different hydrated PCL/(H2O)n complexes by creating water bridge with number of water molecules from 1 to n. An increasing number of water molecules helps to form stronger hydrated complex by separation of charges by lowering the transferring energy barrier.

An additive manufacturing-based PCL-alginate-chondrocyte bioprinted scaffold for cartilage tissue engineering.

PubMed

Kundu, Joydip; Shim, Jin-Hyung; Jang, Jinah; Kim, Sung-Won; Cho, Dong-Woo

2015-11-01

Regenerative medicine is targeted to improve, restore or replace damaged tissues or organs using a combination of cells, materials and growth factors. Both tissue engineering and developmental biology currently deal with the process of tissue self-assembly and extracellular matrix (ECM) deposition. In this investigation, additive manufacturing (AM) with a multihead deposition system (MHDS) was used to fabricate three-dimensional (3D) cell-printed scaffolds using layer-by-layer (LBL) deposition of polycaprolactone (PCL) and chondrocyte cell-encapsulated alginate hydrogel. Appropriate cell dispensing conditions and optimum alginate concentrations for maintaining cell viability were determined. In vitro cell-based biochemical assays were performed to determine glycosaminoglycans (GAGs), DNA and total collagen contents from different PCL-alginate gel constructs. PCL-alginate gels containing transforming growth factor-β (TGFβ) showed higher ECM formation. The 3D cell-printed scaffolds of PCL-alginate gel were implanted in the dorsal subcutaneous spaces of female nude mice. Histochemical [Alcian blue and haematoxylin and eosin (H&E) staining] and immunohistochemical (type II collagen) analyses of the retrieved implants after 4 weeks revealed enhanced cartilage tissue and type II collagen fibril formation in the PCL-alginate gel (+TGFβ) hybrid scaffold. In conclusion, we present an innovative cell-printed scaffold for cartilage regeneration fabricated by an advanced bioprinting technology. Copyright © 2013 John Wiley & Sons, Ltd.

Chondroitin sulfate immobilization at the surface of electrospun nanofiber meshes for cartilage tissue regeneration approaches

NASA Astrophysics Data System (ADS)

Piai, Juliana Francis; da Silva, Marta Alves; Martins, Albino; Torres, Ana Bela; Faria, Susana; Reis, Rui L.; Muniz, Edvani Curti; Neves, Nuno M.

2017-05-01

Aiming at improving the biocompatibility of biomaterial scaffolds, surface modification presents a way to preserve their mechanical properties and to improve the surface bioactivity. In this work, chondroitin sulfate (CS) was immobilized at the surface of electrospun poly(caprolactone) nanofiber meshes (PCL NFMs), previously functionalized by UV/O3 exposure and aminolysis. Contact angle, SEM, optical profilometry, FTIR, X-ray photoelectron spectroscopy techniques confirmed the success of CS-immobilization in PCL NFMs. Furthermore, CS-immobilized PCL NFMs showed lower roughness and higher hydrophilicity than the samples without CS. Human articular chondrocytes (hACs) were cultured on electrospun PCL NFMs with or without CS immobilization. It was observed that hACs proliferated through the entire time course of the experiment in both types of nanofibrous scaffolds, as well as for the production of glycosaminoglycans. Quantitative-PCR results demonstrated over-expression of cartilage-related genes such as Aggrecan, Collagen type II, COMP and Sox9 on both types of nanofibrous scaffolds. Morphological observations from SEM and LSCM revealed that hACs maintained their characteristic round shape and cellular agglomeration exclusively on PCL NFMs with CS immobilization. In conclusion, CS immobilization at the surface of PCL NFMs was achieved successfully and provides a valid platform enabling further surface functionalization methods in scaffolds to be developed for cartilage tissue engineering.

A novel therapy strategy for bile duct repair using tissue engineering technique: PCL/PLGA bilayered scaffold with hMSCs.

PubMed

Zong, Chen; Wang, Meicong; Yang, Fuchun; Chen, Guojun; Chen, Jiarong; Tang, Zihua; Liu, Quanwen; Gao, Changyou; Ma, Lie; Wang, Jinfu

2017-04-01

The current clinical treatments for complications caused by hepatobiliary surgery still have some inevitable weakness. The aim of the study was to fabricate a tissue-engineered bile duct that utilized a novel bilayered polymer scaffold combined with human bone marrow-derived mesenchymal stem cells (hMSCs) for new treatment of biliary disease. The biocompatibility of polycaprolactone (PCL) (PCL)/poly(lactide-co-glycolide) (PLGA) scaffold with hMSCs was first examined, and the hMSC-PCL/PLGA constructs (MPPCs) prepared. The MPPCs and blank scaffolds were then transplanted into 18 pigs for evaluation its efficacy on bile duct repairing, respectively. In vitro, the PCL/PLGA scaffold was verified to support the adhesion, proliferation and matrix deposition of hMSCs. There was no sign of bile duct narrowing and cholestasis in all experimental animals. At 6 months, the MPPCs had a superior repairing effect on the bile duct injury, compared with the blank PCL/PLGA scaffolds. Therefore, the implanted scaffolds could not only support the biliary tract and allow free bile flow but also had direct or indirect positive effects on repair of injured bile duct. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

Prospective analysis using a patient-based health-related scale shows lower functional scores after posterior cruciate ligament reconstructions as compared with anterior cruciate ligament reconstructions of the knee.

PubMed

Ochiai, Satoshi; Hagino, Tetsuo; Senga, Shinya; Yamashita, Takashi; Ando, Takashi; Haro, Hirotaka

2016-09-01

This study evaluated the treatment outcome of posterior cruciate ligament (PCL) reconstruction using the Medical Outcome Study 36-item Short-Form Health Survey (SF-36), a patient-based quality of life (QOL) questionnaire comparing it with anterior cruciate ligament (ACL) reconstruction. Patients who underwent reconstruction at our center for PCL (n = 24) or ACL (n = 197) injury were studied. The patients were evaluated using SF-36, visual analogue scale (VAS) for knee pain, Lysholm scale, posterior or anterior tibial translation and range of motion (ROM) before surgery until 24 months after surgery. Results were compared. In the ACL group, all evaluation methods showed significant improvement after surgery. In the PCL group, however, improvement was observed in only three of eight subscales of the SF-36, Lysholm score and posterior tibial translation after surgery. In intergroup comparison, the PCL group showed inferior performance in three subscales of the SF-36, Lysholm score and ROM for flexion compared with the ACL group. The surgical outcome of PCL reconstruction was inferior to that of ACL reconstruction both in patient-based and conventional doctor-based assessments. An improved surgical technique for PCL is required.

Nanofiber Alignment Regulates NIH3T3 Cell Orientation and Cytoskeletal Gene Expression on Electrospun PCL+Gelatin Nanofibers.

PubMed

Fee, Timothy; Surianarayanan, Swetha; Downs, Crawford; Zhou, Yong; Berry, Joel

2016-01-01

To examine the influence of substrate topology on the behavior of fibroblasts, tissue engineering scaffolds were electrospun from polycaprolactone (PCL) and a blend of PCL and gelatin (PCL+Gel) to produce matrices with both random and aligned nanofibrous orientations. The addition of gelatin to the scaffold was shown to increase the hydrophilicity of the PCL matrix and to increase the proliferation of NIH3T3 cells compared to scaffolds of PCL alone. The orientation of nanofibers within the matrix did not have an effect on the proliferation of adherent cells, but cells on aligned substrates were shown to elongate and align parallel to the direction of substrate fiber alignment. A microarray of cyotoskeleton regulators was probed to examine differences in gene expression between cells grown on an aligned and randomly oriented substrates. It was found that transcriptional expression of eight genes was statistically different between the two conditions, with all of them being upregulated in the aligned condition. The proteins encoded by these genes are linked to production and polymerization of actin microfilaments, as well as focal adhesion assembly. Taken together, the data indicates NIH3T3 fibroblasts on aligned substrates align themselves parallel with their substrate and increase production of actin and focal adhesion related genes.

Psychometric Validation of the English and French Versions of the Posttraumatic Stress Disorder Checklist for DSM-5 (PCL-5).

PubMed

Ashbaugh, Andrea R; Houle-Johnson, Stephanie; Herbert, Christophe; El-Hage, Wissam; Brunet, Alain

2016-01-01

The purpose of this study is to assess the psychometric properties of a French version of the Posttraumatic Stress Disorder Checklist for DSM-5 (PCL-5), a self-report measure of posttraumatic stress disorder (PTSD) symptoms, and to further validate the existing English version of the measure. Undergraduate students (n = 838 English, n = 262 French) completed the PCL-5 as well as other self-report symptom measures of PTSD and depression online. Both the English and French versions PCL-5 total scores demonstrated excellent internal consistency (English: α = .95; French: α = .94), and strong convergent and divergent validity. Strong internal consistency was also observed for each of the four subscales for each version (α's > .79). Test-retest reliability for the French version of the measure was also very good (r = .89). Confirmatory factor analysis indicated that the four-factor DSM-5 model was not a good fit of the data. The seven-factor hybrid model best fit the data in each sample, but was only marginally superior to the six-factor anhedonia model. The French version of the PCL-5 demonstrated the same psychometric qualities as both the English version of the same measure and previous versions of the PCL. Thus clinicians serving French-speaking clients now have access to this highly used screening instrument. With regards to the structural validity of the PCL-5 and of the new PTSD diagnostic structure of the DSM-5, additional research is warranted. Replication of our results in clinical samples is much needed.

Psychometric Validation of the English and French Versions of the Posttraumatic Stress Disorder Checklist for DSM-5 (PCL-5)

PubMed Central

Ashbaugh, Andrea R.; Houle-Johnson, Stephanie; Herbert, Christophe; El-Hage, Wissam; Brunet, Alain

2016-01-01

The purpose of this study is to assess the psychometric properties of a French version of the Posttraumatic Stress Disorder Checklist for DSM-5 (PCL-5), a self-report measure of posttraumatic stress disorder (PTSD) symptoms, and to further validate the existing English version of the measure. Undergraduate students (n = 838 English, n = 262 French) completed the PCL-5 as well as other self-report symptom measures of PTSD and depression online. Both the English and French versions PCL-5 total scores demonstrated excellent internal consistency (English: α = .95; French: α = .94), and strong convergent and divergent validity. Strong internal consistency was also observed for each of the four subscales for each version (α’s > .79). Test-retest reliability for the French version of the measure was also very good (r = .89). Confirmatory factor analysis indicated that the four-factor DSM-5 model was not a good fit of the data. The seven-factor hybrid model best fit the data in each sample, but was only marginally superior to the six-factor anhedonia model. The French version of the PCL-5 demonstrated the same psychometric qualities as both the English version of the same measure and previous versions of the PCL. Thus clinicians serving French-speaking clients now have access to this highly used screening instrument. With regards to the structural validity of the PCL-5 and of the new PTSD diagnostic structure of the DSM-5, additional research is warranted. Replication of our results in clinical samples is much needed. PMID:27723815

Open-Source Selective Laser Sintering (OpenSLS) of Nylon and Biocompatible Polycaprolactone

PubMed Central

Paulsen, Samantha J.; Hwang, Daniel H.; Ta, Anderson H.; Yalacki, David R.; Schmidt, Tim; Miller, Jordan S.

2016-01-01

Selective Laser Sintering (SLS) is an additive manufacturing process that uses a laser to fuse powdered starting materials into solid 3D structures. Despite the potential for fabrication of complex, high-resolution structures with SLS using diverse starting materials (including biomaterials), prohibitive costs of commercial SLS systems have hindered the wide adoption of this technology in the scientific community. Here, we developed a low-cost, open-source SLS system (OpenSLS) and demonstrated its capacity to fabricate structures in nylon with sub-millimeter features and overhanging regions. Subsequently, we demonstrated fabrication of polycaprolactone (PCL) into macroporous structures such as a diamond lattice. Widespread interest in using PCL for bone tissue engineering suggests that PCL lattices are relevant model scaffold geometries for engineering bone. SLS of materials with large powder grain size (~500 μm) leads to part surfaces with high roughness, so we further introduced a simple vapor-smoothing technique to reduce the surface roughness of sintered PCL structures which further improves their elastic modulus and yield stress. Vapor-smoothed PCL can also be used for sacrificial templating of perfusable fluidic networks within orthogonal materials such as poly(dimethylsiloxane) silicone. Finally, we demonstrated that human mesenchymal stem cells were able to adhere, survive, and differentiate down an osteogenic lineage on sintered and smoothed PCL surfaces, suggesting that OpenSLS has the potential to produce PCL scaffolds useful for cell studies. OpenSLS provides the scientific community with an accessible platform for the study of laser sintering and the fabrication of complex geometries in diverse materials. PMID:26841023

Photo-induced green synthesis and antimicrobial efficacy of poly (ɛ-caprolactone)/curcumin/grape leaf extract-silver hybrid nanoparticles.

PubMed

El-Sherbiny, Ibrahim M; El-Shibiny, Ayman; Salih, Ehab

2016-07-01

This study reports the photo-induced green synthesis and antimicrobial assessment of poly(ɛ-caprolactone)/curcumin/grape leaf extract-Ag hybrid nanoparticles (PCL/Cur/GLE-Ag NPs). PCL/Cur/GLE NPs were synthesized via emulsion-solvent evaporation in the presence of PVA as a capping agent, then used as active nano-supports for the green synthesis and stabilization of AgNPs on their surfaces. Both Cur and GLE were selected and incorporated into the PCL nano-supports due to their reported promising antimicrobial activity that would further enhance that of the synthesized AgNPs. The developed PCL/Cur/GLE NPs and PCL/Cur/GLE-Ag hybrid NPs were characterized using UV-visible spectrophotometry, high resolution transmission electron microscopy (HRTEM) and X-ray diffraction (XRD). HRTEM images showed that the PCL/Cur/GLE NPs are monodispersed and spherical with size of about 270nm, and the AgNPs were formed mainly on their surfaces with average size in the range 10-30nm. The synthesized AgNPs were found to be crystalline as shown by XRD patterns with fcc phase oriented along the (111), (200), (220) and (311) planes. The antimicrobial characteristics of the newly developed NPs were investigated against gram-positive and gram-negative bacteria in addition to two fungal strains. The results demonstrated that the PCL/Cur/GLE-Ag hybrid NPs have a potential antimicrobial activity against pathogenic bacterial species and could be considered as an alternative antibacterial agent. Copyright © 2016 Elsevier B.V. All rights reserved.

Branched Crystalline Patterns of Poly(ε-caprolactone) and Poly(4-hydroxystyrene) Blends Thin Films.

PubMed

Hou, Chunyue; Yang, Tianbo; Sun, Xiaoli; Ren, Zhongjie; Li, Huihui; Yan, Shouke

2016-01-14

The chain organization of poly(ε-caprolactone) (PCL) in its blend with poly(4-hydroxystyrene) (PVPh) in thin films (130 ± 10 nm) has been revealed by grazing incident infrared (GIIR) spectroscopy. It can be found that PCL chains orient preferentially in the surface-normal direction and crystallization occurs simultaneously. The morphology of the PCL/PVPh blends films can be identified by optical microscopy (OM). When crystallized at 35 °C, the blends film shows a seaweed-like structure and becomes more open with increasing PVPh content. In contrast, when crystallized at higher temperatures, i.e., 40 and 45 °C, dendrites with apparent crystallographically favored branches can be observed. This characteristic morphology indicates that the diffusion-limited aggregation (DLA) process controls the crystal growth in the blends films. The detailed lamellar structure can be revealed by the height images of atomic force microscopy (AFM), i.e., the crystalline branches are composed of overlayered flat-on lamellae. The branch width has been found to be dependent on the supercooling and PVPh content. This result differs greatly from pure PCL, in which case the crystal patterns controlled by DLA process developed in ultrathin film or monolayers of several nanometers. In the PCL/PVPh blends case, the strong intermolecular interactions and the dilution effect of PVPh should contribute to these results. That is to say, the mobility of PCL chains can be retarded and diffusion of them to the crystal growth front slows down greatly, even though the film thickness is far more than the lamellar thickness of PCL.

Open-Source Selective Laser Sintering (OpenSLS) of Nylon and Biocompatible Polycaprolactone.

PubMed

Kinstlinger, Ian S; Bastian, Andreas; Paulsen, Samantha J; Hwang, Daniel H; Ta, Anderson H; Yalacki, David R; Schmidt, Tim; Miller, Jordan S

2016-01-01

Selective Laser Sintering (SLS) is an additive manufacturing process that uses a laser to fuse powdered starting materials into solid 3D structures. Despite the potential for fabrication of complex, high-resolution structures with SLS using diverse starting materials (including biomaterials), prohibitive costs of commercial SLS systems have hindered the wide adoption of this technology in the scientific community. Here, we developed a low-cost, open-source SLS system (OpenSLS) and demonstrated its capacity to fabricate structures in nylon with sub-millimeter features and overhanging regions. Subsequently, we demonstrated fabrication of polycaprolactone (PCL) into macroporous structures such as a diamond lattice. Widespread interest in using PCL for bone tissue engineering suggests that PCL lattices are relevant model scaffold geometries for engineering bone. SLS of materials with large powder grain size (~500 μm) leads to part surfaces with high roughness, so we further introduced a simple vapor-smoothing technique to reduce the surface roughness of sintered PCL structures which further improves their elastic modulus and yield stress. Vapor-smoothed PCL can also be used for sacrificial templating of perfusable fluidic networks within orthogonal materials such as poly(dimethylsiloxane) silicone. Finally, we demonstrated that human mesenchymal stem cells were able to adhere, survive, and differentiate down an osteogenic lineage on sintered and smoothed PCL surfaces, suggesting that OpenSLS has the potential to produce PCL scaffolds useful for cell studies. OpenSLS provides the scientific community with an accessible platform for the study of laser sintering and the fabrication of complex geometries in diverse materials.

Rupture of posterior cruciate ligament leads to radial displacement of the medial meniscus.

PubMed

Zhang, Can; Deng, Zhenhan; Luo, Wei; Xiao, Wenfeng; Hu, Yihe; Liao, Zhan; Li, Kanghua; He, Hongbo

2017-07-11

To explore the association between the rupture of posterior cruciate ligament (PCL) and the radial displacement of medial meniscus under the conditions of different flexion and various axial loads. The radial displacement value of medial meniscus was measured for the specimens of normal adult knee joints, including 12 intact PCLs, 6 ruptures of the anterolateral bundle (ALB), 6 ruptures of the postmedial bundle (PMB), and 12 complete ruptures. The measurement was conducted at 0°, 30°, 60°, and 90° of knee flexion angles under 200 N, 400 N, 600 N, 800 N and 1000 N of axial loads respectively. The displacement values of medial meniscus of the ALB rupture group increased at 0° flexion under 800 N and 1000 N, and at 30°, 60° and 90° flexion under all loads in comparison with the PCL intact group. The displacement values of the PMB rupture group was higher at 0° and 90° flexion under all loads, and at 30° and 60° flexion under 800 N and 1000 N loads. The displacement of the PCL complete rupture group increased at all flexion angles under all loads. Either partial or complete rupture of the PCL can increase in the radial displacement of the medial meniscus, which may explain the degenerative changes that occuring in the medial meniscus due to PCL injury. Therefore, early reestablishment of the PCL is necessarily required in order to maintain stability of the knee joint after PCL injury.

Complete vs partial-thickness tears of the posterior cruciate ligament: MR findings.

PubMed

Patten, R M; Richardson, M L; Zink-Brody, G; Rolfe, B A

1994-01-01

We sought to define the MRI appearance of both complete and partial-thickness tears of the posterior cruciate ligament (PCL) and to describe patterns of injury and associated MRI findings. Three radiologists retrospectively reviewed MR images and medical records on 32 patients with PCL tears (15 complete, 17 partial) and correlated MRI findings to results of clinical testing and surgery. The PCL had indistinct margins in 27 (84%) of 32 patients and was abnormally thick in 25 (78%) patients. In 31 (97%) patients, the torn PCL showed increased signal intensity on both T1- and T2-weighted pulse sequences. Although there was no statistically significant difference between patients with complete tears and those with partial tears with regard to thickness, margination, and signal intensity of the PCL, MR images in patients with complete tears were more likely to show focal areas of ligamentous discontinuity (10 of 15 cases) (p = 0.01). Associated knee injuries were seen in 21 (66%) patients and were seen more frequently in patients with complete PCL tears (p = 0.015). Bony injury (n = 11, 34%) and tears of the medial collateral ligament (n = 13, 41%) and menisci (n = 10, 31%) were common. No specific pattern of bony injury was found. Posterior cruciate ligament tears can be diagnosed readily by multiplanar MRI using both morphological and signal intensity characteristics. Although differentiation between complete and partial-thickness PCL tears by MRI criteria alone is more problematic, complete tears are more likely to show focal areas of discontinuity and partial tears are more likely to show at least some intact fibers.

The triple PCL sign: bucket handle tears of both medial and lateral menisci in a chronically ACL-deficient knee.

PubMed

Kakel, Rafid; Russell, Robert; VanHeerden, Pieter

2010-10-11

Bucket handle tears of both menisci in the setting of acute or chronic anterior cruciate ligament (ACL) tears of the same knee have rarely been reported in the literature. This article presents a case of a bucket handle tear affecting both the medial and lateral menisci in a patient with chronic ACL rupture. Both bucket handle tears were displaced and locked in the intercondylar notch. A new magnetic resonance image (MRI) sign suggested on sagittal view is called the triple PCL sign, comprising the intact posterior cruciate ligament (PCL) and the 2 displaced fragments in the intercondylar notch from the two bucket handle tears. The precise diagnosis of this condition is of obvious importance for optimal operative planning. While finding the displaced fragment from the medial meniscus is expected to cause the double PCL sign, the torn ACL may have made it easier to visualize the bucket handle tear of the lateral meniscus in the same sagittal plane as the PCL. Only 5 other reports mention bimeniscal bucket handle tears of both the medial and lateral menisci in association with an ACL tear. None have shown the suggested triple PCL sign because of lack of overlap between the 2 bucket handle tears in the coronal plane while lying in the intercondylar notch causing them not to fall in the same sagittal plane. Our patient showed some overlap between the 2 meniscal fragments while lying in the notch to create the triple PCL sign on sagittal MRI. Copyright 2010, SLACK Incorporated.

A new method of fabricating a blend scaffold using an indirect three-dimensional printing technique.

PubMed

Jung, Jin Woo; Lee, Hyungseok; Hong, Jung Min; Park, Jeong Hun; Shim, Jung Hee; Choi, Tae Hyun; Cho, Dong-Woo

2015-11-03

Due to its simplicity and effectiveness, the physical blending of polymers is considered to be a practical strategy for developing a versatile scaffold having desirable mechanical and biochemical properties. In the present work, an indirect three-dimensional (i3D) printing technique was proposed to fabricate a 3D free-form scaffold using a blend of immiscible materials, such as polycaprolactone (PCL) and gelatin. The i3D printing technique includes 3D printing of a mold and a sacrificial molding process. PCL/chloroform and gelatin/water were physically mixed to prepare the blend solution, which was subsequently injected into the cavity of a 3D printed mold. After solvent removal and gelatin cross-linking, the mold was dissolved to obtain a PCL-gelatin (PG) scaffold, with a specific 3D structure. Scanning electron microscopy and Fourier transform infrared spectroscopy analysis indicated that PCL masses and gelatin fibers in the PG scaffold homogenously coexisted without chemical bonding. Compression tests confirmed that gelatin incorporation into the PCL enhanced its mechanical flexibility and softness, to the point of being suitable for soft-tissue engineering, as opposed to pure PCL. Human adipose-derived stem cells, cultured on a PG scaffold, exhibited enhanced in vitro chondrogenic differentiation and tissue formation, compared with those on a PCL scaffold. The i3D printing technique can be used to blend a variety of materials, facilitating 3D scaffold fabrication for specific tissue regeneration. Furthermore, this convenient and versatile technique may lead to wider application of 3D printing in tissue engineering.

Highly roughened polycaprolactone surfaces using oxygen plasma-etching and in vitro mineralization for bone tissue regeneration: fabrication, characterization, and cellular activities.

PubMed

Kim, YongBok; Kim, GeunHyung

2015-01-01

Herein, poly(ɛ-caprolactone) (PCL) surfaces were treated to form various roughness values (R(a)=290-445 nm) and polar functional groups on the surfaces using a plasma-etching process, followed by immersion into simulated body fluid (SBF) for apatite formation. The surface morphology, chemical composition, and mean roughness of the plasma-etched PCL surfaces were measured, and various physical and morphological properties (water contact angles, protein absorption ability, and crystallite size of the apatite layer) of the in vitro mineralized PCL surfaces were evaluated. The roughened PCL surface P-3, which was treated with a sufficient plasma exposure time (4 h), achieved homogeneously distributed apatite formation after soaking in SBF for 7 days, as compared with other surfaces that were untreated or plasma-treated for 30 min or 2 h. Furthermore, to demonstrate their feasibility as a biomimetic surface, pre-osteoblast cells (MC3T3-E1) were cultured on the mineralized PCL surfaces, and cell viability, DAPI-phalloidin fluorescence assay, and alizarin red-staining of the P-3 surface were highly improved compared to the P-1 surface treated with a 30-min plasma exposure time; compared to untreated mineralized PCL surface (N-P), P-3 showed even greater improvements in cell viability and DAPI-phalloidin fluorescence assay. Based on these results, we found that the mineralized PCL surface supplemented with the appropriate plasma treatment can be implicitly helpful to achieve rapid hard tissue regeneration. Copyright © 2014 Elsevier B.V. All rights reserved.

Pharmacokinetics and in vivo delivery of curcumin by copolymeric mPEG-PCL micelles.

PubMed

Kheiri Manjili, Hamidreza; Ghasemi, Parisa; Malvandi, Hojjat; Mousavi, Mir Sajjad; Attari, Elahe; Danafar, Hossein

2017-07-01

Curcumin (CUR) has been associated with anti-inflammatory, antimicrobial, antioxidant, anti-amyloid, and antitumor effects, but its application is limited because of its low aqueous solubility and poor oral bioavailability. To progress the bioavailability and water solubility of CUR, we synthesized five series of mono methoxy poly (ethylene glycol)-poly (ε-caprolactone) (mPEG-PCL) diblock copolymers. The structure of the copolymers was characterized by H NMR, FTIR, DSC and GPC techniques. In this study, CUR was encapsulated within micelles through a single-step nano-precipitation method, leading to formation of CUR-loaded mPEG-PCL (CUR/mPEG-PCL) micelles. The resulting micelles were characterized further by various techniques such as dynamic light scattering (DLS) and atomic force microscopy (AFM). The cytotoxicity of void CUR, mPEG-PCL and CUR/mPEG-PCL micelles was compared to each other by performing MTT assay of the treated MCF-7 and 4T1 cell line. Study of the in vivo pharmacokinetics of the CUR-loaded micelles was also carried out on selected copolymers in comparison with CUR solution formulations. The results showed that the zeta potential of CUR-loaded micelles was about -11.5mV and the average size was 81.0nm. CUR was encapsulated into mPEG-PCL micelles with loading capacity of 20.65±0.015% and entrapment efficiency of 89.32±0.34%. The plasma AUC (0-t), t 1/2 and C max of CUR micelles were increased by 52.8, 4.63 and 7.51-fold compared to the CUR solution, respectively. In vivo results showed that multiple injections of CUR-loaded micelles could prolong the circulation time and increase the therapeutic efficacy of CUR. These results suggested that mPEG-PCL micelles would be a potential carrier for CUR. Copyright © 2016 Elsevier B.V. All rights reserved.

Liposomal quercetin potentiates maxi-K channel openings in smooth muscles and restores its activity after oxidative stress.

PubMed

Melnyk, Mariia I; Dryn, Dariia O; Al Kury, Lina T; Zholos, Alexander V; Soloviev, Anatoly I

2018-04-19

The effects of quercetin-loaded liposomes (PCL-Q) and their constituents, that is, free quercetin (Q) and 'empty' phosphatidylcholine vesicles (PCL), on maxi-K channel activity were studied in single mouse ileal myocytes before and after H 2 O 2 -induced oxidative stress. Macroscopic Maxi-K channel currents were recorded using whole-cell patch clamp techniques, while single BK Ca channel currents were recorded in the cell-attached configuration. Bath application of PCL-Q (100 μg/ml of lipid and 3 μg/ml of quercetin) increased single Maxi-K channel activity more than threefold, from 0.010 ± 0.003 to 0.034 ± 0.004 (n = 5; p < 0.05), whereas single-channel conductance increased non-significantly from 138 to 146 pS. In the presence of PCL-Q multiple simultaneous channel openings were observed, with up to eight active channels in the membrane patch. Surprisingly, 'empty' PCL (100 μg/ml) also produced some channel activation, although it was less potent compared to PCL-Q, that is, these increased NPo from 0.010 ± 0.003 to 0.019 ± 0.003 (n = 5; p < 0.05) and did not affect single-channel conductance (139 pS). Application of PCL-Q restored macroscopic Maxi-K currents suppressed by H 2 O 2 -induced oxidative stress in ileal smooth muscle cells. We conclude that PCL-Q can activate Maxi-K channels in ileal myocytes mainly by increasing channel open probability, as well as maintain Maxi-K-mediated whole-cell current under the conditions of oxidative stress. While fusion of the 'pure' liposomes with the plasma membrane may indirectly activate Maxi-K channels by altering channel's phospholipids environment, the additional potentiating action of quercetin may be due to its better bioavailability.

Atmospheric Pressure Plasma Jet Treatment of Poly-ε-caprolactone Polymer Solutions To Improve Electrospinning.

PubMed

Grande, Silvia; Van Guyse, Joachim; Nikiforov, Anton Y; Onyshchenko, Iuliia; Asadian, Mahtab; Morent, Rino; Hoogenboom, Richard; De Geyter, Nathalie

2017-09-27

An atmospheric pressure plasma jet (APPJ) specifically designed for liquid treatment has been used in this work to improve the electrospinnability of a 5 w/v % solution of poly-ε-caprolactone (PCL) in a mixture of chloroform and N,N-dimethylformamide. Untreated PCL solutions were found to result in nonuniform fibers containing a large number of beads, whereas plasma-treated solutions (exposure time of 2-5 min) enabled the generation of beadless, uniform nanofibers with an average diameter of 450 nm. This enhanced electrospinnability was found to be mainly due to the highly increased conductivity of the plasma-modified PCL solutions. Consequently, more stretching of the polymer jet occurred during electrospinning, leading to the generation of bead-free fibers. Plasma treatment also results in an increased viscosity and decreased pH values. To explain these observed changes, optical emission spectroscopy (OES) has been used to examine the excited species present in the APPJ in contact with the PCL solution. This study revealed that the peaks attributed to H, CH, CH 2 , and C 2 species could be responsible for the degradation of solvent molecules and/or PCL structures during the plasma treatment. Size exclusion chromatography and X-ray photoelectron spectroscopy results showed that the molecular weight and the chemical composition of PCL were not significantly affected by the APPJ treatment. Plasma exposure mainly results in the degradation of the solvent molecules instead of modifying the PCL macromolecules, preserving the original polymer as much as possible. A hypothesis for the observed macroscopic changes in viscosity and pH values could be the generation of new chemical species such as HCl and/or HNO 3 . These species are characterized by their high conductivity, low pH values, and strong polarity and could enhance the solvent quality for PCL, leading to the expansion of the polymer coil, which could in turn explain the observed enhanced viscosity after plasma modification.

Recidivism in female offenders: PCL-R lifestyle factor and VRAG show predictive validity in a German sample.

PubMed

Eisenbarth, Hedwig; Osterheider, Michael; Nedopil, Norbert; Stadtland, Cornelis

2012-01-01

A clear and structured approach to evidence-based and gender-specific risk assessment of violence in female offenders is high on political and mental health agendas. However, most data on the factors involved in risk-assessment instruments are based on data of male offenders. The aim of the present study was to validate the use of the Psychopathy Checklist Revised (PCL-R), the HCR-20 and the Violence Risk Appraisal Guide (VRAG) for the prediction of recidivism in German female offenders. This study is part of the Munich Prognosis Project (MPP). It focuses on a subsample of female delinquents (n = 80) who had been referred for forensic-psychiatric evaluation prior to sentencing. The mean time at risk was 8 years (SD = 5 years; range: 1-18 years). During this time, 31% (n = 25) of the female offenders were reconvicted, 5% (n = 4) for violent and 26% (n = 21) for non-violent re-offenses. The predictive validity of the PCL-R for general recidivism was calculated. Analysis with receiver-operating characteristics revealed that the PCL-R total score, the PCL-R antisocial lifestyle factor, the PCL-R lifestyle factor and the PCL-R impulsive and irresponsible behavioral style factor had a moderate predictive validity for general recidivism (area under the curve, AUC = 0.66, p = 0.02). The VRAG has also demonstrated predictive validity (AUC = 0.72, p = 0.02), whereas the HCR-20 showed no predictive validity. These results appear to provide the first evidence that the PCL-R total score and the antisocial lifestyle factor are predictive for general female recidivism, as has been shown consistently for male recidivists. The implications of these findings for crime prevention, prognosis in women, and future research are discussed. Copyright © 2012 John Wiley & Sons, Ltd.

Polymer-Ceramic Spiral Structured Scaffolds for Bone Tissue Engineering: Effect of Hydroxyapatite Composition on Human Fetal Osteoblasts

PubMed Central

Zhang, Xiaojun; Chang, Wei; Lee, Paul; Wang, Yuhao; Yang, Min; Li, Jun; Kumbar, Sangamesh G.; Yu, Xiaojun

2014-01-01

For successful bone tissue engineering, a scaffold needs to be osteoconductive, porous, and biodegradable, thus able to support attachment and proliferation of bone cells and guide bone formation. Recently, hydroxyapatites (HA), a major inorganic component of natural bone, and biodegrade polymers have drawn much attention as bone scaffolds. The present study was designed to investigate whether the bone regenerative properties of nano-HA/polycaprolactone (PCL) spiral scaffolds are augmented in an HA dose dependent manner, thereby establishing a suitable composition as a bone formation material. Nano-HA/PCL spiral scaffolds were prepared with different weight ratios of HA and PCL, while porosity was introduced by a modified salt leaching technique. Human fetal osteoblasts (hFOBs) were cultured on the nano-HA/PCL spiral scaffolds up to 14 days. Cellular responses in terms of cell adhesion, viability, proliferation, differentiation, and the expression of bone-related genes were investigated. These scaffolds supported hFOBs adhesion, viability and proliferation. Cell proliferation trend was quite similar on polymer-ceramic and neat polymer spiral scaffolds on days 1, 7, and 14. However, the significantly increased amount of alkaline phosphatase (ALP) activity and mineralized matrix synthesis was evident on the nano-HA/PCL spiral scaffolds. The HA composition in the scaffolds showed a significant effect on ALP and mineralization. Bone phenotypic markers such as bone sialoprotein (BSP), osteonectin (ON), osteocalcin (OC), and type I collagen (Col-1) were semi-quantitatively estimated by reverse transcriptase polymerase chain reaction analysis. All of these results suggested the osteoconductive characteristics of HA/PCL nanocomposite and cell maturation were HA dose dependent. For instance, HA∶PCL = 1∶4 group showed significantly higher ALP mineralization and elevated levels of BSP, ON, OC and Col-I expression as compared other lower or higher ceramic ratios. Amongst the different nano-HA/PCL spiral scaffolds, the 1∶4 weight ratio of HA and PCL is shown to be the most optimal composition for bone tissue regeneration. PMID:24475056

[Return to sport after surgical treatment of a posterior cruciate ligament injury : A retrospective study of 60 patients].

PubMed

Ahrend, M; Ateschrang, A; Döbele, S; Stöckle, U; Grünwald, L; Schröter, S; Ihle, C

2016-12-01

Injuries of the posterior cruciate ligament (PCL) lead to an initial reduction of sporting activity. However, in previous studies, return to sport after operative treatment of PCL injuries has been analysed insufficiently. The aim of this study was (1) to determine the rate of return to sport in physically active patients, (2) to analyse possible changes in sporting activities and (3) to examine the influence of the severity of the initial injury. Within a retrospective clinical and radiological follow-up at least 24 months after surgery (80.3 ± 28.2 months), 60 patients (44.8 ± 12.1 years) with surgically treated isolated or combined PCL injuries were included in the study. Pre-accidental and post-operative sporting activities were queried and compared in a standardised questionnaire. Possible differences with respect to the initial injury severity (Cooper classification) were examined. The return-to-sport rate of the physically active patients was 87.0 %. 17.6 % of patients with a combined PCL injury and 4.8 % of patients with isolated PCL injury were not able to return to sport. Significant reductions in the frequency of exercise (p = 0.0087), the duration of exercise (p = 0.0003) and the amount of regularly performed sports (p < 0.0001) were found. A change from high-impact sports to low-impact sports was noted. Patients with operatively treated PCL injuries can return to sport. However, for competitive athletes an injury to the PCL can lead to the end of their career. A reduction of sporting activities and a change from high-impact sports to low-impact sports can be expected. A persisting inability to return to sporting activities in patients with isolated PCL injuries cannot be assumed.

The relationship between cavum septum pellucidum and psychopathic traits in a large forensic sample.

PubMed

Crooks, Dana; Anderson, Nathaniel E; Widdows, Matthew; Petseva, Nia; Koenigs, Michael; Pluto, Charles; Kiehl, Kent A

2018-04-01

Cavum septum pellucidum (CSP) is a neuroanatomical variant of the septum pellucidum that is considered a marker for disrupted brain development. Several small sample studies have reported CSP to be related to disruptive behavior, persistent antisocial traits, and even psychopathy. However, no large-scale samples have comprehensively examined the relationship between CSP, psychopathic traits, and antisocial behavior in forensic samples. Here we test hypotheses about the presence of CSP and its relationship to psychopathic traits in incarcerated males (N = 1432). We also examined the incidence of CSP in two non-incarcerated male control samples for comparison (N = 208 and 125). Ethnic and racial composition was varied with a mean age of 33.1, and an average IQ of 96.96. CSP was evaluated via structural magnetic resonance imaging. CSP was measured by length (number of 1.0 mm slices) in continuous analyses, and classified as absent (0) or present (1+ mm), as well as by size (absent (0), small (1-3), medium (4-5), or large (6+ mm)) for comparison with prior work. The Wechsler Adult Intelligence Scale (WAIS-III), Structured Clinical Interview (SCID-I/P), and Hare Psychopathy Checklist-Revised (PCL-R) were used to assess IQ, substance dependence, and psychopathy, respectively. CSP length was positively associated with PCL-R total, Factor 1 (interpersonal/affective) and Facets 1 (interpersonal) and 2 (affective). CSP was no more prevalent among inmates than among non-incarcerated controls, with similar distributions of size. These results support the hypotheses that abnormal septal/limbic development may contribute to dimensional affective/interpersonal traits of psychopathy, but CSP is not closely associated with antisocial behavior, per se. Published by Elsevier Ltd.

Strontium eluting graphene hybrid nanoparticles augment osteogenesis in a 3D tissue scaffold

NASA Astrophysics Data System (ADS)

Kumar, Sachin; Chatterjee, Kaushik

2015-01-01

The objective of this work was to prepare hybrid nanoparticles of graphene sheets decorated with strontium metallic nanoparticles and demonstrate their advantages in bone tissue engineering. Strontium-decorated reduced graphene oxide (RGO_Sr) hybrid nanoparticles were synthesized by the facile reduction of graphene oxide and strontium nitrate. X-ray diffraction, transmission electron microscopy, and atomic force microscopy revealed that the hybrid particles were composed of RGO sheets decorated with 200-300 nm metallic strontium particles. Thermal gravimetric analysis further confirmed the composition of the hybrid particles as 22 wt% of strontium. Macroporous tissue scaffolds were prepared by incorporating RGO_Sr particles in poly(ε-caprolactone) (PCL). The PCL/RGO_Sr scaffolds were found to elute strontium ions in aqueous medium. Osteoblast proliferation and differentiation was significantly higher in the PCL scaffolds containing the RGO_Sr particles in contrast to neat PCL and PCL/RGO scaffolds. The increased biological activity can be attributed to the release of strontium ions from the hybrid nanoparticles. This study demonstrates that composites prepared using hybrid nanoparticles that elute strontium ions can be used to prepare multifunctional scaffolds with good mechanical and osteoinductive properties. These findings have important implications for designing the next generation of biomaterials for use in tissue regeneration.The objective of this work was to prepare hybrid nanoparticles of graphene sheets decorated with strontium metallic nanoparticles and demonstrate their advantages in bone tissue engineering. Strontium-decorated reduced graphene oxide (RGO_Sr) hybrid nanoparticles were synthesized by the facile reduction of graphene oxide and strontium nitrate. X-ray diffraction, transmission electron microscopy, and atomic force microscopy revealed that the hybrid particles were composed of RGO sheets decorated with 200-300 nm metallic strontium particles. Thermal gravimetric analysis further confirmed the composition of the hybrid particles as 22 wt% of strontium. Macroporous tissue scaffolds were prepared by incorporating RGO_Sr particles in poly(ε-caprolactone) (PCL). The PCL/RGO_Sr scaffolds were found to elute strontium ions in aqueous medium. Osteoblast proliferation and differentiation was significantly higher in the PCL scaffolds containing the RGO_Sr particles in contrast to neat PCL and PCL/RGO scaffolds. The increased biological activity can be attributed to the release of strontium ions from the hybrid nanoparticles. This study demonstrates that composites prepared using hybrid nanoparticles that elute strontium ions can be used to prepare multifunctional scaffolds with good mechanical and osteoinductive properties. These findings have important implications for designing the next generation of biomaterials for use in tissue regeneration. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr05060f

Importance of tibial slope for stability of the posterior cruciate ligament deficient knee.

PubMed

Giffin, J Robert; Stabile, Kathryne J; Zantop, Thore; Vogrin, Tracy M; Woo, Savio L-Y; Harner, Christopher D

2007-09-01

Previous studies have shown that increasing tibial slope can shift the resting position of the tibia anteriorly. As a result, sagittal osteotomies that alter slope have recently been proposed for treatment of posterior cruciate ligament (PCL) injuries. Increasing tibial slope with an osteotomy shifts the resting position anteriorly in a PCL-deficient knee, thereby partially reducing the posterior tibial "sag" associated with PCL injury. This shift in resting position from the increased slope causes a decrease in posterior tibial translation compared with the PCL-deficient knee in response to posterior tibial and axial compressive loads. Controlled laboratory study. Three knee conditions were tested with a robotic universal force-moment sensor testing system: intact, PCL-deficient, and PCL-deficient with increased tibial slope. Tibial slope was increased via a 5-mm anterior opening wedge osteotomy. Three external loading conditions were applied to each knee condition at 0 degrees, 30 degrees, 60 degrees, 90 degrees, and 120 degrees of knee flexion: (1) 134-N anterior-posterior (A-P) tibial load, (2) 200-N axial compressive load, and (3) combined 134-N A-P and 200-N axial loads. For each loading condition, kinematics of the intact knee were recorded for the remaining 5 degrees of freedom (ie, A-P, medial-lateral, and proximal-distal translations, internal-external and varus-valgus rotations). Posterior cruciate ligament deficiency resulted in a posterior shift of the tibial resting position to 8.4 +/- 2.6 mm at 90 degrees compared with the intact knee. After osteotomy, tibial slope increased from 9.2 degrees +/- 1.0 degrees in the intact knee to 13.8 degrees +/- 0.9 degrees. This increase in slope reduced the posterior sag of the PCL-deficient knee, shifting the resting position anteriorly to 4.0 +/- 2.0 mm at 90 degrees. Under a 200-N axial compressive load with the osteotomy, an additional increase in anterior tibial translation to 2.7 +/- 1.7 mm at 30 degrees was observed. Under a 134-N A-P load, the osteotomy did not significantly affect total A-P translation when compared with the PCL-deficient knee. However, because of the anterior shift in resting position, there was a relative decrease in posterior tibial translation and increase in anterior tibial translation. Increasing tibial slope in a PCL-deficient knee reduces tibial sag by shifting the resting position of the tibia anteriorly. This sag is even further reduced when the knee is subjected to axial compressive loads. These data suggest that increasing tibial slope may be beneficial for patients with PCL-deficient knees.

Ready to Use Tissue Construct for Military Bone & Cartilage Trauma

DTIC Science & Technology

2013-10-01

scaffolds composed of 90% poly-caprolactone (PCL) and 10% hydroxyapatite (HA) by weight (PCL+HA) without any seeding with either canine MSC or biologic...ligaments of the 5 knee. The implant consisted of a two layer Polycarprolacton (PCL) mixed with 10% hydroxyapatite (HA) scaffold with a 500 μm top...denoted by arrows, are apparent on both tibiae. Ratios of the biomechanical test parameters (experimental/control) in terms of percentage for

Score Metric Equivalence of the Psychopathy Checklist-Revised (PCL-R) across Criminal Offenders in North America and the United Kingdom. A Critique of Cooke, Michie, Hart, and Clark (2005) and New Analyses

ERIC Educational Resources Information Center

Bolt, Daniel M.; Hare, Robert D.; Neumann, Craig S.

2007-01-01

David Cooke and colleagues have published a series of item response theory (IRT) studies investigating the equivalence of the Psychopathy Checklist-Revised (PCL-R) for European versus North American (NA) male criminal offenders. They have consistently concluded that PCL-R scores are not equivalent, with European offenders receiving scores up to…

High-surface Thermally Stable Mesoporous Gallium Phosphates Constituted by Nanoparticles as Primary Building Blocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

V Parvulescu; V Parvulescu; D Ciuparu

In constant, search for micro/mesoporous materials, gallium phosphates, have attracted continued interest due to the large pore size reported for some of these solids in comparison with analogous aluminum phosphates. However up to now, the porosity of gallium phosphates collapsed upon template removal or exposure to the ambient moisture. In the present work, we describe high-surface thermally stable mesoporous gallium phosphates synthesized from gallium propoxide and PCl{sub 3} and different templating agents such as amines (dipropylamine, piperidine and aminopiperidine) and quaternary ammonium salts (C{sub 16}H{sub 33}(CH{sub 3})3NBr and C{sub 16}PyCl). These highly reactive precursors have so far not been usedmore » as gallium and phosphate sources for the synthesis of gallophosphates. Conceptually, our present synthetic procedure is based on the fast formation of gallium phosphate nanoparticles via the reaction of gallium propoxide with PCl{sub 3} and subsequent construction of the porous material with nanoparticles as building blocks. The organization of the gallophosphate nanoparticles in stable porous structures is effected by the templates. Different experimental procedures varying the molar composition of the sol-gel, pH and the pretreatment of gallium precursor were assayed, most of them leading to satisfactory materials in terms of thermal stability and porosity. In this way, a series of gallium phosphates with surface are above 200 m{sup 2} g{sup -1}, and narrow pore size from 3 to 6 nm and remarkable thermal stability (up to 550 C) have been prepared. In some cases, the structure tends to show some periodicity and regularity as determined by XRD. The remarkable stability has allowed us to test the catalytic activity of gallophosphates for the aerobic oxidation of alkylaromatics with notable good results. Our report reopens the interest for gallophosphates in heterogeneous catalysis.« less

Surface chemical immobilization of bioactive peptides on synthetic polymers for cardiac tissue engineering.

PubMed

Rosellini, Elisabetta; Cristallini, Caterina; Guerra, Giulio D; Barbani, Niccoletta

2015-01-01

The aim of this work was the development of new synthetic polymeric systems, functionalized by surface chemical modification with bioactive peptides, for myocardial tissue engineering. Polycaprolactone and a poly(ester-ether-ester) block copolymer synthesized in our lab, polycaprolactone-poly(ethylene oxide)-polycaprolactone (PCL-PEO-PCL), were used as the substrates to be modified. Two pentapeptides, H-Gly-Arg-Gly-Asp-Ser-OH (GRGDS) from fibronectin and H-Tyr-Ile-Gly-Ser-Arg-OH (YIGSR) from laminin, were used for the functionalization. Polymeric membranes were obtained by casting from solutions and then functionalized by means of alkaline hydrolysis and subsequent coupling of the bioactive molecules through 1-(3-dimethylaminopropyl)-3-ethylcarbodimide hydrochloride/N-hydroxysuccinimide chemistry. The hydrolysis conditions, in terms of hydrolysis time, temperature, and sodium hydroxide concentration, were optimized for the two materials. The occurrence of the coupling reaction was demonstrated by infrared spectroscopy, as the presence on the functionalized materials of the absorption peaks typical of the two peptides. The peptide surface density was determined by chromatographic analysis and the distribution was studied by infrared chemical imaging. The results showed a nearly homogeneous peptide distribution, with a density above the minimum value necessary to promote cell adhesion. Preliminary in vitro cell culture studies demonstrated that the introduction of the bioactive molecules had a positive effect on improving C2C12 myoblasts growth on the synthetic materials.

Multifunctional Self-Adhesive Fibrous Layered Matrix (FiLM) for Tissue Glues and Therapeutic Carriers.

PubMed

Yoon, Ye-Eun; Im, Byung Gee; Kim, Jung-Suk; Jang, Jae-Hyung

2017-01-09

Tissue adhesives, which inherently serve as wound sealants or as hemostatic agents, can be further augmented to acquire crucial functions as scaffolds, thereby accelerating wound healing or elevating the efficacy of tissue regeneration. Herein, multifunctional adherent fibrous matrices, acting as self-adhesive scaffolds capable of cell/gene delivery, were devised by coaxially electrospinning poly(caprolactone) (PCL) and poly(vinylpyrrolidone) (PVP). Wrapping the building block PCL fibers with the adherent PVP layers formed film-like fibrous matrices that could rapidly adhere to wet biological surfaces, referred to as fibrous layered matrix (FiLM) adhesives. The inclusion of ionic salts (i.e., dopamine hydrochloride) in the sheath layers generated spontaneously multilayered fibrous adhesives, whose partial layers could be manually peeled off, termed derivative FiLM (d-FiLM). In the context of scaffolds/tissue adhesives, both FiLM and d-FiLM demonstrated almost identical characteristics (i.e., sticky, mechanical, and performances as cell/gene carriers). Importantly, the single FiLM-process can yield multiple sets of d-FiLM by investing the same processing time, materials, and labor required to form a single conventional adhesive fibrous mat, thereby highlighting the economic aspects of the process. The FiLM/d-FiLM offer highly impacting contributions to many biomedical applications, especially in fields that require urgent aids (e.g., endoscopic surgeries, implantation in wet environments, severe wounds).

Manganese ferrite nanoparticle micellar nanocomposites as MRI contrast agent for liver imaging.

PubMed

Lu, Jian; Ma, Shuli; Sun, Jiayu; Xia, Chunchao; Liu, Chen; Wang, Zhiyong; Zhao, Xuna; Gao, Fabao; Gong, Qiyong; Song, Bin; Shuai, Xintao; Ai, Hua; Gu, Zhongwei

2009-05-01

Iron oxide nanoparticles are effective contrast agents for enhancement of magnetic resonance imaging at tissue, cellular or even molecular levels. In this study, manganese doped superparamagnetic iron oxide (Mn-SPIO) nanoparticles were used to form ultrasensitive MRI contrast agents for liver imaging. Hydrophobic Mn-SPIO nanoparticles are synthesized in organic phase and then transferred into water with the help of block copolymer mPEG-b-PCL. These Mn-SPIO nanoparticles are self-assembled into small clusters (mean diameter approximately 80nm) inside micelles as revealed by transmission electron microscopy. Mn-SPIO nanoparticles inside micelles decrease PCL crystallization temperatures, as verified from differential scanning calorimetry and Fourier transform infrared spectroscopy. The Mn-SPIO based nanocomposites are superparamagnetic at room temperature. At the magnetic field of 1.5T, Mn-SPIO nanoparticle clustering micelles have a T(2) relaxivity of 270 (Mn+Fe)mM(-1)s(-1), which is much higher than single Mn-SPIO nanoparticle containing lipid-PEG micelles. This clustered nanocomposite has brought significant liver contrast with signal intensity changes of -80% at 5min after intravenous administration. The time window for enhanced-MRI can last about 36h with obvious contrast on liver images. This sensitive MRI contrast agent may find applications in identification of small liver lesions, evaluation of the degree of liver cirrhosis, and differential diagnosis of other liver diseases.

Magnetic nanoparticle-loaded electrospun polymeric nanofibers for tissue engineering.

PubMed

Zhang, Heng; Xia, JiYi; Pang, XianLun; Zhao, Ming; Wang, BiQiong; Yang, LingLin; Wan, HaiSu; Wu, JingBo; Fu, ShaoZhi

2017-04-01

Magnetic nanoparticles have been one of the most attractive nanomaterials for various biomedical applications including magnetic resonance imaging (MRI), diagnostic contrast enhancement, magnetic cell separation, and targeted drug delivery. Three-dimensional (3-D) fibrous scaffolds have broad application prospects in the biomedical field, such as drug delivery and tissue engineering. In this work, a novel three-dimensional composite membrane composed of the tri-block copolymer poly(ε-caprolactone)-poly(ethylene glycol)-poly(ε-caprolactone) (PCL-PEG-PCL, PCEC) and magnetic iron oxide nanoparticles (Fe 3 O 4 NPs) were fabricated using electrospinning technology. The physico-chemical properties of the PCEC/Fe 3 O 4 membranes were investigated by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and differential scanning calorimetry (DSC). Morphological observation using scanning electron microscopy (SEM) showed that the composite fibers containing 5% Fe 3 O 4 nanoparticles had a diameter of 250nm. In vitro cell culture of NIH 3T3 cells on the PCEC/Fe 3 O 4 membranes showed that the PCEC/Fe 3 O 4 fibers might be a suitable scaffold for cell adhesion. Moreover, MTT analysis also demonstrated that the membranes possessed lower cytotoxicity. Therefore, this study revealed that the magnetic PCEC/Fe 3 O 4 fibers might have great potential for using in skin tissue engineering. Copyright © 2016 Elsevier B.V. All rights reserved.

Micellar Self-Assembly of Recombinant Resilin-/Elastin-Like Block Copolypeptides.

PubMed

Weitzhandler, Isaac; Dzuricky, Michael; Hoffmann, Ingo; Garcia Quiroz, Felipe; Gradzielski, Michael; Chilkoti, Ashutosh

2017-08-14

Reported here is the synthesis of perfectly sequence defined, monodisperse diblock copolypeptides of hydrophilic elastin-like and hydrophobic resilin-like polypeptide blocks and characterization of their self-assembly as a function of structural parameters by light scattering, cryo-TEM, and small-angle neutron scattering. A subset of these diblock copolypeptides exhibit lower critical solution temperature and upper critical solution temperature phase behavior and self-assemble into spherical or cylindrical micelles. Their morphologies are dictated by their chain length, degree of hydrophilicity, and hydrophilic weight fraction of the ELP block. We find that (1) independent of the length of the corona-forming ELP block there is a minimum threshold in the length of the RLP block below which self-assembly does not occur, but that once that threshold is crossed, (2) the RLP block length is a unique molecular parameter to independently tune self-assembly and (3) increasing the hydrophobicity of the corona-forming ELP drives a transition from spherical to cylindrical morphology. Unlike the self-assembly of purely ELP-based block copolymers, the self-assembly of RLP-ELPs can be understood by simple principles of polymer physics relating hydrophilic weight fraction and polymer-polymer and polymer-solvent interactions to micellar morphology, which is important as it provides a route for the de novo design of desired nanoscale morphologies from first principles.

Evaluation of the potential of novel PCL-PPDX biodegradable scaffolds as support materials for cartilage tissue engineering.

PubMed

Chaim, Isaac A; Sabino, Marcos A; Mendt, Mayela; Müller, Alejandro J; Ajami, Diana

2012-04-01

Cartilage is a specialized tissue represented by a group of particular cells (the chondrocytes) and an abundant extracellular matrix. Because of the reduced regenerative capacity of this tissue, cartilage injuries are often difficult to handle. Nowadays tissue engineering has emerged as a very promising discipline, and biodegradable polymeric scaffolds are widely used as tissue supports. In cartilage injuries, the use of autologous chondrocyte implantation from non-affected cartilage zones has emerged as a very interesting technique, where chondrocytes are expanded in order to obtain a greater number of cells. Nevertheless, it has been reported that chondrocytes in bidimensional cultures suffer a dedifferentiation process. The present study sought, in the first place, to standardize a novel protocol in order to obtain primary cultures of chondrocytes from newborn rabbit hyaline cartilage from the xiphoid process. Second, the potential of porous three-dimensional (3D) biodegradable polymeric matrices as support materials for chondrocytes was evaluated: a novel poly(ε-caprolactone)-poly(p-dioxanone) (PCL-PPDX) blend in a 90:10 w:w ratio and poly(ε-caprolactone) (PCL). After achieving the standardization, a typical round-shaped chondrocyte morphology and the expression of collagen type II and aggrecan, evaluated by RT-PCR, were observed. Second-passage chondrocytes adhered effectively to these scaffolds, although cell growth at 7 days in culture was significantly less in the PCL-PPDX blend. After 3 weeks of culture on PCL-PPDX or PCL, the cells expressed collagen type II. The present study demonstrates the potential, unknown until now, of PCL-PPDX blend scaffolds in the field of cartilage tissue engineering. Copyright © 2011 John Wiley & Sons, Ltd.

Electrospun PLA: PCL composites embedded with unmodified and 3-aminopropyltriethoxysilane (ASP) modified halloysite nanotubes (HNT)

NASA Astrophysics Data System (ADS)

Haroosh, Hazim J.; Dong, Yu; Chaudhary, Deeptangshu S.; Ingram, Gordon D.; Yusa, Shin-ichi

2013-02-01

Electrospinning is a simple and versatile fiber synthesis technique in which a high-voltage electric field is applied to a stream of polymer melt or polymer solution, resulting in the formation of continuous micro/nanofibers. Halloysite nanotubes (HNT) have been found to achieve improved structural and mechanical properties when embedded into various polymer matrices. This research work focuses on blending poly( ɛ-caprolactone) (PCL) (9 and 15 wt%/v) and poly(lactic acid) (PLA) (fixed at 8 wt%/v) solutions with HNT at two different concentrations 1 and 2 wt%/v. Both unmodified HNT and HNT modified with 3-aminopropyltriethoxysilane (ASP) were utilized in this study. Fiber properties have been shown to be strongly related to the solution viscosity and electrical conductivity. The addition of HNT increased the solution viscosity, thus resulting in the production of uniform fibers. For both PCL concentrations, the average fiber diameter increased with the increasing of HNT concentration. The average fiber diameters with HNT-ASP were reduced considerably in comparison to those with unmodified HNT when using 15 wt%/v PCL. Slightly better dispersion was obtained for PLA: PCL composites embedded with HNT-ASP compared to unmodified HNT. Furthermore, the addition of HNT-ASP to the polymeric blends resulted in a moderate decrease in the degree of crystallinity, as well as slight reductions of glass transition temperature of PCL, the crystallization temperature and melting temperature of PLA within composite materials. The infrared spectra of composites confirmed the successful embedding of HNT-ASP into PLA: PCL nanofibers relative to unmodified HNT due to the premodification using ASP to reduce the agglomeration behavior. This study provides a new material system that could be potentially used in drug delivery, and may facilitate good control of the drug release process.

Perfluorocarbon-perfused 23 gauge three-dimensional vitrectomy for complicated diabetic tractional retinal detachment

PubMed Central

Velez-Montoya, Raul; Guerrero-Naranjo, Jose Luis; Garcia-Aguirre, Gerardo; Morales-Cantón, Virgilio; Fromow-Guerra, Jans; Quiroz-Mercado, Hugo

2011-01-01

Background Perfluorocarbon liquid (PCL)-perfused vitrectomy has been shown in previous studies to be feasible, safe, and to have advantages in managing complicated cases of tractional retinal detachment. The present study had the objectives of describing the anatomical results and measuring surgical time and PCL consumption when combining PCL-perfused techniques with modern vitrectomy equipment. Methods A prospective, interventional consecutive case series was investigated. We enrolled patients with diabetic tractional retinal detachment, complicated by proliferative vitreoretinopathy and poor vision. A 23 gauge PCL-perfused vitrectomy was done with three-dimensional settings. During the procedure, we assessed the degree of surgical bleeding, visualization quality, and difficulty of membrane dissections. Visual acuity, intraocular pressure, and anatomical success were assessed at one and 3 months of follow-up. Results Twelve patients were enrolled in this study. There were no statistical significant changes in intraocular pressure and visual acuity throughout the follow-up period. Surgery was performed in a hemorrhage-free environment in almost all cases, with good visualization and low technical difficulty. The mean complete surgical time was 94.92 ± 25.03 minutes. The mean effective vitrectomy time was 22.50 ± 19.04 minutes and the mean PCL consumption was 25.08 ± 9.76 mL, with a speed of 1.11 mL/minute. Anatomical success was 67% at 3 months. Conclusion Although the technique proved to have some advantages in managing complicated cases of diabetic tractional retinal detachment, there was a high consumption of PCL. A redesign of the entire system is needed in order to decrease the amount of PCL needed for the technique. PMID:22267907

Temperament traits and psychopathy in a group of patients with antisocial personality disorder.

PubMed

Basoglu, Cengiz; Oner, Ozgur; Ates, Alpay; Algul, Ayhan; Bez, Yasin; Ebrinc, Servet; Cetin, Mesut

2011-01-01

The Psychopathy Checklist Revised (PCL-R) and Temperament and Character Inventory (TCI) have been used extensively in research of personality disorders; however, no previous study has investigated the relation between psychopathy factors and temperament and character traits in patients with antisocial personality disorder (ASPD). Our aim was to fill this gap in the literature. The PCL-R Factor scores and the TCI temperament and character scores were evaluated in 68 men with ASPD and 65 healthy male controls. The ASPD cases had significantly higher PCL-R Factor 1, Factor 2, and Total scores, as well as significantly higher TCI Novelty Seeking and Harm Avoidance scores, whereas the control group had higher TCI Reward Dependence, Persistence, Self-Directedness, and Cooperativeness scores. Correlation analysis revealed that, in the whole study group, PCL-R Factor 1, Factor 2, and Total scores were positively correlated with Novelty Seeking and Harm Avoidance scores and negatively correlated with Reward Dependence, Persistence, Self-Directedness, and Cooperativeness scores. When each group was analyzed separately, the correlations were not significant. Regression analysis supported the main findings. Our results showed that both PCL-R Factor 1 score, which is claimed to reflect "core psychopathy," and PCL-R Factor 2 score, which reflects criminal behaviors, were positively correlated with Novelty Seeking and Harm Avoidance and were negatively correlated with Reward Dependence in the whole sample. The reduced variance of PCL-R in each group might lead to nonsignificant associations within groups. Without the subjects with severe psychopathy in the present study, it might not be possible to show the association. Copyright © 2011 Elsevier Inc. All rights reserved.

Magnetically responsive polycaprolactone nanoparticles for progesterone screening in biological and environmental samples using gas chromatography.

PubMed

Es'haghi, Zarrin; Nezhadali, Azizollah; Khatibi, Aram-Dokht

2016-08-01

A new Fe3O4/poly(є-caprolactone) (PCL) magnetite nanocomposite was fabricated and used as a sorbent for magnetically mediated PCL microspheres solid-phase extraction (MM-PCL-SPE) followed by gas chromatography-flame ionization detection (GC-FID) for monitoring of progesterone (PGN) hormone in biological and environmental matrices, namely blood serum, tap water, urine, and hospital wastewater. The nanomagnetite core of the sorbent was synthesized by a co-precipitation method. Magnetic nanoparticles (MNPs) were then microencapsulated with PCL microspheres using emulsion polymerization. The nanocomposite was characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The magnetite sorbent can be effectively dispersed in aqueous solution and attracted to an external magnetic field. The MM-PCL-SPE process for PGN assay involved (a) dispersion of the sorbent in the donor phase aqueous solution with sonication, (b) exposure to a magnetic field to collect sorbent that had adsorbed the analyte, and (c) solvent desorption of extracted PGN for GC-FID analysis. The work demonstrates the usefulness of MM-PCL-SPE in the rapid and sensitive monitoring of trace amounts of PGN in real samples. The limit of detection (LOD) and limit of quantification (LOQ) were 1.00 and 3.30 ng/mL, respectively. The relative recoveries in real samples were adequate. Linearity was observed over a wide range of 2.2-10,000.0 ng/mL in aqueous media and urine and 0.01-70.0 μg/mL in blood serum. Graphical Abstract In this research new Fe3O4/poly(є-caprolactone) (PCL) magnetite microspheres were developed as an efficient sorbent for solid-phase extraction of progesterone hormone in biological and environmental matrices.

Evaluation of 3D printed PCL/PLGA/β-TCP versus collagen membranes for guided bone regeneration in a beagle implant model.

PubMed

Won, J-Y; Park, C-Y; Bae, J-H; Ahn, G; Kim, C; Lim, D-H; Cho, D-W; Yun, W-S; Shim, J-H; Huh, J-B

2016-10-07

Here, we compared 3D-printed polycaprolactone/poly(lactic-co-glycolic acid)/β-tricalcium phosphate (PCL/PLGA/β-TCP) membranes with the widely used collagen membranes for guided bone regeneration (GBR) in beagle implant models. For mechanical property comparison in dry and wet conditions and cytocompatibility determination, we analyzed the rate and pattern of cell proliferation of seeded fibroblasts and preosteoblasts using the cell counting kit-8 assay and scanning electron microscopy. Osteogenic differentiation was verified using alizarin red S staining. At 8 weeks following implantation in vivo using beagle dogs, computed tomography and histological analyses were performed after sacrifice. Cell proliferation rates in vitro indicated that early cell attachment was higher in collagen than in PCL/PLGA/β-TCP membranes; however, the difference subsided by day 7. Similar outcomes were found for osteogenic differentiation, with approximately 2.5 times greater staining in collagen than PCL/PLGA/β-TCP, but without significant difference by day 14. In vivo, bone regeneration in the defect area, represented by new bone formation and bone-to-implant contact, paralleled those associated with collagen membranes. However, tensile testing revealed that whereas the PCL/PLGA/β-TCP membrane mechanical properties were conserved in both wet and dry states, the tensile property of collagen was reduced by 99% under wet conditions. Our results demonstrate in vitro and in vivo that PCL/PLGA/β-TCP membranes have similar levels of biocompatibility and bone regeneration as collagen membranes. In particular, considering that GBR is always applied to a wet environment (e.g. blood, saliva), we demonstrated that PCL/PLGA/β-TCP membranes maintained their form more reliably than collagen membranes in a wet setting, confirming their appropriateness as a GBR membrane.

Novel poly(ε-caprolactone)/gelatin wound dressings prepared by emulsion electrospinning with controlled release capacity of Ketoprofen anti-inflammatory drug.

PubMed

Basar, A O; Castro, S; Torres-Giner, S; Lagaron, J M; Turkoglu Sasmazel, H

2017-12-01

In the present study, a single and binary Ketoprofen-loaded mats of ultrathin fibers were developed by electrospinning and their physical properties and drug release capacity was analyzed. The single mat was prepared by solution electrospinning of poly(ε-caprolactone) (PCL) with Ketoprofen at a weight ratio of 5wt%. This Ketoprofen-containing PCL solution was also used as the oil phase in a 7:3 (wt/wt) emulsion with gelatin dissolved in acidified water. The resultant stable oil-in-water (O/W) emulsion of PCL-in-gelatin, also containing Ketoprofen at 5wt%, was electrospun to produce the binary mat. Cross-linking process was performed by means of glutaraldehyde vapor on the electrospun binary mat to prevent dissolution of the hydrophilic gelatin phase. The performed characterization indicated that Ketoprofen was successfully embedded in the single and binary electrospun mats, i.e. PCL and PCL/gelatin, and both mats showed high hydrophobicity but poor thermal resistance. In vitro release studies interestingly revealed that, in comparison to the single PCL electrospun mat, the binary PCL/gelatin mat significantly hindered Ketoprofen burst release and exhibited a sustained release capacity of the drug for up to 4days. In addition, the electrospun Ketoprofen-loaded mats showed enhanced attachment and proliferation of L929 mouse fibroblast cells, presenting the binary mat the highest cell growth yield due to its improved porosity. The here-developed electrospun materials clearly show a great deal of potential as novel wound dressings with an outstanding controlled capacity to release drugs. Copyright © 2017 Elsevier B.V. All rights reserved.

Novel self-assembled amphiphilic poly(epsilon-caprolactone)-grafted-poly(vinyl alcohol) nanoparticles: hydrophobic and hydrophilic drugs carrier nanoparticles.

PubMed

Sheikh, Faheem A; Barakat, Nasser A M; Kanjwal, Muzafar A; Aryal, Santosh; Khil, Myung Seob; Kim, Hak-Yong

2009-03-01

In the present study, we have aimed to produce nanoparticles (NPs) possessing the capability of carrying both of the hydrophobic and hydrophilic drugs and reveal significant release for both drug types. Poly(epsilon-caprolactone) (PCL) grafted poly(vinyl alcohol) (PVA) copolymer (PCL-g-PVA) has been prepared and shaped in nano-particulate form to be adequate for carrying the drugs. Stannous octoate (Sn(II)Oct(2)) was used to catalyze PVA and epsilon-caprolactone monomer to chemically bond. Moreover, this catalyst enhanced side chain polymerization reaction for the utilized epsilon-caprolactone monomer to form poly(epsilon-caprolactone) (PCL). The formed PCL was attached as branches with PVA backbone. (1)H NMR has confirmed formation of PCL and grafting of PVA by this new polymer. Moreover, the vibration modes in the functional groups of PCL-g-PVA have been detected by FT-IR. The thermal alteration in the grafted polymer was checked by TGA analysis. The successfully synthesized grafted copolymer was able to self-aggregate into NPs by direct dialysis method. The size, morphology and charges associated with the obtained NPs were analyzed by DLS, TEM and ELS, respectively. PCL-g-PVA NPs were investigated as drug carrier models for hydrophobic and hydrophilic anti cancer drugs; paclitaxel and doxorubicin. In vitro drug release experiments were conducted; the loaded NPs reveal continuous and sustained release form for both drugs, up to 20 and 15 days for paclitaxel and doxorubicin, respectively. However, in a case of using pure drugs only, both drugs completely released within 1-2 h. The overall obtained results strongly recommend the use these novel NPs in future drug delivery systems.

Fabrication and characterization of poly-(ε)-caprolactone and bioactive glass composites for tissue engineering applications.

PubMed

Mohammadkhah, Ali; Marquardt, Laura M; Sakiyama-Elbert, Shelly E; Day, Delbert E; Harkins, Amy B

2015-04-01

Much work has focused on developing synthetic materials that have tailored degradation profiles and physical properties that may prove useful in developing biomaterials for tissue engineering applications. In the present study, three different composite sheets consisting of biodegradable poly-ε-caprolactone (PCL) and varying types of bioactive glass were investigated. The three composites were composed of 50wt.% PCL and (1) 50wt.% 13-93 B3 borate glass particles, (2) 50wt.% 45S5 silicate glass particles, or (3) a blend of 25wt.% 13-93 B3 and 25wt.% 45S5 glass particles. Degradation profiles determined for each composite showed the composite that contained only 13-93 B3 borate glass had a higher degradation rate compared to the composite containing only 45S5 silicate glass. Uniaxial tensile tests were performed on the composites to determine the effect of adding glass to the polymer on mechanical properties. The peak stress of all of the composites was lower than that of PCL alone, but 100% PCL had a higher stiffness when pre-reacted in cell media for 6weeks, whereas composite sheets did not. Finally, to determine whether the composite sheets would maintain neuronal growth, dorsal root ganglia isolated from embryonic chicks were cultured on composite sheets, and neurite outgrowth was measured. The bioactive glass particles added to the composites showed no negative effects on neurite extension, and neurite extension increased on PCL:45S5 PCL:13-93 B3 when pre-reacted in media for 24h. This work shows that composite sheets of PCL and bioactive glass particles provide a flexible biomaterial for neural tissue engineering applications. Copyright © 2015 Elsevier B.V. All rights reserved.

Surface phase separation, dewetting feature size, and crystal morphology in thin films of polystyrene/poly(ε-caprolactone) blend.

PubMed

Ma, Meng; He, Zhoukun; Li, Yuhan; Chen, Feng; Wang, Ke; Zhang, Qing; Deng, Hua; Fu, Qiang

2012-12-01

Thin films of polystyrene (PS)/poly(ε-caprolactone) (PCL) blends were prepared by spin-coating and characterized by tapping mode force microscopy (AFM). Effects of the relative concentration of PS in polymer solution on the surface phase separation and dewetting feature size of the blend films were systematically studied. Due to the coupling of phase separation, dewetting, and crystallization of the blend films with the evaporation of solvent during spin-coating, different size of PS islands decorated with various PCL crystal structures including spherulite-like, flat-on individual lamellae, and flat-on dendritic crystal were obtained in the blend films by changing the film composition. The average distance of PS islands was shown to increase with the relative concentration of PS in casting solution. For a given ratio of PS/PCL, the feature size of PS appeared to increase linearly with the square of PS concentration while the PCL concentration only determined the crystal morphology of the blend films with no influence on the upper PS domain features. This is explained in terms of vertical phase separation and spinodal dewetting of the PS rich layer from the underlying PCL rich layer, leading to the upper PS dewetting process and the underlying PCL crystalline process to be mutually independent. Copyright © 2012 Elsevier Inc. All rights reserved.

Electrospun PCL/gelatin composite nanofiber structures for effective guided bone regeneration membranes.

PubMed

Ren, Ke; Wang, Yi; Sun, Tao; Yue, Wen; Zhang, Hongyu

2017-09-01

Guided bone regeneration (GBR) membranes have been proved of great benefit for bone tissue engineering due to the improvement of cell attachment and proliferation. To develop GBR membranes with better biocompatibility and more proper degradation ability, here we fabricated polycaprolactone (PCL, polymer)/gelatin (protein) hybrid nanofibrous GBR membranes via electrospinning, followed by crosslinking with genipin. Acetic acid (HAc) was utilized to resolve the phase separation of PCL and gelatin, therefore homogeneous PCL/gelatin hybrid nanofibers with different ratios were successfully prepared. FTIR, XPS, TGA, DSC results proved that the proportion of PCL and gelatin in the as-spun nanofiber membranes could be simply adjusted by changing the weight ratio of PCL and gelatin in the spinning solution. SEM and AFM images demonstrated that all the nanofibers possessed uniform and smooth structures both in two dimension (2D) and three dimension (3D). The mechanical tests showed that these nanofibers exhibited appropriate tensile and strength properties, which were suitable for bone tissue engineering. CCK-8 and SEM images revealed that all the membranes were biocompatible to MC3T3-e1 cells. In addition, the in vitro osteogenesis characterizations, alizarin red in normal medium and osteogenesis medium, indicated that the nanofibers could promote bone formation. Therefore, all these results could suggest that our design of electrospun polymer/protein nanofiber membranes was effective for guided bone regeneration. Copyright © 2017. Published by Elsevier B.V.

Corrosion behavior and mechanical properties of bioactive sol-gel coatings on titanium implants.

PubMed

Catauro, M; Bollino, F; Papale, F; Giovanardi, R; Veronesi, P

2014-10-01

Organic-inorganic hybrid coatings based on zirconia and poly (ε-caprolactone) (PCL) were prepared by means of sol-gel dip-coating technique and used to coat titanium grade 4 implants (Ti-4) in order to improve their wear and corrosion resistance. The coating chemical composition has been analysed by ATR-FTIR. The influence of the PCL amount has been investigated on the microstructure, mechanical properties of the coatings and their ability to inhibit the corrosion of titanium. SEM analysis has shown that all coatings have a nanostructured nature and that the films with high PCL content are crack-free. Mechanical properties of the coatings have been studied using scratch and nano-indentation tests. The results have shown that the Young's modulus of the coatings decreases in presence of large amounts of the organic phase, and that PCL content affects also the adhesion of the coatings to the underlying Ti-4 substrate. However, the presence of cracks on the PCL-free coatings affects severely the mechanical response of the samples at high loads. The electrochemical behavior and corrosion resistance of the coated and uncoated substrate has been investigated by polarization tests. The results have shown that both the coatings with or without PCL don't affect significantly the already excellent passivation properties of titanium. Copyright © 2014. Published by Elsevier B.V.

Comparative Study of the Physical, Topographical and Biological Properties of Electrospinning PCL, PLLA, their Blend and Copolymer Scaffolds

NASA Astrophysics Data System (ADS)

Bolbasov, E.; Goreninskii, S.; Tverdokhlebov, S.; Mishanin, A.; Viknianshchuk, A.; Bezuidenhout, D.; Golovkin, A.

2018-05-01

Biodegradable polymers (blends, copolymers) could be the ideal materials for manufacturing of scaffolds for small diameter vascular graft. Such material characteristics as mechanical properties, chemical structure, nano- and micro topography, surface charge, porosity, wettability etc. are becoming the most important aspects for effectiveness of prosthesis biofunctionalization because of their great impact on cell adhesion, spreading, cell proliferation, differentiation and cell function. The aim of the study is to compare physical, topographical and biological properties of polycaprolactone (PCL), poly-L-lactic acid (PLLA), polycaprolactone + poly-L-lactic acid blend (PCL PLLA), L-lactide/Caprolactone copolymer (PLC7015) scaffolds fabricated with the same fiber thickness using electrospun technology. PCL PLLA scaffolds had the highest average pore area (p<0.01) and the lowest strength (p<0.01). PLC7015 scaffolds had the significantly lower average pore area (p=0.03) but the highest elastic deformation (p<0.01). Biological testing with MMSC (multipotent mesenchyme stem cells) demonstrated that after 72 hours of co-cultivation only on PCL and PLLA scaffolds cells entered to the active phase of adhesion process. We propose that physical and topographical properties of PCL, PLLA, their blend and copolymer are of a great dependence of chemical structure but could be changed during the manufacturing process that will lead to changes in biological properties.

Poly(ε-caprolactone)/nano fluoridated hydroxyapatite scaffolds for bone tissue engineering: in vitro degradation and biocompatibility study.

PubMed

Johari, N; Fathi, M H; Golozar, M A; Erfani, E; Samadikuchaksaraei, A

2012-03-01

In this study, biodegradation and biocompatibility of novel poly(ε-caparolactone)/nano fluoridated hydroxyapatite (PCL-FHA) scaffolds were investigated. The FHA nanopowders were prepared via mechanical alloying method and had a chemical composition of Ca(10)(PO(4))(6)OH(2-x )F(x) (where x values were selected equal to 0.5 and 2.0). In order to fabricate PCL-FHA scaffolds, 10, 20, 30 and 40 wt% of the FHA were added to the PCL. The PCL-FHA scaffolds were produced by the solvent casting/particulate leaching using sodium chloride particles (with diameters of 300-500 μm) as the porogen. The phase structure, microstructure and morphology of the scaffolds were evaluated using X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy techniques. Porosity of the scaffolds was measured using the Archimedes' Principle. In vitro degradation of PCL-FHA scaffolds was studied by incubating the samples in phosphate buffered saline at 37°C and pH 7.4 for 30 days. Moreover, biocompatibility was evaluated by MTT assay after seeding and culture of osteoblast-like cells on the scaffolds. Results showed that the osteoblast-like cells attached to and proliferated on PCL-FHA and increasing the porosity of the scaffolds increased the cell viability. Also, degradation rate of scaffolds were increased with increasing the fluorine content in scaffolds composition.

G-CSF loaded nanofiber/nanoparticle composite coated with collagen promotes wound healing in vivo.

PubMed

Tanha, Shima; Rafiee-Tehrani, Morteza; Abdollahi, Mohamad; Vakilian, Saeid; Esmaili, Zahra; Naraghi, Zahra Safaei; Seyedjafari, Ehsan; Javar, Hamid Akbari

2017-10-01

Sustained release of functional growth factors can be considered as a beneficial methodology for wound healing. In this study, recombinant human granulocyte colony-stimulating factor (G-CSF)-loaded chitosan nanoparticles were incorporated in Poly(ε-caprolactone) (PCL) nanofibers, followed by surface coating with collagen type I. Physical and mechanical properties of the PCL nanofibers containing G-CSF loaded chitosan nanoparticles PCL/NP(G-CSF) and in vivo performance for wound healing were investigated. G-CSF structural stability was evaluated through SDS_PAGE, reversed phase (RP) HPLC and size-exclusion chromatography, as well as circular dichroism. Nanofiber/nanoparticle composite scaffold was demonstrated to have appropriate mechanical properties as a wound dresser and a sustained release of functional G-CSF. The PCL/NP(G-CSF) scaffold showed a suitable proliferation and well-adherent morphology of stem cells. In vivo study and histopathological evaluation outcome revealed that skin regeneration was dramatically accelerated under PCL/NP(G-CSF) as compared with control groups. Superior fibroblast maturation, enhanced collagen deposition and minimum inflammatory cells were also the beneficial properties of PCL/NP(G-CSF) over the commercial dressing. The synergistic effect of extracellular matrix-mimicking nanofibrous membrane and G-CSF could develop a suitable supportive substrate in order to extensive utilization for the healing of skin wounds. © 2017 Wiley Periodicals Inc. J Biomed Mater Res Part A: 105A: 2830-2842, 2017. © 2017 Wiley Periodicals, Inc.

Performance characteristics of the PTSD Checklist in retired firefighters exposed to the World Trade Center disaster.

PubMed

Chiu, Sydney; Webber, Mayris P; Zeig-Owens, Rachel; Gustave, Jackson; Lee, Roy; Kelly, Kerry J; Rizzotto, Linda; McWilliams, Rita; Schorr, John K; North, Carol S; Prezant, David J

2011-05-01

Since the World Trade Center (WTC) attacks on September 11, 2001, the Fire Department, City of New York Monitoring Program has provided physical and mental health screening services to rescue/recovery workers. This study evaluated performance of the self-report PTSD Checklist (PCL) as a screening tool for risk of posttraumatic stress disorder (PTSD) in firefighters who worked at Ground Zero, compared with the interviewer-administered Diagnostic Interview Schedule (DIS). From December 2005 to July 2007, all retired firefighter enrollees completed the PCL and DIS on the same day. Sensitivity, specificity, receiver operating characteristic (ROC) curves, and Youden index (J) were used to assess properties of the PCL and to identify an optimum cutoff score. Six percent of 1,915 retired male firefighters were diagnosed with PTSD using the DIS to assess DSM-IV criteria. Depending on the PCL cutoff, the prevalence of elevated risk relative to DSM-IV criteria varied from 16% to 22%. Youden index identified an optimal cutoff score of 39, in contrast with the frequently recommended cutoff of 44. At 39, PCL sensitivity was 0.85, specificity was 0.82, and the area under the ROC curve was 0.91 relative to DIS PTSD diagnosis. This is the first study to validate the PCL in retired firefighters and determine the optimal cutoff score to maximize opportunities for PTSD diagnosis and treatment.

Evaluation of 3D-Printed Polycaprolactone Scaffolds Coated with Freeze-Dried Platelet-Rich Plasma for Bone Regeneration.

PubMed

Li, Junda; Chen, Meilin; Wei, Xiaoying; Hao, Yishan; Wang, Jinming

2017-07-19

Three-dimensional printing is one of the most promising techniques for the manufacturing of scaffolds for bone tissue engineering. However, a pure scaffold is limited by its biological properties. Platelet-rich plasma (PRP) has been shown to have the potential to improve the osteogenic effect. In this study, we improved the biological properties of scaffolds by coating 3D-printed polycaprolactone (PCL) scaffolds with freeze-dried and traditionally prepared PRP, and we evaluated these scaffolds through in vitro and in vivo experiments. In vitro, we evaluated the interaction between dental pulp stem cells (DPSCs) and the scaffolds by measuring cell proliferation, alkaline phosphatase (ALP) activity, and osteogenic differentiation. The results showed that freeze-dried PRP significantly enhanced ALP activity and the mRNA expression levels of osteogenic genes (ALP, RUNX2 (runt-related gene-2), OCN (osteocalcin), OPN (osteopontin)) of DPSCs ( p < 0.05). In vivo, 5 mm calvarial defects were created, and the PRP-PCL scaffolds were implanted. The data showed that compared with traditional PRP-PCL scaffolds or bare PCL scaffolds, the freeze-dried PRP-PCL scaffolds induced significantly greater bone formation ( p < 0.05). All these data suggest that coating 3D-printed PCL scaffolds with freeze-dried PRP can promote greater osteogenic differentiation of DPSCs and induce more bone formation, which may have great potential in future clinical applications.

Ternary composite scaffolds with tailorable degradation rate and highly improved colonization by human bone marrow stromal cells.

PubMed

Idaszek, J; Bruinink, A; Święszkowski, W

2015-07-01

Poly(ε-caprolactone), PCL, is of great interest for fabrication of biodegradable scaffolds due to its high compatibility with various manufacturing techniques, especially Fused Deposition Modeling (FDM). However, slow degradation and low strength make application of PCL limited only to longer-term bioresorbable and non-load bearing implants. To overcome latter drawbacks, ternary PCL-based composite fibrous scaffolds consisting of 70-95 wt % PCL, 5 wt % Tricalcium Phosphate (TCP) and 0-25 wt % poly(lactide-co-glycolide) (PLGA) were fabricated using FDM. In the present study, the effect of composition of the scaffolds on their mechanical properties, degradation kinetics, and surface properties (wettability, surface energy, and roughness) was investigated and correlated with response of human bone marrow mesenchymal stromal cells (HBMC). The presence of PLGA increased degradation kinetics, surface roughness and significantly improved scaffold colonization. Of the evaluated surface properties only the wettability was correlated with the surface area colonized by HBMC. This study demonstrates that introduction of PLGA into PCL-TCP binary composite could largely abolish the disadvantages of the PCL matrix and improve biocompatibility by increasing wettability and polar interactions rather than surface roughness. Additionally, we showed great potential of multicellular spheroids as a sensitive in vitro tool for detection of differences in chemistry of 3D scaffolds. © 2014 Wiley Periodicals, Inc.

Modulatory effects of psychopathy on Wisconsin Card Sorting Test performance in male offenders with Antisocial Personality Disorder.

PubMed

Pera-Guardiola, Vanessa; Batalla, Iolanda; Bosque, Javier; Kosson, David; Pifarré, Josep; Hernández-Ribas, Rosa; Goldberg, Ximena; Contreras-Rodríguez, Oren; Menchón, José M; Soriano-Mas, Carles; Cardoner, Narcís

2016-01-30

Neuropsychological deficits in executive functions (EF) have been linked to antisocial behavior and considered to be cardinal to the onset and persistence of severe antisocial and aggressive behavior. However, when psychopathy is present, prior evidence suggests that the dorsolateral prefrontal cortex is unaffected leading to intact EF. Ninety-one male offenders with Antisocial Personality Disorder (ASPD) and 24 controls completed the Wisconsin Card Sorting Test (WCST). ASPD individuals were grouped in three categories according to Psychopathy Checklist-Revised (PCL-R) scores (low, medium and high). We hypothesized that ASPD offenders with high PCL-R scores will not differ from healthy controls in EF and will show better EF performance in comparison with subjects with low PCL-R scores. Results showed that ASPD offenders with low PCL-R scores committed more perseverative errors and responses than controls and offenders with high PCL-R scores, which did not differ from healthy controls. Moreover, scores on Factor 1 and the interpersonal facet of the PCL-R were predictors of better WCST performance. Our results suggest a modulatory role of psychopathy in the cognitive performance of ASPD offenders, and provide further evidence supporting that offenders with ASPD and psychopathy are characterized by a cognitive profile different from those with ASPD without psychopathy. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Effects of poly (ε-caprolactone) coating on the properties of three-dimensional printed porous structures.

PubMed

Zhou, Zuoxin; Cunningham, Eoin; Lennon, Alex; McCarthy, Helen O; Buchanan, Fraser; Clarke, Susan A; Dunne, Nicholas

2017-06-01

Powder-based inkjet three-dimensional printing (3DP) to fabricate pre-designed 3D structures has drawn increasing attention. However there are intrinsic limitations associated with 3DP technology due to the weak bonding within the printed structure, which significantly compromises its mechanical integrity. In this study, calcium sulphate ceramic structures demonstrating a porous architecture were manufactured using 3DP technology and subsequently post-processed with a poly (ε-caprolactone) (PCL) coating. PCL concentration, immersion time, and number of coating layers were the principal parameters investigated and improvement in compressive properties was the measure of success. Interparticle spacing within the 3DP structures were successfully filled with PCL material. Consequently the compressive properties, wettability, morphology, and in vitro resorption behaviour of 3DP components were significantly augmented. The average compressive strength, Young׳s modulus, and toughness increased 217%, 250%, and 315%, following PCL coating. Addition of a PCL surface coating provided long-term structural support to the host ceramic material, extending the resorption period from less than 7 days to a minimum of 56 days. This study has demonstrated that application of a PCL coating onto a ceramic 3DP structure was a highly effective approach to addressing some of the limitations of 3DP manufacturing and allows this advanced technology to be potentially used in a wider range of applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Polymer powder processing of cryomilled polycaprolactone for solvent-free generation of homogeneous bioactive tissue engineering scaffolds.

PubMed

Lim, Jing; Chong, Mark Seow Khoon; Chan, Jerry Kok Yen; Teoh, Swee-Hin

2014-06-25

Synthetic polymers used in tissue engineering require functionalization with bioactive molecules to elicit specific physiological reactions. These additives must be homogeneously dispersed in order to achieve enhanced composite mechanical performance and uniform cellular response. This work demonstrates the use of a solvent-free powder processing technique to form osteoinductive scaffolds from cryomilled polycaprolactone (PCL) and tricalcium phosphate (TCP). Cryomilling is performed to achieve micrometer-sized distribution of PCL and reduce melt viscosity, thus improving TCP distribution and improving structural integrity. A breakthrough is achieved in the successful fabrication of 70 weight percentage of TCP into a continuous film structure. Following compaction and melting, PCL/TCP composite scaffolds are found to display uniform distribution of TCP throughout the PCL matrix regardless of composition. Homogeneous spatial distribution is also achieved in fabricated 3D scaffolds. When seeded onto powder-processed PCL/TCP films, mesenchymal stem cells are found to undergo robust and uniform osteogenic differentiation, indicating the potential application of this approach to biofunctionalize scaffolds for tissue engineering applications. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Passive coherent location system simulation and evaluation

NASA Astrophysics Data System (ADS)

Slezák, Libor; Kvasnička, Michael; Pelant, Martin; Vávra, Jiř; Plšek, Radek

2006-02-01

Passive Coherent Location (PCL) is going to be important and perspective system of passive location of non cooperative and stealth targets. It works with the sources of irradiation of opportunity. PCL is intended to be a part of mobile Air Command and Control System (ACCS) as a Deployable ACCS Component (DAC). The company ERA works on PCL system parameters verification program by complete PCL simulator development since the year 2003. The Czech DoD takes financial participation on this program. The moving targets scenario, the RCS calculation by method of moment, ground clutter scattering and signal processing method (the bottle neck of the PCL) are available up to now in simulator tool. The digital signal (DSP) processing algorithms are performed both on simulated data and on real data measured at NATO C3 Agency in their Haag experiment. The Institute of Information Theory and Automation of the Academy of Sciences of the Czech Republic takes part on the implementation of the DSP algorithms in FPGA. The paper describes the simulator and signal processing structure and results both on simulated and measured data.

PLASMA CELL LEUKEMIA

PubMed Central

de Larrea, Carlos Fernandez; Kyle, Robert A.; Durie, Brian GM; Ludwig, Heinz; Usmani, Saad; Vesole, David H.; Hajek, Roman; Miguel, Jésus San; Sezer, Orhan; Sonneveld, Pieter; Kumar, Shaji K.; Mahindra, Anuj; Comenzo, Ray; Palumbo, Antonio; Mazumber, Amitabha; Anderson, Kenneth C.; Richardson, Paul G.; Badros, Ashraf Z.; Caers, Jo; Cavo, Michele; LeLeu, Xavier; Dimopoulos, Meletios A.; Chim, CS; Schots, Rik; Noeul, Amara; Fantl, Dorotea; Mellqvist, Ulf-Henrik; Landgren, Ola; Chanan-Khan, Asher; Moreau, Philippe; Fonseca, Rafael; Merlini, Giampaolo; Lahuerta, JJ; Bladé, Joan; Orlowski, Robert Z.; Shah, Jatin J.

2014-01-01

Plasma cell leukemia (PCL) is a rare and aggressive variant of myeloma characterized by the presence of circulating plasma cells. It is classified as either primary PCL occurring at diagnosis or as secondary PCL in patients with relapsed/refractory myeloma. Primary PCL is a distinct clinic-pathologic entity with different cytogenetic and molecular findings. The clinical course is aggressive with short remissions and survival duration. The diagnosis is based upon the percentage (≥ 20%) and absolute number (≥ 2 × 10 9/L) of plasma cells in the peripheral blood. It is proposed that the thresholds for diagnosis be reexamined and consensus recommendations are made for diagnosis, as well as, response and progression criteria. Induction therapy needs to begin promptly and have high clinical activity leading to rapid disease control in an effort to minimize the risk of early death. Intensive chemotherapy regimens and bortezomib-based regimens are recommended followed by high-dose therapy with autologous stem-cell transplantation (HDT/ASCT) if feasible. Allogeneic transplantation can be considered in younger patients. Prospective multicenter studies are required to provide revised definitions and better understanding of the pathogenesis of PCL. PMID:23288300

Human unrestricted somatic stem cells loaded in nanofibrous PCL scaffold and their healing effect on skin defects.

PubMed

Bahrami, Hoda; Keshel, Saeed Heidari; Chari, Aliakbar Jafari; Biazar, Esmaeil

2016-09-01

Unrestricted somatic stem cells (USSCs) loaded in nanofibrous polycaprolactone (PCL) scaffolds can be used for skin regeneration when grafted onto full-thickness skin defects of rats. Nanofibrous PCL scaffolds were designed by the electrospinning method and crosslinked with laminin protein. Afterwards, the scaffolds were evaluated by scanning electron microscopy, and physical and mechanical assays. In this study, nanofibrous PCL scaffolds loaded with USSCs were grafted onto the skin defects. The wounds were subsequently investigated 21 days after grafting. Results of mechanical and physical analyses showed good resilience and compliance to movement as a skin graft. In animal models; study samples exhibited the most pronounced effect on wound closure, with statistically significant improvement in wound healing being seen at 21 days post-operatively. Histological examinations of healed wounds from all samples showed a thin epidermis plus recovered skin appendages in the dermal layer for samples with cell. Thus, the graft of nanofibrous PCL scaffolds loaded with USSC showed better results during the healing process of skin defects in rat models.

Polycomb-like 2 Associates with PRC2 and Regulates Transcriptional Networks during Mouse Embryonic Stem Cell Self-Renewal and Differentiation

PubMed Central

Walker, Emily; Chang, Wing Y.; Hunkapiller, Julie; Cagney, Gerard; Garcha, Kamal; Torchia, Joseph; Krogan, Nevan J.; Reiter, Jeremy F.; Stanford, William L.

2010-01-01

Summary Polycomb group (PcG) proteins are conserved epigenetic transcriptional repressors that control numerous developmental gene expression programs and have recently been implicated in modulating embryonic stem cell (ESC) fate. We identified the PcG protein PCL2 (polycomb-like 2) in a genome-wide screen for regulators of self-renewal and pluripotency and predicted that it would play an important role in mouse ESC fate determination. Using multiple biochemical strategies, we provide evidence that PCL2 is a Polycomb Repressive Complex 2 (PRC2)-associated protein in mouse ESCs. Knockdown of Pcl2 in ESCs resulted in heightened self-renewal characteristics, defects in differentiation and altered patterns of histone methylation. Integration of global gene expression and promoter occupancy analyses allowed us to identify PCL2 and PRC2 transcriptional targets and draft regulatory networks. We describe the role of PCL2 in both modulating transcription of ESC self-renewal genes in undifferentiated ESCs as well as developmental regulators during early commitment and differentiation. PMID:20144788

Hydroxyapatite-doped polycaprolactone nanofiber membrane improves tendon-bone interface healing for anterior cruciate ligament reconstruction.

PubMed

Han, Fei; Zhang, Peng; Sun, Yaying; Lin, Chao; Zhao, Peng; Chen, Jiwu

2015-01-01

Hamstring tendon autograft is a routine graft for anterior cruciate ligament (ACL) reconstruction. However, ways of improving the healing between the tendon and bone is often overlooked in clinical practice. This issue can be addressed by using a biomimetic scaffold. Herein, a biomimetic nanofiber membrane of polycaprolactone/nanohydroxyapatite/collagen (PCL/nHAp/Col) is fabricated that mimics the composition of native bone tissue for promoting tendon-bone healing. This membrane has good cytocompatibility, allowing for osteoblast cell adhesion and growth and bone formation. As a result, MC3T3 cells reveal a higher mineralization level in PCL/nHAp/Col membrane compared with PCL membrane alone. Further in vivo studies in ACL reconstruction in a rabbit model shows that PCL/nHAp/Col-wrapped tendon may afford superior tissue integration to nonwrapped tendon in the interface between the tendon and host bone as well as improved mechanical strength. This study shows that PCL/nHAp/Col nanofiber membrane wrapping of autologous tendon is effective for improving tendon healing with host bone in ACL reconstruction.

Self-assembled poly(ε-caprolactone)-g-chondroitin sulfate copolymers as an intracellular doxorubicin delivery carrier against lung cancer cells

PubMed Central

Lin, Yue-Jin; Liu, Yu-Sheng; Yeh, Hsin-Hwa; Cheng, Tian-Lu; Wang, Li-Fang

2012-01-01

The aim of this study was to utilize self-assembled polycaprolactone (PCL)-grafted chondroitin sulfate (CS) as an anticancer drug carrier. We separately introduced double bonds to the hydrophobic PCL and the hydrophilic CS. The modified PCL was reacted with the modified CS through a radical reaction (CSMA-g-PCL). The copolymer without doxorubicin (DOX) was noncytotoxic in CRL-5802 and NCI-H358 cells at a concentration ranging from 5–1000 μg/mL and DOX-loaded CSMA-g-PCL (Micelle DOX) had the lowest inhibitory concentration of 50% cell growth values against the NCI-H358 cells among test samples. The cellular uptake of Micelle DOX into the cells was confirmed by flow cytometric data and confocal laser scanning microscopic images. The in vivo tumor-targeting efficacy of Micelle DOX was realized using an NCI-H358 xenograft nude mouse model. The mice administered with Micelle DOX showed suppressed growth of the NCI-H358 lung tumor compared with those administered with phosphate-buffered saline and free DOX. PMID:22904627

Diagnostic Utility of the Posttraumatic Stress Disorder (PTSD) Checklist for Identifying Full and Partial PTSD in Active-Duty Military.

PubMed

Dickstein, Benjamin D; Weathers, Frank W; Angkaw, Abigail C; Nievergelt, Caroline M; Yurgil, Kate; Nash, William P; Baker, Dewleen G; Litz, Brett T

2015-06-01

The aim of this study was to determine optimally efficient cutoff scores on the Posttraumatic Stress Disorder Checklist (PCL) for identifying full posttraumatic stress disorder (PTSD) and partial PTSD (P-PTSD) in active-duty Marines and Sailors. Participants were 1,016 Marines and Sailors who were administered the PCL and Clinician-Administered PTSD Scale (CAPS) 3 months after returning from Operations Iraqi and Enduring Freedom. PCL cutoffs were tested against three CAPS-based classifications: full PTSD, stringent P-PTSD, and lenient P-PTSD. A PCL score of 39 was found to be optimally efficient for identifying full PTSD. Scores of 38 and 33 were found to be optimally efficient for identifying stringent and lenient P-PTSD, respectively. Findings suggest that the PCL cutoff that is optimally efficient for detecting PTSD in active-duty Marines and Sailors is substantially lower than the score of 50 commonly used by researchers. In addition, findings provide scores useful for identifying P-PTSD in returning service members. © The Author(s) 2014.

Heart rate variability: Pre-deployment predictor of post-deployment PTSD symptoms

PubMed Central

Pyne, Jeffrey M.; Constans, Joseph I.; Wiederhold, Mark D.; Gibson, Douglas P.; Kimbrell, Timothy; Kramer, Teresa L.; Pitcock, Jeffery A.; Han, Xiaotong; Williams, D. Keith; Chartrand, Don; Gevirtz, Richard N.; Spira, James; Wiederhold, Brenda K.; McCraty, Rollin; McCune, Thomas R.

2017-01-01

Heart rate variability is a physiological measure associated with autonomic nervous system activity. This study hypothesized that lower pre-deployment HRV would be associated with higher post-deployment post-traumatic stress disorder (PTSD) symptoms. Three-hundred-forty-three Army National Guard soldiers enrolled in the Warriors Achieving Resilience (WAR) study were analyzed. The primary outcome was PTSD symptom severity using the PTSD Checklist – Military version (PCL) measured at baseline, 3- and 12-month post-deployment. Heart rate variability predictor variables included: high frequency power (HF) and standard deviation of the normal cardiac inter-beat interval (SDNN). Generalized linear mixed models revealed that the pre-deployment PCL*ln(HF) interaction term was significant (p < 0.0001). Pre-deployment SDNN was not a significant predictor of post-deployment PCL. Covariates included age, pre-deployment PCL, race/ethnicity, marital status, tobacco use, childhood abuse, pre-deployment traumatic brain injury, and previous combat zone deployment. Pre-deployment heart rate variability predicts post-deployment PTSD symptoms in the context of higher pre-deployment PCL scores. PMID:27773678

Synthesis of Diblock copolymer poly-3-hydroxybutyrate -block-poly-3-hydroxyhexanoate [PHB-b-PHHx] by a β-oxidation weakened Pseudomonas putida KT2442.

PubMed

Tripathi, Lakshmi; Wu, Lin-Ping; Chen, Jinchun; Chen, Guo-Qiang

2012-04-05

Block polyhydroxyalkanoates (PHA) were reported to be resistant against polymer aging that negatively affects polymer properties. Recently, more and more attempts have been directed to make PHA block copolymers. Diblock copolymers PHB-b-PHHx consisting of poly-3-hydroxybutyrate (PHB) block covalently bonded with poly-3-hydroxyhexanoate (PHHx) block were for the first time produced successfully by a recombinant Pseudomonas putida KT2442 with its β-oxidation cycle deleted to its maximum. The chloroform extracted polymers were characterized by nuclear magnetic resonance (NMR), thermo- and mechanical analysis. NMR confirmed the existence of diblock copolymers consisting of 58 mol% PHB as the short chain length block with 42 mol% PHHx as the medium chain length block. The block copolymers had two glass transition temperatures (Tg) at 2.7°C and -16.4°C, one melting temperature (Tm) at 172.1°C and one cool crystallization temperature (Tc) at 69.1°C as revealed by differential scanning calorimetry (DSC), respectively. This is the first microbial short-chain-length (scl) and medium-chain-length (mcl) PHA block copolymer reported. It is possible to produce PHA block copolymers of various kinds using the recombinant Pseudomonas putida KT2442 with its β-oxidation cycle deleted to its maximum. In comparison to a random copolymer poly-3-hydroxybutyrate-co-3-hydroxyhexanoate (P(HB-co-HHx)) and a blend sample of PHB and PHHx, the PHB-b-PHHx showed improved structural related mechanical properties.

Microphase separation of comb copolymers with two different lengths of side chains

NASA Astrophysics Data System (ADS)

Aliev, M. A.; Kuzminyh, N. Yu.

2009-10-01

The phase behavior of the monodisperse AB comb copolymer melt contained the macromolecules of special architecture is discussed. Each macromolecule is assumed to be composed of two comb blocks which differ in numbers of side chains and numbers of monomer units in these chains. It is shown (by analysis of the structure factor of the melt) that microphase separation at two different length scales in the melt is possible. The large and small length scales correspond to separation between comb blocks and separation between monomer units in repeating fragments of blocks, respectively. The classification diagrams indicated which length scale is favored for a given parameters of chemical structure of macromolecules are constructed.

Terahertz spectral change associated with glass transition of poly-ε-caprolactone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Komatsu, Marina, E-mail: mkomatsu@toki.waseda.jp; Mizuno, Maya; Fukunaga, Kaori

2015-04-07

We measured absorption spectra of unidirectionally stretched poly-ε-caprolactone (PCL) film in a range from 0.3 to 3.6 THz at temperatures from 10 to 300 K. Several absorption peaks were observed, when the electric field of THz waves was set in directions parallel and perpendicular to the stretching direction. The absorption bandwidths became significantly broad at around 200 K and above at least in two specific peaks. This temperature is close to the glass transition temperature of PCL. Further, it is shown by quantum chemical calculations that all the peaks obtained experimentally originate in skeletal vibrations of PCL. Therefore, it has become clear thatmore » a specific feature appears in the THz absorption spectrum of PCL associated with its glass transition.« less

Microencapsulation of superoxide dismutase into poly(epsilon-caprolactone) microparticles by reverse micelle solvent evaporation.

PubMed

Youan, Bi-Botti Célestin

2003-01-01

The aim of this work was to encapsulate superoxide dismutase (SOD) in poly(epsilon-caprolactone) (PCL) microparticles by reverse micelle solvent evaporation. The concentration of PCL, the hydrophile-lipophile balance (HLB), and concentration of the sucrose ester used as surfactant in the organic phase were investigated as formulation variables. Relatively higher encapsulation efficiency (approximately 48%) and retained enzymatic activity (>90%) were obtained with microparticle formulation made from the 20% (w/v) PCL and 0.05% (w/v) sucrose ester of HLB = 6. This formulation allowed the in vitro release of SOD for at least 72 hr. These results showed that reverse micelle solvent evaporation can be used to efficiently encapsulate SOD in PCL microparticles. Such formulations may improve the bioavailability of SOD.

Asymmetrical flow field-flow fractionation with multi-angle light scattering and quasi-elastic light scattering for characterization of polymersomes: comparison with classical techniques.

PubMed

Till, Ugo; Gaucher-Delmas, Mireille; Saint-Aguet, Pascale; Hamon, Glenn; Marty, Jean-Daniel; Chassenieux, Christophe; Payré, Bruno; Goudounèche, Dominique; Mingotaud, Anne-Françoise; Violleau, Frédéric

2014-12-01

Polymersomes formed from amphiphilic block copolymers, such as poly(ethyleneoxide-b-ε-caprolactone) (PEO-b-PCL) or poly(ethyleneoxide-b-methylmethacrylate), were characterized by asymmetrical flow field-flow fractionation coupled with quasi-elastic light scattering (QELS), multi-angle light scattering (MALS), and refractive index detection, leading to the determination of their size, shape, and molecular weight. The method was cross-examined with more classical ones, like batch dynamic and static light scattering, electron microscopy, and atomic force microscopy. The results show good complementarities between all the techniques; asymmetrical flow field-flow fractionation being the most pertinent one when the sample exhibits several different types of population.

Introgression of a Block of Genome Under Infinitesimal Selection.

PubMed

Sachdeva, Himani; Barton, Nicholas H

2018-06-12

Adaptive introgression is common in nature and can be driven by selection acting on multiple, linked genes. We explore the effects of polygenic selection on introgression under the infinitesimal model with linkage. This model assumes that the introgressing block has an effectively infinite number of loci, each with an infinitesimal effect on the trait under selection. The block is assumed to introgress under directional selection within a native population that is genetically homogeneous. We use individual-based simulations and a branching process approximation to compute various statistics of the introgressing block, and explore how these depend on parameters such as the map length and initial trait value associated with the introgressing block, the genetic variability along the block, and the strength of selection. Our results show that the introgression dynamics of a block under infinitesimal selection are qualitatively different from the dynamics of neutral introgression. We also find that in the long run, surviving descendant blocks are likely to have intermediate lengths, and clarify how their length is shaped by the interplay between linkage and infinitesimal selection. Our results suggest that it may be difficult to distinguish the long-term introgression of a block of genome with a single strongly selected locus from the introgression of a block with multiple, tightly linked and weakly selected loci. Copyright © 2018, Genetics.

Morphology, drug release, antibacterial, cell proliferation, and histology studies of chamomile-loaded wound dressing mats based on electrospun nanofibrous poly(ɛ-caprolactone)/polystyrene blends.

PubMed

Motealleh, Behrooz; Zahedi, Payam; Rezaeian, Iraj; Moghimi, Morvarid; Abdolghaffari, Amir Hossein; Zarandi, Mohammad Amin

2014-07-01

For the first time, it has been tried to achieve optimum conditions for electrospun poly(ε-caprolactone)/polystyrene (PCL/PS) nanofibrous samples as active wound dressings containing chamomile via D-optimal design approach. In this work, systematic in vitro and in vivo studies were carried out by drug release rate, antibacterial and antifungal evaluations, cell culture, and rat wound model along with histology observation. The optimized samples were prepared under the following electrospinning conditions: PCL/PS ratio (65/35), PCL concentration 9%(w/v), PS concentration 14%(w/v), distance between the syringe needle tip and the collector 15.5 cm, applied voltage 18 kV, and solution flow rate 0.46 mL h(-1) . The FE-SEM micrographs showed electrospun PCL/PS (65/35) nanofibrous sample containing 15% chamomile had a minimum average diameter (∼175 nm) compared to the neat samples (∼268 nm). The drug released resulted in a gradual and high amount of chamomile from the optimized PCL/PS nanofibrous sample (∼70%) in respect to PCL and PS nanofibers after 48 h. This claim was also confirmed by antibacterial and antifungal evaluations in which an inhibitory zone with a diameter of about 7.6 mm was formed. The rat wound model results also indicated that the samples loaded with 15% chamomile extract were remarkably capable to heal the wounds up to 99 ± 0.5% after 14 days post-treatment periods. The adhesion of mesenchymal stem cells and their viability on the optimized samples were confirmed by MTT analysis. Also, the electrospun nanofibrous mats based on PCL/PS (65/35) showed a high efficiency in the wound closure and healing process compared to the reference sample, PCL/PS nanofibers without chamomile. Finally, the histology analysis revealed that the formation of epithelial tissues, the lack of necrosis and collagen fibers accumulation in the dermis tissues for the above optimized samples. © 2013 Wiley Periodicals, Inc.

Tibial Slope Strongly Influences Knee Stability After Posterior Cruciate Ligament Reconstruction: A Prospective 5- to 15-Year Follow-up.

PubMed

Gwinner, Clemens; Weiler, Andreas; Roider, Manoussos; Schaefer, Frederik M; Jung, Tobias M

2017-02-01

The reported failure rate after posterior cruciate ligament (PCL) reconstruction remains high. Previous studies have shown that the tibial slope (TS) influences sagittal plane laxity. Consequently, alterations of TS might have an effect on postoperative knee stability after PCL reconstruction. We hypothesized that flattening of TS is associated with increased posterior laxity after PCL reconstruction. Cohort study; Level of evidence 3. This study consisted of 48 patients who underwent PCL reconstruction in a single-surgeon series. Eight patients underwent an isolated PCL reconstruction, 27 patients underwent an additional posterolateral corner reconstruction, and 13 patients underwent a combined reconstruction of the PCL, anterior cruciate ligament, and posterolateral corner. Three blinded observers measured TS and the side-to-side difference (SSD) of posterior tibial translation (PTT) before and after PCL reconstruction using standardized stress radiographs. The minimum follow-up was 5 years. At a mean follow-up of 103 months (range, 65-187), the mean SSD of PTT was significantly reduced (10.9 ± 2.9 vs 4.9 ± 4.3 mm; P < .0001). The mean TS was 8.0° ± 3.7° (range, 1°-14.3°) for the operated knee and 7.9° ± 3.2° (range, 2°-15.3°) for the contralateral knee. There was a statistically significant correlation between TS and PTT ( r = -0.77 and R 2 = 0.59; P < .0001). In addition, there was a significant correlation between TS and the postoperative reduction of PTT ( r = 0.74 and R 2 = 0.55; P < .0001). Subgrouping according to the number of operated ligaments showed no significant differences regarding TS or the mean reduction of PTT. Flattening of TS is associated with a significantly higher remaining PTT as well as a lower reduction of PTT. Notably, these results are irrespective of sex and number of ligaments addressed. Thus, isolated soft tissue procedures in PCL deficiency may only incompletely address posterior knee instability in patients with flattening of the posterior slope.

Comparative study of design and PCL-substituting systems of total knee prosthesis.

PubMed

Adam, R; Orban, C; Orban, H

2014-01-01

The aim of this study is to assess postoperative results obtained by different knee implants. The main implant types differences are given by generally implant design and by PCL substituting systems that are used. Between 04.2004 - 02.2012 we have performed 506 total knee arthroplasties (TKA), on a group of 460 patients. Our choice, was for cemented total knee prostheses, using PCL-substituting systems. Regarding general design and PCL-substituting systems of the implant we had divided the main group in three lots. In order to assess post operative result we had used the American Knee Society Score(AKSS). All prostheses types that we had implanted, had registered satisfactory values of AKSS. Our study showed that one group scored higher values of AKSS, compared the other two, but there are not statistical semnificative differences (p=0,09). Celsius.

Bactericidal Dendritic Polycation Cloaked with Stealth Material via Lipase-Sensitive Intersegment Acquires Neutral Surface Charge without Losing Membrane-Disruptive Activity.

PubMed

Xu, Lulu; He, Chen; Hui, Liwei; Xie, Yuntao; Li, Jia-Min; He, Wei-Dong; Yang, Lihua

2015-12-23

Net cationicity of membrane-disruptive antimicrobials is necessary for their activity but may elicit immune attack when administered intravenously. By cloaking a dendritic polycation (G2) with poly(caprolactone-b-ethylene glycol) (PCL-b-PEG), we obtain a nanoparticle antimicrobial, G2-g-(PCL-b-PEG), which exhibits neutral surface charge but kills >99.9% of inoculated bacterial cells at ≤8 μg/mL. The observed activity may be attributed PCL's responsive degradation by bacterial lipase and the consequent exposure of the membrane-disruptive, bactericidal G2 core. Moreover, G2-g-(PCL-b-PEG) exhibits good colloidal stability in the presence of serum and insignificant hemolytic toxicity even at ≥2048 μg/mL. suggesting good blood compatibility required for intravenous administration.

Investigation of nanoyarn preparation by modified electrospinning setup.

PubMed

Levitt, Ariana S; Knittel, Chelsea E; Vallett, Richard; Koerner, Michael; Dion, Genevieve; Schauer, Caroline L

2017-05-15

Higher ordered structures of nanofibers, including nanofiber-based yarns and cables, have a variety of potential applications, including wearable health monitoring systems, artificial tendons, and medical sutures. In this study, twisted assemblies of polyacrylonitrile (PAN), polyvinylidene fluoride trifluoroethylene (PVDF-TrFE), and polycaprolactone (PCL) nanofibers were fabricated via a modified electrospinning setup, consisting of a rotating cone-shaped copper collector, two syringe pumps, and two high voltage power supplies. The fiber diameters and twist angles varied as a function of the rotary speed of the collector. Mechanical testing of the yarns revealed that PVDF-TrFe and PCL yarns have a higher strain-to-failure than PAN yarns, reaching 307% for PCL nanoyarns. For the first time, the porosity of nanofiber yarns was studied as a function of twist angle, showing that PAN nanoyarns are more porous than PCL yarns.

The Psychological Inventory of Criminal Thinking Styles and Psychopathy Checklist: screening version as incrementally valid predictors of recidivism.

PubMed

Walters, Glenn D

2009-12-01

A follow-up of 107 male federal prison inmates previously tested with the Psychological Inventory of Criminal Thinking Styles (PICTS) and Psychopathy Checklist: Screening Version (PCL:SV) was conducted to test the incremental validity of both measures. The PICTS General Criminal Thinking (GCT) score was found to predict general recidivism and serious recidivism when age, prior charges, and the PCL:SV were controlled. The PCL:SV, on the other hand, failed to predict general and serious recidivism when age, prior charges, and the PICTS were controlled. These findings support the hypothesis that content-relevant self-report measures like the PICTS are capable of predicting crime-relevant outcomes above and beyond the contributions of basic demographic variables like age, criminal history, and such popular non-self-report rating procedures as the PCL:SV.

A Nanostructured Degradable Ureteral Stent Fabricated by Electrospinning for Upper Urinary Tract Reconstruction.

PubMed

Wang, Xiaoqing; Zhang, Long; Chen, Qihui; Hou, Yuchuan; Hao, Yuanyuan; Wang, Chunxi; Shan, Hongli

2015-12-01

A degradable polycaprolactone(PCL)/poly(lactic-co-glycolic acid, LA:GA = 80:20) (PLGA) ureter tubular stent was fabricated by electrospinning. The structure and properties of the stents were investigated by the mechanical property testing, scanning electron microscopy (SEM), degradability test in vitro and MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay. The stent was transplanted to the dorsal muscle of rabbit to evaluate its tissue compatibility. It was shown that the stent has the nano-structure. The mechanical test showed that with the increase in PCL concentration, the mechanical properties of the stent gradually increased, and it could meet the demands of a urethral stent. The collapse time of different concentration of PCL/PLGA (5%, 15%, and 25%) was 28, 42, and 56 days, respectively. These results provide strong evidence that the degradation time can be increased with the increase in PCL concentration. The results of the MTT assay show that the PCL/PLGA stent had no cytotoxicity. In muscle implantation tests, acute tissue reactions due to operation trauma were seen in all specimens at 1 week. After four weeks, the number of inflammatory cells had decreased significantly. Only a few inflammatory cells were seen in the PCL/PLGA stent group after 12 weeks, and the foreign body reaction was more severe in the control group. Animal orthotopic transplantation experiments of these ureteral stents will be done to evaluate its degradable model and tissue compatibility.

Dermal-epidermal membrane systems by using human keratinocytes and mesenchymal stem cells isolated from dermis.

PubMed

Salerno, Simona; Messina, Antonietta; Giordano, Francesca; Bader, Augustinus; Drioli, Enrico; De Bartolo, Loredana

2017-02-01

Dermal-epidermal membrane systems were developed by co-culturing human keratinocytes with Skin derived Stem Cells (SSCs), which are Mesenchymal Stem Cells (MSCs) isolated from dermis, on biodegradable membranes of chitosan (CHT), polycaprolactone (PCL) and a polymeric blend of CHT and PCL. The membranes display physico-chemical, morphological, mechanical and biodegradation properties that could satisfy and fulfil specific requirements in skin tissue engineering. CHT membrane exhibits an optimal biodegradation rate for acute wounds; CHT-PCL for the chronic ones. On the other hand, PCL membrane in spite of its very slow biodegradation rate exhibits mechanical properties similar to in vivo dermis, a lower hydrophilic character, and a surface roughness, all properties that make it able to sustain cell adhesion and proliferation for in vitro skin models. Both CHT-PCL and PCL membranes guided epidermal and dermal differentiation of SSCs as pointed out by the expression of cytokeratins and the deposition of the ECM protein fibronectin, respectively. In the dermal-epidermal membrane systems, a more suitable microenvironment for the SSCs differentiation was promoted by the interactions and the mutual interplay with keratinocytes. Being skin tissue-biased stem cells committed to their specific final dermal and/or epidermal cell differentiation, SSCs are more suitable for skin tissue engineering than other adult MSCs with different origin. For this reason, they represent a useful autologous cell source for engineering skin substitutes for both in vivo and in vitro applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Enhanced biocompatibility and osteogenic potential of mesoporous magnesium silicate/polycaprolactone/wheat protein composite scaffolds.

PubMed

Kang, Yun Gyeong; Wei, Jie; Shin, Ji Won; Wu, Yan Ru; Su, Jiacan; Park, Young Shik; Shin, Jung-Woog

2018-01-01

Successful bone tissue engineering using scaffolds is primarily dependent on the properties of the scaffold, including biocompatibility, highly interconnected porosity, and mechanical integrity. In this study, we propose new composite scaffolds consisting of mesoporous magnesium silicate (m_MS), polycaprolactone (PCL), and wheat protein (WP) manufactured by a rapid prototyping technique to provide a micro/macro porous structure. Experimental groups were set based on the component ratio: (1) WP0% (m_MS:PCL:WP =30:70:0 weight per weight; w/w); (2) WP15% (m_MS:PCL:WP =30:55:15 w/w); (3) WP30% (m_MS:PCL:WP =30:40:30 w/w). Evaluation of the properties of fabricated scaffolds indicated that increasing the amount of WP improved the surface hydrophilicity and biodegradability of m_MS/PCL/WP composites, while reducing the mechanical strength. Moreover, experiments were performed to confirm the biocompatibility and osteogenic differentiation of human mesenchymal stem cells (MSCs) according to the component ratio of the scaffold. The results confirmed that the content of WP affects proliferation and osteogenic differentiation of MSCs. Based on the last day of the experiment, ie, the 14th day, the proliferation based on the amount of DNA was the best in the WP30% group, but all of the markers measured by PCR were the most expressed in the WP15% group. These results suggest that the m_MS/PCL/WP composite is a promising candidate for use as a scaffold in cell-based bone regeneration.

[Effect of posterior cruciate ligament retaining or not on knee-joint proprioception].

PubMed

Wu, Yansheng; Li, Yongsheng; Chen, Baicheng

2013-07-01

To analyze the effect of the posterior cruciate ligament (PCL) retaining or not on knee-joint proprioception by comparing the proprioceptive difference between PCL retaining and no PCL retaining in total knee arthroplasty (TKA). Between June 2009 and June 2010, 38 osteoarthritis patients meeting the inclusion criteria were divided into PCL retaining group (group A, n=19) and PCL-substituting group (group B, n=19) according to the random number table. There was no significant difference in gender, age, disease duration, the range of motion of the knee between 2 groups (P > 0.05). The effectiveness and the knee-joint proprioception were separately assessed by the Western Ontario and McMaster University Osteoarthritis Index (WOMAC) score and the passive angle reproduction test (30, 60, and 90 degrees of knee flexion) preoperatively and 12 months postoperatively. All incisons healed by first intention, without complications of infection, fracture, and deep vein thrombosis of lower limb. The patients were followed up 12-17 months (mean, 14.1 months). The knee function after operation was obviously improved when compared with preoperative one; significant differences were observed in the WOMAC scores and the results of passive angle reproduction test between at preoperation and at 12 months after operation (P < 0.05), but no significant difference was found between group A and group B (P > 0.05). Whether PCL retaining or not in TKA both can improve knee-joint proprioception, and no obvious difference between them.

Evaluation of multi-scale mineralized collagen-polycaprolactone composites for bone tissue engineering.

PubMed

Weisgerber, D W; Erning, K; Flanagan, C L; Hollister, S J; Harley, B A C

2016-08-01

A particular challenge in biomaterial development for treating orthopedic injuries stems from the need to balance bioactive design criteria with the mechanical and geometric constraints governed by the physiological wound environment. Such trade-offs are of particular importance in large craniofacial bone defects which arise from both acute trauma and chronic conditions. Ongoing efforts in our laboratory have demonstrated a mineralized collagen biomaterial that can promote human mesenchymal stem cell osteogenesis in the absence of osteogenic media but that possesses suboptimal mechanical properties in regards to use in loaded wound sites. Here we demonstrate a multi-scale composite consisting of a highly bioactive mineralized collagen-glycosaminoglycan scaffold with micron-scale porosity and a polycaprolactone support frame (PCL) with millimeter-scale porosity. Fabrication of the composite was performed by impregnating the PCL support frame with the mineral scaffold precursor suspension prior to lyophilization. Here we evaluate the mechanical properties, permeability, and bioactivity of the resulting composite. Results indicated that the PCL support frame dominates the bulk mechanical response of the composite resulting in a 6000-fold increase in modulus compared to the mineral scaffold alone. Similarly, the incorporation of the mineral scaffold matrix into the composite resulted in a higher specific surface area compared to the PCL frame alone. The increased specific surface area in the collagen-PCL composite promoted increased initial attachment of porcine adipose derived stem cells versus the PCL construct. Copyright © 2016 Elsevier Ltd. All rights reserved.

Eco-friendly films prepared from plantain flour/PCL blends under reactive extrusion conditions using zirconium octanoate as a catalyst.

PubMed

Gutiérrez, Tomy J; Alvarez, Vera A

2017-12-15

Plantain flour (Musa ssp., group AAB, sub-group clone Harton)/poly(ε-caprolactone) (PCL) blends, containing glycerol as a plasticizer, were prepared by reactive extrusion (REx) in a twin-screw extruder using zirconium octanoate (Zr(Oct) 4 ) as a catalyst, followed by thermo-compression molding for film development. The films were then characterized in terms of their: infrared (FTIR) spectra, water solubility, thermogravimetric (TGA) curves, differential scanning calorimetry (DSC) thermograms, and X-ray diffraction (XDR) diffractograms, as well as their microstructural, mechanical and antimicrobial properties in order to (1) compare the effects of PCLs with two different molecular weights (M w ) on the characteristics of the plantain flour/PCL blends, and (2) determine whether using Zr(Oct) 4 in the production of active composite polymer materials improves their properties. The plantain flour/PCL blends were all developed successfully. The higher M w PCL gave more hydrophobic and thermally stable films with improved mechanical properties. The addition of the Zr(Oct) 4 catalyst to the plantain flour/PCL blends also resulted in films with similar characteristics to those described above, due to the cross-linking of the polymers. In addition, the films containing the catalyst showed antimicrobial activity against Escherichia coli O157:H7 and Staphylococcus aureus indicating a dual effect of Zr(Oct) 4 , and making it an attractive alternative for the development of active films. Copyright © 2017 Elsevier Ltd. All rights reserved.

Synergistic activity of tenofovir and nevirapine combinations released from polycaprolactone matrices for potential enhanced prevention of HIV infection through the vaginal route.

PubMed

Dang, Nhung T T; Sivakumaran, Haran; Harrich, David; Shaw, Paul N; Davis-Poynter, Nicholas; Coombes, Allan G A

2014-10-01

Polycaprolactone (PCL) matrices were simultaneously loaded with the antiviral agents, tenofovir (TFV) and nevirapine (NVP), in combination to provide synergistic activity in the prevention of HIV transmission through the vaginal route. TFV and NVP were incorporated in PCL matrices at theoretical loadings of 10%TFV-10% NVP, 5%TFV-5%NVP and 5%TFV-10%NVP, measured with respect to the PCL content of the matrices. Actual TFV loadings ranged from 2.1% to 4.2% equating to loading efficiencies of about 41-42%. The actual loadings of NVP were around half those of TFV (1.2-1.9%), resulting in loading efficiencies ranging from 17.2% to 23.5%. Approximately 80% of the initial content of TFV was released from the PCL matrices into simulated vaginal fluid (SVF) over a period of 30 days, which was almost double the cumulative release of NVP (40-45%). The release kinetics of both antivirals over 30 days were found to be described most satisfactorily by the Higuchi model. In vitro assay of release media containing combinations of TFV and NVP released from PCL matrices confirmed a potential synergistic/additive effect of the released antivirals on HIV-1 infection of HeLa cells. These findings indicate that PCL matrices loaded with combinations of TFV and NVP provide an effective strategy for the sustained vaginal delivery of antivirals with synergistic/additive activity. Copyright © 2014 Elsevier B.V. All rights reserved.

Psychometric properties of the PTSD Checklist for Diagnostic and Statistical Manual of Mental Disorders-Fifth Edition (PCL-5) in veterans.

PubMed

Bovin, Michelle J; Marx, Brian P; Weathers, Frank W; Gallagher, Matthew W; Rodriguez, Paola; Schnurr, Paula P; Keane, Terence M

2016-11-01

This study examined the psychometric properties of the posttraumatic stress disorder (PTSD) Checklist for Diagnostic and Statistical Manual of Mental Disorders-Fifth Edition (PCL-5; Weathers, Litz, et al., 2013b) in 2 independent samples of veterans receiving care at a Veterans Affairs Medical Center (N = 468). A subsample of these participants (n = 140) was used to define a valid diagnostic cutoff score for the instrument using the Clinician-Administered PTSD Scale for DSM-5 (CAPS-5; Weathers, Blake, et al., 2013) as the reference standard. The PCL-5 test scores demonstrated good internal consistency (α = .96), test-retest reliability (r = .84), and convergent and discriminant validity. Consistent with previous studies (Armour et al., 2015; Liu et al., 2014), confirmatory factor analysis revealed that the data were best explained by a 6-factor anhedonia model and a 7-factor hybrid model. Signal detection analyses using the CAPS-5 revealed that PCL-5 scores of 31 to 33 were optimally efficient for diagnosing PTSD (κ(.5) = .58). Overall, the findings suggest that the PCL-5 is a psychometrically sound instrument that can be used effectively with veterans. Further, by determining a valid cutoff score using the CAPS-5, the PCL-5 can now be used to identify veterans with probable PTSD. However, findings also suggest the need for research to evaluate cluster structure of DSM-5. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Bioactive nano-fibrous scaffold for vascularized craniofacial bone regeneration.

PubMed

Prabha, Rahul Damodaran; Kraft, David Christian Evar; Harkness, Linda; Melsen, Birte; Varma, Harikrishna; Nair, Prabha D; Kjems, Jorgen; Kassem, Moustapha

2018-03-01

There has been a growing demand for bone grafts for correction of bone defects in complicated fractures or tumours in the craniofacial region. Soft flexible membrane like material that could be inserted into defect by less invasive approaches; promote osteoconductivity and act as a barrier to soft tissue in growth while promoting bone formation is an attractive option for this region. Electrospinning has recently emerged as one of the most promising techniques for fabrication of extracellular matrix such as nano-fibrous scaffolds that can serve as a template for bone formation. To overcome the limitation of cell penetration of electrospun scaffolds and improve on its osteoconductive nature, in this study, we fabricated a novel electrospun composite scaffold of polyvinyl alcohol (PVA)-poly (ε) caprolactone (PCL)-Hydroxyapatite based bioceramic (HAB), namely, PVA-PCL-HAB. The scaffold prepared by dual electrospinning of PVA and PCL with HAB overcomes reduced cell attachment associated with hydrophobic PCL by combination with a hydrophilic PVA and the HAB can contribute to enhance osteoconductivity. We characterized the physicochemical and biocompatibility properties of the new scaffold material. Our results indicate PVA-PCL-HAB scaffolds support attachment and growth of stromal stem cells; [human bone marrow skeletal (mesenchymal) stem cells and dental pulp stem cells]. In addition, the scaffold supported in vitro osteogenic differentiation and in vivo vascularized bone formation. Thus, PVA-PCL-HAB scaffold is a suitable potential material for therapeutic bone regeneration in dentistry and orthopaedics. Copyright © 2017 John Wiley & Sons, Ltd.

Combined electrohydraulic and holmium: YAG laser ureteroscopic nephrolithotripsy of large (>2 cm) renal calculi

PubMed Central

Mariani, Albert J.

2008-01-01

Percutaneous nephrolithotripsy (PCL) is a standard treatment for renal calculi >2 cm. Modern flexible ureteroscopes and accessories employing the complementary effects of electrohydraulic lithotripsy (EHL) and Ho:YAG laser lithotrites can treat these renal calculi in a minimally invasive fashion with similar or superior results. Objective: To assess the safety and efficacy of ureteroscopic nephrolithotripsy monotherapy for the management of >2 cm renal calculi in the community setting. Materials and Methods: Fifty nine patients with 63 renal calculi ranging from 20 to 97 mm (mean 44 mm) in length and 175 to 3300 mm2 (mean 728 mm2) area underwent staged ureteroscopic nephrolithotripsy monotherapy. Obesity (BMI > 30) was present in 54% and 19% were morbidly obese (BMI > 40). An infectious etiology was present in 49% and hard stone components in 89%. All patients presented with hematuria, pain, and/or recurrent urinary tract infection (UTI). Lithotripsy was performed with a single deflection flexible ureteroscope and predominantly EHL. Laser drilling was employed (n = 6) to weaken very hard stones prior to EHL. Low intrarenal pressure was maintained by continuous bladder drainage and placement of a stiff safety wire. Visibility was maintained using manual pulsatile irrigation. Results: All patients were rendered pain and infection-free. No patient required a blood transfusion and there was no change in serum creatinine. Mobile stone-free status was achieved in 60/63 (95%) with a mean of 1.7 nephrolithotripsy stages and 0.38 secondary or ancillary procedures. Outpatient management was sufficient for 121/131 (92%) of the procedures. Operative time averaged 46 min/stage and 79 min/calculus. Complications included endotoxic shock (3), fever (5), ureteral fragments requiring treatment (11), delayed extubation (2), delayed pneumonia (1), and urinary retention (1). Conclusion: Staged ureteroscopic nephrolithotripsy of large renal calculi is feasible with low morbidity and stone clearance rates that compare favorably with PCL. It has largely replaced PCL at this institution. PMID:19468511

Time-course of PTSD symptoms in the Australian Defence Force: a retrospective cohort study.

PubMed

Waller, M; Charlson, F J; Ireland, R E E; Whiteford, H A; Dobson, A J

2016-08-01

Understanding the time-course of post-traumatic stress disorder (PTSD), and the underlying events, may help to identify those most at risk, and anticipate the number of individuals likely to be diagnosed after exposure to traumatic events. Data from two health surveys were combined to create a cohort of 1119 Australian military personnel who deployed to the Middle East between 2000 and 2009. Changes in PTSD Checklist Civilian Version (PCL-C) scores and the reporting of stressful events between the two self-reported surveys were assessed. Logistic regression was used to examine the association between the number of stressful events reported and PTSD symptoms, and assess whether those who reported new stressful events between the two surveys, were also more likely to report older events. We also assessed, using linear regression, whether higher scores on the Kessler Psychological Distress Scale or the Alcohol Use Disorder Identification Test were associated with subsequent increases in the PCL-C in those who had experienced a stressful event, but who initially had few PTSD symptoms. Overall, the mean PCL-C scores in the two surveys were similar, and 78% of responders stayed in the same PCL-C category. Only a small percentage moved from having few symptoms of PTSD (PCL-C < 30) in Survey 1 to meeting the criteria for PTSD (PCL-C ≥ 50) at Survey 2 (1% of all responders, 16% of those with PCL-C ≥ 50 at Survey 2). Personnel who reported more stressful lifetime events were more likely to score higher on the PCL-C. Only 51% reported the same stressful event on both surveys. People who reported events occurring between the two surveys were more likely to record events from before the first survey which they had not previously mentioned (OR 1.48, 95% CI (1.17, 1.88), p < 0.001), than those who did not. In people who initially had few PTSD symptoms, a higher level of psychological distress, was significantly associated with higher PCL-C scores a few years later. The reporting of stressful events varied over time indicating that while the impact of some stressors endure, others may increase or decline in importance. When screening for PTSD, it is important to consider both traumatic experiences on deployment and other stressful life events, as well as other mental health problems among military personnel, even if individuals do not exhibit symptoms of PTSD on an initial assessment.

Effect of hydroxyapatite nano-particles on morphology, rheology and thermal behavior of poly(caprolactone)/chitosan blends.

PubMed

Ghorbani, Fereshte Mohammad; Kaffashi, Babak; Shokrollahi, Parvin; Akhlaghi, Shahin; Hedenqvist, Mikael S

2016-02-01

The effect of hydroxyapatite nano-particles (nHA) on morphology, and rheological and thermal properties of PCL/chitosan blends was investigated. The tendency of nHA to reside in the submicron-dispersed chitosan phase is determined using SEM and AFM images. The presence of electrostatic interaction between amide sites of chitosan and ionic groups on the nHA surface was proved by FTIR. It is shown that the chitosan phase is thermodynamically more favorable for the nano-particles to reside than the PCL phase. Lack of implementation of Cox-Merz theory for this system shows that the polymer-nano-particle network is destructed by the flow. Results from dynamic rheological measurements and Zener fractional model show that the presence of nHA increases the shear moduli and relaxation time of the PCL/chitosan blends. DSC measurements showed that nHA nano-particles are responsible for the increase in melting and crystallization characteristics of the PCL/chitosan blends. Based on thermogravimetric analysis, the PCL/chitosan/nHA nano-composites exhibited a greater thermal stability compared to the nHA-free blends. Copyright © 2015 Elsevier B.V. All rights reserved.

Polydopamine-Functionalized CA-(PCL-ran-PLA) Nanoparticles for Target Delivery of Docetaxel and Chemo-photothermal Therapy of Breast Cancer

PubMed Central

Kong, Na; Deng, Mei; Sun, Xiu-Na; Chen, Yi-Ding; Sui, Xin-Bing

2018-01-01

Current limitations of cancer therapy include the lack of effective strategy for target delivery of chemotherapeutic drugs, and the difficulty of achieving significant efficacy by single treatment. Herein, we reported a synergistic chemo-photothermal strategy based on aptamer (Apt)-polydopamine (pD) functionalized CA-(PCL-ran-PLA) nanoparticles (NPs) for effective delivery of docetaxel (DTX) and enhanced therapeutic effect. The developed DTX-loaded Apt-pD-CA-(PCL-ran-PLA) NPs achieved promising advantages, such as (i) improved drug loading content (LC) and encapsulation efficiency (EE) initiated by star-shaped copolymer CA-(PCL-ran-PLA); (ii) effective target delivery of drugs to tumor sites by incorporating AS1411 aptamers; (iii) significant therapeutic efficacy caused by synergistic chemo-photothermal treatment. In addition, the pD coating strategy with simple procedures could address the contradiction between targeting modification and maintaining formerly excellent bio-properties. Therefore, with excellent bio-properties and simple preparation procedures, the DTX-loaded Apt-pD-CA-(PCL-ran-PLA) NPs effectively increased the local drug concentration in tumor sites, minimized side effects, and significantly eliminated tumors, indicating the promising application of these NPs for cancer therapy. PMID:29527167

Hybrid PCL/CaCO3 scaffolds with capabilities of carrying biologically active molecules: Synthesis, loading and in vivo applications.

PubMed

Saveleva, M S; Ivanov, A N; Kurtukova, M O; Atkin, V S; Ivanova, A G; Lyubun, G P; Martyukova, A V; Cherevko, E I; Sargsyan, A K; Fedonnikov, A S; Norkin, I A; Skirtach, A G; Gorin, D A; Parakhonskiy, B V

2018-04-01

Designing advanced biomaterials for tissue regeneration with drug delivery and release functionalities remains a challenge in regenerative medicine. In this research, we have developed novel composite scaffolds based on polymeric polycaprolactone fibers coated with porous calcium carbonate structures (PCL/CaCO 3 ) for tissue engineering and have shown their drug delivery and release in rats. In vivo biocompatibility tests of PCL/CaCO 3 scaffolds were complemented with in vivo drug release study, where tannic acid (TA) was used as a model drug. Release of TA from the scaffolds was realized by recrystallization of the porous vaterite phase of calcium carbonate into the crystalline calcite. Cell colonization and tissue vascularization as well as transplantability of developed PCL/CaCO 3 +TA scaffolds were observed. Detailed study of scaffold transformations during 21-day implantation period was followed by scanning electron microscopy and X-ray diffraction studies before and after in vivo implantation. The presented results demonstrate that PCL/CaCO 3 scaffolds are attractive candidates for implants in bone regeneration and tissue engineering with a possibility of loading biologically active molecules and controlled release. Copyright © 2017 Elsevier B.V. All rights reserved.

Controlled release of an antibiotic, gentamicin sulphate, from gravity spun polycaprolactone fibers.

PubMed

Chang, H-I; Lau, Y-C; Yan, C; Coombes, A G A

2008-01-01

The antibiotic, gentamicin sulphate (GS), was incorporated in gravity-spun polycaprolactone (PCL) fibers by spinning from particulate suspensions of the drug in PCL solution to produce a controlled delivery system. The production rate of GS-loaded PCL fibers was confined to the range 1-1.5 m/min and the fiber diameter to 170-220 microm. The kinetics of drug release could be adjusted by varying the GS loading of the fibers and the suspension preparation conditions. Gradual release of approximately 80% of the initial GS content was measured in phosphate buffered saline at 37 degrees C over 50 days from fibers spun from nonhomogenized suspensions, whereas loss of this amount of antibiotic occurred in less than 10 days from fibers spun from homogenized suspensions. Studies of growth inhibition of Stapyhlococcus epidermidis in culture indicated that GS released after 2 weeks from PCL fibers retained antibacterial activity. This behavior recommends further investigation of PCL fibers for local delivery of antibiotics to combat infection associated with periodontal disease, musculoskeletal injuries, and implantation of fiber-based tissue substitutes such as vascular prostheses. (c) 2007 Wiley Periodicals, Inc. J Biomed Mater Res, 2008.

The efficacy of polycaprolactone/hydroxyapatite scaffold in combination with mesenchymal stem cells for bone tissue engineering.

PubMed

Chuenjitkuntaworn, Boontharika; Osathanon, Thanaphum; Nowwarote, Nunthawan; Supaphol, Pitt; Pavasant, Prasit

2016-01-01

Major drawbacks of using an autograft are the possibilities of insufficient bony source and patient's morbidity after operation. Bone tissue engineering technology, therefore, has been applied for repairing bony defects. Previous study showed that a novel fabricated 3D-Polycaprolactone/Hydroxyapatite (PCL/HAp) scaffold possessed a good biocompatibility for bone cells. This study aimed to determine the ability of PCL/HAp for supporting cell growth, gene expression, and osteogenic differentiation in three types of mesenchymal stem cells, including bone marrow-derived mesenchymal stem cells (BMSCs), dental pulp stem cells (DPSCs), and adiposed-derived mesenchymal stem cells (ADSCs). These were assessed by cell viability assay (MTT), reverse-transcription polymerase chain reaction (RT-PCR) analysis, alkaline phosphatase activity, and osteogenic differentiation by alizarin red-S staining. The results showed that PCL/HAp scaffold could support growth of all three types of mesenchymal stem cells. In addition, DPSCs with PCL/HAp showed the highest level of calcium deposition compared to other groups. In conclusion, DPSCs exhibited a better compatibility with these scaffolds compared to BMSCs and ADSCs. However, the PCL/HAp could be a good candidate scaffold for all tested mesenchymal stem cells in bone tissue engineering. © 2015 Wiley Periodicals, Inc.

Fabrication and Characterization of Electrospun PCL-MgO-Keratin-Based Composite Nanofibers for Biomedical Applications

PubMed Central

Boakye, Maame A. D.; Rijal, Nava P.; Adhikari, Udhab; Bhattarai, Narayan

2015-01-01

Polymeric nanofibers are of great interest in biomedical applications, such as tissue engineering, drug delivery and wound healing, due to their ability to mimic and restore the function of natural extracellular matrix (ECM) found in tissues. Electrospinning has been heavily used to fabricate nanofibers because of its reliability and effectiveness. In our research, we fabricated poly(ε-caprolactone)-(PCL), magnesium oxide-(MgO) and keratin (K)-based composite nanofibers by electrospinning a blend solution of PCL, MgO and/or K. The electrospun nanofibers were analyzed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), mechanical tensile testing and inductively-coupled plasma optical emission spectroscopy (ICP-OES). Nanofibers with diameters in the range of 0.2–2.2 µm were produced by using different ratios of PCL/MgO and PCL-K/MgO. These fibers showed a uniform morphology with suitable mechanical properties; ultimate tensile strength up to 3 MPa and Young’s modulus 10 MPa. The structural integrity of nanofiber mats was retained in aqueous and phosphate buffer saline (PBS) medium. This study provides a new composite material with structural and material properties suitable for potential application in tissue engineering. PMID:28793426

Tunable engineered skin mechanics via coaxial electrospun fiber core diameter.

PubMed

Blackstone, Britani Nicole; Drexler, Jason William; Powell, Heather Megan

2014-10-01

Autologous engineered skin (ES) offers promise as a treatment for massive full thickness burns. Unfortunately, ES is orders of magnitude weaker than normal human skin causing it to be difficult to apply surgically and subject to damage by mechanical shear in the early phases of engraftment. In addition, no manufacturing strategy has been developed to tune ES biomechanics to approximate the native biomechanics at different anatomic locations. To enhance and tune ES biomechanics, a coaxial (CoA) electrospun scaffold platform was developed from polycaprolactone (PCL, core) and gelatin (shell). The ability of the coaxial fiber core diameter to control both scaffold and tissue mechanics was investigated along with the ability of the gelatin shell to facilitate cell adhesion and skin development compared to pure gelatin, pure PCL, and a gelatin-PCL blended fiber scaffold. CoA ES exhibited increased cellular adhesion and metabolism versus PCL alone or gelatin-PCL blend and promoted the development of well stratified skin with a dense dermal layer and a differentiated epidermal layer. Biomechanics of the scaffold and ES scaled linearly with core diameter suggesting that this scaffold platform could be utilized to tailor ES mechanics for their intended grafting site and reduce graft damage in vitro and in vivo.

Intrapleural cisplatin for management of malignant pleural effusion in a patient with plasma cell leucaemia.

PubMed

Agarwal, Abhishek; Klair, Jagpal; Patolia, Setu; Meena, Nikhil K

2015-06-29

Plasma cell leucaemia (PCL) is a rare aggressive form of multiple myeloma. It occasionally involves the pleura, causing malignant pleural effusion (MPE). MPE presents a management dilemma for physicians, given the different treatment options available with varying efficacy and side effects. We report a case of a 64-year-old man with MPE due to PCL, successfully managed with intrapleural cisplatin and a tunnelled pleural catheter. We believe this to be the first report of management of PCL-associated MPE with intrapleural cisplatin. 2015 BMJ Publishing Group Ltd.

In Vitro Evaluation of PCL and P(3HB) as Coating Materials for Selective Laser Melted Porous Titanium Implants.

PubMed

Grau, Michael; Matena, Julia; Teske, Michael; Petersen, Svea; Aliuos, Pooyan; Roland, Laura; Grabow, Niels; Murua Escobar, Hugo; Gellrich, Nils-Claudius; Haferkamp, Heinz; Nolte, Ingo

2017-11-23

Titanium is widely used as a bone implant material due to its biocompatibility and high resilience. Since its Young's modulus differs from bone tissue, the resulting "stress shielding" could lead to scaffold loosening. However, by using a scaffold-shaped geometry, the Young's modulus can be adjusted. Also, a porous geometry enables vascularisation and bone ingrowth inside the implant itself. Additionally, growth factors can improve these effects. In order to create a deposit and release system for these factors, the titanium scaffolds could be coated with degradable polymers. Therefore, in the present study, synthetic poly-ε-caprolactone (PCL) and the biopolymer poly(3-hydroxybutyrate) (P(3HB)) were tested for coating efficiency, cell adhesion, and biocompatibility to find a suitable coating material. The underlying scaffold was created from titanium by Selective Laser Melting (SLM) and coated with PCL or P(3HB) via dip coating. To test the biocompatibility, Live Cell Imaging (LCI) as well as vitality and proliferation assays were performed. In addition, cell adhesion forces were detected via Single Cell Force Spectroscopy, while the coating efficiency was observed using environmental scanning electron microscopy (ESEM) and energy-dispersive X-ray (EDX) analyses. Regarding the coating efficiency, PCL showed higher values in comparison to P(3HB). Vitality assays revealed decent vitality values for both polymers, while values for PCL were significantly lower than those for blank titanium. No significant differences could be observed between PCL and P(3HB) in proliferation and cell adhesion studies. Although LCI observations revealed decreasing values in cell number and populated area over time on both polymer-coated scaffolds, these outcomes could be explained by the possibility of coating diluent residues accumulating in the culture medium. Overall, both polymers fulfill the requirements regarding biocompatibility. Nonetheless, since only PCL coating ensured the maintenance of the porous implant structure, it is preferable to be used as a coating material for creating a deposit and release system for growth factors.

Validity of the posttraumatic stress disorders (PTSD) checklist in pregnant women.

PubMed

Gelaye, Bizu; Zheng, Yinnan; Medina-Mora, Maria Elena; Rondon, Marta B; Sánchez, Sixto E; Williams, Michelle A

2017-05-12

The PTSD Checklist-civilian (PCL-C) is one of the most commonly used self-report measures of PTSD symptoms, however, little is known about its validity when used in pregnancy. This study aims to evaluate the reliability and validity of the PCL-C as a screen for detecting PTSD symptoms among pregnant women. A total of 3372 pregnant women who attended their first prenatal care visit in Lima, Peru participated in the study. We assessed the reliability of the PCL-C items using Cronbach's alpha. Criterion validity and performance characteristics of PCL-C were assessed against an independent, blinded Clinician-Administered PTSD Scale (CAPS) interview using measures of sensitivity, specificity and receiver operating characteristics (ROC) curves. We tested construct validity using exploratory and confirmatory factor analytic approaches. The reliability of the PCL-C was excellent (Cronbach's alpha =0.90). ROC analysis showed that a cut-off score of 26 offered optimal discriminatory power, with a sensitivity of 0.86 (95% CI: 0.78-0.92) and a specificity of 0.63 (95% CI: 0.62-0.65). The area under the ROC curve was 0.75 (95% CI: 0.71-0.78). A three-factor solution was extracted using exploratory factor analysis and was further complemented with three other models using confirmatory factor analysis (CFA). In a CFA, a three-factor model based on DSM-IV symptom structure had reasonable fit statistics with comparative fit index of 0.86 and root mean square error of approximation of 0.09. The Spanish-language version of the PCL-C may be used as a screening tool for pregnant women. The PCL-C has good reliability, criterion validity and factorial validity. The optimal cut-off score obtained by maximizing the sensitivity and specificity should be considered cautiously; women who screened positive may require further investigation to confirm PTSD diagnosis.

Electrospun polycaprolactone/gelatin composites with enhanced cell-matrix interactions as blood vessel endothelial layer scaffolds.

PubMed

Jiang, Yong-Chao; Jiang, Lin; Huang, An; Wang, Xiao-Feng; Li, Qian; Turng, Lih-Sheng

2017-02-01

During the fabrication of tissue engineering scaffolds and subsequent tissue regeneration, surface bioactivity is vital for cell adhesion, spreading, and proliferation, especially for endothelium dysfunction repair. In this paper, synthetic polymer polycaprolactone (PCL) was blended with natural polymer gelatin at four different weight ratios followed by crosslinking (i.e., 100:0, 70:30, 50:50, 30:70, labeled as PCL-C, P7G3-C, P5G5-C, and P3G7-C) to impart enhanced bioactivity and tunable mechanical properties. The PCL/gelatin blends were first dissolved in 2,2,2-trifluroethanol (TFE) and supplementary acetic acid (1% relative to TFE) solvent, electrospun, and then cross-linked to produce PBS-proof fibrous scaffolds. Scanning electron micrographs (SEM) indicated that fibers of each sample were smooth and homogeneous, with the fiber diameters increasing from 1.01±0.51μm to 1.61±0.46μm as the content of gelatin increased. While thermal resistance and crystallization of the blends were affected by the presence of gelatin, as reflected by differential scanning calorimetry (DSC) results, water contact angle (WCA) tests confirmed that the scaffold surfaces became more hydrophilic. Tensile tests showed that PCL-C and P7G3-C scaffolds had mechanical properties comparable to those of human coronary arteries. As for cytocompatibility, skeleton staining images showed that human mesenchymal stem cells (hMSCs) had more favorable binding sites on PCL/gelatin scaffolds than those on PCL scaffolds. Cell proliferation assays revealed that P7G3-C scaffolds could support the most number of hMSCs. The results of this study demonstrated the enhanced cell-matrix interactions and potential use of electrospun PCL/gelatin scaffolds in the tissue engineering field, especially in wound dressings and endothelium regeneration. Copyright © 2016 Elsevier B.V. All rights reserved.

Biodistribution of biodegradable polymeric nano-carriers loaded with busulphan and designed for multimodal imaging.

PubMed

Asem, Heba; Zhao, Ying; Ye, Fei; Barrefelt, Åsa; Abedi-Valugerdi, Manuchehr; El-Sayed, Ramy; El-Serafi, Ibrahim; Abu-Salah, Khalid M; Hamm, Jörg; Muhammed, Mamoun; Hassan, Moustapha

2016-12-19

Multifunctional nanocarriers for controlled drug delivery, imaging of disease development and follow-up of treatment efficacy are promising novel tools for disease diagnosis and treatment. In the current investigation, we present a multifunctional theranostic nanocarrier system for anticancer drug delivery and molecular imaging. Superparamagnetic iron oxide nanoparticles (SPIONs) as an MRI contrast agent and busulphan as a model for lipophilic antineoplastic drugs were encapsulated into poly (ethylene glycol)-co-poly (caprolactone) (PEG-PCL) micelles via the emulsion-evaporation method, and PEG-PCL was labelled with VivoTag 680XL fluorochrome for in vivo fluorescence imaging. Busulphan entrapment efficiency was 83% while the drug release showed a sustained pattern over 10 h. SPION loaded-PEG-PCL micelles showed contrast enhancement in T 2 *-weighted MRI with high r 2 * relaxivity. In vitro cellular uptake of PEG-PCL micelles labeled with fluorescein in J774A cells was found to be time-dependent. The maximum uptake was observed after 24 h of incubation. The biodistribution of PEG-PCL micelles functionalized with VivoTag 680XL was investigated in Balb/c mice over 48 h using in vivo fluorescence imaging. The results of real-time live imaging were then confirmed by ex vivo organ imaging and histological examination. Generally, PEG-PCL micelles were highly distributed into the lungs during the first 4 h post intravenous administration, then redistributed and accumulated in liver and spleen until 48 h post administration. No pathological impairment was found in the major organs studied. Thus, with loaded contrast agent and conjugated fluorochrome, PEG-PCL micelles as biodegradable and biocompatible nanocarriers are efficient multimodal imaging agents, offering high drug loading capacity, and sustained drug release. These might offer high treatment efficacy and real-time tracking of the drug delivery system in vivo, which is crucial for designing of an efficient drug delivery system.

Functional poly(ε-caprolactone)/chitosan dressings with nitric oxide-releasing property improve wound healing.

PubMed

Zhou, Xin; Wang, He; Zhang, Jimin; Li, Xuemei; Wu, Yifan; Wei, Yongzhen; Ji, Shenglu; Kong, Deling; Zhao, Qiang

2017-05-01

Wound healing dressings are increasingly needed clinically due to the large number of skin damage annually. Nitric oxide (NO) plays a key role in promoting wound healing, thus biomaterials with NO-releasing property receive increasing attention as ideal wound dressing. In present study, we prepared a novel functional wound dressing by combining electrospun poly(ε-caprolactone) (PCL) nonwoven mat with chitosan-based NO-releasing biomaterials (CS-NO). As-prepared PCL/CS-NO dressing released NO sustainably under the physiological conditions, which was controlled by the catalysis of β-galactosidase. In vivo wound healing characteristics were further evaluated on full-thickness cutaneous wounds in mice. Results showed that PCL/CS-NO wound dressings remarkably accelerated wound healing process through enhancing re-epithelialization and granulation formation and effectively improved the organization of regenerated tissues including epidermal-dermal junction, which could be ascribed to the pro-angiogenesis, immunomodulation, and enhanced collagen synthesis provided by the sustained release of NO. Therefore, PCL/CS-NO may be a promising candidate for wound dressings, especially for the chronic wound caused by the ischemia. Serious skin damage caused by trauma, surgery, burn or chronic disease has become one of the most serious clinical problems. Therefore, there is an increasing demand for ideal wound dressing that can improve wound healing. Due to the vital role of nitric oxide (NO), we developed a novel functional wound dressing by combining electrospun polycaprolactone (PCL) mat with NO-releasing biomaterial (CS-NO). The sustained release of NO from PCL/CS-NO demonstrated positive effects on wound healing, including pro-angiogenesis, immunomodulation, and enhanced collagen synthesis. Hence, wound healing process was remarkably accelerated and the organization of regenerated tissues was effectively improved as well. Taken together, PCL/CS-NO dressing may be a promising candidate for wound treatment, especially for the chronic wound caused by the ischemia. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Minimum Description Length Block Finder, a Method to Identify Haplotype Blocks and to Compare the Strength of Block Boundaries

PubMed Central

Mannila, H.; Koivisto, M.; Perola, M.; Varilo, T.; Hennah, W.; Ekelund, J.; Lukk, M.; Peltonen, L.; Ukkonen, E.

2003-01-01

We describe a new probabilistic method for finding haplotype blocks that is based on the use of the minimum description length (MDL) principle. We give a rigorous definition of the quality of a segmentation of a genomic region into blocks and describe a dynamic programming algorithm for finding the optimal segmentation with respect to this measure. We also describe a method for finding the probability of a block boundary for each pair of adjacent markers: this gives a tool for evaluating the significance of each block boundary. We have applied the method to the published data of Daly and colleagues. The results expose some problems that exist in the current methods for the evaluation of the significance of predicted block boundaries. Our method, MDL block finder, can be used to compare block borders in different sample sets, and we demonstrate this by applying the MDL-based method to define the block structure in chromosomes from population isolates. PMID:12761696

Minimum description length block finder, a method to identify haplotype blocks and to compare the strength of block boundaries.

PubMed

Mannila, H; Koivisto, M; Perola, M; Varilo, T; Hennah, W; Ekelund, J; Lukk, M; Peltonen, L; Ukkonen, E

2003-07-01

We describe a new probabilistic method for finding haplotype blocks that is based on the use of the minimum description length (MDL) principle. We give a rigorous definition of the quality of a segmentation of a genomic region into blocks and describe a dynamic programming algorithm for finding the optimal segmentation with respect to this measure. We also describe a method for finding the probability of a block boundary for each pair of adjacent markers: this gives a tool for evaluating the significance of each block boundary. We have applied the method to the published data of Daly and colleagues. The results expose some problems that exist in the current methods for the evaluation of the significance of predicted block boundaries. Our method, MDL block finder, can be used to compare block borders in different sample sets, and we demonstrate this by applying the MDL-based method to define the block structure in chromosomes from population isolates.

Preparation and Characterization of Hyaluronic Acid-Polycaprolactone Copolymer Micelles for the Drug Delivery of Radioactive Iodine-131 Labeled Lipiodol.

PubMed

Chen, Shih-Cheng; Yang, Ming-Hui; Chung, Tze-Wen; Jhuang, Ting-Syuan; Yang, Jean-Dean; Chen, Ko-Chin; Chen, Wan-Jou; Huang, Ying-Fong; Jong, Shiang-Bin; Tsai, Wan-Chi; Lin, Po-Chiao; Tyan, Yu-Chang

2017-01-01

Micelles, with the structure of amphiphilic molecules including a hydrophilic head and a hydrophobic tail, are recently developed as nanocarriers for the delivery of drugs with poor solubility. In addition, micelles have shown many advantages, such as enhanced permeation and retention (EPR) effects, prolonged circulation times, and increased endocytosis through surface modification. In this study, we measured the critical micelle concentrations, diameters, stability, and cytotoxicity and the cell uptake of micelles against hepatic cells with two kinds of hydrophilic materials: PEG-PCL and HA-g-PCL. We used 131 I as a radioactive tracer to evaluate the stability, drug delivery, and cell uptake activity of the micelles. The results showed that HA-g-PCL micelles exhibited higher drug encapsulation efficiency and stability in aqueous solutions. In addition, the 131 I-lipiodol loaded HA-g-PCL micelles had better affinity and higher cytotoxicity compared to HepG2 cells.

Biodegradable Hybrid Stomatocyte Nanomotors for Drug Delivery

PubMed Central

2017-01-01

We report the self-assembly of a biodegradable platinum nanoparticle-loaded stomatocyte nanomotor containing both PEG-b-PCL and PEG-b-PS as a potential candidate for anticancer drug delivery. Well-defined stomatocyte structures could be formed even after incorporation of 50% PEG-b-PCL polymer. Demixing of the two polymers was expected at high percentage of semicrystalline poly(ε-caprolactone) (PCL), resulting in PCL domain formation onto the membrane due to different properties of two polymers. The biodegradable motor system was further shown to move directionally with speeds up to 39 μm/s by converting chemical fuel, hydrogen peroxide, into mechanical motion as well as rapidly delivering the drug to the targeted cancer cell. Uptake by cancer cells and fast doxorubicin drug release was demonstrated during the degradation of the motor system. Such biodegradable nanomotors provide a convenient and efficient platform for the delivery and controlled release of therapeutic drugs. PMID:28187254

Use of the Personality Assessment Inventory to assess psychopathy in offender populations.

PubMed

Edens, J F; Hart, S D; Johnson, D W; Johnson, J K; Olver, M E

2000-06-01

The authors investigated the validity of the Antisocial Features (ANT) scale of the Personality Assessment Inventory (PAI; L. C. Morey, 1991) with respect to assessments of psychopathy in 2 offender samples. Study 1 included 46 forensic psychiatric inpatients who were administered the Screening Version of the Hare Psychopathy Checklist (PCL:SV; S. D. Hart, D. N. Cox, & R. D. Hare, 1995). In Study 2, 55 sex offenders were administered the Hare Psychopathy Checklist--Revised (PCL-R; R. D. Hare, 1991). ANT scores correlated highly with the PCL:SV total score (r = .54) and moderately with the PCL-R total score (r = .40). ANT tapped primarily behavioral symptoms of psychopathy rather than interpersonal and affective symptoms. Also, ANT had low to moderate diagnostic efficiency regarding diagnoses of psychopathy, suggesting that it may be better used as a dimensional rather than categorical measure of this construct.

Hydroxyapatite-armored poly(ε-caprolactone) microspheres and hydroxyapatite microcapsules fabricated via a Pickering emulsion route.

PubMed

Fujii, Syuji; Okada, Masahiro; Nishimura, Taiki; Maeda, Hayata; Sugimoto, Tatsuya; Hamasaki, Hiroyuki; Furuzono, Tsutomu; Nakamura, Yoshinobu

2012-05-15

Hydroxyapatite (HAp) nanoparticle-armored poly(ε-caprolactone) (PCL) microspheres were fabricated via a "Pickering-type" emulsion solvent evaporation method in the absence of any molecular surfactants. It was clarified that the interaction between carbonyl/carboxylic acid groups of PCL and the HAp nanoparticles at an oil-water interface played a crucial role in the preparation of the stable Pickering-type emulsions and the HAp nanoparticle-armored microspheres. The HAp nanoparticle-armored PCL microspheres were characterized in terms of size, size distribution, morphology, and chemical compositions using scanning electron microscopy, laser diffraction, energy dispersive X-ray microanalysis, and thermogravimetric analysis. The presence of HAp nanoparticles at the surface of the microspheres was confirmed by scanning electron microscopy and energy dispersive X-ray microanalysis. Pyrolysis of the PCL cores led to the formation of the corresponding HAp hollow microcapsules. Copyright © 2012 Elsevier Inc. All rights reserved.

Thermosetting epoxy resin/thermoplastic system with combined shape memory and self-healing properties

NASA Astrophysics Data System (ADS)

Yao, Yongtao; Wang, Jingjie; Lu, Haibao; Xu, Ben; Fu, Yongqing; Liu, Yanju; Leng, Jinsong

2016-01-01

A novel and facile strategy was proposed to construct a thermosetting/thermoplastic system with both shape memory and self-healing properties based on commercial epoxy resin and poly(ɛ-caprolactone)-PCL. Thermoplastic material is capable of re-structuring and changing the stiffness/modulus when the temperature is above melting temperature. PCL microfiber was used as a plasticizer in epoxy resin-based blends, and served as a ‘hard segment’ to fix a temporary shape of the composites during shape memory cycles. In this study, the electrospun PCL membrane with a porous network structure enabled a homogenous PCL fibrous distribution and optimized interaction between fiber and epoxy resin. The self-healing capability is achieved by phase transition during curing of the composites. The mechanism of the shape memory effect of the thermosetting (rubber)/thermoplastic composite is attributed to the structural design of the thermoplastic network inside the thermosetting resin/rubber matrix.

Broadband IR polarizing beam splitter using a subwavelength-structured one-dimensional photonic-crystal layer embedded in a high-index prism.

PubMed

Khanfar, H K; Azzam, R M A

2009-09-20

An iterative procedure for the design of a polarizing beam splitter (PBS) that uses a form-birefringent, subwavelength-structured, one-dimensional photonic-crystal layer (SWS 1-D PCL) embedded in a high-index cubical prism is presented. The PBS is based on index matching and total transmission for the p polarization and total internal reflection for the s polarization at the prism-PCL interface at 45 degrees angle of incidence. A high extinction ratio in reflection (>50 dB) over the 4-12 microm IR spectral range is achieved using a SWS 1-D PCL of ZnTe embedded in a ZnS cube within an external field of view of +/-6.6 degrees and in the presence of grating filling factor errors of up to +/-10%. Comparable results, but with wider field of view, are also obtained with a Ge PCL embedded in a Si prism.

Nanoparticles obtained by confined impinging jet mixer: poly(lactide-co-glycolide) vs. Poly-ε-caprolactone.

PubMed

Turino, Ludmila N; Stella, Barbara; Dosio, Franco; Luna, Julio A; Barresi, Antonello A

2018-06-01

This paper is focused on the production and characterization of polymeric nanoparticles obtained by nanoprecipitation. The method consisted of using a confined impinging jet mixer (CIJM), circumventing high-energy equipment. Differences between the use of poly-ε-caprolactone (PCL) and poly(lactide-co-glycolide) (PLGA) as concerns particle mean size, zeta potential, and broad-spectrum antibiotic florfenicol entrapment were investigated. Other analyzed variables were polymer concentration, solvent, and anti-solvent flow rates, and antibiotic initial concentration. To our knowledge, no data were found related to PLGA and PCL nanoparticles comparison using CIJM. Also, florfenicol encapsulation within PCL or PLGA nanoparticles by nanoprecipitation has not been reported yet. The complexity of the nanoprecipitation phenomena has been confirmed, with many relevant variables involved in particles formation. PLGA resulted in smaller and more stable nanoparticles with higher entrapping of florfenicol than PCL.

Validity of Factors of the Psychopathy Checklist–Revised in Female Prisoners

PubMed Central

Kennealy, Patrick J.; Hicks, Brian M.; Patrick, Christopher J.

2008-01-01

The validity of the Psychopathy Checklist–Revised (PCL-R) has been examined extensively in men, but its validity for women remains understudied. Specifically, the correlates of the general construct of psychopathy and its components as assessed by PCL-R total, factor, and facet scores have yet to be examined in depth. Based on previous research conducted with male offenders, a large female inmate sample was used to examine the patterns of relations between total, factor, and facet scores on the PCL-R and various criterion variables. These variables include ratings of psychopathy based on Cleckley’s criteria, symptoms of antisocial personality disorder, and measures of substance use and abuse, criminal behavior, institutional misconduct, interpersonal aggression, normal range personality, intellectual functioning, and social background variables. Results were highly consistent with past findings in male samples and provide further evidence for the construct validity of the PCL-R two-factor and four-facet models across genders. PMID:17986651

Lateral thrust of anterior cruciate ligament-insufficient knees and posterior cruciate ligament-insufficient knees.

PubMed

Yoshimura, Ichiro; Naito, Masatoshi; Zhang, Jingfan

2002-01-01

Leaving anterior cruciate ligament (ACL) insufficiency and posterior cruciate ligament (PCL) insufficiency untreated frequently leads to osteoarthritis (OA). The purpose of this study was to evaluate dynamically the lateral thrust of ACL-insufficient knees and PCL-insufficient knees, and from the findings investigate the relationship between cruciate ligament insufficiency and OA occurrence. An acceleration sensor was attached to the affected and control anterior tibial tubercles, acting in medial-lateral and perpendicular directions. The lateral thrust immediately after heel strike was measured continuously by a telemeter under stabilised walking conditions. When compared to the contralateral healthy knee, the peak value of lateral acceleration immediately after heel strike was significantly larger in the ACL-insufficient knee; and lateral thrust was increased, but not significantly, in the PCL-insufficient knee. Given that lateral thrust of the knee during walking increases due to ACL or PCL injury, it may be a principal contributor to OA progression.

Reversible TAD Chemistry as a Convenient Tool for the Design of (Re)processable PCL-Based Shape-Memory Materials.

PubMed

Defize, Thomas; Riva, Raphaël; Thomassin, Jean-Michel; Alexandre, Michaël; Herck, Niels Van; Prez, Filip Du; Jérôme, Christine

2017-01-01

A chemically cross-linked but remarkably (re)processable shape-memory polymer (SMP) is designed by cross-linking poly(ε-caprolactone) (PCL) stars via the efficient triazolinedione click chemistry, based on the very fast and reversible Alder-ene reaction of 1,2,4-triazoline-3,5-dione (TAD) with indole compounds. Typically, a six-arm star-shaped PCL functionalized by indole moieties at the chain ends is melt-blended with a bisfunctional TAD, directly resulting in a cross-linked PCL-based SMP without the need of post-curing treatment. As demonstrated by the stress relaxation measurement, the labile character of the TAD-indole adducts under stress allows for the solid-state plasticity reprocessing of the permanent shape at will by compression molding of the raw cross-linked material, while keeping excellent shape-memory properties. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Impregnation of Ibuprofen into Polycaprolactone using supercritical carbon dioxide

NASA Astrophysics Data System (ADS)

Yoganathan, Roshan; Mammucari, Raffaella; Foster, Neil R.

2010-03-01

Polycaprolactone (PCL) is a Food and Drug Administration (FDA) approved biodegradable polyester used in tissue engineering applications. Ibuprofen is an anti-inflammatory drug which has good solubility in supercritical CO2 (SCCO2). The solubility of CO2 in PCL allows for the impregnation of CO2-soluble therapeutic agents into the polymer via a supercritical fluid (SCF) process. Polymers impregnated with bio-active compounds are highly desired for medical implants and controlled drug delivery. In this study, the use of CO2 to impregnate PCL with ibuprofen was investigated. The effect of operating conditions on the impregnation of ibuprofen into PCL was investigated over two pressure and two temperature levels, 150bar and 200bar, 35°C and 40 °C, respectively. Polycaprolactone with drug-loadings as high as 27% w/w were obtained. Impregnated samples exhibited controlled drug release profiles over several days.

Well-defined block copolymers for gene delivery to dendritic cells: probing the effect of polycation chain-length.

PubMed

Tang, Rupei; Palumbo, R Noelle; Nagarajan, Lakshmi; Krogstad, Emily; Wang, Chun

2010-03-03

The development of safe and efficient polymer carriers for DNA vaccine delivery requires mechanistic understanding of structure-function relationship of the polymer carriers and their interaction with antigen-presenting cells. Here we have synthesized a series of diblock copolymers with well-defined chain-length using atom transfer radical polymerization and characterized the influence of polycation chain-length on the physico-chemical properties of the polymer/DNA complexes as well as the interaction with dendritic cells. The copolymers consist of a hydrophilic poly(ethylene glycol) block and a cationic poly(aminoethyl methacrylate) (PAEM) block. The average degree of polymerization (DP) of the PAEM block was varied among 19, 39, and 75, with nearly uniform distribution. With increasing PAEM chain-length, polyplexes formed by the diblock copolymers and plasmid DNA had smaller average particle size and showed higher stability against electrostatic destabilization by salt and heparin. The polymers were not toxic to mouse dendritic cells (DCs) and only displayed chain-length-dependent toxicity at a high concentration (1mg/mL). In vitro gene transfection efficiency and polyplex uptake in DCs were also found to correlate with chain-length of the PAEM block with the longer polymer chain favoring transfection and cellular uptake. The polyplexes induced a modest up-regulation of surface markers for DC maturation that was not significantly dependent on PAEM chain-length. Finally, the polyplex prepared from the longest PAEM block (DP of 75) achieved an average of 20% enhancement over non-condensed anionic dextran in terms of uptake by DCs in the draining lymph nodes 24h after subcutaneous injection into mice. Insights gained from studying such structurally well-defined polymer carriers and their interaction with dendritic cells may contribute to improved design of practically useful DNA vaccine delivery systems. Copyright 2009 Elsevier B.V. All rights reserved.

High-efficiency Gaussian key reconciliation in continuous variable quantum key distribution

NASA Astrophysics Data System (ADS)

Bai, ZengLiang; Wang, XuYang; Yang, ShenShen; Li, YongMin

2016-01-01

Efficient reconciliation is a crucial step in continuous variable quantum key distribution. The progressive-edge-growth (PEG) algorithm is an efficient method to construct relatively short block length low-density parity-check (LDPC) codes. The qua-sicyclic construction method can extend short block length codes and further eliminate the shortest cycle. In this paper, by combining the PEG algorithm and qua-si-cyclic construction method, we design long block length irregular LDPC codes with high error-correcting capacity. Based on these LDPC codes, we achieve high-efficiency Gaussian key reconciliation with slice recon-ciliation based on multilevel coding/multistage decoding with an efficiency of 93.7%.

Manipulating the structure and mechanical properties of thermoplastic polyurethane/polycaprolactone hybrid small diameter vascular scaffolds fabricated via electrospinning using an assembled rotating collector.

PubMed

Mi, Hao-Yang; Jing, Xin; Yu, Emily; Wang, Xiaofeng; Li, Qian; Turng, Lih-Sheng

2018-02-01

The success of blood vessel transplants with vascular scaffolds (VSs) highly depends on their structure and mechanical properties. The fabrication of small diameter vascular scaffolds (SDVSs) mimicking the properties of native blood vessels has been a challenge. Herein, we propose a facile method to fabricate thermoplastic polyurethane (TPU)/polycaprolactone (PCL) hybrid SDVSs via electrospinning using a modified rotating collector. By varying the ratio between the TPU and the PCL, and changing the electrospinning volume, SDVSs with a wavy configuration and different properties could be obtained. Detailed investigation revealed that certain TPU/PCL hybrid SDVSs closely resembled the mechanical behaviors of blood vessels due to the presence of a wavy region and the combination of flexible TPU and rigid PCL, which mimicked the properties of elastin and collagen in blood vessels. The fabricated TPU/PCL SDVSs achieved lumen diameters of 1-3mm, wall thicknesses of 100-570µm, circumferential moduli of 1-6MPa, ultimate strengths of 2-8MPa, over 250% elongation-at-break values, toe regions of 5.3-9.4%, high recoverability, and compliances close to those of human veins. Moreover, these TPU/PCL SDVSs possessed sufficient suture retention strength and burst pressure to fulfill transplantation requirements and maintain normal blood flow. Human endothelial cell culture revealed good biocompatibility of the scaffolds, and cells were able to grow on the inner surface of the tubular scaffolds, indicating promising prospects for use as tissue-engineered vascular grafts. Copyright © 2017 Elsevier Ltd. All rights reserved.

An improved OpenSim gait model with multiple degrees of freedom knee joint and knee ligaments.

PubMed

Xu, Hang; Bloswick, Donald; Merryweather, Andrew

2015-08-01

Musculoskeletal models are widely used to investigate joint kinematics and predict muscle force during gait. However, the knee is usually simplified as a one degree of freedom joint and knee ligaments are neglected. The aim of this study was to develop an OpenSim gait model with enhanced knee structures. The knee joint in this study included three rotations and three translations. The three knee rotations and mediolateral translation were independent, with proximodistal and anteroposterior translations occurring as a function of knee flexion/extension. Ten elastic elements described the geometrical and mechanical properties of the anterior and posterior cruciate ligaments (ACL and PCL), and the medial and lateral collateral ligaments (MCL and LCL). The three independent knee rotations were evaluated using OpenSim to observe ligament function. The results showed that the anterior and posterior bundles of ACL and PCL (aACL, pACL and aPCL, pPCL) intersected during knee flexion. The aACL and pACL mainly provided force during knee flexion and adduction, respectively. The aPCL was slack throughout the range of three knee rotations; however, the pPCL was utilised for knee abduction and internal rotation. The LCL was employed for knee adduction and rotation, but was slack beyond 20° of knee flexion. The MCL bundles were mainly used during knee adduction and external rotation. All these results suggest that the functions of knee ligaments in this model approximated the behaviour of the physical knee and the enhanced knee structures can improve the ability to investigate knee joint biomechanics during various gait activities.

Physical examination tests for the diagnosis of posterior cruciate ligament rupture: a systematic review.

PubMed

Kopkow, Christian; Freiberg, Alice; Kirschner, Stephan; Seidler, Andreas; Schmitt, Jochen

2013-11-01

Systematic literature review. To summarize and evaluate research on the accuracy of physical examination tests for diagnosis of posterior cruciate ligament (PCL) tear. Rupture of the PCL is a severe knee injury that can lead to delayed rehabilitation, instability, or chronic knee pathologies. To our knowledge, there is currently no systematic review of studies on the diagnostic accuracy of clinical examination tests to evaluate the integrity of the PCL. A comprehensive systematic literature search was conducted in MEDLINE from 1946, Embase from 1974, and the Allied and Complementary Medicine Database from 1985 until April 30, 2012. Studies were considered eligible if they compared the results of physical examination tests performed in the context of a PCL physical examination to those of a reference standard (arthroscopy, arthrotomy, magnetic resonance imaging). Methodological quality assessment was performed by 2 independent reviewers using the revised version of the Quality Assessment of Diagnostic Accuracy Studies (QUADAS-2) tool. The search strategy revealed 1307 articles, of which 11 met the inclusion criteria for this review. In these studies, 11 different physical examination tests were identified. Due to differences in study types, different patient populations, and methodological quality, meta-analysis was not indicated. Presently, most physical examination tests have not been evaluated sufficiently enough to be confident in their ability to either confirm or rule out a PCL tear. The diagnostic accuracy of physical examination tests to assess the integrity of the PCL is largely unknown. There is a strong need for further research in this area. Level of Evidence Diagnosis, level 3a.

Enhanced biocompatibility and osteogenic potential of mesoporous magnesium silicate/polycaprolactone/wheat protein composite scaffolds

PubMed Central

Kang, Yun Gyeong; Wei, Jie; Shin, Ji Won; Wu, Yan Ru; Su, Jiacan; Park, Young Shik; Shin, Jung-Woog

2018-01-01

Background Successful bone tissue engineering using scaffolds is primarily dependent on the properties of the scaffold, including biocompatibility, highly interconnected porosity, and mechanical integrity. Methods In this study, we propose new composite scaffolds consisting of mesoporous magnesium silicate (m_MS), polycaprolactone (PCL), and wheat protein (WP) manufactured by a rapid prototyping technique to provide a micro/macro porous structure. Experimental groups were set based on the component ratio: (1) WP0% (m_MS:PCL:WP =30:70:0 weight per weight; w/w); (2) WP15% (m_MS:PCL:WP =30:55:15 w/w); (3) WP30% (m_MS:PCL:WP =30:40:30 w/w). Results Evaluation of the properties of fabricated scaffolds indicated that increasing the amount of WP improved the surface hydrophilicity and biodegradability of m_MS/PCL/WP composites, while reducing the mechanical strength. Moreover, experiments were performed to confirm the biocompatibility and osteogenic differentiation of human mesenchymal stem cells (MSCs) according to the component ratio of the scaffold. The results confirmed that the content of WP affects proliferation and osteogenic differentiation of MSCs. Based on the last day of the experiment, ie, the 14th day, the proliferation based on the amount of DNA was the best in the WP30% group, but all of the markers measured by PCR were the most expressed in the WP15% group. Conclusion These results suggest that the m_MS/PCL/WP composite is a promising candidate for use as a scaffold in cell-based bone regeneration. PMID:29520139

Subcomponents of Psychopathy have Opposing Correlations with Punishment Judgments

PubMed Central

Borg, Jana Schaich; Kahn, Rachel E.; Sinnott-Armstrong, Walter; Kurzban, Robert; Robinson, Paul H.; Kiehl, Kent A.

2013-01-01

Psychopathy research is plagued by an enigma: Psychopaths reliably act immorally, but they also accurately report whether an action is morally wrong. The current study revealed that cooperative suppressor effects and conflicting subsets of personality traits within the construct of psychopathy might help explain this conundrum. Among a sample of adult male offenders (n = 100) who ranked deserved punishment of crimes, Psychopathy Checklist-Revised (PCL-R) total scores were not linearly correlated with deserved punishment task performance. However, these null results masked significant opposing associations between task performance and factors of psychopathy: the PCL-R Interpersonal/Affective (i.e. manipulative and callous) factor was positively associated with task performance, while the PCL-R Social Deviance (i.e. impulsive and antisocial) factor was simultaneously negatively associated with task performance. Importantly, these relationships were qualified by a significant interaction where the Interpersonal/Affective traits were positively associated with task performance when Social Deviance traits were high, but Social Deviance traits were negatively associated with task performance when Interpersonal/Affective traits were low. This interaction helped reveal a significant non-linear relationship between PCL-R total scores and task performance such that individuals with very low or very high PCL-R total scores performed better than those with middle-range PCL-R total scores. These results may explain the enigma of why individuals with very high psychopathic traits, but not other groups of anti-social individuals, usually have normal moral judgment in laboratory settings, but still behave immorally, especially in contexts where Social Deviance traits have strong influence. PMID:23834639

Combinatorial Polymer Matrices Enhance In Vitro Maturation of Human Induced Pluripotent Cell Cell-Derived Cardiomyocytes

PubMed Central

Chun, Young Wook; Balikov, Daniel A.; Feaster, Tromondae K.; Williams, Charles H.; Sheng, Calvin C.; Lee, Jung-Bok; Boire, Timothy C.; Neely, M. Diana; Bellan, Leon M.; Ess, Kevin C.; Bowman, Aaron B.; Sung, Hak-Joon; Hong, Charles C.

2015-01-01

Cardiomyocytes derived from human induced pluripotent stem cells (iPSC-CMs) hold great promise for modeling human heart diseases. However, iPSC-CMs studied to date resemble immature embryonic myocytes and therefore do not adequately recapitulate native adult cardiomyocyte phenotypes. Since extracellular matrix plays an essential role in heart development and maturation in vivo, we sought to develop a synthetic culture matrix that could enhance functional maturation of iPSC-CMs in vitro. In this study, we employed a library of combinatorial polymers comprising of three functional subunits - poly-ε-caprolacton (PCL), polyethylene glycol (PEG), and carboxylated PCL (cPCL) - as synthetic substrates for culturing human iPSC-CMs. Of these, iPSC-CMs cultured on 4%PEG-96%PCL (each % indicates the corresponding molar ratio) exhibit the greatest contractility and mitochondrial function. These functional enhancements are associated with increased expression of cardiac myosin light chain-2v, cardiac troponin I and integrin alpha-7. Importantly, iPSC-CMs cultured on 4%PEG-95%PCL demonstrate troponin I (TnI) isoform switch from the fetal slow skeletal TnI (ssTnI) to the postnatal cardiac TnI (cTnI), the first report of such transition in vitro. Finally, culturing iPSC-CMs on 4%PEG-96%PCL also significantly increased expression of genes encoding intermediate filaments known to transduce integrin-mediated mechanical signals to the myofilaments. In summary, our study demonstrates that synthetic culture matrices engineered from combinatorial polymers can be utilized to promote in vitro maturation of human iPSC-CMs through the engagement of critical matrix-integrin interactions. PMID:26204225

Double hydrophilic block copolymer controlled growth and self-assembly of CaCO3 multilayered structures at the air/water interface.

PubMed

Gao, Yun-Xiang; Yu, Shu-Hong; Guo, Xiao-Hui

2006-07-04

Double hydrophilic block copolymers PEG-b-PEI-linear with different PEI block lengths have been examined for CaCO3 mineralization at the air/water interface. The results demonstrated that either PEI length or the solution acidity had a significant influence on the morphogenesis of vaterite crystals at the air/water interface. A possible mechanism for the stratification of CaCO3 vaterite crystals has been proposed. Increasing either PEI length or the initial pH value of the solution will decrease the density of the PEG block anchored on the binding interface and result in exposing more space as binding interface to solution and favoring the subnucleation and stratification growth on the polymer-CaCO3 interface. In contrast, higher density of PEG blocks will stabilize the growing crystals more efficiently and inhibit subnucleation on the polymer-CaCO3 interface, and thus prevent the formation of stratified structures. This study provides an example that it is possible to access morphogenesis of calcium carbonate structures by a combination of a block copolymer with the air/water interface.

Dynamic photoinduced realignment processes in photoresponsive block copolymer films: effects of the chain length and block copolymer architecture.

PubMed

Sano, Masami; Shan, Feng; Hara, Mitsuo; Nagano, Shusaku; Shinohara, Yuya; Amemiya, Yoshiyuki; Seki, Takahiro

2015-08-07

A series of block copolymers composed of an amorphous poly(butyl methacrylate) (PBMA) block connected with an azobenzene (Az)-containing liquid crystalline (PAz) block were synthesized by changing the chain length and polymer architecture. With these block copolymer films, the dynamic realignment process of microphase separated (MPS) cylinder arrays of PBMA in the PAz matrix induced by irradiation with linearly polarized light was studied by UV-visible absorption spectroscopy, and time-resolved grazing incidence small angle X-ray scattering (GI-SAXS) measurements using a synchrotron beam. Unexpectedly, the change in the chain length hardly affected the realignment rate. In contrast, the architecture of the AB-type diblock or the ABA-type triblock essentially altered the realignment feature. The strongly cooperative motion with an induction period before realignment was characteristic only for the diblock copolymer series, and the LPL-induced alignment change immediately started for triblock copolymers and the PAz homopolymer. Additionally, a marked acceleration in the photoinduced dynamic motions was unveiled in comparison with a thermal randomization process.

Bioactive Cellulose Nanocrystal Reinforced 3D Printable Poly(epsilon-caprolactone) Nanocomposite for Bone Tissue Engineering

NASA Astrophysics Data System (ADS)

Hong, Jung Ki

Polymeric bone scaffolds are a promising tissue engineering approach for the repair of critical-size bone defects. Porous three-dimensional (3D) scaffolds play an essential role as templates to guide new tissue formation. However, there are critical challenges arising from the poor mechanical properties and low bioactivity of bioresorbable polymers, such as poly(a-caprolactone) (PCL) in bone tissue engineering applications. This research investigates the potential use of cellulose nanocrystals (CNCs) as multi-functional additives that enhance the mechanical properties and increase the biomineralization rate of PCL. To this end, an in vitro biomineralization study of both sulfuric acid hydrolyzed- CNCs (SH-CNCs) and surface oxidized-CNCs (SO-CNCs) has been performed in simulated body fluid in order to evaluate the bioactivity of the surface functional groups, sulfate and carboxyl groups, respectively. PCL nanocomposites were prepared with different SO-CNC contents and the chemical/physical properties of the nanocomposites were analyzed. 3D porous scaffolds with fully interconnected pores and well-controlled pore sizes were fabricated from the PCL nanocomposites with a 3D printer. The mechanical stability of the scaffolds were studied using creep test under dry and submersion conditions. Lastly, the biocompatibility of CNCs and 3D printed porous scaffolds were assessed in vitro.. The carboxyl groups on the surface of SO-CNCs provided a significantly improved calcium ion binding ability which could play an important role in the biomineralization (bioactivity) by induction of mineral formation for bone tissue engineering applications. In addition, the mechanical properties of porous PCL nanocomposite scaffolds were pronouncedly reinforced by incorporation of SO-CNCs. Both the compressive modulus and creep resistance of the PCL scaffolds were enhanced either in dry or in submersion conditions at 37 °C. Lastly, the biocompatibility study demonstrated that both the CNCs and material fabrication processes (e.g., PCL nanocomposites and 3D printing) were not toxic to the preosteoblasts (MC3T3 cells). Also, the SO-CNCs showed a positive effect on biomineralization of PCL scaffolds (i.e., accelerated calcium or mineral deposits on the surface of the scaffolds) during in vitro study. Overall, the SO-CNCs could play a critical role in the development of scaffold materials as a potential candidate for reinforcing nanofillers in bone tissue engineering applications.

Lateralization of the Tibial Tubercle in Recurrent Patellar Dislocation: Verification Using Multiple Methods to Evaluate the Tibial Tubercle.

PubMed

Tensho, Keiji; Shimodaira, Hiroki; Akaoka, Yusuke; Koyama, Suguru; Hatanaka, Daisuke; Ikegami, Shota; Kato, Hiroyuki; Saito, Naoto

2018-05-02

The tibial tubercle deviation associated with recurrent patellar dislocation (RPD) has not been studied sufficiently. New methods of evaluation were used to verify the extent of tubercle deviation in a group with patellar dislocation compared with that in a control group, the frequency of patients who demonstrated a cutoff value indicating that tubercle transfer was warranted on the basis of the control group distribution, and the validity of these methods of evaluation for diagnosing RPD. Sixty-six patients with a history of patellar dislocation (single in 19 [SPD group] and recurrent in 47 [RPD group]) and 66 age and sex-matched controls were analyzed with the use of computed tomography (CT). The tibial tubercle-posterior cruciate ligament (TT-PCL) distance, TT-PCL ratio, and tibial tubercle lateralization (TTL) in the SPD and RPD groups were compared with those in the control group. Cutoff values to warrant 10 mm of transfer were based on either the minimum or -2SD (2 standard deviations below the mean) value in the control group, and the prevalences of patients in the RPD group with measurements above these cutoff values were calculated. The area under the curve (AUC) in receiver operating characteristic (ROC) curve analysis was used to assess the effectiveness of the measurements as predictors of RPD. The mean TT-PCL distance, TT-PCL ratio, and TTL were all significantly greater in the RPD group than in the control group. The numbers of patients in the RPD group who satisfied the cutoff criteria when they were based on the minimum TT-PCL distance, TT-PCL ratio, and TTL in the control group were 11 (23%), 7 (15%), and 6 (13%), respectively. When the cutoff values were based on the -2SD values in the control group, the numbers of patients were 8 (17%), 6 (13%), and 0, respectively. The AUC of the ROC curve for TT-PCL distance, TT-PCL ratio, and TTL was 0.66, 0.72, and 0.72, respectively. The extent of TTL in the RPD group was not substantial, and the percentages of patients for whom 10 mm of medial transfer was indicated were small. Prognostic Level III. See Instructions for Authors for a complete description of levels of evidence.

Hyaluronic acid coated poly-epsilon-caprolactone nanospheres deliver high concentrations of cyclosporine A into the cornea.

PubMed

Yenice, Irem; Mocan, Mehmet C; Palaska, Erhan; Bochot, Amélie; Bilensoy, Erem; Vural, Imran; Irkeç, Murat; Hincal, A Atilla

2008-09-01

The objective of this study was to determine cyclosporine A (Cy A) levels in ocular tissues and fluids after topical administration of poly-epsilon-caprolactone (PCL)/benzalkonium chloride (BKC) nanospheres and hyaluronic acid (HA) coated PCL/BKC nanospheres onto healthy rabbit corneas. Nanospheres were prepared by nanoprecipitation and purified by gradient-rate centrifugation. Cy A (0.1%) in either castor oil solution (group 1), PCL/BKC nanosphere formulation (group 2) or HA coated PCL/BKC nanosphere formulation (group 3) was instilled onto rabbit corneas. Tear samples were adsorbed onto Schirmer tear strips. Cy A concentrations of fluid (blood, aqueous humor, tear) and specimen extracts (cornea, conjunctiva, iris/ciliary body) were determined by high performance liquid chromatography-mass spectrometry (LC-MS). The mean corneal Cy A concentration obtained at 0.5, 1, 2, 4, 8 and 24h following instillation of the formulations ranged between 0.12 and 1.2 ng/mg tissue for group 1, 5.9-15.5 ng/mg tissue for group 2 and 11.4-23.0 ng/mg for group 3 (one-way analysis of variance (ANOVA) and pairwise tests (SNK (Student-Newman-Keuls) and Tukey); p<0.05). Conjunctival Cy A levels of group 2 and 3 were not significantly different at any of the time points tested. However, there was a significant difference between Cy A concentration of castor oil formulation and that of PCL/BKC nanosphere formulation at 1 and 8h (p<0.05). The mean iris/ciliary body concentrations obtained with the three formulations were not significantly different at any time point with the exception of group 2 levels being higher than those of groups 1 and 3 at 1h (p<0.05). The lowest ocular tear Cy A concentrations (16-114 ng/ml) were found following the instillation of HA coated PCL/BKC nanoparticles (group 3) during the time period tested. Cy A loaded PCL/BKC and HA coated PCL/BKC nanospheres are able to achieve high levels of Cy A in the cornea that is 10-15-fold higher than that is achieved with Cy A solution in castor oil. Nanosphere formulation and HA may play an important role in delivering high levels of cyclosporine A into the cornea.

Loading Patterns of the Posterior Cruciate Ligament in the Healthy Knee: A Systematic Review

PubMed Central

List, Renate; Oberhofer, Katja; Fucentese, Sandro F.; Snedeker, Jess G.; Taylor, William R.

2016-01-01

Background The posterior cruciate ligament (PCL) is the strongest ligament of the knee, serving as one of the major passive stabilizers of the tibio-femoral joint. However, despite a number of experimental and modelling approaches to understand the kinematics and kinetics of the ligament, the normal loading conditions of the PCL and its functional bundles are still controversially discussed. Objectives This study aimed to generate science-based evidence for understanding the functional loading of the PCL, including the anterolateral and posteromedial bundles, in the healthy knee joint through systematic review and statistical analysis of the literature. Data sources MEDLINE, EMBASE and CENTRAL Eligibility criteria for selecting studies Databases were searched for articles containing any numerical strain or force data on the healthy PCL and its functional bundles. Studied activities were as follows: passive flexion, flexion under 100N and 134N posterior tibial load, walking, stair ascent and descent, body-weight squatting and forward lunge. Method Statistical analysis was performed on the reported load data, which was weighted according to the number of knees tested to extract average strain and force trends of the PCL and identify deviations from the norms. Results From the 3577 articles retrieved by the initial electronic search, only 66 met all inclusion criteria. The results obtained by aggregating data reported in the eligible studies indicate that the loading patterns of the PCL vary with activity type, knee flexion angle, but importantly also the technique used for assessment. Moreover, different fibres of the PCL exhibit different strain patterns during knee flexion, with higher strain magnitudes reported in the anterolateral bundle. While during passive flexion the posteromedial bundle is either lax or very slightly elongated, it experiences higher strain levels during forward lunge and has a synergetic relationship with the anterolateral bundle. The strain patterns obtained for virtual fibres that connect the origin and insertion of the bundles in a straight line show similar trends to those of the real bundles but with different magnitudes. Conclusion This review represents what is now the best available understanding of the biomechanics of the PCL, and may help to improve programs for injury prevention, diagnosis methods as well as reconstruction and rehabilitation techniques. PMID:27880849

Optimization of Blocked Designs in fMRI Studies

ERIC Educational Resources Information Center

Maus, Barbel; van Breukelen, Gerard J. P.; Goebel, Rainer; Berger, Martijn P. F.

2010-01-01

Blocked designs in functional magnetic resonance imaging (fMRI) are useful to localize functional brain areas. A blocked design consists of different blocks of trials of the same stimulus type and is characterized by three factors: the length of blocks, i.e., number of trials per blocks, the ordering of task and rest blocks, and the time between…

ZResponse to selection, heritability and genetic correlations between body weight and body size in Pacific white shrimp, Litopenaeus vannamei

NASA Astrophysics Data System (ADS)

Andriantahina, Farafidy; Liu, Xiaolin; Huang, Hao; Xiang, Jianhai

2012-03-01

To quantify the response to selection, heritability and genetic correlations between weight and size of Litopenaeus vannamei, the body weight (BW), total length (TL), body length (BL), first abdominal segment depth (FASD), third abdominal segment depth (TASD), first abdominal segment width (FASW), and partial carapace length (PCL) of 5-month-old parents and of offspnng were measured by calculating seven body measunngs of offspnng produced by a nested mating design. Seventeen half-sib families and 42 full-sib families of L. vannamei were produced using artificial fertilization from 2-4 dams by each sire, and measured at around five months post-metamorphosis. The results show that hentabilities among vanous traits were high: 0.515±0.030 for body weight and 0.394±0.030 for total length. After one generation of selection. the selection response was 10.70% for offspring growth. In the 5th month, the realized heritability for weight was 0.296 for the offspnng generation. Genetic correlations between body weight and body size were highly variable. The results indicate that external morphological parameters can be applied dunng breeder selection for enhancing the growth without sacrificing animals for determining the body size and breed ability; and selective breeding can be improved significantly, simultaneously with increased production.

Tunable Engineered Skin Mechanics via Coaxial Electrospun Fiber Core Diameter

PubMed Central

Blackstone, Britani Nicole; Drexler, Jason William

2014-01-01

Autologous engineered skin (ES) offers promise as a treatment for massive full thickness burns. Unfortunately, ES is orders of magnitude weaker than normal human skin causing it to be difficult to apply surgically and subject to damage by mechanical shear in the early phases of engraftment. In addition, no manufacturing strategy has been developed to tune ES biomechanics to approximate the native biomechanics at different anatomic locations. To enhance and tune ES biomechanics, a coaxial (CoA) electrospun scaffold platform was developed from polycaprolactone (PCL, core) and gelatin (shell). The ability of the coaxial fiber core diameter to control both scaffold and tissue mechanics was investigated along with the ability of the gelatin shell to facilitate cell adhesion and skin development compared to pure gelatin, pure PCL, and a gelatin-PCL blended fiber scaffold. CoA ES exhibited increased cellular adhesion and metabolism versus PCL alone or gelatin-PCL blend and promoted the development of well stratified skin with a dense dermal layer and a differentiated epidermal layer. Biomechanics of the scaffold and ES scaled linearly with core diameter suggesting that this scaffold platform could be utilized to tailor ES mechanics for their intended grafting site and reduce graft damage in vitro and in vivo. PMID:24712409

Polymeric Endoaortic Paving (PEAP): Mechanical, Thermoforming, and Degradation Properties of Polycaprolactone/Polyurethane Blends for Cardiovascular Applications

PubMed Central

Ashton, John H.; Mertz, James A. M.; Harper, John L.; Slepian, Marvin J.; Mills, Joseph L.; McGrath, Dominic V.; Vande Geest, Jonathan P.

2010-01-01

Polymeric endoaortic paving (PEAP) is a process by which a polymer is endovascularly delivered and thermoformed to coat or “pave” the lumen of the aorta. This method may offer an improvement to conventional endoaortic therapy in allowing conformal graft application with reduced risk of endoleak and customization to complex patient geometries. Polycaprolactone (PCL)/polyurethane (PU) blends of various blend ratios were assessed as a potential material for PEAP by characterizing their mechanical, thermoforming, and degradation properties. Biaxial tension testing revealed that the blends' stiffness is similar to that of aortic tissue, is higher for blends with more PCL content, and may be affected by thermoforming and degradation. Tubes of blends were able to maintain a higher diameter increase after thermoforming at higher PCL content and higher heating temperatures; 50/50 blend tubes heated to 55°C were able to maintain 90% of the diameter increase applied. Delamination forces of the blends ranged from 41 to 235 N/m2. In a Pseudomonas lipase solution, the 50/50 blend had a 94% lower degradation rate than pure PCL, and the 10/90 blend exhibited no degradation. These results indicate that PEAP, consisting of a PCL/PU blend, may be useful in developing the next generation of endoaortic therapy. PMID:20832506

Mismatch of Posttraumatic Stress Disorder (PTSD) Symptoms and DSM-IV Symptom Clusters in a Cancer Sample: Exploratory Factor Analysis of the PTSD Checklist-Civilian Version

PubMed Central

Shelby, Rebecca A.; Golden-Kreutz, Deanna M.; Andersen, Barbara L.

2007-01-01

The Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition (DSM-IV; American Psychiatric Association, 1994a) conceptualization of posttraumatic stress disorder (PTSD) includes three symptom clusters: reexperiencing, avoidance/numbing, and arousal. The PTSD Checklist-Civilian Version (PCL-C) corresponds to the DSM-IV PTSD symptoms. In the current study, we conducted exploratory factor analysis (EFA) of the PCL-C with two aims: (a) to examine whether the PCL-C evidenced the three-factor solution implied by the DSM-IV symptom clusters, and (b) to identify a factor solution for the PCL-C in a cancer sample. Women (N = 148) with Stage II or III breast cancer completed the PCL-C after completion of cancer treatment. We extracted two-, three-, four-, and five-factor solutions using EFA. Our data did not support the DSM-IV PTSD symptom clusters. Instead, EFA identified a four-factor solution including reexperiencing, avoidance, numbing, and arousal factors. Four symptom items, which may be confounded with illness and cancer treatment-related symptoms, exhibited poor factor loadings. Using these symptom items in cancer samples may lead to overdiagnosis of PTSD and inflated rates of PTSD symptoms. PMID:16281232

Improvement of the compressive strength of a cuttlefish bone-derived porous hydroxyapatite scaffold via polycaprolactone coating.

PubMed

Kim, Beom-Su; Kang, Hyo Jin; Lee, Jun

2013-10-01

Cuttlefish bones (CBs) have emerged as attractive biomaterials because of their porous structure and components that can be converted into hydroxyapatite (HAp) via a hydrothermal reaction. However, their brittleness and low strength restrict their application in bone tissue engineering. Therefore, to improve the compressive strength of the scaffold following hydrothermal conversion to a HAp form of CB (CB-HAp), the scaffold was coated using a polycaprolactone (PCL) polymer at various concentrations. In this study, raw CB was successfully converted into HAp via a hydrothermal reaction. We then evaluated their surface properties and composition by scanning electron microscopy and X-ray diffraction analysis. The CB-HAp coated with PCL showed improved compressive performance and retained a microporous structure. The compressive strength was significantly increased upon coating with 5 and 10% PCL, by 2.09- and 3.30-fold, respectively, as compared with uncoated CB-HAp. However, coating with 10% PCL resulted in a reduction in porosity. Furthermore, an in vitro biological evaluation demonstrated that MG-63 cells adhered well, proliferated and were able to be differentiated on the PCL-coated CB-HAp scaffold, which was noncytotoxic. These results suggest that a simple coating method is useful to improve the compressive strength of CB-HAp for bone tissue engineering applications. Copyright © 2013 Wiley Periodicals, Inc.

SLM produced porous titanium implant improvements for enhanced vascularization and osteoblast seeding.

PubMed

Matena, Julia; Petersen, Svea; Gieseke, Matthias; Kampmann, Andreas; Teske, Michael; Beyerbach, Martin; Murua Escobar, Hugo; Haferkamp, Heinz; Gellrich, Nils-Claudius; Nolte, Ingo

2015-04-02

To improve well-known titanium implants, pores can be used for increasing bone formation and close bone-implant interface. Selective Laser Melting (SLM) enables the production of any geometry and was used for implant production with 250-µm pore size. The used pore size supports vessel ingrowth, as bone formation is strongly dependent on fast vascularization. Additionally, proangiogenic factors promote implant vascularization. To functionalize the titanium with proangiogenic factors, polycaprolactone (PCL) coating can be used. The following proangiogenic factors were examined: vascular endothelial growth factor (VEGF), high mobility group box 1 (HMGB1) and chemokine (C-X-C motif) ligand 12 (CXCL12). As different surfaces lead to different cell reactions, titanium and PCL coating were compared. The growing into the porous titanium structure of primary osteoblasts was examined by cross sections. Primary osteoblasts seeded on the different surfaces were compared using Live Cell Imaging (LCI). Cross sections showed cells had proliferated, but not migrated after seven days. Although the cell count was lower on titanium PCL implants in LCI, the cell count and cell spreading area development showed promising results for titanium PCL implants. HMGB1 showed the highest migration capacity for stimulating the endothelial cell line. Future perspective would be the incorporation of HMGB1 into PCL polymer for the realization of a slow factor release.

ECM Inspired Coating of Embroidered 3D Scaffolds Enhances Calvaria Bone Regeneration

PubMed Central

Rentsch, C.; Rentsch, B.; Heinemann, S.; Bernhardt, R.; Bischoff, B.; Förster, Y.; Scharnweber, D.; Rammelt, S.

2014-01-01

Resorbable polymeric implants and surface coatings are an emerging technology to treat bone defects and increase bone formation. This approach is of special interest in anatomical regions like the calvaria since adults lose the capacity to heal large calvarial defects. The present study assesses the potential of extracellular matrix inspired, embroidered polycaprolactone-co-lactide (PCL) scaffolds for the treatment of 13 mm full thickness calvarial bone defects in rabbits. Moreover the influence of a collagen/chondroitin sulfate (coll I/cs) coating of PCL scaffolds was evaluated. Defect areas filled with autologous bone and empty defects served as reference. The healing process was monitored over 6 months by combining a novel ultrasonographic method, radiographic imaging, biomechanical testing, and histology. The PCL coll I/cs treated group reached 68% new bone volume compared to the autologous group (100%) and the biomechanical stability of the defect area was similar to that of the gold standard. Histological investigations revealed a significantly more homogenous bone distribution over the whole defect area in the PCL coll I/cs group compared to the noncoated group. The bioactive, coll I/cs coated, highly porous, 3-dimensional PCL scaffold acted as a guide rail for new skull bone formation along and into the implant. PMID:25013767

Facile fabrication of aloe vera containing PCL nanofibers for barrier membrane application.

PubMed

Carter, Princeton; Rahman, Shekh M; Bhattarai, Narayan

2016-01-01

Guided tissue regeneration (GTR) is a widely used method in dental surgical procedures that utilizes a barrier membrane to exclude migration of epithelium and ensure repopulation of periodontal ligament cells at the sites having insufficient gingiva. Commercial GTR membranes are typically composed of synthetic polymers that have had mild clinical success mostly because of their lack of proper bioactivity and appropriate degradation profile. In this study, a natural polymer, aloe vera was blended with polycaprolactone (PCL) to create nanofibrous GTR membranes by electrospinning. Aloe vera has proven anti-inflammatory properties and enhances the regeneration of periodontium tissues. PCL, a synthetic polymer, is well known to produce miscible polyblends nanofibers with natural polymers. Nanofibrous membranes with varying composition of PCL to aloe vera were fabricated, and several physicochemical and biological properties, such as fiber morphology, wettability, chemical structure, mechanical strength, and cellular compatibility of the membranes were analyzed. PCL/aloe vera membranes with ratios from 100/00 to 70/30 showed good uniformity in fiber morphology and suitable mechanical properties, and retained the integrity of their fibrous structure in aqueous solutions. Experimental results, using cell viability assay and cell attachment observation, showed that the nanofibrous membranes support 3T3 cell viability and could be a potential candidate for GTR therapy.

Polymeric nanoparticles affect the intracellular delivery, antiretroviral activity and cytotoxicity of the microbicide drug candidate dapivirine.

PubMed

das Neves, José; Michiels, Johan; Ariën, Kevin K; Vanham, Guido; Amiji, Mansoor; Bahia, Maria Fernanda; Sarmento, Bruno

2012-06-01

To assess the intracellular delivery, antiretroviral activity and cytotoxicity of poly(ε-caprolactone) (PCL) nanoparticles containing the antiretroviral drug dapivirine. Dapivirine-loaded nanoparticles with different surface properties were produced using three surface modifiers: poloxamer 338 NF (PEO), sodium lauryl sulfate (SLS) and cetyl trimethylammonium bromide (CTAB). The ability of nanoparticles to promote intracellular drug delivery was assessed in different cell types relevant for vaginal HIV transmission/microbicide development. Also, antiretroviral activity of nanoparticles was determined in different cell models, as well as their cytotoxicity. Dapivirine-loaded nanoparticles were readily taken up by different cells, with particular kinetics depending on the cell type and nanoparticles, resulting in enhanced intracellular drug delivery in phagocytic cells. Different nanoparticles showed similar or improved antiviral activity compared to free drug. There was a correlation between increased antiviral activity and increased intracellular drug delivery, particularly when cell models were submitted to a single initial short-course treatment. PEO-PCL and SLS-PCL nanoparticles consistently showed higher selectivity index values than free drug, contrasting with high cytotoxicity of CTAB-PCL. These results provide evidence on the potential of PCL nanoparticles to affect in vitro toxicity and activity of dapivirine, depending on surface engineering. Thus, this formulation approach may be a promising strategy for the development of next generation microbicides.

Synthesis and characterization of segmented poly(esterurethane urea) elastomers for bone tissue engineering

PubMed Central

Kavlock, Katherine D.; Pechar, Todd W.; Hollinger, Jeffrey O.; Guelcher, Scott A.; Goldstein, Aaron S.

2007-01-01

Segmented polyurethanes have been used extensively in implantable medical devices, but their tunable mechanical properties make them attractive for examining the effect of biomaterial modulus on engineered musculoskeletal tissue development. In this study a family of segmented degradable poly(esterurethane urea)s (PEUURs) were synthesized from 1,4-diisocyanatobutane, a poly(ε-caprolactone) (PCL) macrodiol soft segment and a tyramine-1,4-diisocyanatobutane-tyramine chain extender. By systematically increasing the PCL macrodiol molecular weight from 1100 to 2700 Da, the storage modulus, crystallinity and melting point of the PCL segment were systematically varied. In particular, the melting temperature, Tm, increased from 21 to 61°C and the storage modulus at 37°C increased from 52 to 278 MPa with increasing PCL macrodiol molecular weight, suggesting that the crystallinity of the PCL macrodiol contributed significantly to the mechanical properties of the polymers. Bone marrow stromal cells were cultured on rigid polymer films under osteogenic conditions for up to 14 days. Cell density, alkaline phosphatase activity, and osteopontin and osteocalcin expression were similar among PEUURs and comparable to poly(D,L-lactic-coglycolic acid). This study demonstrates the suitability of this family of PEUURs for tissue engineering applications, and establishes a foundation for determining the effect of biomaterial modulus on bone tissue development. PMID:17418651

PCL-PGLA composite tubular scaffold preparation and biocompatibility investigation.

PubMed

Mo, X; Weber, H-J; Ramakrishna, S

2006-08-01

The objective of this paper was to fabricate a biodegradable tubular scaffold for small diameter (d<6 mm) blood vessel tissue engineering. The tube scaffold needed a porous wall for cell attachment, proliferation and tissue regeneration with its degradation. A novel method given in this paper was to coat a porous layer of poly (epsilon-caprolactone) (PCL) on the outside of a poly (glycolic-co-lactic acid) (PGLA with GA:LA=90:10) fiber braided tube to give a PCL-PGLA composite. The PGLA tube was fabricated using a braiding machine by inserting a Teflon tube with the desired diameter in center of the 20 spindles, which are the carriers of PGLA fibers. Changing the diameter of the Teflon tube can vary the inner diameter of a braided PGLA tube. Thermally induced phase separation method was used for PCL solution coating on the surface of the PGLA braided tube. Controlling the polymer concentration, non-solvent addition and quenching temperature generated the pore structures, with pore sizes ranging from 10-30 microm. The fibroblast cells were seeded on the tubular scaffold and cultured in vitro for the biocompatibility investigation. Histology results showed that the fibroblast cells proliferated on the interconnected pore of the PCL porous layer in 1 week.

Preparation of wormlike polymeric nanoparticles coated with silica for delivery of methotrexate and evaluation of anticancer activity against MCF7 cells.

PubMed

Gharebaghi, Farhad; Dalali, Naser; Ahmadi, Ebrahim; Danafar, Hossein

2017-04-01

Methotrexate is one of the most effective drugs that is commonly used in the treatment of cancer. However, its application is limited due to low solubility, high toxicity and rapid metabolism. Therefore, in the present study, worm-like polymeric nanoparticles as carrier of methotrexate were prepared using biodegradable copolymers (mPEG-PCL). The impact of nanoparticles' geometry on the loading, delivery and drug's anti-cancer activity was investigated. The di-block copolymer mPEG-PCL was being synthesized by a ring opening polymerization of ɛ-caprolactone in the presence of mPEG as the initiator and Sn(oct) 2 as the catalyst. It was used for the preparation of worm-like micelles and coated with silica, so that their structures are stable after drying. The synthesized copolymers and nanoparticles were characterized by FTIR, HNMR, GPC, XRD, TGA, DLS, and FE-SEM analyses. The efficiencies of drug loading and release of nanoparticles as in vitro, was studied by high performance liquid chromatography. The MTT method was used to estimate the toxicity on MCF-7 cell category. The obtained results showed that the nanoparticles were worm-like particles with less than 150 nm diameter and about 1 µm length. The loading and encapsulation efficiencies of drug by the worm-like nanoparticles were 3.5 ± 0.14% and 65.6 ± 0.12%, respectively, while they were obtained as 2.1 ± 0.08% and 26 ± 0.10%, respectively, for spherical nanoparticles. The methotrexate diffusional behavior of worm-like nanoparticles was compared with that of the spherical ones. On the other hand, the anti-cancer activity of MTX-loaded nanoparticles was more than the free drug. The results of the MTT assay showed strong and dose-dependent inhibition of cell (MCF-7 category) growth by the nanoparticles compared with MTX. The inhibitory concentrations (IC 50 i.e. reduction viability of cell to 50%) obtained for worm-like, spherical nanoparticles and free drug (incubation times 72 h) were 8.25 ± 0.20, 9.15 ± 0.17, 12.28 ± 0.15 µg/mL, respectively. It can be concluded that application of non-spherical nanoparticles is a better and more effective strategy for controlled and slow release of methotrexate in the treatment of cancer.

TPS/PCL composite reinforced with treated sisal fibers: property, biodegradation and water-absorption

USDA-ARS?s Scientific Manuscript database

Sisal fibers bleached with sodium-hydroxide followed by hydrogen peroxide treatment were incorporated in a thermoplastic starch;-polycaprolactone (TPS/PCL) blend via extrusion processing and examined for their property, biodegradability and water-absorption. Scanning electron microscopy revealed wel...

Evaluation of the Effect of Low Dietary Fermentable Carbohydrate Content on Growth Performance, Nutrient Digestibility, Blood Characteristics, and Meat Quality in Finishing Pigs

PubMed Central

Hong, S. M.; Hwang, J. H.; Kim, I. H.

2012-01-01

A total of 96 pigs (49.23±3.20 kg) were used in an 11 wk growth trial to evaluate the effect of fermentable carbohydrate (FC) content on growth performance, apparent total tract digestibility (ATTD) of nutrient, blood profile, and meat quality. The dietary treatments were: i) negative control (NC), basal diet, ii) positive control (PC), NC+antibiotics (positive control diet with 5 ppm flavomycin), iii) PCL, PC-13% lower FC, and iv) NCL, NC-13% lower FC. The growth performance (average daily gain, average daily feed intake, and gain/feed) didn’t differ among treatments through the whole experiment. These pigs fed the PCL diet had the greater (p<0.05) apparent total tract digestibility (ATTD) of dry matter than those from PC and NC treatment at the end of the experiment. No differences were observed in white blood cell (WBC), red blood cell (RBC), and lymphocyte concentration among different treatments. After the feeding period, meat samples were collected from the pigs at slaughter. The pigs in NCL and PCL treatments had greater (p<0.05) backfat thickness and lower lean percentage. The color value of loin was higher (p<0.05) in NCL treatment compared to PCL treatment. Also, the NCL treatment had higher (p<0.05) marbling value than PC treatment. The drip loss was depressed by PCL and NCL treatment comapared to NC treatments. The water holding capacity (WHC) was higher (p<0.05) in NC and PCL treatment. In conclusion, the low FC can improve digestibility and meat quality of finishing pigs. PMID:25049693

Co-delivery of hydrophilic and hydrophobic drugs by micelles: a new approach using drug conjugated PEG-PCLNanoparticles.

PubMed

Danafar, Hossein; Rostamizadeh, Kobra; Davaran, Soodabeh; Hamidi, Mehrdad

2017-11-01

Co-delivery strategy has been proposed to minimize the amount of each drug and to achieve the synergistic effect for cancer therapies. A conjugate of the antitumor drug, doxorubicin, with diblock methoxy poly (ethylene glycol)-poly caprolactone (mPEG-PCL) copolymer was synthesized by the reaction of mPEG-PCL copolymer with doxorubicin in the presence of p-nitrophenylchloroformate. The conjugated copolymer was characterized in vitro by 1 H-NMR, FTIR, DSC and GPC techniques. Then, the doxorubicin conjugated mPEG-PCL(DOX-mPEG-PCL) was self-assembled into micelles in the presence of curcumin in aqueous solution. The resulting micelles were characterized further by various techniques such as dynamic light scattering (DLS) and atomic force microscopy (AFM).The encapsulation efficiency of doxorubicin and curcumin were 82.31 ± 3.32 and 78.15 ± 3.14%, respectively. The results revealed that the micelles formed by the DOX-mPEG-PCL with and without curcumin have spherical structure with average size of 116 and 134 nm respectively. The release behavior of curcumin and doxorubicin loaded to micelles were investigated in a different media. The release rate of micelles consisted of the conjugated copolymer was pH dependent as it was higher at lower pH than in neutral condition. Another feature of the conjugated micelles was a sustained release profile. The cytotoxicity of micelles were evaluated by MTT (3-(4, 5-dimethylthiazol-2-yl)-2, 5-diphenyltetrazolium bromide, atetrazole) assay on lung cancer A549 cell lines. In vitro cytotoxicity assay showed that the mPEG-PCL copolymer did not affect the growth of A549 cells. The cytotoxic activity of the micelles against A549 cells was greater than free doxorubicin and free curcumin.

Dual-component system dimethyl sulfoxide/LiCl as a solvent and catalyst for homogeneous ring-opening grafted polymerization of ε-caprolactone onto xylan.

PubMed

Zhang, Xue-Qin; Chen, Ming-Jie; Liu, Chuan-Fu; Sun, Run-Cang

2014-01-22

The preparation of xylan-graft-poly(ε-caprolactone) (xylan-g-PCL) copolymers was investigated by homogeneous ring-opening polymerization (ROP) in a dual-component system containing Lewis base LiCl and strong polar aprotic solvent dimethyl sulfoxide (DMSO). DMSO/LiCl acted as solvent, base, and catalyst for the ROP reaction. The effects of the parameters, including the reaction temperature, molar ratio of ε-caprolactone (ε-CL) to anhydroxylose units (AXU) in xylan, and reaction time, on the degree of substitution (DS) and weight percent of PCL side chain (WPCL) were investigated. The results showed that xylan-g-PCL copolymers with low DS in the range of 0.03-0.39 were obtained under the given conditions. The Fourier transform infrared spectroscopy (FTIR), (1)H nuclear magnetic resonance (NMR), (13)C NMR, (1)H-(1)H correlation spectroscopy (COSY), and (1)H-(13)C correlation two-dimensional (2D) NMR [heteronuclear single-quantum coherence (HSQC)] characterization provided more evidence of the attachment of side chains onto xylan. Only one ε-CL was confirmed to be attached onto xylan with each side chain. Integration of resonances assigned to the substituted C2 and C3 in the HSQC spectrum also indicated 69.23 and 30.77% of PCL side chains attached to AXU at C3 and C2 positions, respectively. Although the attachment of PCL onto xylan led to the decreased thermal stability of xylan, the loss of unrecovered xylan fractions with low molecular weight because of the high solubility of xylan in DMSO/LiCl resulted in the increased thermal stability of the samples. This kind of xylan derivative has potential application in environmentally friendly and biodegradable materials considering the good biodegradability of xylan and PCL.

Carbon nanotubes in blends of polycaprolactone/thermoplastic starch.

PubMed

Taghizadeh, Ata; Favis, Basil D

2013-10-15

Despite the importance of polymer-polymer multiphase systems, very little work has been carried out on the preferred localization of solid inclusions in such multiphase systems. In this work, carbon nanotubes (CNT) are dispersed with polycaprolactone (PCL) and thermoplastic starch (TPS) at several CNT contents via a combined solution/twin-screw extrusion melt mixing method. A PCL/CNT masterbatch was first prepared and then blended with 20 wt% TPS. Transmission and scanning electron microscopy images reveal a CNT localization principally in the TPS phase and partly at the PCL/TPS interface, with no further change by annealing. This indicates a strong driving force for the CNTs toward TPS. Young's model predicts that the nanotubes should be located at the interface. X-ray photoelectron spectroscopy (XPS) of extracted CNTs quantitatively confirms an encapsulation by TPS and reveals a covalent bonding of CNTs with thermoplastic starch. It appears likely that the nanotubes migrate to the interface, react with TPS and then are subsequently drawn into the low viscosity TPS phase. In a low shear rate/low shear stress internal mixer the nanotubes are found both in the PCL phase and at the PCL/TPS interface and have not completed the transit to the TPS phase. This latter result indicates the importance of choosing appropriate processing conditions in order to minimize kinetic effects. The addition of CNTs to PCL results in an increase in the crystallization temperature and a decrease in the percent crystallinity confirming the heterogeneous nucleating effect of the nanotubes. Finally, DMA analysis reveals a dramatic decrease in the starch rich phase transition temperature (~26 °C), for the system with nanotubes located in the TPS phase. Copyright © 2013 Elsevier Ltd. All rights reserved.

In-vivo characterization of a 3D hybrid scaffold based on PCL/decellularized aorta for tracheal tissue engineering.

PubMed

Ghorbani, Fariba; Moradi, Lida; Shadmehr, Mohammad Behgam; Bonakdar, Shahin; Droodinia, Atosa; Safshekan, Farzaneh

2017-12-01

As common treatments for long tracheal stenosis are associated with several limitations, tracheal tissue engineering is considered as an alternative treatment. This study aimed at preparing a hybrid scaffold, based on biologic and synthetic materials for tracheal tissue engineering. Three electrospun polycaprolactone (PCL) scaffolds, namely E1 (pure PCL), E2 (collagen-coated PCL) and E3 (PCL blended with collagen) were prepared. Allogeneic aorta was harvested and decellularized. A biodegradable PCL stent was fabricated and inserted into the aorta to prevent its collapse. Scaffold characterization results revealed that the 2-h swelling ratio of E2 was significantly higher than those of E1 and E3. In the first 3months, E2 and E3 exhibited almost equal degradabilities (significantly higher than that of E1). Moreover, tensile strengths of all samples were comparable with those of human trachea. Using rabbit's adipose-derived mesenchymal stem cells (AMSCs) and primary chondrocytes, E3 exhibited the highest levels of GAG release within 21days as well as collagen II and aggrecan expression. Fot the next step, AMSC-chondrocyte co-culture seeded scaffold was sutured to the acellular aorta, implanted into rabbits' muscle, and finally harvested after 4weeks of follow up. Harvested structures were totally viable due to the angiogenesis created by the muscle. H&E and alcian blue staining results revealed the presence of chondrocytes in the structure and GAG in the produced extracellular matrix. Since tracheal replacement using biologic and synthetic scaffolds usually results in tracheal collapse or granulation formation, a hybrid construct may provide the required rigidity and biocompatibility for the substitute. Copyright © 2017. Published by Elsevier B.V.

Nanosized CaP-silk fibroin-PCL-PEG-PCL/PCL based bilayer membranes for guided bone regeneration.

PubMed

Türkkan, Sibel; Pazarçeviren, A Engin; Keskin, Dilek; Machin, Nesrin E; Duygulu, Özgür; Tezcaner, Ayşen

2017-11-01

Guided bone regeneration (GBR) concept has been developed to prevent the formation of non-functional scar tissue layer on defect site by undertaking barrier role. In this study, a new bilayer membrane which consisted of one layer of electrospun silk fibroin/PCL-PEG-PCL incorporating nanocalcium phosphate (SPCA) 1 and one layer of PCL membrane was developed for GBR. To improve the osteoconductivity of membranes, nanosized calcium phosphate particles synthesized by Flame Spray Pyrolysis method were incorporated into membranes at 10% (wt) (SPCA10) and 20% (wt) (SPCA20) of the polymer content. The structural and chemical analyses revealed the well-integrated two layers of membranes with a total thickness of ca 100μm. In the regenerative layer, the highly porous mesh structure had a thickness of 12.6μm with randomly oriented fibers having diameters around 760nm, and nanoparticles dispersed homogenously. The mechanical test results showed remarkable improvement on the tensile strength of membranes with incorporation of nanoparticles. Higher water affinity of nanoCaP included membranes was proved by lower contact angle values and higher percent water uptake capacity. Biomineralization assay revealed that nucleation and growth of apatites around fibers of SPCA10 and SPCA20 were apparent while on SPCA0 apatite minerals were barely detected after 10days. Human dental pulp stem cells (DPSC) were seeded on electrospun layer of the bilayer membranes for biocompatibility and osteo-compatibility study. Increasing nanoCaP amount resulted in higher cell adhesion, proliferation, ALP activity and calcium deposition on membranes. These overall results confirmed the biocompatibility and potential applicability of proposed membranes for GBR treatments. Copyright © 2017 Elsevier B.V. All rights reserved.

From traditional to patient-centered learning: curriculum change as an intervention for changing institutional culture and promoting professionalism in undergraduate medical education.

PubMed

Christianson, Charles E; McBride, Rosanne B; Vari, Richard C; Olson, Linda; Wilson, H David

2007-11-01

The authors reframe a curriculum change from a traditional lecture-based to an integrated patient-centered approach as an intervention for changing the culture and hidden curriculum of an institution in ways that promote professionalism. Within this context, the authors articulate some of the inherent process and relational factors brought about by these curricular changes that are essential elements of this intervention process. In 1998 the University of North Dakota School of Medicine and Health Sciences (UNDSMHS) introduced a new preclinical patient-centered learning (PCL) curriculum for first- and second-year medical students. Case-based, small-group learning forms the critical foundation of the PCL process, and an integrated basic and clinical science didactic component supports this process. At the student level, the case-based PCL process generates innovative opportunities for professionalism education from the explicitly articulated formal content that arises naturally from the cases, but more importantly from the implicit values inherent to the PCL small-group process itself--humanism, accountability, pursuit of excellence, and altruism. Further, the organizational changes necessary for the transformation to the PCL curriculum required process changes at student, faculty, and administrative levels that have resulted in a cultural shift toward relationship centeredness within the institution. The authors describe the evolution and structure of the PCL curriculum at UNDSMHS and how this curricular transformation has served as an intervention that promotes professionalism and institutional culture change through (1) processes at the student level that present new opportunities for professionalism education, and (2) processes at student, faculty, administrative, and institutional levels that have created an institutional culture that supports, models, and promotes relationship-centered professional values.

Preparation and characterization of monomethoxy poly(ethylene glycol)-poly(ε-caprolactone) micelles for the solubilization and in vivo delivery of luteolin

PubMed Central

Qiu, Jin-Feng; Gao, Xiang; Wang, Bi-Lan; Wei, Xia-Wei; Gou, Ma-Ling; Men, Ke; Liu, Xing-Yu; Guo, Gang; Qian, Zhi-Yong; Huang, Mei-Juan

2013-01-01

Luteolin (Lu) is one of the flavonoids with anticancer activity, but its poor water solubility limits its use clinically. In this work, we used monomethoxy poly(ethylene glycol)-poly(e-caprolactone) (MPEG-PCL) micelles to encapsulate Lu by a self-assembly method, creating a water-soluble Lu/MPEG-PCL micelle. These micelles had a mean particle size of 38.6 ± 0.6 nm (polydispersity index = 0.16 ± 0.02), encapsulation efficiency of 98.32% ± 1.12%, and drug loading of 3.93% ± 0.25%. Lu/MPEG-PCL micelles could slowly release Lu in vitro. Encapsulation of Lu in MPEG-PCL micelles improved the half-life (t½; 152.25 ± 49.92 versus [vs] 7.16 ± 1.23 minutes, P = 0.007), area under the curve (0-t) (2914.05 ± 445.17 vs 502.65 ± 140.12 mg/L/minute, P = 0.001), area under the curve (0–∞) (2989.03 ± 433.22 vs 503.81 ± 141.41 mg/L/minute, P = 0.001), and peak concentration (92.70 ± 11.61 vs 38.98 ± 7.73 mg/L, P = 0.003) of Lu when the drug was intravenously administered at a dose of 30 mg/kg in rats. Also, Lu/MPEG-PCL micelles maintained the cytotoxicity of Lu on 4T1 breast cancer cells (IC50 = 6.4 ± 2.30 μg/mL) and C-26 colon carcinoma cells (IC50 = 12.62 ± 2.17 μg/mL) in vitro. These data suggested that encapsulation of Lu into MPEG-PCL micelles created an aqueous formulation of Lu with potential anticancer effect. PMID:23990719

Photocatalytic antibacterial effect of ZnO nanoparticles into coaxial electrospun PCL fibers to prevent infections from skin injuries

NASA Astrophysics Data System (ADS)

Prado-Prone, G.; Silva-Bermúdez, P.; García-Macedo, J. A.; Almaguer-Flores, A.; Ibarra, C.; Velasquillo-Martínez, C.

2017-02-01

Antibacterial studies of inorganic nanoparticles (nps) have become important due to the increased bacterial resistance against antibiotics. We used Zinc oxide nanoparticles (ZnO nps), which possess excellent photocatalytic properties with a wide band gap (Eg), are listed as "generally recognized as safe" by the Food and Drug Administration (FDA) and have shown antibacterial activity (AA) against many bacterial strains. The AA of ZnO nps is partly attributed to the production of Reactive Oxygen Species (ROS) by photocatalysis. When ZnO nps in aqueous media are illuminated with an energy

Solid freeform fabrication and in-vitro response of osteoblast cells of mPEG-PCL-mPEG bone scaffolds.

PubMed

Jiang, Cho-Pei; Chen, Yo-Yu; Hsieh, Ming-Fa; Lee, Hung-Maan

2013-04-01

Bone tissue engineering is an emerging approach to provide viable substitutes for bone regeneration. Poly(ethylene glycol) (PEG) is a good candidate of bone scaffold because of several advantages such as hydrophilicity, biocompatibility, and intrinsic resistance to protein adsorption and cell adhesion. However, its low compressive strength limits application for bone regeneration. Poly(ε-caprolactone) (PCL), a hydrophobic nonionic polymer, is adopted to enhance the compressive strength of PEG alone.We aimed to investigate the in-vitro response of osteoblast-like cells cultured with porous scaffolds of triblock PEG-PCL-PEG copolymer fabricated by an air pressure-aided deposition system. A desktop air pressure-aided deposition system that involves melting and plotting PEG-PCL-PEG was used to fabricate three-dimensional scaffolds having rectangular pores. The experimental results showed that PEG-PCL-PEG with a molecular weight of 25,000 can be melted and stably deposited through a heating nozzle at an air pressure of 0.3 MPa and no crack occurs after it solidifies. The scaffolds with pre-determined pore size of 400× 420 μm and a porosity of 79 % were fabricated, and their average compressive strength was found to be 18.2 MPa. Osteoblast-like cells, MC3T3-E1, were seeded on fabricated scaffolds to investigate the in-vitro response of cells including toxicity and cellular locomotion. In a culture period of 28 days, the neutral-red stained osteoblasts were found to well distributed in the interior of the scaffold. Furthermore, the cellular attachment and movement in the first 10 h of cell culture were observed with time-lapse microscopy indicating that the porous PEG-PCL-PEG scaffolds fabricated by air pressure-aided deposition system is non-toxicity for osteoblast-like cells.

3D artificial bones for bone repair prepared by computed tomography-guided fused deposition modeling for bone repair.

PubMed

Xu, Ning; Ye, Xiaojian; Wei, Daixu; Zhong, Jian; Chen, Yuyun; Xu, Guohua; He, Dannong

2014-09-10

The medical community has expressed significant interest in the development of new types of artificial bones that mimic natural bones. In this study, computed tomography (CT)-guided fused deposition modeling (FDM) was employed to fabricate polycaprolactone (PCL)/hydroxyapatite (HA) and PCL 3D artificial bones to mimic natural goat femurs. The in vitro mechanical properties, in vitro cell biocompatibility, and in vivo performance of the artificial bones in a long load-bearing goat femur bone segmental defect model were studied. All of the results indicate that CT-guided FDM is a simple, convenient, relatively low-cost method that is suitable for fabricating natural bonelike artificial bones. Moreover, PCL/HA 3D artificial bones prepared by CT-guided FDM have more close mechanics to natural bone, good in vitro cell biocompatibility, biodegradation ability, and appropriate in vivo new bone formation ability. Therefore, PCL/HA 3D artificial bones could be potentially be of use in the treatment of patients with clinical bone defects.

Structural analysis of β-prism lectin from Colocasia esculenta (L.) S chott.

PubMed

Vajravijayan, S; Pletnev, S; Pletnev, V Z; Nandhagopal, N; Gunasekaran, K

2016-10-01

The Mannose-binding β-Prism Colocasia esculenta lectin (β-PCL) was purified from tubers using ion exchange chromatography. The purified β-PCL appeared as a single band of ∼12kDa on SDS-PAGE. β-PCL crystallizes in trigonal space group P3121 and diffracted to a resolution of 2.1Å. The structure was solved using Molecular replacement using Crocus vernus lectin (PDB: 3MEZ) as a model. From the final refined model to an R-factor of 16.5% and an Rfree of 20.4%, it has been observed that the biological unit consists of two β-Prism domains augmented through C-terminals swap over to form one of faces for each domain. Cα superposition of individual domains of β-PCL with individual domains of other related structures and superposition of whole protein structures were carried out. The higher RMS deviation for the superposition of whole structures suggest that β-prism domains assume different orientation in each structure. Copyright © 2016 Elsevier B.V. All rights reserved.

Novel Injectable Pentablock Copolymer Based Thermoresponsive Hydrogels for Sustained Release Vaccines.

PubMed

Bobbala, Sharan; Tamboli, Viral; McDowell, Arlene; Mitra, Ashim K; Hook, Sarah

2016-01-01

The need for multiple vaccinations to enhance the immunogenicity of subunit vaccines may be reduced by delivering the vaccine over an extended period of time. Here, we report two novel injectable pentablock copolymer based thermoresponsive hydrogels made of polyethyleneglycol-polycaprolactone-polylactide-polycaprolactone-polyethyleneglycol (PEG-PCL-PLA-PCL-PEG) with varying ratios of polycaprolactone (PCL) and polylactide (PLA), as single shot sustained release vaccines. Pentablock copolymer hydrogels were loaded with vaccine-encapsulated poly lactic-co-glycolic acid nanoparticles (PLGA-NP) or with the soluble vaccine components. Incorporation of PLGA-NP into the thermoresponsive hydrogels increased the complex viscosity of the gels, lowered the gelation temperature, and minimized the burst release of antigen and adjuvants. The two pentablock hydrogels stimulated both cellular and humoral responses. The addition of PLGA-NP to the hydrogels sustained immune responses for up to 49 days. The polymer with a higher ratio of PCL to PLA formed a more rigid gel, induced stronger immune responses, and stimulated effective anti-tumor responses in a prophylactic melanoma tumor model.

Cytocompatibility of electrospun nanofiber tubular scaffolds for small diameter tissue engineering blood vessels.

PubMed

Xiang, Ping; Li, Min; Zhang, Chao-ying; Chen, Deng-long; Zhou, Zhi-hua

2011-10-01

A tubular scaffold was fabricated by using electrospun polymer solution blends of pNSR32 (recombinant spider silk protein), PCL (polycaprolactone) and Gt (gelatin). The physicochemical properties and cytocompatibility of these scaffolds were investigated. Afterwards, the pNSR32/PCL/Gt tubular scaffold (inner diameter=3mm) showed high porosity of 86.2 ± 2.9%, pore size of 2423 ± 979nm and average fibre diameter of 166 ± 85nm. Water uptake and contact angle of the scaffolds reached 112.0 ± 4.4% and 45.7 ± 13.7°, respectively. SDRAECs (Sprague Dawley Rat Aortic Endothelial Cells) grew and proliferated well and phenotype could be maintained on the composite scaffolds after they had been cultured on the composite scaffolds for 7 days. Compared with pure PCL scaffolds a greater density of viable cells was seen on the composites, especially the pNSR32/PCL/Gt scaffolds. Copyright © 2011 Elsevier B.V. All rights reserved.

Effects of 3D-Printed Polycaprolactone/β-Tricalcium Phosphate Membranes on Guided Bone Regeneration

PubMed Central

Shim, Jin-Hyung; Won, Joo-Yun; Park, Jung-Hyung; Bae, Ji-Hyeon; Ahn, Geunseon; Kim, Chang-Hwan; Lim, Dong-Hyuk; Cho, Dong-Woo; Yun, Won-Soo; Bae, Eun-Bin; Jeong, Chang-Mo; Huh, Jung-Bo

2017-01-01

This study was conducted to compare 3D-printed polycaprolactone (PCL) and polycaprolactone/β-tricalcium phosphate (PCL/β-TCP) membranes with a conventional commercial collagen membrane in terms of their abilities to facilitate guided bone regeneration (GBR). Fabricated membranes were tested for dry and wet mechanical properties. Fibroblasts and preosteoblasts were seeded into the membranes and rates and patterns of proliferation were analyzed using a kit-8 assay and by scanning electron microscopy. Osteogenic differentiation was verified by alizarin red S and alkaline phosphatase (ALP) staining. An in vivo experiment was performed using an alveolar bone defect beagle model, in which defects in three dogs were covered with different membranes. CT and histological analyses at eight weeks after surgery revealed that 3D-printed PCL/β-TCP membranes were more effective than 3D-printed PCL, and substantially better than conventional collagen membranes in terms of biocompatibility and bone regeneration and, thus, at facilitating GBR. PMID:28441338

Effects of 3D-Printed Polycaprolactone/β-Tricalcium Phosphate Membranes on Guided Bone Regeneration.

PubMed

Shim, Jin-Hyung; Won, Joo-Yun; Park, Jung-Hyung; Bae, Ji-Hyeon; Ahn, Geunseon; Kim, Chang-Hwan; Lim, Dong-Hyuk; Cho, Dong-Woo; Yun, Won-Soo; Bae, Eun-Bin; Jeong, Chang-Mo; Huh, Jung-Bo

2017-04-25

This study was conducted to compare 3D-printed polycaprolactone (PCL) and polycaprolactone/β-tricalcium phosphate (PCL/β-TCP) membranes with a conventional commercial collagen membrane in terms of their abilities to facilitate guided bone regeneration (GBR). Fabricated membranes were tested for dry and wet mechanical properties. Fibroblasts and preosteoblasts were seeded into the membranes and rates and patterns of proliferation were analyzed using a kit-8 assay and by scanning electron microscopy. Osteogenic differentiation was verified by alizarin red S and alkaline phosphatase (ALP) staining. An in vivo experiment was performed using an alveolar bone defect beagle model, in which defects in three dogs were covered with different membranes. CT and histological analyses at eight weeks after surgery revealed that 3D-printed PCL/β-TCP membranes were more effective than 3D-printed PCL, and substantially better than conventional collagen membranes in terms of biocompatibility and bone regeneration and, thus, at facilitating GBR.

Assessing psychopathy in forensic schizophrenia spectrum disorders: Validating the Comprehensive Assessment of the Psychopathic Personality-Institutional Rating Scale (CAPP-IRS).

PubMed

De Page, Louis; Mercenier, Sophie; Titeca, Pierre

2018-07-01

The assessment of psychopathy in (forensic) schizophrenia spectrum disorders is long-standing debate. In the present study, we investigated the psychometric properties of the Comprehensive Assessment of Psychopathic Personality-Institutional Rating Scale (CAPP-IRS) in a sample of 72 male forensic patients with a primary diagnosis of schizophrenia spectrum disorders. We compared the CAPP-IRS' psychometric properties to those of the Psychopathy Checklist-Revised (PCL-R). The CAPP-IRS showed good interrater reliability and internal consistency except for the CAPP-IRS Cognition and Emotional Domains. There appears to be a larger but intelligible overlap between the CAPP-IRS and schizophrenia symptoms than between the PCL-R and schizophrenia symptoms. Inversely, the PCL-R showed overall stronger associations with risk assessment measures. We conclude that, in (forensic) schizophrenia disorder spectrum patients, the CAPP-IRS has closer associations with clinical features, while the PCL-R is better a predicting risk and life-time dimensions. Copyright © 2018. Published by Elsevier B.V.