Numerical simulation of adverse-pressure-gradient boundary layer with or without roughness

NASA Astrophysics Data System (ADS)

Mottaghian, Pouya; Yuan, Junlin; Piomelli, Ugo

2014-11-01

Large-eddy and direct numerical simulations are carried out on flat-plate boundary layer over smooth and rough surfaces, with adverse pressure gradient.The deceleration is achieved by imposing a wall-normal freestream velocity profile, and is strong enough to cause separation at the wall. The Reynolds number based on momentum thickness and freestream velocity at inlet is 600. Numerical sandgrain roughness is applied based on an immersed boundary method, yielding a flow that is transitionally rough. The turbulence intensity increases before separation, and reaches a higher value for the rough case, indicating stronger mixing. Roughness also causes higher momentum deficit near the wall, leading to earlier separation. This is consistent with previous observation made on rough-wall flow separation over a ramp. In both cases, the turbulent kinetic energy peaks inside the shear layer above the detachment region, with higher values in the rough case; it then decreases approaching the reattachment region. Near the wall inside the separation bubble, the near-zero turbulent intensity indicates that the turbulent structures are lifted up in the separation region. Compared with the smooth case, the shear layer is farther from the wall and the reattachment length is longer on the rough wall.

Effect of surface deposits on electromagnetic waves propagating in uniform ducts

NASA Technical Reports Server (NTRS)

Baumeister, Kenneth J.

1990-01-01

A finite-element Galerkin formulation was used to study the effect of material surface deposits on the reflective characteristics of straight uniform ducts with PEC (perfectly electric conducting) walls. Over a wide frequency range, the effect of both single and multiple surface deposits on the duct reflection coefficient were examined. The power reflection coefficient was found to be significantly increased by the addition of deposits on the wall.

Research on wall shear stress considering wall roughness when shear swirling flow vibration cementing

NASA Astrophysics Data System (ADS)

Cui, Zhihua; Ai, Chi; Feng, Fuping

2017-01-01

When shear swirling flow vibration cementing, the casing is revolving periodically and eccentrically, which leads to the annulus fluid in turbulent swirling flow state. The wall shear stress is more than that in laminar flow field when conventional cementing. The paper mainly studied the wall shear stress distribution on the borehole wall when shear swirling flow vibration cementing based on the finite volume method. At the same time, the wall roughness affected and changed the turbulent flow near the borehole wall and the wall shear stress. Based on the wall function method, the paper established boundary conditions considering the wall roughness and derived the formula of the wall shear stress. The results showed that the wall roughness significantly increases the wall shear stress. However, the larger the wall roughness, the greater the thickness of mud cake, which weakening the cementing strength. Considering the effects in a comprehensive way, it is discovered that the particle size of solid phase in drilling fluid is about 0.1 mm to get better cementing quality.

Three-dimensional structure of dominant instabilities in turbulent flow over smooth and rough boundaries

NASA Astrophysics Data System (ADS)

Grass, A. J.; Stuart, R. J.; Mansour-Tehrani, M.

1991-01-01

The current status of knowledge regarding coherent vortical structures in turbulent boundary layers and their role in turbulence generation are reviewed. The investigations reported in the study concentrate attention on rough-wall flows prevailing in the geophysical environment and include an experiment determining the three-dimensional form of the turbulence structures linked to the ejection and inrush events observed over rough walls and an experiment concerned with measuring the actual spanwise scale of the near-wall structures for boundary conditions ranging from hydrodynamically smooth to fully rough. It is demonstrated that horseshoe vortical structures are present and play an important role in rough-wall flows and they increase in scale with increasing wall distance, while a dominant spanwise wavelength occurs in the instantaneous cross-flow distribution of streamwise velocity close to the rough wall.

Pulsed Eddy Current Sensing for Critical Pipe Condition Assessment

PubMed Central

2017-01-01

Pulsed Eddy Current (PEC) sensing is used for Non-Destructive Evaluation (NDE) of the structural integrity of metallic structures in the aircraft, railway, oil and gas sectors. Urban water utilities also have extensive large ferromagnetic structures in the form of critical pressure pipe systems made of grey cast iron, ductile cast iron and mild steel. The associated material properties render NDE of these pipes by means of electromagnetic sensing a necessity. In recent years PEC sensing has established itself as a state-of-the-art NDE technique in the critical water pipe sector. This paper presents advancements to PEC inspection in view of the specific information demanded from water utilities along with the challenges encountered in this sector. Operating principles of the sensor architecture suitable for application on critical pipes are presented with the associated sensor design and calibration strategy. A Gaussian process-based approach is applied to model a functional relationship between a PEC signal feature and critical pipe wall thickness. A case study demonstrates the sensor’s behaviour on a grey cast iron pipe and discusses the implications of the observed results and challenges relating to this application. PMID:28954392

Systematic approach to in-depth understanding of photoelectrocatalytic bacterial inactivation mechanisms by tracking the decomposed building blocks.

PubMed

Sun, Hongwei; Li, Guiying; Nie, Xin; Shi, Huixian; Wong, Po-Keung; Zhao, Huijun; An, Taicheng

2014-08-19

A systematic approach was developed to understand, in-depth, the mechanisms involved during the inactivation of bacterial cells using photoelectrocatalytic (PEC) processes with Escherichia coli K-12 as the model microorganism. The bacterial cells were found to be inactivated and decomposed primarily due to attack from photogenerated H2O2. Extracellular reactive oxygen species (ROSs), such as H2O2, may penetrate into the bacterial cell and cause dramatically elevated intracellular ROSs levels, which would overwhelm the antioxidative capacity of bacterial protective enzymes such as superoxide dismutase and catalase. The activities of these two enzymes were found to decrease due to the ROSs attacks during PEC inactivation. Bacterial cell wall damage was then observed, including loss of cell membrane integrity and increased permeability, followed by the decomposition of cell envelope (demonstrated by scanning electronic microscope images). One of the bacterial building blocks, protein, was found to be oxidatively damaged due to the ROSs attacks, as well. Leakage of cytoplasm and biomolecules (bacterial building blocks such as proteins and nucleic acids) were evident during prolonged PEC inactivation process. The leaked cytoplasmic substances and cell debris could be further degraded and, ultimately, mineralized with prolonged PEC treatment.

Turbulence modifications in a turbulent boundary layer over a rough wall with spanwise-alternating roughness strips

NASA Astrophysics Data System (ADS)

Bai, H. L.; Kevin, Hutchins, N.; Monty, J. P.

2018-05-01

Turbulence modifications over a rough wall with spanwise-varying roughness are investigated at a moderate Reynolds number Reτ ≈ 2000 (or Reθ ≈ 6400), using particle image velocimetry (PIV) and hotwire anemometry. The rough wall is comprised of spanwise-alternating longitudinal sandpaper strips of two different roughness heights. The ratio of high- and low-roughness heights is 8, and the ratio of high- and low-roughness strip width is 0.5. PIV measurements are conducted in a wall-parallel plane located in the logarithmic region, while hotwire measurements are made throughout the entire boundary layer in a cross-stream plane. In a time-average sense, large-scale counter-rotating roll-modes are observed in the cross-stream plane over the rough wall, with downwash and upwash common-flows displayed over the high- and low-roughness strips, respectively. Meanwhile, elevated and reduced streamwise velocities occur over the high- and low-roughness strips, respectively. Significant modifications in the distributions of mean vorticities and Reynolds stresses are observed, exhibiting features of spatial preference. Furthermore, spatial correlations and conditional average analyses are performed to examine the alterations of turbulence structures over the rough wall, revealing that the time-invariant structures observed are resultant from the time-average process of instantaneous turbulent events that occur mostly and preferentially in space.

Effect of surface deposits on electromagnetic propagation in uniform ducts

NASA Technical Reports Server (NTRS)

Baumeister, Kenneth J.

1991-01-01

A finite-element Galerkin formulation has been used to study the effect of material surface deposits on the reflective characteristics of straight uniform ducts with PEC (perfectly electric conducting) walls. Over a wide frequency range, the effect of both single and multiple dielectric surface deposits on the duct reflection coefficient were examined. The power reflection coefficient was found to be significantly increased by the addition of deposits on the wall.

Investigation of secondary flows in turbulent pipe flows with three-dimensional sinusoidal walls

NASA Astrophysics Data System (ADS)

Chan, Leon; MacDonald, Michael; Chung, Daniel; Hutchins, Nicholas; Ooi, Andrew

2017-11-01

The occurrence of secondary flows is systematically investigated via Direct Numerical Simulations (DNS) of turbulent flow in a rough wall pipe at friction Reynolds numbers of 540. In this study, the peak-to-trough height of the roughness elements, which consist of three-dimensional sinusoidal roughness, is fixed at 120 viscous units while the wavelength of the roughness elements is varied. The solidity or effective slope (ES) of the roughness ranges from the sparse regime (ES = 0.18) to the closely packed roughness/dense regime (ES = 0.72). The time-independent dispersive stresses, which arise due to the stationary features of the flow, are analysed and are found to increase with increasing roughness wavelength. These dispersive stresses are related to the occurrence of secondary flows and are maximum within the roughness canopy. Above the crest of the roughness elements, the dispersive stresses reduce to zero at wall-normal heights greater than half of the roughness wavelength. This study has found that the size and wall-normal extent of the secondary flows scales with the roughness wavelength and can reach wall-normal heights of almost half of the pipe radius.

Scale resolving computation of submerged wall jets on flat wall with different roughness heights

NASA Astrophysics Data System (ADS)

Paik, Joongcheol; Bombardelli, Fabian

2014-11-01

Scale-adaptive simulation is used to investigate the response of velocity and turbulence in submerged wall jets to abrupt changes from smooth to rough beds. The submerged wall jets were experimentally investigated by Dey and Sarkar [JFM, 556, 337, 2006] at the Reynolds number of 17500 the Froude number of 4.09 and the submergence ratio of 1.12 on different rough beds that were generated by uniform sediments of different median diameters The SAS is carried out by means of a second-order-accurate finite volume method in space and time and the effect of bottom roughness is treated by the approach of Cebeci (2004). The evolution of free surface is captured by employing the two-phase volume of fluid (VOF) technique. The numerical results obtained by the SAS approach, incorporated with the VOF and the rough wall treatment, are in good agreement with the experimental measurements. The computed turbulent boundary layer grows more quickly and the depression of the free surface is more increased on the rough wall than those on smooth wall. The size of the fully developed zone shrinks and the decay rate of maximum streamwise velocity and Reynolds stress components are faster with increase in the wall roughness. Supported by NSF and NRF of Korea.

Scale growth of structures in the turbulent boundary layer with a rod-roughened wall

NASA Astrophysics Data System (ADS)

Lee, Jin; Kim, Jung Hoon; Lee, Jae Hwa

2016-01-01

Direct numerical simulation of a turbulent boundary layer over a rod-roughened wall is performed with a long streamwise domain to examine the streamwise-scale growth mechanism of streamwise velocity fluctuating structures in the presence of two-dimensional (2-D) surface roughness. An instantaneous analysis shows that there is a slightly larger population of long structures with a small helix angle (spanwise inclinations relative to streamwise) and a large spanwise width over the rough-wall compared to that over a smooth-wall. Further inspection of time-evolving instantaneous fields clearly exhibits that adjacent long structures combine to form a longer structure through a spanwise merging process over the rough-wall; moreover, spanwise merging for streamwise scale growth is expected to occur frequently over the rough-wall due to the large spanwise scales generated by the 2-D roughness. Finally, we examine the influence of a large width and a small helix angle of the structures over the rough-wall with regard to spatial two-point correlation. The results show that these factors can increase the streamwise coherence of the structures in a statistical sense.

Ray Tracing and Modal Methods for Modeling Radio Propagation in Tunnels With Rough Walls

PubMed Central

Zhou, Chenming

2017-01-01

At the ultrahigh frequencies common to portable radios, tunnels such as mine entries are often modeled by hollow dielectric waveguides. The roughness condition of the tunnel walls has an influence on radio propagation, and therefore should be taken into account when an accurate power prediction is needed. This paper investigates how wall roughness affects radio propagation in tunnels, and presents a unified ray tracing and modal method for modeling radio propagation in tunnels with rough walls. First, general analytical formulas for modeling the influence of the wall roughness are derived, based on the modal method and the ray tracing method, respectively. Second, the equivalence of the ray tracing and modal methods in the presence of wall roughnesses is mathematically proved, by showing that the ray tracing-based analytical formula can converge to the modal-based formula through the Poisson summation formula. The derivation and findings are verified by simulation results based on ray tracing and modal methods. PMID:28935995

Smooth- and rough-wall boundary layer structure from high spatial range particle image velocimetry

NASA Astrophysics Data System (ADS)

Squire, D. T.; Morrill-Winter, C.; Hutchins, N.; Marusic, I.; Schultz, M. P.; Klewicki, J. C.

2016-10-01

Two particle image velocimetry arrangements are used to make true spatial comparisons between smooth- and rough-wall boundary layers at high Reynolds numbers across a very wide range of streamwise scales. Together, the arrangements resolve scales ranging from motions on the order of the Kolmogorov microscale to those longer than twice the boundary layer thickness. The rough-wall experiments were obtained above a continuous sandpaper sheet, identical to that used by Squire et al. [J. Fluid Mech. 795, 210 (2016), 10.1017/jfm.2016.196], and cover a range of friction and equivalent sand-grain roughness Reynolds numbers (12 000 ≲δ+≲ 18000, 62 ≲ks+≲104 ). The smooth-wall experiments comprise new and previously published data spanning 6500 ≲δ+≲17 000 . Flow statistics from all experiments show similar Reynolds number trends and behaviors to recent, well-resolved hot-wire anemometry measurements above the same rough surface. Comparisons, at matched δ+, between smooth- and rough-wall two-point correlation maps and two-point magnitude-squared coherence maps demonstrate that spatially the outer region of the boundary layer is the same between the two flows. This is apparently true even at wall-normal locations where the total (inner-normalized) energy differs between the smooth and rough wall. Generally, the present results provide strong support for Townsend's [The Structure of Turbulent Shear Flow (Cambridge University Press, Cambridge, 1956), Vol. 1] wall-similarity hypothesis in high Reynolds number fully rough boundary layer flows.

Irregular wall roughness in turbulent Taylor-Couette flow

NASA Astrophysics Data System (ADS)

Berghout, Pieter; Zhu, Xiaojue; Verzicco, Roberto; Lohse, Detlef; Stevens, Richard

2017-11-01

Many wall bounded flows in nature, engineering and transport are affected by surface roughness. Often, this has adverse effects, e.g. drag increase leading to higher energy costs. A major difficulty is the infinite number of roughness geometries, which makes it impossible to systematically investigate all possibilities. Here we present Direct Numerical Simulations (DNS) of turbulent Taylor-Couette flow. We focus on the transitionally rough regime, in which both viscous and pressure forces contribute to the total wall stress. We investigate the effect of the mean roughness height and the effective slope on the roughness function, ΔU+ . Also, we present simulations of varying Ta (Re) numbers for a constant mean roughness height (kmean+). Alongside, we show the behavior of the large scale structures (e.g. plume ejection, Taylor rolls) and flow structures in the vicinity of the wall.

Progress Towards an LES Wall Model Including Unresolved Roughness

NASA Astrophysics Data System (ADS)

Craft, Kyle; Redman, Andrew; Aikens, Kurt

2015-11-01

Wall models used in large eddy simulations (LES) are often based on theories for hydraulically smooth walls. While this is reasonable for many applications, there are also many where the impact of surface roughness is important. A previously developed wall model has been used primarily for jet engine aeroacoustics. However, jet simulations have not accurately captured thick initial shear layers found in some experimental data. This may partly be due to nozzle wall roughness used in the experiments to promote turbulent boundary layers. As a result, the wall model is extended to include the effects of unresolved wall roughness through appropriate alterations to the log-law. The methodology is tested for incompressible flat plate boundary layers with different surface roughness. Correct trends are noted for the impact of surface roughness on the velocity profile. However, velocity deficit profiles and the Reynolds stresses do not collapse as well as expected. Possible reasons for the discrepancies as well as future work will be presented. This work used the Extreme Science and Engineering Discovery Environment (XSEDE), which is supported by National Science Foundation grant number ACI-1053575. Computational resources on TACC Stampede were provided under XSEDE allocation ENG150001.

Investigation of wall-bounded turbulence over sparsely distributed roughness

NASA Astrophysics Data System (ADS)

Placidi, Marco; Ganapathisubramani, Bharath

2011-11-01

The effects of sparsely distributed roughness elements on the structure of a turbulent boundary layer are examined by performing a series of Particle Image Velocimetry (PIV) experiments in a wind tunnel. From the literature, the best way to characterise a rough wall, especially one where the density of roughness elements is sparse, is unclear. In this study, rough surfaces consisting of sparsely and uniformly distributed LEGO® blocks are used. Five different patterns are adopted in order to examine the effects of frontal solidity (λf, frontal area of the roughness elements per unit wall-parallel area), plan solidity (λp, plan area of roughness elements per unit wall-parallel area) and the geometry of the roughness element (square and cylindrical elements), on the turbulence structure. The Karman number, Reτ , has been matched, at the value of approximately 2300, in order to compare across the different cases. In the talk, we will present detailed analysis of mean and rms velocity profiles, Reynolds stresses and quadrant decomposition.

Picosecond time-resolved photoluminescence using picosecond excitation correlation spectroscopy

NASA Astrophysics Data System (ADS)

Johnson, M. B.; McGill, T. C.; Hunter, A. T.

1988-03-01

We present a study of the temporal decay of photoluminescence (PL) as detected by picosecond excitation correlation spectroscopy (PECS). We analyze the correlation signal that is obtained from two simple models; one where radiative recombination dominates, the other where trapping processes dominate. It is found that radiative recombination alone does not lead to a correlation signal. Parallel trapping type processes are found to be required to see a signal. To illustrate this technique, we examine the temporal decay of the PL signal for In-alloyed, semi-insulating GaAs substrates. We find that the PL signal indicates a carrier lifetime of roughly 100 ps, for excitation densities of 1×1016-5×1017 cm-3. PECS is shown to be an easy technique to measure the ultrafast temporal behavior of PL processes because it requires no ultrafast photon detection. It is particularly well suited to measuring carrier lifetimes.

Enhanced photoelectrochemical water splitting by oxides heterojunction photocathode coupled with Ag.

PubMed

Lu, Xue; Liu, Zhifeng

2017-08-14

A novel one-dimensional Co 3 O 4 /CuO/Ag composite structure film was directly grown on indium tin oxide glass substrate by a simple hydrothermal method and electrodeposition method. The film was employed for the first time as a photocathode for photoelectrochemical (PEC) water splitting to generate hydrogen. The photocurrent density of the Co 3 O 4 /CuO/Ag composite structure achieved -5.13 mA cm -2 at -0.2 V vs. RHE, which is roughly 12.8 times that of 1D Co 3 O 4 nanowires and 3.31 times Co 3 O 4 /CuO heterojunction photocathodes. The enhanced PEC performance of this Co 3 O 4 /CuO/Ag composite structure ascribes increased light-harvesting and light-absorption, distensible photoresponse range, decreased interface charge transfer resistance, and improved photogenerated electron-hole pairs transfer and separation.

Large-Eddy Simulations of Fully Developed Turbulent Channel and Pipe Flows with Smooth and Rough Walls

NASA Astrophysics Data System (ADS)

Saito, Namiko

Studies in turbulence often focus on two flow conditions, both of which occur frequently in real-world flows and are sought-after for their value in advancing turbulence theory. These are the high Reynolds number regime and the effect of wall surface roughness. In this dissertation, a Large-Eddy Simulation (LES) recreates both conditions over a wide range of Reynolds numbers Retau = O(102) - O(108) and accounts for roughness by locally modeling the statistical effects of near-wall anisotropic fine scales in a thin layer immediately above the rough surface. A subgrid, roughness-corrected wall model is introduced to dynamically transmit this modeled information from the wall to the outer LES, which uses a stretched-vortex subgrid-scale model operating in the bulk of the flow. Of primary interest is the Reynolds number and roughness dependence of these flows in terms of first and second order statistics. The LES is first applied to a fully turbulent uniformly-smooth/rough channel flow to capture the flow dynamics over smooth, transitionally rough and fully rough regimes. Results include a Moody-like diagram for the wall averaged friction factor, believed to be the first of its kind obtained from LES. Confirmation is found for experimentally observed logarithmic behavior in the normalized stream-wise turbulent intensities. Tight logarithmic collapse, scaled on the wall friction velocity, is found for smooth-wall flows when Re tau ≥ O(106) and in fully rough cases. Since the wall model operates locally and dynamically, the framework is used to investigate non-uniform roughness distribution cases in a channel, where the flow adjustments to sudden surface changes are investigated. Recovery of mean quantities and turbulent statistics after transitions are discussed qualitatively and quantitatively at various roughness and Reynolds number levels. The internal boundary layer, which is defined as the border between the flow affected by the new surface condition and the unaffected part, is computed, and a collapse of the profiles on a length scale containing the logarithm of friction Reynolds number is presented. Finally, we turn to the possibility of expanding the present framework to accommodate more general geometries. As a first step, the whole LES framework is modified for use in the curvilinear geometry of a fully-developed turbulent pipe flow, with implementation carried out in a spectral element solver capable of handling complex wall profiles. The friction factors have shown favorable agreement with the superpipe data, and the LES estimates of the Karman constant and additive constant of the log-law closely match values obtained from experiment.

Examination of biogenic selenium-containing nanosystems based on polyelectrolyte complexes by atomic force, Kelvin probe force and electron microscopy methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sukhanova, T. E., E-mail: tat-sukhanova@mail.ru; Vylegzhanina, M. E.; Valueva, S. V.

The morphology and electrical properties of biogenic selenium-containing nanosystems based on polyelectrolyte complexes (PECs) were examined using AFM, Kelvin Probe Force and electron microscopy methods. It has been found, that prepared nanostructures significantly differed in their morphological types and parameters. In particular, multilayers capsules can be produced via varying synthesis conditions, especially, the selenium–PEC mass ratio ν. At the “special point” (ν = 0.1), filled and hollow nano- and microcapsules are formed in the system. The multilayer character of the capsules walls is visible in the phase images. Kelvin Probe Force images showed the inhomogeneity of potential distribution in capsulesmore » and outside them.« less

Effective field model of roughness in magnetic nano-structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lepadatu, Serban, E-mail: SLepadatu@uclan.ac.uk

2015-12-28

An effective field model is introduced here within the micromagnetics formulation, to study roughness in magnetic structures, by considering sub-exchange length roughness levels as a perturbation on a smooth structure. This allows the roughness contribution to be separated, which is found to give rise to an effective configurational anisotropy for both edge and surface roughness, and accurately model its effects with fine control over the roughness depth without the explicit need to refine the computational cell size to accommodate the roughness profile. The model is validated by comparisons with directly roughened structures for a series of magnetization switching and domainmore » wall velocity simulations and found to be in excellent agreement for roughness levels up to the exchange length. The model is further applied to vortex domain wall velocity simulations with surface roughness, which is shown to significantly modify domain wall movement and result in dynamic pinning and stochastic creep effects.« less

Surface roughness effects on turbulent Couette flow

NASA Astrophysics Data System (ADS)

Lee, Young Mo; Lee, Jae Hwa

2017-11-01

Direct numerical simulation of a turbulent Couette flow with two-dimensional (2-D) rod roughness is performed to examine the effects of the surface roughness. The Reynolds number based on the channel centerline laminar velocity (Uco) and channel half height (h) is Re =7200. The 2-D rods are periodically arranged with a streamwise pitch of λ = 8 k on the bottom wall, and the roughness height is k = 0.12 h. It is shown that the wall-normal extent for the logarithmic layer is significantly shortened in the rough-wall turbulent Couette flow, compared to a turbulent Couette flow with smooth wall. Although the Reynolds stresses are increased in a turbulent channel flow with surface roughness in the outer layer due to large-scale ejection motions produced by the 2-D rods, those of the rough-wall Couette flow are decreased. Isosurfaces of the u-structures averaged in time suggest that the decrease of the turbulent activity near the centerline is associated with weakened large-scale counter-rotating roll modes by the surface roughness. This research was supported by the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2017R1D1A1A09000537) and the Ministry of Science, ICT & Future Planning (NRF-2017R1A5A1015311).

Investigation of Wall Shear Stress Behavior for Rough Surfaces with Blowing

NASA Astrophysics Data System (ADS)

Helvey, Jacob; Borchetta, Colby; Miller, Mark; Martin, Alexandre; Bailey, Sean

2014-11-01

We present an experimental study conducted in a turbulent channel flow wind tunnel to determine the modifications made to the turbulent flow over rough surfaces with flow injection through the surfaces. Hot-wire profile results from a quasi-two-dimensional, sinusoidally-rough surface indicate that the effects of roughness are enhanced by momentum injection through the surface. In particular, the wall shear stress was found to show behavior consistent with increased roughness height when surface blowing was increased. This observed behavior contradicts previously reported results for regular three-dimensional roughness which show a decrease in wall shear stress with additional blowing. It is unclear whether this discrepancy is due to differences in the roughness geometry under consideration or the use of the Clauser fit to estimate wall shear stress. Additional PIV experiments are being conducted for a three-dimensional fibrous surface to obtain Reynolds shear stress profiles. These results provide an additional method for estimation of wall-shear stress and thus allow verification of the use of the Clauser chart approach for flows with momentum injection through the surface. This research is supported by NASA Kentucky EPSCoR Award NNX10AV39A, and NASA RA Award NNX13AN04A.

Investigation of wall-bounded turbulence over regularly distributed roughness

NASA Astrophysics Data System (ADS)

Placidi, Marco; Ganapathisubramani, Bharathram

2012-11-01

The effects of regularly distributed roughness elements on the structure of a turbulent boundary layer are examined by performing a series of Planar (high resolution l+ ~ 30) and Stereoscopic Particle Image Velocimetry (PIV) experiments in a wind tunnel. An adequate description of how to best characterise a rough wall, especially one where the density of roughness elements is sparse, is yet to be developed. In this study, rough surfaces consisting of regularly and uniformly distributed LEGO® blocks are used. Twelve different patterns are adopted in order to systematically examine the effects of frontal solidity (λf, frontal area of the roughness elements per unit wall-parallel area) and plan solidity (λp, plan area of roughness elements per unit wall-parallel area), on the turbulence structure. The Karman number, Reτ , is approximately 4000 across the different cases. Spanwise 3D vector fields at two different wall-normal locations (top of the canopy and within the log-region) are also compared to examine the spanwise homogeneity of the flow across different surfaces. In the talk, a detailed analysis of mean and rms velocity profiles, Reynolds stresses, and quadrant decomposition for the different patterns will be presented.

Integrated MoSe2 with n+p-Si photocathodes for solar water splitting with high efficiency and stability

NASA Astrophysics Data System (ADS)

Huang, Guanping; Mao, Jie; Fan, Ronglei; Yin, Zhihao; Wu, Xi; Jie, Jiansheng; Kang, Zhenhui; Shen, Mingrong

2018-01-01

Many earth-abundant transition metal dichalcogenides (TMDs) have been employed as catalysts for H2 evolution reaction (HER); however, their impactful integration onto photocathodes for photoelectrochemical (PEC) HER is less developed. In this study, we directly sputtered a MoSe2 catalyst onto an n+p-Si photocathode for efficient and stable PEC-HER. An onset potential of 0.4 V vs. RHE, a saturated photocurrent of 29.3 mA/cm2, a fill factor of 0.32, and an energy conversion efficiency of 3.8% were obtained under 100 mA/cm2 Xe lamp illumination. Such superior PEC properties were ascribed to the nearly vertically standing two dimensional MoSe2 rough surface layer and the sharp interface between Si and MoSe2 with small charge transfer resistance. The balance between the reflectivity of the electrode surface and the absorptivity of MoSe2 was also discussed. In addition, the MoSe2 layer can protect the n+p-Si photocathode with a 120 h stability due to its initial growth on Si with high flatness and compactness. This study provides a path to the effective and scalable growth of TMDs onto the Si photocathode aiming for high efficiency and stability.

Andreas Acrivos Dissertation Award Talk: Modeling drag forces and velocity fluctuations in wall-bounded flows at high Reynolds numbers

NASA Astrophysics Data System (ADS)

Yang, Xiang

2017-11-01

The sizes of fluid motions in wall-bounded flows scale approximately as their distances from the wall. At high Reynolds numbers, resolving near-wall, small-scale, yet momentum-transferring eddies are computationally intensive, and to alleviate the strict near-wall grid resolution requirement, a wall model is usually used. The wall model of interest here is the integral wall model. This model parameterizes the near-wall sub-grid velocity profile as being comprised of a linear inner-layer and a logarithmic meso-layer with one additional term that accounts for the effects of flow acceleration, pressure gradients etc. We use the integral wall model for wall-modeled large-eddy simulations (WMLES) of turbulent boundary layers over rough walls. The effects of rough-wall topology on drag forces are investigated. A rough-wall model is then developed based on considerations of such effects, which are now known as mutual sheltering among roughness elements. Last, we discuss briefly a new interpretation of the Townsend attached eddy hypothesis-the hierarchical random additive process model (HRAP). The analogy between the energy cascade and the momentum cascade is mathematically formal as HRAP follows the multi-fractal formulism, which was extensively used for the energy cascade.

A note on ``critical roughness height'' and ``transitional roughness''

NASA Astrophysics Data System (ADS)

Bradshaw, P.

2000-06-01

An unrigorous but plausible analysis suggests that the concept of a critical roughness height, below which roughness does not affect a turbulent wall flow, is erroneous. The Oseen approximation implies that the effect of roughness on the additive constant in the logarithmic law of the wall should vary as the square of the roughness Reynolds number (specifically the roughness height in "wall units"). This is an important point in determining whether surfaces used in experiments at high unit Reynolds number can be regarded as hydraulically smooth. Attention is also called to the qualitative difference between Nikuradse's measurements of friction factor in pipe flow with uniform-size sand-grain roughness in the "transitional" range of Reynolds number and the data correlation in the Moody chart of 1944; the latter was derived from tests on miscellaneous real-life rough surfaces in the 1930s. Nearly all textbooks on elementary fluid dynamics present, but practically none discuss, this difference. Nikuradse's monodisperse roughness is a very rare case with untypical behavior in the transitional range.

Visible-light driven photoelectrochemical immunosensor for insulin detection based on MWCNTs@SnS2@CdS nanocomposites.

PubMed

Liu, Yixin; Zhang, Yifeng; Wu, Dan; Fan, Dawei; Pang, Xuehui; Zhang, Yong; Ma, Hongmin; Sun, Xu; Wei, Qin

2016-12-15

In this work, a label-free photoelectrochemical (PEC) immunosensor was developed for ultrasensitive detection of insulin based on MWCNTs@SnS2@CdS nanocomposites. As graphene-like 2D nanomaterial, SnS2 nanosheets loaded on the conducting framework of multi-walled carbon nanotubes (MWCNTs) were adopted for the construction of immunosensor for the first time, providing a favorable substrate for in-situ growth of CdS nanocrystal that had suitable band structure matching well with SnS2. The well-matched band structure of these two metal sulfides effectively inhibited the recombination of photogenerated electron-hole pairs, thus improving the photo-to-current conversion efficiency. Besides, the introduction of MWCNTs facilitated electron transfer across the surface of electrodes, leading to a further increment of photocurrent. The as constructed label-free PEC immunosensor based on MWCNTs@SnS2@CdS nanocomposites exhibited excellent PEC performance for the detection of insulin. The concentrations of insulin could be directly detected based on the decrement of photocurrent that was brought by the increased steric hindrances due to the formation of antigen-antibody immunocomplexes. Under the optimal conditions, the PEC immunosensor had a sensitive response to insulin in a linear range of 0.1pgmL(-1) to 5ngmL(-1) with a detection limit of 0.03pgmL(-1). Meanwhile, good stability and selectivity were achieved as well. The design and fabrication of this PEC immunosensor based on MWCNTs@SnS2@CdS nanocomposites not only provided an ideal platform for the detection of insulin, but also opened up a new avenue for the development of immunosensor for some other biomarkers analysis. Copyright © 2016 Elsevier B.V. All rights reserved.

Molecular dynamic simulation of Ar-Kr mixture across a rough walled nanochannel: Velocity and temperature profiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pooja,, E-mail: pupooja16@gmail.com; Ahluwalia, P. K., E-mail: pk-ahluwalia7@yahoo.com; Pathania, Y.

2015-05-15

This paper presents the results from a molecular dynamics simulation of mixture of argon and krypton in the Poiseuille flow across a rough walled nanochannel. The roughness effect on liquid nanoflows has recently drawn attention The computational software used for carrying out the molecular dynamics simulations is LAMMPS. The fluid flow takes place between two parallel plates and is bounded by horizontal rough walls in one direction and periodic boundary conditions are imposed in the other two directions. Each fluid atom interacts with other fluid atoms and wall atoms through Leenard-Jones (LJ) potential with a cut off distance of 5.0.more » To derive the flow a constant force is applied whose value is varied from 0.1 to 0.3 and velocity profiles and temperature profiles are noted for these values of forces. The velocity profile and temperature profiles are also looked at different channel widths of nanochannel and at different densities of mixture. The velocity profile and temperature profile of rough walled nanochannel are compared with that of smooth walled nanochannel and it is concluded that mean velocity increases with increase in channel width, force applied and decrease in density also with introduction of roughness in the walls of nanochannel mean velocity again increases and results also agree with the analytical solution of a Poiseuille flow.« less

Molecular dynamic simulation of Ar-Kr mixture across a rough walled nanochannel: Velocity & temperature profiles

NASA Astrophysics Data System (ADS)

Pooja, Pathania, Y.; Ahluwalia, P. K.

2015-05-01

This paper presents the results from a molecular dynamics simulation of mixture of argon and krypton in the Poiseuille flow across a rough walled nanochannel. The roughness effect on liquid nanoflows has recently drawn attention The computational software used for carrying out the molecular dynamics simulations is LAMMPS. The fluid flow takes place between two parallel plates and is bounded by horizontal rough walls in one direction and periodic boundary conditions are imposed in the other two directions. Each fluid atom interacts with other fluid atoms and wall atoms through Leenard-Jones (LJ) potential with a cut off distance of 5.0. To derive the flow a constant force is applied whose value is varied from 0.1 to 0.3 and velocity profiles and temperature profiles are noted for these values of forces. The velocity profile and temperature profiles are also looked at different channel widths of nanochannel and at different densities of mixture. The velocity profile and temperature profile of rough walled nanochannel are compared with that of smooth walled nanochannel and it is concluded that mean velocity increases with increase in channel width, force applied and decrease in density also with introduction of roughness in the walls of nanochannel mean velocity again increases and results also agree with the analytical solution of a Poiseuille flow.

On the receptivity problem for Goertler vortices: Vortex motions induced by wall roughness

NASA Technical Reports Server (NTRS)

Denier, James P.; Hall, Philip; Seddougui, Sharon

1990-01-01

The receptivity problem for Goertler vortices induced by wall roughness is investigated. The roughness is modelled by small amplitude perturbations to the curved wall over which the flow takes place. The amplitude of these perturbations is taken to be sufficiently small for the induced Goertler vortices to be described by linear theory. The roughness is assumed to vary in the spanwise direction on the boundary layer lengthscale, while in the flow direction the corresponding variation is on the lengthscale over which the wall curvature varies. In fact the latter condition can be relaxed to allow for a faster streamwise roughness variation so long as the variation does not become as fast as that in the spanwise direction. The function which describes the roughness is assumed to be such that its spanwise and streamwise dependences can be separated; this enables progress by taking Fourier or Laplace transforms where appropriate. The cases of isolated and distributed roughness elements are investigated and the coupling coefficient which relates the amplitude of the forcing and the induced vortex amplitude is found asymptotically in the small wavelength limit. It is shown that this coefficient is exponentially small in the latter limit so that it is unlikely that this mode can be stimulated directly by wall roughness. The situation at 0(1) wavelengths is quite different and this is investigated numerically for different forcing functions. It is found that an isolated roughness element induces a vortex field which grows within a wedge at a finite distance downstream of the element. However, immediately downstream of the obstacle the disturbed flow produced by the element decays in amplitude. The receptivity problem at larger Goertler numbers appropriate to relatively large wall curvature is discussed in detail.

Role of rough surface topography on gas slip flow in microchannels.

PubMed

Zhang, Chengbin; Chen, Yongping; Deng, Zilong; Shi, Mingheng

2012-07-01

We conduct a lattice Boltzmann simulation of gas slip flow in microchannels incorporating rough surface effects as characterized by fractal geometry with a focus on gas-solid interaction. The gas slip flow in rough microchannels, which is characterized by Poiseuille number and mass flow rate, is evaluated and compared with smooth microchannels. The effects of roughness height, surface fractal dimension, and Knudsen number on slip behavior of gas flow in microchannels are all investigated and discussed. The results indicate that the presence of surface roughness reduces boundary slip for gas flow in microchannels with respect to a smooth surface. The gas flows at the valleys of rough walls are no-slip while velocity slips are observed over the top of rough walls. We find that the gas flow behavior in rough microchannels is insensitive to the surface topography irregularity (unlike the liquid flow in rough microchannels) but is influenced by the statistical height of rough surface and rarefaction effects. In particular, decrease in roughness height or increase in Knudsen number can lead to large wall slip for gas flow in microchannels.

PecS regulates the urate-responsive expression of type 1 fimbriae in Klebsiella pneumoniae CG43.

PubMed

Wang, Zhe-Chong; Liu, Chia-Jui; Huang, Ying-Jung; Wang, Yu-Seng; Peng, Hwei-Ling

2015-12-01

In the Klebsiella pneumoniae CG43 genome, the divergently transcribed genes coding for PecS, the MarR-type transcription factor, and PecM, the drug metabolite transporter, are located between the type 1 and type 3 fimbrial gene clusters. The intergenic sequence pecO between pecS and pecM contains three putative PecS binding sites and a CpxR box. Electrophoretic mobility shift assay revealed that the recombinant PecS and CpxR could specifically bind to the pecO sequence, and the specific interaction of PecS and pecO could be attenuated by urate. The expression of pecS and pecM was negatively regulated by CpxAR and PecS, and was inducible by exogenous urate in the absence of cpxAR. Compared with CG43S3ΔcpxAR, the derived mutants CG43S3ΔcpxARΔpecS and CG43S3ΔcpxARΔpecSΔpecM exerted similar levels of sensitivity to H2O2 or paraquat, but higher levels of mannose-sensitive yeast agglutination activity and FimA production. The promoter activity and transcript levels of fimA in CG43S3ΔcpxAR were also increased by deleting pecS. However, no binding activity between PecS and the fimA promoter could be observed. Nevertheless, PecS deletion could reduce the expression of the global regulator HNS and release the negative effect of HNS on FimA expression. In CG43S3ΔcpxAR, the expression of FimA as well as PecS was inducible by urate, whilst urate-induced FimA expression was inhibited by the deletion of pecS. Taken together, we propose that K. pneumoniae PecS indirectly and negatively regulates the expression of type 1 fimbriae, and the regulation is urate-inducible in the absence of CpxAR.

Rough-Wall Channel Analysis Using Suboptimal Control Theory

NASA Technical Reports Server (NTRS)

Flores, O.; Jimenez, J.; Tenpleton, J.

2003-01-01

The original aim of this work was to shed some light on the physics of turbulence over rough walls using large-eddy simulations and the suboptimal-control wall boundary conditions introduced by Nicoud et al. It was hoped that, if that algorithm was used to fit the mean velocity profile of the simulations to that of a rough-walled channel, instead of to a smooth one, the wall stresses introduced by the control algorithm would give some indication of what aspects of rough walls are most responsible for the modification of the flow in real turbulence. It was similarly expected that the structure of the resulting velocity fluctuations would share some of the characteristics of rough-walled flows, thus again suggesting what is intrinsic and what is accidental in the effect of geometric wall roughness. A secondary goal was to study the effect of 'unphysical' boundary conditions on the outside flow by observing how a relatively major change of the target velocity profile, and therefore presumably of the applied wall stresses, modifies properties such as the dominant length scales of the velocity fluctuations away from the wall. As will be seen below, this secondary goal grew more important during the course of the study, which was carried out during a short summer visit of the first two authors to the CTR. It became clear that there are open questions about the way in which the control algorithm models the boundary conditions, even for smooth walls, and that these questions make the physical interpretation of the results difficult. Considerable more work in that area seems to be needed before even relatively advanced large-eddy simulations, such as these, can be used to draw conclusions about the physics of wall-bounded turbulent flows. The numerical method is the same as in Nicoud et al. The modifications introduced in the original code are briefly described in section 2, but the original paper should be consulted for a full description of the algorithm. The results are presented in section 3 and summarized in section 4. The elementary properties of turbulence over rough walls which are used in the text have been taken from recent reviews such as Raupach et al. or Jimenez.

Nozzle wall roughness effects on free-stream noise and transition in the pilot low-disturbance tunnel

NASA Technical Reports Server (NTRS)

Creel, T. R., Jr.; Beckwith, I. E.; Chen, F. J.

1985-01-01

An investigation at Mach 3.5 into the effects of nozzle wall roughness on free stream pressure fluctuations and cone transition Reynolds numbers was conducted in the pilot low disturbance tunnel at the Langley Research Center. Nozzle wall roughness caused by either particle deposits or imperfections in surface finish increased free stream noise levels and reduced the transition Reynolds numbers on a cone mounted in the test rhombus.

Streptomyces coelicolor encodes a urate-responsive transcriptional regulator with homology to PecS from plant pathogens.

PubMed

Huang, Hao; Mackel, Brian J; Grove, Anne

2013-11-01

Many transcriptional regulators control gene activity by responding to specific ligands. Members of the multiple-antibiotic resistance regulator (MarR) family of transcriptional regulators feature prominently in this regard, and they frequently function as repressors in the absence of their cognate ligands. Plant pathogens such as Dickeya dadantii encode a MarR homolog named PecS that controls expression of a gene encoding the efflux pump PecM in addition to other virulence genes. We report here that the soil bacterium Streptomyces coelicolor also encodes a PecS homolog (SCO2647) that regulates a pecM gene (SCO2646). S. coelicolor PecS, which exists as a homodimer, binds the intergenic region between pecS and pecM genes with high affinity. Several potential PecS binding sites were found in this intergenic region. The binding of PecS to its target DNA can be efficiently attenuated by the ligand urate, which also quenches the intrinsic fluorescence of PecS, indicating a direct interaction between urate and PecS. In vivo measurement of gene expression showed that activity of pecS and pecM genes is significantly elevated after exposure of S. coelicolor cultures to urate. These results indicate that S. coelicolor PecS responds to the ligand urate by attenuated DNA binding in vitro and upregulation of gene activity in vivo. Since production of urate is associated with generation of reactive oxygen species by xanthine dehydrogenase, we propose that PecS functions under conditions of oxidative stress.

Streptomyces coelicolor Encodes a Urate-Responsive Transcriptional Regulator with Homology to PecS from Plant Pathogens

PubMed Central

Huang, Hao; Mackel, Brian J.

2013-01-01

Many transcriptional regulators control gene activity by responding to specific ligands. Members of the multiple-antibiotic resistance regulator (MarR) family of transcriptional regulators feature prominently in this regard, and they frequently function as repressors in the absence of their cognate ligands. Plant pathogens such as Dickeya dadantii encode a MarR homolog named PecS that controls expression of a gene encoding the efflux pump PecM in addition to other virulence genes. We report here that the soil bacterium Streptomyces coelicolor also encodes a PecS homolog (SCO2647) that regulates a pecM gene (SCO2646). S. coelicolor PecS, which exists as a homodimer, binds the intergenic region between pecS and pecM genes with high affinity. Several potential PecS binding sites were found in this intergenic region. The binding of PecS to its target DNA can be efficiently attenuated by the ligand urate, which also quenches the intrinsic fluorescence of PecS, indicating a direct interaction between urate and PecS. In vivo measurement of gene expression showed that activity of pecS and pecM genes is significantly elevated after exposure of S. coelicolor cultures to urate. These results indicate that S. coelicolor PecS responds to the ligand urate by attenuated DNA binding in vitro and upregulation of gene activity in vivo. Since production of urate is associated with generation of reactive oxygen species by xanthine dehydrogenase, we propose that PecS functions under conditions of oxidative stress. PMID:23995633

Optimization of Surface Roughness and Wall Thickness in Dieless Incremental Forming Of Aluminum Sheet Using Taguchi

NASA Astrophysics Data System (ADS)

Hamedon, Zamzuri; Kuang, Shea Cheng; Jaafar, Hasnulhadi; Azhari, Azmir

2018-03-01

Incremental sheet forming is a versatile sheet metal forming process where a sheet metal is formed into its final shape by a series of localized deformation without a specialised die. However, it still has many shortcomings that need to be overcome such as geometric accuracy, surface roughness, formability, forming speed, and so on. This project focus on minimising the surface roughness of aluminium sheet and improving its thickness uniformity in incremental sheet forming via optimisation of wall angle, feed rate, and step size. Besides, the effect of wall angle, feed rate, and step size to the surface roughness and thickness uniformity of aluminium sheet was investigated in this project. From the results, it was observed that surface roughness and thickness uniformity were inversely varied due to the formation of surface waviness. Increase in feed rate and decrease in step size will produce a lower surface roughness, while uniform thickness reduction was obtained by reducing the wall angle and step size. By using Taguchi analysis, the optimum parameters for minimum surface roughness and uniform thickness reduction of aluminium sheet were determined. The finding of this project helps to reduce the time in optimising the surface roughness and thickness uniformity in incremental sheet forming.

Diffusion of Drag-Reducing Polymers within a High-Reynolds-Number, Rough-Wall Turbulent Boundary Layer

NASA Astrophysics Data System (ADS)

Elbing, Brian; Perlin, Marc; Dowling, David; Solomon, Michael; Ceccio, Steven

2008-11-01

Two experiments were conducted to investigate polymer drag reduction (PDR) within high Reynolds number (to 200 million based on downstream distance), rough-wall turbulent boundary layers. The first experiment was conducted at the U.S. Navy's Large Cavitation Channel on a 12.9 m long flat-plate at speeds to 20 m/s with the surface hydraulically smooth and fully rough. Local skin-friction measurements on the smooth and rough surfaces had maximum PDR levels of 65 and 75 percent, respectively. However, PDR decreased with increasing downstream distance and flow speed more rapidly on the rough surface, and at the top speed no measureable level of PDR was observed. The roughness-induced increased diffusion was quantified with near-wall concentration measurements and the second experiment, which measured concentration profiles on a 0.94 m long flat-plate with three surface conditions: smooth, 240-grit, and 60-grit sandpaper. The increased diffusion does not fully explain the smooth-rough PDR differences observed in the first experiment. Rheological analysis of drawn samples from the first experiment indicates that polymer degradation (chain scission) could be responsible for the remaining loss of rough-wall PDR. These results have implications for the cost effectiveness of PDR for surface ships.

Near Wall measurement in Turbulent Flow over Rough Wall using microscopic HPIV

NASA Astrophysics Data System (ADS)

Talapatra, Siddharth; Hong, Jiarong; Katz, Joseph

2009-11-01

Using holographic PIV, 3D velocity measurements are being performed in a turbulent rough wall channel flow. Our objective is to examine the contribution of coherent structures to the flow dynamics, momentum and energy fluxes in the roughness sublayer. The 0.45mm high, pyramid-shaped roughness is uniformly distributed on the top and bottom surfaces of a 5X20cm rectangular channel flow, where the Reτ is 3400. To facilitate recording of holograms through a rough plate, the working fluid is a concentrated solution of NaI in water, whose optical refractive index is matched with that of the acrylic rough plates. The test section is illuminated by a collimated laser beam from the top, and the sample volume extends from the bottom wall up to 7 roughness heights. After passing through the sample volume, the in-line hologram is magnified and recorded on a 4864X3248 pixels camera at a resolution of 0.74μm/pixel. The flow is locally seeded with 2μm particles. Reconstruction, spatial filtering and particle tracking provide the 3D velocity field. This approach has been successfully implemented recently, as preliminary data demonstrate.

Development of 1D Particle-in-Cell Code and Simulation of Plasma-Wall Interactions

NASA Astrophysics Data System (ADS)

Rose, Laura P.

This thesis discusses the development of a 1D particle-in-cell (PIC) code and the analysis of plasma-wall interactions. The 1D code (Plasma and Wall Simulation -- PAWS) is a kinetic simulation of plasma done by treating both electrons and ions as particles. The goal of this thesis is to study near wall plasma interaction to better understand the mechanism that occurs in this region. The main focus of this investigation is the effects that secondary electrons have on the sheath profile. The 1D code is modeled using the PIC method. Treating both the electrons and ions as macroparticles the field is solved on each node and weighted to each macro particle. A pre-ionized plasma was loaded into the domain and the velocities of particles were sampled from the Maxwellian distribution. An important part of this code is the boundary conditions at the wall. If a particle hits the wall a secondary electron may be produced based on the incident energy. To study the sheath profile the simulations were run for various cases. Varying background neutral gas densities were run with the 2D code and compared to experimental values. Different wall materials were simulated to show their effects of SEE. In addition different SEE yields were run, including one study with very high SEE yields to show the presence of a space charge limited sheath. Wall roughness was also studied with the 1D code using random angles of incidence. In addition to the 1D code, an external 2D code was also used to investigate wall roughness without secondary electrons. The roughness profiles where created upon investigation of wall roughness inside Hall Thrusters based off of studies done on lifetime erosion of the inner and outer walls of these devices. The 2D code, Starfish[33], is a general 2D axisymmetric/Cartesian code for modeling a wide a range of plasma and rarefied gas problems. These results show that higher SEE yield produces a smaller sheath profile and that wall roughness produces a lower SEE yield. Modeling near wall interactions is not a simple or perfected task. Due to the lack of a second dimension and a sputtering model it is not possible with this study to show the positive effects wall roughness could have on Hall thruster performance since roughness occurs from the negative affect of sputtering.

Time Resolved Tomographic PIV Measurements of Rough-Wall Turbulent Channel Flow

NASA Astrophysics Data System (ADS)

Miorini, Rinaldo; Zhang, Cao; Katz, Joseph

2013-11-01

Time resolved tomographic PIV is used to study flow structures in the outer region of a rough-wall turbulent boundary layer, focusing on imprints of the roughness on the outer layer. Measurements are performed in a transparent channel installed in the JHU optically index matched facility. The roughness consists of pyramids with height, k = 0.46 mm, and wavelength, λ = 3.2 mm, satisfying h/k = 55 (h = 25.4 mm is the channel half-height), k + = 64 and Re = 40000. The TPIV setup consists of four high-speed cameras operating at 3 kHz, which view the sample volume through acrylic prisms. The flow field is illuminated by an Nd:YLF laser. Following enhancement, calibration, and reconstruction, 643 voxels interrogation volumes with 0.75 overlap provide 3D velocity fields with spacing of 0.5883 mm3. Formation and transport of near-wall 3D U-shaped vortex structures, with base in front of the pyramids, and quasi-streamwise legs extending between pyramid crest lines are evident from the data. Extended streamwise regions of high wall-normal vorticity appear ``latched'' to the roughness elements close to the wall, but are transported downstream at higher elevations. Also evident are traveling streamwise low velocity streaks, which cover many roughness elements. Sponsored by NSF CBET and ONR.

Urate is a ligand for the transcriptional regulator PecS.

PubMed

Perera, Inoka C; Grove, Anne

2010-09-24

PecS is a member of the MarR (multiple antibiotic resistance regulator) family, which has been shown in Erwinia to regulate the expression of virulence genes. MarR homologs typically bind a small molecule ligand, resulting in attenuated DNA binding. For PecS, the natural ligand has not been identified. We have previously shown that urate is a ligand for the Deinococcus radiodurans-encoded MarR homolog HucR (hypothetical uricase regulator) and identified residues responsible for ligand binding. We show here that all four residues involved in urate binding and propagation of conformational changes to DNA recognition helices are conserved in PecS homologs, suggesting that urate is the ligand for PecS. Consistent with this prediction, Agrobacterium tumefaciens PecS specifically binds urate, and urate attenuates DNA binding in vitro. PecS binds two operator sites in the intergenic region between the divergent pecS gene and pecM genes, one of which features two partially overlapping repeats to which PecS binds as a dimer on opposite faces of the duplex. Notably, urate dissociates PecS from cognate DNA, allowing transcription of both genes in vivo. Taken together, our data show that urate is a ligand for PecS and suggest that urate serves a novel function in signaling the colonization of a host plant. Copyright © 2010 Elsevier Ltd. All rights reserved.

Velocity distribution in a turbulent flow near a rough wall

NASA Astrophysics Data System (ADS)

Korsun, A. S.; Pisarevsky, M. I.; Fedoseev, V. N.; Kreps, M. V.

2017-11-01

Velocity distribution in the zone of developed wall turbulence, regardless of the conditions on the wall, is described by the well-known Prandtl logarithmic profile. In this distribution, the constant, that determines the value of the velocity, is determined by the nature of the interaction of the flow with the wall and depends on the viscosity of the fluid, the dynamic velocity, and the parameters of the wall roughness.In extreme cases depending on the ratio between the thickness of the viscous sublayer and the size of the roughness the constant takes on a value that does not depend on viscosity, or leads to a ratio for a smooth wall.It is essential that this logarithmic profile is the result not only of the Prandtl theory, but can be derived from general considerations of the theory of dimensions, and also follows from the condition of local equilibrium of generation and dissipation of turbulent energy in the wall area. This allows us to consider the profile as a universal law of velocity distribution in the wall area of a turbulent flow.The profile approximation up to the maximum speed line with subsequent integration makes possible to obtain the resistance law for channels of simple shape. For channels of complex shape with rough walls, the universal profile can be used to formulate the boundary condition when applied to the calculation of turbulence models.This paper presents an empirical model for determining the constant of the universal logarithmic profile. The zone of roughness is described by a set of parameters and is considered as a porous structure with variable porosity.

Screening effects in flow through rough channels.

PubMed

Andrade, J S; Araújo, A D; Filoche, M; Sapoval, B

2007-05-11

A surprising similarity is found between the distribution of hydrodynamic stress on the wall of an irregular channel and the distribution of flux from a purely Laplacian field on the same geometry. This finding is a direct outcome of numerical simulations of the Navier-Stokes equations for flow at low Reynolds numbers in two-dimensional channels with rough walls presenting either deterministic or random self-similar geometries. For high Reynolds numbers, the distribution of wall stresses on deterministic and random fractal rough channels becomes substantially dependent on the microscopic details of the walls geometry. Finally, the effects on the flow behavior of the channel symmetry and aspect ratio are also investigated.

Transcriptome analysis of the Dickeya dadantii PecS regulon during the early stages of interaction with Arabidopsis thaliana.

PubMed

Pédron, Jacques; Chapelle, Emilie; Alunni, Benoît; Van Gijsegem, Frédérique

2018-03-01

PecS is one of the major global regulators controlling the virulence of Dickeya dadantii, a broad-host-range phytopathogenic bacterium causing soft rot on several plant families. To define the PecS regulon during plant colonization, we analysed the global transcriptome profiles in wild-type and pecS mutant strains during the early colonization of the leaf surfaces and in leaf tissue just before the onset of symptoms, and found that the PecS regulon consists of more than 600 genes. About one-half of these genes are down-regulated in the pecS mutant; therefore, PecS has both positive and negative regulatory roles that may be direct or indirect. Indeed, PecS also controls the regulation of a few dozen regulatory genes, demonstrating that this global regulator is at or near the top of a major regulatory cascade governing adaptation to growth in planta. Notably, PecS acts mainly at the very beginning of infection, not only to prevent virulence gene induction, but also playing an active role in the adaptation of the bacterium to the epiphytic habitat. Comparison of the patterns of gene expression inside leaf tissues and during early colonization of leaf surfaces in the wild-type bacterium revealed 637 genes modulated between these two environments. More than 40% of these modulated genes are part of the PecS regulon, emphasizing the prominent role of PecS during plant colonization. © 2017 BSPP AND JOHN WILEY & SONS LTD.

pH-Dependent DNA Distortion and Repression of Gene Expression by Pectobacterium atrosepticum PecS.

PubMed

Deochand, Dinesh K; Meariman, Jacob K; Grove, Anne

2016-07-15

Transcriptional activity is exquisitely sensitive to changes in promoter DNA topology. Transcription factors may therefore control gene activity by modulating the relative positioning of -10 and -35 promoter elements. The plant pathogen Pectobacterium atrosepticum, which causes soft rot in potatoes, must alter gene expression patterns to ensure growth in planta. In the related soft-rot enterobacterium Dickeya dadantii, PecS functions as a master regulator of virulence gene expression. Here, we report that P. atrosepticum PecS controls gene activity by altering promoter DNA topology in response to pH. While PecS binds the pecS promoter with high affinity regardless of pH, it induces significant DNA distortion only at neutral pH, the pH at which the pecS promoter is repressed in vivo. At pH ∼8, DNA distortions are attenuated, and PecS no longer represses the pecS promoter. A specific histidine (H142) located in a crevice between the dimerization- and DNA-binding regions is required for pH-dependent changes in DNA distortion and repression of gene activity, and mutation of this histidine renders the mutant protein incapable of repressing the pecS promoter. We propose that protonated PecS induces a DNA conformation at neutral pH in which -10 and -35 promoter elements are suboptimally positioned for RNA polymerase binding; on deprotonation of PecS, binding is no longer associated with significant changes in DNA conformation, allowing gene expression. We suggest that this mode of gene regulation leads to differential expression of the PecS regulon in response to alkalinization of the plant apoplast.

On the influence of wall roughness in particle-laden flows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milici, Barbara; De Marchis, Mauro

2015-03-10

The distribution of inertial particles in turbulent flows is highly nonuniform and is governed by the local dynamics of the turbulent structures of the underlying carrier flow field. In wall-bounded flows, wall roughness strongly affects the turbulent flow field, nevertheless its effects on the particle transport in two-phase turbulent flows has been still poorly investigated. The issue is discussed here by addressing direct numerical simulations of a dilute dispersion of heavy particles in a turbulent channel flow, bounded by irregular two-dimensional rough surfaces, in the one-way coupling regime.

Definition of a consensus DNA-binding site for PecS, a global regulator of virulence gene expression in Erwinia chrysanthemi and identification of new members of the PecS regulon.

PubMed

Rouanet, Carine; Reverchon, Sylvie; Rodionov, Dmitry A; Nasser, William

2004-07-16

In Erwinia chrysanthemi, production of pectic enzymes is modulated by a complex network involving several regulators. One of them, PecS, which belongs to the MarR family, also controls the synthesis of various other virulence factors, such as cellulases and indigoidine. Here, the PecS consensus-binding site is defined by combining a systematic evolution of ligands by an exponential enrichment approach and mutational analyses. The consensus consists of a 23-base pair palindromic-like sequence (C(-11)G(-10)A(-9)N(-8)W(-7)T(-6)C(-5)G(-4)T(-3)A(-2))T(-1)A(0)T(1)(T(2)A(3)C(4)G(5)A(6)N(7)N(8)N(9)C(10)G(11)). Mutational experiments revealed that (i) the palindromic organization is required for the binding of PecS, (ii) the very conserved part of the consensus (-6 to 6) allows for a specific interaction with PecS, but the presence of the relatively degenerated bases located apart significantly increases PecS affinity, (iii) the four bases G, A, T, and C are required for efficient binding of PecS, and (iv) the presence of several binding sites on the same promoter increases the affinity of PecS. This consensus is detected in the regions involved in PecS binding on the previously characterized target genes. This variable consensus is in agreement with the observation that the members of the MarR family are able to bind various DNA targets as dimers by means of a winged helix DNA-binding motif. Binding of PecS on a promoter region containing the defined consensus results in a repression of gene transcription in vitro. Preliminary scanning of the E. chrysanthemi genome sequence with the consensus revealed the presence of strong PecS-binding sites in the intergenic region between fliE and fliFGHIJKLMNOPQR which encode proteins involved in the biogenesis of flagellum. Accordingly, PecS directly represses fliE expression. Thus, PecS seems to control the synthesis of virulence factors required for the key steps of plant infection.

Wall fluidization in two acts: from stiff to soft roughness.

PubMed

Derzsi, Ladislav; Filippi, Daniele; Lulli, Matteo; Mistura, Giampaolo; Bernaschi, Massimo; Garstecki, Piotr; Sbragaglia, Mauro; Pierno, Matteo

2018-02-14

Fluidization of soft glassy materials (SGMs) in microfluidic channels is affected by the wall roughness in the form of microtexturing. When SGMs flow across microgrooves, their constituents are likely trapped within the grooves' gap, and the way they are released locally modifies the fluidization close to the walls. By leveraging a suitable combination of experiments and numerical simulations on concentrated emulsions (a model SGM), we quantitatively report the existence of two physically different scenarios. When the gap is large compared to the droplets in the emulsion, the droplets hit the solid obstacles and easily escape scrambling with their neighbors. Conversely, as the gap spacing is reduced, droplets get trapped inside, creating a "soft roughness" layer, i.e. a complementary series of deformable posts from which overlying droplets are in turn released. In both cases, the induced fluidization scales with the grooves' density, although with a reduced prefactor for narrow gaps, accounting for the softness of the roughness. Both scenarios are also well distinguished via the statistics of the droplets displacement field close to the walls, with large deviations induced by the surface roughness, depending on its stiffness.

Microscopic Holography for flow over rough plate

NASA Astrophysics Data System (ADS)

Talapatra, Siddharth; Hong, Jiarong; Lu, Yuan; Katz, Joseph

2008-11-01

Our objective is to measure the near wall flow structures in a turbulent channel flow over a rough wall. In-line microscopic holographic PIV can resolve the 3-D flow field in a small sample volume, but recording holograms through a rough surface is a challenge. To solve this problem, we match the refractive indices of the fluid with that of the wall. Proof of concept tests involve an acrylic plate containing uniformly distributed, closely packed 0.45mm high pyramids with slope angle of 22^^o located within a concentrated sodium iodide solution. Holograms recorded by a 4864 x 3248 pixel digital camera at 10X magnification provide a field of view of 3.47mm x 2.32mm and pixel resolution of 0.714 μm. Due to index matching, reconstructed seed particles can be clearly seen over the entire volume, with only faint traces with the rough wall that can be removed. Planned experiments will be performed in a 20 x 5 cm rectangular channel with the top and bottom plates having the same roughness as the sample plate.

An integral wall model for Large Eddy Simulation (iWMLES) and applications to developing boundary layers over smooth and rough plates

NASA Astrophysics Data System (ADS)

Yang, Xiang; Sadique, Jasim; Mittal, Rajat; Meneveau, Charles

2014-11-01

A new wall model for Large-Eddy-Simulations is proposed. It is based on an integral boundary layer method that assumes a functional form for the local mean velocity profile. The method, iWMLES, evaluates required unsteady and advective terms in the vertically integrated boundary layer equations analytically. The assumed profile contains a viscous or roughness sublayer, and a logarithmic layer with an additional linear term accounting for inertial and pressure gradient effects. The iWMLES method is tested in the context of a finite difference LES code. Test cases include developing turbulent boundary layers on a smooth flat plate at various Reynolds numbers, over flat plates with unresolved roughness, and a sample application to boundary layer flow over a plate that includes resolved roughness elements. The elements are truncated cones acting as idealized barnacle-like roughness elements that often occur in biofouling of marine surfaces. Comparisons with data show that iWMLES provides accurate predictions of near-wall velocity profiles in LES while, similarly to equilibrium wall models, its cost remains independent of Reynolds number and is thus significantly lower compared to standard zonal or hybrid wall models. This work is funded by ONR Grant N00014-12-1-0582 (Dr. R. Joslin, program manager).

Efficacy of pectoral nerve block versus thoracic paravertebral block for postoperative analgesia after radical mastectomy: a randomized controlled trial.

PubMed

Kulhari, S; Bharti, N; Bala, I; Arora, S; Singh, G

2016-09-01

Pectoral nerve (PecS) block is a recently introduced technique for providing surgical anaesthesia and postoperative analgesia during breast surgery. The present study was planned to compare the efficacy and safety of ultrasound-guided PecS II block with thoracic paravertebral block (TPVB) for postoperative analgesia after modified radical mastectomy. Forty adult female patients undergoing radical mastectomy were randomly allocated into two groups. Group 1 patients received a TPVB with ropivacaine 0.5%, 25 ml, whereas Group 2 patents received a PecS II block using same volume of ropivacaine 0.5% before induction of anaesthesia. Patient-controlled morphine analgesia was used for postoperative pain relief. The duration of analgesia was significantly prolonged in patients receiving the PecS II block compared with TPVB [mean (sd), 294.5 (52.76) vs 197.5 (31.35) min in the PecS II and TPVB group, respectively; P<0.0001]. The 24 h morphine consumption was also less in the PecS II block group [mean (sd), 3.90 (0.79) vs 5.30 (0.98) mg in PecS II and TPVB group, respectively; P<0.0001]. Postoperative pain scores were lower in the PecS II group compared with the TVPB group in the initial 2 h after surgery [median (IQR), 2 (2-2.5) vs 4 (3-4) in the Pecs II and TPVB group, respectively; P<0.0001]. Seventeen patients in the PecS II block group had T2 dermatomal spread compared with four patients in the TPVB group (P<0.001). No block-related complication was recorded. We found that the PecS II block provided superior postoperative analgesia than the TPVB in patients undergoing modified radical mastectomy without causing any adverse effect. CTRI/2014/06/004692. © The Author 2016. Published by Oxford University Press on behalf of the British Journal of Anaesthesia. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Pore-wall roughness as a fractal surface and theoretical simulation of mercury intrusion/retraction in porous media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsakiroglou, C.D.; Payatakes, A.C.

The mercury intrusion/retraction curves of many types of porous materials (e.g., sandstones) have sections of finite slope in the region of high and very high pressure. This feature is attributed to the existence of microroughness on the pore walls. In the present work pore-wall roughness features are added to a three-dimensional primary network of chambers-and-throats using ideas of fractal geometry. The roughness of the throats is modeled with a finite number of self-similar triangular prisms of progressively smaller sizes. The roughness of the chambers is modeled in a similar way using right circular cones instead of prisms. Three parameters sufficemore » for the complete characterization of the model of fractal roughness, namely, the number of features per unit length, the common angle of sharpness, and the number of layers (which is taken to be the same for throats and chambers). Analytical relations that give the surface area, pore volume, and mercury saturation of the pore network as functions of the fractal roughness parameters are developed for monolayer and multilayer arrangements. The chamber-and-throat network with fractal pore-wall roughness is used to develop an extended version of the computer-aided simulator of mercury porosimetry that has been reported in previous publications. This new simulator is used to investigate the effects of the roughness features on the form of mercury intrusion/retraction curves. It turns out that the fractal model of the porewall roughness gives an adequate representation of real porous media, and capillary pressure curves which are similar to the experimental ones for many typical porous materials such as sandstones. The method is demonstrated with the analysis of a Greek sandstone.« less

Influence of wall roughness and thermal coductivity on turbulent natural convection

NASA Astrophysics Data System (ADS)

Orlandi, Paolo; Pirozzoli, Sergio; Bernardini, Matteo

2015-11-01

We study turbulent natural convection in enclosures with conjugate heat transfer. The simplest way to increase the heat transfer in this flow is through rough surfaces. In numerical simulations often constant temperatures are assigned on the walls, but this is an unrealistic condition in laboratory experiments. Therefore, in the DNS, to be of help to experimentalists, it is necessary to solve the heat conduction in the solid walls together with the turbulent flow between the hot and the cold walls. Here the cold wall, 0 . 5 h tick is smooth, and the hot wall has 2D and 3D rough elements of thickness 0 . 2 h above a solid layer 0 . 3 h tick. The simulation is performed in a bi-periodic domain 4 h wide. The Rayleigh number varies from 106 to 108. Two values of the thermal conductivity, one corresponding to copper and the other ten times higher were assumed. It has been found that the Nusselt number behaves as Nu = αRaγ , with α increasing with the solid conductivity and depending of the roughness shape. 3D elements produce a heat transfer greater than 2D elements. An imprinting of the flow structures on the thermal field inside the walls is observed. The one-dimensional spectra at the center, one decade wide, agree with those of forced isotropic turbulence.

Analysis of the coherent and turbulent stresses of a numerically simulated rough wall pipe

NASA Astrophysics Data System (ADS)

Chan, L.; MacDonald, M.; Chung, D.; Hutchins, N.; Ooi, A.

2017-04-01

A turbulent rough wall flow in a pipe is simulated using direct numerical simulation (DNS) where the roughness elements consist of explicitly gridded three-dimensional sinusoids. Two groups of simulations were conducted where the roughness semi-amplitude h+ and the roughness wavelength λ+ are systematically varied. The triple decomposition is applied to the velocity to separate the coherent and turbulent components. The coherent or dispersive component arises due to the roughness and depends on the topological features of the surface. The turbulent stress on the other hand, scales with the friction Reynolds number. For the case with the largest roughness wavelength, large secondary flows are observed which are similar to that of duct flows. The occurrence of these large secondary flows is due to the spanwise heterogeneity of the roughness which has a spacing approximately equal to the boundary layer thickness δ.

Wall roughness effect on gas dynamics in supersonic ejector

NASA Astrophysics Data System (ADS)

Aronson, K. E.; Brezgin, D. V.

2016-10-01

The paper presents the numerical simulations results in order to figure out the influence of the wall surface roughness on gas-dynamic processes inside the supersonic ejector. For these purposes two commercial CFD-solvers (Star-CCM+ and Fluent) were used. A detailed comparative study of the built-in tools and approaches in both CFD-packages for evaluation of surface roughness effects on the logarithmic law velocity distribution inside the boundary layer is carried out. Influence of ejector surface roughness is compared with the influence of the backpressure. It is found out that either increasing the backpressure behind the ejector or increasing the surface roughness height, the appearance section of a pressure shock is displaced upstream (closer to the primary nozzle). The numerical simulations results of the ejector with rough walls in both CFD-solvers are well quantitative agreed between each other in terms of the mass flow rates and are well qualitative consistent in terms of the local flow parameters distribution. It is found out that in case of exceeding the "critical roughness height" for the given geometry and boundary conditions, the ejector switches to the "off-design" mode and its performance is significantly reduced.

Detection of longitudinal ulcer using roughness value for computer aided diagnosis of Crohn's disease

NASA Astrophysics Data System (ADS)

Oda, Masahiro; Kitasaka, Takayuki; Furukawa, Kazuhiro; Watanabe, Osamu; Ando, Takafumi; Goto, Hidemi; Mori, Kensaku

2011-03-01

The purpose of this paper is to present a new method to detect ulcers, which is one of the symptoms of Crohn's disease, from CT images. Crohn's disease is an inflammatory disease of the digestive tract. Crohn's disease commonly affects the small intestine. An optical or a capsule endoscope is used for small intestine examinations. However, these endoscopes cannot pass through intestinal stenosis parts in some cases. A CT image based diagnosis allows a physician to observe whole intestine even if intestinal stenosis exists. However, because of the complicated shape of the small and large intestines, understanding of shapes of the intestines and lesion positions are difficult in the CT image based diagnosis. Computer-aided diagnosis system for Crohn's disease having automated lesion detection is required for efficient diagnosis. We propose an automated method to detect ulcers from CT images. Longitudinal ulcers make rough surface of the small and large intestinal wall. The rough surface consists of combination of convex and concave parts on the intestinal wall. We detect convex and concave parts on the intestinal wall by a blob and an inverse-blob structure enhancement filters. A lot of convex and concave parts concentrate on roughed parts. We introduce a roughness value to differentiate convex and concave parts concentrated on the roughed parts from the other on the intestinal wall. The roughness value effectively reduces false positives of ulcer detection. Experimental results showed that the proposed method can detect convex and concave parts on the ulcers.

Automated Geometry assisted PEC for electron beam direct write nanolithography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ocola, Leonidas E.; Gosztola, David J.; Rosenmann, Daniel

Nanoscale geometry assisted proximity effect correction (NanoPEC) is demonstrated to improve PEC for nanoscale structures over standard PEC, in terms of feature sharpness for sub-100 nm structures. The method was implemented onto an existing commercially available PEC software. Plasmonic arrays of crosses were fabricated using regular PEC and NanoPEC, and optical absorbance was measured. Results confirm that the improved sharpness of the structures leads to increased sharpness in the optical absorbance spectrum features. We also demonstrated that this method of PEC is applicable to arbitrary shaped structures beyond crosses.

Dynamics of viscous drops confined in a rough medium

NASA Astrophysics Data System (ADS)

Keiser, Ludovic; Gas, Armelle; Jaafar, Khalil; Bico, Jose; Reyssat, Etienne

2017-11-01

We focus on the dynamics of viscous and non-wetting ``pancake'' droplets of oil conned in a vertical Hele-Shaw cell filled with a less viscous surfactant solution. These dense drops settle at constant velocity driven by gravity. The surfactant solution completely wets the walls, and a thin lubrication film separates the drops from the walls. With smooth walls, two main dynamical regimes are characterized as the gap between the walls is varied. Viscous dissipation is found to dominate either in the droplet or in the lubrication film, depending on the ratio of viscosities and length scales. A sharp transition between both regimes is observed and successfully captured by asymptotic models. With rough walls, that transition is dramatically altered. Drops are generally much slower in a rough Hele-Shaw cell, in comparison with a similar smooth cell. Building up on the seminal works of Seiwert et al. (J.F.M. 2011) on film deposition by dip coating on a rough surface, we shed light on the non-trivial friction processes resulting from the interplay of viscous dissipation at the front of the drop, in the lubrication film and in the bulk of the drop. We acknowledge funding from Total S.A.

High Reynolds number rough wall turbulent boundary layer experiments using Braille surfaces

NASA Astrophysics Data System (ADS)

Harris, Michael; Monty, Jason; Nova, Todd; Allen, James; Chong, Min

2007-11-01

This paper details smooth, transitional and fully rough turbulent boundary layer experiments in the New Mexico State high Reynolds number rough wall wind tunnel. The initial surface tested was generated with a Braille printer and consisted of an uniform array of Braille points. The average point height being 0.5mm, the spacing between the points in the span was 0.5mm and the surface consisted of span wise rows separated by 4mm. The wavelength to peak ratio was 8:1. The boundary layer thickness at the measurement location was 190mm giving a large separation of roughness height to layer thickness. The maximum friction velocity was uτ=1.5m/s at Rex=3.8 x10^7. Results for the skin friction co-efficient show that this surface follows a Nikuradse type inflectional curve and that Townsends outer layer similarity hypothesis is valid for rough wall flows with a large separation of scales. Mean flow and turbulence statistics will be presented.

A Study of the Mean Force Structure of Rough-Wall Turbulent Boundary Layers

NASA Astrophysics Data System (ADS)

Mehdi, Faraz; Klewicki, Joseph

2011-11-01

Analysis of existing data by Mehdi, Klewicki & White [Physica D 239(2010)] provides evidence that the traditional classifications do not fully account for the combined effects of roughness and Reynolds number. We continue to explore this further, and in the present talk report on experiments that used 24-grit sandpaper and pea gravel for roughness over an 8m fetch. Two-component LDV measurements are used to acquire well-resolved mean velocity and Reynolds stress profiles over a modest range of Reynolds numbers. These data are used to estimate the terms in the appropriate mean statement of dynamics, which directly reveals the operative time-averaged balance of forces. The present results further reinforce the previous observation that the mean viscous force retains dominant order above (and often well-above) the roughness elements. Force balance data are shown to be usefully organized relative to the length scale that defines the region from the wall to where the leading order mean dynamics are described by a balance between mean advection and the mean effect of turbulent inertia. In the smooth-wall flow, this length scale is only a function of Reynolds number. In rough-wall flows, the data indicate it to be a function of roughness and Reynolds number. The support of the ONR (N000140810836, grant monitor Ronald Joslin) is gratefully acknowledged.

Breakthroughs in Low-Profile Leaky-Wave HPM Antennas

DTIC Science & Technology

2015-12-21

sqrt(a^2-z1(n)^2); % drivative value, f’(z1(n)) w11 = atan(-fpz1); w1(n) = w11; % slope angle is stored to testing ...compensation. 3.5. Design approximation for the lower (PEC) wall of the LWA In this section we attempt to develop and test an algorithm for...Three different alternatives were tested : A function created by interpolating a polynomial that passes through all the computed points seemed to be a

Percutaneous endoscopic colostomy: a useful technique when surgery is not an option.

PubMed

Tun, Gloria; Bullas, Dominic; Bannaga, Ayman; Said, Elmuhtady M

2016-01-01

Percutaneous endoscopic colostomy (PEC) is a minimally invasive endoscopic procedure that offers an alternative treatment for high-risk patients with sigmoid volvulus or intestinal pseudo-obstruction who have tried conventional treatment options without success or those who are unfit for surgery. The procedure acts as an irrigation or decompressing channel and provides colonic 'fixation' to the anterior abdominal wall. The risk of complications highlights the importance of informed consent for patients and relatives.

Percutaneous endoscopic colostomy for adults with chronic constipation: Retrospective case series of 12 patients.

PubMed

Strijbos, D; Keszthelyi, D; Masclee, A A M; Gilissen, L P L

2018-05-01

Percutaneous endoscopic colostomy (PEC) is a technique derived from percutaneous endoscopic gastrostomy. When conservative treatment of chronic obstipation fails, colon irrigation via PEC seems less invasive than surgical interventions. However, previous studies have noted high complication rates of PEC, mostly related to infections. Our aim was to report our experiences with PEC in patients with chronic refractory constipation. Retrospective analysis of all patients who underwent PEC for refractory constipation in our secondary referral hospital between 2009 and 2016. Twelve patients received a PEC for chronic, refractory constipation. Short-term efficacy for relief of constipation symptoms was good in 8 patients and moderate in 4 patients. Two patients had the PEC removed because of spontaneous improvement of constipation. Three patients, who initially noticed a positive effect, preferred an ileostomy over PEC after 1-5 years. One PEC was removed because of an abscess. Long-term efficacy is 50%: 6 patients still use their PEC after 3.3 years of follow-up. No mortality occurred. PEC offers a technically easily feasible and safe treatment option for patients with chronic constipation not responding to conventional therapy. Long-term efficacy of PEC in our patients is 50%. © 2017 John Wiley & Sons Ltd.

Surgical excision of the breast giant fibroadenoma under regional anesthesia by Pecs II and internal intercostal plane block: a case report and brief technical description: a case report.

PubMed

Kim, Hyungtae; Shim, Junho; Kim, Ikthae

2017-02-01

A 22-years-old female patient at 171 cm and 67 kg visited the Department of Breast Surgery of the hospital with a mass accompanied with pain on the left side breast as chief complaints. Since physical examination revealed a suspected huge mass, breast surgeon decided to perform surgical excision and requested anesthesia to our department. Surgery of breast tumor is often under local anesthesia. However, in case of big size tumor, surgery is usually performed under general anesthesia. The patient feared general anesthesia. Unlike abdominal surgery, there is no need to control visceral pain for breast and anterior thoracic wall surgery. Therefore, we decided to perform resection under regional anesthesia. Herein, we report a successful anesthetic and pain management of the patient undergoing excision of a huge breast fibroadenoma under regional anesthesia using Pecs II and internal intercostal plane block.

Diffusion of drag-reducing polymer solutions within a rough-walled turbulent boundary layer

NASA Astrophysics Data System (ADS)

Elbing, Brian R.; Dowling, David R.; Perlin, Marc; Ceccio, Steven L.

2010-04-01

The influence of surface roughness on diffusion of wall-injected, drag-reducing polymer solutions within a turbulent boundary layer was studied with a 0.94 m long flat-plate test model at speeds of up to 10.6 m s-1 and Reynolds numbers of up to 9×106. The surface was hydraulically smooth, transitionally rough, or fully rough. Mean concentration profiles were acquired with planar laser induced fluorescence, which was the primary flow diagnostic. Polymer concentration profiles with high injection concentrations (≥1000 wppm) had the peak concentration shifted away from the wall, which was partially attributed to a lifting phenomenon. The diffusion process was divided into three zones—initial, intermediate, and final. Studies of polymer injection into a polymer ocean at concentrations sufficient for maximum drag reduction indicated that the maximum initial zone length is of the order of 100 boundary layer thicknesses. The intermediate zone results indicate that friction velocity and roughness height are important scaling parameters in addition to flow and injection conditions. Lastly, the current results were combined with those in Petrie et al. ["Polymer drag reduction with surface roughness in flat-plate turbulent boundary layer flow," Exp. Fluids 35, 8 (2003)] to demonstrate that the influence of polymer degradation increases with increased surface roughness.

Modification of the large-scale features of high Reynolds number wall turbulence by passive surface obtrusions

NASA Astrophysics Data System (ADS)

Monty, J. P.; Allen, J. J.; Lien, K.; Chong, M. S.

2011-12-01

A high Reynolds number boundary-layer wind-tunnel facility at New Mexico State University was fitted with a regularly distributed braille surface. The surface was such that braille dots were closely packed in the streamwise direction and sparsely spaced in the spanwise direction. This novel surface had an unexpected influence on the flow: the energy of the very large-scale features of wall turbulence (approximately six-times the boundary-layer thickness in length) became significantly attenuated, even into the logarithmic region. To the author's knowledge, this is the first experimental study to report a modification of `superstructures' in a rough-wall turbulent boundary layer. The result gives rise to the possibility that flow control through very small, passive surface roughness may be possible at high Reynolds numbers, without the prohibitive drag penalty anticipated heretofore. Evidence was also found for the uninhibited existence of the near-wall cycle, well known to smooth-wall-turbulence researchers, in the spanwise space between roughness elements.

Effects of roughness height, pressure and streamwise distance on stress profiles in the inner part of turbulent boundary layer over super-hydrophobic surfaces

NASA Astrophysics Data System (ADS)

Ling, Hangjian; Katz, Joseph; Srinivasan, Siddarth; McKinley, Gareth; Golovin, Kevin; Tuteja, Anish; Pillutla, Venkata; Abhijeet, Abhijeet; Choi, Wonjae

2016-11-01

Digital holographic microscopy is used for measuring the mean velocity and stress in the inner part of turbulent boundary layers over sprayed or etched super-hydrophobic surfaces (SHSs). The slip velocity and wall friction are calculated directly from the mean velocity and its gradient along with the Reynolds shear stress at the top of SHSs "roughness". Effects of the normalized rms roughness height krms+, facility pressure p and streamwise distance x from the beginning of SHSs on mean flow are examined. For krms+<1 and pkrms / σ <1 (σ is surface tension), the SHSs show 10-28% wall friction reduction, 15-30% slip velocity and λ+ = 3-10 slip length. Increasing Reynolds number and/or krms to establish krms+>1, and increasing p to achieve pkrms / σ >1 suppress the drag reduction, as roughness effects and associated near wall Reynolds stress increase. When the roughness effect is not dominant, the measurements agree with previous theoretical predictions of the relationships between drag reduction and slip velocity. The significance of spanwise slip relative to streamwise slip varies with the SHSs texture. Transitions from a smooth wall to a SHS involve overshoot of Reynolds stress and undershoot of viscous stress, trends that diminish with x. Sponsored by ONR.

The Role of Law-of-the-Wall and Roughness Scale in the Surface Stress Model for LES of the Rough-wall Boundary Layer

NASA Astrophysics Data System (ADS)

Brasseur, James; Paes, Paulo; Chamecki, Marcelo

2017-11-01

Large-eddy simulation (LES) of the high Reynolds number rough-wall boundary layer requires both a subfilter-scale model for the unresolved inertial term and a ``surface stress model'' (SSM) for space-time local surface momentum flux. Standard SSMs assume proportionality between the local surface shear stress vector and the local resolved-scale velocity vector at the first grid level. Because the proportionality coefficient incorporates a surface roughness scale z0 within a functional form taken from law-of-the-wall (LOTW), it is commonly stated that LOTW is ``assumed,'' and therefore ``forced'' on the LES. We show that this is not the case; the LOTW form is the ``drag law'' used to relate friction velocity to mean resolved velocity at the first grid level consistent with z0 as the height where mean velocity vanishes. Whereas standard SSMs do not force LOTW on the prediction, we show that parameterized roughness does not match ``true'' z0 when LOTW is not predicted, or does not exist. By extrapolating mean velocity, we show a serious mismatch between true z0 and parameterized z0 in the presence of a spurious ``overshoot'' in normalized mean velocity gradient. We shall discuss the source of the problem and its potential resolution.

Structure of turbulent flow over regular arrays of cubical roughness

NASA Astrophysics Data System (ADS)

Coceal, O.; Dobre, A.; Thomas, T. G.; Belcher, S. E.

The structure of turbulent flow over large roughness consisting of regular arrays of cubical obstacles is investigated numerically under constant pressure gradient conditions. Results are analysed in terms of first- and second-order statistics, by visualization of instantaneous flow fields and by conditional averaging. The accuracy of the simulations is established by detailed comparisons of first- and second-order statistics with wind-tunnel measurements. Coherent structures in the log region are investigated. Structure angles are computed from two-point correlations, and quadrant analysis is performed to determine the relative importance of Q2 and Q4 events (ejections and sweeps) as a function of height above the roughness. Flow visualization shows the existence of low-momentum regions (LMRs) as well as vortical structures throughout the log layer. Filtering techniques are used to reveal instantaneous examples of the association of the vortices with the LMRs, and linear stochastic estimation and conditional averaging are employed to deduce their statistical properties. The conditional averaging results reveal the presence of LMRs and regions of Q2 and Q4 events that appear to be associated with hairpin-like vortices, but a quantitative correspondence between the sizes of the vortices and those of the LMRs is difficult to establish; a simple estimate of the ratio of the vortex width to the LMR width gives a value that is several times larger than the corresponding ratio over smooth walls. The shape and inclination of the vortices and their spatial organization are compared to recent findings over smooth walls. Characteristic length scales are shown to scale linearly with height in the log region. Whilst there are striking qualitative similarities with smooth walls, there are also important differences in detail regarding: (i) structure angles and sizes and their dependence on distance from the rough surface; (ii) the flow structure close to the roughness; (iii) the roles of inflows into and outflows from cavities within the roughness; (iv) larger vortices on the rough wall compared to the smooth wall; (v) the effect of the different generation mechanism at the wall in setting the scales of structures.

Direct Numerical Simulation of Flow Over Passive Geometric Disturbances

NASA Astrophysics Data System (ADS)

Vizard, Alexander

It is well understood that delaying flow separation on a bluff body allows significant drag reduction, which is attractive in many applications. With this in mind, many separation control mechanisms, both active and passive, have been developed and tested to optimize the effects of this phenomenon. Although this idea is generally accepted, the physical occurrences in the near-wall region during transition that lead to separation delay are not well understood. The current study evaluates the impact of both spherical dimples, and sandgrain style roughness on downstream flow by performing direct numerical simulations over such geometries on a zero pressure gradient flat plate. It is shown that although dimples and random roughness of similar characteristic length scales exhibit similar boundary layer characteristics, dimples are more successful in developing high momentum in the vicinity of the wall. Additionally it is shown that increasing the relative size of the rough elements does not increase the near-wall momentum, and is undesirable in controlling separation. Finally, it is shown that the impact of roughness elements on the flow is more immediate, and that, for the case of one row of dimples and an equivalent area of roughness, the roughness patch is more successful in transitioning the near-wall region to a non-laminar state. It can be concluded from variation in the span of the flowfield for a single row of dimples that the size and orientation of the disturbance region is significant to the results.

Evaluation of Escherichia coli isolates from healthy chickens to determine their potential risk to poultry and human health.

PubMed

Stromberg, Zachary R; Johnson, James R; Fairbrother, John M; Kilbourne, Jacquelyn; Van Goor, Angelica; Curtiss, Roy; Mellata, Melha

2017-01-01

Extraintestinal pathogenic Escherichia coli (ExPEC) strains are important pathogens that cause diverse diseases in humans and poultry. Some E. coli isolates from chicken feces contain ExPEC-associated virulence genes, so appear potentially pathogenic; they conceivably could be transmitted to humans through handling and/or consumption of contaminated meat. However, the actual extraintestinal virulence potential of chicken-source fecal E. coli is poorly understood. Here, we assessed whether fecal E. coli isolates from healthy production chickens could cause diseases in a chicken model of avian colibacillosis and three rodent models of ExPEC-associated human infections. From 304 E. coli isolates from chicken fecal samples, 175 E. coli isolates were screened by PCR for virulence genes associated with human-source ExPEC or avian pathogenic E. coli (APEC), an ExPEC subset that causes extraintestinal infections in poultry. Selected isolates genetically identified as ExPEC and non-ExPEC isolates were assessed in vitro for virulence-associated phenotypes, and in vivo for disease-causing ability in animal models of colibacillosis, sepsis, meningitis, and urinary tract infection. Among the study isolates, 13% (40/304) were identified as ExPEC; the majority of these were classified as APEC and uropathogenic E. coli, but none as neonatal meningitis E. coli. Multiple chicken-source fecal ExPEC isolates resembled avian and human clinical ExPEC isolates in causing one or more ExPEC-associated illnesses in experimental animal infection models. Additionally, some isolates that were classified as non-ExPEC were able to cause ExPEC-associated illnesses in animal models, and thus future studies are needed to elucidate their mechanisms of virulence. These findings show that E. coli isolates from chicken feces contain ExPEC-associated genes, exhibit ExPEC-associated in vitro phenotypes, and can cause ExPEC-associated infections in animal models, and thus may pose a health threat to poultry and consumers.

Evaluation of Escherichia coli isolates from healthy chickens to determine their potential risk to poultry and human health

PubMed Central

Johnson, James R.; Fairbrother, John M.; Kilbourne, Jacquelyn; Van Goor, Angelica; Curtiss, Roy; Mellata, Melha

2017-01-01

Extraintestinal pathogenic Escherichia coli (ExPEC) strains are important pathogens that cause diverse diseases in humans and poultry. Some E. coli isolates from chicken feces contain ExPEC-associated virulence genes, so appear potentially pathogenic; they conceivably could be transmitted to humans through handling and/or consumption of contaminated meat. However, the actual extraintestinal virulence potential of chicken-source fecal E. coli is poorly understood. Here, we assessed whether fecal E. coli isolates from healthy production chickens could cause diseases in a chicken model of avian colibacillosis and three rodent models of ExPEC-associated human infections. From 304 E. coli isolates from chicken fecal samples, 175 E. coli isolates were screened by PCR for virulence genes associated with human-source ExPEC or avian pathogenic E. coli (APEC), an ExPEC subset that causes extraintestinal infections in poultry. Selected isolates genetically identified as ExPEC and non-ExPEC isolates were assessed in vitro for virulence-associated phenotypes, and in vivo for disease-causing ability in animal models of colibacillosis, sepsis, meningitis, and urinary tract infection. Among the study isolates, 13% (40/304) were identified as ExPEC; the majority of these were classified as APEC and uropathogenic E. coli, but none as neonatal meningitis E. coli. Multiple chicken-source fecal ExPEC isolates resembled avian and human clinical ExPEC isolates in causing one or more ExPEC-associated illnesses in experimental animal infection models. Additionally, some isolates that were classified as non-ExPEC were able to cause ExPEC-associated illnesses in animal models, and thus future studies are needed to elucidate their mechanisms of virulence. These findings show that E. coli isolates from chicken feces contain ExPEC-associated genes, exhibit ExPEC-associated in vitro phenotypes, and can cause ExPEC-associated infections in animal models, and thus may pose a health threat to poultry and consumers. PMID:28671990

An Experimental Study of Momentum and Thermal Transport in Flow through Smooth- and Rough-Wall Microchannels

ERIC Educational Resources Information Center

Natrajan, Vinay Kumar

2009-01-01

The impact of surface roughness on momentum and thermal transport in microscale flow passages of hydraulic diameter D[subscript h] = 600 micrometer is investigated in the laminar, transitional and turbulent flow regimes using microscopic PIV, two-color LIF thermometry and pressure-drop measurements. In addition to smooth-wall flow, two different…

PecS and PecT coregulate the synthesis of HrpN and pectate lyases, two virulence determinants in Erwinia chrysanthemi 3937.

PubMed

Nasser, William; Reverchon, Sylvie; Vedel, Regine; Boccara, Martine

2005-11-01

Erwinia chrysanthemi strain 3937 is a necrotrophic bacterial plant pathogen. Pectinolytic enzymes and, in particular, pectate lyases play a key role in soft rot symptoms; however, the efficient colonization of plants by E. chrysanthemi requires additional factors. These factors include HrpN (harpin), a heat-stable, glycine-rich hydrophilic protein, which is secreted by the type III secretion system. We investigated the expression of hrpN in E. chrysanthemi 3937 in various environmental conditions and different regulatory backgrounds. Using lacZ fusions, hrpN expression was markedly influenced by the carbon source, osmolarity, growth phase, and growth substrate. hrpN was repressed when pectinolysis started and negatively regulated by the repressors of pectate lyase synthesis, PecS and PecT. Primer extension data and in vitro DNA-protein interaction experiments support a model whereby PecS represses hrpN expression by binding to the hrpN regulatory region and inhibiting transcript elongation. The results suggest coordinated regulation of HrpN and pectate lyases by PecS and PecT. A putative model of the synthesis of these two virulence factors in E. chrysanthemi during pathogenesis is presented.

Percutaneous endoscopic colostomy: a useful technique when surgery is not an option

PubMed Central

Tun, Gloria; Bullas, Dominic; Bannaga, Ayman; Said, Elmuhtady M.

2016-01-01

Percutaneous endoscopic colostomy (PEC) is a minimally invasive endoscopic procedure that offers an alternative treatment for high-risk patients with sigmoid volvulus or intestinal pseudo-obstruction who have tried conventional treatment options without success or those who are unfit for surgery. The procedure acts as an irrigation or decompressing channel and provides colonic ‘fixation’ to the anterior abdominal wall. The risk of complications highlights the importance of informed consent for patients and relatives. PMID:27708513

Study of a Waveguide Antenna Implemented in Laminated Material

DTIC Science & Technology

2002-12-01

CRC had some experience with fabricating microwave circuits with laminated copper clad dielectric. There was bonding material (CLTE-P) that could be...PEC) and copper walls in Table 4. For all of the simulations, the physical parameters (width= 5.13 mm, height=3.40 mm, length=24.27 mm) and the... copper waveguide. As shown in Chapter 2, it is also possible to determine the losses from the conductor and dielectric (Equations 2.6 - 2.8) of a RWG

Experimental and Theoretical Studies of the Pure Rotational Spectra of Lead Halides: PbF and PbCl

NASA Astrophysics Data System (ADS)

Norman, Spencer; Dawes, Richard; Grubbs, G. S., II; Cooke, S. A.; Long, B. E.; Dewberry, Chris

2014-06-01

The pure rotational spectrum of lead monochloride, PbCl, has been measured and analyzed using chirped pulse and cavity Fourier transform microwave (CP-FTMW and FTMW) spectrometers equipped with an ablation source. Refined parameters of an effective Hamiltonian including fine and hyperfine interactions similar to those previously reported by Fink et al. [1] were determined. Dynamically-weighted, explicitly-correlated MRCI-F12 calculations [2] were performed for both PbF and the valence isoelectronic PbCl to predict potential energy curves (PEC). Spin-orbit coupling was included in the calculations, which is known to split the X12Π1/2 and X22Π3/2 components of the ground electronic state by roughly 8280 wn in both lead halide systems. Calculated rotational levels were obtained using the PECs and compared with experiment including previously published results for PbF [3]. References: 1- K. Ziebarth, K. D. Setzer, O. Shestakov,1 and E. H. Fink, J. Mol. Spec. 191, 108 (1998). 2- B. J. Barker et al. J. Chem. Phys. 137, 214313 (2012). 3- R. J. Mawhorter et al. Phys. Rev. A 84, 022508 (2011).

An intermittency model for predicting roughness induced transition

NASA Astrophysics Data System (ADS)

Ge, Xuan; Durbin, Paul

2014-11-01

An extended model for roughness-induced transition is proposed based on an intermittency transport equation for RANS modeling formulated in local variables. To predict roughness effects in the fully turbulent boundary layer, published boundary conditions for k and ω are used, which depend on the equivalent sand grain roughness height, and account for the effective displacement of wall distance origin. Similarly in our approach, wall distance in the transition model for smooth surfaces is modified by an effective origin, which depends on roughness. Flat plate test cases are computed to show that the proposed model is able to predict the transition onset in agreement with a data correlation of transition location versus roughness height, Reynolds number, and inlet turbulence intensity. Experimental data for a turbine cascade are compared with the predicted results to validate the applicability of the proposed model. Supported by NSF Award Number 1228195.

Integrated photoelectrochemical cell and system having a liquid electrolyte

DOEpatents

Deng, Xunming; Xu, Liwei

2010-07-06

An integrated photoelectrochemical (PEC) cell generates hydrogen and oxygen from water while being illuminated with radiation. The PEC cell employs a liquid electrolyte, a multi-junction photovoltaic electrode, and a thin ion-exchange membrane. A PEC system and a method of making such PEC cell and PEC system are also disclosed.

Enhanced Photoelectrochemical Behavior of H-TiO2 Nanorods Hydrogenated by Controlled and Local Rapid Thermal Annealing

NASA Astrophysics Data System (ADS)

Wang, Xiaodan; Estradé, Sonia; Lin, Yuanjing; Yu, Feng; Lopez-Conesa, Lluis; Zhou, Hao; Gurram, Sanjeev Kumar; Peiró, Francesca; Fan, Zhiyong; Shen, Hao; Schaefer, Lothar; Braeuer, Guenter; Waag, Andreas

2017-05-01

Recently, colored H-doped TiO2 (H-TiO2) has demonstrated enhanced photoelectrochemical (PEC) performance due to its unique crystalline core—disordered shell nanostructures and consequent enhanced conduction behaviors between the core-shell homo-interfaces. Although various hydrogenation approaches to obtain H-TiO2 have been developed, such as high temperature hydrogen furnace tube annealing, high pressure hydrogen annealing, hydrogen-plasma assisted reaction, aluminum reduction and electrochemical reduction etc., there is still a lack of a hydrogenation approach in a controlled manner where all processing parameters (temperature, time and hydrogen flux) were precisely controlled in order to improve the PEC performance of H-TiO2 and understand the physical insight of enhanced PEC performance. Here, we report for the first time a controlled and local rapid thermal annealing (RTA) approach to prepare hydrogenated core-shell H-TiO2 nanorods grown on F:SnO2 (FTO) substrate in order to address the degradation issue of FTO in the typical TiO2 nanorods/FTO system observed in the conventional non-RTA treated approaches. Without the FTO degradation in the RTA approach, we systematically studied the intrinsic relationship between the annealing temperature, structural, optical, and photoelectrochemical properties in order to understand the role of the disordered shell on the improved photoelectrochemical behavior of H-TiO2 nanorods. Our investigation shows that the improvement of PEC performance could be attributed to (i) band gap narrowing from 3.0 to 2.9 eV; (ii) improved optical absorption in the visible range induced by the three-dimensional (3D) morphology and rough surface of the disordered shell; (iii) increased proper donor density; (iv) enhanced electron-hole separation and injection efficiency due to the formation of disordered shell after hydrogenation. The RTA approach developed here can be used as a suitable hydrogenation process for TiO2 nanorods/FTO system for important applications such as photocatalysis, hydrogen generation from water splitting and solar energy conversion.

Enhanced Photoelectrochemical Behavior of H-TiO2 Nanorods Hydrogenated by Controlled and Local Rapid Thermal Annealing.

PubMed

Wang, Xiaodan; Estradé, Sonia; Lin, Yuanjing; Yu, Feng; Lopez-Conesa, Lluis; Zhou, Hao; Gurram, Sanjeev Kumar; Peiró, Francesca; Fan, Zhiyong; Shen, Hao; Schaefer, Lothar; Braeuer, Guenter; Waag, Andreas

2017-12-01

Recently, colored H-doped TiO 2 (H-TiO 2 ) has demonstrated enhanced photoelectrochemical (PEC) performance due to its unique crystalline core-disordered shell nanostructures and consequent enhanced conduction behaviors between the core-shell homo-interfaces. Although various hydrogenation approaches to obtain H-TiO 2 have been developed, such as high temperature hydrogen furnace tube annealing, high pressure hydrogen annealing, hydrogen-plasma assisted reaction, aluminum reduction and electrochemical reduction etc., there is still a lack of a hydrogenation approach in a controlled manner where all processing parameters (temperature, time and hydrogen flux) were precisely controlled in order to improve the PEC performance of H-TiO 2 and understand the physical insight of enhanced PEC performance. Here, we report for the first time a controlled and local rapid thermal annealing (RTA) approach to prepare hydrogenated core-shell H-TiO 2 nanorods grown on F:SnO 2 (FTO) substrate in order to address the degradation issue of FTO in the typical TiO 2 nanorods/FTO system observed in the conventional non-RTA treated approaches. Without the FTO degradation in the RTA approach, we systematically studied the intrinsic relationship between the annealing temperature, structural, optical, and photoelectrochemical properties in order to understand the role of the disordered shell on the improved photoelectrochemical behavior of H-TiO 2 nanorods. Our investigation shows that the improvement of PEC performance could be attributed to (i) band gap narrowing from 3.0 to 2.9 eV; (ii) improved optical absorption in the visible range induced by the three-dimensional (3D) morphology and rough surface of the disordered shell; (iii) increased proper donor density; (iv) enhanced electron-hole separation and injection efficiency due to the formation of disordered shell after hydrogenation. The RTA approach developed here can be used as a suitable hydrogenation process for TiO 2 nanorods/FTO system for important applications such as photocatalysis, hydrogen generation from water splitting and solar energy conversion.

A pilot evaluation study of the Picture Exchange Communication System (PECS) for children with autistic spectrum disorders.

PubMed

Magiati, Iliana; Howlin, Patricia

2003-09-01

A pilot study was conducted to evaluate the effects of training teachers of children with autistic spectrum disorders (ASDs) in the use of the Picture Exchange Communication System (PECS). Thirty-four children with ASDs (29 boys and 5 girls) were selected from eight specialist schools. Teaching staff attended a 2 day PECS workshop and received six half-day visits from PECS consultants. Data on the children's use of PECS, spontaneous communication, and adaptive behaviour were collected before the study and at set times following the workshop. Significant, rapid increases were recorded in the level of PECS attained by the children, in their PECS vocabulary, and in their frequency of PECS use over time. Improvements in children's general level of communication were slower to occur. The majority of participants showed improvements in their ability to use PECS. The results are discussed in relation to the methodological and practical difficulties that arose during the project.

A Pilot Evaluation Study of the Picture Exchange Communication System (PECS) for Children with Autistic Spectrum Disorders.

ERIC Educational Resources Information Center

Magiati, Iliana; Howlin, Patricia

2003-01-01

A study evaluated the effects of training 47 teachers of children with autism in the use of the Picture Exchange Communication System (PECS). Following training, significant, rapid increases were recorded in the level of PECS attained by the students (n=34), in students' PECS vocabulary, and in students' use of PECS. (Contains references.) (CR)

Subtotal Ablation of Parietal Epithelial Cells Induces Crescent Formation

PubMed Central

Sicking, Eva-Maria; Fuss, Astrid; Uhlig, Sandra; Jirak, Peggy; Dijkman, Henry; Wetzels, Jack; Engel, Daniel R.; Urzynicok, Torsten; Heidenreich, Stefan; Kriz, Wilhelm; Kurts, Christian; Ostendorf, Tammo; Floege, Jürgen; Smeets, Bart

2012-01-01

Parietal epithelial cells (PECs) of the renal glomerulus contribute to the formation of both cellular crescents in rapidly progressive GN and sclerotic lesions in FSGS. Subtotal transgenic ablation of podocytes induces FSGS but the effect of specific ablation of PECs is unknown. Here, we established an inducible transgenic mouse to allow subtotal ablation of PECs. Proteinuria developed during doxycycline-induced cellular ablation but fully reversed 26 days after termination of doxycycline administration. The ablation of PECs was focal, with only 30% of glomeruli exhibiting histologic changes; however, the number of PECs was reduced up to 90% within affected glomeruli. Ultrastructural analysis revealed disruption of PEC plasma membranes with cytoplasm shedding into Bowman’s space. Podocytes showed focal foot process effacement, which was the most likely cause for transient proteinuria. After >9 days of cellular ablation, the remaining PECs formed cellular extensions to cover the denuded Bowman’s capsule and expressed the activation marker CD44 de novo. The induced proliferation of PECs persisted throughout the observation period, resulting in the formation of typical cellular crescents with periglomerular infiltrate, albeit without accompanying proteinuria. In summary, subtotal ablation of PECs leads the remaining PECs to react with cellular activation and proliferation, which ultimately forms cellular crescents. PMID:22282596

Zoonotic Potential of Escherichia coli Isolates from Retail Chicken Meat Products and Eggs

PubMed Central

Mitchell, Natalie M.; Johnson, James R.; Johnston, Brian; Curtiss, Roy

2014-01-01

Chicken products are suspected as a source of extraintestinal pathogenic Escherichia coli (ExPEC), which causes diseases in humans. The zoonotic risk to humans from chicken-source E. coli is not fully elucidated. To clarify the zoonotic risk posed by ExPEC in chicken products and to fill existing knowledge gaps regarding ExPEC zoonosis, we evaluated the prevalence of ExPEC on shell eggs and compared virulence-associated phenotypes between ExPEC and non-ExPEC isolates from both chicken meat and eggs. The prevalence of ExPEC among egg-source isolates was low, i.e., 5/108 (4.7%). Based on combined genotypic and phenotypic screening results, multiple human and avian pathotypes were represented among the chicken-source ExPEC isolates, including avian-pathogenic E. coli (APEC), uropathogenic E. coli (UPEC), neonatal meningitis E. coli (NMEC), and sepsis-associated E. coli (SEPEC), as well as an undefined ExPEC group, which included isolates with fewer virulence factors than the APEC, UPEC, and NMEC isolates. These findings document a substantial prevalence of human-pathogenic ExPEC-associated genes and phenotypes among E. coli isolates from retail chicken products and identify key virulence traits that could be used for screening. PMID:25480753

Numerical study of the effects of lamp configuration and reactor wall roughness in an open channel water disinfection UV reactor.

PubMed

Sultan, Tipu

2016-07-01

This article describes the assessment of a numerical procedure used to determine the UV lamp configuration and surface roughness effects on an open channel water disinfection UV reactor. The performance of the open channel water disinfection UV reactor was numerically analyzed on the basis of the performance indictor reduction equivalent dose (RED). The RED values were calculated as a function of the Reynolds number to monitor the performance. The flow through the open channel UV reactor was modelled using a k-ε model with scalable wall function, a discrete ordinate (DO) model for fluence rate calculation, a volume of fluid (VOF) model to locate the unknown free surface, a discrete phase model (DPM) to track the pathogen transport, and a modified law of the wall to incorporate the reactor wall roughness effects. The performance analysis was carried out using commercial CFD software (ANSYS Fluent 15.0). Four case studies were analyzed based on open channel UV reactor type (horizontal and vertical) and lamp configuration (parallel and staggered). The results show that lamp configuration can play an important role in the performance of an open channel water disinfection UV reactor. The effects of the reactor wall roughness were Reynolds number dependent. The proposed methodology is useful for performance optimization of an open channel water disinfection UV reactor. Copyright © 2016 Elsevier Ltd. All rights reserved.

Parietal cells-new perspectives in glomerular disease.

PubMed

Miesen, Laura; Steenbergen, Eric; Smeets, Bart

2017-07-01

In normal glomeruli, parietal epithelial cells (PECs) line the inside of Bowman's capsule and form an inconspicuous sheet of flat epithelial cells in continuity with the proximal tubular epithelial cells (PTECs) at the urinary pole and with the podocytes at the vascular pole. PECs, PTECs and podocytes have a common mesenchymal origin and are the result of divergent differentiation during embryogenesis. Podocytes and PTECs are highly differentiated cells with well-established functions pertaining to the maintenance of the filtration barrier and transport, respectively. For PECs, no specific function other than a structural one has been known until recently. Possible important functions for PECs in the fate of the glomerulus in glomerular disease have now become apparent: (1) PECs may be involved in the replacement of lost podocytes; (2) PECs form the basis of extracapillary proliferative lesions and subsequent sclerosis in glomerular disease. In addition to the acknowledgement that PECs are crucial in glomerular disease, knowledge has been gained regarding the molecular processes driving the phenotypic changes and behavior of PECs. Understanding these molecular processes is important for the development of specific therapeutic approaches aimed at either stimulation of the regenerative function of PECs or inhibition of the pro-sclerotic action of PECs. In this review, we discuss recent advances pertaining to the role of PECs in glomerular regeneration and disease and address the major molecular processes involved.

Measuring patient experience in dialysis: a new paradigm of quality assessment.

PubMed

Rhee, Connie M; Brunelli, Steven M; Subramanian, Lalita; Tentori, Francesca

2018-04-01

Patients' experience of care (PEC) is as an important dimension in quality of care. As a distinct entity from patient satisfaction and patient health-related quality of life, PEC is defined as patients' perceptions of the range of interactions they have with the health care system, including care from providers, facilities, and health plans. While traditionally PEC may be ascertained via informal assessments, in recent years, especially in the United States, there has been a shift towards standardized surveillance of PEC amongst dialysis patients in order to: (1) set a normative expectation regarding the importance of PEC; (2) standardize the components of patients' experience that are assessed to minimize potential "blind spots"; (3) provide a direct "voice" to the patient in communicating perceptions of their care; (4) facilitate comparisons of quality across facilities; and (5) broaden accountability for PEC to the entire multidisciplinary dialysis care team. In this review, we will discuss the significance of PEC as a quality of care metric in dialysis patients; the history of PEC assessment across other health care arenas; the development of the In-Center Hemodialysis Consumer Assessment of Healthcare Provider and Systems survey as a means to standardize PEC assessment among US dialysis patients; experiences in PEC assessment across international dialysis populations; and future areas of research needed to refine the ascertainment of PEC and its impact upon patient outcomes.

Effects of organoclay to miscibility, mechanical and thermal properties of poly(lactic acid) and propylene-ethylene copolymer blends

NASA Astrophysics Data System (ADS)

Wacharawichanant, S.; Ounyai, C.; Rassamee, P.

2017-07-01

The effects of propylene-ethylene copolymer (PEC or PEC3300) and clay surface modified with 25-30 wt% of trimethylstearyl ammonium (Clay-TSA) on morphology, thermal and mechanical properties of poly(lactic acid) (PLA) were investigated. The morphology analysis showed PLA/PEC3300 blends clearly demonstrated a two-phase separation of dispersed phase and the matrix phase and the addition of Clay-TSA could improve the miscibility of PLA and PEC3300 blends due to the decreased of the domain sizes of dispersed PEC3300 phase in the polymer matrix. From X-ray diffraction analysis showed the intercalation of PLA chains inside the Clay-TSA and this result implied that Clay-TSA platelets acted as an effective compatibilizer. The tensile properties showed the strain at break of PLA was improved after adding PEC3300 while Young’s modulus, tensile strength and storage modulus decreased. The addition of Clay-TSA could improve Young’s modulus of PLA/PEC3300 blends. The addition of Clay-TSA 7 phr showed the maximum of Young’s modulus of PLA/PEC3300/Clay-TSA composites. The thermal properties found that the addition of PEC3300 and Clay-TSA did not change significantly on the glass transition temperature and melting point temperature of PLA. The percent of crystallinity of PLA decreased with increasing PEC content. The thermal stability of PLA improved after adding PEC3300.

Technical note: Influence of surface roughness and local turbulence on coated-wall flow tube experiments for gas uptake and kinetic studies

NASA Astrophysics Data System (ADS)

Li, Guo; Su, Hang; Kuhn, Uwe; Meusel, Hannah; Ammann, Markus; Shao, Min; Pöschl, Ulrich; Cheng, Yafang

2018-02-01

Coated-wall flow tube reactors are frequently used to investigate gas uptake and heterogeneous or multiphase reaction kinetics under laminar flow conditions. Coating surface roughness may potentially distort the laminar flow pattern, induce turbulence and introduce uncertainties in the calculated uptake coefficient based on molecular diffusion assumptions (e.g., Brown/Cooney-Kim-Davis (CKD)/Knopf-Pöschl-Shiraiwa (KPS) methods), which has not been fully resolved in earlier studies. Here, we investigate the influence of surface roughness and local turbulence on coated-wall flow tube experiments for gas uptake and kinetic studies. According to laminar boundary theory and considering the specific flow conditions in a coated-wall flow tube, we derive and propose a critical height δc to evaluate turbulence effects in the design and analysis of coated-wall flow tube experiments. If a geometric coating thickness δg is larger than δc, the roughness elements of the coating may cause local turbulence and result in overestimation of the real uptake coefficient (γ). We further develop modified CKD/KPS methods (i.e., CKD-LT/KPS-LT) to account for roughness-induced local turbulence effects. By combination of the original methods and their modified versions, the maximum error range of γCKD (derived with the CKD method) or γKPS (derived with the KPS method) can be quantified and finally γ can be constrained. When turbulence is generated, γCKD or γKPS can bear large difference compared to γ. Their difference becomes smaller for gas reactants with lower uptake (i.e., smaller γ) and/or for a smaller ratio of the geometric coating thickness to the flow tube radius (δg / R0). On the other hand, the critical height δc can also be adjusted by optimizing flow tube configurations and operating conditions (i.e., tube diameter, length, and flow velocity), to ensure not only unaffected laminar flow patterns but also other specific requirements for an individual flow tube experiment. We use coating thickness values from previous coated-wall flow tube studies to assess potential roughness effects using the δc criterion. In most studies, the coating thickness was sufficiently small to avoid complications, but some may have been influenced by surface roughness and local turbulence effects.

Mixed convection heat transfer enhancement in a cubic lid-driven cavity containing a rotating cylinder through the introduction of artificial roughness on the heated wall

NASA Astrophysics Data System (ADS)

Kareem, Ali Khaleel; Gao, Shian

2018-02-01

The aim of the present numerical investigation is to comprehensively analyse and understand the heat transfer enhancement process using a roughened, heated bottom wall with two artificial rib types (R-s and R-c) due to unsteady mixed convection heat transfer in a 3D moving top wall enclosure that has a central rotating cylinder, and to compare these cases with the smooth bottom wall case. These different cases (roughened and smooth bottom walls) are considered at various clockwise and anticlockwise rotational speeds, -5 ≤ Ω ≤ 5, and Reynolds numbers of 5000 and 10 000. The top and bottom walls of the lid-driven cavity are differentially heated, whilst the remaining cavity walls are assumed to be stationary and adiabatic. A standard k-ɛ model for the Unsteady Reynolds-Averaged Navier-Stokes equations is used to deal with the turbulent flow. The heat transfer improvement is carefully considered and analysed through the detailed examinations of the flow and thermal fields, the turbulent kinetic energy, the mean velocity profiles, the wall shear stresses, and the local and average Nusselt numbers. It has been concluded that artificial roughness can strongly affect the thermal fields and fluid flow patterns. Ultimately, the heat transfer rate has been dramatically increased by involving the introduced artificial rips. Increasing the cylinder rotational speed or Reynolds number can enhance the heat transfer process, especially when the wall roughness exists.

Influence of the three-dimensional heterogeneous roughness on electrokinetic transport in microchannels.

PubMed

Hu, Yandong; Werner, Carsten; Li, Dongqing

2004-12-15

Surface roughness has been considered as a passive means of enhancing species mixing in electroosmotic flow through microfluidic systems. It is highly desirable to understand the synergetic effect of three-dimensional (3D) roughness and surface heterogeneity on the electrokinetic flow through microchannels. In this study, we developed a three-dimensional finite-volume-based numerical model to simulate electroosmotic transport in a slit microchannel (formed between two parallel plates) with numerous heterogeneous prismatic roughness elements arranged symmetrically and asymmetrically on the microchannel walls. We consider that all 3D prismatic rough elements have the same surface charge or zeta potential, the substrate (the microchannel wall) surface has a different zeta potential. The results showed that the rough channel's geometry and the electroosmotic mobility ratio of the roughness elements' surface to that of the substrate, epsilon(mu), have a dramatic influence on the induced-pressure field, the electroosmotic flow patterns, and the electroosmotic flow rate in the heterogeneous rough microchannels. The associated sample-species transport presents a tidal-wave-like concentration field at the intersection between four neighboring rough elements under low epsilon(mu) values and has a concentration field similar to that of the smooth channels under high epsilon(mu) values.

Prediction of an internal boundary layer on a flat plate after a step change in roughness using a near-wall RANS model

NASA Astrophysics Data System (ADS)

Chu, Minghan; Meng, Fanxiao; Bergstrom, Donald J.

2017-11-01

An in-house computational fluid dynamics code was used to simulate turbulent flow over a flat plate with a step change in roughness, exhibiting a smooth-rough-smooth configuration. An internal boundary layer (IBL) is formed at the transition from the smooth to rough (SR) and then the rough to smooth (RS) surfaces. For an IBL the flow far above the surface has experienced a wall shear stress that is different from the local value. Within a Reynolds-Averaged-Navier-Stokes (RANS) formulation, the two-layer k- ɛ model of Durbin et al. (2001) was implemented to analyze the response of the flow to the change in surface condition. The numerical results are compared to experimental data, including some in-house measurements and the seminal work of Antonia and Luxton (1971,72). This problem captures some aspects of roughness in industrial and environmental applications, such as corrosion and the earth's surface heterogeneity, where the roughness is often encountered as discrete distributions. It illustrates the challenge of incorporating roughness models in RANS that are capable of responding to complex surface roughness profiles.

Effect of Surface Roughness on Polymer Drag Reduction with a High-Reynolds-Number Turbulent Boundary Layer

NASA Astrophysics Data System (ADS)

Elbing, Brian; Dowling, David; Solomon, Michael; Bian, Sherry; Ceccio, Steven

2007-11-01

A recent experiment at the U.S. Navy's Large Cavitation Channel (LCC) investigated the effect of wall roughness on wall-injection polymer drag reduction (PDR) within a high-Reynolds-number (10^7 to 2x10^8 based on downstream distance) turbulent boundary layer (TBL). Testing was performed in two parts: 1) PDR experiment on a 12.9 m long, 3.05 m wide hydro-dynamically smooth flat plate and 2) PDR experiment on the same model with the entire surface roughened. The roughness was produced by blowing glass beads into epoxy paint that was applied to the entire model. The roughened model had an average roughness height ranging between 307 and 1154 μm. Drag reduction was determined using six, stream-wise located integrated skin-friction balances. In addition to skin-friction measurements, sampling was performed at three stream-wise located ports. The sampling ports were used to determine the amount of degradation, if any, caused by the turbulent flow on the polymer. Both the skin-friction measurements and sampling analysis indicates that wall roughness in a turbulent boundary layer significantly increases degradation of the polymer solution.

Isolation and characterization of polygalacturonase genes (pecA and pecB) from Aspergillus flavus.

PubMed Central

Whitehead, M P; Shieh, M T; Cleveland, T E; Cary, J W; Dean, R A

1995-01-01

Two genes, pecA and pecB, encoding endopolyglacturonases were cloned from a highly aggressive strain of Aspergillus flavus. The pecA gene consisted of 1,228 bp encoding a protein of 363 amino acids with a predicted molecular mass of 37.6 kDa, interrupted by two introns of 58 and 81 bp in length. Accumulation of pecA mRNA in both pectin- or glucose-grown mycelia in the highly aggressive strain matched the activity profile of a pectinase previously identified as P2c. Transformants of a weakly aggressive strain containing a functional copy of the pecA gene produced P2c in vitro, confirming that pecA encodes P2c. The coding region of pecB was determined to be 1,217 bp in length interrupted by two introns of 65 and 54 bp in length. The predicted protein of 366 amino acids had an estimated molecular mass of 38 kDa. Transcripts of this gene accumulated in mycelia grown in medium containing pectin alone, never in mycelia grown in glucose-containing medium, for both highly and weakly aggressive strains. Thus, pecB encodes the activity previously identified as P1 or P3. pecA and pecB share a high degree of sequence identity with polygalacturonase genes from Aspergillus parasiticus and Aspergillus oryzae, further establishing the close relationships between members of the A. flavus group. Conservation of intron positions in these genes also indicates that they share a common ancestor with genes encoding endopolyglacturonases of Aspergillus niger. PMID:7574642

Characterization of Extraintestinal Pathogenic Escherichia coli isolated from retail poultry meats from Alberta, Canada.

PubMed

Aslam, Mueen; Toufeer, Mehdi; Narvaez Bravo, Claudia; Lai, Vita; Rempel, Heidi; Manges, Amee; Diarra, Moussa Sory

2014-05-02

Extraintestinal Pathogenic Escherichia coli (ExPEC) have the potential to spread through fecal waste resulting in the contamination of both farm workers and retail poultry meat in the processing plants or environment. The objective of this study was to characterize ExPEC from retail poultry meats purchased from Alberta, Canada and to compare them with 12 human ExPEC representatives from major ExPEC lineages. Fifty-four virulence genes were screened by a set of multiplex PCRs in 700 E. coli from retail poultry meat samples. ExPEC was defined as the detection of at least two of the following virulence genes: papA/papC, sfa, kpsMT II and iutA. Genetic relationships between isolates were determined using pulsed field gel electrophoresis (PFGE). Fifty-nine (8.4%) of the 700 poultry meat isolates were identified as ExPEC and were equally distributed among the phylogenetic groups A, B1, B2 and D. Isolates of phylogenetic group A possessed up to 12 virulence genes compared to 24 and 18 genes in phylogenetic groups B2 and D, respectively. E. coli identified as ExPEC and recovered from poultry harbored as many virulence genes as those of human isolates. In addition to the iutA gene, siderophore-related iroN and fyuA were detected in combination with other virulence genes including those genes encoding for adhesion, protectin and toxin while the fimH, ompT, traT, uidA and vat were commonly detected in poultry ExPEC. The hemF, iss and cvaC genes were found in 40% of poultry ExPEC. All human ExPEC isolates harbored concnf (cytotoxic necrotizing factor 1 altering cytoskeleton and causing necrosis) and hlyD (hemolysin transport) genes which were not found in poultry ExPEC. PFGE analysis showed that a few poultry ExPEC isolates clustered with human ExPEC isolates at 55-70% similarity level. Comparing ExPEC isolated from retail poultry meats provides insight into their virulence potential and suggests that poultry associated ExPEC may be important for retail meat safety. Investigations into the ability of our poultry ExPEC to cause human infections are warranted. Crown Copyright © 2014. Published by Elsevier B.V. All rights reserved.

Supersonic turbulent boundary layers with periodic mechanical non-equilibrium

NASA Astrophysics Data System (ADS)

Ekoto, Isaac Wesley

Previous studies have shown that favorable pressure gradients reduce the turbulence levels and length scales in supersonic flow. Wall roughness has been shown to reduce the large-scales in wall bounded flow. Based on these previous observations new questions have been raised. The fundamental questions this dissertation addressed are: (1) What are the effects of wall topology with sharp versus blunt leading edges? and (2) Is it possible that a further reduction of turbulent scales can occur if surface roughness and favorable pressure gradients are combined? To answer these questions and to enhance the current experimental database, an experimental analysis was performed to provide high fidelity documentation of the mean and turbulent flow properties along with surface and flow visualizations of a high-speed (M = 2.86), high Reynolds number (Retheta ≈ 60,000) supersonic turbulent boundary layer distorted by curvature-induced favorable pressure gradients and large-scale ( k+s ≈ 300) uniform surface roughness. Nine models were tested at three separate locations. Three pressure gradient models strengths (a nominally zero, a weak, and a strong favorable pressure gradient) and three roughness topologies (aerodynamically smooth, square, and diamond shaped roughness elements) were used. Highly resolved planar measurements of mean and fluctuating velocity components were accomplished using particle image velocimetry. Stagnation pressure profiles were acquired with a traversing Pitot probe. Surface pressure distributions were characterized using pressure sensitive paint. Finally flow visualization was accomplished using schlieren photographs. Roughness topology had a significant effect on the boundary layer mean and turbulent properties due to shock boundary layer interactions. Favorable pressure gradients had the expected stabilizing effect on turbulent properties, but the improvements were less significant for models with surface roughness near the wall due to increased tendency towards flow separation. It was documented that proper roughness selection coupled with a sufficiently strong favorable pressure gradient produced regions of "negative" production in the transport of turbulent stress. This led to localized areas of significant turbulence stress reduction. With proper roughness selection and sufficient favorable pressure gradient strength, it is believed that localized relaminarization of the boundary layer is possible.

Implementing the picture exchange communication system (PECS).

PubMed

Liddle, K

2001-01-01

PECS was developed in Delaware, USA over 10 years ago by Bondy and Frost (1994a). Over the last two years PECS has been introduced to this country and has raised a great deal of interest in people working in the field of autistic spectrum disorders (ASD). This paper will address some of the issues that arose during the establishment of PECS in one special school. Changes seen in 21 children with severe learning difficulties who have been taught to use PECS are reported and the use of PECS with children who do not have an ASD is discussed.

Zoonotic potential of Escherichia coli isolates from retail chicken meat products and eggs.

PubMed

Mitchell, Natalie M; Johnson, James R; Johnston, Brian; Curtiss, Roy; Mellata, Melha

2015-02-01

Chicken products are suspected as a source of extraintestinal pathogenic Escherichia coli (ExPEC), which causes diseases in humans. The zoonotic risk to humans from chicken-source E. coli is not fully elucidated. To clarify the zoonotic risk posed by ExPEC in chicken products and to fill existing knowledge gaps regarding ExPEC zoonosis, we evaluated the prevalence of ExPEC on shell eggs and compared virulence-associated phenotypes between ExPEC and non-ExPEC isolates from both chicken meat and eggs. The prevalence of ExPEC among egg-source isolates was low, i.e., 5/108 (4.7%). Based on combined genotypic and phenotypic screening results, multiple human and avian pathotypes were represented among the chicken-source ExPEC isolates, including avian-pathogenic E. coli (APEC), uropathogenic E. coli (UPEC), neonatal meningitis E. coli (NMEC), and sepsis-associated E. coli (SEPEC), as well as an undefined ExPEC group, which included isolates with fewer virulence factors than the APEC, UPEC, and NMEC isolates. These findings document a substantial prevalence of human-pathogenic ExPEC-associated genes and phenotypes among E. coli isolates from retail chicken products and identify key virulence traits that could be used for screening. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Process Parameters Optimization in Single Point Incremental Forming

NASA Astrophysics Data System (ADS)

Gulati, Vishal; Aryal, Ashmin; Katyal, Puneet; Goswami, Amitesh

2016-04-01

This work aims to optimize the formability and surface roughness of parts formed by the single-point incremental forming process for an Aluminium-6063 alloy. The tests are based on Taguchi's L18 orthogonal array selected on the basis of DOF. The tests have been carried out on vertical machining center (DMC70V); using CAD/CAM software (SolidWorks V5/MasterCAM). Two levels of tool radius, three levels of sheet thickness, step size, tool rotational speed, feed rate and lubrication have been considered as the input process parameters. Wall angle and surface roughness have been considered process responses. The influential process parameters for the formability and surface roughness have been identified with the help of statistical tool (response table, main effect plot and ANOVA). The parameter that has the utmost influence on formability and surface roughness is lubrication. In the case of formability, lubrication followed by the tool rotational speed, feed rate, sheet thickness, step size and tool radius have the influence in descending order. Whereas in surface roughness, lubrication followed by feed rate, step size, tool radius, sheet thickness and tool rotational speed have the influence in descending order. The predicted optimal values for the wall angle and surface roughness are found to be 88.29° and 1.03225 µm. The confirmation experiments were conducted thrice and the value of wall angle and surface roughness were found to be 85.76° and 1.15 µm respectively.

Analysis of turbulent heat and momentum transfer in a transitionally rough turbulent boundary layer

NASA Astrophysics Data System (ADS)

Doosttalab, Ali; Dharmarathne, Suranga; Tutkun, Murat; Adrian, Ronald; Castillo, Luciano

2016-11-01

A zero-pressure-gradient (ZPG) turbulent boundary layer over a transitionally rough surface is studied using direct numerical simulation (DNS). The rough surface is modeled as 24-grit sandpaper which corresponds to k+ 11 , where k+ is roughness height. Reynolds number based on momentum thickness is approximately 2400. The walls are isothermal and turbulent flow Prandtl number is 0.71. We simulate temperature as passive scalar. We compute the inner product of net turbulent force (d (u1ui) / dxi) and net turbulent heat flux (d (ui θ / dxi)) in order to investigate (i) the correlation between these vectorial quantities, (II) size of the projection of these fields on each other and (IIi) alignment of momentum and hear flux. The inner product in rough case results in larger projection and better alignment. In addition, our study on the vortices shows that surface roughness promotes production of vortical structures which affects the thermal transport near the wall.

ACTIVE PEC APPLICATIONS, THE PEC WEBSITE, AND SLUDGE STABILITY RESEARCH

EPA Science Inventory

Since it's creation in 1985, the Pathogen Equivalency Committee (PEC) has been reviewing novel sludge disinfection technologies with regards to their abilities to protect human health and the environment. The PEC is charged to make recommendations on whether these novel technolog...

A comparison RSM and ANN surface roughness models in thin-wall machining of Ti6Al4V using vegetable oils under MQL-condition

NASA Astrophysics Data System (ADS)

Mohruni, Amrifan Saladin; Yanis, Muhammad; Sharif, Safian; Yani, Irsyadi; Yuliwati, Erna; Ismail, Ahmad Fauzi; Shayfull, Zamree

2017-09-01

Thin-wall components as usually applied in the structural parts of aeronautical industry require significant challenges in machining. Unacceptable surface roughness can occur during machining of thin-wall. Titanium product such Ti6Al4V is mostly applied to get the appropriate surface texture in thin wall designed requirements. In this study, the comparison of the accuracy between Response Surface Methodology (RSM) and Artificial Neural Networks (ANN) in the prediction of surface roughness was conducted. Furthermore, the machining tests were carried out under Minimum Quantity Lubrication (MQL) using AlCrN-coated carbide tools. The use of Coconut oil as cutting fluids was also chosen in order to evaluate its performance when involved in end milling. This selection of cutting fluids is based on the better performance of oxidative stability than that of other vegetable based cutting fluids. The cutting speed, feed rate, radial and axial depth of cut were used as independent variables, while surface roughness is evaluated as the dependent variable or output. The results showed that the feed rate is the most significant factors in increasing the surface roughness value followed by the radial depth of cut and lastly the axial depth of cut. In contrary, the surface becomes smoother with increasing the cutting speed. From a comparison of both methods, the ANN model delivered a better accuracy than the RSM model.

Experimental Investigation of Roughness Effects on Transition Onset and Turbulent Heating Augmentation on a Hemisphere at Mach 6 and Mach 10

NASA Technical Reports Server (NTRS)

Hollis, Brian R.

2017-01-01

An experimental investigation of the effects of distributed surface roughness on boundary-layer transition and turbulent heating has been conducted. Hypersonic wind tunnel testing was performed using hemispherical models with surface roughness patterns simulating those produced by heat shield ablation. Global aeroheating and transition onset data were obtained using phosphor thermography at Mach 6 and Mach 10 over a range of roughness heights and free stream Reynolds numbers sufficient to produce laminar, transitional and turbulent flow. Upstream movement of the transition onset location and increasing heating augmentation over predicted smooth-wall levels were observed with both increasing roughness heights and increasing free stream Reynolds numbers. The experimental heating data are presented herein, as are comparisons to smooth-wall heat transfer distributions from computational flow-field simulations. The transition onset data are also tabulated, and correlations of these data are presented.

MicroRNA-193a Regulates the Transdifferentiation of Human Parietal Epithelial Cells toward a Podocyte Phenotype

PubMed Central

Kietzmann, Leonie; Guhr, Sebastian S.O.; Meyer, Tobias N.; Ni, Lan; Sachs, Marlies; Panzer, Ulf; Stahl, Rolf A.K.; Saleem, Moin A.; Kerjaschki, Dontscho; Gebeshuber, Christoph A.

2015-01-01

Parietal epithelial cells have been identified as potential progenitor cells in glomerular regeneration, but the molecular mechanisms underlying this process are not fully defined. Here, we established an immortalized polyclonal human parietal epithelial cell (hPEC) line from naive human Bowman’s capsule cells isolated by mechanical microdissection. These hPECs expressed high levels of PEC-specific proteins and microRNA-193a (miR-193a), a suppressor of podocyte differentiation through downregulation of Wilms’ tumor 1 in mice. We then investigated the function of miR-193a in the establishment of podocyte and PEC identity and determined whether inhibition of miR-193a influences the behavior of PECs in glomerular disease. After stable knockdown of miR-193a, hPECs adopted a podocyte-like morphology and marker expression, with decreased expression levels of PEC markers. In mice, inhibition of miR-193a by complementary locked nucleic acids resulted in an upregulation of the podocyte proteins synaptopodin and Wilms’ tumor 1. Conversely, overexpression of miR-193a in vivo resulted in the upregulation of PEC markers and the loss of podocyte markers in isolated glomeruli. Inhibition of miR-193a in a mouse model of nephrotoxic nephritis resulted in reduced crescent formation and decreased proteinuria. Together, these results show the establishment of a human PEC line and suggest that miR-193a functions as a master switch, such that glomerular epithelial cells with high levels of miR-193a adopt a PEC phenotype and cells with low levels of miR-193a adopt a podocyte phenotype. miR-193a–mediated maintenance of PECs in an undifferentiated reactive state might be a prerequisite for PEC proliferation and migration in crescent formation. PMID:25270065

Single-shot pectoral plane (PECs I and PECs II) blocks versus continuous local anaesthetic infusion analgesia or both after non-ambulatory breast-cancer surgery: a prospective, randomised, double-blind trial.

PubMed

O'Scanaill, P; Keane, S; Wall, V; Flood, G; Buggy, D J

2018-04-01

Pectoral plane blocks (PECs) are increasingly used in analgesia for patients undergoing breast surgery, and were recently found to be at least equivalent to single-shot paravertebral anaesthesia. However, there are no data comparing PECs with the popular practice of continuous local anaesthetic wound infusion (LA infusion) analgesia for breast surgery. Therefore, we compared the efficacy and safety of PECs blocks with LA infusion, or a combination of both in patients undergoing non-ambulatory breast-cancer surgery. This single-centre, prospective, randomised, double-blind trial analysed 45 women to receive either PECs blocks [levobupivacaine 0.25%, 10 ml PECs I and levobupivacaine 0.25%, 20 ml PECs II (PECs group); LA infusion catheter (levobupivacaine 0.1% at 10 ml h -1 for 24 h (LA infusion group); or both (PECs and LA infusion)]. The primary outcome measure was area under the curve of the pain verbal rating score whilst moving vs time (AUC) over 24 h. Secondary outcomes included total opioid consumption at 24 h. AUC moving was mean (SD) 71 (34) mm h -1 vs 58 (41) vs 23 (20) in PECs, LA infusion, and both, respectively; P=0.002. AUC at rest was also significantly lower in patients receiving both. The total 24 h opioid consumption [median (25-75%)] was 14 mg (9-26) vs 11 (8-24) vs 9 (5-11); P=0.4. No adverse events were observed. The combination of both pre-incisional PECs blocks and postoperative LA infusion provides better analgesia over 24 h than either technique alone after non-ambulatory breast-cancer surgery. NCT 03024697. Copyright © 2018 British Journal of Anaesthesia. Published by Elsevier Ltd. All rights reserved.

Effect of surface morphology on drag and roughness sublayer in flows over regular roughness elements

NASA Astrophysics Data System (ADS)

Placidi, Marco; Ganapathisubramani, Bharathram

2014-11-01

The effects of systematically varied roughness morphology on bulk drag and on the spatial structure of turbulent boundary layers are examined by performing a series of wind tunnel experiments. In this study, rough surfaces consisting of regularly and uniformly distributed LEGO™ bricks are employed. Twelve different patterns are adopted in order to methodically examine the individual effects of frontal solidity (λF, frontal area of the roughness elements per unit wall-parallel area) and plan solidity (λP, plan area of roughness elements per unit wall-parallel area), on both the bulk drag and the turbulence structure. A floating element friction balance based on Krogstad & Efros (2010) was designed and manufactured to measure the drag generated by the different surfaces. In parallel, high resolution planar and stereoscopic Particle Image Velocimetry (PIV) was applied to investigate the flow features. This talk will focus on the effects of each solidity parameter on the bulk drag and attempt to relate the observed trends to the flow structures in the roughness sublayer. Currently at City University London.

Polyelectrolyte Complex Inclusive Biohybrid Microgels for Tailoring Delivery of Copigmented Anthocyanins.

PubMed

Tan, Chen; B Celli, Giovana; Lee, Michelle; Licker, Jonathan; Abbaspourrad, Alireza

2018-05-14

This study fabricated a novel biohybrid microgel containing polysaccharide-based polyelectrolyte complexes (PECs) for anthocyanins. Herein, anthocyanins were encapsulated into PECs composed of chondroitin sulfate and chitosan, followed by incorporation into alginate microgels using emulsification/internal gelation method. We demonstrated that PECs incorporation strongly affected the properties of microgels, dependent on the polysaccharide concentration and pH in which they were fabricated. The dense internal network surrounded by an alginate shell was clearly visualized in cross-sectioned PECs-microgels. Stability studies carried out under varying ionic strength and pH conditions demonstrated the stimuli-responsiveness of the PECs-microgels. Additionally, the presence of PECs conferred microgels with high rigidity during freeze-drying and excellent reconstitution capacity upon rehydration. These observations were attributed to the modulation of electrostatic and hydrogen-bonding cross-linking between PECs and the alginate gel matrix and suggest the PECs inclusive microgels hold promise as delivery vehicles for the controlled release of hydrophilic bioactive compounds.

Principles and applications of photoelectrochemical sensing strategies based on biofunctionalized nanostructures.

PubMed

Zang, Yang; Lei, Jianping; Ju, Huangxian

2017-10-15

Photoelectrochemical (PEC) biosensing is a popular research hotspot that has attracted substantial attention from chemists and biologists due to its low cost and desirable sensitivity. The PEC biosensing mainly refers to the influence of the interaction between recognition element and analyte on photocurrent signal, which involves the charge and energy transfer of PEC reaction between electron donor/acceptor and photoactive material upon light irradiation. Understanding the fundamentals of PEC strategy benefits the development of next-generation PEC sensors. However, the research on detection mechanism of PEC sensors is in the initial stage and need to be further exploited. Thus, with a particular focus on the signal transduction formats, this review highlights the novel concept on PEC sensing strategies, and categorizes the recent illustrative examples into three signaling principles: reactant determinant, electron transfer and energy transfer, providing the comprehensive design guidelines for researchers to develop more advanced PEC sensors. The prospects and challenges for future work are also included. Copyright © 2017 Elsevier B.V. All rights reserved.

Using the picture exchange communication system (PECS) with children with autism: assessment of PECS acquisition, speech, social-communicative behavior, and problem behavior.

PubMed Central

Charlop-Christy, Marjorie H; Carpenter, Michael; Le, Loc; LeBlanc, Linda A; Kellet, Kristen

2002-01-01

The picture exchange communication system (PECS) is an augmentative communication system frequently used with children with autism (Bondy & Frost, 1994; Siegel, 2000; Yamall, 2000). Despite its common clinical use, no well-controlled empirical investigations have been conducted to test the effectiveness of PECS. Using a multiple baseline design, the present study examined the acquisition of PECS with 3 children with autism. In addition, the study examined the effects of PECS training on the emergence of speech in play and academic settings. Ancillary measures of social-communicative behaviors and problem behaviors were recorded. Results indicated that all 3 children met the learning criterion for PECS and showed concomitant increases in verbal speech. Ancillary gains were associated with increases in social-communicative behaviors and decreases in problem behaviors. The results are discussed in terms of the provision of empirical support for PECS as well as the concomitant positive side effects of its use. PMID:12365736

Using the picture exchange communication system (PECS) with children with autism: assessment of PECS acquisition, speech, social-communicative behavior, and problem behavior.

PubMed

Charlop-Christy, Marjorie H; Carpenter, Michael; Le, Loc; LeBlanc, Linda A; Kellet, Kristen

2002-01-01

The picture exchange communication system (PECS) is an augmentative communication system frequently used with children with autism (Bondy & Frost, 1994; Siegel, 2000; Yamall, 2000). Despite its common clinical use, no well-controlled empirical investigations have been conducted to test the effectiveness of PECS. Using a multiple baseline design, the present study examined the acquisition of PECS with 3 children with autism. In addition, the study examined the effects of PECS training on the emergence of speech in play and academic settings. Ancillary measures of social-communicative behaviors and problem behaviors were recorded. Results indicated that all 3 children met the learning criterion for PECS and showed concomitant increases in verbal speech. Ancillary gains were associated with increases in social-communicative behaviors and decreases in problem behaviors. The results are discussed in terms of the provision of empirical support for PECS as well as the concomitant positive side effects of its use.

Albumin-induced apoptosis of glomerular parietal epithelial cells is modulated by extracellular signal-regulated kinase 1/2

PubMed Central

Ohse, Takamoto; Krofft, Ron D.; Wu, Jimmy S.; Eddy, Allison A.; Pippin, Jeffrey W.; Shankland, Stuart J.

2012-01-01

Background. The biological role(s) of glomerular parietal epithelial cells (PECs) is not fully understood in health or disease. Given its location, PECs are constantly exposed to low levels of filtered albumin, which is increased in nephrotic states. We tested the hypothesis that PECs internalize albumin and increased uptake results in apoptosis. Methods. Confocal microscopy of immunofluorescent staining and immunohistochemistry were used to demonstrate albumin internalization in PECs and to quantitate albumin uptake in normal mice and rats as well as experimental models of membranous nephropathy, minimal change disease/focal segmental glomerulosclerosis and protein overload nephropathy. Fluorescence-activated cell sorting analysis was performed on immortalized cultured PECs exposed to fluorescein isothiocyanate (FITC)-labeled albumin in the presence of an endosomal inhibitor or vehicle. Apoptosis was measured by Hoechst staining in cultured PECs exposed to bovine serum albumin. Levels of phosphorylated extracellular signal-regulated kinase 1 and 2 (p-ERK1/2) were restored by retroviral infection of mitogen-activated protein kinase (MEK) 1/2 and reduced by U0126 in PECs exposed to high albumin levels in culture and apoptosis measured by Hoechst staining. Results. PECs internalized albumin normally, and this was markedly increased in all of the experimental disease models (P < 0.05 versus controls). Cultured immortalized PECs also internalize FITC-labeled albumin, which was reduced by endosomal inhibition. A consequence of increased albumin internalization was PEC apoptosis in vitro and in vivo. Candidate signaling pathways underlying these events were examined. Data showed markedly reduced levels of phosphorylated extracellular signal-regulated kinase 1 and 2 (ERK1/2) in PECs exposed to high albumin levels in nephropathy and in culture. A role for ERK1/2 in limiting albumin-induced apoptosis was shown by restoring p-ERK1/2 by retroviral infection, which reduced apoptosis in cultured PECs, while a forced decrease of p-ERK1/2 through inhibition of MEK 1/2 significantly increased albumin-induced PEC apoptosis. Conclusions. A normal role of PECs is to take up filtered albumin. However, this is increased in proteinuric glomerular diseases, leading to apoptosis through changes in ERK1/2. PMID:21896500

Expression and Self-Assembly in Baculovirus of Porcine Enteric Calicivirus Capsids into Virus-Like Particles and Their Use in an Enzyme-Linked Immunosorbent Assay for Antibody Detection in Swine

PubMed Central

Guo, Mingzhang; Qian, Yuan; Chang, Kyeong-Ok; Saif, Linda J.

2001-01-01

Porcine enteric calicivirus (PEC) causes diarrhea and intestinal lesions in pigs. PEC strain Cowden grows to low to moderate titers in cell culture but only with the addition of intestinal contents from uninfected gnotobiotic pigs (W. T. Flynn and L. J. Saif, J. Clin. Microbiol. 26:206–212, 1988; A. V. Parwani, W. T. Flynn, K. L. Gadfield, and L. J. Saif, Arch. Virol. 120:115–122, 1991). Cloning and sequence analysis of the PEC Cowden full-length genome revealed that it is most closely related genetically to the human Sapporo-like viruses. In this study, the complete PEC capsid gene was subcloned into the plasmid pBlueBac4.5 and the recombinant baculoviruses were identified by plaque assay and PCR. The PEC capsid protein was expressed in insect (Sf9) cells inoculated with the recombinant baculoviruses, and the recombinant capsid proteins self- assembled into virus-like particles (VLPs) that were released into the cell supernatant and purified by CsCl gradient centrifugation. The PEC VLPs had the same molecular mass (58 kDa) as the native virus capsid and reacted with pig hyperimmune and convalescent-phase sera to PEC Cowden in enzyme-linked immunosorbent assay (ELISA) and Western blotting. The PEC capsid VLPs were morphologically and antigenically similar to the native virus by immune electron microscopy. High titers (1:102,400 to 204,800) of PEC-specific antibodies were induced in guinea pigs inoculated with PEC VLPs, suggesting that the VLPs could be useful for future candidate PEC vaccines. A fixed-cell ELISA and VLP ELISA were developed to detect PEC serum antibodies in pigs. For the fixed-cell ELISA, Sf9 cells were infected with recombinant baculoviruses expressing PEC capsids, followed by cell fixation with formalin. For the VLP ELISA, the VLPs were used for the coating antigen. Our data indicate that both tests were rapid, specific, and reproducible and might be used for large-scale serological investigations of PEC antibodies in swine. PMID:11283075

New Insights into Glomerular Parietal Epithelial Cell Activation and Its Signaling Pathways in Glomerular Diseases

PubMed Central

Su, Hua; Chen, Shan; He, Fang-Fang; Wang, Yu-Mei; Bondzie, Philip; Zhang, Chun

2015-01-01

The glomerular parietal epithelial cells (PECs) have aroused an increasing attention recently. The proliferation of PECs is the main feature of crescentic glomerulonephritis; besides that, in the past decade, PEC activation has been identified in several types of noninflammatory glomerulonephropathies, such as focal segmental glomerulosclerosis, diabetic glomerulopathy, and membranous nephropathy. The pathogenesis of PEC activation is poorly understood; however, a few studies delicately elucidate the potential mechanisms and signaling pathways implicated in these processes. In this review we will focus on the latest observations and concepts about PEC activation in glomerular diseases and the newest identified signaling pathways in PEC activation. PMID:25866774

Effect of Wall Temperature on Roughness Induced Attachment-Line Transition

NASA Technical Reports Server (NTRS)

Dietz, Anthony; Coleman, Colin; Laub, Jim; Poll, D. I. A.; Nixon, David (Technical Monitor)

1999-01-01

An experiment on a cooled swept cylinder in a low-disturbance Mach 1.6 wind tunnel is described. The flow attachment line is disturbed by trip wires of varying size and the laminar/turbulent state of the downstream boundary layer is determined with a hot wire. The results demonstrate that although cooling the wall increases the stability of the boundary layer, it promotes roughness induced transition. Analysis of the data suggests that the attachment- line Reynolds number can account for the effect of wall cooling if the viscosity is evaluated at a particular reference temperature.

Glomerular parietal epithelial cells contribute to adult podocyte regeneration in experimental focal segmental glomerulosclerosis

PubMed Central

Eng, Diana G.; Sunseri, Maria W.; Kaverina, Natalya; Roeder, Sebastian S.; Pippin, Jeffrey W.; Shankland, Stuart J.

2015-01-01

Since adult podocytes cannot adequately proliferate following depletion in disease states there has been interest in the potential role of progenitors in podocyte repair and regeneration. To determine if parietal epithelial cells (PECs) can serve as adult podocyte progenitors following disease-induced podocyte depletion, PECs were permanently labeled in adult PECrtTA/LC1/R26 reporter mice. In normal mice, labeled PECs were confined to Bowman's capsule, while in disease (cytotoxic sheep anti-podocyte antibody), labeled PECs were found in the glomerular tuft in progressively higher numbers by days 7, 14 and 28. Early in disease, the majority of PECs in the tuft co-expressed CD44. By day 28, when podocyte numbers were significantly higher and disease severity was significantly lower, the majority of labeled PECs co-expressed podocyte proteins but not CD44. Neither labeled PECs on the tuft, nor podocytes stained for the proliferation marker BrdU. The de novo expression of phospho-ERK colocalized to CD44 expressing PECs, but not to PECs expressing podocyte markers. Thus, in a mouse model of focal segmental glomerulosclerosis typified by abrupt podocyte depletion followed by regeneration, PECs undergo two phenotypic changes once they migrate to the glomerular tuft. Initially these cells are predominantly activated CD44 expressing cells coinciding with glomerulosclerosis, and later they predominantly exhibit a podocyte phenotype which is likely reparative. PMID:25993321

Escherichia coli and urinary tract infections: the role of poultry-meat.

PubMed

Manges, A R

2016-02-01

Extraintestinal pathogenic Escherichia coli (ExPEC) is the most common cause of community-acquired and hospital-acquired extraintestinal infections. The hypothesis that human ExPEC may have a food animal reservoir has been a topic of investigation by multiple groups around the world. Experimental studies showing the shared pathogenic potential of human ExPEC and avian pathogenic E. coli suggest that these extraintestinal E. coli may be derived from the same bacterial lineages or share common evolutionary roots. The consistent observation of specific human ExPEC lineages in poultry or poultry products, and rarely in other meat commodities, supports the hypothesis that there may be a poultry reservoir for human ExPEC. The time lag between human ExPEC acquisition (in the intestine) and infection is the fundamental challenge facing studies attempting to attribute ExPEC transmission to poultry or other environmental sources. Even whole genome sequencing efforts to address attribution will struggle with defining meaningful genetic relationships outside of a discrete food-borne outbreak setting. However, if even a fraction of all human ExPEC infections, especially antimicrobial-resistant ExPEC infections, is attributable to the introduction of multidrug-resistant ExPEC lineages through contaminated food product(s), the relevance to public health, food animal production and food safety will be significant. Copyright © 2016 European Society of Clinical Microbiology and Infectious Diseases. Published by Elsevier Ltd. All rights reserved.

Predicting progress in Picture Exchange Communication System (PECS) use by children with autism.

PubMed

Pasco, Greg; Tohill, Christina

2011-01-01

The Picture Exchange Communication System (PECS) is a widely used communication intervention for non-verbal children with autism spectrum disorder. Findings for the benefits of PECS have almost universally been positive, although there is very limited information about the characteristics of PECS users that determine the amount of progress that they are likely to make. To explore the utility of using children's developmental age to predict the subsequent degree of progress using PECS. In a retrospective study, 23 non-verbal 5- and 6-year-old children with autism spectrum disorder attending a special school were assessed to determine their highest level of PECS ability. They were then allocated to one of two groups depending on whether or not they had mastered PECS phase III. All participants had been assessed using the Psycho-Educational Profile-Revised (PEP-R) on entry to the school and before being introduced to PECS. Total developmental age scores were examined to determine whether they accurately predicted membership of the two PECS ability groups. All the 16 children who had mastered PECS phase III had total developmental age scores of 16 months or above, whilst six of the seven children who had not progressed beyond phase III scored below 16 months--the other child had a score of 16 months. The assessment of the developmental level of potential PECS users may provide valuable predictive information for speech-and-language therapists and other professionals in relation to the likely degree of progress and in setting realistic and achievable targets. © 2010 Royal College of Speech & Language Therapists.

Training Paraprofessionals to Implement the Picture Exchange Communication System (PECS)

ERIC Educational Resources Information Center

Sloman, Glenn Matthew

2010-01-01

Based on Skinner's "Verbal Behavior" (1957), the picture exchange communication system (PECS) was designed to teach children with autism functional verbal behavior. Much research has demonstrated the effectiveness and efficiency of PECS in building verbal behavior. However, because PECS training is typically presented in a group format and later…

Roughness topographical effects on mean momentum and stress budgets in developed turbulent channel flows

NASA Astrophysics Data System (ADS)

Aghaei Jouybari, Mostafa; Yuan, Junlin

2017-11-01

Direct numerical simulations of turbulent channel flows are carried out over two surfaces: a synthesized sand-grain surface and a realistic turbine roughness that is characterized by more prominent large-scale surface features. To separate the effects of wall-normal variation of the roughness area fraction from the (true) variation of flow statistics, the governing equations are area-averaged using intrinsic averaging, contrary to the usually practice based on the total area (i.e., superficial averaging). Additional terms appear in the mean-momentum equation resulted from the wall-normal variation of the solid fraction and play a role in the near-wall balance. Results from surfaces with a step solidity function (e.g., cubes) will also be discussed. Compared to the sand grains, the turbine surface generates stronger form-induced fluctuations, despite weaker dispersive shear stress. This is associated with more significant form-induced productions (comparable to shear production) in Reynolds stress budgets, weaker pressure work, and, consequently, more anisotropic redistribution of turbulent kinetic energy in the roughness sublayer, which potentially leads to different turbulent responses between the two surfaces in non-equilibrium flows.

Studies of Real Roughness Effects for Improved Modeling and Control of Practical Wall-Bounded Turbulent Flows

DTIC Science & Technology

2008-04-22

SUPPLEMENTARY NOTES 14. ABSTRACT The present effort investigates the effects of practical roughness replicated from a turbine blade damaged by deposition of...Motivation Most practical wall-bounded turbulent flows of interest, like flows over turbine blades , through heat exchangers, and over aircraft and ship...significantly roughened over time due to harsh operating conditions. Examples of such conditions include cumulative damage to turbine blades (Bons, 2002

Measurements and Modeling of the Mean and Turbulent Flow Structure in High-Speed Rough-Wall Non-Equilibrium Boundary Layers

DTIC Science & Technology

2010-01-25

study builds on three basic bodies of knowledge: (1) supersonic rough wall boundary layers, (2) distorted supersonic turbulent boundary layers, and...with the boundary layer turbulence . The present study showed that secondary distortions associated with such waves significantly affect the transport...38080 14. ABSTRACT The response of a supersonic high Reynolds number turbulent boundary layer flow subjected to mechanical distortions was

Surface correlations of hydrodynamic drag for transitionally rough engineering surfaces

NASA Astrophysics Data System (ADS)

Thakkar, Manan; Busse, Angela; Sandham, Neil

2017-02-01

Rough surfaces are usually characterised by a single equivalent sand-grain roughness height scale that typically needs to be determined from laboratory experiments. Recently, this method has been complemented by a direct numerical simulation approach, whereby representative surfaces can be scanned and the roughness effects computed over a range of Reynolds number. This development raises the prospect over the coming years of having enough data for different types of rough surfaces to be able to relate surface characteristics to roughness effects, such as the roughness function that quantifies the downward displacement of the logarithmic law of the wall. In the present contribution, we use simulation data for 17 irregular surfaces at the same friction Reynolds number, for which they are in the transitionally rough regime. All surfaces are scaled to the same physical roughness height. Mean streamwise velocity profiles show a wide range of roughness function values, while the velocity defect profiles show a good collapse. Profile peaks of the turbulent kinetic energy also vary depending on the surface. We then consider which surface properties are important and how new properties can be incorporated into an empirical model, the accuracy of which can then be tested. Optimised models with several roughness parameters are systematically developed for the roughness function and profile peak turbulent kinetic energy. In determining the roughness function, besides the known parameters of solidity (or frontal area ratio) and skewness, it is shown that the streamwise correlation length and the root-mean-square roughness height are also significant. The peak turbulent kinetic energy is determined by the skewness and root-mean-square roughness height, along with the mean forward-facing surface angle and spanwise effective slope. The results suggest feasibility of relating rough-wall flow properties (throughout the range from hydrodynamically smooth to fully rough) to surface parameters.

Materials International Space Station Experiment (MISSE) 5 Developed to Test Advanced Solar Cell Technology Aboard the ISS

NASA Technical Reports Server (NTRS)

Wilt, David M.

2004-01-01

The testing of new technologies aboard the International Space Station (ISS) is facilitated through the use of a passive experiment container, or PEC, developed at the NASA Langley Research Center. The PEC is an aluminum suitcase approximately 2 ft square and 5 in. thick. Inside the PEC are mounted Materials International Space Station Experiment (MISSE) plates that contain the test articles. The PEC is carried to the ISS aboard the space shuttle or a Russian resupply vehicle, where astronauts attach it to a handrail on the outer surface of the ISS and deploy the PEC, which is to say the suitcase is opened 180 deg. Typically, the PEC is left in this position for approximately 1 year, at which point astronauts close the PEC and it is returned to Earth. In the past, the PECs have contained passive experiments, principally designed to characterize the durability of materials subjected to the ultraviolet radiation and atomic oxygen present at the ISS orbit. The MISSE5 experiment is intended to characterize state-of-art (SOA) and beyond photovoltaic technologies.

Characterization of surface roughness effects on pressure drop in single-phase flow in minichannels

NASA Astrophysics Data System (ADS)

Kandlikar, Satish G.; Schmitt, Derek; Carrano, Andres L.; Taylor, James B.

2005-10-01

Roughness features on the walls of a channel wall affect the pressure drop of a fluid flowing through that channel. This roughness effect can be described by (i) flow area constriction and (ii) increase in the wall shear stress. Replotting the Moody's friction factor chart with the constricted flow diameter results in a simplified plot and yields a single asymptotic value of friction factor for relative roughness values of ɛ /D>0.03 in the fully developed turbulent region. After reviewing the literature, three new roughness parameters are proposed (maximum profile peak height Rp, mean spacing of profile irregularities RSm, and floor distance to mean line Fp). Three additional parameters are presented to consider the localized hydraulic diameter variation (maximum, minimum, and average) in future work. The roughness ɛ is then defined as Rp+Fp. This definition yields the same value of roughness as obtained from the sand-grain roughness [H. Darcy, Recherches Experimentales Relatives au Mouvement de L'Eau dans les Tuyaux (Mallet-Bachelier, Paris, France, 1857); J. T. Fanning, A Practical Treatise on Hydraulic and Water Supply Engineering (Van Nostrand, New York, 1877, revised ed. 1886); J. Nikuradse, "Laws of flow in rough pipes" ["Stromungsgesetze in Rauen Rohren," VDI-Forschungsheft 361 (1933)]; Beilage zu "Forschung auf dem Gebiete des Ingenieurwesens," Ausgabe B Band 4, English translation NACA Tech. Mem. 1292 (1937)]. Specific experiments are conducted using parallel sawtooth ridge elements, placed normal to the flow direction, in aligned and offset configurations in a 10.03mm wide rectangular channel with variable gap (resulting hydraulic diameters of 325μm-1819μm with Reynolds numbers ranging from 200 to 7200 for air and 200 to 5700 for water). The use of constricted flow diameter extends the applicability of the laminar friction factor equations to relative roughness values (sawtooth height) up to 14%. In the turbulent region, the aligned and offset roughness arrangements yield different results indicating a need to further characterize the surface features. The laminar to turbulent transition is also seen to occur at lower Reynolds numbers with an increase in the relative roughness.

Origin of Parietal Podocytes in Atubular Glomeruli Mapped by Lineage Tracing

PubMed Central

Schulte, Kevin; Berger, Katja; Boor, Peter; Jirak, Peggy; Gelman, Irwin H.; Arkill, Kenton P.; Neal, Christopher R.; Kriz, Wilhelm; Floege, Jürgen; Smeets, Bart

2014-01-01

Parietal podocytes are fully differentiated podocytes lining Bowman’s capsule where normally only parietal epithelial cells (PECs) are found. Parietal podocytes form throughout life and are regularly observed in human biopsies, particularly in atubular glomeruli of diseased kidneys; however, the origin of parietal podocytes is unresolved. To assess the capacity of PECs to transdifferentiate into parietal podocytes, we developed and characterized a novel method for creating atubular glomeruli by electrocoagulation of the renal cortex in mice. Electrocoagulation produced multiple atubular glomeruli containing PECs as well as parietal podocytes that projected from the vascular pole and lined Bowman’s capsule. Notably, induction of cell death was evident in some PECs. In contrast, Bowman’s capsules of control animals and normal glomeruli of electrocoagulated kidneys rarely contained podocytes. PECs and podocytes were traced by inducible and irreversible genetic tagging using triple transgenic mice (PEC- or Pod-rtTA/LC1/R26R). Examination of serial cryosections indicated that visceral podocytes migrated onto Bowman’s capsule via the vascular stalk; direct transdifferentiation from PECs to podocytes was not observed. Similar results were obtained in a unilateral ureter obstruction model and in human diseased kidney biopsies, in which overlap of PEC- or podocyte-specific antibody staining indicative of gradual differentiation did not occur. These results suggest that induction of atubular glomeruli leads to ablation of PECs and subsequent migration of visceral podocytes onto Bowman’s capsule, rather than transdifferentiation from PECs to parietal podocytes. PMID:24071005

Social-Communicative Effects of the Picture Exchange Communication System (PECS) in Autism Spectrum Disorders

ERIC Educational Resources Information Center

Lerna, Anna; Esposito, Dalila; Conson, Massimiliano; Russo, Luigi; Massagli, Angelo

2012-01-01

Background: The Picture Exchange Communication System (PECS) is a common treatment choice for non-verbal children with autism. However, little empirical evidence is available on the usefulness of PECS in treating social-communication impairments in autism. Aims: To test the effects of PECS on social-communicative skills in children with autism,…

SGS Dynamics and Modeling near a Rough Wall.

NASA Astrophysics Data System (ADS)

Juneja, Anurag; Brasseur, James G.

1998-11-01

Large-eddy simulation (LES) of the atmospheric boundary layer (ABL) using classical subgrid-scale (SGS) models is known to poorly predict mean shear at the first few grid cells near the rough surface, creating error which can propogate vertically to infect the entire ABL. Our goal was to determine the first-order errors in predicted SGS terms that arise as a consequence of necessary under-resolution of integral scales and anisotropy which exist at the first few grid levels in LES of rough wall turbulence. Analyzing the terms predicted from eddy-viscosity and similarity closures with DNS anisotropic datasets of buoyancy- and shear-driven turbulence, we uncover three important issues which should be addressed in the design of SGS closures for rough walls and we provide a priori tests for the SGS model. Firstly, we identify a strong spurious coupling between the anisotropic structure of the resolved velocity field and predicted SGS dynamics which can create a feedback loop to incorrectly enhance certain components of the predicted resolved velocity. Secondly, we find that eddy viscosity and similarity SGS models do not contain enough degrees of freedom to capture, at a sufficient level of accuracy, both RS-SGS energy flux and SGS-RS dynamics. Thirdly, to correctly capture pressure transport near a wall, closures must be made more flexible to accommodate proper partitioning between SGS stress divergence and SGS pressure gradient.

CHARACTERIZATION OF EXTRAINTESTINAL PATHOGENIC ESCHERICHIA COLI FROM MEAT IN SOUTHERN THAILAND.

PubMed

Sukkua, Kannika; Pomwised, Rattanaruji; Rattanachuay, Pattamarat; Khianngam, Saowapar; Sukhumungoon, Pharanai

2017-01-01

Extraintestinal pathogenic Escherichia coli (ExPEC) is an E. coli group, which causes diseases in systems outside human intestinal tract. ExPEC isolates were recovered from fresh chicken (25%) and pork (10%) meats, but not beef and shrimp, from markets in southern Thailand. Among the 14 ExPEC strains isolated, all carried iutA and fimH, coding for aerobactin and type 1 fimbriae, respectively. Two ExPEC strains from chicken meat possessed kpsMTK1 coding for K1 capsular antigen, responsible for neonatal meningitis. Antimicrobial susceptibility assay revealed that all ExPEC were resistant to streptomycin and carried blaTEM, but susceptible to imipenem. Phylogenetic group analysis showed that 4, 4, and 6 ExPEC strains belonged to group A, B1 and D, respectively. ExPEC strains were classified into four serotypes, namely, O8 (2 strains), O15 (2 strains), O25 (1 strain), and O127a (1 strain), with the remaining untypeable. DNA profiling analysis by BOX-PCR revealed clonality of strains with the same serotype. The existence of ExPEC in meat products should cause concern regarding food safety and public health not only in southern Thailand but also throughout the country.

Effects of roughness on density-weighted particle statistics in turbulent channel flows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Milici, Barbara

2015-12-31

The distribution of inertial particles in turbulent flows is strongly influenced by the characteristics of the coherent turbulent structures which develop in the carrier flow field. In wall-bounded flows, these turbulent structures, which control the turbulent regeneration cycles, are strongly affected by the roughness of the wall, nevertheless its effects on the particle transport in two-phase turbulent flows has been still poorly investigated. The issue is discussed here by addressing DNS combined with LPT to obtain statistics of velocity and preferential accumulation of a dilute dispersion of heavy particles in a turbulent channel flow, bounded by irregular two-dimensional rough surfaces,more » in the one-way coupling regime.« less

General Characterization Methods for Photoelectrochemical Cells for Solar Water Splitting.

PubMed

Shi, Xinjian; Cai, Lili; Ma, Ming; Zheng, Xiaolin; Park, Jong Hyeok

2015-10-12

Photoelectrochemical (PEC) water splitting is a very promising technology that converts water into clean hydrogen fuel and oxygen by using solar light. However, the characterization methods for PEC cells are diverse and a systematic introduction to characterization methods for PEC cells has rarely been attempted. Unlike most other review articles that focus mainly on the material used for the working electrodes of PEC cells, this review introduces general characterization methods for PEC cells, including their basic configurations and methods for characterizing their performance under various conditions, regardless of the materials used. Detailed experimental operation procedures with theoretical information are provided for each characterization method. The PEC research area is rapidly expanding and more researchers are beginning to devote themselves to related work. Therefore, the content of this Minireview can provide entry-level knowledge to beginners in the area of PEC, which might accelerate progress in this area. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nondestructive evaluation of mechanically stabilized earth walls with frequency-modulated continuous wave (FM-CW) radar.

DOT National Transportation Integrated Search

2014-06-01

Effective techniques for a nondestructive evaluation of mechanically stabilized earth (MSE) walls during normal operation : or immediately after an earthquake event are yet to be developed. MSE walls often have a rough surface finishing for the : pur...

Studies on stability of PEC cells formed with CdS:Al films

NASA Astrophysics Data System (ADS)

Lokhande, C. D.; Pawar, S. H.

1984-02-01

Aluminum doped and undoped CdS films are deposited on stainless steel substrates by chemical bath deposition technique and are employed in PEC cells. The effects of heat treatment to photoanode and addition of salts like KCl and NaCl in an electrolyte on the stability of the PEC cells are studied. It is found that though the PEC cells formed with CdS films are stable in NaOH-Na 2S-S electrolyte, the stability of PEC cells formed with Al doped CdS films is achieved only after the addition of saturated salts in the electrolyte.

A Generalized Wall Function

NASA Technical Reports Server (NTRS)

Shih, Tsan-Hsing; Povinelli, Louis A.; Liu, Nan-Suey; Potapczuk, Mark G.; Lumley, J. L.

1999-01-01

The asymptotic solutions, described by Tennekes and Lumley (1972), for surface flows in a channel, pipe or boundary layer at large Reynolds numbers are revisited. These solutions can be extended to more complex flows such as the flows with various pressure gradients, zero wall stress and rough surfaces, etc. In computational fluid dynamics (CFD), these solutions can be used as the boundary conditions to bridge the near-wall region of turbulent flows so that there is no need to have the fine grids near the wall unless the near-wall flow structures are required to resolve. These solutions are referred to as the wall functions. Furthermore, a generalized and unified law of the wall which is valid for whole surface layer (including viscous sublayer, buffer layer and inertial sublayer) is analytically constructed. The generalized law of the wall shows that the effect of both adverse and favorable pressure gradients on the surface flow is very significant. Such as unified wall function will be useful not only in deriving analytic expressions for surface flow properties but also bringing a great convenience for CFD methods to place accurate boundary conditions at any location away from the wall. The extended wall functions introduced in this paper can be used for complex flows with acceleration, deceleration, separation, recirculation and rough surfaces.

Wall-slip of highly filled powder injection molding compounds: Effect of flow channel geometry and roughness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hausnerova, Berenika; Sanetrnik, Daniel; Paravanova, Gordana

2014-05-15

The paper deals with the rheological behavior of highly filled compounds proceeded via powder injection molding (PIM) and applied in many sectors of industry (automotive, medicine, electronic or military). Online rheometer equipped with slit dies varying in surface roughness and dimensions was applied to investigate the wall-slip as a rheological phenomenon, which can be considered as a parameter indicating the separation of compound components (polymer binder and metallic powder) during high shear rates when injection molded.

Wall-slip of highly filled powder injection molding compounds: Effect of flow channel geometry and roughness

NASA Astrophysics Data System (ADS)

Hausnerova, Berenika; Sanetrnik, Daniel; Paravanova, Gordana

2014-05-01

The paper deals with the rheological behavior of highly filled compounds proceeded via powder injection molding (PIM) and applied in many sectors of industry (automotive, medicine, electronic or military). Online rheometer equipped with slit dies varying in surface roughness and dimensions was applied to investigate the wall-slip as a rheological phenomenon, which can be considered as a parameter indicating the separation of compound components (polymer binder and metallic powder) during high shear rates when injection molded.

Advantages and disadvantages of graduated and inverse graduated compression hosiery in patients with chronic venous insufficiency and healthy volunteers: A prospective, mono-centric, blinded, open randomised, controlled and cross-over trial.

PubMed

Riebe, Helene; Konschake, Wolfgang; Haase, Hermann; Jünger, Michael

2018-02-01

Background The therapeutic effectiveness of compression therapy depends on the selection of compression hosiery. Objectives To assess efficacy and tolerability of graduated elastic compression stockings (GECS) and inverse graduated elastic compression stockings (PECS). Methods Thirty-two healthy volunteers and thirty-two patients with chronic venous insufficiency were analysed; wear period: one week for each stocking type (randomised, blinded). volume reduction of 'Lower leg' (Image3D®) and 'Distal leg and foot' (water plethysmography). clinical symptoms of chronic venous insufficiency assessed by the Venous Clinical Severity Score, side effects and wear comfort in both groups. Results Volume of 'Lower leg': significant reduction in healthy volunteers (mean GECS: -37.5 mL, mean PECS: -37.2 mL) and in patients (mean GECS: -55.6 mL, mean PECS: -41.6 mL). Volume of 'Distal lower leg and foot': significant reduction in healthy volunteers (mean GECS: -27 mL, mean PECS: -16.7 mL), significant reduction in patients by GECS (mean: -43.4 mL), but non-significant reduction by PECS (mean: -22.6 mL). Clinical symptoms of chronic venous insufficiency were improved significantly better with GECS than with PECS, p < 0.001. GECS led to more painful constrictions, p = 0.047, PECS slipped down more often, p < 0.001. Conclusion GECS and PECS reduce volume of the segment 'Lower leg' in patients and healthy volunteers. Patients' volume of the 'Distal lower leg and foot', however, were diminished significantly only by GECS ( p = 0.0001). Patients' complaints were improved by both GECS and PECS, and GECS were superior to PECS.

Some Activities of MISSE 6 Mission

NASA Technical Reports Server (NTRS)

Prasad, Narasimha S.

2009-01-01

The objective of the Materials International Space Station Experiment (MISSE) is to study the performance of novel materials when subjected to the synergistic effects of the harsh space environment for several months. In this paper, a few laser and optical elements from NASA Langley Research Center (LaRC) that have been flown on MISSE 6 mission will be discussed. These items were characterized and packed inside a ruggedized Passive Experiment Container (PEC) that resembles a suitcase. The PEC was tested for survivability due to launch conditions. Subsequently, the MISSE 6 PEC was transported by the STS-123 mission to International Space Station (ISS) on March 11, 2008. The astronauts successfully attached the PEC to external handrails and opened the PEC for long term exposure to the space environment. The plan is to retrieve the MISSE 6 PEC by STS-128 mission in August 2009.

The interaction of pulsed eddy current with metal surface crack for various coils

NASA Astrophysics Data System (ADS)

Yang, Hung-Chi; Tai, Cheng-Chi

2002-05-01

We study the interaction of pulsed eddy current (PEC) with metal surface cracks using various coils that have different geometric sizes. In the previous work, we have showed that the PEC technique can be used to inspect electrical-discharge-machined (EDM) notches with depth from 0.5 mm to 9 mm. The results showed that the relationship between PEC signals and crack depth is obvious. In this work, we further try a series of coils with different radii, heights, turns and shapes. We will discuss the effects of these coil parameters on the PEC signal. Some other critical problems of PEC measurements such as signal drift that caused by heating effect of coil currents will be studied. We also show more experiments on fatigue cracks to demonstrate the capability of PEC technique for cracks inspection.

The effects of PECS teaching to Phase III on the communicative interactions between children with autism and their teachers.

PubMed

Carr, Deborah; Felce, Janet

2007-04-01

The study investigated the impact of mastery of the Picture Exchange Communication System (PECS) to Phase III, on the communications of children with autism. Children aged between 3 and 7 years, formed a PECS intervention group and a non-intervention control group. The intervention group received 15 h of PECS teaching over 5 weeks. Three 2-h classroom observations recorded communications between the children and their teachers. These occurred: 6 weeks before teaching; during the week immediately prior to teaching; during the week immediately following teaching. For the control group, two 2-h observations were separated by a 5-week interval without PECS teaching. Communicative initiations and dyadic interactions increased significantly between the children and teachers in the PECS group but not for the control group.

Evaluation of pharmaceuticals in surface water: reliability of PECs compared to MECs.

PubMed

Celle-Jeanton, Hélène; Schemberg, Dimitri; Mohammed, Nabaz; Huneau, Frédéric; Bertrand, Guillaume; Lavastre, Véronique; Le Coustumer, Philippe

2014-12-01

Due to the current analytical processes that are not able to measure all the pharmaceutical molecules and to the high costs and the consumption of time to sample and analyze PhACs, models to calculate Predicted Environmental Concentrations (PECs) have been developed. However a comparison between MECs and PECs, taking into account the methods of calculations and peculiarly the parameters included in the calculation (consumption data, pharmacokinetic parameters, elimination rate in STPs and in the environment), is necessary to assess the validity of PECs. MEC variations of sixteen target PhACs [acetaminophen (ACE), amlodipine (AML), atenolol (ATE), caffeine (CAF), carbamazepine (CAR), doxycycline (DOX), epoxycarbamazepine (EPO), fluvoxamine (FLU), furosemide (FUR), hydrochlorothiazide (HYD), ifosfamide (IFO), losartan (LOS), pravastatin (PRA), progesterone (PROG), ramipril (RAM), trimetazidine (TRI)] have been evaluated during one hydrological cycle, from October 2011 to October 2012 and compared to PECs calculated by using an adaptation of the models proposed by Heberer and Feldmann (2005) and EMEA (2006). Comparison of PECs and MECS has been achieved for six molecules: ATE, CAR, DOX, FUR, HYD and PRA. DOX, FUR and HYD present differences between PECs and MECs on an annual basis but their temporal evolutions follow the same trends. PEC evaluation for these PhACs could then be possible but need some adjustments of consumption patterns, pharmacokinetic parameters and/or mechanisms of (bio)degradation. ATE, CAR and PRA are well modeled; PECs can then be used as reliable estimation of concentrations without any reserve. Copyright © 2014 Elsevier Ltd. All rights reserved.

Biomimetic microbeads containing a chondroitin sulfate/chitosan polyelectrolyte complex for cell-based cartilage therapy.

PubMed

Daley, Ethan Lh; Coleman, Rhima M; Stegemann, Jan P

2015-10-28

Articular cartilage has a limited healing capacity that complicates the treatment of joint injuries and osteoarthritis. Newer repair strategies have focused on the use of cells and biomaterials to promote cartilage regeneration. In the present study, we developed and characterized bioinspired materials designed to mimic the composition of the cartilage extracellular matrix. Chondroitin sulfate (CS) and chitosan (CH) were used to form physically cross-linked macromolecular polyelectrolyte complexes (PEC) without the use of additional crosslinkers. A single-step water-in-oil emulsification process was used to either directly embed mesenchymal stem cells (MSC) in PEC particles created with a various concentrations of CS and CH, or to co-embed MSC with PEC in agarose-based microbeads. Direct embedding of MSC in PEC resulted in high cell viability but irregular and large particles. Co-embedding of PEC particles with MSC in agarose (Ag) resulted in uniform microbeads 80-90 μm in diameter that maintained high cell viability over three weeks in culture. Increased serum content resulted in more uniform PEC distribution within the microbead matrix, and both high and low CS:CH ratios resulted in more homogeneous microbeads than 1:1 formulations. Under chondrogenic conditions, expression of sulfated GAG and collagen type II was increased in 10:1 CS:CH PEC-Ag microbeads compared to pure Ag beads, indicating a chondrogenic influence of the PEC component. Such PEC-Ag microbeads may have utility in the directed differentiation and delivery of progenitor cell populations for cartilage repair.

The Effects of PECS Teaching to Phase III on the Communicative Interactions between Children with Autism and Their Teachers

ERIC Educational Resources Information Center

Carr, Deborah; Felce, Janet

2007-01-01

The study investigated the impact of mastery of the Picture Exchange Communication System (PECS) to Phase III, on the communications of children with autism. Children aged between 3 and 7 years, formed a PECS intervention group and a non-intervention control group. The intervention group received 15 h of PECS teaching over 5 weeks. Three 2-h…

The Effect of an Isogrid on Cryogenic Propellant Behavior and Thermal Stratification

NASA Technical Reports Server (NTRS)

Oliveira, Justin; Kirk, Daniel R.; Chintalapati, Sunil; Schallhorn, Paul A.; Piquero, Jorge L.; Campbell, Mike; Chase, Sukhdeep

2007-01-01

All models for thermal stratification available in the presentation are derived using smooth, flat plate laminar and turbulent boundary layer models. This study examines the effect of isogrid (roughness elements) on the surface of internal tank walls to mimic the effects of weight-saving isogrid, which is located on the inside of many rocket propellant tanks. Computational Fluid Dynamics (CFD) is used to study the momentum and thermal boundary layer thickness for free convection flows over a wall with generic roughness elements. This presentation makes no mention of actual isogrid sizes or of any specific tank geometry. The magnitude of thermal stratification is compared for smooth and isogrid-lined walls.

Chitosan/pectin/gum Arabic polyelectrolyte complex: process-dependent appearance, microstructure analysis and its application.

PubMed

Tsai, Ruei-Yi; Chen, Pin-Wen; Kuo, Ting-Yun; Lin, Che-Min; Wang, Da-Ming; Hsien, Tzu-Yang; Hsieh, Hsyue-Jen

2014-01-30

Novel chitosan/pectin/gum Arabic polyelectrolyte complex (PEC) solutions and membranes with various compositions were prepared for biomedical applications. The appearance of the PEC solutions, either clear or turbid, was process-dependent and depended on how the three components were dissolved and mixed. The addition of gum Arabic to the chitosan and pectin significantly decreased the viscosities of the resultant PEC solutions due to the formation of globe-like microstructures that was accompanied by network-like microstructures and other molecular entanglements. The mechanical strength and hydrophilicity of the PEC membranes manufactured from the PEC solutions, especially for a weight ratio of 84/8/8 (chitosan/pectin/gum Arabic), were enhanced compared to pure chitosan membranes. Moreover, the use of the 84/8/8 PEC membranes as a drug carrier exhibited steady and fairly complete release of a drug (insulin) for 6h. Based on these promising results, the chitosan/pectin/gum Arabic PEC membranes have great potential in controlled drug release applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

Meta-analysis of PECS with individuals with ASD: investigation of targeted versus non-targeted outcomes, participant characteristics, and implementation phase.

PubMed

Ganz, Jennifer B; Davis, John L; Lund, Emily M; Goodwyn, Fara D; Simpson, Richard L

2012-01-01

The Picture Exchange Communication System (PECS) is a widely used picture/icon aided augmentative communication system designed for learners with autism and other developmental disorders. This meta-analysis analyzes the extant empirical literature for PECS relative to targeted (functional communication) and non-targeted concomitant outcomes (behavior, social skills, and speech) for learners with autism, learners with autism and intellectual disabilities and those with autism and multiple disabilities. Effect size analyses were done using the Improvement Rate Difference method, an advanced metric. Effect sizes were independently analyzed for targeted and non-targeted outcomes, student age, learner disability, and number of phases in the PECS protocol acquired by learners. Results supported the judgment that PECS is a promising intervention method. Analysis also revealed that functional communication outcomes associated with the PECS protocol were most impacted, that preschool children and those with autism generally showed the strongest training effects, and that in general students who advanced through the most PECS protocol phases had the best outcomes. Copyright © 2011 Elsevier Ltd. All rights reserved.

Investigating the Acquisition, Generalization, and Emergence of Untrained Verbal Operants for Mands Acquired Using the Picture Exchange Communication System in Adults With Severe Developmental Disabilities

PubMed Central

Ziomek, Megan M; Rehfeldt, Ruth Anne

2008-01-01

This study compared the total amount of training time and total number of trial blocks for individuals with severe developmental disabilities to acquire mands under control of unconditioned establishing operations and mands under control of transitive conditioned establishing operations for manual sign and for the Picture Exchange Communication System (PECS). Also examined was the generalization of mands across settings and communicative partners, as well as the emergence of untrained tacts and intraverbals for mands acquired using PECS. Mands for preferred items and for items needed to complete a chained task were acquired more rapidly and in fewer training blocks for PECS than for manual sign. Moreover, mands established using PECS generalized across settings and communicative partners. Finally, untrained tacts and intraverbals using PECS were shown to emerge for some of the participants following PECS training. These results suggest that PECS may be a viable alternative communication system for adults with severe developmental disabilities who have little or no history of systematic instruction and limited imitative repertoires. PMID:22477401

Investigating the acquisition, generalization, and emergence of untrained verbal operants for mands acquired using the picture exchange communication system in adults with severe developmental disabilities.

PubMed

Ziomek, Megan M; Rehfeldt, Ruth Anne

2008-01-01

This study compared the total amount of training time and total number of trial blocks for individuals with severe developmental disabilities to acquire mands under control of unconditioned establishing operations and mands under control of transitive conditioned establishing operations for manual sign and for the Picture Exchange Communication System (PECS). Also examined was the generalization of mands across settings and communicative partners, as well as the emergence of untrained tacts and intraverbals for mands acquired using PECS. Mands for preferred items and for items needed to complete a chained task were acquired more rapidly and in fewer training blocks for PECS than for manual sign. Moreover, mands established using PECS generalized across settings and communicative partners. Finally, untrained tacts and intraverbals using PECS were shown to emerge for some of the participants following PECS training. These results suggest that PECS may be a viable alternative communication system for adults with severe developmental disabilities who have little or no history of systematic instruction and limited imitative repertoires.

Effect of doping (C or N) and co-doping (C+N) on the photoactive properties of magnetron sputtered titania coatings for the application of solar water-splitting.

PubMed

Rahman, M; Dang, B H Q; McDonnell, K; MacElroy, J M D; Dowling, D P

2012-06-01

The photocatalytic splitting of water into hydrogen and oxygen using a photoelectrochemical (PEC) cell containing titanium dioxide (TiO2) photoanode is a potentially renewable source of chemical fuels. However, the size of the band gap (-3.2 eV) of the TiO2 photocatalyst leads to its relatively low photoactivity toward visible light in a PEC cell. The development of materials with smaller band gaps of approximately 2.4 eV is therefore necessary to operate PEC cells efficiently. This study investigates the effect of dopant (C or N) and co-dopant (C+N) on the physical, structural and photoactivity of TiO2 nano thick coating. TiO2 nano-thick coatings were deposited using a closed field DC reactive magnetron sputtering technique, from titanium target in argon plasma with trace addition of oxygen. In order to study the influence of doping such as C, N and C+N inclusions in the TiO2 coatings, trace levels of CO2 or N2 or CO2+N2 gas were introduced into the deposition chamber respectively. The properties of the deposited nano-coatings were determined using Spectroscopic Ellipsometry, SEM, AFM, Optical profilometry, XPS, Raman, X-ray diffraction UV-Vis spectroscopy and tri-electrode potentiostat measurements. Coating growth rate, structure, surface morphology and roughness were found to be significantly influenced by the types and amount of doping. Substitutional type of doping in all doped sample were confirmed by XPS. UV-vis measurement confirmed that doping (especially for C doped sample) facilitate photoactivity of sputtered deposited titania coating toward visible light by reducing bandgap. The photocurrent density (indirect indication of water splitting performance) of the C-doped photoanode was approximately 26% higher in comparison with un-doped photoanode. However, coating doped with nitrogen (N or N+C) does not exhibit good performance in the photoelectrochemical cell due to their higher charge recombination properties.

Fully Depleted Ti-Nb-Ta-Zr-O Nanotubes: Interfacial Charge Dynamics and Solar Hydrogen Production.

PubMed

Chiu, Yi-Hsuan; Lai, Ting-Hsuan; Chen, Chun-Yi; Hsieh, Ping-Yen; Ozasa, Kazunari; Niinomi, Mitsuo; Okada, Kiyoshi; Chang, Tso-Fu Mark; Matsushita, Nobuhiro; Sone, Masato; Hsu, Yung-Jung

2018-05-01

Poor kinetics of hole transportation at the electrode/electrolyte interface is regarded as a primary cause for the mediocre performance of n-type TiO 2 photoelectrodes. By adopting nanotubes as the electrode backbone, light absorption and carrier collection can be spatially decoupled, allowing n-type TiO 2 , with its short hole diffusion length, to maximize the use of the available photoexcited charge carriers during operation in photoelectrochemical (PEC) water splitting. Here, we presented a delicate electrochemical anodization process for the preparation of quaternary Ti-Nb-Ta-Zr-O mixed-oxide (denoted as TNTZO) nanotube arrays and demonstrated their utility in PEC water splitting. The charge-transfer dynamics for the electrodes was investigated using time-resolved photoluminescence, electrochemical impedance spectroscopy, and the decay of open-circuit voltage analysis. Data reveal that the superior photoactivity of TNTZO over pristine TiO 2 originated from the introduction of Nd, Ta, and Zr elements, which enhanced the amount of accessible charge carriers, modified the electronic structure, and improved the hole injection kinetics for expediting water splitting. By modulating the water content of the electrolyte employed in the anodization process, the wall thickness of the grown TNTZO nanotubes can be reduced to a size smaller than that of the depletion layer thickness, realizing a fully depleted state for charge carriers to further advance the PEC performance. Hydrogen evolution tests demonstrate the practical efficacy of TNTZO for realizing solar hydrogen production. Furthermore, with the composition complexity and fully depleted band structure, the present TNTZO nanotube arrays may offer a feasible and universal platform for the loading of other semiconductors to construct a sophisticated heterostructure photoelectrode paradigm, in which the photoexcited charge carriers can be entirely utilized for efficient solar-to-fuel conversion.

Effects of vertical wall and tetrapod weights on wave overtopping in rubble mound breakwaters under irregular wave conditions

NASA Astrophysics Data System (ADS)

Park, Sang Kil; Dodaran, Asgar Ahadpour; Han, Chong Soo; Shahmirzadi, Mohammad Ebrahim Meshkati

2014-12-01

Rubble mound breakwaters protect the coastal line against severe erosion caused by wave action. This study examined the performance of different sizes and properties (i.e. height of vertical wall and tetrapod size) of rubble mound breakwaters on reducing the overtopping discharge. The physical model used in this study was derived based on an actual rubble mound in Busan Yacht Harbor. This research attempts to fill the gap in practical knowledge on the combined effect of the armor roughness and vertical wall on wave overtopping in rubble mound breakwaters. The main governing parameters used in this study were the vertical wall height, variation of the tetrapod weights, initial water level elevation, and the volume of overtopping under constant wave properties. The experimental results showed that the roughness factor differed according to the tetrapod size. Furthermore, the overtopping discharge with no vertical wall was similar to that with relatively short vertical walls ( 1 γv = 1). Therefore, the experimental results highlight the importance of the height of the vertical wall in reducing overtopping discharge. Moreover, a large tetrapod size may allow coastal engineers to choose a shorter vertical wall to save cost, while obtaining better performance.

Thin film of polyelectrolyte complex nanoparticles for protein sensing

NASA Astrophysics Data System (ADS)

Talukdar, Hrishikesh; Kundu, Sarathi

2018-04-01

Polyelectrolyte complex nanoparticles (PEC NPs) are prepared using two polyelectrolytes poly(Na-4-styrene sulphonate) (PSS) and poly(diallyldimethylammoniumchloride) (PDADMAC) at a molar mixing ratio of n-/n+ ≈ 0.67 by consecutive centrifugation. PEC NPs formation is investigated through dynamic light scattering (DLS) and atomic force microscopy (AFM). Optical behaviors of PEC NPs in thin film confirmation are studied using UV-Vis and photoluminescence spectroscopy. Although absorption peaks of PSS occurs at the same position before and after the formation of PEC NPs but emission peaks are found at ≈ 278 and 305 nm whereas for pure PSS emission peaks exist at ≈ 295 and 365 nm. Hence, thin film of PEC NPs can be applied as very sensitive material for protein sensing since absorption of protein is occurred at ≈ 278 nm. Protein sensing behavior of such PEC NPs thin film is studied using photoluminescence spectroscopy.

Photoelectrochemical enzymatic biosensors.

PubMed

Zhao, Wei-Wei; Xu, Jing-Juan; Chen, Hong-Yuan

2017-06-15

Enzymatic biosensors have been valuable bioanalytical devices for analysis of diverse targets in disease diagnosis, biological and biomedical research, etc. Photoelectrochemical (PEC) bioanalysis is a recently emerged method that promptly becoming a subject of new research interests due to its attractive potential for future bioanalysis with high sensitivity and specificity. PEC enzymatic biosensors integrate the inherent sensitivities of PEC bioanalysis and the selectivity of enzymes and thus share their both advantages. Currently, PEC enzymatic biosensors have become a hot topic of significant research and the recent impetus has grown rapidly as demonstrated by increased research papers. Given the pace of advances in this area, this review will make a thorough discussion and survey on the fundamentals, sensing strategies, applications and the state of the art in PEC enzymatic biosensors, followed by future prospects based on our own opinions. We hope this work could provide an accessible introduction to PEC enzymatic biosensors for any scientist. Copyright © 2016 Elsevier B.V. All rights reserved.

Influence of Additional Leading-Edge Surface Roughness on Performances in Highly Loaded Compressor Cascade

NASA Astrophysics Data System (ADS)

Chen, Shaowen; Xu, Hao; Sun, Shijun; Zhang, Longxin; Wang, Songtao

2015-05-01

Experimental research has been carried out at low speed to investigate the effect of additional leading-edge surface roughness on a highly-loaded axial compressor cascade. A 5-hole aerodynamic probe has been traversed across one pitch to obtain the distribution of total pressure loss coefficient, secondary flow vector, flow angles and other aerodynamic parameters at the exit section. Meanwhile, ink-trace flow visualization has been used to measure the flow fields on the walls of cascades and a detailed topology structure of the flow on the walls has been obtained. Aerodynamic parameters and flow characteristics are compared by arranging different levels of roughness on various parts of the leading edge. The results show that adding surface roughness at the leading edge and on the suction side obviously influences cascade performance. Aggravated 3-D flow separation significantly increases the loss in cascades, and the loss increases till 60% when the level of emery paper is 80 mm. Even there is the potential to improve cascade performance in local area of cascade passage. The influence of the length of surface roughness on cascade performance is not always adverse, and which depends on the position of surface roughness.

Direct numerical simulation of flow over dissimilar, randomly distributed roughness elements: A systematic study on the effect of surface morphology on turbulence

NASA Astrophysics Data System (ADS)

Forooghi, Pourya; Stroh, Alexander; Schlatter, Philipp; Frohnapfel, Bettina

2018-04-01

Direct numerical simulations are used to investigate turbulent flow in rough channels, in which topographical parameters of the rough wall are systematically varied at a fixed friction Reynolds number of 500, based on a mean channel half-height h and friction velocity. The utilized roughness generation approach allows independent variation of moments of the surface height probability distribution function [thus root-mean-square (rms) surface height, skewness, and kurtosis], surface mean slope, and standard deviation of the roughness peak sizes. Particular attention is paid to the effect of the parameter Δ defined as the normalized height difference between the highest and lowest roughness peaks. This parameter is used to understand the trends of the investigated flow variables with departure from the idealized case where all roughness elements have the same height (Δ =0 ). All calculations are done in the fully rough regime and for surfaces with high slope (effective slope equal to 0.6-0.9). The rms roughness height is fixed for all cases at 0.045 h and the skewness and kurtosis of the surface height probability density function vary in the ranges -0.33 to 0.67 and 1.9 to 2.6, respectively. The goal of the paper is twofold: first, to investigate the possible effect of topographical parameters on the mean turbulent flow, Reynolds, and dispersive stresses particularly in the vicinity of the roughness crest, and second, to investigate the possibility of using the wall-normal turbulence intensity as a physical parameter for parametrization of the flow. Such a possibility, already suggested for regular roughness in the literature, is here extended to irregular roughness.

INTRODUCING THE FIRST EVER PEC WEBSITE

EPA Science Inventory

Since it's creation in 1985, the Pathogen Equivalency Committee (PEC) has been reviewing novel sludge disinfection technologies and their ability to protect human health and the environment. The PEC is charged to make recommendations on whether these novel technologies provide eq...

Effects of surface roughness on an adverse-pressure-gradient separating turbulent boundary layer

NASA Astrophysics Data System (ADS)

Wu, Wen; Piomelli, Ugo; Turbulence Simulation; Modelling Laboratory Team

2017-11-01

Separating turbulent boundary layers over smooth and rough flat plates are investigated by large-eddy simulations. A suction-blowing velocity distribution is imposed at the top boundary to produce an adverse-to-favourable pressure gradient and a closed separation bubble. Sandgrain roughness in the fully-rough regime is modelled by an immersed boundary method. In the rough-wall case, streamline detachment occurs earlier and the separation region is substantially larger due to the momentum deficit caused by the roughness. The adverse pressure gradient decreases the form drag and causes a thin reversed-flow region below the roughness crest, so that Cf = 0 does not coincide with the detachment of the flow from the surface. The wake regions behind roughness elements affect the intermittency of the near-wall flow, so that upstream of the detachment point the flow can be reversed half of the time, but its average is positive. The separated shear layer exhibits higher turbulent kinetic energy (TKE); the growth of the TKE there begins earlier relative to the separation point, and the peak TKE occurs close to the separation point. The momentum deficit caused by the roughness, again, plays a critical role in these changes. The authors acknowledge the support from Hydro-Québec and the NSERC Collaborative Research & Development program (CRDPJ 418786-11). The simulations were performed at CAC Queen't site. UP also thanks the support of Canada Research Chair Program.

The ABCG transporter PEC1/ABCG32 is required for the formation of the developing leaf cuticle in Arabidopsis.

PubMed

Fabre, Guillaume; Garroum, Imène; Mazurek, Sylwester; Daraspe, Jean; Mucciolo, Antonio; Sankar, Martial; Humbel, Bruno M; Nawrath, Christiane

2016-01-01

The cuticle is an essential diffusion barrier on aerial surfaces of land plants whose structural component is the polyester cutin. The PERMEABLE CUTICLE1/ABCG32 (PEC1) transporter is involved in plant cuticle formation in Arabidopsis. The gpat6 pec1 and gpat4 gapt8 pec1 double and triple mutants are characterized. Their PEC1-specific contributions to aliphatic cutin composition and cuticle formation during plant development are revealed by gas chromatography/mass spectrometry and Fourier-transform infrared spectroscopy. The composition of cutin changes during rosette leaf expansion in Arabidopsis. C16:0 monomers are in higher abundance in expanding than in fully expanded leaves. The atypical cutin monomer C18:2 dicarboxylic acid is more prominent in fully expanded leaves. Findings point to differences in the regulation of several pathways of cutin precursor synthesis. PEC1 plays an essential role during expansion of the rosette leaf cuticle. The reduction of C16 monomers in the pec1 mutant during leaf expansion is unlikely to cause permeability of the leaf cuticle because the gpat6 mutant with even fewer C16:0 monomers forms a functional rosette leaf cuticle at all stages of development. PEC1/ABCG32 transport activity affects cutin composition and cuticle structure in a specific and non-redundant fashion. © 2015 The Authors. New Phytologist © 2015 New Phytologist Trust.

Determination of wall shear stress from mean velocity and Reynolds shear stress profiles

NASA Astrophysics Data System (ADS)

Volino, Ralph J.; Schultz, Michael P.

2018-03-01

An analytical method is presented for determining the Reynolds shear stress profile in steady, two-dimensional wall-bounded flows using the mean streamwise velocity. The method is then utilized with experimental data to determine the local wall shear stress. The procedure is applicable to flows on smooth and rough surfaces with arbitrary pressure gradients. It is based on the streamwise component of the boundary layer momentum equation, which is transformed into inner coordinates. The method requires velocity profiles from at least two streamwise locations, but the formulation of the momentum equation reduces the dependence on streamwise gradients. The method is verified through application to laminar flow solutions and turbulent DNS results from both zero and nonzero pressure gradient boundary layers. With strong favorable pressure gradients, the method is shown to be accurate for finding the wall shear stress in cases where the Clauser fit technique loses accuracy. The method is then applied to experimental data from the literature from zero pressure gradient studies on smooth and rough walls, and favorable and adverse pressure gradient cases on smooth walls. Data from very near the wall are not required for determination of the wall shear stress. Wall friction velocities obtained using the present method agree with those determined in the original studies, typically to within 2%.

Current at domain walls, roughly speaking: nanoscales studies of disorder roughening and conduction

NASA Astrophysics Data System (ADS)

Paruch, Patrycja

2013-03-01

Domain walls in (multi)ferroic materials are the thin elastic interfaces separating regions with different orientations of magnetisation, electric polarisation, or spontaneous strain. Understanding their behaviour, and controlling domain size and stability, is key for their integration into applications, while fundamentally, domain walls provide an excellent model system in which the rich physics of disordered elastic interfaces can be accesses. In addition, domain walls can present novel properties, quite different from those of their parent materials, making them potentially useful as active components in future nano-devices. Here, we present our atomic force microscopy studies of ferroelectric domain walls in epitaxial Pb(Zr0.2Ti0.8)O3 and BiFeO3 thin films, in which we use piezorespose force microscopy to show unusual domain wall roughening behaviour, with very localised disorder regions in the sample leading to a complex, multi-affine scaling of the domain wall shape. We also show the effects of temperature, environmental conditions, and defects on switching dynamics and domain wall roughness. We combine these observations with parallel conductive-tip atomic force microscopy current measurements, which also show highly localised variations in conduction, and highlight the key role played by oxygen vacancies in the observed domain wall conduction.

Poly-Gaussian model of randomly rough surface in rarefied gas flow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aksenova, Olga A.; Khalidov, Iskander A.

2014-12-09

Surface roughness is simulated by the model of non-Gaussian random process. Our results for the scattering of rarefied gas atoms from a rough surface using modified approach to the DSMC calculation of rarefied gas flow near a rough surface are developed and generalized applying the poly-Gaussian model representing probability density as the mixture of Gaussian densities. The transformation of the scattering function due to the roughness is characterized by the roughness operator. Simulating rough surface of the walls by the poly-Gaussian random field expressed as integrated Wiener process, we derive a representation of the roughness operator that can be appliedmore » in numerical DSMC methods as well as in analytical investigations.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brull, S., E-mail: Stephane.Brull@math.u-bordeaux.fr; Charrier, P., E-mail: Pierre.Charrier@math.u-bordeaux.fr; Mieussens, L., E-mail: Luc.Mieussens@math.u-bordeaux.fr

It is well known that the roughness of the wall has an effect on microscale gas flows. This effect can be shown for large Knudsen numbers by using a numerical solution of the Boltzmann equation. However, when the wall is rough at a nanometric scale, it is necessary to use a very small mesh size which is much too expansive. An alternative approach is to incorporate the roughness effect in the scattering kernel of the boundary condition, such as the Maxwell-like kernel introduced by the authors in a previous paper. Here, we explain how this boundary condition can be implementedmore » in a discrete velocity approximation of the Boltzmann equation. Moreover, the influence of the roughness is shown by computing the structure scattering pattern of mono-energetic beams of the incident gas molecules. The effect of the angle of incidence of these molecules, of their mass, and of the morphology of the wall is investigated and discussed in a simplified two-dimensional configuration. The effect of the azimuthal angle of the incident beams is shown for a three-dimensional configuration. Finally, the case of non-elastic scattering is considered. All these results suggest that our approach is a promising way to incorporate enough physics of gas-surface interaction, at a reasonable computing cost, to improve kinetic simulations of micro- and nano-flows.« less

Towards predictive models for transitionally rough surfaces

NASA Astrophysics Data System (ADS)

Abderrahaman-Elena, Nabil; Garcia-Mayoral, Ricardo

2017-11-01

We analyze and model the previously presented decomposition for flow variables in DNS of turbulence over transitionally rough surfaces. The flow is decomposed into two contributions: one produced by the overlying turbulence, which has no footprint of the surface texture, and one induced by the roughness, which is essentially the time-averaged flow around the surface obstacles, but modulated in amplitude by the first component. The roughness-induced component closely resembles the laminar steady flow around the roughness elements at the same non-dimensional roughness size. For small - yet transitionally rough - textures, the roughness-free component is essentially the same as over a smooth wall. Based on these findings, we propose predictive models for the onset of the transitionally rough regime. Project supported by the Engineering and Physical Sciences Research Council (EPSRC).

Characteristics and psychosocial predictors of psychiatric emergency center transport and length of stay in patients with dementia and Alzheimer's disease: a preliminary report.

PubMed

Nejtek, Vicki A; Hardy, Sarah; Hall, James R; Winter, A Scott

2011-07-01

Agitation and aggression are common behaviors that often lead to psychiatric emergency center (PEC) admission of nursing home patients with dementia or Alzheimer's disease. However, few if any data are available that adequately describe characteristics and psychosocial triggers of agitation and aggression leading to transport and admission to a PEC. A preliminary investigation to explore all possible characteristics and psychosocial predictors of PEC transport and length of stay in men and women nursing home patients with dementia or Alzheimer's disease was designed. Frequency distributions, chi-square, analyses of variance, and regression analyses were used to analyze the data. One hundred PEC patient charts were reviewed, of which 58 charts were missing information and 42 charts provided evaluable data. Nursing homes located in impoverished areas transported patients to the PEC significantly more often than those in affluent areas. A disconnect between the agitated/aggressive mental state reported by nursing home staff leading to the PEC transport and the calm/cooperative mental status PEC clinicians observed during the admission process was evident. Data from the charts also showed that 74% of patients received off-label antipsychotics rather than FDA-approved medications to treat dementia or Alzheimer's disease. This is one of the few studies to identify characteristics and psychosocial triggers of PEC use and length of stay in nursing home patients. We also highlight potentially dangerous antipsychotic use in dementia and Alzheimer disease. Thus, our data add to the existing knowledge base regarding PEC utilization, length of stay, and pharmacotherapy in nursing home patients with dementia and Alzheimer's disease. Given the preliminary nature of this study, however, the results should be interpreted with caution.

Opioid-sparing effects of the thoracic interfascial plane blocks: A meta-analysis of randomized controlled trials.

PubMed

Singh, Preet Mohinder; Borle, Anuradha; Kaur, Manpreet; Trikha, Anjan; Sinha, Ashish

2018-01-01

Thoracic interfascial plane blocks and modification (PECS) have recently gained popularity for analgesic potential during breast surgery. We evaluate/consolidate the evidence on opioid-sparing effect of PECS blocks in comparison with conventional intravenous analgesia (IVA) and paravertebral block (PVB). Prospective, randomized controlled trials comparing PECS block to conventional IVA or PVB in patients undergoing breast surgery published till June 2017 were searched in the medical database. Comparisons were made for 24-h postoperative morphine consumption and intraoperative fentanyl-equivalent consumption. Final analysis included nine trials (PECS vs. IVA 4 trials and PECS vs. PVB 5 trials). PECS block showed a decreased intraoperative fentanyl consumption over IVA by 49.20 mcg (95% confidence interval [CI] =42.67-55.74) ( I 2 = 98.47%, P < 0.001) and PVB by 15.88 mcg (95% CI = 12.95-18.81) ( I 2 = 95.51%, P < 0.001). Postoperative, 24-h morphine consumption with PECS block was lower than IVA by 7.66 mg (95% CI being 6.23-9.10) ( I 2 = 63.15, P < 0.001) but was higher than PVB group by 1.26 mg (95% CI being 0.91-1.62) ( I 2 = 99.53%, P < 0.001). Two cases of pneumothorax were reported with PVB, and no complication was reported in any other group. Use of PECS block and its modifications with general anesthesia for breast surgery has significant opioid-sparing effect intraoperatively and during the first 24 h after surgery. It also has higher intraoperative opioid-sparing effect when compared to PVB. During the 1 st postoperative day, PVB has slightly more morphine sparing potential that may however be associated with higher complication rates. The present PECS block techniques show marked interstudy variations and need standardization.

[A monitor for the emergency psychiatric service chain].

PubMed

Salden, M E F H; van Kemenade, J F L M; van Dam, A; Mulder, C L

2014-01-01

Many organisations are involved in the delivery of psychiatric emergency care to patients in crisis. We therefore refer to these organisations as the Psychiatric Emergency Chain (PEC). The quality of the PEC determines the quality of the psychiatric emergency care in a region. In order to measure the quality of this type of care a monitor has been developed in collaboration with the main stakeholders in the region Western North Brabant (WNB). To develop a monitor to measure the quality of a PEC in a region, identify weak spots in the chain and feed back the results to the chain. By searching the literature, studying the primary process in the chain and by having interviews with stakeholders we compiled a questionnaire for monitoring the pec. The monitor was tested in the WNB region and adjusted on the basis of experiences with the respondents. Then the monitor was generalised and tested in another region (Eindhoven and the Kempen) in order to find out whether this instrument might also be applicable to other pecs in the Netherlands. The monitor provided the PEC with a common language for evaluating the chain. The monitor was able to pinpoint particular weak spots and collaboration problems such as the response time required to reach the emergency, communication between and within organisations and domain discussions between different stakeholders. Chain partners used the results of the monitor to negotiate better collaborative agreements and to improve their care. The monitor is able to pinpoint problem areas in the PEC and subsequently to generate feedback to its stakeholders. This creates opportunities for improvement in the PEC. Therefore the monitor is a useful instrument for evaluating a local PEC periodically.

Features of electrocoagulation syndrome after endoscopic submucosal dissection for colorectal neoplasm.

PubMed

Yamashina, Takeshi; Takeuchi, Yoji; Uedo, Noriya; Hamada, Kenta; Aoi, Kenji; Yamasaki, Yasushi; Matsuura, Noriko; Kanesaka, Takashi; Akasaka, Tomofumi; Yamamoto, Sachiko; Hanaoka, Noboru; Higashino, Koji; Ishihara, Ryu; Iishi, Hiroyasu

2016-03-01

Endoscopic submucosal dissection (ESD) is a promising treatment for large gastrointestinal superficial neoplasms, although it is technically difficult, and perforation and delayed bleeding are well-known adverse events. However, there have been no large studies about electrocoagulation syndrome after colorectal ESD. The aim of this study was to evaluate the incidence and clinical significant risk factors of post-ESD coagulation syndrome (PECS). This was a retrospective cohort study conducted in a referral cancer center. A total of 336 patients with colorectal neoplasms (143 adenomas or serrated lesions and 193 carcinomas) underwent ESD from January 2011 to June 2013. Incidence, outcome, and factors associated with occurrence of PECS were investigated. Occurred in 32 patients (9.5%). The median time until PECS was 15.5 h, and the median period of PECS was 32.5 h. Fever (≥37.6 °C) after ESD was found in 41% of the PECS group and 9% of the non-PECS group (P < 0.001). All PECS cases were managed conservatively. On multivariate analysis, female patients (odds ratio [OR] = 3.2, P = 0.002), lesion location at ascending colon and cecum (OR = 3.5, P = 0.001), and resected specimen ≥40 mm (OR = 2.1, P = 0.05) were independent risk factors for PECS. Occurred in 32 patients (9.5%) with colorectal ESD; however, all cases had a good outcome with conservative management. Female sex, tumor location at the ascending colon and cecum, and resected specimen ≥40 mm were independently significant risk factors for PECS. © 2015 Journal of Gastroenterology and Hepatology Foundation and John Wiley & Sons Australia, Ltd.

AN UPDATE ON TECHNOLOGIES SEEKING PFRP EQUIVALENCY

EPA Science Inventory

This presentation will: 1) Review the mandate of the Pathogen Equivalency Committee (PEC), 2) Review the PEC's current membership (of 10), 3) Discuss how a typical application is evaluated, 4) Note where information can be found by those interested in applying to the PEC, 5) List...

Biocompatible Polyelectrolyte Complex Nanoparticles from Lactoferrin and Pectin as Potential Vehicles for Antioxidative Curcumin.

PubMed

Yan, Jing-Kun; Qiu, Wen-Yi; Wang, Yao-Yao; Wu, Jian-Yong

2017-07-19

Polyelectrolyte complex nanoparticles (PEC NPs) were fabricated via electrostatic interactions between positively charged heat-denatured lactoferrin (LF) particles and negatively charged pectin. The obtained PEC NPs were then utilized as curcumin carriers. PEC NPs were prepared by mixing 1.0 mg/mL solutions of heat-denatured LF and pectin at a mass ratio of 1:1 (w/w) in the absence of NaCl at pH 4.50. PEC NPs that were prepared under optimized conditions were spherical in shape with a particle size of ∼208 nm and zeta potential of ∼-32 mV. Hydrophobic curcumin was successfully encapsulated into LF/pectin PEC NPs with high encapsulation efficiency (∼85.3%) and loading content (∼13.4%). The in vitro controlled release and prominent antioxidant activities of curcumin from LF/pectin PEC NPs were observed. The present work provides a facile and fast method to synthesize nanoscale food-grade delivery systems for the improved water solubility, controlled release, and antioxidant activity of hydrophobic curcumin.

"Brief report: increase in production of spoken words in some children with autism after PECS teaching to Phase III".

PubMed

Carr, Deborah; Felce, Janet

2007-04-01

The context for this work was an evaluation study [Carr, D., & Felce, J. A. (in press)] of the early phases of the Picture Exchange Communication System (PECS) [Frost, L. A., & Bondy, A. S. (1994). The picture exchange communication system training manual. Cherry Hill, NJ: Pyramid Educational Consultants, Inc.; Frost, L. A., & Bondy, A. S. (2004). The picture exchange communication system training manual, 2nd edn. Newark, DE: Pyramid Educational Consultants, Inc.]. This paper reports that five of 24 children who received 15 h of PECS teaching towards Phase III over a period of 4-5 weeks, showed concomitant increases in speech production, either in initiating communication with staff or in responding, or both. No children in the PECS group demonstrated a decrease in spoken words after receiving PECS teaching. In the control group, only one of 17 children demonstrated a minimal increase and four of 17 children demonstrated a decrease in use of spoken words after a similar period without PECS teaching.

Polyelectrolyte complexes of hTERT siRNA and polyethyleneimine: Effect of degree of PEG grafting on biological and cellular activity.

PubMed

Safari, Fatemeh; Tamaddon, Ali M; Zarghami, Nosratollah; Abolmali, S; Akbarzadeh, Abolfazl

2016-09-01

Gene silencing by siRNA (short interfering RNA)-targeted human telomerase reverse transcriptase (hTERT) is considered a successful strategy for cancer gene therapy. Polyelectrolyte complexes (PEC) of siRNA and cationic polymers such as polyethyleneimine (PEI) have been widely used for cellular transfection; however, they demonstrate some disadvantages such as cytotoxicity and extracellular matrix restrictions. PEG grafting technology was used in an attempt to improve the biocompatibility of PECs. Considering that this technology may compromise the cellular uptake of PECs, we aimed to study the effect of degree of PEI PEGylation on the carrier cytotoxicity, cellular association, and transfection efficiency of hTERT siRNA in the lung cancer cell line A549. Activated NHS ester of methoxy PEG-COOH 5 KDa was grafted to hyperbranched PEI 25 KDa in the molar ratios of 0.2 and 1. The copolymers were characterized by (1)H-NMR spectroscopy. PECs of PEI or PEG-g-PEI with siRNA, alone or co-incubated with heparin sulfate, were studied by the ethidium bromide exclusion assay. Cytotoxicity of the polymers (PEG-g-PEI vs PEI), alone and upon formation of PEC nanoparticles with hTERT siRNA, was determined by a validated MTT assay, in comparison to a scrambled control sequence, in A549 human lung carcinoma cells. The cellular uptake of the PECs of FITC-labeled siRNA was investigated by flow cytometry at different N/P ratios, and the silencing effect of the transfected siRNA was compared to that of the control sequence for different PECs by real time RT-PCR. The cytotoxicity of PEI decreased significantly by PEG grafting, even at a low degree of PEGylation. Moreover, the nonspecific cytotoxicity of PECs decreased by PEG grafting. PECs of PEG-g-PEI showed more biologic stability on incubation with heparin sulfate. Average particle size and zeta potential of PEC nanoparticles were diminished for those of PEG-g-PEI. The cellular association was more pronounced at an N/P ratio of 2.5 for PECs of PEI and PEG-g-PEI alike. The level of silencing of hTERT mRNA by PEC of PEG-g-PEI was sequence-dependent, and determined non-inferior when compared to the native PEI. Conclusively, the biocompatibility of PEI was improved by a low degree of PEGylation, with no adverse effect on the cellular uptake and the transfection activity. PEC nanoparticles of hTERT siRNA and PEG-g-PEI could act as a promising weapon against A549 cells, which has to be considered for an in vivo evaluation.

Passive emission colorimetric sensor (PECS) for measuring emission rates of formaldehyde based on an enzymatic reaction and reflectance photometry.

PubMed

Shinohara, Naohide; Kajiwara, Tomohisa; Ohnishi, Masato; Kodama, Kenichi; Yanagisawa, Yukio

2008-06-15

A coin-sized passive emission colorimetric sensor (PECS) based on an enzymatic reaction and a portable reflectance photometry device were developed to determine the emission rates of formaldehyde from building materials and other materials found indoors in only 30 minutes on-site. The color change of the PECS linearly correlated to the concentration of formaldehyde aqueous solutions up to 28 microg/mL. The correlation between the emission rates measured by using the PECS and those measured by using a desiccator method or by using a chamber method was fitted with a linear function and a power function, and the determination coefficients were more than 0.98. The reproducible results indicate that the emission rates could be obtained with the correlation equations from the data measured by using the PECS and the portable reflectance photometry device. Limits of detection (LODs) were 0.051 mg/L for the desiccator method and 3.1 microg/m2/h for the chamber method. Thus, it was confirmed that the emission rates of formaldehyde from the building materials classified as F four-star (< 0.3 mg/L (desiccator method) or < 5.0 microg/m2/h (chamber method)), based on Japanese Industrial Standards (JIS), could be measured with the PECS. The measurement with PECS was confirmed to be precise (RSD < 10%). Other chemicals emitted from indoor materials, such as methanol, ethanol, acetone, toluene, and xylene, interfered little with the measurement of formaldehyde emission rates by using the PECS.

Structural and biochemical characteristics of locomotory muscles of emperor penguins, Aptenodytes forsteri.

PubMed

Ponganis, P J; Costello, M L; Starke, L N; Mathieu-Costello, O; Kooyman, G L

1997-07-01

Structural and biochemical characteristics of the primary muscles used for swimming (pectoralis, PEC and supracoracoideus, SC) were compared to those of leg muscles in emperor penguins (Aptenodytes forsteri). The mass of PEC-SC was four times that of the leg musculature, and mitochondrial volume density in PEC and SC (4%) was two-thirds that in sartorius (S) and gastrocnemius. The differences in muscle mass and mitochondrial density yielded a 2.2-fold greater total mitochondrial content in PEC-SC than leg muscles, which appears to account for the 1.8-fold greater whole-body highest oxygen consumption previously recorded in emperor penguins during swimming compared to walking. Calculation of maximal mitochondrial O2 consumption in PEC-SC and leg muscle yielded value of 5.8-6.9 ml O2 ml-1 min-1, which are similar to those in locomotory muscles of most mammals and birds. A distinct feature of emperor penguin muscle was its myoglobin content, with concentrations in PEC-SC (6.4 g 100 g-1 among the highest measured in any species. This resulted in a PEC-SC O2 store greater than that of the entire blood. In addition, ratios of myoglobin content to mitochondrial volume density and to citrate synthase activity were 4.4 and 2.5 times greater in PEC than in S, indicative of the significant role of myoglobin in the adaptation of muscle to cardiovascular adjustments during diving.

The surface roughness effect on the performance of supersonic ejectors

NASA Astrophysics Data System (ADS)

Brezgin, D. V.; Aronson, K. E.; Mazzelli, F.; Milazzo, A.

2017-07-01

The paper presents the numerical simulation results of the surface roughness influence on gas-dynamic processes inside flow parts of a supersonic ejector. These simulations are performed using two commercial CFD solvers (Star- CCM+ and Fluent). The results are compared to each other and verified by a full-scale experiment in terms of global flow parameters (the entrainment ratio: the ratio between secondary to primary mass flow rate - ER hereafter) and local flow parameters distribution (the static pressure distribution along the mixing chamber and diffuser walls). A detailed comparative study of the employed methods and approaches in both CFD packages is carried out in order to estimate the roughness effect on the logarithmic law velocity distribution inside the boundary layer. Influence of the surface roughness is compared with the influence of the backpressure (static pressure at the ejector outlet). It has been found out that increasing either the ejector backpressure or the surface roughness height, the shock position displaces upstream. Moreover, the numerical simulation results of an ejector with rough walls in the both CFD solvers are well quantitatively agreed with each other in terms of the mean ER and well qualitatively agree in terms of the local flow parameters distribution. It is found out that in the case of exceeding the "critical roughness height" for the given boundary conditions and ejector's geometry, the ejector switches to the "off-design" mode and its performance decreases considerably.

Electromagnetic propagation in PEC and absorbing curved S-ducts

NASA Technical Reports Server (NTRS)

Baumeister, Kenneth J.

1988-01-01

A finite-element Galerkin formulation has been developed to study transverse magnetic (TM) wave propagation in 2-D S-curved ducts with both perfectly conducting and absorbing walls. The reflection and transmission at the entrances and the exits of the curved ducts are determined by coupling the finite-element solutions in the curved ducts to the eigenfunctions of an infinite, uniform, perfectly conducting duct. Example solutions are presented for a double mitred and S-ducts of various lengths. The length of the S-duct is found to significantly effect the reflective characteristics of the duct. Also, the effect of curvature on an absorbing duct is illustrated.

Getting Clever with the Sliding Ladder

ERIC Educational Resources Information Center

De, Subhranil

2014-01-01

The familiar system involving a uniform ladder sliding against a vertical wall and a horizontal floor is considered again. The floor is taken to be smooth and the wall to be possibly rough--a situation where no matter how large the static friction coefficient between the ladder and the wall, the ladder cannot lean at rest and must slide down.…

Numerical Simulation of Hypersonic Boundary Layer Receptivity, Transient Growth and Transition With Surface Roughness

DTIC Science & Technology

2009-12-31

of receptivity of the Mach 5.92 flow over a flat plate to two- dimensional wall perturbations with surface roughness: 1) amplitude...contain a significantly large intervalθ compared with the normal grid spacing h∆ , which may lead to a deterioration of accuracy of the method... of hypersonic boundary layer receptivity, transient growth and transition with surface roughness. The main approach is to use

Experimental Evaluation of the Training Structure of the Picture Exchange Communication System (PECS)

ERIC Educational Resources Information Center

Cummings, Anne R.; Carr, James E.; LeBlanc, Linda A.

2012-01-01

The Picture Exchange Communication System (PECS) is a picture-based alternative communication method that is widely accepted and utilized with individuals with disabilities. Although prior studies have examined the clinical efficacy of PECS, none have experimentally evaluated its manualized training structure. We experimentally evaluated the…

Impact of the picture exchange communication system: effects on communication and collateral effects on maladaptive behaviors.

PubMed

Ganz, Jennifer B; Parker, Richard; Benson, Joanne

2009-12-01

Many children with autism require intensive instruction in the use of augmentative or alternative communication systems, such as the Picture Exchange Communication System (PECS). This study investigated the use of PECS with three young boys with autism to determine the impact of PECS training on use of pictures for requesting, use of intelligible words, and maladaptive behaviors. A multiple baseline-probe design with a staggered start was implemented. Results indicated that all of the participants quickly learned to make requests using pictures and that two used intelligible speech following PECS instruction; maladaptive behaviors were variable throughout baseline and intervention phases. Although all of the participants improved in at least one dependent variable, there remain questions regarding who is best suited for PECS and similar interventions.

Effectiveness of the Picture Exchange Communication System (PECS) on communication and speech for children with autism spectrum disorders: a meta-analysis.

PubMed

Flippin, Michelle; Reszka, Stephanie; Watson, Linda R

2010-05-01

The Picture Exchange Communication System (PECS) is a popular communication-training program for young children with autism spectrum disorders (ASD). This meta-analysis reviews the current empirical evidence for PECS in affecting communication and speech outcomes for children with ASD. A systematic review of the literature on PECS written between 1994 and June 2009 was conducted. Quality of scientific rigor was assessed and used as an inclusion criterion in computation of effect sizes. Effect sizes were aggregated separately for single-subject and group studies for communication and speech outcomes. Eight single-subject experiments (18 participants) and 3 group studies (95 PECS participants, 65 in other intervention/control) were included. Results indicated that PECS is a promising but not yet established evidence-based intervention for facilitating communication in children with ASD ages 1-11 years. Small to moderate gains in communication were demonstrated following training. Gains in speech were small to negative. This meta-analysis synthesizes gains in communication and relative lack of gains made in speech across the PECS literature for children with ASD. Concerns about maintenance and generalization are identified. Emerging evidence of potential preintervention child characteristics is discussed. Phase IV was identified as a possibly influential program characteristic for speech outcomes.

Broiler chickens, broiler chicken meat, pigs and pork as sources of ExPEC related virulence genes and resistance in Escherichia coli isolates from community-dwelling humans and UTI patients.

PubMed

Jakobsen, Lotte; Spangholm, Daniel J; Pedersen, Karl; Jensen, Lars B; Emborg, Hanne-Dorthe; Agersø, Yvonne; Aarestrup, Frank M; Hammerum, Anette M; Frimodt-Møller, Niels

2010-08-15

Urinary tract infection (UTI) is one of the most common bacterial infections. UTI is primarily caused by extraintestinal pathogenic Escherichia coli (ExPEC) from the patients' own fecal flora. The ExPEC often belong to phylogroups B2 and D, the groups which include potent human ExPEC isolates causing UTI, bacteremia, and meningitis. The external sources of these ExPEC in the human intestine are unknown. The food supply may transmit ExPEC to humans. However, evidence of this hypothesis is limited. To assess this hypothesis, the objective of our study was to investigate the presence of ExPEC related virulence genes in E. coli isolates from UTI patients, community-dwelling humans, meat, and production animals. Accordingly, we included 964 geographically and temporally matched E. coli isolates from UTI patients (n=102), community-dwelling humans (n=109), fresh Danish (n=197) and imported broiler chicken meat (n=86), broiler chickens (n=138), fresh Danish (n=177) and imported pork (n=10), and pigs (n=145) in the study. All isolates were investigated for the presence of eight ExPEC related genes (kpsM II, papA, papC, iutA, sfaS, focG, afa, hlyD) using PCR. To investigate any similarities between isolates from the different origins, we performed a cluster analysis including antimicrobial resistance data previously published. We detected seven of the eight ExPEC related genes in isolates from broiler chicken meat, broiler chickens, pork and pigs. Our findings suggest that broiler chicken meat, broiler chickens, pork and pigs could be the source of strains with these ExPEC related virulence genes in community-dwelling humans and UTI patients. Especially detection of ExPEC related virulence genes in isolates belonging to phylogroups B2 and D is very concerning and may have a significant medical impact. The cluster analysis of virulence gene and antimicrobial resistance profiles showed strong similarities between UTI patient, community-dwelling human isolates, meat, and production animal isolates. Thus, these strains from meat and production animals may pose a zoonotic risk. Copyright 2010 Elsevier B.V. All rights reserved.

Sediment contamination of residential streams in the metropolitan kansas city area, USA: Part II. whole-sediment toxicity to the amphipod hyalella azteca

USGS Publications Warehouse

Tao, J.; Ingersoll, C.G.; Kemble, N.E.; Dias, J.R.; Murowchick, J.B.; Welker, G.; Huggins, D.

2010-01-01

This is the second part of a study that evaluates the influence of nonpoint sources on the sediment quality of five adjacent streams within the metropolitan Kansas City area, central United States. Physical, chemical, and toxicity data (Hyalella azteca 28-day whole-sediment toxicity test) for 29 samples collected in 2003 were used for this evaluation, and the potential causes for the toxic effects were explored. The sediments exhibited a low to moderate toxicity, with five samples identified as toxic to H. azteca. Metals did not likely cause the toxicity based on low concentrations of metals in the pore water and elevated concentrations of acid volatile sulfide in the sediments. Although individual polycyclic aromatic hydrocarbons (PAHs) frequently exceeded effect-based sediment quality guidelines [probable effect concentrations (PECs)], only four of the samples had a PEC quotient (PEC-Q) for total PAHs over 1.0 and only one of these four samples was identified as toxic. For the mean PEC-Q for organochlorine compounds (chlordane, dieldrin, sum DDEs), 4 of the 12 samples with a mean PEC-Q above 1.0 were toxic and 4 of the 8 samples with a mean PEC-Q above 3.0 were toxic. Additionally, four of eight samples were toxic, with a mean PEC-Q above 1.0 based on metals, PAHs, polychlorinated biphenyls (PCBs), and organochlorine pesticides. The increase in the incidence of toxicity with the increase in the mean PEC-Q based on organochlorine pesticides or based on metals, PAHs, PCBs, and organochlorine pesticides suggests that organochlorine pesticides might have contributed to the observed toxicity and that the use of a mean PEC-Q, rather than PEC-Qs for individual compounds, might be more informative in predicting toxic effects. Our study shows that stream sediments subject to predominant nonpoint sources contamination can be toxic and that many factors, including analysis of a full suite of PAHs and pesticides of both past and present urban applications and the origins of these organic compounds, are important to identify the causes of toxicity. ?? 2010 Springer Science+Business Media, LLC.

Enhancement in hydrogen evolution using Au-TiO2 hollow spheres with microbial devices modified with conjugated oligoelectrolytes

PubMed Central

Ngaw, Chee Keong; Wang, Victor Bochuan; Liu, Zhengyi; Zhou, Yi; Kjelleberg, Staffan; Zhang, Qichun; Tan, Timothy Thatt Yang; Loo, Say Chye Joachim

2015-01-01

Objective: Although photoelectrochemical (PEC) water splitting heralds the emergence of the hydrogen economy, the need for external bias and low efficiency stymies the widespread application of this technology. By coupling water splitting (in a PEC cell) to a microbial fuel cell (MFC) using Escherichia coli as the biocatalyst, this work aims to successfully demonstrate a sustainable hybrid PEC–MFC platform functioning solely by biocatalysis and solar energy, at zero bias. Through further chemical modification of the photo-anode (in the PEC cell) and biofilm (in the MFC), the performance of the hybrid system is expected to improve in terms of the photocurrent generated and hydrogen evolved. Methods: The hybrid system constitutes the interconnected PEC cell with the MFC. Both PEC cell and MFC are typical two-chambered systems housing the anode and cathode. Au-TiO2 hollow spheres and conjugated oligoelectrolytes were synthesised chemically and introduced to the PEC cell and MFC, respectively. Hydrogen evolution measurements were performed in triplicates. Results: The hybrid PEC–MFC platform generated a photocurrent density of 0.35 mA/cm2 (~70× enhancement) as compared with the stand-alone P25 standard PEC cell (0.005 mA/cm2) under one-sun illumination (100 mW/cm2) at zero bias (0 V vs. Pt). This increase in photocurrent density was accompanied by continuous H2 production. No H2 was observed in the P25 standard PEC cell whereas H2 evolution rate was ~3.4 μmol/h in the hybrid system. The remarkable performance is attributed to the chemical modification of E. coli through the incorporation of novel conjugated oligoelectrolytes in the MFC as well as the lower recombination rate and higher photoabsorption capabilities in the Au-TiO2 hollow spheres electrode. Conclusions: The combined strategy of photo-anode modification in PEC cells and chemically modified MFCs shows great promise for future exploitation of such synergistic effects between MFCs and semiconductor-based PEC water splitting. PMID:28721235

Reducing mTOR augments parietal epithelial cell density in a model of acute podocyte depletion and in aged kidneys

PubMed Central

McNicholas, Bairbre A.; Eng, Diana G.; Lichtnekert, Julia; Rabinowitz, Peter S.; Pippin, Jeffrey W.

2016-01-01

Parietal epithelial cell (PEC) response to glomerular injury may underlie a common pathway driving fibrogenesis following podocyte loss that typifies several glomerular disorders. Although the mammalian target of rapamycin (mTOR) pathway is important in cell homeostasis, little is known of the biological role or impact of reducing mTOR activity on PEC response following podocyte depletion, nor in the aging kidney. The purpose of these studies was to determine the impact on PECs of reducing mTOR activity following abrupt experimental depletion in podocyte number, as well as in a model of chronic podocyte loss and sclerosis associated with aging. Podocyte depletion was induced by an anti-podocyte antibody and rapamycin started at day 5 until death at day 14. Reducing mTOR did not lead to a greater reduction in podocyte density, despite greater glomerulosclerosis. However, mTOR inhibition lead to an increase in PEC density and PEC-derived crescent formation. Additionally, markers of epithelial-to-mesenchymal transition (platelet-derived growth factor receptor-β, α-smooth muscle actin, Notch-3) and PEC activation (CD44, collagen IV) were further increased by mTOR reduction. Aged mice treated with rapamycin for 1, 2, and 10 wk before death at 26.5 mo (≈75-yr-old human age) had increased the number of glomeruli with a crescentic appearance. mTOR inhibition at either a high or low level lead to changes in PEC phenotype, indicating PEC morphology is sensitive to changes mediated by global mTOR inhibition. PMID:27440779

Risk Factors of Post-Endoscopic Submucosal Dissection Electrocoagulation Syndrome for Colorectal Neoplasm.

PubMed

Ito, Sayo; Hotta, Kinichi; Imai, Kenichiro; Yamaguchi, Yuichiro; Kishida, Yoshihiro; Takizawa, Kohei; Kakushima, Naomi; Tanaka, Masaki; Kawata, Noboru; Yoshida, Masao; Ishiwatari, Hirotoshi; Matsubayashi, Hiroyuki; Ono, Hiroyuki

2018-06-04

Colorectal endoscopic submucosal dissection (ESD) is used for the treatment of large colorectal superficial neoplasms. However, there have been no large studies on electrocoagulation syndrome developing after colorectal ESD. The aim of this study was to clarify the incidence and clinical risk factors of post-ESD electrocoagulation syndrome (PECS). A total of 692 patients (median age, 70 years; 395 men) with 692 lesions, who underwent colorectal ESD at a tertiary cancer center between July 2010 and December 2015 were eligible. PECS was clinically diagnosed based on the presence of localized abdominal tenderness matching the ESD enforcement site, and fever (>37.5°C) or an inflammatory response (C-reactive protein level >0.5 mg/dL or leukocytosis >10000 cells/μL), without obvious findings of perforation, which developed at >6 h post-ESD. Outcomes of the procedure, the incidence of PECS, and risk factors associated with PECS were assessed. The incidence of PECS was 4.8% (33 patients), and all patients improved by conservative treatment. On multivariate analysis, the female sex (odds ratio [OR] 2.6; 95% confidence interval [95% CI], 1.2-5.7), tumor location at the cecum (OR 14.5; 95% CI: 3.7-53.7 vs rectum), and the presence of submucosal fibrosis (OR 2.8; 95% CI: 1.1-7.5) were found to be independent risk factors of PECS. This study identified the risk factors for PECS. Patients with high risk factors of PECS require careful management after colorectal ESD. This article is protected by copyright. All rights reserved.

Characterization of Polyelectrolyte Complex Formation Between Anionic and Cationic Poly(amino acids) and Their Potential Applications in pH-Dependent Drug Delivery.

PubMed

Folchman-Wagner, Zoë; Zaro, Jennica; Shen, Wei-Chiang

2017-06-30

Polyelectrolyte complexes (PECs) are self-assembling nano-sized constructs that offer several advantages over traditional nanoparticle carriers including controllable size, biodegradability, biocompatibility, and lack of toxicity, making them particularly appealing as tools for drug delivery. Here, we discuss potential application of PECs for drug delivery to the slightly acidic tumor microenvironment, a pH in the range of 6.5-7.0. Poly(l-glutamic acid) (E n ), poly(l-lysine) (K n ), and a copolymer composed of histidine-glutamic acid repeats ((HE) n ) were studied for their ability to form PECs, which were analyzed for size, polydispersity, and pH sensitivity. PECs showed concentration dependent size variation at residue lengths of E 51 /K 55 and E 135 /K 127 , however, no complexes were observed when E 22 or K 21 were used, even in combination with the longer chains. (HE) 20 /K 55 PECs could encapsulate daunomycin, were stable from pH 7.4-6.5, and dissociated completely between pH 6.5-6.0. Conversely, the E 51-dauno /K 55 PEC dissociated between pH 4.0 and 3.0. These values for pH-dependent particle dissociation are consistent with the p K a 's of the ionizable groups in each formulation and indicate that the specific pH-sensitivity of (HE) 20-dauno /K 55 PECs is mediated by incorporation of histidine. This response within a pH range that is physiologically relevant to the acidic tumors suggests a potential application of these PECs in pH-dependent drug delivery.

Sources, distribution and export coefficient of phosphorus in lowland polders of Lake Taihu Basin, China.

PubMed

Huang, Jiacong; Gao, Junfeng; Jiang, Yong; Yin, Hongbin; Amiri, Bahman Jabbarian

2017-12-01

Identifying phosphorus (P) sources, distribution and export from lowland polders is important for P pollution management, however, is challenging due to the high complexity of hydrological and P transport processes in lowland areas. In this study, the spatial pattern and temporal dynamics of P export coefficient (PEC) from all the 2539 polders in Lake Taihu Basin, China were estimated using a coupled P model for describing P dynamics in a polder system. The estimated amount of P export from polders in Lake Taihu Basin during 2013 was 1916.2 t/yr, with a spatially-averaged PEC of 1.8 kg/ha/yr. PEC had peak values (more than 4.0 kg/ha/yr) in the polders near/within the large cities, and was high during the rice-cropping season. Sensitivity analysis based on the coupled P model revealed that the sensitive factors controlling the PEC varied spatially and changed through time. Precipitation and air temperature were the most sensitive factors controlling PEC. Culvert controlling and fertilization were sensitive factors controlling PEC during some periods. This study demonstrated an estimation of PEC from 2539 polders in Lake Taihu Basin, and an identification of sensitive environmental factors affecting PEC. The investigation of polder P export in a watershed scale is helpful for water managers to learn the distribution of P sources, to identify key P sources, and thus to achieve best management practice in controlling P export from lowland areas. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enhanced Photoelectrocatalytic Decomplexation of Cu-EDTA and Cu Recovery by Persulfate Activated by UV and Cathodic Reduction.

PubMed

Zeng, Huabin; Liu, Shanshan; Chai, Buyu; Cao, Di; Wang, Yan; Zhao, Xu

2016-06-21

In order to enhance Cu-EDTA decomplexation and copper cathodic recovery via the photoelectrocatalytic (PEC) process, S2O8(2-) was introduced into the PEC system with a TiO2/Ti photoanode. At a current density of 0.2 mA/cm(2) and initial solution pH of 3.0, the decomplexation ratio of Cu complexes was increased from 47.5% in the PEC process to 98.4% with 5 mM S2O8(2-) addition into the PEC process (PEC/S2O8(2-)). Correspondently, recovery percentage of Cu was increased to 98.3% from 47.4% within 60 min. It was observed that nearly no copper recovery occurred within the initial reaction period of 10 min. Combined with the analysis of ESR and electrochemical LSV curves, it was concluded that activation of S2O8(2-) into SO4(·-) radicals by cathodic reduction occurred, which was prior to the reduction of liberated Cu(2+) ions. UV irradiation of S2O8(2-) also led to the production of SO4(·-). The generated SO4(·-) radicals enhanced the oxidation of Cu-EDTA. After the consumption of S2O8(2-), the Cu recovery via cathodic reduction proceeded quickly. Acidification induced by the transformation of SO4(·-) to OH· favored the copper cathodic recovery. The combined PEC/S2O8(2-) process was also efficient for the TOC removal from a real electroplating wastewater with the Cu recovery efficiency higher than 80%.

Mars Science Laboratory Heatshield Aerothermodynamics: Design and Reconstruction

NASA Technical Reports Server (NTRS)

Edquist, Karl T.; Hollis, Brian R.; Johnston, Christopher O.; Bose, Deepak; White, Todd R.; Mahzari, Milad

2013-01-01

The Mars Science Laboratory heatshield was designed to withstand a fully turbulent heat pulse based on test results and computational analysis on a pre-flight design trajectory. Instrumentation on the flight heatshield measured in-depth temperatures in the thermal protection system. The data indicate that boundary layer transition occurred at 5 of 7 thermocouple locations prior to peak heating. Data oscillations at 3 pressure measurement locations may also indicate transition. This paper presents the heatshield temperature and pressure data, possible explanations for the timing of boundary layer transition, and a qualitative comparison of reconstructed and computational heating on the as-flown trajectory. Boundary layer Reynolds numbers that are typically used to predict transition are compared to observed transition at various heatshield locations. A uniform smooth-wall transition Reynolds number does not explain the timing of boundary layer transition observed during flight. A roughness-based Reynolds number supports the possibility of transition due to discrete or distributed roughness elements on the heatshield. However, the distributed roughness height would have needed to be larger than the pre-flight assumption. The instrumentation confirmed the predicted location of maximum turbulent heat flux near the leeside shoulder. The reconstructed heat flux at that location is bounded by smooth-wall turbulent calculations on the reconstructed trajectory, indicating that augmentation due to surface roughness probably did not occur. Turbulent heating on the downstream side of the heatshield nose exceeded smooth-wall computations, indicating that roughness may have augmented heating. The stagnation region also experienced heating that exceeded computational levels, but shock layer radiation does not fully explain the differences.

Flow formed by spanwise gaps between roughness elements

NASA Technical Reports Server (NTRS)

Logan, E.; Lin, S. H.; Islam, O.

1985-01-01

Measurements of the three mean velocity components and the three Reynolds shear stresses were made in the region downstream of gaps between wall-mounted roughness elements of square cross section and high aspect ratio in a thick turbulent boundary layer. The effect of small and large gaps was studied in a wind tunnel at a Reynolds number of 3600, based on obstacle height and free-stream velocity. The small gap produces retardation of the gap flow as with a two-dimensional roughness element, but a definite interaction between gap and wake flows is observed. The interaction is more intense for the large gap than for the small. Both gaps generate a secondary crossflow which moves fluid away from the centerline in the wall region and toward the centerline in the outer (y greater than 1.5H) region.

The Picture Exchange Communication System (PECS): What Do the Data Say?

ERIC Educational Resources Information Center

Sulzer-Azaroff, Beth; Hoffman, Anne O.; Horton, Catherine B.; Bondy, Andrew; Frost, Lori

2009-01-01

Originally designed to enable young children with autism lacking functional communication to initiate requests and to describe what they observed, the Picture Exchange Communication System (PECS) has been the subject of an ever-expanding body of research and development. Thirty-four peer-reviewed published reports on PECS are analyzed in this…

Long-Term Effects of PECS on Social-Communicative Skills of Children with Autism Spectrum Disorders: A Follow-Up Study

ERIC Educational Resources Information Center

Lerna, Anna; Esposito, Dalila; Conson, Massimiliano; Massagli, Angelo

2014-01-01

Background: The Picture Exchange Communication System (PECS) is a popular augmentative communication system frequently used with "nonverbal" children with autism. Several studies suggested that PECS could represent an effective tool for promoting improvement of several social-communicative skills. Only sparse evidence is instead…

The Picture Exchange Communication System: Communicative Outcomes for Young Children with Disabilities.

ERIC Educational Resources Information Center

Schwartz, Ilene S.; Garfinkle, Ann N.; Bauer, Janet

1998-01-01

Presents two studies documenting the use of the Picture Exchange Communication System (PECS) for 31 preschool children with severe disabilities. Initial findings indicated the children could learn to use PECS quickly and efficiently. The second study, which included 18 participants, found that PECS use generalized to untrained settings. (Author/CR)

Understanding the Picture Exchange Communication System and Its Application in Physical Education

ERIC Educational Resources Information Center

Green, Amanda; Sandt, Dawn

2013-01-01

This article presents the Picture Exchange Communication System (PECS) and its applications in physical education. The PECS is an appropriate communication intervention for students with autism who lack functional communication skills. It is often confused with other visual support strategies, so the authors delineate the six phases of PECS and…

Influence of molecular weight of chemically sulfated citrus pectin fractions on their antithrombotic and bleeding effects.

PubMed

Cipriani, Thales R; Gracher, Ana Helena P; de Souza, Lauro M; Fonseca, Roberto J C; Belmiro, Celso L R; Gorin, Philip A J; Sassaki, Guilherme L; Iacomini, Marcello

2009-05-01

Evaluated were the anticoagulant and antithrombotic activities, and bleeding effect of two chemically sulfated polysaccharides, obtained from citric pectin, with different average molar masses. Both low-molecular-weight (Pec-LWS, 3,600 g/mol) and high-molecular-weight sulfated pectins (Pec-HWS, 12,000 g/mol) had essentially the same structure, consisting of a (1-->4)-linked alpha-D-GalpA chain with almost all its HO-2 and HO-3 groups substituted by sulfate. Both polysaccharides had anticoagulant activity in vitro, although Pec-HWS was a more potent antithrombotic agent in vivo, giving rise to total inhibition of venous thrombosis at a dose of 3.5 mg/kg body weight. Surprisingly, in contrast with heparin, Pec-HWS and Pec-LWS are able to directly inhibit alpha-thrombin and factor Xa by a mechanism independent of antithrombin (AT) and/or heparin co-factor II (HCII). Moreover, Pec-HWS provided a lower risk of bleeding than heparin at a dose of 100% effectiveness against venous thrombosis, indicating it to be a promising antithrombotic agent.

Ion-Conductive and Thermal Properties of a Synergistic Poly(ethylene carbonate)/Poly(trimethylene carbonate) Blend Electrolyte.

PubMed

Li, Zhenguang; Mogensen, Ronnie; Mindemark, Jonas; Bowden, Tim; Brandell, Daniel; Tominaga, Yoichi

2018-05-11

Electrolytes comprising poly(ethylene carbonate) (PEC)/poly(trimethylene carbonate) (PTM C) with lithium bis(trifluoromethane sulfonyl)imide (LiTFSI) are prepared by a simple solvent casting method. Although PEC and PTMC have similar chemical structures, they are immiscible and two glass transitions are present in the differential scanning calorimetry (DSC) measurements. Interestingly, these two polymers change to miscible blends with the addition of LiTFSI, and the ionic conductivity increases with increasing lithium salt concentration. The optimum composition of the blend electrolyte is achieved at PEC 6 PTMC 4 , with a conductivity as high as 10 -6 S cm -1 at 50 °C. This value is greater than that for single PEC- and PTMC-based electrolytes. Moreover, the thermal stability of the blend-based electrolytes is improved as compared to PEC-based electrolytes. It is clear that the interaction between CO groups and Li + gives rise to a compatible amorphous phase of PEC and PTMC. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Engineering MoSx/Ti/InP Hybrid Photocathode for Improved Solar Hydrogen Production

NASA Astrophysics Data System (ADS)

Li, Qiang; Zheng, Maojun; Zhong, Miao; Ma, Liguo; Wang, Faze; Ma, Li; Shen, Wenzhong

2016-07-01

Due to its direct band gap of ~1.35 eV, appropriate energy band-edge positions, and low surface-recombination velocity, p-type InP has attracted considerable attention as a promising photocathode material for solar hydrogen generation. However, challenges remain with p-type InP for achieving high and stable photoelectrochemical (PEC) performances. Here, we demonstrate that surface modifications of InP photocathodes with Ti thin layers and amorphous MoSx nanoparticles can remarkably improve their PEC performances. A high photocurrent density with an improved PEC onset potential is obtained. Electrochemical impedance analyses reveal that the largely improved PEC performance of MoSx/Ti/InP is attributed to the reduced charge-transfer resistance and the increased band bending at the MoSx/Ti/InP/electrolyte interface. In addition, the MoSx/Ti/InP photocathodes function stably for PEC water reduction under continuous light illumination over 2 h. Our study demonstrates an effective approach to develop high-PEC-performance InP photocathodes towards stable solar hydrogen production.

Engineering MoSx/Ti/InP Hybrid Photocathode for Improved Solar Hydrogen Production

PubMed Central

Li, Qiang; Zheng, Maojun; Zhong, Miao; Ma, Liguo; Wang, Faze; Ma, Li; Shen, Wenzhong

2016-01-01

Due to its direct band gap of ~1.35 eV, appropriate energy band-edge positions, and low surface-recombination velocity, p-type InP has attracted considerable attention as a promising photocathode material for solar hydrogen generation. However, challenges remain with p-type InP for achieving high and stable photoelectrochemical (PEC) performances. Here, we demonstrate that surface modifications of InP photocathodes with Ti thin layers and amorphous MoSx nanoparticles can remarkably improve their PEC performances. A high photocurrent density with an improved PEC onset potential is obtained. Electrochemical impedance analyses reveal that the largely improved PEC performance of MoSx/Ti/InP is attributed to the reduced charge-transfer resistance and the increased band bending at the MoSx/Ti/InP/electrolyte interface. In addition, the MoSx/Ti/InP photocathodes function stably for PEC water reduction under continuous light illumination over 2 h. Our study demonstrates an effective approach to develop high-PEC-performance InP photocathodes towards stable solar hydrogen production. PMID:27431993

Engineering MoSx/Ti/InP Hybrid Photocathode for Improved Solar Hydrogen Production.

PubMed

Li, Qiang; Zheng, Maojun; Zhong, Miao; Ma, Liguo; Wang, Faze; Ma, Li; Shen, Wenzhong

2016-07-19

Due to its direct band gap of ~1.35 eV, appropriate energy band-edge positions, and low surface-recombination velocity, p-type InP has attracted considerable attention as a promising photocathode material for solar hydrogen generation. However, challenges remain with p-type InP for achieving high and stable photoelectrochemical (PEC) performances. Here, we demonstrate that surface modifications of InP photocathodes with Ti thin layers and amorphous MoSx nanoparticles can remarkably improve their PEC performances. A high photocurrent density with an improved PEC onset potential is obtained. Electrochemical impedance analyses reveal that the largely improved PEC performance of MoSx/Ti/InP is attributed to the reduced charge-transfer resistance and the increased band bending at the MoSx/Ti/InP/electrolyte interface. In addition, the MoSx/Ti/InP photocathodes function stably for PEC water reduction under continuous light illumination over 2 h. Our study demonstrates an effective approach to develop high-PEC-performance InP photocathodes towards stable solar hydrogen production.

MISSE 6-Testing Materials in Space

NASA Technical Reports Server (NTRS)

Prasad, Narasimha S; Kinard, William H.

2008-01-01

The objective of the Materials International Space Station Experiment (MISSE) is to study the performance of novel materials when subjected to the synergistic effects of the harsh space environment by placing them in space environment for several months. In this paper, a few materials and components from NASA Langley Research Center (LaRC) that have been flown on MISSE 6 mission will be discussed. These include laser and optical elements for photonic devices. The pre-characterized MISSE 6 materials were packed inside a ruggedized Passive Experiment Container (PEC) that resembles a suitcase. The PEC was tested for survivability due to launch conditions. Subsequently, the MISSE 6 PEC was transported by the STS-123 mission to International Space Station (ISS) on March 11, 2008. The astronauts successfully attached the PEC to external handrails and opened the PEC for long term exposure to the space environment.

133. View of rock cut at base of rough ridge ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

133. View of rock cut at base of rough ridge and roadway crossing unnamed viaduct on Grandfather Mountain with the Great Wall of China supporting the curve in the distance. Looking southeast. - Blue Ridge Parkway, Between Shenandoah National Park & Great Smoky Mountains, Asheville, Buncombe County, NC

Opioid-sparing effects of the thoracic interfascial plane blocks: A meta-analysis of randomized controlled trials

PubMed Central

Singh, Preet Mohinder; Borle, Anuradha; Kaur, Manpreet; Trikha, Anjan; Sinha, Ashish

2018-01-01

Background: Thoracic interfascial plane blocks and modification (PECS) have recently gained popularity for analgesic potential during breast surgery. We evaluate/consolidate the evidence on opioid-sparing effect of PECS blocks in comparison with conventional intravenous analgesia (IVA) and paravertebral block (PVB). Materials and Methods: Prospective, randomized controlled trials comparing PECS block to conventional IVA or PVB in patients undergoing breast surgery published till June 2017 were searched in the medical database. Comparisons were made for 24-h postoperative morphine consumption and intraoperative fentanyl-equivalent consumption. Results: Final analysis included nine trials (PECS vs. IVA 4 trials and PECS vs. PVB 5 trials). PECS block showed a decreased intraoperative fentanyl consumption over IVA by 49.20 mcg (95% confidence interval [CI] =42.67–55.74) (I2 = 98.47%, P < 0.001) and PVB by 15.88 mcg (95% CI = 12.95–18.81) (I2 = 95.51%, P < 0.001). Postoperative, 24-h morphine consumption with PECS block was lower than IVA by 7.66 mg (95% CI being 6.23–9.10) (I2 = 63.15, P < 0.001) but was higher than PVB group by 1.26 mg (95% CI being 0.91–1.62) (I2 = 99.53%, P < 0.001). Two cases of pneumothorax were reported with PVB, and no complication was reported in any other group. Conclusions: Use of PECS block and its modifications with general anesthesia for breast surgery has significant opioid-sparing effect intraoperatively and during the first 24 h after surgery. It also has higher intraoperative opioid-sparing effect when compared to PVB. During the 1st postoperative day, PVB has slightly more morphine sparing potential that may however be associated with higher complication rates. The present PECS block techniques show marked interstudy variations and need standardization. PMID:29416465

Regular physical education class enhances sociality and physical fitness while reducing psychological problems in children of multicultural families

PubMed Central

Park, Jae-Wan; Park, Seong-Hwan; Koo, Chang-Mo; Eun, Denny; Kim, Kang-Ho; Lee, Chan-Bok; Ham, Joung-Hyun; Jang, Jeong-Hoon; Jee, Yong-Seok

2017-01-01

This study investigated the influence of physical education class (PEC) as an intervention method for aggression, sociality, stress, and physical fitness levels in children from multicultural families. The hypothesis was that participating in PEC would result in reduced aggression and stress and improved sociality and physical fitness in multicultural children. A three-item questionnaire, a body composition test, and physical fitness tests were given three times. Eighty-four subjects were divided into four groups: multicultural children who participated in PEC (multi-PEG, n=12), multicultural children who did not participate in PEC (multi-NPEG, n=13), single-cultural children who participated in PEC (sing-PEG, n=11), and single-cultural children who did not participate in PEC (sing-NPEG, n=12), respectively. Parametric and nonparametric statistical methods were conducted on the collected data with a significance level set a priori at P<0.05. After 8 weeks of PEC, fat mass (F=2.966, P=0.045) and body mass index (F=3.654, P=0.021) had significantly different interaction effects. In the aspect of interaction effects from physical fitness variables, cardiopulmonary endurance (F=21.961, P=0.001), flexibility (F=8.892, P=0.001), muscular endurance (F=31.996, P=0.001), muscular strength (F=4.570, P=0.008), and power (F=24.479, P=0.001) were significantly improved in the multi-PEG compared to those of the other three groups. Moreover, sociality (F=22.144, P=0.001) in the multi-PEG was enhanced, whereas aggression (F=6.745, P=0.001) and stress (F=3.242, P=0.033) levels were reduced. As conclusion, the PEC reduced aggression and stress levels, and improved sociality and physical fitness levels after 8 weeks. This study confirmed that PEC for children from multicultural families can improve psychosocial factors and physical health. PMID:28503529

Inhibitory effects of rosmarinic acid on pterygium epithelial cells through redox imbalance and induction of extrinsic and intrinsic apoptosis.

PubMed

Chen, Ya-Yu; Tsai, Chia-Fang; Tsai, Ming-Chu; Hsu, Yu-Wen; Lu, Fung-Jou

2017-07-01

Pterygium is a common tumor-like ocular disease, which may be related to exposure to chronic ultraviolet (UV) radiation. Although the standard treatment for pterygium is surgical intervention, the recurrence rate of pterygium is high when no effective inhibitory drug is used after surgery. Rosmarinic acid (RA) is a polyphenol antioxidant with many biological activities, including anti-UV and anti-tumor properties. This study aimed to examine the inhibitory effects of RA on pterygium epithelial cells (PECs). Methylthiazolyldiphenyl-tetrazolium bromide (MTT) assay was used to examine the cell cytotoxicity of PECs after RA treatment. A fluorescent probe, DCFH-DA (2',7'-dichlorofluorescin diacetate), was stained with PECs to measure intracellular reactive oxygen species (ROS) levels. Antioxidant activity assays were used to measure the levels of superoxide dismutase (SOD) and catalase (CAT) in PECs. Western blot analysis was used to determine the protein expression of nuclear factor E2-related factor 2 (Nrf2), heme oxygenase 1 (HO-1), quinone acceptor oxidoreductase 1 (NQO1), and apoptosis-associated proteins. RA significantly reduced the cell viability of the PECs. Treatment with RA remarkably increased the Nrf2 protein expression levels in the nucleus, HO-1 and NQO1 protein expression levels, and the activities of SOD and CAT. As a result, intracellular ROS levels in PECs were decreased. Additionally, the induction of extrinsic apoptosis on PECs by RA was associated with increasing expressions levels of Fas, Fas-associated protein with death domain (FADD), tumor necrosis factor-alpha (TNF-α), and caspase 8 protein. Moreover, the induction of intrinsic apoptotic cell death in PECs was confirmed through upregulation of cytochrome c, Bax, caspase 9, and caspase 3 and downregulation of Bcl-2 and pro-caspase 3. Our study demonstrated that RA could inhibit the viability of PECs through regulation of extrinsic and intrinsic apoptosis pathways. Therefore, RA may have potential as a therapeutic medication for pterygium. Copyright © 2017 Elsevier Ltd. All rights reserved.

Regular physical education class enhances sociality and physical fitness while reducing psychological problems in children of multicultural families.

PubMed

Park, Jae-Wan; Park, Seong-Hwan; Koo, Chang-Mo; Eun, Denny; Kim, Kang-Ho; Lee, Chan-Bok; Ham, Joung-Hyun; Jang, Jeong-Hoon; Jee, Yong-Seok

2017-04-01

This study investigated the influence of physical education class (PEC) as an intervention method for aggression, sociality, stress, and physical fitness levels in children from multicultural families. The hypothesis was that participating in PEC would result in reduced aggression and stress and improved sociality and physical fitness in multicultural children. A three-item questionnaire, a body composition test, and physical fitness tests were given three times. Eighty-four subjects were divided into four groups: multicultural children who participated in PEC (multi-PEG, n=12), multicultural children who did not participate in PEC (multi-NPEG, n=13), single-cultural children who participated in PEC (sing-PEG, n=11), and single-cultural children who did not participate in PEC (sing-NPEG, n=12), respectively. Parametric and nonparametric statistical methods were conducted on the collected data with a significance level set a priori at P <0.05. After 8 weeks of PEC, fat mass ( F =2.966, P =0.045) and body mass index ( F =3.654, P =0.021) had significantly different interaction effects. In the aspect of interaction effects from physical fitness variables, cardiopulmonary endurance ( F =21.961, P =0.001), flexibility ( F =8.892, P =0.001), muscular endurance ( F =31.996, P =0.001), muscular strength ( F =4.570, P =0.008), and power ( F =24.479, P =0.001) were significantly improved in the multi-PEG compared to those of the other three groups. Moreover, sociality ( F =22.144, P =0.001) in the multi-PEG was enhanced, whereas aggression ( F =6.745, P =0.001) and stress ( F =3.242, P =0.033) levels were reduced. As conclusion, the PEC reduced aggression and stress levels, and improved sociality and physical fitness levels after 8 weeks. This study confirmed that PEC for children from multicultural families can improve psychosocial factors and physical health.

The Picture Exchange Communication System.

PubMed

Bondy, A; Frost, L

2001-10-01

The Picture Exchange Communication System (PECS) is an alternative/augmentative communication system that was developed to teach functional communication to children with limited speech. The approach is unique in that it teaches children to initiate communicative interactions within a social framework. This article describes the advantages to implementing PECS over traditional approaches. The PECS training protocol is described wherein children are taught to exchange a single picture for a desired item and eventually to construct picture-based sentences and use a variety of attributes in their requests. The relationship of PECS's implementation to the development of speech in previously nonvocal students is reviewed.

Ultrasound description of Pecs II (modified Pecs I): a novel approach to breast surgery.

PubMed

Blanco, R; Fajardo, M; Parras Maldonado, T

2012-11-01

The Pecs block (pectoral nerves block) is an easy and reliable superficial block inspired by the infraclavicular block approach and the transversus abdominis plane blocks. Once the pectoralis muscles are located under the clavicle the space between the two muscles is dissected to reach the lateral pectoral and the medial pectoral nerves. The main indications are breast expanders and subpectoral prosthesis where the distension of these muscles is extremely painful. A second version of the Pecs block is described, called "modified Pecs block" or Pecs block type II. This novel approach aims to block at least the pectoral nerves, the intercostobrachial, intercostals III-IV-V-VI and the long thoracic nerve. These nerves need to be blocked to provide complete analgesia during breast surgery, and it is an alternative or a rescue block if paravertebral blocks and thoracic epidurals failed. This block has been used in our unit in the past year for the Pecs I indications described, and in addition for, tumorectomies, wide excisions, and axillary clearances. The ultrasound sequence to perform this block is shown, together with simple X-ray dye images and gadolinium MRI images to understand the spread and pathways that can explain the benefit of this novel approach. Copyright © 2012 Sociedad Española de Anestesiología, Reanimación y Terapéutica del Dolor. Published by Elsevier España. All rights reserved.

Molecular interactions in self-assembled nano-structures of chitosan-sodium alginate based polyelectrolyte complexes.

PubMed

Wasupalli, Geeta Kumari; Verma, Devendra

2018-03-16

We report here the self-assembled structures of polyelectrolyte complexes (PECs) of polyanionic sodium alginate with the polycationic chitosan at room temperature. The PECs prepared at different pH values exhibited two distinct morphologies. The chitosan-alginate PECs self-assembled into the fibrous structure in a low pH range of pH3 to 7. The PECs obtained at high pH series around pH8 and above resulted in the formation of colloidal nanoparticles in the range of 120±9.48nm to 46.02±16.66nm. The zeta potential measurement showed that PECs prepared at lower pH (pH<6) exhibited nearly neutral surface charge, whereas PECs prepared at higher pH than 6 exhibited highly negative surface charge. The molecular interactions in nano-colloids and fibers were evaluated using FTIR analysis. The results attest that the ionic state of the chitosan and alginate plays an important role controlling the morphologies of the PECS. The present study has identified the enormous potential of the polyelectrolytes complexes to exploit shape by the alteration of ionic strength. These findings might be useful in the development of novel biomaterial. The produced fibers and nanocolloids could be applied as a biomaterial for tissue engineering and drug delivery. Copyright © 2017. Published by Elsevier B.V.

Human Primary Intestinal Epithelial Cells as an Improved In Vitro Model for Cryptosporidium parvum Infection

PubMed Central

Cabada, Miguel M.; Nichols, Joan; Gomez, Guillermo; White, A. Clinton

2013-01-01

The study of human intestinal pathogens has been limited by the lack of methods for the long-term culture of primary human intestinal epithelial cells (PECs). The development of infection models with PECs would allow a better understanding of host-parasite interactions. The objective of this study was to develop a novel method for prolonged in vitro cultivation of PECs that can be used to study Cryptosporidium infection. We isolated intact crypts from human intestines removed during weight loss surgery. The fragments of intestinal layers were cultivated with culture medium supplemented with growth factors and antiapoptotic molecules. After 7 days, the PECs formed self-regenerating cell clusters, forming villi that resemble intestinal epithelium. The PECs proliferated and remained viable for at least 60 days. The cells expressed markers for intestinal stem cells, epithelial cells, and mature enterocytes. The PECs were infected with Cryptosporidium. In contrast to older models in which parasite numbers decay, the burden of parasites increased for >120 h. In summary, we describe here a novel method for the cultivation of self-regenerating human epithelial cells from small intestinal crypts, which contain both intestinal stem cells and mature villus cells. We present data that suggest these cells support Cryptosporidium better than existing cell lines. PECs should provide an improved tool for studying host-parasite interactions involving Cryptosporidium and other intestinal pathogens. PMID:23509153

The PEC Network 1993. Directory of the Peace Education Commission. Peace Education Miniprints, No. 47.

ERIC Educational Resources Information Center

Bjerstedt, Ake, Ed.

This extensive list of the council members of the Peace Education Commission (PEC) from 1992-1994 gives mailing addresses and some telephone and fax numbers to enable direct contact with network members. The Peace Education Commission (PEC) facilitates international cooperation among individuals interested in peace education and research related…

Introducing the PEC Network: Mailing Addresses of the Peace Education Commission. Peace Education Miniprints No. 1.

ERIC Educational Resources Information Center

Bjerstedt, Ake, Ed.

The Peace Education Commission (PEC) was established to facilitate international cooperation among individuals interested in peace education and research related to the field. The major ambition of PEC is to serve as a useful network for transnational information and support in the peace education area. This document gives current mailing…

Meta-Analysis of PECS with Individuals with ASD: Investigation of Targeted versus Non-Targeted Outcomes, Participant Characteristics, and Implementation Phase

ERIC Educational Resources Information Center

Ganz, Jennifer B.; Davis, John L.; Lund, Emily M.; Goodwyn, Fara D.; Simpson, Richard L.

2012-01-01

The Picture Exchange Communication System (PECS) is a widely used picture/icon aided augmentative communication system designed for learners with autism and other developmental disorders. This meta-analysis analyzes the extant empirical literature for PECS relative to targeted (functional communication) and non-targeted concomitant outcomes…

Picture Exchange Communication System with Individuals with Developmental Disabilities: A Meta-Analysis of Single Subject Studies

ERIC Educational Resources Information Center

Hart, Stephanie L.; Banda, Devender R.

2010-01-01

Picture Exchange Communication System (PECS) is a picture-based communication strategy used to teach communication skills to persons with developmental disabilities including autism. This article systematically reviews 13 published single-subject studies to examine the effectiveness of PECS, the effects of PECS on speech and problem behaviors,…

Hydraulic properties of 3D rough-walled fractures during shearing: An experimental study

NASA Astrophysics Data System (ADS)

Yin, Qian; Ma, Guowei; Jing, Hongwen; Wang, Huidong; Su, Haijian; Wang, Yingchao; Liu, Richeng

2017-12-01

This study experimentally analyzed the influence of shear processes on nonlinear flow behavior through 3D rough-walled rock fractures. A high-precision apparatus was developed to perform stress-dependent fluid flow tests of fractured rocks. Then, water flow tests on rough-walled fractures with different mechanical displacements were conducted. At each shear level, the hydraulic pressure ranged from 0 to 0.6 MPa, and the normal load varied from 7 to 35 kN. The results show that (i) the relationship between the volumetric flow rate and hydraulic gradient of rough-walled fractures can be well fit using Forchheimer's law. Notably, both the linear and nonlinear coefficients in Forchheimer's law decrease during shearing; (ii) a sixth-order polynomial function is used to evaluate the transmissivity based on the Reynolds number of fractures during shearing. The transmissivity exhibits a decreasing trend as the Reynolds number increases and an increasing trend as the shear displacement increases; (iii) the critical hydraulic gradient, critical Reynolds number and equivalent hydraulic aperture of the rock fractures all increase as the shear displacement increases. When the shear displacement varies from 0 to 15 mm, the critical hydraulic gradient ranges from 0.3 to 2.2 for a normal load of 7 kN and increases to 1.8-8.6 for a normal load of 35 kN; and (iv) the Forchheimer law results are evaluated by plotting the normalized transmissivity of the fractures during shearing against the Reynolds number. An increase in the normal load shifts the fitted curves downward. Additionally, the Forchheimer coefficient β decreases with the shear displacement but increases with the applied normal load.

Synthesis and in vitro characterization of entirely S-protected thiolated pectin for drug delivery.

PubMed

Hintzen, Fabian; Hauptstein, Sabine; Perera, Glen; Bernkop-Schnürch, Andreas

2013-11-01

The study was aimed to synthesize a thiolated polymer (thiomer) that is resistant to oxidation in solutions above pH 5. In order to protect a pectin-cysteine conjugate against premature oxidation, the thiomer was S-protected by a disulfide connected leaving group. Therefore, 2-mercaptonicotinic acid was first coupled to L-cysteine by a disulfide exchange reaction and the purified product was subsequently attached to pectin by a carbodiimide mediated amid bond formation. The obtained fully S-protected thiolated pectin was in vitro characterized with respect to co- and mucoadhesive properties and stability toward oxidation. The results indicated a 1.8-fold and 2.3-fold enhanced disintegration time at pH 6.8 of the S-protected thiolated pectin (Pec-Cys-MNA) compared to thiolated pectin (Pec-Cys) and unmodified pectin (Pec). Moreover, rheological measurements of polymer/mucus mixtures showed a 1.6-fold (compared to Pec-Cys) and 6.7-fold (compared to Pec) increased dynamic viscosity of Pec-Cys-MNA. On the other hand, in the presence of a strong oxidizing agent such as H2O2 (0.3% v/v), no increase in viscosity of Pec-Cys-MNA could be observed. A 6-month experiment also demonstrated the long-term stability of a liquid formulation based on Pec-Cys-MNA. Further investigations proved that the first time all thiol groups on a thiolated polymer could be protected owing to the novel synthesis. Accordingly, these features may help to develop thiomer based liquid or gel formulations targeting mucosal surfaces such as nasal, ocular or vaginal drug delivery systems. Copyright © 2013 Elsevier B.V. All rights reserved.

Long-term effects of PECS on social-communicative skills of children with autism spectrum disorders: a follow-up study.

PubMed

Lerna, Anna; Esposito, Dalila; Conson, Massimiliano; Massagli, Angelo

2014-01-01

The Picture Exchange Communication System (PECS) is a popular augmentative communication system frequently used with 'nonverbal' children with autism. Several studies suggested that PECS could represent an effective tool for promoting improvement of several social-communicative skills. Only sparse evidence is instead available on the long-term effectiveness of this treatment system. To test the long-term effects of PECS, for which a follow-up study was conducted by assessing social-communicative skills in nonverbal preschool children with autism after 12 months from treatment completion. Two groups of children (N = 14) were assessed; one group had completed the PECS training and the other conventional language therapy (CLT). At follow-up all children received the same pre- and post-treatment assessment. Outcome measures were the following: Communication and Social domains of Autism Diagnostic Observation Schedule (ADOS); Language and Personal-Social subscales of the Griffiths' Mental Developmental Scales (GMDS); Communication and Social Abilities domains of the Vineland Adaptive Behavior Scales (VABS); and several social-communicative variables coded in an unstructured setting. The PECS group showed significant improvements compared with the CLT group on ADOS severity scores (Communication, Social and Total), on GMDS Social domain and on VABS Communication and Social domains. PECS-related gains on the VABS Social domain and on specific social-communicative measures coded during free-play, i.e. frequency of joint attention and initiation, and duration of cooperative play, were stable after 1-year follow-up. Cooperative play continued to improve on follow-up with respect to both post- and pre-treatment assessment. These findings demonstrated that PECS training can promote long-term enhancement of specific socio-communicative skills in children with autism. © 2014 Royal College of Speech and Language Therapists.

Social-communicative effects of the Picture Exchange Communication System (PECS) in autism spectrum disorders.

PubMed

Lerna, Anna; Esposito, Dalila; Conson, Massimiliano; Russo, Luigi; Massagli, Angelo

2012-01-01

The Picture Exchange Communication System (PECS) is a common treatment choice for non-verbal children with autism. However, little empirical evidence is available on the usefulness of PECS in treating social-communication impairments in autism. To test the effects of PECS on social-communicative skills in children with autism, concurrently taking into account standardized psychometric data, standardized functional assessment of adaptive behaviour, and information on social-communicative variables coded in an unstructured setting. Eighteen preschool children (mean age = 38.78 months) were assigned to two intervention approaches, i.e. PECS and Conventional Language Therapy (CLT). Both PECS (Phases I-IV) and CLT were delivered three times per week, in 30-min sessions, for 6 months. Outcome measures were the following: Autism Diagnostic Observation Schedule (ADOS) domain scores for Communication and Reciprocal Social Interaction; Language and Personal-Social subscales of the Griffiths' Mental Developmental Scales (GMDS); Communication and Social Abilities domains of the Vineland Adaptive Behavior Scales (VABS); and several social-communicative variables coded in an unstructured setting. Results demonstrated that the two groups did not differ at Time 1 (pre-treatment assessment), whereas at Time 2 (post-test) the PECS group showed a significant improvement with respect to the CLT group on the VABS social domain score and on almost all the social-communicative abilities coded in the unstructured setting (i.e. joint attention, request, initiation, cooperative play, but not eye contact). These findings showed that PECS intervention (Phases I-IV) can improve social-communicative skills in children with autism. This improvement is especially evident in standardized measures of adaptive behaviour and measures derived from the observation of children in an unstructured setting. © 2012 Royal College of Speech and Language Therapists.

Human and Avian Extraintestinal Pathogenic Escherichia coli: Infections, Zoonotic Risks, and Antibiotic Resistance Trends

PubMed Central

2013-01-01

Abstract Extraintestinal pathogenic Escherichia coli (ExPEC) constitutes ongoing health concerns for women, newborns, elderly, and immunocompromised individuals due to increased numbers of urinary tract infections (UTIs), newborn meningitis, abdominal sepsis, and septicemia. E. coli remains the leading cause of UTIs, with recent investigations reporting the emergence of E. coli as the predominant cause of nosocomial and neonatal sepsis infections. This shift from the traditional Gram-positive bacterial causes of nosocomial and neonatal sepsis infections could be attributed to the use of intrapartum chemoprophylaxis against Gram-positive bacteria and the appearance of antibiotic (ATB) resistance in E. coli. While ExPEC strains cause significant healthcare concerns, these bacteria also infect chickens and cause the poultry industry economic losses due to costs of containment, mortality, and disposal of carcasses. To circumvent ExPEC-related costs, ATBs are commonly used in the poultry industry to prevent/treat microbial infections and promote growth and performance. In an unfortunate linkage, chicken products are suspected to be a source of foodborne ExPEC infections and ATB resistance in humans. Therefore, the emergence of multidrug resistance (MDR) (resistance to three or more classes of antimicrobial agents) among avian E. coli has created major economic and health concerns, affecting both human healthcare and poultry industries. Increased numbers of immunocompromised individuals, including the elderly, coupled with MDR among ExPEC strains, will continue to challenge the treatment of ExPEC infections and likely lead to increased treatment costs. With ongoing complications due to emerging ATB resistance, novel treatment strategies are necessary to control ExPEC infections. Recognizing and treating the zoonotic risk posed by ExPEC would greatly enhance food safety and positively impact human health. PMID:23962019

Boundary layer simulator improvement

NASA Technical Reports Server (NTRS)

Praharaj, S. C.; Schmitz, C.; Frost, C.; Engel, C. D.; Fuller, C. E.; Bender, R. L.; Pond, J.

1984-01-01

High chamber pressure expander cycles proposed for orbit transfer vehicles depend primarily on the heat energy transmitted from the combustion products through the thrust wall chamber wall. The heat transfer to the nozzle wall is affected by such variables as wall roughness, relamarization, and the presence of particles in the flow. Motor performance loss for these nozzles with thick boundary layers is inaccurate using the existing procedure coded BLIMPJ. Modifications and innovations to the code are examined. Updated routines are listed.

Parietal Epithelial Cells Participate in the Formation of Sclerotic Lesions in Focal Segmental Glomerulosclerosis

PubMed Central

Smeets, Bart; Kuppe, Christoph; Sicking, Eva-Maria; Fuss, Astrid; Jirak, Peggy; van Kuppevelt, Toin H.; Endlich, Karlhans; Wetzels, Jack F.M.; Gröne, Hermann-Josef; Floege, Jürgen

2011-01-01

The pathogenesis of the development of sclerotic lesions in focal segmental glomerulosclerosis (FSGS) remains unknown. Here, we selectively tagged podocytes or parietal epithelial cells (PECs) to determine whether PECs contribute to sclerosis. In three distinct models of FSGS (5/6-nephrectomy + DOCA-salt; the murine transgenic chronic Thy1.1 model; or the MWF rat) and in human biopsies, the primary injury to induce FSGS associated with focal activation of PECs and the formation of cellular adhesions to the capillary tuft. From this entry site, activated PECs invaded the affected segment of the glomerular tuft and deposited extracellular matrix. Within the affected segment, podocytes were lost and mesangial sclerosis developed within the endocapillary compartment. In conclusion, these results demonstrate that PECs contribute to the development and progression of the sclerotic lesions that define FSGS, but this pathogenesis may be relevant to all etiologies of glomerulosclerosis. PMID:21719782

Hierarchical Cu2O foam/g-C3N4 photocathode for photoelectrochemical hydrogen production

NASA Astrophysics Data System (ADS)

Ma, Xinzhou; Zhang, Jingtao; Wang, Biao; Li, Qiuguo; Chu, Sheng

2018-01-01

Solar photoelectrochemical (PEC) hydrogen production is a promising way for solving energy and environment problems. Earth-abundant Cu2O is a potential light absorber for PEC hydrogen production. In this article, hierarchical porous Cu2O foams are prepared by thermal oxidation of the electrochemically deposited Cu foams. PEC performances of the Cu2O foams are systematically studied and discussed. Benefiting from their higher light harvesting and more efficient charge separation, the Cu2O foams demonstrate significantly enhanced photocurrents and photostability compared to their film counterparts. Moreover, by integrating g-C3N4, hierarchical Cu2O foam/g-C3N4 composites are prepared with further improved photocurrent and photostability, appearing to be potential photocathodes for solar PEC hydrogen production. This study may provide a new and useful insight for the development of Cu2O-based photocathodes for PEC hydrogen production.

Parent-implemented picture exchange communication system (PECS) training: an analysis of YouTube videos.

PubMed

Jurgens, Anneke; Anderson, Angelika; Moore, Dennis W

2012-01-01

To investigate the integrity with which parents and carers implement PECS in naturalistic settings, utilizing a sample of videos obtained from YouTube. Twenty-one YouTube videos meeting selection criteria were identified. The videos were reviewed for instances of seven implementer errors and, where appropriate, presence of a physical prompter. Forty-three per cent of videos and 61% of PECS exchanges contained errors in parent implementation of specific teaching strategies of the PECS training protocol. Vocal prompts, incorrect error correction and the absence of timely reinforcement occurred most frequently, while gestural prompts, insistence on speech, incorrect use of the open hand prompt and not waiting for the learner to initiate occurred less frequently. Results suggest that parents engage in vocal prompting and incorrect use of the 4-step error correction strategy when using PECS with their children, errors likely to result in prompt dependence.

Modeling and Simulations in Photoelectrochemical Water Oxidation: From Single Level to Multiscale Modeling.

PubMed

Zhang, Xueqing; Bieberle-Hütter, Anja

2016-06-08

This review summarizes recent developments, challenges, and strategies in the field of modeling and simulations of photoelectrochemical (PEC) water oxidation. We focus on water splitting by metal-oxide semiconductors and discuss topics such as theoretical calculations of light absorption, band gap/band edge, charge transport, and electrochemical reactions at the electrode-electrolyte interface. In particular, we review the mechanisms of the oxygen evolution reaction, strategies to lower overpotential, and computational methods applied to PEC systems with particular focus on multiscale modeling. The current challenges in modeling PEC interfaces and their processes are summarized. At the end, we propose a new multiscale modeling approach to simulate the PEC interface under conditions most similar to those of experiments. This approach will contribute to identifying the limitations at PEC interfaces. Its generic nature allows its application to a number of electrochemical systems. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Surface roughness influences on the behaviour of flow inside microchannels

NASA Astrophysics Data System (ADS)

Farias, M. H.; Castro, C. S.; Garcia, D. A.; Henrique, J. S.

2018-03-01

This work discusses influence of the surface roughness on the behavior of liquids flowing inside microchannels. By measuring the flow profile using the micro-PIV technique, the flow of water inside two rectangular microchannels of different wall roughness and in a circular smooth microchannel was studied. Comparisons were made among the experimental results, showing that a metrological approach concerning surface characteristics of microdevices is required to ensure reliability of the measurements for flow analyses in microfluidic processes.

Surface Features Parameterization and Equivalent Roughness Height Estimation of a Real Subglacial Conduit in the Arctic

NASA Astrophysics Data System (ADS)

Chen, Y.; Liu, X.; Mankoff, K. D.; Gulley, J. D.

2016-12-01

The surfaces of subglacial conduits are very complex, coupling multi-scale roughness, large sinuosity, and cross-sectional variations together. Those features significantly affect the friction law and drainage efficiency inside the conduit by altering velocity and pressure distributions, thus posing considerable influences on the dynamic development of the conduit. Parameterizing the above surface features is a first step towards understanding their hydraulic influences. A Matlab package is developed to extract the roughness field, the conduit centerline, and associated area and curvature data from the conduit surface, acquired from 3D scanning. By using those data, the characteristic vertical and horizontal roughness scales are then estimated based on the structure functions. The centerline sinuosities, defined through three concepts, i.e., the traditional definition of a fluvial river, entropy-based sinuosity, and curvature-based sinuosity, are also calculated and compared. The cross-sectional area and equivalent circular diameter along the centerline are also calculated. Among those features, the roughness is especially important due to its pivotal role in determining the wall friction, and thus an estimation of the equivalent roughness height is of great importance. To achieve such a goal, the original conduit is firstly simplified into a straight smooth pipe with the same volume and centerline length, and the roughness field obtained above is then reconstructed into the simplified pipe. An OpenFOAM-based Large-eddy-simulation (LES) is then performed based on the reconstructed pipe. Considering that the Reynolds number is of the order 106, and the relative roughness is larger than 5% for 60% of the conduit, we test the validity of the resistance law for completely rough pipe. The friction factor is calculated based on the pressure drop and mean velocity in the simulation. Working together, the equivalent roughness height can be calculated. However, whether the assumption is applicable for the current case, i.e., high relative roughness, is a question. Two other roughness heights, i.e., the vertical roughness scale based on structure functions and viscous sublayer thickness determined from the wall boundary layer are also calculated and compared with the equivalent roughness height.

Recent Results of Turbulence Research

NASA Technical Reports Server (NTRS)

Prandtl, L

1933-01-01

The first sections of this report deal with two prominent questions, namely the origin of turbulence and the characteristics of turbulent currents. In the third section conclusions are drawn for the flow along a rough wall, whereby an important relation for the velocity distribution is revealed. The principles are also applied to straight rough and smooth tubes.

Membership Directory of the PEC Network: Mailing Addresses of the Peace Education Commission. Peace Education Miniprints No. 21.

ERIC Educational Resources Information Center

Bjerstedt, Ake, Ed.

The Peace Education Commission (PEC) was established to facilitate international cooperation among individuals interested in peace education and research related to peace education. The main ambition of PEC is to serve as a useful network for transnational information and support in the peace education area. This document provides current mailing…

Effectiveness of the Picture Exchange Communication System (PECS) on Communication and Speech for Children with Autism Spectrum Disorders: A Meta-Analysis

ERIC Educational Resources Information Center

Flippin, Michelle; Reszka, Stephanie; Watson, Linda R.

2010-01-01

Purpose: The Picture Exchange Communication System (PECS) is a popular communication-training program for young children with autism spectrum disorders (ASD). This meta-analysis reviews the current empirical evidence for PECS in affecting communication and speech outcomes for children with ASD. Method: A systematic review of the literature on PECS…

Acquisition and Generalization of the Picture Exchange Communication System Behaviors across Settings, Persons, and Stimulus Classes with Three Students with Autism

ERIC Educational Resources Information Center

Dogoe, Maud S.; Banda, Devender R.; Lock, Robin H.

2010-01-01

This study examined the acquisition and generalization of requesting behaviors learned through PECS with three children with autism. A single-subject multiple baseline across participants design was used to determine the effects of PECS. Results indicated that all three participants acquired PECS skills for requesting and generalized the skills…

Pectoral nerve block (Pecs block) with sedation for breast conserving surgery without general anesthesia.

PubMed

Moon, Eun-Jin; Kim, Seung-Beom; Chung, Jun-Young; Song, Jeong-Yoon; Yi, Jae-Woo

2017-09-01

Most regional anesthesia in breast surgeries is performed as postoperative pain management under general anesthesia, and not as the primary anesthesia. Regional anesthesia has very few cardiovascular or pulmonary side-effects, as compared with general anesthesia. Pectoral nerve block is a relatively new technique, with fewer complications than other regional anesthesia. We performed Pecs I and Pec II block simultaneously as primary anesthesia under moderate sedation with dexmedetomidine for breast conserving surgery in a 49-year-old female patient with invasive ductal carcinoma. Block was uneventful and showed no complications. Thus, Pecs block with sedation could be an alternative to general anesthesia for breast surgeries.

Roughness of Ti Substrates for Control of the Preferred Orientation of TiO 2 Nanotube Arrays as a New Orientation Factor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seong, Won Mo; Kim, Dong Hoe; Park, Ik Jae

2015-06-11

We report the surface roughness of a Ti substrate as a critical factor for controlling the degree of the preferred orientation of anatase TiO2 nanotube arrays (NTAs) which are synthesized by anodization and a subsequent annealing process. The degree of the preferred orientation to the (004) plane of the anatase crystal structure has a strong dependency on the root-mean-square roughness (Sq) of the initial Ti substrate when the roughness-controlled substrates are anodized in an ethylene glycol-based electrolyte containing ~2 wt % of water. Highly preferred oriented NTAs were obtained from low-Sq (<10 nm) substrates, which were accompanied by uniform poremore » distribution and low concentration of hydroxyl ions in as-anodized amorphous NTAs. The mechanism of the preferred oriented crystallization of nanometer-scaled tube walls is explained considering the microscopic geometrical uniformity of the oxide barrier and nanopores at the early stage of anodization, which affected the local electric field and thus the insertion of the hydroxyl group into the amorphous TiO2 tube walls.« less

The expression of xenobiotic-metabolizing enzymes in human prostate and in prostate epithelial cells (PECs) derived from primary cultures.

PubMed

Al-Buheissi, S Z; Cole, K J; Hewer, A; Kumar, V; Bryan, R L; Hudson, D L; Patel, H R; Nathan, S; Miller, R A; Phillips, D H

2006-06-01

Dietary heterocyclic amines (HCAs) are carcinogenic in rodent prostate requiring activation by enzymes such as cytochrome P450 (CYP) and N-acetyltransferase (NAT). We investigated by Western blotting and immunohistochemistry the expression of CYP1A1, CYP1A2, and NAT1 in human prostate and in prostate epithelial cells (PECs) derived from primary cultures and tested their ability to activate the dietary carcinogen 2-amino-3-methylimidazo[4,5-f]quinoline (IQ) and its N-hydroxy metabolite (N-OH-IQ) to DNA-damaging moieties. Western blotting identified CYP1A1, CYP1A2, and NAT1. Immunohistochemistry localized NAT1 to the cytoplasm of PECs. Inter-individual variation was observed in the expression levels of CYP1A1, 1A2, and NAT1 (11, 75, and 35-fold, respectively). PECs expressed CYP1A1 and NAT1 but not CYP1A2. When incubated with IQ or N-OH-IQ, PECs formed DNA adducts indicating their ability to metabolically activate these compounds. Prostate cells possess the capacity to activate dietary carcinogens. PECs may provide a useful model system to study their role in prostate carcinogenesis.

High-aspect ratio micro- and nanostructures enabled by photo-electrochemical etching for sensing and energy harvesting applications

NASA Astrophysics Data System (ADS)

Alhalaili, Badriyah; Dryden, Daniel M.; Vidu, Ruxandra; Ghandiparsi, Soroush; Cansizoglu, Hilal; Gao, Yang; Saif Islam, M.

2018-03-01

Photo-electrochemical (PEC) etching can produce high-aspect ratio features, such as pillars and holes, with high anisotropy and selectivity, while avoiding the surface and sidewall damage caused by traditional deep reactive ion etching (DRIE) or inductively coupled plasma (ICP) RIE. Plasma-based techniques lead to the formation of dangling bonds, surface traps, carrier leakage paths, and recombination centers. In pursuit of effective PEC etching, we demonstrate an optical system using long wavelength (λ = 975 nm) infra-red (IR) illumination from a high-power laser (1-10 W) to control the PEC etching process in n-type silicon. The silicon wafer surface was patterned with notches through a lithography process and KOH etching. Then, PEC etching was introduced by illuminating the backside of the silicon wafer to enhance depth, resulting in high-aspect ratio structures. The effect of the PEC etching process was optimized by varying light intensities and electrolyte concentrations. This work was focused on determining and optimizing this PEC etching technique on silicon, with the goal of expanding the method to a variety of materials including GaN and SiC that are used in designing optoelectronic and electronic devices, sensors and energy harvesting devices.

Chasing the long tail of environmental data: PEcAn is nuts about Brown Dog

NASA Astrophysics Data System (ADS)

Dietze, M.; Cowdery, E.; Desai, A. R.; Gardella, A.; Kelly, R.; Kooper, R.; LeBauer, D.; Mantooth, J.; McHenry, K.; Serbin, S.; Shiklomanov, A. N.; Simkins, J.; Viskari, T.; Raiho, A.

2015-12-01

The Predictive Ecosystem Analyzer (PEcAn) is a ecological modeling informatics system that manages the flows of information in and out of terrestrial biosphere models, provenance tracking, visualization, analysis, and model-data fusion. We are in the process of scaling the PEcAn system from one that currently supports a handful of models and system nodes to one that aims to provide bottom-up connectivity across much of the model-data integration done by the terrestrial biogeochemistry community. This talk reports on the current state of PEcAn, it's data processing workflows, and the near- and long-term challenges faced. Particular emphasis will be given to the tools being developed by the Brown Dog project to make unstructured, un-curated data more accessible: the Data Access Proxy (DAP) and the Data Tilling Service (DTS). The use of the DAP to process meteorological data and the DTS to read vegetation data will be demonstrated and other Brown Dog environmental case studies will be briefly touched on. Beyond data processing, facilitating data discovery and import into PEcAn and distributing analyses across the PEcAn network (i.e. bringing models to data) are key challenges moving forward.

Boundary layer simulator improvement

NASA Technical Reports Server (NTRS)

Praharaj, Sarat C.; Schmitz, Craig P.; Nouri, Joseph A.

1989-01-01

Boundary Layer Integral Matrix Procedure (BLIMPJ) has been identified by the propulsion community as the rigorous boundary layer program in connection with the existing JANNAF reference programs. The improvements made to BLIMPJ and described herein have potential applications in the design of the future Orbit Transfer Vehicle engines. The turbulence model is validated to include the effects of wall roughness and a way is devised to treat multiple smooth-rough surfaces. A prediction of relaminarization regions is examined as is the combined effects of wall cooling and surface roughness on relaminarization. A turbulence model to represent the effects of constant condensed phase loading is given. A procedure is described for thrust decrement calculation in thick boundary layers by coupling the T-D Kinetics Program and BLIMPJ and a way is provided for thrust loss optimization. Potential experimental studies in rocket nozzles are identified along with the required instrumentation to provide accurate measurements in support of the presented new analytical models.

Computing nonhydrostatic shallow-water flow over steep terrain

USGS Publications Warehouse

Denlinger, R.P.; O'Connell, D. R. H.

2008-01-01

Flood and dambreak hazards are not limited to moderate terrain, yet most shallow-water models assume that flow occurs over gentle slopes. Shallow-water flow over rugged or steep terrain often generates significant nonhydrostatic pressures, violating the assumption of hydrostatic pressure made in most shallow-water codes. In this paper, we adapt a previously published nonhydrostatic granular flow model to simulate shallow-water flow, and we solve conservation equations using a finite volume approach and an Harten, Lax, Van Leer, and Einfeldt approximate Riemann solver that is modified for a sloping bed and transient wetting and drying conditions. To simulate bed friction, we use the law of the wall. We test the model by comparison with an analytical solution and with results of experiments in flumes that have steep (31??) or shallow (0.3??) slopes. The law of the wall provides an accurate prediction of the effect of bed roughness on mean flow velocity over two orders of magnitude of bed roughness. Our nonhydrostatic, law-of-the-wall flow simulation accurately reproduces flume measurements of front propagation speed, flow depth, and bed-shear stress for conditions of large bed roughness. ?? 2008 ASCE.

Effect of nano-scale morphology on micro-channel wall surface and electrical characterization in lead silicate glass micro-channel plate

NASA Astrophysics Data System (ADS)

Cai, Hua; Li, Fangjun; Xu, Yanglei; Bo, Tiezhu; Zhou, Dongzhan; Lian, Jiao; Li, Qing; Cao, Zhenbo; Xu, Tao; Wang, Caili; Liu, Hui; Li, Guoen; Jia, Jinsheng

2017-10-01

Micro-channel plate (MCP) is a two dimensional arrays of microscopic channel charge particle multiplier. Silicate composition and hydrogen reduction are keys to determine surface morphology of micro-channel wall in MCP. In this paper, lead silicate glass micro-channel plates in two different cesium contents (0at%, 0.5at%) and two different hydrogen reduction temperatures (400°C,450°C) were present. The nano-scale morphology, elements content and chemical states of microporous wall surface treated under different alkaline compositions and reduction conditions was investigated by Atomic Force Microscopy (AFM) and X-ray Photoelectron Spectroscopy (XPS), respectively. Meanwhile, the electrical characterizations of MCP, including the bulk resistance, electron gain and the density of dark current, were measured in a Vacuum Photoelectron Imaging Test Facility (VPIT).The results indicated that the granular phase occurred on the surface of microporous wall and diffuses in bulk glass is an aggregate of Pb atom derived from the reduction of Pb2+. In micro-channel plate, the electron gain and bulk resistance were mainly correlated to particle size and distribution, the density of dark current (DDC) went up with the increasing root-mean-square roughness (RMS) on the microporous wall surface. Adding cesiums improved the size of Pb atomic aggregation, lowered the relative concentration of [Pb] reduced from Pb2+ and decreased the total roughness of micro-channel wall surface, leading a higher bulk resistance, a lower electron gain and a less dark current. Increasing hydrogen reduction temperature also improved the size of Pb atomic aggregation, but enhanced the relative concentration of [Pb] and enlarged the total roughness of micro-channel wall surface, leading a higher bulk resistance, a lower electron gain and a larger dark current. The reasons for the difference of electrical characteristics were discussed.

Roughness Induced Transition in a Supersonic Boundary Layer

NASA Technical Reports Server (NTRS)

Balakumar, Ponnampalam; Kergerise, Michael A.

2013-01-01

Direct numerical simulation is used to investigate the transition induced by threedimensional isolated roughness elements in a supersonic boundary layer at a free stream Mach number of 3.5. Simulations are performed for two different configurations: one is a square planform roughness and the other is a diamond planform roughness. The mean-flow calculations show that the roughness induces counter rotating streamwise vortices downstream of the roughness. These vortices persist for a long distance downstream and lift the low momentum fluid from the near wall region and place it near the outer part of the boundary layer. This forms highly inflectional boundary layer profiles. These observations agree with recent experimental observations. The receptivity calculations showed that the amplitudes of the mass-flux fluctuations near the neutral point for the diamond shape roughness are the same as the amplitude of the acoustic disturbances. They are three times smaller for the square shape roughness.

Turbulent Flow Over Large Roughness Elements: Effect of Frontal and Plan Solidity on Turbulence Statistics and Structure

NASA Astrophysics Data System (ADS)

Placidi, M.; Ganapathisubramani, B.

2018-04-01

Wind-tunnel experiments were carried out on fully-rough boundary layers with large roughness (δ /h ≈ 10, where h is the height of the roughness elements and δ is the boundary-layer thickness). Twelve different surface conditions were created by using LEGO™ bricks of uniform height. Six cases are tested for a fixed plan solidity (λ _P) with variations in frontal density (λ _F), while the other six cases have varying λ _P for fixed λ _F. Particle image velocimetry and floating-element drag-balance measurements were performed. The current results complement those contained in Placidi and Ganapathisubramani (J Fluid Mech 782:541-566, 2015), extending the previous analysis to the turbulence statistics and spatial structure. Results indicate that mean velocity profiles in defect form agree with Townsend's similarity hypothesis with varying λ _F, however, the agreement is worse for cases with varying λ _P. The streamwise and wall-normal turbulent stresses, as well as the Reynolds shear stresses, show a lack of similarity across most examined cases. This suggests that the critical height of the roughness for which outer-layer similarity holds depends not only on the height of the roughness, but also on the local wall morphology. A new criterion based on shelter solidity, defined as the sheltered plan area per unit wall-parallel area, which is similar to the `effective shelter area' in Raupach and Shaw (Boundary-Layer Meteorol 22:79-90, 1982), is found to capture the departure of the turbulence statistics from outer-layer similarity. Despite this lack of similarity reported in the turbulence statistics, proper orthogonal decomposition analysis, as well as two-point spatial correlations, show that some form of universal flow structure is present, as all cases exhibit virtually identical proper orthogonal decomposition mode shapes and correlation fields. Finally, reduced models based on proper orthogonal decomposition reveal that the small scales of the turbulence play a significant role in assessing outer-layer similarity.

Smooth and selective photo-electrochemical etching of heavily doped GaN:Si using a mode-locked 355 nm microchip laser

NASA Astrophysics Data System (ADS)

Lee, SeungGeun; Mishkat-Ul-Masabih, Saadat; Leonard, John T.; Feezell, Daniel F.; Cohen, Daniel A.; Speck, James S.; Nakamura, Shuji; DenBaars, Steven P.

2017-01-01

We investigate the photo-electrochemical (PEC) etching of Si-doped GaN samples grown on nonpolar GaN substrates, using a KOH/K2S2O8 solution and illuminated by a Xe arc lamp or a Q-switched 355 nm laser. The etch rate with the arc lamp decreased as the doping concentration increased, and the etching stopped for concentrations above 7.7 × 1018 cm-3. The high peak intensity of the Q-switched laser extended the etchable concentration to 2.4 × 1019 cm-3, with an etch rate of 14 nm/min. Compositionally selective etching was demonstrated, with an RMS surface roughness of 1.6 nm after etching down to an n-Al0.20Ga0.80N etch stop layer.

Reduced-Volume Fracture Toughness Characterization for Transparent Polymers

DTIC Science & Technology

2015-03-21

Caruthers et al. (2004) developed a thermodynamically consistent, nonlinear viscoelastic bulk constitutive model based on a potential energy clock ( PEC ...except that relaxation times change. Because of its formulation, the PEC model predicts mechanical yield as a natural consequence of relaxation...softening type of behavior, but hysteresis effects are not naturally accounted for. Adolf et al. (2009) developed a method of simplifying the PEC model

Effects of Mother-Implemented Picture Exchange Communication System (PECS) Training on Independent Communicative Behaviors of Young Children with Autism Spectrum Disorders

ERIC Educational Resources Information Center

Park, Ju Hee; Alber-Morgan, Sheila R.; Cannella-Malone, Helen

2011-01-01

This study examined the effects of mother-implemented Picture Exchange Communication System (PECS) training on the independent communication of three young children with autism spectrum disorders. Three mothers were trained to teach their child PECS Phases 1 through 3B, which they did with high integrity. Moreover, all three children successfully…

T cell phenotype and intracellular IFN-γ production in peritoneal exudate cells and gut intraepithelial lymphocytes during acute Toxoplasma gondii infection in mice

PubMed Central

Shin, Dae-Whan

2002-01-01

Although there are many reports on the splenic (systemic) T cell response after Toxoplasma gondii infection, little information is available regarding the local T cell responses of peritoneal exudate cells (PEC) and gut intraepithelial lymphocytes (IEL) following peroral infection with bradyzoites. Mice were infected with 40 cysts of the 76K strain of T. gondii, and then sacrificed at days 0, 1, 4, 7 and 10 postinfection (PI). The cellular composition and T cell responses of PEC and IEL were analyzed. The total number of PEC and IEL per mouse increased after infection, but the ratio of increase was higher in IEL. Lymphocytes were the major component of both PEC and IEL. The relative percentages of PEC macrophages and neutrophils/eosinophils increased significantly at day 1 and 4 PI, whereas those of IEL did not change significantly. The percentage of PEC NK1.1 and γδ T cells peaked at day 4 PI (p < 0.0001), and CD4 and CD8α T cells increased continuously after infection. The percentages of IEL CD8α and γδ T cells decreased slightly at first, and then increased. CD4 and NK1.1 T cells of IEL did not change significantly after infection. IFN-γ-producing PEC NK1.1 T cells increased significantly from day 1 PI, but the other T cell subsets produced IFN-γ abundantly thereafter. The proportion of IEL IFN-γ-producing CD8α and γδ T cells increased significantly after infection, while IEL NK1.1 T cells had similar IFN-γ production patterns. Taken together, CD4 T cells were the major phenotype and the important IFN-γ-producing T cell subsets in PEC after oral infection with T. gondii, whereas CD8α T cells had these roles in IEL. These results suggest that PEC and IEL comprise different cell differentials and T cell responses, and according to infection route these factors may contribute to the different cellular immune responses. PMID:12325441

Genomic characterisation of an endometrial pathogenic Escherichia coli strain reveals the acquisition of genetic elements associated with extra-intestinal pathogenicity.

PubMed

Goldstone, Robert J; Popat, Roman; Schuberth, Hans-Joachim; Sandra, Olivier; Sheldon, I Martin; Smith, David G E

2014-12-06

Strains of Escherichia coli cause a wide variety of intestinal and extra-intestinal diseases in both humans and animals, and are also often found in healthy individuals or the environment. Broadly, a strong phylogenetic relationship exists that distinguishes most E. coli causing intestinal disease from those that cause extra-intestinal disease, however, isolates within a recently described subclass of Extra-Intestinal Pathogenic E. coli (ExPEC), termed endometrial pathogenic E. coli, tend to be phylogenetically distant from the vast majority of characterised ExPECs, and more closely related to human intestinal pathogens. In this work, we investigate the genetic basis for ExPEC infection in the prototypic endometrial pathogenic E. coli strain MS499. By investigating the genome of MS499 in comparison with a range of other E. coli sequences, we have discovered that this bacterium has acquired substantial lengths of DNA which encode factors more usually associated with ExPECs and less frequently found in the phylogroup relatives of MS499. Many of these acquired factors, including several iron acquisition systems and a virulence plasmid similar to that found in several ExPECs such as APEC O1 and the neonatal meningitis E. coli S88, play characterised roles in a variety of typical ExPEC infections and appear to have been acquired recently by the evolutionary lineage leading to MS499. Taking advantage of the phylogenetic relationship we describe between MS499 and several other closely related E. coli isolates from across the globe, we propose a step-wise evolution of a novel clade of sequence type 453 ExPECs within phylogroup B1, involving the recruitment of ExPEC virulence factors into the genome of an ancestrally non-extraintestinal E. coli, which has repurposed this lineage with the capacity to cause extraintestinal disease. These data reveal the genetic components which may be involved in this phenotype switching, and argue that horizontal gene exchange may be a key factor in the emergence of novel lineages of ExPECs.

Influence of Surface Roughness on the Second Order Transport of Turbulence in Non-Equilibrium Boundary Layers

DTIC Science & Technology

2006-10-08

FINAL REPORT to Air Force Office of Scientific Research (AFOSR) Project Title Influence of Surface Roughness on the Second Order Transport of...large amount of research has been performed to quantify the effects of Mach number, roughness, and wall curvature on turbulent boundary layers. However...18 a) b) c) Figure 3: a) A. D. Smith high pressure storage tank. b) Morin B series actuator controlling Virgo Engineers Trunion Mounted Ball Valve. c

The PEcAn Project: Model-Data Ecoinformatics for the Observatory Era

NASA Astrophysics Data System (ADS)

Dietze, M. C.; LeBauer, D. S.; Davidson, C. D.; Desai, A. R.; Kooper, R.; McHenry, K.; Mulrooney, P.

2011-12-01

The fundamental questions about how terrestrial ecosystems will respond to climate change are straightforward and well known, yet a small number of important gaps separate the information we have gathered from the understanding required to inform policy and management. A critical gap is that no one data source provides a complete picture of the terrestrial biosphere, and therefore multiple data sources must be integrated in a sensible manner. Process-based models represent an ideal framework for this synthesis, but to date model-data synthesize has only made use of a subset of the available data types, and remains inaccessible to much of the scientific community, largely due to the daunting ecoinformatics challenges. The Predictive Ecosystem Analyzer (PEcAn) is an open-source scientific workflow system and ecoinformatics toolbox that manages the flow of information in and out of regional-scale terrestrial biosphere models, facilitates formal data assimilation, and enables more effective feedbacks between models and field research. PEcAn makes complex analyses transparent, repeatable, and accessible to a diverse array of researchers. PEcAn is not model specific, but rather encapsulates any ecosystem model within a set of standardized input and output modules. Herein we demonstrate PEcAn's ability to automate many of the tasks involved in modeling by gathering and processing a diverse arrays of data sets, initiating ensembles of model runs, visualizing output, and comparing models to observations. PEcAn employs a fully Bayesian approach to model parameterization and the estimation of ecosystem pools and fluxes that allows a straightforward propagation of uncertainties into analyses and forecasts. This approach also makes possible the synthesis of a diverse array of data types operating at different spatial and temporal scales and to easily update predictions as new information becomes available. We also demonstrate PEcAn's ability to iteratively synthesize information for literature trait databases, ground observations, eddy-covariance towers and quantify the reductions in overall uncertainty as each new dataset is added. PEcAn also automates a number of model analyses, such as sensitivity analyses, ensemble prediction, and variance decomposition which collectively allow the system to partition and ascribe uncertainties to different model parameters and processes. PEcAn provides a direct feedback to field research by further automating the estimation of sample sizes and sampling distributions required to reduce model uncertainties, enabling further measurements to be targeted and optimized. Finally, we will present the PEcAn development plan and timeline, including new features such as the synthesis of remotely sensed data, regional-scale data assimilation, and real-time forecasting. Ultimately, PEcAn aims to make ecosystem modeling and data assimilation routine tools for answering scientific questions and informing policy and management.

Pectoral nerve block (Pecs block) with sedation for breast conserving surgery without general anesthesia

PubMed Central

Moon, Eun-Jin; Kim, Seung-Beom; Chung, Jun-Young; Song, Jeong-Yoon

2017-01-01

Most regional anesthesia in breast surgeries is performed as postoperative pain management under general anesthesia, and not as the primary anesthesia. Regional anesthesia has very few cardiovascular or pulmonary side-effects, as compared with general anesthesia. Pectoral nerve block is a relatively new technique, with fewer complications than other regional anesthesia. We performed Pecs I and Pec II block simultaneously as primary anesthesia under moderate sedation with dexmedetomidine for breast conserving surgery in a 49-year-old female patient with invasive ductal carcinoma. Block was uneventful and showed no complications. Thus, Pecs block with sedation could be an alternative to general anesthesia for breast surgeries. PMID:28932733

[Adaptation of the picture exchange communication system in a school context].

PubMed

Almeida, Maria Amélia; Piza, Maria Helena Machado; Lamônica, Dionísa Aparecida Cusin

2005-01-01

Alternative communication. To evaluate the efficacy of the adapted Pecs and Picture Communication Symbols (PCS) in the communication of a child with cerebral palsy. The participant of this study was a 9 year and 10 months old girl, with athetoid quadriplegia. All stages of the adapted Pecs were applied (Walter, 2000), using the PCS pictures (Johnson, 1998), associated with the functional curriculum proposed by LeBlanc (1991). An experimental AB Design was used in order to test the procedures. The subject was able to pass through all of the adapted Pecs phases and to use her communication board in school activities. The adapted Pecs proved to be effective in improving the subject's communication abilities.

Fracturing fluid cleanup by controlled release of enzymes from polyelectrolyte complex nanoparticles

NASA Astrophysics Data System (ADS)

Barati Ghahfarokhi, Reza

Guar-based polymer gels are used in the oil and gas industry to viscosify fluids used in hydraulic fracturing of production wells, in order to reduce leak-off of fluids and pressure, and improve the transport of proppants. After fracturing, the gel and associated filter cake must be degraded to very low viscosities using breakers to recover the hydraulic conductivity of the well. Enzymes are widely used to achieve this but injecting high concentrations of enzyme may result in premature degradation, or failure to gel; denaturation of enzymes at alkaline pH and high temperature conditions can also limit their applicability. In this study, application of polyelectrolyte nanoparticles for entrapping, carrying, releasing and protecting enzymes for fracturing fluids was examined. The objective of this research is to develop nano-sized carriers capable of carrying the enzymes to the filter cake, delaying the release of enzyme and protecting the enzyme against pH and temperature conditions inhospitable to native enzyme. Polyethylenimine-dextran sulfate (PEI-DS) polyelectrolyte complexes (PECs) were used to entrap two enzymes commonly used in the oil industry in order to obtain delayed release and to protect the enzyme from conditions inhospitable to native enzyme. Stability and reproducibility of PEC nanoparticles was assured over time. An activity measurement method was used to measure the entrapment efficiency of enzyme using PEC nanoparticles. This method was confirmed using a concentration measurement method (SDS-PAGE). Entrapment efficiencies of pectinase and a commercial high-temperature enzyme mixture in polyelectrolyte complex nanoparticles were maximized. Degradation, as revealed by reduction in viscoelastic moduli of borate-crosslinked hydroxypropyl guar (HPG) gel by commercial enzyme loaded in polyelectrolyte nanoparticles, was delayed, compared to equivalent systems where the enzyme mixture was not entrapped. This indicates that PEC nanoparticles delay the activity of enzymes by entrapping them. It was also observed that control PEC nanoparticles decreased both viscoelastic moduli, but with a slower rate compared to the PEC nanoparticles loaded with enzyme. Preparation shear and applied shear showed no significant effect on activity of enzyme-loaded PEC nanoparticles mixed with HPG solutions. However, fast addition of chemicals during the preparations showed smaller particle size compared to the drop-wise method. PEC nanoparticles (PECNPs) also protected both enzymes from denaturation at elevated temperature and pH. Following preparation, enzyme-loaded PEC nanoparticles were mixed with borate crosslinked HPG and the mixture was injected through a shear loop. Pectinase-loaded nanoparticles mixed with gelled HPG showed no sensitivity to shear applied along the shear loop at 25 °C. However, EL2X-loaded PEC nanoparticles showed sensitivity to shear applied along the shear loop at 40 °C. Filter cake was formed and degraded in a fluid loss cell for borate crosslinked HPG solutions mixed with either enzymes or enzyme-loaded PEC nanoparticles. Cleanup slopes of filter cake degraded using enzyme-loaded PEC nanoparticles and systems with enzymes mixed with HPG gel were significantly higher than for the filter cake formed with HPG gel mixed with no enzyme. In a different application, enzyme-loaded PEC nanoparticles showed significantly slower reduction in viscosity of HPG solution over time compared to the HPG systems mixed with enzyme. Increasing the viscosity of low concentration HPG, used as slick-water, decreases the proppant settling velocity. This is of specific interest in fracturing fluids used for unconventional reservoirs.

Entrainment of solid particles over irregular wavy walls

NASA Astrophysics Data System (ADS)

Milici, Barbara

2017-11-01

The distribution of inertial particles in turbulent flows is highly nonuniform and is governed by the dynamics of turbulent structures of the underlying carrier flow field which, in turn, is affected by the presence of a loading of dispersed particles. The issue is discussed here focusing on the coupling between near-bed coherent structures and suspended solid particles dynamics, in wall-bounded turbulent multiphase flows, bounded by rough boundaries. The friction Reynolds number of the unladen flow is Reτ=180 and the dispersed phase spans one order of magnitude of particle diameter. The analysis takes into account fluid-particle interaction (two-way coupling) in the frame of the Particle-Source-In-Cell (PSIC) method, using Direct Numerical Simulations (DNS) for the carrier phase coupled with Lagrangian Particle Tracking (LPT) for the dispersed phase. The effect of the wall's roughness is taken into account modelling the elastic rebound of particles onto it, instead of using a virtual rebound model.

Continuous PECS II block for postoperative analgesia in patients undergoing transapical transcatheter aortic valve implantation.

PubMed

Shakuo, Tomoharu; Kakumoto, Shinichi; Kuribayashi, Junya; Oe, Katsunori; Seo, Katsuhiro

2017-01-01

It has been reported that PECS II block can alleviate postoperative pain following transapical transcatheter aortic valve implantation (TA-TAVI). However, the effectiveness of continuous PECS II block with catheterization has not yet been reported on the postoperative pain in patients undergoing TA-TAVI. We experienced two cases of TA-TAVI who received PECS II block with catheterization to manage postoperative pain. In the first case, a bolus injection for intraoperative pain and subsequent catheterization were performed before the implantation. However, the patient developed severe pain postoperatively in spite of the continuous block due to displacement of the catheter. In the second case, a bolus injection and the catheterization for the continuous block were performed before and after the implantation, respectively, which provided high-quality pain control. Continuous PECS II block may be useful to control perioperative pain associated with TA-TAVI. The insertion of the catheter after the implantation could be useful to avoid its displacement during the surgery.

Reducing PEC uncertainty in coastal zones: a case study on carbamazepine, oxcarbazepine and their metabolites.

PubMed

Fenet, Hélène; Arpin-Pont, Lauren; Vanhoutte-Brunier, Alice; Munaron, Dominique; Fiandrino, Annie; Martínez Bueno, Maria-Jesus; Boillot, Clotilde; Casellas, Claude; Mathieu, Olivier; Gomez, Elena

2014-07-01

Concentrations of the antiepileptic drugs carbamazepine (Cbz), oxcarbazepine (OxCz) and their main metabolites were predicted in a wastewater treatment plant (WTP) and in the vicinity of its submarine outfall located in a Mediterranean coastal zone. Refined predicted environmental concentrations (PECs) were calculated in effluents based on consumption data and human excretion rates. PECs were estimated in the sea using the hydrodynamic MARS 3D model integrating meteorological data, oceanic conditions (wind, tide, atmospheric pressure), freshwater and sewage inputs. Measured environmental concentrations (MECs) were compared to PECs to assess the estimation relevance. In the coastal zone, PEC and MEC were in the same magnitude range. Modeling of Cbz diffusion and advection just above the submarine outfall showed the influence of the thermocline during summer, with low diffusion of Cbz from the bottom to the surface. This work allowed understanding the dispersion of target compounds and deserved further development for a better acknowledgement of vulnerability at local scales. Copyright © 2014 Elsevier Ltd. All rights reserved.

A photoelectrochemical (PEC) study on graphene oxide based hematite thin films heterojunction (R-GO/Fe2O3)

NASA Astrophysics Data System (ADS)

Sharma, Poonam; Zachariah, Michael; Ehrman, Sheryl; Shrivastava, Rohit; Dass, Sahab; Satsangi, Vibha; Michael Zachariah, Sheryl Ehrman Collaboration; Rohit Shrivastava, Sahab Dass Collaboration; Vibha R Satsangi, Poonam Sharma Team

2013-03-01

Graphene has an excellent electronic conductivity, a high theoretical surface area of 2630 m2/g and excellent mechanical properties and, thus, is a promising component for high-performance electrode materials. Following this, GO has been used to modify the PEC response of photoactive material hematite thin films in PEC cell. A reduced graphene oxide/iron oxide (R-GO/Fe2O3) thin film structure has been successfully prepared on ITO by directly growing iron oxide particles on the thermally reduced graphene oxide sheets prepared from suspension of exfoliated graphene oxide. R-GO/Fe2O3 thin films were tested in PEC cell and offered ten times higher photocurrent density than pristine Fe2O3 thin film sample. XRD, SEM, EDS, UV-Vis, Mott-Schottky and Raman studies were carried out to study spectro-electrochemical properties. Enhanced PEC performance of these photoelectrodes was attributed to its porous morphology, improved conductivity upon favorable carrier transfer across the oxides interface.

Influence of in-hole roughness and high freestream turbulence on film cooling from a shaped hole

NASA Astrophysics Data System (ADS)

Schroeder, Robert P.

Gas turbines are heavily used for electricity generation and aircraft propulsion with a strong desire in both uses to maximize thermal efficiency while maintaining reasonable power output. As a consequence, gas turbines run at high turbine inlet temperatures that require sophisticated cooling technologies to ensure survival of turbine components. One such technology is film cooling with shaped holes, where air is withdrawn from latter stages of the compressor, is bypassed around the combustor, and is eventually ejected out holes in turbine component surfaces. Air ejected from these shaped holes helps maintain components at temperatures lower than flow from the combustor. Many studies have investigated different factors that influence shaped hole performance. However, no studies in open literature have investigated how cooling performance is affected by roughness along interior walls of the shaped hole. The effect of in-hole roughness on shaped hole film cooling was the focus of this research. Investigation of in-hole roughness effects first required the determination of behavior for a shaped hole with smooth walls. A public shaped hole, now used by other investigators as well, was designed with a diffused outlet having 7º expansion angles and an area ratio of 2.5. At low freestream turbulence intensity of 0.5%, film cooling adiabatic effectiveness for this smooth hole was found to peak at a blowing ratio of 1.5. Measurements of flowfields and thermal fields revealed causes of this behavior. Blowing ratio increases above 1.5 caused the jet from the smooth hole to penetrate higher into the surrounding mainstream, exhibit a stronger counter-rotating vortex pair, and have narrower contact with the wall than at lower blowing ratios. Experiments performed at high freestream turbulence intensity of 13% revealed dynamics of how freestream turbulence both diluted and laterally spread coolant. At the high blowing ratio of 3 the dilution and spreading were competing effects, such that elevated freestream turbulence did not cause a decrease in area-averaged effectiveness. At the blowing ratio of 1.5, high freestream turbulence caused area-averaged effectiveness to decrease 17% relative to the low freestream turbulence case. Film cooling performance was measured for the shaped hole geometry with several different configurations of in-hole roughness. At low freestream turbulence intensity, in hole roughness caused decreases in area-averaged adiabatic effectiveness up to 61% relative to the smooth hole performance. These percent decreases in adiabatic effectiveness were more severe with increasing roughness levels and with increasing blowing ratios. Flowfield and thermal field measurements for the configuration with largest roughness size showed that the decrease in adiabatic effectiveness for rough holes as compared to smooth holes was due to thicker boundary layers along the interior walls of the cooling holes. The thicker boundary layers resulted in faster jet core flow, which in turn caused increased penetration of coolant into the mainstream and increased turbulence intensity inside the jet, with both leading to reduced adiabatic effectiveness. Detrimental effects of in-hole roughness persisted at the high freestream turbulence conditions as well.

Photocatalytic and Photoelectrochemically Degradation of Chlorsulfuron herbicide

NASA Astrophysics Data System (ADS)

Guo, Xu; Liu, Hongwei; Miao, Jinjie; Ma, Zhen

2017-12-01

Photocatalytic and photo electrochemical (PEC) degradation of chlorsulfuron herbicide were studied. Two novel PEC electrodes Ti/IrO2-Pt-WO3 (TIW) and Ti/IrO2-Pt-Ag3PO4 (TIA) were designed and some important factors were studied. Lower current density showed lower removal efficiency than higher conditions by electrochemical method. Furthermore, PEC showed higher degradation efficiency than the sum of individual EO and photocatalytic methode.

Effect of treated sunflower meal with tannin extracted from pistachio hulls on in vitro gas production and ruminal fermentation

PubMed Central

Jolazadeh, Alireza; Mohammadabadi, Tahereh

2017-01-01

This experiment was conducted to study the effects of various amounts of treated sunflower meal (SFM) with extracted tannins from pistachio hulls on in vitro gas production and ruminal fermentation in ruminants. The SFM was treated with pistachio extract concentrate (PEC), which contained 111.40 g kg-1 total phenol and 71.30 g kg-1 total tannin per dry matter of extract, at six experimental treatment levels of 0, 7, 14, 21, 28 and 35 g PEC per 100 g SFM on a dry matter basis. In vitro gas production, in vitro organic matter digestibility (IVOMD), metabolizable energy (ME) and fermentative parameters of samples were measured. The PEC had no effect on fermentation rate, but asymptotic gas production was linearly decreased with increasing dose of extract. All fermentation parameters (i.e., apparent degraded substrate, short chain fatty acids, gas yield at 24 hr, partitioning factor at 96 hr, IVOMD, ME and microbial protein production (MP) linearly decreased with increasing PEC treatment. Inclusion of PEC linearly decreased ruminal ammonia nitrogen concentration (NH3-N), total protozoa population and pH in the all incubation times. In conclusion, the addition of PEC positively modified some rumen parameters such as NH3-N concentration and protozoa population. PMID:29085607

Positive emotion communication: Fostering well-being at end of life.

PubMed

Terrill, Alexandra L; Ellington, Lee; John, Kevin K; Latimer, Seth; Xu, Jiayun; Reblin, Maija; Clayton, Margaret F

2018-04-01

Little is known about positive emotion communication (PEC) in end-of-life care. This study aims to identify types and patterns of PEC among hospice nurses, caregivers, and patients. A coding system based on positive psychology theory was applied as a secondary analysis to audio recordings of hospice nurse home visits with cancer patients and family caregivers, collected as part of a prospective longitudinal study. Eighty recordings (4 visits from 20 triads) were coded for humor, connection, praise, positive focus, gratitude, taking joy/savoring, and perfunctory statements. Descriptive statistics revealed the greatest proportion of PEC was made by nurses. Humor was most frequently used across all speakers. Cluster analysis revealed four PEC visit types: Savor/Take Joy; Humor; Perfunctory; and Other-focused Expressions of Positive Emotions. Linear mixed effect regression was used to estimate the trajectory of PEC over time, but no significant change was found. We found that positive emotions are common in nurse, caregiver and patient communication at end-of-life and do not decline closer to death. This study is among the first to explore PEC at end-of-life, and offers a way to bring strengths-based approaches into end of life communication research. Copyright © 2017 Elsevier B.V. All rights reserved.

Modeling of surface roughness effects on Stokes flow in circular pipes

NASA Astrophysics Data System (ADS)

Song, Siyuan; Yang, Xiaohu; Xin, Fengxian; Lu, Tian Jian

2018-02-01

Fluid flow and pressure drop across a channel are significantly influenced by surface roughness on a channel wall. The present study investigates the effects of periodically structured surface roughness upon flow field and pressure drop in a circular pipe at low Reynolds numbers. The periodic roughness considered exhibits sinusoidal, triangular, and rectangular morphologies, with the relative roughness (i.e., ratio of the amplitude of surface roughness to hydraulic diameter of the pipe) no more than 0.2. Based upon a revised perturbation theory, a theoretical model is developed to quantify the effect of roughness on fully developed Stokes flow in the pipe. The ratio of static flow resistivity and the ratio of the Darcy friction factor between rough and smooth pipes are expressed in four-order approximate formulations, which are validated against numerical simulation results. The relative roughness and the wave number are identified as the two key parameters affecting the static flow resistivity and the Darcy friction factor.

Macrophage Migration Inhibitory Factor Mediates Proliferative GN via CD74

PubMed Central

Djudjaj, Sonja; Lue, Hongqi; Rong, Song; Papasotiriou, Marios; Klinkhammer, Barbara M.; Zok, Stephanie; Klaener, Ole; Braun, Gerald S.; Lindenmeyer, Maja T.; Cohen, Clemens D.; Bucala, Richard; Tittel, Andre P.; Kurts, Christian; Moeller, Marcus J.; Floege, Juergen; Ostendorf, Tammo

2016-01-01

Pathologic proliferation of mesangial and parietal epithelial cells (PECs) is a hallmark of various glomerulonephritides. Macrophage migration inhibitory factor (MIF) is a pleiotropic cytokine that mediates inflammation by engagement of a receptor complex involving the components CD74, CD44, CXCR2, and CXCR4. The proliferative effects of MIF may involve CD74 together with the coreceptor and PEC activation marker CD44. Herein, we analyzed the effects of local glomerular MIF/CD74/CD44 signaling in proliferative glomerulonephritides. MIF, CD74, and CD44 were upregulated in the glomeruli of patients and mice with proliferative glomerulonephritides. During disease, CD74 and CD44 were expressed de novo in PECs and colocalized in both PECs and mesangial cells. Stress stimuli induced MIF secretion from glomerular cells in vitro and in vivo, in particular from podocytes, and MIF stimulation induced proliferation of PECs and mesangial cells via CD74. In murine crescentic GN, Mif-deficient mice were almost completely protected from glomerular injury, the development of cellular crescents, and the activation and proliferation of PECs and mesangial cells, whereas wild-type mice were not. Bone marrow reconstitution studies showed that deficiency of both nonmyeloid and bone marrow–derived Mif reduced glomerular cell proliferation and injury. In contrast to wild-type mice, Cd74-deficient mice also were protected from glomerular injury and ensuing activation and proliferation of PECs and mesangial cells. Our data suggest a novel molecular mechanism and glomerular cell crosstalk by which local upregulation of MIF and its receptor complex CD74/CD44 mediate glomerular injury and pathologic proliferation in GN. PMID:26453615

Changes in glomerular parietal epithelial cells in mouse kidneys with advanced age

PubMed Central

Roeder, Sebastian S.; Stefanska, Ania; Eng, Diana G.; Kaverina, Natalya; Sunseri, Maria W.; McNicholas, Bairbre A.; Rabinovitch, Peter; Engel, Felix B.; Daniel, Christoph; Amann, Kerstin; Lichtnekert, Julia; Pippin, Jeffrey W.

2015-01-01

Kidney aging is accompanied by characteristic changes in the glomerulus, but little is known about the effect of aging on glomerular parietal epithelial cells (PECs), nor if the characteristic glomerular changes in humans and rats also occur in very old mice. Accordingly, a descriptive analysis was undertaken in 27-mo-old C57B6 mice, considered advanced age. PEC density was significantly lower in older mice compared with young mice (aged 3 mo), and the decrease was more pronounced in juxtamedullary glomeruli compared with outer cortical glomeruli. In addition to segmental and global glomerulosclerosis in older mice, staining for matrix proteins collagen type IV and heparan sulfate proteoglycan were markedly increased in Bowman's capsules of older mouse glomeruli, consistent with increased extracellular matrix production by PECs. De novo staining for CD44, a marker of activated and profibrotic PECs, was significantly increased in aged glomeruli. CD44 staining was more pronounced in the juxtamedullary region and colocalized with phosphorylated ERK. Additionally, a subset of aged PECs de novo expressed the epithelial-to-mesenchymal transition markers α-smooth muscle and vimentin, with no changes in epithelial-to-mesenchymal transition markers E-cadherin and β-catenin. The mural cell markers neural/glial antigen 2, PDGF receptor-β, and CD146 as well as Notch 3 were also substantially increased in aged PECs. These data show that mice can be used to better understand the aging kidney and that PECs undergo substantial changes, especially in juxtamedullary glomeruli, that may participate in the overall decline in glomerular structure and function with advancing age. PMID:26017974

The Regenerative Potential of Parietal Epithelial Cells in Adult Mice

PubMed Central

Berger, Katja; Schulte, Kevin; Boor, Peter; Kuppe, Christoph; van Kuppevelt, Toin H.; Floege, Jürgen; Smeets, Bart

2014-01-01

Previously, we showed that some podocytes in juvenile mice are recruited from cells lining Bowman’s capsule, suggesting that parietal epithelial cells (PECs) are a progenitor cell population for podocytes. To investigate whether PECs also replenish podocytes in adult mice, PECs were genetically labeled in an irreversible fashion in 5-week-old mice. No significant increase in labeled podocytes was observed, even after 18 months. To accelerate a potential regenerative mechanism, progressive glomerular hypertrophy was induced by progressive partial nephrectomies. Again, no significant podocyte replenishment was observed. Rather, labeled PECs exclusively invaded segments of the tuft affected by glomerulosclerosis, consistent with our previous findings. We next reassessed PEC recruitment in juvenile mice using a different reporter mouse and confirmed significant recruitment of labeled PECs onto the glomerular tuft. Moreover, some labeled cells on Bowman’s capsule expressed podocyte markers, and cells on Bowman’s capsule were also directly labeled in juvenile podocyte-specific Pod-rtTA transgenic mice. In 6-week-old mice, however, cells on Bowman’s capsule no longer expressed podocyte-specific markers. Similarly, in human kidneys, some cells on Bowman’s capsule expressed the podocyte marker synaptopodin from 2 weeks to 2 years of age but not at 7 years of age. In summary, podocyte regeneration from PECs could not be detected in aging mice or models of glomerular hypertrophy. We propose that a small fraction of committed podocytes reside on Bowman’s capsule close to the vascular stalk and are recruited onto the glomerular tuft during infancy to adolescence in mice and humans. PMID:24408873

The genome sequence of avian pathogenic Escherichia coli strain O1:K1:H7 shares strong similarities with human extraintestinal pathogenic E. coli genomes.

PubMed

Johnson, Timothy J; Kariyawasam, Subhashinie; Wannemuehler, Yvonne; Mangiamele, Paul; Johnson, Sara J; Doetkott, Curt; Skyberg, Jerod A; Lynne, Aaron M; Johnson, James R; Nolan, Lisa K

2007-04-01

Escherichia coli strains that cause disease outside the intestine are known as extraintestinal pathogenic E. coli (ExPEC) and include human uropathogenic E. coli (UPEC) and avian pathogenic E. coli (APEC). Regardless of host of origin, ExPEC strains share many traits. It has been suggested that these commonalities may enable APEC to cause disease in humans. Here, we begin to test the hypothesis that certain APEC strains possess potential to cause human urinary tract infection through virulence genotyping of 1,000 APEC and UPEC strains, generation of the first complete genomic sequence of an APEC (APEC O1:K1:H7) strain, and comparison of this genome to all available human ExPEC genomic sequences. The genomes of APEC O1 and three human UPEC strains were found to be remarkably similar, with only 4.5% of APEC O1's genome not found in other sequenced ExPEC genomes. Also, use of multilocus sequence typing showed that some of the sequenced human ExPEC strains were more like APEC O1 than other human ExPEC strains. This work provides evidence that at least some human and avian ExPEC strains are highly similar to one another, and it supports the possibility that a food-borne link between some APEC and UPEC strains exists. Future studies are necessary to assess the ability of APEC to overcome the hurdles necessary for such a food-borne transmission, and epidemiological studies are required to confirm that such a phenomenon actually occurs.

A New Water-Soluble Nanomicelle Formed through Self-Assembly of Pectin-Curcumin Conjugates: Preparation, Characterization, and Anticancer Activity Evaluation.

PubMed

Bai, Feng; Diao, Jiajing; Wang, Ying; Sun, Shixin; Zhang, Hongmei; Liu, Yunyun; Wang, Yanqing; Cao, Jian

2017-08-16

Curcumin is a dominating active component of Curcuma longa and has been studied widely because of its prominent biological activities. The extremely low aqueous solubility, stability, and bioavailability of curcumin limit its application in the field of medicine. In this study, we developed pectin-curcumin (PEC-CCM) conjugates that could self-assemble water-soluble nanomicelles in aqueous solution. The structure of PEC-CCM conjugates was characterized by ultraviolet-visible spectra, fluorescence spectra, Fourier transform infrared spectroscopy, and 1 H nuclear magnetic resonance spectroscopy. The thermal property of PEC-CCM conjugates was investigated by thermogravimetric analysis. It was found that PEC-CCM conjugates had formed nanomicelles in aqueous medium via self-assembly. These nanomicelles were observed as small spheres or ellipsoids and aggregated with a size range of 70-190 nm by transmission electron microscopy analysis. In a solution of nanomicelles, the stability of curcumin was improved, and its antioxidant property was preserved. The anticancer activity of PEC-CCM conjugates was quantified by the MTT [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] assay using a hepatic cancer cell line (HepG2), a breast cancer cell line (MCF-7), a cervical cancer cell line (HeLa), and a human normal kidney cell line (293A). It was found that the curcumin of PEC-CCM conjugates had a more significant inhibitory effect on cancer cells and was less cytotoxic to normal cells than free curcumin was. PEC-CCM conjugates have great potential for some food and pharmaceutical applications.

Heterozygous Null Bone Morphogenetic Protein Receptor Type 2 Mutations Promote SRC Kinase-dependent Caveolar Trafficking Defects and Endothelial Dysfunction in Pulmonary Arterial Hypertension*

PubMed Central

Prewitt, Allison R.; Ghose, Sampa; Frump, Andrea L.; Datta, Arumima; Austin, Eric D.; Kenworthy, Anne K.; de Caestecker, Mark P.

2015-01-01

Hereditary pulmonary arterial hypertension (HPAH) is a rare, fatal disease of the pulmonary vasculature. The majority of HPAH patients inherit mutations in the bone morphogenetic protein type 2 receptor gene (BMPR2), but how these promote pulmonary vascular disease is unclear. HPAH patients have features of pulmonary endothelial cell (PEC) dysfunction including increased vascular permeability and perivascular inflammation associated with decreased PEC barrier function. Recently, frameshift mutations in the caveolar structural protein gene Caveolin-1 (CAV-1) were identified in two patients with non-BMPR2-associated HPAH. Because caveolae regulate endothelial function and vascular permeability, we hypothesized that defects in caveolar function might be a common mechanism by which BMPR2 mutations promote pulmonary vascular disease. To explore this, we isolated PECs from mice carrying heterozygous null Bmpr2 mutations (Bmpr2+/−) similar to those found in the majority of HPAH patients. We show that Bmpr2+/− PECs have increased numbers and intracellular localization of caveolae and caveolar structural proteins CAV-1 and Cavin-1 and that these defects are reversed after blocking endocytosis with dynasore. SRC kinase is also constitutively activated in Bmpr2+/− PECs, and localization of CAV-1 to the plasma membrane is restored after treating Bmpr2+/− PECs with the SRC kinase inhibitor 3-(4-chlorophenyl)-1-(1,1-dimethylethyl)-1H-pyrazolo[3,4-d]pyrimidin-4-amine (PP2). Late outgrowth endothelial progenitor cells isolated from HPAH patients show similar increased activation of SRC kinase. Moreover, Bmpr2+/− PECs have impaired endothelial barrier function, and barrier function is restored after treatment with PP2. These data suggest that heterozygous null BMPR2 mutations promote SRC-dependent caveolar trafficking defects in PECs and that this may contribute to pulmonary endothelial barrier dysfunction in HPAH patients. PMID:25411245

The Complete Sequence and Comparative Analysis of a Multidrug-Resistance and Virulence Multireplicon IncFII Plasmid pEC302/04 from an Extraintestinal Pathogenic Escherichia coli EC302/04 Indicate Extensive Diversity of IncFII Plasmids.

PubMed

Ho, Wing Sze; Yap, Kien-Pong; Yeo, Chew Chieng; Rajasekaram, Ganeswrie; Thong, Kwai Lin

2015-01-01

Extraintestinal pathogenic Escherichia coli (ExPEC) that causes extraintestinal infections often harbor plasmids encoding fitness traits such as resistance and virulence determinants that are of clinical importance. We determined the complete nucleotide sequence of plasmid pEC302/04 from a multidrug-resistant E. coli EC302/04 which was isolated from the tracheal aspirate of a patient in Malaysia. In addition, we also performed comparative sequence analyses of 18 related IncFIIA plasmids to determine the phylogenetic relationship and diversity of these plasmids. The 140,232 bp pEC302/04 is a multireplicon plasmid that bears three replication systems (FII, FIA, and FIB) with subtype of F2:A1:B1. The plasmid is self-transmissible with a complete transfer region. pEC302/04 also carries antibiotic resistance genes such as bla TEM-1 and a class I integron containing sul1, cml and aadA resistance genes, conferring multidrug resistance (MDR) to its host, E. coli EC302/04. Besides, two iron acquisition systems (SitABCD and IutA-IucABCD) which are the conserved virulence determinants of ExPEC-colicin V or B and M (ColV/ColBM)-producing plasmids were identified in pEC302/04. Multiple toxin-antitoxin (TA)-based addiction systems (i.e., PemI/PemK, VagC/VagD, CcdA/CcdB, and Hok/Sok) and a plasmid partitioning system, ParAB, and PsiAB, which are important for plasmid maintenance were also found. Comparative plasmid analysis revealed only one conserved gene, the repA1 as the core genome, showing that there is an extensive diversity among the IncFIIA plasmids. The phylogenetic relationship of 18 IncF plasmids based on the core regions revealed that ColV/ColBM-plasmids and non-ColV/ColBM plasmids were separated into two distinct groups. These plasmids, which carry highly diverse genetic contents, are also mosaic in nature. The atypical combination of genetic materials, i.e., the MDR- and ColV/ColBM-plasmid-virulence encoding regions in a single ExPEC plasmid is rare but of clinical importance. Such phenomenon is bothersome when the plasmids are transmissible, facilitating the spread of virulence and resistance plasmids among pathogenic bacteria. Notably, certain TA systems are more commonly found in particular ExPEC plasmid types, indicating the possible relationships between certain TA systems and ExPEC pathogenesis.

Effect of truncated cone roughness element density on hydrodynamic drag

NASA Astrophysics Data System (ADS)

Womack, Kristofer; Schultz, Michael; Meneveau, Charles

2017-11-01

An experimental study was conducted on rough-wall, turbulent boundary layer flow with roughness elements whose idealized shape model barnacles that cause hydrodynamic drag in many applications. Varying planform densities of truncated cone roughness elements were investigated. Element densities studied ranged from 10% to 79%. Detailed turbulent boundary layer velocity statistics were recorded with a two-component LDV system on a three-axis traverse. Hydrodynamic roughness length (z0) and skin-friction coefficient (Cf) were determined and compared with the estimates from existing roughness element drag prediction models including Macdonald et al. (1998) and other recent models. The roughness elements used in this work model idealized barnacles, so implications of this data set for ship powering are considered. This research was supported by the Office of Naval Research and by the Department of Defense (DoD) through the National Defense Science & Engineering Graduate Fellowship (NDSEG) Program.

Evolution of dispersion coefficient in the single rough-walled fracture before and after circulated flow near the wall

NASA Astrophysics Data System (ADS)

Lee, S.; Yeo, I.; Lee, K.

2012-12-01

Understanding detailed solute transport mechanism in a single fracture is required to expand it to the complex fractured medium. Dispersion in the variable-aperture fractures occurs by combined effects of molecular diffusion, macro dispersion and Taylor dispersion. It has been reported that Taylor dispersion which is proportional to the square of the velocity dominates for the high velocity, while macro dispersion is proportional to the velocity. Contributions of each scheme are different as the velocity changes. To investigate relationship between Reynolds number and dispersion coefficient, single acrylic rough-walled fracture which has 20 cm length and 1.03 mm average aperture was designed. In this experiment, dispersion coefficient was calculated at the middle of the fracture and at the edge of the fracture via moment analysis using breakthrough curve (BTC) of fluorescent solute under the Reynolds number 0.08, 0.28, 2.78, 8.2 and 16.4. In the results, distinct dispersion regime was observed at the highly rough-walled fracture, which is inconsistent with the model that was suggested by previous research. In the range of Re < 2.78, the dispersion coefficient was proportional to the power of n (1 2.78. The reason of this transition zone was related to the generation of circulated flow near the wall. It can flush the trapped contaminant out to the main flow channel, which makes tailing effect diminished. Also, these circulation zones were visualized using microscope, CCD camera and fluorescent particles.

Characteristics of subgrid-resolved-scale dynamics in anisotropic turbulence, with application to rough-wall boundary layers

NASA Astrophysics Data System (ADS)

Juneja, Anurag; Brasseur, James G.

1999-10-01

Large-eddy simulation (LES) of the atmospheric boundary layer (ABL) using eddy viscosity subgrid-scale (SGS) models is known to poorly predict mean shear at the first few grid cells near the ground, a rough surface with no viscous sublayer. It has recently been shown that convective motions carry this localized error vertically to infect the entire ABL, and that the error is more a consequence of the SGS model than grid resolution in the near-surface inertial layer. Our goal was to determine what first-order errors in the predicted SGS terms lead to spurious expectation values, and what basic dynamics in the filtered equation for resolved scale (RS) velocity must be captured by SGS models to correct the deficiencies. Our analysis is of general relevance to LES of rough-wall high Reynolds number boundary layers, where the essential difficulty in the closure is the importance of the SGS acceleration terms, a consequence of necessary under-resolution of relevant energy-containing motions at the first few grid levels, leading to potentially strong couplings between the anisotropies in resolved velocity and predicted SGS dynamics. We analyze these two issues (under-resolution and anisotropy) in the absence of a wall using two direct numerical simulation datasets of homogeneous turbulence with very different anisotropic structure characteristic of the near-surface ABL: shear- and buoyancy-generated turbulence. We uncover three important issues which should be addressed in the design of SGS closures near rough walls and we provide a priori tests for the SGS model. First, we identify a strong spurious coupling between the anisotropic structure of the resolved velocity field and predicted SGS dynamics which can create a feedback loop to incorrectly enhance certain components of the predicted velocity field. Second, we find that eddy viscosity and "similarity" SGS models do not contain enough degrees of freedom to capture, at a sufficient level of accuracy, both RS-SGS energy flux and SGS-RS dynamics. Third, to correctly capture pressure transport near a wall, closures must be made more flexible to accommodate proper partitioning between SGS stress divergence and SGS pressure gradient.

Formation of different micro-morphologies from VO2 and ZnO crystallization using macro-porous silicon substrates

NASA Astrophysics Data System (ADS)

Salazar-Kuri, U.; Antúnez, E. E.; Estevez, J. O.; Olive-Méndez, Sion F.; Silva-González, N. R.; Agarwal, V.

2017-05-01

Square-shaped macropores produced by electrochemical anodization of n- and p-type Si wafers have been used as centers of nucleation to crystallize VO2 and ZnO. Substrate roughness dependent formation of different morphologies is revealed in the form of squared particles, spheres, bars and ribbons in the case of VO2 and hexagonal piles and spheres in the case of ZnO, have been observed.The presence of nano-/micro-metric crystals was studied through field emission scanning electron microscopy and energy dispersive X-ray spectroscopy mapping. Crystal structure of metal oxides was confirmed by micro-Raman spectroscopy. The growth of the different morphologies has been explained in terms of the surface free energy of a bare Si/SiO2 substrate and its modification originated from the roughness of the surface and of the walls of the porous substrates. This energy plays a crucial role on the minimization of the required energy to induce heterogeneous nucleation and crystal growth. Present work strengthens and provides an experimental evidence of roughness dependent metal oxide crystal growth with well-defined habits from pore corners and rough sides of the pore walls, similar to already reported protein crystals.

Ultrafast Time-Resolved Photoluminescence Studies of Gallium-Arsenide

NASA Astrophysics Data System (ADS)

Johnson, Matthew Bruce

This thesis concerns the study of ultrafast phenomena in GaAs using time-resolved photoluminescence (PL). The thesis consists of five chapters. Chapter one is an introduction, which discusses the study of ultrafast phenomena in semiconductors. Chapter two is a description of the colliding-pulse mode-locked (CPM) ring dye laser, which is at the heart of the experimental apparatus used in this thesis. Chapter three presents a detailed experimental and theoretical investigation of photoluminescence excitation correlation spectroscopy (PECS), the novel technique which is used to time-resolve ultrafast PL phenomena. Chapters 4 and 5 discuss two applications of the PECS technique. In Chapter 4 the variation of PL intensity in In-alloyed GaAs substrate material is studied, while Chapter 5 discusses the variation of carrier lifetimes in ion-damaged GaAs used in photo-conductive circuit elements (PCEs). PECS is a pulse-probe technique that measures the cross correlation of photo-excited carrier populations. The theoretical model employed in this thesis is based upon the rate equation for a simple three-level system consisting of valence and conduction bands and a single trap level. In the limit of radiative band-to-band dominated recombination, no PECS signal should be observed; while in the capture -dominated recombination limit, the PECS signal from the band-to-band PL measures the cross correlation of the excited electron and hole populations and thus, the electron and hole lifetimes. PECS is experimentally investigated using a case study of PL in semi-insulating (SI) GaAs and In -alloyed GaAs. At 77 K, the PECS signal is characteristic of a capture-dominated system, yielding an electron-hole lifetime of about 200 ps. However, at 5 K the behavior is more complicated and shows saturation effects due to the C acceptor level, which is un-ionized at 5 K. As a first application, PECS is used to investigate the large band-to-band PL contrast observed near dislocations in In-alloyed GaAs. It is found that the PL intensity contrast between bright and dark areas correlates with the ratio of the lifetimes measured using PECS in these areas. Thus, the PL intensity contrast is due to the difference in the carrier lifetimes in the different regions. The carrier lifetimes in the bright and dark regions have different temperature dependences. (Abstract shortened with permission of author.).

Evaluation of Recombinant Attenuated Salmonella Vaccine Strains for Broad Protection against Extraintestinal Pathogenic Escherichia coli.

PubMed

Maddux, Jacob T; Stromberg, Zachary R; Curtiss Iii, Roy; Mellata, Melha

2017-01-01

Antibiotic-resistant bacterial infections are difficult to treat, producing a burden on healthcare and the economy. Extraintestinal pathogenic Escherichia coli (ExPEC) strains frequently carry antibiotic resistance genes, cause infections outside of the intestine, and are causative agents of hospital-acquired infections. Developing a prevention strategy against this pathogen is challenging due to its antibiotic resistance and antigenic diversity. E. coli common pilus (ECP) is frequently found in ExPEC strains and may serve as a common antigen to induce protection against several ExPEC serotypes. In addition, live recombinant attenuated Salmonella vaccine (RASV) strains have been used to prevent Salmonella infection and can also be modified to deliver foreign antigens. Thus, the objective of this study was to design a RASV to produce ECP on its surface and assess its ability to provide protection against ExPEC infections. To constitutively display ECP in a RASV strain, we genetically engineered a vector (pYA4428) containing aspartate-β-semialdehyde dehydrogenase and E. coli ecp genes and introduced it into RASV χ9558. RASV χ9558 containing an empty vector (pYA3337) was used as a control to assess protection conferred by the RASV strain without ECP. We assessed vaccine efficacy in in vitro bacterial inhibition assays and mouse models of ExPEC-associated human infections. We found that RASV χ9558(pYA4428) synthesized the major pilin (EcpA) and tip pilus adhesin (EcpD) on the bacterial surface. Mice orally vaccinated with RASV χ9558(pYA3337) without ECP or χ9558(pYA4428) with ECP, produced anti- Salmonella LPS and anti- E. coli EcpA and EcpD IgG and IgA antibodies. RASV strains showed protective potential against some E. coli and Salmonella strains as assessed using in vitro assays. In mouse sepsis and urinary tract infection challenge models, both vaccines had significant protection in some internal organs. Overall, this work showed that RASVs can elicit an immune response to E . coli and Salmonella antigens in some mice, provide significant protection in some internal organs during ExPEC challenge, and thus this study is a promising initial step toward developing a vaccine for prevention of ExPEC infections. Future studies should optimize the ExPEC antigens displayed by the RASV strain for a more robust immune response and enhanced protection against ExPEC infection.

Adding a PECS II block for proximal arm arteriovenous access - a randomised study.

PubMed

Quek, K H; Low, E Y; Tan, Y R; Ong, A S C; Tang, T Y; Kam, J W; Kiew, A S C

2018-05-01

Brachial plexus block is often utilised for proximal arm arteriovenous access creation. However, the medial upper arm and axilla are often inadequately anaesthetised, requiring repeated, intraoperative local anaesthetic supplementation, or conversion into general anaesthesia. We hypothesised that the addition of a PECS II block would improve anaesthesia and analgesia for proximal arm arteriovenous access surgery. In this prospective, double-blinded, randomised proof-of-concept study, 36 consenting adults with end-stage renal disease aged between 21 and 90 years received either a combined supraclavicular and PECS II block (Group PECS, n = 18), or combined supraclavicular and sham block (Group SCB, n = 18) for proximal arm arteriovenous access surgery. Primary outcome was whether patients required intraoperative local anaesthetic supplementation by the surgeon. In Group PECS, 33.3% (6/18) needed local anaesthetic supplementation vs. 100% (18/18) in Group SCB. Group SCB had three times (RR 3.0, 95% CI 1.6-5.8; P < 0.001) the risk of requiring intraoperative local anaesthetic supplementation. Group PECS required lower volume of supplemental local anaesthetic compared to Group SCB (0.0 ml, IQR 0.0-6.3 ml vs. 15.0 ml, IQR 7.4-17.8 ml; P < 0.001). Group SCB had twice [RR 2.2, 95% CI 1.1-4.4; (P = 0.019)] the risk of needing additional sedation or analgesia. There were no significant differences between the groups with respect to postoperative visual analogue scale pain scores, time to first rescue analgesia or patient satisfaction. The results suggest that adding a PECS II block to a supraclavicular block improves regional anaesthesia for patients with end-stage renal disease undergoing proximal arm arteriovenous access surgery. © 2018 The Acta Anaesthesiologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Development of in vitro models to demonstrate the ability of PecSys®, an in situ nasal gelling technology, to reduce nasal run-off and drip

PubMed Central

2013-01-01

Many of the increasing number of intranasal products available for either local or systemic action can be considered sub-optimal, most notably where nasal drip or run-off give rise to discomfort/tolerability issues or reduced/variable efficacy. PecSys, an in situ gelling technology, contains low methoxy (LM) pectin which gels due to interaction with calcium ions present in nasal fluid. PecSys is designed to spray readily, only forming a gel on contact with the mucosal surface. The present study employed two in vitro models to confirm that gelling translates into a reduced potential for drip/run-off: (i) Using an inclined TLC plate treated with a simulated nasal electrolyte solution (SNES), mean drip length [±SD, n = 10] was consistently much shorter for PecSys (1.5 ± 0.4 cm) than non-gelling control (5.8 ± 1.6 cm); (ii) When PecSys was sprayed into a human nasal cavity cast model coated with a substrate containing a physiologically relevant concentration of calcium, PecSys solution was retained at the site of initial deposition with minimal redistribution, and no evidence of run-off/drip anteriorly or down the throat. In contrast, non-gelling control was significantly more mobile and consistently redistributed with run-off towards the throat. Conclusion In both models PecSys significantly reduced the potential for run-off/drip ensuring that more solution remained at the deposition site. In vivo, this enhancement of retention will provide optimum patient acceptability, modulate drug absorption and maximize the ability of drugs to be absorbed across the nasal mucosa and thus reduce variability in drug delivery. PMID:22803832

Longitudinal dependence of the seasonal variations of the topside ionospheric and plasmaspheric electron content: observations and model results

NASA Astrophysics Data System (ADS)

Zhang, Man-Lian; Liu, Libo; Ning, Baiqi; Wan, Weixing

2016-07-01

Radio signals transmitted from GPS satellite going through the ionization zone above the Earth will be refracted by the ionized components in the ionosphere and the plasmasphere, which would produce additional transfer delay and generate extra errors in satellite navigation and positioning, etc. These errors have strong relation with the total electron content (TEC) along the signal's travelling path. Therefore TEC is one of the most important parameters required by many users for different modern usage purposes. The topside ionospheric and plasmaspheric electron content makes a large contribution to TEC. In the present study, data for the year 2008 of the topside ionospheric and plasmaspheric electron content (PEC) between the height of 800-20200km above the Earth derived from the upward-looking TEC measurements of the precise orbit determination antenna on board the COSMIC low Earth orbit (LEO) satellites to the GPS signals are used to study the longitudinal dependence of the seasonal variations of PEC. A comparison study of the observed PEC with the IZMIRAN_Plas model results is also made. Our study showed that PEC shows different seasonal variations at different longitudinal sectors: for the 240°E-60°E longitudinal sector, PEC shows a strong annual variation with lowest value in the June solstice and highest value in the December solstice months; In contrast, very weak seasonal variations are observed for PEC at 60°E-240°E longitudinal sector; Comparison study showed that this longitudinal dependence feature of the observed PEC's seasonal variation is not well captured by the IZMIRAN_Plas model result. Acknowledgments This research was supported by the National Natural Science Foundation of China (NSFC No. 41274163)

In vivo bioactivity of rhBMP-2 delivered with novel polyelectrolyte complexation shells assembled on an alginate microbead core template.

PubMed

Abbah, Sunny-Akogwu; Liu, Jing; Lam, Raymond W M; Goh, James C H; Wong, Hee-Kit

2012-09-10

Electrostatic interactions between polycations and polyanions are being explored to fabricate polyelectrolyte complexes (PEC) that could entrap and regulate the release of a wide range of biomolecules. Here, we report the in vivo application of PEC shells fabricated from three different polycations: poly-l-ornithine (PLO), poly-l-arginine (PLA) and DEAE-dextran (DEAE-D) to condense heparin on the surface of alginate microbeads and further control the delivery of recombinant human bone morphogenetic protein 2 (rhBMP-2) in spinal fusion application. We observed large differences in the behavior of PEC shells fabricated from the cationic polyamino acids (PLO and PLA) when compared to the cationic polysaccharide, DEAE-D. Whereas DEAE-D-based PEC shells eroded and released rhBMP-2 over 2 days in vitro, PLO- and PLA-based shells retained at least 60% of loaded rhBMP-2 after 3 weeks of incubation in phosphate-buffered saline. In vivo implantation in a rat model of posterolateral spinal fusion revealed robust bone formation in the PLO- and PLA-based PEC shell groups. This resulted in a significantly enhanced mechanical stability of the fused segments. However, bone induction and biomechanical stability of spine segments implanted with DEAE-D-based carriers were significantly inferior to both PLO- and PLA-based PEC shell groups (p<0.01). From these results, we conclude that PEC shells incorporating native heparin could be used for growth factor delivery in functional bone tissue engineering application and that PLA- and PLO-based complexes could represent superior options to DEAE-D for loading and in vivo delivery of bioactive BMP-2 in this approach. Copyright © 2012 Elsevier B.V. All rights reserved.

Metagenomic analysis of sediments under seaports influence in the Equatorial Atlantic Ocean.

PubMed

Tavares, Tallita Cruz Lopes; Normando, Leonardo Ribeiro Oliveira; de Vasconcelos, Ana Tereza Ribeiro; Gerber, Alexandra Lehmkuhl; Agnez-Lima, Lucymara Fassarella; Melo, Vânia Maria Maciel

2016-07-01

Maritime ports are anthropogenic interventions capable of causing serious alterations in coastal ecosystems. In this study, we examined the benthic microbial diversity and community structure under the influence of two maritime ports, Mucuripe (MUC) and Pecém (PEC), at Equatorial Atlantic Ocean in Northeast Brazil. Those seaports differ in architecture, time of functioning, cargo handling and contamination. The microbiomes from MUC and PEC were also compared in silico to 11 other globally distributed marine microbiomes. The comparative analysis of operational taxonomic units (OTUs) retrieved by PCR-DGGE showed that MUC presents greater richness and β diversity of Bacteria and Archaea than PEC. In line with these results, metagenomic analysis showed that MUC and PEC benthic microbial communities share the main common bacterial phyla found in coastal environments, although can be distinguish by greater abundance of Cyanobacteria in MUC and Deltaproteobacteria in PEC. Both ports differed in Archaea composition, being PEC port sediments dominated by Thaumarchaeota. The microbiomes showed little divergence in their potential metabolic pathways, although shifts on the microbial taxonomic signatures involved in nitrogen and sulphur metabolic pathways were observed. The comparative analysis of different benthic marine metagenomes from Brazil, Australia and Mexico grouped them by the geographic location rather than by the type of ecosystem, although at phylum level seaport sediments share a core microbiome constituted by Proteobacteria, Cyanobacteria, Actinobacteria, Tenericuteres, Firmicutes, Bacteriodetes and Euryarchaeota. Our results suggest that multiple physical and chemical factors acting on sediments as a result of at least 60years of port operation play a role in shaping the benthic microbial communities at taxonomic level, but not at functional level. Copyright © 2016 Elsevier B.V. All rights reserved.

Escherichia coli isolates from commercial chicken meat and eggs cause sepsis, meningitis and urinary tract infection in rodent models of human infections.

PubMed

Mellata, M; Johnson, J R; Curtiss, R

2018-02-01

The zoonotic potential of Escherichia coli from chicken-source food products is important to define for public health purposes. Previously, genotypic and phenotypic screening of E. coli isolates from commercial chicken meat and shell eggs identified some E. coli strains that by molecular criteria resembled human-source extraintestinal pathogenic E. coli (ExPEC). Here, to clarify the zoonotic risk of such chicken-source E. coli, we compared selected E. coli isolates from chicken meat and eggs, stratified by molecularly defined ExPEC status, to human-source ExPEC and to laboratory E. coli for virulence in rodent models of sepsis, meningitis and UTI, and evaluated whether specific bacterial characteristics predict experimental virulence. Multiple chicken-source E. coli resembled human-source ExPEC in their ability to cause one or multiple different ExPEC-associated infections. Swimming ability corresponded with urovirulence, K1 capsule corresponded with ability to cause neonatal meningitis, and biofilm formation in urine corresponded with ability to cause sepsis. In contrast, molecularly defined ExPEC status and individual genotypic traits were uncorrelated with ability to cause sepsis, and neither complement sensitivity nor growth in human urine corresponded with virulence in any infection model. These findings establish that chicken-derived food products contain E. coli strains that, in rodent models of multiple human-associated ExPEC infections, are able to cause disease comparably to human-source E. coli clinical isolates, which suggests that they may pose a significant food safety threat. Further study is needed to define the level of risk they pose to human health, which if appreciable would justify efforts to monitor for and reduce or eliminate them. © 2017 Blackwell Verlag GmbH.

A brief review of models of DC-DC power electronic converters for analysis of their stability

NASA Astrophysics Data System (ADS)

Siewniak, Piotr; Grzesik, Bogusław

2014-10-01

A brief review of models of DC-DC power electronic converters (PECs) is presented in this paper. It contains the most popular, continuous-time and discrete-time models used for PEC simulation, design, stability analysis and other applications. Both large-signal and small-signal models are considered. Special attention is paid to models that are used in practice for the analysis of the global and local stability of PECs.

A previously unrecognized role of C3a in proteinuric progressive nephropathy

PubMed Central

Morigi, Marina; Locatelli, Monica; Rota, Cinzia; Buelli, Simona; Corna, Daniela; Rizzo, Paola; Abbate, Mauro; Conti, Debora; Perico, Luca; Longaretti, Lorena; Benigni, Ariela; Zoja, Carlamaria; Remuzzi, Giuseppe

2016-01-01

Podocyte loss is the initial event in the development of glomerulosclerosis, the structural hallmark of progressive proteinuric nephropathies. Understanding mechanisms underlying glomerular injury is the key challenge for identifying novel therapeutic targets. In mice with protein-overload induced by bovine serum albumin (BSA), we evaluated whether the alternative pathway (AP) of complement mediated podocyte depletion and podocyte-dependent parietal epithelial cell (PEC) activation causing glomerulosclerosis. Factor H (Cfh−/−) or factor B-deficient mice were studied in comparison with wild-type (WT) littermates. WT+BSA mice showed podocyte depletion accompanied by glomerular complement C3 and C3a deposits, PEC migration to capillary tuft, proliferation, and glomerulosclerosis. These changes were more prominent in Cfh−/− +BSA mice. The pathogenic role of AP was documented by data that factor B deficiency preserved glomerular integrity. In protein-overload mice, PEC dysregulation was associated with upregulation of CXCR4 and GDNF/c-Ret axis. In vitro studies provided additional evidence of a direct action of C3a on proliferation and CXCR4-related migration of PECs. These effects were enhanced by podocyte-derived GDNF. In patients with proteinuric nephropathy, glomerular C3/C3a paralleled PEC activation, CXCR4 and GDNF upregulation. These results indicate that mechanistically uncontrolled AP complement activation is not dispensable for podocyte-dependent PEC activation resulting in glomerulosclerosis. PMID:27345360

Expression of a novel stress-inducible protein, sestrin 2, in rat glomerular parietal epithelial cells

PubMed Central

Hamatani, Hiroko; Sakairi, Toru; Takahashi, Satoshi; Watanabe, Mitsuharu; Maeshima, Akito; Ohse, Takamoto; Pippin, Jeffery W.; Shankland, Stuart J.; Nojima, Yoshihisa

2014-01-01

Sestrin 2, initially identified as a p53 target protein, accumulates in cells exposed to stress and inhibits mammalian target of rapamycin (mTOR) signaling. In normal rat kidneys, sestrin 2 was selectively expressed in parietal epithelial cells (PECs), identified by the marker protein gene product 9.5. In adriamycin nephropathy, sestrin 2 expression decreased in PECs on day 14, together with increased expression of phosphorylated S6 ribosomal protein (P-S6RP), a downstream target of mTOR. Sestrin 2 expression was markedly decreased on day 42, coinciding with glomerulosclerosis and severe periglomerular fibrosis. In puromycin aminonucleoside nephropathy, decreased sestrin 2 expression, increased P-S6RP expression, and periglomerular fibrosis were observed on day 9, when massive proteinuria developed. These changes were transient and nearly normalized by day 28. In crescentic glomerulonephritis, sestrin 2 expression was not detected in cellular crescents, whereas P-S6RP increased. In conditionally immortalized cultured PECs, the forced downregulation of sestrin 2 by short hairpin RNA resulted in increased expression of P-S6RP and increased apoptosis. These data suggest that sestrin 2 is involved in PEC homeostasis by regulating the activity of mTOR. In addition, sestrin 2 could be a novel marker of PECs, and decreased expression of sestrin 2 might be a marker of PEC injury. PMID:25056347

Minute perivascular epithelioid cell (PEC) nests in the abdominal lymph nodes--a putative precursor of PEComa.

PubMed

Nagasaka, Toru; Murakami, Yoshiko; Sasaki, Eiichi; Hosoda, Waki; Nakanishi, Toru; Yatabe, Yasushi

2015-04-01

A perivascular epithelioid cell tumor (PEComa) is a peculiar growth defined as a mesenchymal tumor composed of histologically and immunohistochemically distinct perivascular epithelioid cells (PECs). Because neither normal counterparts nor precursor lesions of PEComa have been identified, we examined minute PEC nests, ranged from 0.8 mm to 10 mm, to investigate the possible origin of the PEComa. We examined a total of 80 677 para-aortic and pelvic lymph nodes that were systematically dissected from 1656 patients for gynecological malignancies. The identified lesions were confirmed immunohistochemically with multiple PEC markers, including smooth muscle actin, HMB45, melan-A, MiTF, ER and PgR. A total of 66 minute PEC nests were found in 21 patients (1.3% of the total population) with an average frequency of 3.1 lesions per patient. In cases of multiple involvement, 11 of 13 nests were located at the same level of multiple lymph node or on continuous levels. The lesions were preferentially distributed at the level of para-aortic and high pelvic lymph nodes. All nests were positive for actin and HMB45, whereas the other markers were positive with varying frequencies. The minute PEC nests may be associated with the possible normal counterpart of PEComas. © 2015 Japanese Society of Pathology and Wiley Publishing Asia Pty Ltd.

Microscopic endometrial perivascular epithelioid cell nodules: a case report with the earliest presentation of a uterine perivascular epithelioid cell tumor

PubMed Central

2012-01-01

Abstract Perivascular epithelioid cell (PEC) tumors (PEComas) are a family of related mesenchymal tumors composed of PECs which co-express melanocytic and smooth muscle markers. Although their distinctive histologic, immunohistochemical, ultrastructural, and genetic features have been clearly demonstrated, their histogenesis and normal counterpart remain largely unknown. Precursor lesions of PEComas have rarely been reported. We herein describe a tuberous sclerosis patient with microscopic PEC nodules in the endometrium of adenomyosis, pelvic endometriosis, an ovarian endometriotic cyst, and the endometrium of the uterine cavity. The nodules showed a mixture of spindle-shaped and epithelioid cells concentrically arranged around small arteries. The cells exhibited uniform nuclei, light eosinophilic cytoplasm, and immunoreactivity with HMB-45 and CD10. Some nodules revealed continuity with a PEComa in the myometrium. These findings support microscopic endometrial PEC nodules possibly being precursor lesions of uterine PEComas. The wide distribution of the nodules in the pelvis may be related to the multicentricity of PEComas in tuberous sclerosis patients. Owing to the immunoreactivity with CD10, microscopic endometrial PEC nodules may be misinterpreted as endothelial stromal cells unless melanocytic markers are stained. To the best of our knowledge, this is a case with the earliest manifestation of PEC lesions occurring in the endometrium. Virtual Slides The virtual slide(s) for this article can be found here: http://www.diagnosticpathology.diagnomx.eu/vs/9658280017862643 PMID:22937790

Microscopic endometrial perivascular epithelioid cell nodules: a case report with the earliest presentation of a uterine perivascular epithelioid cell tumor.

PubMed

Fang, Chia-Lang; Lin, Yun-Ho; Chen, Wei-Yu

2012-09-03

Perivascular epithelioid cell (PEC) tumors (PEComas) are a family of related mesenchymal tumors composed of PECs which co-express melanocytic and smooth muscle markers. Although their distinctive histologic, immunohistochemical, ultrastructural, and genetic features have been clearly demonstrated, their histogenesis and normal counterpart remain largely unknown. Precursor lesions of PEComas have rarely been reported. We herein describe a tuberous sclerosis patient with microscopic PEC nodules in the endometrium of adenomyosis, pelvic endometriosis, an ovarian endometriotic cyst, and the endometrium of the uterine cavity. The nodules showed a mixture of spindle-shaped and epithelioid cells concentrically arranged around small arteries. The cells exhibited uniform nuclei, light eosinophilic cytoplasm, and immunoreactivity with HMB-45 and CD10. Some nodules revealed continuity with a PEComa in the myometrium. These findings support microscopic endometrial PEC nodules possibly being precursor lesions of uterine PEComas. The wide distribution of the nodules in the pelvis may be related to the multicentricity of PEComas in tuberous sclerosis patients. Owing to the immunoreactivity with CD10, microscopic endometrial PEC nodules may be misinterpreted as endothelial stromal cells unless melanocytic markers are stained. To the best of our knowledge, this is a case with the earliest manifestation of PEC lesions occurring in the endometrium. Virtual slides: The virtual slide(s) for this article can be found here: http://www.diagnosticpathology.diagnomx.eu/vs/9658280017862643.

Semiconducting Organic-Inorganic Nanodots Heterojunctions: Platforms for General Photoelectrochemical Bioanalysis Application.

PubMed

Wang, Qian; Ruan, Yi-Fan; Zhao, Wei-Wei; Lin, Peng; Xu, Jing-Juan; Chen, Hong-Yuan

2018-03-20

In this study, semiconducting organic polymer dots (Pdots) and inorganic quantum dots (Qdots) were first utilized to construct the organic-inorganic nanodots heterojunction for the photoelectrochemical (PEC) bioanalysis application. Specifically, n-type CdS Qdots, p-type CdTe Qdots, and tetraphenylporphyrin (TPP)-doped poly[(9,9-dioctylfluorenyl-2,7-diyl)- co-(1,4-benzo-{2,1',3}-thiadazole)] (PFBT) Pdots were fabricated, and their energy levels, that is, their valence band (VB)/conduction band (CB) or lowest unoccupied molecular orbital (LUMO)/highest occupied molecular orbital (HOMO) values, were also determined. Then, these nanodots were integrated to construct four types of p-n and p-p organic-inorganic nanodots heterojunctions, that is, CdS Qdots/TPP-doped PFBT Pdots, TPP-doped PFBT Pdots/CdS Qdots, CdTe Qdots/TPP-doped PFBT Pdots, and TPP-doped PFBT Pdots/CdTe Qdots, on the transparent glass electrode. Upon light irradiation, four heterojunctions exhibited different PEC behaviors with some having prominent photocurrent enhancement. With the model molecule l-cysteine (l-cys) as target, the proposed PEC sensor exhibited good performances. In brief, this work presents the first semiconducting organic-inorganic nanodots heterojunction for PEC bioanalysis application, which could be easily used as a general platform for future PEC bioanalysis building. Besides, it is expected to inspire more interest in the design, development, and implementation of various organic-inorganic heterojunctions for advanced PEC bioanalysis in the future.

PECS and VOCAs to enable students with developmental disabilities to make requests: an overview of the literature.

PubMed

Lancioni, Giulio E; O'Reilly, Mark F; Cuvo, Anthony J; Singh, Nirbhay N; Sigafoos, Jeff; Didden, Robert

2007-01-01

This paper provides an overview of the literature dealing with the use of the Picture Exchange Communication System (PECS) and voice output communication aids (VOCAs) for promoting the performance of requests by students with developmental disabilities. Computerized and manual searches were carried out to identify the studies published during the last 15 years (i.e., the period between 1992 and 2006 during which PECS and VOCA approaches became popular). Thirty-seven studies were identified and then divided into three groups concerning the use of the PECS or equivalents, the use of VOCAs or equivalents, and the comparison of both these approaches, respectively. Of the 173 students involved in studies using the PECS or equivalents only three could be considered failures, while a fourth one did not progress in the program due to illness. Similarly, of the 39 students who used VOCAs or equivalents only three could be considered failures, while one was partly successful. Finally, of the 11 students involved in the comparisons between PECS and VOCAs none could be classified as a failure. The results are very encouraging but methodological concerns and the relatively limited use of the systems in terms of request items and request opportunities suggest caution. Caution may also be needed in interpreting the reported similarities between the two systems in usability and effectiveness.

The effectiveness of Picture Exchange Communication System (PECS) training for teachers of children with autism: a pragmatic, group randomised controlled trial.

PubMed

Howlin, Patricia; Gordon, R Kate; Pasco, Greg; Wade, Angie; Charman, Tony

2007-05-01

To assess the effectiveness of expert training and consultancy for teachers of children with autism spectrum disorder in the use of the Picture Exchange Communication System (PECS). Group randomised, controlled trial (3 groups: immediate treatment, delayed treatment, no treatment). 84 elementary school children, mean age 6.8 years. A 2-day PECS workshop for teachers plus 6 half-day, school-based training sessions with expert consultants over 5 months. Rates of: communicative initiations, use of PECS, and speech in the classroom; Autism Diagnostic Observation Schedule-Generic (ADOS-G) domain scores for Communication and Reciprocal Social Interaction; scores on formal language tests. Controlling for baseline age, developmental quotient (DQ) and language; rates of initiations and PECS usage increased significantly immediately post-treatment (Odds Ratio (OR) of being in a higher ordinal rate category 2.72, 95% confidence interval 1.22-6.09, p < .05 and OR 3.90 (95%CI 1.75-8.68), p < .001, respectively). There were no increases in frequency of speech, or improvements in ADOS-G ratings or language test scores. The results indicate modest effectiveness of PECS teacher training/consultancy. Rates of pupils' initiations and use of symbols in the classroom increased, although there was no evidence of improvement in other areas of communication. TREATMENT effects were not maintained once active intervention ceased.

A dynamic subgrid-scale parameterization of the effective wall stress in atmospheric boundary layer flows over multiscale, fractal-like surfaces

NASA Astrophysics Data System (ADS)

Anderson, William; Meneveau, Charles

2010-05-01

A dynamic subgrid-scale (SGS) parameterization for hydrodynamic surface roughness is developed for large-eddy simulation (LES) of atmospheric boundary layer (ABL) flow over multiscale, fractal-like surfaces. The model consists of two parts. First, a baseline model represents surface roughness at horizontal length-scales that can be resolved in the LES. This model takes the form of a force using a prescribed drag coefficient. This approach is tested in LES of flow over cubes, wavy surfaces, and ellipsoidal roughness elements for which there are detailed experimental data available. Secondly, a dynamic roughness model is built, accounting for SGS surface details of finer resolution than the LES grid width. The SGS boundary condition is based on the logarithmic law of the wall, where the unresolved roughness of the surface is modeled as the product of local root-mean-square (RMS) of the unresolved surface height and an unknown dimensionless model coefficient. This coefficient is evaluated dynamically by comparing the plane-average hydrodynamic drag at two resolutions (grid- and test-filter scale, Germano et al., 1991). The new model is tested on surfaces generated through superposition of random-phase Fourier modes with prescribed, power-law surface-height spectra. The results show that the method yields convergent results and correct trends. Limitations and further challenges are highlighted. Supported by the US National Science Foundation (EAR-0609690).

The parietal epithelial cell is crucially involved in human idiopathic focal segmental glomerulosclerosis.

PubMed

Dijkman, Henry; Smeets, Bart; van der Laak, Jeroen; Steenbergen, Eric; Wetzels, Jack

2005-10-01

Focal segmental glomerulosclerosis (FSGS) is one of the most common patterns of glomerular injury encountered in human renal biopsies. Epithelial hyperplasia, which can be prominent in FSGS, has been attributed to dedifferentiation and proliferation of podocytes. Based on observations in a mouse model of FSGS, we pointed to the role of parietal epithelial cells (PECs). In the present study we investigated the relative role of PECs and podocytes in human idiopathic FSGS. We performed a detailed study of lesions from a patient with recurrent idiopathic FSGS by serial sectioning, marker analysis and three-dimensional reconstruction of glomeruli. We have studied the expression of markers for podocytes, PECs, mesangial cells, endothelium, and myofibroblasts. We also looked at proliferation and composition of the deposited extracellular matrix (ECM). We found that proliferating epithelial cells in FSGS lesions are negative for podocyte and macrophage markers, but stain for PEC markers. The composition of the matrix deposited by these cells is identical to Bowman's capsule. Our study demonstrates that PECs are crucially involved in the pathogenesis of FSGS lesions.

Recent Advances in Photoelectrochemical Applications of Silicon Materials for Solar-to-Chemicals Conversion.

PubMed

Zhang, Doudou; Shi, Jingying; Zi, Wei; Wang, Pengpeng; Liu, Shengzhong Frank

2017-11-23

Photoelectrochemical (PEC) technology for the conversion of solar energy into chemicals requires cost-effective photoelectrodes to efficiently and stably drive anodic and/or cathodic half-reactions to complete the overall reactions for storing solar energy in chemical bonds. The shared properties among semiconducting photoelectrodes and photovoltaic (PV) materials are light absorption, charge separation, and charge transfer. Earth-abundant silicon materials have been widely applied in the PV industry, and have demonstrated their efficiency as alternative photoabsorbers for photoelectrodes. Many efforts have been made to fabricate silicon photoelectrodes with enhanced performance, and significant progress has been achieved in recent years. Herein, recent developments in crystalline and thin-film silicon-based photoelectrodes (including amorphous, microcrystalline, and nanocrystalline silicon) immersed in aqueous solution for PEC hydrogen production from water splitting are summarized, as well as applications in PEC CO 2 reduction and PEC regeneration of discharged species in redox flow batteries. Silicon is an ideal material for the cost-effective production of solar chemicals through PEC methods. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Assessing the acquisition and generalization of two mand forms with adults with severe developmental disabilities.

PubMed

Chambers, Mark; Rehfeldt, Ruth Anne

2003-01-01

The purpose of this study was to determine whether manual sign or the Picture Exchange Communication System (P.E.C.S.) (Frost and Bondy, 1994) would be more effective in teaching mand skills to adults with mental retardation in the severe and profound range. Four participants were taught to mand for four reinforcing items using both communication modalities, in an alternating treatments design. Three of four participants demonstrated criterion performance across all four mands using P.E.C.S. first. Two of those three participants later demonstrated criterion performance for the mands using manual sign. The fourth participant was removed from the study during training due to illness, but her progress indicated greater acquisition with P.E.C.S. Generalization probes conducted at participants' respective residences showed that three participants demonstrated generalization across settings using P.E.C.S., and two participants demonstrated generalization across settings using manual sign. Participants were also more likely to mand for reinforcing items not present using P.E.C.S. than using manual sign.

Cell Uptake and Validation of Novel PECs for Biomedical Applications.

PubMed

Palamà, Ilaria E; Musarò, Mariarosaria; Coluccia, Addolorata M L; D'Amone, Stefania; Gigli, Giuseppe

2011-01-01

This pilot study provides the proof of principle for biomedical application of novel polyelectrolyte complexes (PECs) obtained via electrostatic interactions between dextran sulphate (DXS) and poly(allylamine hydrochloride) (PAH). Scanning electron microscopy (SEM) and atomic force microscopy (AFM) showed that DXS/PAH polyelectrolyte complexes were Monodispersed with regular rounded-shape features and average diameters of 250 nm at 2 : 1 weight ratios of DXS/PAH. Fluorescently labelled DXS and fluorescein-isothiocyanate- (FITC-)conjugate DXS were used to follow cell uptake efficiency of PECs and biodegradability of their enzymatically degradable DXS-layers by using confocal laser scanning microscopy (CLSM). Moreover, quantitative MTT and Trypan Blue assays were employed to validate PECs as feasible and safe nanoscaled carriers at single-cell level without adverse effects on metabolism and viability.

Cell Uptake and Validation of Novel PECs for Biomedical Applications

PubMed Central

Palamà, Ilaria E.; Musarò, Mariarosaria; Coluccia, Addolorata M. L.; D'Amone, Stefania; Gigli, Giuseppe

2011-01-01

This pilot study provides the proof of principle for biomedical application of novel polyelectrolyte complexes (PECs) obtained via electrostatic interactions between dextran sulphate (DXS) and poly(allylamine hydrochloride) (PAH). Scanning electron microscopy (SEM) and atomic force microscopy (AFM) showed that DXS/PAH polyelectrolyte complexes were Monodispersed with regular rounded-shape features and average diameters of 250 nm at 2 : 1 weight ratios of DXS/PAH. Fluorescently labelled DXS and fluorescein-isothiocyanate- (FITC-)conjugate DXS were used to follow cell uptake efficiency of PECs and biodegradability of their enzymatically degradable DXS-layers by using confocal laser scanning microscopy (CLSM). Moreover, quantitative MTT and Trypan Blue assays were employed to validate PECs as feasible and safe nanoscaled carriers at single-cell level without adverse effects on metabolism and viability. PMID:21876815

Molecular characterization of ESBL-producing Escherichia coli isolates from hospital- and community-acquired infections in NW Mexico.

PubMed

Miranda-Romero, Ana Laura; Silva-Sanchez, Jesus; Garza-Ramos, Ulises; Barrios, Humberto; Sánchez-Pérez, Alejandro; Reyna-Flores, Fernando

2017-01-01

We investigated the molecular characteristics of ESBL-producing E. coli (ESBL-PEc) isolates from two hospitals and community settings in Ciudad Obregon, Sonora, Mexico. Between 2011 and 2014, thirty-seven ESBL-PEc isolates were collected. The major encoded ESBL was the bla CTX-M-15 gene (97%); followed by 13.5% of the bla SHV-12 gene, and 5.5% encoded the bla TLA-1 gene. The PMQR gene aac(6´)-Ib-cr was detected in 97% of the isolates and the qnrB gene, in one isolate. The ESBL-PEc isolates corresponded to phylogenetic group B2, ST131. Our results highlight the dissemination of ESBL-PEc isolates in northwest Mexico (Ciudad Obregon, Sonora). Copyright © 2016 Elsevier Inc. All rights reserved.

Comparative efficacy of the picture exchange communication system (PECS) versus a speech-generating device: effects on social-communicative skills and speech development.

PubMed

Boesch, Miriam C; Wendt, Oliver; Subramanian, Anu; Hsu, Ning

2013-09-01

The Picture Exchange Communication System (PECS) and a speech-generating device (SGD) were compared in a study with a multiple baseline, alternating treatment design. The effectiveness of these methods in increasing social-communicative behavior and natural speech production were assessed with three elementary school-aged children with severe autism who demonstrated extremely limited functional communication skills. Results for social-communicative behavior were mixed for all participants in both treatment conditions. Relatively little difference was observed between PECS and SGD conditions. Although findings were inconclusive, data patterns suggest that Phase II of the PECS training protocol is conducive to encouraging social-communicative behavior. Data for speech outcomes did not reveal any increases across participants, and no differences between treatment conditions were observed.

Occupational leg oedema is more reduced by antigraduated than by graduated stockings.

PubMed

Mosti, G; Partsch, H

2013-05-01

Elastic compression stockings exerting a progressive pressure, higher at the calf than at the ankle (progressive elastic compression stockings, PECS), have already proved to be more comfortable, easier to put on and more effective in improving venous pumping function compared to graduated compression elastic stockings (GECS). Nevertheless, PECS could have a negative effect on the prevention and treatment of oedema or even favour oedema formation. The aim of the present study was to investigate if, in normal volunteers, PECS are able to prevent leg swelling during their working shift. A total of 30 normal volunteers (14 males, 16 females aged 36.4 ± 6.6 years) staying standing or sitting during their shift were enrolled into the study. Their leg volume was measured at the beginning and at the end of their working shift on 2 consecutive days. On one day, the volunteers did not put on any stockings; on the other day, they wore GECS on one leg and PECS on the other. The difference between the leg volume measured at the end of the shift and the basal volume in the morning was called 'occupational oedema'. Interface pressure at points B1 and C was measured immediately after stockings' application and before removal. The volunteers were asked to report about difficulty of putting on the stockings and comfort during wearing time. The results were submitted to statistical analysis. The GECS and PECS groups had similar baseline leg volumes (3143 vs. 3154 ml) and occupational oedema (134 vs. 137.5 ml); after putting on the stockings, occupational oedema was reduced in both legs but the reduction was significantly greater with PECS (20 vs. 40 ml with GECS) (P < 0.05). Interface pressure at ankle level is higher with GECS both in supine and in standing position while at calf level it is higher with PECS both in supine and standing position. PECS are easier to put on and slightly more comfortable. PECS are easier to put on and more comfortable and produce a significantly higher reduction of occupational oedema compared with GECS in normal volunteers. Nevertheless leg volumetry, providing a global leg-volume evaluation, is not able to localise the oedema reduction and to assess if it occurs more in the calf or the ankle area. Theoretically, despite a global volume reduction, PECS could even promote a slight oedema formation at ankle level over-compensated by a greater oedema reduction at calf level. Further studies need to concentrate on patients with venous disease and on the local distribution of this global effect. Copyright © 2013 European Society for Vascular Surgery. Published by Elsevier Ltd. All rights reserved.

Studies of the Combined Effects of Roughness and Reynolds Number in Turbulent Boundary Layers

NASA Astrophysics Data System (ADS)

Mehdi, Faraz; Klewicki, Joseph

2010-11-01

Mehdi, Klewicki & White [Physica D 239(2010)] provide evidence from existing studies that the prevalent scheme for classifying roughness regimes is likely to be incomplete. To further pursue these findings, more data are required, and for this purpose, additional rough-wall experiments are being performed. We report on our studies of the combined roughness-Reynolds number problem conducted in a 8m long wind-tunnel. The roughness considered is the randomly distributed type and introduced in the form of 24-grit sandpaper and pea gravel. The primary measurement tool is two-component LDV. The basis of the analysis is the mean equation of dynamics. In this regard, the length scale defining where the mean dynamics become dominated by inertia is of central importance.

Characteristics of secondary flows in rough-wall turbulent boundary layers

NASA Astrophysics Data System (ADS)

Vanderwel, Christina; Ganapathisubramani, Bharathram

2015-11-01

Large-scale secondary motions consisting of counter-rotating vortices and low- and high-momentum pathways can form in boundary layers that develop over rough surfaces. We experimentally investigated the sensitivity of these secondary motions to spanwise arrangement of the roughness by studying the flow over streamwise-aligned rows of elevated roughness with systematically-varied spacing. The roughness is created with LEGO blocks mounted along the floor of the wind tunnel and Stereo-PIV is used to measure the velocity field in a cross-plane. Results show that the secondary flows are strongest when the spanwise spacing of the surface topology is comparable with the boundary layer thickness. We discuss how these results are relevant to flows over arbitrary topologies and how these secondary motions influence the Reynolds stress distribution in the boundary layer.

Control of supersonic wind-tunnel noise by laminarization of nozzle-wall boundary layer

NASA Technical Reports Server (NTRS)

Beckwith, I. E.; Harvey, W. D.; Harris, J. E.; Holley, B. B.

1973-01-01

One of the principal design requirements for a quiet supersonic or hypersonic wind tunnel is to maintain laminar boundary layers on the nozzle walls and thereby reduce disturbance levels in the test flow. The conditions and apparent reasons for laminar boundary layers which have been observed during previous investigations on the walls of several nozzles for exit Mach numbers from 2 to 20 are reviewed. Based on these results, an analysis and an assessment of nozzle design requirements for laminar boundary layers including low Reynolds numbers, high acceleration, suction slots, wall temperature control, wall roughness, and area suction are presented.

Validation of the k- ω turbulence model for the thermal boundary layer profile of effusive cooled walls

NASA Astrophysics Data System (ADS)

Hink, R.

2015-09-01

The choice of materials for rocket chamber walls is limited by its thermal resistance. The thermal loads can be reduced substantially by the blowing out of gases through a porous surface. The k- ω-based turbulence models for computational fluid dynamic simulations are designed for smooth, non-permeable walls and have to be adjusted to account for the influence of injected fluids. Wilcox proposed therefore an extension for the k- ω turbulence model for the correct prediction of turbulent boundary layer velocity profiles. In this study, this extension is validated against experimental thermal boundary layer data from the Thermosciences Division of the Department of Mechanical Engineering from the Stanford University. All simulations are performed with a finite volume-based in-house code of the German Aerospace Center. Several simulations with different blowing settings were conducted and discussed in comparison to the results of the original model and in comparison to an additional roughness implementation. This study has permitted to understand that velocity profile corrections are necessary in contrast to additional roughness corrections to predict the correct thermal boundary layer profile of effusive cooled walls. Finally, this approach is applied to a two-dimensional simulation of an effusive cooled rocket chamber wall.

Phylogenetic Backgrounds and Virulence-Associated Traits of Escherichia coli Isolates from Surface Waters and Diverse Animals in Minnesota and Wisconsin.

PubMed

Johnson, James R; Johnston, Brian D; Delavari, Parissa; Thuras, Paul; Clabots, Connie; Sadowsky, Michael J

2017-12-15

Possible external reservoirs for extraintestinal pathogenic Escherichia coli (ExPEC) strains that cause infections in humans are poorly defined. Because of the tremendous human health importance of ExPEC infections, we assessed surface waters and domesticated and wild animals in Minnesota and Wisconsin as potential reservoirs of ExPEC of human health relevance. We characterized 595 E. coli isolates (obtained from 1999 to 2002; 280 from seven surface water sites, 315 from feces of 13 wild and domesticated animal species) for phylogroup and virulence genotype, including inferred ExPEC status, by using multiplex PCR-based methods. We also compared the pulsed-field gel electrophoresis (PFGE) profiles of the isolates with a large private PFGE profile library. We found a predominance of non-ExPEC strains (95% and 93% among water and animal isolates, respectively), which were mainly from phylogroups A and B1, plus a minority of ExPEC strains (5% and 7% among water isolates and animal isolates, respectively), predominantly from phylogroup B2. The ExPEC strains, although significantly associated with cats, dogs, and turkeys, occurred in several additional animal species (goat, horse, chicken, pig) and were distributed broadly across all surface water sites. Virulence gene content among the animal source ExPEC isolates segregated significantly in relation to host species, following established patterns. PFGE analysis indicated that 11 study isolates closely matched (94% to 100% profile similarity) reference human clinical and fecal isolates. These findings imply what probably is a low but non-zero risk to humans from environmental and animal source E. coli isolates, especially those from specific human-associated animal species. IMPORTANCE Our detection of potentially pathogenic strains that may pose a health threat to humans among E. coli isolates from surface waters and wild and domesticated animals suggests a need for heightened attention to these reservoirs as possible sources for human acquisition of disease-causing E. coli Although cats, dogs, and turkeys were especially high-prevalence sources, the presence of such strains in other animal species and at all sampled water sites suggests that this potential risk may be widespread. Copyright © 2017 American Society for Microbiology.

Heat transfer in the turbulent boundary layer with a short strip of surface roughness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, R.P.; Chakroun, W.M.

1992-01-01

The effects of a short strip of surface roughness on heat transfer and fluid flow in the turbulent boundary layer are investigated experimentally. This is done by measuring Stanton number and skin friction distributions and mean velocity, turbulence intensity, and mean temperature profiles in a turbulent boundary layer where the first 0.7 m length is smooth, the next 0.2 m is roughened with 1.27 mm hemispheres spaced 2 base diameters apart and the final 1.5 m is smooth. These results are compared with previously published data from experiments wiht a rough leading portion and smooth final portion and from experimentsmore » on an all-smooth surface. The influence of the roughness is large in the neighborhood of the rough strip, but the Stanton number and skin friction distributions are seen to quickly recover smooth-wall behavior downstream of the rough strip. 19 refs.« less

Domain wall roughness and creep in nanoscale crystalline ferroelectric polymers

NASA Astrophysics Data System (ADS)

Xiao, Z.; Poddar, Shashi; Ducharme, Stephen; Hong, X.

2013-09-01

We report piezo-response force microscopy studies of the static and dynamic properties of domain walls (DWs) in 11 to 36 nm thick films of crystalline ferroelectric poly(vinylidene-fluoride-trifluorethylene). The DW roughness exponent ζ ranges from 0.39 to 0.48 and the DW creep exponent μ varies from 0.20 to 0.28, revealing an unexpected effective dimensionality of ˜1.5 that is independent of film thickness. Our results suggest predominantly 2D ferroelectricity in the layered polymer and we attribute the fractal dimensionality to DW deroughening due to the correlations between the in-plane and out-of-plane polarization, an effect that can be exploited to achieve high lateral domain density for developing nanoscale ferroelectrics-based applications.

A Transport Equation Approach to Modeling the Influence of Surface Roughness on Boundary Layer Transition

NASA Astrophysics Data System (ADS)

Langel, Christopher Michael

A computational investigation has been performed to better understand the impact of surface roughness on the flow over a contaminated surface. This thesis highlights the implementation and development of the roughness amplification model in the flow solver OVERFLOW-2. The model, originally proposed by Dassler, Kozulovic, and Fiala, introduces an additional scalar field roughness amplification quantity. This value is explicitly set at rough wall boundaries using surface roughness parameters and local flow quantities. This additional transport equation allows non-local effects of surface roughness to be accounted for downstream of rough sections. This roughness amplification variable is coupled with the Langtry-Menter model and used to modify the criteria for transition. Results from flat plate test cases show good agreement with experimental transition behavior on the flow over varying sand grain roughness heights. Additional validation studies were performed on a NACA 0012 airfoil with leading edge roughness. The computationally predicted boundary layer development demonstrates good agreement with experimental results. New tests using varying roughness configurations are being carried out at the Texas A&M Oran W. Nicks Low Speed Wind Tunnel to provide further calibration of the roughness amplification method. An overview and preliminary results are provided of this concurrent experimental investigation.

Skin friction measurements of systematically-varied roughness: Probing the role of roughness amplitude and skewness

NASA Astrophysics Data System (ADS)

Barros, Julio; Flack, Karen; Schultz, Michael

2017-11-01

Real-world engineering systems which feature either external or internal wall-bounded turbulent flow are routinely affected by surface roughness. This gives rise to performance degradation in the form of increased drag or head loss. However, at present there is no reliable means to predict these performance losses based upon the roughness topography alone. This work takes a systematic approach by generating random surface roughness in which the surface statistics are closely controlled. Skin friction and roughness function results will be presented for two groups of these rough surfaces. The first group is Gaussian (i.e. zero skewness) in which the root-mean-square roughness height (krms) is varied. The second group has a fixed krms, and the skewness is varied from approximately -1 to +1. The effect of the roughness amplitude and skewness on the skin friction will be discussed. Particular attention will be paid to the effect of these parameters on the roughness function in the transitionally-rough flow regime. For example, the role these parameters play in the monotonic or inflectional nature of the roughness function will be addressed. Future research into the details of the turbulence structure over these rough surfaces will also be outlined. Research funded by U.S. Office of Naval Research (ONR).

Photoelectrochemical hydrogen production from biomass derivatives and water.

PubMed

Lu, Xihong; Xie, Shilei; Yang, Hao; Tong, Yexiang; Ji, Hongbing

2014-11-21

Hydrogen, a clean energy carrier with high energy capacity, is a very promising candidate as a primary energy source for the future. Photoelectrochemical (PEC) hydrogen production from renewable biomass derivatives and water is one of the most promising approaches to producing green chemical fuel. Compared to water splitting, hydrogen production from renewable biomass derivatives and water through a PEC process is more efficient from the viewpoint of thermodynamics. Additionally, the carbon dioxide formed can be re-transformed into carbohydrates via photosynthesis in plants. In this review, we focus on the development of photoanodes and systems for PEC hydrogen production from water and renewable biomass derivatives, such as methanol, ethanol, glycerol and sugars. We also discuss the future challenges and opportunities for the design of the state-of-the-art photoanodes and PEC systems for hydrogen production from biomass derivatives and water.

Effects of pressure and temperature on sintering of Cr-doped Al2O3 by pulsed electric current sintering process

NASA Astrophysics Data System (ADS)

Dang, K. Q.; Nanko, M.

2011-03-01

The aluminium oxide crystal, Al2O3, which contains a small amount of chromium, Cr, is called ruby. Pulsed electric current sintering (PECS) was applied to sinter ruby polycrystals. Cr2O3-Al2O3 powder mixture prepared by drying an aqueous slurry containing amounts of Al2O3 and Cr(NO3)3 was consolidated by PECS process. The PECS process was performed in vacuum at sintering temperature raging from 1100 to 1300°C with heating rate of 2 K/min under applied uniaxial pressure varied from 40 to 100 MPa. This study found that highly densified and transparent Cr-doped Al2O3 can be obtained by the PECS process with the high applied pressure at sintering temperature of 1200°C.

Surface Interrogation Scanning Electrochemical Microscopy for a Photoelectrochemical Reaction: Water Oxidation on a Hematite Surface.

PubMed

Kim, Jae Young; Ahn, Hyun S; Bard, Allen J

2018-03-06

To understand the pathway of a photoelectrochemical (PEC) reaction, quantitative knowledge of reaction intermediates is important. We describe here surface interrogation scanning electrochemical microscopy for this purpose (PEC SI-SECM), where a light pulse to a photoactive semiconductor film at a given potential generates intermediates that are then analyzed by a tip generated titrant at known times after the light pulse. The improvements were demonstrated for photoelectrochemical water oxidation (oxygen evolution) reaction on a hematite surface. The density of photoactive sites, proposed to be Fe 4+ species, on a hematite surface was successfully quantified, and the photoelectrochemical water oxidation reaction dynamics were elucidated by time-dependent redox titration experiments. The new configuration of PEC SI-SECM should find expanded usage to understand and investigate more complicated PEC reactions with other materials.

The excited states of a porphine-quinone complex under an external electrostatic field calculated by TDDFT

NASA Astrophysics Data System (ADS)

Aittala, Pekka J.; Cramariuc, Oana; Hukka, Terttu I.

2011-01-01

The potential energy curves (PECs) of the Q, B, and the lowest charge transfer (CT) states of a porphine-2,5-dimethyl-1,4-benzoquinone (PQ) complex have been studied by using the time-dependent density functional theory (TDDFT) with the CAM-B3LYP functional without and with the presence of an external electrostatic field. The PECs calculated using CAM-B3LYP with the original parameters α = 0.19, β = 0.65, and μ = 0.33 a0-1 are practically identical with those obtained using BH&HLYP. Applying of CAM-B3LYP with parameters α = 0.19, β = 0.81, and μ = 0.25 a0-1 yields PECs of the excited states that agree well with the PECs calculated previously using the CC2 method.

All-inorganic perovskite quantum dot/TiO2 inverse opal electrode platform: stable and efficient photoelectrochemical sensing of dopamine under visible irradiation.

PubMed

Chen, Xu; Li, Dongyu; Pan, Gencai; Zhou, Donglei; Xu, Wen; Zhu, Jinyang; Wang, He; Chen, Cong; Song, Hongwei

2018-06-07

CsPbX3 (X = Cl, Br or I) perovskite quantum dots (PQDs) have attracted tremendous attention due to their extraordinarily excellent optical properties. However, there is still an obstacle for their bio-application, which is limited by their water-instability. In this work, we have designed a novel visible light triggered photoelectrochemical (PEC) sensor for dopamine (DA) based on CsPbBr1.5I1.5 PQD immobilized three-dimensional (3D) TiO2 inverse opal photonic crystals (IOPCs). Supported by the TiO2 IOPCs, the water-stability of the PQDs as well as that of the PEC sensor was considerably improved. Furthermore, employed as a photoactive material in PEC sensor, CsPbBr1.5I1.5 PQDs can expand the photocurrent response of the PEC sensor to the whole visible region. In addition, the modulation of the photonic stop band effect of TiO2 IOPCs on the incident light and the emission of PQDs could further enhance the photocurrent response. Such a PEC sensor demonstrates sensitive detection of DA in phosphate buffer saline solution and serum, with a good linear range from 0.1 μM to 250 μM and a low detection limit of approximately 0.012 μM. Our strategy opens an alternative horizon for PQD based PEC sensing, which could be more sensitive, convenient and inexpensive for clinical and biological analysis.

Smooth model surfaces from lignin derivatives. II. Adsorption of polyelectrolytes and PECs monitored by QCM-D.

PubMed

Norgren, Magnus; Gärdlund, Linda; Notley, Shannon M; Htun, Myat; Wågberg, Lars

2007-03-27

For the first time to the knowledge of the authors, well-defined and stable lignin model surfaces have been utilized as substrates in polyelectrolyte adsorption studies. The adsorption of polyallylamine (PAH), poly(acrylic acid) (PAA), and polyelectrolyte complexes (PECs) was monitored using quartz crystal microgravimetry with dissipation (QCM-D). The PECs were prepared by mixing PAH and PAA at different ratios and sequences, creating both cationic and anionic PECs with different charge levels. The adsorption experiments were performed in 1 and 10 mM sodium chloride solutions at pH 5 and 7.5. The highest adsorption of PAH and cationic PECs was found at pH 7.5, where the slightly negatively charged nature of the lignin substrate is more pronounced, governing electrostatic attraction of oppositely charged polymeric substances. An increase in the adsorption was further found when the electrolyte concentration was increased. In comparison, both PAA and the anionic PEC showed remarkably high adsorption to the lignin model film. The adsorption of PAA was further studied on silica and was found to be relatively low even at high electrolyte concentrations. This indicated that the high PAA adsorption on the lignin films was not induced by a decreased solubility of the anionic polyelectrolyte. The high levels of adsorption on lignin model surfaces found both for PAA and the anionic PAA-PAH polyelectrolyte complex points to the presence of strong nonionic interactions in these systems.

Photoelectrochemical devices for solar water splitting - materials and challenges.

PubMed

Jiang, Chaoran; Moniz, Savio J A; Wang, Aiqin; Zhang, Tao; Tang, Junwang

2017-07-31

It is widely accepted within the community that to achieve a sustainable society with an energy mix primarily based on solar energy we need an efficient strategy to convert and store sunlight into chemical fuels. A photoelectrochemical (PEC) device would therefore play a key role in offering the possibility of carbon-neutral solar fuel production through artificial photosynthesis. The past five years have seen a surge in the development of promising semiconductor materials. In addition, low-cost earth-abundant co-catalysts are ubiquitous in their employment in water splitting cells due to the sluggish kinetics of the oxygen evolution reaction (OER). This review commences with a fundamental understanding of semiconductor properties and charge transfer processes in a PEC device. We then describe various configurations of PEC devices, including single light-absorber cells and multi light-absorber devices (PEC, PV-PEC and PV/electrolyser tandem cell). Recent progress on both photoelectrode materials (light absorbers) and electrocatalysts is summarized, and important factors which dominate photoelectrode performance, including light absorption, charge separation and transport, surface chemical reaction rate and the stability of the photoanode, are discussed. Controlling semiconductor properties is the primary concern in developing materials for solar water splitting. Accordingly, strategies to address the challenges for materials development in this area, such as the adoption of smart architectures, innovative device configuration design, co-catalyst loading, and surface protection layer deposition, are outlined throughout the text, to deliver a highly efficient and stable PEC device for water splitting.

Computations of Disturbance Amplification Behind Isolated Roughness Elements and Comparison with Measurements

NASA Technical Reports Server (NTRS)

Choudhari, Meelan; Li, Fei; Bynum, Michael; Kegerise, Michael; King, Rudolph

2015-01-01

Computations are performed to study laminar-turbulent transition due to isolated roughness elements in boundary layers at Mach 3.5 and 5.95, with an emphasis on flow configurations for which experimental measurements from low disturbance wind tunnels are available. The Mach 3.5 case corresponds to a roughness element with right-triangle planform with hypotenuse that is inclined at 45 degrees with respect to the oncoming stream, presenting an obstacle with spanwise asymmetry. The Mach 5.95 case corresponds to a circular roughness element along the nozzle wall of the Purdue BAMQT wind tunnel facility. In both cases, the mean flow distortion due to the roughness element is characterized by long-lived streamwise streaks in the roughness wake, which can support instability modes that did not exist in the absence of the roughness element. The linear amplification characteristics of the wake flow are examined towards the eventual goal of developing linear growth correlations for the onset of transition.

Comparative Genomics of Escherichia coli Isolated from Skin and Soft Tissue and Other Extraintestinal Infections.

PubMed

Ranjan, Amit; Shaik, Sabiha; Nandanwar, Nishant; Hussain, Arif; Tiwari, Sumeet K; Semmler, Torsten; Jadhav, Savita; Wieler, Lothar H; Alam, Munirul; Colwell, Rita R; Ahmed, Niyaz

2017-08-15

Escherichia coli , an intestinal Gram-negative bacterium, has been shown to be associated with a variety of diseases in addition to intestinal infections, such as urinary tract infections (UTIs), meningitis in neonates, septicemia, skin and soft tissue infections (SSTIs), and colisepticemia. Thus, for nonintestinal infections, it is categorized as extraintestinal pathogenic E. coli (ExPEC). It is also an opportunistic pathogen, causing cross infections, notably as an agent of zoonotic diseases. However, comparative genomic data providing functional and genetic coordinates for ExPEC strains associated with these different types of infections have not proven conclusive. In the study reported here, ExPEC E. coli isolated from SSTIs was characterized, including virulence and drug resistance profiles, and compared with isolates from patients suffering either pyelonephritis or septicemia. Results revealed that the majority of the isolates belonged to two pathogenic phylogroups, B2 and D. Approximately 67% of the isolates were multidrug resistant (MDR), with 85% producing extended-spectrum beta-lactamase (ESBL) and 6% producing metallo-beta-lactamase (MBL). The bla CTX-M-15 genotype was observed in at least 70% of the E. coli isolates in each category, conferring resistance to an extended range of beta-lactam antibiotics. Whole-genome sequencing and comparative genomics of the ExPEC isolates revealed that two of the four isolates from SSTIs, NA633 and NA643, belong to pandemic sequence type ST131, whereas functional characteristics of three of the ExPEC pathotypes revealed that they had equal capabilities to form biofilm and were resistant to human serum. Overall, the isolates from a variety of ExPEC infections demonstrated similar resistomes and virulomes and did not display any disease-specific functional or genetic coordinates. IMPORTANCE Infections caused by extraintestinal pathogenic E. coli (ExPEC) are of global concern as they result in significant costs to health care facilities management. The recent emergence of a multidrug-resistant pandemic clone, Escherichia coli ST131, is of primary concern as a global threat. In developing countries, such as India, skin and soft tissue infections (SSTIs) associated with E. coli are marginally addressed. In this study, we employed both genomic analysis and phenotypic assays to determine relationships, if any, among the ExPEC pathotypes. Similarity between antibiotic resistance and virulence profiles was observed, ST131 isolates from SSTIs were reported, and genomic similarities among strains isolated from different disease conditions were detected. This study provides functional molecular infection epidemiology insight into SSTI-associated E. coli compared with ExPEC pathotypes. Copyright © 2017 Ranjan et al.

CDC42 is required for epicardial and pro-epicardial development by mediating FGF receptor trafficking to the plasma membrane

PubMed Central

Li, Jingjing; Miao, Lianjie; Zhao, Chen; Shaikh Qureshi, Wasay Mohiuddin; Shieh, David; Guo, Hua; Lu, Yangyang; Hu, Saiyang; Huang, Alice; Zhang, Lu; Cai, Chen-leng; Wan, Leo Q.; Xin, Hongbo; Vincent, Peter; Singer, Harold A.; Zheng, Yi; Cleaver, Ondine; Fan, Zhen-Chuan

2017-01-01

The epicardium contributes to multiple cardiac lineages and is essential for cardiac development and regeneration. However, the mechanism of epicardium formation is unclear. This study aimed to establish the cellular and molecular mechanisms underlying the dissociation of pro-epicardial cells (PECs) from the pro-epicardium (PE) and their subsequent translocation to the heart to form the epicardium. We used lineage tracing, conditional deletion, mosaic analysis and ligand stimulation in mice to determine that both villous protrusions and floating cysts contribute to PEC translocation to myocardium in a CDC42-dependent manner. We resolved a controversy by demonstrating that physical contact of the PE with the myocardium constitutes a third mechanism for PEC translocation to myocardium, and observed a fourth mechanism in which PECs migrate along the surface of the inflow tract to reach the ventricles. Epicardial-specific Cdc42 deletion disrupted epicardium formation, and Cdc42 null PECs proliferated less, lost polarity and failed to form villous protrusions and floating cysts. FGF signaling promotes epicardium formation in vivo, and biochemical studies demonstrated that CDC42 is involved in the trafficking of FGF receptors to the cell membrane to regulate epicardium formation. PMID:28465335

Fracture mode, microstructure and temperature-dependent elastic moduli for thermoelectric composites of PbTe-PbS with SiC nanoparticle additions

NASA Astrophysics Data System (ADS)

Ni, Jennifer E.; Case, Eldon D.; Schmidt, Robert D.; Wu, Chun-I.; Hogan, Timothy P.; Trejo, Rosa M.; Lara-Curzio, Edgar; Kanatzidis, Mercouri G.

2013-12-01

Twenty-six (Pb0.95Sn0.05Te)0.92(PbS)0.08-0.055% PbI2-SiC nanoparticle (SiCnp) composite thermoelectric specimens were either hot pressed or pulsed electric current sintered (PECS). Bloating (a thermally induced increase in porosity, P, for as-densified specimens) was observed during annealing at temperatures >603 K for hot-pressed specimens and PECS-processed specimens from wet milled powders, but in contrast seven out of seven specimens densified by PECS from dry milled powders showed no observable bloating following annealing at temperatures up to 936 K. In this study, bloating in the specimens was accessed via thermal annealing induced changes in (i) porosity measured by scanning electron microscopy on fractured specimen surfaces, (ii) specimen volume and (iii) elastic moduli. The moduli were measured by resonant ultrasound spectroscopy. SiCnp additions (1-3.5 vol.%) changed the fracture mode from intergranular to transgranular, inhibited grain growth, and limited bloating in the wet milled PECS specimens. Inhibition of bloating likely occurs due to cleaning of contamination from powder particle surfaces via PECS processing which has been reported previously in the literature.

Simplified human model and pedestrian simulation in the millimeter-wave region

NASA Astrophysics Data System (ADS)

Han, Junghwan; Kim, Seok; Lee, Tae-Yun; Ka, Min-Ho

2016-02-01

The 24 GHz and 77 GHz radar sensors have been studied as a strong candidate for advanced driver assistance systems(ADAS) because of their all-weather capability and accurate range and radial velocity measuring scheme. However, developing a reliable pedestrian recognition system hasmany obstacles due to the inaccurate and non-trivial radar responses at these high frequencies and the many combinations of clothes and accessories. To overcome these obstacles, many researchers used electromagnetic (EM) simulation to characterize the radar scattering response of a human. However, human simulation takes so long time because of the electrically huge size of a human in the millimeter-wave region. To reduce simulation time, some researchers assumed the skin of a human is the perfect electric conductor (PEC) and have simulated the PEC human model using physical optics (PO) algorithm without a specific explanation about how the human body could be modeled with PEC. In this study, the validity of the assumption that the surface of the human body is considered PEC in the EM simulation is verified, and the simulation result of the dry skin human model is compared with that of the PEC human model.

Partitionable-space enhanced coagulation (PEC) reactor and its working mechanism: a new prospective chemical technology for phosphorus pollution control.

PubMed

Zhang, Meng; Zheng, Ping; Abbas, Ghulam; Chen, Xiaoguang

2014-02-01

Phosphorus pollution control and phosphorus recycling, simultaneously, are focus of attention in the wastewater treatment. In this work, a novel reactor named partitionable-space enhanced coagulation (PEC) was invented for phosphorus control. The working performance and process mechanism of PEC reactor were investigated. The results showed that the PEC technology was highly efficient and cost-effective. The volumetric removal rate (VRR) reached up to 2.86 ± 0.04 kg P/(m(3) d) with a phosphorus removal rate of over 97%. The precipitant consumption was reduced to 2.60-2.76 kg Fe(II)/kg P with low operational cost of $ 0.632-0.673/kg P. The peak phosphorus content in precipitate was up to 30.44% by P2O5, which reveal the benefit of the recycling phosphorus resource. The excellent performance of PEC technology was mainly attributed to the partitionable-space and 'flocculation filter'. The partition limited the trans-regional back-mixing of reagents along the reactor, which promoted the precipitation reaction. The 'flocculation filter' retained the microflocs, enhancing the flocculation process. Copyright © 2013 Elsevier Ltd. All rights reserved.

Surface- and interface-engineered heterostructures for solar hydrogen generation

NASA Astrophysics Data System (ADS)

Chen, Xiangyan; Li, Yanrui; Shen, Shaohua

2018-04-01

Photoelectrochemical (PEC) water splitting based on semiconductor photoelectrodes provides a promising platform for reducing environmental pollution and solving the energy crisis by developing clean, sustainable and environmentally friendly hydrogen energy. In this context, metal oxides with their advantages including low cost, good chemical stability and environmental friendliness, have attracted extensive attention among the investigated candidates. However, the large bandgap, poor charge transfer ability and high charge recombination rate limit the PEC performance of metal oxides as photoelectrodes. To solve this limitation, many approaches toward enhanced PEC water splitting performance, which focus on surface and interface engineering, have been presented. In this topical review, we concentrate on the heterostructure design of some typical metal oxides with narrow bandgaps (e.g. Fe2O3, WO3, BiVO4 and Cu2O) as photoelectrodes. An overview of the surface- and interface-engineered heterostructures, including semiconductor heterojunctions, surface protection, surface passivation and cocatalyst decoration, will be given to introduce the recent advances in metal oxide heterostructures for PEC water splitting. This article aims to provide fundamental references and principles for designing metal oxide heterostructures with high activity and stability as photoelectrodes for PEC solar hydrogen generation.

Graphene-doped Bi2S3 nanorods as visible-light photoelectrochemical aptasensing platform for sulfadimethoxine detection.

PubMed

Okoth, Otieno Kevin; Yan, Kai; Liu, Yong; Zhang, Jingdong

2016-12-15

Bismuth sulphide (Bi2S3) nanorods doped with graphene (G) were synthesized and explored as photoactive materials for constructing a photoelectrochemical (PEC) aptasensor for sulfadimethoxine (SDM) detection. The formation of Bi2S3 nanorods and G nanosheets was observed by scanning electron microscopy (SEM) and further characterized by X-ray diffraction (XRD) spectroscopy. The PEC measurements indicated that the photocurrent response of Bi2S3 was obviously improved by doping suitable amount of G. The G-Bi2S3 composite coated electrode was utilized for fabricating a PEC aptasensor by covalently immobilizing a 5'-amino-terminated SDM aptamer on the electrode surface. Based on the specific interaction between SDM and the aptamer, a PEC sensor responsive to SDM was obtained. Under optimal conditions, the proposed sensor showed a linear photocurrent response to SDM in the concentration range of 1.0-100nM, with a low detection limit (3S/N) of 0.55nM. Moreover, the sensor showed high sensitivity, stability and reproducibility. The potential applicability of the PEC aptasensor was confirmed by detecting SDM in veterinary drug formulation and milk. Copyright © 2016 Elsevier B.V. All rights reserved.

Aging near the wall in colloidal glasses

NASA Astrophysics Data System (ADS)

Cao, Cong; Huang, Xinru; Weeks, Eric

In a colloidal glass system, particles move slower as sample ages. In addition, their motions may be affected by their local structure, and this structure will be different near a wall. We examine how the aging process near a wall differs from that in the bulk of the sample. In particular, we use a confocal microscope to observe 3D motion in a bidisperse colloidal glass sample. We find that flat walls induce the particles to organize into layers. The aging process behaves differently near the boundary, especially within the first three layers. Particle motion near the wall is noticeably slower but also changes less dramatically with age. We compare and contrast aging seen in samples with flat and rough walls.

Curb Mounting, Vertical Mobility, and Inverted Mobility on Rough Surfaces Using Microspine-Enabled Robots

NASA Technical Reports Server (NTRS)

Parness, Aaron

2012-01-01

Three robots that extend microspine technology to enable advanced mobility are presented. First, the Durable Reconnaissance and Observation Platform (DROP) and the ReconRobotics Scout platform use a new rotary configuration of microspines to provide improved soldier-portable reconnaissance by moving rapidly over curbs and obstacles, transitioning from horizontal to vertical surfaces, climbing rough walls and surviving impacts. Next, the four-legged LEMUR robot uses new configurations of opposed microspines to anchor to both manmade and natural rough surfaces. Using these anchors as feet enables mobility in unstructured environments, from urban disaster areas to deserts and caves.

Experimental and numerical investigation of the effect of distributed suction on oblique shock wave/turbulent boundary layer interaction. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Benhachmi, Driss; Greber, Isaac; Hingst, Warren R.

1988-01-01

A combined experimental and numerical study of the interaction of an incident oblique shock wave with a turbulent boundary layer on a rough plate and on a porous plate with suction is presented. The experimental phase involved the acquisition of mean data upstream of, within, and downstream of the interaction region at Mach numbers 2.5 and 3.0. Data were taken at unit Reynolds numbers of 1.66 E7 and 1.85 E7 m respectively, and for flow deflection angles of 0, 4, 6 and 8 degs. Measured data include wall static pressure, pitot pressure profiles, and local bleed distributions on the porous plate. On the rough plate, with no suction, the boundary layer profiles were modified near the wall, but not separated for the 4 deg flow deflection angle. For the higher deflection angles of 6 and 8 degs, the boundary layer was separated. Suction increases the strength of the incident shock required to separate the turbulent boundary layer; for all shock strengths tested, separation is completely eliminated. The pitot pressure profiles are affected throughout the whole boundary layer; they are fuller than the ones obtained on the rough plate. It is also found that the combination of suction and roughness introduces spatial perturbations.

The flow field around a pair of cubic roughness elements with different spacings immersed in turbulent boundary layer

NASA Astrophysics Data System (ADS)

Agarwal, Karuna; Gao, Jian; Katz, Joseph

2017-11-01

The shape, size, and spacing between roughness elements in turbulent boundary layers affect the associated drag and noise. Understanding them require data on the flow structure around these elements. Dual-view tomographic holography is used to study the 3D 3-component velocity field around a pair of cubic roughness elements immersed in a turbulent boundary layer at Reτ = 2500 . These a = 1 mm high cubes correspond to 4% of the half channel height and 90 wall units (δν = 11 μ m). Tests are performed for spanwise spacings of a, 1.5 a and 2.5 a. The sample volume is 385δν × 250δν × 190δν and the vector spacing is 5.4δν. Conversed statistics is obtained by recording 1500 realizations in volumes centered upstream, downstream and around a cube. The boundary layer separating upstream of the cube does not reattach until the wake region, resulting in formation of a vortical ``canopy'' that engulfs each cube. It is dominated by spanwise vorticity above the cube and separated region, bounded by vertical vorticity on the sides. Flow channeling in the space between cubes causes asymmetry in the vorticity distributions along the inner and outer walls. The legs of horseshoe vortices remain near the wall between cubes, but grow and expand in the wake region. Funded by NSF and ONR.

Risk factors for post-colorectal endoscopic submucosal dissection (ESD) coagulation syndrome: a multicenter, prospective, observational study

PubMed Central

Arimoto, Jun; Higurashi, Takuma; Kato, Shingo; Fuyuki, Akiko; Ohkubo, Hidenori; Nonaka, Takashi; Yamaguchi, Yoshikazu; Ashikari, Keiichi; Chiba, Hideyuki; Goto, Shungo; Taguri, Masataka; Sakaguchi, Takashi; Atsukawa, Kazuhiro; Nakajima, Atsushi

2018-01-01

Background and study aims  Colorectal cancer (CRC) is one of the most common neoplasms and endoscopic submucosal dissection (ESD) is an effective treatment for early-stage CRC. However, it has been observed that patients undergoing ESD often complain of pain, even if ESD has been successfully performed. Risk factors for such pain still remain unknown. The aim of this study was to explore the risk factors for post-colorectal ESD coagulation syndrome (PECS). Patients and methods  This was a prospective multicenter observational trial (UMIN000016781) conducted in 106 of 223 patients who underwent ESD between March 2015 and April 2016. We investigated age, sex, tumor location, ESD operation time, lesion size, duration of hospitalization, and frequency of PECS. We defined PECS as local abdominal pain (evaluated on a visual analogue scale) in the region corresponding to the site of the ESD that occurred within 4 days of the procedure. Results  PECS occurred in 15/106 (14.2 %), and 10 were women ( P  = 0.01, OR: 7.74 [1.6 – 36.4]), 7 had lesions in the cecum ( P  < 0.001, OR: 20.6 [3.7 – 115.2]), and 9 in whom ESD operation time was > 90 min ( P  = 0.002, OR: 10.3 [2.4 – 44.6]). Frequency of deviation from the prescribed clinical path was significantly higher (47 % [7/15] vs. 2 % [2/91], P  < 0.001, OR: 38.9 [6.9 – 219.6]), and hospital stay was significantly longer in the PECS group.  Conclusions  Female gender, location of lesion in the cecum, and ESD operation time > 90 minutes were significant risk factors independent of PECS. These findings are important to management of PECS.  PMID:29527556

Prospective double blind randomized placebo-controlled clinical trial of the pectoral nerves (Pecs) block type II.

PubMed

Versyck, Barbara; van Geffen, Geert-Jan; Van Houwe, Patrick

2017-08-01

The aim of this clinical trial was to test the hypothesis whether adding the pectoral nerves (Pecs) block type II to the anesthetic procedure reduces opioid consumption during and after breast surgery. A prospective randomized double blind placebo-controlled study. A secondary hospital. 140 breast cancer stage 1-3 patients undergoing mastectomy or tumorectomy with sentinel node or axillary node dissection. Patients were randomized to receive either a Pecs block with levobupivacaine 0.25% (n=70) or placebo block with saline (n=70). The pain levels were evaluated by Numeric Rating Scale (NRS) pain scores at 15-minute intervals during the post anesthesia care unit stay time (PACU), at 2-hour intervals for the first 24h on the ward and at 4-hour intervals for the next 24h. Intraoperative and postoperative opioid consumption were recorded during the full stay. Patient satisfaction was evaluated upon discharge using a 10-point scale. Intraoperative sufentanil requirements were comparable for the Pecs and placebo group (8.0±3.5μg and 7.8±3.0μg, P=0.730). Patients in the Pecs group experienced significantly less pain than patients in the control group (P=0.048) during their PACU stay. Furthermore, patients in the Pecs group required significant less postoperative opioids (9.16±10.15mg and 14.97±14.38mg morphine equivalent, P=0.037) and required significant fewer postsurgical opioid administration interventions than patients in the control group (P=0.045). Both patient-groups were very satisfied about their management (9.6±0.6 and 9.1±1.8 on a 10-point scale, P=0.211). The Pecs block reduces postsurgical opioid consumption during the PACU stay time for patients undergoing breast surgery. Copyright © 2017 Elsevier Inc. All rights reserved.

Directing the phase behavior of polyelectrolyte complexes using chiral patterned peptides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pacalin, Naomi M.; Leon, Lorraine; Tirrell, Matthew

Polyelectrolyte complexes (PECs) have a broad range of promising applications as soft materials due to their self-assembly and diversity of structure and chemical composition. Peptide polymer PECs are highly biocompatible and biodegradable, making them particularly useful for encapsulation of food additives and flavors, micellar drug delivery, medical and underwater adhesives, fetal membrane patches, and scaffolds for cell growth in tissue engineering. While parameters affecting PEC formation and stability in regards to charge effects are well researched, little is known about the effects of van der Waals interactions, hydrogen bonding, and secondary structure in these materials. Peptide chirality provides a uniquemore » opportunity to manipulate PEC phase to modulate the amount of solid-like (precipitate) or liquid-like (coacervate) character by influencing hydrogen bonding interactions among peptide chains. In previous work, we showed that chiral peptides form solid complexes, while complexes with even one racemic peptide were fluid. This raised the interesting question of how long a homochiral sequence must be to result in solid phase formation. In this work, we designed chiral patterned peptides of polyglutamic acid and polylysine ranging from 50 to 90% L-chiral residues with increasing numbers of sequential L-chiral residues before a chirality change. These polymers were mixed together to form PECs. We observed that 8 or more sequential L-chiral residues are necessary to achieve both the appearance of a precipitate phase and sustained beta-sheets in the complex, as determined by optical imaging and FTIR Spectroscopy. Less homochiral content results in formation of a coacervate phase. Thus, we show that chiral sequence can be used to control the phase transition of PECs. Understanding how to manipulate PEC phase using chiral sequence as presented here may enable tuning of the material properties to achieve the desired mechanical strength for coatings and polymer brushes, or the most effective molecular release kinetics for drug delivery applications, for example.« less

Frequency of hepatitis E virus, rotavirus and porcine enteric calicivirus at various stages of pork carcass processing in two pork processing plants.

PubMed

Jones, Tineke H; Muehlhauser, Victoria

2017-10-16

Hepatitis E virus (HEV), rotavirus (RV), and porcine enteric calicivirus (PEC) infections are common in swine and raises concerns about the potential for zoonotic transmission through undercooked meat products. Enteric viruses can potentially contaminate carcasses during meat processing operations. There is a lack of information on the prevalence and control of enteric viruses in the pork processing chain. This study compared the incidence and levels of contamination of hog carcasses with HEV, RV and PEC at different stages of the dressing process. A total of 1000 swabs were collected from 2 pork processing plants on 10 separate occasions over the span of a year. The samples were obtained from random sites on hog carcasses at 4 dressing stages (plant A: bleeding, dehairing, pasteurization, and evisceration; plant B: bleeding, skinning, evisceration, and washing) and from meat cuts. Numbers of genome copies (gc) of HEV, RV and PEC were determined by RT-qPCR. RV and PEC were detected in 100%, and 18% of samples, respectively, after bleeding for plant A and in 98%, and 36% of samples, respectively, after bleeding for plant B. After evisceration, RV and PEC were detected in 21% and 3% of samples, respectively, for plant A and in 1%, and 0% of samples, respectively for plant B. RV and PEC were detected on 1%, and 5% of pork cuts, respectively, for plant A and on 0%, and 0% of pork cuts, respectively, for plant B. HEV was not detected in any pork carcass or retail pork samples from plants A or B. The frequency of PEC and RV on pork is progressively reduced along the pork processing chain but the viruses were not completely eliminated. The findings suggest that consumers could be at risk when consuming undercooked meat contaminated with pathogenic enteric viruses. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

Combining Quantitative Genetic Footprinting and Trait Enrichment Analysis to Identify Fitness Determinants of a Bacterial Pathogen

PubMed Central

Wiles, Travis J.; Norton, J. Paul; Russell, Colin W.; Dalley, Brian K.; Fischer, Kael F.; Mulvey, Matthew A.

2013-01-01

Strains of Extraintestinal Pathogenic Escherichia c oli (ExPEC) exhibit an array of virulence strategies and are a major cause of urinary tract infections, sepsis and meningitis. Efforts to understand ExPEC pathogenesis are challenged by the high degree of genetic and phenotypic variation that exists among isolates. Determining which virulence traits are widespread and which are strain-specific will greatly benefit the design of more effective therapies. Towards this goal, we utilized a quantitative genetic footprinting technique known as transposon insertion sequencing (Tn-seq) in conjunction with comparative pathogenomics to functionally dissect the genetic repertoire of a reference ExPEC isolate. Using Tn-seq and high-throughput zebrafish infection models, we tracked changes in the abundance of ExPEC variants within saturated transposon mutant libraries following selection within distinct host niches. Nine hundred and seventy bacterial genes (18% of the genome) were found to promote pathogen fitness in either a niche-dependent or independent manner. To identify genes with the highest therapeutic and diagnostic potential, a novel Trait Enrichment Analysis (TEA) algorithm was developed to ascertain the phylogenetic distribution of candidate genes. TEA revealed that a significant portion of the 970 genes identified by Tn-seq have homologues more often contained within the genomes of ExPEC and other known pathogens, which, as suggested by the first axiom of molecular Koch's postulates, is considered to be a key feature of true virulence determinants. Three of these Tn-seq-derived pathogen-associated genes—a transcriptional repressor, a putative metalloendopeptidase toxin and a hypothetical DNA binding protein—were deleted and shown to independently affect ExPEC fitness in zebrafish and mouse models of infection. Together, the approaches and observations reported herein provide a resource for future pathogenomics-based research and highlight the diversity of factors required by a single ExPEC isolate to survive within varying host environments. PMID:23990803

Photoelectrocatalytic degradation of methylene blue using F doped TiO2 photoelectrode under visible light irradiation.

PubMed

Liu, Dong; Tian, Renwen; Wang, Jianqiao; Nie, Er; Piao, Xianqing; Li, Xin; Sun, Zhuo

2017-10-01

Photoelectrocatalysis (PEC) has attracted great interest due to cost effectiveness and high efficiency in water treatment. In this study, F doped TiO 2 (F-TiO 2 ) photoelectrodes with honeycomb like morphology were prepared, and the PEC performance was investigated. F-TiO 2 particles that showed enhanced absorption of visible light were synthesized via a sol-gel method. F-TiO 2 particles were anchored onto the surface of F-doped SnO 2 glass by a screen-printing method to prepare the F-TiO 2 photoelectrodes. The PEC performance of the F-TiO 2 photoelectrodes was investigated via the degradation of methylene blue (MB) under visible light irradiation. The results show that the F-TiO 2 photoelectrodes exhibited an excellent PEC performance that was affected by the F doping content, applied bias and solution pH. A maximum decolorization percentage of 97.8% was achieved by the FT-15 photoelectrode, with a 1.4 V bias at pH 9.94 after 4.0 h of visible light irradiation. The high PEC performance of the F-TiO 2 photoelectrodes is mainly ascribed to the efficient separation of electron-hole (e - -h + ) pairs and the creation of active radicals such as hydroxyl radicals (OH). The PEC decolorization kinetic data were analyzed using the first-order kinetic model and the Langmuir-Hinshelwood (L-H) model. The data indicates that the PEC degradation of MB molecules mainly occurred on the surface of the F-TiO 2 photoelectrodes, and the MB molecules were discolored mainly by h + (41.5%) and OH (46.5%). In addition, 8.2% of the MB molecules were discolored by other oxidative species, and 3.8% of the MB molecules were discolored by self-sensitized oxidation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Heme oxygenase-1-mediated autophagy protects against pulmonary endothelial cell death and development of emphysema in cadmium-treated mice

PubMed Central

Surolia, Ranu; Karki, Suman; Kim, Hyunki; Yu, Zhihong; Kulkarni, Tejaswini; Mirov, Sergey B.; Carter, A. Brent; Rowe, Steven M.; Matalon, Sadis; Thannickal, Victor J.; Agarwal, Anupam

2015-01-01

Pulmonary exposure to cadmium, a major component of cigarette smoke, has a dramatic impact on lung function and the development of emphysema. Cigarette smoke exposure induces heme oxygenase-1 (HO-1), a cytoprotective enzyme. In this study, we employed a truncated mouse model of emphysema by intratracheal instillation of cadmium (CdCl2) solution (0.025% per 1 mg/kg body wt) in HO-1+/+, HO-1−/−, and overexpressing humanized HO-1 bacterial artificial chromosome (hHO-1BAC) mice. We evaluated the role of HO-1 in cadmium-induced emphysema in mice by analyzing histopathology, micro-computed tomography scans, and lung function tests. CdCl2-exposed HO-1−/− mice exhibited more severe emphysema compared with HO-1+/+ or hHO-1BAC mice. Loss of pulmonary endothelial cells (PECs) from the alveolar capillary membrane is recognized to be a target in emphysema. PECs from HO-1+/+, HO-1−/−, and hHO-1BAC were employed to define the underlying molecular mechanism for the protection from emphysema by HO-1. Electron microscopy, expression of autophagic markers (microtubule-associated protein 1B-light chain 3 II, autophagy protein 5, and Beclin1) and apoptotic marker (cleaved caspase 3) suggested induction of autophagy and apoptosis in PECs after CdCl2 treatment. CdCl2-treated HO-1−/− PECs exhibited downregulation of autophagic markers and significantly increased cleaved caspase 3 expression and activity (∼4-fold higher). Moreover, hHO-1BAC PECs demonstrated upregulated autophagy and absence of cleaved caspase 3 expression or activity. Pretreatment of HO-1+/+ PECs with rapamycin induced autophagy and resulted in reduced cell death upon cadmium treatment. Induction of autophagy following CdCl2 treatment was found to be protective from apoptotic cell death. HO-1 induced protective autophagy in PECs and mitigated cadmium-induced emphysema. PMID:26071551

Heme oxygenase-1-mediated autophagy protects against pulmonary endothelial cell death and development of emphysema in cadmium-treated mice.

PubMed

Surolia, Ranu; Karki, Suman; Kim, Hyunki; Yu, Zhihong; Kulkarni, Tejaswini; Mirov, Sergey B; Carter, A Brent; Rowe, Steven M; Matalon, Sadis; Thannickal, Victor J; Agarwal, Anupam; Antony, Veena B

2015-08-01

Pulmonary exposure to cadmium, a major component of cigarette smoke, has a dramatic impact on lung function and the development of emphysema. Cigarette smoke exposure induces heme oxygenase-1 (HO-1), a cytoprotective enzyme. In this study, we employed a truncated mouse model of emphysema by intratracheal instillation of cadmium (CdCl2) solution (0.025% per 1 mg/kg body wt) in HO-1(+/+), HO-1(-/-), and overexpressing humanized HO-1 bacterial artificial chromosome (hHO-1BAC) mice. We evaluated the role of HO-1 in cadmium-induced emphysema in mice by analyzing histopathology, micro-computed tomography scans, and lung function tests. CdCl2-exposed HO-1(-/-) mice exhibited more severe emphysema compared with HO-1(+/+) or hHO-1BAC mice. Loss of pulmonary endothelial cells (PECs) from the alveolar capillary membrane is recognized to be a target in emphysema. PECs from HO-1(+/+), HO-1(-/-), and hHO-1BAC were employed to define the underlying molecular mechanism for the protection from emphysema by HO-1. Electron microscopy, expression of autophagic markers (microtubule-associated protein 1B-light chain 3 II, autophagy protein 5, and Beclin1) and apoptotic marker (cleaved caspase 3) suggested induction of autophagy and apoptosis in PECs after CdCl2 treatment. CdCl2-treated HO-1(-/-) PECs exhibited downregulation of autophagic markers and significantly increased cleaved caspase 3 expression and activity (∼4-fold higher). Moreover, hHO-1BAC PECs demonstrated upregulated autophagy and absence of cleaved caspase 3 expression or activity. Pretreatment of HO-1(+/+) PECs with rapamycin induced autophagy and resulted in reduced cell death upon cadmium treatment. Induction of autophagy following CdCl2 treatment was found to be protective from apoptotic cell death. HO-1 induced protective autophagy in PECs and mitigated cadmium-induced emphysema. Copyright © 2015 the American Physiological Society.

Modeling the Inactivation of Intestinal Pathogenic Escherichia coli O157:H7 and Uropathogenic E. coli in Ground Chicken by High Pressure Processing and Thymol

PubMed Central

Chien, Shih-Yung; Sheen, Shiowshuh; Sommers, Christopher H.; Sheen, Lee-Yan

2016-01-01

Disease causing Escherichia coli commonly found in meat and poultry include intestinal pathogenic E. coli (iPEC) as well as extraintestinal types such as the Uropathogenic E. coli (UPEC). In this study we compared the resistance of iPEC (O157:H7) to UPEC in chicken meat using High Pressure Processing (HPP) in with (the hurdle concept) and without thymol essential oil as a sensitizer. UPEC was found slightly more resistant than E. coli O157:H7 (iPEC O157:H7) at 450 and 500 MPa. A central composite experimental design was used to evaluate the effect of pressure (300–400 MPa), thymol concentration (100–200 ppm), and pressure-holding time (10–20 min) on the inactivation of iPEC O157:H7 and UPEC in ground chicken. The hurdle approach reduced the high pressure levels and thymol doses imposed on the food matrices and potentially decreased food quality damaged after treatment. The quadratic equations were developed to predict the impact (lethality) on iPEC O157:H7 (R2 = 0.94) and UPEC (R2 = 0.98), as well as dimensionless non-linear models [Pr > F (<0.0001)]. Both linear and non-linear models were validated with data obtained from separated experiment points. All models may predict the inactivation/lethality within the same order of accuracy. However, the dimensionless non-linear models showed potential applications with parameters outside the central composite design ranges. The results provide useful information of both iPEC O157:H7 and UPEC in regard to how they may survive HPP in the presence or absence of thymol. The models may further assist regulatory agencies and food industry to assess the potential risk of iPEC O157:H7 and UPEC in ground chicken. PMID:27379050

Directing the phase behavior of polyelectrolyte complexes using chiral patterned peptides

NASA Astrophysics Data System (ADS)

Pacalin, Naomi M.; Leon, Lorraine; Tirrell, Matthew

2016-10-01

Polyelectrolyte complexes (PECs) have a broad range of promising applications as soft materials due to their self-assembly and diversity of structure and chemical composition. Peptide polymer PECs are highly biocompatible and biodegradable, making them particularly useful for encapsulation of food additives and flavors, micellar drug delivery, medical and underwater adhesives, fetal membrane patches, and scaffolds for cell growth in tissue engineering. While parameters affecting PEC formation and stability in regards to charge effects are well researched, little is known about the effects of van der Waals interactions, hydrogen bonding, and secondary structure in these materials. Peptide chirality provides a unique opportunity to manipulate PEC phase to modulate the amount of solid-like (precipitate) or liquid-like (coacervate) character by influencing hydrogen bonding interactions among peptide chains. In previous work, we showed that chiral peptides form solid complexes, while complexes with even one racemic peptide were fluid. This raised the interesting question of how long a homochiral sequence must be to result in solid phase formation. In this work, we designed chiral patterned peptides of polyglutamic acid and polylysine ranging from 50 to 90% L-chiral residues with increasing numbers of sequential L-chiral residues before a chirality change. These polymers were mixed together to form PECs. We observed that 8 or more sequential L-chiral residues are necessary to achieve both the appearance of a precipitate phase and sustained β-sheets in the complex, as determined by optical imaging and FTIR Spectroscopy. Less homochiral content results in formation of a coacervate phase. Thus, we show that chiral sequence can be used to control the phase transition of PECs. Understanding how to manipulate PEC phase using chiral sequence as presented here may enable tuning of the material properties to achieve the desired mechanical strength for coatings and polymer brushes, or the most effective molecular release kinetics for drug delivery applications, for example.

Ni-doped TiO2 nanotubes photoanode for enhanced photoelectrochemical water splitting

NASA Astrophysics Data System (ADS)

Dong, Zhenbiao; Ding, Dongyan; Li, Ting; Ning, Congqin

2018-06-01

Photoelectrochemical (PEC) water splitting hydrogen production provides a promising way for sustainable development. In this work, we prepared Ni-doped TiO2 (Ti-Ni-O) nanotubes through anodizing different Ti-Ni alloys and further annealing them at elevated temperatures, and reported their PEC water splitting performance. It was found that Ni doping could improve light absorption and facilitate separation of photo-excited electron-hole pair. The nanotubes fabricated on Ti-1 wt.% Ni alloy and annealed at 550 °C exhibited better PEC water splitting performance than those on Ti-10 wt.% Ni alloy. The photoconversion efficiency was 0.67%, which was 3.35 times the photoconversion efficiency of undoped TiO2. It demonstrated that it was feasible to fabricate high-performance Ti-Ni-O nanotubes on Ti-Ni alloys and used as photoanode for improving PEC water splitting.

A Comparison of PECS and iPad to Teach Requesting to Pre-schoolers with Autistic Spectrum Disorders.

PubMed

Agius, May M; Vance, Margaret

2016-01-01

Few studies have compared the efficacy of the Picture Exchange Communication System (PECS) and iPads used as speech generating devices (SGDs), and none have targeted preschoolers. This study compares the relative efficacy of PECS and an iPad/SGD with three preschool-aged children with autism spectrum disorder and limited functional speech who lived in Malta. The study utilized an adapted alternating treatment design embedded in a multiple baseline design, with requesting of reinforcers as the dependent variable. Visual analysis of the results indicated that all participants required more prompted trials and sessions for the iPad/SGD condition. All participants learned a three step navigational sequence on the iPad. Participant preference probes were inconclusive and were not linked to speed of acquisition of requesting skills. Results suggest that both PECS and an iPad could be appropriate for teaching requesting skills to beginning communicators.

Using an adapted form of the picture exchange communication system to increase independent requesting in deafblind adults with learning disabilities.

PubMed

Bracken, Maeve; Rohrer, Nicole

2014-02-01

The current study assessed the effectiveness of an adapted form of the Picture Exchange Communication System (PECS) in increasing independent requesting in deafblind adults with learning disabilities. PECS cards were created to accommodate individual needs, including adaptations such as enlarging photographs and using swelled images which consisted of images created on raised line drawing paper. Training included up to Phase III of PECS and procedures ensuring generalizations across individuals and contexts were included. The effects of the intervention were evaluated using a multiple baseline design across participants. Results demonstrated an increase in independent requesting with each of the participants reaching mastery criterion. These results suggest that PECS, in combination with some minor adaptations, may be an effective communicative alternative for individuals who are deafblind and have learning impairments. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects on communicative requesting and speech development of the Picture Exchange Communication System in children with characteristics of autism.

PubMed

Ganz, Jennifer B; Simpson, Richard L

2004-08-01

Few studies on augmentative and alternative communication (AAC) systems have addressed the potential for such systems to impact word utterances in children with autism spectrum disorders (ASD). The Picture Exchange Communication System (PECS) is an AAC system designed specifically to minimize difficulties with communication skills experienced by individuals with ASD. The current study examined the role of PECS in improving the number of words spoken, increasing the complexity and length of phrases, and decreasing the non-word vocalizations of three young children with ASD and developmental delays (DD) with related characteristics. Participants were taught Phases 1-4 of PECS (i.e., picture exchange, increased distance, picture discrimination, and sentence construction). The results indicated that PECS was mastered rapidly by the participants and word utterances increased in number of words and complexity of grammar.

Humidity-dependent bacterial cells functional morphometry investigations using atomic force microscope.

PubMed

Nikiyan, Hike; Vasilchenko, Alexey; Deryabin, Dmitry

2010-01-01

The effect of a relative humidity (RH) in a range of 93-65% on morphological and elastic properties of Bacillus cereus and Escherichia coli cells was evaluated using atomic force microscopy. It is shown that gradual dehumidification of bacteria environment has no significant effect on cell dimensional features and considerably decreases them only at 65% RH. The increasing of the bacteria cell wall roughness and elasticity occurs at the same time. Observed changes indicate that morphological properties of B. cereus are rather stable in wide range of relative humidity, whereas E. coli are more sensitive to drying, significantly increasing roughness and stiffness parameters at RH

Effects of horticultural therapy on mood and heart rate in patients participating in an inpatient cardiopulmonary rehabilitation program.

PubMed

Wichrowski, Matthew; Whiteson, Jonathan; Haas, François; Mola, Ana; Rey, Mariano J

2005-01-01

To assess the effects of horticultural therapy (HT) on mood state and heart rate (HR) in patients participating in an inpatient cardiac rehabilitation program. Cardiac rehabilitation inpatients (n = 107) participated in the study. The HT group consisted of 59 subjects (34 males, 25 females). The control group, which participated in patient education classes (PECs), consisted of 48 subjects (31 males, 17 females). Both HT sessions and PEC are components of the inpatient rehabilitation program. Each group was evaluated before and after a class in their respective modality. Evaluation consisted of the completion of a Profile of Mood States (POMS) inventory, and an HR obtained by pulse oximetry. Changes in the POMS total mood disturbance (TMD) score and HR between preintervention and postintervention were compared between groups. There was no presession difference in either TMD score (16 +/- 3.6 and 19.0 +/- 3.2, PEC and HT, respectively) or HR (73.5 +/- 2.5 and 79 +/- 1.8, PEC and HT, respectively). Immediately following the intervention, the HT TMD was significantly reduced (post-TMD = 1.6 +/- 3.2, P < .001), while PEC TMD was not significantly changed (TMD = 17.0 +/- 28.5). After intervention, HR fell in HT by 4 +/- 9.6 bpm (P < .001) but was unchanged in PEC. These findings indicate that HT improves mood state, suggesting that it may be a useful tool in reducing stress. Therefore, to the extent that stress contributes to coronary heart disease, these findings support the role of HT as an effective component of cardiac rehabilitation.

Examination of the Source and Extended Virulence Genotypes of Escherichia coli Contaminating Retail Poultry Meat

PubMed Central

Johnson, Timothy J.; Logue, Catherine M.; Wannemuehler, Yvonne; Kariyawasam, Subhashinie; Doetkott, Curt; DebRoy, Chitrita; White, David G.

2009-01-01

Abstract Extraintestinal pathogenic Escherichia coli (ExPEC) are major players in human urinary tract infections, neonatal bacterial meningitis, and sepsis. Recently, it has been suggested that there might be a zoonotic component to these infections. To determine whether the E. coli contaminating retail poultry are possible extraintestinal pathogens, and to ascertain the source of these contaminants, they were assessed for their genetic similarities to E. coli incriminated in colibacillosis (avian pathogenic E. coli [APEC]), E. coli isolated from multiple locations of apparently healthy birds at slaughter, and human ExPEC. It was anticipated that the retail poultry isolates would most closely resemble avian fecal E. coli since only apparently healthy birds are slaughtered, and fecal contamination of carcasses is the presumed source of meat contamination. Surprisingly, this supposition proved incorrect, as the retail poultry isolates exhibited gene profiles more similar to APEC than to fecal isolates. These isolates contained a number of ExPEC-associated genes, including those associated with ColV virulence plasmids, and many belonged to the B2 phylogenetic group, known to be virulent in human hosts. Additionally, E. coli isolated from the crops and gizzards of apparently healthy birds at slaughter also contained a higher proportion of ExPEC-associated genes than did the avian fecal isolates examined. Such similarities suggest that the widely held beliefs about the sources of poultry contamination may need to be reassessed. Also, the presence of ExPEC-like clones on retail poultry meat means that we cannot yet rule out poultry as a source of ExPEC human disease. PMID:19580453

Effect of electro-acupuncture intervention on cognition attention bias in heroin addiction abstinence-a dot-probe-based event-related potential study.

PubMed

Jiang, Ying-Ping; Liu, Hao; Xu, Ping; Wang, Yan; Lu, Guang-Hua

2011-04-01

To study the changes of cognitive attention-related brain function in the heroin addicts before and after electro-acupuncture (EA) intervention for exploring the concerned neuro-mechanism of addictive relapse and the central action role of EA intervention. Adopting event-related potential (ERP) technique, the ERP at 64 electrode spots in 10 heroin addicts (test group) were recorded before and after EA intervention with dot-probe experimental form during implementing cognitive task on positive emotional clue (PEC), negative emotional clues (NEC), and heroin-related clue (HRC). The P200 amplitude components on the selected observation points (Fz, Cz, and Pz) were analyzed and compared with those obtained from 10 healthy subjects as the control. Before EA, the ERP of attention on HRC in the test group was higher than that on PEC and NEC (P<0.05) and significantly higher than that in the control group (P<0.05); after EA, the P200 amplitude of attention on HRC at Cz and Pz was significantly lowered (P<0.05) and that on PEC at Fz was significantly elevated (P<0.05). After EA, the P200 amplitude at Pz was ranked as NEC > PEC > HRC, but in the control group, it showed PEC > HRC at all three observation points and PEC > NEC at Pz. Heroin addicts show attention bias to HRC, which could be significantly reduced by EA intervention, illustrating that EA could effectively inhibit the attention bias to heroin and so might have potential for lowering the relapse rate.

PATHOGEN EQUIVALENCY COMMITTEE (PEC)

EPA Science Inventory

The U.S. Environmental Protection Agency created the PEC in 1985 to make recommendations to EPA and State managers on the equivalency of unproven sewage sludge disinfection technologies/processes to either a Process to Significantly Reduce Pathogens (PSRP) or a Process to Further...

The parietal epithelial cell: a key player in the pathogenesis of focal segmental glomerulosclerosis in Thy-1.1 transgenic mice.

PubMed

Smeets, Bart; Te Loeke, Nathalie A J M; Dijkman, Henry B P M; Steenbergen, Mark L M; Lensen, Joost F M; Begieneman, Mark P V; van Kuppevelt, Toin H; Wetzels, Jack F M; Steenbergen, Eric J

2004-04-01

Focal segmental glomerulosclerosis (FSGS) is a hallmark of progressive renal disease. Podocyte injury and loss have been proposed as the critical events that lead to FSGS. In the present study, the authors have examined the development of FSGS in Thy-1.1 transgenic (tg) mice, with emphasis on the podocyte and parietal epithelial cell (PEC). Thy-1.1 tg mice express the Thy-1.1 antigen on podocytes. Injection of anti-Thy-1.1 mAb induces an acute albuminuria and development of FSGS lesions that resemble human collapsing FSGS. The authors studied FSGS lesions at days 1, 3, 6, 7, 10, 14, and 21, in relation to changes in the expression of specific markers for normal podocytes (WT-1, synaptopodin, ASD33, and the Thy-1.1 antigen), for mouse PEC (CD10), for activated podocytes (desmin), for macrophages (CD68), and for proliferation (Ki-67). The composition of the extracellular matrix (ECM) that forms tuft adhesions or scars was studied using mAb against collagen IV alpha2 and alpha4 chains and antibodies directed against different heparan sulfate species. The first change observed was severe PEC injury at day 1, which increased in time, and resulted in denuded segments of Bowman's capsule at days 6 and 7. Podocytes showed foot process effacement and microvillous transformation. There was no evidence of podocyte loss or denudation of the GBM. Podocytes became hypertrophic at day 3, with decreased expression of ASD33 and synaptopodin and normal expression of WT-1 and Thy-1.1. Podocyte bridges were formed by attachment of hypertrophic podocytes to PEC and podocyte apposition against denuded segments of Bowman's capsule. At day 6, there was a marked proliferation of epithelial cells in Bowman's space. These proliferating cells were negative for desmin and all podocyte markers, but stained for CD10, and thus appeared to be PEC. The staining properties of the early adhesions were identical to that of Bowman's capsule, suggesting that the ECM in the adhesions was produced by PEC. In conclusion, the authors propose the following sequence of events leading to FSGS lesions in the Thy1.1 tg mice: (1) PEC damage and denudation of Bowman's capsule segments; (2) podocyte hypertrophy and bridging; and (3) PEC proliferation with ECM production.

PehN, a Polygalacturonase Homologue with a Low Hydrolase Activity, Is Coregulated with the Other Erwinia chrysanthemi Polygalacturonases

PubMed Central

Hugouvieux-Cotte-Pattat, Nicole; Shevchik, Vladimir E.; Nasser, William

2002-01-01

Erwinia chrysanthemi 3937 secretes an arsenal of pectinolytic enzymes, including at least eight endo-pectate lyases encoded by pel genes, which play a major role in the soft-rot disease caused by this bacterium on various plants. E. chrysanthemi also produces some hydrolases that cleave pectin. Three adjacent hydrolase genes, pehV, pehW, and pehX, encoding exo-poly-α-d-galacturonosidases, have been characterized. These enzymes liberate digalacturonides from the nonreducing end of pectin. We report the identification of a novel gene, named pehN, encoding a protein homologous to the glycosyl hydrolases of family 28, which includes mainly polygalacturonases. PehN has a low hydrolase activity on polygalacturonate and on various pectins. PehN action favors the activity of the secreted endo-pectate lyases, mainly PelB and PelC, and that of the periplasmic exo-pectate lyase PelX. However, removal of the pehN gene does not significantly alter the virulence of E. chrysanthemi. Regulation of pehN transcription was analyzed by using gene fusions. Like other pectinase genes, pehN transcription is dependent on several environmental conditions. It is induced by pectic catabolic products and is affected by growth phase, catabolite repression, osmolarity, anaerobiosis, nitrogen starvation, and the presence of calcium ions. The transcription of pehN is modulated by the repressor KdgR, which controls almost all the steps of pectin catabolism, and by cyclic AMP receptor protein (CRP), the global activator of sugar catabolism. The regulator PecS, which represses the transcription of the pel genes but activates that of pehV, pehW, and pehX, also activates transcription of pehN. The three regulators KdgR, PecS, and CRP act by direct interaction with the pehN promoter region. The sequences involved in the binding of these three regulators and of RNA polymerase have been precisely defined. Analysis of the simultaneous binding of these proteins indicates that CRP and RNA polymerase bind cooperatively and that the binding of KdgR could prevent pehN transcription. In contrast, the activator effect of PecS is not linked to competition with KdgR or to cooperation with CRP or RNA polymerase. This effect probably results from competition between PecS and an unidentified repressor involved in peh regulation. PMID:11976295

Effects of roughness and permeability on solute transfer at the sediment water interface.

PubMed

Han, Xu; Fang, Hongwei; He, Guojian; Reible, Danny

2018-02-01

Understanding the mechanisms of solute transfer across the sediment-water interface plays a crucial role in water quality prediction and management. In this study, different arranged particles are used to form typical rough and permeable beds. Large Eddy Simulation (LES) is used to model the solute transfer from the overlying water to sediment beds. Three rough wall turbulence regimes, i.e., smooth, transitional and rough regime, are separately considered and the effects of bed roughness on solute transfer are quantitatively analyzed. Results show that the classic laws related to Schmidt numbers can well reflect the solute transfer under the smooth regime with small roughness Reynolds numbers. Under the transitional regime, the solute transfer coefficient (K L + ) is enhanced and the effect of Schmidt number is weakened by increasing roughness Reynolds number. Under the rough regime, the solute transfer is suppressed by the transition layer (Brinkman layer) and controlled by the bed permeability. Moreover, it is found that water depth, friction velocity and bed permeability can be used to estimate the solute transfer velocity (K L ) under the completely rough regime. Copyright © 2017 Elsevier Ltd. All rights reserved.

Relaxed Manufacturing Design Tolerance Concepts. Volume 2. Appendices

DTIC Science & Technology

1977-07-01

are typical for such a part. A rough and finish pass is made to web thickness, a rough cut is made in the corners and then the stlf- fener walls...the programmed teed rate a little more on the second side due to having less material behind the web ; however, a designer usually provides for...Typical Survov Data Rocord Recommended Relaxation on Drawing Tolerances for Webs and Stiffcners Web Dimensional Deviation Occurrences vs. Stiffener

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, Xiaoyin; Lu, Ping; Fischer, Arthur J.

Illumination by a narrow-band laser has been shown to enable photoelectrochemical (PEC) etching of InGaN thin films into quantum dots with sizes controlled by the laser wavelength. Here, we investigate and elucidate the influence of solution pH on such quantum-size-controlled PEC etch process. We find that although a pH above 5 is often used for PEC etching of GaN-based materials, oxides (In 2O 3 and/or Ga 2O 3) form which interfere with quantum dot formation. Furthermore, at pH below 3, however, oxide-free QDs with self-terminated sizes can be successfully realized.

Compound effects of aging and experimental FSGS on glomerular epithelial cells.

PubMed

Schneider, Remington R S; Eng, Diana G; Kutz, J Nathan; Sweetwyne, Mariya T; Pippin, Jeffrey W; Shankland, Stuart J

2017-02-17

Advanced age portends a poorer prognosis in FSGS. To understand the impact of age on glomerular podocytes and parietal epithelial cells (PECs), experimental FSGS was induced in 3m-old mice (20-year old human age) and 27m-old mice (78-year old human age) by abruptly depleting podocytes with a cytopathic anti-podocyte antibody. Despite similar binding of the disease-inducing antibody, podocyte density was lower in aged FSGS mice compared to young FSGS mice. Activated PEC density was higher in aged versus young FSGS mice, as was the percentage of total activated PECs. Additionally, the percentage of glomeruli containing PECs with evidence of phosphorylated ERK and EMT was higher in aged FSGS mice. Extracellular matrix, measured by collagen IV and silver staining, was higher in aged FSGS mice along Bowman's capsule. However, collagen IV accumulation in the glomerular tufts alone and in glomeruli with both tuft and Bowman's capsule accumulation were similar in young FSGS and aged FSGS mice. Thus, the major difference in collagen IV staining in FSGS was along Bowman's capsule in aged mice. The significant differences in podocytes, PECs and extracellular matrix accumulation between young mice and old mice with FSGS might explain the differences in outcomes in FSGS based on age.

Compound effects of aging and experimental FSGS on glomerular epithelial cells

PubMed Central

Kutz, J. Nathan; Sweetwyne, Mariya T.; Pippin, Jeffrey W.; Shankland, Stuart J.

2017-01-01

Advanced age portends a poorer prognosis in FSGS. To understand the impact of age on glomerular podocytes and parietal epithelial cells (PECs), experimental FSGS was induced in 3m-old mice (20-year old human age) and 27m-old mice (78-year old human age) by abruptly depleting podocytes with a cytopathic anti-podocyte antibody. Despite similar binding of the disease-inducing antibody, podocyte density was lower in aged FSGS mice compared to young FSGS mice. Activated PEC density was higher in aged versus young FSGS mice, as was the percentage of total activated PECs. Additionally, the percentage of glomeruli containing PECs with evidence of phosphorylated ERK and EMT was higher in aged FSGS mice. Extracellular matrix, measured by collagen IV and silver staining, was higher in aged FSGS mice along Bowman's capsule. However, collagen IV accumulation in the glomerular tufts alone and in glomeruli with both tuft and Bowman's capsule accumulation were similar in young FSGS and aged FSGS mice. Thus, the major difference in collagen IV staining in FSGS was along Bowman's capsule in aged mice. The significant differences in podocytes, PECs and extracellular matrixaccumulation between young mice and old mice with FSGS might explain the differences in outcomes in FSGS based on age. PMID:28222042

Effect of pectin charge density on formation of multilayer films with chitosan.

PubMed

Kamburova, Kamelia; Milkova, Viktoria; Petkanchin, Ivana; Radeva, Tsetska

2008-04-01

The effect of pectin charge density on the formation of multilayer films with chitosan (PEC/CHI) is studied by means of electro-optics. Pectins of low (21%) and high (71%) degrees of esterification, which are inversely proportional to the pectin charge density, are used to form films on colloidal beta-FeOOH particles at pH 4.0 when the CHI is fully ionized. We find that, after deposition of the first 3-4 layers, the film thickness increases linearly with the number of adsorbed layers. However, the increase in the film thickness is larger when the film is terminated with CHI. Irregular increase of the film thickness is more marked for the PEC with higher density of charge. Oscillation in the electrical polarizability of the film-coated particles with the number of deposited layers is also registered in the PEC/CHI films. The charge balance of the multilayers, calculated from electrical polarizability of the film-coated particles, is positive, with larger excess of positive charge within the film constructed from CHI and less charged PEC. This is attributed to the ability of CHI to diffuse into the film at each deposition step. Despite the CHI diffusion, the film thickness increases linearly due to the dissolution of unstable PEC/CHI complexes from the film surface.

Growth of β-Ga2O3 and GaN nanowires on GaN for photoelectrochemical hydrogen generation.

PubMed

Hwang, Jih-Shang; Liu, Tai-Yan; Chattopadhyay, Surjit; Hsu, Geng-Ming; Basilio, Antonio M; Chen, Han-Wei; Hsu, Yu-Kuei; Tu, Wen-Hsun; Lin, Yan-Gu; Chen, Kuei-Hsien; Li, Chien-Cheng; Wang, Sheng-Bo; Chen, Hsin-Yi; Chen, Li-Chyong

2013-02-08

Enhanced photoelectrochemical (PEC) performances of Ga(2)O(3) and GaN nanowires (NWs) grown in situ from GaN were demonstrated. The PEC conversion efficiencies of Ga(2)O(3) and GaN NWs have been shown to be 0.906% and 1.09% respectively, in contrast to their 0.581% GaN thin film counterpart under similar experimental conditions. A low crystallinity buffer layer between the grown NWs and the substrate was found to be detrimental to the PEC performance, but the layer can be avoided at suitable growth conditions. A band bending at the surface of the GaN NWs generates an electric field that drives the photogenerated electrons and holes away from each other, preventing recombination, and was found to be responsible for the enhanced PEC performance. The enhanced PEC efficiency of the Ga(2)O(3) NWs is aided by the optical absorption through a defect band centered 3.3 eV above the valence band of Ga(2)O(3). These findings are believed to have opened up possibilities for enabling visible absorption, either by tailoring ion doping into wide bandgap Ga(2)O(3) NWs, or by incorporation of indium to form InGaN NWs.

CDC42 is required for epicardial and pro-epicardial development by mediating FGF receptor trafficking to the plasma membrane.

PubMed

Li, Jingjing; Miao, Lianjie; Zhao, Chen; Shaikh Qureshi, Wasay Mohiuddin; Shieh, David; Guo, Hua; Lu, Yangyang; Hu, Saiyang; Huang, Alice; Zhang, Lu; Cai, Chen-Leng; Wan, Leo Q; Xin, Hongbo; Vincent, Peter; Singer, Harold A; Zheng, Yi; Cleaver, Ondine; Fan, Zhen-Chuan; Wu, Mingfu

2017-05-01

The epicardium contributes to multiple cardiac lineages and is essential for cardiac development and regeneration. However, the mechanism of epicardium formation is unclear. This study aimed to establish the cellular and molecular mechanisms underlying the dissociation of pro-epicardial cells (PECs) from the pro-epicardium (PE) and their subsequent translocation to the heart to form the epicardium. We used lineage tracing, conditional deletion, mosaic analysis and ligand stimulation in mice to determine that both villous protrusions and floating cysts contribute to PEC translocation to myocardium in a CDC42-dependent manner. We resolved a controversy by demonstrating that physical contact of the PE with the myocardium constitutes a third mechanism for PEC translocation to myocardium, and observed a fourth mechanism in which PECs migrate along the surface of the inflow tract to reach the ventricles. Epicardial-specific Cdc42 deletion disrupted epicardium formation, and Cdc42 null PECs proliferated less, lost polarity and failed to form villous protrusions and floating cysts. FGF signaling promotes epicardium formation in vivo , and biochemical studies demonstrated that CDC42 is involved in the trafficking of FGF receptors to the cell membrane to regulate epicardium formation. © 2017. Published by The Company of Biologists Ltd.

Electrochemical synthesis of nanoporous tungsten carbide and its application as electrocatalysts for photoelectrochemical cells.

PubMed

Kang, Jin Soo; Kim, Jin; Lee, Myeong Jae; Son, Yoon Jun; Jeong, Juwon; Chung, Dong Young; Lim, Ahyoun; Choe, Heeman; Park, Hyun S; Sung, Yung-Eun

2017-05-04

Photoelectrochemical (PEC) cells are promising tools for renewable and sustainable solar energy conversion. Currently, their inadequate performance and high cost of the noble metals used in the electrocatalytic counter electrode have postponed the practical use of PEC cells. In this study, we report the electrochemical synthesis of nanoporous tungsten carbide and its application as a reduction catalyst in PEC cells, namely, dye-sensitized solar cells (DSCs) and PEC water splitting cells, for the first time. The method employed in this study involves the anodization of tungsten foil followed by post heat treatment in a CO atmosphere to produce highly crystalline tungsten carbide film with an interconnected nanostructure. This exhibited high catalytic activity for the reduction of cobalt bipyridine species, which represent state-of-the-art redox couples for DSCs. The performance of tungsten carbide even surpassed that of Pt, and a substantial increase (∼25%) in energy conversion efficiency was achieved when Pt was substituted by tungsten carbide film as the counter electrode. In addition, tungsten carbide displayed decent activity as a catalyst for the hydrogen evolution reaction, suggesting the high feasibility for its utilization as a cathode material for PEC water splitting cells, which was also verified in a two-electrode water photoelectrolyzer.

Effects of exposure to dietary chromium on tissue mineral contents in rats fed diets with fiber.

PubMed

Prescha, Anna; Krzysik, Monika; Zabłocka-Słowińska, Katarzyna; Grajeta, Halina

2014-06-01

This study evaluated the effects of diets with fiber (cellulose and/or pectin) supplemented with chromium(III) on homeostasis of selected minerals in femurs, thigh muscles, livers, and kidneys of rats. For 6 weeks, male rats were fed experimental diets: a fiber-free diet (FF), a diet containing 5% cellulose (CEL), 5% pectin (PEC), or 2.5% cellulose and 2.5% pectin (CEL+PEC). These diets had 2.53 or 0.164 mg Cr/kg diet. The tissue levels of Ca, Mg, Zn, Fe, and Cr were determined by using atomic absorption spectrometry. Supplementing diets with Cr resulted in significantly higher Cr levels in the femurs of rats fed the CEL diet and significantly higher Cr and Fe levels in the rats fed the CEL+PEC diet compared to the rats fed FF diet. Muscle Ca content was significantly lower in the rats fed the CEL+PEC+Cr diet compared to the rats fed FF+Cr diet. The rats consuming the PEC+Cr diet had the highest liver Cr content. The highest kidney Zn content was observed in the rats fed diets containing Cr and one type of fiber. These results indicate that diets containing chromium at elevated dose and fiber have a significant effect on the mineral balance in rat tissues.

Extraintestinal Pathogenic and Antimicrobial-Resistant Escherichia coli, Including Sequence Type 131 (ST131), from Retail Chicken Breasts in the United States in 2013

PubMed Central

Porter, Stephen B.; Johnston, Brian; Thuras, Paul; Clock, Sarah; Crupain, Michael; Rangan, Urvashi

2017-01-01

ABSTRACT Chicken meat products are hypothesized to be vehicles for transmitting antimicrobial-resistant and extraintestinal pathogenic Escherichia coli (ExPEC) to consumers. To reassess this hypothesis in the current era of heightened concerns about antimicrobial use in food animals, we analyzed 175 chicken-source E. coli isolates from a 2013 Consumer Reports national survey. Isolates were screened by PCR for ExPEC-defining virulence genes. The 25 ExPEC isolates (12% of 175) and a 2:1 randomly selected set of 50 non-ExPEC isolates were assessed for their phylogenetic/clonal backgrounds and virulence genotypes for comparison with their resistance profiles and the claims on the retail packaging label (“organic,” “no antibiotics,” and “natural”). Compared with the findings for non-ExPEC isolates, the group of ExPEC isolates had a higher prevalence of phylogroup B2 isolates (44% versus 4%; P < 0.001) and a lower prevalence of phylogroup A isolates (4% versus 30%; P = 0.001), a higher prevalence of multiple individual virulence genes, higher virulence scores (median, 11 [range, 4 to 16] versus 8 [range, 1 to 14]; P = 0.001), and higher resistance scores (median, 4 [range, 0 to 8] versus 3 [range, 0 to 10]; P < 0.001). All five isolates of sequence type 131 (ST131) were ExPEC (P = 0.003), were as extensively resistant as the other isolates tested, and had higher virulence scores than the other isolates tested (median, 12 [range, 11 to 13] versus 8 [range, 1 to 16]; P = 0.005). Organic labeling predicted lower resistance scores (median, 2 [range, 0 to 3] versus 4 [range, 0 to 10]; P = 0.008) but no difference in ExPEC status or virulence scores. These findings document a persisting reservoir of extensively antimicrobial-resistant ExPEC isolates, including isolates from ST131, in retail chicken products in the United States, suggesting a potential public health threat. IMPORTANCE We found that among Escherichia coli isolates from retail chicken meat products purchased across the United States in 2013 (many of these isolates being extensively antibiotic resistant), a minority had genetic profiles suggesting an ability to cause extraintestinal infections in humans, such as urinary tract infection, implying a risk of foodborne disease. Although isolates from products labeled “organic” were less extensively antibiotic resistant than other isolates, they did not appear to be less virulent. These findings suggest that retail chicken products in the United States, even if they are labeled “organic,” pose a potential health threat to consumers because they are contaminated with extensively antibiotic-resistant and, presumably, virulent E. coli isolates. PMID:28062464

Numerical Simulation of Roughness-Induced Transient Growth in a Laminar Boundary Layer

NASA Technical Reports Server (NTRS)

Fischer, Paul; Choudhari, Meelan

2004-01-01

Numerical simulations are used to examine the roughness-induced transient growth in a laminar boundary-layer flow. Based on the spectral element method, these simulations model the stationary disturbance field associated with a nonsmooth roughness geometry, such as the spanwise periodic array of circular disks used by White and co-workers during a series of wind tunnel experiments at Case Western Reserve University. Besides capturing the major trends from the recent measurements by White and Ergin, the simulations provide additional information concerning the relative accuracy of the experimental findings derived from two separate wall-finding procedures. The paper also explores the dependence of transient growth on geometric characteristics of the roughness distribution, including the height and planform shape of the roughness element and the ratio of roughness due to spacing between an adjacent pair of elements. Results are used for a preliminary assessment of the differences between recently reported theoretical results of Tumin and Reshotko and the measurements by White and Ergin.

Experimental Investigation of Average Heat-Transfer and Friction Coefficients for Air Flowing in Circular Tubes Having Square-Thread-Type Roughness

NASA Technical Reports Server (NTRS)

Sams, E. W.

1952-01-01

An investigation of forced-convection heat transfer and associated pressure drops was conducted with air flowing through electrically heated Inconel tubes having various degrees of square-thread-type roughness, an inside diameter of 1/2 inch, and a length of 24 inches. were obtained for tubes having conventional roughness ratios (height of thread/radius of tube) of 0 (smooth tube), 0.016, 0.025, and 0.037 over ranges of bulk Reynolds numbers up to 350,000, average inside-tube-wall temperatures up to 1950deg R, and heat-flux densities up to 115,000 Btu per hour per square foot. Data The experimental data showed that both heat transfer and friction increased with increase in surface roughness, becoming more pronounced with increase in Reynolds number; for a given roughness, both heat transfer and friction were also influenced by the tube wall-to-bulk temperature ratio. Good correlation of the heat-transfer data for all the tubes investigated was obtained by use of a modification of the conventional Nusselt correlation parameters wherein the mass velocity in the Reynolds number was replaced by the product of air density evaluated at the average film temperature and the so-called friction velocity; in addition, the physical properties of air were evaluated at the average film temperature. The isothermal friction data for the rough tubes, when plotted in the conventional manner, resulted in curves similar to those obtained by other investigators; that is, the curve for a given roughness breaks away from the Blasius line (representing turbulent flow in smooth tubes) at some value of Reynolds number, which decreases with increase in surface roughness, and then becomes a horizontal line (friction coefficient independent of Reynolds number). A comparison of the friction data for the rough tubes used herein indicated that the conventional roughness ratio is not an adequate measure of relative roughness for tubes having a square-thread-type element. The present data, as well as those of other investigators, were used to isolate the influence of ratios of thread height to width, thread spacing to width, and the conventional roughness ratio on the friction coefficient. A fair correlation of the friction data was obtained for each tube with heat addition when the friction coefficient and Reynolds number were defined on the basis of film properties; however, the data for each tube retained the curve characteristic of that particular roughness. The friction data for all the rough tubes could be represented by a single line for the complete turbulence region by incorporating a roughness parameter in the film correlation. No correlation was obtained for the region of incomplete turbulence.

Analytical skin friction and heat transfer formula for compressible internal flows

NASA Technical Reports Server (NTRS)

Dechant, Lawrence J.; Tattar, Marc J.

1994-01-01

An analytic, closed-form friction formula for turbulent, internal, compressible, fully developed flow was derived by extending the incompressible law-of-the-wall relation to compressible cases. The model is capable of analyzing heat transfer as a function of constant surface temperatures and surface roughness as well as analyzing adiabatic conditions. The formula reduces to Prandtl's law of friction for adiabatic, smooth, axisymmetric flow. In addition, the formula reduces to the Colebrook equation for incompressible, adiabatic, axisymmetric flow with various roughnesses. Comparisons with available experiments show that the model averages roughly 12.5 percent error for adiabatic flow and 18.5 percent error for flow involving heat transfer.

JPRS Report, East Europe.

DTIC Science & Technology

1990-04-06

Andrasfalvy 2 Pecs Zoltan Trombitas Sandor Szeles Mrs. Kaposi, Dr. -Andras Pap Sandor Gyulai; Maria Dunai Jozsef Kuller; Dr. Istvan Marton 3 Pecs Dr. Andrea ...Csizmadia Mrs. Szabo, Erzsebet Kovacs 5 Varpalota Peter Patonai Laszlo Czifra Janos Csovari Janos Kovacs Ferenc Schmidt Tibor Fakasz 6 Veszprem -Ferenc

Influence of packing density and surface roughness of vertically-aligned carbon nanotubes on adhesive properties of gecko-inspired mimetics.

PubMed

Chen, Bingan; Zhong, Guofang; Oppenheimer, Pola Goldberg; Zhang, Can; Tornatzky, Hans; Esconjauregui, Santiago; Hofmann, Stephan; Robertson, John

2015-02-18

We have systematically studied the macroscopic adhesive properties of vertically aligned nanotube arrays with various packing density and roughness. Using a tensile setup in shear and normal adhesion, we find that there exists a maximum packing density for nanotube arrays to have adhesive properties. Too highly packed tubes do not offer intertube space for tube bending and side-wall contact to surfaces, thus exhibiting no adhesive properties. Likewise, we also show that the surface roughness of the arrays strongly influences the adhesion properties and the reusability of the tubes. Increasing the surface roughness of the array strengthens the adhesion in the normal direction, but weakens it in the shear direction. Altogether, these results allow progress toward mimicking the gecko's vertical mobility.

Numerical investigation on the performance of fin and tube heat exchangers using rectangular vortex generators

NASA Astrophysics Data System (ADS)

Zeeshan, Mohd; Hazarika, Saheera Azmi; Nath, Sujit; Bhanja, Dipankar

2017-07-01

In the present work, a 3-D numerical investigation has been performed to explore the effect of attack angles on the thermal-hydraulic performance of fin and tube heat exchanger (FTHE) using rectangular winglet pairs (RWPs). RWPs are placed adjacent to the tubes and three attack angels are considered for the study i.e. 5°, 15° and 25°. The effect of attack angles are examined on the heat transfer characteristics as well as in pressure drop penalty with airside Reynolds number Rea ranges from 500 to 900. Two performance evaluation criteria namely PEC1 i.e. area goodness factor (j/f) and PEC2 i.e. heat transfer rate per unit fan power consumption (Q/Pf) are considered for the performance evaluation. Furthermore, MOORA method is applied to obtain the performance order of FTHE configurations by taking PEC1 and PEC2 as beneficial attributes and fan power Pf as a non-beneficial attribute, keeping equal importance to each attribute. The results show that 5° attack angle provides the better performance in terms of PEC1 as heat transfer coefficient is increased by 27.70% at Rea=500 and 32.73% at Rea=900 respectively with 13.01% increased pressure drop penalty at Rea=500 and 14.26% at Rea=900 respectively. In terms of PEC2, though the 5° attack angle provides the high values of Q/Pf factor among the 15° and 25° attack angles, but it is found insignificant to replace the baseline configuration i.e. plain fin and tube heat exchanger configuration without vortex generators. Moreover, in MOORA optimization analysis also, it is found that 5° attack angle provides the better thermal-hydraulic performance.

Cyt toxin expression reveals an inverse regulation of insect and plant virulence factors of Dickeya dadantii.

PubMed

Costechareyre, Denis; Dridi, Bedis; Rahbé, Yvan; Condemine, Guy

2010-12-01

The plant pathogenic bacteria Dickeya dadantii is also a pathogen of the pea aphid Acyrthosiphon pisum. The genome of the bacteria contains four cyt genes, encoding homologues of Bacillus thuringiensis Cyt toxins, which are involved in its pathogenicity to insects. We show here that these genes are transcribed as an operon, and we determined the conditions necessary for their expression. Their expression is induced at high temperature and at an osmolarity equivalent to that found in the plant phloem sap. The regulators of cyt genes have also been identified: their expression is repressed by H-NS and VfmE and activated by PecS. These genes are already known to regulate plant virulence factors, but in an opposite way. When tested in a virulence assay by ingestion, the pecS mutant was almost non-pathogenic while hns and vfmE mutants behaved in the same way as the wild-type strain. Mutants of other regulators of plant virulence, GacA, OmpR and PhoP, that do not control Cyt toxin production, also showed reduced pathogenicity. In an assay by injection of bacteria, the gacA strain was less pathogenic but, surprisingly, the pecS mutant was slightly more virulent. These results show that Cyt toxins are not the only virulence factors required to kill aphids, and that these factors act at different stages of the infection. Moreover, their production is controlled by general virulence regulators known for their role in plant virulence. This integration could indicate that virulence towards insects is a normal mode of life for D. dadantii. © 2010 Society for Applied Microbiology and Blackwell Publishing Ltd.

Increase of heat-shock protein and induction of gamma/delta T cells in peritoneal exudate of mice after injection of live Fusobacterium nucleatum.

PubMed Central

Saito, K; Katsuragi, H; Mikami, M; Kato, C; Miyamaru, M; Nagaso, K

1997-01-01

Fusobacterium nucleatum and Actinobacillus actinomycetemcomitans are Gram-negative rod periodontal pathogens. The peritoneal cavity of Institute of Cancer Research (ICR) mice was used as the local infection model. In vivo production of heat-shock proteins (hsp) was studied by injection of 1/10 minimum lethal dose (MLD) of each live bacteria into mice. Heat-shock proteins 70 and 60 were examined in the extract of peritoneal exudate cells (PEC) from mice injected intraperitoneally with either F. nucleatum or A. actinomycetemcomitans by using sodium dodecylsulphate-polyacrylamide gel electrophoresis and immunoblotting analysis. Although hsp are present in PEC without injection of the bacteria, both hsp increased and reached a peak on day 3 after F. nucleatum injection but not after A. actinomycetemcomitans. Kinetic study of gamma/delta cells in PEC after injection of bacteria showed that the increase of gamma/delta T cells was observed only in the PEC from mice injected with F. nucleatum but not A. actinomycetemcomitans. The gamma/delta T cells in PEC were either CD3+ and CD4+ or CD3+ and CD8+. The differential cell count of PEC suggested that gamma/delta T-cell induction is related to the expansion of the macrophage population. The phagocytic and chemiluminescence responses of macrophages against the same bacteria were compared after intensive immunization with live F. nucleatum and A. actinomycetemcomitans. Elevations of chemiluminescence response and phagocytic function by immunization were observed in the macrophages of mice immunized with F. nucleatum. These results suggest the sequential appearance of hsp, gamma/delta T cells and macrophage activation after fusobacterial infection. Images Figure 2 PMID:9135551

Effect of counterface roughness on the friction of bionic wall-shaped microstructures for gecko-like attachments.

PubMed

Kasem, Haytam; Cohen, Yossi

2017-08-04

Hairy adhesive systems involved in gecko locomotion have drawn the interest of many researchers regarding the development of bionic solutions for fast and reversible adhesive technologies. To date, despite extensive efforts to design gecko-inspired adhesive surfaces, adhesion and friction capacities are often evaluated using smooth and rigid counterfaces, in general glass, whereas most natural and artificial surfaces inevitably have a certain level of roughness. For that reason, in this study experiments tested the effects of the substrate roughness on the friction of bionic wale-shaped microstructures for gecko-like attachments. To this end, 12 substrates with different isotropic roughness were prepared using the same Epoxy material. Friction force was measured under various normal loads. It was concluded that classical roughness parameters, considered separately, are not appropriate to explain roughness-related variations in friction force. This has led us to develop a new integrative roughness parameter that combines characteristics of the surface. The parameter is capable of classifying the obtained experimental results in a readable way. An analytical model based on the experimental results has been developed to predict the variation of the friction force as a function of counterface roughness and applied normal load.

Problems And Their Solutions When Thin-Walled Turned Parts Of High Precision With Quasi-Optical Surfaces Are Manufactured On A CNC Automatic Lathe Under Workshop Conditions

NASA Astrophysics Data System (ADS)

Jaeger, Valentin E.

1989-04-01

The geometrical accuracy and surface roughness of diamond-turned workpieces is influenced by several parameters: the properties of the machine tool, the cutting process and the environmental conditions. A thin-walled electrode made from an aluminium alloy (wall thickness: 1 mm, length: 169 mm, outer diameter: 126 mm) and intended for an electrostatic measuring instrument, serves as an example to show how quasi-optical surfaces with a surface roughness Rα < 10 nm and deviations from roundness of <= 5 μm can be achieved when some of these influence quantities are optimized. The cylindrical part of the electrode was turned by means of a rounded mirror-finish diamond tool, the width of the cutting edge being 2 mm, the rake angle -6° and the clearance angle 2°. Compliance with the tolerances of geometrical accuracy was particularly difficult. As age-hardened wrought aluminium alloys cannot be stress-relieved by annealing, or only insufficiently, the geometrical accuracy - in particular the roundness - of thin-walled, rotationally symmetric bodies decisively depends on the state of stress of the workpiece material, on the clamping fixture and on the balanced condition of this clamping fixture.

Steady Boundary Layer Disturbances Created By Two-Dimensional Surface Ripples

NASA Astrophysics Data System (ADS)

Kuester, Matthew

2017-11-01

Multiple experiments have shown that surface roughness can enhance the growth of Tollmien-Schlichting (T-S) waves in a laminar boundary layer. One of the common observations from these studies is a ``wall displacement'' effect, where the boundary layer profile shape remains relatively unchanged, but the origin of the profile pushes away from the wall. The objective of this work is to calculate the steady velocity field (including this wall displacement) of a laminar boundary layer over a surface with small, 2D surface ripples. The velocity field is a combination of a Blasius boundary layer and multiple disturbance modes, calculated using the linearized Navier-Stokes equations. The method of multiple scales is used to include non-parallel boundary layer effects of O (Rδ- 1) ; the non-parallel terms are necessary, because a wall displacement is mathematically inconsistent with a parallel boundary layer assumption. This technique is used to calculate the steady velocity field over ripples of varying height and wavelength, including cases where a separation bubble forms on the leeward side of the ripple. In future work, the steady velocity field will be the input for stability calculations, which will quantify the growth of T-S waves over rough surfaces. The author would like to acknowledge the support of the Kevin T. Crofton Aerospace & Ocean Engineering Department at Virginia Tech.

FROM CONCEPT TO EQUIVALENCY: THE 503 REGULATIONS AND THE PATHOGEN EQUIVALENCY COMMITTEE

EPA Science Inventory

Since its creation in 1985, the Pathogen Equivalency Committee (PEC) has been reviewing innovative and alternative sludge disinfection technologies with regards to their abilities to protect human health and the environment. The PEC is charged to make recommendations on whether t...

Photoelectrochemical Solar Cells.

ERIC Educational Resources Information Center

McDevitt, John T.

1984-01-01

This introduction to photoelectrochemical (PEC) cells reviews topics pertaining to solar energy conversion and demonstrates the ease with which a working PEC cell can be prepared with n-type silicon as the photoanode and a platinum counter electrode (both immersed in ethanolic ferrocene/ferricenium solutions). Experiments using the cell are…

Efficient carbon dots/NiFe-layered double hydroxide/BiVO4 photoanodes for photoelectrochemical water splitting

NASA Astrophysics Data System (ADS)

Lv, Xiaowei; Xiao, Xin; Cao, Minglei; Bu, Yi; Wang, Chuanqing; Wang, Mingkui; Shen, Yan

2018-05-01

Modification of semiconductor photoanodes with oxygen evolution catalyst (OEC) is an effective approach for improving photoelectrochemical (PEC) water splitting efficiency. In the configuration, how to increase the activity of OEC is crucial to further improve PEC performance. Herein, a ternary photoanode system was designed to enhance PEC efficiency of photoelectrodes through introducing carbon dots (CDs), NiFe-layered double hydroxide (NiFe-LDH) nanosheets on BiVO4 particles. Systematic research shows that NiFe-LDH serves as an OEC which accelerates oxygen evolution kinetics, while the introduction of CDs can further reduce charge transfer resistance and overpotential for oxygen evolution. Under the synergistic effect of NiFe-LDH and CDs, the photocurrent and incident photon to current conversion efficiency (IPCE) of the resulting CDs/NiFe-LDH/BiVO4 photoanode is improved significantly than those of the NiFe-LDH/BiVO4 electrode. Consequently, such a ternary heterostructure could be an alternative way to further enhance PEC water splitting performance.

Bloating in (Pb0.95Sn0.05Te)0.92(PbS)0.08-0.055%PbI2 Thermoelectric Specimens as a Result of Processing Conditions

NASA Astrophysics Data System (ADS)

Ni, Jennifer E.; Case, Eldon D.; Stewart, Ryan; Wu, Chun-I.; Hogan, Timothy P.; Kanatzidis, Mercouri G.

2012-06-01

Lead chalcogenides such as (Pb0.95Sn0.05Te)0.92(PbS)0.08-0.055%PbI2 have received attention due to their encouraging thermoelectric properties. For the hot pressing (HP) and pulsed electric current sintering (PECS) techniques used in this study, decomposition reactions can generate porosity (bloating). Porosity in turn can degrade electrical, thermal, and mechanical properties. In this study, microstructural observations (scanning electron microscopy) and room-temperature elasticity measurements (resonant ultrasound spectroscopy) were used to characterize bloating generated during post-densification anneals. Although every HP specimen bloated during post-densification annealing, no bloating was observed for the PECS specimens processed from dry milled only powders. The lack of bloating for the annealed PECS specimens may be related to the electrical discharge intrinsic in the PECS process, which reportedly cleans the powder particle surfaces during densification.

Multifunctional nanoparticulate polyelectrolyte complexes.

PubMed

Hartig, Sean M; Greene, Rachel R; DasGupta, Jayasri; Carlesso, Gianluca; Dikov, Mikhail M; Prokop, Ales; Davidson, Jeffrey M

2007-12-01

Water-soluble, biodegradable, polymeric, polyelectrolyte complex dispersions (PECs) have evolved because of the limitations, in terms of toxicity, of the currently available systems. These aqueous nanoparticulate architectures offer a significant advantage for products that may be used as drug delivery systems in humans. PECs are created by mixing oppositely charged polyions. Their hydrodynamic diameter, surface charge, and polydispersity are highly dependent on concentration, ionic strength, pH, and molecular parameters of the polymers that are used. In particular, the complexation between polyelectrolytes with significantly different molecular weights leads to the formation of water-insoluble aggregates. Several PEC characteristics are favorable for cellular uptake and colloidal stability, including hydrodynamic diameter less than 200 nm, surface charge of >30 mV or <-30 mV, spherical morphology, and polydispersity index (PDI) indicative of a homogeneous distribution. Maintenance of these properties is critical for a successful delivery vehicle. This review focuses on the development and potential applications of PECs as multi-functional, site-specific nanoparticulate drug/gene delivery and imaging devices.

Dual role of TiO2 buffer layer in Pt catalyzed BiFeO3 photocathodes: Efficiency enhancement and surface protection

NASA Astrophysics Data System (ADS)

Shen, Huanyu; Zhou, Xiaoxue; Dong, Wen; Su, Xiaodong; Fang, Liang; Wu, Xi; Shen, Mingrong

2017-09-01

Polycrystalline ferroelectric BiFeO3 (BFO) films deposited on transparent indium tin oxide (ITO) electrodes have shown to be an interesting photocathode for photoelectrochemical (PEC) water splitting; however, its PEC performance and stability are far from perfection. Herein, we reported an amorphous TiO2 buffer layer, inserted between BFO and Pt catalyst, improves significantly both its PEC activity and stability. A photocathodic current density of -460 μA/cm2 at 0 V vs. reversible hydrogen electrode (RHE) and an onset potential of 1.25 V vs. RHE were obtained in ITO/BFO/TiO2/Pt photocathode under 100 mW/cm2 Xe-lamp illumination. TiO2 functions as a buffer layer to remove the upward barrier between BFO and Pt, and makes the photogenerated carriers separate efficiently. The photocathode also shows high stability in acid solution after a 10-h PEC continuous testing.

Osteoinductive activity of insulin-functionalized cell culture surfaces obtained using diazonium chemistry

NASA Astrophysics Data System (ADS)

Mikulska, Anna; Filipowska, Joanna; Osyczka, Anna; Nowakowska, Maria; Szczubiałka, Krzysztof

2014-12-01

Polymeric surfaces suitable for cell culture (DR/Pec) were constructed from diazoresin (DR) and pectin (Pec) in a form of ultrathin films using the layer-by-layer (LbL) technique. The surfaces were functionalized with insulin using diazonium chemistry. Such functionalized surfaces were used to culture human mesenchymal stem cells (hMSCs) to assess their suitability for bone tissue engineering and regeneration. The activity of insulin immobilized on the surfaces (DR/Pec/Ins) was compared to that of insulin dissolved in the culture medium. Human MSC grown on insulin-immobilized DR/Pec surfaces displayed increased proliferation and higher osteogenic activity. The latter was determined by means of alkaline phosphatase (ALP) activity, which increases at early stages of osteoblasts differentiation. Insulin dissolved in the culture medium did not stimulate cell proliferation and its osteogenic activity was significantly lower. Addition of recombinant human bone morphogenetic protein 2 (rhBMP-2) to the culture medium further increased ALP activity in hMSCs indicating additive osteogenic action of immobilized insulin and rhBMP-2

Formation of polyelectrolyte complexes with diethylaminoethyl dextran: charge ratio and molar mass effect.

PubMed

Le Cerf, Didier; Pepin, Anne Sophie; Niang, Pape Momar; Cristea, Mariana; Karakasyan-Dia, Carole; Picton, Luc

2014-11-26

The formation of polyelectrolyte complexes (PECs) between carboxymethyl pullulan and DEAE Dextran, was investigated, in dilute solution, with emphasis on the effect of charge density (molar ratio or pH) and molar masses. Electrophoretic mobility measurements have evidenced that insoluble PECs (neutral electrophoretic mobility) occurs for charge ratio between 0.6 (excess of polycation) and 1 (stoichiometry usual value) according to the pH. This atypical result is explained by the inaccessibility of some permanent cationic charge when screened by pH dependant cationic ones (due to the Hoffman alkylation). Isothermal titration calorimetry (ITC) indicates an endothermic formation of PEC with a binding constant around 10(5) L mol(-1). Finally asymmetrical flow field flow fractionation coupled on line with static multi angle light scattering (AF4/MALS) evidences soluble PECs with very large average molar masses and size around 100 nm, in agreement with scrambled eggs multi-association between various polyelectrolyte chains. Copyright © 2014 Elsevier Ltd. All rights reserved.

Influence of processing parameters on pore structure of 3D porous chitosan-alginate polyelectrolyte complex scaffolds.

PubMed

Florczyk, Stephen J; Kim, Dae-Joon; Wood, David L; Zhang, Miqin

2011-09-15

Fabrication of porous polymeric scaffolds with controlled structure can be challenging. In this study, we investigated the influence of key experimental parameters on the structures and mechanical properties of resultant porous chitosan-alginate (CA) polyelectrolyte complex (PEC) scaffolds, and on proliferation of MG-63 osteoblast-like cells, targeted at bone tissue engineering. We demonstrated that the porous structure is largely affected by the solution viscosity, which can be regulated by the acetic acid and alginate concentrations. We found that the CA PEC solutions with viscosity below 300 Pa.s yielded scaffolds of uniform pore structure and that more neutral pH promoted more complete complexation of chitosan and alginate, yielding stiffer scaffolds. CA PEC scaffolds produced from solutions with viscosities below 300 Pa.s also showed enhanced cell proliferation compared with other samples. By controlling the key experimental parameters identified in this study, CA PEC scaffolds of different structures can be made to suit various tissue engineering applications. Copyright © 2011 Wiley Periodicals, Inc.

Enhanced photoelectrochemical performance of TiO2 nanotube arrays with coexisted Pt nanoparticles and Co-Pi cocatalysts

NASA Astrophysics Data System (ADS)

Li, Yanfang; Cao, Chang; Xie, Xinxin; Zhang, Li; Lin, Shiwei

2018-04-01

Highly-ordered TiO2 nanotube arrays (TNTAs) were prepared by electrochemical anodization. Cobalt-phosphate (Co-Pi) film fabricated by electrodeposition and Pt nanoparticles (Pt NPs) fabricated by photochemical reduction were decorated onto TNTAs to enhance the photoelectrochemical (PEC) performance together. The photocurrent density of the TNTAs/Co-Pi/Pt photoelectrode could reach 0.185 mA/cm2 at 1.23 V versus reversible hydrogen electrode under UV lamp illumination (1 mW/cm2), which is 2.65 times compared to that of the pure TNTAs photoelectrode. Electrochemistry impedance spectroscopy and Mott-Schottky analysis were conducted to explore the reasons for the enhancement of the PEC performance. Pt NPs could promote the reduction of Co(Ⅳ)-oxo intermediate to Co(II) or Co(Ⅲ) which facilitated the charge transfer in the PEC performance. The result provides a promising guideline to design a simple and efficient photoelectrode for the PEC water-splitting system.

Humidity-Dependent Bacterial Cells Functional Morphometry Investigations Using Atomic Force Microscope

PubMed Central

Nikiyan, Hike; Vasilchenko, Alexey; Deryabin, Dmitry

2010-01-01

The effect of a relative humidity (RH) in a range of 93–65% on morphological and elastic properties of Bacillus cereus and Escherichia coli cells was evaluated using atomic force microscopy. It is shown that gradual dehumidification of bacteria environment has no significant effect on cell dimensional features and considerably decreases them only at 65% RH. The increasing of the bacteria cell wall roughness and elasticity occurs at the same time. Observed changes indicate that morphological properties of B. cereus are rather stable in wide range of relative humidity, whereas E. coli are more sensitive to drying, significantly increasing roughness and stiffness parameters at RH ≤ 84% RH. It is discussed the dependence of the response features on differences in cell wall structure of gram-positive and gram-negative bacterial cells. PMID:20652040

A dimensional comparison between embedded 3D-printed and silicon microchannels

NASA Astrophysics Data System (ADS)

O'Connor, J.; Punch, J.; Jeffers, N.; Stafford, J.

2014-07-01

The subject of this paper is the dimensional characterization of embedded microchannel arrays created using contemporary 3D-printing fabrication techniques. Conventional microchannel arrays, fabricated using deep reactive ion etching techniques (DRIE) and wet-etching (KOH), are used as a benchmark for comparison. Rectangular and trapezoidal cross-sectional shapes were investigated. The channel arrays were 3D-printed in vertical and horizontal directions, to examine the influence of print orientation on channel characteristics. The 3D-printed channels were benchmarked against Silicon channels in terms of the following dimensional characteristics: cross-sectional area (CSA), perimeter, and surface profiles. The 3D-printed microchannel arrays demonstrated variances in CSA of 6.6-20% with the vertical printing approach yielding greater dimensional conformity than the horizontal approach. The measured CSA and perimeter of the vertical channels were smaller than the nominal dimensions, while the horizontal channels were larger in both CSA and perimeter due to additional side-wall roughness present throughout the channel length. This side-wall roughness caused significant shape distortion. Surface profile measurements revealed that the base wall roughness was approximately the resolution of current 3D-printers. A spatial periodicity was found along the channel length which appeared at different frequencies for each channel array. This paper concludes that vertical 3D-printing is superior to the horizontal printing approach, in terms of both dimensional fidelity and shape conformity and can be applied in microfluidic device applications.

Effect of specific surface area of MWCNTS on surface roughness and delamination in drilling Epoxy/Glass Fabric Composite

NASA Astrophysics Data System (ADS)

Ponnuvel, S.; Ananth, M. Prem

2018-03-01

In this study the effect of specific surface area of the MWCNTs on the drilled hole qualities was investigated. Epoxy araldite LY556 with hardener HY951 and E-glass coarse plain weave fabric are used for the fabrication of reference material (specimen A). Multi-WalledCarbon Nanotubes (MWCNTs) with diameters <8 nm and 20–30 nm are used for the fabrication of study materials, namely specimen B and specimen C respectively. In specimen B the epoxy resin was filled with MWCNTs having a specific surface area >500 m2 g‑1. MWCNTs in specimen C had a specific surface area >110 m2 g‑1. Drilling experiments were conducted on all the three specimens. Two dimensional delamination factor and the surface roughness of the inner wall of the drilled holes were investigated using Grey Relational Analysis (GRA) and Analysis of variance (ANOVA). Two dimensional delamination factor showed better performance from specimen B and specimen C in comparison with specimen A suggesting improvement in the bonding between epoxy and the glass fiber in the presence of MWCNTs. Similar observations were made for surface roughness of the inner wall of the drilled holes at 1250 rpm. Whereas the presence of MWCNTs (Specimen B and specimen C) produced poor surface finish at 500 rpm in comparison with specimen A. Variations in the hole quality characteristics between specimen B and specimen C was marginal with better observations in specimen C.

Characterization of extraintestinal pathogenic Escherichia coli isolated from captive wild felids with bacteremia.

PubMed

Carvalho, Vania M; Osugui, Lika; Setzer, Ariela P; Lopez, Rodrigo P G; Pestana de Castro, Antonio F; Irino, Kinue; Catão-Dias, José L

2012-09-01

Diseases caused by extraintestinal pathogenic Escherichia coli (ExPEC) in wild felids are rarely reported. Although urinary tract infections are infrequently reported in domestic cats, such infections when present are commonly caused by ExPEC. The present work characterized ExPEC strains isolated from 2 adult felines, a snow leopard (Panthera uncia) and a black leopard (Panthera pardus melas), that died from secondary bacteremia associated with urinary tract infections. Isolates from both animals were classified into the B2 phylogenetic group and expressed virulence genotypes that allowed them to cause severe disease. In addition, strains from the black leopard showed multidrug resistance.

Brief report: increasing communication skills for an elementary-aged student with autism using the Picture Exchange Communication System.

PubMed

Kravits, Tamara R; Kamps, Debra M; Kemmerer, Katie; Potucek, Jessica

2002-06-01

The purpose of this study was to examine the effects of the Picture Exchange Communication System (PECS) on the spontaneous communication skills of a 6-year-old girl with autism across her home and school environments. The effects of the PECS were also examined for social interaction. Results indicated increases in spontaneous language (i.e., requests and comments) including use of the icons and verbalizations across those settings in which PECS was implemented. Intelligible verbalizations increased in two of three settings, and changes in peer social interaction were noted in one of the two school settings.

Spondylodiscitis in a healthy 12-year-old girl with Extraintestinal pathogenic Escherichia coli (ExPEC) bacteraemia.

PubMed

Gaschignard, J; Geslain, G; Mallet, C; Lorrot, M; Blot, N; Alison, M; Bonacorsi, S

2017-05-31

Escherichia coli (E. coli) is rarely implicated in bone or joint infections in children. We discuss the case of a healthy 12-year-old girl with an E. coli bacteraemia and a T11-T12 spondylodiscitis revealed by magnetic resonance imaging. The strain harboured serogroup O1:K1 and virulence factors common to highly virulent extra intestinal pathogenic E. coli (ExPEC). Immunological work-up was normal. The identification of E. coli in a spondylodiscitis should lead to the search for immunosuppression of the host and virulence factors of the strain, particularly those of ExPEC.

Effect of gangliosides in the autoimmune response induced by liposome-associated antigens.

PubMed

Correa, S G; Rivero, V E; Yranzo-Volonté, N; Romero-Piffiguer, M; Ferro, M E; Riera, C M

1993-01-01

A model of autoimmunity to rat male accessory glands (RAG) was recently developed by intraperitoneal administration of three doses of native RAG associated with liposomes. In this work we analysed the effects of gangliosides in the cellular response to RAG when they were intraperitoneally administrated prior to the second dose of liposome-associated RAG. Results show that the ganglioside treatment could modify an established DTH response. Also, gangliosides markedly reduced the number of Ia antigen-positive peritoneal exudated cells (PEC). However, they modified neither the processing of liposomes through PEC nor their viability. Moreover, we obtained cellular response by transferring PEC from immunized donors into naive receptors.

FROM CONCEPT TO EQUIVALENCY: THE 503 REGULATIONS AND THE PATHOGEN EQUIVALENCY COMMITTEE (PAPER)

EPA Science Inventory

Since its creation in 1985, the Pathogen Equivalency Committee (PEC) has been reviewing innovative and alternative sludge disinfection technologies with regards to their abilities to protect human health and the environment. The PEC is charged to make recommendations on whether t...

Using graphene-based plasmonic nanocomposites to quench energy from quantum dots for signal-on photoelectrochemical aptasensing.

PubMed

Zeng, Xianxiang; Ma, Shishi; Bao, Jianchun; Tu, Wenwen; Dai, Zhihui

2013-12-17

On the basis of the absorption and emission spectra overlap, an enhanced resonance energy transfer caused by excition-plasmon resonance between reduced graphene oxide (RGO)-Au nanoparticles (AuNPs) and CdTe quantum dots (QDs) was obtained. With the synergy of AuNPs and RGO as a planelike energy acceptor, it resulted in the enhancement of energy transfer between excited CdTe QDs and RGO-AuNPs nanocomposites. Upon the novel sandwichlike structure formed via DNA hybridization, the exciton produced in CdTe QDs was annihilated. A damped photocurrent was obtained, which was acted as the background signal for the development of a universal photoelectrochemical (PEC) platform. With the use of carcinoembryonic antigen (CEA) as a model which bonded to its specific aptamer and destroyed the sandwichlike structure, the energy transfer efficiency was lowered, leading to PEC response augment. Thus a signal-on PEC aptasensor was constructed. Under 470 nm irradiation at -0.05 V, the PEC aptasensor for CEA determination exhibited a linear range from 0.001 to 2.0 ng mL(-1) with a detection limit of 0.47 pg mL(-1) at a signal-to-noise ratio of 3 and was satisfactory for clinical sample detection. Since different aptamers can specifically bind to different target molecules, the designed strategy has an expansive application for the construction of versatile PEC platforms.

Coordinated Hospital-Home Fecal Microbiota Transplantation via Percutaneous Endoscopic Cecostomy for Recurrent Steroid-Dependent Ulcerative Colitis.

PubMed

Ni, Xiaodong; Fan, Shengxian; Zhang, Yongliang; Wang, Zhiming; Ding, Lan; Li, Yousheng; Li, Jieshou

2016-11-15

Since its introduction as an alternative intestinal microbiota alteration approach, fecal microbiota transplantation (FMT) has been increasingly used as a treatment of choice for patients with ulcerative colitis (UC), but no reports exist regarding FMT via percutaneous endoscopic cecostomy (PEC). This report describes the case of a 24-year-old man with a 7-year history of recurrent, steroid-dependent UC. He received FMT via PEC once per day for 1 month in the hospital. After the remission of gastrointestinal symptoms, he was discharged from the hospital and continued FMT via PEC twice per week for 3 months at home. The frequency of stools decreased, and the characteristics of stools improved soon thereafter. Enteral nutrition was regained after 1 week, and an oral diet was begun 1 month later. Two months after the FMT end point, the patient resumed a normal diet, with formed soft stools once per day. The follow-up colonoscopy showed normal mucus membranes; then, the PEC set was removed. On the subsequent 12 months follow-up, the patient resumed orthobiosis without any gastrointestinal discomfort and returned to work. This case emphasizes that FMT via PEC can not only induce remission but also shorten the duration of hospitalization and reduce the medical costs; therefore, this approach should be considered an alternative option for patients with UC.

Are exposure predictions, used for the prioritization of pharmaceuticals in the environment, fit for purpose?

USGS Publications Warehouse

Burns, Emily E.; Thomas-Oates, Jane; Kolpin, Dana W.; Furlong, Edward T.; Boxall, Alistair B.A.

2017-01-01

Prioritization methodologies are often used for identifying those pharmaceuticals that pose the greatest risk to the natural environment and to focus laboratory testing or environmental monitoring toward pharmaceuticals of greatest concern. Risk-based prioritization approaches, employing models to derive exposure concentrations, are commonly used, but the reliability of these models is unclear. The present study evaluated the accuracy of exposure models commonly used for pharmaceutical prioritization. Targeted monitoring was conducted for 95 pharmaceuticals in the Rivers Foss and Ouse in the City of York (UK). Predicted environmental concentration (PEC) ranges were estimated based on localized prescription, hydrological data, reported metabolism, and wastewater treatment plant (WWTP) removal rates, and were compared with measured environmental concentrations (MECs). For the River Foss, PECs, obtained using highest metabolism and lowest WWTP removal, were similar to MECs. In contrast, this trend was not observed for the River Ouse, possibly because of pharmaceutical inputs unaccounted for by our modeling. Pharmaceuticals were ranked by risk based on either MECs or PECs. With 2 exceptions (dextromethorphan and diphenhydramine), risk ranking based on both MECs and PECs produced similar results in the River Foss. Overall, these findings indicate that PECs may well be appropriate for prioritization of pharmaceuticals in the environment when robust and local data on the system of interest are available and reflective of most source inputs. 

Testing of NASA LaRC Materials under MISSE 6 and MISSE 7 Missions

NASA Technical Reports Server (NTRS)

Prasad, Narasimha S.

2009-01-01

The objective of the Materials International Space Station Experiment (MISSE) is to study the performance of novel materials when subjected to the synergistic effects of the harsh space environment for several months. MISSE missions provide an opportunity for developing space qualifiable materials. Two lasers and a few optical components from NASA Langley Research Center (LaRC) were included in the MISSE 6 mission for long term exposure. MISSE 6 items were characterized and packed inside a ruggedized Passive Experiment Container (PEC) that resembles a suitcase. The PEC was tested for survivability due to launch conditions. MISSE 6 was transported to the international Space Station (ISS) via STS 123 on March 11. 2008. The astronauts successfully attached the PEC to external handrails of the ISS and opened the PEC for long term exposure to the space environment. The current plan is to bring the MISSE 6 PEC back to the Earth via STS 128 mission scheduled for launch in August 2009. Currently, preparations for launching the MISSE 7 mission are progressing. Laser and lidar components assembled on a flight-worthy platform are included from NASA LaRC. MISSE 7 launch is scheduled to be launched on STS 129 mission. This paper will briefly review recent efforts on MISSE 6 and MISSE 7 missions at NASA Langley Research Center (LaRC).

Highly selective transformation of ammonia nitrogen to N2 based on a novel solar-driven photoelectrocatalytic-chlorine radical reactions system.

PubMed

Ji, Youzhi; Bai, Jing; Li, Jinhua; Luo, Tao; Qiao, Li; Zeng, Qingyi; Zhou, Baoxue

2017-11-15

A highly selective method for transforming ammonia nitrogen to N 2 was proposed, based on a novel solar-driven photoelectrocatalytic-chlorine radical reactions (PEC-chlorine) system. The PEC-chlorine system was facilitated by a visible light response WO 3 nanoplate array (NPA) electrode in an ammonia solution containing chloride ions (Cl - ). Under illumination, photoholes from WO 3 promote the oxidation of Cl - to chlorine radical (Cl). This radical can selectively transform ammonia nitrogen to N 2 (79.9%) and NO 3 - (19.2%), similar to the breakpoint chlorination reaction. The ammonia nitrogen removal efficiency increased from 10.6% (PEC without Cl - ) to 99.9% with the PEC-chlorine system within 90 min operation, which can be attributed to the cyclic reactions between Cl - /Cl and the reaction intermediates (NH 2 , NHCl, etc.) that expand the degradation reactions from the surface of the electrodes to the whole solution system. Moreover, Cl is the main radical species contributing to the transformation of ammonia nitrogen to N 2 , which is confirmed by the tBuOH capture experiment. Compared to conventional breakpoint chlorination, the PEC-chlorine system is a more economical and efficient means for ammonia nitrogen degradation because of the fast removal rate, no additional chlorine cost, and its use of clean energy (since it is solar-driven). Copyright © 2017 Elsevier Ltd. All rights reserved.

Improved Stability and Performance of Visible Photoelectrochemical Water Splitting on Solution-Processed Organic Semiconductor Thin Films by Ultrathin Metal Oxide Passivation

DOE PAGES

Wang, Lei; Yan, Danhua; Shaffer, David W.; ...

2017-12-27

Solution-processable organic semiconductors have potentials as visible photoelectrochemical (PEC) water splitting photoelectrodes due to their tunable small band gap and electronic energy levels, but they are typically limited by poor stability and photocatalytic activity. In this study, we demonstrate the direct visible PEC water oxidation on solution-processed organic semiconductor thin films with improved stability and performance by ultrathin metal oxide passivation layers. N-type fullerene-derivative thin films passivated by sub-2 nm ZnO via atomic layer deposition enabled the visible PEC water oxidation at wavelengths longer than 600 nm in harsh alkaline electrolyte environments with up to 30 μA/cm 2 photocurrents atmore » the thermodynamic water-oxidation equilibrium potential and the photoanode half-lifetime extended to ~1000 s. The systematic investigation reveals the enhanced water oxidation catalytic activity afforded by ZnO passivation and the charge tunneling governing the hole transfer through passivation layers. Further enhanced PEC performances were realized by improving the bottom ohmic contact to the organic semiconductor, achieving ~60 μA/cm 2 water oxidation photocurrent at the equilibrium potential, the highest values reported for organic semiconductor thin films to our knowledge. The improved stability and performance of passivated organic photoelectrodes and discovered design rationales provide useful guidelines for realizing the stable visible solar PEC water splitting based on organic semiconductor thin films.« less

Genomic Microbial Epidemiology Is Needed to Comprehend the Global Problem of Antibiotic Resistance and to Improve Pathogen Diagnosis.

PubMed

Wyrsch, Ethan R; Roy Chowdhury, Piklu; Chapman, Toni A; Charles, Ian G; Hammond, Jeffrey M; Djordjevic, Steven P

2016-01-01

Contamination of waste effluent from hospitals and intensive food animal production with antimicrobial residues is an immense global problem. Antimicrobial residues exert selection pressures that influence the acquisition of antimicrobial resistance and virulence genes in diverse microbial populations. Despite these concerns there is only a limited understanding of how antimicrobial residues contribute to the global problem of antimicrobial resistance. Furthermore, rapid detection of emerging bacterial pathogens and strains with resistance to more than one antibiotic class remains a challenge. A comprehensive, sequence-based genomic epidemiological surveillance model that captures essential microbial metadata is needed, both to improve surveillance for antimicrobial resistance and to monitor pathogen evolution. Escherichia coli is an important pathogen causing both intestinal [intestinal pathogenic E. coli (IPEC)] and extraintestinal [extraintestinal pathogenic E. coli (ExPEC)] disease in humans and food animals. ExPEC are the most frequently isolated Gram negative pathogen affecting human health, linked to food production practices and are often resistant to multiple antibiotics. Cattle are a known reservoir of IPEC but they are not recognized as a source of ExPEC that impact human or animal health. In contrast, poultry are a recognized source of multiple antibiotic resistant ExPEC, while swine have received comparatively less attention in this regard. Here, we review what is known about ExPEC in swine and how pig production contributes to the problem of antibiotic resistance.

Improved Stability and Performance of Visible Photoelectrochemical Water Splitting on Solution-Processed Organic Semiconductor Thin Films by Ultrathin Metal Oxide Passivation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Lei; Yan, Danhua; Shaffer, David W.

Solution-processable organic semiconductors have potentials as visible photoelectrochemical (PEC) water splitting photoelectrodes due to their tunable small band gap and electronic energy levels, but they are typically limited by poor stability and photocatalytic activity. In this study, we demonstrate the direct visible PEC water oxidation on solution-processed organic semiconductor thin films with improved stability and performance by ultrathin metal oxide passivation layers. N-type fullerene-derivative thin films passivated by sub-2 nm ZnO via atomic layer deposition enabled the visible PEC water oxidation at wavelengths longer than 600 nm in harsh alkaline electrolyte environments with up to 30 μA/cm 2 photocurrents atmore » the thermodynamic water-oxidation equilibrium potential and the photoanode half-lifetime extended to ~1000 s. The systematic investigation reveals the enhanced water oxidation catalytic activity afforded by ZnO passivation and the charge tunneling governing the hole transfer through passivation layers. Further enhanced PEC performances were realized by improving the bottom ohmic contact to the organic semiconductor, achieving ~60 μA/cm 2 water oxidation photocurrent at the equilibrium potential, the highest values reported for organic semiconductor thin films to our knowledge. The improved stability and performance of passivated organic photoelectrodes and discovered design rationales provide useful guidelines for realizing the stable visible solar PEC water splitting based on organic semiconductor thin films.« less

Crater Rim Layers, Rubble, and Gullies

NASA Image and Video Library

2017-08-07

This observation from NASA's Mars Reconnaissance Orbiter shows a close view of the rim and upper wall of an impact crater on the Martian surface. The layers in enhanced color are exposed subsurface strata that are relatively resistant to erosion. Boulder-like rubble beyond the crater rim is scattered down the wall of the crater (down-slope is toward the lower left of the image). Another feature of interest to Mars scientists is a large gully roughly 100 meters across. These gullies may have formed when water from melted ice on the crater walls, or from groundwater within the walls, assisted in transporting eroding material downslope. https://photojournal.jpl.nasa.gov/catalog/PIA21870

Macrophages Are the Major Reservoir of Latent Murine Gammaherpesvirus 68 in Peritoneal Cells

PubMed Central

Weck, Karen E.; Kim, Susanne S.; Virgin, Herbert W.; Speck, Samuel H.

1999-01-01

B cells have previously been identified as the major hematopoietic cell type harboring latent gammaherpesvirus 68 (γHV68) (N. P. Sunil-Chandra, S. Efstathiou, and A. A. Nash, J. Gen. Virol. 73:3275–3279, 1992). However, we have shown that γHV68 efficiently establishes latency in B-cell-deficient mice (K. E. Weck, M. L. Barkon, L. I. Yoo, S. H. Speck, and H. W. Virgin, J. Virol. 70:6775–6780, 1996), demonstrating that B cells are not required for γHV68 latency. To understand this dichotomy, we determined whether hematopoietic cell types, in addition to B cells, carry latent γHV68. We observed a high frequency of cells that reactivate latent γHV68 in peritoneal exudate cells (PECs) derived from both B-cell-deficient and normal C57BL/6 mice. PECs were composed primarily of macrophages in B-cell-deficient mice and of macrophages plus B cells in normal C57BL/6 mice. To determine which cells in PECs from C57BL/6 mice carry latent γHV68, we developed a limiting-dilution PCR assay to quantitate the frequency of cells carrying the γHV68 genome in fluorescence-activated cell sorter-purified cell populations. We also quantitated the contribution of individual cell populations to the total frequency of cells carrying latent γHV68. At early times after infection, the frequency of PECs that reactivated γHV68 correlated very closely with the frequency of PECs carrying the γHV68 genome, validating measurement of the frequency of viral-genome-positive cells as a measure of latency in this cell population. F4/80-positive macrophage-enriched, lymphocyte-depleted PECs harbored most of the γHV68 genome and efficiently reactivated γHV68, while CD19-positive, B-cell-enriched PECs harbored about a 10-fold lower frequency of γHV68 genome-positive cells. CD4-positive, T-cell-enriched PECs contained only a very low frequency of γHV68 genome-positive cells, consistent with previous analyses indicating that T cells are not a reservoir for γHV68 latency (N. P. Sunil-Chandra, S. Efstathiou, and A. A. Nash, J. Gen. Virol. 73:3275–3279, 1992). Since macrophages are bone marrow derived, we determined whether elicitation of a large inflammatory response in the peritoneum would recruit additional latent cells into the peritoneum. Thioglycolate inoculation increased the total number of PECs by about 20-fold but did not affect the frequency of cells that reactivate γHV68, consistent with a bone marrow reservoir for latent γHV68. These experiments demonstrate γHV68 latency in two different hematopoietic cell types, F4/80-positive macrophages and CD19-positive B cells, and argue for a bone marrow reservoir for latent γHV68. PMID:10074181

3D WO3 /BiVO4 /Cobalt Phosphate Composites Inverse Opal Photoanode for Efficient Photoelectrochemical Water Splitting.

PubMed

Zhang, Haifeng; Zhou, Weiwei; Yang, Yaping; Cheng, Chuanwei

2017-04-01

A novel 3D WO 3 /BiVO 4 /cobalt phosphate composite inverse opal is designed for photoeletrochemical (PEC) water splitting, yielding a significantly improved PEC performance. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

UPDATE ON PEC ACTIVITIES INCLUDING NEW EVALUATION CRITERIA, THE APPLICATION COMPLETENESS CHECKLIST, AND STATUS OF THE WEBSITE DEVELOPMENT

EPA Science Inventory

US EPA's Pathogen Equivalency Committee (PEC) has updated the evaluation criteria it uses to make recommendations of equivalency (to processes acceptable under 40CFR503) on innovative or alternative sludge pathogen reduction processes. These criteria will be presented along with ...

An Evaluation of Strategies for Training Staff to Implement the Picture Exchange Communication System

ERIC Educational Resources Information Center

Barnes, Clarissa S.; Dunning, Johnna L.; Rehfeldt, Ruth Anne

2011-01-01

The picture exchange communication system (PECS) is a functional communication system frequently used with individuals diagnosed with autism spectrum disorders who experience severe language delays (Frost & Bondy, 2002). Few empirical investigations have evaluated strategies for training direct care staff how to effectively implement PECS with…

The Unusual Suspects: Myths and Misconceptions Associated with PECS

ERIC Educational Resources Information Center

Bondy, Andy

2012-01-01

The Picture Exchange Communication System (PECS) is an alternative/augmentative communication protocol designed to help children and adults with autism and related disabilities to engage in functional communication. The protocol was developed over a number of years and was based on Skinner's analysis of verbal behavior. Publications about the…

The Effectiveness of the "Picture Exchange Communication System" with Nonspeaking Adults

ERIC Educational Resources Information Center

Stoner, Julia B.; Beck, Ann R.; Bock, Stacey Jones; Hickey, Katherine; Kosuwan, Kullaya; Thompson, James R.

2006-01-01

"Picture Exchange Communication System" (PECS) training was implemented with 5 nonspeaking adults with mental retardation who were not currently using any type of functional communication system. A modified ABAB, single-subject design was used to assess the effectiveness of PECS in enhancing the functional communication skills of these…

Shooting and bouncing rays - Calculating the RCS of an arbitrarily shaped cavity

NASA Technical Reports Server (NTRS)

Ling, Hao; Chou, Ri-Chee; Lee, Shung-Wu

1989-01-01

A ray-shooting approach is presented for calculating the interior radar cross section (RCS) from a partially open cavity. In the problem considered, a dense grid of rays is launched into the cavity through the opening. The rays bounce from the cavity walls based on the laws of geometrical optics and eventually exit the cavity via the aperture. The ray-bouncing method is based on tracking a large number of rays launched into the cavity through the opening and determining the geometrical optics field associated with each ray by taking into consideration (1) the geometrical divergence factor, (2) polarization, and (3) material loading of the cavity walls. A physical optics scheme is then applied to compute the backscattered field from the exit rays. This method is so simple in concept that there is virtually no restriction on the shape or material loading of the cavity. Numerical results obtained by this method are compared with those for the modal analysis for a circular cylinder terminated by a PEC plate. RCS results for an S-bend circular cylinder generated on the Cray X-MP supercomputer show significant RCS reduction. Some of the limitations and possible extensions of this technique are discussed.

A molecular dynamics study of freezing in a confined geometry

NASA Technical Reports Server (NTRS)

Ma, Wen-Jong; Banavar, Jayanth R.; Koplik, Joel

1992-01-01

The dynamics of freezing of a Lennard-Jones liquid in narrow channels bounded by molecular walls is studied by computer simulation. The time development of ordering is quantified and a novel freezing mechanism is observed. The liquid forms layers and subsequent in-plane ordering within a layer is accompanied by a sharpening of the layer in the transverse direction. The effects of channel size, the methods of quench, the liquid-wall interaction and the roughness of walls on the freezing mechanism are elucidated. Comparison with recent experiments on freezing in confined geometries is presented.

Inner and outer layer turbulence over a superhydrophobic surface with low roughness level at low Reynolds number

NASA Astrophysics Data System (ADS)

Abu Rowin, W.; Hou, J.; Ghaemi, S.

2017-09-01

The inner and outer layers of a turbulent channel flow over a superhydrophobic surface (SHS) are characterized using simultaneous long-range microscopic particle tracking velocimetry (micro-PTV) and particle image velocimetry, respectively. The channel flow is operated at a low Reynolds number of ReH = 4400 (based on full channel height and 0.174 m/s bulk velocity), equivalent to Reτ = 140 (based on half channel height and friction velocity). The SHS is produced by spray coating, and the root-mean-square of wall roughness normalized by wall-unit is k+rms = 0.11. The micro-PTV shows 0.023 m/s slip velocity over the SHS (about 13% of the bulk velocity), which corresponds to a slip-length of ˜200 μm. A drag reduction of ˜19% based on the slope of the linear viscous sublayer and 22% based on an analytical expression of Rastegari and Akhavan [J. Fluid Mech. 773, R4 (2015)] realized. The reduced Reτ over the SHS based on the corresponding friction velocity is ˜125, which is in the lower limit of a turbulence regime. The results show the increase of streamwise Reynolds stresses for the SHS in the linear viscous sublayer due to the slip boundary condition. The peak does not change in magnitude while it is displaced closer to the wall in physical distance. The wall-normal Reynolds stress over the SHS and smooth surface is observed to overlap near the wall at y+ < 10, while for the SHS is smaller further away from the wall in physical dimensions. At y+ = 30, is 30% smaller for the SHS. A small increase of Reynolds shear stress for the SHS is observed at y+ < 10, while about 30% reduction is observed at y+ = 30. The observed variation of Reynolds stresses is associated with the relatively small roughness of the surface. If Reynolds stresses are normalized based on the corresponding friction velocity, the non-dimensional stresses show a large increase of and a small increase of over the SHS at y+ < 20. Farther away from the wall at y+ > 20, the scaling of Reynolds stresses based on the corresponding uτ results in their overlap for the smooth and SHSs. The drag reduction is mainly associated with the reduction of viscous wall-shear stress, while the variation in Reynolds shear stress at the wall is negligible. The quadrant analysis of turbulent fluctuations shows attenuation of stronger sweep motions at y+ < 15, while ejections are attenuated in the buffer layer at y+ = 20 until 30.

Effect of seabed roughness on tidal current turbines

NASA Astrophysics Data System (ADS)

Gupta, Vikrant; Wan, Minping

2017-11-01

Tidal current turbines are shown to have potential to generate clean energy for a negligible environmental impact. These devices, however, operate in high to moderate current regions where the flow is highly turbulent. It has been shown in flume tank experiments at IFREMER in Boulogne-Sur-Mer (France) and NAFL in the University of Minnesota (US) that the level of turbulence and boundary layer profile affect a turbine's power output and wake characteristics. A major factor that determines these marine flow characteristics is the seabed roughness. Experiments, however, cannot simulate the high Reynolds number conditions of real marine flows. For that, we rely on numerical simulations. High accuracy numerical methods, such as DNS, of wall-bounded flows are very expensive, where the number of grid-points needed to resolve the flow varies as (Re) 9 / 4 (where Re is the flow Reynolds number). While numerically affordable RANS methods compromise on accuracy. Wall-modelled LES methods, which provide both accuracy and affordability, have been improved tremendously in the recent years. We discuss the application of such numerical methods for studying the effect of seabed roughness on marine flow features and their impact on turbine power output and wake characteristics. NSFC, Project Number 11672123.

Influences of roughness on the inertial mechanism of turbulent boundary-layer scale separation

NASA Astrophysics Data System (ADS)

Ebner, Rachel

Measurements and scaling analyses are conducted to clarify the combined effects of roughness and Reynolds number on momentum transport in the rough-wall zero pressure gradient turbulent boundary layer. A series of multi-sensor hot-wire experiments are presented that cover nearly a decade in Reynolds number and nearly three decades in the inner-normalized sand grain roughness. This dissertation utilizes the difference between two velocity-vorticity correlations to represent the turbulent inertia term in the statement of the mean dynamics for turbulent boundary layer flow. Analyses focus on the first term on the right hand side of the equation, because it is physically affiliated with change-of-scale effects (Tennekes and Lumley, 1972). Similarity analysis, streamwise correlations, and spectral methods are performed to elucidate the scaling behaviors of the turbulent inertia term relative to the mean dynamics. The present results reveal complex behaviors in the long-time statistics of the velocity-vorticity correlation that exhibit both Reynolds number and roughness dependencies. The results broadly support the combined roughness-Reynolds number description provided by Mehdi et al, (2013).

PULSED EDDY CURRENT THICKNESS MEASUREMENT OF SELECTIVE PHASE CORROSION ON NICKEL ALUMINUM BRONZE VALVES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krause, T. W.; Harlley, D.; Babbar, V. K.

Nickel Aluminum Bronze (NAB) is a material with marine environment applications that under certain conditions can undergo selective phase corrosion (SPC). SPC involves the removal of minority elements while leaving behind a copper matrix. Pulsed eddy current (PEC) was evaluated for determination of SPC thickness on a NAB valve section with access from the surface corroded side. A primarily linear response of PEC amplitude, up to the maximum available SPC thickness of 4 mm was observed. The combination of reduced conductivity and permeability in the SPC phase relative to the base NAB was used to explain the observed sensitivity ofmore » PEC to SPC thickness variations.« less

Influence of pH on the quantum-size-controlled photoelectrochemical etching of epitaxial InGaN quantum dots

DOE PAGES

Xiao, Xiaoyin; Lu, Ping; Fischer, Arthur J.; ...

2015-11-18

Illumination by a narrow-band laser has been shown to enable photoelectrochemical (PEC) etching of InGaN thin films into quantum dots with sizes controlled by the laser wavelength. Here, we investigate and elucidate the influence of solution pH on such quantum-size-controlled PEC etch process. We find that although a pH above 5 is often used for PEC etching of GaN-based materials, oxides (In 2O 3 and/or Ga 2O 3) form which interfere with quantum dot formation. Furthermore, at pH below 3, however, oxide-free QDs with self-terminated sizes can be successfully realized.

9 CFR 590.550 - Washing and sanitizing room or area facilities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and walls shall have a surface of tile, enamel paint, or other water-resistant material. (c) Floors shall be adequately sloped for proper drainage, be free from cracks or rough surfaces where water and...

Pesticide Environmental Fate Research for the 21st Century: Building Bridges Between Laboratory and Field Studies at Varying Scales

USDA-ARS?s Scientific Manuscript database

Accurate determination of predicted environmental concentrations (PECs) is a continuing and often elusive goal of pesticide risk assessment. PECs are typically derived using simulation models that depend on laboratory generated data for key input parameters (t1/2, Koc, etc.). Model flexibility in ...

Pesticide Environmental Fate Research for the 21st Century: Building Bridges Between Laboratory and Field Studies at Varying Scales

USDA-ARS?s Scientific Manuscript database

Accurate determination of predicted environmental concentrations (PECs) is a continuing and often elusive goal of pesticide risk assessment. PECs are typically derived using simulation models that depend on laboratory generated data for key input parameters (t1/2, Koc, etc.). Model flexibility in ev...

Todd G. Deutsch | NREL

Science.gov Websites

page. Research Interests Solar energy conversion to hydrogen fuel via PEC water splitting III-V ://orcid.org/0000-0001-6577-1226 Dr. Deutsch has been studying photoelectrochemical (PEC) water splitting since semiconductor water-splitting systems under the joint guidance of Dr. Turner and Prof. Carl A. Koval in the

Nanophotonic Devices - Spontaneous Emission Faster than Stimulated Emission

DTIC Science & Technology

2014-11-04

2010 Granada Spain PECS IX "The Two Conflicting Narratives of Metal-Optics" Aug. 17, 2010 Seoul Korea IEEE Nano Korea Symposium "The Two...Two Conflicting Narratives of Metal-Optics" Sept. 28, 2010 Granada Spain PECS IX "The Two Conflicting Narratives of Metal-Optics" Aug. 17, 2010

A Communication-Based Intervention for Nonverbal Children with Autism: What Changes? Who Benefits?

ERIC Educational Resources Information Center

Gordon, Kate; Pasco, Greg; McElduff, Fiona; Wade, Angie; Howlin, Pat; Charman, Tony

2011-01-01

Objective: This article examines the form and function of spontaneous communication and outcome predictors in nonverbal children with autism following classroom-based intervention (Picture Exchange Communication System [PECS] training). Method: 84 children from 15 schools participated in a randomized controlled trial (RCT) of PECS (P. Howlin, R.…

Quantitative Synthesis and Component Analysis of Single-Participant Studies on the Picture Exchange Communication System

ERIC Educational Resources Information Center

Tincani, Matt; Devis, Kathryn

2011-01-01

The "Picture Exchange Communication System" (PECS) has emerged as the augmentative communication intervention of choice for individuals with autism spectrum disorder (ASD), with a supporting body of single-participant studies. This report describes a meta-analysis of 16 single-participant studies on PECS with percentage of nonoverlapping data…

Using the Picture Exchange Communication System with Students with Visual Impairment

ERIC Educational Resources Information Center

Ivy, Sarah E.; Hatton, Deborah D.; Hooper, Jonathan D.

2014-01-01

Students with visual impairment (VI) were taught to request using the Picture Exchange Communication System (PECS) and tangible symbols. Participants were four males with additional disabilities, 5 to 11 years old, who had little to no functional vision. A functional relation between PECS Phase 1 and requesting was established using a multiple…

Effects of Implementing the Picture Exchange Communication System (PECS) with Adults with Developmental Disabilities and Severe Communication Deficits

ERIC Educational Resources Information Center

Conklin, Carl G.; Mayer, G. Roy

2011-01-01

The purpose of this study is to evaluate the effects of "Picture Exchange Communication System" (PECS) training, using a multiple baseline design on the independent initiations of three adults with developmental disabilities and severe communication deficits. All participants increased their independent initiations, although at different…

APPLYING TO THE PEC: A CASE HISTORY - A WALK THROUGH THE PROCEDURE FOR APPLYING FOR EQUIVALENCY USING A RECENT CANDIDATE AS A TRUE EXAMPLE.

EPA Science Inventory

The USEPA's Pathogen Equivalency Committee (PEC) is entrusted by its Office of Water to critically evaluate innovative and alternative sludge disinfection processes and make recommendations about their Process to Significantly Reduce Pathogens (PSRP) or Process to Further Reduce ...

Six International Conferences of PEC (The Peace Education Commission). Peace Education Miniprints No. 87.

ERIC Educational Resources Information Center

Bjerstedt, Ake

This pamphlet offers an overview of five larger reports in order to facilitate the process of locating contributions originating from five peace conferences between 1990-1994. The Peace Education Commission (PEC) arranged five conferences in Groningen (The Netherlands), Firenze (Italy), Kyoto (Japan), Budapest (Hungary) and Valletta (Malta). A…

LETTER TO THE EDITOR: Iteratively-coupled propagating exterior complex scaling method for electron hydrogen collisions

NASA Astrophysics Data System (ADS)

Bartlett, Philip L.; Stelbovics, Andris T.; Bray, Igor

2004-02-01

A newly-derived iterative coupling procedure for the propagating exterior complex scaling (PECS) method is used to efficiently calculate the electron-impact wavefunctions for atomic hydrogen. An overview of this method is given along with methods for extracting scattering cross sections. Differential scattering cross sections at 30 eV are presented for the electron-impact excitation to the n = 1, 2, 3 and 4 final states, for both PECS and convergent close coupling (CCC), which are in excellent agreement with each other and with experiment. PECS results are presented at 27.2 eV and 30 eV for symmetric and asymmetric energy-sharing triple differential cross sections, which are in excellent agreement with CCC and exterior complex scaling calculations, and with experimental data. At these intermediate energies, the efficiency of the PECS method with iterative coupling has allowed highly accurate partial-wave solutions of the full Schrödinger equation, for L les 50 and a large number of coupled angular momentum states, to be obtained with minimal computing resources.

Micromachined microbial and photosynthetic fuel cells

NASA Astrophysics Data System (ADS)

Chiao, Mu; Lam, Kien B.; Lin, Liwei

2006-12-01

This paper presents two types of fuel cells: a miniature microbial fuel cell (µMFC) and a miniature photosynthetic electrochemical cell (µPEC). A bulk micromachining process is used to fabricate the fuel cells, and the prototype has an active proton exchange membrane area of 1 cm2. Two different micro-organisms are used as biocatalysts in the anode: (1) Saccharomyces cerevisiae (baker's yeast) is used to catalyze glucose and (2) Phylum Cyanophyta (blue-green algae) is used to produce electrons by a photosynthetic reaction under light. In the dark, the µPEC continues to generate power using the glucose produced under light. In the cathode, potassium ferricyanide is used to accept electrons and electric power is produced by the overall redox reactions. The bio-electrical responses of µMFCs and µPECs are characterized with the open-circuit potential measured at an average value of 300-500 mV. Under a 10 ohm load, the power density is measured as 2.3 nW cm-2 and 0.04 nW cm-2 for µMFCs and µPECs, respectively.

Thiolated citrus low-methoxyl pectin: Synthesis, characterization and rheological and oxidation-responsive gelling properties.

PubMed

Chen, Jinfeng; Ye, Fayin; Zhou, Yun; Zhao, Guohua

2018-02-01

In the present study, citrus low-methoxyl pectin was modified by conjugating cysteine via amide bonds, and the resultant polymer (CYS-PEC) was characterized. CYS-PEC conjugates with thiol contents varying from 77.8μmol/g to 296μmol/g were synthesized, and the successful conjugation was evidenced by elemental, and FT-IR analyses. The sulfur in CYS-PEC is predominately in the thiol form, with a minor fraction forming disulfide bonds (∼15%), which occur when thiol/disulfide interchange interrupts the intended thiolation. Both native and modified pectin dispersions exhibited strong pseudoplastic properties, and the frequency sweeps revealed them to be dispersions containing microgel particles. Dynamic viscoelastic analysis was used to determine the oxidation-response gelling capacities of polymer dispersions containing H 2 O 2 , especially those that are highly thiolated and have cross-linked gel properties. For oxidation-induced CYS-PEC gels, their gelation time, hardness, viscosity and elastic moduli and swelling-disintegration ratio are dependent on the thiol group content, H 2 O 2 concentration and polymer concentration. Copyright © 2017 Elsevier Ltd. All rights reserved.

Photoelectrochemical enhancement of ZnO/BiVO4/ZnFe2O4/rare earth oxide hetero-nanostructures

NASA Astrophysics Data System (ADS)

She, Xuefeng; Zhang, Zhuo; Baek, Minki; Yong, Kijung

2018-01-01

Over the decades, researchers have made great efforts to turn the world into a cleaner place through efficient recycling of industrial waste and developing of green energy. Here we demonstrate a prototype heterostructure photoelectrochemical (PEC) cell fabricated using recycled industrial waste. ZnFe2O4 (ZFO) nanorod (NR) clusters were synthesized on the BiVO4@ZnO hetero-nanostructures using recycled rare earth oxide (REO) slags as Fe source. The NR-based PEC cell exhibited a significantly enhanced photon to hydrogen conversion efficiency over the entire UV and visible spectrum. Further study demonstrates that the photo-carrier separation and migration processes can be facilitated by the cascade band alignment of the heterostructure and the clustered nanostructure network. In addition, the life-time of the photo-carriers can be enhanced by the REO passivation layer, leading to a further increased PEC performance. Our results present a novel approach for high efficiency PEC cells, and offer great promises to the efficient recycling of industrial waste for clean renewable energy applications.

Pulsed eddy current differential probe to detect the defects in a stainless steel pipe

NASA Astrophysics Data System (ADS)

Angani, C. S.; Park, D. G.; Kim, C. G.; Leela, P.; Kishore, M.; Cheong, Y. M.

2011-04-01

Pulsed eddy current (PEC) is an electromagnetic nondestructive technique widely used to detect and quantify the flaws in conducting materials. In the present study a differential Hall-sensor probe which is used in the PEC system has been fabricated for the detection of defects in stainless steel pipelines. The differential probe has an exciting coil with two Hall-sensors. A stainless steel test sample with electrical discharge machining (EDM) notches under different depths of 1-5 mm was made and the sample was laminated by plastic insulation having uniform thickness to simulate the pipelines in nuclear power plants (NPPs). The driving coil in the probe is excited by a rectangular current pulse and the resultant response, which is the difference of the two Hall-sensors, has been detected as the PEC probe signal. The discriminating time domain features of the detected pulse such as peak value and time to zero are used to interpret the experimental results with the defects in the test sample. A feature extraction technique such as spectral power density has been devised to infer the PEC response.

A randomized comparison of the effect of two prelinguistic communication interventions on the acquisition of spoken communication in preschoolers with ASD.

PubMed

Yoder, Paul; Stone, Wendy L

2006-08-01

This randomized group experiment compared the efficacy of 2 communication interventions (Responsive Education and Prelinguistic Milieu Teaching [RPMT] and the Picture Exchange Communication System [PECS]) on spoken communication in 36 preschoolers with autism spectrum disorders (ASD). Each treatment was delivered to children for a maximum total of 24 hr over a 6-month period. Spoken communication was assessed in a rigorous test of generalization at pretreatment, posttreatment, and 6-month follow-up periods. PECS was more successful than RPMT in increasing the number of nonimitative spoken communication acts and the number of different nonimitative words used at the posttreatment period. Considering growth over all 3 measurement periods, an exploratory analysis showed that growth rate of the number of different nonimitative words was faster in the PECS group than in the RPMT group for children who began treatment with relatively high object exploration. In contrast, analogous slopes were steeper in the RPMT group than in the PECS group for children who began treatment with relatively low object exploration.

Use of a Picture Exchange Communication System for preventive procedures in individuals with autism spectrum disorder: pilot study.

PubMed

Zink, Adriana Gledys; Diniz, Michele Baffi; Rodrigues Dos Santos, Maria Teresa Botti; Guaré, Renata Oliveira

2016-09-01

The aim of the present study was to evaluate the use of the Picture Exchange Communication System (PECS) in individuals with autism spectrum disorder (ASD) in order to facilitate patient-professional communication during preventive procedures. In this study, 26 patients with ASD, between 5 and 19 years of age (10±3.3 y), were divided into two groups: G1 (n = 13) with no previous experience of dental treatment, and G2 (n = 13), with such previous experience. The initial approach followed the principles of the Son-Rise Program®. The seven PECSs presented the routine of the dental office: "room," "ground," "chair," "dentist," "mouth," "low," and "triple." Each PEC was used up to three times in order to acquire the skill proposed. It was verified that G2 required a greater number of times to achieve the acceptance of PECS "ground," "dentist," "mouth," and "triple" (p < .05). We concluded that PECS facilitated patient-professional communication during preventive procedures, including for ASD patients with previous dental experience. © 2016 Special Care Dentistry Association and Wiley Periodicals, Inc.

Osteoinductive activity of insulin-functionalized cell culture surfaces obtained using diazonium chemistry

PubMed Central

Mikulska, Anna; Filipowska, Joanna; Osyczka, Anna M.; Nowakowska, Maria; Szczubiałka, Krzysztof

2015-01-01

Polymeric surfaces suitable for cell culture (DR/Pec) were constructed from diazoresin (DR) and pectin (Pec) in a form of ultrathin films using the layer-by-layer (LbL) technique. The surfaces were functionalized with insulin using diazonium chemistry. Such functionalized surfaces were used to culture human mesenchymal stem cells (hMSCs) to assess their suitability for bone tissue engineering and regeneration. The activity of insulin immobilized on the surfaces (DR/Pec/Ins) was compared to that of insulin dissolved in the culture medium. Human MSC grown on insulin-immobilized DR/Pec surfaces displayed increased proliferation and higher osteogenic activity. The latter was determined by means of alkaline phosphatase (ALP) activity, which increases at early stages of osteoblasts differentiation. Insulin dissolved in the culture medium did not stimulate cell proliferation and its osteogenic activity was significantly lower. Addition of recombinant human bone morphogenetic protein 2 (rhBMP-2) to the culture medium further increased ALP activity in hMSCs indicating additive osteogenic action of immobilized insulin and rhBMP-2. PMID:25629028

Investigation of the influence of a step change in surface roughness on turbulent heat transfer

NASA Technical Reports Server (NTRS)

Taylor, Robert P.; Coleman, Hugh W.; Taylor, J. Keith; Hosni, M. H.

1991-01-01

The use is studied of smooth heat flux gages on the otherwise very rough SSME fuel pump turbine blades. To gain insights into behavior of such installations, fluid mechanics and heat transfer data were collected and are reported for a turbulent boundary layer over a surface with a step change from a rough surface to a smooth surface. The first 0.9 m length of the flat plate test surface was roughened with 1.27 mm hemispheres in a staggered, uniform array spaced 2 base diameters apart. The remaining 1.5 m length was smooth. The effect of the alignment of the smooth surface with respect to the rough surface was also studied by conducting experiments with the smooth surface aligned with the bases or alternatively with the crests of the roughness elements. Stanton number distributions, skin friction distributions, and boundary layer profiles of temperature and velocity are reported and are compared to previous data for both all rough and all smooth wall cases. The experiments show that the step change from rough to smooth has a dramatic effect on the convective heat transfer. It is concluded that use of smooth heat flux gages on otherwise rough surfaces could cause large errors.

Two-component fluid membranes near repulsive walls: Linearized hydrodynamics of equilibrium and nonequilibrium states.

PubMed

Sankararaman, Sumithra; Menon, Gautam I; Sunil Kumar, P B

2002-09-01

We study the linearized hydrodynamics of a two-component fluid membrane near a repulsive wall, using a model that incorporates curvature-concentration coupling as well as hydrodynamic interactions. This model is a simplified version of a recently proposed one [J.-B. Manneville et al., Phys. Rev. E 64, 021908 (2001)] for nonequilibrium force centers embedded in fluid membranes, such as light-activated bacteriorhodopsin pumps incorporated in phospholipid egg phosphatidyl choline (EPC) bilayers. The pump-membrane system is modeled as an impermeable, two-component bilayer fluid membrane in the presence of an ambient solvent, in which one component, representing active pumps, is described in terms of force dipoles displaced with respect to the bilayer midpoint. We first discuss the case in which such pumps are rendered inactive, computing the mode structure in the bulk as well as the modification of hydrodynamic properties by the presence of a nearby wall. These results should apply, more generally, to equilibrium fluid membranes comprised of two components, in which the effects of curvature-concentration coupling are significant, above the threshold for phase separation. We then discuss the fluctuations and mode structure in the steady state of active two-component membranes near a repulsive wall. We find that proximity to the wall smoothens membrane height fluctuations in the stable regime, resulting in a logarithmic scaling of the roughness even for initially tensionless membranes. This explicitly nonequilibrium result is a consequence of the incorporation of curvature-concentration coupling in our hydrodynamic treatment. This result also indicates that earlier scaling arguments which obtained an increase in the roughness of active membranes near repulsive walls upon neglecting the role played by such couplings may need to be reevaluated.

Genetic podocyte lineage reveals progressive podocytopenia with parietal cell hyperplasia in a murine model of cellular/collapsing focal segmental glomerulosclerosis.

PubMed

Suzuki, Taisei; Matsusaka, Taiji; Nakayama, Makiko; Asano, Takako; Watanabe, Teruo; Ichikawa, Iekuni; Nagata, Michio

2009-05-01

Focal segmental glomerulosclerosis (FSGS) is a progressive renal disease, and the glomerular visceral cell hyperplasia typically observed in cellular/collapsing FSGS is an important pathological factor in disease progression. However, the cellular features that promote FSGS currently remain obscure. To determine both the origin and phenotypic alterations in hyperplastic cells in cellular/collapsing FSGS, the present study used a previously described FSGS model in p21-deficient mice with visceral cell hyperplasia and identified the podocyte lineage by genetic tagging. The p21-deficient mice with nephropathy showed significantly higher urinary protein levels, extracapillary hyperplastic indices on day 5, and glomerular sclerosis indices on day 14 than wild-type controls. X-gal staining and immunohistochemistry for podocyte and parietal epithelial cell (PEC) markers revealed progressive podocytopenia with capillary collapse accompanied by PEC hyperplasia leading to FSGS. In our investigation, non-tagged cells expressed neither WT1 nor nestin. Ki-67, a proliferation marker, was rarely associated with podocytes but was expressed at high levels in PECs. Both terminal deoxynucleotidyl transferase dUTP nick-end labeling staining and electron microscopy failed to show evidence of significant podocyte apoptosis on days 5 and 14. These findings suggest that extensive podocyte loss and simultaneous PEC hyperplasia is an actual pathology that may contribute to the progression of cellular/collapsing FSGS in this mouse model. Additionally, this is the first study to demonstrate the regulatory role of p21 in the PEC cell cycle.

Evolution of the iss gene in Escherichia coli.

PubMed

Johnson, Timothy J; Wannemuehler, Yvonne M; Nolan, Lisa K

2008-04-01

The increased serum survival gene iss has long been recognized for its role in extraintestinal pathogenic Escherichia coli (ExPEC) virulence. iss has been identified as a distinguishing trait of avian ExPEC but not of human ExPEC. This gene has been localized to large virulence plasmids and shares strong similarities with the bor gene from bacteriophage lambda. Here, we demonstrate that three alleles of iss occur among E. coli isolates that appear to have evolved from a common lambda bor precursor. In addition to the occurrence of iss on the ColV/BM virulence plasmids, at least two iss alleles occur within the E. coli chromosome. One of these alleles (designated type 3) was found to occur in the genomes of all currently sequenced ExPEC strains on a similar prophage element that also harbors the Sit iron and manganese transport system. When the prevalence of the three iss types was examined among 487 E. coli isolates, the iss type 3 gene was found to occur at a high frequency among ExPEC isolates, irrespective of the host source. The plasmid-borne iss allele (designated type 1) was highly prevalent among avian pathogenic E. coli and neonatal meningitis-associated E. coli isolates but not among uropathogenic E. coli isolates. This study demonstrates the evolution of iss in E. coli and provides an additional tool for discriminating among E. coli pathotypes through the differentiation of the three iss allele types and bor.

Are exposure predictions, used for the prioritization of pharmaceuticals in the environment, fit for purpose?

PubMed

Burns, Emily E; Thomas-Oates, Jane; Kolpin, Dana W; Furlong, Edward T; Boxall, Alistair B A

2017-10-01

Prioritization methodologies are often used for identifying those pharmaceuticals that pose the greatest risk to the natural environment and to focus laboratory testing or environmental monitoring toward pharmaceuticals of greatest concern. Risk-based prioritization approaches, employing models to derive exposure concentrations, are commonly used, but the reliability of these models is unclear. The present study evaluated the accuracy of exposure models commonly used for pharmaceutical prioritization. Targeted monitoring was conducted for 95 pharmaceuticals in the Rivers Foss and Ouse in the City of York (UK). Predicted environmental concentration (PEC) ranges were estimated based on localized prescription, hydrological data, reported metabolism, and wastewater treatment plant (WWTP) removal rates, and were compared with measured environmental concentrations (MECs). For the River Foss, PECs, obtained using highest metabolism and lowest WWTP removal, were similar to MECs. In contrast, this trend was not observed for the River Ouse, possibly because of pharmaceutical inputs unaccounted for by our modeling. Pharmaceuticals were ranked by risk based on either MECs or PECs. With 2 exceptions (dextromethorphan and diphenhydramine), risk ranking based on both MECs and PECs produced similar results in the River Foss. Overall, these findings indicate that PECs may well be appropriate for prioritization of pharmaceuticals in the environment when robust and local data on the system of interest are available and reflective of most source inputs. Environ Toxicol Chem 2017;36:2823-2832. © 2017 SETAC. © 2017 SETAC.

Comparison of phthalic acid removal from aqueous solution by electrochemical methods: Optimization, kinetic and sludge study.

PubMed

Sandhwar, Vishal Kumar; Prasad, Basheshwar

2017-12-01

In this work, comparative study between electrochemical processes such as electrocoagulation (EC), peroxi-coagulation (PC) and peroxi-electrocoagulation (PEC) was performed for the removal of phthalic acid (PA) and chemical oxygen demand (COD) from aqueous medium. Initially, acid treatment was studied at various pH (1-3) and temperature (10-55 °C). Subsequently, the supernatant was re-treated by electrochemical processes such as EC, PC and PEC separately. Independent parameters viz. pH, current density (CD), electrolyte concentration (m), electrode gap (g), H 2 O 2 concentration and electrolysis time (t) were optimized by Central Composite Design (CCD) for these electrochemical processes. All three processes were compared based on removal, energy consumption, kinetic analysis, operating cost and sludge characteristics. In this study, PEC process was found more efficient among EC, PC and PEC processes in order to get maximum removal, minimum energy consumption and minimum operating cost. Maximum removal of PA- 68.21%, 74.36%, 82.25% & COD- 64.79%, 68.15%, 75.21% with energy consumption - 120.95, 97.51, 65.68 (kWh/kg COD removed) were attained through EC, PC and PEC processes respectively at their corresponding optimum conditions. Results indicated that PA and COD removals are in order of PEC > PC > EC under optimum conditions. First order kinetic model was found able to describe the degradation kinetics and provided best correlation for the removal rate within the acceptable error range. Copyright © 2017 Elsevier Ltd. All rights reserved.

Genomic Microbial Epidemiology Is Needed to Comprehend the Global Problem of Antibiotic Resistance and to Improve Pathogen Diagnosis

PubMed Central

Wyrsch, Ethan R.; Roy Chowdhury, Piklu; Chapman, Toni A.; Charles, Ian G.; Hammond, Jeffrey M.; Djordjevic, Steven P.

2016-01-01

Contamination of waste effluent from hospitals and intensive food animal production with antimicrobial residues is an immense global problem. Antimicrobial residues exert selection pressures that influence the acquisition of antimicrobial resistance and virulence genes in diverse microbial populations. Despite these concerns there is only a limited understanding of how antimicrobial residues contribute to the global problem of antimicrobial resistance. Furthermore, rapid detection of emerging bacterial pathogens and strains with resistance to more than one antibiotic class remains a challenge. A comprehensive, sequence-based genomic epidemiological surveillance model that captures essential microbial metadata is needed, both to improve surveillance for antimicrobial resistance and to monitor pathogen evolution. Escherichia coli is an important pathogen causing both intestinal [intestinal pathogenic E. coli (IPEC)] and extraintestinal [extraintestinal pathogenic E. coli (ExPEC)] disease in humans and food animals. ExPEC are the most frequently isolated Gram negative pathogen affecting human health, linked to food production practices and are often resistant to multiple antibiotics. Cattle are a known reservoir of IPEC but they are not recognized as a source of ExPEC that impact human or animal health. In contrast, poultry are a recognized source of multiple antibiotic resistant ExPEC, while swine have received comparatively less attention in this regard. Here, we review what is known about ExPEC in swine and how pig production contributes to the problem of antibiotic resistance. PMID:27379026

Light harvesting proteins for solar fuel generation in bioengineered photoelectrochemical cells.

PubMed

Ihssen, Julian; Braun, Artur; Faccio, Greta; Gajda-Schrantz, Krisztina; Thöny-Meyer, Linda

2014-01-01

The sun is the primary energy source of our planet and potentially can supply all societies with more than just their basic energy needs. Demand of electric energy can be satisfied with photovoltaics, however the global demand for fuels is even higher. The direct way to produce the solar fuel hydrogen is by water splitting in photoelectrochemical (PEC) cells, an artificial mimic of photosynthesis. There is currently strong resurging interest for solar fuels produced by PEC cells, but some fundamental technological problems need to be solved to make PEC water splitting an economic, competitive alternative. One of the problems is to provide a low cost, high performing water oxidizing and oxygen evolving photoanode in an environmentally benign setting. Hematite, α-Fe2O3, satisfies many requirements for a good PEC photoanode, but its efficiency is insufficient in its pristine form. A promising strategy for enhancing photocurrent density takes advantage of photosynthetic proteins. In this paper we give an overview of how electrode surfaces in general and hematite photoanodes in particular can be functionalized with light harvesting proteins. Specifically, we demonstrate how low-cost biomaterials such as cyanobacterial phycocyanin and enzymatically produced melanin increase the overall performance of virtually no-cost metal oxide photoanodes in a PEC system. The implementation of biomaterials changes the overall nature of the photoanode assembly in a way that aggressive alkaline electrolytes such as concentrated KOH are not required anymore. Rather, a more environmentally benign and pH neutral electrolyte can be used.

Cell Permeating Nano-Complexes of Amphiphilic Polyelectrolytes Enhance Solubility, Stability, and Anti-Cancer Efficacy of Curcumin.

PubMed

Fatima, Munazza T; Chanchal, Abhishek; Yavvari, Prabhu S; Bhagat, Somnath D; Gujrati, Mansi; Mishra, Ram K; Srivastava, Aasheesh

2016-07-11

Many hydrophobic drugs encounter severe bioavailability issues owing to their low aqueous solubility and limited cellular uptake. We have designed a series of amphiphilic polyaspartamide polyelectrolytes (PEs) that solubilize such hydrophobic drugs in aqueous medium and enhance their cellular uptake. These PEs were synthesized through controlled (∼20 mol %) derivatization of polysuccinimide (PSI) precursor polymer with hydrophobic amines (of varying alkyl chain lengths, viz. hexyl, octyl, dodecyl, and oleyl), while the remaining succinimide residues of PSI were opened using a protonable and hydrophilic amine, 2-(2-amino-ethyl amino) ethanol (AE). Curcumin (Cur) was employed as a representative hydrophobic drug to explore the drug-delivery potential of the resulting PEs. Unprecedented enhancement in the aqueous solubility of Cur was achieved by employing these PEs through a rather simple protocol. In the case of PEs containing oleyl/dodecyl residues, up to >65000× increment in the solubility of Cur in aqueous medium could be achieved without requiring any organic solvent at all. The resulting suspensions were physically and chemically stable for at least 2 weeks. Stable nanosized polyelectrolyte complexes (PECs) with average hydrodynamic diameters (DH) of 150-170 nm (without Cur) and 220-270 nm (after Cur loading) were obtained by using submolar sodium polyaspartate (SPA) counter polyelectrolyte. The zeta potential of these PECs ranged from +36 to +43 mV. The PEC-formation significantly improved the cytocompatibility of the PEs while affording reconstitutable nanoformulations having up to 40 wt % drug-loading. The Cur-loaded PECs were readily internalized by mammalian cells (HEK-293T, MDA-MB-231, and U2OS), majorly through clathrin-mediated endocytosis (CME). Cellular uptake of Cur was directly correlated with the length of the alkyl chain present in the PECs. Further, the PECs significantly improved nuclear transport of Cur in cancer cells, resulting in their death by apoptosis. Noncancerous cells were completely unaffected under this treatment.

Generation of a functional and durable vascular niche by the adenoviral E4ORF1 gene

PubMed Central

Seandel, Marco; Butler, Jason M.; Kobayashi, Hideki; Hooper, Andrea T.; White, Ian A.; Zhang, Fan; Vertes, Eva L.; Kobayashi, Mariko; Zhang, Yan; Shmelkov, Sergey V.; Hackett, Neil R.; Rabbany, Sina; Boyer, Julie L.; Rafii, Shahin

2008-01-01

Vascular cells contribute to organogenesis and tumorigenesis by producing unknown factors. Primary endothelial cells (PECs) provide an instructive platform for identifying factors that support stem cell and tumor homeostasis. However, long-term maintenance of PECs requires stimulation with cytokines and serum, resulting in loss of their angiogenic properties. To circumvent this hurdle, we have discovered that the adenoviral E4ORF1 gene product maintains long-term survival and facilitates organ-specific purification of PECs, while preserving their vascular repertoire for months, in serum/cytokine-free cultures. Lentiviral introduction of E4ORF1 into human PECs (E4ORF1+ ECs) increased the long-term survival of these cells in serum/cytokine-free conditions, while preserving their in vivo angiogenic potential for tubulogenesis and sprouting. Although E4ORF1, in the absence of mitogenic signals, does not induce proliferation of ECs, stimulation with VEGF-A and/or FGF-2 induced expansion of E4ORF1+ ECs in a contact-inhibited manner. Indeed, VEGF-A-induced phospho MAPK activation of E4ORF1+ ECs is comparable with that of naive PECs, suggesting that the VEGF receptors remain functional upon E4ORF1 introduction. E4ORF1+ ECs inoculated in implanted Matrigel plugs formed functional, patent, humanized microvessels that connected to the murine circulation. E4ORF1+ ECs also incorporated into neo-vessels of human tumor xenotransplants and supported serum/cytokine-free expansion of leukemic and embryonal carcinoma cells. E4ORF1 augments survival of PECs in part by maintaining FGF-2/FGF-R1 signaling and through tonic Ser-473 phosphorylation of Akt, thereby activating the mTOR and NF-κB pathways. Therefore, E4ORF1+ ECs establish an Akt-dependent durable vascular niche not only for expanding stem and tumor cells but also for interrogating the roles of vascular cells in regulating organ-specific vascularization and tumor neo-angiogenesis. PMID:19036927

Efficacy and Safety of Ketamine Added to Local Anesthetic in Modified Pectoral Block for Management of Postoperative Pain in Patients Undergoing Modified Radical Mastectomy.

PubMed

Othman, Ahmed H; El-Rahman, Ahmad M Abd; El Sherif, Fatma

2016-01-01

Breast surgery is an exceedingly common procedure with an increased incidence of acute and chronic pain. Pectoral nerve block is a novel peripheral nerve block alternative to neuro-axial and paravertebral blocks for ambulatory breast surgeries. This study aims to compare the analgesic efficacy and safety of modified Pecs block with ketamine plus bupivacaine versus bupivacaine in patients undergoing breast cancer surgery. A randomized, double-blind, prospective study. Academic medical center. This study is registered at www.clinicaltrials.gov under number: (NCT02620371) after approval by the ethics committee of South Egypt Cancer Institute, Assuit University, Assuit, Egypt. Sixty patients aged 18 - 60 years scheduled for modified radical mastectomy were enrolled and randomly assigned into 2 groups (30 patients each): Control group patients were given ultrasound-guided, Pecs block with 30 mL of 0.25% bupivacaine only. Ketamine group patients were given ultrasound-guided, Pecs block with 30 mL of 0.25% bupivacaine plus ketamine hydrochloride (1 mg/kg). Patients were followed up for 48 hours postoperatively for vital signs, VAS score, first request of rescue analgesia and total morphine consumption, sedation score, and side effects. Ketamine plus bupivacaine in Pecs block compared to bupivacaine alone prolonged the mean time of first request of analgesia (18.25 ± 1.98), (12.56 ± 2.64), respectively (P < 0.001), reduced total morphine consumption (12.50 ± 4.63), (18.86 ± 6.28), respectively (P = 0.016). With no significant difference in hemodynamics, respiratory rate, oxygen saturation, VAS and sedation scores, and side effects observed between the 2 groups (P > 0.05). This study is limited by its sample size. The addition of ketamine to modified Pecs block prolonged the time to first request of analgesia and reduced total opioid consumption without serious side effects in patients who underwent a modified radical mastectomy. Ketamine, bupivacaine, pecs block, postoperative, pain, breast cancer.

Generation of a functional and durable vascular niche by the adenoviral E4ORF1 gene.

PubMed

Seandel, Marco; Butler, Jason M; Kobayashi, Hideki; Hooper, Andrea T; White, Ian A; Zhang, Fan; Vertes, Eva L; Kobayashi, Mariko; Zhang, Yan; Shmelkov, Sergey V; Hackett, Neil R; Rabbany, Sina; Boyer, Julie L; Rafii, Shahin

2008-12-09

Vascular cells contribute to organogenesis and tumorigenesis by producing unknown factors. Primary endothelial cells (PECs) provide an instructive platform for identifying factors that support stem cell and tumor homeostasis. However, long-term maintenance of PECs requires stimulation with cytokines and serum, resulting in loss of their angiogenic properties. To circumvent this hurdle, we have discovered that the adenoviral E4ORF1 gene product maintains long-term survival and facilitates organ-specific purification of PECs, while preserving their vascular repertoire for months, in serum/cytokine-free cultures. Lentiviral introduction of E4ORF1 into human PECs (E4ORF1(+) ECs) increased the long-term survival of these cells in serum/cytokine-free conditions, while preserving their in vivo angiogenic potential for tubulogenesis and sprouting. Although E4ORF1, in the absence of mitogenic signals, does not induce proliferation of ECs, stimulation with VEGF-A and/or FGF-2 induced expansion of E4ORF1(+) ECs in a contact-inhibited manner. Indeed, VEGF-A-induced phospho MAPK activation of E4ORF1(+) ECs is comparable with that of naive PECs, suggesting that the VEGF receptors remain functional upon E4ORF1 introduction. E4ORF1(+) ECs inoculated in implanted Matrigel plugs formed functional, patent, humanized microvessels that connected to the murine circulation. E4ORF1(+) ECs also incorporated into neo-vessels of human tumor xenotransplants and supported serum/cytokine-free expansion of leukemic and embryonal carcinoma cells. E4ORF1 augments survival of PECs in part by maintaining FGF-2/FGF-R1 signaling and through tonic Ser-473 phosphorylation of Akt, thereby activating the mTOR and NF-kappaB pathways. Therefore, E4ORF1(+) ECs establish an Akt-dependent durable vascular niche not only for expanding stem and tumor cells but also for interrogating the roles of vascular cells in regulating organ-specific vascularization and tumor neo-angiogenesis.

Symposium on Numerical and Physical Aspects of Aerodynamic Flows

DTIC Science & Technology

1992-01-15

ReT/R. -1 wide range of Mach numbers including pressure gradient, a = - (a*) (10) surface roughness. surface heating and cooling . and surface 9 I + ReT...and specific heat at constant pressure, respectively. Favre equation is then obtained by contracting the Reynolds-stress decomposition is applied to...their near- wall behavior. In other words, if highly cooled -wall flows are to be predicted correctly, heat fluxes should be modeled e = 2ak + 4bky

F14:A-:B- and IncX4 Inc group cfr-positive plasmids circulating in Escherichia coli of animal origin in Northeast China.

PubMed

Wang, Xiumei; Zhu, Yao; Hua, Xin; Chen, Fuguang; Wang, Changzhen; Zhang, Yanhe; Liu, Siguo; Zhang, Wanjiang

2018-04-01

The objective of this study was to investigate the prevalence of the cfr gene in Escherichia coli isolates from domestic animals in Northeast China and to characterize the cfr-containing plasmids. Between June 2015 and April 2016, 370 E. coli isolates were collected from pigs, chickens, and dairy cows in Northeast China. Among these, 111 were florfenicol resistant, including 109 isolates carrying the floR gene and 6 positives for cfr. The prevalence of cfr in E. coli isolates from the four northeast provinces in China was 1.6% (6/370), which was higher than that previously reported (0.08% and 0.5%). All six cfr-containing E. coli isolates were highly resistant to florfenicol (100%), cefotaxime (100%), and fosfomycin (100%). Complete sequence analysis of two cfr-carrying plasmids revealed high homology of the IncX4-type pEC14cfr plasmid with two other cfr-harboring plasmids, pSD11 and pGXEC6, found in swine E. coli isolates from southern China. pEC14cfr-like plasmids have been isolated in five provinces in southern and northern China. The isolation sites were up to 2700 kilometers apart, implying that pEC14cfr-like plasmids are likely to be national epidemic cfr-carrying plasmids that mediate the dissemination of cfr in China. Moreover, the genetic structure (IS26-IS26-cfr-rec-pre/mob-ramA-IS26) of the second cfr-carrying plasmid, IncF14:A-:B- pEC295cfr, represents a novel genetic environment for cfr identified for the first time in the present study. Sequence homology analysis indicated that the cfr-carrying element was most likely introduced into a cfr-negative pEC12 plasmid backbone, which evolved into the cfr-carrying vector, pEC295cfr. Moreover, isolation of the IncF14:A-:B- pEC295cfr plasmid harboring cfr suggests that IncFII plasmids maybe have become additional effective vehicles for cfr dissemination. These results highlight the importance of surveying the prevalence of IncX4 and IncFII plasmids in gram-negative bacteria, especially in swine E. coli isolates. Copyright © 2018 Elsevier B.V. All rights reserved.

Development of an E-H2O2/TiO2 photoelectrocatalytic oxidation system for water and wastewater treatment.

PubMed

Li, X Z; Liu, H S

2005-06-15

In this study, an innovative E-H2O2/TiO2 (E-H2O2 = electrogenerated hydrogen peroxide) photoelectrocatalytic (PEC) oxidation system was successfully developed for water and wastewater treatment. A TiO2/Ti mesh electrode was applied in this photoreactor as the anode to conduct PEC oxidation, and a reticulated vitreous carbon (RVC) electrode was used as the cathode to electrogenerate hydrogen peroxide simultaneously. The TiO2/Ti mesh electrode was prepared with a modified anodic oxidation process in a quadrielectrolyte (H2SO4-H3PO4-H2O2-HF) solution. The crystal structure, surface morphology, and film thickness of the TiO2/Ti mesh electrode were characterized by X-ray diffraction and scanning electron microscopy. The analytical results showed that a honeycomb-type anatase film with a thickness of 5 microm was formed. Photocatalytic oxidation (PC) and PEC oxidation of 2,4,6-trichlorophenol (TCP) in an aqueous solution were performed under various experimental conditions. Experimental results showed that the TiO2/Ti electrode, anodized in the H2SO4-H3PO4-H2O2-HF solution, had higher photocatalytic activity than the TiO2/Ti electrode anodized in the H2SO4 solution. It was found that the maximum applied potential would be around 2.5 V, corresponding to an optimum applied current density of 50 microA cm(-2) under UV-A illumination. The experiments confirmed that the E-H2O2 on the RVC electrode can significantly enhance the PEC oxidation of TCP in aqueous solution. The rate of TCP degradation in such an E-H2O2-assisted TiO2 PEC reaction was 5.0 times that of the TiO2 PC reaction and 2.3 times that of the TiO2 PEC reaction. The variation of pH during the E-H2O2-assisted TiO2 PEC reaction, affected by individual reactions, was also investigated. It was found that pH was well maintained during the TCP degradation in such an E-H2O2/TiO2 reaction system. This is beneficial to TCP degradation in an aqueous solution.

Demonstration of electronic design automation flow for massively parallel e-beam lithography

NASA Astrophysics Data System (ADS)

Brandt, Pieter; Belledent, Jérôme; Tranquillin, Céline; Figueiro, Thiago; Meunier, Stéfanie; Bayle, Sébastien; Fay, Aurélien; Milléquant, Matthieu; Icard, Beatrice; Wieland, Marco

2014-07-01

For proximity effect correction in 5 keV e-beam lithography, three elementary building blocks exist: dose modulation, geometry (size) modulation, and background dose addition. Combinations of these three methods are quantitatively compared in terms of throughput impact and process window (PW). In addition, overexposure in combination with negative bias results in PW enhancement at the cost of throughput. In proximity effect correction by over exposure (PEC-OE), the entire layout is set to fixed dose and geometry sizes are adjusted. In PEC-dose to size (DTS) both dose and geometry sizes are locally optimized. In PEC-background (BG), a background is added to correct the long-range part of the point spread function. In single e-beam tools (Gaussian or Shaped-beam), throughput heavily depends on the number of shots. In raster scan tools such as MAPPER Lithography's FLX 1200 (MATRIX platform) this is not the case and instead of pattern density, the maximum local dose on the wafer is limiting throughput. The smallest considered half-pitch is 28 nm, which may be considered the 14-nm node for Metal-1 and the 10-nm node for the Via-1 layer, achieved in a single exposure with e-beam lithography. For typical 28-nm-hp Metal-1 layouts, it was shown that dose latitudes (size of process window) of around 10% are realizable with available PEC methods. For 28-nm-hp Via-1 layouts this is even higher at 14% and up. When the layouts do not reach the highest densities (up to 10∶1 in this study), PEC-BG and PEC-OE provide the capability to trade throughput for dose latitude. At the highest densities, PEC-DTS is required for proximity correction, as this method adjusts both geometry edges and doses and will reduce the dose at the densest areas. For 28-nm-hp lines critical dimension (CD), hole&dot (CD) and line ends (edge placement error), the data path errors are typically 0.9, 1.0 and 0.7 nm (3σ) and below, respectively. There is not a clear data path performance difference between the investigated PEC methods. After the simulations, the methods were successfully validated in exposures on a MAPPER pre-alpha tool. A 28-nm half pitch Metal-1 and Via-1 layouts show good performance in resist that coincide with the simulation result. Exposures of soft-edge stitched layouts show that beam-to-beam position errors up to ±7 nm specified for FLX 1200 show no noticeable impact on CD. The research leading to these results has been performed in the frame of the industrial collaborative consortium IMAGINE.

Extraintestinal pathogenic Escherichia coli O1:K1:H7/NM from human and avian origin: detection of clonal groups B2 ST95 and D ST59 with different host distribution.

PubMed

Mora, Azucena; López, Cecilia; Dabhi, Ghizlane; Blanco, Miguel; Blanco, Jesús E; Alonso, María Pilar; Herrera, Alexandra; Mamani, Rosalía; Bonacorsi, Stéphane; Moulin-Schouleur, Maryvonne; Blanco, Jorge

2009-07-07

Extraintestinal pathogenic Escherichia coli (ExPEC) strains of serotype O1:K1:H7/NM are frequently implicated in neonatal meningitis, urinary tract infections and septicemia in humans. They are also commonly isolated from colibacillosis in poultry. Studies to determine the similarities of ExPEC from different origins have indicated that avian strains potentially have zoonotic properties. A total of 59 ExPEC O1:K1:H7/NM isolates (21 from avian colibacillosis, 15 from human meningitis, and 23 from human urinary tract infection and septicemia) originated from four countries were characterized by phylogenetic PCR grouping, Multilocus Sequence Typing (MLST), Pulsed Field Gel Electrophoresis (PFGE) and genotyping based on several genes known for their association with ExPEC or avian pathogenic Escherichia coli (APEC) virulence.APEC and human ExPEC isolates differed significantly in their assignments to phylogenetic groups, being phylogroup B2 more prevalent among APEC than among human ExPEC (95% vs. 53%, P = 0.001), whereas phylogroup D was almost exclusively associated with human ExPEC (47% vs. 5%, P = 0.0000). Seven virulence genes showed significant differences, being fimAvMT78 and sat genes linked to human isolates, while papGII, tsh, iron, cvaC and iss were significantly associated to APEC. By MLST, 39 of 40 ExPEC belonging to phylogroup B2, and 17 of 19 belonging to phylogroup D exhibited the Sequence Types (STs) ST95 and ST59, respectively. Additionally, two novel STs (ST1013 and ST1006) were established. Considering strains sharing the same ST, phylogenetic group, virulence genotype and PFGE cluster to belong to the same subclone, five subclones were detected; one of those grouped six strains of human and animal origin from two countries. Present results reveal that the clonal group B2 O1:K1:H7/NM ST95, detected in strains of animal and human origin, recovered from different dates and geographic sources, provides evidence that some APEC isolates may act as potential pathogens for humans and, consequently, poultry as a foodborne source, suggesting no host specificity for this type of isolates. A novel and important finding has been the detection of the clonal group D O1:K1:H7/NM ST59 almost exclusively in humans, carrying pathogenic genes linked to the phylogenetic group D. This finding would suggest D O1:K1:H7/NM ST59 as a host specific pathotype for humans.

Institute for Aviation Research and Development Research Project

DTIC Science & Technology

1989-01-01

Symbolics Artificial Intelligence * Vision Systems * Finite Element Modeling ( NASTRAN ) * Aerodynamic Paneling (VSAERO) Projects: * Software...34Wall Functions for k and epsilon for Turbulent Flow Through Rough and Smooth Pipes," Eleventh International Symposium on Turbulence, October 17-19, 1988

Hydraulic Roughness and Flow Resistance in a Subglacial Conduit

NASA Astrophysics Data System (ADS)

Chen, Y.; Liu, X.; Mankoff, K. D.

2017-12-01

The hydraulic roughness significantly affects the flow resistance in real subglacial conduits, but has been poorly understood. To address this knowledge gap, this paper first proposes a procedure to define and quantify the geometry roughness, and then relates such a geometry roughness to the hydraulic roughness based on a series of computational fluid dynamics (CFD) simulations. The results indicate that by using the 2nd order structure function, the roughness field can be well quantified by the powers of the scaling-law, the vertical and horizontal length scales of the structure functions. The vertical length scale can be further chosen as the standard deviation of the roughness field σr. The friction factors calculated from either total drag force or the linear decreasing pressure agree very well with those calculated from traditional rough pipe theories when the equivalent hydraulic roughness height is corrected as ks = (1.1 ˜ 1.5)σr. This result means that the fully rough pipe resistance formula λ = [2 log(D0/2ks) + 1.74]-2, and the Moody diagram are still valid for the friction factor estimation in subglacial conduits when σr /D0<18% and ks/D0<22%. The results further show that when a proper hydraulic roughness is determined, the total flow resistance corresponding to the given hydraulic roughness height can be accurately modelled by using a rough wall function. This suggests that the flow resistance for the longer realistic subglacial conduits with large sinuosity and cross-sectional variations may be correctly predicted by CFD simulations. The results also show that the friction factors from CFD modeling are much larger than those determined from traditional rough pipe theories when σr /D0>20%.

Phase-field study of grain boundary tracking behavior in crack-seal microstructures

NASA Astrophysics Data System (ADS)

Ankit, Kumar; Nestler, Britta; Selzer, Michael; Reichardt, Mathias

2013-12-01

In order to address the growth of crystals in veins, a multiphase-field model is used to capture the dynamics of crystals precipitating from a super-saturated solution. To gain a detailed understanding of the polycrystal growth phenomena in veins, we investigate the influence of various boundary conditions on crystal growth. In particular, we analyze the formation of vein microstructures resulting from the free growth of crystals as well as crack-sealing processes. We define the crystal symmetry by considering the anisotropy in surface energy to simulate crystals with flat facets and sharp corners. The resulting growth competition of crystals with different orientations is studied to deduce a consistent orientation selection rule in the free-growth regime. Using crack-sealing simulations, we correlate the grain boundary tracking behavior depending on the relative rate of crack opening, opening trajectory, initial grain size, and wall roughness. Further, we illustrate how these parameters induce the microstructural transition between blocky (crystals growing anisotropically) to fibrous morphology (isotropic) and formation of grain boundaries. The phase-field simulations of crystals in the free-growth regime (in 2D and 3D) indicate that the growth or consumption of a crystal is dependent on the orientation difference with neighboring crystals. The crack-sealing simulation results (in 2D and 3D) reveal that crystals grow isotropically and grain boundaries track the opening trajectory if the wall roughness is high, opening increments are small, and crystals touch the wall before the next crack increment starts. Further, we find that within the complete crack-seal regime, anisotropy in surface energy results in the formation of curved/oscillating grain boundaries (instead of straight) when the crack-opening velocity is increased and wall roughness is not sufficiently high. Additionally, the overall capability of phase-field method to simulate large-scale polycrystal growth in veins (in 3D) is demonstrated enumerating the main advantages of adopting the novel approach.

Application of Plenoptic PIV for 3D Velocity Measurements Over Roughness Elements in a Refractive Index Matched Facility

NASA Astrophysics Data System (ADS)

Thurow, Brian; Johnson, Kyle; Kim, Taehoon; Blois, Gianluca; Best, Jim; Christensen, Ken

2014-11-01

The application of Plenoptic PIV in a Refractive Index Matched (RIM) facility housed at Illinois is presented. Plenoptic PIV is an emerging 3D diagnostic that exploits the light-field imaging capabilities of a plenoptic camera. Plenoptic cameras utilize a microlens array to measure the position and angle of light rays captured by the camera. 3D/3C velocity fields are determined through application of the MART algorithm for volume reconstruction and a conventional 3D cross-correlation PIV algorithm. The RIM facility is a recirculating tunnel with a 62.5% aqueous solution of sodium iodide used as the working fluid. Its resulting index of 1.49 is equal to that of acrylic. Plenoptic PIV was used to measure the 3D velocity field of a turbulent boundary layer flow over a smooth wall, a single wall-mounted hemisphere and a full array of hemispheres (i.e. a rough wall) with a k/ δ ~ 4.6. Preliminary time averaged and instantaneous 3D velocity fields will be presented. This material is based upon work supported by the National Science Foundation under Grant No. 1235726.

A Review of the Efficacy of the Picture Exchange Communication System Intervention

ERIC Educational Resources Information Center

Preston, Deborah; Carter, Mark

2009-01-01

The Picture Exchange Communication System (PECS) is a communication program that has become widely used, especially with children with autism. This paper reports the results of a review of the empirical literature on PECS. A descriptive review is provided of the 27 studies identified, which included randomized controlled trials (RCTs), other group…

Comparison of PECS and the Use of a VOCA: A Replication

ERIC Educational Resources Information Center

Beck, Ann R.; Stoner, Julia B.; Bock, Stacey J.; Parton, Tom

2008-01-01

This study compares use of the Picture Exchange Communication System (PECS) and a Voice Output Communication Aide (VOCA) with four preschool children who were either non-speaking or limited in their ability to speak and did not use an AAC system to communicate functionally. An alternating treatment single subject design was used to measure…

Comparative Efficacy of the Picture Exchange Communication System (PECS) versus a Speech-Generating Device: Effects on Requesting Skills

ERIC Educational Resources Information Center

Boesch, Miriam C.; Wendt, Oliver; Subramanian, Anu; Hsu, Ning

2013-01-01

An experimental, single-subject research study investigated the comparative efficacy of the Picture Exchange Communication System (PECS) versus a speech-generating device (SGD) in developing requesting skills for three elementary-age children with severe autism and little to no functional speech. Results demonstrated increases in requesting…

The Effectiveness of Picture Exchange Communication System (PECS) Training for Teachers of Children with Autism: A Pragmatic, Group Randomised Controlled Trial

ERIC Educational Resources Information Center

Howlin, Patricia; Gordon, R. Kate; Pasco, Greg; Wade, Angie; Charman, Tony

2007-01-01

Objective: To assess the effectiveness of expert training and consultancy for teachers of children with autism spectrum disorder in the use of the Picture Exchange Communication System (PECS). Method: Design: Group randomised, controlled trial (3 groups: immediate treatment, delayed treatment, no treatment). Participants: 84 elementary school…

PECS and VOCAs to Enable Students with Developmental Disabilities to Make Requests: An Overview of the Literature

ERIC Educational Resources Information Center

Lancioni, Giulio E.; O'Reilly, Mark F.; Cuvo, Anthony J.; Singh, Nirbhay N.; Sigafoos, Jeff; Didden, Robert

2007-01-01

This paper provides an overview of the literature dealing with the use of the Picture Exchange Communication System (PECS) and voice output communication aids (VOCAs) for promoting the performance of requests by students with developmental disabilities. Computerized and manual searches were carried out to identify the studies published during the…

The Effects of Parent-Implemented PECS Training on Improvisation of Mands by Children with Autism

ERIC Educational Resources Information Center

Chaabane, Delia B. Ben; Alber-Morgan, Sheila R.; DeBar, Ruth M.

2009-01-01

The present study examined the extent to which mothers were able to train their children, 2 boys with autism, to exchange novel pictures to request items using the picture exchange communication system (PECS). Generalization probes assessing each child's ability to mand for untrained items were conducted throughout conditions. Using a multiple…

Black Leadership and Outside Allies in Virginia Freedom Schools

ERIC Educational Resources Information Center

Bonastia, Christopher

2016-01-01

In July 1963, students from Queens College (QC) and a group of New York City teachers traveled to Prince Edward County (PEC), Virginia, to teach local black youth in Freedom Schools. The county had eliminated public education four years earlier to avoid a desegregation order. PEC Freedom Schools represented the first major effort to recruit an…

Electron-helium S-wave model benchmark calculations. II. Double ionization, single ionization with excitation, and double excitation

NASA Astrophysics Data System (ADS)

Bartlett, Philip L.; Stelbovics, Andris T.

2010-02-01

The propagating exterior complex scaling (PECS) method is extended to all four-body processes in electron impact on helium in an S-wave model. Total and energy-differential cross sections are presented with benchmark accuracy for double ionization, single ionization with excitation, and double excitation (to autoionizing states) for incident-electron energies from threshold to 500 eV. While the PECS three-body cross sections for this model given in the preceding article [Phys. Rev. A 81, 022715 (2010)] are in good agreement with other methods, there are considerable discrepancies for these four-body processes. With this model we demonstrate the suitability of the PECS method for the complete solution of the electron-helium system.

Impacts of a PECS instructional coaching intervention on practitioners and children with autism.

PubMed

Ganz, Jennifer B; Goodwyn, Fara D; Boles, Margot M; Hong, Ee Rea; Rispoli, Mandy J; Lund, Emily M; Kite, Elizabeth

2013-09-01

There is a growing research literature on the potential benefits of augmentative and alternative communication (AAC) for individuals with autism; however few studies have investigated implementation of AAC within real-life contexts. Thus, the purpose of this study was to investigate the impact of training for practitioners in implementation of aided AAC, and to examine implementation of Picture Exchange Communication System (PECS) in real-life contexts. In particular, this study involved the implementation of instructional coaching to increase opportunities offered by behavioral therapists for their preschool-aged clients to use PECS to make requests. Results indicated increases in therapist implementation of AAC and client use of AAC in trained contexts, with limited generalization to untrained contexts.

Randomized comparison of two communication interventions for preschoolers with autism spectrum disorders.

PubMed

Yoder, Paul; Stone, Wendy L

2006-06-01

This randomized group experiment compared the efficacy of 2 communication interventions (Responsive Education and Prelinguistic Milieu Teaching [RPMT] and the Picture Exchange Communication System [PECS]) in 36 preschoolers with autism spectrum disorders. Each treatment was delivered 3 times per week, in 20-min sessions, for 6 months. The results revealed that the RPMT facilitated the frequency of generalized turn taking and generalized initiating joint attention more than did the PECS. The latter effect occurred only for children who began treatment with at least some initiating joint attention. In contrast, the PECS facilitated generalized requests more than the RPMT in children with very little initiating joint attention prior to treatment. These effect sizes were large. Copyright 2006 APA, all rights reserved.

Brief Report: Randomized Test of the Efficacy of Picture Exchange Communication System on Highly Generalized Picture Exchanges in Children with ASD

PubMed Central

Lieberman, Rebecca G.

2014-01-01

A randomized control trial comparing two social-communication interventions in young children with autism examined far-transfer of the use of picture exchange to communicate. Thirty-six children were randomly assigned to one of two treatment conditions, one of which was the Picture Exchange Communication System (PECS). All children had access to picture symbols during assessments. Post-treatment measurement of the number of picture exchanges in a far-transfer, assessment context favored the PECS intervention. These findings were interpreted as support for the hypothesis that the PECS curriculum can successfully teach a generalized means of showing coordinated attention to object and person without requiring eye contact to children with ASD. PMID:19904596

Understanding the brain-behaviour relationship in persons with ASD: implications for PECS as a treatment choice.

PubMed

Ogletree, Billy T; Morrow-Odom, K Leigh; Westling, David

2015-04-01

This article presents emerging neurological findings in Autism Spectrum Disorders (ASD) with particular attention to how this information might inform treatment practices addressing communication impairments. The article begins with a general discussion of the brain-behaviour relationship and moves to the presentation of recent research findings related to ASD. There is particular attention to individuals with autism who are either non-verbal or present emergent verbal abilities. A specific communication treatment, the Picture Exchange Communication System (PECS), is presented as an example of an intervention that addresses the learner needs of many individuals with ASD. The success of PECS is discussed within the context of its fit with brain-based learner characteristics.

Brief Report: Randomized test of the efficacy of picture exchange communication system on highly generalized picture exchanges in children with ASD.

PubMed

Yoder, Paul J; Lieberman, Rebecca G

2010-05-01

A randomized control trial comparing two social-communication interventions in young children with autism examined far-transfer of the use of picture exchange to communicate. Thirty-six children were randomly assigned to one of two treatment conditions, one of which was the Picture Exchange Communication System (PECS). All children had access to picture symbols during assessments. Post-treatment measurement of the number of picture exchanges in a far-transfer, assessment context favored the PECS intervention. These findings were interpreted as support for the hypothesis that the PECS curriculum can successfully teach a generalized means of showing coordinated attention to object and person without requiring eye contact to children with ASD.

Local distribution of wall static pressure and heat transfer on a rough flat plate impinged by a slot air jet

NASA Astrophysics Data System (ADS)

Meda, Adimurthy; Katti, Vadiraj V.

2017-08-01

The present work experimentally investigates the local distribution of wall static pressure and the heat transfer coefficient on a rough flat plate impinged by a slot air jet. The experimental parameters include, nozzle-to-plate spacing (Z /D h = 0.5-10.0), axial distance from stagnation point ( x/D h ), size of detached rib ( b = 4-12 mm) and Reynolds number ( Re = 2500-20,000). The wall static pressure on the surface is recorded using a Pitot tube and a differential pressure transmitter. Infrared thermal imaging technique is used to capture the temperature distribution on the target surface. It is observed that, the maximum wall static pressure occurs at the stagnation point ( x/D h = 0) for all nozzle-to-plate spacing ( Z/D h ) and rib dimensions studied. Coefficient of wall static pressure ( C p ) decreases monotonically with x/D h . Sub atmospheric pressure is evident in the detached rib configurations for jet to plate spacing up to 6.0 for all ribs studied. Sub atmospheric region is stronger at Z/D h = 0.5 due to the fluid accelerating under the rib. As nozzle to plate spacing ( Z/D h ) increases, the sub-atmospheric region becomes weak and vanishes gradually. Reasonable enhancement in both C p as well as Nu is observed for the detached rib configuration. Enhancement is found to decrease with the increase in the rib width. The results of the study can be used in optimizing the cooling system design.

Wake Instabilities Behind Discrete Roughness Elements in High Speed Boundary Layers

NASA Technical Reports Server (NTRS)

Choudhari, Meelan; Li, Fei; Chang, Chau-Lyan; Norris, Andrew; Edwards, Jack

2013-01-01

Computations are performed to study the flow past an isolated, spanwise symmetric roughness element in zero pressure gradient boundary layers at Mach 3.5 and 5.9, with an emphasis on roughness heights of less than 55 percent of the local boundary layer thickness. The Mach 5.9 cases include flow conditions that are relevant to both ground facility experiments and high altitude flight ("cold wall" case). Regardless of the Mach number, the mean flow distortion due to the roughness element is characterized by long-lived streamwise streaks in the roughness wake, which can support instability modes that did not exist in the absence of the roughness element. The higher Mach number cases reveal a variety of instability mode shapes with velocity fluctuations concentrated in different localized regions of high base flow shear. The high shear regions vary from the top of a mushroom shaped structure characterizing the centerline streak to regions that are concentrated on the sides of the mushroom. Unlike the Mach 3.5 case with nearly same values of scaled roughness height k/delta and roughness height Reynolds number Re(sub kk), the odd wake modes in both Mach 5.9 cases are significantly more unstable than the even modes of instability. Additional computations for a Mach 3.5 boundary layer indicate that the presence of a roughness element can also enhance the amplification of first mode instabilities incident from upstream. Interactions between multiple roughness elements aligned along the flow direction are also explored.

Preliminary Note on a Correlation of a Boundary-Layer Transition Results on Highly Cooled Blunt Bodies

NASA Technical Reports Server (NTRS)

Wisniewski, Richard J.

1957-01-01

Transition data on highly cooled blunt bodies are correlated in terms of the ratio of wall to local-stream enthalpy, Reynolds number based on displacement thickness, and location of transition. The proposed correlation, although not sensitive enough to predict the exact location of transition does predict the enthalpy ratio below which very early transition on blunt bodies is expected. The correlation is not altered by moderate amounts of surface roughness; however, the location of transition may well be affected by roughness.

Roughness of biopores and cracks in Bt-horizons by confocal laser scanning microscopy

NASA Astrophysics Data System (ADS)

Leue, Martin; Gerke, Horst H.

2016-04-01

During preferential flow events in structured soils, the movement of water and reactive solutes is mostly restricted to larger inter-aggregate pores, cracks, and biopores. The micro-topography of such macropores in terms of pore shapes, geometry, and roughness is crucial for describing the exchange of water and solutes between macropores and the soil matrix. The objective of this study was to determine the surface roughness of intact structural surfaces from the Bt-horizon of Luvisols by confocal laser scanning microscopy. For this purpose, samples with the structural surface types including cracks with and without clay-organic coatings from Bt-horizons developed on loess and glacial till were compared. The surface roughness of these structures was calculated in terms of three parameters from selected surface regions of 0.36 mm² determined with a confocal laser scanning microscope of the type Keyence VK-X100K. These data were evaluated in terms of the root-mean-squared roughness, Rq, the curvature, Rku, and the ratio between surface area and base area, RA. Values of Rq and RA were smaller for coated as compared to uncoated cracks and earthworm burrows of the Bt-horizons from both parent materials. The results indicated that the illuviation of clayey material led to a "smoothing" of the crack surfaces, which was similar for the coarser textured till-Bt and the finer-textured loess-Bt surfaces. The roughness indicated by Rq and RA values was only slightly smaller and that indicated by Rku slightly higher for the structural surfaces from the loess as compared to those from the glacial till. These results suggest a minor importance of the parent material on the roughness of structural surfaces in the Bt-horizon. The similarity of Rq, RA, and Rku values between surfaces of earthworm burrows and uncoated cracks did not confirm an expected smoothing effect of the burrow walls by the earthworm. In contrast to burrow walls, root channels from the loess-Bt were smoother than the surfaces of the other structure types, suggesting that the two types of biopores have to be distinguished when describing preferential flow and macropore-matrix exchange. Nevertheless, the confocal laser microscopy technique proved useful for characterizing the roughness of intact structural surfaces.

Immunogenicity and safety of a tetravalent E. coli O-antigen bioconjugate vaccine in animal models.

PubMed

van den Dobbelsteen, Germie P J M; Faé, Kellen C; Serroyen, Jan; van den Nieuwenhof, Ingrid M; Braun, Martin; Haeuptle, Micha A; Sirena, Dominique; Schneider, Joerg; Alaimo, Cristina; Lipowsky, Gerd; Gambillara-Fonck, Veronica; Wacker, Michael; Poolman, Jan T

2016-07-29

Extra-intestinal pathogenic Escherichia coli (ExPEC) are major human pathogens; however, no protective vaccine is currently available. We assessed in animal models the immunogenicity and safety of a 4-valent E. coli conjugate vaccine (ExPEC-4V, serotypes O1, O2, O6 and O25 conjugated to Exotoxin A from Pseudomonas aeruginosa (EPA)) produced using a novel in vivo bioconjugation method. Three doses of ExPEC-4V (with or without aluminum hydroxide) were administered to rabbits (2μg or 20μg per O-antigen, subcutaneously), mice (0.2μg or 2μg per O-antigen, subcutaneously) and rats (0.4μg or 4μg per O-antigen, intramuscularly). Antibody persistence and boostability were evaluated in rats using O6-EPA monovalent conjugate (0.4μg O-antigen/dose, intramuscularly). Toxicity was assessed in rats (16μg total polysaccharide, intramuscularly). Serum IgG and IgM antibodies were measured by ELISA. Robust antigen-specific IgG responses were observed in all animal models, with increased responses in rabbits when administered with adjuvant. O antigen-specific antibody responses persisted up to 168days post-priming. Booster immunization induced a rapid recall response. Toxicity of ExPEC-4V when administered to rats was considered to be at the no observed adverse effect level. ExPEC-4V conjugate vaccine showed good immunogenicity and tolerability in animal models supporting progression to clinical evaluation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Recognition unit-free and self-cleaning photoelectrochemical sensing platform on TiO2 nanotube photonic crystals for sensitive and selective detection of dopamine release from mouse brain.

PubMed

Xin, Yanmei; Li, Zhenzhen; Wu, Wenlong; Fu, Baihe; Wu, Hongjun; Zhang, Zhonghai

2017-01-15

For implementing sensitive and selective detection of biological molecules, the biosensors are been designed more and more complicated. The exploration of detection platform in a simple way without loss their sensitivity and selectivity is always a big challenge. Herein, a prototype of recognition biomolecule unit-free photoelectrochemical (PEC) sensing platform with self-cleaning activity is proposed with TiO 2 nanotube photonic crystal (TiO 2 NTPCs) materials as photoelectrode, and dopamine (DA) molecule as both sensitizer and target analyte. The unique adsorption between DA and TiO 2 NTPCs induces the formation of charge transfer complex, which not only expends the optical absorption of TiO 2 into visible light region, thus significantly boosts the PEC performance under illumination of visible light, but also implements the selective detection of DA on TiO 2 photoelectrode. This simple but efficient PEC analysis platform presents a low detection limit of 0.15nm for detection of DA, which allows to realize the sensitive and selective determination of DA release from the mouse brain for its practical application after coupled with a microdialysis probe. The DA functionalized TiO 2 NTPCs PEC sensing platform opens up a new PEC detection model, without using extra-biomolecule auxiliary, just with target molecule naturally adsorbed on the electrode for sensitive and selective detection, and paves a new avenue for biosensors design with minimalism idea. Copyright © 2016 Elsevier B.V. All rights reserved.

A new, easy-to-make pectin-honey hydrogel enhances wound healing in rats.

PubMed

Giusto, Gessica; Vercelli, Cristina; Comino, Francesco; Caramello, Vittorio; Tursi, Massimiliano; Gandini, Marco

2017-05-16

Honey, alone or in combination, has been used for wound healing since ancient times and has reemerged as a topic of interest in the last decade. Pectin has recently been investigated for its use in various biomedical applications such as drug delivery, skin protection, and scaffolding for cells. The aim of the present study was to develop and evaluate a pectin-honey hydrogel (PHH) as a wound healing membrane and to compare this dressing to liquid honey. Thirty-six adult male Sprague-Dawley rats were anesthetized and a 2 × 2 cm excisional wound was created on the dorsum. Animals were randomly assigned to four groups (PHH, LH, Pec, and C): in the PHH group, the pectin-honey hydrogel was applied under a bandage on the wound; in the LH group, liquid Manuka honey was applied; in the Pec group, pectin hydrogel was applied (Pec); and in the C group, only bandage was applied to the wound. Images of the wound were taken at defined time points, and the wound area reduction rate was calculated and compared between groups. The wound area reduction rate was faster in the PHH, LH, and Pec groups compared to the control group and was significantly faster in the PHH group. Surprisingly, the Pec group exhibited faster wound healing than the LH group, but this effect was not statistically significant. This is the first study using pectin in combination with honey to produce biomedical hydrogels for wound treatment. The results indicate that the use of PHH is effective for promoting and accelerating wound healing.

Using carbon nanotubes-gold nanocomposites to quench energy from pinnate titanium dioxide nanorods array for signal-on photoelectrochemical aptasensing.

PubMed

Deng, Wenping; Shen, Lei; Wang, Xiu; Yang, Chunlei; Yu, Jinghua; Yan, Mei; Song, Xianrang

2016-08-15

On the basis of the absorption and emission spectra overlap, an enhanced resonance energy transfer caused by excition-plasmon resonance between carbon nanotubes-gold nanoparticles (CNTs-Au) and pinnate titanium dioxide nanorods array (P-TiO2 NA) was obtained. Three-dimensional single crystalline P-TiO2 were prepared successfully on fluorine-doped tin oxide conducting glass (FTO glass), and its optical absorption properties and photoelectrochemical (PEC) properties were investigated. With the synergy of CNTs-Au as energy acceptor, it resulted in the enhancement of energy transfer between excited P-TiO2 NA and CNTs-Au. Upon the novel sandwichlike structure formed via DNA hybridization, the exciton produced in P-TiO2 NA was annihilated and a damped photocurrent was obtained. With the use of carcinoembryonic antigen (CEA) as a model which bonded to its specific aptamer and destroyed the sandwichlike structure, the energy transfer efficiency was lowered, leading to PEC response augment. Thus a signal-on PEC aptasensor was constructed. Under the optimal conditions, the PEC aptasensor for CEA determination exhibited a linear range from 0.001 to 2.5ngmL(-1) with a detection limit of 0.39pgmL(-1) and was satisfactory for clinical sample detection. Furthermore, the proposed aptasensor shows satisfying performance, such as easy preparation, rapid detection and so on. Moreover, since different aptamer can specifically bind to different target molecules, the designed strategy has an expansive application for the construction of versatile PEC platforms. Copyright © 2016 Elsevier B.V. All rights reserved.

Low-Cost, Efficient, and Durable H2 Production by Photoelectrochemical Water Splitting with CuGa3Se5 Photocathodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muzzillo, Christopher; Klein, Walter E; Li, Zhen

Photoelectrochemical (PEC) water splitting is an elegant method of converting sunlight and water into H2 fuel. To be commercially advantageous, PEC devices must become cheaper, more efficient, and much more durable. This work examines low-cost polycrystalline chalcopyrite films, which are successful as photovoltaic absorbers, for application as PEC absorbers. In particular, Cu-Ga-Se films with wide band gaps can be employed as top cell photocathodes in tandem devices as a realistic route to high efficiencies. In this report, we demonstrate that decreasing Cu/Ga composition from 0.66 to 0.31 in Cu-Ga-Se films increased the band gap from 1.67 to 1.86 eV andmore » decreased saturated photocurrent density from 18 to 8 mA/cm2 as measured by chopped-light current-voltage (CLIV) measurements in a 0.5 M sulfuric acid electrolyte. Buffer and catalyst surface treatments were not applied to the Cu-Ga-Se films, and they exhibited promising stability, evidenced by unchanged CLIV after 9 months of storage in air. Finally, films with Cu/Ga = 0.36 (approximately stoichiometric CuGa3Se5) and 1.86 eV band gaps had exceptional durability and continuously split water for 17 days (~12 mA/cm2 at -1 V vs RHE). This is equivalent to ~17 200 C/cm2, which is a world record for any polycrystalline PEC absorber. These results indicate that CuGa3Se5 films are prime candidates for cheaply achieving efficient and durable PEC water splitting.« less

A Practice-Oriented Bifurcation Analysis for Pulse Energy Converters: A Stability Margin

NASA Astrophysics Data System (ADS)

Kolokolov, Yury; Monovskaya, Anna

The popularity of systems of pulse energy conversion (PEC-systems) for practical applications is due to the heightened efficiency of energy conversion processes with comparatively simple realizations. Nevertheless, a PEC-system represents a nonlinear object with a variable structure, and the bifurcation analysis remains the basic tool to describe PEC dynamics evolution. The paper is devoted to the discussion on whether the scientific viewpoint on the natural nonlinear dynamics evolution can be involved in practical applications. We focus on the problems connected with stability boundaries of an operating regime. The results of both small-signal analysis and computational bifurcation analysis are considered in the parametrical space in comparison with the results of the experimental identification of the zonal heterogeneity of the operating process. This allows to propose an adapted stability margin as a sufficiently safe distance before the point after which the operating process begins to lose the stability. Such stability margin can extend the permissible operating domain in the parametrical space at the expense of using cause-and-effect relations in the context of natural regularities of nonlinear dynamics. Reasoning and discussion are based on the experimental and computational results for a synchronous buck converter with a pulse-width modulation. The presented results can be useful, first of all, for PEC-systems with significant variation of equivalent inductance and/or capacity. We believe that the discussion supports a viewpoint by which the contemporary methods of the computational and experimental bifurcation analyses possess both analytical abilities and experimental techniques for promising solutions which could be practice-oriented for PEC-systems.

Low-Cost, Efficient, and Durable H2 Production by Photoelectrochemical Water Splitting with CuGa3Se5 Photocathodes.

PubMed

Muzzillo, Christopher P; Klein, W Ellis; Li, Zhen; DeAngelis, Alexander Daniel; Horsley, Kimberly; Zhu, Kai; Gaillard, Nicolas

2018-06-13

Photoelectrochemical (PEC) water splitting is an elegant method of converting sunlight and water into H 2 fuel. To be commercially advantageous, PEC devices must become cheaper, more efficient, and much more durable. This work examines low-cost polycrystalline chalcopyrite films, which are successful as photovoltaic absorbers, for application as PEC absorbers. In particular, Cu-Ga-Se films with wide band gaps can be employed as top cell photocathodes in tandem devices as a realistic route to high efficiencies. In this report, we demonstrate that decreasing Cu/Ga composition from 0.66 to 0.31 in Cu-Ga-Se films increased the band gap from 1.67 to 1.86 eV and decreased saturated photocurrent density from 18 to 8 mA/cm 2 as measured by chopped-light current-voltage (CLIV) measurements in a 0.5 M sulfuric acid electrolyte. Buffer and catalyst surface treatments were not applied to the Cu-Ga-Se films, and they exhibited promising stability, evidenced by unchanged CLIV after 9 months of storage in air. Finally, films with Cu/Ga = 0.36 (approximately stoichiometric CuGa 3 Se 5 ) and 1.86 eV band gaps had exceptional durability and continuously split water for 17 days (∼12 mA/cm 2 at -1 V vs RHE). This is equivalent to ∼17 200 C/cm 2 , which is a world record for any polycrystalline PEC absorber. These results indicate that CuGa 3 Se 5 films are prime candidates for cheaply achieving efficient and durable PEC water splitting.

Visions of Peace Education: Interviews with the Five Former Executive Secretaries of the Peace Education Commission. Educational Information Debate 99.

ERIC Educational Resources Information Center

Bjerstedt, Ake, Ed.

The Peace Education Commission (PEC), a subgroup of the IPRA (The International Peace Research Association), was established to facilitate international cooperation among individuals interested in peace education and research related to peace education. PEC is coordinated by a Council and an Executive Secretary (at present Ake Bjerstedt). The full…

Effects of PECS Phase III Application Training on Independent Mands in Young Children with Autism

ERIC Educational Resources Information Center

Love, Jessica June

2013-01-01

The purpose of this study was to examine the effects of PECS phase III application training on independent mands in young children with autism. Participants were five children with autism ranging from ages 2 to 4 years old. A multiple baseline across participants was used to evaluate acquisition of independent correct mands across baseline and…

Quantum-size-controlled photoelectrochemical etching of semiconductor nanostructures

DOEpatents

Fischer, Arthur J.; Tsao, Jeffrey Y.; Wierer, Jr., Jonathan J.; Xiao, Xiaoyin; Wang, George T.

2016-03-01

Quantum-size-controlled photoelectrochemical (QSC-PEC) etching provides a new route to the precision fabrication of epitaxial semiconductor nanostructures in the sub-10-nm size regime. For example, quantum dots (QDs) can be QSC-PEC-etched from epitaxial InGaN thin films using narrowband laser photoexcitation, and the QD sizes (and hence bandgaps and photoluminescence wavelengths) are determined by the photoexcitation wavelength.

Effects of Iconicity on Requesting with the Picture Exchange Communication System in Children with Autism Spectrum Disorder

ERIC Educational Resources Information Center

Angermeier, Katie; Schlosser, Ralf W.; Luiselli, James K.; Harrington, Caroline; Carter, Beth

2008-01-01

Research on graphic symbol learning suggests that symbols with a greater visual resemblance to their referents (greater iconicity) are more easily learned. The iconicity hypothesis has not yet been explored within the intervention protocol of the Picture Exchange Communication System (PECS). Within the PECS protocol, participants do not point to a…

The Application of PECS in a Deaf Child with Autism: A Case Study

ERIC Educational Resources Information Center

Malandraki, Georgia A.; Okalidou, Areti

2007-01-01

A 10-year-old nonverbal Greek boy, C.Z., who had been diagnosed with both bilateral sensorineural profound hearing loss and autism, was taught to use the Picture Exchange Communication System (PECS), with some modifications and extensions, over a 4-month intensive intervention period. C.Z.'s original communication and behavioral status as well as…

Effects of the Picture Exchange Communication System (PECS) on Maladaptive Behavior in Children with Autism Spectrum Disorders (ASD): A Review of the Literature

ERIC Educational Resources Information Center

Battaglia, Dana; McDonald, Mary E.

2015-01-01

This paper provides an overview of the literature investigating the functional relationship between the use of the Picture Exchange Communication System (PECS) and maladaptive behavior (i.e., aggression, tantrums) in individuals with autism spectrum disorders (ASD). Digital searches were conducted to identify single subject design studies…

The Picture Exchange Communication System: Effects on Manding and Speech Development for School-Aged Children with Autism

ERIC Educational Resources Information Center

Tincani, Matt; Crozier, Shannon; Alazett, Shannon

2006-01-01

We examined the effects of the Picture Exchange Communication System (PECS; Frost & Bondy, 2002) on the manding (requesting) and speech development of school-aged children with autism. In study 1, two participants, Damian and Bob, were taught PECS within a delayed multiple baseline design. Both participants demonstrated increased levels of manding…

The Effectiveness of Combining Tangible Symbols with the Picture Exchange Communication System to Teach Requesting Skills to Children with Multiple Disabilities Including Visual Impairment

ERIC Educational Resources Information Center

Ali, Emad

2009-01-01

The Picture Exchange Communication System (PECS) is an augmentative and alternative communication program (Frost & Bondy, 2002). Although PECS has been effectively used to teach functional requesting skills for children with autism, mental retardation, visual impairment, and physical disabilities (e.g., Anderson, Moore, & Bourne, 2007; Chambers &…