Characterization of the aroma profile of novel Brazilian wines by solid-phase microextraction using polymeric ionic liquid sorbent coatings.

PubMed

Crucello, Juliana; Miron, Luiz F O; Ferreira, Victor H C; Nan, He; Marques, Marcia O M; Ritschel, Patricia S; Zanus, Mauro C; Anderson, Jared L; Poppi, Ronei J; Hantao, Leandro W

2018-05-28

In this study, a series of polymeric ionic liquid (PIL) sorbent coatings is evaluated for the extraction of polar volatile organic compounds (VOCs) from Brazilian wines using headspace solid-phase microextraction (HS-SPME), including samples from 'Isabella' and 'BRS Magna' cultivars-the latter was recently introduced by the Brazilian Agricultural Research Corporation - National Grape & Wine Research Center. The structurally tuned SPME coatings were compared to the commercial SPME phases, namely poly(acrylate) (PA) and divinylbenzene/carboxen/poly(dimethylsiloxane) (DVB/CAR/PDMS). The separation, detection and identification of the aroma profiles were obtained using comprehensive two-dimensional gas chromatography mass spectrometry (GC×GC-MS). The best performing PIL-based SPME fiber, namely 1-hexadecyl-3-vinylimidazolium bis[(trifluoromethyl)sulfonyl]imide with 1,12-di(3-vinylimidazolium)dodecane dibis[(trifluoromethyl)sulfonyl]imide incorporated cross-linker supported on an elastic nitinol wire, exhibited superior performance to DVB/CAR/PDMS regarding the average number of extracted peaks and extracted more polar analytes providing additional insight into the aroma profile of 'BRS Magna' wines. Four batches of wine were evaluated, namely 'Isabella' and 'BRS Magna' vintages 2015 and 2016, using highly selective PIL-based SPME coatings and enabled the detection of 350+ peaks. Furthermore, this is the first report evaluating the aroma of 'BRS Magna' wines. A hybrid approach that combined pixel-based Fisher ratio and peak table-based data comparison was used for data handling. This proof-of-concept experiment provided reliable and statistically valid distinction of wines that may guide regulation agencies to create high sample throughput protocols to screen wines exported by Brazilian vintners. Graphical abstract Highly selective extraction of wine aroma using polymeric ionic liquid.

Use of ionic liquids as headspace gas chromatography diluents for the analysis of residual solvents in pharmaceuticals.

PubMed

Nacham, Omprakash; Ho, Tien D; Anderson, Jared L; Webster, Gregory K

2017-10-25

In this study, two ionic liquids (ILs), 1-butyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide ([BMIM][NTf 2 ]) and trihexyltetradecylphosphonium bis[(trifluoromethyl)sulfonyl]imide ([P 66614 ][NTf 2 ]) were examined as contemporary diluents for residual solvent analysis using static headspace gas chromatography (SHS-GC) coupled with flame ionization detection (FID). ILs are a class of non-molecular solvents featuring negligible vapor pressure and high thermal stabilities. Owing to these favorable properties, ILs have potential to enable superior sensitivity and reduced interference, compared to conventional organic diluents, at high headspace incubation temperatures. By employing the [BMIM][NTf 2 ] IL as a diluent, a 25-fold improvement in limit of detection (LOD) was observed with respect to traditional HS-GC diluents, such as N-methylpyrrolidone (NMP). The established IL-based method demonstrated LODs ranging from 5.8 parts-per-million (ppm) to 20ppm of residual solvents in drug substances. The optimization of headspace extraction conditions was performed prior to method validation. An incubation temperature of 140°C and a 15min incubation time provided the best sensitivity for the analysis. Under optimized experimental conditions, the mass of residual solvents partitioned in the headspace was higher when using [BMIM][NTf 2 ] than NMP as a diluent. The analytical performance was demonstrated by determining the repeatability, accuracy, and linearity of the method. Linear ranges of up to two orders of magnitude were obtained for class 3 solvents. Excellent analyte recoveries were obtained in the presence of three different active pharmaceutical ingredients. Owing to its robustness, high throughput, and superior sensitivity, the HS-GC IL-based method can be used as an alternative to existing residual solvent methods. Copyright © 2017 Elsevier B.V. All rights reserved.

Expanding the use of polymeric ionic liquids in headspace solid-phase microextraction: Determination of ultraviolet filters in water samples.

PubMed

Trujillo-Rodríguez, María J; Nan, He; Anderson, Jared L

2018-03-09

Three crosslinked polymeric ionic liquid (PIL) sorbent coatings were used in headspace solid-phase microextraction for the determination of a group of ultraviolet filters. The developed crosslinked PIL-based materials include two polycations and a double confined PIL. The method, in combination with gas chromatography-mass spectrometry, is simple, solvent free, and does not require of any derivatization step. After proper optimization of the methodologies with each developed fiber, the analytical performance was compared with a commercial polyacrylate fiber. A study of the normalized calibration slopes, obtained by dividing the calibration slope of each analyte by the coating volume, revealed that the crosslinked fibers can be used as alternatives to commercial fibers for the determination of the selected group of compounds. In particular, the coating nature of the PIL containing the 1-vinylbenzyl-3-hexadecylimidazolium bis[(trifluoromethyl)sulfonyl]imide IL as monomer and the 1,12-di(3-vinylbenzylimidazolium)dodecane bis[(trifluoromethyl)sulfonyl]imide IL as crosslinker is the most suitable for the extraction of the selected compounds despite their coating volume, being 3.6 times lower than the commercial polyacrylate fiber. For this fiber, wide linear ranges, correlation coefficients higher than 0.990, limits of detection ranging from 2.8 ng L -1 to 26 ng L -1 and relative standard deviations ranging from 2.5 to 15% were achieved. Finally, all proposed PIL-based fibers were applied towards the analysis of tap water, pool water and lake water, with the majority of the ultraviolet filters being detected and quantified in the last two types of samples. Copyright © 2018 Elsevier B.V. All rights reserved.

Self-Supporting, Hydrophobic, Ionic Liquid-Based Reference Electrodes Prepared by Polymerization-Induced Microphase Separation.

PubMed

Chopade, Sujay A; Anderson, Evan L; Schmidt, Peter W; Lodge, Timothy P; Hillmyer, Marc A; Bühlmann, Philippe

2017-10-27

Interfaces of ionic liquids and aqueous solutions exhibit stable electrical potentials over a wide range of aqueous electrolyte concentrations. This makes ionic liquids suitable as bridge materials that separate in electroanalytical measurements the reference electrode from samples with low and/or unknown ionic strengths. However, methods for the preparation of ionic liquid-based reference electrodes have not been explored widely. We have designed a convenient and reliable synthesis of ionic liquid-based reference electrodes by polymerization-induced microphase separation. This technique allows for a facile, single-pot synthesis of ready-to-use reference electrodes that incorporate ion conducting nanochannels filled with either 1-octyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide or 1-dodecyl-3-methylimidazolium bis(trifluoromethyl sulfonyl)imide as ionic liquid, supported by a mechanically robust cross-linked polystyrene phase. This synthesis procedure allows for the straightforward design of various reference electrode geometries. These reference electrodes exhibit a low resistance as well as good reference potential stability and reproducibility when immersed into aqueous solutions varying from deionized, purified water to 100 mM KCl, while requiring no correction for liquid junction potentials.

Characterization of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([Emim][Tf2N])∕TX-100∕cyclohexane ternary microemulsion: investigation of photoinduced electron transfer in this RTIL containing microemulsion.

PubMed

Sarkar, Souravi; Pramanik, Rajib; Ghatak, Chiranjib; Rao, Vishal Govind; Sarkar, Nilmoni

2011-02-21

In this study we have characterized a ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethyl- sulfonyl)imide containing ternary nonaqueous microemulsion ([Emim][Tf(2)N]∕∕TX-100∕cyclo- hexane). The phase behavior and dynamic light scattering study show that the [Emim][Tf(2)N]∕TX-100∕cyclohexane three component system can form microemulsion with [Emim][Tf(2)N] as polar core at suitable condition. We have investigated photoinduced electron transfer (PET) using dimethyl aniline as electron donor and several Coumarin dyes as electron acceptor molecules at two different R values (R = [ionic liquid]∕[surfactant]) to observe how the dynamics of the PET rate is affected in this type of confined microenvironment compared to that of the PET dynamics in neat ionic liquid and other pure solvent media. The plot of observed k(q) values with the free energy change (ΔG(0)) for electron transfer reaction shows an apparent inversion in the observed rate as predicted by the Marcus theory.

Role of solvents on the oxygen reduction and evolution of rechargeable Li-O2 battery

NASA Astrophysics Data System (ADS)

Christy, Maria; Arul, Anupriya; Zahoor, Awan; Moon, Kwang Uk; Oh, Mi Young; Stephan, A. Manuel; Nahm, Kee Suk

2017-02-01

The choice of electrolyte solvent is expected to play a key role in influencing the lithium-oxygen battery performance. The electrochemical performances of three electrolytes composed of lithium bis (trifluoromethane sulfonyl) imide (LiTFSI) salt and different solvents namely, ethylene carbonate/propylene carbonate (EC/PC), tetra ethylene glycol dimethyl ether (TEGDME) and dimethyl sulfoxide (DMSO) are investigated by assembling lithium oxygen cells. The electrolyte composition significantly varied the specific capacity of the battery. The choice of electrolyte also influences the overpotential, cycle life, and rechargeability of the battery. Electrochemical impedance spectra, cyclic voltammetry, and chronoamperometry were utilized to determine the reversible reactions associated with the air cathode.

Thermophysical properties of tri-n-butylphosphate-ionic liquid mixture

NASA Astrophysics Data System (ADS)

Rout, Alok; Mishra, Satyabrata; Venkatesan, K. A.; Antony, M. P.; Pandey, N. K.

2018-04-01

Thermophysical properties such as viscosity, density, energy of activation and coefficient of thermal expansion were measured for the solvent phase composed of tri-n-butylphosphate (TBP), 1-butyl-3-methylimidazolium bis(trifluoromethane-sulfonyl)imide ([C4mim][NTf2]) and 1.1 M TBP/[C4mim][NTf2]. The results were compared with that of nitric acid equilibrated [C4mim][NTf2] and 1.1M TBP/[C4mim][NTf2]. Thermal stability of the ionic liquid phase was assessed by using differential scanning calorimetric (DSC) technique. Other important physical properties such as refractive index and surface tension of the ionic liquid phase composition were evaluated before and after acid saturation.

Enhancing thermoelectrochemical properties by tethering ferrocene to the anion or cation of ionic liquids: altered thermodynamics and solubility.

PubMed

Aldous, Leigh; Black, Jeffrey J; Elias, Maximo C; Gélinas, Bruno; Rochefort, Dominic

2017-09-13

Entropic changes inherent within a redox process typically result in significant temperature sensitivity. This can be utilised positively or can be a detrimental process. This study has investigated the thermoelectrochemical properties (temperature-dependant electrochemistry) of the ferrocenium|ferrocene redox couple in an ionic liquid, and in particular the effect of covalently tethering this redox couple to fixed positive or negative charges. As such, the ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide was employed to dissolve ferrocene, as well as cationic-tethered ferrocene (the 1-ethyl-3-(methylferrocenyl)imidazolium cation) and anionic-tethered ferrocene (the ferrocenylsulfonyl(trifluoromethylsulfonyl)imide anion). These systems were characterised in terms of their voltammetry (apparent formal potentials, diffusion coefficients and electron transfer rate constants) and thermoelectrochemistry (temperature coefficients of the cell potential or 'Seebeck coefficients', short circuit current densities and power density outputs). The oxidised cationic species behaved like a dicationic species and was thus 6-fold more effective at converting waste thermal energy to electrical power within a thermoelectrochemical cell than unmodified ferrocene. This was almost exclusively due to a significant boost in the Seebeck coefficient of this redox couple. Conversely, the oxidised anionic species was formally a zwitterion, but this zwitterionic species behaved thermodynamically like a neutral species. The inverted entropic change upon going from ferrocene to anion-tethered ferrocene allowed development of a largely temperature-insensitive reference potential based upon a mixture of acetylferrocene and ferricenyl(iii)sulfonyl(trifluoromethylsulfonyl)imide.

Self-Supporting, Hydrophobic, Ionic Liquid-Based Reference Electrodes Prepared by Polymerization-Induced Microphase Separation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chopade, Sujay A.; Anderson, Evan L.; Schmidt, Peter W.

Interfaces of ionic liquids and aqueous solutions exhibit stable electrical potentials over a wide range of aqueous electrolyte concentrations. This makes ionic liquids suitable as bridge materials that separate in electroanalytical measurements the reference electrode from samples with low and/or unknown ionic strengths. However, methods for the preparation of ionic liquid-based reference electrodes have not been explored widely. We have designed a convenient and reliable synthesis of ionic liquid-based reference electrodes by polymerization-induced microphase separation. This technique allows for a facile, single-pot synthesis of ready-to-use reference electrodes that incorporate ion conducting nanochannels filled with either 1-octyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide or 1-dodecyl-3-methylimidazolium bis(trifluoromethylmore » sulfonyl)imide as ionic liquid, supported by a mechanically robust cross-linked polystyrene phase. This synthesis procedure allows for the straightforward design of various reference electrode geometries. These reference electrodes exhibit a low resistance as well as good reference potential stability and reproducibility when immersed into aqueous solutions varying from deionized, purified water to 100 mM KCl, while requiring no correction for liquid junction potentials.« less

Nanoscale organization in the fluorinated room temperature ionic liquid: Tetraethyl ammonium (trifluoromethanesulfonyl)(nonafluorobutylsulfonyl)imide

NASA Astrophysics Data System (ADS)

Lo Celso, F.; Appetecchi, G. B.; Jafta, C. J.; Gontrani, L.; Canongia Lopes, J. N.; Triolo, A.; Russina, O.

2018-05-01

Fluorinated Room Temperature Ionic Liquids (FRTILs) are a branch of ionic liquids that is the object of growing interest for a wide range of potential applications, due to the synergic combination of specifically ionic features and those properties that stem from fluorous tails. So far limited experimental work exists on the micro- and mesoscopic structural organization in this class of compounds. Such a work is however necessary to fully understand morphological details at atomistic level that would have strong implications in terms of bulk properties. Here we use the synergy between X-ray and neutron scattering together with molecular dynamics simulations to access structural details of a technologically relevant FRTIL that is characterised by an anion bearing a long enough fluorinated tail to develop specific morphological features. In particular, we find the first experimental evidence that in FRTILs bearing an asymmetric bis(perfluoroalkyl)sulfonyl-imide anion, fluorous side chains tend to be spatially segregated into nm-scale spatial heterogeneities. This feature together with the well-established micro-segregation of side alkyl chains in conventional RTILs leads to the concept of triphilic ILs, whose technological applications are yet to be fully developed.

A solid state actuator based on polypyrrole (PPy) and a solid electrolyte NBR working in air

NASA Astrophysics Data System (ADS)

Cho, Misuk; Nam, Jaedo; Choi, Hyouk Ryeol; Koo, Jachoon; Lee, Youngkwan

2005-05-01

The solid polymer electrolyte based conducting polymer actuator was presented. In the preparation of acutuator module, an ionic liquid impregnated a synthetic rubber (NBR) and PPy were used as a solid polymer electrolyte and conducting polymer, respectively. An ionic liquid, 1-butyl-3-methylimidazolium bis (trifluoromethyl sulfonyl)imide (BMITFSI) is gradually dispersed into the NBR film and the conducting polymer, PPy was synthesized on the surface of NBR. The ionic conductivity of new type solid polymer electrolyte as a function of the immersion time was investigated. The cyclic voltammetry responsed and the redox switching dynamics of PEDOT in NBR matrix were studied. The displacement of the actuator was measured by laser beam.

Cs[Tf 2N]: a second polymorph with a layered structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stritzinger, Jared Tyler; Droessler, Janelle E.; Scott, Brian Lindley

Here, the structural determination of the ionic liquid, caesium bis­[(tri­fluoro­meth­yl)sulfon­yl]imide or poly[[ μ4-bis­[(tri­fluoro­meth­yl)sulfon­yl]imido]caesium(I)], Cs[N(SO 2CF 3) 2] or Cs[Tf 2N], reveals a second polymorph that also crystallizes in a layer structure possessing monoclinic P2 1/c symmetry at 120 K instead of C2/c for the known polymorph. The caesium ions in the cationic layers are coordinated by the sulfonyl groups of the bis­triflimide mol­ecules from anion layers while the tri­fluoro­methyl groups are oriented in the opposite direction, forming a non-polar surface separating the layers.

Cs[Tf 2N]: a second polymorph with a layered structure

DOE PAGES

Stritzinger, Jared Tyler; Droessler, Janelle E.; Scott, Brian Lindley; ...

2018-03-23

Here, the structural determination of the ionic liquid, caesium bis­[(tri­fluoro­meth­yl)sulfon­yl]imide or poly[[ μ4-bis­[(tri­fluoro­meth­yl)sulfon­yl]imido]caesium(I)], Cs[N(SO 2CF 3) 2] or Cs[Tf 2N], reveals a second polymorph that also crystallizes in a layer structure possessing monoclinic P2 1/c symmetry at 120 K instead of C2/c for the known polymorph. The caesium ions in the cationic layers are coordinated by the sulfonyl groups of the bis­triflimide mol­ecules from anion layers while the tri­fluoro­methyl groups are oriented in the opposite direction, forming a non-polar surface separating the layers.

Hepatic Metabolism of Perfluorinated Carboxylic Acids: A Nuclear Magnetic Resonance Investigation

DTIC Science & Technology

1990-12-14

perfluoro -n- octanoic acid ( PFOA ) and perfluoro -n-decanoic acid ( PFDA ) In the rat. Spectra obtained at various times following the administration of PFOA ...used to monitor the metabolic fate of perfluoro -n-octanoic acid ( PFOA ) and perfluoro -n-decanoic acid ( PFDA ) in the rat. Spectra obtained at various...specifically Investigate the metabolic effects caused by perfluoro -n-octanoic acid ( PFOA ) and perfluoro -n-decanoic acid ( PFDA ) in rats.

Environmentally-friendly lithium recycling from a spent organic li-ion battery.

PubMed

Renault, Stéven; Brandell, Daniel; Edström, Kristina

2014-10-01

A simple and straightforward method using non-polluting solvents and a single thermal treatment step at moderate temperature was investigated as an environmentally-friendly process to recycle lithium from organic electrode materials for secondary lithium batteries. This method, highly dependent on the choice of electrolyte, gives up to 99% of sustained capacity for the recycled materials used in a second life-cycle battery when compared with the original. The best results were obtained using a dimethyl carbonate/lithium bis(trifluoromethane sulfonyl) imide electrolyte that does not decompose in presence of water. The process implies a thermal decomposition step at a moderate temperature of the extracted organic material into lithium carbonate, which is then used as a lithiation agent for the preparation of fresh electrode material without loss of lithium. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Osmotic Heat Engine Using Thermally Responsive Ionic Liquids.

PubMed

Zhong, Yujiang; Wang, Xinbo; Feng, Xiaoshuang; Telalovic, Selvedin; Gnanou, Yves; Huang, Kuo-Wei; Hu, Xiao; Lai, Zhiping

2017-08-15

The osmotic heat engine (OHE) is a promising technology for converting low grade heat to electricity. Most of the existing studies have focused on thermolytic salt systems. Herein, for the first time, we proposed to use thermally responsive ionic liquids (TRIL) that have either an upper critical solution temperature (UCST) or lower critical solution temperature (LCST) type of phase behavior as novel thermolytic osmotic agents. Closed-loop TRIL-OHEs were designed based on these unique phase behaviors to convert low grade heat to work or electricity. Experimental studies using two UCST-type TRILs, protonated betaine bis(trifluoromethyl sulfonyl)imide ([Hbet][Tf 2 N]) and choline bis(trifluoromethylsulfonyl)imide ([choline][Tf 2 N]) showed that (1) the specific energy of the TRIL-OHE system could reach as high as 4.0 times that of the seawater and river water system, (2) the power density measured from a commercial FO membrane reached up to 2.3 W/m 2 , and (3) the overall energy efficiency reached up to 2.6% or 18% of the Carnot efficiency at no heat recovery and up to 10.5% or 71% of the Carnet efficiency at 70% heat recovery. All of these results clearly demonstrated the great potential of using TRILs as novel osmotic agents to design high efficient OHEs for recovery of low grade thermal energy to work or electricity.

Phase Equilibrium Investigation on 2-Phenylethanol in Binary and Ternary Systems: Influence of High Pressure on Density and Solid-Liquid Phase Equilibrium.

PubMed

Domańska, Urszula; Królikowski, Marek; Wlazło, Michał; Więckowski, Mikołaj

2018-05-30

Ionic liquids (ILs) are important new solvents proposed for applications in different separation processes. Herein, an idea of possible use of high pressure in a general strategy of production of 2-phenylethanol (PEA) is discussed. In this work, we present the influence of pressure on the density in binary systems of {1-hexyl-1-methylpyrrolidynium bis{(trifluoromethyl)sulfonyl}imide, [HMPYR][NTf 2 ], or 1-dodecyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}imide, [DoMIM][NTf 2 ] + PEA} in a wide range of temperatures (298.15-348.15 K) and pressures (0.1-40 MPa). The densities at ambient and high pressures are measured to present the physicochemical properties of the ILs used in the process of separation of PEA from aqueous phase. The Tait equation was used for the correlation of density of one-component and two-component systems as a function of mole fraction, temperature, and pressure. The influence of pressure is not significant. These systems exhibit mainly negative molar excess volumes, V E . The solid-liquid phase equilibrium (SLE) of [DoMIM][NTf 2 ] in PEA at atmospheric pressure was measured and compared to the SLE high-pressure results. Additionally, the ternary liquid-liquid phase equilibrium (LLE) at ambient pressure in the {[DoMIM][NTf 2 ] (1) + PEA (2) + water (3)} at temperature T = 308.15 K was investigated. The solubility of water in the [DoMIM][NTf 2 ] is quite high in comparison with that measured by us earlier for ILs ( x 3 = 0.403) at T = 308.15 K, which results in not very successful average selectivity of extraction of PEA from the aqueous phase. The [DoMIM][NTf 2 ] has shown strong interaction with PEA without the immiscibility region. The ternary system revealed Treybal's type phase equilibrium in which two partially miscible binaries ([DoMIM][NTf 2 ] + water) and (PEA + water) exist. From the results of LLE in the ternary system, the selectivity and the solute distribution ratio of separation of water/PEA were calculated and compared to the results obtained for the ILs measured earlier by us. The popular NRTL model was used to correlate the experimental tie-lines in ternary LLE. These results may help in a new technological project of "in situ" extraction of PEA from aqueous phase during the biosynthesis.

Genotoxicity Assessment of Perfluorodecanoic Acid Using a Battery of In Vitro and In Vivo/in Vitro Assays.

DTIC Science & Technology

1990-12-01

Maximum 200 words) Perfluoro -n-decanoic acid ( PFDA ), a perfluorinated fatty acid was evaluated in in vitro bioassays to assess its potential...PolychlorotrifluoroethyleneDU.TBL PFDA Perfluoro -n-decanoic acid PFOA Perfluoro -n-octanoic acid ..... RI Replicative index rpm Revolutions per minute By...an increase in the amount of S-phase DNA synthesis. The perfluorinated carboxylic acid, perfluoro -n-decanoic acid ( PFDA ), has previously been shown to

Comparison of PFDA (Perfluoro-n-Decanoic Acid) and TCDD on Heart Membranes.

DTIC Science & Technology

1986-06-18

AD-A171 960 COMPARISON OF PFDA ( PERFLUORO -N-DECANOIC ACID) AND TCDD 1/1 ON HEART NEMBRANES(U) WRIGHT STATE UNIY DAYTON OH SCHOOL OF MEDICINE A E...1986) Toxicol. Appl. Pharmacol. Perfluoro -n-decanoic acid ( PFDA ) is a synthetic chemical resembling a 10 carbon fatty acid. Several studies have...3 INTRODUCTION Perfluoro -n-decanoic acid ( PFDA ; nonadecafluorodecanoic acid, C10 F19 0 2H) is a straight-chain 10 carbon carboxylic acid with fluorine

Structure and dynamics of mica-confined films of [C10C1Pyrr][NTf2] ionic liquid

NASA Astrophysics Data System (ADS)

Freitas, Adilson Alves de; Shimizu, Karina; Smith, Alexander M.; Perkin, Susan; Canongia Lopes, José Nuno

2018-05-01

The structure of the ionic liquid 1-decyl-1-methylpyrrolidinium bis[(trifluoromethane)sulfonyl]imide, [C10C1Pyrr][NTf2], has been probed using Molecular Dynamics (MD) simulations. The simulations endeavour to model the behaviour of the ionic liquid in bulk isotropic conditions and also at interfaces and in confinement. The MD results have been confronted and validated with scattering and surface force experiments reported in the literature. The calculated structure factors, distribution functions, and density profiles were able to provide molecular and mechanistic insights into the properties of these long chain ionic liquids under different conditions, in particular those that lead to the formation of multi-layered ionic liquid films in confinement. Other properties inaccessible to experiment such as in-plane structures and relaxation rates within the films have also been analysed. Overall the work contributes structural and dynamic information relevant to many applications of ionic liquids with long alkyl chains, ranging from nanoparticle synthesis to lubrication.

Vaporisation of an ionic liquid near room temperature.

PubMed

Lovelock, Kevin R J; Deyko, Alexey; Licence, Peter; Jones, Robert G

2010-08-21

The temperature at which the vapour phase of the ionic liquids (ILs) 1-ethyl-3-methylimidazolium bis[(trifluoromethane)sulfonyl]imide, [C(2)C(1)Im][Tf(2)N], and 1-ethyl-3-methylimidazolium ethylsulfate, [C(2)C(1)Im][EtOSO(3)], can be detected was investigated using line-of-sight mass spectrometry (LOSMS). By optimising the detection system used in previous experiments, the lowest temperature for which vapour was detected for [C(2)C(1)Im][Tf(2)N] was approximately 340 K, whereas for [C(2)C(1)Im][EtOSO(3)] it was approximately 390 K. Initial investigations also show that the temperature at which measurements are made affects the enthalpy of vaporisation at 298 K, Delta(vap)H(298). The reasons for these differences in Delta(vap)H(298) with respect to temperature are discussed. The vapour pressure of both ILs is estimated at far lower temperatures than previously achieved and extrapolations to room temperature are given.

Syntheses and degradations of fluorinated heterocyclics

NASA Technical Reports Server (NTRS)

Paciorek, K. L.; Kratzer, R. H.; Kaufman, J.; Rosser, R. W.

1975-01-01

The relative stability of two ring systems, the triazine rings and 1,2,4-oxadiazoles, which offer potential crosslinks useful for curing perfluoroalkyl ether elastomers, has been investigated. Tris (perfluoro-n-heptyl)-s-triazine, the perfluoroether substituted-s-triazine, 1,4-bis/(5-perfluoro-n-heptyl)-1,2,4-oxadiazolyl/benzene, its perfluoroalkyl ether substituted analog, and 3,5-bis-(perfluoro-n-heptyl)-1,2,4-oxadiazole were synthesized and subjected to thermal and oxidative degradation at 235 and 325 C and to hydrolytic degradation at 235 C. The perfluoroalkyl ether substituted triazine and 3,5-bis(perfluoro-n-heptyl)-1,2,4-oxadiazole were found to be stable under all conditions investigated.

1-Bromoethene-1-sulfonyl fluoride (BESF) is another good connective hub for SuFEx click chemistry.

PubMed

Smedley, Christopher J; Giel, Marie-Claire; Molino, Andrew; Barrow, Andrew S; Wilson, David J D; Moses, John E

2018-05-25

We demonstrate 1,2-dibromoethane-1-sulfonyl fluoride (DESF) as a bench-stable and readily accessible precursor to the robust SuFEx connector, 1-bromoethene-1-sulfonyl fluoride (BESF). The in situ generation of BESF from DESF opens up several new reaction profiles, including application in the syntheses of unprecedented 3-substituted isoxazole-5-sulfonyl fluorides, 1-substituted-1H-1,2,3-triazole-4-sulfonyl fluorides, 2-amino-1-bromoethane-1-sulfonyl fluorides and 4-bromo-β-sultams in good to excellent yields. These new modules comprise a pendant sulfonyl fluoride handle, which further undergoes facile and selective SuFEx reactions with a selection of aryl silyl ethers to generate stable and useful sulfonate connections.

Hepatic Toxicity of Perfluorocarboxylic Acids.

DTIC Science & Technology

1996-07-01

1995). 3. N. V. Reo, C. M. Goecke, L. Narayanan, and B. M. Jarnot. "Effects of Perfluoro-n-octanoic Acid , Perfluoro-n-decanoic Acid , and Clofibrate ...Artz, and B. M. Jarnot: "ILiver Phosphorous Metabolic Response to Perfluorocarboxylic Acids and Clofibrate in Rats and Guinea Pigs: A 31 P NMR Study...Peroxisome Induction by Perfluoro-n-decanoic Acid and Clofibrate in the Rat: Proliferation Versus Activity." International Society for the Study of

40 CFR 721.5286 - Benzenediazonium, [[[[(substituted) azo]phenyl]sulfonyl]amino]-, coupled with aminophenol...

Code of Federal Regulations, 2010 CFR

2010-07-01

...) azo]phenyl]sulfonyl]amino]-, coupled with aminophenol, diazotized aminobenzoic acid, diazotized..., [[[[(substituted) azo]phenyl]sulfonyl]amino]-, coupled with aminophenol, diazotized aminobenzoic acid, diazotized..., [[[[(substituted)azo]phenyl]sulfonyl]amino]-, coupled with aminophenol, diazotized aminobenzoic acid, diazotized...

40 CFR 721.5286 - Benzenediazonium, [[[[(substituted) azo]phenyl]sulfonyl]amino]-, coupled with aminophenol...

Code of Federal Regulations, 2011 CFR

2011-07-01

...) azo]phenyl]sulfonyl]amino]-, coupled with aminophenol, diazotized aminobenzoic acid, diazotized..., [[[[(substituted) azo]phenyl]sulfonyl]amino]-, coupled with aminophenol, diazotized aminobenzoic acid, diazotized..., [[[[(substituted)azo]phenyl]sulfonyl]amino]-, coupled with aminophenol, diazotized aminobenzoic acid, diazotized...

Hepatic Metabolism of Perfluorinated Carboxylic Acids: A Nuclear Magnetic Resonance Investigation in Vivo

DTIC Science & Technology

1995-01-17

perfluorocarboxylic acids and the hepatotoxicity associated with perfluoro -n-octanoic acid ( PFOA ) and perfluoro -n-decanoic acid ( PFDA ). Newly proposed...octanoic acid ( PFOA ) and perfluoro -n-decanoic acid ( PFDA ). These Air Force chemicals belong to a class of CU’. compounds known as peroxisome...dose. These data indicate that the C9 and C 11 perfluorocarboxylic acids are peroxisome proliferators, similar to PFOA and PFDA . Figure 4 shows the

Crosslinking and degradation mechanisms in model sealant candidates

NASA Technical Reports Server (NTRS)

Paciorek, K. L.; Kaufman, J.; Kratzer, R. H.

1974-01-01

Heterocyclic ring systems were investigated, triazines and 1,2,4-oxadiazoles. Only a limited effort was extended to the preparation of triazoles. Compounds, n-perfluoroheptyl-s-triazine, a perfluoroether substituted triazine, C3F7OCF(CF3)CF2OCF(CF3) 3C3N3,1,4-bus (5-perfluoro-n-heptyl)-1,2,4-oxadiazolyl -benzene, its perfluoroalkylether substituded analogue, and 3,5-bis(perfluoro-n-heptyl)-1,2,4-oxadiazole were synthesized and characterized. To eliminate the effect due to a tertiary fluorine present in branched materials, the pure n-alkyl-compounds were prepared. The main starting material, perfluoro-n-octanonitrile, was obtained from commercially available perfluoro-n-octanoic acid via a three step synthesis.

X-ray investigations of sulfur-containing fungicides. IV. 4'-[[Benzoyl(4-chlorophenylhydrazono)methyl]sulfonyl]acetanilide and 4'-[[benzoyl(4-methoxyphenylhydrazono)methyl]sulfonyl]acetanilide.

PubMed

Wolf, W M

2001-09-01

The conformations of the two approximately isomorphous structures 4'-[[benzoyl(4-chlorophenylhydrazono)methyl]sulfonyl]acetanilide, C(22)H(18)ClN(3)O(4)S, and 4'-[[benzoyl(4-methoxyphenylhydrazono)methyl]sulfonyl]acetanilide, C(23)H(21)N(3)O(5)S, are stabilized by resonance-assisted intramolecular hydrogen bonds linking the hydrazone moieties and sulfonyl groups. The stronger bond is observed in the former compound. The difference in electronic properties between the Cl atom and the methoxy group is too small to significantly alter the non-bonding interactions of the sulfonyl and beta-carbonyl groups.

Durable Fluorocarbon-Based Coatings for Aircraft

DTIC Science & Technology

2000-11-01

synthesized two novel monomers, 2-fluoro-2- perfluorooctyl - 1,3-propanediol and 2-fluoro-2- perfluoro (2-ethylhexyl)-1,3-propanediol, and demonstrated that...propanediols, two branched perfluoroalkyl methanols, perfluoro -1H,1H-2-ethylhexanol (pefluoro-1-ethylpentyl methanol) and perfluoro - 1H,1H-2,2...malonates. Reduction of the perfluorinated malonates gave the perfluoroalkyl -branched 1,3-propanediols. R-OH + HBr R-Br cat. O O OCH 2CH3 OCH 2CH3 + O O

Electrical and structural studies of polymer electrolyte based on chitosan/methyl cellulose blend doped with BMIMTFSI

NASA Astrophysics Data System (ADS)

Misenan, M. S. M.; Isa, M. I. N.; Khiar, A. S. A.

2018-05-01

In this study, blended polymer electrolyte of methylcellulose (MC)/chitosan (CS) was prepared with different weight percentage of 1-butyl-3-methylimidazolium bis(trifluoromethyl sulfonyl) imide (BMIMTFSI) which acts as ion donor. This polymer blend was prepared by solution casting technique. The micro structure was observed by Field Emission Scanning Electron Microscopy (FESEM) where the multilayer could possibly be ascribed to the limited chain mobility. Sample having 60 wt% CS: 40 wt% MC was determined to have the most amorphous morphology extracted using deconvoluted data from x-ray Diffractography (XRD). Fourier Transform Infrared Spectroscopy (FTIR) peaks analysis shows the significant shift indicates complexation between ionic liquid and polymer backbone. The film was also characterized by impedance spectroscopy to measure its ionic conductivity. Samples with 45% of BMITFSI exhibit the highest conductivity of (1.51 ± 0.13) × 10‑6 S cm‑1 at ambient. Conductivity at elevated temperature was also studied, and the electrolytes obeys the Arrhenius behaviour. The conduction mechanism was best presented by small polaron hopping model.

Design of Phosphonium-Type Zwitterion as an Additive to Improve Saturated Water Content of Phase-Separated Ionic Liquid from Aqueous Phase toward Reversible Extraction of Proteins

PubMed Central

Ito, Yoritsugu; Kohno, Yuki; Nakamura, Nobuhumi; Ohno, Hiroyuki

2013-01-01

We designed phosphonium-type zwitterion (ZI) to control the saturated water content of separated ionic liquid (IL) phase in the hydrophobic IL/water biphasic systems. The saturated water content of separated IL phase, 1-butyl-3-methyimidazolium bis(trifluoromethanesulfonyl)imide, was considerably improved from 0.4 wt% to 62.8 wt% by adding N,N,N-tripentyl-4-sulfonyl-1-butanephosphonium-type ZI (P555C4S). In addition, the maximum water content decreased from 62.8 wt% to 34.1 wt% by increasing KH2PO4/K2HPO4 salt content in upper aqueous phosphate buffer phase. Horse heart cytochrome c (cyt.c) was dissolved selectively in IL phase by improving the water content of IL phase, and spectroscopic analysis revealed that the dissolved cyt.c retained its higher ordered structure. Furthermore, cyt. c dissolved in IL phase was re-extracted again from IL phase to aqueous phase by increasing the concentration of inorganic salts of the buffer solution. PMID:24013379

Ion-Conductive and Thermal Properties of a Synergistic Poly(ethylene carbonate)/Poly(trimethylene carbonate) Blend Electrolyte.

PubMed

Li, Zhenguang; Mogensen, Ronnie; Mindemark, Jonas; Bowden, Tim; Brandell, Daniel; Tominaga, Yoichi

2018-05-11

Electrolytes comprising poly(ethylene carbonate) (PEC)/poly(trimethylene carbonate) (PTM C) with lithium bis(trifluoromethane sulfonyl)imide (LiTFSI) are prepared by a simple solvent casting method. Although PEC and PTMC have similar chemical structures, they are immiscible and two glass transitions are present in the differential scanning calorimetry (DSC) measurements. Interestingly, these two polymers change to miscible blends with the addition of LiTFSI, and the ionic conductivity increases with increasing lithium salt concentration. The optimum composition of the blend electrolyte is achieved at PEC 6 PTMC 4 , with a conductivity as high as 10 -6 S cm -1 at 50 °C. This value is greater than that for single PEC- and PTMC-based electrolytes. Moreover, the thermal stability of the blend-based electrolytes is improved as compared to PEC-based electrolytes. It is clear that the interaction between CO groups and Li + gives rise to a compatible amorphous phase of PEC and PTMC. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Molecular dynamics simulation studies of the interactions between ionic liquids and amino acids in aqueous solution.

PubMed

Tomé, Luciana I N; Jorge, Miguel; Gomes, José R B; Coutinho, João A P

2012-02-16

Although the understanding of the influence of ionic liquids (ILs) on the solubility behavior of biomolecules in aqueous solutions is relevant for the design and optimization of novel biotechnological processes, the underlying molecular-level mechanisms are not yet consensual or clearly elucidated. In order to contribute to the understanding of the molecular interactions established between amino acids and ILs in aqueous media, classical molecular dynamics (MD) simulations were performed for aqueous solutions of five amino acids with different structural characteristics (glycine, alanine, valine, isoleucine, and glutamic acid) in the presence of 1-butyl-3-methylimidazolium bis(trifluoromethyl)sulfonyl imide. The results from MD simulations enable to relate the properties of the amino acids, namely their hydrophobicity, to the type and strength of their interactions with ILs in aqueous solutions and provide an explanation for the direction and magnitude of the solubility phenomena observed in [IL + amino acid + water] systems by a mechanism governed by a balance between competitive interactions of the IL cation, IL anion, and water with the amino acids.

Making sense of enthalpy of vaporization trends for ionic liquids: new experimental and simulation data show a simple linear relationship and help reconcile previous data.

PubMed

Verevkin, Sergey P; Zaitsau, Dzmitry H; Emel'yanenko, Vladimir N; Yermalayeu, Andrei V; Schick, Christoph; Liu, Hongjun; Maginn, Edward J; Bulut, Safak; Krossing, Ingo; Kalb, Roland

2013-05-30

Vaporization enthalpy of an ionic liquid (IL) is a key physical property for applications of ILs as thermofluids and also is useful in developing liquid state theories and validating intermolecular potential functions used in molecular modeling of these liquids. Compilation of the data for a homologous series of 1-alkyl-3-methylimidazolium bis(trifluoromethane-sulfonyl)imide ([C(n)mim][NTf2]) ILs has revealed an embarrassing disarray of literature results. New experimental data, based on the concurring results from quartz crystal microbalance, thermogravimetric analyses, and molecular dynamics simulation have revealed a clear linear dependence of IL vaporization enthalpies on the chain length of the alkyl group on the cation. Ambiguity of the procedure for extrapolation of vaporization enthalpies to the reference temperature 298 K was found to be a major source of the discrepancies among previous data sets. Two simple methods for temperature adjustment of vaporization enthalpies have been suggested. Resulting vaporization enthalpies obey group additivity, although the values of the additivity parameters for ILs are different from those for molecular compounds.

The Toxicity of Perfluoro-N-Decanoic Acid and 2,3,7,8- Tetrachlorodibenzo-P-Dioxin in L5178Y Mouse Lymphoma Cells

DTIC Science & Technology

1983-03-01

ABSTRACT (Continue on reverse side If necessary and identify by block number) Perfluoro -n-decanoic acid ( PFDA ) causes toxic sequelae in vivo very similar to...acid analogs. All polyfluorinated acids tested (either perfluorinated or w-hydro-analogs) with chain length 9 or greater caused impairment of clone...of 5 to 7. The acute and subchronic toxicity of ammonium perfluoro -n-octanoate ( PFOA ) has been described in detail in both rats and rhesus monkeys

Mechanisms of Cellular Membrane Effects of TCDD, Selected Perfluorinated Acids and Polyhalogenated Aromatic Hydrocarbons

DTIC Science & Technology

1985-02-01

toxic response of both cell lines after treatment with the perfluorinated acids ( perfluoro -n-octanoic acid, 9-H hexadecafluoro-n-nonanoic acid, and...throughout the experiments to eliminate the effect of serum on toxicity. The results for perfluoro -n-octanoic acid ( PFOA ) in both cell lines are presented in...the TK+/+ cells but not in the TK+/- cells. The results for the perfluoro -n-decanoic acid ( PFDA ) are presented in Table 3. A dose-response reldtionship

Mechanisms of Cellular Membrane Effects of TCDD (2,3,7,8-Tetrachlorodibenzo-p-Dioxin) Selected Perfluorinated Acids and Polyhalogenated Aromatic Hydrocarbons.

DTIC Science & Technology

1986-10-15

tetrachloro dibenzo-p-dioxin (TCDD); dioxin; perfluoro -n-decanoic acid ( PFDA ); perfluoro -n-octanoic acid ( PFOA ); 3,31,4,41,5,51 hexachlorobiphenyl (345PCB) and...analysis of livers from rats treated with perfluoro -n-decanoic acid ( PFDA ) showed a decrease in stearic acid and an increase in 18 carbon unsaturates...effects of TCDD, PHAH and perfluorinated acids ( PFA ) on mammalian cell membrane function by examing the phenomenon of metabolic cooperation. Metabolic

One-pot palladium-catalyzed synthesis of sulfonyl fluorides from aryl bromides† †Electronic supplementary information (ESI) available: Experimental details and supporting characterisation data. See DOI: 10.1039/c6sc03924c Click here for additional data file.

PubMed Central

Davies, Alyn T.; Curto, John M.

2017-01-01

A mild, efficient synthesis of sulfonyl fluorides from aryl and heteroaryl bromides utilizing palladium catalysis is described. The process involves the initial palladium-catalyzed sulfonylation of aryl bromides using DABSO as an SO2 source, followed by in situ treatment of the resultant sulfinate with the electrophilic fluorine source NFSI. This sequence represents the first general method for the sulfonylation of aryl bromides, and offers a practical, one-pot alternative to previously described syntheses of sulfonyl fluorides, allowing rapid access to these biologically important molecules. Excellent functional group tolerance is demonstrated, with the transformation successfully achieved on a number of active pharmaceutical ingredients, and their precursors. The preparation of peptide-derived sulfonyl fluorides is also demonstrated. PMID:28451264

Polymerization of perfluorobutadiene at near-ambient conditions

NASA Technical Reports Server (NTRS)

Toy, M. S.

1971-01-01

Peroxide catalyst under mild conditions initiates homopolymerization of perfluoro butadiene to new linear perfluoro polyenes and vulcanizable fluoro elastomers. Resulting polyperfluoro butadiene serves as hard elastomer for good chemical resistance, as intermediate in graft polymerizations, and as crosslink for high molecular weight materials.

New approach for assessing human perfluoroalkyl exposure via hair.

PubMed

Alves, Andreia; Jacobs, Griet; Vanermen, Guido; Covaci, Adrian; Voorspoels, Stefan

2015-11-01

In the recent years hair has been increasingly used as alternative matrix in human biomonitoring (HBM) of environmental pollutants. Sampling advantages and time integration of exposure assessment seems the most attractive features of hair matrix. In the current study, a novel miniaturized method was developed and validated for measuring 15 perfluoroalkyl substances (PFAS), including perfluoro n-butanoic acid (PFBA), perfluoro n-pentanoic acid (PFPeA), perfluoro n-hexanoic acid (PFHxA), perfluoro n-heptanoic acid (PFHpA), perfluor n-octanoic acid (PFOA), perfluoro n-nonanoic acid (PFNA), perfluoro tetradecanoic acid (PFTeDA), perfluorobutane sulfonic acid (PFBS), perfluoro pentane sulfonic acid (PFPeS), perfluorohexane sulfonic acid (PFHxS), perfluoroheptane sulfonic acid (PFHpS), perfluorooctane sulfonic acid (PFOS), perfluorononane sulfonic acid (PFNS), perfluorodecane sulfonic acid (PFDS) and perfluorododecane sulfonic acid (PFDoS) in human hair by liquid chromatography tandem mass spectrometry (LC-MS/MS). After extraction using ethyl acetate, dispersive ENVI-Carb was used for clean-up. Good intra- and inter-day precision for low (LQ 5 ng/g hair) and high spike (HQ 15n g/g) levels were achieved (in general RSD <10%). The accuracy was assessed using recoveries (%), which ranged between 68-118% (LQ) and 70-121% (HQ). The instrumental limit of detection (LODi) and limit of quantification (LOQi) were between 1-4 pg/g hair and 3-13 pg/g hair, respectively. The method limit of quantification (LOQm) ranged between 6 and 301 pg/g hair. The PFAS levels were measured in 30 human hair samples indicating that the levels are low (14-1534 pg/g hair). Some PFAS were not present in any hair sample (e.g. PFHpA, PFTeDA, PFNA, PFPeS, PFHpS, PFOS and PFNS), while other PFAS were frequently detected (PFBA, PFPeA, PFHxA, PFOA, PFBS, PFHxS, PFOS, PFDS and PFDoS) in human hair. Although levels in general were low, there is evidence of higher human exposure to some analytes, such as PFBA, PFPeA, PFHxA, PFOA, PFBS, PFHxS, and PFDoS. The current study shows that hair is a suitable alternative non-invasive matrix for exposure assessment of PFAS. Copyright © 2015 Elsevier B.V. All rights reserved.

Solvent organization around the perfluoro group of coumarin 153 governs its photophysical properties: An experimental and simulation study of coumarin dyes in ethanol as well as fluorinated ethanol solvents.

PubMed

Mondal, Saptarsi; Halder, Ritaban; Biswas, Biswajit; Jana, Biman; Singh, Prashant Chandra

2016-05-14

The self-aggregation property of the perfluoro group containing molecules makes it important in the research fields of biology and polymer and organic synthesis. In the quest of understanding the role of the perfluoro group on the photophysical properties of perfluoro-containing molecules in biologically important fluoroethanol solvents, we have applied photophysical as well as molecular dynamics simulation techniques to explore the properties of perfluoro groups containing molecule coumarin-153 (C153) in ethanol (ETH), monofluoroethanol (MFE), difluoroethanol (DFE), and trifluoroethanol (TFE) and compared them with the molecules without perfluoro moiety, namely coumarin-6H (C6H) and coumarin-480 (C480). In contrast to C6H and C480, the excited state lifetime of C153 in fluorinated ETHs is not monotonic. The excited state lifetime of C153 decreases in MFE and DFE as compared to ETH, whereas in TFE, it increases as compared to MFE and DFE. Molecular dynamics simulation reveals that the carbon terminal away from the OH group of fluorinated ETHs has a preferential orientation near the perfluoro (CF3) group of C153. In MFE and DFE, the CF3 group of C153 prefers to have a CF2-F⋯H -(CHF) type of electrostatic interaction over CF2-F⋯F -(CH2) kind of dispersion interaction which increases the rate of nonradiative decay, probably due to the electrostatic nature of the CF2-F⋯H -(CHF) hydrogen bond. On the other hand, in TFE, C-F⋯ F-C type of dispersion interaction, also known as fluorous interaction, takes place between the CF3 groups of C153 and TFE which decreases the rate of nonradiative rate as compared to MFE and DFE, leading to the increased lifetime of C153 in TFE. Photophysical and MD simulation studies clearly depict that the structural organization of solvents and their interaction with the fluorocarbon group are crucial factors for the photophysical behavior of the fluorocarbon containing molecules.

Solvent organization around the perfluoro group of coumarin 153 governs its photophysical properties: An experimental and simulation study of coumarin dyes in ethanol as well as fluorinated ethanol solvents

NASA Astrophysics Data System (ADS)

Mondal, Saptarsi; Halder, Ritaban; Biswas, Biswajit; Jana, Biman; Singh, Prashant Chandra

2016-05-01

The self-aggregation property of the perfluoro group containing molecules makes it important in the research fields of biology and polymer and organic synthesis. In the quest of understanding the role of the perfluoro group on the photophysical properties of perfluoro-containing molecules in biologically important fluoroethanol solvents, we have applied photophysical as well as molecular dynamics simulation techniques to explore the properties of perfluoro groups containing molecule coumarin-153 (C153) in ethanol (ETH), monofluoroethanol (MFE), difluoroethanol (DFE), and trifluoroethanol (TFE) and compared them with the molecules without perfluoro moiety, namely coumarin-6H (C6H) and coumarin-480 (C480). In contrast to C6H and C480, the excited state lifetime of C153 in fluorinated ETHs is not monotonic. The excited state lifetime of C153 decreases in MFE and DFE as compared to ETH, whereas in TFE, it increases as compared to MFE and DFE. Molecular dynamics simulation reveals that the carbon terminal away from the OH group of fluorinated ETHs has a preferential orientation near the perfluoro (CF3) group of C153. In MFE and DFE, the CF3 group of C153 prefers to have a CF2—F⋯H —(CHF) type of electrostatic interaction over CF2—F⋯F —(CH2) kind of dispersion interaction which increases the rate of nonradiative decay, probably due to the electrostatic nature of the CF2—F⋯H —(CHF) hydrogen bond. On the other hand, in TFE, C—F⋯ F—C type of dispersion interaction, also known as fluorous interaction, takes place between the CF3 groups of C153 and TFE which decreases the rate of nonradiative rate as compared to MFE and DFE, leading to the increased lifetime of C153 in TFE. Photophysical and MD simulation studies clearly depict that the structural organization of solvents and their interaction with the fluorocarbon group are crucial factors for the photophysical behavior of the fluorocarbon containing molecules.

Syntheses and Degradations of Fluorinated Heterocyclics. 3; Perfluoroalkyl and Perfluoroalkylether-1,3,4-Oxadiazoles

NASA Technical Reports Server (NTRS)

Paciorek, K. J. L.; Kaufman, J.; Nakahara, J. H.; Ito, T. I.; Kratzer, R. H.; Rosser, R. W.; Parker, J. A.

1977-01-01

2,5-Bis(perfluoro-n-heptyl)-, 2-perfluoroalkylether-5-perfluoro-n- heptyl- , and 2 , 5-bisperfluoroalkylether-1,3,4-oxadiazoles were synthesized and characterized. 2,5-Bis(perfluoro-n-heptyl)-1,3,4-oxadiazole was thermally and hydrolytically stable at 325 C; however, in the presence of air, degradation took place at 235 C. The perfluoroalkylether analogue exhibited thermal and hydrolytic stability at 325 C; it was found to be unaffected by jet-A fuel and air at 235 C. At 325 C in air some degradation occurred as evidenced by volatiles production, oxygen consumption, and 96% starting material recovery.

Phase behaviour, interactions, and structural studies of (amines+ionic liquids) binary mixtures.

PubMed

Jacquemin, Johan; Bendová, Magdalena; Sedláková, Zuzana; Blesic, Marijana; Holbrey, John D; Mullan, Claire L; Youngs, Tristan G A; Pison, Laure; Wagner, Zdeněk; Aim, Karel; Costa Gomes, Margarida F; Hardacre, Christopher

2012-05-14

We present a study on the phase equilibrium behaviour of binary mixtures containing two 1-alkyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}imide-based ionic liquids, [C(n)mim] [NTf(2)] (n=2 and 4), mixed with diethylamine or triethylamine as a function of temperature and composition using different experimental techniques. Based on this work, two systems showing an LCST and one system with a possible hourglass shape are measured. Their phase behaviours are then correlated and predicted by using Flory-Huggins equations and the UNIQUAC method implemented in Aspen. The potential of the COSMO-RS methodology to predict the phase equilibria was also tested for the binary systems studied. However, this methodology is unable to predict the trends obtained experimentally, limiting its use for systems involving amines in ionic liquids. The liquid-state structure of the binary mixture ([C(2)mim] [NTf(2)]+diethylamine) is also investigated by molecular dynamics simulation and neutron diffraction. Finally, the absorption of gaseous ethane by the ([C(2)mim][NTf(2)]+diethylamine) binary mixture is determined and compared with that observed in the pure solvents. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ionic liquid supported on an electrodeposited polycarbazole film for the headspace solid-phase microextraction and gas chromatography determination of aromatic esters.

PubMed

Feng, Yuanyuan; Zhao, Faqiong; Zeng, Baizhao

2015-05-01

A polycarbazole film was electrodeposited on a stainless-steel wire from a solution of N,N-dimethylformamide/propylene carbonate (1:9 v/v) containing 0.10 M carbazole and 0.10 M tetrabutylammonium perchlorate. The obtained polycarbazole fiber was immersed into an ionic liquid (1-hydroxyethyl-3-methyl imidazolium bis[(trifluoromethyl)sulfonyl]imide) solution (in dimethylsulfoxide) for 30 min, followed by drying under an infrared lamp. The resulting polycarbazole/ionic liquid fiber was applied to the headspace solid-phase microextraction and determination of aromatic esters by coupling with gas chromatography and flame ionization detection. Under the optimized conditions, the limits of detection were below 61 ng/L (S/N = 3) and the linear ranges were 0.061-500 μg/L with correlation coefficients above 0.9876. The relative standard deviations were below 4.8% (n = 5) for a single fiber, and below 9.9% for multi-fiber (n = 4). This fiber also exhibited good stability. It could be used for more than 160 times of headspace solid-phase microextraction and could withstand a high temperature up to 350°C. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of diverse pyrazole-4-sulfonyl chlorides starting from 2-(benzylthio)malonaldehyde.

PubMed

Sokolyuk, Pavlo A; Kondratov, Ivan S; Gavrylenko, Olexiy V; Tolmachov, Andrey A

2016-02-01

A series of pyrazole-4-sulfonyl chlorides was obtained by a convenient 2-step method starting from synthetically available 2-(benzylthio)malonaldehyde. The method can be applied for the effective multi-gram synthesis of diverse pyrazole-containing sulfonyl chlorides which are mostly not available by other methods.

Thermal oxidative degradation reactions of linear perfluoroalky lethers

NASA Technical Reports Server (NTRS)

Jones, W. R., Jr.; Paciorek, K. J. L.; Ito, T. I.; Kratzer, R. H.

1982-01-01

Thermal and thermal oxidative stability studies were performed on linear perfluoro alkyl ether fluids. The effect on degradation by metal catalysts and degradation inhibitors are reported. The liner perfluoro alkylethers are inherently unstable at 316 C in an oxidizing atmosphere. The metal catalysts greatly increased the rate of degradation in oxidizing atmospheres. In the presence of these metals in an oxidizing atmosphere, the degradation inhibitors were highly effective in arresting degradation at 288 C. However, the inhibitors had only limited effectiveness at 316 C. The metals promote degradation by chain scission. Based on elemental analysis and oxygen consumption data, the linear perfluoro alkylether fluids have a structural arrangement based on difluoroformyl and tetrafluoroethylene oxide units, with the former predominating.

Studies of the kinetics and mechanisms of perfluoroether reactions on iron and oxidized iron surfaces

NASA Technical Reports Server (NTRS)

Napier, Mary E.; Stair, Peter C.

1992-01-01

Polymeric perfluoroalkylethers are being considered for use as lubricants in high temperature applications, but have been observed to catalytically decompose in the presence of metals. X-ray photoelectron spectroscopy (XPS) and temperature programmed desorption (TPD) were used to explore the decomposition of three model fluorinated ethers on clean polycrystalline iron surfaces and iron surfaces chemically modified with oxygen. Low temperature adsorption of the model fluorinated ethers on the clean, oxygen modified and oxidized iron surfaces was molecular. Thermally activated defluorination of the three model compounds was observed on the clean iron surface at remarkably low temperatures, 155 K and below, with formation of iron fluoride. Preferential C-F bond scission occurred at the terminal fluoromethoxy, CF3O, of perfluoro-1-methoxy-2-ethoxy ethane and perfluoro-1-methoxy-2-ethoxy propane and at CF3/CF2O of perfluoro-1,3-diethoxy propane. The reactivity of the clean iron toward perfluoroalkylether decomposition when compared to other metals is due to the strength of the iron fluoride bond and the strong electron donating ability of the metallic iron. Chemisorption of an oxygen overlayer lowered the reactivity of the iron surface to the adsorption and decomposition of the three model fluorinated ethers by blocking active sites on the metal surface. Incomplete coverage of the iron surface with chemisorbed oxygen results in a reaction which resembles the defluorination reaction observed on the clean iron surface. Perfluoro-1-methoxy-2-ethoxy ethane reacts on the oxidized iron surface at 138 K, through a Lewis acid assisted cleavage of the carbon oxygen bond, with preferential attack at the terminal fluoromethoxy, CF3O. The oxidized iron surface did not passivate, but became more reactive with time. Perfluoro-1-methoxy-2-ethoxy propane and perfluoro-1,3-diethoxy propane desorbed prior to the observation of decomposition on the oxidized iron surface.

Copper-Catalyzed Sulfonyl Azide-Alkyne Cycloaddition Reactions: Simultaneous Generation and Trapping of Copper-Triazoles and -Ketenimines for the Synthesis of Triazolopyrimidines.

PubMed

Nallagangula, Madhu; Namitharan, Kayambu

2017-07-07

First simultaneous generation and utilization of both copper-triazole and -ketenimine intermediates in copper-catalyzed sulfonyl azide-alkyne cycloaddition reactions is achieved for the one-pot synthesis of triazolopyrimidines via a novel copper-catalyzed multicomponent cascade of sulfonyl azides, alkynes, and azirines. Significantly, the reaction proceeds under very mild conditions in good yields.

Asymmetric 1,2-perfluoroalkyl migration: easy access to enantioenriched α-hydroxy-α-perfluoroalkyl esters.

PubMed

Wang, Pan; Feng, Liang-Wen; Wang, Lijia; Li, Jun-Fang; Liao, Saihu; Tang, Yong

2015-04-15

This study has led to the development of a novel, highly efficient, 1,2-perfluoro-alkyl/-aryl migration process in reactions of hydrate of 1-perfluoro-alkyl/-aryl-1,2-diketones with alcohols, which are promoted by a Zn(II)/bisoxazoline and form α-perfluoro-alkyl/-aryl-substituted α-hydroxy esters. With (-)-8-phenylmenthol as the alcohol, the corresponding menthol esters are generated in high yields with excellent levels of diastereoselectivity. The mechanistic studies show that the benzilic ester-type rearrangement reaction takes place via an unusual 1,2-migration of electron-deficient trifluoromethyl group rather than the phenyl group. The overall process serves as a novel, efficient, and simple approach for the synthesis of highly enantioenriched, biologically relevant α-hydroxy-α-perfluoroalkyl carboxylic acid derivatives.

New stable perfluoroallyl radical from perfluoro-2,4-dimethyl-3-ethylpentene-2 and its photoconversion reactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shvedova, M.K.; Allayarov, S.R.; Barkalov, I.M.

1988-05-01

The thermally and chemically stable perfluoroally radical is formed in the radiolysis of perfluoro-2, 4-dimethyl-3-ethylpentene-2. A phototransformation of this radical into other radicals takes place under the action of UV light (/lambda/ < 300 nm) which are thermally unstable. Samples containing up to 90% FMP and 10% of its isomers were placed into ampules made of quartz or SK-4B glass, which gave to EPR signal after irradiation; the ampules were evacuated to a pressure of 0.13 Pa, frozen to 77 K, and irradiated with /sup 60/Co /lambda/-quanta at 77 K with doses up to 200 kGy. Irradiation with UV lightmore » was performed at 77 K with light from a DRSh-1000 lamp.« less

Methylsulfonylmethane

MedlinePlus

... Dimethyl Sulfone MSM, DMSO2, Methyl Sulfone, Methyl Sulfonyl Methane, Methyl Sulphonyl Methane, Méthyle Sulfonyle Méthane, Méthyle Sulphonyle Méthane, Méthylsulfonylméthane, Metilsulfonilmentano, ...

78 FR 57285 - 2,5-Furandione, Polymer With Ethenylbenzene, Hydrolyzed, 3-(Dimethylamino)propyl Imide, Imide...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-18

..., Polymer With Ethenylbenzene, Hydrolyzed, 3- (Dimethylamino)propyl Imide, Imide With Polyethylene..., polymer with ethenylbenzene, hydrolyzed, 3-(dimethylamino)propyl imide, imide with polyethylene... to establish a maximum permissible level for residues of 2,5-furandione, polymer with ethenylbenzene...

Elemental Fluorine Based Syntheses of Pentafluoro Phenly and other Aromatic Perfluoropolyether Polymers

DTIC Science & Technology

1994-01-31

ECM 300 PA. 13.8 Pe: -1.0 SCALE $000 00 MZ/o• 14.7171 Pe•/CM 50 0 -50 -100 -150 -200 PPM 3 Very unusual perfluoro polyketone structures have beeni...11PIA C14 LI) LL. L)V LLL cim C45 We think the zeolitic solid state structure of this very interesting perfluoro polyketone is most unusual and there

Synthesis and Characterization of Perfluoroalkyl Heterocyclic Elastomers

DTIC Science & Technology

Perfluoro -4,9,14,19-tetraoxadocosane diimidate-dihydroxybenzidine polymers have been prepared from carefully purified monomers. DTA measurements show...attained was 0.28. Polymers prepared from dihydroxybenzidine and methyl perfluoro -4,9-dioxadodecanediimidate soften at about 65C. with a Tg near 21C...of 3,3’-diamino-4,4’-dihydroxybenzophenone with methyl perfluorosebacimidate . The polymer softens at 205C., forms films and has excellent thermal

A New Approach to Highly Fluorinated Lubricants.

DTIC Science & Technology

1987-10-30

demonstrated the value of perfluoroalkyl groups being present. 7 In this way, xrious perfluoroethers were characterised, thus demonstrating the...mixture, containing four components (g.l.c. col. A 450C), was separated using preparative scale g.l.c. techniques to give:- perfluoropentane (4%); perfluoro ...CHRFOCHRFCH2 OCHRFCH 3 ) (where RF - CF 2CFHCF3 ) 2. These adducts were then fluorinated by cobalt trifluoride to give corresponding perfluoro -ethers

Correlation between ion diffusional motion and ionic conductivity for different electrolytes based on ionic liquid.

PubMed

Kaur, Dilraj Preet; Yamada, K; Park, Jin-Soo; Sekhon, S S

2009-04-23

Room temperature ionic liquid 2,3-dimethyl-1-hexylimidazolium bis(trifluoromethane sulfonyl)imide (DMHxImTFSI) has been synthesized and used in the preparation of polymer gel electrolytes containing polymethylmethacrylate and propylene carbonate (PC). The onset of ion diffusional motion has been studied by (1)H and (19)F NMR spectroscopy and the results obtained for ionic liquid, liquid electrolytes, and polymer gel electrolytes have been correlated with the ionic conductivity results for these electrolytes in the 100-400 K temperature range. The temperature at which (1)H and (19)F NMR lines show motional narrowing and hence ion diffusional motion starts has been found to be closely related to the temperature at which a large increase in ionic conductivity has been observed for these electrolytes. Polymer gel electrolytes have high ionic conductivity over a wide range of temperatures. Thermogravimetric analysis/differential scanning calorimetry studies show that the ionic liquid (DMHxImTFSI) used in the present study is thermally stable up to 400 degrees C, whereas the addition of PC lowers the thermal stability of polymer gel electrolytes containing the ionic liquid. Different electrolytes have been observed to show high ionic conductivity in different range of temperatures, which can be helpful in the design of polymer gel electrolytes for specific applications.

A novel poly(3,4-ethylenedioxythiophene)-ionic liquid composite coating for the headspace solid-phase microextraction and gas chromatography determination of several alcohols in soft drinks.

PubMed

Wu, Mian; Zhang, Haibo; Zhao, Faqiong; Zeng, Baizhao

2014-11-19

A novel poly(3,4-ethylenedioxythiophene)-ionic liquid (i.e., 1-hydroxyethyl-3-methyl imidazolium-bis[(trifluoromethyl)sulfonyl]imide) composite film was electrodeposited on a Pt wire for headspace solid-phase microextraction. The film showed nodular structure and had large specific surface. In addition, it displayed high thermal stability (up to 300°C) and durable property (could be used for more than 200 times). Coupled with gas chromatography-flame ionization detection, the resulting fiber was applied to the headspace solid-phase microextraction and determination of several alcohols (i.e., linalool, nonanol, terpineol, geraniol, decanol and dodecanol). It presented higher extraction capability in comparison with the poly(3,4-ethylenedioxythiophene) and commercial polydimethylsiloxane/divinylbenzene fiber. Under the optimized conditions, the linear ranges exceeded three magnitudes with correlation coefficients above 0.9952 and the low limits of detection were 34.2-81.3ng L(-1). For different alcohols the repeatabilities (defined as RSD) were <5.8% and <7.8% for single fiber (n=5) and fiber-to-fiber (n=4), respectively. The proposed method was applied to the determination of these alcohols in real samples with acceptable recoveries from 81.1% to 106.6%. Copyright © 2014 Elsevier B.V. All rights reserved.

Mutual solubility of water and structural/positional isomers of N-alkylpyridinium-based ionic liquids.

PubMed

Freire, Mara G; Neves, Catarina M S S; Shimizu, Karina; Bernardes, Carlos E S; Marrucho, Isabel M; Coutinho, João A P; Canongia Lopes, José N; Rebelo, Luís Paulo N

2010-12-09

Despite many previous important contributions to the characterization of the liquid-liquid phase behavior of ionic liquids (ILs) plus water systems, a gap still exists as far as the effect of isomers (of ILs) is concerned. Therefore, in this work, a comprehensive study of the liquid-liquid equilibria between water and isomeric pyridinium-based ionic liquids has been performed. Atmospheric pressure mutual solubilities between water and pyridinium-based ionic liquids combined with the common anion bis[(trifluoromethyl)sulfonyl]imide were experimentally determined between (288.15 and 318.15) K. The main goal of this work is to study the isomeric effects on the pyridinium-based cation, namely, the structural and positional isomerism, as well as the alkyl side chain length. To the best of our knowledge, the influence of both structural and positional isomerism on the liquid-liquid behavior in ionic-liquid-water-containing systems is an unexplored field and is here assessed for the first time. Moreover, from the experimental solubility data, several infinite dilution molar thermodynamic functions of solution, namely, the Gibbs energy, the enthalpy, and the entropy, were estimated and discussed. In addition, aiming at gathering a broader picture of the underlying thermodynamic solvation phenomenon, molecular dynamics simulations were also carried out for the same experimental systems.

Dissociation of protonated N-(3-phenyl-2H-chromen-2-ylidene)-benzenesulfonamide in the gas phase: cyclization via sulfonyl cation transfer.

PubMed

Wang, Shanshan; Dong, Cheng; Yu, Lian; Guo, Cheng; Jiang, Kezhi

2016-01-15

In the tandem mass spectrometry of protonated N-(3-phenyl-2H-chromen-2-ylidene)benzenesulfonamides, the precursor ions have been observed to undergo gas-phase dissociation via two competing channels: (a) the predominant channel involves migration of the sulfonyl cation to the phenyl C atom and the subsequent loss of benzenesulfinic acid along with cyclization reaction, and (b) the minor one involves dissociation of the precursor ion to give an ion/neutral complex of [sulfonyl cation/imine], followed by decomposition to afford sulfonyl cation or the INC-mediated electron transfer to give an imine radical cation. The proposed reaction channels have been supported by theoretical calculations and D-labeling experiments. The gas-phase cyclization reaction originating from the N- to C-sulfonyl cation transfer has been first reported to the best of our knowledge. For the substituted sulfonamides, the presence of electron-donating groups (R(2) -) at the C-ring effectively facilitates the reaction channel of cyclization reaction, whereas that of electron-withdrawing groups inhibits this pathway. Copyright © 2015 John Wiley & Sons, Ltd.

Enantioselective synthesis of cis-decalins using organocatalysis and sulfonyl Nazarov reagents.

PubMed

Peña, Javier; Silveira-Dorta, Gastón; Moro, Rosalina F; Garrido, Narciso M; Marcos, Isidro S; Sanz, Francisca; Díez, David

2015-04-10

The first organocatalytic synthesis of cis-decalins using sulfonyl Nazarov reagents is reported. The Jørgensen's catalyst directs this highly enantioselective synthesis using different cyclohexenal derivatives.

Cellular Effects of Perfluorinated Fatty Acids.

DTIC Science & Technology

1985-01-01

perfluoro -n-de canoic acid ( PFDA ), fluoresce e -- I j ~recovery after photobleaching (FRAPB), cell culture ~ . 19. ABSTRACT (Continue an reverse if...necessmzejj dctiy by block number) --Tecompoubd perfluor i--ecan’oic’ acid ( PFDA ) was exposed to three tissue culturer cell lines, PTK2 (kidney),/BRL (buffalo...all cell systems. In particular, previous in vivo and in vitro studies on the similarities of the toxic effects of perfluoro -n-decanoic acid ( PFDA ) and

An ultra-sensitive method for the analysis of perfluorinated alkyl acids in drinking water using a column switching high-performance liquid chromatography tandem mass spectrometry.

PubMed

Dasu, Kavitha; Nakayama, Shoji F; Yoshikane, Mitsuha; Mills, Marc A; Wright, J Michael; Ehrlich, Shelley

2017-04-21

In epidemiological research, it has become increasingly important to assess subjects' exposure to different classes of chemicals in multiple environmental media. It is a common practice to aliquot limited volumes of samples into smaller quantities for specific trace level chemical analyses. A novel method was developed for the determination of 14 perfluorinated alkyl acids (PFAAs) in small volumes (10mL) of drinking water using off-line solid phase extraction (SPE) pre-treatment followed by on-line pre-concentration on a WAX column before analysis on column-switching high performance liquid chromatography tandem mass spectrometry (HPLC-MS/MS). In general, large volumes (100-1000mL) have been used for the analysis of PFAAs in drinking water. The current method requires approximately 10mL of drinking water concentrated by using an SPE cartridge and eluted with methanol. A large volume injection of the extract was introduced on to a column-switching HPLC-MS/MS using a mix-mode SPE column for the trace level analysis of PFAAs in water. The recoveries for most of the analytes in the fortified laboratory blanks ranged from 73±14% to 128±5%. The lowest concentration minimum reporting levels (LCMRL) for the 14 PFAAs ranged from 0.59 to 3.4ng/L. The optimized method was applied to a pilot-scale analysis of a subset of drinking water samples from an epidemiological study. These samples were collected directly from the taps in the households of Ohio and Northern Kentucky, United States and the sources of drinking water samples are both surface water and ground water, and supplied by different water distribution facilities. Only five PFAAs, perfluoro-1-butanesulfonic acid (PFBS), perfluoro-1- -hexanesulfonic acid (PFHxS), perfluoro-1-octanesulfonic acid (PFOS), perfluoro-n-heptanoic acid (PFHpA) and perfluoro-n-octanoic acid (PFOA) are detected above the LCMRL values. The median concentrations of these five PFAAs detected in the samples was ≤4.1ng/L with PFOS at 7.6ng/L and PFOA at 10ng/L. Concentrations of perfluoro-1-decanesulfonic acid, PFDS and other perfluoroalkyl carboxylic acids were below the LCMRL values. Copyright © 2017 Elsevier B.V. All rights reserved.

Superhydrophobic, Hybrid, Electrospun Cellulose Acetate Nanofibrous Mats for Oil/Water Separation by Tailored Surface Modification.

PubMed

Arslan, Osman; Aytac, Zeynep; Uyar, Tamer

2016-08-03

Electrospun cellulose acetate nanofibers (CA-NF) have been modified with perfluoro alkoxysilanes (FS/CA-NF) for tailoring their chemical and physical features aiming oil-water separation purposes. Strikingly, hybrid FS/CA-NF showed that perfluoro groups are rigidly positioned on the outer surface of the nanofibers providing superhydrophobic characteristic with a water contact angle of ∼155°. Detailed analysis showed that hydrolysis/condensation reactions led to the modification of the acetylated β(1 → 4) linked d-glucose chains of CA transforming it into a superhydrophobic nanofibrous mat. Analytical data have revealed that CA-NF surfaces can be selectively controlled for fabricating the durable, robust and water resistant hybrid electrospun nanofibrous mat. The -OH groups available on the CA structure allowed the basic sol-gel reactions started by the reactive FS hybrid precursor system which can be monitored by spectroscopic analysis. Since alkoxysilane groups on the perfluoro silane compound are capable of reacting for condensation together with the CA, superhydrophobic nanofibrous mat is obtained via electrospinning. This structural modification led to the facile fabrication of the novel oil/water nanofibrous separator which functions effectively demonstrated by hexane/oil and water separation experiments. Perfluoro groups consequently modified the hydrophilic CA nanofibers into superhydrophobic character and therefore FS/CA-NF could be quite practical for future applications like water/oil separators, as well as self-cleaning or water resistant nanofibrous structures.

Travelers with immune-mediated inflammatory diseases: are they different?

PubMed

Jaeger, Veronika K; Rüegg, Rolanda; Steffen, Robert; Hatz, Christoph; Bühler, Silja

2015-01-01

Patients with immune-mediated inflammatory diseases (IMIDs) increasingly benefit from improved health due to new therapeutic regimens allowing increasing numbers of such patients to travel overseas. This study aims to assess the proportion of IMID travelers seeking advice at the Travel Clinic of the University of Zurich, Switzerland, and to determine whether demographics, travel, and vaccination patterns differ between IMID- and non-IMID travelers. Pre-travel visits and differences between IMID- and non-IMID travelers were assessed; logistic regression was used to adjust for confounders. Among 22,584 travelers who visited the Zurich Travel Clinic in a 25-month period, 1.8% suffered from an IMID, with gastroenterological and rheumatic conditions being the most common; 34.2% were using immunosuppressive or immunomodulatory medication. The reasons for travel and the destinations did not differ between IMID- and non-IMID travelers, Thailand and India being the most common destinations. IMID travelers stayed less often for longer than 1 month abroad and traveled less frequently on a low budget. Inactivated vaccines were similarly administered to both groups, while live vaccines were given half as often to IMID travelers. The increasing numbers of IMID patients, many using immunosuppressive or immunomodulatory therapy, show similar travel patterns as non-IMID travelers. Thus, they are exposed to the same travel health risks, vaccine-preventable infections being one among them. Particularly, in view of the fact that live attenuated vaccines are less often administered to IMID patients more data are needed on the safety and immunogenicity of vaccines and on travel-specific risks to be able to offer evidence-based pre-travel health advice. © 2014 International Society of Travel Medicine.

Rhodium(II)-Catalyzed and Thermally Induced Intramolecular Migration of N-Sulfonyl-1,2,3-triazoles: New Approaches to 1,2-Dihydroisoquinolines and 1-Indanones.

PubMed

Sun, Run; Jiang, Yu; Tang, Xiang-Ying; Shi, Min

2016-04-11

New rhodium(II)-catalyzed or thermally induced intramolecular alkoxy group migration of N-sulfonyl-1,2,3-triazoles has been developed, affording divergent synthesis of 1,2-dihydroisoquinoline and 1-indanone derivatives according to different conditions. N-Sulfonyl keteneimine is the key intermediate for the synthesis of dihydroisoquinoline, whereas the aza-vinyl carbene intermediate results in the formation of 1-indanone. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Lithium salt with a super-delocalized perfluorinated sulfonimide anion as conducting salt for lithium-ion cells: Physicochemical and electrochemical properties

NASA Astrophysics Data System (ADS)

Zhang, Heng; Han, Hongbo; Cheng, Xiaorong; Zheng, Liping; Cheng, Pengfei; Feng, Wenfang; Nie, Jin; Armand, Michel; Huang, Xuejie; Zhou, Zhibin

2015-11-01

Lithium salt with a super-delocalized imide anion, namely (trifluoromethane(S-trifluoromethanesulfonylimino)sulfonyl) (trifluoromethanesulfonyl)imide ([CF3SO(=NSO2CF3)2]-), [sTFSI]-), has been prepared and studied as conducting salt for Li-ion cells. The fundamental physicochemical and electrochemical properties of neat Li[sTFSI] and its carbonate-based liquid electrolyte have been characterized with various chemical and electrochemical tools. Li[sTFSI] shows a low melting point at 118 °C, and is thermally stable up to 300 °C without decomposition on the spectra of differential scanning calorimetry-thermogravimetry-mass spectrometry (DSC-TG-MS). The electrolyte of 1.0 M (mol dm-3) Li[sTFSI] in ethylene carbonate (EC)/ethyl-methyl-carbonate (EMC) (3:7, v/v) containing 0.3% water does not show any hydrolytic decomposition on the spectra of 1H and 19F NMR, after storage at 85 °C for 10 days. The conductivities of 1.0 M Li[sTFSI]-EC/EMC (3:7, v/v) are slightly lower than those of Li[(CF3SO2)2N] (LiTFSI), but higher than those of Li[(C2F5SO2)2N] (LiBETI). The electrochemical behavior of Al foil in the Li[sTFSI]-based electrolyte has been investigated by using cyclic voltammetry and chronoamperometry, and scanning electron microscope (SEM). It is illustrated that Al metal does not corrode in the high potential region (3-5 V vs. Li/Li+) in the Li[sTFSI]-based electrolyte. On Pt electrode, the Li[sTFSI]-based electrolyte is highly resistant to oxidation (ca. 5 V vs. Li/Li+), and is also resistant to reduction to allow Li deposition and stripping. The applicability of Li[sTFSI] as conducting salt for Li-ion cells has been tested using graphite/LiCoO2 cells. It shows that the cell with Li[sTFSI] displays better cycling performance than that with LiPF6.

Two-Dimensional Electrophoretic Analysis of Subcellular Liver Fractions and Isolated Hepatocytes from Normal and PFDA Treated Rats

DTIC Science & Technology

1990-05-28

Continue on reverse if necessary and identify by block number) FIELD GROUP SUB-GROUP perfluoro.n-decanoic acid ; two-dimensional electrophoresis...hepatotoxicity; cell fractions; liver 1 t ABSTRACT (Continue on reverse if necessary and identify by block number) Perfluoro-n-decanoic acid (PFDA) effects...Unu::’-. ’. I AFOSR Ju .T , Building 410 Bolling AFB, DC 20332-6448 By Dist V’ lml mm mm i INTRODUCTION Perfluorocarboxylic acids and other

The Molecular Anatomy of PFDA Hepatotoxicity as Studied by Two- Dimensional Electrophoresis.

DTIC Science & Technology

1991-01-03

Available Copy 93 06 124 Page 3 INTRODUCTION Perfluoro -n-decanoic acid ( PFDA ) is a ten carbon straight-chain perfluorinated carboxylic acid whose surfactant...Rats were injected with a single intraperitoneal dose of 2, 20, 50, or 100 mg PFDA /kg body weight; 75, 100, 150 mg PFOA /kg (eight carbon analog); or 3...TERMS (Continue on reverse if necessary and identify by block number) FIELD IGROUP SUB-GROUP perfluoro -n-decanoic acid; two-dimensional electro- P

Perfluoro (Imidoylamidine) diamidines

NASA Technical Reports Server (NTRS)

Rosser, R. W.; Chen, T. S.; Cheng, C. H. (Inventor)

1986-01-01

Perfluoroether triazine elastomers having improved properties are prepared from oligomeric imidoylamidines that were in turn, prepared by the process of: (1) reacting a perfluorodinitrile with liquid ammonia to yield a perfluorodiamidine, (2) isolating the perfluorodiamidine, (3) reacting the isolated diamidine with a perfluorodinitrile to yield a perfluoro(imidoylamidine) dinitrile, and then repeating the steps to sequentially grow an oligomer of desired molecular size. The isolated amidine and nitrile intermediates are also disclosed. The elastomers can be fashioned into seals, gaskets, and sealing components and the like.

Development of critical molecular weight-property specifications for high performance polymers used as adhesives and composites

NASA Technical Reports Server (NTRS)

Kranbuehl, D. E.

1982-01-01

The polyimide resin, LARC-160, was prepared from diethyl-3, 3', 4,4'-benzophenone tetracarboxylate, ethyl-5-norbornene-2,3-dicarboxylate and Jeffamine AP-22. The imidization reactions of NE and BTDE were studied by HPLC, C-13-NMR and IR. NE imidizes slowly at 12 C; BTDE imidizes when the resin is heated above 100 C. Both imidization reactions proceed directly to the imide. Neither amic acid is present in significant quantities at any stage of the imidization reactions. The monomer mixture was stored at 12 C for periods up to 14 months. The effects of resin aging at this temperature on the chemical composition of the resin monomer mixture and the imidized polymer formed on curing were investigated. Aging the resin monomer mixture has the effect of partially advancing the imidization reaction. The average size of the cured polymer increases slightly with resin age.

Revisiting imidazolium based ionic liquids: Effect of the conformation bias of the [NTf2] anion studied by molecular dynamics simulations

NASA Astrophysics Data System (ADS)

Neumann, Jan; Golub, Benjamin; Odebrecht, Lisa-Marie; Ludwig, Ralf; Paschek, Dietmar

2018-05-01

We study ionic liquids composed of 1-alkyl-3-methylimidazolium cations and bis(trifluoromethyl-sulfonyl)imide anions ([CnMIm][NTf2]) with varying chain-length n = 2, 4, 6, 8 by using molecular dynamics simulations. We show that a reparametrization of the dihedral potentials as well as charges of the [NTf2] anion leads to an improvement of the force field model introduced by Köddermann, Paschek, and Ludwig [ChemPhysChem 8, 2464 (2007)] (KPL-force field). A crucial advantage of the new parameter set is that the minimum energy conformations of the anion (trans and gauche), as deduced from ab initio calculations and Raman experiments, are now both well represented by our model. In addition, the results for [CnMIm][NTf2] show that this modification leads to an even better agreement between experiment and molecular dynamics simulation as demonstrated for densities, diffusion coefficients, vaporization enthalpies, reorientational correlation times, and viscosities. Even though we focused on a better representation of the anion conformation, also the alkyl chain-length dependence of the cation behaves closer to the experiment. We strongly encourage to use the new NGOLP (Neumann, Golub, Odebrecht, Ludwig, Paschek) force field for the [NTf2] anion instead of the earlier KPL parameter set for computer simulations aiming to describe the thermodynamics, dynamics, and also structure of imidazolium-based ionic liquids.

High Voltage LiNi0.5Mn1.5O4/Li4Ti5O12 Lithium Ion Cells at Elevated Temperatures: Carbonate- versus Ionic Liquid-Based Electrolytes.

PubMed

Cao, Xia; He, Xin; Wang, Jun; Liu, Haidong; Röser, Stephan; Rad, Babak Rezaei; Evertz, Marco; Streipert, Benjamin; Li, Jie; Wagner, Ralf; Winter, Martin; Cekic-Laskovic, Isidora

2016-10-05

Thanks to its high operating voltage, the LiNi 0.5 Mn 1.5 O 4 (LNMO) spinel represents a promising next-generation cathode material candidate for Lithium ion batteries. However, LNMO-based full-cells with organic carbonate solvent electrolytes suffer from severe capacity fading issues, associated with electrolyte decomposition and concurrent degradative reactions at the electrode/electrolyte interface, especially at elevated temperatures. As promising alternatives, two selected LiTFSI/pyrrolidinium bis(trifluoromethane-sulfonyl)imide room temperature ionic liquid (RTIL) based electrolytes with inherent thermal stability were investigated in this work. Linear sweep voltammetry (LSV) profiles of the investigated LiTFSI/RTIL electrolytes display much higher oxidative stability compared to the state-of-the-art LiPF 6 /organic carbonate based electrolyte at elevated temperatures. Cycling performance of the LNMO/Li 4 Ti 5 O 12 (LTO) full-cells with LiTFSI/RTIL electrolytes reveals remarkable improvements with respect to capacity retention and Coulombic efficiency. Scanning electron microscopy (SEM) images and X-ray diffraction (XRD) patterns indicate maintained pristine morphology and structure of LNMO particles after 50 cycles at 0.5C. The investigated LiTFSI/RTIL based electrolytes outperform the LiPF 6 /organic carbonate-based electrolyte in terms of cycling performance in LNMO/LTO full-cells at elevated temperatures.

Relation between the ion size and pore size for an electric double-layer capacitor.

PubMed

Largeot, Celine; Portet, Cristelle; Chmiola, John; Taberna, Pierre-Louis; Gogotsi, Yury; Simon, Patrice

2008-03-05

The research on electrochemical double layer capacitors (EDLC), also known as supercapacitors or ultracapacitors, is quickly expanding because their power delivery performance fills the gap between dielectric capacitors and traditional batteries. However, many fundamental questions, such as the relations between the pore size of carbon electrodes, ion size of the electrolyte, and the capacitance have not yet been fully answered. We show that the pore size leading to the maximum double-layer capacitance of a TiC-derived carbon electrode in a solvent-free ethyl-methylimmidazolium-bis(trifluoro-methane-sulfonyl)imide (EMI-TFSI) ionic liquid is roughly equal to the ion size (approximately 0.7 nm). The capacitance values of TiC-CDC produced at 500 degrees C are more than 160 F/g and 85 F/cm(3) at 60 degrees C, while standard activated carbons with larger pores and a broader pore size distribution present capacitance values lower than 100 F/g and 50 F/cm(3) in ionic liquids. A significant drop in capacitance has been observed in pores that were larger or smaller than the ion size by just an angstrom, suggesting that the pore size must be tuned with sub-angstrom accuracy when selecting a carbon/ion couple. This work suggests a general approach to EDLC design leading to the maximum energy density, which has been now proved for both solvated organic salts and solvent-free liquid electrolytes.

The vapour of imidazolium-based ionic liquids: a mass spectrometry study.

PubMed

Deyko, A; Lovelock, K R J; Licence, P; Jones, R G

2011-10-06

Eight common dialkylimidazolium-based ionic liquids have been successfully evaporated in ultra-high vacuum and their vapours analysed by line of sight mass spectrometry using electron ionisation. The ionic liquids investigated were 1-alkyl-3-methylimidazolium bis[(trifluoromethane)sulfonyl]imide, [C(n)C(1)Im][Tf(2)N] (where n = 2, 4, 6, 8), 1-alkyl-3-methylimidazolium tetrafluoroborate, [C(n)C(1)Im][BF(4)] (where n = 4, 8), 1-butyl-3-methylimidazolium octylsulfate, [C(4)C(1)Im][C(8)OSO(3)] and 1-butyl-3-methylimidazolium tetrachloroferrate, [C(4)C(1)Im][FeCl(4)]. All ionic liquids studied here evaporated as neutral ion pairs; no evidence of decomposition products in the vapour phase were observed. Key fragment cations of the ionised vapour of the ionic liquids are identified. The appearance energies, E(app), of the parent cation were measured and used to estimate the ionisation energies, E(i), for the vapour phase neutral ion pairs. Measured ionisation energies ranged from 10.5 eV to 13.0 eV. Using both the identity and E(app) values, the fragmentation pathways for a number of fragment cations are postulated. It will be shown that the enthalpy of vaporisation, Δ(vap)H, can successfully be measured using more than one fragment cation, although caution is required as many fragment cations can also be formed by ionisation of decomposition products.

A Study of Spur Gears Lubricated With Grease-Observations From Seven Experiments

NASA Technical Reports Server (NTRS)

Krantz, Timothy L.; Handschuh, Robert F.

2005-01-01

To improve understanding of gears operating with a perfluoro type space-qualified grease, seven spur gear experiments were performed. Test conditions were selected to study the influences of torque, lubricant type, and atmosphere. Two testing torques provided nominal pitch-line Hertz stresses greater and lesser than the contact stress limit as recommended by the grease manufacturer. As was expected, all tests resulted in some gear tooth wear. Discoloration of the perfluoro type grease occurred for all tests. Tests in dry nitrogen produced some dark-grey colored perfluoro type grease. Testing in either ambient or dry air produced red debris after short test duration, and for tests of longer duration large amounts of red debris, red grease, and wear were evident. Tests using higher torques produced more debris. The first indications of discoloration occurred more quickly with higher test torques. Total amounts of wear were quite significant, up to four times the profile tolerance for AGMA Class 10 gears.

40 CFR 721.983 - Sulfonyl azide intermediate (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

...). 721.983 Section 721.983 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.983 Sulfonyl azide intermediate (generic). (a) Chemical substance and significant new uses...

Highly selective Ba2+ separations with acyclic, lipophilic di-[N-(X)sulfonyl carbamoyl] polyethers.

PubMed

Elshani, Sadik; Chun, Sangki; Amiri-Eliasi, Bijan; Bartsch, Richard A

2005-01-14

New lipophilic acyclic polyethers with two N-(X)sulfonyl carbamoyl groups of "tunable" acidity exhibit remarkable selectivity for Ba2+ over other alkaline earth metal ions in competitive solvent extraction and transport across polymer inclusion membranes.

Synthesis of carbon-11-labeled 5-HT6R antagonists as new candidate PET radioligands for imaging of Alzheimer's disease.

PubMed

Wang, Xiaohong; Dong, Fugui; Miao, Caihong; Li, Wei; Wang, Min; Gao, Mingzhang; Zheng, Qi-Huang; Xu, Zhidong

2018-06-01

Carbon-11-labeled serotonin (5-hydroxytryptamine) 6 receptor (5-HT 6 R) antagonists, 1-[(2-bromophenyl)sulfonyl]-5-[ 11 C]methoxy-3-[(4-methyl-1-piperazinyl)methyl]-1H-indole (O-[ 11 C]2a) and 1-[(2-bromophenyl)sulfonyl]-5-methoxy-3-[(4-[ 11 C]methyl-1-piperazinyl)methyl]-1H-indole (N-[ 11 C]2a), 5-[ 11 C]methoxy-3-((4-methylpiperazin-1-yl)methyl)-1-(phenylsulfonyl)-1H-indole (O-[ 11 C]2b) and 5-methoxy-3-((4-[ 11 C]methylpiperazin-1-yl)methyl)-1-(phenylsulfonyl)-1H-indole (N-[ 11 C]2b), 1-((4-isopropylphenyl)sulfonyl)-5-[ 11 C]methoxy-3-((4-methylpiperazin-1-yl)methyl)-1H-indole (O-[ 11 C]2c) and 1-((4-isopropylphenyl)sulfonyl)-5-methoxy-3-((4-[ 11 C]methylpiperazin-1-yl)methyl)-1H-indole (N-[ 11 C]2c), 1-((4-fluorophenyl)sulfonyl)-5-[ 11 C]methoxy-3-((4-methylpiperazin-1-yl)methyl)-1H-indole (O-[ 11 C]2d) and 1-((4-fluorophenyl)sulfonyl)-5-methoxy-3-((4-[ 11 C]methylpiperazin-1-yl)methyl)-1H-indole (N-[ 11 C]2d), were prepared from their O- or N-desmethylated precursors with [ 11 C]CH 3 OTf through O- or N-[ 11 C]methylation and isolated by HPLC combined with SPE in 40-50% radiochemical yield, based on [ 11 C]CO 2 and decay corrected to end of bombardment (EOB). The radiochemical purity was >99%, and the molar activity (MA) at EOB was 370-740 GBq/μmol with a total synthesis time of ∼40-min from EOB. Copyright © 2018 Elsevier Ltd. All rights reserved.

SEPARATION OF URANIUM HEXAFLUORIDE FROM ORGANIC FLUORO COMPOUNDS

DOEpatents

Libby, W.F.

1958-10-01

A method is presented for removing perfiuoroorganic compounds such as C/ sub 7/F/sub 16/ from UF/sub 6/. The physical and chemical properties of the perfluoro compounds are such as to render their removal from UF/sub 6/ difficulty by conventional techniques. The mixture containing UF/sub 6/ and the perfluoro compounds is pyrolyzed in an inert container at high temperature and pressure. The properties of the products obtained by pyrolysis differ from the properties of UF/sub 6/ to a sufficient degree to render their separation possible by ordinary methods.

High conductivity electrolyte solutions and rechargeable cells incorporating such solutions

DOEpatents

Angell, C.A.; Zhang, S.S.; Xu, K.

1998-10-20

This invention relates generally to electrolyte solvents for use in liquid or rubbery polymer electrolyte solutions as are used, for example, in electrochemical devices. More specifically, this invention relates to sulfonyl/phospho-compound electrolyte solvents and sulfonyl/phospho-compound electrolyte solutions incorporating such solvents. 9 figs.

Platinum(II) diimine complexes with catecholate ligands bearing imide electron-acceptor groups: synthesis, crystal structures, (spectro)electrochemical and EPR studies, and electronic structure.

PubMed

Shavaleev, Nail M; Davies, E Stephen; Adams, Harry; Best, Jonathan; Weinstein, Julia A

2008-03-03

A series of catechols with attached imide functionality (imide = phthalimide PHT, 1,8-naphthalimide NAP, 1,4,5,8-naphthalenediimide NDI, and NAP-NDI) has been synthesized and coordinated to the Pt (II)(bpy*) moiety, yielding Pt(bpy*)(cat-imide) complexes (bpy* = 4,4'-di- tert-butyl-2,2'-bipyridine). X-ray crystal structures of PHT and NAP complexes show a distorted square-planar arrangement of ligands around the Pt center. Both complexes form "head-to-tail" dimers in the solid state through remarkably short unsupported Pt...Pt contacts of 3.208 (PHT) and 3.378 A (NAP). The Pt(bpy*)(cat-imide) complexes are shown to combine optical (absorption) and electrochemical properties of the catecholate (electron-donor) and imide (electron-acceptor) groups. The complexes show a series of reversible reduction processes in the range from -0.5 to -1.9 V vs Fc (+)/Fc, which are centered on either bpy* or imide groups, and a reversible oxidation process at +0.07 to +0.14 V, which is centered on the catecholate moiety. A combination of UV-vis absorption spectroscopy, cyclic voltammetry, UV-vis spectroelectrochemistry, and EPR spectroscopy has allowed assignment of the nature of frontier orbitals in Pt(bpy*)(cat-imide) complexes. The HOMO in Pt(bpy*)(cat-imide) is centered on the catechol ligand, while the LUMO is localized either on bpy* or on the imide group, depending on the nature of the imide group involved. Despite the variations in the nature of the LUMO, the lowest-detectable electronic transition in all Pt(bpy*)(cat-imide) complexes has predominantly ligand-to-ligand (catechol-to-diimine) charge-transfer nature (LLCT) and involves a bpy*-based unoccupied molecular orbital in all cases. The LLCT transition in all Pt(bpy*)(cat-imide) complexes appears at 530 nm in CH2Cl2 and is strongly negatively solvatochromic. The energy of this transition is remarkably insensitive to the imide group present, indicating lack of electronic communication between the imide and the catechol moieties within the cat-imide ligand. The high extinction coefficient, approximately 6 x 10(3) L mol(-1) cm(-1) of this predominantly LLCT transition is the result of the Pt orbital contribution, as revealed by EPR spectroscopy of the complexes in various redox states. The CV profile of the oxidation process of Pt(bpy*)(cat-imide) in CH2Cl2 and DMF is concentration dependent, as was shown for NDI and PHT complexes as typical examples. Oxidation appears as a simple diffusion-limited process at low concentrations, with an increasing anodic-to-cathodic peak separation eventually resolving as two independent consecutive waves as the concentration of the complex increases. It is suggested that aggregation of the complexes in the diffusion layer in the course of oxidation is responsible for the observed concentration dependence. Overall, the Pt(bpy*)(cat-imide) complexes are electrochromic compounds in which a series of stepwise reversible redox processes in the potential range from 0.2 to -2 V (vs Fc (+)/Fc) leads to tuneable absorbencies between 300 and 850 nm.

One-pot synthesis of 2,5-dihydropyrroles from terminal alkynes, azides, and propargylic alcohols by relay actions of copper, rhodium, and gold.

PubMed

Miura, Tomoya; Tanaka, Takamasa; Matsumoto, Kohei; Murakami, Masahiro

2014-12-01

Relay actions of copper, rhodium, and gold formulate a one-pot multistep pathway, which directly gives 2,5-dihydropyrroles starting from terminal alkynes, sulfonyl azides, and propargylic alcohols. Initially, copper-catalyzed 1,3-dipolar cycloaddition of terminal alkynes with sulfonyl azides affords 1-sulfonyl-1,2,3-triazoles, which then react with propargylic alcohols under the catalysis of rhodium. The resulting alkenyl propargyl ethers subsequently undergo the thermal Claisen rearrangement to give α-allenyl-α-amino ketones. Finally, a gold catalyst prompts 5-endo cyclization to produce 2,5-dihydropyrroles. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Proteasome inhibition by new dual warhead containing peptido vinyl sulfonyl fluorides.

PubMed

Brouwer, Arwin J; Herrero Álvarez, Natalia; Ciaffoni, Adriano; van de Langemheen, Helmus; Liskamp, Rob M J

2016-08-15

The success of inhibition of the proteasome by formation of covalent bonds is a major victory over the long held-view that this would lead to binding the wrong targets and undoubtedly lead to toxicity. Great challenges are now found in uncovering ensembles of new moieties capable of forming long lasting ties. We have introduced peptido sulfonyl fluorides for this purpose. Tuning the reactivity of this electrophilic trap may be crucial for modulating the biological action. Here we describe incorporation of a vinyl moiety into a peptido sulfonyl fluoride backbone, which should lead to a combined attack of the proteasome active site threonine on the double bond and the sulfonyl fluoride. Although this led to strong proteasome inhibitors, in vitro studies did not unambiguously demonstrate the formation of the proposed seven-membered ring structure. Possibly, formation of a seven-membered covalent adduct with the proteosomal active site threonine can only be achieved within the context of the enzyme. Nevertheless, this dual warhead concept may provide exclusive possibilities for duration and selectivity of proteasome inhibition. Copyright © 2016 Elsevier Ltd. All rights reserved.

Diastereoselective addition of Grignard reagents to α-epoxy N-sulfonyl hydrazones

NASA Astrophysics Data System (ADS)

Uteuliyev, Maulen M.; Nguyen, Thien T.; Coltart, Don M.

2015-12-01

The α-alkylation of ketones and their derivatives by the addition of their corresponding enolates to alkyl halides is a fundamental synthetic transformation, but its utility is limited because the key bond-forming step proceeds in a bimolecular nucleophilic substitution fashion. Here we describe how an umpolung strategy that involves the addition of Grignard reagents to α-epoxy N-sulfonyl hydrazones—directed by the alkoxide of the 1-azo-3-alkoxy propenes formed in situ via base-induced ring opening of the epoxide—leads to the syn-selective production of α-alkyl-β-hydroxy N-sulfonyl hydrazones with α-quaternary centres. This transformation is remarkable in its ability to incorporate an unprecedented range of carbon-based substituents, which include primary, secondary and tertiary alkyl, as well as alkenyl, aryl, allenyl and alkynyl groups. Subsequent hydrolysis of the β-hydroxy N-sulfonyl hydrazone products produces the corresponding β-hydroxy ketones. In addition to hydrolysis, the hydrazone products are poised to undergo numerous different known synthetic transformations via well-established chemistry, which would provide access to a wide array of useful structures.

Evaluating the impact of two training interventions to improve diagnosis and case-management of malaria and pneumonia in Uganda.

PubMed

Ssebuliba, D M; Ouifki, R; Pretorius, C; Burnett, S M; Mbonye, M K; Naikoba, S; Willis, K; Weaver, M R

2017-01-01

We present an age-structured mathematical model of malaria and pneumonia to study the effect of two capacity-building interventions: Integrated Management of Infectious Diseases (IMID) and On-site Support Services (OSS). IMID leads to a reduction in malaria prevalence by more than 2·4% across the [0,5), [5,14) and [14,50) age groups. IMID + OSS reduces it by more than 16·0% across all age groups. IMID decreases pneumonia prevalence by more than 3·0% across all age groups while IMID + OSS decreases it by more than 1·0% across all age groups. The number of malaria and pneumonia deaths is reduced by 7·8% by IMID across all age groups and IMID + OSS decreases this number by 30·5% across all age groups, which translates to saving a life of a child per month. Prevalence of malaria-pneumonia for the [0,5) age group is 0·52% at baseline, and IMID and IMID + OSS reduce it by 6·6% and 23·6%, respectively. There is no change in incidence of malaria or pneumonia disease episodes. The results also indicate that triaging of children contributes more than 50% to the effect of the interventions in reduction of deaths and a range of 14-91% in reduction of disease cases.

A short synthesis and biological evaluation of potent and nontoxic antimalarial bridged bicyclic beta-sulfonyl-endoperoxides.

PubMed

Bachi, Mario D; Korshin, Edward E; Hoos, Roland; Szpilman, Alex M; Ploypradith, Poonsakdi; Xie, Suji; Shapiro, Theresa A; Posner, Gary H

2003-06-05

The syntheses and in vitro antimalarial screening of 50 bridged, bicyclic endoperoxides of types 9-13 are reported. In contrast to antimalarial trioxanes of the artemisinin family, but like yingzhaosu A and arteflene, the peroxide function of compounds 9-13 is contained in a 2,3-dioxabicyclo[3.3.1]nonane system 6. Peroxides 9 and 10 (R(1) = OH) are readily available through a multicomponent, sequential, free-radical reaction involving thiol-monoterpenes co-oxygenation (a TOCO reaction). beta-Sulfenyl peroxides 9 and 10 (R(1) = OH) are converted into beta-sulfinyl and beta-sulfonyl peroxides of types 11-13 by controlled S-oxidation and manipulation of the tert-hydroxyl group through acylation, alkylation, or dehydration followed by selective hydrogenation. Ten enantiopure beta-sulfonyl peroxides of types 12 and 13 exhibit in vitro antimalarial activity comparable to that of artemisinin (IC(50) = 6-24 nM against Plasmodium falciparum NF54). In vivo testing of a few selected peroxides against Plasmodium berghei N indicates that the antimalarial efficacies of beta-sulfonyl peroxides 39a, 46a, 46b, and 50a are comparable to those of some of the best antimalarial drugs and are higher than artemisinin against chloroquine-resistant Plasmodium yoelii ssp. NS. In view of the nontoxicity of beta-sulfonyl peroxides 39a, 46a, and 46b in mice, at high dosing, these compounds are regarded as promising antimalarial drug candidates.

Sympathetic Nerve Hyperactivity in the Spleen: Causal for Nonpathogenic-Driven Chronic Immune-Mediated Inflammatory Diseases (IMIDs)?

PubMed

Bellinger, Denise L; Lorton, Dianne

2018-04-13

Immune-Mediated Inflammatory Diseases (IMIDs) is a descriptive term coined for an eclectic group of diseases or conditions that share common inflammatory pathways, and for which there is no definitive etiology. IMIDs affect the elderly most severely, with many older individuals having two or more IMIDs. These diseases include, but are not limited to, type-1 diabetes, obesity, hypertension, chronic pulmonary disease, coronary heart disease, inflammatory bowel disease, and autoimmunity, such as rheumatoid arthritis (RA), Sjőgren's syndrome, systemic lupus erythematosus, psoriasis, psoriatic arthritis, and multiple sclerosis. These diseases are ostensibly unrelated mechanistically, but increase in frequency with age and share chronic systemic inflammation, implicating major roles for the spleen. Chronic systemic and regional inflammation underlies the disease manifestations of IMIDs. Regional inflammation and immune dysfunction promotes targeted end organ tissue damage, whereas systemic inflammation increases morbidity and mortality by affecting multiple organ systems. Chronic inflammation and skewed dysregulated cell-mediated immune responses drive many of these age-related medical disorders. IMIDs are commonly autoimmune-mediated or suspected to be autoimmune diseases. Another shared feature is dysregulation of the autonomic nervous system and hypothalamic pituitary adrenal (HPA) axis. Here, we focus on dysautonomia. In many IMIDs, dysautonomia manifests as an imbalance in activity/reactivity of the sympathetic and parasympathetic divisions of the autonomic nervous system (ANS). These major autonomic pathways are essential for allostasis of the immune system, and regulating inflammatory processes and innate and adaptive immunity. Pathology in ANS is a hallmark and causal feature of all IMIDs. Chronic systemic inflammation comorbid with stress pathway dysregulation implicate neural-immune cross-talk in the etiology and pathophysiology of IMIDs. Using a rodent model of inflammatory arthritis as an IMID model, we report disease-specific maladaptive changes in β₂-adrenergic receptor (AR) signaling from protein kinase A (PKA) to mitogen activated protein kinase (MAPK) pathways in the spleen. Beta₂-AR signal "shutdown" in the spleen and switching from PKA to G-coupled protein receptor kinase (GRK) pathways in lymph node cells drives inflammation and disease advancement. Based on these findings and the existing literature in other IMIDs, we present and discuss relevant literature that support the hypothesis that unresolvable immune stimulation from chronic inflammation leads to a maladaptive disease-inducing and perpetuating sympathetic response in an attempt to maintain allostasis. Since the role of sympathetic dysfunction in IMIDs is best studied in RA and rodent models of RA, this IMID is the primary one used to evaluate data relevant to our hypothesis. Here, we review the relevant literature and discuss sympathetic dysfunction as a significant contributor to the pathophysiology of IMIDs, and then discuss a novel target for treatment. Based on our findings in inflammatory arthritis and our understanding of common inflammatory process that are used by the immune system across all IMIDs, novel strategies to restore SNS homeostasis are expected to provide safe, cost-effective approaches to treat IMIDs, lower comorbidities, and increase longevity.

21 CFR 177.2450 - Polyamide-imide resins.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) For the purpose of this section the polyamide-imide resins are derived from the condensation reaction...) The polyamide-imide resins (CAS Reg. No. 31957-38-7) derived from the condensation reaction of...

21 CFR 177.2450 - Polyamide-imide resins.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) For the purpose of this section the polyamide-imide resins are derived from the condensation reaction...) The polyamide-imide resins (CAS Reg. No. 31957-38-7) derived from the condensation reaction of...

Ring Expansion and Rearrangements of Rhodium(II) Azavinyl Carbenes

PubMed Central

Selander, Nicklas; Worrell, Brady T.

2013-01-01

An efficient, regioselective and convergent method for the ring expansion and rearrangement of 1-sulfonyl-1,2,3-triazoles under rhodium(II)-catalyzed conditions is described. These denitrogenative reactions form substituted enaminone and olefin-based products, which in the former case can be further functionalized to unique products rendering the sulfonyl triazole traceless. PMID:23161725

40 CFR 721.1637 - 1,2-Propanediol, 3-(2-propenyloxy)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false 1,2-Propanediol, 3-(2-propenyloxy)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy]-3-(2...)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy]-3-(2...

40 CFR 721.1637 - 1,2-Propanediol, 3-(2-propenyloxy)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1,2-Propanediol, 3-(2-propenyloxy)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy]-3-(2...)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy]-3-(2...

Aqueous Exfoliation of Graphite into Graphene Assisted by Sulfonyl Graphene Quantum Dots for Photonic Crystal Applications.

PubMed

Zeng, Minxiang; Shah, Smit A; Huang, Dali; Parviz, Dorsa; Yu, Yi-Hsien; Wang, Xuezhen; Green, Micah J; Cheng, Zhengdong

2017-09-13

We investigate the π-π stacking of polyaromatic hydrocarbons (PAHs) with graphene surfaces, showing that such interactions are general across a wide range of PAH sizes and species, including graphene quantum dots. We synthesized a series of graphene quantum dots with sulfonyl, amino, and carboxylic functional groups and employed them to exfoliate and disperse pristine graphene in water. We observed that sulfonyl-functionalized graphene quantum dots were able to stabilize the highest concentration of graphene in comparison to other functional groups; this is consistent with prior findings by pyrene. The graphene nanosheets prepared showed excellent colloidal stability, indicating great potential for applications in electronics, solar cells, and photonic displays which was demonstrated in this work.

Role of Dispersive Fluorous Interaction in the Solvation Dynamics of the Perfluoro Group Containing Molecules.

PubMed

Mondal, Saptarsi; Chaterjee, Soumit; Halder, Ritaban; Jana, Biman; Singh, Prashant Chandra

2017-08-17

Perfluoro group containing molecules possess an important self-aggregation property through the fluorous (F···F) interaction which makes them useful for diverse applications such as medicinal chemistry, separation techniques, polymer technology, and biology. In this article, we have investigated the solvation dynamics of coumarin-153 (C153) and coumarin-6H (C6H) in ethanol (ETH), 2-fluoroethanol (MFE), and 2,2,2-trifluoroethanol (TFE) using the femtosecond upconversion technique and molecular dynamics (MD) simulation to understand the role of fluorous interaction between the solute and solvent molecules in the solvation dynamics of perfluoro group containing molecules. The femtosecond upconversion data show that the time scales of solvation dynamics of C6H in ETH, MFE, and TFE are approximately the same whereas the solvation dynamics of C153 in TFE is slow as compared to that of ETH and MFE. It has also been observed that the time scale of solvation dynamics of C6H in ETH and MFE is higher than that of C153 in the same solvents. MD simulation results show a qualitative agreement with the experimental data in terms of the time scale of the slow components of the solvation for all the systems. The experimental and simulation studies combined lead to the conclusion that the solvation dynamics of C6H in all solvents as well as C153 in ETH and MFE is mostly governed by the charge distribution of ester moieties (C═O and O) of dye molecules whereas the solvation of C153 in TFE is predominantly due to the dispersive fluorous interaction (F···F) between the perfluoro groups of the C153 and solvent molecules.

Surface Enrichment in Equimolar Mixtures of Non-Functionalized and Functionalized Imidazolium-Based Ionic Liquids.

PubMed

Heller, Bettina S J; Kolbeck, Claudia; Niedermaier, Inga; Dommer, Sabine; Schatz, Jürgen; Hunt, Patricia; Maier, Florian; Steinrück, Hans-Peter

2018-04-12

For equimolar mixtures of ionic liquids with imidazolium-based cations of very different electronic structure, we observe very pronounced surface enrichment effects by angle-resolved X-ray photoelectron spectroscopy (XPS). For a mixture with the same anion, that is, 1-methyl-3-octylimidazolium hexafluorophosphate+1,3-di(methoxy)imidazolium hexafluorophosphate ([C 8 C 1 Im][PF 6 ]+[(MeO) 2 Im][PF 6 ]), we find a strong enrichment of the octyl chain-containing [C 8 C 1 Im] + cation and a corresponding depletion of the [(MeO) 2 Im] + cation in the topmost layer. For a mixture with different cations and anions, that is, [C 8 C 1 Im][Tf 2 N]+[(MeO) 2 Im][PF 6 ], we find both surface enrichment of the [C 8 C 1 Im] + cation and the [Tf 2 N] - (bis[(trifluoromethyl)sulfonyl]imide) anion, while [(MeO) 2 Im] + and [PF 6 ] - are depleted from the surface. We propose that the observed behavior in these mixtures is due to a lowering of the surface tension by the enriched components. Interestingly, we observe pronounced differences in the chemical shifts of the imidazolium ring signals of the [(MeO) 2 Im] + cations as compared to the non-functionalized cations. Calculations of the electronic structure and the intramolecular partial charge distribution of the cations contribute to interpreting these shifts for the two different cations. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Improvement of the cloud point extraction of uranyl ions by the addition of ionic liquids.

PubMed

Gao, Song; Sun, Taoxiang; Chen, Qingde; Shen, Xinghai

2013-12-15

The cloud point extraction (CPE) of uranyl ions by different kinds of extractants in Triton X-114 (TX-114) micellar solution was investigated upon the addition of ionic liquids (ILs) with various anions, i.e., bromide (Br(-)), tetrafluoroborate (BF4(-)), hexafluorophosphate (PF6(-)) and bis[(trifluoromethyl)sulfonyl]imide (NTf2(-)). A significant increase of the extraction efficiency was found on the addition of NTf2(-) based ILs when using neutral extractant tri-octylphosphine oxide (TOPO), and the extraction efficiency kept high at both nearly neutral and high acidity. However, the CPE with acidic extractants, e.g., bis(2-ethylhexyl) phosphoric acid (HDEHP) and 8-hydroxyquinoline (8-HQ) which are only effective at nearly neutral condition, was not improved by ILs. The results of zeta potential and (19)F NMR measurements indicated that the anion NTf2(-) penetrated into the TX-114 micelles and was enriched in the surfactant-rich phase during the CPE process. Meanwhile, NTf2(-) may act as a counterion in the CPE of UO2(2+) by TOPO. Furthermore, the addition of IL increased the separation factor of UO2(2+) and La(3+), which implied that in the micelle TOPO, NTf2(-) and NO3(-) established a soft template for UO2(2+). Therefore, the combination of CPE and IL provided a supramolecular recognition to concentrate UO2(2+) efficiently and selectively. Copyright © 2013 Elsevier B.V. All rights reserved.

Harvesting polysulfides by sealing the sulfur electrode in a composite ion-selective net

NASA Astrophysics Data System (ADS)

Chen, Yazhou; Li, Zhong; Li, Xuekui; Zeng, Danli; Xu, Guodong; Zhang, Yunfeng; Sun, Yubao; Ke, Hanzhong; Cheng, Hansong

2017-11-01

A cathode was prepared by sealing a carbon supported sulfur electrode inside a composite ion-selective net made of carbon, binder and lithiated ionomer to restrict shuttling of polysulfide anionic species. As a result, the soluble polysulfide anions become unable to escape from the composite ion-selective films due to the electrostatic repulsion between the immobilized single ion conducting ionomers and the polysulfides with no dead angles. Experimentally, lithiated 4,4‧-difluoro bis(benzene sulfonyl)imide and PEG200 were copolymerized to form a polyether based single ion conducting polymer. The ionic conductivity of the blend film made of ionomer and poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) at a mass ratio of 1:1 is 0.57 mS cm-1 at room temperature. The battery capacity with the sealed sulfur electrode is 1412 mAh g-1 at 0.5 C, 1041 mAh g-1 at 1.0 C, 873 mAh g-1 at 2.0 C and 614 mAh g-1 at 5.0 C, significantly better than the results with lithiated Nafion especially at high C rates. In addition, a long cycling test at 2 C for 500 cycles gives rise to a stable capacity of 800 mAh g-1. The intrinsic electrostatic repulsion between polysulfide anions and the negatively charged electrolyte film, together with the overall sealed electrode configuration, is responsible for blocking the shuttling of polysulfides effectively.

Investigation of the interactions between 1-butyl-3-methylimidazolium-based ionic liquids and isobutylene using density functional theory.

PubMed

Li, Xiaoning; Guo, Wenli; Wu, Yibo; Li, Wei; Gong, Liangfa; Zhang, Xiaoqian; Li, Shuxin; Shang, Yuwei; Yang, Dan; Wang, Hao

2018-03-06

To identify ionic liquids (ILs) that could be used as solvents in isobutylene (IB) polymerization, the interactions between IB and eight different ILs based on the 1-butyl-3-methylimidazolium cation ([Bmim] + ) were investigated using density functional theory (DFT). The anions in the ILs were chloride, hexafluorophosphate, tetrafluoroborate, bis[(trifluoromethyl)sulfonyl]imide, tetrachloroaluminate ([AlCl 4 ] - ), tetrachloroferrate, acetate, and trifluoroacetate. The interaction geometries were explained by changes in the total energy, intermolecular distances, Hirshfeld charges, and the electrostatic potential surface. The IL solvents were screened by comparing their interaction intensities with IB to the interaction intensities of reference ILs ([AlCl 4 ] - -based ILs) with IB. The microscopic mechanism for IB dissolution was rationalized by invoking a previously reported microscopic mechanism for the dissolution of gases in ILs. Computation results revealed that hydrogen (H) bonding between C2-H on the imidazolium ring and the anions plays a key role in ion pair (IP) formation. The addition of IB leads to slight changes in the dominant interactions of the IP. IB molecules occupied cavities created by small angular rearrangements of the anions, just as CO 2 does when it is dissolved in an IL. The limited total free space in the ILs and the much larger size of IB than CO 2 were found to be responsible for the poor solubility of IB compared with that of CO 2 in the ILs.

Mechanism of immunomodulatory drugs' action in the treatment of multiple myeloma

PubMed Central

Chang, Xiubao; Zhu, Yuanxiao; Shi, Changxin; Stewart, A. Keith

2014-01-01

Although immunomodulatory drugs (IMiDs), such as thalidomide, lenalidomide, and pomalidomide, are widely used in the treatment of multiple myeloma (MM), the molecular mechanism of IMiDs' action is largely unknown. In this review, we will summarize recent advances in the application of IMiDs in MM cancer treatment as well as their effects on immunomodulatory activities, anti-angiogenic activities, intervention of cell surface adhesion molecules between myeloma cells and bone marrow stromal cells, anti-inflammatory activities, anti-proliferation, pro-apoptotic effects, cell cycle arrest, and inhibition of cell migration and metastasis. In addition, the potential IMiDs' target protein, IMiDs' target protein's functional role, and the potential molecular mechanisms of IMiDs resistance will be discussed. We wish, by presentation of our naive discussion, that this review article will facilitate further investigation in these fields. PMID:24374776

Phosphorus-containing imide resins

NASA Technical Reports Server (NTRS)

Varma, I. K.; Fohlen, G. M.; Parker, J. A. (Inventor)

1984-01-01

Flame-resistant reinforced bodies are disclosed which are composed of reinforcing fibers, filaments or fabrics in a cured body of bis- and tris-imide resins derived from tris(m-aminophenyl) phosphine oxides by reaction with maleic anhydride or its derivatives, or of addition polymers of such imides, including a variant in which a mono-imide is condensed with a dianhydride and the product is treated with a further quantity of maleic anhydride.

Preparation of Imide Oligomers via Concurrent Reactive Extrusion

NASA Technical Reports Server (NTRS)

Avakian, Roger W. (Inventor); Hu, Ling (Inventor)

2018-01-01

Reactive extrusion can be used in a continuous, solvent-less preparation of imide oligomers involving two competing reactions among three ingredients, the first reaction between a dianhydride and a diamine and the second reaction between an endcap and the same diamine. The imide oligomer can form a composite via conventional production methods or via formation of a film from imide oligomer re-melted in an extruder before being impregnated into tape or fabric.

Anisotropic Copoly(Imide Oxetane) Coatings and Articles of Manufacture, Copoly(Imide Oxetane)s Containing Pendant Fluorocarbon Moieties, Oligomers and Processes Therefor

NASA Technical Reports Server (NTRS)

Wohl, Christopher J. (Inventor); Siochi, Emilie J. (Inventor); Smith, Joseph G. (Inventor); Connell, John W. (Inventor)

2017-01-01

Copoly(imide oxetane) materials are disclosed that can exhibit a low surface energy while possessing the mechanical, thermal, chemical and optical properties associated with polyimides. The copoly(imide oxetane)s are prepared using a minor amount of fluorinated oxetane-derived oligomer with sufficient fluorine-containing segments of the copoly(imide oxetane)s that migrate to the exterior surface of the polymeric material to yield low surface energies. Thus the coatings and articles of manufacture made with the copoly(imide oxetane)s of this invention are characterized as having an anisotropic fluorine composition. The low surface energies can be achieved with very low content of fluorinated oxetane-derived oligomer. The copolymers of this invention can enhance the viability of polyimides for many applications and may be acceptable where homopolyimide materials have been unacceptable.

Purification and thermal analysis of perfluoro-n-alkanoic acids.

PubMed

Tsuji, Minami; Inoue, Tohru; Shibata, Osamu

2008-01-15

Purification of perfluoro-n-alkanoic acids (C(n)F(2n+1)COOH, n=7, 9, 11, 13, 15 and 17) was made by repeated recrystallizations from n-hexane/acetone mixed solvent, and their purity was found to be more than 99.5% by GC-MS, NMR, and elemental analysis. The thermal behaviors such as melting point and enthalpy change of fusion were investigated using differential scanning calorimetry (DSC). The melting point monotonously increased with increasing carbon number (n) of the acids, while the enthalpy change showed irregularity at n=14. The crystal structure of these acids was found to be dependent upon solvent used for recrystallization; that is, the acids recrystallized from the above solvent becomes more stable energetically, indicating their higher enthalpy change of fusion than that of the solidified acids from fused ones. The solid state was also found to vary depending upon the thermal history, indicating that a few crystal structures of the solid state are quite similar energetically. The melting points (T(m)) of perfluoro-n-alkanoic acids are higher than those of corresponding n-alkanoic acids, and the difference in T(m) increases with increasing carbon number in the acids.

21 CFR 176.160 - Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine. 176.160 Section 176.160 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: PAPER AND PAPERBOARD COMPONENTS...

21 CFR 176.160 - Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine. 176.160 Section 176.160 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: PAPER AND PAPERBOARD COMPONENTS...

21 CFR 176.160 - Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine. 176.160 Section 176.160 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: PAPER AND PAPERBOARD COMPONENTS...

21 CFR 176.160 - Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine. 176.160 Section 176.160 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: PAPER AND PAPERBOARD COMPONENTS...

40 CFR 721.1630 - 1,2-Ethanediol bis(4-methylbenzenesulfonate); 2,2-oxybis-ethane bis(4-methylbenzenesulfonate...

Code of Federal Regulations, 2011 CFR

2011-07-01

... sulfonate); and ethanol, 2-[1-[[2-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy] ethoxy]methyl]-2-(2-propenyloxy... sulfonate); and ethanol, 2-[1-[[2-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy] ethoxy]methyl]-2-(2-propenyloxy...,2′-[oxybis(2,1-ethanediyloxy)]bis-, bis(4-methylbenzene-sulfonate) (PMN P-93-1195, CAS no. 19249-03...

40 CFR 721.1630 - 1,2-Ethanediol bis(4-methylbenzenesulfonate); 2,2-oxybis-ethane bis(4-methylbenzenesulfonate...

Code of Federal Regulations, 2010 CFR

2010-07-01

... sulfonate); and ethanol, 2-[1-[[2-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy] ethoxy]methyl]-2-(2-propenyloxy... sulfonate); and ethanol, 2-[1-[[2-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy] ethoxy]methyl]-2-(2-propenyloxy...,2′-[oxybis(2,1-ethanediyloxy)]bis-, bis(4-methylbenzene-sulfonate) (PMN P-93-1195, CAS no. 19249-03...

Phosphorescent Iridium(III) Complexes Bearing Fluorinated Aromatic Sulfonyl Group with Nearly Unity Phosphorescent Quantum Yields and Outstanding Electroluminescent Properties.

PubMed

Zhao, Jiang; Yu, Yue; Yang, Xiaolong; Yan, Xiaogang; Zhang, Huiming; Xu, Xianbin; Zhou, Guijiang; Wu, Zhaoxin; Ren, Yixia; Wong, Wai-Yeung

2015-11-11

A series of heteroleptic functional Ir(III) complexes bearing different fluorinated aromatic sulfonyl groups has been synthesized. Their photophysical features, electrochemical behaviors, and electroluminescent (EL) properties have been characterized in detail. These complexes emit intense yellow phosphorescence with exceptionally high quantum yields (ΦP > 0.9) at room temperature, and the emission maxima of these complexes can be finely tuned depending upon the number of the fluorine substituents on the pendant phenyl ring of the sulfonyl group. Furthermore, the electrochemical properties and electron injection/transporting (EI/ET) abilities of these Ir(III) phosphors can also be effectively tuned by the fluorinated aromatic sulfonyl group to furnish some desired characters for enhancing the EL performance. Hence, the maximum luminance efficiency (ηL) of 81.2 cd A(-1), corresponding to power efficiency (ηP) of 64.5 lm W(-1) and external quantum efficiency (ηext) of 19.3%, has been achieved, indicating the great potential of these novel phosphors in the field of organic light-emitting diodes (OLEDs). Furthermore, a clear picture has been drawn for the relationship between their optoelectronic properties and chemical structures. These results should provide important information for developing highly efficient phosphors.

Iridium-mediated isomerization-cyclization of bicyclic Pauson-Khand derived allylic alcohols.

PubMed

Kavanagh, Yvonne; Chaney, Cíara M; Muldoon, Jimmy; Evans, Paul

2008-11-07

Treatment of 2-(toluene-4-sulfonyl)-2,3,4,4a,5,6-hexahydro-1H-[2]pyrindin-6-ol 10, accessed from the diastereoselective Luche reduction of a Pauson-Khand derived bicylic cyclopentenone, with a catalytic amount of (1,5-cyclooctadiene)(pyridine)(tricyclohexylphosphine)iridium(I) hexafluorophosphate 1 (Crabtree's catalyst) under a hydrogen atmosphere resulted in the formation of 4-(toluene-4-sulfonyl)-2-oxa-4-azatricyclo[5.2.1.0(3,8)]decane 12 as a single diastereoisomer. This process is likely to proceed via an initial Ir(I)-mediated isomerization of the alkene to form an N-sulfonyl enamine 11, followed by cyclization. Evidence to support this came when, after short reaction periods, 11 was isolated, characterized spectroscopically, and on resubmission to the reaction conditions formed 12.

4-N-Hydroxy-4-[1-(sulfonyl)piperidin-4-yl]-butyramides as HDAC inhibitors.

PubMed

Rossi, Cristina; Fincham, Christopher I; D'Andrea, Piero; Porcelloni, Marina; Ettorre, Alessandro; Mauro, Sandro; Bigioni, Mario; Binaschi, Monica; Maggi, Carlo A; Nardelli, Federica; Parlani, Massimo; Fattori, Daniela

2011-11-15

A series of N-substituted 4-alkylpiperidine hydroxamic acids, corresponding to the basic structure of histone deacetylase (HDAC) inhibitors (zinc binding moiety-linker-capping group) has been previously reported by our group. Linker length and aromatic capping group connection were systematically varied to find the optimal geometric parameters. A new series of submicromolar inhibitors was thus identified, which showed antiproliferative activity on HCT-116 colon carcinoma cells. We report here the second part of the strategy used in our research group to find a new class of HDAC inhibitors, namely the SAR study for the compounds bearing a sulfonyl group on the piperidine nitrogen. In the present work, we have considered both sulfonamides and sulfonyl ureas. Copyright © 2011 Elsevier Ltd. All rights reserved.

Process for preparing phthalocyanine polymer from imide containing bisphthalonitrile

NASA Technical Reports Server (NTRS)

Achar, Bappalige N. (Inventor); Fohlen, George M. (Inventor); Parker, John A. (Inventor)

1987-01-01

Imide-linked bisphthalonitrile compounds are prepared by combining a dicyano aromatic diamine and an organic dianhydride to produce an amic acid linked bisphthalonitrile compound. The amic acid linked bisphthalonitrile compound is dehydrocyclized to produce the imide-linked bisphthalonitrile compounds. The imide-linked bisphthalonitrile compounds may be polymerized to produce a phythalocyanine polymer by heating the imide-linked bisphthalonitrile compound, either alone or in the presence of a metal powder or a metal salt. These compounds are useful in the coating, laminating and molding arts. The polymers are useful in composite matrix resins where increased fire resistance, toughness and resistance to moisture are required, particularly as secondary structures in aircraft and spacecraft.

40 CFR 721.9582 - Certain perfluoroalkyl sulfonates.

Code of Federal Regulations, 2014 CFR

2014-07-01

...[(heptadecafluorooctyl)sulfonyl]amino]ethyl]-.omega.-hydroxy- 29457-72-5 1-Octanesulfonic acid, 1,1,2,2,3,3,4,4,5,5,6,6,7...-octanethiol and .alpha.-(1-oxo-2-propenyl)-.omega.-methoxypoly(oxy-1,2-ethanediyl) 68891-96-3 Chromium...[(heptadecafluorooctyl)sulfonyl]amino]ethyl]-.omega.-methoxy- 70225-14-8 1-Octanesulfonic acid, 1,1,2,2,3,3,4,4,5,5,6,6,7...

21 CFR 176.160 - Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Chromium (Cr III) complex of N-ethyl-N-heptadecylfluoro-octane sulfonyl glycine. 176.160 Section 176.160 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) INDIRECT FOOD ADDITIVES: PAPER AND PAPERBOARD COMPONENTS Substances for Use Only as Components of...

Phenylethynyl terminated imide oligomers

NASA Technical Reports Server (NTRS)

Hergenrother, Paul M. (Inventor); Bryant, Robert G. (Inventor); Jensen, Brian J. (Inventor); Havens, Stephen J. (Inventor)

1994-01-01

Four phenylethynyl amine compounds - 3 and 4-aminophenoxy-4'-phenylethynylbenzophenone, and 3 and 4-amino-4'-phenylethynylbenzophenone - were readily prepared and were used to endcap imide oligomers. Phenylethynyl-terminated amide acid oligomers and phenylethynyl-terminated imide oligomers with various molecular weights and compositions were prepared and characterized. These oligomers were cured at 300 to 400 C to provide crosslinked polyimides with excellent solvent resistance, high strength and modulus, and good high temperature properties. Adhesive panels, composites, films, and moldings from these phenylethynyl terminated imide oligomers gave excellent mechanical performance.

Phenylethynyl terminated imide oligomers

NASA Technical Reports Server (NTRS)

Hergenrother, Paul M. (Inventor); Bryant, Robert G. (Inventor); Jensen, Brian J. (Inventor); Havens, Stephen J. (Inventor)

1995-01-01

Four phenylethynyl amine compounds - 3 and 4-aminophenoxy-4'-phenylethynylbenzophenone, and 3 and 4-amino-4'-phenylethynylbenzophenone - were readily prepared and were used to endcap imide oligomers. Phenylethynyl-terminated amide acid oligomers and phenylethynyl-terminated imide oligomers with various molecular weights and compositions were prepared and characterized. These oligomers were cured at 300 to 400 C to provide crosslinked polyimides with excellent solvent resistance, high strength and modulus, and good high temperature properties. Adhesive panels, composites, films, and moldings from these phenylethynyl terminated imide oligomers gave excellent mechanical performance.

Poly(imide-siloxane) segmented copolymer structural adhesives prepared by bulk and solution thermal imidization

NASA Technical Reports Server (NTRS)

Bott, R. H.; Summers, J. D.; Arnold, C. A.; Blankenship, C. P., Jr.; Taylor, L. T.

1988-01-01

The improved properties that have been demonstrated through thermal solution imidization in the case of polyimides and poly(imide-siloxane) segmented copolymers suggests significant potential for application of these new materials. Specifically, the enhancement in solubility, moisture reduction, and processability observed through this solution technique is quite dramatic. Previous work has shown that the presence of low amounts of siloxane does not detract significantly from the lap shear strength of these materials to titanium in the case of bulk thermal imidization synthesis. In addition, the siloxane incorporation results in the added advantage of resistance to hot, wet environments. This added durability is presumably due to the hydrophobic siloxane segments preventing the uptake of water at the critical interphase between the adhesive and the adherend. This paper discusses the extension of this work to the solution imidization synthesis technique recently developed in our laboratory. Results dealing with the absolute bond strengths as well as durability and failure surface analysis will be presented.

Imide/arylene ether block copolymers

NASA Technical Reports Server (NTRS)

Jensen, B. J.; Hergenrother, P. M.; Bass, R. G.

1991-01-01

Two series of imide/arylene either block copolymers were prepared using an arylene ether block and either an amorphous or semi-crystalline imide block. The resulting copolymers were characterized and selected physical and mechanical properties were determined. These results, as well as comparisons to the homopolymer properties, are discussed.

Sulfonyl chlorides as an efficient tool for the postsynthetic modification of Cr-MIL-101-SO3H and CAU-1-NH2.

PubMed

Klinkebiel, Arne; Reimer, Nele; Lammert, Martin; Stock, Norbert; Lüning, Ulrich

2014-08-25

Postsynthetic modification can be used to introduce sulfonamide functionalities into MOF frameworks. Using sulfonyl chlorides as reactive intermediates, Cr-MIL-SO3H and CAU-1-NH2 have been further modified to give hitherto unknown functionalized MOFs in which a sulfonamide group is bound to the framework either by its N or its S atom.

Synthesis of 2-aryl and 3-aryl benzo[b]furan thioethers using aryl sulfonyl hydrazides as sulfenylation reagents.

PubMed

Zhao, Xia; Zhang, Lipeng; Lu, Xiaoyu; Li, Tianjiao; Lu, Kui

2015-03-06

An efficient, metal-free protocol used to synthesize aryl benzo[b]furan thioethers based on the I2-catalyzed cross-coupling of benzo[b]furans as well as the electrophilic cyclization of 2-alkynylphenol derivatives with aryl sulfonyl hydrazides was developed. Various 2-aryl and 3-aryl benzo[b]furan thioethers were obtained in moderate to good yields.

Implementing Integrated Multicultural Instructional Design in Management Education

ERIC Educational Resources Information Center

Schultz, Jennifer L.; Higbee, Jeanne L.

2011-01-01

This purpose of this paper is to summarize the principles of integrated multicultural instructional design (IMID; Higbee, Goff, & Schultz, in press; Higbee, Schultz, & Goff, 2010) and present specific strategies for incorporating IMID in management education. The primary goal of IMID is to promote the integration of multicultural content…

Imide/arylene ether copolymers with pendent trifluoromethyl groups

NASA Technical Reports Server (NTRS)

Jensen, Brian J.; Havens, Stephen J.

1992-01-01

A series of imide/arylene ether block copolymers were prepared using an arylene ether block containing a hexafluoroisopropylidene group and an imide block containing a hexafluoroisopropylidene and a trifluoromethyl group in the polymer backbone. The copolymers were characterized and mechanical properties were determined and compared to the homopolymers.

The Gut Microbiota in Immune-Mediated Inflammatory Diseases

PubMed Central

Forbes, Jessica D.; Van Domselaar, Gary; Bernstein, Charles N.

2016-01-01

The collection of microbes and their genes that exist within and on the human body, collectively known as the microbiome has emerged as a principal factor in human health and disease. Humans and microbes have established a symbiotic association over time, and perturbations in this association have been linked to several immune-mediated inflammatory diseases (IMID) including inflammatory bowel disease, rheumatoid arthritis, and multiple sclerosis. IMID is a term used to describe a group of chronic, highly disabling diseases that affect different organ systems. Though a cornerstone commonality between IMID is the idiopathic nature of disease, a considerable portion of their pathobiology overlaps including epidemiological co-occurrence, genetic susceptibility loci and environmental risk factors. At present, it is clear that persons with an IMID are at an increased risk for developing comorbidities, including additional IMID. Advancements in sequencing technologies and a parallel explosion of 16S rDNA and metagenomics community profiling studies have allowed for the characterization of microbiomes throughout the human body including the gut, in a myriad of human diseases and in health. The main challenge now is to determine if alterations of gut flora are common between IMID or, if particular changes in the gut community are in fact specific to a single disease. Herein, we review and discuss the relationships between the gut microbiota and IMID. PMID:27462309

Effect of interface structure regulation caused by variation of imidization rate on conduction current characteristics of PI/nano-Al2O3 three-layer composite films

NASA Astrophysics Data System (ADS)

Ma, Xinyu; Liu, Lizhu; Zhang, Xiaorui; He, Hongju

2018-06-01

A series of sandwich structure PI films were prepared by different imidization process, with pure PI film as the interlayer and PI/Al2O3 composite films as outer layers. The imidization rate of the film with different cured processes was calculated by characterizing by infrared spectrum (FT-IR), and the morphology of interlayer interface with different imidization rates by scanning electron microscope (SEM). When the imidization conditions of the first and second films were 260 °C/120 min, the composite films displayed better interface structure and higher imidization rate (ID) than others. Moreover, results also showed that the conduction current of three-layer composite film steadily improved with increased ID and temperature, and was higher than that of the pure film. At the temperature of 30 °C, the electrical aging threshold at different ID was obtained. When the ID reached the maximum value of 78.9%, the electrical aging threshold reached the maximum 41.69 kV/mm.

Copper-catalyzed aerobic decarboxylative sulfonylation of cinnamic acids with sodium sulfinates: stereospecific synthesis of (E)-alkenyl sulfones.

PubMed

Jiang, Qing; Xu, Bin; Jia, Jing; Zhao, An; Zhao, Yu-Rou; Li, Ying-Ying; He, Na-Na; Guo, Can-Cheng

2014-08-15

A copper-catalyzed aerobic decarboxylative sulfonylation of alkenyl carboxylic acids with sodium sulfinates is developed. This study offers a new and expedient strategy for stereoselective synthesis of (E)-alkenyl sulfones that are widely present in biologically active natural products and therapeutic agents. Moreover, the transformation is proposed to proceed via a radical process and exhibits a broad substrate scope and good functional group tolerance.

Crystalline imide/arylene ether copolymers

NASA Technical Reports Server (NTRS)

Jensen, Brian J. (Inventor); Hergenrother, Paul M. (Inventor); Bass, Robert G. (Inventor)

1995-01-01

Crystalline imide/arylene ether block copolymers are prepared by reacting anhydride terminated poly(amic acids) with amine terminated poly)arylene ethers) in polar aprotic solvents and chemically or thermally cyclodehydrating the resulting intermediate poly(amic acids). The block copolymers of the invention have one glass transition temperature or two, depending on the particular structure and/or the compatibility of the block units. Most of these crystalline block copolymers for tough, solvent resistant films with high tensile properties. While all of the copolymers produced by the present invention are crystalline, testing reveals that copolymers with longer imide blocks or higher imide content have increased crystallinity.

Phosphorus-containing imide resins

NASA Technical Reports Server (NTRS)

Varma, I. K.; Fohlen, G. M.; Parker, J. A. (Inventor)

1983-01-01

Bis- and tris-imides derived from tris (m-aminophenyl) phosphine oxides by reaction with maleic anhydride or its derivatives, and addition polymers of such imides, including a variant in which a mono-imide is condensed with a dianhydride and the product is treated with a further quantity of maleic anhydride. Such monomers or their oligomes may be used to impregnate fibers and fabrics which when cured, are flame resistant. Also an improved method of producing tris (m-aminophenyl) phosphine oxides from the nitro analogues by reduction with hydrazine hydrate using palladized charcoal or Raney nickel as the catalyst is described.

Effectiveness of educational outreach in infectious diseases management: a cluster randomized trial in Uganda.

PubMed

Mbonye, Martin Kayitale; Burnett, Sarah M; Naikoba, Sarah; Ronald, Allan; Colebunders, Robert; Van Geertruyden, Jean-Pierre; Weaver, Marcia R

2016-08-04

Integrated Infectious Diseases Capacity Building Evaluation (IDCAP) teams designed and implemented two health worker in-service training approaches: 1) an off-site classroom-based integrated management of infectious diseases (IMID) course with distance learning aspects, and 2) on-site support (OSS), an educational outreach intervention. We tested the effects of OSS on workload and 12 facility performance indicators for emergency triage assessment and treatment, HIV testing, and malaria and pneumonia case management among outpatients by two subgroups: 1) mid-level practitioners (MLP) who attended IMID training (IMID-MLP) and 2) health workers who did not (No-IMID). Thirty-six health facilities participated in the IDCAP trial, with 18 randomly assigned to Arm A and 18 to Arm B. Two MLP in both arms received IMID. All providers at Arm A facilities received nine monthly OSS visits from April to December 2010 while Arm B did not. From November 2009 to December 2010, 777,667 outpatient visits occurred. We analyzed 669,580 (86.1 %) outpatient visits, where provider cadre was reported. Treatment was provided by 64 IMID-MLP and 1,515 No-IMID providers. The effect of OSS was measured by the difference in pre/post changes across arms after controlling for covariates (adjusted ratio of relative risks = a RRR). The effect of OSS on patients-per-provider-per-day (workload) among IMID-MLP (aRRR = 1.21; p = 0.48) and No-IMID (aRRR = 0.90; p = 0.44) was not statistically significant. Among IMID-MLP, OSS was effective for three indicators: malaria cases receiving an appropriate antimalarial (aRRR = 1.26, 99 % CI = 1.02-1.56), patients with negative malaria test result prescribed an antimalarial (aRRR = 0.49, 99 % CI = 0.26-0.92), and patients with acid-fast bacilli smear negative result receiving empiric treatment for acute respiratory infection (aRRR = 2.04, 99 % CI = 1.06-3.94). Among No-IMID, OSS was effective for two indicators: emergency and priority patients admitted, detained or referred (aRRR = 2.12, 99 % CI = 1.05-4.28) and emergency patients receiving at least one appropriate treatment (aRRR = 1.98, 99 % CI = 1.21-3.24). Effects of OSS on workload were not statistically significant. Significant OSS effects on facility performance across subgroups were heterogeneous. OSS supported MLP who diagnosed and treated patients to apply IMID knowledge. For other providers, OSS supported team work to manage emergency patients. This evidence on OSS effectiveness could inform interventions to improve health workers' capacity to deliver better quality infectious diseases care.

Reliable Viscosity Calculation from Equilibrium Molecular Dynamics Simulations: A Time Decomposition Method.

PubMed

Zhang, Yong; Otani, Akihito; Maginn, Edward J

2015-08-11

Equilibrium molecular dynamics is often used in conjunction with a Green-Kubo integral of the pressure tensor autocorrelation function to compute the shear viscosity of fluids. This approach is computationally expensive and is subject to a large amount of variability because the plateau region of the Green-Kubo integral is difficult to identify unambiguously. Here, we propose a time decomposition approach for computing the shear viscosity using the Green-Kubo formalism. Instead of one long trajectory, multiple independent trajectories are run and the Green-Kubo relation is applied to each trajectory. The averaged running integral as a function of time is fit to a double-exponential function with a weighting function derived from the standard deviation of the running integrals. Such a weighting function minimizes the uncertainty of the estimated shear viscosity and provides an objective means of estimating the viscosity. While the formal Green-Kubo integral requires an integration to infinite time, we suggest an integration cutoff time tcut, which can be determined by the relative values of the running integral and the corresponding standard deviation. This approach for computing the shear viscosity can be easily automated and used in computational screening studies where human judgment and intervention in the data analysis are impractical. The method has been applied to the calculation of the shear viscosity of a relatively low-viscosity liquid, ethanol, and relatively high-viscosity ionic liquid, 1-n-butyl-3-methylimidazolium bis(trifluoromethane-sulfonyl)imide ([BMIM][Tf2N]), over a range of temperatures. These test cases show that the method is robust and yields reproducible and reliable shear viscosity values.

Ion dynamics in porous carbon electrodes in supercapacitors using in situ infrared spectroelectrochemistry.

PubMed

Richey, Francis W; Dyatkin, Boris; Gogotsi, Yury; Elabd, Yossef A

2013-08-28

Electrochemical double layer capacitors (EDLCs), or supercapacitors, rely on electrosorption of ions by porous carbon electrodes and offer a higher power and a longer cyclic lifetime compared to batteries. Ionic liquid (IL) electrolytes can broaden the operating voltage window and increase the energy density of EDLCs. Herein, we present direct measurements of the ion dynamics of 1-ethyl-3-methylimidazolium bis((trifluoromethyl)sulfonyl)imide in an operating EDLC with electrodes composed of porous nanosized carbide-derived carbons (CDCs) and nonporous onion-like carbons (OLCs) with the use of in situ infrared spectroelectrochemistry. For CDC electrodes, IL ions (both cations and anions) were directly observed entering and exiting CDC nanopores during charging and discharging of the EDLC. Conversely, for OLC electrodes, IL ions were observed in close proximity to the OLC surface without any change in the bulk electrolyte concentration during charging and discharging of the EDLC. This provides experimental evidence that charge is stored on the surface of OLCs in OLC EDLCs without long-range ion transport through the bulk electrode. In addition, for CDC EDLCs with mixed electrolytes of IL and propylene carbonate (PC), the IL ions were observed entering and exiting CDC nanopores, while PC entrance into the nanopores was IL concentration dependent. This work provides direct experimental confirmation of EDLC charging mechanisms that previously were restricted to computational simulations and theories. The experimental measurements presented here also provide deep insights into the molecular level transport of IL ions in EDLC electrodes that will impact the design of the electrode materials' structure for electrical energy storage.

Determination of the thermal stability of fluids by tensimetry - Instrumentation and procedure

NASA Technical Reports Server (NTRS)

Helmick, Larry S.; Jones, William R., Jr.

1990-01-01

A computerized tensimeter and experimental procedure for determination of the thermal decomposition temperature (T sub d) of perfluoro alkylethers were developed and tested. Both the apparatus and the procedure are described in detail. Results of testing with bis(2-ethylhexyl) phthalate and trimethylolpropane triheptanoate demonstrate that the reciprocal of the decomposition temperature is a linear function of the logarithm of the gas volume/heated liquid volume ratio. The T sub d obtained for each compound at a gas volume/heated liquid volume ration of one was similar to the value previously reported using an isoteniscope technique. Results of testing with a polymer of hexafluoropropylene oxide demonstrate that this instrument and procedure can be used to determine the T sub d of perfluoro alkylethers.

Solute-solvent contact by intermolecular cross relaxation. I. The nature of the water-hydrophobic interface.

PubMed

Nordstierna, Lars; Yushmanov, Pavel V; Furó, István

2006-08-21

Intermolecular cross-relaxation rates between solute and solvent were measured by {1H} 19F nuclear magnetic resonance experiments in aqueous molecular solutions of ammonium perfluoro-octanoate and sodium trifluoroacetate. The experiments performed at three different magnetic fields provide frequency-dependent cross-relaxation rates which demonstrate clearly the lack of extreme narrowing for nuclear spin relaxation by diffusionally modulated intermolecular interactions. Supplemented by suitable intramolecular cross-relaxation, longitudinal relaxation, and self-diffusion data, the obtained cross-relaxation rates are evaluated within the framework of recent relaxation models and provide information about the hydrophobic hydration. In particular, water dynamics around the trifluoromethyl group in ammonium perfluoro-octanoate are more retarded than that in the smaller trifluoroacetate.

Solvent free low-melt viscosity imide oligomers and thermosetting polymide composites

NASA Technical Reports Server (NTRS)

Chuang, Chun-Hua (Inventor)

2012-01-01

.[.This invention relates to the composition and a solvent-free process for preparing novel imide oligomers and polymers specifically formulated with effective amounts of a dianhydride such as 2,3,3',4-biphenyltetra carboxylic dianydride (a-BPDA), at least one aromatic diamine and an endcapped of 4-phenylethynylphthalic anhydride (PEPA) or nadic anhydride to produce imide oligomers that possess a low-melt viscosity of 1-60 poise at 260-280.degree. C. When the imide oligomer melt is cured at about 371.degree. C. in a press or autoclave under 100-500 psi, the melt resulted in a thermoset polyimide having a glass transition temperature (T.sub.g) equal to and above 310.degree. C. A novel feature of this process is that the monomers; namely the dianhydrides, diamines and the endcaps, are melt processable to form imide oligomers at temperatures ranging between 232-280.degree. C. (450-535.degree. F.) without any solvent. These low-melt imide oligomers can be easily processed by resin transfer molding (RTM), vacuum-assisted resin transfer molding (VARTM) or the resin infusion process with fiber preforms e.g. carbon, glass or quartz preforms to produce polyimide matrix composites with 288-343.degree. C. (550-650.degree. F.) high temperature performance capability..]. .Iadd.This invention relates to compositions and a solvent-free reaction process for preparing imide oligomers and polymers specifically derived from effective amounts of dianhydrides such as 2,3,3',4'-biphenyltetracarboxylic dianhydride (a-BPDA), at least one aromatic polyamine and an end-cap such as 4-phenylethynyphthalic anhydride (PEPA) or nadic anhydride to produce imide oligomers that possess a low-melt viscosity of 1-60 poise at 260.degree. C.-280.degree. C..Iaddend.

Kinetics of imidization and crosslinking in PMR-polyimide resin

NASA Technical Reports Server (NTRS)

Lauver, R. W.

1977-01-01

Infrared spectroscopy and differential scanning calorimetry were employed to study the imidization and crosslinking kinetics of norbornenyl-capped, addition-type polyimide resins (designated PMR for polymerization of monomer reactants). The spectral and thermal analyses were performed on resin specimens which had been isothermally aged at temperatures appropriate for imidization (120 to 204 C) and crosslinking (275 to 325 C). Imidization occurs rapidly (approximately 0.01/min) at short times, while at times longer than approximately 0.5 hour, the rate decreases significantly (approximately 0.0001/min). The crosslinking reaction exhibits first order kinetics during the initial portion of the reaction and its rate appears to be limited by the reversion of the norbornenyl Diels-Alder adduct. The total heat evolved per mole of endcap during crosslinking shows an inverse dependence on the molecular weight of the imide prepolymers. This reflects the effect of endcap dilution and decreased mobility of the larger oligomers.

Solvent Free Low-Melt Viscosity Imide Oligomers And Thermosetting Polyimide Composites

NASA Technical Reports Server (NTRS)

Chuang, CHun-Hua (Inventor)

2006-01-01

This invention relates to the composition and a solvent-free process for preparing novel imide oligomers and polymers specifically formulated with effective amounts of a dianhydride such as 2,3,3',4-biphenyltetra carboxylic dianydride (a-BPDA), at least one aromatic diamine' and an endcapped of 4-phenylethynylphthalic anhydride (PEPA) or nadic anhydride to produce imide oligomers that possess a low-melt viscosity of 1-60 poise at 260-280" C. When the imide oligomer melt is cured at about 371 C. in a press or autoclave under 100-500 psi, the melt resulted in a thermoset polyimide having a glass transition temperature (T(sub g)) equal to and above 310 C. A novel feature of this process is that the monomers; namely the dianhydrides, diamines and the endcaps, are melt processable to form imide oligomers at temperatures ranging between 232-280 C. (450-535 F) without any solvent. These low-melt imide oligomers can be easily processed by resin transfer molding (RTM), vacuum-assisted resin transfer molding (VARTM) or the resin infusion process with fiber preforms e.g. carbon, glass or quartz preforms to produce polyimide matrix composites with 288-343C (550-650 F) high temperature performance capability.

Perfluoro anion based binary and ternary ionic liquids as electrolytes for dye-sensitized solar cells

NASA Astrophysics Data System (ADS)

Lin, Hsi-Hsin; Peng, Jia-De; Suryanarayanan, V.; Velayutham, D.; Ho, Kuo-Chuan

2016-04-01

In this work, eight new ionic liquids (ILs) based on triethylammonium (TEA) or n-methylpiperidinium (NMP) cations and perfluoro carboxylate (PFC) anions having different carbon chain lengths are synthesized and their physico-chemical properties such as density, decomposition temperature, viscosity and conductivity are determined. Photovoltaic characteristics of dye-sensitized solar cells (DSSCs) with binary ionic liquids electrolytes, containing the mixture of the synthesized ILs and 1-methyl-3-propyl imidazolium iodide (PMII) (v/v = 35/65), are evaluated. Among the different ILs, solar cells containing NMP based ILs show higher VOC than that of TEA, whereas, higher JSC is noted for the DSSCs incorporated with the latter when compared to the former. Further, the photo-current of the DSSCs decreases with the increase of the carbon chain length of perfluoro carboxylate anionic group of ILs. The cell performance of the DSSC containing ternary ionic liquids-based electrolytes compose of NMP-2C/TEA-2C/PMII (v/v/v = 28/7/65) exhibits a JSC of 12.99 mA cm-2, a VOC of 639.0 mV, a FF of 0.72, and a cell efficiency of 6.01%. The extraordinary durability of the DSSC containing the above combination of electrolytes stored in dark at 50 °C is proved to be unfailing up to 1200 h.

Antiandrogenic steroidal sulfonyl heterocycles. Utility of electrostatic complementarity in defining bioisosteric sulfonyl heterocycles.

PubMed

Mallamo, J P; Pilling, G M; Wetzel, J R; Kowalczyk, P J; Bell, M R; Kullnig, R K; Batzold, F H; Juniewicz, P E; Winneker, R C; Luss, H R

1992-05-15

Complementarity of electrostatic potential surface maps was utilized in defining bioisosteric steroidal androgen receptor antagonists. Semiempirical and ab initio level calculations performed on a series of methanesulfonyl heterocycles indicated the requirement for a partial negative charge at the heteroatom attached to C-3 of the steroid nucleus to attain androgen receptor affinity. Synthesis and testing of six heterocycle A-ring-fused dihydroethisterone derivatives support this hypothesis, and we have identified two new androgen receptor antagonists of this class.

Tetrabutylammonium Iodide-Promoted Thiolation of Oxindoles Using Sulfonyl Chlorides as Sulfenylation Reagents.

PubMed

Zhao, Xia; Wei, Aoqi; Lu, Xiaoyu; Lu, Kui

2017-08-01

3-Sulfanyloxindoles were synthesised by triphenylphosphine-mediated transition-metal-free thiolation of oxindoles using sulfonyl chlorides as sulfenylation reagents. The above reaction was promoted by iodide anions, which was ascribed to the in situ conversion of sulfenyl chlorides into the more reactive sulfenyl iodides. Moreover, the thiolation of 3-aryloxindoles was facilitated by bases. The use of a transition-metal-free protocol, readily available reagents, and mild reaction conditions make this protocol more practical for preparing 3-sulfanyloxindoles than traditional methods.

Rodent repellents: Preparation and properties of thiouronium compounds and cyclic imides

USGS Publications Warehouse

Bellack, E.; DeWitt, J.B.

1954-01-01

Syntheses and bioassays of cyclic imides and thiouronium compounds were carried out as part of a search for materials capable of preventing rodent damage to packaged commodities. Previous studies had shown that repellent activity was associated with functional groups containing nitrogen and sulfur, and was enhanced by the presence of ionic linkages. Twenty-seven thiouronium compounds and 40 imides, including 1 0 compounds not described previously, were prepared for these tests. Ten imides and 26 thiouronium compounds were repellent under the conditions of test. Information obtained in these studies will be utilized in the development and selection of more effective materials for prevention of rodent damage to foods and other commodities.

Studies of new perfluoroether elastomeric sealants. [for aircraft fuel tanks

NASA Technical Reports Server (NTRS)

Basiulis, D. I.; Salisbury, D. P.

1981-01-01

Channel and filleting sealants were developed successfully from cyano and diamidoxime terminated perfluoro alkylene ether prepolymers. The prepolymers were polymerized, formulated and tested. The polymers and/or formulations therefrom were evaluated as to their physical, mechanical and chemical properties (i.e., specific gravity, hardness, nonvolatile content, corrosion resistance, stress corrosion, pressure rupture resistance, low temperature flexibility, gap sealing efficiency, tensile strength and elongation, dynamic mechanical behavior, compression set, fuel resistance, thermal properties and processability). Other applications of the formulated polymrs and incorporation of the basic prepolymers into other polymeric systems were investigated. A cyano terminated perfluoro alkylene oxide triazine was formulated and partially evaluated. The channel sealant in its present formulation has excellent pressure rupture resistance and surpasses present MIL specifications before and after fuel and heat aging.

Syntheses and Degradations of Fluorinated Heterocyclics. 2; Perfluoroalkyl and Perfluroalkylether-1,2,4-Oxadiazoles

NASA Technical Reports Server (NTRS)

Paciorek, K. J. L.; Kratzer, R. H.; Kaufman, J.; Nakahara, J. H.; Rosser, R. W.; Parker, J. A.

1977-01-01

3-Perfluoroalkylether-5-perfluoro-n-heptyl-1,2,4-oxadiazole and 3,S-bis(perfluoroalkylether)-1,2,4-oxadiazole were synthesized and characterized. The 3, 5-bis(perfluoroalkylether)-l, 2,4-oxadiazole was subjected to thermal, thermal oxidative, and hydrolytic degradations at 235 and 325 C and was found to be stable under these conditions as evidenced by practically quantitative recovery of the test samples. In the presence of Jet-A fuel at 235 C a low degree of degradation, approximately 4%, was observed. 3,5-Bis(perfluoro-n-heptyl)-1,2,4-oxadiazole was found to be stable to attack by water at 325 C; however in air in the presence of jet-A at 235 C the extent of degradation was in excess of 10%.

Identification of an organic semiconductor superlattice structure of pentacene and perfluoro-pentacene through resonant and non-resonant X-ray scattering

DOE PAGES

Kowarik, S.; Hinderhofer, A.; Wang, C.; ...

2015-11-30

Highly crystalline and stable molecular superlattices are grown with the smallest possible stacking period using monolayers (MLs) of the organic semiconductors pentacene (PEN) and perfluoro-pentacene (PFP). Superlattice reflections in X-ray reflectivity and their energy dependence in resonant soft X-ray reflectivity measurements show that PFP and PEN MLs indeed alternate even though the coherent ordering is lost after ~ 4 ML. The observed lattice spacing of 15.9 Å in the superlattice is larger than in pure PEN and PFP films, presumably because of more upright standing molecules and lack of interdigitation between the incommensurate crystalline PEN and PFP layers. The findingsmore » are important for the development of novel organic quantum optoelectronic devices.« less

Methyl sulfonyl polychlorinated biphenyls and 2,2-bis(4-chlorophenyl)-1,1-dichlorethene in gray seal tissues determined by gas chromatography with electron capture detection and atomic emission detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Janak, K.; Becker, G.; Colmisjoe, A.

1998-06-01

The presence of 24 methyl sulfonyl polychlorinated biphenyl (PCB) congeners (MeSO{sub 2}-CBs) and 3-methyl sulfonyl 2,2-bis(4-chlorophenyl)-1,1-dichlorethene (DDE) (MeSO{sub 2}-DDE), metabolites of PCB and DDE, in blubber, lung, and liver of gray seals has been determined by using atomic emission detection (AED) and electron capture detection (ECD). Selective accumulation of aryl methyl sulfones in blubber, liver, and lung tissue was also investigated. For the liver samples, a substantial and highly specific retention of PCB methyl sulfones was observed. The atomic emission technique significantly improved the determination of measured solutes compared with ECD. Atomic emission detection was also valuable for the monitoringmore » of the prefractionation and to decrease the requirements of sample clean-up. Comparing both detection techniques showed a good correlation between the results of the AED sulfur-selective line and ECD.« less

Comparative study of imide-based Li salts as electrolyte additives for Li-ion batteries

NASA Astrophysics Data System (ADS)

Sharova, Varvara; Moretti, Arianna; Diemant, Thomas; Varzi, Alberto; Behm, R. Jürgen; Passerini, Stefano

2018-01-01

Herein, we report the results of a detailed study on the use of different Li imide salts (LiTFSI, LiFSI, and LiFTFSI) as electrolyte additives for lithium-ion batteries. The introduction of lithium imide salts in the electrolyte is shown to considerably improve the first cycle coulombic efficiency and the long-term cycling stability of graphite/LiFePO4 cells. Using LiTFSI, a capacity fading of only ∼2% occurred over 600 cycles while the control cell with the state-of-the-art additive (VC) lost ∼20% of the initial capacity at 20 °C. The results of the XPS and impedance spectroscopy measurements of graphite electrodes show that, after the formation cycle, the SEI obtained in the presence of imide salts is thinner, contains more LiF and is less resistive than that obtained using VC. Despite the beneficial effect of the imide salts on the lithium-ion cell performance, a slightly reduced thermal stability of the SEI is observed.

Kaolinite Nanocomposite Platelets Synthesized by Intercalation and Imidization of Poly(styrene-co-maleic anhydride)

PubMed Central

Samyn, Pieter; Schoukens, Gustaaf; Stanssens, Dirk

2015-01-01

A synthesis route is presented for the subsequent intercalation, exfoliation and surface modification of kaolinite (Kln) by an imidization reaction of high-molecular weight poly(styrene-co-maleic anhydride) or SMA in the presence of ammonium hydroxide. In a first step, the intercalation of ammonolyzed SMA by guest displacement of intercalated dimethylsulfoxide has been proven. In a second step, the imidization of ammonolyzed SMA at 160 °C results in exfoliation of the kaolinite layers and deposition of poly(styrene-co-maleimide) or SMI nanoparticles onto the kaolinite surfaces. Compared with a physical mixture of Kln/SMI, the chemically reacted Kln/SMI provides more efficient exfoliation and hydrogen bonding between the nanoparticles and the kaolinite. The kaolinite nanocomposite particles are synthesized in aqueous dispersion with solid content of 65 wt %. The intercalation and exfoliation are optimized for a concentration ratio of Kln/SMI = 70:30, resulting in maximum intercalation and interlayer distance in combination with highest imide content. After thermal curing at 135 °C, the imidization proceeds towards a maximum conversion of the intermediate amic acid moieties. The changes in O–H stretching and kaolinite lattice vibrations have been illustrated by infrared and FT-Raman spectroscopy, which allow for a good quantification of concentration and imidization effects. PMID:28793445

Correlating the synthesis protocol of aromatic polyimide film with the properties of polyamic acid precursor

NASA Astrophysics Data System (ADS)

Tan, P. C.; Ooi, B. S.; Ahmad, A. L.; Low, S. C.

2017-06-01

Thousands of different copolyimide combinations render it technically impossible to have a single universal synthesis method to produce aromatic polyimide film. This study aimed to outline the selection of synthesis protocol, either through the casting of chemically imidized polyimide solution or thermal imidization of polyamic acid (PAA), to produce the polyimide film. The rheological behaviour, molecular weight, and solubility of five structurally different PAA were analysed and correlated to both imidization methods. In this work, a tough polyimide film was successfully synthesized by casting the chemically imidized polyimide derived from high viscosity (> 81 cP) and high molecular weight (≥ 1.35 x 106 g/mol) PAA. On the contrary, both low viscosity (< 13 cP) and high viscosity (> 81 cP) PAA demonstrated the possibility to produce polyimide film via thermal imidization route. The longer molecular chain of ODPA-6FpDA:DABA (3:2) polyimide produced from thermal imidization had restricted the passage of CO2 across the polyimide film when it was applied in the gas separation application. The outcome from this work serves as a guideline for the selection of suitable polyimide film synthesis protocol, which will minimize the time and chemical consumption in future exploration of new polyimide structure.

Molecular mechanism of action of immune-modulatory drugs thalidomide, lenalidomide and pomalidomide in multiple myeloma

PubMed Central

Zhu, Yuan Xiao; Kortuem, K. Martin; Stewart, A. Keith

2014-01-01

Although several mechanisms have been proposed to explain the activity of thalidomide, lenalidomide and pomalidomide in multiple myeloma (MM), including demonstrable anti-angiogenic, anti-proliferative and immunomodulatory effects, the precise cellular targets and molecular mechanisms have only recently become clear. A landmark study recently identified cereblon (CRBN) as a primary target of thalidomide teratogenicity. Subsequently it was demonstrated that CRBN is also required for the anti-myeloma activity of thalidomide and related drugs, the so-called immune-modulatory drugs (IMiDs). Low CRBN expression was found to correlate with drug resistance in MM cell lines and primary MM cells. One of the downstream targets of CRBN identified is interferon regulatory factor 4 (IRF4), which is critical for myeloma cell survival and is down-regulated by IMiD treatment. CRBN is also implicated in several effects of IMiDs, such as down-regulation of tumor necrosis factor-α (TNF-α) and T cell immunomodulatory activity, demonstrating that the pleotropic actions of the IMiDs are initiated by binding to CRBN. Future dissection of CRBN downstream signaling will help to delineate the underlying mechanisms for IMiD action and eventually lead to development of new drugs with more specific anti-myeloma activities. It may also provide a biomarker to predict IMiD response and resistance. PMID:22966948

Novel poly(imide dioxime) sorbents: Development and testing for enhanced extraction of uranium from natural seawater

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, Sadananda; Brown, Suree; Mayes, Richard T.

2016-04-09

We synthesized a new series of amidoxime-based polymer adsorbents at the Oak Ridge National Laboratory (ORNL) by electron beam induced grafting of acrylonitrile and itaconic acid onto polyethylene fiber. We also demonstrate hydroxylamine derivatives of poly(acrylonitrile) (PAN) moiety to possess two kinds of functional groups: open-chain amidoxime and cyclic imide dioxime. The open-chain amidoxime is shown to convert to imide dioxime on heat treatment in the presence of an aprotic solvent, like dimethylsulfoxide (DMSO). Furthermore, the formation of amidoxime and imide dioxime was confirmed by 13C CP-MAS spectra. The adsorbents were evaluated for uranium adsorption efficiency at ORNL with simulatedmore » seawater spiked with 8 ppm uranium and 5 gallon seawater in a batch reactor, and in flow-through columns with natural seawater at the Marine Science Laboratory (MSL) of Pacific Northwest National Laboratory (PNNL) at Sequim Bay, WA. The DMSO-heat-treated sorbents adsorbed uranium as high as 4.48 g-U/kg-ads. from seawater. Experimental evidence is presented that the poly(imide dioxime) is primarily responsible for enhanced uranium adsorption capacity from natural seawater. The conjugated system in the imide dioxime ligand possesses increased electron donation ability, which is believed to significantly enhance the uranyl coordination in seawater.« less

Multidisciplinary Management of Spondyloarthritis-Related Immune-Mediated Inflammatory Disease.

PubMed

Rizzello, Fernando; Olivieri, Ignazio; Armuzzi, Alessandro; Ayala, Fabio; Bettoli, Vincenzo; Bianchi, Luca; Cimino, Luca; Costanzo, Antonio; Cristaudo, Antonio; D'Angelo, Salvatore; Daperno, Marco; Fostini, Anna Chiara; Galeazzi, Mauro; Gilio, Michele; Gionchetti, Paolo; Gisondi, Paolo; Lubrano, Ennio; Marchesoni, Antonio; Offidani, Annamaria; Orlando, Ambrogio; Pugliese, Daniela; Salvarani, Carlo; Scarpa, Raffaele; Vecchi, Maurizio; Girolomoni, Giampiero

2018-04-01

Immune-mediated inflammatory diseases (IMIDs) are chronic autoimmune conditions that share common pathophysiologic mechanisms. The optimal management of patients with IMIDs remains challenging because the coexistence of different conditions requires the intervention of several specialists. The aim of this study was to develop a series of statements defining overarching principles that guide the implementation of a multidisciplinary approach for the management of spondyloarthritis (SpA)-related IMIDs including SpA, psoriasis, psoriatic arthritis, Crohn's disease, ulcerative colitis and uveitis. A Delphi consensus-based approach was used to identify a core set of statements. The process included development of initial questions by a steering committee, an exhaustive search of the literature using complementary approaches to identify potential statements and two Delphi voting rounds for finalization of the statements. Consensus was achieved on the related nature of IMIDs, the existence of a high prevalence of multiple IMIDs in a single patient and the fact that a multidisciplinary approach can result in a more extensive evaluation and comprehensive approach to treatment. The goals of a multidisciplinary team should be to increase diagnosis of concomitant IMIDs, improve the decision-making process, and increase patient satisfaction and adherence. Early referral and diagnosis, early recognition of concomitant IMIDs and optimizing treatment to improve patient quality of life are some of the advantages of using multidisciplinary teams. To be effective, a multidisciplinary team should be equipped with the appropriate tools for diagnosis and follow-up, and at a minimum the multidisciplinary team should include a dermatologist, gastroenterologist and rheumatologist; providing psychologic support via a psychologist and involving an ophthalmologist, general practitioners and nurses in multidisciplinary care is also important. The present Delphi consensus identified a set of overarching principles that may be useful for implementation of a multidisciplinary approach for the management of SpA-related IMIDs. Aristea and Hippocrates.

Rhodium-Catalyzed Regioselective Synthesis of Isocoumarins through Benzothiadiazine-Fused Frameworks.

PubMed

Dalvi, Prashant B; Lin, Kuang-Ling; Kulkarni, Manohar V; Sun, Chung-Ming

2016-08-05

An unprecedented two-step, one-pot synthesis of benzimidazothiadiazine 5,5-dioxides is presented. Reaction condition based regioselectivity has been achieved where fused benzimidazo[1,2-b][1,2,4]thiadiazines are exclusively formed under thermal conditions, whereas benzimidazo[2,1-c][1,2,4]thiadiazines were created only under microwave irradiation. The salient features of this protocol include a regioselective sulfonylation of 2-aminobenzimidazole with o-halo sulfonyl chlorides followed by N-C bond formation. The acid forms of these fused regioisomers have been used to introduce novel guanidine-containing isocoumarin frameworks.

Enantioselective copper catalysed intramolecular C-H insertion reactions of α-diazo-β-keto sulfones, α-diazo-β-keto phosphine oxides and 2-diazo-1,3-diketones; the influence of the carbene substituent.

PubMed

Shiely, Amy E; Slattery, Catherine N; Ford, Alan; Eccles, Kevin S; Lawrence, Simon E; Maguire, Anita R

2017-03-22

Enantioselectivities in C-H insertion reactions, employing the copper-bis(oxazoline)-NaBARF catalyst system, leading to cyclopentanones are highest with sulfonyl substituents on the carbene carbon, and furthermore, the impact is enhanced by increased steric demand on the sulfonyl substituent (up to 91%ee). Enantioselective intramolecular C-H insertion reactions of α-diazo-β-keto phosphine oxides and 2-diazo-1,3-diketones are reported for the first time.

Rust-Inhibited Nonreactive Perfluorinated Polymer Greases

DTIC Science & Technology

Perfluoroalkylpolyether fluids thickened with polytetrafluoroethylene were studied in connection with the development of rust-inhibited chemically...dimethyloctadecylbenzyl ammonium bentonite + sodium nitrate imparts very effective rust-preventive properties to perfluoro polymer grease mixtures. Data are

Immunomodulatory drugs disrupt the cereblon-CD147-MCT1 axis to exert antitumor activity and teratogenicity.

PubMed

Eichner, Ruth; Heider, Michael; Fernández-Sáiz, Vanesa; van Bebber, Frauke; Garz, Anne-Kathrin; Lemeer, Simone; Rudelius, Martina; Targosz, Bianca-Sabrina; Jacobs, Laura; Knorn, Anna-Maria; Slawska, Jolanta; Platzbecker, Uwe; Germing, Ulrich; Langer, Christian; Knop, Stefan; Einsele, Herrmann; Peschel, Christian; Haass, Christian; Keller, Ulrich; Schmid, Bettina; Götze, Katharina S; Kuster, Bernhard; Bassermann, Florian

2016-07-01

Immunomodulatory drugs (IMiDs), such as thalidomide and its derivatives lenalidomide and pomalidomide, are key treatment modalities for hematologic malignancies, particularly multiple myeloma (MM) and del(5q) myelodysplastic syndrome (MDS). Cereblon (CRBN), a substrate receptor of the CRL4 ubiquitin ligase complex, is the primary target by which IMiDs mediate anticancer and teratogenic effects. Here we identify a ubiquitin-independent physiological chaperone-like function of CRBN that promotes maturation of the basigin (BSG; also known as CD147) and solute carrier family 16 member 1 (SLC16A1; also known as MCT1) proteins. This process allows for the formation and activation of the CD147-MCT1 transmembrane complex, which promotes various biological functions, including angiogenesis, proliferation, invasion and lactate export. We found that IMiDs outcompete CRBN for binding to CD147 and MCT1, leading to destabilization of the CD147-MCT1 complex. Accordingly, IMiD-sensitive MM cells lose CD147 and MCT1 expression after being exposed to IMiDs, whereas IMiD-resistant cells retain their expression. Furthermore, del(5q) MDS cells have elevated CD147 expression, which is attenuated after IMiD treatment. Finally, we show that BSG (CD147) knockdown phenocopies the teratogenic effects of thalidomide exposure in zebrafish. These findings provide a common mechanistic framework to explain both the teratogenic and pleiotropic antitumor effects of IMiDs.

Immunomodulatory drugs and the risk of serious infection in multiple myeloma: systematic review and meta-analysis of randomized and observational studies.

PubMed

Chen, Min; Zhao, Yongfeng; Xu, Chuanxin; Wang, Xian; Zhang, Xianping; Mao, Benyu

2018-06-01

The effect of immunomodulatory drugs (IMiDs) on serious infection remains uncertain. We therefore conducted a systematic review and meta-analysis to assess the possible impact of IMiDs on serious infection in patients with multiple myeloma (MM). We searched randomized controlled trials (RCTs) and observational studies from databases that addressed the effect of IMiDs on serious infection in patients with MM. We pooled data from RCTs and observational studies separately and used the GRADE approach to rate the quality of evidence. Rates in patients with individual IMiDs at different treatment status ranged from 7.00 to 23.00%. The use of thalidomide- or lenalidomide-based regimen induction therapy for autologous stem cell transplantation (ASCT)-ineligible patients suggests increase in serious infection (RR = 1.59, 95% CI 1.31-1.93, p < 0.01). Compared to conventional therapy, IMiDs' induction in ASCT-eligible patients significantly decreases the risk of serious infection (RR = 0.82, 95% CI 0.72-0.94, p < 0.01). Lenalidomide-based therapy was associated with a significant increase in risk of serious infection in patients treated compared with conventional therapy (RR = 2.45, 95% CI 1.57-3.83, p < 0.01). The current evidence suggests that patients with MM treated with IMiDs are at a high risk of serious infection.

CF3+ fragmentation by electron impact ionization of perfluoro-propyl-vinyl-ethers, C5F10O, in gas phase

NASA Astrophysics Data System (ADS)

Kondo, Yusuke; Ishikawa, Kenji; Hayashi, Toshio; Miyawaki, Yudai; Takeda, Keigo; Kondo, Hiroki; Sekine, Makoto; Hori, Masaru

2015-04-01

The gas phase fragmentations of perfluoro-propyl-vinyl ether (PPVE, C5F10O) are studied experimentally. Dominant fragmentations of PPVE are found to be the result of a dissociative ionization reaction, i.e., CF3+ via direct bond cleavage, and C2F3O- and C3F7O- via electron attachment. Regardless of the appearance energy of around 14.5 eV for the dissociative ionization of CF3+, the observed ion efficiency for the CF3+ ion was extremely large the order of 10-20 cm-2, compared with only 10-21 cm-2 for the other channels. PPVE characteristically generated CF3+ as the largest abundant ion are advantageous for use of feedstock gases in plasma etching processes.

Parahydrogen-induced polarization transfer to 19F in perfluorocarbons for 19F NMR spectroscopy and MRI.

PubMed

Plaumann, Markus; Bommerich, Ute; Trantzschel, Thomas; Lego, Denise; Dillenberger, Sonja; Sauer, Grit; Bargon, Joachim; Buntkowsky, Gerd; Bernarding, Johannes

2013-05-10

Fluorinated substances are important in chemistry, industry, and the life sciences. In a new approach, parahydrogen-induced polarization (PHIP) is applied to enhance (19)F MR signals of (perfluoro-n-hexyl)ethene and (perfluoro-n-hexyl)ethane. Unexpectedly, the end-standing CF3 group exhibits the highest amount of polarization despite the negligible coupling to the added protons. To clarify this non-intuitive distribution of polarization, signal enhancements in deuterated chloroform and acetone were compared and (19)F-(19)F NOESY spectra, as well as (19)F T1 values were measured by NMR spectroscopy. By using the well separated and enhanced signal of the CF3 group, first (19)F MR images of hyperpolarized linear semifluorinated alkenes were recorded. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Branched-chain dicationic ionic liquids for fatty acid methyl ester assessment by gas chromatography.

PubMed

Talebi, Mohsen; Patil, Rahul A; Sidisky, Leonard M; Berthod, Alain; Armstrong, Daniel W

2017-12-06

Twelve bis- or dicationic ionic liquids (ILs) including eight based on imidazolium, a single one based on phosphonium, and three based on pyrrolidinium cationic units were prepared with the bis(trifluoromethyl sulfonyl) imide anion. The two identical cationic moieties were attached by different alkyl spacers having three or five carbons and differing alkyl substituents attached to the spacer. The SLB-IL111 column, as the most polar commercial stationary phase known, was included in the study for comparison. Isothermal separations of a rapeseed oil fatty acid methyl ester (FAME) sample were used to study and compare the 12 IL-based column performances and selectivities. The retention times of the most retained methyl esters of lignoceric (C24:0) and erucic (C22:1) acids were used to estimate the IL polarity. The phosphonium dicationic IL column was, by far, the least polar. Imidazolium-based dicationic IL columns were the most polar. Polarity and selectivity for the FAME separation were somewhat related. The separation of a 37-FAME standard mixture allowed the investigation of selectivity variations observed on the 12 IL-based columns under temperature gradients up to 230 °C. The remarkable selectivity of the IL-based columns is demonstrated by the detailed analysis of the cis/trans C18:1 isomers of a partially hydrogenated vegetable oil sample on 30-m columns, separations competing with that done following an "official method" performed on a 100-m column. Graphical abstract Separation of fatty acid methyl esters on a 30-m 3m 2 C 5 (mpy) 2 . 2NTf 2 branched-chain dicationic IL-based column. Branched chain dicationic ILs show great selectivity for separation of cis/trans, ω-3/ω-6, and detailed analysis of cis/trans fats.

Magnetic ionic liquids as non-conventional extraction solvents for the determination of polycyclic aromatic hydrocarbons.

PubMed

Trujillo-Rodríguez, María J; Nacham, Omprakash; Clark, Kevin D; Pino, Verónica; Anderson, Jared L; Ayala, Juan H; Afonso, Ana M

2016-08-31

This work describes the applicability of magnetic ionic liquids (MILs) in the analytical determination of a group of heavy polycyclic aromatic hydrocarbons. Three different MILs, namely, benzyltrioctylammonium bromotrichloroferrate (III) (MIL A), methoxybenzyltrioctylammonium bromotrichloroferrate (III) (MIL B), and 1,12-di(3-benzylbenzimidazolium) dodecane bis[(trifluoromethyl)sulfonyl)]imide bromotrichloroferrate (III) (MIL C), were designed to exhibit hydrophobic properties, and their performance examined in a microextraction method for hydrophobic analytes. The magnet-assisted approach with these MILs was performed in combination with high performance liquid chromatography and fluorescence detection. The study of the extraction performance showed that MIL A was the most suitable solvent for the extraction of polycyclic aromatic hydrocarbons and under optimum conditions the fast extraction step required ∼20 μL of MIL A for 10 mL of aqueous sample, 24 mmol L(-1) NaOH, high ionic strength content of NaCl (25% (w/v)), 500 μL of acetone as dispersive solvent, and 5 min of vortex. The desorption step required the aid of an external magnetic field with a strong NdFeB magnet (the separation requires few seconds), two back-extraction steps for polycyclic aromatic hydrocarbons retained in the MIL droplet with n-hexane, evaporation and reconstitution with acetonitrile. The overall method presented limits of detection down to 5 ng L(-1), relative recoveries ranging from 91.5 to 119%, and inter-day reproducibility values (expressed as relative standard derivation) lower than 16.4% for a spiked level of 0.4 μg L(-1) (n = 9). The method was also applied for the analysis of real samples, including tap water, wastewater, and tea infusion. Copyright © 2016 Elsevier B.V. All rights reserved.

Polypyrrol/chitosan hydrogel hybrid microfiber as sensing artificial muscle

NASA Astrophysics Data System (ADS)

Ismail, Yahya A.; Martínez, Jose G.; Al Harrasi, Ahmad S.; Kim, Seon J.; Fernández Otero, Toribio F.

2011-04-01

An electrochemical actuator demands that it should act as a sensor of the working conditions for its efficient application in devices. Actuation and sensing characteristics of a biopolymer/conducting polymer hybrid microfiber artificial muscle fabricated through wet spinning of a chitosan solution followed by in situ chemical polymerization with pyrrol employing bis(triflouro methane sulfonyl) imide as dopant and ferric chloride as a catalyst is presented. The polypyrrol/chitosan hybrid microfiber was investigated by FTIR, scanning electron microscopy (SEM), electrical conductivity measurement, cyclic voltammetric and chronopotentiometric methods. The electrochemical measurements related to the sensing abilities were performed as a function of applied current, concentration and temperature keeping two of the variables constant at a given time using NaCl as electrolyte. Cyclic voltammograms confirmed that the electro activity is imparted by polypyrrol (pPy). The fiber showed an electrical conductivity of 3.21x10-1 Scm-1and an average linear electrochemical actuation strain of 0.54%. The chronopotentiometric responses during the oxidation/reduction processes of the microfiber for the different anodic/cathodic currents and the linear fit observed for the consumed electrical energy during the reaction for various applied currents suggested that it can act as a sensor of applied current. The chronopotentiometric responses and the linear fit of consumed electrical energy at different temperatures suggested that the actuator can act as a temperature sensor. Similarly a semi logarithmic dependence of the consumed electrical energy with concentration of the electrolyte during reaction is suggestive of its applicability as a concentration sensor. The demand that an electrochemical actuator to be a sensor of the working conditions, for its efficient application in devices is thus verified in this material.

Preparation of stir cake sorptive extraction based on polymeric ionic liquid for the enrichment of benzimidazole anthelmintics in water, honey and milk samples.

PubMed

Wang, Yulei; Zhang, Jie; Huang, Xiaojia; Yuan, Dongxing

2014-08-20

In this work, a new stir cake sorptive extraction (SCSE) using polymeric ionic liquid monolith as sorbent was prepared. The sorbent was obtained by in situ copolymerization of an ionic liquid, 1-allyl-3-methylimidazolium bis[(trifluoro methyl)sulfonyl]imide (AMII) and divinylbenzene (DB) in the presence of N,N-dimethylformamide. The influence of the content of ionic liquid and the porogen in the polymerization mixture on extraction performance was studied thoroughly. The physicochemical properties of the polymeric ionic liquid were characterized by infrared spectroscopy, elemental analysis, scanning electron microscopy and mercury intrusion porosimetry. The usefulness of SCSE-AMIIDB was demonstrated by the enrichment of trace benzimidazole anthelmintics. Several parameters affecting the extraction efficiency were investigated, and under the optimized conditions, a simple and effective method for the determination of trace benzimidazoles residues in water, milk and honey samples was established by coupling SCSE-AMIIDB with high performance liquid chromatography/diode array detection (SCSE-AMIIDB-HPLC/DAD). Results indicated that the limits of detection (S/N=3) for target compounds were 0.020-0.072 μg L(-1), 0.035-0.10 μg L(-1) and 0.026-0.076 μg L(-1) in water, milk and honey samples, respectively. In addition, an acceptable reproducibility was achieved by evaluating the repeatability and intermediate precision with relative standard deviations (RSD) of less than 9% and 11%, respectively. Finally, the established AMII-SCSE-HPLC/DAD method was successfully applied for the determination of benzimidazoles residues in milk, honey and environmental water samples. Recoveries obtained for the determination of benzimidazole anthelmintics in spiking samples ranged from 70.2% to 117.6%, with RSD below 12% in all cases. Copyright © 2014 Elsevier B.V. All rights reserved.

Chemistry and Properties of Imide Oligomers from Phenylethynyl-Containing Diamines

NASA Technical Reports Server (NTRS)

Smith, J. G., Jr.; Connell, J. W.

2000-01-01

As an extension of work on pendent phenylethynlyl-containing imide oligomer, three new diamines containing pendent phenylethynyl groups were prepared and characterized. These diamines were used to prepare pendent and pendent and terminal phenylethynyl imide oliogomers via the amide acid route in N-methyl-2-pyrrolidinone at a calculated number average molecular weight of 5000 g mol (exp -1). The pendent phenylethynyl groups were randomly distributed along the oliogomer backbone and provided a means of controlling the distance between reactive sites. The imide oligomers were characterized and thermally cured, and the cured polymers evaluated as thin films and compared with materials of similar composition prepared from 3,5-diamino-4'-phenylethynylbenzophenone. This work was performed as part of a continuing research effort to develop structural resins for potential aeronautical applications.

Decomposition of poly(amide-imide) film enameled on solid copper wire using atmospheric pressure non-equilibrium plasma.

PubMed

Sugiyama, Kazuo; Suzuki, Katsunori; Kuwasima, Shusuke; Aoki, Yosuke; Yajima, Tatsuhiko

2009-01-01

The decomposition of a poly(amide-imide) thin film coated on a solid copper wire was attempted using atmospheric pressure non-equilibrium plasma. The plasma was produced by applying microwave power to an electrically conductive material in a gas mixture of argon, oxygen, and hydrogen. The poly(amide-imide) thin film was easily decomposed by argon-oxygen mixed gas plasma and an oxidized copper surface was obtained. The reduction of the oxidized surface with argon-hydrogen mixed gas plasma rapidly yielded a metallic copper surface. A continuous plasma heat-treatment process using a combination of both the argon-oxygen plasma and argon-hydrogen plasma was found to be suitable for the decomposition of the poly(amide-imide) thin film coated on the solid copper wire.

Interrelation of nonequivalent Csbnd C bonds of naphthalene frame and spatial orientation of substituents: Beta-naphthalene sulfonyl fluoride and beta-naphthalene sulfonyl chloride

NASA Astrophysics Data System (ADS)

Giricheva, Nina I.; Petrov, Vjacheslav M.; Oberhammer, Heinz; Petrova, Valentina N.; Dakkouri, Marwan; Ivanov, Sergey N.; Girichev, Georgiy V.

2013-06-01

β-naphthalene sulfonyl fluoride, β-NaphSF, and β-naphthalene sulfonyl chloride, β-NaphSCl, were studied by gas-phase electron diffraction (GED) and quantum chemical calculations (B3LYP and MP2 in combination with cc-pVDZ, aug-cc-pVDZ and cc-pVTZ basis sets). For each compound the calculations predicted the existence of two conformers which are enantiomers. On the basis of the experimental data it was found that the gas phase over β-NaphSF and NaphSCl at 357(5) K and 395(5) K, respectively, consists of molecular species of C1 symmetry in which the Cβsbnd Ssbnd Hal plane deviates from the perpendicular orientation relative to the naphthalene skeleton plane. The following geometrical parameters (Å and degrees) were obtained from the experiment (uncertainties are in parentheses): rh1(Csbnd H)aver. = 1.097(7), rh1(Csbnd C)aver. = 1.410(3), rh1(Csbnd S) = 1.753(6), rh1(Ssbnd O)aver. = 1.414(4), rh1(Ssbnd F) = 1.559(5), ∠Csbnd Cβsbnd C = 122.8(3), ∠Cβsbnd Ssbnd F = 103.3(30); Φ(Cαsbnd Cβsbnd Ssbnd F) = 104(6) for β-NaphSF, and rh1(Csbnd H)aver. = 1.089(4), rh1(Csbnd C)aver. = 1.411(3), rh1(Csbnd S) = 1.757(5), rh1(Ssbnd O)aver. = 1.419(3), rh1(Ssbnd Сl) = 2.053(4), ∠Csbnd Cβsbnd C = 122.8(1), ∠Cβsbnd Ssbnd Cl = 102.2(7), Φ(Cαsbnd Cβsbnd Ssbnd Cl) = 108(3) for β-NaphSCl. The calculated barriers to internal rotation of the sulfonyl halide groups exceed considerably the thermal energy values corresponding to the temperatures of the GED experiments. Natural bond orbital (NBO) analyses of the electron density distribution were applied to explain the peculiarities of the molecular structure of the studied compounds and the deviation from the structures of their benzene analogs.

Synthesis and characterization of aminated perfluoro polymer electrolytes

NASA Astrophysics Data System (ADS)

Page-Belknap, Zachary Stephan Glenn

Polymer electrolytes have been developed for use in anion exchange membrane fuel cells for years. However, due to the highly corrosive environment within these fuel cells, poor chemical stability of the polymers and low ion conductivity have led to high development costs and thus prevention from widespread commercialization. The work in this study aims to provide a solution to these problems through the synthesis and characterization of a novel polymer electrolyte. The 800 EW 3M PFSA sulfonyl fluoride precursor was aminated with 3-(dimethylamino)-1-propylamine to yield a functional polymer electrolyte following quaternization, referred to in this work as PFSa-PTMa. 1 M solutions of LiPF6, HCL, KOH, NaOH, CsOH, NaHCO3 and Na2CO3 were used to exchange the polymer to alternate counterion forms. Chemical structure analysis was performed using both FT and ATR infrared spectroscopy to confirm sulfonyl fluoride replacement and the absence of sulfonic acid sites. Mechanical testing of the polymer, following counterion exchange with KOH, at saturated conditions and 60 ºC exhibited a tensile strength of 13 +/- 2.0 MPa, a Young's modulus of 87 +/- 16 MPa and a degree of elongation reaching 75% +/- 9.1%, which indicated no mechanical degradation following exposure to a highly basic environment. Conductivities of the polymer in the Cl- and OH- counterion forms at saturated conditions and 90 ºC were observed at 26 +/- 8.0 mS cm-1 and 1.1 +/- 0.1 mS cm-1, respectively. OH- conductivities were slightly above those observed for CO32- and HCO 3- counterions at the same conditions, 0.63 +/- 0.18 and 0.66 +/- 0.21 mS cm-1 respectively. The ion exchange capacity (IEC) of the polymer in the Cl- counterion form was measured via titration at 0.57 meq g-1 which correlated to 11.2 +/- 0.10 water molecules per ion site when at 60ºC and 95% relative humidity. The IEC of the polymer in the OH- counterion form following titration expressed nearly negligible charge density, less than 0.01 meq g -1. The low OH- conductivities and IEC were attributed to the formation of a predominately zwitterionic polymer when exposed to a strong base. Removal of the sulfonamide proton following counterion exchange with a strong base and formation of a zwitterion was confirmed by FTIR with the absence of a primary amine stretch between 3000-3600 cm-1. 1H NMR analysis of small molecule analogues established that the sulfonamide site was not methylated during quaternization as evident by the exclusion of a strong singlet around 2.9 ppm. pH indication tests with Thymolphthalein illuminated the slight presence of free OH- ions within the polymer following counterion exchange thus validating the low IEC and formation of a predominately zwitterionic polymer. Recommended future work with this polymer electrolyte consists of fine tuning the polymer to be less or completely zwitterionic, pKa analysis of the sulfonamide linkage with small molecule analogues, implementation into microbial fuel cell and biological separation processes for pH regulation, and development as a support infrastructure for ionic liquids.

Crystal structures of three indole derivatives: 3-ethnyl-2-methyl-1-phenyl­sulfonyl-1H-indole, 4-phenyl­sulfonyl-3H,4H-cyclo­penta­[b]indol-1(2H)-one and 1-{2-[(E)-2-(5-chloro-2-nitro­phen­yl)ethen­yl]-1-phenyl­sulfonyl-1H-indol-3-yl}ethan-1-one chloro­form monosolvate

PubMed Central

Gopinath, S.; Sethusankar, K.; Ramalingam, Bose Muthu; Mohanakrishnan, Arasambattu K.

2015-01-01

The title compounds, C17H13NO2S, (I), C17H13NO3S, (II), and C24H17ClN2O5S·CHCl3, (III), are indole derivatives. Compounds (I) and (II) crystalize with two independent mol­ecules in the asymmetric unit. The indole ring systems in all three structures deviate only slightly from planarity, with dihedral angles between the planes of the pyrrole and benzene rings spanning the tight range 0.20 (9)–1.65 (9)°. These indole ring systems, in turn, are almost orthogonal to the phenyl­sulfonyl rings [range of dihedral angles between mean planes = 77.21 (8)–89.26 (8)°]. In the three compounds, the mol­ecular structure is stabilized by intra­molecular C—H⋯O hydrogen bonds, generating S(6) ring motifs with the sulfone O atom. In compounds (I) and (II), the two independent mol­ecules are linked by C—H⋯O hydrogen bonds and C—H⋯π inter­actions, while in compound (III), the mol­ecules are linked by C—H⋯O hydrogen bonds, generating R 2 2(22) inversion dimers. PMID:26396842

21 CFR 177.2450 - Polyamide-imide resins.

Code of Federal Regulations, 2011 CFR

2011-04-01

... than 500 parts per million. Residual monomers are determined by gas chromatography (the gas chromatography method titled “Amide-Imide Polymer Analysis—Analysis of Monomer Content,” is incorporated by...

21 CFR 177.2450 - Polyamide-imide resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

... polyamide-imide resins are derived from the condensation reaction of substantially equimolar parts of.... 31957-38-7) derived from the condensation reaction of equimolar parts of benzoyl chloride-3,4...

Phenylethynyl amine

NASA Technical Reports Server (NTRS)

Hergenrother, Paul M. (Inventor); Bryant, Robert G. (Inventor); Jensen, Brian J. (Inventor); Havens, Stephen J. (Inventor)

1997-01-01

Four phenylethynyl amine compounds--3 and 4-aminophenoxy-4'-phenylethynylbenzophenone, and 3 and 4-amino-4'-phenylethynylbenzophenone--were readily prepared and were used to endcap imide oligomers. Phenylethynyl-terminated amide acid oligomers and phenylethynyl-terminated imide oligomers with various molecular weights and compositions were prepared and characterized. These oligomers were cured at 300.degree. C. to 400.degree. C. to provide crosslinked polyimides with excellent solvent resistance, high strength and modulus and good high temperature properties. Adhesive panels, composites, films and moldings from these phenylethynyl terminated imide oligomers gave excellent mechanical performance.

Cooperative dual catalysis: application to the highly enantioselective conjugate cyanation of unsaturated imides.

PubMed

Sammis, Glenn M; Danjo, Hiroshi; Jacobsen, Eric N

2004-08-18

Cooperative heterobimetallic catalysis was used as a design principle to achieve a highly reactive system for the enantioselective conjugate addition of cyanide to alpha,beta-unsaturated imides. A dual-catalyst pathway involving chiral (salen)Al complex 1b and chiral (pybox)Er complex 4b provides measurable improvements in rates and enantioselectivities relative to single-catalyst systems. Mechanistic studies point to a cooperative bimetallic mechanism involving activation of the imide by the Al complex and activation of cyanide by the Er complex.

Synthesis and electronic structure determination of N-alkyl-substituted bis(imino)pyridine iron imides exhibiting spin crossover behavior.

PubMed

Bowman, Amanda C; Milsmann, Carsten; Bill, Eckhard; Turner, Zoë R; Lobkovsky, Emil; DeBeer, Serena; Wieghardt, Karl; Chirik, Paul J

2011-11-02

Three new N-alkyl substituted bis(imino)pyridine iron imide complexes, ((iPr)PDI)FeNR ((iPr)PDI = 2,6-(2,6-(i)Pr(2)-C(6)H(3)-N═CMe)(2)C(5)H(3)N; R = 1-adamantyl ((1)Ad), cyclooctyl ((Cy)Oct), and 2-adamantyl ((2)Ad)) were synthesized by addition of the appropriate alkyl azide to the iron bis(dinitrogen) complex, ((iPr)PDI)Fe(N(2))(2). SQUID magnetic measurements on the isomeric iron imides, ((iPr)PDI)FeN(1)Ad and ((iPr)PDI)FeN(2)Ad, established spin crossover behavior with the latter example having a more complete spin transition in the experimentally accessible temperature range. X-ray diffraction on all three alkyl-substituted bis(imino)pyridine iron imides established essentially planar compounds with relatively short Fe-N(imide) bond lengths and two-electron reduction of the redox-active bis(imino)pyridine chelate. Zero- and applied-field Mössbauer spectroscopic measurements indicate diamagnetic ground states at cryogenic temperatures and established low isomer shifts consistent with highly covalent molecules. For ((iPr)PDI)FeN(2)Ad, Mössbauer spectroscopy also supports spin crossover behavior and allowed extraction of thermodynamic parameters for the S = 0 to S = 1 transition. X-ray absorption spectroscopy and computational studies were also performed to explore the electronic structure of the bis(imino)pyridine alkyl-substituted imides. An electronic structure description with a low spin ferric center (S = 1/2) antiferromagnetically coupled to an imidyl radical (S(imide) = 1/2) and a closed-shell, dianionic bis(imino)pyridine chelate (S(PDI) = 0) is favored for the S = 0 state. An iron-centered spin transition to an intermediate spin ferric ion (S(Fe) = 3/2) accounts for the S = 1 state observed at higher temperatures. Other possibilities based on the computational and experimental data are also evaluated and compared to the electronic structure of the bis(imino)pyridine iron N-aryl imide counterparts.

Synthesis and antimicrobial activity of 1-benzhydryl-sulfonyl-4-(3-(piperidin-4-yl) propyl)piperidine derivatives against pathogens of Lycopersicon esculentum: a structure-activity evaluation study.

PubMed

Vinaya, K; Kavitha, R; Ananda Kumar, C S; Benaka Prasad, S B; Chandrappa, S; Deepak, S A; Nanjunda Swamy, S; Umesha, S; Rangappa, K S

2009-01-01

Several 1-benzhydryl-sulfonyl-4-(3-(piperidin-4-yl)propyl)piperidine derivatives 8(a-j) were prepared by the treatment of substituted benzhydryl chlorides with 4-(3-(piperidin-4-yl)propyl)piperidine followed by N-sulfonation with sulfonyl chlorides in the presence of dry methylene dichloride and triethyl amine. The synthesized compounds were characterized by (1)H-NMR, IR, and elemental analysis. All the synthesized compounds were evaluated in vitro for their efficacy as antimicrobial agents by artificial inoculation technique against standard strains of two important bacterial viz., Xanthomonas axonopodis pv. vesicatoria and Ralstonia solanacearum as well as and two fungal pathogens namely Alternaria solani and Fusarium solani of tomato plants. We have briefly investigated the structure-activity relation studies and reveal that the nature of substitutions on benzhydryl ring and sulfonamide ring influences the antibacterial activity. Among the synthesized new compounds 8b, 8d, 8g, 8h, 8i, and 8j were showed significant potent antimicrobial activities compared to the standard drugs chloramphenicol, mancozeb.

Rhodium/Silver-Cocatalyzed Transannulation of N-Sulfonyl-1,2,3-triazoles with Vinyl Azides: Divergent Synthesis of Pyrroles and 2 H-Pyrazines.

PubMed

Zhang, Lin; Sun, Ge; Bi, Xihe

2016-11-07

The first cyclization reaction between vinyl azides and N-sulfonyl-1,2,3-triazoles is reported. A Rh/Ag binary metal catalyst system proved to be necessary for the successful cyclization. By varying the structure of vinyl azides, such reaction allows the divergent synthesis of pyrroles and 2H-pyrazines. The cyclization reactions feature a broad substrate scope, good functional group tolerance, high reaction efficiency, and good to high product yields. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Sex-related difference in the inductions by perfluoro-octanoic acid of peroxisomal beta-oxidation, microsomal 1-acylglycerophosphocholine acyltransferase and cytosolic long-chain acyl-CoA hydrolase in rat liver.

PubMed Central

Kawashima, Y; Uy-Yu, N; Kozuka, H

1989-01-01

Inductions by perfluoro-octanoic acid (PFOA) of hepatomegaly, peroxisomal beta-oxidation, microsomal 1-acylglycerophosphocholine acyltransferase and cytosolic long-chain acyl-CoA hydrolase were compared in liver between male and female rats. Marked inductions of these four parameters were seen concurrently in liver of male rats, whereas the inductions in liver of female rats were far less pronounced. The sex-related difference in the response of rat liver to PFOA was much more marked than that seen with p-chlorophenoxyisobutyric acid (clofibric acid) or 2,2'-(decamethylenedithio)diethanol (tiadenol). Hormonal manipulations revealed that this sex-related difference in the inductions is strongly dependent on sex hormones, namely that testosterone is necessary for the inductions, whereas oestradiol prevented the inductions by PFOA. PMID:2570571

Viscosity effects on the thermal decomposition of bis(perfluoro-2-N-propoxypropionyl) peroxide in dense carbon dioxide and fluorinated solvents.

PubMed

Bunyard, W C; Kadla, J F; DeYoung, J; DeSimone, J M

2001-08-01

The thermal decomposition of the free-radical initiator bis(perfluoro-2-N-propoxyprionyl) peroxide (BPPP) was studied in dense carbon dioxide and a series of fluorinated solvents. For the fluorinated solvents, the observed first-order decomposition rate constants, k(obs), increased with decreasing solvent viscosity, suggesting a single-bond decomposition mechanism. The k(obs) values are comparatively larger in dense carbon dioxide and similar to the "zero-viscosity" rate constants extrapolated from the decomposition kinetics in the fluorinated solvents. The decomposition activation parameters demonstrate a compensation behavior of the activation enthalpy with the activation entropy upon change in solvent viscosity. Comparison of the change in activation parameter values upon change in solvent viscosity for BPPP with two additional initiators, acetyl peroxide (AP) and trifluoroacetyl peroxide (TFAP), further suggests that carbon dioxide exerts a very minimal influence on the decomposition mechanism of these initiators through solvent-cage effects.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, Sadananda; Brown, Suree S.; Mayes, Richard T.

A new series of amidoxime-based polymer adsorbents were synthesized at the Oak Ridge National Laboratory (ORNL) by electron beam induced grafting of acrylonitrile and itaconic acid onto polyethylene fiber. Hydroxylamine derivatives of poly(acrylonitrile) (PAN) moiety are demonstrated to possess two kinds of functional groups: open-chain amidoxime and cyclic imide dioxime. The open-chain amidoxime is shown to convert to imide dioxime on heat treatment in the presence of an aprotic solvent, like dimethylsulfoxide (DMSO). The formation of amidoxime and imide dioxime was confirmed by 13-C CPMAS spectra. The adsorbents were evaluated for uranium adsorption efficiency at ORNL with simulated seawater spikedmore » with 8 ppm uranium and 5 gallon seawater in a batch reactor, and in flow-through columns with natural seawater at the Marine Science Laboratory (MSL) of Pacific Northwest National Laboratory (PNNL) at Sequim Bay, WA. The DMSO-heat-treated sorbents adsorbed uranium as high as 4.48 g-U/kg-ads. from seawater. Experimental evidence is presented that the poly(imide dioxime) is primarily responsible for enhanced uranium adsorption capacity from natural seawater. The conjugated system in the imide dioxime ligand possesses increased electron donation ability, which is believed to significantly enhance the uranyl coordination in seawater« less

Central neurotoxicity of immunomodulatory drugs in multiple myeloma.

PubMed

Patel, Urmeel H; Mir, Muhammad A; Sivik, Jeffrey K; Raheja, Divisha; Pandey, Manoj K; Talamo, Giampaolo

2015-02-24

Immunomodulatory drugs (IMiDs) currently used in the treatment of multiple myeloma, are thalidomide, lenalidomide and pomalidomide. One of the most common side effects of thalidomide is neurotoxicity, predominantly in the form of peripheral neuropathy. We report 6 cases of significant central neurotoxicity associated with IMiD therapy. Treatment with thalidomide (1 patient), lenalidomide (4 patients), and pomalidomide (1 patient) was associated with various clinical manifestations of central neurotoxicity, including reversible coma, amnesia, expressive aphasia, and dysarthria. Central neurotoxicity should be recognized as an important side effect of IMiD therapy.

Central Neurotoxicity of Immunomodulatory Drugs in Multiple Myeloma

PubMed Central

Patel, Urmeel H.; Mir, Muhammad A.; Sivik, Jeffrey K.; Raheja, Divisha; Pandey, Manoj K.; Talamo, Giampaolo

2015-01-01

Immunomodulatory drugs (IMiDs) currently used in the treatment of multiple myeloma, are thalidomide, lenalidomide and pomalidomide. One of the most common side effects of thalidomide is neurotoxicity, predominantly in the form of peripheral neuropathy. We report 6 cases of significant central neurotoxicity associated with IMiD therapy. Treatment with thalidomide (1 patient), lenalidomide (4 patients), and pomalidomide (1 patient) was associated with various clinical manifestations of central neurotoxicity, including reversible coma, amnesia, expressive aphasia, and dysarthria. Central neurotoxicity should be recognized as an important side effect of IMiD therapy. PMID:25852850

New organic semiconductors with imide/amide-containing molecular systems.

PubMed

Liu, Zitong; Zhang, Guanxin; Cai, Zhengxu; Chen, Xin; Luo, Hewei; Li, Yonghai; Wang, Jianguo; Zhang, Deqing

2014-10-29

Due to their high electron affinities, chemical and thermal stabilities, π-conjugated molecules with imide/amide frameworks have received considerable attentions as promising candidates for high-performance optoelectronic materials, particularly for organic semiconductors with high carrier mobilities. The purpose of this Research News is to give an overview of recent advances in development of high performance imide/amide based organic semiconductors for field-effect transistors. It covers naphthalene diimide-, perylene diimide- and amide-based conjugated molecules and polymers for organic semiconductors. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Clinical and economic analysis of an internal medicine-infectious disease department at a university general hospital (2005-2006)].

PubMed

Gómez, Joaquín; García-Vázquez, Elisa; Antonio Puertas, José; Ródenas, Julio; Herrero, José Antonio; Albaladejo, Carmen; Baños, Víctor; Canteras, Manuel; Alcaraz, Manolo

2009-02-01

Comparative study in patients with infectious diseases admitted to a specialized Internal Medicine-Infectious Diseases Department (IMID) versus those admitted to other medical departments in a university general hospital, investigating quality and cost-effectiveness. Analysis of patients in 10 principle diagnosis-related groups (DRGs) of infectious diseases admitted to the IMID were compared to those admitted to other medical departments (2005-2006). The DRG were divided in 4 main groups: respiratory infections (DGR 88, 89, 90, 540), urinary infections (DRG 320, 321), sepsis (DRG 416, 584), and skin infections (DRG 277, 278). For each group, quality variables (mortality and readmission rate), efficacy variables (mean hospital stay and mean DRG-based cost per patient) and complexity variables (case mix, relative weight, and functional index) were analyzed. 542 patients included in the 10 main infectious disease DRGs were admitted to IMID and 2404 to other medical departments. After adjusting for DRG case mix (case mix 0.99 for IMID and 0.89 for others), mean hospital stay (5.11 days vs. 7.65 days), mortality (3.5% vs. 7.9%) and mean DRG-based economic cost per patient (1521euro/patient vs. 2952euro/patient) was significantly lower in the group of patients hospitalized in IMID than the group in other medical departments (p<0.05). The readmission rate was similar in the 2 groups (5.5% and 6.5%, respectively). The results per each DRG group were similar to the overall results. For a similar case mix, hospitalization in IMID departments had a positive influence on the variables analyzed as compared to hospitalization in other departments, with a shorter mean stay, lower mortality, and lower mean DRG-based economic cost per patient. Creation and development of IMID departments should be an essential objective to improve healthcare quality and respond to social demands.

Poly(Amide-imide) Aerogel Materials Produced via an Ice Templating Process

PubMed Central

Gawryla, Matthew D.; Arndt, Eric M.

2018-01-01

Low density composites of sodium montmorillonite and poly(amide-imide) polymers have been created using an ice templating method, which serves as an alternative to the often-difficult foaming of high temperature/high performance polymers. The starting polymer was received in the poly(amic acid) form which can be cured using heat, into a water insoluble amide-imide copolymer. The resulting materials have densities in the 0.05 g/cm3 range and have excellent mechanical properties. Using a tertiary amine as a processing aid provides for lower viscosity and allows more concentrated polymer solutions to be used. The concentration of the amine relative to the acid groups on the polymer backbone has been found to cause significant difference in the mechanical properties of the dried materials. The synthesis and characterization of low density versions of two poly(amide-imide) polymers and their composites with sodium montmorillonite clay are discussed in the present work. PMID:29401663

Poly(Amide-imide) Aerogel Materials Produced via an Ice Templating Process.

PubMed

Gawryla, Matthew D; Arndt, Eric M; Sánchez-Soto, Miguel; Schiraldi, David A

2018-02-03

Low density composites of sodium montmorillonite and poly(amide-imide) polymers have been created using an ice templating method, which serves as an alternative to the often-difficult foaming of high temperature/high performance polymers. The starting polymer was received in the poly(amic acid) form which can be cured using heat, into a water insoluble amide-imide copolymer. The resulting materials have densities in the 0.05 g/cm³ range and have excellent mechanical properties. Using a tertiary amine as a processing aid provides for lower viscosity and allows more concentrated polymer solutions to be used. The concentration of the amine relative to the acid groups on the polymer backbone has been found to cause significant difference in the mechanical properties of the dried materials. The synthesis and characterization of low density versions of two poly(amide-imide) polymers and their composites with sodium montmorillonite clay are discussed in the present work.

Synthesis, Characterization, Topographical Modification, and Surface Properties of Copoly(Imide Siloxane)s

NASA Technical Reports Server (NTRS)

Wohl, Christopher J.; Atkins, Brad M.; Belcher, Marcus A.; Connell, John W.

2012-01-01

Novel copoly(imide siloxane)s were synthesized from commercially available aminopropyl terminated siloxane oligomers, aromatic dianhydrides, and diamines. This synthetic approach produced copolymers with well-defined siloxane blocks linked with imide units in a random fashion. The copoly(amide acid)s were characterized by solution viscosity and subsequently used to cast thin films followed by thermal imidization in an inert atmosphere. Thin films were characterized using contact angle goniometry, attenuated total reflection Fourier transform infrared spectroscopy, confocal and optical microscopy, and tensile testing. Adhesion of micronsized particles was determined quantitatively using a sonication device. The polydimethylsiloxane (PDMS) moieties lowered the copolymer surface energy due to migration of siloxane moieties to the film s surface, resulting in a notable reduction in particle adhesion. A further reduction in particle adhesion was achieved by introducing topographical features on a scale of several to tens of microns by a laser ablation technique.

Design, synthesis, and evaluation of cyclic amide/imide-bearing hydroxamic acid derivatives as class-selective histone deacetylase (HDAC) inhibitors.

PubMed

Shinji, Chihiro; Maeda, Satoko; Imai, Keisuke; Yoshida, Minoru; Hashimoto, Yuichi; Miyachi, Hiroyuki

2006-11-15

A series of hydroxamic acid derivatives bearing a cyclic amide/imide group as a linker and/or cap structure, prepared during our structural development studies based on thalidomide, showed class-selective potent histone deacetylase (HDAC)-inhibitory activity. Structure-activity relationship studies indicated that the steric character of the substituent introduced at the cyclic amide/imide nitrogen atom, the presence of the amide/imide carbonyl group, the hydroxamic acid structure, the shape of the linking group, and the distance between the zinc-binding hydroxamic acid group and the cap structure are all important for HDAC-inhibitory activity and class selectivity. A representative compound (30w) showed potent p21 promoter activity, comparable with that of trichostatin A (TSA), and its cytostatic activity against cells of the human prostate cell line LNCaP was more potent than that of the well-known HDAC inhibitor, suberoylanilide hydroxamic acid (SAHA).

Direct Electrodeposition of UO2 from Uranyl Bis(trifluoromethanesulfonyl)imide Dissolved in 1-Ethyl-3-methylimidazolium Bis(trifluoromethanesulfonyl)imide Room Temperature Ionic Liquid System

DOE PAGES

Freiderich, John W.; Wanigasekara, Eranda P.; Sun, Xiao-Guang; ...

2013-11-11

Our study demonstrates a direct electrodeposition of UO 2 at a Pt cathode from a solution of uranyl bis(trifluoromethanesulfonyl)imide [UO 2(NTf 2) 2)] in a bulk room-temperature ionic liquid (RTIL), 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (EMIM +NTf 2 –). Cyclic voltammetry (CV) studies revealed two reduction waves corresponding to the conversion of uranium(VI) to uranium(IV), and a mechanism for the overall electroreduction is proposed. A controlled-potential experiment was performed, holding the reduction potential at–1.0 V for 24 h to obtain a brown-black deposit of UO 2 on the Pt cathode. The Faradaic efficiency of the reduction process was determined to be >80%. Themore » UO 2deposit was characterized by powder X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS).« less

Organic-Inorganic Hybrids Using Novel Phenylethynyl Imide Silanes

NASA Technical Reports Server (NTRS)

Park, C.; Lowther, S. E.; Smith, J. G., Jr.

2001-01-01

In this presentation, polyimide-silica hybrids using novel phenylethynyl imide silanes are reported. The phenylethynyl group is present in the organic precursor as either a pendent or an end group to bond chemically with the polyimide adhesive containing phenylethynyl groups during processing, while the silane group of the organic precursor would chemically react with the inorganic precursor through oxane bond formation. The chemical compositions of these novel hybrids were examined using X-ray mapping modes of scanning electron microscopy (SEM), which revealed a silicon gradient interphase between the high surface energy substrate and the polyimide adhesive. Novel aromatic phenylethynyl imide silanes (APEISs) and pendent phenylethynyl imide oligomeric disilanes (PPEIDSs) have been synthesized, and sol-gel solutions containing the new silanes, a phenylethynyl terminated imide oligomer (PETI-5), and an inorganic precursor were formulated to develop a gradient hybrid interphase between a titanium alloy and the adhesive. Two different sol-gel systems were investigated to develop organic-inorganic hybrids. Hybrid I was composed of an organic precursor containing both phenylethynyl and silane groups (PPEIDS) and an inorganic precursor. Functional group concentrations were controlled by the variation of the molecular weight of the imide backbone of PPEIDS. Hybrid II was composed of organic and inorganic precursors and a coupling agent containing both phenylethynyl and silane groups. Morphology and chemical composition of the hybrid interphase between the inorganic substrate and the adhesive were investigated, and the bond strength and durability were evaluated using lap shear tests at various conditions. The assessment of how the bonding at an interface is affected by various sol-gel solution compositions and environments is reported.

Wholly Aromatic Ether-imides. Potential Materials for n-Type Semiconductors

NASA Technical Reports Server (NTRS)

Dingemans, Theo J.; St.Clair, Terry L.; Samulski, Edward T.; Bushnell, Dennis M. (Technical Monitor)

2002-01-01

We report on the synthesis and characterization of a novel series low-molar-mass ether-imide rod-shaped model compounds. All ether-imides were obtained by terminating the appropriate rigid core dianhydride, i.e. pyromellitic dianhydride (PMDA), 1,4,5,8-naphthalenetetracarboxylic dianhydride (NDA), 3,3',4,4'-biphenyltetracarboxylic dianhydride (BPDA), and 3,3,4,4'-oxydiphthalic dianhydride (ODPA) with three flexible aryl-ether tails of different chain length. The mono-functional aryl-ether amines, i.e. 4-(3-phenoxy-phenoxy)-phenylamine (2) and 4-(3-phenoxy-3-phenoxy-phenoxy)-phenylamine (4), were synthesized using standard fluoro-displacement and Ullmann condensation techniques. The corresponding ether-imide model compounds were obtained in high yields using a one-step solution imidization procedure. Increasing the number of meta-substituted aryl-ether units reduces the melt transition temperatures and at the same time it increases the solubility of the model compounds. Most model compounds are crystalline solids and form isotropic melts upon heating. 2,7-Bis-(-4-phenoxy-phenyl)-benzo[Imn][3,8]phenanthroline1,3,6,8-tetraone (NDA-n0), however, displays a smectic A (SA) when cooled from the isotropic phase, followed by what appears to be either a highly ordered smectic phase or a, columnar phase. This is the first example, known to date, in which a mesophase is detected in a wholly aromatic ether-imide compound. For all compounds we present spectroscopic data and X-ray diffraction data. Cyclic voltammetry was used to determine the redox behavior and pertinent energy levels of the model compounds.

Thermosetting Phthalocyanine Polymers

NASA Technical Reports Server (NTRS)

Fohlen, G.; Parker, J.; Achar, B.

1985-01-01

Group of phthalocyanine polymers resist thermal degradation. Polymers expected semiconducting. Principal applications probably in molded or laminated parts that have to withstand high temperatures. Polymers made from either of two classes of monomer: Bisphthalonitriles with imide linkages or Bisphthalonitriles with ester-imide linkages.

Improved profiling of estrogen metabolites by orbitrap LC/MS

PubMed Central

Li, Xingnan; Franke, Adrian A.

2015-01-01

Estrogen metabolites are important biomarkers to evaluate cancer risks and metabolic diseases. Due to their low physiological levels, a sensitive and accurate method is required, especially for the quantitation of unconjugated forms of endogenous steroids and their metabolites in humans. Here, we evaluated various derivatives of estrogens for improved analysis by orbitrap LC/MS in human serum samples. A new chemical derivatization reagent was applied modifying phenolic steroids to form 1-methylimidazole-2-sulfonyl adducts. The method significantly improves the sensitivity 2–100 fold by full scan MS and targeted selected ion monitoring MS over other derivatization methods including, dansyl, picolinoyl, and pyridine-3-sulfonyl products. PMID:25543003

The synthesis and structures of 1,1'-bis(sulfonyl)ferrocene derivatives.

PubMed

Chanawanno, Kullapa; Holstrom, Cole; Crandall, Laura A; Dodge, Henry; Nemykin, Victor N; Herrick, Richard S; Ziegler, Christopher J

2016-09-28

A series of 1,1'-bis(sulfonyl)ferrocene compounds were produced via the 1,1'-bis(sulfonate)ferrocene ammonium salt. This compound can be readily converted to 1,1' bis(sulfonylchloride)ferrocene. By varying stoichiometry and reaction times, both mono- and bis-sulfonamide derivatives can be synthesized. All new compounds presented in this report have been structurally characterized. The structures of the bis-sulfonamide systems are similar to the well-studied bis(amide) ferrocene compounds. Intermolecular hydrogen bonding is observed, typically between NH and SO groups of neighboring sulfonamides. However in the bis(GABA) derivative, intermolecular NH to CO hydrogen bonding interactions are present.

The divergent synthesis of nitrogen heterocycles by rhodium(II)-catalyzed cycloadditions of 1-sulfonyl 1,2,3-triazoles with 1,3-dienes.

PubMed

Shang, Hai; Wang, Yuanhao; Tian, Yu; Feng, Juan; Tang, Yefeng

2014-05-26

The first rhodium(II)-catalyzed aza-[4+3] cycloadditions of 1-sulfonyl 1,2,3-triazoles with 1,3-dienes have been developed, and enable the efficient synthesis of highly functionalized 2,5-dihydroazepines from readily available precursors. In some cases, the reaction pathway could divert to formal aza-[3+2] cycloadditions, thus leading to 2,3-dihydropyrroles. In this context, the titled reaction represents a capable tool for the divergent synthesis of two types of synthetically valuable aza-heterocycles from common rhodium(II) iminocarbene intermediates. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Thermally Induced Denitrogenative Annulation for the Synthesis of Dihydroquinolinimines and Chroman-4-imines.

PubMed

Chou, Chih-Hung; Chen, Ying-Yu; Rajagopal, Basker; Tu, Hsiu-Chung; Chen, Kuan-Lin; Wang, Sheng-Fu; Liang, Chien-Fu; Tyan, Yu-Chang; Lin, Po-Chiao

2016-03-04

A rapid growth in synthetic methods for the preparation of diverse organic molecules using N-sulfonyl-1,2,3-triazoles is of great interest in organic synthesis. Transition metals are generally used to activate the α-imino diazo intermediates. Metal-free methods have not been studied in detail, but can be a good complement to transition metal catalysis in the mild reaction conditions. We herein report a novel method for the preparation of 2,3-dihydroquinolin-4-imine and chroman-4-imine analogs from their corresponding N-sulfonyl-1,2,3-triazoles in the absence of metal catalysts. To achieve intramolecular annulation, the introduction of an electron-donating group is required at the meta position of N-sulfonyl-1,2,3-triazole methyl anilines. The inclusion of tailored substituents on the aniline moieties and nitrogen atoms enhances the nucleophilicity of the phenyl π-electrons, thus allowing them to undergo a Friedel-Crafts-type reaction with the highly electrophilic ketenimines. This metal-free method was carefully optimized to generate a variety of dihydroquinolin-4-imines and chroman-4-imines in moderate-to-good yields. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Phosphorus-containing imide resins

NASA Technical Reports Server (NTRS)

Varma, I. K.; Fohlen, G. M.; Parker, J. A. (Inventor)

1985-01-01

Cured polymers of bis and tris-imides derived from tris(m-aminophenyl) phosphine oxides by reaction with maleic anhydride or its derivatives, and addition polymers of such imides, including a variant in which a monoimide is condensed with a dianhydride and the product is treated with a further quantity of maleic anhydride prior to curing are disclosed and claimed. Such polymers are flame resistant. Also disclosed are an improved method of producing tris(m-aminophenyl) phosphine oxides from the nitro analogues by reduction with hydrazine hydrate using palladized charcoal or Raney nickel as the catalyst and fiber reinforced cured resin composites.

Dispersion polymerization of L-lactide utilizing ionic liquids as reaction medium

NASA Astrophysics Data System (ADS)

Fahmiati, Sri; Minami, Hideto; Haryono, Agus; Adilina, Indri B.

2017-11-01

Dispersion polymerization of L-lactide was proceeded in various ionic liquids. Ionic liquids as 1-Hexyl-3-methylimidazolium bis (trifluormethylsulfonyl) imide, [HMIM] [TFSI], 1-Butyl-3-methylimidazolium bis (trifluoromethylsulfonyl) imide, [BMP] [TFSI], and N,N,N-Trimethyl-N-Propylammonium Bis (trifloromethanesulfonyl) imide, [TMPA] [TFSI], were employed as reaction medium that dissolved both of lactide and stabilizer (polyvinylprrolidone). Sn-supported on bentonite was used as a ring opening catalyst of L-lactide. Gel Permeation Chromatography result showed that poly-(L-lactic acid) were formed in ionic liquids [HMIM] [TFSI] and [BMP] [TFSI] with molecular weight as 19390 and 20844, respectively.

Selective α-arylation of α,β-unsaturated imides mediated by a visible light photoredox catalyst.

PubMed

Ando, Yuki; Kamatsuka, Takuto; Shinokubo, Hiroshi; Miyake, Yoshihiro

2017-08-10

Visible light-mediated α-arylation of α,β-unsaturated imides is achieved via aminium radicals generated from diarylalkylamines using a photoredox catalyst. On the basis of emission quenching experiments, a plausible pathway of the reaction is discussed.

In Situ Poling and Imidization of Amorphous Piezoelectric Polyimides

NASA Technical Reports Server (NTRS)

Park, Cheol; Ounaies, Zoubeida; Wise, Kristopher E.; Harrison, Joycelyn S.; Bushnell, Dennis M. (Technical Monitor)

2002-01-01

An amorphous piezoelectric polyimide containing polar functional groups has been developed using a combination of experimental and molecular modeling for potential use in high temperature applications. This amorphous polyimide, (Beta-CN)APB/ODPA, has exhibited good thermal stability and piezoelectric response at temperatures up to 150C. Density functional calculations predicted that a partially cured amic acid (open imide ring) possesses a dipole moment four times larger than the fully imidized closed ring. In situ poling and imidization of the partially cured (Beta-CN)APB/ODPA, was studied in an attempt to maximize the degree of dipolar orientation and the resultant piezoelectric response. A positive corona poling was used to minimize localized arcing during poling and to allow use of higher poling fields without dielectric breakdown. The dielectric relaxation strength, remanent polarization, and piezoelectric response were evaluated as a function of the poling profile. The partially cured, corona poled polymers exhibited higher dielectric relaxation strength (delta varepsilon), remanent polarization (Pr) and piezoelectric strain coefficient (d33) than the fully cured, conventionally poled ones.

Solvent extraction separation of Th-227 and Ac-225 in room temperature ionic liquids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bell, Jason R; Boll, Rose Ann; Dai, Sheng

2012-01-01

The solvent extractions of Th-227 and Ac-225 from the aqueous phase into ionic liquids (ILs) were investigated by using N,N,N ,N - tetraoctyldiglycolamide (TODGA) or di(2-ethylhexyl)phosphoric acid (HDEHP) as an extractant. Four ionic liquids, 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([C4mim][NTf2]), 1-butyl-3-methylimidazolium bis(perfluoroethanesulfonyl)imide ([C4mim][BETI]), 1-butyl-2,3-trimethyleneimidazolium (trifluoromethanesulfonyl)imide [BuI5][NTf2], and 1-benzyl pyridinium bis(trifluoromethanesulfonyl)imide ([PhCH2Py][NTf2]) were used as extraction solvents for separation of Th-227 and Ac-225 in this study. Excellent extraction efficiencies and selectivities were found for Th-227/Ac-225 when HDEHP was used as an extractant in these ionic liquids. The effects of different extractant concentrations in ionic liquids and acidities of the aqueous phase on extraction efficienciesmore » and selectivities of Th-227/Ac-225 are also presented in this article.« less

Determination of fluorotelomer alcohols in selected consumer products and preliminary investigation of their fate in the indoor environment.

PubMed

Liu, Xiaoyu; Guo, Zhishi; Folk, Edgar E; Roache, Nancy F

2015-06-01

The U.S. Environmental Protection Agency (EPA) has established an ongoing effort to identify the major perfluorocarboxylic acid (PFCA) sources in nonoccupational indoor environments and characterize their transport and fate. This study determined the concentrations of fluorotelomer alcohols (FTOHs), which are the precursors to PFCAs, in fifty-four consumer products collected from the U.S. open market in the years of 2011 and 2013. The products included carpet, commercial carpet-care liquids, household carpet/fabric-care liquids, treated apparel, treated home textiles, treated non-woven medical garments, floor waxes, food-contact paper, membranes for apparel, and thread-sealant tapes. The FTOHs quantified were 1H,1H,2H,2H-perfluoro-1-octanol (6:2 FTOH), 1H,1H,2H,2H-perfluoro-1-decanol (8:2 FTOH), and 1H,1H,2H,2H-perfluoro-1-dodecanol (10:2 FTOH). The content of 6:2 FTOH ranged from non-delectable to 331μgg(-1), 8:2 FTOH from non-delectable to 92μgg(-1), and 10:2 FTOH from non-detectable to 24μgg(-1). In addition, two consumer products from the home textile category were tested in the washing-drying process. One product from the treated apparel category and one from the home textile category were tested in the micro-scale chamber under elevated temperatures. The experimental data show that the washing-drying process with one cycle did not significantly reduce the FTOH concentrations in the tested consumer products. FTOH off-gassing was observed under accelerated aging conditions. Future tests should include air sampling to allow determination of the absolute emission rates at different temperatures. The results of this study should be informative to exposure assessment and risk management. Published by Elsevier Ltd.

Near Infrared Phosphorescent, Non-oxidizable Palladium and Platinum Perfluoro-phthalocyanines.

PubMed

Łapok, Łukasz; Obłoza, Magdalena; Gorski, Alexandr; Knyukshto, Valeri; Raichyonok, Tamara; Waluk, Jacek; Nowakowska, Maria

2016-04-18

New Pd(II) and Pt(II) complexes with a highly electron-deficient ligand (H2 PcF64 ) were conveniently prepared in a three-step synthesis. This is the first time that the phosphorescence of phthalocyanines with a H2 PcF64 framework has been measured. Based on these measurements, the triplet-state energies (ET ) were directly determined. Transient absorption experiments revealed broad T1 →Tn absorption spanning from ca. 350 to ca. 1000 nm and allowed determination of the triplet-state lifetimes. Removal of the Pd or Pt from the perfluoro-phthalocyanine resulted in a significant increase of the triplet lifetime for H2 PcF64 . The very efficient intersystem crossing observed for both PdPcF64 and PtPcF64 leads to residual fluorescence and suppresses the fluorescence lifetimes to less than 50 ps. The absence of Pd and Pt in the perfluoro-phthalocyanine ligand, viz. H2 PcF64 , led to a recovery of fluorescence. Cyclic voltamperometry studies pointed to complete resistance of PdPcF64 and PtPcF64 to oxidation and very strong electron affinity, which rendered these materials very good electron acceptors (n-type materials). The presence of d-orbital metals such as Pd(II) and Pt(II) in the phthalocyanine ring stabilizes their reduced forms, as indicated by the spectroelectrochemical experiments. PdPcF64 and PtPcF64 easily sensitize singlet oxygen production with very high quantum yields. Both phthalocyanines presented resistance to photodegradation in the solid state under aerobic conditions and under intense irradiation. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Promoting Retention through the Implementation of Integrated Multicultural Instructional Design

ERIC Educational Resources Information Center

Higbee, Jeanne L.; Goff, Emily; Schultz, Jennifer L.

2013-01-01

This article introduces the guiding principles of integrated multicultural instructional design (IMID), a new pedagogical model created to promote retention by addressing multicultural perspectives and social justice issues across the curriculum. To illustrate the model, specific strategies for implementing IMID in a content-based,…

An Efficient Synthesis of de novo Imidates via Aza-Claisen Rearrangements of N-Allyl Ynamides

PubMed Central

DeKorver, Kyle A.; North, Troy D.; Hsung, Richard P.

2010-01-01

A novel thermal 3-aza-Claisen rearrangement of N-allyl ynamides for the synthesis of α-allyl imidates is described. Also, a sequential aza-Claisen, Pd-catalyzed Overman rearrangement is described for the synthesis of azapine-2-ones. PMID:21278848

Diffusion of dioxygen in 1-alkenes and biphenyl in perfluoro- n-alkanes

NASA Astrophysics Data System (ADS)

Kowert, Bruce A.; Sobush, Kurtis T.; Dang, Nhan C.; Seele, Louis G., III; Fuqua, Chantel F.; Mapes, Courtney L.

2002-02-01

The translational diffusion constant, D, has been measured for O 2 in the even 1-alkenes 1-C 6H 12 to 1-C 16H 32 and biphenyl in n-C 6F 14 and n-C 9F 20. Deviations from the Stokes-Einstein relation were found; the use of D/ T= A/ ηp gave p=0.560±0.017 for O 2 in the 1-alkenes, the same (within experimental error) as found previously for O 2 in the n-alkanes. The charge transfer (CT) transition used to detect O 2 in the 1-alkenes is at 220 nm. The D values for biphenyl in the perfluoro- n-alkanes (PFAs) are consistent with those in the n-alkanes, where p=0.718±0.004. These results suggest that O 2 has similar solute-solvent interactions in both the 1-alkenes and n-alkanes as does biphenyl in the n-alkanes and PFAs.

Thermodynamic parameters of phase transitions of perfluoro-N-(4-methylcyclohexyl)piperidine

NASA Astrophysics Data System (ADS)

Druzhinina, A. I.; Efimova, A. A.; Varushchenko, R. M.; Chelovskaya, N. V.

2007-12-01

The heat capacity of perfluoro-N-(4-methylcyclohexyl)piperidine (PMCP) was measured by low-temperature adiabatic calorimetry. The purity of the substance ( N 1 = 99.66 mol %), triple point temperature ( T tp = 293.26 K), and enthalpy of fusion (Δfus H {m/°} = 8.32 kJ/mol) were determined. The enthalpy of vaporization was measured by calorimetry at 298.15 K (Δvap H {m/°}(298.15 K) = 56.56 kJ/mol). The temperature dependence of the saturated vapor pressure of PMCP over the pressure range 6.2-101.6 kPa was determined by comparative ebulliometry. The normal boiling point ( T n.b. = 460.74 K), ehthalpies of vaporization (at various temperatures), and critical parameters of PMCP were calculated. The calculated and experimental values of Δvap H {m/°}(298.15 K) agree to within measurement errors, which proves the reliability of these values and pT parameters used in calculations.

High Temperature VARTM of Phenylethynyl Terminated Imides

NASA Technical Reports Server (NTRS)

Ghose, Sayata; Watson, Kent A.; Cano, Roberto J.; Britton, Sean M.; Jensen, Brian J.; Connell, John W.; Herring, Helen M.; Linberry, Quentin J.

2009-01-01

LaRC phenylethynyl terminated imide (PETI) resins were processed into composites using high temperature vacuum assisted resin transfer molding (VARTM). Although initial runs yielded composites with high void content, process modifications reduced voids to <3%. Photomicrographs were taken and void contents and T(sub g)s of the panels were determined.

Methyl-sulfonyl-methane (MSM)-induced acute angle closure.

PubMed

Hwang, Jeremy C; Khine, Kay T; Lee, Jennifer C; Boyer, David S; Francis, Brian A

2015-01-01

To report the first case of presumed bilateral acute angle closure (AAC) secondary to ingestion of the dietary supplement, methyl-sulfonyl-methane (MSM). A 35-year-old woman presented with bilateral AAC 1 week after starting multiple dietary supplements, one of which contained MSM. Ultrasound biomicroscopy demonstrated bilateral anterior rotation of the iris-lens diaphragm, ciliary body edema, and choroidal effusion. Four days after discontinuation of the supplements, her angle closure and uveal effusion resolved, and her best-corrected vision recovered to 20/20 bilaterally. Sulfa-based drugs have been reported to cause AAC, choroidal effusion, and ciliary body edema. In our patient, the coincidence of bilateral AAC with choroidal and ciliary body effusion that began 1 week after starting dietary supplements was suspicious for drug-induced AAC. The dietary supplement Basic Detox Nutrients contains MSM, the only constituent in the patient's medication list with a sulfonyl moiety. Given the similarities in chemical structure and clinical presentation, we postulate that MSM induces AAC in a manner similar to mechanisms previously described for other sulfa-based drugs. As MSM continues to be used and studied for its anti-inflammatory and antioxidative properties, investigators and marketers will need to be cognizant of its potential to cause AAC and provide proper warning to consumers.

Calculated Third Order Rate Constants for Interpreting the Mechanisms of Hydrolyses of Chloroformates, Carboxylic Acid Halides, Sulfonyl Chlorides and Phosphorochloridates

PubMed Central

Bentley, T. William

2015-01-01

Hydrolyses of acid derivatives (e.g., carboxylic acid chlorides and fluorides, fluoro- and chloroformates, sulfonyl chlorides, phosphorochloridates, anhydrides) exhibit pseudo-first order kinetics. Reaction mechanisms vary from those involving a cationic intermediate (SN1) to concerted SN2 processes, and further to third order reactions, in which one solvent molecule acts as the attacking nucleophile and a second molecule acts as a general base catalyst. A unified framework is discussed, in which there are two reaction channels—an SN1-SN2 spectrum and an SN2-SN3 spectrum. Third order rate constants (k3) are calculated for solvolytic reactions in a wide range of compositions of acetone-water mixtures, and are shown to be either approximately constant or correlated with the Grunwald-Winstein Y parameter. These data and kinetic solvent isotope effects, provide the experimental evidence for the SN2-SN3 spectrum (e.g., for chloro- and fluoroformates, chloroacetyl chloride, p-nitrobenzoyl p-toluenesulfonate, sulfonyl chlorides). Deviations from linearity lead to U- or V-shaped plots, which assist in the identification of the point at which the reaction channel changes from SN2-SN3 to SN1-SN2 (e.g., for benzoyl chloride). PMID:26006228

Calculated third order rate constants for interpreting the mechanisms of hydrolyses of chloroformates, carboxylic Acid halides, sulfonyl chlorides and phosphorochloridates.

PubMed

Bentley, T William

2015-05-08

Hydrolyses of acid derivatives (e.g., carboxylic acid chlorides and fluorides, fluoro- and chloroformates, sulfonyl chlorides, phosphorochloridates, anhydrides) exhibit pseudo-first order kinetics. Reaction mechanisms vary from those involving a cationic intermediate (SN1) to concerted SN2 processes, and further to third order reactions, in which one solvent molecule acts as the attacking nucleophile and a second molecule acts as a general base catalyst. A unified framework is discussed, in which there are two reaction channels-an SN1-SN2 spectrum and an SN2-SN3 spectrum. Third order rate constants (k3) are calculated for solvolytic reactions in a wide range of compositions of acetone-water mixtures, and are shown to be either approximately constant or correlated with the Grunwald-Winstein Y parameter. These data and kinetic solvent isotope effects, provide the experimental evidence for the SN2-SN3 spectrum (e.g., for chloro- and fluoroformates, chloroacetyl chloride, p-nitrobenzoyl p-toluenesulfonate, sulfonyl chlorides). Deviations from linearity lead to U- or V-shaped plots, which assist in the identification of the point at which the reaction channel changes from SN2-SN3 to SN1-SN2 (e.g., for benzoyl chloride).

Identification of a Pathway for Perfluorocompounds to Human Diet from Application of Biosolids to Agricultural Fields

EPA Science Inventory

Perfluoro compounds are ubiquitous contaminants in human blood. The pathways which result in near universal exposure to humans in modern societies are not clearly understood. Sources to environmental compartments and transport between compartments are only poorly studies, and thi...

Corrosion of stainless steel battery components by bis(fluorosulfonyl)imide based ionic liquid electrolytes

NASA Astrophysics Data System (ADS)

Evans, Tyler; Olson, Jarred; Bhat, Vinay; Lee, Se-Hee

2014-12-01

While the anodic behavior of aluminum foil current collectors in imide-based room temperature ionic liquids (RTILs) is relatively well understood, interactions between such RTILs and other passive battery components have not been studied extensively. This study presents the solvent and potential dependent oxidation of SS316 coin-cell components in the N-methyl-N-propyl-pyrrolidinium bis(fluorosulfonyl)imide (PYR13FSI) RTIL. While this phenomenon prohibits high-voltage cycling of Li(Ni1/3Mn1/3Co1/3)O2 cathodes in SS316 coin-type cells, Al-clad cell components or alternative cell configurations can be utilized to avoid SS316 oxidation-induced cell failure.

21 CFR 177.2450 - Polyamide-imide resins.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Determination as set forth in the “Official Methods of Analysis of the Association of Official Analytical... chromatography method titled “Amide-Imide Polymer Analysis—Analysis of Monomer Content,” is incorporated by... of films of 1 mil uniform thickness after coating and heat curing at 600 °F for 15 minutes on...

Immunomodulatory drugs in multiple myeloma: mechanisms of action and clinical experience

PubMed Central

Holstein, Sarah A.; McCarthy, Philip L.

2017-01-01

Over the last two decades, the outcomes for patients with multiple myeloma, a plasma cell malignancy, have dramatically improved. The development of the immunomodulatory drugs (IMiDs) which include thalidomide, lenalidomide, and pomalidomide, has contributed significantly to these improved outcomes. While thalidomide is now less commonly prescribed, lenalidomide is widely used in the treatment of newly diagnosed transplant-eligible and transplant-ineligible patients, in the maintenance setting post-transplant and in the relapsed/refractory setting, while pomalidomide is currently utilized in the relapsed/refractory setting. The IMiDs have been reported to have a multitude of activities, including anti-angiogenic, cytotoxic, and immunomodulatory, however, the more recent discoveries that the IMiDs bind to cereblon and thus regulate the ubiquitination of key transcription factors including IKZF1 and IKZF3, have provided greater insight into their mechanism of action. Here the clinical efficacy of these agents in myeloma is reviewed as well as discussion of structure-function relationship, the molecular mechanisms of action, and the association of IMiDs with second primary malignancies and thrombosis. PMID:28205024

Structure of the DDB1-CRBN E3 ubiquitin ligase in complex with thalidomide

PubMed Central

Fischer, Eric S.; Böhm, Kerstin; Lydeard, John R.; Yang, Haidi; Stadler, Michael B.; Cavadini, Simone; Nagel, Jane; Serluca, Fabrizio; Acker, Vincent; Lingaraju, Gondichatnahalli M.; Tichkule, Ritesh B.; Schebesta, Michael; Forrester, William C.; Schirle, Markus; Hassiepen, Ulrich; Ottl, Johannes; Hild, Marc; Beckwith, Rohan E. J.; Harper, J. Wade; Jenkins, Jeremy L.; Thomä, Nicolas H.

2015-01-01

In the 1950s the drug thalidomide administered as a sedative to pregnant women led to the birth of thousands of children with multiple defects. Despite its teratogenicity, thalidomide and its derivatives lenalidomide and pomalidomide (together known as Immunomodulatory Drugs: IMiDs) recently emerged as effective treatments for multiple myeloma and 5q-dysplasia. IMiDs target the CUL4-RBX1-DDB1-CRBN (CRL4CRBN) E3 ubiquitin ligase and promote the ubiquitination of Ikaros/Aiolos transcription factors by CRL4CRBN. Here we present the crystal structure of the DDB1-CRBN complex bound to thalidomide, lenalidomide and pomalidomide. The structure establishes CRBN as a CRL4CRBN substrate receptor, which enantioselectively binds IMiDs. Through an unbiased screen we identify the homeobox transcription factor MEIS2 as an endogenous substrate of CRL4CRBN. Our studies suggest that IMiDs block endogenous substrates (MEIS2) from binding to CRL4CRBN when recruiting Ikaros/Aiolos for degradation. This dual activity implies that small molecules can principally modulate a ligase to up- or down-regulate the ubiquitination of proteins. PMID:25043012

Imide Oligomers Containing Pendent and Terminal Phenylethynyl Groups-2

NASA Technical Reports Server (NTRS)

Connell, J. W.; Smith, J. G., Jr.; Hergenrother, P. M.

1998-01-01

As part of a program to develop high-performance/high-temperature structural resins for aeronautical applications, imide oligomers containing pendent and terminal phenylethynyl groups were prepared, characterized and the cured resins evaluated as composite matrices. The oligomers were prepared at a calculated number-average molecular weight of 5000 g/mol and contained 15-20 mol% pendent phenylethynyl groups. In previous work, an oligomer containing pendent and terminal phenylethynyl groups exhibited a high glass transition temperature (approximately 313 C), and laminates therefrom exhibited high compressive properties, but processability, fracture toughness, microcrack resistance and damage tolerance were less than desired. In an attempt to improve these deficiencies, modifications in the oligomeric backbone involving the incorporation of 1,3-bis(3-aminophenoxy)benzene were investigated as a means of improving processability and toughness without detracting from the high glass transition temperature and high compressive properties. The amide acid oligomeric solutions were prepared in N-methyl-2-pyrrolidinone and were subsequently processed into imide powder, thin films, adhesive tape and carbon fiber prepreg. Neat resin plaques were fabricated from imide powder by compression moulding. The maximum processing pressure was 1.4 MPa and the cure temperature ranged from 350 to 371 C for 1 h for the mouldings, adhesives, films and composites. The properties of the 1,3-bis(3-aniinophenoxy)benzene modified cured imide oligomers containing pendent and terminal phenylethynyl groups are compared with those of previously prepared oligomers containing pendent and terminal phenylethynyl groups of similar composition and molecular weight.

PERFLUOROPHOSPHONIC ACID ACTIVATES PEROXISOME PROUFERATOR-ACTIVATED RECEPTOR-ALPHA BUT NOT CONSTITUTIVE ANDROSTANE RECEPTOR IN THE MURINE LIVER

EPA Science Inventory

Masurf FS-780 is a commercial perfluoro-chemical mixture that contains C612-perfluoroalkylphosphonic acid (PFPA) derivatives. PFPAs have received recent attention as a previously under recognized subclass of perfluoroalkyl acids (PFAAs) that are found in the environment. The curr...

Thermally Induced Silane Dehydrocoupling on Silicon Nanostructures (International ed.)

DTIC Science & Technology

2016-07-29

grafted. When performed on a mesopo- rous Si wafer, the perfluoro reagent yields a superhydrophobic surface (contact angle 1518). The bromo-derivative... superhydrophobic behavior, with a water contact angle of 1508 (Figure S13 and S14). As with the octadecylsilane derivative, these surface chemistries were not

2-Diazo-1-phenyl-2-((trifluoromethyl)sulfonyl)ethan-1-one: Another Utility for Electrophilic Trifluoromethylthiolation Reactions.

PubMed

Huang, Zhongyan; Okuyama, Kenta; Wang, Chen; Tokunaga, Etsuko; Li, Xiaorui; Shibata, Norio

2016-06-01

2-Diazo-1-phenyl-2-((trifluoromethyl)sulfonyl)ethan-1-one (diazo-triflone) ( 2 ) is not only a building block but also a reagent. In this study, diazo-triflone, which was originally used for the synthesis of β-lactam triflones as a trifluoromethanesulfonyl (SO 2 CF 3 ) building block under catalyst-free thermal conditions, is redisclosed as an effective electrophilic trifluoromethylthiolation reagent under copper catalysis. A broad set of enamines, indoles, β-keto esters, pyrroles, and anilines were nicely transformed into corresponding trifluoromethylthio (SCF 3 ) compounds in good to high yields by diazo-triflone under copper catalysis via an electrophilic-type reaction. A coupling-type trifluoromethylthiolation reaction of aryl iodides was also realized by diazo-triflone in acceptable yields.

Preparation of pyrrolizinone derivatives via sequential transformations of cyclic allyl imides: synthesis of quinolactacide and marinamide.

PubMed

Simic, Milena; Tasic, Gordana; Jovanovic, Predrag; Petkovic, Milos; Savic, Vladimir

2018-03-28

A facile synthetic route has been developed for the preparation of pyrrolizinone derivatives employing N-allyl imides as starting materials. The nucleophilic addition of a vinyl Grignard reagent/RCM/elimination sequence afforded pyrrolizinones in good yields and has been applied for the preparation of naturally occurring quinolactacide and marinamide.

Electrochromic Salts, Solutions, and Devices

DOEpatents

Burrell, Anthony K.; Warner, Benjamin P.; McClesky, T. Mark

2008-11-11

Electrochromic salts. Electrochromic salts of dicationic viologens such as methyl viologen and benzyl viologen associated with anions selected from bis(trifluoromethylsulfonyl)imide, bis(perfluoroethylsulfonyl)imide, and tris(trifluoromethylsulfonyl)methide are produced by metathesis with the corresponding viologen dihalide. They are highly soluble in molten quarternary ammonium salts and together with a suitable reductant provide electrolyte solutions that are used in electrochromic windows.

Electrochromic salts, solutions, and devices

DOEpatents

Burrell, Anthony K [Los Alamos, NM; Warner, Benjamin P [Los Alamos, NM; McClesky,7,064,212 T. Mark

2006-06-20

Electrochromic salts. Electrochromic salts of dicationic viologens such as methyl viologen and benzyl viologen associated with anions selected from bis(trifluoromethylsulfonyl)imide, bis(perfluoroethylsulfonyl)imide, and tris(trifluoromethylsulfonyl)methide are produced by metathesis with the corresponding viologen dihalide. They are highly soluble in molten quarternary ammonium salts and together with a suitable reductant provide electrolyte solutions that are used in electrochromic windows.

Electrochromic Salts, Solutions, and Devices

DOEpatents

Burrell, Anthony K.; Warner, Benjamin P.; McClesky, T. Mark

2008-10-14

Electrochromic salts. Electrochromic salts of dicationic viologens such as methyl viologen and benzyl viologen associated with anions selected from bis(trifluoromethylsulfonyl)imide, bis(perfluoroethylsulfonyl)imide, and tris(trifluoromethylsulfonyl)methide are produced by metathesis with the corresponding viologen dihalide. They are highly soluble in molten quarternary ammonium salts and together with a suitable reductant provide electrolyte solutions that are used in electrochromic windows.

Gold-catalyzed synthesis of benzil derivatives and α-keto imides via oxidation of alkynes.

PubMed

Xu, Cheng-Fu; Xu, Mei; Jia, Yi-Xia; Li, Chuan-Ying

2011-03-18

An efficient process based on the gold-catalyzed redox reaction has been developed to oxidize 1,2-diarylacetylene or ynamide to 1,2-diaryldiketone or α-keto imide respectively. This process can tolerate a variety of functional groups and affords 1,2-dicarbonyl compounds in excellent yields under mild reaction conditions.

Chiral imidate-ferrocenylphosphanes: synthesis and application as P,N-ligands in iridium(I)-catalyzed hydrogenation of unfunctionalized and poorly functionalized olefins.

PubMed

Bert, Katrien; Noël, Timothy; Kimpe, Wim; Goeman, Jan L; Van der Eycken, Johan

2012-11-14

A small library of chiral imidate-ferrocenylphosphane ligands was efficiently synthesized (8 examples) and evaluated in the iridium(I)-catalyzed hydrogenation of unfunctionalized and poorly functionalized olefins. These catalysts perform very well in a range of examples (yields and ee's up to 100%).

Lithium insertion in graphite from ternary ionic liquid-lithium salt electrolytes. I. Electrochemical characterization of the electrolytes

NASA Astrophysics Data System (ADS)

Appetecchi, Giovanni B.; Montanino, Maria; Balducci, Andrea; Lux, Simon F.; Winterb, Martin; Passerini, Stefano

In this paper we report the results of chemical-physical investigation performed on ternary room temperature ionic liquid-lithium salt mixtures as electrolytes for lithium-ion battery systems. The ternary electrolytes were made by mixing N-methyl- N-propyl pyrrolidinium bis(fluorosulfonyl) imide (PYR 13FSI) and N-butyl- N-methylpyrrolidinium bis(trifluoromethanesulfonyl) imide (PYR 14TFSI) ionic liquids with lithium hexafluorophosphate (LiPF 6) or lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The mixtures were developed based on preliminary results on the cyclability of graphite electrodes in the IL-LiX binary electrolytes. The results clearly show the beneficial synergic effect of the two ionic liquids on the electrochemical properties of the mixtures.

Demonstrating hydrogen production from ammonia using lithium imide - Powering a small proton exchange membrane fuel cell

NASA Astrophysics Data System (ADS)

Hunter, Hazel M. A.; Makepeace, Joshua W.; Wood, Thomas J.; Mylius, O. Simon; Kibble, Mark G.; Nutter, Jamie B.; Jones, Martin O.; David, William I. F.

2016-10-01

Accessing the intrinsic hydrogen content within ammonia, NH3, has the potential to play a very significant role in the future of a CO2-free sustainable energy supply. Inexpensive light metal imides and amides are effective at decomposing ammonia to hydrogen and nitrogen (2NH3 → 3H2 + N2), at modest temperatures, and thus represent a low-cost approach to on-demand hydrogen production. Building upon this discovery, this paper describes the integration of an ammonia cracking unit with a post-reactor gas purification system and a small-scale PEM fuel cell to create a first bench-top demonstrator for the production of hydrogen using light metal imides.

40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

Code of Federal Regulations, 2011 CFR

2011-07-01

... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

Code of Federal Regulations, 2012 CFR

2012-07-01

... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

Code of Federal Regulations, 2014 CFR

2014-07-01

... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

Code of Federal Regulations, 2013 CFR

2013-07-01

... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

Use of a polar ionic liquid as second column for the comprehensive two-dimensional GC separation of PCBs.

PubMed

Zapadlo, Michal; Krupcík, Ján; Májek, Pavel; Armstrong, Daniel W; Sandra, Pat

2010-09-10

The orthogonality of three columns coupled in two series was studied for the congener specific comprehensive two-dimensional GC separation of polychlorinated biphenyls (PCBs). A non-polar capillary column coated with poly(5%-phenyl-95%-methyl)siloxane was used as the first ((1)D) column in both series. A polar capillary column coated with 70% cyanopropyl-polysilphenylene-siloxane or a capillary column coated with the ionic liquid 1,12-di(tripropylphosphonium)dodecane bis(trifluoromethane-sulfonyl)imide were used as the second ((2)D) columns. Nine multi-congener standard PCB solutions containing subsets of all native 209 PCBs, a mixture of 209 PCBs as well as Aroclor 1242 and 1260 formulations were used to study the orthogonality of both column series. Retention times of the corresponding PCB congeners on (1)D and (2)D columns were used to construct retention time dependences (apex plots) for assessing orthogonality of both columns coupled in series. For a visual assessment of the peak density of PCBs congeners on a retention plane, 2D images were compared. The degree of orthogonality of both column series was, along the visual assessment of distribution of PCBs on the retention plane, evaluated also by Pearson's correlation coefficient, which was found by correlation of retention times t(R,i,2D) and t(R,i,1D) of corresponding PCB congeners on both column series. It was demonstrated that the apolar+ionic liquid column series is almost orthogonal both for the 2D separation of PCBs present in Aroclor 1242 and 1260 formulations as well as for the separation of all of 209 PCBs. All toxic, dioxin-like PCBs, with the exception of PCB 118 that overlaps with PCB 106, were resolved by the apolar/ionic liquid series while on the apolar/polar column series three toxic PCBs overlapped (105+127, 81+148 and 118+106). Copyright 2010 Elsevier B.V. All rights reserved.

Deep eutectic solvents based on N-methylacetamide and a lithium salt as suitable electrolytes for lithium-ion batteries.

PubMed

Boisset, Aurélien; Menne, Sebastian; Jacquemin, Johan; Balducci, Andrea; Anouti, Mérièm

2013-12-14

In this work, we present a study on the physical and electrochemical properties of three new Deep Eutectic Solvents (DESs) based on N-methylacetamide (MAc) and a lithium salt (LiX, with X = bis[(trifluoromethyl)sulfonyl]imide, TFSI; hexafluorophosphate, PF6; or nitrate, NO3). Based on DSC measurements, it appears that these systems are liquid at room temperature for a lithium salt mole fraction ranging from 0.10 to 0.35. The temperature dependences of the ionic conductivity and the viscosity of these DESs are correctly described by using the Vogel-Tammann-Fulcher (VTF) type fitting equation, due to the strong interactions between Li(+), X(-) and MAc in solution. Furthermore, these electrolytes possess quite large electrochemical stability windows up to 4.7-5 V on Pt, and demonstrate also a passivating behavior toward the aluminum collector at room temperature. Based on these interesting electrochemical properties, these selected DESs can be classified as potential and promising electrolytes for lithium-ion batteries (LIBs). For this purpose, a test cell was then constructed and tested at 25 °C, 60 °C and 80 °C by using each selected DES as an electrolyte and LiFePO4 (LFP) material as a cathode. The results show a good compatibility between each DES and LFP electrode material. A capacity of up to 160 mA h g(-1) with a good efficiency (99%) is observed in the DES based on the LiNO3 salt at 60 °C despite the presence of residual water in the electrolyte. Finally preliminary tests using a LFP/DES/LTO (lithium titanate) full cell at room temperature clearly show that LiTFSI-based DES can be successfully introduced into LIBs. Considering the beneficial properties, especially, the cost of these electrolytes, such introduction could represent an important contribution for the realization of safer and environmentally friendly LIBs.

Crosslinked structurally-tuned polymeric ionic liquids as stationary phases for the analysis of hydrocarbons in kerosene and diesel fuels by comprehensive two-dimensional gas chromatography.

PubMed

Zhang, Cheng; Park, Rodney A; Anderson, Jared L

2016-04-01

Structurally-tuned ionic liquids (ILs) have been previously applied as the second dimension column in comprehensive two-dimensional gas chromatography (GC×GC) and have demonstrated high selectivity in the separation of individual aliphatic hydrocarbons from other aliphatic hydrocarbons. However, the maximum operating temperatures of these stationary phases limit the separation of analytes with high boiling points. In order to address this issue, a series of polymeric ionic liquid (PIL)-based stationary phases were prepared in this study using imidazolium-based IL monomers via in-column free radical polymerization. The IL monomers were functionalized with long alkyl chain substituents to provide the needed selectivity for the separation of aliphatic hydrocarbons. Columns were prepared with different film thicknesses to identify the best performing stationary phase for the separation of kerosene. The bis[(trifluoromethyl)sulfonyl]imide ([NTf2](-))-based PIL stationary phase with larger film thickness (0.28μm) exhibited higher selectivity for aliphatic hydrocarbons and showed a maximum allowable operating temperature of 300°C. PIL-based stationary phases containing varied amount of IL-based crosslinker were prepared to study the effect of the crosslinker on the selectivity and thermal stability of the resulting stationary phase. The optimal resolution of aliphatic hydrocarbons was achieved when 50% (w/w) of crosslinker was incorporated into the PIL-based stationary phase. The resulting stationary phase exhibited good selectivity for different groups of aliphatic hydrocarbons even after being conditioned at 325°C. Finally, the crosslinked PIL-based stationary phase was compared with SUPELCOWAX 10 and DB-17 columns for the separation of aliphatic hydrocarbons in diesel fuel. Better resolution of aliphatic hydrocarbons was obtained when employing the crosslinked PIL-based stationary phase as the second dimension column. Copyright © 2016 Elsevier B.V. All rights reserved.

Conductivity and spectroscopic investigation of bis(trifluoromethanesulfonyl)imide solution in ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide.

PubMed

Yu, Lei; Pizio, Benjamin S; Vaden, Timothy D

2012-06-07

Protic ionic liquids (PILs) are promising alternatives to water for swelling Nafion as a fuel cell proton exchange membrane (PEM). PILs can significantly improve the high-temperature performance of a PEM. The proton dissociation and solvation mechanisms in a PIL, which are keys to understanding the proton transportation and conductivity, have not been fully explored. In this paper, we used FTIR, Raman, and electronic spectroscopy with computational simulation techniques to explore the spectroscopic properties of bis(trifluoromethanesulfonyl)imide (HTFSI) solutions in 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (BMITFSI) ionic liquid at concentrations from ∼0.1 to as high as ∼1.0 M. Solution conductivities were measured at room temperature and elevated temperatures up to ∼65 °C. The solution structure and properties depend on the concentration of HTFSI. At lower concentration, around 0.1 M, the HTFSI solution has higher conductivity than pure BMITFSI. However, the conductivity decreases when the concentration increases from 0.1 to 1.0 M. Temperature-dependent conductivities followed the Vogel-Fulcher-Tamman equation at all concentrations. Conductivity and spectroscopy results elucidate the complicated ionization and solvation mechanism of HTFSI in BMITFSI solutions. Raman spectroscopy and density functional theory (DFT) calculations are consistent with the complete ionization of HTFSI to generate solvated H(+) at low concentrations. FTIR, Raman, and electronic spectroscopic results as well as DFT computational simulation indicated that when the concentration is as high as 1.0 M, a significant amount of TFSI(-) is protonated, most likely at the imide nitrogen.

Preparation of a Highly Fluorophilic Phosphonium Salt and its Use in a Fluorous Anion-Exchanger Membrane with High Selectivity for Perfluorinated Acids

PubMed Central

Boswell, Paul G.; Anfang, Alyce C.; Bühlmann, Philippe

2008-01-01

Fluorous solvents are the most nonpolar, nonpolarizable phases known, whereas ions are inherently polar. This makes it difficult to create salts that are soluble in a fluorous solvent. Here we present the synthesis and characterization of a new fluorophilic phosphonium salt, tris{3,5-bis[(perfluorooctyl)propyl]phenyl}methylphosphonium methyl sulfate. The salt has a solubility of at least 14 mM in perfluoro(perhydrophenanthrene), perfluoro(methylcyclohexane), and perfluorohexanes. It also shows immediate potential for use as a phase-transfer catalyst in fluorous biphasic catalysis, but in this work it is used as an anion exchanger site in the first potentiometric fluorous-membrane anion-selective electrode. The membrane sensor exhibited the exceptional selectivity of 3.9 × 1010 to 1 for perfluorooctanesulfonate over chloride, and of 2.5 × 107 to 1 for perfluorooctanoate over chloride. With improvements to the sensor’s detection limit and lifetime, it has the potential to be an attractive alternative to the expensive, time-consuming methods currently employed for measurement of perfluorinated acids. PMID:22072222

Design and chemical synthesis of iodine-containing molecules for application to solar-pumped I* lasers

NASA Technical Reports Server (NTRS)

Shiner, C. S.

1986-01-01

The design and chemical synthesis of new media for solar pumped iodine molecule lasers are explored. In an effort to prepare an iodo fluorocarbon compound absorbing strongly at 300 nm or above, the synthesis of perfluoro allylic iodides was investigated. These compounds furnish especially stable allylic radicals upon photodissociation. The desired red shift is anticipated in the absorption maximum could correlate with increasing radical stability. This expectation was based upon the analysis, previously reported, of the structures and absorption maxima of compounds studied earlier. A previously unknown substance was prepared, a prototypical target molecule, perfluoro-3-iodocyclopent-1-ene. It was obtained by reaction of perfluorocyclopentene with sulfur trioxide under the influence of antimony pentafluoride catalyst, followed by treatment of the resulting allylic fluorosulfonate with sodium iodide in sulfoland solvent. Preliminary data indicate that the absorption maximum for the iodo fluorocarbon is not shifted significantly to longer wavelength. It is not certain whether this result reflects an unexpected influence of the cyclic structure upon the position of the absorption maximum.

Anaerobic biodegradability and methanogenic toxicity of key constituents in copper chemical mechanical planarization effluents of the semiconductor industry.

PubMed

Hollingsworth, Jeremy; Sierra-Alvarez, Reyes; Zhou, Michael; Ogden, Kimberly L; Field, Jim A

2005-06-01

Copper chemical mechanical planarization (CMP) effluents can account for 30-40% of the water discharge in semiconductor manufacturing. CMP effluents contain high concentrations of soluble copper and a complex mixture of organic constituents. The aim of this study is to perform a preliminary assessment of the treatability of CMP effluents in anaerobic sulfidogenic bioreactors inoculated with anaerobic granular sludge by testing individual compounds expected in the CMP effluents. Of all the compounds tested (copper (II), benzotriazoles, polyethylene glycol (M(n) 300), polyethylene glycol (M(n) 860) monooleate, perfluoro-1-octane sulfonate, citric acid, oxalic acid and isopropanol) only copper was found to be inhibitory to methanogenic activity at the concentrations tested. Most of the organic compounds tested were biodegradable with the exception of perfluoro-1-octane sulfonate and benzotriazoles under sulfate reducing conditions and with the exception of the same compounds as well as Triton X-100 under methanogenic conditions. The susceptibility of key components in CMP effluents to anaerobic biodegradation combined with their low microbial inhibition suggest that CMP effluents should be amenable to biological treatment in sulfate reducing bioreactors.

Cycling and rate performance of Li-LiFePO 4 cells in mixed FSI-TFSI room temperature ionic liquids

NASA Astrophysics Data System (ADS)

Lewandowski, A. P.; Hollenkamp, A. F.; Donne, S. W.; Best, A. S.

A study is conducted of the performance of lithium iron(II) phosphate, LiFePO 4, as a cathode material in a lithium secondary battery that features an ionic liquid electrolyte solution and a metallic lithium anode. The electrolyte solution comprises an ionic liquid of a N-methyl-N-alkyl-pyrrolidinium (alkyl = n-propyl or n-butyl) cation and either the bis(fluorosulfonyl)imide [(FSO 2) 2N -] or bis(trifluoromethanesulfonyl)imide [(F 3CSO 2) 2N -] anion, together with 0.5 mol kg -1 of lithium bis(trifluoromethanesulfonyl)imide salt. For N-methyl-N-propyl-pyrrolidinium bis(fluorosulfonyl)imide, coin cells discharging at rates of C/10 and 4C yield specific capacities of 153 and 110 mAh g -1, respectively, at an average coulombic efficiency of 99.8%. This performance is maintained for over 400 cycles at 50 °C and therefore indicates that these electrolyte solutions support long-term cycling of both LiFePO 4 and metallic lithium while, due to the negligible volatility of ionic liquids, surrounding the lithium in an inherently safe, non-flammable medium.

Molecular dynamics simulations of trans- and cis- N-acetyl- N'-methylamides of XaaPro dipeptides

NASA Astrophysics Data System (ADS)

Hoon Choi, Seung; Yun Yu, Jeong; Kwang Shin, Jae; Shik Jhon, Mu

1994-07-01

The occurrence of cis imide bonds in proteins is much higher than that of cis amide bonds due to the unique properties of proline. In order to examine the relationship between the high occurrence of these cis imide bonds and the residues preceding the proline, we perform molecular dynamics simulations of trans- and cis- N-acetyl- N'-methylamides of XaaPro dipeptides (AcXaaProNHMe). We investigate the conformational energies and structures of trans- and cis-AcXaa where Xaa has 12 amino acids in the vacuum state and 5 amino acids in the solution state. It is found that the occurrence of the cis imide bonds is strongly affected by the residue preceding the proline, and the dihedral angles (φ,ψ) of the backbone in AcXaaProNHMe are influenced by the configuration of the imide bond. We also find that the equilibrium properties of XaaPro in solution simulations are more similar to the statistics of X-ray crystallographic data than are those in vacuum simulations and solvation causes a remarkable change in the conformation of the pyrrolidine ring from the endo to the exo form.

N-15 NMR Spectroscopy as a Method for Comparing the Rates of Imidization of Several Diamines

NASA Technical Reports Server (NTRS)

Johnson, J. Christopher; Kuczmarski, Maria A.

2006-01-01

The relative rates of the conversion of amide-acid to imide was measured for a series or aromatic diamines that have been identified as potential replacements for 4,4'-methylene dianiline (MDA) in high-temperature polyimides and polymer composites. These rates were compared with the N-15 NMR resonances of the unreacted amines. The initial rates of imidization track with the difference in chemical shift between the amine nitrogens in MDA and those in the subject diamines. This comparison demonstrated that N-15 NMR spectroscopy is appropriate for the rapid screening of candidate diamines to determine their reactivity relative to MDA, and can serve to provide guidance to the process of creating the time-temperature profiles used in processing these materials into polymer matrix composites.

Effect of integrated infectious disease training and on-site support on the management of childhood illnesses in Uganda: a cluster randomized trial.

PubMed

Imani, Peace; Jakech, Brian; Kirunda, Ibrahim; Mbonye, Martin K; Naikoba, Sarah; Weaver, Marcia R

2015-08-28

The Integrated Infectious Disease Capacity-Building Evaluation (IDCAP) was designed to test the effects of two interventions, Integrated Management of Infectious Disease (IMID) training and on-site support (OSS), on clinical practice of mid-level practitioners. This article reports the effects of these interventions on clinical practice in management of common childhood illnesses. Two trainees from each of 36 health facilities participated in the IMID training. IMID was a three-week core course, two one-week boost courses, and distance learning over nine months. Eighteen of the 36 health facilities were then randomly assigned to arm A, and participated in OSS, while the other 18 health facilities assigned to arm B did not. Clinical faculty assessed trainee practice on clinical practice of six sets of tasks: patient history, physical examination, laboratory tests, diagnosis, treatment, and patient/caregiver education. The effects of IMID were measured by the post/pre adjusted relative risk (aRR) of appropriate practice in arm B. The incremental effects of OSS were measured by the adjusted ratio of relative risks (aRRR) in arm A compared to arm B. All hypotheses were tested at a 5% level of significance. Patient samples were comparable across arms at baseline and endline. The majority of children were aged under five years; 84% at baseline and 97% at endline. The effects of IMID on patient history (aRR = 1.12; 95% CI = 1.04-1.21) and physical examination (aRR = 1.40; 95% CI = 1.16-1.68) tasks were statistically significant. OSS was associated with incremental improvement in patient history (aRRR = 1.18; 95% CI = 1.06-1.31), and physical examination (aRRR = 1.27; 95% CI = 1.02-1.59) tasks. Improvements in laboratory testing, diagnosis, treatment, and patient/caregiver education were not statistically significant. IMID training was associated with improved patient history taking and physical examination, and OSS further improved these clinical practices. On-site training and continuous quality improvement activities support transfer of learning to practice among mid-level practitioners.

Development of [18F]DASA-23 for Imaging Tumor Glycolysis Through Noninvasive Measurement of Pyruvate Kinase M2.

PubMed

Beinat, Corinne; Alam, Israt S; James, Michelle L; Srinivasan, Ananth; Gambhir, Sanjiv Sam

2017-10-01

A hallmark of cancer is metabolic reprogramming, which is exploited by cancer cells to ensure rapid growth and survival. Pyruvate kinase M2 (PKM2) catalyzes the final step in glycolysis, a key step in tumor metabolism and growth. Recently, we reported the radiosynthesis of the first positron emission tomography tracer for visualizing PKM2 in vivo-i.e., [ 11 C]DASA-23. Due to the highly promising imaging results obtained with [ 11 C]DASA-23 in rodent model glioblastoma, we set out to generate an F-18-labeled version of this tracer, with the end goal of clinical translation in mind. Herein, we report the radiosynthesis of 1-((2-fluoro-6-[ 18 F]fluorophenyl)sulfonyl)-4-((4-methoxyphenyl)sulfonyl)piperazine ([ 18 F]DASA-23) and our initial investigation of its binding properties in cancer cells. We synthesized [ 18 F]DASA-23 via fluorination of 1-((2-fluoro-6-nitrophenyl)sulfonyl)-4-((4-methoxyphenyl)sulfonyl)piperazine (10) with K[ 18 F]F/K2.2.2 in N,N-dimethylformamide at 110 °C for 20 min. Subsequently, we evaluated uptake of [ 18 F]DASA-23 in HeLa cervical adenocarcinoma cells and in vitro stability in human and mouse serum. We successfully prepared [ 18 F]DASA-23 in 2.61 ± 1.54 % radiochemical yield (n = 10, non-decay corrected at end of synthesis) with a specific activity of 2.59 ± 0.44 Ci/μmol. Preliminary cell uptake experiments revealed high uptake in HeLa cells, which was effectively blocked by pretreating cells with the structurally distinct PKM2 activator, TEPP-46. [ 18 F]DASA-23 remained intact in human and mouse serum up to 120 min. Herein, we have identified a F-18-labeled PKM2 specific radiotracer which shows potential for in vivo imaging. The promising cell uptake results reported herein warrant the further evaluation of [ 18 F]DASA-23 for its ability to detect and monitor cancer noninvasively.

Biodegradation of sulfosulphuron in agricultural soil by Trichoderma sp.

PubMed

Yadav, U; Choudhury, P P

2014-11-01

Sulfosulphuron-degrading fungus was isolated by enrichment technique from the sulfosulphuron-contaminated soil of wheat rhizosphere. To assess the biodegradation potential of isolated Trichoderma sp., minimal potato dextrose agar broth with different levels of sulfosulphuron (up to 2 g l(-1) ) was evaluated in the growth and biotransformation experiments. ESI LC-MS/MS analysis revealed the presence of degradation products 2-amino-4,6-dimethoxypyrimidine (I) and 2-ethylsulfonyl imidazo{1,2-a} pyridine-3-sulfonamide-2-ethylsulfonyl imidazo{1,2-a} pyridine-3-sulfonamide (II) indicating the cleavage of the urea bridge and the presence of the by-product N-(4,6-dimethoxypyrimidin-2-yl)urea (III) indicating the degradation of sulfonylamide linkage. Two other metabolites, N-(4,6-dimethoxypyrimidin-2-yl)-N'-hydroxyurea (IV) and N, N'-bis(4,6-dimethoxypyrimidin-2-yl)urea (V), were also identified. From the previous reports, it was found that the degradation of sulfonyl urea herbicides took place through the chemical degradation of the sulfonylurea bridge followed by microbial degradation. During this investigation, Trichoderma sp. grew well with and degraded sulfosulphuron via both the decarboxylation on the sulphonyl urea bridge and the hydrolytic cleavage of the sulfonylamide linkage as demonstrated by the formation of metabolites. Trichoderma is nonphytopathogenic in nature, and some species of it restrict the growth of soil-dwelling phytopathogens. Therefore, it is a promising candidate for the decontamination of soil from sulfosulphuron residues. The degradation of sulfosulphuron by any individual fungus is being reported for the first time. Trichoderma sp. isolated from wheat-rhizospheric soil could survive in minimal broth rich in sulfosulphuron. Previous reports have described the complete degradation of any sulfonyl urea herbicides by micro-organisms only after the pH-dependent chemical hydrolysis of the sulfonyl urea bridge of the herbicide. This study demonstrates the novel result that the Trichoderma sp. utilized the sulfosulphuron as a sole carbon source and degraded it by cleaving sulfonyl urea bridge and sulfonylamide linkage. Thus, the application of Trichoderma sp., which is nonphytopathogenic, has the potential to decontaminate agricultural soil from sulfosulphuron load. © 2014 The Society for Applied Microbiology.

Anodic Behavior of the Aluminum Current Collector in Imide-Based Electrolytes: Influence of Solvent, Operating Temperature, and Native Oxide-Layer Thickness.

PubMed

Meister, Paul; Qi, Xin; Kloepsch, Richard; Krämer, Elisabeth; Streipert, Benjamin; Winter, Martin; Placke, Tobias

2017-02-22

The inability of imide salts to form a sufficiently effective passivation layer on aluminum current collectors is one of the main obstacles that limit their broad application in electrochemical energy-storage systems. However, under certain circumstances, the use of electrolytes with imide electrolyte salts in combination with the aluminum current collector is possible. In this contribution, the stability of the aluminum current collector in electrolytes containing either lithium bis(trifluoromethanesulfonyl) imide (LiTFSI) or lithium fluorosulfonyl-(trifluoromethanesulfonyl) imide (LiFTFSI) as conductive salt was investigated by electrochemical techniques, that is, cyclic voltammetry (CV) and chronocoulometry (CC) in either room-temperature ionic liquids or in ethyl methyl sulfone. In particular, the influence of the solvent, operating temperature, and thickness of the native oxide layer of aluminum on the pit formation at the aluminum current collector surface was studied by means of scanning electron microscopy. In general, a more pronounced aluminum dissolution and pit formation was found at elevated temperatures as well as in solvents with a high dielectric constant. An enhanced thickness of the native aluminum oxide layer increases the oxidative stability versus dissolution. Furthermore, we found a different reaction rate depending on dwell time at the upper cut-off potential for aluminum dissolution in TFSI- and FTFSI-based electrolytes during the CC measurements; the use of LiFTFSI facilitated the dissolution of aluminum compared to LiTFSI. Overall, the mechanism of anodic aluminum dissolution is based on: i) the attack of the Al 2 O 3 surface by acidic species and ii) the dissolution of bare aluminum into the electrolyte, which, in turn, is influenced by the electrolyte's dielectric constant. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Pomalidomide desensitization in a patient hypersensitive to immunomodulating agents

PubMed Central

Seki, J.T.; Sakurai, N.; Lam, W.; Reece, D.E.

2017-01-01

Despite progressive treatments with tandem stem-cell transplantation, patients with incurable myeloma eventually succumb to relapsed or refractory disease if left untreated. Promising agents such as proteasome inhibitors and immunomodulating imide drugs (imids), including the newer-generation agent pomalidomide, in combination with lower-dose dexamethasone, have been shown to be effective and to significantly improve and prolong survival in pretreated patients. Although the incidence of pomalidomide hypersensitivity reaction (hsr) in this class of drugs is not as well known, we have documented cutaneous toxicity (grade 3 by the Common Terminology Criteria for Adverse Events, version 4) in 2 separate cases (not yet published). Because the imids are chemically, structurally, and pharmacologically similar, it is not unreasonable to consider possible cross-reactivity in pomalidomide recipients who developed hsr when receiving previous lines of imids. As a patient’s advocate, it is only prudent to provide a responsible, and yet practical, means to better address cross-sensitivity for patients. Intervention with the use of a rapid desensitization program (rdp) as a preventive measure should be introduced before initiating pomalidomide. Such a proactive measure for the patient’s safety will ensure a smooth transition into pomalidomide treatment. A hsr can be either related or non-related to immunoglobulin E. As imids become an essential treatment backbone for myeloma and other plasma-cell diseases, an increasing number of patients could experience skin and other life-threatening toxicities, resulting in unnecessary discontinuation of these life-prolonging agents. An extemporaneously prepared pomalidomide suspension developed at our centre enables patients to undergo rdp safely. Patients enjoy a good quality of life and clinical response after the rdp procedure. PMID:28874903

Cost-effectiveness of an influenza vaccination program offering intramuscular and intradermal vaccines versus intramuscular vaccine alone for elderly.

PubMed

Leung, Man-Kit; You, Joyce H S

2016-05-11

Intradermal (ID) injection is an alternative route for influenza vaccine administration in elderly with potential improvement of vaccine coverage. This study aimed to investigate the cost-effectiveness of an influenza vaccination program offering ID vaccine to elderly who had declined intramuscular (IM) vaccine from the perspective of Hong Kong public healthcare provider. A decision analytic model was used to simulate outcomes of two programs: IM vaccine alone (IM program), and IM or ID vaccine (IM/ID program) in a hypothetic cohort of elderly aged 65 years. Outcome measures included influenza-related direct medical cost, infection rate, mortality rate, quality-adjusted life years (QALYs) loss, and incremental cost per QALY saved (ICER). Model inputs were derived from literature. Sensitivity analyses evaluated the impact of uncertainty of model variables. In base-case analysis, the IM/ID program was more costly (USD52.82 versus USD47.59 per individual to whom vaccine was offered) with lower influenza infection rate (8.71% versus 9.65%), mortality rate (0.021% versus 0.024%) and QALYs loss (0.00336 versus 0.00372) than the IM program. ICER of IM/ID program was USD14,528 per QALY saved. One-way sensitivity analysis found ICER of IM/ID program to exceed willingness-to-pay threshold (USD39,933) when probability of influenza infection in unvaccinated elderly decreased from 10.6% to 5.4%. In 10,000 Monte Carlo simulations of elderly populations of Hong Kong, the IM/ID program was the preferred option in 94.7% of time. An influenza vaccination program offering ID vaccine to elderly who had declined IM vaccine appears to be a highly cost-effective option. Copyright © 2016 Elsevier Ltd. All rights reserved.

Synthesis and Characterization of Perfluoroalkyl Heterocyclic Elastomers

DTIC Science & Technology

Perfluoroalkyl bibenzoxazole polymers containing a (CF2)8 between heterocyclic rings have been prepared by the reaction of dihydroxybenzidine and...methyl perfluorosebacimidate . Through preparation of this polymer, the basic polymerization system has been significantly improved and polymers with...C. (TGA). Copolymers of dihydroxybenzidine and methyl perfluoro -4,9,14,19- tetraoxadocosanediimidate, which are tacky and resilient, have been

Oxygen plasma resistant phosphine oxide containing imide/arylene copolymers

NASA Technical Reports Server (NTRS)

Jensen, Brian J.

1993-01-01

A series of oxygen plasma resistant imide/arylene ether copolymers were prepared by reacting anhydride-terminated poly(amide acids) and amine-terminated polyarylene ethers containing phosphine oxide units. Inherent viscosities for these copolymers ranged from 0.42 to 0.80 dL/g. After curing, the resulting copolymers had glass transition temperatures ranging from 224 C to 228 C. Solution cast films of the block copolymers were tough and flexible with tensile strength, tensile moduli, and elongation at break up to 16.1 ksi, 439 ksi, and 23 percent, respectively at 25 C and 9.1 ksi, 308 ksi and 97 percent, respectively at 150 C. The copolymers show a significant improvement in resistance to oxygen plasma when compared to the commercial polyimide Kapton. The imide/arylene ether copolymers containing phosphine oxide units are suitable as coatings, films, adhesives, and composite matrices.

Lithium insertion in graphite from ternary ionic liquid-lithium salt electrolytes: II. Evaluation of specific capacity and cycling efficiency and stability at room temperature

NASA Astrophysics Data System (ADS)

Lux, Simon F.; Schmuck, Martin; Appetecchi, Giovanni B.; Passerini, Stefano; Winter, Martin; Balducci, Andrea

In this paper we report the results about the use of ternary room temperature ionic liquid-lithium salt mixtures as electrolytes for lithium-ion battery systems. Mixtures of N-methyl- N-propyl pyrrolidinium bis(fluorosulfonyl) imide, PYR 13FSI, and N-butyl- N-methylpyrrolidinium bis(trifluoromethansulfonyl) imide, PYR 14TFSI, with lithium hexafluorophosphate, LiPF 6 and lithium bis(trifluoromethansulfonyl) imide, LiTFSI, containing 5 wt.% of vinylene carbonate (VC) as additive, have been used in combination with a commercial graphite, KS6 TIMCAL. The performance of the graphite electrodes has been considered in term of specific capacity, cycling efficiency and cycling stability. The results clearly show the advantage of the use of ternary mixtures on the performance of the graphite electrode.

New Poly(amide-imide)/Nanocomposites Reinforced Silicate Nanoparticles Based on N-pyromellitimido-L-phenyl Alanine Containing Ether Moieties

NASA Astrophysics Data System (ADS)

Faghihi, Khalil; Shabanian, Meisam; Dadfar, Ehsan

2012-02-01

A series of Poly(amide-imide)/montmorillonite nanocomposites containing N-pyromellitimido-L-phenyl alanine moiety in the main chain were synthesized by a convenient solution intercalation technique. Poly(amide-imide) (PAI) 5 as a source of polymer matrix was synthesized by the direct polycondensation reaction of N-pyromellitimido-L-phenyl alanine 3 with 4,4'-diamino diphenyl ether 4 in the presence of triphenyl phosphite (TPP), CaCl2, pyridine and N-methyl-2-pyrrolidone (NMP). The resulting nanocomposite films were characterized by Fourier transform infrared spectra (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). The results showed that organo-modified clay was dispersed homogeneously in PAI matrix. TGA indicated an enhancement of thermal stability of new nanocomposites compared with the pure polymer.

Thermal and Optical Properties of New Poly(amide-imide)/Nanocomposite Reinforced by Layer Silicate Containing Diphenyl Ether Moieties

NASA Astrophysics Data System (ADS)

Faghihi, Khalil; Faramarzi, Ellahe; Shabanian, Meisam

2011-04-01

New poly(amide-imide)-montmorillonite reinforced nanocomposites containing Bis(4-N-trimellitylimido) diphenyl ether moiety in the main chain were synthesized by a convenient solution intercalation technique. Poly(amide-imide) (PAI) 4 was synthesized by the direct polycondensation reaction of Bis(4-N-trimellitylimido) diphenyl ether 3 with 4,4'-diamino diphenyl ether 2 in the presence of triphenyl phosphite (TPP), CaCl2, pyridine and N-methyl-2-pyrrolidone (NMP). Morphology and structure of the resulting PAI-nanocomposite films 4a and 4b with 10 and 20 mass% silicate particles respectively, were characterized by FT-IR spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The properties of nanocomposites films were investigated by using Uv-vis spectroscopy, thermogravimetric analysis (TGA) and water uptake measurements.

Imide/arylene ether copolymers

NASA Technical Reports Server (NTRS)

Jensen, Brian J. (Inventor); Hergenrother, Paul M. (Inventor); Bass, Robert G. (Inventor)

1992-01-01

Imide/arylene ether block copolymers are prepared by reacting anhydride terminated poly(amic acids) with amine terminated poly(arylene ethers) in polar aprotic solvents and by chemically or thermally cyclodehydrating the resulting intermediate poly(amic acids). The resulting block copolymers have one glass transition temperature or two, depending upon the particular structure and/or the compatibility of the block units. Most of these block copolymers form tough, solvent resistant films with high tensile properties.

Molecular structure of imide solutions. Part I. Propionimide in non-polar solvents

NASA Astrophysics Data System (ADS)

Jadżyn, J.; Żywucki, B.

1986-07-01

cis-trans Conformation of the imide group in propionimide (C 2H 5CONHCOC 2H 5) leads to its cyclic dimerization via the NH⋯OC hydrogen bonds. Dielectric and IR studies in non-polar solvents showed that the dipole moment of the propionimide cyclic dimer is equal to zero. The thermodynamic parameters describing the process of this dimerization are given.

Well-Known Mediators of Selective Oxidation with Unknown Electronic Structure: Metal-Free Generation and EPR Study of Imide-N-oxyl Radicals.

PubMed

Krylov, Igor B; Kompanets, Mykhailo O; Novikova, Katerina V; Opeida, Iosip O; Kushch, Olga V; Shelimov, Boris N; Nikishin, Gennady I; Levitsky, Dmitri O; Terent'ev, Alexander O

2016-01-14

Nitroxyl radicals are widely used in chemistry, materials sciences, and biology. Imide-N-oxyl radicals are subclass of unique nitroxyl radicals that proved to be useful catalysts and mediators of selective oxidation and CH-functionalization. An efficient metal-free method was developed for the generation of imide-N-oxyl radicals from N-hydroxyimides at room temperature by the reaction with (diacetoxyiodo)benzene. The method allows for the production of high concentrations of free radicals and provides high resolution of their EPR spectra exhibiting the superhyperfine structure from benzene ring protons distant from the radical center. An analysis of the spectra shows that, regardless of the electronic effects of the substituents in the benzene ring, the superhyperfine coupling constant of an unpaired electron with the distant protons at positions 4 and 5 of the aromatic system is substantially greater than that with the protons at positions 3 and 6 that are closer to the N-oxyl radical center. This is indicative of an unusual character of the spin density distribution of the unpaired electron in substituted phthalimide-N-oxyl radicals. Understanding of the nature of the electron density distribution in imide-N-oxyl radicals may be useful for the development of commercial mediators of oxidation based on N-hydroxyimides.

Adhesive Properties of Cured Phenylethynyl Containing Imides

NASA Technical Reports Server (NTRS)

Jensen, Brian J.; Chang, Alice C.

1997-01-01

Considerable attention has been directed towards acetylene terminated oligomers over the last 20 years' and recent work has focused on phenylethynyl terminated imide (PETI) oligomers. These reactive oligomers possess several features which make them attractive candidates for use as composite matrices and adhesives. The phenylethynyl group can be readily incorporated into many different functionalized oligomers. The reactive oligomers possess relatively low melt viscosities and thermally cure without the evolution of volatile by-products. Once cured, they typically display high glass transition temperatures (Tgs), excellent solvent resistance and high mechanical properties. new modified phenylethynyl-terminated imide (LaRC MPEI) oligomers were synthesized at various molecular weights utilizing a small amount of trifunctional amine. As long as the amount of triamine is relatively small, this approach produces a mixture of linear, star-shaped and branched polymer chains that has lower melt and solution viscosity than an equivalent molecular weight linear phenylethynyl terminated imide oligomers. The work reported herein involves the synthesis and characterization of a copolymer using this approach and the preparation of blends utilizing a phenylethynyl containing reactive plasticizer of lower molecular weight called LaRC LV-121. The chemistry and properties of this new MPEI as well as some blends of MPEI with LV-121, are presented and compared to the linear version, LARC-PETI-5.

Synthesis of Cyclopentenimines from N-Allyl Ynamides via a Tandem Aza-Claisen Rearrangement–Carbocyclization Sequence

PubMed Central

Wang, Xiao-Na; Winston-McPherson, Gabrielle N.; Walton, Mary C.; Zhang, Yu

2013-01-01

We describe here details of our investigations into Pd-catalyzed and thermal aza-Claisen–carbocyclizations of N-allyl ynamides to prepare a variety of α,β-unsaturated cyclopentenimines. The nature of the ynamide electron withdrawing group and β-substituent plays critical roles in the success of this tandem cascade. With N-sulfonyl ynamides, the use of palladium catalysis is required, as facile 1,3-sulfonyl shifts dominate under thermal conditions. However, since no analogous 1,3-phosphoryl shift is operational, N-phosphoryl ynamides could be used to prepare similar cyclopentenimines under thermal conditions through zwitter ionic intermediates that undergo N-promoted H-shifts. Alternatively, by employing ynamides bearing tethered carbon nucleophiles, the zwitter ionic intermediates could be intercepted giving rise rapidly to more complex fused bi- and tricyclic scaffolds. PMID:23718841

Solvent-dependent reactions for the synthesis of β-keto-benzo-δ-sultone scaffolds via DBU-catalyzed O-sulfonylation/intramolecular Baylis-Hillman/1,3-H shift or dehydration tandem sequences.

PubMed

Ghandi, Mehdi; Bozcheloei, Abolfazl Hasani; Nazari, Seyed Hadi; Sadeghzadeh, Masoud

2011-12-16

We have developed a solvent-dependent method for the synthesis of novel benzo-δ-sultone scaffolds. A variety of benzylbenzo[e][1,2]oxathiin-4(3H)-one-2,2-dioxides were obtained in high yields in DMF using a one-pot, DBU-catalyzed condensation of 2-hydroxybenzaldehydes with a number of (E)-2-phenylethenesulfonyl chlorides. On the other hand, the initially prepared 2-formylphenyl-(E)-2-phenylethenesulfonate derivatives underwent DBU-catalyzed reactions to a series of 3-[methoxy(phenyl)methyl]benzo[e][1,2]oxathiine-2,2-dioxides in moderate to good yields in MeOH. These reactions presumably proceed via DBU-catalyzed O-sulfonylation/intramolecular Baylis-Hillman/1,3-H shift or dehydration tandem sequences, respectively.

Synthesis, characterization and antibacterial activity of new sulfonyl hydrazone derivatives and their nickel(II) complexes

NASA Astrophysics Data System (ADS)

Özmen, Ümmühan Özdemir; Olgun, Gülçin

2008-08-01

Prophane sulfonic acid hydrazide (psh: CH 3CH 2CH 2SO 2NHNH 2) derivatives as salicylaldehydeprophanesulfonylhydrazone (salpsh), 5-methylsalicylaldehydeprophanesulfonylhydrazone (5-msalpsh), 2-hydroxyacetophenoneprophanesulfonylhydrazone (afpsh), 5-methyl-2-hydroxyacetophenoneprophanesulfonylhydrazone (5-mafpsh) and their Ni(II) complexes have been synthesized. The structure of these compounds has been investigated by using elemental analysis, FTIR, 1H NMR, LC/MS, UV-vis spectrophotometric method, magnetic susceptibility and conductivity measurements. The complexes were found to have general compositions [NiL2]. Square-planer structures are proposed for the Ni(II) complexes on the basis of magnetic evidence, electronic spectra and TGA data. Bacterial activities of sulfonyl hydrazone compounds were studied against gram-positive bacteria: Staphylococcus aureus, Bacillus subtilis, Bacillus magaterium and gram-negative bacteria: Salmonella enteritidis, Escherichia coli by using minimum inhibitory concentrations (MICs) method.

Exploiting the acylating nature of the imide-Ugi intermediate: a straightforward synthesis of tetrahydro-1,4-benzodiazepin-2-ones.

PubMed

Mossetti, Riccardo; Saggiorato, Dèsirèe; Tron, Gian Cesare

2011-12-16

We describe a simple and novel protocol for the synthesis of tetrahydro-1,4-benzodiazepin-2-ones with three points of diversity, exploiting the acylating properties of the recently rediscovered Ugi-imide. The final compounds can be easily prepared in three synthetic steps using a multicomponent reaction, a Staudinger reduction, and an acylative protocol, with good to excellent yields for each synthetic step.

1-Ethyl-1-methyl piperidinium bis(trifluoromethanesulfonyl)imide as a co-solvent in Li-ion batteries

NASA Astrophysics Data System (ADS)

Kim, Ketack; Cho, Young-Hyun; Shin, Heon-Cheol

2013-03-01

1-Ethyl-1-methyl piperidinium bis(trifluoromethanesulfonyl)imide (EMP-TFSI) is an ionic liquid with a melting temperature of 85 °C. Although it is a solid salt, it shows good miscibility with carbonate solvents, which allows EMP-TFSI to be used as a co-solvent in these systems. Ethylene carbonate is another solid co-solvent used in Li-ion batteries. Due to its smaller cationic size, EMP-TFSI provides better conductivity as a co-solvent than 1-methyl-1-propyl piperidinium bis(trifluoromethanesulfonyl)imide (MPP-TFSI), which is the smallest room-temperature piperidinium liquid salt known. In cells with 50 wt% IL and 50 wt% carbonate electrolyte, an EMP-TFSI mixed electrolyte performs better than an MPP-TFSI mixed electrolyte. Additionally, the discharge capacity values obtained from rate capability tests carried out with mixed EMP-TFSI are as good as those conducted with a pure carbonate electrolyte.

Distinct molecular structures and hydrogen bond patterns of α,α-diethyl-substituted cyclic imide, lactam, and acetamide derivatives in the crystalline phase

NASA Astrophysics Data System (ADS)

Krivoshein, Arcadius V.; Ordonez, Carlos; Khrustalev, Victor N.; Timofeeva, Tatiana V.

2016-10-01

α,α-Dialkyl- and α-alkyl-α-aryl-substituted cyclic imides, lactams, and acetamides show promising anticonvulsant, anxiolytic, and anesthetic activities. While a number of crystal structures of various α-substituted cyclic imides, lactams, and acetamides were reported, no in-depth comparison of crystal structures and solid-state properties of structurally matched compounds have been carried out so far. In this paper, we report molecular structure and intermolecular interactions of three α,α-diethyl-substituted compounds - 3,3-diethylpyrrolidine-2,5-dione, 3,3-diethylpyrrolidin-2-one, and 2,2-diethylacetamide - in the crystalline phase, as studied using single-crystal X-ray diffraction and IR spectroscopy. We found considerable differences in the patterns of H-bonding and packing of the molecules in crystals. These differences correlate with the compounds' melting points and are of significance to physical pharmacy and formulation development of neuroactive drugs.

Imide Oligomers Endcapped with Phenylethynl Phthalic Anhydrides and Polymers Therefrom

NASA Technical Reports Server (NTRS)

Hergenrother, Paul M. (Inventor); Smith, Joseph G., Jr. (Inventor)

1998-01-01

Controlled molecular weight phenylethynyl terminated imide oligomers (PETIs) have been prepared by the cyclodehydration of precursor phenylethynyl terminated amic acid oligomers. Amino terminated amic acid oligomers are prepared from the reaction of dianhydride(s) with an excess of diamine(s) and subsequently endcapped with phenylethynyl phthalic anhydride(s) (PEPA). The polymerizations are carried out in polar aprotic solvents such as N-methyl-2-pyrrolidinone or N.N-dimethylacetamide under nitrogen at room temperature. The amic acid oligomers are subsequently cyclodehydrated either thermally or cheznicauy to the corresponding imide oligomers. Direct preparation of PETIs from the reaction of dianhydxide(s) with an excess of diamine(s) and endcapped with phenylethynyl phthalic anhydride(s) has been performed in m-cresol. Phenylethynyl phthalic anhydrides are synthesized by the palladium catalyzed reaction of phenylacetylene with bromo substituted phthalic anhydrides in triethylamine. These new materials exhibit excellent properties and are potentially useful as adhesives, coatings, films, moldings and composite matrices.

Imide oligomers endcapped with phenylethynyl phthalic anhydrides and polymers therefrom

NASA Technical Reports Server (NTRS)

Hergenrother, Paul M. (Inventor); Smith, Jr., Joseph G. (Inventor)

1996-01-01

Controlled molecular weight phenylethynyl terminated imide oligomers (PETIs) have been prepared by the cyclodehydration of precursor phenylethynyl terminated amic acid oligomers. Amino terminated amic acid oligomers are prepared from the reaction of dianhydride(s) with an excess of diamine(s) and subsequently endcapped with phenylethynyl phthalic anhydride(s) (PEPA). The polymerizations are carried out in polar aprotic solvents such as N-methyl-2-pyrrolidinone or N,N-dimethylacetamide under nitrogen at room temperature. The amic acid oligomers are subsequently cyclodehydrated either thermally or chemically to the corresponding imide oligomers. Direct preparation of PETIs from the reaction of dianhydride(s) with an excess of diamine(s) and endcapped with phenylethynyl phthalic anhydride(s) has been performed in m-cresol. Phenylethynyl phthalic anhydrides are synthesized by the palladium catalyzed reaction of phenylacetylene with bromo substituted phthalic anhydrides in triethylamine. These new materials exhibit excellent properties and are potentially useful as adhesives, coatings, films, moldings and composite matrices.

Development and demonstration of manufacturing processes for fabricating graphite/Larc-160 polyimide structural elements, part 4, paragraph C

NASA Technical Reports Server (NTRS)

1981-01-01

Progress in the development of processes for production of Celion/LARC-160 graphite-polyimide materials, quality control methods, and the fabrication of Space Shuttle composite structure components is reported. The formulation and processing limits for three batches of resin are presented. Process improvements for simplification of the imidizing and autoclave cure cycles are described. Imidized and autoclave cured test panels were prepared. Celion/LARC-160 cure process verification and the fabrication of honeycomb sandwich panel elements and skin/stringer panels are described. C-scans of laminates imidized at 163 C to 218 C for periods from 30 to 180 minutes, and of process verification laminates made from different batches of prepreg are presented. Failure modes and load/strain characteristics of sandwich elements and C-scans of stringer to skin bond joints are also given.

Syntheses of Novel Nitrogen and Phosphorus Heterocycles.

DTIC Science & Technology

1985-04-26

some of the interaction products was associated with ammonia elimination. Depending on reaction conditions, specific phosphorus-containing compounds...19 3.5 Antioxidative and anticorrosive action of thiophenyl-substituted mono- and diphospha-s-triazine 21 3.6 Reactions of perfluoro-n-octanonitrile...addition compounds Both linear and cyclic materials were identified. The ation of some of the inter- action products was associated with ammonia

Comparative Toxicity of Halogenated Hydrocarbons: Molecular Aspects

DTIC Science & Technology

1993-07-13

peroxisome proliferators, namely perfluorooctanoic acid ( PFOA ), perfluorodecanoic acid ( PFDA ) and the tri-and tetra-oligomers of chlorotrifluooethylene...ACID ( PFOA ), PERFLUORO - DECANOIC ACID ( PFDA ) AND THE TRI-AND TETRA-OLIGOMERS OF CHLORO -TR.tLUORO ETHYLENE (CTFE) HAVE BEEN INVESTIGATED IN THE RAT AND...AVAILABILITY STATEMENT 12b. DISTRIBUTION CODE NO LIMITATION NOT KNOWN 13. ABSTRACT (Maximum 200 words) THE COMPARATIVE HEPATOTOXICITIES OF PERFLUOROOCTANOIC

Effects of Nonadecafluorodecanoic Acid on Tissue Fatty Acids of the Rat.

DTIC Science & Technology

1982-01-01

REVIEW Perfluorinated compounds have wide application. Perfluorocarboxylic and perfluorosulfonic acids have found commercial utilization in plating...readily obtainable in crystalline form. 1 Perfluorocarboxylic and perfluorosulfonic acids are used commercially in plating systems and as wetting agents...are generally considered to be metaboli- cally inert, but perfluorohexane causes reduction of microsomal cyto- chrome P-450 in vitro and perfluoro -n

Methods of forming single source precursors, methods of forming polymeric single source precursors, and single source precursors formed by such methods

DOEpatents

Fox, Robert V.; Rodriguez, Rene G.; Pak, Joshua J.; Sun, Chivin; Margulieux, Kelsey R.; Holland, Andrew W.

2016-04-19

Methods of forming single source precursors (SSPs) include forming intermediate products having the empirical formula 1/2{L.sub.2N(.mu.-X).sub.2M'X.sub.2}.sub.2, and reacting MER with the intermediate products to form SSPs of the formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2, wherein L is a Lewis base, M is a Group IA atom, N is a Group IB atom, M' is a Group IIIB atom, each E is a Group VIB atom, each X is a Group VIIA atom or a nitrate group, and each R group is an alkyl, aryl, vinyl, (per)fluoro alkyl, (per)fluoro aryl, silane, or carbamato group. Methods of forming polymeric or copolymeric SSPs include reacting at least one of HE.sup.1R.sup.1E.sup.1H and MER with one or more substances having the empirical formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2 or L.sub.2N(.mu.-X).sub.2M'(X).sub.2 to form a polymeric or copolymeric SSP. New SSPs and intermediate products are formed by such methods.

Methods of forming single source precursors, methods of forming polymeric single source precursors, and single source precursors formed by such methods

DOEpatents

Fox, Robert V.; Rodriguez, Rene G.; Pak, Joshua J.; Sun, Chivin; Margulieux, Kelsey R.; Holland, Andrew W.

2014-09-09

Methods of forming single source precursors (SSPs) include forming intermediate products having the empirical formula 1/2{L.sub.2N(.mu.-X).sub.2M'X.sub.2}.sub.2, and reacting MER with the intermediate products to form SSPs of the formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2, wherein L is a Lewis base, M is a Group IA atom, N is a Group IB atom, M' is a Group IIIB atom, each E is a Group VIB atom, each X is a Group VIIA atom or a nitrate group, and each R group is an alkyl, aryl, vinyl, (per)fluoro alkyl, (per)fluoro aryl, silane, or carbamato group. Methods of forming polymeric or copolymeric SSPs include reacting at least one of HE.sup.1R.sup.1E.sup.1H and MER with one or more substances having the empirical formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2 or L.sub.2N(.mu.-X).sub.2M'(X).sub.2 to form a polymeric or copolymeric SSP. New SSPs and intermediate products are formed by such methods.

Impact of Polymer Electrolyte Membrane Degradation Products on Oxygen Reduction Reaction Activity for Platinum Electrocatalysts

DOE PAGES

Christ, J. M.; Neyerlin, K. C.; Wang, H.; ...

2014-10-30

The impact of model membrane degradation compounds on the relevant electrochemical parameters for the oxygen reduction reaction (i.e. electrochemical surface area and catalytic activity), was studied for both polycrystalline Pt and carbon supported Pt electrocatalysts. Model compounds, representing previously published, experimentally determined polymer electrolyte membrane degradation products, were in the form of perfluorinated organic acids that contained combinations of carboxylic and/or sulfonic acid functionality. Perfluorinated carboxylic acids of carbon chain length C1 – C6 were found to have an impact on electrochemical surface area (ECA). The longest chain length acid also hindered the observed oxygen reduction reaction (ORR) performance, resultingmore » in a 17% loss in kinetic current (determined at 0.9 V). Model compounds containing sulfonic acid functional groups alone did not show an effect on Pt ECA or ORR activity. Lastly, greater than a 44% loss in ORR activity at 0.9V was observed for diacid model compounds DA-Naf (perfluoro(2-methyl-3-oxa-5-sulfonic pentanoic) acid) and DA-3M (perfluoro(4-sulfonic butanoic) acid), which contained both sulfonic and carboxylic acid functionalities.« less

Experimental measure of retinal impact force resulting from intraocular foreign body dropped onto retina through media of differing viscosity.

PubMed

Ernst, Benjamin J; Velez-Montoya, Raul; Kujundzic, Damir; Kujundzic, Elmira; Olson, Jeffrey L

2013-07-01

To evaluate and compare the perfluorocarbon liquid, silicone oil, and viscoelastic against standard saline, in their ability to dampen the impact force of a foreign body, dropped within the eye. In an experimental surgical model in where cohesive and adhesive forces of the substances are not enough to float heavy-than-water foreign bodies. A model of ophthalmic surgery was constructed. A BB pellet was dropped from 24 mm onto a force transducer through four different fluids: balanced salt solution, perfluoro-n-octane, viscoelastic, and silicone oil. The impact energy (force) for each case was measured and recorded by the force transducer. The mean force of impact for each fluid was compared using the Student t-test. Silicone oil resulted in the lowest force of impact. Both silicone oil and viscoelastic dampened the impact an order of magnitude more than perfluoro-n-octane and balanced salt solution. Silicone oil and viscoelastic cushioned the force from a dropped BB. They may be useful adjuncts to prevent iatrogenic retinal injury during vitrectomy for intraocular foreign body removal. © 2012 The Authors. Clinical and Experimental Ophthalmology © 2012 Royal Australian and New Zealand College of Ophthalmologists.

Photochemistry of matrix isolated (trifluoromethyl)sulfonyl azide, CF₃SO₂N₃.

PubMed

Zeng, Xiaoqing; Beckers, Helmut; Willner, Helge; Neuhaus, Patrik; Grote, Dirk; Sander, Wolfram

2015-03-19

The photochemistry of matrix isolated (trifluoromethylsulfonyl) azide, CF3SO2N3, has been studied at low temperatures. Upon ArF laser irradiation (λ = 193 nm), the azide eliminates N2 and furnishes triplet [(trifluoromethyl)sulfonyl]nitrene, CF3SO2N, which has been characterized by IR and EPR spectroscopy. Upon subsequent UV light irradiation (λ = 260-400 nm) the nitrene converts to CF3N═SO2 and CF3S(O)NO through a Curtius-type rearrangement. Further two new species CF2N═SO2F and FSNO were identified together with CF2NF, SO2, F2CO, CF3NO, and SO as side products. In addition, triplet nitrene CF3N was detected by its EPR and IR spectra. The complex stepwise photodecomposition of matrix isolated CF3SO2N3 is discussed in terms of the observed photolysis products and quantum chemical calculations.

Regioselective, borinic acid-catalyzed monoacylation, sulfonylation and alkylation of diols and carbohydrates: expansion of substrate scope and mechanistic studies.

PubMed

Lee, Doris; Williamson, Caitlin L; Chan, Lina; Taylor, Mark S

2012-05-16

Synthetic and mechanistic aspects of the diarylborinic acid-catalyzed regioselective monofunctionalization of 1,2- and 1,3-diols are presented. Diarylborinic acid catalysis is shown to be an efficient and general method for monotosylation of pyranoside derivatives bearing three secondary hydroxyl groups (7 examples, 88% average yield). In addition, the scope of the selective acylation, sulfonylation, and alkylation is extended to 1,2- and 1,3-diols not derived from carbohydrates (28 examples); the efficiency, generality, and operational simplicity of this method are competitive with those of state-of-the-art protocols including the broadly applied organotin-catalyzed or -mediated reactions. Mechanistic details of the organoboron-catalyzed processes are explored using competition experiments, kinetics, and catalyst structure-activity relationships. These experiments are consistent with a mechanism in which a tetracoordinate borinate complex reacts with the electrophilic species in the turnover-limiting step of the catalytic cycle.

Thermally resistant polymers for fuel tank sealants

NASA Technical Reports Server (NTRS)

Webster, J. A.

1973-01-01

Imide-linked perfluoroalkylene ether polymers, that were developed for the high temperature fuel tank sealant application, are discussed. Modifications of polymer structure and properties were realized through use of a new aromatic dianhydride intermediate containing an ether-linked perfluoroalkylene segment. Tests of thermal, oxidative and hydrolytic stability, fuel resistance, and adhesion are discussed along with tensile strength and elongation results. Efforts to effect a low temperature condensation of amic acid prepolymer to form imide links inside are described.

LaRC-RP41: A Tough, High-Performance Composite Matrix

NASA Technical Reports Server (NTRS)

Pater, Ruth H.; Johnston, Norman J.; Smith, Ricky E.; Snoha, John J.; Gautreaux, Carol R.; Reddy, Rakasi M.

1991-01-01

New polymer exhibits increased toughness and resistance to microcracking. Cross-linking PMR-15 and linear LaRC-TPI combined to provide sequential semi-2-IPN designated as LaRC-RP41. Synthesized from PMR-15 imide prepolymer undergoing cross-linking in immediate presence of LaRC-TPI polyamic acid, also undergoing simultaneous imidization and linear chain extension. Potentially high-temperature matrix resin, adhesive, and molding resin. Applications include automobiles, electronics, aircraft, and aerospace structures.

Discovery of the target for immunomodulatory drugs (IMiDs).

PubMed

Ito, Takumi; Ando, Hideki; Handa, Hiroshi

2016-05-01

Half a century ago, the sedative thalidomide caused a serious drug disaster because of its teratogenicity and was withdrawn from the market. However, thalidomide, which has returned to the market, is now used for the treatment of leprosy and multiple myeloma (MM) under strict control. The mechanism of thalidomide action had been a long-standing question. We developed a new affinity bead technology and identified cereblon (CRBN) as a thalidomide-binding protein. We found that CRBN functions as a substrate receptor of an E3 cullin-Ring ligase complex 4 (CRL4) and is a primary target of thalidomide teratogenicity. Recently, new thalidomide derivatives, called immunomodulatory drugs (IMiDs), have been developed by Celgene. Among them, lenalidomide (Len) and pomalidomide (Pom) were shown to exert strong therapeutic effects against MM. It was found that Len and Pom both bind CRBN-CRL4 and recruit neomorphic substrates (Ikaros and Aiolos). More recently it was reported that casein kinase 1a (Ck1a) was identified as a substrate for CRBN-CRL4 in the presence of Len, but not Pom. Ck1a breakdown explains why Len is specifically effective for myelodysplastic syndrome with 5q deletion. It is now proposed that binding of IMiDs to CRBN appears to alter the substrate specificity of CRBN-CRL4. In this review, we introduce recent findings on IMiDs.

Molecular Engineering of Perylene Imides for High-Performance Lithium Batteries: Diels-Alder Extension and Chiral Dimerization.

PubMed

Li, Lei; Hong, Yu-Jian; Chen, Dong-Yang; Lin, Mei-Jin

2017-11-21

The search for high-performance electrode materials in organic rechargeable batteries remains a key challenge. Reported herein is a molecular structural modification of perylene imides, a promising class of redox-active electrode materials, for improved battery performance. The Diels-Alder extension of perylene imides at the lateral position led to the simultaneous incorporation of two electron-withdrawing carbonyl groups and extension of the π system, which is supposed to favor high specific capacity, operating voltage, and electronic conductivity. After the chiral dimerization of the extended species with 1,2-diaminocyclohexane, it was anticipated that the porosity and coulombic interactions with lithium ions would be promoted, which would be beneficial for fast reaction kinetics and long cycling life. As expected, in lithium batteries, the obtained chiral and π-extended tweezer, which features six imide groups and a porous solid-state network of 42.2 % accessible cell volume, was found to deliver a reversible capacity of 92.1 mA h g -1 at a charge/discharge rate of 1 C within an operating voltage window of 1.60-2.80 V versus Li + /Li, around 75 and 50 % of which was maintained after 100 and 300 galvanostatic cycles, respectively, much better than those of unmodified species. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electrochemical Behavior of PEDOT/Lignin in Ionic Liquid Electrolytes: Suitable Cathode/Electrolyte System for Sodium Batteries.

PubMed

Casado, Nerea; Hilder, Matthias; Pozo-Gonzalo, Cristina; Forsyth, Maria; Mecerreyes, David

2017-04-22

Biomass-derived polymers, such as lignin, contain quinone/ hydroquinone redox moieties that can be used to store charge. Composites based on the biopolymer lignin and several conjugated polymers have shown good charge-storage properties. However, their performance has been only studied in acidic aqueous media limiting their applications mainly to supercapacitors. Here, we show that PEDOT/lignin (PEDOT: poly(3,4-ethylenedioxythiophene)) biopolymers are electroactive in aprotic ionic liquids (ILs) and we move a step further by assembling sodium full cell batteries using PEDOT/lignin as electrode material and IL electrolytes. Thus, the electrochemical activity and cycling of PEDOT/lignin electrodes was investigated in 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide (BMPyrTFSI), 1-butyl-1-methylpyrrolidinium bis(fluorosulfonyl)imide (BMPyrFSI), 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EMImTFSI) and 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)imide (EMImFSI) IL electrolytes. The effects of water and sodium salt addition to the ILs were investigated to obtain optimum electrolyte systems for sodium batteries. Finally, sodium batteries based on PEDOT/lignin cathode with imidazolium-based IL electrolyte showed higher capacity values than pyrrolidinium ones, reaching 70 mAhg -1 . Our results demonstrate that PEDOT/lignin composites can serve as low cost and sustainable cathode materials for sodium batteries. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Immune-mediated inflammatory diseases in patients with inflammatory bowel disease. Baseline data from the Aquiles study].

PubMed

Marín-Jiménez, Ignacio; García Sánchez, Valle; Gisbert, Javier P; Lázaro Pérez Calle, José; Luján, Marisol; Gordillo Ábalos, Jordi; Tabernero, Susana; Juliá, Berta; Romero, Cristina; Cea-Calvo, Luis; García-Vicuña, Rosario; Vanaclocha, Francisco

2014-11-01

To determine the prevalence of immune-mediated inflammatory diseases (IMID) in a cohort of patients with inflammatory bowel disease (IBD) enrolled in hospital gastroenterology outpatients units for the AQUILES study, a prospective 2-year follow-up study. We included patients ≥18 years old with a prior or new diagnosis of IBD (Crohn disease [CD], ulcerative colitis [UC] or indeterminate colitis). Diagnoses were collected in a cross-sectional manner from the clinical records at enrollment of a new patient in the study. We included 526 patients (mean age 40.2 years; 47.3% men, 52.7% women), 300 with CD (57.0%), 218 with UC (41.4%) and 8 with indeterminate colitis. Other types of IMID were present in 71 patients (prevalence: 13.5%, 95% CI: 10.8-16.7): 47 were spondyloarthropathies (prevalence: 8.9%); 18 psoriasis (3.4%); 5 pyoderma gangrenosum (1.0%), and 11 uveitis (2.1%). The prevalence of IMID was higher in patients with CD than in those with UC (17.0% [95% CI: 13.2-21.7] vs 9.2% [95% CI: 6.0-13.8], p=0.011). In the multivariate analysis, the variables associated with the presence of IMID were diagnosis of CD (OR=1.8 [95% CI: 1.1-3.2]) and duration of IBD ≥4 years (OR=2.1 [95% CI: 1.1-4.1] in those with disease duration 4-8 years, and OR=2.1 [95% CI: 1.2-3.9] in those with ≥8 years vs. <4 years). In the cohort of patients with IBD in the AQUILES study, 13.5% had another IMID, with a higher prevalence in patients with CD and>4 years since disease onset. Copyright © 2013 Elsevier España, S.L.U. and AEEH y AEG. All rights reserved.

Inorganic Halogen Oxidizer Research.

DTIC Science & Technology

1980-03-17

Synthesis, Novel Oxidizers, Solid-Propellant NF3 /F2 Gas Generators, Perfluoro- a- ammonium Salts, Perchlorates, Pentafluorooxouranate, Fluorosulfate...kcal mol I previously reported.’ by immersion into i constant-temperature 140.05 () circulating oil The fact that the small mole fraction ranges of...reactor higher tenperatures over almost t he entire nnole fraction () into the hot oil bath. the reactor was evacnaied. and the pressure range A mxpical

Synthesis and Characterization of Perfluoro Quaternary Ammonium Anion Exchange Membranes

DTIC Science & Technology

2012-01-01

study, new alkaline exchange membranes were prepared from the perfluorinated 3M ionomer with various quaternary ammonium cations attached with...ammonium anion exchange membranes Report Title ABSTRACT In this study, new alkaline exchange membranes were prepared from the perfluorinated 3M ionomer...exchange membranes were prepared from the perfluorinated 3M ionomer with vari- ous quaternary ammonium cations attached with sulfonamide linkage. The

AFOSR Technical Report Summaries, April-June 1986,

DTIC Science & Technology

1986-06-01

C1HARGE DENSITY. ELECTRODES. INTERrACIAL TENSION. PRESSURE, SIIRFACE PROPERTIES. CORROSION INHIBITION, MOLECULES, ORGANIC COMPOUNDS . SORPTION . FILMS... Perfluorinated derivatives of hydrocarbon Compounds usually ewhibit different propeties than their hydrocarbon analogues. The perfluoro crown ether-s are m.arkedly...Binary Hydrocarbon Mixtures, AD-A166 130 Materials for Emergency Repair AD-A167 094 of Runways. -BROMINE COMPOUNDS AD-Ai64 225 tCHEMICAL LASERS Analysis of

Permeation Testing of Materials With Chemical Agents or Simulants (Swatch Testing)

DTIC Science & Technology

2013-08-05

through a protective clothing material on a molecular level. Permeation involves the following: (1) sorption of molecules of the chemical into the...de Nemours and Company, Wilmington, Delaware), Teflon perfluoro- alkoxy ( PFA ), and Teflon polytetrafluoroethylene (PTFE). c. In all cases, only...pamphlet PCM positive control material PFA perfluoroalkoxy pH negative ion activity POL petroleum, oil, and lubricants PQL program quantification

Highly fluorinated polyurethanes

NASA Technical Reports Server (NTRS)

Stump, E. C., Jr.; Rochow, S. E. (Inventor)

1972-01-01

New polyurethanes containing a high degree of fluorine atoms are reported. The presence of the fluorine atoms in the polyurethane resins provides material having good thermal stability and chemical resistance. These polyurethanes are derived from a new hydroxy-terminated perfluoro polyether. The hydroxy terminated material is reacted with a diisocyanate to produce the polyurethanes. The polyurethanes can be used to form seals, coatings, potting material, hoses and the like.

Thyroid and Biochemical/Metabolic Effects of PFDA (Perfluoro-n-decanoic Acid).

DTIC Science & Technology

1988-01-04

could be explained by a chemically induced hypothyroidism. Experiments employing T4- supplementation suggests that the toxicity is more complex. Rats... supplementation was continued through the day prior to sacrifice. The liver enzymes c-glycerolphosphate dehydro- genase (GPD) and malic enzyme (ME) were...T4 supplementation had differential effects on anorexia, body wasting and hypothermia. Thyroxine supplementation completely prevented the PFDA-induced

PROCESS FOR PURIFYING CRUDE PERFLUOROCARBONS

DOEpatents

Holeton, R.E.

1959-03-24

A method is described for refining organic perfluoro compounds. In the manufacture of perfluorinated compounds by the fluorination of hydrocarbons, the product frequently is contaminated ny incompletely fluorimated hydrogen containing impurities. These impurities can be removed by contacting the products in a fluid conditions with an active adsorbents such as silica gel or alumina gel. The patent claims are restricted to this refining of crude perfluorinated lubricating oil.

Synthesis of new high performance lubricants and solid lubricants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lagow, Richard J.

1993-04-08

In our second year of funding we began the testing phase of a number of new classes of lubricants. Three different testing collaborations have already begun and a fourth one is In the works with Dr. Stephen Hsu of the National Institute of Standards and Technology. Dr. Hsu also plans to test some of the same materials for us that Shell Development is studying. With Dr. Bill Jones of NASA, we are studying the effects of branching an high temperature lubricant properties in perfluoropolyethers, Initially Bill Jones is comparing the lubrication and physical properties of perfluorotetraglyme and the following twomore » spherical perfluoropolyethers, Note that one contains a fluorocarbon chain and the other one contains a fluorocarbon ether chain. The synthesis of these was reported in the last progress report. With Professor Patricia Thiel of Iowa State University, we are working on studies of perfluoromethylene oxide ethers and have prepared a series of four of these polyethers to study in collaboration with her research group. These perfluoromethylene oxide ethers have the best low temperature properties of any known lubricants. Thiel's group is studying their interactions with metals under extreme conditions. Thirdly, we have also begun an Interaction with W. August Birke of Shell Development Company in Houston for whom we have already prepared samples of the chlorine-substituted fluorocarbon polyether lubricants whose structures appear on page 54 of our research proposal. Each of these four structures is thought to have potential as lubricant additives to motor oils. We also have underway syntheses of other fluorine-containing branched ether lubricants. These new materials which are also promising as antifriction additives for motor oils appear ahead of the perfluoro additives as Appendix I to the progress report. Additionally for Birke and Shell Development we have at their request prepared the novel compound perfluoro salicylic acid. This synthesis was suggested by the Shell staff who thought that esters of perfluoro salicylic acid might be an excellent antifriction additive for motor oil fuels. One of the best additives currently used in motor oils is the hydrocarbon ester of salicylic acid.« less

Rare Examples of Fe(IV) Alkyl-Imide Migratory Insertions: Impact of Fe-C Covalency in (Me2IPr)Fe(═NAd)R2 (R = neoPe, 1-nor).

PubMed

Jacobs, Brian P; Wolczanski, Peter T; Jiang, Quan; Cundari, Thomas R; MacMillan, Samantha N

2017-09-06

The iron(IV) imide complexes, (Me 2 IPr)-R 2 Fe=NAd (R = neo Pe (3a), 1-nor (3b)) undergo migratory insertion to iron(II) amides (Me 2 IPr)RFe{NR(Ad)} (R = neo Pe (4a), 1-nor (4b)) without evidence of imidyl or free nitrene character. By increasing the field strength about iron, odd-electron reactivity was circumvented via increased covalency.

Poly-phenylated diamines and their use as polycondensation monomers in the synthesis of polyamide, poly(amide-imide), and polyimide polymers

NASA Technical Reports Server (NTRS)

Harris, Frank W. (Inventor)

1992-01-01

New polyphenylated polynuclear aromatic diamines, such as 1,3-bis[4-aminophenyl]-2,3,5-triphenylbenzene, a process for their manufacture and their use as polycondensation components for the manufacture of polyamide, polyamide-imide and polyimide polymers are described. The polymers obtained with the aromatic diamines according to the invention are readily soluble, rigid-rod polymers and are distinguished by outstanding modulus, tensile compression strength, energy absorption, coefficient of expansion and electrical properties.

Imides: forgotten players in the Ugi reaction. One-pot multicomponent synthesis of quinazolinones.

PubMed

Mossetti, Riccardo; Pirali, Tracey; Saggiorato, Dèsirèe; Tron, Gian Cesare

2011-06-28

Up to now, the synthesis of quinazolinones has required lengthy synthetic procedures. Here, we describe an innovative one-pot multicomponent reaction leading to highly substituted quinazolinones. We believe that this novel transformation may open the door for the generation of new and pharmacologically active quinazolinones, but, most important of all, the resurrection of the imide-Ugi scaffold paves the way for the synthesis of novel molecular architectures. This journal is © The Royal Society of Chemistry 2011

The Effect of Molecular Weight on the Composite Properties of Cured Phenylethynyl Terminated Imide Oligomers

NASA Technical Reports Server (NTRS)

Smith, J. G., Jr.; Connell, J. W.; Hergenrother, P. M.

1997-01-01

As part of a program to develop high temperature/high performance structural resins for aeronautical applications, imide oligomers containing terminal phenylethynyl groups with calculated number average molecular weights of 1250, 2500 and 5000 g/mol were prepared, characterized, and evaluated as adhesives and composite matrix resins. The goal of this work was to develop resin systems that are processable using conventional processing equipment into void free composites that exhibit high mechanical properties with long term high temperature durability, and are not affected by exposure to common aircraft fluids. The imide oligomers containing terminal phenylethynyl groups were fabricated into titanium adhesive specimens and IM-7 carbon fiber laminates under 0.1 - 1.4 MPa for 1 hr at 350-371 C. The lower molecular weight oligomers exhibited higher cured Tg, better processability, and better retention of mechanical properties at elevated temperature without significantly sacrificing toughness or damage tolerance than the higher molecular weight oligomer. The neat resin, adhesive and composite properties of the cured polymers will be presented.

Immunomodulation of multiple myeloma.

PubMed

Tohnya, Tanyifor M; Figg, William D

2004-11-01

Multiple myeloma is a multi-process disease, and these different processes are responsible for the reduced sensitivity to chemotherapy and radiotherapy, hence the relapse and refractory nature of multiple myeloma. Emphasis is now placed on the hypothesis that myeloma cell growth, inhibition of apoptosis and drug resistance are dependent on immunomodulatory cytokines such as IL-6 and pro-angiogenic factors such as VEGF. In addition to its anti-angiogenic effects, the immunomodulatory properties of thalidomide make it a possible therapy for patients with advanced multiple myeloma. This has lead to the clinical development of a number of immunomodulatory thalidomide analogues (IMiDs) which are more potent and have less side effects than the parent drug, thalidomide. In the August 15(th) issue of Journal of Clinical Oncology, Schey SA et al. suggested that an IMiD (CC-4047) maybe efficacious due to T-cell co-stimulation, and safe in patients with relapsed or refractory multiple myeloma. This article demonstrates a supporting role for IMiDs as immunomodulatory adjuvant therapy.

Evaluation of new antimicrobial agents on Bacillus spp. strains: docking affinity and in vitro inhibition of glutamate-racemase.

PubMed

Tamay-Cach, Feliciano; Correa-Basurto, José; Villa-Tanaca, Lourdes; Mancilla-Percino, Teresa; Juárez-Montiel, Margarita; Trujillo-Ferrara, José G

2013-10-01

Three glutamic acid derivatives, two boron-containing and one imide-containing compound, were synthesized and tested for antimicrobial activity targeting glutamate-racemase. Antimicrobial effect was evaluated over Bacillus spp. Docking analysis shown that the test compounds bind near the active site of racemase isoforms, suggesting an allosteric effect. The boron derivatives had greater affinity than the imide derivative. In vitro assays shown good antimicrobial activity for the boron-containing compounds, and no effectiveness for the imide-containing compounds. The minimum inhibitory concentration of tetracycline, used as standard, was lower than that of the boron-containing derivatives. However, it seems that the boron-containing derivatives are more selective for bacteria. Experimental evidence suggests that the boron-containing derivatives act by inhibiting the racemase enzyme. Therefore, these test compounds probably impede the formation of the bacterial cell wall. Thus, the boron-containing glutamic acid derivatives should certainly be of interest for future studies as antimicrobial agents for Bacillus spp.

Spacer effect on nanostructures and self-assembly in organogels via some bolaform cholesteryl imide derivatives with different spacers

PubMed Central

2013-01-01

In this paper, new bolaform cholesteryl imide derivatives with different spacers were designed and synthesized. Their gelation behaviors in 23 solvents were investigated, and some of them were found to be low molecular mass organic gelators. The experimental results indicated that these as-formed organogels can be regulated by changing the flexible/rigid segments in spacers and organic solvents. Suitable combination of flexible/rigid segments in molecular spacers in the present cholesteryl gelators is favorable for the gelation of organic solvents. Scanning electron microscopy and atomic force microscopy observations revealed that the gelator molecules self-assemble into different aggregates, from wrinkle and belt to fiber with the change of spacers and solvents. Spectral studies indicated that there existed different H-bond formations between imide groups and assembly modes, depending on the substituent spacers in molecular skeletons. The present work may give some insight into the design and character of new organogelators and soft materials with special molecular structures. PMID:24083361

Spacer effect on nanostructures and self-assembly in organogels via some bolaform cholesteryl imide derivatives with different spacers

NASA Astrophysics Data System (ADS)

Jiao, Tifeng; Gao, Fengqing; Zhang, Qingrui; Zhou, Jingxin; Gao, Faming

2013-10-01

In this paper, new bolaform cholesteryl imide derivatives with different spacers were designed and synthesized. Their gelation behaviors in 23 solvents were investigated, and some of them were found to be low molecular mass organic gelators. The experimental results indicated that these as-formed organogels can be regulated by changing the flexible/rigid segments in spacers and organic solvents. Suitable combination of flexible/rigid segments in molecular spacers in the present cholesteryl gelators is favorable for the gelation of organic solvents. Scanning electron microscopy and atomic force microscopy observations revealed that the gelator molecules self-assemble into different aggregates, from wrinkle and belt to fiber with the change of spacers and solvents. Spectral studies indicated that there existed different H-bond formations between imide groups and assembly modes, depending on the substituent spacers in molecular skeletons. The present work may give some insight into the design and character of new organogelators and soft materials with special molecular structures.

The Wettability of LaRC Colorless Polyimide Resins on Casting Surfaces

NASA Technical Reports Server (NTRS)

Miner, Gilda A.; Stoakley, Diane M.; St.Clair, Anne K.; Gierow, Paul A.; Bates, Kevin

1997-01-01

Two colorless polyimides developed at NASA Langley Research Center, LaRC -CP1 and LaRC -CP2, are noted for being optically transparent, resistant to radiation, and soluble in the imide form. These materials may be used to make transparent, thin polymer films for building large space reflector/collector inflatable antennas, solar arrays, radiometers, etc. Structures such as these require large area, seamless films produced via spin casting or spray coating the soluble imide on a variety of substrates. The ability of the soluble imide to wet and spread over the mandrel or casting substrate is needed information for processing these structures with minimum waste and reprocessing, thereby, reducing the production costs. The wettability of a liquid is reported as the contact angle of the solid/liquid system. This fairly simple measurement is complicated by the porosity and the amount of contamination of the solid substrate. This work investigates the effect of inherent viscosity, concentration of polyimide solids, and solvent type on the wettability of various curing surfaces.

40 CFR Appendix A to Subpart G of... - Substitutes Subject to Use Restrictions and Unacceptable Substitutes

Code of Federal Regulations, 2010 CFR

2010-07-01

... Substitute Decision Comments Electronics cleaning w/CFC-113, MCF Perfluoro-carbons (C5F12, C6F12, C6F14... date); as of January 1, 1996, for uses in existing equipment. Electronics cleaning w/CFC-113 HCFC 141b... listings for CFC-113 past the effective date of the prohibition. Electronics cleaning w/MCF HCFC 141b and...

Toxicology of Perfluorodecanoic Acid

DTIC Science & Technology

1990-11-01

Perfluorodecanoic Acid ( PFOA ) and Thyroid Status. A. Statement of Problem: 1. Toxic doses of PFDA result in reduction of feed intake, body weight, serum...hypophagia and body weight loss). ii. Perfluoroaecanoic Acid ( PFOA ) and Lipid Metabolism in the Rat. A. Statement of Problem: 1. PFDA in a dose... perfluorinated acids are not available commercially. B. Objectives: 1. To synthesize perfluoro -n-decanoic acid ( PFDA ) with 14C-labeling in the C-I position. 2. To

Methods of forming single source precursors, methods of forming polymeric single source precursors, and single source precursors and intermediate products formed by such methods

DOEpatents

Fox, Robert V.; Rodriguez, Rene G.; Pak, Joshua J.; Sun, Chivin; Margulieux, Kelsey R.; Holland, Andrew W.

2012-12-04

Methods of forming single source precursors (SSPs) include forming intermediate products having the empirical formula 1/2{L.sub.2N(.mu.-X).sub.2M'X.sub.2}.sub.2, and reacting MER with the intermediate products to form SSPs of the formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2, wherein L is a Lewis base, M is a Group IA atom, N is a Group IB atom, M' is a Group IIIB atom, each E is a Group VIB atom, each X is a Group VIIA atom or a nitrate group, and each R group is an alkyl, aryl, vinyl, (per)fluoro alkyl, (per)fluoro aryl, silane, or carbamato group. Methods of forming polymeric or copolymeric SSPs include reacting at least one of HE.sup.1R.sup.1E.sup.1H and MER with one or more substances having the empirical formula L.sub.2N(.mu.-ER).sub.2M'(ER).sub.2 or L.sub.2N(.mu.-X).sub.2M'(X).sub.2 to form a polymeric or copolymeric SSP. New SSPs and intermediate products are formed by such methods.

An investigation of long and short range ion motions within the cluster morphology of electrolyte-containing perfluoro-sulfonate ionomer membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su, S.

1992-01-01

An equivalent circuit model was postulated for PFSI (perfluoro-sulfanate-ionomer) polymers. It successfully models three different dielectric relaxation mechanisms taking place within long and short sidechain PFSI's in an alternating electric field. The three dielectric processes are long-range ion inter-cluster hopping in the low frequency region, short-range intra-cluster polarization occurred in frequencies at about 10[sup 3] to 10[sup 6] Hz, and Debye-like orientation of water molecules taking place at very high frequencies. When membranes are annealed in the proximity of the glass transition temperature of ionic clusters, the packing of sulfonate groups becomes more efficient. This is by the fact thatmore » the symmetrical parameter of the distribution of relaxation time of the Cole-Cole equation increases with annealing time. The cluster activities of the long and short sidechain polymers act differently in different electrolyte solutions. The sidechains of the long sidechain polymer act like a spring, it contracts while the material was equilibrated in low concentration solutions and it expands as equilibrated in concentrated solutions. The cluster dimension of the long sidechain material does not vary too much. The cluster dimension of short sidechain polymers can vary significantly on different electrolyte solutions.« less

Prediction of the air-water partition coefficient for perfluoro-2-methyl-3-pentanone using high-level Gaussian-4 composite theoretical methods.

PubMed

Rayne, Sierra; Forest, Kaya

2014-09-19

The air-water partition coefficient (Kaw) of perfluoro-2-methyl-3-pentanone (PFMP) was estimated using the G4MP2/G4 levels of theory and the SMD solvation model. A suite of 31 fluorinated compounds was employed to calibrate the theoretical method. Excellent agreement between experimental and directly calculated Kaw values was obtained for the calibration compounds. The PCM solvation model was found to yield unsatisfactory Kaw estimates for fluorinated compounds at both levels of theory. The HENRYWIN Kaw estimation program also exhibited poor Kaw prediction performance on the training set. Based on the resulting regression equation for the calibration compounds, the G4MP2-SMD method constrained the estimated Kaw of PFMP to the range 5-8 × 10(-6) M atm(-1). The magnitude of this Kaw range indicates almost all PFMP released into the atmosphere or near the land-atmosphere interface will reside in the gas phase, with only minor quantities dissolved in the aqueous phase as the parent compound and/or its hydrate/hydrate conjugate base. Following discharge into aqueous systems not at equilibrium with the atmosphere, significant quantities of PFMP will be present as the dissolved parent compound and/or its hydrate/hydrate conjugate base.

The search of the target of promotion: Phenylbenzoate esterase activities in hen peripheral nerve

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moretto, A.; Nicolli, A.; Lotti, M.

2007-03-15

Certain esterase inhibitors, such as carbamates, phosphinates and sulfonyl halides, do not cause neuropathy as some organophosphates, but they may exacerbate chemical or traumatic insults to axons. This phenomenon is called promotion of axonopathies. Given the biochemical and toxicological characteristics of these compounds, the hypothesis was made that the target of promotion is a phenyl valerate (PV) esterase similar to neuropathy target esterase (NTE), the target of organophosphate induced delayed polyneuropathy. However, attempts to identify a PV esterase in hen peripheral nerve have been, so far, unsuccessful. We tested several esters, other than PV, as substrates of esterases from crudemore » homogenate of the hen peripheral nerve. The ideal substrate should be poorly hydrolysed by NTE but extensively by enzyme(s) that are insensitive to non-promoters, such as mipafox, and sensitive to promoters, such as phenyl methane sulfonyl fluoride (PMSF). When phenyl benzoate (PB) was used as substrate, about 65% of total activity was resistant to the non-promoter mipafox (up to 0.5 mM, 20 min, pH 8.0), that inhibits NTE and other esterases. More than 90% of this resistant activity was sensitive to the classical promoter PMSF (1 mM, 20 min, pH 8.0) with an IC{sub 50} of about 0.08 mM (20 min, pH 8.0). On the contrary, the non-promoter p-toluene sulfonyl fluoride caused only about 10% inhibition at 0.5 mM. Several esterase inhibitors including, paraoxon, phenyl benzyl carbamate, di-n-butyl dichlorovinyl phosphate and di-isopropyl fluorophosphate, were tested both in vitro and in vivo for inhibition of this PB activity. Mipafox-resistant PMSF-sensitive PB esterase activity(ies) was inhibited by promoters but not by non promoters and neuropathic compounds.« less

Effect of low water content in protic ionic liquid on ions electrosorption in porous carbon: application to electrochemical capacitors.

PubMed

Gorska, B; Timperman, L; Anouti, M; Béguin, F

2017-05-10

The effect of low water content (<20, 150, 1000, 10 000 ppm) in triethylammonium bis[(trifluoromethyl)sulfonyl]imide - [(C 2 H 5 ) 3 N + H][TFSI - ] - protic ionic liquid (PIL) on the performance of activated carbon (AC) electrodes as well as AC/AC electrochemical capacitors (ECs) is reported. Under negative polarization, hydrogen electrosorption onto carbon is enhanced along with the increase of water content in PIL, whereas the resulting desorption peaks are shifted to lower potential values, evidencing lower sorption energy when hydrogen is stored from moisture containing PIL. Cyclic voltammetry (CV) investigations on PIL-based ECs demonstrated that the evolution of the Stern layer nanostructure at positive and negative potentials is asymmetrical. The results revealed comparable electrochemical performance for PIL containing 150 and 1000 ppm of H 2 O, due to similar operation of the positive electrode, where [TFSI - ] anions are adsorbed in the outer Helmholtz plane, and the negative one, where hydrogen is stored through the reduction of the intermediate hydronium cation. By contrast, a cell with "dry" PIL (<20 ppm of water) displayed a distinctive operation due to hydrogen electrosorption directly through reduction of the protonated cation, and selective adsorption of [TFSI - ] anions, which occurs thanks to the high polarizability and image force (IF) created by their induced charge. Galvanostatic cycling with potential limitation (GCPL) showed comparable capacitance values whatever the water content in PILs up to 1000 ppm, yet electrochemical impedance spectroscopy (EIS) revealed higher capacitance as well as better retention at higher frequencies with the PIL containing 150 ppm of water. Hence, 150 ppm is reasoned to be an optimal value for diffusion and adsorption of ions. The nature of current collectors (aluminum or stainless steel) has a determining role in their polarization behavior, and consequently the potential range of electrodes as well as ion diffusion into the activated carbon porosity, influencing the observed capacitance values (C EIS/2.0V : 170 vs. 128 F g -1 , for Al and SSt, respectively).

Towards Organic Zeolites and Inclusion Catalysts: Heptazine Imide Salts Can Exchange Metal Cations in the Solid State.

PubMed

Savateev, Aleksandr; Pronkin, Sergey; Willinger, Marc Georg; Antonietti, Markus; Dontsova, Dariya

2017-07-04

Highly crystalline potassium (heptazine imides) were prepared by the thermal condensation of substituted 1,2,4-triazoles in eutectic salt melts. These semiconducting salts are already known to be highly active photocatalysts, for example, for the visible-light-driven generation of hydrogen from water. Herein, we show that within the solid-state structure, potassium ions can be exchanged to other metal ions while the crystal habitus is essentially preserved. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of benzimidazoles by PIDA-promoted direct C(sp2)-H imidation of N-arylamidines.

PubMed

Huang, Jinbo; He, Yimiao; Wang, Yong; Zhu, Qiang

2012-10-29

A metal-free synthesis of diversified benzimidazoles from N-arylamidines through a phenyliodine(III) diacetate (PIDA) promoted intramolecular direct C(sp(2))-H imidation has been developed. The reaction proceeds smoothly at 0 °C or ambient temperature to provide the desired products in good to excellent yields. The synthesis of 2-alkyl- or 2-alkyl-fused benzimidazoles, which are generally inaccessible by similar Pd- or Cu-catalyzed approaches, can also be achieved. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Low temperature electrodeposition of silicon layers

NASA Astrophysics Data System (ADS)

Pauporté, Thierry; Qi, Shuo; Viana, Bruno

2018-02-01

The electrodeposition of silicon at room temperature in 1-Butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide and N-Propyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide ionic liquids containing SiCl4 salt is shown. The electrodeposition window has been determined by cyclic voltammetry. Layers have been deposited in a three electrode cell placed in an inert atmosphere and at constant applied potential. The characterizations by x-ray diffraction and Raman spectroscopy showed the formation of a layer made of amorphous silicon. The scanning electron microscopy examination revealed that the layers were featureless and well-covering.

Electrolytes For Electrooptic Devices Comprising Ionic Liqu Ids

DOEpatents

Warner, Benjamin P.; McCleskey, T. Mark; Agrawal, Anoop; Cronin, John P.; Tonazzi, Juan C. L.; Burrell, Anthony K.

2005-02-08

Electrolyte solutions of soluble bifunctional redox dyes in molten salt solvent may be used to prepare electrooptic devices with enhanced stability toward ultraviolet radiation. The solvents include lithium or quaternary ammonium cations, and perfluorinated sulfonylimide anions selected from trifluoromethylsulfonate (CF.sub.3 SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3 SO.sub.2).sub.2 N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3 CF.sub.2 SO.sub.2).sub.2 N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3 SO.sub.2).sub.3 C.sup.-).

Characterization of the Terminal Iron(IV) Imides {[PhBPtBu2(pz’)]FeIV≡NAd}+

PubMed Central

Thomas, Christine M.; Mankad, Neal P.; Peters, Jonas C.

2008-01-01

New hybrid bis(phosphine)(pyrazole)borate tripodal ligands ([PhBPtBu2(pz’)]−) are reported that support pseudotetrahedral iron in the oxidation states +1, +2, +3, and +4. The higher oxidation states are stabilized by a terminal Fe≡NR linkage. Of particular interest is the generation and thorough characterization of an S = 1 FeIV≡NR+ imide cation using this new ligand system. The latter species can be observed electrochemically and spectroscopically, and its solid-state crystal structure is reported. PMID:16608321

Design and synthesis of positional isomers of 5 and 6-bromo-1-[(phenyl)sulfonyl]-2-[(4-nitrophenoxy)methyl]-1H-benzimidazoles as possible antimicrobial and antitubercular agents.

PubMed

Ranjith, P Karuvalam; Rajeesh, P; Haridas, Karickal R; Susanta, Nayak K; Row, Tayur N Guru; Rishikesan, R; Kumari, N Suchetha

2013-09-15

In this Letter, we report the structure-activity relationship (SAR) studies on series of positional isomers of 5(6)-bromo-1-[(phenyl)sulfonyl]-2-[(4-nitrophenoxy)methyl]-1H-benzimidazoles derivatives 7(a-j) and 8(a-j) synthesized in good yields and characterized by (1)H NMR, (13)C NMR and mass spectral analyses. The crystal structure of 7a was evidenced by X-ray diffraction study. The newly synthesized compounds were evaluated for their in vitro antibacterial activity against Staphylococcus aureus, (Gram-positive), Escherichia coli and Klebsiella pneumoniae (Gram-negative), antifungal activity against Candida albicans, Aspergillus flavus and Rhizopus sp. and antitubercular activity against Mycobacterium tuberculosis H37Rv, Mycobacterium smegmatis, Mycobacterium fortuitum and MDR-TB strains. The synthesized compounds displayed interesting antimicrobial activity. The compounds 7b, 7e and 7h displayed significant activity against Mycobacterium tuberculosis H37Rv strain. Copyright © 2013 Elsevier Ltd. All rights reserved.

Synthesis and Pharmacokinetic Evaluation of Siderophore Biosynthesis Inhibitors for Mycobacterium tuberculosis

PubMed Central

Nelson, Kathryn M.; Viswanathan, Kishore; Dawadi, Surendra; Duckworth, Benjamin P.; Boshoff, Helena I.; Barry, Clifton E.; Aldrich, Courtney C.

2015-01-01

MbtA catalyzes the first committed biosynthetic step of the mycobactins, which are important virulence factors associated with iron acquisition in Mycobacterium tuberculosis. MbtA is a validated therapeutic target for antitubercular drug development. 5′-O-[N-(salicyl)sulfamoyl]adenosine (1) is a bisubstrate inhibitor of MbtA and exhibits exceptionally potent biochemical and antitubercular activity. However, 1 suffers from sub-optimal drug disposition properties resulting in a short half-life (t1/2), low exposure (AUC), and low bioavailability (F). Four strategies were pursued to address these liabilities including the synthesis of prodrugs, increasing the pKa of the acyl-sulfonyl moiety, modulation of the lipophilicity, and strategic introduction of fluorine into 1. Complete pharmacokinetic (PK) analysis of all compounds was performed. The most successful modifications involved fluorination of the nucleoside that provided substantial improvements in t1/2 and AUC. Increasing the pKa of the acyl-sulfonyl linker yielded incremental enhancements while modulation of the lipophilicity and prodrug approaches led to substantially poorer PK parameters. PMID:26110337

High-Temperature and High-Energy-Density Dipolar Glass Polymers Based on Sulfonylated Poly(2,6-dimethyl-1,4-phenylene oxide).

PubMed

Zhang, Zhongbo; Wang, David H; Litt, Morton H; Tan, Loon-Seng; Zhu, Lei

2018-02-05

A new class of high-temperature dipolar polymers based on sulfonylated poly(2,6-dimethyl-1,4-phenylene oxide) (SO 2 -PPO) was synthesized by post-polymer functionalization. Owing to the efficient rotation of highly polar methylsulfonyl side groups below the glass transition temperature (T g ≈220 °C), the dipolar polarization of these SO 2 -PPOs was enhanced, and thus the dielectric constant was high. Consequently, the discharge energy density reached up to 22 J cm -3 . Owing to its high T g  , the SO 2 -PPO 25 sample also exhibited a low dielectric loss. For example, the dissipation factor (tan δ) was 0.003, and the discharge efficiency at 800 MV m -1 was 92 %. Therefore, these dipolar glass polymers are promising for high-temperature, high-energy-density, and low-loss electrical energy storage applications. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Remote C-H Activation of Quinolines through Copper-Catalyzed Radical Cross-Coupling.

PubMed

Xu, Jun; Shen, Chao; Zhu, Xiaolei; Zhang, Pengfei; Ajitha, Manjaly J; Huang, Kuo-Wei; An, Zhongfu; Liu, Xiaogang

2016-03-18

Achieving site selectivity in carbon-hydrogen (C-H) functionalization reactions is a formidable challenge in organic chemistry. Herein, we report a novel approach to activating remote C-H bonds at the C5 position of 8-aminoquinoline through copper-catalyzed sulfonylation under mild conditions. Our strategy shows high conversion efficiency, a broad substrate scope, and good toleration with different functional groups. Furthermore, our mechanistic investigations suggest that a single-electron-transfer process plays a vital role in generating sulfonyl radicals and subsequently initiating C-S cross-coupling. Importantly, our copper-catalyzed remote functionalization protocol can be expanded for the construction of a variety of chemical bonds, including C-O, C-Br, C-N, C-C, and C-I. These findings provide a fundamental insight into the activation of remote C-H bonds, while offering new possibilities for rational design of drug molecules and optoelectronic materials requiring specific modification of functional groups. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Inhibitory activity and mechanism of inhibition of the N-[[(4-benzoylamino)phenyl]sulfonyl]amino acid aldose reductase inhibitors.

PubMed

DeRuiter, J; Mayfield, C A

1990-11-15

A series of substituted N-[[(4-benzoylamino)phenyl]sulfonyl]amino acids (BAPS-amino acids) were synthesized by established methods, and the stereochemistry of the products was confirmed by HPLC analysis after chiral derivatization. When tested against aldose reductase (alditol:NADP+ oxidoreductase; EC 1.1.1.21; ALR2) isolated from rat lens, all of the BAPS-amino acids were determined to be significantly more inhibitory than the corresponding N-(phenylsulfonyl)amino acids. Structure-inhibition and enzyme kinetic analyses suggest that the BAPS-amino acids inhibit ALR2 by a mechanism similar to the N-(phenylsulfonyl)amino acids. However, multiple inhibition analyses indicate that the increased inhibitory activity of the BAPS-amino acids is a result of interaction with multiple sites present on ALR2. Enzyme specificity studies with several of the BAPS-amino acids demonstrated that these compounds do not produce significant inhibition of other nucleotide-requiring enzymes including aldehyde reductase (alcohol: NADP+ oxidoreductase; EC 1.1.1.2; ALR1).

Cross-Diels-Alder reactions of 6-oxo-1-sulfonyl-1,6-dihydropyridine-3-carboxylates.

PubMed

Teyssot, Marie-Laure; Lormier, Anh-Tuan; Chataigner, Isabelle; Piettre, Serge R

2007-03-30

Electron-poor 6-oxo-1-sulfonyl-1,6-dihydropyridine-3-carboxylates 1b-d undergo cross-Diels-Alder reactions with electron-rich dienes 4a-f under hyperbaric conditions, reacting either as dienophiles to yield normal-electron-demand (NED) cycloadducts 10 and/or 11 or as dienes to give inverse-electron-demand (IED) cycloadducts 12 and/or 13. The latter are converted into 14 and/or 15 through an NED cycloaddition with a second equivalent of electron-rich diene. Acyclic dienes display a propensity to yield NED products, whereas cyclic dienes tend to favor IED cycloadducts. High-pressure activation compares favorably with thermal or microwave activation in terms of both yields and suppression of the transformation of 1 into unreactive pyridines 3. Whereas the Cope rearrangement from IED to NED occurs under thermal conditions, no evidence of its involvement under high pressure could be detected. These and other data point to similar activation energies for the NED and IED processes under these conditions.

Palyosulfonoceramides A and B: Unique Sulfonylated Ceramides from the Brazilian Zoanthids Palythoa caribaeorum and Protopalyhtoa variabilis

PubMed Central

Almeida, Jose Gustavo L.; Maia, Ana Isabel V.; Wilke, Diego V.; Silveira, Edilberto R.; Braz-Filho, Raimundo; La Clair, James J.; Costa-Lotufo, Leticia V.; Pessoa, Otília Deusdenia L.

2012-01-01

The zoanthids Palythoa caribaeorum and Protopalythoa variabilis are among the most abundant marine species along the Brazilian coast. We now report the isolation and structure elucidation of two unprecedented sulfonylated ceramides, palyosulfonoceramide A (1) and palyosulfonoceramide B (2) from specimens collected off Brazil’s northeastern coast. The structures of 1 and 2 were established using a combination of NMR analyses, including: evaluation of 1H, 13C, 1H–1H COSY, 1H–13C HSQC, 1H–13C HMBC, and 1H–15N HMBC NMR spectra, high-resolution mass spectrometry and chemical degradation. In addition, we also isolated the corresponding known ceramides, N-((2S,3R,4E,8E)-1,3-dihydroxyoctadeca-4,8-dien-2-yl)-hexadecanamide (3) and N-((2S,3R,4E)-1,3-dihydroxyoctadeca-4-en-2-yl)-hexadecanamide (4), which provided further support for the assignments of 1 and 2. PMID:23242205

Palyosulfonoceramides A and B: unique sulfonylated ceramides from the Brazilian zoanthids Palythoa caribaeorum and Protopalythoa variabilis.

PubMed

Almeida, Jose Gustavo L; Maia, Ana Isabel V; Wilke, Diego V; Silveira, Edilberto R; Braz-Filho, Raimundo; La Clair, James J; Costa-Lotufo, Leticia V; Pessoa, Otília Deusdenia L

2012-12-14

The zoanthids Palythoa caribaeorum and Protopalythoa variabilis are among the most abundant marine species along the Brazilian coast. We now report the isolation and structure elucidation of two unprecedented sulfonylated ceramides, palyosulfonoceramide A (1) and palyosulfonoceramide B (2) from specimens collected off Brazil's northeastern coast. The structures of 1 and 2 were established using a combination of NMR analyses, including: evaluation of 1H, 13C, ¹H--¹H COSY, ¹H--¹³C HSQC, ¹H--¹³C HMBC, and ¹H--¹⁵N HMBC NMR spectra, high-resolution mass spectrometry and chemical degradation. In addition, we also isolated the corresponding known ceramides, N-((2S,3R,4E,8E)-1, 3-dihydroxyoctadeca-4,8-dien-2-yl)-hexadecanamide (3) and N-((2S,3R,4E)-1,3-dihydroxy octadeca-4-en-2-yl)-hexadecanamide (4), which provided further support for the assignments of 1 and 2.

Substituent effect on supramolecular motifs in series of succinimide polycyclic keto derivatives - Spectroscopic, theoretical and crystallographic studies

NASA Astrophysics Data System (ADS)

Miroslaw, Barbara; Koziol, Anna E.; Bielenica, Anna; Dziuba, Kamil; Struga, Marta

2014-09-01

The substituent effect on the supramolecular arrangement in a series of polycyclic monoimide keto derivatives crystals was studied. Single crystal X-ray diffraction and IR spectroscopic experiments were performed for seven related compounds, as well as the Hirshfeld surface analysis and quantum chemical calculations at HF and DFT levels in vacuo, in solution and for small clusters. The presence of Cdbnd O group at the bridge of the main hydrocarbon skeleton implied the catemer motif of the Nimidesbnd H⋯Oimide hydrogen bond in case of smaller substituents (Hsbnd , MeOsbnd , EtOsbnd ). For more voluminous groups (iBuOsbnd ) or additional hydrogen bond acceptors (AcOsbnd , Odbnd ) the steric hindrance increased and the imide⋯imide interactions were no longer present in the solid state. The Nimidesbnd H⋯Oketo or Nimidesbnd H⋯Oester hydrogen bonds were formed instead. The binding energy per one Nsbnd H⋯O interaction calculated for supramolecular clusters at HF/6-31G(d,p) level was ca. 20 kJ mol-1, indicating moderate strength of this hydrogen bond. The solvation free energies and induced dipole moments were computed at B3LYP/6-311+G(d,p) level using the integral equation formalism model (IEF PCM) considering three solvents of various polarity: non-polar chloroform, polar aprotic dimethyl sulfoxide (DMSO) and polar protic water. The relations between the vibrational spectra and the crystal structure have been discussed. The following sequence of carbonyl stretching modes in IR spectra has been derived from quantum chemical calculations: (1) at the highest frequencies - the symmetric vibration of two imide Cdbnd O bonds, (2) the vibrations of keto Cdbnd O bonds attached directly to the polycyclic hydrocarbon skeleton, (3) the asymmetric vibration of two imide Cdbnd O bonds, and (4) at the lowest frequencies - the vibration of ester Cdbnd O group. The characteristic peaks observed in imide experimental IR spectra at about 3080 cm-1 have been explained as overtone and combination bands of νCdbnd O stretching and γNsbnd H out-of-plane bending vibrations.

Immune-mediated inflammatory diseases and other comorbidities in patients with psoriasis: baseline characteristics of patients in the AQUILES study.

PubMed

Vanaclocha, F; Crespo-Erchiga, V; Jiménez-Puya, R; Puig, L; Sánchez-Carazo, J L; Ferrán, M; Sancho, C; Juliá, B; Cea-Calvo, L; Marín-Jiménez, I; García-Vicuña, R

2015-01-01

Patients with psoriasis often have comorbidities, including other immune-mediated inflammatory diseases (IMIDs), and cardiovascular risk factors. In this article we describe the baseline prevalence of comorbidities-including other IMIDs-in a cohort of patients with psoriasis. AQUILES was a prospective observational multicenter study of 3 patient cohorts (patients with psoriasis, spondyloarthritis, or inflammatory bowel disease) undertaken to investigate the prevalence of comorbidities, including other IMIDs, in these settings. The psoriasis cohort comprised patients aged at least 18 years who were seen in hospital dermatology clinics. A predefined protocol was used to collect demographic and clinical data. The study enrolled 528 patients with psoriasis (60.2% men and 39.8% women). Mean age was 46.7 years; 89.8% of the participants had plaque psoriasis, and the median Psoriasis Area Severity Index score (PASI) was 3.2 (1.5-7.4). Comorbid IMIDs were present in 82 (15.5%) of the patients (CI 95%, 12.7%-18.9%). Spondyloarthritis was observed in 14% of patients (95% CI, 11.3%-17.2%), mostly in the form of psoriatic arthritis, for which the overall prevalence was 13.1% (95% CI, 10.5%-16.2%). Inflammatory bowel disease was present in 1.3% (95% CI, 0.6%-2.7%) and uveitis in .2% (95% CI, 0.1%-1.4%). Psoriatic arthritis was associated with male sex (odds ratio, 1.75 [.98-2.98]) and a disease duration of over 8 years (OR, 4.17 [1.84-9.44] vs a duration of < 4 years). In 73.1%, at least 1 cardiovascular risk factor was identified: smoking (40.5%), obesity (26.0%), dyslipidemia (24.8%), hypertension (24.3%), and diabetes mellitus (12.3%). In patients with psoriasis the prevalence of other IMIDs was 15.5%, a level slightly higher than that found in the general population. Nearly three-quarters of these patients had at least 1 cardiovascular risk factor. Copyright © 2014 Elsevier España, S.L.U. and AEDV. All rights reserved.

Preliminary in vivo report on the osteocompatibility of poly(anhydride-co-imides) evaluated in a tibial model.

PubMed

Ibim, S E; Uhrich, K E; Attawia, M; Shastri, V R; El-Amin, S F; Bronson, R; Langer, R; Laurencin, C T

1998-01-01

A novel class of polymers with mechanical properties similar to cancellous bone are being investigated for their ability to be used in weight-bearing areas for orthopedic applications. The poly(anhydride-co-imide) polymers based on poly[trimellitylimidoglycine-co-1,6-bis(carboxyphenoxy)hexan e] (TMA-Gly:CPH) and poly[pyromellitylimidoalanine-co-1,6-bis(carboxyphenoxy)hexa ne] (PMA-Ala:CPH) in molar ratios of 30:70 were investigated for osteocompatibility, with effects on the healing of unicortical 3-mm defects in rat tibias examined over a 30-day period. Defects were made with surgical drill bits (3-mm diameter) and sites were filled with poly(anhydride-co-imide) matrices and compared to the control poly(lactic acid-glycolic acid) (PLAGA) (50:50), a well-characterized matrix frequently used in bone regeneration studies, and defects without polymeric implants. At predetermined time intervals (3, 6, 9, 12, 20, and 30 days), animals were sacrificed and tissue histology was examined for bone formation, polymer-tissue interaction, and local tissue response by light microscopy. The studies revealed that matrices of TMA-Gly:CPH and PMA-Ala:CPH produced responses similar to the control PLAGA with tissue compatibility characterized by a mild response involving neutrophils, macrophages, and giant cells throughout the experiment for all matrices studied. Matrices of PLAGA were nearly completely degraded by 21 days in contrast to matrices of TMA-Gly:CPH and PMA-Ala:CPH that displayed slow erosion characteristics and maintenance of shape. Defects in control rats without polymer healed by day 12, defects containing PLAGA healed after 20 days, and defects containing poly(anhydride-co-imide) matrices produced endosteal bone growth as early as day 3 and formed bridges of cortical bone around matrices by 30 days. In addition, there was marrow reconstitution at the defect site for all matrices studied along with matured bone-forming cells. This study suggests that novel poly(anhydride-co-imides) are promising polymers that may be suitable for use as implants in bone surgery, especially in weight-bearing areas.

Performance of solid state supercapacitors based on polymer electrolytes containing different ionic liquids

NASA Astrophysics Data System (ADS)

Tiruye, Girum Ayalneh; Muñoz-Torrero, David; Palma, Jesus; Anderson, Marc; Marcilla, Rebeca

2016-09-01

Four Ionic Liquid based Polymer Electrolytes (IL-b-PE) were prepared by blending a Polymeric Ionic Liquid, Poly(diallyldimethylammonium) bis(trifluoromethanesulfonyl)imide (PILTFSI), with four different ionic liquids: 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (PYR14TFSI) (IL-b-PE1), 1-butyl-1-methylpyrrolidinium bis(fluorosulfonyl)imide (PYR14FSI) (IL-b-PE2), 1-(2-hydroxy ethyl)-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (HEMimTFSI) (IL-b-PE3), and 1-Butyl-1-methylpyrrolidinium dicyanamide, (PYR14DCA) (IL-b-PE4). Physicochemical properties of IL-b-PE such as ionic conductivity, thermal and electrochemical stability were found to be dependent on the IL properties. For instance, ionic conductivity was significantly higher for IL-b-PE2 and IL-b-PE4 containing IL with small size anions (FSI and DCA) than IL-b-PE1 and IL-b-PE3 bearing IL with bigger anion (TFSI). On the other hand, wider electrochemical stability window (ESW) was found for IL-b-PE1 and IL-b-PE2 having ILs with electrochemically stable pyrrolidinium cation and FSI and TFSI anions. Solid state Supercapacitors (SCs) were assembled with activated carbon electrodes and their electrochemical performance was correlated with the polymer electrolyte properties. Best performance was obtained with SC having IL-b-PE2 that exhibited a good compromise between ionic conductivity and electrochemical window. Specific capacitance (Cam), real energy (Ereal) & real power densities (Preal) as high as 150 F g-1, 36 Wh kg-1 & 1170 W kg-1 were found at operating voltage of 3.5 V.

Preparation and Characterization of Polyimide/Organoclay Nanocomposites

NASA Technical Reports Server (NTRS)

Delozier, D. M.; Orwoll, R. A.; Cahoon, J. F.; Johnston, N. J.; Smith, J. G., Jr.; Connell, J. W.

2002-01-01

Organically modified montmorrrillonite clay, containing a long chain aliphatic quarternary ammonium cation, was used to prepare polyimide/organoclay hybrids. Several approaches were examined in an attempt to achieve fully exfoliated nanocomposites. These included simple mixing of the clay in a pre-made high molecular weight poly(amide acid) solution; simple mixing followed by sonication of the organoclay/poly(amide acid) solutions; and the preparation of high molecular weight poly(amide acid)s in the presence of the organoclay dispersed in N-methyl-2-pyrrolidinone (NMP). The best results were obtained using the in-situ polymerization approach. The resulting nanocomposite films (both amide acid and imide), containing 3-8% by weight of organoclay, were characterized by differential scanning calorimetry (DSC), dynamic thermogravimetric analysis (TGA), transmission electron microscopy (TEM), X-ray diffraction (XRD), and thin film tensile properties. A significant degree of dispersion was observed in the nanocomposite films of the amide acid and the imide. After thermal treatment of amide acid films to effect imidization, in both air and nitrogen, the films were visually darker than control films without clay and the level of clay dispersion appeared to have decreased. In the latter case, the separation between the layers of the clay decreased to a spacing less than that present in the original organoclay. These observations suggest that thermal degradation of the aliphatic quarternary ammonium cation occurred likely during thermal treatment to effect imidization and solvent removal. These thermal degradation effects were less pronounced when thermal treatment was performed under nitrogen. The polyimide/organoclay hybrid films exhibited higher room temperature tensile moduli and lower strength and elongation to break than the control films.

Synthesis of Perfluorinated Ethers by Solution Phase Direct Fluorination: An Adaptation of the La-Mar Technique

DTIC Science & Technology

1990-08-22

Six of the 3 perfluorinated ethers prepared have been previously synthesized by other methods: perfluoro -5,5-bis(ethoxy- f methyl) -3,7-dioxanonane...from partially fluorinated starting material [34]. Third, as with perfluoroalkanes and simple perfluoroethers , Clark’s experimental results indicated 3...a highly branched perfluoroether ) by direct fluorination 3 in solution. Second, since some of these perfluorinated compounds had been previously

Polyimides Based on Asymmetric Dianhydrides (II) (a-BPDA vs a-BTDA) for Resin Transfer Molding (RTM)

NASA Technical Reports Server (NTRS)

Chuang, Kathy C.; Criss, Jim M.; Mintz, Eric A.

2010-01-01

A new series of low-melt viscosity imide resins (10-20 poise at 280 C) were formulated from asymmetric 2,3,3',4' -benzophenone dianhydride (a-BTDA) and 4-phenylethynylphthalic endcaps, along with 3,4' -oxydianiline, 3,3' -methylenedianiline and 3,3'- diaminobenzophenone, using a solvent-free melt process. a-BTDA RTM resins exhibited higher glass transition temperatures (Tg's = 330-400 C) compared to those prepared by asymmetric 2,3,3',4' -biphenyl dianhydride, (a-BPDA, Tg's = 320-370 C). These low-melt viscosity imide resins were fabricated into polyimide/T650-35 carbon fiber composites by a RTM process. Composites properties of a-BTDA resins, such as open-hole compression and short-beam shear strength, are compared to those of composites made from a-BPDA based resin at room temperature, 288 C and 315 C. These novel, high temperature RTM imide resins exhibit outstanding properties beyond the performance of conventional RTM resins, such as epoxy and BMI resins which have use-temperatures around 177 C and 232 C for aerospace applications.

An investigation into the injection molding of PMR-15 polyimide

NASA Technical Reports Server (NTRS)

Colaluca, M. A.

1984-01-01

The chemorheological behavior of the PRM-15 molding compounds were characterized, the range of suitable processing parameters for injection molding in a reciprocating screw injection molding machine was determined, and the effects of the injection molding processing parameters on the mechanical properties of molded PMR-15 parts were studied. The apparatus and procedures for measuring viscosity and for determining the physical response of the material during heating are described. Results show that capillary rheometry can be effectively used with thermosets if the equipment is designed to overcome some of the inherent problems of these materials. A uniform temperature was provided in the barrel by using a circulating hot oil system. Standard capillary rheometry methods can provide the dependence of thermoset apparent viscosity on shear rate, temperature, and time. Process conditions resulting in complete imidization should be carefully defined. Specification of controlled oven temperature is inadequate and can result in incomplete imidization. For completely imidized PMR-15 heat at 15 C/min melt flow without gas evolution occurs in the temperature range of 325 C to 400 C.

Antiproliferative effects on human tumor cells and rat aortic smooth muscular cells of 2,3-heteroarylmaleimides and heterofused imides.

PubMed

Ferri, Nicola; Beccalli, Egle Maria; Contini, Alessandro; Corsini, Alberto; Antonino, Manuela; Radice, Tiziano; Pratesi, Graziella; Tinelli, Stella; Zunino, Franco; Gelmi, Maria Luisa

2008-02-15

A series of 2,3-heteroarylmaleimides 9 and polyheterocondensed imides 12 were prepared in good yields and short reaction time using a very efficient procedure consisting in the condensation of the corresponding anhydrides and N,N-diethylethylenediamine and microwave heating. The antiproliferative activity of the novel molecules was tested against human tumor cells (NCI-H460 lung carcinoma) and rat aortic smooth muscle cells (SMCs). The IC50 values for the novel molecules ranged from 0.08 to 13.9 microM in SMCs, and from 0.84 to 9 microM in the tumor cell line. The activity profile for compounds 9 and 12 is comparable to that obtained for amonafide in NCI-H460, except for fused imides 12b,i which proved to be about 10-fold more potent. Whereas, in rat SMCs, only the compound 12b was shown to be 10-fold more potent than amonafide. Instead 12c is equipotent to amonafide. These results suggest that the extended pi-system and the kind of heteroatom are essential in the binding with the molecular target.

Conformations of n-butyl imidazole: matrix isolation infrared and DFT studies.

PubMed

Ramanathan, N; Sundararajan, K; Sankaran, K

2015-03-15

Conformations of n-butyl imidazole (B-IMID) were studied using matrix isolation infrared spectroscopy by trapping in argon, xenon and nitrogen matrixes using an effusive nozzle source. The experimental studies were supported by DFT computations performed at the B3LYP/6-311++G(d,p) level. Computations identified nine unique minima for B-IMID, corresponding to conformers with tg(±)tt, tg(±)g(∓)t, tg(±)g(±)t, tg(±)tg(±), tg(±)tg(∓), tg(±)g(∓)g(∓), tg(±)g(±)g(±), tg(±)g(∓)g(±) and tg(±)g(±)g(∓) structures, given in order of increasing energy. Computations of the transition state structures connecting the higher energy conformers to the global minimum, tg(±)tt structure were carried out. The barriers for the conformer inter-conversion were found to be ∼2 kcal/mol. Natural Bond Orbital (NBO) analysis was performed to understand the reasons for conformational preferences in B-IMID. Copyright © 2014 Elsevier B.V. All rights reserved.

Targeting adequate thermal stability and fire safety in selecting ionic liquid-based electrolytes for energy storage.

PubMed

Chancelier, L; Diallo, A O; Santini, C C; Marlair, G; Gutel, T; Mailley, S; Len, C

2014-02-07

The energy storage market relating to lithium based systems regularly grows in size and expands in terms of a portfolio of energy and power demanding applications. Thus safety focused research must more than ever accompany related technological breakthroughs regarding performance of cells, resulting in intensive research on the chemistry and materials science to design more reliable batteries. Formulating electrolyte solutions with nonvolatile and hardly flammable ionic liquids instead of actual carbonate mixtures could be safer. However, few definitions of thermal stability of electrolytes based on ionic liquids have been reported in the case of abuse conditions (fire, shortcut, overcharge or overdischarge). This work investigates thermal stability up to combustion of 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([C1C4Im][NTf2]) and 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide ([PYR14][NTf2]) ionic liquids, and their corresponding electrolytes containing lithium bis(trifluoromethanesulfonyl)imide LiNTf2. Their possible routes of degradation during thermal abuse testings were investigated by thermodynamic studies under several experimental conditions. Their behaviours under fire were also tested, including the analysis of emitted compounds.

2,4 Diamino benzonitrile

NASA Technical Reports Server (NTRS)

Frost, Lawrence W. (Inventor)

1980-01-01

Deep curable polymers having heterocyclic ring systems such as isoindoloquinazolinedione ring systems prepared from novel cyanoimide polymers, most desirably 2'-cyanoimide polymers. Preferably the cyanoimide polymers are prepared from a diamine having at least one nitrile group in the two position to an amine group and a dianhydride having at least two cyclic anhydride groups. Copolymers may be prepared having other linkages, notably imide linkages, in addition to isoindoloquinazolinedione ring systems and/or other similar heterocyclic ring systems. The copolymers can be prepared by use of diamines containing one or more cyanoimide groupings and/or imide groups in their structure.

Durable electrooptic devices comprising ionic liquids

DOEpatents

Agrawal, Anoop; Cronin, John P.; Tonazzi, Juan C. L.; Warner, Benjamin P.; McCleskey, T. Mark; Burrell, Anthony K.

2005-11-01

Electrolyte solutions for electrochromic devices such as rear view mirrors and displays with low leakage currents are prepared using inexpensive, low conductivity conductors. Preferred electrolytes include bifunctional redox dyes and molten salt solvents with enhanced stability toward ultraviolet radiation. The solvents include lithium or quaternary ammonium cations, and perfluorinated sulfonylimide anions selected from trifluoromethylsulfonate (CF3SO3-), bis(trifluoromethylsulfonyl)imide ((CF3SO2)2N-), bis(perfluoroethylsulfonyl)imide ((CF3CF2SO2)2N-) and tris(trifluoromethylsulfonyl)methide ((CF3SO2)3C-). Electroluminescent, electrochromic and photoelectrochromic devices with nanostructured electrodes include ionic liquids with bifunctional redox dyes.

40 CFR 180.479 - Halosulfuron-methyl; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

... residues of the herbicide halosulfuron-methyl, methyl 3-chloro-5-[[[[(4,6-dimethoxy-2-pyrimidinyl)amino]carbonyl] amino] sulfonyl]-1-methyl-1H-pyrazole-4-carboxylate, and its metabolites and degradates in or on...-sulfamoylpyrazole-4-carboxylic acid, expressed as the stoichiometric equivalent of halosulfuron-methyl, in or on the...

Exposure to perfluorooctane sulfonate during pregnancy in rat and mouse. I: maternal and prenatal evaluations

EPA Science Inventory

Abstract: The maternal and developmental toxicities of perfluorooctane sulfonate (PFOS, C8F17SO3-) were evaluated in the rat and mouse. PFOS is an environmentally persistent compound used as a surfactant and occurs as a degradation product of both perfluorooctane sulfonyl fluorid...

Study on process and characterization of high-temperature resistance polyimide composite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pan, Ling-Ying; Zhao, Wei-Dong; Liu, Han-Yang

2016-05-18

A novel polyimide composite with upper-use temperature of 420°C was prepared by autoclave process. The thermogravimetic analysis and rheological properties of uncured polyimide resin powders were analyzed. The influences of process parameters and post-treatment process on the properties of composites were also investigated. The morphologies of polyimide composites after shear fracture were observed by scanning electron microscope (SEM). The high-temperature resistance of composite was characterized by dynamic mechanical thermal analyzer (DMTA). Results showed that the imidization reaction mainly occurred in the temperature range of 100°C~220°C, and the largest weight loss rate appearing at 145°C indicated a drastic imidization reaction occurred.more » The melt viscosity of polyimide resin decreased with increasing the temperature between 220°C ∼305°C, and then increased with the increase of temperature due to the molecular crosslinking reactions. The fiber volume contents and void contents could be effectively controlled by applying the pressure step by step. The fiber volume content was sensitive to the initial pressure (P{sub i}) during the imidization. The second-stage pressure (P{sub 2}) and the temperature for applying the P{sub 2} (T{sub 2}) during the imidization had a great effect on the void content of composite. Good mechanical properties and interfacial adhesion of polyimide composite could obtain by optimized process. The post-treatment process can obviously increase the high-temperature resistance of polyimide composite. The polyimide composite treated at 420°C exhibited good retention of mechanical properties at 420°C and had a glass transition temperature (Tg) of 456°C. The retentions of flexible strength, flexible modulus and short beam shear strength of polyimide composite at 420°C were 65%, 84% and 62% respectively.« less

Adherence to systemic therapies for immune-mediated inflammatory diseases in Lebanon: a physicians' survey from three medical specialties.

PubMed

Ammoury, Alfred; Okais, Jad; Hobeika, Mireille; Sayegh, Raymond B; Shayto, Rani H; Sharara, Ala I

2017-01-01

Immune-mediated inflammatory diseases (IMIDs) are chronic conditions that may cause tissue damage and disability, reduced quality of life and increased mortality. Various treatments have been developed for IMIDs, including immune modulators and targeted biologic agents. However, adherence remains suboptimal. An adherence survey was used to evaluate physicians' beliefs about adherence to medication in IMID and to evaluate if and how they manage adherence. The survey was distributed to 100 randomly selected physicians from three different specialties. Results were analyzed by four academic experts commissioned to develop an action plan to address practical and perceptual barriers to adherence, integrating it into treatment goals to maximize outcomes in IMID, thereby elevating local standards of care. Eighty-two physicians participated in this study and completed the questionnaire. Most defined adherence as compliance with prescribed treatment. Although the majority of surveyed physicians (74%) did not systematically measure adherence in their practice, 54% identified adherence as a treatment goal of equal or greater importance to therapeutic endpoints. Lack of time and specialized nursing support was reported as an important barrier to measuring adherence. The expert panel identified four key areas for action: 360° education (patient-nurse-physician), patient-physician communication, patient perception and concerns, and market access/cost. An action plan was developed centered on education and awareness, enhanced benefit-risk communication, development of adherence assessment tools and promotion of patient support programs. Nonadherence to medication is a commonly underestimated problem with important consequences. A customized target-based strategy to address the root causes of non-adherence is essential in the management of chronic immune-mediated diseases.

Characterization, liquid crystalline behavior, electrochemical and optoelectrical properties of new poly(azomethine)s and a poly(imide) with siloxane linkages

NASA Astrophysics Data System (ADS)

Iwan, Agnieszka; Schab-Balcerzak, Ewa; Pociecha, Damian; Krompiec, Michal; Grucela, Marzena; Bilski, Pawel; Kłosowski, Mariusz; Janeczek, Henryk

2011-11-01

New siloxane-containing poly(azomethine)s and a six-membered poly(imide) have been developed from siloxane-containing diamine with four different dialdehydes and 3,4,9,10-perylenetetracarboxylic dianhydride, and their thermotropic behavior, optoelectrical and electrochemical properties were examined. Mesomorphic behavior of the polymers was investigated via differential scanning calorimetry (DSC), polarizing optical microscopy (POM) and X-ray diffraction (WAXRD, SAXRD) studies. The electrochemical behavior of poly(azomethine)s and poly(imide) was studied by differential pulse voltammetry (DPV). The HOMO levels of these polymers were in the range of -5.13 to -5.90 eV. UV-vis properties of the polymers were investigated in solid state as thin films and in chloroform solution. Optical energy band gap ( Egopt.) was calculated from absorption spectra and absorption coefficients α. The photoluminescence properties (PL) of obtained polymers were studied in chloroform solution. The investigated poly(azomethine)s emitted blue light, while the poly(imide) emitted green light. The polymers were irradiated with a test dose of 1 Gy Co-60 gamma-rays to detect their thermoluminescence properties in the temperature range of 50-200 °C. Polymer monolayer (ITO/polymer/Al) and bulk heterojunction (BHJ) (ITO/polymer:PCBM/Al and ITO/PEDOT:PSS/polymer:PCBM/Al) devices were prepared with PAZ and PI used as active layers and I- U curves were measured in the dark and during irradiation with light (under illumination of 1000 W/m 2). Poly(azomethine)s were blended with [6,6]-phenyl C 61 butyric acid methyl ester (PCBM). Selected properties of the investigated polymers with siloxane linkages were compared with the polymers ( PAZ1a- PAZ3a, PIa) prepared from the same dialdehydes or dianhydride and poly(1,4-butanediol)bis(4-aminobenzoate).

40 CFR 180.517 - Fipronil; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

...)-(trifluoromethyl)sulfinyl]-1H-pyrazole-3-carbonitrile) and its metabolites 5-amino-1-[2,6-dichloro-4-(trifluoromethyl)phenyl]-4-[(trifluoromethyl) sulfonyl]-1H-pyrazole-3-carbonitrile and 5-amino-1-[2,6-dichloro-4-(trifluoromethyl) phenyl]-4-[(trifluoromethyl)thio]-1H-pyrazole-3-carbonitrile and its photodegradate 5-amino-1-(2...

Cu-catalyzed cross-coupling reactions of epoxides with organoboron compounds.

PubMed

Lu, Xiao-Yu; Yang, Chu-Ting; Liu, Jing-Hui; Zhang, Zheng-Qi; Lu, Xi; Lou, Xin; Xiao, Bin; Fu, Yao

2015-02-11

A copper-catalyzed cross-coupling reaction of epoxides with arylboronates is described. This reaction is not limited to aromatic epoxides, because aliphatic epoxides are also suitable substrates. In addition, N-sulfonyl aziridines can be successfully converted into the products. This reaction provides convenient access to β-phenethyl alcohols, which are valuable synthetic intermediates.

Fission Yeast Model Study for Dissection of TSC Pathway

DTIC Science & Technology

2010-04-01

prepared as follows. A total of 1010 cells were incubated at 37! for 1 hr in spheroplasts buffer [50 mm citrate–phosphate (pH 5.6) and 1.2 m sorbitol ...potassium acetate, and 0.1 m sorbitol ] containing 0.4 mm phenylmethyl- sulfonyl fluoride and 13 protease inhibitor cocktail (Nacalai Tesque) and downed

21 CFR 173.21 - Perfluorinated ion exchange membranes.

Code of Federal Regulations, 2014 CFR

2014-04-01

... treated to hydrolyze the sulfonyl fluoride group to the sulfonic acid. The Chemical Abstracts Service name of this polymer is ethane-sulfonic acid, 2-[1-[difluoro-[(tri-fluoro-ethenyl)oxy]-methyl]-1,2,2,2... used in contact with all types of liquid foods at temperatures not exceeding 70° (158 °F). (2) Maximum...

Hydrolysis, adsorption, and biodegradation of bensulfuron methyl under methanogenic conditions.

PubMed

Zhu, Fan-Ping; Duan, Jian-Lu; Yuan, Xian-Zheng; Shi, Xiao-Shuang; Han, Zhen-Lian; Wang, Shu-Guang

2018-05-01

Bensulfuron methyl (BSM), one of the most widely used herbicides in paddy soils, is frequently detected in natural and artificial aquatic systems. However, BSM transformation under methanogenic conditions has not been given sufficient attention. In this study, BSM elimination and transformation by anaerobic enrichment cultures were investigated. The results showed that BSM can be mineralized to methane through hydrolysis, adsorption, and biodegradation under a methanogenic environment. The adsorption led to protein static quenching in the extracellular polymeric substances (EPSs) of the enrichment cultures. Specifically, BSM mainly reacted with the amine, amide, amino acid, and amino sugar functional groups in proteins. BSM hydrolysis and biodegradation occurred through the breakage of the sulfonylurea bridge and sulfonyl amide linkage. The cleavage of the sulfonylurea bridge occurred in both hydrolysis and biodegradation, while the cleavage of the sulfonyl amide linkage only occurred in hydrolysis. These results elucidated the complex transformation of BSM under methanogenic conditions, which will advance the studies on sulfonylurea herbicide biotransformation and hazard assessment in the environment. Copyright © 2018 Elsevier Ltd. All rights reserved.

ipso-Hydroxylation and Subsequent Fragmentation: a Novel Microbial Strategy To Eliminate Sulfonamide Antibiotics

PubMed Central

Ricken, Benjamin; Cichocka, Danuta; Parisi, Martina; Lenz, Markus; Wyss, Dominik; Martínez-Lavanchy, Paula M.; Müller, Jochen A.; Shahgaldian, Patrick; Tulli, Ludovico G.; Kohler, Hans-Peter E.; Kolvenbach, Boris A.

2013-01-01

Sulfonamide antibiotics have a wide application range in human and veterinary medicine. Because they tend to persist in the environment, they pose potential problems with regard to the propagation of antibiotic resistance. Here, we identified metabolites formed during the degradation of sulfamethoxazole and other sulfonamides in Microbacterium sp. strain BR1. Our experiments showed that the degradation proceeded along an unusual pathway initiated by ipso-hydroxylation with subsequent fragmentation of the parent compound. The NADH-dependent hydroxylation of the carbon atom attached to the sulfonyl group resulted in the release of sulfite, 3-amino-5-methylisoxazole, and benzoquinone-imine. The latter was concomitantly transformed to 4-aminophenol. Sulfadiazine, sulfamethizole, sulfamethazine, sulfadimethoxine, 4-amino-N-phenylbenzenesulfonamide, and N-(4-aminophenyl)sulfonylcarbamic acid methyl ester (asulam) were transformed accordingly. Therefore, ipso-hydroxylation with subsequent fragmentation must be considered the underlying mechanism; this could also occur in the same or in a similar way in other studies, where biotransformation of sulfonamides bearing an amino group in the para-position to the sulfonyl substituent was observed to yield products corresponding to the stable metabolites observed by us. PMID:23835177

Spectroscopic (FTIR, FT-Raman), molecular electrostatic potential, NBO and HOMO-LUMO analysis of P-bromobenzene sulfonyl chloride based on DFT calculations

NASA Astrophysics Data System (ADS)

Jeyavijayan, S.

2015-02-01

The FTIR and FT-Raman spectra of P-bromobenzene sulfonyl chloride (P-BBSC) have been recorded in the regions 4000-400 cm-1 and 3500-50 cm-1, respectively. Utilizing the observed FTIR and FT-Raman data, a complete vibrational assignment and analysis of the fundamental modes of the compound were carried out. The optimum molecular geometry, harmonic vibrational frequencies, infrared intensities and Raman scattering activities, were calculated by density functional theory (DFT/B3LYP) method. A good agreement between experimental and calculated normal modes of vibrations has been observed. A detailed interpretation of the infrared and Raman spectra of P-BBSC is also reported based on total energy distribution (TED). Stability of the molecule arising from hyperconjugative interactions, charge delocalization have been analyzed using natural bond orbital (NBO) analysis. The MEP map shows the negative potential sites are on oxygen atoms as well as the positive potential sites are around the hydrogen atoms. The UV-vis spectral analysis of P-BBSC has also been done which confirms the charge transfer of the molecule.

Selective matrix metalloproteinase inhibitor, N-biphenyl sulfonyl phenylalanine hydroxamic acid, inhibits the migration of CD4+ T lymphocytes in patients with HTLV-I-associated myelopathy.

PubMed

Ikegami, Mayumi; Umehara, Fujio; Ikegami, Naohito; Maekawa, Ryuji; Osame, Mitsuhiro

2002-06-01

Matrix metalloproteinases (MMPs) have been reported to be involved in various inflammatory disorders. Previous studies revealed that MMP-2 and MMP-9 might play important roles in the breakdown of the blood-brain barrier (BBB) in the central nervous system (CNS) of patients with HTLV-I-associated myelopathy (HAM)/tropical spastic paraparesis (TSP). N-Biphenyl sulfonyl-phenylalanine hydroxamic acid (BPHA) selectively inhibits MMP-2, -9 and -14, but not MMP-1, -3 and -7. In the present study, we examined whether or not the selective MMP inhibitor BPHA could inhibit the heightened migrating activity of CD4+ T cells in HAM/TSP patients. The migration assay using an invasion chamber showed that migration of CD4+ T cells in HAM/TSP patients was inhibited by 25 microM BPHA. In addition, the inhibitory ratio of migrating CD4+ lymphocytes was higher in HAM patients compared to normal controls. These results suggest that the selective MMP inhibitor BPHA has therapeutic potential for HAM/TSP.

Cu-catalyzed multicomponent polymerization to synthesize a library of poly(N-sulfonylamidines).

PubMed

Lee, In-Hwan; Kim, Hyunseok; Choi, Tae-Lim

2013-03-13

We report a versatile Cu-catalyzed multicomponent polymerization (MCP) technique that enables the synthesis of high-molecular-weight, defect-free poly(N-sulfonylamidines) from monomers of diynes, sulfonyl azides, and diamines. Through a series of optimizations, we discovered that the addition of excess triethylamine and the use of N,N'-dimethylformamide as a solvent are key factors to ensure efficient MCP. Formation of cyclic polyamidines was a side reaction during polymerization, but it was readily controlled by using diynes or diamines with long or rigid moieties. In addition, this polymerization is highly selective for three-component reactions over click reactions. The combination of the above factors enables the synthesis of high-molecular-weight polymers, which was challenging in previous MCPs. All three kinds of monomers (diynes, sulfonyl azides, and diamines) are readily accessible and stable under the reaction conditions, with various monomers undergoing successful polymerization regardless of their steric and electronic properties. Thus, we synthesized various high-molecular-weight, defect-free polyamidines from a broad range of monomers while overcoming the limitations of previous MCPs, such as low conversion and defects in the polymer structures.

N-Sulfonyl-β-lactam hapten as an effective labeling reagent for aldolase mAb.

PubMed

Inokuma, Tsubasa; Fuller, Roberta P; Barbas, Carlos F

2015-04-15

Utilization of chemically programmed antibodies (cpAbs) is regarded to be one of the most efficient methods for the development of therapeutic systems. cpAbs can extend the half-life of programming reagents, activate immune systems via the Fc region of antibodies and achieve universal vaccination by attaching varieties of small, programmed molecules. In the current study, we aimed to develop a novel labeling reagent for the preparation of cpAbs and found that N-sulfonyl-β-lactams (NSBLs) were optimal. NSBL can be synthesized from readily available 4-(bromomethyl)benzenesulfonyl chloride via few simple manipulations and can label the aldolase monoclonal antibody (mAb) 84G3, which could not be labeled effectively by the conventional labeling reagent, N-acyl-β-lactam (NABL). We also demonstrated that the conjugate, which consists of mAb 84G3 and an NSBL bearing a biotin moiety, maintained strong binding activity to streptavidin. In addition, the stability assay of NSBL revealed that NSBLs can tolerate aqueous media without significant decomposition over 24h. Copyright © 2015 Elsevier Ltd. All rights reserved.

Adhesive Properties of Cured Phenylethynyl containing Imides

NASA Technical Reports Server (NTRS)

Chang, Alice C.

1997-01-01

As part of a program to develop structural adhesives for high performance aerospace applications, several phenylethynyl containing oligomer blends of Larc(TM) MPEI and a reactive plasticizer designated LaRC LV-1 21 were prepared and evaluated. The fully imidized blends exhibited minimum melt viscosity as low as 1000 poise at 371 C. Ti/Ti lap shear specimens fabricated at 316 C under 15 psi gave RT strength of approx. 4300 psi and no change in strength was observed at 177 C. The chemistry and properties of this new MPEI as well as some blends of MPEI with LV-121 are presented and compared to the linear version, LARC(TM)-PETI-5.

An Imide-Based Pentacyclic Building Block for n-Type Organic Semiconductors

DOE PAGES

Wu, Fu-Peng; Un, Hio-Ieng; Li, Yongxi; ...

2017-10-09

For this study a new electron-deficient unit with fused 5-heterocyclic ring was developed by replacing a cyclopenta-1,3-diene from electron-rich donor indacenodithiophene (IDT) with cyclohepta-4,6-diene-1,3-diimde unit. The imide bridging endows BBI with fixed planar configuration and both low the highest occupied molecular orbital (HOMO) (-6.24 eV) and the lowest unoccupied molecular orbit (LUMO) (-2.57 eV) energy levels. Organic field-effect transistors (OFETs) based on BBI polymers exhibit electron mobility up to 0.34 cm 2 V -1 s -1, which indicates that the BBI is a promising n-type building block for optoelectronics.

A Mild, Ferrocene-Catalyzed C–H Imidation of (Hetero)Arenes

PubMed Central

2015-01-01

A simple method for direct C–H imidation is reported using a new perester-based self-immolating reagent and a base-metal catalyst. The succinimide products obtained can be easily deprotected in situ (if desired) to reveal the corresponding anilines directly. The scope of the reaction is broad, the conditions are extremely mild, and the reaction is tolerant of oxidizable and acid-labile functionality, multiple heteroatoms, and aryl iodides. Mechanistic studies indicate that ferrocene (Cp2Fe) plays the role of an electron shuttle in the decomposition of the perester reagent, delivering a succinimidyl radical ready to add to an aromatic system. PMID:24654983

An Imide-Based Pentacyclic Building Block for n-Type Organic Semiconductors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Fu-Peng; Un, Hio-Ieng; Li, Yongxi

For this study a new electron-deficient unit with fused 5-heterocyclic ring was developed by replacing a cyclopenta-1,3-diene from electron-rich donor indacenodithiophene (IDT) with cyclohepta-4,6-diene-1,3-diimde unit. The imide bridging endows BBI with fixed planar configuration and both low the highest occupied molecular orbital (HOMO) (-6.24 eV) and the lowest unoccupied molecular orbit (LUMO) (-2.57 eV) energy levels. Organic field-effect transistors (OFETs) based on BBI polymers exhibit electron mobility up to 0.34 cm 2 V -1 s -1, which indicates that the BBI is a promising n-type building block for optoelectronics.

A naphthalimide fluorophore with efficient intramolecular PET and ICT processes: application in molecular logic.

PubMed

Wang, Haixia; Wu, Haixia; Xue, Lin; Shi, Yan; Li, Xiyou

2011-08-07

A novel 4-amino-1,8-naphthalimide (NDI) with two different metal cation receptors connected at 4-amino or imide nitrogen positions respectively was designed and prepared. Significant internal charge transfer (ICT) as well as photoinduced electron transfer (PET) from the receptors to NDI is revealed by the shifted UV-vis absorption spectra and significant fluorescence quenching. Both Zn(2+) and Cu(2+) can coordinate selectively with the two cation receptors in this molecule with different affinities. The coordination of Zn(2+) with the receptor at imide nitrogen hindered the PET process and accordingly restored the quenched fluorescence of NDI. But the coordination of Zn(2+) at 4-amino position blocked the ICT process and caused significant blue-shift on the absorption peak with the fluorescence intensity unaffected. Similarly, coordination of Cu(2+) with the receptor at imide nitrogen can block the PET process, but can not restore the quenched fluorescence of compound 3 due to the paramagnetic properties of Cu(2+), which quench the fluorescence significantly instead. With Cu(2+) and Zn(2+) as two chemical inputs and absorption or fluorescence as output, several logic gate operations, such as OR, NOR and INHIBIT, can be achieved.

Perspectives in the treatment of multiple myeloma.

PubMed

Gentile, Massimo; Recchia, Anna Grazia; Mazzone, Carla; Lucia, Eugenio; Vigna, Ernesto; Morabito, Fortunato

2013-06-01

The development of proteasome inhibitor (PI) and immunomodulatory drugs (IMiDs) and advances in supportive care have considerably changed the treatment paradigm of multiple myeloma (MM) and significantly improved survival. Nevertheless, almost all patients show disease relapse and develop drug resistance. We review the prognostic stratification and therapeutic strategy for newly diagnosed MM patients. Furthermore, mechanisms of drug resistance are discussed. Data regarding newer drugs, currently undergoing examination, such as PI (carfilzomib, ONX0912, MLN9708, and marizomib), IMiDs (pomalidomide), histone deacetylase inhibitors (vorinostat and panobinostat), kinase inhibitors (temsirolimus, everolimus, and tanespimycin), and immune-based therapies (elotuzumab, siltuximab, MOR03087, and MMBT062) are reported. The use of three to four drug combination therapies including PI and IMiDs has significantly impacted on MM patient outcome. Moreover, new insights into MM biology from high-throughput technologies and availability of newer and more efficacious drugs will continue to influence our approach to MM treatment. In the immediate future molecular subgroup-specific trials using targeted agents may represent a very important step toward evaluating impact of interfering with relevant signaling pathways in MM. With the continued rapid evolution of progress in this field, MM will become a chronic illness having sustained complete response in a significant number of patients.

Homogeneous Liquid–Liquid Extraction of Rare Earths with the Betaine—Betainium Bis(trifluoromethylsulfonyl)imide Ionic Liquid System

PubMed Central

Hoogerstraete, Tom Vander; Onghena, Bieke; Binnemans, Koen

2013-01-01

Several fundamental extraction parameters such as the kinetics and loading were studied for a new type of metal solvent extraction system with ionic liquids. The binary mixture of the ionic liquid betainium bis(trifluoromethylsulfonyl)imide and water shows thermomorphic behavior with an upper critical solution temperature (UCST), which can be used to avoid the slower mass transfer due to the generally higher viscosity of ionic liquids. A less viscous homogeneous phase and mixing on a molecular scale are obtained when the mixture is heated up above 55 °C. The influence of the temperature, the heating and cooling times, were studied for the extraction of neodymium(III) with betaine. A plausible and equal extraction mechanism is proposed in bis(trifluoromethylsulfonyl)imide, nitrate, and chloride media. After stripping of the metals from the ionic liquid phase, a higher recovery of the ionic liquid was obtained by salting-out of the ionic liquid fraction lost by dissolution in the aqueous phase. The change of the upper critical solution temperature by the addition of HCl or betaine was investigated. In addition, the viscosity was measured below and above the UCST as a function of the temperature. PMID:24169434

Self-Assembly and Nanostructures in Organogels Based on a Bolaform Cholesteryl Imide Compound with Conjugated Aromatic Spacer

PubMed Central

Jiao, Ti-Feng; Gao, Feng-Qing; Shen, Xi-Hai; Zhang, Qing-Rui; Zhang, Xian-Fu; Zhou, Jing-Xin; Gao, Fa-Ming

2013-01-01

The self-assembly of small functional molecules into supramolecular structures is a powerful approach toward the development of new nanoscale materials and devices. As a class of self-assembled materials, low weight molecular organic gelators, organized in special nanoarchitectures through specific non-covalent interactions, has become one of the hot topics in soft matter research due to their scientific values and many potential applications. Here, a bolaform cholesteryl imide compound with conjugated aromatic spacer was designed and synthesized. The gelation behaviors in 23 solvents were investigated as efficient low-molecular-mass organic gelator. The experimental results indicated that the morphologies and assembly modes of as-formed organogels can be regulated by changing the kinds of organic solvents. Scanning electron microscopy and atomic force microscopy observations revealed that the gelator molecule self-assemble into different aggregates, from wrinkle and belt to fiber with the change of solvents. Spectral studies indicated that there existed different H-bond formations between imide groups and assembly modes. Finally, some rational assembly modes in organogels were proposed and discussed. The present work may give some insight to the design and character of new organogelators and soft materials with special structures. PMID:28788428

Small quaternary alkyl phosphonium bis(fluorosulfonyl)imide ionic liquid electrolytes for sodium-ion batteries with P2- and O3-Na2/3[Fe2/3Mn1/3]O2 cathode material

NASA Astrophysics Data System (ADS)

Hilder, Matthias; Howlett, Patrick C.; Saurel, Damien; Gonzalo, Elena; Armand, Michel; Rojo, Teófilo; Macfarlane, Douglas R.; Forsyth, Maria

2017-05-01

A saturated solution of 2.3 M sodium bis(fluorosulfonyl)imide in trimethyl iso-butyl phosphonium bis(fluorosulfonyl)imide ionic liquid shows a high conductivity (0.94 mScm-1 at 50 °C), low ion association, and a wide operational temperature window (-71 °C-305 °C) making it a promising electrolyte for sodium battery applications. Cycling with P2- and O3-Na2/3[Fe2/3Mn1/3]O2 cathode display excellent performance at 50 °C outperforming conventional organic solvent based electrolytes in terms of capacities (at C/10) and long term cycle stability (at C/2). Post analysis of the electrolyte shows no measurable changes while the sodium metal anode and the cathode surface shows the presence of electrolyte specific elements after cycling, suggesting the formation of a stabilizing solid electrolyte interface. Additionally, cycling changes the topography and particle morphology of the cathode. Thus, the electrolyte properties and cell performance match or outperform previously reported results with the additional benefit of replacing the hazardous and flammable organic solvent solutions commonly employed.

Rational combination treatment with histone deacetylase inhibitors and immunomodulatory drugs in multiple myeloma.

PubMed

Hideshima, T; Cottini, F; Ohguchi, H; Jakubikova, J; Gorgun, G; Mimura, N; Tai, Y-T; Munshi, N C; Richardson, P G; Anderson, K C

2015-05-15

Immunomodulatory drugs (IMiDs) thalidomide, lenalidomide (Len) and pomalidomide trigger anti-tumor activities in multiple myeloma (MM) by targetting cereblon and thereby impacting IZF1/3, c-Myc and IRF4. Histone deacetylase inhibitors (HDACi) also downregulate c-Myc. We therefore determined whether IMiDs with HDACi trigger significant MM cell growth inhibition by inhibiting or downregulating c-Myc. Combination treatment of Len with non-selective HDACi suberoylanilide hydroxamic acid or class-I HDAC-selective inhibitor MS275 induces synergic cytotoxicity, associated with downregulation of c-Myc. Unexpectedly, we observed that decreased levels of cereblon (CRBN), a primary target protein of IMiDs, was triggered by these agents. Indeed, sequential treatment of MM cells with MS275 followed by Len shows less efficacy than simultaneous treatment with this combination. Importantly ACY1215, an HDAC6 inhibitor with minimal effects on class-I HDACs, together with Len induces synergistic MM cytotoxicity without alteration of CRBN expression. Our results showed that only modest class-I HDAC inhibition is able to induce synergistic MM cytotoxicity in combination with Len. These studies may provide the framework for utilizing HDACi in combination with Len to both avoid CRBN downregulation and enhance anti-MM activities.

Studies on the intramolecular cyclizations of bicyclic delta-hydroxynitriles promoted by triflic anhydride.

PubMed

Justribó, Valeria; Pellegrinet, Silvina C; Colombo, María I

2007-05-11

Studies have been conducted to investigate the reactivity of several bicyclic delta-hydroxynitriles with triflic anhydride in dichloromethane. The reactions of the analogues derived from 1-indanone and 1-tetralone lead to annulated enones. These products arise from an initial elimination reaction that generates an alkene, followed by the addition of the carbon-carbon double bond to the activated cyano group. The intramolecular cyclization of the derivative obtained from 1-benzosuberone unexpectedly followed a different path, giving a cyclic imidate as the major product. In this case, the activated cyano group is directly attacked by the hydroxyl group of the starting delta-hydroxynitrile. Theoretical calculations provide a rationale for the observed reactivity pattern. Both the formation of the triflate via its protonated form, its subsequent ionization to the carbocation, and the cyclization of the resulting alkene to the enone become less favorable when the size of the ring increases due to conformational effects. The opposite trend is observed for the competing Pinner-type cyclization to the imidate. An alternative mechanism for the formation of the lactams from the cyclic imidates under acid-catalyzed conditions has also been proposed.

Combinations of fluorinated solvents with imide salts or methide salts for electrolytes

DOEpatents

Tikhonov, Konstantin; Yip, Ka Ki; Lin, Tzu-Yuan; Lei, Norman; Guerrero-Zavala, Guillermo; Kwong, Kristie W

2015-11-10

Provided are electrochemical cells and electrolytes used to build such cells. The electrolytes include imide salts and/or methide salts as well as fluorinated solvents capable of maintaining single phase solutions at between about -30.degree. C. to about 80.degree. C. The fluorinated solvents, such as fluorinated carbonates, fluorinated esters, and fluorinated esters, are less flammable than their non-fluorinated counterparts and improve safety characteristics of cells containing these solvents. The amount of fluorinated solvents in electrolytes may be between about 30% and 80% by weight not accounting weight of the salts. Linear and cyclic imide salts, such as LiN(SO.sub.2CF.sub.2CF.sub.3).sub.2, and LiN(SO.sub.2CF.sub.3).sub.2, as well as methide salts, such as LiC(SO.sub.2CF.sub.3).sub.3 and LiC(SO.sub.2CF.sub.2CF.sub.3).sub.3, may be used in these electrolytes. Fluorinated alkyl groups enhance solubility of these salts in the fluorinated solvents. In some embodiments, the electrolyte may also include a flame retardant, such as a phosphazene, and/or one or more ionic liquids.

Capacity-building and clinical competence in infectious disease in Uganda: a mixed-design study with pre/post and cluster-randomized trial components.

PubMed

Weaver, Marcia R; Crozier, Ian; Eleku, Simon; Makanga, Gyaviira; Mpanga Sebuyira, Lydia; Nyakake, Janepher; Thompson, MaryLou; Willis, Kelly

2012-01-01

Best practices for training mid-level practitioners (MLPs) to improve global health-services are not well-characterized. Two hypotheses were: 1) Integrated Management of Infectious Disease (IMID) training would improve clinical competence as tested with a single arm, pre-post design, and 2) on-site support (OSS) would yield additional improvements as tested with a cluster-randomized trial. Thirty-six Ugandan health facilities (randomized 1∶1 to parallel OSS and control arms) enrolled two MLPs each. All MLPs participated in IMID (3-week core course, two 1-week boost sessions, distance learning). After the 3-week course, OSS-arm trainees participated in monthly OSS. Twelve written case scenarios tested clinical competencies in HIV/AIDS, tuberculosis, malaria, and other infectious diseases. Each participant completed different randomly-assigned blocks of four scenarios before IMID (t0), after 3-week course (t1), and after second boost course (t2, 24 weeks after t1). Scoring guides were harmonized with IMID content and Ugandan national policy. Score analyses used a linear mixed-effects model. The primary outcome measure was longitudinal change in scenario scores. Scores were available for 856 scenarios. Mean correct scores at t0, t1, and t2 were 39.3%, 49.1%, and 49.6%, respectively. Mean score increases (95% CI, p-value) for t0-t1 (pre-post period) and t1-t2 (parallel-arm period) were 12.1 ((9.6, 14.6), p<0.001) and -0.6 ((-3.1, +1.9), p = 0.647) percent for OSS arm and 7.5 ((5.0, 10.0), p<0.001) and 1.6 ((-1.0, +4.1), p = 0.225) for control arm. The estimated mean difference in t1 to t2 score change, comparing arm A (participated in OSS) vs. arm B was -2.2 ((-5.8, +1.4), p = 0.237). From t0-t2, mean scores increased for all 12 scenarios. Clinical competence increased significantly after a 3-week core course; improvement persisted for 24 weeks. No additional impact of OSS was observed. Data on clinical practice, facility-level performance and health outcomes will complete assessment of overall impact of IMID and OSS. ClinicalTrials.gov NCT01190540.

Effect of integrated capacity-building interventions on malaria case management by health professionals in Uganda: a mixed design study with pre/post and cluster randomized trial components.

PubMed

Mbonye, Martin Kayitale; Burnett, Sarah M; Burua, Aldomoro; Colebunders, Robert; Crozier, Ian; Kinoti, Stephen N; Ronald, Allan; Naikoba, Sarah; Rubashembusya, Timothy; Van Geertruyden, Jean-Pierre; Willis, Kelly S; Weaver, Marcia R

2014-01-01

The Integrated Infectious Diseases Capacity Building Evaluation (IDCAP) designed two interventions: Integrated Management of Infectious Disease (IMID) training program and On-Site Support (OSS). We evaluated their effects on 23 facility performance indicators, including malaria case management. IMID, a three-week training with two follow-up booster courses, was for two mid- level practitioners, primarily clinical officers and registered nurses, from 36 primary care facilities. OSS was two days of training and continuous quality improvement activities for nine months at 18 facilities, to which all health workers were invited to participate. Facilities were randomized as clusters 1∶1 to parallel OSS "arm A" or control "arm B". Outpatient data on four malaria case management indicators were collected for 14 months. Analysis compared changes before and during the interventions within arms (relative risk = RR). The effect of OSS was measured with the difference in changes across arms (ratio of RR = RRR). The proportion of patients with suspected malaria for whom a diagnostic test result for malaria was recorded decreased in arm B (adjusted RR (aRR) = 0.97; 99%CI: 0.82,1.14) during IMID, but increased 25% in arm A (aRR = 1.25; 99%CI:0.94, 1.65) during IMID and OSS relative to baseline; (aRRR = 1.28; 99%CI:0.93, 1.78). The estimated proportion of patients that received an appropriate antimalarial among those prescribed any antimalarial increased in arm B (aRR = 1.09; 99%CI: 0.87, 1.36) and arm A (aRR = 1.50; 99%CI: 1.04, 2.17); (aRRR = 1.38; 99%CI: 0.89, 2.13). The proportion of patients with a negative diagnostic test result for malaria prescribed an antimalarial decreased in arm B (aRR = 0.96; 99%CI: 0.84, 1.10) and arm A (aRR = 0.67; 99%CI: 0.46, 0.97); (aRRR = 0.70; 99%CI: 0.48, 1.00). The proportion of patients with a positive diagnostic test result for malaria prescribed an antibiotic did not change significantly in either arm. The combination of IMID and OSS was associated with statistically significant improvements in malaria case management.

Copper complexes of anionic nitrogen ligands in the amidation and imidation of aryl halides.

PubMed

Tye, Jesse W; Weng, Zhiqiang; Johns, Adam M; Incarvito, Christopher D; Hartwig, John F

2008-07-30

Copper(I) imidate and amidate complexes of chelating N,N-donor ligands, which are proposed intermediates in copper-catalyzed amidations of aryl halides, have been synthesized and characterized by X-ray diffraction and detailed solution-phase methods. In some cases, the complexes adopt neutral, three-coordinate trigonal planar structures in the solid state, but in other cases they adopt an ionic form consisting of an L 2Cu (+) cation and a CuX 2 (-) anion. A tetraalkylammonium salt of the CuX 2 (-) anion in which X = phthalimidate was also isolated. Conductivity measurements and (1)H NMR spectra of mixtures of two complexes all indicate that the complexes exist predominantly in the ionic form in DMSO and DMF solutions. One complex was sufficiently soluble for conductance measurements in less polar solvents and was shown to adopt some degree of the ionic form in THF and predominantly the neutral form in benzene. The complexes containing dative nitrogen ligands reacted with iodoarenes and bromoarenes to form products from C-N coupling, but the ammonium salt of [Cu(phth) 2] (-) did not. Similar selectivities for stoichiometric and catalytic reactions with two different iodoarenes and faster rates for the stoichiometric reactions implied that the isolated amidate and imidate complexes are intermediates in the reactions of amides and imides with haloarenes catalyzed by copper complexes containing dative N,N ligands. These amidates and imidates reacted much more slowly with chloroarenes, including chloroarenes that possess more favorable reduction potentials than some bromoarenes and that are known to undergo fast dissociation of chloride from the chloroarene radical anion. The reaction of o-(allyloxy)iodobenzene with [(phen) 2Cu][Cu(pyrr) 2] results in formation of the C-N coupled product in high yield and no detectable amount of the 3-methyl-2,3-dihydrobenzofuran or 3-methylene-2,3-dihydrobenzofuran products that would be expected from a reaction that generated free radicals. These data and computed reaction barriers argue against mechanisms in which the haloarene reacts with a two-coordinate anionic copper species and mechanisms that start with electron transfer to generate a free iodoarene radical anion. Instead, these data are more consistent with mechanisms involving cleavage of the carbon-halogen bond within the coordination sphere of the metal.

Synthesis and Characterization of Perfluoro Quaternary Ammonium Ion Exchange Membranes for Fuel Cell Applications

DTIC Science & Technology

2012-01-01

complex fuels (2, 4-6). Current research on alkali fuel cells is primarily focused on the development of a solid polymer anion exchange membrane ( AEM ...a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. a...research focus the last few decades due to their high power density and low emissions when operating with hydrogen fuel (1-3). Recently however

Review of Portable, Manually Operated, and Non-Total Flooding Fire Extinguishing Technologies for Use on Naval Vessels

DTIC Science & Technology

2011-12-01

Corrosion problems arising from the use of perfluoro-or hydrofluorocarbon agents have been investigated and are of concern. The concern centers on the...which was formerly known as Powdered Aerosol B, can be used on Class A, Class B, and Class C fires. These agents are a blend of several halocarbons...Canada Review of Portable, Manually Operated, and Non-Total Flooding Fire Extinguishing Technologies for Use on Naval Vessels Contract Project Manager

The Molecular Anatomy of PFDA Hepatotoxicity as Studied by Two-Dimensional Electrophoresis

DTIC Science & Technology

1993-02-26

indicators of cell injury and dysfunction. The compound chosen initially, perfluoro -n-decanoic acid ( PFDA ), is a ten carbon straight-chain perfluorinated ...following: 2mg, 20mg or 50mg PFDA /kg body weight; single injection; animals sacrificed on day 8 of exposure 150mg PFOA /kg ( perfluorooctanoate , PFDA’s...from the following treatments: (I) control; (II) 50mg/kg PFDA ; (III) 100mg/kg PFOA ; and (IV) 400mg/kg clofibrate. Panels V and VI are nitrocellulose

Indolyl aryl sulfones (IASs): development of highly potent NNRTIs active against wt-HIV-1 and clinically relevant drug resistant mutants.

PubMed

Silvestri, Romano; Artico, Marino

2005-01-01

Indolyl aryl sulfones (IASs) are a potent class of NNRTIs developed from L-737,126, a lead agent discovered by Merck AG. IAS derivatives are endowed with inhibitory activities against wt HIV-1 in the low nanomolar concentration range. Introduction of two methyl groups at positions 3 and 5 of the phenyl ring of the aryl sulfonyl moiety furnished IAS derivatives such as 5-chloro- or 5-bromo-3-[(3,5-dimethylphenyl)sulfonyl]indole-2-carboxyamide, which showed very potent and selective anti-HIV-1 activity against some mutants carrying NNRTI resistant mutations at positions 103 and 181 of the reverse transcriptase. IAS derivatives bearing 2-hydroxyethylcarboxyamide or 2-hydroxyethylcarboxyhydrazide groups at position 2 of the indole nucleus were more active than L-737,126 against the K103N-Y181C double mutant. A great improvement of antiviral activity against wt HIV-1 and resistant mutants was obtained by coupling 1-3 simple amino acids, such as glycine and alanine, in sequence, with the 3-[(3,5-dimethylphenyl)sulfonyl]-1H-indole-2-carbonyl moiety. The transformation of the chain terminus into amide or hydrazide, produced short peptides with high selectivity and potent activity against wt HIV-1, and the viral mutants Y181C, K103N-Y181C and EFV(R). IAS having two halogen atoms at the indole showed potent inhibitory activity against the Y181C and the EFV(R) resistant mutant strains. In particular, the introduction of a fluorine atom at position 4 of the indole ring notably contributed to improve the antiviral activities against both wt and the related resistant mutants. 5-Nitro-IASs were highly active against wt HIV-1 and exhibited low cytotoxicity. Experimental data highlighted the class IAS derivatives as promising candidates for clinical trials.

Sulfonyl fluoride-based prosthetic compounds as potential 18F labelling agents.

PubMed

Inkster, James A H; Liu, Kate; Ait-Mohand, Samia; Schaffer, Paul; Guérin, Brigitte; Ruth, Thomas J; Storr, Tim

2012-08-27

Nucleophilic incorporation of [(18)F]F(-) under aqueous conditions holds several advantages in radiopharmaceutical development, especially with the advent of complex biological pharmacophores. Sulfonyl fluorides can be prepared in water at room temperature, yet they have not been assayed as a potential means to (18)F-labelled biomarkers for PET chemistry. We developed a general route to prepare bifunctional 4-formyl-, 3-formyl-, 4-maleimido- and 4-oxylalkynl-arylsulfonyl [(18)F]fluorides from their sulfonyl chloride analogues in 1:1 mixtures of acetonitrile, THF, or tBuOH and Cs[(18)F]F/Cs(2)CO(3(aq.)) in a reaction time of 15 min at room temperature. With the exception of 4-N-maleimide-benzenesulfonyl fluoride (3), pyridine could be used to simplify radiotracer purification by selectively degrading the precursor without significantly affecting observed yields. The addition of pyridine at the start of [(18)F]fluorination (1:1:0.8 tBuOH/Cs(2)CO(3(aq.))/pyridine) did not negatively affect yields of 3-formyl-2,4,6-trimethylbenzenesulfonyl [(18)F]fluoride (2) and dramatically improved the yields of 4-(prop-2-ynyloxy)benzenesulfonyl [(18)F]fluoride (4). The N-arylsulfonyl-4-dimethylaminopyridinium derivative of 4 (14) can be prepared and incorporates (18)F efficiently in solutions of 100 % aqueous Cs(2)CO(3) (10 mg mL(-1)). As proof-of-principle, [(18)F]2 was synthesised in a preparative fashion [88(±8) % decay corrected (n=6) from start-of-synthesis] and used to radioactively label an oxyamino-modified bombesin(6-14) analogue [35(±6) % decay corrected (n=4) from start-of-synthesis]. Total preparation time was 105-109 min from start-of-synthesis. Although the (18)F-peptide exhibited evidence of proteolytic defluorination and modification, our study is the first step in developing an aqueous, room temperature (18)F labelling strategy. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

40 CFR 721.9582 - Certain perfluoroalkyl sulfonates.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-0319306979-40-8 Poly(oxy-1,2-ethanediyl), .alpha.-[2-(methylamino)ethyl]-.omega.-[(1,1,3,3-tetramethylbutyl...]amino]ethyl]-.omega.-hydroxy- 38850-52-1 1-Propanaminium, 3-[(carboxymethyl)[(1,1,2,2,3,3,4,4,5,5,6,6,6...-heptadecafluorooctyl)sulfonyl]methylamino]carbonyl]-.omega.-butoxy- 52166-82-2 1-Propanaminium, N,N,N-trimethyl-3-[[(1...

40 CFR 721.9582 - Certain perfluoroalkyl sulfonates.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-0319306979-40-8 Poly(oxy-1,2-ethanediyl), .alpha.-[2-(methylamino)ethyl]-.omega.-[(1,1,3,3-tetramethylbutyl...]amino]ethyl]-.omega.-hydroxy- 38850-52-1 1-Propanaminium, 3-[(carboxymethyl)[(1,1,2,2,3,3,4,4,5,5,6,6,6...-heptadecafluorooctyl)sulfonyl]methylamino]carbonyl]-.omega.-butoxy- 52166-82-2 1-Propanaminium, N,N,N-trimethyl-3-[[(1...

40 CFR 721.9582 - Certain perfluoroalkyl sulfonates.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-0319306979-40-8 Poly(oxy-1,2-ethanediyl), .alpha.-[2-(methylamino)ethyl]-.omega.-[(1,1,3,3-tetramethylbutyl...]amino]ethyl]-.omega.-hydroxy- 38850-52-1 1-Propanaminium, 3-[(carboxymethyl)[(1,1,2,2,3,3,4,4,5,5,6,6,6...-heptadecafluorooctyl)sulfonyl]methylamino]carbonyl]-.omega.-butoxy- 52166-82-2 1-Propanaminium, N,N,N-trimethyl-3-[[(1...

40 CFR 721.9582 - Certain perfluoroalkyl sulfonates.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-0319306979-40-8 Poly(oxy-1,2-ethanediyl), .alpha.-[2-(methylamino)ethyl]-.omega.-[(1,1,3,3-tetramethylbutyl...]amino]ethyl]-.omega.-hydroxy- 38850-52-1 1-Propanaminium, 3-[(carboxymethyl)[(1,1,2,2,3,3,4,4,5,5,6,6,6...-heptadecafluorooctyl)sulfonyl]methylamino]carbonyl]-.omega.-butoxy- 52166-82-2 1-Propanaminium, N,N,N-trimethyl-3-[[(1...

Environmental Fate and Impacts of Sulfometuron on Watersheds in the Southern United States

Treesearch

J.L. Michael

2003-01-01

Dissipation of sulfometuron (SM), methyl 2-[[[[(4,6-diiethyl-2-pyrimidinyl)amino]carbonyl]amino]sulfonyl] benzoate, in streamflow, sediment, plant tissue, litter, and soil following operational forestry applications at the target rate of 0.42 kg a.i. ha-1 was monitored. Streamflow samples were collected at a weir on the perimeter and 30...

40 CFR 721.10572 - Benzamide, N-[[4- [(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2-methoxy-.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-fitting half-face respirator equipped with N100 (if oil aerosols absent), R100, or P100 filters. (B) NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 (if oil aerosols absent...-purifying respirator equipped with a tight-fitting facepiece (either half-face or full-face) and HEPA...

Reactivity of pyrylium salts toward basic reactants

NASA Technical Reports Server (NTRS)

Neidlein, R.; Witerzens, P.

1981-01-01

The reactivity of some N-acyl and N-sulfonyl-hydrazines 2-4, 10a-10g, 12, 13, 16a, 16b and of hydrazones 18, benzyldihydrazone 21 towards pyrylium salts 1 was examined. By reaction of 2,4,6-trimethyl-pyrylium salt 1 with substituted hydrazines some pyridinium salts were obtained. Relationships between basicity and reactivity were discussed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

McMurray, J. W.; Zhou, Y.; Luo, H. M.

We determined the equilibrium vapor pressures, p e, of the ionic liquid tetraoctylphosphonium bis(2-ethylhexyl)phosphate ([P 8888][DEHP]) over the temperature range 409–495 K using mass loss Knudsen effusion. The p e versus temperature relationship compares well to 1-methyl-3-octylimidazolium bis(trifluoromethylsulfonyl)imide ([C 8mim][NTf 2]) but is lower than that of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C 2mim][NTf 2]) when measured using the same technique. Here, we determined the discrepancies between the p e for [C 8mim][NTf 2] and [C 2mim][NTf 2] with previous studies is discussed. Finally, the enthalpy and entropy of vaporization for all three fluids are estimated from the Clasius-Clapeyron relation.

Method of manufacturing flexible metallic photonic band gap structures, and structures resulting therefrom

DOEpatents

Gupta, Sandhya; Tuttle, Gary L.; Sigalas, Mihail; McCalmont, Jonathan S.; Ho, Kai-Ming

2001-08-14

A method of manufacturing a flexible metallic photonic band gap structure operable in the infrared region, comprises the steps of spinning on a first layer of dielectric on a GaAs substrate, imidizing this first layer of dielectric, forming a first metal pattern on this first layer of dielectric, spinning on and imidizing a second layer of dielectric, and then removing the GaAs substrate. This method results in a flexible metallic photonic band gap structure operable with various filter characteristics in the infrared region. This method may be used to construct multi-layer flexible metallic photonic band gap structures. Metal grid defects and dielectric separation layer thicknesses are adjusted to control filter parameters.

Synthesis and pharmacological properties of new derivatives of 4-alkoxy-6-methyl-1H-pyrrolo[3,4-c]pyridine-1,3(2H)-diones.

PubMed

Sladowska, Helena; Sabiniarz, Aleksandra; Sapa, Jacek; Filipek, Barbara

2009-01-01

Synthesis of 2-(2-hydroxy-3-amino)propyl derivatives of 4-alkoxy-6-methyl-1H-pyrrolo[3,4-c]pyridine-1,3(2H)-diones (24-35) is described. The chlorides used in the above synthesis exist mainly in the cyclic forms (18, 20-23). Only chloride with benzhydryl substituent at the nitrogen atom of piperazine has the chain structure (19). Among the studied imides the most active analgesics in the "writhing" syndrome test proved to be compounds 30 and 31 (with LD50 > 2000 mg/kg) containing 4-benzylpiperidino group. Furthermore, all imides suppressed significantly spontaneous locomotor activity of mice.

Radiofrequency attenuator and method

DOEpatents

Warner, Benjamin P [Los Alamos, NM; McCleskey, T Mark [Los Alamos, NM; Burrell, Anthony K [Los Alamos, NM; Agrawal, Anoop [Tucson, AZ; Hall, Simon B [Palmerston North, NZ

2009-01-20

Radiofrequency attenuator and method. The attenuator includes a pair of transparent windows. A chamber between the windows is filled with molten salt. Preferred molten salts include quarternary ammonium cations and fluorine-containing anions such as tetrafluoroborate (BF.sub.4.sup.-), hexafluorophosphate (PF.sub.6.sup.-), hexafluoroarsenate (AsF.sub.6.sup.-), trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3C.sup.-). Radicals or radical cations may be added to or electrochemically generated in the molten salt to enhance the RF attenuation.

Radiofrequency attenuator and method

DOEpatents

Warner, Benjamin P [Los Alamos, NM; McCleskey, T Mark [Los Alamos, NM; Burrell, Anthony K [Los Alamos, NM; Agrawal, Anoop [Tucson, AZ; Hall, Simon B [Palmerston North, NZ

2009-11-10

Radiofrequency attenuator and method. The attenuator includes a pair of transparent windows. A chamber between the windows is filled with molten salt. Preferred molten salts include quarternary ammonium cations and fluorine-containing anions such as tetrafluoroborate (BF.sub.4.sup.-), hexafluorophosphate (PF.sub.6.sup.-), hexafluoroarsenate (AsF.sub.6.sup.-), trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3 C.sup.-). Radicals or radical cations may be added to or electrochemically generated in the molten salt to enhance the RF attenuation.

Durable electrooptic devices comprising ionic liquids

DOEpatents

Warner, Benjamin P [Los Alamos, NM; McCleskey, T Mark [Los Alamos, NM; Burrell, Anthony K [Los Alamos, NM

2006-10-10

Electrolyte solutions for electrochromic devices such as rear view mirrors and displays with low leakage currents are prepared using inexpensive, low conductivity conductors. Preferred electrolytes include bifunctional redox dyes and molten salt solvents with enhanced stability toward ultraviolet radiation. The solvents include lithium or quaternary ammonium cations, and perfluorinated sulfonylimide anions selected from trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3C.sup.-). Electroluminescent, electrochromic and photoelectrochromic devices with nanostructured electrodes include ionic liquids with bifunctional redox dyes.

Sex-related differences in the enhancing effects of perfluoro-octanoic acid on stearoyl-CoA desaturase and its influence on the acyl composition of phospholipid in rat liver. Comparison with clofibric acid and tiadenol.

PubMed Central

Kawashima, Y; Uy-Yu, N; Kozuka, H

1989-01-01

The effects of the peroxisome proliferators clofibric acid (p-chlorophenoxyisobutyric acid), tiadenol [2,2'-(decamethylenedithio)diethanol] and perfluoro-octanoic acid (PFOA) on hepatic stearoyl-CoA desaturation in male and female rats were compared. Treatment of male rats with the three peroxisome proliferators increased markedly the activity of stearoyl-CoA desaturase. Administration of clofibric acid or tiadenol to female rats increased greatly the hepatic activity of stearoyl-CoA desaturase, the extent of the increases being slightly less pronounced than those of male rats. In contrast with the other two peroxisome proliferators, however, PFOA did not change the activity of stearoyl-CoA desaturase in female rats. Hormonal manipulations revealed that this sex-related difference in the effect of PFOA on stearoyl-CoA desaturase activity is strongly dependent on testosterone. The increase in stearoyl-CoA desaturase activity by peroxisome proliferators was not accompanied by any notable increases in the microsomal content of cytochrome b5 or the activity of NADH: cytochrome b5 reductase. The administration of the peroxisome proliferators greatly altered the acyl composition of hepatic phosphatidylcholine and phosphatidylethanolamine (namely the proportions of C18:1 and C20:3,n-9 fatty acids increased in both phospholipids), and the alterations were partially associated with the increase in stearoyl-CoA desaturase activity. PMID:2574572

A possible role of polycystic ovary syndrome for pregnancy complications in women with psoriasis.

PubMed

De Simone, Clara; Caldarola, Giacomo; Corbeddu, Marialuisa; Moro, Francesca; Tropea, Anna; Moretta, Gaia; Apa, Rosanna

2014-11-01

Psoriasis is a common, chronic, relapsing immune-mediated inflammatory disease (IMID) of the skin. IMIDs are multifactorial diseases characterized by common molecular pathways leading to a systemic inflammation. Patients with an IMID are also at higher risk of developing co-morbidities, such as adverse pregnancy outcomes, than the general population. A higher rate of pregnancy complications have been seen in inflammatory bowel disease and rheumatoid arthritis. The data for psoriasis are inconsistent but it appears that women with moderate-to-severe psoriasis may also have an increased risk of poor pregnancy outcomes. The cause of this association is unknown, although it may be related to elevated proinflammatory cytokines such as IL-6 and TNF-α, the high prevalence of comorbidities and other unhealthy behaviours, or the high prevalence of polycystic ovary syndrome (PCOS). In a recent study, PCOS prevalence in a psoriatic cohort (n = 51) was higher than in non-psoriatic women (n = 102) (47% versus 11%), and women with PCOS and psoriasis had a greater probability of insulin resistance, hyperinsulinaemia, and dyslipidaemia as well as a more severe skin condition, than those with psoriasis alone. Further studies are necessary to clarify the impact of psoriasis on pregnancy and in particular if these effects are mediated by concomitant PCOS. © 2014 Wiley Periodicals, Inc.

The influence of cations on lithium ion coordination and transport in ionic liquid electrolytes: a MD simulation study.

PubMed

Lesch, Volker; Li, Zhe; Bedrov, Dmitry; Borodin, Oleg; Heuer, Andreas

2016-01-07

The dynamical and structural properties in two ionic liquid electrolytes (ILEs) based on 1-ethyl-3-methylimidazolium bis-(trifluoromethanesulfonyl)-imide ([emim][TFSI]) and N-methyl-N-propylpyrrolidinium bis-(trifluoromethanesulfonyl)imide([pyr13][TFSI]) were compared as a function of lithium bis-(trifluoromethanesulfonyl)-imide (LiTFSI) salt concentrations using atomistic molecular dynamics (MD) simulations. The many-body polarizable APPLE&P force field has been utilized. The influence of anion polarization on the structure of the first coordination shell of Li(+) was examined. In particular, the reduction of the oxygen of the TFSI anion (OTFSI) polarizability from 1.36 Å(3) to 1.00 Å(3) resulted in an increased fraction of the TFSI anion bidentate coordination to the Li(+). While the overall dynamics in [pyr13][TFSI]-based ILEs was slower than in [emim][TFSI]-based ILEs, the exchange of TFSI anions in and out of the first coordination shell of Li(+) was found to be faster in pyr13-based systems. The Li(+) ion transference number is higher for these systems as well. These trends can be related to the difference in interaction of TFSI with the IL cation which is stronger for pyr13 than for emim.

Thermometric sensing of nitrofurantoin by noncovalently imprinted polymers containing two complementary functional monomers.

PubMed

Athikomrattanakul, Umporn; Gajovic-Eichelmann, Nenad; Scheller, Frieder W

2011-10-15

Molecularly imprinted polymers (MIPs) for nitrofurantoin (NFT) recognition addressing in parallel of two complementary functional groups were created using a noncovalent imprinting approach. Specific tailor-made functional monomers were synthesized: a diaminopyridine derivative as the receptor for the imide residue and three (thio)urea derivatives for the interaction with the nitro group of NFT. A significantly improved binding of NFT to the new MIPs was revealed from the imprinting factor, efficiency of binding, affinity constants and maximum binding number as compared to previously reported MIPs, which addressed either the imide or the nitro residue. Substances possessing only one functionality (either the imide group or nitro group) showed significantly weaker binding to the new imprinted polymers than NFT. However, the compounds lacking both functionalities binds extremely weak to all imprinted polymers. The new imprinted polymers were applied in a flow-through thermistor in organic solvent for the first time. The MIP-thermistor allows the detection of NFT down to a concentration of 5 μM in acetonitrile + 0.2% dimethyl sulfoxide (DMSO). The imprinting factor of 3.91 at 0.1 mM of NFT as obtained by thermistor measurements is well comparable to the value obtained by batch binding experiments. © 2011 American Chemical Society

Synthesis and optical properties of azo -dye-attached novel second-order NLO polymers with high thermal stability

NASA Astrophysics Data System (ADS)

Ushiwata, Takami; Okamoto, Etsuya; Komatsu, Kyoji; Kaino, Toshikuni

2001-06-01

Novel second order nonlinear optical (NLO) polymethacrylate or polyacrylate polymers with high glass transition temperatures containing an azo dye attached as side-chain have been prepared using a new approach from polymethacrylic acid or polyacrylic acid as starting materials. Glass transition temperatures of 150 approximately 170 degree Celsius were obtained for Disperse red 1 dye attached polymethacrylic acid. These are attributed to the hydrogen bonding between the residual carboxyl groups in the starting polymers. Poled films by corona poling exhibited large NLO susceptibilities, (chi) (2)33 up to 53 pm/V at a wavelength of 1.3 micrometer. Due to the high glass transition temperatures of the polymers, long-term stability of the optical nonlinearity at 100 degrees Celsius was observed for 200 hrs or more. However residual carboxyl groups caused absorbance decrease mainly by hydrolysis of the ester bonds of the polymers investigated by UV-Vis absorption measurement. The stability of induced polar order of the NLO polymer was enhanced by using aminoalkyl chromophore and imidizing it thermally to introduce imide structure into the polymer main-chain. This imidized polymer exhibited (chi) (2)33 of 45 pm/V at a wavelength of 1.3 micrometer and maintained about 90% of the initial value after 230 hrs or more at 100 degrees Celsius.

Anticonvulsants Based on the α-Substituted Amide Group Pharmacophore Bind to and Inhibit Function of Neuronal Nicotinic Acetylcholine Receptors.

PubMed

Krivoshein, Arcadius V

2016-03-16

Although the antiepileptic properties of α-substituted lactams, acetamides, and cyclic imides have been known for over 60 years, the mechanism by which they act remains unclear. I report here that these compounds bind to the nicotinic acetylcholine receptor (nAChR) and inhibit its function. Using transient kinetic measurements with functionally active, nondesensitized receptors, I have discovered that (i) α-substituted lactams and cyclic imides are noncompetitive inhibitors of heteromeric subtypes (such as α4β2 and α3β4) of neuronal nAChRs and (ii) the binding affinity of these compounds toward the nAChR correlates with their potency in preventing maximal electroshock (MES)-induced convulsions in mice. Based on the hypothesis that α-substituted amide group is the essential pharmacophore of these drugs, I found and tested a simple compound, 2-phenylbutyramide. This compound indeed inhibits nAChR and shows good anticonvulsant activity in mice. Molecular docking simulations suggest that α-substituted lactams, acetamides, and cyclic imides bind to the same sites on the extracellular domain of the receptor. These new findings indicate that inhibition of brain nAChRs may play an important role in the action of these antiepileptic drugs, a role that has not been previously recognized.

Wholly Aromatic Ether-Imides as n-Type Semiconductors

NASA Technical Reports Server (NTRS)

Weiser, Erik; St. Clair, Terry L.; Dingemans, Theo J.; Samulski, Edward T.; Irene, Gene

2006-01-01

Some wholly aromatic ether-imides consisting of rod-shaped, relatively-low-mass molecules that can form liquid crystals have been investigated for potential utility as electron-donor-type (ntype) organic semiconductors. It is envisioned that after further research to improve understanding of their physical and chemical properties, compounds of this type would be used to make thin film semiconductor devices (e.g., photovoltaic cells and field-effect transistors) on flexible electronic-circuit substrates. This investigation was inspired by several prior developments: Poly(ether-imides) [PEIs] are a class of engineering plastics that have been used extensively in the form of films in a variety of electronic applications, including insulating layers, circuit boards, and low-permittivity coatings. Wholly aromatic PEIs containing naphthalene and perylene moieties have been shown to be useful as electrochromic polymers. More recently, low-molecular-weight imides comprising naphthalene-based molecules with terminal fluorinated tails were shown to be useful as n-type organic semiconductors in such devices as field-effect transistors and Schottky diodes. Poly(etherimide)s as structural resins have been extensively investigated at NASA Langley Research Center for over 30 years. More recently, the need for multi-functional materials has become increasingly important. This n-type semiconductor illustrates the scope of current work towards new families of PEIs that not only can be used as structural resins for carbon-fiber reinforced composites, but also can function as sensors. Such a multi-functional material would permit so-called in-situ health monitoring of composite structures during service. The work presented here demonstrates that parts of the PEI backbone can be used as an n-type semiconductor with such materials being sensitive to damage, temperature, stress, and pressure. In the near future, multi-functional or "smart" composite structures are envisioned to be able to communicate such important parameters to the flight crew and provide vital information with respect to the operational status of their aircraft.

Novel therapies for immune-mediated inflammatory diseases: What can we learn from their use in rheumatoid arthritis, spondyloarthritis, systemic lupus erythematosus, psoriasis, Crohn's disease and ulcerative colitis?

PubMed

Baker, Kenneth F; Isaacs, John D

2018-02-01

The past three decades have witnessed remarkable advances in our ability to target specific elements of the immune and inflammatory response, fuelled by advances in both biotechnology and disease knowledge. As well as providing superior treatments for immune-mediated inflammatory diseases (IMIDs), such therapies also offer unrivalled opportunities to study the underlying immunopathological basis of these conditions.In this review, we explore recent approaches to the treatment of IMIDs and the insights to pathobiology that they provide. We review novel biologic agents targeting the T-helper 17 axis, including therapies directed towards interleukin (IL)-17 (secukinumab, ixekizumab, bimekizumab), IL-17R (brodalumab), IL-12/23p40 (ustekinumab, briakinumab) and IL-23p19 (guselkumab, tildrakizumab, brazikumab, risankizumab, mirikizumab). We also present an overview of biologics active against type I and II interferons, including sifalumumab, rontalizumab, anifrolumab and fontolizumab. Emerging strategies to interfere with cellular adhesion processes involved in lymphocyte recruitment are discussed, including both integrin blockade (natalizumab, vedolizumab, etrolizumab) and sphingosine-1-phosphate receptor inhibition (fingolimod, ozanimod). We summarise the development and recent application of Janus kinase (JAK) inhibitors in the treatment of IMIDs, including first-generation pan-JAK inhibitors (tofacitinib, baricitinib, ruxolitinib, peficitinib) and second-generation selective JAK inhibitors (decernotinib, filgotinib, upadacitinib). New biologics targeting B-cells (including ocrelizumab, veltuzumab, tabalumab and atacicept) and the development of novel strategies for regulatory T-cell modulation (including low-dose IL-2 therapy and Tregitopes) are also discussed. Finally, we explore recent biotechnological advances such as the development of bispecific antibodies (ABT-122, COVA322), and their application to the treatment of IMIDs. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Fluorinated arene, imide and unsaturated pyrrolidinone based donor acceptor conjugated polymers: Synthesis, structure-property and device studies

NASA Astrophysics Data System (ADS)

Liyanage, Arawwawala Don Thilanga

After the discovery of doped polyacetylene, organic semiconductor materials are widely studied as high impending active components in consumer electronics. They have received substantial consideration due to their potential for structural tailoring, low cost, large area and mechanically flexible alternatives to common inorganic semiconductors. To acquire maximum use of these materials, it is essential to get a strong idea about their chemical and physical nature. Material chemist has an enormous role to play in this novel area, including development of efficient synthetic methodologies and control the molecular self-assembly and (opto)-electronic properties. The body of this thesis mainly focuses on the substituent effects: how different substituents affect the (opto)-electronic properties of the donor-acceptor (D-A) conjugated polymers. The main priority goes to understand, how different alkyl substituent effect to the polymer solubility, crystallinity, thermal properties (e.g.: glass transition temperature) and morphological order. Three classes of D-A systems were extensively studied in this work. The second chapter mainly focuses on the synthesis and structure-property study of fluorinated arene (TFB) base polymers. Here we used commercially available 1,4-dibromo-2,3,5,6-tetrafluorobenzene (TFB) as the acceptor material and prepare several polymers using 3,3'-dialkyl(3,3'-R2T2) or 3,3'-dialkoxy bithiophene (3,3'-RO2T2) units as electron donors. A detail study was done using 3,3'-bithiophene donor units incorporating branched alkoxy-functionalities by systematic variation of branching position and chain length. The study allowed disentangling the branching effects on (i) aggregation tendency, intermolecular arrangement, (iii) solid state optical energy gaps, and (iv) electronic properties in an overall consistent picture, which might guide future polymer synthesis towards optimized materials for opto-electronic applications. The third chapter mainly focused on the structure-property study of imide functionalized D-A polymers. Here we used thiophene-imide (TPD) as the acceptor moiety and prepare several D-A polymers by varying the donor units. When selecting the donor units, more priority goes to the fused ring systems. One main reason to use imide functionality is due to the, open position of the imide nitrogen, which provides an attaching position to alkyl substituent. Through this we can easily manipulate solubility and solid state packing arrangement. Also these imide acceptors have low-lying LUMOs due to their electron deficient nature and this will allow tuning the optical energy gap by careful choice of donor materials with different electron donating ability. The fourth chapter mainly contribute to the synthesis and structure property study of a completely novel electron acceptor moiety consist of a unsaturated pyrrolidinone unit known as Pechmann dye (PD) core. Pechmann dyes are closely related to the Indigo family. This can refer as 3-butenolide dimer connected via an alkene bridge, containing a benzene ring at the 5 and 5' positions of the lactone rings. We have prepared several D-A polymers using this PD system with benzodithiophene (BDT) as the donor unit. Different to common D-A polymers the HOMO and LUMO of the PD acceptor moiety are energetically located within the gap of the BDT, so that the electronic and optical properties (HOMO-LUMO transition) are dictated by the PD properties. The promising electronic properties, band gaps, high absorption coefficients and broad absorption suggest this new D-A polymers as an interesting donor material for organic solar cell (OSC) applications. KEY WORDS: Organic semiconductor materials, Self assembly, (opto)-electronic properties, Donor-Acceptor conjugated polymers, Fluorinated arene, 3,3'-bithiophene donors, Thiophene-imide (TPD), Pechmann dye, benzodithiophene, organic solar cell.

21 CFR 73.3121 - Poly(hydroxyethyl methacrylate)-dye copolymers.

Code of Federal Regulations, 2011 CFR

2011-04-01

...-naphthalenedisulfonic acid, 4-amino-5-hydroxy-3,6-bis((4-((2-(sulfooxy)ethyl)sulfonyl)phenyl)azo)-tetrasodium salt] (CAS...)-] (CAS Reg. No. 60958-41-0); (5) Reactive Blue No. 19 [2-anthracene-sulfonic acid, 1-amino-9,10-dihydro-9...); (6) Reactive Blue No. 4 [2-anthracenesulfonic acid, 1-amino-4-(3-((4,6-dichloro-s-triazin-2-yl)amino...

21 CFR 73.3121 - Poly(hydroxyethyl methacrylate)-dye copolymers.

Code of Federal Regulations, 2010 CFR

2010-04-01

...-naphthalenedisulfonic acid, 4-amino-5-hydroxy-3,6-bis((4-((2-(sulfooxy)ethyl)sulfonyl)phenyl)azo)-tetrasodium salt] (CAS...)-] (CAS Reg. No. 60958-41-0); (5) Reactive Blue No. 19 [2-anthracene-sulfonic acid, 1-amino-9,10-dihydro-9...); (6) Reactive Blue No. 4 [2-anthracenesulfonic acid, 1-amino-4-(3-((4,6-dichloro-s-triazin-2-yl)amino...

Direct Functionalization of Kevlar (registered trademark) with Copolymers Containing Sulfonyl Nitrene

DTIC Science & Technology

2016-01-01

phenylene terephthalamide) (Kevlar®) fibers via thermal generation of an electrophilic nitrene, while preserving the mechanical properties of the...poly(p-phenylene terephthalamide) (Kevlar®) fibers via thermal generation of an electrophilic nitrene, while preserving the mechanical properties of...radiation, plasma, or chemical radical generation,12 conventional solution-based electrophilic aromatic substitution,13 silanation,14 or hydrolysis with

Effect of viscosity on steady-state voltammetry and scanning electrochemical microscopy in room temperature ionic liquids.

PubMed

Lovelock, Kevin R J; Cowling, Frances N; Taylor, Alasdair W; Licence, Peter; Walsh, Darren A

2010-04-08

The electrochemical properties of a series of room temperature ionic liquids (RTILs) were studied using voltammetric methods and scanning electrochemical microscopy (SECM). The RTILs consisted of 1-alkyl-3-methylimidazolium cations, [C(n)C(1)Im](+), and either bis[(trifluoromethyl)sulfonyl]imide anions, [Tf(2)N](-), or hexafluorophosphate anions, [PF(6)](-). The effect of RTIL viscosity on mass transfer dynamics within each RTIL was studied electrochemically using ferrocene as a redox probe. In the case of the [C(n)C(1)Im][Tf(2)N] RTILs, the viscosity was altered by changing the alkyl chain length. [C(4)C(1)Im][PF(6)] was used for comparison as its viscosity is significantly higher than that of the [C(n)C(1)Im][Tf(2)N] RTILs. The RTIL viscosity affected the ability to record steady-state voltammograms at ultramicroelectrodes (UMEs). For example, it was possible to record steady-state voltammograms at scan rates up to 10 mV s(-1) in [C(2)C(1)Im][Tf(2)N] using 1.5 mum radius disk UMEs, but non-steady-state behavior was observed at 50 mV s(-1). However, at 12.5 microm radius UMEs, steady-state voltammetry was only observed at 1 mV s(-1) in [C(2)C(1)Im][Tf(2)N]. The RTIL viscosity also affected the ability to record SECM feedback approach curves that agreed with conventional SECM theory. In the most viscous [C(n)C(1)Im][Tf(2)N] RTILs, feedback approach curves agreed with conventional theory only when very slow tip approach speeds were used (0.1 microm s(-1)). These observations were interpreted using the Peclet number, which describes the relative contributions of convective and diffusive mass transfer to the tip surface. By recording feedback approach curves in each RTIL at a range of tip approach speeds, we describe the experimental conditions that must be met to perform SECM in imidazolium-based RTILs. The rate of heterogeneous electron transfer across the RTIL/electrode interface was also studied using SECM and the standard heterogeneous electron transfer rate constant, k(0), for ferrocene oxidation recorded in each RTIL was higher than that determined previously using voltammetric methods.

Protozoan Parasite Growth Inhibitors Discovered by Cross-Screening Yield Potent Scaffolds for Lead Discovery

PubMed Central

2015-01-01

Tropical protozoal infections are a significant cause of morbidity and mortality worldwide; four in particular (human African trypanosomiasis (HAT), Chagas disease, cutaneous leishmaniasis, and malaria) have an estimated combined burden of over 87 million disability-adjusted life years. New drugs are needed for each of these diseases. Building on the previous identification of NEU-617 (1) as a potent and nontoxic inhibitor of proliferation for the HAT pathogen (Trypanosoma brucei), we have now tested this class of analogs against other protozoal species: T. cruzi (Chagas disease), Leishmania major (cutaneous leishmaniasis), and Plasmodium falciparum (malaria). Based on hits identified in this screening campaign, we describe the preparation of several replacements for the quinazoline scaffold and report these inhibitors’ biological activities against these parasites. In doing this, we have identified several potent proliferation inhibitors for each pathogen, such as 4-((3-chloro-4-((3-fluorobenzyl)oxy)phenyl)amino)-6-(4-((4-methyl-1,4-diazepan-1-yl)sulfonyl)phenyl)quinoline-3-carbonitrile (NEU-924, 83) for T. cruzi and N-(3-chloro-4-((3-fluorobenzyl)oxy)phenyl)-7-(4-((4-methyl-1,4-diazepan-1-yl)sulfonyl)phenyl)cinnolin-4-amine (NEU-1017, 68) for L. major and P. falciparum. PMID:26087257

Sulfonyl 3-alkynyl pantetheinamides as mechanism-based crosslinkers of ACP dehydratase

PubMed Central

Ishikawa, Fumihiro; Haushalter, Robert W.; Lee, D. John; Finzel, Kara; Burkart, Michael D.

2013-01-01

The acyl carrier protein (ACP) plays a central function in acetate biosynthetic pathways, serving as a tether for substrates and growing intermediates. Activity and structural studies have highlighted the complexities of this role, and its protein-protein interactions have recently come under scrutiny as a regulator of catalysis. As existing methods to interrogate these interactions have fallen short, we have sought to develop new tools to aid their study. Here we describe the design, synthesis, and application of pantetheinamides capable of crosslinking ACPs with catalytic β-hydroxyacyl carrier protein dehydratase (DH) domains based upon a 3-alkynyl sulfone warhead. We demonstrate this process by application to the Escherichia coli fatty acid synthase and apply it to probe protein-protein interactions with non-cognate carrier proteins. Finally, we use solution phase protein NMR to demonstrate that sulfonyl-3-alkynyl pantetheinamide is fully sequestered by the ACP, indicating that the crypto-ACP closely mimics the natural DH substrate. This crosslinking technology offers immediate potential to lock these biosynthetic enzymes in their native binding states by providing access to mechanistically-crosslinked enzyme complexes, presenting a solution to ongoing structural challenges. PMID:23718183

Exchange Reactions of Organotin and Organosilicon Compounds with Mild Fluorinating Agents

DTIC Science & Technology

1992-03-01

methylphosphonic difluoride, boron trifluoride etherate, and perfluoroisobutene all react with both organosilicon and organotin. alkoxides to give...inlet tube, was charged with tributyltin cyanide (53.30 gm, 0.1686 mol) in a dry glove bag under an inert atmosphere and 500 ml of dry xylene was then...Chem. Vol. 29, p 471 (1985). 6. Tyuleneva, V.V., Rozov, L.A., Zeifman, Yu.V. and I. L. Knuny- ants,"Exchange of Fluorine by Chlorine in Perfluoro-isobutene," Tzv.Akad.Nauk. SSSR. Ser. Khim No. 5, p 1136 (1975). 17

Vaporization behavior of tetraoctylphosphonium bis(2-ethylhexyl)phosphate ionic liquid

DOE PAGES

McMurray, J. W.; Zhou, Y.; Luo, H. M.; ...

2016-11-18

We determined the equilibrium vapor pressures, p e, of the ionic liquid tetraoctylphosphonium bis(2-ethylhexyl)phosphate ([P 8888][DEHP]) over the temperature range 409–495 K using mass loss Knudsen effusion. The p e versus temperature relationship compares well to 1-methyl-3-octylimidazolium bis(trifluoromethylsulfonyl)imide ([C 8mim][NTf 2]) but is lower than that of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C 2mim][NTf 2]) when measured using the same technique. Here, we determined the discrepancies between the p e for [C 8mim][NTf 2] and [C 2mim][NTf 2] with previous studies is discussed. Finally, the enthalpy and entropy of vaporization for all three fluids are estimated from the Clasius-Clapeyron relation.

Vaporization behavior of tetraoctylphosphonium bis(2-ethylhexyl)phosphate ionic liquid

NASA Astrophysics Data System (ADS)

McMurray, J. W.; Zhou, Y.; Luo, H. M.; Qu, J.

2017-01-01

The equilibrium vapor pressures, pe, of the ionic liquid tetraoctylphosphonium bis(2-ethylhexyl)phosphate ([P8888][DEHP]) over the temperature range 409-495 K were determined for the first time using mass loss Knudsen effusion. The pe versus temperature relationship compares well to 1-methyl-3-octylimidazolium bis(trifluoromethylsulfonyl)imide ([C8mim][NTf2]) but is lower than that of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C2mim][NTf2]) when measured using the same technique. The discrepancies between the pe determined in this work for [C8mim][NTf2] and [C2mim][NTf2] with previous studies is discussed. The enthalpy and entropy of vaporization for all three fluids are estimated from the Clasius-Clapeyron relation.

Reversible electro-optic device employing aprotic molten salts and method

DOEpatents

Warner, Benjamin P [Los Alamos, NM; McCleskey, T Mark [Los Alamos, NM; Burrell, Anthony K [Los Alamos, NM; Hall, Simon B [Palmerston North, NZ

2008-01-08

A single-compartment reversible mirror device having a solution of aprotic molten salt, at least one soluble metal-containing species comprising metal capable of being electrodeposited, and at least one anodic compound capable of being oxidized was prepared. The aprotic molten salt is liquid at room temperature and includes lithium and/or quaternary ammonium cations, and anions selected from trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3C.sup.-). A method for preparing substantially pure molten salts is also described.

Reversible Electro-Optic Device Employing Aprotic Molten Salts And Method

DOEpatents

Warner, Benjamin P.; McCleskey, T. Mark; Burrell, Anthony K.; Hall, Simon B.

2005-03-01

A single-compartment reversible mirror device having a solution of aprotic molten salt, at least one soluble metal-containing species comprising metal capable of being electrodeposited, and at least one anodic compound capable of being oxidized was prepared. The aprotic molten salt is liquid at room temperature and includes lithium and/or quaternary ammonium cations, and anions selected from trifluoromethylsulfonate (CF.sub.3 SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3 SO.sub.2).sub.2 N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3 CF.sub.2 SO.sub.2).sub.2 N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3 SO.sub.2).sub.3 C.sup.-). A method for preparing substantially pure molten salts is also described.

Synthesis and Characterization of Modified Phenylethynyl Terminated Polyimides

NASA Technical Reports Server (NTRS)

Chang, Alice C.

1998-01-01

As an ongoing effort to develop structural adhesives for high performance aerospace applications, recent work has focused on phenylethynyl terminated imide (PETI) oligomers. The work reported herein involves the synthesis and characterization of a series of phenylethynyl containing oligomers designated LARC (TM) MPEI (Modified Phenylethynyl Terminated Polyimide). These oligomers contain mixtures of linear, branched and star-shaped molecules. The fully imidized polymers exhibited minimum melt viscosity as low as 600 poise at 335 C. Ti/Ti lap shear specimens processed at 288 C under 15 psi showed tensile shear strength of approx. 6000 psi and 5200 psi at ambient and 350 F temperatures, respectively. The chemistry and properties of these new MPEIs are presented and compared to an optimized linear PETI, LaRC(Tm) -PETI-5.

Structure, conformations, vibrations, and ideal-gas properties of 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ionic pairs and constituent ions.

PubMed

Paulechka, Yauheni U; Kabo, Gennady J; Emel'yanenko, Vladimir N

2008-12-11

Energies, geometries, and frequencies of normal vibrations have been calculated by quantum-chemical methods for different conformers of a bis(trifluoromethylsulfonyl)imide anion (NTf2-), 1-alkyl-3-methylimidazolium cations ([C(n)mim]+, n = 2, 4, 6, 8), and [C(n)mim]NTf2 ionic pairs. The assignment of frequencies for NTf2-, [C2mim]+, and [C4mim]+ in the vibrational spectra of ionic liquids have been performed. Thermodynamic properties of [C(n)mim]NTf2, [C(n)mim]+, and NTf2- in the gas state have been calculated by the statistical thermodynamic methods. The resulting entropies are in satisfactory agreement with the values obtained from the experimental data previously reported in literature.

Effect of Hydration on the Mechanical Properties of Anion Exchange Membranes

DTIC Science & Technology

2015-01-19

trimethylbenzyl ammonium (PFTMBA), c.) ethyl ammonium (PFEA). ...............26! Figure 3.3: a.) Full IR spectra of the 3M sulfonyl precursor, methyl...with the cation group. ............................................................................................30! Figure 3.4: IR spectra of all...is modified from a paper published in Journal of Polymer Science, Part B: Polymer Physics1 Melissa A. Vandiver2, James L. Horan3, Yuan Yang4, Emily T

Effect of Sulfometuron Methyl on Ground Water and Stream Quality in Coastal Plain Forest Watersheds

Treesearch

D.G. Neary; J.L. Michael

1989-01-01

Sulfometuron methyl [methyl 2-[[[[(4,6-dimethyl-2-pyrimidinyl)a-mino]carbonyl]amino]sulfonyl]benzoate] was applied by a ground sprayer at a maximum labeled rate of 0.42 kg ha-1 a.i. to a 4 ha Coastal Plain flatwoods watershed BS site preperation for tree planting. Herbicide residues were detected in streamflow for only seven days after...

Impact of Alkyl Spacer Length on Aggregation Pathways in Kinetically Controlled Supramolecular Polymerization.

PubMed

Ogi, Soichiro; Stepanenko, Vladimir; Thein, Johannes; Würthner, Frank

2016-01-20

We have investigated the kinetic and thermodynamic supramolecular polymerizations of a series of amide-functionalized perylene bisimide (PBI) organogelator molecules bearing alkyl spacers of varied lengths (ethylene to pentylene chains, PBI-1-C2 to PBI-1-C5) between the amide and PBI imide groups. These amide-functionalized PBIs form one-dimensional fibrous nanostructures as the thermodynamically favored states in solvents of low polarity. Our in-depth studies revealed, however, that the kinetic behavior of their supramolecular polymerization is dependent on the spacer length. Propylene- and pentylene-tethered PBIs follow a similar polymerization process as previously observed for the ethylene-tethered PBI. Thus, the monomers of these PBIs are kinetically trapped in conformationally restricted states through intramolecular hydrogen bonding between the amide and imide groups. In contrast, the intramolecularly hydrogen-bonded monomers of butylene-tethered PBI spontaneously self-assemble into nanoparticles, which constitute an off-pathway aggregate state with regard to the thermodynamically stable fibrous supramolecular polymers obtained. Thus, for this class of π-conjugated system, an unprecedented off-pathway aggregate with high kinetic stability could be realized for the first time by introducing an alkyl linker of optimum length (C4 chain) between the amide and imide groups. Our current system with an energy landscape of two competing nucleated aggregation pathways is applicable to the kinetic control over the supramolecular polymerization by the seeding approach.

Solvent and substituent effects on aggregation constants of perylene bisimide π-stacks--a linear free energy relationship analysis.

PubMed

Chen, Zhijian; Fimmel, Benjamin; Würthner, Frank

2012-08-14

A series of six perylene bisimides (PBIs) with hydrophilic and hydrophobic side chains at the imide nitrogens were applied for a comparative study of the solvent and structural effects on the aggregation behaviour of this class of dyes. A comparison of the binding constants in tetrachloromethane at room temperature revealed the highest binding constant of about 10(5) M(-1) for a PBI bearing 3,4,5-tridodecyloxyphenyl substituents at the imide nitrogens, followed by 3,4,5-tridodecylphenyl and alkyl-substituted PBIs, whereas no aggregation could be observed in the accessible concentration range for PBIs equipped with bulky 2,6-diisopropylphenyl substituents at the imide nitrogens. The aggregation behaviour of three properly soluble compounds was investigated in 17 different solvents covering a broad polarity range from nonpolar n-hexane to highly polar DMSO and water. Linear free energy relationships (LFER) revealed a biphasic behaviour between Gibbs free energies of aggregation and common empirical solvent polarity scales indicating particularly strong π-π stacking interactions in nonpolar aliphatic and polar alcoholic solvents whilst the weakest binding is observed in dichloromethane and chloroform. Accordingly, PBI aggregation is dominated by electrostatic interactions in nonpolar solvents and by solvophobic interactions in protic solvents. In water, the aggregation constant is increased far beyond LFER expectations pointing at a pronounced hydrophobic effect.

Effects of Imide-Orthoborate Dual-Salt Mixtures in Organic Carbonate Electrolytes on the Stability of Lithium Metal Batteries.

PubMed

Li, Xing; Zheng, Jianming; Engelhard, Mark H; Mei, Donghai; Li, Qiuyan; Jiao, Shuhong; Liu, Ning; Zhao, Wengao; Zhang, Ji-Guang; Xu, Wu

2018-01-24

The effects of lithium imide and lithium orthoborate dual-salt electrolytes of different salt chemistries in carbonate solvents on the cycling stability of lithium (Li) metal batteries are systematically and comparatively investigated. Two imide salts (LiTFSI and LiFSI) and two orthoborate salts (LiBOB and LiDFOB) are chosen for this study and compared with the conventional LiPF 6 salt. Density functional theory calculations indicate that the chemical and electrochemical stabilities rank in the following order: LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiDFOB > LiFSI-LiBOB. The experimental cycling stability of the Li metal batteries with the electrolytes ranks in the following order: LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiDFOB > LiPF 6 > LiFSI-LiBOB, which is in well accordance with the calculation results. The LiTFSI-LiBOB can effectively protect the Al substrate and form a more robust surface film on Li metal anode, while the LiFSI-LiBOB results in serious corrosion to the stainless steel cell case and a thicker and looser surface film on Li anode. The key findings of this work emphasize that the salt chemistry is critically important for enhancing the interfacial stability of Li metal anode and should be carefully manipulated in the development of high-performance Li metal batteries.

Comprehensive Insights into the Reactivity of Electrolytes Based on Sodium Ions.

PubMed

Eshetu, Gebrekidan Gebresilassie; Grugeon, Sylvie; Kim, Huikyong; Jeong, Sangsik; Wu, Liming; Gachot, Gregory; Laruelle, Stephane; Armand, Michel; Passerini, Stefano

2016-03-08

We report a systematic investigation of Na-based electrolytes that comprise various NaX [X=hexafluorophosphate (PF6 ), perchlorate (ClO4 ), bis(trifluoromethanesulfonyl)imide (TFSI), fluorosulfonyl-(trifluoromethanesulfonyl)imide (FTFSI), and bis(fluorosulfonyl)imide (FSI)] salts and solvent mixtures [ethylene carbonate (EC)/dimethyl carbonate (DMC), EC/diethyl carbonate (DEC), and EC/propylene carbonate (PC)] with respect to the Al current collector stability, formation of soluble degradation compounds, reactivity towards sodiated hard carbon (Nax -HC), and solid-electrolyte interphase (SEI) layer formation. Cyclic voltammetry demonstrates that the stability of Al is highly influenced by the nature of the anions, solvents, and additives. GC-MS analysis reveals that the formation of SEI telltales depends on the nature of the linear alkyl carbonates and the battery chemistry (Li(+) vs. Na(+) ). FTIR spectroscopy shows that double alkyl carbonates are the main components of the SEI layer on Nax -HC. In the presence of Na salts, EC/DMC and EC/DEC presented a higher reactivity towards Nax -HC than EC/PC. For a fixed solvent mixture, the onset temperature follows the sequence NaClO4

Risk of Progression and Survival in Multiple Myeloma Relapsing After Therapy with IMiDs and Bortezomib: A Multicenter International Myeloma Working Group Study

PubMed Central

Kumar, Shaji; Lee, Jae Hoon; Lahuerta, Juan J.; Morgan, Gareth; Richardson, Paul G.; Crowley, John; Haessler, Jeff; Feather, John; Hoering, Antje; Moreau, Philippe; LeLeu, Xavier; Hullin, Cyrille; Klein, Saskia K.; Sonneveld, Pieter; Siegel, David; Bladé, Joan; Goldschmidt, Hartmut; Jagannath, Sundar; San Miguel, Jesus; Orlowski, Robert; Palumbo, Antonio; Sezer, Orhan; Durie, Brian G.M.

2014-01-01

Promising new drugs are being evaluated for treatment of multiple myeloma (MM), but their impact should be measured against the expected outcome in patients failing current therapies. However, the natural history of relapsed disease in the current era remains unclear. We studied 286 patients with relapsed MM, who were refractory to bortezomib and were relapsed, refractory, or ineligible, to an IMiD (Immunomodulatory Drug), with measurable disease and ECOG PS of 0, 1 or 2. The date patients satisfied the entry criteria was defined as time zero (T0). The median age at diagnosis was 58 years and time from diagnosis to T0 was 3.3 years. Following T0, 213 (74%) patients had a treatment recorded with one or more regimens (median=1; range 0-8). The first regimen contained bortezomib in 55 (26%) patients and an IMiD in 70 (33%). A minor response or better was seen to at least one therapy after T0 in 94 patients (51%) including >=partial response in 69 (38%). The median overall survival and event free survival from T0 were 9 and 5 months respectively. This study confirms the poor outcome once patients become refractory to current treatments. The results provide context for interpreting ongoing trials of new drugs. PMID:21799510

Hexafluorobenzene in comparison with perfluoro-15-crown-5-ether for repeated monitoring of oxygenation using 19F MRI in a mouse model.

PubMed

Mignion, Lionel; Magat, Julie; Schakman, Olivier; Marbaix, Etienne; Gallez, Bernard; Jordan, Bénédicte F

2013-01-01

Hexafluorobenzene (HFB) and perfluoro-15-crown-5-ether (15C5) were compared as fluorine reporter probes of tissue oxygenation using (19)F MRI for dynamic assessment of muscle oxygenation, with special focus on muscle tissue toxicity of the probes, and consecutive alteration of animal behavior. The latter were also compared in terms of sensitivity to changes in oxygenation as well as of signal-to-noise ratio for accurate pO(2) measurements. For that purpose, mouse muscles were imaged at 11.7 T, at 2- and 36-h after intramuscular injection of HFB or 15C5. Histological analysis of the muscle tissue revealed a lack of toxicity for 15C5 from 2 up to 36-h postinjection, whereas HFB induced tissue necrosis, blood clots and thrombosis as soon as 24-h postinjection. This muscle toxicity led to a limitation in mice mobility 24-h after injection of HFB as evidenced by behavioral testing (open-field, grip strength, and catwalk tests), which was not the case after 15C5 intramuscular injection. Finally, pO(2) measurements assessed 2-h postinjection showed consistent values with both probes, evidencing cross-validation of the (19)F MRI oximetry technique for acute measurements. However, the measurement at 36-h was hampered for HFB, which showed significant lower values of muscle pO(2), whereas 15C5 was able to reliably assess muscle pO(2) at 36-h postinjection. Copyright © 2012 Wiley Periodicals, Inc.

Enhanced organic memory devices (OMEM) with a photochromic perhydro DTE as a transduction layer (Conference Presentation)

NASA Astrophysics Data System (ADS)

Cordes, Sandra; Kranz, Darius; Maibach, Eduard; Kempf, Maxim; Meerholz, Klaus

2016-09-01

In modern electronic systems memory elements are of fundamental importance for data storage. Especially solution-processable nonvolatile organic memories, which are inexpensive and can be manufactured on flexible substrates, are a promising alternative to brittle inorganic devices. Organic photochromic switchable compounds, mostly dithienylethenes (DTEs), are thermally stable, fatigue resistant and can undergo an electrically- or/and photo-induced ring-opening and -closing reaction which results in a change of energy levels. Due to the energetic difference in the highest occupied molecular orbital (HOMO) between the open and closed isomer, the DTE layer can be exploited as a switchable hole injection barrier that controls the electrical current in the diode. We demonstrated that a light-emitting organic memory (LE-OMEM) device with a perfluoro DTE transduction layer can be switched electrically via high current densities pulses and optically by irradiated light, with impressive current ON/OFF Ratios (OOR) of 10Λ2, 10Λ4 respectively. Currently we aim to minimize the barrier of the ON state and maximize the barrier of the OFF state by designing DTE molecules with larger differences in the HOMO energies of the two isomers yielding improved OOR values. By synthesizing perhydro derivates of DTE we achieved molecules with high HOMO levels and large ΔHOMO energies providing OMEM devices with excellent physical properties (OOR 1.4 x higher than perfluoro DTE). Due to the high HOMO level of the perhydro DTE utilization of hole transport layers (HTLs) is not necessary and thus manufacturing of OMEM devices is simplified.

Adhesive and Composite Properties of a New Phenylethynyl Terminated Imide

NASA Technical Reports Server (NTRS)

Thompson, C. M.; Connell, J. W.; Hergenrother, P. M.

2002-01-01

A relatively new phenylethynyl terminated imide oligomer (PETI) from the reaction of 2,3,',4'- biphenyltetracarboxylic dianhydride, 4,4'-oxydianiline and endcapped with 4- phenylethynylphthalic anhydride at a calculated number average molecular weight of 5000 g/mole was evaluated as an adhesive and composite matrix. The asymmetric dianhydride imparts a low melt viscosity to the oligomer and a high glass transition temperature to the cured resin. Preliminary adhesive work with titanium (6Al-4V) adherend gave good room temperature (RT) tensile shear strengths and excellent retention of RT strength at 260 C. Preliminary composite work using unsized IM7 carbon fiber provided moderate to high mechanical properties. The chemistry, mechanical, and physical properties of the new PETI in neat resin, adhesive and composite form are presented.

Influence of excess diamine on properties of PMR polyimide resins and composites

NASA Technical Reports Server (NTRS)

Hurwitz, F. I.

1980-01-01

By varying the stoichiometry of the reactants in the preparation of PMR polyimide resin, changes occur in molecular weight distribution which influence the rheological properties and thus the processability of the resin, as well as the mechanical properties of the composite. The influence of 1-10 percent molar excess MDA on the molecular weight distribution and rheological properties of an imidized PMR system were exposed. Molecular weight distribution is characterized by gel permeation chromatography of the imidized molding compound; shear viscosity is related to changes in average molecular weight. The thermo-oxidative stability at 600 F, glass transition temperature, flexural and interlaminar shear properties of PMR polyimide/Celion 6000 graphite fiber composites are compared as a function of the percent excess MDA in the monomer reactant mixture.

Aging Effects on the Properties of Imidazolium-, Quaternary Ammonium-, Pyridinium-, and Pyrrolidinium-Based Ionic Liquids Used in Fuel and Energy Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, Elise B.; Smith, L. Taylor; Williamson, Tyler K.

2013-11-21

Ionic liquids (ILs) are often cited for their excellent thermal stability, a key property for their use as solvents and in the chemical processing of biofuels. However, there has been little supporting data on the long-term aging effect of the temperature on these materials. Imizadolium-, quaternary ammonium-, pyridinium-, and pyrrolidnium-based ILs with the bis(trifluoromethylsulfonyl)imide and bis(perfluoroethylsulfonyl)imide anions were aged for 2520 h (15 weeks) at 200 °C in air to determine the effects of an oxidizing environment on their chemical structure and thermal stability over time. Finally, it was found that the minor changes in the cation chemistry could greatlymore » affect the properties of the ILs over time.« less

Electrochemical performance and interfacial properties of Li-metal in lithium bis(fluorosulfonyl)imide based electrolytes.

PubMed

Younesi, Reza; Bardé, Fanny

2017-11-21

Successful usage of lithium metal as the negative electrode or anode in rechargeable batteries can be an important step to increase the energy density of lithium batteries. Performance of lithium metal in a relatively promising electrolyte solution composed of lithium bis(fluorosulfonyl)imide (LiN(SO 2 F) 2 ; LiFSI) salt dissolved in 1,2-dimethoxyethane (DME) is here studied. The influence of the concentration of the electrolyte salt -1 M or 4 M LiFSI- is investigated by varying important electrochemical parameters such as applied current density and plating capacity. X-ray photoelectron spectroscopy analysis as a surface sensitive technique is here used to analyze that how the composition of the solid electrolyte interphase varies with the salt concentration and with the number of cycles.

Composite impact strength improvement through a fiber/matrix interphase

NASA Technical Reports Server (NTRS)

Cavano, P. J.; Winters, W. E.

1975-01-01

Research was conducted to improve the impact strength and toughness of fiber/resin composites by means of a fiber coating interphase. Graphite fiber/epoxy resin composites were fabricated with four different fiber coating systems introduced in a matrix-fiber interphase. Two graphite fibers, a high strength and a high modulus type, were studied with the following coating systems: chemical vapor deposited boron, electroless nickel, a polyamide-imide resin and a thermoplastic polysulfone resin. Evaluation methods included the following tests: Izod, flexure, shear fracture toughness, longitudinal and transverse tensile, and transverse and longitudinal compression. No desirable changes could be effected with the high strength fiber, but significant improvements in impact performance were observed with the polyamide-imide resin coated high modulus fiber with no loss in composite modulus.

Pre-transplantation novel agent induction predicts progression-free survival for patients with immunoglobulin light-chain amyloidosis undergoing high-dose melphalan and autologous stem cell transplantation.

PubMed

Cowan, Andrew J; Klippel, Zandra K; Stevenson, Philip A; Hyun, Teresa S; Tuazon, Sherilyn; Becker, Pamela S; Green, Damian J; Holmberg, Leona A; Coffey, David G; Gopal, Ajay K; Libby, Edward N

2016-12-01

High-dose melphalan and autologous stem cell transplantation (HDM/SCT) is an effective treatment modality for immunoglobulin light-chain (AL) amyloidosis; however, its application remains restricted to patients with good performance status and limited organ involvement. In recent years, the paradigm for AL amyloidosis has changed with the introduction of novel agents such as immunomodulatory drugs (IMiDs) and proteasome inhibitors (PIs). We hypothesized that use of novel agent induction regimens has improved outcomes for patients with AL amyloidosis undergoing HDM/SCT at our center. All patients with AL amyloidosis, age ≥18 years who underwent HDM/SCT between 2001 and 2014 at the Fred Hutchinson Cancer Research Center and University of Washington Medical Center were included in this study. Any regimen administered within 6 months prior to HDM/SCT including an IMiD or a PI was considered a novel induction regimen. Use of induction regimen was evaluated in a Cox proportional hazard model for association with progression-free survival (PFS) and overall survival (OS). Forty-five patients with AL amyloidosis underwent HDM/SCT. The median age was 57.2 years (range 39-74.4), 15 (33.3%) were women. The median number of organs involved was 2 (range 1-5), with 20 patients having only 1 (44.4%), 10 patients having 2 (22.2%), and 15 patients (33.3%) having ≥ 3 organs involved. Novel agent induction regimens were used prior to HDM/SCT in 21 patients (46.7%); these comprised PI in 13/21 (57.1%), IMiD alone in 6/21 (28.6%), PI and cyclophosphamide (CyBorD) in 3/21 (14.3%), and IMiD and PI in 3/21 (14.3%). Use of a novel agent induction regimen was associated with improved, but not OS. The 3-year PFS for patients who received a novel agent induction was 79%, while for those who did not was 53% (hazard ratio [HR] = 0.317, p = 0.048). The 3-year OS for patients who received novel agent induction regimens was 95%, while for those who did not was 71% (HR = 0.454, p = 0.247). Our data suggest that use of a novel agent induction regimen including an IMiD or PI prior to HDM/SCT for patients with AL amyloidosis could improve outcomes, with improvement in PFS. Although these results are limited by sample size and lack of randomization, these results support possible further investigation of novel agent induction regimens in the context of a prospective clinical trial.

Thalidomide

MedlinePlus

... biology of immunomodulatory drugs (IMiDs) in cancer. Pharmacology & Therapeutics. 2012;136:56. Thalomid (prescribing information). Summit, N. ... Behcet disease. In: Treatment of Skin Disease: Comprehensive Therapeutic Strategies. 4th ed. Philadelphia, Pa.: Saunders Elsevier; 2014. ...

Arylation of Rhodium(II) Azavinyl Carbenes with Boronic Acids

PubMed Central

Selander, Nicklas; Worrell, Brady T.; Chuprakov, Stepan; Velaparthi, Subash; Fokin, Valery V.

2013-01-01

A highly efficient and stereoselective arylation of in situ generated azavinyl carbenes affording 2,2-diaryl enamines at ambient temperatures has been developed. These transition metal carbenes are directly produced from readily available and stable 1-sulfonyl-1,2,3-triazoles in the presence of a rhodium carboxylate catalyst. In several cases, the enamines generated in this reaction can be cyclized into substituted indoles employing copper catalysts. PMID:22913576

Computational study of productive and non-productive cycles in fluoroalkene metathesis.

PubMed

Rybáčková, Markéta; Hošek, Jan; Šimůnek, Ondřej; Kolaříková, Viola; Kvíčala, Jaroslav

2015-01-01

A detailed DFT study of the mechanism of metathesis of fluoroethene, 1-fluoroethene, 1,1-difluoroethene, cis- and trans-1,2-difluoroethene, tetrafluoroethene and chlorotrifluoroethene catalysed with the Hoveyda-Grubbs 2(nd) generation catalyst was performed. It revealed that a successful metathesis of hydrofluoroethenes is hampered by a high preference for a non-productive catalytic cycle proceeding through a ruthenacyclobutane intermediate bearing fluorines in positions 2 and 4. Moreover, the calculations showed that the cross-metathesis of perfluoro- or perhaloalkenes should be a feasible process and that the metathesis is not very sensitive to stereochemical issues.

The Toxicology of Perfluorodecanoic Acid in Rodents,

DTIC Science & Technology

Perfluoro -n-decanoic acid or nonadecafluoro-n-decanoic acid (NDFDA) is a straight chain, perfluorinated , ten-carbon acid. Experiments were conducted...to determine the LD50 and to evaluate survival times of rats after single intraperitoneal (IP) injections of NDFDA or of Fluorooctanoic acid ( PFOA ...experimental animals. With NDFDA, the LD50/14 days was 63.6 mg/kg, and the LD50/30 days was 41.4 mg/kg. With PFOA , there was no mortality after the 5th day following injection, and both the LD50/14 and LD50/30 were 188.7 mg/kg.

Apparatus for silicon nitride precursor solids recovery

DOEpatents

Crosbie, Gary M.; Predmesky, Ronald L.; Nicholson, John M.

1995-04-04

Method and apparatus are provided for collecting reaction product solids entrained in a gaseous outflow from a reaction situs, wherein the gaseous outflow includes a condensable vapor. A condensate is formed of the condensable vapor on static mixer surfaces within a static mixer heat exchanger. The entrained reaction product solids are captured in the condensate which can be collected for further processing, such as return to the reaction situs. In production of silicon imide, optionally integrated into a production process for making silicon nitride caramic, wherein reactant feed gas comprising silicon halide and substantially inert carrier gas is reacted with liquid ammonia in a reaction vessel, silicon imide reaction product solids entrained in a gaseous outflow comprising residual carrier gas and vaporized ammonia can be captured by forming a condensate of the ammonia vapor on static mixer surfaces of a static mixer heat exchanger.

Method for silicon nitride precursor solids recovery

DOEpatents

Crosbie, Gary M.; Predmesky, Ronald L.; Nicholson, John M.

1992-12-15

Method and apparatus are provided for collecting reaction product solids entrained in a gaseous outflow from a reaction situs, wherein the gaseous outflow includes a condensable vapor. A condensate is formed of the condensable vapor on static mixer surfaces within a static mixer heat exchanger. The entrained reaction product solids are captured in the condensate which can be collected for further processing, such as return to the reaction situs. In production of silicon imide, optionally integrated into a production process for making silicon nitride caramic, wherein reactant feed gas comprising silicon halide and substantially inert carrier gas is reacted with liquid ammonia in a reaction vessel, silicon imide reaction product solids entrained in a gaseous outflow comprising residual carrier gas and vaporized ammonia can be captured by forming a condensate of the ammonia vapor on static mixer surfaces of a static mixer heat exchanger.

Durable electrooptic devices comprising ionic liquids

DOEpatents

Burrell, Anthony K [Los Alamos, NM; Agrawal, Anoop [Tucson, AZ; Cronin,; John, P [Tucson, AZ; Tonazzi, Juan C. L. [Tucson, AZ; Warner, Benjamin P [Los Alamos, NM; McCleskey, T Mark [Los Alamos, NM

2009-12-15

Electrolyte solutions for electrochromic devices such as rear view mirrors and displays with low leakage currents are prepared using inexpensive, low conductivity conductors. Preferred electrolytes include bifunctional redox dyes and molten salt solvents with enhanced stability toward ultraviolet radiation. The solvents include lithium or quaternary ammonium cations, and perfluorinated sulfonylimide anions selected from trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3C.sup.-). Electroluminescent, electrochromic and photoelectrochromic devices with nanostructured electrodes include ionic liquids with bifunctional redox dyes. Some of the electrolyte solutions color to red when devices employing the solutions are powered, leading to red or neutral electrooptic devices.

Copoly(imide-amides) containing hexafluoroisopropylidene

NASA Technical Reports Server (NTRS)

Irvin, David J.; Cassidy, Patrick E.; Cameron, Mitch L.

1990-01-01

The incorporation of the hexafluoroisopropylidene (HFIP or 6F) group into polymer backbones brings about important and useful changes in properties. These differences include increased thermal and environmental resistance and solubility and decreased dielectric constant and color. Several types of backbones have been substrates for the inclusion of HFIP and all results have reflected impressive property benefits. This project involved the incorporation of 6F groups into a poly(imide-amide) backbone by the condensation of a 6F-containing dianhydride with 4-aminobenzoic acid to yield a diimide terminated with two carboxylic acid groups. This diacid trimer was then polymerized with various diamines. The polymers were obtained in yields of 86-94 percent and with viscosities of 0.90-2.26 dL/g. They were stable to above 500 C and clear, colorless films could be cast from DMAc.

Small nickel nanoparticle arrays from long chain imidazolium ionic liquids

DOE PAGES

Yang, Mei; Campbell, Paul S.; Santini, Catherine C.; ...

2013-11-08

A series of six long chain alkyl mono- and bi-cationic imidazolium based salts with bis(trifluoromethylsulfonyl)imide (NTf 2–) as the anion were synthesized and characterized. Single crystal structure of 1-methyl-3-octadecylimidazolium bis(trifluoromethylsulfonyl)imide could be obtained by X-ray analysis. All these long chain alkyl imidazolium based ILs were applied in the synthesis of nickel nanoparticles via chemical decomposition of an organometallic precursor of nickel. In these media, spontaneous decomposition of Ni(COD) 2 (COD = 1,5-cyclooctadiene) in the absence of H 2 occurred giving small NPs (≤4 nm) with narrow size distributions. Interestingly, formation of regularly interspaced NP arrays was also observed in longmore » chain ILs. Lastly, such array formation could be interesting for potential applications such as carbon nanotube growth.« less

FABRICATION OF A RETINAL PROSTHETIC TEST DEVICE USING ELECTRODEPOSITED SILICON OVER POLYPYRROLE PATTERNED WITH SU-8 PHOTORESIST

PubMed Central

Miller, Eric; Ellis, Daniel; Charles, Duran; McKenzie, Jason

2016-01-01

A materials fabrication study of a photodiode array for possible application of retina prosthesis was undertaken. A test device was fabricated using a glassy carbon electrode patterned with SU-8 photoresist. In the openings, p-type polypyrrole was first electrodeposited using 1-butyl-1-methylpyridinium bis(trifluoromethylsulfonyl)imide ionic liquid. The polypyrrole was self-doped with imide ion at ~1.5 mole %, was verified as p-type, and had a resistivity of ~20 Ωcm. N-type Silicon was then electrodeposited over this layer using silicon tetrachloride / phosphorus trichloride in acetonitrile and passivated in a second electrodeposition using trimethylchlorosilane. Electron microscopy revealed the successful electrodeposition of silicon over patterned polypyrrole. Rudimentary photodiode behavior was observed. The passivation improved but did not completely protect the electrodeposited silicon from oxidation by air. PMID:27616940

Chaotropic salts: novel modifiers for the capillary electrophoretic analysis of benzodiazepines.

PubMed

Su, Hsiu-Li; Lan, Min-Tsu; Lin, Kuan-Wen; Hsieh, You-Zung

2008-08-01

This paper describes a CE method for analyzing benzodiazepines using the chaotropic salts lithium trifluoromethanesulfonate (LiOTf), lithium hexafluorophosphate (LiPF(6)), and lithium bis(trifluoromethanesulfonyl)imide (LiNTf(2)) as modifiers in the running buffer. Although adequate resolution of seven benzodiazepine analytes occurred under the influence of each of the chaotropic anions, the separation efficiency was highest when bis(trifluoromethanesulfonyl)imide (Tf(2)N(-)) was the modifier. We applied affinity CE in conjunction with linear analysis to determine the association constants for the formation of complexes between the Tf(2)N(-) anion and the benzodiazepines. According to the estimated Gibbs free energies, the interactions between this chaotropic anion and the benzodiazepines were either ion-dipole or ion-induced dipole interactions. Adding chaotropic salts as modifiers into CE buffers is a simple and reproducible technique for separating benzodiazepines.

Physical properties of ionic liquids consisting of the 1-butyl-3-methylimidazolium cation with various anions and the bis(trifluoromethylsulfonyl)imide anion with various cations.

PubMed

Jin, Hui; O'Hare, Bernie; Dong, Jing; Arzhantsev, Sergei; Baker, Gary A; Wishart, James F; Benesi, Alan J; Maroncelli, Mark

2008-01-10

Physical properties of 4 room-temperature ionic liquids consisting of the 1-butyl-3-methylimidazolium cation with various perfluorinated anions and the bis(trifluoromethylsulfonyl)imide (Tf2N-) anion with 12 pyrrolidinium-, ammonium-, and hydroxyl-containing cations are reported. Electronic structure methods are used to calculate properties related to the size, shape, and dipole moment of individual ions. Experimental measurements of phase-transition temperatures, densities, refractive indices, surface tensions, solvatochromic polarities based on absorption of Nile Red, 19F chemical shifts of the Tf2N- anion, temperature-dependent viscosities, conductivities, and cation diffusion coefficients are reported. Correlations among the measured quantities as well as the use of surface tension and molar volume for estimating Hildebrand solubility parameters of ionic liquids are also discussed.

Polymer electrolyte based on crosslinked poly(glycidyl methacrylate) and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fei, Beatrice Wong Chui; Hanifah, Sharina Abu; Ahmad, Azizan

2015-09-25

Polymer electrolytes based on crosslinked poly(glycidyl methacrylate) as polymer host and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (BmimTFSI) as incorporated salt were prepared by in-situ photopolymerization technique. The complexes with different mass ratio of glycidyl methacrylate (GMA) monomer to BmimTFSI were investigated. The ionic conductivity of the polymer electrolyte was increased and reach the highest value of 7.50 × 10{sup −4} S cm{sup −1} at the ratio of 3:7 (GMA: BmimTFSI). The interaction between the polymer host and ionic liquid was proved by Attenuated Total Reflectance-Fourier Transformation Infra-Red Spectroscopy (ATR-FTIR). Meanwhile, the X-ray diffraction analysis shows the amorphousity of the polymer electrolyte film increasemore » with the ionic liquid ratio.« less

New addition curing polyimides

NASA Technical Reports Server (NTRS)

Frimer, Aryeh A.; Cavano, Paul

1991-01-01

In an attempt to improve the thermal-oxidative stability (TOS) of PMR-type polymers, the use of 1,4-phenylenebis (phenylmaleic anhydride) PPMA, was evaluated. Two series of nadic end-capped addition curing polyimides were prepared by imidizing PPMA with either 4,4'-methylene dianiline or p-phenylenediamine. The first resulted in improved solubility and increased resin flow while the latter yielded a compression molded neat resin sample with a T(sub g) of 408 C, close to 70 C higher than PME-15. The performance of these materials in long term weight loss studies was below that of PMR-15, independent of post-cure conditions. These results can be rationalized in terms of the thermal lability of the pendant phenyl groups and the incomplete imidization of the sterically congested PPMA. The preparation of model compounds as well as future research directions are discussed.

Low pressure process for continuous fiber reinforced polyamic acid resin matrix composite laminates

NASA Technical Reports Server (NTRS)

Druyun, Darleen A. (Inventor); Hou, Tan-Hung (Inventor); Kidder, Paul W. (Inventor); Reddy, Rakasi M. (Inventor); Baucom, Robert M. (Inventor)

1994-01-01

A low pressure processor was developed for preparing a well-consolidated polyimide composite laminate. Prepreg plies were formed from unidirectional fibers and a polyamic acid resin solution. Molding stops were placed at the sides of a matched metal die mold. The prepreg plies were cut shorter than the length of the mold in the in-plane lateral direction and were stacked between the molding stops to a height which was higher than the molding stops. The plies were then compressed to the height of the stops and heated to allow the volatiles to escape and to start the imidization reaction. After removing the stops from the mold, the heat was increased and 0 - 500 psi was applied to complete the imidization reaction. The heat and pressure were further increased to form a consolidated polyimide composite laminate.

Durable Electrooptic Devices Comprising Ionic Liquids

DOEpatents

Burrell, Anthony K.; Agrawal, Anoop; Cronin, John P.; Tonazzi, Juan C. L.; Warner, Benjamin P.; McCleskey, T. Mark

2008-11-11

Electrolyte solutions for electrochromic devices such as rear view mirrors and displays with low leakage currents are prepared using inexpensive, low conductivity conductors. Preferred electrolytes include bifunctional redox dyes and molten salt solvents with enhanced stability toward ultraviolet radiation. The solvents include lithium or quaternary ammonium cations, and perfluorinated sulfonylimide anions selected from trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3C.sup.-). Electroluminescent, electrochromic and photoelectrochromic devices with nanostructured electrodes include ionic liquids with bifunctional redox dyes. Some of the electrolyte solutions color to red when devices employing the solutions are powered, leading to red or neutral electrooptic devices.

Effects of Imide-Orthoborate Dual-Salt Mixtures in Organic Carbonate Electrolytes on the Stability of Lithium Metal Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xing; Zheng, Jianming; Engelhard, Mark H.

The effects of lithium imide and lithium orthoborate dual-salt electrolytes of different salt chemistries in carbonate solvents on the cycling stability of lithium (Li) metal batteries are systematically and comparatively investigated. Two imide salts (LiTFSI and LiFSI) and two orthoborate salts (LiBOB and LiDFOB) are chosen for this study and compared with the conventional LiPF6 salt. Density functional theory calculations indicate that the chemical and electrochemical stabilities follow the order of LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiDFOB > LiFSI-LiBOB. The experimental cycling stability of the Li metal batteries with the electrolytes follows the order as LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiDFOB >more » LiPF6 > LiFSI-LiBOB, which is in well accordance with the calculation results. The LiTFSI-LiBOB can effectively protect the Al substrate and form a more robust surface film on Li metal anode, while the LiFSI-LiBOB results in serious corrosion to the stainless steel cell case and a thicker and looser surface film on Li anode. In conclusion, the key findings of this work emphasize that the salt chemistry is critically important for enhancing the interfacial stability of Li metal anode and should be carefully manipulated in the development of high performance Li metal batteries.« less

Effects of Imide-Orthoborate Dual-Salt Mixtures in Organic Carbonate Electrolytes on the Stability of Lithium Metal Batteries

DOE PAGES

Li, Xing; Zheng, Jianming; Engelhard, Mark H.; ...

2017-12-27

The effects of lithium imide and lithium orthoborate dual-salt electrolytes of different salt chemistries in carbonate solvents on the cycling stability of lithium (Li) metal batteries are systematically and comparatively investigated. Two imide salts (LiTFSI and LiFSI) and two orthoborate salts (LiBOB and LiDFOB) are chosen for this study and compared with the conventional LiPF6 salt. Density functional theory calculations indicate that the chemical and electrochemical stabilities follow the order of LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiDFOB > LiFSI-LiBOB. The experimental cycling stability of the Li metal batteries with the electrolytes follows the order as LiTFSI-LiBOB > LiTFSI-LiDFOB > LiFSI-LiDFOB >more » LiPF6 > LiFSI-LiBOB, which is in well accordance with the calculation results. The LiTFSI-LiBOB can effectively protect the Al substrate and form a more robust surface film on Li metal anode, while the LiFSI-LiBOB results in serious corrosion to the stainless steel cell case and a thicker and looser surface film on Li anode. In conclusion, the key findings of this work emphasize that the salt chemistry is critically important for enhancing the interfacial stability of Li metal anode and should be carefully manipulated in the development of high performance Li metal batteries.« less

Space Environmentally Stable Polyimides and Copolyimides

NASA Technical Reports Server (NTRS)

Watson, Kent A.; Connell, John W.

2000-01-01

Polyimides with a unique combination of properties including low color in thin films, atomic oxygen (AO), ultra-violet (UV) radiation resistance, solubility in organic solvents in the imide form, high glass transition (T(sub g)) temperatures and high thermal stability have been prepared and characterized. The polymers were prepared by reacting a novel aromatic diamine with aromatic dianhydrides in a polar aprotic solvent. The solubility of the polymers in the imide form as well as the color density of thin films were dependent upon the chemical structure of the dianhydride. Several thin films (25-50 mm thick) prepared by solution casting of amide acid or imide solutions exhibited very low color and high optical transparency (approximately 90%) as determined by UV/visible spectroscopy. The polymers exhibited T(sub g)s >200 C depending upon the structure of the dianhydride and temperatures of 5% weight loss approximately 500C in air as determined by dynamic thermogravimetric analysis. Thin films coated with silver/inconel were exposed to a high fluence of AO and 1000 equivalent solar hours of UV radiation. The effects of these exposures on optical properties were minor. These space environmentally durable polymers are potentially useful in a variety of applications on spacecraft such as thin film membranes on antennas, second-surface mirrors, thermal/optical coatings and multi-layer thermal insulation (MLI) blanket materials. The chemistry, physical and mechanical properties of the polymers as well as their responses to AO and UV exposure will be discussed.

Phosphatidylserine-exposing cells contribute to the hypercoagulable state in patients with multiple myeloma.

PubMed

Guo, Li; Tong, Dongxia; Yu, Muxin; Zhang, Yan; Li, Tao; Wang, Chunxu; Zhou, Peng; Jin, Jiaqi; Li, Baorong; Liu, Yingmiao; Liu, Ruipeng; Novakovic, Valerie A; Dong, Zengxiang; Tian, Ye; Kou, Junjie; Bi, Yayan; Zhou, Jin; Shi, Jialan

2018-06-01

Multiple myeloma (MM) is characterized by an increased incidence of thromboembolic events, particularly when treated with immunomodulatory drugs (IMiDs) in combination with dexamethasone. The optimal prophylactic strategy to prevent the hypercoagulable state of patients with MM is still debated. The aim of the current study was to investigate the definitive role of phosphatidylserine (PS) in supporting procoagulant activity (PCA) in patients with MM. Patients with MM (n=20) and healthy subjects (n=15) were recruited for the present study. PS analyses were performed by flow cytometry and confocal microscopy. The PCA was evaluated by clotting time, purified coagulation complex assays and fibrin production assays. The percentage of PS+ blood cells was significantly higher in patients with MM than in healthy subjects. Additionally, the patient serum induced more PS exposure on endothelial cells (ECs) in vitro than serum from healthy subjects. Isolated blood cells from patients with MM and ECs cultured with patient serum in vitro demonstrated significantly shortened coagulation time, greatly intrinsic/extrinsic factor Xa generation and increased thrombin formation. In addition, the levels of PS+ erythrocytes, platelets, leukocytes, and ECs incubated with IMiDs and dexamethasone were higher than with IMiDs alone. The findings support the hypothesis that increased PS exposure on blood cells and ECs participates in the hypercoagulable state in patients with MM. Thus, blocking PS may be a novel therapeutic target for the prevention of thrombosis in these patients.

Fluorination of silicone rubber by plasma polymerization

NASA Astrophysics Data System (ADS)

Fielding, Jennifer Chase

Plasma polymerized fluorocarbon (PPFC) films were deposited onto various silicone rubber substrates, including O-rings, to decrease oil uptake. Depositions were performed using a radio frequency (rf)-powered plasma reactor and various fluorocarbon monomers, such as C2F6, C2F 5H, C3F6, and 1H,1H,2H-perfluoro-1-dodecene. PPFC films which were most promising for inhibiting oil uptake were deposited with 1H,1H,2H-perfluoro-1-dodecene, and were composed predominantly of perfluoromethylene (CF2) species. These films displayed low critical surface energies (as low as 2.7 mJ/m2), and high contact angles with oil (84°), which were correlated with the amount of CF2 species present in the film. For the films with the highest degree of CF2 (up to 67%), CF2 chains may have been oriented slightly perpendicular to the substrate and terminated by CF3 species. Adhesion of the PPFC films directly to silicone rubber was found to be poor. However, when a plasma polymerized hydrocarbon interlayer was deposited on the silicone rubber prior to the fluorocarbon films, adhesion was excellent. O-rings coated with multilayer fluorocarbon films showed 2.6% oil uptake after soaking in oil for 100 hrs at 100°C. Due to variability in data, and the low quality of the industrial grade silicone rubber, the oil uptake mechanism was determined to be from oil flowing through flaws in the film due to defects within the substrate, not from generalized diffusion through the film. This mechanism was confirmed using higher quality silicone rubber, which showed little or no oil diffusion. Therefore, this film may perform well as an oil-repelling barrier when deposited on a high quality silicone rubber.

Poly-N-Isopropylacrylamide/acrylic Acid Copolymers for the Generation of Nanostructures at Mica Surfaces and as Hydrophobic Host Systems for the Porin MspA from Mycobacterium smegmatis.

PubMed

Gamage, Pubudu; Basel, Matthew T; Lovell, Kimberly; Pokhrel, Megh Raj; Battle, Deletria; Ito, Takashi; Pavlenok, Mikhail; Niederweis, Michael; Bossmann, Stefan H

2009-09-17

The work presented here aims at utilizing poly-N-isopropyl-acrylamide/acrylic acid copolymers to create nanostructured layers on mica surfaces by a simple spin-casting procedure. The average composition of the copolymers determined by elemental analysis correlates excellently with the feed composition indicating that the radical polymerization process is statistical. The resulting surfaces were characterized by Atomic Force Microscopy (magnetic AC-mode) at the copolymer/air interface. Postpolymerization modification of the acrylic acid functions with perfluoro-octyl-iodide decreased the tendency towards spontaneous formation of nanopores. Crosslinking of individual polymer chains permitted the generation of ultraflat layers, which hosted the mycobacterial channel protein MspA, without compromising its channel function. The comparison of copolymers of very similar chemical composition that have been prepared by living radical polymerization and classic radical polymerization indicated that differences in polydispersity played only a minor role when poly-N-isopropyl-acrylamide/acrylic acid copolymers were spincast, but a major role when copolymers featuring the strongly hydrophobic perfluoro-octyl-labels were used. The mean pore diameters were 23.8+/-4.4 nm for P[(NIPAM)(95.5)-co-(AA)(4.5)] (PDI (polydispersity index)=1.55) and 21.8+/-4.2 nm for P[(NIPAM)(95.3)-co-(AA)(4.7)] (PDI=1.25). The depth of the nanopores was approx. 4 nm. When depositing P[(NIPAM)(95)-co-(AA)(2.8)-AAC(8)F(17 2.2)] (PDI=1.29) on Mica, the resulting mean pore diameter was 35.8+/-7.1 nm, with a depth of only 2 nm.

Poly-N-Isopropylacrylamide/acrylic Acid Copolymers for the Generation of Nanostructures at Mica Surfaces and as Hydrophobic Host Systems for the Porin MspA from Mycobacterium smegmatis

PubMed Central

Gamage, Pubudu; Basel, Matthew T.; Lovell, Kimberly; Pokhrel, Megh Raj; Battle, Deletria; Ito, Takashi; Pavlenok, Mikhail; Niederweis, Michael

2009-01-01

The work presented here aims at utilizing poly-N-isopropyl-acrylamide/acrylic acid copolymers to create nanostructured layers on mica surfaces by a simple spin-casting procedure. The average composition of the copolymers determined by elemental analysis correlates excellently with the feed composition indicating that the radical polymerization process is statistical. The resulting surfaces were characterized by Atomic Force Microscopy (magnetic AC-mode) at the copolymer/air interface. Postpolymerization modification of the acrylic acid functions with perfluoro-octyl-iodide decreased the tendency towards spontaneous formation of nanopores. Crosslinking of individual polymer chains permitted the generation of ultraflat layers, which hosted the mycobacterial channel protein MspA, without compromising its channel function. The comparison of copolymers of very similar chemical composition that have been prepared by living radical polymerization and classic radical polymerization indicated that differences in polydispersity played only a minor role when poly-N-isopropyl-acrylamide/acrylic acid copolymers were spincast, but a major role when copolymers featuring the strongly hydrophobic perfluoro-octyl-labels were used. The mean pore diameters were 23.8±4.4 nm for P[(NIPAM)95.5-co-(AA)4.5] (PDI (polydispersity index)=1.55) and 21.8±4.2 nm for P[(NIPAM)95.3-co-(AA)4.7] (PDI=1.25). The depth of the nanopores was approx. 4 nm. When depositing P[(NIPAM)95-co-(AA)2.8-AAC8F17 2.2] (PDI=1.29) on Mica, the resulting mean pore diameter was 35.8±7.1 nm, with a depth of only 2 nm. PMID:20161351

Perfluoroalkylated substances (PFAS) affect neither estrogen and androgen receptor activity nor steroidogenesis in human cells in vitro.

PubMed

Behr, Anne-Cathrin; Lichtenstein, Dajana; Braeuning, Albert; Lampen, Alfonso; Buhrke, Thorsten

2018-07-01

The perfluoroalkylated substances (PFAS) perfluorooctanesulfonic acid (PFOS) and perfluorooctanoic acid (PFOA) are used for the fabrication of water- and dirt-repellent surfaces. The use of PFOS and PFOA was restricted due to their reprotoxic properties and their environmental persistence. Therefore, industry switches to alternative PFAS, however, in contrast to PFOA and PFOS only few toxicological data are available for their substitutes. The molecular mechanism(s) underlying reproductive toxicity of PFOA and PFOS are largely unknown. Here, the endocrine properties of PFOA, PFOS, and of six substitutes including perfluorohexanesulfonic acid (PFHxS), perfluorobutanesulfonic acid (PFBS), perfluorohexanoic acid (PFHxA), perfluorobutanoic acid (PFBA), ammonium perfluoro(2-methyl-3-oxahexanoate) (PMOH), and 3H-perfluoro-3-[(3-methoxypropoxy) propanoic acid] (PMPP) were examined in vitro by using human cell lines such as MCF-7, H295R, LNCaP and MDA-kb2. PFOA, PFOS and PMOH enhanced 17β-estradiol-stimulated estrogen receptor β activity, and PFOS, PMOH, PFHxA and PFBA enhanced dihydrotestosterone-stimulated androgen receptor activity. In the H295R steroidogenesis assay, PFOA and PFOS slightly enhanced estrone secretion, and progesterone secretion was marginally increased by PFOA. All these effects were only observed at concentrations above 10 μM, and none of the PFAS displayed any effect on any of the molecular endocrine endpoints at concentrations of 10 μM or below. Thus, as the blood serum concentrations of the different PFAS in the general Western population are in the range of 10 nM or below, the results suggest that PFAS might not exert endocrine effects in humans at exposure-relevant concentrations according to the molecular endpoints examined in this study. Copyright © 2018 Elsevier B.V. All rights reserved.

Molecular dynamics averaging of Xe chemical shifts in liquids.

PubMed

Jameson, Cynthia J; Sears, Devin N; Murad, Sohail

2004-11-15

The Xe nuclear magnetic resonance chemical shift differences that afford the discrimination between various biological environments are of current interest for biosensor applications and medical diagnostic purposes. In many such environments the Xe signal appears close to that in water. We calculate average Xe chemical shifts (relative to the free Xe atom) in solution in eleven liquids: water, isobutane, perfluoro-isobutane, n-butane, n-pentane, neopentane, perfluoroneopentane, n-hexane, n-octane, n-perfluorooctane, and perfluorooctyl bromide. The latter is a liquid used for intravenous Xe delivery. We calculate quantum mechanically the Xe shielding response in Xe-molecule van der Waals complexes, from which calculations we develop Xe (atomic site) interpolating functions that reproduce the ab initio Xe shielding response in the complex. By assuming additivity, these Xe-site shielding functions can be used to calculate the shielding for any configuration of such molecules around Xe. The averaging over configurations is done via molecular dynamics (MD). The simulations were carried out using a MD technique that one of us had developed previously for the simulation of Henry's constants of gases dissolved in liquids. It is based on separating a gaseous compartment in the MD system from the solvent using a semipermeable membrane that is permeable only to the gas molecules. We reproduce the experimental trends in the Xe chemical shifts in n-alkanes with increasing number of carbons and the large chemical shift difference between Xe in water and in perfluorooctyl bromide. We also reproduce the trend for a given solvent of decreasing Xe chemical shift with increasing temperature. We predict chemical shift differences between Xe in alkanes vs their perfluoro counterparts.

Organic anion transporter 4 (OAT 4) modifies placental transfer of perfluorinated alkyl acids PFOS and PFOA in human placental ex vivo perfusion system.

PubMed

Kummu, M; Sieppi, E; Koponen, J; Laatio, L; Vähäkangas, K; Kiviranta, H; Rautio, A; Myllynen, P

2015-10-01

Perfluorinated alkyl acids (PFAAs) are widely used in industry and consumer products. Pregnant women are exposed to PFAAs and their presence in umbilical cord blood represents fetal exposure. Interestingly, PFAAs are substrates for organic anion transporters (OAT) of which OAT4 is expressed in human placenta. To evaluate the contribution of OAT4 and ATP-binding cassette transporter G2 (ABCG2) proteins in the transplacental transfer of perfluoro octane sulfonate (PFOS) and perfluoro octanoate (PFOA) an ex vivo dual recirculating human placental perfusion was used. Altogether 8 placentas from healthy mothers with uncomplicated pregnancies were successfully perfused. Both PFOS and PFOA crossed the placenta as suggested by in vivo data in the literature. The expression of OAT4 and ABCG2 proteins were studied by immunoblotting and correlation with the transfer index %(TI %) of PFOS and PFOA at 120 and 240 min (n = 4) was studied. The expression of OAT4 was in negative correlation with TI % of PFOA (R(2) = 0.92, p = 0.043) and PFOS (R(2) = 0.99, p = 0.007) at 120 min while at 240 min the correlation was statistically significant only with PFOA. The expression of ABCG2 did not correlate with TI% of PFOS or PFOA. Data obtained in this study suggest the involvement of OAT4 in placental passage of PFAAs. Placental passage of PFOS and PFOA is modified by the transporter protein OAT4 but not by ABCG2. This is the first study indicating that OAT4 may decrease the fetal exposure to PFAAs and protect the fetus after maternal exposure to PFAAs but further studies are needed to confirm our findings. Copyright © 2015 Elsevier Ltd. All rights reserved.

Sulfonyl-containing modulators of serotonin 5-HT6 receptors and their pharmacophore models

NASA Astrophysics Data System (ADS)

Ivachtchenko, A. V.

2014-05-01

Data published in recent years on the synthesis of serotonin 5-HT6 receptor modulators are summarized. Modulators with high affinity for 5-HT6 receptors exhibiting different degrees of selectivity — from highly selective to semiselective and multimodal — are described. Clinical trial results are reported for the most promising serotonin 5-HT6 receptor modulators attracting special attention of medicinal chemists. The bibliography includes 128 references.

Safety of live vaccinations on immunosuppressive therapy in patients with immune-mediated inflammatory diseases, solid organ transplantation or after bone-marrow transplantation - A systematic review of randomized trials, observational studies and case reports.

PubMed

Croce, Evelina; Hatz, Christoph; Jonker, Emile F; Visser, L G; Jaeger, Veronika K; Bühler, Silja

2017-03-01

Live vaccines are generally contraindicated on immunosuppressive therapy due to safety concerns. However, data are limited to corroborate this practice. To estimate the safety of live vaccinations in patients with immune-mediated inflammatory diseases (IMID) or solid organ transplantation (SOT) on immunosuppressive treatment and in patients after bone-marrow transplantation (BMT). A search was conducted in electronic databases (Cochrane, Pubmed, Embase) and additional literature was identified by targeted searches. Randomized trials, observational studies and case reports. Patients with IMID or SOT on immunosuppressive treatment and BMT patients <2years after transplantation. Live vaccinations: mumps, measles, rubella (MMR), yellow fever (YF), varicella vaccine (VV), herpes zoster (HZ), oral typhoid, oral polio, rotavirus, Bacillus Calmette-Guérin (BCG), smallpox. One author performed the data extraction using predefined data fields. It was cross-checked by two other authors. 7305 articles were identified and 64 articles were included: 40 on IMID, 16 on SOT and 8 on BMT patients. In most studies, the administration of live vaccines was safe. However, some serious vaccine-related adverse events occurred. 32 participants developed an infection with the vaccine strain; in most cases the infection was mild. However, in two patients fatal infections were reported: a patient with RA/SLE overlap who started MTX/dexamethasone treatment four days after the YFV developed a yellow fever vaccine-associated viscerotropic disease (YEL-AVD) and died. The particular vaccine lot was found to be associated with a more than 20 times risk of YEL-AVD. One infant whose mother was under infliximab treatment during pregnancy received the BCG vaccine at the age of three months and developed disseminated BCG infection and died. An immunogenicity assessment was performed in 43 studies. In most cases the patients developed satisfactory seroprotection rates. In the IMID group, YFV and VV demonstrated high seroconversion rates. MTX and tumor necrosis factor inhibitory therapy appeared to reduce immune responses to VV and HZ vaccine, but not to MMR and YF-revaccination. Seroconversion in SOT and BMT patients showed mostly higher rates for rubella than for measles, mumps and varicella. Risk of bias was high in the majority of studies since 39 of them were observational and 17 were case series/case reports. Only eight studies were randomized trials. BMT patient numbers included in this review were low. Although live vaccinations were safe and sufficiently immunogenic in most studies, some serious reactions and vaccine-related infections were reported in immunosuppressed IMID and SOT patients. Apart from mild vaccine-related infections MMR and VV vaccines were safe when administered less than two years after BMT. Until further data are available, live vaccinations under most immunosuppressive treatments should only be administered after a careful risk benefit assessment of medications and dosages. None. Copyright © 2017 Elsevier Ltd. All rights reserved.

Reactive Additives for Phenylethynyl-Containing Resins

NASA Technical Reports Server (NTRS)

Connell, John W.; Smith, Joseph G., Jr.; Hergenrother, Paul M.; Rommel, Monica L.

2005-01-01

Phenylethynyl-containing reactive additive (PERA) compounds and mixtures have been found to be useful for improving the processability of oligomers, polymers, co-oligomers, and copolymers that contain phenylethynyl groups. The additives can be incorporated in different forms: A solution of an amide acid or an imide of a PERA can be added to a solution of phenylethynyl-containing oligomer, polymer, co-oligomer, or copolymer; or An imide powder of a PERA can be mixed with a dry powder of a phenylethynyl-containing oligomer, polymer, co-oligomer, or copolymer. The effect of a given PERA on the processability and other properties of the resin system depends on whether the PERA is used in the amide acid or an imide form. With proper formulation, the PERA reduces the melt viscosity of the resin and thereby reduces the processing pressures needed to form the adhesive bonds, consolidate filled or unfilled moldings, or fabricate fiber-reinforced composite laminates. During thermal cure, a PERA reacts with itself as well as with the phenylethynyl-containing host resin and thereby becomes chemically incorporated into the resin system. The effects of the PERA on mechanical properties, relative to those of the host resin, depend on the amount of PERA used. Typically, the incorporation of the PERA results in (1) increases in the glass-transition temperature (Tg), modulus of elasticity, and parameters that characterize behavior under compression, and (2) greater retention of the aforementioned mechanical properties at elevated temperatures without (3) significant reduction of toughness or damage tolerance. Of the formulations tested thus far, the ones found to yield the best overall results were those for which the host resin was the amide acid form of a phenylethynyl-terminated imide (PETI) co-oligomer having a molecular weight of 5,000 g/mole [hence, designated PETI-5] and a PERA denoted as PERA-1. PETI-5 was made from 3,3',4'4'-biphenyltetracarboxylic dianhydride, 3,4'-oxydianiline (3,4'-ODA), 1,3-bis(3-aminophenoxy) benzene (1,3-APB), and 4-phenylethynylphthalic anhydride (PEPA). PERA-1 was made from 3,5-diamino- 4.-phenylethynylbenzophenon and equimolar amounts of phthalic anhydride and PEPA. To make PERA-1 in the imide form, the aforementioned ingredients were processed by refluxing in glacial acetic acid. To make the amide form of PERA-1, the ingredients were reacted in N-methyl-2-pyrrolidinone (NMP) under nitrogen at a temperature of 23 C (see figure). On the basis of the processability and other properties, a blend comprising 20 weight percent of PERA-1 and 80 weight percent PETI-5 was selected for further evaluation. Relative to neat PETI-5, the blend exhibited an increase in Tg; improved processability; and comparable values of shear strength in adhesion to titanium panels, open-hole compressive properties, compression properties after impact, and resistance to microcracking.

Coordination-supported organic polymers: mesoporous inorganic–organic materials with preferred stability

DOE PAGES

Chen, Dong; Zhang, Pengfei; Fang, Qianrong; ...

2018-01-01

A simple and versatile strategy is developed for the synthesis of coordination-supported organic polymers(COPs) via coordination between Al 3+ and 5-amino-8-hydroxyquinoline together with organic imine- or imide-based polycondensation.

Teaching Relative Acidity in the Undergraduate Organic Chemistry Course.

ERIC Educational Resources Information Center

Traynham, James G.

1988-01-01

Described is a teaching method for connecting relative acidity among various species by the use of familiar references. Considered are teaching the acidity of alpha-hydrogens of ketones, alkylation of amides and imides, and others. (CW)

Coordination-supported organic polymers: mesoporous inorganic–organic materials with preferred stability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Dong; Zhang, Pengfei; Fang, Qianrong

A simple and versatile strategy is developed for the synthesis of coordination-supported organic polymers(COPs) via coordination between Al 3+ and 5-amino-8-hydroxyquinoline together with organic imine- or imide-based polycondensation.

Challenges in Laser Sintering of Melt-Processable Thermoset Imide Resin

NASA Technical Reports Server (NTRS)

Chuang, Kathy C.; Gornet, Timothy; Koerner, Hilmar

2016-01-01

Polymer Laser Sintering (LS) is an additive manufacturing technique that builds 3D models layer by layer using a laser to selectively melt cross sections in powdered polymeric materials, following sequential slices of the CAD model. LS generally uses thermoplastic polymeric powders, such as polyamides (i.e. Nylon), and the resultant 3D objects are often weaker in their strength compared to traditionally processed materials, due to the lack of polymer inter-chain connection in the z-direction. The objective of this project is to investigate the possibility of printing a melt-processable RTM370 imide resin powder terminated with reactive phenylethynyl groups by LS, followed by a postcure in order to promote additional crosslinking to achieve higher temperature (250-300 C) capability. A preliminary study to build tensile specimens by LS and the corresponding DSC and rheology study of RTM370 during LS process is presented.

Challenges in Laser Sintering of Thermoset Imide Resin

NASA Technical Reports Server (NTRS)

Chuang, Kathy C.; Gornet, Timothy; Koerner, Hilmar

2016-01-01

Polymer Laser Sintering (LS) is an additive manufacturing technique that builds 3D models layer by layer using a laser to selectively melt cross sections in powdered polymeric materials, following sequential slices of the CAD model. LS generally uses thermoplastic polymeric powders, such as polyamides (i.e. Nylon), and the resultant 3D objects are often weaker in their strength compared to traditionally processed materials, due to the lack of polymer inter-chain connection in the z-direction. The objective of this project is to investigate the possibility of printing a melt-processable RTM370 imide resin powder terminated with reactive phenylethynyl groups by LS, followed by a postcure in order to promote additional crosslinking to achieve higher temperature (250-300 C) capability. A preliminary study to build tensile specimens by LS and the corresponding DSC and rheology study of RTM370 during LS process is presented.

Mechanical and spectroscopic properties of metal-containing polyimides

NASA Technical Reports Server (NTRS)

Taylor, L. T.; St.clair, A. K.

1983-01-01

The incorporation of specific metal ions into polyimides is described. Detailed studies have included various compounds of copper, lithium, and palladium as dopants. Addition of the metal during polymerization or after formation of the polyamic acid precedes the thermal imidization step. With many dianhydride-diamine-dopant combinations high quality variously colored films are produced. Many metal doped films exhibit (1) improved high temperature adhesive properties, (2) increased electrical conductivity, (3) excellent thermal stability, (4) improved acid/base resistance, (5) increased modulus in flexible films and (6) excellent high temperature tensile strength. X-ray photo-electron spectroscopic study of these films suggests that many of the additives undergo chemical modification during thermal imidization. Palladium dopants appear to be partially reduced to the metallic state, while lithium and copper dopants are probably converted to their oxides. Ion etching experiments with Auger electron spectroscopy monitoring are discussed.

Phenylethynyl Phthalic Anhydride

NASA Technical Reports Server (NTRS)

Hergenrother, Paul M. (Inventor); Smith, Joseph G., Jr. (Inventor)

1997-01-01

Controlled molecular weight PhenylEthynyl Terminated Imide oligomers (PETIs) have been prepared by the cyclodehydration of precursor phenylethynyl terminated amic acid oligomers. Amino terminated amic acid oligomers are prepared from the reaction of dianhydride(s) with an excess of diamine(s) and subsequently endcapped with PhenylEthynyl Phthalic Anhydride(s) (PEPA). The polymerizations are carried out in polar aprotic solvents such as N-methyl-2pyrrolidinone or N N-dimethylacetamide under nitrogen at room temperature. The amic acid oligomers are subsequently cyclodehydrated either thermally or chemically to the corresponding imide oligomers. Direct preparation of PETIs from the reaction of dianhydride(s) with an excess of diamine(s) and endcapped with phenylethynyl phthalic anhydride(s) has been performed in m-cresol. Phenylethynyl phthalic anhydrides are synthesized by the palladium catalyzed reaction of phenylacetylene with bromo substituted phthalic anhydrides in triethylamine. These new materials exhibit excellent properties and are potentially useful as adhesives, coatings, films, moldings and composite matrices.

Comparing two tetraalkylammonium ionic liquids. II. Phase transitions.

PubMed

Lima, Thamires A; Paschoal, Vitor H; Faria, Luiz F O; Ribeiro, Mauro C C; Ferreira, Fabio F; Costa, Fanny N; Giles, Carlos

2016-06-14

Phase transitions of the ionic liquids n-butyl-trimethylammonium bis(trifluoromethanesulfonyl)imide, [N1114][NTf2], and methyl-tributylammonium bis(trifluoromethanesulfonyl)imide, [N1444][NTf2], were investigated by differential scanning calorimetry (DSC), X-ray diffraction (XRD) measurements, and Raman spectroscopy. XRD and Raman spectra were obtained as a function of temperature at atmospheric pressure, and also under high pressure at room temperature using a diamond anvil cell (DAC). [N1444][NTf2] experiences glass transition at low temperature, whereas [N1114][NTf2] crystallizes or not depending on the cooling rate. Both the ionic liquids exhibit glass transition under high pressure. XRD and low-frequency Raman spectra provide a consistent physical picture of structural ordering-disordering accompanying the thermal events of crystallization, glass transition, cold crystallization, pre-melting, and melting. Raman spectra in the high-frequency range of some specific cation and anion normal modes reveal conformational changes of the molecular structures along phase transitions.

High Temperature Transfer Molding Resins Based on 2,3,3',4'-Biphenyltetracarboxylic Dianhydride

NASA Technical Reports Server (NTRS)

Smith, J. G., Jr.; Connell, J. W.; Hergenrother, P. M.; Yokota, R.; Criss, J. M.

2002-01-01

As part of an ongoing effort to develop materials for resin transfer molding (RTM) processes to fabricate high performance/high temperature composite structures, phenylethynyl containing imides have been under investigation. New phenylethynyl containing imide compositions were prepared using 2,3,3',4'-biphenyltetracarboxylic dianhydride (a-BPDA) and evaluated for cured glass transition temperature (Tg), melt flow behavior, and for processability into flat composite panels via RTM. The a-BPDA imparts a unique combination of properties that are desirable for high temperature transfer molding resins. In comparison to its symmetrical counterpart (i.e. 3,3',4,4'-biphenyltetracarboxylic dianhydride), a-BPDA affords oligomers with lower melt viscosities and when cured, higher Tgs. Several candidates exhibited the appropriate combination of properties such as a low and stable melt viscosity required for RTM processes, high cured Tg, and moderate toughness. The chemistry, physical, and composite properties of select resins will be discussed.

Mechanical and spectroscopic properties of metal containing polyimides

NASA Technical Reports Server (NTRS)

Taylor, L. T.; St. Clair, A. K.

1984-01-01

The incorporation of specific metal ions into polyimides is described. Detailed studies have included various compounds of copper, lithium, and palladium as dopants. Addition of the metal during polymermzation or after formation of the polyamic acid precedes the thermal imidization step. With many dianhydride-diamine-dopant combinations high quality variously colored films are produced. Many metal doped films exhibit (1) improved high temperature adhesive properties, (2) increased electrical conductivity, (3) excellent thermal stability, (4) improved acid/base resistance, (5) increased modulus in flexible films and (6) excellent high temperature tensile strength. X-ray photo-electron spectroscopic study of these films suggests that many of the additives undergo chemical modification during thermal imidization. Palladium dopants appear to be partially reduced to the metallic state, while lithium and copper dopants are probably converted to their oxides. Ion etching experiments with Auger electron spectroscopy monitoring are discussed.

Regulation of substituent groups on morphologies and self-assembly of organogels based on some azobenzene imide derivatives

NASA Astrophysics Data System (ADS)

Jiao, Tifeng; Wang, Yujin; Zhang, Qingrui; Zhou, Jingxin; Gao, Faming

2013-04-01

In this paper, new azobenzene imide derivatives with different substituent groups were designed and synthesized. Their gelation behaviors in 21 solvents were tested as novel low-molecular-mass organic gelators. It was shown that the alkyl substituent chains and headgroups of azobenzene residues in gelators played a crucial role in the gelation behavior of all compounds in various organic solvents. More alkyl chains in molecular skeletons in present gelators are favorable for the gelation of organic solvents. Scanning electron microscopy and atomic force microscopy observations revealed that the gelator molecules self-assemble into different aggregates, from wrinkle, lamella, and belt to fiber with the change of solvents. Spectral studies indicated that there existed different H-bond formations between amide groups and conformations of methyl chains. The present work may give some insight to the design and character of new organogelators and soft materials with special molecular structures.

Regulation of substituent groups on morphologies and self-assembly of organogels based on some azobenzene imide derivatives

PubMed Central

2013-01-01

In this paper, new azobenzene imide derivatives with different substituent groups were designed and synthesized. Their gelation behaviors in 21 solvents were tested as novel low-molecular-mass organic gelators. It was shown that the alkyl substituent chains and headgroups of azobenzene residues in gelators played a crucial role in the gelation behavior of all compounds in various organic solvents. More alkyl chains in molecular skeletons in present gelators are favorable for the gelation of organic solvents. Scanning electron microscopy and atomic force microscopy observations revealed that the gelator molecules self-assemble into different aggregates, from wrinkle, lamella, and belt to fiber with the change of solvents. Spectral studies indicated that there existed different H-bond formations between amide groups and conformations of methyl chains. The present work may give some insight to the design and character of new organogelators and soft materials with special molecular structures. PMID:23566628

Space Environmentally Durable Polyimides and Copolyimides

NASA Technical Reports Server (NTRS)

Connell, John W. (Inventor); Smith, Joseph G. (Inventor); Hergenrother, Paul M. (Inventor); Watson, Kent A. (Inventor); Thompson, Craig M. (Inventor)

2006-01-01

Polyimides displaying low color in thin films, atomic oxygen resistance, vacuum ultraviolet radiation resistance, solubility in organic solvents in the imide form, high glass transition (T(sub g)) temperatures, and high thermal stability are provided. The poly(amide acid)s, copoly(amide acid)s, polyimides and copolyimides are prepared by the reaction of stoichiometric ratios of an aromatic &anhydride with diamines which contain phenylphosphine oxide groups in polar aprotic solvents. Controlled molecular weight oligomeric (amide acid)s and imides can be prepared by offsetting the stoichiometry according to the Carothers equation using excess diamine and endcapping with aromatic anhydrides. The polyimide materials can be processed into various material forms such as thin films, fibers, foams, threads, adhesive film, coatings, dry powders, and fiber coated prepreg, and uses include thin film membranes on antennas, second-surface mirrors, thermal optical coatings, and multilayer thermal insulation (MLI) blanket materials.

Modified Phenylethynyl Containing Imides for Secondary Bonding: Non-Autoclave, Low Temperature Processable Adhesives

NASA Technical Reports Server (NTRS)

Dezern, James F. (Technical Monitor); Chang, Alice C.

1999-01-01

As part of a program to develop structural adhesives for high performance aerospace applications, research continued on the development of modified phenylethynyl containing imides, LaRC(trademark)MPEIs. In previous reports, the polymer properties were controlled by varying the molecular weight, the amount of branching, and the phenylethynyl content and by blending with low molecular weight materials. This research involves changing the flexibility in the copolyimide backbone of the branched, phenylethynyl terminated adhesives. These adhesives exhibit excellent processability at pressures as low as 15 psi and temperatures as low as 288 C. The Ti/Ti lap shear specimens are processable in an autoclave or a temperature programmable oven under a vacuum bag at 288-300 C without external pressure. The cured polymers exhibit high mechanical properties and excellent solvent resistance. The chemistry and properties of these adhesives are presented.

Space Environmentally Durable Polyimides and Copolyimides

NASA Technical Reports Server (NTRS)

Connell, John W. (Inventor); Smith, Joseph G., Jr. (Inventor); Hergenrother, Paul M. (Inventor); Watson, Kent A. (Inventor); Thompson, Craig M. (Inventor)

2005-01-01

Polyimides displaying low color in thin films, atomic oxygen resistance, vacuum ultraviolet radiation resistance, solubility in organic solvents in the imide form, high glass transition (T(sub g)) temperatures, and high thermal stability are provided. The poly(amide acid)s, copoly(amide acid)s, polyimides and copolyimides are prepared by the reaction of stoichiometric ratios of an aromatic dianhydride with diamines which contain phenylphosphine oxide groups in polar aprotic solvents. Controlled molecular weight oligomeric (amide acid)s and imides can be prepared by offsetting the stoichiometry according to the Carothers equation using excess diamine and endcapping with aromatic anhydrides The polyimide materials can be processed into various material forms such as thin films, fibers, foams, threads, adhesive film, coatings, dry powders, and fiber coated prepreg, and uses include thin film membranes on antennas, second-surface mirrors, thermal optical coatings, and multilayer thermal insulation (MLI) blanket materials.

Neutral tumor evolution in myeloma is associated with poor prognosis.

PubMed

Johnson, David C; Lenive, Oleg; Mitchell, Jonathan; Jackson, Graham; Owen, Roger; Drayson, Mark; Cook, Gordon; Jones, John R; Pawlyn, Charlotte; Davies, Faith E; Walker, Brian A; Wardell, Christopher; Gregory, Walter M; Cairns, David; Morgan, Gareth J; Houlston, Richard S; Kaiser, Martin F

2017-10-05

Recent studies suggest that the evolutionary history of a cancer is important in forecasting clinical outlook. To gain insight into the clonal dynamics of multiple myeloma (MM) and its possible influence on patient outcomes, we analyzed whole exome sequencing tumor data for 333 patients from Myeloma XI, a UK phase 3 trial and 434 patients from the CoMMpass study, all of which had received immunomodulatory drug (IMiD) therapy. By analyzing mutant allele frequency distributions in tumors, we found that 17% to 20% of MM is under neutral evolutionary dynamics. These tumors are associated with poorer patient survival in nonintensively treated patients, which is consistent with the reduced therapeutic efficacy of microenvironment-modulating IMiDs. Our findings provide evidence that knowledge of the evolutionary history of MM has relevance for predicting patient outcomes and personalizing therapy. © 2017 by The American Society of Hematology.

Fungal Infections and New Biologic Therapies.

PubMed

Vallabhaneni, Snigdha; Chiller, Tom M

2016-05-01

The development of biologic therapies targeting proinflammatory mediators has led to significant advances in the treatment of immune-mediated inflammatory diseases (IMIDs). Blocking undesired inflammatory effects also has the potential to disrupt the body's immune response and increase the risk for infections, including fungal infections. This review summarizes the published data on the frequency and risk for fungal infections among patients treated with biologics, with a focus on the newer therapies approved for use with IMIDs in the last 10 years. The use of biologics is associated with a small but important risk of fungal infections. Pneumocystis jirovecii pneumonia, histoplasmosis, and candidiasis are some of the most common fungal infections associated with biologics. Providers should be vigilant for fungal infection among patients taking biologics, be aware that biologic agents may alter the typical presentation of fungal infections, and take timely steps to diagnose and treat fungal infection to reduce resultant morbidity and mortality.

Liquid Crystalline Thermosets from Ester, Ester-imide, and Ester-amide Oligomers

NASA Technical Reports Server (NTRS)

Dingemans, Theodorus J. (Inventor); Weiser, Erik S. (Inventor); St. Clair, Terry L. (Inventor)

2009-01-01

Main chain thermotropic liquid crystal esters, ester-imides, and ester-amides were prepared from AA, BB, and AB type monomeric materials and end-capped with phenylacetylene, phenylmaleimide, or nadimide reactive end-groups. The end-capped liquid crystal oligomers are thermotropic and have, preferably, molecular weights in the range of approximately 1000-15,000 grams per mole. The end-capped liquid crystaloligomers have broad liquid crystalline melting ranges and exhibit high melt stability and very low melt viscosities at accessible temperatures. The end-capped liquid crystal oli-gomers are stable forup to an hour in the melt phase. They are highly processable by a variety of melt process shape forming and blending techniques. Once processed and shaped, the end-capped liquid crystal oigomers were heated to further polymerize and form liquid crystalline thermosets (LCT). The fully cured products are rubbers above their glass transition temperatures.

Core Perylene Diimide Designs via Direct Bay- and ortho-(Poly)trifluoromethylation: Synthesis, Isolation, X-Ray Structures, Optical and Electronic Properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clikeman, Tyler T.; Bukovsky, Eric V.; Wang, Xue-Bin

2015-09-22

We developed an efficient solvent- and catalyst-free direct polytrifluoromethylation of solid perylene-3,4,9,10-tetracarboxylic dianhydride that produced a new family of (poly)perfluoroalkyl bay- and ortho-substituted PDIs with two different imide substituents. Direct hydrogen substitution with CN group led to the synthesis of a cyanated perfluoroalkyl PDI derivative for the first time. Absorption, steady-state and time-resolved emission, X-ray diffraction, electrochemical, and gas-phase electron affinity data allowed for systematic studies of substitution effects at bay, ortho, and imide positions in the new PDIs. Solid-state packing showed remarkable variations in the intermolecular interactions that are important for charge transport and photophysical properties. Moreover, analysis ofmore » the electrochemical data for 143 electron poor PDIs, including newly reported compounds, revealed some general trends and peculiar effects from substituting electron-withdrawing groups at all three positions.« less

Core Perylene Diimide Designs via Direct Bay and Ortho (Poly)trifluoromethylation: Synthesis, Isolation, X-ray Structures, Optical and Electronic Properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clikeman, Tyler T.; Bukovsky, Eric V.; Wang, Xue B.

2015-09-22

We developed an efficient solvent- and catalyst-free direct polytrifluoromethylation of solid perylene-3,4,9,10-tetracarboxylic dianhydride that produced a new family of (poly)perfluoroalkyl bay and ortho substituted PDIs with two different imide substituents. Direct hydrogen substitution with CN group led to the synthesis of a cyanated perfluoroalkyl PDI derivative for the first time. Absorption, steady-state and time-resolved emission, X-ray diffraction, electrochemical, and gas-phase electron affinity data allowed for systematic studies of substitution effects at bay, ortho, and imide positions in the new PDIs. Solid-state packing showed remarkable variations in the intermolecular interactions that are important for charge transport and photophysical properties. Analysis ofmore » the electrochemical data for 143 electron poor PDIs, including newly reported compounds, revealed some general trends and peculiar effects of electron withdrawing group substitution at all three positions.« less

"Newton's cradle" proton relay with amide-imidic acid tautomerization in inverting cellulase visualized by neutron crystallography.

PubMed

Nakamura, Akihiko; Ishida, Takuya; Kusaka, Katsuhiro; Yamada, Taro; Fushinobu, Shinya; Tanaka, Ichiro; Kaneko, Satoshi; Ohta, Kazunori; Tanaka, Hiroaki; Inaka, Koji; Higuchi, Yoshiki; Niimura, Nobuo; Samejima, Masahiro; Igarashi, Kiyohiko

2015-08-01

Hydrolysis of carbohydrates is a major bioreaction in nature, catalyzed by glycoside hydrolases (GHs). We used neutron diffraction and high-resolution x-ray diffraction analyses to investigate the hydrogen bond network in inverting cellulase PcCel45A, which is an endoglucanase belonging to subfamily C of GH family 45, isolated from the basidiomycete Phanerochaete chrysosporium. Examination of the enzyme and enzyme-ligand structures indicates a key role of multiple tautomerizations of asparagine residues and peptide bonds, which are finally connected to the other catalytic residue via typical side-chain hydrogen bonds, in forming the "Newton's cradle"-like proton relay pathway of the catalytic cycle. Amide-imidic acid tautomerization of asparagine has not been taken into account in recent molecular dynamics simulations of not only cellulases but also general enzyme catalysis, and it may be necessary to reconsider our interpretation of many enzymatic reactions.

Homogeneous lithium electrodeposition with pyrrolidinium-based ionic liquid electrolytes.

PubMed

Grande, Lorenzo; von Zamory, Jan; Koch, Stephan L; Kalhoff, Julian; Paillard, Elie; Passerini, Stefano

2015-03-18

In this study, we report on the electroplating and stripping of lithium in two ionic liquid (IL) based electrolytes, namely N-butyl-N-methylpyrrolidinium bis(fluorosulfonyl) imide (Pyr14FSI) and N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (Pyr14TFSI), and mixtures thereof, both on nickel and lithium electrodes. An improved method to evaluate the Li cycling efficiency confirmed that homogeneous electroplating (and stripping) of Li is possible with TFSI-based ILs. Moreover, the presence of native surface features on lithium, directly observable via scanning electron microscope imaging, was used to demonstrate the enhanced electrolyte interphase (SEI)-forming ability, that is, fast cathodic reactivity of this class of electrolytes and the suppressed dendrite growth. Finally, the induced inhomogeneous deposition enabled us to witness the SEI cracking and revealed previously unreported bundled Li fibers below the pre-existing SEI and nonrod-shaped protuberances resulting from Li extrusion.

The preparation of new perfluoro ether fluids exhibiting excellent thermal-oxidative stabilities

NASA Technical Reports Server (NTRS)

Jones, William R., Jr.; Bierschenk, Thomas R.; Juhlke, Timothy J.; Kawa, Hajima; Lagow, Richard J.

1988-01-01

A series of low molecular weight perfluoroalkyl ethers (PFAEs) were synthesized by direct fluorination. Viscosity-temperature properties and oxidation stabilities were determined. Viscosity-temperature correlations indicated that increases in branching and increases in the size of the branching substituent caused a deterioration in viscometric properties (i.e., an increase in ASTM slope). In addition, increasing the ratio of carbon to oxygen in these compounds also increased the ASTM slope. Preliminary oxidation stability measurements indicated that highly branched PFAE fluids (i.e., those containing quaternary carbons) may be less stable than either those containing a single trifluoromethyl pendant group or those containing no branching at all.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kowarik, S.; Hinderhofer, A.; Wang, C.

Highly crystalline and stable molecular superlattices are grown with the smallest possible stacking period using monolayers (MLs) of the organic semiconductors pentacene (PEN) and perfluoro-pentacene (PFP). Superlattice reflections in X-ray reflectivity and their energy dependence in resonant soft X-ray reflectivity measurements show that PFP and PEN MLs indeed alternate even though the coherent ordering is lost after ~ 4 ML. The observed lattice spacing of 15.9 Å in the superlattice is larger than in pure PEN and PFP films, presumably because of more upright standing molecules and lack of interdigitation between the incommensurate crystalline PEN and PFP layers. The findingsmore » are important for the development of novel organic quantum optoelectronic devices.« less

Membrane separation of ionic liquid solutions

DOEpatents

Campos, Daniel; Feiring, Andrew Edward; Majumdar, Sudipto; Nemser, Stuart

2015-09-01

A membrane separation process using a highly fluorinated polymer membrane that selectively permeates water of an aqueous ionic liquid solution to provide dry ionic liquid. Preferably the polymer is a polymer that includes polymerized perfluoro-2,2-dimethyl-1,3-dioxole (PDD). The process is also capable of removing small molecular compounds such as organic solvents that can be present in the solution. This membrane separation process is suitable for drying the aqueous ionic liquid byproduct from precipitating solutions of biomass dissolved in ionic liquid, and is thus instrumental to providing usable lignocellulosic products for energy consumption and other industrial uses in an environmentally benign manner.

An enantioselective approach to the preparation of chiral sulfones by Ir-catalyzed asymmetric hydrogenation.

PubMed

Peters, Byron K; Zhou, Taigang; Rujirawanich, Janjira; Cadu, Alban; Singh, Thishana; Rabten, Wangchuk; Kerdphon, Sutthichat; Andersson, Pher G

2014-11-26

Several chiral sulfonyl compounds were prepared using the iridium catalyzed asymmetric hydrogenation reaction. Vinylic, allylic and homoallylic sulfone substitutions were investigated, and high enantioselectivity is maintained regardless of the location of the olefin with respect to the sulfone. Impressive stereoselectivity was obtained for dialkyl substitutions, which typically are challenging substrates in the hydrogenation. As expected, the more bulky Z-substrates were hydrogenated slower than the corresponding E isomers, and in slightly lower enantioselectivity.

Synthesis of Heteroaryl Sulfonamides from Organozinc Reagents and 2,4,6-Trichlorophenyl Chlorosulfate

PubMed Central

2016-01-01

A method for the preparation of aryl and heteroaryl sulfonamides using 2,4,6-trichlorophenyl chlorosulfate (TCPC) is described. The reaction of 2-pyridylzinc reagents with TCPC resulted in 2,4,6-trichlorophenyl (TCP) pyridine-2-sulfonates, and the parent pyridine-2-sulfonate was shown to react with amines. Less electron-rich aryl- and heteroarylzinc reagents reacted with TCPC to afford sulfonyl chlorides that were converted in situ to sulfonamides. PMID:26065317

Rotational diffusion of nonpolar and ionic solutes in 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imides: is solute rotation always influenced by the length of the alkyl chain on the imidazolium cation?

PubMed

Gangamallaiah, V; Dutt, G B

2012-10-25

In an attempt to find out whether the length of the alkyl chain on the imidazolium cation has a bearing on solute rotation, temperature-dependent fluorescence anisotropies of three structurally similar solutes have been measured in a series of 1-alkyl-3-methylimidazolium (alkyl = methyl, ethyl, propyl, butyl, and hexyl) bis(trifluoromethylsulfonyl)imides. Solute-solvent coupling constants obtained from the experimentally measured reorientation times with the aid of Stokes-Einstein-Debye hydrodynamic theory indicate that there is no influence of the length of the alkyl chain on the rotation of nonpolar, anionic, and cationic solutes 9-phenylanthracene (9-PA), fluorescein (FL), and rhodamine 110 (R110), respectively. It has also been noticed that the rotational diffusion of 9-PA is closer to the predictions of slip hydrodynamics, whereas the rotation of negatively charged FL and positively charged R110 is almost identical and follows stick hydrodynamics in these ionic liquids. Despite having similar shape and size, ionic solutes rotate slower by a factor of 3-4 compared to the nonpolar solute. Interplay of specific and electrostatic interactions between FL and the imidazolium cation of the ionic liquids, and between R110 and the bis(trifluoromethylsulfonyl)imide anion, appear to be responsible for the observed behavior. These results are an indication that the length of the alkyl chain on the imidazolium cation does not alter their physical properties in a manner that has an effect on solute rotation.

Synthesis, kinetic characterization and metabolism of diastereomeric 2-(1-(4-phenoxyphenylsulfonyl)ethyl)thiiranes as potent gelatinase and MT1-MMP inhibitors.

PubMed

Gooyit, Major; Lee, Mijoon; Hesek, Dusan; Boggess, Bill; Oliver, Allen G; Fridman, Rafael; Mobashery, Shahriar; Chang, Mayland

2009-12-01

Gelatinases (MMP-2 and MMP-9) have been implicated in a number of pathological conditions, including cancer and cardiovascular disease. Hence, small molecule inhibitors of these enzymes are highly sought for use as potential therapeutic agents. 2-(4-Phenoxyphenylsulfonylmethyl)thiirane (SB-3CT) has previously been demonstrated to be a potent and selective inhibitor of gelatinases, however, it is rapidly metabolized because of oxidation at the para position of the phenoxy ring and at the alpha-position to the sulfonyl group. alpha-Methyl variants of SB-3CT were conceived to improve metabolic stability and as mechanistic probes. We describe herein the synthesis and evaluation of these structural variants as potent inhibitors of gelatinases. Two (compounds 5b and 5d) among the four synthetic stereoisomers were found to exhibit slow-binding inhibition of gelatinases and MMP-14 (MT1-MMP), which is a hallmark of the mechanism of this class of inhibitors. The ability of these compounds to inhibit MMP-2, MMP-9, and MMP-14 could target cancer tissues more effectively. Metabolism of the newly synthesized inhibitors showed that both oxidation at the alpha-position to the sulfonyl group and oxidation at the para position of the terminal phenyl ring were prevented. Instead oxidation on the thiirane sulfur is the only biotransformation pathway observed for these gelatinase inhibitors.

Guanidinium ionic liquid-based surfactants as low cytotoxic extractants: Analytical performance in an in-situ dispersive liquid-liquid microextraction method for determining personal care products.

PubMed

Pacheco-Fernández, Idaira; Pino, Verónica; Ayala, Juan H; Afonso, Ana M

2018-07-20

The IL-based surfactant octylguanidinium chloride (C 8 Gu-Cl) was designed and synthetized with the purpose of obtaining a less harmful surfactant: containing guanidinium as core cation and a relatively short alkyl chain. Its interfacial and aggregation behavior was evaluated through conductivity and fluorescence measurements, presenting a critical micelle concentration value of 42.5 and 44.6mmolL -1 , respectively. Cytotoxicity studies were carried out with C 8 Gu-Cl and other IL-based and conventional surfactants, specifically the analogue 1-octyl-3-methylimidazolium chloride (C 8 MIm-Cl), and other imidazolium- (C 16 MIm-Br) and pyridinium- (C 16 Py-Cl) based surfactants, together with the conventional cationic CTAB and the conventional anionic SDS. From these studies, C 8 Gu-Cl was the only one to achieve the classification of low cytotoxicity. An in situ dispersive liquid-liquid microextraction (DLLME) method based on transforming the water-soluble C 8 Gu-Cl IL-based surfactant into a water-insoluble IL microdroplet via a simple metathesis reaction was then selected as the extraction/preconcentration method for a group of 6 personal care products (PCPs) present in cosmetic samples. The method was carried out in combination with high-performance liquid chromatography (HPLC) and diode array detection (DAD). The method was properly optimized, requiring the use of only 30μL of C 8 Gu-Cl for 10mL of aqueous sample with a NaCl content of 8% (w/v) to adjust the ionic strength and pH value of 5. The metathesis reaction required the addition of the anion exchange reagent (bis[(trifluoromethyl)sulfonyl]imide - 1:1 molar ratio), followed by vortex and centrifugation, and dilution of the final microdroplet up to 60μL with acetonitrile before the injection in the HPLC-DAD system. The optimum in situ DLLME-HPLC-DAD method takes ∼10min for the extraction step and ∼22min for the chromatographic separation, with analytical features of low detection limits: down to 0.4μgL -1 ; high reproducibility: with RSD values lower than 10% (intra-day) and 16% (inter-day) for a spiked level of 15μgL -1 ; and an average enrichment factor of 89. The requirement of low volumes (30μL) of a low cytotoxic IL-based surfactant allows the method to be considered less harmful than other common analytical microextraction approaches. Copyright © 2017 Elsevier B.V. All rights reserved.

The Gabriel Synthesis of Benzylamine

ERIC Educational Resources Information Center

Nigh, W. G.

1975-01-01

Describes an undergraduate organic chemistry laboratory experiment which utilizes the Gabriel Synthesis to demonstrate the acidity of imides and to provide an example of nucleophilic substitution reactions. The experiment also demonstrates the laboratory techniques involved in simple and steam distillation, filtration, extraction, and…

(1R,4R,7S)-1,7-Dimethyl-7-(phenyl-sulfonyl-meth-yl)spiro-[bicyclo-[2.2.1]heptane-2,2'-1,3-dioxolane].

PubMed

Wang, Ya-Wen; Peng, Yu

2007-12-06

In the title compound, C(18)H(24)O(4)S, the chiral bicyclo-[2.2.1]heptane group is not symmetrical due to the influence of the substituents. The angle between the three-atom bridge plane and the four-atom planes of the boat-shaped six-membered ring are 55.07 (19) and 56.24 (19)°. The bridgehead angle is 92.75 (17)°.

Diethyl [2,2,2-trifluoro-1-phenyl­sulfonyl­amino-1-(trifluoro­meth­yl)eth­yl]phospho­nate

PubMed Central

Wijeyesakere, Sanjeeva J.; Nasser, Faik A.; Kampf, Jeff W.; Aksinenko, Alexey Y.; Sokolov, Vladimir B.; Malygin, Vladimir V.; Makhaeva, Galina F.; Richardson, Rudy J.

2008-01-01

The title compound, C13H16F6NO5PS, is of inter­est with respect to inhibition of serine hydro­lases. Its structure contains a 1.8797 (13) Å P—C bond and two inter­molecular N—H⋯O=P hydrogen bonds, resulting in centrosymmetric dimers. An intra­molecular N—H⋯O=P hydrogen bond is also present. PMID:19079747

Long Range Materials Research. Appendix 1. Synthesis and Characterization of Supported Organometallic Rhodium (I) Catalysts

DTIC Science & Technology

1974-06-30

hydrosilates, 130 including irradiation by ultraviolet light, elevated temperatures (up to 3500) in sealed tubes, and free radical initiators (up to 10 mol...to 160 ml dry pyridine and stirred at 00 in a 250 ml Erlenmeyer flask fitted with a septum. After the temperature had equilibrated, p-toluene sulfonyl...chloride (80 g, 0.41 mol) was added slowly, carefully maintaining the temperature below 100. The vessel was tightly capped, the mixture stirred an

Tandem Cu-catalyzed ketenimine formation and intramolecular nucleophile capture: Synthesis of 1,2-dihydro-2-iminoquinolines from 1-(o-acetamidophenyl)propargyl alcohols

PubMed Central

Kant, Ruchir

2014-01-01

Summary The copper-catalyzed ketenimine formation reaction of 1-(o-acetamidophenyl)propargyl alcohols with various sulfonyl azides is found to undergo a concomitant intramolecular nucleophile attack to generate 1,2-dihydro-2-iminoquinolines after aromatization (via elimination of acetyl and hydroxy groups) and tautomerization. The reaction produces 4-substituted and 3,4-unsubstituted title compounds in moderate to good yields under mild reaction conditions. PMID:24991276

One-Pot Synthesis of Allylic Sulfones, Ketosulfones, and Trifylallylic Alcohols from Domino Reactions of Allylic Alcohols with Sulfinic Acid under Metal-Free Conditions.

PubMed

Chu, Xue-Qiang; Meng, Hua; Xu, Xiao-Ping; Ji, Shun-Jun

2015-08-03

Invited for the cover of this issue is the group of Shun-Jun Ji and co-workers at Soochow University, (China). The image depicts a cheaper, low-toxic, eco-friendly benign and metal-free methodology incorporating the both aryl and trifyl sulfonyl functionality from allylic alcohols. Read the full text of the article at 10.1002/chem.201500469. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.